WorldWideScience

Sample records for hf soluble part

  1. Issues concerning the determination of solubility products of sparingly soluble crystalline solids. Solubility of HfO2(cr)

    International Nuclear Information System (INIS)

    Rai, Dhanpat; Kitamura, Akira; Rosso, Kevin M.; Sasaki, Takayuki; Kobayashi, Taishi

    2016-01-01

    Solubility studies were conducted with HfO 2 (cr) solid as a function HCl and ionic strength ranging from 2.0 to 0.004 mol kg -1 . These studies involved (1) using two different amounts of the solid phase, (2) acid washing the bulk solid phase, (3) preheating the solid phase to 1400 C, and (4) heating amorphous HfO 2 (am) suspensions to 90 C to ascertain whether the HfO 2 (am) converts to HfO 2 (cr) and to determine the solubility from the oversaturation direction. Based on the results of these treatments it is concluded that the HfO 2 (cr) contains a small fraction of less crystalline, but not amorphous, material [HfO 2 (lcr)] and this, rather than the HfO 2 (cr), is the solubility-controlling phase in the range of experimental variables investigated in this study. The solubility data are interpreted using both the Pitzer and SIT models and they provide log 10 K 0 values of -(59.75±0.35) and -(59.48±0.41), respectively, for the solubility product of HfO 2 (lcr)[HfO 2 (lcr) + 2H 2 O ↔ Hf 4+ + 4OH - ]. The log 10 of the solubility product of HfO 2 (cr) is estimated to be < -63. The observation of a small fraction of less crystalline higher solubility material is consistent with the general picture that mineral surfaces are often structurally and/or compositionally imperfect leading to a higher solubility than the bulk crystalline solid. This study stresses the urgent need, during interpretation of solubility data, of taking precautions to make certain that the observed solubility behavior for sparingly-soluble solids is assigned to the proper solid phase.

  2. Issues concerning the determination of solubility products of sparingly soluble crystalline solids. Solubility of HfO{sub 2}(cr)

    Energy Technology Data Exchange (ETDEWEB)

    Rai, Dhanpat [Rai Enviro-Chem, LLC, Yachats, OR (United States); Kitamura, Akira [Japan Atomic Energy Agency, Ibaraki (Japan); Rosso, Kevin M. [Pacific Northwest National Laboratory, Richland, WA (United States); Sasaki, Takayuki; Kobayashi, Taishi [Kyoto Univ. (Japan)

    2016-11-01

    Solubility studies were conducted with HfO{sub 2}(cr) solid as a function HCl and ionic strength ranging from 2.0 to 0.004 mol kg{sup -1}. These studies involved (1) using two different amounts of the solid phase, (2) acid washing the bulk solid phase, (3) preheating the solid phase to 1400 C, and (4) heating amorphous HfO{sub 2}(am) suspensions to 90 C to ascertain whether the HfO{sub 2}(am) converts to HfO{sub 2}(cr) and to determine the solubility from the oversaturation direction. Based on the results of these treatments it is concluded that the HfO{sub 2}(cr) contains a small fraction of less crystalline, but not amorphous, material [HfO{sub 2}(lcr)] and this, rather than the HfO{sub 2}(cr), is the solubility-controlling phase in the range of experimental variables investigated in this study. The solubility data are interpreted using both the Pitzer and SIT models and they provide log{sub 10} K{sup 0} values of -(59.75±0.35) and -(59.48±0.41), respectively, for the solubility product of HfO{sub 2}(lcr)[HfO{sub 2}(lcr) + 2H{sub 2}O ↔ Hf{sup 4+} + 4OH{sup -}]. The log{sub 10} of the solubility product of HfO{sub 2}(cr) is estimated to be < -63. The observation of a small fraction of less crystalline higher solubility material is consistent with the general picture that mineral surfaces are often structurally and/or compositionally imperfect leading to a higher solubility than the bulk crystalline solid. This study stresses the urgent need, during interpretation of solubility data, of taking precautions to make certain that the observed solubility behavior for sparingly-soluble solids is assigned to the proper solid phase.

  3. Solubility Part 1

    NARCIS (Netherlands)

    Tantra, Ratna; Bolea, Eduardo; Bouwmeester, H.; Rey-Castro, Carlos; David, C.A.A.; Dogné, Jean Michel; Laborda, Francisco; Laloy, Julie; Robinson, Kenneth N.; Undas, A.K.; Zande, van der M.

    2016-01-01

    This chapter gives an overview of different methods that can potentially be used to determine the solubility of nanomaterials. In general, the methods presented can be broadly divided into four categories: separation methods, methods to quantify free ions, methods to quantify total dissolved

  4. The CaO-TiO2-ZrO2 system at 1,200 degree C and the solubilities of Hf and Gd in zirconolite

    International Nuclear Information System (INIS)

    Swenson, D.; Nieh, T.G.; Fournelle, J.H.

    1995-12-01

    In recent years, significant technological advancements have been made in the Synroc scheme for the immobilization high-level nuclear waste. However, many basic scientific issues related to Synroc fabrication have yet to be addressed. The CaO-TiO 2 -ZrO 2 system is an integral part of the Synroc formulation. Phase equilibria are established in the CaO-TiO 2 -ZrO 2 system at 1,200 C, using X-ray diffraction and electron probe microanalysis. The existence of two previously reported ternary phases, zirconolite (CaZrTi 2 O 7 ) and calzirtite (Ca 2 Zr 5 Ti 2 O 16 ), is confirmed. Each of these phases exhibits a significant range of homogeneity between TiO 2 and ZrO 2 while maintaining a nearly constant concentration of CaO. The ternary solubilities of the constituent binary phases are found to be negligible, with the exceptions of the perovskites, which display mutual solubility of at least 22 mol.% and may in fact form a series of continuous solid solutions. The solubilities of Hf and Gd in zirconolite are also investigated. While Hf-bearing samples did not reach thermodynamic equilibrium under the experimental conditions employed, the existence of a Hf analog to zirconolite, CaHfTi 2 O 7 , is conclusively demonstrated. The phase is stable at the stoichiometric composition, and its lattice parameters are very close to those reported in the literature for stoichiometric zirconolite. A Gd-bearing sample of the composition Ca 0.88 Zr 0.88 Gd 9.24 Ti 2 O 7 is found to be essentially single phase zirconolite, in agreement with previous investigations at higher temperatures

  5. A thermodynamic model for the solubility of HfO{sub 2}(am) in the aqueous K{sup +} - HCO{sub 3}{sup -} - CO{sub 3}{sup 2-} - OH{sup -} - H{sub 2}O system

    Energy Technology Data Exchange (ETDEWEB)

    Rai, Dhanpat [Rai Enviro-Chem, LLC, Yachats, OR (United States); Kitamura, Akira [Japan Atomic Energy Agency, Tokai (Japan); Rosso, Kevin M. [Pacific National Laboratory, Richland, WA (United States)

    2017-10-01

    Solubility of HfO{sub 2}(am) was determined as a function of KHCO{sub 3} concentrations ranging from 0.001 mol.kg{sup -1} to 0.1 mol.kg{sup -1}. The solubility of HfO{sub 2}(am) increased dramatically with the increase in KHCO{sub 3} concentrations, indicating that Hf(IV) makes strong complexes with carbonate. Thermodynamic equilibrium constants for the formation of Hf-carbonate complexes were determined using both the Pitzer and SIT models. The dramatic increase in Hf concentrations with the increase in KHCO{sub 3} concentrations can best be described by the formation of Hf(OH{sup -}){sub 2}(CO{sub 3}){sub 2}{sup 2-} and Hf(CO{sub 3}){sub 5}{sup 6-}. The log{sub 10} K{sup 0} values for the reactions [Hf{sup 4+}+2CO{sub 3}{sup 2-}+2OH{sup -}↔Hf(OH){sub 2}(CO{sub 3}){sub 2}{sup 2-}] and [Hf{sup 4+}+5CO{sub 3}{sup 2-}↔Hf(CO{sub 3}){sub 5}{sup 6-}], based on the SIT model, were determined to be 44.53±0.46 and 41.53±0.46, respectively, and based on the Pitzer model they were 44.56±0.48 and 40.20±0.48, respectively.

  6. The Hildebrand Solubility Parameters of Ionic Liquids—Part 2

    Science.gov (United States)

    Marciniak, Andrzej

    2011-01-01

    The Hildebrand solubility parameters have been calculated for eight ionic liquids. Retention data from the inverse gas chromatography measurements of the activity coefficients at infinite dilution were used for the calculation. From the solubility parameters, the enthalpies of vaporization of ionic liquids were estimated. Results are compared with solubility parameters estimated by different methods. PMID:21747694

  7. The Hildebrand solubility parameters of ionic liquids-part 2.

    Science.gov (United States)

    Marciniak, Andrzej

    2011-01-01

    The Hildebrand solubility parameters have been calculated for eight ionic liquids. Retention data from the inverse gas chromatography measurements of the activity coefficients at infinite dilution were used for the calculation. From the solubility parameters, the enthalpies of vaporization of ionic liquids were estimated. Results are compared with solubility parameters estimated by different methods.

  8. The Hildebrand Solubility Parameters of Ionic Liquids—Part 2

    Directory of Open Access Journals (Sweden)

    Andrzej Marciniak

    2011-06-01

    Full Text Available The Hildebrand solubility parameters have been calculated for eight ionic liquids. Retention data from the inverse gas chromatography measurements of the activity coefficients at infinite dilution were used for the calculation. From the solubility parameters, the enthalpies of vaporization of ionic liquids were estimated. Results are compared with solubility parameters estimated by different methods.

  9. Mid-Latitude Mobile Wideband HF- NVIS Channel Analysis: Part 1

    Science.gov (United States)

    2017-09-14

    commercial satellite communications (SATCOM) for beyond line-of-sight (LOS) links. However, standard HF systems operating over a 3-kHz bandwidth do not...citation of trade names and names of names of manufacturers is not to be construed as official government endorsement or approval of commercial ...Division EXECUTIVE SUMMARY High frequency (HF) links (2 to 30 MHz) are an alternative to the cost and tactical fragility of commercial satellite

  10. IUPAC-NIST Solubility Data Series. 95. Alkaline Earth Carbonates in Aqueous Systems. Part 2. Ca

    Science.gov (United States)

    Vanderdeelen, Jan

    2012-06-01

    The alkaline earth carbonates are an important class of minerals. This article is part of a volume in the IUPAC-NIST Solubility Data Series that compiles and critically evaluates solubility data of the alkaline earth carbonates in water and in simple aqueous electrolyte solutions. Part 1 outlined the procedure adopted in this volume, and presented the beryllium and magnesium carbonates. Part 2, the current paper, compiles and critically evaluates the solubility data of calcium carbonate. The chemical forms included are the anhydrous CaCO3 types calcite, aragonite, and vaterite, the monohydrate monohydrocalcite (CaCO3. H2O), the hexahydrate ikaite (CaCO3.6H2O), and an amorphous form. The data were analyzed with two model variants, and thermodynamic data of each form consistent with each of the models and with the CODATA key values for thermodynamics are presented.

  11. IUPAC-NIST Solubility Data Series. 95. Alkaline Earth Carbonates in Aqueous Systems. Part 2. Ca

    International Nuclear Information System (INIS)

    De Visscher, Alex; Vanderdeelen, Jan

    2012-01-01

    The alkaline earth carbonates are an important class of minerals. This article is part of a volume in the IUPAC-NIST Solubility Data Series that compiles and critically evaluates solubility data of the alkaline earth carbonates in water and in simple aqueous electrolyte solutions. Part 1 outlined the procedure adopted in this volume, and presented the beryllium and magnesium carbonates. Part 2, the current paper, compiles and critically evaluates the solubility data of calcium carbonate. The chemical forms included are the anhydrous CaCO 3 types calcite, aragonite, and vaterite, the monohydrate monohydrocalcite (CaCO 3 · H 2 O), the hexahydrate ikaite (CaCO 3 ·6H 2 O), and an amorphous form. The data were analyzed with two model variants, and thermodynamic data of each form consistent with each of the models and with the CODATA key values for thermodynamics are presented.

  12. IUPAC-NIST Solubility Data Series. 95. Alkaline Earth Carbonates in Aqueous Systems. Part 2. Ca

    Energy Technology Data Exchange (ETDEWEB)

    De Visscher, Alex; Vanderdeelen, Jan [Department of Chemical and Petroleum Engineering, and Centre for Environmental Engineering Research and Education (CEERE), Schulich School of Engineering, University of Calgary, Calgary, Alberta, T2N 1N4 (Canada); Department of Applied Analytical and Physical Chemistry, Faculty of Bioscience Engineering, Ghent University, B-9000 Ghent (Belgium)

    2012-06-15

    The alkaline earth carbonates are an important class of minerals. This article is part of a volume in the IUPAC-NIST Solubility Data Series that compiles and critically evaluates solubility data of the alkaline earth carbonates in water and in simple aqueous electrolyte solutions. Part 1 outlined the procedure adopted in this volume, and presented the beryllium and magnesium carbonates. Part 2, the current paper, compiles and critically evaluates the solubility data of calcium carbonate. The chemical forms included are the anhydrous CaCO{sub 3} types calcite, aragonite, and vaterite, the monohydrate monohydrocalcite (CaCO{sub 3}{center_dot} H{sub 2}O), the hexahydrate ikaite (CaCO{sub 3}{center_dot}6H{sub 2}O), and an amorphous form. The data were analyzed with two model variants, and thermodynamic data of each form consistent with each of the models and with the CODATA key values for thermodynamics are presented.

  13. HF laser

    International Nuclear Information System (INIS)

    Suzuki, Kazuya; Iwasaki, Matae

    1977-01-01

    A review is made of the research and development of HF chemical laser and its related work. Many gaseous compounds are used as laser media successfully; reaction kinetics and technological problems are described. The hybrid chemical laser of HF-CO 2 system and the topics related to the isotope separation are also included. (auth.)

  14. Radionuclide solubilities in boom clay. Final report, part 2 : a report produced for ONDRAF/NIRAS

    Energy Technology Data Exchange (ETDEWEB)

    Baker, S.; Baston, G.M.N.; Boult, K.A. [and others

    2000-07-01

    The release of radionuclides from a High Level Radioactive Waste repository situated in the Boom Clay at Mol would depend, in part, on their retardation within the Boom Clay. A number of parameters are required to assess such retardation; these include the solubilities of key radionuclides and their sorption behaviour. ONDRAF/NIRAS has identified neptunium, technetium, selenium, uranium and plutonium as elements for study. AEA Technology plc was requested to undertake a joint experimental and modelling study to determine the solubilities of these five elements under conditions representative of those in the Boom Clay (the in situ chemical conditions are pH{approx}8, Eh {approx} -230 mV). The work programme was carried out over three years, and for completeness this final report includes all the results.

  15. Radionuclide solubilities in boom clay. Final report, part 2 : a report produced for ONDRAF/NIRAS

    International Nuclear Information System (INIS)

    Baker, S.; Baston, G.M.N.; Boult, K.A.

    2000-01-01

    The release of radionuclides from a High Level Radioactive Waste repository situated in the Boom Clay at Mol would depend, in part, on their retardation within the Boom Clay. A number of parameters are required to assess such retardation; these include the solubilities of key radionuclides and their sorption behaviour. ONDRAF/NIRAS has identified neptunium, technetium, selenium, uranium and plutonium as elements for study. AEA Technology plc was requested to undertake a joint experimental and modelling study to determine the solubilities of these five elements under conditions representative of those in the Boom Clay (the in situ chemical conditions are pH∼8, Eh ∼ -230 mV). The work programme was carried out over three years, and for completeness this final report includes all the results

  16. Catalytic para-xylene maximization. Part X: Toluene disproportionation on HF promoted H-ZSM-5 catalysts

    Directory of Open Access Journals (Sweden)

    Ahmed K. Aboul-Gheit

    2012-12-01

    Full Text Available H-ZSM-5 zeolite catalysts were doped with 2%, 3% and 4%HF to be used for investigating their activities and selectivities for xylenes production and for para-xylene maximization at temperatures of 300–500 °C via toluene disproportionation. This doping caused pore size modification of the H-ZSM-5 catalyst. The reaction was carried out in a fixed bed flow type reactor. The ratio of produced para-xylene relative to its thermodynamic composition reached as high as 3.29 at 300 °C on the 4%HF doped H-ZSM-5 catalyst although this catalyst possessed the lowest amount of the largest pores (3.0–5.7 nm and the smallest pores (0.4–1.7 nm. The overall activities of the catalysts were decreased with an increase in HF doping because of diffusion restriction. The kinetics of the reaction were simply treated and found to give Ea and ΔS∗ values compatible with the characterization data of the catalysts.

  17. Mechanical alloying of Hf and Fe powders

    International Nuclear Information System (INIS)

    Mendoza Zelis, L.; Crespo, E.; Creus, M.; Damonte, L.C.; Sanchez, F.H.; Punte, G.

    1994-01-01

    Pure crystalline Hf and Fe powders were mixed and milled under an argon atmosphere. The evolution of the system with milling time was followed with Moessbauer effect spectroscopy and X-ray diffraction. The results indicate that in the first stages an amorphous Fe-rich alloy was gradually formed together with a solid solution of Hf in Fe beyond the solubility limit. (orig.)

  18. Solution properties of targacanthin (water-soluble part of gum tragacanth exudate from Astragalus gossypinus).

    Science.gov (United States)

    Mohammadifar, Mohammad Amin; Musavi, Seyed Mohammad; Kiumarsi, Amir; Williams, Peter A

    2006-02-28

    Solution properties of tragacanthin (the water-soluble part of gum tragacanth) were studied by gel permeation chromatography (GPC) combined with multi-angle light scattering and viscometry at 25 degrees C. Photon correlation spectroscopy was used to determine the hydrodynamic radius. Ultrasonic degradation was applied to obtain biopolymer fractions of different molecular weights. The dependence of intrinsic viscosity [eta] and radius of gyration (s2)z(1/2) on weight average molecular mass M(w) for this biopolymer were found to be [eta] = 9.077 x 10(-5) M(w)(0.87) (dL g(-1)) and (s2)z(1/2) in the range of M(w) from 1.8 x 10(5) to 1.6 x 10(6). The conformational parameters of tragacanthin were calculated to be 1111 nm for molar mass per unit contour length (M(L)), 26 nm for persistence length (q) and 1.87 ratio of R(g)/R(h). It was found that the Smidsrød parameter B, the empirical stiffness parameter was 0.013, which is lower than that of several polysaccharides indicating the stiff backbone for tragacanthin. The rheological behavior of aqueous solutions of gum tragacanth and its insoluble and soluble fractions (bassorin and tragacanthin, respectively) were studied. For concentrations equal to 1%, at 25 degrees C and in the absence of salt, bassorin solution showed the highest viscosity and shear thinning behaviour. Power law and Williamson models were used to describe the rheological behaviour of bassorin and tragacanthin, respectively. Oscillatory shear experiments showed a gel like structure for the bassorin but for tragacanthin the oscillatory data were as would be expected for semi-dilute to concentrated solution of entangled, random coil polymers. NaCl changed the steady and oscillatory rheological properties of both fractions and in this way the final viscosity of bassorin was even less than tragacanthin. The calculated activation energy for bassorin and tragacanthin indicated a more rapid decrease in viscosity with temperature for tragacanthin. The plot of

  19. Temperature Dependence of Mineral Solubility in Water. Part 2. Alkaline and Alkaline Earth Bromides

    Science.gov (United States)

    Krumgalz, B. S.

    2018-03-01

    Databases of alkaline and alkaline earth bromide solubilities in water at various temperatures were created using experimental data from publications over about the last two centuries. Statistical critical evaluation of the created databases was produced since there were enough independent data sources to justify such evaluation. The reliable experimental data were adequately described by polynomial expressions over various temperature ranges. Using the Pitzer approach for ionic activity and osmotic coefficients, the thermodynamic solubility products for the discussed bromide minerals have been calculated at various temperature intervals and also represented by polynomial expressions.

  20. Soluble Antioxidant Compounds Regenerate the Antioxidants Bound to Insoluble Parts of Foods

    NARCIS (Netherlands)

    Celik, E.E.; Gökmen, V.; Fogliano, V.

    2013-01-01

    This study aimed to investigate the regeneration potential of antioxidant capacity of an insoluble food matrix. Investigations were performed in vitro with several food matrices rich in dietary fiber (DF) and bound antioxidants. After removal of the soluble fraction, the antioxidant capacity (AC) of

  1. Amino acids as co-amorphous stabilizers for poorly water soluble drugs--Part 1

    DEFF Research Database (Denmark)

    Löbmann, Korbinian; Grohganz, Holger; Laitinen, Riikka

    2013-01-01

    molecular weight excipients that form specific molecular interactions with the drug resulting in co-amorphous forms. The two poorly water soluble drugs carbamazepine and indomethacin were combined with amino acids from the binding sites of the biological receptors of these drugs. Mixtures of drug...

  2. IUPAC-NIST Solubility Data Series. 100. Rare Earth Metal Fluorides in Water and Aqueous Systems. Part 3. Heavy Lanthanides (Gd–Lu)

    Energy Technology Data Exchange (ETDEWEB)

    Mioduski, Tomasz [Institute of Nuclear Chemistry and Technology, 03195 Warszawa (Poland); Gumiński, Cezary, E-mail: cegie@chem.uw.edu.pl [Department of Chemistry, University of Warsaw, 02093 Warszawa (Poland); Zeng, Dewen, E-mail: dewen-zeng@hotmail.com [College of Chemistry and Chemical Engineering, Central South University, Changsha 410083 (China)

    2015-06-15

    This is the third part of the volume devoted to solubility data for the rare earth metal (REM) fluorides in water and in aqueous ternary and multicomponent systems. It covers experimental results of trivalent fluorides of Gd, Tb, Dy, Ho, Er, Tm, Yb, and Lu (so-called heavy lanthanides), since no quantitative data on solubilities of TbF{sub 4} and YbF{sub 2} (the most stable compounds at these valencies) are available. The related literature has been covered through the end of 2014. Compilations of all available papers with the solubility data are introduced for each REM fluoride with a corresponding critical evaluation. Every such assessment contains a collection of all solubility results in aqueous solution, a selection of suggested solubility data, a solubility equation, and a brief discussion of the multicomponent systems. Only simple fluorides (no complexes or double salts) are treated as the input substances in this report. General features of the systems, such as nature of the equilibrium solid phases, solubility as a function of temperature, influence of ionic strength, solution pH, mixed solvent medium on the solubility, quality of the solubility results, and the solubility as a function of REM atomic number, have already been presented in Part 1 of the volume.

  3. Soluble antioxidant compounds regenerate the antioxidants bound to insoluble parts of foods.

    Science.gov (United States)

    Çelik, Ecem Evrim; Gökmen, Vural; Fogliano, Vincenzo

    2013-10-30

    This study aimed to investigate the regeneration potential of antioxidant capacity of an insoluble food matrix. Investigations were performed in vitro with several food matrices rich in dietary fiber (DF) and bound antioxidants. After removal of the soluble fraction, the antioxidant capacity (AC) of the insoluble fraction was measured by the QUENCHER procedure using ABTS(•+) or DPPH(•) radicals. After measurement, the insoluble residue was washed out to remove the excess of radicals and treated with pure antioxidant solution or antioxidant-rich beverage to regenerate depleted antioxidants on the fiber. Results revealed that the antioxidant capacity of compounds chemically bound to the insoluble moiety could be reconstituted in the presence of other hydrogen-donating substances in the liquid phase. Regeneration efficiency was found to range between 21.5 and 154.3% depending on the type of insoluble food matrix and regeneration agent. Among the food matrices studied, cereal products were found to have slightly higher regeneration efficiency, whereas antioxidant-rich beverages were more effective than pure antioxidants as regeneration agents. Taking wheat bran as reference insoluble material, the regeneration abilities of beverages were in the following order: green tea > espresso coffee > black tea > instant coffee > orange juice > red wine. These results highlighted the possible physiological relevance of antioxidants bound to the insoluble food material in the gastrointestinal tract. During the digestion process they could react with the free radicals and at the same time they can be regenerated by other soluble antioxidant compounds present in the meal.

  4. HF i dag

    DEFF Research Database (Denmark)

    Lindstrøm, Maria Duclos; Simonsen, Birgitte

    2008-01-01

    Notatet er lavet på baggrund af uddannelsesbiografiske dybdeinterviews med kursister på toårigt HF. Indenfor rammerne af en pilotundersøgelse identificerer notatet fire gennemgående profiler: De pragmatiske, de fagligt usikre, second chance-kursisterne, og de HF-kursister, som har HF som first...

  5. A novel tantalum-containing bioglass. Part I. Structure and solubility

    Energy Technology Data Exchange (ETDEWEB)

    Alhalawani, Adel MF. [Department of Mechanical & Industrial Engineering, Ryerson University, Toronto, Ontario (Canada); Towler, Mark R., E-mail: mtowler@ryerson.ca [Department of Mechanical & Industrial Engineering, Ryerson University, Toronto, Ontario (Canada); Li Ka Shing Knowledge Institute, St. Michael' s Hospital, Toronto, Ontario (Canada)

    2017-03-01

    Bioglasses are employed for surgical augmentation in a range of hard tissue applications. Tantalum is a bioactive and biocompatible transition metal that has been used as an orthopedic medical device. It has a range of biological and physical properties that make its incorporation into ionic form into bioactive glass systems promising for various clinical applications. The work herein reports the characterization and properties of novel tantalum-containing glasses. A series of glasses based on the system 48SiO{sub 2}-(36-X)ZnO-6CaO-8SrO-2P{sub 2}O{sub 5}-XTa{sub 2}O{sub 5} with X varying from 0 mol% (TA0) to 0.5 mol% (TA2) were synthesized. The addition of small amounts of Ta{sub 2}O{sub 5} did not cause crystallization of the glasses but increasing Ta{sub 2}O{sub 5} content at the expense of ZnO was found to result in an increased number of bridging oxygens (BOs). This, along with the data recorded by differential thermal analysis (DTA) and magic angle spinning-nuclear magnetic resonance (MAS-NMR), confirms that Ta acts as a glass former in this series. Solubility experiments showed that minor changes in the glass structure caused by Ta incorporation (0.5 mol%) exhibited greater cumulative % weight loss, pH values and cumulative Zn{sup 2+} and Sr{sup 2+} ion concentration over a period of 30 days of maturation, when compared to Ta{sub 2}O{sub 5}-free glasses. The results presented in this article confirm that replacing ZnO with Ta{sub 2}O{sub 5} in silicate glasses results in the formation of stronger bonds within the glass network without any adverse effects on the solubility of the glasses prepared from them. - Highlights: • Ta{sub 2}O{sub 5} can be incorporated into silicate based ionomer glasses up to 0.5 mol%. • Incorporation resulted in amorphous glasses. • Insertion of TaO units into the silicate network confirms the former role of Ta{sub 2}O{sub 5}. • The incorporation increased the glass solubility.

  6. Highly Luminescent, Water-Soluble Lanthanide Fluorobenzoates: Syntheses, Structures and Photophysics, Part I: Lanthanide Pentafluorobenzoates.

    Science.gov (United States)

    Kalyakina, Alena S; Utochnikova, Valentina V; Bushmarinov, Ivan S; Ananyev, Ivan V; Eremenko, Igor L; Volz, Daniel; Rönicke, Franziska; Schepers, Ute; Van Deun, Rik; Trigub, Alexander L; Zubavichus, Yan V; Kuzmina, Natalia P; Bräse, Stefan

    2015-12-01

    Highly luminescent, photostable, and soluble lanthanide pentafluorobenzoates have been synthesized and thoroughly characterized, with a focus on Eu(III) and Tb(III) complexes as visible emitters and Nd(III) , Er(III) , and Yb(III) complexes as infrared emitters. Investigation of the crystal structures of the complexes in powder form and as single crystals by using X-ray diffraction revealed five different structural types, including monomeric, dimeric, and polymeric. The local structure in different solutions was studied by using X-ray absorption spectroscopy. The photoluminescence quantum yields (PLQYs) of terbium and europium complexes were 39 and 15 %, respectively; the latter value was increased almost twice by using the heterometallic complex [Tb0.5 Eu0.5 (pfb)3 (H2 O)] (Hpfb=pentafluorobenzoic acid). Due to the effectively utilized sensitization strategy (pfb)(-) →Tb→Eu, a pure europium luminescence with a PLQY of 29 % was achieved. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  7. Mapping ionospheric backscatter measured by the SuperDARN HF radars – Part 2: Assessing SuperDARN virtual height models

    Directory of Open Access Journals (Sweden)

    T. K. Yeoman

    2008-05-01

    Full Text Available The Super Dual Auroral Radar Network (SuperDARN network of HF coherent backscatter radars form a unique global diagnostic of large-scale ionospheric and magnetospheric dynamics in the Northern and Southern Hemispheres. Currently the ground projections of the HF radar returns are routinely determined by a simple rangefinding algorithm, which takes no account of the prevailing, or indeed the average, HF propagation conditions. This is in spite of the fact that both direct E- and F-region backscatter and 1½-hop E- and F-region backscatter are commonly used in geophysical interpretation of the data. In a companion paper, Chisham et al. (2008 have suggested a new virtual height model for SuperDARN, based on average measured propagation paths. Over shorter propagation paths the existing rangefinding algorithm is adequate, but mapping errors become significant for longer paths where the roundness of the Earth becomes important, and a correct assumption of virtual height becomes more difficult. The SuperDARN radar at Hankasalmi has a propagation path to high power HF ionospheric modification facilities at both Tromsø on a ½-hop path and SPEAR on a 1½-hop path. The SuperDARN radar at Þykkvibǽr has propagation paths to both facilities over 1½-hop paths. These paths provide an opportunity to quantitatively test the available SuperDARN virtual height models. It is also possible to use HF radar backscatter which has been artificially induced by the ionospheric heaters as an accurate calibration point for the Hankasalmi elevation angle of arrival data, providing a range correction algorithm for the SuperDARN radars which directly uses elevation angle. These developments enable the accurate mappings of the SuperDARN electric field measurements which are required for the growing number of multi-instrument studies of the Earth's ionosphere and magnetosphere.

  8. Defensive strategies in Geranium sylvaticum, Part 2: Roles of water-soluble tannins, flavonoids and phenolic acids against natural enemies.

    Science.gov (United States)

    Tuominen, Anu

    2013-11-01

    Geranium sylvaticum is a common herbaceous plant in Fennoscandia, which has a unique phenolic composition. Ellagitannins, proanthocyanidins, galloylglucoses, gallotannins, galloyl quinic acids and flavonoids possess variable distribution in its different organs. These phenolic compounds are thought to have an important role in plant-herbivore interactions. The aim of this study was to quantify these different water-soluble phenolic compounds and measure the biological activity of the eight organs of G. sylvaticum. Compounds were characterized and quantified using HPLC-DAD/MS, in addition, total proanthocyanidins were determined by BuOH-HCl assay and total phenolics by the Folin-Ciocalteau method. Two in vitro biological activity measurements were used: the prooxidant activity was measured by the browning assay and antioxidant activity by the 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging assay. Organ extracts were fractionated using column chromatography on Sephadex LH-20 and the activities of fractions was similarly measured to evaluate which polyphenol groups contributed the most to the biological activity of each organ. The data on the activity of fractions were examined by multivariate data analysis. The water-soluble extracts of leaves and pistils, which contained over 30% of the dry weight as ellagitannins, showed the highest pro-oxidant activity among the organ extracts. Fraction analysis revealed that flavonoids and galloyl quinic acids also exhibited high pro-oxidant activity. In contrast, the most antioxidant active organ extracts were those of the main roots and hairy roots that contained high amounts of proanthocyanidins in addition to ellagitannins. Analysis of the fractions showed that especially ellagitannins and galloyl quinic acids have high antioxidant activity. We conclude that G. sylvaticum allocates a significant amount of tannins in those plant parts that are important to the fitness of the plant and susceptible to natural enemies, i

  9. A single parameter representation of hygroscopic growth and cloud condensation nucleus activity – Part 2: Including solubility

    Directory of Open Access Journals (Sweden)

    M. D. Petters

    2008-10-01

    Full Text Available The ability of a particle to serve as a cloud condensation nucleus in the atmosphere is determined by its size, hygroscopicity and its solubility in water. Usually size and hygroscopicity alone are sufficient to predict CCN activity. Single parameter representations for hygroscopicity have been shown to successfully model complex, multicomponent particles types. Under the assumption of either complete solubility, or complete insolubility of a component, it is not necessary to explicitly include that component's solubility into the single parameter framework. This is not the case if sparingly soluble materials are present. In this work we explicitly account for solubility by modifying the single parameter equations. We demonstrate that sensitivity to the actual value of solubility emerges only in the regime of 2×10−1–5×10−4, where the solubility values are expressed as volume of solute per unit volume of water present in a saturated solution. Compounds that do not fall inside this sparingly soluble envelope can be adequately modeled assuming they are either infinitely soluble in water or completely insoluble.

  10. HF-laser program

    International Nuclear Information System (INIS)

    Anon.

    1978-01-01

    Sandia's HF-laser program for FY 77 and FY 78 was revised in June 1977 in order to meet several new program milestones. Research progress is reported on: objective of HF oscillator-amplifier studies using H 2 -F 2 gas mixtures; characteristics of large-volume oscillator using H 2 -F 2 mixtures; characteristics of large-volume amplifier using H 2 -F 2 mixtures; experimental results of the oscillator-amplifier study; objective of high-quality discharge-initiated SF 6 -HI oscillator-preamplifier system; pin-discharge-initiated oscillator and first beam expander; fast-discharge-initiated preamplifiers; reflecting beam expanders for oscillator-preamplifier system; beam quality of discharge-initiated oscillator-preamplifier system; short pulse option for discharge initiated SF 6 -HI system; H 2 -F 2 electron-beam-initiated oscillator-preamplifier system; chamber for HF-laser focusing experiments; computer study of parasitic oscillations in HF amplifiers and oscillators; kinetics upgrade of HF-laser code; repetitivey ignited flowing H 2 -F 2 -O 2 mixtures; spontaneous detonations in multiatmosphere H 2 -F 2 -O 2 mixtures; high-pressure H 2 -F 2 laser studies; and time sequenced energy extraction on the high xenon laser

  11. Plume-related mantle source of super-large rare metal deposits from the Lovozero and Khibina massifs on the Kola Peninsula, Eastern part of Baltic Shield: Sr, Nd and Hf isotope systematics

    Science.gov (United States)

    Kogarko, L. N.; Lahaye, Y.; Brey, G. P.

    2010-03-01

    The two world’s largest complexes of highly alkaline nepheline syenites and related rare metal loparite and eudialyte deposits, the Khibina and Lovozero massifs, occur in the central part of the Kola Peninsula. We measured for the first time in situ the trace element concentrations and the Sr, Nd and Hf isotope ratios by LA-ICP-MS (laser ablation inductively coupled plasma mass spectrometer) in loparite, eudialyte an in some other pegmatitic minerals. The results are in aggreement with the whole rock Sr and Nd isotope which suggests the formation of these superlarge rare metal deposits in a magmatic closed system. The initial Hf, Sr, Nd isotope ratios are similar to the isotopic signatures of OIB indicating depleted mantle as a source. This leads to the suggestion that the origin of these gigantic alkaline intrusions is connected to a deep seated mantle source—possibly to a lower mantle plume. The required combination of a depleted mantle and high rare metal enrichment in the source can be explained by the input of incompatible elements by metasomatising melts/fluids into the zones of alkaline magma generation shortly before the partial melting event (to avoid ingrowth of radiogenic isotopes). The minerals belovite and pyrochlore from the pegmatites are abnormally high in 87Sr /86Sr ratios. This may be explained by closed system isotope evolution as a result of a significant increase in Rb/Sr during the evolution of the peralkaline magma.

  12. HF/DF chemical labs

    International Nuclear Information System (INIS)

    Meinzer, R.A.

    1987-01-01

    This paper provides the essential details to understand and design HF/DF and related types of chemical lasers. The basic operation of the HF/DF chemical laser is described. The details of the excitation chemistry are presented and the pertinent laser physics is described. A description of the various laser components is given and the analytical models for the HF/DF chemical laser are discussed. A brief description of the chain reaction HF/DF chemical laser is offered

  13. Consideration on thermodynamic data for predicting solubility and chemical species of elements in groundwater. Part 1: Tc, U, Am

    Energy Technology Data Exchange (ETDEWEB)

    Yamaguchi, Tetsuji; Takeda, Seiji [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1999-01-01

    The solubility determines the release of radionuclides from waste form and is used as a source term in radionuclide migration analysis in performance assessment of radioactive waste repository. Complexations of radionuclides by ligands in groundwater affect the interaction between radionuclides and geologic media, thus affect their migration behavior. Thermodynamic data for Tc, Am and U were reviewed and compiled to be used for predicting the solubility and chemical species in groundwater. Thermodynamic data were reviewed with emphasis on the hydrolysis and carbonate complexation that can dominate the speciation in typical groundwater. Thermodynamic data for other species were selected based on existing database. Thermodynamic data for other important elements are under investigation, thus shown in an appendix for temporary use. (author)

  14. Consideration on thermodynamic data for predicting solubility and chemical species of elements in groundwater. Part 2: Np, Pu

    International Nuclear Information System (INIS)

    Yamaguchi, Tetsuji

    2000-11-01

    The solubility determines the release of a radionuclide from waste form and is used as a source term in radionuclide migration analysis in performance assessment of radioactive waste repository. Complexations of the radionuclide by ligands in groundwater affect the interaction between radionuclides and geologic media, thus affect their migration behavior. It is essential to estimate the solubility and to predict the chemical species for the radionuclide based on thermodynamic data. The thermodynamic data of aqueous species and compounds were reviewed and compiled for Np and Pu. Thermodynamic data were reviewed with emphasis on the hydrolysis and carbonate complexation that can dominate the speciation in groundwater. Thermodynamic data for other species were selected based on existing databases. Thermodynamic data for other important elements are under investigation, thus shown in an appendix for temporary use. (author)

  15. Corrosion and solubility in a TSP-buffered chemical environment following a loss of coolant accident: Part 1 – Aluminum

    Energy Technology Data Exchange (ETDEWEB)

    Howe, Kerry J., E-mail: howe@unm.edu [University of New Mexico, 210 University Blvd., Albuquerque, NM 87131 (United States); Mitchell, Lana, E-mail: lmitchell@alionscience.com [University of New Mexico, 210 University Blvd., Albuquerque, NM 87131 (United States); Kim, Seung-Jun, E-mail: skim@lanl.gov [University of New Mexico, 210 University Blvd., Albuquerque, NM 87131 (United States); Blandford, Edward D., E-mail: edb@unm.edu [University of New Mexico, 210 University Blvd., Albuquerque, NM 87131 (United States); Kee, Ernest J., E-mail: erniekee@gmail.com [South Texas Project Nuclear Operating Company, P.O. Box 270, Wadsworth, TX 77483 (United States)

    2015-10-15

    Highlights: • Trisodium phosphate (TSP) causes aluminum corrosion to cease after 24 h of exposure. • Chloride, iron, and copper have a minimal effect on the rate of aluminum corrosion when TSP is present. • Zinc can reduce the rate of aluminum corrosion when TSP is present. • Aluminum occasionally precipitates at concentrations lower than the calculated solubility for Al(OH){sub 3}. • Corrosion and solubility equations can be used to calculate the solids generated during a LOCA. - Abstract: Bench experiments were conducted to investigate the effect of the presence of trisodium phosphate (TSP) on the corrosion and release of aluminum from metallic aluminum surfaces under conditions representative of the containment pool following a postulated loss of coolant accident at a nuclear power generating facility. The experiments showed that TSP is capable of passivating the aluminum surface and preventing continued corrosion after about 24 h at the conditions tested. A correlation that describes the rate of corrosion including the passivation effect was developed from the bench experiments and validated with a separate set of experiments from a different test system. The saturation concentration of aluminum was shown to be well described by the solubility of amorphous aluminum hydroxide for the majority of cases, but instances have been observed when aluminum precipitates at concentrations lower than the calculated aluminum hydroxide solubility. Based on the experimental data and previous literature, an equation was developed to calculate the saturation concentration of aluminum as a function of pH and temperature under conditions representative of a loss of coolant accident (LOCA) in a TSP-buffered pressurized water reactor (PWR) containment. The corrosion equation and precipitation equation can be used in concert with each other to calculate the quantity of solids that would form as a function of time during a LOCA if the temperature and pH profiles were known.

  16. Corrosion and solubility in a TSP-buffered chemical environment following a loss of coolant accident: Part 1 – Aluminum

    International Nuclear Information System (INIS)

    Howe, Kerry J.; Mitchell, Lana; Kim, Seung-Jun; Blandford, Edward D.; Kee, Ernest J.

    2015-01-01

    Highlights: • Trisodium phosphate (TSP) causes aluminum corrosion to cease after 24 h of exposure. • Chloride, iron, and copper have a minimal effect on the rate of aluminum corrosion when TSP is present. • Zinc can reduce the rate of aluminum corrosion when TSP is present. • Aluminum occasionally precipitates at concentrations lower than the calculated solubility for Al(OH) 3 . • Corrosion and solubility equations can be used to calculate the solids generated during a LOCA. - Abstract: Bench experiments were conducted to investigate the effect of the presence of trisodium phosphate (TSP) on the corrosion and release of aluminum from metallic aluminum surfaces under conditions representative of the containment pool following a postulated loss of coolant accident at a nuclear power generating facility. The experiments showed that TSP is capable of passivating the aluminum surface and preventing continued corrosion after about 24 h at the conditions tested. A correlation that describes the rate of corrosion including the passivation effect was developed from the bench experiments and validated with a separate set of experiments from a different test system. The saturation concentration of aluminum was shown to be well described by the solubility of amorphous aluminum hydroxide for the majority of cases, but instances have been observed when aluminum precipitates at concentrations lower than the calculated aluminum hydroxide solubility. Based on the experimental data and previous literature, an equation was developed to calculate the saturation concentration of aluminum as a function of pH and temperature under conditions representative of a loss of coolant accident (LOCA) in a TSP-buffered pressurized water reactor (PWR) containment. The corrosion equation and precipitation equation can be used in concert with each other to calculate the quantity of solids that would form as a function of time during a LOCA if the temperature and pH profiles were known

  17. Solid dispersions, part II: new strategies in manufacturing methods for dissolution rate enhancement of poorly water-soluble drugs.

    Science.gov (United States)

    Bikiaris, Dimitrios N

    2011-12-01

    The absorption of poorly water-soluble drugs, when presented in the crystalline state to the gastrointestinal tract, is typically dissolution rate-limited, and according to BCS these drugs belong mainly to class II. Both dissolution kinetics and solubility are particle size dependent. Nowadays, various techniques are available to the pharmaceutical industry for dissolution rate enhancement of such drugs. Among such techniques, nanosuspensions and drug formulation in solid dispersions are those with the highest interest. This review discusses strategies undertaken over the last 10 years, which have been applied for the dissolution enhancement of poorly water-soluble drugs; such processes include melt mixing, electrospinning, microwave irradiation and the use of inorganic nanoparticles. Many problems in this field still need to be solved, mainly the use of toxic solvents, and for this reason the use of innovative new procedures and materials will increase over the coming years. Melt mixing remains extremely promising for the preparation of SDs and will probably become the most used method in the future for the preparation of solid drug dispersions.

  18. Corrosion and solubility in a TSP-buffered chemical environment following a loss of coolant accident: Part 2 – Zinc

    International Nuclear Information System (INIS)

    Pease, David; LaBrier, Daniel; Ali, Amir; Blandford, Edward D.; Howe, Kerry J.

    2016-01-01

    Highlights: • Zinc release is limited to less than 1 mg/L in TSP-buffered solution under a variety of conditions (pH, temperature, zinc source). • Zinc release in high-temperature non-TSP-buffered environment is approximately 25 mg/L. • Long-term zinc release is controlled by passivation (without TSP) and zinc solubility (with TSP). • Precipitation and solubility of zinc phosphate limit the release of zinc. - Abstract: Bench experiments were conducted to investigate the effect of the presence of trisodium phosphate (TSP) on the corrosion and release of zinc from metallic zinc-bearing surfaces under conditions representative of the containment pool following a postulated loss of coolant accident (LOCA) at a nuclear power generating facility. The experiments showed that in non-buffered (acidic) environments, measurable quantities of zinc are released from zinc-bearing surfaces. Precipitation and solubility of phosphate-based corrosion products, such as zinc phosphate, limit the release of zinc from zinc-bearing surfaces. These experiments have found that under a variety of conditions, including variations of temperature, pH, and across different zinc-bearing surfaces, the release of zinc into solution is limited to <1 mg/L when phosphate is present. When phosphate is not present, zinc release is instead bounded by a markedly higher saturation limit which is a strong function of the solution temperature.

  19. Physical characteristics and solubility of long-lived airborne particulates in uranium producing and manufacturing facilities Phase IV - Part III

    International Nuclear Information System (INIS)

    Robertson, R.; Stuart, D.C.

    1995-08-01

    The rates of dissolution in simulated lung fluid of uranium, thorium-230, radium-226 and lead-210 from six aerosol samples associated with mining operations at Cluff Lake, Saskatchewan were determined. Parallel studies were carried out for uranium aerosol samples collected directly on open-face filters at the Port Hope refinery and from four aerosol samples generated in the laboratory from yellowcake dusts obtained from the Blind River mill in Ontario. Bulk dusts were collected from surfaces in workplace locations. These dusts were resuspended in the laboratory and collected on glass fibre substrates using cascade impactor sampling methods. Two particle size fractions, less than 7 microns and 7-10 microns were collected. In all, 18 samples were subjected to parallel extractions by simulated lung fluid under continuous flow, at 37 deg C at pH 7.4, over a period of 66 days. For each extraction, 10 lung fluid fractions were collected at predetermined intervals and analyzed for uranium to estimate uranium dissolution rates as a function of time. For the Cluff Lake ore dust samples, analyses and dissolution rates estimates for thorium-230, radium-226 and lead-210 were also performed. The samples taken from Cluff Lake were found to be relatively insoluble. Uranium dissolution rates of about 20% were measured over 66 days. No measurable Th-228 dissolution was found during the experiments. Ra-226 and Pb-210 were most soluble as a fine particulate (less than 7 μm), with complete dissolution for some samples. Aerosol samples from Blind River and Port Hope were more readily soluble (complete dissolution over 66 days). The Blind River aerosols dissolved more slowly than the Port Hope aerosols. In both cases, the majority of the dissolution occurred within the first week. There was no effect of particle size on dissolution rate. (author). 12 refs., 6 tabs., 1 fig

  20. HF-laser program

    International Nuclear Information System (INIS)

    Anon.

    1978-01-01

    The HF laser is an attractive candidate driver for a large-system ICF scientific demonstration facility, for an ICF experimental power reactor and for a commercial laser--fusion power reactor. Previous accomplishments of the program have included demonstrations of high efficiency and high energy capability, efficient energy extraction from HF amplifiers, good beam quality and focusability, and short-pulse generation and amplification. In the reporting period, beam quality has been determined to be near-diffraction limited for a short pulsewidth (6 ns to 25 ns) oscillator-amplifier chain, suppression of amplified spontaneous emission has been demonstrated on an individual spectral line, high-pressure characteristics have been determined for the Phoenix I amplifier, and detailed comparisions between the kinetic code and experiments have been made. Details of two major upcoming experiments are also included. The first is energy extraction and beam quality measurements on the Phoenix I amplifier operating under saturated output power conditions. The second experiment, using a newly designed amplifier (Phoenix II), is designed to demonstrate the concept of angular-multiplexing: a pulse width-compression scheme

  1. Pulsed inductive HF laser

    Energy Technology Data Exchange (ETDEWEB)

    Razhev, A M; Kargapol' tsev, E S [Institute of Laser Physics, Siberian Branch, Russian Academy of Sciences, Novosibirsk (Russian Federation); Churkin, D S; Demchuk, S V [Novosibirsk State University, Novosibirsk (Russian Federation)

    2016-03-31

    We report the results of experimentally investigated dependences of temporal, spectral and spatial characteristics of an inductive HF-laser generation on the pump conditions. Gas mixtures H{sub 2} – F{sub 2}(NF{sub 3} or SF6{sub 6}) and He(Ne) – H{sub 2} – F{sub 2}(NF{sub 3} or SF{sub 6}) were used as active media. The FWHM pulse duration reached 0.42 μs. This value corresponded to a pulsed power of 45 kW. For the first time, the emission spectrum of an inductive HF laser was investigated, which consisted of seven groups of bands with centres around the wavelengths of 2732, 2736, 2739, 2835, 2837, 2893 and 2913 nm. The cross section profile of the laser beam was a ring with a diameter of about 20 mm and width of about 5 mm. Parameters of laser operation in the repetitively pulsed regime were sufficiently stable. The amplitude instability of light pulses was no greater than 5% – 6%. (lasers)

  2. HF-DLLME

    OpenAIRE

    Simão, Vanessa

    2015-01-01

    Tese (doutorado) - Universidade Federal de Santa Catarina, Centro de Ciências Físicas e Matemáticas, Programa de Pós-Graduação em Química, Florianópolis, 2015. Neste trabalho foi proposto, pela primeira vez, a combinação simultânea das técnicas de microextração em fase líquida suportada em fibra oca (HF-LPME) e microextração líquido-líquido dispersiva (DLLME) para aplicação em amostras líquidas. Dois estudos foram desenvolvidos utilizando a metodologia proposta, a qua...

  3. High energy HF pulsed lasers

    International Nuclear Information System (INIS)

    Patterson, E.L.; Gerber, R.A.

    1976-01-01

    Recent experiments show that pulsed HF lasers are capable of producing high energy with good efficiency. Preliminary experiments show that the laser radiation from the high-gain medium can be controlled with a low-power probe laser beam or with low-level feedback. These results indicate that the HF laser may have potential for second-generation laser fusion experiments

  4. Physical characteristics and solubility of long-lived airborne particulates in uranium producing and manufacturing facilities. Phase III - Part II

    International Nuclear Information System (INIS)

    Robertson, R.; Stuart, D.C.; Stothers, M.A.

    1995-08-01

    The rates of dissolution in simulated lung fluid of uranium from aerosols associated with various stages of the yellowcake manufacturing process have been studied. Dusts were collected from eight workplace locations. Each dust sample was resuspended in the laboratory and collected on glass fibre substrates using cascade impactor sampling methods. The two particle size fractions collected were less than 7 microns and 10-7 microns. Each sample was prepared in duplicate. In all, 32 aerosol samples were prepared for solubility extraction studies. The aerosol-bearing filters were subjected to parallel extractions by simulated lung fluid under continuous flow, at 37 deg C at pH 7.4, over a period of 68.5 days. Ten lung fluid fractions were collected at predetermined time intervals and analyzed to allow estimates of uranium dissolution rates as a function of time. After completion of the 68.5 day simulated lung fluid extraction, the residual samples were subjected to a more aggressive nitric acid extraction for 48 hours. The fraction of uranium dissolved over the first 12 hours varied from 27% to 98% for seven of the eight yellowcake samples. For these yellowcake samples, the fractions of uranium dissolved over the first 36 hours and over the full 68.5 days ranged from 49% to 99% and 80% to 100% respectively. The eighth sample was a calcined yellowcake. The rate of dissolution for the calcined yellowcake was less than 4.5% over the first 12 hours and less than 10% over 68.5 days. No influence of particle size on the rate of dissolution was found. Most of the uranium was dissolved by the simulated lung fluid for seven of the eight yellowcake samples. As a result, the nitric acid extraction of the residual samples had little effect on these seven samples. The nitric acid extraction of the calcined sample, which was found to be relatively insoluble in simulated lung fluid, dissolved a further 21% to 36.1% of the uranium. (author). 9 refs., 6 tabs., 1 fig

  5. GC-MS characterization of n-hexane soluble fraction from dandelion (Taraxacum officinale Weber ex F.H. Wigg.) aerial parts and its antioxidant and antimicrobial properties.

    Science.gov (United States)

    Ivanov, Ivan; Petkova, Nadezhda; Tumbarski, Julian; Dincheva, Ivayla; Badjakov, Ilian; Denev, Panteley; Pavlov, Atanas

    2018-01-26

    A comparative investigation of n-hexane soluble compounds from aerial parts of dandelion (Taraxacum officinale Weber ex F.H. Wigg.) collected during different vegetative stages was carried out. The GC-MS analysis of the n-hexane (unpolar) fraction showed the presence of 30 biologically active compounds. Phytol [14.7% of total ion current (TIC)], lupeol (14.5% of TIC), taraxasteryl acetate (11.4% of TIC), β-sitosterol (10.3% of TIC), α-amyrin (9.0% of TIC), β-amyrin (8.3% of TIC), and cycloartenol acetate (5.8% of TIC) were identified as the major components in n-hexane fraction. The unpolar fraction exhibited promising antioxidant activity - 46.7 mmol Trolox equivalents/g extract (determined by 1,1-diphenyl-2-picrylhydrazyl method). This fraction demonstrated insignificant antimicrobial activity and can be used in cosmetic and pharmaceutical industries.

  6. Plutonium solubilities

    International Nuclear Information System (INIS)

    Puigdomnech, I.; Bruno, J.

    1991-02-01

    Thermochemical data has been selected for plutonium oxide, hydroxide, carbonate and phosphate equilibria. Equilibrium constants have been evaluated in the temperature range 0 to 300 degrees C at a pressure of 1 bar to T≤100 degrees C and at the steam saturated pressure at higher temperatures. Measured solubilities of plutonium that are reported in the literature for laboratory experiments have been collected. Solubility data on oxides, hydroxides, carbonates and phosphates have been selected. No solubility data were found at temperatures higher than 60 degrees C. The literature solubility data have been compared with plutonium solubilities calculated with the EQ3/6 geochemical modelling programs, using the selected thermodynamic data for plutonium. (authors)

  7. Hf på VUC

    DEFF Research Database (Denmark)

    Pless, Mette; Hansen, Niels-Henrik Møller

    . Konkret har forskningsprojektet 3 mål: At afdække hf-kursisternes tidligere uddannelsesforløb og -erfaringer, før de starter på hf på VUC.At afdække, hvordan mødet med uddannelsens studiemiljø opleves af kursisterne, og ikke mindst kursisternes oplevelse af undervisningsformer, lærere mm.At afdække, hvad...

  8. The dynamics of acid-soluble phosphorus compounds in the course of winter and spring wheat germination under various thermic conditions. Part II. Labile phosphorus after hydrolysis of the acid-soluble fraction

    Directory of Open Access Journals (Sweden)

    A. Barbaro

    2015-06-01

    Full Text Available The changes in labile phosphorus compounds content during germination of wheat were investigated. These compounds were determined in acid-soluble germ extracts separated into fractions according to the solubility of their barium salts. Low germination temperature was found to raise the labile phosphorus content in the fraction of insoluble barium salts. If we assume that labile P of this fraction consisted mainly of adenosinedi- and triphosphates, it would seem that the rise, in the ATP and ADP level under the influence of low temperature may be essential for initiating flowering in winter varieties.

  9. EQ3NR, a computer program for geochemical aqueous speciation-solubility calculations: Theoretical manual, user`s guide, and related documentation (Version 7.0); Part 3

    Energy Technology Data Exchange (ETDEWEB)

    Wolery, T.J.

    1992-09-14

    EQ3NR is an aqueous solution speciation-solubility modeling code. It is part of the EQ3/6 software package for geochemical modeling. It computes the thermodynamic state of an aqueous solution by determining the distribution of chemical species, including simple ions, ion pairs, and complexes, using standard state thermodynamic data and various equations which describe the thermodynamic activity coefficients of these species. The input to the code describes the aqueous solution in terms of analytical data, including total (analytical) concentrations of dissolved components and such other parameters as the pH, pHCl, Eh, pe, and oxygen fugacity. The input may also include a desired electrical balancing adjustment and various constraints which impose equilibrium with special pure minerals, solid solution end-member components (of specified mole fractions), and gases (of specified fugacities). The code evaluates the degree of disequilibrium in terms of the saturation index (SI = 1og Q/K) and the thermodynamic affinity (A = {minus}2.303 RT log Q/K) for various reactions, such as mineral dissolution or oxidation-reduction in the aqueous solution itself. Individual values of Eh, pe, oxygen fugacity, and Ah (redox affinity) are computed for aqueous redox couples. Equilibrium fugacities are computed for gas species. The code is highly flexible in dealing with various parameters as either model inputs or outputs. The user can specify modification or substitution of equilibrium constants at run time by using options on the input file.

  10. HF Interference, Procedures and Tools (Interferences HF, procedures et outils)

    Science.gov (United States)

    2007-06-01

    the actual ambient noise floor situation. Besides these HF radio links, special units such as crisis reaction forces are using low power radios for...the origin point on the ground. For ease of arithmetic and typography , the latter option is preferable. The dipole-modelled PLT is located at x = H1

  11. Zirconium Zr and hafnium Hf

    International Nuclear Information System (INIS)

    Busev, A.I.; Tiptsova, V.G.; Ivanov, V.M.

    1978-01-01

    The basic methods for extracting and determining Zr(4) and Hf(4) are described. Diantipyrinemethane and its alkyl homologs selectively extract Zr and Hf from HNO 3 solutions in the presence of nitrates. Zr is selectively extracted with tetraethyldiamide of heptyl phosphoric acid (in benzene) as well as with 2-thenoyltrifluoroacetone (in an acid). The latter reagents is suitable for rapid determination of 95 Zr in a mixture with 95 Nb and other fragments. The complexometric determination of Zr is based on formation of a stable complex of Zr with EDTA. The titration is carried out in the presence of n-sulfobenzene-azo-pyrocatechol, eriochrome black T. The determination is hindered by Hf, fluoride-, phosphate-, oxalate- and tartrate-ions. The method is used for determining Zr in zircon and eudialyte ore. Zr is determined photometrically with the aid of xylenol orange, arsenazo 3 and pyrocatechol violet (in phosphorites). Hf is determined in the presence of Zr photometrically with the aid of xylenol orange or methyl-thymol blue. The method is based on Zr being masked with hydrogen peroxide in the presence of sulfate-ions

  12. HF Parameters of Induction Motor

    Directory of Open Access Journals (Sweden)

    M. N. Benallal

    2017-09-01

    Full Text Available This article describes the results of experimental studies of HF input and primary parameters. A simulation model in Matlab SimulinkTM of multiphase windings as ladder circuit of coils is developed. A method for determining the primary parameters of ladder equivalent circuits is presented.

  13. Preparation and enhanced oxidation performance of a Hf-doped single-phase Pt-modified aluminide coating

    International Nuclear Information System (INIS)

    Yang, Y.F.; Jiang, C.Y.; Yao, H.R.; Bao, Z.B.; Zhu, S.L.; Wang, F.H.

    2016-01-01

    Graphical abstract: Tiny Hf particles were successfully incorporated into Pt plating via simple electro-plating method. The hafnium particles were either nipped at Pt grain boundaries or wrapped inside Pt grains, and most of them were below 3 μm in size, showing a uniform distribution within the Pt plating. - Highlights: • A Hf-rich belt formed between outer (Ni,Pt)Al and IDZ after aluminisation. • Hf-doped coating showed much decreased mass gain and oxidation rate constant k_p. • Hf-rich belt acted as diffusion barrier by restraining diffusions of Al and W. • Degradation of β was effectively postponed by the unique Hf addition. • Hf-doped coating exhibited lighter oxide scale rumpling tendency. - Abstract: A Hf-doped β-(Ni,Pt)Al coating was prepared by co-deposition of a Pt-Hf composite plating and successive aluminisation. Then, a distinct Hf-rich belt was formed internally between the outer additive (Ni,Pt)Al coating and interdiffusion zone. An isothermal oxidation test at 1100 °C revealed a relatively lower oxidation rate constant and decreased oxide scale rumpling tendency for the Hf-doped coating during which the Hf-rich belt partly acted as an effective diffusion barrier. The unique addition of Hf into a β-(Ni,Pt)Al coating can delay the transitional oxidation period from transient alumina to stable one and postpone the degradation from β to γ'.

  14. Preparation, structure and properties of hafnium compounds in the system Hf-C-N-O

    International Nuclear Information System (INIS)

    Brundiers, G.D.

    1975-08-01

    Highly dense, homogenous and single phase hafnium carbonitride samples (with low oxygen content) were prepared in the whole concentration range of the ternary cubic carbonitrides. Stoichiometric hafnium oxicarbides were also prepared within the range of solubility. The procedure involved the hot pressing of powders of HfC, HfN, Hf, Hf-Oxide and carbon at temperatures of 3,000 0 C and pressures up to 550 kpf/cm 2 using a novel technique. Small single crystals of slightly substoichiometric HfN were also repared. The densification of the powders was studied as a function of the non-metal concentration. Carbonitrides with N/Hf ratio of 0.37 were prepared in a high temperature autoclave operating at medium pressures by the reaction of HfC with nitrogen. All the samples were characterized by density measurements, chemical, X-ray and metallographic analysis and in some cases with the aid of quantitative metallography and microprobe analysis. Typical properties investigated were lattice parameter, thermal expansion, microhardness and electrical resistivity as function of the non-metal content. For specific concentrations extreme values in the properties are attained. With the aid of the valence electron concentration (VEC) parameter, the properties can be correlated with the density of states of electrons at the Fermi level. (orig./HK) [de

  15. Determining characteristics of HF communications links using SuperDARN

    Directory of Open Access Journals (Sweden)

    J. M. Hughes

    2002-07-01

    Full Text Available Space weather effects can strongly influence high-frequency (HF communications by changing the ionospheric environment through which the radio waves propagate. Since many systems utilize HF communications, the ability to make real-time assessments of propagation conditions is an important part of space weather monitoring systems. In this paper, we present new techniques for measuring high-latitude HF communications link parameters using data from SuperDARN radars. These techniques use ground-scatter returns to define the variation in skip distance with frequency. From these data, the maximum usable frequency (MUF as a function of range is determined and ionospheric critical frequencies are estimated. These calculations are made in near-real-time and the results are made available on the World Wide Web. F-region critical frequencies calculated using this method show good agreement with ionosonde data.Key words. Ionosphere (active experiments; instruments and techniques – Radio science (ionospheric propagation

  16. Determining characteristics of HF communications links using SuperDARN

    Directory of Open Access Journals (Sweden)

    J. M. Hughes

    Full Text Available Space weather effects can strongly influence high-frequency (HF communications by changing the ionospheric environment through which the radio waves propagate. Since many systems utilize HF communications, the ability to make real-time assessments of propagation conditions is an important part of space weather monitoring systems. In this paper, we present new techniques for measuring high-latitude HF communications link parameters using data from SuperDARN radars. These techniques use ground-scatter returns to define the variation in skip distance with frequency. From these data, the maximum usable frequency (MUF as a function of range is determined and ionospheric critical frequencies are estimated. These calculations are made in near-real-time and the results are made available on the World Wide Web. F-region critical frequencies calculated using this method show good agreement with ionosonde data.

    Key words. Ionosphere (active experiments; instruments and techniques – Radio science (ionospheric propagation

  17. A novel flow battery: A lead acid battery based on an electrolyte with soluble lead(II). Part IX: Electrode and electrolyte conditioning with hydrogen peroxide

    Science.gov (United States)

    Collins, John; Li, Xiaohong; Pletcher, Derek; Tangirala, Ravichandra; Stratton-Campbell, Duncan; Walsh, Frank C.; Zhang, Caiping

    Extended cycling of a soluble lead acid battery can lead to problems due to an imbalance in the coulombic efficiency leading to deposits of Pb and PbO2 on the electrodes. Periodic addition of hydrogen peroxide to the electrolyte of the soluble lead acid flow battery largely overcomes several operational problems seen during extended cycling, using a 10 cm × 10 cm parallel plate flow cell. It is shown that this treatment greatly extends the number of cycles that can be achieved with a reasonable energy-, voltage-, and charge efficiency of 54-66%, 71%, and 77-91%.

  18. A novel flow battery: A lead acid battery based on an electrolyte with soluble lead(II). Part IX: Electrode and electrolyte conditioning with hydrogen peroxide

    Energy Technology Data Exchange (ETDEWEB)

    Collins, John; Stratton-Campbell, Duncan [C-Tech Innovation Ltd., Capenhurst, Chester CH1 6EH (United Kingdom); Li, Xiaohong; Tangirala, Ravichandra; Walsh, Frank C.; Zhang, Caiping [Energy Technology Research Group, School of Engineering Sciences, University of Southampton, Highfield, University Road, Southampton SO17 1BJ (United Kingdom); Pletcher, Derek [Electrochemistry and Surface Science Group, School of Chemistry, University of Southampton, Southampton SO17 1BJ (United Kingdom)

    2010-05-01

    Extended cycling of a soluble lead acid battery can lead to problems due to an imbalance in the coulombic efficiency leading to deposits of Pb and PbO2 on the electrodes. Periodic addition of hydrogen peroxide to the electrolyte of the soluble lead acid flow battery largely overcomes several operational problems seen during extended cycling, using a 10 cm x 10 cm parallel plate flow cell. It is shown that this treatment greatly extends the number of cycles that can be achieved with a reasonable energy-, voltage-, and charge efficiency of 54-66%, 71%, and 77-91%. (author)

  19. The solubility of solid fission products in carbides and nitrides of uranium and plutonium. Part I: literature review on experimental results

    International Nuclear Information System (INIS)

    Benedict, U.

    1977-01-01

    This review compiles the available data on the solubility of the most important non-volatile fission products in the carbides, nitrides, and carbonitrides of uranium and plutonium. It includes some elements which are not fission products, but belong to a group of the Periodic Table which contains one or more fission products elements

  20. Utilization of antenna arrays in HF systems

    Directory of Open Access Journals (Sweden)

    Louis Bertel

    2009-06-01

    Full Text Available

    Different applications of radio systems are based on the implementation of antenna arrays. Classically, radio direction

    finding operates with a multi channel receiving system connected to an array of receiving antennas. More

    recently, MIMO architectures have been proposed to increase the capacity of radio links by the use of antenna

    arrays at both the transmitter and receiver.

    The first part of this paper describes some novel experimental work carried out to examine the feasibility of applying

    MIMO techniques for communications within the HF radio band. A detailed correlation analysis of a variety

    of different antenna array configurations is presented. The second section of the paper also deals with HF

    MIMO communications, focusing on the problem from a modelling point of view. The third part presents a sensitivity

    analysis of different antenna array structures for HF direction finding applications. The results demonstrate

    that when modelling errors, heterogeneous antenna arrays are more robust in comparison to homogeneous structures


  1. The rotational excitation of HF by H

    Science.gov (United States)

    Desrousseaux, Benjamin; Lique, François

    2018-06-01

    The HF molecule is a key tracer of molecular hydrogen in diffuse interstellar medium (ISM). Accurate modelling of the HF abundance in such media requires one to model its excitation by both radiation and collisions. In diffuse ISM, the dominant collisional partners are atomic and molecular hydrogen. We report quantum time-independent calculations of collisional cross-sections and rate coefficients for the rotational excitation of HF by H. The reactive hydrogen exchange channels are taken into account in the scattering calculations. For the first time, HF-H rate coefficients are provided for temperature ranging from 10 to 500 K. The strongest collision-induced rotational HF transitions are those with Δj = 1, and the order of magnitude of the new HF-H rate coefficients is similar to that of the HF-H2 ones previously computed. As a first application, we simulate the excitation of HF by both H and H2 in typical diffuse ISM. We show that, depending on the rotational transition, hydrogen atoms increase or decrease the simulated excitation temperatures compared to collisional excitation only due to H2 molecules. Such results suggest that the new HF-H collisional data have to be used for properly modelling the abundance of HF in diffuse ISM.

  2. Special Topics in HF Propagation

    Science.gov (United States)

    1979-11-01

    Capitaine de Frigate P.Italley Dr T.SJones Ing6nieur en Chef au CNET Physics Department 38 -40 rue du Gdn~ral Leclerc University of Leicester 9213 i1...fre’qiancý. A t’ctailcd discussion of HF reliability is giver in A companion paiper (MASLIN, N.M . 197(j)) the result tic ligs 4 atad % i-. sumniart-aed...conttoutt to determine if treie :s an additional zonal gqt.ient but wa shall ceo tto.., tnC companion Layttacings that it it, negliit.-tle. F:gur:!i 7A

  3. The part of soluble and insoluble forms of Pb, Be, Ba, Ca, Mg, Sr in particulate matter and in the pharyngeal tonsils

    Directory of Open Access Journals (Sweden)

    Maria Gerycka

    2014-09-01

    Full Text Available Introduction. Previous studies have confirmed that the pharyngeal tonsil is a good biomarker of exposure due to its position relative to inhaled air so that multiple elements can be accumulated in this organ. The aim of the study is to determine the share of soluble and insoluble compounds of individual elements in suspended particles in the accumulation of Pb, Be, Ba, Sr, Ca,Mg by the pharyngeal tonsils. Material and methods. The content of the analyzed elements is defined in 86 samples of pharyngeal tonsils from children living in Tychy and in 76 samples of pharyngeal tonsils from children living in Chorzów, as well as in the suspended particles in the air occurring in soluble and insoluble form. The specified coefficients k1, k2 present in the equation division allow the indication the greater importance of soluble and insoluble fraction of an element present in the inhaled air. Results. The value of the coefficients in the equation division based on gender confirmed its importance. Conclusions. The values detect area variation in relation to passive smoking in the extent of accumulation of Pb, Be, Ba, Sr, Mg, Ca in pharyngeal tonsils.

  4. Myeloid-derived suppressor cells in murine AIDS inhibit B-cell responses in part via soluble mediators including reactive oxygen and nitrogen species, and TGF-β

    Energy Technology Data Exchange (ETDEWEB)

    Rastad, Jessica L. [Department of Microbiology and Immunology, Geisel School of Medicine at Dartmouth, Lebanon, NH 03756 (United States); Green, William R., E-mail: William.R.Green@dartmouth.edu [Department of Microbiology and Immunology, Geisel School of Medicine at Dartmouth, Lebanon, NH 03756 (United States); Norris Cotton Cancer Center, Geisel School of Medicine at Dartmouth, Lebanon, NH 03756 (United States)

    2016-12-15

    Monocytic myeloid-derived suppressor cells (M-MDSCs) were increased during LP-BM5 retroviral infection, and were capable of suppressing not only T-cell, but also B-cell responses. In addition to previously demonstrating iNOS- and VISTA-dependent M-MDSC mechanisms, in this paper, we detail how M-MDSCs utilized soluble mediators, including the reactive oxygen and nitrogen species superoxide, peroxynitrite, and nitric oxide, and TGF-β, to suppress B cells in a predominantly contact-independent manner. Suppression was independent of cysteine-depletion and hydrogen peroxide production. When two major mechanisms of suppression (iNOS and VISTA) were eliminated in double knockout mice, M-MDSCs from LP-BM5-infected mice were able to compensate using other, soluble mechanisms in order to maintain suppression of B cells. The IL-10 producing regulatory B-cell compartment was among the targets of M-MDSC-mediated suppression. -- Highlights: •LP-BM5-expanded M-MDSCs utilized soluble mediators nitric oxide, superoxide, peroxynitrite, and TGF-β to suppress B cells. •When two major mechanisms of suppression were eliminated through knockouts, M-MDSCs maintained suppression. •M-MDSCs from LP-BM5-infected mice decreased proliferation of IL-10 producing regulatory B cells.

