WorldWideScience

Sample records for high chloride environments

  1. Effect of Saturated CO2 on Corrosion Behavior of 13Cr Pipe Steel in High Chloride Environment%高氯环境中饱和CO2对13Cr油管钢腐蚀行为的影响

    Institute of Scientific and Technical Information of China (English)

    雷冰; 马元泰; 李瑛; 王福会; 常泽亮; 谢俊峰; 宋文文; 周理志

    2013-01-01

    The effect of saturated CO2 on corrosion behavior of 13Cr pipe steel in high concentration chloride environment was studied by EIS, polarization test, EN test and SEM. The results indicated that the corrosion rate and corrosion probability of 13Cr pipe steel were accelerated in high chloride environment with the presence of saturated CO2. The 13Cr pipe steel suffered from pitting corrosion in high chloride concentration environment, whilst, from uniform corrosion by the synergistic effect of Cl and CO2. The stability of the passive film of 13Cr pipe steel decreased in high concentration chloride environment with saturated CO2, which can be explained by the dehydroxylation of the outer part of the passive film by carbonic acid and the increase of ionic conductivity of the passive film in aqueous electrolytes.%采用电化学阻抗(EIS)、极化曲线、电化学噪声(EN)和扫描电子显微镜(SEM)研究了高氯环境中饱和CO2对13Cr油管钢腐蚀行为的影响.结果表明:饱和CO2加速材料的腐蚀,增大了腐蚀的发生频率,使材料的腐蚀由点蚀转变为均匀腐蚀.碳酸对钝化膜的去羟基化作用和增大钝化膜的导通率,是材料腐蚀行为变化的原因.

  2. Corrosion of copper in alkaline chloride environments

    Energy Technology Data Exchange (ETDEWEB)

    King, F. [Integrity Corrosion Consulting Ltd., Calgary (Canada)

    2002-08-01

    The available literature information on the corrosion and electrochemical behaviour of copper in alkaline environments has been reviewed. The purpose of the review was to assess the impact of an alkaline plume from cementitious material on the corrosion behaviour of a copper canister in an SKB-3 type repository. The effect of the evolution of the environmental conditions within the repository have been considered, including the effects of temperature, redox conditions, pore-water salinity and pH. If the pore-water pH increases prior to the establishment of anoxic conditions, the canister surface will passivate as the pore-water pH exceeds a value of {approx} pH 9. Passivation will result from the formation of a duplex Cu{sub 2}O/Cu(OH){sub 2} film. The corrosion potential will be determined by the equilibrium potential for the Cu{sub 2}O/Cu(OH){sub 2} couple under oxic conditions, or by the Cu/Cu{sub 2}O redox couple under anoxic conditions (in the absence of sulphide). Pitting corrosion is only likely to occur early in the evolution of the repository environment, whilst the canister is still relatively cool (<40 deg C), whilst there is still O{sub 2} available to support localised corrosion, and prior to the increase in pore-water pH and salinity. The subsequent increase in canister surface temperature, pore-water pH and salinity, and decrease in O{sub 2} will make pit initiation less likely, although the canister will remain passive provided the pore-water pH is maintained above pH 9. The higher the pore-water pH, the more strongly the canister is passivated and the less likely the surface is to undergo localised attack. If the pore-water salinity increases prior to the increase in pH, there could be a period of active canister corrosion before passivation occurs.Under these circumstances, the corrosion potential will be a true mixed potential, determine by the relative kinetics of Cu dissolution as CuCl{sub 2} - and of the reduction of O{sub 2}. The development

  3. Comparison between half-cell potential of reinforced concrete exposed to carbon dioxide and chloride environment

    Directory of Open Access Journals (Sweden)

    Somnuk Tangtermsirikul

    2010-10-01

    Full Text Available The objective of this study is to investigate the effect of concrete mix proportion and fly ash on half-cell potential (HCPand corrosion current density (icorr of steel in concrete exposed to different environments. Reinforced concrete specimenswith different fly ash replacement percentages and water to binder ratios (w/b were studied in this paper. The specimenswere subjected to two highly corrosive environments which are chloride and carbon dioxide. HCP and icorr were used tomonitor the corrosion process. Results of this study demonstrate that both HCP and icorr indicated the same tendency,especially for corroded specimens after being exposed to chloride. This means that HCP can be used to inspect corrosion ofsteel due to chloride. In case of carbonation, concrete specimens with fly ash showed more negative potential values thanconcrete without fly ash. However, chloride exposure test exhibited that specimen with higher fly ash replacement corrodedearlier. Moreover, HCP measurement presented different values between concrete exposed to chloride and carbon dioxide.There was an effect of carbonation to increase HCP during the initiation stage. A proper evaluation guideline for steelcorrosion due to carbonation needs to be further studied.

  4. Ion Transport and Microstructure of Sandwich Cementitious Materials Exposed to Chloride Environment

    Institute of Scientific and Technical Information of China (English)

    WANG Xingang; WANG Kai; WANG Rui; XIE Tao; HUANG Jie

    2015-01-01

    Ion transport of sandwich cementitious materials (SCM) exposed to chloride environment was investigated by accelerated diffusion method and natural diffusion method. Pore structure and micromorphology of SCM were investigated by MIP and SEM-EDS. In comparison with the monolayer structural high performance concrete (HPC), conductive charge for 6 hours, chloride diffusion coefficient, and apparent chloride diffusion coefifcient of SCM were decreased by 30%-40%, two orders of magnitude and 40%-50%, respectively. Pore structure of ultra low ion permeability cementitious materials (ULIPCM) prepared for the facesheet is superior to that of HPC prepared for the core. As for porosity, the most probable pore radius, the content of pores with radius 50 nm and the surface area of pores, the order is ULIPCM

  5. An insight into the passivation of cupronickel alloys in chloride environment

    Indian Academy of Sciences (India)

    J Mathiyarasu; N Palaniswamy; V S Muralidharan

    2001-02-01

    Cupronickels offer enhanced corrosion protection in marine environments by the formation of passive films on the surface. Cyclic voltammetric studies were carried on cupronickels in chloride solutions at H 6.3 to understand the role of chloride ions in passive film formation. Increase in nickel content of the alloy and of chloride ions in solution decreases film resistance. Chloride ions take part in reduction of the passive film to copper. A solid-state model for passive film formation involving chloride ions has been attempted.

  6. Durability Analysis of Subway Station in Chloride Environment

    OpenAIRE

    Yang LuFeng; Yu Bo; Hong Bin

    2013-01-01

    In this study, a finite element model for chloride ions transport in saturated concrete was proposed based on the Fick’s second law of diffusion. The governing partial differential equation was solved numerically in space as a boundary-value problem and in time as an initial-value problem by means of the finite element formulations. The maximum allowable value of chloride diffusion coefficient within different locations of subway station with service life of 100a was achieved and suggestions ...

  7. Denitrification of fertilizer wastewater at high chloride concentration

    DEFF Research Database (Denmark)

    Ucisik, Ahmed Süheyl; Henze, Mogens

    g/l. The results of the experiments showed that biological denitrification was feasible at the extreme environmental conditions prevailing in fertilizer wastewater. Stable continuous biological denitrfication of the synthetic high chloride wastewater was performed up to 77.4 g Cl/l at 37 degree C......Wastewater from fertilizer industry is characterized by high contents of chloride concentration, which normally vary between 60 and 76 g/l. Experiments with bilogical denitrification were performed in lab-scale "fill and draw" reactors with synthetic wastewater with chloride concentrations up to 77.4...

  8. On the Durability of Sealable Circular Concrete Structures under Chloride Environment

    Directory of Open Access Journals (Sweden)

    Changwen Mi

    2015-01-01

    Full Text Available Reinforcement corrosion resulting from chloride attack is one major mechanism that compromises concrete durability. Numerical methods were commonly used for tackling Fick’s diffusion equations. In this paper, we developed a Crank-Nicolson based finite difference scheme suitable for circular concrete structures. Both a time-dependent surface chloride model and diffusivity were considered. The impact of an ideal sealer on chloride redistribution was further investigated. Results suggested that the chloride threshold depth in a concrete structure is greatly affected by the radius of curvature, environment severity, and diffusivity. For sealable concrete structures, both the sealer application timing and location are of great importance.

  9. Separating refractory and non-refractory particulate chloride and estimating chloride depletion by aerosol mass spectrometry in a marine environment

    Directory of Open Access Journals (Sweden)

    I. Nuaaman

    2015-01-01

    Full Text Available Aerosol composition and concentration measurements along the coast of California were obtained using an Aerodyne high-resolution time-of-flight aerosol mass spectrometer (HR-AMS onboard the research vessel Atlantis during the CalNex study in 2010. This paper focuses on the measurement of aerosol chloride using the HR-AMS that can be ambiguous in regions with significant quantities of sea salt aerosols. This ambiguity arises due to large differences in the sensitivity of the HR-AMS to refractory chloride species (i.e., NaCl and non refractory chloride species (i.e., NH4Cl, HCl, etc.. Using the HR-AMS, the aerosol chloride signal is typically quantified using ion signals for 35Cl+, H35Cl+, 37Cl+ and H37Cl+ (HxCl+. During this study, the highest aerosol chloride signal was observed during sea sweep experiments when the source of the aerosol chloride was NaCl present in artificially generated sea salt aerosols even though the HR-AMS has significantly lower sensitivity to such refractory species. Other prominent ion signals that arise from NaCl salt were also observed at m/z 22.99 for Na+ and m/z 57.96 for Na35Cl+ during both sea sweep experiments and during periods of ambient measurements. Thus, refractory NaCl contributes significantly to the HxCl+ signal, interfering with attempts to quantify non sea salt chloride (nssCl. It was found that during ambient aerosol measurements, the interference in the HxCl+ signal from sea salt chloride (ssCl was as high as 89%, but with a study wide average of 10%. The Na35Cl+ ion signal was found to be a good tracer for NaCl. We outline a method to establish nssCl in the ambient aerosols by subtracting the sea salt chloride (ssCl signal from the HxCl+ signal. The ssCl signal is derived from the Na35Cl+ ion tracer signal and the HxCl+ to Na35Cl+ ratio established from the sea sweep experiments. Ambient submicron concentrations of ssCl were also established using the

  10. Electrochemical Migration on Electronic Chip Resistors in Chloride Environments

    DEFF Research Database (Denmark)

    Minzari, Daniel; Jellesen, Morten Stendahl; Møller, Per

    2009-01-01

    Electrochemical migration behavior of end terminals on ceramic chip resistors (CCRs) was studied using a novel experimental setup in varying sodium chloride concentrations from 0 to 1000 ppm. The chip resistor used for the investigation was 10-kΩ CCR size 0805 with end terminals made of 97Sn3Pb...

  11. Anti-chloride permeability and anti-chloride corrodibility of a green high performance concrete admixture in concrete

    Institute of Scientific and Technical Information of China (English)

    ZHENG Yongbao; LIU Xinrong; LIU Dongyan; CHEN Jiangong; HUANG Xiongjun

    2003-01-01

    The effects of green high performance concrete (GHPC) admixture on the anti-chloride permeability and anti- chloride corrodibility of concrete are studied by a series of experiments designed on the basis of the diffusion principle and electrochemical principle. The GHPC admixture consists of fly ash, gangue, slag, red mud, etc., of which the mass fraction of industrial residues is over 96 %. The anti-permeabilities and anti-corrodibilities of the tested GHPC and normal concrete (NC) are evaluated by the Diffusion Coefficients of chloride which was obtained by measuring the concentration of chloride in the tested systems by the voltage difference method. It is found that the adoption of GHPC admixture greatly improves the anti-chloride permeability and anti-chloride corrodibility by modifying the inner structure and contracting the porosity of concrete to the reduce considerably the diffusion rate of chloride. The admixture is desirable regarding its engineering performances as well as economical and environmental interests.

  12. Prediction of the Service Life of a Reinforced Concrete Column under Chloride Environment

    Directory of Open Access Journals (Sweden)

    Mohammad K. Alkam

    2015-01-01

    Full Text Available In the present investigation, service life of a reinforced concrete column exposed to chloride environment has been predicted. This study has been based on numerical simulation of chloride ion diffusion in a concrete column during its anticipated life span. The simulation process has included the concrete cover replacement whenever chloride ion concentration has reached the critical threshold value at the reinforcement surface. Repair scheduling of the concrete column under consideration has been discussed. Effects of the concrete cover thickness and the water cement ratio on the service life of the concrete column at hand have been presented. A new approach for arranging locations of reinforcement steel bars has been introduced. This approach is intended to prolong the service life of the concrete column under consideration against chloride induced corrosion.

  13. High rate lithium/thionyl chloride bipolar battery development

    Energy Technology Data Exchange (ETDEWEB)

    Russell, P.G. [Yardney Technical Products, Inc., Pawcatuck, CT (United States); Goebel, F. [Yardney Technical Products, Inc., Pawcatuck, CT (United States)

    1995-04-01

    The lithium/thionyl chloride (Li/SOCl{sub 2}) electrochemistry is capable of providing high power and high specific power, especially under pulse discharge conditions, when cells containing thin components are arranged in a bipolar configuration. This paper describes recent work concerned with bipolar cell design, cathode evaluation, component manufacturing methods, and the assembly and testing of bipolar modules containing up to 150 cells for Sonobuoy application. (orig.)

  14. High rate lithium-thionyl chloride bipolar battery development

    Energy Technology Data Exchange (ETDEWEB)

    Russell, P.G.; Goebel, F. [Yardney Technical Products, Inc., Pawcatuck, CT (United States)

    1994-12-31

    The lithium/thionyl chloride system is capable of providing both high power and high energy density when cells containing thin components are arranged in a bipolar configuration. Electrode current densities in excess of 300mA/cm{sup 2} are achieved during pulse discharge. The present work is concerned with bipolar cell design, cathode evaluation, component manufacturing methods, and the assembly and testing of bipolar modules containing up to 150 cells.

  15. High rate lithium/thionyl chloride bipolar battery development

    Science.gov (United States)

    Russell, P. G.; Goebel, F.

    The lithium/thionyl chloride ( {Li}/{SOCl2}) electrochemistry is capable of providing high power and high specific power, especially under pulse discharge conditions, when cells containing thin components are arranged in a bipolar configuration. This paper describes recent work concerned with bipolar cell design, cathode evaluation, component manufacturing methods, and the assembly and testing of bipolar modules containing up to 150 cells for Sonobuoy application.

  16. Laboratory investigation of applicability of alkali-activated pozzolana in offshore high chloride environment%碱激发火山灰对近海高氯环境适用性的试验研究

    Institute of Scientific and Technical Information of China (English)

    王运周; 费月英; 杨建国

    2016-01-01

    Offshore roads and bridges were severely eroded by seawater, thus, a new cementitious material of salt-erosion is now urgently needed. Compressive strength of alkali-activated pozzolana (AP) paste mixed with NaCl, X-ray diffraction (XRD) and thermal gravimetric analysis (TGA) were conducted to investigate the influence of NaCl affect strength of AP paste. The results showed that the compressive strength of AP paste strength increases with increase of mixed NaCl,the strength of paste of 30% NaCl content is 2.1 times than the strength of paste without NaCl. XRD, TGA test results showed that two hydrates Friedel salt (FS) and sodium hydroxide (NaOH) were generating in the AP paste which mixed NaCl, these hydrates may be responsible for improving the strength paste, the more hydrates generated, the more optimization AP paste structure, finally the strength increased more significant.AP as a new cementitious material,applicable to high chloride environment of coastal roads and bridge projects.%近海道路桥梁工程受海水侵蚀严重,因此亟需寻求一种耐盐侵蚀的新材料。现对掺入氯化钠(NaCl)的碱激发火山灰(AP)净浆的抗压强度进行测试,同时通过X射线衍射(XRD)、热重分析(TGA)两种微观测试手段,探求NaCl对AP净浆强度的影响作用。试验结果表明:AP净浆抗压强度随NaCl掺入量的增加而增加,NaCl掺量为30%的净浆强度是无NaCl净浆强度的2.1倍。XRD、TGA测试结果表明,掺加NaCl的AP净浆中有新水化物弗里德尔盐(FS)和氢氧化钠(NaOH)生成,这两种水化物的生成可能是造成净浆强度提高的主因,两种水化物生成的越多,AP净浆结构越优化,强度提高越显著。AP作为一种新胶凝材料,可适用于高氯盐环境下的近海道路桥梁工程中。

  17. Dynamic fluorescence quenching of quinine sulfate dication by chloride ion in ionic and neutral micellar environments

    Science.gov (United States)

    Joshi, Sunita; Varma Y, Tej Varma; Pant, Debi D.

    2014-04-01

    Fluorescence quenching of Quinine sulfate dication (QSD) by chloride-ion (Cl-) in micellar environments of anionic, sodium dodecyl sulfate (SDS), cationic, cetyltrimethylammonium bromide (CTAB) and neutral, triton X-100 (TX-100) in aqueous phase has been investigated by time-resolved and steady- state fluorescence measurements. The quenching follows linear Stern-Volmer relation in micellar solutions and is dynamic in nature.

  18. Effects of slag and fly ash in concrete in chloride environment

    NARCIS (Netherlands)

    Polder, R.B.

    2012-01-01

    This paper addresses experience from The Netherlands with blast furnace slag and fly ash in concrete in chloride contaminated environments, both from the field and the laboratory. Use of slag produced in The Netherlands started in the 1930s and CEM III/B LH HS, with typically 70% slag, became the do

  19. High Energy Density Battery Lithium Thionyl Chloride Improved Reverse Voltage Design.

    Science.gov (United States)

    1981-12-01

    BATTERY LITHIUM THIONYL CHLORIDE IMPROVED R-ETC(U) DEC 81 A E ZOLLA N660011-C-0310...HIGH ENERGY DENSITY BATTERY LITHIUM THIONYL CHLORIDE IMPROVED REVERSE VOLTAGE DESIGN Dr. A. E. Zolla Altus Corporation C:1 1610 Crane Court San Jose...reverse aide If necesary and identify by block number) Lithium Battery Lithium Thionyl Chloride High Energy Density Battery Voltage Reversal Battery

  20. A high power lithium thionyl chloride battery for space applications

    Science.gov (United States)

    Shah, Pinakin M.

    1993-03-01

    A high power, 28 V, 330 A h, active lithium thionyl chloride battery has been developed for use as main and payload power sources on an expendable launch vehicle. Nine prismatic cells, along with the required electrical components and a built-in heater system, are efficiently packaged resulting in significant weight savings over presently used silver-zinc batteries. The high rate capability is achieved by designing the cells with a large electrochemical surface area and impregnating an electrocatalyst, polymeric phthalocyanine, into the carbon cathodes. Passivation effects are reduced with the addition of sulfur dioxide into the thionyl chloride electrolyte solution. The results of conducting a detailed thermal analysis are utilized to establish the heater design parameters and the thermal insulation requirements of the battery. An analysis of cell internal pressure and vent characteristics clearly illustrates the margins of safety under different operating conditions. Performance of fresh cells is discussed using polarization scan and discharge data at different rates and temperatures. Self-discharge rate is estimated based upon test results on cells after storage. Results of testing a complete prototype battery are described.

  1. High-rate lithium thionyl-chloride battery development

    Energy Technology Data Exchange (ETDEWEB)

    Cieslak, W.R.; Weigand, D.E.

    1993-12-31

    We have developed a lithium thionyl-chloride cell for use in a high rate battery application to provide power for a missile computer and stage separation detonators. The battery pack contains 20 high surface area ``DD`` cells wired in a series-parallel configuration to supply a nominal 28 volts with a continuous draw of 20 amperes. The load profile also requires six squib firing pulses of one second duration at a 20 ampere peak. Performance and safety of the cells were optimized in a ``D`` cell configuration before progressing to the longer ``DD` cell. Active surface area in the ``D`` cell is 735 cm{sup 2}, and 1650 cm{sup 2} in the ``DD`` cell. The design includes 1.5M LiAlCl{sub 4}/SOCl{sub 2} electrolyte, a cathode blend of Shawinigan Acetylene Black and Cabot Black Pearls 2000 carbons, Scimat ETFE separator, and photoetched current collectors.

  2. Treatment of Highly Turbid Water by Polyaluminum Ferric Chloride (PAFCL

    Directory of Open Access Journals (Sweden)

    Fazel Fazel Mohammadi-Moghaddam

    2015-10-01

    Full Text Available Background & Aims of the Study: In some situation like rainfall seasons raw water become very turbid so it affected the water treatment plant processes and quality of produced water. Treatment of very high turbid water has some concerns like precursors for disinfection by-products and very loading rate of particle on filter's media and consequently increases in water consumption for filter backwash. This paper investigates the performance of a composite inorganic polymer of aluminium and ferric salt, Polyaluminium ferric chloride (PAFCl, for the removal of turbidity, color and natural organic matter (NOM from high turbid water. Materials and Methods: Experiments were carried out by Jar test experiment by synthetic water samples with 250 and 500 NTU turbidity that prepared in laboratory. Results: The results of conventional jar test showed that the optimum pH for coagulation of water sample was 7.5 to 8 and optimum dosage of the coagulant was 10 mg/L. Removal efficiency of turbidity, color and UV adsorbent at 254 nm at optimum dose and pH without filtration was 99.92%, 100% and 80.6% respectively for first sample (250 NTU and 99.95%, 99.49% and 84.77 for second sample (500 NTU respectively. Conclusion: It concluded that polyaluminium ferric chloride has a very good efficiency for the removal of turbidity, color and organic matter in high turbid water. Also it can be select as a coagulant for high turbid water and some waste water from water treatment plant like filter backwash water.

  3. Production of carbon nanofibers in high yields using a sodium chloride support.

    Science.gov (United States)

    Geng, Junfeng; Kinloch, Ian A; Singh, Charanjeet; Golovko, Vladimir B; Johnson, Brian F G; Shaffer, Milo S P; Li, Yali; Windle, Alan H

    2005-09-08

    A new route for the highly convenient scalable production of carbon nanofibers on a sodium chloride support has been developed. Since the support is nontoxic and soluble in water, it can be easily removed without damage to the nanofibers and the environment. Nanofiber yields of up to 6500 wt % relative to the nickel catalyst have been achieved in a growth time of 15 min. Electron microscopy (SEM, TEM) and thermal gravimetric analysis (TGA) indicated that the catalytically grown carbon had relatively little thermal over-growth and possessed either a herringbone or a semi-ordered nanostructure, depending on the growth conditions.

  4. High temperature corrosion in chloridizing atmospheres: development of material quasi-stability diagrams and coatings

    Energy Technology Data Exchange (ETDEWEB)

    Doublet, S.; Schuetze, M. [Karl-Winnacker-Institut der DECHEMA e.V., Theodor-Heuss-Allee 25, D-60486 Frankfurt am Main (Germany)

    2004-07-01

    Chlorine gas is widely encountered in chemical industries, e. g. in waste incinerators and plastic/polymer decomposition mills. The presence of chlorine may significantly reduce the life-time of the components. Although metallic materials have been widely used under such conditions there is still a need for data on the role of the different alloying elements in commercial alloys. The purpose of this work is to produce a clear picture of which alloying elements play a detrimental role and which elements are beneficial. These results can be used as a tool for general assessment of metallic alloys with regard to their performance in chloridizing high temperature environments. A previous study has already been performed in oxidizing-chloridizing atmospheres and led to the elaboration of material quasi-stability diagrams. As a follow-up the present work has been performed in reducing-chloridizing atmospheres in order to validate these diagrams at low partial pressures of oxygen. The behaviour of 9 commercial materials where the content of the major alloying elements was varied in a systematic manner was investigated in reducing-chloridizing atmospheres (in Ar containing up to 2 vol.% Cl{sub 2} and down to 1 ppm O{sub 2}) at 800 deg. C. As the thermodynamical approach to corrosion in such atmospheres could not explain all the phenomena which occur, kinetics calculations i.e. diffusion calculations were carried out. Pack cementation and High Velocity Oxy-Fuel (HVOF) coatings were also developed from the best alloying elements previously found by the calculations and the corrosion experiments. Corrosion tests on the coated materials were then performed in the same conditions as the commercial alloys. (authors)

  5. Studies Leading to the Development of High-Rate Lithium Sulfuryl Chloride Battery Technology.

    Science.gov (United States)

    1982-09-01

    greatest attention has been given to the lithium - thionyl chloride (Li/SOC12 ) system. Cells and batteries have been demonstrated with energy densities...Studies Leading to the Development of High-Rate Lithium Sulfuryl Chloride Battery Technology John C. Hall and Mark Koch Gould Research Center, Materials...High-Rate 11182to 33182 Lithium -Sulfuryl Chloride Battery Technology 1_1/82_to_3/31/82 S. PERFORMING ORO. REPORT NUMBER 2 7. AUTHOR(*) S. CONTRACT OR

  6. KINETICS OF VINYL CHLORIDE (CO)POLYMERIZATION AT HIGH CONVERSION

    Institute of Scientific and Technical Information of China (English)

    Zu-ren Pan; Zhi-xue Weng; Zhi-ming Huang

    1999-01-01

    This paper provides a summarized review on the kinetics of vinyl chloride homopolymerization in the absence and presence of chain transfer agents, of VC/DAP(diallyl phthalate) copolymerization with chain extension and/or slightly crosslinking functions, and of vinylidene chloride/VC random copolymerization.Models of rate, degree of polymerization or molecular weight, copolymer composition, gel fraction and crosslinking density were proposed and interpreted mechanistically.

  7. Extractive process for preparing high purity magnesium chloride hexahydrate

    Directory of Open Access Journals (Sweden)

    Fezei Radouanne

    2012-01-01

    Full Text Available This paper refers a method for the preparation of magnesium chloride hexahydrate (bischofite from Sebkha el Melah of Zarzis Tunisian natural brine. It is a five-stage process essentially based on crystallization by isothermal evaporation and chemical precipitation. The two first steps were dedicated to the crystallization of sodium chloride and potassiummagnesium double salts, respectively. Then, the resulting liquor was desulfated using calcium chloride solution. After that another isothermal evaporation stage was implemented in order to eliminate potassium ions in the form of carnallite, KCl.MgCl2.6H2O. At the end of this step, the recovered solution primarily composed of magnesium and chloride ions was treated by dioxan in order to precipitate magnesium chloride as MgCl2.6H2O.C4H8O2. This compound dried at constant temperature of 100°C gave good quality magnesium chloride hexahydrate. Besides this salt, the various by-products obtained from the different treatment stages are also useful.

  8. Mechanism of sodium chloride in promoting reduction of high-magnesium low-nickel oxide ore.

    Science.gov (United States)

    Zhou, Shiwei; Wei, Yonggang; Li, Bo; Wang, Hua; Ma, Baozhong; Wang, Chengyan

    2016-07-04

    Sodium chloride has been proved that it is an effective promoter for the reduction of high-magnesium, low-nickel oxide ore. The aim of current work is to clarify the promotion behavior of sodium chloride in the roasting reduction process. The influence of moisture on the reduction of ore in the presence of sodium chloride is studied to get clear comprehension of promotion process. In the presence of moisture, the HCl is produced by pyrohydrolysis of sodium chloride for chlorinating nickel and iron oxides, moreover, interactions between metallic oxides and sodium chloride are also a way for chlorination at high temperature (>802 °C); subsequently, the metal chloride would be reduced by reductant. In the absence of moisture, the magnetic separation results show that the recoveries of iron and nickel have a significant increase; moreover, olivine structure would be destroyed gradually with the increase of roasting temperature in the action of sodium chloride, and the sodium chloride existed in high-magnesium, low-nickel oxide ore could make the NiO isolate from NiO-bearing minerals. The NiO reacts with Fe2O3 at high temperature to form NiFe2O4, which is conductive to the formation of Ni-Fe alloy during the reduction process.

  9. Similar Microbial Consortia and Genes Are Involved in the Biodegradation of Benzalkonium Chlorides in Different Environments.

    Science.gov (United States)

    Ertekin, Emine; Hatt, Janet K; Konstantinidis, Konstantinos T; Tezel, Ulas

    2016-04-19

    Benzalkonium chlorides (BACs) are emerging pollutants. Identification of microorganisms and the genes involved in the biodegradation of BACs is crucial for better understanding the fate of BACs in the environment and developing treatment strategies. Four microbial communities degrading BACs were developed from sewage (SEW), activated sludge (AS), soil (SOIL) and sea sediment (SEA) samples. According to 16S rRNA pyrosequencing and shotgun metagenome sequencing analyses, the most abundant species represented uncharacterized members of the Pseudomonas and Achromobacter genera. BAC biotransformation rates of the enriched microbial communities were 2.8, 3.2, 17.8, and 24.3 μM hr(-1) for SEA, AS, SOIL, and SEW, respectively, and were positively correlated with the relative abundance of a particular Pseudomonas sp. strain, BIOMIG1. The strain BIOMIG1 mineralizes BACs at a rate up to 2.40 μmol hr(-1) 10(-11) cells. Genomes of four BAC degrading and nondegrading BIOMIG1 phenotypes were sequenced and differentially compared with each other. As a result, a gene cluster encoding for transporters, an integrase and a dioxygenase were involved in BAC biotransformation. Our results suggest that BIOMIG1 plays a key role on the fate of BACs in the environment and genes, other than those reported to date, are involved in BAC biotransformation in various habitats.

  10. Filtrates & Residues: Experimental Work with Tin (II) Chloride in a High School.

    Science.gov (United States)

    Sanchez, Manuela Martin

    1988-01-01

    Presents a high school chemistry lab experiment using tin (II) chloride to explore the concepts of hydrolysis, Le Chatelier's principle, and electrolysis. Presents methodology and the chemistry involved. Offers questions for the students. (MVL)

  11. Practical analysis of high purity chemicals--V. Precision silver chloride gravimetry.

    Science.gov (United States)

    Little, K

    1971-09-01

    A reasonably simple gravimetric silver chloride procedure with fairly wide tolerance in conditions is presented in full detail with all critical steps and precautions delineated. The procedure allows the precision determination of chloride by analysts having limited expertise with exacting gravimetric methods, and can be performed with equipment common to nearly all laboratories and without dependence on a standard substance. The elapsed and actual working times for the assessment of a solid sample in triplicate are 65 and 10-12 hr respectively. The application of the procedure to the assay of some high-purity chloride salts and to the standardization of hydrochloric acid solutions is described.

  12. Numerical assessment of non-uniform corrosion scenarios of rebar in concrete exposed to natural chloride environment

    Indian Academy of Sciences (India)

    S Muthulingam; B N Rao

    2015-06-01

    Corrosion of embedded rebars is a classical deterioration mechanism that remains as one of the most significant problems limiting the service life of concrete structures exposed to chloride-laden environments. The primary objective of this study is to propose and verify a numerical framework that can efficiently quantify non-uniform corrosion penetration depth along the perimeter of the rebar in concrete exposed to chloride environment. This framework investigates the corrosion process during both the corrosion initiation and propagation phases by exploring the effects of not only the rebar existence but also its sizes and locations. The corrosion initiation phase is examined through a comprehensive chloride ingress model that identifies the most important parameters that influence the intrusion of chlorides into RC. The corrosion propagation phase is studied based on a decisive parameter, namely, the corrosion rate. In addition, the framework evaluates the non-uniform corrosion states that correspond to two scenarios of corrosion penetration depth: corrosion of segment of the rebar and uneven corrosion along the rebar perimeter. Numerical solution shows that, in general, chloride build-up along the perimeter of the corner bar is not only faster but also higher than that of the middle bar. Moreover, for the given values of cover thickness and water-to-binder ratio, time-to-corrosion initiation for the corner bar is faster than that for the middle bar. Furthermore, the larger the rebar, in general, the bigger the obstruction, and therefore, the higher the chloride build-up. Qualitative comparisons of the evaluated non-uniform corrosion scenarios with the variety of available laboratory and field data show good agreement.

  13. Corrosion of reinforcement induced by environment containing chloride and carbon dioxide

    Indian Academy of Sciences (India)

    Vladimír Živica

    2003-10-01

    Reinforced concrete structures during their exploitation may be exposed to the common action of carbonation and chlorides causing corrosion of steel reinforcement. Therefore, the related data seem to be interesting and important when the evaluation of the service life of the structures is the object of interest. This fact was a motivation for the present experimental study on the sequence of action of chloride solutions and carbonation of the embedding concrete. The results obtained show that carbonation of concrete foregoing the action of chloride solutions may intensify the process of corrosion of steel reinforcement in comparison to the converse sequence of the action of mentioned media. At the same time the natrium chloride solution has been shown as a more aggressive medium opposite to the calcium and magnesium chloride solutions.

  14. TESTING OF 304L STAINLESS STEEL IN NITRIC ACID ENVIRONMENTS WITH FLUORIDES AND CHLORIDES

    Energy Technology Data Exchange (ETDEWEB)

    Mickalonis, J.

    2010-10-04

    Impure radioactive material processed in nitric acid solutions resulted in the presence of chlorides in a dissolver fabricated from 304L stainless steel. An experimental program was conducted to study the effects of chloride in nitric acid/fluoride solutions on the corrosion of 304L stainless steel. The test variables included temperature (80, 95, and 110 C) and the concentrations of nitric acid (6, 12, and 14 M), fluoride (0.01, 0.1, and 0.2 M) and chloride (100, 350, 1000, and 2000 ppm). The impact of welding was also investigated. Results showed that the chloride concentration alone was not a dominant variable affecting the corrosion, but rather the interaction of chloride with fluoride significantly affected corrosion.

  15. Chloride Penetration through Cracks in High-Performance Concrete and Surface Treatment System for Crack Healing

    Directory of Open Access Journals (Sweden)

    In-Seok Yoon

    2012-01-01

    Full Text Available For enhancing the service life of concrete structures, it is very important to minimize crack at surface. Even if these cracks are very small, the problem is to which extend these cracks may jeopardize the durability of these decks. It was proposed that crack depth corresponding with critical crack width from the surface is a crucial factor in view of durability design of concrete structures. It was necessary to deal with chloride penetration through microcracks characterized with the mixing features of concrete. This study is devoted to examine the effect of high strength concrete and reinforcement of steel fiber on chloride penetration through cracks. High strength concrete is regarded as an excellent barrier to resist chloride penetration. However, durability performance of cracked high strength concrete was reduced seriously up to that of ordinary cracked concrete. Steel fiber reinforcement is effective to reduce chloride penetration through cracks because steel fiber reinforcement can lead to reduce crack depth significantly. Meanwhile, surface treatment systems are put on the surface of the concrete in order to seal the concrete. The key-issue is to which extend a sealing is able to ensure that chloride-induced corrosion can be prevented. As a result, penetrant cannot cure cracks, however, coating and combined treatment can prevent chloride from flowing in concrete with maximum crack width of 0.06 mm and 0.08 mm, respectively.

  16. Chloride Transport of High Alumina Cement Mortar Exposed to a Saline Solution

    Directory of Open Access Journals (Sweden)

    Hee Jun Yang

    2016-01-01

    Full Text Available Chloride transport in different types of high alumina cement (HAC mortar was investigated in this study. Three HAC cement types were used, ranging from 52.0 to 81.1% of aluminum oxides in clinker. For the development of the strength, the setting time of fresh mortar was measured immediately after mixing and the mortar compressive strength was cured in a wet chamber at 25 ± 2°C and then measured at 1–91 days. Simultaneously, to assess the rate of chloride transport in terms of diffusivity, the chloride profile was performed by an exposure test in this study, which was supported by further experimentation including an examination of the pore structure, chloride binding, and chemical composition (X-ray diffraction analysis. As a result, it was found that an increase in the Al2O3 content in the HAC clinker resulted in an increase in the diffusion coefficient and concentration of surface chloride due to increased binding of chloride. However, types of HAC did not affect the pore distribution in the cement matrix, except for macro pores.

  17. Development of Modified 304 Stainless Steel Resistant to Stress Corrosion Cracking in Chloride Environment

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    This was a feasibility study for a modified 304 steel resistant to stress corrosion cracking (SCC) in aqueous environment containing chloride. SCC tests were conducted potentiostaticaly with spot-welded specimens, which had both crevice and residual stress, mainly in 3 % NaCl solution at various temperatures to determine the critical temperature for SCC at and below which the steel would not suffer from SCC. The effects of individual alloying element of silicon, manganese and copper on SCC of 18Cr-14Ni steels which phosphor content is 0.002 % and molybdenum content is 0.01 % were examined. Addition of 1 or 2 % of copper has beneficial effect on resistance to SCC, while increasing silicon or manganese content has no significant effect. Critical temperature of the steel with 0.002 % of phosphor and 2 % of copper is 150 ℃, which is markedly higher than 50 ℃ of 304L steel. However, the beneficial effect of copper is reduced with increasing phosphor content. From practical viewpoint, the modified steel with good SCC resistance should have 0.01 %-0.015 % of phosphor and 0.3 % or more of molybdenum, because it is very difficult to reduce phosphor content below 0.008 % industrially and such molybdenum content is inevitably introduced through cost-saving melting process using return steel. Aluminium is to be added as another alloying element and 3 % of aluminium combined with 2 % of copper has been found to negate the deleterious effects of increased phosphor and molybdenum content. As a candidate steel at this stage, 14Cr-16Ni-0.013P-2Cu-1Al-(0.3-1)Mo steel has critical temperature of 110 ℃.

  18. Use of sodium chloride and zeolite during shipment of Ancistrus triradiatus under high temperature

    Directory of Open Access Journals (Sweden)

    Wilson F. Ramírez-Duarte

    Full Text Available The use of sodium chloride (0.5 g/L and 1 g/L and zeolite (22.7 g/L during shipment (48 h of Ancistrus triradiatus at high temperatures (between 24.5 and 34ºC were evaluated. Several water quality parameters (dissolved oxygen, pH, conductivity, and total ammonia were measured before and after shipment. Glycemia was measured before shipment and at 24 and 48 h after shipment. After shipment, a resistance test was carried out in a high concentration of sodium chloride, and mortality was recorded after shipment, and 7 days post-shipment. While the two evaluated substances increased survival of A. triradiatus challenged by high temperatures during shipment, the best result was obtained with 1 g/L of sodium chloride.

  19. Metal chloride-treated graphene oxide to produce high-performance polymer solar cells

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Eun-Su; Noh, Yong-Jin; Kwon, Sung-Nam; Na, Seok-In, E-mail: nsi12@jbnu.ac.kr [Professional Graduate School of Flexible and Printable Electronics and Polymer Materials Fusion Research Center, Chonbuk National University, 664-14, Deokjin-dong, Deokjin-gu, Jeonju-si, Jeollabuk-do 561-756 (Korea, Republic of); Jeon, Ye-Jin [School of Materials Science and Engineering, Gwangju Institute of Science and Technology, Gwangju 500-712 (Korea, Republic of); Kim, Seok-Soon, E-mail: sskim@kunsan.ac.kr [Department of Nano and Chemical Engineering, Kunsan National University, Kunsan, Jeollabuk-do 753-701 (Korea, Republic of); Kim, Tae-Wook [Soft Innovative Materials Research Center, Institute of Advanced Composite Materials, Korea Institute of Science and Technology, San 101, Eunha-ri, Bongdong-eup, Wanju-gun, Jeollabuk-do 565-905 (Korea, Republic of)

    2015-07-13

    We introduce a simple but effective graphene oxide (GO) modification with metal chloride treatments to produce high-performance polymer solar cells (PSCs). The role of various metal chlorides on GO and their effects on device performances of PSCs was investigated. X-ray photoelectron spectroscopy, ultraviolet photoemission spectroscopy, and current-voltage measurement studies demonstrated that metal chloride can induce a p-doping effect and increase the GO work-function, thus resulting in an improved built-in potential and interfacial resistance in PSCs. The resultant PSCs with metal chloride exhibited improved device efficiency than those with the neat GO. Furthermore, with the metal chloride-doped GO, we finally achieved an excellent PSC-efficiency of 6.58% and a very desirable device stability, which constitute a highly similar efficiency but much better PSC life-time to conventional device with poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS). This study could be a valuable way to produce various PEDOT:PSS alternatives and beneficial for producing high-performance and cost-efficient polymeric devices.

  20. High filler concrete using fly ash. Chloride penetration and microstructure

    NARCIS (Netherlands)

    Valcke, S.L.A.; Polder, R.B.; Nijland, T.G.; Leegwater, G.A.; Visser, J.H.M.; Bigaj-van Vliet, A.J.

    2012-01-01

    Most high filler concrete studies are based on relatively high contents of powder (cement + filler) (>400 kg m-3). This paper aims to increase the total fly ash content relative to the clinker content, while simultaneously minimizing the total powder content in the concrete to values lower than 300

  1. New Potentiometric Wireless Chloride Sensors Provide High Resolution Information on Chemical Transport Processes in Streams

    Directory of Open Access Journals (Sweden)

    Keith Smettem

    2017-07-01

    Full Text Available Quantifying the travel times, pathways, and dispersion of solutes moving through stream environments is critical for understanding the biogeochemical cycling processes that control ecosystem functioning. Validation of stream solute transport and exchange process models requires data obtained from in-stream measurement of chemical concentration changes through time. This can be expensive and time consuming, leading to a need for cheap distributed sensor arrays that respond instantly and record chemical transport at points of interest on timescales of seconds. To meet this need we apply new, low-cost (in the order of a euro per sensor potentiometric chloride sensors used in a distributed array to obtain data with high spatial and temporal resolution. The application here is to monitoring in-stream hydrodynamic transport and dispersive mixing of an injected chemical, in this case NaCl. We present data obtained from the distributed sensor array under baseflow conditions for stream reaches in Luxembourg and Western Australia. The reaches were selected to provide a range of increasingly complex in-channel flow patterns. Mid-channel sensor results are comparable to data obtained from more expensive electrical conductivity meters, but simultaneous acquisition of tracer data at several positions across the channel allows far greater spatial resolution of hydrodynamic mixing processes and identification of chemical ‘dead zones’ in the study reaches.

  2. New Potentiometric Wireless Chloride Sensors Provide High Resolution Information on Chemical Transport Processes in Streams

    Science.gov (United States)

    Smettem, Keith; Harris, Nick; Cranny, Andy; Klaus, Julian; Pfister, Laurent

    2016-04-01

    Quantifying the travel times, pathways and dispersion of solutes moving through stream environments is critical for understanding the biogeochemical cycling processes that control ecosystem functioning. Validation of stream solute transport and exchange process models requires data obtained from in-stream measurement of chemical concentration changes through time. This can be expensive and time consuming, leading to a need for cheap distributed sensor arrays that respond instantly and record chemical transport at points of interest on timescales of seconds. To meet this need we apply new, low-cost (in the order of a euro per sensor) potentiometric chloride sensors used in a distributed array to obtain data with high spatial and temporal resolution. The application here is to monitoring in-stream hydrodynamic transport and dispersive mixing of an injected chemical, in this case NaCl. We present data obtained from the distributed sensor array under baseflow conditions for three stream reaches in Luxembourg. Sensor results are comparable to data obtained from more expensive electrical conductivity meters and allow spatial resolution of hydrodynamic mixing processes and identification of chemical 'dead zones' in the study reaches.

  3. A cleaner two-step synthesis of high purity diallyldimethylammonium chloride monomers for flocculant preparation

    Institute of Scientific and Technical Information of China (English)

    TIAN Bing-hui; FAN Bin; PENG Xian-jia; LUAN Zhao-kun

    2005-01-01

    In order to improve the flocculation efficiency of polydiallyldimethylammonium chloride (PDADMAC), high molecular weight PDADMAC should be prepared from high purity diallyldimethylammonium chloride(DADMAC) monomers. In this paper, a cleaner method with microwave irradiation and alkali solidification was proposed for preparing high pure DADMAC by selective heating under low temperature, and the prepared high purity DADMAC is characterized using FTIR and atomic absorption spectrometry. The new method provides a solution to the key technical problem of PDADMAC synthesis. Comparing with the conventional methods, the results showed that the advantages of the novel synthesis include: (a) high purity DADMAC is improved from 57% to 71%; (b) reaction time of tertiary amine preparation is shortened from 6 h to 7 min; (c) water instead of acetone was used as reaction medium; (d) toxic by-products,wastewater and waste gas are eliminated. Flocculant made from the synthesized high purity DADMAC monomers was proved more efficient in flocculation tests.

  4. Effect of Nitrate on the Repassivation Potential of Alloy 22 in Chloride Containing Environment

    Energy Technology Data Exchange (ETDEWEB)

    G. Ilevbare; K. King; S. Gordon; H. Elayat; G. Gdowski; T. Summers

    2004-09-21

    The study of Alloy 22 was undertaken in several selected nitrate/chloride (NO{sub 3}{sup -}/Cl{sup -}) electrolytes with chloride concentrations [Cl{sup -}] of 1.0, 3.5 and 6.0 molal with [NO{sub 3}{sup -}]/[Cl{sup -}] ratios of 0.05, 0.15 and 0.5 at temperatures up to 100 C. The repassivation potentials increased with increase in [NO{sub 3}{sup -}]/[Cl{sup -}] ratio and decreased with increase in temperature. The absolute [Cl{sup -}] was found to have less of an effect on the repassivation potential compared with temperature and the [NO{sub 3}{sup -}]/[Cl{sup -}]. Regression analyses were carried out to describe the relationship between the repassivation potential, temperature, [Cl{sup -}] and [NO{sub 3}{sup -}] for the conditions tested.

  5. Effect of Nitrate on the Repassivation Potential of Alloy 22 in Chloride Containing Environment

    Energy Technology Data Exchange (ETDEWEB)

    G. Ilevbare; K. King; S. Gordon; H. Elayat; G. Gdowski; T. Summers

    2004-09-21

    The study of Alloy 22 was undertaken in several selected nitrate/chloride (NO{sub 3}{sup -}/Cl{sup -}) electrolytes with chloride concentrations [Cl{sup -}] of 1.0, 3.5 and 6.0 molal with [NO{sub 3}{sup -}]/[Cl{sup -}] ratios of 0.05, 0.15 and 0.5 at temperatures up to 100 C. The repassivation potentials increased with increase in [NO{sub 3}{sup -}]/[Cl{sup -}] ratio and decreased with increase in temperature. The absolute [Cl{sup -}] was found to have less of an effect on the repassivation potential compared with temperature and the [NO{sub 3}{sup -}]/[Cl{sup -}]. Regression analyses were carried out to describe the relationship between the repassivation potential, temperature, [Cl{sup -}] and [NO{sub 3}{sup -}] for the conditions tested.

  6. EFFECT OF NITRATE ON THE REPASSIVATION POTENTIAL OF ALLOY 22 IN CHLORIDE CONTAINING ENVIRONMENTS.

    Energy Technology Data Exchange (ETDEWEB)

    Ilevbare, G; King, K; Gordon, S; Elayat, H; Gdowski, G; Summers, T

    2004-08-16

    The study of Alloy 22 was undertaken in several selected nitrate/chloride (NO{sub 3}{sup -}/Cl{sup -}) electrolytes with chloride concentrations [Cl{sup -}] of 1.0, 3.5 and 6.0 molal with [NO{sub 3} {sup -}]/[Cl{sup -}] ratios of 0.05, 0.15 and 0.5 at temperatures up to 100 C. Results showed that the repassivation potentials increased with increase in [NO{sub 3} {sup -}]/[Cl{sup -}] ratio and decreased with increase in temperature. The absolute [Cl{sup -}] was found to have less of an effect on the repassivation potential compared with temperature and the NO{sub 3} {sup -}/Cl{sup -}. Regression analyses were carried out and expressions were derived to describe the relationship between the repassivation potential, temperature, [Cl{sup -}] and [NO{sub 3} {sup -}] for the conditions tested.

  7. Hydrogen embrittlement of type 410 stainless steel in sodium chloride, sodium sulfate, and sodium hydroxide environments at 90 C

    Energy Technology Data Exchange (ETDEWEB)

    Gonzalez-Rodriguez, J.G.; Salinas-Bravo, V.M. [Inst. de Investigaciones Electricas, Cuernavaca (Mexico). Dept. Fisico Quimica Aplicada; Martinez-Villafane, A. [Centro de Investigaciones en Materiales Avanzados Leon Tolstoi, Chihuahua (Mexico)

    1997-06-01

    Susceptibility of martensitic type 410 (UNS S41000) stainless steel (SS) to environmental cracking was evaluated at 90 C in concentrated sodium chloride, sodium sulfate and sodium hydroxide solutions, all of which are environments related to steam turbine conditions, using the slow strain rate testing (SSRT) technique. In NaCl, the effects of solution pH, concentration, and anodic and cathodic polarization were investigated. Tests were supplemented by detailed electron fractography and hydrogen permeation measurements. A clear correlation was found between the degree of embrittlement and the amount of hydrogen permeating the steel, suggesting a hydrogen-induced cracking mechanism.

  8. Investigation of high-rate lithium-thionyl chloride cells

    Science.gov (United States)

    Hayes, Catherine A.; Gust, Steven; Farrington, Michael D.; Lockwood, Judith A.; Donaldson, George J.

    Chemical analysis of a commercially produced high-rate D-size lithium-thionyl cell was carried out, as a function of rate of discharge (1 ohm and 5 ohms), depth of discharge, and temperature (25 C and -40 C), using specially developed methods for identifying suspected minor cell products or impurities which may effect cell performance. These methods include a product-retrieval system which involves solvent extraction to enhance the recovery of suspected semivolatile minor chemicals, and methods of quantitative GC analysis of volatile and semivolatile products. The nonvolatile products were analyzed by wet chemical methods. The results of the analyses indicate that the predominant discharge reaction in this cell is 4Li + 2SOCl2 going to 4LiCl + S + SO2, with SO2 formation decreasing towards the end of cell life (7 to 12 Ah). The rate of discharge had no effect on the product distribution. Upon discharge of the high-rate cell at -40 C, one cell exploded, and all others exhibited overheating and rapid internal pressure rise when allowed to warm up to room temperature.

  9. Chloride ingress in concrete as measured by field exposure tests in the atmospheric, tidal and submerged zones of a tropical marine environment

    Energy Technology Data Exchange (ETDEWEB)

    Roy, S.K. (National Univ. of Singapore (Singapore). School of Building and Estate Management); Chye, Liam Kok (Matcor Technology and Services (Singapore)); Northwood, D.O. (National Univ. of Singapore (Singapore). Dept. of Mechanical and Production Engineering Univ. of Windsor, Ontario (Canada). Engineering Materials Group)

    1993-11-01

    Five grades of concrete were exposed in the atmosphere, tidal and submerged zones of a tropical marine environment for times up to 80 weeks and the chloride ion ingress profiles determined. The measured chloride profiles were compared with profiles calculated on the basis of diffusion theory and the agreement was found to be reasonably good for all 3 zones. Diffusion coefficients, D, for the chloride ion calculated from the measured ingress profiles agreed well with previous data from laboratory tests and from surveys of marine structures. D was found to be mainly dependent on the water/cement (W/C) ratio and changed little with the addition of superplasticizers. The use of data for the diffusion coefficient, D, and equilibrium surface chloride level, Ce, obtained from the chloride ingress profiles, to the calculation of the time-to-initiation for corrosion of the steel reinforcement is briefly discussed.

  10. A High-affinity Activator of G551D-CFTR Chloride Channel Identified By High Throughput Screening

    Institute of Scientific and Technical Information of China (English)

    ZHAO Lu; HE Cheng-yan; LIU Yan-li; ZHOU Hong-lan; ZHOU Jin-song; SHANG De-jing; YANG Hong

    2004-01-01

    A stably transfected CHO cell line coexpressing G551D-CFTR and iodide-sensitive yellow fluorescent protein mutant EYFP-H148Q-I152L was successfully established and used as assay model to identify small-molecule activators of G551D-CFTR chloride channel from 100000 diverse combinatorial compounds by high throughput screening on a customized Beckman robotic system. A bicyclooctane compound was identified to activate G551D-CFTR chloride channel with high-affinity(Kd=1.8 μmol/L). The activity of the bicyclooctane compound is G551D-CFTR-specific, reversible and non-toxic. The G551D-CFTR activator may be useful as a tool to study the mutant G551D-CFTR chloride channel structure and transport properties and as a candidate drug to cure cystic fibrosis caused by G551D-CFTR mutation.

  11. 盐湖氯化物资源开发与环保%Development of Salt Lake Chloride Resoures and Environment Protection

    Institute of Scientific and Technical Information of China (English)

    乌志明; 温现明

    2000-01-01

    简述了盐湖氯化物资源综合开发势在必行;探讨开展氯化学研究的必要;并对与氯平衡相关的环保问题和水制约问题做了分析。%This paper breifs the necessity of comprehensive development of salt lake chloride resources and study on chloride chemistry,analyze the issues coneerning chloride related environment proteetion and water shortage.

  12. High pressure electrical resistivity study on nonlinear bis thiourea cadmium chloride (BTCC) single crystal

    Energy Technology Data Exchange (ETDEWEB)

    Ariponnammal, S.; Radhika, S. [Department of Physics, Gandhigram Rural Institute, Deemed University, Gandhigram - 624 302, Dindigul District, Tamil Nadu (India); Selva Vennila, R. [Department of Physics, Anna University, Chennai - 600 025 (India); Arumugam, S. [Department of Physics, Bharathidasan University, Trichy (India)

    2005-09-01

    The Bis Thiourea Cadmium Chloride (BTCC) crystals have been crystallized by slow evaporation technique. The lattice parameters of the grown crystals have been determined by the Energy dispersive x-ray diffraction technique (EDXRD) and the structure has been confirmed. The high pressure electrical resistivity study have been carried out on this crystal and the results have been reported here. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  13. Hot Corrosion Behavior of Arc-Sprayed Highly Dense NiCr-Based Coatings in Chloride Salt Deposit

    Science.gov (United States)

    Qin, Enwei; Yin, Song; Ji, Hua; Huang, Qian; Liu, Zekun; Wu, Shuhui

    2017-03-01

    To make cities more environmentally friendly, combustible wastes tend to be incinerated in waste-to-energy power plant boilers. However, release of chlorine gas (Cl2) during incineration causes serious problems related to hot corrosion of boiler tubes and poses a safety threat for such plants. In this study, a pseudo-de Laval nozzle was employed in a twin-wire arc spray system to enhance the velocity of in-flight particles. Highly dense NiCr-based coatings were obtained using the modified nozzle gun. The coating morphology was characterized by optical microscopy and scanning electron microscopy, and hot corrosion testing was carried out in a synthetic molten chloride salt environment. Results showed that the dense NiCr-based coatings exhibited high resistance against corrosion by chlorine, which can be related to the typical splat lamellar microstructure and chemical composition as well as minor alloying elements such as Ti and Mo.

  14. Hot Corrosion Behavior of Arc-Sprayed Highly Dense NiCr-Based Coatings in Chloride Salt Deposit

    Science.gov (United States)

    Qin, Enwei; Yin, Song; Ji, Hua; Huang, Qian; Liu, Zekun; Wu, Shuhui

    2017-04-01

    To make cities more environmentally friendly, combustible wastes tend to be incinerated in waste-to-energy power plant boilers. However, release of chlorine gas (Cl2) during incineration causes serious problems related to hot corrosion of boiler tubes and poses a safety threat for such plants. In this study, a pseudo-de Laval nozzle was employed in a twin-wire arc spray system to enhance the velocity of in-flight particles. Highly dense NiCr-based coatings were obtained using the modified nozzle gun. The coating morphology was characterized by optical microscopy and scanning electron microscopy, and hot corrosion testing was carried out in a synthetic molten chloride salt environment. Results showed that the dense NiCr-based coatings exhibited high resistance against corrosion by chlorine, which can be related to the typical splat lamellar microstructure and chemical composition as well as minor alloying elements such as Ti and Mo.

  15. Highly selective oxidative dehydrogenation of ethane with supported molten chloride catalysts

    Energy Technology Data Exchange (ETDEWEB)

    Gaertner, C.A.; Veen, A.C. van; Lercher, J.A. [Technische Univ. Muenchen (Germany). Catalysis Research Center

    2011-07-01

    Ethene production is one of the most important transformations in chemical industry, given that C{sub 2}H{sub 4} serves as building block for many mass-market products. Besides conventional thermal processes like steam cracking of ethane, ethane can be produced selectively by catalytic processes. One of the classes of catalysts that have been reported in literature as active and highly selective for the oxidative dehydrogenation of ethane is that of supported molten chloride catalysts, containing an alkali chloride overlayer on a solid support. This work deals with fundamental aspects of the catalytic action in latter class of catalysts. Results from kinetic reaction studies are related to observations in detailed characterization and lead to a comprehensive mechanistic understanding. Of fundamental importance towards mechanistic insights is the oxygen storage capacity of the catalysts that has been determined by transient step experiments. (orig.)

  16. INFLUENCE OF POZZOLANA ON THE HYDRATION OF C4AF RICH CEMENT IN CHLORIDE ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    IRMANTAS BARAUSKAS

    2013-03-01

    Full Text Available This study investigated the influence of natural pozzolana - opoka additive on the hydration of C4AF rich cement and the effects of chloride ions on the hydrates formed. In the samples, 25 % (by weight of the sintered C4AF rich cement and OPC was replaced with pozzolana. The mixtures were hardened for 28 days in water, soaked in a saturated NaCl solution for 3 months at 20°C. It was estimated that under normal conditions, pozzolana additive accelerates the hydration of calcium silicates and initiates the formation of CO32- - AFm in the Brownmillerite rich cement. However, the hydration of Brownmillerite cement with opoka additive is still slower to compare with hydration of Portland cement. Also, opoka decreases total porosity and threshold pore diameter of Brownmillerite cement paste after two days of hydration. After 28 days of hydration threshold pore diameter became smaller even to compare with threshold pore diameter of Portland cement. Opoka additive promotes the formation of Friedel’s salt in Brownmillerite samples treated in saturated NaCl solution, because CO32-–AFm affected by saturated NaCl solution become unstable and takes part in reactions producing Friedel’s salt.

  17. Chloride-Ion Penetrability and Mechanical Analysis of High Strength Concrete with Copper Slag

    Directory of Open Access Journals (Sweden)

    Savaş Erdem

    2014-05-01

    Full Text Available The use of waste materials and industrial by-products in high-strength concrete could increase the sustainability of the construction industry. In this study, the potential of using copper slag as coarse aggregate in high-strength concrete was experimentally investigated. The effects of replacing gravel coarse aggregate by copper slag particles on the compressive strength, chloride ion- migration, water permeability and impact resistance of high-strength concretes were evaluated. Incorporating copper slag coarse particles resulted in a compressive strength increase of about 14 % on average partly due to the low Ca/Si ratio through the interface area of this concrete (more homogenous internal structure as confirmed by the energy dispersive X-ray micro chemical analysis. It was also found that the copper slag high-strength concrete provided better ductility and had much greater load carrying capacity compared to gravel high-strength concrete under dynamic conditions. Finally, it was observed that in comparison to the high strength concrete with slag, the chloride migration coefficient from non-steady state migration was approximately 30 % greater in the gravel high-strength concrete.

  18. Sulfate and Chloride Resistance of High Fluidity Concrete including Fly Ash and GGBS for NPP

    Energy Technology Data Exchange (ETDEWEB)

    Noh, Jea Myoung; Cho, Myung Sug [KEPCO Research Institute, Daejeon (Korea, Republic of)

    2010-10-15

    Fly ash mixed concrete has been used for NPP concrete structures in Korea in order to prevent aging and improve durability since the Shin.Kori no.1,2 in 2005. Concentrated efforts to develop technology for the streamlining of construction work and to affect labor savings have been conducted in construction. The application of high fluidity concrete for nuclear power plants has been the research subject with the aim of further rationalization of construction works. Since high fluidity concrete can have the characteristics of high density and high strength without compaction. However, high fluidity concrete can cause thermal cracking by heat of hydration. For this reason, the amount of pozzolan binder should be increased in high fluidity concrete for nuclear power plants. In this study, the resistance of high fluidity concrete on sulfate and chloride was compared with that of the concrete currently using for nuclear power plants

  19. Use of sodium chloride and zeolite during shipment of Ancistrus triradiatus under high temperature

    Directory of Open Access Journals (Sweden)

    Wilson F. Ramírez-Duarte

    2011-01-01

    Full Text Available The use of sodium chloride (0.5 g/L and 1 g/L and zeolite (22.7 g/L during shipment (48 h of Ancistrus triradiatus at high temperatures (between 24.5 and 34ºC were evaluated. Several water quality parameters (dissolved oxygen, pH, conductivity, and total ammonia were measured before and after shipment. Glycemia was measured before shipment and at 24 and 48 h after shipment. After shipment, a resistance test was carried out in a high concentration of sodium chloride, and mortality was recorded after shipment, and 7 days post-shipment. While the two evaluated substances increased survival of A. triradiatus challenged by high temperatures during shipment, the best result was obtained with 1 g/L of sodium chloride.O uso de cloreto de sódio (0,5 g/L e 1 g/L e zeolita (22,7 g/L foram avaliados durante o transporte (48 h de Ancistrus triradiatus em altas temperaturas (entre 24,5 e 34ºC. Os seguintes parâmetros foram monitorados: pH, oxigênio dissolvido, condutividade e amônia antes e depois do transporte. Também foi mensurada a concentração de glicose no sangue antes do transporte e 0, 24 e 48 h após o transporte. Foi realizado um teste de resistência a altas concentrações de cloreto de sódio após o transporte, sendo registrada a mortalidade no final do transporte e após 7 dias. As duas substâncias testadas aumentam a sobrevivência de A. triradiatus a altas temperaturas durante o transporte, porém o melhor resultado foi obtido com o uso de 1 g/L cloreto de sódio.

  20. Effect of chloride impurities on the performance and durability of polybenzimidazole-based high temperature proton exchange membrane fuel cells

    DEFF Research Database (Denmark)

    Ali, Syed Talat; Li, Qingfeng; Pan, Chao

    2011-01-01

    The effect of chloride as an air impurity and as a catalyst contaminant on the performance and durability of polybenzimidazole (PBI)-based high temperature proton exchange membrane fuel cell (HT-PEMFC) was studied. The ion chromatographic analysis reveals the existence of chloride contaminations...... temperatures in 85% phosphoric acid containing chloride ions showed both increase in oxidation and reduction current densities. The fuel cell performance, i.e. the current density at a constant voltage of 0.4 V and 0.5 V was found to be degraded as soon as HCl was introduced in the air humidifier...... in the Pt/C catalysts. Linear sweep voltammetry was employed to study the redox behavior of platinum in 85% phosphoric acid containing chloride ions, showing increase in oxidation and decrease in reduction current densities during the potential scans at room temperature. The potential scans at high...

  1. Development and characterization of a high capacity lithium/thionyl chloride battery

    Science.gov (United States)

    Boyle, Gerald H.; Goebel, Franz

    A 30 V lithium/thionyl chloride battery with 320 Ah capacity capable of operating at currents of 14 to 75 A has been developed and tested over a temperature range from 15 to 71 °C. The 81 lb battery consists of nine series connected cylindrical cells in a three-by-three arrangement within an aluminum case. The cells are of a parallel disc electrode design with a total active surface area of 10 200 cm 2. Cells and batteries have each been tested for safety, performance and to a space environment. The battery has clearly performed in excess of the specification requirements. The cell design is very adaptable to many battery design requirements.

  2. Development and characterization of a high capacity lithium/thionyl chloride battery

    Energy Technology Data Exchange (ETDEWEB)

    Boyle, G.H. [Yardney Technical Products, Inc., Pawcatuck, CT (United States); Goebel, F. [Yardney Technical Products, Inc., Pawcatuck, CT (United States)

    1995-04-01

    A 30 V lithium/thionyl chloride battery with 320 Ah capacity capable of operating at currents of 14 to 75 A has been developed and tested over a temperature range from 15 to 71 C. The 81 lb battery consists of nine series connected cylindrical cells in a three-by-three arrangement within an aluminum case. The cells are of a parallel disc electrode design with a total active surface area of 10 200 cm{sup 2}. Cells and batteries have each been tested for safety, performance and to a space environment. The battery has clearly performed in excess of the specification requirements. The cell design is very adaptable to many battery design requirements. (orig.)

  3. The hypertonic environment differentially regulates wild-type CFTR and TNR-CFTR chloride channels.

    Science.gov (United States)

    Lassance-Soares, Roberta M; Cheng, Jie; Krasnov, Kristina; Cebotaru, Liudmila; Cutting, Garry R; Souza-Menezes, Jackson; Morales, Marcelo M; Guggino, William B

    2010-01-01

    This study tested the hypotheses that the hypertonic environment of the renal medulla regulates the expression of cystic fibrosis transmembrane conductance regulator protein (CFTR) and its natural splice variant, TNR-CFTR. To accomplish this, Madin-Darby canine kidney (MDCK) stable cell lines expressing TNR-CFTR or CFTR were used. The cells were treated with hypertonic medium made with either NaCl or urea or sucrose (480 mOsm/kg or 560 mOsm/kg) to mimic the tonicity of the renal medulla environment. Western blot data showed that CFTR and TNR-CFTR total cell protein is increased by hypertonic medium, but using the surface biotinylation technique, only CFTR was found to be increased in cell plasma membrane. Confocal microscopy showed TNR-CFTR localization primarily at the endoplasmic reticulum and plasma membrane. In conclusion, CFTR and TNR-CFTR have different patterns of distribution in MDCK cells and they are modulated by a hypertonic environment, suggesting their physiological importance in renal medulla.

  4. Development of a 300 Amp-hr high rate lithium thionyl chloride cell

    Science.gov (United States)

    Boyle, Gerard H.

    1991-01-01

    The development of a high-rate lithium thionyl chloride cylindrical cell with parallel plate electrodes is discussed. The development was divided into three phases: phase 1, a 150 Amp/hour low rate (1 mA/sq cm) design; phase 2, a 25 Amp/hour high rate (5 mA/sq cm) design; and phase 3, a 300 Amp/hour high rate (5 mA/sq cm) design. The basic design is the same for all three cells. The electrodes are perpendicular to the axis of the cylinder. Multiple electrodes are bussed up the side of the cylinder, 180 deg apart allowing excellent anode and cathode utilization. It is a lithium limited design with excess electrolyte. The cathode is Shawinigan or Gulf Acetylene black with no catalyst. The electrolyte is 1.8 Molar lithium tetrachloroaluminate (LiAlCl4) in thionyl chloride. All cell cases are 304L Stainless Steel with a BS&B burst disc.

  5. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    Prediction of chloride ingress into concrete is an important part of durability design of reinforced concrete structures exposed to chloride containing environment. This paper presents experimentally based design parameters for Portland cement concretes with and without silica fume and fly ash...... in marine atmospheric and submersed South Scandinavian environment. The design parameters are based on sequential measurements of 86 chloride profiles taken over ten years from 13 different types of concrete. The design parameters provide the input for an analytical model for chloride profiles as function...

  6. High glucose inhibits ClC-2 chloride channels and attenuates cell migration of rat keratinocytes.

    Science.gov (United States)

    Pan, Fuqiang; Guo, Rui; Cheng, Wenguang; Chai, Linlin; Wang, Wenping; Cao, Chuan; Li, Shirong

    2015-01-01

    Accumulating evidence has demonstrated that migration of keratinocytes is critical to wound epithelialization, and defects of this function result in chronic delayed-healing wounds in diabetes mellitus patients, and the migration has been proved to be associated with volume-activated chloride channels. The aim of the study is to investigate the effects of high glucose (HG, 25 mM) on ClC-2 chloride channels and cell migration of keratinocytes. Newborn Sprague Dawley rats were used to isolate and culture the keratinocyte in this study. Immunofluorescence assay, real-time polymerase chain reaction, and Western blot assay were used to examine the expression of ClC-2 protein or mRNA. Scratch wound assay was used to measure the migratory ability of keratinocytes. Transwell cell migration assay was used to measure the invasion and migration of keratinocytes. Recombinant lentivirus vectors were established and transducted to keratinocytes. Whole-cell patch clamp was used to perform the electrophysiological studies. We found that the expression of ClC-2 was significantly inhibited when keratinocytes were exposed to a HG (25 mM) medium, accompanied by the decline of volume-activated Cl(-) current (I Cl,vol), migration potential, and phosphorylated PI3K as compared to control group. When knockdown of ClC-2 by RNAi or pretreatment with wortmannin, similar results were observed, including I Cl,vol and migration keratinocytes were inhibited. Our study proved that HG inhibited ClC-2 chloride channels and attenuated cell migration of rat keratinocytes via inhibiting PI3K signaling.

