Challenges in global ballast water management

International Nuclear Information System (INIS)

Endresen, Oyvind; Lee Behrens, Hanna; Brynestad, Sigrid; Bjoern Andersen, Aage; Skjong, Rolf

2004-01-01

Ballast water management is a complex issue raising the challenge of merging international regulations, ship's specific configurations along with ecological conservation. This complexity is illustrated in this paper by considering ballast water volume, discharge frequency, ship safety and operational issues aligned with regional characteristics to address ecological risk for selected routes. A re-estimation of ballast water volumes gives a global annual level of 3500 Mton. Global ballast water volume discharged into open sea originating from ballast water exchange operations is estimated to approximately 2800 Mton. Risk based decision support systems coupled to databases for different ports and invasive species characteristics and distributions can allow for differentiated treatment levels while maintaining low risk levels. On certain routes, the risk is estimated to be unacceptable and some kind of ballast water treatment or management should be applied

Modelling Ballast Water Transport

Digital Repository Service at National Institute of Oceanography (India)

Jayakumar, S.; Babu, M.T.; Vethamony, P.

Ballast water discharges in the coastal environs have caused a great concern over the recent periods as they account for transporting marine organisms from one part of the world to the other. The movement of discharged ballast water as well...

Ras promotes cell survival by antagonizing both JNK and Hid signals in the Drosophila eye.

Science.gov (United States)

Wu, Yue; Zhuang, Yuan; Han, Min; Xu, Tian; Deng, Kejing

2009-10-20

Programmed cell death, or apoptosis, is a fundamental physiological process during normal development or in pathological conditions. The activation of apoptosis can be elicited by numerous signalling pathways. Ras is known to mediate anti-apoptotic signals by inhibiting Hid activity in the Drosophila eye. Here we report the isolation of a new loss-of-function ras allele, rasKP, which causes excessive apoptosis in the Drosophila eye. This new function is likely to be mediated through the JNK pathway since the inhibition of JNK signalling can significantly suppress rasKP-induced apoptosis, whereas the removal of hid only weakly suppresses the phenotype. Furthermore, the reduction of JNK signalling together with the expression of the baculovirus caspase inhibitor p35, which blocks Hid activity, strongly suppresses the rasKP cell death. In addition, we find a strong correlation between rasKP-induced apoptosis in the eye disc and the activation of JNK signalling. In the Drosophila eye, Ras may protect cells from apoptosis by inhibiting both JNK and Hid activities. Surprisingly, reducing Ras activity in the wing, however, does not cause apoptosis but rather affects cell and organ size. Thus, in addition to its requirement for cell viability, Ras appears to mediate different biological roles depending on the developmental context and on the level of its expression.

Autosomal SNP typing of forensic samples with the GenPlex(TM) HID System: Results of a collaborative study

DEFF Research Database (Denmark)

Tomas, C.; Axler-DiPerte, G.; Budimlija, Z.M.

2011-01-01

in Europe and 5 in the US) in order to test the robustness and reliability of the GenPlex(TM) HID System on forensic samples. Three samples with partly degraded DNA and 10 samples with low amounts of DNA were analyzed in duplicates using various amounts of DNA. In order to compare the performance of the Gen......Plex(TM) HID System with the most commonly used STR kits, 500 pg of partly degraded DNA from three samples was typed by the laboratories using one or more STR kits. The median SNP typing success rate was 92.3% with 500 pg of partly degraded DNA. Three of the fourteen laboratories counted for more than two...... was the least successful. With the exception of the MiniFiler(TM) kit (AB), GenPlex(TM) HID performed better than five other tested STR kits. When partly degraded DNA was analyzed, GenPlex(TM) HID showed a very low mean mach probability, while all STR kits except MiniFiler(TM) had very limited discriminatory...

Investigating antennas as ignition aid for automotive HID lamps

International Nuclear Information System (INIS)

Bergner, A; Engelhardt, M; Bienholz, S; Ruhrmann, C; Hoebing, T; Groeger, S; Mentel, J; Awakowicz, P

2015-01-01

This paper considers the ignition of mercury-free high-intensity discharge (HID) lamps for car headlights. Due to safety reasons, these lamps need to have a fast run-up phase which is ensured, amongst other things, by a high Xe pressure of roughly 15 bar (cold) in the discharge vessel. The high Xe pressure causes an increased ignition voltage compared with former mercury-containing automotive HID lamps or low-pressure lamps used for general-lighting applications. The increase in ignition voltage can be limited if the electric field in front of the electrodes is raised by an uplifting of the electrical conductivity along the outer wall of the inner bulb either by a conductive layer on its surface or by a dielectric barrier discharge (DBD) within the outer bulb. This paper considers on the one hand conventional antennas deposited by physical vapour deposition (PVD) and on the other hand a combination of these antennas with a DBD within the outer-bulb operated in 100 mbar Ar as ignition aids. In both cases the antenna potential and antenna width are varied. Additionally, the effects of antenna thickness and antenna material are investigated. The ignition voltage, ignition current and light emission during ignition are measured on a nanosecond timescale. Furthermore, for the very first time, the ignition process is recorded in four consecutive intensified charge-coupled device images using a high-speed camera system with a time resolution in the range of nanoseconds. It was found that antennas strongly reduce the ignition voltage of automotive HID lamps. Active antennas reduce the ignition voltage significantly more than passive antennas, proportional to the conductance of the antenna. Combining conventional antennas with an outer-bulb discharge reduces the ignition voltage from 19 kV without any ignition aid to the intrinsic ignition voltage of the lamp below 10 kV, in the best case. (paper)

Application of geocomposite placed beneath ballast bed to improve ballast quality and track stability

Science.gov (United States)

Horníček, Leoš; Břešt'ovský, Petr; Jasanský, Petr

2017-09-01

The article deals with the application of a stabilization hexagonal geocomposite for the improvement of poor stability of railway tracks caused by undesirable migration of fine soil particles from the subgrade into the ballast bed. The establishment of a test railway section on a single-line track situated near Domazlice and its long-term monitoring programme are described. Evaluation is aimed especially at track geometry parameters, the load-bearing capacity of the ballast bed, elastic rail deflection during train passages and the durability of geocomposite’s physical properties. The data taken from the test section during five measurement campaigns are compared with both adjacent sections. In one of them, only the ballast bed renovation was carried out, whereas in the second one no intervention was performed at all. The usage of a pioneering geosynthetic product in combination with new trends in ballast bed restoration seems to be an innovative as well as effective solution to analogous problematic spots on railway tracks in the Czech Republic.

Treating PCB contaminated light ballasts

International Nuclear Information System (INIS)

Day, B.

1995-01-01

Development and salient features of CON TECH PCB, a light ballast reduction process to allow PCB waste owners to best utilize storage space for the long-term regulated storage of PCBs, or to prepare them for final destruction and to reduce destruction costs, was reviewed. The essence of the process is ballast splitting, i.e. the breaking of the ballast and removing the capacitor containing the toxic PCBs. The work is done in a specially fitted mobile processing unit, thus reducing the storage requirements by better than 50 per cent. Details of the process and some cost and storage facility estimates were provided

Effect of a pulsed power supply on the spectral and electrical characteristics of HID lamps

International Nuclear Information System (INIS)

Chammam, Abdeljelil; Elloumi, Hatem; Mrabet, Brahim; Charrada, Kamel; Stambouli, Mongi; Damelincourt, Jean Jacques

2005-01-01

Results of spectral and photometric measurements are presented for pulsed power operated high intensity discharges (HIDs). This investigation is related to the application of a pulsed power supply for pile driving of HID lamps. Specifically, we are interested in controlling the spectral response radiation of visible and ultraviolet (UV) lines for tertiary treatment of water using UV radiation. Simulations based on a physical model of the lamps were conducted. These results relate to the radial temperature, line intensity and electrical properties (voltage, power and conductivity). Good agreement has been found between the results of the simulations and the experimental findings

Emerging risks from ballast water treatment: The run-up to the International Ballast Water Management Convention

NARCIS (Netherlands)

Werschkun, B.; Banerji, S.; Basurko, O.C.; David, M.; Fuhr, F; Gollasch, S.; Grummt, T.; Haarich, M.; Jha, A.N.; Kacan, S.; Kehrer, A.; Linders, J.; Mesbahi, E.; Pughiuc, D.; Richardson, S.D.; Schwarz-Schulz, B.; Shah, A.; Theobald, N.; von Gunten, U.; Wieck, S.; Hofer, T.

2014-01-01

Uptake and discharge of ballast water by ocean-going ships contribute to the worldwide spread of aquatic invasive species, with negative impacts on the environment, economies, and public health. The International Ballast Water Management Convention aims at a global answer. The agreed standards for

Ten years of Brazilian ballast water management

Science.gov (United States)

Castro, Maria Cecilia Trindade; Hall-Spencer, Jason M.; Poggian, Cecília Fonseca; Fileman, Timothy W.

2018-03-01

In 2005, Brazil addressed the environmental challenges posed by ballast water through a unilateral regulation, called the Maritime Standard N° 20 (NORMAM-20), applied to all shipping in her waters. This world-leading decision was the culmination of a process that started during the 1990‧s. Here, we summarize how these ballast water regulations were brought in and adopted and present the findings of 10 years of enforcement (2005-2015) in 39 ports along the Brazilian coast. We show that compliance with the Brazilian standard has increased significantly since the regulations were implemented (p < 0.001). After five years of implementation, non-compliance decreased probably reflecting an increase in awareness of the Brazilian Standard and a shift in the shipping industry commitment to minimize and control the spread of invasive species through ballast water. The Brazilian experience shows that very high levels (97%) of compliance with ballast water management regulations can be made to work in a region of global importance to the maritime industry. In the last decade, the rules governing ballast water in Brazil have evolved to address the demands from the maritime community and to provide updates such as imminent requirements for the use of ballast water management systems on board ships. These regulations are rarely cited when ballast water regulations are discussed internationally, yet there is much to learn from the proactive approach taken by Brazil such as what is feasible and enforceable.

33 CFR 401.30 - Ballast water and trim.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 3 2010-07-01 2010-07-01 false Ballast water and trim. 401.30... OF TRANSPORTATION SEAWAY REGULATIONS AND RULES Regulations Seaway Navigation § 401.30 Ballast water... exclusive economic zone must agree to comply with the “Code of Best Practices for Ballast Water Management...

Macroalgal survival in ballast water tanks

International Nuclear Information System (INIS)

Flagella, Maria Monia; Verlaque, Marc; Soria, Alessio; Buia, Maria Cristina

2007-01-01

Despite a large amount of research into invasive species and their introductions, there have been no studies focused on macroalgal transport in ballast water. To address this, we collected replicate samples of ballast water from 12 ships in two Mediterranean harbours (Naples and Salerno). Filtered samples were kept in culture for a month at Mediterranean mean conditions (18 deg. C, 12:12 h LD, 60 μmol photons m -2 s -1 ). Fifteen macroalgal taxa were cultured and differed according to the geographic origin of the ballast water. Most of the cultured algae were widely distributed species (e.g. Ulva spp. and Acinetospora-phase). However, Ulva ohnoi Hiraoka and Shimada, described from Japan, was hitherto unknown in the Mediterranean Sea. We show for the first time that ballast water can be an important vector for the transport of microscopic stages of macroalgae and that this can be a vector for the introduction of alien species

Macroalgal survival in ballast water tanks

Energy Technology Data Exchange (ETDEWEB)

Flagella, Maria Monia [Benthic Ecology Laboratory, Stazione Zoologica A. Dohrn, P.ta S.Pietro, 80077, Ischia, Naples (Italy)], E-mail: flagella@szn.it; Verlaque, Marc [UMR 6540 DIMAR, COM, Universite de la Mediterranee, 13288 Marseille Cedex 9 (France); Soria, Alessio; Buia, Maria Cristina [Benthic Ecology Laboratory, Stazione Zoologica A. Dohrn, P.ta S.Pietro, 80077, Ischia, Naples (Italy)

2007-09-15

Despite a large amount of research into invasive species and their introductions, there have been no studies focused on macroalgal transport in ballast water. To address this, we collected replicate samples of ballast water from 12 ships in two Mediterranean harbours (Naples and Salerno). Filtered samples were kept in culture for a month at Mediterranean mean conditions (18 deg. C, 12:12 h LD, 60 {mu}mol photons m{sup -2} s{sup -1}). Fifteen macroalgal taxa were cultured and differed according to the geographic origin of the ballast water. Most of the cultured algae were widely distributed species (e.g. Ulva spp. and Acinetospora-phase). However, Ulva ohnoi Hiraoka and Shimada, described from Japan, was hitherto unknown in the Mediterranean Sea. We show for the first time that ballast water can be an important vector for the transport of microscopic stages of macroalgae and that this can be a vector for the introduction of alien species.

Optimisation of bitumen emulsion properties for ballast stabilisation

International Nuclear Information System (INIS)

D’Angelo, G.; Lo Presti, D.; Thom, N.

2017-01-01

Ballasted track, while providing economical and practical advantages, is associated with high costs and material consumption due to frequent maintenance. More sustainable alternatives to conventional ballasted trackbeds should therefore aim at extending its durability, particularly considering ongoing increases in traffic speed and loads. In this regard, the authors have investigated a solution consisting of bitumen stabilised ballast (BSB), designed to be used for new trackbeds as well as in reinforcing existing ones. This study presents the idea behind the technology and then focuses on a specific part of its development: the optimisation of bitumen emulsion properties and dosage in relation to ballast field conditions. Results showed that overall bitumen stabilisation improved ballast resistance to permanent deformation by enhancing stiffness and damping properties. Scenarios with higher dosage of bitumen emulsion, higher viscosity, quicker setting behaviour, and harder base bitumen seem to represent the most desirable conditions to achieve enhanced in-field performance. [es

Economical weight loss program for PCB-contaminated ballasts

International Nuclear Information System (INIS)

Day, B.

1995-01-01

A PCB (Polychlorinated Biphenyls) reduction process for PCB-contaminated ballasts was described. The process was developed by such organizations and programs as PCB Containment Technology Inc, and the Contech Ballast Reduction Program, and was claimed to include waste reduction of lighting ballasts down to their smallest PCB contaminated components. Particular attention was paid to the two most contaminated main components, i.e. the capacitor and the tar potting material. Development of the process and the government's role and participation therein was explained. The process of ballast reduction was said to utilize the old 'Reduce, Reuse and Recycle' theory; it was considered to be a cost effective waste reduction, recycling, and auditing alternative to incineration of PCBs

Application of hydrodynamic cavitation in ballast water treatment.

Science.gov (United States)

Cvetković, Martina; Kompare, Boris; Klemenčič, Aleksandra Krivograd

2015-05-01

Ballast water is, together with hull fouling and aquaculture, considered the most important factor of the worldwide transfer of invasive non-indigenous organisms in aquatic ecosystems and the most important factor in European Union. With the aim of preventing and halting the spread of the transfer of invasive organisms in aquatic ecosystems and also in accordance with IMO's International Convention for the Control and Management of Ships Ballast Water and Sediments, the systems for ballast water treatment, whose work includes, e.g. chemical treatment, ozonation and filtration, are used. Although hydrodynamic cavitation (HC) is used in many different areas, such as science and engineering, implied acoustics, biomedicine, botany, chemistry and hydraulics, the application of HC in ballast water treatment area remains insufficiently researched. This paper presents the first literature review that studies lab- and large-scale setups for ballast water treatment together with the type-approved systems currently available on the market that use HC as a step in their operation. This paper deals with the possible advantages and disadvantages of such systems, as well as their influence on the crew and marine environment. It also analyses perspectives on the further development and application of HC in ballast water treatment.

Assessment of didecyldimethylammonium chloride as a ballast water treatment method

NARCIS (Netherlands)

van Slooten, Cees; Buma, Anita; Peperzak, Louis

Ballast water-mediated transfer of aquatic invasive species is considered a major threat to marine biodiversity, marine industry and human health. A ballast water treatment is needed to comply with International Maritime Organization (IMO) ballast water discharge regulations. Didecyldimethylammonium

Assessment of didecyldimethylammonium chloride as a ballast water treatment method

NARCIS (Netherlands)

van Slooten, C.; Peperzak, L.; Buma, A.G.J.

2015-01-01

Ballast water-mediated transfer of aquatic invasive species is considered a major threat to marine biodiversity, marine industry and human health. A ballast water treatment is needed to comply with International Maritime Organization (IMO) ballast water discharge regulations. Didecyldimethylammonium

Inerting ballast tanks

Energy Technology Data Exchange (ETDEWEB)

Baes, Gabriel L.; Bronneberg, Jos [SBM Offshore, AA Schiedam (Netherlands); Barros, Maria A.S.D. de [Universidade Estadual de Maringa (UEM), PR (Brazil)

2012-07-01

This report expands upon the work conducted by SBM Offshore to develop a tank preservation treatment, which is intended to achieve a service life of 30 years. This work focuses on the corrosion problems, in the ballast tanks, based on new built hulls, both for the Gas Exploration Market, the FLNG - Floating Liquefied Natural Gas, and for the Oil Exploration market - FPSO's - Floating Production Storage and offloading Units. Herein, the corrosion rate input comes from the various references related to the process of nitrogen injection, which is expected to extend the vessel's time life. The essential elements of this solution comprise the deoxygenation process, corrosion models, coating effects, tests from laboratory, shipboard tests, corrosion institutes and regulations applicable to the operation. The best corrosion protection system for ballast tanks area combines a coating system and an inert gas system. The condition of the tanks will be dependent upon the level of protection applied to the steel structure, including, but not limited to coating, cathodic protection, etc. There is a need for products which extend the life time. It is not sufficient, only have good theoretical base for the corrosion and an excellent treatment system. In addition, the design of the ships structure must also eliminate the presence of local stress concentrations which can result in fatigue cracking and rupture of the protective coating barrier starting the corrosion. As a direct result of this, more problems in corrosion can be mitigated, vessels can have a better corrosion performance with less maintenance and repairs to coating systems in ballast tanks. Furthermore ships will be positively impacted operationally due to less frequent dry docking. There is a huge potential in the application of inert gas to combat the corrosion rate inside the ballast tanks, one of the most corrosive environments on earth. This application can have a direct impact on vessel structure

WET-tests on UV-treated ballast water

NARCIS (Netherlands)

Kaag, N.H.B.M.

2015-01-01

Damen Shipyards has developed a barge-based ballast water management system (BWMS) that enables direct treatment of ballast water during discharge in a receiving harbour. The treatment is based upon filtration and a once-through UV-treatment. As part of the Type Approval process, the Dutch

Statistical analysis of cone penetration resistance of railway ballast

Directory of Open Access Journals (Sweden)

Saussine Gilles

2017-01-01

Full Text Available Dynamic penetrometer tests are widely used in geotechnical studies for soils characterization but their implementation tends to be difficult. The light penetrometer test is able to give information about a cone resistance useful in the field of geotechnics and recently validated as a parameter for the case of coarse granular materials. In order to characterize directly the railway ballast on track and sublayers of ballast, a huge test campaign has been carried out for more than 5 years in order to build up a database composed of 19,000 penetration tests including endoscopic video record on the French railway network. The main objective of this work is to give a first statistical analysis of cone resistance in the coarse granular layer which represents a major component of railway track: the ballast. The results show that the cone resistance (qd increases with depth and presents strong variations corresponding to layers of different natures identified using the endoscopic records. In the first zone corresponding to the top 30cm, (qd increases linearly with a slope of around 1MPa/cm for fresh ballast and fouled ballast. In the second zone below 30cm deep, (qd increases more slowly with a slope of around 0,3MPa/cm and decreases below 50cm. These results show that there is no clear difference between fresh and fouled ballast. Hence, the (qd sensitivity is important and increases with depth. The (qd distribution for a set of tests does not follow a normal distribution. In the upper 30cm layer of ballast of track, data statistical treatment shows that train load and speed do not have any significant impact on the (qd distribution for clean ballast; they increase by 50% the average value of (qd for fouled ballast and increase the thickness as well. Below the 30cm upper layer, train load and speed have a clear impact on the (qd distribution.

Management and environmental risk study of the physicochemical parameters of ballast water

International Nuclear Information System (INIS)

Nosrati-Ghods, Nosaibeh; Ghadiri, Mehdi; Früh, Wolf-Gerrit

2017-01-01

Shipping is a vital industry for the global economy. Stability of ships, provided by ballast water, is a crucial factor for cargo loading and unloading processes. Ballast water treatment has practical significance in terms of environmental issues, ecosystem, and human health, because ships discharge this water into the environment before loading their cargos. This study reviews the common methods for ballast water management – exchange, heating, filtration, ultrasonic treatment, ultraviolet irradiation, chemicals, and gas supersaturation – to select the best one. This study compares water temperature, salinity, dissolved oxygen, polycyclic aromatic hydrocarbons (PAHs), and heavy metals (Co, Cr, Ni, Pb) for ballast tanks of selected ships with the recipient port environment in the Persian Gulf as a case study. The exchange of ballast water in the ocean and/or its treatment on board to prevent inadvertent effects on the environment's physicochemical conditions is related to vessel characteristics, legislation, and the environmental condition. Ecological risk study showed that the salt content in ballast water is close to that of seawater, but the values of Cr (2.1 mg/l) and Ni (0.029 mg/l) in ballast water are higher than those in seawater (1 and 0.004 mg/l, respectively). - Highlights: • Description of ballast water management methods. • Experimental investigation of ballast water and seawater. • Differences of physiochemical characteristics of ballast water and seawater. • Selection of the best ballast water management method.

Influence of an additional ballast volume on a pulsed ICP discharge

International Nuclear Information System (INIS)

Bogdanov, E A; Jr, C A DeJoseph; Demidov, V I; Kudryavtsev, A A; Serditov, K Yu

2007-01-01

A spatial and temporal numerical simulation has been carried out of a pulsed (100% modulated), rf inductively coupled plasma discharge in argon, connected to an additional (ballast) diffusion chamber of much larger volume. It is demonstrated that during the active phase, the presence of the large ballast volume has a small impact on the parameters of the plasma in the smaller discharge chamber. In this case the plasma parameters in the discharge chamber can be estimated separately from the diffusion chamber by a standard method using the characteristic ambipolar diffusion time (for example, using a global model). However, during the afterglow phase, the situation is changed significantly. In the afterglow, the densities of charged particles in the discharge chamber become lower than in the large ballast chamber due to more rapid diffusion loss. As a result, the reverse of the active phase situation occurs, namely, the plasma does not flow from the small to the large chamber, but in the opposite direction, from diffusive to discharge volume, and both the plasma density gradient and the self-consistent ambipolar electric field in the small chamber change directions. This phenomenon leads to new effects in the discharge volume, in particular a decreasing rate of decay of densities of charged particles and electron temperature. Thus, in the afterglow the presence of a large additional ballast volume has a significant impact on the plasma transport. In this case, a simple treatment of the plasma in the discharge chamber in the framework of a spatially averaged model (for example, the global model) is inadequate

Nanos-mediated repression of hid protects larval sensory neurons after a global switch in sensitivity to apoptotic signals.

Science.gov (United States)

Bhogal, Balpreet; Plaza-Jennings, Amara; Gavis, Elizabeth R

2016-06-15

Dendritic arbor morphology is a key determinant of neuronal function. Once established, dendrite branching patterns must be maintained as the animal develops to ensure receptive field coverage. The translational repressors Nanos (Nos) and Pumilio (Pum) are required to maintain dendrite growth and branching of Drosophila larval class IV dendritic arborization (da) neurons, but their specific regulatory role remains unknown. We show that Nos-Pum-mediated repression of the pro-apoptotic gene head involution defective (hid) is required to maintain a balance of dendritic growth and retraction in class IV da neurons and that upregulation of hid results in decreased branching because of an increase in caspase activity. The temporal requirement for nos correlates with an ecdysone-triggered switch in sensitivity to apoptotic stimuli that occurs during the mid-L3 transition. We find that hid is required during pupariation for caspase-dependent pruning of class IV da neurons and that Nos and Pum delay pruning. Together, these results suggest that Nos and Pum provide a crucial neuroprotective regulatory layer to ensure that neurons behave appropriately in response to developmental cues. © 2016. Published by The Company of Biologists Ltd.

Chemical and mineralogical characterization of silicon manganese iron slag as railway ballast

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Ralph Werner Heringer; Barreto, Rairane Aparecida, E-mail: ralph@em.ufop.br, E-mail: rairanebarreto@hotmail.com [Universidade Federal de Ouro Preto (UFOP), MG (Brazil); Fernandes, Gilberto, E-mail: gilberto@unicerp.edu.br [Centro Universitário do Cerrado Patrocínio (UNICERP), Patrocínio, MG (Brazil); Sousa, Fabiano Carvalho, E-mail: fabiano.carvalho.sousa@vale.com [Vale, Belo Horizonte, MG (Brazil)

2017-10-15

In nature, metal ores such as iron, lead, aluminum and others are found in an impure state, sometimes oxidized and mixed with silicates of other metals. During casting, when the ore is exposed to high temperatures, these impurities are separated from the molten metal and can be removed. The mass formed by these compounds is slag. Slag is the co-product of the smelting of ore to purify metals. It may be considered a mixture of metal oxides, but may also contain metal sulphites and metal atoms in their elemental form. After it is reprocessed to separate the metals contained, the co-products of this process can be used in cement, rail ballast, road paving and various other purposes. The objective of this research work is the presentation of the chemical and mineralogical characterization tests of the silicon-manganese iron slag with the purpose of reusing the coproduct as rail ballast. X-ray diffraction tests, quantitative chemical analyzes, scanning electron microscopy and free lime content were prepared for these characterizations. The results of these tests showed the technical feasibility of using slag as rail ballast. (author)

Chemical and mineralogical characterization of silicon manganese iron slag as railway ballast

International Nuclear Information System (INIS)

Oliveira, Ralph Werner Heringer; Barreto, Rairane Aparecida; Fernandes, Gilberto; Sousa, Fabiano Carvalho

2017-01-01

In nature, metal ores such as iron, lead, aluminum and others are found in an impure state, sometimes oxidized and mixed with silicates of other metals. During casting, when the ore is exposed to high temperatures, these impurities are separated from the molten metal and can be removed. The mass formed by these compounds is slag. Slag is the co-product of the smelting of ore to purify metals. It may be considered a mixture of metal oxides, but may also contain metal sulphites and metal atoms in their elemental form. After it is reprocessed to separate the metals contained, the co-products of this process can be used in cement, rail ballast, road paving and various other purposes. The objective of this research work is the presentation of the chemical and mineralogical characterization tests of the silicon-manganese iron slag with the purpose of reusing the coproduct as rail ballast. X-ray diffraction tests, quantitative chemical analyzes, scanning electron microscopy and free lime content were prepared for these characterizations. The results of these tests showed the technical feasibility of using slag as rail ballast. (author)

Detection of Ballast Damage by In-Situ Vibration Measurement of Sleepers

Science.gov (United States)

Lam, H. F.; Wong, M. T.; Keefe, R. M.

2010-05-01

Ballasted track is one of the most important elements of railway transportation systems worldwide. Owing to its importance in railway safety, many monitoring and evaluation methods have been developed. Current railway track monitoring systems are comprehensive, fast and efficient in testing railway track level and alignment, rail gauge, rail corrugation, etc. However, the monitoring of ballast condition still relies very much on visual inspection and core tests. Although extensive research has been carried out in the development of non-destructive methods for ballast condition evaluation, a commonly accepted and cost-effective method is still in demand. In Hong Kong practice, if abnormal train vibration is reported by the train operator or passengers, permanent way inspectors will locate the problem area by track geometry measurement. It must be pointed out that visual inspection can only identify ballast damage on the track surface, the track geometry deficiencies and rail twists can be detected using a track gauge. Ballast damage under the sleeper loading area and the ballast shoulder, which are the main factors affecting track stability and ride quality, are extremely difficult if not impossible to be detected by visual inspection. Core test is a destructive test, which is expensive, time consuming and may be disruptive to traffic. A fast real-time ballast damage detection method that can be implemented by permanent way inspectors with simple equipment can certainly provide valuable information for engineers in assessing the safety and riding quality of ballasted track systems. The main objective of this paper is to study the feasibility in using the vibration characteristics of sleepers in quantifying the ballast condition under the sleepers, and so as to explore the possibility in developing a handy method for the detection of ballast damage based on the measured vibration of sleepers.

The challenges and promises of genetic approaches for ballast water management

Science.gov (United States)

Rey, Anaïs; Basurko, Oihane C.; Rodríguez-Ezpeleta, Naiara

2018-03-01

Ballast water is a main vector of introduction of Harmful Aquatic Organisms and Pathogens, which includes Non-Indigenous Species. Numerous and diversified organisms are transferred daily from a donor to a recipient port. Developed to prevent these introduction events, the International Convention for the Control and Management of Ships' Ballast Water and Sediments will enter into force in 2017. This international convention is asking for the monitoring of Harmful Aquatic Organisms and Pathogens. In this review, we highlight the urgent need to develop cost-effective methods to: (1) perform the biological analyses required by the convention; and (2) assess the effectiveness of two main ballast water management strategies, i.e. the ballast water exchange and the use of ballast water treatment systems. We have compiled the biological analyses required by the convention, and performed a comprehensive evaluation of the potential and challenges of the use of genetic tools in this context. Following an overview of the studies applying genetic tools to ballast water related research, we present metabarcoding as a relevant approach for early detection of Harmful Aquatic Organisms and Pathogens in general and for ballast water monitoring and port risk assessment in particular. Nonetheless, before implementation of genetic tools in the context of the ballast water management convention, benchmarked tests against traditional methods should be performed, and standard, reproducible and easy to apply protocols should be developed.

Development and optimization of a matrix converter supplying an electronic ballast - UV lamp system for water sterilization

Science.gov (United States)

Bokhtache, Aicha Aissa; Zegaoui, Abdallah; Aillerie, Michel; Djahbar, Abdelkader; Hemici, Kheira

2018-05-01

Electronic ballasts dedicated to discharge lamps allow improving the quality of radiation by operating at high frequency. In the present work, the use of a single-phase direct converter with a matrix structure for supplying a low-pressure mercury-argon UVC lamp for water sterilization is proposed. The structure of the converter is based on two switching cells allowing the realization of a fully controllable bidirectional switches. The advantages of such a matrix topology include the delivered of a sinusoidal waveform current with a controllable power factor close to unity, variable in amplitude and frequency. In order to obtain the desired amplitude and frequency, a PWM control was associated in the current realization. Finally, a linear adjustment of the lamp arc current was warranted by using of a PI regulator.

Ballast Water Treatment, U.S. Great Lakes Bulk Carrier Engineering and Cost Study. Volume 2: Analysis of On-Board Treatment Methods, Alternative Ballast Water Management Practices, and Implementation Costs

Science.gov (United States)

2013-11-01

on discharge 3 CleanBallast Ballast Water Management System RWO Marine Water Technology 55 μm automatic back-flushing disc filter, electrolysis ...did not independently validate manufacturers’ claims. BWT technologies which apply electric current to ballast water ( electrolysis ) are affected by low...salinity prior to electrolysis , and the feed water must be preheated when the ballast water temperatures drop below 15 ºC. 1. Power Consumption

Electrochemical disinfection of simulated ballast water on PbO2/graphite felt electrode

International Nuclear Information System (INIS)

Chen, Shuiping; Hu, Weidong; Hong, Jianxun; Sandoe, Steve

2016-01-01

A novel PbO 2 /graphite felt electrode was constructed by electrochemical deposition of PbO 2 on graphite felt and characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM) analysis. The prepared electrode is a viable technology for inactivation of Escherichia coli, Enterococcus faecalis, and Artemia salina as indicator organisms in simulated ballast water treatment, which meets the International Maritime Organization (IMO) Regulation D-2. The effects of contact time and current density on inactivation were investigated. An increase in current density generally had a beneficial effect on the inactivation of the three species. E.faecalis and A.salina were more resistant to electrochemical disinfection than E. coli. The complete disinfection of E.coli was achieved in <8 min at an applied current density of 253 A/m 2 . Complete inactivation of E. faecalis and A.salina was achieved at the same current density after 60 and 40 min of contact time, respectively. A. salina inactivation follows first-order kinetics. - Highlights: •A novel PbO 2 /graphite felt anode was developed for the electrochemical treatment of the simulated ballast water. •The technology meets the IMO D‐2 regulation and provides a high degree of removal of the microorganisms of ballast water without any additional chemical substances. •E.faecalis, E.coli, and A.salina cells in simulated ballast water were completely inactivated after 60, 8 and 40 min of contact time at 253 A/m 2 of current density, respectively.

KPI (KEY PERFORMANCE INDICATORS APPLICATION ON BALLAST WATER TREATMENT SYSTEM SELECTION

Directory of Open Access Journals (Sweden)

Gülçin Vural

2017-01-01

Full Text Available Every day, more than 7,000 different marine species are transferred to different ecosystems via ballast water in ships. The introduction of invasive species can cause problems for native species. After realizing the serious potential problems associated with the transport of organisms in ballast water, national and international regulations were developed. In 2004, the International Maritime Organization introduced the International Convention for the Control and Management of Ships' Ballast Water and Sediments. With these regulations, the problems caused by ballast water have attracted attention and many companies have started to research and develop technologies for the management of ballast water. Today, there are hundreds of different systems for ballast-water treatment, and the selection of the most suitable system for a specific vessel is an increasingly important issue as the Convention nears enforcement on September 8, 2017. The goal of this study is to demonstrate that the application of key performance indicators (KPIs to the selection of a ballast-water treatment system (BWTS leads to a very useful tool with which shipyards can compare BWTSs. This allows them to make better choices and to designate the most suitable system for each of their ships. In this study, we examine two types of vessel from a shipyard in Istanbul, Turkey. They have different ballast-water capacities and equipment, and the most suitable system for each is selected by using the KPI method.

The Usage of Crumb Rubber Filtration and UV Radiation for Ballast Water Treatment

Directory of Open Access Journals (Sweden)

Trika Pitana

2017-12-01

Full Text Available This research is aimed to build ship’s ballast water treatment prototipe that used to inactivate microbial water patogen in ballast water to produce unpolluted ballast water that can be standardised by IMO Ballast Water Management Convention. A simple concept that used in the development of this prototype is by draining ballast water with capacity at 5 lpm, 10 lpm and 20 lpm into alternative filtration crumb rubber and UV reactor. In the filtration process using crumb rubber, ballast water will be filtered with the precision filtration up to 50 micron, while in the UV reactor ballast water will be illuminated by UV-C with maksimum dose 16,58 mW/cm2. Finally,the study shows the performance of alternative filtration of crumb rubber and UV-C irradiation on microbial water phatogen, and at what UV-C dose ballast water treatment prototipe can inactivate  microbial water phatogens, which are complying with IMO Ballast Water Management Convention ANNEX D. This research is aimed to build ship’s ballast water treatment prototipe that used to inactivate microbial water patogen in ballast water to produce unpolluted ballast water that can be standardised by IMO Ballast Water Management Convention. A simple concept that used in the development of this prototype is by draining ballast water with capacity at 5 lpm, 10 lpm and 20 lpm into alternative filtration crumb rubber and UV reactor. In the filtration process using crumb rubber, ballast water will be filtered with the precision filtration up to 50 micron, while in the UV reactor ballast water will be illuminated by UV-C with maksimum dose 16,58 mW/cm2. Finally,the study shows the performance of alternative filtration of crumb rubber and UV-C irradiation on microbial water phatogen, and at what UV-C dose ballast water treatment prototipe can inactivate  microbial water phatogens, which are complying with IMO Ballast Water Management Convention ANNEX D. Normal 0 false false false EN-US X-NONE X

Effectiveness of a Barge-Based Ballast Water Treatment System for Multi-Terminal Ports

Directory of Open Access Journals (Sweden)

Lovro Maglić

2015-10-01

Full Text Available The paper presents outcomes of the discrete event simulation of the ballast water management in a multi-terminal port. The simulation includes ship’s manoeuvring, cargo and ballast operations and a barge-based ballast water treatment system operating within all terminal areas. The barge-based ballast water treatment system is used by ships unable to use their own equipment, not equipped with an appropriate ballast treatment system or non-compliant with the Ballast Water Management (BWM Convention 2004 for whatever reason. The main goal is to estimate the productivity and cost effectiveness of such systems as an option to support ships not able to comply with the BWM Convention, once it enters into force. The model was built and tested in Arena simulation software. Process parameters are based on real traffic data for the port of Rijeka. The results indicate that barge-based ballast treatment facility will be heavily underutilized, and that such systems are cost-effective only in ports where large volumes of ballast water need to be delivered to shore treatment systems.

Compact Fluorescent Plug-In Ballast-in-a-Socket

Energy Technology Data Exchange (ETDEWEB)

Rebecca Voelker

2001-12-21

The primary goal of this program was to develop a ballast system for plug-in CFLs (compact fluorescent lamps) that will directly replace standard metal shell, medium base incandescent lampholders (such as Levition No. 6098) for use with portable lamp fixtures, such as floor, table and desk lamps. A secondary goal was to identify a plug-in CFL that is optimized for use with this ballast. This Plug-in CFL Ballastin-a-Socket system will allow fixture manufacturers to easily manufacture CFL-based high-efficacy portable fixtures that provide residential and commercial consumers with attractive, cost-effective, and energy-efficient fixtures for use wherever portable incandescent fixtures are used today. The advantages of this proposed system over existing CFL solutions are that the fixtures can only be used with high-efficacy CFLs, and they will be more attractive and will have lower life-cycle costs than screw-in or adapter-based CFL retrofit solutions. These features should greatly increase the penetration of CFL's into the North American market. Our work has shown that using integrated circuits it is quite feasible to produce a lamp-fixture ballast of a size comparable to the current Edison-screw 3-way incandescent fixtures. As for price points for BIAS-based fixtures, end-users polled by the Lighting Research Institute at RPI indicated that they would pay as much as an additional $10 for a lamp containing such a ballast. The ballast has been optimized to run with a 26 W amalgam triple biax lamp in the base-down position, yet can accept non-amalgam versions of the lamp. With a few part alterations, the ballast can be produced to support 32 W lamps as well. The ballast uses GE's existing L-Comp[1] power topology in the circuit so that the integrated circuit design would be a design that could possibly be used by other CFL and EFL products with minor modifications. This gives added value by reducing cost and size of not only the BIAS, but also possibly other

Chemical assessment of ballast water exchange compliance: Implementation in North America and New Zealand

Directory of Open Access Journals (Sweden)

Monaca eNoble

2016-05-01

Full Text Available Fluorescence by naturally occurring dissolved organic matter (FDOM is a sensitive indicator of ballast water source, with high FDOM in coastal ballast water decreasing typically dramatically when replaced by oceanic seawater during ballast water exchange. In this study, FDOM was measured in 92 ships arriving at Pacific ports on the US west coast and in New Zealand, and used to assess their compliance with ballast water regulations that required 95% replacement of port water to minimize invasive species risks. Fluorescence in many ships that reported ballast water exchange was significantly higher than is usual for oceanic seawater, and in several cases, significantly higher than in other ships with similar provenance and ballast water management. Pre-exchange source port conditions represented the largest source of uncertainty in the analysis, because residual coastal FDOM when highly fluorescent can significantly influence the fluorescence signature of exchanged ballast water. A meta-analysis comparing the intensities of FDOM in un-exchanged ballast tanks with calculated pre-exchange intensities assuming that ships all correctly implemented and reported ballast water exchange revealed notable discrepancies. Thus, the incidence of high-FDOM port waters was seven times lower in reality than would be expected on the basis of these calculations. The results suggest that a significant rate of reporting errors occur due to a combination of factors that may include inadequate ballast water exchange and unintentional or deliberate misreporting of ballast water management.

Ballast Water Treatment Test Facility

Data.gov (United States)

Federal Laboratory Consortium — FUNCTION: Provides functionality for the full-scale testing and controlled simulation of ship ballasting operations for assessment of aquatic nuisance species (ANS)...

Development of an electronic ballast with high power factor, using cd/cd conversion techniques for fluorescent lamps; Desarrollo de un balastro electronico con alto factor de potencia, utilizando tecnicas de conversion cd/cd para lamparas fluorescentes

Energy Technology Data Exchange (ETDEWEB)

Ortiz, Raul Antonio

1995-02-01

The recent advances and improvements in fluorescent lamps and ballasts technologies have resulted in substantial gain in efficiency, in illumination (lm/w), in the useful life of the lamp, in ballasts (electric characteristics), and consequently, an increase in energy saving in the fluorescent illumination systems. This thesis work was for the development of an electronic ballast that incorporates active correction of the PF for the handling of fluorescent lamps of the fast start type F4OW T-12. The prototype was implemented in two stages. In the first stage, for the Power Factor Correction (PFC) a converter CD/CD of the boost type in Continuous Conduction Mode (CCM) was chosen. The control technique that was used for this converter was the Average Current Mode (ACM) control. This thesis work comprised part of a collaboration project between the Electronics Department of the Instituto de Investigaciones Electricas (IIE) and the Centro Nacional de Investigacion y Desarrollo Tecnologico (National Center of Investigation and Technological Development (CENIDET)) named Technology Assimilation of the Power Factor Correction in the Electronic Equipment Design. In chapter 1 of this thesis the advantages of fluorescent illumination systems (IS) are mentioned, with respect to the traditional incandescent illumination systems. Also the most important characteristics of the fluorescent lamps and the operation (physical) principle will be presented, as well as the design aspects of electronic ballasts and their evolution. The proposal of the development of an experimental electronic prototype of ballast will be set forth. Chapter 2 mentions the evolution of the different schemes of fluorescent lamps ballasts, of electromagnetic, as well as electronic. Also some of the specifications that were taken into consideration for the design of the electronic prototype of the ballast presented in this thesis are mentioned. In chapter 3 the specifications of the electronic prototype of

Temporal modelling of ballast water discharge and ship-mediated invasion risk to Australia.

Science.gov (United States)

Cope, Robert C; Prowse, Thomas A A; Ross, Joshua V; Wittmann, Talia A; Cassey, Phillip

2015-04-01

Biological invasions have the potential to cause extensive ecological and economic damage. Maritime trade facilitates biological invasions by transferring species in ballast water, and on ships' hulls. With volumes of maritime trade increasing globally, efforts to prevent these biological invasions are of significant importance. Both the International Maritime Organization and the Australian government have developed policy seeking to reduce the risk of these invasions. In this study, we constructed models for the transfer of ballast water into Australian waters, based on historic ballast survey data. We used these models to hindcast ballast water discharge over all vessels that arrived in Australian waters between 1999 and 2012. We used models for propagule survival to compare the risk of ballast-mediated propagule transport between ecoregions. We found that total annual ballast discharge volume into Australia more than doubled over the study period, with the vast majority of ballast water discharge and propagule pressure associated with bulk carrier traffic. As such, the ecoregions suffering the greatest risk are those associated with the export of mining commodities. As global marine trade continues to increase, effective monitoring and biosecurity policy will remain necessary to combat the risk of future marine invasion events.

Mechanics of Ballast Compaction. Volume 3 : Field Test Results for Ballast Physical State Measurement

Science.gov (United States)

1982-03-01

The important mechanical processes which influence the ballast physical state in track are tamping, crib and shoulder compaction and train traffic. Three methods of assessing physical state were used at four railroad sites to obtain needed data on th...

Low-head air stripper treats oil tanker ballast water

International Nuclear Information System (INIS)

Goldman, M.

1992-01-01

Prototype tests conducted during the winter of 1989/90 have successfully demonstrated an economical design for air stripping volatile hydrocarbons from oily tanker ballast water. The prototype air stripper, developed for Alyeska's Ballast Water Treatment (BWT) facility in Valdez, Alaska, ran continuously for three months with an average removal of 88% of the incoming volatile organics. Initially designed to remove oil and grease compounds from tanker ballast water, the BWT system has been upgraded to a three-step process to comply with new, stringent regulations. The BWT biological oxidation process enhances the growth of bacteria present in the incoming ballast water through nutrient addition, aeration, and recirculation within a complete-mixed bioreactor. The average removal of BETX is over 95%, however, occassional upsets required the placement of a polishing air stripper downstream of the aeration tanks. Packed-tower air stripping was investigated but deemed economically unfeasible for a facility that would only occasionally be used. Twelve feet of excess gravity head in the existing BWT hydraulic gradeline were employed to drive the air stripper feed. This limited the stripper packing depth to 8 feet and imposed constraints on the design of the inlet water and air distributors. Water distribution, air flow, temperature effects, and fouling from constituents in the ballast water were investigated. The prototype was operated under water and air flow conditions similar to those specified for the full-scale unit, and at a range of test conditions above and below the normal design conditions

Numerical Investigation of a Liquid-Gas Ejector Used for Shipping Ballast Water Treatment

Directory of Open Access Journals (Sweden)

Xueguan Song

2014-01-01

Full Text Available Shipping ballast water can have significant ecological and economic impacts on aquatic ecosystems. Currently, water ejectors are widely used in marine applications for ballast water treatment owing to their high suction capability and reliability. In this communication, an improved ballast treatment system employing a liquid-gas ejector is introduced to clear the ballast water to reduce environmental risks. Commonly, the liquid-gas ejector uses ballast water as the primary fluid and chemical ozone as the secondary fluid. In this study, high-pressure water and air, instead of ballast water and ozone, are considered through extensive numerical and experimental research. The ejector is particularly studied by a steady three-dimensional multiphase computational fluid dynamics (CFD analysis with commercial software ANSYS-CFX 14.5. Different turbulence models (including standard k-ε, RNG k-ε, SST, and k-ω with different grid size and bubble size are compared extensively and the experiments are carried out to validate the numerical design and optimization. This study concludes that the RNG k-ε turbulence model is the most efficient and effective for the ballast water treatment system under consideration and simple change of nozzle shape can greatly improve the ejector performance under high back pressure conditions.

Practical Considerations Concerning the Interleaved Transition Mode Single-stage Ballast

DEFF Research Database (Denmark)

Teodorescu, Remus; Kjær, Søren Bækhøj; Munk-Nielsen, Stig

2002-01-01

The aim of this paper is to present a novel single-stage interleaved ballast focusing on practical design aspects like: key current expression, overall losses, harmonic analysis of the differential-mode EMI current and preheating ballast function. A new preheating method is also presented. A PSPICE...

Ballast water compliance monitoring: A new application for ATP

Science.gov (United States)

Lo Curto, A.; Stehouwer, P.; Gianoli, C.; Schneider, G.; Raymond, M.; Bonamin, V.

2018-03-01

The coming into force of the USCG ballast water regulations and the IMO ballast water management convention resulted in the development of several technologies approved for the treatment of ballast water. To ensure compliance of these technologies, the development of rapid and robust analysis methods was necessary. In collaboration with the SGS Group (Switzerland) and LuminUltra (Canada), Aqua-tools (France) has developed an innovative Ballast Water Treatment Monitoring (BWTM) kit for rapid onboard testing. The affordable kit provides results in less than 1 h, is easy to use and durable ensuring that the ballast water treatment system on the ship is fully compliant with the discharge standards upon arrival in port. The core of this method is a combination of high-quality reagents (lysis solution and ATP 2G Luminase™ enzyme) not inhibited by salinity and a patented fast homogenizing method for ATP extraction developed for a higher ATP recovery from zooplankton and phytoplankton. Compared to traditional analysis methods, the BWTM Kit provides fast and accurate results for all three fractions of microorganisms (≥ 50 μm, ≥ 10 ÷ < 50 μm and bacteria). Preliminary tests carried out in cooperation with SGS showed that the proposed method was able to detect onboard the efficiency of the treatment systems used. Compliance limits were established for all size fractions and a correlation between the standard methods (microscopy, plate count, MPN) and ATP was evaluated. The BWTM kit can provide a fast indication of compliance or gross exceedance. The rare borderline cases, when encountered, of course require additional confirmation.

IMPROVING THE STABILITY OF TONAL TRACK CIRCUITS UNDER FLUCTUATIONS OF BALLAST RESISTANCE

Directory of Open Access Journals (Sweden)

K. V. Honcharov

2013-11-01

Full Text Available Purpose.The purpose of investigation is the development of method for improving the stability of tonal track circuits that takes into account the actual insulation resistance (ballast resistance of rail line.Methodology. To achieve the research purpose it was proposed to automatically determine the insulation resistance of rail line, and depending on this value to adjust the output voltage of track generator. Ballast resistance is determined by the value of input resistance the rail line, which at high frequencies practically is equal to the wave impedance. To implement the proposed method it is necessary to connect to the track circuit additional high-frequency generators, high-frequency filters, unit for finding the ballast resistance and adjusting the output voltage of track generator. Findings. As a result of research it was found that at low values (less than 2 Ohms*km the change of ballast resistance causes significant change of voltage at the track receiver input, which may cause malfunction of the track circuit. Increasing the length of rail line leads to the reducing of its input resistance, raising the measuring frequency causes increasing the input resistance. In both cases, the input resistance tends to the value of the wave impedance. The measuring frequency should be chosen taking into account the length of rail line and the upper limit of ballast resistance, the value 5 Ohms*km can be taken as that limit. At higher values of ballast resistance its changes insignificantly influence the input voltage of track receiver. In this case, the adaptive adjustment of voltage at the track generator output is not performed. Originality. The method for measuring the insulation resistance of rail line has been improved that allows one to determine the ballast resistance automatically. The dependence between measuring frequency, length of rail line and ballast resistance have been determined. Practical value. The proposed method allows one to

Development of a protocol for sampling and analysis of ballast water in Jamaica

Directory of Open Access Journals (Sweden)

Achsah A Mitchell

2014-09-01

Full Text Available The transfer of ballast by the international shipping industry has negatively impacted the environment. To design such a protocol for the area, the ballast water tanks of seven bulk cargo vessels entering a Jamaican port were sampled between January 28, 2010 and August 17, 2010. Vessels originated from five ports and used three main routes, some of which conducted ballast water exchange. Twenty-six preserved and 22 live replicate zooplankton samples were obtained. Abundance and richness were higher than at temperate ports. Exchange did not alter the biotic composition but reduced the abundance. Two of the live sample replicates, containing 31.67 and 16.75 viable individuals m-3, were non-compliant with the International Convention for the Control and Management of Ships’ Ballast Water and Sediments. Approximately 12% of the species identified in the ballast water were present in the waters nearest the port in 1995 and 11% were present in the entire bay in 2005. The protocol designed from this study can be used to aid the establishment of a ballast water management system in the Caribbean or used as a foundation for the development of further protocols.

Selection and testing of ballast stones for underground railway tracks

African Journals Online (AJOL)

Ballast is broken pieces of hard rocks such as sandstones, schist, etc. approximately 25- 60 mm size, over which the railway tracks are laid. The function of the ballast is to transfer the applied load over a large surface, provide adequate elasticity, prevent creep and hold the sleepers in position. Also under wet conditions, ...

Viability assessment of invasive microplankton in ship’s treated ballast water

DEFF Research Database (Denmark)

Lundgreen, Kim; Holbech, Henrik; Pedersen, Knud Ladegaard

The spreading of aquatic invasive species in ship’s ballast water has huge environmental and health-related consequences and is causing socio-economic losses around the world in the order of US$100 billion per year. Regulations now require all large ships to have an approved ballast water treatment...... system (BWTS) on-board for cleaning of the ballast water to avoid further spreading of invasive species. To ensure BWTS compliance with discharge standards water samples need to be verified for the number of viable organisms in different size classes. The current standard method for assessing organism...

Ballast water: a review of the impact on the world public health

Directory of Open Access Journals (Sweden)

CK Takahashi

2008-01-01

Full Text Available Since the nineteenth century ships have been using ballast water (BW for safety, stability, propulsion and maneuverability, as well as to redress loss of fuel weight and water consumption, and to maintain structural stress at acceptable levels. Ballast water has been spreading many non-native species around the globe, but little is known about the extent and potential significance of ship-mediated transfer of microorganisms. The global movements of ballast water by ships create a long-distance dispersal mechanism for human pathogens that may be important in the worldwide distribution of microorganisms, as well as for the epidemiology of waterborne diseases. Only a few studies have been carried out on this subject, most of them involving ballast water containing crustacean larvae and phytoplankton. Specialized microbiological studies on these waters are necessary to avoid a repeat of what happened in 1991, when epidemic cholera was reported in Peru and rapidly spread through Latin America and Mexico. In July of 1992, Vibrio cholerae was found in the USA and the Food and Drug Administration (FDA determined that it came from ballast water of ships whose last port of call was in South America. In Brazil, just a few studies about the subject have been performed. An exploratory study by the Brazilian National Health Surveillance Agency (Agência Nacional de Vigilância Sanitária - ANVISA found in ballast water different microorganisms, such as fecal coliforms, Escherichia coli, Enterococcus faecalis, Clostridium perfringens, coliphages, Vibrio cholerae O1 and Vibrio cholerae non-O1. Until now, Brazil has been focusing only on organisms transported to its territory from other countries by ballast water, to avoid their establishment and dissemination in Brazilian areas. Studies that can assess the probability that water ballast carries pathogenic microorganisms are extremely important, as is the examination of ships that arrive in the country

A unique aspect of ballast water management requirements – The same location concept

International Nuclear Information System (INIS)

Gollasch, Stephan; David, Matej

2012-01-01

Under certain circumstances vessels do not need to meet ballast water management requirements as stated in the International Convention for the Management and Control of Ballast Water and Sediments (BWM Convention). Besides exceptions to ensure e.g., (a) the safety of a ship, (b) discharge of ballast water for the purpose of avoiding or minimizing pollution incidents, (c) uptake and discharge on high seas of the same ballast water, the same location concept comes into play as ballast water discharges from a ship at the same location where it was taken up is also excepted from BWM requirements. The term same location was not defined in this instrument, hence it is exposed to different interpretations (e.g., a terminal, a port, a larger area where two or more ports may be located). As the BWM Convention is an instrument with biological meaning, the authors recommend a biologically meaningful definition of the same location in this contribution.

33 CFR 151.2035 - What are the required ballast water management practices for my vessel?

Science.gov (United States)

2010-07-01

... water management practices for my vessel? 151.2035 Section 151.2035 Navigation and Navigable Waters...) must employ at least one of the following ballast water management practices: (1) Perform complete... SUBSTANCES, GARBAGE, MUNICIPAL OR COMMERCIAL WASTE, AND BALLAST WATER Ballast Water Management for Control of...

Modelo dinámico para lámparas de descarga de alta intensidad en alta frecuencia; Dynamic model for high intensity discharge lamps in high frequency

Directory of Open Access Journals (Sweden)

Leonardo Cedeño Rodríguez

2015-04-01

Full Text Available En este trabajo se desarrolla el modelado dinámico de lámparas de descarga de alta intensidad (HID en inglés, de manera que pueda contribuir al desarrollo posterior de un sistema de control avanzado sobre la etapa de potencia de un balasto electrónico, que permita operar este tipo de lámparas en alta frecuencia. El modelo tiene en cuenta la presencia del fenómeno de la resonancia acústica (RA, que usualmente se presenta en las lámparas HID a frecuencias elevadas. Para el modelado se emplean técnicas híbridas, teniendo como punto de partida las ecuaciones de balance de energía en el interior de la lámpara, en tanto para la parametrización, se aplica identificación de sistemas y optimización mediante algoritmos genéticos. La implementación del modelo se realiza con el software Matlab R2011a. Como resultado se obtiene un modelo dinámico para lámparas HID en alta frecuencia, validado para lámparas de alta presión de sodio.In this paper the dynamic modeling of high intensity discharge lamps (HID is developed. This will contribute to the further development of an advanced control system on the power stage of an electronic ballast, which allows these lamps operate at high frequency. The model must take into account the presence of the acoustic resonance’s phenomenon (AR, which usually occurs when HID lamps operates at high frequency. Hybrid modeling techniques were employed, the balance equations and the empirical expressions were obtained and the model was parameterized by identification techniques and optimization based on genetic algorithms. The implementation of the model has performed using Simulink tool of Matlab R2011a software. As a result, a dynamic model for HID lamps in high frequency has achieved and validated for high-pressure sodium lamps (HPS.

Pollution characteristics and ecological risk of heavy metals in ballast tank sediment.

Science.gov (United States)

Feng, Daolun; Chen, Xiaofei; Tian, Wen; Qian, Qun; Shen, Hao; Liao, Dexiang; Lv, Baoyi

2017-02-01

This study was conducted to illustrate the contents and potential ecological risk of heavy metals in ballast tank sediment. Ballast sediment samples were collected from six ships during their stay in shipyard, and the heavy metals were determined by inductive coupled plasma emission spectrometer. Results showed that high concentrations of heavy metals were detected in all six sediment samples following the order: Zn > Cu > Pb > Cr > As > Cd > Hg. The geoaccumulation index explained the average pollution degree of heavy metals decreased as the following: Zn > Pb > Cu > As > Cr > Hg, and the environmental risk indices suggested that concentration found of Zn, Pb, and Cu might be highly toxic to aquatic organisms. Principal component and correlation analysis indicated the metal pollution in ballast tank sediment was affected by complex and different contamination mechanisms, and the corrosion of ballast tank played an important role in this process. In conclusion, this study is very useful for comprehensive consideration and efficient management of ballast tank sediment in order to protect the marine environment.

Verification of mid-ocean ballast water exchange using naturally occurring coastal tracers

Energy Technology Data Exchange (ETDEWEB)

Murphy, Kathleen; Boehme, Jennifer; Coble, Paula; Cullen, Jay; Field, Paul; Moore, Willard; Perry, Elgin; Sherrell, Robert; Ruiz, Gregory

2004-04-01

We examined methods for verifying whether or not ships have performed mid-ocean ballast water exchange (BWE) on four commercial vessels operating in the Pacific and Atlantic Oceans. During BWE, a ship replaces the coastal water in its ballast tanks with water drawn from the open ocean, which is considered to harbor fewer organisms capable of establishing in coastal environments. We measured concentrations of several naturally occurring chemical tracers (salinity, six trace elements, colored dissolved organic matter fluorescence and radium isotopes) along ocean transects and in ballast tanks subjected to varying degrees of BWE (0-99%). Many coastal tracers showed significant concentration changes due to BWE, and our ability to detect differences between exchanged and unexchanged ballast tanks was greatest under multivariate analysis. An expanded dataset, which includes additional geographic regions, is now needed to test the generality of our results.

Verification of mid-ocean ballast water exchange using naturally occurring coastal tracers

International Nuclear Information System (INIS)

Murphy, Kathleen; Boehme, Jennifer; Coble, Paula; Cullen, Jay; Field, Paul; Moore, Willard; Perry, Elgin; Sherrell, Robert; Ruiz, Gregory

2004-01-01

We examined methods for verifying whether or not ships have performed mid-ocean ballast water exchange (BWE) on four commercial vessels operating in the Pacific and Atlantic Oceans. During BWE, a ship replaces the coastal water in its ballast tanks with water drawn from the open ocean, which is considered to harbor fewer organisms capable of establishing in coastal environments. We measured concentrations of several naturally occurring chemical tracers (salinity, six trace elements, colored dissolved organic matter fluorescence and radium isotopes) along ocean transects and in ballast tanks subjected to varying degrees of BWE (0-99%). Many coastal tracers showed significant concentration changes due to BWE, and our ability to detect differences between exchanged and unexchanged ballast tanks was greatest under multivariate analysis. An expanded dataset, which includes additional geographic regions, is now needed to test the generality of our results

Backfilling with mixtures of bentonite/ballast materials or natural smectitic clay?

International Nuclear Information System (INIS)

Pusch, R.

1998-10-01

Comparison of the performance of backfills of mixed MX-80 and crushed rock ballast, and a natural smectitic clay, represented by the German Friedland clay, shows that the latter performs better than mixtures with up to 30 % MX-80. Considering cost, Friedland clay prepared to yield air-dry powder grains is cheaper than mixtures of 30 % MX-80 and crushed ballast. Both technically and economically it appears that the Friedland clay is a competitive alternative to mixtures of 30 % MX-80 and crushed ballast. However, it remains to be demonstrated on a full scale that Friedland clay ground to a suitable grain size distribution can be acceptably compacted on site

A shipboard comparison of analytic methods for ballast water compliance monitoring

Science.gov (United States)

Bradie, Johanna; Broeg, Katja; Gianoli, Claudio; He, Jianjun; Heitmüller, Susanne; Curto, Alberto Lo; Nakata, Akiko; Rolke, Manfred; Schillak, Lothar; Stehouwer, Peter; Vanden Byllaardt, Julie; Veldhuis, Marcel; Welschmeyer, Nick; Younan, Lawrence; Zaake, André; Bailey, Sarah

2018-03-01

Promising approaches for indicative analysis of ballast water samples have been developed that require study in the field to examine their utility for determining compliance with the International Convention for the Control and Management of Ships' Ballast Water and Sediments. To address this gap, a voyage was undertaken on board the RV Meteor, sailing the North Atlantic Ocean from Mindelo (Cape Verde) to Hamburg (Germany) during June 4-15, 2015. Trials were conducted on local sea water taken up by the ship's ballast system at multiple locations along the trip, including open ocean, North Sea, and coastal water, to evaluate a number of analytic methods that measure the numeric concentration or biomass of viable organisms according to two size categories (≥ 50 μm in minimum dimension: 7 techniques, ≥ 10 μm and scientific approaches (e.g. flow cytometry). Several promising indicative methods were identified that showed high correlation with microscopy, but allow much quicker processing and require less expert knowledge. This study is the first to concurrently use a large number of analytic tools to examine a variety of ballast water samples on board an operational ship in the field. Results are useful to identify the merits of each method and can serve as a basis for further improvement and development of tools and methodologies for ballast water compliance monitoring.