  5. Myeloid-derived suppressor cells in murine AIDS inhibit B-cell responses in part via soluble mediators including reactive oxygen and nitrogen species, and TGF-β

    International Nuclear Information System (INIS)

    Rastad, Jessica L.; Green, William R.

    2016-01-01

    Monocytic myeloid-derived suppressor cells (M-MDSCs) were increased during LP-BM5 retroviral infection, and were capable of suppressing not only T-cell, but also B-cell responses. In addition to previously demonstrating iNOS- and VISTA-dependent M-MDSC mechanisms, in this paper, we detail how M-MDSCs utilized soluble mediators, including the reactive oxygen and nitrogen species superoxide, peroxynitrite, and nitric oxide, and TGF-β, to suppress B cells in a predominantly contact-independent manner. Suppression was independent of cysteine-depletion and hydrogen peroxide production. When two major mechanisms of suppression (iNOS and VISTA) were eliminated in double knockout mice, M-MDSCs from LP-BM5-infected mice were able to compensate using other, soluble mechanisms in order to maintain suppression of B cells. The IL-10 producing regulatory B-cell compartment was among the targets of M-MDSC-mediated suppression. -- Highlights: •LP-BM5-expanded M-MDSCs utilized soluble mediators nitric oxide, superoxide, peroxynitrite, and TGF-β to suppress B cells. •When two major mechanisms of suppression were eliminated through knockouts, M-MDSCs maintained suppression. •M-MDSCs from LP-BM5-infected mice decreased proliferation of IL-10 producing regulatory B cells.

  6. MO-HF-C alloy composition

    International Nuclear Information System (INIS)

    Whelan, E.P.; Kalns, E.

    1987-01-01

    This patent describes, as an article of manufacture, a cast ingot of a molybdenum-hafnium-carbon alloy consisting essentially by weight of about 0.6% to about 1% Hf, about 0.045% to about 0.08% C, and the balance essentially molybdenum. The amount of Hf and C present are substantially stoichiometric with respect to HfC and within about +-15% of stoichiometry. The ingot is characterized in that it has a substantially less tendency to crack compared to alloys containing Hf in excess of about 1% by weight and carbon in excess of 0.08% by weight, without substantial diminution in strength properties of the alloy

  7. Solid dispersions, part I: recent evolutions and future opportunities in manufacturing methods for dissolution rate enhancement of poorly water-soluble drugs.

    Science.gov (United States)

    Bikiaris, Dimitrios N

    2011-11-01

    In recent years, the number of active pharmaceutical ingredients with high therapeutic impact, but very low water solubility, has increased significantly. Thus, a great challenge for pharmaceutical technology is to create new formulations and efficient drug-delivery systems to overcome these dissolution problems. Drug formulation in solid dispersions (SDs) is one of the most commonly used techniques for the dissolution rate enhancement of poorly water-soluble drugs. Generally, SDs can be defined as a dispersion of active ingredients in molecular, amorphous and/or microcrystalline forms into an inert carrier. This review covers literature which states that the dissolution enhancement of SDs is based on the fact that drugs in the nanoscale range, or in amorphous phase, dissolve faster and to a greater extent than micronized drug particles. This is in accordance to the Noyes-Whitney equation, while the wetting properties of the used polymer may also play an important role. The main factors why SD-based pharmaceutical products on the market are steadily increasing over the last few years are: the recent progress in various methods used for the preparation of SDs, the effect of evolved interactions in physical state of the drug and formulation stability during storage, the characterization of the physical state of the drug and the mechanism of dissolution rate enhancement.

  8. Exploratory studies on substitutions in the tetrahedrite-tennantite solid solution series Part III. The solubility of bismuth in tetrahedrite-tennantite containing iron and zinc

    DEFF Research Database (Denmark)

    Hansen, K.M.; Karup-Møller, Sven; Makovicky, E.

    2003-01-01

    Bismuth-bearing tetrahedrite and termanite were synthesized from dry runs in evacuated silica glass tubes at 350 degreesC, 450 degreesC and 520 degreesC, and studied by means of microprobe analyses on polished sections and X-ray powder diffraction. Charges were prepared with two Zn or Fe atoms p.f.u......., with pure As, resp. Sb, or with As: Sb = 1: 1. They were prepared with one and two atoms of Bi p.f.u., respectively, at all three temperatures. Separate sets of non-stoichiometric compositions were prepared in order to examine the influence of high- and low sulfur fugacity, respectively, on the solubility...... of Bi in tetrahedrite/termantite. Our studies suggest that the solubility of Bi in tetrahedrite-termanite is 0.8 atom p.f.u. at 350 degreesC and I atom p.f.u. at 450 degreesC and 520 degreesC, independent of the Sb/As ratio. It increases with the increase in S fugacity and vice versa. The average...

  9. Radiation grafting of various water-soluble monomers on ultra-high molecular weight polyethylene powder. Part II: Thermal, FTIR and morphological characterisation

    Energy Technology Data Exchange (ETDEWEB)

    Aydinli, Bahattin; Tincer, Teoman E-mail: teotin@metu.edu.tr

    2001-10-01

    Radiation induced grafted polyacrylic acid (PAA), polymethacrylic acid (PMAA), polyacrylamide (PAAm), poly N,N-dimethyl acrylamide (PNDAAm) and poly 1-vinyl-2 pyrrolidone (PVP) on ultra-high molecular weight polyethylene (UHMWPE) were characterised by DSC, FTIR and SEM analysis. While the effect of irradiation on pure UHMWPE was found to increase crystallinity and cause higher enthalpy of crystallisation, grafted UHMWPE powders showed lower crystallinity and enthalpy of crystallisation. In all grafted UHMWPE there existed secondary transitions corresponding to grafting polymers in the first run of DSC above 60 deg. C and they became clearer at a higher grafting level. In the second run of DSC some T{sub g} values appeared to shift to higher temperatures while some were not detected. FTIR analysis indicated the presence of water-soluble polymers in the grafted UHMWPE. The characteristic peaks of water-soluble polymers became sharper in the grafted UHMWPE. SEM analysis revealed that the grafting occurs both on fiber and microparticles of UHMWPE while flowing characteristic of powder is retained.

  10. Radiation grafting of various water-soluble monomers on ultra-high molecular weight polyethylene powder. Part II: Thermal, FTIR and morphological characterisation

    Science.gov (United States)

    Aydınlı, Bahattin; Tin c̡er, Teoman

    2001-10-01

    Radiation induced grafted polyacrylic acid (PAA), polymethacrylic acid (PMAA), polyacrylamide (PAAm), poly N,N-dimethyl acrylamide (PNDAAm) and poly 1-vinyl-2 pyrrolidone (PVP) on ultra-high molecular weight polyethylene (UHMWPE) were characterised by DSC, FTIR and SEM analysis. While the effect of irradiation on pure UHMWPE was found to increase crystallinity and cause higher enthalpy of crystallisation, grafted UHMWPE powders showed lower crystallinity and enthalpy of crystallisation. In all grafted UHMWPE there existed secondary transitions corresponding to grafting polymers in the first run of DSC above 60°C and they became clearer at a higher grafting level. In the second run of DSC some Tg values appeared to shift to higher temperatures while some were not detected. FTIR analysis indicated the presence of water-soluble polymers in the grafted UHMWPE. The characteristic peaks of water-soluble polymers became sharper in the grafted UHMWPE. SEM analysis revealed that the grafting occurs both on fiber and microparticles of UHMWPE while flowing characteristic of powder is retained.

  11. Development of HF-systems for electron storage systems

    International Nuclear Information System (INIS)

    Androsov, V.P.; Karnaukhov, I.M.; Popkov, Yu.P.; Reva, S.N.; Telegin, Yu.N.

    1999-01-01

    Development of HF systems for electron storages is described. Its final task is construction of 100 kW HF station at 699,3 MHz frequency consisting from low-power HF system, klystron amplifier, wave line for HF power transmission and accelerating section. Functional parameters of HF station are given

  12. Positron annihilation studies in Hf doped YBCO

    International Nuclear Information System (INIS)

    Gopalan, P.; Priya, E.R.; Premila, M.; Sundar, C.S.; Gopinathan, K.P.

    1992-01-01

    The variation of positron lifetime and oxygen stoichiometry as a function of quench temperature has been measured in undoped and 0.5at%, 0.75at%, and 1.0 at% Hf doped YBCO. In both the undoped and Hf doped samples, the lifetime decreases and the oxygen content increases as the quench temperature is lowered from 900degC to 300degC. The lifetime in the tetragonal phase (900degC) decreases with the increase in Hf content, whereas in the orthorhombic phase (450degC) it increases. The difference in lifetime between the tetragonal and orthorhombic phases decreases with the increase in the Hf content. These trends are discussed in terms of the influence of Hf doping on the oxygen content and the positron density distribution in YBCO

  13. 40 CFR Table 7 to Subpart Vvvvvv... - Partially Soluble HAP

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 14 2010-07-01 2010-07-01 false Partially Soluble HAP 7 Table 7 to... Pt. 63, Subpt. VVVVVV, Table 7 Table 7 to Subpart VVVVVV of Part 63—Partially Soluble HAP As required... partially soluble HAP listed in the following table. Partially soluble HAP name CAS No. 1. 1,1,1...

  14. The guanidinium group as a key part of water-soluble polymer carriers for siRNA complexation and protection against degradation.

    Science.gov (United States)

    Tabujew, Ilja; Freidel, Christoph; Krieg, Bettina; Helm, Mark; Koynov, Kaloian; Müllen, Klaus; Peneva, Kalina

    2014-07-01

    Here, the preparation of a novel block copolymer consisting of a statistical copolymer N-(2-hydroxypropyl) methacrylamide-s-N-(3-aminopropyl) methacrylamide and a short terminal 3-guanidinopropyl methacrylamide block is reported. This polymer structure forms neutral but water-soluble nanosized complexes with siRNA. The siRNA block copolymer complexes are first analyzed using agarose gel electrophoresis and their size is determined with fluorescence correlation spectroscopy. The protective properties of the polymer against RNA degradation are investigated by treating the siRNA block copolymer complexes with RNase V1. Heparin competition assays confirm the efficient release of the cargo in vitro. In addition, the utilization of microscale thermophoresis is demonstrated for the determination of the binding strength between a fluorescently labeled polyanion and a polymer molecule. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Lu-Hf isotope systematics of fossil biogenic apatite and their effects on geochronology

    Science.gov (United States)

    Herwartz, Daniel; Münker, Carsten; Tütken, Thomas; Hoffmann, J. Elis; Wittke, Andreas; Barbier, Bruno

    2013-01-01

    Reliable methods for direct dating of biogenic apatite from pre-Pleistocene fossils are currently not available, and recent attempts using the Lu-Hf decay system yielded highly inaccurate ages for both bones and teeth. The geological processes accounting for this poor accuracy of Lu-Hf chronometry are not yet understood. Here we explore Lu-Hf systematics in fossil bones and teeth in detail, by applying five different sample digestion techniques that are tested on bones and composites of bone and sediment. Our current dataset implies that dissolution methods only slightly affect the resulting Lu-Hf ages, while clear differences between the individual digestion techniques became apparent for element concentrations. By analysing the insoluble leftovers from incomplete sample dissolution, four main reservoirs of Hf in fossil bones were identified: (1) a radiogenic end-member associated with apatite; (2) an unradiogenic end-member represented by the authigenic minerals or the embedding sediment; (3) a highly unradiogenic end-member that can be attributed to detrital zircon; and (4) a moderately soluble phase (probably a Zr(Hf)-phosphate) that yielded very low Lu/Hf but a highly radiogenic Hf isotope composition at the same time. This Zr(Hf)-phase must have been precipitated within the fossil bone sample at a late stage of burial history, thereby incorporating radiogenic 176Hf released from apatite surfaces over geological timescales. A second focus of our study is the effect of different sediment matrices and of crystal size on the preservation of pristine Lu-Hf isotope compositions in bioapatite. Because near-depositional Lu-Hf ages of phosphate fossils have previously been reported for the London Clay (England) and a calcareous marl from Tendaguru (Tanzania), we herein investigate specimens fossilised in carbonate matrices (calcareous marl from Oker, Germany; carbonate concretions from the Santana Formation, Brazil; carbonate from the Eifel, Germany) and argillaceous

  16. 3 and 4 oxidation state element solubilities in borosilicate glasses. Implement to actinides in nuclear glasses

    International Nuclear Information System (INIS)

    Cachia, J.N.

    2005-12-01

    In order to ensure optimal radionuclides containment, the knowledge of the actinide loading limits in nuclear waste glasses and also the comprehension of the solubilization mechanisms of these elements are essential. A first part of this manuscript deals with the study of the differences in solubility of the tri and tetravalent elements (actinides and surrogates) particularly in function of the melting temperature. The results obtained indicate that trivalent elements (La, Gd, Nd, Am, Cm) exhibit a higher solubility than tetravalent elements (Hf, Th, Pu). Consequently, it was planned to reduce plutonium at the oxidation state (III), the later being essentially tetravalent in borosilicate glasses. An innovating reduction process of multi-valent elements (cerium, plutonium) using silicon nitride has been developed in a second part of this work. Reduced plutonium-bearing glasses synthesized by Si 3 N 4 addition made it possible to double the plutonium solubility from 2 to 4 wt% at 1200 deg C. A structural approach to investigate the differences between tri and tetravalent elements was finally undertaken. These investigations were carried out by X-rays Absorption Spectroscopy (EXAFS) and NMR. Trivalent rare earth and actinide elements seem to behave as network modifiers while tetravalent elements rather present true intermediaries' behaviour. (author)

  17. Aspects of HF radio propagation

    Directory of Open Access Journals (Sweden)

    Stephane Saillant

    2009-06-01

    Full Text Available

    radio systems. From the point of view Working Group 2 of the COST 296 Action, interest lies with effects associated

    with propagation via the ionosphere of signals within the HF band. Several aspects are covered in this paper:

    a The directions of arrival and times of flight of signals received over a path oriented along the trough have

    been examined and several types of propagation effects identified. Of particular note, combining the HF observations

    with satellite measurements has identified the presence of irregularities within the floor of the trough that

    result in propagation displaced from the great circle direction. An understanding of the propagation effects that

    result in deviations of the signal path from the great circle direction are of particular relevance to the operation

    of HF radiolocation systems.

    b Inclusion of the results from the above mentioned measurements into a propagation model of the northerly

    ionosphere (i.e. those regions of the ionosphere located poleward of, and including, the mid-latitude trough

    and the use of this model to predict the coverage expected from transmitters where the signals impinge on the

    northerly ionosphere

  18. Picture analysis in CT-HF and its CT photographs

    International Nuclear Information System (INIS)

    Kubota, Kazuo; Kohirasawa, Hideo; Shinojima, Masayasu; Tokui, Mitsuru; Seo, Kunihiko.

    1980-01-01

    CT (computed tomography) apparatus is rarely used yet in the field of dentistry, though it seems useful. It is possibly because of the artefacts caused by the metallic parts attached to teeth, the large partial volume effect due to many bones and the problems of positioning and reproducibility. After considering the various requirements of the CT apparatuses in dental field, CT-HF (of T/R type) was chosen as such apparatus, and installed as the first in dentistry. In the CT-HF apparatus, the inner diameter of the gantry is up to 300 mm, and the position of a tomographic plane is only 40 mm away from the front of gantry. Mainly the usefulness of scanography in positioning and the usefulness of the CT apparatus in the picture analysis and processing in dental field are described. (J.P.N.)

  19. Grindability of cast Ti-Hf alloys.

    Science.gov (United States)

    Kikuchi, Masafumi; Takahashi, Masatoshi; Sato, Hideki; Okuno, Osamu; Nunn, Martha E; Okabe, Toru

    2006-04-01

    As part of our systematic studies characterizing the properties of titanium alloys, we investigated the grindability of a series of cast Ti-Hf alloys. Alloy buttons with hafnium concentrations up to 40 mass% were made using an argon-arc melting furnace. Each button was cast into a magnesia-based mold using a dental titanium casting machine; three specimens were made for each metal. Prior to testing, the hardened surface layer was removed. The specimens were ground at five different speeds for 1 min at 0.98 N using a carborundum wheel on an electric dental handpiece. Grindability was evaluated as the volume of metal removed per minute (grinding rate) and the volume ratio of metal removed compared to the wheel material lost (grinding ratio). The data were analyzed using ANOVA. A trend of increasing grindability was found with increasing amounts of hafnium, although there was no statistical difference in the grindability with increasing hafnium contents. We also found that hafnium may be used to harden or strengthen titanium without deteriorating the grindability.

  20. Microhardness evaluation alloys Hf-Si-B; Avaliacao de microdureza de ligas Hf-Si-B

    Energy Technology Data Exchange (ETDEWEB)

    Gigolotti, Joao Carlos Janio; Costa, Eliane Fernandes Brasil [Centro Universitario de Volta Redonda (UNIFOA), Volta Redonda, RJ (Brazil); Nunes, Carlos Angelo; Rocha, Elisa Gombio; Coelho, Gilberto Carvalho, E-mail: carlosjanio@uol.com.br, E-mail: eliane-costabrasi@hotmail.com, E-mail: cnunes@demar.eel.usp.br, E-mail: elisarocha@alunos.eel.usp.br, E-mail: coelho@demar.eel.usp.br [Universidade de Sao Paulo (USP), Lorena, SP (Brazil)

    2014-08-15

    The technological advance has generated increasing demand for materials that can be used under high temperature, what includes intermetallic MR-Si-B (MR = refractory metal) alloys with multiphase structures, that can also be applied in oxide environments. Thus, this work had for objective the micro hardness study of the Hf-Si-B system alloys, heat treated at 1600 deg C, in the Hf rich region. Hf-Si-B alloys had been produced with blades of Hf (min. 99.8%), Si (min. 99.998%) and B (min. 99.5%), in the voltaic arc furnace and heat treated at 1600 deg C under argon atmosphere. The relationship of the phases had been previously identified by X-ray diffraction and contrast in backscattered electron imaging mode. The alloys had their hardness analyzed by method Vickers (micro hardness) with load of 0.05 kgf and 0.2 kgf and application time of 20 s. The results, obtained from the arithmetic mean of measurements for each alloy on the heterogeneous region, showed a mean hardness of 11.08 GPA, with small coefficient of variation of 3.8%. The borides HfB2 (19.34 GPa) e HfB - 11.76 GPa, showed the hardness higher than the silicides Hf2Si (8.57 GPa), Hf5Si3 (9.63 GPa), Hf3Si2 (11.66 GPa), Hf5Si4 (10.00 GPa), HfSi (10.02 GPa) e HfSi2 (8.61 GPa). (author)

  1. Heavy ion studies with CMS HF calorimeter

    International Nuclear Information System (INIS)

    Damgov, I.; Genchev, V.; Kolosov, V.A.; Lokhtin, I.P.; Petrushanko, S.V.; Sarycheva, L.I.; Teplov, S.Yu.; Shmatov, S.V.; Zarubin, P.I.

    2001-01-01

    The capability of the very forward (HF) calorimeter of the CMS detector at LHC to be applied to specific studies with heavy ion beams is discussed. The simulated responses of the HF calorimeter to nucleus-nucleus collisions are used for the analysis of different problems: reconstruction of the total energy flow in the forward rapidity region, accuracy of determination of the impact parameter of collision, study of fluctuations of the hadronic-to-electromagnetic energy ratio, fast inelastic event selection

  2. Gas solubilities widespread applications

    CERN Document Server

    Gerrard, William

    1980-01-01

    Gas Solubilities: Widespread Applications discusses several topics concerning the various applications of gas solubilities. The first chapter of the book reviews Henr's law, while the second chapter covers the effect of temperature on gas solubility. The third chapter discusses the various gases used by Horiuti, and the following chapters evaluate the data on sulfur dioxide, chlorine data, and solubility data for hydrogen sulfide. Chapter 7 concerns itself with solubility of radon, thoron, and actinon. Chapter 8 tackles the solubilities of diborane and the gaseous hydrides of groups IV, V, and

  3. Solubility limits of importance to leaching

    International Nuclear Information System (INIS)

    Ogard, A.; Bentley, G.; Bryant, E.; Duffy, C.; Grisham, J.; Norris, E.; Orth, C.; Thomas, K.

    1981-01-01

    The solubilities of some radionuclides, especially rare earths and actinides, may be an important and controlling factor in leaching of waste forms. These solubilities should be measured accurately as a function of pH and not as a part of a multicomponent system. Individual solubilities should be measured as a function of temperature to determine if a kinetic effect is being observed in the data. A negative temperature coefficient of solubility for actinides and rare earths in water would have important consequences for nuclear reactor safety and for the management of nuclear wastes

  4. Determination of the rate of HF hydration and the effects of HF on moisture condensation

    International Nuclear Information System (INIS)

    McCulla, W.H.

    1982-01-01

    There were four basic questions addressed in this report that relate to the HF interaction in the environment. As to whether HF hydrates in the vapor phase and what the rate of that hydration is, there seems ample evidence that HF hydrates readily in the vapor phase and the rate of that hydration is very fast, i.e., dHF/dt greater than or equal to 25 torr sec -1 . Concerning under what conditions condensation of the hydrate will occur and whether a third body is required for condensation, it was found that HF does effect the dew point or condensation of water and data was presented indicating the extent of that effect. It was also determined that condensation will occur without a third body present. Thus, in attempting to model an HF release for the Safety Analysis Report the hydration of HF and the subsequent heat released may be treated as occurring instantaneously; but the ultimate disposition of the HF will be strongly dependent upon the environmental conditions at the time of the release

  5. Determination of the rate of HF hydration and the effects of HF on moisture condensation

    Energy Technology Data Exchange (ETDEWEB)

    McCulla, W H

    1982-04-30

    There were four basic questions addressed in this report that relate to the HF interaction in the environment. As to whether HF hydrates in the vapor phase and what the rate of that hydration is, there seems ample evidence that HF hydrates readily in the vapor phase and the rate of that hydration is very fast, i.e., dHF/dt greater than or equal to 25 torr sec/sup -1/. Concerning under what conditions condensation of the hydrate will occur and whether a third body is required for condensation, it was found that HF does effect the dew point or condensation of water and data was presented indicating the extent of that effect. It was also determined that condensation will occur without a third body present. Thus, in attempting to model an HF release for the Safety Analysis Report the hydration of HF and the subsequent heat released may be treated as occurring instantaneously; but the ultimate disposition of the HF will be strongly dependent upon the environmental conditions at the time of the release.

  6. Effect of Vericiguat, a Soluble Guanylate Cyclase Stimulator, on Natriuretic Peptide Levels in Patients With Worsening Chronic Heart Failure and Reduced Ejection Fraction

    DEFF Research Database (Denmark)

    Gheorghiade, Mihai; Greene, Stephen J; Butler, Javed

    2015-01-01

    IMPORTANCE: Worsening chronic heart failure (HF) is a major public health problem. OBJECTIVE: To determine the optimal dose and tolerability of vericiguat, a soluble guanylate cyclase stimulator, in patients with worsening chronic HF and reduced left ventricular ejection fraction (LVEF). DESIGN, ...

  7. Soluble Fermentable Dietary Fibre (Pectin) Decreases Caloric Intake, Adiposity and Lipidaemia in High-Fat Diet-Induced Obese Rats

    Science.gov (United States)

    Adam, Clare L.; Thomson, Lynn M.; Williams, Patricia A.; Ross, Alexander W.

    2015-01-01

    Consumption of a high fat diet promotes obesity and poor metabolic health, both of which may be improved by decreasing caloric intake. Satiety-inducing ingredients such as dietary fibre may be beneficial and this study investigates in diet-induced obese (DIO) rats the effects of high or low fat diet with or without soluble fermentable fibre (pectin). In two independently replicated experiments, young adult male DIO rats that had been reared on high fat diet (HF; 45% energy from fat) were given HF, low fat diet (LF; 10% energy from fat), HF with 10% w/w pectin (HF+P), or LF with 10% w/w pectin (LF+P) ad libitum for 4 weeks (n = 8/group/experiment). Food intake, body weight, body composition (by magnetic resonance imaging), plasma hormones, and plasma and liver lipid concentrations were measured. Caloric intake and body weight gain were greatest in HF, lower in LF and HF+P, and lowest in the LF+P group. Body fat mass increased in HF, was maintained in LF, but decreased significantly in LF+P and HF+P groups. Final plasma leptin, insulin, total cholesterol and triglycerides were lower, and plasma satiety hormone PYY concentrations were higher, in LF+P and HF+P than in LF and HF groups, respectively. Total fat and triglyceride concentrations in liver were greatest in HF, lower in LF and HF+P, and lowest in the LF+P group. Therefore, the inclusion of soluble fibre in a high fat (or low fat) diet promoted increased satiety and decreased caloric intake, weight gain, adiposity, lipidaemia, leptinaemia and insulinaemia. These data support the potential of fermentable dietary fibre for weight loss and improving metabolic health in obesity. PMID:26447990

  8. High-K rotational bands in {sup 174}Hf and {sup 175}Hf

    Energy Technology Data Exchange (ETDEWEB)

    Gjoerup, N L; Sletten, G [The Niels Bohr Institute, Roskilbe (Denmark); Walker, P M [Surrey Univ., Guildford (United Kingdom). Dept. of Physics; Bentley, M A [Daresbury Lab. (United Kingdom); Cullen, D M; Sharpey-Schafer, J F; Fallon, P; Smith, G [Liverpool Univ. (United Kingdom). Oliver Lodge Lab.

    1992-08-01

    High sensitivity experiments with {sup 48}Ca, {sup 18}O and {sup 9}Be induced reactions using the ESSA-30, TESSA-3 and NORDBALL arrays have provided extensive new information on the high spin level structures of {sup 174}Hf and {sup 175}Hf. During the series of experiments, several new bands have been found and most known bands have been extended considerably. Spin and excitation energy ranges for {sup 174}Hf are now {approx} 35 {Dirac_h} and {approx} 13 MeV, respectively, and for {sup 175}Hf ranges are {approx} 30 {Dirac_h} and {approx} 7 MeV. respectively. Several new high-K structures have been found in {sup 174}Hf and the structure of these and the already known high-K bands in both nuclei together with the new Tilted Axis Cranking approach might explain the small K-hindrances observed for K-isomers in this region. (author). 8 refs., 2 figs.

  9. Neptunium (IV) oxalate solubility

    International Nuclear Information System (INIS)

    Luerkens, D.W.

    1983-07-01

    The equilibrium solubility of neptunium (IV) oxalate in nitric/oxalic acid solutions was determined at 22 0 C, 45 0 C, and 60 0 C. The concentrations of nitric/oxalic acid solutions represented a wide range of free oxalate ion concentration. A mathematical solubility model was developed which is based on the formation of the known complexes of neptunium (IV) oxalate. the solubility model uses a simplified concentration parameter which is proportional to the free oxalate ion concentration. The solubility model can be used to estimate the equilibrium solubility of neptunium (IV) oxalate over a wide range of oxalic and nitric acid concentrations at each temperature

  10. Comparison of HfCl4, HfI4, TEMA-Hf, and TDMA-Hf as precursors in early growing stages of HfO2 films deposited by ALD: A DFT study

    Science.gov (United States)

    Cortez-Valadez, M.; Fierro, C.; Farias-Mancilla, J. R.; Vargas-Ortiz, A.; Flores-Acosta, M.; Ramírez-Bon, R.; Enriquez-Carrejo, J. L.; Soubervielle-Montalvo, C.; Mani-Gonzalez, P. G.

    2016-06-01

    The final structure of HfO2 films grown by atomic layer deposition (ALD) after reaction with OH- ions has been analyzed by DFT (density functional theory). The interaction of the precursors: HfCl4 (hafnium tetrachloride), HfI4 (hafnium tetraiodide), TEMA-Hf (tetrakis-ethylmethylamino hafnium), and TDMA-Hf (tetrakis-dimethylamino hafnium) with HO-H was studied employing the B3LYP (Becke 3-parameter, Lee-Yang-Parr) hybrid functional and the PBE (Perdew-Burke-Ernzerhof) generalized gradient functional. The structural evolution at the Si(100) surface has been analyzed by LDA (local density approximation). The structural parameters: bond length and bond angle, and the vibrational parameters for the optimized structures are also reported. The presence of hafnium silicate at the interface was detected. The infrared spectra and structural parameters obtained in this work agree with previously reported experimental results.

  11. Searching triaxial superdeformation in 175Hf

    International Nuclear Information System (INIS)

    Li Xiaowei; Zhejiang Normal Univ., Jinhua; Yu Shaoying; Zhejiang Normal Univ., Jinhua; Chinese Academy of Sciences, Beijing; Shen Caiwan; National Laboratory of Heavy Ion Accelerator of Lanzhou, Lanzhou; Chen Yongshou; Chinese Academy of Sciences, Beijing; National Laboratory of Heavy Ion Accelerator of Lanzhou

    2006-01-01

    A two-dimensional Total Routhian Surface (TRS) calculation is carried out in order to ascertain if there is triaxial superdeformation in 175 Hf. A five quasi-particle configuration is chosen in the calculation. Unfortunately, the TRS minimum does not show up in the total potential energy surface. (authors)

  12. Ferromagnetic characteristics of HfFe2

    International Nuclear Information System (INIS)

    Novakovic, N.; Belosevic-Cavor, J.; Cekic, B.; Manasijevic, M.; Milosevic, Z. . E-mail address of correspoding author: novnik@rt270.vin.bg.ac.yu; Novakovic, N.)

    2003-01-01

    The magnetic hyperfine fields at 181 Ta ion-probe sites in the HfFe 2 polycrystalline binary compound were measured using the time-differential perturbed angular correlation (TDPAC) method. Measurements were performed in the absence of polarizing external magnetic field, at room temperature. The existence of two different structures, dominant cubic MgCu 2 -type and hexagonal MgZn 2 -type in our HfFe 2 sample was refined. Both structures are ferromagnetic with Curie temperatures, which differ significantly (588 K for MgCu 2 and 427 K for MgZn 2 ). The corresponding values of hyperfine fields are H hf 13.8±0.1 T for MgCu 2 -type structure and H hf = 8.0±0.2 T for MgZn 2 -type structure. Calculations using LAPW-Wien 97 program package are in progress and preliminary results are in good agreement with experiment. The analysis includes qualitative explanation of the exchange interactions mechanism between magnetic dipole moment of the observed 181 Ta ion-probe and magnetic dipole moments of the nearest neighbours on the corresponding coordination polyhedra. All these results will be published recently. (author)

  13. Statistical gamma transitions in {sup 174}Hf

    Energy Technology Data Exchange (ETDEWEB)

    Farris, L P; Cizewski, J A; Brinkman, M J; Henry, R G; Lee, C S [Rutgers--the State Univ., New Brunswick, NJ (United States); Khoo, T L; Janssens, R V.F.; Moore, E F; Carpenter, M P; Ahmad, I; Lauritsen, T [Argonne National Lab., IL (United States); Kolata, J J; Beard, K B; Ye, B; Garg, U [Notre Dame Univ., IN (United States); Kaplan, M S; Saladin, J X; Winchell, D [Pittsburgh Univ., PA (United States)

    1992-08-01

    The statistical spectrum extracted from the {sup 172}Yb({alpha},2n){sup 174}Hf reaction was fit with Monte Carlo simulations using a modified GDR E1 strength function and several formulations of the level density. (author). 15 refs., 1 tab., 3 figs.

  14. Solubility database for TILA-99

    Energy Technology Data Exchange (ETDEWEB)

    Vuorinen, U.; Carlsson, T. [VTT Chemical Technology, Espoo (Finland); Kulmala, S.; Hakanen, M. [Helsinki Univ. (Finland). Lab. of Radiochemistry; Ahonen, L. [Geological Survey of Finland, Espoo (Finland)

    1998-11-01

    The safety assessment of spent fuel disposal requires solubility values for several elements estimated in Finnish disposal conditions. In Finland four sites (Haestholmen, Kivetty, Olkiluoto and Romuvaara) are investigated for the disposal of spent fuel. Haestholmen and OLkiluoto are onshore sites, while Kivetty and Romuvaara are inland sites. Based on groundwater analysis and classification according to salinity at the planned disposal depth mainly fresh groundwater is encountered at Kivetty and Romuvaara, while brackish and saline water-types are met at Haestholmen and Olkiluoto. Very saline, almost brine-type water ({approx}70 g/l) has been found in the deepest parts of the investigated bedrock at one of the sites (Olkiluoto). The reference waters and conditions were chosen according to the water-types. The considered reference conditions incorporated both the near- and far-field, and both oxidizing and reducing conditions were considered. In the reference conditions, the changes in solubilities were also estimated as caused by possible variations in the pH, carbonate content and redox conditions. Uranium, which is the main component of spent fuel is dealt with in a separate report presenting the solubility of uranium and spent fuel dissolution. In this work the solubilities of all the other elements of concern (Am, Cu, Nb, Np, Pa, Pd, Pu, Ra, Se, Sn, Tc, Zr, Cm, Ni, Sr, Th, C, Cl, Cs, Fe, Ho, I, and Sm) in the safety assessment are considered. Some discussion on the corrosion of the spent fuel canister is also presented. For the estimation of solubilities of the elements in question, literature data was collected that mainly comprised experimentally measured concentrations. The sources used were spent fuel experiments, concentrations measured in solubility measurements, natural concentrations and concentrations from natural analogue sites (especially Palmottu and Hyrkkoelae in Finland) as well as the concentrations measured at the Finnish investigation sites

  15. Solubility database for TILA-99

    International Nuclear Information System (INIS)

    Vuorinen, U.; Carlsson, T.; Kulmala, S.; Hakanen, M.

    1998-11-01

    The safety assessment of spent fuel disposal requires solubility values for several elements estimated in Finnish disposal conditions. In Finland four sites (Haestholmen, Kivetty, Olkiluoto and Romuvaara) are investigated for the disposal of spent fuel. Haestholmen and OLkiluoto are onshore sites, while Kivetty and Romuvaara are inland sites. Based on groundwater analysis and classification according to salinity at the planned disposal depth mainly fresh groundwater is encountered at Kivetty and Romuvaara, while brackish and saline water-types are met at Haestholmen and Olkiluoto. Very saline, almost brine-type water (∼70 g/l) has been found in the deepest parts of the investigated bedrock at one of the sites (Olkiluoto). The reference waters and conditions were chosen according to the water-types. The considered reference conditions incorporated both the near- and far-field, and both oxidizing and reducing conditions were considered. In the reference conditions, the changes in solubilities were also estimated as caused by possible variations in the pH, carbonate content and redox conditions. Uranium, which is the main component of spent fuel is dealt with in a separate report presenting the solubility of uranium and spent fuel dissolution. In this work the solubilities of all the other elements of concern (Am, Cu, Nb, Np, Pa, Pd, Pu, Ra, Se, Sn, Tc, Zr, Cm, Ni, Sr, Th, C, Cl, Cs, Fe, Ho, I, and Sm) in the safety assessment are considered. Some discussion on the corrosion of the spent fuel canister is also presented. For the estimation of solubilities of the elements in question, literature data was collected that mainly comprised experimentally measured concentrations. The sources used were spent fuel experiments, concentrations measured in solubility measurements, natural concentrations and concentrations from natural analogue sites (especially Palmottu and Hyrkkoelae in Finland) as well as the concentrations measured at the Finnish investigation sites. The

  16. The Effectiveness of HCl and HF Cleaning of Si0.85Ge0.15 Surface

    International Nuclear Information System (INIS)

    Sun, Y

    2008-01-01

    The cleaning of Si 0.85 Ge 0.15 surfaces using HCl and HF solutions is studied using synchrotron radiation photoelectron spectroscopy. The HF solution is found to be effective in removing both the Si oxide and the Ge oxide while the HCl solution can only remove part of the Ge oxide. For samples treated with HF, four spectral components are needed to fit the Ge 3d photoemission spectra. One is the bulk component and the other three are attributed to the surface Ge atoms with mono-hydride, di-hydride and tri-hydride terminations, respectively

  17. Structural and functional organization of the HF.10 human zinc finger gene (ZNF35) located on chromosome 3p21-p22

    DEFF Research Database (Denmark)

    Lanfrancone, L; Pengue, G; Pandolfi, P P

    1992-01-01

    We report the structural and functional characterization of the HF.10 zinc finger gene (ZNF35) in normal human cells, as well as a processed pseudogene. The HF.10 gene spans about 13 kb and it is interrupted by three introns. All 11 zinc finger DNA-binding domains are contiguously encoded within...... and partial nucleotide sequencing of the HF.10 pseudogene indicated that it has arisen by retroposition of spliced HF.10 mRNA. In situ hybridization experiments revealed that both the functional locus and the pseudogene map to chromosome 3p21p22, a region that is frequently deleted in small cell lung...... and renal carcinomas. Hybridization of the HF.10 gene and the HF.10 pseudogene DNA probes to metaphases from a small cell lung carcinoma cell line with the 3p deletion revealed that both loci are part of the deleted chromosome region....

  18. QAPP for Hydraulic Fracturing (HF) Surface Spills Data Analysis

    Science.gov (United States)

    This QAPP provides information concerning the analysis of spills associated with hydraulic fracturing. This project is relevant to both the chemical mixing and flowback and produced water stages of the HF water cycle as found in the HF Study Plan.

  19. SEMICONDUCTOR TECHNOLOGY: Wet etching characteristics of a HfSiON high-k dielectric in HF-based solutions

    Science.gov (United States)

    Yongliang, Li; Qiuxia, Xu

    2010-03-01

    The wet etching properties of a HfSiON high-k dielectric in HF-based solutions are investigated. HF-based solutions are the most promising wet chemistries for the removal of HfSiON, and etch selectivity of HF-based solutions can be improved by the addition of an acid and/or an alcohol to the HF solution. Due to densification during annealing, the etch rate of HfSiON annealed at 900 °C for 30 s is significantly reduced compared with as-deposited HfSiON in HF-based solutions. After the HfSiON film has been completely removed by HF-based solutions, it is not possible to etch the interfacial layer and the etched surface does not have a hydrophobic nature, since N diffuses to the interface layer or Si substrate formation of Si-N bonds that dissolves very slowly in HF-based solutions. Existing Si-N bonds at the interface between the new high-k dielectric deposit and the Si substrate may degrade the carrier mobility due to Coulomb scattering. In addition, we show that N2 plasma treatment before wet etching is not very effective in increasing the wet etch rate for a thin HfSiON film in our case.

  20. Wet etching characteristics of a HfSiON high-k dielectric in HF-based solutions

    International Nuclear Information System (INIS)

    Li Yongliang; Xu Qiuxia

    2010-01-01

    The wet etching properties of a HfSiON high-k dielectric in HF-based solutions are investigated. HF-based solutions are the most promising wet chemistries for the removal of HfSiON, and etch selectivity of HF-based solutions can be improved by the addition of an acid and/or an alcohol to the HF solution. Due to densification during annealing, the etch rate of HfSiON annealed at 900 0 C for 30 s is significantly reduced compared with as-deposited HfSiON in HF-based solutions. After the HfSiON film has been completely removed by HF-based solutions, it is not possible to etch the interfacial layer and the etched surface does not have a hydrophobic nature, since N diffuses to the interface layer or Si substrate formation of Si-N bonds that dissolves very slowly in HF-based solutions. Existing Si-N bonds at the interface between the new high-k dielectric deposit and the Si substrate may degrade the carrier mobility due to Coulomb scattering. In addition, we show that N 2 plasma treatment before wet etching is not very effective in increasing the wet etch rate for a thin HfSiON film in our case. (semiconductor technology)

  1. HfO2 as gate dielectric on Ge: Interfaces and deposition techniques

    International Nuclear Information System (INIS)

    Caymax, M.; Van Elshocht, S.; Houssa, M.; Delabie, A.; Conard, T.; Meuris, M.; Heyns, M.M.; Dimoulas, A.; Spiga, S.; Fanciulli, M.; Seo, J.W.; Goncharova, L.V.

    2006-01-01

    To fabricate MOS gate stacks on Ge, one can choose from a multitude of metal oxides as dielectric material which can be deposited by many chemical or physical vapor deposition techniques. As a few typical examples, we will discuss here the results from atomic layer deposition (ALD), metal organic CVD (MOCVD) and molecular beam deposition (MBD) using HfO 2 /Ge as materials model system. It appears that a completely interface layer free HfO 2 /Ge combination can be made in MBD, but this results in very bad capacitors. The same bad result we find if HfGe y (Hf germanides) are formed like in the case of MOCVD on HF-dipped Ge. A GeO x interfacial layer appears to be indispensable (if no other passivating materials are applied), but the composition of this interfacial layer (as determined by XPS, TOFSIMS and MEIS) is determining for the C/V quality. On the other hand, the presence of Ge in the HfO 2 layer is not the most important factor that can be responsible for poor C/V, although it can still induce bumps in C/V curves, especially in the form of germanates (Hf-O-Ge). We find that most of these interfacial GeO x layers are in fact sub-oxides, and that this could be (part of) the explanation for the high interfacial state densities. In conclusion, we find that the Ge surface preparation is determining for the gate stack quality, but it needs to be adapted to the specific deposition technique

  2. Hf layer thickness dependence of resistive switching characteristics of Ti/Hf/HfO2/Au resistive random access memory device

    Science.gov (United States)

    Nakajima, Ryo; Azuma, Atsushi; Yoshida, Hayato; Shimizu, Tomohiro; Ito, Takeshi; Shingubara, Shoso

    2018-06-01

    Resistive random access memory (ReRAM) devices with a HfO2 dielectric layer have been studied extensively owing to the good reproducibility of their SET/RESET switching properties. Furthermore, it was reported that a thin Hf layer next to a HfO2 layer stabilized switching properties because of the oxygen scavenging effect. In this work, we studied the Hf thickness dependence of the resistance switching characteristics of a Ti/Hf/HfO2/Au ReRAM device. It is found that the optimum Hf thickness is approximately 10 nm to obtain good reproducibility of SET/RESET voltages with a small RESET current. However, when the Hf thickness was very small (∼2 nm), the device failed after the first RESET process owing to the very large RESET current. In the case of a very thick Hf layer (∼20 nm), RESET did not occur owing to the formation of a leaky dielectric layer. We observed the occurrence of multiple resistance states in the RESET process of the device with a Hf thickness of 10 nm by increasing the RESET voltage stepwise.

  3. Preparation of HfC single crystals by a floating zone technique

    International Nuclear Information System (INIS)

    Otani, S.; Tanaka, T.

    1981-01-01

    HfC single crystals have been prepared using a floating zone technique by controlling the compositions of the initial molten zone and the feed rod. The obtained crystal rods were 6 cm long and 0.9 cm in diameter. The various parts of the crystal rods have nearly constant compositions (C/Hf(ZR) = 0.956-0.977), and do not contain any free carbon. The impurities in the crystal, evaporation product, and starting material were examined by fluorescence X-ray spectroscopy. The refining effect due to evaporation was discussed. (orig.)

  4. Comparison of HfCl4, HfI4, TEMA-Hf, and TDMA-Hf as precursors in early growing stages of HfO2 films deposited by ALD: A DFT study

    International Nuclear Information System (INIS)

    Cortez-Valadez, M.; Fierro, C.; Farias-Mancilla, J.R.; Vargas-Ortiz, A.; Flores-Acosta, M.; Ramírez-Bon, R.; Enriquez-Carrejo, J.L.

    2016-01-01

    Highlights: • Hafnium oxide growth on Si(100) by atomic layer deposition was simulated. • The interface structure was considered as silicate and silicide. • The interface was studied employing DFT. • TDMA-Hf precursor show better interface stability. - Abstract: The final structure of HfO 2 films grown by atomic layer deposition (ALD) after reaction with OH − ions has been analyzed by DFT (density functional theory). The interaction of the precursors: HfCl 4 (hafnium tetrachloride), HfI 4 (hafnium tetraiodide), TEMA-Hf (tetrakis-ethylmethylamino hafnium), and TDMA-Hf (tetrakis-dimethylamino hafnium) with HO–H was studied employing the B3LYP (Becke 3-parameter, Lee–Yang–Parr) hybrid functional and the PBE (Perdew–Burke–Ernzerhof) generalized gradient functional. The structural evolution at the Si(100) surface has been analyzed by LDA (local density approximation). The structural parameters: bond length and bond angle, and the vibrational parameters for the optimized structures are also reported. The presence of hafnium silicate at the interface was detected. The infrared spectra and structural parameters obtained in this work agree with previously reported experimental results.

  5. Comparison of HfCl{sub 4}, HfI{sub 4}, TEMA-Hf, and TDMA-Hf as precursors in early growing stages of HfO{sub 2} films deposited by ALD: A DFT study

    Energy Technology Data Exchange (ETDEWEB)

    Cortez-Valadez, M. [Departamento de Investigación en Física, Universidad de Sonora, Apdo. Postal 5-88, 83190 Hermosillo, Son. (Mexico); Fierro, C.; Farias-Mancilla, J.R. [Instituto de Ingeniería y Tecnología, Departamento de Física y Matemáticas, Universidad Autónoma de Ciudad Juárez, Av. del Charro 450, Cd. Juárez C.P. 32310, Chihuahua (Mexico); Vargas-Ortiz, A. [Universidad Autónoma de Sinaloa, Facultad de Ingeniería Mochis, Ciudad Universitaria, C.P. 81223 Los Mochis, Sinaloa (Mexico); Flores-Acosta, M. [Departamento de Investigación en Física, Universidad de Sonora, Apdo. Postal 5-88, 83190 Hermosillo, Son. (Mexico); Ramírez-Bon, R. [Centro de Investigación y Estudios Avanzados del IPN, Unidad Querétaro, Apdo. Postal 1-798, 76001 Querétaro, Qro. (Mexico); Enriquez-Carrejo, J.L. [Instituto de Ingeniería y Tecnología, Departamento de Física y Matemáticas, Universidad Autónoma de Ciudad Juárez, Av. del Charro 450, Cd. Juárez C.P. 32310, Chihuahua (Mexico); and others

    2016-06-15

    Highlights: • Hafnium oxide growth on Si(100) by atomic layer deposition was simulated. • The interface structure was considered as silicate and silicide. • The interface was studied employing DFT. • TDMA-Hf precursor show better interface stability. - Abstract: The final structure of HfO{sub 2} films grown by atomic layer deposition (ALD) after reaction with OH{sup −} ions has been analyzed by DFT (density functional theory). The interaction of the precursors: HfCl{sub 4} (hafnium tetrachloride), HfI{sub 4} (hafnium tetraiodide), TEMA-Hf (tetrakis-ethylmethylamino hafnium), and TDMA-Hf (tetrakis-dimethylamino hafnium) with HO–H was studied employing the B3LYP (Becke 3-parameter, Lee–Yang–Parr) hybrid functional and the PBE (Perdew–Burke–Ernzerhof) generalized gradient functional. The structural evolution at the Si(100) surface has been analyzed by LDA (local density approximation). The structural parameters: bond length and bond angle, and the vibrational parameters for the optimized structures are also reported. The presence of hafnium silicate at the interface was detected. The infrared spectra and structural parameters obtained in this work agree with previously reported experimental results.

  6. Transitions of bandgap and built-in stress for sputtered HfZnO thin films after thermal treatments

    Energy Technology Data Exchange (ETDEWEB)

    Li, Chih-Hung; Chen, Jian-Zhang [Institute of Applied Mechanics, National Taiwan University, Taipei City 10617, Taiwan (China); Cheng, I-Chun [Graduate Institute of Photonics and Optoelectronics and Department of Electrical Engineering, National Taiwan University, Taipei City 10617, Taiwan (China)

    2013-08-28

    HfZnO thin films with various Hf contents are sputter-deposited on glass substrates from Hf{sub x}Zn{sub 1−x}O (x = 0, 2.5, 5, 7.5, and 10 at. %) targets at room temperature. The incorporation of Hf in the ZnO film leads to the amorphorization of the materials. The amorphous structures of high-Hf-content films remain after annealing at 600 °C for 30 min. The built-in stresses of as-deposited films are compressive. As the annealing temperature increases, the stresses are relaxed and even become tensile. The films exhibit a high transmission of 80% in the visible region. The optical bandgap increases with the Hf content, but it decreases with the annealing temperature. This can be attributed to the alteration of strain (stress) status in the films and atomic substitution. The reduction of bandgap partly results from the grain growth, which is due to the quantum confinement effect of the small grains. Hf doping increases the resistivity of ZnO owing to the disorder of the material structure and the higher bandgap, which result in more carrier traps and less thermally excited carriers in the conduction bands.

  7. Deep electron traps in HfO_2-based metal-oxide-semiconductor capacitors

    International Nuclear Information System (INIS)

    Salomone, L. Sambuco; Lipovetzky, J.; Carbonetto, S.H.; García Inza, M.A.; Redin, E.G.; Campabadal, F.

    2016-01-01

    Hafnium oxide (HfO_2) is currently considered to be a good candidate to take part as a component in charge-trapping nonvolatile memories. In this work, the electric field and time dependences of the electron trapping/detrapping processes are studied through a constant capacitance voltage transient technique on metal-oxide-semiconductor capacitors with atomic layer deposited HfO_2 as insulating layer. A tunneling-based model is proposed to reproduce the experimental results, obtaining fair agreement between experiments and simulations. From the fitting procedure, a band of defects is identified, located in the first 1.7 nm from the Si/HfO_2 interface at an energy level E_t = 1.59 eV below the HfO_2 conduction band edge with density N_t = 1.36 × 10"1"9 cm"−"3. A simplified analytical version of the model is proposed in order to ease the fitting procedure for the low applied voltage case considered in this work. - Highlights: • We characterized deep electron trapping/detrapping in HfO_2 structures. • We modeled the experimental results through a tunneling-based model. • We obtained an electron trap energy level of 1.59 eV below conduction band edge. • We obtained a spatial trap distribution extending 1.7 nm within the insulator. • A simplified tunneling front model is able to reproduce the experimental results.

  8. Self-diffusion of Er and Hf inpure and HfO2-doped polycrystalline Er2O3

    International Nuclear Information System (INIS)

    Scheidecker, R.W.

    1979-01-01

    Using a tracer technique, self-diffusion of Er and Hf was measured over the approximate temperature interval of 1600 to 1970 0 C in pure and HfO 2 -doped polycryatalline Er 2 O 3 . Up to about 10 m/o HfO 2 dopant level, the Er self-diffusion coefficients followed a relationship based on cation vacancies. Above 10 m/o HfO 2 , deviation from this relationship occurred, apparently due to clustering of cation vacancies and oxygen interstitials around the dopant hafnia ion. The activation energy for the self-diffusion of Er in pure Er 2 O 3 was 82.2 Kcal/mole and increased with the HfO 2 dopant level present. Self-diffusion of Hf was measured in pure Er 2 O 3 having two impurity levels, and a separation of the grain boundary. The volume diffusion of Hf showed both extrinsic and intrinsic behavior with the transition temperature increasing with the impurity level present in Er 2 O 3 . The activation energy for Hf volume diffusion in the intrinsic region was high, i.e. 235 -+ 9.5 Kcal/mole. The grain boundary diffusion was apparently extrinsic over the entire temperature interval Very low Hf self diffusion rates were found in both pure and HfO 2 doped Er 2 O 3 compositions. Despite a clustering effect, the HfO 2 dopant increased the Hf volume diffusion coefficients

  9. Phase1 upgrade of the CMS-HF Calorimeter

    CERN Document Server

    Gulmez, Erhan

    2016-01-01

    In this presentation, results of the Phase I upgrade of the CMS Hadron Forward Calorimeter (HF) are discussed. The CMS-HF Calorimeter was using regular PMTs. Cherenkov light produced in the quartz fibers embedded in the iron absorber was read out with the PMTs. However, occasionally, stray muons hitting the PMT windows cause Cherenkov radiation in the PMT itself and produce large signals. These large signals mimic a very high-energy particle and are tagged as important by the trigger. To reduce this problem, PMTs had to be replaced. The four-anode PMTs that were chosen have thinner windows; thereby reducing the Cherenkov radiation in the PMT window. As part of the upgrade, the read-out electronics is to be replaced so that the PMTs are read out in two channels by connecting each pair of anodes to a single channel. Information provided by these two channels will help us reject the false signals due to the stray muons since the Cherenkov radiation in the PMT window is more likely to produce a signal only in one...

  10. High resolution TDPAC measurements on 181Ta in Hf2Fe, Hf2Co and Hf2Rh at high temperature

    International Nuclear Information System (INIS)

    Cekic, B.; Koicki, S.; Ivanovic, N.; Manasijevic, M.; Koteski, V.; Marjanovic, D.

    1998-01-01

    The time differential perturbed angular correlation measurements (TDPAC-method ) on 181 Ta ion probe in Hf 2 Co, Hf 2 Fe and Hf 2 Rh intermetallic compounds have been performed at 1170 K, using a fast - slow time spectrometer consisting of two BaF 2 detectors. The results of the measurements show the presence of two independent electric quadrupole interactions, compatible with the crystalline structure of these polycrystalline compounds. (authors)

  11. Magnetic properties of Hf177 and Hf180 in the strong-coupling deformed model

    Science.gov (United States)

    Muto, S.; Stone, N. J.; Bingham, C. R.; Stone, J. R.; Walker, P. M.; Audi, G.; Gaulard, C.; Köster, U.; Nikolov, J.; Nishimura, K.; Ohtsubo, T.; Podolyak, Z.; Risegari, L.; Simpson, G. S.; Veskovic, M.; Walters, W. B.

    2014-04-01

    This paper reports NMR measurements of the magnetic dipole moments of two high-K isomers, the 37/2-, 51.4 m, 2740 keV state in Hf177 and the 8-, 5.5 h, 1142 keV state in Hf180 by the method of on-line nuclear orientation. Also included are results on the angular distributions of γ transitions in the decay of the Hf177 isotope. These yield high precision E2/M1 multipole mixing ratios for transitions in bands built on the 23/2+, 1.1 s, isomer at 1315 keV and on the 9/2+, 0.663 ns, isomer at 321 keV. The new results are discussed in the light of the recently reported finding of systematic dependence of the behavior of the gR parameter upon the quasiproton and quasineutron make up of high-K isomeric states in this region.

  12. Electric Field Gradients at Hf and Fe Sites in Hf2Fe Recalculated

    International Nuclear Information System (INIS)

    Belosevic-Cavor, J.; Cekic, B.; Novakovic, N.; Koteski, V.; Milosevic, Z.

    2004-01-01

    The electric field gradients (EFG) of the Hf 2 Fe intermetallic compound were calculated using the full-potential linearized augmented plain-wave (FP-LAPW) method as embodied in the WIEN 97 code. The obtained values are compared with other ab-initio calculations and on a qualitative basis with the previously reported experimental data obtained from TDPAC. The calculated results, -23.1.10 21 V/m 2 and 2.7.10 21 V/m 2 for Hf 48f and Fe 32e position, respectively, are in excellent agreement with experimental data (23.4.10 21 V/m 2 and 2.7.10 21 V/m 2 ), better than those reported in earlier calculations. The calculated EFG for Hf 16c position (4.2.10 21 V/m 2 ) is stronger than the experimental one (1.1.10 21 V/m 2 ).

  13. Lifetime of the first excited 2{sup +} state in {sup 172}Hf and {sup 174}Hf

    Energy Technology Data Exchange (ETDEWEB)

    Gerst, Rosa-Belle; Stegemann, Simon; Jolie, Jan; Regis, Jean-Marc; Rudigier, Matthias; Saed-Samii, Nima; Zell, Karl Oskar [Institut fuer Kernphysik, Universitaet zu Koeln, Zuelpicher Str. 77, 50937 Koeln (Germany)

    2014-07-01

    Using the {sup 170}Yb(α,2n) and {sup 172}Yb(α,2n) reactions the lifetimes of the first excited 2{sup +} state in {sup 172}Hf and {sup 174}Hf have been measured in fast-timing experiments using the Cologne Orange-Spectrometer and 6 LaBr{sub 3}(Ce)-Detectors. The lifetimes were obtained analyzing e{sup -}-γ-coincidence time-spectra with the slope method. The new and more precise lifetimes correct existing, outdated lifetimes in nuclear databases. Additionally, the systematics of the B(E2,2{sub 1}{sup +}→0{sub 1}{sup +}) is studied.

  14. Search for chemical separations of the element 106 homologues in HF and HF-HCl media

    International Nuclear Information System (INIS)

    Trubert, D.; Monroy-Guzman, F.; Hussonnois, M.; Brillard, L.; Le Naour, C.; Constantinescu, O.

    1996-01-01

    In order to study the chemical properties of element 263 106 in aqueous media, fast, efficient and reproducible chromatographic separations were tested on its assumed homologous: Mo, W and U. Corroborative static and dynamic off-line experiments have shown that after fixation of these three elements on anion-exchange resin in HF medium, selective elution could be achieved by using suitable concentration of HCl - HF and HCl solutions. Separations of short-lived W isotopes, produced through heavy ion irradiation were also performed on-line. (author). 27 refs., 14 figs

  15. Digital hf radar observations of equatorial spread-F

    International Nuclear Information System (INIS)

    Argo, P.E.

    1984-01-01

    Modern digital ionosondes, with both direction finding and doppler capabilities can provide large scale pictures of the Spread-F irregularity regions. A morphological framework has been developed that allows interpretation of the hf radar data. A large scale irregularity structure is found to be nightward of the dusk terminator, stationary in the solar reference frame. As the plasma moves through this foehn-wall-like structure it descends, and irregularities may be generated. Localized upwellings, or bubbles, may be produced, and they drift with the background plasma. The spread-F irregularity region is found to be best characterized as a partly cloudy sky, due to the patchiness of the substructures. 13 references, 16 figures

  16. Elemental content in ground and soluble/instant coffee

    International Nuclear Information System (INIS)

    Vega-Carrillo, H.R.; Manzanares-Acuna, E.; Iskander, F.Y.

    2002-01-01

    The concentration of thirty-four elements in twelve coffee brands has been measured using instrumental neutron activation analysis. The samples investigated included four brands of commercially available ground coffee and eight brands of soluble/instant coffee. The elements measured were Al, As, Ba, Ca, Ce, Co, Cr, Cs, Dy, Eu, Fe, Gd, Hf, K, La, Lu, Mg, Mn, Na, Rb, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, Ti, Tm, U, V, Yb and Zn. Twenty four elements were found to be below the detection limit in one or more samples. These elements were Ce, Cr, Fe, V, As, Eu, Ba, Dy, Gd, Hf, La, Lu, Sb, Sc, Se, Sm, Sr, Ta, Tb, Th, Ti, Yb, Tm, and U. (author)

  17. HF Radio Astronomy from a Small Satellite

    Science.gov (United States)

    2016-06-15

    SSC16-XI-03 HF Radio Astronomy from a Small Satellite Frank C. Robey1, Mary Knapp2, Alan J. Fenn1, Mark Silver1, Kerry Johnson1 Frank J. Lind3...frequency end of the electromagnetic spectrum (below 15 MHz) is one of the least explored windows in observational astronomy . Observations at these...pdf. [Accessed: 17-Oct-2015]. 3. G. Hallinan, “The Owens Valley LWA,” in Exascale Radio Astronomy , 2014, vol. 2. 4. C. J. Lonsdale, R. J. Cappallo

  18. High-aspect-ratio HfC nanobelts accompanied by HfC nanowires: Synthesis, characterization and field emission properties

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Song, E-mail: tiansong22@126.com [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072 (China); School of Materials Science and Engineering, Chongqing Jiaotong University, Chongqing 400074 (China); Zhang, Yulei; Ren, Jincui; Qiang, Xinfa; Zhang, Shouyang [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072 (China); Li, Hejun, E-mail: lihejun@nwpu.edu.cn [State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi’an 710072 (China)

    2017-04-30

    Highlights: • HfC naobelts accompanied by HfC nanowires were synthesized by a catalytic CVD method. • HfC nanobelts as a novel structure of HfC ceramic are reported for the first time. • HfC nanobelts have 100–200 μm in lengths and reach up to 10 μm in widths. • The synthesized product is promising field nanoemitters. - Abstract: As a key refractory carbide, hafnium carbide (HfC) is commonly used as structural materials while the field emission (FE) application of HfC in the field of vacuum microelectronics is almost the only one for functional material purposes. Based on its outstanding physical and chemical characteristics, HfC is identified as a potential candidate with satisfactory mechanical properties and long-term and/or high-temperature FE stability for future applications in high-performance field emitters. However, the development of HfC in various FE applications is hindered because it is not facile to fabricate large-scale low-dimensional HfC field nanoemitters. Herein, High-aspect-ratio HfC nanobelts accompanied by HfC nanowires were synthesized on a large scale by a traditional and simple catalytic chemical vapor deposition (CVD) method. Classical vapor–liquid–solid (VLS) theory was employed to explain the growth of the HfC nanowires and nanobelts along axial direction. The thin HfO{sub 2} shell and thin C layer surrounding the nanostructures might give rise to the diameter fluctuation of HfC nanowires and the width increase of HfC nanobelts in lateral direction. Field emission results show that the high-aspect-ratio HfC nanobelts accompanied by the nanowires are promising field nanoemitters, which exhibit excellent field emission properties with a fairly low turn-on field of ∼1.5 V μm{sup −1} and a low current fluctuation less than ∼10%. This suggests that HfC ceramics with high-aspect-ratio nanostructures are ideal cathode material for various field emission applications.

  19. Ab initio theoretical study of dipole-bound anions of molecular complexes: (HF)3- and (HF)4- anions

    Science.gov (United States)

    Ramaekers, Riet; Smith, Dayle M. A.; Smets, Johan; Adamowicz, Ludwik

    1997-12-01

    Ab initio calculations have been performed to determine structures and vertical electron detachment energy (VDE) of the hydrogen fluoride trimer and tetramer anions, (HF)3- and (HF)4-. In these systems the excess electron is bound by the dipole field of the complex. It was determined that, unlike the neutral complexes which prefer the cyclic structures, the equilibrium geometries of the anions have "zig-zag" shapes. For both complexes the predicted VDEs are positive [210 meV and 363 meV for (HF)3- and (HF)4-, respectively], indicating that the anions are stable systems with respect to the vertical electron detachment. These results were obtained at the coupled-cluster level of theory with single, double and triple excitations [CCSD(T) method; the triple-excitation contribution in this method is calculated approximately using the perturbation approach] with the anion geometries obtained using the second-order Møller-Plesset perturbation theory (MP2) method. The same approach was also used to determine the adiabatic electron affinities (AEA) of (HF)3 and (HF)4. In addition to the electronic contribution, we also calculated the contributions (using the harmonic approximation) resulting from different zero-point vibration energies of the neutral and anionic clusters. The calculations predicted that while the AEA of (HF)3 is positive (44 meV), the AEA for (HF)4 is marginally negative (-16 meV). This suggests that the (HF)3- anion should be a stable system, while the (HF)4- is probably metastable.

  20. Thermoelectric properties of doped BaHfO_3

    International Nuclear Information System (INIS)

    Dixit, Chandra Kr.; Bhamu, K. C.; Sharma, Ramesh

    2016-01-01

    We have studied the structural stability, electronic structure, optical properties and thermoelectric properties of doped BaHfO_3 by full potential linearized augmented plane wave (FP-LAPW) method. The electronic structure of BaHfO_3 doped with Sr shows enhances the indirect band gaps of 3.53 eV, 3.58 eV. The charge density plots show strong ionic bonding in Ba-Hf, and ionic and covalent bonding between Hf and O. Calculations of the optical spectra, viz., the dielectric function, refractive index and extinction coefficient are performed for the energy range are calculated and analyzed. Thermoelectric properties of semi conducting are also reported first time. The doped BaHfO_3 is approximately wide band gap semiconductor with the large p-type Seebeck coefficient. The power factor of BaHfO_3 is increased with Sr doping, decreases because of low electrical resistivity and thermal conductivity.

  1. Nuclear quadrupole interactions in ferroelectric compounds of HF181

    International Nuclear Information System (INIS)

    Kunzler, J.V.

    1971-01-01

    Measurements of nuclear quadrupole interaction constants in perovkite-type compounds of PbHfO 3 , SnhfO 3 , CaHfO 3 e SrHfO 3 have been performed using the perturbed angular correlation technique. A range of fundamental frequencies from 150 to 550 Megaradians persecond was determined. The variation of quadrupole constants has been discussed through the molecular orbital theory

  2. Application of HF Radar in Hazard Management

    Directory of Open Access Journals (Sweden)

    Mal Heron

    2016-01-01

    Full Text Available A review is given of the impact that HF radars are having on the management of coastal hazards. Maps of surface currents can be produced every 10–20 minutes which, in real time, improve navigation safety in restricted areas commonly found near ports and harbours. The time sequence of surface current maps enables Lagrangian tracking of small parcels of surface water, which enables hazard mitigation in managing suspended sediments in dredging, in emergency situations where flotsam and other drifting items need to be found, and in pollution control. The surface current measurement capability is used to assist tsunami warnings as shown by the phased-array data from Chile following the Great Tohoku Earthquake in 2011. The newly launched Tsunami Warning Center in Oman includes a network of phased-array HF radars to provide real-time tsunami monitoring. Wind direction maps can be used to locate the position of cold fronts in the open ocean and to monitor the timing and strength of sea-breeze fronts in key locations.

  3. Beta decomposition processes in Hf-rich Hf--Nb alloys

    International Nuclear Information System (INIS)

    Jones, W.B.; Taggart, R.; Polonis, D.H.

    1978-01-01

    The decomposition of the bcc β-phase by both athermal and isothermal processes has been investigated in Hf-rich Hf--Nb alloys. An all β-phase structure is retained in chill-cast alloys containing 30 to 50 at.% Nb (Cb), although electron diffraction streaking effects and the behavior of the temperature coefficient of electrical resistivity indicate the presence of a bcc lattice instability similar to that reported in solute lean Ti and Zr alloys. Aging a Hf 0 . 65 Nb 0 . 35 alloy at 400 and 600 0 C resulted in the direct precipitation of a fine dispersion of α-phase needles; this morphology differs from the discs of transition α (α/sub t/) which Carpenter et al observed in Nb-rich Nb 0 . 68 Hf 0 . 32 . During continued aging, the needles grow selectively to form colonies or groups of needles in which both the individual needles and the groups of needles have major axes aligned along (110)/sub β/ type directions. The initial α-phase particles exhibit the Burgers orientation relationship with the parent matrix; continued aging changes the electron diffraction patterns in a way that is similar to that observed in aged Ti--Mo and Ti--Mo--Al alloys where they were attributed to the α-phase having a different crystallographic relationship to the β-phase (Type 2 α-phase). The observed changes in the electron diffraction patterns of aged Hf 0 . 65 Nb 0 . 35 cannot be described as resulting from strained Burgers α-phase

  4. Hf isotope evidence for a hidden mantle reservoir

    DEFF Research Database (Denmark)

    Bizzarro, Martin; Simonetti, A.; Stevenson, R.K.

    2002-01-01

    High-precision Hf isotopic analyses and U-Pb ages of carbonatites and kimberlites from Greenland and eastern North America, including Earth's oldest known carbonatite (3 Ga), indicate derivation from an enriched mantle source. This previously unidentified mantle reservoir-marked by an unradiogenic...... Hf isotopic composition and preserved in the deep mantle for at least 3 b.y.-may account for the mass imbalance in Earth's Hf-Nd budget. The Hf isotopic data presented here support a common mantle source region and genetic link between carbonatite and some oceanic-island basalt volcanoes....

  5. Microstructural characterization of as-cast hf-b alloys

    Directory of Open Access Journals (Sweden)

    João Carlos Jânio Gigolotti

    2012-04-01

    Full Text Available An accurate knowledge of several metal-boron phase diagrams is important to evaluation of higher order systems such as metal-silicon-boron ternaries. The refinement and reassessment of phase diagram data is a continuous work, thus the reevaluation of metal-boron systems provides the possibility to confirm previous data from an investigation using higher purity materials and better analytical techniques. This work presents results of rigorous microstructural characterization of as-cast hafnium-boron alloys which are significant to assess the liquid composition associated to most of the invariant reactions of this system. Alloys were prepared by arc melting high purity hafnium (minimum 99.8% and boron (minimum 99.5% slices under argon atmosphere in water-cooled copper crucible with non consumable tungsten electrode and titanium getter. The phases were identified by scanning electron microscopy, using back-scattered electron image mode and X-ray diffraction. In general, a good agreement was found between our data and those from the currently accepted Hafnium-Boron phase diagram. The phases identified are αHfSS and B-RhomSS, the intermediate compounds HfB and HfB2 and the liquide L. The reactions are the eutectic L ⇔ αHfSS + HfB and L ⇔ HfB2 + B-Rhom, the peritectic L + HfB2 ⇔ HfB and the congruent formation of HfB2.

  6. PEMISAHAN Zr – Hf SECARA SINAMBUNG MENGGUNAKAN MIXER SETTLER

    Directory of Open Access Journals (Sweden)

    Dwi Biyantoro

    2017-01-01

    Full Text Available ABSTRAK PEMISAHAN Zr – Hf SECARA SINAMBUNG MENGGUNAKANMIXER SETTLER. Telah dilakukan pemisahanZr – Hf secara sinambung menggunakan pengaduk pengenap (mixer settler 16 stage. Larutan umpan adalah zirkon nitrat dengan kadar Zr = 30786 ppm dan Hf = 499 ppm. Ekstraktan dipakai adalah solven 60 % TBP dalam kerosen dan larutan scrubbingyang dipakai adalah asam nitrat 1 M. Umpan masuk pada stageke 5 dikontakkan secara berlawanan arah dengan solven masuk pada stage ke 16 dan larutan scrubbing masuk pada stage ke 1. Tujuan penelitian ini adalah memisahkan unsur Zr dan Hf dari hasil olah pasir zirkon menggunakan solven TBP dengan alat mixer settler16 stage. Analisis umpan dan hasil proses pemisahan untuk zirkonium (Zr dilakukan dengan menggunakan alat pendar sinar-X, sedangkananalisis unsur hafnium (Hf menggunakan Analisis Pengaktifan Neutron (APN. Parameter penelitian dilakukan dengan variasi keasaman asam nitrat dalam umpan dan variasi waktu pada berbagai laju pengadukan. Hasil penelitian pemisahan unsur Zr dengan Hf diperolehkondisi optimum pada keasaman umpan 4 N HNO3, keseimbangan dicapai setelah 3jam dan laju pengadukan 3300 rpm. Hasil ekstrak  unsur zirkon (Zr diperoleh kadar sebesar 28577 ppm dengan efisiensi 92,76 % serta kadar pengotor hafnium (Hf sebesar 95 ppm. Kata Kunci: pemisahan Zr, Hf, ekstraksi, mixer settler, alat pendar sinar-X, APN. ABSTRACT SEPARATION of Zr - Hf CONTINUOUSLY USE THE MIXER SETTLER. Separation of Zr - Hf continuously using mixer settler 16 stage has been done. The feed solution is zircon nitrate concentration of Zr = 30786 ppm  and Hf = 499 ppm. As the solvent used extractant 60 % TBP in 40 % kerosene. Nitric acid solution used srubbing 1 M. The feed entered into stage to 5 is contacted with solvents direction on the stage to 16 and the scrubbing solution enter the stage to 1. The purpose of this study is to separate Zr and Hf of the results from the process of zircon sand using solvent TBP using 16 stage

  7. High-temperature x-ray diffraction study of HfTiO4-HfO2 solid solutions

    International Nuclear Information System (INIS)

    Carpenter, D.A.

