Determination of heavy water in heavy water - light water mixtures

International Nuclear Information System (INIS)

Sanhueza M, A.

1986-01-01

A description about experimental methodology to determine isotopic composition of heavy water - light water mixtures is presented. The employed methods are Nuclear Magnetic Resonance Spectroscopy, for measuring heavy water concentrations from 0 to 100% with intervals of 10% approx., and mass Spectrometry, for measuring heavy water concentrations from 0.1 to 1% with intervals of 0.15% approx., by means of an indirect method of Dilution. (Author)

Development of a purification system at Dhruva to treat oil contaminated and chemically impure heavy water

International Nuclear Information System (INIS)

Suttraway, S.K.; Mishra, V.; Bitla, S.V.; Ghosh, S.K.

2006-01-01

Dhruva, a 100 MW (thermal) Research reactor uses Heavy Water as moderator, reflector and coolant. Normally during plant operation, the Heavy water from the system gets removed during operational and maintenance activities and this collected heavy water gets degraded and contaminated in the process. The degraded heavy water meeting the chemical specification requirement of the up gradation plant is sent for up gradation. Part of the Heavy water collected is contaminated with various organic and inorganic impurities and therefore cannot be sent for IP up gradation as it does not meet the chemical specification of the up gradation plant. This contaminated Heavy water was being stored in SS drums. Over the years of Reactor operation reasonable amount of contaminated Heavy water got collected in the plant. This Heavy water collected from leakages, during routine maintenance, operational activities and fuelling operation had tritium activity and variety of contamination including oil, chlorides, turbidity due to which the specific conductivity was very high. It was decided to purify this Heavy water in house to bring it up to up gradation plant chemical specification requirement. There were number of challenges in formulating a scheme to purify this Heavy water. The scheme needed to be simple and compact in design which could be set up in the plant itself. It should not pose radiological hazards due to radioactive Heavy water during its purification and handling. The contaminated Heavy water collected in drums had varying chemistry and IP. The purification plant should be able to do batch processing so that the different IP and chemical quality of Heavy water stored in different drums are not mixed during purification. It should be capable of removing the oil, chlorides, turbidity and decrease the conductivity to acceptable limits of the Up gradation plant. A purification plant was developed and commissioned after detail laboratory studies and trials. This paper explains

Heavy water upgrading system in the Fugen heavy water reactor

International Nuclear Information System (INIS)

Matsushita, T.; Susaki, S.

1980-01-01

The heavy water upgrading system, which is installed in the Fugen heavy water reactor (HWR) was designed to reuse degraded heavy water generated from the deuteration-dedeuteration of resin in the ion exchange column of the moderator purification system. The electrolysis method has been applied in this system on the basis of the predicted generation rate and concentration of degraded heavy water. The structural feature of the electrolytic cell is that it consists of dual cylindrical electrodes, instead of a diaphragm as in the case of conventional water electrolysis. 2 refs

Drying of heavy water system and works of charging heavy water in Fugen

International Nuclear Information System (INIS)

Matsushita, Tadashi; Iijima, Setsuo

1980-01-01

The advanced thermal reactor ''Fugen'' is the first heavy water-moderated, boiling light water-cooled nuclear reactor for power generation in Japan. It is a large heavy water reactor having about 130 m 3 of heavy water inventory and about 300 m 3 of helium space as the cover gas of the heavy water system. The heavy water required was purchased from FRG, which had been used for the power output test in the KKN, and the quality was 99.82 mol % mean heavy water concentration. The concentration of heavy water for Fugen used for the nuclear design is 99.70 mol%, and it was investigated how heavy water can be charged without lowering the concentration. The matters of investigation include the method of bringing the heavy water and helium system to perfect dryness after washing and light water test, the method of confirming the sufficient dryness to prevent the deterioration, and the method of charging heavy water safely from its containers. On the basis of the results of investigation, the actual works were started. The works of drying the heavy water and helium system by vacuum drying, the works of sampling heavy water and the result of the degree of deterioration, and the works of charging heavy water and the measures to the heavy water remaing in the containers are described. All the works were completed safely and smoothly. (J.P.N.)

Use of reflectors to enhance the synergistic effects of solar heating and solar wavelengths to disinfect drinking water sources.

Science.gov (United States)

Rijal, G K; Fujioka, R S

2003-01-01

Aluminum reflectors were added to solar units designed to inactivate faecal microorganisms (faecal coliform, E. coli, enterococci, FRNA coliphage, C. perfringens) in stream water and diluted sewage by the two mechanisms (solar heat, solar UV) known to inactivate microorganisms. During sunny conditions, solar units with and without reflectors inactivated E. coli to water standards. Solar units with reflectors disinfected the water sooner by increasing the water temperature by 8-10 degrees C to 64-75 degrees C. However, FRNA coliphages were still detected in these samples, indicating that this treatment may not inactivate pathogenic human enteric viruses. During cloudy conditions, reflectors only increased the water temperature by 3-4 degrees C to a maximum of 43-49 degrees C and E. coli was not completely inactivated. Under sunny and cloudy conditions, the UV wavelengths of sunlight worked synergistically with increasing water temperatures and were able to disinfect microorganisms at temperatures (45-56 degrees C), which were not effective in inactivating microorganisms. Relative resistance to the solar disinfecting effects were C. perfringens > FRNA coliphages > enterococci > E. coli > faecal coliform.

Deuterium and heavy water

International Nuclear Information System (INIS)

Vasaru, G.; Ursu, D.; Mihaila, A.; Szentgyorgyi, P.

1975-01-01

This bibliography on deuterium and heavy water contains 3763 references (1932-1974) from 43 sources of information. An author index and a subject index are given. The latter contains a list of 136 subjects, arranged in 13 main topics: abundance of deuterium , catalysts, catalytic exchange, chemical equilibria, chemical kinetics, deuterium and heavy water analysis, deuterium and heavy water properties, deuterium and heavy water separation, exchange reactions, general review, heavy water as moderator, isotope effects, synthesis of deuterium compounds

Use of reflectors to enhance the synergistic effects of solar heating and solar wavelengths to disinfect drinking water sources

Energy Technology Data Exchange (ETDEWEB)

Rijal, G.K. [Metropolitan Water Reclamation District of Greater Chicago, Cicero, Illinois (United States); Fujioka, R.S. [University of Hawaii, Honolulu (United States). Water Resources Research Center

2004-07-01

Aluminum reflectors were added to solar units designed to inactivate faecal microorganisms (faecal coliform, E. coli, enterococci, FRNA coliphage, C. perfringens) in stream water and diluted sewage by the two mechanisms (solar heat, solar UV) known to inactivate microorganisms. During sunny conditions, solar units with and without reflectors inactivated E. coli to <1 CFU/100 ml to meet drinking water standards. Solar units with reflectors disinfected to the water sooner by increasing the water temperature by 8-10{sup o}C to 64-75{sup o}C. However, FRNA coliphages were still detected in these samples, indicating that this treatment may not inactivate pathogenic human enteric viruses. During cloudy conditions, reflectors only increased the water temperature by 3-4{sup o}C to a maximum of 43-49{sup o}C and E. coli was not completely inactivated. Under sunny and cloudy conditions, the UV wavelengths of sunlight worked synergistically with increasing water temperatures and were able to disinfect microorganisms at temperatures (45-56{sup o}C), which were not effective in inactivating microorganisms. Relative resistance to the solar disinfecting effects were C perfringens > FRNA coliphages > enterococci >E. coli > faecal coliform. (author)

Heavy water upgrader of 'Fugen'

International Nuclear Information System (INIS)

Matsushita, Tadashi; Sasaki, Shigeo

1980-01-01

The nuclear power station of the advanced thermal prototype reactor ''Fugen'' has continued the smooth operation since it started the fullscale operation in March, 1979. Fugen is the first heavy water-moderated, boiling light water-cooled reactor in Japan, and its outstanding feature is the use of heavy water as the moderator. The quantity of heavy water retained in Fugen is about 140 m 3 , and the concentration is 99.8 wt.%. This heavy water had been made is USA, and was imported from F.R. of Germany where it had been used. Heavy water is an internationally regulated material, and it is very expensive and hard to purchase. Therefore in order to prevent the deterioration of heavy water and to avoid its loss as far as possible, the management of the quantity and the control of the water quality have been carried out carefully and strictly. The generation of deteriorated heavy water occurs from the exchange of ion exchange resin for poison removal and purification. The heavy water upgrader reconcentrates the deteriorated heavy water of high concentration and returns to the heavy water system, and it was installed for the purpose of reducing the purchase of supplementary heavy water. The outline of the heavy water upgrader, its construction, the performance test and the operation are described. (Kako, I.)

Water resistant rhodium plated reflectors for use in the DIRC BaBar Cherenkov detector

CERN Document Server

Benkebil, M; Plaszczynski, S; Schune, M H; Wormser, G

2000-01-01

Early simulation studies showed that reflectors mounted on the photomultipliers would be useful for the DIRC BaBar Cherenkov detector, showing a gain between 20% and 30% in the number of Cherenkov photons. The proof of principle for these reflectors has been obtained during the beam test of a large-scale prototype of the DIRC detector. An extensive R and D has been conducted in order to test different metallization procedures. Indeed, the challenge was to find a metallization technique which can resist the pure de-ionized water (>15 M OMEGA) up to 10 yr. The chosen technology was rhodium plated reflectors. During the first BaBar cosmic run, the measured performance confirmed the results of the simulation, the prototype-II and the R and D.

Lamp system with conditioned water coolant and diffuse reflector of polytetrafluorethylene(PTFE)

Science.gov (United States)

Zapata, Luis E.; Hackel, Lloyd

1999-01-01

A lamp system with a very soft high-intensity output is provided over a large area by water cooling a long-arc lamp inside a diffuse reflector of polytetrafluorethylene (PTFE) and titanium dioxide (TiO.sub.2) white pigment. The water is kept clean and pure by a one micron particulate filter and an activated charcoal/ultraviolet irradiation system that circulates and de-ionizes and biologically sterilizes the coolant water at all times, even when the long-arc lamp is off.

Heavy water and nonproliferation

International Nuclear Information System (INIS)

Miller, M.M.

1980-05-01

This report begins with a historical sketch of heavy water. The report next assesses the nonproliferation implications of the use of heavy water-moderated power reactors; several different reactor types are discussed, but the focus is on the natural uranium, on-power fueled, pressure tube reactor CANDU. The need for and development of on-power fueling safeguards is discussed. Also considered is the use of heavy water in plutonium production reactors as well as the broader issue of the relative nuclear leverage that suppliers can bring to bear on countries with natural uranium-fueled reactors as compared to those using enriched designs. The final chapter reviews heavy water production methods and analyzes the difficulties involved in implementing these on both a large and a small scale. It concludes with an overview of proprietary and nonproliferation constraints on heavy water technology transfer

Improvement in fuel utilization in pressurized heavy water reactors due to increased heavy water purity

International Nuclear Information System (INIS)

Balakrishnan, M.R.

1991-01-01

This paper reports that in a pressurized heavy water reactor (PHWR), the reactivity of the reactor and, consequently, the discharge burnup of the fuel depend on the isotopic purity of the heavy water used in the reactor. The optimal purity of heavy water used in PHWRs, in turn, depends on the cost of fabricated uranium fuel and on the incremental cost incurred in improving the heavy water purity. The physics and economics aspects of the desirability of increasing the heavy water purity in PHWRs in India were first examined in 1978. With the cost data available at that time, it was found that improving the heavy water purity from 99.80% to 99.95% was economically attractive. The same problem is reinvestigated with current cost data. Even now, there is sufficient incentive to improve the isotopic purity of heavy water used in PHWRs. Admittedly, the economic advantage that can be derived depends on the cost of the fabricated fuel. Nevertheless, irrespective of the economics, there is also a fairly substantial saving in natural uranium. That the increase in the heavy water purity is to be maintained only in the low-pressure moderator system, and not in the high-pressure coolant system, makes the option of achieving higher fuel burnup with higher heavy water purity feasible

Pulsed neutron intensity from rectangular shaped light water moderator with fast-neutron reflector

International Nuclear Information System (INIS)

Kiyanagi, Yoshiaki; Iwasa, Hirokatsu

1982-01-01

With a view to enhancing the thermal-neutron intensity obtained from a pulsed neutron source, an experimental study has been made to determine the optimum size of a rectangular shaped light water moderator provided with fast neutron reflector of beryllium oxide or graphite, and decoupled thermal-neutronically by means of Cd sheet. The optimum dimensions for the moderator are derived for the neutron emission surface and the thickn ess, for the cases in which the neutron-producing target is placed beneath the moderator (''wing geometry'') or immediately behind the moderator (''slab geometry''). The major conclusions drawn from the experimental results are as follows. The presence of the Cd decoupler inserted between the moderator and reflector prevent the enhancement of thermal-neutron emission time gained by the provision of reflector. With a graphite reflector about 14 cm thick, (a) the optimum area of emission surface would be 25 x 25 cm 2 for wing geometry and still larger for slab geometry, and (b) the optimum moderator thickness would be 5.5 cm for slab geometry and 8.5 cm for wing geometry. It is thus concluded that a higher neutron emission intensity can be obtained with slab than with wing geometry provided that a large emission surface can be adopted for the moderator. (author)

Production of heavy water

Science.gov (United States)

Spencer, Larry S.; Brown, Sam W.; Phillips, Michael R.

2017-06-06

Disclosed are methods and apparatuses for producing heavy water. In one embodiment, a catalyst is treated with high purity air or a mixture of gaseous nitrogen and oxygen with gaseous deuterium all together flowing over the catalyst to produce the heavy water. In an alternate embodiment, the deuterium is combusted to form the heavy water. In an alternate embodiment, gaseous deuterium and gaseous oxygen is flowed into a fuel cell to produce the heavy water. In various embodiments, the deuterium may be produced by a thermal decomposition and distillation process that involves heating solid lithium deuteride to form liquid lithium deuteride and then extracting the gaseous deuterium from the liquid lithium deuteride.

Neutron spectrum in small iron pile surrounded by lead reflector

International Nuclear Information System (INIS)

Kimura, Itsuro; Hayashi, S.A.; Kobayashi, Katsuhei; Matsumura, Tetsuo; Nishihara, Hiroshi.

1978-01-01

In order to save the quantity of sample material, a possibility to assess group constants of a reactor material through measurement and analysis of neutron spectrum in a small sample pile surrounded by a reflector of heavy moderator, was investigated. As the sample and the reflector, we chose iron and lead, respectively. Although the time dispersion in moderation of neutrons was considerably prolonged by the lead reflector, this hardly interferes with the assessment of group constants. Theoretical calculation revealed that both the neutron flux spectrum and the sensitivity coefficient of group constants in an iron sphere, 35 cm in diameter surrounded by the lead reflector, 25 cm thick, were close to those of the bare iron sphere, 108 cm in diameter. The neutron spectra in a small iron pile surrounded by a lead reflector were experimentally obtained by the time-of-flight method with an electron linear accelerator and the result was compared with the predicted values. It could be confirmed that a small sample pile surrounded by a reflector, such as lead, was as useful as a much larger bulk pile for the assessment of group constants of a reactor material. (auth.)

Initial global 2-D shielding analysis for the Advanced Neutron Source core and reflector

Energy Technology Data Exchange (ETDEWEB)

Bucholz, J.A.

1995-08-01

This document describes the initial global 2-D shielding analyses for the Advanced Neutron Source (ANS) reactor, the D{sub 2}O reflector, the reflector vessel, and the first 200 mm of light water beyond the reflector vessel. Flux files generated here will later serve as source terms in subsequent shielding analyses. In addition to reporting fluxes and other data at key points of interest, a major objective of this report was to document how these analyses were performed, the phenomena that were included, and checks that were made to verify that these phenomena were properly modeled. In these shielding analyses, the fixed neutron source distribution in the core was based on the `lifetime-averaged` spatial power distribution. Secondary gamma production cross sections in the fuel were modified so as to account intrinsically for delayed fission gammas in the fuel as well as prompt fission gammas. In and near the fuel, this increased the low-energy gamma fluxes by 50 to 250%, but out near the reflector vessel, these same fluxes changed by only a few percent. Sensitivity studies with respect to mesh size were performed, and a new 2-D mesh distribution developed after some problems were discovered with respect to the use of numerous elongated mesh cells in the reflector. All of the shielding analyses were performed sing the ANSL-V 39n/44g coupled library with 25 thermal neutron groups in order to obtain a rigorous representation of the thermal neutron spectrum throughout the reflector. Because of upscatter in the heavy water, convergence was very slow. Ultimately, the fission cross section in the various materials had to be artificially modified in order to solve this fixed source problem as an eigenvalue problem and invoke the Vondy error-mode extrapolation technique which greatly accelerated convergence in the large 2-D RZ DORT analyses. While this was quite effective, 150 outer iterations (over energy) were still required.

Initial global 2-D shielding analysis for the Advanced Neutron Source core and reflector

International Nuclear Information System (INIS)

Bucholz, J.A.

1995-08-01

This document describes the initial global 2-D shielding analyses for the Advanced Neutron Source (ANS) reactor, the D 2 O reflector, the reflector vessel, and the first 200 mm of light water beyond the reflector vessel. Flux files generated here will later serve as source terms in subsequent shielding analyses. In addition to reporting fluxes and other data at key points of interest, a major objective of this report was to document how these analyses were performed, the phenomena that were included, and checks that were made to verify that these phenomena were properly modeled. In these shielding analyses, the fixed neutron source distribution in the core was based on the 'lifetime-averaged' spatial power distribution. Secondary gamma production cross sections in the fuel were modified so as to account intrinsically for delayed fission gammas in the fuel as well as prompt fission gammas. In and near the fuel, this increased the low-energy gamma fluxes by 50 to 250%, but out near the reflector vessel, these same fluxes changed by only a few percent. Sensitivity studies with respect to mesh size were performed, and a new 2-D mesh distribution developed after some problems were discovered with respect to the use of numerous elongated mesh cells in the reflector. All of the shielding analyses were performed sing the ANSL-V 39n/44g coupled library with 25 thermal neutron groups in order to obtain a rigorous representation of the thermal neutron spectrum throughout the reflector. Because of upscatter in the heavy water, convergence was very slow. Ultimately, the fission cross section in the various materials had to be artificially modified in order to solve this fixed source problem as an eigenvalue problem and invoke the Vondy error-mode extrapolation technique which greatly accelerated convergence in the large 2-D RZ DORT analyses. While this was quite effective, 150 outer iterations (over energy) were still required

Production of heavy water in India

International Nuclear Information System (INIS)

Deshpande, P.G.; Bimbhat, K.S.; Bhargava, R.K.

India's first heavy water plant, using electrolysis of water followed by liquid hydrogen distillation, has been operating in association with a fertilizer plant at Nangal since 1962. A dual-temperature process plant at Kota uses heat from the Rajasthan Atomic Power Station. The heavy water plants at Baroda and Tuticorin use ammonia-hydrogen exchange and are integrated with fertilizer ammonia plants. Choice of a particular process for heavy water production depends upon local conditions as well as the extent of the heavy water requirement

Multidimensional space-time kinetics of a heavy water moderated nuclear reactor

International Nuclear Information System (INIS)

Winn, W.G.; Baumann, N.P.; Jewell, C.E.

1980-01-01

Diffusion theory analysis of a series of multidimensional space-time experiments is appraised in terms of the final experiment of the series. In particular, TRIMHX diffusion calculations were examined for an experiment involving free-fall insertion of a 235 U-bearing rod into a heavy water moderated reactor with a large reflector. The experimental transient flux-tilts were accurately reproduced after cross section adjustments forced agreement between static diffusion calculations and static reactor measurements. The time-dependent features were particularly well modeled, and the bulk of the small discrepancies in space-dependent features should be removable by more refined cross-section adjustments. This experiment concludes a series of space-time experiments that span a wide range of delayed neutron holdback effects. TRIMHX calculations of these experiments demonstrate the accuracy of the modeling employed in the code

Pengaruh Pelat Penyerap Ganda Model Gelombang dengan Penambahan Reflector terhadap Kinerja Solar Water Heater Sederhana

OpenAIRE

Ismail, Nova Risdiyanto

2011-01-01

Telah banyak dilakukan USAha meningkatkan kinerja solar water heater diantaranya modifikasi pelat penyerap tunggal menjadi ganda, modifikasi aliran untuk meningkatkan penyerapan panas, modifikasi material dan pelat penyerap ganda model gelombang. Penelitian ini bertujuan untuk mengetahui pengaruh pelat penyerap ganda model gelombang dengan penambahan reflector terhadap kinerja solar water heater sederhana. Dalam penelitian ini dilakukan secara eksperimen, untuk embandingkan kinerja pelat pen...

Canadian heavy water production

International Nuclear Information System (INIS)

Dahlinger, A.; Lockerby, W.E.; Rae, H.K.

1977-05-01

The paper reviews Canadian experience in the production of heavy water, presents a long-term supply projection, relates this projection to the anticipated long-term electrical energy demand, and highlights principal areas for further improvement that form the bulk of our research and development program on heavy water processes

Power control device for heavy water moderated reactor

International Nuclear Information System (INIS)

Matsushima, Hidesuke; Masuda, Hiroyuki.

1978-01-01

Purpose: To improve self controllability of a nuclear power plant, as well as enable continuous power level control by a controlled flow of moderators in void pipes provided in a reactor core. Constitution: Hollow void pipes are provided in a reactor core to which a heavy water recycle loop for power control, a heavy water recycle pump for power control, a heavy water temperature regulator and a heavy water flow rate control valve for power control are connected in series to constitute a heavy water recycle loop for flowing heavy water moderators. The void ratio in each of the void pipes are calculated by a process computer to determine the flow rate and the temperature for the recycled heavy water. Based on the above calculation result, the heavy water temperature regulator is actuated by way of a temperature setter at the heavy water inlet and the heavy water flow rate is controlled by the actuation of the heavy water flow rate control valve. (Kawakami, Y.)

The variation of the reactivity with the number, diameter and length of the control rods in a heavy water natural uranium reactor

Energy Technology Data Exchange (ETDEWEB)

McCriric, H

1958-05-15

Starting with the known reactor constants for a heavy water moderated reactor with reflector and a given number of control rods of a certain size, the reactivity equivalence of the control rods is calculated. The calculation is given in detail. The number, length and diameter of the control rods is then varied and the effect of these parameters on the reactivity is shown graphically. Flux plots are also given for the reactor with and without control rods.

Comparative Experimental Analysis of the Thermal Performance of Evacuated Tube Solar Water Heater Systems With and Without a Mini-Compound Parabolic Concentrating (CPC Reflector(C < 1

Directory of Open Access Journals (Sweden)

Yuehong Su

2012-04-01

Full Text Available Evacuated tube solar water heater systems are widely used in China due to their high thermal efficiency, simple construction requirements, and low manufacturing costs. CPC evacuated tube solar water heaters with a geometrical concentration ratio C of less than one are rare. A comparison of the experimental rig of evacuated tube solar water heater systems with and without a mini-CPC reflector was set up, with a series of experiments done in Hefei (31°53'N, 117°15'E, China. The first and second laws of thermodynamics were used to analyze and contrast their thermal performance. The water in the tank was heated from 26.9 to 55, 65, 75, 85, and 95 °C. Two types of solar water heater systems were used, and the data gathered for two days were compared. The results show that when attaining low temperature water, the evacuated tube solar water heater system without a mini-CPC reflector has higher thermal and exergy efficiencies than the system with a mini-CPC reflector, including the average and immediate values. On the other hand, when attaining high temperature water, the system with a mini-CPC reflector has higher thermal and exergy efficiencies than the other one. The comparison presents the advantages of evacuated tube solar water heater systems with and without a mini-CPC reflector, which can be offered as a reference when choosing which solar water system to use for actual applications.

Efficiency improvement of flat plate solar collector using reflector

Directory of Open Access Journals (Sweden)

Himangshu Bhowmik

2017-11-01

Full Text Available Solar collectors are the main components of a solar heating system. The collectors collect the sun’s energy, transform this radiation into heat, and then transfer this heat into a fluid, water or air, which has many household or industrial applications. This paper introduces a new technology to improve the performance of the solar thermal collectors. The solar reflector used here with the solar collector to increase the reflectivity of the collector. Thus, the reflector concentrates both direct and diffuse radiation of the sun toward the collector. To maximize the intensity of incident radiation, the reflector was allowed to change its angle with daytime. The radiations coming from the sun’s energy were converted into heat, and then this heat was transferred to the collector fluid, water. A prototype of a solar water heating system was constructed and obtained the improvement of the collector efficiency around 10% by using the reflector. Thus, the present solar water heating systems having the best thermal performance compared to the available systems.

Heavy water moderated tubular type nuclear reactor

International Nuclear Information System (INIS)

Oohashi, Masahisa.

1986-01-01

Purpose: To enable to effectively change the volume of heavy water per unit fuel lattice in heavy water moderated pressure tube type nuclear reactors. Constitution: In a nuclear reactor in which fuels are charged within pressure tubes and coolants are caused to flow between the pressure tubes and the fuels, heavy water tubes for recycling heavy water are disposed to a gas region formed to the outside of the pressure tubes. Then, the pressure tube diameter at the central portion of the reactor core is made smaller than that at the periphery of the reactor core. Further, injection means for gas such as helium is disposed to the upper portion for each of the heavy water tubes so that the level of the heavy water can easily be adjusted by the control for the gas pressure. Furthermore, heavy water reflection tubes are disposed around the reactor core. In this constitution, since the pitch for the pressure tubes can be increased, the construction and the maintenance for the nuclear reactor can be facilitated. Also, since the liquid surface of the heavy water in the heavy water tubes can be varied, nuclear properties is improved and the conversion ratio is improved. (Ikeda, J.)

Method of controlling power of a heavy water reactor

International Nuclear Information System (INIS)

Masuda, Hiroyuki.

1975-01-01

Object: To adjust a level of heavy water in a region of reflection body to control power in a heavy water reactor. Structure: The interior of a core tank filled with heavy water is divided by a partition into a core heavy water region and a reflection body region formed by surrounding the core heavy water region, and a level of heavy water within the reflection body region is adjusted to control power. Preferably, it is desirable to communicate the core heavy water region with the reflection body heavy water region at their lower portion, and gas pressure applied to an upper portion within at least one of said regions is adjusted to adjust the level of heavy water within the reflection body heavy water region. Thereby, the heavy water within the reflection body heavy water region may be introduced into the core region, thus requiring no tank which stores heavy water within the reflection body region. (Kamimura, M.)

Measurement of concentration of heavy water

International Nuclear Information System (INIS)

Tsukamoto, Yuichi; Kondo, Mitsuo; Sakurai, Naoyuki

1979-01-01

The concentration of heavy water is measured as one of the technical management in the Fugen plant. The heavy water is used as the moderator in the reactor. The measuring method depends on the theory of light absorption. The light absorption range of heavy water spreads from near infrared to infrared zone. The near infrared absorption was adopted for the purpose, as the absorption is much larger in infrared zone, and the measurement has to be conducted, limiting the apparent absorption. This measuring method is available to determine the concentration of heavy water in the broad range exactly. The preparation of heavy water sample and the measurement of the absorption spectra of near infrared ray are explained, as the experimental procedure. The sample cell was made of quartz, and the spectroscope was the Hitachi 323 type. The resolving power is 100 nm and 27 nm for the wave length of 1000 nm and 2500 nm, respectively. Concerning the measured results, the absorption was recorded in the wave length range from 600 nm to 2600 nm, and for the heavy water concentration range from 0 to 99.77 wt. %. The peaks of absorption were located at the wave length of 1450, 1660, 1920, 1970, 2020 and 2600 nm. The three kinds of fundamental vibration mode of the molecules of both light and heavy water are shown, and the peaks belong to H 2 O, HDO and D 2 O, respectively. The relation between the absorption and the heavy water concentration, and that between the transmissivity and the wave length are shown, when the cell thickness was varied to 5 mm and 20 mm, and the heavy water concentration to 21%, 62% and 99.85%. (Nakai, Y.)

Water chemistry features of advanced heavy water reactor

International Nuclear Information System (INIS)

Sriram, Jayasree; Vijayan, K.; Kain, Vivekanad; Velmurugan, S.

2015-01-01

Advanced Heavy Water Reactor (AHWR) being designed in India proposes to use Plutonium and Thorium as fuel. The objective is to extract energy from the uranium-233 formed from Thorium. It is a heavy water moderated and light water cooled tube type boiling water reactor. It is a heavy water moderated and light water cooled tube type boiling water reactor. It is a natural circulation reactor. Thus, it has got several advanced passive safety features built into the system. The various water coolant systems are listed below. i) Main Heat transport System ii) Feed water system iii) Condenser cooling system iv) Process water system and safety systems. As it is a tube type reactor, the radiolysis control differs from the normal boiling water reactor. The coolant enters the bottom of the coolant channel, boiling takes place and then the entire steam water mixture exits the core through the long tail pipes and reaches the moisture separator. Thus, there is a need to devise methods to protect the tail pipes from oxidizing water chemistry condition. Similarly, the moderator heavy water coolant chemistry differs from that of moderator system chemistry of PHWR. The reactivity worth per ppm of gadolinium and boron are low in comparison to PHWR. As a result, much higher concentration of neutron poison has to be added for planned shutdown, start up and for actuating SDS-2. The addition of higher concentration of neutron poison result in higher radiolytic production of deuterium and oxygen. Their recombination back to heavy water has to take into account the higher production of these gases. This paper also discusses the chemistry features of safety systems of AHWR. In addition, the presentation will cover the chemistry monitoring methodology to be implemented in AHWR. (author)

Study of the heavy water regeneration processes

International Nuclear Information System (INIS)

Cavcic, E.

1965-11-01

Experience derived from heavy water reactor operation showed degradation and dilution of heavy water to be inevitable and depends on the type of reactor. Dilution of heavy water during operation of the RA and the RB reactors is shown in this report. Principles and procedures of heavy water regeneration by electrolysis, fractional distillation, cleaning, prevention of tritium contamination are described as well as separation columns

Heavy Water - Industrial Separation Processes

International Nuclear Information System (INIS)

Peculea, M.

1984-01-01

This monograph devoted to the heavy water production mainly presents the Romanian experience in the field which started in early sixties from the laboratory scale production and reached now the level of large scale industrial production at ROMAG-Drobeta, Romania. The book is structured in eleven chapters entitled: Overview, The main physical properties, Sources, Uses, Separation factor and equilibrium constant, Mathematical modelling of the separation process, Thermodynamical considerations on the isotope separation, Selection criteria for heavy water separation processes, Industrial installations for heavy water production, Prospects, Acknowledgements. 200 Figs., 90 Tabs., 135 Refs

Fast neutron flux in heavy water reactors; Flux de neutrons rapides dans les piles a eau lourde

Energy Technology Data Exchange (ETDEWEB)

Brisbois, J; Katz, S [Commissariat a l' Energie Atomique, Centre d' Etudes Nucleaires de Fontenay-aux-Roses, 92 (France)

1966-07-01

The possibility of calculating the fast neutron flux in a natural uranium-heavy water lattice by superposition of the individual contributions of the different fuel elements was verified using a one-dimension Monte-Carlo code. The results obtained are in good agreement with experimental measurements done in the core and reflector of the reactor AQUILON. (author) [French] La possibilite de calculer le flux de neutrons rapides dans un reseau d'uranium naturel a eau lourde par superposition des apports des divers barreaux, a ete verifiee en utilisant un code Monte-Carlo monodimensionel. Les resultats obtenus concordent avec des mesures experimentales effectuees dans le coeur et reacteur de la pile Aquilon. (auteurs)

Detection of gaseous heavy water leakage points in CANDU 6 pressurized heavy water reactors

International Nuclear Information System (INIS)

Park, T-K.; Jung, S-H.

1996-01-01

During reactor operation, the heavy water filled primary coolant system in a CANDU 6 Pressurized Heavy Water (PHWR) may leak through routine operations of the plant via components, mechanical joints, and during inadvertent operations etc. Early detection of leak points is therefore important to maintain plant safety and economy. There are many independent systems to monitor and recover heavy water leakage in a CANDU 6 PHWR. Methodology for early detection based on operating experience from these systems, is investigated in this paper. In addition, the four symptoms of D 2 O leakage, the associated process for clarifying and verifying the leakage, and the probable points of leakage are discussed. (author)

The effects of stainless steel radial reflector on core reactivity for small modular reactor

Energy Technology Data Exchange (ETDEWEB)

Kang, Jung Kil, E-mail: jkkang@email.kings.ac.kr; Hah, Chang Joo, E-mail: changhah@kings.ac.kr [KINGS, 658-91, Haemaji-ro, Seosaeng-myeon, Ulju-gun, Ulsan, 689-882 (Korea, Republic of); Cho, Sung Ju, E-mail: sungju@knfc.co.kr; Seong, Ki Bong, E-mail: kbseong@knfc.co.kr [KNFC, Daedeok-daero 989beon-gil, Yuseong-gu, Daejeon, 305-353 (Korea, Republic of)

2016-01-22

Commercial PWR core is surrounded by a radial reflector, which consists of a baffle and water. Radial reflector is designed to reflect neutron back into the core region to improve the neutron efficiency of the reactor and to protect the reactor vessels from the embrittling effects caused by irradiation during power operation. Reflector also helps to flatten the neutron flux and power distributions in the reactor core. The conceptual nuclear design for boron-free small modular reactor (SMR) under development in Korea requires to have the cycle length of 4∼5 years, rated power of 180 MWth and enrichment less than 5 w/o. The aim of this paper is to analyze the effects of stainless steel radial reflector on the performance of the SMR using UO{sub 2} fuels. Three types of reflectors such as water, water/stainless steel 304 mixture and stainless steel 304 are selected to investigate the effect on core reactivity. Additionally, the thickness of stainless steel and double layer reflector type are also investigated. CASMO-4/SIMULATE-3 code system is used for this analysis. The results of analysis show that single layer stainless steel reflector is the most efficient reflector.

Determining the asymptotic buckling for the reference RB reactor lattice

International Nuclear Information System (INIS)

Martinc, R.; Sotic, O.

1969-01-01

Material buckling was measured for reference lattice of the heavy water reflected system with 2% enriched uranium fuel. Experiments were done for cores with lattice pitch values: 8, 8√2, i 16 cm. Each of these cores had heavy water reflector, as well as active reflector - heavy water lattice with natural uranium fuel. The core was reflected by natural uranium lattice in order to approach asymptotic regime in the central zone. Buckling values obtained with the natural uranium lattice as reflector are, as a rule, lower then in case of heavy water reflector [sr

Finishing and upgrading of heavy water

International Nuclear Information System (INIS)

Butler, J.P.; Hammerli, M.

1981-01-01

This invention provides a process and apparatus for deuterium enrichment as a final stage in a heavy water plant, for continuous on-line enrichment of the heavy water in moderator and heat transfer systems in heavy water nuclear reactors, and for enrichment of hevy water that has been downgraded with natural water during the course of operating a heavy water nuclear reactor. The method comprises contacting partially-enriched heavy water feed in a catalyst column with hydrogen gas (essentially D 2 ) orginating in an electrolysis cell so as to enrich the feed water with deuterium extracted from the electrolytic hydrogen gas and passing the deuterium-enriched water to the electrolysis cell. The apparatus comprises a catalyst isotope exchange column with hydrogen gas and liquid water passing through in countercurrent isotope exchange, an electrolysis cell, a dehumidifer-scrubber; and means for passing the liquid water enriched in deuterium from the catalyst column through the dehumidifer-scrubber to the electrolysis cell, for passing the hydrogen gas evolved in the cathode side of the cell through the dehumidifier-scrubber to the catalyst column, for passing the hydrogen gas from the catalyst column to an output, for introducing an input water feed to the upper portion of the catalyst column, and for taking a product enriched in deuterium from the system. (LL)

Improvement of a measurement method of purified flows in a reflector of HANARO by an ultra-sonic flowmeter

International Nuclear Information System (INIS)

Choi, Young-San; Bae, Sang-Hoon; Kang, In-Hyuk; Lee, Yong-Sub; Jung, Hoan-Sung

2007-01-01

Heavy water is used in the reflector system in HANARO and the flow in the system is measured by a flowmeter and indicated in a control room. The Turbine Flowmeter to measure the purified flow, which had been used from the start up of reactor was broken down in the end of 2001. In order to avoid the exposure of tritium generated from heavy water leaked during a replacement, instead of fixing the flowmeter, an ultrasonic flowmeter was selected and installed and has been used to measure the flow. This paper describes the measurement principles, issues and calibration errors of the turbine flowmeter that was broken down. Also, it explains in detail the measurement principles of the ultrasonic flowmeter, the results of its field test and the results of its periodic tests for five years after the installation

Calculation of neutron flux distribution of thermal neutrons from microtron converter in a graphite moderator with water reflector

International Nuclear Information System (INIS)

Andrejsek, K.