Low-watt lamps seen bad in many retrofits: said to burn out pre-1978 standard ballasts

Energy Technology Data Exchange (ETDEWEB)

Cohn, L.

1982-06-21

The standard ballasts used in early energy-efficient fluorescent lamps are vulnerable to premature burnout. Retrofitting expensive new ballasts will eliminate any savings from the lamps. GTE/Sylvania, Norelco, and Westinghouse acknowledged the problem, while General Electric had no comment. Ballasts made in the last four years have been made compatible with energy-efficient lamps. The vendors claim it is the ballast manufacturers' responsibility to inform users that their product risks early burnout. (DCK)

Technical Analysis Ballast Water Treatment By Using Economizer Utilizing Main Engines Exhaust Heat To Comply With International Ship Ballast Water Management At Mv. Leader Win

Directory of Open Access Journals (Sweden)

Hari Prastowo

2017-03-01

Full Text Available Based on the International Ballast Water Management regulations (IBWM, waste water ballast itself has the attention of some researchers to reduce the amount of waste species present in the ballast water with a variety of methods, as of biological, physical, mechanical, and chemical. The decision-making tools such as ballast water heater, flow-through system and others where possible these tools can minimize waste species in ballast water at a certain temperature or pressure of the flow according to the calculations. This study was aimed to calculate and analysis the effectiveness of the system treatment between Option 1 (Economizer & Bundle and Option 2 (Economizer & Heat Excharger then it will compare. First option is using economizer and bundles to transfer a heat from a source heat of exhaust gas then medium by thermal oil circulated. The second option is using economizer and heat excharger where a same heat source , but sea water from ballast tank sirculated to heat excharger. And from economizer to heat excharger is using thermal oil as a heat medium. For all calculation and anaalysis is using softwere HTRI. First option having a duty 2.503 MegaWatts at economizer and 1.9567 MegaWatts at bundles. Over design 2.01% at Economizer and 7.1%5 at bundles. Pessure drop 63.287 kPa at thermal oil after economizer and 68.196 kPa after bundles. Treatment time to this option is 44.424 hors. Second option having a duty 3.38 MegaWatts at economizer and 3.1227 MegaWatts at heat excharger. Over design 5.85% at Economizer and 3.49%5 at heat excharger. Pessure drop 38.697 kPa at thermal oil after economizer and 28.476 kPa after heat excharger. Treatment time to second option is 42.03 hours. Option 2 (Economizer & Heat Excharger is more optimum than option in analytical techniques. By analysis of treatment system, are expected this thesis can be applied to either the MV. Leader Win Vessel to comply with the operational needs according to standard

Backfilling with mixtures of bentonite/ballast materials or natural smectitic clay?

Energy Technology Data Exchange (ETDEWEB)

Pusch, R. [Geodevelopment AB, (Sweden)

1998-10-01

Comparison of the performance of backfills of mixed MX-80 and crushed rock ballast, and a natural smectitic clay, represented by the German Friedland clay, shows that the latter performs better than mixtures with up to 30 % MX-80. Considering cost, Friedland clay prepared to yield air-dry powder grains is cheaper than mixtures of 30 % MX-80 and crushed ballast. Both technically and economically it appears that the Friedland clay is a competitive alternative to mixtures of 30 % MX-80 and crushed ballast. However, it remains to be demonstrated on a full scale that Friedland clay ground to a suitable grain size distribution can be acceptably compacted on site 14 refs, 32 figs, 6 tabs

How to approach ballast water management in European seas

Science.gov (United States)

David, Matej; Gollasch, Stephan

2018-02-01

The latest research continues to show that the ballast water issue is very complex, which makes it very challenging to manage. In 2004, the International Convention for the Control and Management of Ships' Ballast Water and Sediments (BWM Convention) was adopted to globally harmonize action against the transfer of harmful aquatic organisms and pathogens via ships' ballast water and related sediments. Analyses of the BWM Convention requirements, conducted through different research projects mainly aiming to provide support for the implementation of the BWM Convention, have shown that there are different steps countries need to take and that there are still some open issues which need to be solved. This paper presents some of the main issues identified and the core theoretical and applied measures required to solve these issues, with the aim to support more efficient and coordinated implementation of the BWM Convention requirements in EU seas. The approaches recommended here for the EU may be universally interesting for similar application in other areas of the world.

Study on the Elasticity-Plasticity-Stickiness of the Railway Crushed Stone Ballast

Institute of Scientific and Technical Information of China (English)

Gao Liang

2004-01-01

This paper is mainly aimed at the mechanics characteristic elas of ticity-plasticitystickiness existed in the CWR (continuously welded rails) track plane of the railway crushed stone ballast. As an important mechanics parameter of the CWR track plane, the ballast resistance is mainly influenced by this mechanics characteristic. Through the systematic experimental research and the theoretical analysis, this mechanics characteristic of the ballast resistance is revealed and a reasonable theoretical model is built for it. This study set a sound foundation for further studying the CWR track deformation property. It will be beneficial to the development of high-speed railway in China.

Assessing the viability of microorganisms in the ballast water of vessels transiting the North Atlantic Ocean.

Science.gov (United States)

Steichen, Jamie L; Quigg, Antonietta

2015-12-15

Testing phytoplankton viability within ballast tanks and receiving waters of ballast water discharge remain understudied. Potentially harmful dinoflagellates and diatoms are transported via ballast water to Galveston Bay, Texas (USA), home to three major ports: Houston, Texas City and Galveston. Ballast water from vessels transiting the North Atlantic Ocean was inoculated into treatments representing low and high salinity conditions similar to the Ports of Houston and Galveston respectively. Phytoplankton in ballast water growout experiments were deemed viable and showed growth in low and mid salinities with nutrient enrichment. Molecular methods identified several genera: Dinophysis, Gymnodinium, Gyrodinium, Heterocapsa, Peridinium, Scrippsiella, Chaetoceros and Nitzschia. These phytoplankton genera were previously identified in Galveston Bay except Scrippsiella. Phytoplankton, including those capable of forming harmful algal blooms leading to fish and shellfish kills, are transported to Galveston Bay via ballast water, and are viable when introduced to similar salinity conditions found in Galveston Bay ports. Copyright © 2015 Elsevier Ltd. All rights reserved.

Laser cutting of concretes with various ballasts

International Nuclear Information System (INIS)

Hamasaki, Masanobu; Katsumura, Munehide; Utsumi, Hiroaki

1985-01-01

The biological shield concrete and the radiation shield concrete which construct a part of the atomic reactor must be demolished with the decommissioning of the atomic reactor plants. In a case, the demolition using a laser is expected as one of excellent method for the decommissioning of these radioactive concretes. The fundamental cuttings of a mortar, the concretes with andesite, lime stone and gray wacke as ballast and a concrete reinforced with mild steel rods were therefore carried out using a 5 kW output CO 2 laser. As the results of experiment, it was cleared that cutting results varied with ballasts, 100 mm thick reinforced concrete could be cut, safety was high because few dross and few fume were produced. (author)

Difficulties in obtaining representative samples for compliance with the Ballast Water Management Convention

Digital Repository Service at National Institute of Oceanography (India)

Carney, K.J; Basurko, O.C; Pazouki, K.; Marsham, S.; Delany, J; Desai, D.V.; Anil, A.C; Mesbahi, E.

water, the shape, size and number of ballast tanks and the heterogeneous distribution of organisms within tanks. These factors hinder efforts to obtain samples that truly represent the total ballast water onboard a vessel. A known cell density...

Review of interdisciplinary devices for detecting the quality of ship ballast water.

Science.gov (United States)

Bakalar, Goran

2014-01-01

The results of the ship ballast water treatment systems neutralization need to be verified in a transparent and trustful way before the ship enters a port. Some researches and results, explained in this article, confirm a need for a good verification. If there is no good methodology agreed, then it would not be accepted the solution that the BWMC (Ballast Water Management Convention) 2004 did protect the sea environment in full meaning. The main problem of ballast neutralization are remaining microorganisms (algae blooms, bacteria) ≥10 and PROMETHEE II (Preference Ranking Organization Method for Enrichment Evaluations) and results were shown by D-Sight software projections.

10 CFR 431.322 - Definitions concerning metal halide lamp ballasts and fixtures.

Science.gov (United States)

2010-01-01

... high intensity discharge fixture, the efficiency of a lamp and ballast combination, expressed as a... lamps. Metal halide lamp means a high intensity discharge lamp in which the major portion of the light... 10 Energy 3 2010-01-01 2010-01-01 false Definitions concerning metal halide lamp ballasts and...

A comparison of six different ballast water treatment systems based on UV radiation, electrochlorination and chlorine dioxide

NARCIS (Netherlands)

Stehouwer, P.P.; Buma, A.; Peperzak, L.

2015-01-01

The spread of aquatic invasive species through ballast water is a major ecological and economical threat. Because of this, the International Maritime Organization (IMO) set limits to the concentrations of organisms allowed in ballast water. To meet these limits, ballast water treatment systems

75 FR 14287 - Energy Conservation Program: Test Procedures for Fluorescent Lamp Ballasts

Science.gov (United States)

2010-03-24

... uses the same measurement techniques as the existing test procedure. In any rulemaking to amend a test...; and (3) appearing on page 29 of the transcript. \\6\\ Ballast type refers to a grouping of ballasts that... grouping of lamps that have the same length, lumen package, base type, and diameter. In the ongoing...

Asbestos quantification in track ballast, a complex analytical problem

Science.gov (United States)

Cavallo, Alessandro

2016-04-01

Track ballast forms the trackbeb upon which railroad ties are laid. It is used to bear the load from the railroad ties, to facilitate water drainage, and also to keep down vegetation. It is typically made of angular crushed stone, with a grain size between 30 and 60 mm, with good mechanical properties (high compressive strength, freeze - thaw resistance, resistance to fragmentation). The most common rock types are represented by basalts, porphyries, orthogneisses, some carbonatic rocks and "green stones" (serpentinites, prasinites, amphibolites, metagabbros). Especially "green stones" may contain traces, and sometimes appreciable amounts of asbestiform minerals (chrysotile and/or fibrous amphiboles, generally tremolite - actinolite). In Italy, the chrysotile asbestos mine in Balangero (Turin) produced over 5 Mt railroad ballast (crushed serpentinites), which was used for the railways in northern and central Italy, from 1930 up to 1990. In addition to Balangero, several other serpentinite and prasinite quarries (e.g. Emilia Romagna) provided the railways ballast up to the year 2000. The legal threshold for asbestos content in track ballast is established in 1000 ppm: if the value is below this threshold, the material can be reused, otherwise it must be disposed of as hazardous waste, with very high costs. The quantitative asbestos determination in rocks is a very complex analytical issue: although techniques like TEM-SAED and micro-Raman are very effective in the identification of asbestos minerals, a quantitative determination on bulk materials is almost impossible or really expensive and time consuming. Another problem is represented by the discrimination of asbestiform minerals (e.g. chrysotile, asbestiform amphiboles) from the common acicular - pseudo-fibrous varieties (lamellar serpentine minerals, prismatic/acicular amphiboles). In this work, more than 200 samples from the main Italian rail yards were characterized by a combined use of XRD and a special SEM

Comparison of mass and energy balances for air blown and thermally ballasted fluidized bed gasifiers

International Nuclear Information System (INIS)

Lysenko, Steve; Sadaka, Samy; Brown, Robert C.

2012-01-01

The objective of this study was to compare the mass and energy balances for a conventional air blown fluidized bed gasifier and a ballasted fluidized bed gasifier developed at Iowa State University. The ballasted gasifier is an indirectly heated gasifier that uses a single reactor for both combustion and pyrolysis. Heat accumulated in high-temperature phase change material during the combustion phase is released during the pyrolysis phase to generate producer gas. Gas composition, tar and char contents, cold gas efficiency, carbon conversion, and hydrogen yield per unit biomass input were determined as part of these evaluation. During the pyrolysis phase of ballasted gasification, higher volumetric concentrations of hydrogen and methane were obtained than during air blown gasification. Hydrogen yield for ballasted gasification was 14 g kg −1 of biomass, which was about 20% higher than that obtained during air blown gasification. The higher heating value of the producer gas also reached higher levels during the ballasted pyrolysis phase than that of air blown gasification. Heating value for air blown gasification was 5.2 MJ m −3 whereas the heating value for the ballasted pyrolysis phase averaged 5.5 MJ m −3 , reaching a maximum of 8.0 MJ m −3 . The ballasted gasifier was expected to yield producer gas with average heating value as high as 15 MJ m −3 but excessive use of nitrogen to purge and cool the fuel feeder system greatly diluted the producer gas. Relatively simple redesign of the feeder system would greatly reduce the use of purge gas and may increase the heating values to about 17.5 MJ m −3 . Higher char production per kilogram of biomass was associated with the ballasted system, producing 140 g kg −1 of biomass compared to only 53 g kg −1 of biomass during air blown gasification. On the other hand, tar concentrations in the producer gas were 6.0 g m −3 for ballasted gasification compared to 11.7 g m −3 for air blown gasification. On

Effect of a ballast zone on the hydraulic stability of a single-pass steam generator

International Nuclear Information System (INIS)

Belyakov, I.I.; Kvetnyj, M.A.; Loginov, D.A.

1985-01-01

A new mechanism of hydraulic instability of boiling channels with convection heating which reveals in the presence of a developed ballast zone at decreased loads of a counterflan steam generator operation is considered. It is shown that for the certain combinations of thermal and technical parameters pulsation regimes caused by the ballast zone displacement over the heating surface are possible. The parameter relation at which the ballast zone position becomes unstable is obtained. The effect of the ballast zone on the statis steam generator stability is established. A mechanism of whole-circuit pulsations revealed when developing start regimes of single-pass steam generator heated with liquid sodium is explained from the positions of the instability

Modeling Ballasted Tracks for Runoff Coefficient C

Science.gov (United States)

2012-08-01

In this study, the Regional Transportation District (RTD)s light rail tracks were modeled to determine the Rational Method : runoff coefficient, C, values corresponding to ballasted tracks. To accomplish this, a laboratory study utilizing a : rain...

Strategies for the correction of the power factor in electronic ballasts with low crest factor; Estrategias para la correccion del factor de potencia en balastros electronicos con bajo factor de cresta

Energy Technology Data Exchange (ETDEWEB)

Martinez Mata, Arturo Javier

2002-07-15

The goal in this work is to develop electronic ballast for fluorescent lamps with high power factor with the smaller number of components. With this aim it is looked for 1) to study the impact of the value of the filtrating capacitor used in a conventional rectifier on the harmonic content of the line current and the crest factor in the lamp, 2) to study resonant tanks commonly used in electronic ballasts with the purpose of observing the feasibility of implementing a control in frequency to vary the gain of the resonant tank and 3) to propose a strategy of frequency modulation that allows to reach low harmonic distortion of the line current maintaining a low crest factor. In chapter one the used theoretical concepts in illumination systems are presented, the justification for the use of electronic ballasts in fluorescent lamps, a revision of the state-of-the-art in the correction of the power factor in electronic ballasts and two strategies for the correction of this factor. In the next chapter the conventional resonant topologies used in the literature are presented, together with the analysis of resonant structures with high gain in steady state to compensate the variations of the instantaneous voltage of the DC bus that feeds the resonant inverter. Also simulations in PSpice are included to know the behavior of each one of the resonant structures and to be able to select, in that way, the most adequate resonant topology for this work. In the third chapter the strategy is presented for the correction of the power factor, eliminating the filtering capacitor. The effects of this elimination as far as the line current and the lamp current are shown. The characterization of the resonant tank in open loop and closed loop is presented. The method is described to control the gain of the resonant investor and its implementation. Experimental results obtained when reducing the filtering capacitor are included and the implementation of the proposed control loop to reduce

Modeling the distribution of colonial species to improve estimation of plankton concentration in ballast water

Science.gov (United States)

Rajakaruna, Harshana; VandenByllaardt, Julie; Kydd, Jocelyn; Bailey, Sarah

2018-03-01

The International Maritime Organization (IMO) has set limits on allowable plankton concentrations in ballast water discharge to minimize aquatic invasions globally. Previous guidance on ballast water sampling and compliance decision thresholds was based on the assumption that probability distributions of plankton are Poisson when spatially homogenous, or negative binomial when heterogeneous. We propose a hierarchical probability model, which incorporates distributions at the level of particles (i.e., discrete individuals plus colonies per unit volume) and also within particles (i.e., individuals per particle) to estimate the average plankton concentration in ballast water. We examined the performance of the models using data for plankton in the size class ≥ 10 μm and test ballast water compliance using the above models.

Microprocessor control unit of thyristor regulator of microhydroelectric power station ballast load

International Nuclear Information System (INIS)

Nomokonova, Yu; Bogdanov, E

2014-01-01

The operational principle of microhydroelectric power station ballast load is presented. The comparative overview of the mathematical modeling methods is performed. The ranges of thyristors optimal work are shown as a result of the regulator regimes analysis. Shows the necessity of regulation the ballast load in microhydroelectric power station with help of developed algorithm of the program for microprocessor control

Ecosystem under pressure: ballast water discharge into Galveston Bay, Texas (USA) from 2005 to 2010.

Science.gov (United States)

Steichen, Jamie L; Windham, Rachel; Brinkmeyer, Robin; Quigg, Antonietta

2012-04-01

Ballast water exchange processes facilitate the dispersal and unnatural geographic expansion of phytoplankton, including harmful algal bloom species. From 2005 to 2010, over 45,000 vessels (≈ 8000 annually) travelled across Galveston Bay (Texas, USA) to the deep-water ports of Houston (10th largest in the world), Texas City and Galveston. These vessels (primarily tankers and bulkers) discharged ≈ 1.2 × 10(8) metrictons of ballast water; equivalent to ≈ 3.4% of the total volume of the Bay. Over half of the ballast water discharged had a coastwise origin, 96% being from US waters. Galveston Bay has fewer non-indigenous species but receives a higher volume of ballast water discharge, relative to the highly invaded Chesapeake and San Francisco Bays. Given the magnitude of shipping traffic, the role of Galveston Bay, both as a recipient and donor region of non-indigenous phytoplankton species is discussed here in terms of the invasibility risk to this system by way of ballast water. Copyright © 2012 Elsevier Ltd. All rights reserved.

Atomization in a graphite furnace with ballast - a method of improvement of reliability of atomic absorption analysis

International Nuclear Information System (INIS)

Katskov, D.A.; Grinshtejn, I.L.

1978-01-01

For the purpose of improving the reliability with which elements are determined in atomic absorption analysis with atomization in a graphite furnace, a method is proposed based on the use of a furnace with an extra ballast body. A small cylinder of graphite or refractory metal (Ta) placed in the central part of the furnace, is used as ballast. When in poor heat contact with the wall the ballast is heated by ray emission at a somewhat slower rate than the furnace. It is shown that the kinetics of evaporation of the substance being analysed in the ballast furnace is determined by the rate of change of temperature of the ballast body. As a result of the lag in evaporation, vapour from the analysed substance reaches a zone of a much higher temperature than with evaporation in the usual type furnace, leading to an increase in the degree of atomization. Theoretical analysis establishes the temperature of the ballast, and conditions for the determination of elements (Cd) are optimized. The experiments conducted indicate a considerable decrease in the effect of the composition of the sample on the results of the analysis and a lower molecular interference in the ballast furnace. With high evaporation lag the vapours of the sample reach the zone of practically constant temperature, thus making it possible to use the integral method of absorption registration with absolute accuracy. With fractionated distillation of volatile components of the sample, fractionation is considerably more accurate in a ballast furnace than in the usual type furnace

Effects of various ballast water treatment methods on the survival of phytoplankton and bacteria

NARCIS (Netherlands)

Stehouwer, P.P.

2016-01-01

Aquatic invasive species are among the worst threats to marine biodiversity. The main vector for the spread of these aquatic invasive species is ships’ ballast water. Because of this, the International Maritime Organization (IMO) adopted the Ballast Water Convention. Part of this convention is the

Survey on germination and species composition of dinoflagellates from ballast tanks and recent sediments in ports on the South Coast of Finland, North-Eastern Baltic Sea

International Nuclear Information System (INIS)

Pertola, Sari . E-mail sari.pertola@fimr.fi; Faust, Maria A.; Kuosa, Harri

2006-01-01

Cyst beds in ships and ports in Finland have previously been unstudied. Therefore, sediments from ships' ballast water tanks and four Finnish ports were sampled for dinoflagellate cysts and other phytoplankton. Untreated sediments were incubated at 10 o C and 20 o C in the local 6 psu salinity for 1, 4 and 7 days, and vegetative cells were examined with light and scanning electron microscope. Sediments were inhabited by various dinoflagellates, diatoms, chlorophytes, cyanophytes and small flagellates. Germinated dinoflagellates were found in 90% of ballast tanks and in all ports. Gymnodiniales spp. and Heterocapsa rotundata formed a major proportion of the proliferating dinoflagellate cells. One species, Peridinium quinquecorne, not previously reported from the Baltic Sea, was identified with SEM. The study emphasises that ships are potential transport vehicles for dinoflagellate cysts even in the low salinity Finnish waters, and small-sized dinoflagellates should be focused upon in ballast water studies

Possible Ballast Water Transfer of Lionfish to the Eastern Pacific Ocean.

Science.gov (United States)

MacIsaac, Hugh J; De Roy, Emma M; Leung, Brian; Grgicak-Mannion, Alice; Ruiz, Gregory M

2016-01-01

The Indo-Pacific Red Lionfish was first reported off the Florida coast in 1985, following which it has spread across much of the SE USA, Gulf of Mexico, and Caribbean Sea. Lionfish negatively impact fish and invertebrate assemblages and abundances, thus further spread is cause for concern. To date, the fish has not been reported on the Pacific coast of North or Central America. Here we examine the possibility of ballast water transfer of lionfish from colonized areas in the Atlantic Ocean to USA ports on the Pacific coast. Over an eight-year period, we documented 27 commercial vessel-trips in which ballast water was loaded in colonized sites and later discharged untreated into Pacific coast ports in the USA. California had the highest number of discharges including San Francisco Bay and Los Angeles-Long Beach. A species distribution model suggests that the probability of lionfish establishment is low for the western USA, Colombia and Panama, low to medium for Costa Rica, Nicaragua, El Salvador and Guatemala, medium to high for mainland Ecuador, and very high for western Mexico, Peru and the Galapagos Islands. Given the species' intolerance of freshwater conditions, we propose that ballast water exchange be conducted in Gatún Lake, Panama for western-bound vessels carrying 'risky' ballast water to prevent invasion of the eastern Pacific Ocean.

Possible Ballast Water Transfer of Lionfish to the Eastern Pacific Ocean.

Directory of Open Access Journals (Sweden)

Hugh J MacIsaac

Full Text Available The Indo-Pacific Red Lionfish was first reported off the Florida coast in 1985, following which it has spread across much of the SE USA, Gulf of Mexico, and Caribbean Sea. Lionfish negatively impact fish and invertebrate assemblages and abundances, thus further spread is cause for concern. To date, the fish has not been reported on the Pacific coast of North or Central America. Here we examine the possibility of ballast water transfer of lionfish from colonized areas in the Atlantic Ocean to USA ports on the Pacific coast. Over an eight-year period, we documented 27 commercial vessel-trips in which ballast water was loaded in colonized sites and later discharged untreated into Pacific coast ports in the USA. California had the highest number of discharges including San Francisco Bay and Los Angeles-Long Beach. A species distribution model suggests that the probability of lionfish establishment is low for the western USA, Colombia and Panama, low to medium for Costa Rica, Nicaragua, El Salvador and Guatemala, medium to high for mainland Ecuador, and very high for western Mexico, Peru and the Galapagos Islands. Given the species' intolerance of freshwater conditions, we propose that ballast water exchange be conducted in Gatún Lake, Panama for western-bound vessels carrying 'risky' ballast water to prevent invasion of the eastern Pacific Ocean.

International dissemination of epidemic Vibrio cholerae by cargo ship ballast and other nonpotable waters.

Science.gov (United States)

McCarthy, S A; Khambaty, F M

1994-07-01

In 1991 and 1992, toxigenic Vibrio cholerae O1, serotype Inaba, biotype El Tor, was recovered from nonpotable (ballast, bilge, and sewage) water from five cargo ships docked in ports of the U.S. Gulf of Mexico. Four of these ships had taken on ballast water in cholera-infected countries; the fifth took on ballast in a noninfected country. Isolates examined by pulsed-field gel electrophoresis were indistinguishable from the Latin American epidemic strain, C6707; however, they differed significantly from the endemic Gulf Coast strain (VRL 1984), the sixth-pandemic strain (569-B), and a V. cholerae non-O1 strain isolated from a ship arriving from a foreign port. On the basis of our findings, the Food and Drug Administration recommended that the U.S. Coast Guard issue an advisory to shipping agents and captains requesting that ballast waters be exchanged on the high seas before entry of ships into U.S. ports.

Importance of the harmonics in the lighting systems for the electric energy saving; Importancia de las armonicas en el sistema de iluminacion para el ahorro de energia electrica

Energy Technology Data Exchange (ETDEWEB)

Garibay Mendoza, V. [Lumisistemas, departamento de aseguramineto de calidad, Naucalpan (Mexico); Hernandez Bernal, J. M. [UNICORP, Mexico, D. F. (Mexico)

1995-12-31

In a lighting system the discharge lamps (fluorescent and high intensity discharge (HID)), ballast and controls are generating elements of harmonics. As a consequence of the tendency of saving energy, the use of electronic ballasts and controls that integrate dimmers, daylight and present sensors has increased in order to optimize the energy use. This paper presents the harmonics generation resulting from the fluorescent lamps operating different electronic ballasts as well as their electronic controls. Likewise, are also shown the effects caused by generation of harmonics components by the lighting system in the electric system that go from the voltage and current distortion, the presence of currents in the neutral conductor in balanced systems to the repercussions in the metering equipment such as watthour meters and the effects the lighting equipment suffer due to the presence of harmonics, such as the power factor decrease in ballasts that are of high power factor and the temperature increment in the magnetic type ballasts. [Espanol] Dentro de un sistema de iluminacion, las lamparas de descarga (fluorescentes y alta intensidad de descarga {sup H}ID{sup )}, balastros y los controles son elementos generadores de armonicas. A consecuencia de la tendencia al ahorro de energia se ha incrementado el uso de balastros electronicos y controles que integran atenuadores de luz (dimmers), sensores de luz natural y de presencia con el fin de optimizar el uso de la energia. Este trabajo presenta los resultados de generacion de armonicas para lamparas fluorescentes, operando diferentes balastros electronicos asi como con controles electronicos. Asi mismo son presentados los efectos causados por la generacion de componentes armonicas por el sistema de iluminacion dentro del sistema electrico que van desde la distorsion en voltaje y corriente, la presencia de corrientes dentro del conductor neutro en sistemas balanceados, asi como la repercusion en los equipos de medicion tales

Importance of the harmonics in the lighting systems for the electric energy saving; Importancia de las armonicas en el sistema de iluminacion para el ahorro de energia electrica

Energy Technology Data Exchange (ETDEWEB)

Garibay Mendoza, V [Lumisistemas, departamento de aseguramineto de calidad, Naucalpan (Mexico); Hernandez Bernal, J M [UNICORP, Mexico, D. F. (Mexico)

1996-12-31

In a lighting system the discharge lamps (fluorescent and high intensity discharge (HID)), ballast and controls are generating elements of harmonics. As a consequence of the tendency of saving energy, the use of electronic ballasts and controls that integrate dimmers, daylight and present sensors has increased in order to optimize the energy use. This paper presents the harmonics generation resulting from the fluorescent lamps operating different electronic ballasts as well as their electronic controls. Likewise, are also shown the effects caused by generation of harmonics components by the lighting system in the electric system that go from the voltage and current distortion, the presence of currents in the neutral conductor in balanced systems to the repercussions in the metering equipment such as watthour meters and the effects the lighting equipment suffer due to the presence of harmonics, such as the power factor decrease in ballasts that are of high power factor and the temperature increment in the magnetic type ballasts. [Espanol] Dentro de un sistema de iluminacion, las lamparas de descarga (fluorescentes y alta intensidad de descarga {sup H}ID{sup )}, balastros y los controles son elementos generadores de armonicas. A consecuencia de la tendencia al ahorro de energia se ha incrementado el uso de balastros electronicos y controles que integran atenuadores de luz (dimmers), sensores de luz natural y de presencia con el fin de optimizar el uso de la energia. Este trabajo presenta los resultados de generacion de armonicas para lamparas fluorescentes, operando diferentes balastros electronicos asi como con controles electronicos. Asi mismo son presentados los efectos causados por la generacion de componentes armonicas por el sistema de iluminacion dentro del sistema electrico que van desde la distorsion en voltaje y corriente, la presencia de corrientes dentro del conductor neutro en sistemas balanceados, asi como la repercusion en los equipos de medicion tales

Design and Simulation of Automatic Ballast System on Catamaran Ship Based on Programmable Logic Control

Directory of Open Access Journals (Sweden)

Indra Ranu Kusuma

2017-06-01

Full Text Available Characteristics of catamaran ship which has deficiency to ship stability during maneuvering. to that end, this paper concerns about ballast system design in support of the safety and comfort of passengers on the catamaran boat. the discussion is done by creating a mathematical model of each component in the block diagram of the ballast system. then determine the pid value of the system and add the compensator for the system to run stable. further analyzed with the help of matlab software to get transient system response. with the automation system on the ballast system, it is expected that the motion of the ship can work automatically and provide a better response in the stability of the catamaran type ship. the ballast system begins to work against the tilt of the ship at 6.7 seconds at a certain angle, and will continue to work during the vessel maneuvering. judging from the 6.7 second system response time, the convenience of the passengers is not disturbed (the system response is not too fast. one way to reduce the rolling that occurs on the ship is to optimize the performance of the ballast system. performance optimization is done by using programmable logic controller (plc. plc used is omron cpm1a-30cdr-a-v1. the process is done by making the installation plant model of the ballast system as a control medium. followed by creating a control circuit consisting of wiring i / o, limit switch circuits, power supplies and programming languages associated with plcs. the result of the control is expected to regulate fluid flow in the ballast system automatically resulting in a rapid response to the stability of the ship.

Uncertainty and sensitivity analyses of ballast life-cycle cost and payback period

OpenAIRE

Mcmahon, James E.

2000-01-01

The paper introduces an innovative methology for evaluating the relative significance of energy-efficient technologies applied to fluorescent lamp ballasts. The method involves replacing the point estimates of life cycle cost of the ballasts with uncertainty distributions reflecting the whole spectrum of possible costs, and the assessed probability associated with each value. The results of uncertainty and sensitivity analyses will help analysts reduce effort in data collection and carry on a...

Stratification of living organisms in ballast tanks: how do organism concentrations vary as ballast water is discharged?

Science.gov (United States)

First, Matthew R; Robbins-Wamsley, Stephanie H; Riley, Scott C; Moser, Cameron S; Smith, George E; Tamburri, Mario N; Drake, Lisa A

2013-05-07

Vertical migrations of living organisms and settling of particle-attached organisms lead to uneven distributions of biota at different depths in the water column. In ballast tanks, heterogeneity could lead to different population estimates depending on the portion of the discharge sampled. For example, concentrations of organisms exceeding a discharge standard may not be detected if sampling occurs during periods of the discharge when concentrations are low. To determine the degree of stratification, water from ballast tanks was sampled at two experimental facilities as the tanks were drained after water was held for 1 or 5 days. Living organisms ≥50 μm were counted in discrete segments of the drain (e.g., the first 20 min of the drain operation, the second 20 min interval, etc.), thus representing different strata in the tank. In 1 and 5 day trials at both facilities, concentrations of organisms varied among drain segments, and the patterns of stratification varied among replicate trials. From numerical simulations, the optimal sampling strategy for stratified tanks is to collect multiple time-integrated samples spaced relatively evenly throughout the discharge event.

Identification of high-speed rail ballast flight risk factors and risk mitigation strategies - final report.

Science.gov (United States)

2015-04-01

The phenomenon of flying ballast is well-documented in high-speed rail operations. Displaced ballast particles from the track bed : may cause damage to rolling stock as well as the track infrastructure, and wayside structures close to the right of wa...

Development of an ATP assay for rapid onboard testing to detect living microorganisms in ballast water

Science.gov (United States)

Hyun, Bonggil; Cha, Hyung-Gon; Lee, Nayoung; Yum, Seungshic; Baek, Seung Ho; Shin, Kyoungsoon

2018-03-01

Ballast water is a principal pathway for the introduction of pathogens and non-indigenous species to ports worldwide. The International Maritime Organization (IMO) and the United States Coast Guard (USCG) have adopted ballast water management regulations that require, e.g., the installation of shipboard ballast water management systems (BWMS). Rapid and simple analytical methods are needed to monitor whether ballast water disinfection ensures compliance with the discharge standards. In this study laboratory and full scale land-based testing was used to investigate the suitability of an adenosine triphosphate (ATP) assay for quantifying living organisms (≥ 10 and land-based testing the ATP assay also showed a good correlation with the presence of living natural plankton cells in control samples, but the ATP concentration (137 pg mL- 1) was much lower than the ATP guideline. The low ATP concentration in natural plankton cells may reflect a decline in their biological activity because of extended exposure to dark conditions. Although our results need further validation, the ATP assay is a suitable tool for monitoring compliance of ballast water treatment.

Inactivation of Heterosigma akashiwo in ballast water by circular orifice plate-generated hydrodynamic cavitation.

Science.gov (United States)

Feng, Daolun; Zhao, Jie; Liu, Tian

2016-01-01

The discharge of alien ballast water is a well-known, major reason for marine species invasion. Here, circular orifice plate-generated hydrodynamic cavitation was used to inactivate Heterosigma akashiwo in ballast water. In comparison with single- and multihole orifice plates, the conical-hole orifice plate yielded the highest inactivation percentage, 51.12%, and consumed only 6.84% energy (based on a 50% inactivation percentage). Repeating treatment, either using double series-connection or circling inactivation, elevated the inactivation percentage, yet consumed much more energy. The results indicate that conical-hole-generated hydrodynamic cavitation shows great potential as a pre-inactivation method for ballast water treatment.

Model track studies on fouled ballast using ground penetrating radar and multichannel analysis of surface wave

Science.gov (United States)

Anbazhagan, P.; Lijun, Su; Buddhima, Indraratna; Cholachat, Rujikiatkamjorn

2011-08-01

Ballast fouling is created by the breakdown of aggregates or outside contamination by coal dust from coal trains, or from soil intrusion beneath rail track. Due to ballast fouling, the conditions of rail track can be deteriorated considerably depending on the type of fouling material and the degree of fouling. So far there is no comprehensive guideline available to identify the critical degree of fouling for different types of fouling materials. This paper presents the identification of degree of fouling and types of fouling using non-destructive testing, namely seismic surface-wave and ground penetrating radar (GPR) survey. To understand this, a model rail track with different degree of fouling has been constructed in Civil engineering laboratory, University of Wollongong, Australia. Shear wave velocity obtained from seismic survey has been employed to identify the degree of fouling and types of fouling material. It is found that shear wave velocity of fouled ballast increases initially, reaches optimum fouling point (OFP), and decreases when the fouling increases. The degree of fouling corresponding after which the shear wave velocity of fouled ballast will be smaller than that of clean ballast is called the critical fouling point (CFP). Ground penetrating radar with four different ground coupled antennas (500 MHz, 800 MHz, 1.6 GHz and 2.3 GHz) was also used to identify the ballast fouling condition. It is found that the 800 MHz ground coupled antenna gives a better signal in assessing the ballast fouling condition. Seismic survey is relatively slow when compared to GPR survey however it gives quantifiable results. In contrast, GPR survey is faster and better in estimating the depth of fouling.

Survey on germination and species composition of dinoflagellates from ballast tanks and recent sediments in ports on the South Coast of Finland, North-Eastern Baltic Sea

Energy Technology Data Exchange (ETDEWEB)

Pertola, Sari [Finnish Institute of Marine Research, Department of Biological Research, P.O. Box 2, FI-00561 Helsinki (Finland)]. E-mail sari.pertola@fimr.fi; Faust, Maria A. [Department of Botany, US National Herbarium, Smithsonian Institution, 4210 Silver Hill Road, Suitland, Maryland 20746 (United States); Kuosa, Harri [Tvaerminne Zoological Station, University of Helsinki, FI-10900 Hanko (Finland)

2006-08-15

Cyst beds in ships and ports in Finland have previously been unstudied. Therefore, sediments from ships' ballast water tanks and four Finnish ports were sampled for dinoflagellate cysts and other phytoplankton. Untreated sediments were incubated at 10 {sup o}C and 20 {sup o}C in the local 6 psu salinity for 1, 4 and 7 days, and vegetative cells were examined with light and scanning electron microscope. Sediments were inhabited by various dinoflagellates, diatoms, chlorophytes, cyanophytes and small flagellates. Germinated dinoflagellates were found in 90% of ballast tanks and in all ports. Gymnodiniales spp. and Heterocapsa rotundata formed a major proportion of the proliferating dinoflagellate cells. One species, Peridinium quinquecorne, not previously reported from the Baltic Sea, was identified with SEM. The study emphasises that ships are potential transport vehicles for dinoflagellate cysts even in the low salinity Finnish waters, and small-sized dinoflagellates should be focused upon in ballast water studies.

Ballast Water Treatment Corrosion Scoping Study

Science.gov (United States)

2011-10-01

NANPCA Nonindigenous Aquatic Nuisance Prevention and Control Act NaCl Sodium Chloride NIOZ Nederlands Instituut voor Onderzoek der Zee NISA National...Based Testing Report on the Ecochlor System performed by Nederlands Instituut voor Onderzoek der Zee (NIOZ) (Veldhuis, 2008), ballast water treated...and the Relevant IMO Guideline. Nederlands Instituut voor Onderzoek der Zee (NIOZ). Den Burg: Royal Netherlands Institute for Sea Research. Volkening

33 CFR 151.2037 - If my vessel cannot conduct ballast water management practices because of its voyage and/or...

Science.gov (United States)

2010-07-01

... ballast water management practices because of its voyage and/or safety concerns, will I be prohibited from... is inoperable must employ one of the other ballast water management practices stated in § 151.2035(b). If the vessel cannot employ other ballast water management practices due to voyage or safety concerns...

[Verification of ballast water exchange for international ships anchored in Xiamen Port by CDOM tracer].

Science.gov (United States)

Li, Chao; Zhang, Yan-po; Guo, Wei-dong; Zhu, Yue; Xu, Jing; Deng, Xun

2010-09-01

Fluorescence excitation-emission matrix (EEM) and absorption spectroscopy were applied to study the optical properties of 29 CDOM samples collected from different ballast tanks of nine international route vessels anchored in Xiamen Port between October 2007 and April 2008. The purpose was to examine the feasibility of these spectral properties as a tracer to verify if these vessels follow the mid-ocean ballast water exchange (BWE) regulation. Using parallel factor analysis, four fluorescent components were identified, including two humic-like components (C1: 245, 300/386 nm; C2: 250, 345/458 nm) and two protein-like components (C3: 220, 275/306 nm; C4: 235, 290/345 nm), of which C2 component was the suitable fluorescence verification indicator. The vertical distribution of all fluorescent components in ballast tank was nearly similar indicating that profile-mixing sampling was preferable. Combined use of C2 component, spectral slope ratio (SR) of absorption spectroscopy and salinity may provide reasonable verification if BWE carried out by these nine ships. The results suggested that the combined use of multiple parameters (fluorescence, absorption and salinity) would be much reliable to determine the origin of ballast water, and to provide the technical guarantee for fast examination of ballast water exchange in Chinese ports.

Magnetic fluorescent ballasts: Market data, market imperfections, and policy success

Energy Technology Data Exchange (ETDEWEB)

Koomey, J.G.; Sanstad, A.H.; Shown, L.J.

1995-12-01

Many economists have strongly questioned engineering-economic studies aimed at demonstrating anomalously slow diffusion of energy-efficient technology and the benefits of regulations to promote such technology. One argument against such studies is that standard techniques of engineering-economics are either inappropriate for or are routinely misapplied in assessing the performance of the market for energy efficiency. This paper presents engineering-economic evidence on the diffusion of energy efficiency improvements that takes account of such critiques. The authors examine the engineering and economic characteristics of standard and energy-efficient magnetic ballasts for fluorescent lighting. Efficient magnetic ballasts represented an excellent investment for 99% of the commercial building floor stock, and a moderately good investment for 0.7% of the commercial floor stock. Still, these ballasts were only being adopted in the 1980s at a rate commensurate with the enactment of appliance efficiency standards in various states. In this case, there is solid empirical evidence for skepticism about the effectiveness of the market mechanism in promoting cost-effective energy efficiency improvements as well as evidence of the benefits of regulation to counteract this shortcoming.

Effect of particle breakage on cyclic densification of ballast: A DEM approach

International Nuclear Information System (INIS)

Thakur, P K; Vinod, J S; Indraratna, B

2010-01-01

In this paper, an attempt has been made to investigate the effect of particle breakage on densification behaviour of ballast under cyclic loading using Discrete Element Method (DEM). Numerical simulations using PFC 2D have been carried out on an assembly of angular particles with and without incorporation of particle breakage. Two-dimensional projection of angular ballast particles were simulated using clusters of bonded circular particles. Degradation of the bonds within a cluster was considered to represent particle breakage. Clump logic was used to make the cluster of particles unbreakable. DEM simulation results highlight that the particle breakage has a profound influence on the cyclic densification behaviour of ballast. The deformation behaviour exhibited by the assembly with breakage is in good agreement with the laboratory experiments. In addition, the evolution of particle displacement vectors clearly explains the breakage mechanism and associated deformations during cyclic loading.

Interior LED Lighting Technology. Navy Energy Technology Validation (Techval) Program

Science.gov (United States)

2015-09-01

usually on most of the time. • Consider replacing existing CFL, high-intensity discharge (HID), or halogen lamp light fixtures/ lamps with LED fixtures... lamps . What is the Technology? An LED is a semiconductor-diode that emits light when power is applied. A driver is used, much as a ballast, to...available in integrated luminaires that can be used to replace existing luminaires. LEDs are also available as direct replacement lamps for many

Examination of an indicative tool for rapidly estimating viable organism abundance in ballast water

Science.gov (United States)

Vanden Byllaardt, Julie; Adams, Jennifer K.; Casas-Monroy, Oscar; Bailey, Sarah A.

2018-03-01

Regulatory discharge standards stipulating a maximum allowable number of viable organisms in ballast water have led to a need for rapid, easy and accurate compliance assessment tools and protocols. Some potential tools presume that organisms present in ballast water samples display the same characteristics of life as the native community (e.g. rates of fluorescence). This presumption may not prove true, particularly when ships' ballast tanks present a harsh environment and long transit times, negatively impacting organism health. Here, we test the accuracy of a handheld pulse amplitude modulated (PAM) fluorometer, the Hach BW680, for detecting photosynthetic protists at concentrations above or below the discharge standard (< 10 cells·ml- 1) in comparison to microscopic counts using fluorescein diacetate as a viability probe. Testing was conducted on serial dilutions of freshwater harbour samples in the lab and in situ untreated ballast water samples originating from marine, freshwater and brackish sources utilizing three preprocessing techniques to target organisms in the size range of ≥ 10 and < 50 μm. The BW680 numeric estimates were in agreement with microscopic counts when analyzing freshly collected harbour water at all but the lowest concentrations (< 38 cells·ml- 1). Chi-square tests determined that error is not independent of preprocessing methods: using the filtrate method or unfiltered water, in addition to refining the conversion factor of raw fluorescence to cell size, can decrease the grey area where exceedance of the discharge standard cannot be measured with certainty (at least for the studied populations). When examining in situ ballast water, the BW680 detected significantly fewer viable organisms than microscopy, possibly due to factors such as organism size or ballast water age. Assuming both the BW680 and microscopy with FDA stain were measuring fluorescence and enzymatic activity/membrane integrity correctly, the observed discrepancy

Comparative feasibility study on retrofitting ballast water treatment system for a bulk carrier.

Science.gov (United States)

Jee, Jaehoon; Lee, Sangick

2017-06-30

Use of ballast water in ships causes harmful effects on marine environment accompanied by economic loss and negative impact on ecosystem and human health. To solve these problems, the international convention on ballast water management will take into force in September 2017. In this study, a comprehensive feasibility of retrofitting the ballast water treatment system for an ocean-going bulk carrier was conducted. The technologies involved, installation and operational aspects of direct flow and side stream electrolysis, UV, and ozone type BWTS are described in detail. The principal concept of each BWTS is explained and probable arrangements of retrofitting in engine room are suggested. The cost analysis is carried out for retrofitting 4 types of BWTS onboard the target ship by examining each processes of installation and operation. Copyright © 2017 Elsevier Ltd. All rights reserved.

Which Ballast Water Management System Will You Put Aboard? Remnant Anxieties: A Mini-Review

Directory of Open Access Journals (Sweden)

William R. Batista

2017-08-01

Full Text Available An accepted solution to the environmental problems related to a ship’s ballast water has been the adoption and proper utilization of approved onboard ballast water plans and management systems (BWMS. On 8 September 2017, the International Maritime Organization Ballast Water Management Convention comes into force, and under this Convention, ships engaged in international trade must have an approved BWMS aboard to discharge ballast water, reducing species transfer. In response to enormous global concern about this problem, the overwhelming majority of the BWMS, approved currently for use by International Maritime Organization (IMO and United States Coast Guard, utilize two main technologies (electro-chlorination or ultraviolet irradiation as their principle mode of disinfection, often used in combination with filtration. However, both technologies have been questioned regarding their practically, efficiency, and possible environmental impacts upon discharge. This review article aims to explore some questions about these two technologies, drawing attention to some current uncertainties associated with their use. Also, it draws attention to some technical obstacles and regulatory impediments related to the new development of green biocide technology, which largely has been ignored, despite its potential as a simpler, cleaner and effective technology.

Evaluating efficacy of filtration + UV-C radiation for ballast water treatment at different temperatures

Science.gov (United States)

Casas-Monroy, Oscar; Linley, Robert D.; Chan, Po-Shun; Kydd, Jocelyn; Vanden Byllaardt, Julie; Bailey, Sarah

2018-03-01

To prevent new ballast water-mediated introductions of aquatic nonindigenous species (NIS), many ships will soon use approved Ballast Water Management Systems (BWMS) to meet discharge standards for the maximum number of viable organisms in ballast water. Type approval testing of BWMS is typically conducted during warmer seasons when plankton concentrations are highest, despite the fact that ships operate globally year-round. Low temperatures encountered in polar and cool temperate climates, particularly during the winter season, may impact treatment efficacy through changes in plankton community composition, biological metabolic rates or chemical reaction rates. Filtration + UV irradiance is one of the most common ballast water treatment methods, but its effectiveness at low temperatures has not been assessed. The objective in this study was to examine the efficacy of filtration + UV-C irradiation treatment at low temperatures for removal or inactivation of phytoplankton and zooplankton populations during simulated ballast water treatment. Organisms from two size classes (≥ 10 to < 50 μm and ≥ 50 μm) were identified and enumerated using microscope and culture techniques. The response of organisms in both size categories to UV-C irradiation was evident across a range of temperatures (18 °C, 12 °C and 2 °C) as a significant decrease in concentration between controls and treated samples. Results indicate that filtration + UV-C irradiation will be effective at low temperatures, with few viable organisms ≥ 10 to < 50 μm recorded even 21 days following UV exposure (significantly lower than in the control treatment).

77 FR 33969 - Standards for Living Organisms in Ships' Ballast Water Discharged in U.S. Waters

Science.gov (United States)

2012-06-08

...-10486] RIN 1625-AA32 Standards for Living Organisms in Ships' Ballast Water Discharged in U.S. Waters... Living Organisms in Ships' Ballast Water Discharged in U.S. Waters.'' Six technical errors were.... Waters.'' Six technical errors were inadvertently published in the final rule that require correction...

Nucleic acids-based tools for ballast water surveillance, monitoring, and research

Science.gov (United States)

Darling, John A.; Frederick, Raymond M.

2018-03-01

Understanding the risks of biological invasion posed by ballast water-whether in the context of compliance testing, routine monitoring, or basic research-is fundamentally an exercise in biodiversity assessment, and as such should take advantage of the best tools available for tackling that problem. The past several decades have seen growing application of genetic methods for the study of biodiversity, driven in large part by dramatic technological advances in nucleic acids analysis. Monitoring approaches based on such methods have the potential to increase dramatically sampling throughput for biodiversity assessments, and to improve on the sensitivity, specificity, and taxonomic accuracy of traditional approaches. The application of targeted detection tools (largely focused on PCR but increasingly incorporating novel probe-based methodologies) has led to a paradigm shift in rare species monitoring, and such tools have already been applied for early detection in the context of ballast water surveillance. Rapid improvements in community profiling approaches based on high throughput sequencing (HTS) could similarly impact broader efforts to catalogue biodiversity present in ballast tanks, and could provide novel opportunities to better understand the risks of biotic exchange posed by ballast water transport-and the effectiveness of attempts to mitigate those risks. These various approaches still face considerable challenges to effective implementation, depending on particular management or research needs. Compliance testing, for instance, remains dependent on accurate quantification of viable target organisms; while tools based on RNA detection show promise in this context, the demands of such testing require considerable additional investment in methods development. In general surveillance and research contexts, both targeted and community-based approaches are still limited by various factors: quantification remains a challenge (especially for taxa in larger size

Catch me if you can: Comparing ballast water sampling skids to traditional net sampling

Science.gov (United States)

Bradie, Johanna; Gianoli, Claudio; Linley, Robert Dallas; Schillak, Lothar; Schneider, Gerd; Stehouwer, Peter; Bailey, Sarah

2018-03-01

With the recent ratification of the International Convention for the Control and Management of Ships' Ballast Water and Sediments, 2004, it will soon be necessary to assess ships for compliance with ballast water discharge standards. Sampling skids that allow the efficient collection of ballast water samples in a compact space have been developed for this purpose. We ran 22 trials on board the RV Meteor from June 4-15, 2015 to evaluate the performance of three ballast water sampling devices (traditional plankton net, Triton sampling skid, SGS sampling skid) for three organism size classes: ≥ 50 μm, ≥ 10 μm to Natural sea water was run through the ballast water system and untreated samples were collected using paired sampling devices. Collected samples were analyzed in parallel by multiple analysts using several different analytic methods to quantify organism concentrations. To determine whether there were differences in the number of viable organisms collected across sampling devices, results were standardized and statistically treated to filter out other sources of variability, resulting in an outcome variable representing the mean difference in measurements that can be attributed to sampling devices. These results were tested for significance using pairwise Tukey contrasts. Differences in organism concentrations were found in 50% of comparisons between sampling skids and the plankton net for ≥ 50 μm, and ≥ 10 μm to < 50 μm size classes, with net samples containing either higher or lower densities. There were no differences for < 10 μm organisms. Future work will be required to explicitly examine the potential effects of flow velocity, sampling duration, sampled volume, and organism concentrations on sampling device performance.

Ballast minerals and the sinking carbon flux in the ocean: carbon-specific respiration rates and sinking velocity of marine snow aggregates

Directory of Open Access Journals (Sweden)

M. H. Iversen

2010-09-01

Full Text Available Recent observations have shown that fluxes of ballast minerals (calcium carbonate, opal, and lithogenic material and organic carbon fluxes are closely correlated in the bathypelagic zones of the ocean. Hence it has been hypothesized that incorporation of biogenic minerals within marine aggregates could either protect the organic matter from decomposition and/or increase the sinking velocity via ballasting of the aggregates. Here we present the first combined data on size, sinking velocity, carbon-specific respiration rate, and composition measured directly in three aggregate types; Emiliania huxleyi aggregates (carbonate ballasted, Skeletonema costatum aggregates (opal ballasted, and aggregates made from a mix of both E. huxleyi and S. costatum (carbonate and opal ballasted. Overall average carbon-specific respiration rate was ~0.13 d⁻¹ and did not vary with aggregate type and size. Ballasting from carbonate resulted in 2- to 2.5-fold higher sinking velocities than those of aggregates ballasted by opal. We compiled literature data on carbon-specific respiration rate and sinking velocity measured in aggregates of different composition and sources. Compiled carbon-specific respiration rates (including this study vary between 0.08 d⁻¹ and 0.20 d⁻¹. Sinking velocity increases with increasing aggregate size within homogeneous sources of aggregates. When compared across different particle and aggregate sources, however, sinking velocity appeared to be independent of particle or aggregate size. The carbon-specific respiration rate per meter settled varied between 0.0002 m⁻¹ and 0.0030 m⁻¹, and decreased with increasing aggregate size. It was lower for calcite ballasted aggregates as compared to that of similar sized opal ballasted aggregates.

A Study of Ballast Water Treatment Using Engine Waste Heat

Science.gov (United States)

Balaji, Rajoo; Yaakob, Omar; Koh, Kho King; Adnan, Faizul Amri bin; Ismail, Nasrudin bin; Ahmad, Badruzzaman bin; Ismail, Mohd Arif bin

2018-05-01

Heat treatment of ballast water using engine waste heat can be an advantageous option complementing any proven technology. A treatment system was envisaged based on the ballast system of an existing, operational crude carrier. It was found that the available waste heat could raise the temperatures by 25 °C and voyage time requirements were found to be considerable between 7 and 12 days to heat the high volumes of ballast water. Further, a heat recovery of 14-33% of input energies from exhaust gases was recorded while using a test rig arrangement representing a shipboard arrangement. With laboratory level tests at temperature ranges of around 55-75 °C, almost complete species mortalities for representative phytoplankton, zooplankton and bacteria were observed while the time for exposure varied from 15 to 60 s. Based on the heat availability analyses for harvesting heat from the engine exhaust gases(vessel and test rig), heat exchanger designs were developed and optimized using Lagrangian method applying Bell-Delaware approaches. Heat exchanger designs were developed to suit test rig engines also. Based on these designs, heat exchanger and other equipment were procured and erected. The species' mortalities were tested in this mini-scale arrangement resembling the shipboard arrangement. The mortalities realized were > 95% with heat from jacket fresh water and exhaust gases alone. The viability of the system was thus validated.

Study on the killing of oceanic harmful micro-organisms in ship's ballast water using oxygen active particles

International Nuclear Information System (INIS)

Chen, C; Meng, X Y; Bai, M D; Tian, Y P; Jing, Y

2013-01-01

Global Environment Facility has identified that the spread of marine invasive alien species is one of the four major risk factors threatening the safety of global marine environments. Ballast water discharge is the main cause of biological invasion. With physical methods of strong electric field ionization discharge at atmospheric pressure, O 2 and sea water (gaseous) were ionized, and then dissociated to a number of oxygen active particles (ROS) such as ·OH, O 2 + , H 2 O + , etc. ROS was injected into 0.6 t h −1 ballast water treatment system to form high concentration ROS solution in order to kill the harmful micro-organisms in ballast water. According to the land-based test standard of International Maritime Organization (IMO) Guidelines for Approval of Ballast Water Management Systems (G8), this paper concludes that single-cell algae of 3.0 × 10 4 cell ml −1 and bacteria of 2.0 × 10 4 cfu ml −1 were killed by ROS solution of 2.0 ppm. Death rate could reach almost 100%. The results meet the requirements of Regulation D-2 of International Convention for the Control and Management of Ships' Ballast Water and Sediments completely.

Uncertainty and sensitivity analyses of ballast life-cycle cost and payback period

Energy Technology Data Exchange (ETDEWEB)

McMahon, James E.; Liu, Xiaomin; Turiel, Ike; Hakim, Sajid; Fisher, Diane

2000-06-01

The paper introduces an innovative methodology for evaluating the relative significance of energy-efficient technologies applied to fluorescent lamp ballasts. The method involves replacing the point estimates of life cycle cost of the ballasts with uncertainty distributions reflecting the whole spectrum of possible costs, and the assessed probability associated with each value. The results of uncertainty and sensitivity analyses will help analysts reduce effort in data collection and carry on analysis more efficiently. These methods also enable policy makers to gain an insightful understanding of which efficient technology alternatives benefit or cost what fraction of consumers, given the explicit assumptions of the analysis.

Ship board testing of a deoxygenation ballast water treatment.

Science.gov (United States)

McCollin, Tracy; Quilez-Badia, Gemma; Josefsen, Kjell D; Gill, Margaret E; Mesbahi, Ehsan; Frid, Chris L J

2007-08-01

A ship board trial of a deoxygenation method for treating ballast water was carried out during a voyage from Southampton (United Kingdom) to Manzanillo (Panama). A nutrient solution added to two ballast tanks encouraged bacterial growth, resulting in a gradual change to an anoxic environment. Samples were taken from two treated tanks and two untreated tanks to assess changes in the abundance and viability of zooplankton, phytoplankton and bacteria. The work was carried out before the International Maritime Organization (IMO) standard was agreed so only a broad indication of whether the results achieved the standard was given. For the zooplankton, the standard would have been achieved within 5 or 7 days but the phytoplankton results were inconclusive. The biological efficacy was the result of the combination of several factors, including the treatment, pump damage and an increase in the water temperature during the voyage.

Numerical simulation on stir system of jet ballast in high level liquid waste storage tank

International Nuclear Information System (INIS)

Lu Yingchun

2012-01-01

The stir system of jet ballast in high level liquid waste storage tank was simulation object. Gas, liquid and solid were air, sodium nitrate liquor and titanium whitening, respectively. The mathematic model based on three-fluid model and the kinetic theory of particles was established for the stir system of jet ballast in high level liquid waste storage tank. The CFD commercial software was used for solving this model. The detail flow parameters as three phase velocity, pressure and phase loadings were gained. The calculated results agree with the experimental results, so they can well define the flow behavior in the tank. And this offers a basic method for the scale-up and optimization design of the stir system of jet ballast in high level liquid waste storage tank. (author)

77 FR 17082 - Standards for Living Organisms in Ships' Ballast Water Discharged in U.S. Waters: Final...

Science.gov (United States)

2012-03-23

... standard will be used to approve ballast water management methods that are effective in preventing or reducing the introduction of nonindigenous species via discharged ballast water into waters of the United....regulations.gov on or before April 23, 2012 or reach the Docket Management Facility by that date. ADDRESSES...

Chamber study of PCB emissions from caulking materials and light ballasts.

Science.gov (United States)

Liu, Xiaoyu; Guo, Zhishi; Krebs, Kenneth A; Stinson, Rayford A; Nardin, Joshua A; Pope, Robert H; Roache, Nancy F

2015-10-01

The emissions of polychlorinated biphenyl (PCB) congeners from thirteen caulk samples were tested in a micro-chamber system. Twelve samples were from PCB-contaminated buildings and one was prepared in the laboratory. Nineteen light ballasts collected from buildings that represent 13 different models from five manufacturers were tested in 53-L environmental chambers. The rates of PCB congener emissions from caulking materials and light ballasts were determined. Several factors that may have affected the emission rates were evaluated. The experimentally determined emission factors showed that, for a given PCB congener, there is a linear correlation between the emission factor and the concentration of the PCB congener in the source. Furthermore, the test results showed that an excellent log-linear correlation exists between the normalized emission factor and the vapor pressure (coefficient of determination, r(2)⩾0.8846). The PCB congener emissions from ballasts at or near room temperature were relatively low with or without electrical load. However, the PCB congener emission rates increased significantly as the temperature increased. The results of this research provide new data and models for ranking the primary sources of PCBs and supports the development and refinement of exposure assessment models for PCBs. Published by Elsevier Ltd.

A Comparison of Microbial Water Quality and Diversity for Ballast and Tropical Harbor Waters.

