A Novel Gas Sensor Based on MgSb2O6 Nanorods to Indicate Variations in Carbon Monoxide and Propane Concentrations

Science.gov (United States)

Guillén-Bonilla, Héctor; Flores-Martínez, Martín; Rodríguez-Betancourtt, Verónica-María; Guillen-Bonilla, Alex; Reyes-Gómez, Juan; Gildo-Ortiz, Lorenzo; de la Luz Olvera Amador, María; Santoyo-Salazar, Jaime

2016-01-01

Bystromite (MgSb2O6) nanorods were prepared using a colloidal method in the presence of ethylenediamine, after a calcination step at 800 °C in static air. From X-ray powder diffraction analyses, a trirutile-type structure with lattice parameters a = 4.64 Å and c = 9.25 Å and space group P42/mnm was identified. Using scanning electron microscopy (SEM), microrods with sizes from 0.2 to 1.6 μm were observed. Transmission electron microscopy (TEM) analyses revealed that the nanorods had a length of ~86 nm and a diameter ~23.8 nm. The gas-sensing properties of these nanostructures were tested using pellets elaborated with powders of the MgSb2O6 oxide (calcined at 800 °C) at temperatures 23, 150, 200, 250 and 300 °C. The pellets were exposed to different concentrations of carbon monoxide (CO) and propane (C3H8) at these temperatures. The results showed that the MgSb2O6 nanorods possess excellent stability and high sensitivity in these atmospheres. PMID:26840318

A Novel Gas Sensor Based on MgSb2O6 Nanorods to Indicate Variations in Carbon Monoxide and Propane Concentrations

Directory of Open Access Journals (Sweden)

Héctor Guillén-Bonilla

2016-01-01

Full Text Available Bystromite (MgSb2O6 nanorods were prepared using a colloidal method in the presence of ethylenediamine, after a calcination step at 800 °C in static air. From X-ray powder diffraction analyses, a trirutile-type structure with lattice parameters a = 4.64 Å and c = 9.25 Å and space group P42/mnm was identified. Using scanning electron microscopy (SEM, microrods with sizes from 0.2 to 1.6 μm were observed. Transmission electron microscopy (TEM analyses revealed that the nanorods had a length of ~86 nm and a diameter ~23.8 nm. The gas-sensing properties of these nanostructures were tested using pellets elaborated with powders of the MgSb2O6 oxide (calcined at 800 °C at temperatures 23, 150, 200, 250 and 300 °C. The pellets were exposed to different concentrations of carbon monoxide (CO and propane (C3H8 at these temperatures. The results showed that the MgSb2O6 nanorods possess excellent stability and high sensitivity in these atmospheres.

Fabrication, spark plasma consolidation, and thermoelectric evaluation of nanostructured CoSb₃

DEFF Research Database (Denmark)

Khan, A.; Saleemi, M.; Johnsson, M.

2014-01-01

Nanostructured powders of thermoelectric (TE) CoSb3 compounds were synthesized using a chemical alloying method. This method involved co-precipitation of oxalate precursors in aqueous solution with controlled pH, followed by thermochemical treatments including calcination and reduction to produce...... stoichiometric nanostructured CoSb3. Moreover, CoSb 3 nanoparticles were consolidated by spark plasma sintering (SPS) with a very brief processing time. Very high compaction densities (>95%) were achieved and the grain growth was almost negligible during consolidation. An iterative procedure was developed...... to minimize the grain growth while achieving sufficient densification. Grain sizes in the range of 500 nm to 1 μm, with compaction density of 95-98% were obtained. Preliminary measurements of thermal diffusivity and conductivity showed the dependence on grain size as well as on porosity. TE transport...

Zuotai and HgS differ from HgCl2 and methyl mercury in Hg accumulation and toxicity in weanling and aged rats.

Science.gov (United States)

Zhang, Bin-Bin; Li, Wen-Kai; Hou, Wei-Yu; Luo, Ya; Shi, Jing-Zhen; Li, Cen; Wei, Li-Xin; Liu, Jie

2017-09-15

Mercury sulfides are used in Ayurvedic medicines, Tibetan medicines, and Chinese medicines for thousands of years and are still used today. Cinnabar (α-HgS) and metacinnabar (β-HgS) are different from mercury chloride (HgCl 2 ) and methylmercury (MeHg) in their disposition and toxicity. Whether such scenario applies to weanling and aged animals is not known. To address this question, weanling (21d) and aged (450d) rats were orally given Zuotai (54% β-HgS, 30mg/kg), HgS (α-HgS, 30mg/kg), HgCl 2 (34.6mg/kg), or MeHg (MeHgCl, 3.2mg/kg) for 7days. Accumulation of Hg in kidney and liver, and the toxicity-sensitive gene expressions were examined. Animal body weight gain was decreased by HgCl 2 and to a lesser extent by MeHg, but unaltered after Zuotai and HgS. HgCl 2 and MeHg produced dramatic tissue Hg accumulation, increased kidney (kim-1 and Ngal) and liver (Ho-1) injury-sensitive gene expressions, but such changes are absent or mild after Zuotai and HgS. Aged rats were more susceptible than weanling rats to Hg toxicity. To examine roles of transporters in Hg accumulation, transporter gene expressions were examined. The expression of renal uptake transporters Oat1, Oct2, and Oatp4c1 and hepatic Oatp2 was decreased, while the expression of renal efflux transporter Mrp2, Mrp4 and Mdr1b was increased following HgCl 2 and MeHg, but unaffected by Zuotai and HgS. Thus, Zuotai and HgS differ from HgCl 2 and MeHg in producing tissue Hg accumulation and toxicity, and aged rats are more susceptible than weanling rats. Transporter expression could be adaptive means to reduce tissue Hg burden. Copyright © 2017 Elsevier Inc. All rights reserved.

Alternative calcination development status report

International Nuclear Information System (INIS)

Boardman, R.D.

1997-12-01

The Programmatic Spent Nuclear Fuel and (INEEL) Environmental Restoration and Waste Management Programs Environmental Impact Statement Record of Decision, dated June 1, 1995, specifies that high-level waste stored in the underground tanks at the ICPP continue to be calcined while other options to treat the waste are studied. Therefore, the High-Level Waste Program has funded a program to develop new flowsheets to increase the liquid waste processing rate. Simultaneously, a radionuclide separation process, as well as other options, are also being developed, which will be compared to the calcination treatment option. Two alternatives emerged as viable candidates; (1) elevated temperature calcination (also referred to as high temperature calcination), and (2) sugar-additive calcination. Both alternatives were determined to be viable through testing performed in a lab-scale calcination mockup. Subsequently, 10-cm Calciner Pilot Plant scoping tests were successfully completed for both flowsheets. The results were compared to the standard 500 C, high-ANN flow sheet (baseline flowsheet). The product and effluent streams were characterized to help elucidate the process chemistry and to investigate potential environmental permitting issues. Several supplementary tests were conducted to gain a better understanding of fine-particles generation, calcine hydration, scrub foaming, feed makeup procedures, sugar/organic elimination, and safety-related issues. Many of the experiments are only considered to be scoping tests, and follow-up experiments will be required to establish a more definitive understanding of the flowsheets. However, the combined results support the general conclusion that flowsheet improvements for the NWCF are technically viable

Flash calcination of kaolinite rich clay and impact of process conditions on the quality of the calcines

DEFF Research Database (Denmark)

Gebremariam, Abraham Teklay; Yin, Chungen; Rosendahl, Lasse

2016-01-01

Use of properly calcined kaolinite rich clay (i.e., metakaolin) to offset part of CO2-intensive clinkers not only reduces CO2 footprint from cement industry but also improves the performance of concrete. However, calcination under inappropriately high temperatures or long retention times may...... suspension calciner. The model is validated by the experimental data (e.g., the degree of dehydroxylation and the density of the calcines). Based on the model, the impacts of process conditions and feed properties on the quality of the calcination products are thoroughly examined....

Yield of 117Sb, 118mSb, 120mSb, 122Sb, 124Sb in reactions Sn (p, xn)

International Nuclear Information System (INIS)

Dmitriev, P.P.; Konstantinov, I.O.

1993-01-01

Yield of 117 Sb, 118m Sb, 120m Sb, 122 Sb, 124 Sb from thick target depending on proton energy is measured. The maximum proton energy is 21.7±0.2 MeV. Antimony isotopes yield in separate reactions when irradiating of tin isotopes with 100% enrichment is determined using the method published earlier. The methods for production of 117 Sb, 118m Sb, 120m Sb, 122 Sb, 124 Sb with high radioisotope purity are shown. 13 refs., 1 fig., 3 tabs

Uranium dioxide calcining apparatus

International Nuclear Information System (INIS)

Cole, E.A.; Peterson, R.S.

1978-01-01

This invention relates to an improved continuous calcining apparatus for consistently and controllably producing from calcinable reactive solid compounds of uranium, such as ammonium diuranate, uranium dioxide (UO 2 ) having an oxygen to uranium ratio of less than 2.2. The apparatus comprises means at the outlet end of a calciner kiln for receiving hot UO 2 , means for cooling the UO 2 to a temperature of below 100 deg C and conveying the cooled UO 2 to storage or to subsequent UO 2 processing apparatus where it finally comes into contact with air, the means for receiving cooling and conveying being sealed to the outlet end of the calciner and being maintained full of UO 2 and so operable as to exclude atmospheric oxygen from coming into contact with any UO 2 which is at elevated temperatures where it would readily oxidize, without the use of extra hydrogen gas in said means. (author)

Properties of radioactive calcine retrieved from the second calcined solids storage facility at ICPP

International Nuclear Information System (INIS)

Staples, B.A.; Pomiak, G.S.; Wade, E.L.

1979-03-01

The chemical and physical properties of radioactive alumina and zirconia calcine samples retrieved from the storage bins at ICPP were measured. Chemical properties measured include chemical composition, crystalline structure, and radiochemical composition. The physical properties measured and reported include density, size distribution, relative attrition, solubility in 8 M HNO 3 , thermal stability, and flow characteristics. The chemical and physical properties of the retrieved calcine after the 10 to 12 years of storage are very similar to freshly prepared simulated calcine

Remotely replaceable fuel and feed nozzles for the new waste calcining facility calciner vessel

International Nuclear Information System (INIS)

Fletcher, R.D.; Carter, J.A.; May, K.W.

1978-01-01

The development and testing of remotely replaceable fuel and feed nozzles for calcination of liquid radioactive wastes in the calciner vessel of the New Waste Calcining Facility being built at the Idaho National Engineering Laboratory is described. A complete fuel nozzle assembly was fabricated and tested at the Remote Maintenance Development Facility to evolve design refinements, identify required support equipment, and develop handling techniques. The design also provided for remote replacement of the nozzle support carriage and adjacent feed and fuel pipe loops using two pairs of master-slave manipulators

Calcined solids storage facility closure study

International Nuclear Information System (INIS)

Dahlmeir, M.M.; Tuott, L.C.; Spaulding, B.C.

1998-02-01

The disposal of radioactive wastes now stored at the Idaho National Engineering and Environmental Laboratory is currently mandated under a open-quotes Settlement Agreementclose quotes (or open-quotes Batt Agreementclose quotes) between the Department of Energy and the State of Idaho. Under this agreement, all high-level waste must be treated as necessary to meet the disposal criteria and disposed of or made road ready to ship from the INEEL by 2035. In order to comply with this agreement, all calcined waste produced in the New Waste Calcining Facility and stored in the Calcined Solids Facility must be treated and disposed of by 2035. Several treatment options for the calcined waste have been studied in support of the High-Level Waste Environmental Impact Statement. Two treatment methods studied, referred to as the TRU Waste Separations Options, involve the separation of the high-level waste (calcine) into TRU waste and low-level waste (Class A or Class C). Following treatment, the TRU waste would be sent to the Waste Isolation Pilot Plant (WIPP) for final storage. It has been proposed that the low-level waste be disposed of in the Tank Farm Facility and/or the Calcined Solids Storage Facility following Resource Conservation and Recovery Act closure. In order to use the seven Bin Sets making up the Calcined Solids Storage Facility as a low-level waste landfill, the facility must first be closed to Resource Conservation and Recovery Act (RCRA) standards. This study identifies and discusses two basic methods available to close the Calcined Solids Storage Facility under the RCRA - Risk-Based Clean Closure and Closure to Landfill Standards. In addition to the closure methods, the regulatory requirements and issues associated with turning the Calcined Solids Storage Facility into an NRC low-level waste landfill or filling the bin voids with clean grout are discussed

Calcined solids storage facility closure study

Energy Technology Data Exchange (ETDEWEB)

Dahlmeir, M.M.; Tuott, L.C.; Spaulding, B.C. [and others

1998-02-01

The disposal of radioactive wastes now stored at the Idaho National Engineering and Environmental Laboratory is currently mandated under a {open_quotes}Settlement Agreement{close_quotes} (or {open_quotes}Batt Agreement{close_quotes}) between the Department of Energy and the State of Idaho. Under this agreement, all high-level waste must be treated as necessary to meet the disposal criteria and disposed of or made road ready to ship from the INEEL by 2035. In order to comply with this agreement, all calcined waste produced in the New Waste Calcining Facility and stored in the Calcined Solids Facility must be treated and disposed of by 2035. Several treatment options for the calcined waste have been studied in support of the High-Level Waste Environmental Impact Statement. Two treatment methods studied, referred to as the TRU Waste Separations Options, involve the separation of the high-level waste (calcine) into TRU waste and low-level waste (Class A or Class C). Following treatment, the TRU waste would be sent to the Waste Isolation Pilot Plant (WIPP) for final storage. It has been proposed that the low-level waste be disposed of in the Tank Farm Facility and/or the Calcined Solids Storage Facility following Resource Conservation and Recovery Act closure. In order to use the seven Bin Sets making up the Calcined Solids Storage Facility as a low-level waste landfill, the facility must first be closed to Resource Conservation and Recovery Act (RCRA) standards. This study identifies and discusses two basic methods available to close the Calcined Solids Storage Facility under the RCRA - Risk-Based Clean Closure and Closure to Landfill Standards. In addition to the closure methods, the regulatory requirements and issues associated with turning the Calcined Solids Storage Facility into an NRC low-level waste landfill or filling the bin voids with clean grout are discussed.

[Infrared spectral analysis for calcined borax].

Science.gov (United States)

Zhao, Cui; Ren, Li-Li; Wang, Dong; Zhou, Ping; Zhang, Qian; Wang, Bo-Tao

2011-08-01

To valuate the quality of calcined borax which is sold in the market, 18 samples of calcined borax were studied using the Fourier transform infrared, and samples with different water content were selected and analyzed. Then, the results of analysis were used to evaluate the quality of calcined borax. Results show that the infrared spectra of calcined borax include OH vibration, BO3(-3) vibration and BO4(5-) vibration absorption bands. The position and width of OH vibration absorption band depend on the level of water content, and the more the water content, the wider the absorption band. The number of BO3(3-) vibration and BO4(5-) vibration bands also depend on the level of water content, and the more the water content, and the stronger the hydrogen bond and the lower the symmetry of B atoms, the more the number of infrared absorption peaks. It was concluded that because the quality of calcined borax has direct correlation with water content, the infrared spectroscopy is an express and objective approach to quality analysis and evaluation of calcined borax.

Synthesis and Characterization of Hexadecylamine Capped ZnS, CdS, and HgS Nanoparticles Using Heteroleptic Single Molecular Precursors

Directory of Open Access Journals (Sweden)

Peter A. Ajibade

2014-01-01

Full Text Available Zn(II, Cd(II, and Hg(II complexes of tetramethyl thiuram disulfides and 1-ethoxylcarbonyl-1-ethylenecarbonyl-2-dithiolate were synthesized and characterized by elemental analysis, FTIR, and 1H- and 13C-NMR spectroscopy. The complexes were thermolysed in hexadecylamine as single molecule precursors to prepare HDA capped ZnS, CdS, and HgS nanoparticles. The optical and structural properties of the nanoparticles are reported. ZnS nanoparticles existed in the hexagonal phase with particle sizes of 8–15 nm; the CdS nanoparticles in the cubic phase have particle sizes in the range 4–7 nm and the HgS nanoparticles indexed to face-centered cubic phase have an average particle size of 7–12 nm.

Experimental results: Pilot plant calcine dissolution and liquid feed stability

International Nuclear Information System (INIS)

Herbst, R.S.; Fryer, D.S.; Brewer, K.N.; Johnson, C.K.; Todd, T.A.

1995-02-01

The dissolution of simulated Idaho Chemical Processing Plant pilot plant calcines, containing none of the radioactive actinides, lanthanides or fission products, was examined to evaluate the solubility of calcine matrix materials in acidic media. This study was a necessary precursor to dissolution and optimization experiments with actual radionuclide-containing calcines. The importance of temperature, nitric acid concentration, ratio of acid volume to calcine mass, and time on the amount, as a weight percentage of calcine dissolved, was evaluated. These parameters were studied for several representative pilot plant calcine types: (1) Run No. 74 Zirconia calcine; (2) Run No. 17 Zirconia/Sodium calcine; (3) Run No. 64 Zirconia/Sodium calcine; (3) Run No. 1027 Alumina calcine; and (4) Run No. 20 Alumina/Zirconia/Sodium calcine. Statistically designed experiments with the different pilot plant calcines indicated the effect of the studied process variables on the amount of calcine dissolved decreases in the order: Acid/Calcine Ratio > Temperature > HNO 3 Concentration > Dissolution Time. The following conditions are suitable to achieve greater than 90 wt. % dissolution of most Zr, Al, or Na blend calcines: (1) Maximum nitric acid concentration of 5M; (2) Minimum acid/calcine ratio of 10 mL acid/1 gram calcine; (3) Minimum dissolution temperature of 90 degrees C; and (4) Minimum dissolution time of 30 minutes. The formation of calcium sulphate (CaSO 4 ) precipitates was observed in certain dissolved calcine solutions during the dissolution experiments. Consequently, a study was initiated to evaluate if and under what conditions the resulting dissolved calcine solutions would be unstable with regards to precipitate formation. The results indicate that precipitate formation in the calcine solutions prepared under the above proposed dissolution conditions are not anticipated

Dissolution studies with pilot plant and actual INTEC calcines

International Nuclear Information System (INIS)

Herbst, R.S.; Garn, T.G.

1999-01-01

The dissolution of Idaho Nuclear Technology and Engineering Center (INTEC) pilot plant calcines was examined to determine solubility of calcine matrix components in acidic media. Two representatives pilot plant calcine types were studied: Zirconia calcine and Zirconia/Sodium calcine. Dissolution of these calcines was evaluated using lower initial concentrations of nitric acid than used in previous tests to decrease the [H+] concentration in the final solutions. Lower [H+] concentrations contribute to more favorable TRUEX/SREX solvent extraction flowsheet performance. Dissolution and analytical results were also obtained for radioactive calcines produced using high sodium feeds blended with non-radioactive Al(NO 3 ) 3 solutions to dilute the sodium concentration and prevent bed agglomeration during the calcination process. Dissolution tests indicated >95 wt.% of the initial calcine mass can be dissolved using the baseline dissolution procedure, with the exception that higher initial nitric acid concentrations are required. The higher initial acid concentration is required for stoichiometric dissolution of the oxides, primarily aluminum oxide. Statistically designed experiments using pilot plant calcine were performed to determine the effect of mixing rate on dissolution efficiency. Mixing rate was determined to provide minimal effects on wt.% dissolution. The acid/calcine ratio and temperature were the predominate variables affecting the wt.% dissolution, a result consistent with previous studies using other similar types of pilot plant calcines

XANES analysis of dried and calcined bones

International Nuclear Information System (INIS)

Rajendran, Jayapradhi; Gialanella, Stefano; Aswath, Pranesh B.

2013-01-01

The structure of dried and calcined bones from chicken, bovine, deer, pig, sheep and chamois was examined using X-ray Absorption Near Edge Structure (XANES) spectroscopy. The oxygen K-edge absorption edge indicates that the surface of dried bone has a larger proportion of carbonate than the interior that is made up of phosphates. The phosphorus L and K edge clearly indicate that pyrophosphates, α-tricalcium phosphate (α-TCP) and hydrogen phosphates of Ca do not exist in either the dried bone or calcined bone and phosphorus exists as either β-tricalcium phosphate (β-TCP) or hydroxyapatite, both in the dried and calcined conditions. The Ca K-edge analysis indicates that β-TCP is the likely form of phosphate in both the dried and calcined conditions. - Highlights: • For the first time bones of five different species of vertebrates have been compared in both the dried and calcined states. • O, P and Ca edges detail the local coordination of these atoms in dried and calcined bone. • O K-edge shows that the surface of bone has more CO 3 while the interior has more PO 4 . • P and Ca edges eliminate the presence of pyrophosphates and confirmed the presence of HA and β-TCP. • The stability of these phosphates on calcination has been examined using XANES

XANES analysis of dried and calcined bones

Energy Technology Data Exchange (ETDEWEB)

Rajendran, Jayapradhi [Materials Science and Engineering Department, University of Texas at Arlington (United States); Gialanella, Stefano [Materials Science and Industrial Technology Department, University of Trento (Italy); Aswath, Pranesh B., E-mail: aswath@uta.edu [Materials Science and Engineering Department, University of Texas at Arlington (United States)

2013-10-15

The structure of dried and calcined bones from chicken, bovine, deer, pig, sheep and chamois was examined using X-ray Absorption Near Edge Structure (XANES) spectroscopy. The oxygen K-edge absorption edge indicates that the surface of dried bone has a larger proportion of carbonate than the interior that is made up of phosphates. The phosphorus L and K edge clearly indicate that pyrophosphates, α-tricalcium phosphate (α-TCP) and hydrogen phosphates of Ca do not exist in either the dried bone or calcined bone and phosphorus exists as either β-tricalcium phosphate (β-TCP) or hydroxyapatite, both in the dried and calcined conditions. The Ca K-edge analysis indicates that β-TCP is the likely form of phosphate in both the dried and calcined conditions. - Highlights: • For the first time bones of five different species of vertebrates have been compared in both the dried and calcined states. • O, P and Ca edges detail the local coordination of these atoms in dried and calcined bone. • O K-edge shows that the surface of bone has more CO{sub 3} while the interior has more PO{sub 4}. • P and Ca edges eliminate the presence of pyrophosphates and confirmed the presence of HA and β-TCP. • The stability of these phosphates on calcination has been examined using XANES.

Bin Set 1 Calcine Retrieval Feasibility Study

International Nuclear Information System (INIS)

Adams, R.D.; Berry, S.M.; Galloway, K.J.; Langenwalter, T.A.; Lopez, D.A.; Noakes, C.M.; Peterson, H.K.; Pope, M.I.; Turk, R.J.

1999-01-01

At the Department of Energy's Idaho Nuclear Technology and Engineering Center, as an interim waste management measure, both mixed high-level liquid waste and sodium bearing waste have been solidified by a calculation process and are stored in the Calcine Solids Storage Facilities. This calcined product will eventually be treated to allow final disposal in a national geologic repository. The Calcine Solids Storage Facilities comprise seven ''bit sets.'' Bin Set 1, the first to be constructed, was completed in 1959, and has been in service since 1963. It is the only bin set that does not meet current safe-shutdown earthquake seismic criteria. In addition, it is the only bin set that lacks built-in features to aid in calcine retrieval. One option to alleviate the seismic compliance issue is to transport the calcine from Bin Set 1 to another bin set which has the required capacity and which is seismically qualified. This report studies the feasibility of retrieving the calcine from Bi n Set 1 and transporting it into Bin Set 6 which is located approximately 650 feet away. Because Bin Set 1 was not designed for calcine retrieval, and because of the high radiation levels and potential contamination spread from the calcined material, this is a challenging engineering task. This report presents preconceptual design studies for remotely-operated, low-density, pneumatic vacuum retrieval and transport systems and equipment that are based on past work performed by the Raytheon Engineers and Constructors architectural engineering firm. The designs presented are considered feasible; however, future development work will be needed in several areas during the subsequent conceptual design phase

Bin Set 1 Calcine Retrieval Feasibility Study

Energy Technology Data Exchange (ETDEWEB)

R. D. Adams; S. M. Berry; K. J. Galloway; T. A. Langenwalter; D. A. Lopez; C. M. Noakes; H. K. Peterson; M. I. Pope; R. J. Turk

1999-10-01

At the Department of Energy's Idaho Nuclear Technology and Engineering Center, as an interim waste management measure, both mixed high-level liquid waste and sodium bearing waste have been solidified by a calculation process and are stored in the Calcine Solids Storage Facilities. This calcined product will eventually be treated to allow final disposal in a national geologic repository. The Calcine Solids Storage Facilities comprise seven ''bit sets.'' Bin Set 1, the first to be constructed, was completed in 1959, and has been in service since 1963. It is the only bin set that does not meet current safe-shutdown earthquake seismic criteria. In addition, it is the only bin set that lacks built-in features to aid in calcine retrieval. One option to alleviate the seismic compliance issue is to transport the calcine from Bin Set 1 to another bin set which has the required capacity and which is seismically qualified. This report studies the feasibility of retrieving the calcine from Bi n Set 1 and transporting it into Bin Set 6 which is located approximately 650 feet away. Because Bin Set 1 was not designed for calcine retrieval, and because of the high radiation levels and potential contamination spread from the calcined material, this is a challenging engineering task. This report presents preconceptual design studies for remotely-operated, low-density, pneumatic vacuum retrieval and transport systems and equipment that are based on past work performed by the Raytheon Engineers and Constructors architectural engineering firm. The designs presented are considered feasible; however, future development work will be needed in several areas during the subsequent conceptual design phase.

Calcination/dissolution testing for Hanford Site tank wastes

International Nuclear Information System (INIS)

Colby, S.A.; Delegard, C.H.; McLaughlin, D.F.; Danielson, M.J.

1994-07-01

Thermal treatment by calcination offers several benefits for the treatment of Hanford Site tank wastes, including the destruction of organics and ferrocyanides and an hydroxide fusion that permits the bulk of the mostly soluble nonradioactive constituents to be easily separated from the insoluble transuranic residue. Critical design parameters were tested, including: (1) calciner equipment design, (2) hydroxide fusion chemistry, and (3) equipment corrosion. A 2 gal/minute pilot plant processed a simulated Tank 101-SY waste and produced a free flowing 700 C molten calcine with an average calciner retention time of 20 minutes and >95% organic, nitrate, and nitrite destruction. Laboratory experiments using actual radioactive tank waste and the simulated waste pilot experiments indicate that 98 wt% of the calcine produced is soluble in water, leaving an insoluble transuranic fraction. All of the Hanford Site tank wastes can benefit from calcination/dissolution processing, contingent upon blending various tank waste types to ensure a target of 70 wt% sodium hydroxide/nitrate/nitrite fluxing agent. Finally, corrosion testing indicates that a jacketed nickel liner cooled to below 400 C would corrode <2 mil/year (0.05 mm/year) from molten calcine attack

1st International Conference on Calcined Clays for Sustainable Concrete

CERN Document Server

Favier, Aurélie

2015-01-01

This volume focuses on research and practical issues linked to Calcined Clays for Sustainable Concrete. The main subjects are geology of clays, hydration and performance of blended systems with calcined clays, alkali activated binders, economic and environmental impacts of the use of calcined clays in cement based materials. Topics addressed in this book include the influence of processing on reactivity of calcined clays, influence of clay mineralogy on reactivity, geology of clay deposits, Portland-calcined clay systems, hydration, durability, performance, Portland-calcined clay-limestone systems, hydration, durability, performance, calcined clay-alkali systems, life cycle analysis, economics and environmental impact of use of calcined clays in cement and concrete, and field applications. This book compiles the different contributions of the 1st International Conference on Calcined Clays for Sustainable Concrete, which took place in Lausanne, Switzerland, June, 23-25, 2015.The papers present the latest  res...

Uranium dioxide calcining apparatus and method

International Nuclear Information System (INIS)

Cole, E.A.; Peterson, R.S.

1978-01-01

This invention relates to an improved continuous calcining apparatus for consistently and controllably producing from calcinable reactive solid compounds of uranium, such as ammonium diuranate, uranium dioxide (UO 2 ) having an oxygen to uranium ratio of less than 2.2. The apparatus comprises means at the outlet end of a calciner kiln for receiving hot UO 2 , means for cooling the UO 2 to a temperature of below 100 0 C and conveying the cooled UO 2 to storage or to subsequent UO 2 processing apparatus where it finally comes into contact with air, the means for receiving, cooling and conveying being sealed to the outlet end of the calciner and being maintained full of UO 2 and so operable as to exclude atmospheric oxygen from coming into contact with any UO 2 which is at elevated temperatures where it would readily oxidize, without the use of extra hydrogen gas in said means

Calcination of the cerium concentrate to be cerium oxide

International Nuclear Information System (INIS)

Suyanti; MV Purwani

2016-01-01

Calcination of the cerium concentrate to be cerium oxide has done. The cerium concentrate were obtained from the Ce making process wear KBrO_3 and without using KBrO_3. The calcination were done with a variation of time 1, 2, 3 and 4 hours with the temperature variations of 700, 800 and 900°C. The easiest calcination of Ce concentrates to be CeO_2 containing majority of Ce(OH)_4 and contains least impurities as Th(OH)_4, (NH_4)_2Y(NO_3), H_4N_5O_1_2La, H_1_2N_3NdO_1_5 and N_3O_9Sm. On the calcination of Ce concentrates process results without using KBrO_3 1, the calcination temperature 900°C was obtained CeO_2 content of 73.53% for calcination time of 4 hours, has little difference when compared with the predictions and calculation result of complete calcination was equal 73.84%. (author)

Calcination under negative atmosphere for SYNROC preparation

International Nuclear Information System (INIS)

Ambashta, R.D.; Wattal, P.K.; Govindankutty, K.V.

2006-01-01

SYNROC-C is a ceramic waste formulation designed to immobilise reprocessing waste from fast breeder reactor. This formulation is capable of incorporating noble metals, other fission products, corrosion products and activation products in its multiphase assemblage. Calcination is an important step of SYNROC preparation for decomposition of nitrates of the radioactive waste and conversion to oxide precursors. This paper presents a comparison between properties of calcine prepared under different calcination procedures to obtain product suitable for compaction

Calcined Waste Storage at the Idaho Nuclear Technology and Engineering Center

Energy Technology Data Exchange (ETDEWEB)

Staiger, M. Daniel, Swenson, Michael C.

2011-09-01

This comprehensive report provides definitive volume, mass, and composition (chemical and radioactivity) of calcined waste stored at the Idaho Nuclear Technology and Engineering Center. Calcine composition data are required for regulatory compliance (such as permitting and waste disposal), future treatment of the caline, and shipping the calcine to an off-Site-facility (such as a geologic repository). This report also contains a description of the calcine storage bins. The Calcined Solids Storage Facilities (CSSFs) were designed by different architectural engineering firms and built at different times. Each CSSF has a unique design, reflecting varying design criteria and lessons learned from historical CSSF operation. The varying CSSF design will affect future calcine retrieval processes and equipment. Revision 4 of this report presents refinements and enhancements of calculations concerning the composition, volume, mass, chemical content, and radioactivity of calcined waste produced and stored within the CSSFs. The historical calcine samples are insufficient in number and scope of analysis to fully characterize the entire inventory of calcine in the CSSFs. Sample data exist for all the liquid wastes that were calcined. This report provides calcine composition data based on liquid waste sample analyses, volume of liquid waste calcined, calciner operating data, and CSSF operating data using several large Microsoft Excel (Microsoft 2003) databases and spreadsheets that are collectively called the Historical Processing Model. The calcine composition determined by this method compares favorably with historical calcine sample data.

Calcined Waste Storage at the Idaho Nuclear Technology and Engineering Center

International Nuclear Information System (INIS)

Staiger, M. Daniel; Swenson, Michael C.

2011-01-01

This comprehensive report provides definitive volume, mass, and composition (chemical and radioactivity) of calcined waste stored at the Idaho Nuclear Technology and Engineering Center. Calcine composition data are required for regulatory compliance (such as permitting and waste disposal), future treatment of the caline, and shipping the calcine to an off-Site-facility (such as a geologic repository). This report also contains a description of the calcine storage bins. The Calcined Solids Storage Facilities (CSSFs) were designed by different architectural engineering firms and built at different times. Each CSSF has a unique design, reflecting varying design criteria and lessons learned from historical CSSF operation. The varying CSSF design will affect future calcine retrieval processes and equipment. Revision 4 of this report presents refinements and enhancements of calculations concerning the composition, volume, mass, chemical content, and radioactivity of calcined waste produced and stored within the CSSFs. The historical calcine samples are insufficient in number and scope of analysis to fully characterize the entire inventory of calcine in the CSSFs. Sample data exist for all the liquid wastes that were calcined. This report provides calcine composition data based on liquid waste sample analyses, volume of liquid waste calcined, calciner operating data, and CSSF operating data using several large Microsoft Excel (Microsoft 2003) databases and spreadsheets that are collectively called the Historical Processing Model. The calcine composition determined by this method compares favorably with historical calcine sample data.

Activity and structure of calcined coal gangue

Energy Technology Data Exchange (ETDEWEB)

Gong Chenchen; Li Dongxu; Wang Xiaojun; Li Zongjin [Nanjing University of Technology, Nanjing (China). College of Materials Science and Engineering

2007-12-15

Coal gangue was activated by means of calcination in seven temperature ranges. Systematic research was made about activation mechanism and structural evolution. The glycerin-ethanol method, SEM, MIP and XRD were used to determine the variation of structure and activation of coal gangue during calcination. The experimental results show that because of heat treatment in the range of calcination temperatures, mineral composition and microstructure of coal gangue are changed. In addition, its activity is improved. The amount of lime absorbed by the sample calcined at 700{sup o}C is 2-4 times that by uncalcined coal gangue in the course of hydration. When NaOH is added to coal gangue-lime system, the hydration reaction rate of the system is increased and the microstructure of hydrating samples of coal gangue is improved.

Sensitivity of Mesoporous CoSb2O6 Nanoparticles to Gaseous CO and C3H8 at Low Temperatures

Directory of Open Access Journals (Sweden)

Héctor Guillén-Bonilla

2015-01-01

Full Text Available Mesoporous CoSb2O6 nanoparticles, synthesized through a nonaqueous method (using cobalt nitrate, antimony trichloride, ethylenediamine, and ethanol as a solvent, were tested to establish their sensitivity to CO and C3H8 atmospheres at relatively low temperatures. The precursor material was dried at 200°C and calcined at 600°C. X-ray diffraction and scanning electron microscopy were employed to verify the existence of crystal phases (P42/mnm and the morphology of this trirutile-type CoSb2O6 oxide. Pyramidal and cubic shaped crystals (average size: 41.1 nm, embedded in the material’s surface, were identified. Mesopores (average size: 6.5 nm on the nanoparticles’ surface were observed by means of transmission electron microscopy. The best sensitivity of the CoSb2O6 in a CO atmosphere was at the relatively low temperatures of 250 and 350°C, whereas, in a C3H8 atmosphere, the sensitivity increased uniformly with temperature. These results encourage using the CoSb2O6 nanoparticles as gas sensors.

Fluidized-bed calcination of simulated commercial high-level radioactive wastes

International Nuclear Information System (INIS)

Freeby, W.A.

1975-11-01

Work is in progress at the Idaho Chemical Processing Plant to verify process flowsheets for converting simulated commercial high-level liquid wastes to granular solids using the fluidized-bed calcination process. Primary emphasis in the series of runs reported was to define flowsheets for calcining simulated Allied-General Nuclear Services (AGNS) waste and to evaluate product properties significant to calcination, solids storage, or post treatment. Pilot-plant studies using simulated high-level acid wastes representative of those to be produced by Nuclear Fuel Services, Inc. (NFS) are also included. Combined AGNS high-level and intermediate-level waste (0.26 M Na in blend) was successfully calcined when powdered iron was added (to result in a Na/Fe mole ratio of 1.0) to the feed to prevent particle agglomeration due to sodium nitrate. Long-term runs (approximately 100 hours) showed that calcination of the combined waste is practical. Concentrated AGNS waste containing sodium at concentrations less than 0.2 M were calcined successfully; concentrated waste containing 1.13 M Na calcined successfully when powdered iron was added to the feed to suppress sodium nitrate formation. Calcination of dilute AGNS waste by conventional fluid-bed techniques was unsuccessful due to the inability to control bed particle size--both particle size and bed level decreased. Fluid-bed solidification of AGNS dilute waste at conditions in which most of the calcined solids left the calciner vessel with the off-gas was successful. In such a concept, the steady-state composition of the bed material would be approximately 22 wt percent calcined solids deposited on inert particles. Calcination of simulated NFS acid waste indicated that solidification by the fluid-bed process is feasible

Calcine Waste Storage at the Idaho Nuclear Technology and Engineering Center

Energy Technology Data Exchange (ETDEWEB)

M. D. Staiger

1999-06-01

A potential option in the program for long-term management of high-level wastes at the Idaho Nuclear Technology and Engineering Center (INTEC), at the Idaho National Engineering and Environmental Laboratory, calls for retrieving calcine waste and converting it to a more stable and less dispersible form. An inventory of calcine produced during the period December 1963 to May 1999 has been prepared based on calciner run, solids storage facilities operating, and miscellaneous operational information, which gives the range of chemical compositions of calcine waste stored at INTEC. Information researched includes calciner startup data, waste solution analyses and volumes calcined, calciner operating schedules, solids storage bin capacities, calcine storage bin distributor systems, and solids storage bin design and temperature monitoring records. Unique information on calcine solids storage facilities design of potential interest to remote retrieval operators is given.

Retrieval System for Calcined Waste for the Idaho Cleanup Project - 12104

Energy Technology Data Exchange (ETDEWEB)

Eastman, Randy L.; Johnston, Beau A.; Lower, Danielle E. [CH2M-WG Idaho, LLC. The Idaho Cleanup Project at the Idaho National Laboratory (United States)

2012-07-01

This paper describes the conceptual approach to retrieve radioactive calcine waste, hereafter called calcine, from stainless steel storage bins contained within concrete vaults. The retrieval system will allow evacuation of the granular solids (calcine) from the storage bins through the use of stationary vacuum nozzles. The nozzles will use air jets for calcine fluidization and will be able to rotate and direct the fluidization or displacement of the calcine within the bin. Each bin will have a single retrieval system installed prior to operation to prevent worker exposure to the high radiation fields. The addition of an articulated camera arm will allow for operations monitoring and will be equipped with contingency tools to aid in calcine removal. Possible challenges (calcine bridging and rat-holing) associated with calcine retrieval and transport, including potential solutions for bin pressurization, calcine fluidization and waste confinement, are also addressed. The Calcine Disposition Project has the responsibility to retrieve, treat, and package HLW calcine. The calcine retrieval system has been designed to incorporate the functions and technical characteristics as established by the retrieval system functional analysis. By adequately implementing the highest ranking technical characteristics into the design of the retrieval system, the system will be able to satisfy the functional requirements. The retrieval system conceptual design provides the means for removing bulk calcine from the bins of the CSSF vaults. Top-down vacuum retrieval coupled with an articulating camera arm will allow for a robust, contained process capable of evacuating bulk calcine from bins and transporting it to the processing facility. The system is designed to fluidize, vacuum, transport and direct the calcine from its current location to the CSSF roof-top transport lines. An articulating camera arm, deployed through an adjacent access riser, will work in conjunction with the

Comparison of the electrochemical performance of mesoscopic Cu2Sb, SnSb and Sn/SnSb alloy powders

International Nuclear Information System (INIS)

Zhang Ge; Huang Kelong; Liu Suqin; Zhang Wei; Gong Benli

2006-01-01

Cu 2 Sb, SnSb and Sn/SnSb mesoscopic alloy powders were prepared by chemical reduction, respectively. The crystal structures and particle morphology of Cu 2 Sb, SnSb and Sn/SnSb were characterized by X-ray diffraction (XRD), scanning electron microscopy (SEM). The electrochemical performances of the Cu 2 Sb, SnSb and Sn/SnSb electrodes were investigated by galvanostatic charge and discharge cycling and electrochemical impedance spectroscopy (EIS). The results showed the first charge and discharge capacities of SnSb and Sn/SnSb were higher than Cu 2 Sb, but after 15 cycles, the charge capacity fading rates of Cu 2 Sb, Sn/SnSb and Sn/SnSb were 26.16%, 55.33% and 47.39%, respectively. Cu 2 Sb had a better cycle performance, and Sn/SnSb multiphase alloy was prior to pure SnSb due to the existence of excessive Sn in Sn/SnSb system

Development and evaluation of alumina calcination

International Nuclear Information System (INIS)

Bennett, I.J.

2000-01-01

This thesis focuses on a number of aspects governing the transformation of gibbsite, via intermediate phases, to α-alumina. These aspects include the size and morphology of the gibbsite grains, the influence of additions of foreign elements, the effect of a mechanical treatment of the gibbsite prior to calcination, and combinations of these factors. The materials were characterised by scanning electron microscopy, X-ray diffraction and surface area measurements. For some of the calcined materials an attempt was made to sinter the powders to a dense body to investigate if any of the treatments during calcination had an effect on this process. The literature review covers the current state of understanding of the production of bulk alumina powder by the Bayer process and the phase changes seen on calcination of precursors to the stable α-alumina phase. A detailed description of the phase changes is given and the various routes and conditions necessary for the transformations to occur are considered. The transformations are examined in relation to the morphology of the crystals and the variables controlling the phase transformation route are discussed. Calcination in air showed that the size of the gibbsite grain governs the calcination route taken to reach oc-alumina. The standard gibbsites used in this work show a mixed calcination sequence transforming both via the boehmite phase, followed by the γ, δ and θ phases, and via the χ and κ phases. The formation of boehmite is attributed to retention of water vapour within the grain. Differences in morphology of the starting materials showed that for the range of materials seen, the morphology of the grain is less important than its size. The super fine material confirmed that a small grain size transforms via the non-boehmite route only, with the other gibbsites taking intermediate routes as for the standard gibbsites. Of the additions made prior to calcination, aluminium fluoride was found to reduce the

Microwave heating application in calcination and SYNROC formation

International Nuclear Information System (INIS)

Ambashta, R.D.; Wattal, P.K.; Malav, R.K.; Mallik, G.K.

2006-01-01

Microwave for calcination of titanate based ceramic wasteform (SYNROC) is being reported for the first time in this paper. Although major constituents in SYNROC were non microwave active, the combination with microwave active constituents rendered the mixture calcinable. Calcine was sintered at 1150 degC under hot uniaxial conditions at an applied pressure of ∼30 MPa. XRD shows presence of major phases of SYNROC in the compacted sample. (author)

Fixation of calcined waste by bituminization or cementation

International Nuclear Information System (INIS)

Napravnik, J.; Kyrs, M.; Ditl, P.

1983-01-01

The overall concept is given of the combination of calcination with fixation into bitumen, cement etc. The design is shown of a calciner with the capacity of 10 L/h which was tested on real radioactive wastes for 2000 h. The geometrical and operating parameters of the apparatus have been optimized based on a statistical evaluation of the experiments. Wastes containing nitrates are calcined at 300-550 deg. C, yielding oxides. Wastes containing sulphates, carbonates, KMnO 4 , or borates are calcined at 150-330 deg. C, yielding soluble salts. The content of H 3 BO 4 and Na 2 B 4 O 7 and in some cases of sulphates in the calcinate retards hardening of the mixture with cement. Nitrates and detergents also interfere. The effect of the above components on the products mixed with bitumen is much less. Detergents can be decomposed at 200-300 deg. C; organic acids can be reacted with A1 salts to form insoluble substances lowering the leaching rate of Sr and Cs; small amounts of SiO 2 eliminate the effect of borates on cement hardening. The drawbacks of bituminization with bitumen emulsions are the complicated preparation of the emulsion, higher leaching rate of the product and low stability of the emulsion against breaking. The leachability was determined (1-50 days) of different products containing LWR wastes: 33% of concentrated waste in cement of calcination product stabilized with PVA exhibit approx. 8x10 - 3 g/cm 2 per day, 33% of calcine in cement approx. 3x10 - 3 ; 40% concentrate fixed with bitumen emulsion approx. 9x10 - 4 ; 50% calcine stabilized with PVA in bitumen, pilot-plant scale approx. 2x10 - 5 ; the same but on a laboratory scale approx. 1.10 - 5 . (author)

Mathematical modeling of an in-line low-NOx calciner

DEFF Research Database (Denmark)

Iliuta, Ion; Dam-Johansen, Kim; Jensen, Lars Skaarup

2002-01-01

The reduction of the NOx content in in-line-calciner-type kiln systems can be made by optimization of the primary filing in the rotary kiln and of the secondary firing in the calciner. Because the optimization of calciner offers greater opportunities the mathematical modeling of this reactor...

Product removal and solids transport from fluidized-bed calciners

International Nuclear Information System (INIS)

Grimmett, E.S.; Munger, D.H.

1978-09-01

Methods of removing the solid product from pilot-plant and production fluidized-bed calciners, and transporting product to underground storage vaults are reported here. Testing of dense-phase solids transport systems in test loops during development of a 15-cm-diam. and 30-cm-diam. calciner are described. A lean-phase solid transport system is used with the Waste Calcining Facility. The results of some recent tests done in a lean-phase transport system connected to the 30-cm-diam. calciner are included in this report

Design and development of a rotary calciner for radiochemical waste

International Nuclear Information System (INIS)

Pande, D.P.; Sutar, V.D.; Sengar, P.B.S.

1997-01-01

Present experience and knowledge in handling of radioactive waste has led to identification of major thrust areas in the development of the treatment processes. In order to reduce evaporation and volatility losses in the vitrification facility, it is advantageous to carry out evaporation and calcination steps in another equipment like rotary calciner. Efforts have been directed for the engineering development of a Rotary Ball Kiln calciner. This paper highlights the important design features of the Rotary Ball Kiln Calciner for the radioactive waste. In this work, an attempt has been made to systematically evaluate the influence of process and design parameters. The results obtained on calcination will provide a design basis and rational methodology for the optimum utilization of these processes and equipment for volume reduction and calcination of the liquid waste

Optimization of Calcine Blending During Retrieval from Binsets

International Nuclear Information System (INIS)

Nelson, Lee Orville; Mohr, Charles Milton; Taylor, Dean Dalton

2000-01-01

This report documents a study performed during advanced feasibility studies for the INTEC Technology Development Facility (ITDF). The study was commissioned to provide information about functional requirements for the ITDF related to development of equipment and procedures for retrieving radioactive calcine from binset storage at the Idaho Nuclear Technology and Engineering Center (INTEC) at the Idaho National Engineering and Environmental Laboratory (INEEL). Calcine will be retrieved prior to treating it for permanent disposal in a national repository for high level waste. The objective this study was to estimate the degree of homogenization of the calcine that might be achieved through optimized retrieval and subsequent blending. Such homogenization has the potential of reducing the costs for treatment of the calcine and for qualifying of the final waste forms for acceptance at the repository. Results from the study indicate that optimized retrieval and blending can reduce the peak concentration variations of key components (Al, Zr, F) in blended batches of retrieved calcine. During un-optimized retrieval these variations are likely to be 81-138% while optimized retrieval can reduce them to the 5-10% range

Practical results of the MESA 1 line calcinator trial operation

International Nuclear Information System (INIS)

Napravnik, J.; Sazavsky, P.; Skaba, V.; Zahalka, F.; Vild, J.; Kulovany, J.

1987-01-01

Mobile calcination and cementation unit MESA 1 was designed and built by UJV Rez in cooperation with many enterprises, mainly with the Kralovopolske Strojirny Brno. This facility for direct fixation of liquid radioactive wastes was experimentally tested using model non-radioactive solutions and model and actual wastes from the Jaslovske Bohunice nuclear power plant. The calciner was run in trial operation at the Kralovopolske SAtrojirny Brno. A total of 1.3 m 3 of model solutions was processed into 180 kg of calcinate. The fixation of the calcinate in cement, the times of solidification and of hardening and the moisture content of concrete blocks were studied. The application was also tested of the calciner in drying ion exchangers from WWER-440 prior to their bituminization. Following the despatch of the cementation module to the Chernobyl nuclear power plant, the direct calcination module was tested at Dukovany together with an auxiliary module which makes possible self-contained calciner operation. Model non-radioactive solutions from the Dukovany nuclear power plant were treated containing H 3 BO 3 and NaNO 3 as main components. The usability in actual conditions of the mobile calcination and cementation unit for radioactive wastes was tested in a total of about 70 operating hours. (E.S.). 2 figs., 2 refs

Assessment of soda ash calcination treatment of Turkish trona ore

Directory of Open Access Journals (Sweden)

Gezer Sibel

2016-01-01

Full Text Available Trona is relatively rare, non-metallic mineral, Na2CO3 · NaHCO3 · 2H2O. The pure material contains 70.3% sodium carbonate and by calcination the excess CO2 and water can be driven off, yielding natural soda ash. The terms soda ash and sodium carbonate are used interchangeably. Trona calcining is a key process step in production of soda ash (sodium carbonate anhydrate from the relatively cheap trona ore. The calcination reaction may proceeds in a sequence of steps. Depending on the conditions, it may result in formation of either sodium carbonate monohydrate (Na2CO3 · H2O, sodium sesquicarbonate or weigschederite (Na2CO3 · 3NaHCO3. The Beypazarı Turkish trona deposit is the second largest deposit in the world with the content of 84% trona. The decomposition of trona appeared to be a single stage process across the temperature range studied (150-200 °C with the representative samples of different size fractions in the draught up metallurgical furnace. The optimum particle size and calcination time were −6.35 mm and 30 minutes, respectively, at calcination temperature of 175 °C in a metallurgical furnace. Microwave-induced dry calcination of trona was possible and 5 minutes of calcination time at a power level of 900 was sufficient for complete calcination of −6.35 mm feed. This includes short time calcinations with the goal of improving economics and simplifying the thermal process.

High quality InAsSb grown on InP substrates using AlSb/AlAsSb buffer layers

International Nuclear Information System (INIS)

Wu, B.-R.; Liao, C.; Cheng, K. Y.

2008-01-01

High quality InAsSb grown on semi-insulating InP substrates by molecular beam epitaxy was achieved using AlSb/AlAsSb structure as the buffer layer. A 1000 A InAsSb layer grown on top of 1 μm AlSb/AlAsSb buffer layer showed a room temperature electron mobility of ∼12 000 cm 2 /V s. High structural quality and low misfit defect density were also demonstrated in the InAsSb layer. This novel AlSb/AlAsSb buffer layer structure with the AlAsSb layer lattice matched to InP substrates could enhance the performance of optoelectronic devices utilizing 6.1 A family of compound semiconductor alloys

Optimization of Calcine Blending During Retrieval From Binsets

International Nuclear Information System (INIS)

Taylor, D.D.; Mohr, C.M.; Nelson, L.O.

2000-01-01

This report documents a study performed during advanced feasibility studies for the INTEC Technology Development Facility (ITDF). The study was commissioned to provide information about functional requirements for the ITDF related to development of equipment and procedures for retrieving radioactive calcine from binset storage at the Idaho Nuclear Technology and Engineering Center (INTEC) at the Idaho National Engineering and Environmental Laboratory (INEEL). Calcine will be retrieved prior to treating it for permanent disposal in a national repository for high level waste. The objective this study was to estimate the degree of homogenization of the calcine that might be achieved through optimized retrieval and subsequent blending. Such homogenization has the potential of reducing the costs for treatment of the calcine and for qualifying of the final waste forms for acceptance at the repository. Results from the study indicate that optimized retrieval and blending can reduce the peak c oncentration variations of key components (Al, Zr, F) in blended batches of retrieved calcine. During un-optimized retrieval these variations are likely to be 81-138% while optimized retrieval can reduce them to the 5-10% range

Pilot-plant development of a Rover waste calcination flowsheet

International Nuclear Information System (INIS)

Birrer, S.A.

1978-04-01

Results of eight runs, six using the 10-cm dia and two using the 30-cm dia pilot-plant calciners, in which simulated first-cycle Rover waste was calcined, are described. Results of the tests showed that a feed blend consisting of one volume simulated first-cycle Rover waste and one or two volumes simulated first-cycle zirconium waste could not be successfully calcined. 5 figs., 8 tables

Modeling of calcination of single kaolinitic clay particle

DEFF Research Database (Denmark)

Gebremariam, Abraham Teklay; Yin, Chungen; Rosendahl, Lasse

The present work aims at modeling of the calcination (dehydroxylation) process of clay particles, specifically kaolinite, and its thermal transformation. For such purpose, 1D single particle calcination model was developed based on the concept of shrinking core model to assess the dehydroxylation...

Development of Concentration and Calcination Technology For High Level Liquid Waste

International Nuclear Information System (INIS)

Pande, D.P.

2006-01-01

The concentrated medium and high-level liquid radio chemicals effluents contain nitric acid, water along with the dissolved chemicals including the nitrates of the radio nuclides. High level liquid waste contain mainly nitrates of cesium, strontium, cerium, zirconium, chromium, barium, calcium, cobalt, copper, pickle, iron etc. and other fission products. This concentrated solution requires further evaporation, dehydration, drying and decomposition in temperature range of 150 to 700 deg. C. The addition of the calcined solids in vitrification pot, instead of liquid feed, helps to avoid low temperature zone because the vaporization of the liquid and decomposition of nitrates do not take place inside the melter. In our work Differential and thermo gravimetric studies has been carried out in the various stages of thermal treatment including drying, dehydration and conversion to oxide forms. Experimental studies were done to characterize the chemicals present in high-level radioactive waste. A Rotary Ball Kiln Calciner was used for development of the process because this is amenable for continuous operation and moderately good heat transfer can be achieved inside the kiln. This also has minimum secondary waste and off gases generation. The Rotary Ball Kiln Calciner Demonstration facility system was designed and installed for the demonstration of calcination process. The Rotary Ball Kiln Calciner is a slowly rotating slightly inclined horizontal tube that is externally heated by means of electric resistance heating. The liquid feed is sprayed onto the moving bed of metal balls in a slowly rotating calciner by a peristaltic type-metering pump. The vaporization of the liquid occurs in the pre-calcination zone due to counter current flow of hot gases. The dehydration and denitration of the solids occurs in the calcination zone, which is externally heated by electrical furnace. The calcined powder is cooled in the post calcination portion. It has been demonstrated that the

Calcination of kaolinite clay particles for cement production

DEFF Research Database (Denmark)

Gebremariam, Abraham Teklay; Yin, Chungen; Rosendahl, Lasse

2014-01-01

Kaolinite rich clay particles calcined under certain conditions can attain favorable pozzolanic properties and can be used to substitute part of the CO2 intensive clinker in cement production. To better guide calcination of a clay material, a transient one-dimensional single particle model...

Effects of rapid calcination on properties of calcium-based sorbents

International Nuclear Information System (INIS)

Yan, Chang-Feng; Grace, John R.; Lim, C. Jim

2010-01-01

The calcination process may influence subsequent fragmentation, sintering and swelling when CaO derived from limestone acts as a CO 2 or SO 2 -sorbent in combustion, gasification and reforming. Sorbent properties are affected by CO 2 partial pressure, total pressure, temperature, heating rate, impurities and sample size. In this study, the effect of calcination heating rate was investigated based on an electrically heated platinum foil. The effects of heating rate (up to 800 C/s), calcination temperature (700-950 C), particle size (90-180 μm) and sweep gas velocity were investigated. Higher initial heating rates led to lower extents of limestone calcination, but the extents of carbonation of the resulting CaO were similar to each other. Calcium utilization declined markedly during carbonation or sulphation of CaO after calcination by rapid heating. Experimental results show that carbonation and calcium utilization were most effective for carbonation temperatures between 503 and 607 C. Increasing the extent of calcination is not the best way to improve overall calcium utilization due to the vast increase in energy consumption. (author)

CSER 99-001: PFP LAB Dentirating calciner

International Nuclear Information System (INIS)

MILLER, E.M.; DOBBIN, K.D.

1999-01-01

A criticality safety evaluation report was prepared for the Plutonium Finishing Plant (PFP) laboratory denigrating calciner, located in Glovebox 188-1, that converts Pu(NO 3 ) 4 solutions to the high fired stable oxide PuO 2 . Fissile mass limits and volume limits are set for the glovebox for testing operations and training operators using only nitric acid feed to a plutonium oxide bed in the calciner

Fluidized bed calciner

International Nuclear Information System (INIS)

Sheely, W.F.

1986-01-01

A unique way to convert radioactive scrap into useful nuclear fuel products was developed for the Department of Energy at Hanford. An advanced, fluidized bed calciner is used to convert metallic nitrate scrap or waste solutions into benign, solid and gaseous products. There are broad potential applications of this concept beyond those in the nuclear industry

Properties of Formula 127 glass prepared with radioactive zirconia calcine

International Nuclear Information System (INIS)

Staples, B.A.; Pavlica, D.A.; Cole, H.S.

1982-09-01

Formula 127 glass has been developed to immobilize ICPP zirconia calcine. This glass has been prepared remotely on a laboratory scale basis with actual radioactive zirconia calcine retrieved after ten years of storage from Bin Set 2. The aqueous leachability of the glass produced was investigated and compared through application of the MCC-1, MCC-2 and Soxhlet leach tests with that of Formula 127 glass prepared with simulated calcine. The solid state properties of the glasses prepared with actual and simulated calcines were also measured by electron spectroscopy for chemical analysis (ESCA) and scanning electron microscopy energy dispersive x-ray (SEM-EDX). Based on the application of these leaching tests and analysis techniques the properties measured in this study are similar for 127 glass prepared with either simulated or radioactive calcine. 13 figures, 16 tables

Growth and characterization of an InSb infrared photoconductor on Si via an AlSb/GaSb buffer

Science.gov (United States)

Jia, Bo Wen; Tan, Kian Hua; Loke, Wan Khai; Wicaksono, Satrio; Yoon, Soon Fatt

2018-05-01

A 99.6% relaxed InSb layer is grown on a 6° offcut (1 0 0) Si substrate via an AlSb/GaSb buffer using molecular beam epitaxy (MBE). A 200 nm GaSb buffer is first grown on Si and the lattice mismatch between them is accommodated by an interfacial misfit (IMF) array consisting of uniformly distributed 90° misfit dislocations. Si delta doping is introduced during the growth of GaSb to reduce the density of threading dislocation. Subsequently, a 50 nm AlSb buffer is grown followed by a 0.8 μm InSb layer. The InSb layer exhibits a 300 K electron mobility of 22,300 cm2/Vs. An InSb photoconductor on Si is demonstrated with a photoconductive gain from 77 K to 200 K under a 700 °C maintained blackbody.

DWPF SB6 Initial CPC Flowsheet Testing SB6-1 TO SB6-4L Tests Of SB6-A And SB6-B Simulants

International Nuclear Information System (INIS)

Lambert, D.; Pickenheim, B.; Best, D.

2009-01-01

The Defense Waste Processing Facility (DWPF) will transition from Sludge Batch 5 (SB5) processing to Sludge Batch 6 (SB6) processing in late fiscal year 2010. Tests were conducted using non-radioactive simulants of the expected SB6 composition to determine the impact of varying the acid stoichiometry during the Sludge Receipt and Adjustment Tank (SRAT) and Slurry Mix Evaporator (SME) processes. The work was conducted to meet the Technical Task Request (TTR) HLW/DWPF/TTR-2008-0043, Rev.0 and followed the guidelines of a Task Technical and Quality Assurance Plan (TT and QAP). The flowsheet studies are performed to evaluate the potential chemical processing issues, hydrogen generation rates, and process slurry rheological properties as a function of acid stoichiometry. These studies were conducted with the estimated SB6 composition at the time of the study. This composition assumed a blend of 101,085 kg of Tank 4 insoluble solids and 179,000 kg of Tank 12 insoluble solids. The current plans are to subject Tank 12 sludge to aluminum dissolution. Liquid Waste Operations assumed that 75% of the aluminum would be dissolved during this process. After dissolution and blending of Tank 4 sludge slurry, plans included washing the contents of Tank 51 to ∼1M Na. After the completion of washing, the plan assumes that 40 inches on Tank 40 slurry would remain for blending with the qualified SB6 material. There are several parameters that are noteworthy concerning SB6 sludge: (1) This is the second batch DWPF will be processing that contains sludge that has had a significant fraction of aluminum removed through aluminum dissolution; (2) The sludge is high in mercury, but the projected concentration is lower than SB5; (3) The sludge is high in noble metals, but the projected concentrations are lower than SB5; and(4) The sludge is high in U and Pu - components that are not added in sludge simulants. Six DWPF process simulations were completed in 4-L laboratory-scale equipment using

Synthesis, structural and semiconducting properties of Ba(Cu1/3 Sb2/3)O3-PbTiO3 solid solutions

Science.gov (United States)

Singh, Chandra Bhal; Kumar, Dinesh; Prashant, Verma, Narendra Kumar; Singh, Akhilesh Kumar

2018-05-01

We report the synthesis and properties of a new solid solution 0.05Ba(Cu1/3Sb2/3)O3-0.95PbTiO3 (BCS-PT) which shows the semiconducting properties. In this study, we have designed new perovskite-type (ABO3) solid solution of BCS-PT that have tunable optical band gap. BCS-PT compounds were prepared by conventional solid-state reaction method and their structural, micro-structural and optical properties were analyzed. The calcination temperature for BCS-PT solid solutions has been optimized to obtain a phase pure system. The Reitveld analysis of X-ray data show that all samples crystallize in tetragonal crystal structure with space group P4mm. X-ray investigation revealed that increase in calcination temperature led to increase of lattice parameter `a' while `c' parameter value lowered. The band gap of PbTiO3 is reduced from 3.2 eV to 2.8 eV with BCS doping and with increasing calcination temperature it further reduces to 2.56 eV. The reduced band gap indicated that the compounds are semiconducting and can be used for photovoltaic device applications.