1977-01-01

The calculation is made of the thermal neutron flux in the moderator and reflector by solving the neutron diffusion equation using the four-group theory. The correction for neutron absorption in the moderator was carried out using the perturbation theory. The calculation was carried out for four groups with the following energy ranges: the first group 2 MeV to 3 keV, the second group 3 keV to 5 eV, the third group 5 eV to 0.025 eV and the fourth group 0.025 eV. The values of the macroscopic cross section of capture and scattering, of the diffusion coefficient, the macroscopic cross section of the moderator, of the neutron age and the extrapolation length for the water-graphite moderator used in the calculations are given. The spatial distribution of the thermal neutron flux is graphically represented for graphite of a 30, 40, and 50 cm radius and for graphite of a 30 and 40 cm radius with a 10 cm water reflector; a graphic comparison is made of the distribution of the thermal neutron flux in water and in graphite, both 40 cm in radius. The system of graphite with reflector proved to be the best and most efficient system for raising the flux density of thermal neutrons. (J.P.)

Experimental verification of reflector savings calculated by REDIR code using two-group method; Eksperimentalna provera dvogrupnog racunanja reflektorske ustede koriscenog u REDIR-u

Energy Technology Data Exchange (ETDEWEB)

Sotic, O; Martinc, R [Boris Kidric Institute of nuclear sciences Vinca, Belgrade (Yugoslavia)

1968-12-15

Radial buckling and reflector savings for heavy water reactor with 2% enriched uranium fuel were measured and calculated by the REDIR code. A comparison of the obtained values is presented in this paper dependent on the reactor lattice pitch and reflector thickness. Experimental results obtained for lattice pitch of 16 cm prove the validity of applying the REDIR code for power reactors. U radu je dato uporedjenje izmedju izmerenih i teorijski izracunatih vrednosti (prema programu REDIR) radijalnih baklinga i reflektorske ustede za teskovodni reaktorski sistem sa 2% obogacenim uranskim gorivom u zavisnosti od koraka resetke i debljine reflektora. Rezultati dobijeni eksperimentima pri koraku resetke od 16 cm potvdjuju ispravnost primene programa REDIR za energetske reaktore. (author)

Heavy water at Aswan

International Nuclear Information System (INIS)

1959-01-01

A fertilizer factory is being built by Egyptian Chemical Industries (Kima) at Aswan on the upper Nile; it will produce a mixture of ammonium nitrate and calcium carbonate adjusted to contain 20.5% nitrogen. It is also proposed to construct a heavy water plant to be located at and integrated with the fertilizer factory. At the request of the Government of the United Arab Republic, the International Atomic Energy Agency sent an expert to carry out investigation of the technical, economic and other related aspects of the proposed production of heavy water. A report was submitted to the IAEA Director General. Its main conclusions can be summarized as follows: (1) Production of heavy water as a by-product of fertilizer manufacture at Aswan is technically feasible. Separation of deuterium from industrial hydrogen for this purpose could be done either by catalytic exchange or by liquefaction and distillation; the choice should depend on economic considerations. (2) The heavy water produced at Aswan should be competitive in cost with that produced elsewhere; this, however, would depend on whether firm contracts are obtained for the delivery of equipment at guaranteed prices and with guaranteed performance, and whether such prices are in reasonable agreement with preliminary estimates. (3) The future market for heavy water is difficult to predict. For one thing, there is a very large production capacity in the USA, most of which is idle due to lack of demand. Secondly, there is a relatively small production outside the USA that is sold at prices higher than that charged by the US Government. The future of the market is necessarily contingent upon the possibility of future free sale by the US Government. At the end of his report, the expert has also given his comments on possible further assistance to the project by IAEA

Indian heavy water programme - challenges and opportunities

International Nuclear Information System (INIS)

Aruldoss Kanthiah, W.S.

2010-01-01

Discovery of fission of uranium in 1939 opened up hitherto unknown possibilities for utilising the fission energy for use of mankind, mainly for the production of and electrical energy. It was realised that this nuclear energy could be an ideal substitute for the fast depleting fossil fuels which would one day get exhausted. Two main concepts of nuclear power reactor got evolved, one enriched uranium fuelled, ordinary water moderated reactor and another natural uranium fuelled heavy water moderated reactor. The concentration of uranium 235 U needed for ordinary water moderated reactors is 3% but the naturally occurring uranium in India contains only 0.7% of 235 U. The reactors utilising natural uranium as fuel require Heavy Water as moderator. The processing of uranium ore to achieve from 0.7% to 3% is highly complex. Recognising the fact that India has limited uranium resources but rich thorium resources, Dr. Bhabha formulated a three stage nuclear power generation programme for our country. The first generation reactors can use natural uranium as fuel with heavy water as moderator. Since the technology to generate such large scale heavy water to match the urgent need for nuclear power generation was not indigenously available, the technology available with Canada and France was utilised for installation of first generation heavy water plants in India. However, the peaceful nuclear experiment conducted by India in 1974 caused resentment among the countries that supplied Heavy Water technology to India and they stopped all technological help and assistance in nuclear field. Thereafter, it was the story of India going alone in heavy water production. That made India meets successfully all challenges on the way to installation, commissioning and sustained operation of all plants. Today we have six operating Heavy Water plants, spread all over the country. We have reached a stage, a change from a situation of crunch to a level of not only self sufficiency but to a

Technical status study of heavy water enrichment

International Nuclear Information System (INIS)

Sukarsono; Imam Dahroni; Didik Herhady

2007-01-01

Technical status study of heavy water enrichment in Indonesia and also in the world has been done. Heavy water enrichment processes have been investigated were water distillation, hydrogen distillation, laser enrichment, electrolysis and isotop exchange. For the isotop exchange, the chemical pair can be used were water-hydrogen sulphite, ammonium-hydrogen, aminomethane-hydrogen, and water-hydrogen. For the isotope exchange, there was carried out by mono thermal or bi thermal. The highest producer of heavy water is Canada, and the other producer is USA, Norwegian and India. The processes be used in the world are isotope exchange Girdler Sulphide (GS), distillation and electrolysis. Research of heavy water carried out in Batan Yogyakarta, has a purpose to know the characteristic of heavy water purification. Several apparatus which has erected were 3 distillation column: Pyrex glass of 2 m tall, stainless steel column of 3 m tall and steel of 6 m tall. Electrolysis apparatus is 50 cell electrolysis and an isotope exchange unit which has catalyst: Ni- Cr 2 O 3 and Pt-Carbon. These apparatus were not ready to operate. (author)

Canadian heavy water production

International Nuclear Information System (INIS)

Dahlinger, A.; Lockerby, W.E.; Rae, H.K.

1977-01-01

The paper reviews Canadian experience in the production of heavy water, presents a long-term supply projection, relates this projection to the anticipated long-term electrical energy demand, and highlights principal areas for further improvement that form the bulk of the Canadian R and D programme on heavy water processes. Six Canadian heavy water plants with a total design capacity of 4000Mg/a are in operation or under construction. All use the Girdler-Sulphide (GS) process, which is based on deuterium exchange between water and hydrogen sulphide. Early operating problems have been overcome and the plants have demonstrated annual capacity factors in excess of 70%, with short-term production rates equal to design rates. Areas for further improvement are: to increase production rates by optimizing the control of foaming to give both higher sieve tray efficiency and higher flow rates, to reduce the incapacity due to deposition of pyrite (FeS 2 ) and sulphur (between 5% and 10%), and to improve process control and optimization of operating conditions by the application of mathematical simulations of the detailed deuterium profile throughout each plant. Other processes being studied, which look potentially attractive are the hydrogen-water exchange and the hydrogen-amine exchange. Even if they become successful competitors to the GS process, the latter is likely to remain the dominant production method for the next 10-20 years. This programme, when related to the long-term electricity demand, indicates that heavy water supply and demand are in reasonable balance and that the Candu programme will not be inhibited because of shortages of this commodity. (author)

Topical and working papers on heavy water requirements and availability

International Nuclear Information System (INIS)

The documents included in this report are: Heavy water requirements and availability; technological infrastructure for heavy water plants; heavy water plant siting; hydrogen and methane availability; economics of heavy water production; monothermal, water fed heavy water process based on the ammonia/hydrogen isotopic exchange; production strategies to meet demand projections; hydrogen availability; deuterium sources; the independent UHDE heavy water process

Plutonium Recycle Test Reactor (PRTR). Operating Experience and Supporting R and D, Its Application to Heavy-Water Power Reactor Design and Operation

Energy Technology Data Exchange (ETDEWEB)

Harty, H. [Battelle Memorial Institute, Pacific Northwest Laboratories, Richland, WA (United States)

1968-04-15

Convincing answers to questions about heavy-water, pressure-tube, power reactors, e.g. pressure-tube serviceability, heavy-water management problems, long-term behaviour of special pressure-tube reactor components, and unique operating maintenance problems (compared to light-water reactors) must be based on actual operating experience with that type of reactor. PRTR operating experience and supporting R and D studies, although not always simple extrapolations to power reactors, can be summarized in a context applicable to future heavy-water power reactors, as follows: 1. Pressure-tube life, in a practical case, need not be limited by creep, gross hydriding, corrosion, or mechanical damage. The possibility that growth of a defect (perhaps service-induced) to a size that is critical under certain operating conditions, remains a primary unknown in pressure- tube life extrapolations. A pressure-tube failure in PRTR (combined with gross release of fuel material) proved only slightly more inconvenient, time consuming, and damaging to the reactor proper, than occurred with a gross failure of a fuel element in PRTR. 2. Routine operating losses of heavy water appear tractable in heavy-water-cooled power reactors; losses from low-pressure systems can be insignificant over the life of a plant. Non-routine losses may prove to be the largest component of loss over the life of a plant. 3. The performance of special components in PRTR, e.g. the calandria and shields, has not deteriorated despite being subjected to non-standard operating conditions. The calandria now contains a light-water reflector with single barrier separation from the heavy-water moderator. The carbon steel shields (containing carbon steel shot) show no deterioration based on pressure drop measurements and piping activation immediately outside the shields. The helium pressurization system (for primary coolant pressurization) remains a high maintenance system, and cannot be recommended for power reactors, based

The Canadian heavy water situation

International Nuclear Information System (INIS)

Dahlinger, A.

1975-08-01

Existing heavy water plants in Canada are producing at a satisfactory rate and currently planned capacity is in balance with projected needs. By 1980, we shall have Girdler-Sulphide plants installed with a design capacity of almost 600 kg/h. Effort is required to minimize production costs for heavy water and to ensure that costs do not increase faster than the current inflationary trend. (Author)

IR analyzer spots heavy water leaks

International Nuclear Information System (INIS)

Anon.

1978-01-01

A correlation spectrometer developed by Barringer Research Ltd. (in collaboration with Atomic Energy of Canada and Ontario Hydro) is used to measure HDO concentrations in DTO in the final (distillation) stage of heavy-water production. A unit has been installed at Bruce Heavy Water Plant. Previously, such spectrometers had been installed to detect heavy-water leaks in CANDU reactors. The principle on which the instrument works is explained, with illustrations. It works by comparing the absorption at 2.9 μm, due to HDO, with that at 2.6 μm, due to both HDO and D 2 O. (N.D.H.)

Moderator clean-up system in a heavy water reactor

International Nuclear Information System (INIS)

Sasada, Yasuhiro; Hamamura, Kenji.

1983-01-01

Purpose: To decrease the fluctuation of the poison concentration in heavy water moderator due to a heavy water clean-up system. Constitution: To a calandria tank filled with heavy water as poison-containing moderators, are connected both end of a pipeway through which heavy water flows and to which a clean-up device is provided. Strongly basic resin is filled within the clean-up device and a cooler is disposed to a pipeway at the upstream of the clean-up device. In this structure, the temperature of heavy water at the inlet of the clean-up device at a constant level between the temperature at the exit of the cooler and the lowest temperature for the moderator to thereby decrease the fluctuation in the poison concentration in the heavy water moderator due to the heavy water clean-up device. (Moriyama, K.)

Future trends in heavy water production

International Nuclear Information System (INIS)

Galley, M.R.

1983-10-01

World heavy water production has spanned nearly fifty years and, for much of that period, the commodity was often in short supply, but that situation has changed, at least in Canada. There are now adequate reserves of heavy water and sufficient installed production capacity to service Canadian domestic and export demands for the next ten years or beyond. More than 90 percent of the world's inventory of heavy water has been produced by the GS process but this may not be the method that is chosen when the time comes to expand heavy water production again. Other countries, such as India and Argentina, have already chosen ammonia-hydrogen exchange as an alternative technology for part of their domestic production programs. Despite the present surplus of heavy water, research and development of new technologies is very active, particularly in Canada and Japan, because it is recognized that there are still attractive opportunities for future production by processes that are both less expensive and environmentally more acceptable, than either the demonstrated GS process or ammonia-hydrogen alternative. This paper describes the prospects for some of these new processes, contrasts them with the present established methods and assesses the probable impact on the future supply situation

Water issues associated with heavy oil production.

Energy Technology Data Exchange (ETDEWEB)

Veil, J. A.; Quinn, J. J.; Environmental Science Division

2008-11-28

Crude oil occurs in many different forms throughout the world. An important characteristic of crude oil that affects the ease with which it can be produced is its density and viscosity. Lighter crude oil typically can be produced more easily and at lower cost than heavier crude oil. Historically, much of the nation's oil supply came from domestic or international light or medium crude oil sources. California's extensive heavy oil production for more than a century is a notable exception. Oil and gas companies are actively looking toward heavier crude oil sources to help meet demands and to take advantage of large heavy oil reserves located in North and South America. Heavy oil includes very viscous oil resources like those found in some fields in California and Venezuela, oil shale, and tar sands (called oil sands in Canada). These are described in more detail in the next chapter. Water is integrally associated with conventional oil production. Produced water is the largest byproduct associated with oil production. The cost of managing large volumes of produced water is an important component of the overall cost of producing oil. Most mature oil fields rely on injected water to maintain formation pressure during production. The processes involved with heavy oil production often require external water supplies for steam generation, washing, and other steps. While some heavy oil processes generate produced water, others generate different types of industrial wastewater. Management and disposition of the wastewater presents challenges and costs for the operators. This report describes water requirements relating to heavy oil production and potential sources for that water. The report also describes how water is used and the resulting water quality impacts associated with heavy oil production.

Ultrasonic relaxation studies associated with n-octylamine-heavy water

International Nuclear Information System (INIS)

Kor, S.K.; Singh, R.K.

1994-01-01

Ultrasonic absorption measurements have been carried out in lyotropic liquid crystalline system n-octylamine/heavy water in the frequency range 5-65 MHz and at temperatures 30 degC and 37 degC at different concentrations of heavy water in octylamine. Velocity has been measured using interferometric technique at 2 MHz at different concentrations of heavy water. Ultrasonic absorption coefficients at different concentrations in the concentration range 0.3-0.9 m.f. heavy water have been found to show a maxima in the absorption curve at critical concentration (∼0.85 m.f. heavy water). This peak has been found to shift towards lower concentrations of heavy water at higher frequencies. Results have been analysed and it has been found that single relaxation process takes place around 30 MHz and this has been attributed to aggregation of octylamine and heavy water molecules. (author). 8 refs., 6 figs., 3 tabs

A study of Cirus heavy water system isotopic purity

International Nuclear Information System (INIS)

Thomas, Shibu; Sahu, A.K.; Unni, V.K.P.; Pant, R.C.

2000-01-01

Cirus uses heavy water as moderator and helium as cover gas. Approximately one tonne of heavy water was added to the system every year for routine make up. Isotopic purity (IP) of this water used for addition was always higher than that of the system. Though this should increase IP of heavy water in the system, it has remained almost at the same level, over the years. A study was carried out to estimate the extent of improvement in IP of heavy water in the system that should have occurred because of this and other factors in last 30 years. Reasons for non-occurrence of such an improvement were explored. Ion exchange resins used for purification of heavy water and air ingress into helium cover gas system appear to be the principal sources of entry of light water into heavy water system. (author)

Radiation safety experience in upgrading 2-5% heavy water wastes at Heavy Water Plant, Nangal (Preprint No. SA-7)

International Nuclear Information System (INIS)

Sadhukhan, H.K.; Behl, D.; Ramraj; Iyengar, T.S.; Sadarangani, S.H.; Vaze, P.K.; Soman, S.D.

1989-04-01

This paper describes the radiological safety experience in upgrading 2-5% heavy water wastes at Heavy Water Plant at Nangal at the third stage electrolysers. The feed water concentrations at the third stage electrolyer was determined after a safety analysis study and pilot plant experiment, which gave the optimal concentrations of 1 to 1.5 mCi (3.7 to 5.5 x 10 7 Bq) per litre per minute feed from a submerged SS tank containing 2-5% heavy water wastes. This process not only yielded an efficient recovery of reactor grade heavy water but contained the tritium activity in the third stage electrolysers and in the final product viz., heavy water. The tritium concentrations were continuously monitore d by liquid scintillation counting method at all the three stages of electrolysis plant, the distillation plant, the heavy water filling rooms, the drains, the ambient air, the product fertilizer (calcium ammonia nitrate) and the Sutlej River and found to be well within the safety limits set for general public at large. The HD and D 2 process streams in the palnt were monitored using fill-in type of ionization chambers designed for the purpose, which served a D 2 inventory check as well. There was no internal exposure to any personnel during the entire period of programme. (author). 2 tabs

Cylinder-type bottom reflector

International Nuclear Information System (INIS)

Elter, C.; Fritz, R.; Kissel, K.F.; Schoening, J.

1982-01-01

Proposal of a bottom reflector for gas-cooled nuclear reactor plants with a pebble bed of spherical fuel elements, where the horizontal forces acting from the core and the bottom reflector upon the side reflector are equally distributed. This is attained by the upper edge of the bottom reflector being placed levelly and by the angle of inclination of the recesses varying. (orig.) [de

Heavy water leak detection using diffusion sampler

International Nuclear Information System (INIS)

Joshi, M.L.; Hussain, S.A.

1990-01-01

In the Pressurrised Heavy Water Reactors (PHWRs) detection of the sources of heavy water leaks is importent both for the purpose of radiation hazard control as well as for the reduction of escape/loss of heavy water which, is an expensive nuclear material. This paper describes an application of tritium diffusion sampler for heavy water leak detection. The diffusion sampler comprises an usual tritium counting glass vial with a special orifice. The counting vial has water vapour, deficient in HTO concentration. The HTO present outside diffuses in the vial through the orifice, gets exchanged with water of the wet filter paper kept at the bottom and the moisture in the vial atmosphere which has HTO concentration lower than that outside. This results in continuation of net movement of HTO in the vial. The exchanged tritium is counted in liquid scintillation spectrometer. The method has a sensitivity of 10000 dpm/DAC-h. (author). 2 figs., 2 ta bs

Numerical analysis and optimisation of heavy water upgrading column

International Nuclear Information System (INIS)

Sankar, Rama; Ghosh, Brindaban; Bhanja, K.

2013-01-01

In the 'Pressurised Heavy Water' type of reactors, heavy water is used both as moderator and coolant. During operation of reactor downgraded heavy water is generated that needs to be upgraded for reuse in the reactor. When the isotopic purity of heavy water becomes less than 99.75%, it is termed as downgraded heavy water. Downgraded heavy water also contains impurity such as corrosion products, dirt, oil etc. Upgradation of downgraded heavy water is normally done in two steps: (i) Purification: In this step downgraded heavy water is first purified to remove corrosion products, dirt, oil, etc. and (ii) Upgradation of heavy water to increase its isotopic purity, this step is carried out by vacuum distillation of downgraded heavy water after purification. This project is aimed at mathematical modelling and numerical simulation of heavy water upgrading column. Modelling and simulation studies of the upgradation column are based on equilibrium stage model to evaluate the effect of feed location, pressure, feed composition, reflux ratio in the packed column for given reboiler and condenser duty of distillation column. State to stage modelling of two-phase two-component flow has constitutes the overall modelling of the column. The governing equations consist of stage-wise species and overall mass continuity and stage-wise energy balance. This results in tridigonal matrix equation for stage liquid fractions for heavy and light water. The stage-wise liquid flow rates and temperatures are governed by stage-wise mass and energy balance. The combined form of the corresponding governing equations, with the incorporation of thermodynamic equation of states, form a system of nonlinear equations. This system have been resolved numerically using modified Newton-Raphson method. A code in the MATLAB platform has been developed by on above numerical procedure. The optimisation of the column operating conditions is to be carried out based on parametric studies and analysis of different

Topical and working papers on heavy water accountability and safeguards

International Nuclear Information System (INIS)

This report contains the following papers: 1) Statement of IAEA concerning safeguarding of heavy water; 2) Preliminary Canadian Comments on IAEA document on heavy water safeguards; 3) Heavy water accountability 03.10.78; 4) Heavy water accountability 05.04.79

High conversion heavy water moderated reactor

International Nuclear Information System (INIS)

Miyawaki, Yoshio; Wakabayashi, Toshio.

1989-01-01

In the present invention, fuel rods using uranium-plutonium oxide mixture fuels are arranged in a square lattice at the same pitch as that in light water cooled reactor and heavy water moderators are used. Accordingly, the volume ratio (Vm/Vf) between the moderator and the fuel can be, for example, of about 2. When heavy water is used for the moderator (coolant), since the moderating effect of heavy water is lower than that of light water, a high conversion ratio of not less than 0.8 can be obtained even if the fuel rod arrangement is equal to that of PWR (Vm/Vf about 2). Accordingly, it is possible to avoid problems caused by dense arrangement of fuel rods as in high conversion rate light water cooled reactors. That is, there are no more troubles in view of thermal hydrodynamic characteristics, re-flooding upon loss of coolant accident, etc., as well as the fuel production cost is not increased. (K.M.)

Handbook of reflector antennas and feed systems v.3 applications of reflectors

CERN Document Server

Rao, Sudhakar; Sharma, Satish K

2013-01-01

This is the first truly comprehensive and most up-to-date handbook available on modern reflector antennas and feed sources for diversified space and ground applications. There has never been such an all-encompassing reflector handbook in print, and no currently available title offers coverage of such recent research developments. The Handbook consists of three volumes. Volume III focuses on the range of reflector antenna applications, including space, terrestrial, and radar. The intent of this book volume is to provide practical applications and design information on reflector antennas used fo

Heavy water lattices: Second panel report

International Nuclear Information System (INIS)

1963-01-01

The panel was attended by prominent physicists from most of the laboratories engaged in the field of heavy water lattices throughout the world. The participants presented written contributions and status reports describing the past history and plans for further development of heavy-water reactors. Valuable discussions took place, during which recommendations for future work were formulated. Refs, figs, tabs

Heavy water lattices: Second panel report

Energy Technology Data Exchange (ETDEWEB)

1963-09-15

The panel was attended by prominent physicists from most of the laboratories engaged in the field of heavy water lattices throughout the world. The participants presented written contributions and status reports describing the past history and plans for further development of heavy-water reactors. Valuable discussions took place, during which recommendations for future work were formulated. Refs, figs, tabs.

The Canadian heavy water supply program

International Nuclear Information System (INIS)

Dahlinger, A.; McNally, P.J.

1976-06-01

The performance to date of individual Canadian heavy water plants is described in detail as are the current plant construction plans. These data, when related to the long-term electricity demand indicate that heavy water supply and demand are in reasonable balance and that the CANDU program will not be inhibited because of shortages of the commodity. (author)

Heavy water. A production alternative for Venezuela

International Nuclear Information System (INIS)

A survey of heavy water production methods is made. Main facts about isotopic and distillation methods, reforming and coupling to a Hydrogen distillation plant are presented. A feasibility study on heavy water production in Venezuela is suggested

Heavy water physical verification in power plants

International Nuclear Information System (INIS)

Morsy, S.; Schuricht, V.; Beetle, T.; Szabo, E.

1986-01-01

This paper is a report on the Agency experience in verifying heavy water inventories in power plants. The safeguards objectives and goals for such activities are defined in the paper. The heavy water is stratified according to the flow within the power plant, including upgraders. A safeguards scheme based on a combination of records auditing, comparing records and reports, and physical verification has been developed. This scheme has elevated the status of heavy water safeguards to a level comparable to nuclear material safeguards in bulk facilities. It leads to attribute and variable verification of the heavy water inventory in the different system components and in the store. The verification methods include volume and weight determination, sampling and analysis, non-destructive assay (NDA), and criticality check. The analysis of the different measurement methods and their limits of accuracy are discussed in the paper

Seismic re-evaluation of Heavy Water Plant, Kota

International Nuclear Information System (INIS)

Parulekar, Y.M.; Reddy, G.R.; Vaze, K.K.; Kushwaha, H.S.

2003-10-01

This report deals with seismic re-evaluation of Heavy Water Plant, Kota. Heavy Water Plant, Kota handles considerable amount of H 2 S gas, which is very toxic. During the original design stage as per IS 1893-1966 seismic coefficient for zone-I was zero. Therefore earthquake and its effects were not considered while designing the heavy water plant structures. However as per IS 1893 (1984) the seismic coefficient for zone-I is 0.01 g. Hence seismic re-evaluation of various structures of the heavy water plant is carried out. Analysis of the heavy water plant structures was carried out for self weight, equipment load and earthquake load. Pressure loading was also considered in case of H 2 S storage tanks. Soil structure interaction effect was considered in the analysis. The combined stresses in the structures due to earthquake and dead load were checked with the allowable stresses. (author)

Heavy water: a distinctive and essential component of CANDU

International Nuclear Information System (INIS)

Miller, A.I.; van Alstyne, H.M.

1994-06-01

The exceptional properties of heavy water as a neutron moderator provide one of the distinctive features of CANDU reactors. Although most of the chemical and physical properties of deuterium and protium (mass 1 hydrogen) are appreciably different, the low terrestrial abundance of deuterium makes the separation of heavy water a relatively costly process, and so of considerable importance to the CANDU system. World heavy-water supplies are currently provided by the Girdler-Sulphide process or processes based on ammonia-hydrogen exchange. Due to cost and hazard considerations, new processes will be required for the production of heavy water in and beyond the next decade. Through AECL's development and refinement of wetproofed catalysts for the exchange of hydrogen isotopes between water and hydrogen, a family of new processes is expected to be deployed. Two monothermal processes, CECE (Combined Electrolysis and Catalytic Exchange, using water-to-hydrogen conversion by electrolysis) and CIRCE (Combined Industrially Reformed hydrogen and Catalytic Exchange, based on steam reforming of hydrocarbons), are furthest advanced. Besides its use for heavy-water production, the CECE process is a highly effective technology for heavy-water upgrading and for tritium separation from heavy (or light) water. (author). 10 refs., 1 tab., 7 figs

CNGS Reflector installed

CERN Multimedia

2006-01-01

A major component that will help target the CNGS neutrino beam for its 732km journey through the earth's crust, from CERN to the Gran Sasso laboratory in Italy, has been installed in its final position. The transport of the huge magnetic horn reflector through the CNGS access gallery. A team from CNGS and TS/IC, and the contractors DBS, transported the magnetic horn reflector on 5th December, in a carefully conducted operation that took just under two hours. The reflector is 7m long, 1.6m in diameter and 1.6 tonnes in weight. With only a matter of centimetres to spare on either side, the reflector was transported through the CNGS access gallery, before being installed in the experiment's target chamber. The larger of two magnetic horns, the reflector will help refocus sprays of high energy pions and kaons emitted after a 0.5MW stream of protons from the Super Proton Synchrotron (SPS) strikes nucleons in a graphite target. The horns are toroidal magnetic lenses and work with high pulsed currents: 150 kA f...

Design and measured performances of a plane reflector augmented box-type solar-energy cooker

International Nuclear Information System (INIS)

Ekechukwu, O.V.

2001-06-01

The design philosophy, construction and measured performances of a plane-reflector augmented box-type solar-energy cooker are presented. The experimental solar cooker consists of an aluminum plate absorber painted matt black and a double-glazed lid. The bottom and sides are lagged with fibreglass wool insulator. The reflector consists of a wooden-framed commercially-available specular plane mirror which is sized to form a cover for the box when not in use. Provision is made for four cooking vessels each capable of holding up to 1 kg of water. Results of thermal performance tests show stagnation absorber plate temperatures of 138 deg. C and 119 deg. C for the cooker with and without the plane reflector in place, respectively. Boiling times of 60 minutes (3600 seconds) and 70 minutes (4200 seconds) for 1 kg of water, for the cooker with and without the reflector in place, respectively, were recorded. The solar cooker performance has been rated using the first figure of merit (F 1 ) on the no-load test and the second figure of merit (F 2 ) on the sensible heat tests. Predicted water boiling times using the two figures of merit compared favourable with measured values. The performance of the cooker with the plane reflector in place was improved tremendously compared to that without the reflector in place. (author)

Process for the extraction of tritium from heavy water

International Nuclear Information System (INIS)

Dombra, A.H.

1984-01-01

The object of the invention is achieved by a process for the extraction of tritium from a liquid heavy water stream comprising: contacting the heavy water with a countercurrent gaseous deuterium stream in a column packed with a water-repellent catalyst such that tritium is transferred by isotopic exchange from the liquid heavy water stream to the gaseous deuterium stream

Method of operating heavy water moderated reactors

International Nuclear Information System (INIS)

Masuda, Hiroyuki.

1980-01-01

Purpose: To enable stabilized reactor control, and improve the working rate and the safety of the reactor by removing liquid poison in heavy water while maintaining the power level constant to thereby render the void coefficient of the coolants negative in the low power operation. Method: The operation device for a heavy water moderated reactor comprises a power detector for the reactor, a void coefficient calculator for coolants, control rods inserted into the reactor, a poison regulator for dissolving poisons into or removing them out of heavy water and a device for removing the poisons by the poison regulator device while maintaining the predetermined power level or inserting the control rods by the signals from the power detector and the void coefficient calculator in the high temperature stand-by conditions of the reactor. Then, the heavy water moderated reactor is operated so that liquid poisons in the heavy water are eliminated in the high temperature stand-by condition prior to the start for the power up while maintaining the power level constant and the plurality of control rods are inserted into the reactor core and the void coefficient of the coolants is rendered negative in the low power operation. (Seki, T.)

Slovakia: Proposal of movable reflector for fast reactor design

International Nuclear Information System (INIS)

Vrban, B.

2015-01-01

In fast reactors a larger migration area leading to a significant leak of neutrons can be observed because especially the transport cross-sections are in general smaller as compared to light water reactors. The utilization of a moveable reflector system in conjunction with dedicated safety control rods can increase the ability of accident managing due to enhanced escaping neutrons which otherwise would be reflected back into the fuel zone. The paper demonstrates the possibility of better controlling the transient reactor by additionally moving selected reflector subassemblies equipped with the neutron trap. The main purpose of the analysis of the Gas-cooled Fast Reactor (GFR) presented in the full paper is investigation of the kinetic parameters and of the control and reflector rod worth, as well as optimization of the parts used for partial reflector withdrawal. The results found in this study may serve for future design improvements of other designs such as the liquid metal cooled fast reactors

Heavy water pumps; Pumpe D{sub 2}O

Energy Technology Data Exchange (ETDEWEB)

Zecevic, V; Nikolic, M

1963-12-15

Continuous increase of radiation intensity was observed on all the elements in the heavy water system during first three years of RA reactor operation. The analysis of heavy water has shown the existence of radioactive cobalt. It was found that cobalt comes from stellite, cobalt based alloy which was used for coating of the heavy water pump discs in order to increase resistance to wearing. Cobalt was removed from the surfaces due to friction, and transferred by heavy water into the reactor where it has been irradiated for 29 876 MWh up to 8-15 Ci/g. Radioactive cobalt contaminated all the surfaces of aluminium and stainless steel parts. This report includes detailed description of heavy water pumps repair, exchange of stellite coated parts, decontamination of the heavy water system, distillation of heavy water. [Serbo-Croat] U toku prve tri godine eksploatacije reaktora RA uocen je neprekidni porast intenziteta zracenja na svim elementima u teskovodnom sistemu. Analizom teske vode utvrdjeno je postojanje radioaktivnog kobalta. Ustanovljeno je da kobalt potice od stelita, legure na bazi kobalta kojim su presvuceni rukavci vratila teskovodnih pumpi radi otpornosi na habanje. Kobalt je trenjem skidan sa povrsina, u toku rada prenosen je teskom vodom u reaktor i ozracivan u toku 29 876 MWh do specificne aktivnosti 8-15 Ci/g. Radioaktivni kobalt je kontaminirao sve povrsine od aluminijuma i nerdjajuceg celika. Ovaj izvestaj sadrzi detaljan opis remonta pumpi, zamene delova teskovodnih pumpi novim delovima bez stelitnog sloja, dekontaminacije teskovodnog sistema, destilacije teske vode.

A Drinking Water Sensor for Lead and Other Heavy Metals.

Science.gov (United States)

Lin, Wen-Chi; Li, Zhongrui; Burns, Mark A

2017-09-05

Leakage of lead and other heavy metals into drinking water is a significant health risk and one that is not easily detected. We have developed simple sensors containing only platinum electrodes for the detection of heavy metal contamination in drinking water. The two-electrode sensor can identify the existence of a variety of heavy metals in drinking water, and the four-electrode sensor can distinguish lead from other heavy metals in solution. No false-positive response is generated when the sensors are placed in simulated and actual tap water contaminated by heavy metals. Lead detection on the four-electrode sensor is not affected by the presence of common ions in tap water. Experimental results suggest the sensors can be embedded in water service lines for long-time use until lead or other heavy metals are detected. With its low cost (∼$0.10/sensor) and the possibility of long-term operation, the sensors are ideal for heavy metal detection of drinking water.

Alkali metal and ammonium chlorides in water and heavy water (binary systems)

CERN Document Server

Cohen-Adad, R

1991-01-01

This volume surveys the data available in the literature for solid-fluid solubility equilibria plus selected solid-liquid-vapour equilibria, for binary systems containing alkali and ammonium chlorides in water or heavy water. Solubilities covered are lithium chloride, sodium chloride, potassium chloride, rubidium chloride, caesium chloride and ammonium chloride in water and heavy water.

Procedure for operating a heavy water cooled power reactor

International Nuclear Information System (INIS)

Rau, P.; Kumpf, H.

1981-01-01

Nuclear reactors cooled by heavy water usually have equipment for fuel element exchange during operation, with the primary circuit remaining contained. This fuel element exchange equipment is expensive and complicated in many respects. According to the invention, the heavy water is therefore replaced by light water after a certain time of operation in such way that light water is led in and heavy water is led off. After the replacement, at least a quarter of the fuel elements of the reactor core is exchanged with the reactor pressure vessel being open. Then the light water serving as a shielding is replaced by heavy water, with the reactor pressure vessel being closed. The invention is of interest particularly for high-conversion reactors. (orig.) [de

Tailored reflectors for illumination.

Science.gov (United States)

Jenkins, D; Winston, R

1996-04-01

We report on tailored reflector design methods that allow the placement of general illumination patterns onto a target plane. The use of a new integral design method based on the edge-ray principle of nonimaging optics gives much more compact reflector shapes by eliminating the need for a gap between the source and the reflector profile. In addition, the reflectivity of the reflector is incorporated as a design parameter. We show the performance of design for constant irradiance on a distant plane, and we show how a leading-edge-ray method may be used to achieve general illumination patterns on nearby targets.

Coupling in reflector arrays

DEFF Research Database (Denmark)

Appel-Hansen, Jørgen

1968-01-01

In order to reduce the space occupied by a reflector array, it is desirable to arrange the array antennas as close to each other as possible; however, in this case coupling between the array antennas will reduce the reflecting properties of the reflector array. The purpose of the present communic......In order to reduce the space occupied by a reflector array, it is desirable to arrange the array antennas as close to each other as possible; however, in this case coupling between the array antennas will reduce the reflecting properties of the reflector array. The purpose of the present...