    1975-01-01

    High-temperature x-ray diffraction techniques were used to determine the axial thermal expansion curves of HfTiO 4 -HfO 2 solid solutions as a function of composition. Data show increasing anisotropy with increasing HfO 2 content. An orthorhombic-to-monoclinic phase transformation was detected near room temperature for compositions near the high HfO 2 end of the orthorhombic phase field and for compositions within the two-phase region (HfTiO 4 solid solution plus HfO 2 solid solution). An orthorhombic-to-cubic phase transformation is indicated by data from oxygen-deficient materials at greater than 1873 0 K. (U.S.)

  8. Simultaneous analysis of rotational and vibrational-rotational spectra of DF and HF to obtain irreducible molecular constants for HF

    International Nuclear Information System (INIS)

    Horiai, Koui; Uehara, Hiromichi

    2011-01-01

    Graphical abstract: Available rotational and vibrational-rotational spectral lines of DF and HF are analyzed simultaneously using a non-Born-Oppenheimer effective Hamiltonian. Research highlights: → Simultaneous analysis of DF and HF spectral data. → Application of a non-Born-Oppenheimer effective Hamiltonian. → Twenty irreducible molecular constants for HF have been determined. - Abstract: Analytic expressions of corrections for the breakdown of the Born-Oppenheimer approximation to Dunham's Y ij with optimal parameters, i.e., determinable clusters of expansion coefficients, are applied to a data analysis of the rotational and vibrational-rotational transitions of HF reported in the literature. All the available spectral lines of the two isotopologues, DF and HF, are simultaneously fitted to a single set of molecular parameters of HF within experimental errors. Fitting of a data set of 595 spectral transitions for DF and HF has generated only 20 minimal independent parameter values, i.e., 'irreducible' molecular constants of HF, that are sufficient to precisely generate 82 Y ij coefficients and 144 band constants in total: 41 Y ij and 72 band constants each for DF and HF.

  9. Characterization of Hf/Mg co-doped ZnO thin films after thermal treatments

    Energy Technology Data Exchange (ETDEWEB)

    Li, Chih-Hung; Chung, Hantsun [Graduate Institute of Applied Mechanics, National Taiwan University, Taipei 10617, Taiwan (China); Chen, Jian-Zhang, E-mail: jchen@ntu.edu.tw [Graduate Institute of Applied Mechanics, National Taiwan University, Taipei 10617, Taiwan (China); Cheng, I-Chun, E-mail: iccheng@ntu.edu.tw [Graduate Institute of Photonics and Optoelectronics, Department of Electrical Engineering, National Taiwan University, Taipei 10617, Taiwan (China)

    2014-11-03

    Rf-sputtered Mg{sub 0.05}Zn{sub 0.95}O thin films become amorphous/nanocrystalline with the addition of hafnium oxide. All films (thickness: ∼ 100 nm) sputter-deposited from Hf{sub x}Mg{sub 0.05}Zn{sub 0.95−x}O targets are highly transparent (> 80%) from 400 to 800 nm. The Tauc bandgap ΔE (eV) increases with the Hf content. However, the bandgap decreases after thermal treatment. The reduction in the bandgap is positively correlated with the Hf content and annealing temperature. The residual stresses of films sputtered from Mg{sub 0.05}Zn{sub 0.95}O and Hf{sub 0.025}Mg{sub 0.05}Zn{sub 0.925}O targets are determined based on X-ray diffraction (XRD) data using a bi-axial stress model. The residual stresses of as-deposited films are compressive. As the annealing temperature increases, the residual stresses are relaxed and even become tensile. The bandgap narrowing after thermal treatment is attributed to the stress relaxation that changes the repulsion between the oxygen 2p and zinc 4s bands. Slight grain growth may also result in bandgap reduction because bandgap modification caused by the quantum confinement effect becomes significant in amorphous/nanocrystalline materials. The amorphous thin films reveal good thermal stability after 600 °C annealing for up to 2 h, as evidenced by the XRD and transmission spectra. - Highlights: • Thin films are sputtered from Hf{sub x}Mg{sub 0.05}Zn{sub 0.95−x}O targets at room temperature. • Bandgap increases with Hf content but decreases with post-annealing temperature. • Bandgap narrowing after annealing partly results from the relaxation of stresses. • Bandgap narrowing partly results from quantum confinement effect by nanomaterials. • Hf doping increases resistivity due to the lattice disorder and enlarged bandgap.

  10. Probes and their application to the study of H.F. plasmoids; Les sondes et leur application dans l'etude des plasmoides H.F

    Energy Technology Data Exchange (ETDEWEB)

    Brunet, A; Geller, R [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

    1960-07-01

    In the first part of this paper, we study the single Langmuir probe and the double-probe method. In the second part, we describe the probe-technique in connection with R.F. plasmoids. (author) [French] Dans la premiere partie de cet article, nous rappelons les principes d'utilisation de la sonde simple de Langmuir ainsi que la methode de la sonde double. La seconde partie est consacree a la pratique des sondes dans l'etude des plasmoides H.F. (auteur)

  11. Soluble CD163

    DEFF Research Database (Denmark)

    Møller, Holger J

    2012-01-01

    CD163 is an endocytic receptor for haptoglobin-hemoglobin complexes and is expressed solely on macrophages and monocytes. As a result of ectodomain shedding, the extracellular portion of CD163 circulates in blood as a soluble protein (sCD163) at 0.7-3.9 mg/l in healthy individuals. The function o...

  12. Direct currents produced by hf heating of plasma

    International Nuclear Information System (INIS)

    Klima, R.

    1974-01-01

    In addition to the well-known diffusion currents, toroidal direct currents arise in h.f. heated plasmas as a result of a momentum transfer from the h.f. field to plasma particles. The estimates of steady-state conditions are given for these currents. Particularly, the possibility of stationary operation of a Tokamak device is analyzed. (author)

  13. Lu-Hf and Sm-Nd garnet geochronology

    DEFF Research Database (Denmark)

    Smit, Matthijs Arjen; Scherer, Erik E.; Mezger, Klaus

    2013-01-01

    To investigate the systematics of the 176Lu–176Hf and 147Sm–143Nd garnet chronometers, we performed REE and isotope analyses on garnet crystals of different size (0.55–3.1 mm radius) from a single granulite specimen (Archean Pikwitonei Granulite Domain, Manitoba, Canada). The Lu–Hf dates are simi...

  14. Investigation of samarium solubility in the magnesium based solid solution

    International Nuclear Information System (INIS)

    Rokhlin, L.L.; Padezhnova, E.M.; Guzej, L.S.

    1976-01-01

    Electric resistance measurements and microscopic analysis were used to investigate the solubility of samarium in a magnesium-based solid solution. The constitutional diagram Mg-Sm on the magnesium side is of an eutectic type with the temperature of the eutectic transformation of 542 deg C. Samarium is partly soluble in solid magnesium, the less so, the lower is the temperature. The maximum solubility of samarium in magnesium (at the eutectic transformation point) is 5.8 % by mass (0.99 at. %). At 200 deg C, the solubility of samarium in magnesium is 0.4 % by mass (0.063 at. %)

  15. Uranyl Oxalate Solubility

    Energy Technology Data Exchange (ETDEWEB)

    Leturcq, G.; Costenoble, S.; Grandjean, S. [CEA Marcoule DEN/DRCP/SCPS/LCA - BP17171 - 30207 Bagnols sur Ceze cedex (France)

    2008-07-01

    The solubility of uranyl oxalate was determined at ambient temperature by precipitation in oxalic-nitric solutions, using an initial uranyl concentration of 0.1 mol/L. Oxalic concentration varied from 0.075 to 0.3 mol/L while nitric concentration ranged between 0.75 and 3 mol/L. Dissolution tests, using complementary oxalic-nitric media, were carried out for 550 hours in order to study the kinetic to reach thermodynamic equilibrium. Similar solubility values were reached by dissolution and precipitation. Using the results, it was possible to draw the solubility surface versus oxalic and nitric concentrations and to determine both the apparent solubility constant of UO{sub 2}C{sub 2}O{sub 4}, 3H{sub 2}O (Ks) and the apparent formation constant of the first uranyl-oxalate complex UO{sub 2}C{sub 2}O{sub 4} (log {beta}1), for ionic strengths varying between 1 and 3 mol/L. Ks and log {beta}1 values were found to vary from 1.9 10{sup -8} to 9.2 10{sup -9} and from 5.95 to 6.06, respectively, when ionic strength varied from 1 to 3 mol/L. A second model may fit our data obtained at an ionic strength of 3 mol/L suggesting as reported by Moskvin et al. (1959) that no complexes are formed for [H{sup +}] at 3 M. The Ks value would then be 1.3 10{sup -8}. (authors)

  16. Argon solubility in liquid steel

    NARCIS (Netherlands)

    Boom, R; Dankert, O; Van Veen, A; Kamperman, AA

    2000-01-01

    Experiments have been performed to establish the solubility of argon in liquid interstitial-free steel. The solubility appears to be lower than 0.1 at ppb, The results are in line with argon solubilities reported in the literature on liquid iron. Semiempirical theories and calculations based on the

  17. Process Simulation Analysis of HF Stripping

    Directory of Open Access Journals (Sweden)

    Thaer A. Abdulla

    2015-02-01

    Full Text Available    HYSYS process simulator is used for the analysis of existing HF stripping column in LAB plant (Arab Detergent Company, Baiji-Iraq. Simulated column performance and profiles curves are constructed. The variables considered are the thermodynamic model option, bottom temperature, feed temperature, and column profiles for the temperature, vapor flow rate, liquid flow rate and composition. The five thermodynamic models options used (Margules, UNIQUAC, van laar, Antoine, and Zudkevitch-Joffee, affecting the results within (0.1-58% variation for the most cases.        The simulated results show that about 4% of paraffin (C10 & C11 presents at the top stream, which may cause a problem in the LAB production plant. The major variations were noticed for the total top vapor flow rate with bottom temperature and with feed composition. The column profiles maintain fairly constants from tray 5 to tray 18. The study gives evidence about a successful simulation with HYSYS because the results correspond with the real plant operation data.

  18. Time variations of hf induced plasma waves

    International Nuclear Information System (INIS)

    Showen, R.L.

    1976-01-01

    Intense plasma waves are generated by an HF pump wave in an ionospheric heating experiment at the Arecibo Observatory. These plasma waves can be observed as enhancements to the ion and plasma lines of the incoherent backscatter echo. The enhancements can be three or four orders of magnitude more intense than the unenhanced lines, and tend to fluctuate wildly. Both the purely growing and the decay mode parametric instabilities are present. When the pump wave is turned on abruptly the enhancements develop in time in a repeatable manner. A rather remarkable feature on time scales of seconds is an overshoot in instability power. These overshoots occur frequently but not universally and last for 1 to 6 seconds. They can have a magnitude from ten to hundreds of times the average instability level. Field aligned irregularities may be the cause of the overshoots. The overshoots appear definitely related to an unusually rapid rise in measured electron temperature that cannot be understood in terms of ohmic energy deposition. On time scales of milliseconds there is a ''mini-overshoot'' before the growth of the instability to a large value. The spectral details also change in a striking manner. The instabilities can first be detected 2 to 4 msec after the pump wave turn-on. The decay mode is present as well as a broad featureless ''noise bump'', which partially sharpens into a line as time progresses. These changes of the spectra in time seem to run counter to the currently accepted theories of plasma wave saturation

  19. Solubility studies of inorganic–organic hybrid nanoparticle photoresists with different surface functional groups

    KAUST Repository

    Li, Li

    2016-01-01

    © 2016 The Royal Society of Chemistry. The solubility behavior of Hf and Zr based hybrid nanoparticles with different surface ligands in different concentrations of photoacid generator as potential EUV photoresists was investigated in detail. The nanoparticles regardless of core or ligand chemistry have a hydrodynamic diameter of 2-3 nm and a very narrow size distribution in organic solvents. The Hansen solubility parameters for nanoparticles functionalized with IBA and 2MBA have the highest contribution from the dispersion interaction than those with tDMA and MAA, which show more polar character. The nanoparticles functionalized with unsaturated surface ligands showed more apparent solubility changes after exposure to DUV than those with saturated ones. The solubility differences after exposure are more pronounced for films containing a higher amount of photoacid generator. The work reported here provides material selection criteria and processing strategies for the design of high performance EUV photoresists.

  20. Observation of magntosphere and ionosphere through HF and VLF standard waves

    International Nuclear Information System (INIS)

    Ogawa, Toru

    1974-01-01

    The observation of magnetosphere and ionosphere through HF and VLF standard waves is a part of the IMS research subject I on the structure and dynamics of the earth's plasmasphere. By receiving the HF and VLF standard waves with high accuracy, and through the changes of the phase and frequency, continuous observation is made concerning the lower plasmasphere at equator and middle/low latitudes and the upper layers in polar regions. In this way, the dynamic state at the time of disturbance such as magnetic storm can be explored. The following matters are described: features of standard-wave observation, purpose and observation plans, the exhcange of data with overseas countries and satellites, and the results of observation expected. (Mori, K.)

  1. 3 and 4 oxidation state element solubilities in borosilicate glasses. Implement to actinides in nuclear glasses; Solubilite des elements aux degres d'oxydation (3) et (4) dans les verres de borosilicate. Application aux actinides dans les verres nucleaires

    Energy Technology Data Exchange (ETDEWEB)

    Cachia, J.N

    2005-12-15

    In order to ensure optimal radionuclides containment, the knowledge of the actinide loading limits in nuclear waste glasses and also the comprehension of the solubilization mechanisms of these elements are essential. A first part of this manuscript deals with the study of the differences in solubility of the tri and tetravalent elements (actinides and surrogates) particularly in function of the melting temperature. The results obtained indicate that trivalent elements (La, Gd, Nd, Am, Cm) exhibit a higher solubility than tetravalent elements (Hf, Th, Pu). Consequently, it was planned to reduce plutonium at the oxidation state (III), the later being essentially tetravalent in borosilicate glasses. An innovating reduction process of multi-valent elements (cerium, plutonium) using silicon nitride has been developed in a second part of this work. Reduced plutonium-bearing glasses synthesized by Si{sub 3}N{sub 4} addition made it possible to double the plutonium solubility from 2 to 4 wt% at 1200 deg C. A structural approach to investigate the differences between tri and tetravalent elements was finally undertaken. These investigations were carried out by X-rays Absorption Spectroscopy (EXAFS) and NMR. Trivalent rare earth and actinide elements seem to behave as network modifiers while tetravalent elements rather present true intermediaries' behaviour. (author)

  2. Soluble porphyrin polymers

    Science.gov (United States)

    Gust, Jr., John Devens; Liddell, Paul Anthony

    2015-07-07

    Porphyrin polymers of Structure 1, where n is an integer (e.g., 1, 2, 3, 4, 5, or greater) ##STR00001## are synthesized by the method shown in FIGS. 2A and 2B. The porphyrin polymers of Structure 1 are soluble in organic solvents such as 2-MeTHF and the like, and can be synthesized in bulk (i.e., in processes other than electropolymerization). These porphyrin polymers have long excited state lifetimes, making the material suitable as an organic semiconductor for organic electronic devices including transistors and memories, as well as solar cells, sensors, light-emitting devices, and other opto-electronic devices.

  3. The magnetic properties of $^{\\rm 177}$Hf and $^{\\rm 180}$Hf in the strong coupling deformed model

    OpenAIRE

    Muto, S.; Stone, N. J.; Bingham, C. R.; Stone, J. R.; Walker, P. M.; Audi, G.; Gaulard, C.; Köster, U.; Nikolov, J.; Nishimura, K.; Ohtsubo, T.; Podolyak, Z.; Risegari, L.; Simpson, G. S.; Veskovic, M.

    2014-01-01

    This paper reports NMR measurements of the magnetic dipole moments of two high-K isomers, the 37/2$^-$, 51.4 m, 2740 keV state in $^{\\rm 177}$Hf and the 8$^-$, 5.5 h, 1142 keV state in $^{\\rm 180}$Hf by the method of on-line nuclear orientation. Also included are results on the angular distributions of gamma transitions in the decay of the $^{\\rm 177}$Hf isotope. These yield high precision E2/M1 multipole mixing ratios for transitions in bands built on the 23/2$^+$, 1.1 s, isomer at 1315 keV ...

  4. Low-Frequency Waves in HF Heating of the Ionosphere

    Science.gov (United States)

    Sharma, A. S.; Eliasson, B.; Milikh, G. M.; Najmi, A.; Papadopoulos, K.; Shao, X.; Vartanyan, A.

    2016-02-01

    Ionospheric heating experiments have enabled an exploration of the ionosphere as a large-scale natural laboratory for the study of many plasma processes. These experiments inject high-frequency (HF) radio waves using high-power transmitters and an array of ground- and space-based diagnostics. This chapter discusses the excitation and propagation of low-frequency waves in HF heating of the ionosphere. The theoretical aspects and the associated models and simulations, and the results from experiments, mostly from the HAARP facility, are presented together to provide a comprehensive interpretation of the relevant plasma processes. The chapter presents the plasma model of the ionosphere for describing the physical processes during HF heating, the numerical code, and the simulations of the excitation of low-frequency waves by HF heating. It then gives the simulations of the high-latitude ionosphere and mid-latitude ionosphere. The chapter also briefly discusses the role of kinetic processes associated with wave generation.

  5. Theoretical Assessment of 178m2Hf De-Excitation

    Energy Technology Data Exchange (ETDEWEB)

    Hartouni, E P; Chen, M; Descalle, M A; Escher, J E; Loshak, A; Navratil, P; Ormand, W E; Pruet, J; Thompson, I J; Wang, T F

    2008-10-06

    This document contains a comprehensive literature review in support of the theoretical assessment of the {sup 178m2}Hf de-excitation, as well as a rigorous description of controlled energy release from an isomeric nuclear state.

  6. HF Surface Wave Radar Operation in Adverse Conditions

    National Research Council Canada - National Science Library

    Ponsford, Anthony M; Dizaji, Reza M; McKerracher, Richard

    2005-01-01

    ...) system based on HF Surface Wave Radar (HFSWR). the primary objective behind the programme was to demonstrate the capability of HFSWR to continuously detect and track surface targets (ships and icebergs...

  7. HF band filter bank multi-carrier spread spectrum

    Energy Technology Data Exchange (ETDEWEB)

    Laraway, Stephen Andrew; Moradi, Hussein; Farhang-Boroujeny, Behrouz

    2015-10-01

    Abstract—This paper describes modifications to the filter bank multicarrier spread spectrum (FB-MC-SS) system, that was presented in [1] and [2], to enable transmission of this waveform in the HF skywave channel. FB-MC-SS is well suited for the HF channel because it performs well in channels with frequency selective fading and interference. This paper describes new algorithms for packet detection, timing recovery and equalization that are suitable for the HF channel. Also, an algorithm for optimizing the peak to average power ratio (PAPR) of the FBMC- SS waveform is presented. Application of this algorithm results in a waveform with low PAPR. Simulation results using a wide band HF channel model demonstrate the robustness of this system over a wide range of delay and Doppler spreads.

  8. HF-voltage testing of accelerating system functional model

    International Nuclear Information System (INIS)

    Gladkov, A.V.; Stepanov, V.B.

    1989-01-01

    Owing to ambiguity in interpreting the notion of the electron strength of the operating HF device in an acceleator a technique of measurements and result processing, based on statistical analysis of the data is suggested. Experimental testing on electric strength of structures with HF focusing was carried out using a bench in the form of a cylindrical vacuum container inside which a double H-resonator with HF quadrupole electrodes without surface modulation was installed. The dependences obtained permit to evaluate the bahaviour of the HF device from the viewpoint of electric strength and radiation hazard for the whole range of possible values of voltage on the basis of data on the frequency of breakdowns and radiation situation only in one experimental point. 12 refs.; 8 figs

  9. Mechanistic Insight into the Stability of HfO2-Coated MoS2 Nanosheet Anodes for Sodium Ion Batteries

    KAUST Repository

    Ahmed, Bilal

    2015-06-01

    It is demonstrated for the first time that surface passivation of 2D nanosheets of MoS2 by an ultrathin and uniform layer of HfO2 can significantly improve the cyclic performance of sodium ion batteries. After 50 charge/discharge cycles, bare MoS2 and HfO2 coated MoS2 electrodes deliver the specific capacity of 435 and 636 mAh g-1, respectively, at current density of 100 mA g-1. These results imply that batteries using HfO2 coated MoS2 anodes retain 91% of the initial capacity; in contrast, bare MoS2 anodes retain only 63%. Also, HfO2 coated MoS2 anodes show one of the highest reported capacity values for MoS2. Cyclic voltammetry and X-ray photoelectron spectroscopy results suggest that HfO2 does not take part in electrochemical reaction. The mechanism of capacity retention with HfO2 coating is explained by ex situ transmission electron microscope imaging and electrical impedance spectroscopy. It is illustrated that HfO2 acts as a passivation layer at the anode/electrolyte interface and prevents structural degradation during charge/discharge process. Moreover, the amorphous nature of HfO2 allows facile diffusion of Na ions. These results clearly show the potential of HfO2 coated MoS2 anodes, which performance is significantly higher than previous reports where bulk MoS2 or composites of MoS2 with carbonaceous materials are used. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Mechanistic Insight into the Stability of HfO2-Coated MoS2 Nanosheet Anodes for Sodium Ion Batteries

    KAUST Repository

    Ahmed, Bilal; Anjum, Dalaver H.; Hedhili, Mohamed N.; Alshareef, Husam N.

    2015-01-01

    It is demonstrated for the first time that surface passivation of 2D nanosheets of MoS2 by an ultrathin and uniform layer of HfO2 can significantly improve the cyclic performance of sodium ion batteries. After 50 charge/discharge cycles, bare MoS2 and HfO2 coated MoS2 electrodes deliver the specific capacity of 435 and 636 mAh g-1, respectively, at current density of 100 mA g-1. These results imply that batteries using HfO2 coated MoS2 anodes retain 91% of the initial capacity; in contrast, bare MoS2 anodes retain only 63%. Also, HfO2 coated MoS2 anodes show one of the highest reported capacity values for MoS2. Cyclic voltammetry and X-ray photoelectron spectroscopy results suggest that HfO2 does not take part in electrochemical reaction. The mechanism of capacity retention with HfO2 coating is explained by ex situ transmission electron microscope imaging and electrical impedance spectroscopy. It is illustrated that HfO2 acts as a passivation layer at the anode/electrolyte interface and prevents structural degradation during charge/discharge process. Moreover, the amorphous nature of HfO2 allows facile diffusion of Na ions. These results clearly show the potential of HfO2 coated MoS2 anodes, which performance is significantly higher than previous reports where bulk MoS2 or composites of MoS2 with carbonaceous materials are used. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  11. Integrated magnetics design for HF-link power converters

    Energy Technology Data Exchange (ETDEWEB)

    Ljusev, P.; Andersen, Michael A.E.

    2005-07-01

    This paper deals with the design of integrated magnetics for HF-link converters, where the two integrated magnetic components on the same core do not necessarily belong to the same voltage loop. Depending on the specific HF-link converter topology, the proposed integrated magnetics can either alleviate the derivation of independent auxiliary supply voltages from the main transformer or integrate other magnetic structures, thus saving board space and cutting costs. (au)

  12. Large Magnetic Anisotropy in HfMnP

    Science.gov (United States)

    Parker, David; Lamichhane, Tej; Taufour, Valentin; Masters, Morgan; Thimmaiah, Srinivasa; Bud'Ko, Ser'gey; Canfield, Paul

    We present a theoretical and experimental study of two little-studied manganese phosphide ferromagnets, HfMnP and ZrMnP, with Curie temperatures above room temperature. We find an anisotropy field in HfMnP approaching 10 T - larger than that of the permanent magnet workhorse NdFeB magnets. From theory we determine the source of this anisotropy. Our results show the potential of 3d-element-based magnetic materials for magnetic applications.

  13. Angiogenesis mediated by soluble forms of E-selectin and vascular cell adhesion molecule-1

    Science.gov (United States)

    Koch, Alisa E.; Halloran, Margaret M.; Haskell, Catherine J.; Shah, Manisha R.; Polverini, Peter J.

    1995-08-01

    ENDOTHELIAL adhesion molecules facilitate the entry of leukocytes into inflamed tissues. This in turn promotes neovascularization, a process central to the progression of rheumatoid arthritis, tumour growth and wound repair1. Here we test the hypothesis that soluble endothelial adhesion molecules promote angiogenesis2á¤-4. Human recombinant soluble E-selectin and soluble vascular cell adhesion molecule-1 induced chemotaxis of human endothelial cells in vitro and were angiogenic in rat cornea. Soluble E-selectin acted on endothelial cells in part through a sialyl Lewis-X-dependent mechanism, while soluble vascular cell adhesion molecule-1 acted on endothelial cells in part through a very late antigen (VLA)-4 dependent mechanism. The chemotactic activity of rheumatoid synovial fluid for endothelial cells, and also its angiogenic activity, were blocked by antibodies to either soluble E-selectin or soluble vascular cell adhesion molecule-1. These results suggest a novel function for soluble endothelial adhesion molecules as mediators of angiogenesis.

  14. Thermoelectric properties of doped BaHfO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Dixit, Chandra Kr., E-mail: ckparadise@gmail.com, E-mail: sharmarameshfgiet@gmail.com [Dept. of Physics, Dr. Shakuntala Misra National Rehabilitation University, Lucknow-229001, U.P India (India); Bhamu, K. C. [Department of Physics, Goa University, Goa-403 206 (India); Sharma, Ramesh, E-mail: ckparadise@gmail.com, E-mail: sharmarameshfgiet@gmail.com [Dept. of Physics, Feroze Gandhi Institute of Engineering & Technology, Raebareli-229001, U.P India (India)

    2016-05-06

    We have studied the structural stability, electronic structure, optical properties and thermoelectric properties of doped BaHfO{sub 3} by full potential linearized augmented plane wave (FP-LAPW) method. The electronic structure of BaHfO{sub 3} doped with Sr shows enhances the indirect band gaps of 3.53 eV, 3.58 eV. The charge density plots show strong ionic bonding in Ba-Hf, and ionic and covalent bonding between Hf and O. Calculations of the optical spectra, viz., the dielectric function, refractive index and extinction coefficient are performed for the energy range are calculated and analyzed. Thermoelectric properties of semi conducting are also reported first time. The doped BaHfO{sub 3} is approximately wide band gap semiconductor with the large p-type Seebeck coefficient. The power factor of BaHfO{sub 3} is increased with Sr doping, decreases because of low electrical resistivity and thermal conductivity.

  15. The isobutylene-isobutane alkylation process in liquid HF revisited.

    Science.gov (United States)

    Esteves, P M; Araújo, C L; Horta, B A C; Alvarez, L J; Zicovich-Wilson, C M; Ramírez-Solís, A

    2005-07-07

    Details on the mechanism of HF catalyzed isobutylene-isobutane alkylation were investigated. On the basis of available experimental data and high-level quantum chemical calculations, a detailed reaction mechanism is proposed taking into account solvation effects of the medium. On the basis of our computational results, we explain why the density of the liquid media and stirring rates are the most important parameters to achieve maximum yield of alkylate, in agreement with experimental findings. The ab initio Car-Parrinello molecular dynamics calculations show that isobutylene is irreversibly protonated in the liquid HF medium at higher densities, leading to the ion pair formation, which is shown to be a minimum on the potential energy surface after optimization using periodic boundary conditions. The HF medium solvates preferentially the fluoride anion, which is found as solvated [FHF](-) or solvated F(-.)(HF)(3). On the other hand, the tert-butyl cation is weakly solvated, where the closest HF molecules appear at a distance of about 2.9 Angstrom with the fluorine termination of an HF chain.

  16. Solid phase crystallisation of HfO2 thin films

    International Nuclear Information System (INIS)

    Modreanu, M.; Sancho-Parramon, J.; O'Connell, D.; Justice, J.; Durand, O.; Servet, B.

    2005-01-01

    In this paper, we report on the solid phase crystallisation of carbon-free HfO 2 thin films deposited by plasma ion assisted deposition (PIAD). After deposition, the HfO 2 films were annealed in N 2 ambient for 3 h at 350, 550 and 750 deg. C. Several characterisation techniques including X-ray reflectometry (XRR), X-ray diffraction (XRD), spectroscopic ellipsometry (SE) and atomic force microscopy (AFM) were used for the physical characterisation of as-deposited and annealed HfO 2 . XRD has revealed that the as-deposited HfO 2 film is in an amorphous-like state with only traces of crystalline phase and that the annealed films are in a highly crystalline state. These results are in good agreement with the SE results showing an increase of refractive index by increasing the annealing temperature. XRR results show a significant density gradient over the as-deposited film thickness, which is characteristic of the PIAD method. The AFM measurements show that the HfO 2 layers have a smooth surface even after annealing at 750 deg. C. The present study demonstrates that the solid phase crystallisation of HfO 2 PIAD thin films starts at a temperature as low as 550 deg. C

  17. Sequential sputtered Co-HfO{sub 2} granular films

    Energy Technology Data Exchange (ETDEWEB)

    Chadha, M.; Ng, V.

    2017-03-15

    A systematic study of magnetic, magneto-transport and micro-structural properties of Co-HfO{sub 2} granular films fabricated by sequential sputtering is presented. We demonstrate reduction in ferromagnetic-oxide formation by using HfO{sub 2} as the insulting matrix. Microstructure evaluation of the films showed that the film structure consisted of discrete hcp-Co grains embedded in HfO{sub 2} matrix. Films with varying compositions were prepared and their macroscopic properties were studied. We correlate the variation in these properties to the variation in film microstructure. Our study shows that Co-HfO{sub 2} films with reduced cobalt oxide and varying properties can be prepared using sequential sputtering technique. - Highlights: • Co-HfO{sub 2} granular films were prepared using sequential sputtering. • A reduction in ferromagnetic-oxide formation is observed. • Co-HfO{sub 2} films display superparamagnetism and tunnelling magneto-resistance. • Varying macroscopic properties were achieved by changing film composition. • Applications can be found in moderate MR sensors and high –frequency RF devices.

  18. Hafnium in peralkaline and peraluminous boro-aluminosilicate glass, and glass subcomponents: a solubility study

    International Nuclear Information System (INIS)

    Davis, Linda L.; Darab, John G.; Qian, Maoxu; Zhao, Donggao; Palenik, Christopher S.; Li, Hong; Strachan, Denis M.; Li, Liyu

    2003-01-01

    A relationship between the solubility of hafnia (HfO2) and the host glass composition was explored by determining the solubility limits of HfO2 in peralkaline and peraluminous borosilicate glasses in the system SiO2-Al2O3-B2O3-Na2O, and in glasses in the system SiO2-Na2O-Al2O3 in air at 1450 C. The only Hf-bearing phase to crystallize in the peralkaline borosilicate melts is hafnia, while in the boron-free melts sodium-hafnium silicates crystallize. All peraluminous borosilicate melts crystallize hafnia, but the slightly peraluminous glasses also have sector-zoned hafnia crystals that contain Al and Si. The more peraluminous borosilicate glasses also crystallize a B-containing mullite. The general morphology of the hafnia crystals changes as peralkalinity (Na2O/(Na2O+Al2O3)) decreases, as expected in melts with increasing viscosity. In all of the glasses with Na2O > Al2O3, the solubility of hafnia is linearly and positively correlated with Na2O/(Na2O + Al2O3) or Na2O - Al2O3 (excess sodium), despite the presence of 5 to 16 mol% B2O3. The solubility of hafnia is higher in the sodium-aluminum borosilicate glasses than in the sodium-aluminosilicate glasses, suggesting that the boron is enhancing the effect that excess sodium has on the incorporation of Hf into the glass structure. The results of this solubility study are compared to other studies of high-valence cation solubility in B-free silicate melts. From this, for peralkaline B-bearing glasses, it is shown that, although the solubility limits are higher, the solution behavior of hafnia is the same as in B-free silicate melts previously studied. By comparison, also, it is shown that in peraluminous melts, there must be a different solution mechanism for hafnia: different than for peralkaline sodium-aluminum borosilicate glasses and different than for B-free silicate melts studied by others

  19. Reconciliation of the excess 176Hf conundrum in meteorites: Recent disturbances of the Lu-Hf and Sm-Nd isotope systematics

    Science.gov (United States)

    Bast, Rebecca; Scherer, Erik E.; Sprung, Peter; Mezger, Klaus; Fischer-Gödde, Mario; Taetz, Stephan; Böhnke, Mischa; Schmid-Beurmann, Hinrich; Münker, Carsten; Kleine, Thorsten; Srinivasan, Gopalan

    2017-09-01

    The long-lived 176Lu-176Hf and 147Sm-143Nd radioisotope systems are commonly used chronometers, but when applied to meteorites, they can reveal disturbances. Specifically, Lu-Hf isochrons commonly yield dates up to ∼300 Myr older than the solar system and varying initial 176Hf/177Hf values. We investigated this problem by attempting to construct mineral and whole rock isochrons for eucrites and angrites. Meteorites from different parent bodies exhibit similar disturbance features suggesting that a common process is responsible. Minerals scatter away from isochron regressions for both meteorite classes, with low-Hf phases such as plagioclase and olivine typically being most displaced above (or left of) reference isochrons. Relatively Hf-rich pyroxene is less disturbed but still to the point of steepening Lu-Hf errorchrons. Using our Lu-Hf and Sm-Nd data, we tested various Hf and Lu redistribution scenarios and found that decoupling of Lu/Hf from 176Hf/177Hf must postdate the accumulation of significant radiogenic 176Hf. Therefore early irradiation or diffusion cannot explain the excess 176Hf. Instead, disturbed meteorite isochrons are more likely caused by terrestrial weathering, contamination, or common laboratory procedures. The partial dissolution of phosphate minerals may predominantly remove rare earth elements including Lu, leaving relatively immobile and radiogenic Hf behind. Robust Lu-Hf (and improved Sm-Nd) meteorite geochronology will require the development of chemical or physical methods for removing unsupported radiogenic Hf and silicate-hosted terrestrial contaminants without disturbing parent-daughter ratios.

  20. Tracking magmatic processes through Zr/Hf ratios in rocks and Hf and Ti zoning in zircons: An example from the Spirit Mountain batholith, Nevada

    Science.gov (United States)

    Lowery, Claiborne L.E.; Miller, C.F.; Walker, B.A.; Wooden, J.L.; Mazdab, F.K.; Bea, F.

    2006-01-01

    Zirconium and Hf are nearly identical geochemically, and therefore most of the crust maintains near-chondritic Zr/Hf ratios of ???35-40. By contrast, many high-silica rhyolites and granites have anomalously low Zr/Hf (15-30). As zircon is the primary reservoir for both Zr and Hf and preferentially incorporates Zr, crystallization of zircon controls Zr/ Hf, imprinting low Zr/Hf on coexisting melt. Thus, low Zr/Hf is a unique fingerprint of effective magmatic fractionation in the crust. Age and compositional zonation in zircons themselves provide a record of the thermal and compositional histories of magmatic systems. High Hf (low Zr/ Hf) in zircon zones demonstrates growth from fractionated melt, and Ti provides an estimate of temperature of crystallization (TTiZ) (Watson and Harrison, 2005). Whole-rock Zr/Hf and zircon zonation in the Spirit Mountain batholith, Nevada, document repeated fractionation and thermal fluctuations. Ratios of Zr/Hf are ???30-40 for cumulates and 18-30 for high-SiO2 granites. In zircons, Hf (and U) are inversely correlated with Ti, and concentrations indicate large fluctuations in melt composition and TTiZ (>100??C) for individual zircons. Such variations are consistent with field relations and ion-probe zircon geochronology that indicate a >1 million year history of repeated replenishment, fractionation, and extraction of melt from crystal mush to form the low Zr/Hf high-SiO2 zone. ?? 2006 The Mineralogical Society.

  1. Isothermal cross-sections of Hf-Sc-Ga(800 deg C) and Hf-Ti-Ga (750 deg C) phase diagrams

    International Nuclear Information System (INIS)

    Markiv, V.Ya.; Belyavina, N.N.

    1981-01-01

    Isothermal cross sections of Hf-Sc-Ga (800 deg C) and Hf-Ti-Ga (750 deg C) state diagrams are plotted. The existence of two ternary Hfsub(0.1-0.8)Scsub(0.9)-sub(0.2)Ga and Hfsub(0.8)Scsub(0.2)Gasub(3) phases is stated in the Hf-Sc-Ga system. The crystal structure of these compounds investigated by the powder method belongs to the structural α-MoB and ZrAl 3 types respectively. Continuous rows of (Hf, Sc 5 Ga 5 , (Hf, Ti)Ga 3 and (Hf, Ti)Ga 2 solid solutions are formed in the investigated systems. Essential quantity of the third component dissolve binary Sc 5 Ga 4 , Sc 2 Ga 3 (15 and 30 at % Hf respectively), Hf 5 Ga 4 , HfGa 2 (20, 10 at. % Sc), Hf 5 Ga 4 , HfGa, Hf 5 Ga 3 , Hf 2 Ga 3 (48, 30, 46, 20 at. % Ti) gallides [ru

  2. Lattice Thermal Conductivity from Atomistic Simulations: ZrB2 and HfB2

    Science.gov (United States)

    Lawson, John W.; Daw, Murray S.; Bauschlicher, Charles W.

    2012-01-01

    Ultra high temperature ceramics (UHTC) including ZrB2 and HfB2 have a number of properties that make them attractive for applications in extreme environments. One such property is their high thermal conductivity. Computational modeling of these materials will facilitate understanding of fundamental mechanisms, elucidate structure-property relationships, and ultimately accelerate the materials design cycle. Progress in computational modeling of UHTCs however has been limited in part due to the absence of suitable interatomic potentials. Recently, we developed Tersoff style parameterizations of such potentials for both ZrB2 and HfB2 appropriate for atomistic simulations. As an application, Green-Kubo molecular dynamics simulations were performed to evaluate the lattice thermal conductivity for single crystals of ZrB2 and HfB2. The atomic mass difference in these binary compounds leads to oscillations in the time correlation function of the heat current, in contrast to the more typical monotonic decay seen in monoatomic materials such as Silicon, for example. Results at room temperature and at elevated temperatures will be reported.

  3. Ge interactions on HfO2 surfaces and kinetically driven patterning of Ge nanocrystals on HfO2

    International Nuclear Information System (INIS)

    Stanley, Scott K.; Joshi, Sachin V.; Banerjee, Sanjay K.; Ekerdt, John G.

    2006-01-01

    Germanium interactions are studied on HfO 2 surfaces, which are prepared through physical vapor deposition (PVD) and by atomic layer deposition. X-ray photoelectron spectroscopy and temperature-programed desorption are used to follow the reactions of germanium on HfO 2 . Germanium chemical vapor deposition at 870 K on HfO 2 produces a GeO x adhesion layer, followed by growth of semiconducting Ge 0 . PVD of 0.7 ML Ge (accomplished by thermally cracking GeH 4 over a hot filament) also produces an initial GeO x layer, which is stable up to 800 K. PVD above 2.0 ML deposits semiconducting Ge 0 . Temperature programed desorption experiments of ∼1.0 ML Ge from HfO 2 at 400-1100 K show GeH 4 desorption below 600 K and GeO desorption above 850 K. These results are compared to Ge on SiO 2 where GeO desorption is seen at 550 K. Exploiting the different reactivity of Ge on HfO 2 and SiO 2 allows a kinetically driven patterning scheme for high-density Ge nanoparticle growth on HfO 2 surfaces that is demonstrated

  4. Theoretical predictions of hydrolysis and complex formation of group-4 elements Zr, Hf and Rf in HF and HCl solutions

    International Nuclear Information System (INIS)

    Pershina, V.; Trubert, D.; Le Naour, C.; Kratz, J.V.

    2002-01-01

    Fully relativistic molecular density-functional calculations of the electronic structures of hydrated, hydrolyzed and fluoride/chloride complexes have been performed for group-4 elements Zr, Hf, and element 104, Rf. Using the electronic density distribution data, relative values of the free energy change for hydrolysis and complex formation reactions were defined. The results show the following trend for the first hydrolysis step of the cationic species: Zr>Hf>Rf in agreement with experiments. For the complex formation in HF solutions, the trend to a decrease from Zr to Hf is continued with Rf, provided no hydrolysis takes place. At pH>0, further fluorination of hydrolyzed species or fluoro-complexes has an inversed trend in the group Rf≥Zr>Hf, with the difference between the elements being very small. For the complex formation in HCl solutions, the trend is continued with Rf, so that Zr>Hf>Rf independently of pH. A decisive energetic factor in hydrolysis or complex formation processes proved to be a predominant electrostatic metal-ligand interaction. Trends in the K d (distribution coefficient) values for the group-4 elements are expected to follow those of the complex formation

  5. Relationship between CCR and NT-proBNP in Chinese HF patients, and their correlations with severity of HF.

    Science.gov (United States)

    Lu, Zhigang; Wang, Bo; Wang, Yunliang; Qian, Xueqing; Zheng, Wei; Wei, Meng

    2014-01-01

    To evaluate the relationship between creatinine clearance rate (CCR) and the level of N-terminal pro-B-type natriuretic peptide (NT-proBNP) in heart failure (HF) patients and their correlations with HF severity. Two hundred and one Chinese patients were grouped according to the New York Heart Association (NYHA) classification as NYHA 1-2 and 3-4 groups and 135 cases out of heart failure patients as control group. The following variables were compared among these three groups: age, sex, body mass index (BMI), smoking status, hypertension, diabetes, NT-proBNP, creatinine (Cr), uric acid (UA), left ventricular end-diastolic diameter (LVEDD), and CCR. The biomarkers of NT-proBNP, Cr, UA, LVEDD, and CCR varied significantly in the three groups, and these variables were positively correlated with the NHYA classification. The levels of NT-proBNP and CCR were closely related to the occurrence of HF and were independent risk factors for HF. At the same time, there was a significant negative correlation between the levels of NT-proBNP and CCR. The area under the receiver operating characteristic curve suggested that the NT-proBNP and CCR have high accuracy for diagnosis of HF and have clinical diagnostic value. NT-proBNP and CCR may be important biomarkers in evaluating the severity of HF.

  6. Joint Efforts Towards European HF Radar Integration

    Science.gov (United States)

    Rubio, A.; Mader, J.; Griffa, A.; Mantovani, C.; Corgnati, L.; Novellino, A.; Schulz-Stellenfleth, J.; Quentin, C.; Wyatt, L.; Ruiz, M. I.; Lorente, P.; Hartnett, M.; Gorringe, P.

    2016-12-01

    During the past two years, significant steps have been made in Europe for achieving the needed accessibility to High Frequency Radar (HFR) data for a pan-European use. Since 2015, EuroGOOS Ocean Observing Task Teams (TT), such as HFR TT, are operational networks of observing platforms. The main goal is on the harmonization of systems requirements, systems design, data quality, improvement and proof of the readiness and standardization of HFR data access and tools. Particular attention is being paid by HFR TT to converge from different projects and programs toward those common objectives. First, JERICO-NEXT (Joint European Research Infrastructure network for Coastal Observatory - Novel European eXpertise for coastal observaTories, H2020 2015 Programme) will contribute on describing the status of the European network, on seeking harmonization through exchange of best practices and standardization, on developing and giving access to quality control procedures and new products, and finally on demonstrating the use of such technology in the general scientific strategy focused by the Coastal Observatory. Then, EMODnet (European Marine Observation and Data Network) Physics started to assemble HF radar metadata and data products within Europe in a uniform way. This long term program is providing a combined array of services and functionalities to users for obtaining free of charge data, meta-data and data products on the physical conditions of European sea basins and oceans. Additionally, the Copernicus Marine Environment Monitoring Service (CMEMS) delivers from 2015 a core information service to any user related to 4 areas of benefits: Maritime Safety, Coastal and Marine Environment, Marine Resources, and Weather, Seasonal Forecasting and Climate activities. INCREASE (Innovation and Networking for the integration of Coastal Radars into EuropeAn marine SErvices - CMEMS Service Evolution 2016) will set the necessary developments towards the integration of existing European

  7. Within-Site Variation in Feather Stable Hydrogen Isotope (δ2Hf) Values of Boreal Songbirds: Implications for Assignment to Molt Origin.

    Science.gov (United States)

    Nordell, Cameron J; Haché, Samuel; Bayne, Erin M; Sólymos, Péter; Foster, Kenneth R; Godwin, Christine M; Krikun, Richard; Pyle, Peter; Hobson, Keith A

    2016-01-01

    Understanding bird migration and dispersal is important to inform full life-cycle conservation planning. Stable hydrogen isotope ratios from feathers (δ2Hf) can be linked to amount-weighted long-term, growing season precipitation δ2H (δ2Hp) surfaces to create δ2Hf isoscapes for assignment to molt origin. However, transfer functions linking δ2Hp with δ2Hf are influenced by physiological and environmental processes. A better understanding of the causes and consequences of variation in δ2Hf values among individuals and species will improve the predictive ability of geographic assignment tests. We tested for effects of species, land cover, forage substrate, nest substrate, diet composition, body mass, sex, and phylogenetic relatedness on δ2Hf from individuals at least two years old of 21 songbird species captured during the same breeding season at a site in northeastern Alberta, Canada. For four species, we also tested for a year × species interaction effect on δ2Hf. A model including species as single predictor received the most support (AIC weight = 0.74) in explaining variation in δ2Hf. A species-specific variance parameter was part of all best-ranked models, suggesting variation in δ2Hf was not consistent among species. The second best-ranked model included a forage substrate × diet interaction term (AIC weight = 0.16). There was a significant year × species interaction effect on δ2Hf suggesting that interspecific differences in δ2Hf can differ among years. Our results suggest that within- and among-year interspecific variation in δ2Hf is the most important source of variance typically not being explicitly quantified in geographic assignment tests using non-specific transfer functions to convert δ2Hp into δ2Hf. However, this source of variation is consistent with the range of variation from the transfer functions most commonly being propagated in assignment tests of geographic origins for passerines breeding in North America.

  8. PLUTONIUM SOLUBILITY IN HIGH-LEVEL WASTE ALKALI BOROSILICATE GLASS

    Energy Technology Data Exchange (ETDEWEB)

    Marra, J.; Crawford, C.; Fox, K.; Bibler, N.

    2011-01-04

    The solubility of plutonium in a Sludge Batch 6 (SB6) reference glass and the effect of incorporation of Pu in the glass on specific glass properties were evaluated. A Pu loading of 1 wt % in glass was studied. Prior to actual plutonium glass testing, surrogate testing (using Hf as a surrogate for Pu) was conducted to evaluate the homogeneity of significant quantities of Hf (Pu) in the glass, determine the most appropriate methods to evaluate homogeneity for Pu glass testing, and to evaluate the impact of Hf loading in the glass on select glass properties. Surrogate testing was conducted using Hf to represent between 0 and 1 wt % Pu in glass on an equivalent molar basis. A Pu loading of 1 wt % in glass translated to {approx}18 kg Pu per Defense Waste Processing Facility (DWPF) canister, or about 10X the current allowed limit per the Waste Acceptance Product Specifications (2500 g/m{sup 3} of glass or about 1700 g/canister) and about 30X the current allowable concentration based on the fissile material concentration limit referenced in the Yucca Mountain Project License Application (897 g/m{sup 3}3 of glass or about 600 g Pu/canister). Based on historical process throughput data, this level was considered to represent a reasonable upper bound for Pu loading based on the ability to provide Pu containing feed to the DWPF. The task elements included evaluating the distribution of Pu in the glass (e.g. homogeneity), evaluating crystallization within the glass, evaluating select glass properties (with surrogates), and evaluating durability using the Product Consistency Test -- Method A (PCT-A). The behavior of Pu in the melter was evaluated using paper studies and corresponding analyses of DWPF melter pour samples.The results of the testing indicated that at 1 wt % Pu in the glass, the Pu was homogeneously distributed and did not result in any formation of plutonium-containing crystalline phases as long as the glass was prepared under 'well-mixed' conditions

  9. Plutonium Solubility In High-Level Waste Alkali Borosilicate Glass

    International Nuclear Information System (INIS)

    Marra, J.; Crawford, C.; Fox, K.; Bibler, N.

    2011-01-01

    The solubility of plutonium in a Sludge Batch 6 (SB6) reference glass and the effect of incorporation of Pu in the glass on specific glass properties were evaluated. A Pu loading of 1 wt % in glass was studied. Prior to actual plutonium glass testing, surrogate testing (using Hf as a surrogate for Pu) was conducted to evaluate the homogeneity of significant quantities of Hf (Pu) in the glass, determine the most appropriate methods to evaluate homogeneity for Pu glass testing, and to evaluate the impact of Hf loading in the glass on select glass properties. Surrogate testing was conducted using Hf to represent between 0 and 1 wt % Pu in glass on an equivalent molar basis. A Pu loading of 1 wt % in glass translated to ∼18 kg Pu per Defense Waste Processing Facility (DWPF) canister, or about 10X the current allowed limit per the Waste Acceptance Product Specifications (2500 g/m 3 of glass or about 1700 g/canister) and about 30X the current allowable concentration based on the fissile material concentration limit referenced in the Yucca Mountain Project License Application (897 g/m 3 3 of glass or about 600 g Pu/canister). Based on historical process throughput data, this level was considered to represent a reasonable upper bound for Pu loading based on the ability to provide Pu containing feed to the DWPF. The task elements included evaluating the distribution of Pu in the glass (e.g. homogeneity), evaluating crystallization within the glass, evaluating select glass properties (with surrogates), and evaluating durability using the Product Consistency Test -- Method A (PCT-A). The behavior of Pu in the melter was evaluated using paper studies and corresponding analyses of DWPF melter pour samples.The results of the testing indicated that at 1 wt % Pu in the glass, the Pu was homogeneously distributed and did not result in any formation of plutonium-containing crystalline phases as long as the glass was prepared under 'well-mixed' conditions. The incorporation of 1 wt

  10. Coulomb-nuclear interference measurements of 168Yb, 176Hf, 178Hf, and 180Hf and lifetime measurements in 186Hg

    International Nuclear Information System (INIS)

    Nettles, W.G.

    1979-01-01

    Alpha scattering measurements were performed at center-of-mass energies near the Coulomb barrier. These energies allow for nuclear as well as pure Coulomb forces to play a significant role in the excitation process. The interference of these two forces is very sensitive to the sign of the E4 ground-state moment, whereas pure Coulomb excitation is not. Systematics of the E4 moments of the rare earth mass region indicate a transition in the magnitude and sign of the reduced matrix element of the M(E4) operator between 0 + and 4 + states from small and positive to large and negative between Yb and W. Previous Coulomb-nuclear interference measurements show that this reduced matrix element for 180 Hf is large and negative. The present results agree with that conclusion. It is also shown that the above reduced matrix element for 178 Hf, like that of 180 Hf, is large and negative. The small and positive moment (matrix element) for 168 Yb is seen to be consistent with the experimental data. No conclusions are drawn for the E4 moment in 176 Hf. The measurement of nuclear lifetimes shorter than 500 ps requires the use of plastic scintilltor detectors. These detectors, however have very poor energy resolution. A system is described that uses plastic scintillators with a magnetic lens spectrometer for energy selection. The system was used to measure the lifetime of the 522-keV 0 + sate in 186 Hf. A data analysis method using higher-order distribution moments is also presented

  11. Water-soluble vitamins.

    Science.gov (United States)

    Konings, Erik J M

    2006-01-01

    Simultaneous Determination of Vitamins.--Klejdus et al. described a simultaneous determination of 10 water- and 10 fat-soluble vitamins in pharmaceutical preparations by liquid chromatography-diode-array detection (LC-DAD). A combined isocratic and linear gradient allowed separation of vitamins in 3 distinct groups: polar, low-polar, and nonpolar. The method was applied to pharmaceutical preparations, fortified powdered drinks, and food samples, for which results were in good agreement with values claimed. Heudi et al. described a separation of 9 water-soluble vitamins by LC-UV. The method was applied for the quantification of vitamins in polyvitaminated premixes used for the fortification of infant nutrition products. The repeatability of the method was evaluated at different concentration levels and coefficients of variation were based on, for example, LC. Koontz et al. showed results of total folate concentrations measured by microbiological assay in a variety of foods. Samples were submitted in a routine manner to experienced laboratories that regularly perform folate analysis fee-for-service basis in the United States. Each laboratory reported the use of a microbiological method similar to the AOAC Official Method for the determination of folic acid. Striking was, the use of 3 different pH extraction conditions by 4 laboratories. Only one laboratory reported using a tri-enzyme extraction. Results were evaluated. Results for folic acid fortified foods had considerably lower between-laboratory variation, 9-11%, versus >45% for other foods. Mean total folate ranged from 14 to 279 microg/100 g for a mixed vegetable reference material, from 5 to 70 microg/100 g for strawberries, and from 28 to 81 microg/100 g for wholemeal flour. One should realize a large variation in results, which might be caused by slight modifications in the microbiological analysis of total folate in foods or the analysis in various (unfortified) food matrixes. Furthermore, optimal

  12. [Effect of a multifunctional instrument (HF scissors) in parotis surgery].

    Science.gov (United States)

    Strauss, G; Schaller, S; Gollnick, I

    2014-03-01

    Lateral parotidectomy is a demanding surgical procedure and requires a large number of instruments with a high frequency (HF) of alternating. Many functions, such as preparing, spreading, coagulating and cutting could be combined by using scissors with an integrated function of bipolar coagulation. This study has targeted an investigation of technical application, influence on surgery time, frequency of HF application and change of instruments. In the period between 01 April 2011 and 30 September 2012 (18 months) 35 procedures of lateral parotidectomy in 35 patients were investigated. In all cases lateral parotidectomy was carried out with a similar technique (modified extracapsular preparation). Workflow data were used from a control group in the period between 01 January 2009 and 31 December 2010 (24 months). The following parameters from both groups were documented and evaluated: incision-suture times (subdivided into nine sections of the procedure), change of instruments, period of application for HF function and early facial nerve function (6 h and 6 days after surgery according to House-Brackmann). Additionally, in the HF+ group a questionnaire that facilitated subjective evaluation of instruments was analyzed. It was possible to perform the surgery in both groups with neither technical nor surgical intraoperative complications. Incision-suture times showed an average reduction of 31.6 min (34.8 %) in the HF+ group. There was a reduction in the change of instruments compared to a conventional group (CONV) by up to 62.7 %. With the deployment of HF scissors there was a clear increase in the use of HF surgery by more than 100 % when comparing incision-suture times. Evaluation of both groups according to House-Brackmann showed a similar postoperative facial nerve function. The surgeons involved were of the opinion that in all 35 surgeries with HF scissors the intervention was easier and more comfortable. The use of HF scissors is appropriate for parotid gland

  13. The influence of thermal treatment on the phase development in HfO2-Al2O3 and ZrO2-Al2O3 systems

    International Nuclear Information System (INIS)

    Stefanic, G.; Music, S.; Trojko, R.

    2005-01-01

    Amorphous precursors of HfO 2 -AlO 1.5 and ZrO 2 -AlO 1.5 systems covering the whole concentration range were co-precipitated from aqueous solutions of the corresponding salts. The thermal behaviour of the amorphous precursors was examined by differential thermal analysis, X-ray powder diffraction (XRD), laser Raman spectroscopy and scanning electron microscopy. The crystallization temperature of both systems increased with increase in the AlO 1.5 content, from 530 to 940 deg. C in the HfO 2 -AlO 1.5 system, and from 405 to 915 deg. C in the ZrO 2 -AlO 1.5 system. The results of phase analysis indicate an extended capability for the incorporation of Al 3+ ions in the metastable HfO 2 - and ZrO 2 -type solid solutions obtained after crystallization of amorphous co-gels. Precise determination of lattice parameters, performed using whole-powder-pattern decomposition method, showed that the axial ratio c f /a f in the ZrO 2 - and HfO 2 -type solid solutions with 10 mol% or more of Al 3+ approach 1. The tetragonal symmetry of these samples, as determined by laser Raman spectroscopy, was attributed to the displacement of the oxygen sublattice from the ideal fluorite positions. It was found that the lattice parameters of the ZrO 2 -type solid solutions decreased with increasing Al 3+ content up to ∼10 mol%, whereas above 10 mol%, further increase of the Al 3+ content has very small influence on the unit-cell volume of both HfO 2 - and ZrO 2 -type solid solutions. The reason for such behaviour was discussed. The solubility of Hf 4+ and Zr 4+ ions in the aluminium oxides lattice appeared to be negligible

  14. Draft revision of human factors guideline HF-010

    International Nuclear Information System (INIS)

    Lee, Hyun Chul; Lee, Yong Hee; Oh, In Seok; Lee, Jung Woon; Cha, Woo Chang; Lee, Dhong Ha

    2003-05-01

    The Application of Human Factors to the design of Man-Machine Interfaces System(MMIS) in the nuclear power plant is essential to the safety and productivity of the nuclear power plants, human factors standards and guidelines as well as human factors analysis methods and experiments are weightily used to the design application. A Korean engineering company has developed a human factors engineering guideline, so-call HF-010, and has used it for human factors design, however the revision of HF-010 is necessary owing to lack of the contents related to the advanced MMI(Man-Machine Interfaces). As the results of the reviews of HF-010, it is found out that the revision of Section 9. Computer Displays of HF-010 is urgent, thus the revision was drafted on the basis of integrated human factors design guidelines for VDT, human factors design guidelines for PMAS SPADES display, human factors design guidelines for PMAS alarm display, and human factors design guidelines for electronic displays developed by the surveillance and operation support project of KOICS. The draft revision of HF-010 Section 9 proposed in this report can be utilized for the human factors design of the advanced MMI, and the high practical usability of the draft can be kept up through the continuous revision according to the advancement of digital technology

  15. Stabilization effect of a strong HF electrical field on beam-plasma interaction in a relativistic plasma waveguide

    International Nuclear Information System (INIS)

    El-Shorbagy, K.H.

    2000-07-01

    The influence effect of a strong HF electrical field on the excitation of surface waves by an electron beam under the development of instability of low-density electron beam passing through plane relativistic plasma is investigated. Starting from the two fluid plasma model we separate the problem into two parts. The 'temporal' (dynamical) part enables us to find the frequencies and growth rates of unstable waves. This part within the redefinition of natural (eigen) frequencies coincide with the system describing HF suppression of the Buneman instability in a uniform unbounded plasma. Natural frequencies of oscillations and spatial distribution of the amplitude of the self-consistent electrical field are obtained by solving a boundary value problem ('spatial' part) considering a specific spatial distribution of plasma density. Plasma electrons are considered to have a relativistic velocity. It is shown that a HF electric field has no essential influence on dispersion characteristics of unstable surface waves excited in a relativistic plasma waveguide by a low-density electron beam. The region of instability only slightly narrowing and the growth rate decreases by a small parameter and this result has been reduced compared to nonrelativistic plasma. Also, it is found that the plasma electrons have not affected the solution of the space part of the problem. (author)

  16. Students’ misconceptions on solubility equilibrium

    Science.gov (United States)

    Setiowati, H.; Utomo, S. B.; Ashadi

    2018-05-01

    This study investigated the students’ misconceptions of the solubility equilibrium. The participants of the study consisted of 164 students who were in the science class of second year high school. Instrument used is two-tier diagnostic test consisting of 15 items. Responses were marked and coded into four categories: understanding, misconception, understand little without misconception, and not understanding. Semi-structured interviews were carried out with 45 students according to their written responses which reflected different perspectives, to obtain a more elaborated source of data. Data collected from multiple methods were analyzed qualitatively and quantitatively. Based on the data analysis showed that the students misconceptions in all areas in solubility equilibrium. They had more misconceptions such as in the relation of solubility and solubility product, common-ion effect and pH in solubility, and precipitation concept.

  17. On the americium oxalate solubility

    International Nuclear Information System (INIS)

    Zakolupin, S.A.; Korablin, Eh.V.

    1977-01-01

    The americium oxalate solubility at different nitric (0.0-1 M) and oxalic (0.0-0.4 M) acid concentrations was investigated in the temperature range from 14 to 60 deg C. The dependence of americium oxalate solubility on the oxalic acid concentration was determined. Increasing oxalic acid concentration was found to reduce the americium oxalate solubility. The dependence of americium oxalate solubility on the oxalic acid concentration was noted to be a minimum at low acidity (0.1-0.3 M nitric acid). This is most likely due to Am(C 2 O 4 ) + , Am(C 2 O 4 ) 2 - and Am(C 2 O 4 ) 3 3- complex ion formation which have different unstability constants. On the basis of the data obtained, a preliminary estimate was carried out for the product of americium oxalate solubility in nitric acid medium (10 -29 -10 -31 ) and of the one in water (6.4x10 -20 )

  18. First results from the Blackstone HF radar in support of THEMIS

    Science.gov (United States)

    Lester, M.; Ruohoniemi, J. M.; Baker, J. B.; Barnes, R. J.; Clauer, C. R.; Greenwald, R. A.; Grocott, A.; Milan, S. E.; Yeoman, T. K.

    2008-12-01

    A new HF radar has been constructed and built in Blackstone, VA, as part of the SuperDARN/StormDARN programme specifically with the purpose of providing coverage over the Canadian ground sector in THEMIS. The new radar began operations in February 2008, an optimum time to support the first THEMIS tail campaign. This paper will discuss the importance of having radars at lower latitudes than the auroral zone locations of SuperDARN for substorm studies. Furthermore, the paper will also present the first results from this radar together with other SuperDARN observations during the THEMIS tail period.

  19. Centrifugal stretching along the ground state band of 168Hf

    International Nuclear Information System (INIS)

    Costin, A.; Pietralla, N.; Reese, M.; Moeller, O.; Ai, H.; Casten, R. F.; Heinz, A.; McCutchan, E. A.; Meyer, D. A.; Qian, J.; Werner, V.; Dusling, K.; Fitzpatrick, C. R.; Guerdal, G.; Petkov, P.; Rainovski, G.

    2009-01-01

    The lifetimes of the J π =4 + , 6 + , 8 + , and 10 + levels along the ground state band in 168 Hf were measured by means of the recoil distance Doppler shift (RDDS) method using the New Yale Plunger Device (NYPD) and the SPEEDY detection array at Wright Nuclear Structure Laboratory of Yale University. Excited states in 168 Hf were populated using the 124 Sn( 48 Ti,4n) fusion evaporation reaction. The new lifetime values are sufficiently precise to clearly prove the increase of quadrupole deformation as a function of angular momentum in the deformed nucleus 168 Hf. The data agree with the predictions from the geometrical confined β-soft (CBS) rotor model that involves centrifugal stretching in a soft potential

  20. Densification and properties of HfB2 based materials

    International Nuclear Information System (INIS)

    Sonber, J.K.; Ch Murthy, T.S.R.; Bedse, R.D.; Subramanian, C.; Kumar, Sunil; Fotedar, R.K.; Krishnamurthy, N.; Suri, A.K.

    2011-01-01

    This paper presents the results of investigation carried out on densification and properties of HfB 2 based materials. Densification study of HfB 2 with and without sinter additive was carried out by hot pressing. TiSi 2 and CrSi 2 were used as sinter additive. Monolithic HfB 2 was densified to only 80%ρ th at 1850 deg C with a pressure of 35 MPa. Addition of 10 wt% TiSi 2 resulted in a density of 95% TD at a relatively low temperature of 1650 deg C and a low pressure of 20 MPa. Addition of 10% CrSi 2 resulted in a density of 99% TD at the same operating conditions. All the samples were characterized by SEM/EDS and mechanical property measurement. (author)

  1. Review of speciation and solubility of radionuclides in the near and far field. Pt. 2

    International Nuclear Information System (INIS)

    Smith-Briggs, J.L.

    1992-01-01

    This report represents Part 2 in a series of three reports which review the speciation and solubility of radionuclides in the near and far field. Part 2 is a general bibliography from 1978 to 1991. This report contains the bibliography for the review of speciation and solubility radionuclides in the near and far field from 1978 to 1991. The importance of the solubility and speciation of radionuclides in relation to the safety assessment of the repository is discussed. Solubility is defined, both theoretically and pragmatically, and the factors which influence solubility and speciation are discussed. The literature search was performed using the INIS database. The UKAEA RECAP database, the NIREX report bibliography and a list of DOE reports provided by the DOE were also used. The bibliography is divided into five sections, solubility and speciation experimental data, basic thermodynamic data, solubility limiting solid phases, experimental design and review and overview articles. Some references appear in more than one section. (Author)

  2. HF-START: A Regional Radio Propagation Simulator

    Science.gov (United States)

    Hozumi, K.; Maruyama, T.; Saito, S.; Nakata, H.; Rougerie, S.; Yokoyama, T.; Jin, H.; Tsugawa, T.; Ishii, M.

    2017-12-01

    HF-START (HF Simulator Targeting for All-users' Regional Telecommunications) is a user-friendly simulator developed to meet the needs of space weather users. Prediction of communications failure due to space weather disturbances is of high priority. Space weather users from various backgrounds with high economic impact, i.e. airlines, telecommunication companies, GPS-related companies, insurance companies, international amateur radio union, etc., recently increase. Space weather information provided by Space Weather Information Center of NICT is, however, too professional to be understood and effectively used by the users. To overcome this issue, I try to translate the research level data to the user level data based on users' needs and provide an immediate usable data. HF-START is positioned to be a space weather product out of laboratory based truly on users' needs. It is originally for radio waves in HF band (3-30 MHz) but higher frequencies up to L band are planned to be covered. Regional ionospheric data in Japan and southeast Asia are employed as a reflector of skywave mode propagation. GAIA (Ground-to-topside model of Atmosphere and Ionosphere for Aeronomy) model will be used as ionospheric input for global simulation. To evaluate HF-START, an evaluation campaign for Japan region will be launched in coming months. If the campaign successes, it will be expanded to southeast Asia region as well. The final goal of HF-START is to provide the near-realtime necessary radio parameters as well as the warning message of radio communications failure to the radio and space weather users.

  3. Oxidation behavior of Hf-modified platinum aluminide coatings during thermal cycling

    Directory of Open Access Journals (Sweden)

    Liya Ye

    2018-02-01

    Full Text Available Platinum aluminide coatings with different Hf contents were fabricated by using HfCl4. The oxidation kinetics and the rumpling behavior of oxide scale were investigated. After thermal cycling, the coating with 0.46 wt% Hf showed least weight gain. With the increase of Hf content, rumpling extent of the scale decreased. Meanwhile, HfO2 preferentially formed in the scale resulting in the increase of scale thickness. The oxidation of excessive Hf even caused the spallation of the scale. The results in the present study indicate that although Hf plays an important role in decreasing rumpling extent of TGO, the oxidation of Hf decreases the adhesion of the scale. Keywords: Pt-Al coating, Hf, Oxidation, Rumpling

  4. European coordination for coastal HF radar data in EMODnet Physics

    Science.gov (United States)

    Mader, Julien; Novellino, Antonio; Gorringe, Patrick; Griffa, Annalisa; Schulz-Stellenfleth, Johannes; Montero, Pedro; Montovani, Carlo; Ayensa, Garbi; Vila, Begoña; Rubio, Anna; Sagarminaga, Yolanda

    2015-04-01

    Historically, joint effort has been put on observing open ocean, organizing, homogenizing, sharing and reinforcing the impact of the acquired information based on one technology: ARGO with profilers Argo floats, EuroSites, ESONET-NoE, FixO3 for deep water platforms, Ferrybox for stations in ships of opportunities, and GROOM for the more recent gliders. This kind of networking creates synergies and makes easier the implementation of this source of data in the European Data exchange services like EMODnet, ROOSs portals, or any applied services in the Blue economy. One main targeted improvement in the second phase of EMODnet projects is the assembling of data along coastline. In that sense, further coordination is recommended between platform operators around a specific technology in order to make easier the implementation of the data in the platforms (4th EuroGOOS DATAMEQ WG). HF radar is today recognized internationally as a cost-effective solution to provide high spatial and temporal resolution current maps (depending on the instrument operation frequency, covering from a few kilometres offshore up to 200 km) that are needed for many applications for issues related to ocean surface drift or sea state characterization. Significant heterogeneity still exists in Europe concerning technological configurations, data processing, quality standards and data availability. This makes more difficult the development of a significant network for achieving the needed accessibility to HF Radar data for a pan European use. EuroGOOS took the initiative to lead and coordinate activities within the various observation platforms by establishing a number of Ocean Observing Task Teams such as HF-Radars. The purpose is to coordinate and join the technological, scientific and operational HF radar communities at European level. The goal of the group is on the harmonization of systems requirements, systems design, data quality, improvement and proof of the readiness and standardization of

  5. HF-induced airglow at magnetic zenith: theoretical considerations

    Directory of Open Access Journals (Sweden)

    E. V. Mishin

    2005-01-01

    Full Text Available Observations of airglow at 630nm (red line and 557.7nm (green line during HF modification experiments at the High Frequency Active Auroral Research Program (HAARP heating facility are analyzed. We propose a theoretical framework for understanding the generation of Langmuir and ion acoustic waves during magnetic zenith injections. We show that observations of HF-induced airglow in an underdense ionosphere as well as a decrease in the height of the emitting volume are consistent with this scenario.

  6. Assessment of the structural relations between the bcc and omega phases of Ti, Zr, Hf and other transition metals

    International Nuclear Information System (INIS)

    Aurelio, G.; Guillermet, A.F.

    2000-01-01

    The name omega (Ω) phase refers to a high-pressure structural modification of the transition metals (TMs) Ti, Zr, and Hf. In alloys of Ti, Zr and Hf with other TMs, the Ω phase can be formed and retained metastably at room temperature by quenching the bcc structure, which is usually the stable high-temperature phase in these alloy systems. As a part of a systematic investigation of the structural and bonding properties of the bcc and Ω phases, and of the bcc → Ω phase transformation in TMs and alloys, we present in this paper a detailed analysis of the structural relations between these phases in Ti, Zr, Hf and in other TMs. The approach is as follows. First, we establish the most general geometrical relations connecting the lattice parameters and interatomic distances (IDs) of the bcc and Ω structures. Next, we focus on the ratio between the relevant IDs of these phases, which are assessed on the basis of an extensive database with experimental and theoretical information. Both stable and metastable structures are considered, and various remarkable regularities in ID ratios are discussed. Finally, in the light of the systematics of ID ratios established in the present work, a discussion is made of the probable lattice parameters for the Ω phase of Hf, which are not yet accurately known from direct measurements. (orig.)

  7. Uranium solubility and solubility controls in selected Needle's Eye groundwaters

    International Nuclear Information System (INIS)

    Falck, W.E.; Hooker, P.J.

    1991-01-01

    The solubility control of uranium in selected groundwater samples from the cliff and sediments at the Needle's Eye natural analogue site is investigated using the speciation code PHREEQE and the CHEMVAL thermodynamic database (release 3). Alkali-earth bearing uranyl carbonate secondary minerals are likely to exert influence on the solubility . Other candidates are UO 2 and arsenates, depending on the prevailing redox conditions. In the absence of literature data, solubility products for important arsenates have been estimated from analogy with other arsenates and phosphates. Phosphates themselves are unlikely to exert control owing to their comparatively high solubilities. The influence of seawater flooding into the sediments is also discussed. The importance of uranyl arsenates in the retardation of uranium in shallow sediments has been demonstrated in theory, but there are some significant gaps in the thermodynamic databases used. (author)

  8. Noble gases solubility in water

    International Nuclear Information System (INIS)

    Crovetto, Rosa; Fernandez Prini, Roberto.

