WorldWideScience

Sample records for high bit rates

  1. Circuit and interconnect design for high bit-rate applications

    NARCIS (Netherlands)

    Veenstra, H.

    2006-01-01

    This thesis presents circuit and interconnect design techniques and design flows that address the most difficult and ill-defined aspects of the design of ICs for high bit-rate applications. Bottlenecks in interconnect design, circuit design and on-chip signal distribution for high bit-rate applicati

  2. Design of high-bit-rate coherent communication links

    Science.gov (United States)

    Konyshev, V. A.; Leonov, A. V.; Nanii, O. E.; Novikov, A. G.; Treshchikov, V. N.; Ubaydullaev, R. R.

    2016-12-01

    We report an analysis of the problems encountered in the design of modern high-bit-rate coherent communication links. A phenomenological communication link model is described, which is suitable for solving applied tasks of the network design with nonlinear effects taken into account. We propose an engineering approach to the design that is based on the use of fundamental nonlinearity coefficients calculated in advance for the experimental configurations of communication links. An experimental method is presented for calculating the nonlinearity coefficient of communication links. It is shown that the proposed approach allows one to successfully meet the challenges in designing communication networks.

  3. High bit rate germanium single photon detectors for 1310nm

    Science.gov (United States)

    Seamons, J. A.; Carroll, M. S.

    2008-04-01

    There is increasing interest in development of high speed, low noise and readily fieldable near infrared (NIR) single photon detectors. InGaAs/InP Avalanche photodiodes (APD) operated in Geiger mode (GM) are a leading choice for NIR due to their preeminence in optical networking. After-pulsing is, however, a primary challenge to operating InGaAs/InP single photon detectors at high frequencies1. After-pulsing is the effect of charge being released from traps that trigger false ("dark") counts. To overcome this problem, hold-off times between detection windows are used to allow the traps to discharge to suppress after-pulsing. The hold-off time represents, however, an upper limit on detection frequency that shows degradation beginning at frequencies of ~100 kHz in InGaAs/InP. Alternatively, germanium (Ge) single photon avalanche photodiodes (SPAD) have been reported to have more than an order of magnitude smaller charge trap densities than InGaAs/InP SPADs2, which allowed them to be successfully operated with passive quenching2 (i.e., no gated hold off times necessary), which is not possible with InGaAs/InP SPADs, indicating a much weaker dark count dependence on hold-off time consistent with fewer charge traps. Despite these encouraging results suggesting a possible higher operating frequency limit for Ge SPADs, little has been reported on Ge SPAD performance at high frequencies presumably because previous work with Ge SPADs has been discouraged by a strong demand to work at 1550 nm. NIR SPADs require cooling, which in the case of Ge SPADs dramatically reduces the quantum efficiency of the Ge at 1550 nm. Recently, however, advantages to working at 1310 nm have been suggested which combined with a need to increase quantum bit rates for quantum key distribution (QKD) motivates examination of Ge detectors performance at very high detection rates where InGaAs/InP does not perform as well. Presented in this paper are measurements of a commercially available Ge APD

  4. Least Reliable Bits Coding (LRBC) for high data rate satellite communications

    Science.gov (United States)

    Vanderaar, Mark; Wagner, Paul; Budinger, James

    1992-02-01

    An analysis and discussion of a bandwidth efficient multi-level/multi-stage block coded modulation technique called Least Reliable Bits Coding (LRBC) is presented. LRBC uses simple multi-level component codes that provide increased error protection on increasingly unreliable modulated bits in order to maintain an overall high code rate that increases spectral efficiency. Further, soft-decision multi-stage decoding is used to make decisions on unprotected bits through corrections made on more protected bits. Using analytical expressions and tight performance bounds it is shown that LRBC can achieve increased spectral efficiency and maintain equivalent or better power efficiency compared to that of Binary Phase Shift Keying (BPSK). Bit error rates (BER) vs. channel bit energy with Additive White Gaussian Noise (AWGN) are given for a set of LRB Reed-Solomon (RS) encoded 8PSK modulation formats with an ensemble rate of 8/9. All formats exhibit a spectral efficiency of 2.67 = (log2(8))(8/9) information bps/Hz. Bit by bit coded and uncoded error probabilities with soft-decision information are determined. These are traded with with code rate to determine parameters that achieve good performance. The relative simplicity of Galois field algebra vs. the Viterbi algorithm and the availability of high speed commercial Very Large Scale Integration (VLSI) for block codes indicates that LRBC using block codes is a desirable method for high data rate implementations.

  5. An Experimentally Validated SOA Model for High-Bit Rate System Applications

    Institute of Scientific and Technical Information of China (English)

    Hasan I. Saleheen

    2003-01-01

    A comprehensive model of the Semiconductor Optical Amplifier with experimental validation result is presented. This model accounts for various physical behavior of the device which is necessary for high bit-rate system application.

  6. Room temperature single-photon detectors for high bit rate quantum key distribution

    Energy Technology Data Exchange (ETDEWEB)

    Comandar, L. C.; Patel, K. A. [Toshiba Research Europe Ltd., 208 Cambridge Science Park, Milton Road, Cambridge CB4 0GZ (United Kingdom); Engineering Department, Cambridge University, 9 J J Thomson Ave., Cambridge CB3 0FA (United Kingdom); Fröhlich, B., E-mail: bernd.frohlich@crl.toshiba.co.uk; Lucamarini, M.; Sharpe, A. W.; Dynes, J. F.; Yuan, Z. L.; Shields, A. J. [Toshiba Research Europe Ltd., 208 Cambridge Science Park, Milton Road, Cambridge CB4 0GZ (United Kingdom); Penty, R. V. [Engineering Department, Cambridge University, 9 J J Thomson Ave., Cambridge CB3 0FA (United Kingdom)

    2014-01-13

    We report room temperature operation of telecom wavelength single-photon detectors for high bit rate quantum key distribution (QKD). Room temperature operation is achieved using InGaAs avalanche photodiodes integrated with electronics based on the self-differencing technique that increases avalanche discrimination sensitivity. Despite using room temperature detectors, we demonstrate QKD with record secure bit rates over a range of fiber lengths (e.g., 1.26 Mbit/s over 50 km). Furthermore, our results indicate that operating the detectors at room temperature increases the secure bit rate for short distances.

  7. Fast optical signal processing in high bit rate OTDM systems

    DEFF Research Database (Denmark)

    Poulsen, Henrik Nørskov; Jepsen, Kim Stokholm; Clausen, Anders;

    1998-01-01

    As all-optical signal processing is maturing, optical time division multiplexing (OTDM) has also gained interest for simple networking in high capacity backbone networks. As an example of a network scenario we show an OTDM bus interconnecting another OTDM bus, a single high capacity user...

  8. Achieving high bit rate logical stochastic resonance in a bistable system by adjusting parameters

    Science.gov (United States)

    Yang, Ding-Xin; Gu, Feng-Shou; Feng, Guo-Jin; Yang, Yong-Min; Ball, Andrew

    2015-11-01

    The phenomenon of logical stochastic resonance (LSR) in a nonlinear bistable system is demonstrated by numerical simulations and experiments. However, the bit rates of the logical signals are relatively low and not suitable for practical applications. First, we examine the responses of the bistable system with fixed parameters to different bit rate logic input signals, showing that an arbitrary high bit rate LSR in a bistable system cannot be achieved. Then, a normalized transform of the LSR bistable system is introduced through a kind of variable substitution. Based on the transform, it is found that LSR for arbitrary high bit rate logic signals in a bistable system can be achieved by adjusting the parameters of the system, setting bias value and amplifying the amplitudes of logic input signals and noise properly. Finally, the desired OR and AND logic outputs to high bit rate logic inputs in a bistable system are obtained by numerical simulations. The study might provide higher feasibility of LSR in practical engineering applications. Project supported by the National Natural Science Foundation of China (Grant No. 51379526).

  9. Achieving high bit rate logical stochastic resonance in a bistable system by adjusting parameters

    Institute of Scientific and Technical Information of China (English)

    杨定新; 谷丰收; 冯国金; 杨拥民

    2015-01-01

    The phenomenon of logical stochastic resonance (LSR) in a nonlinear bistable system is demonstrated by numerical simulations and experiments. However, the bit rates of the logical signals are relatively low and not suitable for practical applications. First, we examine the responses of the bistable system with fixed parameters to different bit rate logic input signals, showing that an arbitrary high bit rate LSR in a bistable system cannot be achieved. Then, a normalized transform of the LSR bistable system is introduced through a kind of variable substitution. Based on the transform, it is found that LSR for arbitrary high bit rate logic signals in a bistable system can be achieved by adjusting the parameters of the system, setting bias value and amplifying the amplitudes of logic input signals and noise properly. Finally, the desired OR and AND logic outputs to high bit rate logic inputs in a bistable system are obtained by numerical simulations. The study might provide higher feasibility of LSR in practical engineering applications.

  10. Dispersion Monitoring techniques in High Bit-rate Optical Communication Systems

    Institute of Scientific and Technical Information of China (English)

    SANG Xin-zhu; YU Chong-xiu; ZHANG Qi; WANG Xu

    2004-01-01

    For the efficient dynamic dispersion compensation, it is essential to monitor the dispersion accurately. The existing main dispersion monitoring techniques in high bit- rate optical communication systems are presented as well as their operating principles and research progress. The advantages and disadvantages of these methods are analyzed and discussed.

  11. High fidelity adaptive vector quantization at very low bit rates for progressive transmission of radiographic images

    Science.gov (United States)

    Mitra, Sunanda; Yang, Shu Y.

    1999-01-01

    An adaptive vector quantizer (VQ) using a clustering technique known as adaptive fuzzy leader clustering (AFLC) that is similar in concept to deterministic annealing for VQ codebook design has been developed. This vector quantizer, AFLC-VQ, has been designed to vector quantize wavelet decomposed sub images with optimal bit allocation. The high- resolution sub images at each level have been statistically analyzed to conform to generalized Gaussian probability distributions by selecting the optimal number of filter taps. The adaptive characteristics of AFLC-VQ result from AFLC, an algorithm that uses self-organizing neural networks with fuzzy membership values of the input samples for upgrading the cluster centroids based on well known optimization criteria. By generating codebooks containing codewords of varying bits, AFLC-VQ is capable of compressing large color/monochrome medical images at extremely low bit rates (0.1 bpp and less) and yet yielding high fidelity reconstructed images. The quality of the reconstructed images formed by AFLC-VQ has been compared with JPEG and EZW, the standard and the well known wavelet based compression technique (using scalar quantization), respectively, in terms of statistical performance criteria as well as visual perception. AFLC-VQ exhibits much better performance than the above techniques. JPEG and EZW were chosen as comparative benchmarks since these have been used in radiographic image compression. The superior performance of AFLC-VQ over LBG-VQ has been reported in earlier papers.

  12. low bit rate video coding low bit rate video coding

    African Journals Online (AJOL)

    eobe

    ariable length bit rate (VLBR) broadly encompasses video coding which broadly encompasses ... for motion estimation and compensation to reduce the prediction sation to reduce the ... a special interest among the video coding community ...

  13. Re-use of Low Bandwidth Equipment for High Bit Rate Transmission Using Signal Slicing Technique

    DEFF Research Database (Denmark)

    Wagner, Christoph; Spolitis, S.; Vegas Olmos, Juan José;

    : Massive fiber-to-the-home network deployment requires never ending equipment upgrades operating at higher bandwidth. We show effective signal slicing method, which can reuse low bandwidth opto-electronical components for optical communications at higher bit rates.......: Massive fiber-to-the-home network deployment requires never ending equipment upgrades operating at higher bandwidth. We show effective signal slicing method, which can reuse low bandwidth opto-electronical components for optical communications at higher bit rates....

  14. Design of pseudo-symmetric high bit rate, bend insensitive optical fiber applicable for high speed FTTH

    Science.gov (United States)

    Makouei, Somayeh; Koozekanani, Z. D.

    2014-12-01

    In this paper, with sophisticated modification on modal-field distribution and introducing new design procedure, the single-mode fiber with ultra-low bending-loss and pseudo-symmetric high bit-rate of uplink and downlink, appropriate for fiber-to-the-home (FTTH) operation is presented. The bending-loss reduction and dispersion management are done by the means of Genetic Algorithm. The remarkable feature of this methodology is designing a bend-insensitive fiber without reduction of core radius and MFD. Simulation results show bending loss of 1.27×10-2 dB/turn at 1.55 μm for 5 mm curvature radius. The MFD and Aeff are 9.03 μm and 59.11 μm2. Moreover, the upstream and downstream bit-rates are approximately 2.38 Gbit/s-km and 3.05 Gbit/s-km.

  15. 120 MB/S and 240 MB/S bit synchronizer-signal conditioners for NASA high data rate applications

    Science.gov (United States)

    Gray, J. S.

    1976-01-01

    Two bit synchronizer-signal conditioners (BSSC) developed for NASA high data rate applications such as earth resources monitoring are described. One BSSC is centered at 120 MB/s and the other at 240 Mb/s. These subsystems are featured out of the total hardware developed because the BSSC is such a key subsystem in determining overall system statistical performance. These units represent an evolution of high data rate BSSC's available at low data rates. Numerous inputs/outputs, control functions, indicators, plus the ability to minimize the effects of various signal perturbations are provided. Examples of allowed perturbations are input level variations, bit rate variance static and dynamic, baseline, transition density, bandlimiting, etc., as well as noise. Emphasis in the past has been primarily concerned only with noise.

  16. New high performance SAW convolvers used in high bit rate and wideband spread spectrum CDMA communications system.

    Science.gov (United States)

    Hikita, M; Takubo, C; Asai, K

    2000-01-01

    New surface acoustic wave (SAW) convolver structures with high conversion efficiency and self-temperature compensation characteristics have been developed. Strong piezoelectric substrates, regardless of temperature coefficients of delay (TCD), can be used in these convolvers. New demodulation techniques using the developed SAW convolver for high bit rate and wideband spread spectrum code division multiple access (CDMA) communications have also been developed. I- and Q-channel demodulation data can be derived directly from binary phase shift keying (BPSK) or quadri-phase shift keying (QPSK) CDMA signals. In an experiment using a 128 degrees YX-LiNbO(3) substrate, CDMA signals of 9 Mbps (megabits per second) with 60 Mcps (megachips per second) spread by 13-chip Barker code and 11 Mbps with 140 Mcps spread by 25-chip Shiba's code were clearly demodulated, demonstrating the effectiveness of these techniques for use in future CDMA communications.

  17. Simultaneous high bit-rate format and mode conversion with a single tilted apodized few-mode fiber Bragg grating

    Science.gov (United States)

    Gao, Ya; Sun, Junqiang; Sima, Chaotan

    2016-10-01

    We propose an all-optical approach for simultaneous high bit-rate return-to-zero (RZ) to non-return-to-zero (NRZ) format and LP01 to LP11 mode conversion using a weakly tilted apodized few-mode fiber Bragg grating (TA-FM-FBG) with specific linear spectral response. The grating apodization profile is designed by utilizing an efficient inverse scattering algorithm and the maximum refractive index modulation is adjusted based on the grating tilt angle, according to Coupled-Mode Theory. The temporal performance and operation bandwidth of the converter are discussed. The approach provides potential favorable device for the connection of various communication systems.

  18. Ultra low bit-rate speech coding

    CERN Document Server

    Ramasubramanian, V

    2015-01-01

    "Ultra Low Bit-Rate Speech Coding" focuses on the specialized topic of speech coding at very low bit-rates of 1 Kbits/sec and less, particularly at the lower ends of this range, down to 100 bps. The authors set forth the fundamental results and trends that form the basis for such ultra low bit-rates to be viable and provide a comprehensive overview of various techniques and systems in literature to date, with particular attention to their work in the paradigm of unit-selection based segment quantization. The book is for research students, academic faculty and researchers, and industry practitioners in the areas of speech processing and speech coding.

  19. Bit-error-rate testing of high-power 30-GHz traveling-wave tubes for ground-terminal applications

    Science.gov (United States)

    Shalkhauser, Kurt A.

    1987-01-01

    Tests were conducted at NASA Lewis to measure the bit-error-rate performance of two 30-GHz 200-W coupled-cavity traveling-wave tubes (TWTs). The transmission effects of each TWT on a band-limited 220-Mbit/s SMSK signal were investigated. The tests relied on the use of a recently developed digital simulation and evaluation system constructed at Lewis as part of the 30/20-GHz technology development program. This paper describes the approach taken to test the 30-GHz tubes and discusses the test data. A description of the bit-error-rate measurement system and the adaptations needed to facilitate TWT testing are also presented.

  20. Rate Control for MPEG-4 Bit Stream

    Institute of Scientific and Technical Information of China (English)

    王振洲; 李桂苓

    2003-01-01

    For a very long time video processing dealt exclusively with fixed-rate sequences of rectangular shaped images. However, interest has been recently moving toward a more flexible concept in which the subject of the processing and encoding operations is a set of visual elements organized in both time and space in a flexible and arbitrarily complex way. The moving picture experts group (MPEG-4) standard supports this concept and its verification model (VM) encoder has adopted scalable rate control (SRC) as the rate control scheme, which is based on the spatial domain and compatible with constant bit rate (CBR) and variable bit rate (VBR). In this paper,a new rate control algorithm based on the DCT domain instead of the pixel domain is presented. More-over, macroblock level rate control scheme to compute the quantization step for each macroblock has been adopted. The experimental results show that the new algorithm can achieve a much better result than the original one in both peak signal-to-noise ratio (PSNR) and the coding bits, and that the new algorithm is more flexible than test model 5 (TM5) rate control algorithm.

  1. Sleep stage classification with low complexity and low bit rate.

    Science.gov (United States)

    Virkkala, Jussi; Värri, Alpo; Hasan, Joel; Himanen, Sari-Leena; Müller, Kiti

    2009-01-01

    Standard sleep stage classification is based on visual analysis of central (usually also frontal and occipital) EEG, two-channel EOG, and submental EMG signals. The process is complex, using multiple electrodes, and is usually based on relatively high (200-500 Hz) sampling rates. Also at least 12 bit analog to digital conversion is recommended (with 16 bit storage) resulting in total bit rate of at least 12.8 kbit/s. This is not a problem for in-house laboratory sleep studies, but in the case of online wireless self-applicable ambulatory sleep studies, lower complexity and lower bit rates are preferred. In this study we further developed earlier single channel facial EMG/EOG/EEG-based automatic sleep stage classification. An algorithm with a simple decision tree separated 30 s epochs into wakefulness, SREM, S1/S2 and SWS using 18-45 Hz beta power and 0.5-6 Hz amplitude. Improvements included low complexity recursive digital filtering. We also evaluated the effects of a reduced sampling rate, reduced number of quantization steps and reduced dynamic range on the sleep data of 132 training and 131 testing subjects. With the studied algorithm, it was possible to reduce the sampling rate to 50 Hz (having a low pass filter at 90 Hz), and the dynamic range to 244 microV, with an 8 bit resolution resulting in a bit rate of 0.4 kbit/s. Facial electrodes and a low bit rate enables the use of smaller devices for sleep stage classification in home environments.

  2. Low-bit-rate subband image coding with matching pursuits

    Science.gov (United States)

    Rabiee, Hamid; Safavian, S. R.; Gardos, Thomas R.; Mirani, A. J.

    1998-01-01

    In this paper, a novel multiresolution algorithm for low bit-rate image compression is presented. High quality low bit-rate image compression is achieved by first decomposing the image into approximation and detail subimages with a shift-orthogonal multiresolution analysis. Then, at the coarsest resolution level, the coefficients of the transformation are encoded by an orthogonal matching pursuit algorithm with a wavelet packet dictionary. Our dictionary consists of convolutional splines of up to order two for the detail and approximation subbands. The intercorrelation between the various resolutions is then exploited by using the same bases from the dictionary to encode the coefficients of the finer resolution bands at the corresponding spatial locations. To further exploit the spatial correlation of the coefficients, the zero trees of wavelets (EZW) algorithm was used to identify the potential zero trees. The coefficients of the presentation are then quantized and arithmetic encoded at each resolution, and packed into a scalable bit stream structure. Our new algorithm is highly bit-rate scalable, and performs better than the segmentation based matching pursuit and EZW encoders at lower bit rates, based on subjective image quality and peak signal-to-noise ratio.

  3. Techniques of Very Low Bit-Rate Speech Coding1

    Institute of Scientific and Technical Information of China (English)

    CUIHuijuan; TANGKun; ZHAOMing; ZHANGXin

    2004-01-01

    Techniques of very low bit-rate speech coding,such as lower than 800 bps are presented in this paper. The techniques of multi-frame, multi-sub-band, multimodel, and vector quantization etc. are effective to decrease the bit-rate of vocoders based on a linear prediction model. These techniques bring the vocoder not only high quality of the reconstructed speech, but also robustness.Vocoders which apply those techniques can synthesize clear and intelligent speech with some naturalness. The mean DRT (Diagnostic rhyme test) score of an 800 bps vocoder is 89.2% and 86.3% for a 600 bps vocoder.

  4. Low bit rate near-transparent image coding

    Science.gov (United States)

    Zhu, Bin; Tewfik, Ahmed H.; Gerek, Oemer N.

    1995-04-01

    In this paper, we describe an improved version of our previous approach for low bit rate near- perceptually transparent image compression. The method exploits both frequency and spatial domain visual masking effects and uses a combination of Fourier and wavelet representations to encode different bands. The frequency domain masking model is based on the psychophysical masking experimental data of sinusoidal patterns while the spatial domain masking is computed with a modified version of Girod's model. A discrete cosine transform is used in conjunction with frequency domain masking to encode the low frequency subimages. The medium and high frequency subimages are encoded in the wavelet domain with spatial domain masking. The main improvement over our previous technique is that a better model is used to calculate the tolerable error level for the subimages in the wavelet domain, and a boundary control is used to prevent or reduce the ringing noise in the decoded image. This greatly improves the decoded image quality for the same coding bit rates. Experiments show the approach can achieve very high quality to nearly transparent compression at bit rates of 0.2 to 0.4 bits/pixel for the image Lena.

  5. Post-manufacturing, 17-times acceptable raw bit error rate enhancement, dynamic codeword transition ECC scheme for highly reliable solid-state drives, SSDs

    Science.gov (United States)

    Tanakamaru, Shuhei; Fukuda, Mayumi; Higuchi, Kazuhide; Esumi, Atsushi; Ito, Mitsuyoshi; Li, Kai; Takeuchi, Ken

    2011-04-01

    A dynamic codeword transition ECC scheme is proposed for highly reliable solid-state drives, SSDs. By monitoring the error number or the write/erase cycles, the ECC codeword dynamically increases from 512 Byte (+parity) to 1 KByte, 2 KByte, 4 KByte…32 KByte. The proposed ECC with a larger codeword decreases the failure rate after ECC. As a result, the acceptable raw bit error rate, BER, before ECC is enhanced. Assuming a NAND Flash memory which requires 8-bit correction in 512 Byte codeword ECC, a 17-times higher acceptable raw BER than the conventional fixed 512 Byte codeword ECC is realized for the mobile phone application without an interleaving. For the MP3 player, digital-still camera and high-speed memory card applications with a dual channel interleaving, 15-times higher acceptable raw BER is achieved. Finally, for the SSD application with 8 channel interleaving, 13-times higher acceptable raw BER is realized. Because the ratio of the user data to the parity bits is the same in each ECC codeword, no additional memory area is required. Note that the reliability of SSD is improved after the manufacturing without cost penalty. Compared with the conventional ECC with the fixed large 32 KByte codeword, the proposed scheme achieves a lower power consumption by introducing the "best-effort" type operation. In the proposed scheme, during the most of the lifetime of SSD, a weak ECC with a shorter codeword such as 512 Byte (+parity), 1 KByte and 2 KByte is used and 98% lower power consumption is realized. At the life-end of SSD, a strong ECC with a 32 KByte codeword is used and the highly reliable operation is achieved. The random read performance is also discussed. The random read performance is estimated by the latency. The latency is below 1.5 ms for ECC codeword up to 32 KByte. This latency is below the average latency of 15,000 rpm HDD, 2 ms.

  6. Rate Distortion Analysis and Bit Allocation Scheme for Wavelet Lifting-Based Multiview Image Coding

    Science.gov (United States)

    Lasang, Pongsak; Kumwilaisak, Wuttipong

    2009-12-01

    This paper studies the distortion and the model-based bit allocation scheme of wavelet lifting-based multiview image coding. Redundancies among image views are removed by disparity-compensated wavelet lifting (DCWL). The distortion prediction of the low-pass and high-pass subbands of each image view from the DCWL process is analyzed. The derived distortion is used with different rate distortion models in the bit allocation of multiview images. Rate distortion models including power model, exponential model, and the proposed combining the power and exponential models are studied. The proposed rate distortion model exploits the accuracy of both power and exponential models in a wide range of target bit rates. Then, low-pass and high-pass subbands are compressed by SPIHT (Set Partitioning in Hierarchical Trees) with a bit allocation solution. We verify the derived distortion and the bit allocation with several sets of multiview images. The results show that the bit allocation solution based on the derived distortion and our bit allocation scheme provide closer results to those of the exhaustive search method in both allocated bits and peak-signal-to-noise ratio (PSNR). It also outperforms the uniform bit allocation and uniform bit allocation with normalized energy in the order of 1.7-2 and 0.3-1.4 dB, respectively.

  7. Enhanced bit rate-distance product impulse radio ultra-wideband over fiber link

    DEFF Research Database (Denmark)

    Rodes Lopez, Roberto; Jensen, Jesper Bevensee; Caballero Jambrina, Antonio

    2010-01-01

    We report on a record distance and bit rate-wireless impulse radio (IR) ultra-wideband (UWB) link with combined transmission over a 20 km long fiber link. We are able to improve the compliance with the regulated frequency emission mask and achieve bit rate-distance products as high as 16 Gbit/s·m....

  8. Warped Discrete Cosine Transform-Based Low Bit-Rate Block Coding Using Image Downsampling

    Directory of Open Access Journals (Sweden)

    Ertürk Sarp

    2007-01-01

    Full Text Available This paper presents warped discrete cosine transform (WDCT-based low bit-rate block coding using image downsampling. While WDCT aims to improve the performance of conventional DCT by frequency warping, the WDCT has only been applicable to high bit-rate coding applications because of the overhead required to define the parameters of the warping filter. Recently, low bit-rate block coding based on image downsampling prior to block coding followed by upsampling after the decoding process is proposed to improve the compression performance for low bit-rate block coders. This paper demonstrates that a superior performance can be achieved if WDCT is used in conjunction with image downsampling-based block coding for low bit-rate applications.

  9. Towards the generation of random bits at terahertz rates based on a chaotic semiconductor laser

    Science.gov (United States)

    Kanter, Ido; Aviad, Yaara; Reidler, Igor; Cohen, Elad; Rosenbluh, Michael

    2010-06-01

    Random bit generators (RBGs) are important in many aspects of statistical physics and crucial in Monte-Carlo simulations, stochastic modeling and quantum cryptography. The quality of a RBG is measured by the unpredictability of the bit string it produces and the speed at which the truly random bits can be generated. Deterministic algorithms generate pseudo-random numbers at high data rates as they are only limited by electronic hardware speed, but their unpredictability is limited by the very nature of their deterministic origin. It is widely accepted that the core of any true RBG must be an intrinsically non-deterministic physical process, e.g. measuring thermal noise from a resistor. Owing to low signal levels, such systems are highly susceptible to bias, introduced by amplification, and to small nonrandom external perturbations resulting in a limited generation rate, typically less than 100M bit/s. We present a physical random bit generator, based on a chaotic semiconductor laser, having delayed optical feedback, which operates reliably at rates up to 300Gbit/s. The method uses a high derivative of the digitized chaotic laser intensity and generates the random sequence by retaining a number of the least significant bits of the high derivative value. The method is insensitive to laser operational parameters and eliminates the necessity for all external constraints such as incommensurate sampling rates and laser external cavity round trip time. The randomness of long bit strings is verified by standard statistical tests.

  10. Framed bit error rate testing for 100G ethernet equipment

    DEFF Research Database (Denmark)

    Rasmussen, Anders; Ruepp, Sarah Renée; Berger, Michael Stübert

    2010-01-01

    The Internet users behavioural patterns are migrating towards bandwidth-intensive applications, which require a corresponding capacity extension. The emerging 100 Gigabit Ethernet (GE) technology is a promising candidate for providing a ten-fold increase of todays available Internet transmission...... rate. As the need for 100 Gigabit Ethernet equipment rises, so does the need for equipment, which can properly test these systems during development, deployment and use. This paper presents early results from a work-in-progress academia-industry collaboration project and elaborates on the challenges...... of performing bit error rate testing at 100Gbps. In particular, we show how Bit Error Rate Testing (BERT) can be performed over an aggregated 100G Attachment Unit Interface (CAUI) by encapsulating the test data in Ethernet frames at line speed. Our results show that framed bit error rate testing can...

  11. Comodulation masking release in bit-rate reduction systems

    DEFF Research Database (Denmark)

    Vestergaard, Martin David; Rasmussen, Karsten Bo; Poulsen, Torben

    1999-01-01

    It has been suggested that the level dependence of the upper masking slope be utilized in perceptual models in bit-rate reduction systems. However, comodulation masking release (CMR) phenomena lead to a reduction of the masking effect when a masker and a probe signal are amplitude modulated...... with the same frequency. In bit-rate reduction systems the masker would be the audio signal and the probe signal would represent the quantization noise. Masking curves have been determined for sinusoids and 1-Bark-wide noise maskers in order to investigate the risk of CMR, when quantizing depths are fixed.......75. A CMR of up to 10 dB was obtained at a distance of 6 Bark above the masker. The amount of CMR was found to depend on the presentation level of the masker; a higher masker level leads to a higher CMR effect. Hence, the risk of CMR affecting the subjective performance of bit-rate reduction systems cannot...

  12. Comodulation masking release in bit-rate reduction systems

    DEFF Research Database (Denmark)

    Vestergaard, Martin D.; Rasmussen, Karsten Bo; Poulsen, Torben

    1999-01-01

    It has been suggested that the level dependence of the upper masking slopebe utilised in perceptual models in bit-rate reduction systems. However,comodulation masking release (CMR) phenomena lead to a reduction of themasking effect when a masker and a probe signal are amplitude modulated withthe...... same frequency. In bit-rate reduction systems the masker would be theaudio signal and the probe signal would represent the quantization noise.Masking curves have been determined for sinusoids and 1-Bark-wide noisemaskers in order to investigate the risk of CMR, when quantizing depths arefixed...

  13. Modeling of Bit Error Rate in Cascaded 2R Regenerators

    DEFF Research Database (Denmark)

    Öhman, Filip; Mørk, Jesper

    2006-01-01

    This paper presents a simple and efficient model for estimating the bit error rate in a cascade of optical 2R-regenerators. The model includes the influences of of amplifier noise, finite extinction ratio and nonlinear reshaping. The interplay between the different signal impairments and the rege......This paper presents a simple and efficient model for estimating the bit error rate in a cascade of optical 2R-regenerators. The model includes the influences of of amplifier noise, finite extinction ratio and nonlinear reshaping. The interplay between the different signal impairments...

  14. A FAST BIT-LOADING ALGORITHM FOR HIGH SPEED POWER LINE COMMUNICATIONS

    Institute of Scientific and Technical Information of China (English)

    Zhang Shengqing; Zhao Li; Zou Cairong

    2012-01-01

    Adaptive bit-loading is a key technology in high speed power line communications with the Orthogonal Frequency Division Multiplexing (OFDM) modulation technology.According to the real situation of the transmitting power spectrum limited in high speed power line communications,this paper explored the adaptive bit loading algorithm to maximize transmission bit number when transmitting power spectral density and bit error rate are not exceed upper limit.With the characteristics of the power line channel,first of all,it obtains the optimal bit loading algorithm,and then provides the improved algorithm to reduce the computational complexity.Based on the analysis and simulation,it offers a non-iterative bit allocation algorithm,and finally the simulation shows that this new algorithm can greatly reduce the computational complexity,and the actual bit allocation results close to optimal.

  15. Biometric Quantization through Detection Rate Optimized Bit Allocation

    Science.gov (United States)

    Chen, C.; Veldhuis, R. N. J.; Kevenaar, T. A. M.; Akkermans, A. H. M.

    2009-12-01

    Extracting binary strings from real-valued biometric templates is a fundamental step in many biometric template protection systems, such as fuzzy commitment, fuzzy extractor, secure sketch, and helper data systems. Previous work has been focusing on the design of optimal quantization and coding for each single feature component, yet the binary string—concatenation of all coded feature components—is not optimal. In this paper, we present a detection rate optimized bit allocation (DROBA) principle, which assigns more bits to discriminative features and fewer bits to nondiscriminative features. We further propose a dynamic programming (DP) approach and a greedy search (GS) approach to achieve DROBA. Experiments of DROBA on the FVC2000 fingerprint database and the FRGC face database show good performances. As a universal method, DROBA is applicable to arbitrary biometric modalities, such as fingerprint texture, iris, signature, and face. DROBA will bring significant benefits not only to the template protection systems but also to the systems with fast matching requirements or constrained storage capability.

  16. Biometric Quantization through Detection Rate Optimized Bit Allocation

    Directory of Open Access Journals (Sweden)

    C. Chen

    2009-01-01

    Full Text Available Extracting binary strings from real-valued biometric templates is a fundamental step in many biometric template protection systems, such as fuzzy commitment, fuzzy extractor, secure sketch, and helper data systems. Previous work has been focusing on the design of optimal quantization and coding for each single feature component, yet the binary string—concatenation of all coded feature components—is not optimal. In this paper, we present a detection rate optimized bit allocation (DROBA principle, which assigns more bits to discriminative features and fewer bits to nondiscriminative features. We further propose a dynamic programming (DP approach and a greedy search (GS approach to achieve DROBA. Experiments of DROBA on the FVC2000 fingerprint database and the FRGC face database show good performances. As a universal method, DROBA is applicable to arbitrary biometric modalities, such as fingerprint texture, iris, signature, and face. DROBA will bring significant benefits not only to the template protection systems but also to the systems with fast matching requirements or constrained storage capability.

  17. Optical Switching and Bit Rates of 40 Gbit/s and above

    DEFF Research Database (Denmark)

    Ackaert, A.; Demester, P.; O'Mahony, M.;

    2003-01-01

    Optical switching in WDM networks introduces additional aspects to the choice of single channel bit rates compared to WDM transmission systems. The mutual impact of optical switching and bit rates of 40 Gbps and above is discussed.......Optical switching in WDM networks introduces additional aspects to the choice of single channel bit rates compared to WDM transmission systems. The mutual impact of optical switching and bit rates of 40 Gbps and above is discussed....

  18. Rate distortion optimal bit allocation methods for volumetric data using JPEG 2000.

    Science.gov (United States)

    Kosheleva, Olga M; Usevitch, Bryan E; Cabrera, Sergio D; Vidal, Edward

    2006-08-01

    Computer modeling programs that generate three-dimensional (3-D) data on fine grids are capable of generating very large amounts of information. These data sets, as well as 3-D sensor/measured data sets, are prime candidates for the application of data compression algorithms. A very flexible and powerful compression algorithm for imagery data is the newly released JPEG 2000 standard. JPEG 2000 also has the capability to compress volumetric data, as described in Part 2 of the standard, by treating the 3-D data as separate slices. As a decoder standard, JPEG 2000 does not describe any specific method to allocate bits among the separate slices. This paper proposes two new bit allocation algorithms for accomplishing this task. The first procedure is rate distortion optimal (for mean squared error), and is conceptually similar to postcompression rate distortion optimization used for coding codeblocks within JPEG 2000. The disadvantage of this approach is its high computational complexity. The second bit allocation algorithm, here called the mixed model (MM) approach, mathematically models each slice's rate distortion curve using two distinct regions to get more accurate modeling at low bit rates. These two bit allocation algorithms are applied to a 3-D Meteorological data set. Test results show that the MM approach gives distortion results that are nearly identical to the optimal approach, while significantly reducing computational complexity.

  19. An Improved Frame-Layer Bit Allocation Scheme for H.264/AVC Rate Control

    Institute of Scientific and Technical Information of China (English)

    LIN Gui-xu; ZHENG Shi-bao; ZHU Liang-jia

    2009-01-01

    In this paper, we aim at improving the video quality degradation due to high motions or scene changes. An improved frame-layer bit allocation scheme for H.264/AVC rate control is proposed. First, current frame is pre-encoded in 16×16 modes with a fixed quantization parameter (QP). The frame coding complexity is then measured based on the resulting bits and peak signal-to-ratio (PSNR) in the pre-coding stage. Finally, a bit budgetis calculated for current frame according to its coding complexity and inter-frame PSNR fluctuation, combined with the buffer status. Simulation results show that, in comparison with the H.264 adopted rate control scheme, our method is more efficient to suppress the sharp PSNR drops caused by high motions and scene changes. The visual quality variations in a sequence are also relieved.

  20. Efficient rate control scheme for low bit rate H.264/AVC video coding

    Institute of Scientific and Technical Information of China (English)

    LI Zhi-cheng; ZHANG Yong-jun; LIU Tao; GU Wan-yi

    2009-01-01

    This article presents an efficient rate control scheme for H.264/AVC video coding in low bit rate environment. In the proposed scheme, an improved rate-distortion (RD) model by both analytical and empirical approaches is developed. It involves an enhanced mean absolute difference estimating method and a more rate-robust distortion model. Based on this RD model, an efficient macroblock-layer rate control scheme for H.264/AVC video coding is proposed. Experimental results show that this model encodes video sequences with higher peak signal-to-noise ratio gains and generates bit stream closer to the target rate.

  1. Measurements of Aperture Averaging on Bit-Error-Rate

    Science.gov (United States)

    Bastin, Gary L.; Andrews, Larry C.; Phillips, Ronald L.; Nelson, Richard A.; Ferrell, Bobby A.; Borbath, Michael R.; Galus, Darren J.; Chin, Peter G.; Harris, William G.; Marin, Jose A.; Burdge, Geoffrey L.; Wayne, David; Pescatore, Robert

    2005-01-01

    We report on measurements made at the Shuttle Landing Facility (SLF) runway at Kennedy Space Center of receiver aperture averaging effects on a propagating optical Gaussian beam wave over a propagation path of 1,000 in. A commercially available instrument with both transmit and receive apertures was used to transmit a modulated laser beam operating at 1550 nm through a transmit aperture of 2.54 cm. An identical model of the same instrument was used as a receiver with a single aperture that was varied in size up to 20 cm to measure the effect of receiver aperture averaging on Bit Error Rate. Simultaneous measurements were also made with a scintillometer instrument and local weather station instruments to characterize atmospheric conditions along the propagation path during the experiments.

  2. A Contourlet-Based Embedded Image Coding Scheme on Low Bit-Rate

    Science.gov (United States)

    Song, Haohao; Yu, Songyu

    Contourlet transform (CT) is a new image representation method, which can efficiently represent contours and textures in images. However, CT is a kind of overcomplete transform with a redundancy factor of 4/3. If it is applied to image compression straightforwardly, the encoding bit-rate may increase to meet a given distortion. This fact baffles the coding community to develop CT-based image compression techniques with satisfactory performance. In this paper, we analyze the distribution of significant contourlet coefficients in different subbands and propose a new contourlet-based embedded image coding (CEIC) scheme on low bit-rate. The well-known wavelet-based embedded image coding (WEIC) algorithms such as EZW, SPIHT and SPECK can be easily integrated into the proposed scheme by constructing a virtual low frequency subband, modifying the coding framework of WEIC algorithms according to the structure of contourlet coefficients, and adopting a high-efficiency significant coefficient scanning scheme for CEIC scheme. The proposed CEIC scheme can provide an embedded bit-stream, which is desirable in heterogeneous networks. Our experiments demonstrate that the proposed scheme can achieve the better compression performance on low bit-rate. Furthermore, thanks to the contourlet adopted in the proposed scheme, more contours and textures in the coded images are preserved to ensure the superior subjective quality.

  3. Video Synchronization With Bit-Rate Signals and Correntropy Function

    Directory of Open Access Journals (Sweden)

    Igor Pereira

    2017-09-01

    Full Text Available We propose an approach for the synchronization of video streams using correntropy. Essentially, the time offset is calculated on the basis of the instantaneous transfer rates of the video streams that are extracted in the form of a univariate signal known as variable bit-rate (VBR. The state-of-the-art approach uses a window segmentation strategy that is based on consensual zero-mean normalized cross-correlation (ZNCC. This strategy has an elevated computational complexity, making its application to synchronizing online data streaming difficult. Hence, our proposal uses a different window strategy that, together with the correntropy function, allows the synchronization to be performed for online applications. This provides equivalent synchronization scores with a rapid offset determination as the streams come into the system. The efficiency of our approach has been verified through experiments that demonstrate its viability with values that are as precise as those obtained by ZNCC. The proposed approach scored 81 % in time reference classification against the equivalent 81 % of the state-of-the-art approach, requiring much less computational power.

  4. Effects of hydraulic parameter cleaning variations on rate of penetration of soft formation insert bits

    Energy Technology Data Exchange (ETDEWEB)

    Doiron, H.H.; Deane, J.D.

    1982-09-01

    Effects of hydraulic cleaning parameter variations on rate of penetration response of 7 7/8 inch diameter soft formation insert bits have been measured in laboratory drilling tests. Tests were conducted in Mancos Shale rock samples at 700 psi and 4000 psi simulated overbalance pressure conditions using a 9.1 pound per gallon bentonite-barite water base drilling fluid. Bit hydraulic horsepower was varied from 0.72 to 9.5 HHP/in/sup 2/ using two or three nozzles in sizes ranging from 9/32 to 14/32 inches in diameter. Some improvements in ROP at constant bit hydraulic horsepower and impact force levels were obtained with two nozzle configurations vs. three nozzle configurations, but improvements were not consistently out of the range of normal test to test variations. Reduction in drilling costs due to the measured response of ROP to improved hydraulic cleaning is compared to increased operating costs required to provide additional hydraulics. Results indicate that bit hydraulic horsepower levels in excess of popular rules of thumb are cost effective in slow drilling due to high overbalance pressure.

  5. Improved DCT-based image coding and decoding methods for low-bit-rate applications

    Science.gov (United States)

    Jung, Sung-Hwan; Mitra, Sanjit K.

    1994-05-01

    The discrete cosine transform (DCT) is well known for highly efficient coding performance, and it is widely used in many image compression applications. However, in low-bit rate coding, it produces undesirable block artifacts that are visually not pleasing. In addition, in many applications, faster compression and easier VLSI implementation of DCT coefficients are also important issues. The removal of the block artifacts and faster DCT computation are therefore of practical interest. In this paper, we outline a modified DCT computation scheme that provides a simple efficient solution to the reduction of the block artifacts while achieving faster computation. We also derive a similar solution for the efficient computation of the inverse DCT. We have applied the new approach for the low-bit rate coding and decoding of images. Initial simulation results on real images have verified the improved performance obtained using the proposed method over the standard JPEG method.

  6. Up to 20 Gbit/s bit-rate transparent integrated interferometric wavelength converter

    DEFF Research Database (Denmark)

    Jørgensen, Carsten; Danielsen, Søren Lykke; Hansen, Peter Bukhave;

    1996-01-01

    We present a compact and optimised multiquantum-well based, integrated all-active Michelson interferometer for 26 Gbit/s optical wavelength conversion. Bit-rate transparent operation is demonstrated with a conversion penalty well below 0.5 dB at bit-rates ranging from 622 Mbit/s to 20 Gbit/s....

  7. Mutual information, bit error rate and security in W\\'{o}jcik's scheme

    CERN Document Server

    Zhang, Z

    2004-01-01

    In this paper the correct calculations of the mutual information of the whole transmission, the quantum bit error rate (QBER) are presented. Mistakes of the general conclusions relative to the mutual information, the quantum bit error rate (QBER) and the security in W\\'{o}jcik's paper [Phys. Rev. Lett. {\\bf 90}, 157901(2003)] have been pointed out and corrected.

  8. Application of time-hopping UWB range-bit rate performance in the UWB sensor networks

    NARCIS (Netherlands)

    Nascimento, J.R.V. do; Nikookar, H.

    2008-01-01

    In this paper, the achievable range-bit rate performance is evaluated for Time-Hopping (TH) UWB networks complying with the FCC outdoor emission limits in the presence of Multiple Access Interference (MAI). Application of TH-UWB range-bit rate performance is presented for UWB sensor networks. Result

  9. Consideration of Direct Bit-Rate Measuring Method based on Extracting Envelope Signal

    Science.gov (United States)

    Otani, Akihito; Tsuda, Yukio; Igawa, Koji; Shida, Katsunori

    We previously developed an optical sampling oscilloscope (EDT-OSO) based on an envelope detection triggering method. This EDT-OSO can stably measure eye-diagram waveforms of signals exceeding 100Gbps without an external high-frequency clock signal. However far-end waveform measurements during a long distance place could not be realized. Because the EDT-OSO requires to link 10-MHz time bases in the EDT-OSO and a light under test (LUT) generator for synchrinizing. To overcom this drawbak, we developed a direct bit-rate measureing method for synchronizing both 10-MHz time bases vartually and a self-synchronized EDT-OSO (SSEDT-OSO) based on this method simulteniously. We confirmed that a bit-rate measurement repetability of the SSEDT-OSO was from 10-9 to 10-8 by evaluating a standard deviation and the SSEDT-OSO could measure an eye-diagram without linking 10-MHz time bases. This paper explains the basic principle for measuring the bit-rate of the LUT directly. Furthermore, we describe a configuration of the SSEDT-OSO and evalluation results.

  10. HIGH-POWER TURBODRILL AND DRILL BIT FOR DRILLING WITH COILED TUBING

    Energy Technology Data Exchange (ETDEWEB)

    Robert Radtke; David Glowka; Man Mohan Rai; David Conroy; Tim Beaton; Rocky Seale; Joseph Hanna; Smith Neyrfor; Homer Robertson

    2008-03-31

    Commercial introduction of Microhole Technology to the gas and oil drilling industry requires an effective downhole drive mechanism which operates efficiently at relatively high RPM and low bit weight for delivering efficient power to the special high RPM drill bit for ensuring both high penetration rate and long bit life. This project entails developing and testing a more efficient 2-7/8 in. diameter Turbodrill and a novel 4-1/8 in. diameter drill bit for drilling with coiled tubing. The high-power Turbodrill were developed to deliver efficient power, and the more durable drill bit employed high-temperature cutters that can more effectively drill hard and abrasive rock. This project teams Schlumberger Smith Neyrfor and Smith Bits, and NASA AMES Research Center with Technology International, Inc (TII), to deliver a downhole, hydraulically-driven power unit, matched with a custom drill bit designed to drill 4-1/8 in. boreholes with a purpose-built coiled tubing rig. The U.S. Department of Energy National Energy Technology Laboratory has funded Technology International Inc. Houston, Texas to develop a higher power Turbodrill and drill bit for use in drilling with a coiled tubing unit. This project entails developing and testing an effective downhole drive mechanism and a novel drill bit for drilling 'microholes' with coiled tubing. The new higher power Turbodrill is shorter, delivers power more efficiently, operates at relatively high revolutions per minute, and requires low weight on bit. The more durable thermally stable diamond drill bit employs high-temperature TSP (thermally stable) diamond cutters that can more effectively drill hard and abrasive rock. Expectations are that widespread adoption of microhole technology could spawn a wave of 'infill development' drilling of wells spaced between existing wells, which could tap potentially billions of barrels of bypassed oil at shallow depths in mature producing areas. At the same time, microhole

  11. Design and Performance Evaluation of Contention Resolution Schemes with QoS Support for Multimedia Traffic in High Bit-Rate Wireless Communications

    Science.gov (United States)

    Srichavengsup, Warakorn; Charoenpanichkit, Akkarapat; Wuttisittikulkij, Lunchakorn

    This paper considers the problem of contention resolution algorithm for multi-class with quality of service (QoS) constrained for wireless communication. Five different channel reservation schemes are proposed, namely, UNI+MLA, UNI+DS, UNI+DS+MLA, Partial UNI and Partial UNI+MLA schemes for multimedia traffic, all are extensions of our recently proposed UNI scheme for single-class traffic. The goal is to achieve the highest system performance and enable each traffic type to meet its QoS requirements. We evaluate the performance of each scheme by mathematical analysis. The numerical results show that our proposed schemes are effective in enabling each traffic type to achieve the best successful rate possible in this kind of environment. Finally when comparing between our proposed schemes and conventional technique in terms of both throughput performance and QoS requirements it is found that the UNI+MLA, UNI+DS+MLA and Partial UNI+MLA schemes are relatively efficient and suitable for practical applications.

  12. Bit error rate testing of fiber optic data links for MMIC-based phased array antennas

    Science.gov (United States)

    Shalkhauser, K. A.; Kunath, R. R.; Daryoush, A. S.

    1990-06-01

    The measured bit-error-rate (BER) performance of a fiber optic data link to be used in satellite communications systems is presented and discussed. In the testing, the link was measured for its ability to carry high burst rate, serial-minimum shift keyed (SMSK) digital data similar to those used in actual space communications systems. The fiber optic data link, as part of a dual-segment injection-locked RF fiber optic link system, offers a means to distribute these signals to the many radiating elements of a phased array antenna. Test procedures, experimental arrangements, and test results are presented.

  13. Theoretical Study of Quantum Bit Rate in Free-Space Quantum Cryptography

    Institute of Scientific and Technical Information of China (English)

    MA Jing; ZHANG Guang-Yu; TAN Li-Ying

    2006-01-01

    The quantum bit rate is an important operating parameter in free-space quantum key distribution. We introduce the measuring factor and the sifting factor, and present the expressions of the quantum bit rate based on the ideal single-photon sources and the single-photon sources with Poisson distribution. The quantum bit rate is studied in the numerical simulation for the laser links between a ground station and a satellite in a low earth orbit. The results show that it is feasible to implement quantum key distribution between a ground station and a satellite in a low earth orbit.

  14. Entropy rates of low-significance bits sampled from chaotic physical systems

    Science.gov (United States)

    Corron, Ned J.; Cooper, Roy M.; Blakely, Jonathan N.

    2016-10-01

    We examine the entropy of low-significance bits in analog-to-digital measurements of chaotic dynamical systems. We find the partition of measurement space corresponding to low-significance bits has a corrugated structure. Using simulated measurements of a map and experimental data from a circuit, we identify two consequences of this corrugated partition. First, entropy rates for sequences of low-significance bits more closely approach the metric entropy of the chaotic system, because the corrugated partition better approximates a generating partition. Second, accurate estimation of the entropy rate using low-significance bits requires long block lengths as the corrugated partition introduces more long-term correlation, and using only short block lengths overestimates the entropy rate. This second phenomenon may explain recent reports of experimental systems producing binary sequences that pass statistical tests of randomness at rates that may be significantly beyond the metric entropy rate of the physical source.

  15. Context-Adaptive Arithmetic Coding Scheme for Lossless Bit Rate Reduction of MPEG Surround in USAC

    Science.gov (United States)

    Yoon, Sungyong; Pang, Hee-Suk; Sung, Koeng-Mo

    We propose a new coding scheme for lossless bit rate reduction of the MPEG Surround module in unified speech and audio coding (USAC). The proposed scheme is based on context-adaptive arithmetic coding for efficient bit stream composition of spatial parameters. Experiments show that it achieves the significant lossless bit reduction of 9.93% to 12.14% for spatial parameters and 8.64% to 8.96% for the overall MPEG Surround bit streams compared to the original scheme. The proposed scheme, which is not currently included in USAC, can be used for the improved coding efficiency of MPEG Surround in USAC, where the saved bits can be utilized by the other modules in USAC.

  16. Digital PSK to BiO-L demodulator for 2 sup nx(bit rate) carrier

    Science.gov (United States)

    Shull, T. A.

    1979-01-01

    A phase shift key (PSK) to BiO-L demodulator which uses standard digital integrated circuits is discussed. The demodulator produces NRZ-L, bit clock, and BiO-L outputs from digital PSK input signals for which the carrier is a 2 to the Nth multiple of the bit rate. Various bit and carrier rates which are accommodated by changing various component values within the demodulator are described. The use of the unit for sinusoidal inputs as well as digital inputs is discussed.

  17. Study of bit error rate (BER) for multicarrier OFDM

    Science.gov (United States)

    Alshammari, Ahmed; Albdran, Saleh; Matin, Mohammad

    2012-10-01

    Orthogonal Frequency Division Multiplexing (OFDM) is a multicarrier technique that is being used more and more in recent wideband digital communications. It is known for its ability to handle severe channel conditions, the efficiency of spectral usage and the high data rate. Therefore, It has been used in many wired and wireless communication systems such as DSL, wireless networks and 4G mobile communications. Data streams are modulated and sent over multiple subcarriers using either M-QAM or M-PSK. OFDM has lower inter simple interference (ISI) levels because of the of the low data rates of carriers resulting in long symbol periods. In this paper, BER performance of OFDM with respect to signal to noise ratio (SNR) is evaluated. BPSK Modulation is used in s Simulation based system in order to get the BER over different wireless channels. These channels include additive white Gaussian Noise (AWGN) and fading channels that are based on Doppler spread and Delay spread. Plots of the results are compared with each other after varying some of the key parameters of the system such as the IFFT, number of carriers, SNR. The results of the simulation give visualization of what kind of BER to expect when the signal goes through those channels.

  18. A novel dynamic frame rate control algorithm for H.264 low-bit-rate video coding

    Institute of Scientific and Technical Information of China (English)

    Yang Jing; Fang Xiangzhong

    2007-01-01

    The goal of this paper is to improve human visual perceptual quality as well as coding efficiency of H.264 video at low bit rate conditions by adaptively adjusting the number of skipped frames. The encoding frames ale selected according to the motion activity of each frame and the motion accumulation of successive frames. The motion activity analysis is based on the statistics of motion vectors and with consideration of the characteristics of H. 264 coding standard. A prediction model of motion accumulation is proposed to reduce complex computation of motion estimation. The dynamic encoding frame rate control algorithm is applied to both the frame level and the GOB (Group of Macroblocks) level. Simulation is done to compare the performance of JM76 with the proposed frame level scheme and GOB level scheme.

  19. All-optical repetition rate multiplication of pseudorandom bit sequences based on cascaded TOADs

    Science.gov (United States)

    Sun, Zhenchao; Wang, Zhi; Wu, Chongqing; Wang, Fu; Li, Qiang

    2016-03-01

    A scheme for all-optical repetition rate multiplication of pseudorandom bit sequences (PRBS) is demonstrated with all-optical wavelength conversion and optical logic gate 'OR' based on cascaded Tera-Hertz Optical Asymmetric Demultiplexers (TOADs). Its feasibility is verified by multiplication experiments from 500 Mb/s to 4 Gb/s for 23-1 PRBS and from 1 Gb/s to 4 Gb/s for 27-1 PRBS. This scheme can be employed for rate multiplication for much longer cycle PRBS at much higher bit rate over 40 Gb/s when the time-delay, the loss and the dispersion of the optical delay line are all precisely managed. The upper limit of bit rate will be restricted by the recovery time of semiconductor optical amplifier (SOA) finally.