  7. Kinetic Study of Photocatalytic Degradation of Tolonium Chloride Under High Pressure Irradiation in Aquatic Buffer Systems

    Directory of Open Access Journals (Sweden)

    M. Montazerozohori

    2011-01-01

    Full Text Available Anatase titanium dioxide catalyzed photodegradation of tolonium chloride at various bufferic pH of 2, 7, 9 and 12 in aqueous solution is presented. The effect of some physicochemical parameters such as initial concentration of dye, catalyst amount and reaction time on photocatalytic degradation has been investigated in a photo-reactor cell containing high pressure mercury lamp to obtain the optimum conditions in each bufferic pH at constant temperature. A complete spectrophotometric kinetic study of tolonium chloride under high pressure irradiation at buffer media was performed. The photocatalytic degradation observed rate constants (kobs were found to be 2.90×10-3, 3.30×10-3, 3.20×10-3 and 5.20×10-3 min-1 for buffer pH of 2-12 respectively. It was found that a pseudo-first-order kinetic model based on Langmuir-Hinshelwood one is usable to photodegradation of this compound at all considered buffer pH. In addition to these, the Langmuir-Hinshelwood rate constants, kr for the titled compound at various pH are reported.

  8. Heavy-Metal and Benzalkonium Chloride Resistance of Listeria monocytogenes Isolates from the Environment of Turkey-Processing Plants▿ †

    Science.gov (United States)

    Mullapudi, S.; Siletzky, R. M.; Kathariou, S.

    2008-01-01

    The resistance of Listeria monocytogenes to cadmium and arsenic has been used extensively for strain subtyping. However, limited information is available on the prevalence of such resistance among isolates from the environment of food-processing plants. In addition, it is not known whether the resistance of such isolates to heavy metals may correlate with resistance to quaternary ammonium compounds extensively used as disinfectants in the food-processing industry. In this study, we characterized 192 L. monocytogenes isolates (123 putative strains) from the environment of turkey-processing plants in the United States for resistance to cadmium and arsenic and to the quaternary ammonium disinfectant benzalkonium chloride (BC). Resistance to cadmium was significantly more prevalent among strains of serotypes 1/2a (or 3a) and 1/2b (or 3b) (83% and 74%, respectively) than among strains of the serotype 4b complex (19%). Resistance to BC was encountered among 60% and 51% of the serotype 1/2a (or 3a) and 1/2b (or 3b) strains, respectively, and among 7% of the strains of the serotype 4b complex. All BC-resistant strains were also resistant to cadmium, although the reverse was not always the case. In contrast, no correlation was found between BC resistance and resistance to arsenic, which overall was low (6%). Our findings suggest that the processing environment of turkey-processing plants may constitute a reservoir for L. monocytogenes harboring resistance to cadmium and to BC and raise the possibility of common genetic elements or mechanisms mediating resistance to quaternary ammonium disinfectants and to cadmium in L. monocytogenes. PMID:18192428

  9. Methyl Chloride from Direct Methane Partial Oxidation: A High-Temperature Shilov-Like Catalytic System

    Energy Technology Data Exchange (ETDEWEB)

    Yongchun Tang; John (Qisheng) Ma

    2012-03-23

    The intention of this study is to demonstrate and evaluate the scientific and economic feasibility of using special solvents to improve the thermal stability of Pt-catalyst in the Shilov system, such that a high reaction temperature could be achieved. The higher conversion rate (near 100%) of methyl chloride from partial oxidation of methane under the high temperature ({approx} 200 C) without significant Pt0 precipitation has been achieved. High concentration of the Cl- ion has been identified as the key for the stabilization of the Pt-catalysts. H/D exchange measurements indicated that the over oxidation will occur at the elevated temperature, developments of the effective product separation processes will be necessary in order to rationalize the industry-visible CH4 to CH3Cl conversion.

  10. Synthesis of tetrakis (hydroxymethyl) phosphonium chloride by high-concentration phosphine in industrial off-gas.

    Science.gov (United States)

    Huang, Xiaofeng; Wei, Yanfu; Zhou, Tao; Qin, Yangsong; Gao, Kunyang; Ding, Xinyue

    2013-01-01

    With increasing consumption of phosphate rock and acceleration of global phosphate production, the shortage of phosphate resources is increasing with the development and utilization of phosphate. China's Ministry of Land and Resources has classified phosphate as a mineral that cannot meet China's growing demand for phosphate rock in 2010. The phosphorus chemical industry is one of the important economic pillars for Yunnan province. Yellow phosphorus production in enterprises has led to a significant increase in the amount of phosphorus sludge. This paper focuses on phosphine generation in the process of phosphoric sludge utilization, where the flame retardant tetrakis (hydroxymethyl) phosphonium chloride (THPC) is synthesized by high concentrations of phosphine. The optimum conditions are determined at a space velocity of 150 h(-1), a reaction temperature of 60 °C, 0.75 g of catalyst, and a ratio of raw materials of 4:1. Because of the catalytic oxidation of copper chloride (CuCl2), the synthesis of THPC was accelerated significantly. In conclusion, THPC can be efficiently synthesized under optimal conditions and with CuCl2 as a catalyst.

  11. Cytological comparison of gill chloride cells and blood serum ion concentrations in kutum (Rutilus frisii kutum spawners from brackish (Caspian Sea and fresh water (Khoshkrood River environments

    Directory of Open Access Journals (Sweden)

    Ghahremanzadeh Zahra

    2014-09-01

    Full Text Available The size and number of chloride cells and serum ion concentrations in kutum, Rutillus frisii kutum Nordman, from brackish (Caspian Sea and fresh water (Khoshkrood River environments were studied to gain a better understanding of osmoregulation in this species. Twenty mature kutum specimens were collected from the Caspian Sea (Anzali coasts, 8.49 ppt salinity and 12.4°C temperature and 20 specimens from Khoshkrood River (0.18 ppt salinity and 18°C temperature. Gill samples were analyzed histologically and concentrations of Na+, Cl- , K+, and Mg2+ ions were determined in the blood serum. Concentrations of Na+, Cl- , K+, and Mg2+ ions and osmotic pressure in mature kutum from brackish water were significantly higher than in specimens from fresh water. The average size and number of chloride cells in the fish from seawater were considerably larger than those from fresh water. The mean size of chloride cells was 6.89 ± 1.16 μm in brackish water samples and 5.1 ± 0.81 μm in river samples. The average number of chloride cells in brackish and river water samples were 16.92 and 6.57, respectively. The density and size of chloride cells increased with increases in salinity

  12. Rust Layer Formed on Low Carbon Weathering Steels with Different Mn, Ni Contents in Environment Containing Chloride Ions

    Directory of Open Access Journals (Sweden)

    Gui-qin FU

    2016-11-01

    Full Text Available The rusting evolution of low carbon weathering steels with different Mn, Ni contents under a simulated environment containing chloride ions has been investigated to clarify the correlation between Mn, Ni and the rust formed on steels. The results show that Mn contents have little impact on corrosion kinetics of experimental steels. Content increase of Ni both enhances the anti-corrosion performance of steel substrate and the rust. Increasing Ni content is beneficial to forming compact rust. Semi-quantitative XRD phase analysis shows that the quantity ratio of α/γ*(α-FeOOH/(γ-FeOOH+Fe3O4 decreases as Mn content increases but it increases as Ni content increases. Ni enhances rust layer stability but Mn content exceeding 1.06 wt.% is disadvantageous for rust layer stability. The content increase of Mn does not significantly alter the parameters of the polarization curve. However, as Ni contents increases, Ecorr has shifted to the positive along with decreased icorr values indicating smaller corrosion rate especially as Ni content increases from 0.42 wt.% to 1.50 wt.%.DOI: http://dx.doi.org/10.5755/j01.ms.22.4.12844

  13. Investigation of thermodynamic properties of magnesium chloride amines by HPDSC and TG. For application in a high-lift high-temperature chemical heat pump

    NARCIS (Netherlands)

    Bevers, E.R.T.; Oonk, H.A.J.; Haije, W.G.; Ekeren, P.J. van

    2007-01-01

    The formation as well as the decomposition of magnesium chloride ammonia complexes was studied by high-pressure differential scanning calorimetry (HPDSC) and thermogravimetric analysis (TG). HPDSC runs were performed under constant ammonia pressure conditions to determine the transition temperatures

  14. Investigation of thermodynamic properties of magnesium chloride amines by HPDSC and TG. For application in a high-lift high-temperature chemical heat pump

    NARCIS (Netherlands)

    Bevers, E.R.T.; Oonk, H.A.J.; Haije, W.G.; Ekeren, P.J. van

    2007-01-01

    The formation as well as the decomposition of magnesium chloride ammonia complexes was studied by high-pressure differential scanning calorimetry (HPDSC) and thermogravimetric analysis (TG). HPDSC runs were performed under constant ammonia pressure conditions to determine the transition temperatures

  15. Highly reflective and adhesive surface of aluminized polyvinyl chloride film by vacuum evaporation

    Science.gov (United States)

    Li, Denian; Tai, Qile; Feng, Qiang; Li, Qi; Xu, Xizhe; Li, Hairong; Huang, Jing; Dong, Lijie; Xie, Haian; Xiong, Chuanxi

    2014-08-01

    Aluminized poly(vinyl chloride) (PVC) film with high reflectivity and strong adhesion was facilely fabricated by vacuum evaporation. The technical study revealed that both alkali-pretreatment of the PVC matrix and thermal annealing after aluminization could greatly promote the peeling adhesion force of this metal/polymer composite by producing interfacial active chemical groups and removing the inner stress, respectively. Reflectivity test and AFM study indicated that the reflecting capacitance of the aluminum coating was closely related to the surface roughness, which can be easily controlled by modulating deposition of aluminum. Moreover, the formation of aluminum layer follows an island model process, and a continuous and smooth coating with highest reflectivity and lowest surface resistance was achieved at deposition time of 60 s. We anticipate that the cost-effective metallized PVC film by this strategy may find extensive applications in light harvesting, solar energy, and flexible mirrors, among others.

  16. A highly versatile catalyst system for the cross-coupling of aryl chlorides and amines.

    Science.gov (United States)

    Lundgren, Rylan J; Sappong-Kumankumah, Antonia; Stradiotto, Mark

    2010-02-08

    The syntheses of 2-(di-tert-butylphosphino)-N,N-dimethylaniline (L1, 71%) and 2-(di-1-adamantylphosphino)-N,N-dimethylaniline (L2, 74 %), and their application in Buchwald-Hartwig amination, are reported. In combination with [Pd(allyl)Cl](2) or [Pd(cinnamyl)Cl](2), these structurally simple and air-stable P,N ligands enable the cross-coupling of aryl and heteroaryl chlorides, including those bearing as substituents enolizable ketones, ethers, esters, carboxylic acids, phenols, alcohols, olefins, amides, and halogens, to a diverse range of amine and related substrates that includes primary alkyl- and arylamines, cyclic and acyclic secondary amines, N-H imines, hydrazones, lithium amide, and ammonia. In many cases, the reactions can be performed at low catalyst loadings (0.5-0.02 mol % Pd) with excellent functional group tolerance and chemoselectivity. Examples of cross-coupling reactions involving 1,4-bromochlorobenzene and iodobenzene are also reported. Under similar conditions, inferior catalytic performance was achieved when using Pd(OAc)(2), PdCl(2), [PdCl(2)(cod)] (cod = 1,5-cyclooctadiene), [PdCl(2)(MeCN)(2)], or [Pd(2)(dba)(3)] (dba = dibenzylideneacetone) in combination with L1 or L2, or by use of [Pd(allyl)Cl](2) or [Pd(cinnamyl)Cl](2) with variants of L1 and L2 bearing less basic or less sterically demanding substituents on phosphorus or lacking an ortho-dimethylamino fragment. Given current limitations associated with established ligand classes with regard to maintaining high activity across the diverse possible range of C-N coupling applications, L1 and L2 represent unusually versatile ligand systems for the cross-coupling of aryl chlorides and amines.

  17. SECM Study of Effect of Chromium Content on the Localized Corrosion Behavior of Low-Alloy Steels in Chloride Environment

    Science.gov (United States)

    Indira, K.; Nishimura, T.

    2016-10-01

    This paper investigates the effect of chromium (Cr) content (0, 1, 3 and 5% Cr) in epoxy-coated alloy steel against corrosion using in situ electrochemical techniques such as EIS and SECM in a 3% NaCl solution. The EIS results revealed that the epoxy-coated Cr steel exhibited higher impedance values than carbon steel, which is attributed to the greater resistance of Cr steel toward corrosion. Based on the cyclic voltammogram results, the tip potentials were set at -0.7, 0.04 and 0.60 V for determining the concentration of dissolved oxygen at cathodic region, and oxidation of Cr2+ and Fe2+ at anodic region, respectively. The SECM measurements showed that, the tip current in the anodic region has decreased with increase in Cr content of the sample, which indicates that the oxidation of Fe2+ and Cr2+ decreases (corrosion is reduced) with the increase in Cr content of the steel. Besides, 5% Cr steel can maintain the highest corrosion resistance, and 1 and 3% Cr steels have higher corrosion resistance than the 0% Cr steel. This higher corrosion resistance of Cr steel samples could be due to the formation of Cr-rich hydro-oxide layers [Cr(OH)3 as a corrosion product] on the surface of the samples. Thus, the epoxy-coated Cr alloy steel has greater corrosion resistance in a chloride-containing environment than the carbon steel. Hence, epoxy-coated Cr alloy steel can be successfully used as a construction material in structures.

  18. Influence of Portland Cement Class on the Corrosion Rate of Steel Reinforcement in Cement Mortar Caused by Penetrating Chloride and Sulfate from the Environment

    OpenAIRE

    Bikić, F.; Cacan, M.; Rizvanović, M.

    2013-01-01

    The influence of portland cement class on the corrosion rate of steel reinforcement in cement mortar caused by penetrating chloride or sulfate from the environment in already hardened cement mortar is investigated in this paper. Three classes of portland cement have been used for the tests, PC 35, PC 45 and PC 55. Cylindrical samples of cement mortar with steel reinfor- cement in the middle were treated 6 months at room temperature in the follow...

  19. Effect of Chloride on Tensile and Bending Capacities of Basalt FRP Mesh Reinforced Cementitious Thin Plates under Indoor and Marine Environments

    Directory of Open Access Journals (Sweden)

    Yan Xie

    2016-01-01

    Full Text Available This paper presented a durability experimental study for thin basalt fiber reinforced polymer (BFRP mesh reinforced cementitious plates under indoor and marine environment. The marine environment was simulated by wetting/drying cycles (wetting in salt water and drying in hot air. After 12 months of exposure, the effects of the chloride on the tensile and bending behaviors of the thin plate were investigated. In addition to the penetration of salt water, the chloride in the thin plate could be also from the sea sand since it is a component of the plate. Experimental results showed that the effect of the indoor exposure on the tensile capacity of the plate is not pronounced, while the marine exposure reduced the tensile capacity significantly. The bending capacity of the thin plates was remarkably reduced by both indoor and marine environmental exposure, in which the effect of the marine environment is more severe. The tensile capacity of the meshes extracted from the thin plates was tested, as well as the meshes immersed in salt solution for 30, 60, and 90 days. The test results confirmed that the chloride is the reason of the BFRP mesh deterioration. Moreover, as a comparison, the steel mesh reinforced thin plate was also tested and it has a similar durability performance.

  20. 40 CFR 61.65 - Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... dichloride, vinyl chloride and polyvinyl chloride plants. 61.65 Section 61.65 Protection of Environment... AIR POLLUTANTS National Emission Standard for Vinyl Chloride § 61.65 Emission standard for ethylene dichloride, vinyl chloride and polyvinyl chloride plants. An owner or operator of an ethylene...

  1. Alcohol solutions of triphenyl-tetrazolium chloride as high-dose radiochromic dosimeters

    Energy Technology Data Exchange (ETDEWEB)

    Kovacs, A.; Wojnarovits, L.; El-Assy, N.B.; Afeefy, H.Y.; Al-Sheikhly, M.; Walker, M.L.; McLaughlin, W.L. [National Inst. of Standards and Technology (NML), Gaithersburg, MD (United States). Ionizing Radiation Div.

    1995-10-01

    The radiolytic reduction of colorless tetrazolium salts in aqueous solution to the highly colored formazan dye is a well-known acid-forming radiation chemical reaction. Radiochromic thin films and three-dimensional hydrocolloid gels have been used for imaging and mapping absorbed dose distributions. The high solubility of 2,3,5-triphenyl-tetrazolium chloride (TTC) in alcohols provides a useful liquid dosimeter (45 mM TTC in aerated ethanol) and shows a linear response of absorbance increase ({lambda}{sub max} = 480 nm) with dose over the range 1-16 kGy. The linear molar absorption coefficient ({epsilon}{sub m}) for the formazan at the absorption peak is 1.5 x 10{sup 3} m{sup 2} mol{sup -1}, and the radiation chemical yield for the above solution is G (formazan) 0.014 {mu}mol J{sup -1}. The irradiation temperature coefficient is about 0.8 percent per degree Celsius rise in temperature over the temperature range 0-30 {sup o}C but is much larger between 30{sup o} and 60 {sup o}C. The unirradiated and irradiated solutions are stable over at least five days storage at normal laboratory temperature in the dark, but when stored in daylight at elevated temperature, the unirradiated solution in sealed amber glass ampoules undergoes slow photolytic dye formation, and the irradiated solution experiences initial fading and subsequent reversal (photochromism) when exposed to direct sunlight. (author).

  2. Standard test method for determining effects of chemical admixtures on corrosion of embedded steel reinforcement in concrete exposed to chloride environments

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2007-01-01

    1.1 This test method covers a procedure for determining the effects of chemical admixtures on the corrosion of metals in concrete. This test method can be used to evaluate materials intended to inhibit chloride-induced corrosion of steel in concrete. It can also be used to evaluate the corrosivity of admixtures in a chloride environment. 1.2 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  3. Tribenzylammonium chloride

    Directory of Open Access Journals (Sweden)

    Waly Diallo

    2014-05-01

    Full Text Available Single crystals of the title salt, C21H21NH+·Cl−, were isolated as a side product from the reaction involving [(C6H5CH23NH]2[HPO4] and Sn(CH33Cl in ethanol. Both the cation and the anion are situated on a threefold rotation axis. The central N atom in the cation has a slightly distorted tetrahedral environment, with angles ranging from 107.7 to 111.16 (10°. In the crystal, the tribenzylammonium cations and chloride anions are linked through N—H...Cl and C—H...Cl hydrogen bonds, leading to the formation of infinite chains along [001]. The crystal studied was a merohedral twin.

  4. Highly ordered cellulose II crystalline regenerated from cellulose hydrolyzed by 1-butyl-3-methylimidazolium chloride.

    Science.gov (United States)

    Ahn, Yongjun; Song, Younghan; Kwak, Seung-Yeop; Kim, Hyungsup

    2016-02-10

    This research focused on the preparation of highly ordered cellulose II crystalline by cellulose hydrolysis in ionic liquid, and the influence of molecular mobility on recrystallization of cellulose. The molar mass of cellulose was controlled by hydrolysis using 1-butyl-3-methylimidazolium chloride (BmimCl). The molecular mobility of cellulose dissolved in BmimCl was characterized by rheological properties. After characterization of cellulose solution and regeneration, change of molar mass and conversion to crystalline were monitored using gel-permeation chromatography and powder X-ray diffraction, respectively. The molar mass of the cellulose in BmimCl was remarkably decreased with an increase in duration time, resulting in better mobility and a lower conformational constraint below critical molar mass. The decrease in molar mass surprisingly increased the crystallinity up to ∼ 85%, suggesting a recrystallization rate dependence of the mobility. The correlation between the mobility and recrystallization rate represented quit different behavior above and below a critical molar mass, which strongly demonstrated to the effect of mobility on the conversion of amorphous state to crystalline structure.

  5. Determination of Benzalkonium Chloride in Nasal Drops by High-Performance Liquid Chromatography

    Directory of Open Access Journals (Sweden)

    Danijela A. Kostić

    2012-01-01

    Full Text Available A high-performance liquid chromatography (HPLC system was used in the reversed phase mode for the determination of benzalkonium chloride (BKC in nosal drops. A Chromolit RP-18e, 100 x 4.6, (UM6077/035 column was used at 40 °C. The mobile phase, optimized through an experimental design, was a 70:30 (v/v mixture of 0.057M Na-heksansulphonate potassium, dihydrogen orthophosphate buffer (pH 2.9 and acetonitrile, pumped at a flow rate of 1.75 mL/min at maintaining column temperature at 40 °C. Maximum UV detection was achieved at 215 nm. The method was validated in terms of selectivity, linearity, repeatability, precision and accuracy. The method was successfully applied for the determination of BKC in a pharmaceutical formulation of nasal drop solution without any interference from common excipients and drug substance. All the validation parameters were within the acceptance range, concordant to ICH guidelines.

  6. Determination of benzalkonium chloride in viscous ophthalmic drops of azithromycin by high-performance liquid chromatography *

    Science.gov (United States)

    Shen, Yan; Xu, Sheng-jie; Wang, Shi-chun; Tu, Jia-sheng

    2009-01-01

    A high-performance liquid chromatography (HPLC) system was used in the reversed phase mode for the determination of benzalkonium chloride (BKC) in azithromycin viscous ophthalmic drops. A Venusil-XBP(L)-C18 (150 mm×4.6 mm, 5 μm) column was used at 50 °C. The mobile phase consisted of a mixture of methanol-potassium phosphate (16:5, v/v). Two sample preparation methods were compared. The results suggested that, compared with an extraction procedure, a deproteinization procedure was much quicker and more convenient. Using the deproteinization procedure for sample preparation, calibration curves were linear in the range 5.0~50 μg/ml. The within-day and inter-day coefficients of variation were less than 10%. The average recoveries were determined as 96.70%, 98.52%, and 97.96% at concentrations of 10.0, 30.0, and 50.0 μg/ml, respectively. Variability in precision did not exceed 5%. In conclusion, this HPLC method using a simple sample treatment procedure appears suitable for monitoring BKC content in azithromycin viscous ophthalmic drops. PMID:19946951

  7. An Accelerated Test Method of Simultaneous Carbonation and Chloride Ion Ingress: Durability of Silica Fume Concrete in Severe Environments

    Directory of Open Access Journals (Sweden)

    S. A. Ghahari

    2016-01-01

    Full Text Available The effects of simultaneous carbonation and chloride ion attack on mechanical characteristics and durability of concrete containing silica fume have been investigated through an accelerated test method. Specimens containing different amounts of silica fume were maintained in an apparatus in which carbon dioxide pressure and concentration and relative humidity were kept constant, and wetting and drying cycles in saline water were applied. Surface resistivity, sorptivity, CO2 consumption, and carbonation and chloride ion ingress depths measurements were taken. Phase change due to carbonation and chloride ion attack was monitored by XRD analysis, and microstructures and interfacial transition zones were studied by implementing SEM as well as mercury intrusion porosimetry. It was expected to have a synergistic effect in the tidal zone where simultaneous carbonation and chloride ion attack happen. However, the observed reduced surface resistivity, compared to specimens maintained in CO2 gas, could be due to the moisture that is available near the surface, hindering CO2 from penetrating into the pores of the specimens. Moreover, the porosity analysis of the specimens showed that the sample containing silica fume cured in the tidal zone had 50.1% less total porosity than the plain cement paste cured in the same condition.

  8. Effects of slag and fly ash on reinforcement corrosion in concrete in chloride environment: Research from the Netherlands

    NARCIS (Netherlands)

    Polder, R.B.

    2012-01-01

    A review is given of research on the durability performance of concrete made with blast furnace slag and fly ash related to chloride induced reinforcement corrosion, carried out in the Netherlands, where slag has been used in cement for almost a century. Results are presented from field studies on c

  9. Effects of slag and fly ash on reinforcement corrosion in concrete in chloride environment. Research from the Netherlands

    NARCIS (Netherlands)

    Polder, R.B.

    2012-01-01

    A review is given of research on the durability performance of concrete made with blast furnace slag and fly ash related to chloride induced reinforcement corrosion, carried out in the Netherlands, where slag has been used in cement for almost a century. Results are presented from field studies on c

  10. Intergranular stress corrosion cracking of welded ferritic stainless steels in high temperature aqueous environments

    Energy Technology Data Exchange (ETDEWEB)

    Fukuzuka, Toshio; Shimogori, Kazutoshi; Fujiwara, Kazuo; Tomari, Haruo (Kobe Steel Ltd. (Japan). Central Research and Development Lab.); Kanda, Masao

    1982-07-01

    In considering the application of ferritic stainless steels to heat exchanger tubing materials for moisture separator-reheaters in LWRs, the effects of environmental conditions (temperature, chloride, dissolved oxygen, pH), thermal history, and steel composition (content of C, N, Cr and Ti) on the Inter-Granular Stress Corrosion Cracking (IGSCC) in high temperature aqueous environments, were studied. The IGSCC was proved to depend on steel composition and thermal history rather than environment. From these results, a steel was designed to prevent IGSCC of the welding HAZ for 18Cr and 13Cr steels.

  11. DEVELOPMENT OF DISPOSABLE SORBENTS FOR CHLORIDE REMOVAL FROM HIGH TEMPERATURE COAL-DERIVED GASES

    Energy Technology Data Exchange (ETDEWEB)

    Gopala Krishnan; Raghubir Gupta

    1999-09-01

    Advanced integrated-gasification combined-cycle (IGCC) and integrated-gasification fuel cell (IGFC) systems require the development of high temperature sorbents for the removal of hydrogen chloride (HCl) vapor to less than 1 parts-per-million (ppm) levels. HCl is a highly reactive, corrosive, and toxic gas which must be removed to meet environmental regulations, to protect power generation equipment, and to minimize deterioration of hot gas desulfurization sorbents. The objective of this program was to develop disposable, alkali-based sorbents capable of reducing HCl vapor levels to less than 1 ppm in the temperature range from 400 to 750 C and pressures in the range from 1 to 20 atm. The primary areas of focus of this program were to investigate different methods of sorbent fabrication, testing their suitability for different reactor configurations, obtaining reaction kinetics data, and conducting a preliminary economic feasibility assessment. This program was a joint effort between SRI International (SRI), Research Triangle Institute (RTI), and General Electric Corporate Research and Development (GE-CRD). SRI, the prime contractor and RTI, a major subcontractor, performed most of the work in this program. Thermochemical calculations indicated that sodium-based sorbents were capable of reducing HCl vapor levels to less than 1 ppm at temperatures up to 650 C, but the regeneration of spent sorbents would require complex process steps. Nahcolite (NaHCO{sub 3}), a naturally-occurring mineral, could be used as an inexpensive sorbent to remove HCl vapor in hot coal gas streams. In the current program, nahcolite powder was used to fabricate pellets suitable for fixed-bed reactors and granules suitable for fluidized-bed reactors. Pilot-scale equipment were used to prepare sorbents in large batches: pellets by disk pelletization and extrusion techniques, and granules by granulation and spray-drying techniques. Bench-scale fixed- and fluidized-bed reactors were assembled at

  12. Chloride channels in stellate cells are essential for uniquely high secretion rates in neuropeptide-stimulated Drosophila diuresis.

    Science.gov (United States)

    Cabrero, Pablo; Terhzaz, Selim; Romero, Michael F; Davies, Shireen A; Blumenthal, Edward M; Dow, Julian A T

    2014-09-30

    Epithelia frequently segregate transport processes to specific cell types, presumably for improved efficiency and control. The molecular players underlying this functional specialization are of particular interest. In Drosophila, the renal (Malpighian) tubule displays the highest per-cell transport rates known and has two main secretory cell types, principal and stellate. Electrogenic cation transport is known to reside in the principal cells, whereas stellate cells control the anion conductance, but by an as-yet-undefined route. Here, we resolve this issue by showing that a plasma membrane chloride channel, encoded by ClC-a, is exclusively expressed in the stellate cell and is required for Drosophila kinin-mediated induction of diuresis and chloride shunt conductance, evidenced by chloride ion movement through the stellate cells, leading to depolarization of the transepithelial potential. By contrast, ClC-a knockdown had no impact on resting secretion levels. Knockdown of a second CLC gene showing highly abundant expression in adult Malpighian tubules, ClC-c, did not impact depolarization of transepithelial potential after kinin stimulation. Therefore, the diuretic action of kinin in Drosophila can be explained by an increase in ClC-a-mediated chloride conductance, over and above a resting fluid transport level that relies on other (ClC-a-independent) mechanisms or routes. This key segregation of cation and anion transport could explain the extraordinary fluid transport rates displayed by some epithelia.

  13. Factors influencing chloride deposition in a coastal hilly area and application to chloride deposition mapping

    Directory of Open Access Journals (Sweden)

    H. Guan

    2009-09-01

    Full Text Available Chloride is commonly used as an environmental tracer for studying water flow and solute transport in the environment. It is especially useful for estimating groundwater recharge based on the commonly used chloride mass balance (CMB method. Strong spatial variability in chloride deposition in coastal areas is one difficulty encountered in appropriately applying the CMB approach. Furthermore, intensive vegetation clearance for agriculture, for example during the European settlement in many coastal areas of Australia, may have perturbed catchment chloride balance conditions for appropriate use in CMB applications. In order to deal with these issues, a high resolution chloride deposition map in the coastal region is needed. In this study, we examined geographic, orographic, and atmospheric factors influencing chloride deposition in the Mount Lofty Ranges (MLR, a coastal hilly area of approximately 9000 km2 spatial extent in South Australia, using partial correlation and regression analyses. The results indicate that coastal distance, and terrain aspect and slope are two most significant factors controlling chloride deposition. Coastal distance accounts for 65% spatial variability in chloride deposition, with terrain aspect and slope for 8%. The deposition gradient is about 0.08 gm-2 year-1 km-1 as one progresses inland. The results are incorporated into a published de-trended residual kriging approach (ASOADeK to produce a 1 km×1 km resolution annual chloride deposition map and a bulk precipitation chloride concentration map. The average uncertainty of the deposition map is about 30% in the western MLR, and over 50% in the eastern MLR. The maps will form a very useful basis for examining catchment chloride balances for use in the CMB application in the study area.

  14. Synthesis of Macrocyclic Ionophore for the Development of Highly Selective Chloride Sensor

    Directory of Open Access Journals (Sweden)

    Sameena Mehtab

    2015-03-01

    Full Text Available The macrocyclic ligands 3,8,12,17-tetramethyl-2,18,9,11-bipyridyl-1,4,7,10,13,16-hexaazacyclooctadecanetetrahydro bromide has been synthesized and explored as suitable ionophores for chloride selective membrane sensors. It displays Nernstian behavior (59.2 mV decade-1 across the range of 4.1 × 10-8 to 1.0 × 10-2 M. The detection limit of the electrode is ~ 15 nM and the response time and life times are 14 s and eight weeks respectively over a wide pH range (3.5 - 9.5. Interference from other anions is very low and it can be used as indicator electrode in the potentiometric titration of chloride ions and to determine chloride in agricultural soil water samples.

  15. Study on Treatment of acidic and highly concentrated fluoride waste water using calcium oxide-calcium chloride

    Science.gov (United States)

    Ren, T.; Gao, X. R.; Zheng, T.; Wang, P.

    2016-08-01

    There are problems with treating acidic waste water containing high concentration fluorine by chemical precipitation, including the low sludge setting velocity and the high difficulty of reaching the criterion. In Heilongjiang province, a graphite factory producing high-purity graphite generates acidic waste water with a high concentration of fluorine. In this paper, the effect of removals on the concentration of fluoride with the combined treatment of calcium oxide and calcium chloride were discussed with regard to acid waste water. The study improved the sludge characteristics by using polyacrylamide (PAM) and polymeric aluminum chloride (PAC). The effect of different coagulants on sludge was evaluated by the sludge settlement ratio (SV), sludge volume index (SVI) and sludge moisture content. The results showed that the optimal combination for 100 ml waste water was calcium oxide addition amount of 14 g, a calcium chloride addition amount of 2.5 g, a PAM addition amount of 350 mg/L, and the effluent fluoride concentration was below 6 mg/L. PAM significantly improved the sludge settling velocity. The sludge settlement ratio reduced from 87.6% to 60%. The process for wastewater treatment was easily operated and involved low expenditure.

  16. Highly efficient synthesis of phenols by copper-catalyzed hydroxylation of aryl iodides, bromides, and chlorides.

    Science.gov (United States)

    Yang, Kai; Li, Zheng; Wang, Zhaoyang; Yao, Zhiyi; Jiang, Sheng

    2011-08-19

    8-Hydroxyquinolin-N-oxide was found to be a very efficient ligand for the copper-catalyzed hydroxylation of aryl iodides, aryl bromides, or aryl chlorides under mild reaction conditions. This methodology provides a direct transformation of aryl halides to phenols and to alkyl aryl ethers. The inexpensive catalytic system showed great functional group tolerance and excellent selectivity. © 2011 American Chemical Society

  17. Modeling of the Migration of Glycerol Monoester Plasticizers in Highly Plasticized Poly(vinyl chloride)

    DEFF Research Database (Denmark)

    Lundsgaard, Rasmus; Kontogeorgis, Georgios; Kristiansen, Jørgen K.;

    2009-01-01

    soybean oil (ESBO) with regard to their migration from three different types of poly(vinyl chloride) into isooctane at 20, 40, and 60 degrees C. Diffusion coefficients derived from the experimental migration data were evaluated against diffusion coefficients estimated from a model based solely...

  18. Geopolymer encapsulation of a chloride salt phase change material for high temperature thermal energy storage

    Science.gov (United States)

    Jacob, Rhys; Trout, Neil; Raud, Ralf; Clarke, Stephen; Steinberg, Theodore A.; Saman, Wasim; Bruno, Frank

    2016-05-01

    In an effort to reduce the cost and increase the material compatibility of encapsulated phase change materials (EPCMs) a new encapsulated system has been proposed. In the current study a molten salt eutectic of barium chloride (53% wt.), potassium chloride (28% wt.) and sodium chloride (19% wt.) has been identified as a promising candidate for low cost EPCM storage systems. The latent heat, melting point and thermal stability of the phase change material (PCM) was determined by DSC and was found to be in good agreement with results published in the literature. To cope with the corrosive nature of the PCM, it was decided that a fly-ash based geopolymer met the thermal and economic constraints for encapsulation. The thermal stability of the geopolymer shell was also tested with several formulations proving to form a stable shell for the chosen PCM at 200°C and/or 600°C. Lastly several capsules of the geopolymer shell with a chloride PCM were fabricated using a variety of methods with several samples remaining stable after exposure to 600°C testing.

  19. Galaxy interactions II: High density environments

    CERN Document Server

    Alonso, Sol; Padilla, Nelson; Lambas, Diego G

    2011-01-01

    With the aim to assess the role of dense environments in galaxy interactions, properties we present an analysis of close galaxy pairs in groups and clusters, obtained from the Sloan Digital Sky Survey Data Release 7 (SDSS-DR7). We identified pairs that reside in groups by cross-correlating the total galaxy pair catalogue with the SDSS-DR7 group catalogue from Zapata et al. (2009). We classify pair galaxies according to the intensity of interaction. We analysed the effect of high density environments on different classes of galaxy-galaxy interactions and we have also studied the impact of the group global environment on pair galaxies. We find that galaxy pairs are more concentrated towards the group centres with respect to the other group galaxy members, and disturbed pairs show a preference to contain the brightest galaxy in the groups. The color-magnitude relation exhibits significant differences between pair galaxies and the control sample, consisting in color tails with a clear excess of extremely blue and...

  20. Corrosion and runoff rates of Cu and three Cu-alloys in marine environments with increasing chloride deposition rate.

    Science.gov (United States)

    Odnevall Wallinder, Inger; Zhang, Xian; Goidanich, Sara; Le Bozec, Nathalie; Herting, Gunilla; Leygraf, Christofer

    2014-02-15

    Bare copper sheet and three commercial Cu-based alloys, Cu15Zn, Cu4Sn and Cu5Al5Zn, have been exposed to four test sites in Brest, France, with strongly varying chloride deposition rates. The corrosion rates of all four materials decrease continuously with distance from the coast, i.e. with decreasing chloride load, and in the following order: Cu4Sn>Cu sheet>Cu15Zn>Cu5Al5Zn. The patina on all materials was composed of two main layers, Cu2O as the inner layer and Cu2(OH)3Cl as the outer layer, and with a discontinuous presence of CuCl in between. Additional minor patina constituents are SnO2 (Cu4Sn), Zn5(OH)6(CO3)2 (Cu15Zn and Cu5Al5Zn) and Zn6Al2(OH)16CO3·4H2O/Zn2Al(OH)6Cl·2H2O/Zn5Cl2(OH)8·H2O and Al2O3 (Cu5Al5Zn). The observed Zn- and Zn/Al-containing corrosion products might be important factors for the lower sensitivity of Cu15Zn and Cu5Al5Zn against chloride-induced atmospheric corrosion compared with Cu sheet and Cu4Sn. Decreasing corrosion rates with exposure time were observed for all materials and chloride loads and attributed to an improved adherence with time of the outer patina to the underlying inner oxide. Flaking of the outer patina layer was mainly observed on Cu4Sn and Cu sheet and associated with the gradual transformation of CuCl to Cu2(OH)3Cl of larger volume. After three years only Cu5Al5Zn remains lustrous because of a patina compared with the other materials that appeared brownish-reddish. Significantly lower release rates of metals compared with corresponding corrosion rates were observed for all materials. Very similar release rates of copper from all four materials were observed during the fifth year of marine exposure due to an outer surface patina that with time revealed similar constituents and solubility properties. Copyright © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

  1. High dietary sodium chloride causes further protein loss during head-down tilt bed rest (HDBR)

    Science.gov (United States)

    Buehlmeier, Judith; Frings-Meuthen, Petra; Baecker, Natalie; Stehle, Peter; Heer, Martina

    Human spaceflight is associated with a loss of body protein most likely caused by muscle degradation. Additionally astronauts tend towards a high dietary intake of sodium chloride (NaCl), which has recently been shown to induce low grade metabolic acidosis (Frings-Meuthen et al. JBMR, Epub 2007). In several patterns, e.g. chronical renal failure, metabolic acidosis is associated with protein catabolism. We therefore hypothesized that high dietary intake of NaCl enforces protein losses in HDBR, a model for physiological changes in microgravity (µG). Eight healthy male subjects (mean age 26.25 ± 3.5; mean body weight: 78.5 ± 4.1 kg) participated in a 14-day bed rest study in the metabolic ward of the DLR - Institute of Aerospace Medicine, Cologne, Germany. The study was carried out in a cross over design, consisting of two phases, each lasting 22 days (5 days adaptation, 14 days 6° HDBR and 3 days recovery). Both study phases were identical with respect to environmental conditions and study protocol. Subjects received an individually tailored, weight-maintaining diet containing 1.3 g protein/kg/day. The diet was identical in both study phases with the exception of NaClintake: Every subject received a low NaCl diet (0.7 mmol/kg/day) in one phase and a high NaCl diet (7.7 mmol/kg/day) in another one. Blood gas for analysis of acid-base balance was implemented at days 4 and 5 of adaptation, days 2, 5, 7, 10, 12, 14 of HDBR and days 2, 3 of recovery. Continuous urine collection started on the first day in the metabolic ward to analyze nitrogen excretion. Nitrogen balance was calculated from the difference between protein intake and urinary nitrogen excretion, determined by use of chemiluminescence (Grimble et al. JPEN, 1988). Plasma pH did not change significantly (p=0.285), but plasma bicarbonate and base excess decreased (p=0.0175; p=0.0093) with high NaCl intake in HDBR compared to the low NaCl diet. Nitrogen balance in HDBR was negative, as expected in

  2. Zirconyl chloride promoted highly efficient solid phase synthesis of amide derivatives

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    An efficient solid phase route for the synthesis of amide derivatives by the reaction of carboxylic acids with urea in the presence of catalytic amount of zirconyl chloride under microwave irradiation conditions was described. In this way, a range of interesting amide derivatives was obtained in good to excellent yields. The catalyst was recycled with fresh reactants and it gave almost similar results without significant loss of activity up to the third run.

  3. 氯盐环境下开裂混凝土耐久性研究进展%Research Progress on Durability of Cracked Concrete Under Chloride Environment

    Institute of Scientific and Technical Information of China (English)

    延永东; 姚昌建; 刘荣桂; 陆春华

    2015-01-01

    To reveal the influence of crack on durability of reinforced concrete structure under chloride environment ,authors analyzed the change rules about durability of concrete with load cracks ,non‐load cracks and artificial cracks by combining the existed references .T he effects of crack type (artificial or natural crack ) ,width ,depth and distance on concrete durability w hich contains penetrability ,chloride ingression and steel corrosion were pointed out . The models about chloride ion transportation in cracked concrete under saturated and unsaturated state were also introduced .The basic conclusions and key points needed in further study were finally put forward .The obtained results can be served as references for the future research on durability of cracked concretes under chloride environment .%为了明确裂缝对氯盐环境下钢筋混凝土结构耐久性的影响,结合已有文献分析了荷载裂缝、非荷载裂缝及预制裂缝下混凝土结构在氯盐环境下的耐久性变化规律,指出了裂缝形式(人工裂缝、自然裂缝)、宽度、深度、间距等参数对混凝土渗透性及氯离子传输、内部钢筋锈蚀的影响规律,介绍了已有的饱和与非饱和状态下开裂混凝土内氯离子传输过程的模型,指出了氯盐环境下开裂混凝土耐久性研究已得出的基本结论及需要深入研究的方面。所得结论可为氯盐环境下开裂混凝土的后期研究提供借鉴。

  4. EFFECT OF CHLORIDE ON THE ATMOSPHERIC CORROSION OF SIMULATED ARTIFACT IRON IN NO3-BEARING POLLUTANT ENVIRONMENT

    Institute of Scientific and Technical Information of China (English)

    X. Cao; C.C. Xu

    2006-01-01

    The effect of chloride in nitrogen-bearing pollutant on the atmospheric corrosion of cast iron was investigated by using periodic wet-dry test, electrochemical experiment and surface tension test.Scanning electron microscopy (SEM) with energy disperse atomic X-ray (EDAX) was used to identify the corrosion processes and products. The results of the weight loss measurement showed that the whole corrosion kinetics can be approximately described by: AW=AtB. With the addition of NaC1, B increases. The result presented that Cl- accelerated the corrosion rate obviously during the whole corrosion process. The initial corrosion process was investigated from the viewpoint of surface tension. At the initial corrosion period, the corrosion rate was proportion to the adsorption of anions contained the solutions. And as corrosion went on, the penetration effect of anions and different characteristics of the corrosion products began to dominant the corrosion process, which led to the accelerated effect.

  5. Oxidative stress and the high altitude environment

    Directory of Open Access Journals (Sweden)

    Jakub Krzeszowiak

    2013-03-01

    Full Text Available In the recent years there has been considerable interest in mountain sports, including mountaineering, owing to the general availability of climbing clothing and equipment as well trainings and professional literature. This raised a new question for the environmental and mountain medicine: Is mountaineering harmful to health? Potential hazards include the conditions existing in the alpine environment, i.e. lower atmospheric pressure leading to the development of hypobaric hypoxia, extreme physical effort, increased UV radiation, lack of access to fresh food, and mental stress. A reasonable measure of harmfulness of these factors is to determine the increase in the level of oxidative stress. Alpine environment can stimulate the antioxidant enzyme system but under specific circumstances it may exceed its capabilities with simultaneous consumption of low-molecular antioxidants resulting in increased generation of reactive oxygen species (ROS. This situation is referred to as oxidative stress. Rapid and uncontrolled proliferation of reactive oxygen species leads to a number of adverse changes, resulting in the above-average damage to the lipid structures of cell membranes (peroxidation, proteins (denaturation, and nucleic acids. Such situation within the human body cannot take place without resultant systemic consequences. This explains the malaise of people returning from high altitude and a marked decrease in their physical fitness. In addition, a theory is put forward that the increase in the level of oxidative stress is one of the factors responsible for the onset of acute mountain sickness (AMS. However, such statement requires further investigation because the currently available literature is inconclusive. This article presents the causes and effects of development of oxidative stress in the high mountains.

  6. Reserve lithium-thionyl chloride battery for high rate extended mission applications

    Science.gov (United States)

    Peabody, Mark; Brown, Robert A.

    An effort has been made to develop technology for lithium-thionyl chloride batteries whose emission times will extend beyond 20 min and whose power levels will be in excess of 1800 W, using the requirements for an existing silver-zinc battery's electrical requirements as a baseline. The target design encompasses separate 31- and 76-V sections; the design goal was the reduction of battery weight to 50 percent that of the present silver/zinc cell. A cell has been achieved whose mission can be conducted without container heat losses.

  7. High glucose inhibits ClC-2 chloride channels and attenuates cell migration of rat keratinocytes

    Directory of Open Access Journals (Sweden)

    Pan F

    2015-08-01

    Full Text Available Fuqiang Pan, Rui Guo, Wenguang Cheng, Linlin Chai, Wenping Wang, Chuan Cao, Shirong LiDepartment of Plastic and Reconstructive Surgery, Southwestern Hospital, Third Military Medical University, Chongqing, People’s Republic of China Background: Accumulating evidence has demonstrated that migration of keratinocytes is critical to wound epithelialization, and defects of this function result in chronic delayed-healing wounds in diabetes mellitus patients, and the migration has been proved to be associated with volume-activated chloride channels. The aim of the study is to investigate the effects of high glucose (HG, 25 mM on ClC-2 chloride channels and cell migration of keratinocytes.Methods: Newborn Sprague Dawley rats were used to isolate and culture the keratinocyte in this study. Immunofluorescence assay, real-time polymerase chain reaction, and Western blot assay were used to examine the expression of ClC-2 protein or mRNA. Scratch wound assay was used to measure the migratory ability of keratinocytes. Transwell cell migration assay was used to measure the invasion and migration of keratinocytes. Recombinant lentivirus vectors were established and transducted to keratinocytes. Whole-cell patch clamp was used to perform the electrophysiological studies.Results: We found that the expression of ClC-2 was significantly inhibited when keratinocytes were exposed to a HG (25 mM medium, accompanied by the decline of volume-activated Cl- current (ICl,vol, migration potential, and phosphorylated PI3K as compared to control group. When knockdown of ClC-2 by RNAi or pretreatment with wortmannin, similar results were observed, including ICl,vol and migration keratinocytes were inhibited.Conclusion: Our study proved that HG inhibited ClC-2 chloride channels and attenuated cell migration of rat keratinocytes via inhibiting PI3K signaling.Keywords: high glucose, keratinocytes, ClC-2, cell migration, PI3K

  8. Solid oxide fuel cell anode degradation by the effect of hydrogen chloride in stack and single cell environments

    Science.gov (United States)

    Madi, Hossein; Lanzini, Andrea; Papurello, Davide; Diethelm, Stefan; Ludwig, Christian; Santarelli, Massimo; Van herle, Jan

    2016-09-01

    The poisoning effect by hydrogen chloride (HCl) on state-of-the-art Ni anode-supported solid oxide fuel cells (SOFCs) at 750 °C is evaluated in either hydrogen or syngas fuel. Experiments are performed on single cells and short stacks and HCl concentration in the fuel gas is increased from 1 ppm(v) up to 1000 ppm(v) at different current densities. Characterization methods such as cell voltage monitoring vs. time and electrochemical impedance response analysis (distribution of relaxation times (DRT), equivalent electrical circuit) are used to identify the prevailing degradation mechanism. Single cell experiments revealed that the poisoning is more severe when feeding with hydrogen than with syngas. Performance loss is attributed to the effects of HCl adsorption onto nickel surfaces, which lowered the catalyst activity. Interestingly, in syngas HCl does not affect stack performance even at concentrations up to 500 ppm(v), even when causing severe corrosion of the anode exhaust pipe. Furthermore, post-test analysis suggests that chlorine is present on the nickel particles in the form of adsorbed chlorine, rather than forming a secondary phase of nickel chlorine.

  9. Cesium hafnium chloride: A high light yield, non-hygroscopic cubic crystal scintillator for gamma spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Burger, Arnold, E-mail: aburger@fisk.edu [Department of Life and Physical Sciences, Fisk University, Nashville, Tennessee 37208 (United States); Department of Physics and Astronomy, Vanderbilt University, Nashville, Tennessee 37235 (United States); Rowe, Emmanuel; Groza, Michael; Morales Figueroa, Kristle [Department of Life and Physical Sciences, Fisk University, Nashville, Tennessee 37208 (United States); Cherepy, Nerine J.; Beck, Patrick R.; Hunter, Steven; Payne, Stephen A. [Lawrence Livermore National Laboratory, Livermore, California 94550 (United States)

    2015-10-05

    We report on the scintillation properties of Cs{sub 2}HfCl{sub 6} (cesium hafnium chloride or CHC) as an example of a little-known class of non-hygroscopic compounds having the generic cubic crystal structure of K{sub 2}PtCl{sub 6}. The crystals are easily growable from the melt using the Bridgman method with minimal precursor treatments or purification. CHC scintillation is centered at 400 nm, with a principal decay time of 4.37 μs and a light yield of up to 54 000 photons/MeV when measured using a silicon CCD photodetector. The light yield is the highest ever reported for an undoped crystal, and CHC also exhibits excellent light yield nonproportionality. These desirable properties allowed us to build and test CHC gamma-ray spectrometers providing energy resolution of 3.3% at 662 keV.

  10. Novel Highly Flexible Wormlike Micelles Formed by Cetylpyridinium Chloride and Trioxyethylene Monododecyl Ether Surfactants

    Directory of Open Access Journals (Sweden)

    Firoz Kapadia

    2014-06-01

    Full Text Available The impact of small nonionic hydrophobic molecule, trioxyethylene monododecyl ether (C12EO3, on the viscoelastic properties of aqueous solutions of cetylpyridinium chloride (CPC is studied. As the C12EO3 concentration increases, the viscosity passes through a maximum. Dynamic rheological measurements revealed a comprehensive picture of how C12EO3 affects the different length scales in the entangled wormlike micelles. Increase in the viscosity can normally be caused by insertion of amphiphilic C12EO3 molecules into the cationic surfactant (CPC layer, or micellar swelling, caused by solubilization of very hydrophobic molecules in the micellar core. The partial phase behavior and rheology of this mixed surfactant systems is studied.

  11. Ionic liquid-polyvinyl chloride ionomer for highly selective isolation of basic proteins.

    Science.gov (United States)

    Shu, Yang; Chen, Xu-Wei; Wang, Jian-Hua

    2010-04-15

    Hydrophilic ionic liquid-polyvinyl chloride (PVC) hybrids were prepared by immobilizing N-methylimidazole (N-mim) to PVC chains in toluene. The NmimCl-PVC hybrids were characterized by FT-IR, (1)H NMR, surface charge analysis and elemental analysis. The immobilization ratio, i.e., the percentage of chloride on PVC chain reacting with N-mim to form the hybrid, varies from 4.3% to 15.1% by increasing the N-mim/PVC molar ratio. The most distinct feature of the hybrid is its excellent selectivity for adsorbing basic proteins by effective suppression of the non-specific protein adsorption by pure PVC, and a higher immobilization ratio facilitates better selectivity. In Tris-HCl buffer, 100 microg mL(-1) of basic proteins, i.e., lysozyme (Lys), cytochrome c (cyt-c) and hemoglobin (Hb), were favorably adsorbed with efficiencies of 97%, 98% and 94% by the hybrid with an immobilization ratio of 15.1%, while the adsorption of acidic proteins, i.e., bovine albumin serum (BSA), transferring (Trf) and immunoglobulin G (IgG) were negligible. The retained Lys, cyt-c and Hb could be readily recovered by elution with phosphate buffer, carbonate buffer and SDS solution with efficiencies of 89%, 87% and 84%, respectively. Another feature of the hybrid is the significant improvement of the biocompatibility characterized by the maintenance of the activity of hemoglobin after adsorption and elution process. The practical usefulness of the hybrid was demonstrated by selective isolation of hemoglobin from human whole blood.

  12. Highly microporous carbons derived from a complex of glutamic acid and zinc chloride for use in supercapacitors

    Science.gov (United States)

    Dong, Xiao-Ling; Lu, An-Hui; He, Bin; Li, Wen-Cui

    2016-09-01

    The selection of carbon precursor is an important factor when designing carbon materials. In this study, a complex derived from L-glutamic acid and zinc chloride was used to prepare highly microporous carbons via facile pyrolysis. L-glutamic acid, a new carbon precursor with nitrogen functionality, coordinated with zinc chloride resulted in a homogeneous distribution of Zn2+ on the molecular level. During pyrolysis, the evaporation of the in situ formed zinc species creates an abundance of micropores together with the inert gases. The obtained carbons exhibit high specific surface area (SBET: 1203 m2 g-1) and a rich nitrogen content (4.52 wt%). In excess of 89% of the pore volume consists of micropores with pore size ranging from 0.5 to 1.2 nm. These carbons have been shown to be suitable for use as supercapacitor electrodes, and have been tested in 6 M KOH where a capacitance of 217 F g-1 was achieved at a current density of 0.5 A g-1. A long cycling life of 30 000 cycles was achieved at a current density of 1 A g-1, with only a 9% loss in capacity. The leakage current through a two-electrode device was measured as 2.3 μA per mg of electrode and the self-discharge characteristics were minimal.

  13. High Radiation Environment Nuclear Fragment Separator Magnet

    Energy Technology Data Exchange (ETDEWEB)

    Kahn, Stephen [Muons, Inc., Batavia, IL (United States); Gupta, Ramesh [Brookhaven National Lab. (BNL), Upton, NY (United States)

    2016-01-31

    Superconducting coils wound with HTS conductor can be used in magnets located in a high radiation environment. NbTi and Nb3Sn superconductors must operate at 4.5 K or below where removal of heat is less efficient. The HTS conductor can carry significant current at higher temperatures where the Carnot efficiency is significantly more favorable and where the coolant heat capacity is much larger. Using the HTS conductor the magnet can be operated at 40 K. This project examines the use of HTS conductor for the Michigan State University Facility For Rare Isotope Beams (FRIB) fragment separator dipole magnet which bends the beam by 30° and is located in a high radiation region that will not be easily accessible. Two of these magnets are needed to select the chosen isotope. There are a number of technical challenges to be addressed in the design of this magnet. The separator dipole is 2 m long and subtends a large angle. The magnet should keep a constant transverse field profile along its beam reference path. Winding coils with a curved inner segment is difficult as the conductor will tend to unwind during the process. In the Phase I project two approaches to winding the conductor were examined. The first was to wind the coils with curved sections on the inner and outer segments with the inner segment wound with negative curvature. The alternate approach was to use a straight segment on the inner segment to avoid negative curvature. In Phase I coils with a limited number of turns were successfully wound and tested at 77 K for both coil configurations. The Phase II program concentrated on the design, coil winding procedures, structural analysis, prototyping and testing of an HTS curved dipole coil at 40 K with a heat load representative of the radiation environment. One of the key criteria of the design of this magnet is to avoid the use of organic materials that would degrade rapidly in radiation. The Lorentz forces expected from the coils interacting with the

  14. Application of Tin(II Chloride Catalyst for High FFA Jatropha Oil Esterification in Continuous Reactive Distillation Column

    Directory of Open Access Journals (Sweden)

    Ratna Dewi Kusumaningtyas

    2016-03-01

    Full Text Available The application of heterogeneous solid acid catalysts in biodiesel production has become popular and gained significant attention over the last few years. It is since these types of catalysts hold the benefits in terms of easy separation from the product, reusability of the catalyst, high selectivity of the reaction. They are also considered sustainable and powerful particularly in organic synthesis. This work studied the use of tin(II chloride as solid Lewis acid catalyst to promote the esterification reaction of high Free Fatty Acid (FFA jatropha oil in continuous reactive distillation column. To obtain the optimum condition, the influences of reaction time, molar ratio of the reactant, and catalyst were investigated. It was revealed that the optimum condition was achieved at the molar ratio of methanol to FFA at 1:60, catalyst concentration of 5%, and reaction temperature of 60°C with the reaction conversion of 90%. This result was significantly superior to the identical reaction performed using batch reactor. The esterification of high FFA jatropha oil using reactive distillation in the presence of tin(II chloride provided higher conversion than that of Amberlyst-15 heterogeneous catalyst and was comparable to that of homogenous sulfuric acid catalyst, which showed 30 and 94.71% conversion, respectively. The esterification reaction of high FFA jatropha oil was subsequently followed by transesterification reaction for the completion of the biodiesel production. Transesterification was carried out at 60 °C, molar ratio of methanol to oil of 1:6, NaOH catalyst of 1%, and reaction time of one hour. The jatropha biodiesel product resulted from this two steps process could satisfy the ASTM and Indonesian biodiesel standard in terms of ester content (97.79 %, density, and viscosity. Copyright © 2016 BCREC GROUP. All rights reserved Received: 10th November 2015; Revised: 4th February 2016; Accepted: 4th February 2016 How to Cite: Kusumaningtyas

  15. Recovery of Iron from Pyrite Cinder Containing Non-ferrous Metals Using High-Temperature Chloridizing-Reduction-Magnetic Separation

    Science.gov (United States)

    Chen, Dong; Guo, Hongwei; Xu, Jifang; Lv, Yanan; Xu, Zemin; Huo, Haijiang

    2017-01-01

    This study presents a new technique that uses high-temperature chloridizing -reduction-magnetic separation to recover iron from pyrite cinder containing non-ferrous metals. The effects of the reduction temperature, reduction time, and chlorinating agent dosage were investigated. The optimized process parameters were proposed as the following: CaCl2 dosage of 2 pct, chloridizing at 1398 K (1125 °C) for 10 minutes, reducing at 1323 K (1050 °C) for 80 minutes, grinding to a particle size of 78.8 pct less than 45 μm, and magnetic field intensity of 73 mT. Under the optimized conditions, the Cu, Pb, and Zn removal rates were 45.2, 99.2, and 89.1 pct, respectively. The iron content of the magnetic concentrate was 90.6 pct, and the iron recovery rate was 94.8 pct. Furthermore, the reduction behavior and separation mechanism were determined based on microstructure and phase change analyses using X-ray powder diffraction, scanning electron microscope, and optical microscopy.

  16. NOvel Refractory Materials for High Alkali, High Temperature Environments

    Energy Technology Data Exchange (ETDEWEB)

    Hemrick, J.G.; Griffin, R. (MINTEQ International, Inc.)

    2011-08-30

    Refractory materials can be limited in their application by many factors including chemical reactions between the service environment and the refractory material, mechanical degradation of the refractory material by the service environment, temperature limitations on the use of a particular refractory material, and the inability to install or repair the refractory material in a cost effective manner or while the vessel was in service. The objective of this project was to address the need for new innovative refractory compositions by developing a family of novel MgO-Al2O3 spinel or other similar magnesia/alumina containing unshaped refractory composition (castables, gunnables, shotcretes, etc) utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques (in-situ phase formation, altered conversion temperatures, accelerated reactions, etc). This family of refractory compositions would then be tailored for use in high-temperature, highalkaline industrial environments like those found in the aluminum, chemical, forest products, glass, and steel industries. A research team was formed to carry out the proposed work led by Oak Ridge National Laboratory (ORNL) and was comprised of the academic institution Missouri University of Science and Technology (MS&T), and the industrial company MINTEQ International, Inc. (MINTEQ), along with representatives from the aluminum, chemical, glass, and forest products industries. The two goals of this project were to produce novel refractory compositions which will allow for improved energy efficiency and to develop new refractory application techniques which would improve the speed of installation. Also methods of hot installation were sought which would allow for hot repairs and on-line maintenance leading to reduced process downtimes and eliminating the need to cool and reheat process vessels.

  17. Solute transport in streams of varying morphology inferred from a high resolution network of potentiometric wireless chloride sensors

    Science.gov (United States)

    Klaus, Julian; Smettem, Keith; Pfister, Laurent; Harris, Nick

    2017-04-01

    There is ongoing interest in understanding and quantifying the travel times and dispersion of solutes moving through stream environments, including the hyporheic zone and/or in-channel dead zones where retention affects biogeochemical cycling processes that are critical to stream ecosystem functioning. Modelling these transport and retention processes requires acquisition of tracer data from injection experiments where the concentrations are recorded downstream. Such experiments are often time consuming and costly, which may be the reason many modelling studies of chemical transport have tended to rely on relatively few well documented field case studies. This leads to the need of fast and cheap distributed sensor arrays that respond instantly and record chemical transport at points of interest on timescales of seconds at various locations in the stream environment. To tackle this challenge we present data from several tracer experiments carried out in the Attert river catchment in Luxembourg employing low-cost (in the order of a euro per sensor) potentiometric chloride sensors in a distributed array. We injected NaCl under various baseflow conditions in streams of different morphologies and observed solute transport at various distances and locations. This data is used to benchmark the sensors to data obtained from more expensive electrical conductivity meters. Furthermore, the data allowed spatial resolution of hydrodynamic mixing processes and identification of chemical 'dead zones' in the study reaches.

  18. Progress of Carbonation in Chloride Contaminated Concretes

    OpenAIRE

    Wang, Yaocheng; Basheer, P. A.M.; Nanukuttan, S; Bai, Y.

    2016-01-01

    Concretes used in marine environment are generally under the cyclic effect of CO2 and chloride ions (Cl-). To date, the influence of carbonation on ingress of chloride ions in concretes has been widely studied; in comparison, study on the influence of Cl- on the progress of carbonation is limited. During the study, concretes were exposed to independent and combined mechanisms of carbonation and chloride ingress regimes. Profiles of apparent pH and chloride concentration were used to indicate ...

  19. Environment

    DEFF Research Database (Denmark)

    Valentini, Chiara

    2017-01-01

    The term environment refers to the internal and external context in which organizations operate. For some scholars, environment is defined as an arrangement of political, economic, social and cultural factors existing in a given context that have an impact on organizational processes and structures....... For others, environment is a generic term describing a large variety of stakeholders and how these interact and act upon organizations. Organizations and their environment are mutually interdependent and organizational communications are highly affected by the environment. This entry examines the origin...... and development of organization-environment interdependence, the nature of the concept of environment and its relevance for communication scholarships and activities....

  20. NOVEL REFRACTORY MATERIALS FOR HIGH ALKALI, HIGH TEMPERATURE ENVIRONMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Hemrick, James Gordon [ORNL; Smith, Jeffrey D [ORNL; O' Hara, Kelley [University of Missouri, Rolla; Rodrigues-Schroer, Angela [Minteq International, Inc.; Colavito, [Minteq International, Inc.

    2012-08-01

    A project was led by Oak Ridge National Laboratory (ORNL) in collaboration with a research team comprised of the academic institution Missouri University of Science and Technology (MS&T), and the industrial company MINTEQ International, Inc. (MINTEQ), along with representatives from the aluminum, chemical, glass, and forest products industries. The project was to address the need for new innovative refractory compositions by developing a family of novel MgO-Al 2O3, MgAl2O4, or other similar spinel structured or alumina-based unshaped refractory compositions (castables, gunnables, shotcretes, etc.) utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques (in-situ phase formation, altered conversion temperatures, accelerated reactions, etc). This family of refractory compositions would then be tailored for use in high-temperature, high-alkaline industrial environments like those found in the aluminum, chemical, forest products, glass, and steel industries. Both practical refractory development experience and computer modeling techniques were used to aid in the design of this new family of materials. The newly developed materials were expected to offer alternative material choices for high-temperature, high-alkali environments that were capable of operating at higher temperatures (goal of increasing operating temperature by 100-200oC depending on process) or for longer periods of time (goal of twice the life span of current materials or next process determined service increment). This would lead to less process down time, greater energy efficiency for associated manufacturing processes (more heat kept in process), and materials that could be installed/repaired in a more efficient manner. The overall project goal was a 5% improvement in energy efficiency (brought about through a 20% improvement in thermal efficiency) resulting in a savings of 3.7 TBtu/yr (7.2 billion ft3 natural gas) by the year 2030. Additionally, new

  1. Diamond based detectors for high temperature, high radiation environments

    Science.gov (United States)

    Metcalfe, A.; Fern, G. R.; Hobson, P. R.; Smith, D. R.; Lefeuvre, G.; Saenger, R.

    2017-01-01

    Single crystal CVD diamond has many desirable properties as a radiation detector; exceptional radiation hardness and physical hardness, chemical inertness, low Z (close to human tissue, good for dosimetry and transmission mode applications), wide bandgap (high temperature operation with low noise and solar blind), an intrinsic pathway to fast neutron detection through the 12C(n,α)9Be reaction. This combination of radiation hardness, temperature tolerance and ability to detect mixed radiation types with a single sensor makes diamond particularly attractive as a detector material for harsh environments such as nuclear power station monitoring (fission and fusion) and oil well logging. Effective exploitation of these properties requires the development of a metallisation scheme to give contacts that remain stable over extended periods at elevated temperatures (up to 250°C in this instance). Due to the cost of the primary detector material, computational modelling is essential to best utilise the available processing methods for optimising sensor response through geometry and conversion media configurations and to fully interpret experimental data. Monte Carlo simulations of our diamond based sensor have been developed, using MCNP6 and FLUKA2011, assessing the sensor performance in terms of spectral response and overall efficiency as a function of the detector and converter geometry. Sensors with varying metallisation schemes for high temperature operation have been fabricated at Brunel University London and by Micron Semiconductor Limited. These sensors have been tested under a varied set of conditions including irradiation with fast neutrons and alpha particles at high temperatures. The presented study indicates that viable metallisation schemes for high temperature contacts have been successfully developed and the modelling results, supported by preliminary experimental data from partners, indicate that the simulations provide a reasonable representation of

  2. Integrated analysis environment for high impact systems

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, M. [Sandia National Labs., Albuquerque, NM (United States); Davis, J.; Scott, J.; Sztipanovits, J.; Karsai, G. [Vanderbilt Univ., Nashville, TN (United States). Measurement and Computing Systems Lab.

    1998-02-01

    Modeling and analysis of high consequence, high assurance systems requires special modeling considerations. System safety and reliability information must be captured in the models. Previously, high consequence systems were modeled using separate, disjoint models for safety, reliability, and security. The MultiGraph Architecture facilitates the implementation of a model integrated system for modeling and analysis of high assurance systems. Model integrated computing allows an integrated modeling technique to be applied to high consequence systems. Among the tools used for analyzing safety and reliability are a behavioral simulator and an automatic fault tree generation and analysis tool. Symbolic model checking techniques are used to efficiently investigate the system models. A method for converting finite state machine models to ordered binary decision diagrams allows the application of symbolic model checking routines to the integrated system models. This integrated approach to modeling and analysis of high consequence systems ensures consistency between the models and the different analysis tools.

  3. Solvothermal synthesis of strontium phosphate chloride nanowire

    Science.gov (United States)

    Lam, W. M.; Wong, C. T.; Li, Z. Y.; Luk, K. D. K.; Chan, W. K.; Yang, C.; Chiu, K. Y.; Xu, B.; Lu, W. W.

    2007-08-01

    Strontium phosphate chloride nanowire was synthesized via a solvothermal treatment of strontium tri-polyphosphate and Collin salt in 1,4-dioxane at 150 °C. The effects of 1,4-dioxane concentration on particle morphology, crystallinity and phase purity were investigated in this study. The specimen morphology was analyzed by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). When the concentration of 1,4-dioxane was below 10%, micron-sized whisker was the dominant form. At 20-25% concentration of 1,4-dioxane, strontium phosphate chloride single-crystalline nanowire was 31±12 nm in diameter and 1.43±0.6 μm in length with an aspect ratio of 52.28±29.41. X-ray diffraction (XRD) pattern of this nanowire matched with that of strontium phosphate chloride (JCPDS #083-0973). When 1,4-dioxane concentration exceeded 25%, nanorod aggregate was the dominant form instead of nanowire. At 20-25% 1,4-dioxane concentration suitable strontium concentration combine with high chemical potential environment favors the formation of nanowires. By adding 1,4-dioxane impure phase such as β-strontium hydrogen phosphate, nanorod formation was suppressed. This method provides an efficient way to synthesize high aspect ratio strontium phosphate chloride nanowire. It has potential bioactive nanocomposite, high mechanical performance bioactive bone cement filler and fluorescent material applications.

  4. High-tech solutions for the environment

    CERN Multimedia

    Gabrielle Thomas

    2013-01-01

    Four solar-powered compactor dustbins have recently been installed at various locations around the Meyrin site. These compact systems fitted with photovoltaic panels compress waste; their increased capacity compared to a standard dustbin reduces the number of collections and the associated CO2 emissions.   Four strange "machines" have recently appeared on the CERN site. Made by the company Big Belly, these intelligent solar-powered mini-compactors fitted with the latest energy-saving technology are perfectly aligned with the Laboratory's policy of minimising the impact of its activities on the environment. With their ability to hold up to four times more waste than the average bin, they need to be emptied less frequently, significantly reducing the CO2 emissions associated with collection and transport. What's more, the integrated software monitors the fill level of each bin in real time and sends an e-mail or text when it needs emptying, thus optimising coll...

  5. STUDY OF CHEMICAL INTERACTION OF MAGNESIA CEMENT WITH HIGH CONCENTRATION MAGNESIUM CHLORIDE SOLUTIONS

    Directory of Open Access Journals (Sweden)

    DEREVIANKO V. N.