    1980-07-01

    The available experimental data of solubility of noble gases in water for temperatures smaller than 330 0 C have been critically surveyed. Due to the unique structure of the solvent, the solubility of noble gases in water decreases with temperature passing through a temperature of minimum solubility which is different for each gas, and then increases at higher temperatures. As aresult of the analysis of the experimental data and of the features of the solute-solvent interaction, a generalized equation is proposed which enables thecalculation of Henry's coefficient at different temperatures for all noble gases. (author) [es

  9. 40 CFR Table 9 to Subpart Ggg of... - Default Biorates for Soluble HAP

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Default Biorates for Soluble HAP 9 Table 9 to Subpart GGG of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED... Subpart GGG of Part 63—Default Biorates for Soluble HAP Compound name Biorate (K1),L/g MLVSS-hr...

  10. Design for the sacubitril/valsartan (LCZ696) compared with enalapril study of pediatric patients with heart failure due to systemic left ventricle systolic dysfunction (PANORAMA-HF study).

    Science.gov (United States)

    Shaddy, Robert; Canter, Charles; Halnon, Nancy; Kochilas, Lazaros; Rossano, Joseph; Bonnet, Damien; Bush, Christopher; Zhao, Ziqiang; Kantor, Paul; Burch, Michael; Chen, Fabian

    2017-11-01

    Sacubitril/valsartan (LCZ696) is an angiotensin receptor neprilysin inhibitor approved for the treatment of adult heart failure (HF); however, the benefit of sacubitril/valsartan in pediatric HF patients is unknown. This global multi-center study will use an adaptive, seamless two-part design. Part 1 will assess the pharmacokinetics/pharmacodynamics of single ascending doses of sacubitril/valsartan in pediatric (1 month to sacubitril/valsartan or enalapril. A novel global rank primary endpoint derived by ranking patients (worst-to-best outcome) based on clinical events such as death, initiation of mechanical life support, listing for urgent heart transplant, worsening HF, measures of functional capacity (NYHA/Ross scores), and patient-reported HF symptoms will be used to assess efficacy. The PANORAMA-HF study, which will be the largest prospective pediatric HF trial conducted to date and the first to use a global rank primary endpoint, will determine whether sacubitril/valsartan is superior to enalapril for treatment of pediatric HF patients with reduced systemic left ventricular systolic function. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

  11. Influence of rotation on multiphoton processes in HF

    International Nuclear Information System (INIS)

    Broeckhove, J.; Feyen, B.; Van Leuven, P.

    1994-01-01

    In this contribution, the authors are concerned with the role of rotational motion in multiphoton processes induced by a laser field of high intensity. The authors use the pseudospectral split operator method for the propagation of the quantum wave-function. The rotation is treated by decomposition of the HF wave-function in its angular momentum components

  12. lambda-3, Sandia's 100-J HF laser system

    International Nuclear Information System (INIS)

    Klein, R.A.

    1979-09-01

    Sandia's lambda-geometry intermediate electron-beam-initiated HF amplifier is described in sufficient detail such that a similar system could be designed, constructed and characterized. Items included are the design of the laser cell, magnetic field design and measurements, electron-beam calorimetry, and typical laser results

  13. Multiple excitation modes in 163Hf

    DEFF Research Database (Denmark)

    Yadav, Rachita; Ma, J.C.; Marsh, J.C.

    2014-01-01

    Excited states of Hf163 were populated using the Zr94(Ge74,5n) reaction and the decay γ rays were measured with the Gammasphere spectrometer. Two previously known bands were extended to higher spins, and nine new bands were identified. In addition to bands associated with three- and five-quasiparticle...

  14. COPD predicts mortality in HF: the Norwegian Heart Failure Registry.

    Science.gov (United States)

    De Blois, Jonathan; Simard, Serge; Atar, Dan; Agewall, Stefan

    2010-03-01

    Chronic obstructive pulmonary disease (COPD) and chronic heart failure (HF) are common clinical conditions that share tobacco as a risk factor. Our aim was to evaluate the prognostic impact of COPD on HF patients. The Norwegian Heart Failure Registry was used. The study included 4132 HF patients (COPD, n = 699) from 22 hospitals (mean follow-up, 13.3 months). COPD patients were older, more often smokers and diabetics, less often on beta-blockers and had a higher heart rate. They were more often in New York Heart Association (NYHA) Class III or IV (COPD, 63%; no COPD, 51%), although left ventricular ejection fraction (LVEF) distribution was similar. COPD independently predicted death (adjusted hazard ratio [HR], 1.188; 95% CI: 1.015 to 1.391; P = 0.03) along with age, creatinine, NYHA Class III/IV (HR, 1.464; 95% CI: 1.286 to 1.667) and diabetes. beta-blockers at baseline were associated with improved survival in patients with LVEF < or =40% independently of COPD. COPD is associated with a poorer survival in HF patients. COPD patients are overrated in terms of NYHA class in comparison with patients with similar LVEF. Nonetheless, NYHA class remains the strongest predictor of death in these patients. Copyright (c) 2010 Elsevier Inc. All rights reserved.

  15. Research of HF and HV circuit with Pspice

    International Nuclear Information System (INIS)

    Guo Jianjiang; Li Quanfeng; Zheng Shuxin; Li Wenjun; Tang Chuanxiang

    2005-01-01

    Transferring HF and HV pulse with 3 kinds of components is discussed. Terminal volt waves was got using the soft of Pspice when transmission line is matching of load in 3 kinds of condition. It is proved by experiments that the results got from Pspice have important values to improve experiment circuit. (authors)

  16. Mechanisms for oral absorption of poorly water-soluble compounds

    DEFF Research Database (Denmark)

    Lind, Marianne Ladegaard

    Abstract A large part of the new drug candidates discovered by the pharmaceutical industry have poor solubility in aqueous media. The preferred route of drug administration is the oral route, but for these poorly water-soluble drug candidates the oral bioavailability can be low and variable. Often......, phospholipids) and exogenous surfactants used in pharmaceutical formulations on the oral absorption of poorly water-soluble drug substances. Three different models were used for this purpose. The first model was the in vitro Caco-2 cell model. Simulated intestinal fluids which did not decrease cellular...... products are important for the solubilization of poorly water-soluble drug substances and thus absorption. The second model used was the lipoprotein secreting Caco-2 cell model, which was used to simulate intestinal lymphatic transport in vitro. Various simulated intestinal fluids were composed...

  17. Solubility of gases in water at high temperature

    International Nuclear Information System (INIS)

    Crovetto, Rosa; Fernandez Prini, R.J.; Japas, M.L.

    1981-01-01

    In the primary circuits of the PWR, it is usual to find apolar gases such as the noble gases like, nitrogen, hydrogen (deuterium) and oxygen. These gases enter into the circuit partly due to failures in the fuel elements, accidental entries of air into the system and corrosion processes and radiolisis in the coolant media. For the operation of several auxiliary systems in the primary circuit, it is important to know the solubility of these gases in the flux of the circuit and the evaluation of physicochemical processes that take place. A cell has been built that allows to carry out determinations of solubility in the range of 350 deg C and 100 Mega Pascal. Three alternative experimental techniques have been developed to determine the solubility of the gases which are compared to each other. Measures of solubility of argon in H2O and D2O have been made in a wide range of temperatures. (V.B.) [es

  18. Pure Phase Solubility Limits: LANL

    International Nuclear Information System (INIS)

    C. Stockman

    2001-01-01

    The natural and engineered system at Yucca Mountain (YM) defines the site-specific conditions under which one must determine to what extent the engineered and the natural geochemical barriers will prevent the release of radioactive material from the repository. Most important mechanisms for retention or enhancement of radionuclide transport include precipitation or co-precipitation of radionuclide-bearing solid phases (solubility limits), complexation in solution, sorption onto surfaces, colloid formation, and diffusion. There may be many scenarios that could affect the near-field environment, creating chemical conditions more aggressive than the conditions presented by the unperturbed system (such as pH changes beyond the range of 6 to 9 or significant changes in the ionic strength of infiltrated waters). For an extended period of time, the near-field water composition may be quite different and more extreme in pH, ionic strength, and CO 2 partial pressure (or carbonate concentration) than waters at some distance from the repository. Reducing conditions, high pH (up to 11), and low carbonate concentration may be present in the near-field after reaction of infiltrating groundwater with engineered barrier systems, such as cementitious materials. In the far-field, conditions are controlled by the rock-mass buffer providing a near-neutral, oxidizing, low-ionic-strength environment that controls radionuclide solubility limits and sorption capacities. There is the need for characterization of variable chemical conditions that affect solubility, speciation, and sorption reactions. Modeling of the groundwater chemistry is required and leads to an understanding of solubility and speciation of the important radionuclides. Because experimental studies cannot be performed under the numerous potential chemical conditions, solubility limitations must rely on geochemical modeling of the radionuclide's chemistry. Fundamental thermodynamic properties, such as solubility products

  19. Pure Phase Solubility Limits: LANL

    Energy Technology Data Exchange (ETDEWEB)

    C. Stockman

    2001-01-26

    The natural and engineered system at Yucca Mountain (YM) defines the site-specific conditions under which one must determine to what extent the engineered and the natural geochemical barriers will prevent the release of radioactive material from the repository. Most important mechanisms for retention or enhancement of radionuclide transport include precipitation or co-precipitation of radionuclide-bearing solid phases (solubility limits), complexation in solution, sorption onto surfaces, colloid formation, and diffusion. There may be many scenarios that could affect the near-field environment, creating chemical conditions more aggressive than the conditions presented by the unperturbed system (such as pH changes beyond the range of 6 to 9 or significant changes in the ionic strength of infiltrated waters). For an extended period of time, the near-field water composition may be quite different and more extreme in pH, ionic strength, and CO{sub 2} partial pressure (or carbonate concentration) than waters at some distance from the repository. Reducing conditions, high pH (up to 11), and low carbonate concentration may be present in the near-field after reaction of infiltrating groundwater with engineered barrier systems, such as cementitious materials. In the far-field, conditions are controlled by the rock-mass buffer providing a near-neutral, oxidizing, low-ionic-strength environment that controls radionuclide solubility limits and sorption capacities. There is the need for characterization of variable chemical conditions that affect solubility, speciation, and sorption reactions. Modeling of the groundwater chemistry is required and leads to an understanding of solubility and speciation of the important radionuclides. Because experimental studies cannot be performed under the numerous potential chemical conditions, solubility limitations must rely on geochemical modeling of the radionuclide's chemistry. Fundamental thermodynamic properties, such as solubility

  20. Binary systems solubilities of inorganic and organic compounds

    CERN Document Server

    Stephen, H

    1963-01-01

    Solubilities of Inorganic and Organic Compounds, Volume 1: Binary Systems, Part 1 is part of an approximately 5,500-page manual containing a selection from the International Chemical Literature on the Solubilities of Elements, Inorganic Compounds, Metallo-organic and Organic Compounds in Binary, Ternary and Multi-component Systems. A careful survey of the literature in all languages by a panel of scientists specially appointed for the task by the U.S.S.R. Academy of Sciences, Moscow, has made the compilation of this work possible. The complete English edition in five separately bound volumes w

  1. Nanosized Hydroxyapatite Precipitation on the Ti—30Ta—xHf Alloys.

    Science.gov (United States)

    Lee, Kang; Jang, Jae- In; Han-Cheol, Choe

    2017-04-01

    In this study, we prepared hydroxyapatite (HAp) layer on the alkali treated Ti–30Ta–xHf alloys using electrochemical deposition method. Ti–30Ta–xHf alloys was anodized in 5 M NaOH solution at 0.3 A for 10 min. Alkali treated Ti–30Ta–xHf surface formed by anodization step which acted as templates and anchorage for growth of the HAp during subsequent pulsed electrochemical deposition process at 85 °C. The phase and morphologies of deposited HAp layer were affected by the Hf contents of Ti–30Ta–xHf alloys. The nano-scale rod-like HAp layer was formed on untreated Ti–30Ta–xHf alloys with partially low crystallinity. In the case of alkali treated Ti–30Ta–xHf, nano-sized needle-like layers were transferred to nano-flake surface and denser morphology as Hf content increased.

  2. HF Radar observations of the Dardanelles outflow current in North Eastern Aegean using validated WERA HF radar data

    Directory of Open Access Journals (Sweden)

    Z. KOKKINI

    2014-12-01

    Full Text Available A two-site WERA HF radar station was installed in November 2009 at the eastern coast of Lemnos Island in North Aegean Sea, aiming to monitor the surface inflow of Black Sea waters exiting from the Dardanelles Strait, as well as to constitute a coastal management tool for incidents of oil-pollution or save-and-rescue operations. Strong interference by foreign transmissions is a source of noise deteriorating the quality of the backscattered signal, thus significantly reducing the HF radar’s effective data return rate. In order to ameliorate this problem, further quality-control and data gap interpolating procedures have been developed and applied, to be used in addition to the procedures incorporated and used by the manufacturer’s signal processing software. The second-level processing involves traditional despiking in the temporal domain, preceding Empirical Orthogonal Function analysis. The latter is used not only to filter high-frequency noise but also to fill data gaps in time and space. The data reconstruction procedure has been assessed via comparison of (a HF radial with CODE-type drifter radial velocities as well as (b HF-derived virtual drifter tracks with actual drifter tracks. The main circulation features and their variability, as revealed by the reconstructed fields, are presented.

  3. Cátions hidrossolúveis na parte aérea de culturas anuais mediante aplicação de calcário e gesso em superfície Water-soluble cations in shoots of annual crops as affected by lime and phosphogypsum surface application

    Directory of Open Access Journals (Sweden)

    Rogério Peres Soratto

    2007-02-01

    Full Text Available A eficiência da calagem superficial pode ser melhorada por meio de compostos orgânicos hidrossolúveis liberados por resíduos vegetais. No entanto, não se sabe se os teores desses compostos nos resíduos das culturas podem ser modificados pela aplicação de calcário e gesso em superfície. O presente trabalho objetivou avaliar os efeitos das aplicações de calcário e gesso em superfície sobre os teores de cátions solúveis nos resíduos vegetais das culturas de arroz, feijão e aveia-preta. O experimento foi realizado em um Latossolo Vermelho distroférrico de Botucatu (SP. O delineamento foi de blocos casualizados com parcelas subdivididas e quatro repetições. As parcelas foram constituídas por quatro doses de calcário dolomítico (0, 1.100, 2.700 e 4.300 kg ha-1 e as subparcelas, pela aplicação ou não de 2.100 kg ha-1 de gesso agrícola. Para as culturas de verão foi utilizado esquema de parcela subsubdividida. As subsubparcelas foram constituídas por dois cultivares de arroz de terras altas (Caiapó e IAC 202, no ano agrícola 2002/03, e dois cultivares de feijão (Pérola e Carioca, em 2003/04. A aveia-preta foi cultivada no inverno dos dois anos, utilizando apenas o cultivar Comum. Os teores de cátions solúveis na parte aérea das culturas de arroz, feijão e aveia-preta foram alterados pela aplicação de calcário e gesso em superfície. A gessagem em superfície aumentou os teores solúveis de Ca e reduziu o de Mg na parte aérea das culturas, principalmente nas primeiras safras após a aplicação. A calagem aumentou os teores de cátions solúveis na parte aérea de todas as culturas. As culturas do feijão e da aveia-preta apresentaram maiores teores de cátions solúveis nos resíduos da parte aérea, avaliados no florescimento.Surface liming efficiency can be increased through water-soluble organic compounds released by plant residues. However, it is unknown if the contents of these compounds in crop residues

  4. Nanotube formation and morphology change of Ti alloys containing Hf for dental materials use

    International Nuclear Information System (INIS)

    Jeong, Yong-Hoon; Lee, Kang; Choe, Han-Cheol; Ko, Yeong-Mu; Brantley, William A.

    2009-01-01

    In this paper, Ti-Hf (10, 20, 30 and 40 wt.%) alloys were prepared by arc melting, and subjected to heat treatment for 24 h at 1000 o C in an argon atmosphere. Formation of surface nanotubes was achieved by anodizing a Ti-Hf alloy in 1.0 M H 3 PO 4 electrolytes with small amounts of NaF at room temperature. Microstructures of the alloys and nanotube morphology were examined by field-emission scanning electron microscopy (FE-SEM) and X-ray diffraction (XRD). The homogenized Ti-Hf alloys had a needle-like microstructure of α phase, and nanotubes formed on Ti-xHf alloys had the anatase phase after treatment that promoted crystallization. Uniform nanotubes formed for Hf contents up to 20 wt.%. Irregular nanotubes formed on the Ti-30Hf and Ti-40Hf alloys. The structure of the irregular layers on the Ti-30Hf and Ti-40Hf alloys had nanotubes of two sizes. Increasing the Hf content in Ti led to the formation of nanotubes with more narrow size. The pores in the nanotubes typically had a diameter ranging from 80-120 nm and a length of approximately 1.7 μm. It is concluded that nanotube morphology on Ti-Hf alloys can controlled by varying the amount of Hf.

  5. 40 CFR 180.1273 - Beauveria bassiana HF23; exemption from the requirement of a tolerance.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Beauveria bassiana HF23; exemption... FOOD Exemptions From Tolerances § 180.1273 Beauveria bassiana HF23; exemption from the requirement of a tolerance. Residues of Beauveria bassiana HF23 are exempt from the requirement of a tolerance on all food...

  6. Photon strength function in the Hf-181 nucleus by method of two-step cascade

    International Nuclear Information System (INIS)

    Le Hong Khiem

    2003-01-01

    The applicability of sum-coincidence measurements of two-step cascade gamma ray spectra determining Photon Strength Function (PSF) of Hf-181 induced from Hf-180 (n,2γ) Hf-181 reaction is presented. Up to 80% intensity of the primary gamma ray transitions in a wide energy range have been deduced and compared to model calculation. (author)

  7. Action mechanism of hydrogen gas on deposition of HfC coating using HfCl{sub 4}-CH{sub 4}-H{sub 2}-Ar system

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Yalei, E-mail: yaleipm@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, 410083 (China); School of Metallurgy and Environment, Central South University, Changsha, 410083 (China); Li, Zehao [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, 410083 (China); Xiong, Xiang, E-mail: xiongx@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, 410083 (China); Li, Xiaobin [School of Metallurgy and Environment, Central South University, Changsha, 410083 (China); Chen, Zhaoke; Sun, Wei [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, 410083 (China)

    2016-12-30

    Highlights: • HfC coatings were deposited on C/C composites by LPCVD using HfCl4-CH4-H2-Ar system. • Action mechanism of H2 on structure and growth behavior of HfC coating was studied. • Increased H2 concentration leads to transformation in growth mechanism of coating. - Abstract: Hafnium carbide coatings were deposited on carbon/carbon composites by low pressure chemical vapor deposition using HfCl{sub 4}-CH{sub 4}-H{sub 2}-Ar system. The microstructure, mechanical and ablation resistance performance of HfC coatings deposited with various H{sub 2} concentrations were investigated. The effect of hydrogen gas on the deposition of HfC coating was also discussed. Results show that all of the deposited coatings are composed of single cubic HfC phase, the hydrogen gas acted as a crucial role in determining the preferred orientation, microstructure and growth behavior of HfC coatings. During the deposition process, the gas phase supersaturation of the reaction species can be controlled by adjusting the hydrogen gas concentration. When deposited with low hydrogen gas concentration, the coating growth was dominated by the nucleation of HfC, which results in the particle-stacked structure of HfC coating. Otherwise, the coating growth was dominated by the crystal growth at high hydrogen gas concentration, which leads to the column-arranged structure of HfC coating. Under the ablation environment, the coating C2 exhibits better configurational stability and ablation resistance. The coating structure has a significant influence on the mechanical and ablation resistance properties of HfC coating.

  8. Superacid Catalyzed Depolymerization and Conversion of Coals. Final Technical Report. [HF:BF{sub 2}/H{sub 2}

    Science.gov (United States)

    Olah, G.

    1980-01-01

    We were interested in applying superacid catalyzed cleavage-depolymerization and ionic hydrogenation low temperature conversion of coal to liquid hydrocarbon, as well as obtaining information about the reactions involved and the structure of intermediates of the coal liquefaction process. In order to show the feasibility of our proposed research we have carried out preliminary investigation in these areas. Preceding our work there was no practical application of a superacid system to coal liquefaction. We carried out an extensive study of the potential of the HF:BF{sub 3}/H{sub 2} system for coal hydroliquefaction. Under varying conditions of reactant ratio, reaction time and temperature, we were able to obtain over 95% pyridine extractible product by treating coal in HF:BF{sub 3}:H{sub 2} system at approx. 100 degrees C for 4 hours. The coal to acid ratio was 1:5 and FB{sub 3} at 900 psi and H{sub 2} at 500 psi were used. These are extremely encouraging results in that the conditions used are drastically milder than those used in any known process, such as Exxon donor solvent and related processes. The cyclohexane extractibility of the treated coal was as high as 27% and the yield of liquid distillate at 400 degrees C/5 x 10{sup -3}/sup torr/ was approx. 30%. The infrared spectrum of product coal, extracts and distillates were distinctly different from the starting coal and show a significant increase in the amount of saturates. The {sup 1}H NMR spectrum of cyclohexane extract of the treated coal shows essentially all aliphatic photons. The spectra of other treated coal extracts show increased amounts and types of aliphatic protons as well as significant amounts of protons bound to unsaturated sites. This again indicates that the HF-BF{sub 3} system is depolymerizing the coal to small fragments which are soluble in non-polar solvents.

  9. Effects of substrate temperature on the structure and mechanical properties of (TiVCrZrHf)N coatings

    Energy Technology Data Exchange (ETDEWEB)

    Liang, Shih-Chang [Department of Materials Science and Engineering, National Chung Hsing University, Taichung 402, Taiwan (China); Chang, Zue-Chin [Department of Mechanical Engineering, National Chin-Yi University of Technology, Taichung 411, Taiwan (China); Tsai, Du-Cheng [Department of Materials Science and Engineering, National Chung Hsing University, Taichung 402, Taiwan (China); Lin, Yi-Chen; Sung, Huan-Shin [Department of Mechanical Engineering, National Chin-Yi University of Technology, Taichung 411, Taiwan (China); Deng, Min-Jen [Department of Materials Science and Engineering, National Chung Hsing University, Taichung 402, Taiwan (China); Department of Optometry, Jen-Teh Junior College of Medicine, Nursing and Management, Miaoli County 356, Taiwan (China); Shieu, Fuh-Sheng, E-mail: fsshieu@dragon.nchu.edu.tw [Department of Materials Science and Engineering, National Chung Hsing University, Taichung 402, Taiwan (China)

    2011-06-15

    The present paper reports the influence of growth conditions on the characteristics of (TiVCrZrHf)N films prepared by rf reactive magnetron sputtering at various substrate temperatures. The nitrogen content is observed to decrease with increasing substrate temperature. The X-ray diffraction results indicate that all (TiVCrZrHf)N films are simple face centered cubic (FCC) structures. Initially, there is an obvious decrease followed by an increase in grain size with the increase in substrate temperature. The lower part of the microstructure has an amorphous structure. A nano grain structure (size {approx}1 nm) with a random orientation is also observed above the amorphous structure. The fully dense columnar structure with an fcc crystal phase then starts to develop. Extreme hardness of around 48 GPa is obtained in the present alloy design.

  10. Effects of substrate temperature on the structure and mechanical properties of (TiVCrZrHf)N coatings

    International Nuclear Information System (INIS)

    Liang, Shih-Chang; Chang, Zue-Chin; Tsai, Du-Cheng; Lin, Yi-Chen; Sung, Huan-Shin; Deng, Min-Jen; Shieu, Fuh-Sheng

    2011-01-01

    The present paper reports the influence of growth conditions on the characteristics of (TiVCrZrHf)N films prepared by rf reactive magnetron sputtering at various substrate temperatures. The nitrogen content is observed to decrease with increasing substrate temperature. The X-ray diffraction results indicate that all (TiVCrZrHf)N films are simple face centered cubic (FCC) structures. Initially, there is an obvious decrease followed by an increase in grain size with the increase in substrate temperature. The lower part of the microstructure has an amorphous structure. A nano grain structure (size ∼1 nm) with a random orientation is also observed above the amorphous structure. The fully dense columnar structure with an fcc crystal phase then starts to develop. Extreme hardness of around 48 GPa is obtained in the present alloy design.

  11. The solubility of carbon in low-nitrogen liquid lithium

    International Nuclear Information System (INIS)

    Yonco, R.M.; Homa, M.I.

    1986-01-01

    The solubility of carbon in liquid lithium containing 0 C and compared with the solubility in lithium containing proportional 2600 wppm nitrogen in that same temperature range. A direct sampling method was employed in which filtered samples of the saturated solution were taken at randomly selected temperatures. The entire sample was analyzed for carbon by the acetylene evolution method. The analytical method was examined critically and it was found that (1) all of the carbon in solution, including carbon introduced as lithium cyanamide is detected and (2) ethylene and ethane must also be measured and included with the acetylene to get complete recovery of the carbon content of the sample. The solubility of carbon in low-nitrogen lithium can be expressed by the equations ln S=6.731-8617T -1 and log Ssup(*)=7.459-3740T -1 , where S is the mole percent Li 2 C 2 and Ssup(*) is in weight parts per million carbon. The presence of proportional 2600 wppm nitrogen does not affect the solubility of carbon in lithium at temperatures above proportional 350 0 C, but at lower temperatures it increased the solubility by as much as an order of magnitude compared to the solubility in low-nitrogen lithium. (orig.)

  12. Effects of soluble organic complexants and their degradation products on the removal of selected radionuclides from high-level waste. Part II: Distributions of Sr, Cs, Tc, and Am onto 32 absorbers from four variations of Hanford tank 101-SY simulant solution

    International Nuclear Information System (INIS)

    Marsh, S.F.; Svitra, Z.V.; Bowen, S.M.

    1995-04-01

    Many of the radioactive waste storage tanks at U.S. Department of Energy facilities contain organic compounds that have been degraded by radiolysis and chemical reactions during decades of storage. In this second part of our three-part investigation of the effects of soluble organic complexants and their degradation products, we measured the sorption of strontium, cesium, technetium, and americium onto 32 absorbers that offer high sorption of these elements in the absence of organic complexants. The four solutions tested were (1) a simulant for a 3:1 dilution of Hanford Tank 101-SY contents that initially contained ethylenediaminetetraacetic acid (EDTA), (2) this simulant after gamma-irradiation to 34 Mrads, (3) the unirradiated simulant after treatment with a hydrothermal organic-destruction process, and (4) the irradiated simulant after hydrothermal processing. For each of 512 element/absorber/solution combinations, we measured distribution coefficients (Kds) twice for each period for dynamic contact periods of 30 min, 2 h, and 6 h to obtain information about sorption kinetics. On the basis of our 3,072 measured Kd values, the sorption of strontium and americium is significantly decreased by the organic components of the simulant solutions, whereas the sorption of cesium and technetium appears unaffected by the organic components of the simulant solutions

  13. Study on the adducts formation of Zr and Hf chelates

    International Nuclear Information System (INIS)

    Ree, Chin Taik; Jung, Young Sam; Park, Jun Kown

    1986-01-01

    The synergistic effect observed in Zr(IV) and Hf(IV) extraction from strong perchloric acid solutions by the mixtures of 2-Thenoyltri-fluoroacetone(TTA) and Octanols is shown to be caused by the formation of a mixed complex, M(TTA) 3 XS (M=Zr(IV), HF(IV), X=ClO 4 - , S=Octanol). One of the four TTA molecules coordinated at lower HClO 4 concentration to the metal as bidendate ligand seems to be changed to monodendate due to increasing HClO 4 concentration. The monodenate TTA ligand leaves the coordination site, finally, due to the activity of perchlorate at higher concentration and the additional coordination of an Octanol molecule seems to be allowed to the vaccant site which shows the synergistic extraction phenomena. (Author)

  14. The anisotropy of Hf diffusion in α-Zr

    International Nuclear Information System (INIS)

    Hood, G.M.; Zou, H.; Roy, J.A.; Schultz, R.J.; Matsuura, N.; Jackson, J.A.

    1995-07-01

    Hf diffusion coefficients (D) have been measured in the temperature interval 870-1100 K, in directions parallel (D pa ) and perpendicular (D pe ) to the c-axis of double-faced, single crystal specimens of both high-purity (HP) and nominally pure (NP) α-Zr single crystals. The diffusion profiles were measured by secondary ion mass spectrometry. Hf diffusion in HP α-Zr is characterised by an activation energy of about 3.0 eV and a pre-exponential factor of about 10 -5 m 2 /s. The anisotropy ratio, D pa /D pe is ∼ 1.0 for the NP specimens. A dependence of D on diffusion time/depth is indicated for some NP experiments on NP Zr. (author). 7 refs., 2 tabs., 3 figs

  15. First demonstration of HF-driven ionospheric currents

    Science.gov (United States)

    Papadopoulos, K.; Chang, C.-L.; Labenski, J.; Wallace, T.

    2011-10-01

    The first experimental demonstration of HF driven currents in the ionosphere at low ELF/ULF frequencies without relying in the presence of electrojets is presented. The effect was predicted by theoretical/computational means in a recent letter and given the name Ionospheric Current Drive (ICD). The effect relies on modulated F-region HF heating to generate Magneto-Sonic (MS) waves that drive Hall currents when they reach the E-region. The Hall currents inject ELF waves into the Earth-Ionosphere waveguide and helicon and Shear Alfven (SA) waves in the magnetosphere. The proof-of-concept experiments were conducted using the HAARP heater in Alaska under the BRIOCHE program. Waves between 0.1-70 Hz were measured at both near and far sites. The letter discusses the differences between ICD generated waves and those relying on modulation of electrojets.

  16. Fe substitution and pressure effects on superconductor Re6Hf

    Science.gov (United States)

    Yang, Jinhu; Guo, Yang; Wang, Hangdong; Chen, Bin

    2018-04-01

    Polycrystalline samples of (Re1-xFex) 6Hf were synthesized by arc-melting method and the phase purity of the samples was confirmed by powder X-ray diffraction method. In this paper, we report the Fe substitution and pressure effect on non-centrosymmetric superconductor Re6Hf. The superconducting transition temperature, TC, is confirmed by the measurements of magnetic susceptibility, electrical resistivity for x ≤ 0.22 samples with the temperature down to 2 K. We find that the TC is suppressed with the increase of Fe content. The upper critical field Hc2 is larger than the value predicted by the WHH theory and shows a linear temperature dependence down to 2 K. When upon the application of external pressure up to 2.5 GPa, the TC decreases monotonically at a rate dlnTC/dP of 0.01 GPa-1.

  17. Comparison between HF radar current data and moored ADCP currentmeter

    International Nuclear Information System (INIS)

    Cosoli, S.

    2005-01-01

    A preliminary assessment of accuracy of a two-sites shore-based HF Radar network along the Venice Lagoon littoral was attempted by means of comparison with a 57.5 day-long ADCP current time series for the period September-October 2002. Results showed that radar measurements were accurate ( O . The main differences between the HF radar and surface ADCP currents can be explained in terms of random errors affecting the measurement technique and the daily sea breeze forcing, since low-pass filtering of current time series significantly improved the correlation and decreased the RMS of the differences between the two measured data set. Comparison of the semidiurnal (M2, S2) tidal band suggested good agreement between tidal ellipse amplitudes. Wind forcing on a daily time-scale (sea-breeze) was associated with larger differences between radar and ADCP currents at a diurnal band due to the presence of a vertical shear in the surface layer

  18. Closed cycle high-repetition-rate pulsed HF laser

    Science.gov (United States)

    Harris, Michael R.; Morris, A. V.; Gorton, Eric K.

    1997-04-01

    The design and performance of a closed cycle high repetition rate HF laser is described. A short pulse, glow discharge is formed in a 10 SF6:1 H2 gas mixture at a total pressure of approximately 110 torr within a 15 by 0.5 by 0.5 cm3 volume. Transverse, recirculated gas flow adequate to enable repetitive operation up to 3 kHz is imposed by a centrifugal fan. The fan also forces the gas through a scrubber cell to eliminate ground state HF from the gas stream. An automated gas make-up system replenishes spent gas removed by the scrubber. Typical mean laser output powers up to 3 W can be maintained for extended periods of operation.

  19. Performance Analysis of HF Band FB-MC-SS

    Energy Technology Data Exchange (ETDEWEB)

    Hussein Moradi; Stephen Andrew Laraway; Behrouz Farhang-Boroujeny

    2016-01-01

    Abstract—In a recent paper [1] the filter bank multicarrier spread spectrum (FB-MC-SS) waveform was proposed for wideband spread spectrum HF communications. A significant benefit of this waveform is robustness against narrow and partial band interference. Simulation results in [1] demonstrated good performance in a wideband HF channel over a wide range of conditions. In this paper we present a theoretical analysis of the bit error probably for this system. Our analysis tailors the results from [2] where BER performance was analyzed for maximum ration combining systems that accounted for correlation between subcarriers and channel estimation error. Equations are give for BER that closely match the simulated performance in most situations.

  20. On nitrogen solubility in water

    International Nuclear Information System (INIS)

    Kalajda, Yu.A.; Katkov, Yu.D.; Kuznetsov, V.A.; Lastovtsev, A.Yu.; Lastochkin, A.P.; Susoev, V.S.

    1980-01-01

    Presented are the results of experimental investigations on nitrogen solubility in water under 0-15 MPa pressure, at the temperature of 100-340 deg C and nitrogen concentration of 0-5000 n.ml. N 2 /kg H 2 O. Empiric equations are derived and a diagram of nitrogen solubility in water is developed on the basis of the experimental data, as well as critically evaluated published data. The investigation results can be used in analyzing water-gas regime of a primary heat carrier in stream-generating plants with water-water reactors

  1. Preliminary considerations concerning actinide solubilities

    International Nuclear Information System (INIS)

    Newton, T.W.; Bayhurst, B.P.; Daniels, W.R.; Erdal, B.R.; Ogard, A.E.

    1980-01-01

    Work at the Los Alamos Scientific Laboratory on the fundamental solution chemistry of the actinides has thus far been confined to preliminary considerations of the problems involved in developing an understanding of the precipitation and dissolution behavior of actinide compounds under environmental conditions. Attempts have been made to calculate solubility as a function of Eh and pH using the appropriate thermodynamic data; results have been presented in terms of contour maps showing lines of constant solubility as a function of Eh and pH. Possible methods of control of the redox potential of rock-groundwater systems by the use of Eh buffers (redox couples) is presented

  2. Thorium oxalate solubility and morphology

    International Nuclear Information System (INIS)

    Monson, P.R. Jr.; Hall, R.

    1981-10-01

    Thorium was used as a stand-in for studying the solubility and precipitation of neptunium and plutonium oxalates. Thorium oxalate solubility was determined over a range of 0.001 to 10.0 in the concentration parameter [H 2 C 2 O 4 ]/[HNO 3 ] 2 . Morphology of thorium oxide made from the oxalate precipitates was characterized by scanning electron microscopy. The different morphologies found for oxalate-lean and oxalate-rich precipitations were in agreement with predictions based on precipitation theory

  3. U-Pb and Lu-Hf systematics of zircons from Sargur metasediments, Dharwar Craton, Southern India: new insights on the provenance and crustal evolution

    International Nuclear Information System (INIS)

    Maibam, Bidyananda; Gerdes, Axel; Srinivasan, R.; Goswami, J.N.

    2017-01-01

    A study of U-Pb and Lu-Hf-Yb isotope data in zircons from metamorphosed psammopelite and quartzite from the type area of Archaean Sargur Group, Dharwar Craton, India is carried out. Two age populations are observed: an older population with concordant U-Pb ages between 2.7 and 2.8 Ga, and a younger population with ages in the 2.4 - 2.6 Ga age range. The εHf values of 0 to + 2.0 for the older zircon population suggest that they were derived from juvenile crust formed at 2.7- 2.8 Ga. Sub-chondritic εHf values for the younger population indicate metamorphism and/or crustal reworking at ∼2.5 Ga. Meta-sedimentary enclaves in the Sargur type area are therefore part of the gneiss-supracrustal complex of different antiquities and may not have an independent stratigraphic status. (author)

  4. Beating HF waves to generate VLF waves in the ionosphere

    Science.gov (United States)

    Kuo, Spencer; Snyder, Arnold; Kossey, Paul; Chang, Chia-Lie; Labenski, John

    2012-03-01

    Beat-wave generation of very low frequency (VLF) waves by two HF heaters in the ionosphere is formulated theoretically and demonstrated experimentally. The heater-induced differential thermal pressure force and ponderomotive force, which dominate separately in the D and F regions of the ionosphere, drive an electron current for the VLF emission. A comparison, applying appropriate ionospheric parameters shows that the ponderomotive force dominates in beat-wave generation of VLF waves. Three experiments, one in the nighttime in the absence of D and E layers and two in the daytime in the presence of D and E layers, were performed. X mode HF heaters of slightly different frequencies were transmitted at CW full power. VLF waves at 10 frequencies ranging from 3.5 to 21.5 kHz were generated. The frequency dependencies of the daytime and nighttime radiation intensities are quite similar, but the nighttime radiation is much stronger than the daytime one at the same radiation frequency. The intensity ratio is as large as 9 dB at 11.5 kHz. An experiment directly comparing VLF waves generated by the beat-wave approach and by the amplitude modulation (AM) approach was also conducted. The results rule out the likely contribution of the AM mechanism acting on the electrojet and indicate that beat-wave in the VLF range prefers to be generated in the F region of the ionosphere through the ponderomotive nonlinearity, consistent with the theory. In the nighttime experiment, the ionosphere was underdense to the HF heaters, suggesting a likely setting for effective beat-wave generation of VLF waves by the HF heaters.

  5. Modelling of Phase Equlibria in the Hf-V System\

    Czech Academy of Sciences Publication Activity Database

    Vřešťál, Jan; Pavlů, Jana; Wdowik, U. D.; Šob, Mojmír

    2017-01-01

    Roč. 53, č. 3 (2017), s. 239-247 ISSN 1450-5339 R&D Projects: GA ČR GA14-15576S; GA MŠk(CZ) LQ1601 Institutional support: RVO:68081723 Keywords : Laves phases * Hf-V system * Ab initio calculations * Phase diagram * Zero Kelvin * CALPHAD method Subject RIV: BM - Solid Matter Physics ; Magnetism OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.) Impact factor: 0.804, year: 2016

  6. Ionizing wave via high-power HF acceleration

    OpenAIRE

    Mishin, Evgeny; Pedersen, Todd

    2010-01-01

    Recent ionospheric modification experiments with the 3.6 MW transmitter at the High Frequency Active Auroral Research Program (HAARP) facility in Alaska led to discovery of artificial ionization descending from the nominal interaction altitude in the background F-region ionosphere by ~60 km. This paper presents a physical model of an ionizing wavefront created by suprathermal electrons accelerated by the HF-excited plasma turbulence.

  7. Clinical trials update from the Heart Failure Society of America Meeting 2009: FAST, IMPROVE-HF, COACH galectin-3 substudy, HF-ACTION nuclear substudy, DAD-HF, and MARVEL-1.

    Science.gov (United States)

    Lainscak, Mitja; Coletta, Alison P; Sherwi, Nasser; Cleland, John G F

    2010-02-01

    This article presents findings and a commentary on late-breaking trials presented during the meeting of the Heart Failure Society of America in September 2009. Unpublished reports should be considered as preliminary, since analyses may change in the final publication. The FAST trial showed somewhat better performance of intrathoracic impedance for prediction of deterioration in patients with heart failure (HF) when compared with daily weighing. The IMPROVE-HF study reported the benefits of education on the management of patients with systolic HF. Galectin-3 appeared a useful method for improving risk stratification of patients with chronic HF in a substudy of the COACH trial. A nuclear substudy of the HF-ACTION trial failed to demonstrate that resting myocardial perfusion imaging, a measure of myocardial scar and viability, was clinically useful. A small randomized controlled trial (DAD-HF) suggested that the use of low-dose dopamine in patients with acutely decompensated HF was associated with less deterioration in renal function and less hypokalaemia. The MARVEL-1 trial raises further concerns about the safety of myoblast transplantation in ischaemic HF.

  8. Collision-Induced Dissociation Study of Strong Hydrogen-Bonded Cluster Ions Y-(HF) n (Y=F, O2) Using Atmospheric Pressure Corona Discharge Ionization Mass Spectrometry Combined with a HF Generator.

    Science.gov (United States)

    Sakamoto, Kenya; Sekimoto, Kanako; Takayama, Mitsuo

    2017-01-01

    Hydrogen fluoride (HF) was produced by a homemade HF generator in order to investigate the properties of strong hydrogen-bonded clusters such as (HF) n . The HF molecules were ionized in the form of complex ions associated with the negative core ions Y - produced by atmospheric pressure corona discharge ionization (APCDI). The use of APCDI in combination with the homemade HF generator led to the formation of negative-ion HF clusters Y - (HF) n (Y=F, O 2 ), where larger clusters with n ≥4 were not detected. The mechanisms for the formation of the HF, F - (HF) n , and O 2 - (HF) n species were discussed from the standpoints of the HF generator and APCDI MS. By performing energy-resolved collision-induced dissociation (CID) experiments on the cluster ions F - (HF) n ( n =1-3), the energies for the loss of HF from F - (HF) 3 , F - (HF) 2 , and F - (HF) were evaluated to be 1 eV or lower, 1 eV or higher, and 2 eV, respectively, on the basis of their center-of-mass energy ( E CM ). These E CM values were consistent with the values of 0.995, 1.308, and 2.048 eV, respectively, obtained by ab initio calculations. The stability of [O 2 (HF) n ] - ( n =1-4) was discussed on the basis of the bond lengths of O 2 H-F - (HF) n and O 2 - H-F(HF) n obtained by ab initio calculations. The calculations indicated that [O 2 (HF) 4 ] - separated into O 2 H and F - (HF) 3 .

  9. TID measurement using oblique transmissions of HF pulses

    Science.gov (United States)

    Galkin, Ivan; Reinisch, Bodo; Huang, Xueqin; Paznukhov, Vadym; Hamel, Ryan; Kozlov, Alexander; Belehaki, Anna

    2017-04-01

    The Traveling Ionospheric Disturbance (TID), a wave-like signature of moving plasma density modulation in the ionosphere, is widely acknowledged for its utility in backtracking the anomalous events responsible for the TID generation, and as a major inconvenience to high-frequency (HF) operational systems because of its deleterious impact on the accuracy of navigation and geolocation. The pilot project "Net-TIDE" for the real-time detection and evaluation of TIDs began its operation in 2016 based on the remote-sensing data from synchronized, network-coordinated HF sounding between pairs of DPS4D ionosondes at five participating observatories in Europe. Measurement of all signal properties (Doppler frequency, angle of arrival, and time-of-flight from transmitter to receiver) proved to be instrumental in detecting the TID and deducing the TID parameters: amplitude, wavelength, phase velocity, and direction of propagation. Processing of the measured HF signal data required a specialized signal processing technique that is capable of consistently extracting different signals that have propagated along different ionospheric paths. The multi-path signal environment proved to be the greatest challenge for the reliable TID specification by Net-TIDE, demanding the development of an intelligent system for "signal tracking". The intelligent system is based on a neural network model of a pre-attentive vision capable of extracting continuous signal tracks from the multi-path signal ensemble. Specific examples of the Net-TIDE algorithm suite operation and its suitability for a fully automated TID warning service are discussed.

  10. Modeling of NiTiHf using finite difference method

    Science.gov (United States)

    Farjam, Nazanin; Mehrabi, Reza; Karaca, Haluk; Mirzaeifar, Reza; Elahinia, Mohammad

    2018-03-01

    NiTiHf is a high temperature and high strength shape memory alloy with transformation temperatures above 100oC. A constitutive model based on Gibbs free energy is developed to predict the behavior of this material. Two different irrecoverable strains including transformation induced plastic strain (TRIP) and viscoplastic strain (VP) are considered when using high temperature shape memory alloys (HTSMAs). The first one happens during transformation at high levels of stress and the second one is related to the creep which is rate-dependent. The developed model is implemented for NiTiHf under uniaxial loading. Finite difference method is utilized to solve the proposed equations. The material parameters in the equations are calibrated from experimental data. Simulation results are captured to investigate the superelastic behavior of NiTiHf. The extracted results are compared with experimental tests of isobaric heating and cooling at different levels of stress and also superelastic tests at different levels of temperature. More results are generated to investigate the capability of the proposed model in the prediction of the irrecoverable strain after full transformation in HTSMAs.

  11. 40 CFR Table 3 to Subpart Ggg of... - Soluble HAP

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 11 2010-07-01 2010-07-01 true Soluble HAP 3 Table 3 to Subpart GGG of Part 63 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED... HAP Compound 1,1-Dimethylhydrazine. 1,4-Dioxane. Acetonitrile. Acetophenone. Diethyl sulfate. Dimethyl...

  12. Investigation of new type Cu-Hf-Al bulk glassy alloys

    International Nuclear Information System (INIS)

    Nagy, E; Ronto, V; Solyom, J; Roosz, A

    2009-01-01

    In the last years new type Cu-Hf-Al ternary alloys were developed with high glass forming ability and ductility. The addition of Al to Cu-Hf alloys results in improvements in glass formation, thermal stability and mechanical properties of these alloys. We have investigated new Cu-based bulk amorphous alloys in Cu-Hf-Al ternary system. The alloys with Cu 49 Hf 42 Al 9 , Cu 46 Hf 45 Al 9 , Cu 50 Hf 42.5 Al 7.5 and Cu 50 Hf 45 Al 5 compositions were prepared by arc melting. The samples were made by centrifugal casting and were investigated by X-ray diffraction method. Thermodynamic properties were examined by differential scanning calorimetry and the structure of the crystallising phases by scanning electron microscopy. The determination of liquidus temperatures of alloys were measured by differential thermal analysis.

  13. Solubility limits on radionuclide dissolution

    Energy Technology Data Exchange (ETDEWEB)

    Kerrisk, J.F.

    1984-12-31

    This paper examines the effects of solubility in limiting dissolution rates of a number of important radionuclides from spent fuel and high-level waste. Two simple dissolution models were used for calculations that would be characteristics of a Yucca Mountain repository. A saturation-limited dissolution model, in which the water flowing through the repository is assumed to be saturated with each waste element, is very conservative in that it overestimates dissolution rates. A diffusion-limited dissolution model, in which element-dissolution rates are limited by diffusion of waste elements into water flowing past the waste, is more realistic, but it is subject to some uncertainty at this time. Dissolution rates of some elements (Pu, Am, Sn, Th, Zr, Sm) are always limited by solubility. Dissolution rates of other elements (Cs, Tc, Np, Sr, C, I) are never solubility limited; their release would be limited by dissolution of the bulk waste form. Still other elements (U, Cm, Ni, Ra) show solubility-limited dissolution under some conditions. 9 references, 3 tables.

  14. Solubility of Nd in brine

    International Nuclear Information System (INIS)

    Khalili, F.I.; Symeopoulos, V.; Chen, J.F.; Choppin, G.R.

    1994-01-01

    The solubility of Nd(III) has been measured at 23±3 C in a synthetic brine at pcH 6.4, 8.4, 10.4 and 12.4. The brine consisted predominantly of (Na+K)Cl and MgCl 2 with an ionic strength of 7.8 M (9.4 m) a solid compound of Nd(III) at each pcH was assigned from X-ray diffraction patterns. The log values of the experimental solubilities decrease fomr -3 at pcH 6.4 to -5.8 at pcH 8.4; at pcH 10.4 and 12.4 the solubility was below the detection limit of -7.5. The experimental solubility does not follow closely the variation with pcH estimated from modeling of the species in solution in equilibrium with the Nd solid using S.I.T. (orig.)

  15. Nightside studies of coherent HF Radar spectral width behaviour

    Directory of Open Access Journals (Sweden)

    E. E. Woodfield

    2002-09-01

    Full Text Available A previous case study found a relationship between high spectral width measured by the CUTLASS Finland HF radar and elevated electron temperatures observed by the EISCAT and ESR incoherent scatter radars in the post-midnight sector of magnetic local time. This paper expands that work by briefly re-examining that interval and looking in depth at two further case studies. In all three cases a region of high HF spectral width (>200 ms-1 exists poleward of a region of low HF spectral width (<200 ms-1. Each case, however, occurs under quite different geomagnetic conditions. The original case study occurred during an interval with no observed electrojet activity, the second study during a transition from quiet to active conditions with a clear band of ion frictional heating indicating the location of the flow reversal boundary, and the third during an isolated sub-storm. These case studies indicate that the relationship between elevated electron temperature and high HF radar spectral width appears on closed field lines after 03:00 magnetic local time (MLT on the nightside. It is not clear whether the same relationship would hold on open field lines, since our analysis of this relationship is restricted in latitude. We find two important properties of high spectral width data on the nightside. Firstly the high spectral width values occur on both open and closed field lines, and secondly that the power spectra which exhibit high widths are both single-peak and multiple-peak. In general the regions of high spectral width (>200 ms-1 have more multiple-peak spectra than the regions of low spectral widths whilst still maintaining a majority of single-peak spectra. We also find that the region of ion frictional heating is collocated with many multiple-peak HF spectra. Several mechanisms for the generation of high spectral width have been proposed which would produce multiple-peak spectra, these are discussed in relation to the data presented here. Since the

  16. Nightside studies of coherent HF Radar spectral width behaviour

    Directory of Open Access Journals (Sweden)

    E. E. Woodfield

    Full Text Available A previous case study found a relationship between high spectral width measured by the CUTLASS Finland HF radar and elevated electron temperatures observed by the EISCAT and ESR incoherent scatter radars in the post-midnight sector of magnetic local time. This paper expands that work by briefly re-examining that interval and looking in depth at two further case studies. In all three cases a region of high HF spectral width (>200 ms-1 exists poleward of a region of low HF spectral width (<200 ms-1. Each case, however, occurs under quite different geomagnetic conditions. The original case study occurred during an interval with no observed electrojet activity, the second study during a transition from quiet to active conditions with a clear band of ion frictional heating indicating the location of the flow reversal boundary, and the third during an isolated sub-storm. These case studies indicate that the relationship between elevated electron temperature and high HF radar spectral width appears on closed field lines after 03:00 magnetic local time (MLT on the nightside. It is not clear whether the same relationship would hold on open field lines, since our analysis of this relationship is restricted in latitude. We find two important properties of high spectral width data on the nightside. Firstly the high spectral width values occur on both open and closed field lines, and secondly that the power spectra which exhibit high widths are both single-peak and multiple-peak. In general the regions of high spectral width (>200 ms-1 have more multiple-peak spectra than the regions of low spectral widths whilst still maintaining a majority of single-peak spectra. We also find that the region of ion frictional heating is collocated with many multiple-peak HF spectra. Several mechanisms for the generation of high spectral width have been proposed which would produce multiple-peak spectra, these are discussed in relation to

  17. Impact of polymer type on bioperformance and physical stability of hot melt extruded formulations of a poorly water soluble drug.

    Science.gov (United States)

    Mitra, Amitava; Li, Li; Marsac, Patrick; Marks, Brian; Liu, Zhen; Brown, Chad

    2016-05-30

    Amorphous solid dispersion formulations have been widely used to enhance bioavailability of poorly soluble drugs. In these formulations, polymer is included to physically stabilize the amorphous drug by dispersing it in the polymeric carrier and thus forming a solid solution. The polymer can also maintain supersaturation and promote speciation during dissolution, thus enabling better absorption as compared to crystalline drug substance. In this paper, we report the use of hot melt extrusion (HME) to develop amorphous formulations of a poorly soluble compound (FaSSIF solubility=1μg/mL). The poor solubility of the compound and high dose (300mg) necessitated the use of amorphous formulation to achieve adequate bioperformance. The effect of using three different polymers (HPMCAS-HF, HPMCAS-LF and copovidone), on the dissolution, physical stability, and bioperformance of the formulations was demonstrated. In this particular case, HPMCAS-HF containing HME provided the highest bioavailability and also had better physical stability as compared to extrudates using HPMCAS-LF and copovidone. The data demonstrated that the polymer type can have significant impact on the formulation bioperformance and physical stability. Thus a thorough understanding of the polymer choice is imperative when designing an amorphous solid dispersion formulation, such that the formulation provides robust bioperformance and has adequate shelf life. Copyright © 2016 Elsevier B.V. All rights reserved.

  18. Terminal solid solubility of hydrogen in titanium

    International Nuclear Information System (INIS)

    Giroldi, J.P.; Vizcaino, Pablo; Banchik, Abraham David

    2003-01-01

    A Research and Development program to build a data base is currently under progress to support the local titanium fabrication. In the present work the temperature of the Terminal Solid Solubility on dissolution (TSSd) and precipitation (TSSp) of titanium hydrides in the Ti α-phase were both measured in the same thermal cycle with a Differential Scanning Calorimeter (DSC). The local titanium producer (FAESA) provided ASTM grade 1 pure Ti bars of about 2,5 cm in diameter. Samples weighting between 50 to 200 mg were cut with a diamond disc and the parallelepiped faces were all carefully ground with SiC papers, then picked in a HNO 3 plus HF aqueous solution and finally dried out with ethanol and hot air. Pairs of (TSSd, TSSp) values for α + δ → α and α → α + δ transformation temperatures in titanium were determined with the same calorimetric procedure already used to calculate the TSS values in zirconium. Data were taken from the same sample during the heating up and cooling down cycle of the second calorimeter run made with the same rate of 20 C degrees / minute. The Cathodic Charging technique was used to charge the samples at different hydrogen concentrations between the 'as fabricated' value and the concentration corresponding to the eutectoid temperature. A mixture of glycerin and phosphoric acid in a 2:1 ratio and a current density of 0,05 to 0,1 Amp/cm 2 were applied to different samples during 24 to 96 hours to get a wide range of hydrogen concentrations. A homogenization heat treatment at 400 C degrees for 45 minutes -made at open air in an electric furnace- was applied to each sample to dissolve the massive hydrides at the sample surfaces and diffuse them into the bulk of the sample. The hydrogen concentration of each sample was measured after the final calorimetric run using the Extraction Method in Liquid State under an inert atmosphere using a Leco RH-404 model Hydrogen Determinator. The experimental data follows a linear relationship -with a

  19. Anion exchange behavior of Ti, Zr, Hf, Nb and Ta as homologues of Rf and Db in mixed HF-acetone solutions

    International Nuclear Information System (INIS)

    Aksenov, N.V.; Bozhikov, G.A.; Starodub, G.Ya.; Dmitriev, S.N.; Filosofov, D.V.; Jon Sun Jin; Radchenko, V.I.; Lebedev, N.A.; Novgorodov, A.F.

    2009-01-01

    We studied in detail the sorption behavior of Ti, Zr, Hf, Nb and Ta on AG 1 anion exchange resin in HF-acetone mixed solutions as a function of organic cosolvent and acid concentrations. Anion exchange behavior was found to be strongly acetone concentration dependent. The distribution coefficients of Ti, Zr, Hf and Nb increased and those of Ta decreased with increasing content of acetone in HF solutions. With increasing HF concentration, anion exchange equilibrium analysis indicated the formation of fluoride complexes of group-4 elements with charge -3 and Ta with charge -2. For Nb the slope of -2 increased up to -5. Optimal conditions for separation of the elements using AIX chromatography were found. Group-4 elements formed MF 7 3- (M = Ti, Zr, Hf) complexes whose sorption decreased Ti > Hf > Zr in reverse order of complex stability. This fact is of particular interest for studying ion exchange behavior of Rf compared to Ti. The advantages of studying chemical properties of Rf and Db in aqueous HF solutions mixed with organic solvents are briefly discussed

  20. A Soluble, Folded Protein without Charged Amino Acid Residues

    DEFF Research Database (Denmark)

    Højgaard, Casper; Kofoed, Christian; Espersen, Roall

    2016-01-01

    Charges are considered an integral part of protein structure and function, enhancing solubility and providing specificity in molecular interactions. We wished to investigate whether charged amino acids are indeed required for protein biogenesis and whether a protein completely free of titratable...... side chains can maintain solubility, stability, and function. As a model, we used a cellulose-binding domain from Cellulomonas fimi, which, among proteins of more than 100 amino acids, presently is the least charged in the Protein Data Bank, with a total of only four titratable residues. We find...

  1. Solubility of sparingly soluble drug derivatives of anthranilic acid.

    Science.gov (United States)

    Domańska, Urszula; Pobudkowska, Aneta; Pelczarska, Aleksandra

    2011-03-24

    This work is a continuation of our systematic study of the solubility of pharmaceuticals (Pharms). All substances here are derivatives of anthranilic acid, and have an anti-inflammatory direction of action (niflumic acid, flufenamic acid, and diclofenac sodium). The basic thermal properties of pure Pharms, i.e., melting and glass-transition temperatures as well as the enthalpy of melting, have been measured with the differential scanning microcalorimetry technique (DSC). Molar volumes have been calculated with the Barton group contribution method. The equilibrium mole fraction solubilities of three pharmaceuticals were measured in a range of temperatures from 285 to 355 K in three important solvents for Pharm investigations: water, ethanol, and 1-octanol using a dynamic method and spectroscopic UV-vis method. The experimental solubility data have been correlated by means of the commonly known G(E) equation: the NRTL, with the assumption that the systems studied here have revealed simple eutectic mixtures. pK(a) precise measurement values have been investigated with the Bates-Schwarzenbach spectrophotometric method. © 2011 American Chemical Society

  2. Evolution of the mantle source in an evolving arc-backarc system (Torres del Paine, Patagonia): Evidence from Hf isotopes in zircon

    Science.gov (United States)

    Ewing, T. A.; Muntener, O.; Leuthold, J.; Baumgartner, L. P.; Putlitz, B.; d'Abzac, F. X.; Chiaradia, M.

    2015-12-01

    The Miocene Torres del Paine intrusive complex (TPIC) in Patagonia is a transitional alkaline backarc intrusion1 emplaced on short timescales of 162 ± 11 ka2. It is subdivided into two units with distinct ages of ~12.6 Ma and ~12.45 Ma1. Smaller intrusive bodies in the area record a change in chemistry from calc-alkaline at ~16 Ma, to transitional alkaline at ~12.5 Ma. Zircons from ~16 Ma intrusives and the 12.6 Ma part of the TPIC have remarkably consistent, slightly enriched Hf isotope compositions with ɛHf(i) of -1 to +2. An abrupt shift towards more juvenile Hf isotope compositions is observed in the ~12.45 Ma part of the TPIC, with ɛHf(i) of +3 to +6. Bulk rock Nd and Sr isotopes for the TPIC show the same shift towards more juvenile compositions at this time1. The long-term consistency of ɛHf(i) from 16 to 12.6 Ma is surprising, given that in the same period the bulk rock chemistry changes from calc-alkaline to transitional alkaline. Conversely, the major shift in ɛHf(i) is not correlated with any change in bulk rock chemistry, which remains transitional alkaline from 12.6 to 12.45 Ma. The decoupling of major element chemical evolution and Hf isotope signatures suggests that the subsequent rapid influx of juvenile material recorded by our Hf isotope data must have occurred by renewed mantle melting. Subduction of the Chile ridge at ~12.5 Ma in this area caused arc magmatism to move westwards and back-arc extension to initiate. We propose that the first TPIC magmas (12.6 Ma) came from a mantle wedge with a residual subduction signature. Subsequent melting of more juvenile mantle, less contaminated by a subduction component, generated the 12.45 Ma TPIC magmas. These results demonstrate that magmatic complexes such as the TPIC may tap distinct mantle sources even on very short timescales, fingerprinting arc-backarc transition processes. 1Leuthold et al., 2013, JPET, 54: 273-303 2Leuthold et al., 2012, EPSL, 325: 85-92

  3. Temperature dependence of the resistivity and tunneling magnetoresistance of sputtered FeHf(Si)O cermet films

    NARCIS (Netherlands)

    Strijkers, G.J.; Swagten, H.J.M.; Rulkens, B.; Bitter, R.H.J.N.; Jonge, de W.J.M.; Bloemen, P.J.H.; Schep, K.M.

    1998-01-01

    We have studied the tunneling resistivity and magnetoresistance of reactive sputter deposited FeHfO and FeHfSiO thin granular films. Maximum magnetoresistance ratios at room temperature of 2% and 3.2% were observed for films with compositions of Fe47Hf10O43 and Fe40Hf6Si6O48, respectively. The

  4. Investigational research on highly functional carbon and related materials (HF-CRMs); Tansokei kokino zairyo no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper arranged a fiscal 1997 guiding study of highly functional carbon and related materials (HF-CRMs). In the material invention field, described were the composition by interatomic control technology and the characteristics of pure carbon nanotubes, carbynes, graphite, fullerene polymer, porous carbon, etc. Heteroelement substituted materials were also described. The paper also reported the application of HF-CRMs to the electric/chemical field, and arranged the basement technology and applicability of diamond in particular. The subjects are enhancement of composition technology and reduction of the price of processing technology. Especially, the control of impurities and defects is a must for the electric use. The application of HF-CRMs to the mechanical field was reported. Superlubricant, wear resistant and high temperature corrosion resistant materials were taken up, and were surveyed in terms of their use mostly to refuse incineration power generation boilers, and thermal power generation use turbines. In the development of mechanical materials, technologies were surveyed especially for large area/complex shape film formation to form films for various parts, functionally gradient film formation for relaxation of thermal stress and residual stress in the film, and high speed film formation for quantity production. 363 refs., 88 figs., 10 tabs.

  5. Thermodynamics of HfCl/sub 4/-KCl molten mixtures containing HfCl/sub 4/ up to 33. 3 mol. per cent

    Energy Technology Data Exchange (ETDEWEB)

    Smirnov, M V; Salyulev, A B; Kudyakov, V Ya [AN SSSR, Sverdlovsk. Inst. Ehlektrokhimii

    1980-05-01

    Based on measurements of saturated vapour pressure in components of melted mixtures of HfCl/sub 4/-KCl, depending on temperature and concentration, calculated are the results of changes in activity coefficients of hafnium tetrachloride and potassium chloride on transition from diluted solutions, where the Henry law is met, to those concentrated where the law is disobeyed. Growth in the activity coefficient of HfCl/sub 4/ is due to dissociation of complex groups of HfCl/sub 6//sup 2 -/ into complexes with a lesser number of ligands and decreasing relative binding energy of Hf/sup 4 +/-Cl/sup -/ there. In this case, marked changes take place in partial enthalpy and entropy of hafnium tetrachloride mixing. Similar dependences are observed for potassium chloride, but they are expressed considerably weaker. Evaporation enthalpy and entropy are calculated for HfCl/sub 4/ and KCl monomers from their melted mixtures of various concentrations.

  6. Thermodynamics of HfCl4-KCl molten mixtures containing HfCl4 up to 33.3 mol. per cent

    International Nuclear Information System (INIS)

    Smirnov, M.V.; Salyulev, A.B.; Kudyakov, V.Ya.

    1980-01-01

    Based on measurements of saturated vapour pressure in components of melted mixtures of HfCl 4 -KCl, depending on temperature and concentration, calculated are the results of changes in activity coefficients of hafnium tetrachloride and potassium chloride on transition from diluted solutions, where the Henry law is met, to those concentrated where the law is disobeyed. Growth in the activity coefficient of HfCl 4 is due to dissociation of complex groups of HfCl 6 2- into complexes with a lesser number of ligands and decreasing relative binding energy of Hf 4+ -Cl - there. In this case, marked changes take place in partial enthalpy and entropy of hafnium tetrachloride mixing. Similar dependences are observed for potassium chloride, but they are expressed considerably weaker. Evaporation enthalpy and entropy are calculated for HfCl 4 and KCl monomers from their melted mixtures of various concentrations

  7. Comparative Analysis of the $^{178m2}$Hf Yield at Reactions with Different Projectiles

    CERN Document Server

    Karamian, S A

    2004-01-01

    The long-lived high-spin $^{178m2}$Hf $K$-isomer can be produced in nuclear reactions with different projectiles. The reaction yields and cross-sections have been measured in the series of experiments and the results are now overviewed. The systematics of isomer-to-ground state ratios are drawn and real production capabilities are estimated for the best reactions. Such a summary is relevant to the significance of the isomer studies both for the nuclear-science knowledge and for possible applications. Potential isomer applications have been earlier stressed in popular publications with probably overestimated expectations. The real possibilities are restricted in part by the production yield and by other shortcomings as well.

  8. Solidification Rate Dependence of Microstructures and Transformation Behavior of Ti-Ni-Hf Alloys.

    Science.gov (United States)

    Kim, Dong-Jo; Kim, Yeon-Wook; Nam, Tae-Hyun

    2018-09-01

    The microstructures and transformation behavior of Ti-49Ni-20Hf, Ti-49.5Ni-20Hf and Ti-50.3Ni- 20Hf alloys, when prepared by conventional casting, were investigated and compared with the properties of the alloys prepared by melt spinning. The area fraction of (Ti,Hf)2Ni in Ti-Ni-Hf alloys decreased to 3.9% from 9.4% as Ni content rose to 50.3 at% from 49 at%. Several cracks were observed in the hot-rolled Ti-49Ni-20Hf alloy sheet but none were found in the Ti-50.3Ni-20Hf alloy sheet. The B2-B19' transformation start temperature (Ms) decreased to 476 K from 580 K as Ni content increased to 50.3 at% from 49 at%. All the as-spun ribbons were amorphous, and the activation energy for crystallization ranged from 167.8 kJ/mol to 182.7 kJ/mol based on Ni content. When annealing temperature ranged from 810 K to 873 K, crystalline Ti-Ni-Hf alloys without (Ti,Hf)2Ni particles were obtained. At annealing temperatures higher than 873 K, very fine (Ti,Hf)2Ni particles, less than 20 nm in size, were found embedded in a crystalline matrix.

  9. Effects of HfB2 and HfN Additions on the Microstructures and Mechanical Properties of TiB2-Based Ceramic Tool Materials

    Science.gov (United States)

    An, Jing; Song, Jinpeng; Liang, Guoxing; Gao, Jiaojiao; Xie, Juncai; Cao, Lei; Wang, Shiying; Lv, Ming

    2017-01-01

    The effects of HfB2 and HfN additions on the microstructures and mechanical properties of TiB2-based ceramic tool materials were investigated. The results showed that the HfB2 additive not only can inhibit the TiB2 grain growth but can also change the morphology of some TiB2 grains from bigger polygons to smaller polygons or longer ovals that are advantageous for forming a relatively fine microstructure, and that the HfN additive had a tendency toward agglomeration. The improvement of flexural strength and Vickers hardness of the TiB2-HfB2 ceramics was due to the relatively fine microstructure; the decrease of fracture toughness was ascribed to the formation of a weaker grain boundary strength due to the brittle rim phase and the poor wettability between HfB2 and Ni. The decrease of the flexural strength and Vickers hardness of the TiB2-HfN ceramics was due to the increase of defects such as TiB2 coarse grains and HfN agglomeration; the enhancement of fracture toughness was mainly attributed to the decrease of the pore number and the increase of the rim phase and TiB2 coarse grains. The toughening mechanisms of TiB2-HfB2 ceramics mainly included crack bridging and transgranular fracture, while the toughening mechanisms of TiB2-HfN ceramics mainly included crack deflection, crack bridging, transgranular fracture, and the core-rim structure. PMID:28772821

  10. Effects of HfB2 and HfN Additions on the Microstructures and Mechanical Properties of TiB2-Based Ceramic Tool Materials

    Directory of Open Access Journals (Sweden)

    Jing An

    2017-04-01

    Full Text Available The effects of HfB2 and HfN additions on the microstructures and mechanical properties of TiB2-based ceramic tool materials were investigated. The results showed that the HfB2 additive not only can inhibit the TiB2 grain growth but can also change the morphology of some TiB2 grains from bigger polygons to smaller polygons or longer ovals that are advantageous for forming a relatively fine microstructure, and that the HfN additive had a tendency toward agglomeration. The improvement of flexural strength and Vickers hardness of the TiB2-HfB2 ceramics was due to the relatively fine microstructure; the decrease of fracture toughness was ascribed to the formation of a weaker grain boundary strength due to the brittle rim phase and the poor wettability between HfB2 and Ni. The decrease of the flexural strength and Vickers hardness of the TiB2-HfN ceramics was due to the increase of defects such as TiB2 coarse grains and HfN agglomeration; the enhancement of fracture toughness was mainly attributed to the decrease of the pore number and the increase of the rim phase and TiB2 coarse grains. The toughening mechanisms of TiB2-HfB2 ceramics mainly included crack bridging and transgranular fracture, while the toughening mechanisms of TiB2-HfN ceramics mainly included crack deflection, crack bridging, transgranular fracture, and the core-rim structure.

  11. HF diets increase hypothalamic PTP1B and induce leptin resistance through both leptin-dependent and -independent mechanisms

    Science.gov (United States)

    White, Christy L.; Whittington, Amy; Barnes, Maria J.; Wang, Zhong; Bray, George A.; Morrison, Christopher D.

    2009-01-01

    Protein tyrosine phosphatase 1B (PTP1B) contributes to leptin resistance by inhibiting intracellular leptin receptor signaling. Mice with whole body or neuron-specific deletion of PTP1B are hypersensitive to leptin and resistant to diet-induced obesity. Here we report a significant increase in PTP1B protein levels in the mediobasal hypothalamus (P = 0.003) and a concomitant reduction in leptin sensitivity following 28 days of high-fat (HF) feeding in rats. A significant increase in PTP1B mRNA levels was also observed in rats chronically infused with leptin (3 μg/day icv) for 14 days (P = 0.01) and in leptin-deficient ob/ob mice infused with leptin (5 μg/day sc for 14 days; P = 0.003). When saline-infused ob/ob mice were placed on a HF diet for 14 days, an increase in hypothalamic PTP1B mRNA expression was detected (P = 0.001) despite the absence of circulating leptin. In addition, although ob/ob mice were much more sensitive to leptin on a low-fat (LF) diet, a reduction in this sensitivity was still observed following exposure to a HF diet. Taken together, these data indicate that hypothalamic PTP1B is specifically increased during HF diet-induced leptin resistance. This increase in PTP1B is due in part to chronic hyperleptinemia, suggesting that hyperleptinemia is one mechanism contributing to the development of leptin resistance. However, these data also indicate that leptin is not required for the increase in hypothalamic PTP1B or the development of leptin resistance. Therefore, additional, leptin-independent mechanisms must exist that increase hypothalamic PTP1B and contribute to leptin resistance. PMID:19017730

  12. Near-field solubility studies

    International Nuclear Information System (INIS)

    Thomason, H.P.; Williams, S.J.

    1992-02-01

    Experimental determinations of the solubilities of americium, plutonium, neptunium, protactinium, thorium, radium, lead, tin, palladium and zirconium are reported. These elements have radioactive isotopes of concern in assessments of radioactive waste disposal. All measurements were made under the highly alkaline conditions typical of the near field of a radioactive waste repository which uses cementitious materials for many of the immobilisation matrices, the backfill and the engineered structures. Low redox potentials, typical of those resulting from the corrosion of iron and steel, were simulated for those elements having more than one accessible oxidation state. The dissolved concentrations of the elements were defined using ultrafiltration. In addition, the corrosion of iron and stainless steel was shown to generate low redox potentials in solution and the solubility of iron(II) at high pH was measured and found to be sufficient for it to act as a redox buffer with respect to neptunium and plutonium. (author)

  13. Low lying magnetic dipole strength distribution in 176Hf

    International Nuclear Information System (INIS)

    Kuliev, A. A.; Ertugral, F.; Yakut, H.; Bektasoglu, M.; Guliyev, E.