  20. Threshold-Based Bit Error Rate for Stopping Iterative Turbo Decoding in a Varying SNR Environment

    Science.gov (United States)

    Mohamad, Roslina; Harun, Harlisya; Mokhtar, Makhfudzah; Adnan, Wan Azizun Wan; Dimyati, Kaharudin

    2017-01-01

    Online bit error rate (BER) estimation (OBE) has been used as a stopping iterative turbo decoding criterion. However, the stopping criteria only work at high signal-to-noise ratios (SNRs), and fail to have early termination at low SNRs, which contributes to an additional iteration number and an increase in computational complexity. The failure of the stopping criteria is caused by the unsuitable BER threshold, which is obtained by estimating the expected BER performance at high SNRs, and this threshold does not indicate the correct termination according to convergence and non-convergence outputs (CNCO). Hence, in this paper, the threshold computation based on the BER of CNCO is proposed for an OBE stopping criterion (OBEsc). From the results, OBEsc is capable of terminating early in a varying SNR environment. The optimum number of iterations achieved by the OBEsc allows huge savings in decoding iteration number and decreasing the delay of turbo iterative decoding.

  1. Entanglement enhanced bit rate over multiple uses of a lossy bosonic channel with memory

    Science.gov (United States)

    Lupo, C.; Mancini, S.

    2010-03-01

    We present a study of the achievable rates for classical information transmission via a lossy bosonic channel with memory, using homodyne detection. A comparison with the memoryless case shows that the presence of memory enhances the bit rate if information is encoded in collective states, i.e., states which are entangled over different uses of the channel.

  2. On Bit Rate Reduction of Inter-Channel Communication for a Binaural Hearing Assistance System

    Science.gov (United States)

    Chisaki, Yoshifumi; Kawano, Ryouji; Usagawa, Tsuyoshi

    A binaural hearing assistance system based on the frequency domain binaural model has been previously proposed. The system can enhance a signal coming from a specific direction. Since the system utilizes a binaural signal, an inter-channel communication between left and right subsystems is required. The bit rate reduction in inter-channel communication is essential for the detachment of the headset from the processing system. In this paper, the performance of a system which uses a differential pulse code modulation codec is examined and the relationship between the bit rate and sound quality is discussed.

  3. Analytical expression for the bit error rate of cascaded all-optical regenerators

    DEFF Research Database (Denmark)

    Mørk, Jesper; Öhman, Filip; Bischoff, S.

    2003-01-01

    We derive an approximate analytical expression for the bit error rate of cascaded fiber links containing all-optical 2R-regenerators. A general analysis of the interplay between noise due to amplification and the degree of reshaping (nonlinearity) of the regenerator is performed.......We derive an approximate analytical expression for the bit error rate of cascaded fiber links containing all-optical 2R-regenerators. A general analysis of the interplay between noise due to amplification and the degree of reshaping (nonlinearity) of the regenerator is performed....

  4. Adaptive Bit Rate Video Streaming Through an RF/Free Space Optical Laser Link

    Directory of Open Access Journals (Sweden)

    A. Akbulut

    2010-06-01

    Full Text Available This paper presents a channel-adaptive video streaming scheme which adjusts video bit rate according to channel conditions and transmits video through a hybrid RF/free space optical (FSO laser communication system. The design criteria of the FSO link for video transmission to 2.9 km distance have been given and adaptive bit rate video streaming according to the varying channel state over this link has been studied. It has been shown that the proposed structure is suitable for uninterrupted transmission of videos over the hybrid wireless network with reduced packet delays and losses even when the received power is decreased due to weather conditions.

  5. SITE project. Phase 1: Continuous data bit-error-rate testing

    Science.gov (United States)

    Fujikawa, Gene; Kerczewski, Robert J.

    1992-01-01

    The Systems Integration, Test, and Evaluation (SITE) Project at NASA LeRC encompasses a number of research and technology areas of satellite communications systems. Phase 1 of this project established a complete satellite link simulator system. The evaluation of proof-of-concept microwave devices, radiofrequency (RF) and bit-error-rate (BER) testing of hardware, testing of remote airlinks, and other tests were performed as part of this first testing phase. This final report covers the test results produced in phase 1 of the SITE Project. The data presented include 20-GHz high-power-amplifier testing, 30-GHz low-noise-receiver testing, amplitude equalization, transponder baseline testing, switch matrix tests, and continuous-wave and modulated interference tests. The report also presents the methods used to measure the RF and BER performance of the complete system. Correlations of the RF and BER data are summarized to note the effects of the RF responses on the BER.

  6. Low-bit rate speech encoders based on Line-Spectrum Frequencies (LSF)

    Science.gov (United States)

    Kang, G. S.; Fransen, L. J.

    1985-01-01

    After nearly a dozen years of research and development, the narrowband linear predictive coder (LPC) operating at 2400 bits per second (b/s) has become a practical means to transmit speech at less than 5% of the bit rate of the original digitized speech. The 2400-b/s LPC is expected to be deployed extensively on various military platforms. Recently, however, there has been a growing interest in very-low-data-rate (VLDR) (800 b/s or less) voice communication for certain specialized military communications. Likewise, there is a demand for a voice processor operating at 4800 b/s that outperforms significantly the current 2400-b/s LPC is for operation in less than favorable environments. We present in this report a means for implementing 800- and 4800-b/s voice processors. Both processors use a similar speech synthesis filter in which control parameters are line-spectrum frequencies (LSFs). The LSFs are frequency-domain parameters transformed directly from the prediction coefficients used in the conventional-narrowband LPC. The use of frequency-domain parameters is highly significant because they allow filter coefficient quantization in accordance with properties of auditory perception (i.e., coarser representation of higher frequency components of the speech spectrum). The excitation signal at the 800-b/s rate is similar to that used in the conventional-narrowband LPC. On the other hand, the excitation signal at 4800 b/s is the baseband residual signal. At 800 b/s, speech intelligibility as measured by the diagnostic rhyme test (DRT) is 87 for three male speakers; this is about 1.4 points lower than that of the 2400-b/s LPC.

  7. Performance Analysis for Bit Error Rate of DS- CDMA Sensor Network Systems with Source Coding

    Directory of Open Access Journals (Sweden)

    Haider M. AlSabbagh

    2012-03-01

    Full Text Available The minimum energy (ME coding combined with DS-CDMA wireless sensor network is analyzed in order to reduce energy consumed and multiple access interference (MAI with related to number of user(receiver. Also, the minimum energy coding which exploits redundant bits for saving power with utilizing RF link and On-Off-Keying modulation. The relations are presented and discussed for several levels of errors expected in the employed channel via amount of bit error rates and amount of the SNR for number of users (receivers.

  8. Power consumption analysis of constant bit rate data transmission over 3G mobile wireless networks

    DEFF Research Database (Denmark)

    Wang, Le; Ukhanova, Ann; Belyaev, Evgeny

    2011-01-01

    This paper presents the analysis of the power consumption of data transmission with constant bit rate over 3G mobile wireless networks. Our work includes the description of the transition state machine in 3G networks, followed by the detailed energy consumption analysis and measurement results...

  9. An Investigation on Advantages of Utilizing Adaptive Bit Rate for LEO Satellite Link Engineering

    Directory of Open Access Journals (Sweden)

    Mehdi Hosseini

    2012-09-01

    Full Text Available The paper aims to investigate the advantages of using adaptive bit rate in the communication link of a LEO satellite. While doing the study, it is assumed that there is a communication subsystem on-board responsible for gathering the information sent by a number of ground user terminals. The subsystem which operates based on Store-and-Forward (SAF Scenario, contains two communication links, one for receiving data from user terminals (store case, and the other for forwarding the stored data to an Earth station (forward case. In fact, the current work aims to improve the volume of the data forwarded to Earth station. To this end, the Forward case bit rate is varied adaptively, and then by analyzing the power budget in a practical condition, the improvement achieved is evaluated. The results specifically obtained for a sample LEO satellite shows that utilizing adaptive bit rate instead of fixed bit rate can increase the daily data exchange up to about 100%.

  10. Analytical expression for the bit error rate of cascaded all-optical regenerators

    DEFF Research Database (Denmark)

    Mørk, Jesper; Öhman, Filip; Bischoff, S.

    2003-01-01

    We derive an approximate analytical expression for the bit error rate of cascaded fiber links containing all-optical 2R-regenerators. A general analysis of the interplay between noise due to amplification and the degree of reshaping (nonlinearity) of the regenerator is performed....

  11. Achievable Rates for Four-Dimensional Coded Modulation with a Bit-Wise Receiver

    CERN Document Server

    Alvarado, Alex

    2013-01-01

    We study achievable rates for four-dimensional (4D) constellations for spectrally efficient optical systems based on a (suboptimal) bit-wise receiver. We show that PM-QPSK outperforms the best 4D constellation designed for uncoded transmission by approximately 1 dB. Numerical results using LDPC codes validate the analysis.

  12. Rate Request Sequenced Bit Loading Secondary User Reallocation Algorithm for DMT Systems in Cognitive Radio

    Directory of Open Access Journals (Sweden)

    S. Chris Prema

    2015-01-01

    Full Text Available A rate request sequenced bit loading reallocation algorithm is proposed. The spectral holes detected by spectrum sensing (SS in cognitive radio (CR are used by secondary users. This algorithm is applicable to Discrete Multitone (DMT systems for secondary user reallocation. DMT systems support different modulation on different subchannels according to Signal-to-Noise Ratio (SNR. The maximum bits and power that can be allocated to each subband is determined depending on the channel state information (CSI and secondary user modulation scheme. The spectral holes or free subbands are allocated to secondary users depending on the user rate request and subchannel capacity. A comparison is done between random rate request and sequenced rate request of secondary user for subchannel allocation. Through simulations it is observed that with sequenced rate request higher spectral efficiency is achieved with reduced complexity.

  13. Design of High Speed 128 bit Parallel Prefix Adders

    OpenAIRE

    T.KIRAN KUMAR; Srikanth, P

    2014-01-01

    In this paper, we propose 128-bit Kogge-Stone, Ladner-Fischer, Spanning tree parallel prefix adders and compared with Ripple carry adder. In general N-bit adders like Ripple Carry Adders (slow adders compare to other adders), and Carry Look Ahead adders (area consuming adders) are used in earlier days. But now the most Industries are using parallel prefix adders because of their advantages compare to other adders. Parallel prefix adders are faster and area efficient. Parallel pref...

  14. Automatic network-adaptive ultra-low-bit-rate video coding

    Science.gov (United States)

    Chien, Wei-Jung; Lam, Tuyet-Trang; Abousleman, Glen P.; Karam, Lina J.

    2006-05-01

    This paper presents a software-only, real-time video coder/decoder (codec) for use with low-bandwidth channels where the bandwidth is unknown or varies with time. The codec incorporates a modified JPEG2000 core and interframe predictive coding, and can operate with network bandwidths of less than 1 kbits/second. The encoder and decoder establish two virtual connections over a single IP-based communications link. The first connection is UDP/IP guaranteed throughput, which is used to transmit the compressed video stream in real time, while the second is TCP/IP guaranteed delivery, which is used for two-way control and compression parameter updating. The TCP/IP link serves as a virtual feedback channel and enables the decoder to instruct the encoder to throttle back the transmission bit rate in response to the measured packet loss ratio. It also enables either side to initiate on-the-fly parameter updates such as bit rate, frame rate, frame size, and correlation parameter, among others. The codec also incorporates frame-rate throttling whereby the number of frames decoded is adjusted based upon the available processing resources. Thus, the proposed codec is capable of automatically adjusting the transmission bit rate and decoding frame rate to adapt to any network scenario. Video coding results for a variety of network bandwidths and configurations are presented to illustrate the vast capabilities of the proposed video coding system.

  15. Giga bit per second Differential Scheme for High Speed Interconnect

    Directory of Open Access Journals (Sweden)

    Mandeep Singh Narula

    2012-02-01

    Full Text Available The performance of many digital systems today is limited by the interconnection bandwidth between chips. Although the processing performance of a single chip has increased dramatically since the inception of the integrated circuit technology, the communication bandwidth between chips has not enjoyed as much benefit. Most CMOS chips, when communicating off-chip, drive un terminated lines with full-swing CMOS drivers. Such full-swing CMOS interconnect ring-up the line, and hence has a bandwidth that is limited by the length of the line rather than the performance of the semiconductor technology. Thus, as VLSI technology scales, the pin bandwidth does not improve with the technology, but rather remains limited by board and cable geometry, making off-chip bandwidth an even more critical bottleneck. In order to increase the I/O Bandwidth, some efficient high speed signaling standard must be used which considers the line termination, signal integrity, power dissipation, noise immunity etc In this work, a transmitter has been developed for high speed off chip communication. It consists of low speed input buffer, serializer which converts parallel input data into serial data and a current mode driver which converts the voltage mode input signals into current over the transmission line. Output of 32 low speed input buffers is fed to two serializer, each serializer converting 16 bit parallel data into serial data stream. Output of two serializers is fed to LVDS current mode driver. The serial link technique used in this work is the time division multiplex (TDM and point-to-point technique. It means that the low-speed parallel signals are transferred to the high-speed serial signal at the transmitter end and the high-speed serial signal is transferred to the low-speed parallel signals at the receiver end. Serial link is the design of choice in any application where the cost of the communication channel is high and duplicating the links in large numbers is

  16. Giga bit per second Differential Scheme for High Speed Interconnect

    Directory of Open Access Journals (Sweden)

    Mandeep Singh Narula

    2012-03-01

    Full Text Available The performance of many digital systems today is limited by the interconnection bandwidth between chips. Although the processing performance of a single chip has increased dramatically since the inception of the integrated circuit technology, the communication bandwidth between chips has not enjoyed as much benefit. Most CMOS chips, when communicating off-chip, drive unterminated lines with full-swing CMOS drivers. Such full-swing CMOS interconnect ring-up the line, and hence has a bandwidth that is limited by the length of the line rather than the performance of the semiconductor technology. Thus, as VLSI technology scales, the pin bandwidth does not improve with the technology, but rather remains limited by board and cable geometry, making off-chip bandwidth an even more critical bottleneck. In order to increase the I/O Bandwidth, some efficient high speed signaling standard must be used which considers the line termination, signal integrity, power dissipation, noise immunity etc In this work, a transmitter has been developed for high speed offchip communication. It consists of low speed input buffer, serializer which converts parallel input data into serial data and a current mode driver which converts the voltage mode input signals into current over the transmission line. Output of 32 low speed input buffers is fed to two serializer, each serializer converting 16 bit parallel data into serial data stream. Output of two serializers is fed to LVDS current mode driver. The serial link technique used in this work is the time division multiplex (TDM and point-to-point technique. It means that the low-speed parallel signals are transferred to the high-speed serial signal at the transmitter end and the high-speed serial signal is transferred to the low-speed parallel signals at the receiver end. Serial link is the design of choice in any application where the cost of the communication channel is high and duplicating the links in large numbers is

  17. High performance word level sequential and parallel coding methods and architectures for bit plane coding

    Institute of Scientific and Technical Information of China (English)

    XIONG ChengYi; TIAN JinWen; LIU Jian

    2008-01-01

    This paper introduced a novel high performance algorithm and VLSI architectures for achieving bit plane coding (BPC) in word level sequential and parallel mode. The proposed BPC algorithm adopts the techniques of coding pass prediction and par-allel & pipeline to reduce the number of accessing memory and to increase the ability of concurrently processing of the system, where all the coefficient bits of a code block could be coded by only one scan. A new parallel bit plane architecture (PA) was proposed to achieve word-level sequential coding. Moreover, an efficient high-speed architecture (HA) was presented to achieve multi-word parallel coding. Compared to the state of the art, the proposed PA could reduce the hardware cost more efficiently, though the throughput retains one coefficient coded per clock. While the proposed HA could perform coding for 4 coefficients belonging to a stripe column at one intra-clock cycle, so that coding for an N×N code-block could be completed in approximate N2/4 intra-clock cycles. Theoretical analysis and ex-perimental results demonstrate that the proposed designs have high throughput rate with good performance in terms of speedup to cost, which can be good alter-natives for low power applications.

  18. A Very Efficient Transfer Function Bounding Technique on Bit Error Rate for Viterbi Decoded, Rate 1/N Convolutional Codes

    Science.gov (United States)

    Lee, P. J.

    1984-01-01

    For rate 1/N convolutional codes, a recursive algorithm for finding the transfer function bound on bit error rate (BER) at the output of a Viterbi decoder is described. This technique is very fast and requires very little storage since all the unnecessary operations are eliminated. Using this technique, we find and plot bounds on the BER performance of known codes of rate 1/2 with K 18, rate 1/3 with K 14. When more than one reported code with the same parameter is known, we select the code that minimizes the required signal to noise ratio for a desired bit error rate of 0.000001. This criterion of determining goodness of a code had previously been found to be more useful than the maximum free distance criterion and was used in the code search procedures of very short constraint length codes. This very efficient technique can also be used for searches of longer constraint length codes.

  19. Bit Error Rate Performance of a MIMO-CDMA System Employing Parity-Bit-Selected Spreading in Frequency Nonselective Rayleigh Fading

    Directory of Open Access Journals (Sweden)

    Claude D'Amours

    2011-01-01

    Full Text Available We analytically derive the upper bound for the bit error rate (BER performance of a single user multiple input multiple output code division multiple access (MIMO-CDMA system employing parity-bit-selected spreading in slowly varying, flat Rayleigh fading. The analysis is done for spatially uncorrelated links. The analysis presented demonstrates that parity-bit-selected spreading provides an asymptotic gain of 10log(Nt dB over conventional MIMO-CDMA when the receiver has perfect channel estimates. This analytical result concurs with previous works where the (BER is determined by simulation methods and provides insight into why the different techniques provide improvement over conventional MIMO-CDMA systems.

  20. 3D video bit rate adaptation decision taking using ambient illumination context

    Directory of Open Access Journals (Sweden)

    G. Nur Yilmaz

    2014-09-01

    Full Text Available 3-Dimensional (3D video adaptation decision taking is an open field in which not many researchers have carried out investigations yet compared to 3D video display, coding, etc. Moreover, utilizing ambient illumination as an environmental context for 3D video adaptation decision taking has particularly not been studied in literature to date. In this paper, a user perception model, which is based on determining perception characteristics of a user for a 3D video content viewed under a particular ambient illumination condition, is proposed. Using the proposed model, a 3D video bit rate adaptation decision taking technique is developed to determine the adapted bit rate for the 3D video content to maintain 3D video quality perception by considering the ambient illumination condition changes. Experimental results demonstrate that the proposed technique is capable of exploiting the changes in ambient illumination level to use network resources more efficiently without sacrificing the 3D video quality perception.

  1. Novel relations between the ergodic capacity and the average bit error rate

    KAUST Repository

    Yilmaz, Ferkan

    2011-11-01

    Ergodic capacity and average bit error rate have been widely used to compare the performance of different wireless communication systems. As such recent scientific research and studies revealed strong impact of designing and implementing wireless technologies based on these two performance indicators. However and to the best of our knowledge, the direct links between these two performance indicators have not been explicitly proposed in the literature so far. In this paper, we propose novel relations between the ergodic capacity and the average bit error rate of an overall communication system using binary modulation schemes for signaling with a limited bandwidth and operating over generalized fading channels. More specifically, we show that these two performance measures can be represented in terms of each other, without the need to know the exact end-to-end statistical characterization of the communication channel. We validate the correctness and accuracy of our newly proposed relations and illustrated their usefulness by considering some classical examples. © 2011 IEEE.

  2. Threshold based Bit Error Rate Optimization in Four Wave Mixing Optical WDM Systems

    Directory of Open Access Journals (Sweden)

    Er. Karamjeet Kaur

    2016-07-01

    Full Text Available Optical communication is communication at a distance using light to carry information which can be performed visually or by using electronic devices. The trend toward higher bit rates in light-wave communication has interest in dispersion-shifted fibre to reduce dispersion penalties. At an equivalent time optical amplifiers have exaggerated interest in wavelength multiplexing. This paper describes optical communication systems where we discuss different optical multiplexing schemes. The effect of channel power depletion due to generation of Four Wave Mixing waves and the effect of FWM cross talk on the performance of a WDM receiver has been studied in this paper. The main focus is to minimize Bit Error Rate to increase the QoS of the optical WDM system.

  3. Performance of the JPEG Estimated Spectrum Adaptive Postfilter (JPEG-ESAP) for Low Bit Rates

    Science.gov (United States)

    Linares, Irving (Inventor)

    2016-01-01

    Frequency-based, pixel-adaptive filtering using the JPEG-ESAP algorithm for low bit rate JPEG formatted color images may allow for more compressed images while maintaining equivalent quality at a smaller file size or bitrate. For RGB, an image is decomposed into three color bands--red, green, and blue. The JPEG-ESAP algorithm is then applied to each band (e.g., once for red, once for green, and once for blue) and the output of each application of the algorithm is rebuilt as a single color image. The ESAP algorithm may be repeatedly applied to MPEG-2 video frames to reduce their bit rate by a factor of 2 or 3, while maintaining equivalent video quality, both perceptually, and objectively, as recorded in the computed PSNR values.

  4. Novel Relations between the Ergodic Capacity and the Average Bit Error Rate

    CERN Document Server

    Yilmaz, Ferkan

    2012-01-01

    Ergodic capacity and average bit error rate have been widely used to compare the performance of different wireless communication systems. As such recent scientific research and studies revealed strong impact of designing and implementing wireless technologies based on these two performance indicators. However and to the best of our knowledge, the direct links between these two performance indicators have not been explicitly proposed in the literature so far. In this paper, we propose novel relations between the ergodic capacity and the average bit error rate of an overall communication system using binary modulation schemes for signaling with a limited bandwidth and operating over generalized fading channels. More specifically, we show that these two performance measures can be represented in terms of each other, without the need to know the exact end-to-end statistical characterization of the communication channel. We validate the correctness and accuracy of our newly proposed relations and illustrated their...

  5. Very Low Bit-Rate Video Coding Using Motion ompensated 3-D Wavelet Transform

    Institute of Scientific and Technical Information of China (English)

    1999-01-01

    A new motion-compensated 3-D wavelet transform (MC-3DWT) video coding scheme is presented in thispaper. The new coding scheme has a good performance in average PSNR, compression ratio and visual quality of re-constructions compared with the existing 3-D wavelet transform (3DWT) coding methods and motion-compensated2-D wavelet transform (MC-WT) coding method. The new MC-3DWT coding scheme is suitable for very low bit-rate video coding.

  6. Asymptotic correctability of Bell-diagonal quantum states and maximum tolerable bit error rates

    CERN Document Server

    Ranade, K S; Ranade, Kedar S.; Alber, Gernot

    2005-01-01

    The general conditions are discussed which quantum state purification protocols have to fulfill in order to be capable of purifying Bell-diagonal qubit-pair states, provided they consist of steps that map Bell-diagonal states to Bell-diagonal states and they finally apply a suitably chosen Calderbank-Shor-Steane code to the outcome of such steps. As a main result a necessary and a sufficient condition on asymptotic correctability are presented, which relate this problem to the magnitude of a characteristic exponent governing the relation between bit and phase errors under the purification steps. These conditions allow a straightforward determination of maximum tolerable bit error rates of quantum key distribution protocols whose security analysis can be reduced to the purification of Bell-diagonal states.

  7. Bit-error-rate testing of fiber optic data links for MMIC-based phased array antennas

    Science.gov (United States)

    Shalkhauser, K. A.; Kunath, R. R.; Daryoush, A. S.

    1990-01-01

    The measured bit-error-rate (BER) performance of a fiber optic data link to be used in satellite communications systems is presented and discussed. In the testing, the link was measured for its ability to carry high burst rate, serial-minimum shift keyed (SMSK) digital data similar to those used in actual space communications systems. The fiber optic data link, as part of a dual-segment injection-locked RF fiber optic link system, offers a means to distribute these signals to the many radiating elements of a phased array antenna. Test procedures, experimental arrangements, and test results are presented.

  8. An Industry/DOE Program to Develop and Benchmark Advanced Diamond Product Drill Bits and HP/HT Drilling Fluids to Significantly Improve Rates of Penetration

    Energy Technology Data Exchange (ETDEWEB)

    TerraTek

    2007-06-30

    A deep drilling research program titled 'An Industry/DOE Program to Develop and Benchmark Advanced Diamond Product Drill Bits and HP/HT Drilling Fluids to Significantly Improve Rates of Penetration' was conducted at TerraTek's Drilling and Completions Laboratory. Drilling tests were run to simulate deep drilling by using high bore pressures and high confining and overburden stresses. The purpose of this testing was to gain insight into practices that would improve rates of penetration and mechanical specific energy while drilling under high pressure conditions. Thirty-seven test series were run utilizing a variety of drilling parameters which allowed analysis of the performance of drill bits and drilling fluids. Five different drill bit types or styles were tested: four-bladed polycrystalline diamond compact (PDC), 7-bladed PDC in regular and long profile, roller-cone, and impregnated. There were three different rock types used to simulate deep formations: Mancos shale, Carthage marble, and Crab Orchard sandstone. The testing also analyzed various drilling fluids and the extent to which they improved drilling. The PDC drill bits provided the best performance overall. The impregnated and tungsten carbide insert roller-cone drill bits performed poorly under the conditions chosen. The cesium formate drilling fluid outperformed all other drilling muds when drilling in the Carthage marble and Mancos shale with PDC drill bits. The oil base drilling fluid with manganese tetroxide weighting material provided the best performance when drilling the Crab Orchard sandstone.

  9. High power laser-mechanical drilling bit and methods of use

    Energy Technology Data Exchange (ETDEWEB)

    Grubb, Daryl L.; Kolachalam, Sharath K.; Faircloth, Brian O.; Rinzler, Charles C.; Allen, Erik C.; Underwood, Lance D.; Zediker, Mark S.

    2017-02-07

    An apparatus with a high power laser-mechanical bit for use with a laser drilling system and a method for advancing a borehole. The laser-mechanical bit has a beam path and mechanical removal devices that provide for the removal of laser-affected rock to advance a borehole.

  10. All-optical wavelength conversion at bit rates above 10 Gb/s using semiconductor optical amplifiers

    DEFF Research Database (Denmark)

    Jørgensen, Carsten; Danielsen, Søren Lykke; Stubkjær, Kristian

    1997-01-01

    This work assesses the prospects for high-speed all-optical wavelength conversion using the simple optical interaction with the gain in semiconductor optical amplifiers (SOAs) via the interband carrier recombination. Operation and design guidelines for conversion speeds above 10 Gb/s are described...... and the various tradeoffs are discussed. Experiments at bit rates up to 40 Gb/s are presented for both cross-gain modulation (XGM) and cross-phase modulation (XPM) in SOAs demonstrating the high-speed capability of these techniques...

  11. Alpha coding of arbitrarily shaped objects for low-bit-rate MPEG-4

    Science.gov (United States)

    Hadar, Ofer; Folkman, Hagai

    2001-11-01

    This paper presents a new scheme for compact shape-coding which can reduce the needed bandwidth for low bit rate MPEG- 4 applications. Our scheme is based on a coarse representation of the alpha plane with a block size resolution of 8x8 pixels. This arrangement saves bandwidth and reduces the algorithm complexity (number of computations), as compared to the Content-based Arithmetic Encoding (CAE) algorithm. In our algorithm, we encode the alpha plane of a macroblock with only 4 bits, while we can further reduce the number of encoding bits by using the Huffman code. The encoding blocks are only contour macroblocks, transparent macroblocks are considered as background macroblocks, while opaque macroblocks are considered as object macroblocks. We show that the amount of bandwidth saving with representing the alpha-plane can reach a factor of 9.5. Such a scheme is appropriate for mobile applications where there is a lack of both bandwidth and processing power. We also speculate that our scheme will be compatible to the MPEG-4 standard.

  12. An 18-bit high performance audio {sigma}-{Delta} D/A converter

    Energy Technology Data Exchange (ETDEWEB)

    Zhang Hao; Han Yan; Han Xiaoxia; Wang Hao; Liang Guo [Institute of Microelectronics and Photoelectronics, Zhejiang University, Hangzhou 310027 (China); Huang Xiaowei [CISD, Institute of Microelectronic CAD, Hangzhou 310018 (China); Cheung, Ray C., E-mail: huangxw@hdu.edu.c [Department of Electronic Engineering, City University of Hong Kong (Hong Kong)

    2010-07-15

    A multi-bit quantized high performance sigma-delta ({sigma}-{Delta}) audio DAC is presented. Compared to its single-bit counterpart, the multi-bit quantization offers many advantages, such as simpler {sigma}-{Delta} modulator circuit, lower clock frequency and smaller spurious tones. With the data weighted average (DWA) mismatch shaping algorithm, element mismatch errors induced by multi-bit quantization can be pushed out of the signal band, hence the noise floor inside the signal band is greatly lowered. To cope with the crosstalk between digital and analog circuits, every analog component is surrounded by a guard ring, which is an innovative attempt. The 18-bit DAC with the above techniques, which is implemented in a 0.18 {mu}m mixed-signal CMOS process, occupies a core area of 1.86 mm{sup 2}. The measured dynamic range (DR) and peak SNDR are 96 dB and 88 dB, respectively.

  13. An 18-bit high performance audio σ-Δ D/A converter

    Science.gov (United States)

    Hao, Zhang; Xiaowei, Huang; Yan, Han; Cheung, Ray C.; Xiaoxia, Han; Hao, Wang; Guo, Liang

    2010-07-01

    A multi-bit quantized high performance sigma-delta (σ-Δ) audio DAC is presented. Compared to its single-bit counterpart, the multi-bit quantization offers many advantages, such as simpler σ-Δ modulator circuit, lower clock frequency and smaller spurious tones. With the data weighted average (DWA) mismatch shaping algorithm, element mismatch errors induced by multi-bit quantization can be pushed out of the signal band, hence the noise floor inside the signal band is greatly lowered. To cope with the crosstalk between digital and analog circuits, every analog component is surrounded by a guard ring, which is an innovative attempt. The 18-bit DAC with the above techniques, which is implemented in a 0.18 μm mixed-signal CMOS process, occupies a core area of 1.86 mm2. The measured dynamic range (DR) and peak SNDR are 96 dB and 88 dB, respectively.

  14. A minimum bit error-rate detector for amplify and forward relaying systems

    KAUST Repository

    Ahmed, Qasim Zeeshan

    2012-05-01

    In this paper, a new detector is being proposed for amplify-and-forward (AF) relaying system when communicating with the assistance of L number of relays. The major goal of this detector is to improve the bit error rate (BER) performance of the system. The complexity of the system is further reduced by implementing this detector adaptively. The proposed detector is free from channel estimation. Our results demonstrate that the proposed detector is capable of achieving a gain of more than 1-dB at a BER of 10 -5 as compared to the conventional minimum mean square error detector when communicating over a correlated Rayleigh fading channel. © 2012 IEEE.

  15. Power consumption analysis of constant bit rate video transmission over 3G networks

    DEFF Research Database (Denmark)

    Ukhanova, Ann; Belyaev, Evgeny; Wang, Le

    2012-01-01

    for the 3GPP transition state machine that allows to decrease power consumption on a mobile device taking signaling traffic, buffer size and latency restrictions into account. Furthermore, we discuss the gain in power consumption vs. PSNR for transmitted video and show the possibility of performing power......This paper presents an analysis of the power consumption of video data transmission with constant bit rate over 3G mobile wireless networks. The work includes the description of the radio resource control transition state machine in 3G networks, followed by a detailed power consumption analysis...... consumption management based on the requirements for the video quality....

  16. Linear transceiver design for nonorthogonal amplify-and-forward protocol using a bit error rate criterion

    KAUST Repository

    Ahmed, Qasim Zeeshan

    2014-04-01

    The ever growing demand of higher data rates can now be addressed by exploiting cooperative diversity. This form of diversity has become a fundamental technique for achieving spatial diversity by exploiting the presence of idle users in the network. This has led to new challenges in terms of designing new protocols and detectors for cooperative communications. Among various amplify-and-forward (AF) protocols, the half duplex non-orthogonal amplify-and-forward (NAF) protocol is superior to other AF schemes in terms of error performance and capacity. However, this superiority is achieved at the cost of higher receiver complexity. Furthermore, in order to exploit the full diversity of the system an optimal precoder is required. In this paper, an optimal joint linear transceiver is proposed for the NAF protocol. This transceiver operates on the principles of minimum bit error rate (BER), and is referred as joint bit error rate (JBER) detector. The BER performance of JBER detector is superior to all the proposed linear detectors such as channel inversion, the maximal ratio combining, the biased maximum likelihood detectors, and the minimum mean square error. The proposed transceiver also outperforms previous precoders designed for the NAF protocol. © 2002-2012 IEEE.

  17. An Improved Rate Matching Method for DVB Systems Through Pilot Bit Insertion

    Directory of Open Access Journals (Sweden)

    Seyed Mohammad-Sajad Sadough

    2012-09-01

    Full Text Available Classically, obtaining different coding rates in turbo codes is achieved through the well known puncturing procedure. However, puncturing is a critical procedure since the way the encoded sequence is punctured influences directly the decoding performance. In this work, we propose to mix the data sequence at the turbo encoder input inside the Digital Video Broadcasting (DVB standard with some pilot (perfectly known bits. By using variable pilot insertion rates, we achieve different coding rates with more flexibility. The proposed scheme is able to use a less complex mother code compared to that used in a conventional punctured turbo code. We also analyze the effect of different type of pilot insertion such as random and periodic schemes. Simulation results provided in the context of DVB show that in addition to providing flexible encoder design and reducing the encoder complexity, pilot insertion can improve slightly the performance of turbo decoders, compared to a conventional punctured turbo code.

  18. Bit Rate Maximising Per-Tone Equalisation with Adaptive Implementation for DMT-Based Systems

    Directory of Open Access Journals (Sweden)

    Suchada Sitjongsataporn

    2009-01-01

    Full Text Available We present a bit rate maximising per-tone equalisation (BM-PTEQ cost function that is based on an exact subchannel SNR as a function of per-tone equaliser in discrete multitone (DMT systems. We then introduce the proposed BM-PTEQ criterion whose derivation for solution is shown to inherit from the methodology of the existing bit rate maximising time-domain equalisation (BM-TEQ. By solving a nonlinear BM-PTEQ cost function, an adaptive BM-PTEQ approach based on a recursive Levenberg-Marquardt (RLM algorithm is presented with the adaptive inverse square-root (iQR algorithm for DMT-based systems. Simulation results confirm that the performance of the proposed adaptive iQR RLM-based BM-PTEQ converges close to the performance of the proposed BM-PTEQ. Moreover, the performance of both these proposed BM-PTEQ algorithms is improved as compared with the BM-TEQ.

  19. Bit Rate Reduction of FS-1015 Speech Coder Using Fuzzy ARTMAP and KSOFM Neural Networks

    Directory of Open Access Journals (Sweden)

    Ali Eslamzadeh

    2009-03-01

    Full Text Available The speech spectrum is very sensitive to linear predictive coding (LPC parameters, so small quantization errors may cause unstable synthesis filter. Line spectral pairs (LSPs are more efficient representations than LPC parameters. On the other hand, artificial neural networks (ANNs have been used successfully to improving the quality and also reduction the computational complexity of speech coders. This work proposes an efficient technique to reduce the bit rate of FS-1015 speech coder, while improving the performance. In this way, LSP parameters are used instead of the LPC parameters. In addition, neural vector quantizers based on Kohonen self-organizing feature map (KSOFM, with a modified-supervised training algorithm, and fuzzy ARTMAP are also employed to reduce the bit rate. By using the mentioned neural vector quantizer models, the quality of synthesized speech, in terms of mean opinion score (MOS, is improved 0.13 and 0.26, respectively. The execution time of proposed models, as compared to FS-1015 standard, is also reduced 27% and 43%, respectively.

  20. Speech Compression of Thai Dialects with Low-Bit-Rate Speech Coders

    Directory of Open Access Journals (Sweden)

    Suphattharachai Chomphan

    2012-01-01

    Full Text Available Problem statement: In modern speech communication at low bit rate, speech coding deteriorates the characteristics of the coded speech significantly. Considering the dialects in Thai, the coding quality of four main dialects spoken by Thai people residing in four core region including central, north, northeast and south regions has not been studied. Approach: This study presents a comparative study of the coding quality of four main Thai dialects by using different low-bit-rate speech coders including the Conjugate Structure Algebraic Code Excited Linear Predictive (CS-ACELP coder and the Multi-Pulse based Code Excited Linear Predictive (MP-CELP coder. The objective and subjective tests have been conducted to evaluate the coding quality of four main dialects. Results: From the experimental results, both tests show that the coding quality of North dialect is highest, meanwhile the coding quality of Northeast dialect is lowest. Moreover, the coding quality of male speech is mostly higher than that of female speech. Conclusion: From the study, it can be obviously seen that the coding quality of all Thai dialects are different.

  1. Quantum dot semiconductor optical amplifier: role of second excited state on ultrahigh bit-rate signal processing.

    Science.gov (United States)

    Izadyar, Seyed Mohsen; Razaghi, Mohammad; Hassanzadeh, Abdollah

    2017-04-20

    In this paper, a theoretical model for a quantum dot semiconductor optical amplifier (QDSOA) is proposed. The dynamics of carriers in ground, excited, and continuum states and wetting layer are considered in this model. The effects of the second excited state (ES2) inclusion are investigated for the first time, to the best of our knowledge, in the proposed QDSOA model. Moreover, the inhomogeneous broadening effect due to size distribution of dots, and the homogeneous broadening effect of a single dot in the gain spectrum by grouping of dots based on their optical resonant frequency, are included in the model. Furthermore, grouping of photon modes is considered in the model. It is shown that improvement of QDSOA performance is possible by considering ES2 in rate equations. Gain saturation in different injection currents is obtained for various square-shaped pulse train bit-rates. It is shown that carriers' relaxation time plays an important role in signal amplification and processing of QDSOA. The results illustrate that QDSOA can be used for high bit-rate signal processing devices (up to 450 Gbps) with negligible wave distortion and fast gain recovery.

  2. Bit Error Rate Measurements on Prototype Digital Optical Links for the CMS Tracker

    CERN Document Server

    Azevedo, C S; Faccio, F; Gill, Karl; Grabit, Robert; Jensen, Fredrik Bjorn Henning; Vasey, François

    2000-01-01

    Two prototypes of a four-channel digital optical link to be used for the slow control of the CMS Tracker detector were tested for bit error rate, at transmission rates of 40 Mbit/s and 80 Mbit/s. Both prototypes used the same transmitter and PIN photodiode, but different receiver configurations: one used COTS electronics, whilst the other used a digital receiver ASIC developed at CERN in a 0.25 mm process. Both links proved to be well within the specification limits even after the ASIC receiver was irradiated to a 20 Mrad total dose, and the PIN photodiode to a 6.5á1014 n/cm2 fluence.

  3. Advanced High-Speed 16-Bit Digitizer System

    Energy Technology Data Exchange (ETDEWEB)

    None

    2012-05-01

    The fastest commercially available 16-bit ADC can only perform around 200 mega-samples per second (200 MS/s). Connecting ADC chips together in eight different time domains increases the quantity of samples taken by a factor of eight. This method of interleaving requires that the input signal being sampled is split into eight identical signals and arrives at each ADC chip at the same point in time. The splitting of the input signal is performed in the analog front end containing a wideband filter that impedance matches the input signal to the ADC chips. Each ADC uses a clock to tell it when to perform a conversion. Using eight unique clocks spaced in 45-degree increments is the method used to time shift when each ADC chip performs its conversion. Given that this control clock is a fixed frequency, the clock phase shifting is accomplished by tightly controlling the distance that the clock must travel, resulting in a time delay. The interleaved ADC chips will now generate digital data in eight different time domains. These data are processed inside a field-programmable gate array (FPGA) to move the data back into a single time domain and store it into memory. The FPGA also contains a Nios II processor that provides system control and data retrieval via Ethernet.

  4. KAPASITAS KANAL DAN BIT ERROR RATE SISTEM D-MIMO DALAM VARIASI SPASIAL DAERAH CAKUPAN

    Directory of Open Access Journals (Sweden)

    Nyoman Gunantara

    2009-05-01

    Full Text Available Kemajuan teknologi komunikasi, dikembangkan sistem D-MIMO (Distributed MIMO yang sebelumnya telah digunakan sistem C-MIMO (Conventional co-located MIMO. Sistem C-MIMO menyebabkan penggunaan spektrummenjadi efisien, daya pancar berkurang, dan kapasitas kanal meningkat.Dengan sistem D-MIMO jarak antara pemancar dan penerima dapat diperpendek, macrodiversity dan adanya daerah cakupan layanan. Pada tulisan ini akan diteliti tentang kapasitas kanal dan Bit Error Rate (BER pada variasi spasial daerah cakupan. Penelitian tersebut dilakukan pada kapasitas kanal teoritis dan BER dengan teknik waterfilling.Kapasitas kanal dan kinerja BER pada sistem D-MIMO pada variasi spasial daerah cakupan tergantung dari konfigurasi sistem D-MIMO. Lokasi penerima yang dekat port antena pemancar mempunyai kapasitas kanal yanglebih besar tetapi memiliki kinerja BER yang lebih buruk.

  5. Bit Error Rate Analysis for MC-CDMA Systems in Nakagami- Fading Channels

    Directory of Open Access Journals (Sweden)

    Li Zexian

    2004-01-01

    Full Text Available Multicarrier code division multiple access (MC-CDMA is a promising technique that combines orthogonal frequency division multiplexing (OFDM with CDMA. In this paper, based on an alternative expression for the -function, characteristic function and Gaussian approximation, we present a new practical technique for determining the bit error rate (BER of multiuser MC-CDMA systems in frequency-selective Nakagami- fading channels. The results are applicable to systems employing coherent demodulation with maximal ratio combining (MRC or equal gain combining (EGC. The analysis assumes that different subcarriers experience independent fading channels, which are not necessarily identically distributed. The final average BER is expressed in the form of a single finite range integral and an integrand composed of tabulated functions which can be easily computed numerically. The accuracy of the proposed approach is demonstrated with computer simulations.

  6. Optimization of Deep Drilling Performance--Development and Benchmark Testing of Advanced Diamond Product Drill Bits & HP/HT Fluids to Significantly Improve Rates of Penetration

    Energy Technology Data Exchange (ETDEWEB)

    Alan Black; Arnis Judzis

    2003-10-01

    This document details the progress to date on the OPTIMIZATION OF DEEP DRILLING PERFORMANCE--DEVELOPMENT AND BENCHMARK TESTING OF ADVANCED DIAMOND PRODUCT DRILL BITS AND HP/HT FLUIDS TO SIGNIFICANTLY IMPROVE RATES OF PENETRATION contract for the year starting October 2002 through September 2002. The industry cost shared program aims to benchmark drilling rates of penetration in selected simulated deep formations and to significantly improve ROP through a team development of aggressive diamond product drill bit--fluid system technologies. Overall the objectives are as follows: Phase 1--Benchmark ''best in class'' diamond and other product drilling bits and fluids and develop concepts for a next level of deep drilling performance; Phase 2--Develop advanced smart bit--fluid prototypes and test at large scale; and Phase 3--Field trial smart bit--fluid concepts, modify as necessary and commercialize products. Accomplishments to date include the following: 4Q 2002--Project started; Industry Team was assembled; Kick-off meeting was held at DOE Morgantown; 1Q 2003--Engineering meeting was held at Hughes Christensen, The Woodlands Texas to prepare preliminary plans for development and testing and review equipment needs; Operators started sending information regarding their needs for deep drilling challenges and priorities for large-scale testing experimental matrix; Aramco joined the Industry Team as DEA 148 objectives paralleled the DOE project; 2Q 2003--Engineering and planning for high pressure drilling at TerraTek commenced; 3Q 2003--Continuation of engineering and design work for high pressure drilling at TerraTek; Baker Hughes INTEQ drilling Fluids and Hughes Christensen commence planning for Phase 1 testing--recommendations for bits and fluids.

  7. Investigation on the bit error rate performance of 40Gb/s space optical communication system based on BPSK scheme

    Science.gov (United States)

    Li, Mi; Li, Bowen; Zhang, Xuping; Song, Yuejiang; Liu, Jia; Tu, Guojie

    2015-08-01

    Space optical communication technique is attracting increasingly more attention because it owns advantages such as high security and great communication quality compared with microwave communication. As the space optical communication develops, people have already achieved the communication at data rate of Gb/s currently. The next generation for space optical system have goal of the higher data rate of 40Gb/s. However, the traditional optical communication system cannot satisfy it when the data rate of system is at such high extent. This paper will introduce ground optical communication system of 40Gb/s data rate as to achieve the space optical communication at high data rate. Speaking of the data rate of 40Gb/s, we must apply waveguide modulator to modulate the optical signal and magnify this signal by laser amplifier. Moreover, the more sensitive avalanche photodiode (APD) will be as the detector to increase the communication quality. Based on communication system above, we analyze character of communication quality in downlink of space optical communication system when data rate is at the level of 40Gb/s. The bit error rate (BER) performance, an important factor to justify communication quality, versus some parameter ratios is discussed. From results, there exists optimum ratio of gain factor and divergence angle, which shows the best BER performance. We can also increase ratio of receiving diameter and divergence angle for better communication quality. These results can be helpful to comprehend the character of optical communication system at high data rate and contribute to the system design.

  8. A very low bit rate video coder based on vector quantization.

    Science.gov (United States)

    Corte-Real, L; Alves, A P

    1996-01-01

    Describes a video coder based on a hybrid DPCM-vector quantization algorithm that is suited for bit rates ranging from 8-16 kb/s. The proposed approach involves segmenting difference images into variable-size and variable-shape blocks and performing segmentation and motion compensation simultaneously. The purpose of obtaining motion vectors for variable-size and variable-shape blocks is to improve the quality of motion estimation, particularly in those areas where the edges of moving objects are situated. For the larger blocks, decimation takes place in order to simplify vector quantization. For very active blocks, which are always of small dimension, a specific vector quantizer has been applied, the fuzzy classified vector quantizer (FCVQ). The coding algorithm described displays good performance in the compression of test sequences at the rates of 8 and 16 kb/s; the signal-to-noise ratios obtained are good in both cases. The complexity of the coder implementation is comparable to that of conventional hybrid coders, while the decoder is much simpler in this proposal.

  9. Triple SV: A Bit Level Symmetric Block-Cipher Having High Avalanche Effect

    Directory of Open Access Journals (Sweden)

    Rajdeep Chakraborty

    2011-08-01

    Full Text Available The prolific growth of network communication system entails high risk of breach in information security. This substantiates the need for higher security for electronic information. Cryptography is one of the ways to secure electronic documents. In this paper, we propose a new block cipher, TRIPLE SV (3SV, with 256-bit block size and 112-bit key length. Generally, stream ciphers produce higher avalanche effect but Triple SV shows a substantial rise in avalanche effect with a block cipher implementation. The CBC mode has been used to attain higher avalanche effect. The technique is implemented in C language and has been tested for feasibility

  10. A 1 GHz sample rate, 256-channel, 1-bit quantization, CMOS, digital correlator chip

    Science.gov (United States)

    Timoc, C.; Tran, T.; Wongso, J.

    1992-01-01

    This paper describes the development of a digital correlator chip with the following features: 1 Giga-sample/second; 256 channels; 1-bit quantization; 32-bit counters providing up to 4 seconds integration time at 1 GHz; and very low power dissipation per channel. The improvements in the performance-to-cost ratio of the digital correlator chip are achieved with a combination of systolic architecture, novel pipelined differential logic circuits, and standard 1.0 micron CMOS process.

  11. A SPEAKER ADAPTABLE VERY LOW BIT RATE SPEECHCODER BASED ON HMM

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    This paper presented a speaker adaptable very low bit rate speech coder based on HMM (Hidden Markov Model) which includes the dynamic features, i.e. , delta and delta-delta parameters of speech. The performance of this speech coder has been improved by using the dynamic features generated by an algorithm for speech parameter generation from HMM because the generated speech parameter vectors reflect not only the means of static and dynamic feature vectors but also the covariance of those. The encoder part is equivalent to an HMM-based phoneme recognizer and transmits phoneme indexes, state durations, pitch information and speaker characteristics adaptation vectors to the decoder. The decoder receives those messages and concatenates phoneme HMM sequence according to the phoneme indexes. Then the decoder generates a sequence of mel-cepstral coefficient vectors using HMM-based speech parameter generation technique. Finally the decoder synthesizes speech by directly exciting the MLSA(Mel Log Spectrum Approximation) filter with the generated mel-cepstral coefficient vectors, according to the pitch information.

  12. IMPROVING THE PERFORMANCE AND REDUCING BIT ERROR RATE ON WIRELESS DEEP FADING ENVIRONMENT RECEIVERS

    Directory of Open Access Journals (Sweden)

    K. Jayanthi

    2014-01-01

    Full Text Available One of the major challenges in wireless communication system is increasing complexity and reducing performance in detecting the received digital information in indoor and outdoor Environments. Consequently to overcome this problem we analyze the delay performance of a multiuser with perfect channel state information transmitting data on deep fading environment. In this proposed system, the Wireless Deep Fading Environment (WDFE creation for causing a Nakagami Multipath Fading Channel of fading figure ‘m’ is used to rectify the delay performance over the existing Rayleigh fading channel. In this WDFE receivers received coherent, synchronized, secured and improved signal strength of information using a Multiuser Coherent Joint Diversity (MCJD with Multi Carrier-Code Division Multiple Access (MC-CDMA. The MCJD in ‘M’ branch of antennas are used to reduce the Bit Error Rate (BER and MC-CDMA method is used to improve the performance. Therefore, in this proposed system we accompany with MCJD and MC-CDMA is very good transceiver for next generation wireless system of an existing 3G wireless system. Overall, this experimental results show improved performance in different multiuser wireless systems under different multipath fading conditions.

  13. Bit Error Rate Performance Analysis on Modulation Techniques of Wideband Code Division Multiple Access

    CERN Document Server

    Masud, M A; Rahman, M A

    2010-01-01

    In the beginning of 21st century there has been a dramatic shift in the market dynamics of telecommunication services. The transmission from base station to mobile or downlink transmission using M-ary Quadrature Amplitude modulation (QAM) and Quadrature phase shift keying (QPSK) modulation schemes are considered in Wideband-Code Division Multiple Access (W-CDMA) system. We have done the performance analysis of these modulation techniques when the system is subjected to Additive White Gaussian Noise (AWGN) and multipath Rayleigh fading are considered in the channel. The research has been performed by using MATLAB 7.6 for simulation and evaluation of Bit Error Rate (BER) and Signal-To-Noise Ratio (SNR) for W-CDMA system models. It is shows that the analysis of Quadrature phases shift key and 16-ary Quadrature Amplitude modulations which are being used in wideband code division multiple access system, Therefore, the system could go for more suitable modulation technique to suit the channel quality, thus we can d...

  14. A bit-rate flexible and power efficient all-optical demultiplexer realised by monolithically integrated Michelson interferometer

    DEFF Research Database (Denmark)

    Vaa, Michael; Mikkelsen, Benny; Jepsen, Kim Stokholm;

    1996-01-01

    A novel bit-rate flexible and very power efficient all-optical demultiplexer using differential optical control of a monolithically integrated Michelson interferometer with MQW SOAs is demonstrated at 40 to 10 Gbit/s. Gain switched DFB lasers provide ultra stable data and control signals....

  15. Reconfigurable Digital Coherent Receiver for Metro-Access Networks Supporting Mixed Modulation Formats and Bit-rates

    DEFF Research Database (Denmark)

    Caballero Jambrina, Antonio; Guerrero Gonzalez, Neil; Arlunno, Valeria

    2013-01-01

    A single, reconfigurable, digital coherent receiver is proposed and experimentally demonstrated for converged wireless and optical fiber transport. The capacity of reconstructing the full transmitted optical field allows for the demodulation of mixed modulation formats and bit-rates. We performed...

  16. Bit error rate analysis of X-ray communication system%X射线通信系统的误码率分析∗

    Institute of Scientific and Technical Information of China (English)

    王律强; 苏桐; 赵宝升; 盛立志; 刘永安; 刘舵

    2015-01-01

    experiment shows that the detected X-ray energy is 7 × 10−5 mW/m2. This relatively low power level not only restricts the bit rate of transceiver, but also increases the error fraction to some extent. Obviously, OOK modulation can meet the high communication rate and relatively low bit-error-rate requirement of current audio demo system. Current restriction has been pointed out and the potential improvement is also presented.

  17. High precision (14 bit), high density (octal) analog to digital converter for spectroscopy applications

    Science.gov (United States)

    Subramaniam, E. T.; Jain, Mamta; Bhowmik, R. K.; Tripon, Michel

    2008-10-01

    Nuclear and particle physics experiments with large number of detectors require signal processing and data collection strategies that call for the ability to collect large amount of data while not sacrificing the precision and accuracy of the data being collected. This paper deals with the development of a high precision pulse peak detection, analog to digital converter (ADC) module with eight independent channels in plug-in daughter card motherboard model, best suited for spectroscopy experiments. This module provides multiple channels without cross-talk and of 14 bit resolution, while maintaining high density (each daughter card has an area of just 4.2″×0.51″) and exhibiting excellent integral nonlinearity (≤±2 mV or ±0.02% full scale reading) and differential nonlinearity (≤±1%). It was designed, developed and tested, in house, and gives added advantages of cost effectiveness and ease of maintenance.

  18. High Data Rate Quantum Cryptography

    Science.gov (United States)

    Kwiat, Paul; Christensen, Bradley; McCusker, Kevin; Kumor, Daniel; Gauthier, Daniel

    2015-05-01

    While quantum key distribution (QKD) systems are now commercially available, the data rate is a limiting factor for some desired applications (e.g., secure video transmission). Most QKD systems receive at most a single random bit per detection event, causing the data rate to be limited by the saturation of the single-photon detectors. Recent experiments have begun to explore using larger degree of freedoms, i.e., temporal or spatial qubits, to optimize the data rate. Here, we continue this exploration using entanglement in multiple degrees of freedom. That is, we use simultaneous temporal and polarization entanglement to reach up to 8.3 bits of randomness per coincident detection. Due to current technology, we are unable to fully secure the temporal degree of freedom against all possible future attacks; however, by assuming a technologically-limited eavesdropper, we are able to obtain 23.4 MB/s secure key rate across an optical table, after error reconciliation and privacy amplification. In this talk, we will describe our high-rate QKD experiment, with a short discussion on our work towards extending this system to ship-to-ship and ship-to-shore communication, aiming to secure the temporal degree of freedom and to implement a 30-km free-space link over a marine environment.

  19. A Very High Bit Rate Broadband Acoustic Modem for Short-to-Medium Range Data Transmission in Ports And Shallow Water Using Spread Spectrum Modulation and Decision Feedback Equalizing

    Science.gov (United States)

    2008-09-30

    using the high-resolution, low-noise acquisition system developed by EdgeTech in collaboration with FAU . The acquisition system produces complex base...direct transducer coupling; (2) System calibration in the acoustic tank at FAU SeaTech; (3) Field tests in the FAU SeaTech marina. During the later...the FAU SeaTech marina on July 25th, 2008 (Figure 3). During the SeaTech demonstration, the source was operating at 32 W of output acoustic power

  20. Design and realization of a high-speed 12-bit pipelined analog-digital converter IP block

    OpenAIRE

    Toprak, Zeynep

    2001-01-01

    This thesis presents the design, verification, system integration and the physical realization of a monolithic high-speed analog-digital converter (ADC) with 12-bit accuracy. The architecture of the ADC has been realized as a pipelined structure consisting of four pipeline stages, each of which is capable of processing the incoming analog signal with 4-bit accuracy. A bit-overlapping technique has been employed for digital error correction between the pipeline stages so that the influence of ...