    2015-10-01

    Full Text Available Problem statement. In activating MgO by electrolyte salts, as a result of formation of non water-resist magnesium silicate hydrate are obtained the durable cement stone having the low water-resist. I. P. Vyrodov considers [9; 5], that magnesia cement curing in mixing with sufficiently concentrated (C > 20 % solutions MgCl2 is caused with the crystallization of oxyhydrochloride composition: 3MgO∙MgCl2∙11Н2О, 5MgO∙MgCl2∙13Н2О and 7MgO∙MgCl2∙15Н2О. In the lower concentration parts of MgCl2 solution is formed a transitional compound of Mg[(OHnCl2-n] with isomorphous Mg(OH2 structure. At very low Cl concentration only Mg(OH2 is practically formed. Purpose. The Formation of water-resist magnesium silicate hydrates for obtaining of fast curing and solid structure of the magnesia stone. Conclusion. The dependence of the formation of the magnesia stone from the ratio (MgO/MgCl2 of the magnesia cement (MgO and the magnesium chloride solution (MgCl2 of different density has been identified in order to obtain the best content for oxyhydrochloride 3MgO•MgCl2•11Н2О, 5MgO•MgCl2•13Н2О and magnesium hydroxide (Mg(OH2. In putting into the system MgO∙–∙H2О of the silicic acid or fine ground quartz grains with size of less than 20 – 30 microns, over 1 month for the magnesium silicate hydrates formation is needed, where from 2 to 5 % of the total number of newgrowths are created. The study is proved by the expert opinion, that magnesium silicate hydrates do not have binding properties, unlike calcium silicate hydrates, and the main role in the system curing is played with the Mg(OH2 gel recrystallization, which provides the acceptable stone strength (R ≈ 30MPa in a few years. It has been also established, that in mixing of cement with low concentration MgO solutions of less than 1,5 mol/l (or 13% 1,1g/sm3, the final product in the stone structure is Mg(OH2. With increasing the sealer (MgCl2 solution there is formed by turn in

  6. NOVEL REFRACTORY MATERIALS FOR HIGH ALKALI, HIGH TEMPERATURE ENVIRONMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Hemrick, James Gordon [ORNL; Smith, Jeffrey D [ORNL; O' Hara, Kelley [University of Missouri, Rolla; Rodrigues-Schroer, Angela [Minteq International, Inc.; Colavito, [Minteq International, Inc.

    2012-08-01

    A project was led by Oak Ridge National Laboratory (ORNL) in collaboration with a research team comprised of the academic institution Missouri University of Science and Technology (MS&T), and the industrial company MINTEQ International, Inc. (MINTEQ), along with representatives from the aluminum, chemical, glass, and forest products industries. The project was to address the need for new innovative refractory compositions by developing a family of novel MgO-Al 2O3, MgAl2O4, or other similar spinel structured or alumina-based unshaped refractory compositions (castables, gunnables, shotcretes, etc.) utilizing new aggregate materials, bond systems, protective coatings, and phase formation techniques (in-situ phase formation, altered conversion temperatures, accelerated reactions, etc). This family of refractory compositions would then be tailored for use in high-temperature, high-alkaline industrial environments like those found in the aluminum, chemical, forest products, glass, and steel industries. Both practical refractory development experience and computer modeling techniques were used to aid in the design of this new family of materials. The newly developed materials were expected to offer alternative material choices for high-temperature, high-alkali environments that were capable of operating at higher temperatures (goal of increasing operating temperature by 100-200oC depending on process) or for longer periods of time (goal of twice the life span of current materials or next process determined service increment). This would lead to less process down time, greater energy efficiency for associated manufacturing processes (more heat kept in process), and materials that could be installed/repaired in a more efficient manner. The overall project goal was a 5% improvement in energy efficiency (brought about through a 20% improvement in thermal efficiency) resulting in a savings of 3.7 TBtu/yr (7.2 billion ft3 natural gas) by the year 2030. Additionally, new

  7. 高效聚结器在氯乙烯生产中的应用%Application of high effective coalescer in production of vinyl chloride

    Institute of Scientific and Technical Information of China (English)

    毛丽萍; 范声朴; 张恒云

    2012-01-01

    介绍了氯乙烯深度脱水工艺及聚结器脱水原理,将高效聚结器应用于氯乙烯精馏工序中,实现了氯乙烯的深度脱水,满足了聚合工序的工艺要求,提高了产品的质量。%Deep dewatering process for vinyl chloride and the dewatering mechanism of coalescer were introduced.The application of high effective coalescer in vinyl chloride distillation procedure realized the deep dewatering of vinyl chloride,thus meeting the process requirement of polymerization procedure,and improving the product quality.

  8. Chemical tracers of high-metallicity environments

    CERN Document Server

    Bayet, E; Bell, T A; Viti, S

    2012-01-01

    We present for the first time a detailed study of the properties of molecular gas in metal-rich environments such as early-type galaxies (ETGs). We have explored Photon-Dominated Region (PDR) chemistry for a wide range of physical conditions likely to be appropriate for these sources. We derive fractional abundances of the 20 most chemically reactive species as a function of the metallicity, as a function of the optical depth and for various volume number gas densities, Far-Ultra Violet (FUV) radiation fields and cosmic ray ionisation rates. We also investigate the response of the chemistry to the changes in $\\alpha-$element enhancement as seen in ETGs. We find that the fractional abundances of CS, H$_{2}$S, H$_{2}$CS, H$_{2}$O, H$_{3}$O$^{+}$, HCO$^{+}$ and H$_{2}$CN seem invariant to an increase of metallicity whereas C$^{+}$, CO, C$_{2}$H, CN, HCN, HNC and OCS appear to be the species most sensitive to this change. The most sensitive species to the change in the fractional abundance of $\\alpha-$elements ar...

  9. High efficiency removal of 2-chlorophenol from drinking water by a hydrogen-based polyvinyl chloride membrane biofilm reactor.

    Science.gov (United States)

    Xia, Siqing; Zhang, Zhiqiang; Zhong, Fohua; Zhang, Jiao

    2011-02-28

    A continuously stirred hydrogen-based membrane biofilm reactor (MBfR) with polyvinyl chloride (PVC) hollow fiber membrane was investigated for removing 2-chlorophenol (2-CP) from contaminated drinking water. The bioreactor startup was achieved by acclimating the microorganisms from a denitrifying and sulfate-reducing MBfR to the drinking water contaminated by 2-CP. The effects of some major factors, including 2-CP loading, H(2) pressure, nitrate loading, and sulfate loading, on the removal of 2-CP by the MBfR were systematically investigated. Although the effluent 2-CP concentration increased with its increasing influent loading, the removing efficiency of 2-CP by the MBfR could be up to 94.7% under a high influent loading (25.71 mg/L d). The removing efficiency of 2-CP by the MBfR could be improved by higher H(2) pressure, and lower influent nitrate concentration and sulfate concentration. A high H(2) pressure can assure enough available H(2) as the electron donor for 2-CP degradation. The competition in the electron donor made nitrate and sulfate inhibit the degradation of 2-CP in the MBfR. The electron flux analyses indicated that the degradation of 2-CP only accounted for a small part of electron flux, and the autohydrogenotrophic bacteria in the MBfR were highly efficient for the 2-CP removal.

  10. Hearing Protection for High-Noise Environments

    Science.gov (United States)

    2009-12-31

    based on a modified form of the volumetric Lippmann- Schwinger integral equation, adapted to the treatment of high-contrast problems. It utilizes a...the reformulation of the conventional Lippmann- Schwinger (L-S) equations which we developed in the case of acoustics (Reference 2 in Section 6). By

  11. The tetramethylammonium chloride method for screening of cDNA libraries using highly degenerate oligonucleotides obtained by backtranslation of amino-acid sequences

    DEFF Research Database (Denmark)

    Honoré, B; Madsen, Peder; Leffers, H

    1993-01-01

    We describe a method for screening of cDNA libraries with highly degenerate oligonucleotides using tetramethylammonium chloride (TMAC). This method is a convenient alternative to using probes generated by the polymerase chain reaction (PCR), especially when these cannot easily be made. Nylon filt...

  12. Review of COD testing methods for high concentration chloride waste water%高浓度氯离子废水COD测试方法综述

    Institute of Scientific and Technical Information of China (English)

    孙明坤

    2015-01-01

    This paper reviews the principles and case studies of avoiding Cl-interference on COD testing for waste water with high concentration chloride ions.%本文主要论述高浓度氯离子水COD测定里多种防止Cl-影响的方法原理及实际案例。

  13. Calcium chloride doped zinc-cobalt metal-cyanide complex: Unexpected highly activity towards ring-opening polymerization of propylene oxide

    Institute of Scientific and Technical Information of China (English)

    Yi Jun Huang; Xing Hong Zhang; Zheng Jiang Hua; Guo Rong Qi

    2010-01-01

    Highly active calcium chloride (CaCl2) doped Zn-CoⅢ double metal-cyanide (Ca-DMC) catalysts were firstly reported. Ca-DMCs presented a very higher polymer yield (54 kg polymer/g catalyst) at relative low temperature (80-115 ℃) toward ring-opening polymerization (ROP) of propylene oxide (PO) than did DMC catalysts without modification.

  14. Chloride transference during electrochemical chloride extraction process

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    Chemical titration method and lab-made chloride probes were jointly adopted to investigate the effects of water-to-cement (W/C) ratio and the impressed current density on chloride transport for cement-based materials during electrochemical chloride extraction (ECE) process.The dissolution of bound chlorides and the effect of current density on dissolution were analyzed.The variations of chloride concentration at different depths and the chloride transference process were monitored.Test results show that W/C ratios adopted have slight influence on chloride extraction,while chloride extraction efficiency is mainly determined by the impressed current density.During ECE process a portion of bound chloride ions dissolved and the amount of bound chlorides released is directly proportional to current density.

  15. Antifungal activity of benzalkonium chloride, dettol , and chlorhexidine on opportunistic isolated fungi from the environment and operating rooms in private clinics of Tehran in 2011

    Directory of Open Access Journals (Sweden)

    Hossein Nowrozi

    2013-11-01

    Conclusion: Benzalkonium chloride and Dettol had a complete antifungal activity, but chlorhexidine was found to be the least effective agent.. Therefore, the tested concentrations give out their most fungicidal activity as disinfectants, if their durability is taken into account.

  16. Track reconstruction in CMS high luminosity environment

    CERN Document Server

    Sguazzoni, Giacomo

    2014-01-01

    The CMS tracker is the largest silicon detector ever built, covering 200 square meters and providing an average of 14 high-precision measurements per track. Tracking is essential for the reconstruction of objects like jets, muons, electrons and tau leptons starting from the raw data from the silicon pixel and strip detectors. Track reconstruction is widely used also at trigger level as it improves objects tagging and resolution.The CMS tracking code is organized in several levels, known as iterative steps, each optimized to reconstruct a class of particle trajectories, as the ones of particles originating from the primary vertex or displaced tracks from particles resulting from secondary vertices. Each iterative step consists of seeding, pattern recognition and fitting by a kalman filter, and a final filtering and cleaning. Each subsequent step works on hits not yet associated to a reconstructed particle trajectory.The CMS tracking code is continuously evolving to make the reconstruction computing load compat...

  17. Continuous high PRF waveforms for challenging environments

    Science.gov (United States)

    Jaroszewski, Steven; Corbeil, Allan; Ryland, Robert; Sobota, David

    2017-05-01

    Current airborne radar systems segment the available time-on-target during each beam dwell into multiple Coherent Processing Intervals (CPIs) in order to eliminate range eclipsing, solve for unambiguous range, and increase the detection performance against larger Radar Cross Section (RCS) targets. As a consequence, these radars do not realize the full Signal-to-Noise Ratio (SNR) increase and detection performance improvement that is possible. Continuous High Pulse Repetition Frequency (HPRF) waveforms and processing enables the coherent integration of all available radar data over the full time-on-target. This can greatly increase the SNR for air targets at long range and/or with weak radar returns and significantly improve the detection performance against such targets. TSC worked with its partner KeyW to implement a Continuous HPRF waveform in their Sahara radar testbed and obtained measured radar data on both a ground vehicle target and an airborne target of opportunity. This experimental data was processed by TSC to validate the expected benefits of Continuous HPRF waveforms.

  18. HIGH-BANDWITH MULTICAST IN COOPERATIVE ENVIRONMENTS

    Directory of Open Access Journals (Sweden)

    A.Darwin Marks

    2015-10-01

    Full Text Available We study the matter of maximizing the printed rate in peer-to-peer (P2P systems underneath node degree bounds, i.e., the quantity of neighbors a node will at the same time hook up with is upper-bounded. The matter is important for supporting high-quality video streaming in P2P systems and is difficult because of its combinatorial nature. during this paper, we tend to address this drawback by providing the primary distributed answer that achieves near-optimal broadcast rate underneath capricious node degree bounds and over capricious overlay graph. It runs on individual nodes and utilizes solely the measuring from their one-hop neighbors, creating the answer simple to implement and all-mains to see churn and network dynamics. Our answer consists of 2 distributed algorithmic programs planned during this paper which will be of freelance interests: a network-coding-based broadcasting algorithm that optimizes the printed rate given a topology, and a Markov-chain target-hunting topology hopping algorithmic program that optimizes the topology. Our distributed broadcasting algorithmic program achieves the optimum broadcast rate over capricious P2P topology, whereas antecedently planned distributed algorithms get optimality just for P2P complete graphs. We tend to prove the optimality of our answer and its convergence to a district round the optimal equilibrium underneath strident measurements or while not time-scale separation assumptions. we tend to demonstrate the effectiveness of our answer in simulations victimization transmission information measure statistics of web hosts.

  19. Graphene supported silver@silver chloride & ferroferric oxide hybrid, a magnetically separable photocatalyst with high performance under visible light irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Zhong, Suting; Jiang, Wei, E-mail: superfine_jw@126.com; Han, Mei; Liu, Gongzong; Zhang, Na; Lu, Yue

    2015-08-30

    Graphical abstract: - Highlights: • The composites were synthesized via a facile and effective process. • Plenty of Fe{sub 3}O{sub 4} and Ag@AgCl nanoparticles are deposited on the reduced graphene oxide nanosheets. • The catalyst exhibited an enhanced photocatalytic performance and magnetic property. • The catalyst is stable under the visible light irradiation. - Abstract: A stable magnetic separable plasmonic photocatalyst was successfully fabricated by grafting silver@silver chloride (Ag@AgCl) and ferroferric oxide (Fe{sub 3}O{sub 4}) nanoparticles on graphene sheets. The composite exhibited high activity degrading methylene blue (MB) and rhodamine B (RB) under visible light irradiation: decomposition 97.4% of MB in 100 min and 97.9% of RB in 120 min. The enhanced photocatalytic activities can be attributed to synergistic effect between Ag@AgCl and graphene: the effective charge transfer from Ag@AgCl to graphene thus promotes the separation of electron–hole pairs. Moreover, the excellent magnetic property gives a more convenient way to recycle the photocatalysts.

  20. EFFECT OF RADIATION ON HIGH-CHARGE-DENSITY POLYDIALLY-DIMETHYL AMMONIUM CHLORIDE IN DILUTE AQUEOUS SOLUTION

    Institute of Scientific and Technical Information of China (English)

    Ya-long Zhang; Min Yi; Jing Ren; Hong-fei Ha

    2003-01-01

    The effect of radiation on high-charge-density cationic polymer, polydiallyl-dimethyl ammonium chloride (polyDADMAC), in dilute aqueous solution was investigated. The irradiated samples were characterized in terms of reduced viscosity and electric conductivity. The crosslinking reaction of polyDADMAC chains occurs preferentially in the irradiated samples at a concentration of polyDADMAC higher than 1.3 g/100 mL that was induced indirectly by the OH radicals, one of the radiolysis products of water. In more dilute samples (less than 0.8 g/100 mL) the chain scission of macro radicals appears to be the main reaction. N2O atmosphere enhances the erosslinking due to the extra OH radicals produced by reaction between N2O and eaq, another radiolysis products of water. Methanol and some mineral salts such as KC1, KBr inhibit the crosslinking to a certain extent. The mechanism of sensitization and inhibition is discussed in detail.

  1. Corrosion Resistance and Pitting Behaviour of Low-Carbon High-Mn Steels in Chloride Solution

    Directory of Open Access Journals (Sweden)

    Grajcar A.

    2016-06-01

    Full Text Available Corrosion resistance of the X4MnSiAlNbTi27-4-2 and X6MnSiAlNbTi26-3-3 type austenitic steels, after hot deformation as well as after cold rolling, were evaluated in 3.5% NaCl solution using potentiodynamic polarization tests. A type of nonmetallic inclusions and their pitting corrosion behaviour were investigated. Additionally, the effect of cold deformation on the corrosion resistance of high-Mn steels was studied. The SEM micrographs revealed that corrosion damage formed in both investigated steels is characterized by various shapes and an irregular distribution at the metallic matrix, independently on the steel state (thermomechanically treated or cold worked. Corrosion pits are generated both in grain interiors, grain boundaries and along the deformation bands. Moreover, corrosion damage is stronger in cold deformed steels in comparison to the thermomechanically treated specimens. EDS analysis revealed that corrosion pits preferentially nucleated on MnS and AlN inclusions or complex oxysulphides. The morphology of corrosion damage in 3.5% NaCl supports the data registered in potentiodynamic tests.

  2. Politics in evaluation: Politically responsive evaluation in high stakes environments.

    Science.gov (United States)

    Azzam, Tarek; Levine, Bret

    2015-12-01

    The role of politics has often been discussed in evaluation theory and practice. The political influence of the situation can have major effects on the evaluation design, approach and methods. Politics also has the potential to influence the decisions made from the evaluation findings. The current study focuses on the influence of the political context on stakeholder decision making. Utilizing a simulation scenario, this study compares stakeholder decision making in high and low stakes evaluation contexts. Findings suggest that high stakes political environments are more likely than low stakes environments to lead to reduced reliance on technically appropriate measures and increased dependence on measures better reflect the broader political environment.

  3. Synthesis and Properties of High Strength Thin Film Composites of Poly(ethylene Oxide) and PEO-PMMA Blend with Cetylpyridinium Chloride Modified Clay

    OpenAIRE

    Mohammad Saleem Khan; Sabiha Sultana

    2015-01-01

    Ion-conducting thin film composites of polymer electrolytes were prepared by mixing high MW poly(ethylene oxide) (PEO), poly(methyl methacrylate) (PMMA) as a polymer matrix, cetylpyridinium chloride (CPC) modified MMT as filler, and different content of LiClO4 by using solution cast method. The crystallinity, ionic conductivity (σ), and mechanical properties of the composite electrolytes and blend composites were evaluated by using XRD, AC impedance, and UTM studies, respectively. The modific...

  4. Zirconyl Chloride Promoted Highly Efficient Domino Synthesis of New 1, 2, 3, 4-Tetrahydroquinoline Derivatives in Water

    Institute of Scientific and Technical Information of China (English)

    Rahul R. NAGAWADE; Devanand B. SHINDE

    2006-01-01

    The tetrahydroquinoline moiety is a structural feature of many natural products. By using a domino reaction of aromatic amines and cyclic enol ethers catalyzed by zirconyl chloride in water, various tetrahydroquinoline derivatives were synthesized efficiently. Most cyclized products showed cis selectivity. The cis selectivity was tentatively rationalized due to chelation control in water.

  5. Microbial communities associated with the anthropogenic, highly alkaline environment of a saline soda lime, Poland.

    Science.gov (United States)

    Kalwasińska, Agnieszka; Felföldi, Tamás; Szabó, Attila; Deja-Sikora, Edyta; Kosobucki, Przemysław; Walczak, Maciej

    2017-07-01

    Soda lime is a by-product of the Solvay soda process for the production of sodium carbonate from limestone and sodium chloride. Due to a high salt concentration and alkaline pH, the lime is considered as a potential habitat of haloalkaliphilic and haloalkalitolerant microbial communities. This artificial and unique environment is nutrient-poor and devoid of vegetation, due in part to semi-arid, saline and alkaline conditions. Samples taken from the surface layer of the lime and from the depth of 2 m (both having pH ~11 and ECe up to 423 dS m(-1)) were investigated using culture-based (culturing on alkaline medium) and culture-independent microbiological approaches (microscopic analyses and pyrosequencing). A surprisingly diverse bacterial community was discovered in this highly saline, alkaline and nutrient-poor environment, with the bacterial phyla Proteobacteria (representing 52.8% of the total bacterial community) and Firmicutes (16.6%) showing dominance. Compared to the surface layer, higher bacterial abundance and diversity values were detected in the deep zone, where more stable environmental conditions may occur. The surface layer was dominated by members of the genera Phenylobacterium, Chelativorans and Skermanella, while in the interior layer the genus Fictibacillus was dominant. The culturable aerobic, haloalkaliphilic bacteria strains isolated in this study belonged mostly to the genus Bacillus and were closely related to the species Bacillus pseudofirmus, B. cereus, B. plakortidis, B. thuringensis and B. pumilus.

  6. Adsorption of alkyl-dimethyl-benzyl-ammonium chloride on low-weight greige and bleached cotton nonwovens in different aqueous environments

    Science.gov (United States)

    Previous research has shown the adsorption of alkyl-dimethyl-benzyl-ammonium chloride (ADBAC) on cotton nonwovens is dependent on pretreatment of the substrate, more specifically whether it is greige or bleached fabric. In this work we examine the effect of varying the chemical and physical propert...

  7. Teamwork in high-risk environments analogous to space

    Science.gov (United States)

    Kanki, Barbara G.

    1990-01-01

    Mountaineering expeditions combine a number of factors which make them potentially good analogs to the planetary exploration facet of long-duration space missions. A study of mountain climbing teams was conducted in order to evaluate the usefulness of the environment as a space analog and to specifically identify the factors and issues surrounding teamwork and 'successful' team performance in two mountaineering environments. This paper focuses on social/organizational factors, including team size and structure, leadership styles and authority structure which were found in the sample of 22 climb teams (122 individuals). The second major issue discussed is the construction of a valid performance measure in this high-risk environment.

  8. High temperature erosion testing in a gasifier environment

    Energy Technology Data Exchange (ETDEWEB)

    Tylczak, Joseph H.; Rawers, James C.; Adler, Thomas A.

    2004-01-01

    The development of materials with the ability to operate in adverse conditions while resisting the effects of erosion and corrosion is essential to the future success of high efficiency power plants. Many next generation coal power plants are envisioned as combined cycle, with gasifiers used to produce both steam and syngas. The gasifier sections of these plants require materials of construction that are resistant to the effects of erosion from silica found in the gas streams and corrosion caused by a reducing atmosphere that may contain sulfur and chloride compounds. The Albany Research Center has developed a test apparatus designed to test the erosion-resistance of candidate materials under a range of environmental conditions, including those found in gasifiers. This Hostile Atmosphere Erosion Wear test apparatus (HAET) has been used to evaluate a group of high alloy candidate materials such as iron aluminide and Haynes HR 160, and compare them to a conventional 310 stainless steel. Erosion tests were conducted using 270μm silica abrasive, a typical impact velocities of 20 m/sec at temperatures up to 700°C in an atmosphere simulating gasifier conditions. The effects of erosion under these conditions on the surface scales that form are described. The total loss rate, loss rates due to erosion and corrosion for the test materials are compared.

  9. Anion Receptor Design: Exploiting Outer-Sphere Coordination Chemistry To Obtain High Selectivity for Chloridometalates over Chloride.

    Science.gov (United States)

    Carson, Innis; MacRuary, Kirstian J; Doidge, Euan D; Ellis, Ross J; Grant, Richard A; Gordon, Ross J; Love, Jason B; Morrison, Carole A; Nichol, Gary S; Tasker, Peter A; Wilson, A Matthew

    2015-09-01

    High anion selectivity for PtCl6(2-) over Cl(-) is shown by a series of amidoamines, R(1)R(2)NCOCH2CH2NR(3)R(4) (L1 with R(1) = R(4) = benzyl and R(2) = R(3) = phenyl and L3 with R(1) = H, R(2) = 2-ethylhexyl, R(3) = phenyl and R(4) = methyl), and amidoethers, R(1)R(2)NCOCH2CH2OR(3) (L5 with R(1) = H, R(2) = 2-ethylhexyl and R(3) = phenyl), which provide receptor sites which extract PtCl6(2-) preferentially over Cl(-) in extractions from 6 M HCl solutions. The amidoether receptor L5 was found to be a much weaker extractant for PtCl6(2-) than its amidoamine analogues. Density functional theory calculations indicate that this is due to the difficulty in protonating the amidoether to generate a cationic receptor, LH(+), rather than the latter showing weaker binding to PtCl6(2-). The most stable forms of the receptors, LH(+), contain a tautomer in which the added proton forms an intramolecular hydrogen bond to the amide oxygen atom to give a six-membered proton chelate. Dispersion-corrected DFT calculations appear to suggest a switch in ligand conformation for the amidoamine ligands to an open tautomer state in the complex, such that the cationic N-H or O-H groups are also readily available to form hydrogen bonds to the PtCl6(2-) ion, in addition to the array of polarized C-H bonds. The predicted difference in energies between the proton chelate and nonchelated tautomer states for L1 is small, however, and the former is found in the X-ray crystal structure of the assembly [(L1H)2PtCl6]. The DFT calculations and the X-ray structure indicate that all LH(+) receptors present an array of polarized C-H groups to the large, charge diffuse PtCl6(2-) anion resulting in high selectivity of extraction of PtCl6(2-) over the large excess of chloride.

  10. Effects of high dietary sodium chloride content on performance and sodium and potassium balance in growing pigs.

    Science.gov (United States)

    Chittavong, Malavanh; Jansson, Anna; Lindberg, Jan Erik

    2013-10-01

    Thirty castrated male Moo Lath pigs (6-8 weeks of age) were used in a 15-week growth trial to study the effect of high dietary sodium chloride (NaCl) content on feed and water intake, performance, sodium (Na) and potassium (K) balance, and plasma aldosterone concentration. The pigs were randomly allocated (ten per treatment) to diets containing 0.24 % Na (Na0.24), 0.28 % Na (Na0.28), and 0.32 % Na (Na0.32) per kg diet. Feed and water was provided ad libitum, and water consumption, feed offered, and feed residues were recorded daily. Every third week, the pigs were weighed, blood samples were collected, and a 3-day total collection of urine and feces was performed. Water intake was higher (P = 0.001) in pigs fed with diets Na0.28 (3.7 L/day) and Na0.32 (3.9 L/day) than in pigs fed with diet Na0.24 (3.4 L/day), and dry matter (DM) intake was higher on diet Na0.32 (P = 0.041) than on the other diets. The average daily body weight (BW) gain was higher on diet Na0.32 than on the other diets (P = 0.031). The feed conversion ratio (in kilogram feed DM to kilogram BW gain) was 4.6, 4.6, and 4.1 on treatments Na0.24, Na0.28, and Na0.32, respectively (P = 0.14). The highest Na balance was observed on diet Na0.32 followed by diets Na0.28 and Na0.24 (P < 0.001), while there was no treatment-related pattern for the K balance. The Na/K ratio in feces and urine increased (P < 0.001), and the K/Na ratio in feces (P < 0.001) decreased with increasing Na content in the diet. Plasma aldosterone concentration decreased (P < 0.001) with increasing dietary content of Na. These results indicate that high NaCl intake and free access to water will increase Na balance but do not negatively influence feed intake and performance of growing local pigs.

  11. Studies on wind environment around high buildings in urban areas

    Institute of Scientific and Technical Information of China (English)

    LIU; Huizhi; JIANG; Yujun; LIANG; Bin; ZHU; Fengrong; ZHAN

    2005-01-01

    High buildings or architectural complex in urban areas remarkably distort the urban surface wind fields. As the air flow approaches,local strong wind may appear around the buildings. The strong wind makes the pedestrians on sidewalks, entrances and terrace very uncomfortable and causes the pedestrian level wind environment problem. In this studies, hot-wire wind measurement, wind scouring in wind tunnel and numerical computation were carried out to evaluate the wind environment of tall buildings in the prevailing flow conditions in Beijing areas. The results obtained by three techniques were compared and mutually verified. The conclusions drawn from three approaches agree with each other. Also the advantages and limitations of each method were analyzed. It is suggested that the combination of different techniques may produce better assessment of wind environment around high buildings.

  12. Recurrent studies of chloride ingress in uncracked marine concrete at various exposure times and elevations

    Energy Technology Data Exchange (ETDEWEB)

    Sandburg, P. [Lund Inst. of Tech. (Sweden). Div. of Building Materials; Tang, L. [Swedish National Testing and Research Inst., Boraes (Sweden); Andersen, A. [Chalmers Univ., Goeteborg (Sweden). Div. of Building Materials

    1998-10-01

    Uncracked reinforced concrete slabs were field exposed mounted on a floating pontoon and partly submerged for 5 years at the Swedish west coast. The total chloride ingress was analyzed at various exposure times at 3 elevations representing a submerged, a splash, and an atmospheric exposure zone. The concrete mixtures varied in w/c ratio, type of cement, and amount and type of pozzolan used in the binder. The data is unique as it represents recurrently measured total chloride penetration profiles at various exposure ages, providing a foundation for the prediction of chloride ingress in concrete in a given environment. The results after 5 years of exposure confirmed the expected inverse relationship between water-to-binder ratio and chloride ingress. The use of 5--10% silica fume in the binder had a very positive effect on reducing the chloride ingress, but little or no benefit at all was found for concrete with fly ash in the binder as compared to the use of 5% silica fume. The chloride penetration rate as expressed by a calculated effective chloride diffusivity has a tendency to decrease over time. High-performance concrete with w/c {le} 0.4 and a minimum of 5% silica fume added as a well dispersed slurry exhibited an effective chloride diffusivity in the range of 1 {times} 10{sup {minus}13} to 5 {times} 10{sup {minus}13} m{sup 2}/s after 5 years exposure in the splash zone.

  13. Removal of As(V), Cr(III) and Cr(VI) from aqueous environments by poly(acrylonitril-co-acrylamidopropyl-trimethyl ammonium chloride)-based hydrogels.

    Science.gov (United States)

    Dudu, Tuba Ersen; Sahiner, Mehtap; Alpaslan, Duygu; Demirci, Sahin; Aktas, Nahit

    2015-09-15

    Cationic poly(Acrylonitril-co-Acrylamidopropyl-trimethyl Ammonium Chloride) (p(AN-co-APTMACl)) hydrogels in bulk were synthesized by using acrylonitrile (AN) and 3-acrylamidopropyl-trimethyl ammonium chloride (APTMACl) as monomers. The prepared hydrogels were exposed to amidoximation reaction to replace hydrophobic nitrile groups with hydrophilic amidoxime groups that have metal ion binding ability. Those replacements were increased the hydrogels absorption capacity for As(V) and Cr(VI). Langmuir and Freundlich isotherms equations were utilized to obtain the best-fitted isotherm model for the absorption of the ions at different metal ion concentrations. The absorption data of As(V) ion were fitted well to Freundlich isotherm while those of Cr(VI) and Cr(III) ions were fitted well to Langmuir isotherm. The maximum absorption of poly(3-acrylamidopropyl-trimethyl ammonium chloride (p(APTMACl)) and amid-p(AN-co-APTMACl) macro gels were 22.39 mg and 21.83 mg for As(V), and 30.65 mg and 18.16 mg for Cr(VI) ion per unit gram dried gel, respectively. Kinetically, the absorption behaviors of Cr(III) and Cr(VI) ions were fitted well to a pseudo 2nd-order kinetic model and those of As(V) ions were fitted well to a pseudo 1st order kinetic model.

  14. Advocacy for Child Wellness in High-Poverty Environments

    Science.gov (United States)

    Mullen, Carol A.

    2014-01-01

    Child wellness needs to be understood holistically so that children and youth from high-poverty environments can succeed in schooling and life. Teachers who foster advocacy in themselves are well equipped to teach students to take ownership of their own well-being. Such advocacy can enrich the classroom curriculum and mitigate the negative effects…

  15. Profiles Junior high School West Java in Education Learning Environment

    Directory of Open Access Journals (Sweden)

    NFN Nahadi

    2014-02-01

    Full Text Available Descriptive studies have been conducted on the existing junior high profile in West Java on Education Learning Environment. The study was conducted by purposive sampling and descriptive done to get an idea about the profile of SMP in West Java implementation of the learning environment. in junior high school in West Java. Research conducted by distributing questionnaires, and observations based on the indicators developed. Based on this research, it is known that, PLH learning in junior high school in West Java has been in force since 2007 after the enactment of the Governor of West Java on environmental education for junior high school students in West Java. Learning that lasts generally implemented in conventional teacher, and it is without any innovations. It has made learning the essential condition runs well, but has not lasted optimally.

  16. Effects of high combustion chamber pressure on rocket noise environment

    Science.gov (United States)

    Pao, S. P.

    1972-01-01

    The acoustical environment for a high combustion chamber pressure engine was examined in detail, using both conventional and advanced theoretical analysis. The influence of elevated chamber pressure on the rocket noise environment was established, based on increase in exit velocity and flame temperature, and changes in basic engine dimensions. Compared to large rocket engines, the overall sound power level is found to be 1.5 dB higher, if the thrust is the same. The peak Strouhal number shifted about one octave lower to a value near 0.01. Data on apparent sound source location and directivity patterns are also presented.

  17. Galaxy Merger Candidates in High-redshift Cluster Environments

    Science.gov (United States)

    Delahaye, A. G.; Webb, T. M. A.; Nantais, J.; DeGroot, A.; Wilson, G.; Muzzin, A.; Yee, H. K. C.; Foltz, R.; Noble, A. G.; Demarco, R.; Tudorica, A.; Cooper, M. C.; Lidman, C.; Perlmutter, S.; Hayden, B.; Boone, K.; Surace, J.

    2017-07-01

    We compile a sample of spectroscopically and photometrically selected cluster galaxies from four high-redshift galaxy clusters (1.59contamination from interlopers, {11.0}-5.6+7.0 % of the cluster members are involved in potential mergers, compared to {24.7}-4.6+5.3 % of the field galaxies. We see no evidence of merger enhancement in the central cluster environment with respect to the field, suggesting that galaxy-galaxy merging is not a stronger source of galaxy evolution in cluster environments compared to the field at these redshifts.

  18. Context-aware Authorization in Highly Dynamic Environments

    CERN Document Server

    Tigli, Jean-Yves; Rey, Gaetan; Hourdin, Vincent; Riveill, Michel

    2011-01-01

    Highly dynamic computing environments, like ubiquitous and pervasive computing environments, require frequent adaptation of applications. Context is a key to adapt suiting user needs. On the other hand, standard access control trusts users once they have authenticated, despite the fact that they may reach unauthorized contexts. We analyse how taking into account dynamic information like context in the authorization subsystem can improve security, and how this new access control applies to interaction patterns, like messaging or eventing. We experiment and validate our approach using context as an authorization factor for eventing in Web service for device (like UPnP or DPWS), in smart home security.

  19. Context-aware Authorization in Highly Dynamic Environments

    Directory of Open Access Journals (Sweden)

    Vincent Hourdin

    2009-09-01

    Full Text Available Highly dynamic computing environments, like ubiquitous and pervasive computing environments, require frequent adaptation of applications. Context is a key to adapt suiting user needs. On the other hand, standard access control trusts users once they have authenticated, despite the fact that they may reach unauthorized contexts. We analyse how taking into account dynamic information like context in the authorization subsystem can improve security, and how this new access control applies to interaction patterns, like messaging or eventing. We experiment and validate our approach using context as an authorization factor for eventing in Web service for device (like UPnP or DPWS, in smart home security.

  20. The development of advanced robotics technology in high radiation environment

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Yong Bum; Cho, Jaiwan; Lee, Nam Ho; Choi, Young Soo; Park, Soon Yong; Lee, Jong Min; Park, Jin Suk; Kim, Seung Ho; Kim, Byung Soo; Moon, Byung Soo

    1997-07-01

    In the tele-operation technology using tele-presence in high radiation environment, stereo vision target tracking by centroid method, vergence control of stereo camera by moving vector method, stereo observing system by correlation method, horizontal moving axis stereo camera, and 3 dimensional information acquisition by stereo image is developed. Also, gesture image acquisition by computer vision and construction of virtual environment for remote work in nuclear power plant. In the development of intelligent control and monitoring technology for tele-robot in hazardous environment, the characteristics and principle of robot operation. And, robot end-effector tracking algorithm by centroid method and neural network method are developed for the observation and survey in hazardous environment. 3-dimensional information acquisition algorithm by structured light is developed. In the development of radiation hardened sensor technology, radiation-hardened camera module is designed and tested. And radiation characteristics of electric components is robot system is evaluated. Also 2-dimensional radiation monitoring system is developed. These advanced critical robot technology and telepresence techniques developed in this project can be applied to nozzle-dam installation /removal robot system, can be used to realize unmanned remotelization of nozzle-dam installation / removal task in steam generator of nuclear power plant, which can be contributed for people involved in extremely hazardous high radioactivity area to eliminate their exposure to radiation, enhance their task safety, and raise their working efficiency. (author). 75 refs., 21 tabs., 15 figs.

  1. High-rise Buildings versus Outdoor Thermal Environment in Chongqing

    Directory of Open Access Journals (Sweden)

    Jin-sha Wang

    2007-10-01

    Full Text Available This paper gives a brief description of the over quick urbanization sinceChongqing, one of the biggest cities in China, has been a municipality directly under theCentral Government in 1997, excessive development and exceeding increase of high-risebuildings because of its special geographical position which finally leads to the worseningof the urban outdoor thermal environment. Then, this paper makes a bright balance to thefield measurement and simulated results of the wind speed field, temperature field of onemultifunctional high-rise building in Chongqing university located in the city center, andthe contrasted results validate the correctness of CFD in the outdoor thermal environmentalsimulation, expose the disadvantages of high-rise buildings on the aspects of blocking thewind field, decreasing wind speed which results in accumulation of the air-conditioningheat revolving around and periscian region where sunshine can not rip into. Finally, inorder to improve the urban outdoor thermal environment near the high-rise buildingsespecially for the angle of natural ventilation, this paper simulates the wind environment indifferent architectural compositions and architectural layouts by CFD, and the simulatedresults show that freestyle and tower buildings which can guarantee the wind speed andtake the air-conditioning heat away are much suitable and reasonable for the specialChongqing geography. These conclusions can also be used as a reference in othermountain cities, especially for the one with a great number of populations.

  2. Spectroscopic gamma camera for use in high dose environments

    Science.gov (United States)

    Ueno, Yuichiro; Takahashi, Isao; Ishitsu, Takafumi; Tadokoro, Takahiro; Okada, Koichi; Nagumo, Yasushi; Fujishima, Yasutake; Kometani, Yutaka; Suzuki, Yasuhiko; Umegaki, Kikuo

    2016-06-01

    We developed a pinhole gamma camera to measure distributions of radioactive material contaminants and to identify radionuclides in extraordinarily high dose regions (1000 mSv/h). The developed gamma camera is characterized by: (1) tolerance for high dose rate environments; (2) high spatial and spectral resolution for identifying unknown contaminating sources; and (3) good usability for being carried on a robot and remotely controlled. These are achieved by using a compact pixelated detector module with CdTe semiconductors, efficient shielding, and a fine resolution pinhole collimator. The gamma camera weighs less than 100 kg, and its field of view is an 8 m square in the case of a distance of 10 m and its image is divided into 256 (16×16) pixels. From the laboratory test, we found the energy resolution at the 662 keV photopeak was 2.3% FWHM, which is enough to identify the radionuclides. We found that the count rate per background dose rate was 220 cps h/mSv and the maximum count rate was 300 kcps, so the maximum dose rate of the environment where the gamma camera can be operated was calculated as 1400 mSv/h. We investigated the reactor building of Unit 1 at the Fukushima Dai-ichi Nuclear Power Plant using the gamma camera and could identify the unknown contaminating source in the dose rate environment that was as high as 659 mSv/h.

  3. Spectroscopic gamma camera for use in high dose environments

    Energy Technology Data Exchange (ETDEWEB)

    Ueno, Yuichiro, E-mail: yuichiro.ueno.bv@hitachi.com [Research and Development Group, Hitachi, Ltd., Hitachi-shi, Ibaraki-ken 319-1221 (Japan); Takahashi, Isao; Ishitsu, Takafumi; Tadokoro, Takahiro; Okada, Koichi; Nagumo, Yasushi [Research and Development Group, Hitachi, Ltd., Hitachi-shi, Ibaraki-ken 319-1221 (Japan); Fujishima, Yasutake; Kometani, Yutaka [Hitachi Works, Hitachi-GE Nuclear Energy, Ltd., Hitachi-shi, Ibaraki-ken (Japan); Suzuki, Yasuhiko [Measuring Systems Engineering Dept., Hitachi Aloka Medical, Ltd., Ome-shi, Tokyo (Japan); Umegaki, Kikuo [Faculty of Engineering, Hokkaido University, Sapporo-shi, Hokkaido (Japan)

    2016-06-21

    We developed a pinhole gamma camera to measure distributions of radioactive material contaminants and to identify radionuclides in extraordinarily high dose regions (1000 mSv/h). The developed gamma camera is characterized by: (1) tolerance for high dose rate environments; (2) high spatial and spectral resolution for identifying unknown contaminating sources; and (3) good usability for being carried on a robot and remotely controlled. These are achieved by using a compact pixelated detector module with CdTe semiconductors, efficient shielding, and a fine resolution pinhole collimator. The gamma camera weighs less than 100 kg, and its field of view is an 8 m square in the case of a distance of 10 m and its image is divided into 256 (16×16) pixels. From the laboratory test, we found the energy resolution at the 662 keV photopeak was 2.3% FWHM, which is enough to identify the radionuclides. We found that the count rate per background dose rate was 220 cps h/mSv and the maximum count rate was 300 kcps, so the maximum dose rate of the environment where the gamma camera can be operated was calculated as 1400 mSv/h. We investigated the reactor building of Unit 1 at the Fukushima Dai-ichi Nuclear Power Plant using the gamma camera and could identify the unknown contaminating source in the dose rate environment that was as high as 659 mSv/h.

  4. A PREPROCESSING LS-CMA IN HIGHLY CORRUPTIVE ENVIRONMENT

    Institute of Scientific and Technical Information of China (English)

    Guo Yan; Fang Dagang; Thomas N.C.Wang; Liang Changhong

    2002-01-01

    A fast preprocessing Least Square-Constant Modulus Algorithm (LS-CMA) is proposed for blind adaptive beamforming. This new preprocessing method precludes noise capture caused by the original LS-CMA with the preprocessing procedure controlled by the static Constant Modulus Algorithm (CMA). The simulation results have shown that the proposed fast preprocessing LS-CMA can effectively reject the co-channel interference, and quickly lock onto the constant modulus desired signal with only one snapshot in a highly corruptive environment.

  5. 海洋环境要素综合影响下混凝土中氯离子的传输模型%Chloride Ion Transport Model in Concrete Under Combined Influence of Marine Environment Factors

    Institute of Scientific and Technical Information of China (English)

    练继建; 张杰; 吴慕丹; 王海军

    2016-01-01

    In order to clarify the various marine environment factors that affect the chloride ion erosion,by means of analyzing chloride ion erosion mechanism in reinforced concrete,chloride ion transport calculation model under the marine environment including sunshine,tide and temperature was established. Based on the convection-diffusion transmission model,this model was applied to dynamically coupling calculation of temperature field,humidity field and chlorine ion concentration field in the whole life cycle of concrete structures using finite difference method. In the model,the ASHRAE model was plugged in,and the differencesof moisture diffusion and physical field boundary conditions in dry-wet process caused by tidal water level cycles were considered. The ratio of chloride ion to pore fluid was taken as concentration index. The calculated results of every module were validated by test data,and showed good agreement. The model may provide valuable references for marine concrete durability design.%为澄清多种海洋环境要素对混凝土氯离子侵蚀的综合影响,在对混凝土氯离子侵蚀机理分析的基础上,建立了日照、潮汐、气温等海洋环境综合影响下的混凝土氯离子传输计算模型.该模型在传统对流-扩散模型中增加了ASHRAE晴空日照模型,并考虑了潮汐水位的周期变化导致的干湿两个过程中水分扩散以及水-土界面扩散等边界条件的差异,采取氯离子相对孔隙液的浓度作为控制指标,运用有限差分法,对海上混凝土结构全生命周期内的温度场、湿度场、氯离子浓度场进行动态耦合计算.通过试验实测数据对各模块计算结果进行验证,吻合良好.该模型对于海工混凝土的耐久性设计具有参考价值.

  6. Improvement of the High Chloride Drilling Wastewater with Low COD Analysis Method%高氯钻井废水低COD分析方法改进*

    Institute of Scientific and Technical Information of China (English)

    张晓刚; 张淑侠; 雷亮; 何焕杰; 吕宁超; 张鑫; 郭民乐

    2013-01-01

      Significant error occur as COD of the high chloride drilling wastewater with low COD in the gas-oil field was determined using the K2Cr2O7 method. The method with low concentration of oxidant and increasing Hg2SO4 to masking chloride reduced COD analysis error. Experimental results show that when using 0.050 0 mol/L K2Cr2O7 solution and the mass ratio of Hg2SO4 and Cl–was 10∶1,the relative error of COD determination results was less than 10%. This method is suitable for determination of the high chloride drilling wastewater with low COD and expands the range of national standard method.%  用重铬酸钾法测定油气田高氯低COD的钻井废水时会产生较大误差。对该国标法测定COD进行了改进,采用低浓度氧化剂,增加硫酸汞以掩蔽氯离子来降低COD的分析误差。实验结果表明,选择0.0500 mol/L的重铬酸钾溶液,硫酸汞与氯质量比为10︰1时,测定结果的相对误差小于10%,适合测定高氯低COD钻井废水的COD值。该方法扩大了国标法的适用范围。

  7. Climate and Geomorphic Risks in High-Mountain Environments

    Science.gov (United States)

    Huggel, Christian; Kääb, Andreas; Schneider, Jean

    2010-03-01

    Glacier Hazards, Permafrost Hazards, and Glacier Lake Outburst Floods in Mountain Areas: Processes, Assessment, Prevention, Mitigation; Vienna, Austria, 10-13 November 2009; Recent atmospheric warming is profoundly affecting high-mountain environments around the world. Glaciers are thinning and retreating, new and often unstable lakes are forming at glacier margins, other lakes are suddenly draining, and permafrost is degrading. These changes pose serious hazards to people and property in mountain valleys. Several tens of thousands of people were killed by landslides, floods, and debris flows from high-mountain regions during the twentieth century, and there is concern that such events will increase as temperatures warm through the 21st century.

  8. Work environment characteristics of high-quality home health agencies.

    Science.gov (United States)

    Tullai-McGuinness, Susan; Riggs, Jennifer S; Farag, Amany A

    2011-10-01

    This concurrent mixed-method study examines the nurse work environment of high-quality Medicare-certified home health agencies. High-quality (n=6) and low-quality (n=6) home health agencies were recruited using agency-level publicly reported patient outcomes. Direct care registered nurses (RNs) from each agency participated in a focus group and completed the Practice Environment Scale of the Nurse Work Index (PES-NWI). No significant differences were found in the PES-NWI results between nurses working in high- and low-quality agencies, though nurses in high-quality agencies scored higher on all subscales. Nurses working in all the high-quality agencies identified themes of adequate staffing, supportive managers, and team work. These themes were not consistently identified in low-quality agencies. Themes of supportive managers and team work are reflective of effective leadership at the manager level. Agencies struggling to improve quality of care might consider developing their managers' leadership skills.

  9. Thin Film Ceramic Strain Sensor Development for High Temperature Environments

    Science.gov (United States)

    Wrbanek, John D.; Fralick, Gustave C.; Gonzalez, Jose M.; Laster, Kimala L.

    2008-01-01

    The need for sensors to operate in harsh environments is illustrated by the need for measurements in the turbine engine hot section. The degradation and damage that develops over time in hot section components can lead to catastrophic failure. At present, the degradation processes that occur in the harsh hot section environment are poorly characterized, which hinders development of more durable components, and since it is so difficult to model turbine blade temperatures, strains, etc, actual measurements are needed. The need to consider ceramic sensing elements is brought about by the temperature limits of metal thin film sensors in harsh environments. The effort at the NASA Glenn Research Center (GRC) to develop high temperature thin film ceramic static strain gauges for application in turbine engines is described, first in the fan and compressor modules, and then in the hot section. The near-term goal of this research effort was to identify candidate thin film ceramic sensor materials and provide a list of possible thin film ceramic sensor materials and corresponding properties to test for viability. A thorough literature search was conducted for ceramics that have the potential for application as high temperature thin film strain gauges chemically and physically compatible with the NASA GRCs microfabrication procedures and substrate materials. Test results are given for tantalum, titanium and zirconium-based nitride and oxynitride ceramic films.

  10. High-Performance, Radiation-Hardened Electronics for Space Environments

    Science.gov (United States)

    Keys, Andrew S.; Watson, Michael D.; Frazier, Donald O.; Adams, James H.; Johnson, Michael A.; Kolawa, Elizabeth A.

    2007-01-01

    The Radiation Hardened Electronics for Space Environments (RHESE) project endeavors to advance the current state-of-the-art in high-performance, radiation-hardened electronics and processors, ensuring successful performance of space systems required to operate within extreme radiation and temperature environments. Because RHESE is a project within the Exploration Technology Development Program (ETDP), RHESE's primary customers will be the human and robotic missions being developed by NASA's Exploration Systems Mission Directorate (ESMD) in partial fulfillment of the Vision for Space Exploration. Benefits are also anticipated for NASA's science missions to planetary and deep-space destinations. As a technology development effort, RHESE provides a broad-scoped, full spectrum of approaches to environmentally harden space electronics, including new materials, advanced design processes, reconfigurable hardware techniques, and software modeling of the radiation environment. The RHESE sub-project tasks are: SelfReconfigurable Electronics for Extreme Environments, Radiation Effects Predictive Modeling, Radiation Hardened Memory, Single Event Effects (SEE) Immune Reconfigurable Field Programmable Gate Array (FPGA) (SIRF), Radiation Hardening by Software, Radiation Hardened High Performance Processors (HPP), Reconfigurable Computing, Low Temperature Tolerant MEMS by Design, and Silicon-Germanium (SiGe) Integrated Electronics for Extreme Environments. These nine sub-project tasks are managed by technical leads as located across five different NASA field centers, including Ames Research Center, Goddard Space Flight Center, the Jet Propulsion Laboratory, Langley Research Center, and Marshall Space Flight Center. The overall RHESE integrated project management responsibility resides with NASA's Marshall Space Flight Center (MSFC). Initial technology development emphasis within RHESE focuses on the hardening of Field Programmable Gate Arrays (FPGA)s and Field Programmable Analog

  11. Effects of High Magneto-Gravitational Environment on Silkworm Embryogenesis

    Science.gov (United States)

    Tian, Zongcheng; Li, Muwang; Qian, Airong; Xu, Huiyun; Wang, Zhe; Di, Shengmeng; Yang, Pengfei; Hu, Lifang; Ding, Chong; Zhang, Wei; Luo, Mingzhi; Han, Jing; Gao, Xiang; Huang, Yongping; Shang, Peng

    2010-04-01

    The objective of this research was to observe whether silkworm embryos can survive in a high magneto-gravitational environment (HMGE) and what significant phenotype changes can be produced. The hatching rate, hatching time, life span, growth velocity and cocoon weight of silkworm were measured after silkworm embryos were exposed to HMGE (0 g, 12 T; 1 g, 16 T; and 2 g, 12 T) for a period of time. Compared with the control group, 0 g exposure resulted in a lower hatching rate and a shorter life span. Statistically insignificant morphological changes had been observed for larvae growth velocity, incidence of abnormal markings and weight of cocoons. These results suggest that the effect of HMGE on silkworm embryogenesis is not lethal. Bio-effects of silkworm embryogenesis at 0 g in a HMGE were similar with those of space flight. The hatching time, life span and hatching rates of silkworm may be potential phenotype markers related to exposure in a weightless environment.

  12. Neutrophilic iron oxidizers adapted to highly oxic environments

    DEFF Research Database (Denmark)

    Gülay, Arda; Musovic, Sanin; Albrechtsen, Hans-Jørgen;

    of iron oxidizing bacterial in the highly oxic environments found in typical rapid sand filters. The neutrophilic FeOB were enriched by the Fe2+/O2 opposing gradient technique and quantified by MPN methodology. Diversity fingerprints of the enrichment cultures were obtained with a 16S rRNA targeted DGGE...... oxidation of iron would be retarded. For that reason, no attempts have been documented to describe the density and diversity of iron oxidizing bacteria (FeOB) in oxic neutrophilic environments. Under low temperatures (5 to 10°C) conditions, as typically found in groundwater, extremely low rates of chemical...... technique, and dominant bands were isolated and sequenced for identification of dominant enrichment members. Enrichment were microscopically examined via CSLM in combination with FeOB specific or generic cytostains to verify enrichments, check cell morphologies and quantify cell densities. Our results...

  13. Using Highly Interactive Virtual Environments for Safeguards Activities

    Energy Technology Data Exchange (ETDEWEB)

    Weil, Bradley S [ORNL; Alcala, Benjamin S [ORNL; Alcala, Scott [ORNL; Eipeldauer, Mary D [ORNL; Weil, Logan B [ORNL

    2010-01-01

    Highly interactive virtual environment (HIVE) is a term that refers to interactive educational simulations, serious games and virtual worlds. Studies indicate that learning with the aid of interactive environments produces better retention and depth of knowledge by promoting improved trainee engagement and understanding. Virtual reality or three dimensional (3D) visualization is often used to promote the understanding of something when personal observation, photographs, drawings, and/or sketches are not possible or available. Subjects and situations, either real or hypothetical, can be developed using a 3D model. Models can be tailored to the audience allowing safeguards and security features to be demonstrated for educational purposes in addition to engineering evaluation and performance analysis. Oak Ridge National Laboratory (ORNL) has begun evaluating the feasibility of HIVEs for improving safeguards activities such as training, mission planning, and evaluating worker task performance. This paper will discuss the development workflow of HIVEs and present some recent examples.

  14. Decision making in high-velocity environments: implications for healthcare.

    Science.gov (United States)

    Stepanovich, P L; Uhrig, J D

    1999-01-01

    Healthcare can be considered a high-velocity environment and, as such, can benefit from research conducted in other industries regarding strategic decision making. Strategic planning is not only relevant to firms in high-velocity environments, but is also important for high performance and survival. Specifically, decision-making speed seems to be instrumental in differentiating between high and low performers; fast decision makers outperform slow decision makers. This article outlines the differences between fast and slow decision makers, identifies five paralyses that can slow decision making in healthcare, and outlines the role of a planning department in circumventing these paralyses. Executives can use the proposed planning structure to improve both the speed and quality of strategic decisions. The structure uses planning facilitators to avoid the following five paralyses: 1. Analysis. Decision makers can no longer afford the luxury of lengthy, detailed analysis but must develop real-time systems that provide appropriate, timely information. 2. Alternatives. Many alternatives (beyond the traditional two or three) need to be considered and the alternatives must be evaluated simultaneously. 3. Group Think. Decision makers must avoid limited mind-sets and autocratic leadership styles by seeking out independent, knowledgeable counselors. 4. Process. Decision makers need to resolve conflicts through "consensus with qualification," as opposed to waiting for everyone to come on board. 5. Separation. Successful implementation requires a structured process that cuts across disciplines and levels.

  15. Flexible sample environment for high resolution neutron imaging at high temperatures in controlled atmosphere

    DEFF Research Database (Denmark)

    Makowska, Malgorzata G.; Kuhn, Luise Theil; Cleemann, Lars Nilausen

    2015-01-01

    High material penetration by neutrons allows for experiments using sophisticated sample environments providing complex conditions. Thus, neutron imaging holds potential for performing in situ nondestructive measurements on large samples or even full technological systems, which are not possible w...

  16. Chemical Vapor Deposition at High Pressure in a Microgravity Environment

    Science.gov (United States)

    McCall, Sonya; Bachmann, Klaus; LeSure, Stacie; Sukidi, Nkadi; Wang, Fuchao

    1999-01-01

    In this paper we present an evaluation of critical requirements of organometallic chemical vapor deposition (OMCVD) at elevated pressure for a channel flow reactor in a microgravity environment. The objective of using high pressure is to maintain single-phase surface composition for materials that have high thermal decomposition pressure at their optimum growth temperature. Access to microgravity is needed to maintain conditions of laminar flow, which is essential for process analysis. Based on ground based observations we present an optimized reactor design for OMCVD at high pressure and reduced gravity. Also, we discuss non-intrusive real-time optical monitoring of flow dynamics coupled to homogeneous gas phase reactions, transport and surface processes. While suborbital flights may suffice for studies of initial stages of heteroepitaxy experiments in space are essential for a complete evaluation of steady-state growth.

  17. An Efficient Role Specification Management Model for Highly Distributed Environments

    Directory of Open Access Journals (Sweden)

    Soomi Yang

    2006-07-01

    Full Text Available Highly distributed environments such as pervasive computing environments not having global or broad control, need another attribute certificate management technique. For an efficient role based access control using attribute certificate, we use a technique of structuring role specification certificates. It can provide more flexible and secure collaborating environments. The roles are grouped and made them into the relation tree. It can reduce management cost and overhead incurred when changing the specification of the role. Further we use caching of frequently used role specification certificate for better performance in case applying the role. Tree structured role specification results secure and efficient role renewing and distribution. Caching of role specification helps an application of role. In order to be scalable distribution of the role specification certificate, we use multicasting packets. Also, performance enhancement of structuring role specification certificates is quantified in the sense of taking into account of the packet loss. In the experimental section, it is shown that role updating and distribution are secured and efficient.

  18. Management and Performance of APPLE Battery in High Temperature Environment

    Science.gov (United States)

    Suresh, M. S.; Subrahmanyam, A.; Agrawal, B. L.

    1984-01-01

    India's first experimental communication satellite, APPLE, carried a 12 AH Ni-Cd battery for supplying power during eclipse. Failure to deploy one of the two solar panels resulted in the battery operating in a high temperature environment, around 40 C. This also resulted in the battery being used in diurnal cycles rather than just half yearly eclipse seasons. The management and performance of the battery during its life of two years are described. An attempt to identify the probable degradation mechanisms is also made.

  19. Neutrophilic iron oxidizers adapted to highly oxic environments

    DEFF Research Database (Denmark)

    Gülay, Arda; Musovic, Sanin; Albrechtsen, Hans-Jørgen

    indicate that neutrophilic iron oxidizers in highly oxic environments like drinking water treatment systems can be abundant (5 E+04 to 7 E+05 cells per gram of wet sand material). It was furthermore observed that the diversity of the cultivated dominant iron oxidizers differs substantially from those...... carbon) while oxygen (O2) is the electron acceptor provided during the aeration process. Numerous previous studies have described neutrophilic iron oxidizers as a bacterial guild with a special niche preference, especially the transition zone between aerobic and anoxic regions, where abiotic chemical...

  20. 40 CFR 61.63 - Emission standard for vinyl chloride plants.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 8 2010-07-01 2010-07-01 false Emission standard for vinyl chloride... for Vinyl Chloride § 61.63 Emission standard for vinyl chloride plants. An owner or operator of a vinyl chloride plant shall comply with the requirements of this section and § 61.65. (a) Vinyl...

  1. Sensitive determination of melamine in milk and powdered infant formula samples by high-performance liquid chromatography using dabsyl chloride derivatization followed by dispersive liquid-liquid microextraction.

    Science.gov (United States)

    Faraji, M; Adeli, M

    2017-04-15

    A new and sensitive pre-column derivatization with dabsyl chloride followed by dispersive liquid-liquid microextraction was developed for the analysis of melamine (MEL) in raw milk and powdered infant formula samples by high performance liquid chromatography (HPLC) with visible detection. Derivatization with dabsyl chloride leads to improving sensitivity and hydrophobicity of MEL. Under optimum conditions of derivatization and microextraction steps, the method yielded a linear calibration curve ranging from 1.0 to 500μgL(-1) with a determination coefficient (R(2)) of 0.9995. Limit of detection and limit of quantification were 0.1 and 0.3μgL(-1), respectively. The relative standard deviation (RSD%) for intra-day (repeatability) and inter-day (reproducibility) at 25 and 100μgL(-1) levels of MEL was less than 7.0% (n=6). Finally, the proposed method was successfully applied for the preconcentration and determination of MEL in different raw milk and powdered infant formula, and satisfactory results were obtained (relative recovery ⩾94%).

  2. Highly efficient palladium precatalysts of homoscorpionate bispyrazolyl ligands for the more challenging Suzuki-Miyaura cross-coupling of aryl chlorides.

    Science.gov (United States)

    John, Alex; Shaikh, Mobin M; Butcher, Ray J; Ghosh, Prasenjit

    2010-08-21

    Highly efficient palladium precatalysts {[RN{-(CH(2))(n)-pz(3,5-Me)(2)}(2)]PdCl(2)}(m) [m = n = 1; R = 2,6-Me(2)C(6)H(3) (1), 2,4,6-Me(3)C(6)H(2) (2), CH(2)Ph (3) and m = n = 2; R = CH(2)Ph (4)] of a series of homoscorpionate bispyrazolyl ligands for the Suzuki-Miyaura cross-coupling of the more challenging aryl chloride substrates are reported. In particular, the palladium 1-4 precatalysts carried out the Suzuki-Miyaura cross-coupling of a wide variety of aryl chloride substrates bearing electron withdrawing, electron donating and heteroaryl substituents. Remarkably enough, the molecular structure determination of the 1-4 precatalysts by X-ray diffraction studies revealed the presence of anagostic [C-H...Pd] type interactions in the mononuclear 1-3 complexes of methylene bridged bispyrazolyl ligands whereas the ethylene bridged analog 4 yielded an interesting dimeric 20-membered macrometallacyclic complex devoid of any such interaction.

  3. High temperature, harsh environment sensors for advanced power generation systems

    Science.gov (United States)

    Ohodnicki, P. R.; Credle, S.; Buric, M.; Lewis, R.; Seachman, S.

    2015-05-01

    One mission of the Crosscutting Technology Research program at the National Energy Technology Laboratory is to develop a suite of sensors and controls technologies that will ultimately increase efficiencies of existing fossil-fuel fired power plants and enable a new generation of more efficient and lower emission power generation technologies. The program seeks to accomplish this mission through soliciting, managing, and monitoring a broad range of projects both internal and external to the laboratory which span sensor material and device development, energy harvesting and wireless telemetry methodologies, and advanced controls algorithms and approaches. A particular emphasis is placed upon harsh environment sensing for compatibility with high temperature, erosive, corrosive, and highly reducing or oxidizing environments associated with large-scale centralized power generation. An overview of the full sensors and controls portfolio is presented and a selected set of current and recent research successes and on-going projects are highlighted. A more detailed emphasis will be placed on an overview of the current research thrusts and successes of the in-house sensor material and device research efforts that have been established to support the program.

  4. Silicon Sensors for Trackers at High-Luminosity Environment

    CERN Document Server

    Peltola, Timo

    2015-01-01

    The planned upgrade of the LHC accelerator at CERN, namely the high luminosity (HL) phase of the LHC (HL-LHC foreseen for 2023), will result in a more intense radiation environment than the present tracking system was designed for. The required upgrade of the all-silicon central trackers at the ALICE, ATLAS, CMS and LHCb experiments will include higher granularity and radiation hard sensors. The radiation hardness of the new sensors must be roughly an order of magnitude higher than the one of LHC detectors. To address this, a massive R&D program is underway within the CERN RD50 collaboration "Development of Radiation Hard Semiconductor Devices for Very High Luminosity Colliders" to develop silicon sensors with sufficient radiation tolerance. Research topics include the improvement of the intrinsic radiation tolerance of the sensor material and novel detector designs with benefits like reduced trapping probability (thinned and 3D sensors), maximized sensitive area (active edge sensors) and enhanced charge ...

  5. In situ Raman and synchrotron X-ray diffraction study on crystallization of Choline chloride/Urea deep eutectic solvent under high pressure

    Science.gov (United States)

    Yuan, Chaosheng; Chu, Kunkun; Li, Haining; Su, Lei; Yang, Kun; Wang, Yongqiang; Li, Xiaodong

    2016-09-01

    Pressure-induced crystallization of Choline chloride/Urea (ChCl/Urea) deep eutectic solvent (DES) has been investigated by in-situ Raman spectroscopy and synchrotron X-ray diffraction. The results indicated that high pressure crystals appeared at around 2.6 GPa, and the crystalline structure was different from that formed at ambient pressure. Upon increasing the pressure, the Nsbnd H stretching modes of Urea underwent dramatic change after liquid-solid transition. It appears that high pressures may enhance the hydrogen bonds formed between ChCl and Urea. P versus T phase diagram of ChCl/Urea DES was constructed, and the crystallization mechanism of ChCl/Urea DES was discussed in view of hydrogen bonds.

  6. High efficiency chlorine removal from polyvinyl chloride (PVC) pyrolysis with a gas-liquid fluidized bed reactor.

    Science.gov (United States)

    Yuan, G; Chen, D; Yin, L; Wang, Z; Zhao, L; Wang, J Y

    2014-06-01

    In this research a gas-liquid fluidized bed reactor was developed for removing chlorine (Cl) from polyvinyl chloride (PVC) to favor its pyrolysis treatment. In order to efficiently remove Cl within a limited time before extensive generation of hydrocarbon products, the gas-liquid fluidized bed reactor was running at 280-320 °C, where hot N2 was used as fluidizing gas to fluidize the molten polymer, letting the molten polymer contact well with N2 to release Cl in form of HCl. Experimental results showed that dechlorination efficiency is mainly temperature dependent and 300 °C is a proper reaction temperature for efficient dechlorination within a limited time duration and for prevention of extensive pyrolysis; under this temperature 99.5% of Cl removal efficiency can be obtained within reaction time around 1 min after melting is completed as the flow rate of N2 gas was set around 0.47-0.85 Nm(3) kg(-1) for the molten PVC. Larger N2 flow rate and additives in PVC would enhance HCl release but did not change the final dechlorination efficiency; and excessive N2 flow rate should be avoided for prevention of polymer entrainment. HCl is emitted from PVC granules or scraps at the mean time they started to melt and the melting stage should be taken into consideration when design the gas-liquid fluidized bed reactor for dechlorination.

  7. A High Performance Theory for Thermodynamic Study on the Binding of Human Serum Albumin with Erbium Chloride

    Institute of Scientific and Technical Information of China (English)

    BEHBEHANI G Rezaei; DIVSALAR A; SABOURY A. A; FARIDBOD, F; GANJALI M R

    2009-01-01

    A thermodynamic study of the interaction between erbium(Ⅲ) chloride (Er3+) and human serum albumin (HAS) was studied at pH=7.0, 27 and 37℃ in phosphate buffer by isothermal titration calorimetry (ITC). The present study reports the thermodynamic parameters that govern HAS-Er3+ interactions. The extended solvation theory was used to reproduce the enthalpies of HAS-Er3+ interactions over the whole range of Er3+ concentrations. The bind-ing parameters recovered from the new model were attributed to the structural change of HAS and its biological ac-tivity. The results obtained indicate that there is a set of two identical binding sites for Er3+ ions with negative co-operativity. The enhancement of complex formation by Er3+ and concomitant increase in △S suggest that the metal ion plays a role in increasing the number of hydrophobic contacts. The binding parameters discovered from the ex-tended solvation model indicate that the stability of HAS molecule is increased as a result of its interaction with Er3+ ions.

  8. Silicon sensors for trackers at high-luminosity environment

    Energy Technology Data Exchange (ETDEWEB)

    Peltola, Timo, E-mail: timo.peltola@helsinki.fi

    2015-10-01

    The planned upgrade of the LHC accelerator at CERN, namely the high luminosity (HL) phase of the LHC (HL-LHC foreseen for 2023), will result in a more intense radiation environment than the present tracking system that was designed for. The required upgrade of the all-silicon central trackers at the ALICE, ATLAS, CMS and LHCb experiments will include higher granularity and radiation hard sensors. The radiation hardness of the new sensors must be roughly an order of magnitude higher than in the current LHC detectors. To address this, a massive R&D program is underway within the CERN RD50 Collaboration “Development of Radiation Hard Semiconductor Devices for Very High Luminosity Colliders” to develop silicon sensors with sufficient radiation tolerance. Research topics include the improvement of the intrinsic radiation tolerance of the sensor material and novel detector designs with benefits like reduced trapping probability (thinned and 3D sensors), maximized sensitive area (active edge sensors) and enhanced charge carrier generation (sensors with intrinsic gain). A review of the recent results from both measurements and TCAD simulations of several detector technologies and silicon materials at radiation levels expected for HL-LHC will be presented. - Highlights: • An overview of the recent results from the RD50 collaboration. • Accuracy of TCAD simulations increased by including both bulk and surface damage. • Sensors with n-electrode readout and MCz material offer higher radiation hardness. • 3D detectors are a promising choice for the extremely high fluence environments. • Detectors with an enhanced charge carrier generation under systematic investigation.