Phytoremediation of water bodies contaminated with radioactive heavy metal

International Nuclear Information System (INIS)

Yan Zhen; Yuan Shichao; Ling Hui; Xie Shuibo

2012-01-01

The sources of the radioactive heavy metal in the water bodies were analyzed. The factors that affect phyto remediation of water contaminated with radioactive heavy metal were discussed. The plant species, mechanism and major technology of phyto remediation of water contaminated with radioactive heavy metal were particularly introduced. The prospective study was remarked. (authors)

Fuel and heavy water availability

International Nuclear Information System (INIS)

1980-01-01

The general guidelines for the Working Group's evaluation of the availability of nuclear fuel and heavy water were set at the Organizing Conference of the International Nuclear Fuel Cycle Evaluation (INFCE), which was held in Washington, United States of America, 19-21 October 1977. The agreed technical and economic scope for the evaluation was to: (1) Estimate needs for nuclear energy and correlated needs for uranium and heavy water according to different fuel cycle strategies; (2) Review uranium availability with specific regard to: Assessment of resources and production capacities; policies and incentives for encouraging exploration and production including joint ventures; marketing policies and/or guarantees of sales for companies investing in exploration and production; marketing policies and/or guarantees of supply for utilities; technical development of exploration, mining and milling methods; (3) Review heavy water availability; (4) Review thorium availability; (5) Consider special needs of developing countries. The illustrations of availability and requirements developed in this report do provide a useful framework for considering future options and alternatives for the development of nuclear power

Production of heavy water by photodesorption

International Nuclear Information System (INIS)

Gangwer, T.; Goldstein, M.K.

1976-01-01

Research has recently brought attention to the laser as a tool for isotope enrichment. So far the main thrust of this effort has been toward uranium enrichment; however, numerous successes in other areas have been demonstrated. Isotopes of boron, sulfur, chlorine, and carbon have been separated. A new technique is proposed for laser isotope enrichment. The technique, referred to as photodesorption, involves selective isotopic excitation of molecules adsorbed on a surface such that an enrichment results from subsequent physical or chemical events undergone by the excited molecules. The specific processes of concern are the physical photodesorption enrichment of heavy water from light water and tritiated water from heavy water. The ability to work directly with water molecules has significant advantages for a commercial process. A photodesorption enrichment process has been forumulated and some analyses have been performed. This process is described and some preliminary cost estimates are made which assume successful accomplishment of the major R and D objectives of the new process. The results indicate that the process has the promise of a significant reduction in the cost of heavy water and that further study is warranted

The heavy water production plant at Arroyito, Argentina

International Nuclear Information System (INIS)

Ecabert, R.

1984-01-01

The author describes the construction of an industrial heavy water production plant (Planta Industrial de Agua Pesada, PIAP) in Argentina. The heavy water enrichment is based on a hydrogen/ammonia isotope exchange. (Auth.)

Simultaneous delivery of electron beam therapy and ultrasound hyperthermia using scanning reflectors: a feasibility study

International Nuclear Information System (INIS)

Moros, Eduardo G.; Straube, William L.; Klein, Eric E.; Yousaf, Muhammed; Myerson, Robert J.

1995-01-01

Purpose: The feasibility of simultaneously delivering external electron beam radiation and superficial hyperthermia using a scanning ultrasound reflector-array system (SURAS) was experimentally investigated and demonstrated. Methods and Materials: A new system uses a scanning reflector to distribute the acoustic energy from a planar ultrasound array over the surface of the target volume. External photon/electron beams can be concurrently delivered with hyperthermia by irradiating through the scanning reflectors. That is, this system enables the acoustic waves and the radiation beams to enter the target volume from the same direction. Reflectors were constructed of air-equivalent materials for maximum acoustic reflection and minimum radiation attenuation. Acoustically, the air reflectors were compared to brass reflectors (assumed ideal) for reflectivity and specular quality using several single transducers ranging in frequency from 0.68 to 4.8 MHz. The relative reflectivity was determined from acoustic power measurements using a force-balance technique. The specular quality was assessed by comparing the acoustic pressure fields reflected by air reflectors with those reflected by brass reflectors. Also, acoustic pressure fields generated by a SURAS prototype for two different arrays (2.24 and 4.5 MHz) were measured to investigate field distribution variations as a function of the distance separating the array and the scanning reflector. All pressure fields were measured with a hydrophone in a degassed water tank. Finally, to determine the effect of the air reflectors on electron dose distributions, these were measured using film in a water-equivalent solid phantom after passage of a 20 MeV electron beam through the SURAS. These measurements were performed with the reflector scanning continuously across the electron beam and at rest within the electron beam. Results: The measurements performed using single ultrasound transducers showed that the air reflectors had

Standards for heavy water concentration determinations in light water

International Nuclear Information System (INIS)

Varlam, M.; Steflea, D.; Pavelescu, M.

1995-01-01

The paper presents a method to prepare heavy water -light water standards within the range 144 ppm - 1%. A formula for computing standards concentration based on initial concentration of D 2 O and distilled water is given

Overcoming technology - obsolescence: a case study in Heavy Water Plant

International Nuclear Information System (INIS)

Gupta, O.P.; Sonde, R.R.; Wechalekar, A.K.

2002-01-01

Ammonia based Heavy Water Plants in India are set up essentially in conjunction with fertiliser plants for the supply of feed synthesis gas. Earlier ammonia was being produced in fertiliser plants using high-pressure technology which was highly energy intensive. However with fast developments in the field of production of ammonia, fertiliser plants are switching over to low pressure technology. Ammonia based heavy water plants have to operate on pressures corresponding to that of fertiliser plants. Due to low pressures in production of ammonia, heavy water plants would also be required to operate at low pressures than the existing operating pressures. This problem was faced at Heavy Water Plant at Baroda where GSFC supplying synthesis gas switched over to low pressure technology making it imperative on the part of Heavy Water Board to carry out modification to the main plant for continued operation of Heavy Water Plant, Baroda. Anticipating similar problems due to production of ammonia at lower pressures in other fertiliser plants linked to existing Heavy Water Plants, it became necessary for HWB to develop water ammonia front end. The feed in such a case would be water instead of synthesis gas. This would enable HWB to dispense with dependence on fertiliser plants especially if grass-root ammonia based heavy water plants are to be set up. Incorporation of water ammonia front end would enable HWB to de link ammonia based heavy water plants with fertiliser plants. This paper discusses the advantage of de linking heavy water plant respective fertiliser plant by incorporating water ammonia front end and technical issues related to front end technology. A novel concept of ammonia absorption refrigeration (AAR) was considered for the process integration with the front end. The incorporation of AAR with water ammonia front-end configuration utilizes liquid ammonia refrigerant to generate refrigeration without additional energy input which otherwise would have been

Performance improvement of the finned passive PVT system using reflectors like removable insulation covers

International Nuclear Information System (INIS)

Ziapour, Behrooz M.; Palideh, Vahid; Mokhtari, Farhad

2016-01-01

Highlights: • A passive PVT system means the combination of a PV panel and a compact solar water heater. • Comparative study was done on performance characteristics in passive and hybrid PVT systems. • Reflectors effects on performance of a finned passive PVT system were numerically studied. • Results show that the finned passive PVT system has higher performance than the hybrid type. • Reflectors reduce the night heat losses and increase the solar radiation rate on PVT system. - Abstract: A passive photovoltaic–thermal system (PVT) is the combination of a photovoltaic (PV) panel and a compact solar water heater for co-generation of heat and electricity. This system bears considerable heat losses to ambient, particularly at noncollection times. One simple way to overcome this problem is to use a removable insulation cover on the collector's outer glazing. In this paper, the effects of the reflectors on day and night performance of a finned passive PVT system were numerically studied. At nonenergy collection time, the reflectors can turn and cover the collector cover glass as a nonconductor material. Simulation results showed that the reflectors reduce the night heat losses and increase the solar radiation rate on the absorber plate. The use of removable insulation reflectors resulted to saving extra sensibly thermal energy. Also, the solar cells power generation (P_s_c), in the case of reflectors installed, was reinforced.

Electrolytic process for upgrading heavy water (Preprint No. PD-16)

International Nuclear Information System (INIS)

Rammohan, K.; Sadhukhan, H.K.

1989-04-01

In the reactor system the heavy water gets depleted in concentration due to leakages, intermixing and vapour collection in boiler vault system etc. Electrolysis of water was used as a secondary plant to enrich the dilute heavy water produced in the primery plant by hydrogen-sulfide-water exchange process. The studies made in the development of this process for the upgrading of downgra ded heavy water by setting up a full size Electrolyser Test Assembly are discussed a nd complete design of a heavy water upgrading plant based on electrolytic process for MAPS and NAPP is described. (author). 7 refs., 5 figs

Flat Engineered Multichannel Reflectors

Directory of Open Access Journals (Sweden)

V. S. Asadchy

2017-09-01

Full Text Available Recent advances in engineered gradient metasurfaces have enabled unprecedented opportunities for light manipulation using optically thin sheets, such as anomalous refraction, reflection, or focusing of an incident beam. Here, we introduce a concept of multichannel functional metasurfaces, which are able to control incoming and outgoing waves in a number of propagation directions simultaneously. In particular, we reveal a possibility to engineer multichannel reflectors. Under the assumption of reciprocity and energy conservation, we find that there exist three basic functionalities of such reflectors: specular, anomalous, and retroreflections. Multichannel response of a general flat reflector can be described by a combination of these functionalities. To demonstrate the potential of the introduced concept, we design and experimentally test three different multichannel reflectors: three- and five-channel retroreflectors and a three-channel power splitter. Furthermore, by extending the concept to reflectors supporting higher-order Floquet harmonics, we forecast the emergence of other multichannel flat devices, such as isolating mirrors, complex splitters, and multi-functional gratings.

Flat Engineered Multichannel Reflectors

Science.gov (United States)

Asadchy, V. S.; Díaz-Rubio, A.; Tcvetkova, S. N.; Kwon, D.-H.; Elsakka, A.; Albooyeh, M.; Tretyakov, S. A.

2017-07-01

Recent advances in engineered gradient metasurfaces have enabled unprecedented opportunities for light manipulation using optically thin sheets, such as anomalous refraction, reflection, or focusing of an incident beam. Here, we introduce a concept of multichannel functional metasurfaces, which are able to control incoming and outgoing waves in a number of propagation directions simultaneously. In particular, we reveal a possibility to engineer multichannel reflectors. Under the assumption of reciprocity and energy conservation, we find that there exist three basic functionalities of such reflectors: specular, anomalous, and retroreflections. Multichannel response of a general flat reflector can be described by a combination of these functionalities. To demonstrate the potential of the introduced concept, we design and experimentally test three different multichannel reflectors: three- and five-channel retroreflectors and a three-channel power splitter. Furthermore, by extending the concept to reflectors supporting higher-order Floquet harmonics, we forecast the emergence of other multichannel flat devices, such as isolating mirrors, complex splitters, and multi-functional gratings.

Reflectors to Focus Wave Energy

DEFF Research Database (Denmark)

Kramer, Morten; Frigaard, Peter

2005-01-01

Wave Energy Converters (WEC’s) extract wave energy from a limited area, often a single point or line even though the wave energy is generally spread out along the wave crest. By the use of wave reflectors (reflecting walls) the wave energy is effectively focused and increased by approximately 30......-50%. Clearly longer wave reflectors will focus more wave energy than shorter wave reflectors. Thus the draw back is the increased wave forces for the longer wave reflectors. In the paper a procedure for calculating the energy efficiency and the wave forces on the reflectors are described, this by use of a 3D...... boundary element method. The calculations are verified by laboratory experiments and a very good agreement is found. The paper gives estimates of possible power benefit for different wave reflector geometries and optimal geometrical design parameters are specified. On this basis inventors of WEC’s can...

Alternate applications of heavy water in biological and technological fields

International Nuclear Information System (INIS)

Bhaskaran, M.; Prakash, R.

2005-01-01

Deuterium and its various compounds like heavy water exhibit distinctly different properties when compared to hydrogen and its compounds. The differences in properties are due to the primary and secondary isotopic effects. Though heavy water has been used solely for nuclear applications so far, its applications in life sciences and high technology areas are fast emerging. Heavy Water Board has taken up development of alternate applications of heavy water. The study taken up has indicated superior thermal stability for oral polio vaccine prepared in heavy water. This study has revealed various opportunities for application of heavy water or deuterium in life sciences and the paper dwells on these possibilities. The higher stability of compounds with deuterium has also brought in its applications in various high technology areas. These are mainly in micro electronics. Use of deuterium in manufacture of high quality optical fibres has already been established. These are also included in the paper. (author)

Characterization and treatment options for high TOC heavy water

International Nuclear Information System (INIS)

Evans, D.; Leilabadi, A.; Rudolph, A.; Williams, D.

2007-01-01

High total organic carbon (TOC) and high conductivity contamination in heavy water feed present serious problems for the operation of heavy water upgrader facilities. The authors describe the chemical analysis of a particular batch of contaminated heavy water which had resisted standard clean-up procedures. After chemical characterization, a special clean-up plan was developed and successfully tested in the laboratory, followed by its implementation at site. (author)

Thermal conductivity coefficients of water and heavy water in the liquid state up to 3700C

International Nuclear Information System (INIS)

Le Neindre, B.; Bury, P.; Tufeu, R.; Vodar, B.

1976-01-01

The thermal conductivity coefficients of water and heavy water of 99.75 percent isotopic purity were measured using a coaxial cylinder apparatus, covering room temperature to their critical temperatures, and pressures from 1 to 500 bar for water, and from 1 to 1000 bar for heavy water. Following the behavior of the thermal conductivity coefficient of water, which shows a maximum close to 135 0 C, the thermal conductivity coefficient of heavy water exhibits a maximum near 95 0 C and near saturation pressures. This maximum is displaced to higher temperatures when the pressure is increased. Under the same temperature and pressure conditions the thermal conductivity coefficient of heavy water was lower than for water. The pressure effect was similar for water and heavy water. In the temperature range of our experiments, isotherms of thermal conductivity coefficients were almost linear functions of density

Survival of tumor-bearing mice exposed to heavy water or heavy water plus methotrexate

International Nuclear Information System (INIS)

Laissue, J.A.; Buerki, H.; Berchtold, W.

1982-01-01

Moderate body deuteration combined with a cytostatic drug [methotrexate (MTX)] significantly increases the survival time of young adult DBA/2 mice bearing transplantable P815. L5178Y, or L1210 tumors. Neoplastic cells were grown in vitro from tumor stock and injected i.p. into mice from two groups, one drinking tap water, and other drinking 30% heavy water in tap water. One-half of the animals in each of these two groups was given a single injection of MTX (4 mg/kg body weight) on 3 consecutive days per week. At death, extension of primary and metastatic tumors was examined and was found to be macro- and microscopically comparable in the corresponding groups. The mean survival time of untreated mice drinking tap water was about 2 weeks following injection of the fast-growing P815, L5178Y, or L1210 (V) tumors and approximately 5 weeks after injection of cells from a slower-growing L1210 subline. Body deuteration alone roughly doubled the survival time solely of mice bearing this L1210 subline. Treatment with MTX approximately doubled the mean survival time of hosts bearing one of the fast-growing tumors. Combined treatment with heavy water and MTX increased the mean survival time of the mice in all groups by 15 to 125% as compared to control values. The reasons for this effect are unknown. However, heavy water has been shown to exert antimitotic activity and to depress the incorporation of radioactive precursors into DNA of proliferating mammalian cells. The depression of antibody formation following antigenic stimulation and the reduction in numbers of nonneoplastic lymphoid cells of mice following moderate body deuteration may have contributed to the enhancement of MTX activity in addition to other effects of deuterium

Status of advanced technology and design for water cooled reactors: Heavy water reactors

International Nuclear Information System (INIS)

1989-07-01

In 1987 the IAEA established the International Working Group on Advanced Technologies for Water-Cooled Reactors (IWGATWR). Within the framework of the IWGATWR the IAEA Technical Report on Status of Advanced Technology and Design for Water Cooled Reactors, Part I: Light Water Reactors and Part II: Heavy Water Reactors, has been undertaken to document the major current activities and trends of technological improvement and development for future water reactors. Part I of the report dealing with Light Water Reactors (LWRs) was published in 1988 (IAEA-TECDOC-479). Part II of the report covers Heavy Water Reactors (HWRs) and has now been prepared. This report is based largely upon submissions from Member States. It has been supplemented by material from the presentations at the IAEA Technical Committee and Workshop on Progress in Heavy Water Reactor Design and Technology held in Montreal, Canada, December 6-9, 1988. It is hoped that this part of the report, containing the status of advanced heavy water reactor technology up to 1988 and ongoing development programmes will aid in disseminating information to Member States and in stimulating international cooperation. Refs, figs and tabs

High purity heavy water production: need for total organic carbon determination in process water streams

International Nuclear Information System (INIS)

Ayushi; Kumar, Sangita D.; Reddy, A.V.R.; Vithal, G.K.

2009-01-01

In recent times, demand for high purity heavy water (99.98% pure) in industries and laboratories has grown by manifold. Its application started in nuclear industry with the design of CANDU reactor, which uses natural uranium as fuel. In this reactor the purest grade of heavy water is used as the moderator and the primary coolant. Diverse industrial applications like fibre optics, medicine, semiconductors etc. use high purity heavy water extensively to achieve better performance of the specific material. In all these applications there is a stringent requirement that the total organic carbon content (TOC) of high purity heavy water should be very low. This is because the presence of TOC can lead to adverse interactions in different applications. To minimize the TOC content in the final product there is a need to monitor and control the TOC content at each and every stage of heavy water production. Hence a simple, rapid and accurate method was developed for the determination of TOC content in process water samples. The paper summarizes the results obtained for the TOC content in the water samples collected from process streams of heavy water production plant. (author)

assessment of heavy metals concentration in drinking water ...

African Journals Online (AJOL)

userpc

guidelines (WHO 2005). Findings suggest that continues water quality monitoring should be carried out to check the concentration levels of heavy metals in that area, to prevent them from been above the limit of WHO. Keywords: Atomic Absorption Spectrophotometers, Heavy Metals, Water, Kauru Local. Government Area.

Heavy water cycle in the CANDU reactor

International Nuclear Information System (INIS)

Nanis, R.

2000-01-01

Hydrogen atom has two isotopes: deuterium 1 H 2 and tritium 1 H 3 . The deuterium oxide D 2 O is called heavy water due to its density of 1105.2 Kg/m 3 . Another important physical property of the heavy water is the low neutron capture section, suitable to moderate the neutrons into natural uranium fission reactor as CANDU. Due to the fact that into this reactor the fuel is cooled into the pressure tubes surrounded by a moderator, the usage of D 2 O as primary heat transport (PHT) agent is mandatory. Therefore a large amount of heavy water (approx. 500 tons) is used in a CANDU reactor. Being a costly resource - it represents 20% of the initial plant capital cost, D 2 O management is required to preserve it. (author)

Heavy water radiolysis and chemistry control of the Fugen Nuclear Power Station

International Nuclear Information System (INIS)

Ibuki, Y.; Kitabata, T.; Kato, T.

1989-01-01

A computer analysis for heavy water radiolysis clarified the mechanism of the heavy water radiolysis rate change with impurities in the heavy water and cover gas, helium. The mechanism is supported by over ten years' operational data of the heavy water radiolysis in the Fugen nuclear power station. (author)

Critical heat flux experiments in a circular tube with heavy water and light water. (AWBA Development Program)

International Nuclear Information System (INIS)

Williams, C.L.; Beus, S.G.

1980-05-01

Experiments were performed to establish the critical heat flux (CHF) characteristics of heavy water and light water. Testing was performed with the up-flow of heavy and of light water within a 0.3744 inch inside diameter circular tube with 72.3 inches of heated length. Comparisons were made between heavy water and light water critical heat flux levels for the same local equilibrium quality at CHF, operating pressure, and nominal mass velocity. Results showed that heavy water CHF values were, on the average, 8 percent below the light water CHF values

Process for the preparation of ammonia and heavy water

International Nuclear Information System (INIS)

Mandrin, C.

1980-01-01

A process for the production of ammonia and heavy water comprises the steps of enriching a flow of water with deuterium in a monothermal isotropic process; supplying a first portion of the deuterium-enriched water to a heavy water preparation plant to produce heavy water and hydrogen; storing a second portion of the deuterium-enriched water substantially without interruption during the colder half of a year; electrolytically dissociating the stored deuterium-enriched water substantially without interruption during the wamer half of a year to form hydrogen; storing a portion of the electrolytically-produced hydrogen during said warmer half of a year while supplying the remainder to a synthesis circuit of a synthesizing plant and subsequently supplying the stored hydrogen to the synthesis circuit during said colder half of a year; removing some of the synthesis gas mixture from the synthesis circuit of the synthesizing plant; burning the removed synthesis gas mixture with air to produce a mixture consisting mainly of water and nitrogen; thereafter condensing and separating the water from the mixture of water and nitrogen; supplying the nitrogen of the mixture of water and nitrogen, the hydrogen from the heavy water preparation plant and the electrolytically-produced hydrogen to the synthesis circuit of the synthesizing plant to produce ammonia; and collecting deuterium-depleted water resulting from said burning step and feeding the collected deuterium-depleted water into the monothermal process

Heavy water at Trail, British Columbia

International Nuclear Information System (INIS)

Arsenault, J.E.

2006-01-01

Today Canada stands on the threshold of a nuclear renaissance, based on the CANDU reactor family, which depends on heavy water as a moderator and for cooling. Canada has a long history with heavy water, with commercial interests beginning in 1934, a mere two years after its discovery. At one time Canada was the world's largest producer of heavy water. The Second World War stimulated interest in this rather rare substance, such that the worlds largest supply (185 kg) ended up in Canada in 1942 to support nuclear research work at the Montreal Laboratories of the National Research Council. A year later commercial production began at Trail, British Columbia, to support work that later became known as the P-9 project, associated with the Manhattan Project. The Trail plant produced heavy water from 1943 until 1956, when it was shut down. During the war years the project was so secret that Lesslie Thomson, Special Liaison Officer reporting on nuclear matters to C.D. Howe, Minister of Munitions and Supply, was discouraged from visiting Trail operations. Thomson never did visit the Trail facility during the war. In 2005 the remaining large, tall concrete exchange tower was demolished at a cost of about $2.4 million, about the same as it cost to construct the facility about 60 years ago. Thus no physical evidence remains of this historic facility and another important artifact from Canada's nuclear history has disappeared forever. It is planned to place a plaque at the site at some point in the future. (author)

Heavy water at Trail, British Columbia

Energy Technology Data Exchange (ETDEWEB)

Arsenault, J.E. [Ontario (Canada)

2006-09-15

Today Canada stands on the threshold of a nuclear renaissance, based on the CANDU reactor family, which depends on heavy water as a moderator and for cooling. Canada has a long history with heavy water, with commercial interests beginning in 1934, a mere two years after its discovery. At one time Canada was the world's largest producer of heavy water. The Second World War stimulated interest in this rather rare substance, such that the worlds largest supply (185 kg) ended up in Canada in 1942 to support nuclear research work at the Montreal Laboratories of the National Research Council. A year later commercial production began at Trail, British Columbia, to support work that later became known as the P-9 project, associated with the Manhattan Project. The Trail plant produced heavy water from 1943 until 1956, when it was shut down. During the war years the project was so secret that Lesslie Thomson, Special Liaison Officer reporting on nuclear matters to C.D. Howe, Minister of Munitions and Supply, was discouraged from visiting Trail operations. Thomson never did visit the Trail facility during the war. In 2005 the remaining large, tall concrete exchange tower was demolished at a cost of about $2.4 million, about the same as it cost to construct the facility about 60 years ago. Thus no physical evidence remains of this historic facility and another important artifact from Canada's nuclear history has disappeared forever. It is planned to place a plaque at the site at some point in the future. (author)

Chemistry in production of heavy water and industrial solvents

International Nuclear Information System (INIS)

Thomas, P.G.

2015-01-01

Industries are the temples of modern science built on the robust foundation of science and technology. The genesis of giant chemical industries is from small laboratories where the scientific thoughts are fused and transformed into innovative technologies Heavy water production is an energy intensive giant chemical industry where various hazardous and flammable chemicals are handled, extreme operating conditions are maintained and various complex chemical reactions are involved. Chemistry is the back bone to all chemical industrial activities and plays a lead role in heavy water production also. Heavy Water Board has now mastered the technology of design, construction, operation and maintenance of Heavy Water plants as well as fine tuning of the process make it more cost effective and environment friendly. Heavy Water Board has ventured into diversified activities intimately connected with our three stages of Nuclear Power Programme. Process development for the production of nuclear grade solvents for the front end and back end of our nuclear fuel cycle is one area where we have made significant contributions. Heavy Water Board has validated, modified and fine-tuned the synthesis routes for TBP, D2EHPA, TOPO, TAPO TIAP, DNPPA, D2EHPA-II, DHOA etc and these solvents were accepted by end users. Exclusive campaigns were carried out in laboratory scale, bench scale and pilot plant scale before scaling up to industrial scale. The process chemistry is understood very well and chemical parameters were monitored in every step of the synthesis. It is a continual improvement cycle where fine tuning is carried out for best quality and yield of product at lowest cost. In this presentation, an attempt is made to highlight the role of chemistry in the production of Heavy Water and industrial solvents

Method and apparatus for enrichment or upgrading heavy water

International Nuclear Information System (INIS)

Butler, J.P.; Hammerli, M.

1979-01-01

A method and apparatus for upgrading and final enrichment of heavy water are described, comprising means for contacting partially enriched heavy water feed in a catalyst column with hydrogen gas (essentially D 2 ) originating in an electrolysis cell so as to enrich the feed water with deuterium extracted from the electrolytic hydrogen gas and means for passing the deuterium enriched water to the electrolysis cell. (author)

The Canadian heavy water situation

International Nuclear Information System (INIS)

Dahlinger, A.

The Canadian heavy water industry is analyzed. Supply and demand are predicted through 1985. Pricing is broken down into components. Backup R and D contributes greatly to process improvements. (E.C.B.)

Tritium separation from heavy water using electrolysis

International Nuclear Information System (INIS)

Ogata, Y.; Sakuma, Y.; Ohtani, N.; Kodaka, M.

2001-01-01

A tritium separation from heavy water by the electrolysis using a solid polymer electrode (SPE) was specified on investigation. The heavy water (∼10 Bq g -1 ) and the light water (∼70 Bq g -1 ) were electrolysed using an electrolysis device (Tripure XZ001, Permelec Electrode Ltd.) with the SPE layer. The cathode was made of stainless steel (SUS314). The electrolysis was carried out at 20 A x 60 min, with the electrolysis temperature at 10, 20, or 30degC, and 15 A x 80 min at 5degC. The produced hydrogen and oxygen gases were recombined using a palladium catalyst (ND-101, N.E. Chemcat Ltd.) with nitrogen gas as a carrier. The activities of the water in the cell and of the recombined water were analyzed using a liquid scintillation counter. The electrolysis potential to keep the current 20 A was 2-3 V. The yields of the recombined water were more than 90%. The apparent separation factors (SF) for the heavy water and the light water were ∼2 and ∼12, respectively. The SF value was in agreement with the results in other work. The factors were changed with the cell temperature. The electrolysis using the SPE is applicable for the tritium separation, and is able to perform the small-scale apparatus at the room temperature. (author)

Improved method of degassing of feed water at Heavy Water Plant, Kota

International Nuclear Information System (INIS)

Krishnan, G.K.; Agrawal, A.K.

1994-01-01

Heavy Water Plant (Kota) processes 450 MT/hr of feed water as the source of deuterium using water/hydrogen sulphide exchange process for the production of heavy water. Plant design has limited the ingress of dissolved oxygen in feed water to 0.2 ppm. However, even this low limit on dissolved oxygen has been found unacceptable during plant operation as over an operational period of 3-4 years accumulation of sulphur due to oxidation of hydrogen sulphide on exchange tower trays poses major operational problems. This paper discusses the results of nitrogen injection used for reducing the ingress of dissolved oxygen in the feed water system of the plant. (author)

High resolution conductometry for isotopic assay of deuterium in mixtures of heavy water and light water

International Nuclear Information System (INIS)

Ananthanarayanan, R.; Sahoo, P.; Murali, N.

2014-01-01

A PC based high resolution conductivity monitoring technique has been deployed for determination of isotopic purity of heavy water in samples containing heavy water and light water mixtures using pulsating sensor based conductivity monitoring instrument. The technique involves accurate determination of conductivities of a series of specially treated heavy water and light water mixtures of various compositions at a constant solution temperature. The shift in conductivity (Δκ), which is the difference between conductivities of composite mixture after and before the formation of a typical complex compound (boric acid–mannitol complex in this case), shows a smooth and reproducible decreasing trend with increase in percentage composition of heavy water. This relation, which is obtained by appropriate calibration, is used in the software program for direct display of isotopic purity of heavy water. The technique is examined for determination of percentage composition of heavy water in the entire range of concentration (0-100 %) with reasonable precision (relative standard deviation, RSD ≤1.5 %). About 1 mL of sample is required for each analysis and analysis is completed within a couple of minutes after pretreatment of sample. The accuracy in measurement is ≤1.75 %. (author)

Canadian heavy water production - 1970 to 1980

International Nuclear Information System (INIS)

Galley, M.R.

1981-01-01

In the last decade, heavy water production in Canada has progressed from the commissioning of a single unit plant in Nova Scotia to a major production industry employing 2200 persons and operating three plants with an aggregate annual production capability in excess of 1800 Mg. The decade opened with an impending crisis in the supply of heavy water due to failure of the first Glace Bay Heavy Water Plant and difficulty in commissioning the second Canadian plant at Port Hawkesbury. Lessons learned at this latter plant were applied to the Bruce plant where the first two units were under construction. When the Bruce units were commissioned in 1973 the rate of approach to design production rates was much improved, renewing confidence in Canada's ability to succeed in large scale heavy water production. In the early 1970's a decision was made to rehabilitate the Glace Bay plant using a novel flowsheet and this rebuilt plant commenced production in 1976. The middle of the decade was marked by two main events: changes in ownership of the operating plants and initiation of a massive construction program to support the forecast of a rapidly expanding CANDU power station construction program. New production units embodying the best features of their predecessors were committed at Bruce by Ontario Hydro and at La Prade, Quebec, by AECL. The high growth rate in electrical demand did not continue and some new plant construction was curtailed. The present installed production capacity will now probably be adequate to meet anticipated demand for the next decade. Canadian plants have now produced more than 7800 Mg of heavy water at a commercially acceptable cost and with a high degree of safety and compliance with appropriate environmental regulations

Tritium concentration in the heavy water upgrading plants

International Nuclear Information System (INIS)

Croitoru, C.; Pop, F.; Titescu, Gh.; Dumitrescu, M.; Ciortea, C.; Stefanescu, I.; Peculea, M.; Pitigoi, Gh.; Trancota, D. . E-mail of corresponding author: croitoru@icsi.ro; Croitoru, C.)

2005-01-01

In the course of time heavy water used in CANDU nuclear power plants, as moderator or coolant, degrades, as a result of its impurification with light water and tritium. Concentration diminution below 99.8% mol for moderator and 99.75% mol for coolant causes an inefficient functioning of CANDU reactor. By isotopic distillation, light water is removed. Simultaneously tritium concentration takes place. The heavy water upgrading plant from Cernavoda is an isotopic separation cascade with two stages. The paper presents, for this plant, a theoretical study of the tritium concentration. (author)

Cell growth and protein synthesis of unicellular green alga Chlamydomonas in heavy water

International Nuclear Information System (INIS)

Ishida, M.R.

1983-01-01

The effects of heavy water on the cell growth and protein synthesis of the photoautotrophically growing Chlamydomonas cells were studied. The growth rate of the cells is inversely proportional to the concentrations of heavy water. The cells can barely live in 90% heavy water, but they die in 99.85% heavy water within a few days. Incorporation of 14 Cleucine into cells is markedly stimulated by heavy water of various concentrations between 30 and 99.85% in the case of the short time incubation. Contrary to this, in the long time incubation as several days, heavy water inhibits the protein synthesis. Such two modes of the protein synthetic activities are dependent upon the incubation time of the cells grown photoautotrophically in the heavy water media. (author)

High converter pressurized water reactor with heavy water as a coolant

International Nuclear Information System (INIS)

Ronen, Y.; Reyev, D.

1983-01-01

There is an increasing interest in water breeder and high converter reactors. The increase in the conversion ratio of these reactors is obtained by hardening the neutron spectrum achieved by tightening the reactor's lattice. Another way of hardening the neutron spectrum is to replace the light water with heavy water. Two pressurized water reactor fuel cycles that use heavy water as a coolant are considered. The first fuel cycle is based on plutonium and depleted uranium, and the second cycle is based on plutonium and enriched uranium. The uranium ore and separative work unit (SWU) requirements are calculated as well as the fuel cycle cost. The savings in uranium ore are about40 and 60% and about40% in SWU for both fuel cycles considered

Albedo-adjusted fast-neutron diffusion coefficients in reactor reflectors

International Nuclear Information System (INIS)

Terney, W.B.

1975-01-01

In the newer, larger pressurized-water reactor cores, the calculated power distributions are fairly sensitive to the number of neutron groups used and to the treatment of the reflector cross sections. Comparisons between transport and diffusion calculations show that the latter substantially underpredict the reflector albedos in the fast (top) group and that the power distribution is shifted toward the core center when compared to 4-group transport theory results. When the fast-neutron diffusion coefficients are altered to make the transport- and diffusion-theory albedos agree, the power distributions are also brought into agreement. An expression for the fast-neutron diffusion coefficients in reflector regions has been derived such that the diffusion calculation reproduces the albedo obtained from a transport solution. In addition, a correction factor for mesh effects applicable to coarse mesh problems is presented. The use of the formalism gives the correct albedos and improved power distributions. (U.S.)

Electromagnetic radiation during electrolysis of heavy water

International Nuclear Information System (INIS)

Koval'chuk, E.P.; Yanchuk, O.M.; Reshetnyak, O.V.

1994-01-01

The radiation in the visible and ultraviolet spectral regions during electrolysis of heavy water on nickel and palladium cathodes was determined for the first time. A sharp jump of the intensity photon flow was observed at a current density of higher than 125 mA/cm 2 . A hypothesis about the relation of the electrochemiluminescence phenomenon during electrolysis of heavy water with the formation of fresh surfaces in consequence of the hydrogenous corrosion of the cathode material is formulated. ((orig.))

Heavy metals in drinking water: Occurrences, implications, and future needs in developing countries

International Nuclear Information System (INIS)

Chowdhury, Shakhawat; Mazumder, M.A. Jafar; Al-Attas, Omar; Husain, Tahir

2016-01-01

Heavy metals in drinking water pose a threat to human health. Populations are exposed to heavy metals primarily through water consumption, but few heavy metals can bioaccumulate in the human body (e.g., in lipids and the gastrointestinal system) and may induce cancer and other risks. To date, few thousand publications have reported various aspects of heavy metals in drinking water, including the types and quantities of metals in drinking water, their sources, factors affecting their concentrations at exposure points, human exposure, potential risks, and their removal from drinking water. Many developing countries are faced with the challenge of reducing human exposure to heavy metals, mainly due to their limited economic capacities to use advanced technologies for heavy metal removal. This paper aims to review the state of research on heavy metals in drinking water in developing countries; understand their types and variability, sources, exposure, possible health effects, and removal; and analyze the factors contributing to heavy metals in drinking water. This study identifies the current challenges in developing countries, and future research needs to reduce the levels of heavy metals in drinking water. - Highlights: • Co-exposure to multiple heavy metals in drinking water needs better understanding • Low-cost technologies for arsenic removal needs urgent attention • Protonated alginate needs further research for drinking water applications • Community level and PoU devices need improvement and cost reduction • Developing countries are most affected by heavy metals in drinking water

Heavy metals in drinking water: Occurrences, implications, and future needs in developing countries

Energy Technology Data Exchange (ETDEWEB)

Chowdhury, Shakhawat, E-mail: Schowdhury@kfupm.edu.sa [Department of Civil and Environmental Engineering, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Mazumder, M.A. Jafar [Department of Chemistry, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Al-Attas, Omar [Department of Civil and Environmental Engineering, King Fahd University of Petroleum and Minerals, Dhahran 31261 (Saudi Arabia); Husain, Tahir [Faculty of Engineering and Applied Science, Memorial University of Newfoundland, St. John’s, NL (Canada)

2016-11-01

Heavy metals in drinking water pose a threat to human health. Populations are exposed to heavy metals primarily through water consumption, but few heavy metals can bioaccumulate in the human body (e.g., in lipids and the gastrointestinal system) and may induce cancer and other risks. To date, few thousand publications have reported various aspects of heavy metals in drinking water, including the types and quantities of metals in drinking water, their sources, factors affecting their concentrations at exposure points, human exposure, potential risks, and their removal from drinking water. Many developing countries are faced with the challenge of reducing human exposure to heavy metals, mainly due to their limited economic capacities to use advanced technologies for heavy metal removal. This paper aims to review the state of research on heavy metals in drinking water in developing countries; understand their types and variability, sources, exposure, possible health effects, and removal; and analyze the factors contributing to heavy metals in drinking water. This study identifies the current challenges in developing countries, and future research needs to reduce the levels of heavy metals in drinking water. - Highlights: • Co-exposure to multiple heavy metals in drinking water needs better understanding • Low-cost technologies for arsenic removal needs urgent attention • Protonated alginate needs further research for drinking water applications • Community level and PoU devices need improvement and cost reduction • Developing countries are most affected by heavy metals in drinking water.