  1. HDL Design for 1 Zetta Bits Per Second (1 Zbps Multichannel 64:1 LVDS Data Serializer & De-Serializer ASIC Array Card Design for 6th Sense and Future Ultra High Wireless and Mobile Communication Protocol Cards

    Directory of Open Access Journals (Sweden)

    P. N. V. M SASTRY

    2015-01-01

    Full Text Available The Aim is to HDL Design & Implementation for Exa Bit Rate Multichannel 64:1 LVDS Data Serializer & De-Serializer ASIC Array Card for Ultra High Speed Wireless Communication Products like Network On Chip Routers, Data Bus Communication Interface Applications, Cloud Computing Networks , Zetta bit Ethernet at Zetta Bit Rate Of Data Transfer Speed. Basically This Serializer Array Converts 64 bit parallel Data Array in to Serial Array Form on Transmitter Side and Transmission Done through High Speed Wireless Serial Communication Link and also Converts this Same Serial Array Data into Parallel Data Array on the Receiver Side by De-Serializer Array ASIC without any noise, also measure Very High Compressed Jitter Tolerance & Eye Diagram, Bit Error Rate through Analyzer. This LVDS Data SER-De-SER mainly used in High Speed Bus Communication Protocol Transceivers, Interface FPGA Add On Cards. The Process Of Design is Implemented through Verilog HDL / VHDL, Programming & Debugging Done Latest FPGA Board.

  2. High bit rate BPSK signals in shallow water environments

    NARCIS (Netherlands)

    Robert, M.K.; Walree, P.A. van

    2003-01-01

    Lately, acoustic data transfer has become an important topic in underwater environments. Several acoustic communication signals e.g. spread spectrum or frequency shift keying signals have been extensively developed. However, in challenging environments, it is still difficult to obtain robust acousti

  3. High bit rate optical transmission using midspan spectral inversion ...

    African Journals Online (AJOL)

    (LERICA), Département d'Electronique,. Université Badji Mokhtar, BP 12, Annaba 23000, Algerie. Accepté le 28/02/2010. صﺧﻟﻣ. رﺎﺛآ نﻋ ﺔﺟﺗﺎﻧﻟا ءﺎﺿوﺿﻟا ﺔﻟﮐﺷﻣﻟ نﮐﻣﯾ.

  4. A high SFDR 6-bit 20-MS/s SAR ADC based on time-domain comparator

    Institute of Scientific and Technical Information of China (English)

    Han Xue; Fan Hua; Wei Qi; Yang Huazhong

    2013-01-01

    This paper presents a 6-bit 20-MS/s high spurious-free dynamic range (SFDR) and low power successive approximation register analog to digital converter (SAR ADC) for the radio-frequency (RF) transceiver frontend,especially for wireless sensor network (WSN) applications.This ADC adopts the modified common-centroid symmetry layout and the successive approximation register reset circuit to improve the linearity and dynamic range.Prototyped in a 0.18-μm 1P6M CMOS technology,the ADC performs a peak SFDR of 55.32 dB and effective number of bits (ENOB) of 5.1 bit for 10 MS/s.At the sample rate of 20 MS/s and the Nyquist input frequency,the 47.39-dB SFDR and 4.6-ENOB are achieved.The differential nonlinearity (DNL) is less than 0.83 LSB and the integral nonlinearity (INL) is less than 0.82 LSB.The experimental results indicate that this SAR ADC consumes a total of 522 μW power and occupies 0.98 mm2.

  5. Bit Error Rate Performance for Multicarrier Code Division Multiple Access over Generalized η-μ Fading Environment

    Directory of Open Access Journals (Sweden)

    James Osuru Mark

    2011-01-01

    Full Text Available The multicarrier code division multiple access (MC-CDMA system has received a considerable attention from researchers owing to its great potential in achieving high data rates transmission in wireless communications. Due to the detrimental effects of multipath fading the performance of the system degrades. Similarly, the impact of non-orthogonality of spreading codes can exist and cause interference. This paper addresses the performance of multicarrier code division multiple access system under the influence of frequency selective generalized η-µ  fading channel and multiple access interference caused by other active users to the desired one. We apply Gaussian approximation technique to analyse the performance of the system. The avearge bit error rate is derived and expressed in Gauss hypergeometic functions. Maximal ratio combining diversity technique is utilized to alleviate the deleterious effect of multipath fading. We observed that the system performance improves when the parameter η increase or decreasse in format 1 or format 2 conditions respectively.

  6. Two-level renegotiated constant bit rate algorithm (2RCBR) for scalable MPEG2 video over QoS networks

    Science.gov (United States)

    Pegueroles, Josep R.; Alins, Juan J.; de la Cruz, Luis J.; Mata, Jorge

    2001-07-01

    MPEG family codecs generate variable-bit-rate (VBR) compressed video with significant multiple-time-scale bit rate variability. Smoothing techniques remove the periodic fluctuations generated by the codification modes. However, global efficiency concerning network resource allocation remains low due to scene-time-scale variability. RCBR techniques provide suitable means to achieving higher efficiency. Among all RCBR techniques described in literature, 2RCBR mechanism seems to be especially suitable for video-on demand. The method takes advantage of the knowledge of the stored video to calculate the renegotiation intervals and of the client buffer memory to perform work-ahead buffering techniques. 2RCBR achieves 100% bandwidth global efficiency with only two renegotiation levels. The algorithm is based on the study of the second derivative of the cumulative video sequence to find out sharp-sloped inflection points that point out changes in the scene complexity. Due to its nature, 2RCBR becomes very adequate to deliver MPEG2 scalable sequences into the network cause it can assure a constant bit rate to the base MPEG2 layer and use the higher rate intervals to deliver the enhanced MPEG2 layer. However, slight changes in the algorithm parameters must be introduced to attain an optimal behavior. This is verified by means of simulations on MPEG2 video patterns.

  7. Adaptive Long-Term Coding of LSF Parameters Trajectories for Large-Delay/Very- to Ultra-Low Bit-Rate Speech Coding

    Directory of Open Access Journals (Sweden)

    Laurent Girin

    2010-01-01

    Full Text Available This paper presents a model-based method for coding the LSF parameters of LPC speech coders on a “long-term” basis, that is, beyond the usual 20–30 ms frame duration. The objective is to provide efficient LSF quantization for a speech coder with large delay but very- to ultra-low bit-rate (i.e., below 1 kb/s. To do this, speech is first segmented into voiced/unvoiced segments. A Discrete Cosine model of the time trajectory of the LSF vectors is then applied to each segment to capture the LSF interframe correlation over the whole segment. Bi-directional transformation from the model coefficients to a reduced set of LSF vectors enables both efficient “sparse” coding (using here multistage vector quantizers and the generation of interpolated LSF vectors at the decoder. The proposed method provides up to 50% gain in bit-rate over frame-by-frame quantization while preserving signal quality and competes favorably with 2D-transform coding for the lower range of tested bit rates. Moreover, the implicit time-interpolation nature of the long-term coding process provides this technique a high potential for use in speech synthesis systems.

  8. Compact high-performance MWIR camera with exposure control and 12-bit video processor

    Science.gov (United States)

    Villani, Thomas S.; Loesser, Kenneth A.; Perna, Steve N.; McCarthy, D. R.; Pantuso, Francis P.

    1998-07-01

    The design and performance of a compact infrared camera system is presented. The 3 - 5 micron MWIR imaging system consists of a Stirling-cooled 640 X 480 staring PtSi infrared focal plane array (IRFPA) with a compact, high-performance 12-bit digital image processor. The low-noise CMOS IRFPA is X-Y addressable, utilizes on-chip-scanning registers and has electronic exposure control. The digital image processor uses 16-frame averaged, 2-point non-uniformity compensation and defective pixel substitution circuitry. There are separate 12- bit digital and analog I/O ports for display control and video output. The versatile camera system can be configured in NTSC, CCIR, and progressive scan readout formats and the exposure control settings are digitally programmable.

  9. A MODIFIED UNEQUAL POWER ALLOCATION (UPA SCHEME FOR PERFORMANCE ENHANCEMENT IN BIT REPETITION TURBO CODES IN HIGH SPEED DOWNLINK PACKET ACCESS (HSDPA SYSTEM

    Directory of Open Access Journals (Sweden)

    B. BALAMURALITHARA

    2015-06-01

    Full Text Available In this paper, a modified optimal power allocation scheme for different bits in turbo encoder has been proposed to improve the performance of Turbo Codes system in High Speed Downlink Packet Access (HSDPA service. In a typical turbo code in HSDPA system, an encoder with code rate of 1/3 was used with bit repetition scheme or puncturing system to achieve code rate of 1/4. In this study, the author has proposed a modified unequal power allocation (UPA scheme to improve the performance of Turbo Codes in HSDPA system. The simulation and performance bound results for the proposed UPA scheme for the frame length of N = 400, code rate = 1/4 with Log-MAP decoder over Additive White Gaussian Noise (AWGN channel were obtained and compared with the typical Turbo Codes systems, which used bit repetition scheme and puncturing method without UPA. From the results, the proposed bit repetition turbo codes system with modified UPA scheme showed better performance than the typical turbo codes system without UPA using bit repetition and puncturing approaches with coding gain of 0.35 dB to 0.56 dB.

  10. High Lightweight Encryption Standard (HLES as an Improvement of 512-Bit AES for Secure Multimedia

    Directory of Open Access Journals (Sweden)

    GUESMIA Seyf Eddine

    2016-01-01

    Full Text Available In today’s scenario, people share information to another people frequently using network. Due to this, more amount of information are so much private but some are less private. Therefore, the attackers or the hackers take the advantage and start attempting to steal the information since 2001. the symmetric encryption algorithm called 512-bit AES provides high level of security, but it's almost be impossible to be used in multimedia transmissions and mobile systems because of the need for more design area that effect in the use of large memory space in each round and the big encryption time that it takes. This paper presents an improvement of 512-bit AES algorithm with efficient utilization of resources such as processor and memory space. The proposed approach resists the linear and differential encrypt analysis and provides high security level using a 512-bit size of key block and data block and ameliorates the performance by minimizing the use of memory space and time encryption to be able to work in specific characteristics of resource-limited systems. The experimental results on several data (text, image, sound, video show that the used memory space is reduced to quarter, and the encryption time is reduced almost to the half. Therefore, the adopted method is very effective for encryption of multimedia data.

  11. FODA/IBEA satellite access scheme for MIXED traffic at variable bit and coding rates system description

    OpenAIRE

    Celandroni, Nedo; Ferro, Erina; Mihal, Vlado; Potort?, Francesco

    1992-01-01

    This report describes the FODA system working at variable coding and bit rates (FODA/IBEA-TDMA) FODA/IBEA is the natural evolution of the FODA-TDMA satellite access scheme working at 2 Mbit/s fixed rate with data 1/2 coded or uncoded. FODA-TDMA was used in the European SATINE-II experiment [8]. We remind here that the term FODA/IBEA system is comprehensive of the FODA/IBEA-TDMA (1) satellite access scheme and of the hardware prototype realised by the Marconi R.C. (U.K.). Both of them come fro...

  12. FODA/IBEA satellite access scheme for MIXED traffic at variable bit and coding rates system description

    OpenAIRE

    Celandroni, Nedo; Ferro, Erina; Mihal, Vlado; Potort?, Francesco

    1992-01-01

    This report describes the FODA system working at variable coding and bit rates (FODA/IBEA-TDMA) FODA/IBEA is the natural evolution of the FODA-TDMA satellite access scheme working at 2 Mbit/s fixed rate with data 1/2 coded or uncoded. FODA-TDMA was used in the European SATINE-II experiment [8]. We remind here that the term FODA/IBEA system is comprehensive of the FODA/IBEA-TDMA (1) satellite access scheme and of the hardware prototype realised by the Marconi R.C. (U.K.). Both of them come fro...

  13. DRILL BITS FOR HORIZONTAL WELLS

    Directory of Open Access Journals (Sweden)

    Paolo Macini

    1996-12-01

    Full Text Available This paper underlines the importance of the correct drill bit application in horizontal wells. Afler the analysis of the peculiarities of horizontal wells and drainholes drilling techniques, advantages and disadvantages of the application of both roller cone and fixed cutters drill bits have been discussed. Also, a review of the potential specific featuries useful for a correct drill bit selection in horizontal small diameter holes has been highlighted. Drill bits for these special applications, whose importance is quickly increasing nowadays, should be characterised by a design capable to deliver a good penetration rate low WOB, and, at the same time, be able to withstand high RPM without premature cutting structure failure and undergauge. Formation properties will also determine the cutting structure type and the eventual specific features for additional gauge and shoulder protection.

  14. Realization of High-Order Filters for 1-bit Signal Processing Based on Delta-Sigma Modulation

    Science.gov (United States)

    Murahashi, Yoshimitsu; Doki, Shinji; Okuma, Shigeru

    We discuss a realization method of basic 1-bit signal processing based on Delta-Sigma modulation in this paper. Additionally, we show the characteristics of basic 1-bit processor and an effective design method from the view point of SNR. As the application of the 1-bit signal processing, we proposed a realization method of high-order filters based on Delta-Sigma modulation. We applied the effective design method to decide coefficients of a 4th-order butterworth low pass filter. We show that the filter designed by using the proposed method achieves the highest SNR.

  15. Bit error rate analysis of free-space optical communication over general Malaga turbulence channels with pointing error

    KAUST Repository

    Alheadary, Wael G.

    2016-12-24

    In this work, we present a bit error rate (BER) and achievable spectral efficiency (ASE) performance of a freespace optical (FSO) link with pointing errors based on intensity modulation/direct detection (IM/DD) and heterodyne detection over general Malaga turbulence channel. More specifically, we present exact closed-form expressions for adaptive and non-adaptive transmission. The closed form expressions are presented in terms of generalized power series of the Meijer\\'s G-function. Moreover, asymptotic closed form expressions are provided to validate our work. In addition, all the presented analytical results are illustrated using a selected set of numerical results.

  16. Influence of beam wander on bit-error rate in a ground-to-satellite laser uplink communication system.

    Science.gov (United States)

    Ma, Jing; Jiang, Yijun; Tan, Liying; Yu, Siyuan; Du, Wenhe

    2008-11-15

    Based on weak fluctuation theory and the beam-wander model, the bit-error rate of a ground-to-satellite laser uplink communication system is analyzed, in comparison with the condition in which beam wander is not taken into account. Considering the combined effect of scintillation and beam wander, optimum divergence angle and transmitter beam radius for a communication system are researched. Numerical results show that both of them increase with the increment of total link margin and transmitted wavelength. This work can benefit the ground-to-satellite laser uplink communication system design.

  17. Implementation of Convolution Encoder and Viterbi Decoder for Constraint Length 7 and Bit Rate 1/2

    Directory of Open Access Journals (Sweden)

    Mr. Sandesh Y.M

    2013-11-01

    Full Text Available Convolutional codes are non blocking codes that can be designed to either error detecting or correcting. Convolution coding has been used in communication systems including deep space communication and wireless communication. At the receiver end the original message sequence is obtained from the received data using Viterbi decoder. It implements Viterbi Algorithm which is a maximum likelihood algorithm, based on the minimum cumulative hamming distance it decides the optimal trellis path that is most likely followed at the encoder. In this paper I present the convolution encoder and Viterbi decoder for constraint length 7 and bit rate 1/2.

  18. Accurate Bit-Error Rate Evaluation for TH-PPM Systems in Nakagami Fading Channels Using Moment Generating Functions

    Science.gov (United States)

    Liang, Bin; Gunawan, Erry; Law, Choi Look; Teh, Kah Chan

    Analytical expressions based on the Gauss-Chebyshev quadrature (GCQ) rule technique are derived to evaluate the bit-error rate (BER) for the time-hopping pulse position modulation (TH-PPM) ultra-wide band (UWB) systems under a Nakagami-m fading channel. The analyses are validated by the simulation results and adopted to assess the accuracy of the commonly used Gaussian approximation (GA) method. The influence of the fading severity on the BER performance of TH-PPM UWB system is investigated.

  19. Bit rate and pulse width dependence of four-wave mixing of short optical pulses in semiconductor optical amplifiers

    DEFF Research Database (Denmark)

    Diez, S.; Mecozzi, A.; Mørk, Jesper

    1999-01-01

    We investigate the saturation properties of four-wave mixing of short optical pulses in a semiconductor optical amplifier. By varying the gain of the optical amplifier, we find a strong dependence of both conversion efficiency and signal-to-background ratio on pulse width and bit rate....... In particular, the signal-to-background ratio can be optimized for a specific amplifier gain. This behavior, which is coherently described in experiment and theory, is attributed to the dynamics of the amplified spontaneous emission, which is the main source of noise in a semiconductor optical amplifier....

  20. An optical ultrafast random bit generator

    Science.gov (United States)

    Kanter, Ido; Aviad, Yaara; Reidler, Igor; Cohen, Elad; Rosenbluh, Michael

    2010-01-01

    The generation of random bit sequences based on non-deterministic physical mechanisms is of paramount importance for cryptography and secure communications. High data rates also require extremely fast generation rates and robustness to external perturbations. Physical generators based on stochastic noise sources have been limited in bandwidth to ~100 Mbit s-1 generation rates. We present a physical random bit generator, based on a chaotic semiconductor laser, having time-delayed self-feedback, which operates reliably at rates up to 300 Gbit s-1. The method uses a high derivative of the digitized chaotic laser intensity and generates the random sequence by retaining a number of the least significant bits of the high derivative value. The method is insensitive to laser operational parameters and eliminates the necessity for all external constraints such as incommensurate sampling rates and laser external cavity round trip time. The randomness of long bit strings is verified by standard statistical tests.

  1. Accurate Time-Dependent Traveling-Wave Tube Model Developed for Computational Bit-Error-Rate Testing

    Science.gov (United States)

    Kory, Carol L.

    2001-01-01

    The phenomenal growth of the satellite communications industry has created a large demand for traveling-wave tubes (TWT's) operating with unprecedented specifications requiring the design and production of many novel devices in record time. To achieve this, the TWT industry heavily relies on computational modeling. However, the TWT industry's computational modeling capabilities need to be improved because there are often discrepancies between measured TWT data and that predicted by conventional two-dimensional helical TWT interaction codes. This limits the analysis and design of novel devices or TWT's with parameters differing from what is conventionally manufactured. In addition, the inaccuracy of current computational tools limits achievable TWT performance because optimized designs require highly accurate models. To address these concerns, a fully three-dimensional, time-dependent, helical TWT interaction model was developed using the electromagnetic particle-in-cell code MAFIA (Solution of MAxwell's equations by the Finite-Integration-Algorithm). The model includes a short section of helical slow-wave circuit with excitation fed by radiofrequency input/output couplers, and an electron beam contained by periodic permanent magnet focusing. A cutaway view of several turns of the three-dimensional helical slow-wave circuit with input/output couplers is shown. This has been shown to be more accurate than conventionally used two-dimensional models. The growth of the communications industry has also imposed a demand for increased data rates for the transmission of large volumes of data. To achieve increased data rates, complex modulation and multiple access techniques are employed requiring minimum distortion of the signal as it is passed through the TWT. Thus, intersymbol interference (ISI) becomes a major consideration, as well as suspected causes such as reflections within the TWT. To experimentally investigate effects of the physical TWT on ISI would be

  2. Hardware Implementation of 32-Bit High-Speed Direct Digital Frequency Synthesizer

    Directory of Open Access Journals (Sweden)

    Salah Hasan Ibrahim

    2014-01-01

    Full Text Available The design and implementation of a high-speed direct digital frequency synthesizer are presented. A modified Brent-Kung parallel adder is combined with pipelining technique to improve the speed of the system. A gated clock technique is proposed to reduce the number of registers in the phase accumulator design. The quarter wave symmetry technique is used to store only one quarter of the sine wave. The ROM lookup table (LUT is partitioned into three 4-bit sub-ROMs based on angular decomposition technique and trigonometric identity. Exploiting the advantages of sine-cosine symmetrical attributes together with XOR logic gates, one sub-ROM block can be removed from the design. These techniques, compressed the ROM into 368 bits. The ROM compressed ratio is 534.2 : 1, with only two adders, two multipliers, and XOR-gates with high frequency resolution of 0.029 Hz. These techniques make the direct digital frequency synthesizer an attractive candidate for wireless communication applications.

  3. Hardware implementation of 32-bit high-speed direct digital frequency synthesizer.

    Science.gov (United States)

    Ibrahim, Salah Hasan; Ali, Sawal Hamid Md; Islam, Md Shabiul

    2014-01-01

    The design and implementation of a high-speed direct digital frequency synthesizer are presented. A modified Brent-Kung parallel adder is combined with pipelining technique to improve the speed of the system. A gated clock technique is proposed to reduce the number of registers in the phase accumulator design. The quarter wave symmetry technique is used to store only one quarter of the sine wave. The ROM lookup table (LUT) is partitioned into three 4-bit sub-ROMs based on angular decomposition technique and trigonometric identity. Exploiting the advantages of sine-cosine symmetrical attributes together with XOR logic gates, one sub-ROM block can be removed from the design. These techniques, compressed the ROM into 368 bits. The ROM compressed ratio is 534.2:1, with only two adders, two multipliers, and XOR-gates with high frequency resolution of 0.029 Hz. These techniques make the direct digital frequency synthesizer an attractive candidate for wireless communication applications.

  4. Adaptive Power and Bit Allocation in Multicarrier Systems

    Institute of Scientific and Technical Information of China (English)

    HUO Yong-qing; PENG Qi-cong; SHAO Huai-zong

    2007-01-01

    We present two adaptive power and bit allocation algorithms for multicarrier systems in a frequency selective fading environment. One algorithm allocates bit based on maximizing the channel capacity, another allocates bit based on minimizing the bit-error-rate(BER). Two algorithms allocate power based on minimizing the BER. Results show that the proposed algorithms are more effective than Fischer's algorithm at low average signal-to-noise ration (SNR). This indicates that our algorithms can achieve high spectral efficiency and high communication reliability during bad channel state. Results also denote the bit and power allocation of each algorithm and effects of the number of subcarriers on the BER performance.

  5. Bit Error Rate Due to Misalignment of Earth Station Antenna Pointing to Satellite

    Directory of Open Access Journals (Sweden)

    Wahyu Pamungkas

    2010-04-01

    Full Text Available One problem causing reduction of energy in satellite communications system is the misalignment of earth station antenna pointing to satellite. Error in pointing would affect the quality of information signal to energy bit in earth station. In this research, error in pointing angle occurred only at receiver (Rx antenna, while the transmitter (Tx antennas precisely point to satellite. The research was conducted towards two satellites, namely TELKOM-1 and TELKOM-2. At first, measurement was made by directing Tx antenna precisely to satellite, resulting in an antenna pattern shown by spectrum analyzer. The output from spectrum analyzers is drawn with the right scale to describe swift of azimuth and elevation pointing angle towards satellite. Due to drifting from the precise pointing, it influenced the received link budget indicated by pattern antenna. This antenna pattern shows reduction of power level received as a result of pointing misalignment. As a conclusion, the increasing misalignment of pointing to satellite would affect in the reduction of received signal parameters link budget of down-link traffic.

  6. Design and Implementation of 16-Bit Magnitude Comparator Using Efficient Low Power High Performance Full Adders

    Directory of Open Access Journals (Sweden)

    Ajaykumar S Kulkarni

    2014-08-01

    Full Text Available In VLSI applications, area, delay and power are the important factors which must be taken into account in the design of a fast adder [1]. The paper attempts to examine the features of certain adder circuits which promise superior performance compared to existing circuits. The advantages of these circuits are low-power consumption, a high degree of regularity and simplicity. In this paper, the design of a 16-bit comparator is proposed. Magnitude comparison is one of the basic functions used for sorting in microprocessor, digital signal processing, so a high performance, effective magnitude comparator is required. The main objective of this paper is to provide new low power, area solution for Very Large Scale Integration (VLSI designers using low power high performance efficient full adders.

  7. High-resolution image digitizing through 12x3-bit RGB-filtered CCD camera

    Science.gov (United States)

    Cheng, Andrew Y. S.; Pau, Michael C. Y.

    1996-09-01

    A high resolution computer-controlled CCD image capturing system is developed by using a 12 bits 1024 by 1024 pixels CCD camera and motorized RGB filters to grasp an image with color depth up to 36 bits. The filters distinguish the major components of color and collect them separately while the CCD camera maintains the spatial resolution and detector filling factor. The color separation can be done optically rather than electronically. The operation is simply by placing the capturing objects like color photos, slides and even x-ray transparencies under the camera system, the necessary parameters such as integration time, mixing level and light intensity are automatically adjusted by an on-line expert system. This greatly reduces the restrictions of the capturing species. This unique approach can save considerable time for adjusting the quality of image, give much more flexibility of manipulating captured object even if it is a 3D object with minimal setup fixers. In addition, cross sectional dimension of a 3D capturing object can be analyzed by adapting a fiber optic ring light source. It is particularly useful in non-contact metrology of a 3D structure. The digitized information can be stored in an easily transferable format. Users can also perform a special LUT mapping automatically or manually. Applications of the system include medical images archiving, printing quality control, 3D machine vision, and etc.

  8. Stinger Enhanced Drill Bits For EGS

    Energy Technology Data Exchange (ETDEWEB)

    Durrand, Christopher J. [Novatek International, Inc., Provo, UT (United States); Skeem, Marcus R. [Novatek International, Inc., Provo, UT (United States); Crockett, Ron B. [Novatek International, Inc., Provo, UT (United States); Hall, David R. [Novatek International, Inc., Provo, UT (United States)

    2013-04-29

    The project objectives were to design, engineer, test, and commercialize a drill bit suitable for drilling in hard rock and high temperature environments (10,000 meters) likely to be encountered in drilling enhanced geothermal wells. The goal is provide a drill bit that can aid in the increased penetration rate of three times over conventional drilling. Novatek has sought to leverage its polycrystalline diamond technology and a new conical cutter shape, known as the Stinger®, for this purpose. Novatek has developed a fixed bladed bit, known as the JackBit®, populated with both shear cutter and Stingers that is currently being tested by major drilling companies for geothermal and oil and gas applications. The JackBit concept comprises a fixed bladed bit with a center indenter, referred to as the Jack. The JackBit has been extensively tested in the lab and in the field. The JackBit has been transferred to a major bit manufacturer and oil service company. Except for the attached published reports all other information is confidential.

  9. Comparison of Bit Error Rate Performance of Multi Tone Channel Utilising De-OQPSK and De-Off Set 16 QAM with Guard Interval

    Directory of Open Access Journals (Sweden)

    Ibrahim A.Z. Qatawneh

    2005-01-01

    Full Text Available Digital communications systems use Multi tone Channel (MC transmission techniques with differentially encoded and differentially coherent demodulation. Today there are two principle MC application, one is for the high speed digital subscriber loop and the other is for the broadcasting of digital audio and video signals. In this study the comparison of multi carriers with OQPSK and Offset 16 QAM for high-bit rate wireless applications are considered. The comparison of Bit Error Rate (BER performance of Multi tone Channel (MC with offset quadrature amplitude modulation (Offset 16 QAM and offset quadrature phase shift keying modulation (OQPSK with guard interval in a fading environment is considered via the use of Monte Carlo simulation methods. BER results are presented for Offset 16 QAM using guard interval to immune the multi path delay for frequency Rayleigh fading channels and for two-path fading channels in the presence of Additive White Gaussian Noise (AWGN. The BER results are presented for Multi tone Channel (MC with differentially Encoded offset 16 Quadrature Amplitude Modulation (offset 16 QAM and MC with differentially Encoded offset quadrature phase shift keying modulation (OQPSK using guard interval for frequency flat Rician channel in the presence of Additive White Gaussian Noise (AWGN. The performance of multitone systems is also compared with equivalent differentially Encoded offset quadrature amplitude modulation (Offset 16 QAM and differentially Encoded offset quadrature phase shift keying modulation (OQPSKwith and without guard interval in the same fading environment.

  10. Superior bit error rate and jitter due to improved switching field distribution in exchange spring magnetic recording media.

    Science.gov (United States)

    Suess, D; Fuger, M; Abert, C; Bruckner, F; Vogler, C

    2016-06-01

    We report two effects that lead to a significant reduction of the switching field distribution in exchange spring media. The first effect relies on a subtle mechanism of the interplay between exchange coupling between soft and hard layers and anisotropy that allows significant reduction of the switching field distribution in exchange spring media. This effect reduces the switching field distribution by about 30% compared to single-phase media. A second effect is that due to the improved thermal stability of exchange spring media over single-phase media, the jitter due to thermal fluctuation is significantly smaller for exchange spring media than for single-phase media. The influence of this overall improved switching field distribution on the transition jitter in granular recording and the bit error rate in bit-patterned magnetic recording is discussed. The transition jitter in granular recording for a distribution of Khard values of 3% in the hard layer, taking into account thermal fluctuations during recording, is estimated to be a = 0.78 nm, which is similar to the best reported calculated jitter in optimized heat-assisted recording media.

  11. Method of joint bit rate/modulation format identification and optical performance monitoring using asynchronous delay-tap sampling for radio-over-fiber systems

    Science.gov (United States)

    Guesmi, Latifa; Menif, Mourad

    2016-08-01

    In the context of carrying a wide variety of modulation formats and data rates for home networks, the study covers the radio-over-fiber (RoF) technology, where the need for an alternative way of management, automated fault diagnosis, and formats identification is expressed. Also, RoF signals in an optical link are impaired by various linear and nonlinear effects including chromatic dispersion, polarization mode dispersion, amplified spontaneous emission noise, and so on. Hence, for this purpose, we investigated the sampling method based on asynchronous delay-tap sampling in conjunction with a cross-correlation function for the joint bit rate/modulation format identification and optical performance monitoring. Three modulation formats with different data rates are used to demonstrate the validity of this technique, where the identification accuracy and the monitoring ranges reached high values.

  12. Advanced Communications Technology Satellite (ACTS) Fade Compensation Protocol Impact on Very Small-Aperture Terminal Bit Error Rate Performance

    Science.gov (United States)

    Cox, Christina B.; Coney, Thom A.

    1999-01-01

    The Advanced Communications Technology Satellite (ACTS) communications system operates at Ka band. ACTS uses an adaptive rain fade compensation protocol to reduce the impact of signal attenuation resulting from propagation effects. The purpose of this paper is to present the results of an analysis characterizing the improvement in VSAT performance provided by this protocol. The metric for performance is VSAT bit error rate (BER) availability. The acceptable availability defined by communication system design specifications is 99.5% for a BER of 5E-7 or better. VSAT BER availabilities with and without rain fade compensation are presented. A comparison shows the improvement in BER availability realized with rain fade compensation. Results are presented for an eight-month period and for 24 months spread over a three-year period. The two time periods represent two different configurations of the fade compensation protocol. Index Terms-Adaptive coding, attenuation, propagation, rain, satellite communication, satellites.

  13. Bit Error-Rate Minimizing Detector for Amplify-and-Forward Relaying Systems Using Generalized Gaussian Kernel

    KAUST Repository

    Ahmed, Qasim Zeeshan

    2013-01-01

    In this letter, a new detector is proposed for amplifyand- forward (AF) relaying system when communicating with the assistance of relays. The major goal of this detector is to improve the bit error rate (BER) performance of the receiver. The probability density function is estimated with the help of kernel density technique. A generalized Gaussian kernel is proposed. This new kernel provides more flexibility and encompasses Gaussian and uniform kernels as special cases. The optimal window width of the kernel is calculated. Simulations results show that a gain of more than 1 dB can be achieved in terms of BER performance as compared to the minimum mean square error (MMSE) receiver when communicating over Rayleigh fading channels.

  14. Novel ultra-wideband photonic signal generation and transmission featuring digital signal processing bit error rate measurements

    DEFF Research Database (Denmark)

    Gibbon, Timothy Braidwood; Yu, Xianbin; Tafur Monroy, Idelfonso

    2009-01-01

    We propose the novel generation of photonic ultra-wideband signals using an uncooled DFB laser. For the first time we experimentally demonstrate bit-for-bit DSP BER measurements for transmission of a 781.25 Mbit/s photonic UWB signal.......We propose the novel generation of photonic ultra-wideband signals using an uncooled DFB laser. For the first time we experimentally demonstrate bit-for-bit DSP BER measurements for transmission of a 781.25 Mbit/s photonic UWB signal....

  15. High-Order Entropy Compressed Bit Vectors with Rank/Select

    Directory of Open Access Journals (Sweden)

    Kai Beskers

    2014-11-01

    Full Text Available We design practical implementations of data structures for compressing bit-vectors to support efficient rank-queries (counting the number of ones up to a given point. Unlike previous approaches, which either store the bit vectors plainly, or focus on compressing bit-vectors with low densities of ones or zeros, we aim at low entropies of higher order, for example 101010...10. Our implementations achieve very good compression ratios, while showing only a modest increase in query time.

  16. A 1.5 ns OFF/ON switching-time voltage-mode LVDS driver/receiver pair for asynchronous AER bit-serial chip grid links with up to 40 times event-rate dependent power savings.

    Science.gov (United States)

    Zamarreno-Ramos, Carlos; Kulkarni, Raghavendra; Silva-Martinez, Jose; Serrano-Gotarredona, Teresa; Linares-Barranco, Bernabe

    2013-10-01

    This paper presents a low power fast ON/OFF switchable voltage mode implementation of a driver/receiver pair intended to be used in high speed bit-serial Low Voltage Differential Signaling (LVDS) Address Event Representation (AER) chip grids, where short (like 32-bit) sparse data packages are transmitted. Voltage-Mode drivers require intrinsically half the power of their Current-Mode counterparts and do not require Common-Mode Voltage Control. However, for fast ON/OFF switching a special high-speed voltage regulator is required which needs to be kept ON during data pauses, and hence its power consumption must be minimized, resulting in tight design constraints. A proof-of-concept chip test prototype has been designed and fabricated in low-cost standard 0.35 μ m CMOS. At ± 500 mV voltage swing with 500 Mbps serial bit rate and 32 bit events, current consumption scales from 15.9 mA (7.7 mA for the driver and 8.2 mA for the receiver) at 10 Mevent/s rate to 406 μ A ( 343 μ A for the driver and 62.5 μA for the receiver) for an event rate below 10 Kevent/s, therefore achieving a rate dependent power saving of up to 40 times, while keeping switching times at 1.5 ns. Maximum achievable event rate was 13.7 Meps at 638 Mbps serial bit rate. Additionally, differential voltage swing is tunable, thus allowing further power reductions.

  17. Digital sound: The selection of critical programme material and preparation of recordings for CCIR tests on low bit-rate codecs

    Science.gov (United States)

    Gilchrist, N. H. C.

    A draft of a new recommendation on low bit-rate digital audio coding for broadcasting is in preparation within CCIR Study Group 10. As part of this work, subjective tests are being conducted to determine the preferred coding systems to be used in the various applications, and at which bit rates they should be used. The BBC has been contributing to the work by conducting preliminary listening tests to select critical program material, and by preparing recordings using this material for use by the CCIR's testing centers.

  18. Forensic watermarking and bit-rate conversion of partially encrypted AAC bitstreams

    Science.gov (United States)

    Lemma, Aweke; Katzenbeisser, Stefan; Celik, Mehmet U.; Kirbiz, S.

    2008-02-01

    Electronic Music Distribution (EMD) is undergoing two fundamental shifts. The delivery over wired broadband networks to personal computers is being replaced by delivery over heterogeneous wired and wireless networks, e.g. 3G and Wi-Fi, to a range of devices such as mobile phones, game consoles and in-car players. Moreover, restrictive DRM models bound to a limited set of devices are being replaced by flexible standards-based DRM schemes and increasingly forensic tracking technologies based on watermarking. Success of these EMD services will partially depend on scalable, low-complexity and bandwidth eficient content protection systems. In this context, we propose a new partial encryption scheme for Advanced Audio Coding (AAC) compressed audio which is particularly suitable for emerging EMD applications. The scheme encrypts only the scale-factor information in the AAC bitstream with an additive one-time-pad. This allows intermediate network nodes to transcode the bitstream to lower data rates without accessing the decryption keys, by increasing the scale-factor values and re-quantizing the corresponding spectral coeficients. Furthermore, the decryption key for each user is customized such that the decryption process imprints the audio with a unique forensic tracking watermark. This constitutes a secure, low-complexity watermark embedding process at the destination node, i.e. the player. As opposed to server-side embedding methods, the proposed scheme lowers the computational burden on servers and allows for network level bandwidth saving measures such as multi-casting and caching.

  19. Measurement of low bit-error-rates of adiabatic quantum-flux-parametron logic using a superconductor voltage driver

    Science.gov (United States)

    Takeuchi, Naoki; Suzuki, Hideo; Yoshikawa, Nobuyuki

    2017-05-01

    Adiabatic quantum-flux-parametron (AQFP) is an energy-efficient superconductor logic. The advantage of AQFP is that the switching energy can be reduced by lowering operation frequencies or by increasing the quality factors of Josephson junctions, while keeping the energy barrier height much larger than thermal energy. In other words, both low energy dissipation and low bit error rates (BERs) can be achieved. In this paper, we report the first measurement results of the low BERs of AQFP logic. We used a superconductor voltage driver with a stack of dc superconducting-quantum-interference-devices to amplify the logic signals of AQFP gates into mV-range voltage signals for the BER measurement. Our measurement results showed 3.3 dB and 2.6 dB operation margins, in which BERs were less than 10-20, for 1 Gbps and 2 Gbps data rates, respectively. While the observed BERs were very low, the estimated switching energy for the 1-Gbps operation was only 2 zJ or 30kBT, where kB is the Boltzmann's constant and T is the temperature. Unlike conventional non-adiabatic logic, BERs are not directly associated with switching energy in AQFP.

  20. Bit error rate estimation for galvanic-type intra-body communication using experimental eye-diagram and jitter characteristics.

    Science.gov (United States)

    Li, Jia Wen; Chen, Xi Mei; Pun, Sio Hang; Mak, Peng Un; Gao, Yue Ming; Vai, Mang I; Du, Min

    2013-01-01

    Bit error rate (BER), which indicates the reliability of communicate channel, is one of the most important values in all kinds of communication system, including intra-body communication (IBC). In order to know more about IBC channel, this paper presents a new method of BER estimation for galvanic-type IBC using experimental eye-diagram and jitter characteristics. To lay the foundation for our methodology, the fundamental relationships between eye-diagram, jitter and BER are first reviewed. Then experiments based on human lower arm IBC are carried out using quadrature phase shift keying (QPSK) modulation scheme and 500 KHz carries frequency. In our IBC experiments, the symbol rate is from 10 Ksps to 100 Ksps, with two transmitted power settings, 0 dBm and -5 dBm. Finally, the BER results were obtained after calculation by experimental data through the relationships among eye-diagram, jitter and BER. These results are then compared with theoretical values and they show good agreement, especially when SNR is between 6 dB to 11 dB. Additionally, these results demonstrate assuming the noise of galvanic-type IBC channel as Additive White Gaussian Noise (AWGN) in previous study is applicable.

  1. Cross-Layer Resource Allocation for Variable Bit Rate Multiclass Services in a Multirate Multicarrier DS-CDMA Network

    Directory of Open Access Journals (Sweden)

    Kee-Chaing Chua

    2005-02-01

    Full Text Available An approximate analytical formulation of the resource allocation problem for handling variable bit rate multiclass services in a cellular round-robin carrier-hopping multirate multicarrier direct-sequence code-division multiple-access (MC-DS-CDMA system is presented. In this paper, all grade-of-service (GoS or quality-of-service (QoS requirements at the connection level, packet level, and link layer are satisfied simultaneously in the system, instead of being satisfied at the connection level or at the link layer only. The analytical formulation shows how the GoS/QoS in the different layers are intertwined across the layers. A novelty of this paper is that the outages in the subcarriers are minimized by spreading the subcarriers' signal-to-interference ratio evenly among all the subcarriers by using a dynamic round-robin carrier-hopping allocation scheme. A complete sharing (CS scheme with guard capacity is used for the resource sharing policy at the connection level based on the mean rates of the connections. Numerical results illustrate that significant gain in the system utilization is achieved through the joint coupling of connection/packet levels and link layer.

  2. Resolution of digital servo control system using single-bit digital signal processing; 1 bit digital shingo shori wo mochiita seigyo no bunkaino to johoryo ni tsuite no simulation

    Energy Technology Data Exchange (ETDEWEB)

    Tojo, K.; Kurosawa, M.; Oka, K.; Higuchi, T. [The University of Tokyo, Tokyo (Japan)

    1998-05-01

    The application of single-bit digital signal processing to mechanical control system has already been proposed by the authors. Multi-bit A/D converter has been improved to the high level. But it is difficult to make more high resolution A/D by latest semiconductor technologies. There is single-bit digital signal which is generated by a delta-sigma modulator. Single-bit digital signal has small quantized error around low frequency. Then with this single-bit digital signal processing, high resolution on controlling such a narrow band width mechanical system will be realized. In this paper, resolution of analog, multi-bit and single-bit control systems are estimated with simulation. According to simulations` results, single-bit control system has higher resolution than multi-bit system in the condition of equal bit rate. 5 refs., 17 figs., 1 tab.

  3. Bit error rate analysis of Wi-Fi and bluetooth under the interference of 2.45 GHz RFID

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    IEEE 802.11b WLAN (Wi-Fi) and IEEE 802.15.1 WPAN (bluetooth) are prevalent nowadays, and radio frequency identification (RFID) is an emerging technology which has wider applications. 802.11b occupies unlicensed industrial, scientific and medical (ISM) band (2.4-2.483 5 GHz) and uses direct sequence spread spectrum (DSSS) to alleviate the narrow band interference and fading. Bluetooth is also one user of ISM band and adopts frequency hopping spread spectrum (FHSS) to avoid the mutual interference. RFID can operate on multiple frequency bands, such as 135 KHz, 13.56 MHz and 2.45 GHz. When 2.45 GHz RFID device, which uses FHSS, collocates with 802.11b or bluetooth, the mutual interference is inevitable. Although DSSS and FHSS are applied to mitigate the interference, their performance degradation may be very significant. Therefore, in this article, the impact of 2.45 GHz RFID on 802.11b and bluetooth is investigated. Bit error rate (BER) of 802.11b and bluetooth are analyzed by establishing a mathematical model, and the simula-tion results are compared with the theoretical analysis to justify this mathematical model.

  4. N-dimensional measurement-device-independent quantum key distribution with N + 1 un-characterized sources: zero quantum-bit-error-rate case.

    Science.gov (United States)

    Hwang, Won-Young; Su, Hong-Yi; Bae, Joonwoo

    2016-01-01

    We study N-dimensional measurement-device-independent quantum-key-distribution protocol where one checking state is used. Only assuming that the checking state is a superposition of other N sources, we show that the protocol is secure in zero quantum-bit-error-rate case, suggesting possibility of the protocol. The method may be applied in other quantum information processing.

  5. metaBIT, an integrative and automated metagenomic pipeline for analysing microbial profiles from high-throughput sequencing shotgun data.

    Science.gov (United States)

    Louvel, Guillaume; Der Sarkissian, Clio; Hanghøj, Kristian; Orlando, Ludovic

    2016-11-01

    Micro-organisms account for most of the Earth's biodiversity and yet remain largely unknown. The complexity and diversity of microbial communities present in clinical and environmental samples can now be robustly investigated in record times and prices thanks to recent advances in high-throughput DNA sequencing (HTS). Here, we develop metaBIT, an open-source computational pipeline automatizing routine microbial profiling of shotgun HTS data. Customizable by the user at different stringency levels, it performs robust taxonomy-based assignment and relative abundance calculation of microbial taxa, as well as cross-sample statistical analyses of microbial diversity distributions. We demonstrate the versatility of metaBIT within a range of published HTS data sets sampled from the environment (soil and seawater) and the human body (skin and gut), but also from archaeological specimens. We present the diversity of outputs provided by the pipeline for the visualization of microbial profiles (barplots, heatmaps) and for their characterization and comparison (diversity indices, hierarchical clustering and principal coordinates analyses). We show that metaBIT allows an automatic, fast and user-friendly profiling of the microbial DNA present in HTS shotgun data sets. The applications of metaBIT are vast, from monitoring of laboratory errors and contaminations, to the reconstruction of past and present microbiota, and the detection of candidate species, including pathogens.

  6. Analysis of bit-rock interaction during stick-slip vibrations using PDC cutting force model

    Energy Technology Data Exchange (ETDEWEB)

    Patil, P.A.; Teodoriu, C. [Technische Univ. Clausthal, Clausthal-Zellerfeld (Germany). ITE

    2013-08-01

    Drillstring vibration is one of the limiting factors maximizing the drilling performance and also causes premature failure of drillstring components. Polycrystalline diamond compact (PDC) bit enhances the overall drilling performance giving the best rate of penetrations with less cost per foot but the PDC bits are more susceptible to the stick slip phenomena which results in high fluctuations of bit rotational speed. Based on the torsional drillstring model developed using Matlab/Simulink for analyzing the parametric influence on stick-slip vibrations due to drilling parameters and drillstring properties, the study of relations between weight on bit, torque on bit, bit speed, rate of penetration and friction coefficient have been analyzed. While drilling with the PDC bits, the bit-rock interaction has been characterized by cutting forces and the frictional forces. The torque on bit and the weight on bit have both the cutting component and the frictional component when resolved in horizontal and vertical direction. The paper considers that the bit is undergoing stick-slip vibrations while analyzing the bit-rock interaction of the PDC bit. The Matlab/Simulink bit-rock interaction model has been developed which gives the average cutting torque, T{sub c}, and friction torque, T{sub f}, values on cutters as well as corresponding average weight transferred by the cutting face, W{sub c}, and the wear flat face, W{sub f}, of the cutters value due to friction.

  7. A global rate-distortion optimized approach for H.26L low bit rate robust video over the Internet

    Institute of Scientific and Technical Information of China (English)

    Yang Hua; Yu Songyu; Yang Songan

    2005-01-01

    In recent years, more and more applications of video communication over the Internet have been extended, so the demand for reliable transmission of compressed video in a packet loss environment is ever increasing. Rate-Distortion optimized mode selection is a fundamental problem of video communication over packet-switched networks, but the classical R-D method only considers quantization distortion in the source and hence it cannot achieve global optimality. Here we introduce a new global R-D optimal Macro-Block coding mode decision scheme for the new H.26L video compression standard. Based on the Internet packet loss model of Bernoulli and Gilbert, this R-D mode decision approach can result in better error robustness than classical method. Furthermore, our experimental results also demonstrate its superior adaptive error resilience and feasibility.

  8. 16 Bits DAC s Design, Simulation and Layout

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The high speed and precision 16 bits DAC will be applied in DSP (Digital Signal Processing) based on CSR pulsed power supply control system. In this application the DAC is needed to work in 1 μs’ converting data rate, 16 bit resolution and its output voltage is 10 volts.

  9. GPU Kernels for High-Speed 4-Bit Astrophysical Data Processing

    CERN Document Server

    Klages, Peter; Denman, Nolan; Recnik, Andre; Sievers, Jonathan; Vanderlinde, Keith

    2015-01-01

    Interferometric radio telescopes often rely on computationally expensive O(N^2) correlation calculations; fortunately these computations map well to massively parallel accelerators such as low-cost GPUs. This paper describes the OpenCL kernels developed for the GPU based X-engine of a new hybrid FX correlator. Channelized data from the F-engine is supplied to the GPUs as 4-bit, offset-encoded real and imaginary integers. Because of the low bit width of the data, two values may be packed into a 32-bit register, allowing multiplication and addition of more than one value with a single fused multiply-add instruction. With this data and calculation packing scheme, as many as 5.6 effective tera-operations per second (TOPS) can be executed on a 4.3 TOPS GPU. The kernel design allows correlations to scale to large numbers of input elements, limited only by maximum buffer sizes on the GPU. This code is currently working on-sky with the CHIME Pathfinder Correlator in BC, Canada.

  10. High Performance Computing of Three-Dimensional Finite Element Codes on a 64-bit Machine

    Directory of Open Access Journals (Sweden)

    M.P Raju

    2012-01-01

    Full Text Available Three dimensional Navier-Stokes finite element formulations require huge computational power in terms of memory and CPU time. Recent developments in sparse direct solvers have significantly reduced the memory and computational time of direct solution methods. The objective of this study is twofold. First is to evaluate the performance of various state-of-the-art sequential sparse direct solvers in the context of finite element formulation of fluid flow problems. Second is to examine the merit in upgrading from 32 bit machine to a 64 bit machine with larger RAM capacity in terms of its capacity to solve larger problems. The choice of a direct solver is dependent on its computational time and its in-core memory requirements. Here four different solvers, UMFPACK, MUMPS, HSL_MA78 and PARDISO are compared. The performances of these solvers with respect to the computational time and memory requirements on a 64-bit windows server machine with 16GB RAM is evaluated.

  11. High frame rate measurements of semiconductor pixel detector readout IC

    Science.gov (United States)

    Szczygiel, R.; Grybos, P.; Maj, P.

    2012-07-01

    We report on high count rate and high frame rate measurements of a prototype IC named FPDR90, designed for readouts of hybrid pixel semiconductor detectors used for X-ray imaging applications. The FPDR90 is constructed in 90 nm CMOS technology and has dimensions of 4 mm×4 mm. Its main part is a matrix of 40×32 pixels with 100 μm×100 μm pixel size. The chip works in the single photon counting mode with two discriminators and two 16-bit ripple counters per pixel. The count rate per pixel depends on the effective CSA feedback resistance and can be set up to 6 Mcps. The FPDR90 can operate in the continuous readout mode, with zero dead time. Due to the architecture of digital blocks in pixel, one can select the number of bits read out from each counter from 1 to 16. Because in the FPDR90 prototype only one data output is available, the frame rate is 9 kfps and 72 kfps for 16 bits and 1 bit readout, respectively (with nominal clock frequency of 200 MHz).

  12. High frame rate measurements of semiconductor pixel detector readout IC

    Energy Technology Data Exchange (ETDEWEB)

    Szczygiel, R., E-mail: robert.szczygiel@agh.edu.pl [AGH University of Science and Technology, Department of Measurement and Instrumentation, Al. Mickiewicza 30, 30-059 Cracow (Poland); Grybos, P.; Maj, P. [AGH University of Science and Technology, Department of Measurement and Instrumentation, Al. Mickiewicza 30, 30-059 Cracow (Poland)

    2012-07-11

    We report on high count rate and high frame rate measurements of a prototype IC named FPDR90, designed for readouts of hybrid pixel semiconductor detectors used for X-ray imaging applications. The FPDR90 is constructed in 90 nm CMOS technology and has dimensions of 4 mm Multiplication-Sign 4 mm. Its main part is a matrix of 40 Multiplication-Sign 32 pixels with 100 {mu}m Multiplication-Sign 100 {mu}m pixel size. The chip works in the single photon counting mode with two discriminators and two 16-bit ripple counters per pixel. The count rate per pixel depends on the effective CSA feedback resistance and can be set up to 6 Mcps. The FPDR90 can operate in the continuous readout mode, with zero dead time. Due to the architecture of digital blocks in pixel, one can select the number of bits read out from each counter from 1 to 16. Because in the FPDR90 prototype only one data output is available, the frame rate is 9 kfps and 72 kfps for 16 bits and 1 bit readout, respectively (with nominal clock frequency of 200 MHz).

  13. Analytical bit error rate performance evaluation of an orthogonal frequency division multiplexing power line communication system impaired by impulsive and Gaussian channel noise

    OpenAIRE

    Munshi Mahbubur Rahman; Satya Prasad Majumder

    2015-01-01

    An analytical approach is presented to evaluate the bit error rate (BER) performance of a power line (PL) communication system considering the combined influence of impulsive noise and background PL Gaussian noise. Middleton class-A noise model is considered to evaluate the effect of impulsive noise. The analysis is carried out to find the expression of the signal-to-noise ratio and BER considering orthogonal frequency division multiplexing (OFDM) with binary phase shift keying modulation wit...

  14. 20 Gb/s WDM-OFDM-PON over 20-km single fiber uplink transmission using optical millimeter-wave signal seeding with rate adaptive bit-power loading

    Science.gov (United States)

    Kartiwa, Iwa; Jung, Sang-Min; Hong, Moon-Ki; Han, Sang-Kook

    2013-06-01

    We experimentally demonstrate the use of millimeter-wave signal generation by optical carrier suppression (OCS) method using single-drive Mach-Zehnder modulator as a light sources seed for 20 Gb/s WDM-OFDM-PON in 20-km single fiber loopback transmission based on cost-effective RSOA modulation. Practical discrete rate adaptive bit loading algorithm was employed in this colorless ONU system to maximize the achievable bit rate for an average bit error rate (BER) below 2 × 10-3.

  15. Quantum data locking for high-rate private communication

    Science.gov (United States)

    Lupo, Cosmo; Lloyd, Seth

    2015-03-01

    We show that, if the accessible information is used as a security quantifier, quantum channels with a certain symmetry can convey private messages at a tremendously high rate, as high as less than one bit below the rate of non-private classical communication. This result is obtained by exploiting the quantum data locking effect. The price to pay to achieve such a high private communication rate is that accessible information security is in general not composable. However, composable security holds against an eavesdropper who is forced to measure her share of the quantum system within a finite time after she gets it.

  16. VLSI Design of Low Power High Speed 4 Bit Resolution Pipeline ADC In Submicron CMOS Technology

    Directory of Open Access Journals (Sweden)

    Rita M. Shende

    2012-01-01

    Full Text Available Analog-to-digital converters (ADCs are key design blocks and are currently adopted in many application fields to improve digital systems, which achieve superior performances with respect to analog solutions. Application such as wireless communication and digital audio and video have created the need for costeffective data converters that will achieve higher speed and resolution. Widespread usage confers great importance to the design activities, which nowadays largely contributes to the production cost in integrated circuit devices (ICs. Various examples of ADC applications can be found in data acquisition systems, measurement systems and digital communication systems also imaging, instrumentation systems. Since theADC has a continuous, infinite –valued signal as its input, the important analog points on the transfer curve x-axis for an ADC are the ones that corresponding to changes in the digital output word. These input transitions determine the amount of INL and DNL associated with the converter. Hence, we have to considered all the parameters and improving the associated performance may significantly reduce the industrial cost of an ADC manufacturing process and improved the resolution and design specially powerconsumption . The paper presents a design of 4 bit Pipeline ADC with low power dissipation implemented in <0.18µm.

  17. Bit-error-rate performance analysis of self-heterodyne detected radio-over-fiber links using phase and intensity modulation

    DEFF Research Database (Denmark)

    Yin, Xiaoli; Yu, Xianbin; Tafur Monroy, Idelfonso

    2010-01-01

    We theoretically and experimentally investigate the performance of two self-heterodyne detected radio-over-fiber (RoF) links employing phase modulation (PM) and quadrature biased intensity modulation (IM), in term of bit-error-rate (BER) and optical signal-to-noise-ratio (OSNR). In both links, self......-heterodyne receivers perform down-conversion of radio frequency (RF) subcarrier signal. A theoretical model including noise analysis is constructed to calculate the Q factor and estimate the BER performance. Furthermore, we experimentally validate our prediction in the theoretical modeling. Both the experimental...