  9. Long-term high frequency measurements of ethane, benzene and methyl chloride at Ragged Point, Barbados: Identification of long-range transport events

    Directory of Open Access Journals (Sweden)

    A.T. Archibald

    2015-09-01

    Full Text Available AbstractHere we present high frequency long-term observations of ethane, benzene and methyl chloride from the AGAGE Ragged Point, Barbados, monitoring station made using a custom built GC-MS system. Our analysis focuses on the first three years of data (2005–2007 and on the interpretation of periodic episodes of high concentrations of these compounds. We focus specifically on an exemplar episode during September 2007 to assess if these measurements are impacted by long-range transport of biomass burning and biogenic emissions. We use the Lagrangian Particle Dispersion model, NAME, run forwards and backwards in time to identify transport of air masses from the North East of Brazil during these events. To assess whether biomass burning was the cause we used hot spots detected using the MODIS instrument to act as point sources for simulating the release of biomass burning plumes. Excellent agreement for the arrival time of the simulated biomass burning plumes and the observations of enhancements in the trace gases indicates that biomass burning strongly influenced these measurements. These modelling data were then used to determine the emissions required to match the observations and compared with bottom up estimates based on burnt area and literature emission factors. Good agreement was found between the two techniques highlight the important role of biomass burning. The modelling constrained by in situ observations suggests that the emission factors were representative of their known upper limits, with the in situ data suggesting slightly greater emissions of ethane than the literature emission factors account for. Further analysis was performed concluding only a small role for biogenic emissions of methyl chloride from South America impacting measurements at Ragged Point. These results highlight the importance of long-term high frequency measurements of NMHC and ODS and highlight how these data can be used to determine sources of emissions

  10. Enabling Efficient Climate Science Workflows in High Performance Computing Environments

    Science.gov (United States)

    Krishnan, H.; Byna, S.; Wehner, M. F.; Gu, J.; O'Brien, T. A.; Loring, B.; Stone, D. A.; Collins, W.; Prabhat, M.; Liu, Y.; Johnson, J. N.; Paciorek, C. J.

    2015-12-01

    A typical climate science workflow often involves a combination of acquisition of data, modeling, simulation, analysis, visualization, publishing, and storage of results. Each of these tasks provide a myriad of challenges when running on a high performance computing environment such as Hopper or Edison at NERSC. Hurdles such as data transfer and management, job scheduling, parallel analysis routines, and publication require a lot of forethought and planning to ensure that proper quality control mechanisms are in place. These steps require effectively utilizing a combination of well tested and newly developed functionality to move data, perform analysis, apply statistical routines, and finally, serve results and tools to the greater scientific community. As part of the CAlibrated and Systematic Characterization, Attribution and Detection of Extremes (CASCADE) project we highlight a stack of tools our team utilizes and has developed to ensure that large scale simulation and analysis work are commonplace and provide operations that assist in everything from generation/procurement of data (HTAR/Globus) to automating publication of results to portals like the Earth Systems Grid Federation (ESGF), all while executing everything in between in a scalable environment in a task parallel way (MPI). We highlight the use and benefit of these tools by showing several climate science analysis use cases they have been applied to.

  11. The single event upset environment for avionics at high latitude

    Energy Technology Data Exchange (ETDEWEB)

    Sims, A.J.; Dyer, C.S.; Peerless, C.L. (Defence Research Agency, Farnborough (United Kingdom). Space and Communications Dept.); Johansson, K.; Pettersson, H. (SAAB Military Aircraft, Linkoeping (Sweden)); Farren, J. (AEA Technology, Oxfordshire (United Kingdom). Harwell Lab.)

    1994-12-01

    Modern avionic systems for civil and military applications are becoming increasingly reliant upon embedded microprocessors and associated memory devices. The phenomenon of single event upset (SEU) is well known in space systems and designers have generally been careful to use SEU tolerant devices or to implement error detection and correction (EDAC) techniques where appropriate. In the past, avionics designers have had no reason to consider SEU effects but is clear that the more prevalent use of memory devices combined with increasing levels of IC integration will make SEU mitigation an important design consideration for future avionic systems. To this end, it is necessary to work towards producing models of the avionics SEU environment which will permit system designers to choose components and EDAC techniques which are based on predictions of SEU rates correct to much better than an order of magnitude. Measurements of the high latitude SEU environment at avionics altitude have been made on board a commercial airliner. Results are compared with models of primary and secondary cosmic rays and atmospheric neutrons. Ground based SEU tests of static RAMs are used to predict rates in flight.

  12. Extracting third order optical nonlinearities of Mn(III)-Phthalocyanine chloride using high repetition rate femtosecond pulses

    Science.gov (United States)

    Makhal, Krishnandu; Mathur, Paresh; Maurya, Sidharth; Goswami, Debabrata

    2017-02-01

    Third order nonlinearities of Mn(III)-Phthalocyanine chloride in dimethyl-sulphoxide under 50 fs pulses, operating at 94 MHz, by eliminating cumulative thermal effects have been investigated and reported by us. Modifications were done in data acquisition during Z-scan experiment, which included recording of time evolution waveform traces in an oscilloscope and not collection of Z versus transmission and utilization of a chopper of a suitable duty cycle. Time evolution traces were further processed analytically through MatLab® programming, which yielded Z-scan traces similar to what was obtained with single shot 50 fs pulse. We observed reverse saturable absorption at 800 nm owing to excited state absorption. We show that the nonlinear refractive index (γ) and nonlinear absorption coefficient (β) are over estimated almost 100 times, when MHz pulses are used compared to a situation, where thermo-optical nonlinearities are accounted. Illumination and dark periods are carefully set in a way, so that the sample is able to completely recover its initial temperature before arrival of the next pulse. Magnitudes of γ and β were found to be -(6.5-4.9) × 10-16 m2/W and (5.4-6.2) × 10-10 m/W under the MHz condition, whereas they were -(0.18-2.2) × 10-18 m2/W and (9.5-15) × 10-12 m/W under the thermally managed condition, respectively. To reveal the associated fast nonlinearity, femtosecond transient absorption experiment was performed, which inferred excited state absorption and ground state bleaching across the 450-780 nm region. Dynamics associated with these processes are reported along with fluorescence lifetime obtained through the TCSPC technique. Structure optimization using TDDFT calculations and HOMO-LUMO gaps with orbital pictures are also shown.

  13. High Molecular Weight Petrogenic and Pyrogenic Hydrocarbons in Aquatic Environments

    Science.gov (United States)

    Abrajano, T. A., Jr.; Yan, B.; O'Malley, V.

    2003-12-01

    Geochemistry is ultimately the study of sources, movement, and fate of chemicals in the geosphere at various spatial and temporal scales. Environmental organic geochemistry focuses such studies on organic compounds of toxicological and ecological concern (e.g., Schwarzenbach et al., 1993, 1998; Eganhouse, 1997). This field emphasizes not only those compounds with potential toxicological properties, but also the geological systems accessible to the biological receptors of those hazards. Hence, the examples presented in this chapter focus on hydrocarbons with known health and ecological concern in accessible shallow, primarily aquatic, environments.Modern society depends on oil for energy and a variety of other daily needs, with present mineral oil consumption throughout the 1990s exceeding 3×109 t yr-1 (NRC, 2002). In the USA, e.g., ˜40% of energy consumed and 97% of transportation fuels are derived from oil. In the process of extraction, refinement, transport, use, and waste production, a small but environmentally significant fraction of raw oil materials, processed products, and waste are released inadvertently or purposefully into the environment. Because their presence and concentration in the shallow environments are often the result of human activities, these organic materials are generally referred to as "environmental contaminants." Although such reference connotes some form of toxicological or ecological hazard, specific health or ecological effects of many organic "environmental contaminants" remain to be demonstrated. Some are, in fact, likely innocuous at the levels that they are found in many systems, and simply adds to the milieu of biogenic organic compounds that naturally cycle through the shallow environment. Indeed, virtually all compounds in crude oil and processed petroleum products have been introduced naturally to the shallow environments as oil and gas seepage for millions of years ( NRC, 2002). Even high molecular weight (HMW) polyaromatic

  14. Characterization of coaxial rocket injector sprays under high pressure environments

    Science.gov (United States)

    Sankar, S. V.; Wang, G.; Brena De La Rosa, A.; Rudoff, R. C.; Isakovic, A.; Bachalo, W. D.

    1992-01-01

    The effect of elevated environment pressures on the atomization characteristics of a single element, scaled-down, shear-coaxial rocket injector has been investigated. In this study, the shear coaxial injector was operated with water and air as simulants for conventionally used liquid oxygen and hydrogen gas, respectively. The experiments were conducted in a specially designed high pressure rig. A two-component PDPA/DSA system was used to study the spray characteristics at different chamber pressures ranging from atmospheric to 100 psig. The study showed an overall increase in the droplet sizes at higher chamber pressures. This phenomenon is attributed to a decrease in the secondary atomization effects at higher chamber pressures which, in turn, is directly related to a decrease in the shear experienced by the droplets as they move axially through the pressure chamber.

  15. A highly selective fluorescent sensor for Cu{sup 2+} based on 2-(2'-hydroxyphenyl)benzoxazole in a poly(vinyl chloride) matrix

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Xiaobing [State Key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha, 410082 (China); Peng Jing [State Key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha, 410082 (China); He Chunlian [Medical college, Hunan Normal University, Changsha 410006 (China); Shen Guoli [State Key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha, 410082 (China); Yu Ruqin [State Key Laboratory of Chemo/Biosensing and Chemometrics, College of Chemistry and Chemical Engineering, Hunan University, Changsha, 410082 (China)]. E-mail: rqyu@hnu.cn

    2006-05-17

    This paper describes a copper selective optical chemical sensor based on static quenching of the fluorescence of 2-(2'-hydroxyphenyl)benzoxazole entrapped in a poly(vinyl chloride) (PVC) membrane. The effect of the composition of the sensing membrane was studied, and experimental conditions were optimized. The sensors exhibit stable response over the concentration range from 4.0 x 10{sup -8} M to 5.0 x 10{sup -5} M Cu{sup 2+} at pH 4.0-6.5, and a high selectivity. The response time for Cu{sup 2+} with concentration {<=}5 x 10{sup -6} M is less than 7 min. The optode can be regenerated using 0.1 M HCl and acetate buffer solution. The sensor has been used for direct measurement of copper content in river water samples with a relative error less than 4% with reference to that obtained by atomic absorption spectrometry.

  16. Synthesis and Properties of High Strength Thin Film Composites of Poly(ethylene Oxide and PEO-PMMA Blend with Cetylpyridinium Chloride Modified Clay

    Directory of Open Access Journals (Sweden)

    Mohammad Saleem Khan

    2015-01-01

    Full Text Available Ion-conducting thin film composites of polymer electrolytes were prepared by mixing high MW poly(ethylene oxide (PEO, poly(methyl methacrylate (PMMA as a polymer matrix, cetylpyridinium chloride (CPC modified MMT as filler, and different content of LiClO4 by using solution cast method. The crystallinity, ionic conductivity (σ, and mechanical properties of the composite electrolytes and blend composites were evaluated by using XRD, AC impedance, and UTM studies, respectively. The modification of clay by CPC showed enhancement in the d-spacing. The loading of clay has effect on crystallinity of PEO systems. Blend composites showed better mechanical properties. Young’s modulus and elongation at break values showed increase with salt and clay incorporation in pure PEO. The optimum composition composite of PEO with 3.5 wt% of salt and 3.3 wt% of CPMMT exhibited better performance.

  17. Telomerization of Vinyl Chloride with Chloroform Initiated by Ferrous Chloride-Dimethylacetamide under Ultrasonic Conditions

    Directory of Open Access Journals (Sweden)

    Hua Qian

    2015-01-01

    Full Text Available Telomerization of vinyl chloride with chloroform was investigated using ferrous chloride-dimethylacetamide system, and 42.1% yield, more than four times the one reported before, was achieved. The addition of ultrasound further improved the reaction and yield was raised to 51.9% with trace byproducts at highly reduced reaction time and temperature. Ferrous chloride-dimethylacetamide under ultrasonic irradiation acts as a very efficient catalyst system for the 1 : 1 telomerization.

  18. A high resolution pneumatic stepping actuator for harsh reactor environments

    Science.gov (United States)

    Tippetts, Thomas B.; Evans, Paul S.; Riffle, George K.

    1993-01-01

    A reactivity control actuator for a high-power density nuclear propulsion reactor must be installed in close proximity to the reactor core. The energy input from radiation to the actuator structure could exceed hundreds of W/cc unless low-cross section, low-absorptivity materials are chosen. Also, for post-test handling and subsequent storage, materials should not be used that are activated into long half-life isotopes. Pneumatic actuators can be constructed from various reactor-compatible materials, but conventional pneumatic piston actuators generally lack the stiffness required for high resolution reactivity control unless electrical position sensors and compensated electronic control systems are used. To overcome these limitations, a pneumatic actuator is under development that positions an output shaft in response to a series of pneumatic pulses, comprising a pneumatic analog of an electrical stepping motor. The pneumatic pulses are generated remotely, beyond the strong radiation environment, and transmitted to the actuator through tubing. The mechanically simple actuator uses a nutating gear harmonic drive to convert motion of small pistons directly to high-resolution angular motion of the output shaft. The digital nature of this actuator is suitable for various reactor control algorithms but is especially compatible with the three bean salad algorithm discussed by Ball et al. (1991).

  19. High resolution study of the ν2 and ν5 rovibrational fundamental bands of thionyl chloride: Interplay of an evolutionary algorithm and a line-by-line analysis

    Science.gov (United States)

    Roucou, Anthony; Dhont, Guillaume; Cuisset, Arnaud; Martin-Drumel, Marie-Aline; Thorwirth, Sven; Fontanari, Daniele; Meerts, W. Leo

    2017-08-01

    The ν2 and ν5 fundamental bands of thionyl chloride (SOCl2) were measured in the 420 cm-1-550 cm-1 region using the FT-far-IR spectrometer exploiting synchrotron radiation on the AILES beamline at SOLEIL. A straightforward line-by-line analysis is complicated by the high congestion of the spectrum due to both the high density of SOCl2 rovibrational bands and the presence of the ν2 fundamental band of sulfur dioxide produced by hydrolysis of SOCl2 with residual water. To overcome this difficulty, our assignment procedure for the main isotopologues 32S16O35Cl2 and 32S16O35Cl37Cl alternates between a direct fit of the spectrum, via a global optimization technique, and a traditional line-by-line analysis. The global optimization, based on an evolutionary algorithm, produces rotational constants and band centers that serve as useful starting values for the subsequent spectroscopic analysis. This work helped to identify the pure rotational submillimeter spectrum of 32S16O35Cl2 in the v2=1 and v5=1 vibrational states of Martin-Drumel et al. [J. Chem. Phys. 144, 084305 (2016)]. As a by-product, the rotational transitions of the v4=1 far-IR inactive state were identified in the submillimeter spectrum. A global fit gathering all the microwave, submillimeter, and far-IR data of thionyl chloride has been performed, showing that no major perturbation of rovibrational energy levels occurs for the main isotopologue of the molecule.

  20. Cryogenic Impinging Jets Subjected to High Frequency Transverse Acoustic Forcing in a High Pressure Environment

    Science.gov (United States)

    2016-07-27

    Forcing in a High Pressure Environment 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Mario Roa, S. Alex Schumaker...disclose the work. PA Clearance Number: 16308 Clearance Date: 6/17/2016 13. SUPPLEMENTARY NOTES For presentation at AIAA Propulsion and Energy; Salt...the coupling between the impact waves created by impinging jets and high frequency acoustic pressure perturbations. High speed, backlit imaging was

  1. The importance of chloride sensors stability in monitoring ageing phenomena in concrete structures: Ag/AgCl electrodes performance in simulated pore-water environment

    NARCIS (Netherlands)

    Pargar, F.; Koleva, D.A.; Koenders, E.A.B.; Van Breugel, K.

    2014-01-01

    One of the reported problems associated with the performance of Ag/AgCl electrodes in alkaline environment, as concrete pore water, has been their poor stability. Open circuit potentials are typically observed to be stable for a time period of a few minutes to some days depending on the thickness

  2. Study on Repair Effect of Corroded Reinforced Concrete Under Chloride Environment%氯盐环境下已锈蚀钢筋混凝土修复效果研究∗

    Institute of Scientific and Technical Information of China (English)

    施后军; 耿欧; 刘颖凤

    2015-01-01

    钢筋的锈蚀是混凝土耐久性失效的主要原因,阻止钢筋锈蚀对于保证混凝土结构使用寿命具有重要意义。为提高氯盐侵蚀环境下已锈蚀钢筋混凝土构件的无损修复效果,对不同锈蚀程度的钢筋混凝土试件分别采用电化学除氯和涂刷渗透型迁移性钢筋阻锈剂的方法进行修复试验,测试了修复后的钢筋锈蚀电流密度和锈蚀率等指标,对比分析了两者的修复效果。结果表明,初始锈蚀率较大时,电化学除氯方法阻止钢筋继续锈蚀比涂刷阻锈剂的效果更好。%The corrosion of steel bar in concrete is the main reason for failure of concrete durability, so preventing steel bar corrosion is significant to ensure the durability of concrete and prolong the service life of structure. In order to improve the non⁃destructive repair effect of corroded reinforced concrete members under chloride environment, the reinforced concrete specimens of different corrosion degree were repaired respectively by electrochemical chloride extraction ( ECE ) and coating migrating corrosion inhibitor ( MCI) and the method which worked best would be found through a series of experiments above. This paper tested steel bar corrosion current density and its corrosion rate after repair and so on, and then made a comparative analysis of the repair effect of each repair method. The analysis results showed that when the reinforced initial corrosion rate was higher, the effect of electrochemical chloride extraction in repair of concrete durability was better than the effect of coating migrating corrosion inhibitor.

  3. Silicon sensors for trackers at high-luminosity environment

    Science.gov (United States)

    Peltola, Timo

    2015-10-01

    The planned upgrade of the LHC accelerator at CERN, namely the high luminosity (HL) phase of the LHC (HL-LHC foreseen for 2023), will result in a more intense radiation environment than the present tracking system that was designed for. The required upgrade of the all-silicon central trackers at the ALICE, ATLAS, CMS and LHCb experiments will include higher granularity and radiation hard sensors. The radiation hardness of the new sensors must be roughly an order of magnitude higher than in the current LHC detectors. To address this, a massive R&D program is underway within the CERN RD50 Collaboration "Development of Radiation Hard Semiconductor Devices for Very High Luminosity Colliders" to develop silicon sensors with sufficient radiation tolerance. Research topics include the improvement of the intrinsic radiation tolerance of the sensor material and novel detector designs with benefits like reduced trapping probability (thinned and 3D sensors), maximized sensitive area (active edge sensors) and enhanced charge carrier generation (sensors with intrinsic gain). A review of the recent results from both measurements and TCAD simulations of several detector technologies and silicon materials at radiation levels expected for HL-LHC will be presented.

  4. Cytotoxic effects of nanosilver are highly dependent on the chloride concentration and the presence of organic compounds in the cell culture media.

    Science.gov (United States)

    Kaiser, Jean-Pierre; Roesslein, Matthias; Diener, Liliane; Wichser, Adrian; Nowack, Bernd; Wick, Peter

    2017-01-06

    Nanosilver shows great promise for use in industrial, consumer or medical products because of its antimicrobial properties. However, the underlying mechanisms of the effects of silver nanoparticles on human cells are still controversial. Therefore, in the present study the influence of the chloride concentration and different serum content of culture media on the cytotoxic effects of nanosilver was systematically evaluated. Our results show that nanosilver toxicity was strongly affected by the composition of the culture media. The chloride concentration, as well as the carbon content affected the silver agglomeration and the complex formation. But also the dissolution of nanosilver and the availability of free silver ions (Ag(+)) were severely affected by the compositions of the culture media. Cells, only exposed to silver particles in suspension and dissolved silver complexes, did not show any effects under all conditions. Nanosilver agglomerates and silver complexes were not very soluble. Thus, cells growing on the bottom of the culture dishes were exposed to sedimented nanosilver agglomerates and precipitated silver complexes. Locally, the concentration of silver on the cell surface was very high, much higher compared the silver concentration in the bulk solution. The cytotoxic effects of nanosilver are therefore a combination of precipitated silver complexes and organic silver compounds rather than free silver ions. Silver coatings are used in health care products due to their bacteriostatic or antibacterial properties. The assessment of the toxicity of a certain compound is mostly done using in vitro assays. Therefore, cytotoxicity studies of nanosilver using human cell cultures have to be undertaken under well controlled and understood cultivations conditions in order to improve the compatibility of different studies. Especially when eukaryotic versus prokaryotic systems are compared for the evaluation of the use of nanosilver as antibacterial coatings for

  5. RESEARCH ON HIGH DWELL PRESSURE PERFORMANCE OF BUTYL CHLORIDE RUBBER%氯化丁基橡胶高压气保压性能研究

    Institute of Scientific and Technical Information of China (English)

    费春东; 马国峰; 王洪运

    2012-01-01

    This paper studies the long-time high air pressure holding performance of butyl chloride rubber by means of airproof performance test of air and helium gas, and gets the data of the two kinds of gas. Data analysis results show butyl chloride rubber can be used as composites vessel' s internal liner for working pressure value between 30MPa and 35MPa. Vessel's air pressure holding data shows the relation of weight-time occurs approximate linear relationship in short-period and nonlinear relationship in long-period. The earlier permeability ratio appears grate wider than later period, with the time increasing, the air permeability appears rapid decreasing trend.%本文通过高压空气及氦气的气保压试验来研究氯化丁基橡胶的长期保压性能,获得了氯化丁基橡胶在高压状态下两种保压介质的气密性能数据.试验数据表明,气瓶在短期保压时间内,保压气体重量与时间近似线性关系.在长期保压时间内,气体的压降与保压时间呈非线性关系,气瓶在保压初期的透气率较大,随保压时间的加长,气瓶的透气率呈快速减小趋势.

  6. Surface Chloride Concentration of Concrete under Shallow Immersion Conditions

    OpenAIRE

    Jun Liu; Kaifeng Tang; Dong Pan; Zongru Lei; Weilun Wang; Feng Xing

    2014-01-01

    Deposition of chloride ions in the surface layer of concrete is investigated in this study. In real concrete structure, chloride ions from the service environment can penetrate into concrete and deposit in the surface layer, to form the boundary condition for further diffusion towards the interior. The deposit amount of chloride ions in the surface layer is normally a function of time, rather than a constant. In the experimental investigation, concrete specimens with different mix proportions...

  7. Multi-Language Programming Environments for High Performance Java Computing

    Directory of Open Access Journals (Sweden)

    Vladimir Getov

    1999-01-01

    Full Text Available Recent developments in processor capabilities, software tools, programming languages and programming paradigms have brought about new approaches to high performance computing. A steadfast component of this dynamic evolution has been the scientific community’s reliance on established scientific packages. As a consequence, programmers of high‐performance applications are reluctant to embrace evolving languages such as Java. This paper describes the Java‐to‐C Interface (JCI tool which provides application programmers wishing to use Java with immediate accessibility to existing scientific packages. The JCI tool also facilitates rapid development and reuse of existing code. These benefits are provided at minimal cost to the programmer. While beneficial to the programmer, the additional advantages of mixed‐language programming in terms of application performance and portability are addressed in detail within the context of this paper. In addition, we discuss how the JCI tool is complementing other ongoing projects such as IBM’s High‐Performance Compiler for Java (HPCJ and IceT’s metacomputing environment.

  8. Methods for evaluating potential sources of chloride in surface waters and groundwaters of the conterminous United States

    Science.gov (United States)

    Granato, Gregory E.; DeSimone, Leslie A.; Barbaro, Jeffrey R.; Jeznach, Lillian C.

    2015-09-04

    Chloride exists as a major ion in most natural waters, but many anthropogenic sources are increasing concentrations of chloride in many receiving waters. Although natural concentrations in continental waters can be as high as 200,000 milligrams per liter, chloride concentrations that are suitable for freshwater ecology, human consumption, and agricultural and industrial water uses commonly are on the order of 10 to 1,000 milligrams per liter. “Road salt” frequently is identified as the sole source of anthropogenic chloride, but only about 30 percent of the salt consumed and released to the environment is used for deicing. Furthermore, several studies in Southern States where the use of deicing salt is minimal also show anthropogenic chloride in rising concentrations and in strong correlation to imperviousness and road density. This is because imperviousness and road density also are strongly correlated to population density. The term “road salt” is a misnomer because deicers applied to parking lots, sidewalks, and driveways can be a substantial source of chloride in some catchments because these land covers are comparable to roadways as a percentage of the total impervious area and commonly receive higher salt application rates than some roadways. Other sources of anthropogenic chloride include wastewater, dust control on unpaved roads, fertilizer, animal waste, irrigation, aquaculture, energy production wastes, and landfill leachates. The assumption that rising chloride concentrations in surface water or groundwater is indicative of contamination by deicing chemicals rather than one or more other potential sources may preclude the identification of toxic, carcinogenic, mutagenic, or endocrine-disrupting contaminants that are associated with many sources of elevated chloride concentrations. Once the sources of anthropogenic chloride in an area of interest have been identified and measured, water and solute budgets can be estimated to guide decisionmakers to

  9. High excitation rovibrational molecular analysis in warm environments

    Science.gov (United States)

    Zhang, Ziwei; Stancil, Phillip C.; Cumbee, Renata; Ferland, Gary J.

    2017-06-01

    Inspired by advances in infrared observation (e.g., Spitzer, Herschel and ALMA), we investigate rovibrational emission CO and SiO in warm astrophysical environments. With recent innovation in collisional rate coefficients and rescaling methods, we are able to construct more comprehensive collisional data with high rovibrational states (vibration up to v=5 and rotation up to J=40) and multiple colliders (H2, H and He). These comprehensive data sets are used in spectral simulations with the radiative transfer codes RADEX and Cloudy. We obtained line ratio diagnostic plots and line spectra for both near- and far-infrared emission lines over a broad range of density and temperature for the case of a uniform medium. Considering the importance of both molecules in probing conditions and activities of UV-irradiated interstellar gas, we model rovibrational emission in photodissociation region (PDR) and AGB star envelopes (such as VY Canis Majoris, IK Tau and IRC +10216) with Cloudy. Rotational diagrams, energy distribution diagrams, and spectra are produced to examine relative state abundances, line emission intensity, and other properties. With these diverse models, we expect to have a better understanding of PDRs and expand our scope in the chemical architecture and evolution of AGB stars and other UV-irradiated regions. The soon to be launched James Webb Space Telescope (JWST) will provide high resolution observations at near- to mid-infrared wavelengths, which opens a new window to study molecular vibrational emission calling for more detailed chemical modeling and comprehensive laboratory astrophysics data on more molecules. This work was partially supported by NASA grants NNX12AF42G and NNX15AI61G. We thank Benhui Yang, Kyle Walker, Robert Forrey, and N. Balakrishnan for collaborating on the collisional data adopted in the current work.

  10. Learning rate and temperament in a high predation risk environment

    Science.gov (United States)

    DePasquale, C.; Wagner, Tyler; Archard, G.A.; Ferguson, B.; Braithwaite, V.A.

    2014-01-01

    Living in challenging environments can influence the behavior of animals in a number of ways. For instance, populations of prey fish that experience frequent, nonlethal interactions with predators have a high proportion of individuals that express greater reaction to risk and increased activity and exploration—collectively known as temperament traits. Temperament traits are often correlated, such that individuals that are risk-prone also tend to be active and explore more. Spatial learning, which requires the integration of many sensory cues, has also been shown to vary in fish exposed to different levels of predation threat. Fish from areas of low predation risk learn to solve spatial tasks faster than fish from high predation areas. However, it is not yet known whether simpler forms of learning, such as learning associations between two events, are similarly influenced. Simple forms of associative learning are likely to be affected by temperament because a willingness to approach and explore novel situations could provide animals with a learning advantage. However, it is possible that routine-forming and inflexible traits associated with risk-prone and increased exploratory behavior may act in the opposite way and make risk-prone individuals poorer at learning associations. To investigate this, we measured temperament in Panamanian bishop fish (Brachyrhaphis episcopi) sampled from a site known to contain many predators. The B. episcopi were then tested with an associative learning task. Within this population, fish that explored more were faster at learning a cue that predicted access to food, indicating a link between temperament and basic learning abilities.

  11. Learning rate and temperament in a high predation risk environment.

    Science.gov (United States)

    DePasquale, C; Wagner, T; Archard, G A; Ferguson, B; Braithwaite, V A

    2014-11-01

    Living in challenging environments can influence the behavior of animals in a number of ways. For instance, populations of prey fish that experience frequent, nonlethal interactions with predators have a high proportion of individuals that express greater reaction to risk and increased activity and exploration-collectively known as temperament traits. Temperament traits are often correlated, such that individuals that are risk-prone also tend to be active and explore more. Spatial learning, which requires the integration of many sensory cues, has also been shown to vary in fish exposed to different levels of predation threat. Fish from areas of low predation risk learn to solve spatial tasks faster than fish from high predation areas. However, it is not yet known whether simpler forms of learning, such as learning associations between two events, are similarly influenced. Simple forms of associative learning are likely to be affected by temperament because a willingness to approach and explore novel situations could provide animals with a learning advantage. However, it is possible that routine-forming and inflexible traits associated with risk-prone and increased exploratory behavior may act in the opposite way and make risk-prone individuals poorer at learning associations. To investigate this, we measured temperament in Panamanian bishop fish (Brachyrhaphis episcopi) sampled from a site known to contain many predators. The B. episcopi were then tested with an associative learning task. Within this population, fish that explored more were faster at learning a cue that predicted access to food, indicating a link between temperament and basic learning abilities.

  12. High bit rate BPSK signals in shallow water environments

    NARCIS (Netherlands)

    Robert, M.K.; Walree, P.A. van

    2003-01-01

    Lately, acoustic data transfer has become an important topic in underwater environments. Several acoustic communication signals e.g. spread spectrum or frequency shift keying signals have been extensively developed. However, in challenging environments, it is still difficult to obtain robust acousti

  13. Stability enhancement of PbSe quantum dots via post-synthetic ammonium chloride treatment for a high-performance infrared photodetector.

    Science.gov (United States)

    Fu, Chunjie; Wang, Haowei; Song, Taojian; Zhang, Li; Li, Weile; He, Bo; sulaman, Muhammad; Yang, Shengyi; Zou, Bingsuo

    2016-02-12

    Infrared (IR) emission lead selenide (PbSe) quantum dots (QDs) have gained considerable attention in the last decade due to their potential applications in optoelectronic devices. However, the comprehensive applications of PbSe QDs have not been realized yet due to their high susceptibility to oxidation in air. In this paper, we demonstrate the stability enhancement of PbSe colloidal QDs via a post-synthetic ammonium chloride treatment and its applications in a solution-processed high-performance IR photodetector with a field-effect transistor (FET) configuration by reversely fabricating the PbSe active layer and polymethylmethacrylate (PMMA) dielectric layer. The responsivity and the specific detectivity of the FET-based photodetector Au(source, drain)/PbSe(52 nm)/PMMA(930 nm)/Au(gate) reached 64.17 mA W(-1) and 5.08 × 10(10) Jones, respectively, under 980 nm laser illumination with an intensity of 0.1 mW cm(-2). Therefore, it provides a promising way to make a high-sensitivity near-IR/mid-IR photodetector.

  14. Stability enhancement of PbSe quantum dots via post-synthetic ammonium chloride treatment for a high-performance infrared photodetector

    Science.gov (United States)

    Fu, Chunjie; Wang, Haowei; Song, Taojian; Zhang, Li; Li, Weile; He, Bo; sulaman, Muhammad; Yang, Shengyi; Zou, Bingsuo

    2016-02-01

    Infrared (IR) emission lead selenide (PbSe) quantum dots (QDs) have gained considerable attention in the last decade due to their potential applications in optoelectronic devices. However, the comprehensive applications of PbSe QDs have not been realized yet due to their high susceptibility to oxidation in air. In this paper, we demonstrate the stability enhancement of PbSe colloidal QDs via a post-synthetic ammonium chloride treatment and its applications in a solution-processed high-performance IR photodetector with a field-effect transistor (FET) configuration by reversely fabricating the PbSe active layer and polymethylmethacrylate (PMMA) dielectric layer. The responsivity and the specific detectivity of the FET-based photodetector Au(source, drain)/PbSe(52 nm)/PMMA(930 nm)/Au(gate) reached 64.17 mA W-1 and 5.08 × 1010 Jones, respectively, under 980 nm laser illumination with an intensity of 0.1 mW cm-2. Therefore, it provides a promising way to make a high-sensitivity near-IR/mid-IR photodetector.

  15. Preparation of pre-reduced pellet using pyrite cinder containing nonferrous metals with high temperature chloridizing- reduction roasting technology-Effect of CaCl2 additive

    Institute of Scientific and Technical Information of China (English)

    陈栋; 朱德庆; 洪澜; 陈瑶; 许继芳; 伍凌

    2015-01-01

    The role of CaCl2 during the high temperature chloridizing-reduction roasting process was investigated, aiming at acquiring high strength blast furnace burden with high iron grade and low nonferrous metals content. The effects of CaCl2 dosage on pelletizing, preheating and reduction were investigated. The results show that CaCl2 can improve the wet drop strength but reduces the thermostability of pyrite cinder green balls. When the dosage of CaCl2 exceeds 1%, the compressive strength of preheated pellets decreases while the growth of iron oxide particles is improved. Furthermore, the compressive strength of pre-reduced pellets increases but the metallization degree of pre-reduced pellets decreases with CaCl2 additive. The removal tests indicate that Zn can be removed completely without CaCl2 additive, Cu is removed only under the condition with CaCl2 additive and part of Pb must be removed by CaCl2 additive.

  16. Chloride Ingress into Concrete under Water Pressure

    OpenAIRE

    Lund, Mia Schou; Sander, Lotte Braad; Grelk, Bent; Hansen, Kurt Kielsgaard

    2011-01-01

    The chloride ingress into concrete under water pressures of 100 kPa and 800 kPa have been investigated by experiments. The specimens were exposed to a 10% NaCl solution and water mixture. For the concrete having w/c = 0.35 the experimental results show the chloride diffusion coefficient at 800 kPa (~8 atm.) is 12 times greater than at 100 kPa (~1 atm.). For w/c = 0.45 and w/c = 0.55 the chloride diffusion coefficients are 7 and 3 times greater. This means that a change in pressure highly infl...

  17. 锂亚硫酰氯电池的高温性能研究%Study on high temperature performance of lithium thionyl chloride battery

    Institute of Scientific and Technical Information of China (English)

    杨中发; 王庆杰; 石斌; 张云朋

    2013-01-01

    研究了高温状态下锂亚硫酰氯(Li/SOCl)电池的开路电压、工作电压平台、倍率放电性能、电压滞后及放电安全性.以相同电流放电,工作温度越高,工作电压平台越高;随着放电电流的增加,工作电压平台降低,放电容量下降;工作温度和电池形变对电池输出容量的影响较大;高温有利于减缓甚至消除电压滞后;电池的最高工作温度不宜超过150℃.%Open circuit voltage,operating voltage platform,rate discharge performance,voltage delay and discharge safety performance of lithium thionyl chloride(Li/SOCl2) battery in high-temperature state were studied.The operating voltage platform rose with the increasing of operating temperature,operating voltage platform decreased and discharge capacity reduced with the increasing of discharge current,operating temperature and deformation would seriously affect output capacity of the battery,high temperature helped to reduce or even eliminate voltage decay,maximum operating temperature of the battery should not exceed 150 ℃.

  18. Leaching of copper concentrates with high arsenic content in chlorine-chloride media; Lixiviacion de concentrados de cobre con alto contenido de arsenico en medio cloro-cloruro

    Energy Technology Data Exchange (ETDEWEB)

    Herreros, O.; Fuentes, G.; Quiroz, R.; Vinals, J.

    2003-07-01

    This work reports the results of copper concentrates leaching which have high arsenic concepts (up to 2.5%). The treatments were carried out using chlorine that forms from sodium hypochlorite and sulphuric acid. The aim of this work is to obtain a solution having high copper content 4 to 6 g/l and 5 to 7 g/l free acid in order to submit it directly to a solvent extraction stage. In addition, this solution should have minimum content of arsenic and chloride ions. To carry out this investigation, an acrylic reactor was constructed where the leaching tests were made at constant temperature in a thermostatic bath under atmospheric pressure. The concentrate samples were obtained from mineral processing plants from Antofagasta, Chile. Typical variables were studied, such as leaching agent concentration, leaching time, pulp density and temperature among others. Some of the residues were analyzed by XRD and EPS. On the other hand, the solutions were analyzed by Atomic Absorption Spectroscopy. The results indicate solutions having the contents stated above can be obtained. (Author) 19 refs.

  19. Plasma simulations of emission line regions in high energy environments

    Science.gov (United States)

    Richardson, Chris T.

    This dissertation focuses on understanding two different, but in each case extreme, astrophysical environments: the Crab Nebula and emission line galaxies. These relatively local objects are well constrained by observations and are test cases of phenomena seen at high-z where detailed observations are rare. The tool used to study these objects is the plasma simulation code known as Cloudy. The introduction provides a brief summary of relevant physical concepts in nebular astrophysics and presents the basic features and assumptions of Cloudy. The first object investigated with Cloudy, the Crab Nebula, is a nearby supernova remnant that previously has been subject to photoionization modeling to reproduce the ionized emission seen in the nebula's filamentary structure. However, there are still several unanswered questions: (1) What excites the H2 emitting gas? (2) How much mass is in the molecular component? (3) How did the H2 form? (4) What is nature of the dust grains? A large suite of observations including long slit optical and NIR spectra over ionized, neutral and molecular gas in addition to HST and NIR ground based images constrain a particularly bright region of H2 emission, Knot 51, which exhibits a high excitation temperature of ˜3000 K. Simulations of K51 revealed that only a trace amount of H2 is needed to reproduce the observed emission and that H2 forms through an uncommon nebular process known as associative detachment. The final chapters of this dissertation focus on interpreting the narrow line region (NLR) in low-z emission line galaxies selected by a novel technique known as mean field independent component analysis (MFICA). A mixture of starlight and radiation from an AGN excites the gas present in galaxies. MFICA separates galaxies over a wide range of ionization into subsets of pure AGN and pure star forming galaxies allowing simulations to reveal the properties responsible for their observed variation in ionization. Emission line ratios can

  20. Flexible sample environment for high resolution neutron imaging at high temperatures in controlled atmosphere

    Energy Technology Data Exchange (ETDEWEB)

    Makowska, Małgorzata G., E-mail: malg@dtu.dk [Department of Energy Conversion and Storage, Technical University of Denmark, Roskilde 4000 (Denmark); European Spallation Source ESS AB, P.O. Box 176, SE-221 00 Lund (Sweden); Theil Kuhn, Luise; Cleemann, Lars N. [Department of Energy Conversion and Storage, Technical University of Denmark, Roskilde 4000 (Denmark); Lauridsen, Erik M. [Xnovo Technology ApS, Galoche Alle 15, Køge 4600 (Denmark); Bilheux, Hassina Z.; Molaison, Jamie J.; Santodonato, Louis J. [Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831 (United States); Tremsin, Anton S. [Space Sciences Laboratory, University of California at Berkeley, Berkeley, California 94720 (United States); Grosse, Mirco [Institute for Applied Material Research, Karlsruhe Institute of Technology, Karlsruhe DE-76021 (Germany); Morgano, Manuel [Paul Scherrer Institut, Villigen PSI CH-5232 (Switzerland); Kabra, Saurabh [ISIS, Rutherford Appleton Laboratory, Chilton OX11 0QX (United Kingdom); Strobl, Markus [European Spallation Source ESS AB, P.O. Box 176, SE-221 00 Lund (Sweden)

    2015-12-15

    High material penetration by neutrons allows for experiments using sophisticated sample environments providing complex conditions. Thus, neutron imaging holds potential for performing in situ nondestructive measurements on large samples or even full technological systems, which are not possible with any other technique. This paper presents a new sample environment for in situ high resolution neutron imaging experiments at temperatures from room temperature up to 1100 °C and/or using controllable flow of reactive atmospheres. The design also offers the possibility to directly combine imaging with diffraction measurements. Design, special features, and specification of the furnace are described. In addition, examples of experiments successfully performed at various neutron facilities with the furnace, as well as examples of possible applications are presented. This covers a broad field of research from fundamental to technological investigations of various types of materials and components.

  1. Developing Polymer Cathode Material for the Chloride Ion Battery.

    Science.gov (United States)

    Zhao, Xiangyu; Zhao, Zhigang; Yang, Meng; Xia, Hui; Yu, Tingting; Shen, Xiaodong

    2017-01-25

    The chloride ion battery is an attractive rechargeable battery owing to its high theoretical energy density and sustainable components. An important challenge for research and development of chloride ion batteries lies in the innovation of the cathode materials. Here we report a nanostructured chloride ion-doped polymer, polypyrrole chloride, as a new type of potential cathode material for the chloride ion battery. The as-prepared polypyrrole chloride@carbon nanotubes (PPyCl@CNTs) cathode shows a high reversible capacity of 118 mAh g(-1) and superior cycling stability. Reversible electrochemical reactions of the PPyCl@CNTs cathode based on the redox reactions of nitrogen species and chloride ion transfer are demonstrated. Our work may guide and offer electrode design principles for accelerating the development of rechargeable batteries with anion transfer.

  2. tRNA separation by high-performance liquid chromatography using an aggregate of ODS-Hypersil and trioctylmethylammonium chloride

    NARCIS (Netherlands)

    Bischoff, Rainer; Graeser, E.; Mclaughlin, L.W.

    1983-01-01

    High-performance liquid chromatography on a reversed-phase support treated with a tetraalkylammonium salt was used to separate tRNAs from baker's yeast. While resolution by this column appears to result from both anion-exchange and reversed-phase chromatography, it is the hydrophobic interactions wh

  3. Cryogenic Impinging Jets Subjected to High Frequency Transverse Acoustic Forcing in a High Pressure Environment

    Science.gov (United States)

    2016-07-27

    other provision of law, no person shall be subject to any penalty for failing to comply with a collection of information if it does not display a ...Transverse Acoustic Forcing in a High Pressure Environment 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) Mario...Briefing Charts 15. SUBJECT TERMS N/ A 16. SECURITY CLASSIFICATION OF: 17. LIMITATION OF ABSTRACT 18. NUMBER OF PAGES 19a. NAME OF RESPONSIBLE

  4. Lithium Sulfuryl Chloride Battery.

    Science.gov (United States)

    Primary batteries , Electrochemistry, Ionic current, Electrolytes, Cathodes(Electrolytic cell), Anodes(Electrolytic cell), Thionyl chloride ...Phosphorus compounds, Electrical conductivity, Calibration, Solutions(Mixtures), Electrical resistance, Performance tests, Solvents, Lithium compounds

  5. Influence of nitrogen on the stress corrosion cracking resistance of austenitic stainless steels in chloride environment; Influence de l'azote sur la resistance a la corrosion sous contrainte d'aciers inoxydables austenitiques en milieu chlorure

    Energy Technology Data Exchange (ETDEWEB)

    Teysseyre, S

    2001-11-01

    The aim of this study is to investigate the influence of nitrogen additions on the Stress Corrosion Cracking (SSC) resistance of austenitic stainless steel in chloride environment. The investigation was carried out in two part: first, an experimental investigation with model industrial steels was carried out and secondly, numerical simulations based on the Corrosion Enhanced Plasticity Model were developed. Both slow strain rate tensile tests and constant load test of the different steels in boiling MgCl{sub 2} (153 deg C) at free potential show that, for a given plastic strain rate, nitrogen addition increases the critical stress for crack initiation without influencing the crack propagation rate. We observed that the creep rate under constant load was affected by the nitrogen content. As a consequence, the SCC behaviour (cracks density and propagation rate) depends on the nitrogen content. We thus confirm that the nitrogen content influences the corrosion - deformation interaction mechanisms via its positive contribution to the flow stress. These experimental results are reproduced semi-quantitatively by means of numerical simulations at the scale of crack. - dislocation interactions. The presence of nitrogen is modelled by an increased lattice friction stress, which in turn affects the dynamics of crack tip shielding by dislocation pile-ups. We conclude that nitrogen addition in austenitic stainless steels increases the SC crack initiation stress in proportion of the increased flow stress, without penalty in terms of SC crack propagation rate. (author)

  6. EXPERIMENTAL STUDY ON THE PENETRATION OF CHLORIDE IONS INTO HIGH PERFORMANCE CONCRETE%高性能混凝土氯离子渗透性能的试验研究

    Institute of Scientific and Technical Information of China (English)

    盛黎; 姚谏

    2011-01-01

    Using the ASTM C1202 method and the NEL method,the experimental study on the impermeability to chloride ions of high performance concrete was performed,including high performance concrete mixed with only slag and mixed with compound mineral admixture.The correlations between electric flux and chloride diffusion coefficient were discussed.Test result indicated that the mineral admixture can effectively raise the ability to resist chloride ion penetration into high performance concrete.Mixing slag and fly ash especially could more effectively improve the impermebibty to chloride ions of the high performance concrete,and good correlation between electric flux and chloride diffusion coefficient was also showed.When water cement ratio was smaller,the correlation between the two indexes was better.%采用ASTM C1202法及NEL法,对单掺矿渣和复掺粉煤灰、矿渣的高性能混凝土进行抗氯离子渗透性能的试验研究,并探讨电通量与氯离子扩散系数之间的相关性。结果表明:矿物掺合料能有效地改善高性能混凝土的抗氯离子渗透性能,复掺粉煤灰和矿渣比单掺矿渣的效果更佳;电通量与氯离子扩散系数之间具有较好的相关性,当水胶比较小时,两指标间的相关性更好。

  7. High performance computing network for cloud environment using simulators

    CERN Document Server

    Singh, N Ajith

    2012-01-01

    Cloud computing is the next generation computing. Adopting the cloud computing is like signing up new form of a website. The GUI which controls the cloud computing make is directly control the hardware resource and your application. The difficulty part in cloud computing is to deploy in real environment. Its' difficult to know the exact cost and it's requirement until and unless we buy the service not only that whether it will support the existing application which is available on traditional data center or had to design a new application for the cloud computing environment. The security issue, latency, fault tolerance are some parameter which we need to keen care before deploying, all this we only know after deploying but by using simulation we can do the experiment before deploying it to real environment. By simulation we can understand the real environment of cloud computing and then after it successful result we can start deploying your application in cloud computing environment. By using the simulator it...

  8. Application of activated charcoal radon collectors in high humidity environments

    Energy Technology Data Exchange (ETDEWEB)

    Iimoto, Takeshi E-mail: iimoto@rcnst.u-tokyo.ac.jp; Tokonami, Shinji; Morishita, Yasuaki; Kosako, Toshiso

    2004-09-01

    Most commercially based activated charcoal radon collectors were designed for use in indoor environments. However, at present, they are often used for research in radon surveys in unique environments, such as in the bathrooms, underground areas, mines, caves and tunnels. In these environments, the relative humidity would be around 100%, and a change in the sensitivity of cpm(Bq m{sup -3}){sup -1}(radon) would occur. For this study, the reduction in the sensitivity of activated charcoal radon collector due to environmental humidity was investigated, and the data correction was discussed. Here, ST-100 (Pico-Rad) was selected as an example of a familiar activated charcoal radon collector. According to our performance test, the humidity of 90% (20 deg. C) resulted in a 15% reduction of the sensitivity for 24 h collection. The ST-100 user should discuss the necessity of data correction by comparing the change of sensitivity with other levels of estimation errors.

  9. Application of activated charcoal radon collectors in high humidity environments.

    Science.gov (United States)

    Iimoto, Takeshi; Tokonami, Shinji; Morishita, Yasuaki; Kosako, Toshiso

    2005-01-01

    Most commercially based activated charcoal radon collectors were designed for use in indoor environments. However, at present, they are often used for research in radon surveys in unique environments, such as in the bathrooms, underground areas, mines, caves and tunnels. In these environments, the relative humidity would be around 100%, and a change in the sensitivity of cpm(Bq m(-3))(-1)(radon) would occur. For this study, the reduction in the sensitivity of activated charcoal radon collector due to environmental humidity was investigated, and the data correction was discussed. Here, ST-100 (Pico-Rad) was selected as an example of a familiar activated charcoal radon collector. According to our performance test, the humidity of 90% (20 degrees C) resulted in a 15% reduction of the sensitivity for 24 h collection. The ST-100 user should discuss the necessity of data correction by comparing the change of sensitivity with other levels of estimation errors.

  10. Packaged triboelectric nanogenerator with high endurability for severe environments

    Science.gov (United States)

    Gu, Long; Cui, Nuanyang; Liu, Jinmei; Zheng, Youbin; Bai, Suo; Qin, Yong

    2015-10-01

    Many factors in the environment (such as dust, moisture and rain) severely influence the output performance of a triboelectric nanogenerator (TNG), which greatly limits its application. In this work, we designed and fabricated a kind of packaged TNG (PTNG) that can work normally in dust and humidity for harvesting noise energy. Under a sound wave of 110 dB and 200 Hz, the PTNG can generate a maximum output voltage of 72 V and a maximum output current of 0.66 mA. In the structure of the PTNG, the frictional layers are fully isolated from the ambient environment, which makes it work steadily in dusty and humid conditions without any damping of the output performance. Moreover, it can be used as a stable power source to directly light up 24 red commercial light emitting diodes (LEDs) driven by sound even in a severely rainy environment. This PTNG has great potential to be applied in real environments, which is critically important to the application of TNGs.Many factors in the environment (such as dust, moisture and rain) severely influence the output performance of a triboelectric nanogenerator (TNG), which greatly limits its application. In this work, we designed and fabricated a kind of packaged TNG (PTNG) that can work normally in dust and humidity for harvesting noise energy. Under a sound wave of 110 dB and 200 Hz, the PTNG can generate a maximum output voltage of 72 V and a maximum output current of 0.66 mA. In the structure of the PTNG, the frictional layers are fully isolated from the ambient environment, which makes it work steadily in dusty and humid conditions without any damping of the output performance. Moreover, it can be used as a stable power source to directly light up 24 red commercial light emitting diodes (LEDs) driven by sound even in a severely rainy environment. This PTNG has great potential to be applied in real environments, which is critically important to the application of TNGs. Electronic supplementary information (ESI) available. See

  11. Sensors for Highly Toxic Gases: Methylamine and Hydrogen Chloride Detection at Low Concentrations in an Ionic Liquid on Pt Screen Printed Electrodes

    Science.gov (United States)

    Murugappan, Krishnan; Silvester, Debbie S.

    2015-01-01

    Commercially available Pt screen printed electrodes (SPEs) have been employed as possible electrode materials for methylamine (MA) and hydrogen chloride (HCl) gas detection. The room temperature ionic liquid (RTIL) 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([C2mim][NTf2]) was used as a solvent and the electrochemical behaviour of both gases was first examined using cyclic voltammetry. The reaction mechanism appears to be the same on Pt SPEs as on Pt microelectrodes. Furthermore, the analytical utility was studied to understand the behaviour of these highly toxic gases at low concentrations on SPEs, with calibration graphs obtained from 10 to 80 ppm. Three different electrochemical techniques were employed: linear sweep voltammetry (LSV), differential pulse voltammetry (DPV) and square wave voltammetry (SWV), with no significant differences in the limits of detection (LODs) between the techniques (LODs were between 1.4 to 3.6 ppm for all three techniques for both gases). The LODs achieved on Pt SPEs were lower than the current Occupational Safety and Health Administration Permissible Exposure Limit (OSHA PEL) limits of the two gases (5 ppm for HCl and 10 ppm for MA), suggesting that Pt SPEs can successfully be combined with RTILs to be used as cheap alternatives for amperometric gas sensing in applications where these toxic gases may be released. PMID:26506358

  12. Sensors for Highly Toxic Gases: Methylamine and Hydrogen Chloride Detection at Low Concentrations in an Ionic Liquid on Pt Screen Printed Electrodes

    Directory of Open Access Journals (Sweden)

    Krishnan Murugappan

    2015-10-01

    Full Text Available Commercially available Pt screen printed electrodes (SPEs have been employed as possible electrode materials for methylamine (MA and hydrogen chloride (HCl gas detection. The room temperature ionic liquid (RTIL 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonylimide ([C2mim][NTf2] was used as a solvent and the electrochemical behaviour of both gases was first examined using cyclic voltammetry. The reaction mechanism appears to be the same on Pt SPEs as on Pt microelectrodes. Furthermore, the analytical utility was studied to understand the behaviour of these highly toxic gases at low concentrations on SPEs, with calibration graphs obtained from 10 to 80 ppm. Three different electrochemical techniques were employed: linear sweep voltammetry (LSV, differential pulse voltammetry (DPV and square wave voltammetry (SWV, with no significant differences in the limits of detection (LODs between the techniques (LODs were between 1.4 to 3.6 ppm for all three techniques for both gases. The LODs achieved on Pt SPEs were lower than the current Occupational Safety and Health Administration Permissible Exposure Limit (OSHA PEL limits of the two gases (5 ppm for HCl and 10 ppm for MA, suggesting that Pt SPEs can successfully be combined with RTILs to be used as cheap alternatives for amperometric gas sensing in applications where these toxic gases may be released.

  13. High photocatalytic degradation activity of the polyvinyl chloride (PVC)-vitamin C (VC)-TiO2 nano-composite film.

    Science.gov (United States)

    Yang, Changjun; Gong, Chuqing; Peng, Tianyou; Deng, Kejian; Zan, Ling

    2010-06-15

    A novel photodegradable polyvinyl chloride (PVC)-vitamin C (VC)-TiO(2) nano-composite film was prepared by embedding VC modified nano-TiO(2) photocatalyst into the commercial PVC plastic. The solid-phase photocatalytic degradation behavior of PVC-VC-TiO(2) nano-composite film under UV light irradiation was investigated and compared with those of the PVC-TiO(2) film and the pure PVC film, with the aid of UV-Vis spectroscopy, scanning electron microscopy (SEM), weight loss monitoring, and X-ray diffraction spectra (XRD). The results show that PVC-VC-TiO(2) nano-composite film has a high photocatalytic activity; the photocatalytic degradation rate of it is two times higher than that of PVC-TiO(2) film and fifteen times higher than that of pure PVC film. The optimal mass ratio of VC to TiO(2) is found to be 0.5. The mechanism of enhancing photocatalytic activity is attributed to the formation of a Ti(IV)-VC charge-transfer complex with five-member chelate ring structure and a rapid photogenerated charge separation is thus achieved.

  14. CMOS pixel sensors on high resistive substrate for high-rate, high-radiation environments

    Science.gov (United States)

    Hirono, Toko; Barbero, Marlon; Breugnon, Patrick; Godiot, Stephanie; Gonella, Laura; Hemperek, Tomasz; Hügging, Fabian; Krüger, Hans; Liu, Jian; Pangaud, Patrick; Peric, Ivan; Pohl, David-Leon; Rozanov, Alexandre; Rymaszewski, Piotr; Wang, Anqing; Wermes, Norbert

    2016-09-01

    A depleted CMOS active pixel sensor (DMAPS) has been developed on a substrate with high resistivity in a high voltage process. High radiation tolerance and high time resolution can be expected because of the charge collection by drift. A prototype of DMAPS was fabricated in a 150 nm process by LFoundry. Two variants of the pixel layout were tested, and the measured depletion depths of the variants are 166 μm and 80 μm. We report the results obtained with the prototype fabricated in this technology.

  15. CMOS pixel sensors on high resistive substrate for high-rate, high-radiation environments

    Energy Technology Data Exchange (ETDEWEB)

    Hirono, Toko, E-mail: thirono@uni-bonn.de [Physikalisches Institute der Universität Bonn, Bonn (Germany); Barbero, Marlon; Breugnon, Patrick; Godiot, Stephanie [CPPM, Aix-Marseille Universite, CNRS/IN2P3, Marseille (France); Gonella, Laura; Hemperek, Tomasz; Hügging, Fabian; Krüger, Hans [Physikalisches Institute der Universität Bonn, Bonn (Germany); Liu, Jian; Pangaud, Patrick [CPPM, Aix-Marseille Universite, CNRS/IN2P3, Marseille (France); Peric, Ivan [IPE, Karlsruher Institut für Technologie, Karlsruhe (Germany); Pohl, David-Leon [Physikalisches Institute der Universität Bonn, Bonn (Germany); Rozanov, Alexandre [CPPM, Aix-Marseille Universite, CNRS/IN2P3, Marseille (France); Rymaszewski, Piotr [Physikalisches Institute der Universität Bonn, Bonn (Germany); Wang, Anqing [CPPM, Aix-Marseille Universite, CNRS/IN2P3, Marseille (France); Wermes, Norbert [Physikalisches Institute der Universität Bonn, Bonn (Germany)

    2016-09-21

    A depleted CMOS active pixel sensor (DMAPS) has been developed on a substrate with high resistivity in a high voltage process. High radiation tolerance and high time resolution can be expected because of the charge collection by drift. A prototype of DMAPS was fabricated in a 150 nm process by LFoundry. Two variants of the pixel layout were tested, and the measured depletion depths of the variants are 166 μm and 80 μm. We report the results obtained with the prototype fabricated in this technology.

  16. Is Learning in Low Immersive Environments Carried over to High Immersive Environments?

    Directory of Open Access Journals (Sweden)

    Dror David Lev

    2012-01-01

    Full Text Available One of the more debated issues regarding training simulators is their validity for transfer of skills to sensory environments that differ from the simulator. In two experiments, the advantages of three-dimensional (3D and collocated (Col visual displays were evaluated in a realistic and complex visuomotor task. The two factors were evaluated independently, comparing Col-2D with dislocated-2D (experiment 1 and with Col-3D (experiment 2. As expected, in both cases the more immersive presentation condition facilitated better performance. Furthermore, improvement following training in the more immersive condition carried over to the following less immersive condition but there was no carry over in the opposing order of presentation. This is taken as an indication for the differential development of skills conditioned by the level of immersiveness of the training environment. This further suggests that learning of complex realistic tasks is not carried over from less immersive simulator to the complex sensory environment of reality, due to the large gap in sensory patterns.

  17. TH-C-19A-12: Two-Dimensional High Spatial-Resolution Dosimeter Using Europium Doped Potassium Chloride

    Energy Technology Data Exchange (ETDEWEB)

    Li, H; Yang, D; Xiao, Z [Washington University School of Medicine, St. Louis, MO (United States); Driewer, J [University of Nebraska Medical Center, Omaha, NE (United States); Han, Z [Brigham and Womens Hospital and Harvard Medical School, Boston, MA (United States); Low, D [UCLA, Los Angeles, CA (United States)

    2014-06-15

    Purpose: Recent research has shown that KCl:Eu2+ has great potential for use in megavoltage radiation therapy dosimetry because this material exhibits excellent storage performance and is reusable due to strong radiation hardness. This work reports our attempts to fabricate 2D KCl:Eu2+ storage phosphor films (SPFs) using both a physical vapor deposition (PVD) method and a tape casting method. Methods: A thin layer of KCl:Eu2+ was deposited on a substrate of borosilicate glass (e.g., laboratory slides) with a PVD system. For tape casting, a homogenous suspension containing storage phosphor particles, liquid vehicle and polymer binder was formed and subsequently cast by doctor-blade onto a polyethylene terephthalate substrate to form a 150 μm thick SPF. Results: X ray diffraction analysis showed that a 10 μm thick PVD sample was composed of highly crystalline KCl. No additional phases were observed, suggesting that the europium activator had completed been incorporated into the KCl matrix. Photostimulated luminescence and photoluminescence spectra suggested that F (Cl−) centers were the electron storage centers post x ray irradiation and that Eu2+ cations acted as luminescence centers in the photostimulation process. The 150 μm thick casted KCl:Eu2+ SPF showed sub-millimeter spatial resolution. Monte Carlo simulations further demonstrated that the admixture of 20% KCl:Eu2+ and 80% low Z polymer binder exhibited almost no energy dependence in a 6 MV beam. KCl:Eu2+ pellet samples showed a large dynamic range from 0.01 cGy to 60 Gy dose-to-water, and saturated at approximately 500 Gy as a Result of its intrinsic high radiation hardness. Conclusions: This discovery research provides strong evidence that KCl:Eu2+ based SPF with associated readout apparatus could Result in a novel electronic film system that has all the desirable features associated with classic radiographic film and, importantly, water equivalence and the capability of permanent identification of

  18. The NDT methods under high temperature service environment

    Directory of Open Access Journals (Sweden)

    Zhang Zhen-guo

    2016-01-01

    Full Text Available Concerning the detective requirement of the equipment under high temperature running status, this paper summarizes the technical characteristics and related applications of several non-destructive testing methods(NDT, such as thermal infrared imaging technology in high temperature, ultrasonic testing technique in high temperature, pulsed eddy current technology in high temperature and magnetic powder flaw detection technology in high temperature, penetration testing technique in high temperature and indirect visual detection in high temperature and on-line monitoring system in high temperature.

  19. Congenital Chloride Diarrhea: Diagnosis by Easy-Accessible Chloride Measurement in Feces

    Directory of Open Access Journals (Sweden)

    C. Gils

    2016-01-01

    Full Text Available Background. Congenital chloride diarrhea (CCD is an autosomal recessive disorder caused by mutations in the genes encoding the intestinal Cl−/HCO3- exchanger and is clinically characterized by watery, profound diarrhea, electrolyte disturbances, and metabolic alkalosis. The CCD diagnosis is based on the clinical symptoms and measurement of high chloride concentration in feces (>90 mmol/L and is confirmed by DNA testing. Untreated CCD is lethal, while long-term clinical outcome improves when treated correctly. Case Presentation. A 27-year-old woman had an emergency caesarian due to pain and discomfort in gestational week 36 + 4. The newborn boy had abdominal distension and yellow fluid per rectum. Therapy with intravenous glucose and sodium chloride decreased his stool frequency and improved his clinical condition. A suspicion of congenital chloride diarrhea was strongly supported using blood gas analyzer to measure an increased chloride concentration in the feces; the diagnosis was confirmed by DNA testing. Discussion. Measurement of chloride in feces using an ordinary blood gas analyzer can serve as a preliminary analysis when congenital chloride diarrhea is suspected. This measurement can be easily performed with a watery feces composition. An easy-accessible chloride measurement available will facilitate the diagnostics and support the initial treatment if CCD is suspected.

  20. Chloride Ingress into Concrete under Water Pressure

    DEFF Research Database (Denmark)

    Lund, Mia Schou; Sander, Lotte Braad; Grelk, Bent

    2011-01-01

    Pa (~8 atm.) is 12 times greater than at 100 kPa (~1 atm.). For w/c = 0.45 and w/c = 0.55 the chloride diffusion coefficients are 7 and 3 times greater. This means that a change in pressure highly influences the chloride ingress into the concrete and thereby the life length models for concrete structures.......The chloride ingress into concrete under water pressures of 100 kPa and 800 kPa have been investigated by experiments. The specimens were exposed to a 10% NaCl solution and water mixture. For the concrete having w/c = 0.35 the experimental results show the chloride diffusion coefficient at 800 k...

  1. Development and validation of a rapid ultra-high performance liquid chromatography method for the assay of benzalkonium chloride using a quality-by-design approach.

    Science.gov (United States)

    Mallik, Rangan; Raman, Srividya; Liang, Xiaoli; Grobin, Adam W; Choudhury, Dilip

    2015-09-25

    A rapid robust reversed-phase UHPLC method has been developed for the analysis of total benzalkonium chloride in preserved drug formulation. A systematic Quality-by-Design (QbD) method development approach using commercial, off the shelf software (Fusion AE(®)) has been used to optimize the column, mobile phases, gradient time, and other HPLC conditions. Total benzalkonium chloride analysis involves simple sample preparation. The method uses gradient elution from an ACE Excel 2 C18-AR column (50mm×2.1mm, 2.0μm particle size), ammonium phosphate buffer (pH 3.3; 10mM) as aqueous mobile phase and methanol/acetonitrile (85/15, v/v) as the organic mobile phase with UV detection at 214nm. Using these conditions, major homologs of the benzalkonium chloride (C12 and C14) have been separated in less than 2.0min. The validation results confirmed that the method is precise, accurate and linear at concentrations ranging from 0.025mg/mL to 0.075mg/mL for total benzalkonium chloride. The recoveries ranged from 99% to 103% at concentrations from 0.025mg/mL to 0.075mg/mL for total benzalkonium chloride. The validation results also confirmed the robustness of the method as predicted by Fusion AE(®).

  2. Performance of High Strength POFA Concrete in Acidic Environment

    Directory of Open Access Journals (Sweden)

    Mohamed Ismail

    2010-03-01

    disposing palm oil fuel ash, a by-product of palm oil mill since many years ago. The discovery made by researchers of Universiti Teknologi Malaysia last century in revealing the potential of this finely ground waste as a partial cement replacement in normal concrete has stem efforts towards studying the possibility of using it in high strength concrete production. This paper illustrates the durability aspect of high strength concrete produced using POFA of different fineness when exposed to acidic environment. Two POFA concrete mixes with different fineness termed (POFA 45 and POFA 10 at 20% replacement level by weight of cement and an OPC concrete mix functioning as control specimen termed Po was considered in this study. All the specimens were subjected to water curing for 28 days before immersed in the hydrochloric solution having pH 2 for 1800 hours. The progressive deterioration was evaluated through mass changing of the specimens, visual inspection and relative compressive strength determinations. Conclusively, the study found that increase in the POFA fineness enhances the resistance of high strength POFA concrete towards acid attack.

  3. Photo-Fenton oxidation of phenol and organochlorides (2,4-DCP and 2,4-D) in aqueous alkaline medium with high chloride concentration.

    Science.gov (United States)

    Luna, Airton J; Chiavone-Filho, Osvaldo; Machulek, Amilcar; de Moraes, José Ermírio F; Nascimento, Cláudio A O

    2012-11-30

    A highly concentrated aqueous saline-containing solution of phenol, 2,4-dichlorophenoxyacetic acid (2,4-D) and 2,4-dichlorophenol (2,4-DCP) was treated by the photo-Fenton process in a system composed of an annular reactor with a quartz immersion well and a medium-pressure mercury lamp (450 W). The study was conducted under special conditions to minimize the costs of acidification and neutralization, which are usual steps in this type of process. Photochemical reactions were carried out to investigate the influence of some process variables such as the initial concentration of Fe(2+) ([Fe(2+)](0)) from 1.0 up to 2.5 mM, the rate in mmol of H(2)O(2) fed into the system (FH(2)O(2);in) from 3.67 up to 7.33 mmol of H(2)O(2)/min during 120 min of reaction time, and the initial pH (pH(0)) from 3.0 up to 9.0 in the presence and absence of NaCl (60.0 g/L). Although the optimum pH for the photo-Fenton process is about 3.0, this particular system performed well in experimental conditions starting at alkaline and neutral pH. The results obtained here are promising for industrial applications, particularly in view of the high concentration of chloride, a known hydroxyl radical scavenger and the main oxidant present in photo-Fenton processes.

  4. 40 CFR 415.240 - Applicability; description of the ammonium chloride production subcategory.

    Science.gov (United States)

    2010-07-01

    ... ammonium chloride production subcategory. 415.240 Section 415.240 Protection of Environment ENVIRONMENTAL... SOURCE CATEGORY Ammonium Chloride Production Subcategory § 415.240 Applicability; description of the ammonium chloride production subcategory. The provisions of this subpart are applicable to...

  5. Effects of recharge and discharge on delta2H and delta18O composition and chloride concentration of high arsenic/fluoride groundwater from the Datong Basin, northern China.

    Science.gov (United States)

    Xie, Xianjun; Wang, Yanxin; Su, Chunli; Duan, Mengyu

    2013-02-01

    To better understand the effects of recharge and discharge on the hydrogeochemistry of high levels of arsenic (As) and fluoride (F) in groundwater, environmental isotopic composition (delta2H and delta18O) and chloride (Cl) concentrations were analyzed in 29 groundwater samples collected from the Datong Basin. High arsenic groundwater samples (As > 50 micog/L) were found to be enriched in lighter isotopic composition that ranged from -92 to -78 per thousand for deuterium (delta2H) and from -12.5 to -9.9 per thousand for oxygen-18 (delta18O). High F-containing groundwater (F > 1 mg/L) was relatively enriched in heavier isotopic composition and varied from -90 to -57 per thousand and from -12.2 to -6.7 per thousand for delta2H and delta18O, respectively. High chloride concentrations and delta18O values were primarily measured in groundwater samples from the northern and southwestern portions of the study area, indicating the effect of evaporation on groundwater. The observation of relatively homogenized and low delta18O values and chloride concentrations in groundwater samples from central part of the Datong Basin might be a result of fast recharge by irrigation returns, which suggests that irrigation using arsenic-contaminated groundwater affected the occurrence of high arsenic-containing groundwater in the basin.