Dynamics of large reflectors - Aerospatiale concepts

Science.gov (United States)

Flechais, A.; Picard, P.; Dauviau, C.; Truchi, C.

1992-08-01

An overview is presented of studies performed under an ESTEC contract and aimed at the identification of critical development areas of unfurlable reflectors and at the analysis of the dynamic interactions between reflectors and hosting spacecraft, in particular with respect to the design of the AOCS and antenna pointing mechanism (APM). Research and development performed by Aerospatiale since 1983 in the field of unfurlable mesh reflectors and supported by CNES are summarized. An analysis covering both the deployment phase and the deployed configuration is presented. The capabilities of classical AOCS and APM control laws for large reflectors are evaluated via simulations. It is shown that the baseline reflector under consideration is compatible with the PSDE mission and classical AOCS and APM control law designs.

Improved method of degassing of feed water at Heavy Water Plant, Kota

Energy Technology Data Exchange (ETDEWEB)

Krishnan, G K; Agrawal, A K [Heavy Water Plant, Kota (India)

1994-06-01

Heavy Water Plant (Kota) processes 450 MT/hr of feed water as the source of deuterium using water/hydrogen sulphide exchange process for the production of heavy water. Plant design has limited the ingress of dissolved oxygen in feed water to 0.2 ppm. However, even this low limit on dissolved oxygen has been found unacceptable during plant operation as over an operational period of 3-4 years accumulation of sulphur due to oxidation of hydrogen sulphide on exchange tower trays poses major operational problems. This paper discusses the results of nitrogen injection used for reducing the ingress of dissolved oxygen in the feed water system of the plant. (author). 1 fig.

Safety system in a heavy water detritiation plant

International Nuclear Information System (INIS)

Balteanu, O.; Stefan, I.; Retevoi, C.

2003-01-01

In a CANDU 6 type reactor a quantity of 55·10 15 Bq/year of tritium is generated, 95% being in the D 2 O moderator which can achieve a radioactivity of 2.5-3.5·10 12 Bq/kg. Tritium in heavy water contributes with 30-50% to the doses received by operation personnel and up to 20% to the radioactivity released in the environment. The large quantity of heavy water used in this type of reactors (500 tones) make storage very difficult, especially for environment. The extraction of tritium from tritiated heavy water of CANDU reactors solve the following problems: the radiation level in the operation area, the costs of maintenance and repair reduction due to reduction of personnel protection measures, the increase of NPP utilisation factor by shutdown time reduction for maintenance and repair, use the extracted tritium for fusion reactors and not for the last, lower costs and risk for storage heavy water waste. Heavy water detritiation methods, which currently are used in the industrial or experimental plant, are based on catalytic isotope exchange or electrolysis followed cryogenic distillation or permeation. The technology developed at Institute of Cryogenics and Isotope Separation is based upon catalytic exchange between tritiated water and deuterium, followed by cryogenic distillation of hydrogen isotopes. The nature of the fluids that are processed in detritiation requires the operation of the plant in safety conditions. The paper presents the safety system solution chose in order to solve this task, as well as a simulation of an incident and safety system response. The application software is using LabView platform that is specialised on control and factory automation applications. (author)

Modification of water treatment plant at Heavy Water Plant (Kota)

International Nuclear Information System (INIS)

Gajpati, C.R.; Shrivastava, C.S.; Shrivastava, D.C.; Shrivastava, J.; Vithal, G.K.; Bhowmick, A.

2008-01-01

Heavy Water Production by GS process viz. H 2 S - H 2 O bi-thermal exchange process requires a huge quantity of demineralized (DM) water as a source of deuterium. Since the deuterium recovery of GS process is only 18-19%, the water treatment plant (WTP) was designed and commissioned at Heavy Water Plant (Kota) to produce demineralized water at the rate of 680 m 3 /hr. The WTP was commissioned in 1980 and till 2005; the plant was producing DM water of required quality. It was having three streams of strong cation resin, atmospheric degasser and strong anion exchange resin with co-current regeneration. In 2001 a new concept of layered bed resin was developed and engineered for water treatment plant. The concept was attractive in terms of saving of chemicals and thus preservation of environment. Being an ISO 9000 and ISO 14000 plant, the modification of WTP was executed in 2005 during major turn around. After modification, a substantial amount of acid and alkali is saved

A review of the UKAEA interest in heavy water reactors

International Nuclear Information System (INIS)

Symes, R.J.

1983-01-01

The chapter commences with a brief account of the history of heavy water production and then begins the story of the British use of this moderator in power reactors. This is equated with the introduction and development of the tube reactor as a distinct and important form of reactor construction in contrast with the perhaps better known vessel design that has tended to dominate reactor engineering to date. The account thus includes a succession of reactor designs including the gas and steam cooled heavy water systems in addition to the steam-generating heavy water reactor. The SGHWR was demonstrated by the construction of a substantial prototype, which continues in operation as a flexible and reliable electricity-generating plant. It was also, for a time, identified as the system to be used for Britain's third reactor programme. Today the successful Canadian CANDU power reactors represent the only penetration of heavy water reactor technology into large scale electricity generation. The range of research and experimental reactors using heavy water in their cores is reviewed. (author)

Direction of Heavy Water Projects

International Nuclear Information System (INIS)

1984-07-01

Summary of the activities performed by the Heavy Water Projects Direction of the Argentine Atomic Energy Commission from 1950 to 1983. It covers: historical data; industrial plant (based on ammonia-hydrogen isotopic exchange); experimental plant (utilizing hydrogen sulfides-water process); Module-80 plant (2-3 tons per year experimental plant with national technology) and other related tasks on research and development (E.A.C.) [es

Handbook of reflector antennas and feed systems v.1 theory and design of reflectors

CERN Document Server

Sharma, Satish K; Shafai, Lotfollah

2013-01-01

This is the first truly comprehensive and most up-to-date handbook available on modern reflector antennas and feed sources for diversified space and ground applications. There has never been such an all-encompassing reflector handbook in print, and no currently available title offers coverage of such recent research developments. The Handbook consists of three volumes. Volume I provides a unique combination of theoretical underpinnings with design considerations and techniques. The need for knowledge in reflector antennas has grown steadily over the last two decades due to increased use in spa

Thorium in heavy water reactors

International Nuclear Information System (INIS)

Andersson, G.

1984-12-01

Advanced heavy water reactors can provide energy on a global scale beyond the foreseeable future. Their economic and safety features are promising: 1. The theoretical feasibility of the Self Sufficient Equilibrium Thorium (SSET) concept is confirmed by new calculations. Calculations show that the adjuster rod geometry used in natural uranium CANDU reactors is adequate also for SSET if the absorption in the rods is graded. 2. New fuel bundle designs can permit substantially higher power output from a CANDU reactor. The capital cost for fuel, heavy water and mechanical equipment can thereby be greatly reduced. Progress is possible with the traditional fuel material oxide, but the use of thorium metal gives much larger effects. 3. A promising long range possibility is to use pressure tanks instead of pressure tubes. Heat removal from the core is facilitated. Negative temperature and void coefficients provide inherent safety features. Refuelling under power is no longer needed if control by moderator displacement is used. Reduced quality demand on the fuel permits lower fuel costs. The neutron economy is improved by the absence of pressure and clandria tubes and also by the use of radial and axial blankets. A modular seed blanket design can reduce the Pa losses. The experience from construction of tank designs is good e.g. AAgesta, Attucha. It is now also possible to utilize technology from LWR reactors and the implementation of advanced heavy water reactors would thus be easier than HTR or LMFBR systems. (Author)

Decontamination of the RA reactor heavy water system, Annex 9

International Nuclear Information System (INIS)

Maksimovic, Z.B.; Nikolic, R.M.; Marinkovic, M.D.; Jelic, Lj.M.

1963-01-01

Both stainless steel and aluminium parts of the RA reactor heavy water system system were decontaminated as well as the heavy water itself. System was contaminated with 60 Co. Decontamination factor was determined by activity measurements during distillation. Concentration of the corrosion products in the heavy water was measured by spectrochemical analysis, and found to be 0.1 - 1 mg/l. Chemical analyses of the aluminium and stainless steel surfaces showed that cobalt was adsorbed on the aluminium oxide layer. Water solution of 7%H 3 PO 4 + 2% CrO 3 was used for decontamination of the heavy water system and distillation device. This was found to be the most efficient solvent which does not affect stainless steel corrosion. Decontamination factors achieved were from 60 - 100. Decontamination results enabled determining the distribution of cobalt in the system: 10 Ci on the stainless steel parts, 50 Ci in the heavy water; and above 600 Ci on the fuel and experimental channels. Specific activity of 60 Co was calculated to be 15 Ci/g on the reactor channels, 8 Ci/g on the stainless steel parts and 3 Ci/g in the heavy water. Decontamination of the aluminium parts was not done because it was considered it could initiate corrosion. Since the efficiency of distillation is increased it was expected that permanent distillation would remove most of the activity in the reactor channels

Heavy Metals Pollution on Surface Water Sources in Kaduna ...

African Journals Online (AJOL)

This study examine the effects of heavy metal pollutants to aquatic ecosystems and the environment by considering the role of urban, municipal, agricultural, industrial and other anthropogenic processes as sources of heavy metal pollution in surface water sources of Kaduna metropolis. Samples of the polluted water were ...

Consequences of potential accidents in heavy water plants

International Nuclear Information System (INIS)

Croitoru, C.; Lazar, R.E.; Preda, I.A.; Dumitrescu, M.

2002-01-01

Heavy water plants achieve the primary isotopic concentration by H 2 O-H 2 S chemical exchange. In these plants are stored large quantities of hydrogen sulphide (high toxic, corrosive, flammable and explosive) maintained in process at relative high temperatures and pressures. It is required an assessment of risks associated with the potential accidents. The paper presents adopted model for quantitative consequences assessment in heavy water plants. Following five basic steps are used to identify the risks involved in plants operation: hazard identification, accident sequences development, H 2 S emissions calculus, dispersion analyses and consequences determination. A brief description of each step and some information from risk assessment for our heavy water pilot plant are provided. Accident magnitude, atmospheric conditions and population density in studied area were accounted for consequences calculus. (author)

Heavy metals in drinking water: Occurrences, implications, and future needs in developing countries.

Science.gov (United States)

Chowdhury, Shakhawat; Mazumder, M A Jafar; Al-Attas, Omar; Husain, Tahir

2016-11-01

Heavy metals in drinking water pose a threat to human health. Populations are exposed to heavy metals primarily through water consumption, but few heavy metals can bioaccumulate in the human body (e.g., in lipids and the gastrointestinal system) and may induce cancer and other risks. To date, few thousand publications have reported various aspects of heavy metals in drinking water, including the types and quantities of metals in drinking water, their sources, factors affecting their concentrations at exposure points, human exposure, potential risks, and their removal from drinking water. Many developing countries are faced with the challenge of reducing human exposure to heavy metals, mainly due to their limited economic capacities to use advanced technologies for heavy metal removal. This paper aims to review the state of research on heavy metals in drinking water in developing countries; understand their types and variability, sources, exposure, possible health effects, and removal; and analyze the factors contributing to heavy metals in drinking water. This study identifies the current challenges in developing countries, and future research needs to reduce the levels of heavy metals in drinking water. Copyright © 2016 Elsevier B.V. All rights reserved.

Water conservation by 3 R's - case histories of Heavy Water Plants

International Nuclear Information System (INIS)

Agarwal, A.K.; Hiremath, S.C.

2005-01-01

The basics of water conservation revolve around three R's of Reduce, Recycle, and Reuse. The Heavy Water Plants are an excellent example of water savings, and these case studies will be of interest to the chemical industry. The issues involved with water conservation and re-use in different Heavy Water Plants are of different nature. In H 2 S-H 2 O process plants the water consumption has been substantially decreased as compared to the design water needs. To quote the figures HWP (Kota) was designed to consume 2280 m 3 /hr water, which included 453 m 3 /hr water as feed for deuterium extraction. Today the plant operates with only 1250 m 3 /hr water while processing 500 m 3 /hr feed; and is headed to decrease the total water consumption to 700 m 3 /hr. Similarly at HWP (Manuguru) the design had provided 5600 m 3 /hr water consumption, which is today operating with only 1750 m 3 /hr and poised to operate with 1600 m 3 /hr. The issues of water conservation in Ammonia Hydrogen exchange plants have an additional dimension since water losses mean direct loss of heavy water production. In adjoining ammonia plants deuterium shifts to steam in the reformer and shift converter, and this excess steam is condensed as rich condensate. It becomes incumbent on the fertilizer plant to maintain a tight discipline for conserving and re-using the rich condensate so that deuterium concentration in the synthesis gas is maintained. Efforts are also underway to utilize rich condensate of GSFC in the newly developed technology of water ammonia exchange at HWP (Baroda) and we are targeting 20% production gains by implementation of this scheme and with no increase in the pollution load. These case histories will be of interest to Chemical Process Industry. (author)

Possibilities for reorientation the activity of heavy water plants

International Nuclear Information System (INIS)

Pop, F.; Croitoru, C.; Titescu, Gh.; Stefanescu, I.; Hodor, I.; Cuna, S. . E-mail of corresponding author: pop.floarea@icsi.ro; Pop, F.)

2005-01-01

In Romania heavy water is produced by H 2 O-H 2 S chemical exchange (GS process) and by water distillation, simultaneously working two lines. The distillation plants have high separation capacity, a distillation line being able to concentrate water from two GS lines. The paper presents data regarding possibilities to use one distillation line for oxygen 18 production, as pre-concentrates or finite products. Using a simulation program it was calculated oxygen 18 concentration in heavy water produced, maximum 18 O concentration of pre-concentrate obtained on distillation line and the separation cascade dimensions for obtain 95% 18 O, with first and second stage having same dimensions like a distillation plant from Romanian heavy water factory. Oxygen-18 separation factor is much lower than deuterium separation factor. For this reason, oxygen-18 is a very expensive product. (author)

Determination of selected heavy metals in inland fresh water of ...

African Journals Online (AJOL)

Agadaga

Key words: Heavy metals, freshwater, concentrations, quality, variation, distribution. ... prevalence of heavy metals in inland water of lower River. Niger drain are scarce ..... Niger waters at Ajaokuta were found to be low and within guideline.

SAFARI-1 research reactor beryllium reflector element replacement, management and relocation

International Nuclear Information System (INIS)

Kock, Marisa De; Vlok, Jwh; Steynberg, B.J.

2012-01-01

The beryllium (Be) reflector elements of the SAFARI-1 Research Reactor were replaced in October 2011 as part of the Ageing Management Programme of the reactor. After more than three million MWh of operation over a period of 47 years, core reloading became more difficult due to the geometric deformation of the beryllium reflector elements. During the replacement of the reflector elements, criticality and reactivity worth experiments were performed and found to compare favorably with calculated values. A Beryllium Management Programme was established at SAFARI-1 to identify and apply effective and appropriate actions and practices for managing the ageing of the new beryllium reflector elements. This will provide timely detection and mitigation of ageing mechanisms relevant to beryllium reflector elements, supporting the life extension of these elements. These actions and practices include monitoring of the tritium levels in the primary water, calculating and measuring the fluxes within the beryllium reflector positions, measuring the straightness of the elements to track geometric deformation and visually inspecting the reflector elements for crack formation. Acceptance criteria indicating the end of life of the elements were established. These criteria take into account the smallest gap that could exist between elements, sudden changes in the tritium levels and formation of cracks. All the data obtained through the Beryllium Management Programme are recorded in a database. Additional benefits gained through a Beryllium Management Programme are the availability of a complete irradiation history of the beryllium reflector elements at any point in time and the establishment of a knowledge base to assists in the understanding of the behavior of the beryllium reflector elements in an irradiation environment. Straightness baseline measurements of the new beryllium reflector elements were performed with a beryllium straightness measurement tool, designed at SAFARI-1. The

SAFARI-1 research reactor beryllium reflector element replacement, management and relocation

Energy Technology Data Exchange (ETDEWEB)

Kock, Marisa De; Vlok, Jwh; Steynberg, B J [South Africa Atomic Energy Corporation (Necsa) (South Africa)

2012-03-15

The beryllium (Be) reflector elements of the SAFARI-1 Research Reactor were replaced in October 2011 as part of the Ageing Management Programme of the reactor. After more than three million MWh of operation over a period of 47 years, core reloading became more difficult due to the geometric deformation of the beryllium reflector elements. During the replacement of the reflector elements, criticality and reactivity worth experiments were performed and found to compare favorably with calculated values. A Beryllium Management Programme was established at SAFARI-1 to identify and apply effective and appropriate actions and practices for managing the ageing of the new beryllium reflector elements. This will provide timely detection and mitigation of ageing mechanisms relevant to beryllium reflector elements, supporting the life extension of these elements. These actions and practices include monitoring of the tritium levels in the primary water, calculating and measuring the fluxes within the beryllium reflector positions, measuring the straightness of the elements to track geometric deformation and visually inspecting the reflector elements for crack formation. Acceptance criteria indicating the end of life of the elements were established. These criteria take into account the smallest gap that could exist between elements, sudden changes in the tritium levels and formation of cracks. All the data obtained through the Beryllium Management Programme are recorded in a database. Additional benefits gained through a Beryllium Management Programme are the availability of a complete irradiation history of the beryllium reflector elements at any point in time and the establishment of a knowledge base to assists in the understanding of the behavior of the beryllium reflector elements in an irradiation environment. Straightness baseline measurements of the new beryllium reflector elements were performed with a beryllium straightness measurement tool, designed at SAFARI-1. The

Development and implementation of the heavy water program at Bruce Power

International Nuclear Information System (INIS)

Davloor, R.; Bourassa, C.

2014-01-01

Bruce Power operates 8 pressurized heavy water reactor units requiring more than 6000 mega grams (Mg) of heavy water. A Heavy Water Management Program that has been developed to administer this asset over the past 3 years. Through a corporate management system the Program provides governance, oversight and support to the stations. It is implemented through organizational structure, program and procedure documents and an information management system that provides benchmarked metrics, business intelligence and analytics for decision making and prediction. The program drives initiatives such as major maintenance activities, capital programs, detritiation strategies and ensures heavy water systems readiness for outages and rehabilitation of units. (author)

Development and implementation of the heavy water program at Bruce Power

Energy Technology Data Exchange (ETDEWEB)

Davloor, R.; Bourassa, C., E-mail: ram.davloor@brucepower.com, E-mail: carl.bourassa@brucepower.com [Bruce Power, Tiverton, ON (Canada)

2014-07-01

Bruce Power operates 8 pressurized heavy water reactor units requiring more than 6000 mega grams (Mg) of heavy water. A Heavy Water Management Program that has been developed to administer this asset over the past 3 years. Through a corporate management system the Program provides governance, oversight and support to the stations. It is implemented through organizational structure, program and procedure documents and an information management system that provides benchmarked metrics, business intelligence and analytics for decision making and prediction. The program drives initiatives such as major maintenance activities, capital programs, detritiation strategies and ensures heavy water systems readiness for outages and rehabilitation of units. (author)

Possibilities for reorientation of activity in Heavy Water Plants

International Nuclear Information System (INIS)

Pop, F.; Croitoru, C.; Titescu, Gh.; Stefanescu, I.; Hodor, I.; Cuna, S.

2004-01-01

In Romania heavy water is produced by H 2 O-H 2 S chemical exchange (GS process) and by water distillation, in two lines working simultaneously. The distillation plants have high separation capacity, a distillation line being able to concentrate water from two GS lines. The paper presents data regarding possibilities to use one distillation line for oxygen - 18 production, as pre-concentrates or finite products. A simulation program was used to calculate the oxygen - 18 concentration in the heavy water produced, maximum 18 O concentration of pre-concentrate obtained on distillation line and the separation cascade sizes to obtain 95% 18 O, with first and second stage having the same sizes like the distillation plant from the Romanian heavy water factory. Oxygen-18 separation factor is much lower than deuterium separation factor. For this reason, oxygen-18 is a very expensive product. (authors)

Study of the heavy water regeneration processes; Studija procesa za regeneraciju teske vode

Energy Technology Data Exchange (ETDEWEB)

Cavcic, E [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Yugoslavia)

1965-11-15

Experience derived from heavy water reactor operation showed degradation and dilution of heavy water to be inevitable depends on the type of reactor. Dilution of heavy water during operation of the RA and the RB reactors is shown in this report. Principles and procedures of heavy water regeneration by electrolysis, fractional distillation, cleaning, prevention of tritium contamination are described as well as separation columns.

Optimization of Surrounding Reflector Material for Hyb-WT

International Nuclear Information System (INIS)

Tariq Siddique, M.; Hong, Song Hee; Kim, Myung Hyun

2013-01-01

The choice of reflector material is crucial for fusion and hybrid reactors as it was for the fission reactors. Multiple reflector materials were studied for pure fusion blanket design. The purpose of reflector in fusion blanket is to enhance the tritium breeding ratio (TBR). In fusion fission hybrid blanket the roll of reflector is slightly changed as it include the fission core and the performance of fission core also needs to be optimized and evaluated with the choice of reflector material, along with the enhancement of TBR. The performance parameters of Hyb-WT are significantly influenced by the choice of reflector material. TiC is best for TRU transmutation, TBR and reduced the neutron wall loading and graphite is best for FP transmutation. Strategy of multi reflector materials gives the best TRU and FP transmutation performance and also enhanced TBR with reduced neutron wall loading and it is a better choice for Hyb-WT reflector. The neutron flux is primarily dominated by the fission neutrons

Energy conservation and management strategies in Heavy Water Plants

International Nuclear Information System (INIS)

Kamath, H.S.

2002-01-01

In the competitive industrial environment it is essential that cost of the product is kept at the minimum possible. Energy conservation is an important aspect in achieving this as energy is one of the key recourses for growth and survival of industry. The process of heavy water production being very complex and energy intensive, Heavy Water board has given a focussed attention for initiating various measures for reducing the specific energy consumption in all the plants. The initiative resulted in substantial reduction in specific energy consumption and brought in savings in cost. The cumulative reduction of specific energy consumption has been over 30% over the last seven years and the total savings for the last three years on account of the same has been about Rs. 190 crore. The paper describes the strategies adopted in the heavy water plants for effecting the above achievements. The paper covers the details of some of the energy saving schemes carried out at different heavy water plants through case studies. The case studies of schemes implemented at HWPs are general in nature and is applicable for any other industry. The case studies cover the modifications with re-optimisation of the process parameters, improvements effected in utility units like refrigeration and cooling water systems, improvements in captive power plant cycle and improved recycle scheme for water leading to reduced consumptions. The paper also mentions the innovative ammonia absorption refrigeration with improved coefficient of performance and HWB's efforts in development of the system as an integrated unit of the ammonia water deuterium exchange process for heavy water production. HWB also has taken up R and D on various other schemes for improvements in energy consumption for future activities covering utilisation of low grade energy for generation of refrigeration. (author)

Monte Carlo simulation of moderator and reflector in coal analyzer based on a D-T neutron generator.

Science.gov (United States)

Shan, Qing; Chu, Shengnan; Jia, Wenbao

2015-11-01

Coal is one of the most popular fuels in the world. The use of coal not only produces carbon dioxide, but also contributes to the environmental pollution by heavy metals. In prompt gamma-ray neutron activation analysis (PGNAA)-based coal analyzer, the characteristic gamma rays of C and O are mainly induced by fast neutrons, whereas thermal neutrons can be used to induce the characteristic gamma rays of H, Si, and heavy metals. Therefore, appropriate thermal and fast neutrons are beneficial in improving the measurement accuracy of heavy metals, and ensure that the measurement accuracy of main elements meets the requirements of the industry. Once the required yield of the deuterium-tritium (d-T) neutron generator is determined, appropriate thermal and fast neutrons can be obtained by optimizing the neutron source term. In this article, the Monte Carlo N-Particle (MCNP) Transport Code and Evaluated Nuclear Data File (ENDF) database are used to optimize the neutron source term in PGNAA-based coal analyzer, including the material and shape of the moderator and neutron reflector. The optimized targets include two points: (1) the ratio of the thermal to fast neutron is 1:1 and (2) the total neutron flux from the optimized neutron source in the sample increases at least 100% when compared with the initial one. The simulation results show that, the total neutron flux in the sample increases 102%, 102%, 85%, 72%, and 62% with Pb, Bi, Nb, W, and Be reflectors, respectively. Maximum optimization of the targets is achieved when the moderator is a 3-cm-thick lead layer coupled with a 3-cm-thick high-density polyethylene (HDPE) layer, and the neutron reflector is a 27-cm-thick hemispherical lead layer. Copyright © 2015 Elsevier Ltd. All rights reserved.

Conceptual designing of reduced-moderation water reactor with heavy water coolant

Energy Technology Data Exchange (ETDEWEB)

Hibi, Kohki; Shimada, Shoichiro; Okubo, Tsutomu E-mail: okubo@hems.jaeri.go.jp; Iwamura, Takamichi; Wada, Shigeyuki

2001-12-01

The conceptual designing of reduced-moderation water reactors, i.e. advanced water-cooled reactors using plutonium mixed-oxide fuel with high conversion ratios more than 1.0 and negative void reactivity coefficients, has been carried out. The core is designed on the concept of a pressurized water reactor with a heavy water coolant and a triangular tight lattice fuel pin arrangement. The seed fuel assembly has an internal blanket region inside the seed fuel region as well as upper and lower blanket regions (i.e. an axial heterogeneous core). The radial blanket fuel assemblies are introduced in a checkerboard pattern among the seed fuel assemblies (i.e. a radial heterogeneous core). The radial blanket region is shorter than the seed fuel region. This study shows that the heavy water moderated core can achieve negative void reactivity coefficients and conversion ratios of 1.06-1.11.

Measuring device for bending of beryllium reflector

International Nuclear Information System (INIS)

Nishida, Seiri; Sakamoto, Naoki.

1994-01-01

The device of the present invention can measure bending of a beryllium reflector formed in a reactor core of a nuclear reactor by a relatively easy operation. Namely, a sensor portion comprises a long-support that can be inserted to a fuel element-insertion hole disposed in the reactor and a plurality of distance sensors disposed in a longitudinal direction of the support. A supersonic wave sensor which is advantageous in the heat resistance, the size and the accuracy and can conduct measurement in water relatively easily is used as the distance sensors. However, other sensors, instead of the sensor described above, may also be used. The plurality of distance sensors detect the bending amount of the beryllium reflector in the longitudinal direction by such an easy operation of inserting such a sensor portion to the fuel element-insertion hole upon exchange of fuel elements. (I.S.)

WWER radial reflector modeling by diffusion codes

International Nuclear Information System (INIS)

Petkov, P. T.; Mittag, S.

2005-01-01

The two commonly used approaches to describe the WWER radial reflectors in diffusion codes, by albedo on the core-reflector boundary and by a ring of diffusive assembly size nodes, are discussed. The advantages and disadvantages of the first approach are presented first, then the Koebke's equivalence theory is outlined and its implementation for the WWER radial reflectors is discussed. Results for the WWER-1000 reactor are presented. Then the boundary conditions on the outer reflector boundary are discussed. The possibility to divide the library into fuel assembly and reflector parts and to generate each library by a separate code package is discussed. Finally, the homogenization errors for rodded assemblies are presented and discussed (Author)

Design of optically stable image reflector system.

Science.gov (United States)

Tsai, Chung-Yu

2013-08-01

The design of a partially optically stable (POS) reflector system, in which the exit ray direction and image pose are unchanged as the reflector system rotates about a specific directional vector, was presented in an earlier study by the current group [Appl. Phys. B100, 883-890 (2010)]. The present study further proposes an optically stable image (OSI) reflector system, in which not only is the optical stability property of the POS system retained, but the image position and total ray path length are also fixed. An analytical method is proposed for the design of OSI reflector systems comprising multiple reflectors. The validity of the proposed approach is demonstrated by means of two illustrative examples.

16 CFR 1512.16 - Requirements for reflectors.

Science.gov (United States)

2010-01-01

... 1512.16 Commercial Practices CONSUMER PRODUCT SAFETY COMMISSION FEDERAL HAZARDOUS SUBSTANCES ACT... vehicle headlamps. The use of reflector combinations off the center plane of the bicycle (defined in...) Front reflector. The reflector or mount shall not contact the ground plane when the bicycle is resting...

Pyramidal-Reflector Solar Heater

Science.gov (United States)

1982-01-01

Motor-driven reflector compensates for seasonal changes in Sun's altitude. System has flat-plate absorbers mounted on north side of attic interior. Skylight window on south-facing roof admits Sunlight into attic, lined with mirrors that reflect light to absorbers. Reflectors are inner surfaces of a pyramid lying on its side with window at its base and absorber plates in a cross-sectional plane near its apex.

The upgrade of intense pulsed neutron source (IPNS) through the change of coolant and reflector

CERN Document Server

Baek, I C; Iverson, E B

2002-01-01

The current intense pulsed neutron source (IPNS) depleted uranium target is cooled by light water. The inner reflector material is graphite and the outer reflector material is beryllium. The presence of H sub 2 O in the target moderates neutrons and leads to a higher absorption loss in the target than is necessary. D sub 2 O coolant in the small quantities required minimizes this effect. We have studied the possible improvement in IPNS beam fluxes that would result from changing the coolant from H sub 2 O to D sub 2 O and the inner reflector from graphite to beryllium. Neutron intensities were calculated for directions normal to the viewed surface of each moderator for four different cases of combinations of target coolant and reflector materials. The simulations reported here were performed using the MCNPX (version 2.1.5) computer program. Our results show that substantial gains in neutron beam intensities can be achieved by appropriate combination of target coolant and reflector materials. The combination o...

Conceptual design of a large heavy water reactor for US siting

International Nuclear Information System (INIS)

Shapiro, N.L.; Jesick, J.F.

1979-09-01

Information is presented concerning fuel management and safety and licensing assessment of the pressurized heavy water reactor; and commercial introduction of the pressurized heavy water reactor in the United States

76 FR 52994 - Application for a License To Export Heavy Water

Science.gov (United States)

2011-08-24

... NUCLEAR REGULATORY COMMISSION Application for a License To Export Heavy Water Pursuant to 10 CFR... (liters). producing an active water). pharmaceutical ingredient known as CTP-499, which incorporates heavy water as the source of deuterium to achieve the hydrogen-deuterium exchange. November 30, 2010 December...

Lamp with a truncated reflector cup

Science.gov (United States)

Li, Ming; Allen, Steven C.; Bazydola, Sarah; Ghiu, Camil-Daniel

2013-10-15

A lamp assembly, and method for making same. The lamp assembly includes first and second truncated reflector cups. The lamp assembly also includes at least one base plate disposed between the first and second truncated reflector cups, and a light engine disposed on a top surface of the at least one base plate. The light engine is configured to emit light to be reflected by one of the first and second truncated reflector cups.

Spatiotemporal Analysis of Heavy Metal Water Pollution in Transitional China

Directory of Open Access Journals (Sweden)

Huixuan Li

2015-07-01

Full Text Available China’s socioeconomic transitions have dramatically accelerated its economic growth in last three decades, but also companioned with continuous environmental degradation. This study will advance the knowledge of heavy metal water pollution in China from a spatial–temporal perspective. Specifically, this study addressed the following: (1 spatial patterns of heavy metal water pollution levels were analyzed using data of prefecture-level cities from 2004 to 2011; and (2 spatial statistical methods were used to examine the underlying socioeconomic and physical factors behind water pollution including socioeconomic transitions (industrialization, urbanization, globalization and economic development, and environmental characteristic (natural resources, hydrology and vegetation coverage. The results show that only Cr pollution levels increased over the years. The individual pollution levels of the other four heavy metals, As, Cd, Hg, and Pb, declined. High heavy metal water pollution levels are closely associated with both anthropogenic activities and physical environments, in particular abundant mineral resources and industrialization prosperity. On the other hand, economic development and urbanization play important roles in controlling water pollution problems. The analytical findings will provide valuable information for policy-makers to initiate and adjust protocols and strategies for protecting water sources and controlling water pollution; thus improving the quality of living environments.

Apparatus including concave reflectors and a line of optical fibers

International Nuclear Information System (INIS)

Dolan, J.T.

1992-01-01

This patent describes an apparatus including a radiation source which emits in a multiplicity of directions for focusing radiation on an object which may receive radiation within a certain solid angle. It comprises a first reflector and a second reflector, the first reflector being elliptical in cross section and having a first focus and a second focus, the second reflector being circular in cross section and having a center, and a radius equal to the distance between the second reflector and the first focus, the first reflector and the second reflector being arranged so that a concave reflecting surface of the first reflector faces a concave reflecting surface of the second reflector, and so arranged that the first focus of the first reflector corresponds to the center of the second reflector, the radiation source being an elongated discharge bulb, the object being a group of two or more optical fibers defining at least one line of optical fibers which are located at the second focus of the first reflector

Extending the product variety at ROMAG-PROD Heavy Water Plant

International Nuclear Information System (INIS)

Preda, M.; Patrascu, M.; Achimescu, D.; Stroia, A.

2004-01-01

Full text: Having in mind that the prospects of operating the ROMAG-PROD Heavy Water Plant are conditioned by both the heavy water market demand and the wear of the equipment which is exposed to hydrogen sulfide-induced corrosion, some possibilities were considered to extend the assortment of products, the production of which could ensure the plant's operation on long term. The proposals here refer to promoting the efficient production of oxygen-isotope-based products which would optimize maximally the exploit of available raw materials, supply and utilities of the ROMAG compound. The market manifests a significant demand of water enriched in the 18 O isotope up to 95-97% purity that is used in Positron Emission Tomography (PET). This oxygen isotope is also used as a labelling agent in studies of reaction mechanisms and paleo-climatologic studies as well. Some research evidenced the superconducting properties of some oxygen compounds containing the 18 O isotope. The isotope 17 O has applications in Nuclear Magnetic Resonance (NMR) as being the sole oxygen isotope endowed with a nuclear magnetic moment. On the other hand, it was found that although the 16 O isotope has a natural abundance of 99.8%, applications exist that require the absolute purity of this isotope i.e. the elimination of the other oxygen isotopes as is the case of fission reactors with Plutonium dioxide as nuclear fuel. The methods applied on industrial scale for enriching the oxygen isotopes are based on distillation of some oxygen compounds such as water and nitrogen monoxide. The possibility of a supplementary distillation of the heavy water at a distillation line of ROMAG-PROD Heavy Water Plant was considered in order to enrich the heavy water in the 17 O and 18 O isotopes up to an upper limit of 2-5% for 18 O. Obtaining the heavy isotopes of oxygen by distillation of heavy water is characterized by several aspects as the following ones: a high specific consumption of steam due to both the low

Cooling water treatment for heavy water project (Paper No. 6.9)

International Nuclear Information System (INIS)

Valsangkar, H.N.

1992-01-01

With minor exceptions, water is the preferred industrial medium for the removal of unwanted heat from process systems. The application of various chemical treatments is required to protect the system from water related and process related problems of corrosion, scale and deposition and biofouling. The paper discusses the cooling water problems for heavy water industries along with the impact caused by associated fertilizer units. (author). 6 figs

Heavy water technology and its contribution to energy sustainability

International Nuclear Information System (INIS)

MacDiarmid, H.; Alizadeh, A.; Hopwood, J.; Duffey, R.