Optimization of Calcine Blending During Retrieval From Binsets; TOPICAL

International Nuclear Information System (INIS)

Taylor, D.D.; Mohr, C.M.; Nelson, L.O.

2000-01-01

This report documents a study performed during advanced feasibility studies for the INTEC Technology Development Facility (ITDF). The study was commissioned to provide information about functional requirements for the ITDF related to development of equipment and procedures for retrieving radioactive calcine from binset storage at the Idaho Nuclear Technology and Engineering Center (INTEC) at the Idaho National Engineering and Environmental Laboratory (INEEL). Calcine will be retrieved prior to treating it for permanent disposal in a national repository for high level waste. The objective this study was to estimate the degree of homogenization of the calcine that might be achieved through optimized retrieval and subsequent blending. Such homogenization has the potential of reducing the costs for treatment of the calcine and for qualifying of the final waste forms for acceptance at the repository. Results from the study indicate that optimized retrieval and blending can reduce the peak c oncentration variations of key components (Al, Zr, F) in blended batches of retrieved calcine. During un-optimized retrieval these variations are likely to be 81-138% while optimized retrieval can reduce them to the 5-10% range

Calcinating petroleum coke in a furnace with a rotating hearth

Energy Technology Data Exchange (ETDEWEB)

Akhmetov, M M; Ezhov, B M; Galeeva, Z G; Goriunov, V S; Karpinskaia, N N; Zaitseva, S A

1980-01-01

A scheme is described for an industrial device with a bottom furnace for calcinating coke from slow coking. The consumption and operational indicators of the process during the calcination of standard and needle cokes are given, together with data on the quality of dry and calcinated cokes under different conditions. The basic drawbacks in the operation of the device are described, and measures are proposed for increasing its operational effectiveness.

Leaching properties and chemical compositions of calcines produced at the Idaho Chemical Processing Plant

International Nuclear Information System (INIS)

Staples, B.A.; Paige, B.E.; Rhodes, D.W.; Wilding, M.W.

1980-01-01

No significant chemical differences were determined between retrieved and fresh calcine based on chemical and spectrochemical analyses. Little can be derived from the amounts of the radioisotopes present in the retrieved calcine samples other than the ratios of strontium-90 to cesium-137 are typical of aged fission product. The variations in concentrations of radionuclides within the composite samples of each bin also reflect the differences in compositions of waste solutions calcined. In general the leaching characteristics of both calcines by distilled water are similar. In both materials the radionuclides of cesium and strontium were selectively leached at significant rates, although cesium leached much more completely from the alumina calcine than from the zirconia calcine. Cesium and strontium are probably contained in both calcines as nitrate salts and also as fluoride salts in zirconia calcine, all of which are at least slightly soluble in water. Radionuclides of cerium, ruthenium, and plutonium in both calcines were highly resistant to leaching and leached at rates similar to or less than those of the matrix elements. These elements exist as polyvalent metal ions in the waste solutions before calcination and they probably form insoluble oxides and fluorides in the calcine. The relatively slow leaching of nitrate ion from zirconia calcine and radiocesium from both calcines suggests that the calcine matrix in some manner prevents complete or immediate contact of the soluble ions with water. Whether radiostrontium forms slightly fluoride salts or forms nitrate salts which are protected in the same manner as radiocesium is unknown. Nevertheless, selective leaching of cesium and strontim is retarded in some manner by the calcine matrix

Dissimilatory Sb(V) reduction by microorganisms isolated from Sb-contaminated sediment

Science.gov (United States)

Dovick, M. A.; Kulp, T. R.

2013-12-01

Mining and smelting are major sources of trace metal contamination in freshwater systems. Arsenic (As) is a common contaminant derived from certain mining operations and is a known toxic metalloid and carcinogen. Antimony (Sb) is listed as a pollutant of priority interest by the EPA and is presumed to share similar geochemical and toxicological properties with arsenic. Both elements can occur in four different oxidation states (V, III, 0, and -III) under naturally occurring conditions. In aqueous solutions As(V) and Sb(V) predominate in oxygenated surface waters whereas As(III) and Sb(III) are stable in anoxic settings. Numerous studies have examined microbiological redox pathways that utilize As(V) as a terminal electron acceptor for anaerobic respiration, however there have been few studies on microbial mechanisms that may affect the biogeochemical cycling of Sb in the environment. Here we report bacterial reduction of Sb(V) to Sb(III) in anoxic enrichment cultures and bacterial isolates grown from sediment collected from an Sb contaminated pond at a mine tailings site in Idaho (total pond water Sb concentration = 235.2 +/- 136.3 ug/L). Anaerobic sediment microcosms (40 mL) were established in artificial freshwater mineral salt medium, amended with millimolar concentrations of Sb(V), acetate or lactate, and incubated at 27°C for several days. Antimony(V), lactate, and acetate concentrations were monitored during incubation by High Performance Liquid Chromatography (HPLC) and Ion Chromatography (IC). Live sediment microcosms reduced millimolar amendments of Sb(V) to Sb(III) coupled to the oxidation of acetate and lactate, while no activity occurred in killed controls. Enrichment cultures were established by serially diluting Sb(V)-reducing microcosms in mineral salt medium with Sb(V) and acetate, and a Sb(V)-reducing bacterial strain was isolated by plating on anaerobic agar plates amended with millimolar Sb(V) and acetate. Direct cell counting demonstrated that

Sb{sup III} - Sb{sup V} Exchange Reaction in Hydrochloric: Acid Solutions; Echange Sb{sup III}-Sb{sup V} dans des Solutions d'Acide Chlorhydrique; Reaktsiya obmena Sb(III) - Sb(V) v rastvorakh khloristovodorodnoj kisloty; Intercambio Sb{sup III}-Sb{sup V} en Soluciones de HCl

Energy Technology Data Exchange (ETDEWEB)

Kambara, T.; Yamaguchi, K.; Yasuba, S. [Shizuoka University, Shizuoka City (Japan)

1965-10-15

The exchange reaction of Sb{sup III} - Sb{sup V} in solutions of low HCl concentrations was studied using {sup 124}Sb as a tracer. The effects of HCl concentrations and chemical forms of antimony on the exchange rate were investigated. The HCl concentrations of the antimony solutions ((Sb{sup III}) =(Sb{sup V}) = 6.8 x 10{sup -4}M) were changed from 0.8 to 4.0M and the half-time for the exchange was measured by plotting log (1 - F) versus time t to calculate the exchange rate assuming the second-ordet reaction. It was found that the exchange rate was sharply increased with the increase of HCl concentrations (at 25 Degree-Sign C, from 0.8 to 2.0M) and at 2.0M HCl concentration the rate reached the maximum, from which the rate was decreased with the increase of HCl concentrations (at 25 Degree-Sign C, from 2.0 to 4.0M). Two sorts of Sb{sup V} species were used for our investigations, i.e. one was used directly after the dilution of 10M HCl Sb{sup V} solution with water and the other was used after 24 hours standing at room temperature from the dilution. (The Sb{sup III} species were also kept standing after preparation from 10M HCl Sb{sup III} solution.) In both cases the maximum rates were found to exist at 2.0M HCl concentration. The rate R{sub 1} for the former (directly after dilution) was 4.5 x 10{sup -6} mole litre{sup -1} min{sup -1} and the rate R{sub 2} for the latter (24 hours standing) was 1.2 x 10{sup -}{sub 6} mole litre. Also the activation energy for these cases was found to be 12.2 kcal/mole and 19.1 kcal/mole. By spectrophotometric studies, the Sb{sup V} species of the former type were found to be mainly consisting of SbCl{sup -}{sub 6} and the species of the latter type to be of SbCl{sub 4}(OH){sup -}{sub 2}, etc. Besides these facts the form of Sb{sup III} species was found to have no influence on the exchange rate. A much sharper increase of the exchange rate was observed when the HCl concentration of the antimony solution was fixed at 0.8M and

Calcined Waste Storage at the Idaho Nuclear Technology and Engineering Center

Energy Technology Data Exchange (ETDEWEB)

M. D. Staiger

2007-06-01

This report provides a quantitative inventory and composition (chemical and radioactivity) of calcined waste stored at the Idaho Nuclear Technology and Engineering Center. From December 1963 through May 2000, liquid radioactive wastes generated by spent nuclear fuel reprocessing were converted into a solid, granular form called calcine. This report also contains a description of the calcine storage bins.

High Temperature Calcination - MACT Upgrade Equipment Pilot Plant Test

Energy Technology Data Exchange (ETDEWEB)

Richard D. Boardman; B. H. O& #39; Brien; N. R. Soelberg; S. O. Bates; R. A. Wood; C. St. Michel

2004-02-01

About one million gallons of acidic, hazardous, and radioactive sodium-bearing waste are stored in stainless steel tanks at the Idaho Nuclear Technology and Engineering Center (INTEC), which is a major operating facility of the Idaho National Engineering and Environmental Laboratory. Calcination at high-temperature conditions (600 C, with alumina nitrate and calcium nitrate chemical addition to the feed) is one of four options currently being considered by the Department of Energy for treatment of the remaining tank wastes. If calcination is selected for future processing of the sodium-bearing waste, it will be necessary to install new off-gas control equipment in the New Waste Calcining Facility (NWCF) to comply with the Maximum Achievable Control Technology (MACT) standards for hazardous waste combustors and incinerators. This will require, as a minimum, installing a carbon bed to reduce mercury emissions from their current level of up to 7,500 to <45 {micro}g/dscm, and a staged combustor to reduce unburned kerosene fuel in the off-gas discharge to <100 ppm CO and <10 ppm hydrocarbons. The staged combustor will also reduce NOx concentrations of about 35,000 ppm by 90-95%. A pilot-plant calcination test was completed in a newly constructed 15-cm diameter calciner vessel. The pilot-plant facility was equipped with a prototype MACT off-gas control system, including a highly efficient cyclone separator and off-gas quench/venturi scrubber for particulate removal, a staged combustor for unburned hydrocarbon and NOx destruction, and a packed activated carbon bed for mercury removal and residual chloride capture. Pilot-plant testing was performed during a 50-hour system operability test January 14-16, followed by a 100-hour high-temperature calcination pilot-plant calcination run January 19-23. Two flowsheet blends were tested: a 50-hour test with an aluminum-to-alkali metal molar ratio (AAR) of 2.25, and a 50-hour test with an AAR of 1.75. Results of the testing

Criticality safety analysis of a calciner exit chute

International Nuclear Information System (INIS)

Haught, C.F.; Basoglu, B.; Brewer, R.W.; Hollenback, D.F.; Wilkinson, A.D.; Dodds, H.L.

1994-01-01

Calcination of uranyl nitrate into uranium oxide is part of normal operations of some enrichment plants. Typically, a calciner discharges uranium oxide powder (U 3 O 8 ) into an exit chute that directs the powder into a receiving can located in a glove box. One possible scenario for a criticality accident is the exit chute becoming blocked with powder near its discharge. The blockage restricts the flow of powder causing the exit chute to become filled with the powder. If blockage does occur, the height of the powder could reach a level that would not be safe from a criticality point of view. In this analysis, the subcritical height limit is examined for 98% enriched U 3 O 8 in the exit chute with full water reflection and optimal water moderation. The height limit for ensuring criticality safety during such an accumulation is 28.2 cm above the top of the discharge pipe at the bottom of the chute. Chute design variations are also evaluated with full water reflection and optimal water moderation. Subcritical configurations for the exit chute variation are developed, but the configurations are not safe when combined with the calciner. To ensure criticality safety, modifications must be made to the calciner tube or safety measures must be implemented if these designs are to be utilized with 98% enriched material. A geometrically safe configuration for the exit chute is developed for a blockage of 20% enriched powder with full water reflection and optimal water moderation, and this configuration is safe when combined with the existing calciner

Sorghum phytochrome B inhibits flowering in long days by activating expression of SbPRR37 and SbGHD7, repressors of SbEHD1, SbCN8 and SbCN12.

Directory of Open Access Journals (Sweden)

Shanshan Yang

Full Text Available Light signaling by phytochrome B in long days inhibits flowering in sorghum by increasing expression of the long day floral repressors PSEUDORESPONSE REGULATOR PROTEIN (SbPRR37, Ma1 and GRAIN NUMBER, PLANT HEIGHT AND HEADING DATE 7 (SbGHD7, Ma6. SbPRR37 and SbGHD7 RNA abundance peaks in the morning and in the evening of long days through coordinate regulation by light and output from the circadian clock. 58 M, a phytochrome B deficient (phyB-1, ma3R genotype, flowered ∼60 days earlier than 100 M (PHYB, Ma3 in long days and ∼11 days earlier in short days. Populations derived from 58 M (Ma1, ma3R, Ma5, ma6 and R.07007 (Ma1, Ma3, ma5, Ma6 varied in flowering time due to QTL aligned to PHYB/phyB-1 (Ma3, Ma5, and GHD7/ghd7-1 (Ma6. PHYC was proposed as a candidate gene for Ma5 based on alignment and allelic variation. PHYB and Ma5 (PHYC were epistatic to Ma1 and Ma6 and progeny recessive for either gene flowered early in long days. Light signaling mediated by PhyB was required for high expression of the floral repressors SbPRR37 and SbGHD7 during the evening of long days. In 100 M (PHYB the floral activators SbEHD1, SbCN8 and SbCN12 were repressed in long days and de-repressed in short days. In 58 M (phyB-1 these genes were highly expressed in long and short days. Furthermore, SbCN15, the ortholog of rice Hd3a (FT, is expressed at low levels in 100 M but at high levels in 58 M (phyB-1 regardless of day length, indicating that PhyB regulation of SbCN15 expression may modify flowering time in a photoperiod-insensitive manner.

Self-diffusion in 69Ga121Sb/71Ga123Sb isotope heterostructures

Science.gov (United States)

Bracht, H.; Nicols, S. P.; Haller, E. E.; Silveira, J. P.; Briones, F.

2001-05-01

Gallium and antimony self-diffusion experiments have been performed in undoped 69Ga121Sb/71Ga123Sb isotope heterostructures at temperatures between 571 and 708 °C under Sb- and Ga-rich ambients. Ga and Sb profiles measured with secondary ion mass spectrometry reveal that Ga diffuses faster than Sb by several orders of magnitude. This strongly suggests that the two self-atom species diffuse independently on their own sublattices. Experimental results lead us to conclude that Ga and Sb diffusion are mediated by Ga vacancies and Sb interstitials, respectively, and not by the formation of a triple defect proposed earlier by Weiler and Mehrer [Philos. Mag. A 49, 309 (1984)]. The extremely slow diffusion of Sb up to the melting temperature of GaSb is proposed to be a consequence of amphoteric transformations between native point defects which suppress the formation of those native defects which control Sb diffusion. Preliminary experiments exploring the effect of Zn indiffusion at 550 °C on Ga and Sb diffusion reveal an enhanced intermixing of the Ga isotope layers compared to undoped GaSb. However, under the same conditions the diffusion of Sb was not significantly affected.

Kinetic Study of Calcination of Jakura Limestone Using Power Rate ...

African Journals Online (AJOL)

National Research Institute for Chemical Technology, P.M. B 1052, Zaria, ... calcination of Jakura limestone was also found to be first order reaction with respect to CaCO3 ... Keywords: Jakura, limestone, calcination, kinetics, power law model.

Physical and chemical characterization of synthetic calcined sludge

International Nuclear Information System (INIS)

Slates, R.V.; Mosley, W.C. Jr.; Tiffany, B.; Stone, J.A.

1982-03-01

Calcined synthetic sludge was chemically characterized in support of engineering studies to design a processing plant to solidify highly radioactive waste at the Savannah River Plant. An analytical technique is described which provides quantitative data by mass spectrometric analysis of gases evolved during thermogravimetric analysis without measurements of gas flow rates or mass spectrometer sensitivities. Scanning electron microprobe analysis, Mossbauer spectroscopy, and several other common analytical methods were also used. Calcined sludge consists primarily of amorphous particles of hydrous oxides with iron, manganese, nickel, and calcium distributed fairly uniformly throughout the powder. Iron, manganese, nickel, and calcium exist in forms that are highly insoluble in water, but aluminum, sulfate, nitrate, and sodium exhibit relative water solubilities that increase in the given order from 60% to 94%. Evolved gas analysis in a helium atmosphere showed that calcined sludge is completely dehydrated by heating to 400 0 C, carbon dioxide is evolved between 100 to 700 0 C with maximum evolution at 500 0 C, and oxygen is evolved between 400 and 1000 0 C. Evolved gas analyses are also reported for uncalcined sludge. A spinel-type oxide similar to NiFe 2 O 4 was detected by x-ray diffraction analysis at very low-level in calcined sludge

Microstructural changes in porous hematite nanoparticles upon calcination

DEFF Research Database (Denmark)

Johnsen, Rune; Knudsen, Kenneth D.; Molenbroek, Alfons M.

2011-01-01

This combined study using small-angle neutron scattering (SANS), X-ray powder diffraction (XRPD), transmission electron microscopy (TEM) and adsorption isotherm techniques demonstrates radical changes in the microstructure of porous hematite (-Fe2O3) nanoparticles upon calcination in air. TEM....... The change in microstructure also causes a reduction in the surface area as calculated by gaseous adsorption. The XRPD and SANS data show that the crystallite and SANS particle sizes are virtually unchanged by calcination at 623 K. Calcination at 973 K induces a significant alteration of the sample. The XRPD...... data reveal that the crystallite size increases significantly, and the SANS and adsorption isotherm studies suggest that the specific surface area decreases by a factor of 5–6. The TEM images show that the particles are sintered into larger agglomerates, but they also show that parts of the porous...

Calcination of Rod-like Hydroxyapatite Nanocrystals with an Anti-sintering Agent Surrounding the Crystals

International Nuclear Information System (INIS)

Okada, M.; Furuzono, T.

2007-01-01

Sintering-free nanocrystals of calcined hydroxyapatite (HAp) having a rod-like morphology were fabricated by calcination at 800 deg. C for 1 h with an anti-sintering agent surrounding original HAp particles and the agent was subsequently removed after calcination. The original HAp particles having a rod-like morphology with a size ranging from 30 to 80 nm (short axis) and 300 to 500 nm (long axis) were prepared by wet chemical process, and poly(acrylic acid, calcium salt) (PAA-Ca) was used as the anti-sintering agent. In the case of calcination without additives, the mean size of HAp crystals dispersed in an ethanol medium increased by about 4 times and the specific surface area of the crystals exhibited a 25% decrease compared to those of the original HAp particles because of calcination-induced sintering among the crystals. On the other hand, the HAp crystals calcined with the anti-sintering agent, PAA-Ca, could be dispersed in an ethanol medium at the same size as the original particles, and they preserved the specific surface area after calcination. These results indicate that PAA-Ca and/or its thermally decomposed product, CaO, surrounded the HAp particles and protected them against calcination-induced sintering during calcination. The HAp crystals calcined with PAA-Ca showed high crystallinity, and no other calcium phosphate phases could be detected after washing with water

ICPP calcined solids storage facility closure study. Volume III: Engineering design files

International Nuclear Information System (INIS)

1998-02-01

The following information was calculated to support cost estimates and radiation exposure calculations for closure activities at the Calcined Solids Storage Facility (CSSF). Within the estimate, volumes were calculated to determine the required amount of grout to be used during closure activities. The remaining calcine on the bin walls, supports, piping, and floor was also calculated to approximate the remaining residual calcine volumes at different stages of the removal process. The estimates for remaining calcine and vault void volume are higher than what would actually be experienced in the field, but are necessary for bounding purposes. The residual calcine in the bins may be higher than was is experienced in the field as it was assumed that the entire bin volume is full of calcine before removal activities commence. The vault void volumes are higher as the vault roof beam volumes were neglected. The estimations that follow should be considered rough order of magnitude, due to the time constraints as dictated by the project's scope of work. Should more accurate numbers be required, a new analysis would be necessary

ICPP calcined solids storage facility closure study. Volume III: Engineering design files

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-02-01

The following information was calculated to support cost estimates and radiation exposure calculations for closure activities at the Calcined Solids Storage Facility (CSSF). Within the estimate, volumes were calculated to determine the required amount of grout to be used during closure activities. The remaining calcine on the bin walls, supports, piping, and floor was also calculated to approximate the remaining residual calcine volumes at different stages of the removal process. The estimates for remaining calcine and vault void volume are higher than what would actually be experienced in the field, but are necessary for bounding purposes. The residual calcine in the bins may be higher than was is experienced in the field as it was assumed that the entire bin volume is full of calcine before removal activities commence. The vault void volumes are higher as the vault roof beam volumes were neglected. The estimations that follow should be considered rough order of magnitude, due to the time constraints as dictated by the project`s scope of work. Should more accurate numbers be required, a new analysis would be necessary.

Process Design Concepts for Stabilization of High Level Waste Calcine

Energy Technology Data Exchange (ETDEWEB)

T. R. Thomas; A. K. Herbst

2005-06-01

The current baseline assumption is that packaging ¡§as is¡¨ and direct disposal of high level waste (HLW) calcine in a Monitored Geologic Repository will be allowed. The fall back position is to develop a stabilized waste form for the HLW calcine, that will meet repository waste acceptance criteria currently in place, in case regulatory initiatives are unsuccessful. A decision between direct disposal or a stabilization alternative is anticipated by June 2006. The purposes of this Engineering Design File (EDF) are to provide a pre-conceptual design on three low temperature processes under development for stabilization of high level waste calcine (i.e., the grout, hydroceramic grout, and iron phosphate ceramic processes) and to support a down selection among the three candidates. The key assumptions for the pre-conceptual design assessment are that a) a waste treatment plant would operate over eight years for 200 days a year, b) a design processing rate of 3.67 m3/day or 4670 kg/day of HLW calcine would be needed, and c) the performance of waste form would remove the HLW calcine from the hazardous waste category, and d) the waste form loadings would range from about 21-25 wt% calcine. The conclusions of this EDF study are that: (a) To date, the grout formulation appears to be the best candidate stabilizer among the three being tested for HLW calcine and appears to be the easiest to mix, pour, and cure. (b) Only minor differences would exist between the process steps of the grout and hydroceramic grout stabilization processes. If temperature control of the mixer at about 80„aC is required, it would add a major level of complexity to the iron phosphate stabilization process. (c) It is too early in the development program to determine which stabilizer will produce the minimum amount of stabilized waste form for the entire HLW inventory, but the volume is assumed to be within the range of 12,250 to 14,470 m3. (d) The stacked vessel height of the hot process vessels

Mission Need Statement: Calcine Disposition Project Major Systems Acquisition Project

International Nuclear Information System (INIS)

J. T. Beck

2007-01-01

This document identifies the need to establish the Calcine Disposition Project to determine and implement the final disposition of calcine including characterization, retrieval, treatment (if necessary), packaging, loading, onsite interim storage pending shipment to a repository or interim storage facility, and disposition of related facilities

Dissolution of two NWCF calcines: Extent of dissolution and characterization of undissolved solids

International Nuclear Information System (INIS)

Brewer, K.N.; Herbst, R.S.; Tranter, T.J.

1995-01-01

A study was undertaken to determine the dissolution characteristics of two NWCF calcine types. A two-way blended calcine made from 4 parts nonradioactive aluminum nitrate and one part WM-102 was studied to determine the extent of dissolution for aluminum-type calcines. A two-way blend of 3.5 parts fluorinel waste from WM-187 and 1 part sodium waste from WM-185 was used to determine the extent of dissolution for zirconium-type calcines. This study was necessary to develop suitable aqueous separation flowsheets for the partitioning of actinides and fission products from ICPP calcines and to determine the disposition of the resulting undissolved solids (UDS). The dissolution flowsheet developed by Herbst was used to dissolve these two NWCF calcine types. Results show that greater than 95 wt% of aluminum and zirconium calcine types were dissolved after a single batch contact with 5 M HNO 3 . A characterization of the UDS indicates that the weight percent of TRU elements in the UDS resulting from both calcine type dissolutions increases by approximately an order of magnitude from their concentrations prior to dissolution. Substantial activities of cesium and strontium are also present in the UDS resulting from the dissolution of both calcine types. Multiple TRU, Cs, and Sr analyses of both UDS types show that these solids are relatively homogeneous. From this study, it is estimated that between 63.5 and 635 cubic meters of UDS will be generated from the dissolution of 3800 M 3 of calcine. The significant actinide and fission product activities in these UDS will preclude their disposal as low-level waste. If the actinide and fission activity resulting from the UDS is the only considered source in the dissolved calcine solutions, an estimated 99.9 to 99.99 percent of the solids must be removed from this solution for it to meet non-TRU Class A low-level waste

Recovery of gold and uranium from calcines

Energy Technology Data Exchange (ETDEWEB)

Livesey-Goldblatt, E.

1981-10-06

The invention concerns the recovery of non-ferrous metals, such as gold, uranium or the like from iron oxide containing calcines which have the non-ferrous metal present in solid solution and/or encapsulated within the iron oxide. The calcine is reacted, while stirring vigorously, with sulphuric acid or another strong inorganic acid to cause the iron to form the ferric salt. The material obtained is mixed with water and the liquid and solid phases are separated from each other. The non-ferrous metal is then obtained from at least one of these phases by leaching, or the like.

Applied laboratory research of high-level waste denitration and calcination technologies

International Nuclear Information System (INIS)

Napravnik, J.

1977-01-01

Denitration and calcination processes are assessed for model solutions of high-level radioactive wastes. The kinetics was studied of the reaction of HNO 3 with HCOOH with respect to the final composition of the gaseous product. A survey is presented of used denitration agents and of reaction processes. Calcination was studied both as associated with denitration in a single technological step and separately. Also studied was the pyrolysis and chemical decomposition of sodium nitrate which forms an indecomposable melt in the temperature region of 320 to 850 degC under normal conditions. Based on the experiments a laboratory unit was designed and produced for the denitration and calcination of model solutions of high-level radioactive wastes operating in a temperature range of 100 to 550 degC with a capacity of 1000 ml/h. A boiler type stirred evaporator with electric heating (3 kW) was chosen for the denitration unit while a vertical calcinator modified from a film evaporator with a thermal input of 4 kW was chosen for the calcination unit. (B.S.)

RECONSTRUCTION OF CALCINED Zn -Al LAYERED DOUBLE HYDROXIDES DURING TETRACYCLINE ADSORPSION

Directory of Open Access Journals (Sweden)

G. M. Starukh

2015-12-01

Full Text Available Zn-Al mixed oxides containing ZnO different degree crystallinity were obtained by calcinations of Zn-Al layered double hydroxides (LDHs. The reconstruction of calcined Zn-Al LDHs has been performed under stirring in aqueous suspensions. The assynthesized LDHs, its decomposition products, as well as the reconstructed solids upon hydration were characterized by XRD, N2adsorption, differential and thermal gravimetric analysis. It was found that the ability of Zn-Al LDHs to recover a layered structure under the hydration of mixed oxides depends on the degree of ZnO crystallinity. The partial reconstruction of Zn-Al layered structure occurs in tetracycline solutions irrespective to the degree of ZnO crystallinity in calcined LDHs. Calcined Zn-Al LDHs demonstrate the higher adsorption capacity to tetracycline in comparison with as-prepared Zn-Al LDHs. The adsorption of TC on calcined and uncalcined ZnAl LDHs occurs on the centers of one particular type. It is suggested that surface complexation of the A-ring ligand of TC with Al-OH centers takes place.

Letter report: Evaluation of dryer/calciner technologies for testing

International Nuclear Information System (INIS)

Sevigny, G.

1996-02-01

This letter report describes some past experiences on the drying and calcination of radioactive materials or corresponding simulants; and the information needed from testing. The report also includes an assessment of informational needs including possible impacts to a full-scale plant. This includes reliability, maintenance, and overall size versus throughput. Much of the material was previously compiled and reported by Mike Elliott of PNL open-quotes Melter Performance Assessmentclose quotes and Larry Eisenstatt of SEG on contract to WHC in a letter to Rod Powell. Also, an annotated bibliography was prepared by Reagan Seymour of WHC. Descriptions of the drying and calciner technologies, development status, advantages and disadvantages of using a WFE or calciner, and recommendations for future testing are discussed in this report

Inductive classification of operating data from a fluidized bed calciner

International Nuclear Information System (INIS)

O'Brien, B.H.

1990-01-01

A process flowsheet expert system for a fluidized bed calciner which solidifies high-level radioactive liquid waste was developed from pilot-plant data using a commercial, inductive classification program. After initial classification of the data, the resulting rules were inspected and adjusted to match existing knowledge of process chemistry. The final expert system predicts performance of process flowsheets based upon the chemical composition of the calciner feed and has been successfully used to identify potential operational problems prior to calciner pilot-plant testing of new flowsheets and to provide starting parameters for pilot-plant tests. By using inductive classification techniques to develop the initial rules from the calciner pilot-plant data and using existing process knowledge to verify the accuracy of these rules, an effective expert system was developed with a minimum amount of effort. This method may be applied for developing expert systems for other processes where numerous operating data are available and only general process chemistry effects are known

Density functional simulations of Sb-rich GeSbTe phase change alloys

International Nuclear Information System (INIS)

Gabardi, S; Bernasconi, M; Caravati, S; Parrinello, M

2012-01-01

We generated models of the amorphous phase of Sb-rich GeSbTe phase change alloys by quenching from the melt within density functional molecular dynamics. We considered the two compositions Ge 1 Sb 1 Te 1 and Ge 2 Sb 4 Te 5 . Comparison with previous results on the most studied Ge 2 Sb 2 Te 5 allowed us to draw some conclusions on the dependence of the structural properties of the amorphous phase on the alloy composition. Vibrational and electronic properties were also scrutinized. Phonons at high frequencies above 200 cm -1 are localized in tetrahedra around Ge atoms in Sb-rich compounds as well as in Ge 2 Sb 2 Te 5 . All compounds are semiconducting in the amorphous phase, with a band gap in the range 0.7-1.0 eV.

Density functional simulations of Sb-rich GeSbTe phase change alloys

Science.gov (United States)

Gabardi, S.; Caravati, S.; Bernasconi, M.; Parrinello, M.

2012-09-01

We generated models of the amorphous phase of Sb-rich GeSbTe phase change alloys by quenching from the melt within density functional molecular dynamics. We considered the two compositions Ge1Sb1Te1 and Ge2Sb4Te5. Comparison with previous results on the most studied Ge2Sb2Te5 allowed us to draw some conclusions on the dependence of the structural properties of the amorphous phase on the alloy composition. Vibrational and electronic properties were also scrutinized. Phonons at high frequencies above 200 cm-1 are localized in tetrahedra around Ge atoms in Sb-rich compounds as well as in Ge2Sb2Te5. All compounds are semiconducting in the amorphous phase, with a band gap in the range 0.7-1.0 eV.

Effects of Coke Calcination Level on Pore Structure in Carbon Anodes

Science.gov (United States)

Fang, Ning; Xue, Jilai; Lang, Guanghui; Bao, Chongai; Gao, Shoulei

2016-02-01

Effects of coke calcination levels on pore structure of carbon anodes have been investigated. Bench anodes were prepared by 3 types of cokes with 4 calcination temperatures (800°C, 900°C, 1000°C and 1100°C). The cokes and anodes were characterized using hydrostatic method, air permeability determination, mercury porosimetry, image analysis and confocal microscopy (CSLM). The cokes with different calcination levels are almost the same in LC values (19-20 Å) and real density (1.967-1.985 g/cm3), while the anode containing coke calcined at 900°C has the lowest open porosity and air permeability. Pore size distribution (represented by Anode H sample) can be roughly divided into two ranges: small and medium pores in diameter of 10-400 μm and large pores of 400-580 μm. For the anode containing coke calcined at 800°C, a number of long, narrow pores in the pore size range of 400-580 μm are presented among cokes particles. Formation of these elongated pores may be attributed to coke shrinkages during the anode baking process, which may develop cracking in the anode under cell operations. More small or medium rounded pores with pore size range of 10-400 μm emerge in the anodes with coke calcination temperatures of 900°C, 1000°C and 1100°C, which may be generated due to release of volatiles from the carbon anode during baking. For the anode containing coke calcined at 1100°C, it is found that many rounded pores often closely surround large coke particles, which have potential to form elongated, narrow pores.

Self-diffusion in 69Ga121Sb/71Ga123Sb isotope heterostructures

OpenAIRE

Bracht, H.; Nicols, S. P.; Haller, E. E.; Silveira, Juan Pedro; Briones Fernández-Pola, Fernando

2001-01-01

Gallium and antimony self-diffusion experiments have been performed in undoped 69Ga121Sb/71Ga123Sb isotope heterostructures at temperatures between 571 and 708 °C under Sb- and Ga-rich ambients. Ga and Sb profiles measured with secondary ion mass spectrometry reveal that Ga diffuses faster than Sb by several orders of magnitude. This strongly suggests that the two self-atom species diffuse independently on their own sublattices. Experimental results lead us to conclude that Ga and Sb diffusio...

Silicon-Polymer Encapsulation of High-Level Calcine Waste for Transportation or Disposal

International Nuclear Information System (INIS)

Loomis, G.G.; Miller, C.M.; Giansiracusa, J.A.; Kimmel, R.; Prewett, S.V.

2000-01-01

This report presents the results of an experimental study investigating the potential uses for silicon-polymer encapsulation of High Level Calcine Waste currently stored within the Idaho Nuclear Technology and Engineering Center (INTEC) at the Idaho National Engineering and Environmental Laboratory (INEEL). The study investigated two different applications of silicon polymer encapsulation. One application uses silicon polymer to produce a waste form suitable for disposal at a High Level Radioactive Waste Disposal Facility directly, and the other application encapsulates the calcine material for transportation to an offsite melter for further processing. A simulated waste material from INTEC, called pilot scale calcine, which contained hazardous materials but no radioactive isotopes was used for the study, which was performed at the University of Akron under special arrangement with Orbit Technologies, the originators of the silicon polymer process called Polymer Encapsulation Technology (PET). This document first discusses the PET process, followed by a presentation of past studies involving PET applications to waste problems. Next, the results of an experimental study are presented on encapsulation of the INTEC calcine waste as it applies to transportation or disposal of calcine waste. Results relating to long-term disposal include: (1) a characterization of the pilot calcine waste; (2) Toxicity Characteristic Leaching Procedure (TCLP) testing of an optimum mixture of pilot calcine, polysiloxane and special additives; and, (3) Material Characterization Center testing MCC-1P evaluation of the optimum waste form. Results relating to transportation of the calcine material for a mixture of maximum waste loading include: compressive strength testing, 10-m drop test, melt testing, and a Department of Transportation (DOT) oxidizer test

CALCIUM OXIDE CHARACTERISTICS PREPARED FROM AMBUNTEN’S CALCINED LIMESTONE

Directory of Open Access Journals (Sweden)

Fatimatul Munawaroh

2018-05-01

Full Text Available Calcium oxide (CaO and calcium carbonate (CaCO3 are widely used in industry. CaO and CaCO3 can be synthesized or derived from limestone. The purpose of this study to determine the characteristics of CaO calcined limestone from Ambunten Sumenep. Lime in calcined at 850 ° C for 6 hours. Characterization of X-ray fluorescence (XRF was conducted to determine the chemical composition of limestone, X-ray diffraction test (XRD to find the lime crystalline phase and FTIR test to determine the absorption of wave number. XRF test results showed that the limestone chemical composition consisted of Ca of 95.37% as the dominant element, Mg of 4.1%, Fe 0.17% and Y by 0.39%. The XRD test results showed that the limestone crystal phase is ankerite (Ca [Fe, Mg] [CO3] 2 and after the calcined phase calcination is vaterite (Ca [OH] 2, calcite (CaO and calcite (CaCO3. While the FTIR test results show that the CaO spectra are seen at 3741.24, 1417.12 and 874.14 cm-1.

LITERATURE REVIEW OF PUO2 CALCINATION TIME AND TEMPERATURE DATA FOR SPECIFIC SURFACE AREA

Energy Technology Data Exchange (ETDEWEB)

Daniel, G.

2012-03-06

The literature has been reviewed in December 2011 for calcination data of plutonium oxide (PuO{sub 2}) from plutonium oxalate Pu(C{sub 2}O{sub 4}){sub 2} precipitation with respect to the PuO{sub 2} specific surface area (SSA). A summary of the literature is presented for what are believed to be the dominant factors influencing SSA, the calcination temperature and time. The PuO{sub 2} from Pu(C{sub 2}O{sub 4}){sub 2} calcination data from this review has been regressed to better understand the influence of calcination temperature and time on SSA. Based on this literature review data set, calcination temperature has a bigger impact on SSA versus time. However, there is still some variance in this data set that may be reflecting differences in the plutonium oxalate preparation or different calcination techniques. It is evident from this review that additional calcination temperature and time data for PuO{sub 2} from Pu(C{sub 2}O{sub 4}){sub 2} needs to be collected and evaluated to better define the relationship. The existing data set has a lot of calcination times that are about 2 hours and therefore may be underestimating the impact of heating time on SSA. SRNL recommends that more calcination temperature and time data for PuO{sub 2} from Pu(C{sub 2}O{sub 4}){sub 2} be collected and this literature review data set be augmented to better refine the relationship between PuO{sub 2} SSA and its calcination parameters.

The influence of calcination on the physical and chemical properties of petroleum and mixed cokes

Energy Technology Data Exchange (ETDEWEB)

Sikora, K; Syrek, H

1980-01-01

Freshly prepared petroleum and coal-petroleum cokes, before utilization for the production of various materials, are subjected to calcining--thermal treatment in a neutral or reducing atmosphere without the admission of air at less than or equal to 1400/sup 0/. During calcining, stabilization of the physical and chemical properties of the cokes takes place. The properties of the obtained coke depend chiefly on the calcining time and temperature. During calcining, volatile substances are removed almost completely from the coke; the coke density is increased, and its structure is put in order; the electrical conductivity is improved; the mechanical strength is increased; and the reactivity of the coke is decreased. Laboratory studies were conducted on calcining mixed coal-petroleum cokes of two grades at 1200, 1250, and 1300/sup 0/ for 2-6 h. In the calcining products the content of volatile substances, the ash content, S content, and density were determined. It was ascertained that calcining of mixed coal-petroleum cokes goes analogously to calcining of pure petroleum cokes. Raising the temperature and increasing the time of calcining has a substantial effect on improvement of coke physical and chemical properties. For high-quality coke, calcining is to be carried out at greater than or equal to 1300/sup 0/ for 4-6 h, for ordinary coke at > 1200/sup 0/ and greater than or equal to 4 h. The results are regarded as starting data for an industrial study of the calcining process.

Stop Smoking—Tube-In-Tube Helical System for Flameless Calcination of Minerals

Directory of Open Access Journals (Sweden)

Nils Haneklaus

2017-11-01

Full Text Available Mineral calcination worldwide accounts for some 5–10% of all anthropogenic carbon dioxide (CO2 emissions per year. Roughly half of the CO2 released results from burning fossil fuels for heat generation, while the other half is a product of the calcination reaction itself. Traditionally, the fuel combustion process and the calcination reaction take place together to enhance heat transfer. Systems have been proposed that separate fuel combustion and calcination to allow for the sequestration of pure CO2 from the calcination reaction for later storage/use and capture of the combustion gases. This work presents a new tube-in-tube helical system for the calcination of minerals that can use different heat transfer fluids (HTFs, employed or foreseen in concentrated solar power (CSP plants. The system is labeled ‘flameless’ since the HTF can be heated by other means than burning fossil fuels. If CSP or high-temperature nuclear reactors are used, direct CO2 emissions can be divided in half. The technical feasibility of the system has been accessed with a brief parametric study here. The results suggest that the introduced system is technically feasible given the parameters (total heat transfer coefficients, mass- and volume flows, outer tube friction factors, and –Nusselt numbers that are examined. Further experimental work will be required to better understand the performance of the tube-in-tube helical system for the flameless calcination of minerals.

Density functional simulations of Sb-rich GeSbTe phase change alloys

OpenAIRE

Gabardi, S; Caravati, S; Bernasconi, M; Parrinello, M

2012-01-01

We generated models of the amorphous phase of Sb rich GeSbTe phase change alloys by quenching from the melt within density functional molecular dynamics. We considered the two compositions Ge 1Sb 1Te 1 and Ge 2Sb 4Te 5. Comparison with previous results on the most studied Ge 2Sb 2Te 5 allowed us to draw some conclusions on the dependence of the structural properties of the amorphous phase on the alloy composition. Vibrational and electronic properties were also scrutinized. Phonons at high fr...

Influence of calcination temperature on the structure and morphology of HAp bioceramics

International Nuclear Information System (INIS)

Teixeira, C.M.L.; Santos, P.T.A.; Rodrigues, P.A.; Costa, A.C.F.M.

2012-01-01

This study aimed to evaluate the influence of calcination temperature on the structure and morphology of samples of hydroxyapatite (HAp) synthesized by the wet method. For hydroxyapatite was used as precursor solutions of calcium hydroxide and phosphoric acid 1M solution of calcium hydroxide was stirred and heated to 80 ° C and then dropwise with a solution of phosphoric acid. After the liquid was evaporated without an oven at 110 ° C and sieved. The sample of PA as synthesized was submitted to calcination at 900 °C and 1100 °C / 2 hours. The samples as synthesized and after calcination were characterized by XRD, XRF, FTIR, SEM. The XRD showed the presence of phase hydroxyapatite for samples without calcining and both calcination temperatures studied. FTIR spectra showed bands group and PO 4 3- , CO 3 2- . Through the SEM micrograph, there is the formation of agglomerates in the form of porous flakes approximately spherical shape. (author)

Compositional and structural characterisation of GaSb and GaInSb

International Nuclear Information System (INIS)

Corregidor, V.; Alves, E.; Alves, L.C.; Barradas, N.P.; Duffar, Th.; Franco, N.; Marques, C.; Mitric, A.

2005-01-01

Low band gap III-V semiconductors are researched for applications in thermophotovoltaic technology. GaSb crystal is often used as a substrate. Ga 1-x In x Sb is also a promising substrate material, because its lattice parameters can be adjusted by controlling x. We used a new method to synthesise GaSb and GaInSb, in which a high frequency alternate magnetic field is used to heat, to melt and to mix the elements. We present a compositional and structural characterisation of the materials using a combination of complementary techniques. Rutherford backscattering was used to determine accurately the composition of the GaSb. With proton induced X-ray emission in conjunction with a 3 x 3 μm 2 micro-beam we studied the homogeneity of the samples. Structural analysis and phase identification were done with X-ray diffraction. The results for GaSb show a homogeneous composition while the GaInSb samples were found to be strongly heterogeneous at the end of the ingot. The ingots produced are competitive feed material, when compared to other growth techniques, to be used in a second step for the production of good quality ternary crystals

Defect Structure of High-Temperature-Grown GaMnSb/GaSb

International Nuclear Information System (INIS)

Romanowski, P.; Bak-Misiuk, J.; Dynowska, E.; Domagala, J.Z.; Wojciechowski, T.; Jakiela, R.; Sadowski, J.; Barcz, A.; Caliebe, W.

2010-01-01

GaMnSb/GaSb(100) layers with embedded MnSb inclusions have been grown at 720 K using MBE technique. This paper presents the investigation of the defect structure of Ga1-xMnxSb layers with different content of manganese (up to x = 0.07). X-ray diffraction method using conventional and synchrotron radiation was applied. Dimensions and shapes of inclusions were detected by scanning electron microscopy. Depth profiles of elements were measured using secondary ion mass spectroscopy technique. (authors)

Removal of Dissolved Silica using Calcinated Hydrotalcite in Real-life Applications.

Energy Technology Data Exchange (ETDEWEB)

Sasan, Koroush [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Brady, Patrick Vane. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Krumhansl, James L. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Nenoff, Tina M. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sasan, Koroush [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sasan, Koroush [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-09-01

Water shortages are a growing global problem. Reclamation of industrial and municipal wastewater will be necessary in order to mitigate water scarcity. However, many operational challenges, such as silica scaling, prevent large scale water reuse. Previously, our team at Sandia has demonstrated the use of selective ion exchange materials, such as calcinated hydrotalcite (HTC, (Mg ₆ Al ₂ (OH) ₁₆ (CO ₃ )*4H ₂ O)), for the low cost removal of silica from synthetic cooling tower water. However, it is not currently know if calcinated HTC has similar capabilities in realistic applications. The purpose of this study was to investigate the ability of calcinated HTC to remove silica from real cooling tower water. This was investigated under both batch and continuous conditions, and in the presence of competing ions. It was determined that calcinated HTC behaved similarly in real and synthetic cooling tower water; the HTC is highly selective for the silica even in the presence of competing cations. Therefore, the data concludes that calcinated HTC is a viable anti-scaling pretreatment for the reuse of industrial wastewaters.

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

International Nuclear Information System (INIS)

COMPTON, J.A.

2000-01-01

Stored solutions containing plutonium and nitric acid and possibly uranium thorium and minor amounts of other substances will be used for development and demonstration of a vertical calciner direct denitration process for conversion of those to stable storable PuO 2 rich solids. Some of those solutions are quite dilute and very impure these require either pretreatment to make them suitable for calciner feed or an alternate stabilization method. Untreated scrap solutions containing some amounts of sulfate phosphate sodium and/or potassium may also be tested for suitability of direct denitration for conversion directly to PuO 2 -rich solids. A vertical calciner will be used to demonstrate the direct denitration process for converting plutonium-bearing liquors to stable plutonium-rich solids. The calciner and some of its ancillary equipment were previously tested with non-radioactive chemicals to demonstrate operability

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

International Nuclear Information System (INIS)

COMPTON, J.A.

2000-01-01

Stored solutions containing plutonium and nitric acid and possibly uranium thorium and minor amounts of other substances will be used for development and demonstration of a vertical calciner direct denitration process for conversion of those to stable storable PuO 2 rich solids. Some of those solutions are quite dilute and very impure these require either pretreatment to make them suitable for calciner feed or an alternate stabilization method. Untreated scrap solutions containing some amounts of sulfate phosphate sodium and/or potassium may also be tested for suitability of direct denitration for conversion directly to PuO 2 -rich solids. A vertical calciner will be used to demonstrate the direct denitration process for converting plutonium-bearing liquors to stable plutonium rich solids. The calciner and some of its associated equipment were previously tested with non-radioactive chemicals to demonstrate operability

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

Energy Technology Data Exchange (ETDEWEB)

COMPTON, J.A.

2000-02-03

Stored solutions containing plutonium and nitric acid and possibly uranium thorium and minor amounts of other substances will be used for development and demonstration of a vertical calciner direct denitration process for conversion of those to stable storable PuO{sub 2} rich solids. Some of those solutions are quite dilute and very impure these require either pretreatment to make them suitable for calciner feed or an alternate stabilization method. Untreated scrap solutions containing some amounts of sulfate phosphate sodium and/or potassium may also be tested for suitability of direct denitration for conversion directly to PuO{sub 2}-rich solids. A vertical calciner will be used to demonstrate the direct denitration process for converting plutonium-bearing liquors to stable plutonium-rich solids. The calciner and some of its ancillary equipment were previously tested with non-radioactive chemicals to demonstrate operability.

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

Energy Technology Data Exchange (ETDEWEB)

COMPTON, J.A.

2000-02-03

Stored solutions containing plutonium and nitric acid and possibly uranium thorium and minor amounts of other substances will be used for development and demonstration of a vertical calciner direct denitration process for conversion of those to stable storable PuO{sub 2} rich solids. Some of those solutions are quite dilute and very impure these require either pretreatment to make them suitable for calciner feed or an alternate stabilization method. Untreated scrap solutions containing some amounts of sulfate phosphate sodium and/or potassium may also be tested for suitability of direct denitration for conversion directly to PuO{sub 2}-rich solids. A vertical calciner will be used to demonstrate the direct denitration process for converting plutonium-bearing liquors to stable plutonium rich solids. The calciner and some of its associated equipment were previously tested with non-radioactive chemicals to demonstrate operability.

Activity Based Startup Plan for Prototype Vertical Denitration Calciner

International Nuclear Information System (INIS)

SUTTER, C.S.

1999-01-01

Testing activation on the Prototype Vertical Denitration Calciner at PFP were suspended in January 1997 due to the hold on fissile material handling in the facility. The restart of testing activities will require a review through an activity based startup process based upon Integrated Safety Management (ISM) principles to verify readiness. The Activity Based Startup Plan for the Prototype vertical Denitration Calciner has been developed for this process

Remotely replaceable fuel and feed nozzles for the NWCF calciner vessel

International Nuclear Information System (INIS)

Fletcher, R.D.; Carter, J.A.; May, K.W.

1978-01-01

The development and testing of remotely replaceable fuel and feed nozzles for calcination of liquid radioactive wastes in the calciner vessel of the New Waste Calcining Facility (NWCF) being built at the Idaho National Engineering Laboratory are described. A complete fuel nozzle assembly was fabricated and tested at the Remote Maintenance Development Facility to evolve design refinements, identify required support equipment, and develop handling techniques. The design also provided for remote replacement of the nozzle support carriage and adjacent feed and fuel pipe loops using two pairs of master-slave manipulators

Sequential and simultaneous adsorption of Sb(III) and Sb(V) on ferrihydrite: Implications for oxidation and competition.

Science.gov (United States)

Qi, Pengfei; Pichler, Thomas

2016-02-01

Antimony (Sb) is a naturally occurring element of growing environmental concern whose toxicity, adsorption behavior and other chemical properties are similar to that of arsenic (As). However, less is known about Sb compared to As. Individual and simultaneous adsorption experiments with Sb(III) and Sb(V) were conducted in batch mode with focus on the Sb speciation of the remaining liquid phase during individual Sb(III) adsorption experiments. The simultaneous adsorption and oxidation of Sb(III) was confirmed by the appearance of Sb(V) in the solution at varying Fe/Sb ratios (500, 100 and 8) and varying pH values (3.8, 7 and 9). This newly formed Sb(V) was subsequently removed from solution at a Fe/Sb ratio of 500 or at a pH of 3.8. However, more or less only Sb(V) was observed in the liquid phase at the end of the experiments at lower Fe/Sb ratios and higher pH, indicating that competition took place between the newly formed Sb(V) and Sb(III), and that Sb(III) outcompeted Sb(V). This was independently confirmed by simultaneous adsorption experiments of Sb(III) and Sb(V) in binary systems. Under such conditions, the presence of Sb(V) had no influence on the adsorption of Sb(III) while Sb(V) adsorption was significantly inhibited by Sb(III) over a wide pH range (4-10). Thus, in the presence of ferrihydrite and under redox conditions, which allow the presence of both Sb species, Sb(V) should be the dominant species in aquatic environments, since Sb(III) is adsorbed preferentially and at the same time oxidized to Sb(V). Copyright © 2015 Elsevier Ltd. All rights reserved.

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

International Nuclear Information System (INIS)

COMPTON, J.A.

1999-01-01

A vertical calciner will be used to demonstrate the direct denitration process for converting plutonium-bearing liquors to stable plutonium rich solids. The calciner and some of its associated equipment were previously tested with non-radioactive chemicals to demonstrate operability

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

Energy Technology Data Exchange (ETDEWEB)

COMPTON, J.A.

1999-10-05

A vertical calciner will be used to demonstrate the direct denitration process for converting plutonium-bearing liquors to stable plutonium rich solids. The calciner and some of its associated equipment were previously tested with non-radioactive chemicals to demonstrate operability.

Synthesis and thermoelectric properties of Sb{sub 0.20}CoSb{sub 2.80} skutterudite

Energy Technology Data Exchange (ETDEWEB)

Figueirêdo, C.A., E-mail: camila_fig@hotmail.com [Universidade Federal do Rio Grande do Sul, PGCIMAT, Instituto de Física, 91501-970 Porto Alegre, RS (Brazil); Gallas, M.R. [Universidade Federal do Rio Grande do Sul, PGCIMAT, Instituto de Física, 91501-970 Porto Alegre, RS (Brazil); Institute for Multiscale Simulations, Friedrich-Alexander-Universität, Nägelsbachstrasse 49b, 91052 Erlangen (Germany); Zorzi, J.E. [Universidade de Caxias do Sul, Instituto de Materiais Cerâmicos, 95765-000 Bom Princípio, RS (Brazil); Perottoni, C.A. [Universidade Federal do Rio Grande do Sul, PGCIMAT, Instituto de Física, 91501-970 Porto Alegre, RS (Brazil); Universidade de Caxias do Sul, Instituto de Materiais Cerâmicos, 95765-000 Bom Princípio, RS (Brazil)

2014-06-15

Highlights: • A HP-HT Sb{sub 0.20}CoSb{sub 2.80} phase was prepared by processing cobalt antimonide at 7.7 GPa and 550 °C, for (at least) 5 min. • The mechanism of formation of this phase involves (i) decomposition of cobalt antimonide into CoSb{sub 2} and Sb, and (ii) insertion of Sb into the remaining cobalt antimonide. • The mechanism of formation is qualitatively different from that responsible for the formation of the high pressure (greater than 20 GPa) phase. - Abstract: Polycrystalline samples of cobalt antimonide (CoSb{sub 2.79}) were submitted to different conditions of pressure, temperature and processing time, in a high-pressure toroidal-type chamber, aiming to maximize the production of the high pressure phase previously observed in experiments with a diamond anvil cell. Rietveld refinements of X-ray powder diffraction data were performed to determine the phase composition and structural parameters. The maximum yield, 89(2) wt.% of Sb{sub x}CoSb{sub 3−x} phase, was obtained at 7.7 GPa, 550 °C and (at least) 5 min of processing time. The mechanism behind the formation of Sb{sub x}CoSb{sub 3−x} at high pressure and high temperature is actually not the same as that previously inferred from experiments at higher pressures (20 GPa) and room temperature with the diamond anvil cell. Indeed, evidences suggest that, at high pressure and high temperature, Sb{sub x}CoSb{sub 3−x} is formed by insertion of Sb resulting from decomposition of cobalt antimonide. Thermal conductivity, Seebeck coefficient and electrical conductivity were estimated for CoSb{sub 2.79} and Sb{sub 0.20}CoSb{sub 2.80}. The thermoelectric figure of merit at room temperature for Sb{sub 0.20}CoSb{sub 2.80} resulted 33% greater than that for CoSb{sub 2.79}.

Redundant Sb condensation on GaSb epilayers grown by molecular beam epitaxy during cooling procedure

International Nuclear Information System (INIS)

Arpapay, B.; Şahin, S.; Arıkan, B.; Serincan, U.

2014-01-01

The effect of four different cooling receipts on the surface morphologies of unintentionally-doped GaSb epilayers on GaSb (100) substrates grown by molecular beam epitaxy is reported. Those receipts include three different Sb beam equivalent pressure (BEP) levels and two different termination temperatures. Surface morphologies of epilayers were examined by wet etching, surface profiler, atomic force microscopy, scanning electron microscopy and Raman spectroscopy. The results demonstrate that during the cooling period, a Sb BEP of 4.00 × 10 −4 Pa at a termination temperature of 400 °C induces a smooth surface without Sb condensation whereas same Sb BEP at a termination temperature of 350 °C forms a 300 nm thick Sb layer on the surface. In addition, it is revealed that by applying a wet etching procedure and using a surface profiler it is possible to identify this condensed layer from the two-sloped feature of mesa profile. - Highlights: • Sb beam flux termination temperature is crucial for redundant Sb condensation. • Sb beam flux level has a role on the thickness of redundant condensed Sb layer. • Redundant Sb layer thickness can be measured by two-sloped mesa structure

Calcining natural zeolites to improve their effect on cementitious mixture workability

International Nuclear Information System (INIS)

Seraj, Saamiya; Ferron, Raissa D.; Juenger, Maria C.G.

2016-01-01

Despite the benefits to long-term concrete durability, the use of natural zeolites as supplementary cementitious materials (SCMs) is uncommon due to their high water demand. The motivation of the research presented here was to better understand how the physical and chemical characteristics of natural zeolites influenced the workability of cementitious mixtures and whether those properties could be modified through calcination to mitigate the high water demand of natural zeolites. In this research, three different natural zeolites were characterized in their original and calcined states using x-ray diffraction (XRD) and Brunauer–Emmett–Teller (BET) surface area measurements. Rheology experiments were then conducted on cementitious pastes containing these natural zeolites, in their original and calcined states, to assess mixture viscosity and yield stress. Results showed that calcination destabilized the structure of the natural zeolites and reduced their surface area, which led to an improvement in mixture viscosity and yield stress.

Hole-dominated transport in InSb nanowires grown on high-quality InSb films

Energy Technology Data Exchange (ETDEWEB)

Algarni, Zaina; George, David; Singh, Abhay; Lin, Yuankun; Philipose, U., E-mail: usha.philipose@unt.edu [University of North Texas, Department of Physics (United States)

2016-12-15

We have developed an effective strategy for synthesizing p-type indium antimonide (InSb) nanowires on a thin film of InSb grown on glass substrate. The InSb films were grown by a chemical reaction between Sb{sub 2}S{sub 3} and In and were characterized by structural, compositional, and optical studies. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies reveal that the surface of the substrate is covered with a polycrystalline InSb film comprised of sub-micron sized InSb islands. Energy dispersive X-ray (EDX) results show that the film is stoichiometric InSb. The optical constants of the InSb film, characterized using a variable-angle spectroscopic ellipsometer (VASE) shows a maximum value for refractive index at 3.7 near 1.8 eV, and the extinction coefficient (k) shows a maximum value 3.3 near 4.1 eV. InSb nanowires were subsequently grown on the InSb film with 20 nm sized Au nanoparticles functioning as the metal catalyst initiating nanowire growth. The InSb nanowires with diameters in the range of 40–60 nm exhibit good crystallinity and were found to be rich in Sb. High concentrations of anions in binary semiconductors are known to introduce acceptor levels within the band gap. This un-intentional doping of the InSb nanowire resulting in hole-dominated transport in the nanowires is demonstrated by the fabrication of a p-channel nanowire field effect transistor. The hole concentration and field effect mobility are estimated to be ≈1.3 × 10{sup 17} cm{sup −3} and 1000 cm{sup 2} V{sup −1} s{sup −1}, respectively, at room temperature, values that are particularly attractive for the technological implications of utilizing p-InSb nanowires in CMOS electronics.

InSb semiconductors and (In,Mn)Sb diluted magnetic semiconductors. Growth and properties

Energy Technology Data Exchange (ETDEWEB)

Tran, Lien

2011-04-13

This dissertation describes investigations of the growth by molecular beam epitaxy and the characterization of the semiconductor InSb as well as the diluted magnetic semiconductor (DMS) In{sub 1-x}Mn{sub x}Sb. The InSb films were grown on GaAs (001) substrate and Si (001) offcut by 4 toward (110) substrate up to a thickness of about 2 {mu}m, in spite of a large lattice mismatch between the epi-layer and substrate (14.6% between InSb and GaAs, and 19.3% between InSb and Si). After optimizing the growth conditions, the best InSb films grown directly on GaAs without any special technique results in a high crystal quality, low noise, and an electron mobility of 41100 cm{sup 2}/V s Vs with associated electron concentration of 2.9.10{sup 6} cm{sup -3} at 300 K. Such structures could be used, for example, for infrared detector structures. The growth of InSb on Si, however, is a challenge. In order to successfully grow InSb on Si, tilted substrates and the insertion of buffer layers were used, which helps to reduce the lattice mismatch as well as the formation of defects, and hence to improve the crystal quality. An electron mobility of 24000 cm{sup 2}/V s measured at 300 K, with an associated carrier concentration of 2.6.10{sup 1}6 cm{sup -3} is found for the best sample that was grown at 340 C with a 0.06 {mu}m-thick GaSb/AlSb superlattice buffer layer. The smaller value of electron mobility (compared to the best GaAsbased sample) is related to a higher density of microtwins and stacking faults as well as threading dislocations in the near-interface region as shown by transmission electron microscopy. Deep level noise spectra indicate the existence of deep levels in both GaAs and Si-based samples. The samples grown on Si exhibit the lowest Hooge factor at 300 K, lower than the samples grown on GaAs. Taking the optimized growth conditions of InSb/GaAs, the diluted magnetic semiconductor In{sub 1-x}Mn{sub x}Sb/GaAs (001) is prepared by adding a few percent of Mn into the

Model of fragmentation of limestone particles during thermal shock and calcination in fluidised beds

Energy Technology Data Exchange (ETDEWEB)

Saastamoinen, J.; Pikkarainen, T.; Tourunen, A.; Rasanen, M.; Jantti, T. [VTT Technical Research Center, Jyvaskyla (Finland)

2008-11-15

Fragmentation of limestone due to thermal shock and calcination in a fluidised bed was studied through experiments and modelling. The time for heating was estimated by model calculations and the time for calcination by measurements. Fragmentation due to thermal shock was carried out by experiments in a CO{sub 2} atmosphere in order to prevent the effect of calcination. It was found to be much less than fragmentation due to calcination. Average particle sizes before and after fragmentation are presented for several types of limestone. The effects of particle size and gas composition on the primary fragmentation were studied through experiments. Increasing the fluidisation velocity increased the tendency to fragment. The evolution of the particle size distribution (PSD) of limestone particles due to thermal shock and during calcination (or simultaneous calcination and sulphation) were calculated using a population balance model. Fragmentation due to thermal shock is treated as an instantaneous process. The fragmentation frequency during calcination is presented as exponentially decaying over time. In addition to the final PSD, this model also predicts the PSD during the calcination process. The fragmentation was practically found to end after 10 min. Furthermore. a population balance method to calculate the particle size distribution and amount of limestone in fluidised beds in dynamic and steady state, when feeding history is known, is presented.