  6. The effects of surface treatments on rapid chloride permeability tests

    KAUST Repository

    Yoon, Seyoon

    2012-08-01

    Surface treatments are commonly applied to improve the chloride resistance of concrete structures exposed to saline environments. Information on chloride ingress to surface-treated concrete is mostly provided by application of the rapid chloride permeability test (RCPT); this test is short in duration and provides rapid results. This study presents a numerical formulation, based on the extended Nernst-Plank/Poisson (NPP) equation, to model the effect of the surface treatment on a sample tested by RCPT. Predictions of the model are compared to experimental measurements. The simulations show that the results from RCPT, in terms of ionic profiles and measurement of the electric field, are dependent on the effectiveness of surface treatments. During RCPT, highly effective surface treatments cause both cations and anions to flocculate at the interface between the surface treatment and the concrete, creating a local electric field. Our numerical model includes these phenomena and presents a methodology to obtain more accurate diffusivities of the surface-treated- concrete from RCPT. © 2012 Elsevier B.V. All rights reserved.

  7. 烧伤回吸期持续性高钠高氯与侵袭性感染%Persistent High Level of Sodium and Chloride Ions and Invasive Infection in Resorption Phase Postburn

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    目的:探讨大面积烧伤患者持续性高钠高氯产生的原因及防治措施;动态监测大面积烧伤后血清Na+,Cl-的临床意义。方法:回顾性分析了7例严重烧伤后持续性高Na+高Cl-和61例严重烧伤后非持续性高Na+,高Cl-患者的临床特点。结果:7例严重烧伤后持续高Na+,高Cl-患者均有严重侵袭性感染;且高Na+出现愈早,上升愈快,则感染愈重,愈后愈差。结论:1.烧伤后持续性高Na+,高Cl-产生的原因是严重侵袭性感染。2.动态监测血清Na+Cl-对感染的评价及抗感染效果有积极意义。3.预防措施包括平稳渡过休克,保护创面,避免长途转运。治疗上一旦出现持续性高钠高氯,除对症治疗外,根本措施是创面处理及抗感染。%Objective: To investigate the cause persistent high level of sodium and chloride ions in serum and methods for its prevention and treatment. The clinical significance of dynamic monitoring of serum sodium and chloride ion levels in severe burn patients. Method: To make a review of 7 cases with persistent high serum sodium and chloride ion levels and 61 cases without. Results: All of the severe cases had invasive infection. The earlier the presence of high serum sodium and chloride ion levels, the more dangerous the case. Conclusion: 1. Persistent high serum sodium and chloride ion levels is caused by invasive infection. 2. Dynamic monitoring of serum sodium and chloride ion levels is of great clinical significance. 3. Prevention measures include: to tide over shock stage, to protect burn wounds, to avoid long distance transfer. 4. Treating measures include careful management of burn wounds, anti-infection and expectant treatment.

  8. High-Speed Mobile Communications in Hostile Environments

    CERN Document Server

    AUTHOR|(SzGeCERN)739920; Sierra, Rodrigo; Chapron, Frederic; CERN. Geneva. IT Department

    2015-01-01

    With the inexorable increase in the use of mobile devices, wireless connectivity is expected by users anywhere, anytime. In general, this requirement is addressed in office buildings or public locations through the use of Wi-Fi technology but Wi-Fi is not well adapted for use in large experiment halls and complex underground environments, especially those where radiation exposure is an issue, such as the LHC tunnel and experimental caverns. 4G/LTE technology, however, looks to be well adapted to addressing mobility needs in such areas. We report here the studies CERN has undertaken on the use of 4G/LTE in the LHC tunnel, presenting results on the data throughput that can be achieved and discussing issues such as the provision of a consistent user experience.

  9. Nuclear neutrino energy spectra in high temperature astrophysical environments

    Science.gov (United States)

    Misch, G. Wendell; Fuller, George M.

    2016-11-01

    Astrophysical environments that reach temperatures greater than ˜100 keV can have significant neutrino energy loss via both plasma processes and nuclear weak interactions. We find that nuclear processes likely produce the highest-energy neutrinos. The important weak nuclear interactions include both charged current channels (electron capture and emission and positron capture and emission) and neutral current channels (deexcitation of nuclei via neutrino pair emission). We show that, in order to make a realistic prediction of the nuclear neutrino spectrum, one must take nuclear structure into account; in some cases, the most important transitions may involve excited states, possibly in both parent and daughter nuclei. We find that the standard technique of producing a neutrino energy spectrum by using a single transition with a Q value and matrix element chosen to fit published neutrino production rates and energy losses will not accurately capture important spectral features.

  10. Nuclear neutrino energy spectra in high temperature astrophysical environments

    CERN Document Server

    Misch, G Wendell

    2016-01-01

    Astrophysical environments that reach temperatures greater than $\\sim$ 100 keV can have significant neutrino energy loss via both plasma processes and nuclear weak interactions. We find that nuclear processes likely produce the highest-energy neutrinos. Among the important weak nuclear interactions are both charged current channels (electron capture/emission and positron capture/emission) and neutral current channels (de-excitation of nuclei via neutrino pair emission). We show that in order to make a realistic prediction of the nuclear neutrino spectrum, one must take nuclear structure into account; in some cases, the most important transitions may involve excited states, possibly in both parent and daughter nuclei. We find that the standard technique of producing a neutrino energy spectrum by using a single transition with a Q-value and matrix element chosen to fit published neutrino production rates and energy losses will not accurately capture important spectral features.

  11. High-Speed Mobile Communications in Hostile Environments

    Science.gov (United States)

    Agosta, S.; Sierra, R.; Chapron, F.

    2015-12-01

    With the inexorable increase in the use of mobile devices, wireless connectivity is expected by users anywhere, anytime. In general, this requirement is addressed in office buildings or public locations through the use of Wi-Fi technology but Wi-Fi is not well adapted for use in large experiment halls and complex underground environments, especially those where radiation exposure is an issue, such as the LHC tunnel and experimental caverns. 4G/LTE technology, however, looks to be well adapted to addressing mobility needs in such areas. We report here the studies CERN has undertaken on the use of 4G/LTE in the LHC tunnel, presenting results on the data throughput that can be achieved and discussing issues such as the provision of a consistent user experience.

  12. Surface Chloride Concentration of Concrete under Shallow Immersion Conditions

    Directory of Open Access Journals (Sweden)

    Jun Liu

    2014-09-01

    Full Text Available Deposition of chloride ions in the surface layer of concrete is investigated in this study. In real concrete structure, chloride ions from the service environment can penetrate into concrete and deposit in the surface layer, to form the boundary condition for further diffusion towards the interior. The deposit amount of chloride ions in the surface layer is normally a function of time, rather than a constant. In the experimental investigation, concrete specimens with different mix proportions are immersed in NaCl solution with a mass concentration of 5%, to simulate the shallow immersion condition in sea water, and the surface chloride concentrations are measured at different ages. It is found that the surface chloride concentration increases following the increasing immersion durations, and varies from a weight percentage of 0.161%–0.781% in concretes with different mix proportions. The w/c (water-to-cement ratio influences the surface chloride concentration significantly, and the higher the w/c is, the higher the surface chloride concentration will be, at the same age. However, following the prolonging of immersion duration, the difference in surface chloride concentration induced by w/c becomes smaller and smaller. The incorporation of fly ash leads to higher surface chloride concentration. The phenomena are explained based on pore structure analyses.

  13. Study on Preparation Conditions of High-purity Magnesium Chloride%铵解水镁石工艺条件研究

    Institute of Scientific and Technical Information of China (English)

    赵丹丹; 沙聪聪; 韩春玉; 罗根祥; 刘春生

    2013-01-01

      确定了氯化铵是溶解水镁石较为合适的铵盐,考察了水镁石与氯化铵物质的量配比、反应温度以及反应时间等因素对水镁石溶解的影响.结果表明,在水镁石与氯化铵物质的量配比为1∶22、反应温度为100℃、反应时间为2 h的条件下,水镁石在氯化铵溶液中的溶解度最大,溶液中镁离子浓度达到了2.46%.%It’s identified that appropriate ammonium salt to dissolve the brucite was ammonium chloride. The effect of different factors on dissolving the brucite was investigated, such as ratio of ammonium chloride and brucite, reaction temperature and reaction time. The results show that:when the ratio of ammonium chloride and brucite is 1∶22, the reaction temperature is 100 ℃, the reaction time is 2 h, the solubility of the brucite in the ammonium chloride can reach the maximum, the ion concentration of magnesium is 2.46%.

  14. ENVIRONMENTAL EXPOSURE TO VINYL CHLORIDE

    Directory of Open Access Journals (Sweden)

    Henryka Langauer-Lewowicka

    2010-09-01

    Full Text Available Vinyl chloride (VC monomer is a wellknown carcinogenic and mutagenic substance causes liver damages, angiosarcoma of the liver, acro – osteolysis, sclerodermalike changes in workers chronically exposed to this gas. There are following VC emitors to the environment: VC production plants, polymerization facilities and planes where polyvinyl products are fabricated. Because of that, the general population is coming into VC contact through polluted air, food and water. VC concentration in all mentioned sites is very low, often not detectable. There was found any health risk for the general population. The VC air concentration in the vicinity to antropogenic emitors is always higher. Such a situation may causes undesirable health effect for residents living in the neighbourhood. Epidemiological studies are performed to detect the adverse VC effect in selected cohorts. Non of the study did not confirmed cases of angiosarcoma among residents living near a vinyl chloride sites. VC production is growing permanently, so VC emission will be higher. Because of that health monitoring of general population and especially of selected groups seems to be necessary in the future.

  15. Beam test results of CMS RPCs at high eta region under high-radiation environment

    CERN Document Server

    Park, S; Bahk, S Y; Hong, B; Hong, S J; Kang, D H; Kang, T I; Kim, T J; Kim, Y J; Kim, Y U; Koo, D G; Lee, H W; Lee, K S; Lee, S J; Lim, J K; Moon, D H; Nam, S K; Oh, J K; Park, W J; Rhee, J T; Ryu, M S; Shim, H H; Sim, K S

    2004-01-01

    The Compact Muon Solenoid (CMS) forward resistivity plate chambers (RPCs) at the high eta region must be operated in presence of a radiation-induced rate as high as 1 kHz/cm**2. It is still unknown if the RPCs coated with linseed oil can be operated under such a high- radiation environment over the lifetime of CMS. Non-oiled RPCs may be one of the options since phenolic or melamine-coated bakelite is chemically stabler than linseed oil. We have constructed oiled and non-oiled RPCs at the high eta region of CMS using phenolic bakelite and tested them in the Gamma Irradiation Facility at CERN. While both RPCs show the same characteristics in the efficiency and the strip multiplicity, the non-oiled RPC generates an intrinsic noise rate of 50 Hz/cm**2, compared to only 5 Hz/cm**2 for the oiled RPC, both at 10.0kV which is about 100 V above the 95% knee of the efficiency curve.

  16. chloride mass balance

    African Journals Online (AJOL)

    Agadaga

    1Geology Department, Faculty of Sciences and Techniques, University ... characterization of groundwater, rainfall and the unsaturated zone were also carried out using a .... 2008 in collaboration with the Senegal National Meteorological .... [Cl]sm is estimated as average chloride concentration in ..... sands of Australia.

  17. Chloride ingress prediction

    DEFF Research Database (Denmark)

    Frederiksen, Jens Mejer; Geiker, Mette Rica

    2008-01-01

    and time, and where both the surface chloride concentration and the diffusion coefficient are allowed to vary in time; the Mejlbro-Poulsen model is the general solution to Fick’s 2nd law. The paper also presents conversion formulas for the four decisive but rather abstract parameters to parameters, which...

  18. A High Throughput Workflow Environment for Cosmological Simulations

    CERN Document Server

    Erickson, Brandon M S; Evrard, August E; Becker, Matthew R; Busha, Michael T; Kravtsov, Andrey V; Marru, Suresh; Pierce, Marlon; Wechsler, Risa H

    2012-01-01

    The next generation of wide-area sky surveys offer the power to place extremely precise constraints on cosmological parameters and to test the source of cosmic acceleration. These observational programs will employ multiple techniques based on a variety of statistical signatures of galaxies and large-scale structure. These techniques have sources of systematic error that need to be understood at the percent-level in order to fully leverage the power of next-generation catalogs. Simulations of large-scale structure provide the means to characterize these uncertainties. We are using XSEDE resources to produce multiple synthetic sky surveys of galaxies and large-scale structure in support of science analysis for the Dark Energy Survey. In order to scale up our production to the level of fifty 10^10-particle simulations, we are working to embed production control within the Apache Airavata workflow environment. We explain our methods and report how the workflow has reduced production time by 40% compared to manua...

  19. Objectively measured habitual physical activity in a highly obesogenic environment.

    Science.gov (United States)

    McLure, S A; Summerbell, C D; Reilly, J J

    2009-05-01

    While the prevalence of overweight and obesity among children continues to grow nationally, prevalence in the North-East of England is among the highest in the UK. The objective of this study was to investigate the habitual physical activity levels in a particularly obesogenic environment in the North-East of England. Eight primary schools were selected using a stratified random sampling frame ranking average deprivation levels. Participating children (n = 246, mean age 10 years) wore an accelerometer (Actigraph, GT-256) over five consecutive days (weekend plus three weekdays). Total daily moderate-to-vigorous intensity physical activity was calculated using thresholds by Puyau and colleagues. Only 7% (17/246) of children were sufficiently active. Boys were more physically active than girls (766 +/- 268 vs. 641 +/- 202 counts/min, 95% CI for the difference 63-186 cpm.). Total physical activity was not influenced significantly by deprivation levels or weight status, and there were no significant differences in physical activity between school or weekend days. The North-East of England is a recognized 'hot spot' for paediatric obesity and the present study shows that low levels of habitual physical activity are typical. Choice of accelerometry threshold affects both the apparent amount of physical activity and the ability to detect groups with particularly low levels of physical activity.

  20. Hardening electronic devices against very high total dose radiation environments

    Science.gov (United States)

    Buchanan, B.; Shedd, W.; Roosild, S.; Dolan, R.

    1972-01-01

    The possibilities and limitations of hardening silicon semiconductor devices to the high neutron and gamma radiation levels and greater than 10 to the eighth power rads required for the NERVA nuclear engine development are discussed. A comparison is made of the high dose neutron and gamma hardening potential of bipolar, metal insulator semiconductors and junction field effect transistors. Experimental data is presented on device degradation for the high neutron and gamma doses. Previous data and comparisons indicate that the JFET is much more immune to the combined neutron displacement and gamma ionizing effects than other transistor types. Experimental evidence is also presented which indicates that p channel MOS devices may be able to meet the requirements.

  1. Chloride ingress profiles measured by electron probe micro analysis

    Energy Technology Data Exchange (ETDEWEB)

    Jensen, O.M. [Univ. of Aberdeen (United Kingdom). Dept. of Chemistry]|[Technical Univ. of Denmark, Lyngby (Denmark). Dept. of Structural Engineering and Materials; Coats, A.M.; Glasser, F.P. [Univ. of Aberdeen (United Kingdom). Dept. of Chemistry

    1996-11-01

    Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA is demonstrated to determine chloride ingress in cement paste on a micrometer scale. Potential chloride ingress routes such as cracks or the paste-aggregate interface may also be characterized by EPMA.

  2. Development of Thin Film Ceramic Thermocouples for High Temperature Environments

    Science.gov (United States)

    Wrbanek, John D.; Fralick, Gustave C.; Farmer, Serene C.; Sayir, Ali; Blaha, Charles A.; Gonzalez, Jose M.

    2004-01-01

    The maximum use temperature of noble metal thin film thermocouples of 1100 C (2000 F) may not be adequate for use on components in the increasingly harsh conditions of advanced aircraft and next generation launch technology. Ceramic-based thermocouples are known for their high stability and robustness at temperatures exceeding 1500 C, but are typically found in the form of rods or probes. NASA Glenn Research Center is investigating the feasibility of ceramics as thin film thermocouples for extremely high temperature applications to take advantage of the stability and robustness of ceramics and the non-intrusiveness of thin films. This paper will discuss the current state of development in this effort.

  3. Reliability of High I/O High Density CCGA Interconnect Electronic Packages under Extreme Thermal Environment

    Science.gov (United States)

    Ramesham, Rajeshuni

    2012-01-01

    This paper provides the experimental test results of advanced CCGA packages tested in extreme temperature thermal environments. Standard optical inspection and x-ray non-destructive inspection tools were used to assess the reliability of high density CCGA packages for deep space extreme temperature missions. Ceramic column grid array (CCGA) packages have been increasing in use based on their advantages such as high interconnect density, very good thermal and electrical performances, compatibility with standard surface-mount packaging assembly processes, and so on. CCGA packages are used in space applications such as in logic and microprocessor functions, telecommunications, payload electronics, and flight avionics. As these packages tend to have less solder joint strain relief than leaded packages or more strain relief over lead-less chip carrier packages, the reliability of CCGA packages is very important for short-term and long-term deep space missions. We have employed high density CCGA 1152 and 1272 daisy chained electronic packages in this preliminary reliability study. Each package is divided into several daisy-chained sections. The physical dimensions of CCGA1152 package is 35 mm x 35 mm with a 34 x 34 array of columns with a 1 mm pitch. The dimension of the CCGA1272 package is 37.5 mm x 37.5 mm with a 36 x 36 array with a 1 mm pitch. The columns are made up of 80% Pb/20%Sn material. CCGA interconnect electronic package printed wiring polyimide boards have been assembled and inspected using non-destructive x-ray imaging techniques. The assembled CCGA boards were subjected to extreme temperature thermal atmospheric cycling to assess their reliability for future deep space missions. The resistance of daisy-chained interconnect sections were monitored continuously during thermal cycling. This paper provides the experimental test results of advanced CCGA packages tested in extreme temperature thermal environments. Standard optical inspection and x-ray non

  4. Reliability of High I/O High Density CCGA Interconnect Electronic Packages under Extreme Thermal Environment

    Science.gov (United States)

    Ramesham, Rajeshuni

    2012-01-01

    This paper provides the experimental test results of advanced CCGA packages tested in extreme temperature thermal environments. Standard optical inspection and x-ray non-destructive inspection tools were used to assess the reliability of high density CCGA packages for deep space extreme temperature missions. Ceramic column grid array (CCGA) packages have been increasing in use based on their advantages such as high interconnect density, very good thermal and electrical performances, compatibility with standard surface-mount packaging assembly processes, and so on. CCGA packages are used in space applications such as in logic and microprocessor functions, telecommunications, payload electronics, and flight avionics. As these packages tend to have less solder joint strain relief than leaded packages or more strain relief over lead-less chip carrier packages, the reliability of CCGA packages is very important for short-term and long-term deep space missions. We have employed high density CCGA 1152 and 1272 daisy chained electronic packages in this preliminary reliability study. Each package is divided into several daisy-chained sections. The physical dimensions of CCGA1152 package is 35 mm x 35 mm with a 34 x 34 array of columns with a 1 mm pitch. The dimension of the CCGA1272 package is 37.5 mm x 37.5 mm with a 36 x 36 array with a 1 mm pitch. The columns are made up of 80% Pb/20%Sn material. CCGA interconnect electronic package printed wiring polyimide boards have been assembled and inspected using non-destructive x-ray imaging techniques. The assembled CCGA boards were subjected to extreme temperature thermal atmospheric cycling to assess their reliability for future deep space missions. The resistance of daisy-chained interconnect sections were monitored continuously during thermal cycling. This paper provides the experimental test results of advanced CCGA packages tested in extreme temperature thermal environments. Standard optical inspection and x-ray non

  5. Seizing Workplace Learning Affordances in High-Pressure Work Environments

    DEFF Research Database (Denmark)

    Gnaur, Dorina

    2010-01-01

    to transcend the structuring influence of technology and management regulation. Noticeably, such a manifestation of agency is also aligned with workplace learning when seen as active engagement in work practices. Contrary to universalistic accounts of neo-Tayloristic assembly line workplaces with high levels...

  6. Study of Copper Substitute in High Copper Price Market Environment

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    <正>The high price of copper drives up industry cost,also it is difficult for terminal products to raise price to transfer the cost pressure brought by increase in copper price,as a result downstream consumption markets instead try to seek

  7. Strontium mono-chloride — A new molecule for the determination of chlorine using high-resolution graphite furnace molecular absorption spectrometry and direct solid sample analysis

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, Éderson R. [Departamento de Química, Universidade Federal de Santa Catarina, 88040-900 Florianópolis, SC (Brazil); Welz, Bernhard, E-mail: w.bernardo@terra.com.br [Departamento de Química, Universidade Federal de Santa Catarina, 88040-900 Florianópolis, SC (Brazil); Instituto Nacional de Ciência e Tecnologia do CNPq, INCT de Energia e Ambiente, Universidade Federal da Bahia, 40170-115 Salvador, BA (Brazil); Lopez, Alfredo H.D.; Gois, Jefferson S. de; Caramori, Giovanni F. [Departamento de Química, Universidade Federal de Santa Catarina, 88040-900 Florianópolis, SC (Brazil); Borges, Daniel L.G.; Carasek, Eduardo [Departamento de Química, Universidade Federal de Santa Catarina, 88040-900 Florianópolis, SC (Brazil); Instituto Nacional de Ciência e Tecnologia do CNPq, INCT de Energia e Ambiente, Universidade Federal da Bahia, 40170-115 Salvador, BA (Brazil); Andrade, Jailson B. de [Instituto Nacional de Ciência e Tecnologia do CNPq, INCT de Energia e Ambiente, Universidade Federal da Bahia, 40170-115 Salvador, BA (Brazil)

    2014-12-01

    A new method has been developed for the determination of chlorine in biological reference materials using high-resolution continuum source graphite furnace molecular absorption spectrometry (HR-CS GF MAS) of the strontium mono-chloride (SrCl) molecule and direct solid sample analysis. The use of the SrCl molecule for high-temperature MAS was not described up to now in the literature. Preliminary time-dependent density functional theory calculations of the SrCl structure were carried out in order to obtain reasonable estimates of the absorption spectrum of the target molecule. The calculations, which were carried out at BHandHLyp/def2-QZVP level of theory, proved a very accurate and inexpensive way to get information about the spectrum of the SrCl molecule, which enabled us to perform the Cl determination with good sensitivity and specificity. The molecular absorption of the SrCl molecule has been measured using the wavelength at 635.862 nm, and zirconium and palladium have been evaluated as the chemical modifiers in order to increase the sensitivity of the gaseous SrCl molecule generated in the graphite furnace. The pyrolysis and vaporization temperatures were 600 °C and 2300 °C, respectively. Accuracy and precision of the method have been evaluated using biological certified reference materials of both animal and plant origins, showing good agreement with the informed and certified values. Limit of detection and characteristic mass were 1.0 and 2.2 ng, respectively. The results found using HR-CS GF MAS were in agreement (95% confidence level) compared to those obtained by electrothermal vaporization-inductively coupled plasma mass spectrometry. - Highlights: • The spectrum of the SrCl molecule was calculated on a theoretical basis and found very close to the predicted wavelength. • It is the first time that the spectrum of the SrCl molecule is described and used analytically for the determination of Cl. • No spectral interferences were observed as the

  8. MDT Performance in a High Rate Background Environment

    CERN Document Server

    Aleksa, Martin; Hessey, N P; Riegler, W

    1998-01-01

    A Cs137 gamma source with different lead filters in the SPS beam-line X5 has been used to simulate the ATLAS background radiation. This note shows the impact of high background rates on the MDT efficiency and resolution for three kinds of pulse shaping and compares the results with GARFIELD simulations. Furthermore it explains how the performance can be improved by time slewing corrections and double track separation.

  9. Effect of Steam-Autoclaved Curing on Chloride Permeability of High Strength Concrete%二次高温养护对高强混凝土抗 Cl-渗透性的影响

    Institute of Scientific and Technical Information of China (English)

    刘东升; 朱建舟; 谭克锋

    2014-01-01

    利用氯离子快速渗透法(RCM)研究了普通蒸汽养护后(80℃,0.1 MPa)再进行压蒸(180℃,1 MPa)养护,即二次高温养护,对不同胶凝材料体系的高强混凝土抗Cl-渗透性的影响。结果表明:对于纯水泥混凝土,与标养相比,“蒸养-压蒸”养护使混凝土抗Cl -渗透性能劣化。掺入粉煤灰、矿粉以及硅灰以等比例取代水泥时,“蒸养-压蒸”都较为充分地激发了上述混合材的火山灰活性,但不同掺合料对“蒸养-压蒸”后高强混凝土抗Cl-渗透性能影响差别较大。 XRD和SEM研究表明上述结果的产生与高温下水化产物的种类和分布有关。%Rapid choloride migration test (RCMT) was used to investigate the influence of curing methods and mineral admixtures on chloride ingress resistance of high strength concrete .The results indicate that steam cu-ring and autoclaving curing , especially autoclaving curing , considerably aggravated the chloride penetration through pure cement concrete when compared with normal curing .Incorporating silica fume can improve the chloride ingress resistance of steam curing concrete but degrades autoclaving curing concrete .Adding fly ash with low pozzolanic activity can increase chloride ingress resistance of autoclaving curing concrete , while chlo-ride penetration resistance of steam curing concrete becomes lower .The measure of multi-elements mineral admixtures mixing is propitious to improving the chloride ingress resistance of concrete compared with pure ce-ment concrete under same curing conditions .Results above was analyzed by XRD and SEM .

  10. Co-alignment between Environment Risk, Capital Structure, Growth and High-tech Firm Performance

    Institute of Scientific and Technical Information of China (English)

    LI Yan-xi; BAO Shi-ze

    2007-01-01

    To examine whether there is a co-alignment relationship between environment risk, capital structure, growth and high-tech firm performance, the environment risk was measured from the viewpoint of environment change, the long-term debt ratio was adopted as the measure of the capital structure, and the total asset growth and sales growth were chosen to measure the growth of high-tech firms. Regression analysis shows that there is a significant relationship between environment risk, growth and performance of hightech firms measured by the return on equity and cash flow, respectively.

  11. Chloride regulates afferent arteriolar contraction in response to depolarization

    DEFF Research Database (Denmark)

    Hansen, P B; Jensen, B L; Skott, O

    1998-01-01

    . The results show that K+-induced contraction of smooth muscle cells in the afferent arteriole is highly sensitive to chloride, whereas neurotransmitter release and ensuing contraction is not dependent on chloride. Thus, there are different activation pathways for depolarizing vasoconstrictors......-Renal vascular reactivity is influenced by the level of dietary salt intake. Recent in vitro data suggest that afferent arteriolar contractility is modulated by extracellular chloride. In the present study, we assessed the influence of chloride on K+-induced contraction in isolated perfused rabbit...... afferent arterioles. In 70% of vessels examined, K+-induced contraction was abolished by acute substitution of bath chloride. Consecutive addition of Cl- (30, 60, 80, 100, 110, and 117 mmol/L) restored the sensitivity to K+, and half-maximal response was observed at 82 mmol/L chloride. The calcium channel...

  12. Achieving High Resolution Timer Events in Virtualized Environment.

    Science.gov (United States)

    Adamczyk, Blazej; Chydzinski, Andrzej

    2015-01-01

    Virtual Machine Monitors (VMM) have become popular in different application areas. Some applications may require to generate the timer events with high resolution and precision. This however may be challenging due to the complexity of VMMs. In this paper we focus on the timer functionality provided by five different VMMs-Xen, KVM, Qemu, VirtualBox and VMWare. Firstly, we evaluate resolutions and precisions of their timer events. Apparently, provided resolutions and precisions are far too low for some applications (e.g. networking applications with the quality of service). Then, using Xen virtualization we demonstrate the improved timer design that greatly enhances both the resolution and precision of achieved timer events.

  13. Sensitivity Analysis of Chloride Ion Diffusion in Concrete Subjected to Marine Environment%海工环境混凝土中氯离子扩散敏感性分析

    Institute of Scientific and Technical Information of China (English)

    郝风田; 路影

    2013-01-01

    The sufficient attention may be paid attention to the durability of reinforced concrete structure all over the world at present .The concrete structures would be subjected to chloride ingress ,resulting in the corrosion of reinforcing bars ,inducing early deterioration and losing their durability ,and this is a main problem in engineering practices .Based on the second Fick’s law ,and taking into account the surface chloride concentration ,temperature ,water cement ratio , and initial chloride content ,the chloride ion diffusion is calculated and analyzed here .The sensitivity analysis shows that the influence factors of surface chloride concentration ,temperature ,water cement ratio of concrete are obvious ,and the influence of initial chloride content is weaker .%混凝土结构耐久性问题是当今世界普遍关注的问题。由于氯离子侵蚀,导致钢筋锈蚀,使结构发生早期破坏,丧失了结构的耐久性能,已成为实际工程中的重要问题。基于 Fick 第二定律,分别考虑表面氯离子浓度、温度、水灰比、初始氯离子含量,计算氯离子扩散。敏感性分析表明表面氯离子浓度、温度、水灰比对混凝土中氯离子扩散影响较大,初始氯离子含量影响较小。

  14. Fast Timing for High-Rate Environments with Micromegas

    CERN Document Server

    Papaevangelou, Thomas; Ferrer-Ribas, Esther; Giomataris, Ioannis; Godinot, Cyprien; Gonzalez Diaz, Diego; Gustavsson, Thomas; Kebbiri, Mariam; Oliveri, Eraldo; Resnati, Filippo; Ropelewski, Leszek; Tsiledakis, Georgios; Veenhof, Rob; White, Sebastian

    2016-01-01

    The current state of the art in fast timing resolution for existing experiments is of the order of 100 ps on the time of arrival of both charged particles and electromagnetic showers. Current R&D on charged particle timing is approaching the level of 10 ps but is not primarily directed at sustained performance at high rates and under high radiation (as would be needed for HL-LHC pileup mitigation). We demonstrate a Micromegas based solution to reach this level of performance. The Micromegas acts as a photomultiplier coupled to a Cerenkov-radiator front window, which produces sufficient UV photons to convert the ~100 ps single-photoelectron jitter into a timing response of the order of 10-20 ps per incident charged particle. A prototype has been built in order to demonstrate this performance. The first laboratory tests with a pico-second laser have shown a time resolution of the order of 27 ps for ~50 primary photoelectrons, using a bulk Micromegas readout.

  15. Ceramic resistive plate chambers for high rate environments

    Energy Technology Data Exchange (ETDEWEB)

    Laso Garcia, Alejandro; Kaspar, Marcus; Kaempfer, Burkhard; Kotte, Roland; Naumann, Lothar; Stach, Daniel; Wendisch, Christian; Wuestenfeld, Joern [Helmholtz-Zentrum Dresden-Rossendorf, Dresden, Sachsen (Germany); Collaboration: CBM-Collaboration

    2013-07-01

    The future Compressed Baryonic Matter Experiment to be built at FAIR is foreseen to use Resistive Plate Chambers as Time of Flight detectors. However, for the most central part of the ToF Wall high particle fluxes are expected, the simulations predict fluxes in the order of 2.10{sup 4} particles/cm{sup 2} s and even higher the closer the wall approaches the beampipe. This high fluxes show the need to develop new materials. At Helmholtz-Zentrum Dresden Rossendorf, new semiconductor ceramic composites have been developed, several prototypes of RPCs with ceramic electrodes up to 20 x 20 cm{sup 2} have been developed and tested. In this talk, the performance of this detectors in electron (ELBE) and proton (COSY) beams is presented, as well as, the performance of this detectors under irradiation in Ni+Pb collisions at 1.9 AGeV (SIS18, GSI). This performance can be quantified as an efficiency close to 100% and a time resolution better than 100 ps.

  16. Fire's effect on chloride ingress related durability of concrete structure

    Institute of Scientific and Technical Information of China (English)

    JIN Wei-liang; ZHANG Yi

    2007-01-01

    This paper describes the effects of fire on durability of reinforced concrete structures, and points out that fire not only damages the chemical composition and physical structure of concrete by high temperature, but also leads to an additional risk due to the generation of polyvinyl chloride (PVC)combustion gases. A mathematical model is proposed to calculate chloride ingress profiles in fire damaged concrete, so as to explore the service life prediction of the structure. Rapid Chloride Migration (RCM) test was carried out to determine the chloride diffusion coefficients for the application of the mathematical model. Finally, the detected results of a reported case testified to the validity of the mathematical model.

  17. Achieving High Resolution Timer Events in Virtualized Environment.

    Directory of Open Access Journals (Sweden)

    Blazej Adamczyk

    Full Text Available Virtual Machine Monitors (VMM have become popular in different application areas. Some applications may require to generate the timer events with high resolution and precision. This however may be challenging due to the complexity of VMMs. In this paper we focus on the timer functionality provided by five different VMMs-Xen, KVM, Qemu, VirtualBox and VMWare. Firstly, we evaluate resolutions and precisions of their timer events. Apparently, provided resolutions and precisions are far too low for some applications (e.g. networking applications with the quality of service. Then, using Xen virtualization we demonstrate the improved timer design that greatly enhances both the resolution and precision of achieved timer events.

  18. A high performance scientific cloud computing environment for materials simulations

    CERN Document Server

    Jorissen, Kevin; Rehr, John J

    2011-01-01

    We describe the development of a scientific cloud computing (SCC) platform that offers high performance computation capability. The platform consists of a scientific virtual machine prototype containing a UNIX operating system and several materials science codes, together with essential interface tools (an SCC toolset) that offers functionality comparable to local compute clusters. In particular, our SCC toolset provides automatic creation of virtual clusters for parallel computing, including tools for execution and monitoring performance, as well as efficient I/O utilities that enable seamless connections to and from the cloud. Our SCC platform is optimized for the Amazon Elastic Compute Cloud (EC2). We present benchmarks for prototypical scientific applications and demonstrate performance comparable to local compute clusters. To facilitate code execution and provide user-friendly access, we have also integrated cloud computing capability in a JAVA-based GUI. Our SCC platform may be an alternative to traditi...

  19. Ultracold molecular Rydberg physics in a high density environment

    CERN Document Server

    Eiles, Matthew T; Robicheaux, F; Greene, Chris H

    2016-01-01

    Sufficiently high densities in Bose-Einstein condensates provide favorable conditions for the production of ultralong-range polyatomic molecules consisting of one Rydberg atom and a number of neutral ground state atoms. The chemical binding properties and electronic wave functions of these exotic molecules are investigated analytically via hybridized diatomic states. The effects of the molecular geometry on the system's properties are studied through comparisons of the adiabatic potential curves and electronic structures for both symmetric and randomly configured molecular geometries. General properties of these molecules with increasing numbers of constituent atoms and in different geometries are presented. These polyatomic states have spectral signatures that lead to non-Lorentzian line-profiles.

  20. Catalytic Conversion of Cellulose to Levulinic Acid by Metal Chlorides

    Directory of Open Access Journals (Sweden)

    Beixiao Zhang

    2010-08-01

    Full Text Available The catalytic performance of various metal chlorides in the conversion of cellulose to levulinic acid in liquid water at high temperatures was investigated. The effects of reaction parameters on the yield of levulinic acid were also explored. The results showed that alkali and alkaline earth metal chlorides were not effective in conversion of cellulose, while transition metal chlorides, especially CrCl3, FeCl3 and CuCl2 and a group IIIA metal chloride (AlCl3, exhibited high catalytic activity. The catalytic performance was correlated with the acidity of the reaction system due to the addition of the metal chlorides, but more dependent on the type of metal chloride. Among those metal chlorides, chromium chloride was found to be exceptionally effective for the conversion of cellulose to levulinic acid, affording an optimum yield of 67 mol % after a reaction time of 180 min, at 200 °C, with a catalyst dosage of 0.02 M and substrate concentration of 50 wt %. Chromium metal, most of which was present in its oxide form in the solid sample and only a small part in solution as Cr3+ ion, can be easily separated from the resulting product mixture and recycled. Finally, a plausible reaction scheme for the chromium chloride catalyzed conversion of cellulose in water was proposed.

  1. Calcium aluminate cement hydration in a high alkalinity environment

    Directory of Open Access Journals (Sweden)

    Palomo, Á.

    2009-03-01

    Full Text Available The present paper forms part of a broader research project that aims primarily to devise new cementitious products via the alkali activation of silico-aluminous materials. This work addresses the possibility of using small percentages of calcium aluminate cement (CAC as a source of reactive aluminium. For this reason, a preliminary review was needed of the behaviour of CACs in highly alkaline media (2, 8 and 12M NaOH solutions. Two, 28- and 180-day mechanical strength was determined and the reaction products were characterized with XRD and FTIR. The water-hydrated CAC was used as the control.The results obtained showed that CAC hardening took place much more slowly in highly alkaline media than in water. Nonetheless, the 28-day compressive strength obtained, ≥80MPa. As main reaction products, to ambient temperature and from the two days of cured, cubic aluminate C3AH6, and AH3 polymorphs are formed, instead of the usual hexagonal aluminatos (CAH10 and C2AH8 that are formed in the normal hydrate with water.El presente trabajo forma parte de una amplia investigación cuyo objetivo principal es el de elaborar nuevos materiales con propiedades cementantes mediante la activación alcalina de materiales de naturaleza silito-aluminosa. En estos estudios se contempla la posibilidad de utilizar pequeños porcentajes de cemento de aluminato de calcio (CAC como fuente de aluminio reactivo. Por ello inicialmente se ha estudiado el comportamiento de los CAC en medios fuertemente alcalinos (disoluciones de NaOH 2M, 8M y 12M. Se determinaron las resistencias mecánicas a 2, 28 y 180 días y se realizó una caracterización de los productos de reacción formados por DRX, FTIR. Como sistema de referencia se consideró la hidratación del CAC con agua.Los resultados obtenidos muestran que en medios fuertemente alcalinos se retrasan los procesos de rápido endurecimiento de CAC con agua. No obstante a 28 días se obtienen valores de resistencia a compresión

  2. Ceramic resistive plate chambers for high rate environments

    Energy Technology Data Exchange (ETDEWEB)

    Laso Garcia, Alejandro; Kaempfer, Burkhard; Kaspar, Markus; Kotte, Roland; Peschke, Richard; Stach, Daniel; Wendisch, Christian; Wuestenfeld, Joern [Helmholtz Zentrum, Dresden-Rossendorf (Germany); Collaboration: CBM-Collaboration

    2012-07-01

    Multi-gap resistive plate chambers will be used to build the time of flight wall of the compressed baryonic matter experiment (CBM) at FAIR with a time resolution better than 80 ps. The high fluxes expected at the innermost part of the detector, 20 x 10{sup 3} cm{sup -2}s{sup -1} have made necessary the development of new materials capable of withstanding such fluxes. At Helmholtz Zentrum Dresden-Rossendorf, several RPC prototypes of 10 x 10 cm{sup 2} and 20 x 20 cm{sup 2} have been built with ceramic plates with bulk resistivities in the range of 10{sup 9}-10{sup 10} Ohm cm. They have been tested at the superconducting electron accelerator facility ELBE with 30 MeV electrons and at COSY, Juelich, with 2.7 Gev/c protons. We present characteristics of the ceramic electrodes and the latest results concerning the performance of these prototypes in electron and proton beams up to fluxes of 10{sup 6} cm{sup -2}s{sup -1}.

  3. Diamond and silicon pixel detectors in high radiation environments

    Energy Technology Data Exchange (ETDEWEB)

    Tsung, Jieh-Wen

    2012-10-15

    Diamond pixel detector is a promising candidate for tracking of collider experiments because of the good radiation tolerance of diamond. The diamond pixel detector must withstand the radiation damage from 10{sup 16} particles per cm{sup 2}, which is the expected total fluence in High Luminosity Large Hadron Collider. The performance of diamond and silicon pixel detectors are evaluated in this research in terms of the signal-to-noise ratio (SNR). Single-crystal diamond pixel detectors with the most recent readout chip ATLAS FE-I4 are produced and characterized. Based on the results of the measurement, the SNR of diamond pixel detector is evaluated as a function of radiation fluence, and compared to that of planar-silicon ones. The deterioration of signal due to radiation damage is formulated using the mean free path of charge carriers in the sensor. The noise from the pixel readout circuit is simulated and calculated with leakage current and input capacitance to the amplifier as important parameters. The measured SNR shows good agreement with the calculated and simulated results, proving that the performance of diamond pixel detectors can exceed the silicon ones if the particle fluence is more than 10{sup 15} particles per cm{sup 2}.

  4. Analysing the physics learning environment of visually impaired students in high schools

    Science.gov (United States)

    Toenders, Frank G. C.; de Putter-Smits, Lesley G. A.; Sanders, Wendy T. M.; den Brok, Perry

    2017-07-01

    Although visually impaired students attend regular high school, their enrolment in advanced science classes is dramatically low. In our research we evaluated the physics learning environment of a blind high school student in a regular Dutch high school. For visually impaired students to grasp physics concepts, time and additional materials to support the learning process are key. Time for teachers to develop teaching methods for such students is scarce. Suggestions for changes to the learning environment and of materials used are given.

  5. Benzalkonium Chloride and Glaucoma

    OpenAIRE

    Rasmussen, Carol A.; Kaufman, Paul L.; Kiland, Julie A.

    2014-01-01

    Glaucoma patients routinely take multiple medications, with multiple daily doses, for years or even decades. Benzalkonium chloride (BAK) is the most common preservative in glaucoma medications. BAK has been detected in the trabecular meshwork (TM), corneal endothelium, lens, and retina after topical drop installation and may accumulate in those tissues. There is evidence that BAK causes corneal and conjunctival toxicity, including cell loss, disruption of tight junctions, apoptosis and preapo...

  6. Amine and Titanium (IV Chloride, Boron (III Chloride or Zirconium (IV Chloride-Promoted Baylis-Hillman Reactions

    Directory of Open Access Journals (Sweden)

    Shi-Cong Cui

    2001-10-01

    Full Text Available The Baylis-Hillman reactions of various aryl aldehydes with methyl vinyl ketone at temperatures below -20oC using Lewis acids such as titanium (IV chloride, boron (III chloride or zirconium (IV chloride in the presence of a catalytic amount of selected amines used as a Lewis bases afford the chlorinated compounds 1 as the major product in very high yields. Acrylonitrile can also undergo the same reaction to give the corresponding chlorinated product in moderate yield. A plausible reaction mechanism is proposed. However, if the reaction was carried out at room temperature (ca. 20oC, then the Z-configuration of the elimination product 3, derived from 1, was formed as the major product.

  7. Disposal of high level nuclear wastes: Thermodynamic equilibrium and environment ethics

    Institute of Scientific and Technical Information of China (English)

    RANA Mukhtar Ahmed

    2009-01-01

    Contamination of soil, water or air, due to a failure of containment or disposal of high level nuclear wastes, can potentially cause serious hazards to the environment or human health. Essential elements of the environment and radioactivity dangers to it are illustrated. Issues of high level nuclear waste disposal are discussed with a focus on thermodynamic equilibrium and environment ethics. Major aspects of the issues are analyzed and described briefly to build a perception of risks involved and ethical implications. Nuclear waste containment repository should be as close as possible to thermodynamic equilibrium. A clear demonstration about safety aspects of nuclear waste management is required in gaining public and political confidence in any possible scheme of permanent disposal. Disposal of high level nuclear waste offers a spectrum of environment connected challenges and a long term future of nuclear power depends on the environment friendly solution of the problem of nuclear wastes.

  8. Chloride equilibrium potential in salamander cones

    Directory of Open Access Journals (Sweden)

    Bryson Eric J

    2004-12-01

    Full Text Available Abstract Background GABAergic inhibition and effects of intracellular chloride ions on calcium channel activity have been proposed to regulate neurotransmission from photoreceptors. To assess the impact of these and other chloride-dependent mechanisms on release from cones, the chloride equilibrium potential (ECl was determined in red-sensitive, large single cones from the tiger salamander retinal slice. Results Whole cell recordings were done using gramicidin perforated patch techniques to maintain endogenous Cl- levels. Membrane potentials were corrected for liquid junction potentials. Cone resting potentials were found to average -46 mV. To measure ECl, we applied long depolarizing steps to activate the calcium-activated chloride current (ICl(Ca and then determined the reversal potential for the current component that was inhibited by the Cl- channel blocker, niflumic acid. With this method, ECl was found to average -46 mV. In a complementary approach, we used a Cl-sensitive dye, MEQ, to measure the Cl- flux produced by depolarization with elevated concentrations of K+. The membrane potentials produced by the various high K+ solutions were measured in separate current clamp experiments. Consistent with electrophysiological experiments, MEQ fluorescence measurements indicated that ECl was below -36 mV. Conclusions The results of this study indicate that ECl is close to the dark resting potential. This will minimize the impact of chloride-dependent presynaptic mechanisms in cone terminals involving GABAa receptors, glutamate transporters and ICl(Ca.

  9. Teachers' Perceptions of Their Work Environment in Swedish Junior High Schools

    Science.gov (United States)

    Allodi, Mara Westling; Fischbein, Siv

    2012-01-01

    The aims of this study were to explore the organisational characteristics of junior high schools, to identify typologies of work environments and to explore the relationships between the type of work environment and how schools function. The educational profession and the role of teachers have been influenced by policies inspired by the principles…

  10. Energy-Based Tetrahedron Sensor for High-Temperature, High-Pressure Environments

    Science.gov (United States)

    Gee, Kent L.; Sommerfeldt, Scott D.; Blotter, Jonathan D.

    2012-01-01

    An acoustic energy-based probe has been developed that incorporates multiple acoustic sensing elements in order to obtain the acoustic pressure and three-dimensional acoustic particle velocity. With these quantities, the user can obtain various energy-based quantities, including acoustic energy density, acoustic intensity, and acoustic impedance. In this specific development, the probe has been designed to operate in an environment characterized by high temperatures and high pressures as is found in the close vicinity of rocket plumes. Given these capabilities, the probe is designed to be used to investigate the acoustic conditions within the plume of a rocket engine or jet engine to facilitate greater understanding of the noise generation mechanisms in those plumes. The probe features sensors mounted inside a solid sphere. The associated electronics for the probe are contained within the sphere and the associated handle for the probe. More importantly, the design of the probe has desirable properties that reduce the bias errors associated with determining the acoustic pressure and velocity using finite sum and difference techniques. The diameter of the probe dictates the lower and upper operating frequencies for the probe, where accurate measurements can be acquired. The current probe design implements a sphere diameter of 1 in. (2.5 cm), which limits the upper operating frequency to about 4.5 kHz. The sensors are operational up to much higher frequencies, and could be used to acquire pressure data at higher frequencies, but the energy-based measurements are limited to that upper frequency. Larger or smaller spherical probes could be designed to go to lower or higher frequency range

  11. Efficient cellulose solvent: quaternary ammonium chlorides.

    Science.gov (United States)

    Kostag, Marc; Liebert, Tim; El Seoud, Omar A; Heinze, Thomas

    2013-10-01

    Pure quaternary tetraalkylammonium chlorides with one long alkyl chain dissolved in various organic solvents constitute a new class of cellulose solvents. The electrolytes are prepared in high yields and purity by Menshutkin quaternization, an inexpensive and easy synthesis route. The pure molten tetraalkylammonium chlorides dissolve up to 15 wt% of cellulose. Cosolvents, including N,N-dimethylacetamide (DMA), may be added in large excess, leading to a system of decreased viscosity. Contrary to the well-established solvent DMA/LiCl, cellulose dissolves in DMA/quaternary ammonium chlorides without any pretreatment. Thus, the use of the new solvent avoids some disadvantages of DMA/LiCl and ionic liquids, the most extensively employed solvents for homogeneous cellulose chemistry.

  12. cis-Dichloridobis(1,10-phenanthrolinechromium(III chloride

    Directory of Open Access Journals (Sweden)

    Xiaoli Gao

    2011-02-01

    Full Text Available In the title complex, [CrCl2(C12H8N22]Cl, the CrIII ion is situated on a twofold rotation axis and displays a slightly distorted octahedral CrCl2N4 coordination geometry. The Cr environment is composed of a cis arrangement of two 1,10-phenanthroline and two chloride ligands. The chloride counter-anion exhibits half-occupation and is equally disordered over two positions.

  13. Ultrasonic Al2O3 Ceramic Thermometry in High-Temperature Oxidation Environment

    Directory of Open Access Journals (Sweden)

    Yanlong Wei

    2016-11-01

    Full Text Available In this study, an ultrasonic temperature measurement system was designed with Al2O3 high-temperature ceramic as an acoustic waveguide sensor and preliminarily tested in a high-temperature oxidation environment. The test results indicated that the system can indeed work stably in high-temperature environments. The relationship between the temperature and delay time of 26 °C–1600 °C ceramic materials was also determined in order to fully elucidate the high-temperature oxidation of the proposed waveguide sensor and to lay a foundation for the further application of this system in temperatures as high as 2000 °C.

  14. Effects of Interior Plantscapes on Indoor Environments and Stress Level of High School Students

    National Research Council Canada - National Science Library

    So-Young Park; Jin-Su Song; Hyoung-Deug Kim; Kenji Yamane; Ki-Cheol Son

    2008-01-01

      Case studies were performed in two high schools (designated K and J) in Seoul, Korea in order to examine how in-class plantscapes consisting of ornamental plants affected the indoor environment and the stress level of students...

  15. Agent-Based Data Mining Framework for the High-Dimensional Environment

    Institute of Scientific and Technical Information of China (English)

    LI Kan; LIU Yu-shu

    2005-01-01

    An agent-based data mining framework for the high-dimensional environment is built instead of the style of classical structural programming or the object-oriented programming. The framework supports the whole process of data mining of the high-dimensional environment. Belief-desire-joint intention agents are designed to fit the characteristic of the high-dimensional environment. At the same time, the syntax, semantics and reasoning rules of the agents are given. In the data mining system of the high-dimensional environment,agents need exchange messages. The cooperation behavior mechanism is adopted to complete the communication through the three-level pattern among agents that have their own fixed roles.

  16. The Influence of Mineral Functional Materials on Chloride Ion Penetration of Concrete

    Institute of Scientific and Technical Information of China (English)

    HU Hongmei; MA Baoguo

    2005-01-01

    The mechanism of chloride ion penetration in high performance concrete was analyzed. The experimental results indicate that there are two important reasons that influence the anti-chloride penetration of high performance concrete. One is the function effect of mineral functional material, so that it increases concrete's capability to resist chloride ion penetration. The other is combined action of mineral functional material's original capability of binding the chloride ion (physical adsorption) and physicochemical adsorption after hydration.

  17. Stability of Alprostadil in 0.9% Sodium Chloride Stored in Polyvinyl Chloride Containers.

    Science.gov (United States)

    McCluskey, Susan V; Kirkham, Kylian; Munson, Jessica M

    2017-01-01

    The stability of alprostadil diluted in 0.9% sodium chloride stored in polyvinyl chloride (VIAFLEX) containers at refrigerated temperature, protected from light, is reported. Five solutions of alprostadil 11 mcg/mL were prepared in 250 mL 0.9% sodium chloride polyvinyl chloride (PL146) containers. The final concentration of alcohol was 2%. Samples were stored under refrigeration (2°C to 8°C) with protection from light. Two containers were submitted for potency testing and analyzed in duplicate with the stability-indicating high-performance liquid chromatography assay at specific time points over 14 days. Three containers were submitted for pH and visual testing at specific time points over 14 days. Stability was defined as retention of 90% to 110% of initial alprostadil concentration, with maintenance of the original clear, colorless, and visually particulate-free solution. Study results reported retention of 90% to 110% initial alprostadil concentration at all time points through day 10. One sample exceeded 110% potency at day 14. pH values did not change appreciably over the 14 days. There were no color changes or particle formation detected in the solutions over the study period. This study concluded that during refrigerated, light-protected storage in polyvinyl chloride (VIAFLEX) containers, a commercial alcohol-containing alprostadil formulation diluted to 11 mcg/mL with 0.9% sodium chloride 250 mL was stable for 10 days.

  18. Microbial community composition of Tirez lagoon (Spain), a highly sulfated athalassohaline environment

    OpenAIRE

    Montoya, Lilia; Vizioli, Carlotta; Rodríguez, Nuria; Rastoll, María José; Amils, Ricardo; Marín, Irma

    2013-01-01

    Background: The aim was to study the seasonal microbial diversity variations of an athalassohaline environment with a high concentration of sulfates in Tirez lagoon (La Mancha, Spain). Despite the interest in these types of environments there is scarce information about their microbial ecology, especially on their anoxic sediments. Results: We report the seasonal microbial diversity of the water column and the sediments of a highly sulfated lagoon using both molecular and conventional microbi...

  19. The effects of different beverage intake on blood components during exercise under high-temperature environment

    OpenAIRE

    Baek, Soon Gi

    2013-01-01

    High temperature environment causes detrimental effects on health. In the present study, the effects of intake of several kinds of beverage on blood components during exercise under the high temperature environment were evaluated. The 10 subjects were student of the H University. Exercise intensity was 50–60% O2maxx and treadmill exercise was continued for 1 h. The kinds of beverage were water, ion beverage, cucumber drink. Blood sampling was performed before the exercise, immediately finishi...

  20. Reliable content delivery using persistent data sessions in a highly mobile environment

    OpenAIRE

    Pantoleon, Periklis K.

    2004-01-01

    Approved for public release; distribution is unlimited Special Forces are crucial in specific military operations. They usually operate in hostile territory where communications are difficult to establish and preserve, since the operations are often carried out in a remote environment and the communications need to be highly mobile. The delivery of information about the geographical parameters of the area can be crucial for the completion of their mission. But in that highly mobile environ...

  1. 氯化钡除杂制取高纯氢氧化钡%Preparation of high purity barium hydroxide by impurity - removed barium chloride

    Institute of Scientific and Technical Information of China (English)

    翁贤芬; 毛逢银; 何琳; 李莉

    2009-01-01

    Removal technology of strontium and iron from crude barium chloride raw material were studied.Optimization of process conditions of strontium and iron removal were discussed.When crude barium chloride stiring and dissolving the mixture at 60 ℃ for 40 min,impurities of stromtium and calcuim can be removed and mass fraction of strontium in the obatined solid barium chloride was below 1×10-4.Then add oxydol (H2O2) at proportion of 100 g raw materials per 8 mL H2O2,and add active carbon and small quantity of sodium hydroxide.Finally,iron could be get rid of when pH was controlled below 10.Mass fraction of iron in barium hydroxide product was less than 1×10-5 when using the iron - removed barium chaloride as raw material.Therefore,purified barium chloride by this method can be used to produce purity barium hydroxide.%研究了粗氯化钡原料中锶和铁杂质的脱除工艺,探讨了脱除锶和铁的优化工艺条件.在粗氯化钡原料中加入去离子水,液固质量比为0.25: 1,在60 ℃下搅拌溶解40 min,可除去锶和钙杂质,所得氯化钡固体中锶质量分数低于1×10-4.在氯化钡溶液中加入双氧水,每100 g原料中加入双氧水8 mL,加入活性炭和少量氢氧化钠,控制pH低于10时,可除去铁杂质,用除铁后的氯化钡制取氢氧化钡,产品中铁质量分数低于1×10-5.用除杂后的氯化钡可制得高纯氢氧化钡.

  2. Oxomemazine hydro-chloride.

    Science.gov (United States)

    Siddegowda, M S; Butcher, Ray J; Akkurt, Mehmet; Yathirajan, H S; Ramesh, A R

    2011-08-01

    IN THE TITLE COMPOUND [SYSTEMATIC NAME: 3-(5,5-dioxo-phen-othia-zin-10-yl)-N,N,2-trimethyl-propanaminium chloride], C(18)H(23)N(2)O(2)S(+)·Cl(-), the dihedral angle between the two outer aromatic rings of the phenothia-zine unit is 30.5 (2)°. In the crystal, the components are linked by N-H⋯Cl and C-H⋯Cl hydrogen bonds and C-H⋯π inter-actions.

  3. A Miniature Fiber-Optic Sensor for High-Resolution and High-Speed Temperature Sensing in Ocean Environment

    Science.gov (United States)

    2015-11-05

    fiber-optic sensor for high-resolution and high-speed temperature sensing in ocean environment Guigen Liu1, Ming Han1,* Weilin Hou2, Silvia Matt2... sensor performance. In this paper, we present an optical fiber sensor for the high-resolution and high-speed temperature profiling. The developed sensor ...silicon, such as large thermal diffusivity, notable thermo-optic effects and thermal expansion coefficients of silicon, the proposed sensor exhibits

  4. [Environment of high temperature or air particle matter pollution, and health promotion of exercise].

    Science.gov (United States)

    Zhao, Jie-xiu; Xu, Min-xiao; Wu, Zhao-zhao

    2014-10-01

    It is important to keep human health in special environment, since the special environment has different effects on health. In this review, we focused on high temperature and air particle matter environment, and health promotion of exercise. Exercise and high temperature are the main non-pharmacological therapeutic interventions of insulin resistance (IR). PGC-1α is key regulatory factor in health promotion of exercise and high temperature. The novel hormone Irisin might be the important pathway through which heat and exercise could have positive function on IR. Air particle matter (PM) is associated with onset of many respiratory diseases and negative effects of exerciser performance. However, regular exercise plays an important role in improving health of respiratory system and lowering the risk induced by PM. Furthermore, free radicals and inflammatory pathways are included in the possible mechanisms of positive physiological effects induced by exercise in air particle matter environment.

  5. The Transport Properties of Concrete under the Simultaneous Coupling of Fatigue Load and Environment Factors

    Institute of Scientific and Technical Information of China (English)

    WANG Caihui; SUN Wei; JING Jinyang; HAN Jiande; RONG Hui

    2012-01-01

    A set of coupling experimental instrument was designed to study the transport properties of chloride ion in concrete under simultaneous coupling action of fatigue load and environmental factors.Firstly the water-saturated performance of modern concrete was investigated,then diffusion performance of chloride ion under different stress levels and different temperature were studied respectively; meanwhile,the timedependent behavior of the chloride ion diffusion in concrete was also researched.The results showed that the saturation degree of concrete can reach as high as 99%.Besides,diffusion coefficient of chloride ion increased with increasing of the stress level and temperature,and when the stress level and temperature are at 0.6 and 60 ℃ respectively,the diffusion coefficient is 6.3 × 10 14 m2/s,moreover the diffusion coefficient of chloride ion in concrete decreased with time under the simultaneous coupling action of fatigue load and environment factors.

  6. Comparing polyaluminum chloride and ferric chloride for antimony removal.

    Science.gov (United States)

    Kang, Meea; Kamei, Tasuku; Magara, Yasumoto

    2003-10-01

    Antimony has been one of the contaminants required to be regulated, however, only limited information has been collected to date regarding antimony removal by polyaluminium chloride (PACl) and ferric chloride (FC). Accordingly, the possible use of coagulation by PACl or FC for antimony removal was investigated. Jar tests were used to determine the effects of solution pH, coagulant dosage, and pre-chlorination on the removal of various antimony species. Although high-efficiency antimony removal by aluminum coagulation has been expected because antimony is similar to arsenic in that both antimony and arsenic are a kind of metalloid in group V of the periodic chart, this study indicated: (1) removal density (arsenic or antimony removed per mg coagulant) for antimony by PACl was about one forty-fifth as low as observed for As(V); (2) although the removal of both Sb(III) and Sb(V) by coagulation with FC was much higher than that of PACl, a high coagulant dose of 10.5mg of FeL(-1) at optimal pH of 5.0 was still not sufficient to meet the standard antimony level of 2 microg as SbL(-1) for drinking water when around 6 microg as SbL(-1) were initially present. Consequently, investigation of a more appropriate treatment process is necessary to develop economical Sb reduction; (3) although previous studies concluded that As(V) is more effectively removed than As(III), this study showed that the removal of Sb(III) by coagulation with FC was much more pronounced than that of Sb(V); (4) oxidation of Sb(III) with chlorine decreased the ability of FC to remove antimony. Accordingly, natural water containing Sb(III) under anoxic condition should be coagulated without pre-oxidation.

  7. 40 CFR 721.10056 - Benzenemethanaminium, N-(3-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides.

    Science.gov (United States)

    2010-07-01

    ...)-N,N-dimethyl-, N-soya acyl derivs., chlorides. 721.10056 Section 721.10056 Protection of Environment...-aminopropyl)-N,N-dimethyl-, N-soya acyl derivs., chlorides. (a) Chemical substance and significant new uses...-dimethyl-, N-soya acyl derivs., chlorides (PMN P-03-47; CAS No. 90194-13-1) is subject to reporting under...

  8. Relationship of constructivist learning environment to student attitudes and achievement in high school mathematics and science

    Science.gov (United States)

    Dethlefs, Theresa Marie

    This study investigated the relationship of constructivist learning environment and standards-based teaching practices to student achievement and attitudes (self-efficacy, intrinsic value, and learning strategies) in Algebra and Biology. Further, these relationships were examined as a function of student gender and prior achievement. A purposive sample of 804 high school students enrolled in Biology I, Algebra I, or Advanced Algebra was selected for inclusion in this study. Although the dimensions of constructivist learning environment that contributed to predicting student achievement and attitudes varied by content area and criterion, the results of the present study generally provide strong support for a positive relationship between constructivist learning environment and student attitudes, but little support for a direct relationship to student achievement. Teacher reports of overall constructivist learning environment were not correlated with achievement or attitudes. Observer reports of constructivist learning environment were correlated with student intrinsic value and learning strategies. Student reports of constructivist learning environment were correlated with all three attitude measures. Multiple regression findings showed that neither overall constructivist learning environment nor standards-based teaching practices predicted achievement in any of the content areas. Overall constructivist learning environment and standards-based teaching practices were significant positive predictors of student intrinsic value and learning strategies in all three content areas, after controlling for student and classroom demographic variables. Overall constructivist learning environment and standards-based teaching practices were also significant positive predictors of self-efficacy in Algebra 1. In addition, standards-based teaching practices was a significant positive predictor of student self-efficacy in Biology. No specific dimensions of constructivist learning

  9. The secular variation of inner zone high energy proton environment in the SAA

    Institute of Scientific and Technical Information of China (English)

    XIE; Lun; PU; Zuyin; JIAO; Weixin; FU; suiyan

    2005-01-01

    A long-term variation of the inner zone high-energy proton environment at low orbits was investigated by DSTM using the adiabatic approximation of charge particle motion with NASA standard radiation models as reference states. The DST results show that over the past three decades the fluxes of high-energy protons at (1000 km in the South Atlantic Anomaly (SAA) noticeably increased, the center region of proton SAA apparently moved westward and expanded. Calculations of the L-shell averaged lifetime of high-energy protons indicate that the DST provides a reasonable means for estimation of the secular variation of inner zone proton environment.

  10. The evaluation of different environments in ultra-high frequency induction sintered powder metal compacts

    Energy Technology Data Exchange (ETDEWEB)

    Cavdar, P. S.; Cavdar, U.

    2015-03-30

    The application of the iron based Powder Metal (PM) compacts in Ultra-High Frequency Induction Sintering (UHFIS) was reviewed for different environments. The three different environments: atmosphere, argon and vacuum were applied to the PM compacts. Iron based PM compacts were sintered at 1120 degree centigrade for a total of 550 seconds by using induction sintering machines with 2.8 kW power and 900 kHz frequency. Micro structural properties, densities, roughness and micro hardness values were obtained for all environments. The results were compared with each other. (Author)

  11. Thallium magnesium chloride: A high light yield, large effective atomic number, intrinsically activated crystalline scintillator for X-ray and gamma-ray detection

    Science.gov (United States)

    Fujimoto, Yutaka; Koshimizu, Masanori; Yanagida, Takayuki; Okada, Go; Saeki, Keiichiro; Asai, Keisuke

    2016-09-01

    We report the luminescence and the scintillation properties of a newly developed thallium magnesium chloride (TlMgCl3) crystal. The crystal sample can be easily fabricated from the melt using the Bridgman method. The photoluminescence band appeared near the wavelength of 405 nm under excitation at 230 nm. An X-ray-induced scintillation spectrum showed an intense emission band near the wavelength of 405 nm. The decay time constant was estimated to be approximately 60 ns (∼25%) and 350 ns (∼75%) using a bi-exponential fitting. The scintillation light yield reached 46,000 photons/MeV with an energy resolution of 5% at 662 keV.

  12. The Behavior Of Asymmetric Frontal Couplings With Permanent Magnets In Magnetic Powder And High Temperature Environments

    Directory of Open Access Journals (Sweden)

    Ion DOBROTA

    2002-12-01

    Full Text Available The main purpose of this paper is the comparative analysis of the behavior of frontal couplings with Nd-Fe-B permanent magnets in difficult environments, specific to metallurgy – such as environments with magnetic powders and high temperature – in two constructive variants: symmetric couplings and asymmetric couplings (with divided poles. The results show the superior performance of asymmetric couplings under the given conditions

  13. Electroless reduction of silver chloride precipitates for the preparation of highly sensitive substrates for surface-enhanced infrared absorption (SEIRA) measurements.

    Science.gov (United States)

    Rao, Gadupudi Purna Chandra; Yang, Jyisy

    2015-01-01

    To prepare silver nanoparticles (AgNPs) on infrared-transmitting crystal for surface-enhanced infrared absorption (SEIRA) measurements, a new strategy is proposed and demonstrated using electroless reduction of preformed silver chloride (AgCl) particles. Silver chloride precipitates were formed using an additive of polyvinyl pyrrolidone (PVP) to vary the size and shape of the precipitates. After settling on germanium substrates, the preformed particles of AgCl were reduced electrolessly and spontaneously coagulated to AgNPs. The resulting AgNPs showed a multilayer structure, but the AgNPs were isolated, as shown by the lack of absorption-band distortion in the SEIRA measurements. Hence, the sensitivity and analyte-loading capacity for SEIRA measurements are improved significantly. To optimize the chemical deposition and electroless reduction method, we examined several parameters, including the concentrations of reagents during AgCl precipitation and the reaction time required in the deposition-reduction steps. We used para-nitrobenzoic acid (pNBA) to probe the intensity of the SEIRA effect for the prepared substrates. To better correlate the SEIRA performances with each variable, we examined the prepared substrates using a scanning electron microscope and SEIRA. The results indicate that two major morphologies of AgNPs are observed: nanoparticles and nanorods. The distributions of nanorods we observed were related to the procedures used to prepare the substrates. Based on SEIRA signals, we observed enhancement factors approaching three orders of magnitude compared to conventional transmission measurement. Also, based on the morphologies, the large signals were mainly caused by the formation of multilayers of non-percolated AgNPs.

  14. 锂渣钢渣复合高性能混凝土抗氯离子的渗透性能%The Permeability of Resistance to Chloride Ion of High Performance Concrete with Lithium Slag and Steel Slag

    Institute of Scientific and Technical Information of China (English)

    吴福飞; 侍克斌; 努尔开力·依孜特罗甫; 董双快; 胡全

    2012-01-01

    为了提高混凝土抗氯离子渗透能力,在混凝土中掺入具有火山灰性的锂渣和会产生自身水化的钢渣.采用正交设计,通过RCM法测试表明,随着锂渣和钢渣掺入总量的增加,混凝土抗氯离子渗透的能力呈现先增大后减小趋势,以锂渣掺量为25%和钢渣掺量为20%时为最优掺量.在水泥水化后,锂渣参与了二次反应,细化了混凝土界面结构,同时促进了钢渣和水泥的相互水化程度,提高了混凝土抗氯离子渗透的能力.%In order to increase permeability of resistance to chloride ion of high performance concrete,the lithium slag with volcanic ash usability and steel slag producing their own hydration were mixed with the concrete. Using orthogonal design, RCM method tests showed that with the incorporation of lithium slag and steel slag increase in the total,concrete resistant to chloride ion penetration ability first increases and then decreases. Lithium slag dosage for 25% and 20% steel slag was regarded as the optimal dosage. After cement hydration,Lithium slag participated in a secondary reaction,the interface structure of concrete was refined,at the same time the mutual degree of hydration of the steel slag and cement was promoted,the a-bility of concrete resistance to chloride ion penetration was improved.

  15. Phentermine interference and high L-methamphetamine concentration problems in GC-EI-MS SIM Analyses of R-(-)-α-methoxy-α-(trifluoromethyl)phenylacetyl chloride-derivatized amphetamines and methamphetamines†.