  18. Bit-error-rate performance analysis of self-heterodyne detected radio-over-fiber links using phase and intensity modulation

    DEFF Research Database (Denmark)

    Yin, Xiaoli; Yu, Xianbin; Tafur Monroy, Idelfonso

    2010-01-01

    -heterodyne receivers perform down-conversion of radio frequency (RF) subcarrier signal. A theoretical model including noise analysis is constructed to calculate the Q factor and estimate the BER performance. Furthermore, we experimentally validate our prediction in the theoretical modeling. Both the experimental......We theoretically and experimentally investigate the performance of two self-heterodyne detected radio-over-fiber (RoF) links employing phase modulation (PM) and quadrature biased intensity modulation (IM), in term of bit-error-rate (BER) and optical signal-to-noise-ratio (OSNR). In both links, self...

  19. High rate drift chambers

    Energy Technology Data Exchange (ETDEWEB)

    Christian, D.C. (Fermilab, Batavia, IL 60510 (United States)); Berisso, M.C. (Fermilab, Batavia, IL 60510 (United States)); Gutierrez, G. (Fermilab, Batavia, IL 60510 (United States)); Holmes, S.D. (Fermilab, Batavia, IL 60510 (United States)); Wehmann, A. (Fermilab, Batavia, IL 60510 (United States)); Avilez, C. (Instituto de Fisica, Universidad de Guanajuato, Leon, Guanajuato (Mexico)); Felix, J. (Instituto de Fisica, Universidad de Guanajuato, Leon, Guanajuato (Mexico)); Moreno, G. (Instituto de Fisica, Universidad de Guanajuato, Leon, Guanajuato (Mexico)); Romero, M. (Instituto de Fisica, Universidad de Guanajuato, Leon, Guanajuato (Mexico)); Sosa, M. (Instituto de Fisica, Universidad de Guanajuato, Leon, Guanajuato (Mexico)); Forbush, M. (Department of Physics, Texas A and M University, College Station, TX 77843 (United States)); Huson, F.R. (Department of Physics, Texas A and M University, College Station, TX 77843 (United States)); Wightman, J.A. (Department of Physi

    1994-06-01

    Fermilab experiment 690, a study of target dissociation reactions pp[yields]pX using an 800 GeV/c proton beam and a liquid hydrogen target, collected data in late 1991. The incident beam and 600-800 GeV/c scattered protons were measured using a system of six 6 in.x4 in. and two 15 in.x8 in. pressurized drift chambers spaced over 260 m. These chambers provided precise measurements at rates above 10 MHz (2 MHz per cm of sense wire). The measurement resolution of the smaller chambers was 90 [mu]m, and the resolution of the larger chambers was 125 [mu]m. Construction details and performance results, including radiation damage, are presented. ((orig.))

  20. An Architecture for High Data Rate Very Low Frequency Communication

    Directory of Open Access Journals (Sweden)

    Arun Kumar

    2013-01-01

    Full Text Available Very low frequency (VLF communication is used for long range shore-to-ship broadcasting applications. This paper proposes an architecture for high data rate VLF communication using Gaussian minimum shift keying (GMSK modulation and low delay parity check (LDPC channel coding. Non-data aided techniques are designed and used for carrier phase synchronization, symbol timing recovery, and LDPC code frame synchronization. These require the estimation of the operative Eb/N0 for which a kurtosis based algorithm is used. Also, a method for modeling the probability density function of the received signal under the bit condition is presented in this regard. The modeling of atmospheric radio noise (ARN that corrupts VLF signals is described and an algorithm for signal enhancement in the presence of ARN in given. The BER performance of the communication system is evaluated for bit rates of 400 bps, 600 bps, and 800 bps for communication bandwidth of ~200 Hz.

  1. Adjustable Nyquist-rate System for Single-Bit Sigma-Delta ADC with Alternative FIR Architecture

    Science.gov (United States)

    Frick, Vincent; Dadouche, Foudil; Berviller, Hervé

    2016-09-01

    This paper presents a new smart and compact system dedicated to control the output sampling frequency of an analogue-to-digital converters (ADC) based on single-bit sigma-delta (ΣΔ) modulator. This system dramatically improves the spectral analysis capabilities of power network analysers (power meters) by adjusting the ADC's sampling frequency to the input signal's fundamental frequency with a few parts per million accuracy. The trade-off between straightforwardness and performance that motivated the choice of the ADC's architecture are preliminary discussed. It particularly comes along with design considerations of an ultra-steep direct-form FIR that is optimised in terms of size and operating speed. Thanks to compact standard VHDL language description, the architecture of the proposed system is particularly suitable for application-specific integrated circuit (ASIC) implementation-oriented low-power and low-cost power meter applications. Field programmable gate array (FPGA) prototyping and experimental results validate the adjustable sampling frequency concept. They also show that the system can perform better in terms of implementation and power capabilities compared to dedicated IP resources.

  2. Dose-rate and total-dose radiation testing of the Texas Instruments TMS320C30 32-bit floating point digital signal processor. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Siy, P.F.; Carter, J.T.; D' Addario, L.R.; Loeber, D.A.

    1991-08-01

    The MITRE Corporation has performed in-flux radiation testing of the Texas Instruments TMS320C30 32-bit floating point digital signal processor in both total dose and dose rate radiation environments. This test effort has provided data relating to the applicability of the TMS320C30 in systems with total dose and/or dose rate survivability requirements. In order to accomplish these tests, the MITRE Corporation developed custom hardware and software for in-flux radiation testing. This paper summarizes the effort by providing an overview of the TMS320C30, MITRE's test methodology, test facilities, statistical analysis, and full coverage of the test results. (Author)

  3. Characterization of semiconductor-laser phase noise and estimation of bit-error rate performance with low-speed offline digital coherent receivers.

    Science.gov (United States)

    Kikuchi, Kazuro

    2012-02-27

    We develop a systematic method for characterizing semiconductor-laser phase noise, using a low-speed offline digital coherent receiver. The field spectrum, the FM-noise spectrum, and the phase-error variance measured with such a receiver can completely describe phase-noise characteristics of lasers under test. The sampling rate of the digital coherent receiver should be much higher than the phase-fluctuation speed. However, 1 GS/s is large enough for most of the single-mode semiconductor lasers. In addition to such phase-noise characterization, interpolating the taken data at 1.25 GS/s to form a data stream at 10 GS/s, we can predict the bit-error rate (BER) performance of multi-level modulated optical signals at 10 Gsymbol/s. The BER degradation due to the phase noise is well explained by the result of the phase-noise measurements.

  4. A 12-bit high-speed column-parallel two-step single-slope analog-to-digital converter (ADC) for CMOS image sensors.

    Science.gov (United States)

    Lyu, Tao; Yao, Suying; Nie, Kaiming; Xu, Jiangtao

    2014-11-17

    A 12-bit high-speed column-parallel two-step single-slope (SS) analog-to-digital converter (ADC) for CMOS image sensors is proposed. The proposed ADC employs a single ramp voltage and multiple reference voltages, and the conversion is divided into coarse phase and fine phase to improve the conversion rate. An error calibration scheme is proposed to correct errors caused by offsets among the reference voltages. The digital-to-analog converter (DAC) used for the ramp generator is based on the split-capacitor array with an attenuation capacitor. Analysis of the DAC's linearity performance versus capacitor mismatch and parasitic capacitance is presented. A prototype 1024 × 32 Time Delay Integration (TDI) CMOS image sensor with the proposed ADC architecture has been fabricated in a standard 0.18 μm CMOS process. The proposed ADC has average power consumption of 128 μW and a conventional rate 6 times higher than the conventional SS ADC. A high-quality image, captured at the line rate of 15.5 k lines/s, shows that the proposed ADC is suitable for high-speed CMOS image sensors.

  5. Joint Machine Learning and Game Theory for Rate Control in High Efficiency Video Coding.

    Science.gov (United States)

    Gao, Wei; Kwong, Sam; Jia, Yuheng

    2017-08-25

    In this paper, a joint machine learning and game theory modeling (MLGT) framework is proposed for inter frame coding tree unit (CTU) level bit allocation and rate control (RC) optimization in High Efficiency Video Coding (HEVC). First, a support vector machine (SVM) based multi-classification scheme is proposed to improve the prediction accuracy of CTU-level Rate-Distortion (R-D) model. The legacy "chicken-and-egg" dilemma in video coding is proposed to be overcome by the learning-based R-D model. Second, a mixed R-D model based cooperative bargaining game theory is proposed for bit allocation optimization, where the convexity of the mixed R-D model based utility function is proved, and Nash bargaining solution (NBS) is achieved by the proposed iterative solution search method. The minimum utility is adjusted by the reference coding distortion and frame-level Quantization parameter (QP) change. Lastly, intra frame QP and inter frame adaptive bit ratios are adjusted to make inter frames have more bit resources to maintain smooth quality and bit consumption in the bargaining game optimization. Experimental results demonstrate that the proposed MLGT based RC method can achieve much better R-D performances, quality smoothness, bit rate accuracy, buffer control results and subjective visual quality than the other state-of-the-art one-pass RC methods, and the achieved R-D performances are very close to the performance limits from the FixedQP method.

  6. 14-bit pipeline-SAR ADC for image sensor readout circuits

    Science.gov (United States)

    Wang, Gengyun; Peng, Can; Liu, Tianzhao; Ma, Cheng; Ding, Ning; Chang, Yuchun

    2015-03-01

    A two stage 14bit pipeline-SAR analog-to-digital converter includes a 5.5bit zero-crossing MDAC and a 9bit asynchronous SAR ADC for image sensor readout circuits built in 0.18um CMOS process is described with low power dissipation as well as small chip area. In this design, we employ comparators instead of high gain and high bandwidth amplifier, which consumes as low as 20mW of power to achieve the sampling rate of 40MSps and 14bit resolution.

  7. A 8 bits Pipeline Analog to Digital Converter Design for High Speed Camera Application

    CERN Document Server

    Prasetyo, Eri; Ginhac, Nurul Huda Dominique; Paindavoine, Michel

    2008-01-01

    - This paper describes a pipeline analog-to-digital converter is implemented for high speed camera. In the pipeline ADC design, prime factor is designing operational amplifier with high gain so ADC have been high speed. The other advantage of pipeline is simple on concept, easy to implement in layout and have flexibility to increase speed. We made design and simulation using Mentor Graphics Software with 0.6 \\mu m CMOS technology with a total power dissipation of 75.47 mW. Circuit techniques used include a precise comparator, operational amplifier and clock management. A switched capacitor is used to sample and multiplying at each stage. Simulation a worst case DNL and INL of 0.75 LSB. The design operates at 5 V dc. The ADC achieves a SNDR of 44.86 dB. keywords: pipeline, switched capacitor, clock management

  8. A forward error correction technique using a high-speed, high-rate single chip codec

    Science.gov (United States)

    Boyd, R. W.; Hartman, W. F.; Jones, Robert E.

    1989-01-01

    The authors describe an error-correction coding approach that allows operation in either burst or continuous modes at data rates of multiple hundreds of megabits per second. Bandspreading is low since the code rate is 7/8 or greater, which is consistent with high-rate link operation. The encoder, along with a hard-decision decoder, fits on a single application-specific integrated circuit (ASIC) chip. Soft-decision decoding is possible utilizing applique hardware in conjunction with the hard-decision decoder. Expected coding gain is a function of the application and is approximately 2.5 dB for hard-decision decoding at 10-5 bit-error rate with phase-shift-keying modulation and additive Gaussian white noise interference. The principal use envisioned for this technique is to achieve a modest amount of coding gain on high-data-rate, bandwidth-constrained channels. Data rates of up to 300 Mb/s can be accommodated by the codec chip. The major objective is burst-mode communications, where code words are composed of 32 n data bits followed by 32 overhead bits.

  9. Bit error rate analysis of free-space optical system with spatial diversity over strong atmospheric turbulence channel with pointing errors

    Science.gov (United States)

    Krishnan, Prabu; Sriram Kumar, D.

    2014-12-01

    Free-space optical communication (FSO) is emerging as a captivating alternative to work out the hindrances in the connectivity problems. It can be used for transmitting signals over common lands and properties that the sender or receiver may not own. The performance of an FSO system depends on the random environmental conditions. The bit error rate (BER) performance of differential phase shift keying FSO system is investigated. A distributed strong atmospheric turbulence channel with pointing error is considered for the BER analysis. Here, the system models are developed for single-input, single-output-FSO (SISO-FSO) and single-input, multiple-output-FSO (SIMO-FSO) systems. The closed-form mathematical expressions are derived for the average BER with various combining schemes in terms of the Meijer's G function.

  10. Bit-Table Based Biclustering and Frequent Closed Itemset Mining in High-Dimensional Binary Data

    Directory of Open Access Journals (Sweden)

    András Király

    2014-01-01

    Full Text Available During the last decade various algorithms have been developed and proposed for discovering overlapping clusters in high-dimensional data. The two most prominent application fields in this research, proposed independently, are frequent itemset mining (developed for market basket data and biclustering (applied to gene expression data analysis. The common limitation of both methodologies is the limited applicability for very large binary data sets. In this paper we propose a novel and efficient method to find both frequent closed itemsets and biclusters in high-dimensional binary data. The method is based on simple but very powerful matrix and vector multiplication approaches that ensure that all patterns can be discovered in a fast manner. The proposed algorithm has been implemented in the commonly used MATLAB environment and freely available for researchers.

  11. Directed self-assembly of high-chi block copolymer for nano fabrication of bit patterned media via solvent annealing

    Science.gov (United States)

    Xiong, Shisheng; Chapuis, Yves-Andre; Wan, Lei; Gao, He; Li, Xiao; Ruiz, Ricardo; Nealey, Paul F.

    2016-10-01

    We report the formation of nanoimprint master templates that can be used for the fabrication of bit patterned media (BPM). The template was formed by directed self-assembly, with solvent annealing, of a symmetric ABA triblock copolymer to form perpendicularly oriented lamellae on chemical patterns. We used a high-χ block copolymer, poly(2-vinyl pyridine)-block-polystyrene-block-poly(2-vinyl pyridine) to achieve smaller feature sizes than are possible with polystyrene-block-poly(methyl methacrylate). The work shows that triblock copolymers can provide a large processing window in terms of pitch commensurability. Using block-selective infiltration (atomic layer deposition with sequential long soaking/purge cycles), an alumina composite with high etch resistance was specifically incorporated into the polar and hydrophilic P2VP domains. Subsequently, the surface pattern was successfully transferred into underlying Si substrates by etching with a fluorine-containing plasma to create a nanoimprint master. The line/space pattern of the nanoimprint master met the BPM fabrication requirement of defectivity <10-3. For demonstration purposes, the nanoimprint master was used to imprint a replica pattern of photoresist on a quartz wafer.

  12. Experimental demonstration of real-time adaptively modulated DDO-OFDM systems with a high spectral efficiency up to 5.76bit/s/Hz transmission over SMF links.

    Science.gov (United States)

    Chen, Ming; He, Jing; Tang, Jin; Wu, Xian; Chen, Lin

    2014-07-28

    In this paper, a FPGAs-based real-time adaptively modulated 256/64/16QAM-encoded base-band OFDM transceiver with a high spectral efficiency up to 5.76bit/s/Hz is successfully developed, and experimentally demonstrated in a simple intensity-modulated direct-detection optical communication system. Experimental results show that it is feasible to transmit a raw signal bit rate of 7.19Gbps adaptively modulated real-time optical OFDM signal over 20km and 50km single mode fibers (SMFs). The performance comparison between real-time and off-line digital signal processing is performed, and the results show that there is a negligible power penalty. In addition, to obtain the best transmission performance, direct-current (DC) bias voltage for MZM and launch power into optical fiber links are explored in the real-time optical OFDM systems.

  13. Analyzing the propagation behavior of scintillation index and bit error rate of a partially coherent flat-topped laser beam in oceanic turbulence.

    Science.gov (United States)

    Yousefi, Masoud; Golmohammady, Shole; Mashal, Ahmad; Kashani, Fatemeh Dabbagh

    2015-11-01

    In this paper, on the basis of the extended Huygens-Fresnel principle, a semianalytical expression for describing on-axis scintillation index of a partially coherent flat-topped (PCFT) laser beam of weak to moderate oceanic turbulence is derived; consequently, by using the log-normal intensity probability density function, the bit error rate (BER) is evaluated. The effects of source factors (such as wavelength, order of flatness, and beam width) and turbulent ocean parameters (such as Kolmogorov microscale, relative strengths of temperature and salinity fluctuations, rate of dissipation of the mean squared temperature, and rate of dissipation of the turbulent kinetic energy per unit mass of fluid) on propagation behavior of scintillation index, and, hence, on BER, are studied in detail. Results indicate that, in comparison with a Gaussian beam, a PCFT laser beam with a higher order of flatness is found to have lower scintillations. In addition, the scintillation index and BER are most affected when salinity fluctuations in the ocean dominate temperature fluctuations.

  14. metaBIT, an integrative and automated metagenomic pipeline for analysing microbial profiles from high-throughput sequencing shotgun data

    DEFF Research Database (Denmark)

    Louvel, Guillaume; Der Sarkissian, Clio; Hanghøj, Kristian Ebbesen

    2016-01-01

    -throughput DNA sequencing (HTS). Here, we develop metaBIT, an open-source computational pipeline automatizing routine microbial profiling of shotgun HTS data. Customizable by the user at different stringency levels, it performs robust taxonomy-based assignment and relative abundance calculation of microbial taxa......, as well as cross-sample statistical analyses of microbial diversity distributions. We demonstrate the versatility of metaBIT within a range of published HTS data sets sampled from the environment (soil and seawater) and the human body (skin and gut), but also from archaeological specimens. We present......-friendly profiling of the microbial DNA present in HTS shotgun data sets. The applications of metaBIT are vast, from monitoring of laboratory errors and contaminations, to the reconstruction of past and present microbiota, and the detection of candidate species, including pathogens....

  15. 基于统计模型及SVM的低速率语音编码QIM隐写检测%Detection of QIM Steganography in Low Bit-Rate Speech Codec Based on Statistical Models and SVM

    Institute of Scientific and Technical Information of China (English)

    李松斌; 黄永峰; 卢记仓

    2013-01-01

    QIM(Quantization Index Modulation,量化索引调制)隐写在标量或矢量量化时嵌入机密信息,可在语音压缩编码过程中进行高隐蔽性的信息隐藏,文中试图对该种隐写进行检测.文中发现该种隐写将导致压缩语音流中的音素分布特性发生改变,提出了音素向量空间模型和音素状态转移模型对音素分布特性进行了量化表示.基于所得量化特征并结合SVM(Support Vector Machine,支持向量机)构建了隐写检测器.针对典型的低速率语音编码标准G.729以及G.723.1的实验表明,文中方法性能远优于现有检测方法,实现了对QIM隐写的快速准确检测.%Quantization Index Modulation (QIM) steganography,which embeds the secret information during the Vector Quantization,can hide information in low bit-rate speech codec with high imperceptibility.This paper tries to detect this type of steganography.For this purpose,starting from the speech generation and compress coding theory,this paper firstly analyzes the possible significant feature degradation through the QIM steganography in compressed audio stream deeply.And it finds that the QIM steganography will disturb the phoneme sequence in the stream,and inevitably make the imbalance and correlation characteristics of phoneme distribution in the sequence change.According to this discovery,this paper adopts the phoneme distribution characteristics as the key for the detection of the QIM steganography.In order to get the quantitative features of phoneme distribution characteristics,this paper designs the Phoneme Vector Space Model and the Phoneme State Transition Model to quantify the imbalance and correlation characteristics respectively.By combining the quantitative vector features with supervised learning classifier,this paper builds a high performance detector towards the QIM steganography in low bit-rate speech codec.The experiments show that,for the two typical low bit-rate speech codec:G.729 and G.723.1,the

  16. Influence of partially coherent beam passing through strong turbulence on bit error rate of laser communication systems%部分相干光通过强湍流对通信系统误码率的影响

    Institute of Scientific and Technical Information of China (English)

    王江安; 赵英俊; 吴荣华; 任席闯

    2009-01-01

    A theoretical base for using the technology of multibeam transmission and the reception in the ship laser communication systems was provided by the research on the influence of partially coherent beams passing through the strong turbulence on the bit error rate. The relation between system bit error rate and transmission range was obtained under the conditions of different turbulence measurement, transmission laser wavelength and light source coherence parameter by the aid of a method to parse the equation of laser transmission in atmospheric turbulence field, ignoring other noises in the system, but considering the bit error rate caused by atmospheric turbulence only. The result indicates that under the strong turbulence condition, the system bit error rate is increased gradually with the increase of the transmission range when the quantity of transmitting antennas reaches a certain number, but the system bit error rate tends to saturation when the transmission range accretion reaches a definite degree; the bigger the light source coherence parameter increases, the lower the system bit error rate becomes; the more the turbulence inner scale is, the higher the system bit error rate becomes; and the variation of the transmission laser wavelength has no obvious influence on the system bit error rate.%为研究部分相干光通过强湍流对系统误码率的影响,借助对激光在大气湍流场中的传输方程进行解析求解(忽略系统中其他噪声,仅考虑由大气湍流引起的系统误码率),得到不同湍流内尺度、传输激光波长和光源相干参数条件下,系统误码率和传输距离的关系.结果表明:在强湍流条件下,当发射天线数目达到一定时,随着传输距离的增加,系统误码率逐渐增大,但增大到一定程度后趋于饱和;光源相干参数越大,系统误码率越低;湍流内尺度越大,系统误码率越高;传输激光波长的变化对系统误码率无明显影响.

  17. Bit Error Rate Performance Analysis of a Threshold-Based Generalized Selection Combining Scheme in Nakagami Fading Channels

    Directory of Open Access Journals (Sweden)

    Sulyman Ahmed Iyanda

    2005-01-01

    Full Text Available The severity of fading on mobile communication channels calls for the combining of multiple diversity sources to achieve acceptable error rate performance. Traditional approaches perform the combining of the different diversity sources using either the conventional selective diversity combining (CSC, equal-gain combining (EGC, or maximal-ratio combining (MRC schemes. CSC and MRC are the two extremes of compromise between performance quality and complexity. Some researches have proposed a generalized selection combining scheme (GSC that combines the best M branches out of the L available diversity resources (M ≤ L . In this paper, we analyze a generalized selection combining scheme based on a threshold criterion rather than a fixed-size subset of the best channels. In this scheme, only those diversity branches whose energy levels are above a specified threshold are combined. Closed-form analytical solutions for the BER performances of this scheme over Nakagami fading channels are derived. We also discuss the merits of this scheme over GSC.

  18. A TCP/IP-based constant-bit-rate file transfer protocol and its extension to multipoint data delivery

    Energy Technology Data Exchange (ETDEWEB)

    Yamanaka, Kenjiro, E-mail: yamanaka@nii.ac.jp [National Institute of Informatics, 2-1-2 Hitotsubashi, Chiyoda-ku, Tokyo (Japan); Urushidani, Shigeo [National Institute of Informatics, 2-1-2 Hitotsubashi, Chiyoda-ku, Tokyo (Japan); Nakanishi, Hideya; Yamamoto, Takashi; Nagayama, Yoshio [National Institute of Fusion Science, 322-6 Orochi, Toki, Gifu (Japan)

    2014-05-15

    We present a new TCP/IP-based file transfer protocol which enables high-speed daisy-chain transfer. By using this protocol, we can send a file to a series of destination hosts simultaneously because intermediate hosts relay received file fragments to the next host. We achieved daisy-chain file transfer from Japan to Europe via USA at about 800 Mbps by using a prototype. The experimental result is also reported. A total link length of a data delivery network can be reduced by daisy chaining, so it enables cost-effective international data sharing.

  19. CRUCIAL: Cryosat-2 Success over Inland Water and Land: SAR and SARin Full Bit Rate Altimetric Heights and Validation

    Science.gov (United States)

    Moore, Philip; Birkinshaw, Stephen; Restano, Marco; Ambrozio, Americo; Benveniste, Jerome

    2016-04-01

    CRUCIAL is an ESA/STSE funded project investigating innovative land and inland water applications from Cryosat-2 with a forward-look component to the future Sentinel-3 and Jason-CS/Sentinel-6 missions. The high along-track sampling and resolution of Cryosat-2 altimeter in SAR and SARin modes offer the opportunity to recover high frequency signals over inland waters. This paper will present the theoretical approach to analysis of the FBR L1A Doppler beams to form a product using ground cell gridding, beam steering and beam stacking from which inland water heights are derivable from the retracked Cryosat-2 altimetric waveforms. Details of the processing strategy will include a comparison of waveforms and heights from the burst echoes (~80 m along-track) and from multi-look waveforms (~320 m along-track). SAR and SARin FBR data are available for the Amazon, Brahmaputra and Mekong. The Mekong and Amazon FBR SAR data has been processed for 2011-2015 and results will be compared against stage data from the nearest gauge. Similarly, heights from Tonle Sap will be compared against Jason-2 data from the United States Department of Agriculture web site. A strategy to select the number of multi-looks over rivers will also be presented. Results of FBR SARin processing will be presented including comparison of heights from the two antennae and the extraction of slope of the ground surface.

  20. SOA - NOLM in Reflective Configuration for Optical Regeneration in High Bit Rate Transmission Systems

    CERN Document Server

    Roncin, Vincent; Gay, Mathilde; Bramerie, Laurent; Simon, Jean-Claude

    2014-01-01

    This paper presents a theoretical and experimental investigation of optical signal regeneration properties of a non-linear optical loop mirror using a semiconductor optical amplifier as the active element (SOA-NOLM). While this device has been extensively studied for optical time division demultiplexing (OTDM) and wavelength conversion applications, our proposed approach, based on a reflective configuration, has not yet been investigated, particularly in the light of signal regeneration. The impact on the transfer function shape of different parameters, like SOA position in the interferometer and SOA input optical powers, are numerically studied to appreciate the regenerative capabilities of the device.Regenerative performances in association with a dual stage of SOA to create a 3R regenerator which preserves the data polarity and the wavelength are experimentally assessed. Thanks to this complete regenerative function, a 100.000 km error free transmission has experimentally been achieved at 10 Gb/s in a reci...

  1. Shallow-water acoustic communication with high bit rate BPSK signals

    NARCIS (Netherlands)

    Gijzen, M.B. van; Walree, P.A. van

    2000-01-01

    BPSK signals have been defined for transmission through a shallow-water acoustic communication channel. The signals were accompanied by two displaced carriers to facilitate carrier recovery. To correct for the adverse effects of time spreading, a pseudo-random learning sequence was transmitted ahead

  2. Novel Optical Labeling Scheme for Ultra-High Bit Rate Data Packets

    DEFF Research Database (Denmark)

    Medhin, Ashenafi Kiros; Galili, Michael; Oxenløwe, Leif Katsuo

    2013-01-01

    We propose and verify by simulations an optical in-band labeling scheme for ultra-fast optical switching. The scheme is able to label more than 60 different 640-Gbit/s OTDM packets with eye opening penalty <1 dB.......We propose and verify by simulations an optical in-band labeling scheme for ultra-fast optical switching. The scheme is able to label more than 60 different 640-Gbit/s OTDM packets with eye opening penalty

  3. ZTE IPTV Low Bit Rate High Definition Transcoding Solution Nominated for Global IPTV Industry Award

    Institute of Scientific and Technical Information of China (English)

    2012-01-01

    ZTE Corporation announced on 1 March that its innovative IPTVlowbitrate highdefinition transcoding solution has been nominated for the World's Best Component or Enabler Award by the IPTV World Forum. The ZTE solution is on display at the Mobile World Congress 2012 (MWC 2012) in Barcelona.

  4. Research on the critical parameters initialization of optical PMD compensator in high bit-rate systems

    Science.gov (United States)

    Zhao, Wenyu; Zhang, Haiyi; Ji, Yuefeng; Xu, Daxiong

    2004-05-01

    Based on the proposed polarization mode dispersion (PMD) compensation simulation model and statistical analysis method (Monte-Carlo), the critical parameters initialization of two typical optical domain PMD compensators, which include optical PMD method with fixed compensation differential group delay (DGD) and that with variable compensation DGD, are detailedly investigated by numerical method. In the simulation, the line PMD values are chosen as 3ps, 4ps and 5ps and run samples are set to 1000 in order to achieve statistical evaluation for PMD compensated systems, respectively. The simulation results show that for the PMD value pre-known systems, the value of the fixed DGD compensator should be set to 1.5~1.6 times of line PMD value in order to reach the optimum performance, but for the second kind of PMD compensator, the DGD range of lower limit should be 1.5~1.6 times of line PMD provided that of upper limit is set to 3 times of line PMD, if no effective ways are chosen to resolve the problem of local minimum in optimum process. Another conclusion can be drawn from the simulation is that, although the second PMD compensator holds higher PMD compensation performance, it will spend more feedback loops to look up the optimum DGD value in the real PMD compensation realization, and this will bring more requirements on adjustable DGD device, not only wider adjustable range, but rapid adjusting speed for real time PMD equalization.

  5. Novel Optical Labeling Scheme for Ultra-High Bit Rate Data Packets

    DEFF Research Database (Denmark)

    Medhin, Ashenafi Kiros; Galili, Michael; Oxenløwe, Leif Katsuo

    2013-01-01

    We propose and verify by simulations an optical in-band labeling scheme for ultra-fast optical switching. The scheme is able to label more than 60 different 640-Gbit/s OTDM packets with eye opening penalty <1 dB....

  6. Protected Polycrystalline Diamond Compact Bits For Hard Rock Drilling

    Energy Technology Data Exchange (ETDEWEB)

    Robert Lee Cardenas

    2000-10-31

    Two bits were designed. One bit was fabricated and tested at Terra-Tek's Drilling Research Laboratory. Fabrication of the second bit was not completed due to complications in fabrication and meeting scheduled test dates at the test facility. A conical bit was tested in a Carthage Marble (compressive strength 14,500 psi) and Sierra White Granite (compressive strength 28,200 psi). During the testing, Hydraulic Horsepower, Bit Weight, Rotation Rate, were varied for the Conical Bit, a Varel Tricone Bit and Varel PDC bit. The Conical Bi did cut rock at a reasonable rate in both rocks. Beneficial effects from the near and through cutter water nozzles were not evident in the marble due to test conditions and were not conclusive in the granite due to test conditions. At atmospheric drilling, the Conical Bit's penetration rate was as good as the standard PDC bit and better than the Tricone Bit. Torque requirements for the Conical Bit were higher than that required for the Standard Bits. Spudding the conical bit into the rock required some care to avoid overloading the nose cutters. The nose design should be evaluated to improve the bit's spudding characteristics.

  7. Analytical bit error rate performance evaluation of an orthogonal frequency division multiplexing power line communication system impaired by impulsive and Gaussian channel noise

    Directory of Open Access Journals (Sweden)

    Munshi Mahbubur Rahman

    2015-02-01

    Full Text Available An analytical approach is presented to evaluate the bit error rate (BER performance of a power line (PL communication system considering the combined influence of impulsive noise and background PL Gaussian noise. Middleton class-A noise model is considered to evaluate the effect of impulsive noise. The analysis is carried out to find the expression of the signal-to-noise ratio and BER considering orthogonal frequency division multiplexing (OFDM with binary phase shift keying modulation with coherent demodulation of OFDM sub-channels. The results are evaluated numerically considering the multipath transfer function model of PL with non-flat power spectral density of PL background noise over a bandwidth of 0.3–100 MHz. The results are plotted for several system and noise parameters and penalty because of impulsive noise is determined at a BER of 10^−6. The computed results show that the system suffers significant power penalty because of impulsive noise which is higher at higher channel bandwidth and can be reduced by increasing the number of OFDM subcarriers to some extent. The analytical results conform well with the simulation results reported earlier.

  8. Development of a jet-assisted polycrystalline diamond drill bit

    Energy Technology Data Exchange (ETDEWEB)

    Pixton, D.S.; Hall, D.R.; Summers, D.A.; Gertsch, R.E.

    1997-12-31

    A preliminary investigation has been conducted to evaluate the technical feasibility and potential economic benefits of a new type of drill bit. This bit transmits both rotary and percussive drilling forces to the rock face, and augments this cutting action with high-pressure mud jets. Both the percussive drilling forces and the mud jets are generated down-hole by a mud-actuated hammer. Initial laboratory studies show that rate of penetration increases on the order of a factor of two over unaugmented rotary and/or percussive drilling rates are possible with jet-assistance.

  9. High Reproduction Rate versus Sexual Fidelity

    OpenAIRE

    Sousa, A. O.; de Oliveira, S. Moss

    2000-01-01

    We introduce fidelity into the bit-string Penna model for biological ageing and study the advantage of this fidelity when it produces a higher survival probability of the offspring due to paternal care. We attribute a lower reproduction rate to the faithful males but a higher death probability to the offspring of non-faithful males that abandon the pups to mate other females. The fidelity is considered as a genetic trait which is transmitted to the male offspring (with or without error). We s...

  10. High speed and adaptable error correction for megabit/s rate quantum key distribution.

    Science.gov (United States)

    Dixon, A R; Sato, H

    2014-12-02

    Quantum Key Distribution is moving from its theoretical foundation of unconditional security to rapidly approaching real world installations. A significant part of this move is the orders of magnitude increases in the rate at which secure key bits are distributed. However, these advances have mostly been confined to the physical hardware stage of QKD, with software post-processing often being unable to support the high raw bit rates. In a complete implementation this leads to a bottleneck limiting the final secure key rate of the system unnecessarily. Here we report details of equally high rate error correction which is further adaptable to maximise the secure key rate under a range of different operating conditions. The error correction is implemented both in CPU and GPU using a bi-directional LDPC approach and can provide 90-94% of the ideal secure key rate over all fibre distances from 0-80 km.

  11. Performance evaluation of reactive direct current unbalanced magnetron sputter deposited nanostructured TiN coated high-speed steel drill bits

    Indian Academy of Sciences (India)

    Harish C Barshilia; K S Rajam

    2007-12-01

    The stainless steels, in general, are considered to be difficult-to-machine materials. In order to machine these materials the surface of the tool is generally coated with physical vapour deposition (PVD) hard coatings such as titanium nitride (TiN), titanium aluminum nitride (TiAlN), etc. The adhesion is of vital importance for the performance of tools coated with PVD coatings. Proper surface treatments (in situ and ex situ) are required to achieve highly adherent PVD coatings on tools. We have deposited nanostructured TiN coatings on high-speed steel (HSS) drill bits and mild steel substrates using an indigenously built semi-industrial fourcathode reactive direct current (d.c.) unbalanced magnetron sputtering system. Various treatments have been given to the substrates for improved adhesion of the TiN coatings. The process parameters have been optimized to achieve highly adherent thick good quality TiN coatings. These coatings have been characterized using X-ray diffraction, nanoindentation and atomic force microscopy techniques. The performance of the coated HSS drill bits is evaluated by drilling a 13 mm thick 304 stainless steel plate under wet conditions. The results show significant improvement in the performance of the TiN coated HSS drill bits.

  12. Purpose-built PDC bit successfully drills 7-in liner equipment and formation: An integrated solution

    Energy Technology Data Exchange (ETDEWEB)

    Puennel, J.G.A.; Huppertz, A.; Huizing, J. [and others

    1996-12-31

    Historically, drilling out the 7-in, liner equipment has been a time consuming operation with a limited success ratio. The success of the operation is highly dependent on the type of drill bit employed. Tungsten carbide mills and mill tooth rock bits required from 7.5 to 11.5 hours respectively to drill the pack-off bushings, landing collar, shoe track and shoe. Rates of penetration dropped dramatically when drilling the float equipment. While conventional PDC bits have drilled the liner equipment successfully (averaging 9.7 hours), severe bit damage invariably prevented them from continuing to drill the formation at cost-effective penetration rates. This paper describes the integrated development and application of an IADC M433 Class PDC bit, which was designed specifically to drill out the 7-in. liner equipment and continue drilling the formation at satisfactory penetration rates. The development was the result of a joint investigation There the operator and bit/liner manufacturers shared their expertise in solving a drilling problem, The heavy-set bit was developed following drill-off tests conducted to investigate the drillability of the 7-in. liner equipment. Key features of the new bit and its application onshore The Netherlands will be presented and analyzed.

  13. PERBANDINGAN APLIKASI MENGGUNAKAN METODE CAMELLIA 128 BIT KEY DAN 256 BIT KEY

    Directory of Open Access Journals (Sweden)

    Lanny Sutanto

    2014-01-01

    Full Text Available The rapid development of the Internet today to easily exchange data. This leads to high levels of risk in the data piracy. One of the ways to secure data is using cryptography camellia. Camellia is known as a method that has the encryption and decryption time is fast. Camellia method has three kinds of scale key is 128 bit, 192 bit, and 256 bit.This application is created using the C++ programming language and using visual studio 2010 GUI. This research compare the smallest and largest key size used on the file extension .Txt, .Doc, .Docx, .Jpg, .Mp4, .Mkv and .Flv. This application is made to comparing time and level of security in the use of 128-bit key and 256 bits. The comparison is done by comparing the results of the security value of avalanche effect 128 bit key and 256 bit key.

  14. A Heuristic Optimal Discrete Bit Allocation Algorithm for Margin Maximization in DMT Systems

    Directory of Open Access Journals (Sweden)

    Dong Shi-Wei

    2007-01-01

    Full Text Available A heuristic optimal discrete bit allocation algorithm is proposed for solving the margin maximization problem in discrete multitone (DMT systems. Starting from an initial equal power assignment bit distribution, the proposed algorithm employs a multistaged bit rate allocation scheme to meet the target rate. If the total bit rate is far from the target rate, a multiple-bits loading procedure is used to obtain a bit allocation close to the target rate. When close to the target rate, a parallel bit-loading procedure is used to achieve the target rate and this is computationally more efficient than conventional greedy bit-loading algorithm. Finally, the target bit rate distribution is checked, if it is efficient, then it is also the optimal solution; else, optimal bit distribution can be obtained only by few bit swaps. Simulation results using the standard asymmetric digital subscriber line (ADSL test loops show that the proposed algorithm is efficient for practical DMT transmissions.

  15. An Architecture for High Data Rate Very Low Frequency Communication

    Directory of Open Access Journals (Sweden)

    Arun Kumar

    2013-01-01

    Full Text Available Very low frequency (VLF communication is used for long range shore-to-ship broadcasting applications. This paper proposes an architecture for high data rate VLF communication using Gaussian minimum shift keying (GMSK modulation and low delay parity check (LDPC channel coding. Non-data aided techniques are designed and used for carrier phase synchronization, symbol timing recovery, and LDPC code frame synchronization. These require the estimation of the operative Eb/N0 for which a kurtosis based algorithm is used. Also, a method for modeling the probability density function of the received signal under the bit condition is presented in this regard. The modeling of atmospheric radio noise (ARN that corrupts VLF signals is described and an algorithm for signal enhancement in the presence of ARN in given. The BER performance of the communication system is evaluated for bit rates of 400 bps, 600 bps, and 800 bps for communication bandwidth of ~200 Hz.Defence Science Journal, 2013, 63(1, pp.25-33, DOI:http://dx.doi.org/10.14429/dsj.63.3760

  16. Differentiated Bit Error Rate Estimation for Wireless Networks%无线网络的差异化比特错误率估计方法

    Institute of Scientific and Technical Information of China (English)

    张招亮; 陈海明; 黄庭培; 崔莉

    2014-01-01

    在无线网络中,比特错误率(bit error rate,BER)的估计是许多上层协议的基础,对数据传输的性能具有重要的影响,目前已成为一个重要的研究课题.但是现有BER估计编码未考虑实际网络的BER分布特征,估计误差较大.在实测分析802.11无线网络的BER分布特征的基础上,提出了一种采用差异化思想来提高BER估计准确度的方法差异化估错码(differentiated error estimation,DEE),其主要思想是在数据包中插入具有不同估错能力的多级估错位,并随机均匀地分布各估错位.然后,借助BER与奇偶校验错误概率的理论关系来估计BER.此外,DEE利用BER非均匀分布特征来优化各级估错位的能力,提高出现概率较高的BER的估计准确度,以降低平均估计误差.在7个节点组成的测试床上评价了DEE的性能.实验结果表明,与最近的研究成果估错码(error estimation code,EEC)相比,DEE可将估计误差平均减少约44%.当估错冗余较低时DEE可将估计误差减少约68%.此外,DEE具有比EEC更小的估计偏差.

  17. Design and Analysis of a High Speed, Power Efficient 8 Bit ALU Based on SOI / SON MOSFET Technology

    Directory of Open Access Journals (Sweden)

    Subhramita Basak

    2014-01-01

    Full Text Available This paper shows an overall performance comparative analysis in terms of Average Power Consumption, Average Delay and Power-Delay Product for an 8 bit Arithmetic Logic Unit (ALU using bulk MOS, Silicon-on-Insulator (SOI and Silicon-on-Nothing (SON technology. The entire design is done in 32nm technology for all the three cases (Bulk, SOI & SON and then compared. The comparisons have been carried out with the help of the simulation runs on Synopsys HSpice tool, and that clearly indicates, for lower Supply Voltages (Vdd, SOI / SON technology provides a significant reduction in Average Power Consumption, Average Delay and Power-Delay Product compared to that of Bulk MOS technology.

  18. Analysis and Simulation of Quantum Bit Rate in Satellite Based Quantum Key System%星地量子密钥系统中量子比特率分析与仿真

    Institute of Scientific and Technical Information of China (English)

    赵安廷; 赵黎平

    2011-01-01

    量子比特率是衡量一个量子密钥系统性能优劣的重要参数之一.通过研究星-地量子密钥分配系统中量子链路的持续时间,分析了量子链路持续时间内地面站天线俯仰角的变化情况,在此基础上建立了LEO星-地单光子下行链路的星-地量子比特率模型.仿真结果表明,LEO星-地单光子下行链路的星地量子比特率在每次链路的中心时刻达到极大值.星-地量子比特率能够达到实用的要求,进一步验证了星-地量子密钥分配的可行性.%Quantum bit rate is an important parameter in quantum key distribution system. Quantum link during time in a satellite-to-ground quantum key distribution system was studied, and the variation of pitch angle at facility was analyzed. Then the link model between low earth orbit and earth station was built. By numerical analyzing, it is shown that, quantum bit rate varies with the satellite's movement and in the centre of link, the quantum bit rate reaches the maximal value. The results show that quantum bit rate in an earth-based station and low earth orbit satellite QKD system can reach the practical demand and is feasible.

  19. Double acting bit holder

    Science.gov (United States)

    Morrell, Roger J.; Larson, David A.; Ruzzi, Peter L.

    1994-01-01

    A double acting bit holder that permits bits held in it to be resharpened during cutting action to increase energy efficiency by reducing the amount of small chips produced. The holder consist of: a stationary base portion capable of being fixed to a cutter head of an excavation machine and having an integral extension therefrom with a bore hole therethrough to accommodate a pin shaft; a movable portion coextensive with the base having a pin shaft integrally extending therefrom that is insertable in the bore hole of the base member to permit the moveable portion to rotate about the axis of the pin shaft; a recess in the movable portion of the holder to accommodate a shank of a bit; and a biased spring disposed in adjoining openings in the base and moveable portions of the holder to permit the moveable portion to pivot around the pin shaft during cutting action of a bit fixed in a turret to allow front, mid and back positions of the bit during cutting to lessen creation of small chip amounts and resharpen the bit during excavation use.

  20. High frame rate CCD camera with fast optical shutter

    Energy Technology Data Exchange (ETDEWEB)

    Yates, G.J.; McDonald, T.E. Jr. [Los Alamos National Lab., NM (United States); Turko, B.T. [Lawrence Berkeley National Lab., CA (United States)

    1998-09-01

    A high frame rate CCD camera coupled with a fast optical shutter has been designed for high repetition rate imaging applications. The design uses state-of-the-art microchannel plate image intensifier (MCPII) technology fostered/developed by Los Alamos National Laboratory to support nuclear, military, and medical research requiring high-speed imagery. Key design features include asynchronous resetting of the camera to acquire random transient images, patented real-time analog signal processing with 10-bit digitization at 40--75 MHz pixel rates, synchronized shutter exposures as short as 200pS, sustained continuous readout of 512 x 512 pixels per frame at 1--5Hz rates via parallel multiport (16-port CCD) data transfer. Salient characterization/performance test data for the prototype camera are presented, temporally and spatially resolved images obtained from range-gated LADAR field testing are included, an alternative system configuration using several cameras sequenced to deliver discrete numbers of consecutive frames at effective burst rates up to 5GHz (accomplished by time-phasing of consecutive MCPII shutter gates without overlap) is discussed. Potential applications including dynamic radiography and optical correlation will be presented.

  1. 一种14位高速DAC的电路设计%Design of a High Speed 14-bit DAC Circuit

    Institute of Scientific and Technical Information of China (English)

    唐玉兰; 陈建慧

    2012-01-01

    设计了一个14位电流定标数模转换器,采用4+4+6分段译码电流舵结构.高4位与中间4位采用温度计编码控制,低6位采用直接控制二进制加权电流源,提高了DAC的动态特性。给出了DAC的核心模块的详细设计,包括高精度可编程基准电流源,DAC编解码电路,电流源阵列。采用SMIC0.18urn1P6M设计,CMOS工艺实现。Hspice仿真测试结果表明,在400MHz工作频率下,输出信号为80MHz时,无杂散动态范围为72.47dB,设计满足要求。%Presented in this paper is a 14-bit current scaling DAC, which employs 4+4+6 segmented current- steering architecture. The high 4 bit and intermediate 4 bit adopt thermometer code control, and the low 6 bit uses direct control of binary weighted current source, so the dynamic performance of DAC is improved. The de- tailed design of the core modules of DAC is also presented, including high-precision programmable reference current source, DAC encoding and decoding circuit, and the current source array. The DAC is fabricated in SMIC 0.18urn IP6M with CMOS technology.The Hspice simulation results show that when working frequency is at 400MHz, when output signal is at 80MHz, and when spurious free dynamic range is 72.47 dB, the design will meet the requirements.

  2. Code Division Multiplexing Using AI Based Custom Constellation Scheme - Efficient Modulation for High Data rate Transmission

    Directory of Open Access Journals (Sweden)

    K.SESHADRI SASTRY,

    2010-06-01

    Full Text Available To achieve high bit rate in transmission over wireless channels frequency reuse is an encouraging concept . Rather than dividing allocated frequency spectrum into narrow band width channels , one for each user information is transmitted over a very wide frequency spectrum using the same carrier frequency within same frequency band . In this paper we propose code division multiplexing scheme in which Custom QAM modulator itself is used as code . The propose system is simulated and tested in Matlab 7.4.

  3. Robust Frequency Hopping for High Data Rate Tactical Communications

    Science.gov (United States)

    2006-12-01

    Filter Insert Pilot Channel, h(τ;t) AWGN Jamming Models. J(t) Demod Q Parallel subbands to Serial bit stream Demod EQU EQU Channel...results remains fixed at 5MHz, such that the subband bandwidths are defined as x (5 / )Q MHz Q ; this ensures that the data rate of the system is

  4. Performance Analysis of Ultra Wideband Receivers for High Data Rate Wireless Personal Area Network System

    Directory of Open Access Journals (Sweden)

    Bikramaditya Das

    2010-03-01

    Full Text Available For high data rate ultra wideband communication system, performance comparison of Rake, MMSE andRake-MMSE receivers is attempted in this paper. Further a detail study on Rake-MMSE time domainequalizers is carried out taking into account all the important parameters such as the effect of the numberof Rake fingers and equalizer taps on the error rate performance. This receiver combats inter-symbolinterference by taking advantages of both the Rake and equalizer structure. The bit error rateperformances are investigated using MATLAB simulation on IEEE 802.15.3a defined UWB channelmodels. Simulation results show that the bit error rate probability of Rake-MMSE receiver is much betterthan Rake receiver and MMSE equalizer. Study on non-line of sight indoor channel models illustratesthat bit error rate performance of Rake-MMSE (both LE and DFE improves for CM3 model with smallerspread compared to CM4 channel model. It is indicated that for a MMSE equalizer operating at low tomedium SNR values, the number of Rake fingers is the dominant factor to improve system performance,while at high SNR values the number of equalizer taps plays a more significant role in reducing the errorrate.

  5. Autism's 'Worryingly' High Suicide Rates Spur Conference

    Science.gov (United States)

    ... page: https://medlineplus.gov/news/fullstory_165946.html Autism's 'Worryingly' High Suicide Rates Spur Conference Signs of ... News) -- High rates of suicide among people with autism are drawing specialists to a conference this week ...

  6. Performance Analysis of Ultra Wideband Receivers for High Data Rate Wireless Personal Area Network System

    CERN Document Server

    Das, Bikramaditya; 10.5121/jgraphhoc.2010.2104

    2010-01-01

    For high data rate ultra wideband communication system, performance comparison of Rake, MMSE and Rake-MMSE receivers is attempted in this paper. Further a detail study on Rake-MMSE time domain equalizers is carried out taking into account all the important parameters such as the effect of the number of Rake fingers and equalizer taps on the error rate performance. This receiver combats inter-symbol interference by taking advantages of both the Rake and equalizer structure. The bit error rate performances are investigated using MATLAB simulation on IEEE 802.15.3a defined UWB channel models. Simulation results show that the bit error rate probability of Rake-MMSE receiver is much better than Rake receiver and MMSE equalizer. Study on non-line of sight indoor channel models illustrates that bit error rate performance of Rake-MMSE (both LE and DFE) improves for CM3 model with smaller spread compared to CM4 channel model. It is indicated that for a MMSE equalizer operating at low to medium SNR values, the number o...

  7. Bit Loading Algorithms for Cooperative OFDM Systems

    Directory of Open Access Journals (Sweden)

    Bo Gui

    2007-12-01

    Full Text Available We investigate the resource allocation problem for an OFDM cooperative network with a single source-destination pair and multiple relays. Assuming knowledge of the instantaneous channel gains for all links in the entire network, we propose several bit and power allocation schemes aiming at minimizing the total transmission power under a target rate constraint. First, an optimal and efficient bit loading algorithm is proposed when the relay node uses the same subchannel to relay the information transmitted by the source node. To further improve the performance gain, subchannel permutation, in which the subchannels are reallocated at relay nodes, is considered. An optimal subchannel permutation algorithm is first proposed and then an efficient suboptimal algorithm is considered to achieve a better complexity-performance tradeoff. A distributed bit loading algorithm is also proposed for ad hoc networks. Simulation results show that significant performance gains can be achieved by the proposed bit loading algorithms, especially when subchannel permutation is employed.

  8. Bit Loading Algorithms for Cooperative OFDM Systems

    Directory of Open Access Journals (Sweden)

    Gui Bo

    2008-01-01

    Full Text Available Abstract We investigate the resource allocation problem for an OFDM cooperative network with a single source-destination pair and multiple relays. Assuming knowledge of the instantaneous channel gains for all links in the entire network, we propose several bit and power allocation schemes aiming at minimizing the total transmission power under a target rate constraint. First, an optimal and efficient bit loading algorithm is proposed when the relay node uses the same subchannel to relay the information transmitted by the source node. To further improve the performance gain, subchannel permutation, in which the subchannels are reallocated at relay nodes, is considered. An optimal subchannel permutation algorithm is first proposed and then an efficient suboptimal algorithm is considered to achieve a better complexity-performance tradeoff. A distributed bit loading algorithm is also proposed for ad hoc networks. Simulation results show that significant performance gains can be achieved by the proposed bit loading algorithms, especially when subchannel permutation is employed.

  9. 24-Hour Relativistic Bit Commitment

    Science.gov (United States)

    Verbanis, Ephanielle; Martin, Anthony; Houlmann, Raphaël; Boso, Gianluca; Bussières, Félix; Zbinden, Hugo

    2016-09-01

    Bit commitment is a fundamental cryptographic primitive in which a party wishes to commit a secret bit to another party. Perfect security between mistrustful parties is unfortunately impossible to achieve through the asynchronous exchange of classical and quantum messages. Perfect security can nonetheless be achieved if each party splits into two agents exchanging classical information at times and locations satisfying strict relativistic constraints. A relativistic multiround protocol to achieve this was previously proposed and used to implement a 2-millisecond commitment time. Much longer durations were initially thought to be insecure, but recent theoretical progress showed that this is not so. In this Letter, we report on the implementation of a 24-hour bit commitment solely based on timed high-speed optical communication and fast data processing, with all agents located within the city of Geneva. This duration is more than 6 orders of magnitude longer than before, and we argue that it could be extended to one year and allow much more flexibility on the locations of the agents. Our implementation offers a practical and viable solution for use in applications such as digital signatures, secure voting and honesty-preserving auctions.

  10. FastBit: Interactively Searching Massive Data

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Kesheng; Ahern, Sean; Bethel, E. Wes; Chen, Jacqueline; Childs, Hank; Cormier-Michel, Estelle; Geddes, Cameron; Gu, Junmin; Hagen, Hans; Hamann, Bernd; Koegler, Wendy; Lauret, Jerome; Meredith, Jeremy; Messmer, Peter; Otoo, Ekow; Perevoztchikov, Victor; Poskanzer, Arthur; Prabhat,; Rubel, Oliver; Shoshani, Arie; Sim, Alexander; Stockinger, Kurt; Weber, Gunther; Zhang, Wei-Ming

    2009-06-23

    As scientific instruments and computer simulations produce more and more data, the task of locating the essential information to gain insight becomes increasingly difficult. FastBit is an efficient software tool to address this challenge. In this article, we present a summary of the key underlying technologies, namely bitmap compression, encoding, and binning. Together these techniques enable FastBit to answer structured (SQL) queries orders of magnitude faster than popular database systems. To illustrate how FastBit is used in applications, we present three examples involving a high-energy physics experiment, a combustion simulation, and an accelerator simulation. In each case, FastBit significantly reduces the response time and enables interactive exploration on terabytes of data.

  11. Field application of a fully rotating point-the-bit rotary steerable system (SPE 67716)

    Energy Technology Data Exchange (ETDEWEB)

    Schaaf, S.; Pafitis, D. [Schlumberger Canada Ltd., Calgary, AB (Canada)

    2001-07-01

    Petroleum offshore operations can encounter downhole sliding problems related to maintaining drilling bit orientation, low effective ROP, poor hole cleaning and the inability of the bit to slide. Other problems include differential sticking, buckling, lock-up, high tortuosity, and build-up rate formation sensitive. Several illustrations were presented indicating ways to correct problems with the bit system through better steerability and orientation of the motors. Specifications and field test examples were presented. One of the test examples involved a land operation in California and another involved a vertical well in a strongly dipping formation. The success of the field tests proved the steering concept of an internally off-set drive-shaft. The point-the-bit rotary steerable system contains no stationary components in contact with the formation. In addition, the tool can be drilled at a tangent to the formation. The tests demonstrated that the system is reliable in experimental design. tabs., figs.