Science.gov (United States)

Ng, Charmaine; Le, Thai-Hoang; Goh, Shin Giek; Liang, Liang; Kim, Yiseul; Rose, Joan B; Yew-Hoong, Karina Gin

2015-01-01

Indicator organisms and antibiotic resistance were used as a proxy to measure microbial water quality of ballast tanks of ships, and surface waters in a tropical harbor. The survival of marine bacteria in ballast tanks appeared to diminish over longer water retention time, with a reduction of cell viability observed after a week based on heterotrophic plate counts. Pyrosequencing of 16S rRNA genes showed distinct differences in microbial composition of ballast and harbor waters. The harbor waters had a higher abundance of operational taxonomic units (OTUs) assigned to Cyanobacteria (Synechococcus spp.) and α-proteobacteria (SAR11 members), while marine hydrocarbon degraders such as γ-proteobacteria (Ocenspirillaes spp., Thiotrchales spp.) and Bacteroidetes (Flavobacteriales spp.) dominated the ballast water samples. Screening of indicator organisms found Escherichia coli (E. coli), Enterococcus and Pseudomonas aeruginosa (P. aeruginosa) in two or more of the ballast and harbor water samples tested. Vibrio spp. and Salmonella spp. were detected exclusively in harbor water samples. Using quantitative PCR (qPCR), we screened for 13 antibiotic resistant gene (ARG) targets and found higher abundances of sul1 (4.13-3.44 x 102 copies/mL), dfrA (0.77-1.80 x10 copies/mL) and cfr (2.00-5.21 copies/mL) genes compared to the other ARG targets selected for this survey. These genes encode for resistance to sulfonamides, trimethoprim and chloramphenicol-florfenicol antibiotics, which are also known to persist in sediments of aquaculture farms and coastal environments. Among the ARGs screened, we found significant correlations (Pwater quality survey, quantitatively assessing indicators of antibiotic resistance, potentially pathogenic organisms and a broad-brush description of difference in microbial composition and diversity between open oceans and tropical coastal environments through the use of next generation sequencing technology.

Ship traffic and the introduction of diatoms and dinoflagellates via ballast water in the port of Annaba, Algeria

Science.gov (United States)

Cheniti, Radhia; Rochon, André; Frihi, Hocine

2018-03-01

We present here the first study on the role of ship traffic in the introduction of potentially harmful and/or non-indigenous species in the port of Annaba (Algeria). A total of 25 ships of two different types (general cargo and bulk carriers) were sampled and separated into two categories: oceanic and Mediterranean ships. We estimated propagule pressure of high-risk coastal phytoplankton delivered in ballast water to the port of Annaba. We identified 40 diatom and 38 dinoflagellate taxa, among which, 11 harmful/toxic taxa: Pseudo-nitzschia spp., Alexandrium tamarense, Alexandrium sp., Dinophysis acuminata, Dinophysis rotundata, Dinophysis sp., Gonyaulax spinifera, Gymnodinium catenatum, Lingulodinium polyedrum, Protoceratium reticulatum and cyst of Alexandrium sp. In addition, 8 taxa (5 diatoms, 1 dinoflagellate and 2 dinoflagellate cysts) never observed in the Annaba region were considered as potentially non-indigenous: Actinoptychus splendens, Coscinodiscus asteromphalus, Coscinodiscus lineatus, Odentella granulata, Thalassiosira cf. decipiens, Prorocentrum scutellum, cyst of Polykrikos kofoidii and Islandinium minutum. Several factors were examined, including ship routes, ballast water age and the volume of ballast water discharged. Our analyses revealed that diatom and dinoflagellate abundances decreased with ballast water age, possibly as a result of mortality of species due to voyage length and lack of light in ballast tanks. Estimates of actual propagule pressure, diatoms and dinoflagellates abundances varied from 1 to 4 × 108 cells/ship. The results of this study could serve as the baseline for the development and implementation of monitoring and ballast water management programs in ports of Algeria.

Continuously forced ballast resistor model for superconducting hot spots

International Nuclear Information System (INIS)

Ausloos, M.

1981-01-01

To neglect the Thomson effect in the ballast resistor theory is an incorrect assumption since it measures the velocity of the thermal grain boundaries. Due to the constant rate of heating or cooling, large oscillations are predicted in dR/dT near Tsub(c). (orig.)

Effects of Hydroxyl Radicals on Introduced Organisms of Ship's Ballast Water Based Micro-Gap Discharge

International Nuclear Information System (INIS)

Bai Mindong; Zhang Zhitao; Bai Mindi; Yang Bo; Bai Xiyao

2007-01-01

With the physical method of micro-gap gas discharge, OH· radicals were produced by the ionization of O 2 in air and H 2 O in the gaseous state, in order to explore more effective method to treat the ship's ballast water. The surface morphology of Al 2 O 3 dielectric layer was analysed using Atomic Force Microscopy (AFM), where the size of Al 2 O 3 particles was in the range of 2 μm to 5 μm. At the same time, the biochemical effect of hydroxyl radicals on the introduced organisms and the quality of ship's ballast water were studied. The results indicate that the main reasons of cell death are lipid peroxide and damage of the antioxidant enzyme system in Catalase (CAT), Peroxidase (POD) and Superoxide dismutase (SOD). In addition, the quality of the ballast water was greatly improved

Design and fabrication of carbon nanotube field-emission cathode with coaxial gate and ballast resistor.

Science.gov (United States)

Sun, Yonghai; Yeow, John T W; Jaffray, David A

2013-10-25

A low density vertically aligned carbon nanotube-based field-emission cathode with a ballast resistor and coaxial gate is designed and fabricated. The ballast resistor can overcome the non-uniformity of the local field-enhancement factor at the emitter apex. The self-aligned fabrication process of the coaxial gate can avoid the effects of emitter tip misalignment and height non-uniformity. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

46 CFR 56.50-50 - Bilge and ballast piping.

Science.gov (United States)

2010-10-01

... or in the boiler or machinery space, including spaces in which oil settling tanks or oil pumping... pumping from and draining any watertight compartment except for ballast, oil and water tanks which have... the suction pipes. Efficient means shall be provided for draining water from all tank tops, other...

Indirectly heated biomass gasification using a latent-heat ballast-part 3: refinement of the heat transfer model

International Nuclear Information System (INIS)

Cummer, Keith; Brown, Robert C.

2005-01-01

An indirectly heated gasifier is under development at Iowa State University. This gasifier integrates a latent-heat ballast with a fluidized-bed reactor. The latent heat ballast is an array of stainless-steel tubes filled with lithium fluoride, which is a high-temperature phase-change material (PCM). Previous studies have presented experimental results from the gasifier and described a mathematical model of the pyrolysis phase of the cyclic gasification process. This model considers both heat transfer and chemical reactions that occur during pyrolysis, but discrepancies between model predictions and experimental data have demonstrated the need to refine the model. In particular, cooling curves for the ballasting system are not well predicted during phase change of the lithium fluoride. A reformulated model, known as the Receding Interface (RI) model, postulates the existence of a receding liquid phase within the ballast tubes as they cool, which progressively decreases the rate of heat transfer from the tubes. The RI model predicts behavior that is more consistent with experimental results during the phase-change process, while retaining accuracy before and after the process of phase change

A New Treatment Strategy for Inactivating Algae in Ballast Water Based on Multi-Trial Injections of Chlorine.

Science.gov (United States)

Sun, Jinyang; Wang, Junsheng; Pan, Xinxiang; Yuan, Haichao

2015-06-09

Ships' ballast water can carry aquatic organisms into foreign ecosystems. In our previous studies, a concept using ion exchange membrane electrolysis to treat ballast water has been proven. In addition to other substantial approaches, a new strategy for inactivating algae is proposed based on the developed ballast water treatment system. In the new strategy, the means of multi-trial injection with small doses of electrolytic products is applied for inactivating algae. To demonstrate the performance of the new strategy, contrast experiments between new strategies and routine processes were conducted. Four algae species including Chlorella vulgaris, Platymonas subcordiformis, Prorocentrum micans and Karenia mikimotoi were chosen as samples. The different experimental parameters are studied including the injection times and doses of electrolytic products. Compared with the conventional one trial injection method, mortality rate time (MRT) and available chlorine concentration can be saved up to about 84% and 40%, respectively, under the application of the new strategy. The proposed new approach has great potential in practical ballast water treatment. Furthermore, the strategy is also helpful for deep insight of mechanism of algal tolerance.

Application of Ion Torrent Sequencing to the Assessment of the Effect of Alkali Ballast Water Treatment on Microbial Community Diversity

Science.gov (United States)

Fujimoto, Masanori; Moyerbrailean, Gregory A.; Noman, Sifat; Gizicki, Jason P.; Ram, Michal L.; Green, Phyllis A.; Ram, Jeffrey L.

2014-01-01

The impact of NaOH as a ballast water treatment (BWT) on microbial community diversity was assessed using the 16S rRNA gene based Ion Torrent sequencing with its new 400 base chemistry. Ballast water samples from a Great Lakes ship were collected from the intake and discharge of both control and NaOH (pH 12) treated tanks and were analyzed in duplicates. One set of duplicates was treated with the membrane-impermeable DNA cross-linking reagent propidium mono-azide (PMA) prior to PCR amplification to differentiate between live and dead microorganisms. Ion Torrent sequencing generated nearly 580,000 reads for 31 bar-coded samples and revealed alterations of the microbial community structure in ballast water that had been treated with NaOH. Rarefaction analysis of the Ion Torrent sequencing data showed that BWT using NaOH significantly decreased microbial community diversity relative to control discharge (pbased principal coordinate analysis (PCoA) plots and UPGMA tree analysis revealed that NaOH-treated ballast water microbial communities differed from both intake communities and control discharge communities. After NaOH treatment, bacteria from the genus Alishewanella became dominant in the NaOH-treated samples, accounting for alkali ballast water treatment in reducing ballast water microbial diversity and demonstrated the application of new Ion Torrent sequencing techniques to microbial community studies. PMID:25222021

Model of discharge lamps with magnetic ballast

OpenAIRE

Molina, Julio; Sainz Sapera, Luis; Mesas García, Juan José; Bergas Jané, Joan Gabriel

2013-01-01

Magnetic ballast discharge lamp modeling has been extensively studied because these lamps can be an important source of harmonics. Discharge lamp models usually represent the arc voltage by a square waveform. However, this waveform can be far from actual arc voltages, which affects the accuracy of the lamp models. This paper investigates the actual arc voltage behavior of discharge lamps from laboratory measurements and proposes a novel characterization of these voltages to reformulate the co...

Monitoring of Radionuclides in Ship Ballast Water Following the Fukushima Nuclear Accident

International Nuclear Information System (INIS)

Abdul Kadir Ishak; Wo, Y.M.; Muhamat Omar

2011-01-01

Ballast water is the waters taken into the ship compartment to provide stability. It is taken on board at the port before the voyage begins and discharged at the port of call (arrival) while loading cargoes. Ballast is primarily composed of water and is full of stones, sediment, and thousands of living species. The quantity of water taken depends on the size of the ship and it can reach up to 10,000 tonnes. As a well known fact, Daiichi nuclear plant in Fukushima had released radioactive contaminated water into its surrounding sea and being dispersed by currents and tides. Therefore, ships travel between Malaysia and Japan in particular those from the affected regions and travel to Malaysia without cargoes will have a risk of transporting back radioactive contaminated water from Japan and released it at local ports. Malaysian Marine Department with the cooperation of Malaysian Nuclear Agency have been analysing the concentrations of several radionuclides in the ship's ballast water and sediment. This is to ensure the effective dosage is safe to the crews and general public as well to fulfill the permissible limit of 1 mSv/yr gazetted by the authorities. It is also to monitor that the contaminated water is not discharged into our marine environment. (author)

A Comparison of Microbial Water Quality and Diversity for Ballast and Tropical Harbor Waters.

Directory of Open Access Journals (Sweden)

Charmaine Ng

Full Text Available Indicator organisms and antibiotic resistance were used as a proxy to measure microbial water quality of ballast tanks of ships, and surface waters in a tropical harbor. The survival of marine bacteria in ballast tanks appeared to diminish over longer water retention time, with a reduction of cell viability observed after a week based on heterotrophic plate counts. Pyrosequencing of 16S rRNA genes showed distinct differences in microbial composition of ballast and harbor waters. The harbor waters had a higher abundance of operational taxonomic units (OTUs assigned to Cyanobacteria (Synechococcus spp. and α-proteobacteria (SAR11 members, while marine hydrocarbon degraders such as γ-proteobacteria (Ocenspirillaes spp., Thiotrchales spp. and Bacteroidetes (Flavobacteriales spp. dominated the ballast water samples. Screening of indicator organisms found Escherichia coli (E. coli, Enterococcus and Pseudomonas aeruginosa (P. aeruginosa in two or more of the ballast and harbor water samples tested. Vibrio spp. and Salmonella spp. were detected exclusively in harbor water samples. Using quantitative PCR (qPCR, we screened for 13 antibiotic resistant gene (ARG targets and found higher abundances of sul1 (4.13-3.44 x 102 copies/mL, dfrA (0.77-1.80 x10 copies/mL and cfr (2.00-5.21 copies/mL genes compared to the other ARG targets selected for this survey. These genes encode for resistance to sulfonamides, trimethoprim and chloramphenicol-florfenicol antibiotics, which are also known to persist in sediments of aquaculture farms and coastal environments. Among the ARGs screened, we found significant correlations (P<0.05 between ereA, ermG, cfr and tetO genes to one or more of the indicator organisms detected in this study, which may suggest that these members contribute to the environmental resistome. This study provides a baseline water quality survey, quantitatively assessing indicators of antibiotic resistance, potentially pathogenic organisms and a

Characterization of Bacteria in Ballast Water Using MALDI-TOF Mass Spectrometry

Digital Repository Service at National Institute of Oceanography (India)

Emami, K.; Askari, V.; Ullrich, M.; Mohinudeen, K.; Anil, A.C.; Khandeparker, L.; Burgess, J.G.; Mesbahi, E.

To evaluate a rapid and cost-effective method for monitoring bacteria in ballast water, several marine bacterial isolates were characterized by matrix-assisted laser desorption ionization-time of flight mass spectrometry (MALDI-TOF MS). Since...

A physical based equivalent circuit modeling approach for ballasted InP DHBT multi-finger devices at millimeter-wave frequencies

DEFF Research Database (Denmark)

Midili, Virginio; Squartecchia, Michele; Johansen, Tom Keinicke

2016-01-01

equivalent circuit description. In the first approach, the EM simulations of contact pads and ballasting network are combined with the small-signal model of the intrinsic device. In the second approach, the ballasting network is modeled with lumped components derived from physical analysis of the layout...

Is the aquatic environment sufficiently protected from chemicals discharged with treated ballast water from vessels worldwide? - A decadal environmental perspective and risk assessment.

Science.gov (United States)

David, Matej; Linders, Jan; Gollasch, Stephan; David, Jan

2018-05-24

Ballast water managements systems (BWMS) installed on vessels may use active substances to inactivate or kill organisms in the ballast water. This paper provides new insights in this global issue - discharge of hazardous disinfection by-products with ballast water and related risk assessment for the environment. Considering the possible extent of this issue, the International Maritime Organization (IMO) engaged the Joint Group of Experts on the Scientific Aspects of Marine Environmental Protection (GESAMP)-Ballast Water Working Group (BWWG) to oversee the evaluation process of BWMS that make use of active substances to prevent negative effects. We analysed all BWMS that received IMO final approval over a decade until 2017 and provide an overview of active substances used for ballast water treatment and disinfection by-products in the discharged ballast water. A risk assessment was conducted using the GESAMP-BWWG methodology for two very different commercial ports (Koper, Slovenia and Hamburg, Germany). Some relevant chemicals (chloropicrin, monochloroacetic acid, and dibromoacetonitrile) and other chemicals (isocyanuric acid and sodium thiosulphate) reached levels of concern, indicating a risk for aquatic organisms after discharge of that ballast water. From this analysis, it became clear GESAMP-BWWG worst-case scenario assumptions do not fully account for the potential environmental risks. We provide recommendations how to make this risk assessment more robust, recommend further research, and urge for policy as well as regulatory responses. Copyright © 2018 Elsevier Ltd. All rights reserved.

Evaluation of bituminous sub-ballast manufactured at low temperatures as an alternative for the construction of more sustainable railway structures

Directory of Open Access Journals (Sweden)

L. Pirozzolo

2017-07-01

Full Text Available Hot bituminous mixtures are becoming widely used in modern railway tracks in the sub-ballast layer. The reason is that these materials allow for both an increase in bearing capacity and greater protection of the substructure respect the traditional granular sub-ballast. Despite these advantages, the fact that these materials are manufactured at a temperature of 160°C means that their application can lead to an important increase in construction costs, pollution and energy consumption. This paper aims to study the possibility of using WMA manufactured at lower temperatures, as bituminous sub-ballast, in order to save energy and reduce emissions throughout the production process, as well as diminish the global costs of this layer. To this end, this study focuses on a comparison of the mechanical behaviour of warm and hot bituminous mixtures as sub-ballast under various loading conditions. The results indicate that WMA offers mechanical behaviour that is comparable to conventional HMA.

Operational efficiency of ballast water biocides at low water temperatures

NARCIS (Netherlands)

Kaag, N.H.B.M.; Sneekes, A.C.

2015-01-01

In the period 2013-2015 the effect of two biocides used for the treatment of ballast water has been evaluated at low ambient temperatures. Peraclean® Ocean and sodium hypochlorite were used as biocides. Most of the tests were conducted during winter and early spring at the laboratories of IMARES in

Toxicity evaluation of ballast water discharged at The Onne Port ...

African Journals Online (AJOL)

The discharge of these ballast water poses a major environmental threat to the water quality and Port infrastructures at the Onne Port complex as contaminants may find their way into the food chain/food web and bioaccumulate in the tissues of indigenous biota (microorganisms, crabs, mangrove oysters and fin-fishes).

The ships' ballast water impact on the Black Sea marine environment

Science.gov (United States)

Acomi, Nicoleta; Acomi, Ovidiu

2015-04-01

Ships use ballast water to provide stability during voyages. This type of seawater loaded on board from one geographical area and discharged in very different port areas as ballasting practice, turned into a vector for spreading the non-native sea life species. The reduction and limitation of invasive species is a problem that the modern world addresses. Thus, the International Maritime Organization (IMO) developed the BWM 2004 Convention. Adopting international regulations influences the socio-economic sector and this is the reason why the ballast water, the subject of this paper, has been on the IMO Marine Environment Protection Committee's agenda for more than 10 years, while the Convention has not yet been ratified and enforced. Although the Black Sea was subject to incidents regarding the invasive species the Romanian Government, as member of the IMO, did not ratify the Convention. The Black Sea was the subject of four major incidents regarding the ships' ballast water. One of them refers to the North American Comb Jelly, native from the Eastern Seaboard of America, introduced in the Black, Azov and Caspian Seas and seriously affecting the Romanian coastal environment in the 1990's. This invasive species has negative impacts: it reproduces rapidly under favourable conditions, it feeds excessively on zooplankton, it depletes zooplankton stocks, altering the food web and the ecosystem functionality, and contributed significantly to the collapse of Black and Azov Sea fisheries in the 1990s, with massive economic and social impact. There are studies for identifying the invasive species for the Black sea, structured in a database for marine species - the Black Sea Red Data Book. For these invasive species, there have been identified and developed charts to emphasize their ways of migration into the Black Sea. This paper aims to analyse the marine traffic in Romanian ports, broken down according with seasons and types of vessels, and to assess its relationship with

A New Cross-Shaped Graphite Furnace with Ballast Body for Reduction of Interferences in Atomic Absorption Spectrometry

Directory of Open Access Journals (Sweden)

A. A. Asweisi

2010-01-01

Full Text Available A new crossed graphite furnace for atomic absorption spectrometry (GFAAS was designed and installed in heated graphite atomizer (HGA500 combined with Perkin-Elmer spectrometer (AAS1100. The Tungsten ballast body was inserted inside one part of the crossed furnace in a way perpendicular to light path. The analyzed sample was injected manually on the ballast body inside the cross and pushed into the measuring zone using the original inner and additional purge gas. The sample was adsorbed strongly on the ballast and evaporated and transferred with different rates at different temperatures during the temperature program allowing the separation of analyte and matrix signals. Analysis of middle volatile element such as copper and manganese in standard urine sample (seronorm 2525 showed complete separation of analyte and background signals with good sensitivity and repeatability.

Time and concentration dependency in the potentially affected fraction of species: the case of hydrogen peroxide treatment of ballast water

NARCIS (Netherlands)

Smit, M.G.D.; Ebbens, E.; Jak, R.G.; Huijbregts, M.J.A.

2008-01-01

Transport of large volumes of ballast water contributes greatly to invasions of species. Hydrogen peroxide (H2O2) can be used as a disinfectant to prevent the spread of exotic species via ballast water. Instead of using environmental risk assessment techniques for protecting a certain fraction of

Ballast Water Treatment, U.S. Great Lakes Bulk Carrier Engineering and Cost Study. Volume 1: Present Conditions

Science.gov (United States)

2013-11-01

There are two U.S. cement plants (Charlevoix and Alpena ) that supply all U.S. ports on the lakes. Ballast Water Treatment, U.S. Great Lakes...Marquette, MI Brevort, MI Buffington, IN Alpena , MI Bay City, MI Cleveland, OH Ashtabula, OH Duluth, MN Munising, MI Charlevoix, MI Burns Harbor, IN...Manitowoc Pathfinder Calumet Alpena Total shown: 40,699,415 mt Total, all U.S. Vsls: 42,508,108 mt % ballast moved by top 5 vsls

Assessing ballast treatment standards for effect on rate of establishment using a stochastic model of the green crab

Directory of Open Access Journals (Sweden)

Cynthia Cooper

2012-03-01

Full Text Available This paper describes a stochastic model used to characterize the probability/risk of NIS establishment from ships' ballast water discharges. Establishment is defined as the existence of a sufficient number of individuals of a species to provide for a sustained population of the organism. The inherent variability in population dynamics of organisms in their native or established environments is generally difficult to quantify. Muchqualitative information is known about organism life cycles and biotic and abiotic environmental pressures on the population, but generally little quantitative data exist to develop a mechanistic model of populations in such complex environments. Moreover, there is little quantitative data to characterize the stochastic fluctuations of population size over time even without accounting for systematic responses to biotic and abiotic pressures. This research applies an approach using life-stage density and fecundity measures reported in research to determine a stochastic model of an organism's population dynamics. The model is illustrated withdata from research studies on the green crab that span a range of habitats of the established organism and were collected over some years to represent a range of time-varying biotic and abiotic conditions that are expected to exist in many receiving environments. This model is applied to introductions of NIS at the IMO D-2 and the U.S. ballast water discharge standard levels designated as Phase Two in the United States Coast Guard'sNotice of Proposed Rulemaking. Under a representative range of ballast volumes discharged at U.S. ports, the average rate of establishment of green crabs for ballast waters treated to the IMO-D2 concentration standard (less than 10 organisms/m3 is predicted to be reduced to about a third the average rate from untreated ballast water discharge. The longevity of populations from the untreated ballast water discharges is expected to be reducedby about 90% by

THE PRECAUTIONARY PROCEDURES IN THE CASE OF NON-COMPLIANCE WITH THE BALLAST WATER MANAGEMENT CON-VENTION’S STANDARDS – POSSIBLE SOLUTIONS FOR POLISH PORTS

Directory of Open Access Journals (Sweden)

Magdalena Klopott

2016-12-01

Full Text Available On September 8, 2017 the International Convention for the Control and Manage-ment of Ships’ Ballast Water and Sediments (BWMC adopted in 2004 will enter into force. It imposes a lot of requirements on shipowners and port states. The aim of this article is to elaborate on the possible solutions that may be adopted in Polish ports as precau-tionary measures in the case of non-compliance with the provisions of BWMC. The article starts with a brief overview of BWMC and ballast water quality stand-ards. Further, it discusses the possible implications of not meeting the ballast water quality standards under BWMC. The elaboration of potential solutions and mitigation measures in the event of non-compliance with the BWMC constitutes the main part of the article. These are crucial to developing a port contingency plan and include, for example, shore-based reception facility for ballast water, mobile ballast water treatment systems, and using potable water. The article ends with a brief analysis of a possible fee systems for reception of ballast water. The research was based on a comprehensive analysis of the Convention and related legal documents, interviews with ports’ representatives as well as e-mail interviews with maritime authorities in the Baltic Sea countries.

Fate of Enteromorpha flexuosa (Wulfen) J. Agardh and its spores in darkness: Implications for ballast water management

Digital Repository Service at National Institute of Oceanography (India)

Kolwalkar, J.P.; Sawant, S.S.; Dhargalkar, V.K.

of Enteromorpha flexuosa (Wulfen) J. Agardh and its spores in darkness: Implications for ballast water management Janhavi P. Kolwalkar, Subhash S. Sawant* and Vinod K. Dhargalkar National Institute of Oceanography, Dona Paula, Goa. 403004 ? India... is controlled by natural events. However, once in the dark ballast tanks, their ambient environment is altered. The information on the fate of such organisms during extended incubation in dark and their potential to thrive in new environment is of great...

Recolonization by heterotrophic bacteria after UV irradiation or ozonation of seawater; a simulation of ballast water treatment.

Science.gov (United States)

Hess-Erga, Ole-Kristian; Blomvågnes-Bakke, Bente; Vadstein, Olav

2010-10-01

Transport of ballast water with ships represents a risk for introduction of foreign species. If ballast water is treated during uptake, there will be a recolonization of the ballast water by heterotrophic bacteria during transport. We investigated survival and succession of heterotrophic bacteria after disinfection of seawater in the laboratory, representing a model system of ballast water treatment and transport. The seawater was exposed to ultraviolet (UV) irradiation, ozone (2 doses) or no treatment, incubated for 16 days and examined with culture-dependent and -independent methods. The number of colony-forming units (CFU) was reduced below the detection level after disinfection with UV and high ozone dose (700 mV), and 1% of the initial level for the low ozone dose (400 mV). After less than 3 days, the CFU was back or above the starting point for the control, UV and low ozone treatment, whereas it took slightly more than 6 days for the high ozone treatment. Disinfection increased substrate availability and reduced cell densities. Lack of competition and predation induced the recolonization by opportunistic bacteria (r-strategists), with significant increase in bacterial numbers and a low diversity (based on DGGE band pattern). All cultures stabilized after the initial recolonization phase (except Oz700) where competition due to crowding and nutrient limitation favoured bacteria with high substrate affinity (K-strategists), resulting in higher species richness and diversity (based on DGGE band pattern). The bacterial community was significantly altered qualitatively and quantitatively and may have a higher potential as invaders in the recipient depending on disinfection method and the time of release. These results have implications for the treatment strategy used for ballast water. Copyright © 2010 Elsevier Ltd. All rights reserved.

Application of ion torrent sequencing to the assessment of the effect of alkali ballast water treatment on microbial community diversity.

Science.gov (United States)

Fujimoto, Masanori; Moyerbrailean, Gregory A; Noman, Sifat; Gizicki, Jason P; Ram, Michal L; Green, Phyllis A; Ram, Jeffrey L

2014-01-01

The impact of NaOH as a ballast water treatment (BWT) on microbial community diversity was assessed using the 16S rRNA gene based Ion Torrent sequencing with its new 400 base chemistry. Ballast water samples from a Great Lakes ship were collected from the intake and discharge of both control and NaOH (pH 12) treated tanks and were analyzed in duplicates. One set of duplicates was treated with the membrane-impermeable DNA cross-linking reagent propidium mono-azide (PMA) prior to PCR amplification to differentiate between live and dead microorganisms. Ion Torrent sequencing generated nearly 580,000 reads for 31 bar-coded samples and revealed alterations of the microbial community structure in ballast water that had been treated with NaOH. Rarefaction analysis of the Ion Torrent sequencing data showed that BWT using NaOH significantly decreased microbial community diversity relative to control discharge (pPCoA) plots and UPGMA tree analysis revealed that NaOH-treated ballast water microbial communities differed from both intake communities and control discharge communities. After NaOH treatment, bacteria from the genus Alishewanella became dominant in the NaOH-treated samples, accounting for microbial community structure between PMA-processed and non-PMA samples occurred in intake water samples, which exhibited a significantly higher amount of PMA-sensitive cyanobacteria/chloroplast 16S rRNA than their corresponding non-PMA total DNA samples. The community assembly obtained using Ion Torrent sequencing was comparable to that obtained from a subset of samples that were also subjected to 454 pyrosequencing. This study showed the efficacy of alkali ballast water treatment in reducing ballast water microbial diversity and demonstrated the application of new Ion Torrent sequencing techniques to microbial community studies.

Consequences of using crushed crystalline rock as ballast in KBS-3 tunnels instead of rounded quartz particles

Energy Technology Data Exchange (ETDEWEB)

Push, R [Clay Technology AB (Sweden)

1995-02-01

The basic question has been whether such replacement alters the hydraulic conductivity and compressibility as well as expandability and also if the physical and chemical stabilities are altered. The key factor is the microstructural constitution of the bentonite/ballast mixtures, which is primarily controlled by the grain size distribution of the ballast. The compact ability of backfills with quartz sand (SB) is higher than that of backfills with crushed rock as ballast (RB). The physical stability of RB backfills in terms of piping and erosion resistance will be somewhat lower than that of SB backfills. The chemical stability is practically independent of whether the ballast is pure quartz or rock with K-bearing minerals because the temperature in the backfill will be too low to yield significant smectite to illite conversion in the short heating period. In order to reach the same densities of SB and RB backfills, which turn out to give fairly similar physical properties, the latter backfills need more effective compaction or, alternatively, a higher bentonite content. It is estimated that if the bentonite content in RB backfills is not increased while the density is enhanced to what is achievable, these backfills will serve equally well as SB backfills with the densities implied by the basic KBS-3 concept. 23 refs, 27 figs, 7 tabs.

Consequences of using crushed crystalline rock as ballast in KBS-3 tunnels instead of rounded quartz particles

International Nuclear Information System (INIS)

Push, R.

1995-02-01

The basic question has been whether such replacement alters the hydraulic conductivity and compressibility as well as expandability and also if the physical and chemical stabilities are altered. The key factor is the microstructural constitution of the bentonite/ballast mixtures, which is primarily controlled by the grain size distribution of the ballast. The compact ability of backfills with quartz sand (SB) is higher than that of backfills with crushed rock as ballast (RB). The physical stability of RB backfills in terms of piping and erosion resistance will be somewhat lower than that of SB backfills. The chemical stability is practically independent of whether the ballast is pure quartz or rock with K-bearing minerals because the temperature in the backfill will be too low to yield significant smectite to illite conversion in the short heating period. In order to reach the same densities of SB and RB backfills, which turn out to give fairly similar physical properties, the latter backfills need more effective compaction or, alternatively, a higher bentonite content. It is estimated that if the bentonite content in RB backfills is not increased while the density is enhanced to what is achievable, these backfills will serve equally well as SB backfills with the densities implied by the basic KBS-3 concept. 23 refs, 27 figs, 7 tabs

The method of the atomic-absorption analysis in a graphite furnace with the metallic collector-ballast

International Nuclear Information System (INIS)

Katskov, D.A.; Vasil'eva, L.A.; Grinshtejn, I.L.; Savel'eva, G.O.

1987-01-01

New method of atomic-absorption analysis in a graphite furnace with the metallic collector-ballast (tungsten were) is suggested. It enables to widen the number of analyzed objects of liquid products wetting readily graphite and metals. It is shown that application of metallic collector-ballast enables to improve sensitivity and reproducibility of analysis, increase the volume of dosed samples as well as to suppress effectively the influence of excess of mineral and organic substrate on results of atomic-absorption analysis of several elements, including Cd, Sr, In, Te

Three-dimensional laser scanning technique to quantify aggregate and ballast shape properties

CSIR Research Space (South Africa)

Anochie-Boateng, Joseph

2013-06-01

Full Text Available methods towards a more accurate and automated techniques to quantify aggregate shape properties. This paper validates a new flakiness index equation using three-dimensional (3-D) laser scanning data of aggregate and ballast materials obtained from...

Potential use of an ultrasound antifouling technology as a ballast water treatment system

Science.gov (United States)

Estévez-Calvar, Noelia; Gambardella, Chiara; Miraglia, Francesco; Pavanello, Giovanni; Greco, Giuliano; Faimali, Marco; Garaventa, Francesca

2018-03-01

The aim of this study was to investigate, at a laboratory scale, the potentialities of an ultrasound-based treatment initially designed to eliminate fouling, as a ballast water treatment system. Therefore, early life stages of three different zooplanktonic species (Amphibalanus amphitrite, Brachionus plicatilis and Artemia salina) were exposed to ultrasound waves (20-22 kHz). The experimental set up included static assays with variations of time exposure (30 s, 60 s and 30 s on/60 s off/30 s on), material of tanks (stainless steel, galvanized steel and plastic) and position of the ultrasound source. Results showed that the treatment efficacy increased from 30 to 60 s and no differences were registered between 60 s-continuous exposure and pulse exposure. The highest efficacy was observed in Experiment I (metal-to-metal contact assay) with a mortality value of 93-95% for B. plicatilis and A. salina. It consisted of organisms located inside stainless steel tubes that were located in direct contact with the ultrasound source and treated for 60 s. Further, we found that, generally, A. amphitrite and B. plicatilis were the most resistant species to the ultrasound treatment whereas A. salina was the most sensitive. We further discuss that US may unlikely be used for commercial vessels, but may be used to treat ballast water in smaller ballast tanks as on board of mega yachts.

INVESTIGATION OF INNER SHEAR RESISTANCE OF GEOGRIDS BUILT UNDER GRANULAR PROTECTION LAYERS AND RAILWAY BALLAST

Directory of Open Access Journals (Sweden)

Sz. Fischer

2015-10-01

Full Text Available Purpose. Using adequate granular materials and layer structures in the railway super- and substructure is able to stabilise railway track geometry. For this purpose special behaviour of above materials has to be determined, e.g. inner shear resistance. Inner shear resistance of granular media with and without geogrid reinforcement in different depths is not known yet. Methodology. The author developed a special laboratory method to measure and define inner shear resistance of granular materials, it is called «multi-level shear box test». This method is adequate to determine inner shear resistance (pushing force vs. depth (distance from the «zero» surface. Two different granular materials: andesite railway ballast (31.5/63 mm and andesite railway protection layer material (0/56 mm, and seven different types of geogrids (GG1…GG7 were used during the tests. Findings. Values of inner shear resistance functions of andesite railway ballast without geogrid reinforcement and reinforced with different types of geogrids and andesite granular protection layer in function of the vertical distance from the geogrid plane were determined with multi-layer shear box tests when the material aggregation is uncompacted and compacted. Only the compacted sample was tested in case of the 0/56 mm protection layer. Cubic polynomial regression functions fitted on the mean values of the measurements are described graphically. Determination coefficients with values of R2>0.97 were resulted in all the cases of regression functions. Based on the polynomial regression functions fitted on the mean values of the test results, three increasing factors were determined in function of the distance measured from the geogrid. Increasing factor «A», «B» and «D». Originality. Multi-level shear box test, developed by the author, is certified unequivocally adequate for determining inner shear resistance of reinforced and unreinforced granular materials, e.g. railway ballast

A method for handlebars ballast calculation in order to reduce vibrations transmissibility in walk behind tractors

Directory of Open Access Journals (Sweden)

Angelo Fabbri

2017-06-01

Full Text Available Walk behind tractors have some advantages over other agricultural machines, such as the cheapness and the easy to use, however the driver is exposed to high level of vibrations transmitted from handles to hand-arm system and to shoulders. The vibrations induce discomfort and early fatigue to the operator. In order to control the vibration transmissibility, a ballast mass may be added to the handles. Even if the determination of the appropriate ballast mass is a critical point in the handle design. The aim of this research was to study the influence of the handle mass modification, on the dynamic structure behaviour. Modal frequencies and subsequent transmissibility calculated by using an analytical approach and a finite elements model, were compared. A good agreement between the results obtained by the two methods was found (average percentage difference calculated on natural frequencies equal to 5.8±3.8%. Power tillers are made generally by small or medium-small size manufacturers that have difficulties in dealing with finite element codes or modal analysis techniques. As a consequence, the proposed analytical method could be used to find the optimal ballast mass in a simple and economic way, without experimental tests or complex finite element codes. A specific and very simple software or spreadsheet, developed on the base of the analytical method here discussed, could effectively to help the manufacturers in the handlebar design phase. The choice of the correct elastic mount, the dimensioning of the guide members and the ballast mass could be considerably simplified.

Guidance for a harmonized emission scenario document (ESD) on ballast water discharge

Energy Technology Data Exchange (ETDEWEB)

Zipperle, Andreas [BIS - Beratungszentrum fuer integriertes Sedimentmanagement, Hamburg (Germany); Gils, Jos van [DELTARES, Delft (Netherlands); Hattum, Bert van [Amsterdam Univ. (Netherlands). IVM - Institute for Environmental Studies; Heise, Susanne [BIS - Beratungszentrum fuer integriertes Sedimentmanagement, Hamburg (Germany); Hamburg Univ. of Applied Sciences (Germany)

2011-05-15

The present report provides guidance for a harmonized Emission Scenario Document (ESD) for the exposure assessment as part of the environmental risk assessment process which applicants seeking approval of a ballast water management system (BWMS) need to perform prior to notification and authorisation procedures. Despite the global variability of the marine environment, ballast water discharges and treatment methods, exposure assessments need to be comparable between different applications. In order to achieve this, this ESD points out the following aspects: - Applicants should use standardized scenarios in order to predict mean exposure. These should reflect generic situations, independent of region or port so that results are widely applicable. In addition to a harbour scenario, a standardized shipping lane scenario should be considered, - During or right after ballast water discharge, high concentrations may persist in a water body for a certain length of time until extensive mixing results in mean concentrations. Not taking exposure to peak concentrations within gradients into account could lead to an underestimation of risk, especially for rapidly degrading substances. Efforts have been made to approximate maximum exposure concentration with simple dilution factors. Their applicability was checked by near-field-evaluations. - Chemical properties determine the environmental fate of substances. If they are ambiguous, selection of a specific set of data strongly influences the result of an exposure assessment. Guidance is given on what to do about lacking data. - In order to harmonize the exposure assessments, reliable chemical model software should be used. A discussion on the requirements of suitable software and an evaluation of MAMPEC is given in this report. (orig.)

Rapid molecular detection of invasive species in ballast and harbor water by integrating environmental DNA and light transmission spectroscopy.

Science.gov (United States)

Egan, Scott P; Grey, Erin; Olds, Brett; Feder, Jeffery L; Ruggiero, Steven T; Tanner, Carol E; Lodge, David M

2015-04-07

Invasive species introduced via the ballast water of commercial ships cause enormous environmental and economic damage worldwide. Accurate monitoring for these often microscopic and morphologically indistinguishable species is challenging but critical for mitigating damages. We apply eDNA sampling, which involves the filtering and subsequent DNA extraction of microscopic bits of tissue suspended in water, to ballast and harbor water sampled during a commercial ship's 1400 km voyage through the North American Great Lakes. Using a lab-based gel electrophoresis assay and a rapid, field-ready light transmission spectroscopy (LTS) assay, we test for the presence of two invasive species: quagga (Dreissena bugensis) and zebra (D. polymorpha) mussels. Furthermore, we spiked a set of uninfested ballast and harbor samples with zebra mussel tissue to further test each assay's detection capabilities. In unmanipulated samples, zebra mussel was not detected, while quagga mussel was detected in all samples at a rate of 85% for the gel assay and 100% for the LTS assay. In the spiked experimental samples, both assays detected zebra mussel in 94% of spiked samples and 0% of negative controls. Overall, these results demonstrate that eDNA sampling is effective for monitoring ballast-mediated invasions and that LTS has the potential for rapid, field-based detection.

The Brazilian dilution method for ballast water exchange; O metodo de diluicao brasileiro para troca de agua de lastro

Energy Technology Data Exchange (ETDEWEB)

Mauro, Celso Alleluia [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas. Avaliacao e Monitoramento Ambiental]. E-mail: celso@cenpes.petrobras.com.br; Land, Claudio Goncalves [PETROBRAS, Rio de Janeiro, RJ (Brazil). Abastecimento, Logistica e Planejamento]. E-mail: cgland@petrobras.com.br; Pimenta, Jose Maria Hollanda Alvares; Barreto, Francisco Carlos Peixoto [PETROBRAS, Rio de Janeiro, RJ (Brazil). Engenharia; Brandao, Marcus Vinicius Lisboa; Marroig, Nilton Lemos [Transpetro, Rio de Janeiro, RJ (Brazil). Frota Nacional de Petroleiros. Inspetoria Geral; Tristao, Maria Luiza Braganca [PETROBRAS, Rio de Janeiro, RJ (Brazil). Centro de Pesquisas. Quimica; Fadel, Andre Luiz da Fonseca [PETROBRAS, Rio de Janeiro, RJ (Brazil). Financas Corporativa e Tesouraria; Villac, Maria Celia; Fernandes, Lohengrin; Paranhos, Rodolfo; Dias, Cristina; Bonecker, Sergio; Denise Tenenbaum [Universidade Federal, Rio de Janeiro, RJ (Brazil). Inst. de Biologia; Persich, Graziela; Garcia, Virginia; Odebrecht, Clarisse [Fundacao Universidade do Rio Grande, RS (Brazil). Dept. de Oceanografia

2002-12-01

In a precautionary approach and dealing with the coming International Maritime Organization (IMO) regulations on ballast water, PETROBRAS developed a new method for ballast water exchange in tankers. Differently from ordinary methods PETROBRAS method which have been called Brazilian Dilution Method (BDM) or Dilution Method involves ballast loading through the top with simultaneous unloading from the bottom of the tanks. The method proposal was firstly presented to IMO, which encouraged PETROBRAS to carry out a field trial. PETROBRAS in June 1998 carried out a trial in the product carrier M/V Lavras. A simulation study was useful to plan the trial assessing the theoretical efficiency of the method, establishing the best sampling points and comparing the BDM with the Tank Overfilling Method (TOM). Simulation showed that for the same tank shape, the water renewal in BDM is more effective than in TOM and that 90 % of water renewal could be obtained by BDM. A dye concentration variation monitoring and a biological assessment were performed and the results confirmed that over than 90 % of the ballast water was renewed after three exchanges. The method was proved safe, practical, economical and suitable to minimize the risk of exotic species transport between ports. (author)

Pandemic serotypes of Vibrio cholerae isolated from ships' ballast tanks and coastal waters: assessment of antibiotic resistance and virulence genes (tcpA and ctxA).

Science.gov (United States)

Dobbs, Fred C; Goodrich, Amanda L; Thomson, Frank K; Hynes, Wayne

2013-05-01

There is concern that ships' ballasting operations may disseminate Vibrio cholerae to ports throughout the world. Given evidence that the bacterium is indeed transported by ships, we isolated pandemic serotypes O1 and O139 from ballast tanks and characterized them with respect to antibiotic resistance and virulence genes ctxA and tcpA. We carried out concurrent studies with V. cholerae isolated from coastal waters. Of 284 isolates, 30 were serotype O1 and 59 were serotype O139. These serotypes were overrepresented in ballast tanks relative to the coastal waters sampled. All locations, whether coastal waters or ballast tanks, yielded samples from which serotype O1, O139, or both were isolated. There were three groups among the 62 isolates for which antibiotic characterization was conclusive: those exhibiting β-lactamase activity and resistance to at least one of the 12 antibiotics tested; those negative for β-lactamase but having antibiotic resistance; those negative for β-lactamase and registering no antibiotic resistance. When present, antibiotic resistance in nearly all cases was to ampicillin; resistance to multiple antibiotics was uncommon. PCR assays revealed that none of the isolates contained the ctxA gene and only two isolates, one O139 and one O1, contained the tcpA gene; both isolates originated from ballast water. These results support the bacteriological regulations proposed by the International Maritime Association for discharged ballast water.

Application of ion torrent sequencing to the assessment of the effect of alkali ballast water treatment on microbial community diversity.

Directory of Open Access Journals (Sweden)

Masanori Fujimoto

Full Text Available The impact of NaOH as a ballast water treatment (BWT on microbial community diversity was assessed using the 16S rRNA gene based Ion Torrent sequencing with its new 400 base chemistry. Ballast water samples from a Great Lakes ship were collected from the intake and discharge of both control and NaOH (pH 12 treated tanks and were analyzed in duplicates. One set of duplicates was treated with the membrane-impermeable DNA cross-linking reagent propidium mono-azide (PMA prior to PCR amplification to differentiate between live and dead microorganisms. Ion Torrent sequencing generated nearly 580,000 reads for 31 bar-coded samples and revealed alterations of the microbial community structure in ballast water that had been treated with NaOH. Rarefaction analysis of the Ion Torrent sequencing data showed that BWT using NaOH significantly decreased microbial community diversity relative to control discharge (p<0.001. UniFrac distance based principal coordinate analysis (PCoA plots and UPGMA tree analysis revealed that NaOH-treated ballast water microbial communities differed from both intake communities and control discharge communities. After NaOH treatment, bacteria from the genus Alishewanella became dominant in the NaOH-treated samples, accounting for <0.5% of the total reads in intake samples but more than 50% of the reads in the treated discharge samples. The only apparent difference in microbial community structure between PMA-processed and non-PMA samples occurred in intake water samples, which exhibited a significantly higher amount of PMA-sensitive cyanobacteria/chloroplast 16S rRNA than their corresponding non-PMA total DNA samples. The community assembly obtained using Ion Torrent sequencing was comparable to that obtained from a subset of samples that were also subjected to 454 pyrosequencing. This study showed the efficacy of alkali ballast water treatment in reducing ballast water microbial diversity and demonstrated the application of new

76 FR 25211 - Energy Conservation Program: Test Procedures for Fluorescent Lamp Ballasts

Science.gov (United States)

2011-05-04

...-government procurement policies that specify high efficiency ballasts. (CA IOUs, No. 19 at p. 2; NRDC, No. 21... luminous efficiency (BLE), which is measured directly using electrical measurements instead of the photometric measurements employed in the test procedure at Appendix Q. The calculation of BLE includes a...

Ballasting pipeline moving in horizontal well as method of control sticking phenomenon

Science.gov (United States)

Toropov, V. S.; Toropov, E. S.

2018-05-01

The mechanism of the phenomenon of sticking a pipeline moving in a well while pulled by the facility horizontal directional drilling is investigated. A quantitative evaluation of the force arising from sticking is given. At the same time, the working hypothesis takes a view of the combined effect of adhesion and friction interactions as the reasons that cause this phenomenon. As a measure to control the occurrence of sticking and to reduce the resistance force to movement of the pipeline in the well, several methods of ballasting the working pipeline are proposed, depending on the profile of the well and the ratio of the length of the curved sections of the inlet and outlet and the straight horizontal sections of the profile. It is shown that for crossings, which profile contains an extended horizontal section, it is possible to partially fill the pipeline with water to achieve zero buoyancy, and for crossings with curvature along the entire profile, the ballasting efficiency will be minimal.

Global ballast water management and the "same location" concept: a clear term or a clear issue?

Science.gov (United States)

David, Matej; Gollasch, Stephan; Pavliha, Marko

2013-03-01

The United Nations recognized the transfer of harmful organisms and pathogens across natural barriers as one of the four greatest pressures to the world's oceans and seas, causing global environmental changes, while also posing a threat to human health, property, and resources. Ballast water transferred by vessels was recognized as a prominent vector of such species and was regulated by the International Convention for the Control and Management of Ship's Ballast Water and Sediments (2004). Permanent exceptions from ballast water management requirements may apply when the uptake and discharge of ballast water occur at the "same location." However, the "same location" concept may be interpreted differently, e.g., a port basin, a port, an anchorage, or a larger area even with more ports inside. Considering that the Convention is nearing the beginning of enforcement, national authorities all around the world will soon be exposed to applications for exceptions. Here we consider possible effects of different interpretations of the "same location" concept. We have considered different possible extensions of the same location through environmental, shipping, and legal aspects. The extension of such areas, and the inclusion of more ports, may compromise the Convention's main purpose. We recommend that "same location" mean the smallest practicable unit, i.e., the same harbor, mooring, or anchorage. An entire smaller port, possibly also including the anchorage, could be considered as same location. For larger ports with a gradient of environmental conditions, "same location" should mean a terminal or a port basin. We further recommend that IMO consider the preparation of a guidance document to include concepts, criteria, and processes outlining how to identify "same location," which limits should be clearly identified.

Developing and testing an Early Warning System for Non Indigenous Species and Ballast Water Management

Science.gov (United States)

Magaletti, Erika; Garaventa, Francesca; David, Matej; Castriota, Luca; Kraus, Romina; Luna, Gian Marco; Silvestri, Cecilia; Forte, Cosmo; Bastianini, Mauro; Falautano, Manuela; Maggio, Teresa; Rak, Giulietta; Gollasch, Stephan

2018-03-01

This paper describes the methodological approach used for the development of an Early Warning System (EWS) for Non Indigenous Species (NIS) and ballast water management and summarizes the results obtained. The specific goals of the EWS are firstly to warn vessels to prevent loading of ballast water when critical biological conditions occur in ports and surrounding areas i.e. mass development or blooms of Harmful Aquatic Organisms and Pathogens (HAOP). Secondly, to warn environmental and health authorities when NIS or pathogens are present in ports or surrounding areas to enable an early response and an implementation of remediation measures. The EWS is designed to be used for implementing various parallel obligations, by taking into consideration different legal scopes, associated information and decision-making needs. The EWS was elaborated, tested in the Adriatic Sea and illustrated by two case studies. Although the EWS was developed with an Adriatic Sea focus, it is presented in a format so that it may be used as a model when establishing similar systems in other locations. The role of the various actors is discussed and recommendations on further developments of the EWS are presented. It was concluded that the EWS is a suitable tool to reduce the spread of potentially harmful and ballast water mediated species.

Optimization of hydrocyclone geometry for ballast water treatment of crude oil ships; Otimizacao da geometria de hidrociclones para o tratamento de aguas de lastro de navios petroleiros

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Andre G.; Medronho, Ricardo A. [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Escola de Quimica

2004-07-01

An oil ship when discharge its load, pumps water of the sea for its ballast tanks. This water has the function of maintaining balance, stability and the structural integrity, especially when the oil tank is empty of cargo. Thus, organisms and sediments presents in the water are pumped for the interior of the ballast tanks, being transferred from its natural habitat to another one. This may cause serious ecological unbalances. Hydrocyclone are very efficient and, as they produce high capacities, they seem to be appropriated for ballast water treatment. In this work, computational fluid dynamics (CFD) was used to optimize the geometry of a hydrocyclone, aiming to maximize the separation of the suspended solids present in seawater. A oil ship of 150,000 tons of gross cargo was used as a model. This ship has a ballast capacity of 45,000 m{sup 3} and requires 10 h for filling its ballast tanks. To ballast this ship it would be necessary a battery of 795 hydrocyclones in parallel, having each hydrocyclone a diameter of 8,5 cm. The simulation produced an total efficiency of 99% when treating suspended solids with sizes ranging from 10 to 2500 {mu}m, with a 1.06 g cm-3 density. (author)

Developing Molecular Methods to Identify and Quantify Ballast Water Organisms: A Test Case with Cnidarians

National Research Council Canada - National Science Library

Kreiser, Brian R

2004-01-01

.... Furthermore, biological invasions mediated by ballast water transport have led to some rather severe economic and ecological consequences as seen in the examples of the zebra mussel and green crab...

76 FR 70547 - Energy Conservation Program: Energy Conservation Standards for Fluorescent Lamp Ballasts

Science.gov (United States)

2011-11-14

... the term ``fluorescent lamp,'' which EPCA defines as ``a low pressure mercury electric-discharge... discharge into light,'' and as including the four enumerated types of fluorescent lamps for which EPCA... Conservation Program: Energy Conservation Standards for Fluorescent Lamp Ballasts; Final Rule #0;#0;Federal...

Bitumen stabilized ballast: a potential solution for railway track-bed

OpenAIRE

D'Angelo, Giacomo; Thom, Nicholas; Lo Presti, Davide

2016-01-01

Railway ballast degradation under dynamic loads progressively leads to loss of mechanical performance and geometry of the track, so that maintenance interventions are frequently needed. In order to systematically avoid this issue, recently solutions have been proposed to reinforce track-bed by using polyurethane and/or resins as well as asphalt layers among others. Nonetheless, their main limitations are related to the high initial cost and low productivity.\\ud To cope with these limitations,...

Dynamic modelling of high speed ballasted railway trakcs: Analysis of the behaviour

Energy Technology Data Exchange (ETDEWEB)

Gallego, I.; Rivas, A.; Sanchez-Cambronero, S.; Lajara, J.

2016-07-01

The aim of the paper is to present a numerical model for a ballasted railway track that includes the dynamic effect of a moving train load and predicts the values of the vertical stiffness of the infrastructure. This model is therefore deemed to be a tool for the evaluation of the state of the track during service situations as well as a predictive model of the behaviour of the system. Consequently, it will be very useful when sizing the cross section of a new railway line is required.The main modelling tool is the finite element method. In regard to this, the application of damping elements to avoid the elastic wave reflection on the boundaries of the numerical domain will be studied. The proposed dynamic analysis consider the change in time of the value of the train load, but not the change in position along the tracks.In the end, a set of suggestions for the numerical model with moving loads will be summarize aiming for the mitigation of the unusual behaviour of the contact surface between the ballast and the sleepers. (Author)

Development of Viscoelastic Multi-Body Simulation and Impact Response Analysis of a Ballasted Railway Track under Cyclic Loading

Directory of Open Access Journals (Sweden)

Daisuke Nishiura

2017-06-01

Full Text Available Simulation of a large number of deformable bodies is often difficult because complex high-level modeling is required to address both multi-body contact and viscoelastic deformation. This necessitates the combined use of a discrete element method (DEM and a finite element method (FEM. In this study, a quadruple discrete element method (QDEM was developed for dynamic analysis of viscoelastic materials using a simpler algorithm compared to the standard FEM. QDEM easily incorporates the contact algorithm used in DEM. As the first step toward multi-body simulation, the fundamental performance of QDEM was investigated for viscoelastic analysis. The amplitude and frequency of cantilever elastic vibration were nearly equal to those obtained by the standard FEM. A comparison of creep recovery tests with an analytical solution showed good agreement between them. In addition, good correlation between the attenuation degree and the real physical viscosity was confirmed for viscoelastic vibration analysis. Therefore, the high accuracy of QDEM in the fundamental analysis of infinitesimal viscoelastic deformations was verified. Finally, the impact response of a ballast and sleeper under cyclic loading on a railway track was analyzed using QDEM as an application of deformable multi-body dynamics. The results showed that the vibration of the ballasted track was qualitatively in good agreement with the actual measurements. Moreover, the ballast layer with high friction reduced the ballasted track deterioration. This study suggests that QDEM, as an alternative to DEM and FEM, can provide deeper insights into the contact dynamics of a large number of deformable bodies.

Hot impact densification (HID) - a new method of producing ceramic nuclear fuel pellets with tight dimensional tolerances

International Nuclear Information System (INIS)

Hrovat, M.; Rachor, L.; Muehling, G.; Vollath, D.; Zimmermann, H.

1984-01-01

The hot impact densification (HID) is a new powerful method for producing ceramic fuel pellets for nuclear reactors. Green ceramic bodies are directly processed to pellets by high speed shaping in the plastic temperature region of ceramic material. Opposed to the well established press sintering procedure it can be heated, densified, and cooled by orders of magnitude faster. Therefore, at high throughputs, small equipment dimensions become possible. The fuel pellets produced meet all requirements, particular the dimensional tolerances achieved are very closed, consequently circular grinding is omitted. Furthermore, the relatively high temperature level of the impact pressing favors the mixed crystal formation of uranium and plutonium oxide. This improves the solubility of the fuel in nitric acid, an essential point at reprocessing. A prototype facility is designed so that automatic fabrication in continuous operation will be possible. The target working cycle for a fuel pellet is in the range of some seconds. (orig.)

Bromination of Marine Dissolved Organic Matter following Full Scale Electrochemical Ballast Water Disinfection.

Science.gov (United States)

Gonsior, Michael; Mitchelmore, Carys; Heyes, Andrew; Harir, Mourad; Richardson, Susan D; Petty, William Tyler; Wright, David A; Schmitt-Kopplin, Philippe

2015-08-04

An extensively diverse array of brominated disinfection byproducts (DBPs) were generated following electrochemical disinfection of natural coastal/estuarine water, which is one of the main treatment methods currently under consideration for ballast water treatment. Ultra-high-resolution mass spectrometry revealed 462 distinct brominated DBPs at a relative abundance in the mass spectra of more than 1%. A brominated DBP with a relative abundance of almost 22% was identified as 2,2,4-tribromo-5-hydroxy-4-cyclopentene-1,3-dione, which is an analogue to several previously described 2,2,4-trihalo-5-hydroxy-4-cyclopentene-1,3-diones in drinking water. Several other brominated molecular formulas matched those of other known brominated DBPs, such as dibromomethane, which could be generated by decarboxylation of dibromoacetic acid during ionization, dibromophenol, dibromopropanoic acid, dibromobutanoic acid, bromohydroxybenzoic acid, bromophenylacetic acid, bromooxopentenoic acid, and dibromopentenedioic acid. Via comparison to previously described chlorine-containing analogues, bromophenylacetic acid, dibromooxopentenoic acid, and dibromopentenedioic acid were also identified. A novel compound at a 4% relative abundance was identified as tribromoethenesulfonate. This compound has not been previously described as a DBP, and its core structure of tribromoethene has been demonstrated to show toxicological implications. Here we show that electrochemical disinfection, suggested as a candidate for successful ballast water treatment, caused considerable production of some previously characterized DBPs in addition to novel brominated DBPs, although several hundred compounds remain structurally uncharacterized. Our results clearly demonstrate that electrochemical and potentially direct chlorination of ballast water in estuarine and marine systems should be approached with caution and the concentrations, fate, and toxicity of DBP need to be further characterized.

Use of rubber shreds to enhance attenuation of railway sub-ballast layers made of unbound aggregates

Directory of Open Access Journals (Sweden)

C. Hidalgo-Signes

2017-02-01

Full Text Available One of the approaches for solving the problem of induced vibrations in railways is by slightly modifying the materials that form the track. A study is presented of the attenuation capacity of mixes composed of granular soil and rubber shreds when used as sub-ballast (the layer located immediately below the ballast layer. Rubber shreds are obtained from scrap tyres, a troublesome waste material whose reuse and recycling is necessary. A series of mixes of granular soil and rubber shreds with rubber contents of between 1% and 10% are submitted to hammer impact tests to study their response to dynamic excitation. Results reveal that mixing rubber shreds with granular soil increases damping ratios, thus demonstrating the potential of the proposed mixes for attenuating vibration.

Use of rubber shreds to enhance attenuation of railway sub-ballast layers made of unbound aggregates

International Nuclear Information System (INIS)

Hidalgo-Signes, C.; Garzón-Roca, J.; Grima-Palop, J.M.; Insa-Franco, R.

2017-01-01

One of the approaches for solving the problem of induced vibrations in railways is by slightly modifying the materials that form the track. A study is presented of the attenuation capacity of mixes composed of granular soil and rubber shreds when used as sub-ballast (the layer located immediately below the ballast layer). Rubber shreds are obtained from scrap tyres, a troublesome waste material whose reuse and recycling is necessary. A series of mixes of granular soil and rubber shreds with rubber contents of between 1% and 10% are submitted to hammer impact tests to study their response to dynamic excitation. Results reveal that mixing rubber shreds with granular soil increases damping ratios, thus demonstrating the potential of the proposed mixes for attenuating vibration. [es

The effects of chemical additives on the production of disinfection byproducts and ecotoxicity in simulated ballast water

Science.gov (United States)

Park, Chul; Cha, Hyung-Gon; Lee, Ji-Hyun; Choi, Tae Seop; Lee, Jungsuk; Kim, Young-Hee; Bae, Minjung; Shin, Kyoungsoon; Choi, Keun-Hyung

2017-11-01

The management of ship ballast water is essential to stemming the introduction of non-indigenous species. Approval for onboard installation of a system to treat ballast water requires rigorous land-based testing as dictated in the G8 guideline by the International Maritime Organization. However, this testing lacks standardization-most notably augmentation of organic carbon for influent water by adding chemical additives. Electrochlorination is a popular treatment method for ballast water, in which chlorinated oxidants react with organisms and organic matter in water. The additives could thus affect the treatment efficacy of the ballast water. Here, we examined the effects of several candidates of organic carbon additives on the consumption of total residual oxidant (TRO), the production of disinfection byproducts (DBPs), plankton survival, and ecotoxicity. The TRO consumption over five days of storage was higher in electrochlorinated seawater amended with lignin and Metamucil when compared with seawaters with other organic carbon compounds. DBP production varied by almost two orders of magnitude as a function of the various additives. This was largely attributed to the production of tribromomethane and dibromoacetic acid. The survival of Artemia franciscana was significantly different across waters of different organic carbon additives. Algal toxicity testing with the marine haptophyte Isochrysis galbana significantly reduced growth in lignin- and Metamucil-treated seawaters, but not with other organic carbon compounds. Bioluminescence in Vibrio fischeri sharply declined in electrochlorinated seawaters with all types of organic carbon compounds, but no toxicity was manifested once the electrochlorinated seawaters were neutralized with sodium thiosulfate. The varying degrees of outcome suggest that it might be better to eliminate the requirements of adding organic carbon to test water as long as natural water was used for land-based testing of BWMS. If needed, the

Ballast water as a vector of coral pathogens in the Gulf of Mexico: the case of the Cayo Arcas coral reef.