2009-01-01

Full text: As the global nuclear industry expands several markets are exploring avenues and technologies to underpin energy security. Heavy water reactors are the most versatile power reactors in the world. They have the potential to extend resource utilization significantly, to allow countries with developing industrial infrastructures access to clean and abundant energy, and to destroy long-lived nuclear waste. These benefits are available by choosing from an array of possible fuel cycles. Several factors, including Canada's early focus on heavy-water technology, limited heavy-industry infrastructure at the time, and a desire for both technological autonomy and energy self-sufficiency, contributed to the creation of the first commercial heavy water reactor in 1962. With the maturation of the industry, the unique design features of the now-familiar product-on-power refuelling, high neutron economy, and simple fuel design-make possible the realization of its potential fuel-cycle versatility. As resource constrains apply pressure on world markets, the feasibility of these options have become more attractive and closer to entering widespread commercial application

HEAVY METALS AS UNWANTED COMPONENTS OF BACKWASH WATER DERIVED FROM GROUNDWATER TREATMENT

Directory of Open Access Journals (Sweden)

Robert Nowak

2016-06-01

Full Text Available The paper presents some aspects of the problem of heavy metals presence in wastewater and sewage sludge from water treatment. In the first part, issues on quality of wastewaters and sludge produced during water treatment along with actions aimed at the neutralization of such wastes, were discussed. Subsequent parts of the work present the example of 12 groundwater treatment stations in a particular municipality, and the problem of backwash water quality, in particular, heavy metals contents. The analysis covered a period of three years: 2013, 2014, and 2015. The authors, using the discussed examples, have shown that besides hydrated iron and manganese oxides, also other toxic contaminants can be present in backwash water from groundwater treatment. In particular, the qualitative analysis of the backwash water revealed the presence of heavy metals, mainly zinc. The test results for backwash water were compared with those of filtrate qualitative assessment, wherein the heavy metals were not found. This fact indicated the metal retention in the filter bed and their unsustainable immobilization resulting in penetration of heavy metals from deposit to the backwash water along with other impurities, mainly iron and manganese oxides. The main conclusion from the study is to demonstrate the need for constant monitoring of the backwash water quality, including the presence of toxic heavy metals. This is also important because of the requirement to minimize the negative environmental impact of wastes generated during the water treatment process.

"Periodic-table-style" paper device for monitoring heavy metals in water.

Science.gov (United States)

Li, Miaosi; Cao, Rong; Nilghaz, Azadeh; Guan, Liyun; Zhang, Xiwang; Shen, Wei

2015-03-03

If a paper-based analytical device (μ-PAD) could be made by printing indicators for detection of heavy metals in chemical symbols of the metals in a style of the periodic table of elements, it could be possible for such μ-PAD to report the presence and the safety level of heavy metal ions in water simultaneously and by text message. This device would be able to provide easy solutions to field-based monitoring of heavy metals in industrial wastewater discharges and in irrigating and drinking water. Text-reporting could promptly inform even nonprofessional users of the water quality. This work presents a proof of concept study of this idea. Cu(II), Ni(II), and Cr(VI) were chosen to demonstrate the feasibility, specificity, and reliability of paper-based text-reporting devices for monitoring heavy metals in water.

Canned motor pumps at Heavy Water Project, Baroda

International Nuclear Information System (INIS)

Batra, R.K.; Waishampayan, S.C.

1981-01-01

Pumps to be used in heavy water plants must be reliable and should require negligible maintenance, because most of them are totally unapproachable under normal circumstances. Canned motor pumps fulfil these requirements. Their design features are described briefly. The details of: (1) the pumps in the isotopic exchange tower and (2) pumps for liquid ammonia and catalyst are given. Problems faced during commissioning of such pumps in Baroda Heavy Water Project were bulging of rotors of tower pumps, bulging of stators, jamming and failure of bearings. Solution of these problems is described. (M.G.B.)

Reflector modelization for neutronic diffusion and parameters identification

International Nuclear Information System (INIS)

Argaud, J.P.

1993-04-01

Physical parameters of neutronic diffusion equations can be adjusted to decrease calculations-measurements errors. The reflector being always difficult to modelize, we choose to elaborate a new reflector model and to use the parameters of this model as adjustment coefficients in the identification procedure. Using theoretical results, and also the physical behaviour of neutronic flux solutions, the reflector model consists then in its replacement by boundary conditions for the diffusion equations on the core only. This theoretical result of non-local operator relations leads then to some discrete approximations by taking into account the multiscaled behaviour, on the core-reflector interface, of neutronic diffusion solutions. The resulting model of this approach is then compared with previous reflector modelizations, and first results indicate that this new model gives the same representation of reflector for the core than previous. (author). 12 refs

Reflector-moderated critical assemblies

International Nuclear Information System (INIS)

Paxton, H.C.; Jarvis, G.A.; Byers, C.C.

1975-07-01

Experiments with reflector-moderated critical assemblies were part of the Rover Program at the Los Alamos Scientific Laboratory (LASL). These assemblies were characterized by thick D 2 O or beryllium reflectors surrounding large cavities that contained highly enriched uranium at low average densities. Because interest in this type of system has been revived by LASL Plasma Cavity Assembly studies, more detailed descriptions of the early assemblies than had been available in the unclassified literature are provided. (U.S.)

Thermal neutron standard fields with the KUR heavy water facility

International Nuclear Information System (INIS)

Kanda, K.; Kobayashi, K.; Shibata, T.

1978-01-01

A heavy water facility attached to the KUR (Kyoto University Reactor, swimming pool type, 5 MW) yields pure thermal neutrons in the Maxwellian distribution. The facility is faced to the core of KUR and it contains about 2 tons of heavy water. The thickness of the layer is about 140 cm. The neutron spectrum was measured with the time of flight technique using a fast chopper. The measured spectrum was in good agreement with the Maxwellian distribution in all energy region for thermal neutrons. The neutron temperature was slightly higher than the heavy water temperature. The contamination of epithermal and fast neutrons caused by photo-neutrons of the γ-n reaction of heavy water was very small. The maximum intensity of thermal neutrons is 3x10 11 n/cm 2 sec. When the bismuth scatterer is attached, the gamma rays contamination is eliminated by the ratio of 0.05 of gamma rays to neutrons in rem. This standard neutron field has been used for such experiments as thermal neutron cross section measurement, detector calibration, activation analysis, biomedical purposes etc. (author)

1000 tones of heavy water produced at ROMAG PROD, Drobeta-Turnu Severin

International Nuclear Information System (INIS)

2001-01-01

On May 25, 2001 the heavy water plant ROMAG PROD at Drobeta-Turnu Severin recorded the production of the 1000-th tone of nuclear purity heavy water. The heavy water plant ROMAG PROD makes use of a technology based on the results of isotopic deuterium separation research carried out at the Research and Design Institutes of Cluj, Craiova, Pitesti and Ploiesti during 1957-1970 and the separation technology tested at Ramnicu-Valcea pilot plant (at present the Cryogenics and Isotope Separation Institute). The first investments at ROMAG PROD were made in 1979 and on July 17, 1988 was produced the first amount of heavy water at the required parameters for CANDU type nuclear reactors. The period between 1990-1992 was dedicated to the project completion, upgrading the technological facilities and retrofitting the environmental protection and monitoring systems. Production was resumed in 1992. The first 500 t of heavy water required for the Cernavoda NPP first reactor operation were produced by summer 1997. The additional amount of 500 t of heavy water was produced between 1997-2001. ROMAG PROD obtained the ISO 9001/2001 certificate for the quality management system, the ISO 14001/1997 certificate for the environmental management system and the new environmental permit

Heat exchangers in heavy water reactor systems

International Nuclear Information System (INIS)

Mehta, S.K.

1988-01-01

Important features of some major heat exchange components of pressurized heavy water reactors and DHRUVA research reactor are presented. Design considerations and nuclear service classifications are discussed

Environmental assessment of ground water pollution by heavy ...

African Journals Online (AJOL)

The aim of this study was to investigate the relationship between the concentrations of heavy metals in well water and bioaccumulation of the most abundant metals in chicken tissues in some areas in the province of Mecca Almokaramah, Saudi Arabia. Among the heavy metals (Cd, Zn, Cr, Mn, Cu Hg, Pb and Ni) studied, ...

Reflector construction by sound path curves - A method of manual reflector evaluation in the field

International Nuclear Information System (INIS)

Siciliano, F.; Heumuller, R.

1985-01-01

In order to describe the time-of-flight behavior of various reflectors we have set up models and derived from them analytical and graphic approaches to reflector reconstruction. In the course of this work, maximum achievable accuracy and possible simplifications were investigated. The aim of the time-of-flight reconstruction method is to determine the points of a reflector on the basis of a sound path function (sound path as the function of the probe index position). This method can only be used on materials which are isotropic in terms of sound velocity since the method relies on time of flight being converted into sound path. This paper deals only with two-dimensional reconstruction, in other words all statements relate to the plane of incidence. The method is based on the fact that the geometrical location of the points equidistant from a certain probe index position is a circle. If circles with radiuses equal to the associated sound path are drawn for various search unit positions the points of intersection of the circles are the desired reflector points

Flexible-Robotic Reflector for Aerospace Applications

Directory of Open Access Journals (Sweden)

Nir Shvalb

2015-01-01

Full Text Available Existing dish based antennas tend to have geometric morphologic distortion in the surface due to drastic thermal changes common in the space environment. In this paper we present a new concept for a dynamic antenna specially designed for communication satellites. The suggested flexible-robotic antenna is based on a dual-reflector structure, where the subreflector has a complex surface shaping robotic mechanism allowing it to fix most of the morphologic errors in the main reflector. We have implemented a set of searching algorithms allowing the hyper redundant robotic subreflector to adapt its surface to the morphologic distortions in the main reflector. The suggested new antenna was constructed and tested in an RF room in which it was able to fix the loss caused by distortion in the main reflector to the original gain in less than an hour.

Research of flaw assessment methods for beryllium reflector elements

International Nuclear Information System (INIS)

Shibata, Akira; Ito, Masayasu; Takemoto, Noriyuki; Tanimoto, Masataka; Tsuchiya, Kunihiko; Nakatsuka, Masafumi; Ohara, Hiroshi; Kodama, Mitsuhiro

2012-02-01

Reflector elements made from metal beryllium is widely used as neutron reflectors to increase neutron flux in test reactors. When beryllium reflector elements are irradiated by neutron, bending of reflector elements caused by swelling occurs, and beryllium reflector elements must be replaced in several years. In this report, literature search and investigation for non-destructive inspection of Beryllium and experiments for Preliminary inspection to establish post irradiation examination method for research of characteristics of metal beryllium under neutron irradiation were reported. (author)

Operating experiences on ammonia water exchange system at Heavy Water Plant, Talcher (paper No. 6.12)

International Nuclear Information System (INIS)

Venkat Ram, D.; Sharma, A.K.

1992-01-01

The Heavy Water Plant at Talcher employs bithermal ammonia hydrogen exchange process for the production of heavy water. The paper describes about the existing ammonia water exchange column, its start-up, operating experience and the problems encountered in operation of the column. The operating experiences gained and the data collected over the last few years can be utilised for design and operation of new ammonia water exchange column. (V.R). 2 figs

Heavy metal partitioning of suspended particulate matter-water and sediment-water in the Yangtze Estuary.

Science.gov (United States)

Feng, Chenghong; Guo, Xiaoyu; Yin, Su; Tian, Chenhao; Li, Yangyang; Shen, Zhenyao

2017-10-01

The partitioning of ten heavy metals (As, Cd, Co, Cr, Cu, Hg, Ni, Pb, Sb, and Zn) between the water, suspended particulate matter (SPM), and sediments in seven channel sections during three hydrologic seasons in the Yangtze Estuary was comprehensively investigated. Special attention was paid to the role of tides, influential factors (concentrations of SPM and dissolved organic carbon, and particle size), and heavy metal speciation. The SPM-water and sediment-water partition coefficients (K p ) of the heavy metals exhibited similar changes along the channel sections, though the former were larger throughout the estuary. Because of the higher salinity, the K p values of most of the metals were higher in the north branch than in the south branch. The K p values of Cd, Co, and As generally decreased from the wet season to the dry season. Both the diagonal line method and paired samples t-test showed that no specific phase transfer of heavy metals existed during the flood and ebb tides, but the sediment-water K p was more concentrated for the diagonal line method, owing to the relatively smaller tidal influences on the sediment. The partition coefficients (especially the K p for SPM-water) had negative correlations with the dissolved organic carbon (DOC) but positive correlations were noted with the particle size for most of the heavy metals in sediment. Two types of significant correlations were observed between K p and metal speciation (i.e., exchangeable, carbonate, reducible, organic, and residual fractions), which can be used to identify the dominant phase-partition mechanisms (e.g., adsorption or desorption) of heavy metals. Copyright © 2017 Elsevier Ltd. All rights reserved.

Change of deuterium volume content in heavy water during carbon dioxide dissolution in it

International Nuclear Information System (INIS)

Efimova, T.I.; Kapitanov, V.F.; Levchenko, G.V.

1985-01-01

Carbon dioxide solution density in heavy water at increased temperature and pressure is measured and the influence of carbon dioxide solubility in heavy water on volumetric content of deuterium in it is determined. Investigations were conducted in the temperature range of 303-473 K and pressure range of 3-20 MPa by the autoclave method. Volumetric content of deuterium in heavy water decreases sufficiently with CO 2 dissolved in it in comparison with pure D 2 O under the similar conditions, and this decrease becomes more sufficient with the pressure increase. With the temperature increase the volumetric content of deuterium both for heavy water and for saturated carbon solution in heavy water decreases

The future 700 MWe pressurized heavy water reactor

International Nuclear Information System (INIS)

Bhardwaj, S.A.

2006-01-01

The design of a 700 MWe pressurized heavy water reactor has been developed. The design is based on the twin 540 MWe reactors at Tarapur of which the first unit has been made critical in less than 5 years from construction commencement. In the 700 MWe design boiling of the coolant, to a limited extent, has been allowed near the channel exit. While making the plant layout more compact, emphasis has been on constructability. Saving in capital cost of about 15%, over the present units, is expected. The paper describes salient design features of 700 MWe pressurized heavy water reactor

Optimized reflectors for non-tracking solar collectors with tubular absorbers

Energy Technology Data Exchange (ETDEWEB)

Muschaweck, Julius [Optics and Energy Consulting, Munich (Germany); Spirkl, Wolfgang [Ludwig-Maximilians Univ., Sektion Physik, Munich (Germany); Timinger, Andreas [Optics and Energy Consulting, Munich (Germany); ZAE Bayern, Solar Thermal and Biomass Dept., Munich (Germany); Benz, Nikolaus; Doerfler, Michael; Gut, Martin [ZAE Bayern, Solar Thermal and Biomass Dept., Munich (Germany); Kose, Erwin [microtherm Energietecjnik GmbH, Lods, 25 (France)

2000-07-01

We present an approach to find optimal reflector shapes for non-tracking solar collectors under practical constraints. We focus on cylindrical absorbers and reflectors with translational symmetry. Under idealised circumstances, edge ray reflectors are well known to be optimal. However, it is not clear how optimal reflectors should be shaped in order to obtain maximum utilisable energy for given operating temperatures under practical constraints like reflectivity less than unity, real radiation data, size limits, and gaps between the reflector and the absorber. For a prototype collector with a symmetric edge ray reflector and a tubular absorber, we derive from calorimetric measurements under outdoor conditions the optical efficiency as a function of the incidence angle. Using numerical optimisation and raytracing, we compare truncated symmetric edge ray reflectors, truncated asymmetric edge ray reflectors and free forms parametrized by Bezier splines. We find that asymmetric edge ray reflectors are optimal. For reasonable operating conditions, truncated asymmetric edge ray reflectors allow much better land use and easily adapt to a large range of roof tilt angles with marginal changes in collector construction. Except near the equator, they should increase the yearly utilisable energy per absorber tube by several percent as compared to the prototype collector with symmetric reflectors. (Author)

Removal of gadolinium nitrate from heavy water

Energy Technology Data Exchange (ETDEWEB)

Wilde, E.W.

2000-03-22

Work was conducted to develop a cost-effective process to purify 181 55-gallon drums containing spent heavy water moderator (D2O) contaminated with high concentrations of gadolinium nitrate, a chemical used as a neutron poison during former nuclear reactor operations at the Savannah River Site (SRS). These drums also contain low level radioactive contamination, including tritium, which complicates treatment options. Presently, the drums of degraded moderator are being stored on site. It was suggested that a process utilizing biological mechanisms could potentially lower the total cost of heavy water purification by allowing the use of smaller equipment with less product loss and a reduction in the quantity of secondary waste materials produced by the current baseline process (ion exchange).

Selected bibliography on deuterium isotope effects and heavy water

International Nuclear Information System (INIS)

Dave, S.M.; Donde, M.M.

1983-01-01

In recent years, there has been a great deal of interest in using deuterium and heavy water not only in nuclear industry but also in various fields of basic as well as applied research in physics, chemistry and biology. As a result, the literature is being enriched with a large number of research papers and technical reports published each year. Thus, to enable the scientists to have an easy reference to these works, an endeavour has been made in this selected bibliography, to enlist the publications related to these fields. Since the interest is concerned mainly with heavy water production processes, deuterium isotope effects etc., several aspects (e.g. nuclear) of deuterium have not been covered here. The material in this bibliography which cites 2388 references has been classified under six broad headings, viz. (1) Production of heavy water, (2) Study of deuterium isotope effects, (3) Analysis and Properties of heavy water, (4) Laser Separation of deuterium, (5) Isotopic exchange reactions, and (6) Miscellaneous. The sources of information used for this compilation are chemical abstracts, nuclear science abstracts, INIS Atomindex and also some scattered search through journals and reports available in the B.A.R.C. library. However, in spite of sincere attempts for a wide coverage, no claim is being made towards the exhaustiveness of this bibliography. (author)

Distribution of the thermal neutron field around the graphite reflector of the Dalat Nuclear Research Reactor

Energy Technology Data Exchange (ETDEWEB)

Huy, Ngo Quang [Centre for Nuclear Technique Application, Ho Chi Minh City (Viet Nam); Thong, Ha Van; Long, Vu Hai; Khang, Ngo Phu; Binh, Nguyen Duc; Tuan, Nguyen Minh; Vinh, Le Vinh [Nuclear Research Inst., Da Lat (Viet Nam)

1994-10-01

Thermal neutron flux distributions around the graphite reflector of the Dalat Nuclear Research Reactor are determined by the method for neutron activating Cu foils. The major results are as follows: a/The axial distributions at the inner and outer margins of the graphite reflector have unsymmetrical shapes, similar to axial distributions in the core. There is a dissimilarity between the distribution curves at the inner margin and those at the outer margin of the reflector. b/ The radial distribution on the upper surface of the graphite reflector is measured and is described by the two-group neutron diffusion theory. The maximal value of the curve lies at the position of R{sub m}ax = 22.5 cm. c/ The distribution in the twenty water irradiation holes around the rotary specimen rack is obtained. (author). 3 refs., 5 figs., 1 tab.

Development of Full-Scale Ultrathin Shell Reflector

Directory of Open Access Journals (Sweden)

Durmuş Türkmen

2012-01-01

Full Text Available It is aimed that a new ultrathin shell composite reflector is developed considering different design options to optimize the stiffness/mass ratio, cost, and manufacturing. The reflector is an offset parabolic reflector with a diameter of 6 m, a focal length of 4.8 m, and an offset of 0.3 m and has the ability of folding and self-deploying. For Ku-band missions a full-scale offset parabolic reflector antenna is designed by considering different concepts of stiffening: (i reflective surface and skirt, (ii reflective surface and radial ribs, and (iii reflective surface, skirt, and radial ribs. In a preliminary study, the options are modeled using ABAQUS finite element program and compared with respect to their mass, fundamental frequency, and thermal surface errors. It is found that the option of reflective surface and skirt is more advantageous. The option is further analyzed to optimize the stiffness/mass ratio considering the design parameters of material thickness, width of the skirt, and ply angles. Using the TOPSIS method is determined the best reflector concept among thirty different designs. Accordingly, new design can be said to have some advantages in terms of mass, natural frequency, number of parts, production, and assembly than both SSBR and AstroMesh reflectors.

Solar reflector

Energy Technology Data Exchange (ETDEWEB)

Dvorak, J

1983-01-15

The reflector in the form of part of a cylindrical surface delimited by two envelopes is installed on a platform which can move on an inclined curvilinear path. The angle of inclination of the path depends on the latitude of the locality. The reflected rays are focused on the tubular absorber. One of the axes of the platform is linked to a brake controlled by a sensor for intensity of solar radiation. The sensor is a pipe filled with liquid with high value of the temperature expansion coefficient, for example alcohol. The pipe is insulated from one side and is accessible to the solar rays from the opposite. One end of the pipe is equipped with a bending end or piston. In order to expand the fluid in the sensor, the pipe acts on the brake, and the reflector is installed in a position corresponding to the maximum radiation intensity.

Eliminating Heavy Metals from Water with NanoSheet Minerals as Adsorbents

Directory of Open Access Journals (Sweden)

Shaoxian Song

2017-12-01

Full Text Available Heavy metals usually referred to those with atomic weights ranging from 63.5 to 200.6. Because of natural-mineral dissolution and human activities such as mining, pesticides, fertilizer, metal planting and batteries manufacture, etc., these heavy metals, including zinc, copper, mercury, lead, cadmium and chromium have been excessively released into water courses, like underground water, lake and river, etc. The ingestion of the heavy metals-contaminated water would raise serious health problems to human beings even at a low concentration. For instance, lead can bring human beings about barrier to the normal function of kidney, liver and reproductive system, while zinc can cause stomach cramps, skin irritations, vomiting and anemia. Mercury is a horrible neurotoxin that may result in damages to the central nervous system, dysfunction of pulmonary and kidney, chest and dyspnea. Chromium (VI has been proved can cause many diseases ranging from general skin irritation to severe lung carcinoma. Accordingly, the World Health Organization announced the maximum contaminant levels (MCL for the heavy metals in drinking water. There are numerous processes for eliminating heavy metals from water in order to provide citizens safe drinking water, including precipitation, adsorption, ion exchange, membrane separation and biological treatment, etc. Adsorption is considered as a potential process for deeply removing heavy metals, in which the selection of adsorbents plays a predominant role. Nano-sheet minerals as the adsorbents are currently the hottest researches in the field. They are obtained from layered minerals, such as montmorillonite, graphite and molybdenite, through the processing of intercalation, electrochemical and mechanical exfoliation, etc. Nano-sheet minerals are featured by their large specific surface area, relatively low costs and active adsorbing sites, leading to be effective and potential adsorbents for heavy metals removal from water

Geological signatures of drillhole radar reflectors in ONKALO

International Nuclear Information System (INIS)

Doese, C.; Gustafsson, J.

2011-12-01

The geological signatures of radar reflectors in ONKALO have been evaluated as a subactivity within the Joint Work Programme 'Rock Suitability Criteria' strategies and methodology' between Svensk Kaernbraenslehantering AB and Posiva Oy. In addition to the geological signature, the usage of geophysical data to predict large fractures was evaluated. Pilot hole radar loggings were carried out using a RAMAC GPR-250 MHz dipole antenna. The radar data were evaluated and reflectors with known position and intersection angle to the pilot hole were correlated with fractures or foliation in the pilot hole and with Tunnel Crosscutting Fractures in the tunnel. This data served as in-data for the evaluation of the geological signatures of radar reflectors. The result of the evaluation is not univocal. Half of the reflectors could be explained by fractures in the pilot hole, but only about 10 % of the reflectors can be explained by Tunnel Crosscutting Fractures. Of these 10 %, 2/3 can also be explained by foliation, leaving only some 3 % of the total reflectors more unambiguously correlated with Tunnel Crosscutting Fractures. The fractures correlated with radar reflectors do not diverge much from other fractures. Fractures having intersection angles of 30 deg- 60 deg are more likely to be detected by radar relative to other. Other properties that seem to be overrepresented in fractures correlated with radar reflectors are quartz and/or graphite content, width ≥0.8 mm and higher alteration (J a ≥3), but the data is not unambiguous. (orig.)

Neutrinos: Heavy water detector

International Nuclear Information System (INIS)

Anon.

1990-01-01

The proponents of the Sudbury Neutrino Observatory (SNO) received a welcome Christmas present when William Winegard, Canadian Minister for Science and Technology announced the final details of the funding for this project, totalling 48 million Canadian dollars and including contributions from the US and the UK. The SNO experiment will extend significantly the study of solar neutrinos, using some 1,000 tonnes of heavy water to be installed more than two kilometres below ground in a nickel mine at Sudbury, Ontario

Square Van Atta reflector with conducting mounting flame

DEFF Research Database (Denmark)

Nielsen, Erik Dragø

1970-01-01

A theoretical and numerical analysis of square Van Atta reflectors has been carried out with or without a conducting plate, used for mounting of the antenna elements. The Van Atta reflector investigated has antenna elements which are parallel half-wave dipoles interconnected in pairs by transmiss......A theoretical and numerical analysis of square Van Atta reflectors has been carried out with or without a conducting plate, used for mounting of the antenna elements. The Van Atta reflector investigated has antenna elements which are parallel half-wave dipoles interconnected in pairs...

Ellisoidal reflector for measuring otoacoustic emissions

DEFF Research Database (Denmark)

Epp, Bastian; Heiskanen, Vesa; Pulkki, Ville Topias

2016-01-01

ear canal. This study presents the design and evaluation of a truncated prolate ellipsoidal reflector in combination with a large-diaphragm low-noise microphone to measure OAEs in the open ear canal of human listeners. The reflector was designed to gain information about BM processing at low...

Adaptive Nulling in Hybrid Reflector Antennas

Science.gov (United States)

1992-09-01

correction of reflector distortion and vernier beamsteering, MEEE Trans. Antennas Propagat, 36:1351-1358. 4 Cherrette , A.R., et al (1989) Compensation of...Propagat, 36:1351-1358. 4. Cherrette , A.R., et al (1989) Compensation of reflector antenna surface distortion using an array feed,IEEE Trans. Antennas

Optimization of reflector-boosters for solar flat-collectors

Energy Technology Data Exchange (ETDEWEB)

Profant, M; Weidner, P; Boettcher, A

1979-04-01

To increase the working temperature of solar energy systems two-sided collectors together with appropriate reflectors are used. Here, the efficiency of various reflector shapes was investigated and attempts made to optimize them under several criteria. The results indicate that with cheap and simple to manufacture reflectors good energy gains can be expected.

Precision segmented reflectors for space applications

Science.gov (United States)

Lehman, David H.; Pawlik, Eugene V.; Meinel, Aden B.; Fichter, W. B.

1990-08-01

A project to develop precision segmented reflectors (PSRs) which operate at submillimeter wavelengths is described. The development of a light efficient means for the construction of large-aperture segmented reflecting space-based telescopes is the primary aim of the project. The 20-m Large Deployable Reflector (LDR) telescope is being developed for a survey mission, and it will make use of the reflector panels and materials, structures, and figure control being elaborated for the PSR. The surface accuracy of a 0.9-m PSR panel is shown to be 1.74-micron RMS, the goal of 100-micron RMS positioning accuracy has been achieved for a 4-m erectable structure. A voice-coil actuator for the figure control system architecture demonstrated 1-micron panel control accuracy in a 3-axis evaluation. The PSR technology is demonstrated to be of value for several NASA projects involving optical communications and interferometers as well as missions which make use of large-diameter segmented reflectors.

Design of partially optically stable reflector systems and prisms

Science.gov (United States)

Tsai, Chuang-Yu

2010-09-01

The characteristics and design method of the total optically stable (TOS) reflector systems/prisms were introduced in an early paper (Tsai and Lin in Appl. Opt. 47:4158-4163, 2008), where only two types of TOS reflector system exist, namely preservation or retroreflection. In this paper, we introduce the partially optically stable (POS) reflector system, which is only optically stable about a specific directional vector; nevertheless, the exiting light ray is not restricted to preservation or retroreflection. The proposed paper also presents an analytic method for the design of POS reflector systems comprised of multiple reflectors. Furthermore, it is shown that a POS prism can be obtained by adding two refracting flat boundary surfaces with specific conditions at the entrance and exit positions of the light ray in an optical system with multiple reflectors.

[Effect of Recycled Water Irrieation on Heavy Metal Pollution in Irrigation Soil].

Science.gov (United States)

Zhou, Yi-qi; Liu, Yun-xia; Fu, Hui-min

2016-01-15

With acceleration of urbanization, water shortages will become a serious problem. Usage of reclaimed water for flushing and watering of the green areas will be common in the future. To study the heavy metal contamination of soils after green area irrigation using recycled wastewater from special industries, we selected sewage and laboratory wastewater as water source for integrated oxidation ditch treatment, and the effluent was used as irrigation water of the green area. The irrigation units included broad-leaved forest, bush and lawn. Six samples sites were selected, and 0-20 cm soil of them were collected. Analysis of the heavy metals including Cr, Mn, Ni, Cu, Zn, As, Cd and Pb in the soil showed no significant differences with heavy metals concentration in soil irrigated with tap water. The heavy metals in the soil irrigated with recycled water were mainly enriched in the surface layer, among which the contents of Cr, Ni, Cu, Zn and Pb were below the soil background values of Beijing. A slight pollution of As and Cd was found in the soil irrigated by recycled water, which needs to be noticed.

Investigation of the heavy water distillation system at the RA reactor

International Nuclear Information System (INIS)

Zecevic, V.; Badrljica, R.

1963-01-01

The heavy water distillation system was tested because this was not done before the reactor start-up. Detailed inspection of the system components showed satisfactory results. Leak testing was done as well as the testing of the instrumentation which enables reliable performance of the system. Performance testing was done with ordinary water and later 2700 l of heavy water from the reactor was purified, decreasing the activity by 45%

Heavy metal contamination of soil and water in the vicinity of an abandoned e-waste recycling site: implications for dissemination of heavy metals.

Science.gov (United States)

Wu, Qihang; Leung, Jonathan Y S; Geng, Xinhua; Chen, Shejun; Huang, Xuexia; Li, Haiyan; Huang, Zhuying; Zhu, Libin; Chen, Jiahao; Lu, Yayin

2015-02-15

Illegal e-waste recycling activity has caused heavy metal pollution in many developing countries, including China. In recent years, the Chinese government has strengthened enforcement to impede such activity; however, the heavy metals remaining in the abandoned e-waste recycling site can still pose ecological risk. The present study aimed to investigate the concentrations of heavy metals in soil and water in the vicinity of an abandoned e-waste recycling site in Longtang, South China. Results showed that the surface soil of the former burning and acid-leaching sites was still heavily contaminated with Cd (>0.39 mg kg(-1)) and Cu (>1981 mg kg(-1)), which exceeded their respective guideline levels. The concentration of heavy metals generally decreased with depth in both burning site and paddy field, which is related to the elevated pH and reduced TOM along the depth gradient. The pond water was seriously acidified and contaminated with heavy metals, while the well water was slightly contaminated since heavy metals were mostly retained in the surface soil. The use of pond water for irrigation resulted in considerable heavy metal contamination in the paddy soil. Compared with previous studies, the reduced heavy metal concentrations in the surface soil imply that heavy metals were transported to the other areas, such as pond. Therefore, immediate remediation of the contaminated soil and water is necessary to prevent dissemination of heavy metals and potential ecological disaster. Copyright © 2014 Elsevier B.V. All rights reserved.

Experimental Study on Behavior of Bow-tie Tree Generation by Using Heavy Water

Science.gov (United States)

Kumazawa, Takao; Nakagawa, Wataru; Tsurumaru, Hidekazu

Bow-tie tree (BTT) generated from contaminant, e.g., metal, carbon, amber(over cured resin) or void in insulator is a significant deterioration factor of XLPE power cable. However, essential role of water in generation and progress of BTT is not yet sufficiently cleared. In order to investigate the role of water we paid attention to difference in chemical properties of light water (H2O) and heavy water (D2O), moreover we evaluated influence of isotopic effect due to hydrogen and deuterium on behavior of BTT generation. In accelerated aging test the number of BTT in XLPE sample, in which copper powder of 500ppm was contaminated as BTT cores, dipped in heavy water (D2O:100wt%) decreased to one third compared with light water(D2O:0wt%). Furthermore, the maximum length of BTT decreased with increase in concentration of heavy water. The experimental results show that heavy water exerted a depression effect on generation and progress of BTT. We considered that the depression effect due to hydrogen isotope appeared by inhibiting ionization and elution of BTT cores, because salt-solubility and ionic mobility of heavy water are about 15 to 20% smaller than those of light water. Therefore, the essential role of water seemed to be production and transport of ions in XLPE.

Operating performance of the prototype heavy water reactor Fugen

International Nuclear Information System (INIS)

1984-01-01

Since the full scale operation was started in March, 1979, the ATR Fugen power station has been verifying the performance and reliability of the machinery and equipment, uranium-plutonium mixed oxide fuel and so on, and obtaining the technical prospect for putting ATRs in practical use by accumulating operation and maintenance techniques, through about five years of operation. In this report, the operational results of the Fugen power station are described. Fugen is a heavy water-moderated, boiling light water-cooled, pressure tube type reactor with 165 MWe output. As of the end of March, 1984, the total generated electric power was about 4.3 billion kWh, and the operation time was about 27,000 hours. The mean capacity ratio reached 58.8%. During the operation period, troubles including plant shutdown occurred eight times, but generally the performance and reliability of the machinery and equipment have been good. 580 fuels including 284 MOX fuels have been charged, but fuel breaking did not occur at all. The consumption of heavy water and the leak of tritium did not cause problem. The management of the core and fuel, the management of maintenance, the quality control of cooling water and heavy water, radiation control and the management of wastes are reported. (Kako, I.)

Light and heavy water replacing system in reactor container

International Nuclear Information System (INIS)

Miyamoto, Keiji.

1979-01-01

Purpose: To enable to determine the strength of a reactor container while neglecting the outer atmospheric pressure upon evacuation, by evacuating the gap between the reactor container and a biological thermal shield, as well as the container simultaneously upon light water - heavy water replacement. Method: Upon replacing light water with heavy water by vacuum evaporation system in a nuclear reactor having a biological thermal shield surrounding the reactor container incorporating therein a reactor core by way of a heat expansion absorbing gap, the reactor container and the havy water recycling system, as well as the inside of heat expansion absorbing gap are evacuated simultaneously. This enables to neglect the outer atmospheric outer pressure upon evacuation in the determination of the container strength, and the thickness of the container can be decreased by so much as the external pressure neglected. (Moriyama, K.)

Design of node record for fast active reflector

International Nuclear Information System (INIS)

Wu Wenqing; Luo Mingcheng; Tang Pengyi; Liu Jiajing; Wang Jian

2014-01-01

Active Reflector is the one of the innovations of Five hundred meter Aperture Spherical Telescope (FAST) whose performance touches on that of the overall telescope. Therefore a real time control system is needed by the Active Reflector System. In this paper, a new record type-node record is designed for EPICS-based active reflector control system of FAST, according to more than 2000 controlled node, which will be convenient for node management of IOC and prove the reusage of IOC codes. The record type is used in design of active reflector control system of FAST Miyun model. (authors)

Reflector Performance Study in Ultra-long Cycle Fast Reactor

International Nuclear Information System (INIS)

Tak, Taewoo; Kong, Chidong; Choe, Jiwon; Lee, Deokjung

2013-01-01

There are reflector assemblies outside the fuel region, surrounding the fuel assemblies and axial reflector is located at the bottom of the core to control the neutron leakage fraction which is an important factor in fast reactor system. HT-9 was used as a reflector material as well as a structure material. In this study, alternative reflector materials were proposed and their reflection performance was tested and studied focused on its physics. ODS-MA957 and SiC were chosen from iron based alloy and ceramic respectively. The two materials were tested and compared with HT-9 in UCFR-1000 as a radial and an axial reflector and it was evaluated from the neutronics point of view with comparing the core life and the coolant void reactivity. The calculation and evaluation were performed by McCARD Monte Carlo code. The reflector materials for UCFR-1000 have been investigated in the aspect of neutronics. The reflection effect shows different performance corresponding to reflector material used. Also, the neutron energy spectrum is affected by changing materials which causes spectrum softening but it is not enough to influence the core life. With more reflector material candidates such as lead-based liquid metal, reflection performance and core parameter study will be investigated for next step

Approaching conversion limit with all-dielectric solar cell reflectors.