    Science.gov (United States)

    Hamilton, Theron J; Qui, Harry Z; Dozier, Katherine V R; Fuller, Zachary J

    2014-09-01

    In order to achieve chromatographic separation, urine samples shown to be initially positive for amphetamines and methamphetamines in US Department of Defense immunoassays are derivatized with R-(-)-α-methoxy-α-(trifluoromethyl)phenylacetyl chloride (R-(-)-MTPA) prior to gas chromatography-electron impact-mass spectrometry (GC-EI-MS) analysis. Phentermine, a member of the phenethylamine class of drugs and a common appetite suppressant, interferes with GC-EI-MS assays of R-(-)-MTPA-derivatized d-amphetamine, degrading the chromatography of the internal standard and analyte ions and skewing concentration calculations. Additionally, when specimens with high concentrations of l-methamphetamine are derivatized with R-(-)-MTPA, signal peaks have the potential to be misidentified by integration software as d-methamphetamine. We have found that replacing R-(-) MTPA with (S)-(+)-α-methoxy-α-(trifluoromethyl)phenylacetyl chloride reduces phentermine interference problems related to internal standard chromatography, reduces the possibility of concentrated l-methamphetamine peaks being misidentified by integration software, improves resolution of d-methamphetamine in the presence of high l-methamphetamine concentrations, and is a cost-neutral change that can be applied to current amphetamines GC-EI-MS methods without the need for method modification.

  16. Probabilistic evaluation of initiation time of chloride-induced corrosion

    Energy Technology Data Exchange (ETDEWEB)

    Val, Dimitri V. [Department of Structural Engineering and Construction Management, Faculty of Civil and Environmental Engineering, Technion, Israel Institute of Technology, Haifa 32000 (Israel)], E-mail: val@tx.technion.ac.il; Trapper, Pavel A. [Department of Structural Engineering and Construction Management, Faculty of Civil and Environmental Engineering, Technion, Israel Institute of Technology, Haifa 32000 (Israel)

    2008-03-15

    The paper presents a model for chloride ingress into concrete. The model accounts for two mechanisms which control the chloride ingress-diffusion and convection. Using one-dimensional (1-D) formulation of the model, the influence of chloride binding and ambient humidity on chloride ingress into concrete has been investigated. Based on results of this investigation parameters for probabilistic analysis have been selected. Probabilistic evaluation of the time to corrosion initiation has then been carried out for a reinforced concrete (RC) wall (1-D problem) and a RC column (2-D problem) in a marine environment. Results of the analysis show that for the same thickness of the concrete cover the probability of corrosion initiation in the corner reinforcing bars of the RC column is much higher than in reinforcing bars in the middle part of the RC wall. The results demonstrate the importance of 2-D modelling for correct prediction of corrosion initiation in such RC elements as columns and beams.

  17. Chloride on the Move

    KAUST Repository

    Li, Bo

    2017-01-09

    Chloride (Cl−) is an essential plant nutrient but under saline conditions it can accumulate to toxic levels in leaves; limiting this accumulation improves the salt tolerance of some crops. The rate-limiting step for this process – the transfer of Cl− from root symplast to xylem apoplast, which can antagonize delivery of the macronutrient nitrate (NO3−) to shoots – is regulated by abscisic acid (ABA) and is multigenic. Until recently the molecular mechanisms underpinning this salt-tolerance trait were poorly defined. We discuss here how recent advances highlight the role of newly identified transport proteins, some that directly transfer Cl− into the xylem, and others that act on endomembranes in ‘gatekeeper’ cell types in the root stele to control root-to-shoot delivery of Cl−.

  18. Benzalkonium chloride and glaucoma.

    Science.gov (United States)

    Rasmussen, Carol A; Kaufman, Paul L; Kiland, Julie A

    2014-01-01

    Glaucoma patients routinely take multiple medications, with multiple daily doses, for years or even decades. Benzalkonium chloride (BAK) is the most common preservative in glaucoma medications. BAK has been detected in the trabecular meshwork (TM), corneal endothelium, lens, and retina after topical drop installation and may accumulate in those tissues. There is evidence that BAK causes corneal and conjunctival toxicity, including cell loss, disruption of tight junctions, apoptosis and preapoptosis, cytoskeleton changes, and immunoinflammatory reactions. These same effects have been reported in cultured human TM cells exposed to concentrations of BAK found in common glaucoma drugs and in the TM of primary open-angle glaucoma donor eyes. It is possible that a relationship exists between chronic exposure to BAK and glaucoma. The hypothesis that BAK causes/worsens glaucoma is being tested experimentally in an animal model that closely reflects human physiology.

  19. 1300-nm gain obtained with dysprosium-doped chloride crystals

    Energy Technology Data Exchange (ETDEWEB)

    Page, R.H.; Schaffers, K.I.; Beach, R.J.; Payne, S.A.; Krupke, W.F.

    1996-03-01

    Dy{sup 3+} - doped chloride crystals have high 1300-nm emission quantum yields. Pump - probe experiments on La Cl{sub 3}:Dy{sup 3+} demonstrate optical gain consistent with predictions based on spectroscopic cross sections and lifetimes.

  20. The role of learning environment on high school chemistry students' motivation and self-regulatory processes

    Science.gov (United States)

    Judd, Jeffrey S.

    Changes to the global workforce and technological advancements require graduating high school students to be more autonomous, self-directed, and critical in their thinking. To reflect societal changes, current educational reform has focused on developing more problem-based, collaborative, and student-centered classrooms to promote effective self-regulatory learning strategies, with the goal of helping students adapt to future learning situations and become life-long learners. This study identifies key features that may characterize these "powerful learning environments", which I term "high self-regulating learning environments" for ease of discussion, and examine the environment's role on students' motivation and self-regulatory processes. Using direct observation, surveys, and formal and informal interviews, I identified perceptions, motivations, and self-regulatory strategies of 67 students in my high school chemistry classes as they completed academic tasks in both high and low self-regulating learning environments. With social cognitive theory as a theoretical framework, I then examined how students' beliefs and processes changed after they moved from low to a high self-regulating learning environment. Analyses revealed that key features such as task meaning, utility, complexity, and control appeared to play a role in promoting positive changes in students' motivation and self-regulation. As embedded cases, I also included four students identified as high self-regulating, and four students identified as low self-regulating to examine whether the key features of high and low self-regulating learning environments played a similar role in both groups. Analysis of findings indicates that key features did play a significant role in promoting positive changes in both groups, with high self-regulating students' motivation and self-regulatory strategies generally remaining higher than the low self-regulating students; this was the case in both environments. Findings

  1. Method for integrated design of low energy buildings with high quality indoor environment

    DEFF Research Database (Denmark)

    Petersen, Steffen

    2008-01-01

    Energy performance and indoor environment have due to new increased regulatory demands become decisive design parameters in the building design process. In order to comply with the increased regulatory demands, we present an integrated design method which argues that the design of buildings must ...... to become the preferred method for integrated design of low energy buildings with high quality indoor environment.......Energy performance and indoor environment have due to new increased regulatory demands become decisive design parameters in the building design process. In order to comply with the increased regulatory demands, we present an integrated design method which argues that the design of buildings must...... start on room level rather than total building level. The proposed method starts with the establishment of design goals, including goals regarding energy performance and indoor environment, followed by a building physical analysis of performance-decisive parameters. This analysis is used to establish...

  2. Corrosion and Creep of Candidate Alloys in High Temperature Helium and Steam Environments for the NGNP

    Energy Technology Data Exchange (ETDEWEB)

    Was, Gary; Jones, J. W.

    2013-06-21

    This project aims to understand the processes by which candidate materials degrade in He and supercritical water/steam environments characteristic of the current NGNP design. We will focus on understanding the roles of temperature, and carbon and oxygen potential in the 750-850 degree C range on both uniform oxidation and selective internal oxidation along grain boundaries in alloys 617 and 800H in supercritical water in the temperature range 500-600 degree C; and examining the application of static and cyclic stresses in combination with impure He environments in the temperature rang 750-850 degree C; and examining the application of static and cyclic stresses in combination with impure He environments in the temperature range 750-850 degree C over a range of oxygen and carbon potentials in helium. Combined, these studies wil elucidate the potential high damage rate processes in environments and alloys relevant to the NGNP.

  3. Comparative biocidal activity of peracetic acid, benzalkonium chloride and ortho-phthalaldehyde on 77 bacterial strains.

    Science.gov (United States)

    Bridier, A; Briandet, R; Thomas, V; Dubois-Brissonnet, F

    2011-07-01

    Despite numerous reports on biocide activities, it is often difficult to have a reliable and relevant overview of bacterial resistance to disinfectants because each work challenges a limited number of strains and tested methods are often different. The aim of this study was to evaluate the bactericidal activity of three different disinfectants commonly used in industrial or medical environments (peracetic acid, benzalkonium chloride and ortho-phthalaldehyde) against 77 bacterial strains from different origins using one standard test method (NF EN 1040). Results highlight the existence of high interspecific variability of resistance to disinfectants and, contrary to widespread belief, Gram-positive strains generally appeared more resistant than Gram-negative strains. Resistance was also variable among strains of the same species such as Bacillus subtilis to peracetic acid, Pseudomonas aeruginosa to benzalkonium chloride and Staphylococcus aureus to ortho-phthalaldehyde.

  4. Efficient acetylation of primary amines and amino acids in environmentally benign brine solution using acetyl chloride

    Indian Academy of Sciences (India)

    Kaushik Basu; Suchandra Chakraborty; Achintya Kumar Sarkar; Chandan Saha

    2013-05-01

    Acetyl chloride is one of the most commonly available and cheap acylating agent but its high reactivity and concomitant instability in water precludes its use to carry out acetylation in aqueous medium. The present methodology illustrates the efficient acetylation of primary amines and amino acids in brine solution by means of acetyl chloride under weakly basic condition in the presence of sodium acetate and/or triethyl amine followed by trituration with aqueous saturated bicarbonate solution. This effort represents the first efficient use of this most reactive but cheap acetylating agent to acetylate amines in excellent yields in aqueous medium. This is a potentially useful green chemical transformation where reaction takes place in environment-friendly brine solution leading to easy work-up and isolation of the amide derivatives. Mechanistic rationale of this methodology is also important.

  5. Conductor of high electrical current at high temperature in oxygen and liquid metal environment

    Energy Technology Data Exchange (ETDEWEB)

    Powell, IV, Adam Clayton; Pati, Soobhankar; Derezinski, Stephen Joseph; Lau, Garrett; Pal, Uday B.; Guan, Xiaofei; Gopalan, Srikanth

    2016-01-12

    In one aspect, the present invention is directed to apparatuses for and methods of conducting electrical current in an oxygen and liquid metal environment. In another aspect, the invention relates to methods for production of metals from their oxides comprising providing a cathode in electrical contact with a molten electrolyte, providing a liquid metal anode separated from the cathode and the molten electrolyte by a solid oxygen ion conducting membrane, providing a current collector at the anode, and establishing a potential between the cathode and the anode.

  6. Understanding microwave vessel contamination by chloride species.

    Science.gov (United States)

    Recchia, Sandro; Spanu, Davide; Bianchi, Davide; Dossi, Carlo; Pozzi, Andrea; Monticelli, Damiano

    2016-10-01

    Microwaves are widely used to assist digestion, general sample treatment and synthesis. The use of aqua regia is extensively adopted for the closed vessel mineralization of samples prior to trace element detection, leading to the contamination of microwave vessels by chlorine containing species. The latter are entrapped in the polymeric matrix of the vessels, leading to memory effects that are difficult to remove, among which the risk of silver incomplete recoveries by removal of the sparingly soluble chloride is the predominant one. In the present paper, we determined by mass spectrometry that hydrogen chloride is the species entrapped in the polymeric matrix and responsible for vessel contamination. Moreover, several decontamination treatments were considered to assess their efficiency, demonstrating that several cleaning cycles with water, nitric acid or silver nitrate in nitric acid were inefficient in removing chloride contamination (contamination reduction around 90%). Better results (≈95% decrease) were achieved by a single decontamination step in alkaline environment (sodium hydroxide or ammonia). Finally, a thermal treatment in a common laboratory oven (i.e. without vacuum and ventilation) was tested: a one hour heating at 150°C leads to a 98.5% decontamination, a figure higher than the ones obtained by wet treatments which requires comparable time. The latter treatment is a major advancement with respect to existing treatments as it avoids the need of a vacuum oven for at least 17h as presently proposed in the literature.

  7. Factors influencing student perceptions of high-school science laboratory environments.

    Science.gov (United States)

    Luketic, Christine D; Dolan, Erin L

    2013-04-01

    Science laboratory learning has been lauded for decades for its role in fostering positive student attitudes about science and developing students' interest in science and ability to use equipment. An expanding body of research has demonstrated the significant influence of laboratory environment on student learning. Further research has demonstrated differences in student perceptions based on giftedness. To explore the relationship between giftedness and students' perceptions of their learning environment, we examined students' perceptions of their laboratory learning environment in biology courses, including courses designated for high-achieving versus regular-achieving students. In addition, to explore the relationship between students' perceptions and the extent of their experience with laboratory learning in a particular discipline, we examined students' perceptions of their laboratory learning environment in first-year biology courses versus elective biology courses that require first-year biology as a prerequisite. We found that students in high-achieving courses had a more favourable perception of all aspects of their learning environment when compared with students in regular courses. In addition, student perceptions of their laboratory appeared to be influenced by the extent of their experience in learning science. Perceptions were consistent amongst regular- and high-achieving students regardless of grade level. In addition, perceptions of students in first year and beyond were consistent regardless of grade level. These findings have critical applications in curriculum development as well as in the classroom. Teachers can use student perceptions of their learning environment to emphasize critical pedagogical approaches and modify other areas that enable enhancement of the science laboratory learning environment.

  8. Factors influencing student perceptions of high-school science laboratory environments

    Science.gov (United States)

    Dolan, Erin L.

    2013-01-01

    Science laboratory learning has been lauded for decades for its role in fostering positive student attitudes about science and developing students’ interest in science and ability to use equipment. An expanding body of research has demonstrated the significant influence of laboratory environment on student learning. Further research has demonstrated differences in student perceptions based on giftedness. To explore the relationship between giftedness and students’ perceptions of their learning environment, we examined students’ perceptions of their laboratory learning environment in biology courses, including courses designated for high-achieving versus regular-achieving students. In addition, to explore the relationship between students’ perceptions and the extent of their experience with laboratory learning in a particular discipline, we examined students’ perceptions of their laboratory learning environment in first-year biology courses versus elective biology courses that require first-year biology as a prerequisite. We found that students in high-achieving courses had a more favourable perception of all aspects of their learning environment when compared with students in regular courses. In addition, student perceptions of their laboratory appeared to be influenced by the extent of their experience in learning science. Perceptions were consistent amongst regular- and high-achieving students regardless of grade level. In addition, perceptions of students in first year and beyond were consistent regardless of grade level. These findings have critical applications in curriculum development as well as in the classroom. Teachers can use student perceptions of their learning environment to emphasize critical pedagogical approaches and modify other areas that enable enhancement of the science laboratory learning environment. PMID:23950693

  9. Performance of fly ash concretes in accelerated and natural chloride exposure regimes

    Energy Technology Data Exchange (ETDEWEB)

    Sorn, V.; Oshiro, T.; Yamada, Y. [Ryukyus Univ., Okinawa (Japan). Dept. of Civil Engineering and Architecture; Sugiyama, T. [Gunma Univ. (Japan). Dept. of Civil Engineering; Matsufuji, Y. [Kyusyu Univ. (Japan). Dept. of Architecture

    2001-07-01

    Serious effort has been made in Japan to make use of the huge quantity of fly ash that is generated each year by coal-based thermal power plants. The produced fly ash contains unburned carbon, rendering it a low quality material classified as Japan Industrial Standard A 6201 class 3. The most efficient use of this kind of fly ash is to use it in concrete, where fly ash is added to the concrete without a corresponding reduction in the quantity of cement. A study was conducted to examine the penetrating characteristics of chloride ions into fly ash concrete and the corrosion of steel reinforcement in concrete, where portions of fine and coarse aggregates were replaced by fly ash. Compressive strength tests were conducted along with chloride penetration tests. Corrosion diagnosis of steel reinforcements was also performed. The physical properties and durability of fly ash concrete against aggressive environments was studied. It was determined that fly ash concretes have higher compressive strength than the control concrete. The strength development of fly ash concrete is very large, particularly on high-volume fly ash concretes. Chloride diffusion coefficients of fly ash concretes derived from the rapid chloride permeability test were found to decrease according to the volume of fly ash added. Chloride penetration of fly ash concretes also decreases with an increase in the volume of fly ash added. Corrosion diagnosis of steel reinforcement in concrete was shown to be effective for evaluating corrosive behaviour of steel reinforcement in fly ash concretes. The values of half-cell potential and polarization resistance measured on fly ash concretes become higher, suggesting no corrosion on steel reinforcement. 6 refs., 4 tabs., 10 figs.

  10. Characterization of the high-pressure structural transition and thermodynamic properties in sodium chloride: a computational investigation on the basis of the density functional theory.

    Science.gov (United States)

    Lu, Cheng; Kuang, Xiao-Yu; Zhu, Qin-Sheng

    2008-11-06

    Using first-principles calculations, the elastic constants, the thermodynamic properties, and the structural phase transition between the B1 (rocksalt) and the B2 (cesium chloride) phases of NaCl are investigated by means of the pseudopotential plane-waves method. The calculations are performed within the generalized gradient approximation to density functional theory with the Perdew-Burke-Ernzerhof exchange-correlation functional. On the basis of the third-order Birch-Murnaghan equation of states, the transition pressure Pt between the B1 phase and the B2 phase of NaCl is determined. The calculated values are generally speaking in good agreement with experiments and with similar theoretical calculations. From the theoretical calculations, the shear modulus, Young's modulus, rigidity modulus, and Poisson's ratio of NaCl are derived. According to the quasi-harmonic Debye model, we estimated the Debye temperature of NaCl from the average sound velocity. Moreover, the pressure derivatives of elastic constants, partial differentialC11/partial differentialP, partial differentialC12/partial differentialP, partial differentialC44/partial differentialP, partial differentialS11/partial differential P, partial differentialS12/partial differentialP, and partial differentialS44/partial differentialP, for NaCl crystal are investigated for the first time. This is a quantitative theoretical prediction of the elastic and thermodynamic properties of NaCl, and it still awaits experimental confirmation.

  11. Simultaneous analysis of apolar phytohormones and 1-aminocyclopropan-1-carboxylic acid by high performance liquid chromatography/electrospray negative ion tandem mass spectrometry via 9-fluorenylmethoxycarbonyl chloride derivatization.

    Science.gov (United States)

    Ziegler, Jörg; Qwegwer, Jakob; Schubert, Melvin; Erickson, Jessica L; Schattat, Martin; Bürstenbinder, Katharina; Grubb, C Douglas; Abel, Steffen

    2014-10-03

    A strategy to detect and quantify the polar ethylene precursor 1-aminocyclopropan-1-carboxylic acid (ACC) along with the more apolar phytohormones abscisic acid (ABA), indole-3-acetic acid (IAA), jasmonic acid (JA), jasmonic acid-isoleucine conjugate (JA-Ile), 12-oxo-phytodienoic acid (OPDA), trans-zeatin, and trans-zeatin 9-riboside using a single extraction is presented. Solid phase resins commonly employed for extraction of phytohormones do not allow the recovery of ACC. We circumvent this problem by attaching an apolar group to ACC via derivatization with the amino group specific reagent 9-fluorenylmethoxycarbonyl chloride (Fmoc-Cl). Derivatization in the methanolic crude extract does not modify other phytohormones. The derivatized ACC could be purified and detected together with the more apolar phytohormones using common solid phase extraction resins and reverse phase HPLC/electrospray negative ion tandem mass spectrometry. The limit of detection was in the low nanomolar range for all phytohormones, a sensitivity sufficient to accurately determine the phytohormone levels from less than 50mg (fresh weight) of Arabidopsis thaliana and Nicotiana benthamiana tissues. Comparison with previously published phytohormone levels and the reported changes in phytohormone levels after stress treatments confirmed the accuracy of the method.

  12. High-performance liquid chromatographic assay for catecholamines and metanephrines using fluorimetric detection with pre-column 9-fluorenylmethyloxycarbonyl chloride derivatization.

    Science.gov (United States)

    Chan, E C; Wee, P Y; Ho, P Y; Ho, P C

    2000-12-01

    A convenient HPLC-fluorescent assay of norepinephrine (NE), epinephrine (E), dopamine (DA) and their 3-O-methylated metabolites, normetanephrine (NM) and metanephrine (MN) was developed. These analytes were coupled to 9-fluorenylmethyloxycarbonyl chloride (FMOC-Cl) before assays. Results showed that using a linear gradient elution, peaks of FMOC-NE, FMOC-E, FMOC-DA, FMOC-NM, FMOC-MN and FMOC-DHBA (3,4-dihydroxybenzylamine, internal standard) were simultaneously resolved within 40 min. Optimization of the chromatographic and derivatization conditions, and validation of the assay were further discussed in the paper. The structures of these derivatives were confirmed by atmospheric pressure chemical ionization mass spectrometry (APCI-MS). The molecular ions [M+H]- of FMOC-NE, FMOC-E, FMOC-DA, FMOC-NM and FMOC-MN were m/z 836, 850, 820, 628 and 642, respectively. Based on these findings, the FMOC-derivatives of metanephrines and catecholamines were confirmed to be bi-substituted and tri-substituted respectively at the amino and catechol functional groups. Finally, the assay was successfully applied to the measurement of urinary E, DA, NM and MN after direct derivatization and simple cleaning.

  13. PRACTICAL ASPECTS FOR DEVELOPMENT OF INFORMATIONAL AND EDUCATIONAL ENVIRONMENT OF HIGH TECHNICAL SCHOOL

    Directory of Open Access Journals (Sweden)

    Sergey F. Rodionov

    2015-01-01

    Full Text Available The approach is offered to development of the informational and educational environment of high technical school,based on deep integration of electronic educational content with methods and tools for the engineering problemssolving. The application program interface (API is used asthe main integration instrument, which modern Its have.

  14. A harsh environment wireless pressure sensing solution utilizing high temperature electronics.

    Science.gov (United States)

    Yang, Jie

    2013-02-27

    Pressure measurement under harsh environments, especially at high temperatures, is of great interest to many industries. The applicability of current pressure sensing technologies in extreme environments is limited by the embedded electronics which cannot survive beyond 300 °C ambient temperature as of today. In this paper, a pressure signal processing and wireless transmission module based on the cutting-edge Silicon Carbide (SiC) devices is designed and developed, for a commercial piezoresistive MEMS pressure sensor from Kulite Semiconductor Products, Inc. Equipped with this advanced high-temperature SiC electronics, not only the sensor head, but the entire pressure sensor suite is capable of operating at 450 °C. The addition of wireless functionality also makes the pressure sensor more flexible in harsh environments by eliminating the costly and fragile cable connections. The proposed approach was verified through prototype fabrication and high temperature bench testing from room temperature up to 450 °C. This novel high-temperature pressure sensing technology can be applied in real-time health monitoring of many systems involving harsh environments, such as military and commercial turbine engines.

  15. Robust piezoelectric composites for energy harvesting in high-strain environments

    NARCIS (Netherlands)

    Ende, D.A. van der; Groen, W.A.; Zwaag, S. van der

    2013-01-01

    High-strain environments, such as are found in automobile tires, provide deformation energy that can be harvested using piezoelectric materials, for instance, for powering electronics such as wireless sensors. Despite numerous efforts, none of the present devices easily satisfy the stringent operati

  16. Quality Improvement, Inventory Management, Lead Time Reduction and Production Scheduling in High-Mix Manufacturing Environments

    Science.gov (United States)

    2017-01-13

    Quality Improvement, Inventory Management, Lead Time Reduction and Production Scheduling in High-mix Manufacturing Environments by Sean Daigle B.S...Mechanical Engineering Chairman, Department Committee on Graduate Theses 2 Quality Improvement, Inventory Management, Lead Time Reduction and...material shortage reduction and lead time reduction of system sub-assemblies. Man- ufacturing quality was found to be impacted by material shortages

  17. A Harsh Environment Wireless Pressure Sensing Solution Utilizing High Temperature Electronics

    Directory of Open Access Journals (Sweden)

    Jie Yang

    2013-02-01

    Full Text Available Pressure measurement under harsh environments, especially at high temperatures, is of great interest to many industries. The applicability of current pressure sensing technologies in extreme environments is limited by the embedded electronics which cannot survive beyond 300 °C ambient temperature as of today. In this paper, a pressure signal processing and wireless transmission module based on the cutting-edge Silicon Carbide (SiC devices is designed and developed, for a commercial piezoresistive MEMS pressure sensor from Kulite Semiconductor Products, Inc. Equipped with this advanced high-temperature SiC electronics, not only the sensor head, but the entire pressure sensor suite is capable of operating at 450 °C. The addition of wireless functionality also makes the pressure sensor more flexible in harsh environments by eliminating the costly and fragile cable connections. The proposed approach was verified through prototype fabrication and high temperature bench testing from room temperature up to 450 °C. This novel high-temperature pressure sensing technology can be applied in real-time health monitoring of many systems involving harsh environments, such as military and commercial turbine engines.

  18. Lesbian, Gay, Bisexual and Transgender Students: Perceived Social Support in the High School Environment

    Science.gov (United States)

    Munoz-Plaza, Corrine; Quinn, Sandra Crouse; Rounds, Kathleen A.

    2002-01-01

    Lesbian, gay, bisexual and transgender youth (LGBT) continue to face extreme discrimination within the school environment. Existing literature suggests that LGBT youth are at high risk for a number of health problems, including suicide ideation and attempts, harassment, substance abuse, homelessness, and declining school performance. This…

  19. Working with Gifted Science Students in a Public High School Environment: One School's Approach

    Science.gov (United States)

    Ngoi, Mephie; Vondracek, Mark

    2002-01-01

    The Chemistry/Physics Program at Evanston Township High School was designed to provide an environment for the rigorous teaching of advanced science and mathematics to accelerated students. This type of student makes up the bulk of students in the Advanced Placement Chemistry and Physics classes. However, there is a small number of students who…

  20. High Quality of the Environment HQE. The French Green Building approach

    Energy Technology Data Exchange (ETDEWEB)

    Sidoroff, S. (ed.)

    2001-07-01

    HQE (High Quality of the Environment) is a special and effective way to stimulate the market in environmental actions via a volunteer and certification scheme, accompanied by guidelines and everything needed to implement and activate the key issues. The HQE aims and activities are outlined by one of the initiators of the programme.

  1. Lesbian, Gay, Bisexual and Transgender Students: Perceived Social Support in the High School Environment

    Science.gov (United States)

    Munoz-Plaza, Corrine; Quinn, Sandra Crouse; Rounds, Kathleen A.

    2002-01-01

    Lesbian, gay, bisexual and transgender youth (LGBT) continue to face extreme discrimination within the school environment. Existing literature suggests that LGBT youth are at high risk for a number of health problems, including suicide ideation and attempts, harassment, substance abuse, homelessness, and declining school performance. This…

  2. The ionic product of water in concentrated tetramethylammonium chloride solutions.

    Science.gov (United States)

    Sipos, P; Bódi, I; May, P M; Hefter, G T

    1997-04-01

    The ionic product of water, pK(w) = - log[H(+)][OH(-)] has been determined in aqueous solutions of tetramethylammonium chloride over the concentration range of 0.1-5.5 M at 25 degrees C using high-precision glass electrode potentiometric titrations. pK(w) data relating to aqueous potassium and sodium chlorides at ionic strengths up to 5 M are markedly lower than the tetramethylammonium chloride results. These differences are almost certainly due to weak associations between potassium and (especially) sodium and hydroxide ions.

  3. Method for the production of uranium chloride salt

    Science.gov (United States)

    Westphal, Brian R.; Mariani, Robert D.

    2013-07-02

    A method for the production of UCl.sub.3 salt without the use of hazardous chemicals or multiple apparatuses for synthesis and purification is provided. Uranium metal is combined in a reaction vessel with a metal chloride and a eutectic salt- and heated to a first temperature under vacuum conditions to promote reaction of the uranium metal with the metal chloride for the production of a UCl.sub.3 salt. After the reaction has run substantially to completion, the furnace is heated to a second temperature under vacuum conditions. The second temperature is sufficiently high to selectively vaporize the chloride salts and distill them into a condenser region.

  4. Molten Triazolium Chloride Systems as New Aluminum Battery Electrolytes

    DEFF Research Database (Denmark)

    Vestergaard, B.; Bjerrum, Niels; Petrushina, Irina

    1993-01-01

    The possibility of using molten mixtures of 1,4-dimethyl-1,2,4-triazolium chloride (DMTC) and aluminum chloride (AlCl3) as secondary battery electrolytes was studied, in some cases extended by the copresence of sodium chloride. DMTC-AlCl, mixtures demonstrated high specific conductivity in a wide...... of milliamperes per square centimeter) was observed at 0.344 V on the acidic sodium tetrachloroaluminate background, involving a free triazolium radical mechanism. Molten DMTC-AlCl3 electrolytes are acceptable for battery performance and both the aluminum anode and the triazolium electrolyte can be used as active...

  5. High-resolution polypeptide structure and dynamics in anisotropic environments: The gramicidin channel

    Energy Technology Data Exchange (ETDEWEB)

    Cross, T.A.; Lee, K.C.; Ketchem, R.R.; Hu, W.; Lazo, N.D.; Huo, S. [Florida State Univ., Tallahassee, FL (United States)

    1994-12-01

    To understand the details of macromolecular function, high-resolution structural and dynamic detail is essential. The polypeptide fold of the gramicidin channel has been effectively modeled for the past 20 years, yet the functional changes in conductance and channel lifetime associated with amino acid substitutions cannot be predicted. To accomplish this goal, high-resolution electrostatic modeling and the precise orientation of all dipoles are required. Furthermore, an enhanced knowledge of the complex molecular environment of this membrane-bound peptide is needed. An aqueous environment is relatively uniform and achiral. The membrane environment is very heterogenous and chiral. A knowledge of the interactions, specific and nonspecific, between peptide and lipid will aid in developing a better understanding of this environment. To accomplish this goal, it is necessary to study the peptide in an extended lipid bilayer, rather than in a vesicular or micellar form. These latter environments are likely to possess increased dynamics, increased water penetration, and distorted interactions between the polypeptide and membrane surface. To perform NMR studies on bilayer bound peptides, solid state NMR methods are required, and for specific site information, isotopic labels are incorporated using solid phase peptide synthesis.

  6. The Influence of C3A Content in Cement on the Chloride Transport

    Directory of Open Access Journals (Sweden)

    Min Jae Kim

    2016-01-01

    Full Text Available The present study concerns the influence of C3A in cement on chloride transport in reinforced concrete. Three modified cement was manufactured in the variation of the C3A content, ranging from 6.0 and 10.5 up to 16.9%. The setting time of fresh concrete was measured immediately after mixing, together with the temperature at the time of initial set. For properties of hardened concrete in the variation in the C3A, a development of the compressive strength and chloride permeation were measured using mortar specimens. Simultaneously, chloride binding capacity was measured by the water extraction method. To ensure the influence of pore structure on chloride transport, the pore structure was examined by the mercury intrusion porosimetry. As a result, it was found that an increase in the C3A content resulted in an increase in chloride binding capacity. However, it seemed that increased binding of chlorides is related to the higher ingress of chlorides, despite denser pore structure. It may be attributed to the higher surface chloride, which could increase the gradient of chloride concentration from the surface, thereby leading to the higher level of chloride profiles. Substantially, the benefit of high C3A in resisting corrosion, arising from removal of free chlorides in the pore solution, would be offset by increased chloride ingress at a given duration, when it comes to the corrosion-free service life.

  7. Standard guide for corrosion tests in high temperature or high pressure environment, or both

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2010-01-01

    1.1 This guide covers procedures, specimens, and equipment for conducting laboratory corrosion tests on metallic materials under conditions of high pressure (HP) or the combination of high temperature and high pressure (HTHP). See for definitions of high pressure and temperature. 1.2 Tests conducted under HP or HTHP by their nature have special requirements. This guide establishes the basic considerations that are necessary when these conditions must be incorporated into laboratory corrosion tests. 1.3 The procedures and methods in this guide are applicable for conducting mass loss corrosion, localized corrosion, and electrochemical tests as well as for use in environmentally induced cracking tests that need to be conducted under HP or HTHP conditions. 1.4 The primary purpose for this guide is to promote consistency of corrosion test results. Furthermore, this guide will aid in the comparison of corrosion data between laboratories or testing organizations that utilize different equipment. 1.5 The values s...

  8. Computational Environments and Analysis methods available on the NCI High Performance Computing (HPC) and High Performance Data (HPD) Platform

    Science.gov (United States)

    Evans, B. J. K.; Foster, C.; Minchin, S. A.; Pugh, T.; Lewis, A.; Wyborn, L. A.; Evans, B. J.; Uhlherr, A.

    2014-12-01

    The National Computational Infrastructure (NCI) has established a powerful in-situ computational environment to enable both high performance computing and data-intensive science across a wide spectrum of national environmental data collections - in particular climate, observational data and geoscientific assets. This paper examines 1) the computational environments that supports the modelling and data processing pipelines, 2) the analysis environments and methods to support data analysis, and 3) the progress in addressing harmonisation of the underlying data collections for future transdisciplinary research that enable accurate climate projections. NCI makes available 10+ PB major data collections from both the government and research sectors based on six themes: 1) weather, climate, and earth system science model simulations, 2) marine and earth observations, 3) geosciences, 4) terrestrial ecosystems, 5) water and hydrology, and 6) astronomy, social and biosciences. Collectively they span the lithosphere, crust, biosphere, hydrosphere, troposphere, and stratosphere. The data is largely sourced from NCI's partners (which include the custodians of many of the national scientific records), major research communities, and collaborating overseas organisations. The data is accessible within an integrated HPC-HPD environment - a 1.2 PFlop supercomputer (Raijin), a HPC class 3000 core OpenStack cloud system and several highly connected large scale and high-bandwidth Lustre filesystems. This computational environment supports a catalogue of integrated reusable software and workflows from earth system and ecosystem modelling, weather research, satellite and other observed data processing and analysis. To enable transdisciplinary research on this scale, data needs to be harmonised so that researchers can readily apply techniques and software across the corpus of data available and not be constrained to work within artificial disciplinary boundaries. Future challenges will

  9. Performance measurement and modeling of component applications in a high performance computing environment : a case study.

    Energy Technology Data Exchange (ETDEWEB)

    Armstrong, Robert C.; Ray, Jaideep; Malony, A. (University of Oregon, Eugene, OR); Shende, Sameer (University of Oregon, Eugene, OR); Trebon, Nicholas D.

    2003-11-01

    We present a case study of performance measurement and modeling of a CCA (Common Component Architecture) component-based application in a high performance computing environment. We explore issues peculiar to component-based HPC applications and propose a performance measurement infrastructure for HPC based loosely on recent work done for Grid environments. A prototypical implementation of the infrastructure is used to collect data for a three components in a scientific application and construct performance models for two of them. Both computational and message-passing performance are addressed.

  10. Effects of external environment on thermocapillary convection of high prandtl number fluid

    Directory of Open Access Journals (Sweden)

    Liang Ruquan

    2016-01-01

    Full Text Available Numerical simulations have been carried out to investigate the influence of external environment on thermocapillary convection in high Prandtl number (Pr=68 liquid. The geometric model of physical problem is that the the liquid bridge surrounded by ambient air under zero or ground gravity. The interface velocity, temperature, heat flux and flow pattern in the liquid bridge are presented and discussed under different conditions by changing the external environment. The buoyancy convection produces a symmetrical vortex in the liquid bridge. The ambient air affects the distributions of the temperature velocity and heat flux on the interface by changing the thermocapillary convection.

  11. A novel capsule-based selfrecovery system with a chloride ion trigger

    NARCIS (Netherlands)

    Xiong, W.; Tang, J.; Zhu, G.; Han, N.; Schlangen, E.; Dong, B.; Wang, X.; Xing, F.

    2015-01-01

    Steel is prone to corrosion induced by chloride ions, which is a serious threat to reinforced concrete structures, especially in marine environments. In this work, we report a novel capsule-based selfrecovery system that utilizes chloride ions as a trigger. These capsules, which are functionalized

  12. A novel capsule-based selfrecovery system with a chloride ion trigger

    NARCIS (Netherlands)

    Xiong, W.; Tang, J.; Zhu, G.; Han, N.; Schlangen, E.; Dong, B.; Wang, X.; Xing, F.

    2015-01-01

    Steel is prone to corrosion induced by chloride ions, which is a serious threat to reinforced concrete structures, especially in marine environments. In this work, we report a novel capsule-based selfrecovery system that utilizes chloride ions as a trigger. These capsules, which are functionalized v

  13. The effect of bonding environment on iron isotope fractionation between minerals at high temperature

    Science.gov (United States)

    Sossi, Paolo A.; O'Neill, Hugh St. C.

    2017-01-01

    Central to understanding the processes that drive stable isotope fractionation in nature is their quantification under controlled experimental conditions. The polyvalent element iron, given its abundance in terrestrial rocks, exerts controls on the structural and chemical properties of minerals and melts. The iron isotope compositions of typical high temperature minerals are, however, poorly constrained and their dependence on intensive (e.g. fO2) and extensive (e.g. compositional) variables is unknown. In this work, experiments involving a reference phase, 2 M FeCl2·4H2O(l), together with an oxide mix corresponding to the bulk composition of the chosen mineral were performed in a piston cylinder in Ag capsules. The oxide mix crystallised in situ at 1073 K and 1 GPa, in equilibrium with the iron chloride, and was held for 72 h. In order to characterise the effect of co-ordination and oxidation state on the isotope composition independently, exclusively Fe2+ minerals were substituted in: VIII-fold almandine, VI-fold ilmenite, fayalite and IV-fold chromite and hercynite. Δ57FeMin-FeCl2 increases in the order VIII ion. The composition of the VIFe2+-bearing minerals is similar to that of the aqueous FeCl2 fluid. To the degree that this represents the speciation of iron in fluids exsolving from magmas, the fractionation between them should be small, unless the iron is hosted in magnetite. By contrast, predominantly Fe2+-bearing mantle garnets should preserve a much lighter δ57Fe than their lower pressure spinel counterparts, a signature that may be reflected in partial melts from these lithologies. As the Fe-O bond lengths in fayalite and ilmenite are comparable, their isotope compositions overlap, suggesting that high Ti mare basalts acquired their heavy isotopic signature from ilmenite that crystallised late during lunar magma ocean solidification.

  14. Studies Update Vinyl Chloride Hazards.

    Science.gov (United States)

    Rawls, Rebecca

    1980-01-01

    Extensive study affirms that vinyl chloride is a potent animal carcinogen. Epidemiological studies show elevated rates of human cancers in association with extended contact with the compound. (Author/RE)

  15. High Performance Processors for Space Environments: A Subproject of the NASA Exploration Missions Systems Directorate "Radiation Hardened Electronics for Space Environments" Technology Development Program

    Science.gov (United States)

    Johnson, M.; Label, K.; McCabe, J.; Powell, W.; Bolotin, G.; Kolawa, E.; Ng, T.; Hyde, D.

    2007-01-01

    Implementation of challenging Exploration Systems Missions Directorate objectives and strategies can be constrained by onboard computing capabilities and power efficiencies. The Radiation Hardened Electronics for Space Environments (RHESE) High Performance Processors for Space Environments project will address this challenge by significantly advancing the sustained throughput and processing efficiency of high-per$ormance radiation-hardened processors, targeting delivery of products by the end of FY12.

  16. Star Formation in High Pressure, High Energy Density Environments: Laboratory Experiments of ISM Dust Analogs

    Energy Technology Data Exchange (ETDEWEB)

    van Breugel, W; Bajt, S; Bradley, J; Bringa, E; Dai, Z; Felter, T; Graham, G; Kucheyev, S; Torres, D; Tielens, A; Baragiola, R; Dukes, C; Loeffler, M

    2005-01-05

    Dust grains control the chemistry and cooling, and thus the gravitational collapse of interstellar clouds. Energetic particles, shocks and ionizing radiation can have a profound influence on the structure, lifetime and chemical reactivity of the dust, and therefore on the star formation efficiency. This would be especially important in forming galaxies, which exhibit powerful starburst (supernovae) and AGN (active galactic nucleus) activity. How dust properties are affected in such environments may be crucial for a proper understanding of galaxy formation and evolution. The authors present the results of experiments at LLNL which show that irradiation of the interstellar medium (ISM) dust analog forsterite (Mg{sub 2}SiO{sub 4}) with swift heavy ions (10 MeV Xe) and a large electronic energy deposition amorphizes its crystalline structure, without changing its chemical composition. From the data they predict that silicate grains in the ISM, even in dense and cold giant molecular clouds, can be amorphized by heavy cosmic rays (CR's). This might provide an explanation for the observed absence of crystalline dust in the ISM clouds of the Milky Way galaxy. This processing of dust by CR's would be even more important in forming galaxies and galaxies with active black holes.

  17. Chloride ingress profiles measured by electron probe micro analysis

    DEFF Research Database (Denmark)

    Jensen, Ole mejlhede; Coats, Alison M.; Glasser, Fred P.

    1996-01-01

    Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA is demonst......Traditional techniques for measuring chloride ingress profiles do not apply well to high performance cement paste systems; the geometric resolution of the traditional measuring techniques is too low. In this paper measurements by Electron Probe Micro Analysis (EPMA) are presented. EPMA...... is demonstated to determine chloride ingress in cement paste on a micrometer scale. Potential chloride ingress routes such as cracks or the paste-aggregate interface may also be characterized by EPMA. Copyright (C) 1996 Elsevier Science Ltd...

  18. Parameters Affecting Hydrogen Chloride Measurements

    Science.gov (United States)

    1993-06-01

    contain sea salt, which is hygroscopic because of the magnesium chloride present, or ammonium bisulfate , which mostly comes from sulfur pollution and is...boosters release hydrogen chloride as a combustion product, and hydrazines or nitric acid can be spilled from liquid fuel motors. Monitoring the...solubility constant, and the second is the acid ionization constant. From experimental work, the product of the two constants is well established (Reference

  19. Astroglial pentose phosphate pathway rates in response to high-glucose environments

    Directory of Open Access Journals (Sweden)

    Norihiro Suzuki

    2012-03-01

    Full Text Available ROS (reactive oxygen species play an essential role in the pathophysiology of diabetes, stroke and neurodegenerative disorders. Hyperglycaemia associated with diabetes enhances ROS production and causes oxidative stress in vascular endothelial cells, but adverse effects of either acute or chronic high-glucose environments on brain parenchymal cells remain unclear. The PPP (pentose phosphate pathway and GSH participate in a major defence mechanism against ROS in brain, and we explored the role and regulation of the astroglial PPP in response to acute and chronic high-glucose environments. PPP activity was measured in cultured neurons and astroglia by determining the difference in rate of 14CO2 production from [1-14C]glucose and [6-14C]glucose. ROS production, mainly H2O2, and GSH were also assessed. Acutely elevated glucose concentrations in the culture media increased PPP activity and GSH level in astroglia, decreasing ROS production. Chronically elevated glucose environments also induced PPP activation. Immunohistochemical analyses revealed that chronic high-glucose environments induced ER (endoplasmic reticulum stress (presumably through increased hexosamine biosynthetic pathway flux. Nuclear translocation of Nrf2 (nuclear factor-erythroid 2 p45 subunit-related factor 2, which regulates G6PDH (glyceraldehyde-6-phosphate dehydrogenase by enhancing transcription, was also observed in association with BiP (immunoglobulin heavy-chain-binding protein expression. Acute and chronic high-glucose environments activated the PPP in astroglia, preventing ROS elevation. Therefore a rapid decrease in glucose level seems to enhance ROS toxicity, perhaps contributing to neural damage when insulin levels given to diabetic patients are not properly calibrated and plasma glucose levels are not adequately maintained. These findings may also explain the lack of evidence for clinical benefits from strict glycaemic control during the acute phase of stroke.

  20. Astroglial Pentose Phosphate Pathway Rates in Response to High-Glucose Environments

    Directory of Open Access Journals (Sweden)

    Shinichi Takahashi

    2012-02-01

    Full Text Available ROS (reactive oxygen species play an essential role in the pathophysiology of diabetes, stroke and neurodegenerative disorders. Hyperglycaemia associated with diabetes enhances ROS production and causes oxidative stress in vascular endothelial cells, but adverse effects of either acute or chronic high-glucose environments on brain parenchymal cells remain unclear. The PPP (pentose phosphate pathway and GSH participate in a major defence mechanism against ROS in brain, and we explored the role and regulation of the astroglial PPP in response to acute and chronic high-glucose environments. PPP activity was measured in cultured neurons and astroglia by determining the difference in rate of 14CO2 production from [1-14C]glucose and [6-14C]glucose. ROS production, mainly H2O2, and GSH were also assessed. Acutely elevated glucose concentrations in the culture media increased PPP activity and GSH level in astroglia, decreasing ROS production. Chronically elevated glucose environments also induced PPP activation. Immunohistochemical analyses revealed that chronic high-glucose environments induced ER (endoplasmic reticulum stress (presumably through increased hexosamine biosynthetic pathway flux. Nuclear translocation of Nrf2 (nuclear factor-erythroid 2 p45 subunit-related factor 2, which regulates G6PDH (glyceraldehyde-6-phosphate dehydrogenase by enhancing transcription, was also observed in association with BiP (immunoglobulin heavy-chain-binding protein expression. Acute and chronic high-glucose environments activated the PPP in astroglia, preventing ROS elevation. Therefore a rapid decrease in glucose level seems to enhance ROS toxicity, perhaps contributing to neural damage when insulin levels given to diabetic patients are not properly calibrated and plasma glucose levels are not adequately maintained. These findings may also explain the lack of evidence for clinical benefits from strict glycaemic control during the acute phase of stroke.

  1. Silicon-Carbide Power MOSFET Performance in High Efficiency Boost Power Processing Unit for Extreme Environments

    Science.gov (United States)

    Ikpe, Stanley A.; Lauenstein, Jean-Marie; Carr, Gregory A.; Hunter, Don; Ludwig, Lawrence L.; Wood, William; Del Castillo, Linda Y.; Fitzpatrick, Fred; Chen, Yuan

    2016-01-01

    Silicon-Carbide device technology has generated much interest in recent years. With superior thermal performance, power ratings and potential switching frequencies over its Silicon counterpart, Silicon-Carbide offers a greater possibility for high powered switching applications in extreme environment. In particular, Silicon-Carbide Metal-Oxide- Semiconductor Field-Effect Transistors' (MOSFETs) maturing process technology has produced a plethora of commercially available power dense, low on-state resistance devices capable of switching at high frequencies. A novel hard-switched power processing unit (PPU) is implemented utilizing Silicon-Carbide power devices. Accelerated life data is captured and assessed in conjunction with a damage accumulation model of gate oxide and drain-source junction lifetime to evaluate potential system performance at high temperature environments.

  2. Effect of realgar on extracellular amino acid neurotransmitters in hippocampal CA1 region determined by online microdialysis–dansyl chloride derivatization–high-performance liquid chromatography and fluorescence detection.

    Science.gov (United States)

    Huo, Taoguang; Zhang, Yinghua; Li, Weikai; Yang, Huilei; Jiang, Hong; Sun, Guifan

    2014-09-01

    An online microdialysis (MD)–dansyl chloride (Dns) derivatization–high-performance liquid chromatography (HPLC) and fluorescence detection (FD) system was developed for simultaneous determination of eight extracellular amino acid neurotransmitters in hippocampus. The MD probe was implanted in hippocampal CA1 region. Dialysate and Dns were online mixed and derivatized. The derivatives were separated on an ODS column and detected by FD. The developed online system showed good linearity, precision, accuracy and recovery. This online MD-HPLC system was applied to monitor amino acid neurotransmitters levels in rats exposed to realgar (0.3, 0.9 and 2.7 g/kg body weight). The result shows that glutamate concentrations were significantly increased (pHPLC–FD system provides a new experimental method for studying the effect of toxic Chinese medicines on amino acid neurotransmitters.

  3. Determination of the unusual amino acid hypusine at the lower picomole level by derivatization with 4-dimethylaminoazobenzene-4'-sulphonyl chloride and reversed-phase high-performance or medium-pressure liquid chromatography.

    Science.gov (United States)

    Bartig, D; Klink, F

    1992-07-31

    Hypusine, an unusual amino acid formed by post-translational modification of lysine, is normally determined by specific metabolic labelling followed by measurement of released radioactivity after protein hydrolysis. This paper describes a sensitive non-radioactive method for the determination of hypusine, involving complete protein hydrolysis and precolumn derivatization of the released amino acids with 4-dimethylaminoazobenzene-4'-sulphonyl chloride, followed by reversed-phase high-performance or medium-pressure liquid chromatography of the dabsylated derivatives. The detection limit of hypusine was about 500 fmol. Additionally, the hypusine-containing protein from the archaebacterium Sulfolobus acidocaldarius was purified. By applying the dabsylation method to the analysis of tryptic peptides derived from this protein, it was possible to determine the correct positioning of the hypusine residue in the amino acid sequence, which was not possible by the amino acid sequencing procedure alone.

  4. Crowd Behaviour during High-Stress Evacuations in an Immersive Virtual Environment

    CERN Document Server

    Moussaïd, Mehdi; Thrash, Tyler; Sumner, Robert W; Gross, Markus; Helbing, Dirk; Hölscher, Christoph

    2016-01-01

    Understanding the collective dynamics of crowd movements during stressful emergency situations is central to reducing the risk of deadly crowd disasters. Yet, their systematic experimental study remains a challenging open problem due to ethical and methodological constraints. In this paper, we demonstrate the viability of shared 3D virtual environments as an experimental platform for conducting crowd experiments with real people. In particular, we show that crowds of real human subjects moving and interacting in an immersive 3D virtual environment exhibit typical patterns of real crowds as observed in real-life crowded situations. These include the manifestation of social conventions and the emergence of self-organized patterns during egress scenarios. High-stress evacuation experiments conducted in this virtual environment reveal movements characterized by mass herding and dangerous overcrowding as they occur in crowd disasters. We describe the behavioral mechanisms at play under such extreme conditions and ...

  5. Secure Enclaves: An Isolation-centric Approach for Creating Secure High Performance Computing Environments

    Energy Technology Data Exchange (ETDEWEB)

    Aderholdt, Ferrol [Tennessee Technological Univ., Cookeville, TN (United States); Caldwell, Blake A. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hicks, Susan Elaine [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Koch, Scott M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Naughton, III, Thomas J. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pelfrey, Daniel S. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pogge, James R [Tennessee Technological Univ., Cookeville, TN (United States); Scott, Stephen L [Tennessee Technological Univ., Cookeville, TN (United States); Shipman, Galen M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sorrillo, Lawrence [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-01-01

    High performance computing environments are often used for a wide variety of workloads ranging from simulation, data transformation and analysis, and complex workflows to name just a few. These systems may process data at various security levels but in so doing are often enclaved at the highest security posture. This approach places significant restrictions on the users of the system even when processing data at a lower security level and exposes data at higher levels of confidentiality to a much broader population than otherwise necessary. The traditional approach of isolation, while effective in establishing security enclaves poses significant challenges for the use of shared infrastructure in HPC environments. This report details current state-of-the-art in virtualization, reconfigurable network enclaving via Software Defined Networking (SDN), and storage architectures and bridging techniques for creating secure enclaves in HPC environments.

  6. Chloride channels in stroke

    Institute of Scientific and Technical Information of China (English)

    Ya-ping ZHANG; Hao ZHANG; Dayue Darrel DUAN

    2013-01-01

    Vascular remodeling of cerebral arterioles,including proliferation,migration,and apoptosis of vascular smooth muscle cells (VSMCs),is the major cause of changes in the cross-sectional area and diameter of the arteries and sudden interruption of blood flow or hemorrhage in the brain,ie,stroke.Accumulating evidence strongly supports an important role for chloride (Clˉ) channels in vascular remodeling and stroke.At least three Clˉ channel genes are expressed in VSMCs:1) the TMEM16A (or Ano1),which may encode the calcium-activated Clˉ channels (CACCs); 2) the CLC-3 Clˉ channel and Clˉ/H+ antiporter,which is closely related to the volume-regulated Clˉ channels (VRCCs); and 3) the cystic fibrosis transmembrane conductance regulator (CFTR),which encodes the PKA-and PKC-activated Clˉ channels.Activation of the CACCs by agonist-induced increase in intracellular Ca2+ causes membrane depolarization,vasoconstriction,and inhibition of VSMC proliferation.Activation of VRCCs by cell volume increase or membrane stretch promotes the production of reactive oxygen species,induces proliferation and inhibits apoptosis of VSMCs.Activation of CFTR inhibits oxidative stress and may prevent the development of hypertension.In addition,Clˉ current mediated by gammaaminobutyric acid (GABA) receptor has also been implicated a role in ischemic neuron death.This review focuses on the functional roles of Clˉ channels in the development of stroke and provides a perspective on the future directions for research and the potential to develop Clˉ channels as new targets for the prevention and treatment of stroke.

  7. Involvement of Coat Proteins in Bacillus subtilis Spore Germination in High-Salinity Environments.

    Science.gov (United States)

    Nagler, Katja; Setlow, Peter; Reineke, Kai; Driks, Adam; Moeller, Ralf

    2015-10-01

    The germination of spore-forming bacteria in high-salinity environments is of applied interest for food microbiology and soil ecology. It has previously been shown that high salt concentrations detrimentally affect Bacillus subtilis spore germination, rendering this process slower and less efficient. The mechanistic details of these salt effects, however, remained obscure. Since initiation of nutrient germination first requires germinant passage through the spores' protective integuments, the aim of this study was to elucidate the role of the proteinaceous spore coat in germination in high-salinity environments. Spores lacking major layers of the coat due to chemical decoating or mutation germinated much worse in the presence of NaCl than untreated wild-type spores at comparable salinities. However, the absence of the crust, the absence of some individual nonmorphogenetic proteins, and the absence of either CwlJ or SleB had no or little effect on germination in high-salinity environments. Although the germination of spores lacking GerP (which is assumed to facilitate germinant flow through the coat) was generally less efficient than the germination of wild-type spores, the presence of up to 2.4 M NaCl enhanced the germination of these mutant spores. Interestingly, nutrient-independent germination by high pressure was also inhibited by NaCl. Taken together, these results suggest that (i) the coat has a protective function during germination in high-salinity environments; (ii) germination inhibition by NaCl is probably not exerted at the level of cortex hydrolysis, germinant accessibility, or germinant-receptor binding; and (iii) the most likely germination processes to be inhibited by NaCl are ion, Ca(2+)-dipicolinic acid, and water fluxes.

  8. Interactions between chloride and cement-paste materials.

    Science.gov (United States)

    Barberon, Fabien; Baroghel-Bouny, Véronique; Zanni, Hélène; Bresson, Bruno; d'Espinose de la Caillerie, Jean-Baptiste; Malosse, Lucie; Gan, Zehong

    2005-02-01

    The durability of cement-based materials with respect to exterior aggressions is one of the current priorities in civil engineering. Depending on their use, the cement-based materials can be exposed to different types of aggressive environments. For instance, damages to concrete structures in contact with a saline environment (sea water on bridges, deicing salts on roads, etc.) are of utmost importance. Upon exposure to saline water, Cl- ions penetrate into the structures and subsequently lead to reinforcement corrosion. Chloride attack is often combined with other aggressive influences such as temperature (e.g., freezing) or the ingress of other ions (e.g., sulfates in sea water). We therefore aim to explore the effect of sodium chloride (NaCl) on the structural chemistry of cement paste. Existing studies about reinforcement corrosion by chloride have focused on the penetration of Cl- ions and the comparison between "free" ions (water-soluble ions) and bound ones. However, little is known about the fixation mechanisms, the localization of Cl in the cement matrix and the structural interaction between Cl and the silicate and aluminate hydrate phases present in cement paste. We present here results of a multinuclear nuclear magnetic resonance study on the fixation of chloride in the hydration products and the characterization of new phases potentially appearing due to chloride ingress.

  9. 21 CFR 184.1138 - Ammonium chloride.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ammonium chloride. 184.1138 Section 184.1138 Food... Specific Substances Affirmed as GRAS § 184.1138 Ammonium chloride. (a) Ammonium chloride (NH4Cl, CAS Reg. No. 12125-02-9) is produced by the reaction of sodium chloride and an ammonium salt in solution....

  10. The High-Metallicity Explosion Environment of the Relativistic Supernova 2009bb

    CERN Document Server

    Levesque, E M; Foley, R J; Berger, E; Kewley, L J; Chakraborty, S; Ray, A; Torres, M A P; Challis, P; Kirshner, R P; Barthelmy, S D; Bietenholz, M F; Chandra, P; Chaplin, V; Chevalier, R A; Chugai, N; Connaughton, V; Copete, A; Fox, O; Fransson, C; Grindlay, J E; Hamuy, M A; Milne, P A; Pignata, G; Stritzinger, M D; Wieringa, M H

    2009-01-01

    We investigate the environment of the nearby (d ~ 40Mpc) broad-lined Type Ic supernova SN 2009bb. This event was observed to produce a relativistic outflow likely powered by a central accreting compact object. While such a phenomenon was previously observed only in long-duration gamma-ray bursts (LGRBs), no LGRB was detected in association with SN 2009bb. Using an optical spectrum of the SN 2009bb explosion site, we determine a variety of ISM properties for the host environment, including metallicity, young stellar population age, and star formation rate. We compare the SN explosion site properties to observations of LGRB and broad-lined SN Ic host environments on optical emission line ratio diagnostic diagrams. Based on these analyses, we find that the SN 2009bb explosion site has a very high metallicity of ~2x solar, in agreement with other broad-lined SN Ic host environments and at odds with the low-redshift LGRB host environments and recently proposed maximum metallicity limits for relativistic explosions...

  11. Computational modelling of chloride ion transport in reinforced concrete

    NARCIS (Netherlands)

    Meijers, S.J.H.; Bijen, J.M.J.M.; De Borst, R.; Fraaij, A.L.A.

    2001-01-01

    Exposure to a saline environment is a major threat with respect to the durability of reinforced concrete structures. The chloride ions, which are present in seawater and de-icing salts, are able to penetrate the concrete up to the depth of the reinforcement. They can eventually trigger a pitting cor

  12. Calcium/thionyl chloride battery technology

    Science.gov (United States)

    Counts, T.

    1985-12-01

    This final report documents the development efforts conducted by the Lithium Batteries Group of the Couples Department of Eagle-Picher Industries. The objective of the project was to develop calcium-thionyl chloride cell technology. The original project was divided into two main tasks. Task One was to consist of component optimization and stability studies. Once sufficiently advanced, the ongoing results of Task One were to be integrated with Task Two. Task Two was to consist of demonstration of an optimized primary cell. In July, 1983, the program was redirected. Task Two was split, with effort to be directed toward both the original primary cell and toward a high discharge rate reserve configuration cell. Additional electrolyte salts were to be evaluated as a means of improving the storability of the active calcium-thionyl chloride cell.

  13. Impact of a Combined High Cholesterol Diet and High Glucose Environment on Vasculature

    Science.gov (United States)

    Cui, Taixing; Tang, Dongqi; Wang, Xing Li

    2013-01-01

    Aims Vascular complications are the leading cause of mortality and morbidity in patients with diabetes. However, proper animal models of diabetic vasculopathy that recapitulate the accelerated progression of vascular lesions in human are unavailable. In the present study, we developed a zebrafish model of diabetic vascular complications and the methodology for quantifying vascular lesion formation real-time in the living diabetic zebrafish. Methods and Results Wild type zebrafish (AB) and transgenic zebrafish lines of fli1:EGFP, lyz:EGFP, gata1:dsRed, double transgenic zebrafish of gata1:dsRed/fli1:EGFP were exposed to high cholesterol diet and 3% glucose (HCD-HG) for 10 days. The zebrafish model with HCD-HG treatment was characterized by significantly increased tissue levels of insulin, glucagon, glucose, total triglyceride and cholesterol. Confocal microscopic analysis further revealed that the diabetic larvae developed clearly thickened endothelial layers, distinct perivascular lipid depositions, substantial accumulations of inflammatory cells in the injured vasculature, and a decreased velocity of blood flow. Moreover, the vascular abnormalities were improved by the treatment of pioglitazone and metformin. Conclusion A combination of high cholesterol diet and high glucose exposure induces a rapid onset of vascular complications in zebrafish similar to the early atherosclerotic vascular injuries in mammalian diabetic models, suggesting that zebrafish may be used as a novel animal model for diabetic vasculopathy. PMID:24349075

  14. The fate of high redshift massive compact galaxies in dense environments

    Energy Technology Data Exchange (ETDEWEB)

    Kaufmann, Tobias; /Zurich, ETH; Mayer, Lucio; /Zurich U.; Carollo, Marcella; /Zurich, ETH; Feldmann, Robert; /Fermilab /Chicago U., KICP

    2012-01-01

    Massive compact galaxies seem to be more common at high redshift than in the local universe, especially in denser environments. To investigate the fate of such massive galaxies identified at z {approx} 2 we analyse the evolution of their properties in three cosmological hydrodynamical simulations that form virialized galaxy groups of mass {approx} 10{sup 13} M{sub {circle_dot}} hosting a central massive elliptical/S0 galaxy by redshift zero. We find that at redshift {approx} 2 the population of galaxies with M{sub *} > 2 x 10{sup 10} M{sub {circle_dot}} is diverse in terms of mass, velocity dispersion, star formation and effective radius, containing both very compact and relatively extended objects. In each simulation all the compact satellite galaxies have merged into the central galaxy by redshift 0 (with the exception of one simulation where one of such satellite galaxy survives). Satellites of similar mass at z = 0 are all less compact than their high redshift counterparts. They form later than the galaxies in the z = 2 sample and enter the group potential at z < 1, when dynamical friction times are longer than the Hubble time. Also, by z = 0 the central galaxies have increased substantially their characteristic radius via a combination of in situ star formation and mergers. Hence in a group environment descendants of compact galaxies either evolve towards larger sizes or they disappear before the present time as a result of the environment in which they evolve. Since the group-sized halos that we consider are representative of dense environments in the {Lambda}CDM cosmology, we conclude that the majority of high redshift compact massive galaxies do not survive until today as a result of the environment.

  15. Crowd behaviour during high-stress evacuations in an immersive virtual environment

    Science.gov (United States)

    Kapadia, Mubbasir; Thrash, Tyler; Sumner, Robert W.; Gross, Markus; Helbing, Dirk; Hölscher, Christoph

    2016-01-01

    Understanding the collective dynamics of crowd movements during stressful emergency situations is central to reducing the risk of deadly crowd disasters. Yet, their systematic experimental study remains a challenging open problem due to ethical and methodological constraints. In this paper, we demonstrate the viability of shared three-dimensional virtual environments as an experimental platform for conducting crowd experiments with real people. In particular, we show that crowds of real human subjects moving and interacting in an immersive three-dimensional virtual environment exhibit typical patterns of real crowds as observed in real-life crowded situations. These include the manifestation of social conventions and the emergence of self-organized patterns during egress scenarios. High-stress evacuation experiments conducted in this virtual environment reveal movements characterized by mass herding and dangerous overcrowding as they occur in crowd disasters. We describe the behavioural mechanisms at play under such extreme conditions and identify critical zones where overcrowding may occur. Furthermore, we show that herding spontaneously emerges from a density effect without the need to assume an increase of the individual tendency to imitate peers. Our experiments reveal the promise of immersive virtual environments as an ethical, cost-efficient, yet accurate platform for exploring crowd behaviour in high-risk situations with real human subjects. PMID:27605166

  16. Characterizing the Chemical Stability of High Temperature Materials for Application in Extreme Environments

    Science.gov (United States)

    Opila, Elizabeth

    2005-01-01

    The chemical stability of high temperature materials must be known for use in the extreme environments of combustion applications. The characterization techniques available at NASA Glenn Research Center vary from fundamental thermodynamic property determination to material durability testing in actual engine environments. In this paper some of the unique techniques and facilities available at NASA Glenn will be reviewed. Multiple cell Knudsen effusion mass spectrometry is used to determine thermodynamic data by sampling gas species formed by reaction or equilibration in a Knudsen cell held in a vacuum. The transpiration technique can also be used to determine thermodynamic data of volatile species but at atmospheric pressures. Thermodynamic data in the Si-O-H(g) system were determined with this technique. Free Jet Sampling Mass Spectrometry can be used to study gas-solid interactions at a pressure of one atmosphere. Volatile Si(OH)4(g) was identified by this mass spectrometry technique. A High Pressure Burner Rig is used to expose high temperature materials in hydrocarbon-fueled combustion environments. Silicon carbide (SiC) volatility rates were measured in the burner rig as a function of total pressure, gas velocity and temperature. Finally, the Research Combustion Lab Rocket Test Cell is used to expose high temperature materials in hydrogen/oxygen rocket engine environments to assess material durability. SiC recession due to rocket engine exposures was measured as a function of oxidant/fuel ratio, temperature, and total pressure. The emphasis of the discussion for all techniques will be placed on experimental factors that must be controlled for accurate acquisition of results and reliable prediction of high temperature material chemical stability.

  17. TURBULENCE SETS THE INITIAL CONDITIONS FOR STAR FORMATION IN HIGH-PRESSURE ENVIRONMENTS

    Energy Technology Data Exchange (ETDEWEB)

    Rathborne, J. M.; Contreras, Y. [CSIRO Astronomy and Space Science, P.O. Box 76, Epping NSW, 1710 (Australia); Longmore, S. N.; Bastian, N. [Astrophysics Research Institute, Liverpool John Moores University, 146 Brownlow Hill, Liverpool L3 5RF (United Kingdom); Jackson, J. M. [Institute for Astrophysical Research, Boston University, Boston, MA 02215 (United States); Kruijssen, J. M. D. [Max-Planck Institut fur Astrophysik, Karl-Schwarzschild-Strasse 1, D-85748, Garching (Germany); Alves, J. F. [University of Vienna, Türkenschanzstrasse 17, A-1180 Vienna (Austria); Bally, J. [Center for Astrophysics and Space Astronomy, University of Colorado, UCB 389, Boulder, CO 8030 (United States); Foster, J. B. [Department of Astronomy, Yale University, P.O. Box 208101 New Haven, CT 06520-8101 (United States); Garay, G. [Universidad de Chile, Camino El Observatorio1515, Las Condes, Santiago (Chile); Testi, L. [European Southern Observatory, Karl-Schwarzschild-Strasse 2, D-85748 Garching bei Munchen (Germany); Walsh, A. J., E-mail: Jill.Rathborne@csiro.au [International Centre for Radio Astronomy Research, Curtin University, GPO Box U1987, Perth (Australia)

    2014-11-10

    Despite the simplicity of theoretical models of supersonically turbulent, isothermal media, their predictions successfully match the observed gas structure and star formation activity within low-pressure (P/k < 10{sup 5} K cm{sup –3}) molecular clouds in the solar neighborhood. However, it is unknown whether or not these theories extend to clouds in high-pressure (P/k > 10{sup 7} K cm{sup –3}) environments, like those in the Galaxy's inner 200 pc central molecular zone (CMZ) and in the early universe. Here, we present Atacama Large Millimeter/submillimeter Array 3 mm dust continuum emission within a cloud, G0.253+0.016, which is immersed in the high-pressure environment of the CMZ. While the log-normal shape and dispersion of its column density probability distribution function (PDF) are strikingly similar to those of solar neighborhood clouds, there is one important quantitative difference: its mean column density is one to two orders of magnitude higher. Both the similarity and difference in the PDF compared to those derived from solar neighborhood clouds match predictions of turbulent cloud models given the high-pressure environment of the CMZ. The PDF shows a small deviation from log-normal at high column densities confirming the youth of G0.253+0.016. Its lack of star formation is consistent with the theoretically predicted, environmentally dependent volume density threshold for star formation which is orders of magnitude higher than that derived for solar neighborhood clouds. Our results provide the first empirical evidence that the current theoretical understanding of molecular cloud structure derived from the solar neighborhood also holds in high-pressure environments. We therefore suggest that these theories may be applicable to understand star formation in the early universe.

  18. 46 CFR 151.50-34 - Vinyl chloride (vinyl chloride monomer).

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 5 2010-10-01 2010-10-01 false Vinyl chloride (vinyl chloride monomer). 151.50-34... chloride (vinyl chloride monomer). (a) Copper, aluminum, magnesium, mercury, silver, and their alloys shall... equipment that may come in contact with vinyl chloride liquid or vapor. (b) Valves, flanges, and...