Science.gov (United States)

Aguirre-Macedo, M Leopoldina; Vidal-Martinez, Victor M; Herrera-Silveira, Jorge A; Valdés-Lozano, David S; Herrera-Rodríguez, Miguel; Olvera-Novoa, Miguel A

2008-09-01

The discharge of nutrients, phytoplankton and pathogenic bacteria through ballast water may threaten the Cayo Arcas reef system. To assess this threat, the quality of ballast water and presence of coral reef pathogenic bacteria in 30 oil tankers loaded at the PEMEX Cayo Arcas crude oil terminal were determined. The water transported in the ships originated from coastal, oceanic or riverine regions. Statistical associations among quality parameters and bacteria were tested using redundancy analysis (RDA). In contrast with coastal or oceanic water, the riverine water had high concentrations of coliforms, including Vibrio cholerae 01 and, Serratia marcescens and Sphingomona spp., which are frequently associated with "white pox" and "white plague type II" coral diseases. There were also high nutrient concentrations and low water quality index values (WQI and TRIX). The presence of V. cholerae 01 highlights the need for testing ballast water coming from endemic regions into Mexican ports.

Relative invasion risk for plankton across marine and freshwater systems: examining efficacy of proposed international ballast water discharge standards.

Directory of Open Access Journals (Sweden)

Oscar Casas-Monroy

Full Text Available Understanding the implications of different management strategies is necessary to identify best conservation trajectories for ecosystems exposed to anthropogenic stressors. For example, science-based risk assessments at large scales are needed to understand efficacy of different vector management approaches aimed at preventing biological invasions associated with commercial shipping. We conducted a landscape-scale analysis to examine the relative invasion risk of ballast water discharges among different shipping pathways (e.g., Transoceanic, Coastal or Domestic, ecosystems (e.g., freshwater, brackish and marine, and timescales (annual and per discharge event under current and future management regimes. The arrival and survival potential of nonindigenous species (NIS was estimated based on directional shipping networks and their associated propagule pressure, environmental similarity between donor-recipient ecosystems (based on salinity and temperature, and effects of current and future management strategies (i.e., ballast water exchange and treatment to meet proposed international biological discharge standards. Our findings show that current requirements for ballast water exchange effectively reduce invasion risk to freshwater ecosystems but are less protective of marine ecosystems because of greater environmental mismatch between source (oceanic and recipient (freshwater ecoregions. Future requirements for ballast water treatment are expected to reduce risk of zooplankton NIS introductions across ecosystem types but are expected to be less effective in reducing risk of phytoplankton NIS. This large-scale risk assessment across heterogeneous ecosystems represents a major step towards understanding the likelihood of invasion in relation to shipping networks, the relative efficacy of different invasion management regimes and seizing opportunities to reduce the ecological and economic implications of biological invasions.

Assessment of variable fluorescence fluorometry as an approach for rapidly detecting living photoautotrophs in ballast water

Science.gov (United States)

First, Matthew R.; Robbins-Wamsley, Stephanie H.; Riley, Scott C.; Drake, Lisa A.

2018-03-01

Variable fluorescence fluorometry, an analytical approach that estimates the fluorescence yield of chlorophyll a (F0, a proximal measure of algal concentration) and photochemical yield (FV/FM, an indicator of the physiological status of algae) was evaluated as a means to rapidly assess photoautotrophs. Specifically, it was used to gauge the efficacy of ballast water treatment designed to reduce the transport and delivery of potentially invasive organisms. A phytoflagellate, Tetraselmis spp. (10-12 μm) and mixed communities of ambient protists were examined in both laboratory experiments and large-scale field trials simulating 5-d hold times in mock ballast tanks. In laboratory incubations, ambient organisms held in the dark exhibited declining F0 and FV/FM measurements relative to organisms held under lighted conditions. In field experiments, increases and decreases in F0 and FV/FM over the tank hold time corresponded to those of microscope counts of organisms in two of three trials. In the third trial, concentrations of organisms ≥ 10 and protists) increased while F0 and FV/FM decreased. Rapid and sensitive, variable fluorescence fluorometry is appropriate for detecting changes in organism concentrations and physiological status in samples dominated by microalgae. Changes in the heterotrophic community, which may become more prevalent in light-limited ballast tanks, would not be detected via variable fluorescence fluorometry, however.

Ballast system for maintaining constant pressure in a glove box

Science.gov (United States)

Shlichta, Paul J.

1989-09-01

A ballast system is disclosed for a glove box including a fixed platform on which is mounted an inflatable bag on top of which resides a cover and a weight. The variable gas volume of the inflatable bag communicates with that of the glove box via a valved tube. The weight and the gas volume are selected to maintain a relatively constant pressure in the glove box despite variations in the glove box volume while avoiding the use of complicated valving apparatus.

Electrochemical disinfection of simulated ballast water on PbO2/graphite felt electrode.

Science.gov (United States)

Chen, Shuiping; Hu, Weidong; Hong, Jianxun; Sandoe, Steve

2016-04-15

A novel PbO2/graphite felt electrode was constructed by electrochemical deposition of PbO2 on graphite felt and characterized by X-ray powder diffraction (XRD) and scanning electron microscopy (SEM) analysis. The prepared electrode is a viable technology for inactivation of Escherichia coli, Enterococcus faecalis, and Artemia salina as indicator organisms in simulated ballast water treatment, which meets the International Maritime Organization (IMO) Regulation D-2. The effects of contact time and current density on inactivation were investigated. An increase in current density generally had a beneficial effect on the inactivation of the three species. E.faecalis and A.salina were more resistant to electrochemical disinfection than E. coli. The complete disinfection of E.coli was achieved in <8min at an applied current density of 253A/m(2). Complete inactivation of E. faecalis and A.salina was achieved at the same current density after 60 and 40min of contact time, respectively. A. salina inactivation follows first-order kinetics. Copyright © 2016 Elsevier Ltd. All rights reserved.

A low-energy intensive electrochemical system for the eradication of Escherichia coli from ballast water: Process development, disinfection chemistry, and kinetics modeling

International Nuclear Information System (INIS)

Nadeeshani Nanayakkara, K.G.; Khorshed Alam, A.K.M.; Zheng Yuming; Paul Chen, J.

2012-01-01

The invasion of biological organisms via ballast water has created threats to the environment and human health. In this study, a cost-effective electrochemical disinfection reactor was developed to inactivate Escherichia coli, one of the IMO-regulated indicator microbes, in simulated ballast water. The complete inactivation of E. coli could be achieved within a very short time (150, 120, or 60 s) with an energy consumption as low as 0.0090, 0.0074 or 0.0035 kWh/m 3 for ballast water containing E. coli at concentrations of 10 8 , 10 7 and 10 6 CFU/100 mL, respectively. Electrochemical chlorination was the major disinfection mechanism in chloride-abundant electrolytes, whereas oxidants such as ozone and free radicals contributed to 20% of the disinfection efficiency in chloride-free electrolytes. Moreover, a disinfection kinetics model was successfully developed to describe the inactivation of E. coli.

Alternative, indirect measures of ballast water treatment efficacy during a shipboard trial: a case study

NARCIS (Netherlands)

Wright, D.A.; Welschmeyer, N.A.; Peperzak, L.

2015-01-01

A shipboard study was conducted aboard the cruise ship Coral Princess during a scheduled cruise from San Pedro, CA, USA to Vancouver, British Columbia, Canada. The investigation involved three members of the global TestNet group, with experience in certification testing of ballast water treatment

A Feasibility Study on the Application of Basic Oxygen Furnace (BOF Steel Slag for Railway Ballast Material

Directory of Open Access Journals (Sweden)

Taehoon Koh

2018-01-01

Full Text Available Railway ballast, for which natural crushed stone aggregates have been generally used, is an essential track component for the distribution of train loads along the rails and sleepers to the roadbed. However, the use of natural crushed stone aggregate causes environmental destruction as well as dust production in train service. This paper evaluates the feasibility of using the basic oxygen furnace (BOF steel slag as railway ballast material. A series of physical and chemical quality tests are performed to investigate the characteristics of the materials associated with the effect of aging period due to the remaining free CaO and MgO in the BOF steel slag. Three different aging periods (i.e., 0, 3, and 6 months are used to compare with various standards and the properties of the crushed stone aggregates. It is demonstrated that the physical and chemical properties of the BOF steel slag with different aging periods satisfy all requirements of standards sufficiently. Especially, the BOF steel slag without aging (i.e., 0 month provides the similar physical and chemical properties, when compared to the BOF steel slag with aging (i.e., 3 and 6 months. Thus, it is possible to apply the BOF steel slag regardless of aging periods to the railway ballast materials instead of natural crushed stone aggregates.

Effect of type and concentration of ballasting particles on sinking rate of marine snow produced by the Appendicularian Oikopleura dioica

DEFF Research Database (Denmark)

Lombard, Fabien; Guidi, L.; Kiørboe, Thomas

2013-01-01

Ballast material (organic, opal, calcite, lithogenic) is suggested to affect sinking speed of aggregates in the ocean. Here, we tested this hypothesis by incubating appendicularians in suspensions of different algae or Saharan dust, and observing the sinking speed of the marine snow formed...... by their discarded houses. We show that calcite increases the sinking speeds of aggregates by ~100% and lithogenic material by ~150% while opal only has a minor effect. Furthermore the effect of ballast particle concentration was causing a 33 m d-1 increase in sinking speed for a 5×105 μm3 ml-1 increase in particle...

Algae viability over time in a ballast water sample

Science.gov (United States)

Gollasch, Stephan; David, Matej

2018-03-01

The biology of vessels' ballast water needs to be analysed for several reasons, one of these being performance tests of ballast water management systems. This analysis includes a viability assessment of phytoplankton. To overcome logistical problems to get algae sample processing gear on board of a vessel to document algae viability, samples may be transported to land-based laboratories. Concerns were raised how the storage conditions of the sample may impact algae viability over time and what the most appropriate storage conditions were. Here we answer these questions with a long-term algae viability study with daily sample analysis using Pulse-Amplitude Modulated (PAM) fluorometry. The sample was analysed over 79 days. We tested different storage conditions: fridge and room temperature with and without light. It seems that during the first two weeks of the experiment the viability remains almost unchanged with a slight downwards trend. In the continuing period, before the sample was split, a slightly stronger downwards viability trend was observed, which occurred at a similar rate towards the end of the experiment. After the sample was split, the strongest viability reduction was measured for the sample stored without light at room temperature. We concluded that the storage conditions, especially regarding temperature and light exposure, have a stronger impact on algae viability compared to the storage duration and that inappropriate storage conditions reduce algal viability. A sample storage time of up to two weeks in a dark and cool environment has little influence on the organism viability. This indicates that a two week time duration between sample taking on board a vessel and the viability measurement in a land-based laboratory may not be very critical.

There are Many Kinds and Brands of TL Lamp and Ballast Transformer in the Market

International Nuclear Information System (INIS)

Koes-Indrakoesoema; Yayan-Andryanto

2006-01-01

However, there is still a problem of how to determining the power factor (cos φ) for one of brand of lamp. Lamps with low power factor will consume relatively high reactive power, hence the active power that can be utilized decreases. One of the effort that can be done to improve the level of the lamp's power factor is to install a suitable capacitor with the lamp. The values of the lamp's power factor of a certain brand of lamp will be different if the lamp is connected with different brand of ballast transformer. Therefore, the value of the capacitor that have to be installed to the lamp also must be different depend on the brand of the transformer. This experiment using 2 (two) TL lamp i.e Chiyoda 40 Watt and Philip 36 Watt which has been installed with capacitor 3.6 μF and combination of ballast transformer Philips, National and Siemens and shows that increase the power factor until 0.95. (author)

Association of bacteria with marine invertebrates: Implications for ballast water management

Digital Repository Service at National Institute of Oceanography (India)

Khandeparker, L.; Anil, A.C.

stream_size 36739 stream_content_type text/plain stream_name EcoHealth_10_268a.pdf.txt stream_source_info EcoHealth_10_268a.pdf.txt Content-Encoding UTF-8 Content-Type text/plain; charset=UTF-8 1 Author version: EcoHealth... transportation, can have direct impact on society and human health. Ship’s ballast tanks hold different non-indigenous vertebrates, invertebrates, plants, microscopic algae, bacteria etc. (Williams et al. 1988; Carlton and Geller 1993; Smith et al. 1996...

Fluorescent lamp and ballast disposal-efficiency and the environment: Panel discussion

Energy Technology Data Exchange (ETDEWEB)

Bleasby, P.

1996-01-01

This panel discussion looked at the present state of problems related to the disposal of fluorescent lamps and ballasts. EPA has not issued a ruling defining what is to be done, and as a result different areas of the country, and different users are treating the products differently. The authors review the history of the problem, where the environmental concerns are, possible alternatives for disposal, be it landfill, recycling, incineration, or treatment as hazardous wastes, and policy concerns with regard to this issue.

Pilot-scale study of ballasted-flocculation technology

International Nuclear Information System (INIS)

Liem, L.E.; Brant, W.H.; Gagne, B.; Michaud, J.; Beaudet, J.-F.; Landry, D.; Braden, K.; Campbell, D.

2002-01-01

A ballasted-flocculation pilot-scale study was undertaken to treat a wide-range river water turbidity (17 to 2,608 NTU). The pilot-scale unit was operated at flowrates of 30 to 63 m 3 /h, which corresponded to loading rates of 40 to 84 m/h. Coagulants, polymers, and microsand were added to enhance the floc agglomeration. The weighted flocs settled rapidly resulting in excellent turbidity removals of 94.7 to 99.9%. At the peak turbidity, the unit had a 99.9% removal performance (2.7 from 2,608 NTU) at a loading rate of 40 m/h. In this case, polyaluminum silicosulfate and anionic polymer dosages were 82 and 1 mg/L, respectively. The microsand recycle rate was kept constant at 4.5 m 3 /h, and 1mg microsand was added for each liter of water treated. (author)

Generic Protocol for the Verification of Ballast Water Treatment Technology. Version 5.1

Science.gov (United States)

2010-09-01

and to build the scientific knowledge base needed to manage our ecological resources wisely, to understand how pollutants affect our health, and to...occurring in the water at the TF location. Ballast Water Treatment System (or System): Prefabricated , commercial-ready, treatment systems designed to...pathway to begin the development of technical procedures for approving BWTSs for installation on ships. EPA’s interest includes the ecological , economic

Tiny Stowaways: Analyzing the Economic Benefits of a U.S. Environmental Protection Agency Permit Regulating Ballast Water Discharges

Science.gov (United States)

Lovell, Sabrina J.; Drake, Lisa A.

2009-03-01

The U.S. Environmental Protection Agency has proposed permitting ballast water discharges—a benefit of which would be to reduce the economic damages associated with the introduction and spread of aquatic invasive species. Research on ship-borne aquatic invasive species has been conducted in earnest for decades, but determining the economic damages they cause remains troublesome. Furthermore, with the exception of harmful algal blooms, the economic consequences of microscopic invaders have not been studied, despite their potentially great negative effects. In this paper, we show how to estimate the economic benefits of preventing the introduction and spread of harmful bacteria, microalgae, and viruses delivered in U.S. waters. Our calculations of net social welfare show the damages from a localized incident, cholera-causing bacteria found in shellfish in the Gulf of Mexico, to be approximately 706,000 (2006). On a larger scale, harmful algal species have the potential to be transported in ships’ ballast tanks, and their effects in the United States have been to reduce commercial fisheries landings and impair water quality. We examine the economic repercussions of one bloom-forming species. Finally, we consider the possible translocation within the Great Lakes of a virus that has the potential to harm commercial and recreational fisheries. These calculations illustrate an approach to quantifying the benefits of preventing invasive aquatic microorganisms from controls on ballast water discharges.

Analysis of Bridge Transition Zones in Railways Considering the Moisture Condition of the Ballast and Subballast

NARCIS (Netherlands)

Wang, Haoyu; Silvast, Mika; Markine, V.L.; Wiljanen, Bruce

2017-01-01

Transition zones in railway tracks are the locations with considerable changes in vertical support structures, e.g., near bridges. Due to possible water flow constrictions in transition zone structures, there is frequently an increased moisture level in the ballast/subballast layers, which is a

Ballast water management that adapts to climate changes and reduces harmful bio-invasions in marine eco-systems

DEFF Research Database (Denmark)

Rasmussen, Lauge Baungaard; Hansen, Mette Sanne

2015-01-01

food-webs and eco-systems. Economic impacts include reductions in fisheries production and algae blooms harmful for fish farms, tourism and human health. Due to the rising temperatures of the Oceans, organisms that prefer a warm climate may take roots in marine ecosystems that were previously too cold...... in marine ecosystem of changed factors in the shipping sector, for instance change of number, size, and design of vessels as well as treatment technologies of ballast water. New areas for shipping due to climate changes are also included. Our study would contribute to improve decision support tools, usable...... for them. In addition, future changes of temperature, storm patterns and sea-currents may also change shipping routes and ballast water management practices. Based on methods like stock taking, trend tracking and scenario modeling the paper aims to evaluate possible ecological and economic impacts...

Density determination of railroad ballast by means of gamma radiation

International Nuclear Information System (INIS)

Mundt, M.

1983-01-01

Proceeding from the requirements of a measuring method for determining the degrees of densification and of soiling of railroad beds, conclusions are drawn for the use of a radiometric technique, considering measuring geometry, radiation energy, and instrumentation. Results obtained from laboratory experiments with a ballast pressure unit are presented. It is pointed out that the application of radiometric density measurements has to be linked with investigations of the behaviour of the rock species used, in order to obtain a valid interpretation of the measured density with regard to the properties and the composition of the railroad bed. (author)

Numerical modelling of the reinforcing effect of geosynthetic material used in a ballasted railway tracks

Czech Academy of Sciences Publication Activity Database

Jiroušek, Ondřej; Jíra, J.; Hrdlička, Ondřej; Kunecký, Jiří; Kytýř, Daniel; Vyčichl, J.; Doktor, Tomáš

2010-01-01

Roč. 224, č. 4 (2010), s. 259-267 ISSN 0954-4097 Institutional research plan: CEZ:AV0Z20710524 Keywords : railway track bed * reinforcing geogrid * finite-element modelling * settlement reduction * contact analysis * ballast material Subject RIV: JN - Civil Engineering Impact factor: 0.389, year: 2010 http://journals.pepublishing.com/content/k561040632411117/

The efficiency of combined coagulant and ballast to remove harmful cyanobacterial blooms in a tropical shallow system

NARCIS (Netherlands)

Miranda, Marcela; Noyma, Natalia; Pacheco, Felipe S.; de Magalhaes, Leonardo; Pinto, Ernani; Santos, Suzan; Soares, Maria Fernanda A.; Huszar, Vera L.; Lürling, Miquel; Marinho, Marcelo M.

We tested the hypothesis that a combination of coagulant and ballast could be efficient for removal of positively buoyant harmful cyanobacteria in shallow tropical waterbodies, and will not promote the release of cyanotoxins. This laboratory study examined the efficacy of coagulants [polyaluminium

The efficiency of combined coagulant and ballast to remove harmful cyanobacterial blooms in a tropical shallow system

NARCIS (Netherlands)

Miranda, Marcela; Noyma, Natália; Pacheco, Felipe S.; Magalhães, de Leonardo; Pinto, Ernani; Santos, Suzan; Soares, Maria Fernanda A.; Huszar, Vera L.; Lurling, Miguel; Marinho, Marcelo M.

2017-01-01

We tested the hypothesis that a combination of coagulant and ballast could be efficient for removal of positively buoyant harmful cyanobacteria in shallow tropical waterbodies, and will not promote the release of cyanotoxins. This laboratory study examined the efficacy of coagulants

Potential ballast water transfer of organisms from the west to the east coast of India: Insights through on board sampling

Science.gov (United States)

Desai, Dattesh V.; Narale, Dhiraj; Khandeparker, Lidita; Anil, Arga Chandrashekar

2018-03-01

The possibility of translocation of organisms via ship's ballast water (BW) during a voyage from Hazira on the west coast to Visakhapatnam on the east coast of India was assessed. Samples of BW during the voyage and discharge and sediment collected subsequent to discharge of BW were collected and analyzed for different abiotic and biotic components. It was observed that the salinity did not change, whereas temperature and pH of BW increased marginally during the voyage. A marginal increase in the dissolved oxygen is observed during rough-very rough sea conditions. A sharp decline in the phytoplankton and zooplankton abundance observed in the initial ballast tank sample compared to natural seawater indicates the impact of ballast water pumping on the plankton community. Changes in the sea state during the voyage (slight-moderate to rough-very rough) resulted in a higher sediment suspension rate and suspended particulate matter and this coincided with higher bacterial abundance followed by increase in phytoplankton. An increase in the phytoplankton abundance in the discharge water could be attributed to the inoculum from the sediment. The abundance of zooplankton decreased from the start till the end of the voyage, with high numbers of dead zooplankton in the discharge sample.

Analysis of the Dynamic Wheel Loads in Railway Transition Zones Considering the Moisture Condition of the Ballast and Subballast

Directory of Open Access Journals (Sweden)

Haoyu Wang

2017-11-01

Full Text Available Transition zones in railway tracks are the locations with considerable changes in vertical support structures, e.g., near bridges. Due to possible water flow constrictions in transition zone structures, there is frequently an increased moisture level in the ballast/subballast layers, which is a potential source of track degradation. This paper presents results of the moisture condition measured in three transition zones using ground penetrating radar, where the ballast/subballast are analyzed. The relationship between the moisture condition and track degradation in the transition zones is studied by comparing it to the longitudinal track level that is measured by the track inspection coaches. A strong connection is found between the high moisture condition and track degradation in the transition zones. The dynamic behavior of the transition zones with high moisture condition is analyzed using the Finite Element method. Differential stiffness and settlement are taken into consideration in the transition zone model, which is also coupled with a vehicle. The ballast/subballast layers are modelled as solid elements. Increased moisture conditions are considered as a reduction of elastic modulus, according to laboratory findings. Results show that high moisture leads to an increase of dynamic wheel loads in the transition zone, which explains the connection and confirms that the high moisture condition is a source of transition zone problems.

Implementación de un balastro electrónico con microcontrolador PIC para lámparas de sodio de alta presión; Implementation of electronic ballast with PIC microcontroller for high pressure sodiumlamps

Directory of Open Access Journals (Sweden)

Armando M. - Gutiérrez Menéndez

2013-10-01

Full Text Available En el presente trabajo se muestra un prototipo de balasto electrónico, que garantiza la operación exitosa en alta frecuencia de una lámpara de sodio de alta presión de 70 W, pues opera libre de resonancia acústica (RA. Se efectúa un análisis del fenómeno de la resonancia acústica, profundizando en su origen y predicción teórica. Es descrita la técnica de modulación en frecuencia utilizada para evitar este fenómeno, implementada en el microcontrolador de 8 bit PIC16F877 de la Microchip, la cual es activada en dependencia de la variación de los parámetros eléctricos de la lámpara, como son tensión y corriente. Son mostradas las etapas que dan conformación a dicho prototipo, además de presentarse las simulaciones realizadas a los principales elementos que componen el balasto. Los resultados prácticos alcanzados por el prototipo son expuestos, los cuales se dividen por etapas para analizar el correcto funcionamiento de cada una ellas.In the present work is offered a prototype of electronic ballast that guarantees the correctly operation in high frequency of a high pressure sodium lamp of 70 W, because it operates free of acoustic resonance (RA. An analysis of the phenomenon of the acoustic resonance is made, deepening in its origin and theoretical prediction. The modulation technique is described in frequency used to avoid this phenomenon, implemented in the microcontrolador of 8 bit PIC16F877 of Microchip, which is activated in dependence of the variation of the electric parameters of the lamp, like they are tension and current. They are shown the stages that give conformation to this prototype, besides the simulations carried out to the main elements that compose the ballast being presented. The practical results reached by the prototype are exposed, which are divided by stages to analyze the correct operation of each a them.

The effects of prolonged darkness on temperate and tropical marine phytoplankton, and their implications for ballast water risk management

Digital Repository Service at National Institute of Oceanography (India)

Carney, K.J.; Delany, J.E.; Sawant, S.S.; Mesbahi, E.

seawater promoted the highest levels of growth. Seasonality had a significant influence on species survival. Understanding the effects of all these factors can aid the development of effective risk assessments in ballast water management....

Data on metals (Zn, Al, Sr, and Co and metalloid (As concentration levels of ballast water in commercial ships entering Bushehr port, along the Persian Gulf

Directory of Open Access Journals (Sweden)

Farshid Soleimani

2016-12-01

Full Text Available In this article, we determined the concentration levels of metals including Zn, Al, Sr, and Co and metalloid of As of ballast water in commercial ships entering Bushehr port, along the Persian Gulf. Ballast water samples were taken from commercial ships entering Bushehr port from 34 ports around the world during 15 February and 25 August 2016. The concentration levels of metals and metalloid were determined by using a graphite furnace absorption spectrometer (AAS.

49 CFR 1242.15 - Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast...

Science.gov (United States)

2010-10-01

... 49 Transportation 9 2010-10-01 2010-10-01 false Roadway, tunnels and subways, bridges and culverts, ties, rails, other track material, ballast, track laying and surfacing, and road property damaged... RAILROADS 1 Operating Expenses-Way and Structures § 1242.15 Roadway, tunnels and subways, bridges and...

On board short-time high temperature heat treatment of ballast water: a field trial under operational conditions.

Science.gov (United States)

Quilez-Badia, Gemma; McCollin, Tracy; Josefsen, Kjell D; Vourdachas, Anthony; Gill, Margaret E; Mesbahi, Ehsan; Frid, Chris L J

2008-01-01

A ballast water short-time high temperature heat treatment technique was applied on board a car-carrier during a voyage from Egypt to Belgium. Ballast water from three tanks was subjected for a few seconds to temperatures ranging from 55 degrees C to 80 degrees C. The water was heated using the vessel's heat exchanger steam and a second heat exchanger was used to pre-heat and cool down the water. The treatment was effective at causing mortality of bacteria, phytoplankton and zooplankton. The International Maritime Organization (IMO) standard was not agreed before this study was carried out, but comparing our results gives a broad indication that the IMO standard would have been met in some of the tests for the zooplankton, in all the tests for the phytoplankton; and probably on most occasions for the bacteria. Passing the water through the pump increased the kill rate but increasing the temperature above 55 degrees C did not improve the heat treatment's efficacy.

Simulation of gamma irradiation system for a ballast water treatment

International Nuclear Information System (INIS)

Faez, T. P.; Sarkar, S.

2006-01-01

Invasion by different kinds of ballast the water microorganisms is one of the most important marine environment problems around the world therefore preventing the invasion of these unwanted and harmful stowaways is one of the main strategies of responsible agencies. Some of these methods such as ocean exchange, heating, filtration, hydro cyclones, UV irradiation and chemical treatment, have various problems such as technical deficiency, high costs, lack of safety and environmental side effects. Materials and Methods: A novel system of treatment by Gamma irradiation is designed to irradiate the blast water uniformly and effectively. To determine the dose distribution as a function of distance from the irradiation source, the MCNP code was used. The systems used for source implant in this simulation were Paterson-Parker, Paris and Network systems. In each system, Sivert-integral and inverse square law were used in MATLAB program to determine the dose distribution. Results: Results of initial laboratory tests on offshore water samples of Siri Island indicated that the appropriate dose for deactivation of organisms of water samples is approximately one kGy. It has been demonstrated that the dose can be provided by twenty five 100,000 Ci line sources of ' 60 Co in a triangle implant arranged in a 1*1*1 m3 cubic shape water pipe. In order to increase efficiency and radiation safety, water passed from two other coaxial and bigger cubes, after passing from the first cube. A one meter thick wall of concrete around the cubes was adequate to shield the system completely. Conclusion: The main advantages of this system such as high efficiency, safety, reliability, minimum environmental adverse effects, proves that this novel method not only can be used for ballast water treatment, but is also effective for drinking water purification

Amplicon-Based Pyrosequencing Reveals High Diversity of Protistan Parasites in Ships' Ballast Water: Implications for Biogeography and Infectious Diseases.

Science.gov (United States)

Pagenkopp Lohan, K M; Fleischer, R C; Carney, K J; Holzer, K K; Ruiz, G M

2016-04-01

Ships' ballast water (BW) commonly moves macroorganisms and microorganisms across the world's oceans and along coasts; however, the majority of these microbial transfers have gone undetected. We applied high-throughput sequencing methods to identify microbial eukaryotes, specifically emphasizing the protistan parasites, in ships' BW collected from vessels calling to the Chesapeake Bay (Virginia and Maryland, USA) from European and Eastern Canadian ports. We utilized tagged-amplicon 454 pyrosequencing with two general primer sets, amplifying either the V4 or V9 domain of the small subunit (SSU) of the ribosomal RNA (rRNA) gene complex, from total DNA extracted from water samples collected from the ballast tanks of bulk cargo vessels. We detected a diverse group of protistan taxa, with some known to contain important parasites in marine systems, including Apicomplexa (unidentified apicomplexans, unidentified gregarines, Cryptosporidium spp.), Dinophyta (Blastodinium spp., Euduboscquella sp., unidentified syndinids, Karlodinium spp., Syndinium spp.), Perkinsea (Parvilucifera sp.), Opisthokonta (Ichthyosporea sp., Pseudoperkinsidae, unidentified ichthyosporeans), and Stramenopiles (Labyrinthulomycetes). Further characterization of groups with parasitic taxa, consisting of phylogenetic analyses for four taxa (Cryptosporidium spp., Parvilucifera spp., Labyrinthulomycetes, and Ichthyosporea), revealed that sequences were obtained from both known and novel lineages. This study demonstrates that high-throughput sequencing is a viable and sensitive method for detecting parasitic protists when present and transported in the ballast water of ships. These data also underscore the potential importance of human-aided dispersal in the biogeography of these microbes and emerging diseases in the world's oceans.

Inactivation characteristics of ozone and electrolysis process for ballast water treatment using B. subtilis spores as a probe.

Science.gov (United States)

Jung, Youmi; Yoon, Yeojoon; Hong, Eunkyung; Kwon, Minhwan; Kang, Joon-Wun

2013-07-15

Since ballast water affects the ocean ecosystem, the International Maritime Organization (IMO) sets a standard for ballast water management and might impose much tighter regulations in the future. The aim of this study is to evaluate the inactivation efficiency of ozonation, electrolysis, and an ozonation-electrolysis combined process, using B. subtilis spores. In seawater ozonation, HOBr is the key active substance for inactivation, because of rapid reactivity of ozone with Br(-) in seawater. In seawater electrolysis, it is also HOBr, but not HOCl, because of the rapid reaction of HOCl with Br(-), which has not been recognized carefully, even though many electrolysis technologies have been approved by the IMO. Inactivation pattern was different in ozonation and electrolysis, which has some limitations with the tailing or lag-phase, respectively. However, each deficiency can be overcome with a combined process, which is most effective as a sequential application of ozonation followed by electrolysis. Copyright © 2013 Elsevier Ltd. All rights reserved.

33 CFR Appendix D to Part 157 - Example of a Procedure for Dedicated Clean Ballast Tanks Operations

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Example of a Procedure for... ENVIRONMENT RELATING TO TANK VESSELS CARRYING OIL IN BULK Pt. 157, App. D Appendix D to Part 157—Example of a Procedure for Dedicated Clean Ballast Tanks Operations 1. Source. The example procedure for dedicated clean...

Optimal Control of a Ballast-Stabilized Floating Wind Turbine

DEFF Research Database (Denmark)

Christiansen, Søren; Knudsen, Torben; Bak, Thomas

2011-01-01

Offshore wind energy capitalizes on the higher and less turbulent wind speeds at sea. The use of floating structures for deeper waters is being explored. The control objective is a tradeoff between power capture and fatigue, especially that produced by the oscillations caused by the reduced...... structural stiffness of a floating installation in combination with a coupling between the fore–aft motion of the tower and the blade pitch. To address this problem, the present paper models a ballast-stabilized floating wind turbine, and suggests a linear quadratic regulator (LQR) in combination with a wind...... estimator and a state observer. The results are simulated using aero elastic code and analysed in terms of damage equivalent loads. When compared to a baseline controller, this controller clearly demonstrates better generator speed and power tracking while reducing fatigue loads....

Implementación de un balastro electrónico con microcontrolador PIC para lámparas de sodio de alta presión Implementation of electronic ballast with PIC microcontroller for high pressure sodiumlamps

Directory of Open Access Journals (Sweden)

Armando Manuel Gutiérrez Menéndez

2013-09-01

Full Text Available En el presente trabajo se muestra un prototipo de balasto electrónico, que garantiza la operación exitosa en alta frecuencia de una lámpara de sodio de alta presión de 70 W, pues opera libre de resonancia acústica (RA. Se efectúa un análisis del fenómeno de la resonancia acústica, profundizando en su origen y predicción teórica. Es descrita la técnica de modulación en frecuencia utilizada para evitar este fenómeno, implementada en el microcontrolador de 8 bit PIC16F877 de la Microchip, la cual es activada en dependencia de la variación de los parámetros eléctricos de la lámpara, como son tensión y corriente. Son mostradas las etapas que dan conformación a dicho prototipo, además de presentarse las simulaciones realizadas a los principales elementos que componen el balasto. Los resultados prácticos alcanzados por el prototipo son expuestos, los cuales se dividen por etapas para analizar el correcto funcionamiento de cada una ellas.Palabra clave: In the present work is offered a prototype of electronic ballast that guarantees the correctly operation in high frequency of a high pressure sodium lamp of 70 W, because it operates free of acoustic resonance (RA. An analysis of the phenomenon of the acoustic resonance is made, deepening in its origin and theoretical prediction. The modulation technique is described in frequency used to avoid this phenomenon, implemented in the microcontrolador of 8 bit PIC16F877 of Microchip, which is activated in dependence of the variation of the electric parameters of the lamp, like they are tension and current. They are shown the stages that give conformation to this prototype, besides the simulations carried out to the main elements that compose the ballast being presented. The practical results reached by the prototype are exposed, which are divided by stages to analyze the correct operation of each a them.Key words:

Investigation of the connection between plasma temperature and electrode temperature in metal-halide lamps

International Nuclear Information System (INIS)

Fromm, D.C.; Gleixner, K.H.; Lieder, G.H.

2002-01-01

Spatial profiles of electrode temperatures and plasma temperatures have been measured on 'real' HID lamps filled with a commercial metal-halide compound. The absolute accuracy of pyrometric determination of electrode tip temperatures was ±30 K, while the determination of plasma core temperatures, using a modified Bartels method, has an accuracy of ±100 K. We could deduce a close correlation between the plasma temperature in front of an electrode T p and its tip temperature T t due to the influence of the cataphoresis. If T p is reduced at the cathode the T t value has also lowered, whereas T p at the anode is raised together with its T t data. This correlation disappears at ballast frequencies above 100 Hz, whereas the cataphoresis influence on T p continues up to 500 Hz. Based on the latter limit, a rough estimation of the cataphoresis velocity delivers 700 cm s -1 . As a tentative interpretation, we suggest that the connection between T p and T t is caused by an increase of the ion part of the total current at the cathode due to Na accumulation before it. Thus, the cathode has to emit fewer electrons and works at a lower temperature. Further results are the temporal behaviour of T t depends on the ballast type. For vertical operation the strong influence of convection on T t has also to be taken into account. Above 100 Hz, where only convection plays a role, the upper electrode T t exceeds the T t value of the lower electrode by nearly 400 K. This discrepancy one may explain, tentatively, by convection heating of the upper electrode and convection cooling of the lower one. (author)

Production, oxygen respiration rates, and sinking velocity of copepod fecal pellets: Direct measurements of ballasting by opal and calcite

DEFF Research Database (Denmark)

Ploug, H.; Iversen, M.H.; Koski, Marja

2008-01-01

sp., T. weissflogii, and E. huxleyi, respectively. The average carbon-specific respiration rate was 0.15 d(-1) independent on diet (range: 0.08-0.21 d(-1)). Because of ballasting of opal and calcite, sinking velocities were significantly higher for pellets produced on T. weissflogii (322 +/- 169 m d...

Development of a Modular, Provider Customized Airway Trainer

Science.gov (United States)

2015-11-25

data used to evaluate student performance. This transformation was done by the Airway Firmware on an Arduino Leonardo. The Airway Firmware transmitted...USB HID protocol, the Arduino Leonardo was selected. Figure 13: Electronics and Firmware W911NF-13-2-0033 Airway II Final Report...CREST U of MN Nov 2015 Page 12 of 35 The microchip, around which the Arduino Leonardo was built, readily supported USB HID through

Optimisation of bitumen emulsion properties for ballast stabilisation; Optimización de las propiedades de emulsión de betún para la estabilización de balasto.

Energy Technology Data Exchange (ETDEWEB)

D’Angelo, G.; Lo Presti, D.; Thom, N.

2017-07-01

Ballasted track, while providing economical and practical advantages, is associated with high costs and material consumption due to frequent maintenance. More sustainable alternatives to conventional ballasted trackbeds should therefore aim at extending its durability, particularly considering ongoing increases in traffic speed and loads. In this regard, the authors have investigated a solution consisting of bitumen stabilised ballast (BSB), designed to be used for new trackbeds as well as in reinforcing existing ones. This study presents the idea behind the technology and then focuses on a specific part of its development: the optimisation of bitumen emulsion properties and dosage in relation to ballast field conditions. Results showed that overall bitumen stabilisation improved ballast resistance to permanent deformation by enhancing stiffness and damping properties. Scenarios with higher dosage of bitumen emulsion, higher viscosity, quicker setting behaviour, and harder base bitumen seem to represent the most desirable conditions to achieve enhanced in-field performance. [Spanish] El balasto proporciona ventajas económicas y prácticas, sin embargo se asocia con altos costos y consumo de materiales. Las alternativas más sostenibles deben tener como objetivo extender la durabilidad del balasto, sobre todo teniendo en cuenta los actuales incrementos en la velocidad y las cargas del tráfico. Los autores presentan una solución que consiste en estabilizar el balasto con betún. Este estudio describe la tecnología y se centra en la optimización de las propiedades de la emulsión bituminosa y su dosis en función de las condiciones del balasto. Los resultados muestran que la stabilización con betún mejora la resistencia a la deformación permanente mediante la modificación de la rigidez y las propiedades de amortiguación. Pruebas con mayor dosis de emulsión bituminosa, mayor viscosidad, fraguado rápido y betún base más duro, representan las condiciones m

Molecular detection of native and invasive marine invertebrate larvae present in ballast and open water environmental samples collected in Puget Sound

Science.gov (United States)

Harvey, J.B.J.; Hoy, M.S.; Rodriguez, R.J.

2009-01-01

Non-native marine species have been and continue to be introduced into Puget Sound via several vectors including ship's ballast water. Some non-native species become invasive and negatively impact native species or near shore habitats. We present a new methodology for the development and testing of taxon specific PCR primers designed to assess environmental samples of ocean water for the presence of native and non-native bivalves, crustaceans and algae. The intergenic spacer regions (IGS; ITS1, ITS2 and 5.8S) of the ribosomal DNA were sequenced for adult samples of each taxon studied. We used these data along with those available in Genbank to design taxon and group specific primers and tested their stringency against artificial populations of plasmid constructs containing the entire IGS region for each of the 25 taxa in our study, respectively. Taxon and group specific primer sets were then used to detect the presence or absence of native and non-native planktonic life-history stages (propagules) from environmental samples of ballast water and plankton tow net samples collected in Puget Sound. This methodology provides an inexpensive and efficient way to test the discriminatory ability of taxon specific oligonucleotides (PCR primers) before creating molecular probes or beacons for use in molecular ecological applications such as probe hybridizations or microarray analyses. This work addresses the current need to develop molecular tools capable of diagnosing the presence of planktonic life-history stages from non-native marine species (potential invaders) in ballast water and other environmental samples. ?? 2008 Elsevier B.V.

Risk assessment of human health from exposure to the discharged ballast water after full-scale electrolysis treatment.

Science.gov (United States)

Zhang, Nahui; Wang, Yidan; Xue, Junzeng; Yuan, Lin; Wang, Qiong; Liu, Liang; Wu, Huixian; Hu, Kefeng

2016-06-01

The presence of disinfection by-products (DBPs) releasing from ballast water management systems (BWMS) can cause a possible adverse effects on humans. The objectives of this study were to compute the Derived No Effect Levels (DNELs) for different exposure scenarios and to compare these levels with the exposure levels from the measured DBPs in treated ballast water. The risk assessment showed that when using animal toxicity data, all the DNELs values were approximately 10(3)-10(12) times higher than the exposure levels of occupational and general public exposure scenarios, indicating the level of risk was low (risk characterization ratios (RCRs) < 1). However, when using human data, the RCRs were higher than 1 for dichlorobromomethane and trichloromethane, indicating that the risk of adverse effects on human were significant. This implies that there are apparent discrepancies between risk characterization from animal and human data, which may affect the overall results. We therefore recommend that when appropriate, human data should be used in risk assessment as much as possible, although human data are very limited. Moreover, more appropriate assessment factors can be considered to be employed in estimating the DNELs for human when the animal data is selected as the dose descriptors. Copyright © 2016 Elsevier Inc. All rights reserved.

Effects of Battery Voltage in Fluorescent Lamps for Use in Photovoltaic Systems; Efectos de la Tension de Bateria en Lamparas Fluorescentes para Uso en Instalaciones Fotovoltaicas

Energy Technology Data Exchange (ETDEWEB)

Garcia Rosillo, F; Egido Aguilera, M A

2008-07-01

It is known the importance of lighting systems with fluorescent lamps and electronic ballast in isolated photo-voltaic systems. The positive characteristics of the fluorescent lamps sometimes are not developed in full, due to the incorrect choice of ballast The failure of a lamp in the photovoltaic system can have great significance in the subjective perception of the user for the complete system. The purpose of this study is to analyze the behavior of two very similar fluorescent lamps, fed with different electronic ballasts, showing the great influence of the electronic ballast topology in the operation of the fluorescent lamp. In particular, this work aims to analyze the effect of variations of the input voltage to the ballast in the electrical and luminous characteristics of the lamp, as well as to understand the influence of electrical parameters in the life time of the fluorescent lamp. It is also analyzed the operating temperature of the electrode and the time necessary for electrode cooling after switching off the lamp. (Author) 23 refs.

10 CFR Appendix Q to Subpart B of... - Uniform Test Method for Measuring the Energy Consumption of Fluorescent Lamp Ballasts

Science.gov (United States)

2010-01-01

... 10 Energy 3 2010-01-01 2010-01-01 false Uniform Test Method for Measuring the Energy Consumption... Appendix Q to Subpart B of Part 430—Uniform Test Method for Measuring the Energy Consumption of Fluorescent... reference; see § 430.3). The test for measuring standby mode energy consumption of fluorescent lamp ballasts...

Conference on Ballast Water and Waste Water Treatment Aboard Ships and in Ports. Held in Bremerhaven, Germany on 11-13 June 2003

Science.gov (United States)

2003-06-13

test guidelines. Residual PERACLEAN® OCEAN in ballast water decomposes to water, acetic acid (e.g., vinegar ) and oxygen. The half-life is in the...membrane bioreactors (Figure 1), the combination of high cell density fermentation with ultrafiltration in compact modularI plants /2/. I! I I i Figure

Effects of sonication and advanced chemical oxidants on the unicellular green alga Dunaliella tertiolecta and cysts, larvae and adults of the brine shrimp Artemia salina: a prospective treatment to eradicate invasive organisms from ballast water.

Science.gov (United States)

Gavand, Meghana R; McClintock, James B; Amsler, Charles D; Peters, Robert W; Angus, Robert A

2007-11-01

Uptake and release of ship-borne ballast water is a major factor contributing to introductions of aquatic phytoplankton and invasive macroinvertebrates. Some invasive unicellular algae can cause harmful algal blooms and produce toxins that build up in food chains. Moreover, to date, few studies have compared the efficacy of ballast water treatments against different life history phases of aquatic macroinvertebrates. In the present study, the unicellular green alga Dunaliella tertiolecta, and three discrete life history phases of the brine shrimp Artemia salina, were independently used as model organisms to study the efficacy of sonication as well as the advanced oxidants, hydrogen peroxide and ozone, as potential ballast water treatments. Algal cells and brine shrimp cysts, nauplii, and adults were subjected to individual and combined treatments of sonication and advanced oxidants. Combined rather than individual treatments consistently yielded the highest levels of mortality in algal cells (100% over a 2 min exposure) and in brine shrimp (100% and 95% for larvae and adults, respectively, over a 2 min exposure). In contrast, mortality levels in brine shrimp cysts (66% over 2 min; increased to 92% over a 20 min exposure) were moderately high but consistently lower than that detected for larval or adult shrimp. Our results indicate that a combination of sonication and advanced chemical oxidants may be a promising method to eradicate aquatic unicellular algae and macroinvertebrates in ballast water.

Light Sources and Lighting Circuits

Science.gov (United States)

Honda, Hisashi; Suwa, Takumi; Yasuda, Takeo; Ohtani, Yoshihiko; Maehara, Akiyoshi; Okada, Atsunori; Komatsu, Naoki; Mannami, Tomoaki

According to the Machinery Statistics of the Ministry of Economy, Trade and Industry, the production of incandescent lamps in Japan in 2007 was 990 million units (90.0% of the previous year's total), in which the production of incandescent lamps for general lighting was 110 million units (90.0% of the previous year's total) and of tungsten-halogen lamps was 44 million units (96.6% of the previous year's total). The production of fluorescent lamps was 927 million units (93.9% of the previous year's total), in which general fluorescent lamps, excluding those for LCD back lighting, was 320 million units (87.2% of the previous year's total). Also, the production of HID lamps was 10 million units (101.5% of the previous year's total). On the other hand, when the numbers of sales are compared with the sales of the previous year, incandescent lamps for general use was 99.8%, tungsten-halogen lamps was 96.9%, fluorescent lamps was 95.9%, and HID lamps was 98.9%. Self-ballasted fluorescent lamps alone showed an increase in sales as strong as 29 million units, or 121.7% of the previous year's sales. It is considered that the switchover of incandescent lamps to HID lamps was promoted for energy conservation and carbon dioxide reduction with the problem of global warming in the background. In regard to exhibitions, Lighting Fair 2007 was held in Tokyo in March, and LIGHTFAIR INTERNATIONAL 2007 was held in New York in May. Regarding academic conferences, LS:11 (the 11th International Symposium on the Science & Technology of Light Sources) was held in Shanghai in May, and the First International Conference on White LEDs and Solid State Lighting was held in Tokyo in November. Both conferences suggested that there are strong needs and concerns now about energy conservation, saving natural resources, and restrictions of hazardous materials. In regard to incandescent lamps, the development of products aiming at higher efficacy, electric power savings, and longer life was advanced by

Effects of UV/Ag-TiO2/O3 advanced oxidation on unicellular green alga Dunaliella salina: implications for removal of invasive species from ballast water.

Science.gov (United States)

Wu, Donghai; You, Hong; Du, Jiaxuan; Chen, Chuan; Jin, Darui

2011-01-01

The UV/Ag-TiO2/O3 process was investigated for ballast water treatment using Dunaliella salina as an indicator. Inactivation curves were obtained, and the toxicity of effluent was determined. Compared with individual unit processes using ozone or UV/Ag-TiO2, the inactivation efficiency of D. salina by the combined UV/Ag-TiO2/O3 process was enhanced. The presence of ozone caused an immediate decrease in chlorophyll a (chl-a) concentration. Inactivation efficiency and ch1-a removal efficiency were positively correlated with ozone dose and ultraviolet intensity. The initial total residual oxidant (TRO) concentration of effluent increased with increasing ozone dose, and persistence of TRO resulted in an extended period of toxicity. The results suggest that UV/Ag-TiO2/O3 has potential for ballast water treatment.

Ergonomics evaluation of work posture in OWAS method in Ballast mines

Directory of Open Access Journals (Sweden)

Nasl Seraji J

1999-08-01

Full Text Available In this study, musculoskeletal disorders incidents have been found through NMQ. Then, with the OWAS method the results have been analysed. In this thesis, we have studied the case in two different workshops of Ballast Production Company. The jobs were classified according to static load caused by poor work posture and recommendations for reducing the hurmful load were made. The study of the questionnaire showe that there is meaningful relation between work experience and Low Back Pain (LBP (P<3%. Meanwhile BMI (Body Mass Index is closely related to LBP (P<2%. However a relation was found between low back and back and shoulder pain complaints during recent one year and last one week with that of the existence of the pains, respectively P<2% and P<5%. Jobs related with repair and maintenance rates the first as regards static load on the muscloskeletal system. Cooking, digging operations, driving bullodozer, operation of stone crushing device, loaders and lorries rank respectively in order.

A semi-empirical model for the prediction of fouling in railway ballast using GPR

Science.gov (United States)

Bianchini Ciampoli, Luca; Tosti, Fabio; Benedetto, Andrea; Alani, Amir M.; Loizos, Andreas; D'Amico, Fabrizio; Calvi, Alessandro

2016-04-01

The first step in the planning for a renewal of a railway network consists in gathering information, as effectively as possible, about the state of the railway tracks. Nowadays, this activity is mostly carried out by digging trenches at regular intervals along the whole network, to evaluate both geometrical and geotechnical properties of the railway track bed. This involves issues, mainly concerning the invasiveness of the operations, the impacts on the rail traffic, the high costs, and the low levels of significance concerning such discrete data set. Ground-penetrating radar (GPR) can represent a useful technique for overstepping these issues, as it can be directly mounted onto a train crossing the railway, and collect continuous information along the network. This study is aimed at defining an empirical model for the prediction of fouling in railway ballast, by using GPR. With this purpose, a thorough laboratory campaign was implemented within the facilities of Roma Tre University. In more details, a 1.47 m long × 1.47 m wide × 0.48 m height plexiglass framework, accounting for the domain of investigation, was laid over a perfect electric conductor, and filled up with several configuration of railway ballast and fouling material (clayey sand), thereby representing different levels of fouling. Then, the set of fouling configurations was surveyed with several GPR systems. In particular, a ground-coupled multi-channel radar (600 MHz and 1600 MHz center frequency antennas) and three air-launched radar systems (1000 MHz and 2000 MHz center frequency antennas) were employed for surveying the materials. By observing the results both in terms of time and frequency domains, interesting insights are highlighted and an empirical model, relating in particular the shape of the frequency spectrum of the signal and the percentage of fouling characterizing the surveyed material, is finally proposed. Acknowledgement The Authors thank COST, for funding the Action TU1208 "Civil

The Maritime Environment - International Conference and Exhibition on Ballast Water, Waste Water and Sewage Treatment on Ships and in Ports Held in Bremerhaven, Germany on 12-14 September 2001. Conference Proceedings

National Research Council Canada - National Science Library

2001-01-01

The Maritime International Conference on Ballast Water, Waste Water and Sewage Treatment on Ships and in Ports held in Bremerhaven, Germany on 12-14 September 2001 was cosponsored by Deerberg-Systems...

CMOS based image cytometry for detection of phytoplankton in ballast water.

Science.gov (United States)

Pérez, J M; Jofre, M; Martínez, P; Yáñez, M A; Catalan, V; Parker, A; Veldhuis, M; Pruneri, V

2017-02-01

We introduce an image cytometer (I-CYT) for the analysis of phytoplankton in fresh and marine water environments. A linear quantification of cell numbers was observed covering several orders of magnitude using cultures of Tetraselmis and Nannochloropsis measured by autofluorescence in a laboratory environment. We assessed the functionality of the system outside the laboratory by phytoplankton quantification of samples taken from a marine water environment (Dutch Wadden Sea, The Netherlands) and a fresh water environment (Lake Ijssel, The Netherlands). The I-CYT was also employed to study the effects of two ballast water treatment systems (BWTS), based on chlorine electrolysis and UV sterilization, with the analysis including the vitality of the phytoplankton. For comparative study and benchmarking of the I-CYT, a standard flow cytometer was used. Our results prove a limit of detection (LOD) of 10 cells/ml with an accuracy between 0.7 and 0.5 log, and a correlation of 88.29% in quantification and 96.21% in vitality, with respect to the flow cytometry results.

Power supply improvements for ballasts-low pressure mercury/argon discharge lamp for water purification

Science.gov (United States)

Bokhtache, A. Aissa; Zegaoui, A.; Djahbar, A.; Allouache, H.; Hemici, K.; Kessaissia, F. Z.; Bouchrit, M. S.; Aillerie, M.

2017-02-01

The low-pressure electrical discharges established in the mercury rare gas mixtures are the basis of many applications both in the field of lighting and for industrial applications. In order to select an efficient high frequency power supply (ECG -based PWM inverter), we present and discuss results obtained in the simulation of three kinds of power supplies delivering a 0.65 A - 50KHz sinusoidal current dedicated to power low pressure UV Mercury - Argon lamp used for effect germicide on water treatment thus allowing maximum UVC radiation at 253.7 nm. Three ballasts half-bridge configurations were compared with criteria based on resulting germicide efficiency, electrical yield and reliability, for example the quality of the sinusoidal current with reduced THD, and finally, we also considered in this analysis the final economic aspect.

Innovative Ballasted Flat Roof Solar PV Racking System

Energy Technology Data Exchange (ETDEWEB)

Peek, Richard T. [Cascade Engineering, Grand Rapids, MI (United States)

2014-12-15

The objective of this project was to reduce the cost of racking for PV solar on flat commercial rooftops. Cost reductions would come from both labor savings and material savings related to the installation process. The rack would need to accommodate the majority of modules available on the market. Cascade Engineering has a long history of converting traditional metal type applications over to plastic. Injection molding of plastics have numerous advantages including selection of resin for the application, placing the material exactly where it is needed, designing in features that will speed up the installation process, and weight reduction of the array. A plastic rack would need to meet the requirements of UL2703, Mounting systems, mounting devices, clamping/retention devices, and ground lugs for use with flat-plate photovoltaic modules and panels. Comparing original data to the end of project racking design, racking material costs were reduced 50% and labor costs reduced 64%. The racking product accommodates all 60 and 72 cell panels on the market, meets UL2703 requirements, contributes only 1.3 pounds per square foot of weight to the array, requires little ballast to secure the array, automatically grounds the module when the module is secured, stacks/nests well for shipping/fewer lifts to the roof, provides integrated wire routing, allows water to drain on the roof, and accommodates various seismic roof connections. Project goals were achieved as noted in the original funding application.

Overcoming challenges integrating patient-generated data into the clinical EHR: lessons from the CONtrolling Disease Using Inexpensive IT--Hypertension in Diabetes (CONDUIT-HID) Project.

Science.gov (United States)

Marquard, Jenna L; Garber, Lawrence; Saver, Barry; Amster, Brian; Kelleher, Michael; Preusse, Peggy

2013-10-01

The CONDUIT-HID intervention integrates patients' electronic blood pressure measurements directly into the clinical EHR using Microsoft HealthVault as an intermediary data store. The goal of this paper is to describe generalizable categories of patient and technical challenges encountered in the development and implementation of this inexpensive, commercial off-the-shelf consumer health informatics intervention, examples of challenges within each category, and how the example challenges were resolved prior to conducting an RCT of the intervention. The research team logged all challenges and mediation strategies during the technical development of the intervention, conducted home visits to observe patients using the intervention, and conducted telephone calls with patients to understand challenges they encountered. We then used these data to iteratively refine the intervention. The research team identified a variety of generalizable categories of challenges associated with patients uploading data from their homes, patients uploading data from clinics because they did not have or were not comfortable using home computers, and patients establishing the connection between HealthVault and the clinical EHR. Specific challenges within these categories arose because: (1) the research team had little control over the device and application design, (2) multiple vendors needed to coordinate their actions and design changes, (3) the intervention use cases were not anticipated by the device and application designers, (4) PHI accessed on clinic computers needed to be kept secure, (5) the research team wanted the data in the clinical EHR to be valid and reliable, (6) patients needed the ability to share only the data they wanted, and (7) the development of some EHR functionalities were new to the organization. While these challenges were varied and complex, the research team was able to successfully resolve each one prior to the start of the RCT. By identifying these

Jet-Suspended, Calcite-Ballasted Cyanobacterial Waterwarts in a Desert Spring

Science.gov (United States)

Pichel-Garcia, Ferran; Wade, Bman D.; Farmer, Jack D.

2002-01-01

We describe a population of colonial cyanobacteria (waterwarts) that develops as the dominant primary producer in a bottom-fed, warm spring in the Cuatro Cienegas karstic region of the Mexican Chihuahuan Desert. The centimeter-sized waterwarts were suspended within a central, conically shaped, 6-m deep well by upwelling waters. Waterwarts were built by an unicellular cyanobacterium and supported a community of epiphytic filamentous cyanobacteria and diatoms but were free of heterotrophic bacteria inside. Sequence analysis of genes revealed that this cyanobacterium is only distantly related to several strains of other unicellular teria Cyanothece, Waterwarts contained orderly arrangements of mineral made up of microcrystalline low-magnesium calcite with high levels of strontium and sulfur. Waterwarts were 95.9% (v/v) glycan, 2.8% cells, and 1.3% mineral grains and had a buoyant density of 1.034 kg/L. An analysis of the hydrological properties of the spring well and the waterwarts demonstrated that both large colony size and the presence of controlled amounts of mineral ballast are required to prevent the population from being washed out of the well. The unique hydrological characteristics of the spring have likely selected for both traits. The mechanisms by which controlled nucleation of extracellular calcite is achieved remain to be explored.

Effect and mechanism of a High Gradient Magnetic Separation (HGMS) and Ultraviolet (UV) composite process on the inactivation of microbes in ballast water

International Nuclear Information System (INIS)

Ren, Zhijun; Zhang, Lin; Shi, Yue; Leng, Xiaodong; Shao, Jingchao

2016-01-01

The patented technology of a High Gradient Magnetic Separation (HGMS)-Ultraviolet (UV) composite process was used to treat ballast water. Staphylococcus aureus (S. aureus) was selected as the reference bacteria. After treatment by the HGMS-UV process, the concentration of S. aureus on the log 10 scale was lower than 2 at different flow rates, S. aureus suffered the most serious damage, and K + leakage of the bacteria was 1.73 mg/L higher than separate 60 min UV irradiation (1.17 mg/L) and HGMS (0.12 mg/L) processes. These results demonstrated that the HGMS-UV composite process was an effective approach to treat ballast water. Further, the HGMS process had synergistic action on the subsequent UV irradiation process and accelerated cell membrane damage. Meanwhile, the results of superoxide dismutase (SOD) activities of bacteria and DNA band analyses indicated that the inactivation mechanisms were different for HGMS and UV irradiation. - Highlights: •The HGMS process had synergistic action on the subsequent UV irradiation process. •HGMS directly influenced the active center of a metal enzyme and did not cause damage to DNA. •UV irradiation was found to depend on the production of free radicals to affect the bacterial DNA and enzyme activity.

Analysis of federal policy options for improving US lighting energy efficiency: Commercial and residential buildings

Energy Technology Data Exchange (ETDEWEB)

Atkinson, B.A.; McMahon, J.E.; Mills, E.; Chan, P.; Chan, T.W.; Eto, J.H.; Jennings, J.D.; Koomey, J.G.; Lo, K.W.; Lecar, M.; Price, L.; Rubinstein, F.; Sezgen, O.; Wenzel, T.

1992-12-01

The US Department of Energy (DOE) has recognized the opportunity to achieve energy, economic, and environmental benefits by promoting energy-efficient lighting through federal policies, including lighting standards, financial incentives, and information programs. To assist in this process, the Office of Conservation and Renewable Energy's Office of Codes and Standards invited Lawrence Berkeley Laboratory to assess prospective national impacts for a variety of policy options. Some progress has already been made in developing lighting policies at both the federal and state levels. The US DOE's Office of Building Technologies has evaluated lighting efficiency incentives as part of its analysis for the National Energy Strategy. Fluorescent and incandescent lamp standards are included in the national Energy Policy Act of 1992 (P.L. 102-486, October 24, 1992). A few states have analyzed or implemented lamp and luminaire standards. Many policy-related issues merit further investigation. For example, there is considerable debate over issues such as mandatory or voluntary standards versus component labeling and other education-oriented strategies. Several different technologies are involved that interact with each other-lamps (incandescent, compact fluorescent, and HID), ballasts (for fluorescent and HID lamps), and fixtures with reflectors and lenses. Control systems and operation patterns must also be considered (timers, automated dimming, or occupancy sensors). Lighting applications are diverse, ranging from offices, restaurants, hallways, hospital operating rooms, to exterior lights. Lighting energy use influences heating and cooling requirements in buildings. Successful lighting system design must also address interactions between architectural design elements and daylighting availability. Proper system installation and ongoing operation and maintenance are crucial. The economic aspects of the preceding points must also be considered for policy making.