Zr3NiSb7: a new antimony-enriched ZrSb2 derivative

Directory of Open Access Journals (Sweden)

V. Romaka

2008-08-01

Full Text Available Single crystals of trizirconium nickel heptaantimonide were synthesized from the constituent elements by arc-melting. The compound crystallizes in a unique structure type and belongs to the family of two-layer structures. All crystallographically unique atoms (3 × Zr, 1 × Ni and 7 × Sb are located at sites with m symmetry. The structure contains `Zr2Ni2Sb5' and `Zr4Sb9' fragments and might be described as a new ZrSb2 derivative with a high Sb content.

Design and performance of a full-scale spray calciner for nonradioactive high-level-waste-vitrification studies

International Nuclear Information System (INIS)

Miller, F.A.

1981-06-01

In the spray calcination process, liquid waste is spray-dried in a heated-wall spray dryer (termed a spray calciner), and then it may be combined in solid form with a glass-forming frit. This mixture is then melted in a continuous ceramic melter or in an in-can melter. Several sizes of spray calciners have been tested at PNL- laboratory scale, pilot scale and full scale. Summarized here is the experience gained during the operation of PNL's full-scale spray calciner, which has solidified approx. 38,000 L of simulated acid wastes and approx. 352,000 L of simulated neutralized wastes in 1830 h of processing time. Operating principles, operating experience, design aspects, and system descriptions of a full-scale spray calciner are discussed. Individual test run summaries are given in Appendix A. Appendices B and C are studies made by Bechtel Inc., under contract by PNL. These studies concern, respectively, feed systems for the spray calciner process and a spray calciner vibration analysis. Appendix D is a detailed structural analysis made at PNL of the spray calciner. These appendices are included in the report to provide a complete description of the spray calciner and to include all major studies made concerning PNL's full-scale spray calciner

Lower lattice thermal conductivity in SbAs than As or Sb monolayers: a first-principles study.

Science.gov (United States)

Guo, San-Dong; Liu, Jiang-Tao

2017-12-06

Phonon transport in group-VA element (As, Sb and Bi) monolayer semiconductors has been widely investigated in theory, and, of them, monolayer Sb (antimonene) has recently been synthesized. In this work, phonon transport in monolayer SbAs is investigated with a combination of first-principles calculations and the linearized phonon Boltzmann equation. It is found that the lattice thermal conductivity of monolayer SbAs is lower than those of both monolayer As and Sb, and the corresponding sheet thermal conductance is 28.8 W K -1 at room temperature. To understand the lower lattice thermal conductivity in monolayer SbAs than those in monolayer As and Sb, the group velocities and phonon lifetimes of monolayer As, SbAs and Sb are calculated. The calculated results show that the group velocities of monolayer SbAs are between those of monolayer As and Sb, but that the phonon lifetimes of SbAs are smaller than those of both monolayer As and Sb. Hence, the low lattice thermal conductivity in monolayer SbAs is attributed to very small phonon lifetimes. Unexpectedly, the ZA branch has very little contribution to the total thermal conductivity, only 2.4%, which is obviously different from those of monolayer As and Sb with very large contributions. This can be explained by very small phonon lifetimes for the ZA branch of monolayer SbAs. The lower lattice thermal conductivity of monolayer SbAs compared to that of monolayer As or Sb can be understood by the alloying of As (Sb) with Sb (As), which should introduce phonon point defect scattering. We also consider the isotope and size effects on the lattice thermal conductivity. It is found that isotope scattering produces a neglectful effect, and the lattice thermal conductivity with a characteristic length smaller than 30 nm can reach a decrease of about 47%. These results may offer perspectives on tuning the lattice thermal conductivity by the mixture of multiple elements for applications of thermal management and

Redox calcination study of Synroc D powder containing simulated SRL waste

International Nuclear Information System (INIS)

Chen, C.

1982-01-01

According to Ringwood [A.E. Ringwood, W. Sinclair, and G.M. McLaughlin, Nuclear Waste Immobilization, Lawrence Livermore Laboratory, Livermore, Rept. UCRL-15147 (1979)], the iron oxidation state is important in controlling, the spinel mineralogy and composition if the amount of titania (TiO 2 ) consumed in spinel formation is to be minimized in favor of the formation of the Synroc phases, zirconolite, perovskite, and nepheline. In our redox calcination studies we observed that the iron oxidation state of FeO/Fe 2 O 3 can be controlled by the redoxcalcining atmosphere. In a CO atmosphere, the oxidation state was reduced to less than 7 wt % Fe 2 O 3 . With appropriate CO 2 /CO gas mixtures the resultant iron oxidation states were in the range of 45 to 59 wt % Fe 2 O 3 . Direct rotary redox calcination of spray dried powder at 600 0 C, without prior air calcination, showed increased redox efficiency when compared to powder that had been previously air calcined at 650 0 C. We believe this is caused by a reduction in particle size. Rotary calcination at 800 0 C in argon has no measurable reduction affect on the iron oxidation state of Synroc D powder

Tetrahedral 1B4Sb nanoclusters in GaP:(B, Sb)

Energy Technology Data Exchange (ETDEWEB)

Elyukhin, V A, E-mail: elyukhin@cinvestav.m [Departamento de Ingenieria Electrica-SEES, CINVESTAV-IPN, Avenida IPN 2508, Col. San Pedro Zacatenco, C. P. 07360, Mexico, D. F. (Mexico)

2009-05-01

Self-assembling conditions of 1B4Sb tetrahedral nanoclusters in GaP doped with boron and Sb isoelectronic impurities are represented in the ultradilute and dilute limits of the boron and Sb contents, respectively. The fulfilled estimates demonstrated the preferential complete or almost complete allocation of boron atoms in 1B4Sb nanoclusters at temperatures of 500 {sup 0}C and 900 {sup 0}C, respectively. The significant decrease of the sum of the free energies of the constituent compounds is the main origin of self-assembling. The reduction of the strain energy is the additional cause of this phenomenon.

Distribution, speciation and availability of antimony (Sb) in soils and terrestrial plants from an active Sb mining area

International Nuclear Information System (INIS)

Okkenhaug, Gudny; Zhu Yongguan; Luo Lei; Lei Ming; Li Xi; Mulder, Jan

2011-01-01

Here, we present one of the first studies investigating the mobility, solubility and the speciation-dependent in-situ bioaccumulation of antimony (Sb) in an active Sb mining area (Xikuangshan, China). Total Sb concentrations in soils are high (527-11,798 mg kg -1 ), and all soils, including those taken from a paddy field and a vegetable garden, show a high bioavailable Sb fraction (6.3-748 mg kg -1 ), dominated by Sb(V). Elevated concentrations in native plant species (109-4029 mg kg -1 ) underpin this. Both chemical equilibrium studies and XANES data suggest the presence of Ca[Sb(OH) 6 ] 2 , controlling Sb solubility. A very close relationship was found between the citric acid extractable Sb in plants and water or sulfate extractable Sb in soil, indicating that citric acid extractable Sb content in plants may be a better predictor for bioavailable Sb in soil than total acid digestible Sb plant content. - Highlights: → Antimony (Sb) in soils from an active Sb mining area is highly bioavailable. → Sb occurs mainly as Sb(V) in Sb mining impacted soils and plants. → Sb solubility in Sb mining impacted soils is governed by Ca[Sb(OH) 6 ] 2 . → Citric acid extractable Sb in plants and bioavailable Sb in soils are strongly correlated. - Antimony (Sb) in soils from an active Sb mining area is highly bioavailable and controlled by the solubility of calcium antimonate.

Hole-dominated transport in InSb nanowires grown on high-quality InSb films

Science.gov (United States)

Algarni, Zaina; George, David; Singh, Abhay; Lin, Yuankun; Philipose, U.

2016-12-01

We have developed an effective strategy for synthesizing p-type indium antimonide (InSb) nanowires on a thin film of InSb grown on glass substrate. The InSb films were grown by a chemical reaction between S b 2 S 3 and I n and were characterized by structural, compositional, and optical studies. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) studies reveal that the surface of the substrate is covered with a polycrystalline InSb film comprised of sub-micron sized InSb islands. Energy dispersive X-ray (EDX) results show that the film is stoichiometric InSb. The optical constants of the InSb film, characterized using a variable-angle spectroscopic ellipsometer (VASE) shows a maximum value for refractive index at 3.7 near 1.8 eV, and the extinction coefficient (k) shows a maximum value 3.3 near 4.1 eV. InSb nanowires were subsequently grown on the InSb film with 20 nm sized Au nanoparticles functioning as the metal catalyst initiating nanowire growth. The InSb nanowires with diameters in the range of 40-60 nm exhibit good crystallinity and were found to be rich in Sb. High concentrations of anions in binary semiconductors are known to introduce acceptor levels within the band gap. This un-intentional doping of the InSb nanowire resulting in hole-dominated transport in the nanowires is demonstrated by the fabrication of a p-channel nanowire field effect transistor. The hole concentration and field effect mobility are estimated to be ≈1.3 × 1017 cm-3 and 1000 cm2 V-1 s-1, respectively, at room temperature, values that are particularly attractive for the technological implications of utilizing p-InSb nanowires in CMOS electronics.

Calcination of calcium acetate and calcium magnesium acetate: effect of the reacting atmosphere

Energy Technology Data Exchange (ETDEWEB)

Adanez, J.; Diego, L.F. de; Garcia-Labiano, F. [Instituto de Carboquimica, Zaragoza (Spain). Dept. of Energy and Environment

1999-04-01

The calcination process of the calcium acetate (CA) and calcium magnesium acetate (CMA) was investigated as a previous step for coal gas desulfurisation during sorbent injection at high temperatures because the excellent results demonstrated by these sorbents as sulfur removal agents both in combustion and gasification processes. As pore structure developed during calcination is one of the most important characteristics of the sorbent related with the later reaction with the gaseous pollutants, several calcination tests were conducted in a drop tube reactor at temperatures from 700{degree}C to 1100{degree}C, and residence times from 0.8 to 2.4 s. Four different gas atmospheres were used for comparative purposes: inert, oxidising, reducing, and non-calcining (pure CO{sub 2}). Despite the advantage of the high porous cenospheric structure developed by these sorbents during their injection at high temperature, calcination of the CaCO{sub 3} was not complete even at the longest residence time, 2.4 s, and the highest temperature, 1100{degree}C, tested. An important effect of the reacting atmosphere on the calcination conversion and on the sorbent pore structure was detected. The CO{sub 2} concentration around the particle, both that fed in the reacting gases or that generated by organic material combustion, seems to be responsible for the final calcination conversions obtained in each case, also affecting the sintering suffered by the sorbents. 19 refs., 10 figs.

New Waste Calcining Facility (NWCF) Waste Streams

International Nuclear Information System (INIS)

K. E. Archibald

1999-01-01

This report addresses the issues of conducting debris treatment in the New Waste Calcine Facility (NWCF) decontamination area and the methods currently being used to decontaminate material at the NWCF

Experimental study on the effect of calcination on the volcanic ash activity of diatomite

Science.gov (United States)

Xiao, Liguang; Pang, Bo

2017-09-01

The volcanic ash activity of diatomite was studied under the conditions of aerobic calcination and vacuum calcination by the combined water rate method, it was characterized by XRD, BET and SEM. The results showed that the volcanic ash activity of diatomite under vacuum conditions was higher than that of aerobic calcination, 600°C vacuum calcination 2h, the combined water rate of diatomite-Ca(OH)2-H2O system was increased from 6.24% to 71.43%, the volcanic ash activity reached the maximum value, the specific surface

InSb semiconductors and (In,Mn)Sb diluted magnetic semiconductors: Growth and properties

International Nuclear Information System (INIS)

Tran, Lien

2011-01-01

This dissertation describes investigations of the growth by molecular beam epitaxy and the characterization of the semiconductor InSb as well as the diluted magnetic semiconductor (DMS) In 1-x Mn x Sb. The InSb films were grown on GaAs (001) substrate and Si (001) offcut by 4 toward (110) substrate up to a thickness of about 2 μm, in spite of a large lattice mismatch between the epi-layer and substrate (14.6% between InSb and GaAs, and 19.3% between InSb and Si). After optimizing the growth conditions, the best InSb films grown directly on GaAs without any special technique results in a high crystal quality, low noise, and an electron mobility of 41100 cm 2 /V s Vs with associated electron concentration of 2.9.10 6 cm -3 at 300 K. Such structures could be used, for example, for infrared detector structures. The growth of InSb on Si, however, is a challenge. In order to successfully grow InSb on Si, tilted substrates and the insertion of buffer layers were used, which helps to reduce the lattice mismatch as well as the formation of defects, and hence to improve the crystal quality. An electron mobility of 24000 cm 2 /V s measured at 300 K, with an associated carrier concentration of 2.6.10 1 6 cm -3 is found for the best sample that was grown at 340 C with a 0.06 μm-thick GaSb/AlSb superlattice buffer layer. The smaller value of electron mobility (compared to the best GaAsbased sample) is related to a higher density of microtwins and stacking faults as well as threading dislocations in the near-interface region as shown by transmission electron microscopy. Deep level noise spectra indicate the existence of deep levels in both GaAs and Si-based samples. The samples grown on Si exhibit the lowest Hooge factor at 300 K, lower than the samples grown on GaAs. Taking the optimized growth conditions of InSb/GaAs, the diluted magnetic semiconductor In 1-x Mn x Sb/GaAs (001) is prepared by adding a few percent of Mn into the host material InSb during growth. I have

Chemistry of proposed calcination/dissolution processing of Hanford Site tank wastes

International Nuclear Information System (INIS)

Delegard, C.H.

1995-01-01

Plans exist to separate radioactive waste stored in underground tanks at the US Department of Energy's Hanford Site in south central Washington State into low-level and high-level fractions, and to immobilize the separate fractions in high-integrity vitrified forms for long-term disposal. Calcination with water dissolution has been proposed as a possible treatment for achieving low/high-level separation. Chemistry development activities conducted since 1992 with simulated and genuine tank waste show that calcination/dissolution destroys organic carbon and converts nitrate and nitrite to hydroxide and benign offgases. The process also dissolves significant quantities of bulk chemicals (aluminum, chromium, and phosphate), allowing their redistribution from the high-level to the low-level fraction. Present studies of the chemistry of calcination/dissolution processing of genuine wastes, conducted in the period October 1993 to September 1994, show the importance of sodium fluoride phosphate double salt in controlling phosphate dissolution. Peptization of waste solids is of concern if extensive washing occurs. Strongly oxidizing conditions imposed by calcination reactions were found to convert transition metals to soluble anions in the order chromate > manganate > > ferrate. In analogy with manganese behavior, plutonium dissolution, presumably by oxidation to more soluble anionic species, also occurs by calcination/dissolution. Methods to remove plutonium from the product low-level solution stream must be developed

Spray Calciner/In-Can Melter high-level waste solidification technical manual

International Nuclear Information System (INIS)

Larson, D.E.

1980-09-01

This technical manual summarizes process and equipment technology developed at Pacific Northwest Laboratory over the last 20 years for vitrification of high-level liquid waste by the Spray Calciner/In-Can Melter process. Pacific Northwest Laboratory experience includes process development and demonstration in laboratory-, pilot-, and full-scale equipment using nonradioactive synthetic wastes. Also, laboratory- and pilot-scale process demonstrations have been conducted using actual high-level radioactive wastes. In the course of process development, more than 26 tonnes of borosilicate glass have been produced in 75 canisters. Four of these canisters contained radioactive waste glass. The associated process and glass chemistry is discussed. Technology areas described include calciner feed treatment and techniques, calcination, vitrification, off-gas treatment, glass containment (the canister), and waste glass chemistry. Areas of optimization and site-specific development that would be needed to adapt this base technology for specific plant application are indicated. A conceptual Spray Calciner/In-Can Melter system design and analyses are provided in the manual to assist prospective users in evaluating the process for plant application, to provide equipment design information, and to supply information for safety analyses and environmental reports. The base (generic) technology for the Spray Calciner/In-Can Melter process has been developed to a point at which it is ready for plant application

In vitro studies evaluating leaching of mercury from mine waste calcine using simulated human body fluids

Science.gov (United States)

Gray, John E.; Plumlee, Geoffrey S.; Morman, Suzette A.; Higueras, Pablo L.; Crock, James G.; Lowers, Heather A.; Witten, Mark L.

2010-01-01

In vitro bioaccessibility (IVBA) studies were carried out on samples of mercury (Hg) mine-waste calcine (roasted Hg ore) by leaching with simulated human body fluids. The objective was to estimate potential human exposure to Hg due to inhalation of airborne calcine particulates and hand-to-mouth ingestion of Hg-bearing calcines. Mine waste calcines collected from Hg mines at Almadén, Spain, and Terlingua, Texas, contain Hg sulfide, elemental Hg, and soluble Hg compounds, which constitute primary ore or compounds formed during Hg retorting. Elevated leachate Hg concentrations were found during calcine leaching using a simulated gastric fluid (as much as 6200 μg of Hg leached/g sample). Elevated Hg concentrations were also found in calcine leachates using a simulated lung fluid (as much as 9200 μg of Hg leached/g), serum-based fluid (as much as 1600 μg of Hg leached/g), and water of pH 5 (as much as 880 μg of Hg leached/g). The leaching capacity of Hg is controlled by calcine mineralogy; thus, calcines containing soluble Hg compounds contain higher leachate Hg concentrations. Results indicate that ingestion or inhalation of Hg mine-waste calcine may lead to increased Hg concentrations in the human body, especially through the ingestion pathway.

Montmorillonite Supported Titanium/Antimony Catalyst:Preparation, Characterization and Immobilization

Institute of Scientific and Technical Information of China (English)

CHEN Guiyong; WANG Xiaoqun; ZHAO Chuan; DU Shanyi

2014-01-01

Montmorillonite supported titanium (Ti-MMT) or antimony catalyst (Sb-MMT) has been a hot area of research on preparing polyethylene terephthalate/montmorillonite (PET/MMT) nanocomposites by in situ polymerization. So removal of Ti or Sb from Ti-MMT or Sb-MMT is not expected during in situ polymerization. Studies on immobilization of Ti or Sb on Ti-MMT or Sb-MMT are seldom reported. In this work, a series of montmorillonite supported catalysts of titanium (Ti-MMT) or antimony (Sb-MMT) and co-intercalated montmorillonite of titanium and antimony (Ti/Sb-MMT) were prepared by (1) the reaction of sodium bentonite suspension with intercalating solution containing titanium tetrachloride and/or antimony chloride, and (2) drying or calcinating the products at different temperature (100, 150, 240, 350 and 450℃). The physicochemical properties of these MMT supported catalysts were studied by X-ray diffraction (XRD), fourier transform infrared spectroscopy (FT-IR), inductively coupled plasma optical emission spectrometer (ICPOES), N2 adsorption/desorption isotherms, UV-visible diffuse reflectance spectroscopy(UV-vis) and transmission electron microscopy (TEM). The immobile character of Ti or Sb on MMT supported catalysts was evaluated by a two-step method in deionized water or ethylene glycol. Several results were obtained, i e, (a) during the preparation, with an increase in drying or calcinating temperature, the amount of titanium and/or antimony species remained on these MMT supported catalysts decreased, (b) the experiments about immobile character of Ti or/and Sb showed that with an increase in drying or calcinating temperature, the immobilization of Ti and/or Sb species remained on these MMT supported catalysts increased gradually, (c) Ti-MMT calcinated at 450℃had the biggest pore volume, which means Ti-MMT had the best adsorption application prospect.

Characterization of magnetic biochar amended with silicon dioxide prepared at high temperature calcination

Directory of Open Access Journals (Sweden)

Baig Shams Ali

2016-09-01

Full Text Available Calcination is considered to increase the hardness of composite material and prevent its breakage for the effective applications in environmental remediation. In this study, magnetic biochar amended with silicon dioxide was calcined at high temperature under nitrogen environment and characterized using various techniques. X-ray diffraction (XRD analysis revealed elimination of Fe3O4 peaks under nitrogen calcination and formation of Fe3Si and iron as major constituents of magnetic biochar-SiO2 composite, which demonstrated its superparamagnetic behavior (>80 A2·kg−1 comparable to magnetic biochar. Thermogravimetric analysis (TGA revealed that both calcined samples generated higher residual mass (>96 % and demonstrated better thermal stability. The presence of various bands in Fourier transform infrared spectroscopy (FT-IR was more obvious and the elimination of H–O–H bonding was observed at high temperature calcination. In addition, scanning electron microscopy (SEM images revealed certain morphological variation among the samples and the presence of more prominent internal and external pores, which then judged the surface area and pore volume of samples. Findings from this study suggests that the selective calcination process could cause useful changes in the material composites and can be effectively employed in environmental remediation measures.

The effect of calcination conditions on the graphitizability of novel synthetic and coal-derived cokes

Science.gov (United States)

Bennett, Barbara Ellen

The effects of calcination heating rate and ultimate calcination temperature upon calcined coke and subsequent graphitic material microstructures were studied for materials prepared from three different precursors. The pitch precursors used were Mitsubishi AR pitch (a synthetic, 100% mesophase pitch), the NMP-extracted portion of a raw coal, and the NMP-extracted fraction of a coal liquefaction residue obtained from an HTI pilot plant. These materials were all green-coked under identical conditions. Optical microscopy confirmed that the Mitsubishi coke was very anisotropic and the HTI coke was nearly as anisotropic. The coke produced from the direct coal extract was very isotropic. Crystalline development during calcination heating was verified by high-temperature x-ray diffraction. Experiments were performed to ascertain the effects of varying calcination heating rate and ultimate temperature. It was determined that calcined coke crystallite size increased with increasing temperature for all three materials but was found to be independent of heating rate. The graphene interplanar spacing decreased with increasing temperature for the isotropic NMP-extract material but increased with increasing temperature for the anisotropic materials---Mitsubishi and HTI cokes. Graphene interplanar spacing was also found to be independent of heating rate. Calcined coke real densities were, likewise, found to be independent of heating rate. The anisotropic cokes (Mitsubishi and HTI) exhibited increasing real density with increasing calcination temperature. The NMP-extract coke increased in density up to 1050°C and then suffered a dramatic reduction in real density when heated to 1250°C. This is indicative of puffing. Since there was no corresponding disruption in the crystalline structure, the puffing phenomena was determined to be intercrystalline rather than intracrystalline. After the calcined cokes were graphitized (under identical conditions), the microstructures were re

Formulation Efforts for Direct Vitrification of INEEL Blend Calcine Waste Simulate: Fiscal Year 2000

Energy Technology Data Exchange (ETDEWEB)

Crum, Jarrod V.; Vienna, John D.; Peeler, David K.; Reamer, I. A.

2001-03-30

This report documents the results of glass formulation efforts for Idaho National Engineering and Environmental Laboratory (INEEL) high level waste (HWL) calcine. Two waste compositions were used during testing. Testing started by using the Run 78 calcine composition and switched to simulated Blend calcine composition when it became available. The goal of the glass formulation efforts was to develop a frit composition that will accept higher waste loading that satisfies the glass processing and product acceptance constraints. 1. Melting temperature of 1125 ? 25?C 2. Viscosity between 2 and 10 Pa?s at the melting temperature 3. Liquidus temperature at least 100?C below the melting temperature 4. Normalized release of B, Li and Na each below 1 g/m2 (per ASTM C 1285-97) Glass formulation efforts tested several frit compositions with variable waste loadings of Run 78 calcine waste simulant. Frit 107 was selected as the primary candidate for processing since it met all process and performance criteria up to 45 mass% waste loading. When the simulated Blend calcine waste composition became available Frits 107 and 108 compositions were retested and again Frit 107 remained the primary candidate. However, both frits suffered a decrease in waste loading when switching from the Run 78 calcine to simulated Blend calcine waste composition. This was due to increase concentrations of both F and Al2O3 along with a decrease in CaO and Na2O in the simulate Blend calcine waste all of which have strong impacts on the glass properties that limit waste loading of this type of waste.

Syntheses, and crystal and electronic structures of the new Zintl phases Na2ACdSb2 and K2ACdSb2 (A=Ca, Sr, Ba, Eu, Yb): Structural relationship with Yb2CdSb2 and the solid solutions Sr2-xAxCdSb2, Ba2-xAxCdSb2 and Eu2-xYbxCdSb2

International Nuclear Information System (INIS)

Saparov, Bayrammurad; Saito, Maia; Bobev, Svilen

2011-01-01

Presented are the details of the syntheses, crystal and electronic structures of a new family of Zintl phases Na 2 ACdSb 2 and K 2 ACdSb 2 (A=Ca, Sr, Ba, Eu, Yb), as well as the solid solutions Sr 2-x A x CdSb 2 , Ba 2-x A x CdSb 2 and Eu 2-x Yb x CdSb 2 . The structures of Na 2 ACdSb 2 and K 2 ACdSb 2 (A=Ca, Sr, Ba, Eu, Yb) were determined to be of a new type with the non-centrosymmetric space group Pmc2 1 (no. 26), Pearson symbol oP12, with lattice parameters a=4.684(1)-4.788(1) A; b=9.099(3)-9.117(2) A; c=7.837(1)-8.057(2) A for the Na 2 ACdSb 2 series, and a=4.6637(9)-5.0368(8) A; b=9.100(2)-9.8183(15) A; and c=7.7954(15)-8.4924(13) A for K 2 ACdSb 2 , respectively. The solid solutions Sr 2-x A x CdSb 2 , Ba 2-x A x CdSb 2 and Eu 2-x Yb x CdSb 2 (x∼1) are isostructural and isoelectronic to the recently reported Yb 2 CdSb 2 (space group Cmc2 1 (no. 36), Pearson symbol cP20). All discussed structures are based upon CdSb 2 4- polyanionic layers, similar to the ones observed in Yb 2 CdSb 2 , with various alkali- and/or alkaline-earth cations coordinated to them. Magnetic susceptibility and Seebeck coefficient measurements on selected Eu 2-x Yb x CdSb 2 samples, taken at low temperatures up to 300 K, are also reported. -- Graphical abstract: The quaternary Zintl phases Na 2 ACdSb 2 and K 2 ACdSb 2 (A=Ca, Sr, Ba, Eu, Yb) with novel layered structures have been synthesized for the first time and structurally characterized by single-crystal X-ray diffraction. Reported as well are the results from crystallographic and property studies of the closely related solid solutions Sr 2-x A x CdSb 2 , Ba 2-x A x CdSb 2 (x∼1), and Eu 2-x Yb x CdSb 2 (1 2 ACdSb 2 and K 2 ACdSb 2 (A=Ca, Sr, Ba, Eu, Yb) are new quaternary Zintl phases. → Sr 2-x A x CdSb 2 , Ba 2-x A x CdSb 2 (x∼1), and Eu 2-x Yb x CdSb 2 (1 4 tetrahedra. → Eu 2-x Yb x CdSb 2 (1< x<2) exhibit high Seebeck coefficient (217 μV/K at RT).

Crystallographic study of the intermediate compounds SbZn, Sb3Zn4 and Sb2Zn3

International Nuclear Information System (INIS)

Adjadj, Fouzia; Belbacha, El-djemai; Bouharkat, Malek; Kerboub, Abdellah

2006-01-01

The processes of development of semiconductor ceramics made up of bismuth, antimony and zinc often require during their preparation to know the nature of the involved phases. For that, it is always essential to refer to the diagrams of balance between phases of the binary systems or ternary. We presented in this work the study by X-rays diffraction relating to the intermediate compounds SbZn, Sb 3 Zn 4 and Sb 2 Zn 3 . The analysis by X-rays is often useful to give supplement the results of the other experimental methods

Techniques for detection of transition phases in calcined alumina

International Nuclear Information System (INIS)

Pandolfelli, V.C.; Folgueras-Dominguez, S.

1987-01-01

Detection of transition phases in alumina, is very important in the receiving control and calcination of aluminium hydroxide. The non alfa or transition phases difficults the processability and causes localized shrinkage on sintering compromising the dimensional and mechanical aspects of the product. In this research using refraction index, absorption of dyes, specific density, X-ray diffraction and scanning electron microscopy, analyses, are done in calcined hydroxides submited to different thermal treatments. The limits and facilities of each technique are discussed and compared. (Author) [pt

Sb-related defects in Sb-doped ZnO thin film grown by pulsed laser deposition

Science.gov (United States)

Luo, Caiqin; Ho, Lok-Ping; Azad, Fahad; Anwand, Wolfgang; Butterling, Maik; Wagner, Andreas; Kuznetsov, Andrej; Zhu, Hai; Su, Shichen; Ling, Francis Chi-Chung

2018-04-01

Sb-doped ZnO films were fabricated on c-plane sapphire using the pulsed laser deposition method and characterized by Hall effect measurement, X-ray photoelectron spectroscopy, X-ray diffraction, photoluminescence, and positron annihilation spectroscopy. Systematic studies on the growth conditions with different Sb composition, oxygen pressure, and post-growth annealing were conducted. If the Sb doping concentration is lower than the threshold ˜8 × 1020 cm-3, the as-grown films grown with an appropriate oxygen pressure could be n˜4 × 1020 cm-3. The shallow donor was attributed to the SbZn related defect. Annealing these samples led to the formation of the SbZn-2VZn shallow acceptor which subsequently compensated for the free carrier. For samples with Sb concentration exceeding the threshold, the yielded as-grown samples were highly resistive. X-ray diffraction results showed that the Sb dopant occupied the O site rather than the Zn site as the Sb doping exceeded the threshold, whereas the SbO related deep acceptor was responsible for the high resistivity of the samples.

Phase diagram of the Sb-Se-I system and thermodynamic properties of SbSeI

International Nuclear Information System (INIS)

Aliev, Z.S.; Musaeva, S.S.; Babanly, D.M.; Shevelkov, A.V.; Babanly, M.B.

2010-01-01

The Sb-Se-I system was investigated by using the DTA and XRD analyses and EMF measurements with an antimony electrode. The T-x diagram of the binary Sb-I system was accurately redefined. A number of polythermal sections and the projection of the liquidus surface were constructed. The fields of the primary crystallization, as well as the types and coordinates of non- and monovariant equilibria were determined. It is shown that the quasi-binary sections Sb 2 Se 3 -SbI 3 , Sb-SbSeI, SbI 3 -Se, and SbSeI-Se triangulate the Sb-Se-I system, leading to five independent subsystems. A broad area of immiscibility, that overlaps a certain part of the antimony primary crystallization field, was found. From the EMF measurements, the partial molar functions of antimony (ΔG-bar, ΔH-bar, ΔS-bar) as well as standard integral thermodynamic functions of SbSeI were calculated. The latter were found to have the following values: ΔG f,298 0 =-80.12±1.81kJ/mol; ΔH f,298 0 =-77.3±1.8kJ/mol; S 298 0 =155.2±9.5J/(molK).

Phase diagram of the Sb-Se-I system and thermodynamic properties of SbSeI

Energy Technology Data Exchange (ETDEWEB)

Aliev, Z S; Musaeva, S S; Babanly, D M [Baku State University, General and Inorganic Chemistry Department (Azerbaijan); Shevelkov, A.V., E-mail: shev@inorg.chem.msu.r [Moscow Lomonosov State University, Chemistry Department (Russian Federation); Babanly, M.B., E-mail: Babanly_mb@rambler.r [Baku State University, General and Inorganic Chemistry Department (Azerbaijan)

2010-09-03

The Sb-Se-I system was investigated by using the DTA and XRD analyses and EMF measurements with an antimony electrode. The T-x diagram of the binary Sb-I system was accurately redefined. A number of polythermal sections and the projection of the liquidus surface were constructed. The fields of the primary crystallization, as well as the types and coordinates of non- and monovariant equilibria were determined. It is shown that the quasi-binary sections Sb{sub 2}Se{sub 3}-SbI{sub 3}, Sb-SbSeI, SbI{sub 3}-Se, and SbSeI-Se triangulate the Sb-Se-I system, leading to five independent subsystems. A broad area of immiscibility, that overlaps a certain part of the antimony primary crystallization field, was found. From the EMF measurements, the partial molar functions of antimony ({Delta}G-bar, {Delta}H-bar, {Delta}S-bar) as well as standard integral thermodynamic functions of SbSeI were calculated. The latter were found to have the following values: {Delta}G{sub f,298}{sup 0}=-80.12{+-}1.81kJ/mol; {Delta}H{sub f,298}{sup 0}=-77.3{+-}1.8kJ/mol; S{sub 298}{sup 0}=155.2{+-}9.5J/(molK).

Removal of Sb(III and Sb(V by Ferric Chloride Coagulation: Implications of Fe Solubility

Directory of Open Access Journals (Sweden)

Muhammad Ali Inam

2018-04-01

Full Text Available Coagulation and precipitation appear to be the most efficient and economical methods for the removal of antimony from aqueous solution. In this study, antimony removal from synthetic water and Fe solubility with ferric chloride (FC coagulation has been investigated. The effects of pH, FC dosage, initial antimony loading and mixed Sb(III, Sb(V proportions on Fe solubility and antimony removal were studied. The results showed that the Sb(III removal efficiency increased with the increase of solution pH particularly due to an increase in Fe precipitation. The Sb(V removal was influenced by the solution pH due to a change in Fe solubility. However, the Fe solubility was only impaired by the Sb(III species at optimum pH 7. The removal efficiencies of both Sb species were enhanced with an increase in FC dose. The quantitative analysis of the isotherm study revealed the strong adsorption potential of Sb(III on Fe precipitates as compared to Sb(V. Furthermore, the removal behavior of antimony was inhibited in mixed proportion with high Sb(V fraction. In conclusion, this study contributes to better understanding the fate of Sb species, their mobilities, and comparative removal behavior, with implications for Fe solubility using ferric chloride in different aqueous environments.

Pyrochemical treatment of Idaho Chemical Processing Plant high-level waste calcine

International Nuclear Information System (INIS)

Todd, T.A.; DelDebbio, J.A.; Nelson, L.O.; Sharpsten, M.R.

1993-01-01

The Idaho Chemical Processing Plant (ICPP), located at the Idaho National Engineering Laboratory (INEL), has reprocessed irradiated nuclear fuels for the US Department of Energy (DOE) since 1951 to recover uranium, krypton-85, and isolated fission products for interim treatment and immobilization. The acidic radioactive high-level liquid waste (HLLW) is routinely stored in stainless steel tanks and then, since 1963, calcined to form a dry granular solid. The resulting high-level waste (HLW) calcine is stored in seismically hardened stainless steel bins that are housed in underground concrete vaults. A research and development program has been established to determine the feasibility of treating ICPP HLW calcine using pyrochemical technology.This technology is described

46 CFR 148.04-17 - Petroleum coke, calcined, at 130 °F or above.

Science.gov (United States)

2010-10-01

... 46 Shipping 5 2010-10-01 2010-10-01 false Petroleum coke, calcined, at 130 °F or above. 148.04-17...-17 Petroleum coke, calcined, at 130 °F or above. (a) The requirements of this part do not apply to bulk shipments of petroleum coke, calcined, on any vessel when the material is less than 130 °F. (b...

Effect of InSb/In0.9Al0.1Sb superlattice buffer layer on the structural and electronic properties of InSb films

Science.gov (United States)

Zhao, Xiaomeng; Zhang, Yang; Guan, Min; Cui, Lijie; Wang, Baoqiang; Zhu, Zhanping; Zeng, Yiping

2017-07-01

The effect of InSb/In0.9Al0.1Sb buffer layers on InSb thin films grown on GaAs (0 0 1) substrate by molecular beam epitaxy (MBE) is investigated. The crystal quality and the surface morphology of InSb are characterized by XRD and AFM. The carrier transport property is researched through variable temperature hall test. The sharp interface between InSb/In0.9Al0.1Sb is demonstrated important for the high quality InSb thin film. We try different superlattice buffer layers by changing ratios, 2-0.5, thickness, 300-450 nm, and periods, 20-50. According to the function of the dislocation density to the absolute temperature below 150 K with different periods of SL buffers, we can find that the number of periods of superlattice is a major factor to decrease the density of threading dislocations. With the 50 periods SL buffer layer, the electron mobility of InSb at the room temperature and liquid nitrogen cooling temperature is ∼63,000 and ∼4600 cm2/V s, respectively. We deduce that the interface in the SL structure works as a filter layer to prevent the dislocation propagating to the upper InSb thin films.

Calcination effects on CeZrOx geometry and styrene production from ethylbenzene

NARCIS (Netherlands)

Kovacevic, M.; Brunet Espinosa, Roger; Lefferts, Leonardus; Mojet, Barbara

2014-01-01

A series of CeZrOx catalysts was prepared by calcination of hydrothermally obtained metal oxide precipitate at increasing temperatures. The samples were characterized by HRSEM, XRD and Raman spectroscopy, showing a change in morphology and particle size as a function of calcination temperature.

Final safety-analysis report for the Fifth Calcined Solids Storage Facility

International Nuclear Information System (INIS)

1982-01-01

Radioactive aqueous wastes generated by the solvent extraction of uranium from expended fuels at ICPP will be calcined in the New Waste Calcining Facility (NWCF). The calcined solids are pneumatically transferred to stainless steel bins enclosed in concrete vaults for interim storage of up to 500 years. The Fifth Calcined Solids Storage Facility (CSSF) provides 1000 m 3 of storage and consists of seven annular stainless steel bins inside a reinforced concrete vault set on bedrock. Storage of calcined solids is essentially a passive operation with very little opportunity for release of radionuclides and with no potential for criticality. There will be no potential for fire or explosion. Shielding has been designed to assure that the radiation levels at the vault exterior surfaces will be limited to less than 0.5 mRem/h. A sump in the vault floor will collect any in-leakage that may occur. Any water that collects in the sump will be sampled then removed with the sump jet. There will be an extremely small chance of release of radioactive particulates into the atmosphere as a result of a bin leak. The Design Basis Accident (DBA) postulates the spill of solids from an eroded fill line into the vault coupled with a failure of the vault cooling air radiation monitor. For the DBA, the maximum calculated radiation dose to an exposed individual near the site boundary is less than 1.2 μRem to the bone and lung

Preparation of plutonium waste forms with ICPP calcined high-level waste

Energy Technology Data Exchange (ETDEWEB)

Staples, B.A.; Knecht, D.A. [Lockheed Idaho Technologies Co., Idaho Falls, ID (United States); O`Holleran, T.P. [Argonne National Lab.-West, Idaho Falls, ID (United States)] [and others

1997-05-01

Glass and glass-ceramic forms developed for the immobilization of calcined high-level wastes generated by Idaho Chemical Processing Plant (ICPP) fuel reprocessing activities have been investigated for ability to immobilize plutonium and to simultaneously incorporate calcined waste as an anti-proliferation barrier. Within the forms investigated, crystallization of host phases result in an increased loading of plutonium as well as its incorporation into potentially more durable phases than the glass. The host phases were initially formed and characterized with cerium (Ce{sup +4}) as a surrogate for plutonium (Pu{sup +4}) and samarium as a neutron absorber for criticality control. Verification of the surrogate testing results were then performed replacing cerium with plutonium. All testing was performed with surrogate calcined high-level waste. The results of these tests indicated that a potentially useful host phase, based on zirconia, can be formed either by devitrification or solid state reaction in the glass studied. This phase incorporates plutonium as well as samarium and the calcined waste becomes part of the matrix. Its ease of formation makes it potentially useful in excess plutonium dispositioning. Other durable host phases for plutonium and samarium, including zirconolite and zircon have been formed from zirconia or alumina calcine through cold press-sintering techniques and hot isostatic pressing. Host phase formation experiments conducted through vitrification or by cold press-sintering techniques are described and the results discussed. Recommendations are given for future work that extends the results of this study.

Preparation of plutonium waste forms with ICPP calcined high-level waste

International Nuclear Information System (INIS)

Staples, B.A.; Knecht, D.A.; O'Holleran, T.P.

1997-05-01

Glass and glass-ceramic forms developed for the immobilization of calcined high-level wastes generated by Idaho Chemical Processing Plant (ICPP) fuel reprocessing activities have been investigated for ability to immobilize plutonium and to simultaneously incorporate calcined waste as an anti-proliferation barrier. Within the forms investigated, crystallization of host phases result in an increased loading of plutonium as well as its incorporation into potentially more durable phases than the glass. The host phases were initially formed and characterized with cerium (Ce +4 ) as a surrogate for plutonium (Pu +4 ) and samarium as a neutron absorber for criticality control. Verification of the surrogate testing results were then performed replacing cerium with plutonium. All testing was performed with surrogate calcined high-level waste. The results of these tests indicated that a potentially useful host phase, based on zirconia, can be formed either by devitrification or solid state reaction in the glass studied. This phase incorporates plutonium as well as samarium and the calcined waste becomes part of the matrix. Its ease of formation makes it potentially useful in excess plutonium dispositioning. Other durable host phases for plutonium and samarium, including zirconolite and zircon have been formed from zirconia or alumina calcine through cold press-sintering techniques and hot isostatic pressing. Host phase formation experiments conducted through vitrification or by cold press-sintering techniques are described and the results discussed. Recommendations are given for future work that extends the results of this study

CFD Modelling and Experimental Testing of Thermal Calcination of Kaolinite Rich Clay Particles - An Effort towards Green Concrete

DEFF Research Database (Denmark)

Gebremariam, Abraham Teklay

Cement industry is one of the major industrial emitters of greenhouse gases, generating 5-7% of the total anthropogenic CO2 emissions. Consequently, use of supplementary cementitious materials (SCM) to replace part of the CO2-intensive cement clinker is an attractive way to mitigate CO2 emissions...... from cement industry. SCMs based on industrial byproducts like fly ashes and slags are subject to availability problems. Yet clays are the most ubiquitous material on earth's crust. Thus, properly calcined clays are a very promising candidate for SCMs to produce green cements. Calcination...... property of the calcined clay material, among which is the density of calcines. By using the variation in density of calcines, an optimum residence time has been marked. At this time the calcines display a minimum density that corresponds to the most dehydroxylated calcines. The behavior of flash calcined...

Effect of calcination temperature on microstructure and electrochemical performance of lithium-rich layered oxide cathode materials

International Nuclear Information System (INIS)

Ma, Quanxin; Peng, Fangwei; Li, Ruhong; Yin, Shibo; Dai, Changsong

2016-01-01

Highlights: • A series of Li-rich layered oxide cathode materials (Li_1_._2Mn_0_._5_6Ni_0_._1_6Co_0_._0_8O_2) were successfully synthesized via a two-step synthesis method. • The effects of calcination temperature on the cathode materials were researched in detail. • A well-crystallized layered structure was obtained as the calcination temperature increased. • The samples calcined in a range of 850–900 °C exhibited excellent electrochemical performance. - Abstract: Lithium-rich layered oxide cathode materials (Li_1_._2Mn_0_._5_6Ni_0_._1_6Co_0_._0_8O_2 (LLMO)) were synthesized via a two-step synthesis method involving co-precipitation and high-temperature calcination. The effects of calcination temperature on the cathode materials were studied in detail. Structural and morphological characterizations revealed that a well-crystallized layered structure was obtained at a higher calcination temperature. Electrochemical performance evaluation revealed that a cathode material obtained at a calcination temperature of 850 °C delivered a high initial discharge capacity of 266.8 mAh g"−"1 at a 0.1 C rate and a capacity retention rate of 95.8% after 100 cycles as well as excellent rate capability. Another sample calcinated at 900 °C exhibited good cycling stability. It is concluded that the structural stability and electrochemical performance of Li-rich layered oxide cathode materials were strongly dependent on calcination temperatures. The results suggest that a calcination temperature in a range of 850–900 °C could promote electrochemical performance of this type of cathode materials.

Effect of calcination temperature on microstructure and electrochemical performance of lithium-rich layered oxide cathode materials

Energy Technology Data Exchange (ETDEWEB)

Ma, Quanxin; Peng, Fangwei; Li, Ruhong; Yin, Shibo; Dai, Changsong, E-mail: changsd@hit.edu.cn

2016-11-15

Highlights: • A series of Li-rich layered oxide cathode materials (Li{sub 1.2}Mn{sub 0.56}Ni{sub 0.16}Co{sub 0.08}O{sub 2}) were successfully synthesized via a two-step synthesis method. • The effects of calcination temperature on the cathode materials were researched in detail. • A well-crystallized layered structure was obtained as the calcination temperature increased. • The samples calcined in a range of 850–900 °C exhibited excellent electrochemical performance. - Abstract: Lithium-rich layered oxide cathode materials (Li{sub 1.2}Mn{sub 0.56}Ni{sub 0.16}Co{sub 0.08}O{sub 2} (LLMO)) were synthesized via a two-step synthesis method involving co-precipitation and high-temperature calcination. The effects of calcination temperature on the cathode materials were studied in detail. Structural and morphological characterizations revealed that a well-crystallized layered structure was obtained at a higher calcination temperature. Electrochemical performance evaluation revealed that a cathode material obtained at a calcination temperature of 850 °C delivered a high initial discharge capacity of 266.8 mAh g{sup −1} at a 0.1 C rate and a capacity retention rate of 95.8% after 100 cycles as well as excellent rate capability. Another sample calcinated at 900 °C exhibited good cycling stability. It is concluded that the structural stability and electrochemical performance of Li-rich layered oxide cathode materials were strongly dependent on calcination temperatures. The results suggest that a calcination temperature in a range of 850–900 °C could promote electrochemical performance of this type of cathode materials.

Pyrochemical separation of radioactive components from inert materials in ICPP high-level calcined waste

International Nuclear Information System (INIS)

Del Debbio, J.A.; Nelson, L.O.; Todd, T.A.

1995-05-01

Since 1963, calcination of aqueous wastes from reprocessing of DOE-owned spent nuclear fuels has resulted in the accumulation of approximately 3800 m 3 of high-level waste (HLW) at the Idaho Chemical Processing Plant (ICPP). The waste is in the form of a granular solid called calcine and is stored on site in stainless steel bins which are encased in concrete. Due to the leachability of 137 Cs and 90 Sr and possibly other radioactive components, the calcine is not suitable for final disposal. Hence, a process to immobilize calcine in glass is being developed. Since radioactive components represent less than 1 wt % of the calcine, separation of actinides and fission products from inert components is being considered to reduce the volume of HLW requiring final disposal. Current estimates indicate that compared to direct vitrification, a volume reduction factor of 10 could result in significant cost savings. Aqueous processes, which involve calcine dissolution in nitric acid followed by separation of actinide and fission products by solvent extraction and ion exchange methods, are being developed. Pyrochemical separation methods, which generate small volumes of aqueous wastes and do not require calcine dissolution, have been evaluated as alternatives to aqueous processes. This report describes three proposed pyrochemical flowsheets and presents the results of experimental studies conducted to evaluate their feasibility. The information presented is a consolidation of three reports, which should be consulted for experimental details

Fluidized-bed calcination of LWR fuel-reprocessing HLLW: requirements and potential for off-gas cleanup

International Nuclear Information System (INIS)

Schindler, R.E.

1979-01-01

Fluidized-bed solidification (calcination) was developed on a pilot scale for a variety of simulated LWR high-level liquid-waste (HLLW) and blended high-level and intermediate-level liquid-waste (ILLW) compositions. It has also been demonstrated with ICPP fuel-reprocessing waste since 1963 in the Waste Calcining Facility (WCF) at gross feed rates of 5 to 12 m 3 /day. A fluidized-bed calciner produces a relatively large volume of off-gas. A calciner solidifying 6 m 3 /day of liquid waste would generate about 13 standard m 3 /min of off-gas containing 10 to 20 g of entrained solids per standard m 3 of off-gas. Use of an off-gas system similar to that of the WCF could provide an overall process decontamination factor for particulates of about 2 x 10 10 . A potential advantage of fluidized-bed calcination over other solidification methods is the ability to control ruthenium volatilization from the calciner at less than 0.01% by calcining at 500 0 C or above. Use of an off-gas system similar to that of the WCF would provide an overall process decontamination factor for volatile ruthenium of greater than 1.6 x 10 7

Quantitative analysis of calcined fertilizers by X-ray diffraction patterns

International Nuclear Information System (INIS)

Cekinski, E.

1987-01-01

An X-ray diffraction pattern method for quantitative analyses of phosphate fertilizers obtained by calcination of a misture of Anitapolis phosphate concentrate and sodium carbonate is described. The method consists in plotting a calibration curve, using spinel (MgAl 2 O 4 ) as internal standard, of the phases that were formed by calcination, sintetized in laboratory. The tests conducted in order to avail the method accuracy showed good correlation between the obtained data and the real values. (author) [pt

Total oxidation of toluene over calcined trimetallic hydrotalcites type catalysts

Energy Technology Data Exchange (ETDEWEB)

Palacio, Luz A. [Instituto Superior Tecnico, IBB - Centro de Engenharia Biologica e Quimica, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Grupo Catalizadores y Adsorbentes, Universidad de Antioquia 1-317, A.A. 1226 Medellin (Colombia); Velasquez, Juliana; Echavarria, Adriana [Grupo Catalizadores y Adsorbentes, Universidad de Antioquia 1-317, A.A. 1226 Medellin (Colombia); Faro, Arnaldo [Departamento de Fisicoquimica, Instituto de Quimica, Universidade Federal do Rio de Janeiro, Ilha do Fundao, CT bloco A, Rio de Janeiro (Brazil); Ramoa Ribeiro, F. [Instituto Superior Tecnico, IBB - Centro de Engenharia Biologica e Quimica, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal); Ribeiro, M. Filipa, E-mail: filipa.ribeiro@ist.utl.pt [Instituto Superior Tecnico, IBB - Centro de Engenharia Biologica e Quimica, Universidade Tecnica de Lisboa, Av. Rovisco Pais, 1049-001 Lisboa (Portugal)

2010-05-15

Two trimetallic ZnCuAl and MnCuAl hydrotalcites have been successfully synthesized by a co-precipitation method. The manganese based material was identified as a new hydrotalcite phase. Both lamellar precursors were calcined at 450 and 600 deg. C and the resulting catalysts were tested on reaction of total oxidation of toluene. The solids were characterized by X-ray diffraction, thermal analysis, atomic absorption spectroscopy, Fourier transformed infrared spectroscopy, N{sub 2} adsorption and H{sub 2} temperature-programmed reduction. It was found that ZnCuAl materials are composed of copper and zinc oxides supported on alumina; while MnCuAl ones comprise basically spinel phases, which were not completely identified. The catalytic behavior of the calcined samples showed that Mn hydrotalcite calcined at 450 deg. C exhibited the best catalytic performance that corresponds to 100% toluene conversion into CO{sub 2} at about 300 deg. C.

Total oxidation of toluene over calcined trimetallic hydrotalcites type catalysts

International Nuclear Information System (INIS)

Palacio, Luz A.; Velasquez, Juliana; Echavarria, Adriana; Faro, Arnaldo; Ramoa Ribeiro, F.; Ribeiro, M. Filipa

2010-01-01

Two trimetallic ZnCuAl and MnCuAl hydrotalcites have been successfully synthesized by a co-precipitation method. The manganese based material was identified as a new hydrotalcite phase. Both lamellar precursors were calcined at 450 and 600 deg. C and the resulting catalysts were tested on reaction of total oxidation of toluene. The solids were characterized by X-ray diffraction, thermal analysis, atomic absorption spectroscopy, Fourier transformed infrared spectroscopy, N 2 adsorption and H 2 temperature-programmed reduction. It was found that ZnCuAl materials are composed of copper and zinc oxides supported on alumina; while MnCuAl ones comprise basically spinel phases, which were not completely identified. The catalytic behavior of the calcined samples showed that Mn hydrotalcite calcined at 450 deg. C exhibited the best catalytic performance that corresponds to 100% toluene conversion into CO 2 at about 300 deg. C.

Near-surface depletion of antimony during the growth of GaAsSb and GaAs/GaAsSb nanowires

Energy Technology Data Exchange (ETDEWEB)

Kauko, H.; Helvoort, A. T. J. van, E-mail: a.helvoort@ntnu.no [Department of Physics, Norwegian University of Science and Technology (NTNU), Trondheim (Norway); Fimland, B. O.; Munshi, A. M. [Department of Electronics and Telecommunications, NTNU, Trondheim (Norway); Grieb, T.; Müller, K.; Rosenauer, A. [Institut für Festkörperphysik, Universität Bremen, Bremen (Germany)

2014-10-14

The near-surface reduction of the Sb mole fraction during the growth of GaAsSb nanowires (NWs) and GaAs NWs with GaAsSb inserts has been studied using quantitative high-angle annular dark field scanning transmission electron microscopy (STEM). A model for diffusion of Sb in the hexagonal NWs was developed and employed in combination with the quantitative STEM analysis. GaAsSb NWs grown by Ga-assisted molecular beam epitaxy (MBE) and GaAs/GaAsSb NWs grown by Ga- and Au-assisted MBE were investigated. At the high temperatures employed in the NW growth, As-Sb exchange at and outward diffusion of Sb towards the surface take place, resulting in reduction of the Sb concentration at and near the surface in the GaAsSb NWs and the GaAsSb inserts. In GaAsSb NWs, an increasing near-surface depletion of Sb was observed towards the bottom of the NW due to longer exposure to the As beam flux. In GaAsSb inserts, an increasing change in the Sb concentration profile was observed with increasing post-insert axial GaAs growth time, resulting from a combined effect of radial GaAs overgrowth and diffusion of Sb. The effect of growth temperature on the diffusion of Sb in the GaAsSb inserts was identified. The consequences of these findings for growth optimization and the optoelectronic properties of GaAsSb are discussed.

Synthesis of type A zeolite from calcinated kaolin

International Nuclear Information System (INIS)

Rodrigues, E.C.; Neves, R.F.; Souza, J.A.S.; Moraes, C.G.; Macedo, E.N.

2011-01-01

The mineral production has caused great concern in environmental and industrial scenario due to the effects caused to the environment. The industries of processing kaolin for paper are important economically for the state of Para, but produce huge quantities of tailings, which depend on large areas to be stocked. This material is rich in silico-aluminates can be recycled and used as raw material for other industries. The objective is to synthesize zeolite A at different temperatures of calcination and synthesis. The starting materials and synthesis of zeolite A have been identified and characterized through analysis of X-ray diffraction (DRX) and scanning electron microscopy (MEV). The synthesis process of zeolite A, using as source of silica and the aluminum metakaolin, which was calcined at temperatures of 700 ° C and 800 ° C for 2 hours of landing in a burning furnace type muffle. Observed in relation to the calcination of kaolin as the main phase, the metakaolin. This is just a removal of water from its structure, so we opted for the lower temperature, less energy consumption. The synthesis process of zeolite A, produced good results for the formation of zeolites type A, which were characterized with high purities. (author)

Biodiesel production from waste cooking oil using calcined scallop shell as catalyst

International Nuclear Information System (INIS)

Sirisomboonchai, Suchada; Abuduwayiti, Maidinamu; Guan, Guoqing; Samart, Chanatip; Abliz, Shawket; Hao, Xiaogang; Kusakabe, Katsuki; Abudula, Abuliti

2015-01-01

Highlights: • Calcined scallop shell was used as low-cost and effective catalyst for biodiesel production. • BDF yield from waste cooking oil reached 86% at 65 °C with a catalyst loading amount of 5 wt%. • Calcined scallop shell showed good reusability. • Calcium glyceroxide played an important role on the reusability of calcined scallop shell. • Water in the waste cooking oil had negative effect on the catalytic activity of calcined scallop shell. - Abstract: Transesterification of waste cooking oil (WCO) and methanol by using calcined scallop shell (CSS) as catalyst was carried out in a closed system for biodiesel fuel (BDF) production. It is found that the optimum calcination temperature for the preparation of CSS was 1000 °C. The effects of transesterification temperature, reaction time, methanol/oil molar ratio and catalyst loading amount on the BDF yield were investigated. Compared with the commercial CaO, CSS showed higher catalytic activity and the BDF yield reached 86% at 65 °C with a catalyst loading amount of 5 wt% (WCO basis) and a reaction time of 2 h. The catalyst was reused for 5 cycles whilst the BDF yield decreased 23%. It is found that CaO in CSS was transferred to calcium glyceroxide after the transesterification reaction, and calcium glyceroxide also showed good catalytic activity and reusability. Furthermore, Water content in WCO had negative effect on BDF yield. It is found that BDF yield reduced 15% due to the occurring of saponification when the water content was increased from 0.64% to 2.48%. It is expected that CCS can be used as an alternative and cheap catalyst for the biodiesel production

CO{sub 2} capture behavior of shell during calcination/carbonation cycles

Energy Technology Data Exchange (ETDEWEB)

Li, Y.J.; Zhao, C.S.; Chen, H.C.; Duan, L.B.; Chen, X.P. [School of Energy and Environment, Southeast University, Nanjing (China)

2009-08-15

The cyclic carbonation performances of shells as CO{sub 2} sorbents were investigated during multiple calcination/carbonation cycles. The carbonation kinetics of the shell and limestone are similar since they both exhibit a fast kinetically controlled reaction regime and a diffusion controlled reaction regime, but their carbonation rates differ between these two regions. Shell achieves the maximum carbonation conversion for carbonation at 680-700 C. The mactra veneriformis shell and mussel shell exhibit higher carbonation conversions than limestone after several cycles at the same reaction conditions. The carbonation conversion of scallop shell is slightly higher than that of limestone after a series of cycles. The calcined shell appears more porous than calcined limestone, and possesses more pores >230 nm, which allow large CO{sub 2} diffusion-carbonation reaction rates and higher conversion due to the increased surface area of the shell. The pores of the shell that are greater than 230 nm do not sinter significantly. The shell has more sodium ions than limestone, which probably leads to an improvement in the cyclic carbonation performance during the multiple calcination/carbonation cycles. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

The equilibrium diagram and some properties of alloys Gd5Sb3-Tb5Sb3 system

International Nuclear Information System (INIS)

Azizov, Yu.S.; Abulkhaev, V.D.; Ganiev, I.N.

2001-01-01

The purpose of present work is investigation equilibrium diagram of Gd 5 Sb 3 -Tb 5 Sb 3 system in total range of concentrations. Equilibrium diagram of Gd 5 Sb 3 -Tb 5 Sb 3 system investigated by methods of difference-thermal, roentgen-phase and metallographic analyses. For the first time on the base of difference-thermal, roentgen-phase and metallographic analyses was formed the equilibrium diagram of Gd 5 Sb 3 -Tb 5 Sb 3 system. Was determined the cristal-chemical parameters of solid solutions with general formula Gd x Tb 5 - x Sb 3

The nitric acid decomposition of calcined danburite concentrate of Ak-Arkhar Deposit

International Nuclear Information System (INIS)

Kurbonov, A.S.; Mamatov, E.D.; Suleymani, M.; Borudzherdi, A.; Mirsaidov, U.M.

2011-01-01

Present article is devoted to nitric acid decomposition of calcined danburite concentrate of Ak-Arkhar Deposit of Tajikistan. The obtaining of boric acid from pre backed danburite concentrate by decomposition of nitric acid was studied. The chemical composition of danburite concentrate was determined. The laboratory study of danburite leaching by nitric acid was conducted. The influence of temperature, process duration, nitric acid concentration on nitric acid decomposition of calcined danburite concentrate of Ak-Arkhar Deposit was studied as well. The optimal conditions of nitric acid decomposition of calcined danburite concentrate of Ak-Arkhar Deposit, including temperature, process duration, nitric acid concentration and particle size were proposed.