  19. Determination of Benzalkonium Chloride Homologs in Complex Chemical Disinfectant by High-Performance Liquid Chromatography%复方化学消毒剂中苯扎氯铵的高效液相色谱测定

    Institute of Scientific and Technical Information of China (English)

    刘雯雯; 张瑾; 乔俊琴; 练鸿振

    2011-01-01

    建立了一种测定复方化学消毒剂中苯扎氯铵成分十二烷基二甲基苄基氯化铵、十四烷基二甲基苄基氯化铵和十六烷基二甲基苄基氯化铵的反相离子对高效液相色谱法.色谱柱为Platisil ODS(5 μm,250 mm×4.6 mm),流动相为甲醇-0.2 mol/L己烷磺酸钠(含1%三乙胺,V/V,用高氯酸调节至pH=6.0,体积比85∶15),紫外220 nm检测.用己烷磺酸钠作为离子对试剂,增强了苯扎氯铵成分的保留,三乙胺作为扫尾剂,通过抑制固定相表面残存的硅羟基对苯扎氯铵成分的吸附,减少了色谱峰拖尾.3种苯扎氯铵成分分离良好,标准曲线的线性范围分别为0.002~5 mg/mL、0.005~10 mg/mL和0.005~10 mg/mL,检测限分别为0.0005 mg/mL、0.001 mg/mL和0.001 mg/mL.方法具有良好的准确度和精密度,在测定低浓度样品时优势明显.实际用于测定苯扎氯铵消毒液和医用消毒纸巾中3种苯扎氯铵成分的含量,回收率为99.3%~104.1%,日内和日间测定相对标准偏差(RSD)均小于2.0%.%An ion pair reversed phase High-Performance Liquid Chromatography ( HPLC ) method has been developed for the simultaneous determination of benzalkonium chloride ( BAC ) homologues, dodecyl dimethyl benzyl ammonium chloride ( C12 ), tetradecyl dimethyl benzyl ammonium chloride ( C14 ) and cetyl dimethyl benzyl ammonium chloride ( C16 ), in complex chemical disinfectant. Separation was carried out on Platisil ODS column ( 5 μm, 250 mm ×4. 6 mm ), using methanol and 200 mmol/L hexane sulfonate sodium aqueous solution consisting of 1 % triethylamine ( V/V), adjusted with perchloric acid to pH 6. 0 ( 85 : 15, V/V) as the mobile phase in an isocratic elution. The detection wavelength was 220 nm. In the experiment, sodium hexanesulfonate was used as the ion-pair reagent to enhance the retention of benzalkonium chloride, and triethylamine was used as the tailing-suppressor to restrain the adsorption of benzalkonium chloride to the residual silanols

  20. Hot corrosion monitoring of alloy 617 in molten chlorides using electrochemical techniques

    Energy Technology Data Exchange (ETDEWEB)

    Perez, F.J.; Hierro, M.P.; Nieto, J. [Univ. Complutense de Madrid (Spain). Dept. de Ciencia de los Materiales, Facultad de Ciencias Quimicas

    2006-07-01

    Molten chloride mixtures are formed in waste incineration plants during waste firing and energy production. These mixtures are responsible for degradation processes like hot corrosion. In order to evaluate the damage of molten salt mixtures in waste incineration environments, the alloy 617 was exposed beneath a molten KCl-ZnCl{sub 2} mixture at 650 C in air. The corrosion process was monitored by electrochemical impedance spectroscopy (EIS). An extensive microscopy analysis have been done in order to correlate the electrochemical results, and to establish an electrochemical mechanism for such high temperature corrosion process. (orig.)

  1. Stable High-T {sub c} rf SQUID NDE system operating in noisy environment

    Energy Technology Data Exchange (ETDEWEB)

    He, D.F. [Superconducting Materials Center, National Institute for Materials Science, Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan)]. E-mail: he.dongfeng@nims.go.jp; Yoshizawa, M. [Iwate University, Ueda 4-3-5, Morioka 020-8551 (Japan); Itozaki, H. [Superconducting Materials Center, National Institute for Materials Science, Sengen 1-2-1, Tsukuba, Ibaraki 305-0047 (Japan)

    2006-04-15

    A high-T {sub c} rf SQUID NDE system was developed for stable, long time operation in a noisy environment. To reduce the influence of high frequency electromagnetic interference (EMI), a carefully designed metal shielding made of 0.1 mm thick metal foil was used. With the metal shielding, the SQUID could still operate well when a cellular phone was used nearby although the cellular phone could produce very strong EMI noises. To reduce the influence of the line interference or low frequency noises, a compensation method was used in the SQUID-based NDE system. With the compensation, the low frequency and the line interference could be reduced well. Using this SQUID-based NDE system, we successfully performed the NDE measurements in a noisy environment.

  2. CHLORIDE WASHER PERFORMACE TESTING

    Energy Technology Data Exchange (ETDEWEB)

    Coughlin, J; David Best, D; Robert Pierce, R

    2007-11-30

    Testing was performed to determine the chloride (Cl-) removal capabilities of the Savannah River National Laboratory (SRNL) designed and built Cl- washing equipment intended for HB-Line installation. The equipment to be deployed was tested using a cerium oxide (CeO2) based simulant in place of the 3013 plutonium oxide (PuO2) material. Two different simulant mixtures were included in this testing -- one having higher Cl- content than the other. The higher Cl- simulant was based on K-Area Interim Surveillance Inspection Program (KIS) material with Cl- content approximately equal to 70,000 ppm. The lower Cl- level simulant was comparable to KIS material containing approximately 8,000-ppm Cl- content. The performance testing results indicate that the washer is capable of reducing the Cl- content of both surrogates to below 200 ppm with three 1/2-liter washes of 0.1M sodium hydroxide (NaOH) solution. Larger wash volumes were used with similar results - all of the prescribed test parameters consistently reduced the Cl- content of the surrogate to a value below 200 ppm Cl- in the final washed surrogate material. The washer uses a 20-micron filter to retain the surrogate solids. Tests showed that 0.16-0.41% of the insoluble fraction of the starting mass passed through the 20-micron filter. The solids retention performance indicates that the fissile masses passing through the 20-micron filter should not exceed the waste acceptance criteria for discard in grout to TRU waste. It is recommended that additional testing be pursued for further verification and optimization purposes. It is likely that wash volumes smaller than those tested could still reduce the Cl- values to acceptable levels. Along with reduced wash volumes, reuse of the third wash volume (in the next run processed) should be tested as a wash solution minimization plan. A 67% reduction in the number of grouted paint pails could be realized if wash solution minimization testing returned acceptable results.

  3. Modelling and Control of Stepper Motors for High Accuracy Positioning Systems Used in Radioactive Environments

    OpenAIRE

    Picatoste Ruilope, Ricardo

    2014-01-01

    Hybrid Stepper Motors are widely used in open-loop position applications. They are the choice of actuation for the collimators in the Large Hadron Collider, the largest particle accelerator at CERN. In this case the positioning requirements and the highly radioactive operating environment are unique. The latter forces both the use of long cables to connect the motors to the drives which act as transmission lines and also prevents the use of standard position sensors. However, reliable and pre...

  4. Turbulence Sets the Initial Conditions for Star Formation in High-pressure Environments

    Science.gov (United States)

    Rathborne, J. M.; Longmore, S. N.; Jackson, J. M.; Kruijssen, J. M. D.; Alves, J. F.; Bally, J.; Bastian, N.; Contreras, Y.; Foster, J. B.; Garay, G.; Testi, L.; Walsh, A. J.

    2014-11-01

    Despite the simplicity of theoretical models of supersonically turbulent, isothermal media, their predictions successfully match the observed gas structure and star formation activity within low-pressure (P/k 107 K cm-3) environments, like those in the Galaxy's inner 200 pc central molecular zone (CMZ) and in the early universe. Here, we present Atacama Large Millimeter/submillimeter Array 3 mm dust continuum emission within a cloud, G0.253+0.016, which is immersed in the high-pressure environment of the CMZ. While the log-normal shape and dispersion of its column density probability distribution function (PDF) are strikingly similar to those of solar neighborhood clouds, there is one important quantitative difference: its mean column density is one to two orders of magnitude higher. Both the similarity and difference in the PDF compared to those derived from solar neighborhood clouds match predictions of turbulent cloud models given the high-pressure environment of the CMZ. The PDF shows a small deviation from log-normal at high column densities confirming the youth of G0.253+0.016. Its lack of star formation is consistent with the theoretically predicted, environmentally dependent volume density threshold for star formation which is orders of magnitude higher than that derived for solar neighborhood clouds. Our results provide the first empirical evidence that the current theoretical understanding of molecular cloud structure derived from the solar neighborhood also holds in high-pressure environments. We therefore suggest that these theories may be applicable to understand star formation in the early universe.

  5. Infant Temperament and High Risk Environment Relate to Behavior Problems and Language in Toddlers

    Science.gov (United States)

    Derauf, Chris; LaGasse, Linda; Smith, Lynne; Newman, Elana; Shah, Rizwan; Arria, Amelia; Huestis, Marilyn; Haning, William; Strauss, Arthur; Grotta, Sheri Della; Dansereau, Lynne; Lin, Hai; Lester, Barry

    2011-01-01

    Objective This study examined the role that easy infant temperament and cumulative environmental risk play in predicting cognitive, language and behavioral outcomes in 3 year-old children at high social risk. Methods Subjects were 412 mother-infant dyads, recruited at birth, participating in a longitudinal study examining the effects of prenatal methamphetamine (MA) on child development. This analysis includes a subsample (n=290) of the study with a completed 3 year visit. Temperament was assessed by the Infant Behavior Questionnaire at 12 mos. Factor analysis from well-validated measures generated “easy” and “difficult” temperament profiles, and a profile for high risk environment. Caretaker receptive vocabulary served as a proxy for IQ. Outcomes at 3 years included motor and mental development, behavior problems, and language. Linear regression and hierarchical linear modeling examined the effects of temperament, high risk environment and caregiver receptive language on outcomes adjusting for maternal drug use, demographic, and socioeconomic covariates. Results Internalizing and externalizing behaviors were lower in children with easy temperament and higher with increased environmental risk. Easy temperament attenuated behavioral problems only in the setting of lower environmental risk. Caregiver receptive language was associated with lower internalizing scores High risk environment and temperament factors were not related to cognitive or motor outcomes. Prenatal MA exposure was not associated with 3 year-old outcomes, nor did it alter the protective effects of an easier temperament on child behavior. Conclusions Children growing up in adverse social environments had increased behavioral problems and compromised language development. Conversely, an easy temperament acts as a protective factor for social-emotional development and could be related to resilience. PMID:21200329

  6. Degradation of Solar Array Components in a Combined UV/VUV High Temperature Test Environment

    Directory of Open Access Journals (Sweden)

    Nömayr Christel

    2017-01-01

    A design verification test under UV/VUV conditions of sun exposed materials and technologies on component level is presented which forms part of the overall verification and qualification of the solar array design of the MTM and MPO. The test concentrates on the self-contamination aspects and the resulting performance losses of the solar array under high intensity and elevated temperature environment representative for the photovoltaic assembly (PVA.

  7. Chemical Compatibility of High-Performance Engineering Thermoplastics in Compressor Environments

    OpenAIRE

    Pai-Paranjape, Vandita

    2014-01-01

    The compressor industry faces a difficult design environment for achieving performance improvement, reduced cost, and lower environmental footprint. In order to address some of these challenges, thermoplastics can be considered as a replacement for metal in some compressor parts. Thermoplastics have been found to be suitable for steel replacement in structural parts for automotive and brass replacement in water-handling applications such as meters. As such, we believe certain high-performance...

  8. On the HEMP (high-altitude electromagnetic pulse) environment for protective relays

    Energy Technology Data Exchange (ETDEWEB)

    Thomas, D.E.; Wiggins, C.M.; Salas, T.M. (BDM International, Inc., Albuquerque, NM (USA)); Barnes, P.R. (Oak Ridge National Lab., TN (USA))

    1990-01-01

    An assessment of the transient environment for protective relays produced by high-altitude electromagnetic pulse (HEMP) events is presented in this paper. Several mechanisms for coupling of HEMP to relay terminals are used to develop estimates of possible HEMP threats to relays. These predicted relay responses to HEMP events are compared to measured data on a solid state based relay's impulse strength. 12 refs., 13 figs., 3 tabs.

  9. High levels of Mercury and Lead detected by hair analysis in two Venezuelan environments

    OpenAIRE

    Marcano,Eunice; Labady,Mary; Gomes,Clara; Aguiar,Guillermina; Laine,Jorge

    2009-01-01

    Mercury and Lead concentrations obtained by ICP-OAS analysis of human hair from riverside communities along the Orinoco river in the Amazon state (Venezuela) were compared with those from Caracas, Venezuela. Taking into account the characteristics of these two environments and the values of the average concentrations of Mercury and Lead, baselines were established suggesting that gold mining activity near the Orinoco river is responsible for the high levels of Mercury in hair from the Amazon ...

  10. Performances of 250 Amp-hr lithium/thionyl chloride cells

    Science.gov (United States)

    Goualard, Jacques

    1991-05-01

    A 250 Ah lithium thionyl chloride battery is being developed for a booster rocket engine. Extensive cell testing is running to evaluate functional and safety performances. Some results are presented. The lithium/thionyl chloride batteries were selected for their high energy density (low weight) as compared to other sources. The temperature of a lower weight item will be more sensitive to variations of internal and external heat fluxes than a heavier one. The use of high energy density L/TC batteries is subjected to stringent thermal environments to have benefit of energy density and to stay safe in any conditions. The battery thermal environment and discharge rate have to be adjusted to obtain the right temperature range at cell level, to have the maximum performances. Voltage and capacity are very sensitive to temperature. This temperature is the cell internal actual temperature during discharge. This temperature is directed by external thermal environment and by cell internal heat dissipation, i.e., cell actual voltage.

  11. Performances of 250 Amp-hr lithium/thionyl chloride cells

    Science.gov (United States)

    Goualard, Jacques

    1991-01-01

    A 250 Ah lithium thionyl chloride battery is being developed for a booster rocket engine. Extensive cell testing is running to evaluate functional and safety performances. Some results are presented. The lithium/thionyl chloride batteries were selected for their high energy density (low weight) as compared to other sources. The temperature of a lower weight item will be more sensitive to variations of internal and external heat fluxes than a heavier one. The use of high energy density L/TC batteries is subjected to stringent thermal environments to have benefit of energy density and to stay safe in any conditions. The battery thermal environment and discharge rate have to be adjusted to obtain the right temperature range at cell level, to have the maximum performances. Voltage and capacity are very sensitive to temperature. This temperature is the cell internal actual temperature during discharge. This temperature is directed by external thermal environment and by cell internal heat dissipation, i.e., cell actual voltage.

  12. Analysis of chloride diffusivity in concrete containing red mud

    Directory of Open Access Journals (Sweden)

    D.V. Ribeiro

    Full Text Available Red mud is a solid waste produced in the alumina production process and, due to its high pH, is classified as hazardous. Its incorporation in concrete mixtures, acting as filler due to the particles fineness, might be an interesting reuse alternative. The focus of this paper is to study the chloride diffusivity of concrete mixtures containing red-mud. The concentration of chlorides was monitored by measuring the conductivity of the anolyte, which was distilled water initially. In addition, the estimation of the chloride ions diffusion coefficients in steady and non-steady conditions, Ds and Dns, was obtained from the ''time-lag'' and ''equivalent time'' between diffusion and migration experiments. Due to superfine particle-size distribution and the "filler" effect, the red mud addition seems to assure lower chloride diffusivity.

  13. Chloride supporting electrolytes for all-vanadium redox flow batteries.

    Science.gov (United States)

    Kim, Soowhan; Vijayakumar, M; Wang, Wei; Zhang, Jianlu; Chen, Baowei; Nie, Zimin; Chen, Feng; Hu, Jianzhi; Li, Liyu; Yang, Zhenguo

    2011-10-28

    This paper examines vanadium chloride solutions as electrolytes for an all-vanadium redox flow battery. The chloride solutions were capable of dissolving more than 2.3 M vanadium at varied valence states and remained stable at 0-50 °C. The improved stability appeared due to the formation of a vanadium dinuclear [V(2)O(3)·4H(2)O](4+) or a dinuclear-chloro complex [V(2)O(3)Cl·3H(2)O](3+) in the solutions over a wide temperature range. The all-vanadium redox flow batteries with the chloride electrolytes demonstrated excellent reversibility and fairly high efficiencies. Only negligible, if any, gas evolution was observed. The improved energy capacity and good performance, along with the ease in heat management, would lead to substantial reduction in capital cost and life-cycle cost, making the vanadium chloride redox flow battery a promising candidate for stationary applications.

  14. Limits to the thermal tolerance of corals adapted to a highly fluctuating, naturally extreme temperature environment

    Science.gov (United States)

    Schoepf, Verena; Stat, Michael; Falter, James L.; McCulloch, Malcolm T.

    2015-12-01

    Naturally extreme temperature environments can provide important insights into the processes underlying coral thermal tolerance. We determined the bleaching resistance of Acropora aspera and Dipsastraea sp. from both intertidal and subtidal environments of the naturally extreme Kimberley region in northwest Australia. Here tides of up to 10 m can cause aerial exposure of corals and temperatures as high as 37 °C that fluctuate daily by up to 7 °C. Control corals were maintained at ambient nearshore temperatures which varied diurnally by 4-5 °C, while treatment corals were exposed to similar diurnal variations and heat stress corresponding to ~20 degree heating days. All corals hosted Symbiodinium clade C independent of treatment or origin. Detailed physiological measurements showed that these corals were nevertheless highly sensitive to daily average temperatures exceeding their maximum monthly mean of ~31 °C by 1 °C for only a few days. Generally, Acropora was much more susceptible to bleaching than Dipsastraea and experienced up to 75% mortality, whereas all Dipsastraea survived. Furthermore, subtidal corals, which originated from a more thermally stable environment compared to intertidal corals, were more susceptible to bleaching. This demonstrates that while highly fluctuating temperatures enhance coral resilience to thermal stress, they do not provide immunity to extreme heat stress events.

  15. Limits to the thermal tolerance of corals adapted to a highly fluctuating, naturally extreme temperature environment.

    Science.gov (United States)

    Schoepf, Verena; Stat, Michael; Falter, James L; McCulloch, Malcolm T

    2015-12-02

    Naturally extreme temperature environments can provide important insights into the processes underlying coral thermal tolerance. We determined the bleaching resistance of Acropora aspera and Dipsastraea sp. from both intertidal and subtidal environments of the naturally extreme Kimberley region in northwest Australia. Here tides of up to 10 m can cause aerial exposure of corals and temperatures as high as 37 °C that fluctuate daily by up to 7 °C. Control corals were maintained at ambient nearshore temperatures which varied diurnally by 4-5 °C, while treatment corals were exposed to similar diurnal variations and heat stress corresponding to ~20 degree heating days. All corals hosted Symbiodinium clade C independent of treatment or origin. Detailed physiological measurements showed that these corals were nevertheless highly sensitive to daily average temperatures exceeding their maximum monthly mean of ~31 °C by 1 °C for only a few days. Generally, Acropora was much more susceptible to bleaching than Dipsastraea and experienced up to 75% mortality, whereas all Dipsastraea survived. Furthermore, subtidal corals, which originated from a more thermally stable environment compared to intertidal corals, were more susceptible to bleaching. This demonstrates that while highly fluctuating temperatures enhance coral resilience to thermal stress, they do not provide immunity to extreme heat stress events.

  16. Sleep position and the ocular surface in a high airflow environment

    Science.gov (United States)

    Gauba, Vinod; Curtis, Zoe J.

    2013-01-01

    Purpose To study the relationship between sleep position and ocular surface symptoms and signs in an high air flow environment. Methods Prospective observational study of new patients attending the dry eye clinic was performed. Patients with pre-existing ocular history, relevant systemic history (e.g. Sjogren’s syndrome) or who were using topical or systemic therapy for dry eye were not included. Data were collected from the patient to document their dry eye symptoms; preferred dependent sleeping side and their bedroom airflow. All patients were examined by a clinician blind to the patient’s responses where Schirmer’s test and slit lamp examination were performed looking for the presence of lagophthalmos and corneal epitheliopathy. Results 48 patients enrolled into the study of which 23 were males and 25 were females with a normal and comparable age distribution. The study found a strong association between patients’ preferred sleeping side and the incidence of corneal epitheliopathy in the contralateral eye particularly in patients with evidence of lagophthalmos. Dry eye symptoms were found to be worse and tear production lower on the contralateral side to the preferred sleeping side particularly in patients who sleep in a high airflow environment. Conclusion In patients sleeping in a high airflow environment with nocturnal lagophthalmos, this study observed an association between preferred dependent sleep position and increased dry eye symptoms, lower Schirmer’s scores and increased corneal epitheliopathy in the contralateral eye. PMID:24526862

  17. High mortality and poor growth of green mussels, Perna viridis, in high chlorophyll- a environment

    Science.gov (United States)

    Soon, Tan Kar; Denil, Delta Jenetty; Ransangan, Julian

    2016-03-01

    The current study was carried out from May 2014 to April 2015 to estimate the stock status of P. viridis in Marudu Bay. The gonad development was monitored by histological examination, while the population parameters including asymptotic length ( L ∞), growth coefficient ( K), mortality rate ( Z, F and M), exploitation level ( E) and recruitment of P. viridis were estimated using the lengthfrequency data. Results of the current study demonstrated that P. viridis in Marudu Bay spawned throughout the year with two major peaks, one in April to May and another one in October to December. The recruitment pattern was continuous with the peak in May to June 2014, which corresponded to the first spawning peak in April. However, no significant recruitment was observed from the second spawning peak due to the difference in spawning timing between male and female populations. The estimated asymptotic length ( L ∞), growth coefficient ( K), total mortality ( Z), natural mortality ( M), fishing mortality ( F) and growth performance ( φ) of P. viridis in Marudu Bay were estimate to be 117 mm, 0.97 yr-1, 4.39 yr-1, 1.23 yr-1, 3.16 yr-1 and 4.123, respectively. The exponent b of the lengthweight relationship was 2.4 and exploitation level ( E) was 0.72. The high mortality, low condition indices and negative allometric of P. viridis in Marudu Bay is caused by a lack of suitable food in the surrounding water.

  18. Neighborhood environment and urban African American marijuana use during high school.

    Science.gov (United States)

    Reboussin, Beth A; Green, Kerry M; Milam, Adam J; Furr-Holden, C Debra M; Ialongo, Nicholas S

    2014-12-01

    African American male high school students have the highest rates of marijuana use among all racial, ethnic, and gender groups, yet there is limited research examining contextual factors salient to the African American community. The purpose of this study was to examine how neighborhood environment measured in 8th grade is related to longitudinal transitions in marijuana use during high school (9th to 12th grades) in a sample of urban African Americans. Four hundred and fifty-two African American children were interviewed annually beginning in 1st grade as part of a longitudinal field study in Baltimore city. Latent transition analysis indicated early in high school posed the greatest risk for initiation and progression of marijuana use. Community violence exposure was associated with an increased likelihood of transitioning from no marijuana use to infrequent use (adjusted odds ratios (AOR) = 2.40, p marijuana use. There was evidence for partial mediation of these associations by perceptions of harm and depressed mood. Drug activity and sales was associated with progression from infrequent to frequent and problematic use (AOR = 2.87, p = 0.029). African American youth living in urban environments with exposure to drug activity, violence, and neighborhood disorder are at increased risk for both initiation and progression to more frequent and problematic marijuana use during high school. These findings highlight the need to develop interventions for African American youth that are mindful of the impact of the additional stressors of living in a high-risk urban environment during a critical developmental transition period. Reducing exposure to drug activity and violence in high-risk urban neighborhoods may be the first step to potentially halt increasing rates of marijuana use among African Americans.

  19. Removal of chloride from electric arc furnace dust.

    Science.gov (United States)

    Chen, Wei-Sheng; Shen, Yun-Hwei; Tsai, Min-Shing; Chang, Fang-Chih

    2011-06-15

    Electric arc furnace (EAF) dust with high chloride content increases the threat of dioxin emissions and the high chloride content reduces the value of recycled zinc oxide produced by EAF dust recycling plants. This study conducts a number of laboratory experiments to determine the technical feasibility of a new dechlorination method. These methods consist of a series of roasting processes and water washing processes. In the roasting process, EAF dust was heated in a tube furnace to evaluate the parameters of atmospheric conditions, roasting temperature, and roasting time. Results indicate that sulfation roasting is more efficient in reducing chloride content than other roasting processes. The water washing process can totally remove water-soluble chloride at a solid to liquid ratio of 1:10. However, the remaining water-insoluble substance is difficult to dechlorinate. For example, lead chloride forms a hydroxyl-halide (PbOHCl) and lead chloride carbonate (Pb(2)CO(3)Cl(2)) agglutinative matrix that is hard to wash away.

  20. Distributed High Accuracy Peer-to-Peer Localization in Mobile Multipath Environments

    CERN Document Server

    Ekambaram, Venkatesan

    2010-01-01

    In this paper we consider the problem of high accuracy localization of mobile nodes in a multipath-rich environment where sub-meter accuracies are required. We employ a peer to peer framework where the vehicles/nodes can get pairwise multipath-degraded ranging estimates in local neighborhoods together with a fixed number of anchor nodes. The challenge is to overcome the multipath-barrier with redundancy in order to provide the desired accuracies especially under severe multipath conditions when the fraction of received signals corrupted by multipath is dominating. We invoke a message passing analytical framework based on particle filtering and reveal its high accuracy localization promise through simulations.

  1. Improvement and Optimization of Testing Methods for Chloride in High - sulfur Sour Water%高含硫污水氯化物测定方法的改进和优化

    Institute of Scientific and Technical Information of China (English)

    郝新焕; 崔轲龙; 马红杰; 徐奕

    2012-01-01

    The degree of corrosion and corrosion rate of refinery equipment are closely related to chlorides content.Therefore,the testing of chlorides in one of important testing items in corrosion monitoring of refinery process units.The large amount of sulfides,ammonia and nitrogen etc in the sour water of refinery imposes great difficulties in the accurate testing of chlorides in sour water.Through the testing,several common pre-treatment methods are screened and selected.The interference of chlorides,ammonia and nitrogen can be eliminated by filtration,thermal vaporization,oxydol counteracting at acidic conditions and boiling at alkaline conditions.The applicabilities of silver nitrate titration method and mercury nitrate titration method are evaluated.The results show that the mercury nitrate titration method is good in stability,lower in testing limit,which is more applicable in corrosion monitoring.The multiple tests of high-sulfur sour water samples by the new improved testing method demonstrates that the relative deviation is 0% ~ 16.95,and spiked recovery is 93.85% ~ 104.95%.%炼油设备腐蚀程度及速度与氯化物含量关系密切,氯化物检测是炼油装置腐蚀监测的重要项目之一。炼油装置的污水中含有大量的硫化物和氨氮等干扰物质,给污水中氯化物的准确测定造成困难。对比了几种常见的前处理方法,发现对样品进行过滤、加热挥发、酸性条件下双氧水消解和碱性条件下煮沸等处理后可消除硫化物和氨氮的干扰。结合实际情况对硝酸银滴定法和硝酸汞滴定法的适用性进行了评选,评选结果表明,硝酸汞滴定法稳定性好,检出限更低,更贴近腐蚀监测的实际需要。采用改进后的新测定方法来测定高含硫污水样品,多次平行测定的相对标准偏差为0%~16.95%,加标回收率为93.85%~104.59%。

  2. High-Frequency Dynamic Analysis of Plates in Thermal Environments Based on Energy Finite Element Method

    Directory of Open Access Journals (Sweden)

    Di Wang

    2015-01-01

    Full Text Available The energy density governing equation to analyze the high-frequency dynamic behavior of plates in thermal environments is derived in this paper, in which the thermal effects are considered to change the membrane stress state and temperature dependent material properties of plates. Then the thermal effects on the energy reflection and transmission coefficients are dealt with hereof. Based on the above, an EFEM (energy finite element method based approximate approach for the energy analysis of coupled plates under nonuniform thermal environments is proposed. The approach could be conducted by three steps: (1 thermal analysis, (2 thermal stress analysis, and (3 forming element matrixes, joint matrixes, and the whole EFEM formulation for the energy analysis. The same mesh model is used for all the three steps. The comparison between EFEM results and classical modal superposition method results of simply supported plates in various uniform thermal environments and coupled plates in nonuniform thermal environments demonstrated that the derived energy governing equation and the proposed approach described well the smooth time- and locally space-averaged energy density. It is found that the distributions and levels of energy density are affected by thermal effects, and the variation trends are related to exciting frequency.

  3. The Association Between Supportive High School Environments and Depressive Symptoms and Suicidality Among Sexual Minority Students.

    Science.gov (United States)

    Denny, Simon; Lucassen, Mathijs F G; Stuart, Jaimee; Fleming, Theresa; Bullen, Pat; Peiris-John, Roshini; Rossen, Fiona V; Utter, Jennifer

    2016-01-01

    The purpose of this study was to determine if sexual minority students in supportive school environments experienced fewer depressive symptoms and lower rates of suicide ideation, plans and attempts ("suicidality") than sexual minority students in less supportive school environments. In 2007, a nationally representative sample (N = 9,056) of students from 96 high schools in New Zealand used Internet tablets to complete a health and well-being survey that included questions on sexual attractions, depressive symptoms, and suicidality. Students reported their experience of supportive environments at school and gay, lesbian, bisexual, and transgender (GLBT) bullying, and these items were aggregated to the school level. Teachers (n = 2,901) from participating schools completed questionnaires on aspects of school climate, which included how supportive their schools were toward sexual minority students. Multilevel models were used to estimate school effects on depressive symptoms and suicidality controlling for background characteristics of students. Sexual minority students were more likely to report higher levels of depressive symptoms and suicidality than their opposite-sex attracted peers (p suicidality (p < .001) than in schools where students reported less favorable school climates. These results suggest that schools play an important role in providing safe and supportive environments for male sexual minority students.

  4. The development of chloride ion selective polypyrrole thin film on a layer-by-layer carbon nanotube working electrode

    Science.gov (United States)

    Liu, Yang; Lynch, Jerome

    2011-04-01

    A chloride ion selective thin film sensor is proposed for measuring chloride ion concentration, which is an environmental parameter correlated to corrosion. In this work, electrochemical polymerization of Polypyrrole (PPy) doped with chloride ions was achieved on the top of a carbon nanotube (CNT) thin film as a working electrode in an electrochemical cell. The underlying CNT layer conjugated with doped PPy thin film can form a multifunctional "selfsensing" material platform for chloride ion detection in a concrete environment. The paper presents the first type of work using CNT and PPy as hybrid materials for chloride ion sensing. Electrochemical polymerization of PPy results in oxidation that yields an average of one positive charge distributed over four pyrrole units. This positive charge is compensated by negatively-charged chloride ions in the supporting electrolyte. In effect, the chloride ion-doped PPy has become molecularly imprinted with chloride ions thereby providing it with some degree of perm-selectivity for chloride ions. The detection limit of the fabricated chloride ion-doped PPy thin film can reach 10-8 M and selectivity coefficients are comparable to those in the literature. The reported work aims to lay a strong foundation for detecting chloride ion concentrations in the concrete environment.

  5. Direct measurements of near-highway emissions in a high diesel environment

    Science.gov (United States)

    DeWitt, H. L.; Hellebust, S.; Temime-Roussel, B.; Ravier, S.; Polo, L.; Jacob, V.; Buisson, C.; Charron, A.; André, M.; Pasquier, A.; Besombes, J. L.; Jaffrezo, J. L.; Wortham, H.; Marchand, N.

    2014-10-01

    Diesel-powered passenger cars currently outnumber gasoline-powered cars in many countries, particularly in Europe. In France, diesel cars represented 61% of Light Duty Vehicles in 2011 and this percentage is still increasing (French Environment and Energy Management Agency, ADEME). As part of the September~2011 joint PM-DRIVE (Particulate Matter- DiRect and Indirect on-road Vehicular Emissions) and MOCOPO (Measuring and mOdeling traffic COngestion and POllution) field campaign, the concentration and high-resolution chemical composition of aerosols and volatile organic carbon (VOC) species were measured adjacent to a major urban highway south of Grenoble, France. Alongside these atmospheric measurements, detailed traffic data were collected from nearby traffic cameras and loop detectors, which allowed the identification of vehicle type and characteristics, traffic concentration, and traffic speed to be quantified and compared to measured aerosol and VOCs. Six aerosol age and source profiles were resolved using the positive matrix factorization (PMF) model on real-time high-resolution aerosol mass spectra. These six aerosol source/age categories included a hydrocarbon-like organic aerosol (HOA) commonly associated with primary vehicular emissions, a nitrogen containing aerosol (NOA) with a diurnal pattern similar to that of HOA, oxidized organic aerosol (OOA), and biomass burning aerosol (BBOA). While quantitatively separating the influence of diesel vs. gasoline proved impossible, a low HOA : black carbon ratio, similar to that measured in other high-diesel environments, and high levels of NOx, also indicative of diesel emissions, were observed. A comparison between these high-diesel environment measurements and measurements taken in low-diesel (North American) environments was examined and the potential feedback between vehicular emissions and SOA formation was probed. Although the measurement site was located next to a large source of primary emissions, which are

  6. Direct measurements of near-highway emissions in a high diesel environment

    Directory of Open Access Journals (Sweden)

    H. L. DeWitt

    2014-10-01

    Full Text Available Diesel-powered passenger cars currently outnumber gasoline-powered cars in many countries, particularly in Europe. In France, diesel cars represented 61% of Light Duty Vehicles in 2011 and this percentage is still increasing (French Environment and Energy Management Agency, ADEME. As part of the September~2011 joint PM-DRIVE (Particulate Matter- DiRect and Indirect on-road Vehicular Emissions and MOCOPO (Measuring and mOdeling traffic COngestion and POllution field campaign, the concentration and high-resolution chemical composition of aerosols and volatile organic carbon (VOC species were measured adjacent to a major urban highway south of Grenoble, France. Alongside these atmospheric measurements, detailed traffic data were collected from nearby traffic cameras and loop detectors, which allowed the identification of vehicle type and characteristics, traffic concentration, and traffic speed to be quantified and compared to measured aerosol and VOCs. Six aerosol age and source profiles were resolved using the positive matrix factorization (PMF model on real-time high-resolution aerosol mass spectra. These six aerosol source/age categories included a hydrocarbon-like organic aerosol (HOA commonly associated with primary vehicular emissions, a nitrogen containing aerosol (NOA with a diurnal pattern similar to that of HOA, oxidized organic aerosol (OOA, and biomass burning aerosol (BBOA. While quantitatively separating the influence of diesel vs. gasoline proved impossible, a low HOA : black carbon ratio, similar to that measured in other high-diesel environments, and high levels of NOx, also indicative of diesel emissions, were observed. A comparison between these high-diesel environment measurements and measurements taken in low-diesel (North American environments was examined and the potential feedback between vehicular emissions and SOA formation was probed. Although the measurement site was located next to a large source of primary emissions

  7. Photonic crystal fiber based chloride chemical sensors for corrosion monitoring

    Science.gov (United States)

    Wei, Heming; Tao, Chuanyi; Krishnaswamy, Sridhar

    2016-04-01

    Corrosion of steel is one of the most important durability issues in reinforced concrete (RC) structures because aggressive ions such as chloride ions permeate concrete and corrode steel, consequently accelerating the destruction of structures, especially in marine environments. There are many practical methods for corrosion monitoring in RC structures, mostly focusing on electrochemical-based sensors for monitoring the chloride ion which is thought as one of the most important factors resulting in steel corrosion. In this work, we report a fiber-optic chloride chemical sensor based on long period gratings inscribed in a photonic crystal fiber (PCF) with a chloride sensitive thin film. Numerical simulation is performed to determine the characteristics and resonance spectral response versus the refractive indices of the analyte solution flowing through into the holes in the PCF. The effective refractive index of the cladding mode of the LPGs changes with variations of the analyte solution concentration, resulting in a shift of the resonance wavelength, hence providing the sensor signal. This fiber-optic chemical sensor has a fast response, is easy to prepare and is not susceptible to electromagnetic environment, and can therefore be of use for structural health monitoring of RC structures subjected to such aggressive environments.

  8. Corrosion of Carbon Steel and Corrosion-Resistant Rebars in Concrete Structures Under Chloride Ion Attack

    Science.gov (United States)

    Mohamed, Nedal; Boulfiza, Mohamed; Evitts, Richard

    2013-03-01

    Corrosion of reinforced concrete is the most challenging durability problem that threatens reinforced concrete structures, especially structures that are subject to severe environmental conditions (i.e., highway bridges, marine structures, etc.). Corrosion of reinforcing steel leads to cracking and spalling of the concrete cover and billions of dollars are spent every year on repairing such damaged structures. New types of reinforcements have been developed to avoid these high-cost repairs. Thus, it is important to study the corrosion behavior of these new types of reinforcements and compare them to the traditional carbon steel reinforcements. This study aimed at characterizing the corrosion behavior of three competing reinforcing steels; conventional carbon steel, micro-composite steel (MMFX-2) and 316LN stainless steel, through experiments in carbonated and non-carbonated concrete exposed to chloride-laden environments. Synthetic pore water solutions have been used to simulate both cases of sound and carbonated concrete under chloride ions attack. A three-electrode corrosion cell is used for determining the corrosion characteristics and rates. Multiple electrochemical techniques were applied using a Gamry PC4™ potentiostat manufactured by Gamry Instruments (Warminster, PA). DC corrosion measurements were applied on samples subjected to fixed chloride concentration in the solution.

  9. High Speed Railway Environment Safety Evaluation Based on Measurement Attribute Recognition Model

    Directory of Open Access Journals (Sweden)

    Qizhou Hu

    2014-01-01

    Full Text Available In order to rationally evaluate the high speed railway operation safety level, the environmental safety evaluation index system of high speed railway should be well established by means of analyzing the impact mechanism of severe weather such as raining, thundering, lightning, earthquake, winding, and snowing. In addition to that, the attribute recognition will be identified to determine the similarity between samples and their corresponding attribute classes on the multidimensional space, which is on the basis of the Mahalanobis distance measurement function in terms of Mahalanobis distance with the characteristics of noncorrelation and nondimensionless influence. On top of the assumption, the high speed railway of China environment safety situation will be well elaborated by the suggested methods. The results from the detailed analysis show that the evaluation is basically matched up with the actual situation and could lay a scientific foundation for the high speed railway operation safety.

  10. Lung sounds auscultation technology based on ANC-ICA algorithm in high battlefield noise environment

    Institute of Scientific and Technical Information of China (English)

    牛海军; 冯安吉; 万明习; 白培瑞

    2003-01-01

    AIM:To explore the more accurate lung sounds auscultation technology in high battlefield noise environment.METHODS: In this study, we restrain high background noise using a new method-adaptive noise canceling based on independent component analysis (ANC-ICA), the method, by incorporating both second-order and higher-order statistics can remove noise components of the primary input signal based on statistical independence.RESULTS:The algorithm retained the local feature of lung sounds while eliminating high background noise, and performed more effectively than the conventional LMS algorithm.CONCLUSION:This method can cancel high battlefield noise of lung sounds effectively thus can help diagnose lung disease more accurately.

  11. High Speed Railway Environment Safety Evaluation Based on Measurement Attribute Recognition Model

    Science.gov (United States)

    Hu, Qizhou; Zhang, Bing

    2014-01-01

    In order to rationally evaluate the high speed railway operation safety level, the environmental safety evaluation index system of high speed railway should be well established by means of analyzing the impact mechanism of severe weather such as raining, thundering, lightning, earthquake, winding, and snowing. In addition to that, the attribute recognition will be identified to determine the similarity between samples and their corresponding attribute classes on the multidimensional space, which is on the basis of the Mahalanobis distance measurement function in terms of Mahalanobis distance with the characteristics of noncorrelation and nondimensionless influence. On top of the assumption, the high speed railway of China environment safety situation will be well elaborated by the suggested methods. The results from the detailed analysis show that the evaluation is basically matched up with the actual situation and could lay a scientific foundation for the high speed railway operation safety. PMID:25435866

  12. High speed railway environment safety evaluation based on measurement attribute recognition model.

    Science.gov (United States)

    Hu, Qizhou; Gao, Ningbo; Zhang, Bing

    2014-01-01

    In order to rationally evaluate the high speed railway operation safety level, the environmental safety evaluation index system of high speed railway should be well established by means of analyzing the impact mechanism of severe weather such as raining, thundering, lightning, earthquake, winding, and snowing. In addition to that, the attribute recognition will be identified to determine the similarity between samples and their corresponding attribute classes on the multidimensional space, which is on the basis of the Mahalanobis distance measurement function in terms of Mahalanobis distance with the characteristics of noncorrelation and nondimensionless influence. On top of the assumption, the high speed railway of China environment safety situation will be well elaborated by the suggested methods. The results from the detailed analysis show that the evaluation is basically matched up with the actual situation and could lay a scientific foundation for the high speed railway operation safety.

  13. Electrochemical Chloride extraction using external electrodes?

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Pedersen, Anne Juul

    2006-01-01

    Electrochemical methods for the removal of chloride from concrete have been developed and the methods are primarily designed for situations where corrosion has started due to an increased chloride concentration in the vicinity of the reinforcement. In these methods the reinforcement is used...... as the cathode. However, some unwanted side effects can occur, including alkali-silica reaction and in some cases hydrogen embrittlement. It is also suggested also to use electrochemical chloride extraction in a preventive way in constructions where chloride induced corrosion is likely to be a problem after...... a period of time, i.e. remove the chlorides before the chloride front reaches the reinforcement. If the chlorides are removed from outer few centimetres from the surface, the chloride will not reach the reinforcement and cause damage. By using the electrochemical chloride removal in this preventive way...

  14. A High-Fidelity Virtual Environment for the Study of Paranoia

    Directory of Open Access Journals (Sweden)

    Matthew R. Broome

    2013-01-01

    Full Text Available Psychotic disorders carry social and economic costs for sufferers and society. Recent evidence highlights the risk posed by urban upbringing and social deprivation in the genesis of paranoia and psychosis. Evidence based psychological interventions are often not offered because of a lack of therapists. Virtual reality (VR environments have been used to treat mental health problems. VR may be a way of understanding the aetiological processes in psychosis and increasing psychotherapeutic resources for its treatment. We developed a high-fidelity virtual reality scenario of an urban street scene to test the hypothesis that virtual urban exposure is able to generate paranoia to a comparable or greater extent than scenarios using indoor scenes. Participants (n=32 entered the VR scenario for four minutes, after which time their degree of paranoid ideation was assessed. We demonstrated that the virtual reality scenario was able to elicit paranoia in a nonclinical, healthy group and that an urban scene was more likely to lead to higher levels of paranoia than a virtual indoor environment. We suggest that this study offers evidence to support the role of exposure to factors in the urban environment in the genesis and maintenance of psychotic experiences and symptoms. The realistic high-fidelity street scene scenario may offer a useful tool for therapists.

  15. Antiviral effect of lithium chloride on infection of cells by canine parvovirus.

    Science.gov (United States)

    Zhou, Pei; Fu, Xinliang; Yan, Zhongshan; Fang, Bo; Huang, San; Fu, Cheng; Hong, Malin; Li, Shoujun

    2015-11-01

    Canine parvovirus type 2 causes significant viral disease in dogs, with high morbidity, high infectivity, and high mortality. Lithium chloride is a potential antiviral drug for viruses. We determined the antiviral effect of Lithium Chloride on canine parvovirus type 2 in feline kidney cells. The viral DNA and proteins of canine parvovirus were suppressed in a dose-dependent manner by lithium chloride. Further investigation verified that viral entry into cells was inhibited in a dose-dependent manner by lithium chloride. These results indicated that lithium chloride could be a potential antiviral drug for curing dogs with canine parvovirus infection. The specific steps of canine parvovirus entry into cells that are affected by lithium chloride and its antiviral effect in vivo should be explored in future studies.

  16. Expected environments in high-level nuclear waste and spent fuel repositories in salt

    Energy Technology Data Exchange (ETDEWEB)

    Claiborne, H.C.; Rickertsen, L.D., Graham, R.F.

    1980-08-01

    The purpose of this report is to describe the expected environments associated with high-level waste (HLW) and spent fuel (SF) repositories in salt formations. These environments include the thermal, fluid, pressure, brine chemistry, and radiation fields predicted for the repository conceptual designs. In this study, it is assumed that the repository will be a room and pillar mine in a rock-salt formation, with the disposal horizon located approx. 2000 ft (610 m) below the surface of the earth. Canistered waste packages containing HLW in a solid matrix or SF elements are emplaced in vertical holes in the floor of the rooms. The emplacement holes are backfilled with crushed salt or other material and sealed at some later time. Sensitivity studies are presented to show the effect of changing the areal heat load, the canister heat load, the barrier material and thickness, ventilation of the storage room, and adding a second row to the emplacement configuration. The calculated thermal environment is used as input for brine migration calculations. The vapor and gas pressure will gradually attain the lithostatic pressure in a sealed repository. In the unlikely event that an emplacement hole will become sealed in relatively early years, the vapor space pressure was calculated for three scenarios (i.e., no hole closure - no backfill, no hole closure - backfill, and hole closure - no backfill). It was assumed that the gas in the system consisted of air and water vapor in equilibrium with brine. A computer code (REPRESS) was developed assuming that these changes occur slowly (equilibrium conditions). The brine chemical environment is outlined in terms of brine chemistry, corrosion, and compositions. The nuclear radiation environment emphasized in this report is the stored energy that can be released as a result of radiation damage or crystal dislocations within crystal lattices.

  17. An Interactive, Web-based High Performance Modeling Environment for Computational Epidemiology.

    Science.gov (United States)

    Deodhar, Suruchi; Bisset, Keith R; Chen, Jiangzhuo; Ma, Yifei; Marathe, Madhav V

    2014-07-01

    We present an integrated interactive modeling environment to support public health epidemiology. The environment combines a high resolution individual-based model with a user-friendly web-based interface that allows analysts to access the models and the analytics back-end remotely from a desktop or a mobile device. The environment is based on a loosely-coupled service-oriented-architecture that allows analysts to explore various counter factual scenarios. As the modeling tools for public health epidemiology are getting more sophisticated, it is becoming increasingly hard for non-computational scientists to effectively use the systems that incorporate such models. Thus an important design consideration for an integrated modeling environment is to improve ease of use such that experimental simulations can be driven by the users. This is achieved by designing intuitive and user-friendly interfaces that allow users to design and analyze a computational experiment and steer the experiment based on the state of the system. A key feature of a system that supports this design goal is the ability to start, stop, pause and roll-back the disease propagation and intervention application process interactively. An analyst can access the state of the system at any point in time and formulate dynamic interventions based on additional information obtained through state assessment. In addition, the environment provides automated services for experiment set-up and management, thus reducing the overall time for conducting end-to-end experimental studies. We illustrate the applicability of the system by describing computational experiments based on realistic pandemic planning scenarios. The experiments are designed to demonstrate the system's capability and enhanced user productivity.

  18. Perception of the thermal environment in high school and university classrooms: Subjective preferences and thermal comfort

    Energy Technology Data Exchange (ETDEWEB)

    Corgnati, Stefano Paolo; Filippi, Marco; Viazzo, Sara [Department of Energy (DENER), Politecnico di Torino, Corso Duca degli Abruzzi 24, 10129 Torino (Italy)

    2007-02-15

    This work shows some of the results of a field study about environmental comfort investigations in classrooms. In this project thermal, acoustic, visual and air quality aspects were analysed in a number of classrooms-13 classrooms at four different high schools of the Provincia di Torino and four typical medium-sized university classrooms of the Politecnico di Torino, Italy. The investigations were carried out during the heating period. Both field measurements and subjective surveys were performed at the same time during the regular lesson periods. This paper focuses on thermal comfort, which may have a significant effect on the students' performance, in terms of attention, comprehension and learning levels. The measurement campaign consisted in measuring the thermal environment parameters-air temperature, mean radiant temperatures, air relative humidity and air velocity. Through these data, the thermal comfort Fanger's indices (predicted mean vote (PMV), and predicted percentage of dissatisfied (PPD)people) were calculated, the actual people clothing and metabolic rate being known. The subjective survey involved questions on the thermal environmental perception. They basically investigated the thermal environment acceptability and preference. Moreover, a judgement based on the typical seven point thermal sensation scale (Fanger 7-points scale) was also asked. Through the elaboration of the questionnaire data, the actual percentage of dissatisfied (PD) people of the felt thermal environment was evaluated. The judgements about the thermal environment were compared with the results of the field measurements. Moreover, the subjective mean votes were compared with the thermal environment perceptions in terms of acceptability and preference. (author)

  19. Robust Multilayered Encapsulation for High-Performance Triboelectric Nanogenerator in Harsh Environment.

    Science.gov (United States)

    Zheng, Qiang; Jin, Yiming; Liu, Zhuo; Ouyang, Han; Li, Hu; Shi, Bojing; Jiang, Wen; Zhang, Hao; Li, Zhou; Wang, Zhong Lin

    2016-10-03

    Harvesting biomechanical energy especially in vivo is of special significance for sustainable powering of wearable/implantable electronics. The triboelectric nanogenerator (TENG) is one of the most promising solutions considering its high efficiency, low cost, light weight, and easy fabrication, but its performance will be greatly affected if there is moisture or liquid leaked into the device when applied in vivo. Here, we demonstrate a multiple encapsulation process of the TENG to maintain its output performance in various harsh environments. Through systematic studies, the encapsulated TENG showed great reliability in humid or even harsh environment over 30 days with a stability index of more than 95%. Given its outstanding reliability, the TENG has the potential to be applied in variety of circumstances to function as a sustainable power source for self-powered biomedical electronics and environmental sensing systems.

  20. Development and Performance Verification of Fiber Optic Temperature Sensors in High Temperature Engine Environments

    Science.gov (United States)

    Adamovsky, Grigory; Mackey, Jeffrey R.; Kren, Lawrence A.; Floyd, Bertram M.; Elam, Kristie A.; Martinez, Martel

    2014-01-01

    A High Temperature Fiber Optic Sensor (HTFOS) has been developed at NASA Glenn Research Center for aircraft engine applications. After fabrication and preliminary in-house performance evaluation, the HTFOS was tested in an engine environment at NASA Armstrong Flight Research Center. The engine tests enabled the performance of the HTFOS in real engine environments to be evaluated along with the ability of the sensor to respond to changes in the engine's operating condition. Data were collected prior, during, and after each test in order to observe the change in temperature from ambient to each of the various test point levels. An adequate amount of data was collected and analyzed to satisfy the research team that HTFOS operates properly while the engine was running. Temperature measurements made by HTFOS while the engine was running agreed with those anticipated.

  1. Operational characterisation of requirements and early validation environment for high demanding space systems

    Science.gov (United States)

    Barro, E.; Delbufalo, A.; Rossi, F.

    1993-01-01

    The definition of some modern high demanding space systems requires a different approach to system definition and design from that adopted for traditional missions. System functionality is strongly coupled to the operational analysis, aimed at characterizing the dynamic interactions of the flight element with its surrounding environment and its ground control segment. Unambiguous functional, operational and performance requirements are to be defined for the system, thus improving also the successive development stages. This paper proposes a Petri Nets based methodology and two related prototype applications (to ARISTOTELES orbit control and to Hermes telemetry generation) for the operational analysis of space systems through the dynamic modeling of their functions and a related computer aided environment (ISIDE) able to make the dynamic model work, thus enabling an early validation of the system functional representation, and to provide a structured system requirements data base, which is the shared knowledge base interconnecting static and dynamic applications, fully traceable with the models and interfaceable with the external world.

  2. Entanglement dynamics of high-dimensional bipartite field states inside the cavities in dissipative environments

    Energy Technology Data Exchange (ETDEWEB)

    Tahira, Rabia; Ikram, Manzoor; Zubairy, M Suhail [Centre for Quantum Physics, COMSATS Institute of Information Technology, Islamabad (Pakistan); Bougouffa, Smail [Department of Physics, Faculty of Science, Taibah University, PO Box 30002, Madinah (Saudi Arabia)

    2010-02-14

    We investigate the phenomenon of sudden death of entanglement in a high-dimensional bipartite system subjected to dissipative environments with an arbitrary initial pure entangled state between two fields in the cavities. We find that in a vacuum reservoir, the presence of the state where one or more than one (two) photons in each cavity are present is a necessary condition for the sudden death of entanglement. Otherwise entanglement remains for infinite time and decays asymptotically with the decay of individual qubits. For pure two-qubit entangled states in a thermal environment, we observe that sudden death of entanglement always occurs. The sudden death time of the entangled states is related to the number of photons in the cavities, the temperature of the reservoir and the initial preparation of the entangled states.

  3. An Evolutionary Method for Financial Forecasting in Microscopic High-Speed Trading Environment

    Directory of Open Access Journals (Sweden)

    Chien-Feng Huang

    2017-01-01

    Full Text Available The advancement of information technology in financial applications nowadays have led to fast market-driven events that prompt flash decision-making and actions issued by computer algorithms. As a result, today’s markets experience intense activity in the highly dynamic environment where trading systems respond to others at a much faster pace than before. This new breed of technology involves the implementation of high-speed trading strategies which generate significant portion of activity in the financial markets and present researchers with a wealth of information not available in traditional low-speed trading environments. In this study, we aim at developing feasible computational intelligence methodologies, particularly genetic algorithms (GA, to shed light on high-speed trading research using price data of stocks on the microscopic level. Our empirical results show that the proposed GA-based system is able to improve the accuracy of the prediction significantly for price movement, and we expect this GA-based methodology to advance the current state of research for high-speed trading and other relevant financial applications.

  4. An Evolutionary Method for Financial Forecasting in Microscopic High-Speed Trading Environment

    Science.gov (United States)

    Li, Hsu-Chih

    2017-01-01

    The advancement of information technology in financial applications nowadays have led to fast market-driven events that prompt flash decision-making and actions issued by computer algorithms. As a result, today's markets experience intense activity in the highly dynamic environment where trading systems respond to others at a much faster pace than before. This new breed of technology involves the implementation of high-speed trading strategies which generate significant portion of activity in the financial markets and present researchers with a wealth of information not available in traditional low-speed trading environments. In this study, we aim at developing feasible computational intelligence methodologies, particularly genetic algorithms (GA), to shed light on high-speed trading research using price data of stocks on the microscopic level. Our empirical results show that the proposed GA-based system is able to improve the accuracy of the prediction significantly for price movement, and we expect this GA-based methodology to advance the current state of research for high-speed trading and other relevant financial applications. PMID:28316618

  5. Effect of high ambient temperature on behavior of sheep under semi-arid tropical environment

    Science.gov (United States)

    De, Kalyan; Kumar, Davendra; Saxena, Vijay Kumar; Thirumurugan, Palanisamy; Naqvi, Syed Mohammed Khursheed

    2017-07-01

    High environmental temperature is a major constraint in sheep production under semi-arid tropical environment. Behavior is the earliest indicator of animal's adaptation and responses to the environmental alteration. Therefore, the objective of this study was to assess the effects of high ambient temperature on the behavior of sheep under a semi-arid tropical environment. The experiment was conducted for 6 weeks on 16 Malpura cross (Garole × Malpura × Malpura (GMM)) rams. The rams were divided equally into two groups, designated as C and T. The rams of C were kept in comfortable environmental conditions served as control. The rams of T were exposed to a different temperature at different hours of the day in a climatic chamber, to simulate a high environmental temperature of summer in semi-arid tropic. The behavioral observations were taken by direct instantaneous observation at 15-min intervals for each animal individually. The feeding, ruminating, standing, and lying behaviors were recorded twice a week from morning (0800 hours) to afternoon (1700 hours) for 6 weeks. Exposure of rams to high temperature (T) significantly ( P animals of T spent significantly ( P behavior of sheep which is directed to circumvent the effect of the stressor.

  6. Hypersonic Engine Leading Edge Experiments in a High Heat Flux, Supersonic Flow Environment

    Science.gov (United States)

    Gladden, Herbert J.; Melis, Matthew E.

    1994-01-01

    A major concern in advancing the state-of-the-art technologies for hypersonic vehicles is the development of an aeropropulsion system capable of withstanding the sustained high thermal loads expected during hypersonic flight. Three aerothermal load related concerns are the boundary layer transition from laminar to turbulent flow, articulating panel seals in high temperature environments, and strut (or cowl) leading edges with shock-on-shock interactions. A multidisciplinary approach is required to address these technical concerns. A hydrogen/oxygen rocket engine heat source has been developed at the NASA Lewis Research Center as one element in a series of facilities at national laboratories designed to experimentally evaluate the heat transfer and structural response of the strut (or cowl) leading edge. A recent experimental program conducted in this facility is discussed and related to cooling technology capability. The specific objective of the experiment discussed is to evaluate the erosion and oxidation characteristics of a coating on a cowl leading edge (or strut leading edge) in a supersonic, high heat flux environment. Heat transfer analyses of a similar leading edge concept cooled with gaseous hydrogen is included to demonstrate the complexity of the problem resulting from plastic deformation of the structures. Macro-photographic data from a coated leading edge model show progressive degradation over several thermal cycles at aerothermal conditions representative of high Mach number flight.

  7. An Evolutionary Method for Financial Forecasting in Microscopic High-Speed Trading Environment.

    Science.gov (United States)

    Huang, Chien-Feng; Li, Hsu-Chih

    2017-01-01

    The advancement of information technology in financial applications nowadays have led to fast market-driven events that prompt flash decision-making and actions issued by computer algorithms. As a result, today's markets experience intense activity in the highly dynamic environment where trading systems respond to others at a much faster pace than before. This new breed of technology involves the implementation of high-speed trading strategies which generate significant portion of activity in the financial markets and present researchers with a wealth of information not available in traditional low-speed trading environments. In this study, we aim at developing feasible computational intelligence methodologies, particularly genetic algorithms (GA), to shed light on high-speed trading research using price data of stocks on the microscopic level. Our empirical results show that the proposed GA-based system is able to improve the accuracy of the prediction significantly for price movement, and we expect this GA-based methodology to advance the current state of research for high-speed trading and other relevant financial applications.

  8. Estimation of the uncertainty associated with the results based on the validation of chromatographic analysis procedures: application to the determination of chlorides by high performance liquid chromatography and of fatty acids by high resolution gas chromatography.

    Science.gov (United States)

    Quintela, M; Báguena, J; Gotor, G; Blanco, M J; Broto, F

    2012-02-03

    This article presents a model to calculate the uncertainty associated with an analytical result based on the validation of the analysis procedure. This calculation model is proposed as an alternative to commonly used bottom-up and top-down methods. This proposal is very advantageous as the validation of the procedures and the estimation of the uncertainty of the measurement are part of the technical requirements needed in order to obtain the ISO 17025:2005 accreditation. This model has been applied to the determination of chloride by liquid chromatography in lixiviates and in the determination of palmitic acid and stearic acid by gas chromatography in magnesium stearate samples.

  9. Impact of Maine's statewide nutrition policy on high school food environments.

    Science.gov (United States)

    Whatley Blum, Janet E; Beaudoin, Christina M; O'Brien, Liam M; Polacsek, Michele; Harris, David E; O'Rourke, Karen A

    2011-01-01

    We assessed the effect on the food environments of public high schools of Maine's statewide nutrition policy (Chapter 51), which banned "foods of minimal nutritional value" (FMNV) in public high schools that participated in federally funded meal programs. We documented allowable exceptions to the policy and describe the school food environments. We mailed surveys to 89 high school food-service directors to assess availability pre-Chapter 51 and post-Chapter 51 of soda, other sugar-sweetened beverages, and junk food. Frequency data were tabulated pre-Chapter 51 and post-Chapter 51, and Fisher exact test was used to assess significance in changes. We conducted food and beverage inventories at 11 high schools. The survey return rate was 61% (N = 54). Availability of soda in student vending significantly decreased pre-Chapter 51 versus post-Chapter 51 (P = .04). No significant changes were found for other sugar-sweetened beverages and junk food. Exceptions to Chapter 51 were permitted to staff (67%), to the public (86%), and in career and technical education programs (31%). Inventories in a subset of schools found no availability of soda for students, whereas other sugar-sweetened beverages and junk food were widely available in à la carte, vending machines, and school stores. Candy, considered a FMNV, was freely available. Soda advertisement on school grounds was common. Student vending choices improved after the implementation of Chapter 51; however, use of FMNV as the policy standard may be limiting, as availability of other sugar-sweetened beverages and junk food was pervasive. School environments were not necessarily supportive of the policy, as advertisement of soda was common and some FMNV were available. Furthermore, local exceptions to Chapter 51 likely reduced the overall effect of the policy.

  10. Lubiprostone: a chloride channel activator.

    Science.gov (United States)

    Lacy, Brian E; Levy, L Campbell

    2007-04-01

    In January 2006 the Food and Drug Administration approved lubiprostone for the treatment of chronic constipation in men and women aged 18 and over. Lubiprostone is categorized as a prostone, a bicyclic fatty acid metabolite of prostaglandin E1. Lubiprostone activates a specific chloride channel (ClC-2) in the gastrointestinal (GI) tract to enhance intestinal fluid secretion, which increases GI transit and improves symptoms of constipation. This article reviews the role of chloride channels in the GI tract, describes the structure, function, and pharmacokinetics of lubiprostone, and discusses clinically important data on this new medication.

  11. Development of an Instrument for Assessing Senior High School Students' Preferred and Perceived Laboratory Classroom Environment

    Science.gov (United States)

    Hsiao, Chien-Hua; Wu, Ying-Tien; Lin, Chung-Yen; Wong, Terrence William; Fu, Hsieh-Hai; Yeh, Ting-Kuang; Chang, Chung-Yen

    2014-01-01

    This study aimed to develop an instrument, named the inquiry-based laboratory classroom environment instrument (ILEI), for assessing senior high-school science students' preferred and perceived laboratory environment. A total of 262 second-year students, from a senior-high school in Taiwan, were recruited for this study. Four stages were…

  12. Mechanism of chloride interaction with neurotransmitter:sodium symporters.

    Science.gov (United States)

    Zomot, Elia; Bendahan, Annie; Quick, Matthias; Zhao, Yongfang; Javitch, Jonathan A; Kanner, Baruch I

    2007-10-11

    Neurotransmitter:sodium symporters (NSS) have a critical role in regulating neurotransmission and are targets for psychostimulants, anti-depressants and other drugs. Whereas the non-homologous glutamate transporters mediate chloride conductance, in the eukaryotic NSS chloride is transported together with the neurotransmitter. In contrast, transport by the bacterial NSS family members LeuT, Tyt1 and TnaT is chloride independent. The crystal structure of LeuT reveals an occluded binding pocket containing leucine and two sodium ions, and is highly relevant for the neurotransmitter transporters. However, the precise role of chloride in neurotransmitter transport and the location of its binding site remain elusive. Here we show that introduction of a negatively charged amino acid at or near one of the two putative sodium-binding sites of the GABA (gamma-aminobutyric acid) transporter GAT-1 from rat brain (also called SLC6A1) renders both net flux and exchange of GABA largely chloride independent. In contrast to wild-type GAT-1, a marked stimulation of the rate of net flux, but not of exchange, was observed when the internal pH was lowered. Equivalent mutations introduced in the mouse GABA transporter GAT4 (SLC6A11) and the human dopamine transporter DAT (SLC6A3) also result in chloride-independent transport, whereas the reciprocal mutations in LeuT and Tyt1 render substrate binding and/or uptake by these bacterial NSS chloride dependent. Our data indicate that the negative charge, provided either by chloride or by the transporter itself, is required during binding and translocation of the neurotransmitter, probably to counterbalance the charge of the co-transported sodium ions.

  13. 氯盐环境中新型合金耐蚀钢筋Cr10Mo1的钝化行为%Passive Behavior of New Alloy Corrosion Resistant Steel Cr10Mo1 in Chloride-containing Environment

    Institute of Scientific and Technical Information of China (English)

    艾志勇; 孙伟; 蒋金洋; 麻晗; 张建春; 宋丹

    2016-01-01

    concentration is above a certain level.Cr oxides,as the key components which just make the differences between the passive films on the alloy corrosion-resistant steel and plain carbon steel,can still remain stable and maintain the good density and integrity of the passive layer on the alloy corrosion-resistant steel under high chlorides concentration, which provides the alloy corrosion-resistant steel favorable passivation performance.

  14. Endocytic proteins drive vesicle growth via instability in high membrane tension environment

    CERN Document Server

    Walani, Nikhil; Agrawal, Ashutosh

    2015-01-01

    Clathrin-mediated endocytosis (CME) is a key pathway for transporting cargo into cells via membrane vesicles. It plays an integral role in nutrient import, signal transduction, neurotransmission and cellular entry of pathogens and drug-carrying nanoparticles. As CME entails substantial local remodeling of the plasma membrane, the presence of membrane tension offers resistance to bending and hence, vesicle formation. Experiments show that in such high tension conditions, actin dynamics is required to carry out CME successfully. In this study, we build upon these pioneering experimental studies to provide fundamental mechanistic insights into the roles of two key endocytic proteins, namely, actin and BAR proteins in driving vesicle formation in high membrane tension environment. Our study reveals a new actin force induced `snap-through instability' that triggers a rapid shape transition from a shallow invagination to a highly invaginated tubular structure. We show that the association of BAR proteins stabilizes...

  15. Anthropometric database for the learning environment of high school and university students.

    Science.gov (United States)

    Dawal, Siti Zawiah; Zadry, Hilma Raimona; Azmi, Sharifah Nadya Syed; Rohim, Siti Rusyida; Sartika, Sari Julia

    2012-01-01

    This paper presents an anthropometric database of high school and university students from Kuala Lumpur, Malaysia. Forty-one high school participants (21 males and 20 females), 13-17 years old, and 143 university students (74 males and 69 females) took part in the study. Twenty-one static body dimensions were measured. The greatest mean differences in the anthropometric data between male and female high school students were found in the sitting elbow height. In addition, a comparison of anthropometric data of male and female university students showed that data for males and females were significantly different, except for buttock-popliteal length, sitting elbow height and thigh clearance. The primary aim of this study was to develop an anthropometric database that could be used as a primary reference in designing products, devices and equipment for ergonomic learning environments.

  16. Dealing Collectively with Critical Incident Stress Reactions in High Risk Work Environments

    DEFF Research Database (Denmark)

    Müller-Leonhardt, Alice; Strøbæk, Pernille Solveig; Vogt, joachim

    2015-01-01

    aim of this paper is to shift the representation of coping patterns within high risk occupations to an existential part of cultural pattern and social structure, which characterises high reliability organisations. Drawing upon the specific peer model of critical incident stress management (CISM......), in which qualified operational peers support colleagues who experienced critical incident stress, the paper discusses critical incident stress management in air traffic control. Our study revealed coping patterns that co-vary with the culture that the CISM programme fostered within this specific high...... organisations. Indeed, we found that the CISM programme once integrated within the socio-cultural patterns of this specific working environment enhanced not only individual feelings of being supported but also organisational safety culture. Keywords: coping; safety culture; critical incident stress management...

  17. Ubiquitous Green Computing Techniques for High Demand Applications in Smart Environments

    Directory of Open Access Journals (Sweden)

    Jose M. Moya

    2012-08-01

    Full Text Available Ubiquitous sensor network deployments, such as the ones found in Smart cities and Ambient intelligence applications, require constantly increasing high computational demands in order to process data and offer services to users. The nature of these applications imply the usage of data centers. Research has paid much attention to the energy consumption of the sensor nodes in WSNs infrastructures. However, supercomputing facilities are the ones presenting a higher economic and environmental impact due to their very high power consumption. The latter problem, however, has been disregarded in the field of smart environment services. This paper proposes an energy-minimization workload assignment technique, based on heterogeneity and application-awareness, that redistributes low-demand computational tasks from high-performance facilities to idle nodes with low and medium resources in the WSN infrastructure. These non-optimal allocation policies reduce the energy consumed by the whole infrastructure and the total execution time.

  18. Ubiquitous green computing techniques for high demand applications in Smart environments.

    Science.gov (United States)

    Zapater, Marina; Sanchez, Cesar; Ayala, Jose L; Moya, Jose M; Risco-Martín, José L

    2012-01-01

    Ubiquitous sensor network deployments, such as the ones found in Smart cities and Ambient intelligence applications, require constantly increasing high computational demands in order to process data and offer services to users. The nature of these applications imply the usage of data centers. Research has paid much attention to the energy consumption of the sensor nodes in WSNs infrastructures. However, supercomputing facilities are the ones presenting a higher economic and environmental impact due to their very high power consumption. The latter problem, however, has been disregarded in the field of smart environment services. This paper proposes an energy-minimization workload assignment technique, based on heterogeneity and application-awareness, that redistributes low-demand computational tasks from high-performance facilities to idle nodes with low and medium resources in the WSN infrastructure. These non-optimal allocation policies reduce the energy consumed by the whole infrastructure and the total execution time.

  19. Evidence of a high density population of harvested leopards in a montane environment.

    Directory of Open Access Journals (Sweden)

    Julia N Chase Grey

    Full Text Available Populations of large carnivores can persist in mountainous environments following extensive land use change and the conversion of suitable habitat for agriculture and human habitation in lower lying areas of their range. The significance of these populations is poorly understood, however, and little attention has focussed on why certain mountainous areas can hold high densities of large carnivores and what the conservation implications of such populations might be. Here we use the leopard (Panthera pardus population in the western Soutpansberg Mountains, South Africa, as a model system and show that montane habitats can support high numbers of leopards. Spatially explicit capture-recapture (SECR analysis recorded the highest density of leopards reported outside of state-protected areas in sub-Saharan Africa. This density represents a temporally high local abundance of leopards and we explore the explanations for this alongside some of the potential conservation implications.