Analysis of federal policy options for improving US lighting energy efficiency: Commercial and residential buildings

Energy Technology Data Exchange (ETDEWEB)

Atkinson, B.A.; McMahon, J.E.; Mills, E.; Chan, P.; Chan, T.W.; Eto, J.H.; Jennings, J.D.; Koomey, J.G.; Lo, K.W.; Lecar, M.; Price, L.; Rubinstein, F.; Sezgen, O.; Wenzel, T.

1992-12-01

The US Department of Energy (DOE) has recognized the opportunity to achieve energy, economic, and environmental benefits by promoting energy-efficient lighting through federal policies, including lighting standards, financial incentives, and information programs. To assist in this process, the Office of Conservation and Renewable Energy`s Office of Codes and Standards invited Lawrence Berkeley Laboratory to assess prospective national impacts for a variety of policy options. Some progress has already been made in developing lighting policies at both the federal and state levels. The US DOE`s Office of Building Technologies has evaluated lighting efficiency incentives as part of its analysis for the National Energy Strategy. Fluorescent and incandescent lamp standards are included in the national Energy Policy Act of 1992 (P.L. 102-486, October 24, 1992). A few states have analyzed or implemented lamp and luminaire standards. Many policy-related issues merit further investigation. For example, there is considerable debate over issues such as mandatory or voluntary standards versus component labeling and other education-oriented strategies. Several different technologies are involved that interact with each other-lamps (incandescent, compact fluorescent, and HID), ballasts (for fluorescent and HID lamps), and fixtures with reflectors and lenses. Control systems and operation patterns must also be considered (timers, automated dimming, or occupancy sensors). Lighting applications are diverse, ranging from offices, restaurants, hallways, hospital operating rooms, to exterior lights. Lighting energy use influences heating and cooling requirements in buildings. Successful lighting system design must also address interactions between architectural design elements and daylighting availability. Proper system installation and ongoing operation and maintenance are crucial. The economic aspects of the preceding points must also be considered for policy making.

Distribution of E/N and N/e/ in a cross-flow electric discharge laser. [electric field to neutral gas density and electron number density

Science.gov (United States)

Dunning, J. W., Jr.; Lancashire, R. B.; Manista, E. J.

1976-01-01

Measurements have been conducted of the effect of the convection of ions and electrons on the discharge characteristics in a large scale laser. The results are presented for one particular distribution of ballast resistance. Values of electric field, current density, input power density, ratio of electric field to neutral gas density (E/N), and electron number density were calculated on the basis of measurements of the discharge properties. In a number of graphs, the E/N ratio, current density, power density, and electron density are plotted as a function of row number (downstream position) with total discharge current and gas velocity as parameters. From the dependence of the current distribution on the total current, it appears that the electron production in the first two rows significantly affects the current flowing in the succeeding rows.

Efficacy of pH elevation as a bactericidal strategy for treating ballast water of freight carriers

Directory of Open Access Journals (Sweden)

Clifford E. Starliper

2015-05-01

Full Text Available Treatment of ship ballast water with sodium hydroxide (NaOH is one method currently being developed to minimize the risk to introduce aquatic invasive species. The bactericidal capability of sodium hydroxide was determined for 148 bacterial strains from ballast water collected in 2009 and 2010 from the M/V Indiana Harbor, a bulk-freight carrier plying the Laurentian Great Lakes, USA. Primary culture of bacteria was done using brain heart infusion agar and a developmental medium. Strains were characterized based on PCR amplification and sequencing of a portion of the 16S rRNA gene. Sequence similarities (99+ % were determined by comparison with the National Center for Biotechnology Information (NCBI GenBank catalog. Flavobacterium spp. were the most prevalent bacteria characterized in 2009, comprising 51.1% (24/47 of the total, and Pseudomonas spp. (62/101; 61.4% and Brevundimonas spp. (22/101; 21.8% were the predominate bacteria recovered in 2010; together, comprising 83.2% (84/101 of the total. Testing was done in tryptic soy broth (TSB medium adjusted with 5 N NaOH. Growth of each strain was evaluated at pH 10.0, pH 11.0 and pH 12.0, and 4 h up to 72 h. The median cell count at 0 h for 148 cultures was 5.20 × 106 cfu/mL with a range 1.02 × 105–1.60 × 108 cfu/mL. The TSB adjusted to pH 10.0 and incubation for less than 24 h was bactericidal to 52 (35.1% strains. Growth in pH 11.0 TSB for less than 4 h was bactericidal to 131 (88.5% strains and pH 11.0 within 12 h was bactericidal to 141 (95.3%. One strain, Bacillus horikoshii, survived the harshest treatment, pH 12.0 for 72 h.

Efficacy of pH elevation as a bactericidal strategy for treating ballast water of freight carriers.

Science.gov (United States)

Starliper, Clifford E; Watten, Barnaby J; Iwanowicz, Deborah D; Green, Phyllis A; Bassett, Noel L; Adams, Cynthia R

2015-05-01

Treatment of ship ballast water with sodium hydroxide (NaOH) is one method currently being developed to minimize the risk to introduce aquatic invasive species. The bactericidal capability of sodium hydroxide was determined for 148 bacterial strains from ballast water collected in 2009 and 2010 from the M/V Indiana Harbor, a bulk-freight carrier plying the Laurentian Great Lakes, USA. Primary culture of bacteria was done using brain heart infusion agar and a developmental medium. Strains were characterized based on PCR amplification and sequencing of a portion of the 16S rRNA gene. Sequence similarities (99+ %) were determined by comparison with the National Center for Biotechnology Information (NCBI) GenBank catalog. Flavobacterium spp. were the most prevalent bacteria characterized in 2009, comprising 51.1% (24/47) of the total, and Pseudomonas spp. (62/101; 61.4%) and Brevundimonas spp. (22/101; 21.8%) were the predominate bacteria recovered in 2010; together, comprising 83.2% (84/101) of the total. Testing was done in tryptic soy broth (TSB) medium adjusted with 5 N NaOH. Growth of each strain was evaluated at pH 10.0, pH 11.0 and pH 12.0, and 4 h up to 72 h. The median cell count at 0 h for 148 cultures was 5.20 × 10(6) cfu/mL with a range 1.02 × 10(5)-1.60 × 10(8) cfu/mL. The TSB adjusted to pH 10.0 and incubation for less than 24 h was bactericidal to 52 (35.1%) strains. Growth in pH 11.0 TSB for less than 4 h was bactericidal to 131 (88.5%) strains and pH 11.0 within 12 h was bactericidal to 141 (95.3%). One strain, Bacillus horikoshii, survived the harshest treatment, pH 12.0 for 72 h.

Natural gas ballast requirement to allow participation of thermal plants in the new energy auctions: analysis and proposals; Requisito de lastro de gas natural para viabilizar a participacao de termeletricas nos leiloes de energia nova: analise e propostas

Energy Technology Data Exchange (ETDEWEB)

Avila, Pedro Luis de; Bezerra, Bernardo Vieira; Barroso, Luiz Augusto Nobrega; Pereira, Mario Veiga; Rosenblatt, Jose [PSR, Rio de Janeiro, RJ (Brazil)

2012-07-01

Since the first New Energy Auction (LEN), held in December 2005, there has been a continuous process of improving the auction rules and mechanism. For the specific case of gas-fired plants, a significant change was observed between the LEN A-3/2011 and LEN A-5/2011, and refers to the need of natural gas ballast for candidate projects in the auction. This rule was introduced by ANP Resolution No. 52, which establishes that the gas supply agreements must be backed up by proven reserves (analogous to the requirement in the power sector contracts of physical guarantee backup), and Ordinance MME No. 21/2008, which deals with power plants qualification for the new energy auctions. The latter was amended by MME Ordinance No. 514, which requires proven natural gas reserves to support the GSA of all candidate projects in a LEN. In other words, the gas supplier now has to prove that there are sufficient gas reserves to meet requirements of all candidate project in an auction, regardless of the plausibility of their engagement in the auction. In this context, the present study discusses these issues and has as main contributions: (I) a review of current regulations on contract ballast in the Brazilian natural gas sector, (II) a proposal to conciliate the need of fuel supply contract ballast to the dynamics of the natural gas sector, and (III) a proposal to conciliate the need for fuel contract ballast to the contracting process of the thermoelectric power in the new energy auctions. These contributions aim at a better integration between the sectors of natural gas and electricity in Brazil, leading to a more efficient use of resources and infrastructure development. (author)

Atomic gas temperature in a nonequilibrium high-intensity discharge lamp determined from the red wing of the resonance mercury line 254 nm

International Nuclear Information System (INIS)

Drakakis, E.; Karabourniotis, D.

2012-01-01

For developing low-wattage high intensity discharge (HID) lamps, a better understanding of the relatively unexplored nonequilibrium phenomena is essential. This needs interpretation of diagnostic results by methods free from equilibrium assumptions. In this paper, the atomic temperature is determined from the simulation of a quasistatic broadened resonance line by distinguishing between atomic temperature and excitation temperature in the equation of radiative transfer. The proposed method is applied to the red wing of the resonance mercury line 254 nm emitted from a HID lamp working on ac. The experimental results show severe deviation from local thermodynamic equilibrium. More than one thousand degrees difference was obtained between atomic and electron temperatures at the maximum current phase.

Atomic gas temperature in a nonequilibrium high-intensity discharge lamp determined from the red wing of the resonance mercury line 254 nm

Energy Technology Data Exchange (ETDEWEB)

Drakakis, E. [Technological Educational Institute, Department of Electrical Engineering, 71004 Heraklion (Greece); Karabourniotis, D. [Institute of Plasma Physics, Department of Physics, University of Crete, 71003 Heraklion (Greece)

2012-09-01

For developing low-wattage high intensity discharge (HID) lamps, a better understanding of the relatively unexplored nonequilibrium phenomena is essential. This needs interpretation of diagnostic results by methods free from equilibrium assumptions. In this paper, the atomic temperature is determined from the simulation of a quasistatic broadened resonance line by distinguishing between atomic temperature and excitation temperature in the equation of radiative transfer. The proposed method is applied to the red wing of the resonance mercury line 254 nm emitted from a HID lamp working on ac. The experimental results show severe deviation from local thermodynamic equilibrium. More than one thousand degrees difference was obtained between atomic and electron temperatures at the maximum current phase.

Offices, schools, trades, industries. A better lighting with mastered costs; Bureaux, ecoles, commerces, industries. Mieux s'eclairer a couts maitrises

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-07-01

Lighting costs in houses of offices represent 10 to 50% of the power consumption bill. This brochure presents some technical solutions for the reduction of lighting costs in office, public, commercial and industrial buildings. These solutions are based on the use of high performance fluorescent lamps and electronic ballasts for a 25% reduction of energy consumption and a 50% increase of lamps lifetime. High frequency ballasts eliminate the tiring blinking effect of classical 50 Hz ferromagnetic ballasts for a better visual comfort. Some elements for the calculation of lighting costs and savings are given. (J.S.)

Modeling the retention of rumen boluses for the electronic identification of goats.

Science.gov (United States)

Carné, S; Caja, G; Ghirardi, J J; Salama, A A K

2011-02-01

We constructed a regression model to estimate the retention of electronic boluses in goats. With this aim, 2,482 boluses were administered to goats from dairy (Murciano-Granadina, n=1,326; French Alpine, n=381) and meat (Blanca de Rasquera, n=532) breeds. A total of 19 bolus types made of materials (ceramic, plastic tubes filled with concrete or silicone, and ballasts) differing in their specific gravity (SG) were used, thereby obtaining a wide variation in bolus features: diameter (9 to 22 mm), length (37 to 84 mm), weight (5 to 111 g), volume (2.6 to 26 mL), and SG (1.0 to 5.5). Each bolus contained a half-duplex glass encapsulated transponder (32 × 3.8mm) and was administered using adapted balling guns. Murciano-Granadina and Blanca de Rasquera goats also wore 2 visual plastic ear tags: V1 (double flag, 5.1g) and V2 (flag-button, 4.2g). No data on ear tags in French Alpine goats was available. Bolus and ear tag retention [(retained/monitored) × 100] was recorded for at least 1 yr. Dynamic reading efficiency [(dynamic reading/static reading) × 100] was also evaluated from 1,496 bolus readings. No administration incidences or apparent negative behavior or performance effects were observed for any bolus type. Static reading efficiency of retained boluses was 100%, except for the prototypes with metal ballasts, which yielded a 93.3% reading efficiency. Retention of metal-ballasted boluses was confirmed using x-ray equipment. Excluding ballasted boluses, a 99.5% dynamic reading efficiency was obtained. Ear tag losses were 6.5% for V1 and 3.7% for V2, ranging from 3.2 to 7.8% depending on ear tag type and goat breed. Bolus retention varied (0 to 100%) according to their physical features. Obtained data allowed the fitting of a logistic model of bolus retention rate according to bolus volume and weight (R(2) = 0.98); the SG was implicitly considered. Estimated weight and SG to produce medium- (15 mL) and standard-sized (22 mL) boluses for 99.95% retention rate in

Comparative study of energy-efficiency and conservation systems for ceramic metal-halide discharge lamps

International Nuclear Information System (INIS)

Hermoso Orzáez, Manuel Jesús; Andrés Díaz, José Ramón de

2013-01-01

Interest in energy savings in urban lighting is gaining traction and has become a priority for municipal administrations. LED (light-emitting diode) technology appears to be the clear future lighting choice. However, this technology is still rapidly developing and has not been sufficiently tested. As an intermediate step, alternative proposals for energy-saving equipment for traditional discharge lamps are desirable so that the current technologies can coexist with the new LED counterparts for the short and medium term. This article provides a comparative study between two efficiency and energy-saving systems for discharge lamps with metal-halide and ceramic technologies, i.e., a lighting flow dimmer-stabilizer and a double-level electronic ballast. - Highlights: ► It has been demonstrated the possibility of regulating ceramic metal-halide lamps with lighting flow dimmer-stabilizer. ► Electronic ballasts can save approximately double quantity of energy than lighting flow dimmer-stabilizers. ► The use of lighting flow dimmer-stabilizer is more profitable than electronic ballasts due to costs and reliability

Laboratory evaluation of the emulsifying characteristics of pumps. [Bilge and ballast water oily wastes

Energy Technology Data Exchange (ETDEWEB)

Harvey, A.C.; Guzdar, A.R.; Fiswell, D.R.

1973-10-01

The program was devoted to a laboratory investigation of the emulsifying characteristics of different pumps suitable for shipboard pumping of bilge and ballast water oily wastes. The tests were designed to investigate the effect of several parameters, such as oil type, input oil concentration, detergent, pump operating characteristics (pressure and flow rate), and salt versus fresh water, on emulsification. Tests were conducted on the Foster-Miller tests loop. No. 2 fuel oil, lubricating oil and No. 6 fuel oil were the oils tested at concentrations ranging from 1 to 10%. The oils were tested with and without the addition of 10% Gamlen D surfactant. The pumps used were a Parker Diaphragm pump, a Blackmer Sliding Vane pump, an Ingersoll Rand Centrifugal pump and a Deming Centrifugal pump. Pump pressure ranged from 10 to 60 psi and flow rate from 10 to 100 gpm. A total of 270 tests were conducted covering 198 different operating points, 108 concerning pump comparison, 54 concerning oil concentration and surfactant, and 45 concerning salt water.

Stress-based Variable-inductor for Electronic Ballasts

DEFF Research Database (Denmark)

Zhang, Lihui; Xia, Yongming; Lu, Kaiyuan

2015-01-01

Current-controlled variable inductors adjust the inductance of an alternating current (ac) coil by applying a controlled dc current to saturate the iron cores of the ac coil. The controlled dc current has to be maintained during operation, which results in increased power losses. This paper prese......-based variable inductor concept is validated using a 3-D finite-element analysis. A prototype was manufactured, and the experimental results are presented. A linear relationship between inductance and applied stress can be achieved.......Current-controlled variable inductors adjust the inductance of an alternating current (ac) coil by applying a controlled dc current to saturate the iron cores of the ac coil. The controlled dc current has to be maintained during operation, which results in increased power losses. This paper...... presents a new stress-based variable inductor to control inductance using the inverse magnetostrictive effect of a magnetostrictive material. The stress can be applied by a piezoelectrical material, and thus a voltage-controlled variable inductor can be realized with zero-power consumption. The new stress...

Flicker licker

Energy Technology Data Exchange (ETDEWEB)

Dooley, T.

1988-02-24

Discusses the use of high frequency (h.f.) electronic ballasts to control fluorescent lighting. H.F. ballasts consume about 25% less power than conventional, switch-start control gear to produce the same light intensity. They eliminate stuttering starts and, according to a recent report, halve the number of headaches caused by lamps operating on a conventional 50Hz supply. H.F. ballasts are also smaller, lighter and have fewer parts than conventional ballasts, but they are more expensive. The high power factor in h.f. lighting gives two further advantages - one is lower demand on the building's ventilation system because the lamps produce less heat. Another benefit from low power consumption is an increase in a lamp's useful life. It is estimated that 2 years is a realistic payback on h.f. lighting in offices where lights are on about 12 hours per day. Sales in h.f. ballasts are now beginning to accelerate. There is a consensus between manufacturers to make their ballasts compatible with a range of fluorescent lamps. The exception is Phillips, who have chosen an argon lamp specially designed for use with its h.f. ballast. Their strategy is based on dimmer control - argon lamps are easier to dim smoothly than krypton lamps. Dimming allows adjustment of light levels to suit a given job and can also be used as part of an energy management system to dim or raise the lighting levels according to conditions.

Note: Measuring breakdown characteristics during the hot re-ignition of high intensity discharge lamps using high frequency alternating current voltage.

Science.gov (United States)

van den Bos, R A J M; Sobota, A; Manders, F; Kroesen, G M W

2013-04-01

To investigate the cold and hot re-ignition properties of High Intensity Discharge (HID) lamps in more detail an automated setup was designed in such a way that HID lamps of various sizes and under different background pressures can be tested. The HID lamps are ignited with a ramped sinusoidal voltage signal with frequencies between 60 and 220 kHz and with amplitude up to 7.5 kV. Some initial results of voltage and current measurements on a commercially available HID lamp during hot and cold re-ignition are presented.

Levantamento florístico das macroalgas da baía de Sepetiba e adjacências, RJ: ponto de partida para o Programa GloBallast no Brasil Floristic survey of the macroalgae from Sepetiba bay and surrounding area, Rio de Janeiro State: starting point for the GloBallast Programme in Brazil

Directory of Open Access Journals (Sweden)

Maria Teresa Menezes de Széchy

2005-09-01

Full Text Available O Porto de Sepetiba, Estado do Rio de Janeiro, foi escolhido, no Brasil, como área-piloto do projeto "Remoção de barreiras para a implementação efetiva do controle de água de lastro e medidas de gestão em países em desenvolvimento" (Programa GloBallast. Para possibilitar comparações, os seis países participantes do Programa GloBallast foram orientados a adotar a mesma metodologia para o levantamento preliminar da biota das áreas-pilotos valorizando a identificação em nível de espécie. O presente estudo teve como objetivo aplicar metodologia estabelecida pelo Centro para Pesquisa sobre Espécies Marinhas Introduzidas, da Austrália (Procedimento CRIMP, com algumas adaptações, no levantamento florístico das macroalgas de substratos consolidados naturais da área-piloto do Porto de Sepetiba. Coletas de macroalgas foram realizadas em novembro/2001, em nove locais da baía de Sepetiba e adjacências, desde a franja da região sublitorânea até cerca de -4 m de profundidade. Em cada local, seis quadrados de 0,1 m² de área foram raspados. O material foi depositado no Herbário do Instituto de Pesquisas Jardim Botânico do Rio de Janeiro (RB. Das 96 espécies identificadas (20 Chlorophyta, 16 Phaeophyta, 60 Rhodophyta, 12 não haviam sido citadas anteriormente para a área de estudo. Cladophora pellucidoidea C. Hoek, Coelothrix irregularis (Harv. Boergesen e Acrochaetium savianum (Menegh. Nägeli são ocorrências novas para o Estado. Não há indícios de que as novas ocorrências equivalem a espécies recentemente introduzidas por meio das atividades portuárias. O procedimento metodológico adotado mostrou-se eficiente, resultando em listagem de espécies comparável às de levantamentos florísticos com maior esforço amostral e complementando os dados pretéritos existentes para a baía de Sepetiba e adjacências. No entanto, ressalta-se a importância de uma reavaliação das escalas temporal e espacial da estratégia de

[MVK gene abnormality and new approach to treatment of hyper IgD syndrome and periodic fever syndrome].

Science.gov (United States)

Naruto, Takuya

2007-04-01

Hyper IgD and periodic fever syndrome (HIDS; OMIM 260920) is one of the hereditary autoinflammatory syndromes characterized by recurrent episodes of fever and inflammation.. HIDS is an autosomal recessive disorder characterized by recurrent fever attacks in early childhood. HIDS caused by mevalonate kinase (MK) mutations, also that is the gene of mevalonic aciduria (OMIM 251170). During febrile episodes, urinary mevalonate concentrations were found to be significantly elevated in patients. Diagnosis of HIDS was retrieving gene or measurement of the enzyme activity in peripheral blood lymphocyte in general. This of HIDS is an activity decline of MK, and a complete deficiency of MK becomes a mevalonic aciduria with a nervous symptom. The relation between the fever and inflammation of mevalonate or isoprenoid products are uncertain. The therapy attempt with statins, which is inhibited the next enzyme after HMG-CoA reductase, or inhibit the proinflammatory cytokines.

Investigation of hydrometeor classification uncertainties through the POLARRIS polarimetric radar simulator

Science.gov (United States)

Dolan, B.; Rutledge, S. A.; Barnum, J. I.; Matsui, T.; Tao, W. K.; Iguchi, T.

2017-12-01

POLarimetric Radar Retrieval and Instrument Simulator (POLARRIS) is a framework that has been developed to simulate radar observations from cloud resolving model (CRM) output and subject model data and observations to the same retrievals, analysis and visualization. This framework not only enables validation of bulk microphysical model simulated properties, but also offers an opportunity to study the uncertainties associated with retrievals such as hydrometeor classification (HID). For the CSU HID, membership beta functions (MBFs) are built using a set of simulations with realistic microphysical assumptions about axis ratio, density, canting angles, size distributions for each of ten hydrometeor species. These assumptions are tested using POLARRIS to understand their influence on the resulting simulated polarimetric data and final HID classification. Several of these parameters (density, size distributions) are set by the model microphysics, and therefore the specific assumptions of axis ratio and canting angle are carefully studied. Through these sensitivity studies, we hope to be able to provide uncertainties in retrieved polarimetric variables and HID as applied to CRM output. HID retrievals assign a classification to each point by determining the highest score, thereby identifying the dominant hydrometeor type within a volume. However, in nature, there is rarely just one a single hydrometeor type at a particular point. Models allow for mixing ratios of different hydrometeors within a grid point. We use the mixing ratios from CRM output in concert with the HID scores and classifications to understand how the HID algorithm can provide information about mixtures within a volume, as well as calculate a confidence in the classifications. We leverage the POLARRIS framework to additionally probe radar wavelength differences toward the possibility of a multi-wavelength HID which could utilize the strengths of different wavelengths to improve HID classifications. With

Time resolved Thomson scattering measurements on a high pressure mercury lamp

International Nuclear Information System (INIS)

Vries, N de; Zhu, X; Kieft, E R; Mullen, J van der

2005-01-01

Time resolved Thomson scattering (TS) measurements have been performed on an ac driven high pressure mercury lamp. For this high intensity discharge (HID) lamp, TS is coherent and a coherent fitting routine, including rotational Raman calibration, was used to determine n e and T e from the measured spectrum. The maximum electron density and electron temperature obtained in the centre of the discharge varied in a time period of 5 ms between 1 x 10 21 m -3 e 21 m -3 and 6500 K e < 7100 K. In order to test the non-intrusive character of TS, we have derived a general expression for the heating of the electrons. By applying this to our mercury lamp and laser settings, we have confirmed the non-intrusiveness of our method. This is supported by the experimental findings. Furthermore, because the TS results were obtained directly, thus, without the local thermodynamic equilibrium (LTE) assumptions, they enabled us to follow the deviations from LTE as a function of time. Contrary to the generally made assumption that HID lamps are in LTE, we have found deviations from both the thermal and chemical equilibrium inside the high pressure mercury lamp at different phases of the applied current

Light and Light Sources High-Intensity Discharge Lamps

CERN Document Server

Flesch, Peter G

2006-01-01

Light and Light Sources gives an introduction to the working principles of high-intensity discharge (HID) lamps and points out challenges and problems associated with the development and operation of HID lamps. The state-of-the-art in electrode and plasma diagnostics as well as numerical methods used for the understanding of HID lamps are described. This volume addresses students as well as scientists and researchers at universities and in industry.

Performance comparison of direct and indirect lighting systems

International Nuclear Information System (INIS)

Rubinstein, F.; Morse, O.; Clark, T.

1993-01-01

The performance of a retrofitted indirect lighting system was compared to the performance of a typical de-lamped direct lighting system in a partitioned office space. Power, illuminance and luminance measurements were made for the de-lamped direct lighting system and after installation of the indirect lighting system with various lamp and ballast combinations. Using the same lamps and ballasts, average workplace illuminance was slightly higher with indirect lighting than with direct lighting. With indirect lighting, workplace lumen efficacy was 4.5% lower due to the higher power draw of the lamps in the more open and cooler indirect fixtures. Indirect lighting with 36 watt T-8 lamps and electronic ballasts achieved an initial average workplace illuminance of 45 foot-candles in the partitioned office space at only 1.1 w/ft 2

Ballast Load Control of Turbine-Generator Sets in the Micro-Hydro Range with a Turbine that has no Flow Regulating Value

Directory of Open Access Journals (Sweden)

Valentin Nedelea

2011-09-01

Full Text Available This paper presents the effects of voltage and frequency variation on users load supplies from electrical supply system generated from small micro-hydro plants. Induction generators operate as stand-alone self excited by capacitors and turbine has no flow regulating valve. Many conventional and non conventional approaches are described to govern turbine-generator set to ensure a steady frequency and voltage level. A load controller increases or decreases a ballast load connected across the generator as the user load varies, to keep frequency and voltage variation in standard limits. To design a controller for self excited induction generator, researches were performed on asynchronous generator with double winding stator to analyse steady state open loop behaviour. The results on the behaviour of the unregulated turbine (DC motor – generator system was presented.

First results of Chinese particle instruments in the Double Star Program

Directory of Open Access Journals (Sweden)

J. B. Cao

2005-11-01

Full Text Available Double Star Program (DSP aims to investigate the trigger mechanism and physical models of geomagnetic storms and substorms. The DSP involves two satellites: the equatorial satellite of DSP (TC-1 in China and the polar satellite of DSP (TC-2 in China. On board the two satellites of TC-1 and TC-2, there are four kinds of particle instruments developed by the Center for Space Science and Applied Research (CSSAR, namely: the High Energy Electron Detector (HEED, TC-1, 2, the High Energy Proton Detector (HEPD, TC-1, 2, the High Energy Heavy Ion Detector (HID, TC-1, 2 and the Low Energy Ion Detector (LEID, TC-2. HEED, HEPD and HID were developed and calibrated in China. The LEID was developed in China and calibrated in France. This paper introduces the scientific objectives and characteristics of each instrument, their status and some preliminary results.

Single-stage unity power factor based electronic ballast

Indian Academy of Sciences (India)

Ashish Shrivastava

This paper deals with the design, modeling, analysis and implementation of .... wave voltage which was fed to the load through an LC network ..... 18 and 19 show simulated results which are discussed as follows. g. D. S powergui. Discrete ,.

Process for environmentally safe disposal of used fluorescent lamp potted ballast assemblies with component part reclamation and/or recycling

Energy Technology Data Exchange (ETDEWEB)

Nardella, A.; Norian, B.

1993-07-27

A process is described for the environmentally safe and economical disposal of used fluorescent lamp potted ballast housing assemblies comprising removing from the housing the potted assembly with its embedded electrical component assemblies including a component capacitor containing environmentally hazardous material PCB's; after or before such removing, immersing the potted assembly in a cryogenic bath and freezing the same to reader the potting sufficiently brittle to fragment into small pieces upon being impacted; impacting the potting thoroughly to crush and fragment the same into small pieces and to cleanly remove substantially all traces of the potting from all the electrical components and parts embedded therein and without imparting damage to the components and parts; disconnecting the component containing the environmentally hazardous material; and incinerating only the component containing the environmentally hazardous material, leaving all other components and parts including the housing and potting fragments for salvage, re-use and/or recycling.

Comparison of outcomes in hematological malignancies treated with haploidentical or HLA-identical sibling hematopoietic stem cell transplantation following myeloablative conditioning: A meta-analysis

Science.gov (United States)

Guo, Dan; Xu, Peipei; Chen, Bing

2018-01-01

Purpose Haploidentical and human leukocyte antigen (HLA)-identical sibling hematopoietic stem transplantation are two main ways used in allogeneic hematopoietic stem cell transplantation (allo-HSCT). In recent years, remarkable progress has been made in haploidentical allo-HSCT (HID-SCT), and some institutions found HID-SCT had similar outcomes as HLA-identical sibling allo-HSCT (ISD-SCT). To clarify if HID-SCT has equal effects to ISD-SCT in hematologic malignancies, we performed this meta-analysis. Methods Relevant articles published prior to February 2017 were searched on PubMed. Two reviewers assessed the quality of the included studies and extracted data independently. Odds ratio (OR) and 95% confidence intervals (CIs) were calculated for statistical analysis. Results Seven studies including 1919 patients were included. The rate of platelet engraftment is significantly lower after HID-SCT versus ISD-SCT while there is no difference in neutrophil engraftment (OR = 2.58, 95% CI = 1.70–3.93, P SCT versus ISD-SCT (OR = 1.88, 95% CI = 1.42–2.49, P SCT group (OR = 0.70, 95% CI = 0.55–0.90, P = 0.005). The incidence rates of overall survival (OS) and disease-free-survival/leukemia-free survival/relapse-free survival (DFS/LFS/RFS) after ISD-SCT are all significantly superior to HID-SCT (OR = 1.32, 95% CI = 1.08–1.62, P = 0.006; OR = 1.25, 95% CI = 1.03–1.52, P = 0.02). There is no significant difference in transplantation related mortality (TRM) rate after HID-SCT and ISD-SCT. Conclusion After myeloablative conditioning, patients receiving ISD-SCT have a faster engraftment, lower acute GVHD and longer life expectancy compared to HID-SCT with GVHD prophylaxis (cyclosporine A, methotrexate, mycophenolate mofetil and antithymoglobulin; CsA + MTX + MMF + ATG). Currently, HID-SCT with GVHD prophylaxis (CsA + MTX + MMF + ATG) may not replace ISD-SCT when HLA-identical sibling donor available. PMID:29381772

ECDIS Possibilities for BWE Adoption

Directory of Open Access Journals (Sweden)

Srdjan ŽuŁkin

2017-09-01

Full Text Available The Electronic Chart Display and Information System (ECDIS development and implementation have been linked primarily to the safety of navigation. Further development allows the implementation from other aspects of navigation. This primarily pertains to the Harmful Aquatic Organisms and Pathogens (HAOP from Ballast Water Exchange (BWE and the use of ECDIS system for improving environmental protection. The paper contains an overview of important legal aspects of sea environment protection related to the Ballast Water Management (BWM Convention on global as well as on local scale. Apart from enhancing the safety of navigation, integration of the proposed tool for sea environment protection in the ECDIS with onboard ballast water system can significantly contribute to sea and sea environment protection from harmful substances. In this paper, the architecture of such system is suggested. This approach also ensures a reduction of possible consequences on ecological incidents and human errors.

The occurrence of pathogenic bacteria in some ships' ballast water incoming from various marine regions to the Sea of Marmara, Turkey.

Science.gov (United States)

Altug, Gulsen; Gurun, Sevan; Cardak, Mine; Ciftci, Pelin S; Kalkan, Samet

2012-10-01

The composition and frequency of antibiotic resistance of pathogenic bacteria, the abundance of heterotrophic aerobic bacteria (HPC) and possible in-situ use of chromogenic agar were investigated in the ships' ballast water coming from different regions of the world to the Sea of Marmara, Turkey for the first time. The samples that were taken from 21 unit ships coming from various marine environments of the Southern China Sea, the Atlantic Ocean, the Mediterranean and the Black Sea to the Sea of Marmara, Turkey in 2009 and 2010 were tested. 38 bacteria species, 27 of them pathogenic bacteria belonging to 17 familia, were detected. Vibrio cholera was not detected in the samples. However, the presence of a high number of HPC, including a cocktail of pathogenic bacteria showed that the ships carry a potential risk for the Sea of Marmara. Copyright © 2012 Elsevier Ltd. All rights reserved.

Instant OSSEC host-based intrusion detection system

CERN Document Server

Lhotsky, Brad

2013-01-01

Filled with practical, step-by-step instructions and clear explanations for the most important and useful tasks. A fast-paced, practical guide to OSSEC-HIDS that will help you solve host-based security problems.This book is great for anyone concerned about the security of their servers-whether you are a system administrator, programmer, or security analyst, this book will provide you with tips to better utilize OSSEC-HIDS. Whether you're new to OSSEC-HIDS or a seasoned veteran, you'll find something in this book you can apply today!This book assumes some knowledge of basic security concepts an

Spectroscopy on metal-halide lamps under varying gravity conditions

NARCIS (Netherlands)

Flikweert, A.J.

2008-01-01

Worldwide, 20% of all electricity is used for lighting. For this reason, efficient lamps are economically and ecologically important. High intensity discharge (HID) lamps are efficient lamps. The most common HID lamp these days is the metal-halide (MH) lamp. MH lamps have a good colour rendering

A 48-plex autosomal SNP GenPlex™ assay for human individualization and relationship testing

DEFF Research Database (Denmark)

Tomas Mas, Carmen; Børsting, Claus; Morling, Niels

2012-01-01

SNPs are being increasingly used by forensic laboratories. Different platforms have been developed for SNP typing. We describe the GenPlex™ HID system protocol, a new SNP-typing platform developed by Applied Biosystems where 48 of the 52 SNPforID SNPs and amelogenin are included. The GenPlex™ HID...

The advanced EctoSys electrolysis as an integral part of a ballast water treatment system.

Science.gov (United States)

Echardt, J; Kornmueller, A

2009-01-01

A full-scale 500 m(3)/h ballast water treatment system was tested according to the landbased type approval procedure of the International Maritime Organization (IMO). The system consists of disc filters followed by the advanced EctoSys electrolysis as an integral part for disinfection. The test water quality exceeded by far the minimum requirements for type approval testing. Due to the properties of the special electrodes used together with the striking disinfection effect, the disinfectants assumed to be produced inline by the EctoSys cell in river water were hydroxyl radicals, while in brackish water additionally chlorine and consequently the more stable bromine were formed. In river water, no residual oxidants could be detected in accordance with the assumed production of not responding, highly-reactive and short-living hydroxyl radicals. Accordingly, disinfection byproduct (DBP) formation was very low and close to the limit of quantification in river water. While in brackish water, initial residual oxidant concentrations were maximum 2 mg/L as chlorine and mostly brominated DBP (especially bromoform and bromate) were found. Overall considering this worst case test approach, the DBP concentrations of the treated effluents were below or in the range of the WHO Drinking Water Guideline values and therefore evaluated as acceptable for discharge to the environment. The stringent discharge standard by IMO concerning viable organisms was fully met in river and brackish water, proving the disinfection efficiency of the EctoSys electrolysis against smaller plankton and bacteria.

THE DETERMINATION OF THE BALLAST RESISTANCE USED FOR THE CONECTION TO AN EXPERIMENTAL STAND FOR THE STUDY OF THE HYDRO – WIND HYBRIYD POWER (CHHE

Directory of Open Access Journals (Sweden)

JOIAN R.

2015-09-01

Full Text Available This paper point out some of the experimental determinations that must be made in the achieving of a hidro - wind hybrid system. It highlights the design and implementation of a1 kW ballast resistor and 48 V nickel-chromium wire, with the diameter of 60 three millimeters and connecting cable at the wind turbine by electric panel. Thus, this experimental stand CHHE includes a wind turbine 1 kW, placed on the roof of the Technical University of Cluj Napoca (this place is favorable because the wind has high speeds at great height and hydro turbine type Pelton 1 kW power. The experimental stand for the study of CHHE hybrid energy system will allow the determination of more experimental conclusive on the impact of the achievement of an energy balance of the physical model.

[Expression of receptors of estrogens and androgens in the testicular appendices].

Science.gov (United States)

Paredes Esteban, R M; Luque Barona, R J; Velasco Sánchez, B; Rodríguez Vargas, J; Lorite, A; García Ruiz, M

2008-07-01

The appendices or hidátides of the testicle are structures that are considered an embryonic rest. In testicular hidátide estrogen receivers have been demonstrated but in the epididimys the results vary. Has been theorized that the elevation of the estrogen levels in the puberty can produce an inflammation and torsion of hidátide, nevertheless, in the epididimys in which the estrogen expression is not clear (and also they are twisted) the theory is put in doubt. This controversy takes us to the accomplishment of this work. A prospective study is made in 20 testicular appendices, of which 7 from the epididimys are extirpated of patients to whom an escrotal exploration is made in the development of surgery of processes of the inguino-escrotal channel (hidroceles, hernias). Optical microscopy and inmunohistoquímical study are analyzed by means of using prediluted monoclonales antibodies, for receivers of estrogens, androgens and proliferative index. The results were proceed and analyzed by means of SPSS statistical program. All hidátides, testicular and from the epididimarys expressed receivers for estrogens without significant difference among them, not existing differences as far as the location of receiving sayings within the three compartments of hidátide. The number of estrogen receivers was in relation to the age of the patient. Only hidátides from the epididimys fundamentally expressed receivers of located androgens and at level of ductus. We have not found significant relation between the proliferative index and the expression of estrogen receivers. The proliferative index was more elevated at level of ductus. 1) As much the testicular appendices as those from the epididimays expressed receivers of estrogens at level of the three compartments. It makes think about a same embryonic origin, although only the epididimal ones expressed androgen receivers. 2) the observation of estrogen receivers in both types of hidátides, as well as the relation of the

Investigation of acoustic resonances in high-power lamps

International Nuclear Information System (INIS)

Kettlitz, M; Zalach, J; Rarbach, J

2011-01-01

High-power, medium-pressure, mercury-containing lamps are used as UV sources for many industrial applications. Lamps investigated in this paper are driven with an electronic ballast with a non-sinusoidal current waveform at a fixed frequency of 20 kHz and a maximum power output of 35 kW. Instabilities can occur if the input power is reduced below 50%. The reason is identified as acoustic resonances in the lamp. Comparison of calculated and measured resonance frequencies shows a good agreement and explains the observed lamp behaviour. This has led to the development of a new ballast prototype which is able to avoid instabilities by changing the driving frequency dependent on the applied power.

Mevalonate kinase deficiencies: from mevalonic aciduria to hyperimmunoglobulinemia D syndrome

Directory of Open Access Journals (Sweden)

Hoffmann Georg F

2006-04-01

Full Text Available Abstract Mevalonic aciduria (MVA and hyperimmunoglobulinemia D syndrome (HIDS represent the two ends of a clinical spectrum of disease caused by deficiency of mevalonate kinase (MVK, the first committed enzyme of cholesterol biosynthesis. At least 30 patients with MVA and 180 patients with HIDS have been reported worldwide. MVA is characterized by psychomotor retardation, failure to thrive, progressive cerebellar ataxia, dysmorphic features, progressive visual impairment and recurrent febrile crises. The febrile episodes are commonly accompanied by hepatosplenomegaly, lymphadenopathy, abdominal symptoms, arthralgia and skin rashes. Life expectancy is often compromised. In HIDS, only febrile attacks are present, but a subgroup of patients may also develop neurological abnormalities of varying degree such as mental retardation, ataxia, ocular symptoms and epilepsy. A reduced activity of MVK and pathogenic mutations in the MVK gene have been demonstrated as the common genetic basis in both disorders. In MVA, the diagnosis is established by detection of highly elevated levels of mevalonic acid excreted in urine. Increased levels of immunoglobulin D (IgD and, in most patients of immunoglobulin A (IgA, in combination with enhanced excretion of mevalonic acid provide strong evidence for HIDS. The diagnosis is confirmed by low activity of mevalonate kinase or by demonstration of disease-causing mutations. Genetic counseling should be offered to families at risk. There is no established successful treatment for MVA. Simvastatin, an inhibitor of HMG-CoA reductase, and anakinra have been shown to have beneficial effect in HIDS.

Sadhana | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Sadhana. BHIM SINGH. Articles written in Sadhana. Volume 41 Issue 10 October 2016 pp 1111-1122. Single-stage unity power factor based electronic ballast · ASHISH SHRIVASTAVA BHIM SINGH · More Details Abstract Fulltext PDF. This paper deals with the design, modeling, analysis and ...

Prophylactic anti-D preparations display variable decreases in Fc-fucosylation of anti-D.

Science.gov (United States)

Kapur, Rick; Della Valle, Luciana; Verhagen, Onno J H M; Hipgrave Ederveen, Agnes; Ligthart, Peter; de Haas, Masja; Kumpel, Belinda; Wuhrer, Manfred; van der Schoot, C Ellen; Vidarsson, Gestur

2015-03-01

RhIG is obtained from hyperimmunized healthy anti-D donors (HIDs) boosted with D+ red blood cells (RBCs). One hypothesis for its mechanism of action is fast clearance of opsonized D+ RBCs through Fcγ receptor (FcγR)III. Levels of immunoglobulin (Ig)G Fc-fucosylation influence interactions with FcγRIII, with less Fc-fucosylation strengthening the interaction. Anti-D IgG1 Fc-glycosylation patterns in 93 plasma samples from 28 male and 28 female Dutch HIDs and RhIG were analyzed with mass spectrometry. The Fc-glycosylation profiles of HIDs were evaluated with regard to their immunization history. HID sera demonstrated clearly lowered anti-D Fc-fucosylation compared to normal IgG fucosylation (93%); this was more pronounced for female than for male HIDs (47% vs. 65%, p = 0.001). RhIG preparations from seven manufacturers varied greatly in the level of Fc-fucosylation (56%-91%). The level of fucosylation slightly increased upon repeated immunization, although it remained fairly constant over time. The RhIG from the different manufacturers all demonstrated increased Fc-galactosylation (64%-82%) compared to total IgG (38%-51%). RhIG preparations vary in Fc-fucosylation and all demonstrate increased galactosylation. Despite not knowing the exact working mechanism, immunoprophylaxis could perhaps be optimized by selection of donors whose anti-D have low amounts of Fc-fucose, to increase the clearance activity of anti-D preparations, as well as high amounts of galactosylation, for anti-inflammatory effects. Implementing a biologic assay in the standardization of RhIG preparations might be considered. © 2014 AABB.

Impact analyses for negative flexural responses (hogging) in railway prestressed concrete sleepers

International Nuclear Information System (INIS)

Kaewunruen, S; Ishida, T; Remennikov, AM

2016-01-01

By nature, ballast interacts with railway concrete sleepers in order to provide bearing support to track system. Most train-track dynamic models do not consider the degradation of ballast over time. In fact, the ballast degradation causes differential settlement and impact forces acting on partial and unsupported tracks. Furthermore, localised ballast breakages underneath railseat increase the likelihood of centrebound cracks in concrete sleepers due to the unbalanced support under sleepers. This paper presents a dynamic finite element model of a standard-gauge concrete sleeper in a track system, taking into account the tensionless nature of ballast support. The finite element model was calibrated using static and dynamic responses in the past. In this paper, the effects of centre-bound ballast support on the impact behaviours of sleepers are highlighted. In addition, it is the first to demonstrate the dynamic effects of sleeper length on the dynamic design deficiency in concrete sleepers. The outcome of this study will benefit the rail maintenance criteria of track resurfacing in order to restore ballast profile and appropriate sleeper/ballast interaction. (paper)

Impact analyses for negative flexural responses (hogging) in railway prestressed concrete sleepers

Science.gov (United States)

Kaewunruen, S.; Ishida, T.; Remennikov, AM

2016-09-01

By nature, ballast interacts with railway concrete sleepers in order to provide bearing support to track system. Most train-track dynamic models do not consider the degradation of ballast over time. In fact, the ballast degradation causes differential settlement and impact forces acting on partial and unsupported tracks. Furthermore, localised ballast breakages underneath railseat increase the likelihood of centrebound cracks in concrete sleepers due to the unbalanced support under sleepers. This paper presents a dynamic finite element model of a standard-gauge concrete sleeper in a track system, taking into account the tensionless nature of ballast support. The finite element model was calibrated using static and dynamic responses in the past. In this paper, the effects of centre-bound ballast support on the impact behaviours of sleepers are highlighted. In addition, it is the first to demonstrate the dynamic effects of sleeper length on the dynamic design deficiency in concrete sleepers. The outcome of this study will benefit the rail maintenance criteria of track resurfacing in order to restore ballast profile and appropriate sleeper/ballast interaction.

On the square arc voltage waveform model in magnetic discharge lamp studies

OpenAIRE

Molina, Julio; Sainz Sapera, Luis; Mesas García, Juan José

2011-01-01

The current number of magnetic and electronic ballast discharge lamps in power distribution systems is increasing because they perform better than incandescent lamps. This paper studies the magnetic discharge lamp modeling. In particular, the arc voltage waveform is analyzed and the limitations of the square waveform model are revealed from experimental measurements.

Treatment of heavy metal polluted industrial wastewater by a new water treatment process: ballasted electroflocculation.

Science.gov (United States)

Brahmi, Khaled; Bouguerra, Wided; Harbi, Soumaya; Elaloui, Elimame; Loungou, Mouna; Hamrouni, Béchir

2018-02-15

This laboratory study investigated the parameters efficiency of the new technology: ballasted electro-flocculation (BEF) using aluminum (Al) electrodes to remove cadmium and zinc from industrial mining wastewater (MWW). The principle of the BEF process is based on the use of micro-sand and polymer together to increase the weight of the flocs and the rate at which they settle is radically changing the electrocoagulation-electroflocculation settling methodology. Based on the examination of the operation parameters one by one, the best removal percentage was obtained at a current intensity of 2A, a the flow rate of 20L/h, a micro-sand dose of 6g/L, a polyéthylèneimine (PEI) polymer dose of 100mg, the contact times of 30min, a stirring speed of 50 RPM, a monopolar configuration of the electrodes, and an electrodes number of 10. The results showed that the flow rate and the current density have a preponderant effect on the variability of the quality of the settled water. In comparison, filterability was found to be more sensitive to number of electrodes, micro sand dosages and current density. It was dependent on the ratio of microsand to PEI polymer dosage, and improved when this ratio increased. Response surface methodology was applied to evaluate the main effects and interactions among stirring speed, polymer dose, current intensity, and electrodes number. The removal of Cd and Zn from industrial MWW was done for very low cost of 0.1TND/m 3 equivalent to 0.04€/m 3 . The investigation of BEF process proposes a highly cost-effective wastewater treatment method if compared to Actiflo TM and electrocoagulation. Copyright © 2017 Elsevier B.V. All rights reserved.

Effect of material parameters on the compactibility of backfill materials

International Nuclear Information System (INIS)

Keto, P.; Kuula-Vaeisaenen, P.; Ruuskanen, J.

2006-05-01

The effect of different parameters on compactibility of mixture of bentonite and ballast as well as Friedland-clay was studied in laboratory with two different types of compaction tests. The material parameters varied were grain size distribution of the ballast material, grain shape, water ratio and bentonite content (15/30%). The other parameters varied were salinity of the mixing water, mixing process and compaction method and energy. Ballast materials with varying grain size distributions were produced from Olkiluoto mica-gneiss with different type of crushing processes. In addition, sand was chosen for ballast material due to its uniform grain size distribution and rounded grain shape. The maximum grain size of the ballast materials was between 5-10 mm. When comparing the compactibility of ballast materials, the highest dry densities were gained for ballast materials with graded grain size distribution. The compaction behaviour of the tested bentonite ballast mixtures is dominated by the bentonite content. The other parameters varied did not have significant effect on the compactibility of the mixtures with bentonite content of 30%. This can be explained with the amount of bentonite that is higher than what is needed to fill up the volume between the ballast grains. The results gained with the two different compaction tests are comparable. Both the bentonite/ballast mixtures and the Friedland clay behaved similarly when compacted with three different compaction pressures (180, 540 and 980 kPa). (orig.)

Mercury-free high pressure discharge lamps dominated by molecular radiation

International Nuclear Information System (INIS)

Kaening, M; Hitzschke, L; Berger, M; Schalk, B; Franke, St; Methling, R

2011-01-01

High intensity discharge (HID) lamps dominated by molecular radiation offer a very promising alternative for use in future light sources. They are able to deliver competitive efficacies of about 110 lm W -1 and higher, excellent colour rendering index above 90 and a correlated colour temperature in the 3000-4000 K region at the operating point near the Planckian locus. Moreover, these lamps are opening up the possibility of dimming. Due to the fact that they are able to omit mercury they are environmentally friendly. The emission spectra generated by these HID lamps differ significantly from those of conventional lamps. The reason for this is the dominance of molecular radiation processes. In comparison with conventional HID lamps atomic contributions are usually rather small. In the present case they amount to less than about 10% of the total intensity in the visible range.

Mercury-free high pressure discharge lamps dominated by molecular radiation

Energy Technology Data Exchange (ETDEWEB)

Kaening, M; Hitzschke, L; Berger, M [Research Europe, OSRAM GmbH, Werner-von-Siemens Strasse 6, 86159 Augsburg (Germany); Schalk, B [Vitec Group Videocom Division, Erfurter Strasse 16, 85386 Eching (Germany); Franke, St; Methling, R, E-mail: m.kaening@osram.de [INP, Leibniz-Institut fuer Plasmaforschung und Technologie e. V., Felix-Hausdorff-Strasse 2, 17489 Greifswald (Germany)

2011-06-08

High intensity discharge (HID) lamps dominated by molecular radiation offer a very promising alternative for use in future light sources. They are able to deliver competitive efficacies of about 110 lm W{sup -1} and higher, excellent colour rendering index above 90 and a correlated colour temperature in the 3000-4000 K region at the operating point near the Planckian locus. Moreover, these lamps are opening up the possibility of dimming. Due to the fact that they are able to omit mercury they are environmentally friendly. The emission spectra generated by these HID lamps differ significantly from those of conventional lamps. The reason for this is the dominance of molecular radiation processes. In comparison with conventional HID lamps atomic contributions are usually rather small. In the present case they amount to less than about 10% of the total intensity in the visible range.

Preventing maritime transport of pathogens: the remarkable antimicrobial properties of silver-supported catalysts for ship ballast water disinfection.

Science.gov (United States)

Theologides, C P; Theofilou, S P; Anayiotos, A; Costa, C N

2017-07-01

Ship ballast water (SBW) antimicrobial treatment is considered as a priority issue for the shipping industry. The present work investigates the possibility of utilizing antimicrobial catalysis as an effective method for the treatment of SBW. Taking into account the well-known antimicrobial properties of ionic silver (Ag + ), five silver-supported catalysts (Ag/γ-Al 2 O 3 ) with various loadings (0.05, 0.1, 0.2, 0.5, and 1 wt%) were prepared and examined for the antimicrobial treatment of SBW. The bactericidal activity of the aforementioned catalysts was investigated towards the inhibition of Escherichia coli (Gram-negative) and Escherichia faecalis (Gram-positive) bacteria. Catalytic experiments were conducted in a three-phase continuous flow stirred tank reactor, used in a semi-batch mode. It was found that using the catalyst with the lowest metal loading, the inhibition of E. coli reached 95.8% after 30 minutes of treatment of an E. coli bacterial solution, while the inhibition obtained for E. faecalis was 76.2% after 60 minutes of treatment of an E. faecalis bacterial solution. Even better results (100% inhibition after 5 min of reaction) were obtained using the catalysts with higher Ag loadings. The results of the present work indicate that the prepared monometallic catalysts exert their antimicrobial activity within a short period of time, revealing, for the first time ever, that the field of antimicrobial heterogeneous catalysis using deposited ionic silver on a solid support may prove decisive for the disinfection of SBW.

76 FR 76716 - Draft National Pollutant Discharge Elimination System (NPDES) General Permits for Discharges...

Science.gov (United States)

2011-12-08

...-0141 for the VGP or Docket ID No. EPA-HQ-OW-2011-0150 for the sVGP, by one of the following methods... electronically is EPA's preferred method for receiving comments. Go directly to www.regulations.gov and follow... numeric technology-based effluent limitations that are applicable to vessels with ballast water tanks and...

Quality and economic feasibility of T5 lamp adapters; Qualitaet und Wirtschaftlichkeit von T5-Lampenadaptern - Schlussbericht

Energy Technology Data Exchange (ETDEWEB)

Blattner, P.; Lehmann, H.; Dudli, H.

2008-02-15

This illustrated final report for the Swiss Federal Office of Energy (SFOE) deals with lamp adapters that can be used to modify existing lighting systems in order to allow the use of lamps with lower electrical consumption. In addition, the conventional ballast of such light fittings is replaced with an electronic ballast. This report summarises the results of a study on the quality of lamp adapters, mainly with respect to their photometrical parameters. The measurement equipment used and numerical simulations made are described and discussed. Based on the results of measurements made, various conclusions are drawn on the luminous flux and efficiency of the lamps and the influence of reflectors. Recommendations are made and the performance of two lamp adapter products is commented on. Recommendations for the manufacturers of such adapters are made.

Upfront haploidentical transplant for acquired severe aplastic anemia: registry-based comparison with matched related transplant.

Science.gov (United States)

Xu, Lan-Ping; Jin, Song; Wang, Shun-Qing; Xia, Ling-Hui; Bai, Hai; Gao, Su-Jun; Liu, Qi-Fa; Wang, Jian-Min; Wang, Xin; Jiang, Ming; Zhang, Xi; Wu, De-Pei; Huang, Xiao-Jun

2017-01-21

Haploidentical donor (HID) hematopoietic stem cell transplantation (HSCT) is an alternative treatment method for severe aplastic anemia (SAA) patients lacking suitable identical donors and those who are refractory to immunosuppressive therapy (IST). The current study evaluated the feasibility of upfront haploidentical HSCT in SAA patients. We conducted a multicenter study based on a registry database. One hundred fifty-eight SAA patients who underwent upfront transplantation between June 2012 and September 2015 were enrolled. Eighty-nine patients had haploidentical donors (HIDs), and 69 had matched related donors (MRDs) for HSCT. The median times for myeloid engraftment in the HID and MRD cohorts were 12 (range, 9-20) and 11 (range, 8-19) days, with a cumulative incidence of 97.8 and 97.1% (P = 0.528), respectively. HID recipients had an increased cumulative incidence of grades II-IV acute graft-versus-host disease (aGVHD) (30.3 vs. 1.5%, P < 0.001), grades III-IV aGVHD (10.1 vs. 1.5%, P = 0.026), and chronic GVHD (cGVHD) (30.6 vs. 4.4%, P < 0.001) at 1 year but similar extensive cGVHD (3.4 vs. 0%, P = 0.426). The three-year estimated overall survival (OS) rates were 86.1 and 91.3% (P = 0.358), while the three-year estimated failure-free survival (FFS) rates were 85.0 and 89.8% (P = 0.413) in the HID and MRD cohorts, respectively. In multivariate analysis, survival outcome for the entire population was significantly adversely associated with increased transfusions and poor performance status pre-SCT. We did not observe differences in primary engraftment and survival outcomes by donor type. Haploidentical SCT as upfront therapy was an effective and safe option for SAA patients, with favorable outcomes in experienced centers.

Understanding anode and cathode behaviour in high-pressure discharge lamps

Science.gov (United States)

Flesch, P.; Neiger, M.

2005-09-01

High-intensity discharge (HID) lamps have widespread and modern areas of application including general lighting, video/movie projection (e.g. UHP lamp), street/industrial lighting, and automotive headlight lamps (D2/xenon lamp). Even though HID lamps have been known for several decades now, the important plasma-electrode interactions are still not well understood. Because HID lamps are usually operated on ac (electrodes switch alternately from anode to cathode phase), time-dependent simulations including realistic and verified anode and cathode models are essential. Therefore, a recently published investigation of external laser heating of an electrode during anode and cathode phase in an operating HID lamp [28] provided the basis for our present paper. These measurements revealed impressive influences of the external laser heating on electrode fall voltage and electrode temperature. Fortunately, the effects are very different during anode and cathode phase. Thus, by comparing the experimental findings with results from our numerical simulations we can learn much about the principles of electrode behaviour and explain in detail the differences between anode and cathode phase. Furthermore, we can verify our model (which includes plasma column, hot plasma spots in front of the electrodes, constriction zones and near-electrode non-local thermal equilibrium-plasma as well as anode and cathode) that accounts for all relevant physical processes concerning plasma, electrodes and interactions between them. Moreover, we investigate the influence of two different notions concerning ionization and recombination in the near electrode plasma on the numerical results. This improves our physical understanding of near-electrode plasma likewise and further increases the confidence in the model under consideration. These results are important for the understanding and the further development of HID lamps which, due to their small dimensions, are often experimentally inaccessible

COMMON PATTERNS IN THE EVOLUTION BETWEEN THE LUMINOUS NEUTRON STAR LOW-MASS X-RAY BINARY SUBCLASSES

International Nuclear Information System (INIS)

Fridriksson, Joel K.; Homan, Jeroen; Remillard, Ronald A.

2015-01-01

The X-ray transient XTE J1701–462 was the first source observed to evolve through all known subclasses of low-magnetic-field neutron star low-mass X-ray binaries (NS-LMXBs), as a result of large changes in its mass accretion rate. To investigate to what extent similar evolution is seen in other NS-LMXBs we have performed a detailed study of the color–color and hardness–intensity diagrams (CDs and HIDs) of Cyg X-2, Cir X-1, and GX 13+1—three luminous X-ray binaries, containing weakly magnetized neutron stars, known to exhibit strong secular changes in their CD/HID tracks. Using the full set of Rossi X-ray Timing Explorer Proportional Counter Array data collected for the sources over the 16 year duration of the mission, we show that Cyg X-2 and Cir X-1 display CD/HID evolution with close similarities to XTE J1701–462. Although GX 13+1 shows behavior that is in some ways unique, it also exhibits similarities to XTE J1701–462, and we conclude that its overall CD/HID properties strongly indicate that it should be classified as a Z source, rather than as an atoll source. We conjecture that the secular evolution of Cyg X-2, Cir X-1, and GX 13+1—illustrated by sequences of CD/HID tracks we construct—arises from changes in the mass accretion rate. Our results strengthen previous suggestions that within single sources Cyg-like Z source behavior takes place at higher luminosities and mass accretion rates than Sco-like Z behavior, and lend support to the notion that the mass accretion rate is the primary physical parameter distinguishing the various NS-LMXB subclasses

COMMON PATTERNS IN THE EVOLUTION BETWEEN THE LUMINOUS NEUTRON STAR LOW-MASS X-RAY BINARY SUBCLASSES

Energy Technology Data Exchange (ETDEWEB)

Fridriksson, Joel K. [Anton Pannekoek Institute for Astronomy, University of Amsterdam, Science Park 904, 1098 XH Amsterdam (Netherlands); Homan, Jeroen; Remillard, Ronald A., E-mail: J.K.Fridriksson@uva.nl [Kavli Institute for Astrophysics and Space Research, Massachusetts Institute of Technology, 77 Massachusetts Avenue, Cambridge, MA 02139 (United States)

2015-08-10

The X-ray transient XTE J1701–462 was the first source observed to evolve through all known subclasses of low-magnetic-field neutron star low-mass X-ray binaries (NS-LMXBs), as a result of large changes in its mass accretion rate. To investigate to what extent similar evolution is seen in other NS-LMXBs we have performed a detailed study of the color–color and hardness–intensity diagrams (CDs and HIDs) of Cyg X-2, Cir X-1, and GX 13+1—three luminous X-ray binaries, containing weakly magnetized neutron stars, known to exhibit strong secular changes in their CD/HID tracks. Using the full set of Rossi X-ray Timing Explorer Proportional Counter Array data collected for the sources over the 16 year duration of the mission, we show that Cyg X-2 and Cir X-1 display CD/HID evolution with close similarities to XTE J1701–462. Although GX 13+1 shows behavior that is in some ways unique, it also exhibits similarities to XTE J1701–462, and we conclude that its overall CD/HID properties strongly indicate that it should be classified as a Z source, rather than as an atoll source. We conjecture that the secular evolution of Cyg X-2, Cir X-1, and GX 13+1—illustrated by sequences of CD/HID tracks we construct—arises from changes in the mass accretion rate. Our results strengthen previous suggestions that within single sources Cyg-like Z source behavior takes place at higher luminosities and mass accretion rates than Sco-like Z behavior, and lend support to the notion that the mass accretion rate is the primary physical parameter distinguishing the various NS-LMXB subclasses.