    2006-01-01

    In this study the scissors mode 1 + states are systematically investigated within the rotational invariant Quasiparticle Random Phase Approximation (QRPA) for 1 76Hf isotopes. We consider the 1 + vibrations generated by the isovector spin-spin interactions and the isoscalar (h 0 ) and isovector (h 1 ) quadrupole type separable forces restoring the broken symmetry by a deformed mean field. It has been shown that restoration of the broken rotational symmetry of the Hamiltonian essentially decreases the B(M1) value of the low lying 1 + states and increases the collectivization of the scissors mode excitations in the spectroscopic energy region. Agreement between the calculated mean excitation energies as well as the summed B(M1) value of the scissors mode excitations and the available experimental data of 1 76Hf is rather good. For instance, distributions of the calculated B(M1) transition strengths in the 1 76 Hf isotopes with respect to K π =1 + excitations is represented in Figure. Thus, we see that the models which use the Hamiltonian with broken rotational symmetry strongly overestimate the M1 strength at low energy. These results indicate an importance of the models which are free from the low-energy spurious states. The marked differences between the results for 1 + states, calculated in rotational invariant (RI) and non-rotational invariant (NRI) model indicate the importance of the approaches which are free from spurious low-energy solutions. A separation of the rotational state from the 1 + states changes somewhat the distribution of the B(M1) strength in the spectroscopic energy region and increases the fragmentation of the scissors mode 1 + excitations in agreement with the experimental data

  14. High Q-factor tunable superconducting HF circuit

    CERN Document Server

    Vopilkin, E A; Pavlov, S A; Ponomarev, L I; Ganitsev, A Y; Zhukov, A S; Vladimirov, V V; Letyago, A G; Parshikov, V V

    2001-01-01

    Feasibility of constructing a high Q-factor (Q approx 10 sup 5) mechanically tunable in a wide range of frequencies (12-63 MHz) vibration circuit of HF range was considered. The tunable circuit integrates two single circuits made using YBaCuO films. The circuit frequency is tuned by changing distance X (capacity) between substrates. Potentiality of using substrates of lanthanum aluminate, neodymium gallate and strontium titanate for manufacture of single circuits was considered. Q-factor of the circuit amounted to 68000 at resonance frequency of 6.88 MHz

  15. High Q-factor tunable superconducting HF circuit

    International Nuclear Information System (INIS)

    Vopilkin, E.A.; Parafin, A.E.; Pavlov, S.A.; Ponomarev, L.I.; Ganitsev, A.Yu.; Zhukov, A.S.; Vladimirov, V.V.; Letyago, A.G.; Parshikov, V.V.

    2001-01-01

    Feasibility of constructing a high Q-factor (Q ∼ 10 5 ) mechanically tunable in a wide range of frequencies (12-63 MHz) vibration circuit of HF range was considered. The tunable circuit integrates two single circuits made using YBaCuO films. The circuit frequency is tuned by changing distance X (capacity) between substrates. Potentiality of using substrates of lanthanum aluminate, neodymium gallate and strontium titanate for manufacture of single circuits was considered. Q-factor of the circuit amounted to 68000 at resonance frequency of 6.88 MHz [ru

  16. TEA HF laser with a high specific radiation energy

    Science.gov (United States)

    Puchikin, A. V.; Andreev, M. V.; Losev, V. F.; Panchenko, Yu. N.

    2017-01-01

    Results of experimental studies of the chemical HF laser with a non-chain reaction are presented. The possibility of the total laser efficiency of 5 % is shown when a traditional C-to-C pumping circuit with the charging voltage of 20-24 kV is used. It is experimentally shown that the specific radiation output energy of 21 J/l is reached at the specific pump energy of 350 J/l in SF6/H2 = 14/1 mixture at the total pressure of 0.27 bar.

  17. Ionosphere research with a HF/MF cubesat radio instrument

    Science.gov (United States)

    Kallio, Esa; Aikio, Anita; Alho, Markku; Fontell, Mathias; Harri, Ari-Matti; Kauristie, Kirsti; Kestilä, Antti; Koskimaa, Petri; Mäkelä, Jakke; Mäkelä, Miika; Turunen, Esa; Vanhamäki, Heikki; Verronen, Pekka

    2017-04-01

    New technology provides new possibilities to study geospace and 3D ionosphere by using spacecraft and computer simulations. A type of nanosatellites, CubeSats, provide a cost effective possibility to provide in-situ measurements in the ionosphere. Moreover, combined CubeSat observations with ground-based observations gives a new view on auroras and associated electromagnetic phenomena. Especially joint and active CubeSat - ground based observation campaigns enable the possibility of studying the 3D structure of the ionosphere. Furthermore using several CubeSats to form satellite constellations enables much higher temporal resolution. At the same time, increasing computation capacity has made it possible to perform simulations where properties of the ionosphere, such as propagation of the electromagnetic waves in the medium frequency, MF (0.3-3 MHz) and high frequency, HF (3-30 MHz), ranges is based on a 3D ionospheric model and on first-principles modelling. Electromagnetic waves at those frequencies are strongly affected by ionospheric electrons and, consequently, those frequencies can be used for studying the plasma. On the other hand, even if the ionosphere originally enables long-range telecommunication at MF and HF frequencies, the frequent occurrence of spatiotemporal variations in the ionosphere disturbs communication channels, especially at high latitudes. Therefore, study of the MF and HF waves in the ionosphere has both a strong science and technology interests. We introduce recently developed simulation models as well as measuring principles and techniques to investigate the arctic ionosphere by a polar orbiting CubeSat whose novel AM radio instrument measures HF and MF waves. The cubesat, which contains also a white light aurora camera, is planned to be launched in late 2017 (http://www.suomi100satelliitti.fi/eng). The new models are (1) a 3D ray tracing model and (2) a 3D full kinetic electromagnetic simulation. We also introduce how combining of the

  18. Azeotrope in LiF-HfF4 system

    International Nuclear Information System (INIS)

    Sorokin, I.D.; Korenev, Yu.M.; Sidorov, L.N.

    1975-01-01

    The gaseous phase of the system LiF-HfF 4 is investigated by means of isothermal evaporation. Using experimental data, p-X diagrams are constructed for 1125, 1075, 1025, 975 and 925 K. It is shown that the azeotrope with minimum total pressure observed at 1125 K degenerates upon lowering of the temperature and entry into the heterogeneous region. At 975 K the azeotrope corresponds to the point of inflexion from the horizontal tangent on the total pressure curve. At lower temperatures azeotropic distillation is absent from the system. (author)

  19. The Solubility Parameters of Ionic Liquids

    Science.gov (United States)

    Marciniak, Andrzej

    2010-01-01

    The Hildebrand’s solubility parameters have been calculated for 18 ionic liquids from the inverse gas chromatography measurements of the activity coefficients at infinite dilution. Retention data were used for the calculation. The solubility parameters are helpful for the prediction of the solubility in the binary solvent mixtures. From the solubility parameters, the standard enthalpies of vaporization of ionic liquids were estimated. PMID:20559495

  20. The Solubility Parameters of Ionic Liquids

    Directory of Open Access Journals (Sweden)

    Andrzej Marciniak

    2010-04-01

    Full Text Available The Hildebrand’s solubility parameters have been calculated for 18 ionic liquids from the inverse gas chromatography measurements of the activity coefficients at infinite dilution. Retention data were used for the calculation. The solubility parameters are helpful for the prediction of the solubility in the binary solvent mixtures. From the solubility parameters, the standard enthalpies of vaporization of ionic liquids were estimated.

  1. Solubility of Carbon in Nanocrystalline -Iron

    OpenAIRE

    Alexander Kirchner; Bernd Kieback

    2012-01-01

    A thermodynamic model for nanocrystalline interstitial alloys is presented. The equilibrium solid solubility of carbon in -iron is calculated for given grain size. Inside the strained nanograins local variation of the carbon content is predicted. Due to the nonlinear relation between strain and solubility, the averaged solubility in the grain interior increases with decreasing grain size. The majority of the global solubility enhancement is due to grain boundary enrichment however. Therefor...

  2. Soluble pig for radioactive waste transfer lines

    International Nuclear Information System (INIS)

    Ohl, P.C.; Pezeshki, C.

    1997-01-01

    Flushing transfer pipe after radioactive waste transfers generates thousands of gallons of additional radioactive waste each year at the Hanford site. The use of pneumatic pigging with waste soluble pigs as a means to clear transfer piping may be an effective alternative to raw water flushes. A feasibility study was performed by a group of senior mechanical engineering students for their senior design project as part of their curriculum at Washington State University. The students divided the feasibility study into three sub-projects involving: (1) material research, (2) delivery system design, and (3) mockup fabrication and testing. The students screened through twenty-three candidate materials and selected a thermoplastic polymer combined 50:50 wt% with sucrose to meet the established material performance criteria. The students also prepared a conceptual design of a remote pneumatic delivery system and constructed a mockup section of transfer pipe for testing the prototype pigs

  3. A routine high-precision method for Lu-Hf isotope geochemistry and chronology

    Science.gov (United States)

    Patchett, P.J.; Tatsumoto, M.

    1981-01-01

    A method for chemical separation of Lu and Hf from rock, meteorite and mineral samples is described, together with a much improved mass spectrometric running technique for Hf. This allows (i) geo- and cosmochronology using the176Lu???176Hf+??- decay scheme, and (ii) geochemical studies of planetary processes in the earth and moon. Chemical yields for the three-stage ion-exchange column procedure average 90% for Hf. Chemical blanks are international mass spectrometric standard; suitable aliquots, prepared from a single batch of JMC 475, are available from Denver. Lu-Hf analyses of the standard rocks BCR-1 and JB-1 are given. The potential of the Lu-Hf method in isotope geochemistry is assessed. ?? 1980 Springer-Verlag.

  4. The magnetic hyperfine field in the 181Ta site in the Co2HfAl and Co2HfGa Heusler alloys

    International Nuclear Information System (INIS)

    Silva, R. da.

    1979-01-01

    The hyperfine magnetic fields at 181 Ta nuclei in Heusler alloys Co 2 HfZ (Z=Al, Ga) have been measured using the time differential perturbed gamma-gamma angular correlation (TDPAC) method. The hyperfine fields obtained from these measurements at the liquid nitrogen temperature are -189 and +- 150 kOersted for Co 2 HfAl and Co 2 HfGa, respectively. The concept that the hyperfine field at the Y site is similar to the solute fields in Fe, Co, Ni and Gd matrices is corroborated. We have verified that ratios H sub(hf) sub(Ta)/T sub(c) and H sub(hf) sub(Ta)μ sub(Co) in Co 2 HfZ compounds (Z=Al, Ga, Sn) do not depend on the nature of Z element. However a dependence in the value of observed field with the s-p element in Z site was noticed. We feel that the samples are not completely ordered cubic as observed by the quadrupole interaction measurements. The results are interpreted in terms of the Campbell-Blandin formalism, and it is shown that the spin polarization of conduction electrons at Hf and Ta have opposite signs. (Author) [pt

  5. Enhanced resistive switching and multilevel behavior in bilayered HfAlO/HfAlO{sub x} structures for non-volatile memory applications

    Energy Technology Data Exchange (ETDEWEB)

    Faita, F. L., E-mail: fabriciofaita@gmail.com [Centre of Physics, University of Minho, Campus de Gualtar, 4710-057 Braga (Portugal); Departamento de Física, Universidade Federal de Santa Catarina, Campus Trindade, 88040-900 Florianópolis, SC (Brazil); Silva, J. P. B., E-mail: josesilva@fisica.uminho.pt [Centre of Physics, University of Minho, Campus de Gualtar, 4710-057 Braga (Portugal); IFIMUP and IN-Institute of Nanoscience and Nanotechnology, Departamento de Física e Astronomia, Faculdade de Ciências da Universidade do Porto, 4169-007 Porto (Portugal); Pereira, M.; Gomes, M. J. M. [Centre of Physics, University of Minho, Campus de Gualtar, 4710-057 Braga (Portugal)

    2015-12-14

    In this work, hafnium aluminum oxide (HfAlO) thin films were deposited by ion beam sputtering deposition technique on Si substrate. The presence of oxygen vacancies in the HfAlO{sub x} layer deposited in oxygen deficient environment is evidenced from the photoluminescence spectra. Furthermore, HfAlO(oxygen rich)/HfAlO{sub x}(oxygen poor) bilayer structures exhibit multilevel resistive switching (RS), and the switching ratio becomes more prominent with increasing the HfAlO layer thickness. The bilayer structure with HfAlO/HfAlO{sub x} thickness of 30/40 nm displays the enhanced multilevel resistive switching characteristics, where the high resistance state/intermediate resistance state (IRS) and IRS/low resistance state resistance ratios are ≈10{sup 2} and ≈5 × 10{sup 5}, respectively. The switching mechanisms in the bilayer structures were investigated by the temperature dependence of the three resistance states. This study revealed that the multilevel RS is attributed to the coupling of ionic conduction and the metallic conduction, being the first associated to the formation and rupture of conductive filaments related to oxygen vacancies and the second with the formation of a metallic filament. Moreover, the bilayer structures exhibit good endurance and stability in time.

  6. Development of Cu-Hf-Al ternary systems and tungsten wire/particle reinforced Cu48Hf43Al9 bulk metallic glass composites for strengthening

    International Nuclear Information System (INIS)

    Park, Joyoung; An, Jihye; Choi-Yim, Haein

    2010-01-01

    Stable bulk glass forming alloys can be developed over a wide range of compositions in Cu-Hf-Al ternary systems starting from the Cu 49 Hf 42 Al 9 bulk metallic glass. Ternary Cu-Hf-Al alloys can be cast directly from the melt into copper molds to form fully amorphous strips with thicknesses of 1 to 6 mm. The maximum critical diameter of the new Cu-Hf-Al ternary alloy was 6 mm. X-ray diffraction patterns were used to confirm the amorphous nature of the ternary Cu-Hf-Al alloys. To increase the toughness of these metallic glasses, we reinforced the Cu 48 Hf 43 Al 9 bulk metallic glass-forming liquid with a 50% volume fraction of tungsten particles and an 80% volume fraction of tungsten wires with diameters of 242.4 μm. Composites with a critical diameter of 7 mm and length 70 mm were synthesized. The structure of the composites was confirmed by using X-ray diffraction (XRD), and the scanning electron microscopy (SEM). The mechanical properties of the composites were studied in compression tests. The thermal stability and the crystallization processes of the Cu-Hf-Al alloys and composites were investigated by using differential scanning calorimetry (DSC). Values of the glass transition temperature (T g ), the crystallization temperature (T x ), and the supercooled liquid region (ΔT = T x - T g ) are given in this paper.

  7. Fretting wear of ZrN and Zr(21% Hf)N coatings

    Energy Technology Data Exchange (ETDEWEB)

    Atar, E. [Gebze Inst. of Tech., Material Science and Engineering Dept., Kocaeli (Turkey); Cimenoglu, H.; Kayali, E.S. [Istanbul Technical Univ., Dept. of Metallurgy and Materials Engineering, Istanbul (Turkey)

    2004-07-01

    In this study, the wear behaviours of ZrN and Zr(21% Hf)N coatings, deposited on hardened AISI D2 cold work tool steel were examined by a fretting wear tester. The hardness of ZrN and Zr(21% Hf)N coatings were almost the same, where as they exhibited different wear resistance. Addition of 21% Hf to ZrN coating achieved about 25% increase in the wear resistance. (orig.)

  8. Fretting wear of ZrN and Zr(21% Hf)N coatings

    International Nuclear Information System (INIS)

    Atar, E.; Cimenoglu, H.; Kayali, E.S.

    2004-01-01

    In this study, the wear behaviours of ZrN and Zr(21% Hf)N coatings, deposited on hardened AISI D2 cold work tool steel were examined by a fretting wear tester. The hardness of ZrN and Zr(21% Hf)N coatings were almost the same, where as they exhibited different wear resistance. Addition of 21% Hf to ZrN coating achieved about 25% increase in the wear resistance. (orig.)

  9. Simultaneous measurements of HF-enhanced plasma waves and artificial field-aligned irregularities at Arecibo

    International Nuclear Information System (INIS)

    Noble, S.T.; Djuth, F.T.

    1990-01-01

    Two radar systems with beams intersecting in the HF-modified F region were used to simultaneously measure HF-enhanced plasma lines (HFPLs) and artificial geomagnetic field-aligned irregularities (AFAIs). The Arecibo 430-MHz radar was used for the HFPL observations, and a portable 49.92-MHz backscatter radar was deployed on the island of Guadeloupe to monitor the AFAIs. The experiment was desgined to examine the degree to which HF-induced plasma turbulence influences the development of AFAIs. When the HF beam is stepped up in power, sustained HFPLs and AFAIs are first observed at the same HF power level, indicating that ponderomotively driven instabilities may be involved in the early time development of AFAIs. As the HF power is increased, the HFPL backscatter power begins to saturate at ∼70 MW effective radiated power (ERP). However, the backscatter from AFAIs is linearly dependent on HF power, even at the highest (120 MW ERP) HF power levels available at Arecibo. This suggests that additional processes may contribute to the development of AFAIs. For example, ponderomotively driven instabilities may give rise to weak geomagnetic field-aligned irregularities that are subsequently driven unstable by processes excited near the upper hybrid resonance. It is also likely that AFAIs greatly impact the development of HF-induced plasma turbulence at late times (>1 s) following HF turn-on. Once the ionosphere is preconditioned by high-power HF modifications, AFAIs and HFPLs can be simultaneously sustained at a much lower HF power level than that needed to originally excite them. The nature of the preconditioning process is currently not well understood. New theoretical initiatives are clearly needed to guide future experimental activity in this area

  10. Assembly of the CMS HF (hadron forward) calorimeter, April 2003 to June 2005

    CERN Multimedia

    Tejinder S. Virdee, CERN

    2005-01-01

    The forward calorimeters (HF) of the CMS hadron calorimeter system are located 11.2 m from the interaction point. Each HF module is composed by 18 wedges, made of steel absorbers and radiation-hard quartz fibers. The photogallery shows the wedges (Figs. 1-3, April 2003), the assembly of one HF module (Figs. 4-9, May and June 2004) and the assembly of the other (Figs. 10-11, June 2005)

  11. Nuclear quadrupole interactions in ferroelectric compounds of HF/sup 181/

    Energy Technology Data Exchange (ETDEWEB)

    Kunzler, J V

    1971-01-01

    Measurements of nuclear quadrupole interaction constants in perovkite-type compounds of PbHfO/sub 3/, SnhfO/sub 3/, CaHfO/sub 3/ e SrHfO/sub 3/ have been performed using the perturbed angular correlation technique. A range of fundamental frequencies from 150 to 550 Megaradians per second was determined. The variation of quadrupole constants has been discussed through the molecular orbital theory.

  12. Small signal gain measurements in a small scale HF overtone laser

    Energy Technology Data Exchange (ETDEWEB)

    Wisniewski, C.F.; Hewett, K.B.; Manke, G.C. II; Hager, G.D. [Air Force Research Laboratory, Directed Energy Directorate, 3550 Aberdeen Ave SE, Kirtland AFB, NM 87117-5776 (United States); Crowell, P.G. [Northrup Grumman Information Technology, Science and Technology Operating Unit, Advanced Technology Division, P.O. Box 9377, Albuquerque, NM 87119-9377 (United States); Truman, C.R. [Mechanical Engineering Department, University of New Mexico, Albuquerque, NM 87131 (United States)

    2003-07-01

    The overtone gain medium of a small-scale HF overtone laser was probed using a sub-Doppler tunable diode laser. Two-dimensional spatially resolved small signal gain and temperature maps were generated for several ro-vibrational transitions in the HF (v=2{yields}v=0) overtone band. Our results compare well with previous measurements of the overtone gain in a similar HF laser device. (orig.)

  13. Reversible spin texture in ferroelectric Hf O2

    Science.gov (United States)

    Tao, L. L.; Paudel, Tula R.; Kovalev, Alexey A.; Tsymbal, Evgeny Y.

    2017-06-01

    Spin-orbit coupling effects occurring in noncentrosymmetric materials are known to be responsible for nontrivial spin configurations and a number of emergent physical phenomena. Ferroelectric materials may be especially interesting in this regard due to reversible spontaneous polarization making possible a nonvolatile electrical control of the spin degrees of freedom. Here, we explore a technologically relevant oxide material, Hf O2 , which has been shown to exhibit robust ferroelectricity in a noncentrosymmetric orthorhombic phase. Using theoretical modelling based on density-functional theory, we investigate the spin-dependent electronic structure of the ferroelectric Hf O2 and demonstrate the appearance of chiral spin textures driven by spin-orbit coupling. We analyze these spin configurations in terms of the Rashba and Dresselhaus effects within the k .p Hamiltonian model and find that the Rashba-type spin texture dominates around the valence-band maximum, while the Dresselhaus-type spin texture prevails around the conduction band minimum. The latter is characterized by a very large Dresselhaus constant λD= 0.578 eV Å, which allows using this material as a tunnel barrier to produce tunneling anomalous and spin Hall effects that are reversible by ferroelectric polarization.

  14. HF Radio Angle-of-Arrival Measurements and Ionosonde Positioning

    Directory of Open Access Journals (Sweden)

    Lung-Chih Tsai

    2014-01-01

    Full Text Available Since 2010 a 2nd generation NOAA MF/HF radar, also referred to as the VIPIR ionosonde, has been operated at Hualien, Taiwan (23.8973°N, 121.5503°E. The Hualien VIPIR ionosonde is a modern ionospheric radar, fully digitizing complex signal records and using multiple parallel receiver channels for simultaneous signal measurements from multiple spaced receiving antennas. This paper considers radio direction finding based on interferometric phase measurements from a horizontal antenna array in the Hualien VIPIR ionosonde system. We applied the Hermite normal form method to solve the phase-measurement aliasing and least squares problems and improve the radio angle-of-arrival (AOA measurements. Backward ray-tracing simulation has been proposed to determine radio transmitter position. This paper presents a numerical, step by step ray-tracing method based on the IGRF superimposed onto a phenomenological ionospheric electron density model, the TaiWan Ionospheric Model (TWIM. The proposed methodology is successfully applied to locate two experimental HF radio transmitters at Longquan and Chungli with distance errors within 5 km and less than 5% of the great circle distances.

  15. HF Radar Sea-echo from Shallow Water

    Directory of Open Access Journals (Sweden)

    Josh Kohut

    2008-08-01

    Full Text Available HF radar systems are widely and routinely used for the measurement of ocean surface currents and waves. Analysis methods presently in use are based on the assumption of infinite water depth, and may therefore be inadequate close to shore where the radar echo is strongest. In this paper, we treat the situation when the radar echo is returned from ocean waves that interact with the ocean floor. Simulations are described which demonstrate the effect of shallow water on radar sea-echo. These are used to investigate limits on the existing theory and to define water depths at which shallow-water effects become significant. The second-order spectral energy increases relative to the first-order as the water depth decreases, resulting in spectral saturation when the waveheight exceeds a limit defined by the radar transmit frequency. This effect is particularly marked for lower radar transmit frequencies. The saturation limit on waveheight is less for shallow water. Shallow water affects second-order spectra (which gives wave information far more than first-order (which gives information on current velocities, the latter being significantly affected only for the lowest radar transmit frequencies for extremely shallow water. We describe analysis of radar echo from shallow water measured by a Rutgers University HF radar system to give ocean wave spectral estimates. Radar-derived wave height, period and direction are compared with simultaneous shallow-water in-situ measurements.

  16. Thermoluminescence in films of HfO2:Dy+3

    International Nuclear Information System (INIS)

    Ceron, P.; Rivera, T.; Guzman, J.; Montes, E.; Pelaez, A.; Rojas, B.; Guzman, D.; Azorin, J.; Paredes, L.

    2014-08-01

    In this work the thermoluminescence (TL) response of films of hafnium oxide polluted with dysprosium (HfO 2 :Dy +3 ) that were irradiated in the near UV (200 nm - 400 nm). The films were deposited by means of the ultrasonics spray pyrolysis technique on a glass substrate, using different deposit temperatures (300 grades C - 600 grades C). The best TL emission corresponded to the prepared film to 450 grades C that was exposed to a spectral irradiation of 80 μJ/(cm 2 -s) with a wave longitude of 240 nm. The TL response in function of the spectral irradiation was lineal in the studied interval (24 to 288 mJ/cm 2 ), several kinetic parameters were also calculated of the shine curve as depth of the trap (E), frequency factor (s) and order to the kinetics (b). The obtained results show that the films of HfO 2 :Dy +3 could be used as radiation monitor in the region of the near UV. (Author)

  17. Pressure-induced phase transformation of HfO2

    International Nuclear Information System (INIS)

    Arashi, H.

    1992-01-01

    This paper reports on the pressure dependence of the Raman spectra of HfO 2 that was measured by a micro-Raman technique using a single-crystal specimen in the pressure range from 0 to 10 GPa at room temperature. The symmetry assignment of Raman bands of the monoclinic phase was experimentally accomplished from the polarization measurements for the single crystal. With increased pressure, a phase transformation for the monoclinic phase took place at 4.3 ± 0.3 GPa. Nineteen Raman bands were observed for the high-pressure phase. The spectral structure of the Raman bands for the high-pressure phase was similar with those reported previously for ZrO 2 . The space group for the high pressure phase of HfO 2 was determined as Pbcm, which was the same as that of the high-pressure phase for ZrO 2 on the basis of the number and the spectral structure of the Raman bands

  18. Soluble Flt-1 links microvascular disease with heart failure in CKD.

    Science.gov (United States)

    Di Marco, Giovana S; Kentrup, Dominik; Reuter, Stefan; Mayer, Anna B; Golle, Lina; Tiemann, Klaus; Fobker, Manfred; Engelbertz, Christiane; Breithardt, Günter; Brand, Eva; Reinecke, Holger; Pavenstädt, Hermann; Brand, Marcus

    2015-05-01

    Chronic kidney disease (CKD) is associated with an increased risk of heart failure (HF). Elevated plasma concentrations of soluble Flt-1 (sFlt-1) have been linked to cardiovascular disease in CKD patients, but whether sFlt-1 contributes to HF in CKD is still unknown. To provide evidence that concludes a pathophysiological role of sFlt-1 in CKD-associated HF, we measured plasma sFlt-1 concentrations in 586 patients with angiographically documented coronary artery disease and renal function classified according to estimated glomerular filtration rate (eGFR). sFlt-1 concentrations correlated negatively with eGFR and were associated with signs of heart failure, based on New York Heart Association functional class and reduced left ventricular ejection fraction (LVEF), and early mortality. Additionally, rats treated with recombinant sFlt-1 showed a 15 % reduction in LVEF and a 29 % reduction in cardiac output compared with control rats. High sFlt-1 concentrations were associated with a 15 % reduction in heart capillary density (number of vessels/cardiomyocyte) and a 24 % reduction in myocardial blood volume. Electron microscopy and histological analysis revealed mitochondrial damage and interstitial fibrosis in the hearts of sFlt-1-treated, but not control rats. In 5/6-nephrectomised rats, an animal model of CKD, sFlt-1 antagonism with recombinant VEGF121 preserved heart microvasculature and significantly improved heart function. Overall, these findings suggest that a component of cardiovascular risk in CKD patients could be directly attributed to sFlt-1. Assessment of patients with CKD confirmed that sFlt-1 concentrations were inversely correlated with renal function, while studies in rats suggested that sFlt-1 may link microvascular disease with HF in CKD.

  19. Effect of tungsten metal particle sizes on the solubility of molten alloy melt: Experimental observation of Gibbs-Thomson effect in nanocomposites

    Science.gov (United States)

    Lee, M. H.; Das, J.; Sordelet, D. J.; Eckert, J.; Hurd, A. J.

    2012-09-01

    We investigated the effect of tungsten particle sizes on the thermal stability and reactivity of uniformly dispersed W particles in molten Hf-based alloy melt at elevated temperature (1673 K). The solubility of particles less than 100 nm in radius is significantly enhanced. In case of fine W particles with 20 nm diameter, their solubility increases remarkably around 700% compared to that of coarse micrometer-scale particles. The mechanisms and kinetics of this dynamic growth of particle are discussed as well as techniques developed to obtain frozen microstructure of particle-reinforced composites by rapid solidification.

  20. Thermodynamic modeling of the Co–Hf system supported by key experiments and first-principles calculations

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Xingxu [School of Materials Science and Engineering, Central South University, Changsha, Hunan 410083 (China); State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Liu, Shuhong, E-mail: shhliu@csu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Sino-German Cooperation Group “Microstructure in Al alloys”, Central South University, Changsha, Hunan 410083 (China); Cheng, Kaiming; Tang, Ying [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Ou, Pengfei [School of Materials Science and Engineering, Central South University, Changsha, Hunan 410083 (China); State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Nash, Philip [Thermal Processing Technology Center, Illinois Institute of Technology (IIT), 10 West 32nd Street, Chicago, IL 60616 (United States); Sundman, Bo [INSTN, CEA Saclay, 91191 Gif-Sur-Yvette Cedex (France); Du, Yong [State Key Laboratory of Powder Metallurgy, Central South University, Changsha, Hunan 410083 (China); Sino-German Cooperation Group “Microstructure in Al alloys”, Central South University, Changsha, Hunan 410083 (China); Zheng, Feng [School of Materials Science and Engineering, Central South University, Changsha, Hunan 410083 (China)

    2015-05-20

    Highlights: • Heat contents of Co{sub 2}Hf and CoHf{sub 2} were measured by drop calorimetry. • Enthalpy of formation for Co{sub 23}Hf{sub 6} was computed via first-principles calculations. • Co–Hf system was assessed by means of CALPHAD approach. • Order–disorder model is used to describe B2 (CoHf) and A2 (βHf). • Glass forming range of the Co–Hf amorphous alloys was predicted. - Abstract: Phase equilibria and thermodynamic properties of the Co–Hf system were investigated via calorimetric measurements, first-principles calculations and thermodynamic modeling. Heat contents of Co{sub 2}Hf and CoHf{sub 2} were measured by drop calorimetry from 300 to 1200 °C. The enthalpy of formation for Co{sub 23}Hf{sub 6} at 0 K was computed via first-principles calculations. Based on the experimental measurements and first-principles calculations from the present work and the literature, the Co–Hf system was assessed by means of CALPHAD (CALculation of PHAse Diagram) approach. The excess Gibbs energy of solution phases was modeled with Redlich–Kister polynomial. Sublattice models were employed to describe the homogeneity ranges of Co{sub 2}Hf, CoHf and CoHf{sub 2}. The order–disorder transition between B2 (CoHf) and A2 (βHf) phases was taken into account in the current optimization. Using the optimized parameters, glass forming range (GFR) of the Co–Hf amorphous alloys was predicted to be 15–75 at.% Hf, which is in satisfactory agreement with the experimental observation.

  1. Study of Direct-Contact HfO2/Si Interfaces

    Directory of Open Access Journals (Sweden)

    Noriyuki Miyata

    2012-03-01

    Full Text Available Controlling monolayer Si oxide at the HfO2/Si interface is a challenging issue in scaling the equivalent oxide thickness of HfO2/Si gate stack structures. A concept that the author proposes to control the Si oxide interface by using ultra-high vacuum electron-beam HfO2 deposition is described in this review paper, which enables the so-called direct-contact HfO2/Si structures to be prepared. The electrical characteristics of the HfO2/Si metal-oxide-semiconductor capacitors are reviewed, which suggest a sufficiently low interface state density for the operation of metal-oxide-semiconductor field-effect-transistors (MOSFETs but reveal the formation of an unexpected strong interface dipole. Kelvin probe measurements of the HfO2/Si structures provide obvious evidence for the formation of dipoles at the HfO2/Si interfaces. The author proposes that one-monolayer Si-O bonds at the HfO2/Si interface naturally lead to a large potential difference, mainly due to the large dielectric constant of the HfO2. Dipole scattering is demonstrated to not be a major concern in the channel mobility of MOSFETs.

  2. Chemical stability and defect formation in CaHfO3

    KAUST Repository

    Alay-E-Abbas, Syed Muhammad

    2014-04-01

    Defects in CaHfO3 are investigated by ab initio calculations based on density functional theory. Pristine and anion-deficient CaHfO 3 are found to be insulating, whereas cation-deficient CaHfO 3 is hole-doped. The formation energies of neutral and charged cation and anion vacancies are evaluated to determine the stability in different chemical environments. Moreover, the energies of the partial and full Schottky defect reactions are computed. We show that clustering of anion vacancies in the HfO layers is energetically favorable for sufficiently high defect concentrations and results in metallicity. © 2014 EPLA.

  3. Chemical stability and defect formation in CaHfO3

    KAUST Repository

    Alay-E-Abbas, Syed Muhammad; Nazir, Safdar; Mun Wong, Kin; Shaukat, Ali; Schwingenschlö gl, Udo

    2014-01-01

    Defects in CaHfO3 are investigated by ab initio calculations based on density functional theory. Pristine and anion-deficient CaHfO 3 are found to be insulating, whereas cation-deficient CaHfO 3 is hole-doped. The formation energies of neutral and charged cation and anion vacancies are evaluated to determine the stability in different chemical environments. Moreover, the energies of the partial and full Schottky defect reactions are computed. We show that clustering of anion vacancies in the HfO layers is energetically favorable for sufficiently high defect concentrations and results in metallicity. © 2014 EPLA.

  4. Surface circulation patterns at the southeastern Bay of Biscay: new observations from HF radar data

    Science.gov (United States)

    Solabarrieta, L.; Rubio, A.; Medina, R.; Paduan, J. D.; Castanedo, S.; Fontán, A.; Cook, M.; González, M.

    2012-12-01

    A CODAR Seasonde High Frequency (HF) radar network has been operational since the beginning of 2009 for the oceanic region of the Basque Country, Spain (south-eastern Bay of Biscay, Atlantic Ocean). It forms part of the Basque operational data acquisition system, established by the Directorate of Emergency Attention and Meteorology of the Basque Government. It is made up of two antennas, at the capes Higer (43d 23.554' N, 1d 47.745' W) and Matxitxako (43d 7.350' N, 2d 45.163' W), emitting at 4.525 MHz frequency and 30 kHz bandwidth. This system provides hourly surface currents with 5.12 km spatial resolution, covering 10,000 km2. Space- and time-covering measurements have been available in the study area since 2009. The data contribute considerably to the study of surface current patterns and the main physical processes in the area. Additional applications relate to security of navigation, maritime rescue, validation and improvement of numerical models, etc. For comparison with other validation studies and to obtain an estimate of the performance of the Basque system, statistical and spectral analysis of the surface currents obtained through the HF radar and different in-situ platforms have been conducted. The analyses show values of comparison between the different measuring systems consistent with those done by other authors (Paduan and Rosenfeld, 1996; Kaplan et al., 2005). The radar is able to reproduce the time evolution of the currents with a reasonable accuracy; likewise, the main three spectral peaks (inertial, semidiurnal and diurnal) are well resolved. In this context, the aim of this work is to show the HF radar ability to measure accurately the surface currents in the south-eastern Bay of Biscay and to study the ocean circulation in the area (figures 1 and 2). Surface current patterns are analysed and described for the period 2009-2011, for different timescales. A clear seasonality at a large-scale has been observed in accordance with previous work

  5. Evolution of E 2 transition strength in deformed hafnium isotopes from new measurements on 172Hf,174Hf, and 176Hf

    Science.gov (United States)

    Rudigier, M.; Nomura, K.; Dannhoff, M.; Gerst, R.-B.; Jolie, J.; Saed-Samii, N.; Stegemann, S.; Régis, J.-M.; Robledo, L. M.; Rodríguez-Guzmán, R.; Blazhev, A.; Fransen, Ch.; Warr, N.; Zell, K. O.

    2015-04-01

    Background: The available data for E 2 transition strengths in the region between neutron-deficient hafnium and platinum isotopes are far from complete. More and precise data are needed to enhance the picture of structure evolution in this region and to test state-of-the-art nuclear models. In a simple model, the maximum collectivity is expected at the middle of the major shell. However, for actual nuclei, particularly in heavy-mass regions, which should be highly complex, this picture may no longer be the case, and one should use a more realistic nuclear-structure model. We address this point by studying the spectroscopy of Hf as a representative case. Purpose: We remeasure the 21+ half-lives of 172,174,176Hf, for which there is some disagreement in the literature. The main goal is to measure, for the first time, the half-lives of higher-lying states of the rotational band. The new results are compared to a theoretical calculation for absolute transition strengths. Method: The half-lives were measured using γ -γ and conversion-electron-γ delayed coincidences with the fast timing method. For the determination of half-lives in the picosecond region, the generalized centroid difference method was applied. For the theoretical calculation of the spectroscopic properties, the interacting boson model is employed, whose Hamiltonian is determined based on microscopic energy-density functional calculations. Results: The measured 21+ half-lives disagree with results from earlier γ -γ fast timing measurements, but are in agreement with data from Coulomb excitation experiments and other methods. Half-lives of the 41+ and 61+ states were measured, as well as a lower limit for the 81+ states. Conclusions: This work shows the importance of a mass-dependent effective boson charge in the interacting boson model for the description of E 2 transition rates in chains of nuclei. It encourages further studies of the microscopic origin of this mass dependence. New experimental

  6. A new potential energy surface for vibration-vibration coupling in HF-HF collisions. Formulation and quantal scattering calculations

    Science.gov (United States)

    Schwenke, David W.; Truhlar, Donald G.

    1988-04-01

    We present new ab initio calculations of the HF-HF interaction potential for the case where both molecules are simultaneously displaced from their equilibrium internuclear distance. These and previous ab initio calculations are then fit to a new analytic representation which is designed to be efficient to evaluate and to provide an especially faithful account of the forces along the vibrational coordinates. We use the new potential for two sets of quantal scattering calculations for collisions in three dimensions with total angular momentum zero. First we test that the angular harmonic representation of the anisotropy is adequate by comparing quantal rigid rotator calculations to those carried out for potentials involving higher angular harmonics and for which the expansion in angular harmonics is systematically increased to convergence. Then we carry out large-scale quantal calculations of vibration-vibration energy transfer including the coupling of both sets of vibrational and rotational coordinates. These calculations indicate that significant rotational energy transfer accompanies the vibration-to-vibration energy transfer process.

  7. Doppler shift simulation of scattered HF signals during the Tromsø HF pumping experiment on 16 February 1996

    Directory of Open Access Journals (Sweden)

    T. D. Borisova

    2002-09-01

    Full Text Available Comparisons between bistatic scatter measurements and simulation results during the Tromsø HF pumping experiment on 16 February 1996 are made. Doppler measurements of an HF diagnostic signal scattered from the field-aligned irregularities (FAIs in the auroral E-region were carried out on the London – Tromsø – St. Petersburg path at 9410 kHz from 21:00 to 22:00 UT. The scattered signals were observed both from natural and artificial ionospheric irregularities located in the vicinity of Tromsø. To simulate the Doppler frequency shifts, fd , of scattered signals, a radio channel model, named CONE, was developed. The model allows for ray tracing, group and phase paths, and Doppler frequency shift calculations. The calculated Doppler shifts were analyzed for dependence on the magnitude and direction of plasma velocities in the scattering volume. It was found that the velocity components in the north-south direction are crucial for explaining the Doppler frequency shifts of the scattered diagnostic signals. To simulate fd , real velocities obtained from the EISCAT UHF radar at an altitude of 278 km and from the digital all-sky imager during the experiment were employed. The simulation results of Doppler frequency shift variations with time are in reasonable agreement with the experimental Doppler shifts of scattered signals on the London – Tromsø – St. Petersburg path.Key words. Ionosphere (active experiments; ionospheric irregularities Radio science (ionospheric propagation

  8. Analysis of the Metal Oxide Space Clouds (MOSC) HF Propagation Environment

    Science.gov (United States)

    Jackson-Booth, N.; Selzer, L.

    2015-12-01

    Artificial Ionospheric Modification (AIM) attempts to modify the ionosphere in order to alter the high frequency (HF) propagation environment. It can be achieved through injections of aerosols, chemicals or radio (RF) signals into the ionosphere. The Metal Oxide Space Clouds (MOSC) experiment was undertaken in April/May 2013 to investigate chemical AIM. Two sounding rockets were launched from the Kwajalein Atoll (part of the Marshall Islands) and each released a cloud of vaporized samarium (Sm). The samarium created a localized plasma cloud, with increased electron density, which formed an additional ionospheric layer. The ionospheric effects were measured by a wide range of ground based instrumentation which included a network of high frequency (HF) sounders. Chirp transmissions were made from three atolls and received at five sites within the Marshall Islands. One of the receive sites consisted of an 18 antenna phased array, which was used for direction finding. The ionograms have shown that as well as generating a new layer the clouds created anomalous RF propagation paths, which interact with both the cloud and the F-layer, resulting in 'ghost traces'. To fully understand the propagation environment a 3D numerical ray trace has been undertaken, using a variety of background ionospheric and cloud models, to find the paths through the electron density grid for a given fan of elevation and azimuth firing angles. Synthetic ionograms were then produced using the ratio of ray path length to speed of light as an estimation of the delay between transmission and observation for a given frequency of radio wave. This paper reports on the latest analysis of the MOSC propagation environment, comparing theory with observations, to further understanding of AIM.

  9. Atomic scale engineering of HfO2-based dielectrics for future DRAM applications

    International Nuclear Information System (INIS)

    Dudek, Piotr

    2011-01-01

    Modern dielectrics in combination with appropriate metal electrodes have a great potential to solve many difficulties associated with continuing miniaturization process in the microelectronic industry. One significant branch of microelectronics incorporates dynamic random access memory (DRAM) market. The DRAM devices scaled for over 35 years starting from 4 kb density to several Gb nowadays. The scaling process led to the dielectric material thickness reduction, resulting in higher leakage current density, and as a consequence higher power consumption. As a possible solution for this problem, alternative dielectric materials with improved electrical and material science parameters were intensively studied by many research groups. The higher dielectric constant allows the use of physically thicker layers with high capacitance but strongly reduced leakage current density. This work focused on deposition and characterization of thin insulating layers. The material engineering process was based on Si cleanroom compatible HfO 2 thin films deposited on TiN metal electrodes. A combined materials science and dielectric characterization study showed that Ba-added HfO 2 (BaHfO 3 ) films and Ti-added BaHfO 3 (BaHf 0.5 Ti 0.5 O 3 ) layers are promising candidates for future generation of state-of-the-art DRAMs. In especial a strong increase of the dielectric permittivity k was achieved for thin films of cubic BaHfO 3 (k∝38) and BaHf 0.5 Ti 0.5 O 3 (k∝90) with respect to monoclinic HfO 2 (k∝19). Meanwhile the CET values scaled down to 1 nm for BaHfO 3 and ∝0.8 nm for BaHf 0.5 Ti 0.5 O 3 with respect to HfO 2 (CET=1.5 nm). The Hf 4+ ions substitution in BaHfO 3 by Ti 4+ ions led to a significant decrease of thermal budget from 900 C for BaHfO 3 to 700 C for BaHf 0.5 Ti 0.5 O 3 . Future studies need to focus on the use of appropriate metal electrodes (high work function) and on film deposition process (homogeneity) for better current leakage control. (orig.)

  10. Reliability assessment of ultra-thin HfO2 films deposited on silicon wafer

    International Nuclear Information System (INIS)

    Fu, Wei-En; Chang, Chia-Wei; Chang, Yong-Qing; Yao, Chih-Kai; Liao, Jiunn-Der

    2012-01-01

    Highlights: ► Nano-mechanical properties on annealed ultra-thin HfO 2 film are studied. ► By AFM analysis, hardness of the crystallized HfO 2 film significantly increases. ► By nano-indention, the film hardness increases with less contact stiffness. ► Quality assessment on the annealed ultra-thin films can thus be achieved. - Abstract: Ultra-thin hafnium dioxide (HfO 2 ) is used to replace silicon dioxide to meet the required transistor feature size in advanced semiconductor industry. The process integration compatibility and long-term reliability for the transistors depend on the mechanical performance of ultra-thin HfO 2 films. The criteria of reliability including wear resistance, thermal fatigue, and stress-driven failure rely on film adhesion significantly. The adhesion and variations in mechanical properties induced by thermal annealing of the ultra-thin HfO 2 films deposited on silicon wafers (HfO 2 /SiO 2 /Si) are not fully understood. In this work, the mechanical properties of an atomic layer deposited HfO 2 (nominal thickness ≈10 nm) on a silicon wafer were characterized by the diamond-coated tip of an atomic force microscope and compared with those of annealed samples. The results indicate that the annealing process leads to the formation of crystallized HfO 2 phases for the atomic layer deposited HfO 2 . The HfSi x O y complex formed at the interface between HfO 2 and SiO 2 /Si, where the thermal diffusion of Hf, Si, and O atoms occurred. The annealing process increases the surface hardness of crystallized HfO 2 film and therefore the resistance to nano-scratches. In addition, the annealing process significantly decreases the harmonic contact stiffness (or thereafter eliminate the stress at the interface) and increases the nano-hardness, as measured by vertically sensitive nano-indentation. Quality assessments on as-deposited and annealed HfO 2 films can be thereafter used to estimate the mechanical properties and adhesion of ultra-thin HfO 2

  11. Reliability assessment of ultra-thin HfO{sub 2} films deposited on silicon wafer

    Energy Technology Data Exchange (ETDEWEB)

    Fu, Wei-En [Center for Measurement Standards, Industrial Technology Research Institute, Room 216, Building 8, 321 Kuang Fu Road Sec. 2, Hsinchu, Taiwan (China); Chang, Chia-Wei [Department of Materials Science and Engineering, National Cheng Kung University, 1 University Road, Tainan 70101, Taiwan (China); Chang, Yong-Qing [Center for Measurement Standards, Industrial Technology Research Institute, Room 216, Building 8, 321 Kuang Fu Road Sec. 2, Hsinchu, Taiwan (China); Yao, Chih-Kai [Department of Materials Science and Engineering, National Cheng Kung University, 1 University Road, Tainan 70101, Taiwan (China); Liao, Jiunn-Der, E-mail: jdliao@mail.ncku.edu.tw [Department of Materials Science and Engineering, National Cheng Kung University, 1 University Road, Tainan 70101, Taiwan (China)

    2012-09-01

    Highlights: Black-Right-Pointing-Pointer Nano-mechanical properties on annealed ultra-thin HfO{sub 2} film are studied. Black-Right-Pointing-Pointer By AFM analysis, hardness of the crystallized HfO{sub 2} film significantly increases. Black-Right-Pointing-Pointer By nano-indention, the film hardness increases with less contact stiffness. Black-Right-Pointing-Pointer Quality assessment on the annealed ultra-thin films can thus be achieved. - Abstract: Ultra-thin hafnium dioxide (HfO{sub 2}) is used to replace silicon dioxide to meet the required transistor feature size in advanced semiconductor industry. The process integration compatibility and long-term reliability for the transistors depend on the mechanical performance of ultra-thin HfO{sub 2} films. The criteria of reliability including wear resistance, thermal fatigue, and stress-driven failure rely on film adhesion significantly. The adhesion and variations in mechanical properties induced by thermal annealing of the ultra-thin HfO{sub 2} films deposited on silicon wafers (HfO{sub 2}/SiO{sub 2}/Si) are not fully understood. In this work, the mechanical properties of an atomic layer deposited HfO{sub 2} (nominal thickness Almost-Equal-To 10 nm) on a silicon wafer were characterized by the diamond-coated tip of an atomic force microscope and compared with those of annealed samples. The results indicate that the annealing process leads to the formation of crystallized HfO{sub 2} phases for the atomic layer deposited HfO{sub 2}. The HfSi{sub x}O{sub y} complex formed at the interface between HfO{sub 2} and SiO{sub 2}/Si, where the thermal diffusion of Hf, Si, and O atoms occurred. The annealing process increases the surface hardness of crystallized HfO{sub 2} film and therefore the resistance to nano-scratches. In addition, the annealing process significantly decreases the harmonic contact stiffness (or thereafter eliminate the stress at the interface) and increases the nano-hardness, as measured by vertically

  12. Atomic scale engineering of HfO{sub 2}-based dielectrics for future DRAM applications

    Energy Technology Data Exchange (ETDEWEB)

    Dudek, Piotr

    2011-02-14

    Modern dielectrics in combination with appropriate metal electrodes have a great potential to solve many difficulties associated with continuing miniaturization process in the microelectronic industry. One significant branch of microelectronics incorporates dynamic random access memory (DRAM) market. The DRAM devices scaled for over 35 years starting from 4 kb density to several Gb nowadays. The scaling process led to the dielectric material thickness reduction, resulting in higher leakage current density, and as a consequence higher power consumption. As a possible solution for this problem, alternative dielectric materials with improved electrical and material science parameters were intensively studied by many research groups. The higher dielectric constant allows the use of physically thicker layers with high capacitance but strongly reduced leakage current density. This work focused on deposition and characterization of thin insulating layers. The material engineering process was based on Si cleanroom compatible HfO{sub 2} thin films deposited on TiN metal electrodes. A combined materials science and dielectric characterization study showed that Ba-added HfO{sub 2} (BaHfO{sub 3}) films and Ti-added BaHfO{sub 3} (BaHf{sub 0.5}Ti{sub 0.5}O{sub 3}) layers are promising candidates for future generation of state-of-the-art DRAMs. In especial a strong increase of the dielectric permittivity k was achieved for thin films of cubic BaHfO{sub 3} (k{proportional_to}38) and BaHf{sub 0.5}Ti{sub 0.5}O{sub 3} (k{proportional_to}90) with respect to monoclinic HfO{sub 2} (k{proportional_to}19). Meanwhile the CET values scaled down to 1 nm for BaHfO{sub 3} and {proportional_to}0.8 nm for BaHf{sub 0.5}Ti{sub 0.5}O{sub 3} with respect to HfO{sub 2} (CET=1.5 nm). The Hf{sup 4+} ions substitution in BaHfO{sub 3} by Ti{sup 4+} ions led to a significant decrease of thermal budget from 900 C for BaHfO{sub 3} to 700 C for BaHf{sub 0.5}Ti{sub 0.5}O{sub 3}. Future studies need to focus

  13. Do Hf isotopes in magmatic zircons represent those of their host rocks?

    Science.gov (United States)

    Wang, Di; Wang, Xiao-Lei; Cai, Yue; Goldstein, Steven L.; Yang, Tao

    2018-04-01

    Lu-Hf isotopic system in zircon is a powerful and widely used geochemical tracer in studying petrogenesis of magmatic rocks and crustal evolution, assuming that zircon Hf isotopes can represent initial Hf isotopes of their parental whole rock. However, this assumption may not always be valid. Disequilibrium partial melting of continental crust would preferentially melt out non-zircon minerals with high time-integrated Lu/Hf ratios and generate partial melts with Hf isotope compositions that are more radiogenic than those of its magma source. Dissolution experiments (with hotplate, bomb and sintering procedures) of zircon-bearing samples demonstrate this disequilibrium effect where partial dissolution yielded variable and more radiogenic Hf isotope compositions than fully dissolved samples. A case study from the Neoproterozoic Jiuling batholith in southern China shows that about half of the investigated samples show decoupled Hf isotopes between zircons and the bulk rocks. This decoupling could reflect complex and prolonged magmatic processes, such as crustal assimilation, magma mixing, and disequilibrium melting, which are consistent with the wide temperature spectrum from ∼630 °C to ∼900 °C by Ti-in-zircon thermometer. We suggest that magmatic zircons may only record the Hf isotopic composition of their surrounding melt during crystallization and it is uncertain whether their Hf isotopic compositions can represent the primary Hf isotopic compositions of the bulk magmas. In this regard, using zircon Hf isotopic compositions to trace crustal evolution may be biased since most of these could be originally from disequilibrium partial melts.

  14. Metal-assisted chemical etching in HF/Na2S2O8 OR HF/KMnO4 produces porous silicon

    NARCIS (Netherlands)

    Hadjersi, T.; Gabouze, N.; Kooij, Ernst S.; Zinine, A.; Zinine, A.; Ababou, A.; Chergui, W.; Cheraga, H.; Belhousse, S.; Djeghri, A.

    2004-01-01

    A new metal-assisted chemical etching method using Na2S2O8 or KMnO4 as an oxidizing agent was proposed to form a porous silicon layer on a highly resistive p-type silicon. A thin layer of Ag or Pd is deposited on the Si(100) surface prior to immersion in a solution of HF and Na2S2O8 or HF and KMnO4.

  15. HfC plasma coating of C/C composites

    International Nuclear Information System (INIS)

    Boncoeur, M.; Schnedecker, G.; Lulewicz, J.D.

    1992-01-01

    The surface properties of C/C composites such as hardness and corrosion or erosion resistance can be modified by a ceramic coating applied by plasma torch. The technique of plasma spraying in controlled temperature and atmosphere, that was developed and patented by the CEA, makes it possible to apply coatings to the majority of metals and ceramics without affecting the characteristics of the composite. An example of hard deposit of HfC on a C/C composite is described. The characteristics of the deposit and of the bonding with the C/C composite were studied before and after a heat treatment under vacuum for 2 hours at 1000 C. 2 refs

  16. Generation and amplification of nanaosecond duration multiline hf laser pulses

    International Nuclear Information System (INIS)

    Getzinger, R.L.; Ware, K.D.; Carpenter, J.P.

    1976-01-01

    High-power, fast-rising pulses of hydrogen fluoride laser energy suitable for laser-fusion target interaction experiments can in principle be generated by directing an electro-optically shuttered oscillator pulse through one or more electron-beam driven amplifiers. A three-stage HF master oscillator-power amplifier (MOPA) configuration was constructed and tested using SF 6 -C 2 H 6 in which an E-O generated 4-ns-FWHM pulse was amplified in an electron-beam-excited third stage and subsequently isolated with a Brewster angle splitter. Independent experiments in which a 100-ns-FWHM pilot pulse interacted with the power amplifier demonstrated for the first time complete extraction of the available laser energy. These two results provide strong evidence that with upgrading to H 2 -F 2 , it should be possible to obtain nanosecond duration pulses with power levels sufficient for meaningful laser fusion target coupling experiments

  17. Ternary ceramic alloys of Zr-Ce-Hf oxides

    Science.gov (United States)

    Becher, P.F.; Funkenbusch, E.F.

    1990-11-20

    A ternary ceramic alloy is described which produces toughening of zirconia and zirconia composites through the stress transformation from tetragonal phase to monoclinic phase. This alloy, having the general formula Ce[sub x]Hf[sub y]Zr[sub 1[minus]x[minus]y]O[sub 2], is produced through the addition of appropriate amounts of ceria and hafnia to the zirconia. Typically, improved toughness is achieved with about 5 to about 15 mol % ceria and up to about 40 mol % hafnia. The preparation of alloys of these compositions are given together with data as to the densities, tetragonal phase content, hardness and fracture toughness. The alloys are useful in preparing zirconia bodies as well as reinforcing ceramic composites. 1 fig.

  18. Updated climatological model predictions of ionospheric and HF propagation parameters

    International Nuclear Information System (INIS)

    Reilly, M.H.; Rhoads, F.J.; Goodman, J.M.; Singh, M.

    1991-01-01

    The prediction performances of several climatological models, including the ionospheric conductivity and electron density model, RADAR C, and Ionospheric Communications Analysis and Predictions Program, are evaluated for different regions and sunspot number inputs. Particular attention is given to the near-real-time (NRT) predictions associated with single-station updates. It is shown that a dramatic improvement can be obtained by using single-station ionospheric data to update the driving parameters for an ionospheric model for NRT predictions of f(0)F2 and other ionospheric and HF circuit parameters. For middle latitudes, the improvement extends out thousands of kilometers from the update point to points of comparable corrected geomagnetic latitude. 10 refs

  19. Silicon/HfO2 interface: Effects of proton irradiation

    International Nuclear Information System (INIS)

    Maurya, Savita; Radhakrishna, M.

    2015-01-01

    Substrate oxide interfaces are of paramount importance in deciding the quality of the semiconductor devices. In this work we have studied how 200 keV proton irradiation affects the interface of a 13 nm thick, atomic layer deposited hafnium dioxide on silicon substrate. Pre- and post-irradiation electrical measurements are used to quantify the effect of proton irradiation for varying electrode geometries. Proton irradiation introduces positive charge in the oxide and at the interface of Si/HfO 2 interface. The gate current is not very much affected under positive injection since the induced positive charge is compensated by the injected electrons. Current voltage characteristics under negative bias get affected by the proton irradiation

  20. Hyperfine spectroscopic study of Laves phase HfFe2

    International Nuclear Information System (INIS)

    Belosevic-Cavor, J.; Novakovic, N.; Cekic, B.; Ivanovic, N.; Manasijevic, M.

    2004-01-01

    Hyperfine fields in HfFe 2 were measured at 181 Ta probe using the time-differential perturbed angular correlation method (TDPAC) in the temperature range 78-1200 K. Analysis of the spectra revealed two interactions with hyperfine fields of 13.82(7) T and 8.0(2) T, at 293 K. First is ascribed to the interaction at the 8a position in the cubic C15 structure. The second can be assigned to a minor amount of hexagonal C14 phase, or to an irregular position of the probe in the C15 lattice. Results of calculations using LAPW-WIEN97 are in a good agreement with experiment

  1. Tsunami Arrival Detection with High Frequency (HF Radar

    Directory of Open Access Journals (Sweden)

    Donald Barrick

    2012-05-01

    Full Text Available Quantitative real-time observations of a tsunami have been limited to deep-water, pressure-sensor observations of changes in the sea surface elevation and observations of sea level fluctuations at the coast, which are essentially point measurements. Constrained by these data, models have been used for predictions and warning of the arrival of a tsunami, but to date no system exists for local detection of an actual incoming wave with a significant warning capability. Networks of coastal high frequency (HF-radars are now routinely observing surface currents in many countries. We report here on an empirical method for the detection of the initial arrival of a tsunami, and demonstrate its use with results from data measured by fourteen HF radar sites in Japan and USA following the magnitude 9.0 earthquake off Sendai, Japan, on 11 March 2011. The distance offshore at which the tsunami can be detected, and hence the warning time provided, depends on the bathymetry: the wider the shallow continental shelf, the greater this time. We compare arrival times at the radars with those measured by neighboring tide gauges. Arrival times measured by the radars preceded those at neighboring tide gauges by an average of 19 min (Japan and 15 min (USA The initial water-height increase due to the tsunami as measured by the tide gauges was moderate, ranging from 0.3 to 2 m. Thus it appears possible to detect even moderate tsunamis using this method. Larger tsunamis could obviously be detected further from the coast. We find that tsunami arrival within the radar coverage area can be announced 8 min (i.e., twice the radar spectral time resolution after its first appearance. This can provide advance warning of the tsunami approach to the coastline locations.

  2. Mapping high-latitude plasma convection with coherent HF radars

    International Nuclear Information System (INIS)

    Ruohoniemi, J.M.; Greenwald, R.A.; Baker, K.B.; Villain, J.-P.; Hanuise, C.; Kelly, J.

    1989-01-01

    In this decade, a new technique for the study of ionosphere electrodynamics has been implemented in an evolving generation of high-latitude HF radars. Coherent backscatter from electron density irregularities at F region altitudes is utilized to observe convective plasma motion. The electronic beam forming and scanning capabilities of the radars afford an excellent combination of spatial (∼50 km) and temporal (∼1 min) resolution of the large-scale (∼10 6 km 2 ) convection pattern. In this paper, we outline the methods developed to synthesize the HF radar data into two-dimensional maps of convection velocity. Although any single radar can directly measure only the line-of-sight, or radial, component of the plasma motion, the convection pattern is sometimes so uniform and stable that scanning in azimuth serves to determine the transverse component as well. Under more variable conditions, data from a second radar are necessary to unambiguously resolve velocity vectors. In either case, a limited region of vector solution can be expanded into contiguous areas of single-radar radial velocity data by noting that the convection must everywhere be divergence-free, i.e., ∇·v=0. It is thus often possible to map velocity vectors without extensive second-radar coverage. We present several examples of two-dimensional velocity maps. These show instances of L shell-aligned flow in the dusk sector, the reversal of convection near magnetic midnight, and counterstreaming in the dayside cleft. We include a study of merged coherent and incoherent radar data that illustrates the applicability of these methods to other ionospheric radar systems. copyright American Geophysical Union 1989

  3. A novel process for preparation of titanium dioxide from Ti-bearing electric furnace slag: NH4HF2-HF leaching and hydrolyzing process.

    Science.gov (United States)

    Zheng, Fuqiang; Guo, Yufeng; Qiu, Guanzhou; Chen, Feng; Wang, Shuai; Sui, Yulei; Jiang, Tao; Yang, Lingzhi

    2018-02-15

    A novel process to prepare titanium dioxide from Ti-bearing electric furnace slag by NH 4 HF 2 -HF leaching and hydrolyzing process has been developed. In this present study, the effects of [NH 4 + ]/[F] mXolar ratio, leaching temperature, [F] concentration, liquid/solid mass ratio, leaching time on the Ti extraction, and the phase transformations have been investigated to reveal the leaching mechanism of Ti-bearing electric furnace slag in NH 4 HF 2 -HF solution. In the NH 4 HF 2 -HF leaching process, the MgTi 2 O 5 and Al 2 TiO 5 are converted to TiF 6 2- and Mg-Al-bearing precipitate. Ti extraction rate reached 98.84% under the optimal conditions. In addition, 98.25% iron ions can be removed in the presence of NaCl prior to hydrolysis process. The effects of pH and temperature on the selective hydrolysis of TiF 6 2- during hydrolysis process were also studied. In the hydrolysis process, the TiF 6 2- is converted to (NH 4 ) 2 TiOF 4 . By calcination, high grade TiO 2 powder with its purity of 99.88% was obtained, using which the products, well crystallized anatase and rutile, were obtained through roasting at 800°C and 1000°C, respectively. Copyright © 2017 Elsevier B.V. All rights reserved.

  4. Observed and simulated time evolution of HCl, ClONO2, and HF total column abundances

    Directory of Open Access Journals (Sweden)

    B.-M. Sinnhuber

    2012-04-01

    measurement and model time series data, with a focus on the time range 2000–2009. This period is chosen because from most of the measurement sites taking part in this study, data are available during these years. The precision of the trends is estimated with the bootstrap resampling method. The sensitivity of the trend results with respect to the fitting function, the time of year chosen and time series length is investigated, as well as a bias due to the irregular sampling of the measurements. The measurements and model results investigated here agree qualitatively on a decrease of the chlorine species by around 1% yr−1. The models simulate an increase of HF of around 1% yr−1. This also agrees well with most of the measurements, but some of the FTIR series in the Northern Hemisphere show a stabilisation or even a decrease in the last few years. In general, for all three gases, the measured trends vary more strongly with latitude and hemisphere than the modelled trends. Relative to the FTIR measurements, the models tend to underestimate the decreasing chlorine trends and to overestimate the fluorine increase in the Northern Hemisphere. At most sites, the models simulate a stronger decrease of ClONO2 than of HCl. In the FTIR measurements, this difference between the trends of HCl and ClONO2 depends strongly on latitude, especially in the Northern Hemisphere.

  5. The first HF table, after heat treatment and ready to be machined in HEPCO, Arak (IRAN)

    CERN Multimedia

    Tiziano Camporesi

    2003-01-01

    The first HF support table 'load' tested by the team of people who have contributed to it from design to welding. This table will support the 240 tons of 1 HF detector and will integrate the raisers which will push it up to the beam line level. It is the first Iranian contribution to an HEP experiment.

  6. Phase transformation and precipitation in aged Ti-Ni-Hf high-temperature shape memory alloys

    International Nuclear Information System (INIS)

    Meng, X.L.; Cai, W.; Zheng, Y.F.; Zhao, L.C.

    2006-01-01

    More attention has been paid to ternary Ti-Ni-Hf high-temperature shape memory alloys (SMAs) due to their high phase transformation temperatures, good thermal stability and low cost. However, the Ti-Ni-Hf alloys have been found to have low ductility and only about 3% shape memory effect and these have hampered their applications. It is well known that there are three methods to improve the shape memory properties of high-temperature SMAs: (a) cold rolling + annealing; (b) adding another element to the alloy; (c) aging. These methods are not suitable to improve the properties of Ti-Ni-Hf alloys. In this paper, a method of conditioning Ni-rich Ti-Ni-Hf alloys as high-temperature SMAs by aging is presented. For Ni-rich Ti 80-x Ni x Hf 20 alloys (numbers indicate at.%) the phase transformation temperatures are on average increased by more than 100 K by aging at 823 K for 2 h. Especially for those alloys with Ni contents less than 50.6 at.%, the martensitic transformation start temperatures (M s ) are higher than 473 K after aging. Transmission electron microscopy shows the presence of (Ti + Hf) 3 Ni 4 precipitates after aging. Compared with the precipitation of Ti 3 Ni 4 particles in Ni-rich Ti-Ni alloys, the precipitation of (Ti + Hf) 3 Ni 4 particles in Ni-rich Ti-Ni-Hf alloys needs higher temperatures and longer times

  7. First results on the sorption behaviour of Rutherfordium from HCl/HF containing aqueous solution

    Energy Technology Data Exchange (ETDEWEB)

    Schumann, D.; Nitsche, H. [Technische Univ. Dresden (Germany); Taut, S. [Forschungszentrum Rossendorf e.V. (FZR), Dresden (Germany); Jost, D.T.; Gaeggeler, H.W. [Paul Scherrer Inst. (PSI), Villigen (Switzerland); Yakushev, A.B.; Buklanov, G.V.; Domanov, V.P.; Lien Din Thi [Joint Inst. for Nuclear Research, Dubna (Russian Federation); Kubica, B.; Misiak, R.; Szeglowski, Z. [NINP Cracow (Poland)

    1997-09-01

    Rutherfordium shows strong sorption on the cation exchanger DOWEX 50x8 at a concentration of 0.1 M HCl/10{sup -2} M HF. This shows that Rf behaves under these conditions differently from Hf and Zr and more like Th under these conditions. (author) 1 fig., 5 refs.

  8. EURObservational Research Programme: the Heart Failure Pilot Survey (ESC-HF Pilot)

    DEFF Research Database (Denmark)

    Maggioni, Aldo P; Dahlström, Ulf; Filippatos, Gerasimos

    2010-01-01

    The primary objective of the new ESC-HF Pilot Survey was to describe the clinical epidemiology of outpatients and inpatients with heart failure (HF) and the diagnostic/therapeutic processes applied across 12 participating European countries. This pilot study was specifically aimed at validating...

  9. Decolourization and degradation of azo Dye, Synozol Red HF6BN ...

    African Journals Online (AJOL)

    Decolourization and degradation of azo Dye, Synozol Red HF6BN, by Pleurotus ostreatus. Sidra Ilyas, Skinder Sultan Sultan, Abdul Rehman. Abstract. The present paper focuses on the use of fungus, Pleurotus ostreatus, to decolorize and degrade azo dye, Synazol Red HF6BN. Decolorization study showed that P.

  10. New PWM method and commutation strategy for HF-link converters for fuel cells and photovoltaics

    DEFF Research Database (Denmark)

    Ljusev, Petar; Andersen, Michael Andreas E.

    2005-01-01

    This paper presents a new PWM method and commutation strategy for HF-link converters, which leads to safe commutation of the load current in the output bidirectional bridge. The proposed implementation is independent of the particular HF-link converter topology and bidirectional switch selection ...

  11. EURObservational Research Programme : The Heart Failure Pilot Survey (ESC-HF Pilot)

    NARCIS (Netherlands)

    Maggioni, Aldo P.; Dahlstrom, Ulf; Filippatos, Gerasimos; Chioncel, Ovidiu; Crespo Leiro, Marisa; Drozdz, Jaroslaw; Fruhwald, Friedrich; Gullestad, Lars; Logeart, Damien; Metra, Marco; Parissis, John; Persson, Hans; Ponikowski, Piotr; Rauchhaus, Mathias; Voors, Adriaan A.; Nielsen, Olav Wendelboe; Zannad, Faiez; Tavazzi, Luigi

    2010-01-01

    The primary objective of the new ESC-HF Pilot Survey was to describe the clinical epidemiology of outpatients and inpatients with heart failure (HF) and the diagnostic/therapeutic processes applied across 12 participating European countries. This pilot study was specifically aimed at validating the

  12. Torsemide Versus Furosemide in Patients With Acute Heart Failure (from the ASCEND-HF Trial)

    NARCIS (Netherlands)

    Mentz, Robert J.; Hasselblad, Vic; DeVore, Adam D.; Metra, Marco; Voors, Adriaan A.; Armstrong, Paul W.; Ezekowitz, Justin A.; Tang, W. H. Wilson; Schulte, Phillip J.; Anstrom, Kevin J.; Hernandez, Adrian F.; Velazquez, Eric J.; O'Connor, Christopher M.

    2016-01-01

    Furosemide is the most commonly used loop diuretic in patients with heart failure (HF) despite data suggesting potential pharmacologic and antifibrotic benefits with torsemide. We investigated patients with HF in Acute Study of Clinical Effectiveness of Nesiritide in Decompensated Heart Failure who

  13. Mechanical properties of ultra-thin HfO2 films studied by nano scratches tests

    International Nuclear Information System (INIS)

    Fu, Wei-En; Chang, Yong-Qing; Chang, Chia-Wei; Yao, Chih-Kai; Liao, Jiunn-Der

    2013-01-01

    10-nm-thick atomic layer deposited HfO 2 films were characterized in terms of wear resistance and indentation hardness to investigate the thermal annealing induced impacts on mechanical properties. The wear resistance of ultra-thin films at low loads was characterized using nano-scratch tests with an atomic force microscope. The depth of the nano-scratches decreases with increasing annealing temperature, indicating that the hardness of the annealed films increases with the annealing temperatures. Surface nanoindentation was also performed to confirm the nanoscratch test results. The hardness variation of the annealed films is due to the generation of HfSi x O y induced by the thermal annealing. X-ray photoelectron spectroscopy measurements proved that the hardness of formed HfSi x O y with increasing annealing temperatures. The existence of HfSi x O y broadens the interface, and causes the increase of the interfacial layer thickness. As a result, the surface hardness increases with the increasing HfSi x O y induced by the thermal annealing. - Highlights: ► Mechanical properties of HfO 2 films were assessed by nano-scratch and indentation. ► Scratch depth of HfO 2 films decreased with the increase of annealing temperatures. ► Nano-hardness of HfO 2 films increased with the increase of annealing temperatures

  14. Nanomechanical study of amorphous and polycrystalline ALD HfO2 thin films

    Science.gov (United States)

    K. Tapily; J.E. Jakes; D. Gu; H. Baumgart; A.A. Elmustafa

    2011-01-01

    Thin films of hafnium oxide (HfO2) were deposited by atomic layer deposition (ALD). The structural properties of the deposited films were characterised by transmission electron microscopy (TEM) and X-ray diffraction (XRD). We investigated the effect of phase transformations induced by thermal treatments on the mechanical properties of ALD HfO

  15. Helium implanted AlHf as studied by 181 Ta TDPAC

    Indian Academy of Sciences (India)

    Measurements on helium implanted sample indicate the binding of helium associated defects by Hf solute clusters. Isochronal annealing measurements indicate the dissociation of the helium implantation induced defects from Hf solute clusters for annealing treatments beyond 650 K. On comparison of the present results ...