  12. W频段卫星通信中正交频分复用技术的误码性能分析%Bit error rate analysis of orthogonal frequency division multiplexing technology in W-band satellite communication

    Institute of Scientific and Technical Information of China (English)

    赵乐; 宋爱民; 刘剑; 薛斌; 郭兴阳

    2015-01-01

    针对传统的卫星通信频段( C频段、Ku频段、Ka频段)应用逐渐趋于饱和的问题,研究了更高的W频段卫星通信。该频段带宽更宽,可以支持更高的数据传输速率,同等条件下天线尺寸更小并可获得更大的天线增益。正交频分复用技术具有很高的频带利用率,适合于高速数据传输,在W频段具有很好的应用前景。参照“IKNOW”项目中的链路预算,采用固态功放的Rapp模型,对OFDM技术应用在W频段卫星通信中的误码性能进行了仿真分析。仿真结果表明:在考虑功放非线性时,存在一个最佳的输入功率补偿点,使OFDM系统的误码率最低,并且发射功率越高,最佳补偿点对应的误码率越低。%Since traditional band applications ( C-band, Ku-band, Ka-band) for satellite communication will gradually tend to be saturated, the higher W-band was studied. W-band has a wider bandwidth, supports a higher data rate, acquires a smaller equipment size and a bigger antenna gain under the same conditions. Orthogonal Frequency Division Multiplexing ( OFDM) technology has a high spectrum efficiency, which makes it be suitable for high data rate transmission, so it has a good application prospect in W-band. Referring to the link budget of “IKNOW” project and using the Rapp model of solid-state power amplifier, the Bit Error Rate ( BER) of OFDM in W-band was simulated and analyzed. The simulation results show that there is a best input power backoff point which makes the BER be lowest when the nonlinear power amplifier is taken in account, and the higher the transmission power is, the lower the BER of the best input power backoff point will be.

  13. High-Speed 32-Bit Tree-Structured Carry Lookahead Adder Using Modified ANT Logic%基于修正ANT逻辑高速树形32 Bit Carry Lookahead加法器

    Institute of Scientific and Technical Information of China (English)

    吴艳; 罗岚

    2006-01-01

    一种用修正全NMOS管逻辑(ANT)实现的树形结构高速32 bit carry Lookahead加法器,使用两相时钟动态CMOS逻辑、修正不反向ANT逻辑和二进制树形结构实现.该加法器运用0.25 μm工艺,文中给出了修正ANT逻辑中所有晶体管的宽长尺寸和仿真结果,最高工作频率为2 GHz,计算结果在3.5个时钟周期后有效.

  14. Shengli Diamond Bits

    Institute of Scientific and Technical Information of China (English)

    Yang Yukun; Han Tao

    1995-01-01

    @@ The geologic condition of Shengli Oilfield (SLOF)is complicated and the range of the rock drillability is wide. For more than 20 years,Shengli Drilling Technology Research Institute, in view of the formation conditions of SLOF,has done a lot of effort and obtained many achivements in design,manufacturing technology and field service. Up to now ,the institute has developed several ten kinds of diamond bits applicable for drilling and coring in formations from extremely soft to hard.

  15. 无线传感器网络中比特错误率估计方法%Differentia-based bit error rate estimation method in wireless sensor network

    Institute of Scientific and Technical Information of China (English)

    裴祥喜; 崔炳德; 李珉; 周志敏

    2014-01-01

    The performance of interference detection in wireless sensor network depends on the performance of bit error rate (BER) estimation, however, the existed BER estimation methods are either too complicate to imple-ment or with low precision. To solve the problem, differentia error estimation (DEE) method is proposed to enhance the precision of BER. The main idea is to insert multi-level error estimation bits that with different error estimation ability, which are random and uniformly distributed, into the sender’s packets. And the receivers estimate the BER by using the relation between the BER and parity check. Meanwhile, DEE optimizes the ability of error estimation bit of each level by making use of BER’s feature of non-uniform distribution, to enhance the estimate precision of BER with higher probability and lower the average estimation error. The experiments shows that, compared with the error estimating coding (EEC) method, the average estimation error decreases 44%, and the estimation error decreas-es as much as 68%when the redundancy is decreased.%由于无线传感器网络中干扰检测的性能依赖于比特错误率(Bit Error Rate, BER)估计的准确性,而现有的比特错误率估计方法或者难以实现,或者准确性差。针对这个问题,本文提出了采用差异化思想来提高比特错误率估计准确度的方法DEE(Differentiated Error Estimation)。其主要是发送方在数据包中插入具有不同估错能力的多级估错位,并随机均匀地分布所有估错位。接收方借助BER与奇偶校验失败概率的理论关系来估计BER。同时,DEE利用BER非均匀分布特征来优化各级估错位的能力,提高出现概率高的BER的估计准确度,以降低平均估计误差。实验结果表明,与现有方法EEC相比,DEE可将估计误差平均减少约44%。当估错冗余较低时,DEE可将估计误差减少约68%。

  16. Understanding High Rate Behavior Through Low Rate Analog

    Science.gov (United States)

    2014-04-28

    Dioh, N.N., et al., The High-Strain Rate Behavior of Polymers. Journal De Physique Iv, 1994. 4(C8): p. 119-124. 21. Dioh, N.N., P.S. Leevers, and J.G...constitutive response of polymeric materials as a function of temperature and strain rate. Journal De Physique Iv, 2003. 110: p. 27-32. 23. Brown, E.N...properties of polycarbonate under dynamic loading. Journal De Physique Iv, 2003. 110: p. 159-164. 56. Li, Z.H. and J. Lambros, Strain rate effects on the

  17. Two-Bit Bit Flipping Decoding of LDPC Codes

    CERN Document Server

    Nguyen, Dung Viet; Marcellin, Michael W

    2011-01-01

    In this paper, we propose a new class of bit flipping algorithms for low-density parity-check (LDPC) codes over the binary symmetric channel (BSC). Compared to the regular (parallel or serial) bit flipping algorithms, the proposed algorithms employ one additional bit at a variable node to represent its "strength." The introduction of this additional bit increases the guaranteed error correction capability by a factor of at least 2. An additional bit can also be employed at a check node to capture information which is beneficial to decoding. A framework for failure analysis of the proposed algorithms is described. These algorithms outperform the Gallager A/B algorithm and the min-sum algorithm at much lower complexity. Concatenation of two-bit bit flipping algorithms show a potential to approach the performance of belief propagation (BP) decoding in the error floor region, also at lower complexity.

  18. 100km reach DWDM SuperPON with upstream bit rates of 2.5Gb/s and 10Gb/s

    Science.gov (United States)

    Talli, Giuseppe; Townsend, Paul D.

    2005-06-01

    The potential for sharing infrastructure costs between a large number of customers and the high data rates allowed by optical fibres make passive optical networks (PONs) an attractive solution to the problem of upgrading current copper-based access networks. Optically-amplified, long reach, time division multiple access (TDMA) PONs or 'SuperPONs' offer the potential to further reduce bandwidth transport costs by enabling the direct connection of access networks and inner core networks, thereby eliminating the costs of the outer core/metro backhaul network. The use of dense wavelength division multiplexing (DWDM) could also allow sharing the same feeder fibre and PON head end equipment between a number of such TDMA SuperPONs, each working at different ITU-grid wavelengths. However, a cost effective access solution should employ a customer optical network unit (ONU), which is independent of the PON wavelength, or colorless, in order to reduce the high inventory and deployment costs of using expensive, wavelength-specified sources at the customer. In this paper we demonstrate for the first time the use of a monolithically-integrated, electroabsorption modulator-semiconductor optical amplifiers (EAM-SOAs) as a colorless ONU in a high performance DWDM SuperPON system. These compact devices offer the potential for low-cost optoelectronic integration with other ONU components together with the ability to modulate at rates up to 10Gbps and beyond. We have used this approach to investigate the feasibility of supporting up to 17 SuperPONs from a single feeder fibre and PON head end, each of 100km-reach accommodating 512 users at 2.5Gb/s or 128 at 10Gb/s.

  19. 基于人眼视觉特性的低比特率图像压缩编码%Improved iow bit-rate image coding scheme based on human visual system.

    Institute of Scientific and Technical Information of China (English)

    王力; 王向阳

    2011-01-01

    为了提高编码速度和改进视觉效果,提出了一种改进的低比特率SPIHT算法.算法首先用提升小波对原始图像进行分解,再结合人眼视觉掩蔽特性,对不同区域内图像信息所对应的小波系数赋予不同视觉权值,以保证优先传输视觉上的最重要系数,最后根据系数重要性,对低频系数采用新的排列结构,并采用SPIHT编码思想完成图像压缩.实验结果表明,该算法压缩效果优于SPIHT图像压缩方案,特别在低比特率下.%A improved low bit-rate image coding scheme is presented. The lifting wavelet transform is applied to the original image,and the visual gains are achieved by exploiting Human Visual System(HVS) characteristics to weigh wavelet coefficients according to their perceptual importance. Lastly, the lower frequency exploits a new partitioning structure based on the importance of coefficients.The experimental results showthat the modified image compression scheme provides higher perceptual quality and higher PSNR than SPIHT,especially at low bit rates.

  20. Low Complexity Encoder of High Rate Irregular QC-LDPC Codes for Partial Response Channels

    Directory of Open Access Journals (Sweden)

    IMTAWIL, V.

    2011-11-01

    Full Text Available High rate irregular QC-LDPC codes based on circulant permutation matrices, for efficient encoder implementation, are proposed in this article. The structure of the code is an approximate lower triangular matrix. In addition, we present two novel efficient encoding techniques for generating redundant bits. The complexity of the encoder implementation depends on the number of parity bits of the code for the one-stage encoding and the length of the code for the two-stage encoding. The advantage of both encoding techniques is that few XOR-gates are used in the encoder implementation. Simulation results on partial response channels also show that the BER performance of the proposed code has gain over other QC-LDPC codes.

  1. Evaluation of Bit Preservation Strategies

    DEFF Research Database (Denmark)

    Zierau, Eld; Kejser, Ulla Bøgvad; Kulovits, Hannes

    2010-01-01

    This article describes a methodology which supports evaluation of bit preservation strategies for different digital materials. This includes evaluation of alternative bit preservation solution. The methodology presented uses the preservation planning tool Plato for evaluations, and a BR......-ReMS prototype to calculate measures for how well bit preservation requirements are met. Planning storage of data as part of preservation planning involves classification of data with regard to requirements on confidentiality, bit safety, available and costs. Choice of storage with such parameters is quite...... complex since e.g. more copies of data means better bit safety, but higher cost and bigger risk of breaking confidentiality. Based on a case of a bit repository offering varied bit preservation solutions, the article will present results of using the methodology to make plans and choices of alternatives...

  2. Dynamics of coupled simplest chaotic two-component electronic circuits and its potential application to random bit generation

    Energy Technology Data Exchange (ETDEWEB)

    Modeste Nguimdo, Romain, E-mail: Romain.Nguimdo@vub.ac.be [Applied Physics Research Group, APHY, Vrije Universiteit Brussel, Pleinlaan 2, B-1050 Brussel (Belgium); Tchitnga, Robert [Laboratory of Electronics, Automation and Signal Processing, Department of Physics, University of Dschang, P.O. Box 67, Dschang (Cameroon); Woafo, Paul [Laboratory of Modelling and Simulation in Engineering and Biological Physics, Faculty of Science, University of Yaoundé I, P.O. Box 812, Yaoundé (Cameroon)

    2013-12-15

    We numerically investigate the possibility of using a coupling to increase the complexity in simplest chaotic two-component electronic circuits operating at high frequency. We subsequently show that complex behaviors generated in such coupled systems, together with the post-processing are suitable for generating bit-streams which pass all the NIST tests for randomness. The electronic circuit is built up by unidirectionally coupling three two-component (one active and one passive) oscillators in a ring configuration through resistances. It turns out that, with such a coupling, high chaotic signals can be obtained. By extracting points at fixed interval of 10 ns (corresponding to a bit rate of 100 Mb/s) on such chaotic signals, each point being simultaneously converted in 16-bits (or 8-bits), we find that the binary sequence constructed by including the 10(or 2) least significant bits pass statistical tests of randomness, meaning that bit-streams with random properties can be achieved with an overall bit rate up to 10×100 Mb/s =1Gbit/s (or 2×100 Mb/s =200 Megabit/s). Moreover, by varying the bias voltages, we also investigate the parameter range for which more complex signals can be obtained. Besides being simple to implement, the two-component electronic circuit setup is very cheap as compared to optical and electro-optical systems.

  3. Positional information, in bits.

    Science.gov (United States)

    Dubuis, Julien O; Tkacik, Gasper; Wieschaus, Eric F; Gregor, Thomas; Bialek, William

    2013-10-08

    Cells in a developing embryo have no direct way of "measuring" their physical position. Through a variety of processes, however, the expression levels of multiple genes come to be correlated with position, and these expression levels thus form a code for "positional information." We show how to measure this information, in bits, using the gap genes in the Drosophila embryo as an example. Individual genes carry nearly two bits of information, twice as much as would be expected if the expression patterns consisted only of on/off domains separated by sharp boundaries. Taken together, four gap genes carry enough information to define a cell's location with an error bar of ~1 along the anterior/posterior axis of the embryo. This precision is nearly enough for each cell to have a unique identity, which is the maximum information the system can use, and is nearly constant along the length of the embryo. We argue that this constancy is a signature of optimality in the transmission of information from primary morphogen inputs to the output of the gap gene network.

  4. Robust relativistic bit commitment

    Science.gov (United States)

    Chakraborty, Kaushik; Chailloux, André; Leverrier, Anthony

    2016-12-01

    Relativistic cryptography exploits the fact that no information can travel faster than the speed of light in order to obtain security guarantees that cannot be achieved from the laws of quantum mechanics alone. Recently, Lunghi et al. [Phys. Rev. Lett. 115, 030502 (2015), 10.1103/PhysRevLett.115.030502] presented a bit-commitment scheme where each party uses two agents that exchange classical information in a synchronized fashion, and that is both hiding and binding. A caveat is that the commitment time is intrinsically limited by the spatial configuration of the players, and increasing this time requires the agents to exchange messages during the whole duration of the protocol. While such a solution remains computationally attractive, its practicality is severely limited in realistic settings since all communication must remain perfectly synchronized at all times. In this work, we introduce a robust protocol for relativistic bit commitment that tolerates failures of the classical communication network. This is done by adding a third agent to both parties. Our scheme provides a quadratic improvement in terms of expected sustain time compared with the original protocol, while retaining the same level of security.

  5. 基于压缩感知的低速率语音编码新方案%New low bit rate speech coding scheme based on compressed sensing

    Institute of Scientific and Technical Information of China (English)

    叶蕾; 杨震; 孙林慧

    2011-01-01

    利用语音小波高频系数的稀疏性和压缩感知原理,提出一种新的基于压缩感知的低速率语音编码方案,其中小波高频系数的压缩感知重构分别采用l1范数优化方案及码本预测方案进行,前者对大幅度样值重构效果较好,且不仅适用于语音,也适用于音乐信号,具有传统的线性预测编码方法无法比拟的优势,后者对稀疏系数位置的估计较好,且不需要采用压缩感知重构常用的基追踪算法或匹配追踪算法,从而减少了计算量.两种方法的联合使用能发挥各自的优势,使得重构语音的音质进一步改善.%Utilizing the sparsity of high frequency wavelet transform coefficients of speech signal and theory of compressed sensing, a new low bit rate speech coding scheme based on compressed sensing is proposed. The reconstruction of high frequency wavelet transform coefficients is achieved by l1 normal optimization and codebook prediction reconstruction respectively. L1 reconstruction has good effect for large coefficients and suits for both speech and music, with which traditional linear prediction coding cannot compare. Codebook prediction reconstruction has good effect for the location of sparse coefficients and reduces the amount of calculation due to not using basis pursuit or matching pursuit. The combination of these two reconstruction methods can bring the advantages of both methods and improve the quality of the reconstructed speech.

  6. Bit-padding information guided channel hopping

    KAUST Repository

    Yang, Yuli

    2011-02-01

    In the context of multiple-input multiple-output (MIMO) communications, we propose a bit-padding information guided channel hopping (BP-IGCH) scheme which breaks the limitation that the number of transmit antennas has to be a power of two based on the IGCH concept. The proposed scheme prescribes different bit-lengths to be mapped onto the indices of the transmit antennas and then uses padding technique to avoid error propagation. Numerical results and comparisons, on both the capacity and the bit error rate performances, are provided and show the advantage of the proposed scheme. The BP-IGCH scheme not only offers lower complexity to realize the design flexibility, but also achieves better performance. © 2011 IEEE.

  7. Stability of single skyrmionic bits

    Science.gov (United States)

    Vedmedenko, Olena; Hagemeister, Julian; Romming, Niklas; von Bergmann, Kirsten; Wiesendanger, Roland

    The switching between topologically distinct skyrmionic and ferromagnetic states has been proposed as a bit operation for information storage. While long lifetimes of the bits are required for data storage devices, the lifetimes of skyrmions have not been addressed so far. Here we show by means of atomistic Monte Carlo simulations that the field-dependent mean lifetimes of the skyrmionic and ferromagnetic states have a high asymmetry with respect to the critical magnetic field, at which these lifetimes are identical. According to our calculations, the main reason for the enhanced stability of skyrmions is a different field dependence of skyrmionic and ferromagnetic activation energies and a lower attempt frequency of skyrmions rather than the height of energy barriers. We use this knowledge to propose a procedure for the determination of effective material parameters and the quantification of the Monte Carlo timescale from the comparison of theoretical and experimental data. Financial support from the DFG in the framework of the SFB668 is acknowledged.

  8. High burn rate solid composite propellants

    Science.gov (United States)

    Manship, Timothy D.

    High burn rate propellants help maintain high levels of thrust without requiring complex, high surface area grain geometries. Utilizing high burn rate propellants allows for simplified grain geometries that not only make production of the grains easier, but the simplified grains tend to have better mechanical strength, which is important in missiles undergoing high-g accelerations. Additionally, high burn rate propellants allow for a higher volumetric loading which reduces the overall missile's size and weight. The purpose of this study is to present methods of achieving a high burn rate propellant and to develop a composite propellant formulation that burns at 1.5 inches per second at 1000 psia. In this study, several means of achieving a high burn rate propellant were presented. In addition, several candidate approaches were evaluated using the Kepner-Tregoe method with hydroxyl terminated polybutadiene (HTPB)-based propellants using burn rate modifiers and dicyclopentadiene (DCPD)-based propellants being selected for further evaluation. Propellants with varying levels of nano-aluminum, nano-iron oxide, FeBTA, and overall solids loading were produced using the HTPB binder and evaluated in order to determine the effect the various ingredients have on the burn rate and to find a formulation that provides the burn rate desired. Experiments were conducted to compare the burn rates of propellants using the binders HTPB and DCPD. The DCPD formulation matched that of the baseline HTPB mix. Finally, GAP-plasticized DCPD gumstock dogbones were attempted to be made for mechanical evaluation. Results from the study show that nano-additives have a substantial effect on propellant burn rate with nano-iron oxide having the largest influence. Of the formulations tested, the highest burn rate was a 84% solids loading mix using nano-aluminum nano-iron oxide, and ammonium perchlorate in a 3:1(20 micron: 200 micron) ratio which achieved a burn rate of 1.2 inches per second at 1000

  9. Quantifying the Impact of Single Bit Flips on Floating Point Arithmetic

    Energy Technology Data Exchange (ETDEWEB)

    Elliott, James J [ORNL; Mueller, Frank [North Carolina State University; Stoyanov, Miroslav K [ORNL; Webster, Clayton G [ORNL

    2013-08-01

    In high-end computing, the collective surface area, smaller fabrication sizes, and increasing density of components have led to an increase in the number of observed bit flips. If mechanisms are not in place to detect them, such flips produce silent errors, i.e. the code returns a result that deviates from the desired solution by more than the allowed tolerance and the discrepancy cannot be distinguished from the standard numerical error associated with the algorithm. These phenomena are believed to occur more frequently in DRAM, but logic gates, arithmetic units, and other circuits are also susceptible to bit flips. Previous work has focused on algorithmic techniques for detecting and correcting bit flips in specific data structures, however, they suffer from lack of generality and often times cannot be implemented in heterogeneous computing environment. Our work takes a novel approach to this problem. We focus on quantifying the impact of a single bit flip on specific floating-point operations. We analyze the error induced by flipping specific bits in the most widely used IEEE floating-point representation in an architecture-agnostic manner, i.e., without requiring proprietary information such as bit flip rates and the vendor-specific circuit designs. We initially study dot products of vectors and demonstrate that not all bit flips create a large error and, more importantly, expected value of the relative magnitude of the error is very sensitive on the bit pattern of the binary representation of the exponent, which strongly depends on scaling. Our results are derived analytically and then verified experimentally with Monte Carlo sampling of random vectors. Furthermore, we consider the natural resilience properties of solvers based on the fixed point iteration and we demonstrate how the resilience of the Jacobi method for linear equations can be significantly improved by rescaling the associated matrix.

  10. High frame rate synthetic aperture duplex imaging

    DEFF Research Database (Denmark)

    Stuart, Matthias Bo; Tomov, Borislav Gueorguiev; Pihl, Michael Johannes

    2013-01-01

    aperture flow imaging as demonstrated in this paper. Synthetic aperture, directional beamforming, and cross-correlation are used to produce B-mode and vector velocity images at high frame rates. The frame rate equals the effective pulse repetition frequency of each imaging mode. Emissions for making the B...

  11. High-Rate Receiver Design Project

    Data.gov (United States)

    National Aeronautics and Space Administration — We propose an initial architectural and preliminary hardware design study for a high-rate receiver capable of decoding modulation suites specified by CCSDS 413.0-G-1...

  12. Evaluation of Bit Preservation Strategies

    DEFF Research Database (Denmark)

    Zierau, Eld; Kejser, Ulla Bøgvad; Kulovits, Hannes

    2010-01-01

    This article describes a methodology which supports evaluation of bit preservation strategies for different digital materials. This includes evaluation of alternative bit preservation solution. The methodology presented uses the preservation planning tool Plato for evaluations, and a BR...... for different digital material with different requirements for bit integrity and confidentiality. This case shows that the methodology, including the tools used, is useful for this purpose....

  13. ASIC for High Rate 3D Position Sensitive Detectors

    Energy Technology Data Exchange (ETDEWEB)

    Vernon, E.; De Geronimo, G.; Ackley, K.; Fried, J.; He, Z.; Herman, C.; Zhang, F.

    2010-06-16

    We report on the development of an application specific integrated circuit (ASIC) for 3D position sensitive detectors (3D PSD). The ASIC is designed to operate with pixelated wide bandgap sensors like Cadmium-Zinc-Telluride (CZT), Mercuric Iodide (Hgl2) and Thallium Bromide (TIBr). It measures the amplitudes and timings associated with an ionizing event on 128 anodes, the anode grid, and the cathode. Each channel provides low-noise charge amplification, high-order shaping with peaking time adjustable from 250 ns to 12 {micro}s, gain adjustable to 20 mV/fC or 120 mV/fC (for a dynamic range of 3.2 MeV and 530 keV in CZT), amplitude discrimination with 5-bit trimming, and positive and negative peak and timing detections. The readout can be full or sparse, based on a flag and single- or multi-cycle token passing. All channels, triggered channels only, or triggered with neighbors can be read out thus increasing the rate capability of the system to more than 10 kcps. The ASIC dissipates 330 mW which corresponds to about 2.5 mW per channel.

  14. Dependence of the bit error rate on the signal power and length of a single-channel coherent single-span communication line (100 Gbit s-1) with polarisation division multiplexing

    Science.gov (United States)

    Gurkin, N. V.; Konyshev, V. A.; Nanii, O. E.; Novikov, A. G.; Treshchikov, V. N.; Ubaydullaev, R. R.

    2015-01-01

    We have studied experimentally and using numerical simulations and a phenomenological analytical model the dependences of the bit error rate (BER) on the signal power and length of a coherent single-span communication line with transponders employing polarisation division multiplexing and four-level phase modulation (100 Gbit s-1 DP-QPSK format). In comparing the data of the experiment, numerical simulations and theoretical analysis, we have found two optimal powers: the power at which the BER is minimal and the power at which the fade margin in the line is maximal. We have derived and analysed the dependences of the BER on the optical signal power at the fibre line input and the dependence of the admissible input signal power range for implementation of the communication lines with a length from 30 - 50 km up to a maximum length of 250 km.

  15. Methods to ensure optimal off-bottom and drill bit distance under pellet impact drilling

    Science.gov (United States)

    Kovalyov, A. V.; Isaev, Ye D.; Vagapov, A. R.; Urnish, V. V.; Ulyanova, O. S.

    2016-09-01

    The paper describes pellet impact drilling which could be used to increase the drilling speed and the rate of penetration when drilling hard rock for various purposes. Pellet impact drilling implies rock destruction by metal pellets with high kinetic energy in the immediate vicinity of the earth formation encountered. The pellets are circulated in the bottom hole by a high velocity fluid jet, which is the principle component of the ejector pellet impact drill bit. The paper presents the survey of methods ensuring an optimal off-bottom and a drill bit distance. The analysis of methods shows that the issue is topical and requires further research.

  16. PDC (polycrystalline diamond compact) bit research at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Finger, J.T.; Glowka, D.A.

    1989-06-01

    From the beginning of the geothermal development program, Sandia has performed and supported research into polycrystalline diamond compact (PDC) bits. These bits are attractive because they are intrinsically efficient in their cutting action (shearing, rather than crushing) and they have no moving parts (eliminating the problems of high-temperature lubricants, bearings, and seals.) This report is a summary description of the analytical and experimental work done by Sandia and our contractors. It describes analysis and laboratory tests of individual cutters and complete bits, as well as full-scale field tests of prototype and commercial bits. The report includes a bibliography of documents giving more detailed information on these topics. 26 refs.

  17. Pulse shaping for all-optical signal processing of ultra-high bit rate serial data signals

    DEFF Research Database (Denmark)

    Palushani, Evarist

    demultiplexing experiments. The frequency-to-time technique was deployed also for implementing an alloptical synchronizer and re-timer. By using the specular phenomenon, time-to-frequency OFT, it was possible to develop a novel scheme for serial-to-parallel conversion, implemented via four-wave mixing (FWM...

  18. Hey! A Tarantula Bit Me!

    Science.gov (United States)

    ... it or try to play with it. These spiders will not bite you unless they feel threatened — if you leave them alone, they will leave you alone. For Teens For ... Stung Me! Hey! A Scorpion Stung Me! Hey! A Black Widow Spider Bit Me! Hey! A Brown Recluse Spider Bit ...

  19. Understanding High Saving Rate in China

    Institute of Scientific and Technical Information of China (English)

    Xinhua He; Yongfu Cao

    2007-01-01

    This paper presents a detailed analysis of the Chinese saving rate based on the flow of funds data. It finds that the most widely adopted view of precautionary saving, which is regarded as the top reason for maintaining a high saving rate in China, is misleading because this conclusion is drawn from the household survey data. In fact, the household saving rate has declined dramatically since the mid-1990s, as is observed from the flow of funds framework.The high national saving rate is attributed to the increasing shares of both government and corporation disposable incomes. Insufficient consumption demand is caused by the persistent decrease in percentage share of household to national disposable income. Governmentdirected income redistribution urgently needs to be improved to accelerate consumption,which in turn would make the Chinese economy less investment-led and help to reduce the current account surplus.

  20. Experimental unconditionally secure bit commitment

    Science.gov (United States)

    Liu, Yang; Cao, Yuan; Curty, Marcos; Liao, Sheng-Kai; Wang, Jian; Cui, Ke; Li, Yu-Huai; Lin, Ze-Hong; Sun, Qi-Chao; Li, Dong-Dong; Zhang, Hong-Fei; Zhao, Yong; Chen, Teng-Yun; Peng, Cheng-Zhi; Zhang, Qiang; Cabello, Adan; Pan, Jian-Wei

    2014-03-01

    Quantum physics allows unconditionally secure communication between parties that trust each other. However, when they do not trust each other such as in the bit commitment, quantum physics is not enough to guarantee security. Only when relativistic causality constraints combined, the unconditional secure bit commitment becomes feasible. Here we experimentally implement a quantum bit commitment with relativistic constraints that offers unconditional security. The commitment is made through quantum measurements in two quantum key distribution systems in which the results are transmitted via free-space optical communication to two agents separated with more than 20 km. Bits are successfully committed with less than 5 . 68 ×10-2 cheating probability. This provides an experimental proof of unconditional secure bit commitment and demonstrates the feasibility of relativistic quantum communication.

  1. A high-strain-rate superplastic ceramic.

    Science.gov (United States)

    Kim, B N; Hiraga, K; Morita, K; Sakka, Y

    2001-09-20

    High-strain-rate superplasticity describes the ability of a material to sustain large plastic deformation in tension at high strain rates of the order of 10-2 to 10-1 s-1 and is of great technological interest for the shape-forming of engineering materials. High-strain-rate superplasticity has been observed in aluminium-based and magnesium-based alloys. But for ceramic materials, superplastic deformation has been restricted to low strain rates of the order of 10-5 to 10-4 s-1 for most oxides and nitrides with the presence of intergranular cavities leading to premature failure. Here we show that a composite ceramic material consisting of tetragonal zirconium oxide, magnesium aluminate spinel and alpha-alumina phases exhibits superplasticity at strain rates up to 1 s-1. The composite also exhibits a large tensile elongation, exceeding 1,050 per cent for a strain rate of 0.4 s-1. The tensile flow behaviour and deformed microstructure of the material indicate that superplasticity is due to a combination of limited grain growth in the constitutive phases and the intervention of dislocation-induced plasticity in the zirconium oxide phase. We suggest that the present results hold promise for the application of shape-forming technologies to ceramic materials.

  2. Electrorheological Effects at High Shear Rate

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Much attention has been given to electrorheological (ER) fluids because of the ER effect, which has been described by a large number of researchers as a notable increase in the apparent viscosity of a fluid upon the application of an electric field. The description of ER effects is, however, not accurate at high shear rates. To clarify the discrepancy, we analyze and compute the apparent viscosity as a function of shear rate for ER fluid flow between rotating coaxial cylinders in the presence of an electric field. The theoretical predictions show that the increase of electric intensity contributes little to the apparent viscosity enhancement at high shear rates, while ER effects for ER fluids with a higher polarization rate still exist and ER devices possess controllability in this regime. Description of the ER effect by the apparent viscosity leads to an unrealistic conclusion that ER effects disappear at high shear rates, because the apparent viscosity of ER fluids approaches the value for Newtonian fluids. Therefore, it is concluded that the proper description of ER effects, i.e., one that holds uniformly for any strain rate when ER effects exist, is manifested by a remarkable increase in the extra stress rather than in the apparent viscosity of ER fluids.

  3. Experimental study of rock-breaking with an offset single cone bit

    Institute of Scientific and Technical Information of China (English)

    Chen Yinghua

    2008-01-01

    An experimental study of rock-breaking with an offset single cone bit was completed on the bit bench test equipment.Data such as transmission ratio,weight on bit (WOB),rate of penetration (ROP)and torque on bit were acquired in the experiments.Based on analyzing the experimental results,several conclusions were drawn as follows.The transmission ratio of the offset single-cone bit changed slightly with rotary speed of bit,weight on bit and offset distance.The rate of penetration of the offset singlecone bit increased with increase of WOB and offset distance.The torque on bit increased with increase of offset distance under the same WOB and bit rotary speed,decreased with increase of bit rotary speed under the same WOB.The rock-breaking mechanism of the offset single-cone bit was a scraping action.This indicates that the offset single-cone bit is a chipping type bit.

  4. Thrombus Formation at High Shear Rates.

    Science.gov (United States)

    Casa, Lauren D C; Ku, David N

    2017-06-21

    The final common pathway in myocardial infarction and ischemic stroke is occlusion of blood flow from a thrombus forming under high shear rates in arteries. A high-shear thrombus forms rapidly and is distinct from the slow formation of coagulation that occurs in stagnant blood. Thrombosis at high shear rates depends primarily on the long protein von Willebrand factor (vWF) and platelets, with hemodynamics playing an important role in each stage of thrombus formation, including vWF binding, platelet adhesion, platelet activation, and rapid thrombus growth. The prediction of high-shear thrombosis is a major area of biofluid mechanics in which point-of-care testing and computational modeling are promising future directions for clinically relevant research. Further research in this area will enable identification of patients at high risk for arterial thrombosis, improve prevention and treatment based on shear-dependent biological mechanisms, and improve blood-contacting device design to reduce thrombosis risk.

  5. High Strain Rate Characterisation of Composite Materials

    DEFF Research Database (Denmark)

    Eriksen, Rasmus Normann Wilken

    The high strain rate characterisation of FRP materials present the experimenter with a new set of challenges in obtaining valid experimental data. These challenges were addressed in this work with basis in classic wave theory. The stress equilibrium process for linear elastic materials, as fibre...... a linear elastic specimen to reach a state of constant strain rate before fracture. This was in contrast to ductile materials, which are widely tested with for the High-speed servohydraulic test machine. The development of the analysis and the interpretation of the results, were based on the experience...

  6. High Resolution Measurement of the Glycolytic Rate

    Science.gov (United States)

    Bittner, Carla X.; Loaiza, Anitsi; Ruminot, Iván; Larenas, Valeria; Sotelo-Hitschfeld, Tamara; Gutiérrez, Robin; Córdova, Alex; Valdebenito, Rocío; Frommer, Wolf B.; Barros, L. Felipe

    2010-01-01

    The glycolytic rate is sensitive to physiological activity, hormones, stress, aging, and malignant transformation. Standard techniques to measure the glycolytic rate are based on radioactive isotopes, are not able to resolve single cells and have poor temporal resolution, limitations that hamper the study of energy metabolism in the brain and other organs. A new method is described in this article, which makes use of a recently developed FRET glucose nanosensor to measure the rate of glycolysis in single cells with high temporal resolution. Used in cultured astrocytes, the method showed for the first time that glycolysis can be activated within seconds by a combination of glutamate and K+, supporting a role for astrocytes in neurometabolic and neurovascular coupling in the brain. It was also possible to make a direct comparison of metabolism in neurons and astrocytes lying in close proximity, paving the way to a high-resolution characterization of brain energy metabolism. Single-cell glycolytic rates were also measured in fibroblasts, adipocytes, myoblasts, and tumor cells, showing higher rates for undifferentiated cells and significant metabolic heterogeneity within cell types. This method should facilitate the investigation of tissue metabolism at the single-cell level and is readily adaptable for high-throughput analysis. PMID:20890447

  7. High resolution measurement of the glycolytic rate

    Directory of Open Access Journals (Sweden)

    Carla X Bittner

    2010-09-01

    Full Text Available The glycolytic rate is sensitive to physiological activity, hormones, stress, aging and malignant transformation. Standard techniques to measure the glycolytic rate are based on radioactive isotopes, are not able to resolve single cells and have poor temporal resolution, limitations that hamper the study of energy metabolism in the brain and other organs. A new method is described in this article, which makes use of a recently-developed FRET glucose nanosensor to measure the rate of glycolysis in single cells with high temporal resolution. Used in cultured astrocytes, the method showed for the first time that glycolysis can be activated within seconds by a combination of glutamate and K+, supporting a role for astrocytes in neurometabolic and neurovascular coupling in the brain. It was also possible to make a direct comparison of metabolism in neurons and astrocytes lying in close proximity, paving the way to a high-resolution characterization of brain energy metabolism. Single-cell glycolytic rates were also measured in fibroblasts, adipocytes, myoblasts and tumor cells, showing higher rates for undifferentiated cells and significant metabolic heterogeneity within cell types. This method should facilitate the investigation of tissue metabolism at the single-cell level and is readily adaptable for high-throughput analysis.

  8. High rate, high reliability Li/SO2 cells

    Science.gov (United States)

    Chireau, R.

    1982-03-01

    The use of the lithium/sulfur dioxide system for aerospace applications is discussed. The high rate density in the system is compared to some primary systems: mercury zinc, silver zinc, and magnesium oxide. Estimates are provided of the storage life and shelf life of typical lithium sulfur batteries. The design of lithium cells is presented and criteria are given for improving the output of cells in order to achieve high rate and high reliability.

  9. An OFDMA Power Allocation Algorithm Considering Integer Bit Rate and Fairness for Cognitive Radio Networks%考虑整数比特率及公平性的认知无线电OFDMA功率分配算法

    Institute of Scientific and Technical Information of China (English)

    郝万明; 杨守义

    2014-01-01

    For orthogonal frequency division multiple access( OFDMA)-based cognitive radio systems, the transmission rate of every cognitive user must be an integer in practice, and the single cognitive user is on-ly considered in previous rate rounding algorithm. According to this situation, a new rate rounding algo-rithm is proposed in this paper, and it is modified based on the previous algorithm. Every subcarrier rate is adjusted once at most, which ensures the fairness at the rate rounding between cognitive users, and the to-tal bit rate is also improved. The simulation result shows that the fairness among cognitive users is im-proved effectively by the proposed algorithm.%在基于正交频分多址( OFDMA)的认知无线电系统中,每个认知用户在实际中都是以整数比特进行传输,而以往的速率取整算法只考虑了单认知用户。针对这种情况,提出了一种新的速率取整算法,该算法在原有算法的基础上进行了改进,让每个子载波最多参与一次速率的调整,从而使其在应用于多认知用户时保证了速率取整时的公平性,同时总的传输比特率比原算法有了一定的提高。仿真结果表明,所提算法有效提高了各认知用户在速率取整时的公平性。

  10. Reinforcement Learning in BitTorrent Systems

    CERN Document Server

    Izhak-Ratzin, Rafit; van der Schaar, Mihaela

    2010-01-01

    Recent research efforts have shown that the popular BitTorrent protocol does not provide fair resource reciprocation and may allow free-riding. In this paper, we propose a BitTorrent-like protocol that replaces the peer selection mechanisms in the regular BitTorrent protocol with a novel reinforcement learning (RL) based mechanism. Due to the inherent opration of P2P systems, which involves repeated interactions among peers over a long period of time, the peers can efficiently identify free-riders as well as desirable collaborators by learning the behavior of their associated peers. Thus, it can help peers improve their download rates and discourage free-riding, while improving fairness in the system. We model the peers' interactions in the BitTorrent-like network as a repeated interaction game, where we explicitly consider the strategic behavior of the peers. A peer, which applies the RL-based mechanism, uses a partial history of the observations on associated peers' statistical reciprocal behaviors to deter...

  11. High Rate Performing Li-ion Battery

    Science.gov (United States)

    2015-02-09

    permeable to lithium ions and efficient in transferring the electrons into/from the LVP surface to the corresponding current collector. a) b) c) d) e...PO4)3/C for High Rate Lithium-ion Battery Applications”, Lee Hwang Sheng, Nail Suleimanov, Vishwanathan Ramar, Mangayarkarasi Murugan, Kuppan

  12. [Hopes of high dose-rate radiotherapy].

    Science.gov (United States)

    Fouillade, Charles; Favaudon, Vincent; Vozenin, Marie-Catherine; Romeo, Paul-Henri; Bourhis, Jean; Verrelle, Pierre; Devauchelle, Patrick; Patriarca, Annalisa; Heinrich, Sophie; Mazal, Alejandro; Dutreix, Marie

    2017-04-01

    In this review, we present the synthesis of the newly acquired knowledge concerning high dose-rate irradiations and the hopes that these new radiotherapy modalities give rise to. The results were presented at a recent symposium on the subject. Copyright © 2017. Published by Elsevier Masson SAS.

  13. Understanding High School Graduation Rates in Arizona

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  14. Understanding High School Graduation Rates in Delaware

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  15. Understanding High School Graduation Rates in Idaho

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  16. Understanding High School Graduation Rates in Illinois

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  17. Understanding High School Graduation Rates in Massachusetts

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  18. Understanding High School Graduation Rates in Pennsylvania

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  19. Understanding High School Graduation Rates in Minnesota

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  20. Understanding High School Graduation Rates in Kentucky

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  1. Understanding High School Graduation Rates in Maryland

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  2. Understanding High School Graduation Rates in Wisconsin

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  3. Understanding High School Graduation Rates in Wyoming

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  4. Understanding High School Graduation Rates in Alaska

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  5. Understanding High School Graduation Rates in Oklahoma

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  6. Understanding High School Graduation Rates in Tennessee

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  7. Understanding High School Graduation Rates in Georgia

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  8. Understanding High School Graduation Rates in Iowa

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  9. Understanding High School Graduation Rates in Nevada

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  10. Understanding High School Graduation Rates in Texas

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  11. Understanding High School Graduation Rates in Florida

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  12. Understanding High School Graduation Rates in Nebraska

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  13. Understanding High School Graduation Rates in Oregon

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  14. Understanding High School Graduation Rates in Kansas

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  15. Understanding High School Graduation Rates in Virginia

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  16. Understanding High School Graduation Rates in Connecticut

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  17. Understanding High School Graduation Rates in Hawaii

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  18. Understanding High School Graduation Rates in Vermont

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  19. Understanding High School Graduation Rates in Mississippi

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  20. Understanding High School Graduation Rates in California

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  1. Understanding High School Graduation Rates in Ohio

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  2. Understanding High School Graduation Rates in Montana

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  3. Understanding High School Graduation Rates in Maine

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  4. Understanding High School Graduation Rates in Washington

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  5. Understanding High School Graduation Rates in Louisiana

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  6. Understanding High School Graduation Rates in Colorado

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  7. Understanding High School Graduation Rates in Michigan

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  8. Understanding High School Graduation Rates in Indiana

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  9. Understanding High School Graduation Rates in Utah

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  10. Understanding High School Graduation Rates in Alabama

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  11. Understanding High School Graduation Rates in Arkansas

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  12. Understanding High School Graduation Rates in Missouri

    Science.gov (United States)

    Alliance for Excellent Education, 2009

    2009-01-01

    Graduation rates are a fundamental indicator of whether or not the nation's public school system is doing what it is intended to do: enroll, engage, and educate youth to be productive members of society. Since almost 90 percent of the fastest-growing and highest-paying jobs require some postsecondary education, having a high school diploma and the…

  13. Bit Preservation: A Solved Problem?

    Directory of Open Access Journals (Sweden)

    David S. H. Rosenthal

    2010-07-01

    Full Text Available For years, discussions of digital preservation have routinely featured comments such as “bit preservation is a solved problem; the real issues are ...”. Indeed, current digital storage technologies are not just astoundingly cheap and capacious, they are astonishingly reliable. Unfortunately, these attributes drive a kind of “Parkinson’s Law” of storage, in which demands continually push beyond the capabilities of systems implementable at an affordable price. This paper is in four parts:Claims, reviewing a typical claim of storage system reliability, showing that it provides no useful information for bit preservation purposes.Theory, proposing “bit half-life” as an initial, if inadequate, measure of bit preservation performance, expressing bit preservation requirements in terms of it, and showing that the requirements being placed on bit preservation systems are so onerous that the experiments required to prove that a solution exists are not feasible.Practice, reviewing recent research into how well actual storage systems preserve bits, showing that they fail to meet the requirements by many orders of magnitude.Policy, suggesting ways of dealing with this unfortunate situation.

  14. CRUCIAL: Cryosat-2 Success over Inland Water and Land: Analyses and Validation of SAR and SARin Full Bit Rate Altimetric Heights

    Science.gov (United States)

    Moore, Philip; Benveniste, Jérôme; Birkinshaw, Stephen; Ambrózio, Américo; Restano, Marco

    2016-07-01

    CRUCIAL is an ESA/STSE funded project investigating innovative land and inland water applications from Cryosat-2 with a forward-look component to the future Sentinel-3 and Jason-CS/Sentinel-6 missions. The high along-track sampling of Cryosat-2 in its SAR and SARin modes offer the opportunity to recover high frequency signals over inland waters. A theoretical approach has been developed to process the FBR L1A Doppler beams to form a product using ground cell gridding, beam steering and beam stacking from which inland water heights are derivable from the retracked Cryosat-2 altimetric waveforms. Results of the processing strategy will include a comparison of waveforms and heights from the burst echoes (˜80 m along-track) and from multi-look waveforms (˜320 m along-track). SAR and SARin FBR data are available for the Amazon, Brahmaputra and Mekong for 2011-2015. FBR SAR results will be compared against stage data from the nearest gauge where applicable with heights from Tonle Sap compared against Jason-2 data from the United States Department of Agriculture. A strategy to select the number of multi-looks over rivers will also be presented. Results of FBR SARin processing for the Amazon and Brahmaputra will be presented including comparison of heights from the two antennae, extraction of slope of the ground surface and validation against ground data where appropriate.

  15. A miniature high repetition rate shock tube.

    Science.gov (United States)

    Tranter, R S; Lynch, P T

    2013-09-01

    A miniature high repetition rate shock tube with excellent reproducibility has been constructed to facilitate high temperature, high pressure, gas phase experiments at facilities such as synchrotron light sources where space is limited and many experiments need to be averaged to obtain adequate signal levels. The shock tube is designed to generate reaction conditions of T > 600 K, P shock waves with predictable characteristics are created, repeatably. Two synchrotron-based experiments using this apparatus are also briefly described here, demonstrating the potential of the shock tube for research at synchrotron light sources.

  16. High strain rate behaviour of polypropylene microfoams

    Science.gov (United States)

    Gómez-del Río, T.; Garrido, M. A.; Rodríguez, J.; Arencón, D.; Martínez, A. B.

    2012-08-01

    Microcellular materials such as polypropylene foams are often used in protective applications and passive safety for packaging (electronic components, aeronautical structures, food, etc.) or personal safety (helmets, knee-pads, etc.). In such applications the foams which are used are often designed to absorb the maximum energy and are generally subjected to severe loadings involving high strain rates. The manufacture process to obtain polymeric microcellular foams is based on the polymer saturation with a supercritical gas, at high temperature and pressure. This method presents several advantages over the conventional injection moulding techniques which make it industrially feasible. However, the effect of processing conditions such as blowing agent, concentration and microfoaming time and/or temperature on the microstructure of the resulting microcellular polymer (density, cell size and geometry) is not yet set up. The compressive mechanical behaviour of several microcellular polypropylene foams has been investigated over a wide range of strain rates (0.001 to 3000 s-1) in order to show the effects of the processing parameters and strain rate on the mechanical properties. High strain rate tests were performed using a Split Hopkinson Pressure Bar apparatus (SHPB). Polypropylene and polyethylene-ethylene block copolymer foams of various densities were considered.

  17. High strain rate behaviour of polypropylene microfoams

    Directory of Open Access Journals (Sweden)

    Martínez A.B.

    2012-08-01

    Full Text Available Microcellular materials such as polypropylene foams are often used in protective applications and passive safety for packaging (electronic components, aeronautical structures, food, etc. or personal safety (helmets, knee-pads, etc.. In such applications the foams which are used are often designed to absorb the maximum energy and are generally subjected to severe loadings involving high strain rates. The manufacture process to obtain polymeric microcellular foams is based on the polymer saturation with a supercritical gas, at high temperature and pressure. This method presents several advantages over the conventional injection moulding techniques which make it industrially feasible. However, the effect of processing conditions such as blowing agent, concentration and microfoaming time and/or temperature on the microstructure of the resulting microcellular polymer (density, cell size and geometry is not yet set up. The compressive mechanical behaviour of several microcellular polypropylene foams has been investigated over a wide range of strain rates (0.001 to 3000 s−1 in order to show the effects of the processing parameters and strain rate on the mechanical properties. High strain rate tests were performed using a Split Hopkinson Pressure Bar apparatus (SHPB. Polypropylene and polyethylene-ethylene block copolymer foams of various densities were considered.

  18. Dynamic Power-Saving Method for Wi-Fi Direct Based IoT Networks Considering Variable-Bit-Rate Video Traffic

    Directory of Open Access Journals (Sweden)

    Meihua Jin

    2016-10-01

    Full Text Available With the arrival of the era of Internet of Things (IoT, Wi-Fi Direct is becoming an emerging wireless technology that allows one to communicate through a direct connection between the mobile devices anytime, anywhere. In Wi-Fi Direct-based IoT networks, all devices are categorized by group of owner (GO and client. Since portability is emphasized in Wi-Fi Direct devices, it is essential to control the energy consumption of a device very efficiently. In order to avoid unnecessary power consumed by GO, Wi-Fi Direct standard defines two power-saving methods: Opportunistic and Notice of Absence (NoA power-saving methods. In this paper, we suggest an algorithm to enhance the energy efficiency of Wi-Fi Direct power-saving, considering the characteristics of multimedia video traffic. Proposed algorithm utilizes the statistical distribution for the size of video frames and adjusts the lengths of awake intervals in a beacon interval dynamically. In addition, considering the inter-dependency among video frames, the proposed algorithm ensures that a video frame having high priority is transmitted with higher probability than other frames having low priority. Simulation results show that the proposed method outperforms the traditional NoA method in terms of average delay and energy efficiency.

  19. Dynamic Power-Saving Method for Wi-Fi Direct Based IoT Networks Considering Variable-Bit-Rate Video Traffic.

    Science.gov (United States)

    Jin, Meihua; Jung, Ji-Young; Lee, Jung-Ryun

    2016-10-12

    With the arrival of the era of Internet of Things (IoT), Wi-Fi Direct is becoming an emerging wireless technology that allows one to communicate through a direct connection between the mobile devices anytime, anywhere. In Wi-Fi Direct-based IoT networks, all devices are categorized by group of owner (GO) and client. Since portability is emphasized in Wi-Fi Direct devices, it is essential to control the energy consumption of a device very efficiently. In order to avoid unnecessary power consumed by GO, Wi-Fi Direct standard defines two power-saving methods: Opportunistic and Notice of Absence (NoA) power-saving methods. In this paper, we suggest an algorithm to enhance the energy efficiency of Wi-Fi Direct power-saving, considering the characteristics of multimedia video traffic. Proposed algorithm utilizes the statistical distribution for the size of video frames and adjusts the lengths of awake intervals in a beacon interval dynamically. In addition, considering the inter-dependency among video frames, the proposed algorithm ensures that a video frame having high priority is transmitted with higher probability than other frames having low priority. Simulation results show that the proposed method outperforms the traditional NoA method in terms of average delay and energy efficiency.

  20. Synchronization of random bit generators based on coupled chaotic lasers and application to cryptography.

    Science.gov (United States)

    Kanter, Ido; Butkovski, Maria; Peleg, Yitzhak; Zigzag, Meital; Aviad, Yaara; Reidler, Igor; Rosenbluh, Michael; Kinzel, Wolfgang

    2010-08-16

    Random bit generators (RBGs) constitute an important tool in cryptography, stochastic simulations and secure communications. The later in particular has some difficult requirements: high generation rate of unpredictable bit strings and secure key-exchange protocols over public channels. Deterministic algorithms generate pseudo-random number sequences at high rates, however, their unpredictability is limited by the very nature of their deterministic origin. Recently, physical RBGs based on chaotic semiconductor lasers were shown to exceed Gbit/s rates. Whether secure synchronization of two high rate physical RBGs is possible remains an open question. Here we propose a method, whereby two fast RBGs based on mutually coupled chaotic lasers, are synchronized. Using information theoretic analysis we demonstrate security against a powerful computational eavesdropper, capable of noiseless amplification, where all parameters are publicly known. The method is also extended to secure synchronization of a small network of three RBGs.

  1. A Bit Stream Scalable Speech/Audio Coder Combining Enhanced Regular Pulse Excitation and Parametric Coding

    Directory of Open Access Journals (Sweden)

    Albertus C. den Brinker

    2007-01-01

    Full Text Available This paper introduces a new audio and speech broadband coding technique based on the combination of a pulse excitation coder and a standardized parametric coder, namely, MPEG-4 high-quality parametric coder. After presenting a series of enhancements to regular pulse excitation (RPE to make it suitable for the modeling of broadband signals, it is shown how pulse and parametric codings complement each other and how they can be merged to yield a layered bit stream scalable coder able to operate at different points in the quality bit rate plane. The performance of the proposed coder is evaluated in a listening test. The major result is that the extra functionality of the bit stream scalability does not come at the price of a reduced performance since the coder is competitive with standardized coders (MP3, AAC, SSC.

  2. A low-power 10-bit 250-KSPS cyclic ADC with offset and mismatch correction*

    Institute of Scientific and Technical Information of China (English)

    Zhao Hongliang; Zhao Yiqiang; Geng Junfeng; Li Peng; Zhang Zhisheng

    2011-01-01

    A low power 10-bit 250-k sample per second (KSPS) cyclic analog to digital converter (ADC) is presented. The ADC's offset errors are successfully cancelled out through the proper choice of a capacitor switching sequence. The improved redundant signed digit algorithm used in the ADC can tolerate high levels of the comparator's offset errors and switched capacitor mismatch errors. With this structure, it has the advantages of simple circuit configuration, small chip area and low power dissipation. The cyclic ADC manufactured with the Chartered 0.35 μm 2P4M process shows a 58.5 dB signal to noise and distortion ratio and a 9.4 bit effective number of bits at a 250 KSPS sample rate. It dissipates 0.72 mW with a 3.3 V power supply and occupies dimensions of 0.42 × 0.68 mm2.

  3. High strain rate characterization of polymers

    Science.gov (United States)

    Siviour, Clive R.

    2017-01-01

    This paper reviews the literature on the response of polymers to high strain rate deformation. The main focus is on the experimental techniques used to characterize this response. The paper includes a small number of examples as well as references to experimental data over a wide range of rates, which illustrate the key features of rate dependence in these materials; however this is by no means an exhaustive list. The aim of the paper is to give the reader unfamiliar with the subject an overview of the techniques available with sufficient references from which further information can be obtained. In addition to the `well established' techniques of the Hopkinson bar, Taylor Impact and Transverse impact, a discussion of the use of time-temperature superposition in interpreting and experimentally replicating high rate response is given, as is a description of new techniques in which mechanical parameters are derived by directly measuring wave propagation in specimens; these are particularly appropriate for polymers with low wave speeds. The vast topic of constitutive modelling is deliberately excluded from this review.

  4. Hey! A Gnat Bit Me!

    Science.gov (United States)

    ... Hey! A Bee Stung Me! Rashes: The Itchy Truth Hey! A Mosquito Bit Me! Contact Us Print ... The Nemours Foundation, iStock, Getty Images, Corbis, Veer, Science Photo Library, Science Source Images, Shutterstock, and Clipart. ...

  5. Hey! A Louse Bit Me!

    Science.gov (United States)

    ... Hey! A Chigger Bit Me! Rashes: The Itchy Truth Contact Us Print Resources Send to a Friend ... The Nemours Foundation, iStock, Getty Images, Corbis, Veer, Science Photo Library, Science Source Images, Shutterstock, and Clipart. ...

  6. Hey! A Bedbug Bit Me!

    Science.gov (United States)

    ... Black Widow Spider Bit Me! Rashes: The Itchy Truth Contact Us Print Resources Send to a Friend ... The Nemours Foundation, iStock, Getty Images, Corbis, Veer, Science Photo Library, Science Source Images, Shutterstock, and Clipart. ...

  7. A prototype of a high rating MRPC

    Institute of Scientific and Technical Information of China (English)

    WANG Yi; WANG Jing-Bo; YAN Qiang; LI Yuan-Jing; CHENG Jian-Ping; YUE Qian; LI Jin

    2009-01-01

    Six-gap resistive plate chamber (MRPC) prototypes with semiconductive glass electrodes (bulk resistivity~1010.cm) were studied for suitability in time-of-flight (TOF) applications at high rates. These studies were performed using a continuous electron beam of 800 MeV at IHEP and an X-ray machine. Time resolutions of about 100 ps and efficiencies larger than 90% were obtained for flux densities up to 28 kHz/cm2.

  8. Reserve, flowing electrolyte, high rate lithium battery

    Science.gov (United States)

    Puskar, M.; Harris, P.