Mis-specified cells die by an active gene-directed process, and inhibition of this death results in cell fate transformation in Drosophila

Science.gov (United States)

Werz, Christian; Lee, Tom V.; Lee, Peter L.; Lackey, Melinda; Bolduc, Clare; Stein, David S.; Bergmann, Andreas

2009-01-01

Summary Incorrectly specified or mis-specified cells often undergo cell death or are transformed to adopt a different cell fate during development. The underlying cause for this distinction is largely unknown. In many developmental mutants in Drosophila, large numbers of mis-specified cells die synchronously, providing a convenient model for analysis of this phenomenon. The maternal mutant bicoid is particularly useful model with which to address this issue because its mutant phenotype is a combination of both transformation of tissue (acron to telson) and cell death in the presumptive head and thorax regions. We show that a subset of these mis-specified cells die through an active gene-directed process involving transcriptional upregulation of the cell death inducer hid. Upregulation of hid also occurs in oskar mutants and other segmentation mutants. In hid bicoid double mutants, mis-specified cells in the presumptive head and thorax survive and continue to develop, but they are transformed to adopt a different cell fate. We provide evidence that the terminal torso signaling pathway protects the mis-specified telson tissue in bicoid mutants from hid-induced cell death, whereas mis-specified cells in the head and thorax die, presumably because equivalent survival signals are lacking. These data support a model whereby mis-specification can be tolerated if a survival pathway is provided, resulting in cellular transformation. PMID:16280349

UV spectrophotometry for monitoring the performance of a yeast-based deoxygenation process to treat ships' ballast water.

Science.gov (United States)

Veilleux, Éloïse; de Lafontaine, Yves; Thomas, Olivier

2016-04-01

This study assessed the usefulness of UV spectrophotometry for the monitoring of a yeast-based deoxygenation process proposed for ships' ballast water treatment to prevent the transfer of aquatic invasive species. Ten-day laboratory experiments using three treatment concentrations and different water types were conducted and resulted in complete oxygen depletion of treated waters. The treatment performance and quality of treated waters were determined by measuring the UV-visible absorbance spectra of water samples taken over time. Samples were also used for laboratory analysis of water quality properties. The UV absorbance spectra values were strongly correlated (r = 0.96) to yeast cell density in treated waters. The second-order derivative (D (2)) of the spectra varied greatly over time, and the spectrum profiles could be divided into two groups corresponding to the oxygenated and anoxic phases of the treatment. The D (2) value at 215 nm was strongly correlated (r = 0.94) to ammonia levels, which increased over time. The D (2) value at 225 nm was strongly correlated (r > 0.97) to DO concentration. Our results showed that UV spectrophotometry may provide a rapid assessment of the behavior and performance of the yeast bioreactor over time by quantifying (1) the density of yeast cells, (2) the time at which anoxic conditions were reached, and (3) a water quality index of the treated water related to the production of ammonia. We conclude that the rapidity of the technique confers a solid advantage over standard methods used for water quality analysis in laboratory and would permit the direct monitoring of the treatment performance on-board ships.

Perancangan Serial Ttl to Usb Hid Converter

OpenAIRE

Gunardi, Yudhi; Munandar, Aris

2015-01-01

Seiring berjalannya waktu, perkembangan teknologi komputer sangat cepat, sehingga memunculkan berbagai software baru dan bermacam operating system. Sementara aktivitas manusia dalam sehari – hari tidak pernah lepas dari komputer sebagai penunjang kerja dengan operating system yang berbeda - beda. Perangkat elektronik untuk komunikasi data yang menunjang kerja manusia mayoritas tidak dapat bekerja secara langsung pada semua operating system.Untuk itu diperlukan sebuah inovasi agar semua perang...

Fluorescent and high intensity discharge lamp use in chambers and greenhouses

Science.gov (United States)

Langhans, Robert W.

1994-01-01

Fluorescent and High Intensity Discharge lamps have opened up great opportunities for researchers to study plant growth under controlled environment conditions and for commercial growers to increase plant production during low/light periods. Specific technical qualities of fluorescent and HID lamps have been critically reviewed. I will direct my remarks to fluorescent and high intensity discharge (HID) lamps in growth chambers, growth rooms, and greenhouses. I will discuss the advantages and disadvantages of using each lamp in growth chambers, growth rooms and greenhouses.

Lighting system with a device for reducing system wattage

NARCIS (Netherlands)

1996-01-01

A lighting system having a high pressure gas discharge lamp intended to be operated on a stabilization ballast further includes a low loss device to reduce the current through the ballast and lamp, thereby reducing system wattage for energy savings. For a lead-type ballast, the current reducing

Comparing the sensitivity of four bioassays for acrolein

NARCIS (Netherlands)

Sneekes, A.C.; Kaag, N.H.B.M.

2009-01-01

Introduction of non-indigenous species is a risk associated with discharge of ballast water from ships transporting cargo between regions. The IMO has set out a mandatory framework for ballast water management on board ships. EnvioMar GmbH has developed a Ballast Water Treatment System (BWTS) using

食用タール色素に関する研究(IX) : 金属イオンによる色素の変色・退色に対するキレート剤の効果(1)

OpenAIRE

神藤, 光野; 打田, 良樹; シントウ, ミツノ; ウチダ, ヨシキ; Mitsuno, SHINTO; Yoshiki, UCHIDA

2007-01-01

本報では、銅、鉄、すず、アルミニウムイオンによる食用タール色素の変色・退色に対するEDTA2Na、EDDS4Na、ASDA4Na、DTPA5Na、HIDS4Naの添加効果を検討した。 銅イオン添加系では、アゾ系色素ではEDTA2Na、EDDS4Na、HIDS4Naがどの色にも添加効果があった。キサンテン系色素では、ASDA4Na、DTPA5Na、HIDS4Naが添加効果がみられた。インジゴイド系色素では全ての添加物で効果が観察された。鉄イオン添加で影響のみられたキサンテン系色素においては、ASDA4Na、DTPA5Na、HIDS4Naを添加することで吸光度が上昇し、HIDS4Naにおいては本来の色調に回復するという傾向を示した。インジゴイド系色素においては、濃度に違いはあるが全ての添加物で吸光度が上昇した。しかし、ASDA4Na、DTPA5Naではキサンテン系色素と同様に沈殿や変色がみられることがわかった。すずイオン添加で影響の見られたアゾ系色素では、全てのキレート剤の全濃度で添加効果が認められた。トリフェニルメタン系色素では、ASDA4Na、DTPA5Na、HIDS4Naの10...

49 CFR Appendix B to Part 564 - Information To Be Submitted for Long Life Replaceable Light Sources of Limited Definition

Science.gov (United States)

2010-10-01

...—Information To Be Submitted for Long Life Replaceable Light Sources of Limited Definition I. Filament or... Source that Operates With a Ballast and Rated Life of the Light Source/Ballast Combination. A. Maximum power (in watts). B. Luminous Flux (in lumens). C. Rated laboratory life of the light source/ballast...

Sole-Source Lighting for Controlled-Environment Agriculture

Science.gov (United States)

Mitchell.Cary; Stutte, Gary W.

2015-01-01

Since plants on Earth evolved under broad-spectrum solar radiation, anytime they are grown exclusively under electric lighting that does not contain all wavelengths in similar proportion to those in sunlight, plant appearance and size could be uniquely different. Nevertheless, plants have been grown for decades under fluorescent (FL) (1) + incandescent (IN) (2) lamps as a sole source of lighting (SSL), and researchers have become comfortable that, in certain proportions of FL + IN for a given species, plants can appear "normal" relative to their growth outdoors. The problem with using such traditional SSLs for commercial production typically is short lamp lifespans and not obtaining enough photosynthetically active radiation (PAR, 400-700 nm) when desired. These limitations led to supplementation of FL + IN lamp outputs with longer-lived, high-intensity discharge (HID) lamps in growth chambers (3). As researchers became comfortable that mixes of orange-biased high-pressure sodium (HPS) and blue-biased metal halide (MH) HIDs together also could give normal plant growth at higher intensities, growth chambers and phytotrons subsequently were equipped mainly with HID lamps, with their intense thermal output filtered out by ventilated light caps or thermal-controlled water barriers. For the most part, IN and HID lamps have found a home in commercial protected horticulture, usually for night-break photoperiod lighting (IN) or for seasonal supplemental lighting (mostly HPS) in greenhouses. However, lack of economically viable options for SSL have held back aspects of year-round indoor agriculture from taking off commercially.

Use of rubber shreds to enhance attenuation of railway sub-ballast layers made of unbound aggregates; Uso de partículas de caucho para mejorar la capacidad de atenuación de capas granulares de subbalasto en ferrocarriles

Energy Technology Data Exchange (ETDEWEB)

Hidalgo-Signes, C.; Garzón-Roca, J.; Grima-Palop, J.M.; Insa-Franco, R.

2017-07-01

One of the approaches for solving the problem of induced vibrations in railways is by slightly modifying the materials that form the track. A study is presented of the attenuation capacity of mixes composed of granular soil and rubber shreds when used as sub-ballast (the layer located immediately below the ballast layer). Rubber shreds are obtained from scrap tyres, a troublesome waste material whose reuse and recycling is necessary. A series of mixes of granular soil and rubber shreds with rubber contents of between 1% and 10% are submitted to hammer impact tests to study their response to dynamic excitation. Results reveal that mixing rubber shreds with granular soil increases damping ratios, thus demonstrating the potential of the proposed mixes for attenuating vibration. [Spanish] Una de las posibles formas de resolver el problema de las vibraciones inducidas por el ferrocarril es llevando a cabo una ligera modificación de los materiales que forman la vía. En este artículo, se presenta un estudio de la capacidad de atenuación de mezclas compuestas por zahorras y partículas de caucho para ser usadas como sub-balasto (capa localizada bajo el balasto). Las partículas de caucho se obtienen a partir de neumáticos fuera de uso, un material problemático cuya reutilización y reciclaje es cada vez más necesario. Las mezclas de zahorra-caucho, con un contenido entre el 1% y 10%, se someten a una serie de ensayos dinámicos mediante impacto con martillo, estudiando su respuesta frente a la excitación dinámica. Los resultados revelan que la mezcla de partículas de caucho con zahorras aumenta el coeficiente de amortiguamiento, lo que muestra el potencial que poseen las mezclas propuestas para la atenuación de vibraciones.

Synthesis of ZnWO{sub 4} Electrode with tailored facets: Deactivating the Microorganisms through Photoelectrocatalytic methods

Energy Technology Data Exchange (ETDEWEB)

Zhan, Su [Department of Materials Science and Engineering, Dalian Maritime University, Dalian 116026 (China); Zhou, Feng, E-mail: zhoufeng99@mails.tsinghua.edu.cn [Department of Materials Science and Engineering, Dalian Maritime University, Dalian 116026 (China); Huang, Naibao; Liu, Yujun; He, Qiuchen; Tian, Yu; Yang, Yifan [Department of Materials Science and Engineering, Dalian Maritime University, Dalian 116026 (China); Ye, Fei [Department of Materials Science and Engineering, Dalian University of Technology, Dalian 116026 (China)

2017-01-01

Highlights: • ZnWO{sub 4} with different exposed facets was synthesized by the hydrothermal method. • The reactive facets were tailored by varying the solution pH. • The photoelectrocatalysis was more efficient in deactivating the microorganism. - Abstract: The exotic invasive species from the ballast water in the ship will bring about serious damages to ecosystem. Photocatalyst films have been widely studied for sterilization. In this study, ZnWO{sub 4} with different exposed facets was synthesized by hydrothermal method, and ZnWO{sub 4} film electrodes have been applied in ballast water treatment through the electro-assisted photocatalytic system. Then the samples were investigated by X-ray diffraction (XRD), X-ray photo-electron spectroscopy (XPS), Field emission on scanning electron microcopy (FE-SEM), Transmission electron microscopy (TEM), UV–vis diffuse reflectance spectroscopy (DRS), BET specific surface area analysis, Fourier transform infrared (FT-IR) and Electrochemical impedance spectra (EIS). ZnWO{sub 4} with an appropriate exposure of (0 1 1) facets ratio exhibited the best photocatalytic and photoelectrocatalytic activities. The microorganisms deactivated completely in 10 min by ZnWO{sub 4} films with 3 V bias. The mechanisms of (0 1 1) facets enhanced the photocatalytic and photoelectrocatalytic activities which were deduced based on the calculated result from the first principles. Simultaneously, appropriate exposed facets and applied bias could reduce the recombination of the photogenerated electron-hole pairs, and improve the photocatalytic activities of ZnWO{sub 4}.

Isolation rooms for highly infectious diseases: an inventory of capabilities in European countries

DEFF Research Database (Denmark)

Fusco, F M; Puro, V; Baka, A

2009-01-01

Isolation of patients with highly infectious diseases (HIDs) in hospital rooms with adequate technical facilities is essential to reduce the risk of spreading disease. The European Network for Infectious Diseases (EUNID), a project co-funded by European Commission and involving 16 European Union...... on prevailing circumstances. Sporadic HID cases can be managed in the available HIRs. HIRs could also have a role in the initial phases of an influenza pandemic. However, large outbreaks due to natural or to bioterrorist events will need management strategies involving healthcare facilities other than HIRs....

Ecological roulette: the global transport of nonindigenous marine organisms.

Science.gov (United States)

Cariton, J T; Geller, J B

1993-07-02

Ocean-going ships carry, as ballast, seawater that is taken on in port and released at subsequent ports of call. Plankton samples from Japanese ballast water released in Oregon contained 367 taxa. Most taxa with a planktonic phase in their life cycle were found in ballast water, as were all major marine habitat and trophic groups. Transport of entire coastal planktonic assemblages across oceanic barriers to similar habitats renders bays, estuaries, and inland waters among the most threatened ecosystems in the world. Presence of taxonomically difficult or inconspicuous taxa in these samples suggests that ballast water invasions are already pervasive.

Tunable light source for fiber optic lighting applications

Science.gov (United States)

Narendran, Nadarajah; Bierman, Andrew; Finney, Mark J.; Edwards, Ian K.

1997-09-01

This paper examines the possibility of tuning the lamp spectrum to compensate for color distortions in fiber optic lighting systems. Because most optical fibers have strong absorption in the blue and red wavelength regions, white light entering and propagating down an optical fiber suffers varied amounts of attenuation as a function of wavelength. As a result, the light exiting the optical fiber has a greenish tint that the lighting design community considers undesirable in interior lighting applications. HID lamps are commonly used for the light source in this industry. Certain classes of HID lamps tend to shift in color when their operating position or the input voltage to the lamp is changed. An experimental study is being conducted to characterize the color shift properties of a small HID lamp as a function of tilt and input voltage. The study also examines the possibility of exploiting this color shift to compensate for the color distortions caused by optical fibers. The details of the experiment and the results are presented in this manuscript.

The breakdown and glow phases during the initiation of discharges for lamps

International Nuclear Information System (INIS)

Pitchford, L.C.; Peres, I.; Liland, K.B.; Boeuf, J.P.; Gielen, H.

1997-01-01

High intensity discharge (HID) lamps are often initiated by the application of one or more short, high-voltage, breakdown pulses superimposed on a 50 or 60 Hz generator voltage. A successful transition from the breakdown event to steady-state operating conditions in HID lamps requires that the lamp-circuit system be adequate to sustain the plasma created during breakdown until the electrodes are heated to thermionic temperatures. In this article, we use a one-dimensional (in the axial direction) transient discharge model to study the conditions needed to sustain the cold-cathode discharge after a breakdown event has occurred. While the application of our one-dimensional model to real lamps is approximate, we find that the model predictions are consistent with experimental results in HID lamps, a few of which are presented here. The main conclusion from this work is that, after breakdown, the voltage necessary to sustain a glow discharge is dependent on the source impedance, the gas composition, and on the plasma density created by the breakdown event. copyright 1997 American Institute of Physics

Surgical treatment of aspergilloma grafted in hydatid cyst cavity

Directory of Open Access Journals (Sweden)

M. El Hammoumi

2013-11-01

Full Text Available Aspergilloma is a saprophytic infection that colonizes pre-existing cavities in the lung. These cavities are caused by tuberculosis, bronchiectasis, lung cancer and other pulmonary diseases. Development of aspergilloma in the residual cavities after pulmonary hydatid cyst surgery is rarely described in terms of coexistence of the two conditions. We describe 3 cases of pulmonary aspergilloma grafted in a residual cavity of cystectomy for hydatid disease. Resumo: Aspergiloma é uma infecção saprófita que coloniza cavidades pré-existentes no pulmão. Estas cavidades são causadas por tuberculose, bronquiectasias, cancro do pulmão e outras doenças pulmonares. O desenvolvimento de aspergiloma em cavidades residuais, após cirurgia pulmonar de quisto hidático, raramente é descrito em termos de coexistência das duas condições. Descrevemos 3 casos de enxerto de aspergiloma pulmonar numa cavidade residual de cistectomia para doença hidática. Keywords: Hydatid cyst, Aspergilloma, Surgery, Capitonnage, Palavras-chave: Quisto hidático, Aspergiloma, Cirurgia, Capitonagem

THE XVI. CENTURY POET SHERÎFÎ’S WORK CALLED SHEVÂHİDÜ’SH-SHÜHEDÂ / XVI. ASIR SAİRLERİNDEN EĞİRDİRLİ SERÎFÎ’NİN SEVÂHİDÜ’S-SÜHEDÂ’SI

Directory of Open Access Journals (Sweden)

Dr. Sadık YAZAR

2009-04-01

Full Text Available In this article, which XVI. century poet Sherîfî’swork called Shevâhidü’sh-shühedâ, that can be a newexample of the maktel (elegy genre, was presented; firstlyI gave brief information about Serîfî and his works. I alsolooked at the maktel (elegy genre’s development and itsexamples in the classical Turkish literature –formbegining to end of the XVI. century- briefly. In the last part of the artcile I compared Sherîfî’s Shevâhidü’shshühedâwith the Fuzûlî’s –the famous XVI. centuryTurkish poet- Hadîqatü’s-sü’edâ and after this compare itwas understood that Sherîfî has benefited from Fuzûlî’swork at the degree of plagiarism. After all these, it wasunderstood that Sherîfî’s Shevâhidü’sh-shühedâ has nomuch value of the originalty.

Managing the environmental impacts of utility lighting retrofits programs

International Nuclear Information System (INIS)

Cress, K.

1993-01-01

One of the most popular demand-side management (DSM) programs currently being sponsored by electric utilities is the removal of old fluorescent light ballasts and replacing them with more efficient models. This type of program, however, can produce a substantial waste stream of the old ballasts, many of which contain Polychlorinated Biphenyl(s) (PCBs), a regulated hazardous substance. The proper disposal of spent light ballasts should be an integral component of DSM programs. This paper will discuss the experience that New England Electric System (NEES) 1 has had with disposing of spent light ballasts resulting from the implementation of our Small Commercial ampersand Industrial Program (a direct install lighting program which provides for the installation of energy efficient lighting measures which include fluorescent fixtures, ballasts and lamps, specular reflectors, compact fluorescent systems, high intensity discharge fixtures, and occupancy sensors. This innovative program is one of the largest in the country and has achieved over 6,000 installations). In this paper, we will review why PCBs are classified as hazardous substances and what effect State and Federal regulations have on the transportation and disposal of ballasts that contain PCBs. Second, we will explain our ballast disposal process which includes collecting, processing, storing, shipping and ultimate disposal. Third, we will discuss our experiences with two different methods of disposal - incineration and recycling. And last we will report on program results

Design of a secondary lens using gaussian function

Science.gov (United States)

Anh, Nguyen Doan Quoc; Long, Nguyen Ngoc; Van Phuoc, Nguyen; Voznak, Miroslav; Zdralek, Jaroslav

2018-04-01

In the article, it is recognized that the high-intensity discharge (HID) fishing lamp becomes obsolete, so we designed a free secondary lens for an LED fishing/working lamp (LFWL) to serve the lighting needs of fishing and the on-board activities on fishing boats through gaussian decomposition for taking the place it. The results proved that it is really useful to the board, sea-surface, and underwater. Moreover, the lighting efficiency of 91 % with the power consumption reducing more than 3 times could be achieved when the proposed LED fishing/working lamps are used instead of the HID fishing lamps.

Buoyancy Limitation of Filamentous Cyanobacteria under Prolonged Pressure due to the Gas Vesicles Collapse.

Science.gov (United States)

Abeynayaka, Helayaye Damitha Lakmali; Asaeda, Takashi; Kaneko, Yasuko

2017-08-01

Freshwater cyanobacterium Pseudanabaena galeata were cultured in chambers under artificially generated pressures, which correspond to the hydrostatic pressures at deep water. Variations occurred in gas vesicles volume, and buoyancy state of cells under those conditions were analyzed at different time intervals (5 min, 1 day, and 5 days). Variations in gas vesicles morphology of cells were observed by transmission electron microscopy images. Settling velocity (Vs) of cells which governs the buoyancy was observed with the aid of a modified optical microscope. Moreover, effects of the prolonged pressure on cell ballast composition (protein and polysaccharides) were examined. Elevated pressure conditions reduced the cell ballast and caused a complete disappearance of gas vesicles in Pseudanabaena galeata cells. Hence cyanobacteria cells were not able to float within the study period. Observations and findings of the study indicate the potential application of hydrostatic pressure, which naturally occurred in hypolimnion of lakes, to inhibit the re-suspension of cyanobacteria cells.

Remotely Operated Vehicle for Surveilance Applications On and Under Water Surface

Directory of Open Access Journals (Sweden)

Mahfuzh Shah Mustari

2017-03-01

Full Text Available This paper presents the low cost hardware prototype of a Remotely Operated Vehicle (ROV for surveilance applications. The vehicle is designed to make maneuvers under water and on surface of water, where its movement is guided remotely via a GHz-scale wireless communication system. The main electronic control unit (ECU of the vehicle is an 8-bit microcontroller, which is used to control 6 motor actuators. Two motors are embedded in a ballast tank used for pumping and draining in and out of the ballast tank. While, the other four motors are used for vehicle movements on water surface. One wireless transceiver is embedded in a joystick and the other is separately placed in the waterproof box mounted on the vehicle. The performance tests present that, in general, the ROV can be controlled well with limited performance. The total weight of the vehicle is 10.35kg with weight density of 0.89kg/ltr

Technical support document: Energy efficiency standards for consumer products: Room air conditioners, water heaters, direct heating equipment, mobile home furnaces, kitchen ranges and ovens, pool heaters, fluorescent lamp ballasts and television sets. Volume 1, Methodology

Energy Technology Data Exchange (ETDEWEB)

1993-11-01

The Energy Policy and Conservation Act (P.L. 94-163), as amended, establishes energy conservation standards for 12 of the 13 types of consumer products specifically covered by the Act. The legislation requires the Department of Energy (DOE) to consider new or amended standards for these and other types of products at specified times. DOE is currently considering amending standards for seven types of products: water heaters, direct heating equipment, mobile home furnaces, pool heaters, room air conditioners, kitchen ranges and ovens (including microwave ovens), and fluorescent light ballasts and is considering establishing standards for television sets. This Technical Support Document presents the methodology, data, and results from the analysis of the energy and economic impacts of the proposed standards. This volume presents a general description of the analytic approach, including the structure of the major models.

New heavy-lift system under construction

Energy Technology Data Exchange (ETDEWEB)

2009-07-01

Heavy-lift availability is at a premium, and the market is eager for alternatives to meet the demand. An alternative heavy-lift solution from SeaMetric - which has two multi-purpose heavy-lift vessels under construction in China - will be available in the first quarter of 2011. The TML system is based on buoyancy and ballast tanks, with four lifting arms mounted on two identical vessels, each vessel measuring 140 x 40 x 10.75 metres. To perform a lift, one TML with lifting arms is positioned on each side of the object. Using seawater pumps, lift force is created by de ballasting the buoyancy tanks and at the same time ballasting the ballast tanks. (AG). tab., ills

An Analysis of Sources of Technological Change in Efficiency Improvement of Fluorescent Lamp Systems

Science.gov (United States)

Imanaka, Takeo

In Japan, energy efficient fluorescent lamp systems which use “rare-earth phosphors” and “electronic ballasts” have shown rapid diffusion since 1990s. This report investigated sources of technological change in the efficiency improvement of fluorescent lamp systems: (i) Fluorescent lamp and luminaires have been under steady technological development for getting more energy efficient lighting and the concepts to achieve high efficiency had been found in such activities; however, it took long time until they realized and become widely used; (ii) Electronic ballasts and rare-earth phosphors add fluorescent lamp systems not only energy efficiency but also various values such as compactness, lightweight, higher output, and better color rendering properties, which have also been expected and have induced research and development (R&D) (iii) Affordable electronic ballasts are realized by the new technology “power MOSFET” which is based on IC technologies and has been developed for large markets of information and communication technologies and mobile devices; and (iv) Rare-earth phosphors became available after rare-earth industries developed for the purpose of supplying rare-earth phosphors for color television. In terms of sources of technological change, (i) corresponds to “R&D” aiming at the particular purpose i.e. energy efficiency in this case, on the other hand, (ii), (iii), and (iv) correspond to “spillovers” from activities aiming at other purposes. This case exhibits an actual example in which “spillovers” were the critical sources of technological change in energy technology.

Resonance broadening of Hg lines as a density diagnostic in high intensity discharge lamps

International Nuclear Information System (INIS)

Lawler, J E

2004-01-01

The use of width measurements on resonance broadened lines of Hg as a density diagnostic in high intensity discharge (HID) lamps is reviewed and further developed in this paper. Optical depths of Hg I lines at 491.6 nm, 577.0 nm, and 1014 nm are computed as a function of temperature to confirm that these lines are optically thin in most HID lamps. The effect of quadratic and quartic radial temperature variation on the width of resonance broadened lines is computed for arc core temperatures from 4000 K to 7000 K. Such variations in temperature, and inverse variations in Hg density, are found to increase the line widths by less than 10% for 'side-on' emission measurements averaged over the arc radius. Theoretical profiles of resonance broadened spectral lines, both radially averaged and as a function of chord offset, are presented. Observations of resonance broadened lines in a metal-halide HID lamp are presented and analysed. It is concluded that the widths of resonance broadened lines provide a convenient and reliable diagnostic for the arc core Hg density but are generally not very sensitive to the radial temperature and Hg density gradient

MATLAB-implemented estimation procedure for model-based assessment of hepatic insulin degradation from standard intravenous glucose tolerance test data.

Science.gov (United States)

Di Nardo, Francesco; Mengoni, Michele; Morettini, Micaela

2013-05-01

Present study provides a novel MATLAB-based parameter estimation procedure for individual assessment of hepatic insulin degradation (HID) process from standard frequently-sampled intravenous glucose tolerance test (FSIGTT) data. Direct access to the source code, offered by MATLAB, enabled us to design an optimization procedure based on the alternating use of Gauss-Newton's and Levenberg-Marquardt's algorithms, which assures the full convergence of the process and the containment of computational time. Reliability was tested by direct comparison with the application, in eighteen non-diabetic subjects, of well-known kinetic analysis software package SAAM II, and by application on different data. Agreement between MATLAB and SAAM II was warranted by intraclass correlation coefficients ≥0.73; no significant differences between corresponding mean parameter estimates and prediction of HID rate; and consistent residual analysis. Moreover, MATLAB optimization procedure resulted in a significant 51% reduction of CV% for the worst-estimated parameter by SAAM II and in maintaining all model-parameter CV% MATLAB-based procedure was suggested as a suitable tool for the individual assessment of HID process. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

Infrared losses from a Na/Sc metal-halide high intensity discharge arc lamp

International Nuclear Information System (INIS)

Smith, D J; Bonvallet, G A; Lawler, J E

2003-01-01

A study of the near-infrared (IR) emission from the arc of a metal-halide high intensity discharge (MH-HID) lamp with a sodium/scandium chemistry is reported. Radiometrically calibrated spectra from 0.7 to 2.5 μm were recorded as a function of position on the arc tube of a 250 W lamp. These spectra were analysed to determine the relative densities of Na and Sc atoms and the arc temperature as a function of radius. Information from these spectra, combined with absorption measurements in the companion paper (Bonvallet and Lawler 2003), were used to determine the absolute output power in the near-IR from the MH-HID lamp

Simultaneous genomic identification and profiling of a single cell using semiconductor-based next generation sequencing

Directory of Open Access Journals (Sweden)

Manabu Watanabe

2014-09-01

Full Text Available Combining single-cell methods and next-generation sequencing should provide a powerful means to understand single-cell biology and obviate the effects of sample heterogeneity. Here we report a single-cell identification method and seamless cancer gene profiling using semiconductor-based massively parallel sequencing. A549 cells (adenocarcinomic human alveolar basal epithelial cell line were used as a model. Single-cell capture was performed using laser capture microdissection (LCM with an Arcturus® XT system, and a captured single cell and a bulk population of A549 cells (≈106 cells were subjected to whole genome amplification (WGA. For cell identification, a multiplex PCR method (AmpliSeq™ SNP HID panel was used to enrich 136 highly discriminatory SNPs with a genotype concordance probability of 1031–35. For cancer gene profiling, we used mutation profiling that was performed in parallel using a hotspot panel for 50 cancer-related genes. Sequencing was performed using a semiconductor-based bench top sequencer. The distribution of sequence reads for both HID and Cancer panel amplicons was consistent across these samples. For the bulk population of cells, the percentages of sequence covered at coverage of more than 100× were 99.04% for the HID panel and 98.83% for the Cancer panel, while for the single cell percentages of sequence covered at coverage of more than 100× were 55.93% for the HID panel and 65.96% for the Cancer panel. Partial amplification failure or randomly distributed non-amplified regions across samples from single cells during the WGA procedures or random allele drop out probably caused these differences. However, comparative analyses showed that this method successfully discriminated a single A549 cancer cell from a bulk population of A549 cells. Thus, our approach provides a powerful means to overcome tumor sample heterogeneity when searching for somatic mutations.

Identification of Colored Dyes that are Resistant to Fading on Exposure to Ethylene Oxide; Use with Indicating FTA™ Sample Collection Cards

Directory of Open Access Journals (Sweden)

Nina Moran

2016-01-01

Full Text Available Regulatory Standards and Forensic Communities are expressing an expectation for HID products to be certified as “DNA-free.” Recently, “DNA-free” status was described for HID-related products using ethylene oxide (EtO; this gas reduces the presence of amplifiable DNA and causes minimal interference to downstream HID-analytical methods. During sample collection, indicating cards, for example, Indicating FTA™ (GE Healthcare Life Sciences, UK, are used to collect and store buccal cell DNA. These cards contain a dye which changes color on application of a colorless sample. Generating “DNA-free” indicating cards using EtO should not impact the dyes' ability to indicate sample location or the efficacy of the card in downstream HID-analytical methods. This study was initiated to identify alternative dyes to those currently used with sample indicating collection cards. The most promising, dyes when applied to cellulose papers exhibited a uniform color distribution and excellent sample indicating properties even when mixed with chemicals associated with FTA™. When dyed cellulose papers were exposed to EtO, ultraviolet radiation, elevated temperature, and humidity, negligible fading or discoloration was observed. The presence of these dyes on cellulose papers did not interfere with direct short tandem repeat (STR profiling. Allelic concordance, first pass success rate, and mean peak heights were comparable to samples applied to Indicating FTA. Biological samples applied to EtO-treated dyed cellulose papers and stored >1 month produced full STR profiles of sufficient quality to allow submission to DNA databases, confirming negligible interference from EtO treatment. These alternative sample indicating dyes resist EtO-mediated fading while fulfilling the Forensic Community's expectation for “DNA-free” with negligible impact on collection card performance.

Hot impact densification: a new method for producing high density ceramic pellets with close shape tolerances

International Nuclear Information System (INIS)

Hrovat, M.; Huschka, H.; Muhling, G.; Rachor, L.; Zimmerman, H.

1982-01-01

Density and correct diameter of nuclear fuel pellets are usually achieved by sintering and subsequent circular grinding. Hot impact densification (HID) thermally squatted ceramic bodies can be directly high speed precision-molded in a cold die. For thermoshock-sensitive materials, a controlled cooling down procedure of some minutes is added. The feasibility of HID has been demonstrated on the laboratory scale on UO 2 , UC, and some more materials at temperatures between 1700 and 2300 0 C, pressures up to 800 N/mm 2 . Shape tolerances are close, density can be exactly reproduced within a wide range. Tool wear seems to be no problem. Currently, a prototype facility for continuous performance is being developed

Abundance of pollution indicator and pathogenic bacteria in Mumbai waters

Digital Repository Service at National Institute of Oceanography (India)

Ramaiah, N.; Kolhe, V.; Sadhasivan, A

As a part of environmental assessment in the Mumbai Harbour region, where large numbers of ships either take in ballast from- or discharge their ballast, many groups of indicator and human pathogenic bacteria were quantified. Samples (water...

The effect of active antennas on the hot-restrike of high intensity discharge lamps

International Nuclear Information System (INIS)

Hoebing, T; Bergner, A; Ruhrmann, C; Mentel, J; Awakowicz, P; Koch, B; Manders, F

2014-01-01

The ignition voltage of high intensity discharge (HID) lamps with mercury as the buffer gas may rise from 3 kV for the cold state up to more than 15 kV for a hot lamp. By coating a lamp burner with an electrically conductive layer, which operates as an active antenna, the ignition voltage of HID lamps can be significantly reduced. An active antenna connected to one of the lamp electrodes transports the potential from this electrode to the vicinity of the opposite electrode and generates an enhanced electric field inside the burner. On applying a symmetrically shaped ignition pulse, a weak pre-discharge within the first half-cycle produces free charge carriers initiating ignition of the lamp within the subsequent second half-cycle. The authors present a set-up for electrical and optical investigations of hot-restrike in HID lamps. The ignition voltage is measured for two different polarities as a function of the cooldown time. An analysis of its reduction is given. Furthermore, the pre-discharge is investigated by means of short-time photography. It is demonstrated that a negative polarity of the active antenna within the first half-cycle and a positive polarity within the second one is the most effective succession. (paper)

On the use of the serial dilution culture method to enumerate viable phytoplankton in natural communities of plankton subjected to ballast water treatment.

Science.gov (United States)

Cullen, John J; MacIntyre, Hugh L

2016-01-01

Discharge standards for ballast water treatment (BWT) systems are based on concentrations of living cells, for example, as determined with vital stains. Ultraviolet radiation (UV) stops the reproduction of microorganisms without killing them outright; they are living, but not viable, and ecologically as good as dead. Consequently, UV-treated discharge can be compliant with the intent of regulation while failing a live/dead test. An alternative evaluation of BWT can be proposed based on the assessment of viable, rather than living, cells in discharge water. In principle, the serial dilution culture-most probable number (SDC-MPN) method provides the appropriate measure for phytoplankton. But, the method has been criticized, particularly because it is thought that many phytoplankton species cannot be cultured. A review of the literature shows that although SDC-MPN has been used for more than 50 years-generally to identify and count phytoplankton species that cannot be preserved-its application to enumerate total viable phytoplankton seems to be new, putting past criticisms of the method in a different light. Importantly, viable cells need to grow only enough to be detected, not to be brought into sustained culture, and competition between species in a dilution tube is irrelevant as long as the winner is detectable. Thorough consideration of sources of error leads to recommendations for minimizing and quantifying uncertainties by optimizing growth conditions and conducting systematic comparisons. We conclude that with careful evaluation, SDC-MPN is potentially an effective method for assessing the viability of phytoplankton after BWT.

Targeted sequencing of clade-specific markers from skin microbiomes for forensic human identification.

Science.gov (United States)

Schmedes, Sarah E; Woerner, August E; Novroski, Nicole M M; Wendt, Frank R; King, Jonathan L; Stephens, Kathryn M; Budowle, Bruce

2018-01-01

The human skin microbiome is comprised of diverse communities of bacterial, eukaryotic, and viral taxa and contributes millions of additional genes to the repertoire of human genes, affecting human metabolism and immune response. Numerous genetic and environmental factors influence the microbiome composition and as such contribute to individual-specific microbial signatures which may be exploited for forensic applications. Previous studies have demonstrated the potential to associate skin microbial profiles collected from touched items to their individual owner, mainly using unsupervised methods from samples collected over short time intervals. Those studies utilize either targeted 16S rRNA or shotgun metagenomic sequencing to characterize skin microbiomes; however, these approaches have limited species and strain resolution and susceptibility to stochastic effects, respectively. Clade-specific markers from the skin microbiome, using supervised learning, can predict individual identity using skin microbiomes from their respective donors with high accuracy. In this study the hidSkinPlex is presented, a novel targeted sequencing method using skin microbiome markers developed for human identification. The hidSkinPlex (comprised of 286 bacterial (and phage) family-, genus-, species-, and subspecies-level markers), initially was evaluated on three bacterial control samples represented in the panel (i.e., Propionibacterium acnes, Propionibacterium granulosum, and Rothia dentocariosa) to assess the performance of the multiplex. The hidSkinPlex was further evaluated for prediction purposes. The hidSkinPlex markers were used to attribute skin microbiomes collected from eight individuals from three body sites (i.e., foot (Fb), hand (Hp) and manubrium (Mb)) to their host donor. Supervised learning, specifically regularized multinomial logistic regression and 1-nearest-neighbor classification were used to classify skin microbiomes to their hosts with up to 92% (Fb), 96% (Mb

Impact of increasing freight loads on rail substructure from fracking sand transportation.

Science.gov (United States)

2014-03-01

In this report the effect of surface infiltration of frac sand and heavy axle loads (HALs) were studied for their impact on the ballast layer. : Different combinations of ballast and fracking sand were constructed to observe long term trends of defor...

Electron beam accelerators—trends in radiation processing technology for industrial and environmental applications in Latin America and the Caribbean

Science.gov (United States)

Parejo Calvo, Wilson A.; Duarte, Celina L.; Machado, Luci Diva B.; Manzoli, Jose E.; Geraldo, Aurea Beatriz C.; Kodama, Yasko; Silva, Leonardo Gondim A.; Pino, Eddy S.; Somessari, Elizabeth S. R.; Silveira, Carlos G.; Rela, Paulo R.

2012-08-01

The radiation processing technology for industrial and environmental applications has been developed and used worldwide. In Latin America and the Caribbean and particularly in Brazil there are 24 and 16 industrial electron beam accelerators (EBA) respectively with energy from 200 keV to 10 MeV, operating in private companies and governmental institutions to enhance the physical and chemical properties of materials. However, there are more than 1500 high-current electron beam accelerators in commercial use throughout the world. The major needs and end-use markets for these electron beam (EB) units are R and D, wire and electric cables, heat shrinkable tubes and films, PE foams, tires, components, semiconductors and multilayer packaging films. Nowadays, the emerging opportunities in Latin America and the Caribbean are paints, adhesives and coatings cure in order to eliminate VOCs and for less energy use than thermal process; disinfestations of seeds; and films and multilayer packaging irradiation. For low-energy EBA (from 150 keV to 300 keV). For mid-energy EBA (from 300 keV to 5 MeV), they are flue gas treatment (SO2 and NOX removal); composite and nanocomposite materials; biodegradable composites based on biorenewable resources; human tissue sterilization; carbon and silicon carbide fibers irradiation; irradiated grafting ion-exchange membranes for fuel cells application; electrocatalysts nanoparticles production; and natural polymers irradiation and biodegradable blends production. For high-energy EBA (from 5 MeV to 10 MeV), they are sterilization of medical, pharmaceutical and biological products; gemstone enhancement; treatment of industrial and domestic effluents and sludge; preservation and disinfestations of foods and agricultural products; soil disinfestations; lignocellulosic material irradiation as a pretreatment to produce ethanol biofuel; decontamination of pesticide packing; solid residues remediation; organic compounds removal from wastewater; and

Electron beam accelerators—trends in radiation processing technology for industrial and environmental applications in Latin America and the Caribbean

International Nuclear Information System (INIS)

Parejo Calvo, Wilson A.; Duarte, Celina L.; Machado, Luci Diva B.; Manzoli, Jose E.; Geraldo, Aurea Beatriz C.; Kodama, Yasko; Silva, Leonardo Gondim A.; Pino, Eddy S.; Somessari, Elizabeth S.R.; Silveira, Carlos G.

2012-01-01

The radiation processing technology for industrial and environmental applications has been developed and used worldwide. In Latin America and the Caribbean and particularly in Brazil there are 24 and 16 industrial electron beam accelerators (EBA) respectively with energy from 200 keV to 10 MeV, operating in private companies and governmental institutions to enhance the physical and chemical properties of materials. However, there are more than 1500 high-current electron beam accelerators in commercial use throughout the world. The major needs and end-use markets for these electron beam (EB) units are R and D, wire and electric cables, heat shrinkable tubes and films, PE foams, tires, components, semiconductors and multilayer packaging films. Nowadays, the emerging opportunities in Latin America and the Caribbean are paints, adhesives and coatings cure in order to eliminate VOCs and for less energy use than thermal process; disinfestations of seeds; and films and multilayer packaging irradiation. For low-energy EBA (from 150 keV to 300 keV). For mid-energy EBA (from 300 keV to 5 MeV), they are flue gas treatment (SO 2 and NO X removal); composite and nanocomposite materials; biodegradable composites based on biorenewable resources; human tissue sterilization; carbon and silicon carbide fibers irradiation; irradiated grafting ion-exchange membranes for fuel cells application; electrocatalysts nanoparticles production; and natural polymers irradiation and biodegradable blends production. For high-energy EBA (from 5 MeV to 10 MeV), they are sterilization of medical, pharmaceutical and biological products; gemstone enhancement; treatment of industrial and domestic effluents and sludge; preservation and disinfestations of foods and agricultural products; soil disinfestations; lignocellulosic material irradiation as a pretreatment to produce ethanol biofuel; decontamination of pesticide packing; solid residues remediation; organic compounds removal from wastewater; and

Control of single-phase islanded PV/battery streetlight cluster based on power-line signaling

DEFF Research Database (Denmark)

Quintana, Pablo; Garcia, Jorge; Guerrero, Josep M.

2013-01-01

. The whole system is explained ahead and finally, simulation results obtained in Simulink are presented to validate the proposed control strategy. On the other hand, the proposed loads are several electromagnetic ballast driving high pressure sodium (HPS) lamps. Although this kind of ballast...

Marine air : shipping emissions in ports and their impact on local air quality. A case study on the ports of Delfzijl and Eemshaven.

NARCIS (Netherlands)

Meer van der, Ruurd

2012-01-01

Summary Ships translocate organisms across the world via on-board ballast water. When a ship releases its ballast water these organism are released as well. They might have the advantage of not having any natural enemies in their new environment and they

Systematic life-cycle analysis and performance of enhanced trackbed support.

Science.gov (United States)

2015-09-21

The first objective of this project is to develop a method to measure the pressure distribution and magnitude as well as contact area at the ballast-tie interface under heavy haul, Class I type loading. Ballast degradation at this interface has been ...

Nummular keratopathy in a patient with Hyper-IgD Syndrome

Directory of Open Access Journals (Sweden)

Culican Susan M

2009-08-01

Full Text Available Abstract Purpose To report a case of recurrent nummular keratitis in a pediatric patient with Hyperimmunoglobulinemia D syndrome. Methods A retrospective chart review. Results A 14-year-old boy with Hyperimmunoglobulinemia D syndrome (HIDS presented with photophobia and ocular irritation concomitant with disease exacerbation. He was found on exam to have significant nummular keratitis, which responded to a short course of topical steroids. Despite acute response to local immunosuppression, the patient had several recurrent attacks and eventually developed a large corneal scar and decreased vision. After initiation of infliximab therapy his ocular sequelae improved dramatically and his vision returned to 20/20. Conclusion One possible form of end-organ damage associated with HIDS is vision threatening nummular keratopathy.

Hybrid Intrusion Detection System for DDoS Attacks

Directory of Open Access Journals (Sweden)

Özge Cepheli

2016-01-01

Full Text Available Distributed denial-of-service (DDoS attacks are one of the major threats and possibly the hardest security problem for today’s Internet. In this paper we propose a hybrid detection system, referred to as hybrid intrusion detection system (H-IDS, for detection of DDoS attacks. Our proposed detection system makes use of both anomaly-based and signature-based detection methods separately but in an integrated fashion and combines the outcomes of both detectors to enhance the overall detection accuracy. We apply two distinct datasets to our proposed system in order to test the detection performance of H-IDS and conclude that the proposed hybrid system gives better results than the systems based on nonhybrid detection.

Analyzing the Energy Performance, Wind Loading, and Costs of Photovoltaic Slat Modules on Commercial Rooftops

Energy Technology Data Exchange (ETDEWEB)

Van Geet, Otto D. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Fu, Ran [National Renewable Energy Lab. (NREL), Golden, CO (United States); Horowitz, Kelsey A. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kurup, Parthiv [National Renewable Energy Lab. (NREL), Golden, CO (United States); MacAlpine, Sara M. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Silverman, Timothy J. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2018-02-13

NREL studied a new type of photovoltaic (PV) module configuration wherein multiple narrow, tilted slats are mounted in a single frame. Each slat of the PV slat module contains a single row of cells and is made using ordinary crystalline silicon PV module materials and processes, including a glass front sheet and weatherproof polymer encapsulation. Compared to a conventional ballasted system, a system using slat modules offer higher energy production and lower weight at lower LCOE. The key benefits of slat modules are reduced wind loading, improved capacity factor and reduced installation cost. First, the individual slats allow air to flow through, which reduce wind loading. Using PV performance modeling software, we compared the performance of an optimized installation of slats modules to a typical installation of conventional modules in a ballasted rack mounting system. Based on the results of the performance modeling two different row tilt and spacing were tested in a wind tunnel. Scaled models of the PV Slat modules were wind tunnel tested to quantify the wind loading of a slat module system on a commercial rooftop, comparing the results to conventional ballasted rack mounted PV modules. Some commercial roofs do not have sufficient reserve dead load capacity to accommodate a ballasted system. A reduced ballast system design could make PV system installation on these roofs feasible for the first time without accepting the disadvantages of penetrating mounts. Finally, technoeconomic analysis was conducted to enable an economic comparison between a conventional commercial rooftop system and a reduced-ballast slat module installation.

10 CFR 431.323 - Materials incorporated by reference.

Science.gov (United States)

2010-01-01

... National Standard for Lamp Ballasts—Ballasts for High-Intensity Discharge Lamps—Methods of Measurement... AND INDUSTRIAL EQUIPMENT Metal Halide Lamp Ballasts and Fixtures Test Procedures § 431.323 Materials... National Standard for electric lamps: Single-Ended Metal Halide Lamps, approved May 5, 2004, IBR approved...

Disease: H00206 [KEGG MEDICUS

Lifescience Database Archive (English)

Full Text Available MVA show the symptoms, including dysmorphic features, cataracts, neurologic symptoms. The majority of patien...ts with HIDS experience only recurrent febrile crises, without any neurologic abnormalities or dysmorphic

One-dimensional diffusion model in an Inhomogeneous region

CSIR Research Space (South Africa)

Fedotov, I

2006-01-01

Full Text Available ) of these atoms. The enthalpy of formation of free atoms, ∆H, can vary between 50 and 300 kJ.mol-1. The ballast is heated by radiation from the walls of the atomizer, and its temperature, Tb(t), is given by the Stefan-Boltzmann equation [4...]: ( )ddt T t E c S V T t T tb b b b b b w b( ) ( ) ( )= −σ ρ 4 4 (6) where σ is the Stefan-Boltzmann constant, Eb is the emissivity of the ballast material, cb is the heat capacity of ballast material, ρb...

Proposal of an intelligent wayside monitoring system for detection of critical ice accumulations on railway vehicles

Science.gov (United States)

Michelberger, Frank; Wagner, Adrian; Ostermann, Michael; Maly, Thomas

2017-09-01

At railway lines with ballasted tracks, under unfavourable conditions, the so-called flying ballast can occur predominantly for trains driving at high speeds. Especially in wintertime, it is highly likely that the causes are adhered snow or ice deposits, which are falling off the vehicle. Due to the high kinetic energy, the impact can lead to the removal of ballast stones from the structure of the ballasted track. If the stones reach the height of vehicles underside, they may be accelerated significantly due to the collision with the vehicle or may detach further ice blocks. In the worst case, a reinforcing effect occurs, which can lead to considerable damage to railway vehicles (under-floor-area, vehicle exteriors, etc.) and infrastructure (signal masts, noise barriers, etc.). Additionally the flying gravel is a significant danger to people in the nearby area of the tracks. With this feasibility study the applicability and meaningfulness of an intelligent monitoring system for identification of the critical ice accumulation to prevent the ballast fly induced by ice dropping was examined. The key findings of the research are that the detection of ice on railway vehicles and the development of an intelligent monitoring seem to be possible with existing technologies, but a proof of concept in terms of field tests is necessary.

Pesky Critters

National Research Council Canada - National Science Library

Kloeppel, Kirk M

2005-01-01

The synergy of quantum physics, nanotechnology, and the new science of biomimicry portend the bedrock of the machinery needed to produce the housefly unmanned vehicle, a sensor device no enemy could hid...

76 FR 65362 - Energy Conservation Program: Compliance Date Regarding the Test Procedures for Walk-In Coolers...

Science.gov (United States)

2011-10-21

... Freezers and the Certification for Metal Halide Lamp Ballasts and Fixtures AGENCY: Office of Energy... the Department of metal halide lamp ballasts and fixtures. DATES: This final rule is effective... starting October 12, 2011; that is, 180 days after publication of the test procedure final rule. DOE...

Experimental study of the effect of high porewater salinity on the physical properties of a natural smectitic clay

Energy Technology Data Exchange (ETDEWEB)

Pusch, Roland [Geodevelopment AB, Lund (Sweden)

2001-03-01

Natural smectitic clays for backfilling tunnels and shafts in deep repositories may be an alternative to mixtures of bentonite and ballast. Very salt groundwater is known to raise the hydraulic conductivity and reduce the expandability of clay materials in general and of bentonite/ballast mixtures in particular and the present study aimed at determining the impact of salt water on the major physical properties of natural smectitic clays, represented by the German Friedland Ton. The investigation showed that the compactability of the investigated clay is not significantly affected by the water content in contrast to bentonite/ballast fills, and that the conductivity and expandability are acceptable even at salt contents of up to 20 % if the bulk density at saturation is slightly higher than 2000 kg/m{sup 3} . For salt contents up to 3. 5 % the corresponding density is around 1900 kg/m{sup 3}. In general, the investigated clay offers better physical properties than mixtures of bentonite/ballast mixtures with up to 30 % bentonite content.

Experimental study of the effect of high porewater salinity on the physical properties of a natural smectitic clay

International Nuclear Information System (INIS)

Pusch, Roland

2001-03-01

Natural smectitic clays for backfilling tunnels and shafts in deep repositories may be an alternative to mixtures of bentonite and ballast. Very salt groundwater is known to raise the hydraulic conductivity and reduce the expandability of clay materials in general and of bentonite/ballast mixtures in particular and the present study aimed at determining the impact of salt water on the major physical properties of natural smectitic clays, represented by the German Friedland Ton. The investigation showed that the compactability of the investigated clay is not significantly affected by the water content in contrast to bentonite/ballast fills, and that the conductivity and expandability are acceptable even at salt contents of up to 20 % if the bulk density at saturation is slightly higher than 2000 kg/m 3 . For salt contents up to 3. 5 % the corresponding density is around 1900 kg/m 3 . In general, the investigated clay offers better physical properties than mixtures of bentonite/ballast mixtures with up to 30 % bentonite content

Quantifying potential propagule pressure of aquatic invasive species from the commercial shipping industry in Canada.

Science.gov (United States)

Lo, Veronica B; Levings, Colin D; Chan, Kai M A

2012-02-01

We quantify and compare different measures of potential propagule pressure (PPP) of aquatic invasive species (AIS) from commercial vessels in Canada. We used ship arrivals and ballast water discharge volumes as proxies for PPP from ballast water organisms, and wetted surface area (WSA) as a proxy for hull fouling PPP, to determine their relative contributions to total PPP. For three regions studied, PPP proxies correlated significantly across ports and some vessel categories. Relative contributions of ship arrivals, ballast discharge, and WSAs to PPP, evidenced by non-significant correlations across these measures, varied across regions, ports, vessel types, and seasons. Flow-through (dominant on east and west coasts) and empty-refill (in Great Lakes-St. Lawrence region) were the major ballast water exchange methods employed by the vessels surveyed. These methods have different biological efficacy for AIS removal, influencing PPP. Our study illustrates benefits and limitations of using different PPP proxies to estimate invasion risk. Copyright © 2011 Elsevier Ltd. All rights reserved.

Quality of Slab Track Construction - Track Alignment Design and Track Geometry

Science.gov (United States)

Šestáková, Janka

2015-05-01

The slab track superstructure design (without ballast) is a perspective construction especially for building tunnels and bridges in the modernized sections of railway tracks in Slovakia. Monitoring of the structure described in this article is focused on the transition areas between standard structure with ballast and slab track construction.

Hybrid Discrete Element - Finite Element Simulation for Railway Bridge-Track Interaction

Science.gov (United States)

Kaewunruen, S.; Mirza, O.

2017-10-01

At the transition zone or sometimes called ‘bridge end’ or ‘bridge approach’, the stiffness difference between plain track and track over bridge often causes aggravated impact loading due to uneven train movement onto the area. The differential track settlement over the transition has been a classical problem in railway networks, especially for the aging rail infrastructures around the world. This problem is also additionally worsened by the fact that the construction practice over the area is difficult, resulting in a poor compaction of formation and subgrade. This paper presents an advanced hybrid simulation using coupled discrete elements and finite elements to investigate dynamic interaction at the transition zone. The goal is to evaluate the dynamic stresses and to better understand the impact dynamics redistribution at the bridge end. An existing bridge ‘Salt Pan Creek Railway Bridge’, located between Revesby and Kingsgrove, has been chosen for detailed investigation. The Salt Pan Bridge currently demonstrates crushing of the ballast causing significant deformation and damage. Thus, it’s imperative to assess the behaviours of the ballast under dynamic loads. This can be achieved by modelling the nonlinear interactions between the steel rail and sleeper, and sleeper to ballast. The continuum solid elements of track components have been modelled using finite element approach, while the granular media (i.e. ballast) have been simulated by discrete element method. The hybrid DE/FE model demonstrates that ballast experiences significant stresses at the contacts between the sleeper and concrete section. These overburden stress exists in the regions below the outer rails, identify fouling and permanent deformation of the ballast.

MOOC Introduction to Dutch

NARCIS (Netherlands)

den Hollander, Franciscus; Piersma, Kristien

Interview met Margriet Hidding, Birgit Lijmbach en Jeroen van Engen, medewerkers van het Talencentrum en de makers van de Massive Open Online Course (MOOC) Introduction to Dutch over het grote succes van deze cursus

78 FR 38800 - Panda Power LLC, Denial of Petition for Decision of Inconsequential Noncompliance

Science.gov (United States)

2013-06-27

... that the subject HID headlamp kits may not comply with one or more of the regulations enforced by the... systemic, pervasive, and substantial, creating a significant safety risk to the motoring public. Michael F...

Quantitative x-ray absorption imaging with a broadband source: application to high-intensity discharge lamps

Energy Technology Data Exchange (ETDEWEB)

Curry, J J [National Institute of Standards and Technology, Gaithersburg, MD 20899-8422 (United States)], E-mail: jjcurry@nist.gov

2008-07-21

The case of x-ray absorption imaging in which the x-ray source is broadband and the detector does not provide spectral resolution is analysed. The specific motivation is observation of the Hg vapour distribution in high-intensity discharge (HID) lamps. When absorption by the vapour is small, the problem can be couched accurately in terms of a mean absorption cross section averaged over the x-ray spectral distribution, weighted by the energy-dependent response of the detector. The method is tested against a Au foil standard and then applied to Hg. The mean absorption cross section for Hg is calculated for a Ag-anode x-ray tube at accelerating voltages of 25, 30 and 35 kV, and for HIDs in fused silica or polycrystalline alumina arc tubes.

A Baseline Analysis of Combat Logistics Force Scheduling Efficiency

Science.gov (United States)

2016-06-01

minimize the total ballast (empty) leg of a voyage and therefore minimized overall costs (1983, p. 123). Ronen suggested, in 1983, that computerized...non-working distance is the distance required to return to port and this is known as the ballast leg of the voyage. In Example 1, the working

Modelling of Non-Linear Pilot Disinfection Water System: A Bond Graph Approach

Directory of Open Access Journals (Sweden)

Naoufel ZITOUNI

2012-08-01

Full Text Available The ultraviolet (UV irradiations are used to solve the bacteriological problem of the drinking water quality. A discharge-gas lamp is used to produce this type of irradiation. The UV lamp is fed by photovoltaic (PV energy via electronic ballast composed by an inverter, a transformer and resonant circuit (RLC. The aim of this work is to give a useful global model of the system. In particular, we introduce the complicated UV lamp model and the water disinfection kinetics, where the radiant energy flux emitted by the discharge-gas lamp and the arc voltage are a complex functions of the current and time. This system is intended to be mainly used in rural zones, the photovoltaic modules as source of energy is an adequate solution. To optimise the power transfer from the PV array to ballast and UV lamp, a Maximum Power Point Tracking (MPPT device may be located between PV array and the loads. In this paper, we developed a bond-graph model which gives the water quality from UV flow, gas type, pressure, lamp current and geometrical characteristic. Finally reliable simulations are established and compared with experimental tests.

Buildings sector demand-side efficiency technology summaries

Energy Technology Data Exchange (ETDEWEB)

Koomey, J.G.; Johnson, F.X.; Schuman, J. [and others

1994-03-01

This report provides descriptions of the following energy efficiency technologies: energy management systems; electronic fluorescent ballasts; compact fluorescent lamps; lighting controls; room air conditioners; high albedo materials, coatings and paints; solar domestic water heaters; heat pump water heaters; energy-efficient motors; adjustable-speed drives; energy-efficient refrigerators; daylight control glazing; insulating glazing; solar control glazing; switchable glazing; tree planting; and advanced insulation. For each technology, the report provides a description of performance characteristics, consumer utility, development status, technology standards, equipment cost, installation, maintenance, conservation programs, and environmental impacts.

Restoration and Preservation of Engraved Limestone Blocks Discovered in Abu Mousa Excavation, Suez - Egypt

Directory of Open Access Journals (Sweden)

Nabil A. Abd El-Tawab BADER

2013-03-01

Full Text Available A lot of engraved limestone blocks were discovered at Awlad Abu Musa (east of Suez, Egypt in 1995/2007 by Supreme Council of Antiquities. The stone blocks were seriously affected by archaeological environments during burial environment in agriculture land. They were covered with thick clay layer with soil particles that disfigured them and hid their inscriptions. Prior to the conservation intervention, the materials were characterized by X-ray diffraction, optical microscopy, scanning electron microscopy with energy-dispersive X-ray spectroscopy, Chemical analyses of ground water and microbiological study. After the material characterization, the conservation and restoration of the stone blocks were carried out including cleaning, consolidation, reduction of salts, Re-jointing, restoration and completion of lost parts. After that the blocks were exhibited in Suez museum.

33 CFR 151.05 - Definitions.

Science.gov (United States)

2010-07-01

..., wire, and steel strapping. Clean ballast means the ballast in a tank which, since oil was last carried... scientific research relating to pollution abatement or control. Dishwater means the liquid residue from the... facilities, and mineral and oil industry shorebases to be terminals for the purposes of Annex V of MARPOL 73...

Quality of Slab Track Construction – Track Alignment Design and Track Geometry

Directory of Open Access Journals (Sweden)

Šestáková Janka

2015-05-01

Full Text Available The slab track superstructure design (without ballast is a perspective construction especially for building tunnels and bridges in the modernized sections of railway tracks in Slovakia. Monitoring of the structure described in this article is focused on the transition areas between standard structure with ballast and slab track construction.

cyril of alexandria speaks for god in his interpretation of the holy bible

African Journals Online (AJOL)

UV/UFS. . Dr. Eirini Artemi, Greek Archdiocese of Athens, ... metaphors and types, led infants to maturity and hid the beauty of the ..... in the authors of the New Testament resembles the lamp in the tent of.

Sinking rates and ballast composition of particles in the Atlantic Ocean: implications for the organic carbon fluxes to the deep ocean

Science.gov (United States)

Fischer, G.; Karakaş, G.