Screening Level Risk Assessment for the New Waste Calcining Facility

Energy Technology Data Exchange (ETDEWEB)

M. L. Abbott; K. N. Keck; R. E. Schindler; R. L. VanHorn; N. L. Hampton; M. B. Heiser

1999-05-01

This screening level risk assessment evaluates potential adverse human health and ecological impacts resulting from continued operations of the calciner at the New Waste Calcining Facility (NWCF) at the Idaho Nuclear Technology and Engineering Center (INTEC), Idaho National Engineering and Environmental Laboratory (INEEL). The assessment was conducted in accordance with the Environmental Protection Agency (EPA) report, Guidance for Performing Screening Level Risk Analyses at Combustion Facilities Burning Hazardous Waste. This screening guidance is intended to give a conservative estimate of the potential risks to determine whether a more refined assessment is warranted. The NWCF uses a fluidized-bed combustor to solidify (calcine) liquid radioactive mixed waste from the INTEC Tank Farm facility. Calciner off volatilized metal species, trace organic compounds, and low-levels of radionuclides. Conservative stack emission rates were calculated based on maximum waste solution feed samples, conservative assumptions for off gas partitioning of metals and organics, stack gas sampling for mercury, and conservative measurements of contaminant removal (decontamination factors) in the off gas treatment system. Stack emissions were modeled using the ISC3 air dispersion model to predict maximum particulate and vapor air concentrations and ground deposition rates. Results demonstrate that NWCF emissions calculated from best-available process knowledge would result in maximum onsite and offsite health and ecological impacts that are less then EPA-established criteria for operation of a combustion facility.

In Vitro Studies Evaluating Leaching of Mercury from Mine Waste Calcine Using Simulated Human Body Fluids

OpenAIRE

Gray, John E.; Plumlee, Geoffrey S.; Morman, Suzette A.; Higueras, Pablo L.; Crock, James G.; Lowers, Heather A.; Witten, Mark L.

2010-01-01

In vitro bioaccessibility (IVBA) studies were carried out on samples of mercury (Hg) mine-waste calcine (roasted Hg ore) by leaching with simulated human body fluids. The objective was to estimate potential human exposure to Hg due to inhalation of airborne calcine particulates and hand-to-mouth ingestion of Hg-bearing calcines. Mine waste calcines collected from Hg mines at Almad?n, Spain, and Terlingua, Texas, contain Hg sulfide, elemental Hg, and soluble Hg compounds, which constitute prim...

Waste Calcining Facility remote inspection report

International Nuclear Information System (INIS)

Patterson, M.W.; Ison, W.M.

1994-08-01

The purpose of the Waste Calcining Facility (WCF) remote inspections was to evaluate areas in the facility which are difficult to access due to high radiation fields. The areas inspected were the ventilation exhaust duct, waste hold cell, adsorber manifold cell, off-gas cell, calciner cell and calciner vessel. The WCF solidified acidic, high-level mixed waste generated during nuclear fuel reprocessing. Solidification was accomplished through high temperature oxidation and evaporation. Since its shutdown in 1981, the WCFs vessels, piping systems, pumps, off-gas blowers and process cells have remained contaminated. Access to the below-grade areas is limited due to contamination and high radiation fields. Each inspection technique was tested with a mock-up in a radiologically clean area before the equipment was taken to the WCF for the actual inspection. During the inspections, essential information was obtained regarding the cleanliness, structural integrity, in-leakage of ground water, indications of process leaks, indications of corrosion, radiation levels and the general condition of the cells and equipment. In general, the cells contain a great deal of dust and debris, as well as hand tools, piping and miscellaneous equipment. Although the building appears to be structurally sound, the paint is peeling to some degree in all of the cells. Cracking and spalling of the concrete walls is evident in every cell, although the east wall of the off-gas cell is the worst. The results of the completed inspections and lessons learned will be used to plan future activities for stabilization and deactivation of the facility. Remote clean-up of loose piping, hand tools, and miscellaneous debris can start immediately while information from the inspections is factored into the conceptual design for deactivating the facility

Structural and Electronic Features of Sb-Based Electrode Materials: 121Sb Moessbauer Spectrometry

International Nuclear Information System (INIS)

Ionica, C. M.; Aldon, L.; Lippens, P. E.; Morato, F.; Olivier-Fourcade, J.; Jumas, J.-C.

2004-01-01

Lithium insertion mechanisms in two antimony based compounds: CoSb 3 and CoSb have been studied by means of 121 Sb Moessbauer spectrometry. Structural and electronic modifications induced by insertion of lithium have been characterised for different depths of discharge. In all cases the insertion mechanisms can be described from several steps. In the first step antimony is partially dispersed in the metallic matrix with amorphisation of the electrode material and in a second step we can observe the alloy forming (Li 3 Sb). However this amorphous alloy remains in interaction with the matrix allowing then a good reversibility.

Photoemission study of the skutterudite compounds CoSb sub 3 and RhSb sub 3

CERN Document Server

Ishii, H; Fujimori, A; Nagamoto, Y; Koyanagi, T; Sofo, J O

2002-01-01

We have studied the electronic structure of the skutterudite compounds CoSb sub 3 and Co(Sb sub 0 sub . sub 9 sub 6 Te sub 0 sub . sub 0 sub 4) sub 3 by photoemission spectroscopy. Valence-band spectra revealed that a significant amount Sb 5p states are present near the Fermi level and are hybridized with Co 3d states just below it. The spectra are well reproduced by the band-structure calculation, suggesting that the effect of electron correlations is not important. When Te is substituted for Sb and n-type carriers are doped into CoSb sub 3 , the spectra are shifted to higher binding energies as described by the rigid-band model. From this shift and the free-electron model for the conduction and valence bands, we have estimated the band gap of CoSb sub 3 to be 0.03-0.04 eV, consistent with transport measurements. Photoemission spectra of RhSb sub 3 have also been measured and revealed expected similarities to and differences from those of CoSb sub 3. Unusual temperature dependence has been observed for the s...

Fluidized bed system for calcination of high level radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Pande, D P; Prasad, T L; Yadgiri, N K; Theyyunni, T K [Process Engineering and Systems Development Division, Bhabha Atomic Research Centre, Mumbai (India)

1994-06-01

During the operation of nuclear facilities significant quantities of radiochemical liquid effluents of different concentrations and varying chemical compositions are generated. These effluents contain activated radionuclides, corrosion products and fission products. The advantage of feeding the waste in solid form into the vitrifying equipment are multifold. Efforts are therefore made in many countries to calcine the high level waste, and obtain waste in the oxide form before the same is mixed with glass forming additives and fed into the melter unit. An experimental rig for fluidized bed calcination is constructed for carrying out the detailed investigation of this process, in order to adopt the same for plant scale application. To achieve better gas-solid contact and avoid raining down of solids, a distributor of bubble cap type was designed. A review of existing experience at various laboratories and design of new experimental facility for development of calciners are given. (author). 11 refs., 5 figs.

Electrodeposition and electrochemical characterisation of thick and thin coatings of Sb and Sb/Sb2O3 particles for Li-ion battery anodes

International Nuclear Information System (INIS)

Bryngelsson, Hanna; Eskhult, Jonas; Edstroem, Kristina; Nyholm, Leif

2007-01-01

The possibilities to electrodeposit thick coatings composed of nanoparticles of Sb and Sb 2 O 3 for use as high-capacity anode materials in Li-ion batteries have been investigated. It is demonstrated that the stability of the coatings depends on their Sb 2 O 3 concentrations as well as microstructure. The electrodeposition reactions in electrolytes with different pH and buffer capacities were studied using chronopotentiometry and electrochemical quartz crystal microbalance measurements. The obtained deposits, which were characterised with XRD and SEM, were also tested as anode materials in Li-ion batteries. The influence of the pH and buffer capacity of the deposition solution on the composition and particle size of the deposits were studied and it is concluded that depositions from a poorly buffered solution of antimony-tartrate give rise to good anode materials due to the inclusion of precipitated Sb 2 O 3 nanoparticles in the Sb coatings. Depositions under conditions yielding pure Sb coatings give rise to deposits composed of large crystalline particles with poor anode stabilities. The presence of a plateau at about 0.8 V versus Li + /Li due to SEI forming reactions and the origin of another plateau at about 0.4 V versus Li + /Li seen during the lithiation of thin Sb coatings are also discussed. It is demonstrated that the 0.4 V plateau is present for Sb coatings for which the (0 1 2) peak is the main peak in the XRD diffractogram

[Sb{sub 4}Au{sub 4}Sb{sub 4}]{sup 2−}: A designer all-metal aromatic sandwich

Energy Technology Data Exchange (ETDEWEB)

Tian, Wen-Juan; You, Xue-Rui [Nanocluster Laboratory, Institute of Molecular Science, Shanxi University, Taiyuan 030006 (China); Guo, Jin-Chang [Department of Chemistry, Xinzhou Teachers University, Xinzhou 034000 (China); Li, Da-Zhi, E-mail: hj.zhai@sxu.edu.cn, E-mail: ldz005@126.com [Department of Chemical Engineering, Binzhou University, Binzhou 256603 (China); Wang, Ying-Jin [Nanocluster Laboratory, Institute of Molecular Science, Shanxi University, Taiyuan 030006 (China); Department of Chemistry, Xinzhou Teachers University, Xinzhou 034000 (China); Sun, Zhong-Ming [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Zhai, Hua-Jin, E-mail: hj.zhai@sxu.edu.cn, E-mail: ldz005@126.com [Nanocluster Laboratory, Institute of Molecular Science, Shanxi University, Taiyuan 030006 (China); State Key Laboratory of Quantum Optics and Quantum Optics Devices, Shanxi University, Taiyuan 030006 (China)

2016-07-28

We report on the computational design of an all-metal aromatic sandwich, [Sb{sub 4}Au{sub 4}Sb{sub 4}]{sup 2−}. The triple-layered, square-prismatic sandwich complex is the global minimum of the system from Coalescence Kick and Minima Hopping structural searches. Following a standard, qualitative chemical bonding analysis via canonical molecular orbitals, the sandwich complex can be formally described as [Sb{sub 4}]{sup +}[Au{sub 4}]{sup 4−}[Sb{sub 4}]{sup +}, showing ionic bonding characters with electron transfers in between the Sb{sub 4}/Au{sub 4}/Sb{sub 4} layers. For an in-depth understanding of the system, one needs to go beyond the above picture. Significant Sb → Au donation and Sb ← Au back-donation occur, redistributing electrons from the Sb{sub 4}/Au{sub 4}/Sb{sub 4} layers to the interlayer Sb–Au–Sb edges, which effectively lead to four Sb–Au–Sb three-center two-electron bonds. The complex is a system with 30 valence electrons, excluding the Sb 5s and Au 5d lone-pairs. The two [Sb{sub 4}]{sup +} ligands constitute an unusual three-fold (π and σ) aromatic system with all 22 electrons being delocalized. An energy gap of ∼1.6 eV is predicted for this all-metal sandwich. The complex is a rare example for rational design of cluster compounds and invites forth-coming synthetic efforts.

Study of variation grain size in desulfurization process of calcined petroleum coke

Science.gov (United States)

Pintowantoro, Sungging; Setiawan, Muhammad Arif; Abdul, Fakhreza

2018-04-01

Indonesia is a country with abundant natural resources, such as mineral mining and petroleum. In petroleum processing, crude oil can be processed into a source of fuel energy such as gasoline, diesel, oil, petroleum coke, and others. One of crude oil potentials in Indonesia is petroleum coke. Petroleum coke is a product from oil refining process. Sulfur reducing process in calcined petroleum cokes can be done by desulfurization process. The industries which have potential to become petroleum coke processing consumers are industries of aluminum smelting (anode, graphite block, carbon mortar), iron riser, calcined coke, foundry coke, etc. Sulfur reducing process in calcined petroleum coke can be done by thermal desulfurization process with alkaline substance NaOH. Desulfurization of petroleum coke process can be done in two ways, which are thermal desulfurization and hydrodesulphurization. This study aims to determine the effect of various grain size on sulfur, carbon, and chemical bond which contained by calcined petroleum coke. The raw material use calcined petroleum coke with 0.653% sulfur content. The grain size that used in this research is 50 mesh, then varied to 20 mesh and 100 mesh for each desulfurization process. Desulfurization are tested by ICP, UV-VIS, and FTIR to determine levels of sulfur, carbon, chemical bonding and sulfur dissolved water which contained in the residual washing of calcined petroleum coke. From various grain size that mentioned before, the optimal value is on 100 mesh grain size, where the sulfur content in petroleum coke is 0.24% and carbon content reaches the highest level of 97.8%. Meanwhile for grain size 100 mesh in the desulfurization process is enough to break the chemical bonds of organic sulfur in petroleum coke.

Evaluation of Calcine Disposition Path Forward

International Nuclear Information System (INIS)

Birrer, S.A.; Heiser, M.B.

2003-01-01

This document describes an evaluation of the baseline and two alternative disposition paths for the final disposition of the calcine wastes stored at the Idaho Nuclear Technology and Engineering Center at the Idaho National Engineering and Environmental Laboratory. The pathways are evaluated against a prescribed set of criteria and a recommendation is made for the path forward

Synthesis of well-dispersed ZnO nanomaterials by directly calcining zinc stearate

International Nuclear Information System (INIS)

Guo Guangsheng; Shi Chen; Tao Dongliang; Qian Weizhong; Han Dongmei

2009-01-01

Well-dispersed ZnO nanomaterials were synthesized by direct calcination of zinc stearate. Results from Fourier transform infrared (FT-IR) spectra and X-ray diffraction (XRD) indicated both the decomposition degree of organic ligand and the purity of calcined products were increased with the calcination temperature. The influence of decomposition temperature on the morphology of ZnO nanomaterials was investigated by field-emission scanning electron microscopy (FE-SEM) and transmission electron microscopy (TEM). The experimental results revealed the morphology of ZnO transformed from nanosheets to hexagonal nanopyramids and then to nanoparticles at 573, 673 and 773 K respectively. Finally, a morphology evolution model of ZnO nanomaterials under different temperatures was proposed

The increase performance BMF-14 calcination unit

International Nuclear Information System (INIS)

Triyono

2013-01-01

The heating element of performance increase BMF-14 calcination unit has been installed. The activity includes: installation and function test heating element step by step. The main component includes: kanthal heating element type with size long 58,2 cm diameter 0,9 cm slot total 28, flexible cable resists heat 30 Amperes, band cable heat resists and flexible clamp. The heating elements installation includes from 3 groups and every groups have 4 heating elements to connectly series. Every group connecting to every phase RST and neutral for getting electric voltage 380 Volts follow contact relay 3 phases to controlling by digital temperature control. The resulting installation of heating element in the BMF-14 calcination unit showed that: BMF-14 calcination unit can be again of the setting temperature step by step. In the step I get optimal temperature 560 °C test time 1068 minutes with rate velocity heat 0 to 18,0 °C/minutes with current between 5,8 to 6,4 Amperes voltage 103 to 123 Volts (phase R and T). In the step II gets optimal temperature 600 °C test time 265 minutes getting rate velocity heat 0 to 40,3 °C/minutes with current 3,8 to 8,5 Amperes voltage 76 to 142 Volts (phase RST). In the step III gets optimal temperature 1000 °C test time 107 minutes getting rate velocity heat 0 to 53,5 °C/minutes with current 9,7 to 12,5 Amperes voltage 215 to 225 Volts (phase RST). (author)

In As{sub 1–x}Sb{sub x} heteroepitaxial structures on compositionally graded GaInSb and AlGaInSb buffer layers

Energy Technology Data Exchange (ETDEWEB)

Guseynov, R. R.; Tanriverdiyev, V. A. [National Academy of Sciences of Azerbaijan, Institute of Physics (Azerbaijan); Kipshidze, G., E-mail: gela.kishidze@stonybrook.ede [Stony Brook, Stony Brook University (United States); Aliyeva, Ye. N.; Aliguliyeva, Kh. V.; Abdullayev, N. A., E-mail: abnadir@mail.ru; Mamedov, N. T. [National Academy of Sciences of Azerbaijan, Institute of Physics (Azerbaijan)

2017-04-15

Unrelaxed InAs{sub 1–x}Sb{sub x} (x = 0.43 and 0.38) alloy layers are produced by molecular-beam epitaxy on compositionally graded GaInSb and AlGaInSb buffer layers. The high quality of the thin films produced is confirmed by the results of high-resolution X-ray diffraction analysis and micro-Raman studies. The twomode type of transformation of the phonon spectra of InAs{sub 1–x}Sb{sub x} alloys is established.

Origin of Activity and Stability Enhancement for Ag3PO4 Photocatalyst after Calcination

Directory of Open Access Journals (Sweden)

Pengyu Dong

2016-11-01

Full Text Available Pristine Ag3PO4 microspheres were synthesized by a co-precipitation method, followed by being calcined at different temperatures to obtain a series of calcined Ag3PO4 photocatalysts. This work aims to investigate the origin of activity and stability enhancement for Ag3PO4 photocatalyst after calcination based on the systematical analyses of the structures, morphologies, chemical states of elements, oxygen defects, optical absorption properties, separation and transfer of photogenerated electron-hole pairs, and active species. The results indicate that oxygen vacancies (VO˙˙ are created and metallic silver nanoparticles (Ag NPs are formed by the reaction of partial Ag+ in Ag3PO4 semiconductor with the thermally excited electrons from Ag3PO4 and then deposited on the surface of Ag3PO4 microspheres during the calcination process. Among the calcined Ag3PO4 samples, the Ag3PO4-200 sample exhibits the best photocatalytic activity and greatly enhanced photocatalytic stability for photodegradation of methylene blue (MB solution under visible light irradiation. Oxygen vacancies play a significantly positive role in the enhancement of photocatalytic activity, while metallic Ag has a very important effect on improving the photocatalytic stability. Overall, the present work provides some powerful evidences and a deep understanding on the origin of activity and stability enhancement for the Ag3PO4 photocatalyst after calcination.

Limiting scattering processes in high-mobility InSb quantum wells grown on GaSb buffer systems

Science.gov (United States)

Lehner, Ch. A.; Tschirky, T.; Ihn, T.; Dietsche, W.; Keller, J.; Fält, S.; Wegscheider, W.

2018-05-01

We present molecular beam epitaxial grown single- and double-side δ -doped InAlSb/InSb quantum wells with varying distances down to 50 nm to the surface on GaSb metamorphic buffers. We analyze the surface morphology as well as the impact of the crystalline quality on the electron transport. Comparing growth on GaSb and GaAs substrates indicates that the structural integrity of our InSb quantum wells is solely determined by the growth conditions at the GaSb/InAlSb transition and the InAlSb barrier growth. The two-dimensional electron gas samples show high mobilities of up to 349 000 cm2/Vs at cryogenic temperatures and 58 000 cm2/Vs at room temperature. With the calculated Dingle ratio and a transport lifetime model, ionized impurities predominantly remote from the quantum well are identified as the dominant source of scattering events. The analysis of the well-pronounced Shubnikov-de Haas oscillations reveals a high spin-orbit coupling with an effective g -factor of -38.4 in our samples. Along with the smooth surfaces and long mean free paths demonstrated, our InSb quantum wells are increasingly competitive for nanoscale implementations of Majorana mode devices.

Model for the sulfidation of calcined limestone and its use in reactor models.

NARCIS (Netherlands)

Heesink, Albertus B.M.; Brilman, Derk Willem Frederik; van Swaaij, Willibrordus Petrus Maria

1998-01-01

A mathematical model describing the sulfidation of a single calcined limestone particle was developed and experimentally verified. This model, which includes no fitting parameters, assumes a calcined limestone particle to consist of spherical grains of various sizes that react with H2S according to

An Assessment of Using Vibrational Compaction of Calcined HLW and LLW in DWPF Canisters

International Nuclear Information System (INIS)

Yi, Yun-Bo; Amme, Robert C.; Shayer, Zeev

2008-01-01

Since 1963, the INEL has calcined almost 8 million gallons of liquid mixed waste and liquid high-level waste, converting it to some 1.1 million gallons of dry calcine (about 4275.0 m3), which consists of alumina-and zirconia-based calcine and zirconia-sodium blend calcine. In addition, if all existing and projected future liquid wastes are solidified, approximately 2,000 m3 of additional calcine will be produced primarily from sodium-bearing waste. Calcine is a more desirable material to store than liquid radioactive waste because it reduces volume, is much less corrosive, less chemically reactive, less mobile under most conditions, easier to monitor and more protective of human health and the environment. This paper describes the technical issue involved in the development of a feasible solution for further volume reduction of calcined nuclear waste for transportation and long term storage, using a standard DWPF canister. This will be accomplished by developing a process wherein the canisters are transported into a vibrational machine, for further volume reduction by about 35%. The random compaction experiments show that this volume reduction is achievable. The main goal of this paper is to demonstrate through computer modeling that it is feasible to use volume reduction vibrational machine without developing stress/strain forces that will weaken the canister integrity. Specifically, the paper presents preliminary results of the stress/strain analysis of the DWPF canister as a function of granular calcined height during the compaction and verifying that the integrity of the canister is not compromised. This preliminary study will lead to the development of better technology for safe compactions of nuclear waste that will have significant economical impact on nuclear waste storage and treatment. The preliminary results will guide us to find better solutions to the following questions: 1) What are the optimum locations and directions (vertical versus horizontal or

Adducts of UF5 with SbF5 and structure of UF5 . 2SbF5

International Nuclear Information System (INIS)

Sawodny, W.; Rediess, K.

1980-01-01

Both α-UF 5 and β-UF 5 form only a 1:2 compound UF 5 . 2SbF 5 reacting directly with SbF 5 , from which UF 5 . SbF 5 can be obtained by thermal decomposition. UF 5 . 2SbF 5 crystallizes in the monoclinic space group P2 1 /c with the following lattice constants a = 8.110(4), b = 14.129(6), c = 10.032(6) A and β = 96.97(5) 0 ; Z = 4. An X-ray study shows centrosymmetric four-membered rings of alternating UF 8 and SbF 6 polyhedra connected by other SbF 6 entities. This structure is similar to that of UOF 5 . 2SbF 5 , but the distorted pentagonal-bipyramidal coordination of the U atom found there is increased to a dodecahedral coordination by an additional U-F-Sb bridge, though with a somewaht larger UF distance. (author)

Study of conformational changes and protein aggregation of bovine serum albumin in presence of Sb(III) and Sb(V).

Science.gov (United States)

Verdugo, Marcelo; Ruiz Encinar, Jorge; Costa-Fernández, José Manuel; Menendez-Miranda, Mario; Bouzas-Ramos, Diego; Bravo, Manuel; Quiroz, Waldo

2017-01-01

Antimony is a metalloid that affects biological functions in humans due to a mechanism still not understood. There is no doubt that the toxicity and physicochemical properties of Sb are strongly related with its chemical state. In this paper, the interaction between Sb(III) and Sb(V) with bovine serum albumin (BSA) was investigated in vitro by fluorescence spectroscopy, and circular dichroism (CD) under simulated physiological conditions. Moreover, the coupling of the separation technique, asymmetric flow field-flow fractionation, with elemental mass spectrometry to understand the interaction of Sb(V) and Sb(III) with the BSA was also used. Our results showed a different behaviour of Sb(III) vs. Sb(V) regarding their effects on the interaction with the BSA. The effects in terms of protein aggregates and conformational changes were higher in the presence of Sb(III) compared to Sb(V) which may explain the differences in toxicity between both Sb species in vivo. Obtained results demonstrated the protective effect of GSH that modifies the degree of interaction between the Sb species with BSA. Interestingly, in our experiments it was possible to detect an interaction between BSA and Sb species, which may be related with the presence of labile complex between the Sb and a protein for the first time.

Reaction between Hydrogen Sulfide and Limestone Calcines

Czech Academy of Sciences Publication Activity Database

Hartman, Miloslav; Svoboda, Karel; Trnka, Otakar; Čermák, Jiří

2002-01-01

Roč. 41, č. 10 (2002), s. 2392-2398 ISSN 0888-5885 R&D Projects: GA AV ČR IAA4072711; GA AV ČR IAA4072801 Keywords : hydrogen sulfide * limestone calcines * desulfurization Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 1.247, year: 2002

A Summary of Rheology Data For SB3 and SB2/3 Blend Simulant Savannah River Site Wastes

International Nuclear Information System (INIS)

KOOPMAN, DAVIDC.

2004-01-01

The purpose of this study was to document the rheological measurements made for Sludge Batch 3 (SB3) and the blend of SB3 with Sludge Batch 2 (SB2). These measurements were primarily made on Slurry Mix Evaporator (SME) products, i.e. melter feeds. Some measurements were made on SB2/3 blend Sludge Receipt and Adjustment Tank (SRAT) products. Measurements on radioactive SB3 and SB2/3 samples have been limited to sludge characterization. SB2/3 measurements studied the impact of changing the SRAT acid addition strategy on the SRAT and SME product rheology. SB2/3 measurements also studied the impact of changing the waste loading target (sludge oxides content in glass) of the SME product. SB3 measurements studied the impact of changes in the wash end point and acid addition strategy on the SME product (melter feed) rheology. A summary of the significant findings is given below: SB3 radioactive sludge and blended SB2/3 radioactive sludge were less viscous than SB2 radioactive sludge. SB2/3 b lend sludge is more viscous than SB3 sludge. SB3 simulant SME product rheology was strongly impacted by changing the noble metal concentrations to more closely match those of the qualification sample. This reduction in noble metals produced a lower pH product that was also considerably less viscous. Increased acid addition in the SB2/3 SRAT generally led to less viscous simulant SRAT products. This trend did not persist in the SME products. SME products became more viscous when increased acid was used in the SRAT cycle from 135 per cent up to 170 per cent of stoichiometry, then became less viscous as total acid was increased further to 185 per cent. A significant increase in hydrogen generation occurred between 170 per cent and 185 per cent. The impact of acid addition on SB3 SME products was also variable. The impact of waste loading changes from 31 to 35 to 40 per cent on SB2/3 simulant SME products led to more viscous melter feeds as waste loading increased at constant wt. per cent

Can iron plaque affect Sb(III) and Sb(V) uptake by plants under hydroponic conditions

NARCIS (Netherlands)

Ji, Ying; Lenz, Markus; Lenz, Markus; Schulin, Rainer; Tandy, Susan

2018-01-01

Antimony (Sb) contamination of soils is of concern due to h uman activities such as recycling of Sb containing Pb acid batteries, shooting and mining. However Sb uptake by plants is poorly documented, especially when plants are growing on waterlogged soils and iron plaques form on their roots. The

Crystallization and memory programming characteristics of Ge-doped SbTe materials of varying Sb : Te ratio

International Nuclear Information System (INIS)

Jeong, Jeung-hyun; Lee, Hyun Seok; Lee, Suyoun; Lee, Taek Sung; Kim, Won Mok; Wu Zhe; Cheong, Byung-ki; Kim, Seul Cham; Oh, Kyu Hwan

2009-01-01

A phase change memory (PCM) utilizes resistivity changes accompanying fast transitions from an amorphous to a crystalline phase (SET) and vice versa (RESET). An investigation was made on the SET characteristics of PCM cells with Ge-doped SbTe (Ge-ST) materials of two different Sb : Te ratios (4.53 and 2.08). For the material of higher Sb : Te (4.53), a SET operation was completed within several tens of nanoseconds via nucleation-free crystallization whereas the material of lower Sb : Te (2.08) rendered a slower SET operation requiring several hundred nanoseconds for a nucleation-mediated crystallization. From measurements of nucleation and growth kinetics via laser-induced crystallization, the observed SET characteristics of the former case were found to derive from a growth time about 10 3 times shorter than the nucleation time and those of the latter from a much shorter nucleation time as well as a longer growth time than in the former case. The measured nucleation kinetics of the lower Sb : Te (2.08) material is unexpected from the existing data, which has led us to advance an interesting finding that there occurs a trend-reversing change in the nucleation kinetics of the Ge-ST materials around the eutectic composition (Sb : Te ∼2.6); nucleation is accelerated with the increase in the Sb : Te ratio above Sb : Te of 2.6, but with a decrease in the Sb : Te ratio below it.

Polarity-dependent resistance switching in GeSbTe phase-change thin films : The importance of excess Sb in filament formation

NARCIS (Netherlands)

Pandian, Ramanathaswamy; Kooi, Bart J.; Oosthoek, Jasper L. M.; van den Dool, Pim; Palasantzas, George; Pauza, Andrew

2009-01-01

We show that polarity-dependent resistance switching in GeSbTe thin films depends strongly on Sb composition by comparing current-voltage characteristics in Sb-excess Ge(2)Sb(2+x)Te(5) and stoichiometric Ge(2)Sb(2)Te(5) samples. This type of switching in Ge(2)Sb(2+x)Te(5) films is reversible with

The flashcal process for the fabrication of fuel-metal oxides using the whiteshell roto-spray calciner

International Nuclear Information System (INIS)

Sridhar, T.S.

1988-01-01

A one-step, continuous, thermochemical calcination process, called the FLASHCAL (Flash Calcination) process has been developed for the production of single- and mixed-oxide powders of fuel metals (uranium, thorium and plutonium) from the respective nitrate solutions using the Whiteshell Roto-Spray Calciner (RSC). The metal-nitrate feed solution, either by itself or mixed with a suitable chemical reactant or additive, is converted to its oxide powder in the RSC at temperatures between 300 and 600 0 C. Rapid denitration takes place in the calciner, yielding the metal-oxide powders while simultaneously destroying any excess chemical additive and reaction by-products. In the production of precursor oxide powders suitable for fuel fabrication, the FLASHCAL process has advantages over batch calcination and other processes that involve precipitation and filtration steps because fewer processing and handling operations are needed. Results obtained with thorium nitrate and uranium nitrate-thorium nitrate mixtures indicate that some measure of control over the size distribution and morphology of the oxide product powders is possible in this process with the proper selection of chemical additive, as well as the operating parameters of the calciner

Design criteria for the new waste calcining facility at the Idaho Chemical Processing Plant

International Nuclear Information System (INIS)

Anderson, F.H.; Bingham, G.E.; Buckham, J.A.; Dickey, B.R.; Slansky, C.M.; Wheeler, B.R.

1976-01-01

The New Waste Calcining Facility (NWCF) at the Idaho Chemical Processing Plant (ICPP) is being built to replace the existing fluidized-bed, high-level waste calcining facility (WCF). Performance of the WCF is reviewed, equipment failures in WCF operation are examined, and pilot-plant studies on calciner improvements are given in relation to NWCF design. Design features of the NWCF are given with emphasis on process and equipment improvements. A major feature of the NWCF is the use of remote maintenance facilities for equipment with high maintenance requirements, thereby reducing personnel exposures during maintenance and reducing downtime resulting from plant decontamination. The NWCF will have a design net processing rate of 11.36 m 3 of high-level waste per day, and will incorporate in-bed combustion of kerosene for heating the fluidized bed calciner. The off-gas cleaning system will be similar to that for the WCF

A conceptual and calculational model for gas formation from impure calcined plutonium oxides

International Nuclear Information System (INIS)

Lyman, John L.; Eller, P. Gary

2000-01-01

Safe transport and storage of pure and impure plutonium oxides requires an understanding of processes that may generate or consume gases in a confined storage vessel. We have formulated conceptual and calculational models for gas formation from calcined materials. The conceptual model for impure calcined plutonium oxides is based on the data collected to date

The leaching of base minerals from the calcines produced by the roasting of pyrite concentrates

International Nuclear Information System (INIS)

Nicol, M.J.; Filmer, A.O.

1985-01-01

A number of gold and uranium plants in South Africa concentrate the pyrite in the ore residue by flotation and roast the concentrate for the production of sulphuric acid. The calcine produced, which is predominantly hematite, is generally subjected to cyanidation for the recovery of gold and silver. The calcines often contain economically significant quantities of copper, nickel , cobalt and uranium. Prior treatment of the calcine for the recovery of these metals would be desirable in terms of the value of the products. Several processes for the leaching of the base metals from plant calcines have been investigated, and an important general conclusion is that an adequate recovery of the base metals requires that a large proportion of the iron should also be extracted. This observation led to a more extensive investigation of the kinetics of leaching of various iron oxides. The application of electrochemical theory and techniques resulted in a fuller understanding of the various factors that govern the rate of leaching of iron oxides. As a result of this fundamental work, alternative treatment schemes that should yield more efficient extraction from calcines were suggested. Several of these possibilities were investigated, and the most promising were found to require reducing conditions during the leach, or prior partial reduction of the calcine to magnetite or wustite

AgSbSe2 and AgSb(S,Se)2 thin films for photovoltaic applications

International Nuclear Information System (INIS)

Garza, J.G.; Shaji, S.; Rodriguez, A.C.; Das Roy, T.K.; Krishnan, B.

2011-01-01

Silver antimony selenide (AgSbSe 2 ) thin films were prepared by heating sequentially deposited multilayers of antimony sulphide (Sb 2 S 3 ), silver selenide (Ag 2 Se), selenium (Se) and silver (Ag). Sb 2 S 3 thin film was prepared from a chemical bath containing SbCl 3 and Na 2 S 2 O 3 , Ag 2 Se from a solution containing AgNO 3 and Na 2 SeSO 3 and Se thin films from an acidified solution of Na 2 SeSO 3 , at room temperature on glass substrates. Ag thin film was deposited by thermal evaporation. The annealing temperature was 350 deg. C in vacuum (10 -3 Torr) for 1 h. X-ray diffraction analysis showed that the thin films formed were polycrystalline AgSbSe 2 or AgSb(S,Se) 2 depending on selenium content in the precursor films. Morphology and elemental analysis of these films were done using scanning electron microscopy and energy dispersive X-ray spectroscopy. Optical band gap was evaluated from the UV-visible absorption spectra of these films. Electrical characterizations were done using Hall effect and photocurrent measurements. A photovoltaic structure: glass/ITO/CdS/AgSbSe 2 /Al was formed, in which CdS was deposited by chemical bath deposition. J-V characteristics of this structure showed V oc = 435 mV and J sc = 0.08 mA/cm 2 under illumination using a tungsten halogen lamp. Preparation of a photovoltaic structure using AgSbSe 2 as an absorber material by a non-toxic selenization process is achieved.

Reactive ion etching of GaSb, (Al,Ga)Sb, and InAs for novel device applications

International Nuclear Information System (INIS)

LaTulipe, D.C.; Frank, D.J.; Munekata, H.

1991-01-01

Although a variety of novel device proposals for GaSb/(Al,Ga)Sb/InAs heterostructures have been made, relatively little is known about processing these materials. The authors of this paper have studied the reactive ion etching characteristics of GaSb, (Al,Ga)Sb, and InAs in both methane/hydrogen and chlorine gas chemistries. At conditions similar to those reported elsewhere for RIE of InP and GaAs in CH 4 /H 2 , the etch rate of (Al,Ga)Sb was found to be near zero, while GaSb and InAs etched at 200 Angstrom/minute. Under conditions where the etch mechanism is primarily physical sputtering, the three compounds etch at similar rates. Etching in Cl 2 was found to yield anistropic profiles, with the etch rate of (Al,Ga)Sb increasing with Al mole fraction, while InAs remains unetched. Damage to the InAs stop layer was investigated by sheet resistance and mobility measurements. These etching techniques were used to fabricate a novel InAs- channel FET composed of these materials. Several scanning electron micrographs of etching results are shown along with preliminary electrical characteristics

Evaporation of tetramers in Sb4n clusters and conditions for the formation of Sb2n+1 clusters

International Nuclear Information System (INIS)

Rayane, D.; Tribollet, B.; Broyer, M.; Melinon, P.; Cabaud, B.; Hoareau, A.

1989-01-01

Antimony clusters are produced by the inert gas condensation technique. They are found to be built from Sb 4 units. The fragmentation by evaporation of Sb 4 units is studied as a function of the excess energy in the cluster. By this way the binding energy of the Sb 4 units in the cluster is found to be about 1.5 eV, well below the binding energy of a Sb atom in the bulk and in Sb 4 (≅3 eV). The evolution of ionization potentials of Sb 4n clusters confirms that their structure is probably non metallic. Finally the possible metastable character of this Sb 4n structure is discussed. (orig.)

Optimization of growth parameters for MOVPE-grown GaSb and Ga1−xInxSb

International Nuclear Information System (INIS)

Miya, S.S.; Wagener, V.; Botha, J.R.

2012-01-01

The triethylgallium/trimethylantimony (TEGa/TMSb) precursor combination was used for the metal-organic vapour phase epitaxial growth of GaSb at a growth temperature of 520 °C at atmospheric pressure. Trimethylindium was added in the case of Ga 1−x In x Sb growth. The effects of group V flux to group III flux ratio (V/III ratio) on the crystallinity and optical properties of GaSb layers are reported. It has been observed from the crystalline quality and optical properties that nominal V/III ratios of values greater than unity are required for GaSb epitaxial layers grown at this temperature. It has also been shown that Ga 1−x In x Sb can be grown using TEGa as a source of gallium species at atmospheric pressure. The relationship between Ga 1−x In x Sb vapour composition and solid composition has been studied at a V/III ratio of 0.78.

Ninth Processing Campaign in the Waste Calcining Facility

International Nuclear Information System (INIS)

Childs, K.F.; Donovan, R.I.; Swenson, M.C.

1982-04-01

This report discusses the Ninth (and final) Processing Campaign at the Waste Calcining Facility. Several processing interruptions were experienced during this campaign and the emphasis of this report is on process and equipment performance with operating problems and corrective actions discussed in detail

In situ study of the formation kinetics of InSb quantum dots grown in an InAs(Sb) matrix

International Nuclear Information System (INIS)

Semenov, A. N.; Lyublinskaya, O. G.; Solov’ev, V. A.; Mel’tser, B. Ya.; Ivanov, S. V.

2008-01-01

Formation of InSb quantum dots grown in an InAs matrix by molecular-beam epitaxy that does not involve forced deposition of InSb is studied. Detection of intensity oscillations in the reflection of high-energy electron diffraction patterns was used to study in situ the kinetics of the formation of InSb quantum dots and an InAsSb wetting layer. The effects of the substrate temperature, the shutter operation sequence, and the introduction of growth interruptions on the properties of the array of InSb quantum dots are examined. Introduction of a growth interruption immediately after completing the exposure of the InAs surface to the antimony flux leads to a reduction in the nominal thickness of InSb and to an enhancement in the uniformity of the quantum-dot array. It is shown that, in the case of deposition of submonolayer-thickness InSb/InAs quantum dots, the segregation layer of InAsSb plays the role of the wetting layer. The Sb segregation length and segregation ratio, as well as their temperature dependences, are determined.

121Sb-NMR study of filled skutterudite CeOs4Sb12

International Nuclear Information System (INIS)

Yogi, M.; Niki, H.; Mukuda, H.; Kitaoka, Y.; Sugawara, H.; Sato, H.

2007-01-01

121 Sb nuclear magnetic resonance (NMR) of filled skutterudite compound CeOs 4 Sb 12 has been carried out to investigate a spin fluctuation below T∼25K. In spite of a powdered sample, many sharp peaks, similar to a data for single crystal, were observed because of an orientation of the sample from the anisotropy of the magnetization. A numerical calculation well reproduces resonance fields for Sb(1) sites with H parallel V zz . The nuclear spin-lattice relaxation rate divided by temperature 1/T 1 T shows continuous decrease with increasing magnetic field, indicating a suppression of the spin fluctuation by the field

Determination of the Rate of Formation of Hydroceramic Waste Forms made with INEEL Calcined Wastes

Energy Technology Data Exchange (ETDEWEB)

Barry Scheetz; Johnson Olanrewaju

2001-10-15

The formulation, synthesis, characterization and hydration kinetics of hydroceramic waste forms designed as potential hosts for existing INEEL calcine high-level wastes have been established as functions of temperature and processing time. Initial experimentations were conducted with several aluminosilicate pozzolanic materials, ranging from fly ash obtained from various power generating coal and other combustion industries to reactive alumina, natural clays and ground bottled glass powders. The final selection criteria were based on the ease of processing, excellent physical properties and chemical durability (low-leaching) determined from the PCT test produced in hydroceramic. The formulation contains vermiculite, Sr(NO32), CsC1, NaOH, thermally altered (calcined natural clay) and INEEL simulated calcine high-level nuclear wastes and 30 weight percent of fluorinel blend calcine and zirconia calcine. Syntheses were carried out at 75-200 degree C at autogeneous water pressure (100% relative humidity) at various time intervals. The resulting monolithic compact products were hard and resisted breaking when dropped from a 5 ft height. Hydroceramic host mixed with fluorinel blend calcine and processed at 75 degree C crumbled into rice hull-side grains or developed scaly flakes. However, the samples equally possessed the same chemical durability as their unbroken counterparts. Phase identification by XRD revealed that hydroceramic host crystallized type zeolite at 75-150 degree C and NaP1 at 175-200 degree C in addition to the presence of quartz phase originating from the clay reactant. Hydroceramic host mixed with either fluorinel blend calcine or zirconia calcine crystallized type A zeolite at 75-95 degree C, formed a mixture of type A zeolite and hydroxysodalite at 125-150 degree C and hydroxysodalite at 175-200 degree C. Quartz, calcium fluoride and zirconia phases from the clay reactant and the two calcine wastes were also detected. The PCT test solution

Effect of calcination routes on phase formation of BaTiO3 and their electronic and magnetic properties

Science.gov (United States)

Majumder, Supriyo; Choudhary, R. J.; Tripathi, M.; Phase, D. M.

2018-05-01

We have investigated the phase formation and correlation between electronic and magnetic properties of oxygen deficient BaTiO3 ceramics, synthesized by solid state reaction method, following different calcination paths. The phase analysis divulge that a higher calcination temperature above 1000° C is favored for tetragonal phase formation than the cubic phase. The core level X-ray photo electron spectroscopy measurements confirm the presence of oxygen vacancies and oxygen vacancy mediated Ti3+ states. As the calcination temperature and calcination time increases these oxygen vacancies and hence Ti3+ concentrations reduce in the sample. The temperature dependent magnetization curves suggest unexpected magnetic ordering, which may be due to the presence of unpaired electron at the t2g state (d1) of nearest-neighbor Ti atoms. In magnetization vs magnetic field isotherms, the regular decrease of saturation moment value with increasing calcination temperature and calcination time, can be discussed considering the amount of oxygen deficiency induced Ti3+ concentrations, present in the sample.

Cyclic carbonation calcination studies of limestone and dolomite for CO{sub 2} separation from combustion flue gases - article no. 011801

Energy Technology Data Exchange (ETDEWEB)

Senthoorselvan, S.; Gleis, S.; Hartmut, S.; Yrjas, P.; Hupa, M. [TUM, Garching (Germany)

2009-01-15

Naturally occurring limestone and dolomite samples, originating from different geographical locations, were tested as potential sorbents for carbonation/calcination based CO{sub 2} capture from combustion flue gases. Samples have been studied in a thermogravimetric analyzer under simulated flue gas conditions at three calcination temperatures, viz., 750{sup o}C, 875{sup o}C, and 930{sup o}C for four carbonation calcination reaction (CCR) cycles. The dolomite sample exhibited the highest rate of carbonation than the tested limestones. At the third cycle, its CO{sub 2} capture capacity per kilogram of the sample was nearly equal to that of Gotland, the highest reacting limestone tested. At the fourth cycle it surpassed Gotland, despite the fact that the CaCO{sub 3} content of the Sibbo dolomite was only 2/3 of that of the Gotland. Decay coefficients were calculated by a curve fitting exercise and its value is lowest for the Sibbo dolomite. That means, most probably its capture capacity per kilogram of the sample would remain higher well beyond the fourth cycle. There was a strong correlation between the calcination temperature, the specific surface area of the calcined samples, and the degree of carbonation. It was observed that the higher the calcination temperature, the lower the sorbent reactivity. For a given limestone/dolomite sample, sorbents CO{sub 2} capture capacity depended on the number of CCR cycles and the calcination temperature. According to the equilibrium thermodynamics, the CO{sub 2} partial pressure in the calciner should be lowered to lower the calcination temperature. This can be achieved by additional steam supply into the calciner. Steam could then be condensed in an external condenser to single out the CO{sub 2} stream from the exit gas mixture of the calciner. A calciner design based on this concept is illustrated.

Phase equilibria melt-solid in the systems Pb-InSb-CaSb and Pb-InCs-GaAs

International Nuclear Information System (INIS)

Grebenyuk, A.M.; Charykov, N.A.; Puchkov, L.V.

1992-01-01

Results of experimental investigation and thermodynamic calculation of fusibility curves of Pb-InSb-GaSb and Pb-InAs-GaAs thernary systems, which haven't been investigated earlier, are presented. Fusibility curves of Pb-InSb-GaSb and Pb-InAs-GaAs systems contain two crystallization fields: solid solutions of In x Ga 1-x Sb and Pb, In x Ga 1-x As and Pb. The latter fields are retained against Pb figurative point and conform to 582 K < T < 593 K crystallization temperatures

Formation Mechanism of Self Assembled Horizontal ErSb Nanowires Embedded in a GaSb(001) Matrix

Science.gov (United States)

Wilson, Nathaniel; Kraemer, Stephan; PalmstrøM, Chris

The ErxGa1-xSb exhibits a variety of self-assembling nanostructures. In order to harness these nanostructures for use in devices and other material systems it is important to understand their formation. We have characterized the growth mechanism of self-assembled horizontal ErSb nanowires in a GaSb(001) matrix through the use of in-situ Scanning Tunneling Microscopy (STM) as well as ex-situ Transmission Electron Microscopy (TEM). We observe large GaSb macrosteps on the growth surface of Er.3Ga.7Sb samples. The areas near the ledge and base of the macrosteps show significant differences in size and distribution of ErSb nanowires. Results suggest that the formation of macrosteps drives the transition from vertical to horizontal nanowires in the ErxGa1-xSb system. We also observe a low temperature growth mode, which results in horizontal nanowire formation under a wide range of flux conditions. This new growth mode does not exhibit the embedded growth observed in the formation of nanowires at higher temperatures and may allow for horizontal nanowire formation without the presence of macrosteps, as well as the formation of smaller nanoparticles which may be useful for achieving smaller nanoparticle dimensions and electron confinement effects. This work was supported by NSF-DMR under 1507875.

Stabilized γ-BIMNVOX solid electrolyte: Ethylene glycol–citrate sol–gel synthesis, microwave-assisted calcination, and structural and electrical characterization

Energy Technology Data Exchange (ETDEWEB)

Al-Areqi, Niyazi A.S., E-mail: niyazi.alareqi@gmail.com [Department of Chemistry, Faculty of Applied Science, Taiz University, Taiz, Republic of Yemen (Yemen); Beg, Saba [Department of Chemistry, Aligarh Muslim University, Aligarh 202002 (India); Al-Alas, Ahlam [Department of Chemistry, Faculty of Applied Science, Taiz University, Taiz, Republic of Yemen (Yemen); Hafeez, Shehla [Department of Chemistry, Aligarh Muslim University, Aligarh 202002 (India)

2013-12-25

Highlights: •γ-BIMNVOX was synthesized by ethylene glycol–citrate sol–gel route. •γ-BIMNVOX crystallizes by 25-min microwave-assisted calcination. •Smaller particle sizes for microwave calcined BIMNVOX samples. •Best oxide-ion performance for microwave calcined BIMNVOX samples. -- Abstract: Samples of γ-BIMNVOX (Bi{sub 2}V{sub 1−x}Mn{sub x}O{sub 5.5−x/2}; 0.13 ⩽ x ⩽ 0.20) system were synthesized by an ethylene glycol–citrate sol–gel route. The resulting xerogels were then calcined by the microwave heating using a modified domestic microwave oven operated at 2.45 GHz. Microwave-assisted calcination samples in comparison with other conventionally calcined samples were characterized in terms of phase crystallization, stabilization and particle size using simultaneous thermogravimetric–differential thermal analysis (TG–DTA), X-ray powder diffraction (XRPD) and scanning electron microscopy (SEM). The AC impedance spectroscopy was employed for electrical characterization. It was found that the microwave-assisted calcination route successfully produces better crystalline stabilized γ-BIMNVOX samples with appreciably small average particle sizes after only 25 min of microwave heating. The electrical properties of microwave calcined γ-BIMNVOX system make it an advanced low-temperature solid electrolyte suitable for use in oxide-ion based electrochemical applications.

Decomposition of pre calcined aluminium silicate ores of Afghanistan by hydrochloric acid

International Nuclear Information System (INIS)

Khomidi, A.K.; Mamatov, E.D.

2015-01-01

Present article is devoted to decomposition of pre calcined aluminium silicate ores of Afghanistan by hydrochloric acid. The physicochemical properties of initial aluminium silicate ores were studied by means of X-ray phase, differential thermal and silicate analysis. The chemical composition of aluminium containing ores was determined. The optimal conditions of interaction of initial and pre calcined siallites with hydrochloric acid were defined. The kinetics of acid decomposition of aluminium silicate ores was studied as well.

Effect of Sb content on the thermoelectric properties of annealed CoSb_3 thin films deposited via RF co-sputtering

International Nuclear Information System (INIS)

Ahmed, Aziz; Han, Seungwoo

2017-01-01

Graphical abstract: The X-ray diffraction patterns and temperature dependence of the Seebeck coefficient of the annealed Co–Sb thin films. - Highlights: • CoSb_3 phase thin films were prepared using RF co sputtering method. • Thin film thermoelectric properties were hugely dependent on Sb content. • All thin films shows n-type conduction behavior at high temperatures. • The thin films with excess Sb possess the largest Seebeck coefficient. • The thin films with CoSb_2 phase possess the largest power factor. - Abstract: A series of CoSb_3 thin films with Sb contents in the range 70–79 at.% were deposited at room temperature via RF co-sputtering. The thin films were amorphous in the as-deposited state and annealed at 300 °C for 3 h to obtain crystalline samples. The annealed thin films were characterized using scanning electron microscopy and X-ray diffraction (XRD), and these data indicate that the films exhibited good crystallinity. The XRD patterns indicate single-phase CoSb_3 thin films in the Sb-rich samples. For the Sb-deficient samples, however, mixed-phase thin films consisting of CoSb_2 and CoSb_3 components were obtained. The electrical and thermoelectric properties were measured at temperatures up to 760 K and found to be highly sensitive to the phases that were present. We observed a change in the thermoelectric properties of the films from p-type at low temperatures to n-type at high temperatures, which indicates potential applications as n-type thermoelectric thin films. A large Seebeck coefficient and power factor was obtained for the single-phase CoSb_3 thin films. The CoSb_2 phase thin films were also found to possess a significant Seebeck coefficient, which coupled with the much smaller electrical resistivity, provided a larger power factor than the single-phase CoSb_3 thin films. We report maximum power factor of 7.92 mW/m K"2 for the CoSb_2-containing mixed phase thin film and 1.26 mW/m K"2 for the stoichiometric CoSb_3 thin film.

Design of a hot pilot plant facility for demonstration of the pot calcination process

Energy Technology Data Exchange (ETDEWEB)

Buckham, J A

1962-01-01

A facility was designed for demonstration of the pot calcination process with wastes from processing aluminum alloy fuels, Darex or electrolytic processing of stainless-steel fuels, and Purex processes. This facility will also permit determination of procedures required for economical production of low-porosity, relatively nonleachable materials by addition of suitable reagents to the wastes fed to the calciner. The process consists of concentration by evaporation and thermal decomposition in situ in pots which also serve as the final disposal containers. This unit permits determination of pot loading and density, leachability, melting point, volatile material content, heat release, and thermal conductivity of the calcine. Also to be determined are transient calcine temperature distributions, fission product behavior during calcination, deentrainment obtained in the various parts of the system, decontamination achieved on all liquid and gaseous effluent streams, need for venting of stored pots, optimum means of remotely sealing the pots, and methods required for production of a minimum volume of noncondensable off-gas. This facility will employ nominal full-scale pots 8 and 12 in. in diameter and 8 ft long. A unique evaporator design was evolved to permit operation either with close-coupled continuous feed preparation or with bath feed preparation. Provisions were made to circumvent possible explosions due to organic material in feed solutions and other suspected hazards.

Effect of antimony nano-scale surface-structures on a GaSb/AlAsSb distributed Bragg reflector

International Nuclear Information System (INIS)

Husaini, S.; Shima, D.; Ahirwar, P.; Rotter, T. J.; Hains, C. P.; Dang, T.; Bedford, R. G.; Balakrishnan, G.

2013-01-01

Effects of antimony crystallization on the surface of GaSb during low temperature molecular beam epitaxy growth are investigated. The geometry of these structures is studied via transmission electron and atomic force microscopies, which show the surface metal forms triangular-shaped, elongated nano-wires with a structured orientation composed entirely of crystalline antimony. By depositing antimony on a GaSb/AlAsSb distributed Bragg reflector, the field is localized within the antimony layer. Polarization dependent transmission measurements are carried out on these nano-structures deposited on a GaSb/AlAsSb distributed Bragg reflector. It is shown that the antimony-based structures at the surface favor transmission of light polarized perpendicular to the wires.

Processing of concentrated radioactive wastes into cement and bitumens following calcination

International Nuclear Information System (INIS)

Napravnik, J.; Sazavsky, P.; Ditl, P.; Prikryl, P.

1985-01-01

A brief characteristic is presented of the most frequently used processes of solidification of liquid radioactive wastes, viz., bituminization, cementation and their combination with calcination. The effect of individual parameters is assessed on the choice of the type of solidification process as is their importance in the actual process, in temporary storage, during transportation and under conditions of long-term storage. It has been found that a combination of the procedures could lead to a modular system of methods and equipment. This would allow to approach optimal solidification of wastes in the present period and to establish a research reserve for the development of more modern, economically advantageous and safer procedures. A rough estimate is made of the costs of the solidification of 1 m 3 of radioactive concentrate from the V-1 power plant at a production of 380 m 3 /year, this for the cementation-calcination and bituminization-calcination procedures. The said rough economic analysis only serves to identify the major operating components which have the greatest effect on the economic evaluation of the solidification procedures. (Z.M.)

Calcined clay lightweight ceramics made with wood sawdust and sodium silicate

Energy Technology Data Exchange (ETDEWEB)

Santis, Bruno Carlos de; Rossignolo, Joao Adriano, E-mail: desantis.bruno@gmail.com [Universidade de Sao Paulo (USP), Pirassununga, SP (Brazil); Morelli, Marcio Raymundo [Universidade Federal de Sao Carlos (UFSCar), SP (Brazil). Departamento de Engenharia de Materiais

2016-11-15

This paper aims to study the influence of including wood sawdust and sodium silicate in the production process of calcined clay lightweight ceramics. In the production process first, a sample used by a company that produces ceramic products in Brazil was collected. The sample was analysed by techniques of liquidity (LL) and plasticity (LP) limits, particle size analysis, specific mass, X-ray diffraction (XRD) and X ray fluorescence spectrometry (XRF). From the clay, specimens of pure clay and mixtures with wood sawdust (10%, 20% and 30% by mass) and sodium silicate were produced and fired at a temperature of 900 deg C. These specimens were submitted to tests of water absorption, porosity, specific mass and compressive strength. Results of this research indicate that the incorporation of wood sawdust and sodium silicate in the ceramic paste specimens can be useful to make calcined clay lightweight ceramics with special characteristics (low values of water absorption and specific mass and high values of compressive strength), which could be used to produce calcined clay lightweight aggregates to be used in structural concrete. (author)

Calcinated tea and cellulose composite films and its dielectric and lead adsorption properties.

Science.gov (United States)

Jayaramudu, Tippabattini; Varaprasad, Kokkarachedu; Kim, Hyun Chan; Kafy, Abdullahil; Kim, Jung Woong; Kim, Jaehwan

2017-09-01

In this paper, calcinated tea and cellulose composite (CTCC) films were fabricated via solution casting method. Chemical structure, morphology, crystallinity and thermal stability of the fabricated films were characterized by using Fourier transform infrared spectroscopy, scanning electron microscopy, X-ray diffraction and thermogravimetric analysis. The effect of calcinated tea loading on the properties of the prepared CTCC films was studied. The results suggest that the prepared CTCC films show higher mechanical properties, thermal stability and dielectric constant than the neat cellulose film. In addition, the CTCC films adsorb Pb 2+ ions and its adsorption performance depends on the calcinated tea content and pH level. The CTCC films are useful for sensors, flexible capacitor as well as lead adsorption applications. Copyright © 2017 Elsevier Ltd. All rights reserved.

The variation of cationic microstructure in Mn-doped spinel ferrite during calcination and its effect on formaldehyde catalytic oxidation

Energy Technology Data Exchange (ETDEWEB)

Liang, Xiaoliang [CAS Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Guangdong Provincial Key Laboratory of Mineral Physics and Materials, Guangzhou 510640 (China); Liu, Peng [CAS Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Guangdong Provincial Key Laboratory of Mineral Physics and Materials, Guangzhou 510640 (China); He, Hongping, E-mail: hehp@gig.ac.cn [CAS Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Guangdong Provincial Key Laboratory of Mineral Physics and Materials, Guangzhou 510640 (China); Wei, Gaoling [Guangdong Institute of Eco-Environmental and Soil Sciences, Guangzhou 510650 (China); Chen, Tianhu [School of Resources and Environmental Engineering, Hefei University of Technology, Hefei 230009 (China); Tan, Wei; Tan, Fuding [CAS Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Guangdong Provincial Key Laboratory of Mineral Physics and Materials, Guangzhou 510640 (China); Zhu, Jianxi; Zhu, Runliang [CAS Key Laboratory of Mineralogy and Metallogeny, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, Guangzhou 510640 (China); Guangdong Provincial Key Laboratory of Mineral Physics and Materials, Guangzhou 510640 (China)

2016-04-05

Highlights: • Calcination causes the activity variation of Mn-doped ferrites for HCHO oxidation. • The variation of catalytic activity of ferrites by calcination is non-linear. • Mn enriches on the calcinated ferrite surface in the valence of +3 and +4. • The reduction temperature of surface Mn{sup 4+} species is well correlated to T50. - Abstract: In this study, a series of Mn substituted spinel ferrites calcinated at different temperatures were used as catalysts for the oxidation of formaldehyde (HCHO). X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and H{sub 2} temperature-programmed reduction were conducted to characterize the structure and physico-chemical properties of catalysts, which were affected by calcination in the range of 200–600 °C. Results show that all the ferrites were with spinel structure, and those calcinated in the range of 300–600 °C were in the phase of maghemite. The calcination changed the valence and distribution of Mn and Fe on the ferrite surface, and accordingly the reducibility of ferrites. The HCHO catalytic oxidation test showed that with the increase of calcination temperature, the activity was initially improved until 400 °C, but then decreased. The variation of HCHO conversion performance was well positively correlated to the variation of reduction temperature of surface Mn{sup 4+} species. The remarkable effect of calcination on the catalytic activity of Mn-doped spinel ferrites for HCHO oxidation was discussed in view of reaction mechanism and variations in cationic microstructure of Mn-doped ferrites.

The variation of cationic microstructure in Mn-doped spinel ferrite during calcination and its effect on formaldehyde catalytic oxidation

International Nuclear Information System (INIS)

Liang, Xiaoliang; Liu, Peng; He, Hongping; Wei, Gaoling; Chen, Tianhu; Tan, Wei; Tan, Fuding; Zhu, Jianxi; Zhu, Runliang

2016-01-01

Highlights: • Calcination causes the activity variation of Mn-doped ferrites for HCHO oxidation. • The variation of catalytic activity of ferrites by calcination is non-linear. • Mn enriches on the calcinated ferrite surface in the valence of +3 and +4. • The reduction temperature of surface Mn"4"+ species is well correlated to T50. - Abstract: In this study, a series of Mn substituted spinel ferrites calcinated at different temperatures were used as catalysts for the oxidation of formaldehyde (HCHO). X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy and H_2 temperature-programmed reduction were conducted to characterize the structure and physico-chemical properties of catalysts, which were affected by calcination in the range of 200–600 °C. Results show that all the ferrites were with spinel structure, and those calcinated in the range of 300–600 °C were in the phase of maghemite. The calcination changed the valence and distribution of Mn and Fe on the ferrite surface, and accordingly the reducibility of ferrites. The HCHO catalytic oxidation test showed that with the increase of calcination temperature, the activity was initially improved until 400 °C, but then decreased. The variation of HCHO conversion performance was well positively correlated to the variation of reduction temperature of surface Mn"4"+ species. The remarkable effect of calcination on the catalytic activity of Mn-doped spinel ferrites for HCHO oxidation was discussed in view of reaction mechanism and variations in cationic microstructure of Mn-doped ferrites.

Ce - promoted catalyst from hydrotalcites for CO2 reforming of methane: calcination temperature effect

Directory of Open Access Journals (Sweden)

Carlos Enrique Daza

2012-01-01

Full Text Available Ce-promoted Ni-catalysts from hydrotalcites were obtained. The effect of calcination temperature on the chemical and physical properties of the catalysts was studied. Several techniques were used to determine the chemical and physical characteristics of oxides. The apparent activation energies of reduction were determined. Catalytic experiments at 48 L g-1h-1 without pre-reduction in CO2 reforming of methane were performed. The spinel-like phase in these oxides was only formed at 1000 ºC. The reduction of Ni2+ in the oxides was clearly affected by the calcination temperature which was correlated with catalytic performance. The catalyst calcined at 700 ºC showed the greatest activity.