    Flowing electrolyte Li/SOCl2 tests in single cell and multicell bipolar fixtures have been conducted, and measurements are presented for electrolyte flow rates, inlet and outlet temperatures, fixture temperatures at several points, and the pressure drop across the fixture. Reserve lithium batteries with flowing thionyl-chloride electrolytes are found to be capable of very high energy densities with usable voltages and capacities at current densities as high as 500 mA/sq cm. At this current density, a battery stack 10 inches in diameter is shown to produce over 60 kW of power while maintaining a safe operating temperature.

  9. DEVELOPMENT OF A HIGH RATE HIGH RESOLUTION DETECTOR FOR EXAFS EXPERIMENTS.

    Energy Technology Data Exchange (ETDEWEB)

    DE GERONIMO,G.; O CONNOR,P.; BEUTTENMULLER,R.H.; LI,Z.; KUCZEWSKI,A.J.; SIDDONS,D.P.

    2002-11-10

    A new detector for EXAFS experiments is being developed. It is based on a multi-element Si sensor and dedicated readout ASICs. The sensor is composed of 384 pixels, each having 1 mm{sup 2} area, arranged in four quadrants of 12 x 8 elements, and wire-bonded to 32-channel front-end ASICs. Each channel implements low noise preamplification with self-adaptive continuous reset, high order shaper, band-gap referenced baseline stabilizer, one threshold comparator and two DAC adjustable window comparators, each followed by a 24-bit counter. Fabricated in 0.35{micro}m CMOS dissipates about 8mW per channel. First measurements show at room temperature a resolution of 14 rms electrons without the detector and of 40 rms electrons (340eV) with the detector connected and biased. Cooling at -35C a FWHM of 205eV (167eV from electronics) was measured at the Mn-K{alpha} line. A resolution of about 300eV was measured for rates approaching 100kcps/cm{sup 2} per channel, corresponding to an overall rate in excess of 10MHz/cm{sup 2}. A channel-to-channel threshold dispersion after DACs adjustment of 2.5 rms electrons was also measured.

  10. String bit models for superstring

    Energy Technology Data Exchange (ETDEWEB)

    Bergman, O.; Thorn, C.B.

    1995-12-31

    The authors extend the model of string as a polymer of string bits to the case of superstring. They mainly concentrate on type II-B superstring, with some discussion of the obstacles presented by not II-B superstring, together with possible strategies for surmounting them. As with previous work on bosonic string work within the light-cone gauge. The bit model possesses a good deal less symmetry than the continuous string theory. For one thing, the bit model is formulated as a Galilei invariant theory in (D {minus} 2) + 1 dimensional space-time. This means that Poincare invariance is reduced to the Galilei subgroup in D {minus} 2 space dimensions. Naturally the supersymmetry present in the bit model is likewise dramatically reduced. Continuous string can arise in the bit models with the formation of infinitely long polymers of string bits. Under the right circumstances (at the critical dimension) these polymers can behave as string moving in D dimensional space-time enjoying the full N = 2 Poincare supersymmetric dynamics of type II-B superstring.

  11. Over-the-air demonstration of spatial multiplexing at high data rates using real-time base-band processing

    Directory of Open Access Journals (Sweden)

    V. Jungnickel

    2004-01-01

    Full Text Available Over-the-air transmission experiments with a realtime MIMO test-bed are reported. We describe in principle a hardware architecture for spatial multiplexing at high data rates, discuss in detail the implementation on a hybrid FPGA/DSP platform and show measured bit error rates from indoor transmission experiments. Per-antenna rate control and joint transmission are enabled as well using an ideal feed-back link. A functional test of these new techniques is described while detailed transmission experiments are still ongoing.

  12. High strain rate deformation of layered nanocomposites

    Science.gov (United States)

    Lee, Jae-Hwang; Veysset, David; Singer, Jonathan P.; Retsch, Markus; Saini, Gagan; Pezeril, Thomas; Nelson, Keith A.; Thomas, Edwin L.

    2012-11-01

    Insight into the mechanical behaviour of nanomaterials under the extreme condition of very high deformation rates and to very large strains is needed to provide improved understanding for the development of new protective materials. Applications include protection against bullets for body armour, micrometeorites for satellites, and high-speed particle impact for jet engine turbine blades. Here we use a microscopic ballistic test to report the responses of periodic glassy-rubbery layered block-copolymer nanostructures to impact from hypervelocity micron-sized silica spheres. Entire deformation fields are experimentally visualized at an exceptionally high resolution (below 10 nm) and we discover how the microstructure dissipates the impact energy via layer kinking, layer compression, extreme chain conformational flattening, domain fragmentation and segmental mixing to form a liquid phase. Orientation-dependent experiments show that the dissipation can be enhanced by 30% by proper orientation of the layers.

  13. Reversible n-Bit to n-Bit Integer Haar-Like Transforms

    Energy Technology Data Exchange (ETDEWEB)

    Senecal, J; Duchaineau, M; Joy, K I

    2003-11-03

    We introduce a wavelet-like transform similar to the Haar transform, but with the properties that it packs the results into the same number of bits as the original data, and is reversible. Our method, called TLHaar, uses table lookups to replace the averaging, differencing, and bit shifting performed in a Haar IntegerWavelet Transform (IWT). TLHaar maintains the same coefficient magnitude relationships for the low- and high-pass coefficients as true Haar, but reorders them to fit into the same number of bits as the input signal, thus eliminating the sign bit that is added to the Haar IWT output coefficients. Eliminating the sign bit avoids using extra memory and speeds the transform process. We tested TLHaar on a variety of image types, and when compared to the Haar IWT TLHaar is significantly faster. For image data with lines or hard edges TLHaar coefficients compress better than those of the Haar IWT. Due to its speed TLHaar is suitable for streaming hardware implementations with fixed data sizes, such as DVI channels.

  14. High frame-rate digital radiographic videography

    Energy Technology Data Exchange (ETDEWEB)

    King, N.S.P.; Cverna, F.H.; Albright, K.L.; Jaramillo, S.A.; Yates, G.J.; McDonald, T.E. [Los Alamos National Lab., NM (United States); Flynn, M.J.; Tashman, S. [Henry Ford Health System, Detroit, MI (United States)

    1994-09-01

    High speed x-ray imaging can be an important tool for observing internal processes in a wide range of applications. In this paper we describe preliminary implementation of a system having the eventual goal of observing the internal dynamics of bone and joint reactions during loading. Two Los Alamos National Laboratory (LANL) gated and image intensified camera systems were used to record images from an x-ray image convertor tube to demonstrate the potential of high frame-rate digital radiographic videography in the analysis of bone and joint dynamics of the human body. Preliminary experiments were done at LANL to test the systems. Initial high frame-rate imaging (from 500 to 1000 frames/s) of a swinging pendulum mounted to the face of an X-ray image convertor tube demonstrated high contrast response and baseline sensitivity. The systems were then evaluated at the Motion Analysis Laboratory of Henry Ford Health Systems Bone and Joint Center. Imaging of a 9 inch acrylic disk with embedded lead markers rotating at approximately 1000 RPM, demonstrated the system response to a high velocity/high contrast target. By gating the P-20 phosphor image from the X-ray image convertor with a second image intensifier (II) and using a 100-microsecond wide optical gate through the second II, enough prompt light decay from the x-ray image convertor phosphor had taken place to achieve reduction of most of the motion blurring. Measurement of the marker velocity was made by using video frames acquired at 500 frames/s. The data obtained from both experiments successfully demonstrated the feasibility of the technique. Several key areas for improvement are discussed along with salient test results and experiment details.

  15. Bits and q-bits as versatility measures

    Directory of Open Access Journals (Sweden)

    José R.C. Piqueira

    2004-06-01

    Full Text Available Using Shannon information theory is a common strategy to measure any kind of variability in a signal or phenomenon. Some methods were developed to adapt information entropy measures to bird song data trying to emphasize its versatility aspect. This classical approach, using the concept of bit, produces interesting results. Now, the original idea developed in this paper is to use the quantum information theory and the quantum bit (q-bit concept in order to provide a more complete vision of the experimental results.Usar a teoria da informação de Shannon é uma estratégia comum para medir todo tipo de variabilidade em um sinal ou fenômeno. Alguns métodos foram desenvolvidos para adaptar a medida de entropia informacional a dados de cantos de pássaro, tentando enfatizar seus aspectos de versatilidade. Essa abordagem clássica, usando o conceito de bit, produz resultados interessantes. Agora, a idéia original desenvolvida neste artigo é usar a teoria quântica da informação e o conceito de q-bit, com a finalidade de proporcionar uma visão mais completa dos resultados experimentais.

  16. Novel High Rate Lithium Intercalation Cathode Materials

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Application of amorphous V2O5/carbon/neodymium oxide (Nd2O3) composite is one of ways to surmount the lower electrical conductivity of V2O5. A new type of V2O5/carbon/Nd2O3 composite was prepared by mixing vanadium oxide hydrosol, acetone, carbon and Nd2O3 powder. High rate discharge/charge property of the composite electrode was tested electrochemically. This composite with Nd2O3 added shows the improvement of not only the discharge capacity but also cycle durability discharge capacity. The rate capability of the composite cathode also increases with the addition of Nd2O3.and cycle life are probably caused by the increase in porosity of open pores and short diffusion length of the active material on the lithium-ion insertion.

  17. 一个高线性13位流水线CMOS A/D转换器%A High Linearity, 13bit Pipelined CMOS ADC

    Institute of Scientific and Technical Information of China (English)

    李福乐; 段静波; 王志华

    2008-01-01

    介绍了一个采用多种电路设计技术来实现高线性13位流水线A/D转换器.这些设计技术包括采用无源电容误差平均来校准电容失配误差、增益增强(gain-boosting)运放来降低有限增益误差和增益非线性,自举(bootstrapping)开关来减小开关导通电阻的非线性以及抗干扰设计来减弱来自数字供电的噪声.电路采用0.18μm CMOS工艺实现,包括焊盘在内的面积为3.2mm2.在2.5MHz采样时钟和2.4MHz输入信号下测试,得到的微分非线性为-0.18/0.15LSB,积分非线性为-0.35/0.5LSB,信号与噪声加失真比(SNDR)为75.7dB,无杂散动态范围(SFDR)为90.5dBc;在5MHz采样时钟和2.4MHz输入信号下测试,得到的SNDR和SFDR分别为73.7dB和83.9dBc.所有测试均在2.7V电源下进行,对应于采样率为2.5MS/s和5Ms/s的功耗(包括焊盘驱动电路)分别为21mW和34mW.%A 13bit,pipelined analog-to-digital converter (ADC) designed to achieve high linearity is described. The high linearity is realized by using the passive capacitor error-averaging technique to calibrate the capacitor mismatch error, a gain-boosting opamp to minimize the finite gain error and gain nonlinearity, a bootstrapping switch to reduce the switch on-resistor nonlinearity, and an anti-disturb design to reduce the noise from the digital supply. This ADC is implemented in 0.18μm CMOS technology and occupies a die area of 3.2mm2 , including pads. Measured performance includes-0.18/ 0.15LSB of differential nonlinearity,-0.35/0.5LSB of integral nonlinearity, 75.7dB of signal-to-noise plus distortion ra- tio (SNDR) and 90. 5 dBc of spurious-free dynamic range (SFDR) for 2. 4MHz input at 2.5MS/s. At full speed conversion (5MS/s) and for the same 2.4MHz input, the measured SNDR and SFDR are 73.7dB and 83.9 dBc, respectively. The power dissipation including output pad drivers is 21mW at 2.5MS/s and 34mW at 5MS/s,both at 2. 7V supply.

  18. A Pulsed Coding Technique Based on Optical UWB Modulation for High Data Rate Low Power Wireless Implantable Biotelemetry

    Directory of Open Access Journals (Sweden)

    Andrea De Marcellis

    2016-10-01

    Full Text Available This paper reports on a pulsed coding technique based on optical Ultra-wideband (UWB modulation for wireless implantable biotelemetry systems allowing for high data rate link whilst enabling significant power reduction compared to the state-of-the-art. This optical data coding approach is suitable for emerging biomedical applications like transcutaneous neural wireless communication systems. The overall architecture implementing this optical modulation technique employs sub-nanosecond pulsed laser as the data transmitter and small sensitive area photodiode as the data receiver. Moreover, it includes coding and decoding digital systems, biasing and driving analogue circuits for laser pulse generation and photodiode signal conditioning. The complete system has been implemented on Field-Programmable Gate Array (FPGA and prototype Printed Circuit Board (PCB with discrete off-the-shelf components. By inserting a diffuser between the transmitter and the receiver to emulate skin/tissue, the system is capable to achieve a 128 Mbps data rate with a bit error rate less than 10−9 and an estimated total power consumption of about 5 mW corresponding to a power efficiency of 35.9 pJ/bit. These results could allow, for example, the transmission of an 800-channel neural recording interface sampled at 16 kHz with 10-bit resolution.

  19. AN IMPROVED BIT LOADING TECHNIQUE FOR ENHANCED ENERGY EFFICIENCY IN NEXT GENERATION VOICE/VIDEO APPLICATIONS

    Directory of Open Access Journals (Sweden)

    VINOTH BABU K.

    2016-04-01

    Full Text Available Multi input multi output (MIMO and orthogonal frequency division multiplexing (OFDM are the key techniques for the future wireless communication systems. Previous research in the above areas mainly concentrated on spectral efficiency improvement and very limited work has been done in terms of energy efficient transmission. In addition to spectral efficiency improvement, energy efficiency improvement has become an important research because of the slow progressing nature of the battery technology. Since most of the user equipments (UE rely on battery, the energy required to transmit the target bits should be minimized to avoid quick battery drain. The frequency selective fading nature of the wireless channel reduces the spectral and energy efficiency of OFDM based systems. Dynamic bit loading (DBL is one of the suitable solution to improve the spectral and energy efficiency of OFDM system in frequency selective fading environment. Simple dynamic bit loading (SDBL algorithm is identified to offer better energy efficiency with less system complexity. It is well suited for fixed data rate voice/video applications. When the number of target bits are very much larger than the available subcarriers, the conventional single input single output (SISO-SDBL scheme offers high bit error rate (BER and needs large transmit energy. To improve bit error performance we combine space frequency block codes (SFBC with SDBL, where the adaptations are done in both frequency and spatial domain. To improve the quality of service (QoS further, optimal transmit antenna selection (OTAS scheme is also combined with SFBC-SDBL scheme. The simulation results prove that the proposed schemes offer better QoS when compared to the conventional SISOSDBL scheme.

  20. Experimental recombination rates for highly charged ions

    Energy Technology Data Exchange (ETDEWEB)

    Reinhold Schuch [Dept. of Atomic Physics, Stockholm Univ., Frescativ., Stockholm (Sweden)

    2000-01-01

    Recent studies of recombination between free electrons and highly charged ions using electron coolers of heavy-ion storage rings have produced accurate rate coefficients of interest for plasma modeling and diagnostics. Some surprises were discovered which can lead to revisions of recombination models. With bare ions one finds at low energy a strong and puzzling deviation from radiative recombination theory. Dielectronic recombination with C3+, N4+ show that jj coupling gives essential contributions to the cross section also for light ions. (author)

  1. Modeling and analysis of stick-slip and bit bounce in oil well drillstrings equipped with drag bits

    Science.gov (United States)

    Kamel, Jasem M.; Yigit, Ahmet S.

    2014-12-01

    Rotary drilling systems equipped with drag bits or fixed cutter bits (also called PDC), used for drilling deep boreholes for the production and the exploration of oil and natural gas, often suffer from severe vibrations. These vibrations are detrimental to the bit and the drillstring causing different failures of equipment (e.g., twist-off, abrasive wear of tubulars, bit damage), and inefficiencies in the drilling operation (reduction of the rate of penetration (ROP)). Despite extensive research conducted in the last several decades, there is still a need to develop a consistent model that adequately captures all phenomena related to drillstring vibrations such as nonlinear cutting and friction forces at the bit/rock formation interface, drive system characteristics and coupling between various motions. In this work, a physically consistent nonlinear model for the axial and torsional motions of a rotating drillstring equipped with a drag bit is proposed. A more realistic cutting and contact model is used to represent bit/rock formation interaction at the bit. The dynamics of both drive systems for rotary and translational motions of the drillstring, including the hoisting system are also considered. In this model, the rotational and translational motions of the bit are obtained as a result of the overall dynamic behavior rather than prescribed functions or constants. The dynamic behavior predicted by the proposed model qualitatively agree well with field observations and published theoretical results. The effects of various operational parameters on the dynamic behavior are investigated with the objective of achieving a smooth and efficient drilling. The results show that with proper choice of operational parameters, it may be possible to minimize the effects of stick-slip and bit-bounce and increase the ROP. Therefore, it is expected that the results will help reduce the time spent in drilling process and costs incurred due to severe vibrations and consequent

  2. Silicon chip based wavelength conversion of ultra-high repetition rate data signals

    DEFF Research Database (Denmark)

    Hu, Hao; Ji, Hua; Galili, Michael

    2011-01-01

    We report on all-optical wavelength conversion of 160, 320 and 640 Gbit/s line-rate data signals using four-wave mixing in a 3.6 mm long silicon waveguide. Bit error rate measurements validate the performance within FEC limits.......We report on all-optical wavelength conversion of 160, 320 and 640 Gbit/s line-rate data signals using four-wave mixing in a 3.6 mm long silicon waveguide. Bit error rate measurements validate the performance within FEC limits....

  3. Recrystallization of High Carbon Steel during High Strain Rate

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The recrystallization of high carbon steel during high temperature and high speed rolling has been studied by analyzing the stress-strain curves and the austenite grain size.Isothermal multi-pass hot compression at high strain rate was carried out by Gleeble-2000. The austenite grain size was measured by IBAS image analysis system. The results show that static recrystallization occurred at interpass time under pre-finish rolling, and at the finish rolling stage, due to the brief interpass time, static recrystallization can not be found.

  4. The design and development of a high-resolution visible-to-near-UV telescope for balloon-borne astronomy: SuperBIT

    CERN Document Server

    Romualdez, L Javier; Clark, Paul; Damaren, Christopher J; Eifler, Tim; Fraisse, Aurelien A; Galloway, Mathew N; Hartley, John W; Jones, William C; Li, Lun; Lipton, Leeav; Luu, Thuy Vy T; Massey, Richard J; Netterfield, C Barth; Padilla, Ivan; Rhodes, Jason D; Schmoll, Jürgen

    2016-01-01

    Balloon-borne astronomy is unique in that it allows for a level of image stability, resolution, and optical backgrounds that are comparable to space-borne systems due to greatly reduced atmospheric interference, but at a fraction of the cost and over a significantly reduced development time-scale. Instruments operating within visible-to-near-UV bands ($300$ - $900$ um) can achieve a theoretical diffraction limited resolution of $0.01"$ from the stratosphere ($35$ - $40$ km altitude) without the need for extensive adaptive optical systems required by ground-based systems. The {\\it Superpressure Balloon-borne Imaging Telescope} ("SuperBIT") is a wide-field imager designed to achieve 0.02$"$ stability over a 0.5$^\\circ$ field-of-view, for deep single exposures of up to 5 minutes. SuperBIT is thus well-suited for many astronomical observations, from solar or extrasolar planetary observations, to resolved stellar populations and distant galaxies (whether to study their morphology, evolution, or gravitational lensi...

  5. A Holistic Approach to Bit Preservation

    DEFF Research Database (Denmark)

    Zierau, Eld Maj-Britt Olmütz

    2011-01-01

    This thesis presents three main results for a holistic approach to bit preservation, where the ultimate goal is to find the optimal bit preservation strategy for specific digital material that must be digitally preserved. Digital material consists of sequences of bits, where a bit is a binary dig...

  6. High counting rate resistive-plate chamber

    Science.gov (United States)

    Peskov, V.; Anderson, D. F.; Kwan, S.

    1993-05-01

    Parallel-plate avalanche chambers (PPAC) are widely used in physics experiments because they are fast (less than 1 ns) and have very simple construction: just two parallel metallic plates or mesh electrodes. Depending on the applied voltage they may work either in spark mode or avalanche mode. The advantage of the spark mode of operation is a large signal amplitude from the chamber, the disadvantage is that there is a large dead time (msec) for the entire chamber after an event. The main advantage of the avalanche mode is high rate capability 10(exp 5) counts/mm(sup 2). A resistive-plate chamber (RPC) is similar to the PPAC in construction except that one or both of the electrodes are made from high resistivity (greater than 10(exp 10) Omega(cm) materials. In practice RPC's are usually used in the spark mode. Resistive electrodes are charged by sparks, locally reducing the actual electric field in the gap. The size of the charged surface is about 10 mm(sup 2), leaving the rest of the detector unaffected. Therefore, the rate capability of such detectors in the spark mode is considerably higher than conventional spark counters. Among the different glasses tested the best results were obtained with electron type conductive glasses, which obey Ohm's law. Most of the work with such glasses was done with high pressure parallel-plate chambers (10 atm) for time-of-flight measurements. Resistive glasses have been expensive and produced only in small quantities. Now resistive glasses are commercially available, although they are still expensive in small scale production. From the positive experience of different groups working with the resistive glasses, it was decided to review the old idea to use this glass for the RPC. This work has investigated the possibility of using the RPC at 1 atm and in the avalanche mode. This has several advantages: simplicity of construction, high rate capability, low voltage operation, and the ability to work with non-flammable gases.

  7. Chuanshi Brand Tri-cone Roller Bit

    Institute of Scientific and Technical Information of China (English)

    Chen Xilong; Shen Zhenzhong; Yuan Xiaoyi

    1997-01-01

    @@ Compared with other types of bits, the tri-cone roller bit has the advantages of excellent comprehensive performance, low price, wide usage range. It is free of formation limits. The tri-cone roller bit accounts for 90% of the total bits in use. The Chengdu Mechanical Works, as a major manufacturer of petroleum mechanical products and one of the four major tri-cone roller bit factories in China,has produced 120 types of bits in seven series and 19 sizes since 1967. The bits manufactured by the factory are not only sold to the domestic oilfields, but also exported to Japan, Thailand, Indonesia, the Philippines and the Middle East.

  8. Bits through ARQs

    CERN Document Server

    Eswaran, Krishnan; Ramchandran, Kannan

    2008-01-01

    A fundamental problem in dynamic frequency reuse is that the cognitive radio is ignorant of the amount of interference it inflicts on the primary license holder. A model for such a situation is proposed and analyzed. The primary sends packets across an erasure channel and employs simple ACK/NAK feedback (ARQs) to retransmit erased packets. Furthermore, its erasure probabilities are influenced by the cognitive radio's activity. While the cognitive radio does not know these interference characteristics, it can eavesdrop on the primary's ARQs. The model leads to strategies in which the cognitive radio adaptively adjusts its input based on the primary's ARQs thereby guaranteeing the primary exceeds a target packet rate. A relatively simple strategy whereby the cognitive radio transmits only when the primary's empirical packet rate exceeds a threshold is shown to have interesting universal properties in the sense that for unknown time-varying interference characteristics, the primary is guaranteed to meet its targ...

  9. Covert Bits Through Queues

    OpenAIRE

    Mukherjee, Pritam; Ulukus, Sennur

    2016-01-01

    We consider covert communication using a queuing timing channel in the presence of a warden. The covert message is encoded using the inter-arrival times of the packets, and the legitimate receiver and the warden observe the inter-departure times of the packets from their respective queues. The transmitter and the legitimate receiver also share a secret key to facilitate covert communication. We propose achievable schemes that obtain non-zero covert rate for both exponential and general queues...

  10. Methods to ensure optimal off-bottom and drill bit distance under pellet impact drilling

    OpenAIRE

    Kovalev, Artem Vladimirovich; Isaev, Evgeniy Dmitrievich; Vagapov, A. R.; Urnish, V. V.; Ulyanova, Oksana Sergeevna

    2016-01-01

    The paper describes pellet impact drilling which could be used to increase the drilling speed and the rate of penetration when drilling hard rock for various purposes. Pellet impact drilling implies rock destruction by metal pellets with high kinetic energy in the immediate vicinity of the earth formation encountered. The pellets are circulated in the bottom hole by a high velocity fluid jet, which is the principle component of the ejector pellet impact drill bit. The paper presents the surve...

  11. High-Rate Data-Capture for an Airborne Lidar System

    Science.gov (United States)

    Valett, Susan; Hicks, Edward; Dabney, Philip; Harding, David

    2012-01-01

    A high-rate data system was required to capture the data for an airborne lidar system. A data system was developed that achieved up to 22 million (64-bit) events per second sustained data rate (1408 million bits per second), as well as short bursts (less than 4 s) at higher rates. All hardware used for the system was off the shelf, but carefully selected to achieve these rates. The system was used to capture laser fire, single-photon detection, and GPS data for the Slope Imaging Multi-polarization Photo-counting Lidar (SIMPL). However, the system has applications for other laser altimeter systems (waveform-recording), mass spectroscopy, xray radiometry imaging, high-background- rate ranging lidar, and other similar areas where very high-speed data capture is needed. The data capture software was used for the SIMPL instrument that employs a micropulse, single-photon ranging measurement approach and has 16 data channels. The detected single photons are from two sources those reflected from the target and solar background photons. The instrument is non-gated, so background photons are acquired for a range window of 13 km and can comprise many times the number of target photons. The highest background rate occurs when the atmosphere is clear, the Sun is high, and the target is a highly reflective surface such as snow. Under these conditions, the total data rate for the 16 channels combined is expected to be approximately 22 million events per second. For each photon detection event, the data capture software reads the relative time of receipt, with respect to a one-per-second absolute time pulse from a GPS receiver, from an event timer card with 0.1-ns precision, and records that information to a RAID (Redundant Array of Independent Disks) storage device. The relative time of laser pulse firings must also be read and recorded with the same precision. Each of the four event timer cards handles the throughput from four of the channels. For each detection event, a flag is

  12. High-energy, high-rate materials processing

    Science.gov (United States)

    Marcus, H. L.; Bourell, D. L.; Eliezer, Z.; Persad, C.; Weldon, W.

    1987-12-01

    The increasingly available range of pulsed-power, high energy kinetic storage devices, such as low-inductance pulse-forming networks, compulsators, and homopolar generators, is presently considered as a basis for industrial high energy/high rate (HEHR) processing to accomplish shock hardening, drilling, rapid surface alloying and melting, welding and cutting, transformation hardening, and cladding and surface melting in metallic materials. Time-temperature-transformation concepts furnish the basis for a fundamental understanding of the potential advantages of this direct pulsed power processing. Attention is given to the HEHR processing of a refractory molybdenum alloy, a nickel-base metallic glass, tungsten, titanium aluminides, and metal-matrix composites.

  13. CW Interference Effects on High Data Rate Transmission Through the ACTS Wideband Channel

    Science.gov (United States)

    Kerczewski, Robert J.; Ngo, Duc H.; Tran, Quang K.; Tran, Diepchi T.; Yu, John; Kachmar, Brian A.; Svoboda, James S.

    1996-01-01

    Satellite communications channels are susceptible to various sources of interference. Wideband channels have a proportionally greater probability of receiving interference than narrowband channels. NASA's Advanced Communications Technology Satellite (ACTS) includes a 900 MHz bandwidth hardlimiting transponder which has provided an opportunity for the study of interference effects of wideband channels. A series of interference tests using two independent ACTS ground terminals measured the effects of continuous-wave (CW) uplink interference on the bit-error rate of a 220 Mbps digitally modulated carrier. These results indicate the susceptibility of high data rate transmissions to CW interference and are compared to results obtained with a laboratory hardware-based system simulation and a computer simulation.

  14. Single Carrier Architecture for High Data Rate Wireless PAN Communications System

    CERN Document Server

    Rakotondrainibe, Lahatra; Zaharia, Gheorghe; Grunfelder, Guy; Zein, Ghaïs El

    2010-01-01

    A 60 GHz wireless Gigabit Ethernet (G.E.) communication system is developed at IETR. As the 60 GHz radio link operates only in a single-room configuration, an additional Radio over Fibre (RoF) link is used to ensure the communications in all the rooms of a residential environment. The realized system covers 2 GHz bandwidth. Due to the hardware constraints, a symbol rate at 875 Mbps is attained using simple single carrier architecture. In the baseband (BB) processing block, an original byte/frame synchronization process is designed to provide a smaller value of the preamble missing detection and false alarm probabilities. Bit error rate (BER) measurements have been realized in a large gym for line-of-sight (LOS) conditions. A Tx-Rx distance greater than 30 meters was attained with low BER using high gain antennas and forward error correction RS (255, 239) coding.

  15. High-Frame-Rate Oil Film Interferometry

    CERN Document Server

    White, Jonathan C; Chen, John

    2010-01-01

    The fluid dynamics video to which this abstract relates contains visualization of the response of a laminar boundary layer to a sudden puff from a small hole. The boundary layer develops on a flat plate in a wind tunnel; the hole is located at a streamwise Reynolds number of 100,000. The visualization of the boundary layer response is accomplished using interferometry of a transparent, thin film of oil placed on the surface immediately downstream of the hole and with its leading edge perpendicular to the direction of flow. Through lubrication theory, it is understood that the rate of change of the spacing of the interference fringes is proportional to the skin friction at any instant. For reference, a small disk-shaped protrusion of the type often used to trip the boundary layer in wind model tunnel testing is also shown. Three cases with different puff strengths are included. Using a high-speed commercial camera, frame rates in excess of 1000/sec have been recorded; the video shown here was taken at 24 frame...

  16. High spin rate magnetic controller for nanosatellites

    Science.gov (United States)

    Slavinskis, A.; Kvell, U.; Kulu, E.; Sünter, I.; Kuuste, H.; Lätt, S.; Voormansik, K.; Noorma, M.

    2014-02-01

    This paper presents a study of a high rate closed-loop spin controller that uses only electromagnetic coils as actuators. The controller is able to perform spin rate control and simultaneously align the spin axis with the Earth's inertial reference frame. It is implemented, optimised and simulated for a 1-unit CubeSat ESTCube-1 to fulfil its mission requirements: spin the satellite up to 360 deg s-1 around the z-axis and align its spin axis with the Earth's polar axis with a pointing error of less than 3°. The attitude of the satellite is determined using a magnetic field vector, a Sun vector and angular velocity. It is estimated using an Unscented Kalman Filter and controlled using three electromagnetic coils. The algorithm is tested in a simulation environment that includes models of space environment and environmental disturbances, sensor and actuator emulation, attitude estimation, and a model to simulate the time delay caused by on-board calculations. In addition to the normal operation mode, analyses of reduced satellite functionality are performed: significant errors of attitude estimation due to non-operational Sun sensors; and limited actuator functionality due to two non-operational coils. A hardware-in-the-loop test is also performed to verify on-board software.

  17. High readmission rate after heart valve surgery

    DEFF Research Database (Denmark)

    Sibilitz, K L; Berg, S K; Thygesen, Lau Caspar;

    2015-01-01

    of anxiety and depression were present in 13.6% and 13.8%, respectively (Hospital Anxiety and Depression Scale score ≥ 8). Twelve months following discharge, 483 persons (56%) were readmitted. Readmission was associated with lower self-reported health (SF-36 PCS: 46.5 vs. 43.9, and MCS 52.2 vs. 50.7). Higher...... after surgery (3.2 (1.2-8.9)) predicted mortality. CONCLUSIONS: 6-12 months after heart valve surgery the readmission rate is high and the self-reported health status is low. Readmission is associated with low self-reported health. Therefore, targeted follow-up strategies post-surgery are needed....

  18. Consideration of wear rates at high velocity

    Science.gov (United States)

    Hale, Chad S.

    The development of the research presented here is one in which high velocity relative sliding motion between two bodies in contact has been considered. Overall, the wear environment is truly three-dimensional. The attempt to characterize three-dimensional wear was not economically feasible because it must be analyzed at the micro-mechanical level to get results. Thus, an engineering approximation was carried out. This approximation was based on a metallographic study identifying the need to include viscoplasticity constitutive material models, coefficient of friction, relationships between the normal load and velocity, and the need to understand wave propagation. A sled test run at the Holloman High Speed Test Track (HHSTT) was considered for the determination of high velocity wear rates. In order to adequately characterize high velocity wear, it was necessary to formulate a numerical model that contained all of the physical events present. The experimental results of a VascoMax 300 maraging steel slipper sliding on an AISI 1080 steel rail during a January 2008 sled test mission were analyzed. During this rocket sled test, the slipper traveled 5,816 meters in 8.14 seconds and reached a maximum velocity of 1,530 m/s. This type of environment was never considered previously in terms of wear evaluation. Each of the features of the metallography were obtained through micro-mechanical experimental techniques. The byproduct of this analysis is that it is now possible to formulate a model that contains viscoplasticity, asperity collisions, temperature and frictional features. Based on the observations of the metallographic analysis, these necessary features have been included in the numerical model, which makes use of a time-dynamic program which follows the movement of a slipper during its experimental test run. The resulting velocity and pressure functions of time have been implemented in the explicit finite element code, ABAQUS. Two-dimensional, plane strain models

  19. Design of 1.5 bit quantization correlator in satellite navigation software receiver

    Institute of Scientific and Technical Information of China (English)

    Hongwei Zhou; Tian Jin; Fangyao L

    2016-01-01

    Currently, 1 bit or 2 bit signal quantization is widely used in satelite navigation software receivers. The bit-wise paralel algorithm has been proposed for 1 bit and 2 bit signal quantization, which performs correlation with high efficiency. In order to improve the performance of the correlator, this paper proposes a new 1.5 bit quantization method. Theoreti-cal analyses are made from the aspects of complexity and quantization loss, and performance comparison between 1.5 bit quantization correlator and traditional correlators is dis-cussed. The results show that the 1.5 bit quantization algo-rithm can save about 30 percent complexity under similar quantization loss, reduce more than 0.5 dB signal noise ratio (SNR) loss under similar complexity. It shows great perform-ance improvement for correlators of satelite navigation soft-ware receivers.

  20. Research and implementation of the burst-mode optical signal bit-error test

    Science.gov (United States)

    Huang, Qiu-yuan; Ma, Chao; Shi, Wei; Chen, Wei

    2009-08-01

    On the basis of the characteristic of TDMA uplink optical signal of PON system, this article puts forward a method of high-speed optical burst bit-error rate testing based on FPGA. The article proposes a new method of generating the burst signal pattern include user-defined pattern and pseudo-random pattern, realizes the slip synchronization, self-synchronization of error detection using data decomposition technique and the traditional irrigation code synchronization technology, completes high-speed burst signal clock synchronization using the rapid synchronization technology of phase-locked loop delay in the external circuit and finishes the bit-error rate test of high-speed burst optical signal.

  1. The architecture design of a 2mW 18-bit high speed weight voltage type DAC based on dual weight resistance chain

    Institute of Scientific and Technical Information of China (English)

    Chen Qixing; Luo Qiyu

    2013-01-01

    At present,the architecture of a digital-to-analog converter (DAC) in essence is based on the weight current,and the average value of its D/A signal current increases in geometric series according to its digital signal bits increase,which is 2n-1 times of its least weight current.But for a dual weight resistance chain type DAC,by using the weight voltage manner to D/A conversion,the D/A signal current is fixed to chain current Icha; it is only 1/2n-1 order of magnitude of the average signal current value of the weight current type DAC.Its principle is:n pairs dual weight resistances form a resistance chain,which ensures the constancy of the chain current; if digital signals control the total weight resistance from the output point to the zero potential point,that could directly control the total weight voltage of the output point,so that the digital signals directly turn into a sum of the weight voltage signals; thus the following goals are realized:(1) the total current is less than 200 μA; (2) the total power consumption is less than 2 mW; (3) an 18-bit conversion can be realized by adopting a multi-grade structure; (4) the chip area is one order of magnitude smaller than the subsection current-steering type DAC; (5) the error depends only on the error of the unit resistance,so it is smaller than the error of the subsection current-steering type DAC;(6) the conversion time is only one action time of switch on or off,so its speed is not lower than the present DAC.

  2. Upgrade Strategy for ALICE at High Rate

    CERN Document Server

    Musa, L

    2012-01-01

    The longterm goal of the ALICE experiment is to provide a precise characterization of the Quark-Gluon Plasma (QGP) state. Such a determination of its properties including initial temperature, degrees of freedom, speed of sound, and in general, transport coefficients would be a major achievement. This would go a long way towards a better understanding of QCD as a genuine multi-particle theory. To achieve this goal, high statistics measurements are required, which will give access also to the very rare physics channels needed to understand the dynamics of this condensed phase of QCD. The general upgrade strategy for the ALICE central barrel is conceived to deal with this challenge with expected Pb-Pb interaction rates of up to 50 kHz, that would provide an accumulated sample of the order of 10 nb^-1 in the period 2019-2023. In this document we sketch the modifications/replacements needed in all ALICE central barrel detectors and online systems (Trigger, DAQ and HLT) for high luminosity running. As the ALICE for...

  3. High Precision Ranging and Range-Rate Measurements over Free-Space-Laser Communication Link

    Science.gov (United States)

    Yang, Guangning; Lu, Wei; Krainak, Michael; Sun, Xiaoli

    2016-01-01

    We present a high-precision ranging and range-rate measurement system via an optical-ranging or combined ranging-communication link. A complete bench-top optical communication system was built. It included a ground terminal and a space terminal. Ranging and range rate tests were conducted in two configurations. In the communication configuration with 622 data rate, we achieved a two-way range-rate error of 2 microns/s, or a modified Allan deviation of 9 x 10 (exp -15) with 10 second averaging time. Ranging and range-rate as a function of Bit Error Rate of the communication link is reported. They are not sensitive to the link error rate. In the single-frequency amplitude modulation mode, we report a two-way range rate error of 0.8 microns/s, or a modified Allan deviation of 2.6 x 10 (exp -15) with 10 second averaging time. We identified the major noise sources in the current system as the transmitter modulation injected noise and receiver electronics generated noise. A new improved system will be constructed to further improve the system performance for both operating modes.

  4. Enhancement of LED indoor communications using OPPM-PWM modulation and grouped bit-flipping decoding.

    Science.gov (United States)

    Yang, Aiying; Li, Xiangming; Jiang, Tao

    2012-04-23

    Combination of overlapping pulse position modulation and pulse width modulation at the transmitter and grouped bit-flipping algorithm for low-density parity-check decoding at the receiver are proposed for visible Light Emitting Diode (LED) indoor communication system in this paper. The results demonstrate that, with the same Photodetector, the bit rate can be increased and the performance of the communication system can be improved by the scheme we proposed. Compared with the standard bit-flipping algorithm, the grouped bit-flipping algorithm can achieve more than 2.0 dB coding gain at bit error rate of 10-5. By optimizing the encoding of overlapping pulse position modulation and pulse width modulation symbol, the performance can be further improved. It is reasonably expected that the bit rate can be upgraded to 400 Mbit/s with a single available LED, thus transmission rate beyond 1 Gbit/s is foreseen by RGB LEDs.

  5. Controlling torque and cutting costs: steerable drill bits deliver in Latin America

    Energy Technology Data Exchange (ETDEWEB)

    Barton, Steve; Garcia, Alexis; Amorim, Dalmo [ReedHycalog, Stonehouse (United Kingdom); Iramina, Wilson [University of Sao Paulo (USP), SP (Brazil); Herrera, Gabriel

    2008-07-01

    Tool face Control is widely regarded as one of the greatest directional drilling challenges with a Fixed Cutter (FC) drill bit on a Steerable Motor assembly. Tool face offset is proportional to the torque generated by the bit, and by nature, FC bits are capable of generating high levels of torque. If large changes in downhole torque are produced while drilling, this will cause rotation of the drill string, and loss of tool face orientation. This results in inefficient drilling and increases risk of bit and downhole tool damage. This paper examines the effect of various FC drill bit components to determine the key design requirements to deliver a smooth torque response and an improved directional performance. Included is a review of the results from comprehensive laboratory testing to determine the effectiveness of a number of different configurations of removable Torque Controlling Components (TCC). These, in combination with specific cutting structure layouts, combine to provide predictable torque response while optimized for high rates of penetration. In addition, unique gauge geometry is disclosed that was engineered to reduce drag and deliver improved borehole quality. This gauge design produces less torque when sliding and beneficial gauge pad interaction with the borehole when in rotating mode. Field performance studies from within Latin America clearly demonstrate that matching TCC, an optimized cutting structure, and gauge geometry to a steerable assembly delivers smooth torque response and improved directional control. Benefits with regard to improved stability are also discussed. Successful application has resulted in significant time and cost savings for the operator, demonstrating that Stability and Steerability improvements can be achieved with an increase in penetration rate. (author)

  6. Classification system adopted for fixed cutter bits

    Energy Technology Data Exchange (ETDEWEB)

    Winters, W.J.; Doiron, H.H.

    1988-01-01

    The drilling industry has begun adopting the 1987 International Association of Drilling Contractors' (IADC) method for classifying fixed cutter drill bits. By studying the classification codes on bit records and properly applying the new IADC fixed cutter dull grading system to recently run bits, the end-user should be able to improve the selection and usage of fixed cutter bits. Several users are developing databases for fixed cutter bits in an effort to relate field performance to some of the more prominent bit design characteristics.

  7. Chaotic laser based physical random bit streaming system with a computer application interface

    Science.gov (United States)

    Shinohara, Susumu; Arai, Kenichi; Davis, Peter; Sunada, Satoshi; Harayama, Takahisa

    2017-03-01

    We demonstrate a random bit streaming system that uses a chaotic laser as its physical entropy source. By performing real-time bit manipulation for bias reduction, we were able to provide the memory of a personal computer with a constant supply of ready-to-use physical random bits at a throughput of up to 4 Gbps. We pay special attention to the end-to-end entropy source model describing how the entropy from physical sources is converted into bit entropy. We confirmed the statistical quality of the generated random bits by revealing the pass rate of the NIST SP800-22 test suite to be 65 % to 75 %, which is commonly considered acceptable for a reliable random bit generator. We also confirmed the stable operation of our random bit steaming system with long-term bias monitoring.

  8. Multi-bit quantum random number generation by measuring positions of arrival photons

    Science.gov (United States)

    Yan, Qiurong; Zhao, Baosheng; Liao, Qinghong; Zhou, Nanrun

    2014-10-01

    We report upon the realization of a novel multi-bit optical quantum random number generator by continuously measuring the arrival positions of photon emitted from a LED using MCP-based WSA photon counting imaging detector. A spatial encoding method is proposed to extract multi-bits random number from the position coordinates of each detected photon. The randomness of bits sequence relies on the intrinsic randomness of the quantum physical processes of photonic emission and subsequent photoelectric conversion. A prototype has been built and the random bit generation rate could reach 8 Mbit/s, with random bit generation efficiency of 16 bits per detected photon. FPGA implementation of Huffman coding is proposed to reduce the bias of raw extracted random bits. The random numbers passed all tests for physical random number generator.

  9. High voltage high repetition rate pulse using Marx topology

    Science.gov (United States)

    Hakki, A.; Kashapov, N.

    2015-06-01

    The paper describes Marx topology using MOSFET transistors. Marx circuit with 10 stages has been done, to obtain pulses about 5.5KV amplitude, and the width of the pulses was about 30μsec with a high repetition rate (PPS > 100), Vdc = 535VDC is the input voltage for supplying the Marx circuit. Two Ferrite ring core transformers were used to control the MOSFET transistors of the Marx circuit (the first transformer to control the charging MOSFET transistors, the second transformer to control the discharging MOSFET transistors).

  10. 湍流大气光通信系统误码率分析与实验研究%Analysis and Experimental Research on Bit Error Rate for Free-Space Optical Communication Systems through Turbulent Atmosphere

    Institute of Scientific and Technical Information of China (English)

    李菲; 吴毅; 侯再红

    2012-01-01

    自由空间光通信(FSO)系统的性能由于受大气湍流影响会产生剧烈波动.根据系统和大气参数评估系统差错性能的研究具有现实意义.以大气湍流信道和光电探测两个模型为基础,建立了FSO系统差错性能的数学仿真模型,提出了湍流条件下系统误码率计算公式.对仿真结果与弱湍流条件下获得的实验数据进行了比较,并依据此模型对光强起伏和背景噪声等因素的影响进行仿真.仿真结果表明,基于该模型的仿真结果与实验数据一致,光强起伏是引起系统性能波动的主要因素,最优判决阈值需根据实际大气条件进行调整.该模型可有效评估湍流条件下FSO系统性能,并为相关理论研究提供参考.%Performance of free-space optical communication (FSO) system fluctuates greatly due to influence by atmospheric turbulence. Research about evaluating system error performance according to parameters of system and atmosphere is a subject of current interest. Based on both optical turbulence channel and photoelectric detection model, a ma thematic simulation model of error performance for FSO system is established, and an expression of bit error rate for FSO system through turbulent atmosphere is proposed. Results of simulation are compared with experimental data obtained under weak turbulence condition and the model is used to characterize factors in turbulence, such as intensity fluctuation and background noise, etc. Simulation results are shown to be consistent with experimental data, intensity fluctuation is a chief factor of system performance fluctuation, and optimized threshold should be adjusted according to pratical atmosphere. The presented model can lead to an efficient performance evaluation and provide reference to correlative theoretical researches.

  11. One bit/s/Hz Spectrally Efficient Transmission for an Eight-Channel NRZ-Modulated DWDM System

    Science.gov (United States)

    Vij, Robin; Sharma, Neeraj

    2016-03-01

    The core of the global telecommunication network consists of wavelength-division multiplexed (WDM) optical transmission systems. WDM is the technology of choice as it allows for a high spectral efficiency. We propose an effective way to counter the nonlinearities like four-wave mixing and cross-phase modulation to achieve the spectral efficiency of 1 bit/s/Hz using non-return-to-zero (NRZ) modulation format. We use the concept of non-uniform channel spacing and non-uniform power assignment between adjacent channels of the WDM system. We have simulated an eight-channel WDM lightwave system with bit rates of 10 and 25 Gbit/s.

  12. HIgh Rate X-ray Fluorescence Detector

    Energy Technology Data Exchange (ETDEWEB)

    Grudberg, Peter Matthew [XIA LLC

    2013-04-30

    The purpose of this project was to develop a compact, modular multi-channel x-ray detector with integrated electronics. This detector, based upon emerging silicon drift detector (SDD) technology, will be capable of high data rate operation superior to the current state of the art offered by high purity germanium (HPGe) detectors, without the need for liquid nitrogen. In addition, by integrating the processing electronics inside the detector housing, the detector performance will be much less affected by the typically noisy electrical environment of a synchrotron hutch, and will also be much more compact than current systems, which can include a detector involving a large LN2 dewar and multiple racks of electronics. The combined detector/processor system is designed to match or exceed the performance and features of currently available detector systems, at a lower cost and with more ease of use due to the small size of the detector. In addition, the detector system is designed to be modular, so a small system might just have one detector module, while a larger system can have many you can start with one detector module, and add more as needs grow and budget allows. The modular nature also serves to simplify repair. In large part, we were successful in achieving our goals. We did develop a very high performance, large area multi-channel SDD detector, packaged with all associated electronics, which is easy to use and requires minimal external support (a simple power supply module and a closed-loop water cooling system). However, we did fall short of some of our stated goals. We had intended to base the detector on modular, large-area detectors from Ketek GmbH in Munich, Germany; however, these were not available in a suitable time frame for this project, so we worked instead with pnDetector GmbH (also located in Munich). They were able to provide a front-end detector module with six 100 m^2 SDD detectors (two monolithic arrays of three elements each) along with

  13. Flexible Bit Preservation on a National Basis

    DEFF Research Database (Denmark)

    Jurik, Bolette; Nielsen, Anders Bo; Zierau, Eld

    2012-01-01

    In this paper we present the results from The Danish National Bit Repository project. The project aim was establishment of a system that can offer flexible and sustainable bit preservation solutions to Danish cultural heritage institutions. Here the bit preservation solutions must include support...... of bit safety as well as other requirements like e.g. confidentiality and availability. The Danish National Bit Repository is motivated by the need to investigate and handle bit preservation for digital cultural heritage. Digital preservation relies on the integrity of the bits which digital material...... consists of, and it is with this focus that the project was initiated. This paper summarizes the requirements for a general system to offer bit preservation to cultural heritage institutions. On this basis the paper describes the resulting flexible system which can support such requirements. The paper...

  14. Cheetah: A high frame rate, high resolution SWIR image camera

    Science.gov (United States)

    Neys, Joel; Bentell, Jonas; O'Grady, Matt; Vermeiren, Jan; Colin, Thierry; Hooylaerts, Peter; Grietens, Bob

    2008-10-01

    A high resolution, high frame rate InGaAs based image sensor and associated camera has been developed. The sensor and the camera are capable of recording and delivering more than 1700 full 640x512pixel frames per second. The FPA utilizes a low lag CTIA current integrator in each pixel, enabling integration times shorter than one microsecond. On-chip logics allows for four different sub windows to be read out simultaneously at even higher rates. The spectral sensitivity of the FPA is situated in the SWIR range [0.9-1.7 μm] and can be further extended into the Visible and NIR range. The Cheetah camera has max 16 GB of on-board memory to store the acquired images and transfer the data over a Gigabit Ethernet connection to the PC. The camera is also equipped with a full CameralinkTM interface to directly stream the data to a frame grabber or dedicated image processing unit. The Cheetah camera is completely under software control.

  15. Annual Report: Support Research for Development of Improved Geothermal Drill Bits

    Energy Technology Data Exchange (ETDEWEB)

    Hendrickson, R.R.; Winzenried, R.W.; Jones, A.H.; Green, S.J.

    1978-07-01

    The work reported herein is a continuation of the program initiated under DOE contract E(10-1)-1546* entitled "Program to Design and Experimentally Test an Improved Geothermal Bit"; the program is now DOE Contract EG-76-C-1546*. The objective of the program has been to accelerate the commercial availability of a tolling cutter drill bit for geothermal applications. Data and experimental tests needed to develop a bit suited to the harsh thermal, abrasive, and chemical environment of the more problematic geothermal wells, including those drilled with air, have been obtained. Efforts were directed at the improvement of both the sealed (lubricated) and unsealed types of bits. The unsealed bit effort included determination of the rationale for materials selection, the selection of steels for the bit body, cutters, and bearings, the selection of tungsten carbide alloys for the friction bearing, and preliminary investigation of optimized tungsten carbide drilling inserts. Bits build** with the new materials were tested under stimulated wellbore conditions. The sealed bit effort provided for the evaluation of candidate high temperature seals and lubricants, utilizing two specially developed test apparatus which simulate the conditions found in a sealed bit operating in a geothermal wellbore. Phase I of the program was devoted largely to (1) the study of the geothermal environment and the failure mechanisms of existing geothermal drill bits, (2) the design and construction of separate facilities for testing both drill-bit seals and full-scale drill bits under simulated geothermal drilling conditions, and (3) fabrication of the MK-I research drill bits from high-temperature steels, and testing in the geothermal drill-bit test facility. The work accomplished in Phase I is reported in References 1 through 9. In Phase II, the first generation experimental bits were tested in the geothermal drill-bit test facility. Test results indicated that hardness retention at temperature

  16. Experimental investigation on the high chip rate of 2D incoherent optical CDMA system

    Science.gov (United States)

    Su, Guorui; Wang, Rong; Pu, Tao; Fang, Tao; Zheng, Jilin; Zhu, Huatao; Wu, Weijiang

    2015-08-01

    An innovative approach to realise high chip rate in OCDMA transmission system is proposed and experimentally investigation, the high chip rate is achieved through a 2-D wavelength-hopping time-spreading en/decoder based on the supercontinuum light source. The source used in the experiment is generated by high nonlinear optical fiber (HNLF), Erbium-doped fiber amplifier (EDFA) which output power is 26 dBm, and distributed feed-back laser diode which works in the gain switch state. The span and the flatness of the light source are 20 nm and 3 dB, respectively, after equalization of wavelength selective switch (WSS). The wavelength-hopping time-spreading coder can be changed 20 nm in the wavelength and 400 ps in the time, is consist of WSS and delay lines. Therefore, the experimental results show that the chip rate can achieve 500 Gchip/s, in the case of 2.5 Gbit/s, while keeping a bit error rate below forward error correction limit after 40 km transmission.

  17. A 10-bit low power SAR A/D converter based on 90 nm CMOS

    Institute of Scientific and Technical Information of China (English)

    Tong Xingyuan; Yang Yintang; Zhu Zhangming; Xiao Yan; Chen Jianming

    2009-01-01

    Traditional and some recently reported low power, high speed and high resolution approaches for SAR A/D converters are discussed. Based on SMIC 65 nm CMOS technology, two typical low power methods reported in previous works are validated by circuit design and simulation. Design challenges and considerations for high speed SAR A/D converters are presented. Moreover, an R-C combination based method is also addressed and a 10-bit SAR A/D converter with this approach is implemented in SMIC 90 nm CMOS process. The DNL and INL are measured to be less than 0.31 LSB and 0.59 LSB respectively. With an input frequency of 420 kHz at 1 MS/s sampling rate, the SFDR and ENOB are measured to be 67.6 dB and 9.46 bits respectively, and the power dissipation is measured to be just 3.17 mW.

  18. A brief review on quantum bit commitment

    Science.gov (United States)

    Almeida, Álvaro J.; Loura, Ricardo; Paunković, Nikola; Silva, Nuno A.; Muga, Nelson J.; Mateus, Paulo; André, Paulo S.; Pinto, Armando N.

    2014-08-01

    In classical cryptography, the bit commitment scheme is one of the most important primitives. We review the state of the art of bit commitment protocols, emphasizing its main achievements and applications. Next, we present a practical quantum bit commitment scheme, whose security relies on current technological limitations, such as the lack of long-term stable quantum memories. We demonstrate the feasibility of our practical quantum bit commitment protocol and that it can be securely implemented with nowadays technology.

  19. A single channel, 6-bit 410-MS/s 3bits/stage asynchronous SAR ADC based on resistive DAC

    Science.gov (United States)

    Xue, Han; Qi, Wei; Huazhong, Yang; Hui, Wang

    2015-05-01

    This paper presents a single channel, low power 6-bit 410-MS/s asynchronous successive approximation register analog-to-digital converter (SAR ADC) for ultrawide bandwidth (UWB) communication, prototyped in a SMIC 65-nm process. Based on the 3 bits/stage structure, resistive DAC, and the modified asynchronous successive approximation register control logic, the proposed ADC attains a peak spurious-free dynamic range (SFDR) of 41.95 dB, and a signal-to-noise and distortion ratio (SNDR) of 28.52 dB for 370 MS/s. At the sampling rate of 410 MS/s, this design still performs well with a 40.71-dB SFDR and 30.02-dB SNDR. A four-input dynamic comparator is designed so as to decrease the power consumption. The measurement results indicate that this SAR ADC consumes 2.03 mW, corresponding to a figure of merit of 189.17 fJ/step at 410 MS/s. Project supported by the National Science Foundation for Young Scientists of China (No. 61306029) and the National High Technology Research and Development Program of China (No. 2013AA014103).

  20. A holistic approach to bit preservation

    DEFF Research Database (Denmark)

    Zierau, Eld

    2012-01-01

    Purpose: The purpose of this paper is to point out the importance of taking a holistic approach to bit preservation when setting out to find an optimal bit preservation solution for specific digital materials. In the last decade there has been an increasing awareness that bit preservation, which ...