2009-01-01

The flux of materials to the deep sea is dominated by larger, organic-rich particles with sinking rates varying between a few meters and several hundred meters per day. Mineral ballast may regulate the transfer of organic matter and other components by determining the sinking rates, e.g. via particle density. We calculated particle sinking rates from mass flux patterns and alkenone measurements applying the results of sediment trap experiments from the Atlantic Ocean. We have indication for higher particle sinking rates in carbonate-dominated production systems when considering both regional and seasonal data. During a summer coccolithophorid bloom in the Cape Blanc coastal upwelling off Mauritania, particle sinking rates reached almost 570 m per day, most probably due the fast sedimentation of densely packed zooplankton fecal pellets, which transport high amounts of organic carbon associated with coccoliths to the deep ocean despite rather low production. During the recurring winter-spring blooms off NW Africa and in opal-rich production systems of the Southern Ocean, sinking rates of larger particles, most probably diatom aggregates, showed a tendency to lower values. However, there is no straightforward relationship between carbonate content and particle sinking rates. This could be due to the unknown composition of carbonate and/or the influence of particle size and shape on sinking rates. It also remains noticeable that the highest sinking rates occurred in dust-rich ocean regions off NW Africa, but this issue deserves further detailed field and laboratory investigations. We obtained increasing sinking rates with depth. By using a seven-compartment biogeochemical model, it was shown that the deep ocean organic carbon flux at a mesotrophic sediment trap site off Cape Blanc can be captured fairly well using seasonal variable particle sinking rates. Our model provides a total organic carbon flux of 0.29 Tg per year down to 3000 m off the NW African upwelling

Sadhana | Indian Academy of Sciences

Indian Academy of Sciences (India)

Therefore, the proposed ballast maintains unity-power-factor and high efficiency with ripple-free input current over wide range of input line voltage in case of worst regulation. A symmetrical half-bridge inverter is used to drive the fluorescent lamps. The experimental results of the laboratory prototype ballast for 2 × 36 W ...

Electron/electron acoustic instability

International Nuclear Information System (INIS)

Gary, S.P.

1987-01-01

The electron acoustic wave becomes a normal mode of an unmagnetized collisionless plasma in the presence of two electron components with similar densities, but strongly disparate temperatures. The characteristic frequency of this mode is the plasma frequency of the cooler electron component. If these two electron components have a relative drift speed several times the thermal speed of the cooler component, the electron/electron acoustic instability may arise. This paper describes the parametric dependences of the threshold drift speed and maximum growth rate of this instability, and compares these with the same properties of the electron/ion acoustic instability. Under the condition of zero current, the electron/ion acoustic instability typically has the lower threshold drift speed, so that observation of the electron/electron acoustic instability is a strong indication of the presence of an electrical current in the plasma

Electronics and electronic systems

CERN Document Server

Olsen, George H

1987-01-01

Electronics and Electronic Systems explores the significant developments in the field of electronics and electronic devices. This book is organized into three parts encompassing 11 chapters that discuss the fundamental circuit theory and the principles of analog and digital electronics. This book deals first with the passive components of electronic systems, such as resistors, capacitors, and inductors. These topics are followed by a discussion on the analysis of electronic circuits, which involves three ways, namely, the actual circuit, graphical techniques, and rule of thumb. The remaining p

Electrons, Electronic Publishing, and Electronic Display.

Science.gov (United States)

Brownrigg, Edwin B.; Lynch, Clifford A.

1985-01-01

Provides a perspective on electronic publishing by distinguishing between "Newtonian" publishing and "quantum-mechanical" publishing. Highlights include media and publishing, works delivered through electronic media, electronic publishing and the printed word, management of intellectual property, and recent copyright-law issues…

Influence of chelating ligands on arsenic uptake by hydroponically grown rice seedlings (Oryza sativa L.): a preliminary study

Energy Technology Data Exchange (ETDEWEB)

Rahman, Mohammad A.; Hasegawa, Hiroshi; Ueda, Kazumasa; Maki, Teruya [Graduate School of Natural Science and Technology, Kanazawa University, Kakuma, Kanazawa (Japan); Rahman, M.M. [Department of Botany, Faculty of Biological Sciences, Jahangirnagar University, Savar, Dhaka (Bangladesh)

2008-06-15

Ferric (oxyhydro-)oxides (FeO{sub x}) precipitate in the rhizosphere at neutral or alkaline pH and are adsorbed on the plant root surfaces. Consequently, the higher binding affinity of arsenate to FeO{sub x} and the low iron phytoavailability of the precipitated FeO{sub x} make the phytoremediation of arsenic difficult. In the present study, the influence of chelating ligands on arsenic and iron uptake by hydroponically grown rice seedlings (Oryza sativa L.) was investigated. When chelating ligands were not treated to the growth medium, about 63 and 71% of the total arsenic and iron were distributed in the root extract (outer root surfaces) of rice, respectively. On the other hand, ethylenediaminetetraacetic acid (EDTA), ethylenediaminedisuccinic acid (EDDS) and hydroxyiminodisuccinic acid (HIDS) desorbed a significant amount of arsenic from FeO{sub x} of the outer root surfaces. Therefore, the uptake of arsenic and iron into the roots and their subsequent translocation to the shoots of the rice seedlings increased significantly. The order of increasing arsenic uptake by chelating ligands was HIDS > EDTA > EDDS. Methylglycinediacetic acid (MGDA) and iminodisuccinic acid (IDS) might not be effective in arsenic solubilization from FeO{sub x}. The results suggest that EDDS and HIDS would be a good and environmentally safe choice to accelerate arsenic phytoavailability in the phytoremediation process because of their biodegradability and would be a competent alternative to the widely used non-biodegradable and environmentally persistent EDTA. (Abstract Copyright [2008], Wiley Periodicals, Inc.)

Synthesis, biological evaluation and molecular modeling of 2-Hydroxyisoquinoline-1,3-dione analogues as inhibitors of HIV reverse transcriptase associated ribonuclease H and polymerase.

Science.gov (United States)

Tang, Jing; Vernekar, Sanjeev Kumar V; Chen, Yue-Lei; Miller, Lena; Huber, Andrew D; Myshakina, Nataliya; Sarafianos, Stefan G; Parniak, Michael A; Wang, Zhengqiang

2017-06-16

Human immunodeficiency virus (HIV) reverse transcriptase (RT) associated ribonuclease H (RNase H) remains the only virally encoded enzymatic function not clinically validated as an antiviral target. 2-Hydroxyisoquinoline-1,3-dione (HID) is known to confer active site directed inhibition of divalent metal-dependent enzymatic functions, such as HIV RNase H, integrase (IN) and hepatitis C virus (HCV) NS5B polymerase. We report herein the synthesis and biochemical evaluation of a few C-5, C-6 or C-7 substituted HID subtypes as HIV RNase H inhibitors. Our data indicate that while some of these subtypes inhibited both the RNase H and polymerase (pol) functions of RT, potent and selective RNase H inhibition was achieved with subtypes 8-9 as exemplified with compounds 8c and 9c. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

Electron-electron Bremsstrahlung for bound target electrons

International Nuclear Information System (INIS)

Haug, E.

2008-01-01

For the process of electron-electron (e-e) Bremsstrahlung the momentum and energy distributions of the recoiling electrons are calculated in the laboratory frame. In order to get the differential cross section and the photon spectrum for target electrons which are bound to an atom, these formulae are multiplied by the incoherent scattering function and numerically integrated over the recoil energy. The effect of atomic binding is most pronounced at low energies of the incident electrons and for target atoms of high atomic numbers. The results are compared to those of previous calculations. (authors)

Frequencies of HID-ion ampliseq ancestry panel markers among greenlanders

DEFF Research Database (Denmark)

Espregueira Themudo, Gonçalo; Smidt Mogensen, Helle; Børsting, Claus

2016-01-01

set of 89 individuals and a test set of 15 individuals. All loci showed genotype distributions consistent with Hardy-Weinberg expectations. Linkage disequilibrium tests indicated that 14 pairs of loci were in association in Greenlanders. Population assignment of the training set to populations...

Axial segregation in high intensity discharge lamps measured by laser absorption spectroscopy

NARCIS (Netherlands)

Stoffels, W.W.; Flikweert, A.J.; Nimalasuriya, T.; Groothuis, C.H.J.M.; Haverlag, M.; Kroesen, G.M.W.

2005-01-01

HID lamps containing rare earth additives (in our case dysprosium) show color separation because of axial segregation, caused by diffusion and convection. Two-dimensional atomic Dy density profiles are measured by means of laser absorption spectroscopy. The radially resolved atomic density

Results of the change of the lighting system in an institution of higher education; Resultados del cambio del sistema de iluminacion en una institucion de educacion superior

Energy Technology Data Exchange (ETDEWEB)

Torres P, Irene; Ambriz G, Juan Jose; Romero Paredes R, Hernando; Heras G, Francisco Javier [Universidad Autonoma Metropolitana. Iztapalapa (Mexico)

2003-07-01

In the Universidad Autonoma Metropolitana (UAM) actions have been made to diminish the energy consumption, one of them was the substitution and diminution of half of fluorescent lamps of 39W with ferromagnetic ballast for lamps of high electronic efficiency of 32W with electronic ballast. In this paper the results of the evaluation of the lighting level is presented after the indicated change, for which the measurement of the illumination level was made in the classrooms of 4 buildings of the UAM-1, as well as the calculation of the diminution of the electrical consumption for lighting taking into account previously measurements made of the consumption of electrical energy. The effect in the diminution of the electrical bill is significant, nevertheless, the lighting levels found are slightly insufficient. [Spanish] En la Universidad Autonoma Metropolitana se han realizado acciones enfocadas a disminuir el consumo de energia, una de ellas fue la sustitucion y disminucion a la mitad de lamparas fluorescentes de 39W con balastro ferromagnetico por lamparas de alta eficiencia de 32W con balastro electronico. En este trabajo se presentan los resultados de la evaluacion del nivel de iluminacion despues del cambio senalado, para lo cual se realizo la medicion del nivel de iluminacion en los salones de clase de 4 edificios de la UAM-I, asi como el calculo en la disminucion en el consumo electrico por iluminacion tomando en cuenta mediciones de consumo de energia electrica realizadas anteriormente. El efecto en la disminucion de la facturacion electrica es apreciable, sin embargo, los niveles de iluminacion encontrados son ligeramente insuficientes.

Interplay between electron-phonon and electron-electron interactions

International Nuclear Information System (INIS)

Roesch, O.; Gunnarsson, O.; Han, J.E.; Crespi, V.H.

2005-01-01

We discuss the interplay between electron-electron and electron-phonon interactions for alkali-doped fullerides and high temperature superconductors. Due to the similarity of the electron and phonon energy scales, retardation effects are small for fullerides. This raises questions about the origin of superconductivity, since retardation effects are believed to be crucial for reducing effects of the Coulomb repulsion in conventional superconductors. We demonstrate that by treating the electron-electron and electron-phonon interactions on an equal footing, superconductivity can be understood in terms of a local pairing. The Jahn-Teller character of the important phonons in fullerides plays a crucial role for this result. To describe effects of phonons in cuprates, we derive a t-J model with phonons from the three-band model. Using exact diagonalization for small clusters, we find that the anomalous softening of the half-breathing phonon as well as its doping dependence can be explained. By comparing the solution of the t-J model with the Hartree-Fock approximation for the three-band model, we address results obtained in the local-density approximation for cuprates. We find that genuine many-body results, due to the interplay between the electron-electron and electron-phonon interactions, play an important role for the the results in the t-J model. (copyright 2005 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

The Buffer and Backfill Handbook. Part 2: Materials and techniques

International Nuclear Information System (INIS)

Pusch, Roland

2001-12-01

Improved technology and prospection yielding more pure and homogeneous raw materials for preparing buffers and backfills will ultimately outdate the clays and ballast materials described in the present part of the Handbook. It describes experimentally investigated materials of potential use in repositories but other, more suitable materials will replace them in the future. The Handbook will hence have to be reviewed regularly, making room for superior materials in future, upgraded Handbook versions. Buffer is the term for dense clay used for embedment of canisters with highly radioactive waste, while backfill is soil used for filling tunnels and shafts in repositories. Examples of soil materials of potential use as buffers and backfills in repositories of KBS-3 type are described in this part of the Handbook. They are: smectitic clay materials intended for preparation of buffers (canister-embedding clay) and used as clay component in artificially prepared tunnel and shaft backfills consisting of mixtures of clay and ballast. Ballast materials intended for backfilling of tunnels and shafts and used as components of artificially prepared backfills. Smectitic natural clay soils intended for use as buffers and backfills. Very fine-grained smectite clay used as grout for sealing rock fractures. In this part of the Handbook for Buffers and Backfills, description of various candidate materials will be made with respect to their mineral composition and physical properties, with respect to the groundwater chemistry that can be expected in a deep repository in Swedish bedrock. Chapter 3 deals with smectitic clay materials intended for embedment of heat-producing canisters with highly radioactive waste. Focus is on the nature of the buffer constituents, i. e. the smectite content, the non-expanding clay minerals colloidal and the accessory non-clay minerals as well as amorphous matter and organic substances. The dominant part of the chapter describes the occurrence and origin

The Buffer and Backfill Handbook. Part 2: Materials and techniques

Energy Technology Data Exchange (ETDEWEB)

Pusch, Roland [Geodevelopment AB, Lund (Sweden)

2001-12-01

Improved technology and prospection yielding more pure and homogeneous raw materials for preparing buffers and backfills will ultimately outdate the clays and ballast materials described in the present part of the Handbook. It describes experimentally investigated materials of potential use in repositories but other, more suitable materials will replace them in the future. The Handbook will hence have to be reviewed regularly, making room for superior materials in future, upgraded Handbook versions. Buffer is the term for dense clay used for embedment of canisters with highly radioactive waste, while backfill is soil used for filling tunnels and shafts in repositories. Examples of soil materials of potential use as buffers and backfills in repositories of KBS-3 type are described in this part of the Handbook. They are: smectitic clay materials intended for preparation of buffers (canister-embedding clay) and used as clay component in artificially prepared tunnel and shaft backfills consisting of mixtures of clay and ballast. Ballast materials intended for backfilling of tunnels and shafts and used as components of artificially prepared backfills. Smectitic natural clay soils intended for use as buffers and backfills. Very fine-grained smectite clay used as grout for sealing rock fractures. In this part of the Handbook for Buffers and Backfills, description of various candidate materials will be made with respect to their mineral composition and physical properties, with respect to the groundwater chemistry that can be expected in a deep repository in Swedish bedrock. Chapter 3 deals with smectitic clay materials intended for embedment of heat-producing canisters with highly radioactive waste. Focus is on the nature of the buffer constituents, i. e. the smectite content, the non-expanding clay minerals colloidal and the accessory non-clay minerals as well as amorphous matter and organic substances. The dominant part of the chapter describes the occurrence and origin

GPR Laboratory Tests For Railways Materials Dielectric Properties Assessment

Directory of Open Access Journals (Sweden)

Francesca De Chiara

2014-10-01

Full Text Available In railways Ground Penetrating Radar (GPR studies, the evaluation of materials dielectric properties is critical as they are sensitive to water content, to petrographic type of aggregates and to fouling condition of the ballast. Under the load traffic, maintenance actions and climatic effects, ballast condition change due to aggregate breakdown and to subgrade soils pumping, mainly on existing lines with no sub ballast layer. The main purpose of this study was to validate, under controlled conditions, the dielectric values of materials used in Portuguese railways, in order to improve the GPR interpretation using commercial software and consequently the management maintenance planning. Different materials were tested and a broad range of in situ conditions were simulated in laboratory, in physical models. GPR tests were performed with five antennas with frequencies between 400 and 1800 MHz. The variation of the dielectric properties was measured, and the range of values that can be obtained for different material condition was defined. Additionally, in situ GPR measurements and test pits were performed for validation of the dielectric constant of clean ballast. The results obtained are analyzed and the main conclusions are presented herein.

Plankton And Heavy Metal Correlation From Commercial Vessels In Port Of Tanjung Emas Semarang

Science.gov (United States)

Tjahjono, Agus; Bambang, Aziz Nur; Anggoro, Sutrisno

2018-02-01

The commercial vessels activity have a big role to increase the flow of number of cargoes from a port to another port. However, the impact of these activities are the disposal of ballast water from port area to the destination port. The purpose of this research was to analyze the correlation of phytoplankton, zooplankton, and heavy metal which were contained inside the ballast water of commercial vessel towards in waters of the port of Tanjung Emas Semarang. The concentration of heavy metal either from commercial vessels or the waters in port area analyzed by Atomic Absorption Spectrophotometer (AAS). The result showed that the correlation of zooplankton and phytoplankton in the water ballast at commercial vessels have a medium correlation to zooplankton and phytoplankton in waters of Port of Tanjung Emas Semarang (PTES) were 48.9% and 58.3%. Correlation of heavy metal Cd, Zn, Cu, Zn and Pb in ballast water of commercial vessel toward each metal in waters of PTES area has a strong correlation in contribution were 76.7%, 75.6%, 71.4% and 73.8%. It showed us that the loading activity of commercial vessels in port are contributed towards the pollution in waters.

Development of an electronic converter with maximum power point tracking for photovoltaic systems applied to rural electrification; Desenvolvimento de conversor eletronico para maxima transferencia de potencia em sistemas fotovoltaicos aplicados a eletrificacao rural

Energy Technology Data Exchange (ETDEWEB)

Machado Neto, Lauro de Vilhena Brandao [Pontificia Universidade Catolica de Minas Gerais (PUC-Minas), Belo Horizonte, MG (Brazil); Cabral, Claudia Valeria Tavora; Oliveira Filho, Delly [Universidade Federal de Vicosa (UFV), MG (Brazil); Diniz, Antonia Sonia Alves Cardoso [Companhia Energetica de Minas Gerais (CEMIG), Belo Horizonte, MG (Brazil); Cortizo, Porfirio Cabaleiro [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil)

2004-07-01

The maximization of the efficiency in the electric energy conversion is essential to the developing of technical and economic viability of photovoltaic solar energy systems. This paper presents the development of an electronic converter with maximum power point tracking for photovoltaic systems applied to rural electrification. The standalone photovoltaic system used is similar to the systems installed by Companhia Energetica de Minas Gerais - CEMIG in the schools of isolated communities, inside the Solar Light Program. Initially were developed test procedures of the equipment used in the system like photovoltaic generators, electronic ballasts, inverters, charge controllers and batteries, covering minimum performance requirements and in compliance with national and international standards, as possible, due to the instrumentation availability. A data acquisition system was assembled to monitoring the photovoltaic system. A simulation of the system was implemented and the aims were to optimize the project and carry out a comparative study with the monitoring results. The converter with maximum power point tracking consists of a direct current converter in the buck configuration and the control algorithm was implemented in a micro controller, being the first results presented here. After finished the prototype, it will be incorporated in the photovoltaic system and will be accomplished a study of the technical and economic viability. The first results of the tests, of the monitoring and of the converter with maximum power point tracking are helping the sustainability of the systems installed by CEMIG, funding the government initiatives in the quality control of equipment and promoting the development of national technology. (author)

Untitled

Indian Academy of Sciences (India)

AAA. E. Tethys-Himalaya. (Paleozoic-Eocene). - Zanskar Shear Zone (ZSZ). Higher Himalaya Crystalline. Dras Wolcanics ha-. Ophiolite Melange Main Central Thrust (MCT). (Jurassic - Cretaceous) HID Kishtwar Window. Lesser Himalaya. "T" indus Thrust -A-A- Main Boundary Thrust (MBT). BSS Siwaliks Molasse (Neogene).

Effect of inflammatory attacks in the classical type hyper-IgD syndrome on immunoglobulin D, cholesterol and parameters of the acute phase response.

NARCIS (Netherlands)

Simon, A.; Bijzet, J.; Voorbij, H.A.; Mantovani, A.; Meer, J.W.M. van der; Drenth, J.P.H.

2004-01-01

BACKGROUND: Classical type hyper-immunoglobulin D (IgD) syndrome (HIDS) is an hereditary auto-inflammatory disorder, characterized by recurrent episodes of fever, lymphadenopathy, abdominal distress and a high serum concentration of IgD. It is caused by mevalonate kinase deficiency. OBJECTIVE: To

75 FR 22031 - Energy Conservation Program for Consumer Products and Certain Commercial and Industrial Equipment...

Science.gov (United States)

2010-04-27

..., including induction and fluorescent. Non-HID technologies are achieving market penetration in lighting... and the national impacts analysis. DOE developed end-user prices, including a contractor mark-up rate... inputs: Estimated average annual operating hours and lamp lifetimes; estimated average prices for lamps...

Unge bliver ofre for kortsigtet rekruttering

DEFF Research Database (Denmark)

Nielsen, Rikke Kristine

2013-01-01

Rip-Rap-Rup-effekt: Det er fristende at hyre en kandidat med 10-20-30 års ballast fra arbejdsmarkedet. Men er det langsigtet at se bort fra de unge og mindre erfarne?......Rip-Rap-Rup-effekt: Det er fristende at hyre en kandidat med 10-20-30 års ballast fra arbejdsmarkedet. Men er det langsigtet at se bort fra de unge og mindre erfarne?...

Design and testing of a separate-type lighting system using solar energy and cold-cathode fluorescent lamps

Energy Technology Data Exchange (ETDEWEB)

Yang, J.-P. [Department of Electrical Engineering, China Institute of Technology, Taipei, Taiwan 115, Taiwan (China)]. E-mail: april4120@tp.edu.tw; Hsiao, H.-C. [Department of Electrical Engineering, National Taiwan University of Science and Technology, Taipei, Taiwan 106, Taiwan (China)]. E-mail: hsiao@mouse.ee.ntust.edu.tw

2007-01-15

This paper presents a solar-powered lighting system, using cold-cathode fluorescent-lamps (CCFLs), with its battery-charging circuit and lamp-ignition circuit being separated so that its solar panels can be installed at any distance deemed necessary away from the lighting site in order to receive the maximum solar energy available. This system adopts the maximum-power point tracking (MPPT) method to control the power output of the solar panels and uses the zero-voltage switching (ZVS) DC-DC converter, as the charging circuit, to increase the panels' power generation efficiency and the charging circuit's conversion efficiency. The electronic ballast circuit for the CCFL is constructed with a half-bridge inverter, a resonant inductor, and a Rosen-type piezoelectric transformer, which forms a piezoelectric resonant-type inverter: to simplify the circuitry and to improve the power conversion efficiency, the ballast circuit is designed to directly step up the battery voltage in igniting the lamp. We also establish the transmission-parameter model for the piezoelectric resonant-type inverter to provide the base for the electric-power circuit design. Our experimental results indicate that the proposed system possesses some advantages, such as greater energy efficiency, circuitry simplicity, and so on, and is suitable for night lighting in house yards, parks and advertising panels.

Design and testing of a separate-type lighting system using solar energy and cold-cathode fluorescent lamps

International Nuclear Information System (INIS)

Yang, J.-P.; Hsiao, H.-C.

2007-01-01

This paper presents a solar-powered lighting system, using cold-cathode fluorescent-lamps (CCFLs), with its battery-charging circuit and lamp-ignition circuit being separated so that its solar panels can be installed at any distance deemed necessary away from the lighting site in order to receive the maximum solar energy available. This system adopts the maximum-power point tracking (MPPT) method to control the power output of the solar panels and uses the zero-voltage switching (ZVS) DC-DC converter, as the charging circuit, to increase the panels' power generation efficiency and the charging circuit's conversion efficiency. The electronic ballast circuit for the CCFL is constructed with a half-bridge inverter, a resonant inductor, and a Rosen-type piezoelectric transformer, which forms a piezoelectric resonant-type inverter: to simplify the circuitry and to improve the power conversion efficiency, the ballast circuit is designed to directly step up the battery voltage in igniting the lamp. We also establish the transmission-parameter model for the piezoelectric resonant-type inverter to provide the base for the electric-power circuit design. Our experimental results indicate that the proposed system possesses some advantages, such as greater energy efficiency, circuitry simplicity, and so on, and is suitable for night lighting in house yards, parks and advertising panels

Electronic emission and electron guns

International Nuclear Information System (INIS)

Roy, Amitava

2010-01-01

This paper reviews the process of electron emission from metal surface. Although electrons move freely in conductors like metals, they normally do not leave the metal without some manipulation. In fact, heating and bombardment are the two primary ways in which electrons are emitted through the use of a heating element behind the cathode (termed thermionic emission) or as a result of bombardment with a beam of electrons, ions, or metastable atoms (termed secondary emission). Another important emission mechanism called Explosive Electron Emission (EEE) is also often used in various High Voltage Pulse Power Systems to generate very high current (few hundreds of kA) pulsed electron beams. The electron gun is the device in that it shoots off a continuous (or pulsed) stream of electrons. A brief idea about the evolution of the electron gun components and their basis of functioning are also discussed. (author)

Tie-ballast interaction.

Science.gov (United States)

2015-09-28

Improvements in railroad efficiency in the future may likely require higher passenger train speeds and heavier freight axle loads. As the demand for more efficient rail transportation grows, so does the need for higher performance and lower maintenan...

When Distribution of Tasks and Skills Are Fundamentally Problematic

DEFF Research Database (Denmark)

Matthiesen, Stina; Bjørn, Pernille

2017-01-01

within a global software project, which relied heavily on feedback from mundane project tools utilized for everyday coordination and monitoring. Our study reveals that these tools hid serious issues relating to both the distribution of sociotechnical skills and a discharge of accountability in task...

78 FR 51463 - Energy Conservation Program: Energy Conservation Standards for Metal Halide Lamp Fixtures

Science.gov (United States)

2013-08-20

... merging the metal halide lamp fixture and the high-intensity discharge (HID) lamp rulemakings. This NOPR... Conservation Program: Energy Conservation Standards for Metal Halide Lamp Fixtures; Proposed Rule #0;#0;Federal...: Energy Conservation Standards for Metal Halide Lamp Fixtures AGENCY: Office of Energy Efficiency and...

High Output LED-Based Profile Lighting Fixture

DEFF Research Database (Denmark)

Török, Lajos; Beczkowski, Szymon; Munk-Nielsen, Stig

2011-01-01

Recent developments in power light emitting diode (LED) industry have made LEDs suitable for being efficiently used in high intensity lighting fixtures instead of the commonly used high intensity discharge (HID) lamps. A high output LEDbased profile-light fixture is presented in this paper...

Born-Oppenheimer Dynamics, Electronic Friction, and the Inclusion of Electron-Electron Interactions

Science.gov (United States)

Dou, Wenjie; Miao, Gaohan; Subotnik, Joseph E.

2017-07-01

We present a universal expression for the electronic friction as felt by a set of classical nuclear degrees of freedom (DOFs) coupled to a manifold of quantum electronic DOFs; no assumptions are made regarding the nature of the electronic Hamiltonian and electron-electron repulsions are allowed. Our derivation is based on a quantum-classical Liouville equation for the coupled electronic-nuclear motion, followed by an adiabatic approximation whereby electronic transitions are assumed to equilibrate faster than nuclear movement. The resulting form of friction is completely general, but does reduce to previously published expressions for the quadratic Hamiltonian (i.e., Hamiltonians without electronic correlation). At equilibrium, the second fluctuation-dissipation theorem is satisfied and the frictional matrix is symmetric. To demonstrate the importance of electron-electron correlation, we study electronic friction within the Anderson-Holstein model, where a proper treatment of electron-electron interactions shows signatures of a Kondo resonance and a mean-field treatment is completely inadequate.

Device for conducting a cryogenic medium

International Nuclear Information System (INIS)

Beck, K.

1978-01-01

The seal between the fixed and the rotating part of the turbine generator consists of several packing washers arranged one behind the other in axial direction. The remote outer parts of the packing washers contain grooves in which lead balls are provided for ballast. By suitable selection of the ballast mass a predetermined radial expansion force caused by a corresponding contrifugal force may be applied to each sealing element. (DG) [de

Fabrication of high-power piezoelectric transformers using lead-free ceramics for application in electronic ballasts.

Science.gov (United States)

Yang, Song-Ling; Chen, Shih-Ming; Tsai, Cheng-Che; Hong, Cheng-Shong; Chu, Sheng-Yuan

2013-02-01

CuO is doped into (Na(0.5)K(0.5))NbO(3) (NKN) ceramics to improve the piezoelectric properties and thus obtain a piezoelectric transformer (PT) with high output power. In X-ray diffraction patterns, the diffraction angles of the CuO-doped NKN ceramics shift to lower values because of an expansion of the lattice volume, thus inducing oxygen vacancies and enhancing the mechanical quality factor. A homogeneous microstructure is obtained when NKN is subjected to CuO doping, leading to improved electrical properties. PTs with different electrode areas are fabricated using the CuO-doped NKN ceramics. Considering the efficiency, voltage gain, and temperature rise of PTs at a load resistance of 1 kΩ, PTs with an electrode with an inner diameter of 15 mm are combined with the circuit design for driving a 13-W T5 fluorescent lamp. A temperature rise of 6°C and a total efficiency of 82.4% (PT and circuit) are obtained using the present PTs.

Generalized Nevanlinna functions with essentially positive spectrum

NARCIS (Netherlands)

Kaltenbaeck, Michael; Winkler, Henrik; Woracek, Harald

2006-01-01

We introduce an indefinite analogue of the so-called Stieltjes class and provide some basic results on this hid finite Stieltjes class. Among them: The relation between the functions q(z), zq(z) and zq(z(2)), limit properties, a distributional representation. These results generalize well known

76 FR 77914 - Energy Conservation Program for Certain Commercial and Industrial Equipment: Test Procedures for...

Science.gov (United States)

2011-12-15

... lifetime. Correlated color temperature (CCT) and color rendering index (CRI) would also be measured as potential means to delineate equipment classes for HID lamps. This notice of proposed rulemaking (NOPR) also... Conditions a. Ambient Conditions i. Ambient Test Temperature ii. Air Speed b. Power Supply Characteristics i...

Time resolved Thomson scattering measurements on a high pressure mercury lamp

NARCIS (Netherlands)

Vries, de N.; Zhu, Xiao-Yan; Kieft, E.R.; Mullen, van der J.J.A.M.

2005-01-01

Time resolved Thomson scattering (TS) measurements have been performed on an ac driven high pressure mercury lamp. For this high intensity discharge (HID) lamp, TS is coherent and a coherent fitting routine, including rotational Raman calibration, was used to determine ne and Te from the measured

Self Righting Life Raft

Science.gov (United States)

1982-01-01

The Givens Buoy Raft was designed and manufactured for inventor Jim Givens of Givens Marine Survival Co. Inc., by RPR Industries, Inc. The Raft consists of a canopied topside and an underwater hemispheric ballast chamber. It has a heavy ballast stabilization system, adopted from NASA technology, which negates the capsizing problem. A "flapper valve" admits large amounts of water to the hemisphere chamber providing ballast to keep the center of gravity constant; stabilization system compensates for changes in wave angle and weight shifting of raft occupants. Mr. Givens has an exclusive patent license for use of the NASA technology. Produced in various sizes, capacities range from six to 20 persons. Raft is housed in a canister, available in several configurations. A pull on a line triggers the automatic inflation process, which takes 12 seconds. The raft has been credited with saving 230 lives in the last five years. It has found wide acceptance with operators of fishing boats, pleasure craft and other vessels. The Coast Guard is purchasing the rafts for use on its rescue helicopters and the Navy has a development program to adapt the system. The Coast Guard last year announced a proposed amendment of its regulations that would require large ballast chambers on inflatable life rafts.

Recent changes in federal PCB regulations

International Nuclear Information System (INIS)

Ewing, H.

1995-01-01

An overview of the federal regulations dealing with PCBs, the draft PCB Transformer Decontamination Standards and Protocols, and the Practice of Ballast Splitting was given. Answers were provided to practical questions concerning the regulations, specifically, responsibility for storage, labelling requirements, waste export regulations, treatment and destruction standards, transformer decontamination, decontamination standards, and the practice of ballast splitting into PCB and non-PCB materials. Details of sampling procedures and sample handling were also described

Hyper-IgD syndrome or mevalonate kinase deficiency.

NARCIS (Netherlands)

Stoffels, M.; Simon, A.

2011-01-01

PURPOSE OF REVIEW: The hyper-IgD and periodic fever syndrome (HIDS) is one of the classical monogenetic hereditary autoinflammatory disorders, and together with the more severe mevalonic aciduria it is also known as 'mevalonate kinase deficiency' (MKD). In this study, we will give an overview of the

77 FR 11785 - Energy Conservation Program: Public Meeting and Availability of the Framework Document for High...

Science.gov (United States)

2012-02-28

... standards for high-intensity discharge (HID) lamps. Accordingly, DOE will hold a public meeting to discuss..._standards/commercial/high_intensity_discharge_lamps.html . DATES: The Department will hold a public meeting... Technologies Program, Mailstop EE-2J, Framework Document for High-Intensity Discharge Lamps, EERE-2010-BT-STD...

U.S. EPA, Pesticide Product Label, PROKIL PARATHION 4 LB, 01/06/1988

Science.gov (United States)

2011-04-21

... m:AIl [lmRE l.ARD .. II,.> "Ilirtly III acca,· .Irlll':a with dUllyers. ... f .• ,ricI'!'lIHII r.xlen~inn ;'l'rvIU~ ·(I.,ePII""I. ~:' . lhL· I.Sl::le. BEANS: "'I,hid~i. r;.!oi'f1·lli'.;. ...

Effective electron-electron and electron-phonon interactions in the Hubbard-Holstein model

International Nuclear Information System (INIS)

Aprea, G.; Di Castro, C.; Grilli, M. . E-mail marco.grilli@roma1.infn.it; Lorenzana, J.

2006-01-01

We investigate the interplay between the electron-electron and the electron-phonon interaction in the Hubbard-Holstein model. We implement the flow-equation method to investigate within this model the effect of correlation on the electron-phonon effective coupling and, conversely, the effect of phonons in the effective electron-electron interaction. Using this technique we obtain analytical momentum-dependent expressions for the effective couplings and we study their behavior for different physical regimes. In agreement with other works on this subject, we find that the electron-electron attraction mediated by phonons in the presence of Hubbard repulsion is peaked at low transferred momenta. The role of the characteristic energies involved is also analyzed

Paternity tests in Mexico: Results obtained in 3005 cases.

Science.gov (United States)

García-Aceves, M E; Romero Rentería, O; Díaz-Navarro, X X; Rangel-Villalobos, H

2018-04-01

National and international reports regarding the paternity testing activity scarcely include information from Mexico and other Latin American countries. Therefore, we report different results from the analysis of 3005 paternity cases analyzed during a period of five years in a Mexican paternity testing laboratory. Motherless tests were the most frequent (77.27%), followed by trio cases (20.70%); the remaining 2.04% included different cases of kinship reconstruction. The paternity exclusion rate was 29.58%, higher but into the range reported by the American Association of Blood Banks (average 24.12%). We detected 65 mutations, most of them involving one-step (93.8% and the remaining were two-step mutations (6.2%) thus, we were able to estimate the paternal mutation rate for 17 different STR loci: 0.0018 (95% CI 0.0005-0.0047). Five triallelic patterns and 12 suspected null alleles were detected during this period; however, re-amplification of these samples with a different Human Identification (HID) kit confirmed the homozygous genotypes, which suggests that most of these exclusions actually are one-step mutations. HID kits with ≥20 STRs detected more exclusions, diminishing the rate of inconclusive results with isolated exclusions (Powerplex 21 kit (20 STRs) and Powerplex Fusion kit (22 STRs) offered similar PI (p = 0.379) and average number of exclusions (PE) (p = 0.339) when a daughter was involved in motherless tests. In brief, besides to report forensic parameters from paternity tests in Mexico, results describe improvements to solve motherless paternity tests using HID kits with ≥20 STRs instead of one including 15 STRs. Copyright © 2018 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

Le califat méditerranéen et maritime de Denia

Directory of Open Access Journals (Sweden)

Travis Bruce

2012-02-01

Full Text Available La désintégration du califat de Cordoue au début du XIe siècle a ouvert la porte à une nouvelle appréhension de l’espace politique et religieux islamique. Mujāhid al-‘Āmirī, souverain de la taifa de Denia sur la côte orientale, s’est lancé dans la création d’un califat ex novo sur la frontière maritime islamique. Rappelant la politique des premiers califes umayyades, Mujāhid a pensé son état en termes de jihād et d’expansion territoriale, et non pas en termes d’appropriation d’un espace déjà islamisé. La singularité de cette ambition fut double. D’une part, la création d’un califat afin de légitimer ce jihād maritime renforce l’idée d’une action de lutte contre le dār al-ḥarb et non pas seulement une piraterie particulièrement agressive. D’autre part, l’espace sacralisé par Mujāhid et le jihād mené sous son autorité comprenait autant les routes maritimes que les côtes et les îles qui le délimitaient. Le califat de Denia se solda en échec, mais la guerre sainte maritime qu’il avait inaugurée se poursuivit ; la taifa de Denia demeura un avant-poste d’Islam sur la frontière maritime, ses navires étaient des extensions réticulaires et mobiles de l’espace islamique.

Electron-electron coincidence spectroscopies at surfaces

International Nuclear Information System (INIS)

Stefani, G.; Iacobucci, S.; Ruocco, A.; Gotter, R.

2002-01-01

In the past 20 years, a steadily increasing number of electron-electron coincidence experiments on atoms and molecules have contributed to a deeper understanding of electron-electron correlation effects. In more recent years this technique has been extended to the study of solid surfaces. This class of one photon IN two electrons OUT experiments will be discussed with an emphasis on grazing incidence geometry, that is expected to be particularly suited for studying surfaces. The crucial question of which is the dominant mechanism that leads to ejection of pairs of electron from the surface will be addressed. It will be shown that, depending on the kinematics chosen, the correlated behaviour of the pairs of electrons detected might be singled out from independent particle one

Electron distribution function in electron-beam-excited plasmas

International Nuclear Information System (INIS)

Brau, C.A.

1976-01-01

In monatomic plasmas excited by high-intensity relativistic electron beams, the electron secondary distribution function is dominated by elastic electron-electron collisions at low electron energies and by inelastic electron-atom collisions at high electron energies (above the excitation threshold). Under these conditions, the total rate of excitation by inelastic collisions is limited by the rate at which electron-electron collisions relax the distribution function in the neighborhood of the excitation threshold. To describe this effect quantitatively, an approximate analytic solution of the electron Boltzmann equation is obtained, including both electron-electron and inelastic collisions. The result provides a simple formula for the total rate of excitation

Statistical modelling of Ion PGM HID STR 10-plex MPS Data

DEFF Research Database (Denmark)

Vilsen, Søren B; Tvedebrink, Torben; Mogensen, Helle Smidt

2017-01-01

sequences using dynamic thresholds created by fitting the distribution of the non-systematic erroneous sequences. We found that, due to MID sampling, the average coverage on a marker could not be used as an apt predictor of the amount of template DNA. The parental LUS was shown to be better predictor...

Hard electronics; Hard electronics

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

Hard material technologies were surveyed to establish the hard electronic technology which offers superior characteristics under hard operational or environmental conditions as compared with conventional Si devices. The following technologies were separately surveyed: (1) The device and integration technologies of wide gap hard semiconductors such as SiC, diamond and nitride, (2) The technology of hard semiconductor devices for vacuum micro- electronics technology, and (3) The technology of hard new material devices for oxides. The formation technology of oxide thin films made remarkable progress after discovery of oxide superconductor materials, resulting in development of an atomic layer growth method and mist deposition method. This leading research is expected to solve such issues difficult to be easily realized by current Si technology as high-power, high-frequency and low-loss devices in power electronics, high temperature-proof and radiation-proof devices in ultimate electronics, and high-speed and dense- integrated devices in information electronics. 432 refs., 136 figs., 15 tabs.

Photovoltaic systems on flat roofs. A new approach; Photovoltaique sur toits plats. Une nouvelle approche. Rapport final

Energy Technology Data Exchange (ETDEWEB)

Roecker, C.; Bonvin, J.; Muller, A.

1999-06-01

Flat roofs are among the best choices to mount photovoltaics on buildings. Nevertheless, standard solutions in use till the mid-nineties were quite poor, as far as price, aesthetics and ease of maintenance were concerned. This report presents, following a comprehensive typology study of flat roofs, a series of new and innovative solutions, fully developed and tested. There are three main system groups, differing essentially by the ballasting method used to keep the panels on the roof: (i) the SOFREL family, using concrete blocs weighting; (ii) the SOLBAC family, using existing ballast weighting; and (iii) the SOLGREEN family, using ballast and earth weighting. Some more systems, not finalised, are also described, giving some hints for possible new developments. To conclude, this project has brought three main systems, all three already or soon commercially available, allowing a simple and easy mounting of photovoltaic panels on any flat roof type. (author)

Interaction of multiple plasma plumes in an atmospheric pressure plasma jet array

International Nuclear Information System (INIS)

Ghasemi, M; Olszewski, P; Bradley, J W; Walsh, J L

2013-01-01

Plasma jet arrays are considered a viable means to enhance the scale of a downstream surface treatment beyond that possible using a single plasma jet. Of paramount importance in many processing applications is the uniformity of the plasma exposure on the substrate, which can be compromised when multiple plasma jets are arranged in close proximity due to their interaction. This contribution explores a dielectric barrier plasma jet array consisting of multiple individually ballasted jets. It is shown that capacitive ballasting is a promising technique to allow simultaneous operation of the plasma plumes without the losses associated with resistive ballasting. The interaction between adjacent plasma plumes and the background gas is investigated with Schlieren imaging; it is shown that the strong repulsive force between each plasma plume causes a divergence in propagation trajectory and a reduction in the laminar flow length with significant ramifications for any downstream surface treatment.

3D dysprosium density in the metal-halide lamp measured by emission and laser absorption spectroscopy in a centrifuge at 1-10g

NARCIS (Netherlands)

Flikweert, A.J.; Nimalasuriya, T.; Thubé, G.M.; Kroesen, G.M.W.; Stoffels, W.W.

2007-01-01

The metal-halide lamp is a High Intensity Discharge (HID) lamp with a high efficiency. The salt additive (DyI3) acts as prime radiator. The present lamp suffers from non-uniform light output, caused by diffusion and convection processes. To gain a better understanding of the lamp, the convection is

High-throughput sequencing of forensic genetic samples using punches of FTA cards with buccal swabs

DEFF Research Database (Denmark)

Kampmann, Marie-Louise; Buchard, Anders; Børsting, Claus

2016-01-01

Here, we demonstrate that punches from buccal swab samples preserved on FTA cards can be used for high-throughput DNA sequencing, also known as massively parallel sequencing (MPS). We typed 44 reference samples with the HID-Ion AmpliSeq Identity Panel using washed 1.2 mm punches from FTA cards...

Prophylactic anti-D preparations display variable decreases in Fc-fucosylation of anti-D.

NARCIS (Netherlands)

Kapur, R.; Della Valle, L.; Verhagen, O.J.; Hipgrave Ederveen, A.; Ligthart, P.; de Haas, M.; Kumpel, B.; Wuhrer, M.; van der Schoot, C.E.; Vidarsson, G.

2015-01-01

Background RhIG is obtained from hyperimmunized healthy anti-D donors (HIDs) boosted with D+ red blood cells (RBCs). One hypothesis for its mechanism of action is fast clearance of opsonized D+ RBCs through Fcγ receptor (FcγR)III. Levels of immunoglobulin (Ig)G Fc-fucosylation influence interactions

Prophylactic anti-D preparations display variable decreases in Fc-fucosylation of anti-D

NARCIS (Netherlands)

Kapur, Rick; Della Valle, Luciana; Verhagen, Onno J. H. M.; Hipgrave Ederveen, Agnes; Ligthart, Peter; de Haas, Masja; Kumpel, Belinda; Wuhrer, Manfred; van der Schoot, C. Ellen; Vidarsson, Gestur

2015-01-01

RhIG is obtained from hyperimmunized healthy anti-D donors (HIDs) boosted with D+ red blood cells (RBCs). One hypothesis for its mechanism of action is fast clearance of opsonized D+ RBCs through Fcγ receptor (FcγR)III. Levels of immunoglobulin (Ig)G Fc-fucosylation influence interactions with

ARGES: Radial segregation and helical instabilities in metal halide lamps studied under microgravity conditions in the international space station

NARCIS (Netherlands)

Kroesen, G.M.W.; Haverlag, M.; Dekkers, Erwin; Moerel, Jovita; Kluijver, de R.; Brinkgreve, P.; Groothuis, C.H.J.M.; Mullen, van der J.J.A.M.; Stoffels, W.W.; Keijser, R.; Bax, M.W.G.; van den Akker, D.; Schiffelers, G.C.S.; Kemps, P.C.M.; van den Hout, F.H.J.; Kuipers, A.

2005-01-01

HID lamps (High-Intensity Discharge) are gaining ground in the lighting industry because of their very high energy efficiency (up to 40%). In these lamps, which are operated in the arc regime and which are contained in a ceramic balloon, filled with argon or xenon, mercury, and salts of various rare

The market effects of SDG and E's and PG and E's commercial lighting efficiency programs

Energy Technology Data Exchange (ETDEWEB)

Rosenberg, M.; Rufo, M.; Besa, A.; O' Drain, M.

1998-07-01

The paper summarizes the methods and findings of a project to assess the market effects of commercial lighting efficiency programs sponsored by San Diego Gas & Electric and Pacific Gas and Electric. The study focused on effects on the markets for efficient fluorescent lighting components: electronic ballasts, T-8 lamps, and fixtures that integrate those technologies. The research for the project consisted of surveys of representative samples of end-users in the sponsors' service territories and a non-program area in which no utility DSM program had operated, in-depth interviews with manufacturers and other supply side actors in both the sponsor and non-program areas, and review of secondary sources. The study found that the sponsors' programs, as part of a larger national utility effort, had a significant effect on levels of customer demand for efficient ballasts and lamps at the national as well as regional level. The sponsors programs also had important effects on the local markets, such as increased promotion by designers and contractors and very rapid up swings in demand among certain sectors of end-users. Market share for efficient fluorescent components continues to increase in the face of decreased utility program support. This and other evidence suggests that some of the market effects of the sponsors' programs will be durable.

Electron radiography

Science.gov (United States)

Merrill, Frank E.; Morris, Christopher

2005-05-17

A system capable of performing radiography using a beam of electrons. Diffuser means receive a beam of electrons and diffuse the electrons before they enter first matching quadrupoles where the diffused electrons are focused prior to the diffused electrons entering an object. First imaging quadrupoles receive the focused diffused electrons after the focused diffused electrons have been scattered by the object for focusing the scattered electrons. Collimator means receive the scattered electrons and remove scattered electrons that have scattered to large angles. Second imaging quadrupoles receive the collimated scattered electrons and refocus the collimated scattered electrons and map the focused collimated scattered electrons to transverse locations on an image plane representative of the electrons' positions in the object.

Electron transfer from electronic excited states to sub-vacuum electron traps in amorphous ice

International Nuclear Information System (INIS)

Vichnevetski, E.; Bass, A.D.; Sanche, L.

2000-01-01

We investigate the electron stimulated yield of electronically excited argon atoms (Ar * ) from monolayer quantities of Ar deposited onto thin films of amorphous ice. Two peaks of narrow width ( - electron-exciton complex into exciton states, by the transfer of an electron into a sub-vacuum electron state within the ice film. However, the 10.7 eV feature is shifted to lower energy since electron attachment to Ar occurs within small pores of amorphous ice. In this case, the excess electron is transferred into an electron trap below the conduction band of the ice layer

The Body As Proof: Franklin D. Roosevelt's Preparations for the 1932 Presidential Campaign.

Science.gov (United States)

Kiewe, Amos

1999-01-01

Discusses how prior to the 1932 presidential campaign, Governor Roosevelt sought to dispel suspicion that he was physically unfit to become President; and though he never hid his disability, he minimized his appearance as a disabled person. Describes how Roosevelt arranged for the publication of a medical examination as proof that he was…

Effects of creating two forest structures and using prescribed fire on coarse woody debris in northeastern California, USA

Science.gov (United States)

Fabian C. C. Uzoh; Carl N. Skinner

2009-01-01

Little is known about the dynamics of coarse woody debris (CWD) in forests that were originally characterized by frequent, low-moderate intensity fires. We investigated effects of prescribed burning at the Blacks Mountain Experimental Forest in northeastern California following creation of two stand structure conditions: 1) high structural diversity (HiD) that included...

Planktonic food web structure along the Sau Reservoir (Spain) in summer 1997

Czech Academy of Sciences Publication Activity Database

Comerma, M.; García, J. C.; Armengol, J.; Romero, M.; Šimek, Karel

2001-01-01

Roč. 86, č. 2 (2001), s. 195-209 ISSN 1434-2944 R&D Projects: GA ČR GA206/99/0028 Grant - others:CICYT(XE) HID96-1374-CO2; CIRIT(XE) 1997SGR-122 Keywords : longitudinal gradients * reservoir * bacterial production Subject RIV: EE - Microbiology, Virology Impact factor: 0.725, year: 2001

Monte Carlo study of electron relaxation in graphene with spin polarized, degenerate electron gas in presence of electron-electron scattering

Science.gov (United States)

Borowik, Piotr; Thobel, Jean-Luc; Adamowicz, Leszek

2017-12-01

The Monte Carlo simulation method is applied to study the relaxation of excited electrons in monolayer graphene. The presence of spin polarized background electrons population, with density corresponding to highly degenerate conditions is assumed. Formulas of electron-electron scattering rates, which properly account for electrons presence in two energetically degenerate, inequivalent valleys in this material are presented. The electron relaxation process can be divided into two phases: thermalization and cooling, which can be clearly distinguished when examining the standard deviation of electron energy distribution. The influence of the exchange effect in interactions between electrons with parallel spins is shown to be important only in transient conditions, especially during the thermalization phase.

Influence of Surface Abrasion on Creep and Shrinkage of Railway Prestressed Concrete Sleepers

Science.gov (United States)

Li, Dan; Ngamkhanong, Chayut; Kaewunruen, Sakdirat

2017-10-01

Ballasted railway track is very suitable for heavy-rail networks because of its many superior advantages in design, construction, short- and long-term maintenance, sustainability, and life-cycle cost. The sleeper, which supports rail and distributes loads from rail to ballast, is a very important component of rail track system. Prestressed concrete is very popular used in manufacturing sleepers. Therefore, improved knowledge about design techniques for prestressed concrete (PC) sleepers has been developed. However, the ballast angularity causes differential abrasions on the soffit or bottom surface of sleepers. Furthermore, in sharp curves and rapid gradient change, longitudinal and lateral dynamics of rails increase the likelihood of abrasions in concrete sleepers. This paper presents a comparative investigation using a variety of methods to evaluate creep and shrinkage effects in railway prestressed concrete sleepers. The outcome of this study will improve the material design, which is very critical to the durability of railway track components.

The Use of Deconstructed Tires as Elastic Elements in Railway Tracks.

Science.gov (United States)

Sol-Sánchez, Miguel; Moreno-Navarro, Fernando; Rubio-Gámez, Mª Carmen

2014-08-18

Elastic elements such as rail pads, under sleeper pads and under ballast mats are railway components that allow for a reduction in track deterioration and vibrations. And they are furthermore commonly used to obtain an optimal vertical stiffness of the infrastructure. However, the use of elastomeric materials can increase construction costs and the consumption of raw materials. Thus, the utilization of used tire layers offers an alternative to reuse an abundant waste reducing the cost of elastic elements. In addition, an innovator technique allows deconstructing tire layers without grinding up the material, reducing production costs at the same time that tire properties are remained. This research is focused on the study of the viability of developing elastic components from used tire layers by evaluating the influence of thickness, the resistance capacity of the elements and their behavior in a ballast box. Results indicate the ability of tire pads to manufacture elastic elements (rail pads, under sleeper pads and under ballast mats) to be used in railway tracks.

Electron attachment cross sections obtained from electron attachment spectroscopy

International Nuclear Information System (INIS)

Popp, P.; Baumbach, J.I.; Leonhardt, J.W.; Mothes, S.

1988-01-01

Electron capture detectors have a high sensitivity for substances with high thermal electron attachment cross sections. The electron attachment spectroscopy makes it possible to change the mean electron energy in such a way that the maximum for dissociative electron attachment is reached. Thus, best operation modes of the detection system as well as significant dependencies of electron attachment coefficients are available. Cross sections for electron attachment as a function of the electron energy are obtained with the knowledge of electron energy distribution functions from Boltzmann equation analysis by a special computer code. A disadvantage of this electron attachment spectroscopy is the superposition of space charge effects due to the decrease of the electron drift velocity with increasing mean electron energy. These influences are discussed. (author)

Electron beam effects in auger electron spectroscopy and scanning electron microscopy

International Nuclear Information System (INIS)

Fontaine, J.M.; Duraud, J.P.; Le Gressus, C.

1979-01-01

Electron beam effects on Si(100) and 5% Fe/Cr alloy samples have been studied by measurements of the secondary electron yield delta, determination of the surface composition by Auger electron spectroscopy and imaging with scanning electron microscopy. Variations of delta as a function of the accelerating voltage Esub(p) (0.5 -9 Torr has no effect on technological samples covered with their reaction layers; the sensitivities to the beam depend rather on the earlier mechanical, thermal and chemical treatment of the surfaces. (author)

The effect of electron-electron interaction induced dephasing on electronic transport in graphene nanoribbons

Energy Technology Data Exchange (ETDEWEB)

Kahnoj, Sina Soleimani; Touski, Shoeib Babaee [School of Electrical and Computer Engineering, University of Tehran, P.O. Box 14395-515, Tehran (Iran, Islamic Republic of); Pourfath, Mahdi, E-mail: pourfath@ut.ac.ir, E-mail: pourfath@iue.tuwien.ac.at [School of Electrical and Computer Engineering, University of Tehran, P.O. Box 14395-515, Tehran (Iran, Islamic Republic of); Institute for Microelectronics, TU Wien, Gusshausstrasse 27–29/E360, 1040 Vienna (Austria)

2014-09-08

The effect of dephasing induced by electron-electron interaction on electronic transport in graphene nanoribbons is theoretically investigated. In the presence of disorder in graphene nanoribbons, wavefunction of electrons can set up standing waves along the channel and the conductance exponentially decreases with the ribbon's length. Employing the non-equilibrium Green's function formalism along with an accurate model for describing the dephasing induced by electron-electron interaction, we show that this kind of interaction prevents localization and transport of electrons remains in the diffusive regime where the conductance is inversely proportional to the ribbon's length.

Electron Beam Generation in Tevatron Electron Lenses

International Nuclear Information System (INIS)

Kamerdzhiev, V.; Kuznetsov, G.; Shiltsev, V.; Solyak, N.; Tiunov, M.

2006-01-01

New type of high perveance electron guns with convex cathode has been developed. Three guns described in this article are built to provide transverse electron current density distributions needed for Electron Lenses for beam-beam compensation in the Tevatron collider. The current distribution can be controlled either by the gun geometry or by voltage on a special control electrode located near cathode. We present the designs of the guns and report results of beam measurements on the test bench. Because of their high current density and low transverse temperature of electrons, electron guns of this type can be used in electron cooling and beam-beam compensation devices

Electron beam generation in Tevatron electron lenses

International Nuclear Information System (INIS)

Kamerdzhiev, V.; Kuznetsov, G.; Shiltsev, V.; Solyak, N.; Tiunov, M.

2006-01-01

New type of high perveance electron guns with convex cathode has been developed. Three guns described in this article are built to provide transverse electron current density distributions needed for Electron Lenses for beam-beam compensation in the Tevatron collider. The current distribution can be controlled either by the gun geometry or by voltage on a special control electrode located near cathode. We present the designs of the guns and report results of beam measurements on the test bench. Because of their high current density and low transverse temperature of electrons, electron guns of this type can be used in electron cooling and beam-beam compensation devices

Electronic technology

International Nuclear Information System (INIS)

Kim, Jin Su

2010-07-01

This book is composed of five chapters, which introduces electronic technology about understanding of electronic, electronic component, radio, electronic application, communication technology, semiconductor on its basic, free electron and hole, intrinsic semiconductor and semiconductor element, Diode such as PN junction diode, characteristic of junction diode, rectifier circuit and smoothing circuit, transistor on structure of transistor, characteristic of transistor and common emitter circuit, electronic application about electronic equipment, communication technology and education, robot technology and high electronic technology.

Queer eller manden som ideal

DEFF Research Database (Denmark)

Sjørup, Karen

2016-01-01

Forestillingen om barnet som den i kønslig forstand renvaskede tavle er fejlagtig og selvmodsigende. I stedet bør forældre og samfund give børn ballast til at begive sig ud i livet uden for mange normative direktiver.......Forestillingen om barnet som den i kønslig forstand renvaskede tavle er fejlagtig og selvmodsigende. I stedet bør forældre og samfund give børn ballast til at begive sig ud i livet uden for mange normative direktiver....

The Electron

Energy Technology Data Exchange (ETDEWEB)

Thomson, George

1972-01-01

Electrons are elementary particles of atoms that revolve around and outside the nucleus and have a negative charge. This booklet discusses how electrons relate to electricity, some applications of electrons, electrons as waves, electrons in atoms and solids, the electron microscope, among other things.

Determination of the electron-electron collisional frequency by means of plasma electron spectroscopy

International Nuclear Information System (INIS)

Kolokolov, N.B.; Kudryavtsev, A.A.; Romanenko, V.A.

1989-01-01

Methods of controlling fast part of electron distribution function (DF) in nonlocal regime of current-free plasma are suggested and realized. Artificially created step in DF fast part has a simple link with frequencies of electron-electron and elastic electron-atom collisions that may be defined in the corresponding experiments

Electron beam-plasma interaction and electron-acoustic solitary waves in a plasma with suprathermal electrons

Science.gov (United States)

Danehkar, A.

2018-06-01

Suprathermal electrons and inertial drifting electrons, so called electron beam, are crucial to the nonlinear dynamics of electrostatic solitary waves observed in several astrophysical plasmas. In this paper, the propagation of electron-acoustic solitary waves (EAWs) is investigated in a collisionless, unmagnetized plasma consisting of cool inertial background electrons, hot suprathermal electrons (modeled by a κ-type distribution), and stationary ions. The plasma is penetrated by a cool electron beam component. A linear dispersion relation is derived to describe small-amplitude wave structures that shows a weak dependence of the phase speed on the electron beam velocity and density. A (Sagdeev-type) pseudopotential approach is employed to obtain the existence domain of large-amplitude solitary waves, and investigate how their nonlinear structures depend on the kinematic and physical properties of the electron beam and the suprathermality (described by κ) of the hot electrons. The results indicate that the electron beam can largely alter the EAWs, but can only produce negative polarity solitary waves in this model. While the electron beam co-propagates with the solitary waves, the soliton existence domain (Mach number range) becomes narrower (nearly down to nil) with increasing the beam speed and the beam-to-hot electron temperature ratio, and decreasing the beam-to-cool electron density ratio in high suprathermality (low κ). It is found that the electric potential amplitude largely declines with increasing the beam speed and the beam-to-cool electron density ratio for co-propagating solitary waves, but is slightly decreased by raising the beam-to-hot electron temperature ratio.

Cistos de Echinococcus vogeli em fígado de paca (Cuniculus paca originária do Estado do Acre, Brasil

Directory of Open Access Journals (Sweden)

Ulysses G. Meneghelli

1990-09-01

Full Text Available Quatro dos pacientes com doença hidática policística por nós observados referiam ter reconhecido doença no figado de pacas caçadas a fim de serem utilizadas como alimento; as vísceras desses animais eram, habitualmente, dadas aos cães domésticos. Todos os nossos 7 pacientes referiam contactos com cães que previamente haviam ingerido vísceras de pacas. O exame de fígado considerado doente por um dos pacientes e retirado de uma paca abatida na mesma região (Estado do Acre, Brasil de onde provieram os casos humanos mostrou a presença de cistos hidáticos. As características dos acúleos do protoscolex indicaram tratar-se da forma larval do Echinococcus vogeli. Essas observações confirmam a participação da paca no ciclo biológico do E. vogeli e a via pela qual o homem pode tomar-se o hospedeiro intermediário alternativo desse equinococo.

Embedded systems for supporting computer accessibility.

Science.gov (United States)

Mulfari, Davide; Celesti, Antonio; Fazio, Maria; Villari, Massimo; Puliafito, Antonio

2015-01-01

Nowadays, customized AT software solutions allow their users to interact with various kinds of computer systems. Such tools are generally available on personal devices (e.g., smartphones, laptops and so on) commonly used by a person with a disability. In this paper, we investigate a way of using the aforementioned AT equipments in order to access many different devices without assistive preferences. The solution takes advantage of open source hardware and its core component consists of an affordable Linux embedded system: it grabs data coming from the assistive software, which runs on the user's personal device, then, after processing, it generates native keyboard and mouse HID commands for the target computing device controlled by the end user. This process supports any operating system available on the target machine and it requires no specialized software installation; therefore the user with a disability can rely on a single assistive tool to control a wide range of computing platforms, including conventional computers and many kinds of mobile devices, which receive input commands through the USB HID protocol.