Calcined eggshell (CES): An efficient natural catalyst for ...

Indian Academy of Sciences (India)

hydes with active methylene compounds using calcined eggshell (CES) as an efficient ... of the important reactions to achieve carbon–carbon ... solid catalyst for biodiesel production,24 as a catalyst ... which supports for adsorption of water on CaO and ... The organic phase .... After extraction of the product with ethylac-.

Microwave energy for post-calcination treatment of high-level nuclear wastes

International Nuclear Information System (INIS)

Gombert, D.; Priebe, S.J.; Berreth, J.R.

1980-01-01

High-level radioactive wastes generated from nuclear fuel reprocessing require treatment for effective long-term storage. Heating by microwave energy is explored in processing of two possible waste forms: (1) drying of a pelleted form of calcined waste; and (2) vitrification of calcined waste. It is shown that residence times for these processes can be greatly reduced when using microwave energy rather than conventional heating sources, without affecting product properties. Compounds in the waste and in the glass frit additives couple very well with the 2.45 GHz microwave field so that no special microwave absorbers are necessary

Fuzzy modeling and control of the calcination process in a kiln

International Nuclear Information System (INIS)

Ramirez, M.; Haber, R.

1999-01-01

Calcination kilns are strongly nonlinear, multivariable processes, that only can be modeled with great uncertainty. In order to get a quality product and ensure the process efficiency, the controller must keep a prescribed temperature profile optimizing the fuel consumption. In this paper, a design methodology of a multivariable fuzzy controller for a nickel calcination kiln is presented. The controller structure is a classical one, and uses the Mamdani fuzzy inference system. In simulation results the fuzzy controller exhibits a great robustness in presence of several types of disturbances, and a better performance than the PID in same conditions is observed. (author)

Sb{sub 7}Te{sub 3}/ZnSb multilayer thin films for high thermal stability and long data retention phase-change memory

Energy Technology Data Exchange (ETDEWEB)

Chen, Shiyu; Wu, Weihua [Functional Materials Research Laboratory, School of Materials Science & Engineering, Tongji University, Shanghai 201804 (China); Zhai, Jiwei, E-mail: apzhai@tongji.edu.cn [Functional Materials Research Laboratory, School of Materials Science & Engineering, Tongji University, Shanghai 201804 (China); Song, Sannian; Song, Zhitang [State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Micro-system and Information Technology, Chinese Academy of Science, Shanghai 200050 (China)

2017-04-15

Highlights: • Sb{sub 7}Te{sub 3} (ST) provides a fast crystallization speed, low melting temperature. • The Sb{sub 7}Te{sub 3}/ZnSb films exhibits faster crystallization speed, high thermal stability. • The calculated temperature for 10-year data retention is about 127 {sup o}C. • The Sb{sub 7}Te{sub 3}/ZnSb multilayer configuration with low power consumption. - Abstract: Phase-change memory is regard as one of the most promising candidates for the next-generation non-volatile memory. In this work, we proposed a Sb{sub 7}Te{sub 3}/ZnSb multilayer thin films to improve the thermal stability of Sb-rich Sb{sub 3}Te{sub 7}. The sheet resistance ratio between amorphous and crystalline states reached up to 4 orders of magnitude. With regard to the thermal stability, the calculated temperature for 10-year data retention is about 127 °C. The threshold current and threshold voltage of a cell based on Sb{sub 7}Te{sub 3}/ZnSb are 6.9 μA and 1.9 V, respectively. The lower RESET power is presented in the PCM cells of Sb{sub 7}Te{sub 3}/ZnSb films, benefiting from its high resistivity.

(In)GaSb/AlGaSb quantum wells grown on Si substrates

International Nuclear Information System (INIS)

Akahane, Kouichi; Yamamoto, Naokatsu; Gozu, Shin-ichiro; Ueta, Akio; Ohtani, Naoki

2007-01-01

We have successfully grown GaSb and InGaSb quantum wells (QW) on a Si(001) substrate, and evaluated their optical properties using photoluminescence (PL). The PL emissions from the QWs at room temperature were observed at around 1.55 μm, which is suitable for fiber optic communications systems. The measured ground state energy of each QW matched well with the theoretical value calculated by solving the Schroedinger equation for a finite potential QW. The temperature dependence of the PL intensity showed large activation energy (∼ 77.6 meV) from QW. The results indicated that the fabricated QW structure had a high crystalline quality, and the GaSb QW on Si for optical devices operating at temperatures higher than room temperature will be expected

Role of Calcination Temperature on the Hydrotalcite Derived MgO–Al2O3 in Converting Ethanol to Butanol

Energy Technology Data Exchange (ETDEWEB)

Ramasamy, Karthikeyan K.; Gray, Michel J.; Job, Heather M.; Santosa, Daniel M.; Li, Xiaohong S.; Devaraj, Arun; Karkamkar, Abhijeet J.; Wang, Yong

2015-10-09

In the base catalyzed ethanol condensation reactions, the calcined MgO-Al₂O₃ derived hydrotalcites used broadly as catalytic material and the calcination temperature plays a big role in determining the catalytic activity. The characteristic of the hydrotalcite material treated between catalytically relevant temperatures 450ºC and 800ºC have been studied with respect to the physical, chemical, and structural properties and compared with catalytic activity testing. With the increasing calcination temperature, the total measured catalytic basicity dropped linearly with the calcination temperature and the total measured acidity stayed the same for all the calcination temperatures except 800ºC. However, the catalyst activity testing does not show any direct correlation between the measured catalytic basicity and the catalyst activity to the ethanol condensation reaction to form 1-butanol. The highest ethanol conversion of 44 percent with 1-butanol selectivity of 50 percent was achieved for the 600ºC calcined hydrotalcite material.

Sb(V reactivity with human blood components: redox effects.

Directory of Open Access Journals (Sweden)

Silvana López

Full Text Available We assessed the reactivity of Sb(V in human blood. Sb(V reactivity was determined using an HPLC-HG-AFS hyphenated system. Sb(V was partially reduced to Sb(III in blood incubation experiments; however, Sb(III was a highly unstable species. The addition of 0.1 mol L(-1 EDTA prevented Sb(III oxidation, thus enabling the detection of the reduction of Sb(V to Sb(III. The transformation of Sb(V to Sb(III in human whole blood was assessed because the reduction of Sb(V in human blood may likely generate redox side effects. Our results indicate that glutathione was the reducing agent in this reaction and that Sb(V significantly decreased the GSH/GSSG ratio from 0.32 ± 0.09 to 0.07 ± 0.03. Moreover, the presence of 200 ng mL(-1 of Sb(V increased the activity of superoxide dismutase from 4.4 ± 0.1 to 7.0 ± 0.4 U mL(-1 and decreased the activity of glutathione peroxidase from 62 ± 1 to 34 ± 2 nmol min(-1 mL(-1.

Synthesis of alumina powder with seeds by Pechini Method using O2 as calcination atmosphere

International Nuclear Information System (INIS)

Salem, R.E.P.; Guilherme, K.A.; Chinelatto, A.S.A.; Chinelatto, A. L.

2012-01-01

Alumina is a very investigated material due to its excellent refractory characteristics and mechanical properties. Its alpha phase, the most stable one, has a formation temperature of about 1200 ° C. Due to its high temperature of formation, many researches have been trying to reduce it through addition of seeds of alpha phase in chemical processes of synthesis. This work aims to synthesize ultrafine powders of alpha-alumina by the Pechini method with seeding, and using an O 2 atmosphere in the pre-calcination (500 ° C) and calcination (1000 ° C and 1100° C) steps. The resulting powders were characterized through X-ray diffractometry, infrared spectroscopy and scanning electron microscopy. The results were compared with samples calcined on ai. It was verified that the presence of oxygen in the calcination atmosphere favored the elimination of residual carbon from the precursor powders, forthcoming from the great amount of organic material used on the synthesis, modifying its morphology and favoring reduction of particle size. (author)

Effect of Sb content on the thermoelectric properties of annealed CoSb{sub 3} thin films deposited via RF co-sputtering

Energy Technology Data Exchange (ETDEWEB)

Ahmed, Aziz, E-mail: aziz_ahmed@ust.ac.kr [Department of Nano-Mechatronics, Korea University of Science and Technology (UST), 217 Gajeong-ro, Yuseong-gu, Daejeon, 305-350 (Korea, Republic of); Department of Nano-Mechanics, Korea Institute of Machinery and Materials (KIMM), 156 Gajeongbuk-ro, Yuseong-gu, Daejeon, 305-343 (Korea, Republic of); Han, Seungwoo, E-mail: swhan@kimm.re.kr [Department of Nano-Mechatronics, Korea University of Science and Technology (UST), 217 Gajeong-ro, Yuseong-gu, Daejeon, 305-350 (Korea, Republic of); Department of Nano-Mechanics, Korea Institute of Machinery and Materials (KIMM), 156 Gajeongbuk-ro, Yuseong-gu, Daejeon, 305-343 (Korea, Republic of)

2017-06-30

Graphical abstract: The X-ray diffraction patterns and temperature dependence of the Seebeck coefficient of the annealed Co–Sb thin films. - Highlights: • CoSb{sub 3} phase thin films were prepared using RF co sputtering method. • Thin film thermoelectric properties were hugely dependent on Sb content. • All thin films shows n-type conduction behavior at high temperatures. • The thin films with excess Sb possess the largest Seebeck coefficient. • The thin films with CoSb{sub 2} phase possess the largest power factor. - Abstract: A series of CoSb{sub 3} thin films with Sb contents in the range 70–79 at.% were deposited at room temperature via RF co-sputtering. The thin films were amorphous in the as-deposited state and annealed at 300 °C for 3 h to obtain crystalline samples. The annealed thin films were characterized using scanning electron microscopy and X-ray diffraction (XRD), and these data indicate that the films exhibited good crystallinity. The XRD patterns indicate single-phase CoSb{sub 3} thin films in the Sb-rich samples. For the Sb-deficient samples, however, mixed-phase thin films consisting of CoSb{sub 2} and CoSb{sub 3} components were obtained. The electrical and thermoelectric properties were measured at temperatures up to 760 K and found to be highly sensitive to the phases that were present. We observed a change in the thermoelectric properties of the films from p-type at low temperatures to n-type at high temperatures, which indicates potential applications as n-type thermoelectric thin films. A large Seebeck coefficient and power factor was obtained for the single-phase CoSb{sub 3} thin films. The CoSb{sub 2} phase thin films were also found to possess a significant Seebeck coefficient, which coupled with the much smaller electrical resistivity, provided a larger power factor than the single-phase CoSb{sub 3} thin films. We report maximum power factor of 7.92 mW/m K{sup 2} for the CoSb{sub 2}-containing mixed phase thin film and 1

ICPP radioactive liquid and calcine waste technologies evaluation final report and recommendation

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-01

Using a formalized Systems Engineering approach, the Latched Idaho Technologies Company developed and evaluated numerous alternatives for treating, immobilizing, and disposing of radioactive liquid and calcine wastes at the Idaho Chemical Processing Plant. Based on technical analysis data as of March, 1995, it is recommended that the Department of Energy consider a phased processing approach -- utilizing Radionuclide Partitioning for radioactive liquid and calcine waste treatment, FUETAP Grout for low-activity waste immobilization, and Glass (Vitrification) for high-activity waste immobilization -- as the preferred treatment and immobilization alternative.

Study of as-synthesized and calcined hydrocalumites as possible ...

Indian Academy of Sciences (India)

Administrator

ments. Finally, these solids were tested as antacids by using a synthetic gastric juice. Results showed that calcined samples were able to neutralize the synthetic gastric juice in more extension as an as-synthesized ..... D 2010 Appl. Clay Sci.

Determination of the Rate of Formation of Hydroceramic Waste Forms made with INEEL Calcined Wastes; FINAL

International Nuclear Information System (INIS)

Barry Scheetz; Johnson Olanrewaju

2001-01-01

The formulation, synthesis, characterization and hydration kinetics of hydroceramic waste forms designed as potential hosts for existing INEEL calcine high-level wastes have been established as functions of temperature and processing time. Initial experimentations were conducted with several aluminosilicate pozzolanic materials, ranging from fly ash obtained from various power generating coal and other combustion industries to reactive alumina, natural clays and ground bottled glass powders. The final selection criteria were based on the ease of processing, excellent physical properties and chemical durability (low-leaching) determined from the PCT test produced in hydroceramic. The formulation contains vermiculite, Sr(NO32), CsC1, NaOH, thermally altered (calcined natural clay) and INEEL simulated calcine high-level nuclear wastes and 30 weight percent of fluorinel blend calcine and zirconia calcine. Syntheses were carried out at 75-200 degree C at autogeneous water pressure (100% relative humidity) at various time intervals. The resulting monolithic compact products were hard and resisted breaking when dropped from a 5 ft height. Hydroceramic host mixed with fluorinel blend calcine and processed at 75 degree C crumbled into rice hull-side grains or developed scaly flakes. However, the samples equally possessed the same chemical durability as their unbroken counterparts. Phase identification by XRD revealed that hydroceramic host crystallized type zeolite at 75-150 degree C and NaP1 at 175-200 degree C in addition to the presence of quartz phase originating from the clay reactant. Hydroceramic host mixed with either fluorinel blend calcine or zirconia calcine crystallized type A zeolite at 75-95 degree C, formed a mixture of type A zeolite and hydroxysodalite at 125-150 degree C and hydroxysodalite at 175-200 degree C. Quartz, calcium fluoride and zirconia phases from the clay reactant and the two calcine wastes were also detected. The PCT test solution

Si-Sb-Te materials for phase change memory applications

International Nuclear Information System (INIS)

Rao Feng; Song Zhitang; Ren Kun; Zhou Xilin; Cheng Yan; Wu Liangcai; Liu Bo

2011-01-01

Si-Sb-Te materials including Te-rich Si 2 Sb 2 Te 6 and Si x Sb 2 Te 3 with different Si contents have been systemically studied with the aim of finding the most suitable Si-Sb-Te composition for phase change random access memory (PCRAM) use. Si x Sb 2 Te 3 shows better thermal stability than Ge 2 Sb 2 Te 5 or Si 2 Sb 2 Te 6 in that Si x Sb 2 Te 3 does not have serious Te separation under high annealing temperature. As Si content increases, the data retention ability of Si x Sb 2 Te 3 improves. The 10 years retention temperature for Si 3 Sb 2 Te 3 film is ∼ 393 K, which meets the long-term data storage requirements of automotive electronics. In addition, Si richer Si x Sb 2 Te 3 films also show improvement on thickness change upon annealing and adhesion on SiO 2 substrate compared to those of Ge 2 Sb 2 Te 5 or Si 2 Sb 2 Te 6 films. However, the electrical performance of PCRAM cells based on Si x Sb 2 Te 3 films with x > 3.5 becomes worse in terms of stable and long-term operations. Si x Sb 2 Te 3 materials with 3 < x < 3.5 are proved to be suitable for PCRAM use to ensure good overall performance.

Optical Properties and Photoactivity of The Pigmentary TiO2 Doped with P2O5, K2O, Al2O3 and Sb2O3

International Nuclear Information System (INIS)

Glen, M; Grzmil, B

2011-01-01

The influence of the increasing content of antimony calculated to Sb 2 O 3 (0.08-0.57 mol%) with the constant amount of the other additives (calculated to P 2 O 5 , K 2 O, Al 2 O 3 ) on the optical properties and photostability of doped rutile has been investigated. The properties of the obtained TiO 2 -PKAlSb samples were compared to the commercial TiO 2 -PKAl composition. The starting material was the concentrated suspension of technical-grade hydrated titanium dioxide (HTD). The dopant agents' solutions were introduced to HTD. Prepared samples were calcined with gradually increasing process temperature. The XRD analysis was used to determine the rutile content in the TiO 2 samples. Optical properties of modified titanium dioxide have been determined spectrophotometrically by measuring the colour in the white (brightness, white tone) and grey system (relative lightening power, grey tone). Photostability was characterized by the white lead-glycerin test with UV-Vis light. It was observed that with the increasing content of antimony in rutile TiO 2 , doped with phosphates, potassium and aluminium, the brightness and grey tone were increasing but white tone decreased. The changes of the relative lightening power values were insignificant. Comparing the samples of TiO 2 -PKAlSb with the TiO 2 -PKAl composition it was observed that titanium dioxide doped with antimony had better white and grey tone. The increasing Sb 2 O 3 content in the TiO 2 caused the improvement of the photostability.

Radiant-heat spray-calcination process for the solid fixation of radioactive waste. Part 1, Non-radioactive pilot unit

Energy Technology Data Exchange (ETDEWEB)

Allemann, R.T.; Johnson, B.M. Jr.

1960-11-14

The fixation of radioactive waste in a stable solid media by means of calcination of these aqueous solutions has been the subject of considerable-effort throughout the U. S. Atomic Energy Commission and by atomic energy organizations in other countries. Several methods of doing this on a continuous or semi-continuous basis have been devised, and a fev have been demonstrated to be feasible for the handling of non-radioactive, or low-activity, simulated wastes. Notable among methods currently under development are: (a) batch-operated pot calcination of waste generated from reprocessing stainless steel clad fuel elements (Darex process) and Purex waste, (b) combination rotary kiln and ball mill calcination of aluminum nitrate (TBP-25 and Redox process), and (c) fluidized bed calcination of TBP-25 and Purex wastes. Although a considerable amount of engineering experience has been obtained on the calcination of dissolved salts in a fluidized bed, and the other methods have been the subjects of a great deal of study, none of them have been developed to-the extent which would rule out the desirability of further investigation of other possible methods of calcination.

Neurotoxicological effects of cinnabar (a Chinese mineral medicine, HgS) in mice

International Nuclear Information System (INIS)

Huang, C.-F.; Liu, S.-H.; Lin-Shiau, S.-Y.

2007-01-01

Cinnabar, a naturally occurring mercuric sulfide (HgS), has long been used in combination with traditional Chinese medicine as a sedative for more than 2000 years. Up to date, its pharmacological and toxicological effects are still unclear, especially in clinical low-dose and long-term use. In this study, we attempted to elucidate the effects of cinnabar on the time course of changes in locomotor activities, pentobarbital-induced sleeping time, motor equilibrium performance and neurobiochemical activities in mice during 3- to 11-week administration at a clinical dose of 10 mg/kg/day. The results showed that cinnabar was significantly absorbed by gastrointestinal (G-I) tract and transported to brain tissues. The spontaneous locomotor activities of male mice but not female mice were preferentially suppressed. Moreover, frequencies of jump and stereotype-1 episodes were progressively decreased after 3-week oral administration in male and female mice. Pentobarbital-induced sleeping time was prolonged and the retention time on a rotating rod (60 rpm) was reduced after treatment with cinnabar for 6 weeks and then progressively to a greater extent until the 11-week experiment. In addition, the biochemical changes in blood and brain tissues were studied; the inhibition of Na + /K + -ATPase activities, increased production of lipid peroxidation (LPO) and nitric oxide (NO) were found with a greater extent in male mice than those in female mice, which were apparently correlated with their differences in the neurological responses observed. In conclusion, these findings, for the first time, provide evidence of the pharmacological and toxicological basis for understanding the sedative and neurotoxic effects of cinnabar used as a Chinese mineral medicine for more than 2000 years

Selection of a glass-ceramic formulation to immobilize fluorinel- sodium calcine

International Nuclear Information System (INIS)

Staples, B.A.; Wood, H.C.

1994-12-01

One option for immobilizing calcined high level wastes produced by nuclear fuel reprocessing activities at the Idaho Chemical Processing Plant (ICPP) is conversion to a glass-ceramic form through hot isostatic pressing. Calcines exist in several different chemical compositions, and thus candidate formulations have been developed for converting each to glass-ceramic forms which are potentially resistant to aqueous corrosion and stable enough to qualify for repository storage. Fluorinel/Na, a chemically complex calcine type, is one of the types being stored at ICPP, and development efforts have identified three formulations with potential for immobilizing it. These are a glass forming additive that uses aluminum metal to enhance reactivity, a second glass forming additive that uses titanium metal to enhance reactivity and a third that uses not only a combination of silicon and titanium metals but enough phosphorous pentoxide to form a calcium phosphate host phase in the glass-ceramic product. Glass-ceramics of each formulation performed well in restricted characterization tests. However, none of the three was subjected to rigorous testing that would provide information on whether each was processable, that is able to retain favorable characteristics over a practical range of processing conditions

Optimization of growth parameters for MOVPE-grown GaSb and Ga{sub 1-x}In{sub x}Sb

Energy Technology Data Exchange (ETDEWEB)

Miya, S.S.; Wagener, V. [Department of Physics, Private Bag X 77000, Nelson Mandela Metropolitan University, Port Elizabeth 6001 (South Africa); Botha, J.R., E-mail: reinhardt.botha@nmmu.ac.za [Department of Physics, Private Bag X 77000, Nelson Mandela Metropolitan University, Port Elizabeth 6001 (South Africa)

2012-05-15

The triethylgallium/trimethylantimony (TEGa/TMSb) precursor combination was used for the metal-organic vapour phase epitaxial growth of GaSb at a growth temperature of 520 Degree-Sign C at atmospheric pressure. Trimethylindium was added in the case of Ga{sub 1-x}In{sub x}Sb growth. The effects of group V flux to group III flux ratio (V/III ratio) on the crystallinity and optical properties of GaSb layers are reported. It has been observed from the crystalline quality and optical properties that nominal V/III ratios of values greater than unity are required for GaSb epitaxial layers grown at this temperature. It has also been shown that Ga{sub 1-x}In{sub x}Sb can be grown using TEGa as a source of gallium species at atmospheric pressure. The relationship between Ga{sub 1-x}In{sub x}Sb vapour composition and solid composition has been studied at a V/III ratio of 0.78.

Gel-combustion synthesis of CoSb2O6 and its reduction to powdery Sb2Co alloy

Directory of Open Access Journals (Sweden)

MAJA JOVIC

2009-01-01

Full Text Available Sb2Co alloy in powdery form was synthesized via reduction with gaseous hydrogen of the oxide CoSb2O6, obtained by the citrate gel-combustion technique. The precursor was an aqueous solution of antimony nitrate, cobalt nitrate and citric acid. The precursor solution with mole ratio Co(II/Sb(V of 1:2 was gelatinized by evaporation of water. The gel was heated in air up to the temperature of self-ignition. The product of gel combustion was a mixture of oxides and it had to be additionally thermally treated in order to be converted to pure CoSb2O6. The reduction of CoSb2O6 by gaseous hydrogen yielded powdery Sb2Co as the sole phase. The process of oxide reduction to alloy was controlled by thermogravimetry, while X-ray diffractometry was used to control the phase compositions of both the oxides and alloys.

Liquidus Projection and Isothermal Section of the Sb-Se-Sn System

Science.gov (United States)

Chang, Jui-shen; Chen, Sinn-wen

2017-12-01

Sb-Se-Sn ternary alloys are promising chalcogenide materials. The liquidus projection and 673.2 K (400 °C) isothermal section of the Sb-Se-Sn ternary system are determined. Numerous Sb-Se-Sn alloys are prepared, and their primary solidification phases are examined. In addition to the three terminal phases, (Sb), (Se) and (Sn), there are Sb2Sn3, SbSn, SnSe, SnSe2, Sb2Se3, Sn2Sb9Se9, and SnSb2Se4 phases. In addition, there are two miscibility gaps along the Sb-Se and Se-Sn and sides. There are ten invariant reactions in the Sb-Se-Sn ternary system, and seven of them are experimentally determined in this study. The lowest reaction temperature of determined invariant reaction is L + SbSn = (Sn) + SnSe at 515.4 K ± 5 K (242.2 °C ± 5 °C). There are nine tie-triangles, which are Liquid + SbSn + SnSe, SbSn + SnSe + (Sb), SnSe + (Sb) + Sn2Sb9Se9, (Sb) + Sb2Se3 + Sn2Sb9Se9, SnSe + Sn2Sb9Se9 + SnSb2Se4, Sb2Se3 + Sn2Sb9Se9 + SnSb2Se4, SnSe + SnSe2 + SnSb2Se4, SnSe2 + SnSb2Se4 + Sb2Se3, and SnSe2 + Sb2Se3 + Liquid in the 673.2 K (400 °C) isothermal section of the Sb-Se-Sn ternary system.

Structural Integrity Program for the Calcined Solids Storage Facilities at the Idaho Nuclear Technology and Engineering Center

International Nuclear Information System (INIS)

Bryant, J.W.; Nenni, J.A.

2003-01-01

This report documents the activities of the structural integrity program at the Idaho Nuclear Technology and Engineering Center relevant to the high-level waste Calcined Solids Storage Facilities and associated equipment, as required by DOE M 435.1-1, ''Radioactive Waste Management Manual.'' Based on the evaluation documented in this report, the Calcined Solids Storage Facilities are not leaking and are structurally sound for continued service. Recommendations are provided for continued monitoring of the Calcined Solids Storage Facilities

Structural Integrity Program for the Calcined Solids Storage Facilities at the Idaho Nuclear Technology and Engineering Center

International Nuclear Information System (INIS)

Jeffrey Bryant

2008-01-01

This report documents the activities of the structural integrity program at the Idaho Nuclear Technology and Engineering Center relevant to the high-level waste Calcined Solids Storage Facilities and associated equipment, as required by DOE M 435.1-1, 'Radioactive Waste Management Manual'. Based on the evaluation documented in this report, the Calcined Solids Storage Facilities are not leaking and are structurally sound for continued service. Recommendations are provided for continued monitoring of the Calcined Solids Storage Facilities

Phosphorous removal from aqueous solution can be enhanced through the calcination of lime sludge.

Science.gov (United States)

Bal Krishna, K C; Niaz, Mohamed R; Sarker, Dipok C; Jansen, Troy

2017-09-15

Water treatment plants generate an enormous amount of the sludge which is normally treated as waste. In the recent past, many investigations have been focused on developing an economical adsorbent using water treatment sludge to remove phosphorous (P) from aqueous solutions. However, the great extents of the studies have been limited in the use of alum- and iron-based sludges. This study, therefore, investigated the P removal performance of the calcined lime sludge. Calcined lime sludge at 700 °C significantly enhanced the P removal efficiency whereas marginal improvement was noted when the sludge calcined at 400 °C was tested. With increase P removal efficiency, final pH values of the solution also significantly increased. P removal efficiency of the calcined sludge decreased with increasing the initial P concentrations. However, the removal efficiency could be improved by increasing the weight of the sludge. Further analysis demonstrated that P removal trend followed both pseudo-second order and diffusion-chemisorption kinetics signifying the P removal is potentially due to a multi-mechanistic reaction in which, the process is controlled by intra-particle diffusion followed by chemisorptions. Copyright © 2017 Elsevier Ltd. All rights reserved.

Measurement of the loss on ignition of bulk calcined bauxite samples by neutron moderation

International Nuclear Information System (INIS)

Aylmer, J.A.; Borsaru, M.

1985-01-01

The production of high-grade calcined bauxite is very dependent on the moisture content of the final product. Existing procedures rely on the ignition of small samples to monitor the effectiveness of the calcination process. The results obtained by this gravimetric technique are several hours behind production and do not permit regular adjustment of the furnace to optimize the control of the chemically bound water content (LOI). To provide rapid and more relevant results, a neutron moderation technique has been developed for measuring the LOI of bulk samples of calcined bauxite while they are still hot. The method uses fast neutrons from an 241 Am-Be neutron source to irradiate the samples, and the backscattered thermal neutrons detected are a measure of bound moisture content. The rms deviation between neutron and conventional determinations of LOI, in 15 calcined bauxite samples, was 0.08 per cent LOI over the range 0.1 to 0.9 per cent LOI. When allowance is made for the rms error in the ignition method, the error in the neutron method is found to be 0.07 per cent LOI

Volatilities of ruthenium, iodine, and technetium on calcining fission product nitrate wastes

International Nuclear Information System (INIS)

Rimshaw, S.J.; Case, F.N.

1980-01-01

Various high-level nitrate wastes were subjected to formic acid denitration. Formic acid reacts with the nitrate anion to yield noncondensable, inert gases according to the following equation: 4 HCOOH + 2 HNO 3 → N 2 O + 4 CO 2 + 5 H 2 O. These gases can be scrubbed free of 106 Ru, 131 I, and 99 Tc radioactivities prior to elimination from the plant by passage through HEPA filters. The formation of deleterious NO/sub x/ is avoided. Moreover, formic acid reduces ruthenium to a lower valence state with a sharp reduction in RuO 4 volatility during subsequent calcination of the pretreated waste. It is shown that a minimum of 3% of RuO 4 in an off-gas stream reacts with Davison silica gel (Grade 40) to give a fine RuO 2 aerosol having a particle size of 0.5 μ. This RuO 2 aerosol passes through water or weak acid scrub solutions but is trapped by a caustic scrub solution. Iodine volatilizes almost completely on calcining an acidic waste, and the iodine volatility increases with increasing calcination temperature. On calcining an alkaline sodium nitrate waste the iodine volatility is about an order of magnitude lower, with a relatively low iodine volatility of 0.39% at a calcination temperature of 250 0 C and a moderate volatility of 9.5% at 600 0 C. Volatilities of 99 Tc were generally 0 C. Data are presented to indicate that 99 Tc concentrates in the alkaline sodium nitrate supernatant waste, with approx. 10 mg 99 Tc being associated with each curie of 137 Cs present in the waste. It is shown that lutidine (2,4 dimethyl-pyridine) extracts Tc(VII) quantitatively from alkaline supernatant wastes. The distribution coefficient (K/sub D/) for Tc(VII) going into the organic phase in the above system is 102 for a simulated West Valley waste and 191 for a simulated Savannah River Plant (SRP) waste

Reduction in thermal conductivity of BiSbTe lump

Energy Technology Data Exchange (ETDEWEB)

Ahmad, Kaleem [King Saud University, Sustainable Energy Technologies Center, College of Engineering, PO Box 800, Riyadh (Saudi Arabia); Wan, C. [Tsinghua University, State Key Laboratory of New Ceramics and Fine Processing, School of Materials Science and Engineering, Beijing (China); Al-Eshaikh, M.A.; Kadachi, A.N. [King Saud University, Research Center, College of Engineering, PO Box 800, Riyadh (Saudi Arabia)

2017-03-15

In this work, systematic investigations on the thermal conductivities of BiSbTe lump, microstructured pristine BiSbTe bulk and single wall carbon nanotubes (SWCNTs)/BiSbTe bulk nanocomposites were performed. BiSbTe lumps were crushed to form a coarse powder (200 μm) and effect of particle size reduction on the effective thermal conductivity of BiSbTe (200 μm) bulk were analyzed. For further reduction in the conductivity, a two pronged strategy has been employed. First, additional refinement of BiSbTe (200 μm) were performed through ball milling in an inert environment. Second, SWCNTs in 0.75, and 1.0 vol% were distributed uniformly in the fine BiSbTe ball milled powder. The results showed that the effective thermal conductivities decrease with the reduction in the particle size from lump to BiSbTe (200 μm) bulk as well as with the addition of SWCNTs accompanied by further refinement of BiSbTe particles. The significant reduction in thermal conductivities of the lump was achieved for pure BiSbTe (200 μm) bulk and 0.75 vol% of SWCNTs/BiSbTe composite. This can be ascribed to the enhanced phonon scattering by the grain boundaries between the nanostructured BiSbTe particles as well as the interfaces between BiSbTe and the low dimensional carbon nanotubes. (orig.)

Design and performance of atomizing nozzles for spray calcination of high-level wastes

International Nuclear Information System (INIS)

Miller, F.A.; Stout, L.A.

1981-05-01

A key aspect of high-level liquid-waste spray calcination is waste-feed atomization by using air atomizing nozzles. Atomization substantially increases the heat transfer area of the waste solution, which enhances rapid drying. Experience from the spray-calciner operations has demonstrated that nozzle flow conditions that produce 70-μ median-volume-diameter or smaller spray droplets are required for small-scale spray calciners (drying capacity less than 80 L/h). For large-scale calciners (drying capacity greater than 300 L/h), nozzle flow conditions that produce 100-μ median-volume-diameter or smaller spray droplets are required. Mass flow ratios of 0.2 to 0.4, depending on nozzle size, are required for proper operation of internal-mix atomizing nozzles. Both internal-mix and external-mix nozzles have been tested at PNL. Due to the lower airflow requirements and fewer large droplets produced, the internal-mix nozzle has been chosen for primary development in the spray calciner program at PNL. Several nozzle air-cap materials for internal-mix nozzles have been tested for wear resistance. Results show that nozzle air caps of stainless steel and Cer-vit (a machineable glass ceramic) are suceptible to rapid wear by abrasive slurries, whereas air caps of alumina and reaction-bonded silicon nitride show only slow wear. Longer-term testing is necessary to determine more accurately the actual frequency of nozzle replacement. Atomizing nozzle air caps of alumina are subject to fracture from thermal shock, whereas air caps of silicon nitride and Cer-vit are not. Fractured nozzles are held in place by the air-cap retaining ring and continue to atomize satisfactorily. Therefore, fractures caused by thermal shocking do not necessarily result in nozzle failure

Interim status of vertical calciner testing through calendar year 1996

International Nuclear Information System (INIS)

Compton, J.A.

1998-01-01

A prototype vertical calciner was constructed and tested for use in converting plutonium solutions to dry plutonium dioxide in the Hanford Plutonium Finishing Plant. Six non-radioactive runs were completed in June and July, 1995. Fourteen runs with plutonium nitrate solutions were completed between September, 1995 and August, 1996. Equipment modifications were made following those runs. The test runs with plutonium have converted 62.3 L of feed solution containing 11.1 kg of plutonium into dry plutonium dioxide containing 8.5 kg of plutonium. The decrease in product plutonium content is primarily due to plutonium accumulation within the calciner powder bed from particle compaction. Nine of the eleven product batches have had Losses On Ignition that met the storage criterion of less than 0.5 weight percent at 950 C. The highest Loss On Ignition found was 0.718 weight percent. Initial problems with agitator shaft binding and breakage of bushings have been eliminated. A feed pump control problem has been found and the pump replaced. Improvement in scrubber efficiency is needed. Future runs are planned to confirm that (1) the remainder of product meets the Loss On Ignition criterion, (2) the replacement feedpump works as needed, and (3) the scrubber efficiency improves. The operating staff for the production calciner may also be observing the prototype's runs to gain familiarity with the process and equipment

Effect of calcination conditions of pork bone sludge on behaviour

Indian Academy of Sciences (India)

... bone sludge from meat plant via two essentially different calcination methods using ... tissue and suitability for further investigations intended for medical grafting. ... The Alfred Meissner Higher School of Dental Engineering and Humanities, ...

Improvement of the crystallinity and photocatalytic property of zinc oxide as calcination product of Zn–Al layered double hydroxide

International Nuclear Information System (INIS)

Ahmed, Abdullah Ahmed Ali; Talib, Zainal Abidin; Hussein, Mohd Zobir bin; Zakaria, Azmi

2012-01-01

Highlights: ► ZnO phase and ZnAl 2 O 4 spinel can be formed as Zn–Al–NO 3 –LDH calcination products. ► The crystallinity of ZnO phase increased with an increase of calcination temperature. ► The optical band gaps of ZnO were improved with an increase in temperature. ► The oxygen vacancies in ZnO and ZnAl 2 O 4 generated the ESR signals. - Abstract: Zinc oxide with different degrees of crystallinity can be formed as Zn–Al-layered double hydroxide (Zn–Al–NO 3 –LDH) calcination products. ZnAl 2 O 4 spinel is also formed in a range of calcination temperatures from 600 to 1000 °C from the LDH. X-ray diffraction patterns showed that the crystallinity of the ZnO phase increased as calcination temperatures increased. The LDH structure was fully collapsed at and above 400 °C. The photocatalytic activity was determined by UV–VIS–NIR diffuse reflectance spectroscopy. The band gap of the calcined samples increased as the calcination temperature increased. Electron spin resonance (ESR) spectra of the fresh and calcined LDH at room temperature demonstrated that oxygen vacancies in the ZnO and ZnAl 2 O 4 were responsible for the generation of ESR signals. One BET specific surface area increased from 1 m 2 /g for the LDH to a maximum at 400 °C (43 m 2 /g) and decreased thereafter down to 6 m 2 /g at 1000 °C.

Optical and structural characterization of GaSb and Te-doped GaSb single crystals

International Nuclear Information System (INIS)

Tirado-Mejia, L.; Villada, J.A.; Rios, M. de los; Penafiel, J.A.; Fonthal, G.; Espinosa-Arbelaez, D.G.; Ariza-Calderon, H.; Rodriguez-Garcia, M.E.

2008-01-01

Optical and structural properties of GaSb and Te-doped GaSb single crystals are reported herein. Utilizing the photoreflectance technique, the band gap energy for doped samples was obtained at 0.814 eV. Photoluminescence (PL) spectra showed a peak at 0.748 eV that according to this research, belongs to electronic states of pure GaSb and not to the longitudinal optical (LO) phonon replica as has been reported by other authors. Analysis of the full width at half maximum (FWHM) values of X-ray diffraction, as well as micro-Raman peaks showed that the inclusion of Te decreases the crystalline quality

Oral administration of the 5-HT6 receptor antagonists SB-357134 and SB-399885 improves memory formation in an autoshaping learning task.

Science.gov (United States)

Perez-García, Georgina; Meneses, Alfredo

2005-07-01

In this work we aimed to re-examine the 5-HT6 receptor role, by testing the selective antagonists SB-357134 (1-30 mg/kg p.o.) and SB-399885 (1-30 mg/kg p.o.) during memory consolidation of conditioned responses (CR%), in an autoshaping Pavlovian/instrumental learning task. Bioavailability, half-life and minimum effective dose to induce inappetence for SB-357134 were 65%, 3.4 h, and 30 mg/kg p.o., and for SB-399885 were 52%, 2.2 h, and 50 mg/kg p.o., respectively. Oral acute and chronic administration of either SB-357134 or SB-399885 improved memory consolidation compared to control groups. Acute administration of SB-357134, at 1, 3, 10 and 30 mg/kg, produced a CR% inverted-U curve, eliciting the latter dose a 7-fold increase relative to saline group. Acute injection of SB-399885 produced significant CR% increments, being 1 mg/kg the most effective dose. Repeated administration (7 days) of either SB-357134 (10 mg/kg) or SB-399885 (1 mg/kg) elicited the most significant CR% increments. Moreover, modeling the potential therapeutic benefits of 5-HT6 receptor blockade, acute or repeated administration of SB-399885, at 10 mg/kg reversed memory deficits produced by scopolamine or dizocilpine, and SB-357134 (3 and 10 mg/kg) prevented amnesia and even improved performance. These data support the notion that endogenously 5-HT acting, via 5-HT6 receptor, improves memory consolidation.

CRYSTAL-QUASICHEMICAL ANALYSIS OF DEFECT SUBSYSTEM OF DOPED PbTe: Sb CRYSTALS AND Pb-Sb-Te SOLID SOLUTIONS

Directory of Open Access Journals (Sweden)

D.M. Freik

2014-05-01

Full Text Available Within crystalquasichemical formalism models of point defects of crystals in the Pb-Sb-Te system were specified. Based on proposed crystalquasichemical formulae of antimony doped crystals PbTe:Sb amphoteric dopant effect was explained. Mechanisms of solid solution formation for РbТе-Sb2Те3: replacement of antimony ions lead sites  with the formation of cation vacancies  (I or neutral interstitial tellurium atoms  (II were examined. Dominant point defects in doped crystals PbTe:Sb and РbТе-Sb2Те3 solid solutions based on p-PbTe were defined. Dependences of concentration of dominant point defects, current carriers and Hall concentration on content of dopant compound and the initial deviation from stoichiometry in the basic matrix were calculated.

A Summary of Properties Used to Evaluate INEEL Calcine Disposal in the Yucca Mountain Repository

International Nuclear Information System (INIS)

Dahl, C.A.

2003-01-01

To support evaluations of the direct disposal of Idaho National Engineering and Environmental Laboratory calcines to the repository at Yucca Mountain, an evaluation of the performance of the calcine in the repository environment must be performed. This type of evaluation demonstrates, through computer modeling and analysis, the impact the calcine would have on the ability of the repository to perform its function of containment of materials during the repository lifetime. This report discusses parameters that were used in the scoping evaluation conducted in FY 2003. It provides nominal values for the parameters, with explanation of the source of the values, and how the values were modified for use in repository analysis activities

Characterization of norm sources in petroleum coke calcining processes - 16314

International Nuclear Information System (INIS)

Hamilton, Ian S.; Halter, Donald A.; Fruchtnicht, Erich H.; Arno, Matthew G.; Haumann, Donald F

2009-01-01

Petroleum coke, or 'petcoke', is a waste by-product of the oil refining industry. The majority of petcoke consumption is in energy applications; catalyst coke is used as refinery fuel, anode coke for electricity conduction, and marketable coke for heating cement kilns. Roskill has predicted that long-term growth in petroleum coke production will be maintained, and may continue to increase slightly through 2012. Petcoke must first be calcined to drive off any undesirable petroleum by-products that would shorten the coke product life cycle. As an example, the calcining process can take place in large, rotary kilns heated to maximum temperatures as high as approximately 1400-1540 deg. C. The kilns and combustion/settling chambers, as well as some cooler units, are insulated with refractory bricks and other, interstitial materials, e.g., castable refractory materials, to improve the efficiency of the calcining process. The bricks are typically made of 70-85-percent bauxite, and are slowly worn away by the calcining process; bricks used to line the combustion chambers wear away, as well, but at a slower rate. It has been recognized that the refractory materials contain slight amounts of naturally occurring radioactive materials (NORM) from the uranium- and thorium-decay series. Similarly, low levels of NORM could be present in the petcoke feed stock given the nature of its origin. Neither the petcoke nor the refractory bricks represent appreciable sources of radiation or radioactive waste. However, some of the demolished bricks that have been removed from service because of the aforementioned wearing process have caused portal alarms to activate at municipal disposal facilities. This has lead to the current investigation into whether there is a NORM concentrating mechanism facilitated by the presence of the slightly radioactive feed stock in the presence of the slightly radioactive refractory materials, at calcining-zone temperatures. Research conducted to date has been

Simultaneous removal of Cd(II) and Sb(V) by Fe–Mn binary oxide: Positive effects of Cd(II) on Sb(V) adsorption

Energy Technology Data Exchange (ETDEWEB)

Liu, Ruiping [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); Liu, Feng [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Hu, Chengzhi, E-mail: czhu@rcees.ac.cn [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); He, Zan [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Liu, Huijuan; Qu, Jiuhui [Key Laboratory of Drinking Water Science and Technology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, Beijing 100085 (China)

2015-12-30

Highlights: • Fe–Mn binary oxide achieves the simultaneous removal of Cd(II) and Sb(V). • Cd(II) at above 0.25 mmol/L improves Sb(V) adsorption onto FMBO. • Cd(II) improves more significant Sb(V) adsorption than Ca{sup 2+} and Mn{sup 2+}. • Sb(V) adsorption decreases whereas Cd(II) adsorption increases with elevated pH. • The increased ζ-potential and Cd(II)–Sb(V) precipitation favors Sb(V) adsorption. - Abstract: The coexistence of cadmium ion (Cd(II)) and antimonate (Sb(V)) creates the need for their simultaneous removal. This study aims to investigate the effects of positively-charged Cd(II) on the removal of negative Sb(V) ions by Fe–Mn binary oxide (FMBO) and associated mechanisms. The maximum Sb(V) adsorption density (Q{sub max,Sb(V)}) increased from 1.02 to 1.32 and 2.01 mmol/g in the presence of Cd(II) at 0.25 and 0.50 mmol/L. Cd{sup 2+} exhibited a more significant positive effect than both calcium ion (Ca{sup 2+}) and manganese ion (Mn{sup 2+}). Cd{sup 2+} showed higher affinity towards FMBO and increased its ζ-potential more significantly compared to Ca{sup 2+} and Mn{sup 2+}. The simultaneous adsorption of Sb(V) and Cd(II) onto FMBO can be achieved over a wide initial pH (pH{sub i}) range from 2 to 9, and Q{sub Sb(V)} decreases whereas Q{sub Cd(II)} increases with elevated pH{sub i}. Their combined values, as expressed by Q{sub Sb(V)+Cd(II)}, amount to about 2 mmol/g and vary slightly in the pH{sub i} range 4–9. FTIR and XPS spectra indicate the significant synergistic effect of Cd(II) on Sb(V) adsorption onto FMBO, and that little chemical valence transformation occurs. These results may be valuable for the treatment of wastewater with coexisting heavy metals such as Cd(II) and Sb(V).

Talc-silicon glass-ceramic waste forms for immobilization of high- level calcined waste

International Nuclear Information System (INIS)

Vinjamuri, K.

1993-06-01

Talc-silicon glass-ceramic waste forms are being evaluated as candidates for immobilization of the high level calcined waste stored onsite at the Idaho Chemical Processing Plant. These glass-ceramic waste forms were prepared by hot isostatically pressing a mixture of simulated nonradioactive high level calcined waste, talc, silicon and aluminum metal additives. The waste forms were characterized for density, chemical durability, and glass and crystalline phase compositions. The results indicate improved density and chemical durability as the silicon content is increased

Sb(III)-Imprinted Organic-Inorganic Hybrid Sorbent Prepared by Hydrothermal-Assisted Surface Imprinting Technique for Selective Adsorption of Sb(III)

Science.gov (United States)

Zhang, Dan; Zhao, Yue; Xu, Hong-Bo

2018-03-01

Sb(III)-imprinted organic-inorganic hybrid sorbent was prepared by hydrothermal-assisted surface imprinting technique and was characterized by Fourier transform infrared spectroscopy, scanning electron microscopy coupled to an energy dispersive spectrometer and N2 adsorption/desorption isotherms. Hydrothermal-assisted process can improve the selectivity of the Sb(III)-imprinted hybrid sorbent for Sb(III) due to stable control of temperature and pressure. The Sb(III)-imprinted hybrid sorbent IIS indicated higher selectivity for Sb(III), had high static adsorption capacity of 37.3 mg g-1 for Sb(III), displayed stable adsorption capacity in pH range from 4 to 8, reached an rapid adsorption equilibrium within 30 min. According to the correlation coefficient ( r 2 > 0.99), the experimental data fitted better the pseudo-second-order kinetic model and Langmuir equilibrium isotherm.

The new Zintl phases Eu{sub 21}Cd{sub 4}Sb{sub 18} and Eu{sub 21}Mn{sub 4}Sb{sub 18}

Energy Technology Data Exchange (ETDEWEB)

Wang, Yi; Darone, Gregory M.; Bobev, Svilen, E-mail: bobev@udel.edu

2016-06-15

Crystals of two new Zintl compounds, Eu{sub 21}Mn{sub 4}Sb{sub 18} and Eu{sub 21}Cd{sub 4}Sb{sub 18} have been synthesized using the molten metal flux method, and their structures have been established by single-crystal X-ray diffraction. Both compounds are isotypic and crystallize in the monoclinic space group C2/m (No. 12, Z=4). The structures are based on edge- and corner-shared MnSb{sub 4} or CdSb{sub 4} tetrahedra, which make octameric [Mn{sub 8}Sb{sub 22}] or [Cd{sub 8}Sb{sub 22}] polyanions. Homoatomic Sb–Sb bonds are present in both structures. The Eu atoms take the role of Eu{sup 2+}cations with seven unpaired 4f electrons, as suggested by the temperature-dependent magnetization measurements. The magnetic susceptibilities of Eu{sub 21}Mn{sub 4}Sb{sub 18} and Eu{sub 21}Cd{sub 4}Sb{sub 18} indicate that both phases order anti-ferromagnetically with Néel temperatures of ca. 7 K and ca. 10 K, respectively. The unpaired 3d electrons of the Mn atoms in Eu{sub 21}Mn{sub 4}Sb{sub 18} do contribute to the magnetic response, however, the bulk magnetization measurements do not provide evidence for long-range ordering of the Mn spins down to 5 K. Electrical resistivity measurements suggest that both compounds are narrow band gap semiconductors. - Graphical abstract: Eu{sub 21}Mn{sub 4}Sb{sub 18} and Eu{sub 21}Cd{sub 4}Sb{sub 18} have complex monoclinic structures, based on MnSb{sub 4} and CdSb{sub 4} tetrahedra, both edge- and corner-shared. A perspective of the crystal structure is shown, as viewed along the b axis. Display Omitted - Highlights: • Eu{sub 21}Mn{sub 4}Sb{sub 18} and Eu{sub 21}Cd{sub 4}Sb{sub 18} are novel compounds in the respective ternary phase diagrams. • For both structures, the Zintl-Klemm rules are followed, and both are small gap semiconductors. • Eu{sub 21}Mn{sub 4}Sb{sub 18} and Eu{sub 21}Cd{sub 4}Sb{sub 18} are air-stable Zintl phases and could be new thermoelectric materials.

AgSbSe{sub 2} and AgSb(S,Se){sub 2} thin films for photovoltaic applications

Energy Technology Data Exchange (ETDEWEB)

Garza, J.G. [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon, San Nicolas de los Garza, Nuevo Leon (Mexico); Shaji, S. [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon, San Nicolas de los Garza, Nuevo Leon (Mexico); Facultad de Ingenieria Mecanica y Electrica, CIIDIT - Universidad Autonoma de Nuevo Leon, Apodaca, Nuevo Leon (Mexico); Rodriguez, A.C.; Das Roy, T.K. [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon, San Nicolas de los Garza, Nuevo Leon (Mexico); Krishnan, B., E-mail: kbindu_k@yahoo.com [Facultad de Ingenieria Mecanica y Electrica, Universidad Autonoma de Nuevo Leon, San Nicolas de los Garza, Nuevo Leon (Mexico); Facultad de Ingenieria Mecanica y Electrica, CIIDIT - Universidad Autonoma de Nuevo Leon, Apodaca, Nuevo Leon (Mexico)

2011-10-01

Silver antimony selenide (AgSbSe{sub 2}) thin films were prepared by heating sequentially deposited multilayers of antimony sulphide (Sb{sub 2}S{sub 3}), silver selenide (Ag{sub 2}Se), selenium (Se) and silver (Ag). Sb{sub 2}S{sub 3} thin film was prepared from a chemical bath containing SbCl{sub 3} and Na{sub 2}S{sub 2}O{sub 3}, Ag{sub 2}Se from a solution containing AgNO{sub 3} and Na{sub 2}SeSO{sub 3} and Se thin films from an acidified solution of Na{sub 2}SeSO{sub 3}, at room temperature on glass substrates. Ag thin film was deposited by thermal evaporation. The annealing temperature was 350 deg. C in vacuum (10{sup -3} Torr) for 1 h. X-ray diffraction analysis showed that the thin films formed were polycrystalline AgSbSe{sub 2} or AgSb(S,Se){sub 2} depending on selenium content in the precursor films. Morphology and elemental analysis of these films were done using scanning electron microscopy and energy dispersive X-ray spectroscopy. Optical band gap was evaluated from the UV-visible absorption spectra of these films. Electrical characterizations were done using Hall effect and photocurrent measurements. A photovoltaic structure: glass/ITO/CdS/AgSbSe{sub 2}/Al was formed, in which CdS was deposited by chemical bath deposition. J-V characteristics of this structure showed V{sub oc} = 435 mV and J{sub sc} = 0.08 mA/cm{sup 2} under illumination using a tungsten halogen lamp. Preparation of a photovoltaic structure using AgSbSe{sub 2} as an absorber material by a non-toxic selenization process is achieved.

Thermodynamic stability studies of Ce-Sb compounds with Fe

Science.gov (United States)

Xie, Yi; Zhang, Jinsuo; Benson, Michael T.; Mariani, Robert D.

2018-02-01

Lanthanide fission products can migrate to the fuel periphery and react with cladding, causing fuel-cladding chemical interaction (FCCI). Adding a fuel additive dopant, such as Sb, can bind lanthanide, such as Ce, into metallic compounds and thus prevent migration. The present study focuses on the thermodynamic stability of Ce-Sb compounds when in contact with the major cladding constituent Fe by conducting diffusion couple tests. Ce-Sb compounds have shown high thermodynamic stability as they did not react with Fe. When Fe-Sb compounds contacted with Ce, Sb was separated out of Fe-Sb compounds and formed the more stable Ce-Sb compounds.

A parametric study of a solar calcinator using computational fluid dynamics

International Nuclear Information System (INIS)

Fidaros, D.K.; Baxevanou, C.A.; Vlachos, N.S.

2007-01-01

In this work a horizontal rotating solar calcinator is studied numerically using computational fluid dynamics. The specific solar reactor is a 10 kW model designed and used for efficiency studies. The numerical model is based on the solution of the Navier-Stokes equations for the gas flow, and on Lagrangean dynamics for the discrete particles. All necessary mathematical models were developed and incorporated into a computational fluid dynamics model with the influence of turbulence simulated by a two-equation (RNG k-ε) model. The efficiency of the reactor was calculated for different thermal inputs, feed rates, rotational speeds and particle diameters. The numerically computed degrees of calcination compared well with equivalent experimental results

Effect of calcination temperature on the synthesis of potassium titanate with platy morphology

International Nuclear Information System (INIS)

Farina, R.; Fredericci, C.; Yoshimura, H.N.

2011-01-01

The dramatic increases in the number of pneumoconiosis cases have stimulated the search of new materials for replacement of asbestos fibers. Titanate plates with formula A y Ti 2-x M x O 4 , where A = K, Rb, Cs and M = Li, Mg, Co, Ni, Cu, Zn, Mn (III), Fe (III) have been studied as an alternative for the use of fibers. The effect of the variation of calcination temperature on the reaction of K 2 CO 3 -TiO 2 -Mg(OH) 2 system was studied with the aim of understanding the relationship of this parameter with the morphology and symmetry of the obtained plates. For this study the samples were calcined for 5 hours at temperatures of 950°C, 1000°C, 1050°C and 1100°C. The powders were analyzed by X-ray diffraction and scanning electron microscopy. It was concluded that 1000°C is the better calcination temperature for obtaining more symmetric plates with smaller particle size dispersion. (author)

Mobile calcination and cementation unit for solidification of concentrated radioactive wastes

International Nuclear Information System (INIS)

Napravnik, J.; Sazavsky, P.; Skaba, V.; Skvarenina, R.; Ditl, P.

1985-01-01

Mobile experimental unit MESA-1 was developed and manufactured for processing radioactive concentrates by direct cementation. The unit is mainly designed for processing low-level liquid wastes from nuclear power plants and other nuclear installations, in which the level of radioactivity does not exceed 10 10 Bq/m 3 , the salt content of liquid solutions does not exceed 500 kg/m 3 and the maximum amount of boric acid is 130 kg/m 3 . The equipment is built into three modules which may be assembled and dismantled in a short time and transported separately. The unit without the calciner module was tested in non-radioactive mode and in operation with actual radioactive wastes from the V-1 nuclear power plant. The course and results of the tests are described in detail. All project design values were achieved, a total of 18 dm 3 model solutions were processed and 1 m 3 of actual wastes with a salt content of 450 kg/m 3 . The test showed that with regard to the radiation level reached it will be necessary in the process of calcination to increase the shielding of certain exposed points. The calciner module is being assembled for completion. (Z.M.)

New Insights into the Origins of Sb-Induced Effects on Self-Catalyzed GaAsSb Nanowire Arrays.

Science.gov (United States)

Ren, Dingding; Dheeraj, Dasa L; Jin, Chengjun; Nilsen, Julie S; Huh, Junghwan; Reinertsen, Johannes F; Munshi, A Mazid; Gustafsson, Anders; van Helvoort, Antonius T J; Weman, Helge; Fimland, Bjørn-Ove

2016-02-10

Ternary semiconductor nanowire arrays enable scalable fabrication of nano-optoelectronic devices with tunable bandgap. However, the lack of insight into the effects of the incorporation of Vy element results in lack of control on the growth of ternary III-V(1-y)Vy nanowires and hinders the development of high-performance nanowire devices based on such ternaries. Here, we report on the origins of Sb-induced effects affecting the morphology and crystal structure of self-catalyzed GaAsSb nanowire arrays. The nanowire growth by molecular beam epitaxy is changed both kinetically and thermodynamically by the introduction of Sb. An anomalous decrease of the axial growth rate with increased Sb2 flux is found to be due to both the indirect kinetic influence via the Ga adatom diffusion induced catalyst geometry evolution and the direct composition modulation. From the fundamental growth analyses and the crystal phase evolution mechanism proposed in this Letter, the phase transition/stability in catalyst-assisted ternary III-V-V nanowire growth can be well explained. Wavelength tunability with good homogeneity of the optical emission from the self-catalyzed GaAsSb nanowire arrays with high crystal phase purity is demonstrated by only adjusting the Sb2 flux.

Influence of calcined mud on the mechanical properties and shrinkage of self-compacting concrete

Directory of Open Access Journals (Sweden)

Fatima Taieb

2018-01-01

Full Text Available The use of SCC has a particular interest in terms of sustainable development. Indeed, their specific formulation leads to a greater volume of dough than for common concretes, thus, a larger quantity of cement. However, for economical, ecological and technical reasons, it is sought to limit their cement content [1]. It is therefore necessary to almost always use mineral additions as a partial replacement for cement because the technology of self-compacting concretes can consume large quantities of fines, in this case calcinated mud issued from dams dredging sediments that can give and/or ameliorate characteristics and performances of this type of concretes. Four SCCs had been formulated from the same composition where the only percentage of calcinated mud of Chorfa (west of Algeria dam changed (0%, 10%, 20% and 30%. The effect of calcinated mud on characteristics at fresh state of SCC according to AFGC was quantified. Mechanical strengths and shrinkage deformation (total, autogenous, drying were evaluated. The results show the possibility to make SCCs with different dosages of calcinated mud having strengths that can defy those of the control SCC. The analysis of free deformations indicates the beneficial impact of the mud by contributing to decrease the amplitudes of the shrinkage compared to those of the control SCC.

Grain boundary engineering with nano-scale InSb producing high performance InxCeyCo4Sb12+z skutterudite thermoelectrics

Directory of Open Access Journals (Sweden)

Han Li

2017-12-01

Full Text Available Thermoelectric semiconductors based on CoSb3 hold the best promise for recovering industrial or automotive waste heat because of their high efficiency and relatively abundant, lead-free constituent elements. However, higher efficiency is needed before thermoelectrics reach economic viability for widespread use. In this study, n-type InxCeyCo4Sb12+z skutterudites with high thermoelectric performance are produced by combining several phonon scattering mechanisms in a panoscopic synthesis. Using melt spinning followed by spark plasma sintering (MS-SPS, bulk InxCeyCo4Sb12+z alloys are formed with grain boundaries decorated with nano-phase of InSb. The skutterudite matrix has grains on a scale of 100–200 nm and the InSb nano-phase with a typical size of 5–15 nm is evenly dispersed at the grain boundaries of the skutterudite matrix. Coupled with the presence of defects on the Sb sublattice, this multi-scale nanometer structure is exceptionally effective in scattering phonons and, therefore, InxCeyCo4Sb12/InSb nano-composites have very low lattice thermal conductivity and high zT values reaching in excess of 1.5 at 800 K.

Geological and anthropogenic factors influencing mercury speciation in mine wastes: An EXAFS spectroscopy study

Science.gov (United States)

Kim, C.S.; Rytuba, J.J.; Brown, Gordon E.

2004-01-01

The speciation of Hg is a critical determinant of its mobility, reactivity, and potential bioavailability in mine-impacted regions. Furthermore, Hg speciation in these complex natural systems is influenced by a number of physical, geological, and anthropogenic variables. In order to investigate the degree to which several of these variables may affect Hg speciation, extended X-ray absorption fine structure (EXAFS) spectroscopy was used to determine the Hg phases and relative proportions of these phases present in Hg-bearing wastes from selected mine-impacted regions in California and Nevada. The geological origin of Hg ore has a significant effect on Hg speciation in mine wastes. Specifically, samples collected from hot-spring Hg deposits were found to contain soluble Hg-chloride phases, while such phases were largely absent in samples from silica-carbonate Hg deposits; in both deposit types, however, Hg-sulfides in the form of cinnabar (HgS, hex.) and metacinnabar (HgS, cub.) dominate. Calcined wastes in which Hg ore was crushed and roasted in excess of 600??C, contain high proportions of metacinnabar while the main Hg-containing phase in unroasted waste rock samples from the same mines is cinnabar. The calcining process is thought to promote the reconstructive phase transformation of cinnabar to metacinnabar, which typically occurs at 345??C. The total Hg concentration in calcines is strongly correlated with particle size, with increases of nearly an order of magnitude in total Hg concentration between the 500-2000 ??m and process, identified the presence of Hg-sulfides and schuetteite (Hg3O2SO4), which may have formed as a result of long-term Hg(0) burial in reducing high-sulfide sediments. ?? 2003 Elsevier Ltd. All rights reserved.