  1. Perceptual importance analysis for H.264/AVC bit allocation

    Institute of Scientific and Technical Information of China (English)

    2008-01-01

    The existing H.264/AVC rate control schemes rarely include the perceptual considerations. As a result, the improvements in visual quality are hardly comparable to those in peak signal-to-noise ratio (PSNR). In this paper, we propose a perceptual importance analysis scheme to accurately abstract the spatial and temporal perceptual characteristics of video contents. Then we perform bit allocation at macroblock (MB) level by adopting a perceptual mode decision scheme, which adaptively updates the Lagrangian multiplier for mode decision according to the perceptual importance of each MB. Simulation results show that the proposed scheme can efficiently reduce bit rates without visual quality degradation.

  2. BIT BY BIT: A Game Simulating Natural Language Processing in Computers

    Science.gov (United States)

    Kato, Taichi; Arakawa, Chuichi

    2008-01-01

    BIT BY BIT is an encryption game that is designed to improve students' understanding of natural language processing in computers. Participants encode clear words into binary code using an encryption key and exchange them in the game. BIT BY BIT enables participants who do not understand the concept of binary numbers to perform the process of…

  3. Dispersion Tolerance of 40 Gbaud Multilevel Modulation Formats with up to 3 bits per Symbol

    DEFF Research Database (Denmark)

    Jensen, Jesper Bevensee; Tokle, Torger; Geng, Yan

    2006-01-01

    We present numerical and experimental investigations of dispersion tolerance for multilevel phase- and amplitude modulation with up to 3 bits per symbol at a symbol rate of 40 Gbaud......We present numerical and experimental investigations of dispersion tolerance for multilevel phase- and amplitude modulation with up to 3 bits per symbol at a symbol rate of 40 Gbaud...

  4. The Myth of a High Savings Rate

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    In an attempt to entice consumers to save less and spend more, China has focused on perfecting its social security system, reforming taxation and dividend-sharing proportion between the government and state-owned enterprises. Liu Yuhui, Director of the China Economy Appraisal and Rating Center at the Institute of Finance and Banking, the Chinese Academy of Social Sciences, offered his insights in an Economic Observer article. Edited excerpts follow

  5. Heat Generation During Bone Drilling: A Comparison Between Industrial and Orthopaedic Drill Bits.

    Science.gov (United States)

    Hein, Christopher; Inceoglu, Serkan; Juma, David; Zuckerman, Lee

    2017-02-01

    Cortical bone drilling for preparation of screw placement is common in multiple surgical fields. The heat generated while drilling may reach thresholds high enough to cause osteonecrosis. This can compromise implant stability. Orthopaedic drill bits are several orders more expensive than their similarly sized, publicly available industrial counterparts. We hypothesize that an industrial bit will generate less heat during drilling, and the bits will not generate more heat after multiple cortical passes. We compared 4 4.0 mm orthopaedic and 1 3.97 mm industrial drill bits. Three types of each bit were drilled into porcine femoral cortices 20 times. The temperature of the bone was measured with thermocouple transducers. The heat generated during the first 5 drill cycles for each bit was compared to the last 5 cycles. These data were analyzed with analysis of covariance. The industrial drill bit generated the smallest mean increase in temperature (2.8 ± 0.29°C) P industrial bit generated less heat during drilling than its orthopaedic counterparts. The bits maintained their performance after 20 drill cycles. Consideration should be given by manufacturers to design differences that may contribute to a more efficient cutting bit. Further investigation into the reuse of these drill bits may be warranted, as our data suggest their efficiency is maintained after multiple uses.

  6. The Combustion of HMX. [burning rate at high pressures

    Science.gov (United States)

    Boggs, T. L.; Price, C. F.; Atwood, A. I.; Zurn, D. E.; Eisel, J. L.

    1980-01-01

    The burn rate of HMX was measured at high pressures (p more than 1000 psi). The self deflagration rate of HMX was determined from 1 atmosphere to 50,000 psi. The burning rate shows no significant slope breaks.

  7. A Holistic Approach to Bit Preservation

    DEFF Research Database (Denmark)

    Zierau, Eld Maj-Britt Olmütz

    2011-01-01

    for confidentiality, availability, costs, additional to the requirements of ensuring bit safety. A few examples are: • The way that digital material is represented in files and structures has an influence on whether it is possible to interpret and use the bits at a later stage. Consequentially, the way bits represent....... • There will be requirements for the availability of the bit preserved digital material in order to meet requirements on use of the digital material, e.g. libraries often need to give fast access to preserved digital material to the public, i.e. the availability of the bit preserved material must support the use...

  8. LIQUID ARGON CALORIMETER PERFORMANCE AT HIGH RATES

    CERN Document Server

    Kukhtin, V; The ATLAS collaboration

    2011-01-01

    The performance of the ATLAS liquid argon endcap and forward calorimeters has been projected at the planned high luminosity LHC option HL-LHC by exposing small calorimeter modules of the electromagnetic, hadronic, and forward calorimeters to high intensity proton beams at IHEP/Protvino accelerator. The results of HV current and of pulse shape analysis, and also the dependence of signal amplitude on beam intensity are presented.

  9. Smoking Rates Still High in Some Racial Groups, CDC Reports

    Science.gov (United States)

    ... page: https://medlineplus.gov/news/fullstory_160256.html Smoking Rates Still High in Some Racial Groups, CDC ... lot of progress in getting Americans to stop smoking, some groups still have high smoking rates, a ...

  10. New measuring techniques in the drill bit for recording of the full-face cutting rate and consolidation of the roadway sides in the drill bit area; Neue Messverfahren im Bohrkopf zur Erfassung des Vollschnittmaschinenvortriebs und Konsolidierung der Streckenstoesse im Bohrkopfbereich

    Energy Technology Data Exchange (ETDEWEB)

    Kuehnemann, D.

    1990-10-01

    The safety of full-face cutting machines has to be assured also in greater depths. In addition, one wants to attain information about the rock conditions as early as possible in the case of occurring faults. For this reason, new systems were to be developed for monitoring of full-face cutting machines. Numerous measuring systems and monitoring systems were used and examined within the framework of the project works. It soon turned out that new systems had to be developed and tested for precise monitoring. Flexible microprocessor systems, sensors and actuators were developed and tested for the respective specific case of application. After several years of development work a new system was developed, which is continuous and transparently from the drill bit area to the surface area. Excavations in the drill bit area are recognized already immediately behind the drift face. Position and quantity of the excavations are transmitted and processed to a central microprocessor by underground ultrasonic sensors. With the aid of specific technologies and newly developed building materials, these excavations are already consolidated and/or saved in the drill bit in front of the dust shield. The cutting rolls are monitored above ground, and the position of the full-face cutting machine is specified above ground. The automatic control via a laser sensor system is also carried out from above ground. In addition to control and monitoring, all other relevant parameters are transmitted from the underground machine to the surface, where they are indicated and recorded. With the technical data which are available in the computer, the data required for optimal heading are determined and transmitted to the control elements of the microprocessors. (orig./HS). [Deutsch] Um die Sicherheit bei Vollschnittmaschinen mit dem Vordringen in groessere Teufen zu gewaehrleisten und um moeglichst fruehe Kenntnisse der vorhandenen Gebirgsverhaeltnisse bei auftretenden Stoerungen zu erlangen waren

  11. BitPredator: A Discovery Algorithm for BitTorrent Initial Seeders and Peers

    Energy Technology Data Exchange (ETDEWEB)

    Borges, Raymond [West Virginia University; Patton, Robert M [ORNL; Kettani, Houssain [Polytechnic University of Puerto Rico (PUPR); Masalmah, Yahya [Universidad del Turabo

    2011-01-01

    There is a large amount of illegal content being replicated through peer-to-peer (P2P) networks where BitTorrent is dominant; therefore, a framework to profile and police it is needed. The goal of this work is to explore the behavior of initial seeds and highly active peers to develop techniques to correctly identify them. We intend to establish a new methodology and software framework for profiling BitTorrent peers. This involves three steps: crawling torrent indexers for keywords in recently added torrents using Really Simple Syndication protocol (RSS), querying torrent trackers for peer list data and verifying Internet Protocol (IP) addresses from peer lists. We verify IPs using active monitoring methods. Peer behavior is evaluated and modeled using bitfield message responses. We also design a tool to profile worldwide file distribution by mapping IP-to-geolocation and linking to WHOIS server information in Google Earth.

  12. High frame rate imaging based photometry

    DEFF Research Database (Denmark)

    Harpsøe, Kennet Bomann West; Jørgensen, U. G.; Andersen, M. I.;

    2012-01-01

    in conventional CCDs, and new methods for handling these must be developed. We aim to investigate how the normal photometric reduction steps from conventional CCDs should be adjusted to be applicable to EMCCD data. One complication is that a bias frame cannot be obtained conventionally, as the output from...... an EMCCD is not normally distributed. Also, the readout process generates spurious charges in any CCD, but in EMCCD data, these charges are visible as opposed to the conventional CCD. Furthermore we aim to eliminate the photon waste associated with lucky imaging by combining this method with shift......-and-add. A simple probabilistic model for the dark output of an EMCCD is developed. Fitting this model with the expectation-maximization algorithm allows us to estimate the bias, readout noise, amplification, and spurious charge rate per pixel and thus correct for these phenomena. To investigate the stability...

  13. High Count Rate Electron Probe Microanalysis

    Science.gov (United States)

    Geller, Joseph D.; Herrington, Charles

    2002-01-01

    Reducing the measurement uncertainty of quantitative analyses made using electron probe microanalyzers (EPMA) requires a careful study of the individual uncertainties from each definable step of the measurement. Those steps include measuring the incident electron beam current and voltage, knowing the angle between the electron beam and the sample (takeoff angle), collecting the emitted x rays from the sample, comparing the emitted x-ray flux to known standards (to determine the k-ratio) and transformation of the k-ratio to concentration using algorithms which includes, as a minimum, the atomic number, absorption, and fluorescence corrections. This paper discusses the collection and counting of the emitted x rays, which are diffracted into the gas flow or sealed proportional x-ray detectors. The representation of the uncertainty in the number of collected x rays collected reduces as the number of counts increase. The uncertainty of the collected signal is fully described by Poisson statistics. Increasing the number of x rays collected involves either counting longer or at a higher counting rate. Counting longer means the analysis time increases and may become excessive to get to the desired uncertainty. Instrument drift also becomes an issue. Counting at higher rates has its limitations, which are a function of the detector physics and the detecting electronics. Since the beginning of EPMA analysis, analog electronics have been used to amplify and discriminate the x-ray induced ionizations within the proportional counter. This paper will discuss the use of digital electronics for this purpose. These electronics are similar to that used for energy dispersive analysis of x rays with either Si(Li) or Ge(Li) detectors except that the shaping time constants are much smaller. PMID:27446749

  14. High pressure, high strain rate material strength studies

    Science.gov (United States)

    Remington, B. A.; Arsenlis, A.; Barton, N.; Belof, J.; Cavallo, R.; Maddox, B.; Park, H.-S.; Prisbrey, S.; Rudd, R.; Comley, A.; Meyers, M.; Wark, J.

    2011-10-01

    Constitutive models for material strength are currently being tested at high pressures by comparing 2D simulations with experiments measuring the Rayleigh-Taylor (RT) instability evolution in solid-state samples of vanadium (V), tantalum (Ta), and iron (Fe). The multiscale strength models being tested combine molecular dynamics, dislocation dynamics, and continuum simulations. Our analysis for the V experiments suggests that the material deformation at these conditions falls into the phonon drag regime, whereas for Ta, the deformation resides mainly in the thermal activation regime. Recent Fe-RT experiments suggest perturbation growth about the alpha-epsilon (bcc-hcp) phase transition threshold has been observed. Using the LLNL multiscale models, we decompose the strength as a function of strain rate into its dominant components of thermal activation, phonon drag, and work hardening. We have also developed a dynamic diffraction diagnostic technique to measure strength directly from shock compressed single crystal samples. Finally, recovery experiments allow a comparison of residual dislocation density with predictions from the multiscale model. This work performed under the auspices of the U.S. DoE by LLNL Security, LLC under Contract DE-AC52-07NA27344.

  15. High-Rate Capable Floating Strip Micromegas

    CERN Document Server

    Bortfeldt, Jonathan; Biebel, Otmar; Danger, Helge; Flierl, Bernhard; Hertenberger, Ralf; Lösel, Philipp; Moll, Samuel; Parodi, Katia; Rinaldi, Ilaria; Ruschke, Alexander; Zibell, André

    2015-01-01

    We report on the optimization of discharge insensitive floating strip Micromegas (MICRO-MEsh GASeous) detectors, fit for use in high-energy muon spectrometers. The suitability of these detectors for particle tracking is shown in high-background environments and at very high particle fluxes up to 60MHz/cm$^2$. Measurement and simulation of the microscopic discharge behavior have demonstrated the excellent discharge tolerance. A floating strip Micromegas with an active area of 48cm$\\times$50cm with 1920 copper anode strips exhibits in 120GeV pion beams a spatial resolution of 50$\\mu$m at detection efficiencies above 95%. Pulse height, spatial resolution and detection efficiency are homogeneous over the detector. Reconstruction of particle track inclination in a single detector plane is discussed, optimum angular resolutions below $5^\\circ$ are observed. Systematic deviations of this $\\mu$TPC-method are fully understood. The reconstruction capabilities for minimum ionizing muons are investigated in a 6.4cm$\\time...

  16. High dose rate brachytherapy source measurement intercomparison.

    Science.gov (United States)

    Poder, Joel; Smith, Ryan L; Shelton, Nikki; Whitaker, May; Butler, Duncan; Haworth, Annette

    2017-06-01

    This work presents a comparison of air kerma rate (AKR) measurements performed by multiple radiotherapy centres for a single HDR (192)Ir source. Two separate groups (consisting of 15 centres) performed AKR measurements at one of two host centres in Australia. Each group travelled to one of the host centres and measured the AKR of a single (192)Ir source using their own equipment and local protocols. Results were compared to the (192)Ir source calibration certificate provided by the manufacturer by means of a ratio of measured to certified AKR. The comparisons showed remarkably consistent results with the maximum deviation in measurement from the decay-corrected source certificate value being 1.1%. The maximum percentage difference between any two measurements was less than 2%. The comparisons demonstrated the consistency of well-chambers used for (192)Ir AKR measurements in Australia, despite the lack of a local calibration service, and served as a valuable focal point for the exchange of ideas and dosimetry methods.

  17. Bit threads and holographic entanglement

    CERN Document Server

    Freedman, Michael

    2016-01-01

    The Ryu-Takayanagi (RT) formula relates the entanglement entropy of a region in a holographic theory to the area of a corresponding bulk minimal surface. Using the max flow-min cut principle, a theorem from network theory, we rewrite the RT formula in a way that does not make reference to the minimal surface. Instead, we invoke the notion of a "flow", defined as a divergenceless norm-bounded vector field, or equivalently a set of Planck-thickness "bit threads". The entanglement entropy of a boundary region is given by the maximum flux out of it of any flow, or equivalently the maximum number of bit threads that can emanate from it. The threads thus represent entanglement between points on the boundary, and naturally implement the holographic principle. As we explain, this new picture clarifies several conceptual puzzles surrounding the RT formula. We give flow-based proofs of strong subadditivity and related properties; unlike the ones based on minimal surfaces, these proofs correspond in a transparent manner...

  18. Mourning in Bits and Stone

    DEFF Research Database (Denmark)

    Sabra, Jakob Borrits

    We mourn our dead, publicly and privately, online and offline. Cemeteries, web memorials and social network sites make up parts of todays intricately weaved and interrelated network of death, grief and memorialization practices [1]–[5]. Whether cut in stone or made of bits, graves, cemeteries, me...... and memorialization by discussing the publicly and privately digital and social death from a spatial, temporal, physical and digital angle. Further the paper will reflect on how to encompass shifting trends and technologies in ‘traditional’ spaces of mourning and remembrance.......We mourn our dead, publicly and privately, online and offline. Cemeteries, web memorials and social network sites make up parts of todays intricately weaved and interrelated network of death, grief and memorialization practices [1]–[5]. Whether cut in stone or made of bits, graves, cemeteries......, memorials, monuments, websites and social networking services (SNS) all are alterable, controllable and adaptive. They represent a certain rationale contrary to the emotive state of mourning (e.g. gravesites function as both spaces of internment and places of spiritual and emotional recollection). Following...

  19. Bit Threads and Holographic Entanglement

    Science.gov (United States)

    Freedman, Michael; Headrick, Matthew

    2016-11-01

    The Ryu-Takayanagi (RT) formula relates the entanglement entropy of a region in a holographic theory to the area of a corresponding bulk minimal surface. Using the max flow-min cut principle, a theorem from network theory, we rewrite the RT formula in a way that does not make reference to the minimal surface. Instead, we invoke the notion of a "flow", defined as a divergenceless norm-bounded vector field, or equivalently a set of Planck-thickness "bit threads". The entanglement entropy of a boundary region is given by the maximum flux out of it of any flow, or equivalently the maximum number of bit threads that can emanate from it. The threads thus represent entanglement between points on the boundary, and naturally implement the holographic principle. As we explain, this new picture clarifies several conceptual puzzles surrounding the RT formula. We give flow-based proofs of strong subadditivity and related properties; unlike the ones based on minimal surfaces, these proofs correspond in a transparent manner to the properties' information-theoretic meanings. We also briefly discuss certain technical advantages that the flows offer over minimal surfaces. In a mathematical appendix, we review the max flow-min cut theorem on networks and on Riemannian manifolds, and prove in the network case that the set of max flows varies Lipshitz continuously in the network parameters.

  20. A Simple and High Performing Rate Control Initialization Method for H.264 AVC Coding Based on Motion Vector Map and Spatial Complexity at Low Bitrate

    Directory of Open Access Journals (Sweden)

    Yalin Wu

    2014-01-01

    Full Text Available The temporal complexity of video sequences can be characterized by motion vector map which consists of motion vectors of each macroblock (MB. In order to obtain the optimal initial QP (quantization parameter for the various video sequences which have different spatial and temporal complexities, this paper proposes a simple and high performance initial QP determining method based on motion vector map and temporal complexity to decide an initial QP in given target bit rate. The proposed algorithm produces the reconstructed video sequences with outstanding and stable quality. For any video sequences, the initial QP can be easily determined from matrices by target bit rate and mapped spatial complexity using proposed mapping method. Experimental results show that the proposed algorithm can show more outstanding objective and subjective performance than other conventional determining methods.

  1. Liquid argon calorimeter performance at high rates

    CERN Document Server

    Seifert, F; The ATLAS collaboration

    2012-01-01

    The expected increase of luminosity at HL-LHC by a factor of ten with respect to LHC luminosities has serious consequences for the signal reconstruction, radiation hardness requirements and operations of the ATLAS liquid argon calorimeters in the endcap, respectively forward region. Small modules of each type of calorimeter have been built and exposed to a high intensity proton beam of 50 GeV at IHEP/Protvino. The beam is extracted via the bent crystal technique, offering the unique opportunity to cover intensities ranging from $10^6$ p/s up to $10^{12}$ p/s. This exceeds the deposited energy per time expected at HL-LHC by more than a factor of 100. The correlation between beam intensity and the read-out signal has been studied. The data show clear indications of pulse shape distortion due to the high ionization build-up, in agreement with MC expectations. This is also confirmed from the dependence of the HV currents on beam intensity.

  2. Liquid Argon Calorimeter performance at High Rates

    CERN Document Server

    Seifert, F; The ATLAS collaboration

    2013-01-01

    The expected increase of luminosity at HL-LHC by a factor of ten with respect to LHC luminosities has serious consequences for the signal reconstruction, radiation hardness requirements and operations of the ATLAS liquid argon calorimeters in the endcap, respectively forward region. Small modules of each type of calorimeter have been built and exposed to a high intensity proton beam of 50 GeV at IHEP/Protvino. The beam is extracted via the bent crystal technique, offering the unique opportunity to cover intensities ranging from $10^6$ p/s up to $3\\cdot10^{11}$ p/s. This exceeds the deposited energy per time expected at HL-LHC by more than a factor of 100. The correlation between beam intensity and the read-out signal has been studied. The data show clear indications of pulse shape distortion due to the high ionization build-up, in agreement with MC expectations. This is also confirmed from the dependence of the HV currents on beam intensity.

  3. High-deposition-rate ceramics synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Allendorf, M.D.; Osterheld, T.H.; Outka, D.A. [Sandia National Laboratories, Livermore, CA (United States)] [and others

    1995-05-01

    Parallel experimental and computational investigations are conducted in this project to develop validated numerical models of ceramic synthesis processes. Experiments are conducted in the High-Temperature Materials Synthesis Laboratory in Sandia`s Combustion Research Facility. A high-temperature flow reactor that can accommodate small preforms (1-3 cm diameter) generates conditions under which deposition can be observed, with flexibility to vary both deposition temperature (up to 1500 K) and pressure (as low as 10 torr). Both mass spectrometric and laser diagnostic probes are available to provide measurements of gas-phase compositions. Experiments using surface analytical techniques are also applied to characterize important processes occuring on the deposit surface. Computational tools developed through extensive research in the combustion field are employed to simulate the chemically reacting flows present in typical industrial reactors. These include the CHEMKIN and Surface-CHEMKIN suites of codes, which permit facile development of complex reaction mechanisms and vastly simplify the implementation of multi-component transport and thermodynamics. Quantum chemistry codes are also used to estimate thermodynamic and kinetic data for species and reactions for which this information is unavailable.

  4. High rate fabrication of compression molded components

    Energy Technology Data Exchange (ETDEWEB)

    Matsen, Marc R.; Negley, Mark A.; Dykstra, William C.; Smith, Glen L.; Miller, Robert J.

    2016-04-19

    A method for fabricating a thermoplastic composite component comprises inductively heating a thermoplastic pre-form with a first induction coil by inducing current to flow in susceptor wires disposed throughout the pre-form, inductively heating smart susceptors in a molding tool to a leveling temperature with a second induction coil by applying a high-strength magnetic field having a magnetic flux that passes through surfaces of the smart susceptors, shaping the magnetic flux that passes through surfaces of the smart susceptors to flow substantially parallel to a molding surface of the smart susceptors, placing the heated pre-form between the heated smart susceptors; and applying molding pressure to the pre-form to form the composite component.

  5. The modern high rate digital cassette recorder

    Science.gov (United States)

    Clemow, Martin

    1993-01-01

    The magnetic tape recorder has played an essential role in the capture and storage of instrumentation data for more than thirty years. During this time, data recording technology has steadily progressed to meet user demands for more channels, wider bandwidths, and longer recording durations. When acquisition and processing moved from analog to digital techniques, so recorder design followed suit. Milestones marking the evolution of the data recorder through these various stages - multi-track analog, high density longitudinal digital, and more recently rotary digital - have often represented important breakthroughs in the handling of ever-greater quantities of data. Throughout this period there has been a very clear line of demarcation between data storage methods in the 'instrumentation world' on the one hand and the 'computer peripheral world' on the other. This is despite the fact that instrumentation data, whether analog or digital at the point of acquisition, is now likely to be processed on a digital computer at some stage. Regardless of whether the processing device is a small personal computer, a workstation, or the largest supercomputer, system integrators have traditionally been faced with the same basic problem - how to interface what is essentially a manually controlled, continuously running device (the tape recorder) into the fast start/stop computer environment without resorting to an excessive amount of complex custom interfacing and performance compromise. The increasing availability of affordable high power processing equipment throughout the scientific world is forcing recorder manufacturers to make their latest and perhaps most important breakthrough - the computer-friendly data recorder. The operating characteristics of such recorders are discussed and the resultant impact on both data acquisition and data analysis elements of system configuration are considered.

  6. Video coding bit allocation algorithm over wireless transmission channel

    Institute of Scientific and Technical Information of China (English)

    ZHANG Wei; ZHOU Yuan-hua

    2006-01-01

    For two-way video communications over wireless channels using the automatic repeat request (ARQ) retransmission scheme, TMN8 rate control scheme is not effective in minimizing the number of frames skipped and cannot guarantee video quality during the retransmissions of error packets. This paper presents a joint source channel bit allocation scheme that allocates target bits according to encoder buffer fullness and estimation of channel condition by retransmission information. The results obtained from implementing our scheme in H. 263 + coder over wireless channel model show that our proposed scheme encodes the video sequences with lower and steadier buffer delay, fewer frames skipped and higher average PSNR compared to TMN8.

  7. A 14-bit 50 MS/s sample-and-hold circuit for pipelined ADC

    Science.gov (United States)

    Sen, Yue; Yiqiang, Zhao; Ruilong, Pang; Yun, Sheng

    2014-05-01

    A high performance sample-and-hold (S/H) circuit used in a pipelined analog-to-digital converter (ADC) is presented. Capacitor flip-around architecture is used in this S/H circuit with a novel gain-boosted differential folded cascode operational transconductance amplifier. A double-bootstrapped switch is designed to improve the performance of the circuit. The circuit is implemented using a 0.18 μm 1P6M CMOS process. Measurement results show that the effective number of bits is 14.03 bits, the spurious free dynamic range is 94.62 dB, the signal to noise and distortion ratio is 86.28 dB, and the total harmonic distortion is -91:84 dB for a 5 MHz input signal with 50 MS/s sampling rate. A pipeline ADC with the designed S/H circuit has been implemented.

  8. High data rate optical transceiver terminal

    Science.gov (United States)

    Clarke, E. S.

    1973-01-01

    The objectives of this study were: (1) to design a 400 Mbps optical transceiver terminal to operate from a high-altitude balloon-borne platform in order to permit the quantitative evaluation of a space-qualifiable optical communications system design, (2) to design an atmospheric propagation experiment to operate in conjunction with the terminal to measure the degrading effects of the atmosphere on the links, and (3) to design typical optical communications experiments for space-borne laboratories in the 1980-1990 time frame. As a result of the study, a transceiver package has been configured for demonstration flights during late 1974. The transceiver contains a 400 Mbps transmitter, a 400 Mbps receiver, and acquisition and tracking receivers. The transmitter is a Nd:YAG, 200 Mhz, mode-locked, CW, diode-pumped laser operating at 1.06 um requiring 50 mW for 6 db margin. It will be designed to implement Pulse Quaternary Modulation (PQM). The 400 Mbps receiver utilizes a Dynamic Crossed-Field Photomultiplier (DCFP) detector. The acquisition receiver is a Quadrant Photomultiplier Tube (QPMT) and receives a 400 Mbps signal chopped at 0.1 Mhz.

  9. The Effect of Minimum Wage Rates on High School Completion

    Science.gov (United States)

    Warren, John Robert; Hamrock, Caitlin

    2010-01-01

    Does increasing the minimum wage reduce the high school completion rate? Previous research has suffered from (1. narrow time horizons, (2. potentially inadequate measures of states' high school completion rates, and (3. potentially inadequate measures of minimum wage rates. Overcoming each of these limitations, we analyze the impact of changes in…

  10. In bits, bytes and stone

    DEFF Research Database (Denmark)

    Sabra, Jakob Borrits; Andersen, Hans Jørgen

    The digital spheres of Information and Communication Technologies (ICT) and Social Network Services (SNS) are influencing 21st. century death. Today the dying and the bereaved attend mourning and remembrance both online and offline. Combined, the cemeteries, web memorials and social network sites...... designs'. Urns, coffins, graves, cemeteries, memorials, monuments, websites, applications and software services, whether cut in stone or made of bits, are all influenced by discourses of publics, economics, power, technology and culture. Designers, programmers, stakeholders and potential end-users often...... do not recognize the need or potential of working with or using, specific 'death-services/products', since they find little or no comfort in contemplating, working or playing around with the concept of death and its life changing consequences. Especially not while being alive and well...

  11. FastBit Reference Manual

    Energy Technology Data Exchange (ETDEWEB)

    Wu, Kesheng

    2007-08-02

    An index in a database system is a data structure that utilizes redundant information about the base data to speed up common searching and retrieval operations. Most commonly used indexes are variants of B-trees, such as B+-tree and B*-tree. FastBit implements a set of alternative indexes call compressed bitmap indexes. Compared with B-tree variants, these indexes provide very efficient searching and retrieval operations by sacrificing the efficiency of updating the indexes after the modification of an individual record. In addition to the well-known strengths of bitmap indexes, FastBit has a special strength stemming from the bitmap compression scheme used. The compression method is called the Word-Aligned Hybrid (WAH) code. It reduces the bitmap indexes to reasonable sizes and at the same time allows very efficient bitwise logical operations directly on the compressed bitmaps. Compared with the well-known compression methods such as LZ77 and Byte-aligned Bitmap code (BBC), WAH sacrifices some space efficiency for a significant improvement in operational efficiency. Since the bitwise logical operations are the most important operations needed to answer queries, using WAH compression has been shown to answer queries significantly faster than using other compression schemes. Theoretical analyses showed that WAH compressed bitmap indexes are optimal for one-dimensional range queries. Only the most efficient indexing schemes such as B+-tree and B*-tree have this optimality property. However, bitmap indexes are superior because they can efficiently answer multi-dimensional range queries by combining the answers to one-dimensional queries.

  12. Bit and Power Loading Approach for Broadband Multi-Antenna OFDM System

    DEFF Research Database (Denmark)

    Rahman, Muhammad Imadur; Das, Suvra S.; Wang, Yuanye

    2007-01-01

    In this work, we have studied bit and power allocation strategies for multi-antenna assisted Orthogonal Frequency Division Multiplexing (OFDM) systems and investigated the impact of different rates of bit and power allocations on various multi-antenna diversity schemes. It is observed that, if we...... allocations across OFDM sub-channels are required together for efficient exploitation of wireless channel....

  13. Bit-coded regular expression parsing

    DEFF Research Database (Denmark)

    Nielsen, Lasse; Henglein, Fritz

    2011-01-01

    Regular expression parsing is the problem of producing a parse tree of a string for a given regular expression. We show that a compact bit representation of a parse tree can be produced efficiently, in time linear in the product of input string size and regular expression size, by simplifying...... the DFA-based parsing algorithm due to Dub ´e and Feeley to emit the bits of the bit representation without explicitly materializing the parse tree itself. We furthermore show that Frisch and Cardelli’s greedy regular expression parsing algorithm can be straightforwardly modified to produce bit codings...

  14. High regression rate, high density hybrid fuels Project

    Data.gov (United States)

    National Aeronautics and Space Administration — This SBIR program will investigate high energy density novel nanofuels combined with high density binders for use with an N2O oxidizer. Terves has developed...

  15. A 1.5 bit/s Pipelined Analog-to-Digital Converter Design with Independency of Capacitor Mismatch

    Institute of Scientific and Technical Information of China (English)

    LI Dan; RONG Men-tian; MAO Jun-fa

    2007-01-01

    A new technique which is named charge temporary storage technique (CTST) was presented to improve the linearity of a 1.5 bit/s pipelined analog-to-digital converter (ADC).The residual voltage was obtained from the sampling capacitor, and the other capacitor was just a temporary storage of charge.Then, the linearity produced by the mismatch of these capacitors was eliminated without adding extra capacitor error-averaging amplifiers.The simulation results confirmed the high linearity and low dissipation of pipelined ADCs implemented in CTST, so CTST was a new method to implement high resolution, small size ADCs.

  16. Strain rate effect in high-speed wire drawing process

    Science.gov (United States)

    He, S.; Van Houtte, P.; Van Bael, A.; Mei, F.; Sarban, A.; Boesman, P.; Galvez, F.; Atienza, J. M.

    2002-05-01

    This paper presents a study on the strain rate effect during high-speed wire drawing process by means of finite element simulation. Based on the quasistatic stresses obtained by normal tensile tests and dynamic stresses at high strain rates by split Hopkinson pressure bar tests, the wire drawing process was simulated for low carbon steel and high carbon steel. The results show that both the deformation process and the final properties of drawn wires are influenced by the strain rate.

  17. High-Rate Strong-Signal Quantum Cryptography

    Science.gov (United States)

    Yuen, Horace P.

    1996-01-01

    Several quantum cryptosystems utilizing different kinds of nonclassical lights, which can accommodate high intensity fields and high data rate, are described. However, they are all sensitive to loss and both the high rate and the strong-signal character rapidly disappear. A squeezed light homodyne detection scheme is proposed which, with present-day technology, leads to more than two orders of magnitude data rate improvement over other current experimental systems for moderate loss.

  18. An improved EZBC algorithm based on block bit length

    Science.gov (United States)

    Wang, Renlong; Ruan, Shuangchen; Liu, Chengxiang; Wang, Wenda; Zhang, Li

    2011-12-01

    Embedded ZeroBlock Coding and context modeling (EZBC) algorithm has high compression performance. However, it consumes large amounts of memory space because an Amplitude Quadtree of wavelet coefficients and other two link lists would be built during the encoding process. This is one of the big challenges for EZBC to be used in real time or hardware applications. An improved EZBC algorithm based on bit length of coefficients was brought forward in this article. It uses Bit Length Quadtree to complete the coding process and output the context for Arithmetic Coder. It can achieve the same compression performance as EZBC and save more than 75% memory space required in the encoding process. As Bit Length Quadtree can quickly locate the wavelet coefficients and judge their significance, the improved algorithm can dramatically accelerate the encoding speed. These improvements are also beneficial for hardware. PACS: 42.30.Va, 42.30.Wb

  19. Hanford coring bit temperature monitor development testing results report

    Energy Technology Data Exchange (ETDEWEB)

    Rey, D.

    1995-05-01

    Instrumentation which directly monitors the temperature of a coring bit used to retrieve core samples of high level nuclear waste stored in tanks at Hanford was developed at Sandia National Laboratories. Monitoring the temperature of the coring bit is desired to enhance the safety of the coring operations. A unique application of mature technologies was used to accomplish the measurement. This report documents the results of development testing performed at Sandia to assure the instrumentation will withstand the severe environments present in the waste tanks.

  20. An ultra high-speed 8-bit timing interleave folding & interpolating analog-to-digital converter with digital foreground calibration technology

    Institute of Scientific and Technical Information of China (English)

    Zhang Zhengping; Wang Yonglu; Huang Xingfa; Shen Xiaofeng; Zhu Can; Zhang Lei; Yu Jinshan; Zhang Ruitao

    2011-01-01

    A 2-Gsample/s 8-b analog-to-digital converter in 0.35μm BiCMOS process technology is presented.The ADC uses the unique folding and interpolating algorithm and dual-channel timing interleave multiplexing technology to achieve a sampling rate of 2 GSPS.Digital calibration technology is used for the offset and gain corrections of the S/H circuit,the offset correction of preamplifier,and the gain and clock phase corrections between channels.As a result of testing,the ADC achieves 7.32 ENOB at an analog input of 484 MHz and 7.1 ENOB at Nyquist input after the chip is self-corrected.

  1. Fpga Implementation of 8-Bit Vedic Multiplier by Using Complex Numbers

    Directory of Open Access Journals (Sweden)

    Gundlapalle Nandakishore,

    2014-06-01

    Full Text Available The paper describes the implementation of 8-bit vedic multiplier using complex numbers previous technique describes that 8-bit vedic multiplier using barrel shifter by FPGA implementation comparing the both technique in this paper propagation delay is reduced so that processing of speed will be high 8-bit vedic multiplier using barrel shifter propagation delay nearly 22nsec but present technique 8-bit vedic multiplier using complex numbers where propagation delay is 19nsec. The design is implemented and verified by FPGA and ISE simulator. The core was implemented on the Spartan 3E starts board the preferred language is used in verilog.

  2. Fracto-mechanoluminescent light emission of EuD4TEA-PDMS composites subjected to high strain-rate compressive loading

    Science.gov (United States)

    Ryu, Donghyeon; Castaño, Nicolas; Bhakta, Raj; Kimberley, Jamie

    2017-08-01

    The objective of this study is to understand light emission characteristics of fracto-mechanoluminescent (FML) europium tetrakis(dibenzoylmethide)-triethylammonium (EuD4TEA) crystals under high strain-rate compressive loading. As a sensing material that can play a pivotal role for the self-powered impact sensor technology, it is important to understand transformative light emission characteristics of the FML EuD4TEA crystals under high strain-rate compressive loading. First, EuD4TEA crystals were synthesized and embedded into polydimethylsiloxane (PDMS) elastomer to fabricate EuD4TEA-PDMS composite test specimens. Second, the prepared EuD4TEA-PDMS composites were tested using the modified Kolsky bar setup equipped with a high-speed camera. Third, FML light emission was captured to yield 12 bit grayscale video footage, which was processed to quantify the FML light emission. Finally, quantitative parameters were generated by taking into account pixel values and population of pixels of the 12 bit grayscale images to represent FML light intensity. The FML light intensity was correlated with high strain-rate compressive strain and strain rate to understand the FML light emission characteristics under high strain-rate compressive loading that can result from impact occurrences.

  3. A family of compatible single- and multimicroprocessor systems with 8-bit and 16-bit Microprocessors

    Energy Technology Data Exchange (ETDEWEB)

    Brzezinski, J.; Cellary, W.; Kreglewski, J.

    1984-10-01

    In the paper, a multimicroprocessor system for 8-bit and 16-bit microprocessors is presented. The main assumptions of the project of the presented system are discussed. Different single- and multimicroprocessor structures with 8-bit microprocessors are outlined. A detailed description of two single-board microcomputers and system aspects of different solutions are presented. Finally, an intelligent floppy disk controller is described.

  4. High Blood Pressure Rates Have Doubled Worldwide Since 1975

    Science.gov (United States)

    ... https://medlineplus.gov/news/fullstory_162069.html High Blood Pressure Rates Have Doubled Worldwide Since 1975 Most of ... News) -- The number of people worldwide with high blood pressure has nearly doubled over the past 40 years, ...

  5. High-Data-Rate Quadrax Cable Microwave Characterization at the NASA Glenn Structural Dynamics Laboratory

    Science.gov (United States)

    Theofylaktos, Onoufrios; Warner, Joseph D.; Sheehe, Charles J.

    2012-01-01

    An experiment was performed to determine the degradation in the bit-error-rate (BER) in the high-data-rate cables chosen for the Orion Service Module due to extreme launch conditions of vibrations with a magnitude of 60g. The cable type chosen for the Orion Service Module was no. 8 quadrax cable. The increase in electrical noise induced on these no. 8 quadrax cables was measured at the NASA Glenn vibration facility in the Structural Dynamics Laboratory. The intensity of the vibrations was set at 32g, which was the maximum available level at the facility. The cable lengths used during measurements were 1, 4, and 8 m. The noise measurements were done in an analog fashion using a performance network analyzer (PNA) by recording the standard deviation of the transmission scattering parameter S(sub 21) over the frequency range of 100 to 900 MHz. The standard deviation of S(sub 210 was measured before, during, and after the vibration of the cables at the vibration facility. We observed an increase in noise by a factor of 2 to 6. From these measurements we estimated the increase expected in the BER for a cable length of 25 m and concluded that these findings are large enough that the noise increase due to vibration must be taken in to account for the design of the communication system for a BER of 10(exp -8).

  6. High-shear-rate capillary viscometer for inkjet inks

    Energy Technology Data Exchange (ETDEWEB)

    Wang Xi [FUJIFILM Dimatix, Inc., Lebanon, New Hampshire 03766 (United States); Carr, Wallace W.; Bucknall, David G. [School of Polymer, Textile, and Fiber Engineering, Georgia Institute of Technology, Atlanta, Georgia 30332 (United States); Morris, Jeffrey F. [Department of Chemical Engineering and Benjamin Levich Institute for Physico-Chemical Hydrodynamics, City College of New York, New York, New York 10031 (United States)

    2010-06-15

    A capillary viscometer developed to measure the apparent shear viscosity of inkjet inks at high apparent shear rates encountered during inkjet printing is described. By using the Weissenberg-Rabinowitsch equation, true shear viscosity versus true shear rate is obtained. The device is comprised of a constant-flow generator, a static pressure monitoring device, a high precision submillimeter capillary die, and a high stiffness flow path. The system, which is calibrated using standard Newtonian low-viscosity silicone oil, can be easily operated and maintained. Results for measurement of the shear-rate-dependent viscosity of carbon-black pigmented water-based inkjet inks at shear rates up to 2x10{sup 5} s{sup -1} are discussed. The Cross model was found to closely fit the experimental data. Inkjet ink samples with similar low-shear-rate viscosities exhibited significantly different shear viscosities at high shear rates depending on particle loading.

  7. High Graduate Unemployment Rate and Taiwanese Undergraduate Education

    Science.gov (United States)

    Wu, Chih-Chun

    2011-01-01

    An expansion in higher education in combination with the recent global economic recession has resulted in a high college graduate unemployment rate in Taiwan. This study investigates how the high unemployment rate and financial constraints caused by economic cutbacks have shaped undergraduates' class choices, job needs, and future income…

  8. HIGH-RATE DISINFECTION TECHNIQUES FOR COMBIND SEWER OVERFLOW

    Science.gov (United States)

    This paper presents high-rate disinfection technologies for combined sewer overflow (CSO). The high-rate disinfection technologies of interest are: chlorination/dechlorination, ultraviolet light irradiation (UV), chlorine dioxide (ClO2 ), ozone (O3), peracetic acid (CH3COOOH )...

  9. Comparative Analysis of Continuous Acoustic Emission (AE) Data, Acquired from 12 and 16 Bit Streaming Systems during Rock Deformation Experiments

    Science.gov (United States)

    Flynn, J.; Goodfellow, S. D.; Nasseri, M. H.; Reyes-Montes, J. M.; Young, R.

    2013-12-01

    of the continuous waveform data in both time and frequency domains was performed to analyse changes in AE energy and frequency content throughout the duration of the experiment. This analysis is particularly relevant as the sample approaches failure, as high rates of induced AE events make it difficult to harvest and analyse individual events. Changes in frequency content have been previously observed and associated with microcrack coalescence and the induction of large fractures both in the laboratory and in the monitoring of reservoir stimulations. The comparative analysis shows that the higher resolution in the 16-bit stream provides greater detail in the identification of onset times of sample failure and particularly the changes in amplitude in the different frequency bands.

  10. Efficient Circuit Configuration for Enhancing Resolution of 8-bit flash Analog to Digital Convertor

    Directory of Open Access Journals (Sweden)

    Gururaj Balikatti

    2012-11-01

    Full Text Available The need constantly exists for converters with higher resolution, faster conversion speeds and lower power dissipation. High speed analog to digital converters (ADCs have been based on flash architecture, because all comparators sample the analog input voltage simultaneously, this ADC is thus inherently fast. Unfortunately flash ADC requires 2N - 1 comparators to convert N bit digital code from an analog sample. This makes flash ADCs unsuitable for high resolution applications. The focus of this paper is on efficient circuit configuration to enhance resolution of available 8-bit flash ADC, while maintaining number of comparators only 256 for 12 bit conversion. This technique optimizes the number of comparator requirements. In this approach, an 8-bit flash ADC partitions the analog input range into 256 quantization cells, separated by 255 boundary points. An 8-bit binary code 00000000 to 11111111 is assigned to each cell. The Microcontroller decides within which cell the input sample lies and assigns a 12-bit binary center code 000000000000 to 111111111111 according to the cell value. The exact 12-bit digital code is obtained by successive approximation technique. In this paper the focus will be on all-around efficient circuit for enhancing resolution of 8-bit Flash ADC. It is shown that by adopting this configuration, we can obtain 12-bit digital data just using 256 comparators. Therefore this technique is best suitable when high speed combined with high resolution is required. An experimental prototype of proposed 12-bit ADC was implemented using Philips P89V51RD2BN Microcontroller. Use of Microcontroller has greatly reduced the hardware requirement and cost. An ADC result of 12-bit prototype is presented. The results show that the ADC exhibits a maximum DNL of 0.52LSB and a maximum INL of 0.55LSB.

  11. Compact FPGA-based beamformer using oversampled 1-bit A/D converters.

    Science.gov (United States)

    Tomov, Borislav Gueorguiev; Jensen, Jørgen Arendt

    2005-05-01

    A compact medical ultrasound beamformer architecture that uses oversampled 1-bit analog-to-digital (A/D) converters is presented. Sparse sample processing is used, as the echo signal for the image lines is reconstructed in 512 equidistant focal points along the line through its in-phase and quadrature components. That information is sufficient for presenting a B-mode image and creating a color flow map. The high sampling rate provides the necessary delay resolution for the focusing. The low channel data width (1-bit) makes it possible to construct a compact beamformer logic. The signal reconstruction is done using finite impulse reponse (FIR) filters, applied on selected bit sequences of the delta-sigma modulator output stream. The approach allows for a multichannel beamformer to fit in a single field programmable gate array (FPGA) device. A 32-channel beamformer is estimated to occupy 50% of the available logic resources in a commercially available mid-range FPGA, and to be able to operate at 129 MHz. Simulation of the architecture at 140 MHz provides images with a dynamic range approaching 60 dB for an excitation frequency of 3 MHz.

  12. Geothermal COMPAX drill bit development. Final technical report, July 1, 1976-September 30, 1982

    Energy Technology Data Exchange (ETDEWEB)

    Hibbs, L.E. Jr.; Sogoian, G.C.; Flom, D.G.

    1984-04-01

    The objective was to develop and demonstrate the performance of new drill bit designs utilizing sintered polycrystalline diamond compacts for the cutting edges. The scope included instrumented rock cutting experiments under ambient conditions and at elevated temperature and pressure, diamond compact wear and failure mode analysis, rock removal modeling, bit design and fabrication, full-scale laboratory bit testing, field tests, and performance evaluation. A model was developed relating rock cutting forces to independent variables, using a statistical test design and regression analysis. Experiments on six rock types, covering a range of compressive strengths from 8 x 10/sup 3/ psi to 51 x 10/sup 3/ psi, provided a satisfactory test of the model. Results of the single cutter experiments showed that the cutting and thrust (penetration) forces, and the angle of the resultant force, are markedly affected by rake angle, depth of cut, and speed. No unusual force excursions were detected in interrupted cutting. Wear tests on two types of diamond compacts cutting Jack Fork Sandstone yielded wear rates equivalent at high cutting speeds, where thermal effects are probably operative. At speeds below approx. 400 surface feet per minute (sfm), the coarser sintered diamond product was superior. 28 refs., 235 figs., 55 tabs.

  13. Estimating Hardness from the USDC Tool-Bit Temperature Rise

    Science.gov (United States)

    Bar-Cohen, Yoseph; Sherrit, Stewart

    2008-01-01

    A method of real-time quantification of the hardness of a rock or similar material involves measurement of the temperature, as a function of time, of the tool bit of an ultrasonic/sonic drill corer (USDC) that is being used to drill into the material. The method is based on the idea that, other things being about equal, the rate of rise of temperature and the maximum temperature reached during drilling increase with the hardness of the drilled material. In this method, the temperature is measured by means of a thermocouple embedded in the USDC tool bit near the drilling tip. The hardness of the drilled material can then be determined through correlation of the temperature-rise-versus-time data with time-dependent temperature rises determined in finite-element simulations of, and/or experiments on, drilling at various known rates of advance or known power levels through materials of known hardness. The figure presents an example of empirical temperature-versus-time data for a particular 3.6-mm USDC bit, driven at an average power somewhat below 40 W, drilling through materials of various hardness levels. The temperature readings from within a USDC tool bit can also be used for purposes other than estimating the hardness of the drilled material. For example, they can be especially useful as feedback to control the driving power to prevent thermal damage to the drilled material, the drill bit, or both. In the case of drilling through ice, the temperature readings could be used as a guide to maintaining sufficient drive power to prevent jamming of the drill by preventing refreezing of melted ice in contact with the drill.

  14. Miniature High Stability High Temperature Space Rated Blackbody Radiance Source

    Science.gov (United States)

    Jones, J. A.; Beswick, A. G.

    1987-09-01

    This paper presents the design and test performance of a conical cavity type blackbody radiance source that will meet the requirements of the Halogen Occultation Experiment (HALOE) on the NASA Upper Atmospheric Research Satellite program (UARS). Since a radiance source meeting the requirements of this experiment was unavailable in the commercial market, a development effort was undertaken by the HALOE Project. The blackbody radiance source operates in vacuum at 1300 K + 0.5 K over any 15-minute interval, uses less than 7.5 watts of power, maintains a 49°C outer case temperature, and fits within the 2.5 x 2.5 x 3.0 inch envelope allocated inside the HALOE instrument. Also, the unit operates in air, during ground testing of the HALOE instrument, where it uses 17 watts of power with an outer case temperature of 66°C. The thrust of this design effort was to minimize the heat losses, in order to keep the power usage under 7.5 watts, and to minimize the amount of silica in the materials. Silica in the presence of the platinum heater winding used in this design would cause the platinum to erode, changing the operating temperature set-point. The design required the development of fabrication techniques which would provide very small, close tolerance parts from extremely difficult-to-machine materials. Also, a space rated ceramic core and unique, low thermal conductance, ceramic-to-metal joint was developed, tested and incorporated in this design. The completed flight qualification hardware has undergone performance, environmental and life testing. The design configuration and test results are discussed in detail in this paper.

  15. KEAMANAN CITRA DENGAN WATERMARKING MENGGUNAKAN PENGEMBANGAN ALGORITMA LEAST SIGNIFICANT BIT

    Directory of Open Access Journals (Sweden)

    Kurniawan Kurniawan

    2015-01-01

    Full Text Available Image security is a process to save digital. One method of securing image digital is watermarking using Least Significant Bit algorithm. Main concept of image security using LSB algorithm is to replace bit value of image at specific location so that created pattern. The pattern result of replacing the bit value of image is called by watermark. Giving watermark at image digital using LSB algorithm has simple concept so that the information which is embedded will lost easily when attacked such as noise attack or compression. So need modification like development of LSB algorithm. This is done to decrease distortion of watermark information against those attacks. In this research is divided by 6 process which are color extraction of cover image, busy area search, watermark embed, count the accuracy of watermark embed, watermark extraction, and count the accuracy of watermark extraction. Color extraction of cover image is process to get blue color component from cover image. Watermark information will embed at busy area by search the area which has the greatest number of unsure from cover image. Then watermark image is embedded into cover image so that produce watermarked image using some development of LSB algorithm and search the accuracy by count the Peak Signal to Noise Ratio value. Before the watermarked image is extracted, need to test by giving noise and doing compression into jpg format. The accuracy of extraction result is searched by count the Bit Error Rate value.

  16. Steganography forensics method for detecting least significant bit replacement attack

    Science.gov (United States)

    Wang, Xiaofeng; Wei, Chengcheng; Han, Xiao

    2015-01-01

    We present an image forensics method to detect least significant bit replacement steganography attack. The proposed method provides fine-grained forensics features by using the hierarchical structure that combines pixels correlation and bit-planes correlation. This is achieved via bit-plane decomposition and difference matrices between the least significant bit-plane and each one of the others. Generated forensics features provide the susceptibility (changeability) that will be drastically altered when the cover image is embedded with data to form a stego image. We developed a statistical model based on the forensics features and used least square support vector machine as a classifier to distinguish stego images from cover images. Experimental results show that the proposed method provides the following advantages. (1) The detection rate is noticeably higher than that of some existing methods. (2) It has the expected stability. (3) It is robust for content-preserving manipulations, such as JPEG compression, adding noise, filtering, etc. (4) The proposed method provides satisfactory generalization capability.

  17. A High-Frequency High Frame Rate Duplex Ultrasound Linear Array Imaging System for Small Animal Imaging

    Science.gov (United States)

    Zhang, Lequan; Xu, Xiaochen; Hu, Changhong; Sun, Lei; Yen, Jesse T.; Cannata, Jonathan M.; Shung, K. Kirk

    2010-01-01

    High-frequency (HF) ultrasound imaging has been shown to be useful for non-invasively imaging anatomical structures of the eye and small animals in biological and pharmaceutical research, achieving superior spatial resolution. Cardiovascular research utilizing mice requires not only real-time B-scan imaging, but also ultrasound Doppler to evaluate both anatomy and blood flow of the mouse heart. This paper reports the development of a high frequency ultrasound duplex imaging system capable of both B-mode imaging and Doppler flow measurements, using a 64-element linear array. The system included a HF pulsed-wave Doppler module, a 32-channel HF B-mode imaging module, a PC with a 200 MS/s 14-bit A/D card, and real-time LabView software. A 50dB signal-to-noise ratio (SNR) and a depth of penetration of larger than 12 mm were achieved using a 35 MHz linear array with 50 μm pitch. The two-way beam widths were determined to be 165 μm to 260 μm and the clutter energy to total energy ratio (CTR) were 9.1 dB to 12 dB, when the array was electronically focused at different focal points at depths from 4.8 mm to 9.6 mm. The system is capable of acquiring real-time B-mode images at a rate greater than 400 frames per second (fps) for a 4.8 × 13 mm field of view, using a 30 MHz 64-element linear array with 100 μm pitch. Sample in vivo cardiac high frame rate images and duplex images of mouse hearts are shown to assess its current imaging capability and performance for small animals. PMID:20639149

  18. Are high real interest rates bad for world economic growth?

    OpenAIRE

    1991-01-01

    There is a conventional perception that high real interest rates are bad for economic growth. However, the authors show that close examination of the experience over the last 40 years undermines the existence of such a relationship. For much of the 1950-79 period, expost real interest rates were less than the growth rate of income in the major economies, whereas the 1980s were a period of rapid growth in the world economy that coincided withunprecedentedly high real interest rates. The author...

  19. Bit-string scattering theory

    Energy Technology Data Exchange (ETDEWEB)

    Noyes, H.P.

    1990-01-29

    We construct discrete space-time coordinates separated by the Lorentz-invariant intervals h/mc in space and h/mc{sup 2} in time using discrimination (XOR) between pairs of independently generated bit-strings; we prove that if this space is homogeneous and isotropic, it can have only 1, 2 or 3 spacial dimensions once we have related time to a global ordering operator. On this space we construct exact combinatorial expressions for free particle wave functions taking proper account of the interference between indistinguishable alternative paths created by the construction. Because the end-points of the paths are fixed, they specify completed processes; our wave functions are born collapsed''. A convenient way to represent this model is in terms of complex amplitudes whose squares give the probability for a particular set of observable processes to be completed. For distances much greater than h/mc and times much greater than h/mc{sup 2} our wave functions can be approximated by solutions of the free particle Dirac and Klein-Gordon equations. Using a eight-counter paradigm we relate this construction to scattering experiments involving four distinguishable particles, and indicate how this can be used to calculate electromagnetic and weak scattering processes. We derive a non-perturbative formula relating relativistic bound and resonant state energies to mass ratios and coupling constants, equivalent to our earlier derivation of the Bohr relativistic formula for hydrogen. Using the Fermi-Yang model of the pion as a relativistic bound state containing a nucleon-antinucleon pair, we find that (G{sub {pi}N}{sup 2}){sup 2} = (2m{sub N}/m{sub {pi}}){sup 2} {minus} 1. 21 refs., 1 fig.

  20. High Strain Rate Compressive Tests on Woven Graphite Epoxy Composites

    Science.gov (United States)

    Allazadeh, Mohammad Reza; Wosu, Sylvanus N.