Hyperspectral Image-Based Night-Time Vehicle Light Detection Using Spectral Normalization and Distance Mapper for Intelligent Headlight Control

Directory of Open Access Journals (Sweden)

Heekang Kim

2016-07-01

Full Text Available This paper proposes a vehicle light detection method using a hyperspectral camera instead of a Charge-Coupled Device (CCD or Complementary metal-Oxide-Semiconductor (CMOS camera for adaptive car headlamp control. To apply Intelligent Headlight Control (IHC, the vehicle headlights need to be detected. Headlights are comprised from a variety of lighting sources, such as Light Emitting Diodes (LEDs, High-intensity discharge (HID, and halogen lamps. In addition, rear lamps are made of LED and halogen lamp. This paper refers to the recent research in IHC. Some problems exist in the detection of headlights, such as erroneous detection of street lights or sign lights and the reflection plate of ego-car from CCD or CMOS images. To solve these problems, this study uses hyperspectral images because they have hundreds of bands and provide more information than a CCD or CMOS camera. Recent methods to detect headlights used the Spectral Angle Mapper (SAM, Spectral Correlation Mapper (SCM, and Euclidean Distance Mapper (EDM. The experimental results highlight the feasibility of the proposed method in three types of lights (LED, HID, and halogen.

Change of the arc attachment mode and its effect on the lifetime in automotive high intensity discharge lamps

Science.gov (United States)

Alexejev, Alexander; Flesch, Peter; Mentel, Jürgen; Awakowicz, Peter

2016-10-01

In modern cars, the new generation Hg-free high intensity discharge (HID) lamps, the so called xenon lamps, take an important role. The long lifetime of these lamps is achieved by doping the tungsten electrodes with thorium. Thorium forms a dipole layer on the electrode surface, thus reducing the work function of tungsten. However, thoriating the electrodes is also an issue of trade and transport regulation, so a substitute is looked into. This work shows the influence of the arc attachment mode on the lifetime of the lamps. The mode of the arc attachment changes during the run-up phase of automotive HID lamps after a characteristic time period depending, i.e., on the filling of the lamps, which is dominated by scandium. It will be shown that this characteristic time period for the change of the attachment mode determines the long term performance of Hg-free xenon lamps. Measurements attributing the mode change to the scandium density in the filling are presented. The emitter effect of scandium will be suggested to be the reason of the mode change.

Performance of a grid connected PV system used as active filter

International Nuclear Information System (INIS)

Calleja, Hugo; Jimenez, Humberto

2004-01-01

In this paper, the performance of a grid connected photovoltaic (PV) system used as an active filter is presented. Its main feature is the capability to compensate the reactive and harmonic currents drawn by nonlinear loads while simultaneously injecting into the grid the maximum power available from the cells. The system can also operate as a stand alone active filter. The system was connected to a 1 kW PV array and tested with the loads typically found in households: small motors, personal computers and electronic ballasts. The results show that the system can correct the power factor to values close to unity for all the cases tested, thereby improving the efficiency of the electric energy supply

Max Tech and Beyond: Fluorescent Lamps

Energy Technology Data Exchange (ETDEWEB)

Scholand, Michael

2012-04-01

contains less material (i.e., glass, fill gas and phosphor), and has a higher luminance, enabling fixtures to take advantage of the smaller lamp size to improve the optics and provide more efficient overall system illuminance. In addition to offering the market a high-quality efficacious light source, another strong value proposition of fluorescent lighting is its long operating life. In today's market, one manufacturer is offering fluorescent lamps that have a rated life of 79,000 hours - which represents 18 years of service at 12 hours per day, 365 days per year. These lamps, operated using a long-life ballast specified by the manufacturer, take advantage of improvements in cathode coatings, fill gas chemistry and pressure to extend service life by a factor of four over conventional fluorescent lamps. It should be noted that this service life is also longer (approximately twice as long) as today's high-quality LED products. The fluorescent market is currently focused on the T5 and T8 lamp diameters, and it is not expected that other diameters would be introduced. Although T8 is a more optimal diameter from an efficacy perspective, the premium efficiency and optimization effort has been focused on T5 lamps because they are 40% smaller than T8, and are designed to operate at a higher temperature using high-frequency electronic ballasts. The T5 lamp offers savings in terms of materials, packaging and shipping, as well as smaller fixtures with improved optical performance. Manufacturers are actively researching improvements in four critical areas that are expected to yield additional efficacy improvements of approximately 10 to 14 percent over the next five years, ultimately achieving approximately 130 lumens per watt by 2015. The active areas of research where these improvements are anticipated include: (1) Improved phosphors which continue to be developed and patented, enabling higher efficacies as well as better color rendering and lumen maintenance; (2

Ballast Water Self Monitoring

Science.gov (United States)

2011-11-01

Hydrogen peroxide  Menadione /Vitamin K The efficacy of these processes varies by water conditions such as pH, temperature and, most significantly...Hydrocyclone power consumption, voltage and current Hydrocyclone power consumption, voltage and current Menadione /Vitamin K Menadione Chemical analysis...and treatment monitoring - Menadione /Vitamin K concentration at injection - Menadione /Vitamin K dosage and usage - Menadione /Vitamin K

Evaluation of the InnoTyper^® 21 genotyping kit in multi-ethnic populations

DEFF Research Database (Denmark)

Ristow, Peter Gustav; Barnes, Nicole; Murphy, Gina Pineda

2017-01-01

We report the findings of the evaluation of the InnoTyper® 21 genotyping kit for the use of human identification (HID) and paternity testing in South Africa. This novel forensic kit evaluates 20 retrotransposable elements (AC4027, MLS26, ALU79712, NBC216, NBC106, RG148, NBC13, AC2265, MLS09, AC11...

A transplant experiment to identify the factors controlling bacterial abundance, activity, production and community composition in a eutrophic canyon-shaped reservoir

Czech Academy of Sciences Publication Activity Database

Gasol, J. M. .; Comerma, M.; García, J. C.; Armengol, J.; Casamayor, E. O.; Kojecká, Petra; Šimek, Karel

2002-01-01

Roč. 47, č. 1 (2002), s. 62-77 ISSN 0024-3590 R&D Projects: GA ČR GA206/99/0028 Grant - others:CICYT(ES) HID99-599-CO2-01; EC(XE) MIDAS MAS3-CT97-0154 Keywords : natural planktonic bacteria * bacterioplankton diversity * assemblages Subject RIV: DA - Hydrology ; Limnology Impact factor: 3.169, year: 2002

Mass killings represented: the movies of Panh and Oppenheimer

NARCIS (Netherlands)

Kleinen, J.

2014-01-01

My movie and its title ‘The Missing Picture’ was partly inspired by my search for a photograph of an execution that a Khmer Rouge guard once told me about. The missing picture, maybe it’s the images of genocide that don’t exist. Maybe they’re lost, maybe they’re buried somewhere, maybe someone hid

Influence of 3D particle shape on the mechanical behaviour through a novel characterization method

Directory of Open Access Journals (Sweden)

Ouhbi Noura

2017-01-01

Full Text Available The sensitivity of the mechanical behaviour of railway ballast to particle shape variation is studied through Discrete Element Method (DEM numerical simulations, focusing on some basic parameters such as solid fraction, coordination number, or force distribution. We present an innovative method to characterize 3D particle shape using Proper Orthogonal Decomposition (POD of scanned ballast grains with a high accuracy. The method enables not only shape characterization but also the generation of 3D distinct and angular shapes. Algorithms are designed for face and edge recognition.

Power Quality Assessment in Real Shipboard Microgrid Systems under Unbalanced and Harmonic AC Bus Voltage

DEFF Research Database (Denmark)

Liu, Wenzhao; Tarasiuk, Tomasz; Gorniak, Mariusz

2018-01-01

were proposed and carried out in a real ship under sea-going conditions to address this problem. The ship experimental results were presented and discussed considering non-linear bow thruster load and high power ballast pump loads under unbalanced and harmonic voltage conditions. In addition......, the analysis of voltage transient dips during ballast pump starting up is presented. Further, the voltage/current distortions of working generator, bow thruster and pump loads are analyzed. The paper provides a valuable analysis for coping with PQ issues in the real ship power system....

Electronic Government and Electronic Participation

NARCIS (Netherlands)

Tambouris, E; Scholl, H.J.; Janssen, M.F.W.H.A.; Wimmer, M.A.; Tarabanis, K; Gascó, M; Klievink, A.J.; Lindgren, I; Milano, M; Panagiotopoulos, P; Pardo, T.A.; Parycek, P; Sæbø, Ø

2016-01-01

Electronic government and electronic participation continue to transform the public sector and society worldwide and are constantly being transformed themselves by emerging information and communication technologies.This book presents papers from the 14th International Federation for Information

Electronic Government and Electronic Participation

NARCIS (Netherlands)

Tambouris, E.; Scholl, H.J.; Janssen, M.F.W.H.A.; Wimmer, M.A.; Tarabanis, K.; Gascó, M.; Klievink, A.J.; Lindgren, I.; Milano, M.; Panagiotopoulos, P.; Pardo, T.A.; Parycek, P.; Sæbø, O.

2015-01-01

Electronic government and electronic participation continue to transform the public sector and society worldwide and are constantly being transformed themselves by emerging information and communication technologies. This book presents papers from the 14th International Federation for Information

Electron detector

International Nuclear Information System (INIS)

Hashimoto, H.; Mogami, A.

1975-01-01

A device for measuring electron densities at a given energy level in an electron beam or the like having strong background noise, for example, in the detection of Auger electric energy spectrums is described. An electron analyzer passes electrons at the given energy level and at the same time electrons of at least one adjacent energy level. Detecting means associated therewith produce signals indicative of the densities of the electrons at each energy level and combine these signals to produce a signal indicative of the density of the electrons of the given energy level absent background noise

Electron-electron interactions in artificial graphene

Science.gov (United States)

Rasanen, Esa

2013-03-01

Recent advances in the creation and modulation of graphenelike systems are introducing a science of ``designer Dirac materials.'' In its original definition, artificial graphene is a man-made nanostructure that consists of identical potential wells (quantum dots) arranged in an adjustable honeycomb lattice in the two-dimensional electron gas. As our ability to control the quality of artificial graphene samples improves, so grows the need for an accurate theory of its electronic properties, including the effects of electron-electron interactions. Here we determine those effects on the band structure and on the emergence of Dirac points, and discuss future investigations and challenges in this field.

[Histopathological and immunohistochemical studies on mucous cysts].

Science.gov (United States)

Kuroda, N

1989-01-01

The present study investigated the histopathology, histochemistry of mucopolysaccharides, and immunohistochemistry of oral mucous cysts. The materials were obtained from ninety cases that were histopathologically diagnosed as oral mucous cysts at the Department of Oral Pathology, Meikai University School of Dentistry. Mucopolysaccharide staining was done with PAS, alcian blue (AB, pH 2.5) and high iron diamine (HID). Immunohistochemical studies were focused on secretory component (SC), lactoferrin (Lf), alpha-amylase (Am), IgA, lysozyme (Ly), and keratin (Kr). The following results were obtained: 1. Histopathological findings. (1) Retention and/or retention-like type cysts occurred in was twenty-six cases and the extravasation type in sixty-four cases. (2) Cases showing epithelial lining of the cystic wall were only eight in number, and many cystic walls were contained granulation tissue (fifty cases). (3) As for inflammation of the cystic wall, the degree was slight, and infiltrated cells were mainly macrophages (so-called mucinophages) and lymphocytes. (4) Regarding adjoining salivary glands, acinar cells showed atrophic changes, and hypertrophy of mucous acinar cells was evident. Many ducts showed dilatation, and stromal connective tissue showed fibrosis and hyalinization. 2. Histochemical findings on mucopolysaccharides. (1) Mucous materials in cystic cavity, mucous acinar cells, and secretory materials in ductal lumens were intensely stained by PAS and AB. But stainability with AB was less than that with PAS staining. Serous acinar cells and ductal epithelium were negative to PAS and AB staining. (2) Stainability of the above with HID was less than at with PAS or AB. Cystic walls were not stained by HID. Mucous acinar cells reactive with HID were intensely stained, but the number of the positive cells was limited when compared with the numbers of PAS-and AB-positive cells. 3. Immunohistochemical findings. (1) As for mucous materials in the cystic cavity

Decal electronics for printed high performance cmos electronic systems

KAUST Repository

Hussain, Muhammad Mustafa

2017-11-23

High performance complementary metal oxide semiconductor (CMOS) electronics are critical for any full-fledged electronic system. However, state-of-the-art CMOS electronics are rigid and bulky making them unusable for flexible electronic applications. While there exist bulk material reduction methods to flex them, such thinned CMOS electronics are fragile and vulnerable to handling for high throughput manufacturing. Here, we show a fusion of a CMOS technology compatible fabrication process for flexible CMOS electronics, with inkjet and conductive cellulose based interconnects, followed by additive manufacturing (i.e. 3D printing based packaging) and finally roll-to-roll printing of packaged decal electronics (thin film transistors based circuit components and sensors) focusing on printed high performance flexible electronic systems. This work provides the most pragmatic route for packaged flexible electronic systems for wide ranging applications.

Electron-beam-induced-current and active secondary-electron voltage-contrast with aberration-corrected electron probes

Energy Technology Data Exchange (ETDEWEB)

Han, Myung-Geun, E-mail: mghan@bnl.gov [Condensed Matter Physics & Materials Science, Brookhaven National Laboratory, Upton, NY 11973 (United States); Garlow, Joseph A. [Condensed Matter Physics & Materials Science, Brookhaven National Laboratory, Upton, NY 11973 (United States); Materials Science and Engineering Department, Stony Brook University, Stony Brook, NY 11794 (United States); Marshall, Matthew S.J.; Tiano, Amanda L. [Department of Chemistry, Stony Brook University, Stony Brook, NY 11974 (United States); Wong, Stanislaus S. [Condensed Matter Physics & Materials Science, Brookhaven National Laboratory, Upton, NY 11973 (United States); Department of Chemistry, Stony Brook University, Stony Brook, NY 11974 (United States); Cheong, Sang-Wook [Department of Physics and Astronomy, Rutgers Center for Emergent Materials, Rutgers University, Piscataway, NJ 08854 (United States); Walker, Frederick J.; Ahn, Charles H. [Department of Applied Physics and Center for Research on Interface Structures and Phenomena, Yale University, New Haven, CT 06520 (United States); Department of Mechanical Engineering and Materials Science, Yale University, New Haven, CT 06520 (United States); Zhu, Yimei [Condensed Matter Physics & Materials Science, Brookhaven National Laboratory, Upton, NY 11973 (United States)

2017-05-15

Highlights: • Electron-beam-induced-current (EBIC) and active secondary-electron voltage-contrast (SE-VC) are demonstrated in STEM mode combined with in situ electrical biasing in a TEM. • Electrostatic potential maps in ferroelectric thin films, multiferroic nanowires, and single crystals obtained by off-axis electron holography were compared with EBIC and SE-VC data. • Simultaneous EBIC and active SE-VC performed with atomic resolution STEM are demonstrated. - Abstract: The ability to map out electrostatic potentials in materials is critical for the development and the design of nanoscale electronic and spintronic devices in modern industry. Electron holography has been an important tool for revealing electric and magnetic field distributions in microelectronics and magnetic-based memory devices, however, its utility is hindered by several practical constraints, such as charging artifacts and limitations in sensitivity and in field of view. In this article, we report electron-beam-induced-current (EBIC) and secondary-electron voltage-contrast (SE-VC) with an aberration-corrected electron probe in a transmission electron microscope (TEM), as complementary techniques to electron holography, to measure electric fields and surface potentials, respectively. These two techniques were applied to ferroelectric thin films, multiferroic nanowires, and single crystals. Electrostatic potential maps obtained by off-axis electron holography were compared with EBIC and SE-VC to show that these techniques can be used as a complementary approach to validate quantitative results obtained from electron holography analysis.

Electronic Commerce and Electronic Business

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

This special issue is motivated by the recent upsurge of research activity in the areas of electronic commerce and electronic business both in India and all over the world. The current ... Monte Carlo methods for pricing financial options are then.

Electron optical characteristics of a concave electrostatic electron mirror for a scanning electron microscope

International Nuclear Information System (INIS)

Hamarat, R.T.; Witzani, J.; Hoerl, E.M.

1984-08-01

Numerical computer calculations are used to explore the design characteristics of a concave electrostatic electron mirror for a mirror attachment for a conventional scanning electron microscope or an instrument designed totally as a scanning electron mirror microscope. The electron paths of a number of set-ups are calculated and drawn graphically in order to find the optimum shape and dimensions of the mirror geometry. This optimum configuration turns out to be the transition configuration between two cases of electron path deflection, towards the optical axis of the system and away from it. (Author)

Electronic processes in organic electronics bridging nanostructure, electronic states and device properties

CERN Document Server

Kudo, Kazuhiro; Nakayama, Takashi; Ueno, Nobuo

2015-01-01

The book covers a variety of studies of organic semiconductors, from fundamental electronic states to device applications, including theoretical studies. Furthermore, innovative experimental techniques, e.g., ultrahigh sensitivity photoelectron spectroscopy, photoelectron yield spectroscopy, spin-resolved scanning tunneling microscopy (STM), and a material processing method with optical-vortex and polarization-vortex lasers, are introduced. As this book is intended to serve as a textbook for a graduate level course or as reference material for researchers in organic electronics and nanoscience from electronic states, fundamental science that is necessary to understand the research is described. It does not duplicate the books already written on organic electronics, but focuses mainly on electronic properties that arise from the nature of organic semiconductors (molecular solids). The new experimental methods introduced in this book are applicable to various materials (e.g., metals, inorganic and organic mater...

Investigating the outer-bulb discharge as ignition aid for automotive-HID lamps

International Nuclear Information System (INIS)

Bergner, A; Groeger, S; Hoebing, T; Ruhrmann, C; Mentel, J; Awakowicz, P; Hechtfischer, U; Tochadse, G

2014-01-01

This work considers the ignition process of mercury-free high-intensity discharge lamps used for car headlights. These lamps have to run-up fast. This is achieved with a high xenon pressure of about 15 bar (cold) in the inner bulb. The high filling-gas pressure causes an increased ignition voltage compared with lower-pressure lamps used in general-lighting applications. In this paper the possibility is investigated to reduce the ignition voltage by optimizing a dielectric-barrier discharge (DBD) in the outer bulb working as ignition aid. A special outer bulb was built up allowing gas exchange and adjustment of the gas pressure. For diagnostic purposes different electrical and optical methods are used, namely the recording of ignition voltage, ignition current and light emission by a photo-diode signal on nanosecond time scale as well as short-time photography by a intensified charge-coupled device camera. It was found that the DBD mainly generates a potential distribution within the lamp which supports ignition by an increase in the E-field in front of the electrodes and the wall. It is shown that this effect is distinctly more effective than UV radiation potentially emitted by the DBD. (paper)

Determination of HID electrode falls in a model lamp I: Pyrometric measurements

International Nuclear Information System (INIS)

Dabringhausen, L.; Nandelstaedt, D.; Luhmann, J.; Mentel, J.

2002-01-01

To verify models describing the near-electrode regions electrodes of pure and doped tungsten for high intensity discharge lamps are investigated in a special model lamp. It can be operated with arc currents of 1 A to 10 A, DC or AC with arbitrary waveforms up to a few kHz. Argon and xenon, at pressures from 0.1 MPa to 1 MPa, are used as fill gases. A large variety of electrodes can be inserted. To perform spatially resolved measurements they are displaced reproducibly within the discharge tube during lamp operation. Spatially resolved pyrometric measurements of the electrode surface temperature in the case of DC operation are presented. From the temperature distribution the power loss of the electrodes by thermal radiation and heat conduction is determined. It increases almost linearly with the arc current at the anode and less than linear at the cathode. A relation is deduced between the cathode fall and the power fed into the cathode setting up the power balance of the cathodic current transfer zone. The resulting cathode falls show a strong dependence on the electrode diameter. Electrical measurements of separate cathode and anode falls are given in a subsequent paper. The outcomes of both methods and of modelling are compared in a third paper. (author)

HID and KID syndromes are associated with the same connexin 26 mutation.

NARCIS (Netherlands)

Geel, M. van; Steensel, M.A.M. van; Kuster, W.; Hennies, H.C.; Happle, R.H.G.; Steijlen, P.M.; Konig, A.C.

2002-01-01

BACKGROUND: Keratitis-ichthyosis-deafness (KID) syndrome is a debilitating ectodermal dysplasia that predisposes patients to develop squamous cell carcinomas in addition to leading to profound sensory deafness and erythrokeratoderma. We recently demonstrated that KID can be caused by a specific

The Use of Deconstructed Tires as Elastic Elements in Railway Tracks

Science.gov (United States)

Sol-Sánchez, Miguel; Moreno-Navarro, Fernando; Rubio-Gámez, Mª Carmen

2014-01-01

Elastic elements such as rail pads, under sleeper pads and under ballast mats are railway components that allow for a reduction in track deterioration and vibrations. And they are furthermore commonly used to obtain an optimal vertical stiffness of the infrastructure. However, the use of elastomeric materials can increase construction costs and the consumption of raw materials. Thus, the utilization of used tire layers offers an alternative to reuse an abundant waste reducing the cost of elastic elements. In addition, an innovator technique allows deconstructing tire layers without grinding up the material, reducing production costs at the same time that tire properties are remained. This research is focused on the study of the viability of developing elastic components from used tire layers by evaluating the influence of thickness, the resistance capacity of the elements and their behavior in a ballast box. Results indicate the ability of tire pads to manufacture elastic elements (rail pads, under sleeper pads and under ballast mats) to be used in railway tracks. PMID:28788168

The Use of Deconstructed Tires as Elastic Elements in Railway Tracks

Directory of Open Access Journals (Sweden)

Miguel Sol-Sánchez

2014-08-01

Full Text Available Elastic elements such as rail pads, under sleeper pads and under ballast mats are railway components that allow for a reduction in track deterioration and vibrations. And they are furthermore commonly used to obtain an optimal vertical stiffness of the infrastructure. However, the use of elastomeric materials can increase construction costs and the consumption of raw materials. Thus, the utilization of used tire layers offers an alternative to reuse an abundant waste reducing the cost of elastic elements. In addition, an innovator technique allows deconstructing tire layers without grinding up the material, reducing production costs at the same time that tire properties are remained. This research is focused on the study of the viability of developing elastic components from used tire layers by evaluating the influence of thickness, the resistance capacity of the elements and their behavior in a ballast box. Results indicate the ability of tire pads to manufacture elastic elements (rail pads, under sleeper pads and under ballast mats to be used in railway tracks.

Treatment of bilge and oily drain water of tankers and current measures against combustible oil gas discharge; Tanker no biruji yudakusui shori oyobi kanensei sekiyu gas haishutsu taiskau no genjo

Energy Technology Data Exchange (ETDEWEB)

Agatsuma, Y.

1996-07-25

This paper describes the current actual conditions on treatment of bilge discharged from engine area and oily drain water from cargo area of tankers. Clean bilge among various bilges discharged from engine area such as vapor drain, fresh water, rainwater, seawater and condensed water is directly dumped into the sea after temporary storage in a clean tank. Oily bilge is produced mainly by mixing of clean bilge and leakage oil from main engines and various auxiliaries. Oily bilge is dumped into the sea under comparative monitoring of the bilge quality with the dumping standard by oil concentration monitoring and control equipment after the primary treatment in a treatment tank and the secondary treatment in a bilge separator. Oily drain water from cargo area contains water ballast for cargo oil tanks, wash water for tanks and lines, and bilge produced in pump room. The oily drain water is dumped under a specific condition. However, water ballast for specific ballast tanks is excluded from the oily drain water. 2 figs.

Decal electronics for printed high performance cmos electronic systems

KAUST Repository

Hussain, Muhammad Mustafa; Sevilla, Galo Torres; Cordero, Marlon Diaz; Kutbee, Arwa T.

2017-01-01

High performance complementary metal oxide semiconductor (CMOS) electronics are critical for any full-fledged electronic system. However, state-of-the-art CMOS electronics are rigid and bulky making them unusable for flexible electronic applications

Precession mechanism of spin relaxation at frequent electron-electron collisions

CERN Document Server

Glazov, M M

2002-01-01

It is shown that the spin relaxation mechanism in the two-dimensional electron gas, is controlled not only through the electron pulse relaxation processes, determining the mobility, but through the electron-electron collisions as well. It is decided to use the kinetic equation, describing the electron spin mixing in the k-space, for determining the spin relaxation time tau sub s at frequent electron-electron collisions. The tau sub s time is calculated for the nondegenerated electron gas both with an account and with no account of the exchange interaction

Synthesis of CdS Sensitized TiO2 Photocatalysts: Methylene Blue Adsorption and Enhanced Photocatalytic Activities

Directory of Open Access Journals (Sweden)

A. B. Makama

2016-01-01

Full Text Available A series of CdS/TiO2 nanocomposites with different Cd to Ti molar ratio were synthesized from P25-TiO2 nanopowder using microwave-assisted hydrothermal method. The as-produced powders were characterized by XRD, electron microscopy, EDX, and UV-Vis diffuse reflectance spectroscopy. The adsorption capacity and photocatalytic activity of the samples were investigated using methylene blue as a model pollutant. Sorption tests revealed that the adsorption of MB onto the samples obeys the Freundlich-Langmuir isotherm model. The sorption capacity decreased as follows: TiO2>TCd2>TCd1>TCd3>TCd4. The results of the photocatalytic tests under high-intensity discharge (HID lamp revealed that CdS/TiO2 powders with low Cd to Ti molar ratios exhibited much higher activities than P25-TiO2. The CdS/TiO2 sample with 20% CdS/(TCd2 showed the most activity among all these samples. The results also show that the Cd to Ti molar ratio of the nanocomposite has a significant effect on the photodegradation of MB and the enhanced activities exhibited by the nanocomposites are because of the low rate of electron-hole recombination.

Extracellular phosphatases in a Mediterranean reservoir: seasonal, spatial and kinetic heterogeneity

Czech Academy of Sciences Publication Activity Database

Nedoma, Jiří; García, J.C.; Comerma, M.; Šimek, Karel; Armengol, J.

2006-01-01

Roč. 51, č. 7 (2006), s. 1264-1276 ISSN 0046-5070 R&D Projects: GA ČR(CZ) GA206/99/0028 Grant - others:SICST(ES) HID96-1374-CO2; ICST(ES) 1997SGR-122 Institutional research plan: CEZ:AV0Z60170517 Keywords : alkaline phosphatase * eutrophication * P limitation Subject RIV: DJ - Water Pollution ; Quality Impact factor: 2.502, year: 2006

Practical electronics handbook

CERN Document Server

Sinclair, Ian R

2013-01-01

Practical Electronics Handbook, Third Edition provides the frequently used and highly applicable principles of electronics and electronic circuits.The book contains relevant information in electronics. The topics discussed in the text include passive and active discrete components; linear and digital I.C.s; microprocessors and microprocessor systems; digital-analogue conversions; computer aids in electronics design; and electronic hardware components.Electronic circuit constructors, service engineers, electronic design engineers, and anyone with an interest in electronics will find the book ve

Composition quantification of electron-transparent samples by backscattered electron imaging in scanning electron microscopy

Energy Technology Data Exchange (ETDEWEB)

Müller, E., E-mail: erich.mueller@kit.edu; Gerthsen, D.

2017-02-15

The contrast of backscattered electron (BSE) images in scanning electron microscopy (SEM) depends on material parameters which can be exploited for composition quantification if some information on the material system is available. As an example, the In-concentration in thin In{sub x}Ga{sub 1−x}As layers embedded in a GaAs matrix is analyzed in this work. The spatial resolution of the technique is improved by using thin electron-transparent specimens instead of bulk samples. Although the BSEs are detected in a comparably small angular range by an annular semiconductor detector, the image intensity can be evaluated to determine the composition and local thickness of the specimen. The measured intensities are calibrated within one single image to eliminate the influence of the detection and amplification system. Quantification is performed by comparison of experimental and calculated data. Instead of using time-consuming Monte-Carlo simulations, an analytical model is applied for BSE-intensity calculations which considers single electron scattering and electron diffusion. - Highlights: • Sample thickness and composition are quantified by backscattered electron imaging. • A thin sample is used to achieve spatial resolution of few nanometers. • Calculations are carried out with a time-saving electron diffusion model. • Small differences in atomic number and density detected at low electron energies.

Quantification of the lithogenic carbon pump following a dust deposition event

Science.gov (United States)

Bressac, M.; Guieu, C.; Doxaran, D.; Bourrin, F.; Desboeufs, K.; Leblond, N.; Ridame, C.

2013-08-01

Lithogenic particles, such as desert dust, have been postulated to influence particulate organic carbon (POC) export to the deep ocean by acting as mineral ballasts. However, an accurate understanding and quantification of the POC-dust association that occurs within the upper ocean is required in order to affine the "ballast hypothesis". In the framework of the DUNE project, two artificial seedings were performed seven days apart within large mesocosms. A suite of optical and biogeochemical measurements were used to quantify surface POC export following simulated dust events within a low-nutrient low-chlorophyll ecosystem. The two successive seedings led to a 2.3-6.7 fold higher POC flux as compared to the POC flux observed in controlled mesocosms. A simple linear regression analysis revealed that the lithogenic fluxes explained more than 85% of the variance in POC fluxes. At the scale of a dust deposition event, we estimated that 42-50% of POC fluxes were strictly associated with lithogenic particles through an aggregation process. Lithogenic ballasting also likely impacted the remaining POC fraction which resulted from the fertilization effect. The observations support the "ballast hypothesis" and provide a quantitative estimation of the surface POC export abiotically triggered by dust deposition. In this work, we demonstrate that the strength of such a "lithogenic carbon pump" depends on the biogeochemical conditions of the water column at the time of deposition. Based on these observations, we suggest that this "lithogenic carbon pump" could represent a major component of the biological pump in oceanic areas subjected to intense atmospheric forcing.

Nonlinear electron-acoustic rogue waves in electron-beam plasma system with non-thermal hot electrons

Science.gov (United States)

Elwakil, S. A.; El-hanbaly, A. M.; Elgarayh, A.; El-Shewy, E. K.; Kassem, A. I.

2014-11-01

The properties of nonlinear electron-acoustic rogue waves have been investigated in an unmagnetized collisionless four-component plasma system consisting of a cold electron fluid, non-thermal hot electrons obeying a non-thermal distribution, an electron beam and stationary ions. It is found that the basic set of fluid equations is reduced to a nonlinear Schrodinger equation. The dependence of rogue wave profiles on the electron beam and energetic population parameter are discussed. The results of the present investigation may be applicable in auroral zone plasma.

Electron-cyclotron-resonant-heated electron distribution functions

International Nuclear Information System (INIS)

Matsuda, Y.; Nevins, W.M.; Cohen, R.H.

1981-01-01

Recent studies at Lawrence Livermore National Laboratory (LLNL) with a bounce-averaged Fokker-Planck code indicate that the energetic electron tail formed by electron-cyclotron resonant heating (ECRH) at the second harmonic is not Maxwellian. We present the results of our bounce-averaged Fokker-Planck code along with some simple analytic models of hot-electron distribution functions

Attainment of Electron Beam Suitable for Medium Energy Electron Cooling

International Nuclear Information System (INIS)

Seletskiy, Sergey M.; Rochester U.

2005-01-01

Electron cooling of charged particle beams is a well-established technique at electron energies of up to 300 keV. However, up to the present time the advance of electron cooling to the MeV-range energies has remained a purely theoretical possibility. The electron cooling project at Fermilab has recently demonstrated the first cooling of 8.9 GeV/c antiprotons in the Recycler ring, and therefore, has proved the validity of the idea of relativistic electron cooling. The Recycler Electron Cooler (REC) is the key component of the Tevatron Run II luminosity upgrade project. Its performance depends critically on the quality of electron beam. A stable electron beam of 4.3 MeV carrying 0.5 A of DC current is required. The beam suitable for the Recycler Electron Cooler must have an angular spread not exceeding 200 (micro)rad. The full-scale prototype of the REC was designed, built and tested at Fermilab in the Wideband laboratory to study the feasibility of attaining the high-quality electron beam. In this thesis I describe various aspects of development of the Fermilab electron cooling system, and the techniques used to obtain the electron beam suitable for the cooling process. In particular I emphasize those aspects of the work for which I was principally responsible. Chapter 1 is an introduction where I describe briefly the theory and the history of electron cooling, and derive the requirements to the quality of electron beam and requirements to the basic parameters of the Recycler Electron Cooler. Chapter 2 is devoted to the theoretical consideration of the motion of electrons in the cooling section, description of the cooling section and of the measurement of the magnetic fields. In Chapter 3 I consider different factors that increase the effective electron angle in the cooling section and suggest certain algorithms for the suppression of parasitic angles. Chapter 4 is devoted to the measurements of the energy of the electron beam. In the concluding Chapter 5 I review

Double differential distributions of electron emission in ion-atom and electron-atom collisions using an electron spectrometer

International Nuclear Information System (INIS)

Misra, Deepankar; Thulasiram, K.V.; Fernandes, W.; Kelkar, Aditya H.; Kadhane, U.; Kumar, Ajay; Singh, Yeshpal; Gulyas, L.; Tribedi, Lokesh C.

2009-01-01

We study electron emission from atoms and molecules in collisions with fast electrons and heavy ions (C 6+ ). The soft collision electrons (SE), two center electron emission (TCEE), the binary encounter (BE) events and the KLL Auger lines along with the elastically scattered peaks (in electron collisions) are studied using a hemispherical electrostatic electron analyzer. The details of the measurements along with description of the spectrometer and data acquisition system are given. The angular distributions of the low energy (few eV) electrons in soft collisions and the binary encounter electrons at keV energies are compared with quantum mechanical models based on the first Born (B1) and the continuum distorted wave-Eikonal initial state approximation (CDW-EIS).

VIRTUAL ELECTRONIC COMPONENTS OF THE ELECTRONIC EQUIPMENT

Directory of Open Access Journals (Sweden)

E. Lazarevich

2013-01-01

Full Text Available The article is present new idea of the creation, developments and improvements of the electronic equipment of complex systems by means of the virtual electronic components. The idea of the virtual electronic components is a presentation and perception of the creation and developments of the equipment on two forming: real – in the manner of standard marketed block of the intellectual property and image – in the manner of virtual component. The real component in most cases slows the development of the electronic equipment. The imaginary component is the «locomotive» of development of the electronic equipment. The Imaginary component contains the scientific has brushed against developer. The scientific has brushed against developer reveals of itself in the manner of virtual component on the modern level of the design rates of microelectronics.

Wave energy absorption by a submerged air bag connected to a rigid float

DEFF Research Database (Denmark)

Kurniawan, Adi; Chaplin, J. R.; Hann, M. R.

2017-01-01

A new wave energy device features a submerged ballasted air bag connected at the top to a rigid float. Under wave action, the bag expands and contracts, creating a reciprocating air flow through a turbine between the bag and another volume housed within the float. Laboratory measurements are gene......A new wave energy device features a submerged ballasted air bag connected at the top to a rigid float. Under wave action, the bag expands and contracts, creating a reciprocating air flow through a turbine between the bag and another volume housed within the float. Laboratory measurements...

Utilization of washery dirt and mine refuse

Energy Technology Data Exchange (ETDEWEB)

Leininger, D; Schieder, T

1975-10-02

Washery dirt and mine refuse may be used without processing as road ballast, embankments and dykes, and for filling gravel pits and subsidence areas. The properties required in road ballast are outlined. For the top portions of embankments and for frost protection layers, washery dirt must be processed to remove particles of the wrong size. Methods of heat treatment are listed, and the chemical composition of the dirt is discussed. Because of its different chemical composition, large particles are preferable to fine dirt for some applications, even if they have to be crushed. Tree planting experiments on spoilbanks are described.

A new stage of nuclear electronics-particle electronics

International Nuclear Information System (INIS)

Xi Deming

1987-01-01

The rapid development of high energy physics experiments has pushed the nuclear electronics to a new stage, i.e. the particle electronics. In this paper the background, main features and recent trends of the particle electronics are expounded

Electron transport effects in ion induced electron emission

Energy Technology Data Exchange (ETDEWEB)

Dubus, A. [Universite Libre de Bruxelles, Service de Metrologie Nucleaire (CP 165/84), 50 av. FD Roosevelt, B-1050 Brussels (Belgium)]. E-mail: adubus@ulb.ac.be; Pauly, N. [Universite Libre de Bruxelles, Service de Metrologie Nucleaire (CP 165/84), 50 av. FD Roosevelt, B-1050 Brussels (Belgium); Roesler, M. [Karl-Pokern-Str. 12, D-12587 Berlin (Germany)

2007-03-15

Ion induced electron emission (IIEE) is usually described as a three-step process, i.e. electron excitation by the incident projectile, electron transport (and multiplication) and electron escape through the potential barrier at the surface. In many cases, the first step of the process has been carefully described. The second step of the process, i.e. electron transport and multiplication, has often been treated in a very rough way, a simple decreasing exponential law being sometimes used. It is precisely the aim of the present work to show the importance of a correct description of electron transport and multiplication in a theoretical calculation of IIEE. A short overview of the electron transport models developed for IIEE is given in this work. The so-called 'Infinite medium slowing-down model' often used in recent works is evaluated by means of Monte Carlo simulations. In particular, the importance of considering correctly the semi-infinite character of the medium and the boundary condition at the vacuum-medium interface is discussed. Quantities like the electron escape depth are also briefly discussed. This evaluation has been performed in the particular case of protons (25keV

Studying electron-PAG interactions using electron-induced fluorescence

Science.gov (United States)

Narasimhan, Amrit; Grzeskowiak, Steven; Ostrander, Jonathan; Schad, Jonathon; Rebeyev, Eliran; Neisser, Mark; Ocola, Leonidas E.; Denbeaux, Gregory; Brainard, Robert L.

2016-03-01

In extreme ultraviolet (EUV) lithography, 92 eV photons are used to expose photoresists. Typical EUV resists are organic-based and chemically amplified using photoacid generators (PAGs). Upon exposure, PAGs produce acids which catalyze reactions that result in changes in solubility. In EUV lithography, photo- and secondary electrons (energies of 10- 80 eV) play a large role in PAG acid-production. Several mechanisms for electron-PAG interactions (e.g. electron trapping, and hole-initiated chemistry) have been proposed. The aim of this study is to explore another mechanism - internal excitation - in which a bound PAG electron can be excited by receiving energy from another energetic electron, causing a reaction that produces acid. This paper explores the mechanism of internal excitation through the analogous process of electron-induced fluorescence, in which an electron loses energy by transferring that energy to a molecule and that molecule emits a photon rather than decomposing. We will show and quantify electron-induced fluorescence of several fluorophores in polymer films to mimic resist materials, and use this information to refine our proposed mechanism. Relationships between the molecular structure of fluorophores and fluorescent quantum yield may aid in the development of novel PAGs for EUV lithography.

Electron-electron Thomas peak in fast transfer ionization

International Nuclear Information System (INIS)

Tolmanov, S. G.; McGuire, J. H.

2000-01-01

''Thomas process'' is a name used for a family of singular two-step processes that can lead to electron transfer. The Thomas process of the ''second kind,'' occurring in reactions with both transfer and ionization, utilizes the e-e scattering in the second step, so this Thomas process requires the dynamics of the electron-electron interaction. We calculate numerically the second order element of an S matrix and corresponding cross sections for the transfer ionization process. We find that the position and shape of the Thomas peak depend on both electron-electron and the electron-nucleus interaction. Also the direct and exchange amplitudes are equal at the peak position. We test the peaking approximation used for transfer ionization. Our results can be compared to experimental results for p + +He→H+He 2+ +e - . (c) 2000 The American Physical Society

Electron Tree

DEFF Research Database (Denmark)

Appelt, Ane L; Rønde, Heidi S

2013-01-01

The photo shows a close-up of a Lichtenberg figure – popularly called an “electron tree” – produced in a cylinder of polymethyl methacrylate (PMMA). Electron trees are created by irradiating a suitable insulating material, in this case PMMA, with an intense high energy electron beam. Upon discharge......, during dielectric breakdown in the material, the electrons generate branching chains of fractures on leaving the PMMA, producing the tree pattern seen. To be able to create electron trees with a clinical linear accelerator, one needs to access the primary electron beam used for photon treatments. We...... appropriated a linac that was being decommissioned in our department and dismantled the head to circumvent the target and ion chambers. This is one of 24 electron trees produced before we had to stop the fun and allow the rest of the accelerator to be disassembled....

Electronic Raman response in electron-doped cuprate superconductors

International Nuclear Information System (INIS)

Geng Zhihao; Feng Shiping

2012-01-01

The electronic Raman response in the electron-doped cuprate superconductors is studied based on the t-t'-J model. It is shown that although the domelike shape of the doping dependent peak energy in the B 2g symmetry is a common feature for both electron-doped and hole-doped cuprate superconductors, there are pronounced deviations from a cubic response in the B 2g channel and a linear response in the B 2g channel for the electron-doped case in the low energy limit. It is also shown that these pronounced deviations are mainly caused by a nonmonotonic d-wave gap in the electron-doped cuprate superconductors.

Spectroscopy of electron irradiated polymers in electron microscope

International Nuclear Information System (INIS)

Faraj, S.H.; Salih, S.M.

1981-01-01

The damage induced by energetic electrons in the course of irradiation of polymers in a transmission electron microscope was investigated spectroscopically. Damage on the molecular level has been detected at very low exposure doses. These effects have been induced by electron doses less than that received by the specimen when it is situated at its usual place of the specimen stage in the electron microscope by a factor of 1,000. (author)

Electron spectroscopy in the fundamental process of electron-nucleus bremsstrahlung

International Nuclear Information System (INIS)

Hillenbrand, Pierre-Michel

2013-07-01

Within the scope of this thesis the fundamental process of electron-nucleus bremsstrahlung was studied in inverse kinematics at the Experimental Storage Ring ESR at GSI. For the system U 88+ + N 2 at 90 MeV/u it was shown, that by using inverse kinematics coincidence measurements between the scattered electron and the emitted photon can be performed for the case, in which the incoming electron transfers almost all of its kinetic energy onto the emitted photon. The sensitivity to the fundamental process could be achieved by measuring triple differential cross sections as a function of the emission angle of the photon and the scattered electron as well as the energy of the scattered electron. The optics of the magnetic electron spectrometer used were thoroughly revised and optimized to the experimental requirements. Analyzing different coincidences in this collision system, it was possible to determine the contributions to the electron distribution arising from radiative electron capture to the projectile continuum, nonradiative electron capture to the projectile continuum, and electron loss to the projectile continuum. The experimental results of each of these processes were compared to theoretical calculations. The electron spectra for the radiative and the nonradiative electron capture to continuum clearly reproduce the opposite asymmetry predicted by theory. Furthermore electron spectra for collisions of U 28+ with different gases were measured.

Retroactive effects of energy-saving lamps; Netzrueckwirkungen von Energiesparlampen

Energy Technology Data Exchange (ETDEWEB)

Duerrenberger, G. [Forschungsstiftung Mobilkommunikation c/o ETH Zuerich (Switzerland); Klaus, G. [Maxwave AG, Zuerich (Switzerland)

2009-11-15

This final report for the Swiss Federal Office of Energy (SFOE) takes a look at the repercussions on the power supply network that are caused by energy-saving lamps (ESL). These effects result from the operation of the lamps' electronic ballasts which operate at high frequencies. The most noticeable network repercussions that are caused by the rapid current variations in the ESL are discussed, as are ways of considerably reducing them. As for effects on the grid, the authors state that it is not to be expected that any problematic mains feedback will result in practice, particularly not in the well-dimensioned Swiss electricity grid. The methods used in the analysis and the detailed results obtained are presented in tabular and graphical form and discussed.

An analysis of energy-efficient light fittings and lighting controls

International Nuclear Information System (INIS)

Li, Danny H.W.; Cheung, K.L.; Wong, S.L.; Lam, Tony N.T.

2010-01-01

Electric lighting is one of the major energy consuming items in many non-domestic buildings. Using appropriate energy-efficient light fittings with dimming controls and proper daylighting schemes can help reduce the electrical demand and contribute to visual comfort and green building development. This paper presents a study on the energy and lighting performances for energy-efficient fluorescent lamps associated with electronic ballasts and high frequency photoelectric dimming controls installed in a school building. Electricity expenditures and indoor illuminance levels for a workshop and a classroom employing high frequency dimming controls were analyzed. Simple prediction methods were used to illustrate the lighting savings. The findings provide the operational and performance information, which would be applicable to other spaces with similar building layouts and lighting schemes.

`Twisted' electrons

Science.gov (United States)

Larocque, Hugo; Kaminer, Ido; Grillo, Vincenzo; Leuchs, Gerd; Padgett, Miles J.; Boyd, Robert W.; Segev, Mordechai; Karimi, Ebrahim

2018-04-01

Electrons have played a significant role in the development of many fields of physics during the last century. The interest surrounding them mostly involved their wave-like features prescribed by the quantum theory. In particular, these features correctly predict the behaviour of electrons in various physical systems including atoms, molecules, solid-state materials, and even in free space. Ten years ago, new breakthroughs were made, arising from the new ability to bestow orbital angular momentum (OAM) to the wave function of electrons. This quantity, in conjunction with the electron's charge, results in an additional magnetic property. Owing to these features, OAM-carrying, or twisted, electrons can effectively interact with magnetic fields in unprecedented ways and have motivated materials scientists to find new methods for generating twisted electrons and measuring their OAM content. Here, we provide an overview of such techniques along with an introduction to the exciting dynamics of twisted electrons.

The electron

International Nuclear Information System (INIS)

Hestenes, David; Weingartshofer, Antonio

1991-01-01

The stupendous successes of the Dirac equation and quantum electro-dynamics have established the electron as the best understood of the fundamental constituents of matter. Nevertheless, physicists agree that the electron still has secrets to reveal. Moreover, powerful new theoretical and experimental tools for probing those secrets have been sharpened during the last decade. This workshop was organized to bring theorists and experimentalists together to discuss their common goal of knowing the electron. Present state and future prospects for progress toward that goal are here described. The theoretical papers encompass a wide range of views on the electron. Several argue that the 'Zitter-bewegung' is more than a mathematical peculiarity of the Dirac equation, that it may well be a real physical phenomenon and worthy of serious study, theoretically and experimentally. Besides generating the electron spin and magnetic moment, the 'Zitterbewegung' may be a vital clue to electron structure and self-interaction. Some of the papers employ a radical new formulation of the Dirac theory which reveals a hidden geo-metric structure in the theory that supports a 'Zitterbewegung' inter-pretation. For the last half century the properties of electrons have been probed primarily by scattering experiments at ever higher energies. Recently, however, two powerful new experimental techniques have emerged capable of giving alternative experimental views of the electron. First, techniques for confining single electrons for long term study have led to the most accurate measurements of the electron magnetic moment. Second, the interaction of high intensity laser fields with atoms and electrons have revealed striking new phenomena such as multiphoton ionization. refs.; figs.; tabs

Basic electronics

CERN Document Server

Holbrook, Harold D

1971-01-01

Basic Electronics is an elementary text designed for basic instruction in electricity and electronics. It gives emphasis on electronic emission and the vacuum tube and shows transistor circuits in parallel with electron tube circuits. This book also demonstrates how the transistor merely replaces the tube, with proper change of circuit constants as required. Many problems are presented at the end of each chapter. This book is comprised of 17 chapters and opens with an overview of electron theory, followed by a discussion on resistance, inductance, and capacitance, along with their effects on t

Routine health insurance data for scientific research: potential and limitations of the Agis Health Database.

Science.gov (United States)

Smeets, Hugo M; de Wit, Niek J; Hoes, Arno W

2011-04-01

Observational studies performed within routine health care databases have the advantage of their large size and, when the aim is to assess the effect of interventions, can offer a completion to randomized controlled trials with usually small samples from experimental situations. Institutional Health Insurance Databases (HIDs) are attractive for research because of their large size, their longitudinal perspective, and their practice-based information. As they are based on financial reimbursement, the information is generally reliable. The database of one of the major insurance companies in the Netherlands, the Agis Health Database (AHD), is described in detail. Whether the AHD data sets meet the specific requirements to conduct several types of clinical studies is discussed according to the classification of the four different types of clinical research; that is, diagnostic, etiologic, prognostic, and intervention research. The potential of the AHD for these various types of research is illustrated using examples of studies recently conducted in the AHD. HIDs such as the AHD offer large potential for several types of clinical research, in particular etiologic and intervention studies, but at present the lack of detailed clinical information is an important limitation. Copyright © 2011 Elsevier Inc. All rights reserved.

Electron-electron scattering and mobilities in semiconductors and quantum wells

International Nuclear Information System (INIS)

Lyo, S.K.

1986-01-01

The effect of electron-electron scattering on the mobility in semiconductors and semiconductor quantum wells is examined. A general exact formula is derived for the mobility, when the electron-electron collision rate is much faster than other scattering rates such as those by ionized impurities and phonons. In this limit, the transport relaxation rate is independent of the carrier's energy and contributions to the inverse mobility from individual scattering mechanism add up. The mobility becomes significantly reduced from its value in the absence of electron-electron scattering. When the collision rates are not necessarily dominated by electron-electron scattering, the mobility is calculated by the Kohler-Sondheimer variational method in the presence of ionized-impurity scattering and acoustic-phonon scattering in a nondegenerate two-dimensional quantum well

Modified Monte Carlo method for study of electron transport in degenerate electron gas in the presence of electron-electron interactions, application to graphene

Science.gov (United States)

Borowik, Piotr; Thobel, Jean-Luc; Adamowicz, Leszek

2017-07-01

Standard computational methods used to take account of the Pauli Exclusion Principle into Monte Carlo (MC) simulations of electron transport in semiconductors may give unphysical results in low field regime, where obtained electron distribution function takes values exceeding unity. Modified algorithms were already proposed and allow to correctly account for electron scattering on phonons or impurities. Present paper extends this approach and proposes improved simulation scheme allowing including Pauli exclusion principle for electron-electron (e-e) scattering into MC simulations. Simulations with significantly reduced computational cost recreate correct values of the electron distribution function. Proposed algorithm is applied to study transport properties of degenerate electrons in graphene with e-e interactions. This required adapting the treatment of e-e scattering in the case of linear band dispersion relation. Hence, this part of the simulation algorithm is described in details.

Attainment of Electron Beam Suitable for Medium Energy Electron Cooling

Energy Technology Data Exchange (ETDEWEB)

Seletskiy, Sergei M. [Univ. of Rochester, NY (United States)

2005-01-01

Electron cooling of charged particle beams is a well-established technique at electron energies of up to 300 keV. However, up to the present time the advance of electron cooling to the MeV-range energies has remained a purely theoretical possibility. The electron cooling project at Fermilab has recently demonstrated the ¯rst cooling of 8.9 GeV/c antiprotons in the Recycler ring, and therefore, has proved the validity of the idea of relativistic electron cool- ing. The Recycler Electron Cooler (REC) is the key component of the Teva- tron Run II luminosity upgrade project. Its performance depends critically on the quality of electron beam. A stable electron beam of 4.3 MeV car- rying 0.5 A of DC current is required. The beam suitable for the Recycler Electron Cooler must have an angular spread not exceeding 200 ¹rad. The full-scale prototype of the REC was designed, built and tested at Fermilab in the Wideband laboratory to study the feasibility of attaining the high-quality electron beam. In this thesis I describe various aspects of development of the Fermilab electron cooling system, and the techniques used to obtain the electron beam suitable for the cooling process. In particular I emphasize those aspects of the work for which I was principally responsible.

Microfluidic electronics.

Science.gov (United States)

Cheng, Shi; Wu, Zhigang

2012-08-21

Microfluidics, a field that has been well-established for several decades, has seen extensive applications in the areas of biology, chemistry, and medicine. However, it might be very hard to imagine how such soft microfluidic devices would be used in other areas, such as electronics, in which stiff, solid metals, insulators, and semiconductors have previously dominated. Very recently, things have radically changed. Taking advantage of native properties of microfluidics, advances in microfluidics-based electronics have shown great potential in numerous new appealing applications, e.g. bio-inspired devices, body-worn healthcare and medical sensing systems, and ergonomic units, in which conventional rigid, bulky electronics are facing insurmountable obstacles to fulfil the demand on comfortable user experience. Not only would the birth of microfluidic electronics contribute to both the microfluidics and electronics fields, but it may also shape the future of our daily life. Nevertheless, microfluidic electronics are still at a very early stage, and significant efforts in research and development are needed to advance this emerging field. The intention of this article is to review recent research outcomes in the field of microfluidic electronics, and address current technical challenges and issues. The outlook of future development in microfluidic electronic devices and systems, as well as new fabrication techniques, is also discussed. Moreover, the authors would like to inspire both the microfluidics and electronics communities to further exploit this newly-established field.

Electron-electron collision effects on the bremsstrahlung emission in Lorentzian plasmas

International Nuclear Information System (INIS)

Jung, Young-Dae; Kato, Daiji

2009-01-01

Electron-electron collision effects on the electron-ion bremsstrahlung process are investigated in Lorentzian plasmas. The effective electron-ion interaction potential is obtained by including the far-field terms caused by electron-electron collisions with an effective Debye length in Lorentzian plasmas. The bremsstrahlung radiation cross section is obtained as a function of the electron energy, photon energy, collision frequency, spectral index and Debye length using the Born approximation for the initial and final states of the projectile electron. It is shown that the non-Maxwellian character suppresses the bremsstrahlung radiation cross section. It is also shown that the electron-electron collision effect enhances the bremsstrahlung emission spectrum. In addition, the bremsstrahlung radiation cross section decreases with an increase in the plasma temperature.

Electron-photon and electron-electron interactions in the presence of strong electromagnetic fields

International Nuclear Information System (INIS)

Surzhykov, A.; Fritzsche, S.; Stoehlker, Th.

2010-01-01

During the last decade, photon emission from highly-charged, heavy ions has been in the focus of intense studies at the GSI accelerator and storage ring facility in Darmstadt. These studies have revealed unique information about the electron-electron and electron-photon interactions in the presence of extremely strong nuclear fields. Apart from the radiative electron capture processes, characteristic photon emission following collisional excitation of projectile ions has also attracted much interest. In this contribution, we summarize the recent theoretical studies on the production of excited ionic states and their subsequent radiative decay. We will pay special attention to the angular and polarization properties of Kα emission from helium-like ions produced by means of dielectronic recombination. The results obtained for this (resonant) capture process will be compared with the theoretical predictions for the characteristic X-rays following Coulomb excitation and radiative recombination of few-electron, heavy ions. Work is supported by Helmholtz Association and GSl under the project VH-NG--421. (author)

Sticker electronics

KAUST Repository

Hussain, Muhammad Mustafa

2017-09-08

Electronic stickers may be manufactured on flexible substrates (110, 120, 130) as layers and packaged together. The package may then have an adhesive applied to one side to provide capability for sticking the electronic devices to surfaces. The stickers can be wrappable, placed on surfaces, glued on walls or mirrors or wood or stone, and have electronics (112, 122, 132) which may or may not be ultrathin. Packaging for the electronic sticker can use polymer on cellulose manufacturing and/or three dimensional (3-D) printing. The electronic stickers may provide lighting capability, sensing capability, and/or recharging capabilities.

Electronic Commerce

Directory of Open Access Journals (Sweden)

Slavko Đerić

2016-12-01

Full Text Available Electronic commerce can be defined in different ways. Any definition helps to understand and explain that concept as better as possible.. Electronic commerce is a set of procedures and technologies that automate the tasks of financial transactions using electronic means. Also, according to some authors, electronic commerce is defined as a new concept, which is being developed and which includes process of buying and selling or exchanging products, services or information via computer networks, including the Internet. Electronic commerce is not limited just to buying and selling, but it also includes all pre-sales and after-sales ongoing activities along the supply chain. Introducing electronic commerce, using the Internet and Web services in business, realizes the way to a completely new type of economy - internet economy.

Observation of the two-electron cusp in atomic collisions. Evidence for strong electron-electron correlation

International Nuclear Information System (INIS)

Sarkadi, L.; Orban, A.

2007-01-01

Complete text of publication follows. In this report we present experimental data for a process when two electrons with velocity vectors equal to that of the projectile are emitted from collisions. By observing the two electron cusp the study of the threshold phenomenon for two-electron break-up is possible. It is a particularly interesting question whether the outgoing charged projectile can attract the two repulsing electrons so strongly that the two-electron cusp is formed. If it is so, a further question arises: Are the two electrons correlated in the final state as it is predicted by the Wannier theory? The experiments have been done at the 1 MeV VdG accelerator of ATOMKI using our TOF spectrometer. The first measurements clearly showed the formation of the two-electron cusp and signature of the electron correlation in 200 keV He 0 +He collisions. These promising results motivated us to carry out the experiment at 100 keV beam energy where the coincidence count rate is still reasonable but the energy resolution is better. For an acceptable data acquisition time we improved our data acquisition and data processing system for triple coincidence measurements. In Fig. 1a we present our measured relative fourfold differential cross section (FDCS) that shows strong electron correlation. For a comparison, in Fig. 1b we displayed the contour plot for uncorrelated electron pair emission. These latter data were synthesized artificially, generating the energies of the electron pairs from two independent double coincidence experiments. In both figures the distributions are characterized by two ridges. In Fig. 1b the ridges are perpendicular straight lines (E 1 = E 2 .13.6 eV). As a result of the correlation, the ridges in Fig. 1a are distorted in such a way that they have a joint straight-line section following the line E 1 + E 2 = 27.2 eV. This means that the electron pairs in the vicinity of the cusp maximum are emitted with a center of- mass velocity equal to that of

Electronics and Information

Institute of Scientific and Technical Information of China (English)

无

2008-01-01

@@ Previously founded as CCPITMachinery and Electronics Sub-council and CCOIC Machinery and Electronics Chamber of Corn-merce in June, 1988, CCPIT Electronics Sub-Council and CCOIC Electronics Chamber of Commerce were established in May, 1993, and then renamed as CCPIT Electronics and Information Industry Sub-council and CCOIC Electronics and Infor-mation Industry Chamber of Commerce (CCPITECC) in September 1999.

Spontaneous and stimulated emission induced by an electron, electron bunch, and electron beam in a plasma

International Nuclear Information System (INIS)

Kuzelev, M V; Rukhadze, A A

2008-01-01

Two fundamental mechanisms - the Cherenkov effect and anomalous Doppler effect - underlying the emission by an electron during its superluminal motion in medium are considered. Cherenkov emission induced by a single electron and a small electron bunch is spontaneous. In the course of spontaneous Cherenkov emission, the translational motion of an electron is slowed down and the radiation energy grows linearly with time. As the number of radiating electrons increases, Cherenkov emission becomes stimulated. Stimulated Cherenkov emission represents a resonance beam instability. This emission process is accompanied by longitudinal electron bunching in the beam or by the breaking of an electron bunch into smaller bunches, in which case the radiation energy grows exponentially with time. In terms of the longitudinal size L e of the electron bunch there is a transition region λ e 0 -1 between the spontaneous and stimulated Cherenkov effects, where λ is the average radiation wavelength, and δ 0 is the dimensionless (in units of the radiation frequency) growth rate of the Cherenkov beam instability. The range to the left of this region is dominated by spontaneous emission, whereas the range to the right of this region is dominated by stimulated emission. In contrast to the Vavilov-Cherenkov effect, the anomalous Doppler effect should always (even for a single electron) be considered as stimulated, because it can only be explained by accounting for the reverse action of the radiation field on the moving electron. During stimulated emission in conditions where anomalous Doppler effect shows itself, an electron is slowed down and spins up; in this case, the radiation energy grows exponentially with time. (reviews of topical problems)

High perveance electron gun for the electron cooling system

International Nuclear Information System (INIS)

Korotaev, Yu.; Meshkov, I.; Petrov, A.; Sidorin, A.; Smirnov, A.; Syresin, E.; Titkova, I.

2000-01-01

The cooling time in the electron cooling system is inversely proportional to the beam current. To obtain high current of the electron beam the control electrode of the gun is provided with a positive potential and an electrostatic trap for secondary electrons appears inside the electron gun. This leads to a decrease in the gun perveance. To avoid this problem, the adiabatic high perveance electron gun with the clearing control electrode is designed in JINR (J. Bosser, Y. Korotaev, I. Meshkov, E. Syresin et al., Nucl. Instr. and Meth. A 391 (1996) 103. Yu. Korotaev, I. Meshkov, A. Sidorin, A. Smirnov, E. Syresin, The generation of electron beams with perveance of 3-6 μA/V 3/2 , Proceedings of SCHEF'99). The clearing control electrode has a transverse electric field, which clears secondary electrons. Computer simulations of the potential map were made with RELAX3D computer code (C.J. Kost, F.W. Jones, RELAX3D User's Guide and References Manual)