  16. Nanosuspension Technology for Solubilizing Poorly Soluble Drugs

    OpenAIRE

    Deoli Mukesh

    2012-01-01

    Poor water solubility for many drugs and drug candidates remains a major obstacle to their development and clinical application. It is estimated that around 40% of drugs in the pipeline cannot be delivered through the preferred route or in some cases, at all owing to poor water solubility. Conventional formulations to improve solubility suffer from low bioavailability and poor pharmacokinetics, with some carriers rendering systemic toxicities (e.g. Cremophor1 EL). To date, nanoscale systems f...

  17. Suspended HfO2 photonic crystal slab on III-nitride/Si platform

    International Nuclear Information System (INIS)

    Wang, Yongjin; Feng, Jiao; Cao, Ziping; Zhu, Hongbo

    2014-01-01

    We present here the fabrication of suspended hafnium oxide (HfO 2 ) photonic crystal slab on a III-nitride/Si platform. The calculations are performed to model the suspended HfO 2 photonic crystal slab. Aluminum nitride (AlN) film is employed as the sacrificial layer to form air gap. Photonic crystal patterns are defined by electron beam lithography and transferred into HfO 2 film, and suspended HfO 2 photonic crystal slab is achieved on a III-nitride/Si platform through wet-etching of AlN layer in the alkaline solution. The method is promising for the fabrication of suspended HfO 2 nanostructures incorporating into a III-nitride/Si platform, or acting as the template for epitaxial growth of III-nitride materials. (orig.)

  18. Soluble theory with massive ghosts

    International Nuclear Information System (INIS)

    Pisarski, R.D.

    1983-01-01

    To investigate the unitarity of asymptotically free, higher-derivative theories, like certain models of quantum gravity, I study a prototype in two space-time dimensions. The prototype is a kind of higher-derivative nonlinear sigma model; it is asymptotically free, exhibits dimensional transmutation, and is soluble in a large-N expansion. The S-matrix elements, constructed from the analytic continuation of the Euclidean Green's functions, conserve probability to approx.O(N -1 ), but violate unitarity at approx.O(N -2 ). The model demonstrates that in higher-derivative theories unitarity, or the lack thereof, cannot be decided without explicit control over the infrared limit. Even so, the results suggest that there may exist some (rather special) asymptotically free, higher-derivative theories which are unitary

  19. Retrograde curves of solidus and solubility

    International Nuclear Information System (INIS)

    Vasil'ev, M.V.

    1979-01-01

    The investigation was concerned with the constitutional diagrams of the eutectic type with ''retrograde solidus'' and ''retrograde solubility curve'' which must be considered as diagrams with degenerate monotectic transformation. The solidus and the solubility curves form a retrograde curve with a common retrograde point representing the solubility maximum. The two branches of the Aetrograde curve can be described with the aid of two similar equations. Presented are corresponding equations for the Cd-Zn system and shown is the possibility of predicting the run of the solubility curve

  20. Synthesis and spectral properties of axially substituted zirconium(IV) and hafnium(IV) water soluble phthalocyanines in solutions

    International Nuclear Information System (INIS)

    Gerasymchuk, Y.S.; Volkov, S.V.; Chernii, V.Ya.; Tomachynski, L.A.; Radzki, St.

    2004-01-01

    Methods of synthesis of novel water soluble axially substituted Zr(IV) and Hf(IV) phthalocyanines with gallic, 5-sulfosalicyllic, oxalic acids, and methyl ester of gallic acid as axial ligands coordinated to the central atom metal of phthalocyanine are presented. The absorption spectra of complex solutions in various solvents were characterized. The dependence of the spectral red shift from Reichardt's empirical polarity parameter is described. The deviation from the linearity of Beer-Bouguer-Lambert law was investigated for the range of concentration 5x10 -6 to 10x10 -5 M. Fluorescent properties of axially substituted phthalocyaninato metal complexes in DMSO solutions were investigated

  1. Doppler shift simulation of scattered HF signals during the Tromsø HF pumping experiment on 16 February 1996

    Directory of Open Access Journals (Sweden)

    T. D. Borisova

    Full Text Available Comparisons between bistatic scatter measurements and simulation results during the Tromsø HF pumping experiment on 16 February 1996 are made. Doppler measurements of an HF diagnostic signal scattered from the field-aligned irregularities (FAIs in the auroral E-region were carried out on the London – Tromsø – St. Petersburg path at 9410 kHz from 21:00 to 22:00 UT. The scattered signals were observed both from natural and artificial ionospheric irregularities located in the vicinity of Tromsø. To simulate the Doppler frequency shifts, fd , of scattered signals, a radio channel model, named CONE, was developed. The model allows for ray tracing, group and phase paths, and Doppler frequency shift calculations. The calculated Doppler shifts were analyzed for dependence on the magnitude and direction of plasma velocities in the scattering volume. It was found that the velocity components in the north-south direction are crucial for explaining the Doppler frequency shifts of the scattered diagnostic signals. To simulate fd , real velocities obtained from the EISCAT UHF radar at an altitude of 278 km and from the digital all-sky imager during the experiment were employed. The simulation results of Doppler frequency shift variations with time are in reasonable agreement with the experimental Doppler shifts of scattered signals on the London – Tromsø – St. Petersburg path.

    Key words. Ionosphere (active experiments; ionospheric irregularities Radio science (ionospheric propagation

  2. Real-time, high frequency (1 Hz), in situ measurement of HCl and HF gases in volcanic plumes with a novel cavity-enhanced, laser-based instrument

    Science.gov (United States)

    Kelly, P. J.; Sutton, A. J.; Elias, T.; Kern, C.; Clor, L. E.; Baer, D. S.

    2017-12-01

    Primary magmatic halogen-containing gases (HCl, HF, HBr, HI in characteristic order of abundance) are of great interest for volcano monitoring and research because, in general, they are more soluble in magma than other commonly-monitored volcanic volatiles (e.g. CO2, SO2, H2S) and thereby can offer unique insights into shallow magmatic processes. Nevertheless, difficulties in obtaining observations of primary volcanic halogens in gas plumes with traditional methods (e.g. direct sampling, Open-Path Fourier Transform Infrared spectroscopy, filter packs) have limited the number of observations reported worldwide, especially from explosive arc volcanoes. With this in mind, the USGS and Los Gatos Research, Inc. collaborated to adapt a commercially-available industrial in situ HCl-HF analyzer for use in airborne and ground-based measurements of volcanic gases. The new, portable instrument is based around two near-IR tunable diode lasers and uses a vibration-tolerant, enhanced-cavity approach that is well-suited for rugged field applications and yields fast (1 Hz) measurements with a wide dynamic range (0 -2 ppm) and sub-ppb precision (1σ: HCl: <0.4 ppb; HF: <0.1 ppb). In spring 2017 we conducted field tests at Kīlauea Volcano, Hawaii, to benchmark the performance of the new instrument and to compare it with an accepted method for halogen measurements (OP-FTIR). The HCl-HF instrument was run in parallel with a USGS Multi-GAS to obtain in situ H2O-CO2-SO2-H2S-HCl-HF plume compositions. The results were encouraging and quasi-direct comparisons of the in situ and remote sensing instruments showed good agreement (e.g. in situ SO2/HCl = 72 vs. OP-FTIR SO2/HCl = 88). Ground-based and helicopter-based measurements made 0 - 12 km downwind from the vent (plume age 0 - 29 minutes) show that plume SO2/HCl ratios increase rapidly from 60 to 300 around the plume edges, possibly due to uptake of HCl onto aerosols.

  3. U Pb and Lu Hf isotope record of detrital zircon grains from the Limpopo Belt Evidence for crustal recycling at the Hadean to early-Archean transition

    Science.gov (United States)

    Zeh, Armin; Gerdes, Axel; Klemd, Reiner; Barton, J. M., Jr.

    2008-11-01

    Detrital zircon grains from Beit Bridge Group quartzite from the Central Zone of the Limpopo Belt near Musina yield mostly ages of 3.35-3.15 Ga, minor 3.15-2.51 Ga components, and numerous older grains grouped at approximately 3.4, 3.5 and 3.6 Ga. Two grains yielded concordant Late Hadean U-Pb ages of 3881 ± 11 Ma and 3909 ± 26 Ma, which are the oldest zircon grains so far found in Africa. The combined U-Pb and Lu-Hf datasets and field relationships provide evidence that the sedimentary protolith of the Beit Bridge Group quartzite was deposited after the emplacement of the Sand River Gneisses (3.35-3.15 Ga), but prior to the Neoarchean magmatic-metamorphic events at 2.65-2.60 Ga. The finding of abundant magmatic zircon detritus with concordant U-Pb ages of 3.35-3.15 Ga, and 176Hf/ 177Hf of 0.28066 ± 0.00004 indicate that the Sand River Gneiss-type rocks were a predominant source. In contrast, detrital zircon grains older than approximately 3.35 Ga were derived from the hinterland of the Limpopo Belt; either from a so far unknown crustal source in southern Africa, possibly from the Zimbabwe Craton and/or a source, which was similar but not necessarily identical to the one that supplied the Hadean zircons to Jack Hills, Western Australia. The Beit Bridge Group zircon population at >3.35 Ga shows a general ɛHf t increase with decreasing age from ɛHf 3.9Ga = -6.3 to ɛHf 3.3-3.1Ga = -0.2, indicating that Hadean crust older than 4.0 Ga ( TDM = 4.45-4.36 Ga) was rejuvenated during magmatic events between >3.9 and 3.1 Ga, due to a successive mixing of crustal rocks with mantle derived magmas. The existence of a depleted mantle reservoir in the Limpopo's hinterland is reflected by the ˜3.6 Ga zircon population, which shows ɛHf 3.6Ga between -4.6 and +3.2. In a global context, our data suggest that a long-lived, mafic Hadean protocrust with some tonalite-trondhjemite-granodiorite constituents was destroyed and partly recycled at the Hadean/Archean transition, perhaps

  4. The Thermodynamic Characterization of ZrCo–H, HfCo−H, HfNi−H and Zr{sub 1–x}HfxNi(Co) Alloy–H Systems

    Energy Technology Data Exchange (ETDEWEB)

    Flanagan, Ted B., E-mail: ted.flanagan@uvm.edu; Noh, Hak; Luo, Suifang

    2016-08-25

    ZrCo and HfCo intermetallic compounds have the same cubic (CsCl-type) structure and their ternary (Zr{sub 1−x}Hf{sub x})Co alloys are also cubic. ZrNi and HfNi intermetallic compounds have the orthorhombic structure (CrB-type) and the ternary (Zr{sub 1−x}Hf{sub x})Ni alloys also have this structure. Thermodynamic data for hydride formation and decomposition in ZrCo, HfCo and HfNi intermetallic compounds have been determined from reaction calorimetry and from pressure-composition isotherms. Thermodynamic data have been determined for the three ternary alloys: (Zr{sub 0.75}Hf{sub 0.25})Co, (Zr{sub 0.50}Hf{sub 0.50})Co, and (Zr{sub 0.25}Hf{sub 0.75})Co and the four ternary alloys: (Zr{sub 0.875}Hf{sub 0.125})Ni, (Zr{sub 0.75}Hf{sub 0.25})Ni, (Zr{sub 0.50}Hf{sub 0.50})Ni, and (Zr{sub 0.25}Hf{sub 0.75})Ni. This offers the opportunity to learn how the thermodynamic properties of the ternary alloy-H systems change with the stoichiometry of alloys with the same structure. - Highlights: • Calorimetric enthalpies determined for H absorption by ZrCo, HfCo, HfNi are determined. • Ternary alloys, e.g., Zr{sub 1−x}Hf{sub x}Ni, prepared and characterized by x-ray diffraction. • Isotherms for the ternary alloys give thermodynamic parameters for H solution.

  5. Soluble FLT-1 rules placental destiny.

    Science.gov (United States)

    Yamashita, Michiko; Kumasawa, Keiichi; Nakamura, Hitomi; Kimura, Tadashi

    2018-02-19

    Placenta previa is an abnormality in which the placenta covers the internal uterine os, and it can cause serious morbidity and mortality in both mother and fetus due to catastrophic hemorrhage. Some pregnant women recover from placenta previa due to a phenomenon called "migration." However, the mechanism of "migration" of the placenta has not been elucidated. Human placentas were collected from patients with placenta previa and those with no abnormal placentation (control). A microarray analysis was performed to detect the genes up- or down-regulated only in the caudal part in the previa group. Specific mRNA expression was evaluated using real-time quantitative reverse transcription PCR (qRT-PCR). Unilateral uterine artery ablation of 8.5 dpc mice was performed to reproduce the reduction of placental blood supply, and weights of the placentas and fetuses were evaluated in 18.5 dpc. Specific mRNA expression was also evaluated in mice placentas. According to the result of the microarray analysis, we focused on soluble fms-like tyrosine kinase-1 (sFLT-1) and hypoxia-inducible factor-1 (HIF-1) alpha. The sFLT-1 expression level is locally high in the caudal part of the human placenta in patients with placenta previa. In mice experiments, the weights of the placentas and fetuses were significantly smaller in the ablation side than those in the control side, and the sFlt-1 expression level was significantly higher in the ablation side than in the control side. Our study suggests that "migration" of the placenta is derived from placental degeneration at the caudal part of the placenta, and sFlt-1 plays a role in this placental degeneration. Copyright © 2018 Elsevier Inc. All rights reserved.

  6. Oxidation behavior of TiC, ZrC, and HfC dispersed in oxide matrices

    International Nuclear Information System (INIS)

    Arun, R.; Subramanian, M.; Mehrotra, G.M.

    1990-01-01

    The oxidation behavior of hot pressed TiC-Al 2 O 3 , TiC-ZrO 2 , ZrC-ZrO 2 , and HfC-HfO 2 composites has been investigated at 1273 K. The oxidation of TiC, ZrC, and HfC in hot-pressed composites containing ZrO 2 and HfO 2 has been found to be extremely rapid. The kinetics of oxidation of TiC and a 90 wt% TiC-Al 2 O 3 composite appear to be faster compared to that of pure TiC. X-ray diffraction results for hot-pressed ZrC-HfO 2 and HfC-HfO 2 composites indicate partial stabilization of tetragonal ZrO 2 and HfO 2 phases in these composites

  7. Structure, optical properties and thermal stability of HfErO films deposited by simultaneous RF and VHF magnetron sputtering

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, H.Y. [Soochow University, College of Physics, Optoelectronics and Energy and Collaborative Innovation Center of Suzhou Nano Science and Technology, Suzhou (China); Nanjing University of Posts and Telecommunications, School of Tongda, Nanjing (China); Soochow University, Key Lab of Advanced Optical Manufacturing Technologies of Jiangsu Province and Key Lab of Modern Optical Technologies of Education Ministry of China, Suzhou (China); He, H.J.; Zhang, Z.; Jin, C.G.; Yang, Y.; Wang, Y.Y.; Ye, C. [Soochow University, College of Physics, Optoelectronics and Energy and Collaborative Innovation Center of Suzhou Nano Science and Technology, Suzhou (China); Soochow University, Key Lab of Advanced Optical Manufacturing Technologies of Jiangsu Province and Key Lab of Modern Optical Technologies of Education Ministry of China, Suzhou (China); Zhuge, L.J. [Soochow University, Key Lab of Advanced Optical Manufacturing Technologies of Jiangsu Province and Key Lab of Modern Optical Technologies of Education Ministry of China, Suzhou (China); Soochow University, Analysis and Testing Center, Suzhou (China); Wu, X.M. [Soochow University, College of Physics, Optoelectronics and Energy and Collaborative Innovation Center of Suzhou Nano Science and Technology, Suzhou (China); Soochow University, Key Lab of Advanced Optical Manufacturing Technologies of Jiangsu Province and Key Lab of Modern Optical Technologies of Education Ministry of China, Suzhou (China); Chinese Academy of Sciences, State Key Laboratory of Functional Materials for Informatics, Shanghai Institute of Microsystem and Information Technology, Shanghai (China)

    2015-01-23

    HfErO films are deposited on Si substrates by simultaneous radio frequency (RF) and very high frequency (VHF) magnetron sputtering technique. The content of the doped ingredient of Er and the body composition of HfO{sub x} are, respectively, controlled through the VHF and RF powers. Low content of Er doping in the HfErO films can be achieved, because the VHF source of 27.12 MHz has higher ion energy and lower ion flux than the RF source resulting in low sputtering rate in the magnetron sputtering system. The structure, optical properties and thermal stability of the HfErO films are investigated in this work. Results show that the doped content of Er is independently controlled by the VHF power. The oxygen vacancies are created by the Er incorporation. The hafnium in the HfErO films forms mixed valence of Hf{sup 2+} and Hf{sup 4+}. The HfErO films are composed with the structures of HfO{sub 2}, HfO and ErO{sub x}, which can be optimized through the VHF power. At high VHF power, the Hf-Er-O bonds are formed, which demonstrates that the Er atoms are doped into the lattice of HfO{sub 2} in the HfErO films. The HfErO films have bad thermal stability as the crystallization temperature decreases from 900 to 800 C. After thermal annealing, cubic phase of HfO{sub 2} are stabilized, which is ascribed to the oxygen vacancies creation by the Er incorporation. The optical properties such as the refractive index and the optical band gap of the HfErO films are optimized by the VHF power. (orig.)

  8. Structure, optical properties and thermal stability of HfErO films deposited by simultaneous RF and VHF magnetron sputtering

    International Nuclear Information System (INIS)

    Zhang, H.Y.; He, H.J.; Zhang, Z.; Jin, C.G.; Yang, Y.; Wang, Y.Y.; Ye, C.; Zhuge, L.J.; Wu, X.M.

    2015-01-01

    HfErO films are deposited on Si substrates by simultaneous radio frequency (RF) and very high frequency (VHF) magnetron sputtering technique. The content of the doped ingredient of Er and the body composition of HfO x are, respectively, controlled through the VHF and RF powers. Low content of Er doping in the HfErO films can be achieved, because the VHF source of 27.12 MHz has higher ion energy and lower ion flux than the RF source resulting in low sputtering rate in the magnetron sputtering system. The structure, optical properties and thermal stability of the HfErO films are investigated in this work. Results show that the doped content of Er is independently controlled by the VHF power. The oxygen vacancies are created by the Er incorporation. The hafnium in the HfErO films forms mixed valence of Hf 2+ and Hf 4+ . The HfErO films are composed with the structures of HfO 2 , HfO and ErO x , which can be optimized through the VHF power. At high VHF power, the Hf-Er-O bonds are formed, which demonstrates that the Er atoms are doped into the lattice of HfO 2 in the HfErO films. The HfErO films have bad thermal stability as the crystallization temperature decreases from 900 to 800 C. After thermal annealing, cubic phase of HfO 2 are stabilized, which is ascribed to the oxygen vacancies creation by the Er incorporation. The optical properties such as the refractive index and the optical band gap of the HfErO films are optimized by the VHF power. (orig.)

  9. Determination of soluble protein contents from RVNRL

    International Nuclear Information System (INIS)

    Wan Manshol Wan Zin; Nurulhuda Othman

    1996-01-01

    This project was carried out to determine the soluble protein contents on RVNRL film vulcanisates, with respect to the RVNRL storage time, gamma irradiation dose absorbed by the latex and the effect of different leaching time and leaching conditions. These three factors are important in the hope to determine the best possible mean of minimizing the soluble protein contents in products made from RVNRL. Within the nine months storage period employed in the study, the results show that, the longer the storage period the less the soluble protein extracted from the film samples. Gamma irradiation dose absorbed by the samples, between 5.3 kGy to 25.2 kGy seems to influence the soluble protein contents of the RVNRL films vulcanisates. The higher the dose the more was the soluble protein extracted from the film samples. At an absorbed dose of 5.3 kGy and 25.2 kGy, the soluble contents were 0. 198 mg/ml and 0.247 mg/ml respectively. At a fixed leaching temperature, the soluble proteins increases with leaching time and at a fixed leaching time, the soluble proteins increases with leaching temperature. ne highest extractable protein contents was determined at a leaching time of 10 minutes and leaching temperature of 90'C The protein analysis were done by using Modified Lowry Method

  10. Solubility Study of Curatives in Various Rubbers

    NARCIS (Netherlands)

    Guo, R.; Talma, Auke; Datta, Rabin; Dierkes, Wilma K.; Noordermeer, Jacobus W.M.

    2008-01-01

    The previous works on solubility of curatives in rubbers were mainly carried out in natural rubber. Not too much information available on dissimilar rubbers and this is important because most of the compounds today are blends of dissimilar rubbers. Although solubility can be expected to certain

  11. Solubility Products of M(II) - Carbonates

    International Nuclear Information System (INIS)

    Grauer, Rolf; Berner, Urs

    1999-01-01

    Many solubility data for M(II) carbonates commonly compiled in tables are contradictory and sometimes obviously wrong. The quality of such data has been evaluated based on the original publications and reliable solubility constants have been selected for the carbonates of Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb with the help of cross-comparisons. (author)

  12. Hansen Solubility Parameters for Octahedral Oligomeric Silsesquioxanes

    Science.gov (United States)

    2012-08-28

    1997, 80, 386-&. 5. Hansen, C. M. The three-dimensional solubility parameter -- key to paint component affinities I. J. Paint Technol. 1967, 39, 104...Chai, J.; Zhang, Q. X.; Han, D. X.; Niu, L. Synthesis and Application of Widely Soluble Graphene Sheets. Langmuir 2010, 26, 12314-12320. 12. Hansen, C

  13. A Colorful Solubility Exercise for Organic Chemistry

    Science.gov (United States)

    Shugrue, Christopher R.; Mentzen, Hans H., II; Linton, Brian R.

    2015-01-01

    A discovery chemistry laboratory has been developed for the introductory organic chemistry student to investigate the concepts of polarity, miscibility, solubility, and density. The simple procedure takes advantage of the solubility of two colored dyes in a series of solvents or solvent mixtures, and the diffusion of colors can be easily…

  14. Design for human factors (DfHF): a grounded theory for integrating human factors into production design processes.

    Science.gov (United States)

    Village, Judy; Searcy, Cory; Salustri, Filipo; Patrick Neumann, W

    2015-01-01

    The 'design for human factors' grounded theory explains 'how' human factors (HF) went from a reactive, after-injury programme in safety, to being proactively integrated into each step of the production design process. In this longitudinal case study collaboration with engineers and HF Specialists in a large electronics manufacturer, qualitative data (e.g. meetings, interviews, observations and reflections) were analysed using a grounded theory methodology. The central tenet in the theory is that when HF Specialists acclimated to the engineering process, language and tools, and strategically aligned HF to the design and business goals of the organisation, HF became a means to improve business performance. This led to engineers 'pulling' HF Specialists onto their team. HF targets were adopted into engineering tools to communicate HF concerns quantitatively, drive continuous improvement, visibly demonstrate change and lead to benchmarking. Senior management held engineers accountable for HF as a key performance indicator, thus integrating HF into the production design process. Practitioner Summary: Research and practice lack explanations about how HF can be integrated early in design of production systems. This three-year case study and the theory derived demonstrate how ergonomists changed their focus to align with design and business goals to integrate HF into the design process.

  15. In-situ atomic layer deposition growth of Hf-oxide

    International Nuclear Information System (INIS)

    Karavaev, Konstantin

    2010-01-01

    We have grown HfO 2 on Si(001) by atomic layer deposition (ALD) using HfCl 4 , TEMAHf, TDMAHf and H 2 O as precursors. The early stages of the ALD were investigated with high-resolution photoelectron spectroscopy and X-ray absorption spectroscopy. We observed the changes occurring in the Si 2p, O 1s, Hf 4f, Hf 4d, and Cl 2p (for HfCl 4 experiment) core level lines after each ALD cycle up to the complete formation of two layers of HfO 2 . The investigation was carried out in situ giving the possibility to determine the properties of the grown film after every ALD cycle or even after a half cycle. This work focused on the advantages in-situ approach in comparison with ex-situ experiments. The study provides to follow the evolution of the important properties of HfO 2 : contamination level, density and stoichiometry, and influence of the experimental parameters to the interface layer formation during ALD. Our investigation shows that in-situ XPS approach for ALD gives much more information than ex-situ experiments. (orig.)

  16. In-situ atomic layer deposition growth of Hf-oxide

    Energy Technology Data Exchange (ETDEWEB)

    Karavaev, Konstantin

    2010-06-17

    We have grown HfO{sub 2} on Si(001) by atomic layer deposition (ALD) using HfCl{sub 4}, TEMAHf, TDMAHf and H{sub 2}O as precursors. The early stages of the ALD were investigated with high-resolution photoelectron spectroscopy and X-ray absorption spectroscopy. We observed the changes occurring in the Si 2p, O 1s, Hf 4f, Hf 4d, and Cl 2p (for HfCl{sub 4} experiment) core level lines after each ALD cycle up to the complete formation of two layers of HfO{sub 2}. The investigation was carried out in situ giving the possibility to determine the properties of the grown film after every ALD cycle or even after a half cycle. This work focused on the advantages in-situ approach in comparison with ex-situ experiments. The study provides to follow the evolution of the important properties of HfO{sub 2}: contamination level, density and stoichiometry, and influence of the experimental parameters to the interface layer formation during ALD. Our investigation shows that in-situ XPS approach for ALD gives much more information than ex-situ experiments. (orig.)

  17. Effects of HfO{sub 2}/Co interface and Co/HfO{sub 2} interface on anomalous Hall behavior in perpendicular Co/Pt multilayers

    Energy Technology Data Exchange (ETDEWEB)

    Jiang, Shao-Long [Department of Materials Science and Engineering, College of Engineering, Peking University, Beijing 100871 (China); Yang, Guang [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Teng, Jiao, E-mail: tengjiao@mater.ustb.edu.cn [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Guo, Qi-Xun; Liu, Yi-Wei; Li, Xu-Jing [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China); Yu, Guang-Hua, E-mail: ghyu@mater.ustb.edu.cn [Department of Materials Physics and Chemistry, University of Science and Technology Beijing, Beijing 100083 (China)

    2017-07-01

    Highlights: • Anomalous Hall effect in perpendicular Co/Pt multilayers is studied. • Thermally stable AHE feature is obtained in [Pt/Co]{sub 3}/HfO{sub 2}/Pt multilayers. • Good thermal stability is due to enhanced intrinsic and side-jump contributions. - Abstract: Effects of the HfO{sub 2}/Co interface and the Co/HfO{sub 2} interface on thermal stability of anomalous Hall effect (AHE) in perpendicular Co/Pt multilayers have been studied. It is observed that thermally stable AHE behavior cannot be obtained in perpendicular Co/Pt multilayers with the HfO{sub 2}/Co interface, mainly due to Co-Pt interdiffusion during annealing. In contrast, thermally stable AHE feature is observed in perpendicular Co/Pt multilayers with the Co/HfO{sub 2} interface despite Co-Pt interdiffusion, which is owing to the enhancement of the side jump and intrinsic contributions to the AHE through interfacial modification after annealing.

  18. A comparative study of amorphous InGaZnO thin-film transistors with HfOxNy and HfO2 gate dielectrics

    International Nuclear Information System (INIS)

    Zou, Xiao; Tong, Xingsheng; Fang, Guojia; Yuan, Longyan; Zhao, Xingzhong

    2010-01-01

    High-κ HfO x N y and HfO 2 films are applied to amorphous InGaZnO (a-IGZO) devices as gate dielectric using radio-frequency reactive sputtering. The electrical characteristics and reliability of a-IGZO metal–insulator–semiconductor (MIS) capacitors and thin-film transistors (TFTs) are then investigated. Experimental results indicate that the nitrogen incorporation into HfO 2 can effectively improve the interface quality and enhance the reliability of the devices. Electrical properties with an interface-state density of 5.2 × 10 11 eV −1 cm −2 , capacitance equivalent thickness of 1.65 nm, gate leakage current density of 3.4 × 10 −5 A cm −2 at V fb +1 V, equivalent permittivity of 23.6 and hysteresis voltage of 110 mV are obtained for an Al/HfO x N y /a-IGZO MIS capacitor. Superior performance of HfO x N y /a-IGZO TFTs has also been achieved with a low threshold voltage of 0.33 V, a high saturation mobility of 12.1 cm 2 V −1 s −1 and a large on–off current ratio up to 7 × 10 7 (W/L = 500/20 µm) at 3 V

  19. Comparison of 14 MeV isomer production of 178m2Hf and 179m2Hf using Feshbach-Kerman-Koonin and exciton preequilibrium models

    International Nuclear Information System (INIS)

    Chadwick, M.B.; Young, P.G.

    1993-01-01

    The 178m2 Hf(16+) isomeric state has a 31-yr half life and could pose serious radioactive problems in nuclear fusion reactors if its production in 14 MeV neutron-induced reactions is significant. We present statistical/preequilibrium model calculations for the production of this isomer in the 179 Hf(n, 2n) 178m2 Hf reaction, as well as the 25-days 12.5 - isomer in the 179 Hf(n,n') 179m2 Hf reaction, using two different preequilibrium models: the exciton model and the Feshbach-Kerman-Koonin (FKK) theory. Our calculations which use the exciton model agree well with measurements, but those with the FKK theory underestimate measurements. Our calculations axe the first to probe angular momentum transfer effects in the FKK theory and suggest that, as it is presently applied, high spin-transfer reactions are underestimated. We suggest modifications to the FKK statistical averaging procedure which may result in an improved agreement with experiment

  20. Bioassay using the water soluble fraction of a Nigerian Light Crude ...

    African Journals Online (AJOL)

    Summary: A 96-hour bioassay was conducted using the water soluble fraction of a Nigerian light crude oil sample on Clarias gariepinus fingerlings. 0, 2.5, 5.0, 7.5 and 10 mls of water soluble fractions (WSF) of the oil were added to 1000 litres of de-chlorinated tap water to form 0, 25, 50 , 75 and 100 parts per million ...

  1. Hf-Nd isotope decoupling in the oceanic lithosphere: constraints from spinel peridotites from Oahu, Hawaii

    Science.gov (United States)

    Bizimis, Michael; Sen, Gautam; Salters, Vincent J. M.

    2004-01-01

    We present a detailed geochemical investigation on the Hf, Nd and Sr isotope compositions and trace and major element contents of clinopyroxene mineral separates from spinel lherzolite xenoliths from the island of Oahu, Hawaii. These peridotites are believed to represent the depleted oceanic lithosphere beneath Oahu, which is a residue of a MORB-related melting event some 80-100 Ma ago at a mid-ocean ridge. Clinopyroxenes from peridotites from the Salt Lake Crater (SLC) show a large range of Hf isotopic compositions, from ɛHf=12.2 (similar to the Honolulu volcanics series) to extremely radiogenic, ɛHf=65, at nearly constant 143Nd/ 144Nd ratios ( ɛNd=7-8). None of these samples show any isotopic evidence for interaction with Koolau-type melts. A single xenolith from the Pali vent is the only sample with Hf and Nd isotopic compositions that falls within the MORB field. The Hf isotopes correlate positively with the degree of depletion in the clinopyroxene (e.g. increasing Mg#, Cr#, decreasing Ti and heavy REE contents), but also with increasing Zr and Hf depletions relative to the adjacent REE in a compatibility diagram. The Lu/Hf isotope systematics of the SLC clinopyroxenes define apparent ages of 500 Ma or older and these compositions cannot be explained by mixing between any type of Hawaiian melts and the depleted Pacific lithosphere. Metasomatism of an ancient (e.g. 1 Ga or older) depleted peridotite protolith can, in principle, explain these apparent ages and the Nd-Hf isotope decoupling, but requires that the most depleted samples were subject to the least amount of metasomatism. Alternatively, the combined isotope, trace and major element compositions of these clinopyroxenes are best described by metasomatism of the 80-100 Ma depleted oceanic lithosphere by melts products of extensive mantle-melt interaction between Honolulu Volcanics-type melts and the depleted lithosphere.

  2. DIRECT DETERMINATION OF THE HF/H{sub 2} ABUNDANCE RATIO IN INTERSTELLAR GAS

    Energy Technology Data Exchange (ETDEWEB)

    Indriolo, Nick; Neufeld, D. A. [Department of Physics and Astronomy, Johns Hopkins University, Baltimore, MD 21218 (United States); Seifahrt, A. [Department of Astronomy and Astrophysics, University of Chicago, Chicago, IL 60637 (United States); Richter, M. J. [Department of Physics, University of California Davis, Davis, CA 95616 (United States)

    2013-02-20

    We report the first detection of the v = 1-0, R(0) ro-vibrational transition of HF at 2.499385 {mu}m arising from interstellar gas. The line is seen in absorption toward three background sources-HD 154368, Elias 29, and AFGL 2136 IRS 1-all of which have reported H{sub 2} column densities determined from observations of H{sub 2}. This allows for the first direct determination of the HF/H{sub 2} abundance ratio. We find values of N(HF)/N(H{sub 2}) = 1.15 Multiplication-Sign 10{sup -8} and 0.69 Multiplication-Sign 10{sup -8} for HD 154368 and Elias 29, respectively. The sight line toward AFGL 2136 IRS 1 also shows absorption from the v = 1-0, R(1) transition of HF, indicating warm, dense (n {sub H} {approx}> 10{sup 9} cm{sup -3}) gas, likely very close to the central protostar. Ascribing portions of the HF absorption to warm and cold gas, we find N(HF)/N(H{sub 2}) = (1.7-2.9) Multiplication-Sign 10{sup -8} and (0.33-0.58) Multiplication-Sign 10{sup -8} for the two components, respectively. Except for the warm component toward AFGL 2136 IRS 1, all observed HF/H{sub 2} ratios are well below N(HF)/N(H{sub 2}) = 3.6 Multiplication-Sign 10{sup -8}, the value predicted if nearly all gas phase fluorine is in the form of HF. Models of fluorine chemistry that account for depletion onto grains are able to reproduce the results toward HD 154368, but not in the cold, dense gas toward AFGL 2136 IRS 1 and Elias 29. Most likely, some combinations of simplifying assumptions made in the chemical models are responsible for these discrepancies.

  3. Mechanisms and selectivity for etching of HfO2 and Si in BCl3 plasmas

    International Nuclear Information System (INIS)

    Wang Chunyu; Donnelly, Vincent M.

    2008-01-01

    The authors have investigated plasma etching of HfO 2 , a high dielectric constant material, and poly-Si in BCl 3 plasmas. Etching rates were measured as a function of substrate temperature (T s ) at several source powers. Activation energies range from 0.2 to 1.0 kcal/mol for HfO 2 and from 0.8 to 1.8 kcal/mol for Si, with little or no dependence on source power (20-200 W). These low activation energies suggest that product removal is limited by chemical sputtering of the chemisorbed Hf or Si-containing layer, with a higher T s only modestly increasing the chemical sputtering rate. The slightly lower activation energy for HfO 2 results in a small improvement in selectivity over Si at low temperature. The surface layers formed on HfO 2 and Si after etching in BCl 3 plasmas were also investigated by vacuum-transfer x-ray photoelectron spectroscopy. A thin boron-containing layer was observed on partially etched HfO 2 and on poly-Si after etching through HfO 2 films. For HfO 2 , a single B(1s) feature at 194 eV was ascribed to a heavily oxidized species with bonding similar to B 2 O 3 . B(1s) features were observed for poly-Si surfaces at 187.6 eV (B bound to Si), 189.8 eV, and 193 eV (both ascribed to BO x Cl y ). In the presence of a deliberately added 0.5% air, the B-containing layer on HfO 2 is largely unaffected, while that on Si converts to a thick layer with a single B(1s) peak at 194 eV and an approximate stoichiometry of B 3 O 4 Cl

  4. 182Hf: a new stopwatch for the early solar system

    International Nuclear Information System (INIS)

    Norman, E.B.; Schramm, D.N.

    1983-01-01

    It is now well established that live 26 Al (t/sub 1/2/ = 7.2 x 10 5 yr) and 107 Pd (t/sub 1/2/ = 6.5 x 10 6 yr) were present in the early solar system. Thus, the nucleosynthetic vent (supernova) responsible for the production of these nuclei must have occurred no more than a few million years prior to the formation of solid bodies. It is possible that this event also produced the 129 I known to be present in the early solar system. However, the last event to contribute 244 Pu to the solar system occurred approx. 10 8 yr prior to the time of solidification. This latter time scale is also consistent with the lack of evidence for a 247 Cm chronometer. In this letter, we propose that 182 Hf (t/sub 1/2/ = 9 x 10 6 yr) can resolve the question of whether heavy-element non-actinide nucleosynthesis occurred during the 26 Al-producing event. The answer to this question will help to clarify the chronology of the formation of the solar system and will help to determine the astrophysical sites of heavy-element nucleosynthesis

  5. Multi-quasi-particle states in 173Hf

    International Nuclear Information System (INIS)

    Fabricius, B.; Dracoulis, G.D.; Kibedi, T.; Stuchbery, A.E.; Baxter, A.M.

    1991-01-01

    Rotational bands built on 1, 3 and 5 quasi-particle (qp) states in 173 Hf have been populated to medium and high spins through the 160 Gd( 18 O, 5n) reaction. The 1qp bands, previously identified as the 1/2 - [521], 5/2 - [512] and 7/2 + [633] (mixed i 13/2 ) Nilsson configurations, have been extended past the first back-bend and show different alignment properties, possibly originating from deformation differences. The multi-particle states were identified from excitation energies, the properties of their associated band structures and decay patterns. The 3qp states are the previously known K π =19/2 + and 23/2 - isomeric states originating from the 7/2 + [633] quasi-neutron coupled to the 6 + and 8 - , 2-quasi-proton excitations and a K π =(13/2 + ) state possibly containing the three lowest quasi-neutrons. A 5qp state with K π =(29/2 - ) was identified as the same three lowest lying quasi-neutrons coupled to the 8 - , 2-quasi-proton excitation. The low excitation energies of these two related 3- and 5-quasi-particle states implies a reduced neutron pairing gap, which can be attributed to the effect of blocking. (orig.)

  6. Multi-quasi-particles states in 173Hf

    International Nuclear Information System (INIS)

    Fabricius, B.; Dracoulis, G.D.; Kibedi, T.; Stuchbery, A.E.; Baxter, A.M.

    1990-10-01

    Rotational bands built on 1, 3 and 5 quasi-particle (qp) states in 173 Hf have been populated to medium and high spins through the 160 Gd ( 18 O,5n) reaction. The 1qp bands, previously identified as the 1/2 - [521], 5/2 - [512] and 7/2 + [633] (mixed i 1 3 /2 ) Nilsson configurations, have been extended past the first back-bend and show different alignment properties, possibly originating from deformation differences. The multi-particle states were identified from excitation energies, the properties of their associated band structures and decay patterns. The 3 qp states are the previously known K π 19/2 + and 23/2 - isomeric states originating from the 7/2 + [633] quasi-neutron coupled to the 6 + and 8 - , 2-quasi-proton excitations and a K π = (13/2 + ) state possibly containing the three lowest quasi-neutrons. A 5 qp state with K π = (29/2 - ) was identified as the same three lowest lying quasi-neutrons coupled to the 8 - , 2-quasi-proton excitation. The low excitation energies of these two related 3- and 5-quasi-particle states implies a reduced neutron pairing gap, which can be attributed to the effect of blocking. 28 refs., 2 tabs., 9 figs

  7. Three band crossings in the yrast structure of 162Hf

    International Nuclear Information System (INIS)

    Bingham, C.R.; Riedinger, L.L.; Courtney, L.H.

    1988-01-01

    The yrast sequence of 162 Hf has been observed up to a level tentatively assigned as 38 + and reveals a continuing rotational character up to that spin. Sharp backbends at rotational frequencies of 0.27 and 0.42 MeV/ℎ are attributed to isub(13/2) neutron and hsub(11/2) proton alignments, respectively. A gradual increase in the aligned angular momentum of the yrast levels between these two sharp backbends is attributed to the rotational alignment of a pair of negative parity quasineutrons (mostly hsub(9/2) in character). The interpretation of this effect is supported by the failure of the negative parity bands, which already contain this aligned hsub(9/2) neutron, to gain alignment in the same rotational frequency range. While the alignment of the hsub(9/2) quasineutrons has been predicted in the cranked shell model to occur in the rare-earth region with a large interaction strength, this represents the first clear observation of such a band crossing. (author)

  8. Indomethacin solubility estimation in 1,4-dioxane + water mixtures by the extended hildebrand solubility approach

    Directory of Open Access Journals (Sweden)

    Miller A Ruidiaz

    2011-09-01

    Full Text Available Extended Hildebrand Solubility Approach (EHSA was successfully applied to evaluate the solubility of Indomethacin in 1,4-dioxane + water mixtures at 298.15 K. An acceptable correlation-performance of EHSA was found by using a regular polynomial model in order four of the W interaction parameter vs. solubility parameter of the mixtures (overall deviation was 8.9%. Although the mean deviation obtained was similar to that obtained directly by means of an empiric regression of the experimental solubility vs. mixtures solubility parameters, the advantages of EHSA are evident because it requires physicochemical properties easily available for drugs.

  9. A Soluble, Folded Protein without Charged Amino Acid Residues

    DEFF Research Database (Denmark)

    Højgaard, Casper; Kofoed, Christian; Espersen, Roall

    2016-01-01

    side chains can maintain solubility, stability, and function. As a model, we used a cellulose-binding domain from Cellulomonas fimi, which, among proteins of more than 100 amino acids, presently is the least charged in the Protein Data Bank, with a total of only four titratable residues. We find......Charges are considered an integral part of protein structure and function, enhancing solubility and providing specificity in molecular interactions. We wished to investigate whether charged amino acids are indeed required for protein biogenesis and whether a protein completely free of titratable...... that the protein shows a surprising resilience toward extremes of pH, demonstrating stability and function (cellulose binding) in the pH range from 2 to 11. To ask whether the four charged residues present were required for these properties of this protein, we altered them to nontitratable ones. Remarkably...

  10. On the stabilization of NbV-solutions by ZrIV and HfIV

    International Nuclear Information System (INIS)

    Soerensen, E.; Bjerre, A.B.

    1987-11-01

    Niobium cannot be separated from zirconium or hafnium when these elements occur together in solution with common anions such as Cl- and SO 4 --. This is ascribed to the copolymerisation of Nb v and the hydrolyzed ionic species of Zr IV v and Hf IV by which the colloidal particles are masked as Zr- and Hf-compounds. In HCl the particles are positively charged as opposed to when they are in sulphate solution where the Zr- and Hf- sulphate complexes confer a negative charge. The two cases are considered separately. (author)

  11. Feasibility study of data transmission via HF link from a small UAV platform

    OpenAIRE

    Enander, Filip

    2017-01-01

    The High Frequency (HF) band, 3-30 MHz, is used when no infrastructure for long-range communications is available. New technology, such as digital signal processing enables higher data rate in the HF band, which in 2000s has resulted in increased commercial use. Reflection of radio waves in the ionosphere allows for beyond horizon communication, and are a unique property of the HF band. However, properties of the ionosphere are highly dependent of radiation from the sun, which varies with geo...

  12. Effective moments of inertia and spin cut off parameters in Hf isotopes

    International Nuclear Information System (INIS)

    Razavi, R.; Sharifzadeh, N.; Farahmand, M.R.

    2011-01-01

    In all statistical theories the nuclear level density is the most characteristic quantity and plays a major role in the study of nuclear structure. Most experimental data on nuclear level density have been analyzed with analytical functions of the level density. On the basis of statistical models, the effective moments of inertia and spin cut off parameters have been determined for 176 Hf, 178 Hf and 180 Hf nuclei from extensive and complete level schemes and neutron resonance densities in low excitation energy levels. Then, moments of inertia of these nuclei have been determined by nuclear rotational model. The results have been compared with their corresponding rigid body value

  13. Coulomb-nuclear interference measurements of hexadecapole deformations in 168Yb and 178,180Hf

    International Nuclear Information System (INIS)

    Nettles, W.G.; Mississippi Coll., Clinton; Ramayya, A.V.; Hamilton, J.H.

    1988-01-01

    Coulomb-nuclear interference studies of 168 Yb and 178,180 Hf have been carried out with alpha particles from the Pittsburgh tandem. From coupled channel fits to the data at 18 MeV for 168 Yb and 19.5 MeV for 178,180 Hf, β 4 c values of -0.030(20), -0.166(18), and -0.180(6) were obtained, respectively. These data agree with the positive M 04 value from sub-Coulomb studies of 168 Yb but with the large negative M 04 values from sub-Coulomb studies of 178,180 Hf. (author)

  14. Transport of the first half of the CMS hadronic forward calorimeter (HF) from building 186 (CERN Meyrin site) to the CMS construction hall at point 5, Cessy, France.

    CERN Multimedia

    Florelle Antoine

    2006-01-01

    The two halves of the Forward Hadronic Calorimeter (HF) were transported from the CERN Meyrin site to the surface assembly hall at LHC Point 5 in Cessy, France, during the first part of July. Transporting these 300 tonne objects involved the construction around them of a 65-metre long trailer, simultaneously pushed and pulled by two trucks at either end. The main road between St. Genis and Cessy was closed during these operations and a police escort was provided for the ~5 hour journeys. The two HF halves will be the first major elements to be lowered by the gantry crane into the underground experimental cavern around the end of July or beginning of August.

  15. Transport of the Hadronic Forward (HF) calorimeter from building 186 (CERN Meyrin site) to the CMS construction hall at point 5, Cessy, France.

    CERN Multimedia

    Florelle Antoine

    2006-01-01

    The two halves of the Forward Hadronic Calorimeter (HF) were transported from the CERN Meyrin site to the surface assembly hall at LHC Point 5 in Cessy, France, during the first part of July. Transporting these 300 tonne objects involved the construction around them of a 65-metre long trailer, simultaneously pushed and pulled by two trucks at either end. The main road between St. Genis and Cessy was closed during these operations and a police escort was provided for the ~5 hour journeys. The two HF halves will be the first major elements to be lowered by the gantry crane into the underground experimental cavern around the end of July or beginning of August.

  16. Salt and cocrystals of sildenafil with dicarboxylic acids: solubility and pharmacokinetic advantage of the glutarate salt.

    Science.gov (United States)

    Sanphui, Palash; Tothadi, Srinu; Ganguly, Somnath; Desiraju, Gautam R

    2013-12-02

    Sildenafil is a drug used to treat erectile dysfunction and pulmonary arterial hypertension. Because of poor aqueous solubility of the drug, the citrate salt, with improved solubility and pharmacokinetics, has been marketed. However, the citrate salt requires an hour to reach its peak plasma concentration. Thus, to improve solubility and bioavailability characteristics, cocrystals and salts of the drug have been prepared by treating aliphatic dicarboxylic acids with sildenafil; the N-methylated piperazine of the drug molecule interacts with the carboxyl group of the acid to form a heterosynthon. Salts are formed with oxalic and fumaric acid; salt monoanions are formed with succinic and glutaric acid. Sildenafil forms cocrystals with longer chain dicarboxylic acids such as adipic, pimelic, suberic, and sebacic acids. Auxiliary stabilization via C-H···O interactions is also present in these cocrystals and salts. Solubility experiments of sildenafil cocrystal/salts were carried out in 0.1N HCl aqueous medium and compared with the solubility of the citrate salt. The glutarate salt and pimelic acid cocrystal dissolve faster than the citrate salt in a two hour dissolution experiment. The glutarate salt exhibits improved solubility (3.2-fold) compared to the citrate salt in water. Solubilities of the binary salts follow an inverse correlation with their melting points, while the solubilities of the cocrystals follow solubilities of the coformer. Pharmacokinetic studies on rats showed that the glutarate salt exhibits doubled plasma AUC values in a single dose within an hour compared to the citrate salt. The high solubility of glutaric acid, in part originating from the strained conformation of the molecule and its high permeability, may be the reason for higher plasma levels of the drug.

  17. An accurate potential energy surface for the F + H2 → HF + H reaction by the coupled-cluster method

    International Nuclear Information System (INIS)

    Chen, Jun; Sun, Zhigang; Zhang, Dong H.

    2015-01-01

    A three dimensional potential energy surface for the F + H 2 → HF + H reaction has been computed by the spin unrestricted coupled cluster method with singles, doubles, triples, and perturbative quadruples [UCCSDT(2) Q ] using the augmented correlation-consistent polarised valence quadruple zeta basis set for the fluorine atom and the correlation-consistent polarised valence quadruple zeta basis set for the hydrogen atom. All the calculations are based on the restricted open-shell Hartree-Fock orbitals, together with the frozen core approximations, and the UCCSD(T)/complete basis set (CBS) correction term was included. The global potential energy surface was calculated by fitting the sampled ab initio points without any scaling factor for the correlation energy part using a neutral network function method. Extensive dynamics calculations have been carried out on the potential energy surface. The reaction rate constants, integral cross sections, product rotational states distribution, and forward and backward scattering as a function of collision energy of the F + HD → HF + D, F + HD → DF + H, and F + H 2 reaction, were calculated by the time-independent quantum dynamics scattering theory using the new surface. The satisfactory agreement with the reported experimental observations previously demonstrates the accuracy of the new potential energy surface

  18. Optical properties of a HfO2/Si stack with a trace amount of nitrogen incorporation

    Science.gov (United States)

    Ye, Li; Tingting, Jiang; Qingqing, Sun; Pengfei, Wang; Shijin, Ding; Wei, Zhang

    2012-03-01

    HfO2 films were deposited by atomic layer deposition through alternating pulsing of Hf[N(C2H5)(CH3)]4 and H2O2. A trace amount of nitrogen was incorporated into the HfO2 through ammonia annealing. The composition, the interface stability of the HfO2/Si stack and the optical properties of the annealed films were analyzed to investigate the property evolution of HfO2 during thermal treatment. With a nitrogen concentration increase from 1.41 to 7.45%, the bandgap of the films decreased from 5.82 to 4.94 eV.

  19. Serum Soluble Corin is Decreased in Stroke.

    Science.gov (United States)

    Peng, Hao; Zhu, Fangfang; Shi, Jijun; Han, Xiujie; Zhou, Dan; Liu, Yan; Zhi, Zhongwen; Zhang, Fuding; Shen, Yun; Ma, Juanjuan; Song, Yulin; Hu, Weidong

    2015-07-01

    Soluble corin was decreased in coronary heart disease. Given the connections between cardiac dysfunction and stroke, circulating corin might be a candidate marker of stroke risk. However, the association between circulating corin and stroke has not yet been studied in humans. Here, we aimed to examine the association in patients wtith stroke and community-based healthy controls. Four hundred eighty-one patients with ischemic stroke, 116 patients with hemorrhagic stroke, and 2498 healthy controls were studied. Serum soluble corin and some conventional risk factors of stroke were examined. Because circulating corin was reported to be varied between men and women, the association between serum soluble corin and stroke was evaluated in men and women, respectively. Patients with ischemic and hemorrhagic stroke had a significantly lower level of serum soluble corin than healthy controls in men and women (all P values, stroke than men in the highest quartile. Women in the lowest quartile of serum soluble corin were also more likely to have ischemic (OR, 3.10; 95% confidence interval, 1.76-5.44) and hemorrhagic (OR, 8.54; 95% confidence interval, 2.35-31.02) stroke than women in the highest quartile. ORs of ischemic and hemorrhagic stroke were significantly increased with the decreasing levels of serum soluble corin in men and women (all P values for trend, stroke compared with healthy controls. Our findings raise the possibility that serum soluble corin may have a pathogenic role in stroke. © 2015 American Heart Association, Inc.

  20. Comparing LCZ696 with enalapril according to baseline risk using the MAGGIC and EMPHASIS-HF risk scores: an analysis of mortality and morbidity in PARADIGM-HF.

    Science.gov (United States)

    Simpson, Joanne; Jhund, Pardeep S; Silva Cardoso, Jose; Martinez, Felipe; Mosterd, Arend; Ramires, Felix; Rizkala, Adel R; Senni, Michele; Squire, Iain; Gong, Jianjian; Lefkowitz, Martin P; Shi, Victor C; Desai, Akshay S; Rouleau, Jean L; Swedberg, Karl; Zile, Michael R; McMurray, John J V; Packer, Milton; Solomon, Scott D

    2015-11-10

    Although most patients in the PARADIGM-HF (Prospective Comparison of ARNI With ACEI to Determine Impact on Global Mortality and Morbidity in Heart Failure) trial had mild symptoms, there is a poor correlation between reported functional limitation and prognosis in heart failure. The aim of this study was to examine the spectrum of risk in PARADIGM-HF and the effect of LCZ696 across that spectrum. This study analyzed rates of the primary composite outcome of cardiovascular death or heart failure hospitalization, its components, and all-cause mortality using the MAGGIC (Meta-Analysis Global Group in Chronic Heart Failure) and EMPHASIS-HF (Eplerenone in Mild Patients Hospitalization and Survival Study in Heart Failure) risk scores to categorize patients. The authors determined whether risk, on the basis of these scores, modified the treatment effect of LCZ696. The complete MAGGIC risk score was available for 8,375 of the 8,399 patients in PARADIGM-HF. The median MAGGIC score was 20 (IQR: 16 to 24). An increase of 1 point was associated with a 6% increased risk for the primary endpoint (p PARADIGM-HF patients had mild symptoms, many were at high risk for adverse outcomes and obtained a large absolute benefit from LCZ696, compared with enalapril, over a relatively short treatment period. LCZ696's benefit was consistent across the spectrum of risk. (PARADIGM-HF trial [Prospective Comparison of ARNI With ACEI to Determine Impact on Global Mortality and Morbidity in Heart Failure]; NCT01035255). Copyright © 2015 American College of Cardiology Foundation. Published by Elsevier Inc. All rights reserved.

  1. Solubilities of uranium for TILA-99

    International Nuclear Information System (INIS)

    Ollila, K.; Ahonen, L.

    1998-11-01

    This report presents the evaluation of the uranium solubilities in the reference waters of TILA-99. The behaviour of uranium has been discussed separately in the near-field and far-field conditions. The bentonite/groundwater interactions have been considered in the compositions of the fresh and saline near-field reference waters. The far-field groundwaters' compositions include fresh, brackish, saline and very saline, almost brine-type compositions. The pH and redox conditions, as the main parameters affecting the solubilities, are considered. A literature study was made in order to obtain information on the recent dissolution and leaching experiments of UO 2 and spent fuel. The latest literature includes studies on UO 2 solubility under anoxic conditions, in which the methods for simulating the reducing conditions of deep groundwater have been improved. Studies on natural uraninite and its alteration products give a valuable insight into the long-term behaviour of spent fuel. Also the solubility equilibria for some relevant poorly known uranium minerals have been determined. The solubilities of the selected solubility-limiting phases were calculated using the geochemical code, EQ3/6. The NEA database for uranium was the basis for the modelling. The recently extended and updated SR '97 database was used for comparison. The solubility products for uranophane were taken from the latest literature. The recommended values for solubilities were given after a comparison between the calculated solubilities, experimental information and measured concentrations in natural groundwaters. The experiments include several UO 2 dissolution studies in synthetic groundwaters with compositions close to the reference groundwaters. (author)

  2. Solubilities of uranium for TILA-99

    Energy Technology Data Exchange (ETDEWEB)

    Ollila, K. [VTT Chemical Technology, Espoo (Finland); Ahonen, L. [Geological Survey of Finland, Espoo (Finland)

    1998-11-01

    This report presents the evaluation of the uranium solubilities in the reference waters of TILA-99. The behaviour of uranium has been discussed separately in the near-field and far-field conditions. The bentonite/groundwater interactions have been considered in the compositions of the fresh and saline near-field reference waters. The far-field groundwaters` compositions include fresh, brackish, saline and very saline, almost brine-type compositions. The pH and redox conditions, as the main parameters affecting the solubilities, are considered. A literature study was made in order to obtain information on the recent dissolution and leaching experiments of UO{sub 2} and spent fuel. The latest literature includes studies on UO{sub 2} solubility under anoxic conditions, in which the methods for simulating the reducing conditions of deep groundwater have been improved. Studies on natural uraninite and its alteration products give a valuable insight into the long-term behaviour of spent fuel. Also the solubility equilibria for some relevant poorly known uranium minerals have been determined. The solubilities of the selected solubility-limiting phases were calculated using the geochemical code, EQ3/6. The NEA database for uranium was the basis for the modelling. The recently extended and updated SR `97 database was used for comparison. The solubility products for uranophane were taken from the latest literature. The recommended values for solubilities were given after a comparison between the calculated solubilities, experimental information and measured concentrations in natural groundwaters. The experiments include several UO{sub 2} dissolution studies in synthetic groundwaters with compositions close to the reference groundwaters. (author) 81 refs.

  3. Formation of Al2O3-HfO2 Eutectic EBC Film on Silicon Carbide Substrate

    Directory of Open Access Journals (Sweden)

    Kyosuke Seya

    2015-01-01

    Full Text Available The formation mechanism of Al2O3-HfO2 eutectic structure, the preparation method, and the formation mechanism of the eutectic EBC layer on the silicon carbide substrate are summarized. Al2O3-HfO2 eutectic EBC film is prepared by optical zone melting method on the silicon carbide substrate. At high temperature, a small amount of silicon carbide decomposed into silicon and carbon. The components of Al2O3 and HfO2 in molten phase also react with the free carbon. The Al2O3 phase reacts with free carbon and vapor species of AlO phase is formed. The composition of the molten phase becomes HfO2 rich from the eutectic composition. HfO2 phase also reacts with the free carbon and HfC phase is formed on the silicon carbide substrate; then a high density intermediate layer is formed. The adhesion between the intermediate layer and the substrate is excellent by an anchor effect. When the solidification process finished before all of HfO2 phase is reduced to HfC phase, HfC-HfO2 functionally graded layer is formed on the silicon carbide substrate and the Al2O3-HfO2 eutectic structure grows from the top of the intermediate layer.

  4. Solubility limited radionuclide transport through geologic media

    International Nuclear Information System (INIS)

    Muraoka, Susumu; Iwamoto, Fumio; Pigford, T.H.

    1980-11-01

    Prior analyses for the migration of radionuclides neglect solubility limits of resolved radionuclide in geologic media. But actually some of the actinides may appear in chemical forms of very low solubility. In the present report we have proposed the migration model with no decay parents in which concentration of radionuclide is limited in concentration of solubility in ground water. In addition, the analytical solutions of the space-time-dependent concentration are presented in the case of step release, band release and exponential release. (author)

  5. Residual nilpotence and residual solubility of groups

    International Nuclear Information System (INIS)

    Mikhailov, R V

    2005-01-01

    The properties of the residual nilpotence and the residual solubility of groups are studied. The main objects under investigation are the class of residually nilpotent groups such that each central extension of these groups is also residually nilpotent and the class of residually soluble groups such that each Abelian extension of these groups is residually soluble. Various examples of groups not belonging to these classes are constructed by homological methods and methods of the theory of modules over group rings. Several applications of the theory under consideration are presented and problems concerning the residual nilpotence of one-relator groups are considered.

  6. Water Soluble Polymers for Pharmaceutical Applications

    Directory of Open Access Journals (Sweden)

    Veeran Gowda Kadajji

    2011-11-01

    Full Text Available Advances in polymer science have led to the development of novel drug delivery systems. Some polymers are obtained from natural resources and then chemically modified for various applications, while others are chemically synthesized and used. A large number of natural and synthetic polymers are available. In the present paper, only water soluble polymers are described. They have been explained in two categories (1 synthetic and (2 natural. Drug polymer conjugates, block copolymers, hydrogels and other water soluble drug polymer complexes have also been explained. The general properties and applications of different water soluble polymers in the formulation of different dosage forms, novel delivery systems and biomedical applications will be discussed.

  7. Molecular Thermodynamic Modeling of Mixed Solvent Solubility

    DEFF Research Database (Denmark)

    Ellegaard, Martin Dela; Abildskov, Jens; O’Connell, John P.

    2010-01-01

    A method based on statistical mechanical fluctuation solution theory for composition derivatives of activity coefficients is employed for estimating dilute solubilities of 11 solid pharmaceutical solutes in nearly 70 mixed aqueous and nonaqueous solvent systems. The solvent mixtures range from...... nearly ideal to strongly nonideal. The database covers a temperature range from 293 to 323 K. Comparisons with available data and other existing solubility methods show that the method successfully describes a variety of observed mixed solvent solubility behaviors using solute−solvent parameters from...

  8. LVAD patients' and surrogates' perspectives on SPIRIT-HF: An advance care planning discussion.

    Science.gov (United States)

    Metzger, Maureen; Song, Mi-Kyung; Devane-Johnson, Stephanie

    2016-01-01

    To describe LVAD patients' and surrogates' experiences with, and perspectives on SPIRIT-HF, an advance care planning (ACP) intervention. ACP is important for patients with LVAD, yet little is known about their experiences or those of their surrogates who have participated in ACP discussions. We used qualitative content analysis techniques to conduct a secondary analysis of 28 interviews with patients with LVAD (n = 14) and their surrogates (n = 14) who had participated in an RCT pilot study of SPIRIT-HF. Main themes from the data include: 1) sharing their HF stories was very beneficial; 2) participating in SPIRIT-HF led to greater peace of mind for patients and surrogates; 3) "one size does not fit all" when it comes to timing of ACP discussions. An understanding patient and surrogate perspectives may inform clinicians' approach to ACP discussions. Copyright © 2016 Elsevier Inc. All rights reserved.

  9. Reducing the stoichiometric excess of HF in the hydrofluorination of UO2

    International Nuclear Information System (INIS)

    Zhao Jun; Qiu Lufu; Zhong Xing; Xu Heqing

    1989-11-01

    In a fluidized bed, UO 2 obtained from the decomposition-reduction of AUC (Ammonium Uranyl Carbonate) was fed to absorb HF remaining in the exhaust gas of UF 4 production process. In the case of 60% conversion of UO 2 and the reaction temperature in the region of 300 deg C, HF remaining in the exhaust gas in absorbing fluidized bed was less than 7 ∼ 8% (w/w), i.e. apparent stoichiometric excess of HF had reduced to 0% more or less. Hence, with the high hydrofluorination reactivity of UO 2 obtained from the decomposition-reduction of AUC, it is possible to reduce evidently the stoichiometric excess of HF in the hydrofluorination process by two fluidized beds in series in which solids move against the gas flow

  10. Ionic exchange of Hf donor impurities in the wide-gap semiconductor Tm2O3

    International Nuclear Information System (INIS)

    Munoz, E.L.; Darriba, G.N.; Bibiloni, A.G.; Errico, L.A.; Renteria, M.

    2010-01-01

    The ionic exchange of Hf donor impurities in substitutional cationic sites of the cubic (bixbyite) phase of the wide-gap semiconductor Tm 2 O 3 was studied. The doping process was performed by ball-milling-assisted solid-state reaction of Tm 2 O 3 and neutron-activated m-HfO 2 . 181 Ta atoms, obtained by the β-decay of the 181 Hf-isotope, were used as probes in time-differential perturbed-angular-correlation (TDPAC) experiments carried out after each step of the doping process. The measured hyperfine interactions at 181 Ta sites enabled the electric-field gradient (EFG) characterization at representative Hf impurity sites of each step of the process. The efficiency and substitutional character of the exchange process is discussed and elucidated in the framework of an empirical EFG systematic established in isostructural rare-earth bixbyite sesquioxides.

  11. HF183/BFDrev and HumM2 qPCR data

    Data.gov (United States)

    U.S. Environmental Protection Agency — Concentration estimates for HF183/BFDrev and HumM2 qPCR genetic markers in raw sewage collected from 54 geographic locations across the United States. This dataset...

  12. Study of bulk Hafnium oxide (HfO2) under compression

    Science.gov (United States)

    Pathak, Santanu; Mandal, Guruprasad; Das, Parnika

    2018-04-01

    Hafnium oxide (HfO2) is a technologically important material. This material has K-value of 25 and band gap 5.8 eV. A k value of 25-30 is preferred for a gate dielectric [1]. As it shows good insulating and capacitive properties, HfO2 is being considered as a replacement to SiO2 in microelectronic devices as gate dielectrics. On the other hand because of toughening mechanism due to phase transformation induced by stress field observed in these oxides, HFO2 has been a material of investigations in various configurations for a very long time. However the controversies about phase transition of HfO2 under pressure still exists. High quality synchrotron radiation has been used to study the structural phase transition of HfO2 under pressure.

  13. Glass formation of the Fe-Hf system studied by thermodynamic calculation and ion beam mixing

    International Nuclear Information System (INIS)

    Wang, T.L.; Wang, W.C.; Li, J.H.; Liu, B.X.

    2010-01-01

    For the Fe-Hf system characterized by a negative heat of formation, the glass-forming range/ability (GFR/GFA) was studied by thermodynamic calculation based on Miedema's model and Alonso's method. It was found that amorphous phase could be formed in a composition range of 24-86 atom% Hf and that alloy with composition of Fe 58 Hf 42 has the best GFA in the system. Experimentally, ion beam mixing was carried out to synthesize amorphous alloys in the Fe-Hf system. It turned out that in the samples with overall compositions located in the calculated GFR, amorphous phases were indeed obtained, whereas no amorphous phase was obtained if the overall compositions were located outside of the predicted region favoring for amorphous alloy formation, showing a good agreement between the experimental results and the thermodynamic calculation.

  14. Conduction Mechanism and Improved Endurance in HfO2-Based RRAM with Nitridation Treatment

    Science.gov (United States)

    Yuan, Fang-Yuan; Deng, Ning; Shih, Chih-Cheng; Tseng, Yi-Ting; Chang, Ting-Chang; Chang, Kuan-Chang; Wang, Ming-Hui; Chen, Wen-Chung; Zheng, Hao-Xuan; Wu, Huaqiang; Qian, He; Sze, Simon M.

    2017-10-01

    A nitridation treatment technology with a urea/ammonia complex nitrogen source improved resistive switching property in HfO2-based resistive random access memory (RRAM). The nitridation treatment produced a high performance and reliable device which results in superior endurance (more than 109 cycles) and a self-compliance effect. Thus, the current conduction mechanism changed due to defect passivation by nitrogen atoms in the HfO2 thin film. At a high resistance state (HRS), it transferred to Schottky emission from Poole-Frenkel in HfO2-based RRAM. At low resistance state (LRS), the current conduction mechanism was space charge limited current (SCLC) after the nitridation treatment, which suggests that the nitrogen atoms form Hf-N-Ox vacancy clusters (Vo +) which limit electron movement through the switching layer.

  15. Luminescence and scintillation properties of Rb2HfCl6 crystals

    International Nuclear Information System (INIS)

    Saeki, Keiichiro; Wakai, Yuki; Fujimoto, Yutaka; Koshimizu, Masanori; Asai, Keisuke; Yanagida, Takayuki; Nakauchi, Daisuke

    2016-01-01

    We developed a scintillator based on a Rb 2 HfCl 6 crystal as a ternary halide crystal with intrinsic luminescence. In the photoluminescence spectra, two emission bands are observed at 383 and 434 nm. The 434 nm emission band for Rb 2 HfCl 6 may be attributed to [HfCl 6 ] 2- complex ion or [ZrCl 6 ] 2- impurity, since the Rb 2 HfCl 6 contained Zr as impurity at 0.62 mol %. The radioluminescence band is observed at 420 nm and can be attributed to the same origin as the photoluminescence band at 434 nm. The scintillation decay-time constants were 0.84 and 5.4 μs. The light yield was estimated to be 24,100 photons/MeV. (author)

  16. Finishing and Commissioning the New Arecibo HF Facility

    Science.gov (United States)

    Sulzer, M. P.; Gonzalez, S. A.

    2011-12-01

    The imminent completion of the major tasks in the construction of the New Arecibo HF facility means that we must verify that the components are working as intended. The antenna system and the transmitters must be separately commissioned before they can be connected together so that we an be sure it will provide 83 dbW at 8.175 MHz, and 80 dbW at 5.1 MHz. The antenna system will be ready for initial testing in September. It Illuminates the 305 meter dish using dipoles near the surface of the dish transmitting upward to a wire mesh sub-reflector. There are three crossed dipoles for each of the two frequencies. The dipoles are supported on towers mounted on concrete pads underneath the dish. Each dipole element is connected to a transmitter through a three inch coax line. The tower foundations are nearly complete, and the towers will be erected in early September, and we expect to have at least one crossed dipole in place for initial testing by the end of September. We will need to make some measurements on the antenna system to ensure that it meets our requirements. One requirement is to match the antenna impedance to the transmission line and the transmitter closely enough to meet the transmitter specifications, the closer, the better. We have additional requirements; for example, it is necessary for efficient use of the facility that the polarization be close to circular. In most experiments, we want O mode excitation. If we were to transmit linear only half the power would reach the reflection height. The symmetry of the system assures that most of the conditions for achieving accurate circular polarization are met, but one condition is not: that exciting the transmitters driving the orthogonal elements at 90 degrees assures 90 degree separation in the corresponding antenna currents. One of the dipoles of each pair points toward the center of the array. If we think of the three crossed dipoles as consisting of a reference and two that are excited relative to it

  17. Suppression of interfacial reaction for HfO2 on silicon by pre-CF4 plasma treatment

    International Nuclear Information System (INIS)

    Lai, C.S.; Wu, W.C.; Chao, T.S.; Chen, J.H.; Wang, J.C.; Tay, L.-L.; Rowell, Nelson

    2006-01-01

    In this letter, the effects of pre-CF 4 plasma treatment on Si for sputtered HfO 2 gate dielectrics are investigated. The significant fluorine was incorporated at the HfO 2 /Si substrate interface for a sample with the CF 4 plasma pretreatment. The Hf silicide was suppressed and Hf-F bonding was observed for the CF 4 plasma pretreated sample. Compared with the as-deposited sample, the effective oxide thickness was much reduced for the pre-CF 4 plasma treated sample due to the elimination of the interfacial layer between HfO 2 and Si substrate. These improved characteristics of the HfO 2 gate dielectrics can be explained in terms of the fluorine atoms blocking oxygen diffusion through the HfO 2 film into the Si substrate

  18. Effects of C and Hf concentration on phase relations and microstructure of a wrought powder-metallurgy superalloy

    Science.gov (United States)

    Miner, R. V., Jr.

    1977-01-01

    NASA IIB-11, a candidate alloy for advanced temperature turbine engine disks, and four modifications with varying C and Hf concentrations were produced from prealloyed powders. Several notable effects of C and Hf concentration in the alloys were observed. Both the amount of the gamma-prime phase and its solvus temperature increased with decreasing C, but only the gamma-prime solvus was affected by Hf, increasing with increasing Hf. Hf also promoted a cellular gamma-prime precipitation. Hf was, however, about equally distributed between gamma-prime and gamma. Hf and C both affected the carbides formed. Increasing both promoted formation of an MC relative to that of an M6C.