    2011-08-01

    The behavior of composite materials may be different when they are subjected to high strain rate load. Penetrating split Hopkinson pressure bar (P-SHPB) is a method to impose high strain rate on specimen in the laboratory experiments. This research work studied the response of the thin circular shape specimens, made out of woven graphite epoxy composites, to high strain rate impact load. The stress-strain relationships and behavior of the specimens were investigated during the compressive dynamic tests for strain rates as high as 3200 s-1. One dimensional analysis was deployed for analytical calculations since the experiments fulfilled the ratio of diameter to length of bars condition in impact load experiments. The mechanics of dynamic failure was studied and the results showed the factors which govern the failure mode in high strain deformation via absorbed energy by the specimen. In this paper, the relation of particle velocity with perforation depth was discussed for woven graphite epoxy specimens.

  1. Effectiveness of high interest rate policy on exchange rates: A reexamination of the Asian financial crisis

    Directory of Open Access Journals (Sweden)

    Chin Diew Lai

    2006-09-01

    Full Text Available One of the most controversial issues in the aftermath of the Asian financial crisis has been the appropriate response of monetary policy to a sharp decline in the value of some currencies. In this paper, we empirically examine the effects on Asian exchange rates of sharply higher interest rates during the Asian financial crisis. Taking account of the currency contagion effect, our results indicate that sharply higher interest rates helped to support the exchange rates of South Korea, the Philippines, and Thailand. For Malaysia, no significant causal relation is found from the rate of interest to exchange rates, as the authorities in Malaysia did not actively adopt a high interest rate policy to defend the currency.

  2. Thermally induced magnetic switching in bit-patterned media

    Science.gov (United States)

    Pfau, B.; Günther, C. M.; Hauet, T.; Eisebitt, S.; Hellwig, O.

    2017-07-01

    We have studied the thermal variation of the switching field of magnetic islands at room temperature. A model bit-pattern media composed of an assembly of islands with 80 nm width was fabricated by sputter deposition onto a pre-patterned substrate. Using direct magnetic-contrast imaging of the islands under applied field, we extract the switching probabilities of individual islands. Based on an analytical model for the thermally activated switching of the islands, we are able to determine the intrinsic magnetic anisotropy of each island and, consequentially, a distribution of anisotropies for the island ensemble investigated. In the distribution, we identify a separated group of islands with a particularly small anisotropy. We attribute this group to islands containing misaligned grains triggering the magnetic reversal. At room temperature and slow field sweep rates, the observed thermal broadening of the switching-field distribution is small compared to the intrinsic broadening. However, we illustrate that thermal fluctuations play a crucial role at high sweep rates by extrapolating our results to technological relevant regimes.

  3. Tree structure-based bit-to-symbol mapping for multidimensional modulation format

    Science.gov (United States)

    Zhaoxi, Li; Yujuan, Si; Guijun, Hu

    2017-06-01

    Bit-to-symbol mapping is one of the key issues in multidimensional modulation. In an effort to resolve this issue, a tree structure based bit-to-symbol mapping scheme is proposed. By constructing a tree structure of constellation points, any neighboring constellation points become nearest-neighbor constellation points with minimum Euclidean distance, which in turn, changes the bit-to-symbol mapping problem in multidimensional signal modulation from random to orderly. Then, through the orderly distribution of labels, the minimum Hamming distance between the nearest neighboring constellation points is ensured, eventually achieving bit-to-symbol mapping optimization for multidimensional signals. Simulation analysis indicates that, compared with random search mapping, tree mapping can effectively improve the bit error rate performance of multidimensional signal modulation without multiple searching, reducing the computational cost.

  4. A holistic approach to bit preservation

    DEFF Research Database (Denmark)

    Zierau, Eld

    2012-01-01

    Purpose: The purpose of this paper is to point out the importance of taking a holistic approach to bit preservation when setting out to find an optimal bit preservation solution for specific digital materials. In the last decade there has been an increasing awareness that bit preservation, which...... preservation strategies as well as pointing to how such strategies can be evaluated. Research limitations/implications The operational results described here are still missing work to be fully operational. However, the holistic approach is in itself an important result. Furthermore, in spite...

  5. Experimental study of entanglement evolution in the presence of bit-flip and phase-shift noises

    Science.gov (United States)

    Liu, Xia; Cao, Lian-Zhen; Zhao, Jia-Qiang; Yang, Yang; Lu, Huai-Xin

    2017-10-01

    Because of its important role both in fundamental theory and applications in quantum information, evolution of entanglement in a quantum system under decoherence has attracted wide attention in recent years. In this paper, we experimentally generate a high-fidelity maximum entangled two-qubit state and present an experimental study of the decoherence properties of entangled pair of qubits at collective (non-collective) bit-flip and phase-shift noises. The results shown that entanglement decreasing depends on the type of the noises (collective or non-collective and bit-flip or phase-shift) and the number of qubits which are subject to the noise. When two qubits are depolarized passing through non-collective noisy channel, the decay rate is larger than that depicted for the collective noise. When two qubits passing through depolarized noisy channel, the decay rate is larger than that depicted for one qubit.

  6. Klasifikasi Bit-Plane Noise untuk Penyisipan Pesan pada Teknik Steganography BPCS Menggunakan Fuzzy Inference Sistem Mamdani

    Directory of Open Access Journals (Sweden)

    Rahmad Hidayat

    2015-04-01

    Full Text Available Bit-Plane Complexity Segmentation (BPCS is a fairly new steganography technique. The most important process in BPCS is the calculation of complexity value of a bit-plane. The bit-plane complexity is calculated by looking at the amount of bit changes contained in a bit-plane. If a bit-plane has a high complexity, the bi-plane is categorized as a noise bit-plane that does not contain valuable information on the image. Classification of the bit-plane using the set cripst set (noise/not is not fair, where a little difference of the value will significantly change the status of the bit-plane. The purpose of this study is to apply the principles of fuzzy sets to classify the bit-plane into three sets that are informative, partly informative, and the noise region. Classification of the bit-plane into a fuzzy set is expected to classify the bit-plane in a more objective approach and ultimately message capacity of the images can be improved by using the Mamdani fuzzy inference to take decisions which bit-plane will be replaced with a message based on the classification of bit-plane and the size of the message that will be inserted. This research is able to increase the capability of BPCS steganography techniques to insert a message in bit-pane with more precise so that the container image quality would be better. It can be seen that the PSNR value of original image and stego-image is only slightly different.

  7. Putative extremely high rate of proteome innovation in lancelets might be explained by high rate of gene prediction errors.

    Science.gov (United States)

    Bányai, László; Patthy, László

    2016-08-01

    A recent analysis of the genomes of Chinese and Florida lancelets has concluded that the rate of creation of novel protein domain combinations is orders of magnitude greater in lancelets than in other metazoa and it was suggested that continuous activity of transposable elements in lancelets is responsible for this increased rate of protein innovation. Since morphologically Chinese and Florida lancelets are highly conserved, this finding would contradict the observation that high rates of protein innovation are usually associated with major evolutionary innovations. Here we show that the conclusion that the rate of proteome innovation is exceptionally high in lancelets may be unjustified: the differences observed in domain architectures of orthologous proteins of different amphioxus species probably reflect high rates of gene prediction errors rather than true innovation.

  8. Conversion of an 8-bit to a 16-bit Soft-core RISC Processor

    Directory of Open Access Journals (Sweden)

    Ahmad Jamal Salim

    2013-03-01

    Full Text Available The demand for 8-bit processors nowadays is still going strong despite efforts by manufacturers in producing higher end microcontroller solutions to the mass market. Low-end processor offers a simple, low-cost and fast solution especially on I/O applications development in embedded system. However, due to architectural constraint, complex calculation could not be performed efficiently on 8-bit processor. This paper presents the conversion method from an 8-bit to a 16-bit Reduced Instruction Set Computer (RISC processor in a soft-core reconfigurable platform in order to extend its capability in handling larger data sets thus enabling intensive calculations process. While the conversion expands the data bus width to 16-bit, it also maintained the simple architecture design of an 8-bit processor.The expansion also provides more room for improvement to the processor’s performance. The modified architecture is successfully simulated in CPUSim together with its new instruction set architecture (ISA. Xilinx Virtex-6 platform is utilized to execute and verified the architecture. Results show that the modified 16-bit RISC architecture only required 17% more register slice on Field Programmable Gate Array (FPGA implementation which is a slight increase compared to the original 8-bit RISC architecture. A test program containing instruction sets that handle 16-bit data are also simulated and verified. As the 16-bit architecture is described as a soft-core, further modifications could be performed in order to customize the architecture to suit any specific applications.

  9. High Burn Rate Hybrid Fuel for Improved Grain Design Project

    Data.gov (United States)

    National Aeronautics and Space Administration — A novel type of fuel providing high burning rate for hybrid rocket applications is proposed. This fuel maintains a hydrodynamically rough surface to...

  10. High Count Rate Single Photon Counting Detector Array Project

    Data.gov (United States)

    National Aeronautics and Space Administration — An optical communications receiver requires efficient and high-rate photon-counting capability so that the information from every photon, received at the aperture,...

  11. HermesD: A High-Rate Long-Range Wireless Transmission System for Simultaneous Multichannel Neural Recording Applications.

    Science.gov (United States)

    Miranda, Henrique; Gilja, Vikash; Chestek, Cindy A; Shenoy, Krishna V; Meng, Teresa H

    2010-06-01

    HermesD is a high-rate, low-power wireless transmission system to aid research in neural prosthetic systems for motor disabilities and basic motor neuroscience. It is the third generation of our "Hermes systems" aimed at recording and transmitting neural activity from brain-implanted electrode arrays. This system supports the simultaneous transmission of 32 channels of broadband data sampled at 30 ks/s, 12 b/sample, using frequency-shift keying modulation on a carrier frequency adjustable from 3.7 to 4.1 GHz, with a link range extending over 20 m. The channel rate is 24 Mb/s and the bit stream includes synchronization and error detection mechanisms. The power consumption, approximately 142 mW, is low enough to allow the system to operate continuously for 33 h, using two 3.6-V/1200-mAh Li-SOCl2 batteries. The transmitter was designed using off-the-shelf components and is assembled in a stack of three 28 mm ? 28-mm boards that fit in a 38 mm ? 38 mm ? 51-mm aluminum enclosure, a significant size reduction over the initial version of HermesD. A 7-dBi circularly polarized patch antenna is used as the transmitter antenna, while on the receiver side, a 13-dBi circular horn antenna is employed. The advantages of using circularly polarized waves are analyzed and confirmed by indoor measurements. The receiver is a stand-alone device composed of several submodules and is interfaced to a computer for data acquisition and processing. It is based on the superheterodyne architecture and includes automatic frequency control that keeps it optimally tuned to the transmitter frequency. The HermesD communications performance is shown through bit-error rate measurements and eye-diagram plots. The sensitivity of the receiver is -83 dBm for a bit-error probability of 10(-9). Experimental recordings from a rhesus monkey conducting multiple tasks show a signal quality comparable to commercial acquisition systems, both in the low-frequency (local field potentials) and upper-frequency bands

  12. Quantum Communication with a High-Rate Entangled Photon Source

    Science.gov (United States)

    Wilson, Nathaniel C.; Chaffee, Dalton W.; Lekki, John D.; Wilson, Jeffrey D.

    2016-01-01

    A high generation rate photon-pair source using a dual element periodically-poled potassium titanyl phosphate (PP KTP) waveguide is described. The photon-pair source features a high pair generation rate, a compact power-efficient package, and continuous wave (CW) or pulsed operation. Characterization and test results are presented. Details and preliminary results of a laboratory free-space QKD experiment with the B92 protocol are also presented.

  13. High rate resistive plate chamber for LHC detector upgrades

    Energy Technology Data Exchange (ETDEWEB)

    Haddad, Y., E-mail: haddad@llr.in2p3.fr [Laboratoire Leprince-Ringuet (LLR), École Polytechnique, 91120 Palaiseau (France); Laktineh, I.; Grenier, G.; Lumb, N. [IPNL, Villeurbanne 69622 Lyon (France); Cauwenbergh, S. [Ghent University, Ghent (Belgium)

    2013-08-01

    The limitation of the detection rate of standard bakelite resistive plate chambers (RPCs) used as muon detectors in the LHC experiments has prevented the use of such detectors in the high rate regions in both CMS and ATLAS detectors. One alternative to these detectors is RPCs made with low resistivity glass plates (10{sup 10}Ωcm), a beam test at DESY has shown that such detectors can operate at few thousand Hz/cm{sup 2} with high efficiency (>90%)

  14. 基于FPGA的高阶大位宽超声相控阵滤波器设计%High orders and high bit-width FIR design for ultrasonic phased array system based on FPGA

    Institute of Scientific and Technical Information of China (English)

    马骏

    2012-01-01

    超声无损检测中对不同应用采用不同频率特性的超声波换能器。超声相控阵无损检测系统的数字前端需要对不同中心频率的波束成型后的信号进行数字滤波,以便于后续的测量和成像。本文研制了大型超声相控阵无损检测系统中基于FPGA的高阶数、大位宽FIR滤波器,实现了单一滤波器硬件同时支持32位64项非对称系数和127项对称系数.样值位宽为24位,采样率为50MHz,工作频率为400MHz。%The ultrasonic transducers with different frequency characteristics are used for different applications in ultrasonic NDT (Non-Destructive Testing). The heamformed signals must be processed by the FIR filter of ultrasonic phased array digital front-end for next stage measurement and imaging. This paper describes the design and implementation of the FIR on Xilinx Virtex-6 FPGA. The FIR supports 32-bit, 64 taps non-symmetrical coefficient set or 32-hit, 127 taps symmetrical coefficient set, and 24-bit sam- pling data at 50MHz sampling frequency in a single hardware. The working freouencv of the FIR is 400MHz.

  15. Secure Classical Bit Commitment using Fixed Capacity Communication Channels

    OpenAIRE

    Kent, Adrian

    1999-01-01

    If mutually mistrustful parties A and B control two or more appropriately located sites, special relativity can be used to guarantee that a pair of messages exchanged by A and B are independent. In earlier work, we used this fact to define a relativistic bit commitment protocol, RBC1, in which security is maintained by exchanging a sequence of messages whose transmission rate increases exponentially in time. We define here a new relativistic protocol, RBC2, which requires only a constant tran...

  16. Parity Bit Replenishment for JPEG 2000-Based Video Streaming

    Directory of Open Access Journals (Sweden)

    François-Olivier Devaux

    2009-01-01

    Full Text Available This paper envisions coding with side information to design a highly scalable video codec. To achieve fine-grained scalability in terms of resolution, quality, and spatial access as well as temporal access to individual frames, the JPEG 2000 coding algorithm has been considered as the reference algorithm to encode INTRA information, and coding with side information has been envisioned to refresh the blocks that change between two consecutive images of a video sequence. One advantage of coding with side information compared to conventional closed-loop hybrid video coding schemes lies in the fact that parity bits are designed to correct stochastic errors and not to encode deterministic prediction errors. This enables the codec to support some desynchronization between the encoder and the decoder, which is particularly helpful to adapt on the fly pre-encoded content to fluctuating network resources and/or user preferences in terms of regions of interest. Regarding the coding scheme itself, to preserve both quality scalability and compliance to the JPEG 2000 wavelet representation, a particular attention has been devoted to the definition of a practical coding framework able to exploit not only the temporal but also spatial correlation among wavelet subbands coefficients, while computing the parity bits on subsets of wavelet bit-planes. Simulations have shown that compared to pure INTRA-based conditional replenishment solutions, the addition of the parity bits option decreases the transmission cost in terms of bandwidth, while preserving access flexibility.

  17. Effect of bit wear on hammer drill handle vibration and productivity.

    Science.gov (United States)

    Antonucci, Andrea; Barr, Alan; Martin, Bernard; Rempel, David

    2017-08-01

    The use of large electric hammer drills exposes construction workers to high levels of hand vibration that may lead to hand-arm vibration syndrome and other musculoskeletal disorders. The aim of this laboratory study was to investigate the effect of bit wear on drill handle vibration and drilling productivity (e.g., drilling time per hole). A laboratory test bench system was used with an 8.3 kg electric hammer drill and 1.9 cm concrete bit (a typical drill and bit used in commercial construction). The system automatically advanced the active drill into aged concrete block under feed force control to a depth of 7.6 cm while handle vibration was measured according to ISO standards (ISO 5349 and 28927). Bits were worn to 4 levels by consecutive hole drilling to 4 cumulative drilling depths: 0, 1,900, 5,700, and 7,600 cm. Z-axis handle vibration increased significantly (pvibration did not increase further with bits worn more than 1900 cm of cumulative drilling depth. Neither x- nor y-axis handle vibration was effected by bit wear. The time to drill a hole increased by 58% for the bit with 5,700 cm of cumulative drilling depth compared to a new bit. Bit wear led to a small but significant increase in both ISO weighted and unweighted z-axis handle vibration. Perhaps more important, bit wear had a large effect on productivity. The effect on productivity will influence a worker's allowable daily drilling time if exposure to drill handle vibration is near the ACGIH Threshold Limit Value. ([1]) Construction contractors should implement a bit replacement program based on these findings.

  18. Design of High-Performance 32 bit Adder with Semi-Dynamic Circuit%基于半动态电路的32位高性能加法器设计

    Institute of Scientific and Technical Information of China (English)

    刘志哲; 仲顺安; 袁家芬

    2011-01-01

    描述了一种采用半动态电路的32位高性能加法器的设计.设计中改进了现有稀疏树结构中的输出进位逻辑,在此基础上,设计了一种容偏斜多米诺和静态电路相结合的半动态电路,以及相应的多个控制时钟的时序策略.根据几种不同的加法器负载驱动情况,分别设计出不同的电路尺寸.采用SMIC 1.8 V 0.18 μm CMOS工艺,在不同条件下的仿真结果表明,加法器电路取得了良好的性能.%This paper presents a programme of designing 32 bit high-performance adder with semidynamic circuit. With modified output carry logic in sparse-tree structure, the semi-dynamic adder circuit, which includes skew-tolerant dynamic domino-circuit and static circuit, and its multiple clocks timing scheme were designed. The different transistor's sizes of adder were designed to fit the different loads and drive conditions of the adder. In SMIC 1.8 V 0. 18 μm technology, the simulation results under different conditions show that the designed adder has a high performance.

  19. High strain rate loading of polymeric foams and solid plastics

    Science.gov (United States)

    Dick, Richard D.; Chang, Peter C.; Fourney, William L.

    2000-04-01

    The split-Hopkinson pressure bar (SHPB) provided a technique to determine the high strain rate response for low density foams and solid ABS and polypropylene plastics. These materials are used in the interior safety panels of automobiles and crash test dummies. Because the foams have a very low impedance, polycarbonate bars were used to acquire the strain rate data in the 100 to 1600 l/s range. An aluminum SPHB setup was used to obtain the solid plastics data which covered strain rates of 1000 to 4000 l/s. The curves for peak strain rate versus peak stress for the foams over the test range studied indicates only a slight strain rate dependence. Peak strain rate versus peak stress curves for polypropylene shows a strain rate dependence up to about 1500 l/s. At that rate the solid poly propylene indicates no strain rate dependence. The ABS plastics are strain rate dependent up to 3500 l/s and then are independent at larger strain rates.

  20. HIGH HEATING RATES AFFECTS GREATLY THE INACTIVATION RATE OF ESCHERICHIA COLI

    Directory of Open Access Journals (Sweden)

    Juan Pablo Huertas

    2016-08-01

    Full Text Available Heat resistance of microorganisms can be affected by different influencing factors. Although the effect of heating rates has been scarcely explored by the scientific community, recent researches have unraveled its important effect on the thermal resistance of different species of vegetative bacteria. Typically heating rates described in the literature ranged from 1 to 20ºC/min but the impact of much higher heating rates is unclear. The aim of this research was to explore the effect of different heating rates, such as those currently achieved in the heat exchangers used in the food industry, on the heat resistance of Escherichia coli. A pilot plant tubular heat exchanger and a thermoresistometer Mastia were used for this purpose. Results showed that fast heating rates had a deep impact on the thermal resistance of E. coli. Heating rates between 20 and 50ºC/min were achieved in the heat exchanger, which were much slower than those around 20ºC/s achieved in the thermoresistometer. In all cases, these high heating rates led to higher inactivation than expected: in the heat exchanger, for all the experiments performed, when the observed inactivation had reached about seven log cycles, the predictions estimates about 1 log cycle of inactivation; in the thermoresistometer these differences between observed and predicted values were even more than ten times higher, from 4.07 log cycles observed to 0.34 predicted at a flow rate of 70 mL/min and a maximum heating rate of 14.7ºC/s. A quantification of the impact of the heating rates on the level of inactivation achieved was established. These results point out the important effect that the heating rate has on the thermal resistance of E. coli, with high heating rates resulting in an additional sensitization to heat and therefore an effective food safety strategy in terms of food processing.

  1. High Heating Rates Affect Greatly the Inactivation Rate of Escherichia coli

    Science.gov (United States)

    Huertas, Juan-Pablo; Aznar, Arantxa; Esnoz, Arturo; Fernández, Pablo S.; Iguaz, Asunción; Periago, Paula M.; Palop, Alfredo

    2016-01-01

    Heat resistance of microorganisms can be affected by different influencing factors. Although, the effect of heating rates has been scarcely explored by the scientific community, recent researches have unraveled its important effect on the thermal resistance of different species of vegetative bacteria. Typically heating rates described in the literature ranged from 1 to 20°C/min but the impact of much higher heating rates is unclear. The aim of this research was to explore the effect of different heating rates, such as those currently achieved in the heat exchangers used in the food industry, on the heat resistance of Escherichia coli. A pilot plant tubular heat exchanger and a thermoresistometer Mastia were used for this purpose. Results showed that fast heating rates had a deep impact on the thermal resistance of E. coli. Heating rates between 20 and 50°C/min were achieved in the heat exchanger, which were much slower than those around 20°C/s achieved in the thermoresistometer. In all cases, these high heating rates led to higher inactivation than expected: in the heat exchanger, for all the experiments performed, when the observed inactivation had reached about seven log cycles, the predictions estimated about 1 log cycle of inactivation; in the thermoresistometer these differences between observed and predicted values were even more than 10 times higher, from 4.07 log cycles observed to 0.34 predicted at a flow rate of 70 mL/min and a maximum heating rate of 14.7°C/s. A quantification of the impact of the heating rates on the level of inactivation achieved was established. These results point out the important effect that the heating rate has on the thermal resistance of E. coli, with high heating rates resulting in an additional sensitization to heat and therefore an effective food safety strategy in terms of food processing. PMID:27563300

  2. The Braid-Based Bit Commitment Protocol

    Institute of Scientific and Technical Information of China (English)

    WANG Li-cheng; CAO Zhen-fu; CAO Feng; QIAN Hai-feng

    2006-01-01

    With recent advances of quantum computation, new threats have closed in upon to the classical public key cryptosystems. In order to build more secure bit commitment schemes, this paper gave a survey of the new coming braid-based cryptography and then brought forward the first braid-based bit commitment protocol. The security proof manifests that the proposed protocol is computationally binding and information-theoretically hiding.Furthermore, the proposed protocol is also invulnerable to currently known quantum attacks.

  3. Radio Interface for High Data Rate Wireless Sensor Networks

    CERN Document Server

    Henaut, Julien; Dragomirescu, Daniela; Plana, Robert

    2010-01-01

    This paper gives an overview of radio interfaces devoted for high data rate Wireless Sensor Networks. Four aerospace applications of WSN are presented to underline the importance of achieving high data rate. Then, two modulation schemes by which High Data Rate can be achieved are compared : Multi carrier approaches, represented by the popular Orthogonal Frequency Division Multiplexing (OFDM) and Single carrier methods, represented by Single Carrier Frequency division Equalization and its application for multiple access Single Carrier Frequency division multiple Access (SC-FDMA). SC-FDMA, with a very low Peak Average Power Ratio (PAPR), is as strong alternative to the OFDM scheme for highly power constraint application. The Chosen radio interface will be, finally, tested by a model based design approach based on Simulink and FPGA realization. SC-FDMA, with a very low Peak Average Power Ratio (PAPR), is as strong alternative to the OFDM scheme for highly power constraint application. The Chosen radio interface ...

  4. Neural network implementation using bit streams.

    Science.gov (United States)

    Patel, Nitish D; Nguang, Sing Kiong; Coghill, George G

    2007-09-01

    A new method for the parallel hardware implementation of artificial neural networks (ANNs) using digital techniques is presented. Signals are represented using uniformly weighted single-bit streams. Techniques for generating bit streams from analog or multibit inputs are also presented. This single-bit representation offers significant advantages over multibit representations since they mitigate the fan-in and fan-out issues which are typical to distributed systems. To process these bit streams using ANNs concepts, functional elements which perform summing, scaling, and squashing have been implemented. These elements are modular and have been designed such that they can be easily interconnected. Two new architectures which act as monotonically increasing differentiable nonlinear squashing functions have also been presented. Using these functional elements, a multilayer perceptron (MLP) can be easily constructed. Two examples successfully demonstrate the use of bit streams in the implementation of ANNs. Since every functional element is individually instantiated, the implementation is genuinely parallel. The results clearly show that this bit-stream technique is viable for the hardware implementation of a variety of distributed systems and for ANNs in particular.

  5. Stretching Behavior of Red Blood Cells at High Strain Rates

    Science.gov (United States)

    Mancuso, Jordan; Ristenpart, William

    2016-11-01

    Most work on the mechanical behavior of red blood cells (RBCs) has focused on simple shear flows. Relatively little work has examined RBC deformations in the physiologically important extensional flow that occurs at the entrance to a constriction. In particular, previous work suggests that RBCs rapidly stretch out and then retract upon entering the constriction, but to date no model predicts this behavior for the extremely high strain rates typically experienced there. In this work, we use high speed video to perform systematic measurements of the dynamic stretching behavior of RBCs as they enter a microfluidic constriction. We demonstrate that a simple viscoelastic model captures the observed stretching dynamics, up to strain rates as high as 1000 s-1. The results indicate that the effective elastic modulus of the RBC membrane at these strain rates is an order of magnitude larger than moduli measured by micropipette aspiration or other low strain rate techniques.

  6. Solidification at the High and Low Rate Extreme

    Energy Technology Data Exchange (ETDEWEB)

    Meco, Halim [Iowa State Univ., Ames, IA (United States)

    2004-12-19

    The microstructures formed upon solidification are strongly influenced by the imposed growth rates on an alloy system. Depending on the characteristics of the solidification process, a wide range of growth rates is accessible. The prevailing solidification mechanisms, and thus the final microstructure of the alloy, are governed by these imposed growth rates. At the high rate extreme, for instance, one can have access to novel microstructures that are unattainable at low growth rates. While the low growth rates can be utilized for the study of the intrinsic growth behavior of a certain phase growing from the melt. Although the length scales associated with certain processes, such as capillarity, and the diffusion of heat and solute, are different at low and high rate extremes, the phenomena that govern the selection of a certain microstructural length scale or a growth mode are the same. Consequently, one can analyze the solidification phenomena at both high and low rates by using the same governing principles. In this study, we examined the microstructural control at both low and high extremes. For the high rate extreme, the formation of crystalline products and factors that control the microstructure during rapid solidification by free-jet melt spinning are examined in Fe-Si-B system. Particular attention was given to the behavior of the melt pool at different quench-wheel speeds. Since the solidification process takes place within the melt-pool that forms on the rotating quench-wheel, we examined the influence of melt-pool dynamics on nucleation and growth of crystalline solidification products and glass formation. High-speed imaging of the melt-pool, analysis of ribbon microstructure, and measurement of ribbon geometry and surface character all indicate upper and lower limits for melt-spinning rates for which nucleation can be avoided, and fully amorphous ribbons can be achieved. Comparison of the relevant time scales reveals that surface-controlled melt

  7. HEPS-BPIX, a single photon counting pixel detector with a high frame rate for the HEPS project

    Science.gov (United States)

    Wei, Wei; Zhang, Jie; Ning, Zhe; Lu, Yunpeng; Fan, Lei; Li, Huaishen; Jiang, Xiaoshan; Lan, Allan K.; Ouyang, Qun; Wang, Zheng; Zhu, Kejun; Chen, Yuanbo; Liu, Peng

    2016-11-01

    China's next generation light source, named the High Energy Photon Source (HEPS), is currently under construction. HEPS-BPIX (HEPS-Beijing PIXel) is a dedicated pixel readout chip that operates in single photon counting mode for X-ray applications in HEPS. Designed using CMOS 0.13 μm technology, the chip contains a matrix of 104×72 pixels. Each pixel measures 150 μm×150 μm and has a counting depth of 20 bits. A bump-bonded prototyping detector module with a 300-μm thick silicon sensor was tested in the beamline of Beijing Synchrotron Radiation Facility. A fast stream of X-ray images was demonstrated, and a frame rate of 1.2 kHz was proven, with a negligible dead time. The test results showed an equivalent noise charge of 115 e- rms after bump bonding and a threshold dispersion of 55 e- rms after calibration.

  8. High deposition rate nanocrystalline silicon with enhanced homogeneity

    NARCIS (Netherlands)

    Verkerk, A.; Rath, J.K.; Schropp, R.E.I.

    2010-01-01

    High rate growth of hydrogenated nanocrystalline silicon (nc-Si:H) brings additional challenges for the homogeneity in the growth direction, since the start-up effects affect a larger portion of the film, and the very high degree of depletion increases the influence of back diffusion from the inacti

  9. Multi-bit upset aware hybrid error-correction for cache in embedded processors

    Science.gov (United States)

    Jiaqi, Dong; Keni, Qiu; Weigong, Zhang; Jing, Wang; Zhenzhen, Wang; Lihua, Ding

    2015-11-01

    For the processor working in the radiation environment in space, it tends to suffer from the single event effect on circuits and system failures, due to cosmic rays and high energy particle radiation. Therefore, the reliability of the processor has become an increasingly serious issue. The BCH-based error correction code can correct multi-bit errors, but it introduces large latency overhead. This paper proposes a hybrid error correction approach that combines BCH and EDAC to correct both multi-bit and single-bit errors for caches with low cost. The proposed technique can correct up to four-bit error, and correct single-bit error in one cycle. Evaluation results show that, the proposed hybrid error-correction scheme can improve the performance of cache accesses up to 20% compared to the pure BCH scheme.

  10. High-rate squeezing process of bulk metallic glasses

    Science.gov (United States)

    Fan, Jitang

    2017-03-01

    High-rate squeezing process of bulk metallic glasses from a cylinder into an intact sheet achieved by impact loading is investigated. Such a large deformation is caused by plastic flow, accompanied with geometrical confinement, shear banding/slipping, thermo softening, melting and joining. Temperature rise during the high-rate squeezing process makes a main effect. The inherent mechanisms are illustrated. Like high-pressure torsion (HPT), equal channel angular pressing (ECAP) and surface mechanical attrition treatments (SMAT) for refining grain of metals, High-Rate Squeezing (HRS), as a multiple-functions technique, not only creates a new road of processing metallic glasses and other metallic alloys for developing advanced materials, but also directs a novel technology of processing, grain refining, coating, welding and so on for treating materials.

  11. Development of Asymmetric Hydrogenation Catalysts via High Throughput Experimentation Développement de catalyseurs d’hydrogénation asymétrique par criblage haut débit

    Directory of Open Access Journals (Sweden)

    de Vries J. G.

    2013-02-01

    Full Text Available The dynamics of drugs discovery imposes severe time constraints on the development chemist in charge of implementing the large scale production of a new Active Pharmaceutical Ingredient (API. This results in the use of well-established and robust transformations at the expense of the cost-efficiency and the sustainability of the process. In order to cope with the short development time and allow the implementation of new more efficient production technologies such as asymmetric hydrogenation, we have turned towards the use of high throughput experimentation for the discovery of new catalysts. The protocol for the preparation of a library of chiral ligands and its application to real-life pharmaceutical molecules is described in this article. La découverte de nouvelles molécules pharmaceutiques a sa propre dynamique qui impose des contraintes temporelles très strictes au chimiste en charge de développer la production du principe actif à large échelle. En conséquence, ce dernier va se tourner vers l’utilisation de technologies éprouvées et robustes quitte à rendre le procédé plus coûteux ou plus polluant. Afin de pouvoir faire face à des temps de développement très courts et d’introduire en production des technologies modernes et non polluantes comme l’hydrogénation asymétrique, nous avons développé une plateforme de criblage haut débit pour la découverte de nouveaux catalyseurs. Dans cet article, nous décrivons une des facettes de cette plateforme qui est la synthèse de librairies de ligands chiraux et leur application au cas réel d’une molécule pharmaceutique.

  12. 面向高速应用的10位2GHz数模转换器%A 10bit 2GHz CMOS D/A Converter for High-Speed System Applications

    Institute of Scientific and Technical Information of China (English)

    袁凌; 倪卫宁; 石寅

    2007-01-01

    提出了一个刷新率达2GHz的10位电流驱动型数模转换器.在综合了精度与芯片面积等因素之后,该数模转换器使用6+4结构.采用电流型逻辑以提高转换器的速度,并采用Q2 random walk方法设计了一个双中心对称的电流矩阵,确保数模转换器的线性度.该数模转换器核心版图面积为2.2mm×2.2mm,在3.3V单电压供电的情况下,该芯片功耗为790mW.%This paper presents a 2GS/s 10bit CMOS digital-to-analog converter (DAC) that consists of two unit current-cell matrixes for 6MSBs and 4LSBs,respectively,trading off between the precision and size of the chip.Current mode logic (CML) is used to ensure high speed,and a double centro-symmetric current matrix is designed by the Q2 random walk strategy in order to ensure the linearity of the DAC. The DAC occupies 2.2mm × 2. 2mm of die area and consumes 790mW with a single 3. 3V power supply.

  13. High power, high efficiency millimeter wavelength traveling wave tubes for high rate communications from deep space

    Science.gov (United States)

    Dayton, James A., Jr.

    1991-01-01

    The high-power transmitters needed for high data rate communications from deep space will require a new class of compact, high efficiency traveling wave tubes (TWT's). Many of the recent TWT developments in the microwave frequency range are generically applicable to mm wave devices, in particular much of the technology of computer aided design, cathodes, and multistage depressed collectors. However, because TWT dimensions scale approximately with wavelength, mm wave devices will be physically much smaller with inherently more stringent fabrication tolerances and sensitivity to thermal dissipation.

  14. Evolution of high tooth replacement rates in sauropod dinosaurs.

    Directory of Open Access Journals (Sweden)

    Michael D D'Emic

    Full Text Available BACKGROUND: Tooth replacement rate can be calculated in extinct animals by counting incremental lines of deposition in tooth dentin. Calculating this rate in several taxa allows for the study of the evolution of tooth replacement rate. Sauropod dinosaurs, the largest terrestrial animals that ever evolved, exhibited a diversity of tooth sizes and shapes, but little is known about their tooth replacement rates. METHODOLOGY/PRINCIPAL FINDINGS: We present tooth replacement rate, formation time, crown volume, total dentition volume, and enamel thickness for two coexisting but distantly related and morphologically disparate sauropod dinosaurs Camarasaurus and Diplodocus. Individual tooth formation time was determined by counting daily incremental lines in dentin. Tooth replacement rate is calculated as the difference between the number of days recorded in successive replacement teeth. Each tooth family in Camarasaurus has a maximum of three replacement teeth, whereas each Diplodocus tooth family has up to five. Tooth formation times are about 1.7 times longer in Camarasaurus than in Diplodocus (315 vs. 185 days. Average tooth replacement rate in Camarasaurus is about one tooth every 62 days versus about one tooth every 35 days in Diplodocus. Despite slower tooth replacement rates in Camarasaurus, the volumetric rate of Camarasaurus tooth replacement is 10 times faster than in Diplodocus because of its substantially greater tooth volumes. A novel method to estimate replacement rate was developed and applied to several other sauropodomorphs that we were not able to thin section. CONCLUSIONS/SIGNIFICANCE: Differences in tooth replacement rate among sauropodomorphs likely reflect disparate feeding strategies and/or food choices, which would have facilitated the coexistence of these gigantic herbivores in one ecosystem. Early neosauropods are characterized by high tooth replacement rates (despite their large tooth size, and derived titanosaurs and

  15. Bits of Internet traffic control

    OpenAIRE

    Vojnovic, Milan; Le Boudec, Jean Yves

    2005-01-01

    In this work, we consider four problems in the context of Internet traffic control. The first problem is to understand when and why a sender that implements an equation-based rate control would be TCP-friendly, or not—a sender is said to be TCP-friendly if, under the same operating conditions, its long-term average send rate does not exceed that of a TCP sender. It is an established axiom that some senders in the Internet would need to be TCP-friendly. An equation-based rate control sender pl...

  16. Bits of Internet Traffic Control

    OpenAIRE

    Vojnovic, Milan

    2003-01-01

    In this work, we consider four problems in the context of Internet traffic control. The first problem is to understand when and why a sender that implements an equation-based rate control would be TCP-friendly, or not—a sender is said to be TCP-friendly if, under the same operating conditions, its long-term average send rate does not exceed that of a TCP sender. It is an established axiom that some senders in the Internet would need to be TCP-friendly. An equation-based rate control sender pl...

  17. High Frame Rate Synthetic Aperture 3D Vector Flow Imaging

    DEFF Research Database (Denmark)

    Villagómez Hoyos, Carlos Armando; Holbek, Simon; Stuart, Matthias Bo

    2016-01-01

    3-D blood flow quantification with high spatial and temporal resolution would strongly benefit clinical research on cardiovascular pathologies. Ultrasonic velocity techniques are known for their ability to measure blood flow with high precision at high spatial and temporal resolution. However......, current volumetric ultrasonic flow methods are limited to one velocity component or restricted to a reduced field of view (FOV), e.g. fixed imaging planes, in exchange for higher temporal resolutions. To solve these problems, a previously proposed accurate 2-D high frame rate vector flow imaging (VFI......) technique is extended to estimate the 3-D velocity components inside a volume at high temporal resolutions (

  18. High Strain Rate Behavior of Polymer Matrix Composites Analyzed

    Science.gov (United States)

    Goldberg, Robert K.; Roberts, Gary D.

    2001-01-01

    Procedures for modeling the high-speed impact of composite materials are needed for designing reliable composite engine cases that are lighter than the metal cases in current use. The types of polymer matrix composites that are likely to be used in such an application have a deformation response that is nonlinear and that varies with strain rate. To characterize and validate material models that could be used in the design of impactresistant engine cases, researchers must obtain material data over a wide variety of strain rates. An experimental program has been carried out through a university grant with the Ohio State University to obtain deformation data for a representative polymer matrix composite for strain rates ranging from quasi-static to high rates of several hundred per second. This information has been used to characterize and validate a constitutive model that was developed at the NASA Glenn Research Center.

  19. Solutions for ultra-high speed optical wavelength conversion and clock recovery

    DEFF Research Database (Denmark)

    Oxenløwe, Leif Katsuo; Galili, Michael; Mulvad, Hans Christian Hansen

    2006-01-01

    This paper reports on our recent advances in ultra-fast optical communications relying on ultra-short pulses densely stacked in ultra-high bit rate serial data signals at a single wavelength. The paper describes details in solutions for the network functionalities of wavelength conversion and clock...... recovery at bit rates up to 320 Gb/s...

  20. Telemetry System Parameters and Bit Error Performance of NRZ and DM PCM/FM

    Science.gov (United States)

    1976-03-29

    MODEL 400 4·POLE, LINEAR L ________ J PHASE FILTER ANDOM OM PSEUDO·R 0 PSEUDO·RA R NDOM :’olRZ EMR 721 TELEMETRY RECOVERED PCM SEQUENCE BIT...with variable bit rate. The NRZ and DM signals were pseudo-random sequences of 2,047 bits. The pre- modulation filter was a four-pole, linear phase ... filter with adjustable bandwidth. RF transmitter devia- tion and RF attenuation were adjustable on the FM signal generator which was operated at

  1. Inadvertently programmed bits in Samsung 128 Mbit flash devices: a flaky investigation

    Science.gov (United States)

    Swift, G.

    2002-01-01

    JPL's X2000 avionics design pioneers new territory by specifying a non-volatile memory (NVM) board based on flash memories. The Samsung 128Mb device chosen was found to demonstrate bit errors (mostly program disturbs) and block-erase failures that increase with cycling. Low temperature, certain pseudo- random patterns, and, probably, higher bias increase the observable bit errors. An experiment was conducted to determine the wearout dependence of the bit errors to 100k cycles at cold temperature using flight-lot devices (some pre-irradiated). The results show an exponential growth rate, a wide part-to-part variation, and some annealing behavior.

  2. Inadvertently programmed bits in Samsung 128 Mbit flash devices: a flaky investigation

    Science.gov (United States)

    Swift, G.

    2002-01-01

    JPL's X2000 avionics design pioneers new territory by specifying a non-volatile memory (NVM) board based on flash memories. The Samsung 128Mb device chosen was found to demonstrate bit errors (mostly program disturbs) and block-erase failures that increase with cycling. Low temperature, certain pseudo- random patterns, and, probably, higher bias increase the observable bit errors. An experiment was conducted to determine the wearout dependence of the bit errors to 100k cycles at cold temperature using flight-lot devices (some pre-irradiated). The results show an exponential growth rate, a wide part-to-part variation, and some annealing behavior.

  3. Study of High Strain Rate Response of Composites

    Science.gov (United States)

    Gilat, Amos

    2003-01-01

    The objective of the research was to continue the experimental study of the effect of strain rate on mechanical response (deformation and failure) of epoxy resins and carbon fibers/epoxy matrix composites, and to initiate a study of the effects of temperature by developing an elevated temperature test. The experimental data provide the information needed for NASA scientists for the development of a nonlinear, rate dependent deformation and strength models for composites that can subsequently be used in design. This year effort was directed into testing the epoxy resin. Three types of epoxy resins were tested in tension and shear at various strain rates that ranges from 5 x 10(exp -5), to 1000 per second. Pilot shear experiments were done at high strain rate and an elevated temperature of 80 C. The results show that all, the strain rate, the mode of loading, and temperature significantly affect the response of epoxy.

  4. STIR: Tailored Interfaces for High Strength Composites Across Strain Rates

    Science.gov (United States)

    2013-09-02

    was requested during our kickoff meeting at ARL APG. High performance fabrics including Kevlar, Twaron, Zylon , and Dyneema are used in developing...Kevlar, and Zylon for various pullout rates. Force– displacement data was recorded, and both warp and fill yarns were pulled from the fabric. Their...results presented that the effect of pullout rate is negligible for Kevlar, whereas the effect is bigger on Spectra, and significant for Zylon

  5. High rate tests of the LHCb RICH Upgrade system

    CERN Multimedia

    Blago, Michele Piero

    2016-01-01

    One of the biggest challenges for the upgrade of the LHCb RICH detectors from 2020 is to readout the photon detectors at the full 40 MHz rate of the LHC proton-proton collisions. A test facility has been setup at CERN with the purpose to investigate the behaviour of the Multi Anode PMTs, which have been proposed for the upgrade, and their readout electronics at high trigger rates. The MaPMTs are illuminated with a monochromatic laser that can be triggered independently of the readout electronics. A first series of tests, including threshold scans, is performed at low trigger rates (20 kHz) for both the readout and the laser with the purpose to characterise the behaviour of the system under test. Then the trigger rate is increased in two separate steps. First the MaPMTs are exposed to high illumination by triggering the pulsed laser at a high (20 MHz) repetition rate while the DAQ is readout at the same low rate as before. In this way the performance of the MaPMTs and the attached electronics can be evaluated ...

  6. Nanoengineering Titania for High Rate Lithium Storage: A Review

    Institute of Scientific and Technical Information of China (English)

    Chunhai Jiang; Jinsong Zhang

    2013-01-01

    Nanostructured titania have been intensively investigated as anode materials of Li-ion batteries for their excellent high rate performance.The size effects of TiO2 polymorphs (mainly rutile,anatase and TiO2-B) on their electrochemical performance and the latest efforts in nanoengineering titania anodes through enhancing their ionic or electronic transportation or both are reviewed in this work.We suppose that micron-or submicronsized porous structures assembled by TiO2 nanoparticles,nanowires/nanotubes or nanosheets with a high percentage of exposing high reactive facets together with a conductive percolating network are ideal anodes not only for high rate lithium storage but also for high packing densities of the active materials.

  7. Semi-solid electrodes having high rate capability

    Energy Technology Data Exchange (ETDEWEB)

    Chiang, Yet-Ming; Duduta, Mihai; Holman, Richard; Limthongkul, Pimpa; Tan, Taison

    2016-07-05

    Embodiments described herein relate generally to electrochemical cells having high rate capability, and more particularly to devices, systems and methods of producing high capacity and high rate capability batteries having relatively thick semi-solid electrodes. In some embodiments, an electrochemical cell includes an anode, a semi-solid cathode that includes a suspension of an active material and a conductive material in a liquid electrolyte, and an ion permeable membrane disposed between the anode and the cathode. The semi-solid cathode has a thickness in the range of about 250 .mu.m-2,500 .mu.m, and the electrochemical cell has an area specific capacity of at least 5 mAh/cm.sup.2 at a C-rate of C/2.

  8. Semi-solid electrodes having high rate capability

    Energy Technology Data Exchange (ETDEWEB)

    Chiang, Yet-Ming; Duduta, Mihai; Holman, Richard; Limthongkul, Pimpa; Tan, Taison

    2015-11-10

    Embodiments described herein relate generally to electrochemical cells having high rate capability, and more particularly to devices, systems and methods of producing high capacity and high rate capability batteries having relatively thick semi-solid electrodes. In some embodiments, an electrochemical cell includes an anode, a semi-solid cathode that includes a suspension of an active material and a conductive material in a liquid electrolyte, and an ion permeable membrane disposed between the anode and the cathode. The semi-solid cathode has a thickness in the range of about 250 .mu.m-2,500 .mu.m, and the electrochemical cell has an area specific capacity of at least 5 mAh/cm.sup.2 at a C-rate of C/2.

  9. High strain rate compression testing of glass fibre reinforced polypropylene

    Directory of Open Access Journals (Sweden)

    Cloete T.J.

    2012-08-01

    Full Text Available This paper details an investigation of the high strain rate compression testing of GFPP with the Split Hopkinson Pressure Bar (SHPB in the through-thickness and in-plane directions. GFPP posed challenges to SHPB testing as it fails at relatively high stresses, while having relatively low moduli and hence mechanical impedance. The modifications to specimen geometry and incident pulse shaping in order to gather valid test results, where specimen equilibrium was achieved for SHPB tests on GFPP are presented. In addition to conventional SHPB tests to failure, SHPB experiments were designed to achieve specimen equilibration at small strains, which permitted the capture of high strain rate elastic modulus data. The strain rate dependency of GFPP’s failure strengths in the in-plane and through-thickness direction is modelled using a logarithmic law.

  10. High-Strain Rate Mechanical Response of Cured Epoxy Networks

    Science.gov (United States)

    Sirk, Timothy; Khare, Ketan; Karim, Mir; Lenhart, Joseph; Khare, Rajesh; Andzelm, Jan

    2013-03-01

    Chemically cross-linked polymer networks are increasingly common in high performance composites, adhesives and other applications involving high-impact loading conditions or ballistic collisions. The mechanical behavior of epoxy and other polymer networks exhibit a strong dependence on strain rate near the glass transition temperature (Tg); however, the elastic modulus at strain rates greater than 105 1/s is difficult to capture with experimental techniques. We present computational results of Di-Glycidyl Ether of Bisphenol A (DGEBA) and Jeffamine diamines (D230) from molecular dynamics simulation, which is intrinsically well-suited to model material deformation at high strain rates. Our results show that the experimental Tg can be reproduced from molecular dynamics, and the Williams-Landel-Ferry equation is useful in rationalizing the shift of Tg due to fast annealing and high strain rates. Temperature sweeps of elastic modulus show the glass-rubber transition to occur over a significantly wider temperature range compared with experimental measurements at low strain rates.

  11. High removal rate laser-based coating removal system

    Science.gov (United States)

    Matthews, Dennis L.; Celliers, Peter M.; Hackel, Lloyd; Da Silva, Luiz B.; Dane, C. Brent; Mrowka, Stanley

    1999-11-16

    A compact laser system that removes surface coatings (such as paint, dirt, etc.) at a removal rate as high as 1000 ft.sup.2 /hr or more without damaging the surface. A high repetition rate laser with multiple amplification passes propagating through at least one optical amplifier is used, along with a delivery system consisting of a telescoping and articulating tube which also contains an evacuation system for simultaneously sweeping up the debris produced in the process. The amplified beam can be converted to an output beam by passively switching the polarization of at least one amplified beam. The system also has a personal safety system which protects against accidental exposures.

  12. Strategies for adapting to high rates of employee turnover.

    Science.gov (United States)

    Mowday, R T

    1984-01-01

    For many organizations facing high rates of employee turnover, strategies for increasing employee retention may not be practical because employees leave for reasons beyond the control of management or the costs of reducing turnover exceed the benefits to be derived. In this situation managers need to consider strategies that can minimize or buffer the organization from the negative consequences that often follow from turnover. Strategies organizations can use to adapt to uncontrollably high employee turnover rates are presented in this article. In addition, suggestions are made for how managers should make choices among the alternative strategies.

  13. Influence of pseudorandom bit format on the direct modulation performance of semiconductor lasers

    Indian Academy of Sciences (India)

    Moustafa Ahmed; Safwat W Z Mahmoud; Alaa A Mohmoud

    2012-12-01

    This paper investigates the direct gigabit modulation characteristics of semiconductor lasers using the return to zero (RZ) and non-return to zero (NRZ) formats. The modulation characteristics include the frequency chirp, eye diagram, and turn-on jitter (TOJ). The differences in the relative contributions of the intrinsic noise of the laser and the pseudorandom bit-pattern effect to the modulation characteristics are presented. We introduce an approximate estimation to the transient properties that control the digital modulation performance, namely, the modulation bit rate and the minimum (setting) bit rate required to yield a modulated laser signal free from the bit pattern effect. The results showed that the frequency chirp increases with the increase of the modulation current under both RZ and NRZ formats, and decreases remarkably with the increase of the bias current. The chirp is higher under the RZ modulation format than under the NRZ format. When the modulation bit rate is higher than the setting bit rate of the relaxation oscillation, the laser exhibits enhanced TOJ and the eye diagram is partially closed. TOJ decreases with the increase of the bias and/or modulation current for both formats of modulation.

  14. 39 fJ/bit On-Chip Identification ofWireless Sensors Based on Manufacturing Variation

    Directory of Open Access Journals (Sweden)

    Jonathan F. Bolus

    2014-09-01

    Full Text Available A 39 fJ/bit IC identification system based on FET mismatch is presented and implemented in a 130 nm CMOS process. ID bits are generated based on the ΔVT between identically drawn NMOS devices due to manufacturing variation, and the ID cell structure allows for the characterization of ID bit reliability by characterizing ΔVT . An addressing scheme is also presented that allows for reliable on-chip identification of ICs in the presence of unreliable ID bits. An example implementation is presented that can address 1000 unique ICs, composed of 31 ID bits and having an error rate less than 10-6, with up to 21 unreliable bits.

  15. Switching field distribution of exchange coupled ferri-/ferromagnetic composite bit patterned media

    CERN Document Server

    Oezelt, Harald; Fischbacher, Johann; Matthes, Patrick; Kirk, Eugenie; Wohlhüter, Phillip; Heyderman, Laura Jane; Albrecht, Manfred; Schrefl, Thomas

    2016-01-01

    We investigate the switching field distribution and the resulting bit error rate of exchange coupled ferri-/ferromagnetic bilayer island arrays by micromagnetic simulations. Using islands with varying microstructure and anisotropic properties, the intrinsic switching field distribution is computed. The dipolar contribution to the switching field distribution is obtained separately by using a model of a hexagonal island array resembling $1.4\\,\\mathrm{Tb/in}^2$ bit patterned media. Both contributions are computed for different thickness of the soft exchange coupled ferrimagnet and also for ferromagnetic single phase FePt islands. A bit patterned media with a bilayer structure of FeGd($5\\,\\mathrm{nm}$)/FePt($5\\,\\mathrm{nm}$) shows a bit error rate of $10^{-4}$ with a write field of $1.2\\,\\mathrm{T}$.

  16. Secure and Efficient Pseudorandom Bit Generator for Chaotic Stream Ciphers

    Institute of Scientific and Technical Information of China (English)

    WANG Xiao-Min; ZHANG Jia-Shu

    2007-01-01

    Based on the entropy criterion and n-dimensional uniform distribution of nonlinear digital filter (NDF), we present an efficient NDF-based pseudorandom bit generator (NDF-PRBG) for chaotic stream ciphers. The cryptographic properties of the proposed NDF-PRBG are analysed, and some experiments are made. The results show that it has desirable cryptographic properties, and can be used to construct secure stream ciphers with high speed.

  17. Pulse shaping for high data rate ultra-wideband wireless transmission under the Russian spectral emission mask

    DEFF Research Database (Denmark)

    Rommel, Simon; Grakhova, Elizaveta P.; Jurado-Navas, Antonio

    2017-01-01

    This paper addresses impulse-radio ultra-wideband (IR-UWB) transmission under the Russian spectral emission mask for unlicensed UWB radio communications. Four pulse shapes are proposed and their bit error rate (BER) performance is both estimated analytically and evaluated experimentally. Well-kno...

  18. User microprogrammable processors for high data rate telemetry preprocessing

    Science.gov (United States)

    Pugsley, J. H.; Ogrady, E. P.

    1973-01-01

    The use of microprogrammable processors for the preprocessing of high data rate satellite telemetry is investigated. The following topics are discussed along with supporting studies: (1) evaluation of commercial microprogrammable minicomputers for telemetry preprocessing tasks; (2) microinstruction sets for telemetry preprocessing; and (3) the use of multiple minicomputers to achieve high data processing. The simulation of small microprogrammed processors is discussed along with examples of microprogrammed processors.

  19. Low complexity bit loading algorithm for OFDM system

    Institute of Scientific and Technical Information of China (English)

    Yang Yu; Sha Xuejun; Zhang Zhonghua

    2006-01-01

    A new approach to loading for orthogonal frequency division multiplexing (OFDM) system is proposed, this bit-loading algorithm assigns bits to different subchannels in order to minimize the transmit energy. In the algorithm,first most bit are allocated to each subchannels according to channel condition, Shannon formula and QoS require of the user, then the residual bit are allocated to the subchannels bit by bit. In this way the algorithm is efficient while calculation is less complex. This is the first time to load bits with the scale following Shannon formula and the algorithm is of O (4N) complexity.

  20. Pedalling rate affects endurance performance during high-intensity cycling

    DEFF Research Database (Denmark)

    Nielsen, Jens Steen; Hansen, Ernst Albin; Sjøgaard, Gisela

    2004-01-01

    , such as muscle fibre type composition and power reserve, relate to endurance time. Twenty males underwent testing to determine their maximal oxygen uptake (VO(2max)), power output corresponding to 90% of VO(2max) at 80 rpm (W90), FCPR at W90, percentage of slow twitch muscle fibres (% MHC I), maximal leg power...... time was negatively related to VO(2max), W90 and % MHC I, while positively related to power reserve. In conclusion, at group level, endurance time was longer at FCPR and at a pedalling rate 25% lower compared to a pedalling rate 25% higher than FCPR. Further, inter-individual physiological variables......The purpose of this study into high-intensity cycling was to: (1) test the hypothesis that endurance time is longest at a freely chosen pedalling rate (FCPR), compared to pedalling rates 25% lower (FCPR-25) and higher (FCPR+25) than FCPR, and (2) investigate how physiological variables...