GaSb solar cells grown on GaAs via interfacial misfit arrays for use in the III-Sb multi-junction cell

Science.gov (United States)

Nelson, George T.; Juang, Bor-Chau; Slocum, Michael A.; Bittner, Zachary S.; Laghumavarapu, Ramesh B.; Huffaker, Diana L.; Hubbard, Seth M.

2017-12-01

Growth of GaSb with low threading dislocation density directly on GaAs may be possible with the strategic strain relaxation of interfacial misfit arrays. This creates an opportunity for a multi-junction solar cell with access to a wide range of well-developed direct bandgap materials. Multi-junction cells with a single layer of GaSb/GaAs interfacial misfit arrays could achieve higher efficiency than state-of-the-art inverted metamorphic multi-junction cells while forgoing the need for costly compositionally graded buffer layers. To develop this technology, GaSb single junction cells were grown via molecular beam epitaxy on both GaSb and GaAs substrates to compare homoepitaxial and heteroepitaxial GaSb device results. The GaSb-on-GaSb cell had an AM1.5g efficiency of 5.5% and a 44-sun AM1.5d efficiency of 8.9%. The GaSb-on-GaAs cell was 1.0% efficient under AM1.5g and 4.5% at 44 suns. The lower performance of the heteroepitaxial cell was due to low minority carrier Shockley-Read-Hall lifetimes and bulk shunting caused by defects related to the mismatched growth. A physics-based device simulator was used to create an inverted triple-junction GaInP/GaAs/GaSb model. The model predicted that, with current GaSb-on-GaAs material quality, the not-current-matched, proof-of-concept cell would provide 0.5% absolute efficiency gain over a tandem GaInP/GaAs cell at 1 sun and 2.5% gain at 44 suns, indicating that the effectiveness of the GaSb junction was a function of concentration.

Building Planner Commitment : Are California's SB 375 and Oregon's SB 1059 Models for Climate-Change Mitigation?

Science.gov (United States)

2017-11-01

California's Sustainable Communities and Climate Protection Act (SB 375) and the Oregon Sustainable Transportation Initiative (SB 1059) have made them the first states in the nation to try and reduce greenhouse gas (GHG) emissions using the transport...

First-principles study of electronic structure of CuSbS{sub 2} and CuSbSe{sub 2} photovoltaic semiconductors

Energy Technology Data Exchange (ETDEWEB)

Maeda, T., E-mail: tmaeda@ad.ryukoku.ac.jp; Wada, T.

2015-05-01

We studied the features of CuSbS{sub 2} (CAS) and CuSbSe{sub 2} (CASe), two proposed photovoltaic compounds, and clarified their electronic structures by first-principles calculations and compared them to the chalcopyrite-type CuInSe{sub 2} results. For both CAS and CASe, the calculated enthalpies of formation of the chalcostibite phases were considerably lower than those of the chalcopyrite phases. Therefore, we considered that the chalcostibite phase is more stable for CAS and CASe. In their band structure calculated with the HSE06 hybrid functional, the valence band maxima of CAS and CASe were located at the Γ-point, and the conduction band minima were located at the R-point. Their second lowest conduction band was located at the Γ-point, whose energy level nearly equaled the R-point. For CAS (CASe), the partial density of the states shows the character of the Cu 3d and S 3p (Se 4p) orbitals at the top of the valence bands and the Sb 5p and S 3p (Se 4p) orbitals at the bottom of the conduction bands. The conduction bands of CAS and CASe have a p-orbital character (Sb 5p) that differs from the s-orbital character (In 5s) of CuInSe{sub 2}. It is for the reason that CAS and CASe do not have a chalcopyrite structure but a chalcostibite-type structure. The calculated absorption coefficient of CuSbS{sub 2} (10{sup 4}-10{sup 5} cm{sup −1}) is comparable to that of CuInSe{sub 2}. - Highlights: • We studied the features of CuSbS{sub 2} and CuSbSe{sub 2}, newly proposed photovoltaic compounds. • Chalcostibite phase is more stable in CuSbS{sub 2} and CuSbSe{sub 2}. • Band structures of CuSbS{sub 2} and CuSbS{sub 2} were calculated with HSE06 hybrid functional. • Absorption coefficient of chalcostibite-type CuSbS{sub 2} is comparable to that of CuInSe{sub 2}.

Effects upon metabolic pathways and energy production by Sb(III and As(III/Sb(III-oxidase gene aioA in Agrobacterium tumefaciens GW4.

Directory of Open Access Journals (Sweden)

Jingxin Li

Full Text Available Agrobacterium tumefaciens GW4 is a heterotrophic arsenite [As(III]/antimonite [Sb(III]-oxidizing strain. The As(III oxidase AioAB is responsible for As(III oxidation in the periplasm and it is also involved in Sb(III oxidation in Agrobacterium tumefaciens 5A. In addition, Sb(III oxidase AnoA and cellular H2O2 are also responsible for Sb(III oxidation in strain GW4. However, the deletion of aioA increased the Sb(III oxidation efficiency in strain GW4. In the present study, we found that the cell mobility to Sb(III, ATP and NADH contents and heat release were also increased by Sb(III and more significantly in the aioA mutant. Proteomics and transcriptional analyses showed that proteins/genes involved in Sb(III oxidation and resistance, stress responses, carbon metabolism, cell mobility, phosphonate and phosphinate metabolism, and amino acid and nucleotide metabolism were induced by Sb(III and were more significantly induced in the aioA mutant. The results suggested that Sb(III oxidation may produce energy. In addition, without periplasmic AioAB, more Sb(III would enter bacterial cells, however, the cytoplasmic AnoA and the oxidative stress response proteins were significantly up-regulated, which may contribute to the increased Sb(III oxidation efficiency. Moreover, the carbon metabolism was also activated to generate more energy against Sb(III stress. The generated energy may be used in Sb transportation, DNA repair, amino acid synthesis, and cell mobility, and may be released in the form of heat.

Electronic and magnetic properties of SmCrSb3 and GdCrSb3: A first principles study

International Nuclear Information System (INIS)

Sandeep; Ghimire, M.P.; Thapa, R.K.

2011-01-01

The density of states (DOS) and the magnetic moments of SmCrSb 3 and GdCrSb 3 have been studied by first principles full-potential linearized augmented plane wave (FP-LAPW) method based on density functional theory (DFT). For the exchange-correlation potential, the local-spin density approximations with correlation energy (LSDA+U) method have been used. Total and partial DOS have been computed using the WIEN2k code. DOS result shows the exchange-splittings of Cr-3d and rare-earth (R) 4f states electrons, which are responsible for the ground state ferromagnetic (FM) behavior of the systems. The FM behavior of these systems is strongly influenced by the average number of Cr-3d and Sm (Gd) 4f-electrons. The effective moment of SmCrSb 3 is found to be 7.07 μ B while for GdCrSb 3 it is 8.27 μ B . The Cr atom plays a significant role on the magnetic properties due to the hybridization between Cr-3d and Sb-5p states. - Highlights: → DOS and the magnetic moments of SmCrSb 3 and GdCrSb 3 are studied by full-FP-LAPW method. → Exchange splitting of eg and t2g of Cr-3d states and the rare-earth 4f state electrons are responsible for ground state ferromagnetism. → Rare-earth magnetic moments are greater than Cr moment indicating presence of 4f states.

Multilayer SnSb4-SbSe Thin Films for Phase Change Materials Possessing Ultrafast Phase Change Speed and Enhanced Stability.

Science.gov (United States)

Liu, Ruirui; Zhou, Xiao; Zhai, Jiwei; Song, Jun; Wu, Pengzhi; Lai, Tianshu; Song, Sannian; Song, Zhitang

2017-08-16

A multilayer thin film, comprising two different phase change material (PCM) components alternatively deposited, provides an effective means to tune and leverage good properties of its components, promising a new route toward high-performance PCMs. The present study systematically investigated the SnSb 4 -SbSe multilayer thin film as a potential PCM, combining experiments and first-principles calculations, and demonstrated that these multilayer thin films exhibit good electrical resistivity, robust thermal stability, and superior phase change speed. In particular, the potential operating temperature for 10 years is shown to be 122.0 °C and the phase change speed reaches 5 ns in the device test. The good thermal stability of the multilayer thin film is shown to come from the formation of the Sb 2 Se 3 phase, whereas the fast phase change speed can be attributed to the formation of vacancies and a SbSe metastable phase. It is also demonstrated that the SbSe metastable phase contributes to further enhancing the electrical resistivity of the crystalline state and the thermal stability of the amorphous state, being vital to determining the properties of the multilayer SnSb 4 -SbSe thin film.

Phase and morphology evolution of (Na1-xKxNbO3 powders related to calcinations and K2CO3 content

Directory of Open Access Journals (Sweden)

Steven J. Milne

2007-03-01

Full Text Available Sodium-potassium niobate ((Na1-xKxNbO3 powders with x = 0.2, 0.4, 0.6 and 0.8 were prepared following the conventional mixed oxide method and characterized by TG-DTA, XRD and SEM techniques.The effects of calcination temperature, dwell time and K2CO3 content on phase formation behavior and morphology of the powders were investigated. The calcination temperature and dwell time were found tohave a pronounced effect on the phase formation of the calcined sodium-potassium niobate powders. It was found that the crystallized phase depended on calcination conditions. The high calcination temperature andlong dwell time clearly favored particle growth and the formation of large and hard agglomerates. All the (Na1-xKxNbO3 powders showed a similar orthorhombic phase structure. The K2CO3 content significantlyaffected the calcination temperature and particle size and shape. Large particle size, cubic shape and a lower calcined condition were observed in (Na1-xKxNbO3 powder with low K2CO3 content (x = 0.2.

Behavior of GaSb (100) and InSb (100) surfaces in the presence of H{sub 2}O{sub 2} in acidic and basic cleaning solutions

Energy Technology Data Exchange (ETDEWEB)

Seo, Dongwan; Na, Jihoon; Lee, Seunghyo; Lim, Sangwoo, E-mail: swlim@yonsei.ac.kr

2017-03-31

Highlights: • Surface behavior of GaSb and InSb was investigated in acidic and basic solutions. • H{sub 2}O{sub 2} plays a key role in the surface oxidation of GaSb and InSb in acidic hydrochloric acid/hydrogen peroxide mixture (HPM) solution. • GaSb and InSb surfaces were hardly oxidized in basic ammonium hydroxide/hydrogen peroxide mixture (APM) solution in the presence of H{sub 2}O{sub 2}. • The effect of dilution of APM solution on the oxidation of the InSb surface was minimal. • Surface characteristics of GaSb and InSb in HPM and APM solutions are mainly determined by the behaviors of the group III elements rather than the group V element. - Abstract: Gallium antimonide (GaSb) and indium antimonide (InSb) have attracted strong attention as new channel materials for transistors due to their excellent electrical properties and lattice matches with various group III–V compound semiconductors. In this study, the surface behavior of GaSb (100) and InSb (100) was investigated and compared in hydrochloric acid/hydrogen peroxide mixture (HPM) and ammonium hydroxide/hydrogen peroxide mixture (APM) solutions. In the acidic HPM solution, surface oxidation was greater and the etching rates of the GaSb and InSb surfaces increased when the solution is concentrated, which indicates that H{sub 2}O{sub 2} plays a key role in the surface oxidation of GaSb and InSb in acidic HPM solution. However, the GaSb and InSb surfaces were hardly oxidized in basic APM solution in the presence of H{sub 2}O{sub 2} because gallium and indium are in the thermodynamically stable forms of H{sub 2}GaO{sub 3}{sup −} and InO{sub 2}{sup −}, respectively. When the APM solution was diluted, however, the Ga on the GaSb surface was oxidized by H{sub 2}O, increasing the etching rate. However, the effect of dilution of the APM solution on the oxidation of the InSb surface was minimal; thus, the InSb surface was less oxidized than the GaSb surface and the change in the etching rate of InSb

The crystal structure of ferdowsiite Ag8Sb4(As,Sb)4S16 and its relations to other ABX2 (A=Ag; B=As,Sb,Bi; X=S,Se) structures

DEFF Research Database (Denmark)

Makovicky, Emil; Topa, Dan

2014-01-01

arsenic. The crystal structure of ferdowsiite is a superstructure of a PbS like motif. The {100} planes of the PbS-like substructure are the (105̅), (301) and (010) planes in terms of the ferdowsiite lattice. The structure contains zig-zag chains of Sb1 connected via short Sb-S bonds and flanked by (Sb...

Restart plan for the prototype vertical denitration calciner

Energy Technology Data Exchange (ETDEWEB)

SUTTER, C.S.

1999-09-01

Testing activities on the Prototype Vertical Denitration Calciner at PFP were suspended in January 1997 due to the hold on fissile material handling in the facility. The Restart Plan will govern the transition of the test program from the completion of the activity based startup review; through equipment checkout and surrogate material runs; to resumption of the testing program and transition to unrestricted testing.

Restart plan for the prototype vertical denitration calciner

International Nuclear Information System (INIS)

SUTTER, C.S.

1999-01-01

Testing activities on the Prototype Vertical Denitration Calciner at PFP were suspended in January 1997 due to the hold on fissile material handling in the facility. The Restart Plan will govern the transition of the test program from the completion of the activity based startup review; through equipment checkout and surrogate material runs; to resumption of the testing program and transition to unrestricted testing

Role of interlayer coupling for the power factor of CuSbS2 and CuSbSe2

KAUST Repository

Alsaleh, Najebah Mohammed Abdullah; Singh, Nirpendra; Schwingenschlö gl, Udo

2016-01-01

The electronic and transport properties of bulk and monolayer CuSbS2 and CuSbSe2 are determined by using density functional theory and semiclassical Boltzmann transport theory, in order to investigate the role of interlayer coupling for the thermoelectric properties. The calculated band gaps of the bulk compounds are in agreement with experiments and significantly higher than those of the monolayers, which thus show lower Seebeck coefficients. Since also the electrical conductivity is lower, the monolayers are characterized by lower power factors. Therefore, interlayer coupling is found to be essential for the excellent thermoelectric response of CuSbS2 and CuSbSe2, even though it is weak.

Role of interlayer coupling for the power factor of CuSbS2 and CuSbSe2

KAUST Repository

Alsaleh, Najebah Mohammed Abdullah

2017-01-08

The electronic and transport properties of bulk and monolayer CuSbS2 and CuSbSe2 are determined by using density functional theory and semiclassical Boltzmann transport theory, in order to investigate the role of interlayer coupling for the thermoelectric properties. The calculated band gaps of the bulk compounds are in agreement with experiments and significantly higher than those of the monolayers, which thus show lower Seebeck coefficients. Since also the electrical conductivity is lower, the monolayers are characterized by lower power factors. Therefore, interlayer coupling is found to be essential for the excellent thermoelectric response of CuSbS2 and CuSbSe2, even though it is weak.

Role of interlayer coupling for the power factor of CuSbS2 and CuSbSe2

KAUST Repository

Alsaleh, Najebah M.

2016-09-26

The electronic and transport properties of bulk and monolayer CuSbS2 and CuSbSe2 are determined by using density functional theory and semiclassical Boltzmann transport theory, in order to investigate the role of interlayer coupling for the thermoelectric properties. The calculated band gaps of the bulk compounds are in agreement with experiments and significantly higher than those of the monolayers, which thus show lower Seebeck coefficients. Since also the electrical conductivity is lower, the monolayers are characterized by lower power factors. Therefore, interlayer coupling is found to be essential for the excellent thermoelectric response of CuSbS2 and CuSbSe2, even though it is weak.

Development and Testing of the Advanced CHP System Utilizing the Off-Gas from the Innovative Green Coke Calcining Process in Fluidized Bed

Energy Technology Data Exchange (ETDEWEB)

Chudnovsky, Yaroslav [Gas Technology Inst., Des Plaines, IL (United States); Kozlov, Aleksandr [Gas Technology Inst., Des Plaines, IL (United States)

2013-08-15

Green petroleum coke (GPC) is an oil refining byproduct that can be used directly as a solid fuel or as a feedstock for the production of calcined petroleum coke. GPC contains a high amount of volatiles and sulfur. During the calcination process, the GPC is heated to remove the volatiles and sulfur to produce purified calcined coke, which is used in the production of graphite, electrodes, metal carburizers, and other carbon products. Currently, more than 80% of calcined coke is produced in rotary kilns or rotary hearth furnaces. These technologies provide partial heat utilization of the calcined coke to increase efficiency of the calcination process, but they also share some operating disadvantages. However, coke calcination in an electrothermal fluidized bed (EFB) opens up a number of potential benefits for the production enhancement, while reducing the capital and operating costs. The increased usage of heavy crude oil in recent years has resulted in higher sulfur content in green coke produced by oil refinery process, which requires a significant increase in the calcinations temperature and in residence time. The calorific value of the process off-gas is quite substantial and can be effectively utilized as an “opportunity fuel” for combined heat and power (CHP) production to complement the energy demand. Heat recovered from the product cooling can also contribute to the overall economics of the calcination process. Preliminary estimates indicated the decrease in energy consumption by 35-50% as well as a proportional decrease in greenhouse gas emissions. As such, the efficiency improvement of the coke calcinations systems is attracting close attention of the researchers and engineers throughout the world. The developed technology is intended to accomplish the following objectives: - Reduce the energy and carbon intensity of the calcined coke production process. - Increase utilization of opportunity fuels such as industrial waste off-gas from the novel

New superconductor LaRhSb

International Nuclear Information System (INIS)

Nishigori, S.; Moriwaki, H.; Suzuki, T.; Fujita, T.; Tanaka, H.; Takabatake, T.; Fujii, H.

1994-01-01

Superconductivity in LaRhSb was newly found below the transition temperature T c = 2.67 K by the measurements of the electrical resistivity, magnetic susceptibility and specific heat in magnetic fields. The characteristics of the superconductivity determined in this study indicate that LaRhSb is a type II superconductor following the BCS theory. (orig.)

Microbiological reduction of Sb(V) in anoxic freshwater sediments

Science.gov (United States)

Oremland, Ronald S.; Kulp, Thomas R.; Miller, Laurence G.; Braiotta, Franco; Webb, Samuel M.; Kocar, Benjamin D; Blum, Jodi S.

2014-01-01

Microbiological reduction of millimolar concentrations of Sb(V) to Sb(III) was observed in anoxic sediments from two freshwater settings: (1) a Sb- and As-contaminated mine site (Stibnite Mine) in central Idaho and 2) an uncontaminated suburban lake (Searsville Lake) in the San Francisco Bay Area. Rates of Sb(V) reduction in anoxic sediment microcosms and enrichment cultures were enhanced by amendment with lactate or acetate as electron donors but not by H2, and no reduction occurred in sterilized controls. Addition of 2-14C-acetate to Stibnite Mine microcosms resulted in the production of 14CO2 coupled to Sb(V) reduction, suggesting that this process proceeds by a dissimilatory respiratory pathway in those sediments. Antimony(V) reduction in Searsville Lake sediments was not coupled to acetate mineralization and may be associated with Sb-resistance. The microcosms and enrichment cultures also reduced sulfate, and the precipitation of insoluble Sb(III)-sulfide complexes was a major sink for reduced Sb. The reduction of Sb(V) by Stibnite Mine sediments was inhibited by As(V), suggesting that As(V) is a preferred electron acceptor for the indigenous community. These findings indicate a novel pathway for anaerobic microbiological respiration and suggest that communities capable of reducing high concentrations of Sb(V) commonly occur naturally in the environment.

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

International Nuclear Information System (INIS)

COMPTON, J.A.

1999-01-01

The prototype Vertical Denitration Calciner (VDC) is installed in glovebox 188 in the Plutonium Process Support Laboratory (PPSL). Safety analysis contained in WHC-SD-CP-SAR-021 (FSAR) Rev. 0-L and Addendum to WHC-SD-CP-SAR-021, ''Laboratory Prototype Calciner'' establishes the prototype VDC needs to be shut down if a seismic event of greater than 0.07 g occurs. Shut down is to be automatic upon detection of the seismic event. This requires tie-in of various valves and power for the prototype VDC into the existing Seismic Shutdown System for the Ventilation Supply Fans described in FSAR 5.4.1.2.4. The proposed changes covered by this USQ evaluation include: (1) the physical tie-in modifications, including drawings and Engineering Change Notice (ECN), (2) the work package for accomplishing the modifications, (3) the changes to the System Description Documents, (4) the changes to the Safety Equipment List necessitated by the modifications, and (5) the changes to the failure modes and effects analysis. WHC-SDCP-OSR-010, Plutonium Finishing Plant Operational Safety Requirements Limiting Condition for Operation (LCO) 3.2.3 has been revised to include the requirement for the existing seismic shutdown system to also shut down the laboratory calciner in the event of detection of a greater than 0.07 g seismic event

Test plan for radioactive testing of a vertical direct denitration calciner

Energy Technology Data Exchange (ETDEWEB)

COMPTON, J.A.

1999-08-31

The prototype Vertical Denitration Calciner (VDC) is installed in glovebox 188 in the Plutonium Process Support Laboratory (PPSL). Safety analysis contained in WHC-SD-CP-SAR-021 (FSAR) Rev. 0-L and Addendum to WHC-SD-CP-SAR-021, ''Laboratory Prototype Calciner'' establishes the prototype VDC needs to be shut down if a seismic event of greater than 0.07 g occurs. Shut down is to be automatic upon detection of the seismic event. This requires tie-in of various valves and power for the prototype VDC into the existing Seismic Shutdown System for the Ventilation Supply Fans described in FSAR 5.4.1.2.4. The proposed changes covered by this USQ evaluation include: (1) the physical tie-in modifications, including drawings and Engineering Change Notice (ECN), (2) the work package for accomplishing the modifications, (3) the changes to the System Description Documents, (4) the changes to the Safety Equipment List necessitated by the modifications, and (5) the changes to the failure modes and effects analysis. WHC-SDCP-OSR-010, Plutonium Finishing Plant Operational Safety Requirements Limiting Condition for Operation (LCO) 3.2.3 has been revised to include the requirement for the existing seismic shutdown system to also shut down the laboratory calciner in the event of detection of a greater than 0.07 g seismic event.

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

Energy Technology Data Exchange (ETDEWEB)

COMPTON, J.A.

1999-08-31

The prototype Vertical Denitration Calciner (VDC) is installed in glovebox 188 in the Plutonium Process Support Laboratory (PPSL). Safety analysis contained in WHC-SD-CP-SAR-021 (FSAR) Rev. 0-L and Addendum to WHC-SD-CP-SAR-021, ''Laboratory Prototype Calciner'' establishes the prototype VDC needs to be shut down if a seismic event of greater than 0.07 g occurs. Shut down is to be automatic upon detection of the seismic event. This requires tie-in of various valves and power for the prototype VDC into the existing Seismic Shutdown System for the Ventilation Supply Fans described in FSAR 5.4.1.2.4. The proposed changes covered by this USQ evaluation include: (1) the physical tie-in modifications, including drawings and Engineering Change Notice (ECN), (2) the work package for accomplishing the modifications, (3) the changes to the System Description Documents, (4) the changes to the Safety Equipment List necessitated by the modifications, and (5) the changes to the failure modes and effects analysis. WHC-SDCP-OSR-010, Plutonium Finishing Plant Operational Safety Requirements Limiting Condition for Operation (LCO) 3.2.3 has been revised to include the requirement for the existing seismic shutdown system to also shut down the laboratory calciner in the event of detection of a greater than 0.07 g seismic event.

Test Plan for Radioactive Testing of a Vertical Direct Denitration Calciner

Energy Technology Data Exchange (ETDEWEB)

COMPTON, J.A.

1999-08-13

The prototype Vertical Denitration Calciner (VDC) is installed in glovebox 188 in the Plutonium Process Support Laboratory (PPSL). Safety analysis contained in WHC-SD-CP-SAR-021 (FSAR) Rev. 0-L and Addendum to WHC-SD-CP-SAR-021, ''Laboratory Prototype Calciner'' establishes the prototype VDC needs to be shut down if a seismic event of greater than 0.07 g occurs. Shut down is to be automatic upon detection of the seismic event. This requires tie-in of various valves and power for the prototype VDC into the existing Seismic Shutdown System for the Ventilation Supply Fans described in FSAR 5.4.1.2.4. The proposed changes covered by this USQ evaluation include: (1) the physical tie-in modifications, including drawings and Engineering Change Notice (ECN), (2) the work package for accomplishing the modifications, (3) the changes to the System Description Documents, (4) the changes to the Safety Equipment List necessitated by the modifications, and (5) the changes to the failure modes and effects analysis. WHC-SDCP-OSR-010, Plutonium Finishing Plant Operational Safety Requirements Limiting Condition for Operation (LCO) 3.2.3 has been revised to include the requirement for the existing seismic shutdown system to also shut down the laboratory calciner in the event of detection of a greater than 0.07 g seismic event.

Effect of calcination temperature on structural properties and photocatalytic activity of Mn-C-codoped TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Cai, Jianbo; Xin, Wei; Liu, Guanglong; Lin, Die; Zhu, Duanwei, E-mail: liugl@mail.hzau.edu.cn [Laboratory of Eco-Environmental Engineering Research, College of Resources and Environment, Huazhong Agricultural University (HZAU), Wuhan (China)

2016-03-15

Mn-C-codoped TiO{sub 2} catalysts were synthesized by modified sol-gel method based on the self-assembly technique using polyoxyethylene sorbitan monooleate (Tween 80) as template and carbon precursor and the effect of calcination temperature on their structural properties and photocatalytic activity were investigated. The XRD results showed undoped and Mn-C-codoped TiO{sub 2} calcined at 400 deg C only include anatase phase and the rutile phase appears when the calcination temperature reached to 600 deg C. UV-vis absorption spectroscopy demonstrates that the absorption spectra are strongly modified by the calcination temperature. Moreover, the Mn-C-TiO{sub 2} calcined at 400 deg C showed the lowest PL intensity due to a decrease in the recombination rate of photogenerated electrons and holes under light irradiation. The photocatalytic activity of Mn-C-codoped TiO{sub 2} were evaluated by the degradation of methyl orange (MO) under the simulate daylight irradiation and all the prepared Mn-C-codoped TiO{sub 2} samples exhibited high photocatalytic activities for photocatalytic decolorisation of methyl orange aqueous solution. At 400 deg C, the Mn-C-codoped TiO{sub 2} samples showed the highest photocatalytic activity due to synergetic effects of good crystallize ation, appropriate phase composition and slower recombination rate of photogenerated charge carriers, which further confirms the calcination temperature could affect the properties of Mn-C-codoped TiO2 significantly. (author)

Optical response of confined excitons in GaInAsSb/GaSb Quantum Dots heterostructures

Energy Technology Data Exchange (ETDEWEB)

Sanchez-Cano, R [Departamento de Fisica, Universidad Autonoma de Occidente, A.A. 2790, Cali (Colombia); Tirado-Mejia, L; Fonthal, G; Ariza-Calderon, H [Laboratorio de Optoelectronica, Universidad del Quindio, A.A. 4603 Armenia (Colombia); Porras-Montenegro, N, E-mail: rsanchez40@gmail.co [Departamento de Fisica, Universidad del Valle, A.A. 25360, Cali (Colombia)

2009-05-01

The narrow-gap Ga{sub 1-x}In{sub x}As{sub y}Sb{sub 1-y} compounds are suitable materials for heterostructure devices operating in the infrared wavelength range. In these compounds grown by liquid phase epitaxy over GaSb single crystals, for x and y values in the range of 0.10 to 0.14 for both variables, the photoluminescence optical response at 12K is blue-shifted by 20 meV related to the photoreflectance response. We believe this behavior is due to possible higher electronic confinement in some places of the heterostructure, possibly formed in the interface during the growth process. In order to explain this behavior, in this work we study the exciton recombination energy in spherical Quantum Dots (QDs) on Ga{sub 1-x}In{sub x}As{sub y}Sb{sub 1-y}/GaSb, using the variational procedure within the effective-mass approximation and considering an electron in a Type I band alignment formed by two semiconductors with similar parabolic conduction bands. Our results are in good agreement with recent experimental results.

Thermoelectric properties of ZnSb films grown by MOCVD

Energy Technology Data Exchange (ETDEWEB)

Venkatasubramanian, R; Watko, E; Colpitts, T

1997-07-01

The thermoelectric properties of ZnSb films grown by metallorganic chemical vapor deposition (MOCVD) are reported. The growth conditions necessary to obtain stoichiometric ZnSb films and the effects of various growth parameters on the electrical conductivity and Seebeck coefficients of the films are described. The as-grown ZnSb films are p-type. It was observed that the thicker ZnSb films offer improved carrier mobilities and lower free-carrier concentration levels. The Seebeck coefficient of ZnSb films was found to rise rapidly at approximately 160 C. The thicker films, due to the lower doping levels, indicate higher Seebeck coefficients between 25 to 200 C. A short annealing of the ZnSb film at temperatures of {approximately}200 C results in reduced free-carrier level. Thermal conductivity measurements of ZnSb films using the 3-{omega} method are also presented.

Electronic structure and high pressure phase transition in LaSb and CeSb

International Nuclear Information System (INIS)

Mathi Jaya, S.; Sanyal, S.P.

1992-09-01

The electronic structure and high pressure structural phase transition in cerium and lanthanum antimonides have been investigated using the tight binding LMTO method. The calculation of total energy reveals that the simple tetragonal structure is found to be stable at high pressures for both the compounds. In the case of LaSb, the calculated value of the equilibrium cell volume and the cell volume at which phase transition occurs are found to have a fairly good agreement with the experimental results. However, in the case of CeSb, the agreement is not as good as in LaSb. We also predicted the most favoured c/a value in the high pressure phase (simple tetragonal) for these compounds. Further we present the calculated results on the electronic structure of these systems at the equilibrium as well as at the reduced cell volumes. (author). 8 refs, 11 figs, 1 tab

Effect of Calcination and Reduction Temperatures on the Reduction ...

African Journals Online (AJOL)

2003-12-05

Dec 5, 2003 ... the catalyst activity. The results obtained by Rathousky et al.,9 however, revealed that the pretreatment conditions had a significant effect on the catalytic properties of Co/Al2O3 and. Co/SiO2 catalysts. Turnover frequency (TOF) for the F-T reaction decreased with increasing calcination temperature for both.

Photoluminescence and structural properties of unintentional single and double InGaSb/GaSb quantum wells grown by MOVPE

Science.gov (United States)

Ahia, Chinedu Christian; Tile, Ngcali; Botha, Johannes R.; Olivier, E. J.

2018-04-01

The structural and photoluminescence (PL) characterization of InGaSb quantum well (QW) structures grown on GaSb substrate (100) using atmospheric pressure Metalorganic Vapor Phase Epitaxy (MOVPE) is presented. Both structures (single and double-InGaSb QWs) were inadvertently formed during an attempt to grow capped InSb/GaSb quantum dots (QDs). In this work, 10 K PL peak energies at 735 meV and 740 meV are suggested to be emissions from the single and double QWs, respectively. These lines exhibit red shifts, accompanied by a reduction in their full-widths at half-maximum (FWHM) as the excitation power decreases. The presence of a GaSb spacer in the double QW was found to increase the strength of the PL emission, which consequently gives rise to a reduced blue-shift and broadening of the PL emission line observed for the double QW with an increase in laser power, while the low thermal activation energy for the quenching of the PL from the double QW is attributed to the existence of threading dislocations, as seen in the bright field TEM image for this sample.

Effects of Sb-doping on the formation of (K, Na)(Nb, Sb)O3 solid solution under hydrothermal conditions

International Nuclear Information System (INIS)

Su Likui; Zhu Kongjun; Bai Lin; Qiu Jinhao; Ji Hongli

2010-01-01

(K, Na)(Nb, Sb)O 3 (KNNS) lead-free peizoceramic powders were successfully synthesized by hydrothermal treatment at 240 o C for 8 h using the KOH, NaOH, Nb 2 O 5 and Sb 2 O 3 as raw materials. Effects of Sb-doping on the crystal structure and morphology of the as-prepared powders were investigated by powder X-ray diffraction (XRD), Raman spectra (Raman), scanning electron microscope (SEM), transmission electron microscopy (TEM) and selected area electron diffraction (SAED). The Sb element was successfully doped into the alkaline niobate perovskite structure to form crystalline (K 0.7 Na 0.3 )(Nb 0.95 Sb 0.05 )O 3 lead-free piezoelectric ceramic powder, which has a hexagonal morphology due to the aggregation growth of small grains. Phase and morphology evolutions with the reaction time were also studied, and a possible formation mechanism was proposed.

Preparation and thermal energy storage properties of paraffin/calcined diatomite composites as form-stable phase change materials

International Nuclear Information System (INIS)

Sun, Zhiming; Zhang, Yuzhong; Zheng, Shuilin; Park, Yuri; Frost, Ray L.

2013-01-01

Highlights: ► Composite phase change material (PCM) was prepared by blending composite paraffin and calcined diatomite. ► The optimum mixed proportion was obtained through differential scanning calorimetry. ► Thermal energy storage properties of the composite PCMs were determined by DSC. ► Thermal cycling test showed that the prepared PCMs are thermally reliable and chemically stable. - Abstract: A composite paraffin-based phase change material (PCM) was prepared by blending composite paraffin and calcined diatomite through the fusion adsorption method. In this study, raw diatomite was purified by thermal treatment in order to improve the adsorption capacity of diatomite, which acted as a carrier material to prepare shape-stabilized PCMs. Two forms of paraffin (paraffin waxes and liquid paraffin) with different melting points were blended together by the fusion method, and the optimum mixed proportion with a suitable phase-transition temperature was obtained through differential scanning calorimetry (DSC) analysis. Then the prepared composite paraffin was adsorbed in calcined diatomite. The prepared paraffin/calcined diatomite composites were characterized by the scanning electron microscope (SEM) and Fourier transformation infrared (FT-IR) analysis techniques. Thermal energy storage properties of the composite PCMs were determined by DSC method. DSC results showed that there was an optimum adsorption ratio between composite paraffin and calcined diatomite and the phase-transition temperature and the latent heat of the composite PCMs were 33.04 °C and 89.54 J/g, respectively. Thermal cycling test of composite PCMs showed that the prepared material is thermally reliable and chemically stable. The obtained paraffin/calcined diatomite composites have proper latent heat and melting temperatures, and show practical significance and good potential application value

Preparation and thermal energy storage properties of paraffin/calcined diatomite composites as form-stable phase change materials

Energy Technology Data Exchange (ETDEWEB)

Sun, Zhiming [School of Chemical and Environmental Engineering, China University of Mining and Technology, Beijing 100083 (China); Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, 2 George Street, GPO Box 2434, Brisbane, Queensland 4001 (Australia); Zhang, Yuzhong [School of Chemical and Environmental Engineering, China University of Mining and Technology, Beijing 100083 (China); Zheng, Shuilin, E-mail: shuilinzh@yahoo.com.cn [School of Chemical and Environmental Engineering, China University of Mining and Technology, Beijing 100083 (China); Park, Yuri [Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, 2 George Street, GPO Box 2434, Brisbane, Queensland 4001 (Australia); Frost, Ray L., E-mail: r.frost@qut.edu.au [Chemistry Discipline, Faculty of Science and Technology, Queensland University of Technology, 2 George Street, GPO Box 2434, Brisbane, Queensland 4001 (Australia)

2013-04-20

Highlights: ► Composite phase change material (PCM) was prepared by blending composite paraffin and calcined diatomite. ► The optimum mixed proportion was obtained through differential scanning calorimetry. ► Thermal energy storage properties of the composite PCMs were determined by DSC. ► Thermal cycling test showed that the prepared PCMs are thermally reliable and chemically stable. - Abstract: A composite paraffin-based phase change material (PCM) was prepared by blending composite paraffin and calcined diatomite through the fusion adsorption method. In this study, raw diatomite was purified by thermal treatment in order to improve the adsorption capacity of diatomite, which acted as a carrier material to prepare shape-stabilized PCMs. Two forms of paraffin (paraffin waxes and liquid paraffin) with different melting points were blended together by the fusion method, and the optimum mixed proportion with a suitable phase-transition temperature was obtained through differential scanning calorimetry (DSC) analysis. Then the prepared composite paraffin was adsorbed in calcined diatomite. The prepared paraffin/calcined diatomite composites were characterized by the scanning electron microscope (SEM) and Fourier transformation infrared (FT-IR) analysis techniques. Thermal energy storage properties of the composite PCMs were determined by DSC method. DSC results showed that there was an optimum adsorption ratio between composite paraffin and calcined diatomite and the phase-transition temperature and the latent heat of the composite PCMs were 33.04 °C and 89.54 J/g, respectively. Thermal cycling test of composite PCMs showed that the prepared material is thermally reliable and chemically stable. The obtained paraffin/calcined diatomite composites have proper latent heat and melting temperatures, and show practical significance and good potential application value.

The effect of calcination on multi-walled carbon nanotubes produced by dc-arc discharge.

Science.gov (United States)

Pillai, Sreejarani K; Augustyn, Willem G; Rossouw, Margaretha H; McCrindle, Robert I

2008-07-01

Multi-walled carbon nanotubes were synthesized by dc-arc discharge in helium atmosphere and the effect of calcination at different temperatures ranging from 300-600 degrees C was studied in detail. The degree of degradation to the structural integrity of the multi-walled carbon nanotubes during the thermal process was studied by Raman spectroscopy, Scanning electron microscopy and High resolution transmission electron microscopy. The thermal behaviour of the as prepared and calcined samples was investigated by thermogravimetric analysis. Calcination in air at 400 degrees C for 2 hours was found to be an efficient and simple method to eliminate carbonaceous impurities from the nanotube bundles with minimal damage to the tube walls and length. The impurities were oxidized at a faster rate when compared to the nanotubes and gave good yield of about 50%. The nanotubes were observed to be damaged at temperature higher than 450 degrees C. The results show that this method is less destructive when compared liquid phase oxidation with 5 M HNO3.

Simultaneous removal of Cd(II) and Sb(V) by Fe–Mn binary oxide: Positive effects of Cd(II) on Sb(V) adsorption

International Nuclear Information System (INIS)

Liu, Ruiping; Liu, Feng; Hu, Chengzhi; He, Zan; Liu, Huijuan; Qu, Jiuhui

2015-01-01

Highlights: • Fe–Mn binary oxide achieves the simultaneous removal of Cd(II) and Sb(V). • Cd(II) at above 0.25 mmol/L improves Sb(V) adsorption onto FMBO. • Cd(II) improves more significant Sb(V) adsorption than Ca"2"+ and Mn"2"+. • Sb(V) adsorption decreases whereas Cd(II) adsorption increases with elevated pH. • The increased ζ-potential and Cd(II)–Sb(V) precipitation favors Sb(V) adsorption. - Abstract: The coexistence of cadmium ion (Cd(II)) and antimonate (Sb(V)) creates the need for their simultaneous removal. This study aims to investigate the effects of positively-charged Cd(II) on the removal of negative Sb(V) ions by Fe–Mn binary oxide (FMBO) and associated mechanisms. The maximum Sb(V) adsorption density (Q_m_a_x_,_S_b_(_V_)) increased from 1.02 to 1.32 and 2.01 mmol/g in the presence of Cd(II) at 0.25 and 0.50 mmol/L. Cd"2"+ exhibited a more significant positive effect than both calcium ion (Ca"2"+) and manganese ion (Mn"2"+). Cd"2"+ showed higher affinity towards FMBO and increased its ζ-potential more significantly compared to Ca"2"+ and Mn"2"+. The simultaneous adsorption of Sb(V) and Cd(II) onto FMBO can be achieved over a wide initial pH (pH_i) range from 2 to 9, and Q_S_b_(_V_) decreases whereas Q_C_d_(_I_I_) increases with elevated pH_i. Their combined values, as expressed by Q_S_b_(_V_)_+_C_d_(_I_I_), amount to about 2 mmol/g and vary slightly in the pH_i range 4–9. FTIR and XPS spectra indicate the significant synergistic effect of Cd(II) on Sb(V) adsorption onto FMBO, and that little chemical valence transformation occurs. These results may be valuable for the treatment of wastewater with coexisting heavy metals such as Cd(II) and Sb(V).

Sorption-desorption of antimony species onto calcined hydrotalcite: Surface structure and control of competitive anions.

Science.gov (United States)

Constantino, Leonel Vinicius; Quirino, Juliana Nunes; Abrão, Taufik; Parreira, Paulo Sérgio; Urbano, Alexandre; Santos, Maria Josefa

2018-02-15

Calcined hydrotalcite can be applied to remove anionic contaminants from aqueous systems such as antimony species due to its great anion exchange capacity and high surface area. Hence, this study evaluated antimonite and antimonate sorption-desorption processes onto calcined hydrotalcite in the presence of nitrate, sulfate and phosphate. Sorption and desorption experiments of antimonite and antimonate were carried out in batch equilibrium and the post-sorption solids were analyzed by X-ray fluorescence (EDXRF). Sorption data were better fitted by dual-mode Langmuir-Freundlich model (R 2 >0.99) and desorption data by Langmuir model. High maximum sorption capacities were found for the calcined hydrotalcite, ranging from 617 to 790meqkg -1 . The competing anions strongly affected the antimony sorption. EDXRF analysis and mathematical modelling showed that sulfate and phosphate presented higher effect on antimonite and antimonate sorption, respectively. High values for sorption efficiency (SE=99%) and sorption capacity were attributed to the sorbent small particles and the large surface area. Positive hysteresis indexes and low mobilization factors (MF>3%) suggest very low desorption capacity to antimony species from LDH. These calcined hydrotalcite characteristics are desirable for sorption of antimony species from aqueous solutions. Copyright © 2017. Published by Elsevier B.V.

Effect of the rate of calcination of kaolin on the properties of metakaolin-based geopolymers

Directory of Open Access Journals (Sweden)

B.B. Kenne Diffo

2015-03-01

Full Text Available Kaolin samples of the same mass were treated at 700 °C for the same duration of 30 min by varying the rate of calcination (1, 2.5, 5, 10, 15 and 20 °C/min in order to obtain metakaolins which were used to produce geopolymers. Depending on the nature of each type of material, kaolin, metakaolins and geopolymers were characterized using thermal analysis, chemical analysis, XRD, FTIR, particle size distribution, specific surface area, bulk density, setting time and compressive strength. FTIR and XRD analyses showed that metakaolins except at 1 °C/min contained residual kaolinite whose quantity increased with the rate of calcination of kaolin and which influenced the characteristics of geopolymers. Thus as the rate of calcination of kaolin increased, the setting time increased (226 min (rate of 1 °C/min–773 min (rate of 20 °C/min while the compressive strength reduced (49.4 MPa (rate of 1 °C/min–20.8 MPa (rate of 20 °C/min. From the obtained results the production of geopolymers having high compressive strength along with low setting time requires that the calcination of kaolin be carried out at a low rate.

Thermoelectric and mechanical properties of spark plasma sintered Cu3SbSe3 and Cu3SbSe4: Promising thermoelectric materials

Science.gov (United States)

Tyagi, Kriti; Gahtori, Bhasker; Bathula, Sivaiah; Toutam, Vijaykumar; Sharma, Sakshi; Singh, Niraj Kumar; Dhar, Ajay

2014-12-01

We report the synthesis of thermoelectric compounds, Cu3SbSe3 and Cu3SbSe4, employing the conventional fusion method followed by spark plasma sintering. Their thermoelectric properties indicated that despite its higher thermal conductivity, Cu3SbSe4 exhibited a much larger value of thermoelectric figure-of-merit as compared to Cu3SbSe3, which is primarily due to its higher electrical conductivity. The thermoelectric compatibility factor of Cu3SbSe4 was found to be ˜1.2 as compared to 0.2 V-1 for Cu3SbSe3 at 550 K. The results of the mechanical properties of these two compounds indicated that their microhardness and fracture toughness values were far superior to the other competing state-of-the-art thermoelectric materials.

Radiation-modified structure of Ge25Sb15S60 and Ge35Sb5S60 glasses

International Nuclear Information System (INIS)

Kavetskyy, T.; Shpotyuk, O.; Kaban, I.; Hoyer, W.

2008-01-01

Atomic structures of Ge 25 Sb 15 S 60 and Ge 35 Sb 5 S 60 glasses are investigated in the γ-irradiated and annealed after γ-irradiation states by means of high-energy synchrotron x-ray diffraction technique. The first sharp diffraction peak (FSDP) is detected at around 1.1 A -1 in the structure factors of both alloys studied. The FSDP position is found to be stable for radiation/annealing treatment of the samples, while the FSDP intensity shows some changes between γ-irradiated and annealed states. The peaks in the pair distribution functions observed between 2 and 4 A are related to the Ge-S, Ge-Sb, and Sb-Sb first neighbor correlations and Ge-Ge second neighbor correlations in the edge-shared GeS 4/2 tetrahedra, and S-S and/or Ge-Ge second neighbor correlations in the corner-shared GeS 4/2 tetrahedra. Three mechanisms of the radiation-/annealing-induced changes are discussed in the framework of coordination topological defect formation and bond-free solid angle concepts

Effects of Radiative Recombination and Photon Recycling on Minority Carrier Lifetime in Epitaxial GaINAsSb Lattice-matched to GaSb

International Nuclear Information System (INIS)

S Anikeev; D Donetsky; G Belenky; S Luryl; CA Wang; DA Shiau; M Dashiell; J Beausang; G Nichols

2004-01-01

Radiative coefficient (B) is a fundamental recombination parameter which is of importance for a variety of optoelectronic minority carrier devices. Radiative recombination was comprehensively studied for wide-bandgap III-V compounds, while for 0.5-0.6 eV materials experimental data are quite limited and demonstrate significant spreading. Here we report excess carrier lifetime in isotype double heterostructures (DHs) of 0.54-eV p-GaInAsSb capped with p-AlGaAsSb, and grown lattice-matched to GaSb. Lifetime was measured by time-resolved photoluminescence (dynamic lifetime) as well as by optical response to sinusoidal excitation (static lifetime). Wide range of GaInAsSb layer thickness was used to separate contributions from interface and radiative recombination processes. Radiative coefficient and recombination velocity at GaInAsSb/AlGaAsSb heterointerface were determined. Temperature dependence of lifetime demonstrated significant contribution of radiative effects to the total recombination

Unusual crystallization behavior in Ga-Sb phase change alloys

Directory of Open Access Journals (Sweden)

Magali Putero

2013-12-01

Full Text Available Combined in situ X-ray scattering techniques using synchrotron radiation were applied to investigate the crystallization behavior of Sb-rich Ga-Sb alloys. Measurements of the sheet resistance during heating indicated a reduced crystallization temperature with increased Sb content, which was confirmed by in situ X-ray diffraction. The electrical contrast increased with increasing Sb content and the resistivities in both the amorphous and crystalline phases decreased. It was found that by tuning the composition between Ga:Sb = 9:91 (in at.% and Ga:Sb = 45:55, the change in mass density upon crystallization changes from an increase in mass density which is typical for most phase change materials to a decrease in mass density. At the composition of Ga:Sb = 30:70, no mass density change is observed which should be very beneficial for phase change random access memory (PCRAM applications where a change in mass density during cycling is assumed to cause void formation and PCRAM device failure.

Optical and structural properties of MOVPE-grown GaInSb/GaSb quantum wells

Energy Technology Data Exchange (ETDEWEB)

Wagener, Viera, E-mail: viera.wagener@nmmu.ac.z [Physics Department, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth 6031 (South Africa); Olivier, E.J.; Botha, J.R. [Physics Department, Nelson Mandela Metropolitan University, PO Box 77000, Port Elizabeth 6031 (South Africa)

2009-12-15

This paper reports on the optical and structural properties of strained type-I Ga{sub 1-x}In{sub x}Sb quantum wells embedded in GaSb from a metal-organic vapour phase epitaxial growth perspective. Photoluminescence measurements and transmission electron microscopy were used to evaluate the effect of the growth temperature on the quality of Ga{sub 1-x}In{sub x}Sb strained layers with varied alloy compositions and thicknesses. Although the various factors contributing to the overall quality of the strained layers are difficult to separate, the quantum well characteristics are significantly altered by the growth temperature. Despite the high growth rates (approx2 nm/s), quantum wells grown at 607 deg. C display photoluminescence emissions with full-width at half-maximum of 3.5-5.0 meV for an indium solid content (x) up to 0.15.

Optical and structural properties of MOVPE-grown GaInSb/GaSb quantum wells

International Nuclear Information System (INIS)

Wagener, Viera; Olivier, E.J.; Botha, J.R.

2009-01-01

This paper reports on the optical and structural properties of strained type-I Ga 1-x In x Sb quantum wells embedded in GaSb from a metal-organic vapour phase epitaxial growth perspective. Photoluminescence measurements and transmission electron microscopy were used to evaluate the effect of the growth temperature on the quality of Ga 1-x In x Sb strained layers with varied alloy compositions and thicknesses. Although the various factors contributing to the overall quality of the strained layers are difficult to separate, the quantum well characteristics are significantly altered by the growth temperature. Despite the high growth rates (∼2 nm/s), quantum wells grown at 607 deg. C display photoluminescence emissions with full-width at half-maximum of 3.5-5.0 meV for an indium solid content (x) up to 0.15.

Physics of bandgap formation in Cu-Sb-Se based novel thermoelectrics: the role of Sb valency and Cu d levels.

Science.gov (United States)

Do, Dat; Ozolins, Vidvuds; Mahanti, S D; Lee, Mal-Soon; Zhang, Yongsheng; Wolverton, C

2012-10-17

In this paper we discuss the results of ab initio electronic structure calculations for Cu(3)SbSe(4) (Se4) and Cu(3)SbSe(3) (Se3), two narrow bandgap semiconductors of thermoelectric interest. We find that Sb is trivalent in both the compounds, in contrast to a simple nominal valence (ionic) picture which suggests that Sb should be 5 + in Se4. The gap formation in Se4 is quite subtle, with hybridization between Sb 5s and the neighboring Se 4s, 4p orbitals, position of Cu d states, and non-local exchange interaction, each playing significant roles. Thermopower calculations show that Se4 is a better p-type system. Our theoretical results for Se4 agree very well with recent experimental results obtained by Skoug et al (2011 Sci. Adv. Mater. 3 602).

GaSb and GaSb/AlSb Superlattice Buffer Layers for High-Quality Photodiodes Grown on Commercial GaAs and Si Substrates

Science.gov (United States)

Gutiérrez, M.; Lloret, F.; Jurczak, P.; Wu, J.; Liu, H. Y.; Araújo, D.

2018-05-01

The objective of this work is the integration of InGaAs/GaSb/GaAs heterostructures, with high indium content, on GaAs and Si commercial wafers. The design of an interfacial misfit dislocation array, either on GaAs or Si substrates, allowed growth of strain-free devices. The growth of purposely designed superlattices with their active region free of extended defects on both GaAs and Si substrates is demonstrated. Transmission electron microscopy technique is used for the structural characterization and plastic relaxation study. In the first case, on GaAs substrates, the presence of dopants was demonstrated to reduce several times the threading dislocation density through a strain-hardening mechanism avoiding dislocation interactions, while in the second case, on Si substrates, similar reduction of dislocation interactions is obtained using an AlSb/GaSb superlattice. The latter is shown to redistribute spatially the interfacial misfit dislocation array to reduce dislocation interactions.

Structure and Chemical Bond of Thermoelectric Ce-Co-Sb Skutterudites

Institute of Scientific and Technical Information of China (English)

无

2001-01-01

The correlations among composition,structure,chemical bond and thermoelectric property of skutterudites CoSb3 and CeCo5Fe3Sb12 have been studied by using density function and discrete variation (DFT-DVM) method.Three models for this study were proposed and calculated by which the "rattling" pattern was described.Model 1 is with Ce in the center,model 2 is with Ce away the center and near to Sb,and model 3 is also with Ce away the center but near to Fe.The calculated results show that in model 3,the ionic bond is the strongest,but the covalent bond is the weakest.Due to the different changes between ionic and covalent bond,there is less difference in the stability among the models 1,2 and 3.Therefore,these different models can exist at the same time,or can translate from one to another more easily.In other words,the "rattling" pattern has taken place.Unfilled model of CoSb3,without Ce and Fe,is called model 4.The covalent bond of Co-Sb or Fe-Sb in models 1,2 and 3 is weaker than that of Co-Sb in model 4,as some electrical cloud of Sb takes part in the covalent bond of Ce-Sb in the filled models.The result is consistent with the experimental result that the thermal conductivity of CeCo5Fe3Sb12 is lower than that of CoSb3,and the thermoelectric property of CeCo5Fe3Sb12 is superior to that of CoSb3.

Ferro electrical properties of GeSbTe thin films; Propiedades ferroelectricas de peliculas delgadas de GeSbTe

Energy Technology Data Exchange (ETDEWEB)

Gervacio A, J. J.; Prokhorov, E.; Espinoza B, F. J., E-mail: jgervacio@qro.cinvestav.m [IPN, Centro de Investigacion y de Estudios Avanzados, Unidad Queretaro, Libramiento Norponiente No. 2000, Juriquilla, 76230 Queretaro (Mexico)

2011-07-01

The aim of this work is to investigate and compare ferro electrical properties of thin GeSbTe films with composition Ge{sub 4}Sb{sub 1}Te{sub 5} (with well defined ferro electrical properties) and Ge{sub 2}Sb{sub 2}Te{sub 5} using impedance, optical reflection, XRD, DSc and Piezo response Force Microscopy techniques. The temperature dependence of the capacitance in both materials shows an abrupt change at the temperature corresponding to ferroelectric-paraelectric transition and the Curie-Weiss dependence. In Ge{sub 2}Sb{sub 2}Te{sub 5} films this transition corresponds to the end from a NaCl-type to a hexagonal transformation. Piezo response Force Microscopy measurements found ferroelectric domains with dimension approximately equal to the dimension of grains. (Author)

Generalized Test Plan for the Vitrification of Simulated High-Level -Waste Calcine in the Idaho National Laboratory's Bench -Scale Cold Crucible Induction Melter

International Nuclear Information System (INIS)

Maio, Vince

2011-01-01

This Preliminary Idaho National Laboratory (INL) Test Plan outlines the chronological steps required to initially evaluate the validity of vitrifying INL surrogate (cold) High-Level-Waste (HLW) solid particulate calcine in INL's Cold Crucible Induction Melter (CCIM). Its documentation and publication satisfies interim milestone WP-413-INL-01 of the DOE-EM (via the Office of River Protection) sponsored work package, WP 4.1.3, entitled 'Improved Vitrification' The primary goal of the proposed CCIM testing is to initiate efforts to identify an efficient and effective back-up and risk adverse technology for treating the actual HLW calcine stored at the INL. The calcine's treatment must be completed by 2035 as dictated by a State of Idaho Consent Order. A final report on this surrogate/calcine test in the CCIM will be issued in May 2012-pending next fiscal year funding In particular the plan provides; (1) distinct test objectives, (2) a description of the purpose and scope of planned university contracted pre-screening tests required to optimize the CCIM glass/surrogate calcine formulation, (3) a listing of necessary CCIM equipment modifications and corresponding work control document changes necessary to feed a solid particulate to the CCIM, (4) a description of the class of calcine that will be represented by the surrogate, and (5) a tentative tabulation of the anticipated CCIM testing conditions, testing parameters, sampling requirements and analytical tests. Key FY -11 milestones associated with this CCIM testing effort are also provided. The CCIM test run is scheduled to be conducted in February of 2012 and will involve testing with a surrogate HLW calcine representative of only 13% of the 4,000 m3 of 'hot' calcine residing in 6 INL Bin Sets. The remaining classes of calcine will have to be eventually tested in the CCIM if an operational scale CCIM is to be a feasible option for the actual INL HLW calcine. This remaining calcine's make-up is HLW containing

Volatilisation of ruthenium in vitrification. Isothermal calcination studies of 'Magnox' and thermal oxide simulates

International Nuclear Information System (INIS)

Cains, P.W.; Hay, D.A.

1982-12-01

Ru volatilities have been measured for the static, isothermal calcination of ''Magnox'' and Thermal Oxide HAL's (Highly Active Liquors) at temperatures up to 600 0 C. Model solutions containing Ru, HNO 3 , and nitrates of important individual cations have also been investigated. Experimental design was primarily based on the requirements of rotary calcination process development. The results have been interpreted in terms of a reaction model involving competition between the simple degradation of Ru(NO) complexes to RuO 2 and oxidative decomposition to volatile species (e.g. RuO 4 ). (author)

Corrosion monitoring of storage bins for radioactive calcines

International Nuclear Information System (INIS)

Hoffman, T.L.

1975-01-01

Highly radioactive liquid waste produced at the Idaho Chemical Processing Plant is calcined to a granular solid for long term storage in stainless steel bins. Corrosion evaluation of coupons withdrawn from these bins indicates excellent performance for the materials of construction of the bins. At exposure periods of up to six years the average penetration rates are 0.01 and 0.05 mils per year for Types 304 and 405 stainless steels, respectively. (auth)

Influence of calcination temperature on the zirconia microstructure synthesized by complex polymerization method (CPM): a comparative study

Energy Technology Data Exchange (ETDEWEB)

Santos, R.L.P.; Mota, F.V.; Nascimento, R.M.; Henriques, B.P.; Silva, F.S.; Assis, R. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

2016-07-01

Full text: The aim of this study was to accomplish a previous characterization of the zirconia synthesized by Complex Polymerization Method (CPM) using yttria as stabilizing agent and different calcination temperatures. The powders were crystallized at 800, 900 and 1000 °C for 2h. The structural evolution Y-TZP powders were characterized by X-Ray Diffraction (XRD) and Micro-Raman Spectroscopy. The thermal properties of the calcined pre-pyrolyzed (350 °C for 4 h), samples were investigated by simultaneous thermo analysis (TGA/DTA). After heat treatment the phase Y-TZP was obtained of a single-phase, with absence of the deleterious phases. The results show that average crystallite size of the powder synthesized with 3% of Yttria dopant, increased from 11.5 to 27.9 nm when the calcination temperature increased from 800 to 1000 °C. This behavior was observed for all specimens independent of the Yttria content. The micro-Raman indicate the presence of the tetragonal phase for all samples independent of the calcination temperature employed. (author)

Calcination of Fluorinel-sodium waste blends using sugar as a feed additive (formerly WINCO-11879)

International Nuclear Information System (INIS)

Newby, B.J.; Thomson, T.D.; O'Brien, B.H.

1992-06-01

Methods were studied for using sugar as a feed additive for converting the sodium-bearing wastes stored at the Idaho Chemical Processing Plant into granular, free flowing solids by fluidized-bed calcination at 500 degrees C. All methods studied blended sodium-bearing wastes with Fluorinel wastes but differed in the types of sugar (sucrose or dextrose) that were added to the blend. The most promising sugar additive was determined to be sucrose, since it is converted more completely to inorganic carbon than is dextrose. The effect of the feed aluminum-to-alkali metal mole ratio on calcination of these blends with sugar was also investigated. Increasing the aluminum-to-alkali metal ratio from 0.6 to 1.0 decreased the calcine product-to-fines ratio from 3.0 to 1.0 and the attrition index from 80 to 15%. Further increasing the ratio to 1.25 had no effect

Stoichiometry of the U3O8 phase formed during calcination of some uranium compounds

International Nuclear Information System (INIS)

El-Fekey, S.A.; Farah, M.Y.; Rofail, N.H.

1981-01-01

Although recent work has shown U 3 O 8 phase to be the decomposition product obtained after calcining uranyl nitrate, sulphate or ammonium uranate, neither the necessary conditions for obtaining stoichiometric U 3 O 8 nor the details of the reaction have been established. Presence of sulphate or nitrate ions during preparation greatly affects the O/U of the obtained oxides and the physico-chemical properties of uranium tetrafluoride prepared afterwards from it (1-3). The aim of the present investigation was to study the effect of calcination regimes on the stoichiometry of the U 3 O 8 phase produced by the thermal decomposition of uranyl nitrate, sulphate, and ammonium uranate, which was prepared by precipitation from nuclear-pure uranyl sulphate. Stoichiometry of the U 3 O 8 phase formed during calcination of ammonium uranate precipitated from nuclear pure uranyl nitrate solution was reported before (1)

Three-Dimensional Reduced Graphene Oxide Coupled with Mn3O4 for Highly Efficient Removal of Sb(III) and Sb(V) from Water.