Science.gov (United States)

Fu, Sze Ming; Lai, Yi-Chun; Tseng, Chi Wei; Yan, Sheng Lun; Zhong, Yan Kai; Shen, Chang-Hong; Shieh, Jia-Min; Li, Yu-Ren; Cheng, Huang-Chung; Chi, Gou-chung; Yu, Peichen; Lin, Albert

2015-02-09

Metallic back reflectors has been used for thin-film and wafer-based solar cells for very long time. Nonetheless, the metallic mirrors might not be the best choices for photovoltaics. In this work, we show that solar cells with all-dielectric reflectors can surpass the best-configured metal-backed devices. Theoretical and experimental results all show that superior large-angle light scattering capability can be achieved by the diffuse medium reflectors, and the solar cell J-V enhancement is higher for solar cells using all-dielectric reflectors. Specifically, the measured diffused scattering efficiency (D.S.E.) of a diffuse medium reflector is >0.8 for the light trapping spectral range (600nm-1000nm), and the measured reflectance of a diffuse medium can be as high as silver if the geometry of embedded titanium oxide(TiO(2)) nanoparticles is optimized. Moreover, the diffuse medium reflectors have the additional advantage of room-temperature processing, low cost, and very high throughput. We believe that using all-dielectric solar cell reflectors is a way to approach the thermodynamic conversion limit by completely excluding metallic dissipation.

Efficient Wave Energy Amplification with Wave Reflectors

DEFF Research Database (Denmark)

Kramer, Morten Mejlhede; Frigaard, Peter Bak

2002-01-01

Wave Energy Converters (WEC's) extract wave energy from a limited area, often a single point or line even though the wave energy is generally spread out along the wave crest. By the use of wave reflectors (reflecting walls) the wave energy is effectively focused and increased to approximately 130......-140%. In the paper a procedure for calculating the efficiency and optimizing the geometry of wave reflectors are described, this by use of a 3D boundary element method. The calculations are verified by laboratory experiments and a very good agreement is found. The paper gives estimates of possible power benifit...... for different geometries of the wave reflectors and optimal geometrical design parameters are specified. On this basis inventors of WEC's can evaluate whether a specific WEC possible could benefit from wave reflectors....

The Bare Critical Assembly of Natural Uranium and Heavy Water

Energy Technology Data Exchange (ETDEWEB)

Popovic, D [Boris Kidric Institute of Nuclear Sciences, Vinca, Belgrade (Yugoslavia)

1958-07-01

The first reactor built in Yugoslavia was the bare zero energy heavy water and natural uranium assembly at the Boris Kidric Institute of Nuclear Sciences, Belgrade. The reactor went critical on April 29, 1958. The possession of four tons of natural uranium metal and the temporary availability of seven tons of heavy water encouraged the staff of the Institute to build a critical assembly. A critical assembly was chosen, rather than high flux reactor, because the heavy water was available only temporarily. Besides, a 10 MW, enriched uranium, research reactor is being built at the same Institute and should be ready for operation late this year. It was supposed that the zero energy reactor would provide experience in carrying out critical experiments, operational experience with nuclear reactors, and the possibility for an extensive program in reactor physics. (author)

Effect of graphite reflector on activation of fusion breeding blanket

International Nuclear Information System (INIS)

Lee, Cheol Woo; Lee, Young-Ouk; Lee, Dong Won; Cho, Seungyon; Ahn, Mu-Young

2016-01-01

Highlights: • The graphite reflector concept has been applied in the design of the Korea HCCR TBM for ITER and this concept is also a candidate design option for Korea Demo. • In the graphite reflector, C-14, B-11 and Be-10 are produced after an irradiation. Impurities in both case of beryllium and graphite is dominant in the shutdown dose after an irradiation. • Based on the evaluation, the graphite reflector is a good alternative of the beryllium multiplier in the view of induced activity and shutdown dose. But C-14 produced in the graphite reflector should be considered carefully in the view of radwaste management. - Abstract: Korea has proposed a Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept relevant to fusion power plants. Here, graphite is used as a reflector material by reducing the amount of beryllium multiplier. In this paper, activity analysis was performed and the effect of graphite reflector in the view of activation was compared to the beryllium multiplier. As a result, it is expected that using the graphite reflector instead of the beryllium multiplier decreases total activity very effectively. But the graphite reflector produces C-14 about 17.2 times than the beryllium multiplier. Therefore, C-14 produced in the graphite reflector is expected as a significant nuclide in the view of radwaste management.

Neutron disadvantage factors in heavy water and light water reactors

International Nuclear Information System (INIS)

Pop-Jordanov, J.

1966-01-01

A number od heavy water and light water reactor cells are analyzed in this paper by applying analytical methods of neutron thermalization. Calculations done according to the one-group Amouyal-Benoist method are included in addition. Computer codes for ZUSE Z-23 computer were written by applying both methods. The obtained results of disadvantage factors are then compared to results obtained by one-group P 3 approximation and by multigroup K7-THERMOS code [sr

Cost effective water treatment program in Heavy Water Plant (Manuguru)

International Nuclear Information System (INIS)

Mohapatra, C.; Prasada Rao, G.

2002-01-01

Water treatment technology is in a state of continuous evolution. The increasing urgency to conserve water and reduce pollution has in recent years produced an enormous demand for new chemical treatment programs and technologies. Heavy water plant (Manuguru) uses water as raw material (about 3000 m 3 /hr) and its treatment and management has benefited the plant in a significant way. It is a fact that if the water treatment is not proper, it can result in deposit formation and corrosion of metals, which can finally leads to production losses. Therefore, before selecting treatment program, complying w.r.t. quality requirements, safety and pollution aspects cost effectiveness shall be examined. The areas where significant benefits are derived, are raw water treatment using polyelectrolyte instead of inorganic coagulant (alum), change over of regenerant of cation exchangers from hydrochloric acid to sulfuric acid and in-house development of cooling water treatment formulation. The advantages and cost effectiveness of these treatments are discussed in detail. Further these treatments has helped the plant in achieving zero discharge and indirectly increased cost reduction of final product (heavy water); the dosage of 3 ppm of polyelectrolyte can replace 90 ppm alum at turbidity level of 300 NTU of raw water which has resulted in cost saving of Rs. 15-20 lakhs in a year beside other advantages; the change over of regenerant from HCl to H 2 SO 4 will result in cost saving of at least Rs.1.4 crore a year besides other advantages; the change over to proprietary formulation to in-house formulation in cooling water treatment has resulted in a saving about Rs.11 lakhs a year. To achieve the above objectives in a sustainable way the performance results are being monitored. (author)

Heavy metals concentrations in water bodies around aquamarine ...

African Journals Online (AJOL)

Water samples from three streams in the mining area of Eggon Hill were analysed. The Physicochemical values obtained were compared with WHO permissible standards in drinking water. Except for Cu and Zn with levels within permissible limits, other heavy metals determined were found to have levels above the WHO ...

Optimal design of orientation of PV/T collector with reflectors

International Nuclear Information System (INIS)

Kostic, Lj.T.; Pavlovic, T.M.; Pavlovic, Z.T.

2010-01-01

Hybrid conversion of solar radiation implies simultaneous solar radiation conversion into thermal and electrical energy in the PV/Thermal collector. In order to get more thermal and electrical energy, flat solar radiation reflectors have been mounted on PV/T collector. To obtain higher solar radiation intensity on PV/T collector, position of reflectors has been changed and optimal position of reflectors has been determined by both experimental measurements and numerical calculation so as to obtain maximal concentration of solar radiation intensity. The calculated values have been found to be in good agreement with the measured ones, both yielding the optimal position of the flat reflector to be the lowest (5 o ) in December and the highest (38 o ) in June. In this paper, the thermal and electrical efficiency of PV/T collector without reflectors and with reflectors in optimal position have been calculated. Using these results, the total efficiency and energy-saving efficiency of PV/T collector have been determined. Energy-saving efficiency for PV/T collector without reflectors is 60.1%, which is above the conventional solar thermal collector, whereas the energy-saving efficiency for PV/T collector with reflectors in optimal position is 46.7%, which is almost equal to the values for conventional solar thermal collector. Though the energy-saving efficiency of PV/T collector decreases slightly with the solar radiation intensity concentration factor, i.e. the thermal and electrical efficiency of PV/T collector with reflectors are lower than those of PV/T collector without reflectors, the total thermal and electrical energy generated by PV/T collector with reflectors in optimal position are significantly higher than total thermal and electrical energy generated by PV/T collector without reflectors.

Method for separation of water from bituminous shales, etc. [water-free heavy product and water-containing light product

Energy Technology Data Exchange (ETDEWEB)

Hellsing, G H

1908-10-13

The method is characterized by conducting all the products of distillation, coming from the retorts, into a controllable system of condensation. This system of condensation is so constructed that the products of distillation are cooled to such a temperature that only the water-free heavy distillates are being condensed, and is furthermore so constructed that the other products of distillation, not yet condensed, are being condensed in an ordinary system of coolers. The purpose is to separate the distillates into a water-free heavy product and a water-containing lighter product. The patent includes an additional claim.

Assessment of heavy metals in loose deposits in drinking water distribution system.

Science.gov (United States)

Liu, Quanli; Han, Weiqiang; Han, Bingjun; Shu, Min; Shi, Baoyou

2018-06-09

Heavy metal accumulation and potential releases from loose deposits in drinking water distribution system (DWDS) can have critical impacts on drinking water safety, but the associated risks have not been sufficiently evaluated. In this work, the potential biological toxicity of heavy metals in loose deposits was calculated based on consensus-based sediment quality guidelines, and the effects of some of the main water quality parameters, such as the pH and bicarbonate and phosphate content, on the release behaviors of pre-accumulated heavy metals were investigated. The results showed that heavy metals (Cu, As, Cr, Pb, and Cd) significantly accumulated in all the samples, but the contents of the heavy metals were multiple magnitudes lower than the Fe and Mn contents. The potential biotoxicity of As and Cu was relatively high, but the biotoxicity of Cd was negligible. The water quality can significantly influence the release of heavy metals from loose deposits. As the pH increased from 7.0 to 9.0, the release of As and Cr obviously increased. The release of As, Cu, Pb, and Cr also accelerated with the addition of phosphate (from 1 to 5 mg/L). In contrast to the trends for the pH and phosphate, variations in the bicarbonate content did not have a significant influence on the release of As and Cr. The release ratios of heavy metals in the samples were very low, and there was not a correlation between the release rate of the heavy metals in the loose deposits and their potential biotoxicity.

Nonimaging reflectors as functionals of the desired irradiance

International Nuclear Information System (INIS)

Winston, R.; Ries, H.

1993-01-01

For many tasks in illumination and collection the acceptance angle is required to vary along the reflector. If the acceptance angle function is known, then the reflector profile can be calculated as a functional of it. The total flux seen by an observer from a source of uniform brightness (radiance) is proportional to the sum of the view factor of the source and its reflection. This allows one to calculate the acceptance angle function necessary to produce a certain flux distribution and thereby construct the reflector profile. The authors demonstrate the method for several examples, including finite size sources with reflectors directly joining the source

Development of a portable heavy-water leak sensor based on laser absorption spectroscopy

International Nuclear Information System (INIS)

Lee, Lim; Park, Hyunmin; Kim, Taek-Soo; Kim, Minho; Jeong, Do-Young

2016-01-01

Highlights: • We developed a compact and portable laser sensor for a detection of heavy water leakage. • The sensor is wearable and also easy to use to search for the leak point. • It is sensitive enough to find invisible very tiny leaks. - Abstract: A compact and portable leak sensor based on cavity enhanced absorption spectroscopy has been newly developed for a detection of heavy water leakage which may happen in the facilities using heavy water such as pressurized heavy water reactor (PHWR). The developed portable sensor is suitable as an individual instrument for the measuring leak rate and finding the leak location because it is sufficiently compact in size and weight and operated by using an internal battery. In the performance test, the minimum detectable leak rate was estimated as 0.05 g/day from the calibration curve. This new sensor is expected to be a reliable and promising device for the detection of heavy water leakage since it has advantages on real-time monitoring and early detection for nuclear safety.

Sediment, water pollution indicators for heavy metals

International Nuclear Information System (INIS)

Cabaleiro, S.; Horn, A.

2010-01-01

The complexity of an aquatic system requires consideration of its dynamics: spatial and temporal variations of physical, chemical and biological. Heavy metals have peculiar behavior in the aquatic system and may not be available in the waters, but on sediments.The sub-basin of the Sarandi stream is responsible for the contamination of Pampulha Lake. The Instituto Mineiro das Águas – IGAM - uses tool for monitoring the quality of surface water for developing strategies for conservation, restoration and rational use of water resources. So through the indices: IQA ( Indice de qualidade de águas) Index of water quality, and TC- toxic contamination, reduces conflicts, implements the disciplining of the environmental economy.This study determined the monitoring of sediment and water of Sarandi Stream, so in the samples collected during dry and rainy seasons (2007- 2008) were analyzed heavy metals (Cu, Cd, Cr, Co, Ni, Zn, Pb) and physical-chemical factors (conductivity, solids dissolved, temperature, turbidity). This allowed the determination of Hackanson factors of contamination and Muller Index geoaccumulation, indicating very high contamination in sediments regarding the elements Cr, Cu, and Cd, and high contamination for Pb, Zn, and Mn. The comparison with the indices of water quality- IQA (IGAM - 2006, 2007 and 2008), combined with exploratory data analysis and graphs of correlation between the variables indicated favorable conditions for metals contamination on water and sediment for these metals, besides allowing the identification of its source

Critical evaluation of heavy water project at Thal (Preprint No. PM-5)

International Nuclear Information System (INIS)

Jayakumar, N.S.

1989-04-01

The project known as Thal Ammonia Extension was a heavy water project successfully completed by Rashtriya Chemicals and Fertilizers (RCF) Ltd. The project consisted of erecting a heavy water plant of 110 tons/year capacity at Thal. The process Know-how and engineering of the plant was supplied by the Heavy Water Projects Division of the Department of Atomic Energy. Salient features of the project, management features which resulted in fast completion of erection, bottlenecks faced and engineering innovations adopted for efficient operation of the plant are described. Some modifications which can lead to smoother operation are listed. (M.G.B.)

Phytoremediation of heavy metal-contaminated water and sediment by eleocharis acicularis

Energy Technology Data Exchange (ETDEWEB)

Sakakibara, Masayuki; Ha, Nguyen Thi Hoang [Graduate School of Science and Engineering, Ehime University, Matsuyama (Japan); Ohmori, Yuko [Graduate School of Science and Engineering, Ehime University, Matsuyama (Japan); Taisei Kiso Sekkei Co., Ltd., Tokyo (Japan); Sano, Sakae [Faculty of Education, Ehime University, Matsuyama (Japan); Sera, Koichiro [Cyclotron Center, Iwate Medical University, Takizawa-mura (Japan)

2011-08-15

Phytoremediation is an environmental remediation technique that takes advantage of plant physiology and metabolism. The unique property of heavy metal hyperaccumulation by the macrophyte Eleocharis acicularis is of great significance in the phytoremediation of water and sediments contaminated by heavy metals at mine sites. In this study, a field cultivation experiment was performed to examine the applicability of E. acicularis to the remediation of water contaminated by heavy metals. The highest concentrations of heavy metals in the shoots of E. acicularis were 20 200 mg Cu/kg, 14 200 mg Zn/kg, 1740 mg As/kg, 894 mg Pb/kg, and 239 mg Cd/kg. The concentrations of Cu, Zn, As, Cd, and Pb in the shoots correlate with their concentrations in the soil in a log-linear fashion. The bioconcentration factor for these elements decreases log-linearly with increasing concentration in the soil. The results indicate the ability of E. acicularis to hyperaccumulate Cu, Zn, As, and Cd under natural conditions, making it a good candidate species for the phytoremediation of water contaminated by heavy metals. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Assessment of heavy metals concentration in drinking water ...

African Journals Online (AJOL)

The concentration of all the metals were considerably found to be below the limit permitted by WHO's drinking water guidelines (WHO 2005). Findings suggest that continues water quality monitoring should be carried out to check the concentration levels of heavy metals in that area, to prevent them from been above the limit ...

Analysis of hydrogen sulfide releases in heavy water production facilities

International Nuclear Information System (INIS)

Croitoru, Cornelia; Dumitrescu, Maria; Preda, Irina; Lazar, Roxana

1996-01-01

Safety analyses conducted at ICIS concern primarily the heavy water production installations. The quantitative risk assessment needs the frequency calculation of accident sequences and consequences. In heavy water plants which obtain primary isotopic concentration of water by H 2 O - H 2 S exchange, large amounts of hydrogen sulfide which is a toxic, inflammable and explosive gas, are circulated. The first stage in calculating the consequences consists in potential analysis of H 2 S release. This work presents a study of this types of releases for pilot installations of the heavy water production at ICIS (Plant 'G' at Rm. Valcea). The installations which contain and maneuver large quantities of H 2 S and the mathematical models for different types of releases are presented. The accidents analyzed are: catastrophic column, container, spy-hole failures or gas-duct rupture and wall cracks in the installation. The main results are given as tables while the time variations of the flow rate and quantities of H 2 O released by stack disposal are plotted

Winter Maintenance Wash-Water Heavy Metal Removal Pilot Scale Evaluation

Directory of Open Access Journals (Sweden)

Christopher M. Miller

2016-01-01

Full Text Available To encourage sustainable engineering practices, departments of transportation are interested in reusing winter maintenance truck wash water as part of their brine production and future road application. Traffic-related metals in the wash water, however, could limit this option. The objective of this work was to conduct a pilot scale evaluation of heavy metal (copper, zinc, iron, and lead removal in a filtration unit (maximum flow rate of 45 L/minute containing proprietary (MAR Systems Sorbster® media. Three different trials were conducted and approximately 10,000 L of wash water collected from a winter maintenance facility in Ohio was treated with the pilot unit. Lab studies were also performed on six wash-water samples from multiple facilities to assess particle size removal and estimate settling time as a potential removal mechanism during wash-water storage. Pilot unit total metal removal efficiencies were 79%, 77%, 63%, and 94% for copper, zinc, iron, and lead, respectively. Particle settling calculation estimates for copper and zinc show that 10 hours in storage can also effectively reduce heavy metal concentrations in winter maintenance wash water in excess of 70%. These pilot scale results show promise for reducing heavy metal concentrations to an acceptable level for reuse.

Optical properties of nonimaging concentrators with corrugated reflectors

Science.gov (United States)

Roennelid, Mats; Perers, Bengt; Karlsson, Bjorn

1994-09-01

A ray tracing study has been performed on the optical properties of cylindrical nonimaging concentrators with linear corrugated reflectors. The corrugations are assumed to be V-formed and to have an extension parallel to the meridian plane of the concentrators. It is shown that the acceptance angle for radiation incident in the meridian plane can be increased for moderate corrugations. This increased acceptance is balanced by a decreased acceptance of radiation from other directions. Calculations of angular acceptance for a 2X compound parabolic concentrator is presented. It is shown that the annual irradiation on a solar collector with booster reflector can be increased if corrugated reflectors are used instead of smooth reflectors.

Thorium utilization in heavy water moderated Accelerator Driven Systems

International Nuclear Information System (INIS)

Bajpai, Anil; Degweker, S.B.; Ghosh, Biplab

2011-01-01

Research on Accelerator Driven Systems (ADSs) is being carried out around the world primarily with the objective of waste transmutation. Presently, the volume of waste in India is small and therefore there is little incentive to develop ADS based waste transmutation technology immediately. With limited indigenous U availability and the presence of large Th deposits in the country, there is a clear incentive to develop Th related technologies. India also has vast experience in design, construction and operation of heavy water moderated reactors. Heavy water moderated reactors employing solid Th fuels can be self sustaining, but the discharge burnups are too low to be economical. A possible way to improve the performance such reactors is to use an external neutron source as is done in ADS. This paper discusses our studies on Th utilization in heavy water moderated ADSs. The study is carried out at the lattice level. The time averaged k-infinity of the Th bundle from zero burnup up to the discharge burnup is taken to be the same as the core (ensemble) averaged k-infinity. For the purpose of the analysis we have chosen standard PHWR and AHWR assemblies. Variation of the pitch and coolant (H 2 O/D 2 O) are studied. Both, the once through cycle and the recycling option are studied. In the latter case the study is carried out for various enrichments (% 233 U in Th) of the recycled Th fuel bundles. The code DTF as modified for lattice and burnup calculations (BURNTRAN) was used for carrying out the study. The once through cycle represents the most attractive ADS concept (Th burner ADS) possible for Th utilization. It avoids reprocessing of Th spent fuel and in the ideal situation the use of any fissile material either initially or for sustaining itself. The gain in this system is however rather low requiring a high power accelerator and a substantial fraction of the power generated to be fed back to the accelerator. The self sustaining Th-U cycle in a heavy moderated ADS

Feasibility study and economic analysis on thorium utilization in heavy water reactors

International Nuclear Information System (INIS)

1978-07-01

Even though natural uranium is a more easily usable fuel in heavy water reactors, thorium fuel cycles have also been considered owing to certain attractive features of the thorium fuel cycle in heavy water reactors. The relatively higher fission neutron yield per thermal neutron absorption in 233 U combined with the very low neutron absorption cross section of heavy water make it possible to achieve breeding in a heavy water reactor operating on Th- 233 U fuel cycle. Even if the breeding ratio is very low, once a self-sustaining cycle is achieved, thereafter dependence on uranium can be completely eliminated. Thus, with a self-sustaining Th- 233 U fuel cycle in heavy water reactors, a given quantity of natural uranium will be capable of supporting a much larger installed generating capacity to significantly longer period of time. However, since thorium does not contain any fissile isotope, fissile material has to be added at the beginning. Concentrated fissile material is considerably more expensive than the 235 U contained in natural uranium. This makes the fuel cycle cost higher with thorium fuel cycle, at least during the initial stages. The situation is made worse by the fact that, because of its higher thermal neutron absorption cross section, thorium requires a higher concentration of fissile material than 238 U. Nevertheless, because of the superior nuclear characteristics of 233 U, once uranium becomes more expensive, thorium fuel cycle in heavy water reactors may become economically acceptable. Furthermore, the energy that can be made available from a given quantity of uranium is considerably increased with a self-sustaining thorium fuel cycle

Acoustic levitation with self-adaptive flexible reflectors.

Science.gov (United States)

Hong, Z Y; Xie, W J; Wei, B

2011-07-01

Two kinds of flexible reflectors are proposed and examined in this paper to improve the stability of single-axis acoustic levitator, especially in the case of levitating high-density and high-temperature samples. One kind is those with a deformable reflecting surface, and the other kind is those with an elastic support, both of which are self-adaptive to the change of acoustic radiation pressure. High-density materials such as iridium (density 22.6 gcm(-3)) are stably levitated at room temperature with a soft reflector made of colloid as well as a rigid reflector supported by a spring. In addition, the containerless melting and solidification of binary In-Bi eutectic alloy (melting point 345.8 K) and ternary Ag-Cu-Ge eutectic alloy (melting point 812 K) are successfully achieved by applying the elastically supported reflector with the assistance of a laser beam.

Wideband QAMC reflector's antenna for low profile applications

Science.gov (United States)

Grelier, M.; Jousset, M.; Mallégol, S.; Lepage, A. C.; Begaud, X.; LeMener, J. M.

2011-06-01

A wideband reflector's antenna based on quasi-artificial magnetic conductor is proposed. To validate the design, an Archimedean spiral has been backed to this new reflector. In comparison to classical solution using absorbent material, the prototype presents a very low thickness of λ/15 at the lowest operating frequency and an improved gain over a 2.4:1 bandwidth. The whole methodology to design this reflector can be applied to other wideband antennas.

Method of extracting tritium from heavy water

International Nuclear Information System (INIS)

Tsuchiya, Hiroyuki; Kikuchi, Makoto; Asakura, Yamato; Yusa, Hideo.

1979-01-01

Purpose: To extract tritium in heavy water by combining isotope exchange reaction with liquefaction distillation to increase the concentration of recovered tritium, thereby reducing the quantity of radioactive wastes recovered. Constitution: Heavy water containing tritium from a reactor is introduced into a tritium separator through a conduit pipe. On the other hand, a D 2 gas is introduced through the conduit pipe in the lower part of a tritium separator to transfer tritium into D 2 gas by isotope exchange. The D 2 gas containing DT is introduced into a liquefaction distillation tower together with an outlet gas of a converter supplied through a pipeline. The converter is filled with net-like metals of platinum group such as Pt, Ni, Pd and the like, and the D 2 gas affluent in DT, extracted from the distillation tower is converted into D 2 and T 2 . The gas which has been introduced into the liquefaction distillation tower is liquefied. The D 2 gas of low boiling point components reaches the tower top, and the T 2 gas of high boiling point components is concentrated at the tower bottom, and is rendered into tritium water in a recoupler and stored in a water storage apparatus. (Yoshino, Y.)

The projects for heavy water production of the Argentine National Atomic Energy Commission

International Nuclear Information System (INIS)

Garcia Bourg, J.M.; Garcia, E.E.

1982-01-01

The bases and scope of the projects for heavy water production that are being currently developed by the Argentine National Atomic Energy Commission (CNEA) are described. As an introduction, the following points are presented: a) the fundamentals of heavy water utilization in a nuclear reactor, with a mention of its properties and uses, b) a review of the physicochemical bases of the principal methods for heavy water production: chemical exchange (monothermal and bithermal processes), distillation and electrolysis, with tables summarizing the fundamental characteristics of the first two ones, and an evaluation of the different production methods from the viewpoint of their application in an industrial scale; and c) a synthetic information, in the form of tables, about the world's heavy water production. The subject of heavy water production in Argentina is treated in the principal section, describing the scope, location, main characteristics and chemical processes corresponding to the projects being developed by CNEA, which currently are the installation of an Industrial Plant in Arroyito (Province of Neuquen), purchased on a turnkey basis and using the NH 3 /H 2 isotopic exchange method; the installation of an Experimental Plant in Atucha (Province of Buenos Aires), for the development of the domestic technology of heavy-water production by the SH 2 /H 2 O isotopic exchange method, and the development of the engineering of an industrial plant (''Module 80''), based on the Experimental Plant's technology. (M.E.L.) [es

Safety Evaluation of Osun River Water Containing Heavy Metals and ...

African Journals Online (AJOL)

Summary: This study evaluated the pH, heavy metals and volatile organic compounds (VOCs) in Osun river water. It also evaluated its safety in rats. Heavy metals were determined by atomic absorption spectrophotometry (AAS) while VOCs were determined by gas chromatography coupled with flame ionization detector ...

Optical absorptions in ZnO/a-Si distributed Bragg reflectors

Energy Technology Data Exchange (ETDEWEB)

Chen, Aqing, E-mail: aqchen@hdu.edu.cn; Chen, Zhian [Hangzhou Dianzi University, College of Materials & Environmental Engineering (China); Zhu, Kaigui [Beihang University, Department of physics (China); Ji, Zhenguo [Hangzhou Dianzi University, College of Materials & Environmental Engineering (China)

2017-01-15

The distributed Bragg reflectors (DBRs) consisting of alternating layers of ZnO and heavy doped amorphous silicon (a-Si) have been fabricated by magnetron sputtering. It is novel to find that the optical absorptions exist in the stopband of the DBRs, and that many discrete strong optical absorption peaks exist in the wavelength range of visible to near-infrared. The calculated results by FDTD show that the absorptions in the stopband mainly exist in the first a-Si layer, and that the light absorbed by other a-Si layers inside contributes to the two absorption peaks in near-infrared range. The strong absorptions ranged from visible to infrared open new possibilities to the enhancement of the performance of amorphous silicon solar cells.

Surface Optimization Techniques for Deployable Reflectors, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Under this and several other programs, CTD has developed TEMBOREG deployable solid-surface reflectors (TEMBOREG Reflectors) to provide future NASA and Air Force...

Assessment of Heavy Metals in the Water of Sahastradhara Hill Stream at Dehradun, India

Directory of Open Access Journals (Sweden)

Pawan Kumar Bharti

2014-09-01

Full Text Available A study on heavy metals assessment in the water of Sahastradhara hill-stream was conducted with different five sites at significant differences. The present paper deals with the water quality status of Sahastradhara stream by the assessment of heavy metals. Heavy Metals were found in fluctuated trend from first upstream to last downstream. The values of almost all Heavy Metals were found in increasing manner especially after the fourth sampling site. After the third sampling station, a solid waste dumping site was found. So, there may be a relation between heavy metals in stream water and solid waste dumping site. Concentrations of all Heavy Metals at fourth and fifth sampling site were found very high. DOI: http://dx.doi.org/10.3126/ije.v3i3.11076 International Journal of Environment Vol.3(3 2014: 164-172

Electrolytic separation factors for oxygen isotopes in light and heavy water solutions

International Nuclear Information System (INIS)

Gulens, J.; Olmstead, W.J.; Longhurst, T.H.; Gale, K.L.; Rolston, J.H.

1987-01-01

The electrolytic separation factor, α, has been measured for /sup 17/O and /sup 18/O at Pt and Ni anodes in both light and heavy water solutions of 6M KOH as a function of current density. For oxygen-17, isotopic separation effects were not observed, within the experimental uncertainty of +-2%, under all conditions studied. For oxygen-18, there is a small difference of 2% in α values between Pt and Ni in both light and heavy water solutions, but there is no significant difference in α values between light and heavy water solutions. In light waters solutions, the separation factor at Pt is small, α(/sup 18/O) ≤ 1.02 for i ≥ 0.1 A/cm/sub 2/. This value agrees reasonably well with theoretical estimates

Pulse radiolysis studies of liquid heavy water at temperatures up to 250 degrees C

International Nuclear Information System (INIS)

Stuart, C.R.; Ouellette, D.C.; Elliot, A.J.

2002-09-01

This report documents the rate constants and associated activation energies for the reactions of the primary radical species, e aq - , ·OD and ·D, which are formed during the radiolysis of heavy water within the temperature range 20 to 250 o C. These heavy-water data have been compared with the corresponding information for light water. These kinetic data form part of the database that is required to model the aqueous radiation chemistry that occurs within the core of the heavy water cooled and moderated CANDU reactor. (author)

Pulse radiolysis studies of liquid heavy water at temperatures up to 250 degrees C

Energy Technology Data Exchange (ETDEWEB)

Stuart, C.R.; Ouellette, D.C.; Elliot, A.J

2002-09-01

This report documents the rate constants and associated activation energies for the reactions of the primary radical species, e{sub aq}{sup -}, {center_dot}OD and {center_dot}D, which are formed during the radiolysis of heavy water within the temperature range 20 to 250 {sup o}C. These heavy-water data have been compared with the corresponding information for light water. These kinetic data form part of the database that is required to model the aqueous radiation chemistry that occurs within the core of the heavy water cooled and moderated CANDU reactor. (author)

The Battle for Heavy Water Three physicists' heroic exploits

CERN Multimedia

2002-01-01

Up until the end of the 1970s you could still catch a glimpse of his massive silhouette in the corridors of CERN. Lew Kowarksi, one of the pioneers of the Laboratory, was not only a great physicist; he was also a genuine hero of World War II. In 1940, along with Frédéric Joliot and Hans von Halban, Lew Kowarski managed to get the entire world supply of heavy water away to safety from the Nazis after a fantastic escape from occupied France. At the end of the war, the three physicists played themselves in a film about their adventures entitled 'la Bataille de l'eau lourde'. This film, which has been loaned to us by the French National Film Library, will be shown at CERN for the first time next Thursday. At the beginning of the war, heavy water (D20, two atoms of deuterium and one oxygen atom) was of strategic importance. In 1939 Frédéric Joliot, aided by Hans von Halban and Lew Kowarski, demonstrated the nuclear chain reaction and the moderator role that heavy water plays in it. A few weeks before the inv...

Benchmarking the new JENDL-4.0 library on criticality experiments of a research reactor with oxide LEU (20 w/o) fuel, light water moderator and beryllium reflectors

International Nuclear Information System (INIS)

Liem, Peng Hong; Sembiring, Tagor Malem

2012-01-01

Highlights: ► Benchmark calculations of the new JENDL-4.0 library. ► Thermal research reactor with oxide LEU fuel, H 2 O moderator and Be reflector. ► JENDL-4.0 library shows better C/E values for criticality evaluations. - Abstract: Benchmark calculations of the new JENDL-4.0 library on the criticality experiments of a thermal research reactor with oxide low enriched uranium (LEU, 20 w/o) fuel, light water moderator and beryllium reflector (RSG GAS) have been conducted using a continuous energy Monte Carlo code, MVP-II. The JENDL-4.0 library shows better C/E values compared to the former library JENDL-3.3 and other world-widely used latest libraries (ENDF/B-VII.0 and JEFF-3.1).

Advanced reflector materials for solar concentrators

Science.gov (United States)

Jorgensen, Gary; Williams, Tom; Wendelin, Tim

1994-10-01

This paper describes the research and development at the US National Renewable Energy Laboratory (NREL) in advanced reflector materials for solar concentrators. NREL's research thrust is to develop solar reflector materials that maintain high specular reflectance for extended lifetimes under outdoor service conditions and whose cost is significantly lower than existing products. Much of this work has been in collaboration with private-sector companies that have extensive expertise in vacuum-coating and polymer-film technologies. Significant progress and other promising developments will be discussed. These are expected to lead to additional improvements needed to commercialize solar thermal concentration systems and make them economically attractive to the solar manufacturing industry. To explicitly demonstrate the optical durability of candidate reflector materials in real-world service conditions, a network of instrumented outdoor exposure sites has been activated.

Direct harvesting of Helium-3 (3He) from heavy water nuclear reactors

International Nuclear Information System (INIS)

Bentoumi, G.; Didsbury, R.; Jonkmans, G.; Rodrigo, L.; Sur, B.

2013-01-01

The thermal neutron activation of deuterium inside a heavy-water-moderated or -cooled nuclear reactor produces a build-up of tritium in the heavy water. The in situ decay of tritium can, for certain reactor types and operating conditions, produce potentially useable amounts of 3 He, which can be directly extracted via the heavy-water cover gas without first separating, collecting and storing tritium outside the reactor. It is estimated that the amount of 3 He available for recovery from the moderator cover gas of a 700 MWe class Pressurized Heavy Water Reactor (PHWR) ranges from 0.1 to 0.7 m 3 (STP) per annum, varying with the tritium activity buildup in the moderator. The harvesting of 3 He would generate approximately 12.7 m 3 (STP) of 3 He, worth more than $30M at current market rates, over a typical 25-year operating cycle of the PHWR. This paper discusses the production of 3 He in the moderator of a PHWR and its extraction from the 4 He moderator cover gas system using conventional methods. (author)

Reconfigurable antenna using plasma reflector

Science.gov (United States)

Jusoh, Mohd Taufik; Ahmad, Khairol Amali; Din, Muhammad Faiz Md; Hashim, Fakroul Ridzuan

2018-02-01

This paper presents the feasibility study and design of plasma implementation in industrial, scientific and medical (ISM) communication band. A reflector antenna with rounded shaped is proposed to collimate beam in particular direction radiated by a quarter wave antenna operating at 2.4GHz. The simulations result has shown that by using plasma as the reflector elements, the gain, directivity and radiation patterns are identical with metal elements with only small different in the broadside direction. The versatility of the antenna is achievable by introducing electrical reconfigurable option to change the beam pattern.

Special operations in the heavy water system, III-2; III-2 Posebne operacije u sistemu teske vode

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-07-01

Special operations in the heavy water system described in this chapter are as follows: treatment, drainage and pouring of heavy water, emptying of the heavy water system, cleaning and vacuuming of the heavy water system. [Serbo-Croat] Posebne operacije u sistemu teske vode opisane u ovom poglavlju su: tretiranje, dreniranje i razlivanje teske vode, praznjenje sistema teske vode, 'ispiranje' i vakumiranje sistema teske vode.

Improvements on heavy water separation technology by isotopic water-hydrogen sulfide exchange

International Nuclear Information System (INIS)

Peculea, M.