  20. Inelastic deformation behavior of thermal barrier coatings exposed at a high-temperature environment

    Directory of Open Access Journals (Sweden)

    Arai M.

    2010-06-01

    Full Text Available Thermal barrier coatings (TBCs are usually deposited onto the surface of the high-temperature component such as gas turbine, in order to protect it from a hightemperature environment. Coating stress generated by such a high-temperature brings serious damages in TBCs in service. For predicting numerically it, it is necessary to develop the constitutive equation suite to plasam-sprayed TBCs. Previous studies have made clear that the freestanding ceramic coat peeled from TBC coated substrate deforms nonlinearly with a mechanical loading, however the results there have been restricted to the test done using as-sprayed sample. In this study, effect of deposition parameter and high-temperature exposure condition on stress-strain curve of the freestanding ceramic coating sample was examined. The associated deformation process was discussed with the microstructure changes observed after performing a bending test for the exposed sample.

  1. Dinosaurs on the North Slope, Alaska: High latitude, latest cretaceous environments

    Science.gov (United States)

    Brouwers, E.M.; Clemens, W.A.; Spicer, R.A.; Ager, T.A.; Carter, L.D.; Sliter, W.V.

    1987-01-01

    Abundant skeletal remains demonstrate that lambeosaurine hadrosaurid, tyrannosaurid, and troodontid dinosaurs lived on the Alaskan North Slope during late Campanian-early Maestrichtian time (about 66 to 76 million years ago) in a deltaic environment dominated by herbaceous vegetation. The high ground terrestrial plant community was a mild- to cold-temperate forest composed of coniferous and broad leaf trees. The high paleolatitude (about 70?? to 85?? North) implies extreme seasonal variation in solar insolation, temperature, and herbivore food supply. Great distances of migration to contemporaneous evergreen floras and the presence of both juvenile and adult hadrosaurs suggest that they remained at high latitudes year-round. This challenges the hypothesis that short-term periods of darkness and temperature decrease resulting from a bolide impact caused dinosaurian extinction.

  2. Understanding Fundamental Material Degradation Processes in High Temperature Aggressive Chemomechanical Environments

    Energy Technology Data Exchange (ETDEWEB)

    Stubbins, James; Gewirth, Andrew; Sehitoglu, Huseyin; Sofronis, Petros; Robertson, Ian

    2014-01-16

    The objective of this project is to develop a fundamental understanding of the mechanisms that limit materials durability for very high-temperature applications. Current design limitations are based on material strength and corrosion resistance. This project will characterize the interactions of high-temperature creep, fatigue, and environmental attack in structural metallic alloys of interest for the very high-temperature gas-cooled reactor (VHTR) or Next–Generation Nuclear Plant (NGNP) and for the associated thermo-chemical processing systems for hydrogen generation. Each of these degradation processes presents a major materials design challenge on its own, but in combination, they can act synergistically to rapidly degrade materials and limit component lives. This research and development effort will provide experimental results to characterize creep-fatigue-environment interactions and develop predictive models to define operation limits for high-temperature structural material applications. Researchers will study individually and in combination creep-fatigue-environmental attack processes in Alloys 617, 230, and 800H, as well as in an advanced Ni-Cr oxide dispersion strengthened steel (ODS) system. For comparison, the study will also examine basic degradation processes in nichrome (Ni-20Cr), which is a basis for most high-temperature structural materials, as well as many of the superalloys. These materials are selected to represent primary candidate alloys, one advanced developmental alloy that may have superior high-temperature durability, and one model system on which basic performance and modeling efforts can be based. The research program is presented in four parts, which all complement each other. The first three are primarily experimental in nature, and the last will tie the work together in a coordinated modeling effort. The sections are (1) dynamic creep-fatigue-environment process, (2) subcritical crack processes, (3) dynamic corrosion – crack

  3. Depth imaging in highly scattering underwater environments using time-correlated single-photon counting

    Science.gov (United States)

    Maccarone, Aurora; McCarthy, Aongus; Halimi, Abderrahim; Tobin, Rachael; Wallace, Andy M.; Petillot, Yvan; McLaughlin, Steve; Buller, Gerald S.

    2016-10-01

    This paper presents an optical depth imaging system optimized for highly scattering environments such as underwater. The system is based on the time-correlated single-photon counting (TCSPC) technique and the time-of-flight approach. Laboratory-based measurements demonstrate the potential of underwater depth imaging, with specific attention given to environments with a high level of scattering. The optical system comprised a monostatic transceiver unit, a fiber-coupled supercontinuum laser source with a wavelength tunable acousto-optic filter (AOTF), and a fiber-coupled single-element silicon single-photon avalanche diode (SPAD) detector. In the optical system, the transmit and receive channels in the transceiver unit were overlapped in a coaxial optical configuration. The targets were placed in a 1.75 meter long tank, and raster scanned using two galvo-mirrors. Laboratory-based experiments demonstrate depth profiling performed with up to nine attenuation lengths between the transceiver and target. All of the measurements were taken with an average laser power of less than 1mW. Initially, the data was processed using a straightforward pixel-wise cross-correlation of the return timing signal with the system instrumental timing response. More advanced algorithms were then used to process these cross-correlation results. These results illustrate the potential for the reconstruction of images in highly scattering environments, and to permit the investigation of much shorter acquisition time scans. These algorithms take advantage of the data sparseness under the Discrete Cosine Transform (DCT) and the correlation between adjacent pixels, to restore the depth and reflectivity images.

  4. Corrosion Rate of Hydrogenation to C110 Casing in High H2S Environment

    Institute of Scientific and Technical Information of China (English)

    ZHANG Zhi; LI Changjin; ZHANG Jiyin; SHI Taihe

    2012-01-01

    The corrosion behavior of C110 bushing at high temperature and high pressure with a high H2S / CO2 was studied,and a basis for the materials selection of sour gas well bushing was provided in H2S,CO2 and saline coexisting environment.Under acidic condiction,hydrogen atoms greatly entered into the material and caused the material properties changed.Weight loss method was used to study the corrosion rate of hydrogen charging samples and original untreated samples in simulated oil field environment.PAR2273 electrochemical workstation was used to examine the electrochemical performance of samples untreated,hydrogen charging after reacting in autoclave.The corrosion product film was observed through SEM.The experimental results show that sample with hydrogen charging has a much more obvious partial corrosion and pitting corrosion than the untreated blank sample even the downhole corrosion speed of bushing is increased after being used for a period of time.Polarization curve shows the corrosion tendency is the same between sample with or without hydrogen charging and corrosion tendency is reduced by corrosion product film.A layer of dense product film formed on the surface of samples provides a certain protective effect to the matrix,but cracked holes which will accelerate partial corrosion of the sample were also observed.

  5. An investigation of community noise in high-rise residential environments.

    Science.gov (United States)

    Alam, Sheikh Mahbub; Eang, Lee Siew; Tan, Alan; Tiong, Tan Sze

    2010-06-01

    High-rise dwellers in Singapore are often subjected to several community noise sources in close proximity. These include food center, children playground, soccer playground, basketball playground, waste disposal truck, etc. A scientific and reliable approach is required for evaluation of the community noise and its impact on high-rise dwellers. A comprehensive noise survey by a cluster sampling technique, conducted among 522 households in five residential towns in Singapore, showed that community noise was one of the prime sources of noise in a high-rise residential environment. From a subjective noise survey, undertaken concurrent with objective noise measurements, a mean outdoor noise level of 59 dBA was established as an acceptable noise level in the indoor environment. To investigate the level of noise exposure from different community noise sources, software modeling and simulations were carried out. The predicted results were validated with field measured data at five 16 story residential buildings. Analysis of noise exposure data showed that except for waste disposal truck, noise exposure due to other community noise sources (building distance of 15 m) were within the established acceptable noise level. A factor analysis of the survey data identified the key factors related to the disturbance due to community noise sources.

  6. Propagation of high-power partially coherent fibre laser beams in a real environment

    Institute of Scientific and Technical Information of China (English)

    Tao Ru-Mao; Si Lei; Ma Yan-Xing; Zou Yong-Chao; Zhou Pu

    2011-01-01

    The propagation performance of high-power partially coherent fibre laser beams in a real environment is investigated and the theoretical model of a high-power fibre laser propagating in a real environment is established. The influence of a collimating system and thermal blooming is considered together with atmospheric turbulence and mechanical jitter. The laser energy concentration of partially coherent beams in the far field is calculated and analysed based on the theoretical model. It is shown that the propagation performance of partially coherent beams depends on the collimating system,atmospheric turbulence,mechanical jitter and thermal blooming. The propagation performance of partially coherent beams and fully coherent beams is studied and the results show that partially coherent beams are less sensitive to the influence of thermal blooming,which results in that the energy degeneration for partially coherent beams is only 50%a of that for fully coherent beams. Both partially coherent beams and fully coherent beams become less sensitive to thermal blooming when the average structural constant of the refraction index fluctuations increases to 1.7x10-14 m-2/3. The investigation presents a reference for applications of a high-power fibre laser system.

  7. Exploring the Potential of Aerial Photogrammetry for 3d Modelling of High-Alpine Environments

    Science.gov (United States)

    Legat, K.; Moe, K.; Poli, D.; Bollmannb, E.

    2016-03-01

    High-alpine areas are subject to rapid topographic changes, mainly caused by natural processes like glacial retreat and other geomorphological processes, and also due to anthropogenic interventions like construction of slopes and infrastructure in skiing resorts. Consequently, the demand for highly accurate digital terrain models (DTMs) in alpine environments has arisen. Public administrations often have dedicated resources for the regular monitoring of glaciers and natural hazard processes. In case of glaciers, traditional monitoring encompasses in-situ measurements of area and length and the estimation of volume and mass changes. Next to field measurements, data for such monitoring programs can be derived from DTMs and digital ortho photos (DOPs). Skiing resorts, on the other hand, require DTMs as input for planning and - more recently - for RTK-GNSS supported ski-slope grooming. Although different in scope, the demand of both user groups is similar: high-quality and up-to-date terrain data for extended areas often characterised by difficult accessibility and large elevation ranges. Over the last two decades, airborne laser scanning (ALS) has replaced photogrammetric approaches as state-of-the-art technology for the acquisition of high-resolution DTMs also in alpine environments. Reasons include the higher productivity compared to (manual) stereo-photogrammetric measurements, canopy-penetration capability, and limitations of photo measurements on sparsely textured surfaces like snow or ice. Nevertheless, the last few years have shown strong technological advances in the field of aerial camera technology, image processing and photogrammetric software which led to new possibilities for image-based DTM generation even in alpine terrain. At Vermessung AVT, an Austrian-based surveying company, and its subsidiary Terra Messflug, very promising results have been achieved for various projects in high-alpine environments, using images acquired by large-format digital

  8. The inner environment of Z~CMa: High-Contrast Imaging Polarimetry with NaCo

    CERN Document Server

    Canovas, H; Dougados, C; de Boer, J; Ménard, F; Casassus, S; Schreiber, M R; Cieza, L A; Caceres, C; Girard, J H

    2015-01-01

    Context. Z\\,CMa is a binary composed of an embedded Herbig Be and an FU Ori class star separated by $\\sim100$ au. Observational evidence indicate a complex environment in which each star has a circumstellar disk and drives a jet, and the whole system is embedded in a large dusty envelope. Aims. We aim to probe the circumbinary environment of Z\\,CMa in the inner 400 au in scattered light. Methods. We use high contrast imaging polarimetry with VLT/NaCo at $H$ and $K_s$ bands. Results. The central binary is resolved in both bands. The polarized images show three bright and complex structures: a common dust envelope, a sharp extended feature previously reported in direct light, and an intriguing bright clump located $0\\farcs3$ south of the binary, which appears spatially connected to the sharp extended feature. Conclusions.We detect orbital motion when compared to previous observations, and report a new outburst driven by the Herbig star. Our observations reveal the complex inner environment of Z\\,CMa with unprec...

  9. The evaluation of different environments in ultra-high frequency induction sintered powder metal compacts

    Directory of Open Access Journals (Sweden)

    Sari Çavdar, Pınar

    2015-03-01

    Full Text Available The application of the iron based Powder Metal (PM compacts in Ultra-High Frequency Induction Sintering (UHFIS was reviewed for different environments. The three different environments: atmosphere, argon and vacuum were applied to the PM compacts. Iron based PM compacts were sintered at 1120 °C for a total of 550 seconds by using induction sintering machines with 2.8 kW power and 900 kHz frequency. Micro structural properties, densities, roughness and micro hardness values were obtained for all environments. The results were compared with each other.Este trabajo comprende una revisión de la aplicación de la inducción de ultra-alta frecuencia (UHFIS en la sinterización de aleaciones pulvimetalúrgicas de base hierro para diferentes ambientes. Los tres ambientes estudiados son: atmósfera, argón y vacío aplicados a material ya consolidado. Aleaciones base hierro ya compactadas se sinterizan a temperaturas de 1120 °C durante 550 segundos por medio de máquinas de sinterizado por inducción de potencia de 2,8 kW y 900 kHz de frecuencia. Se compararán las propiedades microestructurales, y los valores obtenidos de densidad, rugosidad y microdureza para todos los ambientes estudiados.

  10. Integrating INIS into a high energy physics information environment thoughts from CERN

    CERN Document Server

    Yeomans, Joanne; Baudic, Romain; Picchioli, Ingrid; International Conference on Nuclear Knowledge Management : Strategies, Information Management and Human Resource Development. Special Session : The Role of INIS in Knowledge Preservation

    2004-01-01

    Information searchers from the high energy physics community expect an integrated information environment. The CERN Library offers its print and electronic collections through a combined Web interface and maintains the database by semi-automated processes to upload bibliographic and full-text records. Suggestions are offered by which INIS could develop its own Web interface and better match HEP users’ expectations. These include implementing full-text linking, increasing currency, expanding search and display functions and developing the richness of the data. Links with the National Nuclear Data Center and Crossref could also increase its visibility.

  11. Programming Environment for a High-Performance Parallel Supercomputer with Intelligent Communication

    Directory of Open Access Journals (Sweden)

    A. Gunzinger

    1996-01-01

    Full Text Available At the Electronics Laboratory of the Swiss Federal Institute of Technology (ETH in Zürich, the high-performance parallel supercomputer MUSIC (MUlti processor System with Intelligent Communication has been developed. As applications like neural network simulation and molecular dynamics show, the Electronics Laboratory supercomputer is absolutely on par with those of conventional supercomputers, but electric power requirements are reduced by a factor of 1,000, weight is reduced by a factor of 400, and price is reduced by a factor of 100. Software development is a key issue of such parallel systems. This article focuses on the programming environment of the MUSIC system and on its applications.

  12. Possibility of Using Moringa Peregrina Seeds Compared with Alum and Poly Aluminum Chloride in Sewage Treatment

    Directory of Open Access Journals (Sweden)

    E Olyaie

    2010-10-01

    Full Text Available "n "n "nBackgrounds and Objective: In arid and semi-arid regions of the world, urban runoff as a source of water restoration and is considered valuable. Wastewater treatment, while preserving the environment, it can be considered as water source. The aim of this study to evaluate the possibility of using powder grain Peregrina in wastewater treatment in comparing with Alum and PloyAluminum Chloride (PAC. "nMaterials and Methods: Flocculation and coagulation tests were done by Jar test. Wastewater quality parameters were measured according to standard method."nResults: Studies have been showed that in optimum Peregrina concentration, efficiency of turbidity reduction, total hardness, calcium hardness, magnesium hardness, total E. Coli are 95.11, 38, 55.5, 46.6, 97 and 97 percent respectively. It is noted that turbidity reducing directly related with coli form reduction. As, with increasing turbidity reduction, coliform reduction is increased. The most reduction of E. coli with combination of Alum, Ploy Aluminum Chloride and Peregrina was 100 percent. In optimum concentration of Alum, Ploy Aluminum Chloride and Peregrina, the quality of treated wastewater would be in the range of environmental standards. Therefore, treated wastewater can be entering to surface water and reuse as irrigation water."nConclusion: The results derived from this study showed that the treated wastewater can be use in a variety of irrigation except sprinkler irrigation due to burn the leaves of plants. (high electrical conductivity.Also, the low cost of seed Peregrina and good performance in the refining operations, it is suggested that Peregrina as a replacement for poly aluminum chloride and an alum to be used for wastewater treatment.

  13. Quantitative determination of the macrolide antibiotics erythromycin, roxithromycin, azithromycin and clarithromycin in human serum by high-performance liquid chromatography using pre-column derivatization with 9-fluorenylmethyloxycarbonyl chloride and fluorescence detection.

    Science.gov (United States)

    Sastre Toraño, J; Guchelaar, H J

    1998-12-11

    A validated, highly sensitive and precise high-performance liquid chromatographic (HPLC) method for the determination of the macrolides erythromycin, azithromycin, clarithromycin and roxithromycin in human serum is described. A diethyl ether extract, obtained from serum using a saturated sodium carbonate solution, was treated with 9-fluorenylmethyl-oxycarbonyl chloride (FMOC-Cl) for 40 min at 40 degrees C and chromatographed on a base-deactivated octadecyl column, maintained at 50 degrees C during elution, using an eluent composed of acetonitrile-hydrogenphosphate buffer, pH 7.5, with 0.125% triethylamine (3:2, v/v). Fluorescence detection was used at an excitation wavelength of 255 nm and an emission wavelength of 315 nm. Erythromycin, clarithromycin, roxithromycin and azithromycin were found to have retention times of 8.8, 15.7, 17.1 and 20.7 min, respectively. Recoveries ranging from 93 to 104% were found with reproducibility coefficients of variation of 1.1-5%. Mean correlation coefficients of 0.9997, 0.9998, 0.9996 and 0.9994 were found for the linear calibration curves (n = 2) of erythromycin (0.320-16.1 mg/l), roxithromycin (3.24-19.4 mg/l), clarithromycin (0.190-19.4 mg/l) and azithromycin (0.0988-4.94 mg/l), respectively.

  14. Geophysical and geochemical characterization and delineation of a crude oil spill in a highly saline environment

    Science.gov (United States)

    Ross, Cameron Stuart

    Geophysical and geochemical methods were used at Grand Terre 1 (GT1) Island off the coast of Louisiana, an island that had been heavily contaminated with crude oil associated with the April 2010 BP Deepwater Horizon oil spill. Electrical methods and aqueous geochemistry have proven sensitive in the detection of contaminates, as well as the biological and chemical processes associated with the biodegradation of hydrocarbons in the subsurface. However, to the author's knowledge, all of these studies have dealt with mature (or aged) spills within a freshwater environment. The BP Deepwater Horizon oil spill therefor provided a unique opportunity to not only use traditional geophysical and geochemical methods to characterize and delineate fresh crude oil in a highly saline environment and to capture the early time biogeophysical signals resulting from the physical, chemical, and microbial transformation of crude oil in a highly saline environment. Electrical resistivity and electromagnetic methods were used. Barometric pressure, temperature, electrical conductivity, and water level values for the shallow groundwater were continuously logged. Geochemical analysis was performed on water samples collected from piezometers networks installed in the impacted, transitional, and background areas. Sediment cores were retrieved throughout the site and used for grain size analysis, magnetic susceptibility, total organic and inorganic carbon, and x-ray fluorescence. Soil samples were collected for microbial analyses from the impacted and background areas. Microcosms were set up to determine the microbial diversity analysis was used to determine microbial community composition, and biodegradation potential of indigenous populations. Based on the geochemical, microbial, and soil analysis, the relatively higher apparent resistivity anomaly observed between the depths of 0.20 m to 1.20 m bgs could be explained by two scenarios(1): elevated resistivity was caused by gas in the

  15. Chloride : The queen of electrolytes?

    NARCIS (Netherlands)

    Berend, Kenrick; van Hulsteijn, Leonard Hendrik; Gans, Rijk O. B.

    2012-01-01

    Background: Channelopathies, defined as diseases that are caused by mutations in genes encoding ion channels, are associated with a wide variety of symptoms and have been documented extensively over the past decade. In contrast, despite the important role of chloride in serum, textbooks in general d

  16. 1,5-Diaminotetrazolium chloride

    Directory of Open Access Journals (Sweden)

    Ling-Qiao Meng

    2010-04-01

    Full Text Available The title compound, CH5N6+·Cl−, crystallized with two indepedent 1,5-diaminotetrazolium cations and two independent chloride anions in the asymmetric unit. In the crystal, there are a number of N—H...Cl hydrogen-bonding interactions, which generate a three-dimensional network.

  17. [Headspace GC/MS analysis of residual vinyl chloride and vinylidene chloride in polyvinyl chloride and polyvinylidene chloride products].

    Science.gov (United States)

    Ohno, Hiroyuki; Mutsuga, Motoh; Kawamura, Yoko; Suzuki, Masako; Aoyama, Taiki

    2005-02-01

    A headspace GC/MS analysis method for the simultaneous determination of residual vinyl chloride (VC) and vinylidene chloride (VDC) in polyvinyl chloride (PVC) and polyvinylidene chloride (PVDC) products was developed. A test sample was swelled overnight with N,N-dimethylacetamide in a sealed vial. The vial was incubated for 1 hour at 90 degrees C, then the headspace gas was analyzed by GC/MS using a PLOT capillary column. The recoveries from spiked PVC and PVDC samples were 90.0-112.3% for VC and 85.2-108.3% for VDC. The determination limits were 0.01 microg/g for VC and 0.06/microg/g for VDC, respectively. By this method, VC was detected in two PVC water supply pipes at the levels of 0.61 and 0.01 microg/g. On the other hand, VC and VDC were not detected in any of the food container-packages or toys tested.

  18. Germination of Spores of Astrobiologically Relevant Bacillus Species in High-Salinity Environments

    Science.gov (United States)

    Nagler, Katja; Julius, Christina; Moeller, Ralf

    2016-07-01

    In times of increasing space exploration and search for extraterrestrial life, new questions and challenges for planetary protection, aiming to avoid forward contamination of different planets or moons with terrestrial life, are emerging. Spore-forming bacteria such as Bacillus species have a high contamination potential due to their spores' extreme resistance, enabling them to withstand space conditions. Spores require liquid water for their conversion into a growing cell (i.e., spore germination and subsequent growth). If present, water on extraterrestrial planets or moons is likely to be closely associated with salts (e.g., in salty oceans or brines), thus constituting high-salinity environments. Spores of Bacillus subtilis can germinate despite very high salt concentrations, although salt stress does exert negative effects on this process. In this study, germination and metabolic reactivation ("outgrowth") of spores of five astrobiologically relevant Bacillus species (B. megaterium, B. pumilus SAFR-032, B. nealsonii, B. mojavensis, and B. vallismortis) in high salinity (≤3.6 M NaCl) were investigated. Spores of different species exhibited different germination and outgrowth capabilities in high salinity, which strongly depended on germination conditions, especially the exact composition of the medium. In this context, a new "universal" germination trigger for Bacillus spores, named KAGE (KCl, L-alanine, D-glucose, ectoine), was identified, which will be very useful for future comparative germination and outgrowth studies on different Bacillus species. Overall, this study yielded interesting new insights on salt stress effects on spore germination and points out the difficulty of predicting the potential of spores to contaminate salty environments on extraterrestrial celestial bodies.

  19. High affinity and temperature sensitivity of blood oxygen binding in Pangasianodon hypophthalmus due to lack of chloride-hemoglobin allosteric interaction.

    Science.gov (United States)

    Damsgaard, Christian; Phuong, Le My; Huong, Do Thi Thanh; Jensen, Frank B; Wang, Tobias; Bayley, Mark

    2015-06-01

    Air-breathing fishes represent interesting organisms in terms of understanding the physiological changes associated with the terrestrialization of vertebrates, and, further, are of great socio-economic importance for aquaculture in Southeast Asia. To understand how environmental factors, such as high temperature, affect O2 transport in air-breathing fishes, this study assessed the effects of temperature on O2 binding of blood and Hb in the economically important air-breathing fish Pangasianodon hypophthalmus. To determine blood O2 binding properties, blood was drawn from resting cannulated fishes and O2 binding curves made at 25°C and 35°C. To determine the allosteric regulation and thermodynamics of Hb O2 binding, Hb was purified, and O2 equilibria were recorded at five temperatures in the absence and presence of ATP and Cl(-). Whole blood had a high O2 affinity (O2 tension at half saturation P50 = 4.6 mmHg at extracellular pH 7.6 and 25°C), a high temperature sensitivity of O2 binding (apparent heat of oxygenation ΔH(app) = -28.3 kcal/mol), and lacked a Root effect. Further, the data on Hb revealed weak ATP binding and a complete lack of Cl(-) binding to Hb, which, in part, explains the high O2 affinity and high temperature sensitivity of blood O2 binding. This study demonstrates how a potent mechanism for increasing O2 affinity is linked to increased temperature sensitivity of O2 transport and provides a basic framework for a better understanding of how hypoxia-adapted species will react to increasing temperatures.

  20. 21 CFR 173.375 - Cetylpyridinium chloride.

    Science.gov (United States)

    2010-04-01

    ... CONSUMPTION Specific Usage Additives § 173.375 Cetylpyridinium chloride. Cetylpyridinium chloride (CAS Reg. No... Nutrition's Library, Food and Drug Administration, 5100 Paint Branch Pkwy., College Park, MD 20740, or...

  1. In-depth analysis of chloride treatments for thin-film CdTe solar cells

    OpenAIRE

    Major, J.D.; Al Turkestani, M.; Bowen, L; Brossard, M.; Li, C; Lagoudakis, P.; S. J. Pennycook; Phillips, L. J.; Treharne, R. E.; Durose, K.

    2016-01-01

    CdTe thin-film solar cells are now the main industrially established alternative to silicon-based photovoltaics. These cells remain reliant on the so-called chloride activation step in order to achieve high conversion efficiencies. Here, by comparison of effective and ineffective chloride treatments, we show the main role of the chloride process to be the modification of grain boundaries through chlorine accumulation, which leads an increase in the carrier lifetime. It is also demonstrated th...

  2. Path Planning for Non-Circular, Non-Holonomic Robots in Highly Cluttered Environments.

    Science.gov (United States)

    Samaniego, Ricardo; Lopez, Joaquin; Vazquez, Fernando

    2017-08-15

    This paper presents an algorithm for finding a solution to the problem of planning a feasible path for a slender autonomous mobile robot in a large and cluttered environment. The presented approach is based on performing a graph search on a kinodynamic-feasible lattice state space of high resolution; however, the technique is applicable to many search algorithms. With the purpose of allowing the algorithm to consider paths that take the robot through narrow passes and close to obstacles, high resolutions are used for the lattice space and the control set. This introduces new challenges because one of the most computationally expensive parts of path search based planning algorithms is calculating the cost of each one of the actions or steps that could potentially be part of the trajectory. The reason for this is that the evaluation of each one of these actions involves convolving the robot's footprint with a portion of a local map to evaluate the possibility of a collision, an operation that grows exponentially as the resolution is increased. The novel approach presented here reduces the need for these convolutions by using a set of offline precomputed maps that are updated, by means of a partial convolution, as new information arrives from sensors or other sources. Not only does this improve run-time performance, but it also provides support for dynamic search in changing environments. A set of alternative fast convolution methods are also proposed, depending on whether the environment is cluttered with obstacles or not. Finally, we provide both theoretical and experimental results from different experiments and applications.

  3. Bifunctional Asymmetric Catalysis with Hydrogen Chloride: Enantioselective Ring-Opening of Aziridines Catalyzed by a Phosphinothiourea.

    Science.gov (United States)

    Mita, Tsuyoshi; Jacobsen, Eric N

    2009-06-01

    Ring-opening of aziridines with hydrogen chloride to form β-chloroamine derivatives is catalyzed by a chiral phosphinothiourea derivative in high yields and with high enantioselectivities. On the basis of (31)P NMR studies, activation of HCl appears to proceed via quantitative protonation of the catalyst to afford a phosphonium chloride complex.

  4. Comparison of lifetime-based methods for 2D phosphor thermometry in high-temperature environment

    Science.gov (United States)

    Peng, Di; Liu, Yingzheng; Zhao, Xiaofeng; Kim, Kyung Chun

    2016-09-01

    This paper discusses the currently available techniques for 2D phosphor thermometry, and compares the performance of two lifetime-based methods: high-speed imaging and the dual-gate. High-speed imaging resolves luminescent decay with a fast frame rate, and has become a popular method for phosphor thermometry in recent years. But it has disadvantages such as high equipment cost and long data processing time, and it would fail at sufficiently high temperature due to a low signal-to-noise ratio and short lifetime. The dual-gate method only requires two images on the decay curve and therefore greatly reduces cost in hardware and processing time. A dual-gate method for phosphor thermometry has been developed and compared with the high-speed imaging method through both calibration and a jet impingement experiment. Measurement uncertainty has been evaluated for a temperature range of 473-833 K. The effects of several key factors on uncertainty have been discussed, including the luminescent signal level, the decay lifetime and temperature sensitivity. The results show that both methods are valid for 2D temperature sensing within the given range. The high-speed imaging method shows less uncertainty at low temperatures where the signal level and the lifetime are both sufficient, but its performance is degraded at higher temperatures due to a rapidly reduced signal and lifetime. For T  >  750 K, the dual-gate method outperforms the high-speed imaging method thanks to its superiority in signal-to-noise ratio and temperature sensitivity. The dual-gate method has great potential for applications in high-temperature environments where the high-speed imaging method is not applicable.

  5. Microbial reductive dehalogenation of vinyl chloride

    Energy Technology Data Exchange (ETDEWEB)

    Spormann, Alfred M [Stanford, CA; Muller, Jochen A [Baltimore, MD; Rosner, Bettina M [Berlin, DE; Von Abendroth, Gregory [Mannheim, DE; Meshulam-Simon, Galit [Los Angeles, CA; McCarty, Perry L [Stanford, CA

    2014-02-11

    Compositions and methods are provided that relate to the bioremediation of chlorinated ethenes, particularly the bioremediation of vinyl chloride by Dehalococcoides-like organisms. An isolated strain of bacteria, Dehalococcoides sp. strain VS, that metabolizes vinyl chloride is provided; the genetic sequence of the enzyme responsible for vinyl chloride dehalogenation; methods of assessing the capability of endogenous organisms at an environmental site to metabolize vinyl chloride; and a method of using the strains of the invention for bioremediation.

  6. SRAM-Based Passive Dosimeter for High-Energy Accelerator Environments

    CERN Document Server

    Makowski, D R; Napieralski, A; Swiercz, B P

    2005-01-01

    This paper reports a novel NVRAM-based neutron dose monitor (REM counter). The principle of this device is based on the radiation effect initiating the Single Event Upset SEU in high density microelectronic memories. Several batches of Non-Volatile memories from different manufactures were examined in various radiation environments, i.e. 241Am-Be (alpha,n) and Linear accelerators produced radiation fields. A suitable moderator was used to enhance the detector sensitivity. Further experiments were carried out in Linear Accelerators: Linac II, TTF2 and Beam Loss Environment of various Experimental Facilities at DESY Research Centre in Hamburg. A separate batch of SRAM was irradiated with 60Co-gamma rays up to a dose of about 60 Gy. No Single Event Upset (SEU) was registered. This validates, that gamma radiation has a negligible effect to trigger SEU in the SRAM. The proposed detector could be ideal for a neutron dose measurement produced by a high-energy electron linac, including synchrotron and Free Electron L...

  7. Prehistoric Human Dispersal to the Tibetan Plateau and Adaptation to the High Altitude Environment

    Science.gov (United States)

    Zhang, Dongju; Dong, Guanghui; Chen, Fahu

    2016-04-01

    Human history of the Tibetan Plateau and human adaptation to the high altitude environment is hotly debated in the past decade among archaeological, anthropological, genetic, and even past climate change studies. Based on previous studies on the Tibetan Plateau and our own archaeological studies in northeastern Tibetan Plateau (NETP), we propose that human migrated to the Tibetan Plateau from the last Deglacial period to late Holocene mainly from North China via Yellow River valley and its tributary valleys in NETP. This migration is constituted of four stages (Upper Paleolithic, Epi-Paleolithic, Neolithic and Bronze Age) when human adapted to the high altitude environment and climate change with different strategies and techniques. Particularly, the prevail of microlithic technology in North China provoked hunter-gatherers' first visit to the NETP in relatively ameliorated last Deglacial period, and the quick development of millet farming and subsequent mixed barley-wheat farming and sheep herding facilitated farmers and herders permanently settled in NETP, even above 3000 masl, during mid- and late Holocene.

  8. An empirical model of the high-energy electron environment at Jupiter

    Science.gov (United States)

    Soria-Santacruz, M.; Garrett, H. B.; Evans, R. W.; Jun, I.; Kim, W.; Paranicas, C.; Drozdov, A.

    2016-10-01

    We present an empirical model of the energetic electron environment in Jupiter's magnetosphere that we have named the Galileo Interim Radiation Electron Model version-2 (GIRE2) since it is based on Galileo data from the Energetic Particle Detector (EPD). Inside 8RJ, GIRE2 adopts the previously existing model of Divine and Garrett because this region was well sampled by the Pioneer and Voyager spacecraft but poorly covered by Galileo. Outside of 8RJ, the model is based on 10 min averages of Galileo EPD data as well as on measurements from the Geiger Tube Telescope on board the Pioneer spacecraft. In the inner magnetosphere the field configuration is dipolar, while in the outer magnetosphere it presents a disk-like structure. The gradual transition between these two behaviors is centered at about 17RJ. GIRE2 distinguishes between the two different regions characterized by these two magnetic field topologies. Specifically, GIRE2 consists of an inner trapped omnidirectional model between 8 to 17RJ that smoothly joins onto the original Divine and Garrett model inside 8RJ and onto a GIRE2 plasma sheet model at large radial distances. The model provides a complete picture of the high-energy electron environment in the Jovian magnetosphere from ˜1 to 50RJ. The present manuscript describes in great detail the data sets, formulation, and fittings used in the model and provides a discussion of the predicted high-energy electron fluxes as a function of energy and radial distance from the planet.

  9. Cassava root scrapings for 22 to 42-day-old broilers in high-temperature environments

    Directory of Open Access Journals (Sweden)

    Antônio Hosmylton Carvalho Ferreira

    2012-06-01

    Full Text Available The objective of this study was to analyze the effect of whole cassava root scrapings at different levels in diets for broilers in the period of 22 to 42 days of age in high-temperature environments on performance, as well as to evaluate the metabolizability of dry matter (DM, crude protein (CP and gross energy (GE and nitrogen balance. A total of 400 male Ross broilers were used for evaluation of performance and 80 birds of the same strain were used in the metabolism experiment. The design was of randomized block with five treatments and four replications. The experimental unit was represented by twenty birds on the performance evaluation and four birds were housed in metabolic cages for the metabolism evaluation. The treatments consisted of diets containing inclusion levels of cassava root scrapings (0, 50, 100, 150 and 200 g/kg, formulated to meet the nutritional requirements accordingly to each phase of the birds. Whole cassava root scrapings can be included in diets for 22 to 42 day-old broiler chickens, at a level between 118.75 and 200 k/kg, in environments of high temperatures, with positive interference on weight gain and feed conversion, without affecting the coefficient of metabolizability of dry matter, crude protein, gross energy and nitrogen balance, or carcass characteristics, such as yields of main cuts and metabolically active organs of the birds.

  10. A high UV environment does not ensure adequate Vitamin D status

    Science.gov (United States)

    Kimlin, M. G.; Lang, C. A.; Brodie, A.; Harrison, S.; Nowak, M.; Moore, M. R.

    2006-12-01

    Queensland has the highest rates of skin cancer in the world and due to the high levels of solar UV in this region it is assumed that incidental UV exposure should provide adequate vitamin D status for the population. This research was undertaken to test this assumption among healthy free-living adults in south-east Queensland, Australia (27°S), at the end of winter. This research was approved by Queensland University of Technology Human Research Ethics Committee and conducted under the guidelines of the Declaration of Helsinki. 10.2% of the sample had serum vitamin D levels below 25nm/L (deficiency) and a further 32.3% had levels between 25nm/L and 50nm/L (insufficiency). Vitamin D deficiency and insufficiency can occur at the end of winter, even in sunny climates. The wintertime UV levels in south-east Queensland (UV index 4-6) are equivalent to summertime UV levels in northern regions of Europe and the USA. These ambient UV levels are sufficient to ensure synthesis of vitamin D requirements. We investigated individual UV exposure (through a self reported sun exposure questionnaire) and found correlations between exposure and Vitamin D status. Further research is needed to explore the interactions between the solar UV environment and vitamin D status, particularly in high UV environments, such as Queensland.

  11. HIGH-RESOLUTION MONITORING OF CURRENT RAPID TRANSFORMATIONS ON GLACIAL AND PERIGLACIAL ENVIRONMENTS

    Directory of Open Access Journals (Sweden)

    L. Carturan

    2014-01-01

    Full Text Available Glacial and periglacial environments are highly sensitive to climatic changes. Processes of cryosphere degradation may strongly impact human activities and infrastructures, and need to be monitored for improved understanding and for mitigation/adaptation. Studying glacial and periglacial environments using traditional techniques may be difficult or not feasible, but new remote sensing techniques like terrestrial and aerial laser scanner opened new possibilities for cryospheric studies. This work presents an application of the terrestrial laser scanner (TLS for monitoring the current rapid changes occurring on the Montasio Occidentale glacier (Eastern Italian alps, which is representative of low-altitude, avalanche-fed and debris-cover glaciers. These glaciers are quite common in the Alps but their reaction to climate changes is still poorly known. The mass balance, surface velocity fields, debris cover dynamics and effects of meteorological extremes were investigated by repeat high-resolution TLS scanning from September 2010 to October 2012. The results were encouraging and shed light on the peculiar response of this glacier to climatic changes, on its current dynamics and on the feedback played by the debris cover, which is critical for its preservation. The rapid transformations in act, combined with the unstable ice mass, large amount of loose debris and channeled runoff during intense rainfalls, constitute a potential area for the formation of large debris flows, as shown by field evidences and documented by the recent literature.

  12. Corrosion Testing of Ni Alloy HVOF Coatings in High Temperature Environments for Biomass Applications

    Science.gov (United States)

    Paul, S.; Harvey, M. D. F.

    2013-03-01

    This paper reports the corrosion behavior of Ni alloy coatings deposited by high velocity oxyfuel spraying, and representative boiler substrate alloys in simulated high temperature biomass combustion conditions. Four commercially available oxidation resistant Ni alloy coating materials were selected: NiCrBSiFe, alloy 718, alloy 625, and alloy C-276. These were sprayed onto P91 substrates using a JP5000 spray system. The corrosion performance of the coatings varied when tested at ~525, 625, and 725 °C in K2SO4-KCl mixture and gaseous HCl-H2O-O2 containing environments. Alloy 625, NiCrBSiFe, and alloy 718 coatings performed better than alloy C-276 coating at 725 °C, which had very little corrosion resistance resulting in degradation similar to uncoated P91. Alloy 625 coatings provided good protection from corrosion at 725 °C, with the performance being comparable to wrought alloy 625, with significantly less attack of the substrate than uncoated P91. Alloy 625 performs best of these coating materials, with an overall ranking at 725 °C as follows: alloy 625 > NiCrBSiFe > alloy 718 ≫ alloy C-276. Although alloy C-276 coatings performed poorly in the corrosion test environment at 725 °C, at lower temperatures (i.e., below the eutectic temperature of the salt mixture) it outperformed the other coating types studied.

  13. [Analysis of Electric Stress in Human Head in High-frequency Low-power Electromagnetic Environment].

    Science.gov (United States)

    Zhou, Yongjun; Zhang, Hui; Niu, Zhongqi

    2015-04-01

    Action of electromagnetic radiation exerting on human body has been a concerned issue for people. Because electromagnetic waves could generate an electric stress in a discontinuous medium, we used the finite difference time domain (FDTD) as calculation methods to calculate the electric stress and its distribution in human head caused by high-frequency low-power electromagnetic environment, which was generated by dual-band (900 MHz and 1 800 MHz) PIFA antennas with radiated power 1 W, and we then performed the safety evaluation of cell phone radiation from the angle whether the electric stress further reached the human hearing threshold. The result showed that there existed the electric stress at the interface of different permittivity organization caused by the two kinds of high-frequency low-power electromagnetic environment and the maximum electric stress was located at the interface between skin and air of the phone side, and the electric stress peak at skull did not reach the threshold of auditory caused by bone tissue conduction so that it can not produce auditory effects.

  14. Deployment of a highly secure clinical data repository in an insecure international environment.

    Science.gov (United States)

    Feldman, Henry; Reti, Shane; Kaldany, Eli; Safran, Charles

    2010-01-01

    We have designed and deployed a novel approach to protecting Personal Healthcare Information in environments where a data center is remote and its physical security cannot be assured. Our "KeyServer" methodology uses a server-client-server architecture to dynamically serve keys from a distant server in a separate secure data center in the US. The approach combines pre-existing and novel techniques into a layered protective barrier around compromise of patient data. We describe how this technology provides scalable security that makes security breaches highly unlikely. With some careful planning a Clinical Data Repositories fed by Electronic Health Records can be placed in relatively insecure settings, with a high-level of security surrounding data theft, even in the event of hardware theft. Such security architecture is ideal for not only developing nations, but for the evolution of health information to cloud computing platforms.

  15. High resolution rainfall – runoff measurement setup for green roof experiments in a tropical environment

    Directory of Open Access Journals (Sweden)

    T. Vergroesen

    2010-12-01

    Full Text Available This article describes the measurement setup that is used for green roof experiments in a tropical environment, the required data treatment to obtain reliable values of rainfall, runoff and evapotranspiration, and how to deal with external disturbances that can influence the experiment results. High resolution rainfall runoff measurements to identify, understand and properly model the relevant runoff processes in a green roof require both tailored equipment and data treatment. A tipping bucket rain gauge is calibrated for and installed to measure minute based rain intensities. A runoff measuring setup is developed that can accurately quantify the runoff up to 6 l/min, and has a high resolution in both time and volume. Two different measuring setups are used to verify the evapotranspiration that is derived from the rainfall and runoff measurements.

  16. High-dimensional quantum state transfer in a noisy network environment

    Institute of Scientific and Technical Information of China (English)

    秦伟; 李俊林; 龙桂鲁

    2015-01-01

    We propose and analyze an efficient high-dimensional quantum state transfer protocol in an XX coupling spin network with a hypercube structure or chain structure. Under free spin wave approximation, unitary evolution results in a perfect high-dimensional quantum swap operation requiring neither external manipulation nor weak coupling. Evolution time is independent of either distance between registers or dimensions of sent states, which can improve the computational efficiency. In the low temperature regime and thermodynamic limit, the decoherence caused by a noisy environment is studied with a model of an antiferromagnetic spin bath coupled to quantum channels via an Ising-type interaction. It is found that while the decoherence reduces the fidelity of state transfer, increasing intra-channel coupling can strongly suppress such an effect. These observations demonstrate the robustness of the proposed scheme.

  17. Efficient visualization techniques for high resolution remotely sensed data in a network environment

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    There are three major research hotspots in efficient visualization techniques of high resolution remotely sensed data in network environment: the data organiza-tion and access in disk storage,the image data stitching and fitting methods,and the network transfers and access. In this paper a new method of "Big File" organi-zation for improving the storage access efficiency of high resolution remote data is presented; a "virtual data source" concept is introduced to solve the stitching problem of remotely sensed data from different sources with different resolutions; a remotely sensed data access engine design based on ATL technique is discussed to process the network transfers and access of remotely sensed data. All these techniques have been adopted in a prototype of digital China named "ChinaStar".

  18. Genetically encoded optical sensors for monitoring of intracellular chloride and chloride-selective channel activity

    Directory of Open Access Journals (Sweden)

    Piotr Bregestovski

    2009-12-01

    Full Text Available This review briefly discusses the main approaches for monitoring chloride (Cl−, the most abundant physiological anion. Noninvasive monitoring of intracellular Cl− ([Cl−]i is a challenging task owing to two main difficulties: (i the low transmembrane ratio for Cl−, approximately 10:1; and (ii the small driving force for Cl−, as the Cl− reversal potential (ECl is usually close to the resting potential of the cells. Thus, for reliable monitoring of intracellular Cl−, one has to use highly sensitive probes. From several methods for intracellular Cl− analysis, genetically encoded chloride indicators represent the most promising tools. Recent achievements in the development of genetically encoded chloride probes are based on the fact that yellow fluorescent protein (YFP exhibits Cl−-sensitivity. YFP-based probes have been successfully used for quantitative analysis of Cl− transport in different cells and for high-throughput screening of modulators of Cl−-selective channels. Development of a ratiometric genetically encoded probe, Clomeleon, has provided a tool for noninvasive estimation of intracellular Cl− concentrations. While the sensitivity of this protein to Cl− is low (EC50 about 160 mM, it has been successfully used for monitoring intracellular Cl− in different cell types. Recently a CFP–YFP-based probe with a relatively high sensitivity to Cl− (EC50 about 30 mM has been developed. This construct, termed Cl-Sensor, allows ratiometric monitoring using the fluorescence excitation ratio. Of particular interest are genetically encoded probes for monitoring of ion channel distribution and activity. A new molecular probe has been constructed by introducing into the cytoplasmic domain of the Cl−-selective glycine receptor (GlyR channel the CFP–YFP-based Cl-Sensor. This construct, termed BioSensor-GlyR, has been successfully expressed in cell lines. The new genetically encoded chloride probes offer means of screening

  19. Silicon carbide resonant tuning fork for microsensing applications in high-temperature and high G-shock environments

    Institute of Scientific and Technical Information of China (English)

    David R Myers; Kan Bun Cheng; Babak Jamshidi; Robert G Azevedo; Debbie G Senesky; Li Chen; Mehran Mehregany; Muthu B J Wijesundara; Albert P Pisano

    2012-01-01

    We present the fabrication and testing of a silicon carbide (SiC) balanced mass doublended tuning fork that survives harsh environments without compromising the device strain sensitivity and resolution bandwidth. The device features a material stack that survives corrosive environments and enables high-temperature operation. To perform hightemperature testing, a specialized setup was constructed that allows the tuning fork to be characterized using traditional silicon electronics. The tuning fork has been operated at 600°C in the presence of dry steam for short durations. This tuning fork has also been tested to 64 000 G using a hard-launch, soft-catch shock implemented with a light gas gun. However, the device still has a strain sensitivity of 66 Hz/μe and strain resolution of 0. 045 μe in a 10 kHz bandwidth. As such, this balanced-mass double-ended tuning fork can be used to create a variety of different sensors including strain gauges, accelerometers, gyroscopes, and pressure transducers. Given the adaptable fabrication process flow, this device could be useful to micro-electro-mechanical systems (MEMS) designers creating sensors for a variety of different applications.

  20. 高效液相色谱法同时测定化妆品中的3种苯扎氯铵同系物%Simultaneous determination of 3 benzalkonium chloride homologsin cosmetics by high performance liquid chromatography

    Institute of Scientific and Technical Information of China (English)

    刘艳琴; 王浩; 杨红梅; 史海良; 郭启雷

    2011-01-01

    建立了采用高效液相色谱-二极管阵列检测器(HPLC-DAD)同时检测化妆品中3种苯扎氯铵同系物(n-CH-CHNCl、n-CH-CHNCl、n-CH-CHNCl)的方法.采用含0.5%甲酸的甲醇超声提取样品,以CAPCELL PAK SCX色谱柱(250 mm×4.6 mm,5 μm)分离,流动相为40 mmol/L乙酸铵水溶液(含0.1%三乙胺,pH 4.0)和乙腈,梯度洗脱,流速1.0 mL/min,检测波长260 nm,柱温25℃,进样量20 μL.该方法的检出限50.0 mg/kg,定量限200.0 mg/kg,线性范围5.0~3 000.0 mg/L,加标回收率92.5%~102.1%.相对标准偏差为3.81%~6.66%.结果表明,该方法快速、准确,能够同时测定化妆品中3种苯扎氯铵同系物.%An analytical method based on high performance liquid chromatography with a diode array detector (HPLC-DAD) has been established for the simultaneous determination of 3 benzalkonium chloride homologs (n-C12H25-C9H13NCl, n-C14H29-C9H13NCI, n-C16H33-C9H13NCl) in cosmetics.The sample was extracted with methanol ( including 0.5% formic acid) under ultrasonic operation, the HPLC separation was carried out on a CAPCELL PAK SCX column (250 mm × 4.6 mm, 5 μm), the mobile phases were 40 mmol/L ammonium acetate solution (including 0.1% triethylamine) and acetonitrile with gradient elution, the flow rate was 1.0 mL/min, the detection wavelength was 260 nm, the column temperature was 25 ℃, and the injection volume was 20 μL.The limit of detection was 50.0 mg/kg and the quantitation limit was 200.0 mg/kg for 3 benzalkonium chloride homologs in cosmetics.The linear plots were obtained between 5.0 mg/L and 3 000.0 mg/L.Overall recoveries were between 92.5% and 102.1% with the relative standard deviations (RSDs) between 3.81% and 6.66%.The method is simple, rapid, accurate and suitable for the determination of 3 benzalkonium chloride homologs in cosmetics.

  1. Cystic Fibrosis (CF): Chloride Sweat Test

    Science.gov (United States)

    ... Old Feeding Your 1- to 2-Year-Old Cystic Fibrosis (CF) Chloride Sweat Test KidsHealth > For Parents > Cystic Fibrosis (CF) Chloride Sweat Test Print A A A ... It Is A chloride sweat test helps diagnose cystic fibrosis (CF) , an inherited disorder that makes kids sick ...

  2. 21 CFR 184.1426 - Magnesium chloride.

    Science.gov (United States)

    2010-04-01

    ... mineral bischofite. It is prepared by dissolving magnesium oxide, hydroxide, or carbonate in aqueous... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Magnesium chloride. 184.1426 Section 184.1426 Food... Specific Substances Affirmed as GRAS § 184.1426 Magnesium chloride. (a) Magnesium chloride (MgC12·6H2O,...

  3. 75 FR 33824 - Barium Chloride From China

    Science.gov (United States)

    2010-06-15

    ... COMMISSION Barium Chloride From China Determination On the basis of the record\\1\\ developed in the subject... order on barium chloride from China would be likely to lead to continuation or recurrence of material... Barium Chloride from China: Investigation No. 731-TA-149 (Third Review). By order of the...

  4. 75 FR 19657 - Barium Chloride From China

    Science.gov (United States)

    2010-04-15

    ... COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Notice of... chloride from China. SUMMARY: The Commission hereby gives notice that it will proceed with a full review... revocation of the antidumping duty order on barium chloride from China would be likely to lead...

  5. 21 CFR 172.180 - Stannous chloride.

    Science.gov (United States)

    2010-04-01

    ... Preservatives § 172.180 Stannous chloride. The food additive stannous chloride may be safely used for color... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Stannous chloride. 172.180 Section 172.180 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR...

  6. 21 CFR 582.5446 - Manganese chloride.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Manganese chloride. 582.5446 Section 582.5446 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) ANIMAL... Supplements 1 § 582.5446 Manganese chloride. (a) Product. Manganese chloride. (b) Conditions of use....

  7. Application of cyanuric chloride-based six new chiral derivatizing reagents having amino acids and amino acid amides as chiral auxiliaries for enantioresolution of proteinogenic amino acids by reversed-phase high-performance liquid chromatography.

    Science.gov (United States)

    Bhushan, Ravi; Dixit, Shuchi

    2012-04-01

    Six dichloro-s-triazine (DCT) reagents having L-Leu, D-Phg, L-Val, L-Met, L-Ala and L-Met-NH(2) as chiral auxiliaries in cyanuric chloride were introduced for enantioseparation of 13 proteinogenic amino acids. Four other DCTs and six monochloro-s-triazine (MCT) reagents having amino acid amides as chiral auxiliaries were also synthesized. These 16 chiral derivatizing reagents (CDRs) were used for synthesis of diastereomers of all the 13 analytes using microwave irradiation, which were resolved by reversed-phase high-performance liquid chromatography (RP-HPLC) using C18 column and gradient eluting mixture of aqueous TFA and acetonitrile with UV detection at 230 nm. It required only 60-90 s for derivatization using microwave irradiation. Better resolution and lower retention times were observed for the diastereomers prepared with CDRs having amino acids as chiral auxiliaries as compared to counterparts prepared with reagents having amino acid amides as chiral auxiliaries. As the best resolution of all the 13 analytes was observed for their diastereomers prepared using the DCT reagent having L-Leu as chiral auxiliary, this CDR was further employed for derivatization of Lys, Tyr, His and Arg followed by RP-HPLC analysis of resulting diastereomers. The results are discussed in light of acid and amide groups of chiral auxiliaries constituting CDRs, electronegativities of the atoms of achiral moieties constituting CDRs and hydrophobicities of side chains of amino acids constituting CDRs and analytes.

  8. Investigation of the reactions of chlorides binding to aluminates using XRD and DTA methods

    Directory of Open Access Journals (Sweden)

    Bikić Farzet H.

    2009-01-01

    Full Text Available The reactions of chlorides binding to aluminates were investigated by analyzing the monochloroaluminate hydrate, product of the reaction. The results show that the product is formed in the fresh concrete, after adding chloride within the stage of the preparation of concrete, as well as adding chlorides by penetration from the environment into the concrete. The obtained results are significant, considering the aspect of preventing corrosion of the steel reinforcement into the concrete. It is known that only free chlorides activate corrosion processes in the steel reinforcement in concrete. The process of chloride bonding is followed by X-ray diffraction (XRD and differential thermal (DTA analysis of samples of the cement paste, which is the process of preparation and care is described in detail in this work.

  9. A novel capsule-based self-recovery system with a chloride ion trigger

    Science.gov (United States)

    Xiong, Wei; Tang, Jiaoning; Zhu, Guangming; Han, Ningxu; Schlangen, Erik; Dong, Biqin; Wang, Xianfeng; Xing, Feng

    2015-06-01

    Steel is prone to corrosion induced by chloride ions, which is a serious threat to reinforced concrete structures, especially in marine environments. In this work, we report a novel capsule-based self-recovery system that utilizes chloride ions as a trigger. These capsules, which are functionalized via a smart response to chloride ions, are fabricated using a silver alginate hydrogel that disintegrates upon contact with chloride ions, and thereby releases the activated core materials. The experimental results show that the smart capsules respond to a very low concentration of chloride ions (0.1 wt%). Therefore, we believe that this novel capsule-based self-recovery system will exhibit a promising prospect for self-healing or corrosion inhibition applications.

  10. High affinity and temperature sensitivity of blood oxygen binding in Pangasianodon hypophthalmus due to lack of chloride-hemoglobin allosteric interaction

    DEFF Research Database (Denmark)

    Damsgaard, Christian; Phuong, Le My; Huong, Do Thi Thanh

    2015-01-01

    Air-breathing fishes represent interesting organisms in terms of understanding the physiological changes associated with the terrestrialization of vertebrates, and, further, are of great socio-economic importance for aquaculture in Southeast Asia. To understand how environmental factors, such as ......Air-breathing fishes represent interesting organisms in terms of understanding the physiological changes associated with the terrestrialization of vertebrates, and, further, are of great socio-economic importance for aquaculture in Southeast Asia. To understand how environmental factors...... saturation P50 = 4.6 mmHg at extracellular pH 7.6 and 25°C), a high temperature sensitivity of O2 binding (apparent heat of oxygenation ΔHapp = -28.3 kcal/mol), and lacked a Root effect. Further, the data on Hb revealed weak ATP binding and a complete lack of Cl- binding to Hb, which, in part, explains...

  11. Study the Effectiveness of Technology-Enhanced Interactive Teaching Environment on Student Learning of Junior High School Biology

    Science.gov (United States)

    Yang, Kai-Ti; Wang, Tzu-Hua; Chiu, Mei-Hung

    2015-01-01

    This research investigates the effectiveness of integrating Interactive Whiteboard (IWB) into the junior high school biology teaching. This research adopts a quasi-experimental design and divides the participating students into the conventional ICT-integrated learning environment and IWB-integrated learning environment. Before teaching, students…

  12. Characterization of high-yield performance as affected by genotype and environment in rice

    Institute of Scientific and Technical Information of China (English)

    Song CHEN; Fang-rong ZENG; Zong-zhi PAO; Guo-ping ZHANG

    2008-01-01

    We characterized yield-relevant characters and their variations over genotypes and environments (locations and years) by examining two rice varieties (9746 and Jinfeng) with high yield potential.9746 and Jinfeng were planted in two locations of Shanghai,China,during 2005 and 2006.The results show that there was a large variation in grain yield between locations and years.The realization of high yield potential for the two types of rice was closely related to the improved sink size,such as more panicles per square meter or grains per panicle.Stem and leaf biomasses were mainly accumulated from tillering stage to heading stage,and showed slow decline during grain filling.Meanwhile,some photosynthetic characters including net photosynthesis rate (Pn),leaf area index (LAI),specific leaf area (SLA),fluorescence parameter (maximum quantum yield of PSII,Fv/Fm),chlorophyll content (expressed as SPAD value),as well as nutrient (N,P,K) uptake were also measured to determine their variations over genotypes and environments and their relationships with grain yield.Although there were significant differences between years or locations for most measurements,SLA at tillering and heading stages,Fv/Fm and LAI at heading stage,stem biomass at heading and maturity stages,and leaf nitrogen concentration at tillering and heading stages remained little changed,indicating their pos-sible applications as selectable characters in breeding programs.It was also found that stem nitrogen accumulation at tillering stage is one of the most important and stable traits for high yield formation.

  13. High Resolution Spatial Analysis of Habitat Preference of Aedes Albopictus (Diptera: Culicidae) in an Urban Environment.

    Science.gov (United States)

    Cianci, Daniela; Hartemink, Nienke; Zeimes, Caroline B; Vanwambeke, Sophie O; Ienco, Annamaria; Caputo, Beniamino

    2015-05-01

    Over the past decades, the Asian tiger mosquito (Aedes albopictus (Skuse, 1895)) has emerged in many countries, and it has colonized new environments, including urban areas. The species is a nuisance and a potential vector of several human pathogens, and a better understanding of the habitat preferences of the species is needed for help in successful prevention and control. So far, the habitat preference in urban environments has not been studied in Southern European cities. In this paper, spatial statistical models were used to evaluate the relationship between egg abundances and land cover types on the campus of Sapienza University in Rome, which is taken as an example of a European urban habitat. Predictor variables included land cover types, classified in detail on a high resolution image, as well as solar radiation and month of capture. The models account for repeated measures in the same trap and are adjusted for meteorological circumstances. Vegetation and solar radiation were found to be positively related to the number of eggs. More specifically, trees were positively related to the number of eggs and the relationship with grass was negative. These findings are consistent with the species' known preference for shaded areas. The unexpected positive relationship with solar radiation is amply discussed in the paper. This study represents a first step toward a better understanding of the spatial distribution of Ae. albopictus in urban environments. © The Authors 2015. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  14. Monitoring performance of the cameras under the high dose-rate gamma ray environments.

    Science.gov (United States)

    Cho, Jai Wan; Choi, Young Soo; Jeong, Kyung Min

    2014-05-01

    CCD/CMOS cameras, loaded on a robot system, are generally used as the eye of the robot and monitoring unit. A major problem that arises when dealing with images provided by CCD/CMOS cameras under severe accident situations of a nuclear power plant is the presence of speckles owing to the high dose-rate gamma irradiation fields. To use a CCD/CMOS camera as a monitoring unit in a high radiation area, the legibility of the camera image in such intense gamma-radiation fields should therefore be defined. In this paper, the authors describe the monitoring index as a figure of merit of the camera's legibleness under a high dose-rate gamma ray irradiation environment. From a low dose-rate (10 Gy h) to a high dose-rate (200 Gy h) level, the legible performances of the cameras owing to the speckles are evaluated. The numbers of speckles generated by gamma ray irradiation in the camera image are calculated by an image processing technique. The legibility of the sensor indicator (thermo/hygrometer) owing to the number of speckles is also presented.

  15. High temperature measurements in irradiated environment using Raman fiber optics distributed temperature sensing

    Science.gov (United States)

    Lecomte, Pierre; Blairon, Sylvain; Boldo, Didier; Taillade, Frédéric; Caussanel, Matthieu; Beauvois, Gwendal; Duval, Hervé; Grieu, Stéphane; Laffont, Guillaume; Lainé, Frédéric; Carrel, Frédéric

    2016-04-01

    Optical fiber temperature sensors using Raman effect are a promising technology for temperature mapping of nuclear power plant pipes. These pipes are exposed to high temperature (350 °C) and gamma radiations, which is a harsh environment for standard telecom fibers. Therefore metal coated fibers are to be used to perform measurement over 300 °C. Temperature variations can affect the attenuation of the metallic coated fiber before irradiation. The latter induces an extra attenuation, due to light absorption along the fiber by radiation-induced defects. The recombination of these defects can be strongly accelerated by the high temperature value. As backscattered Raman signal is weak it is important to test optical fibers under irradiation to observe how it gets attenuated. Different experiments are described in this conference paper: two in situ irradiation campaigns with different dose rates at, both ambient and high temperature. We observe that the tested off-the-shelf metallic coated fibers have a high attenuation under irradiation. We also noticed the fact that thermal annealing plays a massive role in the +300 °C temperature range.

  16. Muramic Acid Measurements for Bacterial Investigations in Marine Environments by High-Pressure Liquid Chromatography

    Science.gov (United States)

    Mimura, Toru; Romano, Jean-Claude

    1985-01-01

    Muramic acid, a constituent of procaryotic cell walls, was assayed by high-pressure liquid chromatography in samples from several marine environments (water column, surface microlayer, and sediment) and a bacterial culture. It is used as a microbial biomass indicator. The method gave a good separation of muramic acid from interfering compounds with satisfactory reproducibility. A pseudomonad culture had a muramic acid content of 4.7 × 10−10 to 5.3 × 10−10 μg per cell during growth. In natural water samples, highly significant relationships were found between muramic acid concentrations and bacterial numbers for populations of 108 to 1011 cells per liter. The muramic acid content in natural marine water decreased from 5.3 × 10−10 to 1.6 × 10−10 μg per cell with increasing depth. In coastal sediments exposed to sewage pollution, concentrations of muramic acid, ATP, organic carbon, and total amino acids displayed a parallel decrease with increasing distance from the sewage outlet. Advantages of muramic acid measurement by high-pressure liquid chromatography are its high sensitivity and reduction of preparation steps, allowing a short time analysis. PMID:16346848

  17. High Osmolarity Environments Activate the Mitochondrial Alternative Oxidase in Debaryomyces Hansenii

    Science.gov (United States)

    Garcia-Neto, Wilson; Cabrera-Orefice, Alfredo; Uribe-Carvajal, Salvador; Kowaltowski, Alicia J.; Alberto Luévano-Martínez, Luis

    2017-01-01

    The oleaginous yeast Debaryomyces hansenii is a good model to understand molecular mechanisms involved in halotolerance because of its impressive ability to survive under a wide range of salt concentrations. Several cellular adaptations are implicated in this response, including the presence of a cyanide-insensitive ubiquinol oxidase (Aox). This protein, which is present in several taxonomical orders, has been related to different stress responses. However, little is known about its role in mitochondria during transitions from low to high saline environments. In this report, we analyze the effects of Aox in shifts from low to high salt concentrations in the culture media. At early stages of a salt insult, we observed that this protein prevents the overflow of electrons on the mitochondrial respiratory chain, thus, decreasing the production of reactive oxygen species. Interestingly, in the presence of high osmolite concentrations, Aox activity is able to sustain a stable membrane potential when coupled to complex I, despite a compromised cytochrome pathway. Taken together, our results suggest that under high osmolarity conditions Aox plays a critical role regulating mitochondrial physiology. PMID:28060946

  18. Replacing Chlorine with Hydrogen Chloride as a Possible Reactant for Synthesis of Titanium Carbide Derived Carbon Powders for High-Technology Devices

    Science.gov (United States)

    Tallo, Indrek; Thomberg, Thomas; Jänes, Alar; Lust, Enn

    2013-12-01

    Micro- and mesoporous carbide-derived carbons were synthesized from titanium carbide (TiC) powder via gas phase reaction by using different reactants (Cl2 and HCl) within the temperature range from 700 to 1100 °C. Analysis of XRD results show that TiC-derived carbons (TiC-CDC) consist mainly of graphitic crystallites. The first-order Raman spectra showed the graphite-like absorption peaks at ~1577 cm1 and the disorder-induced peaks at ~1338 cm-1. The energy-related properties of supercapacitors based on 1 M (C2H5)3CH3NBF4 in acetonitrile and carbide-derived carbons (TiC-CDC (Cl2) and TiC-CDC (HCl)) as electrode materials were also investigated using cyclic voltammetry, electrochemical impedance spectroscopy, galvanostatic charge/discharge and constant power methods. The Ragone plots for carbide-derived carbons prepared by using different reactants (Cl2, HCl) are quite similar and at high power loads TiC-CDC (Cl2) material synthesized at 900 °C, i.e. materials with optimal porous structure, deliver higher power at constant energy.

  19. Water use strategies and ecosystem-atmosphere exchange of CO2 in two highly seasonal environments

    Science.gov (United States)

    Arneth, A.; Veenendaal, E. M.; Best, C.; Timmermans, W.; Kolle, O.; Montagnani, L.; Shibistova, O.

    2006-09-01

    We compare assimilation and respiration rates, and water use strategies in four divergent ecosystems located in cold-continental central Siberia and in semi-arid southern Africa. These seemingly unrelated systems have in common a harsh and highly seasonal environment with a very sharp transition between the dormant and the active season, with vegetation facing dry air and soil conditions for at least part of the year. Moreover, the northern high latitudes and the semi-arid tropics will likely experience changes in key environmental parameters (e.g., air temperature and precipitation) in the future; indeed, in some regions marked climate trends have already been observed over the last decade or so. The magnitude of instantaneous or daily assimilation and respiration rates, derived from one to two years of eddy covariance measurements in each of the four ecosystems, was not related to the growth environment. For instance, respiration rates were clearly highest in the two deciduous systems included in the analysis (a Mopane woodland in northern Botswana and a Downy birch forest in Siberia; >300 mmol m-2 d-1), while assimilation rates in the Mopane woodland were relatively similar to a Siberian Scots pine canopy for a large part of the active season (ca. 420 mmol m-2 d-1). Acknowledging the limited number of ecosystems compared here, these data nevertheless demonstrate that factors like vegetation type, canopy phenology or ecosystem age can override larger-scale climate differences in terms of their effects on carbon assimilation and respiration rates. By far the highest rates of assimilation were observed in Downy birch, an early successional species. These were achieved at a rather conservative water use, as indicated by relatively low levels of λ, the marginal water cost of plant carbon gain. Surprisingly, the Mopane woodland growing in the semi-arid environment had significantly higher values of λ. However, its water use strategy included a very plastic response

  20. Water use strategies and ecosystem-atmosphere exchange of CO2 in two highly seasonal environments

    Directory of Open Access Journals (Sweden)

    O. Kolle

    2006-04-01

    Full Text Available We compare assimilation and respiration rates, and water use strategies in four divergent ecosystems located in cold-continental central Siberia and in semi-arid southern Africa. These seemingly unrelated systems have in common a harsh and highly seasonal environment with a very sharp transition between the dormant and the active season, and with vegetation facing dry air and soil conditions for at least part of the year. Moreover, the northern high latitudes and the semi-arid tropics will likely experience changes in key environmental parameters (e.g., air temperature and precipitation in the future; indeed, in some regions marked climate trends have already been observed over the last decade or so. The magnitude of instantaneous or daily assimilation and respiration rates, derived from one to two years of eddy covariance measurements in each of the four ecosystems, was not related to the growth environment. For instance, respiration rates were clearly highest in the two deciduous systems included in the analysis (a Mopane woodland in northern Botswana and a Downy birch forest in Siberia; >300 mmol m−2 d−1, while assimilation rates in the Mopane woodland were relatively similar to a Siberian Scots pine canopy for a large part of the active season (ca. 420 mmol m−2 d−1. Acknowledging the limited number of ecosystems compared here, these data nevertheless suggest that factors like vegetation type, canopy phenology or ecosystem age can override larger-scale climate differences in terms of their effects on carbon assimilation and respiration rates. By far the highest rates of assimilation were observed in Downy birch, an early successional species. These were achieved at a rather conservative water use, as indicated by relatively low levels of λ, the marginal water cost of plant carbon gain. Surprisingly, the Mopane woodland growing in the semi-arid environment had significantly higher values of λ. However, its water use strategy