  19. Low modulus Ti–Nb–Hf alloy for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    González, M., E-mail: Marta.Gonzalez.Colominas@upc.edu [Department of Materials Science and Metallurgy, Universitat Politècnica de Catalunya (UPC), Avda. Diagonal 647, 08028 Barcelona (Spain); Materials Science, Elisava Escola Superior de Disseny i Enginyeria de Barcelona, La Rambla 30-32, 08002 Barcelona (Spain); Peña, J. [Department of Materials Science and Metallurgy, Universitat Politècnica de Catalunya (UPC), Avda. Diagonal 647, 08028 Barcelona (Spain); Materials Science, Elisava Escola Superior de Disseny i Enginyeria de Barcelona, La Rambla 30-32, 08002 Barcelona (Spain); Gil, F.J.; Manero, J.M. [Department of Materials Science and Metallurgy, Universitat Politècnica de Catalunya (UPC), Avda. Diagonal 647, 08028 Barcelona (Spain); Ciber-BBN (Spain)

    2014-09-01

    β-Type titanium alloys with a low elastic modulus are a potential strategy to reduce stress shielding effect and to enhance bone remodeling in implants used to substitute failed hard tissue. For biomaterial application, investigation on the mechanical behavior, the corrosion resistance and the cell response is required. The new Ti25Nb16Hf alloy was studied before and after 95% cold rolling (95% C.R.). The mechanical properties were determined by tensile testing and its corrosion behavior was analyzed by potentiostatic equipment in Hank's solution at 37 °C. The cell response was studied by means of cytotoxicity evaluation, cell adhesion and proliferation measurements. The stress–strain curves showed the lowest elastic modulus (42 GPa) in the cold worked alloy and high tensile strength, similar to that of Ti6Al4V. The new alloy exhibited better corrosion resistance in terms of open circuit potential (E{sub OCP}), but was similar in terms of corrosion current density (i{sub CORR}) compared to Ti grade II. Cytotoxicity studies revealed that the chemical composition of the alloy does not induce cytotoxic activity. Cell studies in the new alloy showed a lower adhesion and a higher proliferation compared to Ti grade II presenting, therefore, mechanical features similar to those of human cortical bone and, simultaneously, a good cell response. - Highlights: • Presents low elastic modulus and high strength and elastic deformability. • Exhibits good biocompatibility in terms of cytotoxicity and cell response. • Corrosion resistance of this alloy is good, similar to that of Ti grade II. • Potential candidate for implants used to substitute failed hard tissue.

  20. Predicting water solubility of congeners: Chloronaphthalenes-A case study

    Energy Technology Data Exchange (ETDEWEB)

    Puzyn, Tomasz, E-mail: puzi@qsar.eu.org [Faculty of Chemistry, University of Gdansk, Sobieskiego 18, 80-952 Gdansk (Poland); Mostrag, Aleksandra; Falandysz, Jerzy [Faculty of Chemistry, University of Gdansk, Sobieskiego 18, 80-952 Gdansk (Poland); Kholod, Yana; Leszczynski, Jerzy [NSF CREST Nanotoxicity Center, Department of Chemistry, Jackson State University, 1325 Lynch St, Jackson, MS 39217-0510 (United States)

    2009-10-30

    Since the important physicochemical data for chloronaphtalenes (PCNs) are still scarce, we have predicted water solubility (log S) of all 75 congeners with the Quantitative Structure-Property Relationship (QSPR) scheme. The values of log S, predicted by the most efficient model, varied from 0.01 to 1660 {mu}g dm{sup -3} (2.85 x 10{sup -11}-1.02 x 10{sup -5} mol dm{sup -3}), depending on the number of chlorine atoms present in the molecule and the substitution pattern. We found that the main factor determining relative differences in solubility between the congeners is the solvent accessible volume related to the cavitation process occurring in the solvent. The results are presented as a case study of QSPR modeling for those Persistent Organic Pollutants (POPs) that exist as families of congeners. By investigating the impact of (i) the way of the molecular descriptors' calculation, (ii) the size of applied database and (iii) chemometric method of modeling (Multiple Linear Regression, MLR, and/or Partial Least Squares regression, PLS) on the quality of the models we proposed general recommendations for dealing with congeners. We found that the combination of the B3LYP functional with 6-311++G(d,p) basis set was the most optimal technique of the molecular descriptors' calculation for congeners when comparing with semi-empirical PM3, ab initio Hartee-Fock (HF), and Moller-Pleset 2 (MP2) method carried out with different-size basis sets. Moreover, the model developed with a larger and more general database that includes chloronaphthalenes, polychlorinated dibezno-p-dioxins, furans and biphenyls predicted the values of log S for PCNs noticeable worse than the model calibrated only on PCNs. In the later case it was possible to obtain satisfactory results by employing even the simplest MLR method and only one molecular descriptor. The values of log S were also calculated with the WSKOWIN and COSMO-RS models as the reference techniques and then compared to our

  1. Predicting water solubility of congeners: Chloronaphthalenes-A case study

    International Nuclear Information System (INIS)

    Puzyn, Tomasz; Mostrag, Aleksandra; Falandysz, Jerzy; Kholod, Yana; Leszczynski, Jerzy

    2009-01-01

    Since the important physicochemical data for chloronaphtalenes (PCNs) are still scarce, we have predicted water solubility (log S) of all 75 congeners with the Quantitative Structure-Property Relationship (QSPR) scheme. The values of log S, predicted by the most efficient model, varied from 0.01 to 1660 μg dm -3 (2.85 x 10 -11 -1.02 x 10 -5 mol dm -3 ), depending on the number of chlorine atoms present in the molecule and the substitution pattern. We found that the main factor determining relative differences in solubility between the congeners is the solvent accessible volume related to the cavitation process occurring in the solvent. The results are presented as a case study of QSPR modeling for those Persistent Organic Pollutants (POPs) that exist as families of congeners. By investigating the impact of (i) the way of the molecular descriptors' calculation, (ii) the size of applied database and (iii) chemometric method of modeling (Multiple Linear Regression, MLR, and/or Partial Least Squares regression, PLS) on the quality of the models we proposed general recommendations for dealing with congeners. We found that the combination of the B3LYP functional with 6-311++G(d,p) basis set was the most optimal technique of the molecular descriptors' calculation for congeners when comparing with semi-empirical PM3, ab initio Hartee-Fock (HF), and Moller-Pleset 2 (MP2) method carried out with different-size basis sets. Moreover, the model developed with a larger and more general database that includes chloronaphthalenes, polychlorinated dibezno-p-dioxins, furans and biphenyls predicted the values of log S for PCNs noticeable worse than the model calibrated only on PCNs. In the later case it was possible to obtain satisfactory results by employing even the simplest MLR method and only one molecular descriptor. The values of log S were also calculated with the WSKOWIN and COSMO-RS models as the reference techniques and then compared to our results.

  2. Hydrogen fluoride (HF) substance flow analysis for safe and sustainable chemical industry.

    Science.gov (United States)

    Kim, Junbeum; Hwang, Yongwoo; Yoo, Mijin; Chen, Sha; Lee, Ik-Mo

    2017-11-01

    In this study, the chemical substance flow of hydrogen fluoride (hydrofluoric acid, HF) in domestic chemical industries in 2014 was analyzed in order to provide a basic material and information for the establishment of organized management system to ensure safety during HF applications. A total of 44,751 tons of HF was made by four domestic companies (in 2014); import amount was 95,984 tons in 2014 while 21,579 tons of HF was imported in 2005. The export amount of HF was 2180 tons, of which 2074 ton (China, 1422 tons, U.S. 524 tons, and Malaysia, 128 tons) was exported for the manufacturing of semiconductors. Based on the export and import amounts, it can be inferred that HF was used for manufacturing semiconductors. The industries applications of 161,123 tons of HF were as follows: manufacturing of basic inorganic chemical substance (27,937 tons), manufacturing of other chemical products such as detergents (28,208 tons), manufacturing of flat display (24,896 tons), and manufacturing of glass container package (22,002 tons). In this study, an analysis of the chemical substance flow showed that HF was mainly used in the semiconductor industry as well as glass container manufacturing. Combined with other risk management tools and approaches in the chemical industry, the chemical substance flow analysis (CSFA) can be a useful tool and method for assessment and management. The current CSFA results provide useful information for policy making in the chemical industry and national systems. Graphical abstract Hydrogen fluoride chemical substance flows in 2014 in South Korea.

  3. Extraction behavior of Nb and Ta in HF solutions with tributyl phosphate

    International Nuclear Information System (INIS)

    Murakami, M.; Tsuto, S.; Ooe, K.; Goto, S.; Kudo, H.; Haba, H.; Kanaya, J.

    2013-01-01

    Extraction behavior of carrier-free Nb and Ta with tributyl phosphate (TBP) from HF solutions was studied by a batch method. Tantalum is extracted well to an organic phase, while Nb is left in an aqueous phase at 0.053-1.0 M HF concentrations. The similar extraction trends of Nb and Ta are shown in the solid phase extraction using a TBP resin. The extraction equilibria in the solid phase extraction are attained within ∼10 s. (author)

  4. Sr-Nd-Hf isotopic fingerprinting of transatlantic dust derived from North Africa

    Science.gov (United States)

    Zhao, Wancang; Balsam, William; Williams, Earle; Long, Xiaoyong; Ji, Junfeng

    2018-03-01

    Long-range transport of African dust plays an important role in understanding dust-climate relationships including dust source areas, dust pathways and associated atmospheric and/or oceanic processes. Clay-sized Sr-Nd-Hf isotopic compositions can be used as geochemical fingerprints to constrain dust provenance and the pathways of long-range transported mineral dust. We investigated the clay-sized Sr-Nd-Hf isotopic composition of surface samples along four transects bordering the Sahara Desert. The transects are from Mali, Niger/Benin/Togo, Egypt and Morocco. Our results show that the Mali transect on the West African Craton (WAC) produces lower εNd (εNd-mean = -16.38) and εHfHf-mean = -9.59) values than the other three transects. The Egyptian transect exhibits the lowest 87Sr/86Sr ratios (87Sr/86Srmean = 0.709842), the highest εHfHf-mean = -0.34) and εNd values of the four transects. Comparison of the clay-sized Sr-Nd-Hf isotopic values from our North African samples to transatlantic African dust collected in Barbados demonstrates that the dust's provenance is primarily the western Sahel and Sahara as well as the central Sahel. Summer emission dust is derived mainly from the western Sahel and Sahara regions. The source of transatlantic dust in spring and autumn is more varied than in the summer and includes dust not only from western areas, but also south central areas. Comparison of the Sr-Nd-Hf isotopic fingerprints between the source and sink of transatlantic dust also suggests that a northwestward shift in dust source occurs from the winter, through the spring and into the summer. The isotopic data we develop here provide another tool for discriminating changes in dust archives resulting from paleoenvironmental evolution of source regions.

  5. Results of gas exposure experiments for determination of HF concentrations injurious to plants

    Energy Technology Data Exchange (ETDEWEB)

    Guderian, R

    1971-01-01

    Gas exposure experiments were performed under greenhouse conditions to determine the effects of hydrogen fluoride on the growth capacity, yield and quality of plants. Damage to plants was assessed after HF concentrations of 0.85-25 ..mu..g/m/sup 3/. The effects of definite HF quantities on plants are described and relative sensitivities of 17 deciduous trees, 9 evergreens, 24 agricultural garden plants and 17 ornamental plants are presented. 2 references, 7 tables.

  6. Thermal expansion studies on HfO2-Gd2O3 system

    International Nuclear Information System (INIS)

    Panneerselvam, G.; Antony, M.P.; Nagarajan, K.

    2014-01-01

    A series of solid solutions containing GdO 1.5 in HfO 2 , (Hf 1-y Gd y ) O 2 (y = 0.15, 0.2, 0.3, 0.41 and 0.505) were prepared by solid state method. Structural characterization and computation of lattice parameter was carried out using room temperature X-ray diffraction measurements

  7. Preparation and study of the critical-mass-free plutonium ceramics with neutron poisons Hf, Gd and Li

    International Nuclear Information System (INIS)

    Timoefeeva, L.F.; Orlov, V.K.; Malyukov, E.E.; Molomin, V.I.; Zhmak, V.A.; Semova, E.A.; Shishkov, N.V.; Nadykto, B.A.

    2002-01-01

    Powder sintering was used to produce homogeneous type oxide ceramics of Pu with Hf, Gd and Li 6 . In all the ceramics, there is the number of neutron poison (Hf, Gd and Li) atoms per plutonium atom needed, according to the physical calculation, for them to be free of critical mass. PuO 2 stabilizers high-temperature modifications of cubic HfO 2 or hexagonal Gd 2 O 3 , however, at the ratio given by the physical calculation, the plutonium is insufficient for their full stabilization. Addition of yttrium oxide as an additive stabilizing the fcc phase of HfO 2 resulted in cubic solid solution (Pu, Hf, Y)O 2-x . Pu/Li/Hf and Pu/Li/Si ceramics produced by sintering of PuO 2 and compound Li 2 HfO 3 or 6 Li 4 SiO 4 powders is characterized with presence of two phases. The method of differential thermal analysis demonstrated the phase stability of (Pu-Hf, Pu-Gd, Pu-Li-Hf) oxide ceramics in the 20-1500degC temperature range. Ceramic (Pu/Li/Si) has several endothermal effects. Tests in boiling water solutions of various composition suggest that the specimens of Pu, Hf oxides and ternary oxides (Pu, Hf, Y)O 2 are less stable in weakly acidic media than in weakly alkaline medium and distilled water. The obtained results were used as a basis to estimate the assumed solid solution region boundaries for binary Hf, Pu and ternary Hf, Pu, Y oxides on the side of HfO 2 . (author)

  8. Origin and evolution of multi-stage felsic melts in eastern Gangdese belt: Constraints from U-Pb zircon dating and Hf isotopic composition

    Science.gov (United States)

    Guo, Liang; Zhang, Hong-Fei; Harris, Nigel; Pan, Fa-Bin; Xu, Wang-Chun

    2011-11-01

    This integrated study of whole rock geochemistry, zircon U-Pb dating and Hf isotope composition for seven felsic rocks from the Nyingchi Complex in eastern Himalayan syntaxis has revealed a complex magmatic history for the eastern Gangdese belt. This involves multiple melt sources and mechanisms that uniquely identify the tectonic evolution of this part of the Himalayan orogen. Our U-Pb zircon dating reveals five stages of magmatic or anatectic events: 165, 81, 61, 50 and 25 Ma. The Jurassic granitic gneiss (165 Ma) exhibits εHf(t) values of + 1.4 to + 3.5. The late Cretaceous granite (81 Ma) shows variable εHf(t) values from - 0.9 to + 6.2, indicating a binary mixing between juvenile and old crustal materials. The Paleocene granodioritic gneiss (61 Ma) has εHf(t) values of + 5.4 to + 8.0, suggesting that it originated from partial melting of a juvenile crustal material. The Eocene anatexis is recorded in the leucosome, which has Hf isotopic composition similar to that of the Jurassic granite, indicating that the leucosome could be derived from partial melting of the Jurassic granite. The late Oligocene biotite granite (25 Ma) shows adakitic geochemical characteristics, with Sr/Y = 49.3-56.6. The presence of a large number of inherited zircons and negative εHf(t) values suggest that it sourced from anatexis of crustal materials. In contrast to the Gangdese batholiths that are mainly derived from juvenile crustal source in central Tibet, the old crustal materials play an important role for the magma generation of the felsic rocks, suggesting the existence of a crustal basement in the eastern Gangdese belt. These correspond to specific magmatic evolution stages during the convergence between India and Asia. The middle Jurassic granitic gneiss resulted from the northward subduction of the Neo-Tethyan oceanic slab. The late Cretaceous magmatism is probably related to the ocean ridge subduction. The Paleocene-Eocene magmatism, metamorphism and anatexis are

  9. Early Silurian to Early Carboniferous ridge subduction in NW Junggar: Evidence from geochronological, geochemical, and Sr-Nd-Hf isotopic data on alkali granites and adakites

    Science.gov (United States)

    Zhang, Chen; Santosh, M.; Liu, Luofu; Luo, Qun; Zhang, Xin; Liu, Dongdong

    2018-02-01

    The Central Asian Orogenic Belt (CAOB) evolved through a long-lived orogeny involving multiple episodes of subduction and accretion marking a major phase of continental growth during the Paleozoic. The northern part of the Western Junggar region (NW Junggar) offers a window into these processes, particularly to constrain the timing of closure of the Paleo-Asian Ocean. Here we report geochemical, geochronological, and isotopic data from K-feldspar granites and adakitic rocks from the NW Junggar region. Zircon U-Pb ages suggest that the granites were emplaced during Early Silurian to the Early Carboniferous (434-328 Ma). The granites show geochemical characteristics similar to those of A-type granites, with high SiO2 (71.13-76.72 wt%), Na2O + K2O (8.00-9.59 wt%), and Al2O3 (12.28-14.08 wt%), but depleted Sr, Nb, Ta and Eu. They display moderate to high positive εNd(t) and εHf(t) values (4.26-8.21 and 7.69-14.60, respectively) and young Nd and Hf model ages (T2DM-Nd = 489-740 Ma and T2DM-Hf = 471-845 Ma), suggesting magma derivation through partial melting of lower crust in the Boshchekul-Chingiz and Zharma-Saur arcs. The adakites are characterized by high Sr content (406.5-751.6 ppm), and low Y (13.8-16.4 ppm) and Yb (1.5-1.8 ppm) content, yielding relatively high Sr/Y ratios (25.38-49.41) similar to those of modern adakites. They have high positive εNd(t) and εHf(t) values (7.85-8.25 and 13.23-15.97, respectively) and young Nd and Hf model ages (T2DM-Nd = 429-535 Ma and T2DM-Hf = 355-550 Ma), indicating that their source magmas were likely derived from partial melting of the oceanic crust beneath the Boshchekul-Chingiz arc. The petrogenesis and distribution of the A-type granites and adakites, as well as the tectonic architecture of the region, suggest that a ridge subduction event might have occurred during the Early Silurian to Early Carboniferous. In combination with previous studies in the Chinese Altai, we suggest a two-sided ridge subduction model for the

  10. Atmospheric deposition of beryllium in Central Europe: comparison of soluble and insoluble fractions in rime and snow across a pollution gradient.

    Science.gov (United States)

    Bohdalkova, Leona; Novak, Martin; Voldrichova, Petra; Prechova, Eva; Veselovsky, Frantisek; Erbanova, Lucie; Krachler, Michael; Komarek, Arnost; Mikova, Jitka

    2012-11-15

    Little is known about atmospheric input of beryllium (Be) into ecosystems, despite its highly toxic behavior. For three consecutive winters (2009-2011), we measured Be concentrations in horizontal deposition (rime) and vertical deposition (snow) at 10 remote mountain-top locations in the Czech Republic, Central Europe. Beryllium was determined both in filtered waters, and in HF digests of insoluble particles. Across the sites, soluble Be concentrations in rime were 7 times higher, compared to snow (6.1 vs. 0.9ng·L(-1)). Rime scavenged the pollution-rich lower segments of clouds. The lowest Be concentrations were detected in the soluble fraction of snow. Across the sites, 34% of total Be deposition occurred in the form of soluble (bioavailable) Be, the rest were insoluble particles. Beryllium fluxes decreased in the order: vertical dry deposition insoluble>vertical dry deposition soluble>horizontal deposition soluble>vertical wet deposition insoluble>vertical wet deposition soluble>horizontal deposition insoluble. The average contributions of these Be forms to total deposition were 56, 21, 8, 7, 5 and 3%, respectively. Sites in the northeast were more Be-polluted than the rest of the country with sources of pollution in industrial Silesia. Copyright © 2012 Elsevier B.V. All rights reserved.

  11. Enhancement of organic light-emitting device performances with Hf-doped indium tin oxide anodes

    International Nuclear Information System (INIS)

    Chen, T.-H.; Liou, Y.; Wu, T.J.; Chen, J.Y.

    2004-01-01

    We have enhanced the luminance and the power efficiency of organic light-emitting devices with Hf-doped indium tin oxide (ITO) anodes instead of a CuPc layer. The Hf-doped ITO layer with a thickness of 15 nm was deposited on top of the ITO anode. Less than 10 mol. % of Hf was doped in ITO films by adjusting the sputtering rates of both sources. The highest work function of the Hf-doped ITO layers was 5.4 eV at the Hf concentrations about 10 mol. %. The driving voltages of the device have been reduced by 1 V. A luminance of 1000 cd/m 2 at 7 mA/cm 2 , a current efficiency of 14 cd/A, and a power efficiency of 6 lm/W at 6 mA/cm 2 have been achieved in the device with a 4 mol. % Hf-doped ITO layer (work function=5.2 eV). In general, the performance was about 50% better than the device with a CuPc buffer layer

  12. Comparison of HF radar measurements with Eulerian and Lagrangian surface currents

    Science.gov (United States)

    Röhrs, Johannes; Sperrevik, Ann Kristin; Christensen, Kai Håkon; Broström, Göran; Breivik, Øyvind

    2015-05-01

    High-frequency (HF) radar-derived ocean currents are compared with in situ measurements to conclude if the radar observations include effects of surface waves that are of second order in the wave amplitude. Eulerian current measurements from a high-resolution acoustic Doppler current profiler and Lagrangian measurements from surface drifters are used as references. Directional wave spectra are obtained from a combination of pressure sensor data and a wave model. Our analysis shows that the wave-induced Stokes drift is not included in the HF radar-derived currents, that is, HF radars measure the Eulerian current. A disputed nonlinear correction to the phase velocity of surface gravity waves, which may affect HF radar signals, has a magnitude of about half the Stokes drift at the surface. In our case, this contribution by nonlinear dispersion would be smaller than the accuracy of the HF radar currents, hence no conclusion can be made. Finally, the analysis confirms that the HF radar data represent an exponentially weighted vertical average where the decay scale is proportional to the wavelength of the transmitted signal.

  13. Solution Structure of Enterocin HF, an Antilisterial Bacteriocin Produced by Enterococcus faecium M3K31.

    Science.gov (United States)

    Arbulu, Sara; Lohans, Christopher T; van Belkum, Marco J; Cintas, Luis M; Herranz, Carmen; Vederas, John C; Hernández, Pablo E

    2015-12-16

    The solution structure of enterocin HF (EntHF), a class IIa bacteriocin of 43 amino acids produced by Enterococcus faecium M3K31, was evaluated by CD and NMR spectroscopy. Purified EntHF was unstructured in water, but CD analysis supports that EntHF adopts an α-helical conformation when exposed to increasing concentrations of trifluoroethanol. Furthermore, NMR spectroscopy indicates that this bacteriocin adopts an antiparallel β-sheet structure in the N-terminal region (residues 1-17), followed by a well-defined central α-helix (residues 19-30) and a more disordered C-terminal end (residues 31-43). EntHF could be structurally organized into three flexible regions that might act in a coordinated manner. This is in agreement with the absence of long-range nuclear Overhauser effect signals between the β-sheet domain and the C-terminal end of the bacteriocin. The 3D structure recorded for EntHF fits emerging facts regarding target recognition and mode of action of class IIa bacteriocins.

  14. Electric field gradients at 181Ta sites in HfOx

    International Nuclear Information System (INIS)

    Darriba, G.N.; Rodriguez, A.M.; Saitovitch, H.; Silva, P.R.J.; Pasquevich, A.F.

    2007-01-01

    In the present work we report preliminary results about the possibility to study properties of the order-disorder transition in HfO x solid solutions via the determination of the electric field gradient (EFG) at 181 Ta radioactive probes. Oxygen solution into the metal was achieved by arc melting stoichiometric amounts of metallic Hf and HfO 2 under argon atmosphere. Samples of HfO x with x=0.1 and 0.2 were prepared. Two types of samples were used for the perturbed angular correlation (PAC) experiments by doping alternatively with 181 Ta, by neutron irradiation, the metallic Hf or the hafnium oxide. The PAC results on both samples were identical, with disappearing hyperfine signals of the metal and the oxide, showing a complete diffusion of the probes independent of the way of doping. The PAC signal of the HfO x solid solution consisted in a wide distribution of EFGs due to the oxygen disorder. This scheme held even after long thermal treatments at high temperature (several days at 1273K). Annealing treatments at moderate temperature (600K) were also made. In these cases the samples were cooling at a very low rate. These results, together with those obtained by measuring samples below and above the order temperature are reported

  15. Ergonomics action research II: a framework for integrating HF into work system design.

    Science.gov (United States)

    Neumann, W P; Village, J

    2012-01-01

    This paper presents a conceptual framework that can support efforts to integrate human factors (HF) into the work system design process, where improved and cost-effective application of HF is possible. The framework advocates strategies of broad stakeholder participation, linking of performance and health goals, and process focussed change tools that can help practitioners engage in improvements to embed HF into a firm's work system design process. Recommended tools include business process mapping of the design process, implementing design criteria, using cognitive mapping to connect to managers' strategic goals, tactical use of training and adopting virtual HF (VHF) tools to support the integration effort. Consistent with organisational change research, the framework provides guidance but does not suggest a strict set of steps. This allows more adaptability for the practitioner who must navigate within a particular organisational context to secure support for embedding HF into the design process for improved operator wellbeing and system performance. There has been little scientific literature about how a practitioner might integrate HF into a company's work system design process. This paper proposes a framework for this effort by presenting a coherent conceptual framework, process tools, design tools and procedural advice that can be adapted for a target organisation.

  16. Probing the effect of neutron excess on the dynamics of Hf compound system

    Science.gov (United States)

    Sharma, Ishita; Kumar, Raj; Sharma, Manoj K.

    2018-05-01

    The reaction dynamics of 170Hf* and 174Hf* compound systems formed in 46,50Ti +124Sn reactions have been analyzed within the framework of Dynamical Cluster-decay Model (DCM) over an energy range of Ec.m.=115-156 MeV. The experimental data of fusion evaporation cross sections for 170,174Hf* systems is successfully addressed by optimizing the value of neck length ΔR. It is to be noted that calculations are performed by taking quadrupole deformations β2 with the optimum orientation of decaying fragments. Here, the effect of neutron excess has been examined on the structural properties of decaying fragments via fragmentation potential and preformation probability. The observation depicts that the isotopic effect prevails at fission region and as we move from lighter nucleus i.e. 170Hf* to heavier nucleus i.e. 174Hf*, the heavy mass fragments (HMF) start contributing along with fission fragments which are equally evident for 170Hf* as well. The ΔR values so obtained are compared at center of mass-energies which consequently provides information regarding the relative time scale of decaying fragments.

  17. Chemical states and electronic structure of a HfO(-2)/Ge(001) interface

    International Nuclear Information System (INIS)

    Seo, Kang-ill; McIntyre, Paul C.; Stanford U., Materials Sci. Dept.; Sun, Shiyu; Lee, Dong-Ick; Pianetta, Piero; SLAC, SSRL; Saraswat, Krishna C.; Stanford U., Elect. Eng. Dept.

    2005-01-01

    We report the chemical bonding structure and valence band alignment at the HfO 2 /Ge (001) interface by systematically probing various core level spectra as well as valence band spectra using soft x-rays at the Stanford Synchrotron Radiation Laboratory. We investigated the chemical bonding changes as a function of depth through the dielectric stack by taking a series of synchrotron photoemission spectra as we etched through the HfO 2 film using a dilute HF-solution. We found that a very non-stoichiometric GeO x layer exists at the HfO 2 /Ge interface. The valence band spectra near the Fermi level in each different film structure were carefully analyzed, and as a result, the valence band offset between Ge and GeO x was determined to be ΔE v (Ge-GeO x ) = 2.2 ± 0.15 eV, and that between Ge and HfO 2 , ΔE v (Ge-HfO 2 ) = 2.7 ± 0.15 eV

  18. Chemical reaction at the interface between pentacene and HfO2

    International Nuclear Information System (INIS)

    Kang, S.J.; Yi, Y.; Kim, K.H.; Yoo, C.Y.; Moewes, A.; Cho, M.H.; Denlinger, J.D.; Whang, C.N.; Chang, G.S.

    2005-01-01

    The electronic structure and the interface formation at the interface region between pentacene and HfO2 are investigated using x-ray photoelectron spectroscopy (XPS), ultraviolet photoelectron spectroscopy (UPS), and x-ray emission spectroscopy (XES). The measured C 1s XPS spectra of pentacene indicate that chemical bonding occurs at the interface between pentacene and HfO2. The carbon of pentacene reacts with oxygen belonging to HfO2 and band bending occurs at the interface due to a redistribution of charge. The determined interface dipole and band bending between pentacene and HfO2 are 0.04 and 0.1 eV, respectively. The highest occupied molecular orbital (HOMO) level is observed at 0.68 eV below the Fermi level. This chemical reaction allows us to grow a pentacene film with large grains onto HfO2. We conclude that high performance pentacene thin film transistors can be obtained by inserting an ultrathin HfO2 layer between pentacene and a gate insulator

  19. Oxidation Study of an Ultra High Temperature Ceramic Coatings Based on HfSiCN

    Science.gov (United States)

    Sacksteder, Dagny; Waters, Deborah L.; Zhu, Dongming

    2018-01-01

    High temperature fiber-reinforced ceramic matrix composites (CMCs) are important for aerospace applications because of their low density, high strength, and significantly higher-temperature capabilities compared to conventional metallic systems. The use of the SiCf/SiC and Cf/SiC CMCs allows the design of lighter-weight, more fuel efficient aircraft engines and also more advanced spacecraft airframe thermal protection systems. However, CMCs have to be protected with advanced environmental barrier coatings when they are incorporated into components for the harsh environments such as in aircraft engine or spacecraft applications. In this study, high temperature oxidation kinetics of an advanced HfSiCN coating on Cf/SiC CMC substrates were investigated at 1300 C, 1400 C, and 1500 C by using thermogravimetric analysis (TGA). The coating oxidation reaction parabolic rate constant and activation energy were estimated from the experimental results. The oxidation reaction studies showed that the coatings formed the most stable, predominant HfSiO4-HfO2 scales at 1400 C. A peroxidation test at 1400 C then followed by subsequent oxidation tests at various temperatures also showed more adherent scales and slower scale growth because of reduced the initial transient oxidation stage and increased HfSiO4-HfO2 content in the scales formed on the HfSiCN coatings.

  20. Atmospheric deposition of beryllium in Central Europe: Comparison of soluble and insoluble fractions in rime and snow across a pollution gradient

    International Nuclear Information System (INIS)

    Bohdalkova, Leona; Novak, Martin; Voldrichova, Petra; Prechova, Eva; Veselovsky, Frantisek; Erbanova, Lucie; Krachler, Michael; Komarek, Arnost; Mikova, Jitka

    2012-01-01

    Little is known about atmospheric input of beryllium (Be) into ecosystems, despite its highly toxic behavior. For three consecutive winters (2009–2011), we measured Be concentrations in horizontal deposition (rime) and vertical deposition (snow) at 10 remote mountain-top locations in the Czech Republic, Central Europe. Beryllium was determined both in filtered waters, and in HF digests of insoluble particles. Across the sites, soluble Be concentrations in rime were 7 times higher, compared to snow (6.1 vs. 0.9 ng·L −1 ). Rime scavenged the pollution-rich lower segments of clouds. The lowest Be concentrations were detected in the soluble fraction of snow. Across the sites, 34% of total Be deposition occurred in the form of soluble (bioavailable) Be, the rest were insoluble particles. Beryllium fluxes decreased in the order: vertical dry deposition insoluble > vertical dry deposition soluble > horizontal deposition soluble > vertical wet deposition insoluble > vertical wet deposition soluble > horizontal deposition insoluble. The average contributions of these Be forms to total deposition were 56, 21, 8, 7, 5 and 3%, respectively. Sites in the northeast were more Be-polluted than the rest of the country with sources of pollution in industrial Silesia. -- Highlights: ► We measured Be concentrations in rime and snow in the Czech Republic. ► Soluble Be concentrations in rime were 7 times higher than in snow. ► 34% of total Be deposition occurred in the form of soluble (bioavailable) Be. ► Dry-deposited fluxes dominated Be inputs. ► Soluble Be concentrations only rarely exceeded 30 ng·L −1 .

  1. Solubility of carbohydrates in heavy water.

    Science.gov (United States)

    Cardoso, Marcus V C; Carvalho, Larissa V C; Sabadini, Edvaldo

    2012-05-15

    The solubility of several mono-(glucose and xylose), di-(sucrose and maltose), tri-(raffinose) and cyclic (α-cyclodextrin) saccharides in H(2)O and in D(2)O were measured over a range of temperatures. The solution enthalpies for the different carbohydrates in the two solvents were determined using the vant' Hoff equation and the values in D(2)O are presented here for the first time. Our findings indicate that the replacement of H(2)O by D(2)O remarkably decreases the solubilities of the less soluble carbohydrates, such as maltose, raffinose and α-cyclodextrin. On the other hand, the more soluble saccharides, glucose, xylose, and sucrose, are practically insensitive to the H/D replacement in water. Copyright © 2012 Elsevier Ltd. All rights reserved.

  2. Enhancement of Solubility and Bioavailability of Candesartan ...

    African Journals Online (AJOL)

    Purpose: To enhance the otherwise poor solubility and bioavailability of candesartan cilexetil (CDS). Methods: This ... PEG 6000-based solid dispersions showed 1st order drug release kinetics. ..... the liver due to quercetin's inhibitory effect on.

  3. An Introduction to the Understanding of Solubility.

    Science.gov (United States)

    Letcher, Trevor M.; Battino, Rubin

    2001-01-01

    Explores different solubility processes and related issues, including the second law of thermodynamics and ideal mixtures, real liquids, intermolecular forces, and solids in liquids or gases in liquids. (Contains 22 references.) (ASK)

  4. Progress in the research of neptunium solubility

    International Nuclear Information System (INIS)

    Jiang Tao; Liu Yongye; Yao Jun

    2012-01-01

    237 Np is considered a possible long-term potential threat for environment, because of its long half-life, high toxicity and its mobile nature under aerobic conditions due to the high chemical stability of its pentavalent state. Therefore 237 Np is considered as one of high-level radioactive waste and need to be disposed in deep geologic disposal repository. The dissolution behavior is an important aspect of migration research. The solubility is considered very important for high level waste geological disposal safety and environmental evaluation. The solubility determines the maximum concentration of the discharge, and then it is initial concentration of the radionuclides migration to the environment. The solubility impact directly on radionuclides migration in host rock, and can be used to predict the concentration and speciation of radionuclides in groundwater around disposal sites many years later. This paper focused on research results of the solubility, some proposals for Np dissolution chemistry research were also been suggested. (authors)

  5. Solubility Products of M(II) - Carbonates

    Energy Technology Data Exchange (ETDEWEB)

    Grauer, Rolf; Berner, Urs [ed.

    1999-01-01

    Many solubility data for M(II) carbonates commonly compiled in tables are contradictory and sometimes obviously wrong. The quality of such data has been evaluated based on the original publications and reliable solubility constants have been selected for the carbonates of Mn, Fe, Co, Ni, Cu, Zn, Cd and Pb with the help of cross-comparisons. (author) translated from a PSI internal report written in German in 1994 (TM-44-94-05). 5 figs., 1 tab., 68 refs.

  6. Hydrogen solubility in polycrystalline - and nonocrystalline niobium

    International Nuclear Information System (INIS)

    Ishikawa, T.T.; Silva, J.R.G. da

    1981-01-01

    Hydrogen solubility in polycrystalline and monocrystalline niobium was measured in the range 400 0 C to 1000 0 C at one atmosphere hydrogen partial pressure. The experimental technique consists of saturation of the solvent metal with hydrogen, followed by quenching and analysis of the solid solution. It is presented solubility curves versus reciprocal of the absolute doping temperature, associated with their thermodynamical equation. (Author) [pt

  7. Respiratory carcinogenicity assessment of soluble nickel compounds.

    OpenAIRE

    Oller, Adriana R

    2002-01-01

    The many chemical forms of nickel differ in physicochemical properties and biological effects. Health assessments for each main category of nickel species are needed. The carcinogenicity assessment of water-soluble nickel compounds has proven particularly difficult. Epidemiologic evidence indicates an association between inhalation exposures to nickel refinery dust containing soluble nickel compounds and increased risk of respiratory cancers. However, the nature of this association is unclear...

  8. Correlation of Helium Solubility in Liquid Nitrogen

    Science.gov (United States)

    VanDresar, Neil T.; Zimmerli, Gregory A.

    2012-01-01

    A correlation has been developed for the equilibrium mole fraction of soluble gaseous helium in liquid nitrogen as a function of temperature and pressure. Experimental solubility data was compiled and provided by National Institute of Standards and Technology (NIST). Data from six sources was used to develop a correlation within the range of 0.5 to 9.9 MPa and 72.0 to 119.6 K. The relative standard deviation of the correlation is 6.9 percent.

  9. Hydrothermal solubility of uraninite. Final technical report

    International Nuclear Information System (INIS)

    Parks, G.A.; Pohl, D.C.

    1985-01-01

    Experimental measurements of the solubility of UO 2 from 100 to 300 0 C under 500 bars H 2 , in NaCl solutions at pH from 1 to 8 do not agree with solubilities calculated using existing thermodynamic databases. For pH 2 (hyd) has precipitated and is controlling solubility. For pH > 8, solubilities at all temperatures are much lower than predicted, suggesting that the U(OH)/sub delta/ - complex is much weaker than predicted. Extrapolated to 25 0 C, high pH solubility agrees within experimental error with the upper limit suggested by Ryan and Rai (1983). In the pH range 2 to 6, solubilities are up to three orders of magnitude lower than predicted for temperatures exceeding 200 0 C and up to two orders higher than predicted at lower temperatures. pH dependence in this region is negligible suggesting that U(OH) 4 (aq) predominates, thus the stability of this species is higher than presently estimated at low temperatures, but the enthalpy of solution is smaller. A low maximum observed near pH approx. =3 is presently unexplained. 40 refs., 16 figs., 12 tabs

  10. Uranium solubility and speciation in ground water

    International Nuclear Information System (INIS)

    Ollila, K.

    1985-04-01

    The purpose of this study has been to assess the solubility and possible species of uranium in groundwater at the disposal conditions of spent fuel. The effects of radiolysis and bentonite are considered. The assessment is based on the theoretical calculations found in the literature. The Finnish experimental results are included. The conservative estimate for uranium solubility under the oxidizing conditions caused by alpha radiolysis is based on the oxidation of uranium to the U(VI) state and formation of carbonate complex. For the groundwater with the typical carbonate content of 275 mg/l and the high carbonate content of 485 mg/l due to bentonite, the solubility values of 360 mg u/l and 950 mg U/l, are obtained, respectively. The experimental results predict considerably lower values, 0.5-20 mg U/l. The solubility of uranium under the undisturbed reducing conditions may be calculated based on the hydrolysis, carbonate complexation and redox reactions. The results vary considerably depending on the thermodynamic data used. The wide ranges of the most important groundwater parameters are seen in the solubility values. The experimental results show the same trends. As a conservative value for the solubility in reducing groundwater 50-500 μg U/l is estimated. (author)

  11. Sibutramine characterization and solubility, a theoretical study

    Science.gov (United States)

    Aceves-Hernández, Juan M.; Nicolás Vázquez, Inés; Hinojosa-Torres, Jaime; Penieres Carrillo, Guillermo; Arroyo Razo, Gabriel; Miranda Ruvalcaba, René

    2013-04-01

    Solubility data from sibutramine (SBA) in a family of alcohols were obtained at different temperatures. Sibutramine was characterized by using thermal analysis and X-ray diffraction technique. Solubility data were obtained by the saturation method. The van't Hoff equation was used to obtain the theoretical solubility values and the ideal solvent activity coefficient. No polymorphic phenomena were found from the X-ray diffraction analysis, even though this compound is a racemic mixture of (+) and (-) enantiomers. Theoretical calculations showed that the polarisable continuum model was able to reproduce the solubility and stability of sibutramine molecule in gas phase, water and a family of alcohols at B3LYP/6-311++G (d,p) level of theory. Dielectric constant, dipolar moment and solubility in water values as physical parameters were used in those theoretical calculations for explaining that behavior. Experimental and theoretical results were compared and good agreement was obtained. Sibutramine solubility increased from methanol to 1-octanol in theoretical and experimental results.

  12. Zircon and baddeleyite from the economic ultramafic-mafic Noril'sk-1 intrusion (Russia): Hf-isotope constraints on source composition

    Science.gov (United States)

    Malitch, K. N.; Belousova, E. A.; Badanina, I. Yu.; Griffin, W. L.

    2012-04-01

    of the Noril'sk-1 intrusion, which served as the favorable factor for accumulation of ores of unique scales and concentrations, To test this hypothesis, in situ Hf-isotope data were collected on the dated spots within single zircon grains. The analysis used a New Wave LUV213 laser-ablation microprobe attached to a Nu plasma MC-ICP-MS at GEMOC (Griffin et al. 2002). Hf-isotope results grouped on the basis of lithology show notable differences. Zircons from the unmineralized 'layered rock sequence' (e.g., olivine-free gabbro, olivine-bearing gabbro and olivine gabbro) are characterized by the most 'radiogenic' initial 176Hf/177Hf and some of ɛHf values close to those of the Depleted Mantle. Irrespective of zircon population most radiogenic Hf-isotope compositions are typical for olivine-free gabbro (mean ɛHf 7.3 ± 1.1 for sample N1-4), olivine-bearing gabbro (9.2 ± 3.8, sample N1-5) and olivine gabbro (8.3 ± 2.0, sample N1-6). In contrast, zircons from the leucogabbro that encloses the low-sulphide horizon (N1-3), and plagiowehrlite (N1-7) and taxitic-textured rocks (N1-8 and N1-9) with disseminated sulphide ores have less radiogenic Hf-isotope values (e.g., mean ɛHf6.2 ± 1.4, 5.9 ± 2.3, 6.4 ± 1.2 and 4.9±1.4, respectively). The least radiogenic values (ɛHffrom -2.9 to +2.3, mean ɛHf = 0.1 ± 1.9) are recorded in gabbro-diorite from the upper part of intrusion. The baddeleyite from olivine-free gabbro has the narrowest range of ɛHf values (e.g. 6.8-8.4), with a mean of ɛHfof 7.6 ± 0.8, closely matching that of zircon (mean ɛHf= 7.3 ± 1.1). Zircons from the leucogabbro that hosts the low-sulphide horizon (N1-3), and ultramafic and taxitic-textured lithologies with disseminated sulphide ores (N1-7, N1-8 and N1-9) have less radiogenic ɛHf values than those in barren lithologies. The Hf-isotope data for zircons from ore-bearing rocks thus suggest that the Noril'sk magmas represent mixing between a juvenile source equivalent to the Depleted Mantle and a

  13. Lattice Thermal Conductivity of Ultra High Temperature Ceramics (UHTC) ZrB2 and HfB2 from Atomistic Simulations

    Science.gov (United States)

    Lawson, John W.; Daw, Murray S.; Bauschlicher, Charles W.

    2012-01-01

    Ultra high temperature ceramics (UHTC) including ZrB2 and HfB2 have a number of properties that make them attractive for applications in extreme environments. One such property is their high thermal conductivity. Computational modeling of these materials will facilitate understanding of fundamental mechanisms, elucidate structure-property relationships, and ultimately accelerate the materials design cycle. Progress in computational modeling of UHTCs however has been limited in part due to the absence of suitable interatomic potentials. Recently, we developed Tersoff style parameterizations of such potentials for both ZrB2 and HfB2 appropriate for atomistic simulations. As an application, Green-Kubo molecular dynamics simulations were performed to evaluate the lattice thermal conductivity for single crystals of ZrB2 and HfB2. The atomic mass difference in these binary compounds leads to oscillations in the time correlation function of the heat current, in contrast to the more typical monotonic decay seen in monoatomic materials such as Silicon, for example. Results at room temperature and at elevated temperatures will be reported.

  14. Solubility measurement of uranium in uranium-contaminated soils

    International Nuclear Information System (INIS)

    Lee, S.Y.; Elless, M.; Hoffman, F.

    1993-08-01

    A short-term equilibration study involving two uranium-contaminated soils at the Fernald site was conducted as part of the In Situ Remediation Integrated Program. The goal of this study is to predict the behavior of uranium during on-site remediation of these soils. Geochemical modeling was performed on the aqueous species dissolved from these soils following the equilibration study to predict the on-site uranium leaching and transport processes. The soluble levels of total uranium, calcium, magnesium, and carbonate increased continually for the first four weeks. After the first four weeks, these components either reached a steady-state equilibrium or continued linearity throughout the study. Aluminum, potassium, and iron, reached a steady-state concentration within three days. Silica levels approximated the predicted solubility of quartz throughout the study. A much higher level of dissolved uranium was observed in the soil contaminated from spillage of uranium-laden solvents and process effluents than in the soil contaminated from settling of airborne uranium particles ejected from the nearby incinerator. The high levels observed for soluble calcium, magnesium, and bicarbonate are probably the result of magnesium and/or calcium carbonate minerals dissolving in these soils. Geochemical modeling confirms that the uranyl-carbonate complexes are the most stable and dominant in these solutions. The use of carbonate minerals on these soils for erosion control and road construction activities contributes to the leaching of uranium from contaminated soil particles. Dissolved carbonates promote uranium solubility, forming highly mobile anionic species. Mobile uranium species are contaminating the groundwater underlying these soils. The development of a site-specific remediation technology is urgently needed for the FEMP site

  15. Dual HF radar study of the subauroral polarization stream

    Directory of Open Access Journals (Sweden)

    R. A. Makarevich

    2008-01-01

    Full Text Available The dual HF radars comprising the Tasman International Geophysical Environment Radar (TIGER system often observe localized high-velocity F-region plasma flows (≥1500 m/s in the midnight sector (20:00–02:00 MLT at magnetic latitudes as low as Λ=60° S. The flow channels exhibit large variability in the latitudinal extent and electric field strength, and are similar to the subauroral polarization stream or SAPS, a plasma convection feature thought to be related to the polarization electric field due to the charge separation during substorm and storm development. In this study, the 2-D plasma drift velocity within the channel is derived for each of the two TIGER radars from the maximum velocities measured in all 16 radar beams within the latitudinally narrow channel, and the time variation of the subauroral electric field is examined near substorm onset. It is demonstrated that the flow channel often does not have a clear onset, rather it manifests differently in different phases of its evolution and can persist for at least two substorm cycles. During the growth phase the electric fields within the flow channel are difficult to distinguish from those of the background auroral convection but they start to increase near substorm onset and peak during the recovery phase, in contrast to what has been reported previously for auroral convection which peaks just before the substorm onset and falls sharply at the substorm onset. The response times to substorm onset range from −5 to +40 min and show some dependence on the substorm location with longer delays observed for substorms eastward of the radars' viewing area. The propagation velocity of the high-velocity region is also investigated by comparing the observations from the two closely-spaced TIGER radars. The observations are consistent with the notion that the polarization electric field is established with the energetic ions drifting westward and equatorward from the initial substorm

  16. Cosmic-ray production of tungsten isotopes in lunar samples and meteorites and its implications for Hf-W cosmochemistry

    Science.gov (United States)

    Leya, Ingo; Wieler, Rainer; Halliday, Alex N.

    2000-01-01

    Excesses and deficiencies in 182W in meteorites and lunar samples relative to the terrestrial 182W atomic abundance have been assigned to the decay of 182Hf (t1/2=9 Ma) and have been used to date metal-silicate fractionation events in the early solar system. Because the effects are very small, production and burn-out of tungsten isotopes by cosmic ray interactions are a concern in such studies. Masarik [J. Masarik, Contribution of neutron-capture reactions to observed tungsten isotopic ratios, Earth Planet. Sci. Lett. 152 (1997) 181-185] showed that neutron-capture reactions on tungsten isotopes can account at best for a minor part of the observed deficit of 182W in Toluca and other iron meteorites. On the other hand, in lunar samples and stony meteorites the production of 182W from 181Ta may become crucial. Here, we calculate this contribution as well as production and consumption of 182-186W by other neutron-induced reactions. The neutron fluence of each sample is estimated by its nominal cosmic-ray exposure age deduced from noble gas data. This approach overestimates the true cosmogenic W isotopic shifts for samples that might have been irradiated very close to the regolith surface. A quantitative estimate is often also hampered by a lack of Ta data. Despite these reservations, it appears that in many lunar samples neutron-capture on Ta has caused a large part of the observed 182W excess. On the other hand, in some samples, especially those with very low exposure ages, clearly only a minor or even negligible fraction of the 182W excess can be cosmogenic. Therefore, the conclusion, based on Hf-W model ages, that the Moon formed 50 Myr after the start of the solar system remains valid. Martian meteorites have lower Ta/W ratios and cosmic ray exposure ages than most lunar samples. Therefore, cosmogenic production has not significantly altered the W isotopic composition in Martian meteorites. Observed 182W excesses in Martian meteorites as well as the very large

  17. Collapse of the magnetic moment under pressure of AFe{sub 2} (A=Y, Zr, Lu and Hf) in the cubic Laves phase

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Wenxu, E-mail: xwzhang@uestc.edu.cn; Zhang, Wanli

    2016-04-15

    The electronic structures of four Laves phase iron compounds (e.g. YFe{sub 2}, ZrFe{sub 2}, LuFe{sub 2} and HfFe{sub 2}) have been calculated with a state-of-the-art full potential electronic structure code. Our theoretical work predicted that the magnetic moments collapse under hydrostatic pressure. This feature is found to be universal in these materials. Its electronic origin is provided by the sharp peaks in the density of states near the Fermi level. It is shown that a first order quantum phase transition can be expected under pressure in Y(Zr, or Lu)Fe{sub 2}, while a second order one in HfFe{sub 2}. The bonding characteristics are discussed to elucidate the equilibrium lattice constant variation. The large spontaneous volume magnetostriction gives one of the most important characteristics of these compounds. Invar anomalies in these compounds can be partly explained by the current work when the fast continuous magnetic moment decrease with the decrease of the lattice constant was properly considered. This work may be as a first insight into the rich world of quantum phase transition and Invar mechanism in these Laves phase compounds. - Highlights: • Magnetic moment of YFe{sub 2}, ZrFe{sub 2}, LuFe{sub 2} and HfFe{sub 2} collapses under pressure. • The transition in Y(Zr or Lu) Fe{sub 2} under pressure is first order. • The transition in HfFe{sub 2} under pressure is second order. • The Invar effects in the compounds can be put into the magnetostriction model.

  18. Binary systems solubilities of inorganic and organic compounds, v.1 pt.2

    CERN Document Server

    Stephen, H

    2013-01-01

    Solubilities of Inorganic and Organic Compounds, Volume 1: Binary Systems, Part 1 is part of an approximately 5,500-page manual containing a selection from the International Chemical Literature on the Solubilities of Elements, Inorganic Compounds, Metallo-organic and Organic Compounds in Binary, Ternary and Multi-component Systems. A careful survey of the literature in all languages by a panel of scientists specially appointed for the task by the U.S.S.R. Academy of Sciences, Moscow, has made the compilation of this work possible. The complete English edition in five separately bound volumes w

  19. Lu{sub 2}O{sub 3}:Tb,Hf storage phosphor

    Energy Technology Data Exchange (ETDEWEB)

    Kulesza, Dagmara; Trojan-Piegza, Joanna [Faculty of Chemistry, University of Wroclaw, 14 F. Joliot-Curie Street, 50-383 Wroclaw (Poland); Zych, Eugeniusz, E-mail: zych@wchuwr.p [Faculty of Chemistry, University of Wroclaw, 14 F. Joliot-Curie Street, 50-383 Wroclaw (Poland)

    2010-03-15

    Lu{sub 2}O{sub 3}:Tb,Hf ceramics containing 0.1% of Tb and 0-1.5% of Hf were prepared in reducing atmosphere at 1700 {sup o}C and their thermoluminescence properties were systematically studied. For comparison Tb,Ca co-doped specimen was also fabricated and investigated. The Tb,Hf ceramics shows basically a single TL band located around 180 {sup o}C as found with heating rate of 15 {sup o}C/min. Ceramics singly doped with Tb show complex TL glow curves indicating the presence of traps of very different depths. On the other hand Tb,Ca co-doping is beneficial for the development of shallow traps with the main TL band around 70 {sup o}C. Hence, the aliovalent impurities, Ca{sup 2+} and Hf{sup 4+}, strongly influenced the traps structure in Lu{sub 2}O{sub 3}:Tb ceramics, each of them in its own specific way. Isothermal decay of Lu{sub 2}O{sub 3}:Tb,Hf at 185 {sup o}C was recorded and its shape suggest that multiple hole trapping occurs in the Lu{sub 2}O{sub 3}:Tb,Hf ceramics. Due to the different traps depths the Lu{sub 2}O{sub 3}:Tb,Hf ceramics possess properties typical for storage phosphors, while Lu{sub 2}O{sub 3}:Tb,Ca is a persistent luminescent material rather.

  20. Structural, morphological, optical and photoluminescence properties of HfO2 thin films

    International Nuclear Information System (INIS)

    Ma, C.Y.; Wang, W.J.; Wang, J.; Miao, C.Y.; Li, S.L.; Zhang, Q.Y.

    2013-01-01

    Nanocrystalline monoclinic HfO 2 films with an average crystal size of 4.2–14.8 nm were sputter deposited under controlled temperatures and their structural characteristics and optical and photoluminescence properties have been evaluated. Structural investigations indicate that monoclinic HfO 2 films grown at higher temperatures above 400 °C are highly oriented along the (− 111) direction. The lattice expansion increases with diminishing HfO 2 crystalline size below 6.8 nm while maximum lattice expansion occurs with highly oriented monoclinic HfO 2 of crystalline size about 14.8 nm. The analysis of atomic force microscopy shows that the film growth at 600 °C can be attributed to the surface-diffusion-dominated growth. The intensity of the shoulderlike band that initiates at ∼ 5.7 eV and saturates at 5.94 eV shows continued increase with increasing crystalline size, which is intrinsic to nanocrystalline monoclinic HfO 2 films. Optical band gap varies in the range 5.40 ± 0.03–5.60 ± 0.03 eV and is slightly decreased with the increase in crystalline size. The luminescence band at 4.0 eV of HfO 2 films grown at room temperature can be ascribed to the vibronic transition of excited OH · radical while the emission at 3.2–3.3 eV for the films grown at all temperatures was attributed to the radiative recombination at impurity and/or defect centers. - Highlights: • Nanocrystalline monoclinic HfO 2 films were sputter deposited. • Structural, optical and photoluminescence properties were studied. • To analyze the scaling behavior using the power spectral density • Optical and photoluminescence properties strongly depend on film growth temperature

  1. Determination of calcium salt solubility with changes in pH and P(CO(2)), simulating varying gastrointestinal environments.

    Science.gov (United States)

    Goss, Sandra L; Lemons, Karen A; Kerstetter, Jane E; Bogner, Robin H

    2007-11-01

    The amount of calcium available for absorption is dependent, in part, on its sustained solubility in the gastrointestinal (GI) tract. Many calcium salts, which are the calcium sources in supplements and food, have pH-dependent solubility and may have limited availability in the small intestine, the major site of absorption. The equilibrium solubility of four calcium salts (calcium oxalate hydrate, calcium citrate tetrahydrate, calcium phosphate, calcium glycerophosphate) were determined at controlled pH values (7.5, 6.0, 4.5 and solubility of calcium carbonate was also measured at pH 7.5, 6.0 and 4.5 with two CO(2) environments (0.3 and 152 mmHg) above the solution. The precipitation profile of CaCO(3) was calculated using in-vivo data for bicarbonate and pH from literature and equilibrium calculations. As pH increased, the solubility of each calcium salt increased. However, in distilled water each salt produced a different pH, affecting its solubility value. Although calcium citrate does have a higher solubility than CaCO(3) in water, there is little difference when the pH is controlled at pH 7.5. The partial pressure of CO(2) also played a role in calcium carbonate solubility, depressing the solubility at pH 7.5. The calculations of soluble calcium resulted in profiles of available calcium, which agreed with previously published in-vivo data on absorbed calcium. The experimental data illustrate the impact of pH and CO(2) on the solubility of many calcium salts in the presence of bicarbonate secretions in the intestine. Calculated profiles using in-vivo calcium and bicarbonate concentrations demonstrate that large calcium doses may not further increase intestinal calcium absorption once the calcium carbonate solubility product has been reached.

  2. Solubility study of Tc(IV) oxides

    International Nuclear Information System (INIS)

    Liu, D.J.; Fan, X.H.

    2005-01-01

    The deep geological disposal of the high level radioactive wastes is expected to be a safer disposal method in most countries. The long-lived fission product 99 Tc is present in large quantities in nuclear wastes and its chemical behavior in aqueous solution is of considerable interest. Under oxidizing conditions technetium exists as the anionic species TcO 4 - whereas under the reducing conditions, expected to exist in a deep geological repository, it is generally predicted that technetium will be present as TcO 2 ·nH 2 O. Hence, the mobility of Tc(IV) in reducing groundwater may be limited by the solubility of TcO 2 ·nH 2 O under these conditions. Due to this fact it is important to investigate the solubility of TcO 2 ·nH 2 O. The solubility determines the release of radionuclides from waste form and is used as a source term in radionuclide migration analysis in performance assessment of radioactive waste repository. Technetium oxide was prepared by reduction of a technetate solution with Sn 2 + . The solubility of Tc(IV) oxide has been determined in simulated groundwater and redistilled water under aerobic and anaerobic conditions. The effects of pH and CO 3 2- concentration of solution on solubility of Tc(IV) oxide were studied. The concentration of total technetium and Tc(IV) species in the solutions were periodically determined by separating the oxidized and reduced technetium species using a solvent extraction procedure and counting the beta activity of the 99 Tc with a liquid scintillation counter. The experimental results show that the rate of oxidation of Tc(IV) in simulated groundwater and redistilled water is about (1.49-1.86) x 10 -9 mol/(L·d) under aerobic conditions, but Tc(IV) in simulated groundwater and redistilled water is not oxidized under anaerobic conditions. Under aerobic or anaerobic conditions the solubility of Tc(IV) oxide in simulated groundwater and redistilled water is equal on the whole after centrifugation or ultrafiltration. The

  3. Influence of milling process on efavirenz solubility

    Directory of Open Access Journals (Sweden)

    Erizal Zaini

    2017-01-01

    Full Text Available Introduction: The aim of this study was to investigate the influence of the milling process on the solubility of efavirenz. Materials and Methods: Milling process was done using Nanomilling for 30, 60, and 180 min. Intact and milled efavirenz were characterized by powder X-ray diffraction, scanning electron microscopy (SEM, spectroscopy infrared (IR, differential scanning calorimetry (DSC, and solubility test. Results: The X-ray diffractogram showed a decline on peak intensity of milled efavirenz compared to intact efavirenz. The SEM graph depicted the change from crystalline to amorphous habit after milling process. The IR spectrum showed there was no difference between intact and milled efavirenz. Thermal analysis which performed by DSC showed a reduction on endothermic peak after milling process which related to decreasing of crystallinity. Solubility test of intact and milled efavirenz was conducted in distilled water free CO2with 0.25% sodium lauryl sulfate media and measured using high-performance liquid chromatography method with acetonitrile: distilled water (80:20 as mobile phases. The solubility was significantly increased (P < 0.05 after milling processes, which the intact efavirenz was 27.12 ± 2.05, while the milled efavirenz for 30, 60, and 180 min were 75.53 ± 1.59, 82.34 ± 1.23, and 104.75 ± 0.96 μg/mL, respectively. Conclusions: Based on the results, the solubility of efavirenz improved after milling process.

  4. Solubility of lithium deuteride in liquid lithium

    International Nuclear Information System (INIS)

    Veleckis, E.; Yonco, R.M.; Maroni, V.A.

    1977-01-01

    The solubility of LiD in liquid lithium between the eutectic and monotectic temperatures was measured using a direct sampling method. Solubilities were found to range from 0.0154 mol.% LiD at 199 0 C to 3.32 mol.% LiD at 498 0 C. The data were used in the derivation of an expression for the activity coefficient of LiD as a function of temperature and composition and an equation relating deuteride solubility and temperature, thus defining the liquidus curve. Similar equations were also derived for the Li-LiH system using the existing solubility data. Extrapolation of the liquidus curves yielded the eutectic concentrations (0.040 mol.% LiH and 0.035 mol.% LiD) and the freezing point depressions (0.23 0 C for Li-LiH and 0.20 0 C for Li-LiD) at the eutectic point. The results are compared with the literature data for hydrogen and deuterium. The implications of the relatively high solubility of hydrogen isotopes in lithium just above the melting point are discussed with respect to the cold trapping of tritium in fusion reactor blankets. (Auth.)

  5. Solubility studies of Np(IV)

    International Nuclear Information System (INIS)

    Zhang Yingjie; Yao Jun; Jiao Haiyang; Ren Lihong; Zhou Duo; Fan Xianhua

    2001-01-01

    The solubility of Np(IV) in simulated underground water and redistilled water has been measured with the variations of pH(6-12) and storage time (0-100 d) in the presence of reductant (Na 2 S 2 O 4 , metallic Fe). All experiments are performed in a low oxygen concentration glove box containing high purity Ar(99.99%), with an oxygen content of less than 5 x 10 -6 mol/mol. Experimental results show that the variation of pH in solution has little effect on the solubility of Np(IV) in the two kinds of water; the measured solubility of Np(IV) is affected by the composition of solution; with Na 2 S 2 O 4 as a reductant, the solubility of Np(IV) in simulated underground water is (9.23 +- 0.48) x 10 -10 mol/L, and that in redistilled water is (8.31 +- 0.35) x 10 -10 mol/L; with metallic Fe as a reductant, the solubility of Np(IV) in simulated underground water is (1.85 +- 0.56) x 10 -9 mol/L, and that in redistilled water is (1.48 +- 0.66) x 10 -9 mol/L

  6. Solubility of pllutonium in alkaline salt solutions

    International Nuclear Information System (INIS)

    Hobbs, D.T.; Edwards, T.B.

    1993-01-01

    Plutonium solubility data from several studies have been evaluated. For each data set, a predictive model has been developed where appropriate. In addition, a statistical model and corresponding prediction intervals for plutonium solubility as a quadratic function of the hydroxide concentration have been developed. Because of the wide range of solution compositions, the solubility of plutonium can vary by as much as three orders of magnitude for any given hydroxide concentration and still remain within the prediction interval. Any nuclear safety assessments that depend on the maximum amount of plutonium dissolved in alkaline salt solutions should use concentrations at least as great as the upper prediction limits developed in this study. To increase the confidence in the prediction model, it is recommended that additional solubility tests be conducted at low hydroxide concentrations and with all of the other solution components involved. To validate the model for application to actual waste solutions, it is recommended that the plutonium solubilities in actual waste solutions be determined and compared to the values predicted by the quadratic model

  7. Blending of Radial HF Radar Surface Current and Model Using ETKF Scheme For The Sunda Strait

    Science.gov (United States)

    Mujiasih, Subekti; Riyadi, Mochammad; Wandono, Dr; Wayan Suardana, I.; Nyoman Gede Wiryajaya, I.; Nyoman Suarsa, I.; Hartanto, Dwi; Barth, Alexander; Beckers, Jean-Marie

    2017-04-01

    Preliminary study of data blending of surface current for Sunda Strait-Indonesia has been done using the analysis scheme of the Ensemble Transform Kalman Filter (ETKF). The method is utilized to combine radial velocity from HF Radar and u and v component of velocity from Global Copernicus - Marine environment monitoring service (CMEMS) model. The initial ensemble is based on the time variability of the CMEMS model result. Data tested are from 2 CODAR Seasonde radar sites in Sunda Strait and 2 dates such as 09 September 2013 and 08 February 2016 at 12.00 UTC. The radial HF Radar data has a hourly temporal resolution, 20-60 km of spatial range, 3 km of range resolution, 5 degree of angular resolution and spatial resolution and 11.5-14 MHz of frequency range. The u and v component of the model velocity represents a daily mean with 1/12 degree spatial resolution. The radial data from one HF radar site is analyzed and the result compared to the equivalent radial velocity from CMEMS for the second HF radar site. Error checking is calculated by root mean squared error (RMSE). Calculation of ensemble analysis and ensemble mean is using Sangoma software package. The tested R which represents observation error covariance matrix, is a diagonal matrix with diagonal elements equal 0.05, 0.5 or 1.0 m2/s2. The initial ensemble members comes from a model simulation spanning a month (September 2013 or February 2016), one year (2013) or 4 years (2013-2016). The spatial distribution of the radial current are analyzed and the RMSE values obtained from independent HF radar station are optimized. It was verified that the analysis reproduces well the structure included in the analyzed HF radar data. More importantly, the analysis was also improved relative to the second independent HF radar site. RMSE of the improved analysis is better than first HF Radar site Analysis. The best result of the blending exercise was obtained for observation error variance equal to 0.05 m2/s2. This study is

  8. Interlaboratory validation of small-scale solubility and dissolution measurements of poorly water-soluble drugs

    DEFF Research Database (Denmark)

    Andersson, Sara B. E.; Alvebratt, Caroline; Bevernage, Jan

    2016-01-01

    The purpose of this study was to investigate the interlaboratory variability in determination of apparent solubility (Sapp) and intrinsic dissolution rate (IDR) using a miniaturized dissolution instrument. Three poorly water-soluble compounds were selected as reference compounds and measured at m...

  9. Effect of cyclodextrin complexation on the aqueous solubility and solubility/dose ratio of praziquantel.

    Science.gov (United States)

    Maragos, Stratos; Archontaki, Helen; Macheras, Panos; Valsami, Georgia

    2009-01-01

    Praziquantel (PZQ), the primary drug of choice in the treatment of schistosomiasis, is a highly lipophilic drug that possesses high permeability and low aqueous solubility and is, therefore, classified as a Class II drug according to the Biopharmaceutics Classification System (BCS). In this work, beta-cyclodextrin (beta-CD) and hydroxypropyl-beta-cyclodextrin (HP-beta-CD) were used in order to determine whether increasing the aqueous solubility of a drug by complexation with CDs, a BCS-Class II compound like PZQ could behave as BCS-Class I (highly soluble/highly permeable) drug. Phase solubility and the kneading and lyophilization techniques were used for inclusion complex preparation; solubility was determined by UV spectroscopy. The ability of the water soluble polymer polyvinylpyrolidone (PVP) to increase the complexation and solubilization efficiency of beta-CD and HP-beta-CD for PZQ was examined. Results showed significant improvement of PZQ solubility in the presence of both cyclodextrins but no additional effect in the presence of PVP. The solubility/dose ratios values of PZQ-cyclodextrin complexes calculated considering the low (150 mg) and the high dose (600 mg) of PZQ, used in practice, indicate that PZQ complexation with CDs may result in drug dosage forms that would behave as a BCS-Class I depending on the administered dose.

  10. Evolution of Zr/Hf/Zr trilayers during annealing studied by RBS

    International Nuclear Information System (INIS)

    Kling, A.; Soares, J.C.

    2010-01-01

    The Zr/Hf system is highly interesting due its various applications, e.g. formation of amorphous ternary alloys, superconductive properties and production of gate oxide layers with high dielectric coefficients by oxidation of Zr/Hf multilayers. In this work Zr/Hf/Zr trilayers with an individual layer thickness of approximately 50 nm were deposited by electron gun evaporation on a substrate consisting of silicon covered by a micrometer thick thermal oxide layer. Samples were subjected to annealing procedures at 500 and 1200 o C in flowing air atmosphere to promote oxidation and Zr/Hf interdiffusion effects. RBS studies of the as-deposited and annealed samples were performed at the van-de-Graaff accelerator of ITN using He + and H + beams with energies between 2.0 and 2.525 MeV in order to study compositional changes induced by the heat treatment. In the case of low-temperature annealing the layer system appears, besides the oxidation process starting from the surface, to be stable. On the other hand, high-temperature annealing leads to an asymmetric Hf-diffusion into the surface and interior Zr-layer provoked by anomalous diffusion due to a phase transition in Zr accompanied by an almost complete oxidation of the layer structure Oxygen and metal depth distributions obtained by RBS in the as-deposited and treated samples are provided.

  11. Glass forming ability: Miedema approach to (Zr, Ti, Hf)-(Cu, Ni) binary and ternary alloys

    Energy Technology Data Exchange (ETDEWEB)

    Basu, Joysurya [Department of Chemical, Materials and Biomolecular Engineering, 191 Auditorium Road, University of Connecticut, Storrs 06269, CT (United States)], E-mail: jbasu@engr.uconn.edu; Murty, B.S. [Department of Metallurgical and Materials Engineering, Indian Institute of Technology Madras, Chennai 600036 (India); Ranganathan, S. [Department of Materials Engineering, Indian Institute of Science, Bangalore 560012 (India)

    2008-10-06

    Miedema's approach has been useful in determining the glass forming composition range for a particular alloy system. The concept of mixing enthalpy and mismatch entropy can be used in order to quantify Inoue's criteria of bulk metallic glass formation. In the present study, glass forming composition range has been determined for different binary and ternary (Zr, Ti, Hf)-(Cu, Ni) alloys based on the mixing enthalpy and mismatch entropy calculations. Though copper and nickel appear next to each other in the periodic table, the glass forming ability of the copper and nickel bearing alloys is different. Thermodynamic analysis reveals that the glass forming behaviour of Zr and Hf is similar, whereas it is different from that of Ti. The smaller atomic size of Ti and the difference in the heat of mixing of Ti, Zr, Hf with Cu and Ni leads to the observed changes in the glass forming behaviour. Enthalpy contour plots can be used to distinguish the glass forming compositions on the basis of the increasing negative enthalpy of the composition. This method reveals the high glass forming ability of binary Zr-Cu, Hf-Cu, Hf-Ni systems over a narrow composition range.

  12. HF treatment effect for carbon deposition on silicon (111) by DC sputtering technique

    Energy Technology Data Exchange (ETDEWEB)

    Aji, A. S., E-mail: aji.ravazes70@gmail.com; Darma, Y., E-mail: aji.ravazes70@gmail.com [Quantum Semiconductor and Devices Lab., Physics of Material Electronics Research Division, Department of Physics, Institut Teknologi Bandung (Indonesia)

    2014-03-24

    Surface modifications of Si (111) substrate by HF solution for thin film carbon deposition have been systematically studied. Thin film carbon on Si (111) has been deposited using DC Unbalanced Magnetron Sputtering with carbon pellet doped by 5% Fe as the target. EDAX characterization confirmed that the carbon fraction on Si substrate much higher by dipping a clean Si substrate by HF solution before sputtering process in comparison with carbon fraction on Si substrate just after conventional RCA. Moreover, SEM and AFM images show the uniform thin film carbon on Si with HF treatment, in contrast to the Si without HF solution treatment. These experimental results suggest that HF treatment of Si surface provide Si-H bonds on top Si surface that useful to enhance the carbon deposition during sputtering process. Furthermore, we investigate the thermal stability of thin film carbon on Si by thermal annealing process up to 900 °C. Atomic arrangements during annealing process were characterized by Raman spectroscopy. Raman spectra indicate that thin film carbon on Si is remaining unchanged until 600 °C and carbon atoms start to diffuse toward Si substrate after annealing at 900 °C.

  13. Oxygen vacancy effects in HfO2-based resistive switching memory: First principle study

    Directory of Open Access Journals (Sweden)

    Yuehua Dai

    2016-08-01

    Full Text Available The work investigated the shape and orientation of oxygen vacancy clusters in HfO2-base resistive random access memory (ReRAM by using the first-principle method based on the density functional theory. Firstly, the formation energy of different local Vo clusters was calculated in four established orientation systems. Then, the optimized orientation and charger conductor shape were identified by comparing the isosurface plots of partial charge density, formation energy, and the highest isosurface value of oxygen vacancy. The calculated results revealed that the [010] orientation was the optimal migration path of Vo, and the shape of system D4 was the best charge conductor in HfO2, which effectively influenced the SET voltage, formation voltage and the ON/OFF ratio of the device. Afterwards, the PDOS of Hf near Vo and total density of states of the system D4_010 were obtained, revealing the composition of charge conductor was oxygen vacancy instead of metal Hf. Furthermore, the migration barriers of the Vo hopping between neighboring unit cells were calculated along four different orientations. The motion was proved along [010] orientation. The optimal circulation path for Vo migration in the HfO2 super-cell was obtained.