Science.gov (United States)

Zou, Jian-Ping; Liu, Hui-Long; Luo, Jinming; Xing, Qiu-Ju; Du, Hong-Mei; Jiang, Xun-Heng; Luo, Xu-Biao; Luo, Sheng-Lian; Suib, Steven L

2016-07-20

Highly porous, three-dimensional (3D) nanostructured composite adsorbents of reduced graphene oxides/Mn3O4 (RGO/Mn3O4) were fabricated by a facile method of a combination of reflux condensation and solvothermal reactions and systemically characterized. The as-prepared RGO/Mn3O4 possesses a mesoporous 3D structure, in which Mn3O4 nanoparticles are uniformly deposited on the surface of the reduced graphene oxide. The adsorption properties of RGO/Mn3O4 to antimonite (Sb(III)) and antimonate (Sb(V)) were investigated using batch experiments of adsorption isotherms and kinetics. Experimental results show that the RGO/Mn3O4 composite has fast liquid transport and superior adsorption capacity toward antimony (Sb) species in comparison to six recent adsorbents reported in the literature and summarized in a table in this paper. Theoretical maximum adsorption capacities of RGO/Mn3O4 toward Sb(III) and Sb(V) are 151.84 and 105.50 mg/g, respectively, modeled by Langmuir isotherms. The application of RGO/Mn3O4 was demonstrated by using drinking water spiked with Sb (320 μg/L). Fixed-bed column adsorption experiments indicate that the effective breakthrough volumes were 859 and 633 mL bed volumes (BVs) for the Sb(III) and Sb(V), respectively, until the maximum contaminant level of 5 ppb was reached, which is below the maximum limits allowed in drinking water according to the most stringent regulations. The advantages of being nontoxic, highly stable, and resistant to acid and alkali and having high adsorption capacity toward Sb(III) and Sb(V) confirm the great potential application of RGO/Mn3O4 in Sb-spiked water treatment.

Bone mineral change during experimental calcination: an X-ray diffraction study.

Science.gov (United States)

Galeano, Sergio; García-Lorenzo, Mari Luz

2014-11-01

The effects of calcination (400-1200°C) on pig bones have been studied using powder X-ray diffraction (XRD) and secondary modifications, such as color change and weight loss. The characterisation by powder XRD confirmed the presence of the crystalline phase of hydroxyapatite, and comparison of the results obtained at different temperatures suggested that at 650°C, all the organic components and carbonate substitutions were completely removed. Accordingly, these samples were white. In addition, the crystallinity degree and the crystallite size progressively increased with the calcination temperature until 650°C, remaining stable until 1200°C. Below 650°C, bone samples presented organic compounds, resulting in background noise in the diffractogram and gray or black color. In addition, impurities in the lattice correspond to low crystallite sizes. © 2014 American Academy of Forensic Sciences.

Influence of calcination temperature in pozolanicity of gray sugar cane bagasse

International Nuclear Information System (INIS)

Santos, T.A.; Argolo, R.A.; Andrade, H.M.C.; Ribeiro, D.V.

2016-01-01

BCA (Sugar Cane Bagasse) is burned in boilers in the process of electricity cogeneration causing the generation of CBCA (Gray Sugar Cane Bagasse), which is the final residue of sucroalcooeira industry. Currently, several studies seek alternative materials that can replace Portland cement, promoting discussions on the use of pozzolanic materials in cementitious matrices. Thus, this research seeks to analyze the pozzolanicity the CBCA, obtained by calcining the residue at different temperatures, to be determined by TG / DTG and DTA tests. For analysis of pozzolanicity these ashes were used electrical conductivity techniques, chemical titration NP EN 196-5, chapelle modified NBR 15895/2010 and the IAP method (Activity Index pozzolanic NBR:5752). The results obtained during the study demostraramm no difference between the ash calcined at temperatures of 500 ° C, 600 ° C and 700 ° C. (author)

Antimony Redox Biotransformation in the Subsurface: Effect of Indigenous Sb(V) Respiring Microbiota.

Science.gov (United States)

Wang, Liying; Ye, Li; Yu, Yaqin; Jing, Chuanyong

2018-02-06

Anaerobic microbiological antimonate [Sb(V)] respiration is a newly discovered process regulating the Sb redox transformation in soils. However, little is known about the role microbiological Sb(V) respiration plays in the fate of Sb in the subsurface, especially in the presence of sulfate and electron shuttles. Herein, we successfully enriched a Sb(V) reducing microbiota (SbRM) from the subsurface near an active Sb mine. SbRM was dominated by genus Alkaliphilus (18-36%), Clostridiaceae (17-18%), Tissierella (24-27%), and Lysinibacillus (16-37%). The incubation results showed that SbRM reduced 88% of dissolved Sb(V) to Sb(III), but the total Sb mobility remained the same as in the abiotic control, indicating that SbRM alone did not increase the total Sb release but regulated the Sb speciation in the subsurface. Micro X-ray fluorescence (μ-XRF) analysis suggested the association of Sb and Fe, and electron shuttles such as anthraquinone-2,6-disulfonic disodium salt (AQDS) markedly enhanced the Sb release due to its ability to facilitate Fe mineral dissolution. Sb L-edge and S K-edge X-ray absorption near edge structure (XANES) results demonstrated that indigenous SbRM immobilized Sb via Sb 2 S 3 formation, especially in a sulfur-rich environment. The insights gained from this study shed new light on Sb mobilization and its risk assessment in the subsurface environment.

Enhanced separation efficiency of photoinduced charges for antimony-doped tin oxide (Sb-SnO{sub 2})/TiO{sub 2} heterojunction semiconductors with varied Sb doping concentration

Energy Technology Data Exchange (ETDEWEB)

Zhang, Zhen-Long [School of Physics and Electronics, Henan University, Kaifeng 475004 (China); Ma, Wen-Hai [School of Physical Education, Henan University, Kaifeng 475004 (China); Mao, Yan-Li, E-mail: ylmao1@163.com [School of Physics and Electronics, Henan University, Kaifeng 475004 (China); Institute for Computational Materials Science, Henan University, Kaifeng 475004 (China)

2014-09-07

In this paper, antimony-doped tin oxide (Sb-SnO{sub 2}) nanoparticles were synthesized with varied Sb doping concentration, and the Sb-SnO{sub 2}/TiO{sub 2} heterojunction semiconductors were prepared with Sb-SnO{sub 2} and TiO{sub 2}. The separation efficiency of photoinduced charges was characterized with surface photovoltage (SPV) technique. Compared with Sb-SnO{sub 2} and TiO{sub 2}, Sb-SnO{sub 2}/TiO{sub 2} presents an enhanced separation efficiency of photoinduced charges, and the SPV enhancements were estimated to be 1.40, 1.43, and 1.99 for Sb-SnO{sub 2}/TiO{sub 2} composed of Sb-SnO{sub 2} with the Sb doping concentration of 5%, 10%, and 15%, respectively. To understand the enhancement, the band structure of Sb-SnO{sub 2} and TiO{sub 2} in the heterojunction semiconductor was determined, and the conduction band offsets (CBO) between Sb-SnO{sub 2} and TiO{sub 2} were estimated to be 0.56, 0.64, and 0.98 eV for Sb-SnO{sub 2}/TiO{sub 2} composed of Sb-SnO{sub 2} with the Sb doping concentration of 5%, 10%, and 15%, respectively. These results indicate that the separation efficiency enhancement is resulting from the energy level matching, and the increase of enhancement is due to the rising of CBO.

Crystal structure, magnetism, {sup 89}Y solid state NMR, and {sup 121}Sb Moessbauer spectroscopic investigations of YIrSb

Energy Technology Data Exchange (ETDEWEB)

Benndorf, Christopher [Institut fuer Physikalische Chemie, Universitaet Muenster (Germany); Institut fuer Anorganische und Analytische Chemie, Universitaet Muenster (Germany); Heletta, Lukas; Block, Theresa; Poettgen, Rainer [Institut fuer Anorganische und Analytische Chemie, Universitaet Muenster (Germany); Eckert, Hellmut [Institut fuer Physikalische Chemie, Universitaet Muenster (Germany); Institute of Physics in Sao Carlos, University of Sao Paulo, Sao Carlos (Brazil)

2017-02-15

The ternary antimonide YIrSb was synthesized from the binary precursor YIr and elemental antimony by a diffusion controlled solid-state reaction. Single crystals were obtained by a flux technique with elemental bismuth as an inert solvent. The YIrSb structure (TiNiSi type, space group Pnma) was refined from single-crystal X-ray diffractometer data: a = 711.06(9), b = 447.74(5), c = 784.20(8) pm, wR{sub 2} = 0.0455, 535 F{sup 2} values, 20 variables. {sup 89}Y solid state MAS NMR and {sup 121}Sb Moessbauer spectra show single resonance lines in agreement with single-crystal X-ray data. YIrSb is a Pauli paramagnet. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

The system Sb2Te3-InS

International Nuclear Information System (INIS)

Safarov, M.G.; Gamidov, R.S.; Poladov, P.M.

1991-01-01

The system Sb 2 Te 3 -InS was investigated by the methods of physicochemical analysis. Its state diagram was constructed. It represents the stable diagonal of the mutual ternary system InTe-Sb 2 Te 3 -Sb 2 S 3 -InS. It was established that limited regions of α- and β-solid solutions on the basis of Sb 2 Te 3 and InS, achieving 15.5 and 8 mol.% respectively, formed in the system. Lattice periods of α- and β-solid solutions, their lattice volumes, number of atoms in them and densities were calculated

Role of interlayer coupling for the power factor of CuSbS2 and CuSbSe2

KAUST Repository

Alsaleh, Najebah Mohammed Abdullah; Singh, Nirpendra; Schwingenschlö gl, Udo

2017-01-01

The electronic and transport properties of bulk and monolayer CuSbS2 and CuSbSe2 are determined by using density functional theory and semiclassical Boltzmann transport theory, in order to investigate the role of interlayer coupling

Quaternary InGaAsSb Thermophotovoltaic Diode Technology

International Nuclear Information System (INIS)

M Dashiell; J Beausang; H Ehsani; G Nichols; D DePoy; L Danielson; P Talamo; K Rahner; E Brown; S Burger; P Fourspring; W Topper; P Baldasaro; C Wang; R Huang; M Connors; G Turner; Z Shellenbarger; G Taylor; Jizhong Li; R Martinelli; D Donetski; S Anikeev; G Belenky; S Luryl

2005-01-01

Thermophotovoltaic (TPV) diodes fabricated from InGaAsSb alloys lattice-matched to GaSb substrates are grown by Metal Organic Vapor Phase Epitaxy (MOVPE). 0.53eV InGaAsSb TPV diodes utilizing front-surface spectral control filters have been tested in a vacuum cavity and a TPV thermal-to-electric conversion efficiency (η TPV ) and a power density (PD) of η TPV = 19% and PD=0.58 W/cm 2 were measured for T radiator = 950 C and T diode = 27 C. Recombination coefficients deduced from minority carrier measurements and the theory reviewed in this article predict a practical limit to the maximum achievable conversion efficiency and power density for 0.53eV InGaAsSb TPV. The limits for the above operating temperatures are projected to be η TPV = 26% and PD = 0.75 W/cm 2 . These limits are extended to η TPV = 30% and PD = 0.85W/cm 2 if the diode active region is bounded by a reflective back surface to enable photon recycling and a two-pass optical path length. The internal quantum efficiency of the InGaAsSb TPV diode is close to the theoretically predicted limits, with the exception of short wavelength absorption in GaSb contact layers. Experiments show that the open circuit voltage of the 0.53eV InGaAsSb TPV diodes is not strongly dependent on the device architectures studied in this work where both N/P and P/N double heterostructure diodes have been grown with various acceptor and donor doping levels, having GaSb and AlGaAsSb confinement, and also partial back surface reflectors. Lattice matched InGaAsSb TPV diodes were fabricated with bandgaps ranging from 0.6 to 0.5eV without significant degradation of the open circuit voltage factor, quantum efficiency, or fill factor as the composition approached the miscibility gap. The key diode performance parameter which is limiting efficiency and power density below the theoretical limits in InGaAsSb TPV devices is the open circuit voltage. The open circuit voltages of state-of-the-art 0.53eV InGaAsSb TPV diode are ∼10

Effects of milling method and calcination condition on phase and morphology characteristics of Mg4Nb2O9 powders

International Nuclear Information System (INIS)

Wongmaneerung, R.; Sarakonsri, T.; Yimnirun, R.; Ananta, S.

2006-01-01

Magnesium niobate, Mg 4 Nb 2 O 9 , powders has been synthesized by a solid-state reaction. Both conventional ball- and rapid vibro-milling have been investigated as milling methods, with the formation of the Mg 4 Nb 2 O 9 phase investigated as a function of calcination conditions by DTA and XRD. The particle size distribution of the calcined powders was determined by laser diffraction technique, while morphology, crystal structure and phase composition were determined via a combination of SEM, TEM and EDX techniques. The type of milling method together with the designed calcination condition was found to show a considerable effect on the phase and morphology evolution of the calcined Mg 4 Nb 2 O 9 powders. It is seen that optimization of calcination conditions can lead to a single-phase Mg 4 Nb 2 O 9 in both milling methods. However, the formation temperature and dwell time for single-phase Mg 4 Nb 2 O 9 powders were lower with the rapid vibro-milling technique

Connecting section and associated systems concept for the spray calciner/in-can melter process

International Nuclear Information System (INIS)

Petkus, L.L.; Gorton, P.S.; Blair, H.T.

1981-06-01

For a number of years, researchers at the Pacific Northwest Laboratory have been developing processes and equipment for converting high-level liquid wastes to solid forms. One of these processes is the Spray Calciner/In-Can Melter system. To immobilize high-level liquid wastes, this system must be operated remotely, and the calcine must be reliably conveyed from the calciner to the melting furnace. A concept for such a remote conveyance system was developed at the Pacific Northwest Laboratory, and equipment was tested under full-scale, nonradioactive conditions. This concept and the design of demonstration equipment are described, and the results of equipment operation during experimental runs of 7 d are presented. The design includes a connecting section and its associated systems - a canister sypport and alignment concept and a weight-monitoring system for the melting furnace. Overall, the runs demonstrated that the concept design is an acceptable method of connecting the two pieces of process equipment together. Although the connecting section has not been optimized in all areas of concern, it provides a first-generation design of a production-oriented system

Idaho National Engineering and Environmental Laboratory, Old Waste Calcining Facility, Scoville vicinity, Butte County, Idaho -- Photographs, written historical and descriptive data. Historical American engineering record

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-12-31

This report describes the history of the Old Waste Calcining Facility. It begins with introductory material on the Idaho National Engineering and Environmental Laboratory, the Materials Testing Reactor fuel cycle, and the Idaho Chemical Processing Plant. The report then describes management of the wastes from the processing plant in the following chapters: Converting liquid to solid wastes; Fluidized bed waste calcining process and the Waste Calcining Facility; Waste calcining campaigns; WCF gets a new source of heat; New Waste Calcining Facility; Last campaign; Deactivation and the RCRA cap; Significance/context of the old WCF. Appendices contain a photo key map for HAER photos, a vicinity map and neighborhood of the WCF, detailed description of the calcining process, and chronology of WCF campaigns.

Idaho National Engineering and Environmental Laboratory, Old Waste Calcining Facility, Scoville vicinity, Butte County, Idaho -- Photographs, written historical and descriptive data. Historical American engineering record

International Nuclear Information System (INIS)

1997-01-01

This report describes the history of the Old Waste Calcining Facility. It begins with introductory material on the Idaho National Engineering and Environmental Laboratory, the Materials Testing Reactor fuel cycle, and the Idaho Chemical Processing Plant. The report then describes management of the wastes from the processing plant in the following chapters: Converting liquid to solid wastes; Fluidized bed waste calcining process and the Waste Calcining Facility; Waste calcining campaigns; WCF gets a new source of heat; New Waste Calcining Facility; Last campaign; Deactivation and the RCRA cap; Significance/context of the old WCF. Appendices contain a photo key map for HAER photos, a vicinity map and neighborhood of the WCF, detailed description of the calcining process, and chronology of WCF campaigns

Role of hydrogen in Sb film deposition and characterization of Sb and GexSby films deposited by cyclic plasma enhanced chemical vapor deposition using metal-organic precursors

International Nuclear Information System (INIS)

Kim, Hyung Keun; Jung, Jin Hwan; Choi, Doo Jin

2012-01-01

To meet increasing demands for chemical vapor deposition methods for high performance phase-change memory, cyclic plasma enhanced chemical vapor deposition of Sb and Ge x Sb y phase-change films and characterization of their properties were performed. Two cycle sequences were designed to investigate the role of hydrogen gas as a reduction gas during Sb film deposition. Hydrogen gas was not introduced into the reaction chamber during the purge step in cycle sequence A and was introduced during the purge step for cycle sequence B. The role of hydrogen gas was investigated by comparing the results obtained from these two cycle sequences and was concluded to exert an effect by a combination of precursor decomposition, surface maintenance as a hydrogen termination agent, and surface etching. These roles of hydrogen gas are discussed through consideration of changes in deposition rates, the oxygen concentration on the surface of the Sb film, and observations of film surface morphology. Based on these results, Ge x Sb y phase-change films were deposited with an adequate flow rate of hydrogen gas. The Ge and Sb composition of the film was controlled with the designed cycle sequences. A strong oxygen affinity for Ge was observed during the X-ray photoelectron spectroscopy analysis of Sb 3d, Sb 4d, and Ge 3d orbitals. Based on the XPS results, the ratios of Ge to Sb were calculated to be Ge 0.32 Sb 0.68 , Ge 0.38 Sb 0.62 , Ge 0.44 Sb 0.56 , Ge 0.51 Sb 0.49 and Ge 0.67 Sb 0.33 for the G1S7, G1S3, G1S2, G1S1, and G2S1 cycles, respectively. Crystal structures of Sb, Ge, and the GeSb metastable phase were observed with various Ge x Sb y film compositions. Sb crystallinity decreased with respect to Ge crystallinity by increasing the Ge fraction. A current–voltage curve was introduced, and an electro-switching phenomenon was clearly generated at a typical voltage, V th . V th values increased in conjunction with an increased proportion of Ge. The Sb crystallinity decrease and V

Improved structural and electrical properties in native Sb2Te3/GexSb2Te3+x van der Waals superlattices due to intermixing mitigation

Directory of Open Access Journals (Sweden)

Stefano Cecchi

2017-02-01

Full Text Available Superlattices made of Sb2Te3/GeTe phase change materials have demonstrated outstanding performance with respect to GeSbTe alloys in memory applications. Recently, epitaxial Sb2Te3/GeTe superlattices were found to feature GexSb2Te3+x blocks as a result of intermixing between constituting layers. Here we present the epitaxy and characterization of Sb2Te3/GexSb2Te3+x van der Waals superlattices, where GexSb2Te3+x was intentionally fabricated. X-ray diffraction, Raman spectroscopy, scanning transmission electron microscopy, and lateral electrical transport data are reported. The intrinsic 2D nature of both sublayers is found to mitigate the intermixing in the structures, significantly improving the interface sharpness and ultimately the superlattice structural and electrical properties.

Raman spectra of the system TeCl4-SbCl5

International Nuclear Information System (INIS)

Brockner, W.; Demiray, A.F.

1980-01-01

Raman spectra of the solid and molten TeCl 4 . SbCl 5 addition compound and of some TeCl 4 -SbCl 5 mixtures have been recorded. Two modifications of the crystalline TeCl 4 -SbCl 5 compound have been found. The structure of the melt can be described by the equilibrium TeCl 3 + + SbCl 6 - reversible TeCl 4 + SbCl 5 lying on the left side. Mixtures with other stoichiometry contain the 1:1 adduct only and excess TeCl 4 or SbCl 5 , respectively. Such melts are built up by the ionic species TeCl 3 + and SbCl 6 - also and TeCl 4 or SbCl 5 according to stoichiometry. (author)

Improvements in or relating to calcining reducible compounds

International Nuclear Information System (INIS)

Cole, E.A.; Peterson, R.S.

1974-01-01

Apparatus is described for calcining compounds of uranium compounds to temperatures of up to about 1000 0 C to produce UO 2 powders of uniform quality and having an oxygen content of less than 2.2 atoms of oxygen per atom of uranium. The apparatus comprises discharge and cooling means having an inlet end operatively joined with an air tight seal to a rotating Kiln to receive hot UO 2 powder therefrom without contact with air. (author)

New Insights into the Origins of Sb-Induced Effects on Self-Catalyzed GaAsSb Nanowire Arrays

DEFF Research Database (Denmark)

Ren, Dingding; Dheeraj, Dasa L.; Jin, Chengjun

2016-01-01

and thermodynamically by the introduction of Sb. An anomalous decrease of the axial growth rate with increased Sb2 flux is found to be due to both the indirect kinetic influence via the Ga adatom diffusion induced catalyst geometry evolution and the direct composition modulation. From the fundamental growth analyses...

Kinetic Study of Calcination of Jakura Limestone Using Power Rate ...

African Journals Online (AJOL)

The calcination of Jakura limestone was also found to be first order reaction with respect to CaCO3 concentration having average regression coefficient of 0.99. The temperature dependent terms were found using Arrhenius law and it was observed that the reaction temperature has a direct effect on the rate of reaction.

Characterisation of sugar cane straw waste as pozzolanic material for construction: Calcining temperature and kinetic parameters

International Nuclear Information System (INIS)

Frias, Moises; Villar-Cocina, E.; Valencia-Morales, E.

2007-01-01

This paper reports on the influence of calcining temperature (800 and 1000 deg. C) on the pozzolanic activation of sugar cane straw (SCS). The reaction kinetics of SCS ash-lime mixtures were inferred from physicochemical characteristics (X-ray diffraction patterns and thermogravimetry analysis. The fitting of a kinetic-diffusive model to the experimental data (fixed lime versus time) allowed the computing of the kinetic parameters (reaction rate constant) of the pozzolanic reaction. Results obtained confirm that the sugar cane straw ash (SCSA) calcined at 800 and 1000 deg. C have properties indicative of very high pozzolanic activity. No influence of calcining temperature on the pozzolanic activity was observed. Also, no crystalline compounds during the pozzolanic reaction were identified up to 90 days of reaction. Environmental durability and strength of the consequential mortars remain to be assessed

Characterization of midwave infrared InSb avalanche photodiode

Energy Technology Data Exchange (ETDEWEB)

Abautret, J., E-mail: johan.abautret@ies.univ-montp2.fr; Evirgen, A. [Université Montpellier, IES, UMR 5214, F-34095 Montpellier (France); CNRS, IES, UMR 5214, F-34095 Montpellier (France); SOFRADIR, BP 21, 38113 Veurey-Voroize (France); Perez, J. P.; Christol, P. [Université Montpellier, IES, UMR 5214, F-34095 Montpellier (France); CNRS, IES, UMR 5214, F-34095 Montpellier (France); Rothman, J. [CEA-LETI, 17 rue des Martyrs, 38054 Grenoble Cedex 9 (France); Cordat, A. [SOFRADIR, BP 21, 38113 Veurey-Voroize (France)

2015-06-28

This paper focuses on the InSb material potential for the elaboration of Avalanche Photodiodes (APD) for high performance infrared imaging applications, both in passive or active mode. The first InSb electron-APD structure was grown by molecular beam epitaxy, processed and electrically characterized. The device performances are at the state of the art for the InSb epi-diode technology, with a dark current density J(−50 mV) = 32 nA/cm{sup 2} at 77 K. Then, a pure electron injection was performed, and an avalanche gain, increasing exponentially, was observed with a gain value near 3 at −4 V at 77 K. The Okuto–Crowell model was used to determine the electron ionization coefficient α(E) in InSb, and the InSb gain behavior is compared with the one of InAs and MCT APDs.

High-Temperature Characteristics of an InAsSb/AlAsSb n+Bn Detector

Science.gov (United States)

Ting, David Z.; Soibel, Alexander; Höglund, Linda; Hill, Cory J.; Keo, Sam A.; Fisher, Anita; Gunapala, Sarath D.

2016-09-01

The high-temperature characteristics of a mid-wavelength infrared (MWIR) detector based on the Maimon-Wicks InAsSb/AlAsSb nBn architecture was analyzed. The dark current characteristics are examined in reference to recent minority carrier lifetime results. The difference between the responsivity and absorption quantum efficiency (QE) at shorter wavelengths is clarified in terms of preferential absorption of higher-energy photons in the top contact layer, which cannot provide reverse-bias photo-response due to the AlAsSb electron blocking layer and strong recombination. Although the QE does not degrade when the operating temperature increases to 325 K, the turn-on bias becomes larger at higher temperatures. This behavior was originally attributed to the change in the valence band alignment between the absorber and top contact layers caused by the shift in Fermi level with temperature. In this work, we demonstrated the inadequacy of the original description, and offer a more likely explanation based on temperature-dependent band-bending effects.

High-Temperature Release of SO2 from Calcined Cement Raw Materials

DEFF Research Database (Denmark)

Nielsen, Anders Rooma; Larsen, Morten B.; Glarborg, Peter

2011-01-01

During combustion of alternative fuels in the material inlet end of cement rotary kilns, local reducing conditions may occur and cause reductive decomposition of sulfates from calcined cement raw materials. Decomposition of sulfates is problematic because it increases the gas-phase SO2...... concentration, which may cause deposit formation in the kiln system. In this study, the release of sulfur from calcined cement raw materials under both oxidizing and reducing conditions is investigated. The investigations include thermodynamic equilibrium calculations in the temperature interval of 800–1500 °C...... and experiments in a tube furnace reactor in the temperature interval of 900–1100 °C. The investigated conditions resemble actual conditions in the material inlet end of cement rotary kilns. It was found that the sulfates CaSO4, K2SO4, and Na2SO4 were all stable under oxidizing conditions but began to decompose...

New uranium chalcoantimonates, RbU{sub 2}SbS{sub 8} and KU{sub 2}SbSe{sub 8}, with a polar noncentrosymmetric structure

Energy Technology Data Exchange (ETDEWEB)

Choi, K S; Kanatzidis, M G

1999-09-01

The new compounds, RbU{sub 2}SbS{sub 8} and KU{sub 2}SbSe{sub 8}, were prepared as golden-black, blocklike crystals by the polychalcogenide molten flux method. RbU{sub 2}SbS{sub 8} has a two-dimensional character with layers running perpendicular to the c-axis. The coordination geometry around the U{sup 4+} atoms is best described as a bicapped trigonal prism. The trigonal prisms share triangular faces with neighboring prisms, forming one-dimensional columns along the a-axis. The columns are then joined to construct sheets by sharing capping S atoms. Sb{sup 3+} ions are sitting at the center of a slightly distorted seesaw coordination environment (CN = 4). Rb{sup +} ions are stabilized in 8-coordinate bicapped trigonal prismatic sites. KU{sub 2}SbSe{sub 8} has essentially the same structure as RbU{sub 2}SbS{sub 8}. However, Sb{sup 3+} and K{sup +} ions appear disordered in every other layer resulting in a different unit cell. RbU{sub 2}SbS{sub 8} is a semiconductor with a band gap of 1.38 eV. The band gap of KU{sub 2}SbSe{sub 8} could not be determined precisely due to the presence of overlapping intense f-f transitions in the region (0.5--1.1 eV). The Raman spectra show the disulfide stretching vibration in RbU{sub 2}SbS{sub 8} at 479 cm{sup {minus}1} and the diselenide stretching vibration in KU{sub 2}SbSe{sub 8} at 252 cm{sup {minus}1}. Magnetic susceptibility measurements indicate the presence of U{sup 4+} centers in the compounds. The compounds do not melt below 1,000 C under vacuum.

A 121Sb Moessbauer Study of the Chemical State of Antimony in V-Sb-O Mixed-Oxide Catalysts for the Ammoxidation of Propane

International Nuclear Information System (INIS)

Stievano, L.; Wagner, F. E.; Zanthoff, H. W.; Calogero, S.

2002-01-01

The structural changes of two representative samples of a group of V-Sb-oxide catalysts, a vanadium-rich and an antimony-rich specimen, are investigated by 121 Sb Moessbauer spectroscopy after treatment under propene or hydrogen at 673 K. The as-prepared catalysts contain both Sb(V) and Sb(III) as crystalline and microcrystalline α-Sb 2 O 4 and VSbO 4 , as well as an additional amorphous V 5+ oxide phase. The oxidation state of antimony does not change upon exposure to propene, whereas a partial reduction can be obtained by a more intense reduction under hydrogen. The Moessbauer results indicate that the antimony in VSbO 4 can be reduced more easily than that in α-Sb 2 O 4 , which appears to be more stable. These results are discussed in view of the observed depletion of vanadium at the surface of the catalyst particles under reaction conditions.

Improved structural and electrical properties in native Sb2Te3/GexSb2Te3+x van der Waals superlattices due to intermixing mitigation

NARCIS (Netherlands)

Cecchi, Stefano; Zallo, Eugenio; Momand, Jamo; Wang, Ruining; Kooi, Bart J.; Verheijen, Marcel A.; Calarco, Raffaella

Superlattices made of Sb2Te3/GeTe phase change materials have demonstrated outstanding performance with respect to GeSbTe alloys in memory applications. Recently, epitaxial Sb2Te3/GeTe superlattices were found to feature GexSb2Te3+x blocks as a result of intermixing between constituting layers.

Improved structural and electrical properties in native Sb2Te3/GexSb2Te3+x van der Waals superlattices due to intermixing mitigation

NARCIS (Netherlands)

Cecchi, S.; Zallo, E.; Momand, J.; Wang, R.; Kooi, B.J.; Verheijen, M.A.; Calarco, R.

Superlattices made of Sb2Te3/GeTe phase change materials have demonstrated outstanding performance with respect to GeSbTe alloys in memory applications. Recently, epitaxial Sb2Te3/GeTe superlattices were found to feature GexSb2Te3+x blocks as a result of intermixing between constituting layers. Here

Investigation of InAs/GaSb-based superlattices by diffraction methods

Energy Technology Data Exchange (ETDEWEB)

Ashuach, Y.; Kauffmann, Y.; Lakin, E. [Department of Materials Engineering, Technion-Israel Institute of Technology, Haifa 32000 (Israel); Zolotoyabko, E., E-mail: zloto@tx.technion.ac.i [Department of Materials Engineering, Technion-Israel Institute of Technology, Haifa 32000 (Israel); Grossman, S.; Klin, O.; Weiss, E. [SCD, SemiConductor Devices, P. O. Box 2250, Haifa 31021 (Israel)

2010-02-15

We use high-resolution X-ray diffraction and high-resolution transmission electron microscopy in order to study the strain state, atomic intermixing and layer thicknesses in the MBE-grown GaSb/InSb/InAs/InSb superlattices. Simple and fast metrology procedure is developed, which allows us to obtain the most important technological parameters, such as the thicknesses of the GaSb, InAs and ultra-thin InSb sub-layers, the superlattice period and the fraction of atomic substitutions in the InSb sub-layers.

Use of calcination in exposing the entrapped Fe particles from multi-walled carbon nanotubes grown by chemical vapour deposition

CSIR Research Space (South Africa)

Kesavan Pillai, Sreejarani

2009-03-01

Full Text Available behaviour of the as-prepared and calcined samples was investigated by thermogravimetric analysis. Calcination in air, at 400°C for 1 h, was found to be an efficient and simple method to extract metallic impurities from the amorphous carbon shells...

First principles simulation of amorphous InSb

Science.gov (United States)

Los, Jan H.; Kühne, Thomas D.; Gabardi, Silvia; Bernasconi, Marco

2013-05-01

Ab initio molecular dynamics simulations based on density functional theory have been performed to generate a model of amorphous InSb by quenching from the melt. The resulting network is mostly tetrahedral with a minor fraction (10%) of atoms in a fivefold coordination. The structural properties are in good agreement with available x-ray diffraction and extended x-ray-absorption fine structure data and confirm the proposed presence of a sizable fraction of homopolar In-In and Sb-Sb bonds whose concentration in our model amounts to about 20% of the total number of bonds.

To study the effect of dopant NiO concentration and duration of calcinations on structural and optical properties of MgO-NiO nanocomposites

Energy Technology Data Exchange (ETDEWEB)

Kumar, Rajesh, E-mail: rkkaushik06@gmail.com [Deptt. of Physics, M.D. University, Rohtak-124001, Haryana (India); Deptt. of Physics,Vaish College of Engineering, Rohtak-124001, Haryana (India); Praveen,; Sharma, Ashwani; Parmar, R.; Dahiya, S. [Deptt. of Physics, M.D. University, Rohtak-124001, Haryana (India); Kishor, N. [Deptt. of Physics, Central University of Haryana (India)

2016-05-06

In present work Magnesium oxide (MgO) samples were doped with different concentration of Transition metal Nickel Oxide(NiO) by using Chemical co-precipitation method. The doping levels were varied from NiO (5%, 10%, 15%) and all the samples were calcined at 600°C for 4hrs and 8hrs respectively. Structural analysis of these calcined materials is carried out by X-ray diffraction (XRD) techniques which reveals that average crystalline sizes are in nano region i.e. 21.77nm-31.13 nm and tabulated in table 1. The powder of calcined samples were also characterized by using various other techniques i.e. Scanning Electron Microscopy (SEM), Fourier Transformation Infrared Spectroscopy (FTIR), UV-Visible spectroscopy, Transmission Electron Microscopy (TEM) etc. The effects of dopant concentration, calcined temperature, calcinations duration on samples were studied and also investigate the effect of varying dopant concentration on morphology and optical properties of calcined nanomaterials. From results it was observed that the crystallite size of nanocomposites increases with increases dopant concentration or increases calcinations duration. The optical band gap decreases with increases sintering time and increase with increases dopant concentrations. TEM results coincide with XRD results and show that particles are polycrystalline in nature. FTIR spectra show that for all samples particles are pure in composition and transmission rate increases with calcinations duration.

Structural transition of (InSb)n clusters at n = 6-10

Science.gov (United States)

Lu, Qi Liang; Luo, Qi Quan; Huang, Shou Guo; Li, Yi De

2016-10-01

An optimization strategy combining global semi-empirical quantum mechanical search with all-electron density functional theory was adopted to determine the lowest energy structure of (InSb)n clusters with n = 6-10. A new structural growth pattern of the clusters was observed. The lowest energy structures of (InSb)6 and (InSb)8 were different from that of previously reported results. Competition existed between core-shell and cage-like structures of (InSb)8. The structural transition of (InSb)n clusters occurred at size n = 8-9. For (InSb)9 and (InSb)10 clusters, core-shell structure were more energetically favorable than the cage. The corresponding electronic properties were investigated.

(Ga,Fe)Sb: A p-type ferromagnetic semiconductor

Energy Technology Data Exchange (ETDEWEB)

Tu, Nguyen Thanh; Anh, Le Duc; Tanaka, Masaaki [Department of Electrical Engineering and Information Systems, The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Hai, Pham Nam [Department of Electrical Engineering and Information Systems, The University of Tokyo, 7-3-1 Hongo, Bunkyo, Tokyo 113-8656 (Japan); Department of Physical Electronics, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro, Tokyo 152-0033 (Japan)

2014-09-29

A p-type ferromagnetic semiconductor (Ga{sub 1−x},Fe{sub x})Sb (x = 3.9%–13.7%) has been grown by low-temperature molecular beam epitaxy (MBE) on GaAs(001) substrates. Reflection high energy electron diffraction patterns during the MBE growth and X-ray diffraction spectra indicate that (Ga,Fe)Sb layers have the zinc-blende crystal structure without any other crystallographic phase of precipitates. Magnetic circular dichroism (MCD) spectroscopy characterizations indicate that (Ga,Fe)Sb has the zinc-blende band structure with spin-splitting induced by s,p-d exchange interactions. The magnetic field dependence of the MCD intensity and anomalous Hall resistance of (Ga,Fe)Sb show clear hysteresis, demonstrating the presence of ferromagnetic order. The Curie temperature (T{sub C}) increases with increasing x and reaches 140 K at x = 13.7%. The crystal structure analyses, magneto-transport, and magneto-optical properties indicate that (Ga,Fe)Sb is an intrinsic ferromagnetic semiconductor.

Effect of Calcination at Synthesis of Mg-Al Hydrotalcite Using co-Precipitation Method

Directory of Open Access Journals (Sweden)

Niar Kurnia Julianti

2017-01-01

Full Text Available The use of hydrotalcite in catalysis has wide attention in academic research and industrial parties. Based on its utilization, hydrotalcite can be active catalyst or support. This research is focused on the investigation of characteristic like spesific surface area of Mg-Al hydrotalcite which is prepared with different temperature of calcination. Synthesis of Mg-Al hydrotalcites with Mg/Al molar ratio 3:1 were prepared by co-precipitation method. Mg(NO33.6H2O and Al(NO33.9H2O as precursors of Mg-Al hydrotalcite. Na2CO3 was used as precipitant agent and NaOH was used as buffer solution. The solution was mixed and aging for 5 hours at 650oC. The dried precipitate was calcined at 2500oC, 3500oC, 4500oC, 5500oC and 6500oC. The characterization of functional group was determined by Fourier Transform Infra Red (FT-IR. The Identical peaks diffractogram were analyzed by X-Ray Diffraction (XRD. The spesific surface area was determined by adsorption-desorption of nitrogen. The largest surface area that obtained from the calcination temperature of 650oC is 156.252 m2/g.

Optical and electrical properties of Te doped AlGaAsSb/AlAsSb Bragg mirrors on InP

OpenAIRE

Toginho Filho, D. O.; Dias, I. F. L.; Duarte, J. L.; Laureto, E.

2006-01-01

We present a comparative study carried out on the optical and electrical characteristics of undoped and Te doped AlGaAsSb/AlAsSb Bragg mirrors with 6.5 pairs of layers and bulk undoped and Te doped AlGaAsSb epilayers alloys lattice matched on InP, grown by molecular beam epitaxy, using SIMS, photoluminescence, reflectivity and IxV techniques. The temperature dependence of PL transitions observed in the Bragg mirrors are similar to that observed in bulk samples and associated with the donor an...

Performance of Cobalt-Based Fischer-Tropsch Synthesis Catalysts Using Dielectric-Barrier Discharge Plasma as an Alternative to Thermal Calcination

International Nuclear Information System (INIS)

Bai Suli; Huang Chengdu; Lv Jing; Li Zhenhua

2012-01-01

Co-based catalysts were prepared by using dielectric-barrier discharge (DBD) plasma as an alternative method to conventional thermal calcination. The characterization results of N 2 -physisorption, temperature programmed reduction (TPR), transmission electron microscope (TEM), and X-ray diffraction (XRD) indicated that the catalysts prepared by DBD plasma had a higher specific surface area, lower reduction temperature, smaller particle size and higher cobalt dispersion as compared to calcined catalysts. The DBD plasma method can prevent the sintering and aggregation of active particles on the support due to the decreased treatment time (0.5 h) at lower temperature compared to the longer thermal calcination at higher temperature (at 500° C for 5 h). As a result, the catalytic performance of the Fischer-Tropsch synthesis on DBD plasma treated Co/SiO 2 catalyst showed an enhanced activity, C 5+ selectivity and catalytic stability as compared to the conventional thermal calcined Co/SiO 2 catalyst.

DWPF simulant CPC studies for SB8

Energy Technology Data Exchange (ETDEWEB)

Koopman, D. C.; Zamecnik, J. R.

2013-06-25

The Savannah River National Laboratory (SRNL) accepted a technical task request (TTR) from Waste Solidification Engineering to perform simulant tests to support the qualification of Sludge Batch 8 (SB8) and to develop the flowsheet for SB8 in the Defense Waste Processing Facility (DWPF). These efforts pertained to the DWPF Chemical Process Cell (CPC). Separate studies were conducted for frit development and glass properties (including REDOX). The SRNL CPC effort had two primary phases divided by the decision to drop Tank 12 from the SB8 constituents. This report focuses on the second phase with SB8 compositions that do not contain the Tank 12 piece. A separate report will document the initial phase of SB8 testing that included Tank 12. The second phase of SB8 studies consisted of two sets of CPC studies. The first study involved CPC testing of an SB8 simulant for Tank 51 to support the CPC demonstration of the washed Tank 51 qualification sample in the SRNL Shielded Cells facility. SB8-Tank 51 was a high iron-low aluminum waste with fairly high mercury and moderate noble metal concentrations. Tank 51 was ultimately washed to about 1.5 M sodium which is the highest wash endpoint since SB3-Tank 51. This study included three simulations of the DWPF Sludge Receipt and Adjustment Tank (SRAT) cycle and Slurry Mix Evaporator (SME) cycle with the sludge-only flowsheet at nominal DWPF processing conditions and three different acid stoichiometries. These runs produced a set of recommendations that were used to guide the successful SRNL qualification SRAT/SME demonstration with actual Tank 51 washed waste. The second study involved five SRAT/SME runs with SB8-Tank 40 simulant. Four of the runs were designed to define the acid requirements for sludge-only processing in DWPF with respect to nitrite destruction and hydrogen generation. The fifth run was an intermediate acid stoichiometry demonstration of the coupled flowsheet for SB8. These runs produced a set of processing

DWPF simulant CPC studies for SB8

International Nuclear Information System (INIS)

Koopman, D. C.; Zamecnik, J. R.

2013-01-01

The Savannah River National Laboratory (SRNL) accepted a technical task request (TTR) from Waste Solidification Engineering to perform simulant tests to support the qualification of Sludge Batch 8 (SB8) and to develop the flowsheet for SB8 in the Defense Waste Processing Facility (DWPF). These efforts pertained to the DWPF Chemical Process Cell (CPC). Separate studies were conducted for frit development and glass properties (including REDOX). The SRNL CPC effort had two primary phases divided by the decision to drop Tank 12 from the SB8 constituents. This report focuses on the second phase with SB8 compositions that do not contain the Tank 12 piece. A separate report will document the initial phase of SB8 testing that included Tank 12. The second phase of SB8 studies consisted of two sets of CPC studies. The first study involved CPC testing of an SB8 simulant for Tank 51 to support the CPC demonstration of the washed Tank 51 qualification sample in the SRNL Shielded Cells facility. SB8-Tank 51 was a high iron-low aluminum waste with fairly high mercury and moderate noble metal concentrations. Tank 51 was ultimately washed to about 1.5 M sodium which is the highest wash endpoint since SB3-Tank 51. This study included three simulations of the DWPF Sludge Receipt and Adjustment Tank (SRAT) cycle and Slurry Mix Evaporator (SME) cycle with the sludge-only flowsheet at nominal DWPF processing conditions and three different acid stoichiometries. These runs produced a set of recommendations that were used to guide the successful SRNL qualification SRAT/SME demonstration with actual Tank 51 washed waste. The second study involved five SRAT/SME runs with SB8-Tank 40 simulant. Four of the runs were designed to define the acid requirements for sludge-only processing in DWPF with respect to nitrite destruction and hydrogen generation. The fifth run was an intermediate acid stoichiometry demonstration of the coupled flowsheet for SB8. These runs produced a set of processing

Positron annihilation studies of high dose Sb implanted silicon

International Nuclear Information System (INIS)

Schut, H.; Eijt, S.W.H.; Beling, C.D.; Ho, K.; Takamura, Y.

2005-01-01

The formation and evolution of vacancies and precipitates created by implantation of 60 keV, 2 x 10 16 cm -2 Sb + in pre-amorphized (0 0 1) Cz-Si is studied using the Doppler broadening (DB) and two-dimensional angular correlation of annihilation radiation (2D-ACAR) positron beam techniques. After implantation, samples were laser annealed (LTA) and subsequently thermal annealed at temperatures ranging from 400 to 1000 deg. C. Implantation-induced vacancy-type defects were detected up to a depth of 280 nm. After LTA, positron annihilation related to both Sb and remaining defects is observed in the first 100 nm below the surface. The deeper region only shows positron trapping at vacancy-type defects with strong reduced concentration. Complete removal is obtained after 600 deg. C anneal. At this temperature, the positron data for the upper region reveals trapping at Sb and Si sites only. With increasing annealing time (at 600 deg. C) or increasing temperature (up to 1000 deg. C) positron annihilation at Sb-sites associated with neighboring vacancies becomes apparent. Results are correlated with the observed Sb electrical deactivation above 600 deg. C, the shift from small Sb aggregates to precipitates and out-diffusion of Sb from the implantation region at higher temperatures

SULFURIC ACID CORROSION OF LOW Sb - Pb BATTERY ALLOYS

African Journals Online (AJOL)

user

1983-09-01

Sep 1, 1983 ... (Manuscript received February,1983). ABSTRACT. The corrosion properties of low Sb - Pb alloys developed for maintenance free motive power industrial batteries was studied by a bare grid constant current method and compared to those of the conventional. Pb- 6% Sb alloy. Low Sb-Pb alloys with Se and ...

Evaluation of calcination temperature and phase composition ratio for new hyroxyapatite

Science.gov (United States)

Salimi, M. N. Ahmad; Chin, H. S.

2017-10-01

The demand of production of hydroxyapatite (HA) has been increasing for the purpose of medical and dental application. HA possesses the excellent properties leads to the priority choice for ceramic bone replacement. Synthesis route by wet chemical precipitation is commonly practised in industrial scale. Calcium hydroxide and Orthophosphoric acid are the precursors for production scale. The synthesis of HA is conducted by varying the synthetic condition: stirring rate, calcium-phosphate and calcination temperature. This paper is focused on the properties of HA produced by regulating the synthetic condition so that the qualities of HA can be well performed. Characterization studies were also carried out by Fourier Transform Infrared Spectroscopy (FT-IR) for functional group identification, Scanning Electron Microscope (SEM) for surface morphology analysis and X-Ray Diffraction (XRD) for phase composition and crystallinity respectively. Narrow particle size distribution contributed to better quality of hydroxyapatite for bone replacement. Both calcium-phosphate ratio and calcination temperature would affect the phase composition of calcium phosphate.

The Enzyme Activity and Substrate Specificity of Two Major Cinnamyl Alcohol Dehydrogenases in Sorghum (Sorghum bicolor), SbCAD2 and SbCAD4.

Science.gov (United States)

Jun, Se-Young; Walker, Alexander M; Kim, Hoon; Ralph, John; Vermerris, Wilfred; Sattler, Scott E; Kang, ChulHee

2017-08-01

Cinnamyl alcohol dehydrogenase (CAD) catalyzes the final step in monolignol biosynthesis, reducing sinapaldehyde, coniferaldehyde, and p -coumaraldehyde to their corresponding alcohols in an NADPH-dependent manner. Because of its terminal location in monolignol biosynthesis, the variation in substrate specificity and activity of CAD can result in significant changes in overall composition and amount of lignin. Our in-depth characterization of two major CAD isoforms, SbCAD2 (Brown midrib 6 [bmr6]) and SbCAD4, in lignifying tissues of sorghum ( Sorghum bicolor ), a strategic plant for generating renewable chemicals and fuels, indicates their similarity in both structure and activity to Arabidopsis ( Arabidopsis thaliana ) CAD5 and Populus tremuloides sinapyl alcohol dehydrogenase, respectively. This first crystal structure of a monocot CAD combined with enzyme kinetic data and a catalytic model supported by site-directed mutagenesis allows full comparison with dicot CADs and elucidates the potential signature sequence for their substrate specificity and activity. The L119W/G301F-SbCAD4 double mutant displayed its substrate preference in the order coniferaldehyde > p -coumaraldehyde > sinapaldehyde, with higher catalytic efficiency than that of both wild-type SbCAD4 and SbCAD2. As SbCAD4 is the only major CAD isoform in bmr6 mutants, replacing SbCAD4 with L119W/G301F-SbCAD4 in bmr6 plants could produce a phenotype that is more amenable to biomass processing. © 2017 American Society of Plant Biologists. All Rights Reserved.

Study for material analogs of FeSb2: Material design for thermoelectric materials

Science.gov (United States)

Kang, Chang-Jong; Kotliar, Gabriel

2018-03-01

Using the ab initio evolutionary algorithm (implemented in uspex) and electronic structure calculations we investigate the properties of a new thermoelectric material FeSbAs, which is a material analog of the enigmatic thermoelectric FeSb2. We utilize the density functional theory and the Gutzwiller method to check the energetics. We find that FeSbAs can be made thermodynamically stable above ˜30 GPa. We investigate the electronic structure and thermoelectric properties of FeSbAs based on the density functional theory and compare with those of FeSb2. Above 50 K, FeSbAs has higher Seebeck coefficients than FeSb2. Upon doping, the figure of merit becomes larger for FeSbAs than for FeSb2. Another material analog FeSbP, was also investigated, and found thermodynamically unstable even at very high pressure. Regarding FeSb2 as a member of a family of compounds (FeSb2, FeSbAs, and FeSbP) we elucidate what are the chemical handles that control the gaps in this series. We also investigate solubility (As or P for Sb in FeSb2) we found As to be more soluble. Finally, we study a two-band model for thermoelectric properties and find that the temperature dependent chemical potential and the presence of the ionized impurities are important to explain the extremum in the Seebeck coefficient exhibited in experiments for FeSb2.

Thermoelectric properties and microstructure of Mg3Sb2

International Nuclear Information System (INIS)

Condron, Cathie L.; Kauzlarich, Susan M.; Gascoin, Franck; Snyder, G. Jeffrey

2006-01-01

Mg 3 Sb 2 has been prepared by direct reaction of the elements. Powder X-ray diffraction, thermal gravimetric, differential scanning calorimetery, and microprobe data were obtained on hot pressed samples. Single phase samples of Mg 3 Sb 2 were prepared and found to contain oxygen at the grain boundaries and to lose Mg and oxidize at temperatures above 900 K. Thermoelectric properties were characterized by Seebeck, electrical resistivity, and thermal conductivity measurements from 300 to 1023 K, and the maximum zT was found to be 0.21 at ∼875 K. - Graphical abstract: Dimensionless figure of merit for Mg 3 Sb 2 hot pressed and sintered at 873 K. The inset illustrates the crystal structure of Mg 3 Sb 2 along the [100] direction (white=Mg, black=Sb)

4.2. The kinetics of nitric acid decomposition of calcined borosilicate raw material of Ak-Arkhar Deposit

International Nuclear Information System (INIS)

Mirsaidov, U.M.; Kurbonov, A.S.; Mamatov, E.D.

2015-01-01

Present article is devoted to kinetics of nitric acid decomposition of calcined borosilicate raw material of Ak-Arkhar Deposit. The dependence of nitric acid decomposition of calcined boric raw material for extraction of boron oxide on temperature (20-100 deg C) and process duration (15-60 minutes) was defined. It was defined that at temperature increasing the extraction rate of boron oxide increases from 20.8 to 78.6%.

Thermoelectric properties of ZnSb films grown by MOCVD

International Nuclear Information System (INIS)

Venkatasubramanian, R.; Watko, E.; Colpitts, T.

1997-04-01

The thermoelectric properties of metallorganic chemical vapor deposited (MOCVD) ZnSb films are reported. The growth conditions necessary to obtain stoichiometric ZnSb films and the effects of various growth parameters on the electrical conductivity and Seebeck coefficients of the films are described. The as-grown ZnSb films are p-type. It was observed that the growth of thicker ZnSb films lead to improved carrier mobilities and lower free-carrier concentrations. The Seebeck coefficient of ZnSb films was found to rise rapidly at approximately 160 to 170 C, with peak Seebeck coefficients as high as 470 microV/K at 220 C. The various growth conditions, including the use of intentional dopants, to improve the Seebeck coefficients at room temperature and above, are discussed. A short annealing of the ZnSb films at temperatures of ∼ 200 C resulted in reduced free-carrier levels and higher Seebeck coefficients at 300 K. Finally, ZT values based on preliminary thermal conductivity measurements using the 3-ω method are reported

The electronic band structures of InNxAs1-x, InNxSb1-x and InAsxSb1-x alloys

International Nuclear Information System (INIS)

Mohammad, Rezek; Katircioglu, Senay

2009-01-01

The band gap bowings of InN x As 1-x , InN x Sb 1-x , and InAs x Sb 1-x alloys defined by the optimized lattice constants are investigated using empirical tight binding (ETB) method. The present ETB energy parameters which take the nearest neighbor interactions into account with sp 3 d 2 basis are determined to be sufficient to provide a typical feature for the band gap bowings of the alloys. The band gap bowing parameter is found to be relatively large in both InN x As 1-x and InN x Sb 1-x compared to InAs x Sb 1-x alloys. Moreover, the variation of the fundamental band gaps of InN x Sb 1-x alloys is sharper than that of InN x As 1-x alloys for small concentrations of N. Besides, a small amount of nitrogen is determined to be more effective in InN x Sb 1-x than in InN x As 1-x alloys to decrease the corresponding effective masses of the electrons around Γ points

Crystal structure and bonding characteristics of In-doped β-Zn4Sb3

International Nuclear Information System (INIS)

Tang, Dingguo; Zhao, Wenyu; Cheng, Sudan; Wei, Ping; Yu, Jian; Zhang, Qingjie

2012-01-01

The effects of indium impurity on the crystal structure and bonding characteristics of In-doped β-Zn 4 Sb 3 were investigated by powder X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS). The XRD Rietveld refinement indicates that the indium impurity preferentially substitutes one of Sb atoms in Sb–Sb dimer at the 12c Sb(2) site and simultaneously leads to the increase of Zn occupancy. The observations of binding energy shift and a new valence state in Sb 3d core-level XPS spectra can be attributed to the charge transfer from In and Zn to Sb. As a result, more electropositive Zn atoms are needed to maintain the charge balance. The reduction of the lattice thermal conductivity is ascribed to the formation of the asymmetric Sb–In bond, resulting in much low lattice thermal conductivity of 0.49 W −1 K −1 of Zn 4 Sb 2.96 In 0.04 . - Graphical abstract: The indium impurity substitutes one of Sb atoms in Sb–Sb dimer, resulting the charge transfer from In to Sb, which leads to the binding energy of Sb 3d core level XPS spectra shift to low value. Highlights: ► The indium impurity preferentially substitutes one of Sb atoms in Sb–Sb dimer at the 12c Sb(2) site. ► The occupancy of Zn increases by the In substitution for Sb, whereas that of Sb keeps constant. ► The binding energy of Sb 3d shifts to low value. ► The charge transfer occurs from In and Zn to Sb.

Synthesis and cathodoluminescence of Sb/P co-doped GaN nanowires

International Nuclear Information System (INIS)

Wang, Zaien; Liu, Baodan; Yuan, Fang; Hu, Tao; Zhang, Guifeng; Dierre, Benjamin; Hirosaki, Naoto; Sekiguchi, Takashi; Jiang, Xin

2014-01-01

Sb/P co-doped Gallium Nitride (GaN) nanowires were synthesized via a simple chemical vapor deposition (CVD) process by heating Ga 2 O 3 and Sb powders in NH 3 atmosphere. Scanning electron microscope (SEM), X-ray diffraction (XRD), transmission electron microscope (TEM) and energy dispersive X-ray spectroscopy (EDS) measurements confirmed the as-synthesized products were Sb/P co-doped GaN nanowires with rough morphology and hexagonal wurtzite structure. Room temperature cathodoluminescence (CL) demonstrated that an obvious band shift of GaN nanowires can be observed due to Sb/P co-doping. Possible explanation for the growth and luminescence mechanism of Sb/P co-doped GaN nanowires was discussed. Highlight: • Sb/P co-doped GaN nanowires were synthesized through a well-designed multi-channel chemical vapor deposition (CVD) process. • Sb/P co-doping leads to the crystallinity deterioration of GaN nanowires. • Sb/P co-doping caused the red-shift of GaN nanowires band-gap in UV range. • Compared with Sb doping, P atoms are more easy to incorporate into the GaN lattice

The Quantum Chemistry Calculation and Thermoelectrics of Bi-Sb-Te Series

Institute of Scientific and Technical Information of China (English)

无

2002-01-01

The density function theory and discrete variation method(DFT-DVM) was used to study correlation between composition, structure, chemical bond,and property of thermoelectrics of Bi-Sb-Te series.8 models of Bi20-xSbxTe32(x=0,2,6,8,12,14,18 and 20) were calculated.The results show that there is less difference in the ionic bonds between Te(Ⅰ)-Bi(Sb) and Te(Ⅱ)-Bi(Sb), but the covalent bond of Te(Ⅰ)-Bi(Sb) is stronger than that of Te(Ⅱ)-Bi(Sb).The interaction between Te(Ⅰ) and Te(Ⅰ) in different layers is the weakest and the interaction should be Van Der Waals power.The charge of Sb is lower than that of Bi,and the ionic bond of Te-Sb is weaker than that of Te-Bi.The covalent bond of Te-Sb is also weaker than that of Te-Bi.Therefore,the thermoelectric property may be improved by adjusting the electrical conductivity and thermal conductivity through changing the composition in the compounds of Bi-Sb-Te. The calculated results are consistent with the experiments.

Synthesis and crystal structure of Cd2SbBr2

International Nuclear Information System (INIS)

Reshetova, L.N.; Shevel'kov, A.V.; Popovkin, B.A.

1999-01-01

A new cadmium antimonidobromide, i.e. Cd 2 SbBr 2 , has been synthesized by the standard ampoule method. The compound is crystallized in monoclinic system of sp. gr. P2 1 :a=8.244 (1), b=9.920(1), c=8.492(1) A, Β=116.80(1) deg. Binuclear anions of Sb 2 4- (Sb-Sb 2.78 A), octahedrically surrounded by six cadmium atoms, are a basic specific feature of the structure. Octahedrons of Sb 2 Cd 6 , by collectivizing the equatorial vertices. form layers, the alternation mode of which is similar to the one described for cadmium and mercury arsenidochlorides

Neutron scattering study of Ce3Au3Sb4

International Nuclear Information System (INIS)

Kasaya, Mitsuo; Katoh, Kenichi; Kohgi, Masahumi; Osakabe, Toyotaka

1993-01-01

Rare-earth compounds with an Y 3 Au 3 Sb 4 -type crystal structure are semiconductors or semi-metals. Among them, Ce 3 Au 3 Sb 4 is a semiconductor with an activation energy of about 640 K and shows no magnetic order down to 1.5 K. The magnetic part of the specific heat for Ce 3 Au 3 Sb 4 obtained by subtracting the value for La 3 Au 3 Sb 4 from the total specific heat of Ce 3 Au 3 Sb 4 shows a broad peak at around 10 K, the origin of which is well explained by the crystalline-field splitting determined by neutron scattering. (author)

Electroluminescence in p-InAs/AlSb/InAsSb/AlSb/p(n)-GaSb type II heterostructures with deep quantum wells at the interface

Czech Academy of Sciences Publication Activity Database

Mikhailova, M. P.; Ivanov, E.V.; Moiseev, K. D.; Yakovlev, Yu. P.; Hulicius, Eduard; Hospodková, Alice; Pangrác, Jiří; Šimeček, Tomislav

2010-01-01

Roč. 44, č. 1 (2010), 66-71 ISSN 1063-7826 Institutional research plan: CEZ:AV0Z10100521 Keywords : electroluninescence * MOVPE * GaSb * InAs * quantum well Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 0.603, year: 2010

Atmospheric pressure plasma assisted calcination by the preparation of TiO2 fibers in submicron scale

Science.gov (United States)

Medvecká, Veronika; Kováčik, Dušan; Zahoranová, Anna; Černák, Mirko

2018-01-01

Atmospheric pressure plasma assisted calcination by the preparation of TiO2 submicron fibers as a low-temperature alternative to the conventional thermal annealing was studied. A special type of dielectric barrier discharge was used for plasma treatment of hybrid titanium butoxide/polyvinylpyrrolidone (Ti(Bu)/PVP) fibers prepared by forcespinning to decompose and oxidize the base polymer and precursor. The obtained fibers were characterized by changes in chemical bonds on the surface using Fourier Transform Infrared Spectroscopy (FTIR), chemical composition by using Energy-Dispersive X-Ray Spectroscopy (EDX), X-ray Photoelectron Spectroscopy (XPS). The morphology of fibers was investigated by Scanning Electron Microscopy (SEM). A significant decrease of organic components was reached by short plasma exposure times less than 1 h. The obtained fibers exhibit a high surface porosity without degradation of the fibrous structure. The results obtained indicate that atmospheric pressure plasma assisted calcination can be a viable low-temperature, energy- and time-saving alternative or pre-treatment method for the conventional high-temperature thermal calcination.

Sb interactions with TaC precipitates and Cu in ion-implanted α-Fe

International Nuclear Information System (INIS)

Follstaedt, D.M.; Myers, S.M.