1987-01-01

A series of possible variance is presented for the heavy water separation technology by isotopic H 2 O-H 2 S exchange at dual temperatures. The critical study of these variants, which are considered as characteristic quantities for the isotopes transport (production) and the extraction level is related to a dual temperature plant fed by liquid and cold column, which is the up-to-date technology employed in all heavy water production plants as variants of following plants are studied: dual temperature plant with double feeding; dual-temperature plant with equilibrium column (booster); dual-temperature-dual-pressure plant. Attention is paid to the variant with equilibration column (booster), executed and tested at the State Committee for Nuclear Energy and to the dual-temperature-dual pressure plant which presents the highest efficiency. (author)

Surface Water Modeling Using an EPA Computer Code for Tritiated Waste Water Discharge from the heavy Water Facility

International Nuclear Information System (INIS)

Chen, K.F.

1998-06-01

Tritium releases from the D-Area Heavy Water Facilities to the Savannah River have been analyzed. The U.S. EPA WASP5 computer code was used to simulate surface water transport for tritium releases from the D-Area Drum Wash, Rework, and DW facilities. The WASP5 model was qualified with the 1993 tritium measurements at U.S. Highway 301. At the maximum tritiated waste water concentrations, the calculated tritium concentration in the Savannah River at U.S. Highway 301 due to concurrent releases from D-Area Heavy Water Facilities varies from 5.9 to 18.0 pCi/ml as a function of the operation conditions of these facilities. The calculated concentration becomes the lowest when the batch releases method for the Drum Wash Waste Tanks is adopted

Commissioning performance activities of Heavy Water Plant (Hazira) (Paper No. 1.4)

International Nuclear Information System (INIS)

Anon.

1992-01-01

Heavy Water Plant, Hazira is the fourth in the line of plants based on monothermal NH 3 -H 2 exchange process. The experience gained during operation of other heavy water plants is reflected in the construction, commissioning and operation of HWP, Hazira. This paper aims at outlining the strategy adopted for both commissioning and operation. (author)

Programmable logic controllers in Heavy Water Project, Manuguru (Paper No. 3.4)

International Nuclear Information System (INIS)

Gupta, S.C.; Bhaskar, R.; Maiti, A.; Venkatesu, G.; Satish, P.; Goel, R.K.

1992-01-01

Enhancement to plant operational flexibility has been achieved in Heavy Water Project, Manuguru by installing programmable logic controllers for its control equipment. The earlier sulfide based Heavy Water Plant, Kota is using relay logic and diode based program-matrix for binary controls. Performance improvement and advantages of PLC and experience in its operation are described. (author). 3 refs

Performance of a PV module augmented by a plane reflector

Energy Technology Data Exchange (ETDEWEB)

Ahmad, G. E; Hussein, H. M. S; Mohamad, M. A [Dokki, Giza (Egypt)

2000-07-01

This paper presents a comparative experimental study on the performance of a PV module augmented by a south facing titled plane reflector and another identical one without reflector. The tilt angles of the two PV modules and reflector overhang are selected to be according to a previous theoretical study by the authors. The reflector tilt angle has been changed once a month so that the reflected beams from the plane reflector cover the total surface area of the PV module all days of every month during the high solar radiation period (i.e. three hours before and after solar noon). The study has been carried out on the two PV modules for a complete year under the actual atmospheric conditions of Cairo, Egypt. The measuring system used in the study comprises a data acquisition system, a computer, an electronic load and weather station. The experimental results indicate that the plane reflector enhances the yearly output energy of the PV module y about 22%. [Spanish] Este articulo presenta un estudio comparativo experimental sobre el rendimiento de un modulo de PV aumentado por un reflector plano inclinado mirando hacia el sur y otro identico sin reflector. Los angulos de inclinacion de los dos modulos y el reflector sobresaliente se seleccionan para que esten de acuerdo con un estudio teorico previo hecho por los autores. El angulo de inclinacion del reflector se cambio una vez al mes de manera que los rayos reflejados por el reflector plano cubrieran el area total de la superficie del modulo de PV todos los dias de cada mes durante el periodo de radiacion alto (o sea tres horas antes y despues del medio dia solar). El estudio ha sido llevado a cabo en dos modulos de PV durante un ano completo bajo condiciones atmosfericas reales de El Cairo, Egipto. El sistema de medicion usado en el estudio comprende un sistema de adquisicion de datos, una computadora, una memoria electronica y una estacion climatologica. Los resultados experimentales indican que el reflector plano

Fluoride content in water in and around heavy water plant Manuguru colony

International Nuclear Information System (INIS)

Mohapatra, C.; Dubey, S.K.; Reddy, A.R.; Ravi Kumar, T.S.P.; Selvaraj, S.

1996-01-01

Fluoride concentration in water used for human consumption has significant importance with respect to its toxic effects. Hence there was a need for analysing fluoride concentration in drinking water primarily used at Heavy water Plant, Manuguru (HWP (M)) colony and its nearby villages. We found that at HWP (M) colony there is not much variation in the fluoride concentration. However, nearby villages are having wide variation from 0.79 to 5.1 ppm. (author). 5 refs., 1 tab

Assets optimization at Heavy Water Plants

International Nuclear Information System (INIS)

Hiremath, S.C.

2006-01-01

In the world where the fittest can only survive, manufacturing and production enterprises are under intense pressure to achieve maximum efficiency in each and every field related to the ultimate production of plant. The winners will be those that use their assets, i.e men, material, machinery and money most effectively. The objective is to optimize the utilization of all plant assets-from entire process lines to individual pressure vessels, piping, process machinery, and vital machine components. Assets of Heavy Water Plants mainly consist of Civil Structures, Equipment and Systems (Mechanical, Electrical) and Resources like Water, Energy and Environment

Features in ammonia plant for maximising heavy water production (Paper No. 2.10)

International Nuclear Information System (INIS)

Tangri, N.N.; Singh, R.J.; Mukherjee, P.K.; Mishra, B.N.

1992-01-01

Whenever an ammonia plant is linked with heavy water production, a system should be foreseen in the design stage itself for total conservation of D 2 in synthesis gas and zero D 2 loss. The process should ensure recycle of D 2 rich condensate within the front end. This alone would be the single most important factor for improving heavy water production rate. The synthesis loop pressure should be chosen keeping in view the interest of heavy water plant (HWP). With vast experience in engineering NH 3 and HWP plants, it is possible to integrate HWP requirements at the design stage itself. (author)

Urban water pollution by heavy metals and health implication in ...

African Journals Online (AJOL)

Studies of common heavy metals were conducted at Onitsha, Anambra State, the most urbanized city in Southeastern Nigeria. It was discovered that both surface and subsurface water were heavily polluted. Seven (7) heavy metals namely: arsenic (As+2), cadmium (Cd+2), lead (Pb+2), mercury (Hg+2), zinc (Zn+2), copper ...

APPLICATION OF QUATERNIONS FOR REFLECTOR PARAMETER

Directory of Open Access Journals (Sweden)

I. A. Konyakhin

2016-09-01

Full Text Available Subject of Research. The paper deals with application of quaternions for optimization of reflector parameters at autocollimation measurements in comparison with a matrix method. Computer-based results on the quaternionic models are presented that have given the possibility to determine conditions of measurement error reduction in view of apriori information on the rotation axis position. The practical synthesis technique for tetrahedron reflector parameters using found ratios is considered. Method. Originally, received conditions for reduction of autocollimation system measurement error are determined with the use of a matrix method for definition of an angular object position as a set of three equivalent consecutive turns about coordinate axes. At realization of these conditions the numerous recalculation of orientation parameters between various systems of coordinates is necessary that increases complexity and reduces resulting accuracy of autocollimation system at practical measurements. The method of quaternions gives the possibility to analyze the change of an absolute angular position in space, thus, there are conditions of accuracy increase regardless of the used systems of coordinates. Main Results. Researches on the mathematical model have shown, that the orthogonal arrangement of two basic constant directions for autocollimator tetrahedron reflector is optimal with respect to criterion of measurement error reduction at bisection arrangement of actual turn axis against them. Practical Relevance. On the basis of the found ratios between tetrahedron reflector angles and angles of its initial orientation parameters we have developed a practical method of reflector synthesis for autocollimation measurements in case of apriori information on an actual turn axis at monitoring measurements of the shaft or pipelines deformations.

49 CFR 393.26 - Requirements for reflectors.

Science.gov (United States)

2010-10-01

... case of motor vehicles so constructed that requirement for a 381 mm (15-inch) minimum height above the... used in lieu of reflex reflectors if the material as used on the vehicle, meets the performance... motor vehicle. (3) Such surfaces shall be at least 3 inches from any required lamp or reflector unless...

General description of advanced heavy water reactor

International Nuclear Information System (INIS)

Kakodkar, A.; Sinha, R.K.; Dhawan, M.L.

1999-01-01

Advanced Heavy Water Reactor is a boiling light water cooled, heavy water moderated and vertical pressure tube type reactor with its design optimised for utilisation of thorium for power generation. The core consists of (Th-U 233 )O 2 and (Th-Pu)O 2 fuel with a discharge burn up of 20,000 MWd/Te. This reactor incorporates several features to simplify the design, which eliminate certain systems and components. AHWR design is also optimised for easy replaceability of coolant channels, facilitation of in-service inspection and maintenance and ease of erection. The AHWR design also incorporates several passive systems for performing safety-related functions in the event of an accident. In case of LOCA, emergency coolant is injected through 4 accumulators of 260 m 3 capacity directly into the core. Gravity driven water pool of capacity 6000 m 3 serves to cool the core for 3 days without operator's intervention. Core submergence, passive containment isolation and passive containment cooling are the added features in AHWR. The paper describes the various process systems, core and fuel design, primary components and safety concepts of AHWR. Plant layout and technical data are also presented. The conceptual design of the reactor has been completed, and the detailed design and development is scheduled for completion in the year 2002. (author)

Heavy-water extraction from non-electrolytic hydrogen streams

International Nuclear Information System (INIS)

LeRoy, R.L.; Hammerli, M.; Butler, J.P.

1981-01-01

Heavy water may be produced from non-electrolytic hydrogen streams using a combined electrolysis and catalytic exchange process. The method comprises contacting feed water in a catalyst column with hydrogen gas originating partly from a non-electrolytic hydrogen stream and partly from an electrolytic hydrogen stream, so as to enrich the feed water with the deuterium extracted from both the non-electrolytic and electrolytic hydrogen gas, and passing the deuterium water to an electrolyser wherein the electrolytic hydrogen gas is generated and then fed through the catalyst column. (L.L.)

System concept for a moderate cost Large Deployable Reflector (LDR)

Science.gov (United States)

Swanson, P. N.; Breckinridge, J. B.; Diner, A.; Freeland, R. E.; Irace, W. R.; Mcelroy, P. M.; Meinel, A. B.; Tolivar, A. F.

1986-01-01

A study was carried out at JPL during the first quarter of 1985 to develop a system concept for NASA's LDR. Major features of the concept are a four-mirror, two-stage optical system; a lightweight structural composite segmented primary reflector; and a deployable truss backup structure with integral thermal shield. The two-stage optics uses active figure control at the quaternary reflector located at the primary reflector exit pupil, allowing the large primary to be passive. The lightweight composite reflector panels limit the short-wavelength operation to approximately 30 microns but reduce the total primary reflector weight by a factor of 3 to 4 over competing technologies. On-orbit thermal analysis indicates a primary reflector equilibrium temperature of less than 200 K with a maximum gradient of about 5 C across the 20-m aperture. Weight and volume estimates are consistent with a single Shuttle launch, and are based on Space Station assembly and checkout.

Environmental health scoping study at Bruce Heavy Water Plant

International Nuclear Information System (INIS)

Prior, M.; Mostrom, M.; Coppock, R.; Florence, Z.

1995-10-01

There are concerns that hydrogen sulfide released from the Heavy Water Plant near Kincardine, Ontario may be the cause of the mortalities and morbidities observed in a nearby flock of sheep. The Philosopher's Wool sheep farm is about four kilometres south-southeast of the Bruce Heavy Water Plant. Ontario Hydro, the owner and operator of the Bruce Heavy Water Plant, claims that hydrogen sulphide emissions from the Bruce Heavy Water Plant are within regulatory limits and well below levels that cause harm. Accordingly, the Atomic Energy Control Board commissioned the Alberta Environmental Centre, Alberta Department of Environmental Protection, to develop a scoping study for this environmental health issue. The first objective was to describe a field investigation model to define clearly the environmental health and operation of the sheep farm. The second objective was to describe possible exposure patterns and develop a holistic environmental pathway model. If appropriate, the third study objective was to describe animal models of the actual situation to elucidate specific aspects of the environmental health concerns. It was not the objective of this report to provide a definitive answer to the present environmental health issue. Ontario Hydro provided data to the Alberta Environmental Centre, as di the sheep farmer, the attending veterinarian, the University of Guelph study team, and the Atomic Energy Control Board. A six-tiered strategy of sequential evaluations of the ovine health problem is based on the multiple-response paradigm. It assumes the observed ovine health results are the result of multiple effector events. Each tier constitutes a separate, but inter-related, study. Sequential evaluation and feedback of each tier allow sound scientific judgements and efficient use of resources. (author). 59 refs., 11 tabs., 22 figs

Wirelessly Controllable Inflated Electroactive Polymer (EAP) Reflectors

Science.gov (United States)

Bao, Xiaoqi; Bar-Cohen, Yoseph; Chang, Zensheu; Sherrit, Stewart; Badescu, Mircea

2005-01-01

Inflatable membrane reflectors are attractive for deployable, large aperture, lightweight optical and microwave systems in micro-gravity space environment. However, any fabrication flaw or temperature variation may results in significant aberration of the surface. Even for a perfectly fabricated inflatable membrane mirror with uniform thickness, theory shows it will form a Hencky curve surface but a desired parabolic or spherical surface. Precision control of the surfaceshape of extremely flexible membrane structures is a critical challenge for the success of this technology. Wirelessly controllable inflated reflectors made of electroactive polymers (EAP) are proposed in this paper. A finite element model was configured to predict the behavior of the inflatable EAP membranes under pre-strains, pressures and distributed electric charges on the surface. To explore the controllability of the inflatable EAP reflectors, an iteration algorism was developed to find the required electric actuation for correcting the aberration of the Hencky curve to the desired parabolic curve. The correction capability of the reflectors with available EAP materials was explored numerically and is presented in this paper.

Solubilities of boric acid in heavy water

International Nuclear Information System (INIS)

Nakai, Shigetsugu; Aoi, Hideki; Hayashi, Ken-ichi; Katoh, Taizo; Watanabe, Takashi.

1988-01-01

A gravimetric analysis using meta-boric acid (HBO 2 or DBO 2 ) as a weighing form has been developed for solubility measurement. The method gave satisfactory results in preliminary measurement of solubilities of boric acid in light water. By using this method, the solubilities of 10 B enriched D 3 BO 3 in heavy water were measured. The results are as follows; 2.67 (7deg C), 3.52 (15deg C), 5.70 (30deg C), 8.87 (50deg C) and 12.92 (70deg C) w/o, respectively. These values are about 10% lower than those in light water. Thermodynamical consideration based on the data shows that boric acid is the water structure breaker. (author)

Pollution Status of Pakistan: A Retrospective Review on Heavy Metal Contamination of Water, Soil, and Vegetables

Directory of Open Access Journals (Sweden)

Amir Waseem

2014-01-01

Full Text Available Trace heavy metals, such as arsenic, cadmium, lead, chromium, nickel, and mercury, are important environmental pollutants, particularly in areas with high anthropogenic pressure. In addition to these metals, copper, manganese, iron, and zinc are also important trace micronutrients. The presence of trace heavy metals in the atmosphere, soil, and water can cause serious problems to all organisms, and the ubiquitous bioavailability of these heavy metal can result in bioaccumulation in the food chain which especially can be highly dangerous to human health. This study reviews the heavy metal contamination in several areas of Pakistan over the past few years, particularly to assess the heavy metal contamination in water (ground water, surface water, and waste water, soil, sediments, particulate matter, and vegetables. The listed contaminations affect the drinking water quality, ecological environment, and food chain. Moreover, the toxicity induced by contaminated water, soil, and vegetables poses serious threat to human health.

Neutron moderation in heavy water

International Nuclear Information System (INIS)

Assis, J.T. de.

1980-03-01

The calculation of the energetic spectrum of thermic neutrons in heavy water, according to the models of the differential cross section; is presented. Simplifications in the Butler model are suggested for the diminution of computer time. The results obtained are compared with experimental data and with the Brown - St.John model. This calculation has been done in 30 energy groups and within our limit of precision, the results with the models and simplifications present satisfactory values, allowing its inclusion in reactor codes. (Author) [pt

Effects of Radial Reflector Composition on Core Reactivity and Peak Power

International Nuclear Information System (INIS)

Park, Sang Yoon; Lee, Kyung Hoon; Song, Jae Seung

2007-10-01

The effects of radial SA-240 alloy shroud on core reactivity and peak power are evaluated. The existence of radial SA-240 alloy shroud makes reflector water volume decrease, so the thermal absorption cross section of radial reflector is lower than without SA-240 alloy shroud case. Finally, the cycle length is increased from 788 EFPD to 845 EFPD and the peak power is decreased from 1.66 to 1.49. In the case of without SA-240 alloy shroud, a new core loading pattern search has been performed. For the guarantee of the same equivalent cycle length of with SA-240 alloy shroud case, the enrichment of U-235 should be increased from 4.22 w/o to 4.68 w/o. The nuclear key safety parameters of new core loading pattern have been calculated and recorded for the future

Effects of Radial Reflector Composition on Core Reactivity and Peak Power

Energy Technology Data Exchange (ETDEWEB)

Park, Sang Yoon; Lee, Kyung Hoon; Song, Jae Seung

2007-10-15

The effects of radial SA-240 alloy shroud on core reactivity and peak power are evaluated. The existence of radial SA-240 alloy shroud makes reflector water volume decrease, so the thermal absorption cross section of radial reflector is lower than without SA-240 alloy shroud case. Finally, the cycle length is increased from 788 EFPD to 845 EFPD and the peak power is decreased from 1.66 to 1.49. In the case of without SA-240 alloy shroud, a new core loading pattern search has been performed. For the guarantee of the same equivalent cycle length of with SA-240 alloy shroud case, the enrichment of U-235 should be increased from 4.22 w/o to 4.68 w/o. The nuclear key safety parameters of new core loading pattern have been calculated and recorded for the future.

Deployable reflector configurations

Science.gov (United States)

Meinel, A. B.; Meinel, M. P.; Woolf, N. J.

Both the theoretical reasons for considering a non-circular format for the Large Deployable Reflector, and a potentially realizable concept for such a device, are discussed. The optimum systems for diffraction limited telescopes with incoherent detection have either a single filled aperture, or two such apertures as an interferometer to synthesize a larger aperture. For a single aperture of limited area, a reflector in the form of a slot can be used to give increased angular resolution. It is shown how a 20 x 8 meter telescope can be configured to fit the Space Shuttle bay, and deployed with relatively simple operations. The relationship between the sunshield design and the inclination of the orbit is discussed. The possible use of the LDR as a basic module to permit the construction of supergiant space telescopes and interferometers both for IR/submm studies and for the entire ultraviolet through mm wave spectral region is discussed.

Reactivity requirements and safety systems for heavy water reactors

International Nuclear Information System (INIS)

Kati, S.L.; Rustagi, R.S.

1977-01-01

The natural uranium fuelled pressurised heavy water reactors are currently being installed in India. In the design of nuclear reactors, adequate attention has to be given to the safety systems. In recent years, several design modifications having bearing on safety, in the reactor processes, protective and containment systems have been made. These have resulted either from new trends in safety and reliability standards or as a result of feed-back from operating reactors of this type. The significant areas of modifications that have been introduced in the design of Indian PHWR's are: sophisticated theoretical modelling of reactor accidents, reactivity control, two independent fast acting systems, full double containment and improved post-accident depressurisation and building clean-up. This paper brings out the evolution of design of safety systems for heavy water reactors. A short review of safety systems which have been used in different heavy water reactors, of varying sizes, has been made. In particular, the safety systems selected for the latest 235 MWe twin reactor unit station in Narora, in Northern India, have been discussed in detail. Research and Development efforts made in this connection are discussed. The experience of design and operation of the systems in Rajasthan and Kalpakkam reactors has also been outlined

Heavy-Water Power Reactors. Proceedings Of A Symposium

International Nuclear Information System (INIS)

1968-01-01

Proceedings of a Symposium organized by the IAEA and held in Vienna, 11-15 September 1967. The timeliness of the meeting was underlined by the large gathering of over 225 participants from 28 countries and three international organizations. Contents: Experience with heavy-water power and experimental reactors and projects (14 papers); New and advanced power reactor designs and concepts (8 papers); Development programmes and thorium cycle (9 papers); Economics and prospects of heavy-water power reactors (7 papers); Physics and fuel management (8 papers); Fuels (5 papers); Safety, control and engineering (6 papers); Panel discussion. Except for one Russian paper, which is published in English, each paper is in its original language (49 English and 8 French) and is preceded by an abstract in English with a second one in the original language if this is not English. Discussions are in English. (author)

Heavy-Water Power Reactors. Proceedings Of A Symposium

Energy Technology Data Exchange (ETDEWEB)

NONE

1968-04-15

Proceedings of a Symposium organized by the IAEA and held in Vienna, 11-15 September 1967. The timeliness of the meeting was underlined by the large gathering of over 225 participants from 28 countries and three international organizations. Contents: Experience with heavy-water power and experimental reactors and projects (14 papers); New and advanced power reactor designs and concepts (8 papers); Development programmes and thorium cycle (9 papers); Economics and prospects of heavy-water power reactors (7 papers); Physics and fuel management (8 papers); Fuels (5 papers); Safety, control and engineering (6 papers); Panel discussion. Except for one Russian paper, which is published in English, each paper is in its original language (49 English and 8 French) and is preceded by an abstract in English with a second one in the original language if this is not English. Discussions are in English. (author)

Laser reflector with an interference coating

International Nuclear Information System (INIS)

Vol'pyan, O D; Semenov, A A; Yakovlev, P P

1998-01-01

An analysis was made of the reflectivity of interference coatings intended for the use in optical pumping of solid-state lasers. Ruby and Nd 3+ :YAG lasers were used as models in comparative pumping efficiency measurements, carried out employing reflectors with interference and silver coatings. Estimates of the service life of reflectors with interference coatings were obtained. The power of a thermo-optical lens was reduced by the use of such coatings in cw lasers. (laser system components)

Disordered animal multilayer reflectors and the localization of light

Science.gov (United States)

Jordan, T. M.; Partridge, J. C.; Roberts, N. W.

2014-01-01

Multilayer optical reflectors constructed from ‘stacks’ of alternating layers of high and low refractive index dielectric materials are present in many animals. For example, stacks of guanine crystals with cytoplasm gaps occur within the skin and scales of fish, and stacks of protein platelets with cytoplasm gaps occur within the iridophores of cephalopods. Common to all these animal multilayer reflectors are different degrees of random variation in the thicknesses of the individual layers in the stack, ranging from highly periodic structures to strongly disordered systems. However, previous discussions of the optical effects of such thickness disorder have been made without quantitative reference to the propagation of light within the reflector. Here, we demonstrate that Anderson localization provides a general theoretical framework to explain the common coherent interference and optical properties of these biological reflectors. Firstly, we illustrate how the localization length enables the spectral properties of the reflections from more weakly disordered ‘coloured’ and more strongly disordered ‘silvery’ reflectors to be explained by the same physical process. Secondly, we show how the polarization properties of reflection can be controlled within guanine–cytoplasm reflectors, with an interplay of birefringence and thickness disorder explaining the origin of broadband polarization-insensitive reflectivity. PMID:25339688

Heavy metals in water, sediments and submerged macrophytes in ponds around the Dianchi Lake, China.

Science.gov (United States)

Wang, Zhixiu; Yao, Lu; Liu, Guihua; Liu, Wenzhi

2014-09-01

Through retaining runoff and pollutants such as heavy metals from surrounding landscapes, ponds around a lake play an important role in mitigating the impacts of human activities on lake ecosystems. In order to determine the potential for heavy metal accumulation of submerged macrophytes, we investigated the concentrations of 10 heavy metals (i.e., As, Cd, Co, Cr, Cu, Fe, Mn, Ni, Pb, and Zn) in water, sediments, and submerged macrophytes collected from 37 ponds around the Dianchi Lake in China. Our results showed that both water and sediments of these ponds were polluted by Pb. Water and sediments heavy metal concentrations in ponds received urban and agricultural runoff were not significantly higher than those in ponds received forest runoff. This result indicates that a large portion of heavy metals in these ponds may originate from atmospheric deposition and weathering of background soils. Positive relationships were found among heavy metal concentrations in submerged macrophytes, probably due to the coaccumulation of heavy metals. For most heavy metals, no significant relationships were found between submerged macrophytes and their water and sediment environments. The maximum concentrations of Cr, Fe and Ni in Ceratophyllum demersum were 4242, 16,429 and 2662mgkg(-1), respectively. The result suggests that C. demersum is a good candidate species for removing heavy metals from polluted aquatic environments. Copyright © 2014 Elsevier Inc. All rights reserved.

Localization of the pumping reflector for a Nd:YAG laser

Energy Technology Data Exchange (ETDEWEB)

Kim, Kwang Suk; Kim, Chul Joong [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1994-12-01

For the first year plan of this program, the pumping reflectors, which are gold plated reflectors and ceramic diffuse reflectors, of the Nd:YAG laser have been localized. The laser output performances with these reflectors have been investigated. Developed reflectors can be applied successfully to our commercialized Nd:YAG laser which was worked in previous project. We designed the optical pumping system with GaAlAs diode laser bar to improve the pumping efficiency. Moreover, we investigated a simple pumping technique without changing the fleshlamp, which makes the Nd:YAG laser operate in a cw, a pulsed, and a mixed of the two mode. We expert many new applications of this diversification of output pulse shapes in industry and in medicine. 38 figs, 9 tabs, 18 refs. (Author).

Accelerator driven heavy water blanket on circulating fuel

International Nuclear Information System (INIS)

Kazaritsky, V.D.; Blagovolin, P.P.; Mladov, V.R.; Okhlopkov, M.L.; Batyaev, V.F.; Stepanov, N.V.; Seliverstov, V.V.

1997-01-01

A conceptual design of a heavy water blanket with circulating fuel for an accelerator driven transmutation system is described. The hybrid system consists of a high-current linear accelerator of protons and 4 targets, each placed inside a subcritical blanket

Halden Boiling Water Reactor. Plant Performance and Heavy-Water Management

Energy Technology Data Exchange (ETDEWEB)

Aas, S.; Jamne, E.; Wullum, T.; Fjellestad, K. [Institutt for Atomenergi, OECD Halden Reactor Project, Halden (Norway)

1968-04-15

The Halden boiling heavy-water reactor, designed and built by the Norwegian Institutt for Atomenergi, has since June 1958 been operated as an international project. On its second charge the reactor was operated at power levels up to 25 MW and most of the time at a pressure of 28.5 kg/cm{sup 2}. During the period from July 1964 to December 1966 the plant availability was close to 64% including shutdowns because of test fuel failures and loading/unloading of fuel. Disregarding such stops, the availability was close to 90%. The average burnup of the core is about 6200 MWd/t UO{sub 2} : the most highly exposed elements have reached 10000 MWd/t UO{sub 2}. The transition temperature of the reactor tank has been followed closely. The results of the surveillance programme and the implication on the reactor operation are discussed. The reactor is located in a cave in a rock. Some experiences with such a containment are given. To locate failed test-fuel elements a fuel failure location system has been installed. A fission gas collection system has saved valuable reactor time during clean-up of the reactor system following test fuel failures. Apart from one incident with two of the control stations, the plant control and instrumentation systems have functioned satisfactorily. Two incidents with losses of 150 and 200 kg of heavy water have occurred. However, after improved methods for leakage detection had been developed, the losses have been kept better than 50 g/h . Since April 1962 the isotopic purity of the heavy water (14 t) has decreased from 99.75 to 99.62%. The tritium concentration is now slightly above 700 {mu}C/cm{sup 3}. This activity level has not created any serious operational or maintenance problems. An extensive series of water chemistry experiments has been performed to study the influence of various operating parameters on radiolytic gas formation. The main results of these experiments will be reported. Different materials such as mild steel, ferritic steel

Acoustic wave focusing in an ellipsoidal reflector for extracorporeal shock-wave lithotripsy

Science.gov (United States)

Lottati, Itzhak; Eidelman, Shmuel

1993-07-01

Simulations of acoustic wave focusing in an ellipsoidal reflector for extracorporeal shock-wave lithotripsy (ESWL) are presented. The simulations are done on a structured/unstructured grid with a modified Tait equation of state for water. The Euler equations are solved by applying a second-order Godunov method. The computed results compare very well with the experimental results.

Full reflector thickness and isolation thickness on neutron transport

International Nuclear Information System (INIS)

Sakai, Tomohiro; Naito, Yoshitaka; Komuro, Yuichi.

1988-08-01

A method to determine ''full reflector thickness'' and ''isolation thickness'', which is utilized for criticality safety evaluation on nuclear fuel facilities, was proposed in this paper. Firstly, a calculation was tryed to obtain the two kinds of thicknesses from the result of criticality calculations for a specific case. Then, two simple equations which calculates the two kinds of thicknesses were made from the relation between reflector (or isolator) thickness and k eff , and one-group diffusion theory. Finally, we proposed a new method to determine the thicknesses. From the method we proposed, ''full reflector thickness'' and ''isolation thickness'' can be obtain using the equations and migration length of the reflector (or isolator) and infinite and effective multiplication factor of the fuel. (author)

Advanced technology heavy water monitors offering reduced implementation costs

International Nuclear Information System (INIS)

Kalechstein, W.; Hippola, K.B.

1984-10-01

The development of second generation heavy water monitors for use at CANDU power stations and heavy water plants has been completed and the instruments brought to the stage of commercial availability. Applications of advanced technology and reduced utilization of custom manufactured components have together resulted in instruments that are less expensive to produce than the original monitors and do not require costly station services. The design has been tested on two prototypes and fully documented, including the inspection and test procedures required for manufacture to the CSA Z299.3 quality verfication program standard. Production of the new monitors by a commercial vendor (Barringer Research Ltd.) has begun and the first instrument is scheduled for delivery to CRNL's NRU reactor in late 1984

Concentration of Heavy Metals in Drinking Water from Urban Areas ...

African Journals Online (AJOL)

Bheema

drinking water treatment practices in the areas, which in turn have important human health implications. This study, therefore, recommends the government and other responsible authorities to take appropriate corrective measures. Key words: Drinking water quality, Heavy metals, Maximum admissible limit, World health.

Ray Tracing modelling of reflector for vertical bifacial panel

DEFF Research Database (Denmark)

Jakobsen, Michael Linde; Thorsteinsson, Sune; Poulsen, Peter Behrensdorff

2016-01-01

Bifacial solar panels have recently become a new attractive building block for PV systems. In this work we propose a reflector system for a vertical bifacial panel, and use ray tracing modelling to model the performance. Particularly, we investigate the impact of the reflector volume being filled...... with a refractive medium, and shows the refractive medium improves the reflector performance since it directs almost all the light incident on the incoming plane into the PV panel....

Simulation study of resonant reflector for S-band BWO

International Nuclear Information System (INIS)

Choyal, Y; Parmar, Nidhi; Saini, Ajay Kumar; Chhotray, S K; Bhat, K S; Kumar, Lalit

2012-01-01

This paper presents the result of simulation studies of resonant reflector used for reflection of backward wave in relativistic BWO. The resonant reflector is modelled and analyzed by CST MWS for TM 01 . A TM 01 mode is fed at the output end of the BWO and signal is observed at the cathode end. Results show that 90 percent of the backward TM 01 wave is get reflected back by the locked TM 02 mode in the resonant reflector.

Bandwidth Study of the Microwave Reflectors with Rectangular Corrugations

Science.gov (United States)

Zhang, Liang; He, Wenlong; Donaldson, Craig R.; Cross, Adrian W.

2016-09-01

The mode-selective microwave reflector with periodic rectangular corrugations in the inner surface of a circular metallic waveguide is studied in this paper. The relations between the bandwidth and reflection coefficient for different numbers of corrugation sections were studied through a global optimization method. Two types of reflectors were investigated. One does not consider the phase response and the other does. Both types of broadband reflectors operating at W-band were machined and measured to verify the numerical simulations.

Silica coated magnetite nanoparticles for removal of heavy metal ions from polluted waters

CERN Document Server

Dash, Monika

2013-01-01

Magnetic removal of Hg2+ and other heavy metal ions like Cd2+, Pb2+ etc. using silica coated magnetite particles from polluted waters is a current topic of active research to provide efficient water recycling and long term high quality water. The technique used to study the bonding characteristics of such kind of nanoparticles with the heavy metal ions is a very sensitive hyperfine specroscopy technique called the perturbed angular correlation technique (PAC).

Heavy water production by alkaline water electrolysis

International Nuclear Information System (INIS)

Kamath, Sachin; Sandeep, K.C.; Bhanja, Kalyan; Mohan, Sadhana; Sugilal, G.

2014-01-01

Several heavy water isotope production processes are reported in literature. Water electrolysis in combination with catalytic exchange CECE process is considered as a futuristic process to increase the throughput and reduce the cryogenic distillation load but the application is limited due to the high cost of electricity. Any improvement in the efficiency of electrolyzers would make this process more attractive. The efficiency of alkaline water electrolysis is governed by various phenomena such as activation polarization, ohmic polarization and concentration polarization in the cell. A systematic study on the effect of these factors can lead to methods for improving the efficiency of the electrolyzer. A bipolar and compact type arrangement of the alkaline water electrolyzer leads to increased efficiency and reduced inventory in comparison to uni-polar tank type electrolyzers. The bipolar type arrangement is formed when a number of single cells are stacked together. Although a few experimental studies have been reported in the open literature, CFD simulation of a bipolar compact alkaline water electrolyzer with porous electrodes is not readily available.The principal aim of this study is to simulate the characteristics of a single cell compact electrolyzer unit. The simulation can be used to predict the Voltage-Current Density (V-I) characteristics, which is a measure of the efficiency of the process.The model equations were solved using COMSOL multi-physics software. The simulated V-I characteristic is compared with the experimental data

Performance of refractometry in quantitative estimation of isotopic concentration of heavy water in nuclear reactor

International Nuclear Information System (INIS)

Dhole, K.; Roy, M.; Ghosh, S.; Datta, A.; Tripathy, M.K.; Bose, H.

2013-01-01

Highlights: ► Rapid analysis of heavy water samples, with precise temperature control. ► Entire composition range covered. ► Both variations in mole and wt.% of D 2 O in the heavy water sample studied. ► Standard error of calibration and prediction were estimated. - Abstract: The method of refractometry has been investigated for the quantitative estimation of isotopic concentration of heavy water (D 2 O) in a simulated water sample. Feasibility of refractometry as an excellent analytical technique for rapid and non-invasive determination of D 2 O concentration in water samples has been amply demonstrated. Temperature of the samples has been precisely controlled to eliminate the effect of temperature fluctuation on refractive index measurement. The method is found to exhibit a reasonable analytical response to its calibration performance over the purity range of 0–100% D 2 O. An accuracy of below ±1% in the measurement of isotopic purity of heavy water for the entire range could be achieved

Heavy metal pollution in drinking water - a global risk for human ...

African Journals Online (AJOL)

Water resources in the world have been profoundly influenced over the last years by human activities, whereby the world is currently facing critical water supply and drinking water quality problems. In many parts of the world heavy metal (HM) concentrations in drinking water are higher than some international guideline ...

DEGRADATION EVALUATION OF HEAVY WATER DRUMS AND TANKS

Energy Technology Data Exchange (ETDEWEB)

Mickalonis, J.; Vormelker, P.