  14. Temporal evolution of the HF-enhanced plasma line in sporadic E

    International Nuclear Information System (INIS)

    Djuth, F.T.; Gonzales, C.A.

    1988-01-01

    The high-power, high-frequency (HF) facility at Arecibo, Puerto Rico, has been used to study the excitation of Langmuir waves in mid-latitude sporadic E. Measurements of the temporal evolution of so-called HF-enhanced plasma line (HFPL) were made using the Arecibo 430-MHz radar. After HF turn-on in the plasma the HFPL exhibits a rapid growth phase followed by a quick overshoot. During periods of strong HFPL excitation the e-folding growth time of the HFPL power is typically approx-lt 20 μs, and the total overshoot period is ∼1 ms. On the basis of the current observations, mode conversion of the HF wave into Langmuir waves near HF reflection appears to be a promising mechanism for the production of Langmuir waves in sporadic E. Caviton formation at the critical layer is expected to accompany this process, and there is some evidence that the 430-MHz radar is probing the plasma in a region where density cavities of this nature form. While no specific explanation is offered for the HFPL overshoot, it appears that this phenomenon is fundamental to the Langmuir wave excitation process

  15. Influence of annealing on structure and magnetic properties of Laves phase HfFe2

    International Nuclear Information System (INIS)

    Belosevic-Cavor, J.; Cekic, B.; Novakovic, N.; Ivanovic, N.; Manasijevic, M.

    2004-01-01

    Hyperfine fields (HFF) in a polycrystalline HfFe 2 binary compound were measured at 181 Ta probe ion sites using the time differential perturbed angular correlation (TDPAC) method. Analysis of TDPAC spectra obtained in measurements revealed two components. One of them corresponded to the magnetic perturbation with the value B hf1 (Ta) = 13.82(7) T at room temperature and it was ascribed to the interaction at the regular position of Hf in the cubic C15 (MgCu 2 -type) structure of the HfFe 2 compound. The second component with hyperfine field value of B hf2 (Ta) = 8.0(2) T is probably due to the presence of a minor amount of the hexagonal C14 (MgZn 2 -type) structure. Measurements showed that it had come to a change in the ratio of different components of TDPAC spectra with annealing, but the values for hyperfine fields for both components have not changed significantly. The origin of the hyperfine magnetic field and its difference in the two structures (C14 and C15) were discussed taking into account crystal structure effects. (orig.)

  16. Thermal evolution of CaO-doped HfO{sub 2} films and powders

    Energy Technology Data Exchange (ETDEWEB)

    Barolin, S A; Sanctis, O A de [Lab. Materiales Ceramicos, FCEIyA, Universidad Nacional de Rosario, IFIR-CONICET (Argentina); Caracoche, M C; Martinez, J A; Taylor, M A; Pasquevich, A F [Departamento de Fisica, FCE, Universidad Nacional de La Plata, IFLP-CONICET (Argentina); Rivas, P C, E-mail: oski@fceia.unr.edu.a [Facultad de Ciencias Agronomicas y Forestales, Universidad Nacional de La Plata, IFLP (Argentina)

    2009-05-01

    Solid solutions of ZrO2 and HfO2 are potential electrolyte materials for intermediate-temperature SOFC because both are oxygen-ion conductors. The main challenge for these compounds is to reduce the relatively high value of the activation energies vacancies diffusion, which is influenced by several factors. In this work the thermal evolution of CaO-HfO{sub 2} materials have been investigated. (CaO)y-Hf(1-y)O(2-y) (y = 0.06, 0.14 y 0.2) coatings and powders were synthesized by chemical solution deposition (CSD). Films were deposited onto alumina substrates by Dip Coating technique, the burning of organic waste was carried out at 500 deg. C under normal atmosphere and then the films were thermally treated at intervals of temperature rising to a maximum temperature of 1250 deg. C. By means Glazing Incidence X-ray Diffraction (rho-2theta configuration) the phases were studied in the annealed films. On the other hand, the thermal evolution and crystallization process of powders were analyzed in-situ by HT-XRD. The phenomena crystallization occurred in films and powders were analyzed. The activation energies of diffusion of oxygen vacancies of HfO2-14 mole% CaO and HfO2-20 mole% CaO films were measured from the thermal evolution of the relaxation constant measured by Perturbed Angular Correlation Technique.

  17. Designer HF-Based Fluorination Reagent: Highly Regioselective Synthesis of Fluoroalkenes and gem-Difluoromethylene Compounds from Alkynes

    Science.gov (United States)

    2015-01-01

    Hydrogen fluoride (HF) and selected nonbasic and weakly coordinating (toward cationic metal) hydrogen-bond acceptors (e.g., DMPU) can form stable complexes through hydrogen bonding. The DMPU/HF complex is a new nucleophilic fluorination reagent that has high acidity and is compatible with cationic metal catalysts. The gold-catalyzed mono- and dihydrofluorination of alkynes using the DMPU/HF complex yields synthetically important fluoroalkenes and gem-difluoromethlylene compounds regioselectively. PMID:25260170

  18. Solubilities of boric acid in heavy water

    International Nuclear Information System (INIS)

    Nakai, Shigetsugu; Aoi, Hideki; Hayashi, Ken-ichi; Katoh, Taizo; Watanabe, Takashi.

    1988-01-01

    A gravimetric analysis using meta-boric acid (HBO 2 or DBO 2 ) as a weighing form has been developed for solubility measurement. The method gave satisfactory results in preliminary measurement of solubilities of boric acid in light water. By using this method, the solubilities of 10 B enriched D 3 BO 3 in heavy water were measured. The results are as follows; 2.67 (7deg C), 3.52 (15deg C), 5.70 (30deg C), 8.87 (50deg C) and 12.92 (70deg C) w/o, respectively. These values are about 10% lower than those in light water. Thermodynamical consideration based on the data shows that boric acid is the water structure breaker. (author)

  19. Resveratrol cocrystals with enhanced solubility and tabletability.

    Science.gov (United States)

    Zhou, Zhengzheng; Li, Wanying; Sun, Wei-Jhe; Lu, Tongbu; Tong, Henry H Y; Sun, Changquan Calvin; Zheng, Ying

    2016-07-25

    Two new 1:1 cocrystals of resveratrol (RES) with 4-aminobenzamide (RES-4ABZ) and isoniazid (RES-ISN) were synthesized by liquid assisted grinding (LAG) and rapid solvent removal (RSR) methods using ethanol as solvent. Their physiochemical properties were characterized using PXRD, DSC, solid state and solution NMR, FT-IR, and HPLC. Pharmaceutically relevant properties, including tabletability, solubility, intrinsic dissolution rate, and hygroscopicity, were evaluated. Temperature-composition phase diagram for RES-ISN cocrystal system was constructed from DSC data. Both cocrystals show higher solubility than resveratrol over a broad range of pH. They are phase stable and non-hygroscopic even under high humidity conditions. Importantly, both cocrystals exhibit improved solubility and tabletability compared with RES, which make them more suitable candidates for tablet formulation development. Copyright © 2016 Elsevier B.V. All rights reserved.

  20. AW-101 entrained solids - Solubility versus temperature

    International Nuclear Information System (INIS)

    GJ Lumetta; RC Lettau; GF Piepel

    2000-01-01

    This report describes the results of a test conducted by Battelle to assess the solubility of the solids entrained in the diluted AW-101 low-activity waste (LAW) sample. BNFL requested Battelle to dilute the AW-1-1 sample using de-ionized water to mimic expected plant operating conditions. BNFL further requested Battelle to assess the solubility of the solids present in the diluted AW-101 sample versus temperature conditions of 30, 40, and 50 C. BNFL requested these tests to assess the composition of the LAW supernatant and solids versus expected plant-operating conditions. The work was conducted according to test plan BNFL-TP-29953-7, Rev. 0, Determination of the Solubility of LAW Entrained Solids. The test went according to plan, with no deviations from the test plan

  1. Solubility and stability of inorganic carbonates

    International Nuclear Information System (INIS)

    Taylor, P.

    1987-01-01

    The chemistry of inorganic carbonates is reviewed, with emphasis on solubility and hydrolytic stability, in order to identify candidate waste forms for immobilization and disposal of 14 C. At present, CaCO 3 and BaCO 3 are the two most widely favoured wasted forms, primarily because they are the products of proven CO 2 -scrubbing technology. However, they have relatively high solubilities in non-alkaline solutions, necessitating care in selecting and assessing an appropriate disposal environment. Three compounds with better solubility characteristics in near-neutral waters are identified: bismutite, (BiO) 2 CO 3 ; hydrocerussite, Pb 3 (OH) 2 (CO 3 ) 2 ; and rhodochrosite, MnCO 3 . Some of the limitations of each of these alternative waste forms are discussed

  2. A framework for API solubility modelling

    DEFF Research Database (Denmark)

    Conte, Elisa; Gani, Rafiqul; Crafts, Peter

    . In addition, most of the models are not predictive and requires experimental data for the calculation of the needed parameters. This work aims at developing an efficient framework for the solubility modelling of Active Pharmaceutical Ingredients (API) in water and organic solvents. With this framework......-SAFT) are used for solubility calculations when the needed interaction parameters or experimental data are available. The CI-UNIFAC is instead used when the previous models lack interaction parameters or when solubility data are not available. A new GC+ model for APIs solvent selection based...... on the hydrophobicity, hydrophilicity and polarity information of the API and solvent is also developed, for performing fast solvent selection and screening. Eventually, all the previous developments are integrated in a framework for their efficient and integrated use. Two case studies are presented: the first...

  3. Solubility of iron in liquid lead

    International Nuclear Information System (INIS)

    Ali-Khan, I.

    1981-01-01

    The use of liquid lead in high temperature chemical and metallurgical processes is well known. The structural materials applied for the containment of these processes are either iron base alloys or possess iron as an alloying element. Besides that, lead itself is alloyed in some steels to achieve some very useful properties. For understanding the effect of liquid lead in such structural materials, it is important to determine the solubility of iron in liquid lead which would also be indicative of the stability of these alloys. At the institute of reactor materials of KFA Juelich, investigations have been conducted to determine the solubility of iron in liquid lead up to a temperature of about 1000 0 C. In this presentation the data concerning the solubility of iron in liquid lead are brought up to date and discussed including the results of our previous investigations. (orig.)

  4. Equilibrium Solubility of CO2 in Alkanolamines

    DEFF Research Database (Denmark)

    Waseem Arshad, Muhammad; Fosbøl, Philip Loldrup; von Solms, Nicolas

    2014-01-01

    Equilibrium solubility of CO2 were measured in aqueous solutions of Monoethanolamine (MEA) and N,N-diethylethanolamine(DEEA). Equilibrium cells are generally used for these measurements. In this study, the equilibrium data were measured from the calorimetry. For this purpose a reaction calorimeter...... (model CPA 122 from ChemiSens AB, Sweden) was used. The advantage of this method is being the measurement of both heats of absorption and equilibrium solubility data of CO2 at the same time. The measurements were performed for 30 mass % MEA and 5M DEEA solutions as a function of CO2 loading at three...... different temperatures 40, 80 and 120 ºC. The measured 30 mass % MEA and 5M DEEA data were compared with the literature data obtained from different equilibrium cells which validated the use of calorimeters for equilibrium solubility measurements....

  5. Respiratory carcinogenicity assessment of soluble nickel compounds.

    Science.gov (United States)

    Oller, Adriana R

    2002-10-01

    The many chemical forms of nickel differ in physicochemical properties and biological effects. Health assessments for each main category of nickel species are needed. The carcinogenicity assessment of water-soluble nickel compounds has proven particularly difficult. Epidemiologic evidence indicates an association between inhalation exposures to nickel refinery dust containing soluble nickel compounds and increased risk of respiratory cancers. However, the nature of this association is unclear because of limitations of the exposure data, inconsistent results across cohorts, and the presence of mixed exposures to water-insoluble nickel compounds and other confounders that are known or suspected carcinogens. Moreover, well-conducted animal inhalation studies, where exposures were solely to soluble nickel, failed to demonstrate a carcinogenic potential. Similar negative results were seen in animal oral studies. A model exists that relates respiratory carcinogenic potential to the bioavailability of nickel ion at nuclear sites within respiratory target cells. This model helps reconcile human, animal, and mechanistic data for soluble nickel compounds. For inhalation exposures, the predicted lack of bioavailability of nickel ion at target sites suggests that water-soluble nickel compounds, by themselves, will not be complete human carcinogens. However, if inhaled at concentrations high enough to induce chronic lung inflammation, these compounds may enhance carcinogenic risks associated with inhalation exposure to other substances. Overall, the weight of evidence indicates that inhalation exposure to soluble nickel alone will not cause cancer; moreover, if exposures are kept below levels that cause chronic respiratory toxicity, any possible tumor-enhancing effects (particularly in smokers) would be avoided.

  6. SITE-94. Radionuclide solubilities for SITE-94

    Energy Technology Data Exchange (ETDEWEB)

    Arthur, R.; Apted, M. [QuantiSci, Denver, CO (United States)

    1996-12-01

    In this report, solubility constraints are evaluated on radioelement source-term concentrations supporting the SITE-94 performance assessment. Solubility models are based on heterogeneous-equilibrium, mass- and charge-balance constraints incorporated into the EQ3/6 geochemical software package, which is used to calculate the aqueous speciation behavior and solubilities of U, Th, Pu, Np, Am, Ni, Ra, Se, Sn, Sr, Tc and Zr in site groundwaters and near-field solutions. The chemical evolution of the near field is approximated using EQ3/6 in terms of limiting conditions at equilibrium, or steady state, in three closed systems representing fully saturated bentonite, Fe{sup o} corrosion products of the canister, and spent fuel. The calculations consider both low-temperature (15 deg C) and high-temperature (80 deg C) conditions in the near field, and the existence of either reducing or strongly oxidizing conditions in each of the bentonite, canister, and spent-fuel barriers. Heterogeneities in site characteristics are evaluated through consideration of a range of initial groundwaters and their interactions with engineered barriers. Aqueous speciation models for many radioelements are constrained by thermodynamic data that are estimated with varying degrees of accuracy. An important question, however, is how accurate do these models need to be for purposes of estimating source-term concentrations? For example, it is unrealistic to expect a high degree of accuracy in speciation models if such models predict solubilities that are below the analytical detection limit for a given radioelement. From a practical standpoint, such models are irrelevant if calculated solubilities cannot be tested by direct comparison to experimental data. In the absence of models that are both accurate and relevant for conditions of interest, the detection limit could define a pragmatic upper limit on radioelement solubility 56 refs, 25 tabs, 10 figs

  7. SITE-94. Radionuclide solubilities for SITE-94

    International Nuclear Information System (INIS)

    Arthur, R.; Apted, M.

    1996-12-01

    In this report, solubility constraints are evaluated on radioelement source-term concentrations supporting the SITE-94 performance assessment. Solubility models are based on heterogeneous-equilibrium, mass- and charge-balance constraints incorporated into the EQ3/6 geochemical software package, which is used to calculate the aqueous speciation behavior and solubilities of U, Th, Pu, Np, Am, Ni, Ra, Se, Sn, Sr, Tc and Zr in site groundwaters and near-field solutions. The chemical evolution of the near field is approximated using EQ3/6 in terms of limiting conditions at equilibrium, or steady state, in three closed systems representing fully saturated bentonite, Fe o corrosion products of the canister, and spent fuel. The calculations consider both low-temperature (15 deg C) and high-temperature (80 deg C) conditions in the near field, and the existence of either reducing or strongly oxidizing conditions in each of the bentonite, canister, and spent-fuel barriers. Heterogeneities in site characteristics are evaluated through consideration of a range of initial groundwaters and their interactions with engineered barriers. Aqueous speciation models for many radioelements are constrained by thermodynamic data that are estimated with varying degrees of accuracy. An important question, however, is how accurate do these models need to be for purposes of estimating source-term concentrations? For example, it is unrealistic to expect a high degree of accuracy in speciation models if such models predict solubilities that are below the analytical detection limit for a given radioelement. From a practical standpoint, such models are irrelevant if calculated solubilities cannot be tested by direct comparison to experimental data. In the absence of models that are both accurate and relevant for conditions of interest, the detection limit could define a pragmatic upper limit on radioelement solubility

  8. Hydrogen solubility in austenite of Fe-Ni-Cr alloys

    International Nuclear Information System (INIS)

    Zhirnova, V.V.; Mogutnov, B.M.; Tomilin, I.A.

    1981-01-01

    Hydrogen solubility in Fe-Ni-Cr alloys at 600-1000 deg C is determined. Hydrogen solubility in ternary alloys can not be predicted on the basis of the data on its solubility in binary Fe-Ni, Fe-Cr alloys. Chromium and nickel effect on hydrogen solubility in iron is insignificant in comparison with the effect of these elements on carbon or nitrogen solubility [ru

  9. Thermally-driven H interaction with HfO2 films deposited on Ge(100) and Si(100)

    Science.gov (United States)

    Soares, G. V.; Feijó, T. O.; Baumvol, I. J. R.; Aguzzoli, C.; Krug, C.; Radtke, C.

    2014-01-01

    In the present work, we investigated the thermally-driven H incorporation in HfO2 films deposited on Si and Ge substrates. Two regimes for deuterium (D) uptake were identified, attributed to D bonded near the HfO2/substrate interface region (at 300 °C) and through the whole HfO2 layer (400-600 °C). Films deposited on Si presented higher D amounts for all investigated temperatures, as well as, a higher resistance for D desorption. Moreover, HfO2 films underwent structural changes during annealings, influencing D incorporation. The semiconductor substrate plays a key role in this process.

  10. Evaluation of soluble organic compounds generated by radiological degradation of asphalt

    International Nuclear Information System (INIS)

    Fukumoto, M.; Nishikawa, Y.; Kagawa, A.; Kawamura, K.

    2000-12-01

    The soluble organic compounds generated by radiological degradation of asphalt (γ ray) were confirmed as a part of influence of the bituminized waste degradation in the TRU waste repository. Especially, the influence of the nitrate was focused on. As a result, the concentration of the soluble organic compounds generated by radiological degradation of asphalt (10 MGy, γ ray which is correspond to absorbed dose of asphalt for 1,000,000 years) were lower (each formic acid: about 50 mg/dm 3 , acetic acid: about 30 mg/dm 3 and oxalic acid: about 2 mg/dm 3 ) than that of the formic acid, the acetic acid and the oxalic acid which Valcke et al. had shown (the influence of the organic at the solubility examination which uses Pu and Am). Moreover, the change in the concentration of TOC and the soluble organic compounds (formic acid, acetic acid and oxalic acid) is little under the existence of nitrate ion. That is, the formic acid and acetic acid which can be organic ligands were generated little by oxidative decomposition of asphalt in the process that nitrate ion becomes nitride ion by radiation. The influence of the soluble organic compounds by the radiological degradation of the asphalt (γ ray) on adsorption and solubility by the complexation of radionuclides in the performance assessment can be limited. (author)

  11. Solubility investigation of ether and ester essential oils in water using spectrometry and GC/MS

    Directory of Open Access Journals (Sweden)

    B. Khodabandeloo

    2017-11-01

    Full Text Available Background and objectives: Essential oils (volatiles are aromatic oily liquids prepared from different parts of plants and demonstrate various therapeutic and cosmetic properties. The dissolution of essential oils are not desirable in water, therefore the aim of this research was evaluation and selection the best co-solvents for increasing their solubility and bio availability. Methods:The solubility of six  plants essential oils were investigated in presence of propylene glycol (PG, polyethylene glycol 300 (PEG, glycerin and ethanol as solvent and tween 80 or lecithin as co-solvent by observation and spectrophotometric assay. Chemical composition of the essential oils and supersaturated 50% ethanol (SSE and 50% PG or PEG (SSP solutions were analyzed by GC/MS, too. Results: Ester (Lavandula dentata, Heracleum persicum and, Elettaria cardamomum essential oils showed the best solubility in ethanol and PG, respectively. Ether (Foeniculum vulgare, Pimpinella anisum and Petroselinum crispum essential oils had the best solubility in ethanol and PEG, respectively. In ester class, mixture of ethanol/water was the best solvent according to solubility and total amounts of major compounds of the essential oils. In ether class, all samples had better solubility in mixtures of ethanol/water than PEG, but the amounts of total phenols or ethers in SSP of some samples were higher than SSE. Therefore selecting the best solvent for these class need more experiments. Conclusion: Selecting the solvent for essential oils changes their chemical composition; therefore the best solvent was different for various purposes.

  12. Assessment of the fears of the public concerning possible hazards from HF electromagnetic fields of mobile phone equipment - annual enquiries. Final report on the enquiry of 2005

    International Nuclear Information System (INIS)

    Belz, Janina

    2007-01-01

    The BfS (Bundesamt fuer Strahlenschutz, Federal Radiation Protection Office) carries out a continuous series of investigations on citizens' fears concerning the potential hazards of HF electromagnetic fields emitted by mobile phones (''Ermittlung der Befuerchtungen und Aengste der breiten Oeffentlichkeit hinsichtlich moeglicher Gefahren der hochfrequenten elektromagnetischen Felder des Mobilfunks''). For this purpose, enquiries by telephone were carried out annually between 2003 and 2006 among representative parts of the population by the Institut fuer angewandte Sozialwissenschaft. These are to investigate the awareness of the population of health risks of electromagnetic fields and also show changes in awareness over the period under investigation. (orig.) [de

  13. Hydrogen terminal solubility in Zircaloy-4

    International Nuclear Information System (INIS)

    Vizcaino, Pablo; Banchik, Abrahan D.

    1999-01-01

    Terminal solubility temperature of hydrogen in zirconium and its alloys is an important parameter because hydrides precipitation embrittled these materials making them susceptible to the phenomenon known as retarded hydrogen cracking. This work continues the study presented in the 25 AATN Meeting. Within this framework, a study focused on determining these curves in recrystallized Zircaloy-4, using scanning differential calorimetric technique. Terminal solubility curves for Zircaloy-4 were constructed within a concentration range from 40 to 640 ppm in hydrogen weight and comparisons with results obtained by other authors were made. (author)

  14. Nitrogen solubility in nickel base multicomponent melts

    International Nuclear Information System (INIS)

    Bol'shov, L.A.; Stomakhin, A.Ya.; Sokolov, V.M.; Teterin, V.G.

    1984-01-01

    Applicability of various methods for calculation of nitrogen solubility in high-alloyed nickel base alloys, containing Cr, Fe, W, Mo, Ti, Nb, has been estimated. A possibility is shown to use the formUla, derived for the calculation of nitrogen solubility in iron on the basis of statistical theory for a grid model of solution which does not require limitations for the content of a solvent component. The calculation method has been used for nickel alloys, with the concentration of solvent, iron, being accepted equal to zero, and employing parameters of nitrogen interaction as determined for iron-base alloys

  15. Effect of amides on lithium tetraborate solubility

    Energy Technology Data Exchange (ETDEWEB)

    Tsekhanskij, R S; Skvortsov, V C; Molodkin, A K; Sadetdi-pov, Sh V [Chuvashskij Gosudarstvennyj Pedagogicheskij Inst., Cheboksary (USSR); Universitet Druzhby Narodov, Moscow (USSR))

    1983-03-01

    Using the methods of solubility, densi- and refractometry at 25 deg C, it has been established that the systems lithium tetraborate-formamide (acetamide, dimethyl-formamide)-water are of a simple eutonic type. Amides decrease the salt solubility. Lyotropic effect, as calculated for molar concentrations (-Lsub(M)) relative to the absolute value, increases from formamide to dimethyl-formamide. The sequence is determined by the fact that, when there is one or two hydrophilic methyl groups in amide molecules which are in contact with tetraborate, they decrease the hydration energy of lithium cations.

  16. Effect of amides on sodium tetraborate solubility

    International Nuclear Information System (INIS)

    Tsekhanskij, R.S.; Skvortsov, V.G.; Molodkin, A.K.; Sadetdinov, Sh.V.

    1986-01-01

    Methods of solubility and refractometry at 25 deg C were applied to investigate sodium tetraborate - formamide (dimethylformamide) - water systems. It is stated that they are of simple eutonic type as well as the earlier described sodium tetraborate-acetamide-water system. Amides reduce solubility of the salt. The effect of contact interaction between dissolved substances on salt cation hydration and thus on the value of liotropic amide effect is confirmed. This value is found to be also depend on the number of molecules of coordination water in the initial crystalline hydrate

  17. Effect of amides on lithium tetraborate solubility

    International Nuclear Information System (INIS)

    Tsekhanskij, R.S.; Skvortsov, V.C.; Molodkin, A.K.; Sadetdi- pov, Sh.V.

    1983-01-01

    Using the methods of solubility, densi- and refractometry at 25 deg C, it has been established that the systemS lithium tetraborate-formamide (acetamide, dimethyl-formamide)-water are of a simple eutonic type. Amides decrease the salt solubility. Lyotropic effect, as calculated for molar concentrations (-Lsub(M)) relative to the absolute value, increases from formamide to dimethylformamide. The sequence is determined by the fact that, when there is one or two hydrophilic methyl groups in amide molecules which are in contact with tetraborate, they decrease the hydration energy of lithium cations

  18. Effect of amides on sodium tetraborate solubility

    Energy Technology Data Exchange (ETDEWEB)

    Tsekhanskij, R S; Skvortsov, V G; Molodkin, A K; Sadetdinov, Sh V

    1986-11-01

    Methods of solubility and refractometry at 25 deg C were applied to investigate sodium tetraborate - formamide (dimethylformamide) - water systems. It is stated that they are of simple eutonic type as well as the earlier described sodium tetraborate-acetamide-water system. Amides reduce solubility of the salt. The effect of contact interaction between dissolved substances on salt cation hydration and thus on the value of liotropic amide effect is confirmed. This value is found to be also depend on the number of molecules of coordination water in the initial crystalline hydrate.

  19. Modeling of Salt Solubilities in Mixed Solvents

    DEFF Research Database (Denmark)

    Chiavone-Filho, O.; Rasmussen, Peter

    2000-01-01

    A method to correlate and predict salt solubilities in mixed solvents using a UNIQUAC+Debye-Huckel model is developed. The UNIQUAC equation is applied in a form with temperature-dependent parameters. The Debye-Huckel model is extended to mixed solvents by properly evaluating the dielectric...... constants and the liquid densities of the solvent media. To normalize the activity coefficients, the symmetric convention is adopted. Thermochemical properties of the salt are used to estimate the solubility product. It is shown that the proposed procedure can describe with good accuracy a series of salt...

  20. Lumbar myelography using water-soluble contrast media

    International Nuclear Information System (INIS)

    Langlotz, M.

    1981-01-01

    With the new water-soluble contrast media developed in the last 10 years, lumbar myelography has become a simple and low-risk diagnostic method of great value which is hardly ever omitted before surgery is undertaken. The book attempts a synopsis of radiology and clinical examinations. In its first part, the pathological, clinical, and radiological aspects of diseases of the lumbosacral spinal duct are reviewed. The second part contains more than 300 myelographic pictures in original size. Each of the myelograms is supplemented by the case history of the patient (anamnesis, neurological examination, therapy and course). Interpretation is facilitated by drawings at the beginning of each chapter which show the major pathological and radiological changes. (orig./MG) [de

  1. Intrinsic electron traps in atomic-layer deposited HfO{sub 2} insulators

    Energy Technology Data Exchange (ETDEWEB)

    Cerbu, F.; Madia, O.; Afanas' ev, V. V.; Houssa, M.; Stesmans, A. [Laboratory of Semiconductor Physics, Department of Physics and Astronomy, University of Leuven, 3001 Leuven (Belgium); Andreev, D. V. [Laboratory of Semiconductor Physics, Department of Physics and Astronomy, University of Leuven, 3001 Leuven (Belgium); Bauman Moscow State Technical University—Kaluga Branch, 248000 Kaluga, Moscow obl. (Russian Federation); Fadida, S.; Eizenberg, M. [Department of Materials Science and Engineering, Technion-Israel Institute of Technology, 32000 Haifa (Israel); Breuil, L. [imec, 3001 Leuven (Belgium); Lisoni, J. G. [imec, 3001 Leuven (Belgium); Institute of Physics and Mathematics, Faculty of Science, Universidad Austral de Chile, Valdivia (Chile); Kittl, J. A. [Laboratory of Semiconductor Physics, Department of Physics and Astronomy, University of Leuven, 3001 Leuven (Belgium); Advanced Logic Lab, Samsung Semiconductor, Inc., Austin, 78754 Texas (United States); Strand, J.; Shluger, A. L. [Department of Physics and Astronomy, University College London, London WC1E 6BT (United Kingdom)

    2016-05-30

    Analysis of photodepopulation of electron traps in HfO{sub 2} films grown by atomic layer deposition is shown to provide the trap energy distribution across the entire oxide bandgap. The presence is revealed of two kinds of deep electron traps energetically distributed at around E{sub t} ≈ 2.0 eV and E{sub t} ≈ 3.0 eV below the oxide conduction band. Comparison of the trapped electron energy distributions in HfO{sub 2} layers prepared using different precursors or subjected to thermal treatment suggests that these centers are intrinsic in origin. However, the common assumption that these would implicate O vacancies cannot explain the charging behavior of HfO{sub 2}, suggesting that alternative defect models should be considered.

  2. Calculation of the local power peaking near WWER-440 control assemblies with Hf plates

    International Nuclear Information System (INIS)

    Hegyi, Gy.; Hordosy, G.; Kereszturi, A.; Maraszy, Cs.; Temesvari, E.

    2003-01-01

    The original coupler design of the WWER-440 assemblies had the following well known deficiency: The relatively large amount of water in the coupler between the absorber and fuel port of the control assembly can cause undesirably sharp power peaking in the fuel rods next to the coupler. The power peaking can be especially high after control rod withdrawal when the coupler reached low burnup level region of the adjacent assembly. The modernized coupler design overcomes the original problem by applying a thin Hf plate in the critical region. The very complicated structure of the coupler requires the verification of the core design methods by high precision 3D Monte Carlo calculations. The paper presents an MCNP reference calculation on the control rod coupler benchmark with Hf absorber plates. The benchmark solution with the KARATE-440 code system is also presented. The need for treating the Hf burnout in the reflector region is investigated (Authors)

  3. The effects of sacubitril/valsartan on coronary outcomes in PARADIGM-HF

    DEFF Research Database (Denmark)

    Mogensen, Ulrik M.; Køber, Lars; Kristensen, Søren L.

    2017-01-01

    Background Angiotensin converting enzyme inhibitors (ACE-I), are beneficial both in heart failure with reduced ejection fraction (HF-REF) and after myocardial infarction (MI). We examined the effects of the angiotensin-receptor neprilysin inhibitor sacubitril/valsartan, compared with the ACE......-I enalapril, on coronary outcomes in PARADIGM-HF. Methods and results We examined the effect of sacubitril/valsartan compared with enalapril on the following outcomes: i) the primary composite endpoint of cardiovascular (CV) death or HF hospitalization, ii) a pre-defined broader composite including...... patients, compared with enalapril, sacubitril/valsartan reduced the risk of the primary outcome (HR 0.80 [0.73–0.87], P 

  4. The tensile behavior of Ti36Ni49Hf15 high temperature shape memory alloy

    International Nuclear Information System (INIS)

    Wang, Y.Q.; Zheng, Y.F.; Cai, W.; Zhao, L.C.

    1999-01-01

    Recently, ternary Ti-Ni-Hf alloys have attracted great interest in the field of high temperature shape memory materials research and development. Extensive studies have been made on its manufacture process, constitutional phases, phase transformation behavior, the structure, substructure and interface structure of martensite and the precipitation behavior during ageing. Yet up to date there is no report about the fundamental mechanical properties of Ti-Ni-Hf alloys, such as the stress-strain data, the variation laws of the yield strength and elongation with the temperature. In the present study, tensile tests at various temperatures are employed to investigate the mechanical behavior of Ti-Ni-Hf alloy with different matrix structures, from full martensite to full parent phase structure, with the corresponding deformation mechanism discussed

  5. SIMS study of oxygen diffusion in monoclinic HfO2

    Science.gov (United States)

    Mueller, Michael P.; De Souza, Roger A.

    2018-01-01

    The diffusion of oxygen in dense ceramics of monoclinic HfO2 was studied by means of (18O/16O) isotope exchange annealing and subsequent determination of isotope depth profiles by Secondary Ion Mass Spectrometry. Anneals were performed in the temperature range of 573 ≤T /K ≤ 973 at an oxygen partial pressure of p O2=200 mbar . All measured isotope profiles exhibited two features: the first feature, closer to the surface, was attributed mainly to slow oxygen diffusion in an impurity silicate phase; the second feature, deeper in the sample, was attributed to oxygen diffusion in bulk monoclinic HfO2 . The activation enthalpy of oxygen tracer diffusion in bulk HfO2 was found to be ΔHD∗≈0.5 eV .

  6. Dosimetry of ultraviolet radiation with BaHfO_3 powders

    International Nuclear Information System (INIS)

    Barrera A, A. A.; Aguilar D, G. A.; Guzman M, J.; Rivera M, T.; Ceron R, V.

    2016-10-01

    Ceramic materials based on pure barium hafnate (BaHfO_3) have been obtained as a powder by the co-precipitation method. The powders obtained have a cubic structure that favors the thermoluminescent and optical properties, through which a better detection of the non-ionizing radiation is allowed. With these powders various tests were performed in the ultraviolet range at different exposure times. These thermoluminescent (Tl) studies were carried out using a Tl 3500 hand held reader which yielded a brightness curve that ranged from room temperature to the 350 degrees Celsius. This BaHfO_3 response exhibits a broad brightness curve with a single peak centered around 225 degrees Celsius. Finally, is reported that there are materials of barium hafnate (BaHfO_3) doped with some rare earths (Eu, Tb) which, instead of improving the performance of the powders, decrease it, so that the use of intrinsic barium hafnate is the most appropriate. (Author)

  7. Effect of HF leaching on {sup 14}C dates of pottery

    Energy Technology Data Exchange (ETDEWEB)

    Goslar, Tomasz, E-mail: goslar@radiocarbon.pl [Faculty of Physics, Adam Mickiewicz University, ul. Umultowska 85, 61-614 Poznan (Poland); Poznan Radiocarbon Laboratory, ul. Rubiez 46, 61-612 Poznan (Poland); Kozlowski, Janusz [Institute of Archaeology, Jagiellonian University, ul. Golebia 11, 30-007 Krakow (Poland); Szmyt, Marzena [Institute for Eastern Studies, Adam Mickiewicz University, ul. 28 Czerwca 1956 nr 198, 61-486 Poznan (Poland); Czernik, Justyna [Poznan Radiocarbon Laboratory, ul. Rubiez 46, 61-612 Poznan (Poland)

    2013-01-15

    This paper presents the experiments with {sup 14}C dating of two potsherds, which contained carbon dispersed rather homogeneously in their clay fabric. After AAA treatment, the potsherds still appeared to be contaminated with young carbon, presumably connected with humic acids. To make removal of humic acids more effective, we treated the sherds with HF acid of different concentration. The {sup 14}C results obtained demonstrate that HF treatment indeed helps to remove humic contaminants, but it also mobilizes carbon bound to raw clay, which may make {sup 14}C dates too old. We conclude therefore, that using a simple combination of HF and AAA treatment seems insufficient in reliable {sup 14}C dating of carbon homogeneously dispersed in the volume of potsherds.

  8. Corrosion Characteristics of Ti-29Nb-xHf Ternary Alloy for Biomaterials

    Energy Technology Data Exchange (ETDEWEB)

    Pak, Sun Young; Choi, Han Chul [Chosun Univ., Kwangju (Korea, Republic of)

    2015-12-15

    The Cp-Ti and Ti-6Al-4V alloys were widely used for dental materials due to their mechanical properties and good corrosion resistance. However, Cp-Ti was known as bio-inert materials, Ti-6Al-4V alloy has a problem such as high Young modulus, potential loss of the surrounding bone, and to the release of potentially toxic ions from the alloy. To overcome this problem, Ti alloys containing Nb and Hf elements have been used for biomaterials due to low toxicity and high corrosion resistance. Especially, alloying element of Nb was known as β phase stabilizer. The β phase alloy was widely used to replace currently used implant materials. The corrosion resistances of Ti-29Nb-xHf ternary alloys were dependent on Hf content in oral environment solution.

  9. Charge storage and tunneling mechanism of Ni nanocrystals embedded HfOx film

    Science.gov (United States)

    Zhu, H. X.; Zhang, T.; Wang, R. X.; Zhang, Y. Y.; Li, L. T.; Qiu, X. Y.

    2016-05-01

    A nano-floating gate memory structure based on Ni nanocrystals (NCs) embedded HfOx film is deposited by means of radio-frequency magnetron sputtering. Microstructure investigations reveal that self-organized Ni-NCs with diameters of 4-8 nm are well dispersed in amorphous HfOx matrix. Pt/Ni-NCs embedded HfOx/Si/Ag capacitor structures exhibit voltage-dependent capacitance-voltage hysteresis, and a maximum flat-band voltage shift of 1.5 V, corresponding to a charge storage density of 6.0 × 1012 electrons/cm2, is achieved. These capacitor memory cells exhibit good endurance characteristic up to 4 × 104 cycles and excellent retention performance of 105 s, fulfilling the requirements of next generation non-volatile memory devices. Schottky tunneling is proven to be responsible for electrons tunneling in these capacitors.

  10. Atomic layer deposition of HfO2 on graphene through controlled ion beam treatment

    International Nuclear Information System (INIS)

    Kim, Ki Seok; Oh, Il-Kwon; Jung, Hanearl; Kim, Hyungjun; Yeom, Geun Young; Kim, Kyong Nam

    2016-01-01

    The polymer residue generated during the graphene transfer process to the substrate tends to cause problems (e.g., a decrease in electron mobility, unwanted doping, and non-uniform deposition of the dielectric material). In this study, by using a controllable low-energy Ar + ion beam, we cleaned the polymer residue without damaging the graphene network. HfO 2 grown by atomic layer deposition on graphene cleaned using an Ar + ion beam showed a dense uniform structure, whereas that grown on the transferred graphene (before Ar + ion cleaning) showed a non-uniform structure. A graphene–HfO 2 –metal capacitor fabricated by growing 20-nm thick HfO 2 on graphene exhibited a very low leakage current (<10 −11 A/cm 2 ) for Ar + ion-cleaned graphene, whereas a similar capacitor grown using the transferred graphene showed high leakage current.

  11. Charge storage and tunneling mechanism of Ni nanocrystals embedded HfO{sub x} film

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, H. X.; Zhang, T.; Wang, R. X.; Zhang, Y. Y.; Li, L. T.; Qiu, X. Y., E-mail: qxy2001@swu.edu.cn [School of Physical Science and Technology, Southwest University, Chongqing 400715 (China)

    2016-05-15

    A nano-floating gate memory structure based on Ni nanocrystals (NCs) embedded HfO{sub x} film is deposited by means of radio-frequency magnetron sputtering. Microstructure investigations reveal that self-organized Ni-NCs with diameters of 4-8 nm are well dispersed in amorphous HfO{sub x} matrix. Pt/Ni-NCs embedded HfO{sub x}/Si/Ag capacitor structures exhibit voltage-dependent capacitance-voltage hysteresis, and a maximum flat-band voltage shift of 1.5 V, corresponding to a charge storage density of 6.0 × 10{sup 12} electrons/cm{sup 2}, is achieved. These capacitor memory cells exhibit good endurance characteristic up to 4 × 10{sup 4} cycles and excellent retention performance of 10{sup 5} s, fulfilling the requirements of next generation non-volatile memory devices. Schottky tunneling is proven to be responsible for electrons tunneling in these capacitors.

  12. High-temperature grain size stabilization of nanocrystalline Fe–Cr alloys with Hf additions

    Energy Technology Data Exchange (ETDEWEB)

    Li, Lulu, E-mail: lli18@ncsu.edu; Saber, Mostafa; Xu, Weizong; Zhu, Yuntian; Koch, Carl C.; Scattergood, Ronald O.

    2014-09-08

    The influence of 1–4 at% Hf additions on the thermal stability of mechanically alloyed nanocrystalline Fe–14Cr alloys was studied in this work. XRD-calculated grain size and microhardness results were reported versus isochronal annealing treatments up to 1100 °C. Microstructural evolution was investigated using channeling contrast FIB imaging and TEM. Grain size of samples with 4 at% Hf was found to be maintained in the nanoscale range at temperatures up to 1000 °C. Zener pinning was considered as a major source of high temperature grain size stabilization. By comparing the Orowan strengthening contribution to the total hardness, the deviation of grain size predictions from the actual grain size in Fe–14Cr–4Hf suggests the presence of thermodynamic stabilization by the solute segregation to grain boundaries (GBs). A predictive thermodynamic model indicates that the thermodynamic stabilization can be expected.

  13. Study of the properties of internal oxidized Cu - Al - Ti - Hf alloys

    International Nuclear Information System (INIS)

    Solopov, V.I.; Daneliya, E.P.; Daneliya, G.V.; Lebasova, O.P.

    1982-01-01

    Investigation results of mechanical properties and electric conductivity of rods of internally oxidized alloys Cu-Al-Ti-Hf depending on chemical composition, varying in the limits ensuring the formation of disperse enough and evenly distributed over the volume oxide phase. (0-1%Al, 0-0.5%Ti, 0-0.3%Hf, the restcopper), in the process of internal oxidation are presented. Internally oxidized alloys Cu-Al-Ti-Hf have increased strength properties with insignificant increase of specific electric resistance as compared with the known internally oxidized alloys Cu-Al. At that, the best combination of physicomechanical properties is achieved at small contents of titanium (0.01-0.05%) and hafnium (0.01-0.1%)

  14. Hf{sub 3}Fe{sub 4}Sn{sub 4} and Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x}: Two stannide intermetallics with low-dimensional iron sublattices

    Energy Technology Data Exchange (ETDEWEB)

    Calta, Nicholas P. [Department of Chemistry, Northwestern University (United States); Kanatzidis, Mercouri G., E-mail: m-kanatzidis@northwestern.edu [Department of Chemistry, Northwestern University (United States); Materials Science Division, Argonne National Laboratory (United States)

    2016-04-15

    This article reports two new Hf-rich intermetallics synthesized using Sn flux: Hf{sub 3}Fe{sub 4}Sn{sub 4} and Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x}. Hf{sub 3}Fe{sub 4}Sn{sub 4} adopts an ordered variant the Hf{sub 3}Cu{sub 8} structure type in orthorhombic space group Pnma with unit cell edges of a=8.1143(5) Å, b=8.8466(5) Å, and c=10.6069(6) Å. Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x}, on the other hand, adopts a new structure type in Cmc2{sub 1} with unit cell edges of a=5.6458(3) Å, b=35.796(2) Å, and c=8.88725(9) Å for x=0. It exhibits a small amount of phase width in which Sn substitutes on one of the Fe sites. Both structures are fully three-dimensional and are characterized by pseudo one- and two-dimensional networks of Fe–Fe homoatomic bonding. Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x} exhibits antiferromagnetic order at T{sub N}=46(2) K and its electrical transport behavior indicates that it is a normal metal with phonon-dictated resistivity. Hf{sub 3}Fe{sub 4}Sn{sub 4} is also an antiferromagnet with a rather high ordering temperature of T{sub N}=373(5) K. Single crystal resistivity measurements indicate that Hf{sub 3}Fe{sub 4}Sn{sub 4} behaves as a Fermi liquid at low temperatures, indicating strong electron correlation. - Graphical abstract: Slightly different growth conditions in Sn flux produce two new intermetallic compounds: Hf{sub 3}Fe{sub 4}Sn{sub 4} and Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x}. - Highlights: • Single crystals of both Hf{sub 3}Fe{sub 4}Sn{sub 4} and Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x} were grown using Sn flux. • The crystal structures were determined using single crystal X-ray diffraction. • The Fe moments in Hf{sub 3}Fe{sub 4}Sn{sub 4} display AFM order below T{sub N}=373 K. • The Fe moments in Hf{sub 9}Fe{sub 4−x}Sn{sub 10+x} display AFM order below T{sub N}=46 K.

  15. Extreme Hf and light Fe isotopes in Archean komatiites - a remnant of very early mantle depletion?

    Science.gov (United States)

    Nebel, O.; Sossi, P.; Campbell, I. H.; Van Kranendonk, M. J.

    2014-12-01

    Hafnium isotope signatures in some Archean komatiites (ca. 3.5-3.0 billion years old) require a mantle source with a time-integrated Lu/Hf that exceeds average modern depleted mantle. Investigation of the timing and locus of parent-daughter fractionation in their mantle sources potentially constrains differentiation processes in the early Earth and their subsequent distribution and storage. In addition, they may help to constrain the Hf isotope evolution of the greater depleted mantle. In order to shed light on these processes, we discuss radiogenic Hf isotopes in conjunction with stable Fe isotope systematics in Archean komatiites from the Pilbara craton in Western Australia. Our findings indicate that, after careful evaluation of the effects of alteration, pristine samples are characterised by initial 176Hf/177Hf, which lie above the age-corrected depleted mantle, as a consequence of ancient melt extraction. Iron isotope systematics for these samples further point to a mantle source that is isotopically lighter than average modern depleted mantle, which is also consistent with melt-depletion. Taken together, these observations require a component of an old, super-depleted reservoir in the komatiite mantle source(s) that survived in the mantle for possibly hundreds of millions of years. The Lu/Hf of this refractory mantle appears to be complementary to, and therefore contemporaneous with, the first terrestrial crust, as preserved in Hadean (i.e., > 4 Ga) detrital zircon cores, which may indicate a causal relationship between them. We will discuss implications for very early mantle dynamics and the formation of very early mantle reservoirs.

  16. Mesocrystals luminescent BaZrHfO{sub 3} synthesized via hydrothermal process assisted by microwave

    Energy Technology Data Exchange (ETDEWEB)

    Fassbender, Rafael Uarth, E-mail: uarth.fisica@gmail.com

    2016-07-01

    Full text: The Barium Zirconate (BaZrO{sub 3}), is a ceramic oxide belonging to the functional group of perovskites (ABO{sub 3}), this compound can be doped with hafniun (Hf) in solid solution by microwave assisted hydrothermal method (MAH) radioluminescent increases their properties. This method allows to obtain barium zirconate at low temperature as 140 deg C and short times as 160 minutes. The choice of Hafnium (Hf) as a dopant is based on its similarity with Zirconium (Zr), another good reason for this choice is that the Hafnium has intrinsic luminescent characteristics. In general, radioluminescent materials have high density and high atomic mass (atomic number of Hafnium is 72), thereby facilitating the absorption of ionizing radiation to convert it into visible light, this characteristic is strongly dependent on the morphology and especially the electronic structure of (BaZrO{sub 3}). This work consisted in production of barium zirconate powders doped 1-2-4-8-16% (Hf) using (MAH) method. For the characterization of the powders was employed methods : a) X-ray diffraction, b) Raman Spectroscopy, c) Xanes, d) photoluminescence spectroscopy. After the electronic and structural characterization the powders were introduced in a polymeric resin (nylon-BZO), one new characterizations will be performed to validate the results obtained in the production of films to the results already obtained for the powders. We conclude so far, that the powders-doped with 16% Hf has an intense luminescent emission compared to the powders with less concentration of Hf. The small structural change that causes the Hf in (BZO) is considered as a secondary factory. (author)

  17. Interacciones hiperfinas en BaxSr1-xHfO3

    Directory of Open Access Journals (Sweden)

    López García, A.

    1999-10-01

    Full Text Available In order to determine the microscopic role of cation A in ABO3 perovskites the hyperfine interaction in the Sr1-xBaxHfO3 system using Perturbed Angular Correlation spectroscopy (PAC is studied. As a previous result the compositions x = 0.50 and 0.25 are shown. The PAC spectra were obtained in the temperature range from 20 to 1000ºC. In both compounds a phase transition to higher symmetry structure was observed at T≈400 and 200ºC, respectively. This structure is proposed to be cubic in both compositions. The results are compared with those obtained in SrHfO3 and BaHfO3.Con el fin de determinar el papel microscópico que juega el catión A en las perovskitas ABO3 se estudia la interacción hiperfina el sistema Sr1-xBaxHfO3 usando la espectroscopia Correlaciones Angulares Perturbadas (PAC en función de la temperatura y la composición. Como resultado previo se muestra en este trabajo, el estudio de las composiciones x = 0.5 y 0.75. Las medidas PAC se realizaron en el intervalo de temperaturas que va desde 20 a 1000ºC. Para x=0.50 y 0.75 se determinó una transición a una fase de mayor simetría a T≈400 y 200ºC, respectivamente. Se propone que esta fase de mayor simetría es cúbica en ambas composiciones. Los resultados obtenidos son comparados con los compuestos puros SrHfO3 y BaHfO3.

  18. Dynamic neural network modeling of HF radar current maps for forecasting oil spill trajectories

    International Nuclear Information System (INIS)

    Tissot, P.; Perez, J.; Kelly, F.J.; Bonner, J.; Michaud, P.

    2001-01-01

    This paper examined the concept of dynamic neural network (NN) modeling for short-term forecasts of coastal high-frequency (HF) radar current maps offshore of Galveston Texas. HF radar technology is emerging as a viable and affordable way to measure surface currents in real time and the number of users applying the technology is increasing. A 25 megahertz, two site, Seasonde HF radar system was used to map ocean and bay surface currents along the coast of Texas where wind and river discharge create complex and rapidly changing current patters that override the weaker tidal flow component. The HF radar system is particularly useful in this type of setting because its mobility makes it a good marine spill response tool that could provide hourly current maps. This capability helps improve deployment of response resources. In addition, the NN model recently developed by the Conrad Blucher Institute can be used to forecast water levels during storm events. Forecasted currents are based on time series of current vectors from HF radar plus wind speed, wind direction, and water levels, as well as tidal forecasts. The dynamic NN model was tested to evaluate its performance and the results were compared with a baseline model which assumes the currents do not change from the time of the forecast up to the forecasted time. The NN model showed improvements over the baseline model for forecasting time equal or greater than 3 hours, but the difference was relatively small. The test demonstrated the ability of the dynamic NN model to link meteorological forcing functions with HF radar current maps. Development of the dynamic NN modeling is still ongoing. 18 refs., 1 tab., 5 figs

  19. Very high latitude F-region irregularities observed by HF-radar backscatter

    International Nuclear Information System (INIS)

    Baker, K.B.; Greenwald, R.A.; Tsunoda, R.T.

    1983-01-01

    In February and March, 1982, a coherent scatter HF radar was operated from Cleary, Alaska to observe 7- to 15-m wavelength F-region plasma irregularities near the poleward edge of the auroral zone and in the polar cap. The radar operated for five days from February 25 to March 1 and produced approximately 700,000 Doppler spectra during that time. Of those nearly 700,000 spectra, approximately 10% showed backscattered power 3 dB or more above the noise level. A ray tracing technique using electron densities determined by the Chatanika incoherent scatter radar was used to predict locations where the HF waves were approximately normal to the magnetic field. If those locations were also to contain small scale electron density structure, then one would expect them to backscatter the HF waves. Several comparisons were made between predicted and observed locations of radiowave backscatter and excellent agreement was obtained. In addition, comparisons of the Doppler velocities observed by the coherent scatter HF radar and those observed by the Chatanika radar showed good agreement, suggesting that the plasma irregularities observed by the HF radar drift with the ambient plasma. In addition, average vector velocities calculated for the entire 5-day period show a flow pattern consistent with polar cap convection models. This again indicates that the irregularities drift with the plasma, as is predicted by a number of theories of F-region plasma irregularities. In the summer of 1983, the research program begun with those measurements will be continued with a steerable phased-array HF radar located at Goose Bay, Labrador, that will view the same ionospheric region as does the Sondre Stromfjord incoherent scatter radar

  20. Dosimetry of ultraviolet radiation with BaHfO{sub 3} powders; Dosimetria de radiacion ultravioleta con polvos de BaHfO{sub 3}

    Energy Technology Data Exchange (ETDEWEB)

    Barrera A, A. A.; Aguilar D, G. A.; Guzman M, J.; Rivera M, T. [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Av. Legaria 694, Col. Irrigacion, 11500 Ciudad de Mexico (Mexico); Ceron R, V., E-mail: abalba1@hotmail.com [Universidad de Guanajuato, 37670 Leon, Guanajuato (Mexico)

    2016-10-15

    Ceramic materials based on pure barium hafnate (BaHfO{sub 3}) have been obtained as a powder by the co-precipitation method. The powders obtained have a cubic structure that favors the thermoluminescent and optical properties, through which a better detection of the non-ionizing radiation is allowed. With these powders various tests were performed in the ultraviolet range at different exposure times. These thermoluminescent (Tl) studies were carried out using a Tl 3500 hand held reader which yielded a brightness curve that ranged from room temperature to the 350 degrees Celsius. This BaHfO{sub 3} response exhibits a broad brightness curve with a single peak centered around 225 degrees Celsius. Finally, is reported that there are materials of barium hafnate (BaHfO{sub 3}) doped with some rare earths (Eu, Tb) which, instead of improving the performance of the powders, decrease it, so that the use of intrinsic barium hafnate is the most appropriate. (Author)

  1. Tunneling current in HfO2 and Hf0.5Zr0.5O2-based ferroelectric tunnel junction

    Science.gov (United States)

    Dong, Zhipeng; Cao, Xi; Wu, Tong; Guo, Jing

    2018-03-01

    Ferroelectric tunnel junctions (FTJs) have been intensively explored for future low power data storage and information processing applications. Among various ferroelectric (FE) materials studied, HfO2 and H0.5Zr0.5O2 (HZO) have the advantage of CMOS process compatibility. The validity of the simple effective mass approximation, for describing the tunneling process in these materials, is examined by computing the complex band structure from ab initio simulations. The results show that the simple effective mass approximation is insufficient to describe the tunneling current in HfO2 and HZO materials, and quantitative accurate descriptions of the complex band structures are indispensable for calculation of the tunneling current. A compact k . p Hamiltonian is parameterized to and validated by ab initio complex band structures, which provides a method for efficiently and accurately computing the tunneling current in HfO2 and HZO. The device characteristics of a metal/FE/metal structure and a metal/FE/semiconductor (M-F-S) structure are investigated by using the non-equilibrium Green's function formalism with the parameterized effective Hamiltonian. The result shows that the M-F-S structure offers a larger resistance window due to an extra barrier in the semiconductor region at off-state. A FTJ utilizing M-F-S structure is beneficial for memory design.

  2. Vacancy induced metallicity at the CaHfO3/SrTiO3 interface

    KAUST Repository

    Nazir, Safdar; Pulikkotil, J. J.; Schwingenschlö gl, Udo; Singh, Nirpendra

    2011-01-01

    Density functional theory is used to study the electronic properties of the oxide heterointerfaceCaHfO3/SrTiO3. Structural relaxation is carried out with and without O vacancies. As compared to related interfaces, strongly reduced octahedral distortions are found. Stoichiometric interfaces between the wide band gap insulatorsCaHfO3 and SrTiO3 turn out to exhibit an insulating state. However, interface metallicity is introduced by O vacancies, in agreement with experiment. The reduced octahedral distortions and necessity of O deficiency indicate a less complicated mechanism for the creation of the interfacial electron gas.

  3. Vacancy induced metallicity at the CaHfO3/SrTiO3 interface

    KAUST Repository

    Nazir, Safdar

    2011-03-31

    Density functional theory is used to study the electronic properties of the oxide heterointerfaceCaHfO3/SrTiO3. Structural relaxation is carried out with and without O vacancies. As compared to related interfaces, strongly reduced octahedral distortions are found. Stoichiometric interfaces between the wide band gap insulatorsCaHfO3 and SrTiO3 turn out to exhibit an insulating state. However, interface metallicity is introduced by O vacancies, in agreement with experiment. The reduced octahedral distortions and necessity of O deficiency indicate a less complicated mechanism for the creation of the interfacial electron gas.

  4. Self-organization as the cause of different states of dc and hf discharge plasmas

    International Nuclear Information System (INIS)

    Lozneanu, E.; Dimitriu, D.; Gaman, C.; Furtuna, C.; Filep, E.; Sanduloviciu, M.

    2004-01-01

    Dc and hf gas discharges used in industrial devices are strongly nonlinear media whose characteristics and behavior critically depend on the type of the device and on the way and the amount of energy injected into the system. Consequently, considering a certain industrial device, it is possible to select, by gradually changing the injected energy, the working regimes that offer the most suitable conditions for a certain practical applications. The consideration of the nonlinear behavior of gaseous conductors (plasmas), created in dc and hf electric fields, and implicitly of the self-organizing phenomena at their origin become important for certain applications (Authors)

  5. On the stabilization of gas discharge by an hf-electric field

    International Nuclear Information System (INIS)

    Rakhimova, T.V.; Rakhimov, A.T.

    1975-01-01

    It is shown that when the bulk gas discharge is placed in an hf-electric field of sufficiently high frequency in the process of gas discharge burning there appears a long phase during which the gas ionization is inessential and the discharge burns in a recombining plasma. Such a stage may affect the stability of a gas discharge. It is shown also that at comparable values of intensities of the d.c. and hf electric fields there is a small parameter for the weakly-ionized plasma in which the relative portion of energy introduced into the discharge during the stage of gas ionization may be sufficiently small. (Auth.)

  6. Mixed Messages from Garnet Lu-Hf and Sm-Nd Geochronology

    Science.gov (United States)

    Vervoort, J. D.; Wang, D.; Johnson, T. A.

    2017-12-01

    Garnet geochronology provides important information on the timing and conditions of metamorphism. As a major indicator mineral formed during metamorphism, its direct dating can not only help establish the timing of metamorphism, provide the "t" for P-T-t paths, but also, if the dated garnet can be placed in a textural context, can provide information on the timing of deformational features. With advances in chemistry and mass spectrometry, garnet Lu-Hf and Sm-Nd geochronology has become an important geochronological tool and we can now reliably (if not routinely) date a wide variety of garnet compositions formed under diverse conditions. In the course of dating a variety of lithologies using both Lu-Hf and Sm-Nd isotope systems, however, some intriguing results have emerged. Although there are many examples where the Lu-Hf and Sm-Nd systems give the same date within uncertainty, there are also many cases where these systems yield significantly different dates, and the differences between these dates can be considerable—many 10's of Ma of and even 100's of Ma. For example, in garnet-bearing Mesoproterozoic gneisses from across the Blue Ridge Province in Virginia, both Lu-Hf and Sm-Nd analyses (determined on the same solutions) define narrow time spans, but with the Sm-Nd dates systematically younger (for orthogneisses Lu-Hf dates are 1032 to 1019 Ma whereas Sm-Nd dates are 965 to 949 Ma—a difference of 67 to 80 Ma). There are many other examples of systematically younger Sm-Nd garnet dates in both the literature and with our ongoing research. Potential explanations for these differences include: 1) strong partitioning of Lu into garnet during growth yielding ages weighted toward the beginning of growth; 2) faster Lu diffusion from high Lu regions after garnet formation, potentially leading to isochron rotation and anomalously old Lu-Hf dates; and 3) differences in closure temperatures of the two isotope systems. We will review several examples of divergent Lu-Hf

  7. Forecasts of geomagnetic activities and HF radio propagation conditions made at Hiraiso/Japan

    Science.gov (United States)

    Marubashi, K.; Miyamoto, Y.; Kidokoro, T.; Ishii, T.

    1979-01-01

    The Hiraiso Branch of RRL prediction techniques are summarized separately for the 27 day recurrent storm and the flare-associated storm. The storm predictions are compared with the actual geomagnetic activities in two ways. The first one is the comparison on a day to day basis. In the second comparison, the accuracy of the storm predictions during 1965-1976 are evaluated. In addition to the storm prediction, short-term predictions of HF radio propagation conditions are conducted at Hiraiso. The HF propagation predictions are briefly described as an example of the applications of the magnetic storm prediction.

  8. Magnetic dipole moments of High-K isomeric states in Hf isotopes

    CERN Multimedia

    Walters, W; Nishimura, K; Bingham, C R

    2007-01-01

    It is proposed to make precision measurements of the magnetic moments of 5 multi-quasi-particle K-isomers in Hf nuclei by the Nuclear Magnetic Resonance of Oriented Nuclei (NMR/ON) technique using the NICOLE on-line nuclear orientation facility and exploiting the unique HfF$_{3}$ beams recently available at ISOLDE. Results will be used to extract single-particle and collective g-factors of the isomeric states and their excitations and to shed new light on their structure.

  9. HF radar and drifter observing system in the Adriatic for fishery management and security

    DEFF Research Database (Denmark)

    Corgnati, Lorenzo; Carlson, Daniel Frazier; Mantovani, Carlo

    2014-01-01

    A HF radar system has been operating since May 2013 in the Southern Adriatic between the Gargano Cape and the Manfredonia Gulf. The system, that has been tested and complemented with drifter launchings during three experiments, produces maps of surface ocean velocities at 2 km resolution every hour....... These data support fishery management as well as search and rescue and pollution mitigation operations. The Manfredonia Gulf is a known nursery area for small pelagic fish (anchovies and sardines), and its dynamics and connectivity properties are very relevant to the study of population dynamics. HF radar...

  10. 120 MeV Ag ion induced effects in Au/HfO2/Si MOSCAPs

    Science.gov (United States)

    Manikanthababu, N.; Prajna, K.; Pathak, A. P.; Rao, S. V. S. Nageswara

    2018-05-01

    HfO2/Si thinfilms were deposited by RF sputtering technique. 120 MeV Ag ion irradiation has been used to study the electrical properties of Au/HfO2/Si MOSCAPs. SHI (120 MeV Ag) induced annealing, defects creation and intermixing effects on the electrical properties of these systems have been studied. Here, we have observed that the high electronic excitation can cause a significant reduction of leakage currents in these MOSCAP devices. Various quantum mechanical tunneling phenomenon has been observed from the I-V characteristics.

  11. Saturated steams pressure of HfCl/sub 4/-KCl molten mixtures

    Energy Technology Data Exchange (ETDEWEB)

    Salyulev, A B; Smirnov, M V; Kudyakov, V Ya [AN SSSR, Sverdlovsk. Inst. Ehlektrokhimii

    1980-02-01

    A bellows null pressure gauge and the dynamic method were used to measure the total and partial pressures of saturated vapors of individual components of molten HfCl/sub 4/-KCl mixtures, as a function of temperature (260 to 1000 deg C) and composition (1.9 to 64.3 mol.% HfCl/sub 4/). Empirical equations expressing the relationship between pressure and temperature are presented. It is shown that in molten mixtures of hafnium tetrachloride with chlorides of alkaline metals its partial pressure dramatically increases when potassium chloride substitutes for cesium chloride.

  12. Saturated steams pressure of HfCl4-KCl molten mixtures

    International Nuclear Information System (INIS)

    Salyulev, A.B.; Smirnov, M.V.; Kudyakov, V.Ya.

    1980-01-01

    A bellows null pressure gauge and the dynamic method were used to measure the total and partial pressures of saturated vapors of individual components of molten HfCl 4 -KCl mixtures, as a function of temperature (260 to 1000 deg C) and composition (1.9 to 64.3 mol.% HfCl 4 ). Empirical equations expressing the relationship between pressure and temperature are presented. It is shown that in molten mixtures of hafnium tetrachloride with chlorides of alkaline metals its partial pressure dramatically increases when potassium chloride substitutes for cesium chloride

  13. Complete tests of 2000 Hamamatsu R7525HA phototubes for the CMS-HF Forward Calorimeter

    International Nuclear Information System (INIS)

    Akgun, U.; Ayan, A.S.; Bruecken, P.; Duru, F.; Guelmez, E.; Mestvirishvilli, A.; Miller, M.; Olson, J.; Onel, Y.; Schmidt, I.

    2005-01-01

    Approximately 2000 PMTs will be used to detect the Cherenkov light generated in quartz fibers embedded in the CMS-HF Forward Calorimeter. The Hamamatsu R7525HA PMT was chosen for this purpose. We measured the transit time, transit time spread, pulse width, rise time, anode dark current, and relative gain for each tube in the test station at University of Iowa. Life-time, gain versus high voltage, and single photoelectron spectrum measurements were also done on a small sample of PMTs. All the tubes were tested to verify that they conform to the HF requirements

  14. Um estudo teórico de propriedades moleculares em complexos de hidrogênio trimoleculares C2H4···2HF, C2H2···2HF e C3h6···2HF A theoretical study of molecular properties of C2H4···2HF, C2H2···2HF AND C3H6···2HF trimolecular hydrogen-bonded complexes

    Directory of Open Access Journals (Sweden)

    Boaz G. Oliveira

    2008-01-01

    Full Text Available We present a theoretical study of molecular properties in C2H4···2HF, C2H2···2HF and C3H6···2HF trimolecular hydrogen-bonded complexes. From B3LYP/6-311++G(d,p calculations, the most important structural deformations are related to the C=C (C2H4, C≡C (C2H2, C-C (C3H6 and HF bond lengths. According to the Bader's atoms in molecules and CHELPG calculations, it was identified a tertiary interaction between the fluorine atom of the second hydrofluoric acid molecule and hydrogen atoms of the ethylene and acetylene within the C2H4···2HF and C2H2···2HF complexes, respectively. Additionally, the evaluation of the infrared spectrum characterized the new vibrational modes and bathochromic effect of the HF molecules.

  15. Revisiting Hansen Solubility Parameters by Including Thermodynamics

    NARCIS (Netherlands)

    Louwerse, Manuel J; Fernández-Maldonado, Ana María; Rousseau, Simon; Moreau-Masselon, Chloe; Roux, Bernard; Rothenberg, Gadi

    2017-01-01

    The Hansen solubility parameter approach is revisited by implementing the thermodynamics of dissolution and mixing. Hansen's pragmatic approach has earned its spurs in predicting solvents for polymer solutions, but for molecular solutes improvements are needed. By going into the details of entropy

  16. Solubility of hydrogen in delta iron

    International Nuclear Information System (INIS)

    Shapovalov, V.I.; Trofimenko, V.V.

    1979-01-01

    The solubility of hydrogen in iron (less than 0.002 % impurities) at temperatures of 800-1510 deg C and a pressure of 100 atm was measured. The heat of solution of hydrogen in delta-Fe, equal to 73 kJ/g-atom, is by far greater than the corresponding values for α- and γ-Fe

  17. Solubility of ethylene in methyl propionate

    NARCIS (Netherlands)

    Shariati - Sarabi, A.; Florusse, L.J.; Peters, C.J.

    2015-01-01

    In this work, the solubility of ethylene in methyl propionate was measured within a temperature range of 283.5–464.8 K and pressures up to 10.7 MPa. Experiments were carried out using the Cailletet apparatus, which uses a synthetic method for the experiments. The critical points of several isopleths

  18. Radiculography with water-soluble contraste medium

    International Nuclear Information System (INIS)

    Araujo Pinheiro, R.S. de

    1987-01-01

    The etiologic diagnosis of the lumbar pain is discussed. The radiculography with water-soluble contrast medium is used and 250 cases are studied. Some practical criteria of indication executation and interpretation of the examination are reported. (M.A.C.) [pt

  19. Solubility of heavy metals added to MSW

    International Nuclear Information System (INIS)

    Lo, H.M.; Lin, K.C.; Liu, M.H.; Pai, T.Z.; Lin, C.Y.; Liu, W.F.; Fang, G.C.; Lu, C.; Chiang, C.F.; Wang, S.C.; Chen, P.H.; Chen, J.K.; Chiu, H.Y.; Wu, K.C.

    2009-01-01

    This paper aims to investigate the six heavy metal levels (Cd, Cr, Cu, Pb, Ni and Zn) in municipal solid waste (MSW) at different pHs. It intends to provide the baseline information of metals solubility in MSW co-disposed or co-digested with MSW incinerator ashes in landfill or anaerobic bioreactors or heavy metals contaminated in anaerobic digesters. One milliliter (equal to 1 mg) of each metal was added to the 100 ml MSW and the batch reactor test was carried out. The results showed that higher HNO 3 and NaOH were consumed at extreme pH of 1 and 13 compared to those from pH 2 to 11 due to the comparably higher buffer capacity. Pb was found to have the least soluble level, highest metal adsorption (%) and highest partitioning K d (l g -1 ) between pH 3 and 12. In contrast, Ni showed the highest soluble level, lowest metal adsorption (%) and lowest K d (l g -1 ) between pH 4 and 12. Except Ni and Cr, other four metals seemed to show the amphibious properties as comparative higher solubility was found in the acidic and basic conditions

  20. Solubility of heavy metals added to MSW

    Energy Technology Data Exchange (ETDEWEB)

    Lo, H.M. [Department of Environmental Engineering and Management, Chaoyang University of Technology, 168 Gifong E. Road, Wufong, Taichung County 41349, Taiwan (China)], E-mail: hmlo@cyut.edu.tw; Lin, K.C. [Department of Occupational Safety and Health, Chung Shan Medical University, 110, Sec. 1, Jiangguo N. Rd., Taichung 402, Taiwan (China); Liu, M.H.; Pai, T.Z. [Department of Environmental Engineering and Management, Chaoyang University of Technology, 168 Gifong E. Road, Wufong, Taichung County 41349, Taiwan (China); Lin, C.Y. [Department of Soil and Water Conservation, Chung Hsing University, 250 Kuokuang Road, Taichung 402, Taiwan (China); Liu, W.F. [Department of Electronical Engineering, Feng Chia University, 100 Wenhwa Road, Taichung 407, Taiwan (China); Fang, G.C. [Department of Environmental Engineering, Hungkuang University, 34 Chung-Chie Road, Sha Lu, Taichung 433, Taiwan (China); Lu, C. [Department of Environmental Engineering, Chung Hsing University, 250 Kuokuang Road, Taichung 402, Taiwan (China); Chiang, C.F. [Department of Health Risk Management, China Medical University, No. 91 Hsueh-Shih Road, Taichung 40402, Taiwan (China); Wang, S.C.; Chen, P.H.; Chen, J.K.; Chiu, H.Y.; Wu, K.C. [Department of Environmental Engineering and Management, Chaoyang University of Technology, 168 Gifong E. Road, Wufong, Taichung County 41349, Taiwan (China)

    2009-01-15

    This paper aims to investigate the six heavy metal levels (Cd, Cr, Cu, Pb, Ni and Zn) in municipal solid waste (MSW) at different pHs. It intends to provide the baseline information of metals solubility in MSW co-disposed or co-digested with MSW incinerator ashes in landfill or anaerobic bioreactors or heavy metals contaminated in anaerobic digesters. One milliliter (equal to 1 mg) of each metal was added to the 100 ml MSW and the batch reactor test was carried out. The results showed that higher HNO{sub 3} and NaOH were consumed at extreme pH of 1 and 13 compared to those from pH 2 to 11 due to the comparably higher buffer capacity. Pb was found to have the least soluble level, highest metal adsorption (%) and highest partitioning K{sub d} (l g{sup -1}) between pH 3 and 12. In contrast, Ni showed the highest soluble level, lowest metal adsorption (%) and lowest K{sub d} (l g{sup -1}) between pH 4 and 12. Except Ni and Cr, other four metals seemed to show the amphibious properties as comparative higher solubility was found in the acidic and basic conditions.