1980-01-01

The interactions of Sb with the other species implanted into Fe to form Fe-Ta-C-Sb and Fe-Cu-Sb alloys have been examined with transmission electron microscopy and Rutherford backscattering following annealing at 873 0 K. Trapping of Sb at TaC precipitates is observed in the former alloy just as was previously observed in Fe-Ti-C-Sb. In Fe-Cu-Sb, Sb interactions are governed by the atomic ratio of Sb to Cu. For ratios between 0.2 to 0.4, the compound β-Cu 3 Sb was observed to form. For Sb to Cu ratios approx.< 0.1, fcc Cu precipitates were observed. In addition to the expected Sb dissolution in Cu, Sb trapping by Cu precipitates is also observed. The binding enthalpy of Sb at both TaC and Cu precipitates with respect to a solution site in the bcc Fe is the same as observed for TiC, approx. 0.4 eV. The constancy of the binding enthalpy at such chemically dissimilar precipitates supports the hypothesis that the trapping is due to the structural discontinuity of the precipitate-host interface. The observed Sb trapping at precipitates is of potential significance for the control of temper embrittlement in bcc steels

The formation mechanisms and optical characteristics of GaSb quantum rings

International Nuclear Information System (INIS)

Lin, Wei-Hsun; Pao, Chun-Wei; Wang, Kai-Wei; Liao, Yu-An; Lin, Shih-Yen

2013-01-01

The growth mechanisms and optical characteristics of GaSb quantum rings (QRs) are investigated. Although As-for-Sb exchange is the mechanism responsible for the dot-to-ring transition, significant height difference between GaSb quantum dots (QDs) and QRs in a dot/ring mixture sample suggests that the dot-to-ring transition is not a spontaneous procedure. Instead, it is a rapid transition procedure as long as it initiates. A model is established to explain this phenomenon. Larger ring inner diameters and heights of the sample with longer post Sb soaking time suggest that As-for-Sb exchange takes places in both vertical and lateral directions. The decreasing ring densities, enlarged ring inner/outer diameters and eventually flat GaSb surfaces observed with increasing growth temperatures are resulted from enhanced adatom migration and As-for-Sb exchange with increasing growth temperatures

Increasing the thermoelectric power factor of Ge17Sb2Te20 by adjusting the Ge/Sb ratio

Science.gov (United States)

Williams, Jared B.; Mather, Spencer P.; Page, Alexander; Uher, Ctirad; Morelli, Donald T.

2017-07-01

We have investigated the thermoelectric properties of Ge17Sb2Te20. This compound is a known phase change material with electronic properties that depend strongly on temperature. The thermoelectric properties of this compound can be tuned by altering the stoichiometry of Ge and Sb without the use of additional foreign elements during synthesis. This tuning results in a 26% increase in the thermoelectric power factor at 723 K. Based on a single parabolic band model we show that the pristine material is optimally doped, and thus, a reduction in the lattice thermal conductivity of pure Ge17Sb2Te20 should result in an enhanced thermoelectric figure of merit.

InAs/GaSb/AlSb composite quantum well structure preparation with help of reflectance anisotropy spectroscopy

Czech Academy of Sciences Publication Activity Database

Hospodková, Alice; Hulicius, Eduard; Pangrác, Jiří; Dominec, Filip; Mikhailova, M. P.; Veinger, A.I.; Kochman, I.V.

2017-01-01

Roč. 464, Apr (2017), s. 206-210 ISSN 0022-0248 R&D Projects: GA MŠk LM2015087; GA MŠk LO1603 Institutional support: RVO:68378271 Keywords : low dimensional structures * MOVPE * InAs/GaSb composite quantum wells * AlSb Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 1.751, year: 2016

First-principles study of amorphous Ga4Sb6Te3 phase-change alloys

Science.gov (United States)

Bouzid, Assil; Gabardi, Silvia; Massobrio, Carlo; Boero, Mauro; Bernasconi, Marco

2015-05-01

First-principles molecular dynamics simulations within the density functional theory framework were performed to generate amorphous models of the Ga4Sb6Te3 phase change alloy by quenching from the melt. We find that Ga-Sb and Ga-Te are the most abundant bonds with only a minor amount of Sb-Te bonds participating to the alloy network. Ga and four-coordinated Sb atoms present a tetrahedral-like geometry, whereas three-coordinated Sb atoms are in a pyramidal configuration. The tetrahedral-like geometries are similar to those of the crystalline phase of the two binary compounds GaTe and GaSb. A sizable fraction of Sb-Sb bonds is also present, indicating a partial nanoscale segregation of Sb. Despite the fact that the composition Ga4Sb6Te3 lies on the pseudobinary Ga Sb -Sb2Te3 tie line, the amorphous network can be seen as a mixture of the two binary compounds GaTe and GaSb with intertwined elemental Sb.

Superlattice-like SnSb{sub 4}/Ga{sub 3}Sb{sub 7} thin films for ultrafast switching phase-change memory application

Energy Technology Data Exchange (ETDEWEB)

Hu, Yifeng [Tongji University, Key Laboratory of Advanced Civil Engineering Materials of Ministry of Education, Functional Materials Research Laboratory, School of Materials Science and Engineering, Shanghai (China); Jiangsu University of Technology, School of Mathematics and Physics, Changzhou (China); He, Zifang; Zhai, Jiwei [Tongji University, Key Laboratory of Advanced Civil Engineering Materials of Ministry of Education, Functional Materials Research Laboratory, School of Materials Science and Engineering, Shanghai (China); Wu, Pengzhi; Lai, Tianshu [Sun Yat-Sen University, State Key Laboratory of Optoelectronic Materials and Technology, Department of Physics, Guangzhou (China); Song, Sannian; Song, Zhitang [Chinese Academy of Sciences, State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Micro-system and Information Technology, Shanghai (China)

2015-11-15

The carrier concentration of Sb-rich phase SnSb{sub 4}, Ga{sub 3}Sb{sub 7} and superlattice-like [SnSb{sub 4}(3.5 nm)/Ga{sub 3}Sb{sub 7}(4 nm)]{sub 7} (SLL-7) thin films as a function of annealing temperature was investigated to explain the reason of resistance change. The activation energy for crystallization was calculated with a Kissinger equation to estimate the thermal stability. In order to illuminate the transition mechanisms, the crystallization kinetics of SLL-7 were explored by using Johnson-Mehl-Avrami theory. The obtained values of Avrami indexes indicate that a one-dimensional growth-dominated mechanism is responsible for the set transition of SLL-7 thin film. X-ray diffractometer and Raman scattering spectra were recorded to investigate the change of crystalline structure. The measurement of atomic force microscopy indicated that SLL-7 thin film has a good smooth surface. A picosecond laser pump-probe system was used to test and verify phase-change speed of the SLL-7 thin film. (orig.)

SYNROC production using a fluid bed calciner

International Nuclear Information System (INIS)

Ackerman, F.J.; Grens, J.Z.; Ryerson, F.J.; Hoenig, C.L.; Bazan, F.; Campbell, J.H.

1982-01-01

SYNROC is a titanate-based ceramic developed for immobilization of high-level nuclear reactor wastes in solid form. Fluid-bed SYNROC production permits slurry drying, calcining and redox to be carried out in a single unit. We present results of studies from two fluid beds; the Idaho Exxon internally-heated unit and the externally-heated unit constructed at Lawrence Livermore National laboratory. Bed operation over a range of temperature, feed rate, fluidizing rate and redox conditions indicate that high density, uniform particle-size SYNROC powders are produced which facilitate the densification step and give HUP parts with dense, well-developed phases and good leaching characteristics. 3 figures, 3 tables

Sb(III) and Sb(V) separation and analytical speciation by a continuous tandem on-line separation device in connection with inductively coupled plasma atomic emission spectrometry

Energy Technology Data Exchange (ETDEWEB)

Menendez Garcia, A. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.; Perez Rodriguez, M.C. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.; Sanchez Uria, J.F. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.; Sanz-Medel, A. [Oviedo Univ. (Spain). Dept. of Phys. and Anal. Chem.

1995-09-01

A sensitive, precise and automated non-chromatographic method for Sb(III) and Sb(V) analytical speciation based on a continuous tandem on-line separation device in connection with inductively coupled plasma-atomic emission (ICP-AES) detection is proposed. Two on-line successive separation steps are included into this method: a continuous liquid-liquid extraction of Sb(III) with ammonium pyrrolidine dithiocarbamate (APDC) into methylisobuthylketone (MIBK), followed by direct stibine generation from the organic phase. Both separation steps are carried out in a continuous mode and on-line with the ICP-AES detector. Optimization of experimental conditions for the tandem separation and ICP-AES detection are investigated in detail. Detection limits for Sb(III) were 3 ng.mL{sup -1} and for Sb(V) 8 ng.mL{sup -1}. Precisions observed are in the range {+-} 5%. The proposed methodology has been applied to Sb(III) and Sb(V) speciation in sea-water samples. (orig.)

Trace Elements and Minerals in Fumarolic Sulfur: The Case of Ebeko Volcano, Kuriles

Directory of Open Access Journals (Sweden)

E. P. Shevko

2018-01-01

Full Text Available Native sulfur deposits on fumarolic fields at Ebeko volcano (Northern Kuriles, Russia are enriched in chalcophile elements (As-Sb-Se-Te-Hg-Cu and contain rare heavy metal sulfides (Ag2S, HgS, and CuS, native metal alloys (Au2Pd, and some other low-solubility minerals (CaWO4, BaSO4. Sulfur incrustations are impregnated with numerous particles of fresh and altered andesite groundmass and phenocrysts (pyroxene, magnetite as well as secondary minerals, such as opal, alunite, and abundant octahedral pyrite crystals. The comparison of elemental abundances in sulfur and unaltered rocks (andesite demonstrated that rock-forming elements (Ca, K, Fe, Mn, and Ti and other lithophile and chalcophile elements are mainly transported by fumarolic gas as aerosol particles, whereas semimetals (As, Sb, Se, and Te, halogens (Br and I, and Hg are likely transported as volatile species, even at temperatures slightly above 100°C. The presence of rare sulfides (Ag2S, CuS, and HgS together with abundant FeS2 in low-temperature fumarolic environments can be explained by the hydrochloric leaching of rock particles followed by the precipitation of low-solubility sulfides induced by the reaction of acid solutions with H2S at ambient temperatures. The elemental composition of native sulfur can be used to qualitatively estimate elemental abundances in low-temperature fumarolic gases.

Point defect balance in epitaxial GaSb

International Nuclear Information System (INIS)

Segercrantz, N.; Slotte, J.; Makkonen, I.; Kujala, J.; Tuomisto, F.; Song, Y.; Wang, S.

2014-01-01

Positron annihilation spectroscopy in both conventional and coincidence Doppler broadening mode is used for studying the effect of growth conditions on the point defect balance in GaSb:Bi epitaxial layers grown by molecular beam epitaxy. Positron annihilation characteristics in GaSb are also calculated using density functional theory and compared to experimental results. We conclude that while the main positron trapping defect in bulk samples is the Ga antisite, the Ga vacancy is the most prominent trap in the samples grown by molecular beam epitaxy. The results suggest that the p–type conductivity is caused by different defects in GaSb grown with different methods.

Adsorption of basic chromium sulfate used in the tannery industries by calcined hydrotalcite

International Nuclear Information System (INIS)

Lopez M, B. E.; Rivera R, R.; Iturbe G, J. L.; Olguin G, M. T.

2011-01-01

The sorption behavior of the chemical species of Cr(III) from aqueous solutions by hydrotalcite calcined products was investigated considering the equilibrium ph (5.0 to 8.9) and the chromium concentration in aqueous solution (from 10.6 to 430.0 mmol/L) to obtain the corresponding isotherms. Each solution was prepared from basic Cr(III) sulphate which is a primary tanning agent used in the tannery industries. In this work no previous oxidation treatment was done to form Cr(vi) in order to remove the chromium from aqueous solutions by hydrotalcite. The amount of chromium in the remaining solutions after the sorption processes in a batch system by visible spectroscopy (Vis) was determined. The calcined hydrotalcite before and after the contact with the chromium(III) solutions by X-ray power diffraction, thermogravimetric analysis and Fourier transformed infrared spectroscopy, were characterized. The specific are by Brunauer, Emmett and Teller (Bet) method of each sample was also evaluated. It was found that under the experimental conditions of this work hydrolyzed species of Cr(III) are precipitated on the surface of the calcined hydrotalcite instead other adsorption mechanism, and the sulfate ions were the responsible to regenerated the crystalline structure of hydrotalcite, therefore the results are discussed in terms of both Cr(III) and sulfate chemical species. (Author)

Adsorption of basic chromium sulfate used in the tannery industries by calcined hydrotalcite

Energy Technology Data Exchange (ETDEWEB)

Lopez M, B. E.; Rivera R, R.; Iturbe G, J. L.; Olguin G, M. T., E-mail: beatriz.lopez@inin.gob.mx [ININ, Departamento de Quimica, Carretera Mexico-Toluca s/n, 52750 Ocoyoacac, Estado de Mexico (Mexico)

2011-07-01

The sorption behavior of the chemical species of Cr(III) from aqueous solutions by hydrotalcite calcined products was investigated considering the equilibrium ph (5.0 to 8.9) and the chromium concentration in aqueous solution (from 10.6 to 430.0 mmol/L) to obtain the corresponding isotherms. Each solution was prepared from basic Cr(III) sulphate which is a primary tanning agent used in the tannery industries. In this work no previous oxidation treatment was done to form Cr(vi) in order to remove the chromium from aqueous solutions by hydrotalcite. The amount of chromium in the remaining solutions after the sorption processes in a batch system by visible spectroscopy (Vis) was determined. The calcined hydrotalcite before and after the contact with the chromium(III) solutions by X-ray power diffraction, thermogravimetric analysis and Fourier transformed infrared spectroscopy, were characterized. The specific are by Brunauer, Emmett and Teller (Bet) method of each sample was also evaluated. It was found that under the experimental conditions of this work hydrolyzed species of Cr(III) are precipitated on the surface of the calcined hydrotalcite instead other adsorption mechanism, and the sulfate ions were the responsible to regenerated the crystalline structure of hydrotalcite, therefore the results are discussed in terms of both Cr(III) and sulfate chemical species. (Author)

Three dimensional atom probe imaging of GaAsSb quantum rings

International Nuclear Information System (INIS)

Beltran, A.M.; Marquis, E.A.; Taboada, A.G.; Ripalda, J.M.; Garcia, J.M.; Molina, S.I.

2011-01-01

Unambiguous evidence of ring-shaped self-assembled GaSb nanostructures grown by molecular beam epitaxy is presented on the basis of atom-probe tomography reconstructions and dark field transmission electron microscopy imaging. The GaAs capping process causes a strong segregation of Sb out of the center of GaSb quantum dots, leading to the self-assembled GaAs x Sb 1-x quantum rings of 20-30 nm in diameter with x∼0.33. -- Highlights: → Atom-probe tomography resolves QR morphology of GaSb self-assembled GaSb buried nanostructures. → From atom-probe tomography compositional distribution has been obtained. → Strong segregation and morphological changes are observed with respect to uncapped QR.

Alternative synthetic route for the heterometallic CO-releasing [Sb@Rh12(CO27]3− icosahedral carbonyl cluster and synthesis of its new unsaturated [Sb@Rh12(CO24]4− and dimeric [{Sb@Rh12Sb(CO25}2Rh(CO2PPh3]7− derivatives

Directory of Open Access Journals (Sweden)

Cristina Femoni

2016-10-01

Full Text Available The hetero-metallic [Sb@Rh12(CO27]3− cluster has been known as for over three decades thanks to Vidal and co-workers, and represents the first example of an E-centered (E=heteroatom icosahedral rhodium carbonyl cluster. However, its synthesis required high temperature (140–160 °C and elevated CO pressure (400 atm. Applying the redox condensation method for cluster preparation, we herein report a new synthetic, high-yield route for preparing [Sb@Rh12(CO27]3− under much milder conditions of temperature and pressure. Notably, when the same synthesis was carried out under N2 instead of CO atmosphere, the new isostructural but unsaturated derivative [Sb@Rh12(CO24]4− was obtained, for which we report the full X-ray structural characterization. This species represents one of the few examples of an icosahedral cluster disobeying the electron-counting Wade-Mingos rules, possessing less than the expected 170 cluster valence electrons (CVEs. Judging from IR monitoring, the two species can be obtained one from the other by switching between N2 and CO atmosphere, making [Sb@Rh12(CO27]3− a spontaneous CO-releasing molecule. Finally, the study of the chemical reactivity of [Sb@Rh12(CO27]3− with PPh3 allowed us to obtain the new [{Sb@Rh12Sb(CO25}2Rh(CO2PPh3]7− dimeric compound, for which we herein report the full X-ray structural and 31P NMR analyses.

Phase transitions in thin films of Sn-Sb-Se system

International Nuclear Information System (INIS)

Samsudi Sakrani; Abdalla Belal Adam; Yussof Wahab

1998-01-01

The preparation and formation of covalent ternary Sn-Sb-Se system were investigated. A solid state reaction technique was employed whereby the evaporated multilayers of Sn/Se/Sb/Sn reacted chemically at a fixed temperature of 240 o C and were allowed to a room temperature slow-cooling. X-ray diffraction analysis showed that phase changes occurred in the system, with indication of amorphization for the predicted Sn 9 .3Sb 8 .1Se 4 4.9 and Sn 1 3.2Sb 4 3.4Se 4 3.4 compositions. These enabled the preliminary topological phase transitions of Sn-Sb-Se system according to the Gibb's triangle in which the areas of crystalline-amorphous were located. (Author)

Synthesis of zirconium dioxide by ultrasound assisted precipitation: effect of calcination temperature.

Science.gov (United States)

Prasad, Krishnamurthy; Pinjari, D V; Pandit, A B; Mhaske, S T

2011-09-01

Nanostructured zirconium dioxide was synthesized from zirconyl nitrate using both conventional and ultrasound assisted precipitation in alkaline medium. The synthesized samples were calcinated at temperatures ranging from 400°C to 900°C in steps of 100°C. The ZrO(2) specimens were characterized using X-ray Diffraction (XRD) and Scanning Electron Microscopy (SEM). The thermal characteristics of the samples were studied via Differential Scanning Calorimetry-Thermo-Gravimetry Analysis (DSC-TGA). The influence of the calcination temperature on the phase transformation process from monoclinic to tetragonal to cubic zirconia and its consequent effect on the crystallite size and % crystallinity of the synthesized ZrO(2) was studied and interpreted. It was observed that the ultrasound assisted technique helped to hasten to the phase transformation and also at some point resulted in phase stabilization of the synthesized zirconia. Copyright © 2011 Elsevier B.V. All rights reserved.

Effect of lanthanide contraction on the mixed polyamine systems Ln/Sb/Se/(en+dien) and Ln/Sb/Se/(en+trien): Syntheses and characterizations of lanthanide complexes with a tetraelenidoantimonate ligand

International Nuclear Information System (INIS)

Zhao Jing; Liang Jingjing; Pan Yingli; Zhang Yong; Jia Dingxian

2011-01-01

Mixed polyamine systems Ln/Sb/Se/(en+dien) and Ln/Sb/Se/(en+trien) (Ln=lanthanide, en=ethylenediamine, dien=diethylenetriamine, trien=triethylenetetramine) were investigated under solvothermal conditions, and novel mixed-coordinated lanthanide(III) complexes [Ln(en) 2 (dien)(η 2 -SbSe 4 )] (Ln=Ce(1a), Nd(1b)), [Ln(en) 2 (dien)(SbSe 4 )] (Ln=Sm(2a), Gd(2b), Dy(2c)), [Ln(en)(trien)(μ-η 1 ,η 2 -SbSe 4 )] ∞ (Ln=Ce(3a), Nd(3b)) and [Sm(en)(trien)(η 2 -SbSe 4 )] (4a) were prepared. Two structural types of lanthanide selenidoantimonates were obtained across the lanthanide series in both en+dien and en+trien systems. The tetrahedral anion [SbSe 4 ] 3- acts as a monodentate ligand mono-SbSe 4 , a bidentate chelating ligand η 2 -SbSe 4 or a tridentate bridging ligand μ-η 1 ,η 2 -SbSe 4 to the lanthanide(III) center depending on the Ln 3+ ions and the mixed ethylene polyamines, indicating the effect of lanthanide contraction on the structures of the lanthanide(III) selenidoantimonates. The lanthanide selenidoantimonates exhibit semiconducting properties with E g between 2.08 and 2.51 eV. - Graphical Abstract: Two structural types of lanthanide(III) selenidoantimonates are formed in both en-dien and en-trien mixed polyamines across lanthanide series, indicating the lanthanide contraction effect on the structures of the lanthanide(III) selenidoantimonates. Highlights: → Two structural types of lanthanide selenidoantimonates are prepared across the lanthanide series in both Ln/Sb/Se/(en+dien) and Ln/Sb/Se/(en+trien) systems. → The [SbSe 4 ] 3- anion acts as a mono-SbSe 4 , a η 2 -SbSe 4 or a μ-η 1 ,η 2 -SbSe 4 ligand to the Ln 3+ ions. → The soft base ligand [SbSe 4 ] 3- can be controlled to coordinate to the Ln 3+ ions with en+dien and en+trien as co-ligands.

Residual carrier density in GaSb grown on Si substrates

International Nuclear Information System (INIS)

Akahane, Kouichi; Yamamoto, Naokatsu; Gozu, Shin-ichiro; Ueta, Akio; Ohtani, Naoki

2006-01-01

The relationships between the densities of residual carriers and those of dislocation in GaSb films grown on Si substrates were investigated. Dislocation density was evaluated by cross-sectional transmission electron microscopy (TEM). The TEM images indicated that the dislocation density after a 5-μm-thick GaSb film was grown was below 1 x 10 8 /cm 2 although the density near the interface between the Si substrate and the GaSb film was about 3 x 10 9 /cm 2 . Forming a dislocation loop by growing a thick GaSb layer may decrease the dislocation density. The density and mobility of the residual carrier were investigated by Hall measurement using the van der Pauw method. The residual carriers in GaSb grown on Si substrates were holes, and their densities decreased significantly from 4.2 x 10 18 to 1.4 x 10 17 /cm 3 as GaSb thickness was increased from 500 to 5500 nm

Oxyfuel carbonation/calcination cycle for low cost CO2 capture in existing power plants

International Nuclear Information System (INIS)

Romeo, Luis M.; Abanades, J. Carlos; Escosa, Jesus M.; Pano, Jara; Gimenez, Antonio; Sanchez-Biezma, Andres; Ballesteros, Juan C.

2008-01-01

Postcombustion CO 2 capture is the best suitable capture technology for existing coal power plants. This paper focuses on an emerging technology that involves the separation of CO 2 using the reversible carbonation reaction of CaO to capture CO 2 from the flue gas, and the calcination of CaCO 3 to regenerate the sorbent and produce concentrated CO 2 for storage. We describe the application to this concept to an existing (with today's technology) power plant. The added capture system incorporates a new supercritical steam cycle to take advantage of the large amount of heat coming out from the high temperature capture process (oxyfired combustion of coal is needed in the CaCO 3 calciner). In these conditions, the capture system is able to generate additional power (26.7% efficiency respect to LHV coal input to the calciner after accounting for all the penalties in the overall system), without disturbing the steam cycle of the reference plant (that retains its 44.9 efficiency). A preliminary cost study of the overall system, using well established analogues in the open literature for the main components, yields capture cost around 16 Euro /ton CO 2 avoided and incremental cost of electricity of just over 1 Euro /MW h e

Effect of calcination temperature on the structural, optical and magnetic properties of pure and Fe-doped ZnO nanoparticles

Directory of Open Access Journals (Sweden)

Pal Singh Raminder Preet

2016-06-01

Full Text Available In the present study, pure ZnO and Fe-doped ZnO (Zn0.97Fe0.03O nanoparticles were synthesized by simple coprecipitation method with zinc acetate, ferric nitrate and sodium hydroxide precursors. Pure ZnO and Fe-doped ZnO were further calcined at 450 °C, 600 °C and 750 °C for 2 h. The structural, morphological and optical properties of the samples were characterized by X-ray diffractometer (XRD, scanning electron microscope (SEM, energy dispersive spectroscopy (EDS and UV-Vis absorption spectroscopy. The X-ray diffraction studies revealed that the as-synthesized pure and doped ZnO nanoparticles have hexagonal wurtzite structure. The average crystallite size was calculated using Debye-Scherrer’s formula. The particle size was found to be in nano range and increased with an increase in calcination temperature. SEM micrographs confirmed the formation of spherical nanoparticles. Elemental compositions of various elements in pure and doped ZnO nanoparticles were determined by EDX spectroscopy. UV-Vis absorption spectra showed red shift (decrease in band gap with increasing calcination temperature. Effect of calcination on the magnetic properties of Fe-doped ZnO sample was also studied using vibrating sample magnetometer (VSM. M-H curves at room temperature revealed that coercivity and remanent polarization increase with an increase in calcination temperature from 450 °C to 750 °C, whereas reverse effect was observed for magnetization saturation.

Physical and chemical characteristics of fluorinel/sodium calcine generated during 30 cm Pilot-Plant Run 17

International Nuclear Information System (INIS)

Brewer, K.N.; Kessinger, G.F.; Littleton, L.L.; Olson, A.L.

1993-07-01

The 30 centimeter (cm) pilot plant calciner Run 17, of March 9, 1987, was performed to study the calcination of fluroinel-sodium blended waste blended at the ratio 3.5:1 fluorinel to sodium, respectively. The product of the run was analyzed by a variety of analytical techniques that included X-ray powder diffraction (XRD), inductively coupled plasma spectroscopy (ICP), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) to deduce physical and chemical characteristics. The analytical data, as well as data analyses and conclusions drawn from the data, are presented

Experimental determination of the energy levels of the antimony atom (Sb II), ions of the antimony (Sb II, Sb III), mercury (Hg IV) and cesium (Cs X)

International Nuclear Information System (INIS)

Arcimowicz, B.

1993-01-01

The thesis concerns establishing the energy scheme of the electronic levels, obtained from the analysis of the investigated spectra of antimony atom and ions (Sb I, Sb II, Sb III) and higher ionized mercury (Hg IV) and cesium (Cs X) atoms. The experimental studies were performed with optical spectroscopy methods. The spectra of the elements under study obtained in the spectral range from visible (680 nm) to vacuum UV (40 nm) were analysed. The classification and spectroscopic designation of the experimentally established 169 energy levels were obtained on the basis of the performed calculations and the fine structure analysis. The following configurations were considered: 5s 2 5p 2 ns, 5s 2 5p 2 n'd, 5s5p 4 of the antimony atom, 5s 2 5pns, 5s 2 5pn'd, 5s5p 3 of the ion Sb II, 5s 2 ns, 5s 2 n'd, 5s5p 2 of the on Sb III, 5d 8 6p of the ion Hg IV 4d 9 5s and 4d 9 5p Cs X. A reclassification was performed and some changes were introduced to the existing energy level scheme of the antimony atom, with the use of the information obtained from the absorption spectrum taken in the VUV region by the ''flash pyrolysis'' technique. The measurements of the hyperfine splittings in 19 spectral lines belonging to the antimony atom and ions additionally confirmed the assumed classification of the levels involved in these lines. The energy level scheme, obtained for Sb III, was compared to the other ones in the isoelectronic sequence starting with In I. On the basis of the analysis of the Hg IV spectrum it was proved that ground configuration of the three times ionized mercury atom is 5d 9 not 5d 8 6s as assumed until now. The fine structure, established from the analysis of the spectra of the elements under study was examined in multiconfiguration approximation. As a result of the performed calculations the fine structure parameters and wavefunctions were determined for the levels whose energy values were experimentally established in the thesis. (author). 140 refs, 22 figs, 17

The Influence of Growth Temperature on Sb Incorporation in InAsSb, and the Temperature-dependent Impact of Bi Surfactants

Science.gov (United States)

2014-01-01

temperature was set to give a beam equivalent pressure ( BEP ) of 4.8x10-7 Torr, as measured in this configuration. 10 4 We have shown in prior...to the value needed to grow lattice matched InAsSb on GaSb without using Bi surfactant at 415 C. The In growth rate was 1 m/hr. The Sb BEP was...1.2x10-7 Torr and the As BEP was 5.71x10-7 Torr. The absolute flux of all the constituents and the V/III ratios were kept constant for both layers of

Comparisons of TRAC-PF-1 calculations with semiscale Mod-3 small-break tests S-SB-P1 and S-SB-P7

International Nuclear Information System (INIS)

Sahota, M.S.

1982-01-01

Semiscale Tests S-SB-P1 and S-SB-P7 conducted in the Semiscale Mod-3 facility at the Idaho National Engineering Laboratory are analyzed using the latest released version of the Transient Reactor Analysis Code (TRAC-PF1). The results are used to assess TRAC-PF1 predictions of thermal-hydraulic phenomena and the effects of break size and pump operation on system response during slow transients. Tests S-SB-P1 and S-SB-P7 simulated an equivalent pressurized-water-reactor (PWR) 2.5% communicative cold-leg break for early and late pump trips, respectively, with only high-pressure injection (HPI) into the cold legs. The parameters examined include break flow, primary-system pressure response, primary-system mass distribution, and core characteristics

Method and apparatus for evaporating radioactive liquid and calcinating the residue

International Nuclear Information System (INIS)

Sridhar, T.S.

1984-01-01

This invention provides an apparatus and a process for evaporating liquid wastes and calcining the residue. The liquid is sprayed against a hollow, rotating heated cylinder within a casing. The dried residue is scraped from the rotating cylinder and released through a valve at the bottom of the casing, while the effluent gas is filtered

Prediction model of ammonium uranyl carbonate calcination by microwave heating using incremental improved Back-Propagation neural network

Energy Technology Data Exchange (ETDEWEB)

Li Yingwei [Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming, Yunnan Province 650093 (China); Key Laboratory of Unconventional Metallurgy, Ministry of Education, Kunming University of Science and Technology, Kunming, Yunnan Province 650093 (China); Peng Jinhui, E-mail: jhpeng@kmust.edu.c [Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming, Yunnan Province 650093 (China); Key Laboratory of Unconventional Metallurgy, Ministry of Education, Kunming University of Science and Technology, Kunming, Yunnan Province 650093 (China); Liu Bingguo [Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming, Yunnan Province 650093 (China); Key Laboratory of Unconventional Metallurgy, Ministry of Education, Kunming University of Science and Technology, Kunming, Yunnan Province 650093 (China); Li Wei [Key Laboratory of Unconventional Metallurgy, Ministry of Education, Kunming University of Science and Technology, Kunming, Yunnan Province 650093 (China); Huang Daifu [No. 272 Nuclear Industry Factory, China National Nuclear Corporation, Hengyang, Hunan Province 421002 (China); Zhang Libo [Faculty of Metallurgical and Energy Engineering, Kunming University of Science and Technology, Kunming, Yunnan Province 650093 (China); Key Laboratory of Unconventional Metallurgy, Ministry of Education, Kunming University of Science and Technology, Kunming, Yunnan Province 650093 (China)

2011-05-15

Research highlights: The incremental improved Back-Propagation neural network prediction model using the Levenberg-Marquardt algorithm based on optimizing theory is put forward. The prediction model of the nonlinear system is built, which can effectively predict the experiment of microwave calcining of ammonium uranyl carbonate (AUC). AUC can accept the microwave energy and microwave heating can quickly decompose AUC. In the experiment of microwave calcining of AUC, the contents of U and U{sup 4+} increased with increasing of microwave power and irradiation time, and decreased with increasing of the material average depth. - Abstract: The incremental improved Back-Propagation (BP) neural network prediction model was put forward, which was very useful in overcoming the problems, such as long testing cycle, high testing quantity, difficulty of optimization for process parameters, many training data probably were offered by the way of increment batch and the limitation of the system memory could make the training data infeasible, which existed in the process of calcinations for ammonium uranyl carbonate (AUC) by microwave heating. The prediction model of the nonlinear system was built, which could effectively predict the experiment of microwave calcining of AUC. The predicted results indicated that the contents of U and U{sup 4+} were increased with increasing of microwave power and irradiation time, and decreased with increasing of the material average depth.

Influence of calcination temperature on sol-gel synthesized single-phase bismuth titanate for high dielectric capacitor applications

Energy Technology Data Exchange (ETDEWEB)

Thiruramanathan, Pandirengan; Marikani, Arumugam [Mepco Schlenk Engineering College, Tamil Nadu (India). Dept. of Physics; Madhavan, Durairaj [Mepco Schlenk Engineering College, Tamil Nadu (India). Dept. of Chemistry; Bharadwaj, Suresh; Awasthi, Anand Mohan [UGC-DAE Consortium for Scientific Research, Indore (India). Thermodynamics Lab.

2016-05-15

An inexpensive sol-gel combustion method using citric acid as fuel has been used to synthesize bismuth titanate, Bi{sub 4}Ti{sub 3}O{sub 12} nanopowders. Thermogravimetric analysis proved that a calcination temperature of 900 C is sufficient for the preparation of single-phase bismuth titanate. X-ray diffraction and Fourier transform infrared spectroscopy are used to examine the influence of calcination temperature on the structural growth of the Bi{sub 4}Ti{sub 3}O{sub 12} nanopowder. The average crystallite size estimated by using the Scherrer method and the Williamson-Hall method was found to increase with calcination temperature. Photoluminescence behavior as a function of calcination temperature was observed at two different excitation wavelengths of 300 nm and 420 nm. The morphology of the particles analyzed using images obtained from field emission scanning electron microscopy displayed irregular, random sized, and spherical-shaped structures. The stoichiometry and purity of the nanopowder are confirmed by energy-dispersive spectroscopy. The broadband dielectric results established the highest dielectric constant (ε{sub r} = 450) for a frequency of 100 Hz achieved with a potential capacitance of 138 pF m{sup -2}. This establishes Bi{sub 4}Ti{sub 3}O{sub 12} as a promising dielectric material for achieving high energy density capacitors for the next-generation passive devices.

Prediction model of ammonium uranyl carbonate calcination by microwave heating using incremental improved Back-Propagation neural network

International Nuclear Information System (INIS)

Li Yingwei; Peng Jinhui; Liu Bingguo; Li Wei; Huang Daifu; Zhang Libo

2011-01-01

Research highlights: → The incremental improved Back-Propagation neural network prediction model using the Levenberg-Marquardt algorithm based on optimizing theory is put forward. → The prediction model of the nonlinear system is built, which can effectively predict the experiment of microwave calcining of ammonium uranyl carbonate (AUC). → AUC can accept the microwave energy and microwave heating can quickly decompose AUC. → In the experiment of microwave calcining of AUC, the contents of U and U 4+ increased with increasing of microwave power and irradiation time, and decreased with increasing of the material average depth. - Abstract: The incremental improved Back-Propagation (BP) neural network prediction model was put forward, which was very useful in overcoming the problems, such as long testing cycle, high testing quantity, difficulty of optimization for process parameters, many training data probably were offered by the way of increment batch and the limitation of the system memory could make the training data infeasible, which existed in the process of calcinations for ammonium uranyl carbonate (AUC) by microwave heating. The prediction model of the nonlinear system was built, which could effectively predict the experiment of microwave calcining of AUC. The predicted results indicated that the contents of U and U 4+ were increased with increasing of microwave power and irradiation time, and decreased with increasing of the material average depth.

Chloride adsorption by calcined layered double hydroxides in hardened Portland cement paste

KAUST Repository

Yoon, Seyoon; Moon, Juhyuk; Bae, Sungchul; Duan, Xiaonan; Giannelis, Emmanuel P.; Monteiro, Paulo M.

2014-01-01

This study investigated the feasibility of using calcined layered double hydroxides (CLDHs) to prevent chloride-induced deterioration in reinforced concrete. CLDHs not only adsorbed chloride ions in aqueous solution with a memory effect but also had

Influence of calcination process on the formation of selected air pollutants

Directory of Open Access Journals (Sweden)

Wydrych Jacek

2017-01-01

Full Text Available The subject of the study is to analyze the phenomena of thermal flow in the precalcinator chamber of the exchanger's furnace tower including the combustion of coal dust and decarbonisation of raw lime powder. During the research were provided development of a mathematical model of particulate solid fuels combustion, calcining the raw material, NOx and COx formation. Moreover conducting the number for the current and the upgraded design of the precalcinator and analysis of the results. In this study, a mathematical model based on Euler's method to describe the motion of the gas phase and the Lagrange method to describe the motion of particles [1-4]. In the calculations there were assumed fractional particles raw material and fuel, and the following processes: flow of exhaust gases from the rotary kiln through the precalcinator chamber, heat exchange between the particles of raw material and exhaust gases, the additional fuel combustion in the precalcinator, the process of raw material calcination, transformation of gaseous substances, effect of the additional (tertiary air delivery on the processes in the chamber.

Memory effect of calcined layered samarium hydroxy chlorides in aqueous solution

International Nuclear Information System (INIS)

Lee, Byung Il; Byeon, Song Ho

2015-01-01

The decomposition and recovery behavior of layered samarium hydroxychloride (Sm 2 (OH) 5 Cl·nH 2 O, LSmH) has been closely studied in various conditions. Although the heat treatment of LSmH at 700 °C completely collapsed typical layered structure, the calcined LSmH (c-LSmH) recovered its layered characteristics and consequently its ability to intercalate anions into the interlayer space when it was rehydroxylated and rehydrated in aqueous solutions containing organic and inorganic anions. This phenomenon is similar to the memory effect observed in classical layered double hydroxides (LDHs), where LDHs calcined to a mixture of metal oxides can recover their layered structures in aqueous solutions. In contrast, the recovery reaction of c-LSmH in water without any counter anions was unsuccessful and instead resulted in the formation of Sm(OH) 3 . Such a difference was interpreted on the basis of the salt effect on Sm 2 (OH) 5 Cl·nH 2 O–Sm(OH) 3 phase equilibria in water

Evaluation of blends bauxite-calcination-method red mud with other industrial wastes as a cementitious material: Properties and hydration characteristics

International Nuclear Information System (INIS)

Zhang Na; Liu Xiaoming; Sun Henghu; Li Longtu

2011-01-01

Red mud is generated from alumina production, and its disposal is currently a worldwide problem. In China, large quantities of red mud derived from bauxite calcination method are being discharged annually, and its utilization has been an urgent topic. This experimental research was to evaluate the feasibility of blends red mud derived from bauxite calcination method with other industrial wastes for use as a cementitious material. The developed cementitious material containing 30% of the bauxite-calcination-method red mud possessed compressive strength properties at a level similar to normal Portland cement, in the range of 45.3-49.5 MPa. Best compressive strength values were demonstrated by the specimen RSFC2 containing 30% bauxite-calcination-method red mud, 21% blast-furnace slag, 10% fly ash, 30% clinker, 8% gypsum and 1% compound agent. The mechanical and physical properties confirm the usefulness of RSFC2. The hydration characteristics of RSFC2 were characterized by XRD, FTIR, 27 Al MAS-NMR and SEM. As predominant hydration products, ettringite and amorphous C-S-H gel are principally responsible for the strength development of RSFC2. Comparing with the traditional production for ordinary Portland cement, this green technology is easier to be implemented and energy saving. This paper provides a key solution to effectively utilize bauxite-calcination-method red mud.

Sulfation of CaO particles in a carbonation/calcination loop to capture CO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Grasa, G.S.; Alonso, M.; Abanades, J.C. [CSIC, Zaragoza (Spain)

2008-03-15

CaO is being proposed as a regenerable sorbent of CO{sub 2} via a carbonation/calcination loop. It is well known that natural sorbents lose their capacity to capture CO{sub 2} with the number of cycles due to textural degradation. In coal combustion systems, reaction with the SO{sub 2} present in flue gases also causes sorbent deactivation. This work investigates the effect of partial sorbent sulfation on the amount of CaO used in systems where both carbonation and sulfation reactions are competing. We have found that SO{sub 2} reacts with the deactivated CaO resulting from repetitive calcination/carbonation reactions. Therefore, the deactivation of CaO as a result of the presence of SO{sub 2} is lower than one would expect if one assumes that SO{sub 2} reacts only with active CaO. This work shows that changes in the texture of the sorbent due to repetitive carbonation/calcination cycles tend to increase the sulfation capacity of the sorbents tested. This suggests that the purge of deactivated CaO obtained from a CO{sub 2} capture loop could be a more effective sorbent of SO{sub 2} than fresh CaO.

Study on Al2O3 extraction from activated coal gangue under different calcination atmospheres

Science.gov (United States)

Dong, Ling; Liang, Xinxing; Song, Qiang; Gao, Gewu; Song, Lihua; Shu, Yuanfeng; Shu, Xinqian

2017-12-01

Coal gangue was calcinated under air, nitrogen, carbon dioxide, air-hydrogen, and hydrogen atmospheres. The effects of different calcination temperatures and atmospheres on the mineral composition of activated coal gangue were investigated by X-ray diffraction. Moreover, the acid leaching kinetics of aluminum oxide from coal gangue was investigated with sulfuric acid. It showed that the air atmosphere promoted kaolinite decomposition during coal gangue calcination. The hydrogen atmosphere promoted the activation and decomposition of kaolinite at reaction temperatures exceeding 650°C. The carbon dioxide atmosphere eliminated the influence of residual carbon on coal gangue. When the ratio of acid/coal gangue was 1.5 and reaction temperature was 650°C, the sulfuric acid leaching rate under air, air-hydrogen, carbon dioxide, hydrogen and nitrogen atmospheres were 93.66%, 90.90%, 84.06%, 81.91% and 77.54% respectively. The acid leaching reaction process conformed to unreacted shrinking core model of particle unchanged, and was controlled by the interfacial chemical reaction. The reaction kinetic equation for the leaching process was 1-(1-x)1/3=kt with an apparent activation energy of 48.97 kJ/mol.

Self-organized formation of GaSb/GaAs quantum rings.

Science.gov (United States)

Timm, R; Eisele, H; Lenz, A; Ivanova, L; Balakrishnan, G; Huffaker, D L; Dähne, M

2008-12-19

Ring-shaped GaSb/GaAs quantum dots, grown by molecular beam epitaxy, were studied using cross-sectional scanning tunneling microscopy. These quantum rings have an outer shape of a truncated pyramid with baselengths around 15 nm and heights of about 2 nm but are characterized by a clear central opening extending over about 40% of the outer baselength. They form spontaneously during the growth and subsequent continuous capping of GaSb/GaAs quantum dots due to the large strain and substantial As-for-Sb exchange reactions leading to strong Sb segregation.

Quaternary InGaAsSb Thermophotovoltaic Diodes

International Nuclear Information System (INIS)

MW Dashiell; JF Beausang; H Ehsani; GJ Nichols; DM Depoy; LR Danielson; P Talamo; KD Rahner; EJ Brown; SR Burger; PM Foruspring; WF Topper; PF Baldasaro; CA Wang; R Huang; M Connors; G Turner; Z Shellenbarger; G Taylor; J Li; R Martinelli; D Donetski; S Anikeev; G Belenky; S Luryi

2006-01-01

In x Ga 1-x As y Sb 1-y thermophotovoltaic (TPV) diodes were grown lattice-matched to GaSb substrates by Metal Organic Vapor Phase Epitaxy (MOVPE) in the bandgap range of E G = 0.5 to 0.6eV. InGaAsSb TPV diodes, utilizing front-surface spectral control filters, are measured with thermal-to-electric conversion efficiency and power density of η TPV = 19.7% and PD =0.58 W/cm 2 respectively for a radiator temperature of T radiator = 950 C, diode temperature of T diode = 27 C, and diode bandgap of E G = 0.53eV. Practical limits to TPV energy conversion efficiency are established using measured recombination coefficients and optical properties of front surface spectral control filters, which for 0.53eV InGaAsSb TPV energy conversion is η TPV = 28% and PD = 0.85W/cm 2 at the above operating temperatures. The most severe performance limits are imposed by (1) diode open-circuit voltage (VOC) limits due to intrinsic Auger recombination and (2) parasitic photon absorption in the inactive regions of the module. Experimentally, the diode V OC is 15% below the practical limit imposed by intrinsic Auger recombination processes. Analysis of InGaAsSb diode electrical performance vs. diode architecture indicate that the V OC and thus efficiency is limited by extrinsic recombination processes such as through bulk defects

Effect of Sb Segregation on Conductance and Catalytic Activity at Pt/Sb-Doped SnO2 Interface: A Synergetic Computational and Experimental Study

DEFF Research Database (Denmark)

Hu, Qiang; Colmenares Rausseo, Luis César; Martinez, Umberto

2015-01-01

a combined computational and experimental study. It was found that Sb-dopant atoms prefer to segregate toward the ATO/Pt interface. The deposited Pt catalysts, interestingly, not only promote Sb segregation, but also suppress the occurrence of Sb3+ species, a charge carrier neutralizer at the interface...... to support future applications of ATO/Pt-based materials as possible cathodes for PEMFC applications with enhanced durability under practical applications....

Thermoelectric and mechanical properties of spark plasma sintered Cu{sub 3}SbSe{sub 3} and Cu{sub 3}SbSe{sub 4}: Promising thermoelectric materials

Energy Technology Data Exchange (ETDEWEB)

Tyagi, Kriti; Gahtori, Bhasker; Bathula, Sivaiah; Toutam, Vijaykumar; Sharma, Sakshi; Singh, Niraj Kumar; Dhar, Ajay, E-mail: adhar@nplindia.org [CSIR-Network of Institutes for Solar Energy, Materials Physics and Engineering, CSIR-National Physical Laboratory, Dr. K. S. Krishnan Road, New Delhi 110012 (India)

2014-12-29

We report the synthesis of thermoelectric compounds, Cu{sub 3}SbSe{sub 3} and Cu{sub 3}SbSe{sub 4}, employing the conventional fusion method followed by spark plasma sintering. Their thermoelectric properties indicated that despite its higher thermal conductivity, Cu{sub 3}SbSe{sub 4} exhibited a much larger value of thermoelectric figure-of-merit as compared to Cu{sub 3}SbSe{sub 3}, which is primarily due to its higher electrical conductivity. The thermoelectric compatibility factor of Cu{sub 3}SbSe{sub 4} was found to be ∼1.2 as compared to 0.2 V{sup −1} for Cu{sub 3}SbSe{sub 3} at 550 K. The results of the mechanical properties of these two compounds indicated that their microhardness and fracture toughness values were far superior to the other competing state-of-the-art thermoelectric materials.

Remote process connectors for the new waste calcining facility

International Nuclear Information System (INIS)

Jacobs, R.T.; Carter, J.A.; Hohback, A.C.

1978-01-01

The remote process connectors developed, used, and tested at the Remote Maintenance Development Facility are described. These connectors, including the three-bolt kinematic-graphite flange and watertight electrical connectors, are assembled on master jigs (holding-welding fixture) to form interchangeable pump and valve loop assemblies. These assemblies, with their guide-in platforms, make possible a method of performing remote maintenance at the New Waste Calcining Facility which is a departure from methods that until now have been the standard of the industry

Separation of non-hazardous, non-radioactive components from ICPP calcine via chlorination

International Nuclear Information System (INIS)

Nelson, L.O.

1995-05-01

A pyrochemical treatment method for separating non-radioactive from radioactive components in solid granular waste accumulated at the Idaho Chemical Processing Plant was investigated. The goal of this study was to obtain kinetic and chemical separation data on the reaction products of the chlorination of the solid waste, known as calcine. Thermodynamic equilibrium calculations were completed to verify that a separation of radioactive and non-radioactive calcine components was possible. Bench-scale chlorination experiments were completed subsequently in a variety of reactor configurations including: a fixed-bed reactor (reactive gases flowed around and not through the particle bed), a packed/fluidized-bed reactor, and a packed-bed reactor (reactive gases flowed through the particle bed). Chemical analysis of the reaction products generated during the chlorination experiments verified the predictions made by the equilibrium calculations. An empirical first-order kinetic rate expression was developed for each of the reactor configurations. 20 refs., 16 figs., 21 tabs

Synthesis of aluminum oxide by the polymer precursor method (Pechini) in 4: 1 ratio of citric acid: metal cation: calcination temperature effect

International Nuclear Information System (INIS)

Silva, M.C.; Lira, H.L.; Ribeiro, P.C.; Freitas, N.L.

2014-01-01

The technology field is nanopowders prominent in science since these materials fall in various sectors regarding their applications. This work aims at the synthesis of aluminum oxide by polymeric precursors in 4:1 ratio of citric acid:metal cation and evaluate the influence of calcination temperature on their structural and morphological characteristics. The samples after reaction were characterized by XRD and thermal analysis. After calcination 500-1200°C the samples were characterized by XRD, SEM and particle size distribution. The results showed that the variation of the calcination temperature is sufficient to achieve a same material with different structural and morphological characteristics. The most stable phase aluminum oxide arose only after calcination at 1100°C, below 900°C, the amorphous material appeared. As regards the morphology, the change was not as significant as compared to the structure. (author)

Biocompatibility of GaSb thin films grown by RF magnetron sputtering

Science.gov (United States)

Nishimoto, Naoki; Fujihara, Junko; Yoshino, Katsumi

2017-07-01

GaSb may be suitable for biological applications, such as cellular sensors and bio-medical instrumentation because of its low toxicity compared with As (III) compounds and its band gap energy. Therefore, the biocompatibility and the film properties under physiological conditions were investigated for GaSb thin films with or without a surface coating. GaSb thin films were grown on quartz substrates by RF magnetron sputtering, and then coated with (3-mercaptopropyl) trimethoxysilane (MPT). The electrical properties, surface morphology, and crystal structure of the GaSb thin film were unaffected by the MPT coating. The cell viability assay suggested that MPT-coated GaSb thin films are biocompatible. Bare GaSb was particularly unstable in pH9 buffer. Ga elution was prevented by the MPT coating, although the Ga concentration in the pH 9 buffer was higher than that in the other solutions. The surface morphology and crystal structure were not changed by exposure to the solutions, except for the pH 9 buffer, and the thin film properties of MPT-coated GaSb exposed to distilled water and H2O2 in saline were maintained. These results indicate that MPT-coated GaSb thin films are biocompatible and could be used for temporary biomedical devices.

New DC conductivity spectra of Zn–Al layered double hydroxide (Zn–Al–NO3–LDH and its calcined product of ZnO phase

Directory of Open Access Journals (Sweden)

Abdullah Ahmed Ali Ahmed

2017-05-01

Full Text Available Zn–Al–NO3–LDH nanostructure was synthesized via the coprecipitation method at molar ratio Zn2+/Al3+ = 4 and pH = 7. The resultant sample was thermally treated at calcined temperatures of 50, 100, 150, 200, 250 and 300 °C. The layered structure of the Zn–Al–NO3–LDH samples was stable below the calcination temperature 200 °C as shown in powder X-ray diffraction (PXRD patterns of calcined samples. The calcination products showed a collapse of LDH structure and ZnO phase was formed at 200 °C and above. The dielectric spectroscopy of LDH was explained using anomalous low frequency dispersion (ALFD due to the low mobility of LDH carriers. The conductivity spectra of LDH can be theoretically described according to the effective phase within the calcination products of LDH. In the comparison with previously researches, this study presented higher values of DC conductivity for all studied samples.

Effect of aluminum and silicon reactants and process parameters on glass-ceramic waste form characteristics for immobilization of high-level fluorinel-sodium calcined waste

International Nuclear Information System (INIS)

Vinjamuri, K.

1993-06-01

In this report, the effects of aluminum and silicon reactants, process soak time and the initial calcine particle size on glass-ceramic waste form characteristics for immobilization of the high-level fluorinel-sodium calcined waste stored at the Idaho Chemical Processing Plant (ICPP) are investigated. The waste form characteristics include density, total and normalized elemental leach rates, and microstructure. Glass-ceramic waste forms were prepared by hot isostatically pressing (HIPing) a pre-compacted mixture of pilot plant fluorinel-sodium calcine, Al, and Si metal powders at 1050 degrees C, 20,000 psi for 4 hours. One of the formulations with 2 wt % Al was HIPed for 4, 8, 16 and 24 hours at the same temperature and pressure. The calcine particle size range include as calcined particle size smaller than 600 μm (finer than -30 mesh, or 215 μm Mass Median Diameter, MMD) and 180 μm (finer than 80 mesh, or 49 μm MMD)

Sulfuric Acid Corrosion of Low Sb - Pb Battery Alloys | Ntukogu ...

African Journals Online (AJOL)

The corrosion properties of low Sb - Pb alloys developed for maintenance free motive power industrial batteries was studied by a bare grid constant current method and compared to those of the conventional Pb- 6% Sb alloy. Low Sb-Pb alloys with Se and As grain refiners were found to have higher corrosion rates than the ...

The system analysis of temperature and melting enthalpy of intermetallic compounds of antimony-lanthanoids system of Sb Ln, Sb2Ln composition

International Nuclear Information System (INIS)

Badalova, M.A.; Chamanova, M.; Dodkhoev, E.S.; Badalov, A.; Abdusalyamova, M.N.

2015-01-01

Present article is devoted to system analysis of temperature and melting enthalpy of intermetallic compounds of antimony-lanthanoids system of Sb Ln, Sb 2 Ln composition. The melting enthalpy was estimated. The temperature value was determined.

Bonding in ZnSb

DEFF Research Database (Denmark)

Bjerg, Lasse; Madsen, Georg K. H.; Iversen, Bo Brummerstedt

Thermoelectric materials are capable of converting waste heat into usable electric energy. The conversion efficiency depends critically on the electronic band structure. Theoretical calculations predict the semiconducting ZnSb to have a promising efficiency if it is n-doped. The details of the lo......Thermoelectric materials are capable of converting waste heat into usable electric energy. The conversion efficiency depends critically on the electronic band structure. Theoretical calculations predict the semiconducting ZnSb to have a promising efficiency if it is n-doped. The details...... of the lowest conduction band have therefore been investigated. Electrons placed in the lowest conduction band are predicted to increase the bonding between second nearest neighbour atoms. This causes a lowering of the energy at special points in the first Brillouin zone. Thereby, the dispersion of the lowest...

Preparation and Characterization of Au/Pd Modified-TiO2 Photocatalysts for Phenol and Toluene Degradation under Visible Light—The Effect of Calcination Temperature

Directory of Open Access Journals (Sweden)

Anna Cybula

2014-01-01

Full Text Available Rutile loaded with Au/Pd nanoparticles was prepared using a water-in-oil microemulsion system of water/AOT/cyclohexane followed by calcination. The effect of calcination temperature (from 350 to 700°C on the structure of Au/Pd nanoparticles deposited at rutile matrix and the photocatalytic properties of Au/Pd-TiO2 was investigated in two model reactions (toluene degradation in gas phase and phenol degradation in aqueous phase. Toluene was irradiated over Au/Pd-TiO2 using light emitting diodes (LEDs, λmax⁡ = 415 nm. The sample 0.5 mol% Pd/TiO2 exhibited the highest activity under visible light irradiation in gas and aqueous phase reaction among all photocatalysts calcined at 350°C, while the sample modified only with gold nanoparticles showed the lowest activity. The Au/Pd-TiO2 sample calcinated at 350°C possesses the highest photocatalytic activity when degrading phenol under visible light, which is 14 times higher than that of the one calcinated at 450°C. It was observed that increasing temperature from 350 to 700°C during calcination step caused segregation of metals and finally resulted in photoactivity drop.

Are Sb4n (n>1) clusters weakly interacting tetrahedra?

International Nuclear Information System (INIS)

Kumar, V.

1993-03-01

The electronic and atomic structure of Sb 4 and Sb 8 clusters is studied using the ab-initio molecular dynamics method in the local density approximation. While for Sb 4 we obtain a regular tetrahedron to be about 2.0 eV lower in energy than a bent rhombus, for Sb 8 two structures, (1) two weakly interaction tetrahedra and (2) a bent rhombus interacting with a stretched tetrahedron, obtained from the simulated annealing lie only within about 0.1 eV indicating the importance of the bent rhombus structure for larger clusters. As compared to two isolated tetrahedra, the binding energy of Sb 8 is about 0.5 eV. Our results are thus in excellent agreement with the experimental data which show predominantly the abundance of tetramers above room temperature. (author). 18 refs, 5 figs, 1 tab

Synthesis and antibacterial evaluation of calcinated Ag-doped nano-hydroxyapatite with dispersibility.

Science.gov (United States)

Furuzono, Tsutomu; Motaharul, Mazumder; Kogai, Yasumichi; Azuma, Yoshinao; Sawa, Yoshiki

2015-05-01

Dispersible hydroxyapatite (HAp) nanoparticles are very useful for applying a monolayer to implantable medical devices using the nano-coating technique. To improve tolerance to infection on implanted medical devices, silver-doped HAp (Ag-HAp) nanoparticles with dispersiblity and crystallinity were synthesized, avoiding calcination-induced sintering, and evaluated for antibacterial activity. The Ca10-xAgx(PO4)6(OH)2 with x = 0 and 0.2 were prepared by wet chemical processing at 100°C. Before calcination at 700°C for 2 h, two kinds of anti-sintering agents, namely a Ca(NO3)2 (Ca salt) and a polyacrylic acid/Ca salt mixture (PAA-Ca), were used. Escherichia coli was used to evaluate the antibacterial activity of the nanopowder. When PAA-Ca was used as an anti-sintering agent in calcination to prepare the dispersible nanoparticles, strong metallic Ag peaks were observed at 38.1° and 44.3° (2θ) in the X-ray diffraction (XRD) profile. However, the Ag peak was barely observed when Ca salt was used alone as the anti-sintering agent. Thus, using Ca salt alone was more effective for preparation of dispersible Ag-HAp than PAA-Ca. The particle average size of Ag-HAp with 0.5 mol% of Ag content was found to be 325 ± 70 nm when the formation of large particleaggregations was prevented, as determined by dynamic light scattering instrument. The antibacterial activity of the Ag-HAp nanoparticles possessing 0.5 mol% against E. coli was greater than 90.0%. Dispersible and crystalline nano Ag-HAp can be obtained by using Ca salt alone as an anti-sintering agent. The nanoparticles showed antibacterial activity.

Epitaxial Growth and Electronic Structure of Half Heuslers Co1-xNixTiSb (001), Ni1-xCoxTiSn, and PtLuSb

Science.gov (United States)

2016-01-09

lineup of CoTiSb with conventional III/V’s, the valence-band discontinuities in abrupt CoTiSb/InGaAs(001) and CoTiSb/InAlAs(001) heterojunctions were...confirm identification of a topological surface state: first, the state must be confined and show no out-of-plane dispersion; second, the state

Effect of calcinations temperature of CuO nanoparticle on the kinetics of decontamination and decontamination products of sulphur mustard.

Science.gov (United States)

Mahato, T H; Singh, Beer; Srivastava, A K; Prasad, G K; Srivastava, A R; Ganesan, K; Vijayaraghavan, R

2011-09-15

Present study investigates the potential of CuO nanoparticles calcined at different temperature for the decontamination of persistent chemical warfare agent sulphur mustard (HD) at room temperature (30 ± 2 °C). Nanoparticles were synthesized by precipitation method and characterized by using SEM, EDAX, XRD, and Raman Spectroscopy. Synthesized nanoparticles were tested as destructive adsorbents for the degradation of HD. Reactions were monitored by GC-FID technique and the reaction products characterized by GC-MS. It was observed that the rate of degradation of HD decreases with the increase in calcination temperature and there is a change in the percentage of product of HD degradation. GC-MS data indicated that the elimination product increases with increase in calcination temperature whereas the hydrolysis product decreases. Copyright © 2011 Elsevier B.V. All rights reserved.

Advanced fluid bed calciner information on IR-100 award

International Nuclear Information System (INIS)

Druby, M.C.; Owen, T.J.; Klem, M.J.

1986-01-01

The advanced fluidized bed calciner provides time, temperature and turbulence to change a liquid slurry such as ammonium diuranate into a uranium dioxide powder. The liquid is sprayed into a hot chamber (up to 700 0 C) which includes thousands of tiny metal beads, about the size of BB's. The constantly moving beads provide an efficient heat transfer media for the immediate transformation of the slurry droplets into dry particles of powder, which are carried out by hot nitrogen gas and recovered in a collector

Effects of FeSb6 octahedral deformations on the electronic structure of LaFe4Sb12

KAUST Repository

Pulikkotil, Jiji Thomas Joseph

2011-09-01

First-principles density functional based electronic structure calculations are performed in order to clarify the influence of FeSb6 octahedral deformations on the structural and electronic structure properties of LaFe 4Sb12. Our results show that octahedral tiltings correlate with the band dispersions and, consequently, the band masses. While total energy variation points at an enhanced role of lattice anharmonicity, flat bands emerge from a redistribution of the electronic states. © 2011 Elsevier B.V. All rights reserved.

Two-band superlinear electroluminescence in GaSb based nanoheterostructures with AlSb/InAs.sub.1-x./sub.Sb.sub.x./sub./AlSb deep quantum well

Czech Academy of Sciences Publication Activity Database

Mikhailova, M. P.; Ivanov, E.V.; Danilov, L.V.; Petukhov, A.A.; Kalinina, K.V.; Slobozhanyuk, S.I.; Zegrya, G.G.; Stoyanov, N. D.; Yakovlev, Yu. P.; Hospodková, Alice; Pangrác, Jiří; Oswald, Jiří; Zíková, Markéta; Hulicius, Eduard

2014-01-01

Roč. 115, č. 22 (2014), "223102-1"-"223102-5" ISSN 0021-8979 R&D Projects: GA ČR GA13-15286S Institutional support: RVO:68378271 Keywords : MOVPE * GaSb * InAs * electroluminescence * quantum well Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 2.183, year: 2014