2009-07-31

Heavy water with varying chemistries is currently being stored in over 6700 drums in L- and K-areas and in seven tanks in L-, K-, and C-areas. A detailed evaluation of the potential degradation of the drums and tanks, specific to their design and service conditions, has been performed to support the demonstration of their integrity throughout the desired storage period. The 55-gallon drums are of several designs with Type 304 stainless steel as the material of construction. The tanks have capacities ranging from 8000 to 45600 gallons and are made of Type 304 stainless steel. The drums and tanks were designed and fabricated to national regulations, codes and standards per procurement specifications for the Savannah River Site. The drums have had approximately 25 leakage failures over their 50+ years of use with the last drum failure occurring in 2003. The tanks have experienced no leaks to date. The failures in the drums have occurred principally near the bottom weld, which attaches the bottom to the drum sidewall. Failures have occurred by pitting, crevice and stress corrosion cracking and are attributable, in part, to the presence of chloride ions in the heavy water. Probable degradation mechanisms for the continued storage of heavy water were evaluated that could lead to future failures in the drum or tanks. This evaluation will be used to support establishment of an inspection plan which will include susceptible locations, methods, and frequencies for the drums and tanks to avoid future leakage failures.

AECB staff annual report of Bruce Heavy Water Plant operation for the year 1991

International Nuclear Information System (INIS)

1992-11-01

Bruce Heavy Water Plant operation was acceptably safe in 1991. There were no breaches of any of the regulations issued under the authority of the Atomic Energy Control Act. There was one violation of the operating licence. For one hour on October 30, 1991, water leaving the plant contained more hydrogen sulphide than Ontario regulations allow. There was no threat to public health or safety or harm to the environment as a result of this violation. One worker was overcome by hydrogen sulphide. The worker did not lose consciousness, but had the symptoms of H 2 S poisoning. Ontario Hydro took actions to increase awareness of the Operating Policy and Principles at Bruce Heavy Water Plant during 1991. All personnel attended a training course, and Ontario Hydro is reviewing all Bruce Heavy Water Plant documentation to ensure it is consistent with the Operating Policies and Principles. Ontario Hydro met 13 of 15 safety-related system availability targets. The AECB is satisfied appropriate action is being taken to improve the performance of the other two systems. Ontario Hydro continued to put heavy emphasis on safety training; however, they did not meet some of their other training targets. Ontario Hydro completed all of the planned emergency exercises at Bruce Heavy Water Plant in 1991. (Author)

Significant Features of Warm Season Water Vapor Flux Related to Heavy Rainfall and Draught in Japan

Science.gov (United States)

Nishiyama, Koji; Iseri, Yoshihiko; Jinno, Kenji

2009-11-01

In this study, our objective is to reveal complicated relationships between spatial water vapor inflow patterns and heavy rainfall activities in Kyushu located in the western part of Japan, using the outcomes of pattern recognition of water vapor inflow, based on the Self-Organizing Map. Consequently, it could be confirmed that water vapor inflow patterns control the distribution and the frequency of heavy rainfall depending on the direction of their fluxes and the intensity of Precipitable water. Historically serious flood disasters in South Kyushu in 1993 were characterized by high frequency of the water vapor inflow patterns linking to heavy rainfall. On the other hand, severe draught in 1994 was characterized by inactive frontal activity that do not related to heavy rainfall.

Impact analysis and testing of tritiated heavy water transportation packages including hydrodynamic effects

International Nuclear Information System (INIS)

Sauve, R.G.; Tulk, J.D.; Gavin, M.E.

1989-01-01

Ontario Hydro has recently designed a new Type B(M) Tritiated Heavy Water Transportation Package (THWTP) for the road transportation of tritiated heavy water from its operating nuclear stations to the Tritium Removal Facility in Ontario. These packages must demonstrate the ability to withstand severe shock and impact scenarios such as those prescribed by IAEA standards. The package, shown in figure 1, comprises an inner container filled with tritiated heavy water, and a 19 lb/ft 3 polyurethane foam-filled overpack. The overpack is of sandwich construction with 304L stainless steel liners and 10.5 inch thick nominal foam walls. The outer shell is 0.75 inch thick and the inner shell is 0.25 inch thick. The primary containment boundary consists of the overpack inner liner, the containment lid and outer containment seals in the lid region. The total weight of the container including the 12,000 lb. payload is 36,700 lb. The objective of the present study is to evaluate the hydrodynamic effect of the tritiated heavy water payload on the structural integrity of the THWTP during a flat end drop from a height of 9 m. The study consisted of three phases: (i) developing an analytical model to simulate the hydrodynamic effects of the heavy water payload during impact; (ii) performing an impact analysis for a 9 m flat end drop of the THWTP including fluid structure interaction; (iii) verification of the analytical models by experiment

Tritium separation from heavy water by electrolysis with solid polymer electrolyte

International Nuclear Information System (INIS)

Ogata, Y.; Ohtani, N.; Kotaka, M.

2003-01-01

A tritium separation from heavy water by electrolysis using a solid polymer electrode layer was specified. The cathode was made of stainless steel or nickel. The electrolysis was performed for 1 hour at 5, 10, 20, and 30 deg C. Using a palladium catalyst, generated hydrogen and oxygen gases were recombined, which was collected with a cold trap. The activities of the samples were measured by a liquid scintillation counter. The apparent tritium separation factors of the heavy and light water at 20 deg C were ∼2 and ∼12, respectively. (author)

Improvements done at Heavy Water Plant (Manuguru) to increase the standards of environmental protection

International Nuclear Information System (INIS)

Rama Rao, V.V.S.; Gupta, R.V.; Pandey, B.L.

1997-01-01

The Heavy Water Plant at Manuguru is designed to produce 185 MTY of nuclear grade heavy water based on bithermal H 2 S-H 2 O exchange process and handles large inventory of H 2 S gas (about 400 MT). As H 2 S gas is very toxic, corrosive and hazardous in nature, extreme care has been taken in the design of plant, selection of equipment and materials adhering to stringent fabrication procedures and codes to ensure the production of heavy water in a safe manner. This paper highlights the improvements done at Heavy Water Plant (Manuguru) to increase the standards of environmental protection. The safety assessment of a hazardous plant is a continuous process. Apart from the extreme care taken in the design, construction, commissioning and operation of the plant, review of each and every safety related unusual occurrence by various levels of review committees as stipulated and speedy implementation of the recommendations goes in a long way in increasing the standards of environmental protection

Ultrabroadband Hybrid III-V/SOI Grating Reflector for On-chip Lasers

DEFF Research Database (Denmark)

Park, Gyeong Cheol; Taghizadeh, Alireza; Chung, Il-Sug

2016-01-01

We report on a new type of III-V/SOI grating reflector with a broad stopband of 350 nm. This reflector has promising prospects for applications in high-speed III-V/SOI vertical cavity lasers with an improved heat dissipation capability.......We report on a new type of III-V/SOI grating reflector with a broad stopband of 350 nm. This reflector has promising prospects for applications in high-speed III-V/SOI vertical cavity lasers with an improved heat dissipation capability....

Removal of Heavy Metals from Drinking Water by Magnetic Carbon Nanostructures Prepared from Biomass

OpenAIRE

Muneeb Ur Rahman Khattak, Muhammad; Zahoor, Muhammad; Muhammad, Bakhtiar; Khan, Farhat Ali; Ullah, Riaz; AbdEI-Salam, Naser M.

2017-01-01

Heavy metals contamination of drinking water has significant adverse effects on human health due to their toxic nature. In this study a new adsorbent, magnetic graphitic nanostructures were prepared from watermelon waste. The adsorbent was characterized by different instrumental techniques (surface area analyzer, FTIR, XRD, EDX, SEM, and TG/DTA) and was used for the removal of heavy metals (As, Cr, Cu, Pb, and Zn) from water. The adsorption parameters were determined for heavy metals adsorpti...

Graphite-moderated and heavy water-moderated spectral shift controlled reactors

International Nuclear Information System (INIS)

Alcala Ruiz, F.

1984-01-01

It has been studied the physical mechanisms related with the spectral shift control method and their general positive effects on economical and non-proliferant aspects (extension of the fuel cycle length and low proliferation index). This methods has been extended to non-hydrogenous fuel cells of high moderator/fuel ratio: heavy water cells have been con- trolled by graphite rods graphite-moderated and gas-cooled cells have been controlled by berylium rods and graphite-moderated and water-cooled cells have been controlled by a changing mixture of heavy and light water. It has been carried out neutron and thermal analysis on a pre design of these types of fuel cells. We have studied its neutron optimization and their fuel cycles, temperature coefficients and proliferation indices. Finally, we have carried out a comparative analysis of the fuel cycles of conventionally controlled PWRs and graphite-moderated, water-cooled and spectral shift controlled reactors. (Author) 71 refs

Effective management of water systems in a chemical industry: a case study at Heavy Water Plant, Manuguru

International Nuclear Information System (INIS)

Prahalad, B.; Pandey, B.L.

1997-01-01

This paper describes about the important methods of water management in general followed by a description of the water system and measures taken/to be implemented at Heavy Water Plant, Manuguru in particular in order to effectively tackle the effluent water by reuse of the treated effluents

The geometrical theory of diffraction for axially symmetric reflectors

DEFF Research Database (Denmark)

Rusch, W.; Sørensen, O.

1975-01-01

The geometrical theory of diffraction (GTD) (cf. [1], for example) may be applied advantageously to many axially symmetric reflector antenna geometries. The material in this communication presents analytical, computational, and experimental results for commonly encountered reflector geometries...

Convergence studies of deterministic methods for LWR explicit reflector methodology

International Nuclear Information System (INIS)

Canepa, S.; Hursin, M.; Ferroukhi, H.; Pautz, A.

2013-01-01

The standard approach in modem 3-D core simulators, employed either for steady-state or transient simulations, is to use Albedo coefficients or explicit reflectors at the core axial and radial boundaries. In the latter approach, few-group homogenized nuclear data are a priori produced with lattice transport codes using 2-D reflector models. Recently, the explicit reflector methodology of the deterministic CASMO-4/SIMULATE-3 code system was identified to potentially constitute one of the main sources of errors for core analyses of the Swiss operating LWRs, which are all belonging to GII design. Considering that some of the new GIII designs will rely on very different reflector concepts, a review and assessment of the reflector methodology for various LWR designs appeared as relevant. Therefore, the purpose of this paper is to first recall the concepts of the explicit reflector modelling approach as employed by CASMO/SIMULATE. Then, for selected reflector configurations representative of both GII and GUI designs, a benchmarking of the few-group nuclear data produced with the deterministic lattice code CASMO-4 and its successor CASMO-5, is conducted. On this basis, a convergence study with regards to geometrical requirements when using deterministic methods with 2-D homogenous models is conducted and the effect on the downstream 3-D core analysis accuracy is evaluated for a typical GII deflector design in order to assess the results against available plant measurements. (authors)

Physical and water properties of selected Polish heavy soils of various origins

Directory of Open Access Journals (Sweden)

Kaczmarek Zbigniew

2015-12-01

Full Text Available The paper presents the characteristics of selected physical, chemical, and water properties of four mineral arable soils characterized with heavy and very heavy texture. Soil samples from genetic horizons of black earths from areas near Kętrzyn, Gniew and Kujawy, and alluvial soils from Żuławy were used. The following properties were determined in the samples of undisturbed and disturbed structure: texture, particle density, bulk density, porosity, natural and hygroscopic moistures, maximal hygroscopic capacity, saturated hydraulic conductivity, potential of water bonding in soil, total and readily available water, total retention in the horizon of 0–50 cm, drainage porosity, content of organic carbon and total nitrogen Parent rocks of these soils were clays, silts and loams of various origin. High content of clay fraction strongly influenced the values of all the analyzed properties. All the examined soils had high content of organic carbon and total nitrogen and reaction close to neutral or alkaline. High content of mineral and organic colloids and, what follows, beneficial state of top horizons’ structure, determined – apart from heavy texture – low soil bulk density and high porosity. The investigated soils were characterized by high field water capacity and wide scopes of total and readily available water. The saturated hydraulic conductivity was low and characteristic to heavy mineral arable soils. The parameter which influenced the variability of analyzed parameters most was texture.

Assessment of heavy metal pollution in drinking water due to mining ...

African Journals Online (AJOL)

Mining and smelting activities are the main causes for the increasing pollution of heavy metals from water sources. The toxicity of these heavy metals from the mining, milling and smelting companies can cause harmful and even lethal effects on the human health. The objective of this study was to investigate the level of As, ...

Health risks associated with heavy metals in the drinking water of Swat, northern Pakistan.

Science.gov (United States)

Lu, Yonglong; Khan, Hizbullah; Zakir, Shahida; Ihsanullah; Khan, Sardar; Khan, Akbar Ali; Wei, Luo; Wang, Tieyu

2013-10-01

The concentrations of heavy metals such as Cd, Cr, Cu, Mn, Ni, Pb and Zn were investigated in drinking water sources (surface and groundwater) collected from Swat valley, Khyber Pakhtunkhwa, Pakistan. The potential health risks of heavy metals to the local population and their possible source apportionment were also studied. Heavy metal concentrations were analysed using atomic absorption spectrometer and compared with permissible limits set by Pakistan Environmental Protection Agency and World Health Organization. The concentrations of Cd, Cr, Ni and Pb were higher than their respective permissible limits, while Cu, Mn and Zn concentrations were observed within their respective limits. Health risk indicators such as chronic daily intake (CDI) and health risk index (HRI) were calculated for adults and children separately. CDIs and HRIs of heavy metals were found in the order of Cr > Mn > Ni > Zn > Cd > Cu > Pb and Cd > Ni > Mn > Cr > Cu > Pb > Zn, respectively. HRIs of selected heavy metals in the drinking water were less than 1, indicating no health risk to the local people. Multivariate and univariate statistical analyses showed that geologic and anthropogenic activities were the possible sources of water contamination with heavy metals in the study area.

A Nonlinear Dynamic Model and Free Vibration Analysis of Deployable Mesh Reflectors

Science.gov (United States)

Shi, H.; Yang, B.; Thomson, M.; Fang, H.

2011-01-01

This paper presents a dynamic model of deployable mesh reflectors, in which geometric and material nonlinearities of such a space structure are fully described. Then, by linearization around an equilibrium configuration of the reflector structure, a linearized model is obtained. With this linearized model, the natural frequencies and mode shapes of a reflector can be computed. The nonlinear dynamic model of deployable mesh reflectors is verified by using commercial finite element software in numerical simulation. As shall be seen, the proposed nonlinear model is useful for shape (surface) control of deployable mesh reflectors under thermal loads.

Feasibility study of fusion breeding blanket concept employing graphite reflector

International Nuclear Information System (INIS)

Cho, Seungyon; Ahn, Mu-Young; Lee, Cheol Woo; Kim, Eung Seon; Park, Yi-Hyun; Lee, Youngmin; Lee, Dong Won

2015-01-01

Highlights: • A Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept adopts graphite as a reflector material by reducing the amount of beryllium multiplier. • Its feasibility was investigated in view point of the nuclear performance as well as material-related issues. • A nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket. • Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions. • In conclusion, the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition. - Abstract: To obtain high tritium breeding performance with limited blanket thickness, most of solid breeder blanket concepts employ a combination of lithium ceramic as a breeder and beryllium as a multiplier. In this case, considering that huge amount of beryllium are needed in fusion power plants, its handling difficulty and cost can be a major factor to be accounted for commercial use. Korea has proposed a Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept relevant to fusion power plants. Here, graphite is used as a reflector material by reducing the amount of beryllium multiplier. Its feasibility has been investigated in view point of the nuclear performance as well as material-related issues. In this paper, a nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket, considering tritium breeding capability and neutron shielding and activation aspects. Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions, resulting in that the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition.

Feasibility study of fusion breeding blanket concept employing graphite reflector

Energy Technology Data Exchange (ETDEWEB)

Cho, Seungyon, E-mail: sycho@nfri.re.kr [National Fusion Research Institute, Daejeon (Korea, Republic of); Ahn, Mu-Young [National Fusion Research Institute, Daejeon (Korea, Republic of); Lee, Cheol Woo; Kim, Eung Seon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Park, Yi-Hyun; Lee, Youngmin [National Fusion Research Institute, Daejeon (Korea, Republic of); Lee, Dong Won [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2015-10-15

Highlights: • A Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept adopts graphite as a reflector material by reducing the amount of beryllium multiplier. • Its feasibility was investigated in view point of the nuclear performance as well as material-related issues. • A nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket. • Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions. • In conclusion, the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition. - Abstract: To obtain high tritium breeding performance with limited blanket thickness, most of solid breeder blanket concepts employ a combination of lithium ceramic as a breeder and beryllium as a multiplier. In this case, considering that huge amount of beryllium are needed in fusion power plants, its handling difficulty and cost can be a major factor to be accounted for commercial use. Korea has proposed a Helium-Cooled Ceramic Reflector (HCCR) breeding blanket concept relevant to fusion power plants. Here, graphite is used as a reflector material by reducing the amount of beryllium multiplier. Its feasibility has been investigated in view point of the nuclear performance as well as material-related issues. In this paper, a nuclear analysis is performed under the fusion reactor condition to address the feasibility of graphite reflector in breeding blanket, considering tritium breeding capability and neutron shielding and activation aspects. Also, the chemical stability of the graphite is investigated considering the chemical stability under accident conditions, resulting in that the adaptation of graphite reflector in breeding blanket is intrinsically safe and plausible under fusion reactor condition.

Remote handling design for moderator-reflector maintenance in JSNS

International Nuclear Information System (INIS)

Teshigawara, Makoto; Aizawa, Hideyuki; Harada, Masahide; Kinoshita, Hidetaka; Meigo, Shinichiro; Maekawa, Fujio; Kaminaga, Masanori; Kato, Takashi; Ikeda, Yujiro

2005-05-01

This report introduces the present design status of remote-handling devices for activated and used components such as moderator and reflector in a spallation neutron source of the Material and Life Science Facility (MLF) at J-PARC (Japan Proton Accelerator Research Complex). The design concept and maintenance scenario are also mentioned. A key maintenance scenario adopts that the used components should be taken out from the MLF to the other storage facility after the volume reduction of them. Almost full remote handling is available to the maintenance work except for the connection/disconnection pipes of the cooling water. Remote handling for the cooling water system is under designing and it will be prepared before being significant radiation dose by accumulation of beryllium ( 7 Be) in future. Total six remote handling devices are used for moderator-reflector maintenance. They are also available to the proton beam window and muon target maintenance. Maintenance scenario is separated into two works. One is to replace used components to new ones during beam-stop and the other is dispose used components during beam operation. Required period of replacement work is estimated to be ∼15 days, on the other hand, the disposal work is ∼26 days after dry up work (∼30 days), respectively. Study of the maintenance scenario and the remote handling design brings about the reasonable procedures and period of the maintenance work. (author)

Long term assurance of supply of heavy water

International Nuclear Information System (INIS)

1978-01-01

The answer of Switzerland and Great Britain to a number of questions concerning the long-term assurance of the supply of heavy water are presented. The original problems are seen in the wider context of raw materials supply and its assurance in general. Non-proliferation aspects are touched

On-line infrared heavy-water instruments: status, economics and prospects

International Nuclear Information System (INIS)

Lynch, G.F.

1978-06-01

An intensive program to rehabilitate and establish the reliability of on-line heavy-water monitors is now showing tangible results. After determining the operating specifications and characteristics of the infrared D 2 O analyzers manufactured by Barringer Research Limited, monitoring systems based on these instruments were installed and commissioned at reactors and heavy-water plants. Ten such systems are currently operating reliably in the field. Laboratory tests and field experience have identified design features which would make the analyzers more convenient to use and less sensitive to environmental conditions. The conceptual design of a new instrument which is less dependent on station services and more tolerant of plant conditions has been completed

CANDU - Canadian experience and expectations with the heavy-water reactor

International Nuclear Information System (INIS)

Foster, J.S.; Russell, S.H.

1977-05-01

The paper describes the evolution of the CANDU nuclear-power plants with particular reference to the objectives of safety, reliability and economy; the development of industrial capacity for the supply of fuel, components and heavy water; and the prospective development of advanced fuel cycles and the projected results. It provides data on radiation, releases, and exposures, internal and external to the power plants; plant availability, capacity factors and other performance data; heavy water production data with reference to safety, reliability, and economics; projections of the performance of CANDU reactors operating on a thorium-U-233 cycle and the development required to establish this cycle; and intent with respct to spent-fuel management and radioactive-waste storage. (author)

Benchmark testing of Canadol-2.1 for heavy water reactor

International Nuclear Information System (INIS)

Liu Ping

1999-01-01

The new version evaluated nuclear data library of ENDF-B 6.5 has been released recently. In order to compare the quality of evaluated nuclear data CENDL-2.1 with ENDF-B 6.5, it is necessary to do benchmarks testing for them. In this work, CENDL-2.1 and ENDF-B 6.5 were used to generated the WIMS-69 group library respectively, and benchmarks testing was done for the heavy water reactor, using WIMS5A code. It is obvious that data files of CENDL-2.1 is better than that of old WIMS library for the heavy water reactors calculations, and is in good agreement with those of ENDF-B 6.5

[Heavy metals in environmental media around drinking water conservation area of Shanghai].

Science.gov (United States)

Shi, Gui-Tao; Chen, Zhen-Lou; Zhang, Cui; Bi, Chun-Juan; Cheng, Chen; Teng, Ji-Yan; Shen, Jun; Wang, Dong-Qi; Xu, Shi-Yuan

2008-07-01

The levels of heavy metals in Shanghai drinking water conservation area were determined, and the spatial distributions and main sources of heavy metals were investigated. Moreover, the ecological risk assessment of heavy metals was conducted. Some conclusions can be drawn as follows: (1) The average concentrations of Cd, Hg, Pb, Cu, Zn, Ni, Cr and As in road dust were 0.80, 0.23, 148.45, 127.52, 380.57, 63.17, 250.38 and 10.37 mg x kg(-1) respectively. In terms of the pollution level, the values of soils were relatively lower, with the mean contents of 0.16 (Cd), 0.33 (Hg), 30.14 (Pb), 30.66 (Cu), 103.79 (Zn), 24.04 (Ni), 65.75 (Cr) and 6.31 mg x kg(-1) (As) severally; meanwhile the average levels of heavy metals in vegetables were 0.010 (Cd), 0.016 (Hg), 0.36 (Pb), 12.80 (Cu), 61.69 (Zn), 2.04 (Ni), 2.41 (Cr) and 0.039 mg x kg(-1) (As) respectively. (2) Semivariogram and multivariate analysis indicated that heavy metals pollution of soils was induced by anthropogenic activities mostly, and the pollutants produced by traffic were the major source of heavy metals in road dust. (3) The order for heavy metal enrichment coefficients of vegetables was as following: Zn (0.589) > Cu (0.412) > 0.102 (Ni) > Cd (0.059) > Cr (0.061) > Hg (0.056) > Pb (0.012) > As (0.007), and the results indicated that Cd and Zn in vegetables were mainly from the soils, and the other metals were probably from the pollutants in the atmosphere. (4) Sediments in drinking water conservation area were probably derived from soils around; however, there was no significant relationship between heavy metals contents of them. (5) The results of ecological risk assessment of heavy metals showed that heavy metals in soils were in no-warning to warning situation, and warning to light-warning situation for road dust and vegetables. The fuzzy synthesis judgment for all the environmental media around drinking water conservation area was warning to light-warning.

Growth scenarios with thorium fuel cycles in pressurised heavy water reactors

International Nuclear Information System (INIS)

Balakrishnan, M.R.

1991-01-01

Since India has generous deposits of thorium, the availability of thorium will not be a limiting factor in any growth scenario. It is fairly well accepted that the best system for utilisation of thorium is the heavy water reactor. The growth scenarios possible using thorium in HWRs are considered. The base has been taken as 50,000 tons of natural uranium and practically unlimited thorium. The reference reactor has been assumed to be the PHWR, and all other growth scenarios are compared with the growth scenario provided by the once-through natural cycle in the PHWR. Two reactor types have been considered: the heavy water moderated, heavy water cooled, pressure tube reactor, known as the PHWR; and the heavy water moderated and cooled pressure vessel kind, similar to the ATUCHA reactor in Argentina. For each reactor, a number of different fuel cycles have been studied. All these cycles have been based on thorium. These are: the self-sustaining equilibrium thorium cycle (SSET); the high conversion ratio high burnup cycle; and the once through thorium cycle (OTT). The cycle have been initiated in two ways: one is by starting the cycle with natural uranium, reprocessing the spent fuel to obtain plutonium, and use that plutonium to initiate the thorium cycle; the other is to enrich the uranium to about 2-3% U-235 (the so-called Low Enriched Uranium or LEU), and use the LEU to initiate the thorium cycle. Both cases have been studied, and growth scenarios have been projected for every one of the possible combinations. (author). 1 tab

Heavy metal contamination in stream water and sediments of gold ...

African Journals Online (AJOL)

This study assessed the seasonal variation in heavy metal contamination of stream water and sediments in the gold mining area of Atakunmosa West local Government, Osun State, Nigeria. Twelve villages of prominence in illegal gold mining were selected for the study covering dry and wet seasons of 2012. Stream water ...

The density behaviour of heavy oils in water

International Nuclear Information System (INIS)

Fingas, M.; Hollebone, B.; Fieldhouse, B.

2006-01-01

The recent concern regarding the difficulty of cleaning up Low API gravity oils (LAPIO) spilled in water was discussed. Sinking and overwashing are 2 phenomena related to the behaviour of these heavy oils in water. Sinking refers to the complete submergence of the oil to the bottom of a waterbody, while over-washing refers to the overflowing of a layer of water over dense oil at sea when the oil is still close to the surface. The latter is important because even a micron-layer of water could render the oil undetectable, particularly at acute viewing angles, such as from a ship. This paper reviewed the properties of heavy oil, the prediction of density changes and the sinking/over-washing of heavy oil. In particular, it discussed a spill which occurred in August 2005 when 11 tank cars from train derailment spilled 800,000 litres of Bunker fuel mixed with high PAH-containing pole-treating oil into Lake Wabamun, Alberta. The behaviour of the oil included submergence, neutral buoyancy, resurfacing and formation of several types of aggregates of oil. This study summarized the behaviours and processes that transformed the particles of oil into small tar balls, larger logs, sheets, and large lumps into a slick. Sediment uptake or loss was found to be the major process that caused the changes in density. The behaviour of the oils was compared with respect to density and uptake of various types of sediment. The paper also reviewed the literature on dense oil behaviour. Weathering experiments performed on dense oils to determine if extensive weathering could render oils heavier than water showed that rarely is weathering the only factor in the bulk sinking of oil. Once an oil is submerged, little weathering occurs, either by dissolution or volatilization. The uptake of particulate matter is the most important process in increasing density. This study reviewed over-washing experiments to develop a mathematical solution of the conditions required for oil to be covered by a

Neutron scattering of a floating heavy water bridge

International Nuclear Information System (INIS)

Fuchs, Elmar C; Bitschnau, Brigitte; Woisetschlaeger, Jakob; Maier, Eugen; Beuneu, Brigitte; Teixeira, Jose

2009-01-01

When high voltage is applied to distilled water filled into two beakers close to each other, a water connection forms spontaneously, giving the impression of a floating water bridge (Fuchs et al 2007 J. Phys. D: Appl. Phys. 40 6112-4, 2008 J. Phys. D: Appl. Phys. 41 185502). This phenomenon is of special interest, since it comprises a number of phenomena currently tackled in modern water science. In this work, the first data on neutron scattering of a floating heavy water bridge are presented and possible interpretations are discussed. D 2 O was measured instead of H 2 O because of the very strong incoherent scattering of H. The obtained data support the 'bubble hypothesis' suggested earlier (Fuchs et al 2008).

Removal of Heavy Metals from Drinking Water by Magnetic Carbon Nanostructures Prepared from Biomass

Directory of Open Access Journals (Sweden)

Muhammad Muneeb Ur Rahman Khattak

2017-01-01

Full Text Available Heavy metals contamination of drinking water has significant adverse effects on human health due to their toxic nature. In this study a new adsorbent, magnetic graphitic nanostructures were prepared from watermelon waste. The adsorbent was characterized by different instrumental techniques (surface area analyzer, FTIR, XRD, EDX, SEM, and TG/DTA and was used for the removal of heavy metals (As, Cr, Cu, Pb, and Zn from water. The adsorption parameters were determined for heavy metals adsorption using Freundlich and Langmuir isotherms. The adsorption kinetics and effect of time, pH, and temperature on heavy metal ions were also determined. The best fits were obtained for Freundlich isotherm. The percent adsorption showed a decline at high pH. Best fit was obtained with second-order kinetics model for the kinetics experiments. The values of ΔH° and ΔG° were negative while that of ΔS° was positive. The prepared adsorbent has high adsorption capacities and can be efficiently used for the removal of heavy metals from water.

Studies of the Effect of Heavy Water in the Fast Reactor FR0

Energy Technology Data Exchange (ETDEWEB)

Tiren, L I; Haakansson, R; Karmhag, B

1968-08-15

Core 9 of the FR0 fast critical assembly was diluted with heavy water to 24 vol. per cent, contained in thin walled copper cans. The report describes measurements of the critical mass and the reactivity coefficient of heavy water in this core. The effect of the heterogeneous core composition on these items is also dealt with. The results are compared with theoretical predictions using several computer codes. Criticality is accurately predicted, but the measured reactivity coefficient of heavy water is about 20 % lower than the value obtained with the best available methods, involving the SPENG and DTF-4 programmes. The result of bunching measurements, in which the degree of heterogeneity of core composition was changed, is compared with theoretical estimates of the resonance shielding, flux advantage and leakage components of the heterogeneity effect.

Studies of the Effect of Heavy Water in the Fast Reactor FR0

International Nuclear Information System (INIS)

Tiren, L.I.; Haakansson, R.; Karmhag, B.

1968-08-01

Core 9 of the FR0 fast critical assembly was diluted with heavy water to 24 vol. per cent, contained in thin walled copper cans. The report describes measurements of the critical mass and the reactivity coefficient of heavy water in this core. The effect of the heterogeneous core composition on these items is also dealt with. The results are compared with theoretical predictions using several computer codes. Criticality is accurately predicted, but the measured reactivity coefficient of heavy water is about 20 % lower than the value obtained with the best available methods, involving the SPENG and DTF-4 programmes. The result of bunching measurements, in which the degree of heterogeneity of core composition was changed, is compared with theoretical estimates of the resonance shielding, flux advantage and leakage components of the heterogeneity effect

Chemical elimination of alumina in suspension in nuclear reactors heavy water

International Nuclear Information System (INIS)

Ledoux, A.

1967-02-01

Corrosion of aluminium in contact with moderating water in nuclear reactor leads to the formation of an alumina hydrosol which can have an adverse effect on the operation of the reactor. Several physical methods have been used in an attempt to counteract this effect. The method proposed here consists in the elimination of the aluminium by dissolution and subsequent fixation in the ionic form on mixed-bed ion-exchange resin. In order to do this, the parameters and the values of these parameters most favorable to the dissolution process have been determined. If the moderator is heavy water, the deuterated acid can be prepared by converting a solution in heavy water to a salt of the acid using a deuterated cationic resin. (author) [fr

ANALISIS PERBANDINGAN OUTPUT DAYA LISTRIK PANEL SURYA SISTEM TRACKING DENGAN SOLAR REFLECTOR

Directory of Open Access Journals (Sweden)

I B Kd Surya Negara

2016-03-01

Full Text Available Indonesia merupakan negara beriklim tropis yang memiliki intensitas radiasi matahari yang sangat besar dan intensitas radiasi tersebut berpotensi untuk dikembangkan menjadi Pembangkit Listrik Tenaga Surya. Efisiensi dari panel surya saat ini masih perlu pertimbangan lebih lanjut. Efisiensi panel surya yang rendah ini, berpengaruh pada hasil output daya listrik yang dihasilkan. Upaya untuk meningkatkan output daya listrik panel surya, yaitu dengan sistem tracking dan solar reflector. Penelitian ini bertujuan untuk mengetahui output daya listrik yang lebih maksimal. Metode dalam penelitian ini menggunakan sistem tracking yang pergerakannya berdasarkan waktu dan menggunakan solar reflector dengan cermin datar dan sudut reflector yang berbeda. Hasil dari perbandingan sistem tracking dengan solar reflector yaitu solar reflector menghasilkan output daya listrik lebih besar dibandingan dengan sistem tracking, dimana solar reflector menghasilkan output daya listrik sebesar 0.1224 Watt dan sistem tracking sebesar 0.1136 Watt.

Enhancing the stepped solar still performance using internal and external reflectors

International Nuclear Information System (INIS)

Omara, Z.M.; Kabeel, A.E.; Younes, M.M.

2014-01-01

Highlights: • Stepped solar still with internal and external reflectors have been investigated. • The productivity of the modified stepped solar still is higher than conventional by 103%. • The productivity of stepped still with external mirror is higher than that for conventional still by 88%. - Abstract: The performance of stepped solar still with internal and external reflectors have been investigated in the current study. The reflectors are used to enhance energy input to the stepped still. The influence of internal and external (top and bottom) reflectors on the performance of the stepped solar still is investigated. A comparison between modified stepped solar still and conventional solar still is carried out to evaluate the developed desalination system performance under the same climate conditions. The results indicated that, during experimentation the productivity of the modified stepped solar still with internal and external (top and bottom) reflectors is higher than that for conventional still approximately by 125%. In this case the estimated cost of 1 l of distillate for stepped still with reflectors and conventional solar stills is approximately 0.031$ and 0.049$, respectively

Embalse nuclear power plant and heavy water valuation

International Nuclear Information System (INIS)

Martin, Daniel E.

2008-01-01

The author describes the nuclear power plant characteristics, the building work, the heavy water valuation criteria and the reasons why he considers that any capital good can be valued by the cash-flow method. The Embalse nuclear power plant replacement value is of U$S 1.593.538.000. (author) [es

Highly accurate photogrammetric measurements of the Planck reflectors

Science.gov (United States)

Amiri Parian, Jafar; Gruen, Armin; Cozzani, Alessandro

2017-11-01

The Planck mission of the European Space Agency (ESA) is designed to image the anisotropies of the Cosmic Background Radiation Field over the whole sky. To achieve this aim, sophisticated reflectors are used as part of the Planck telescope receiving system. The system consists of secondary and primary reflectors which are sections of two different ellipsoids of revolution with mean diameters of 1 and 1.6 meters. Deformations of the reflectors which influence the optical parameters and the gain of receiving signals are investigated in vacuum and at very low temperatures. For this investigation, among the various high accuracy measurement techniques, photogrammetry was selected. With respect to the photogrammetric measurements, special considerations had to be taken into account in design steps, measurement arrangement and data processing to achieve very high accuracies. The determinability of additional parameters of the camera under the given network configuration, datum definition, reliability and precision issues as well as workspace limits and propagating errors from different sources are considered. We have designed an optimal photogrammetric network by heuristic simulation for the flight model of the primary and the secondary reflectors with relative precisions better than 1:1000'000 and 1:400'000 to achieve the requested accuracies. A least squares best fit ellipsoid method was developed to determine the optical parameters of the reflectors. In this paper we will report about the procedures, the network design and the results of real measurements.

Energy conservation measures adopted at Heavy Water Plant, Manuguru

International Nuclear Information System (INIS)

Gupta, R.V.; Venugopal, M.

1997-01-01

The importance of conservation of energy is well recognised all over the world as the world reserves of fossil fuels will eventually run out depending on the rate of their use. This paper deals with various energy conservation schemes adopted at Heavy Water Plant, Manuguru (HWPM). Most energy conservation measures offer large financial saving with very short pay back periods. This fact has been well recognised by the management of HWPM as well as Heavy Water Board and their wholehearted and enthusiastic approach to energy conservation and energy management yielded very good results in reducing the operating cost. The process of energy conservation is not a one time exercise. Persistent efforts are on to identify the areas like condition of heat exchangers, margins in control valves, steam and condensate leakages etc. for further reduction in energy consumption

Beyond Wires and Seeds: Reflector-guided Breast Lesion Localization and Excision.

Science.gov (United States)

Mango, Victoria L; Wynn, Ralph T; Feldman, Sheldon; Friedlander, Lauren; Desperito, Elise; Patel, Sejal N; Gomberawalla, Ameer; Ha, Richard

2017-08-01

Purpose To evaluate outcomes of Savi Scout (Cianna Medical, Aliso Viejo, Calif) reflector-guided localization and excision of breast lesions by analyzing reflector placement, localization, and removal, along with target excision and rates of repeat excision (referred to as re-excision). Materials and Methods A single-institution retrospective review of 100 women who underwent breast lesion localization and excision by using the Savi Scout surgical guidance system from June 2015 to May 2016 was performed. By using image guidance 0-8 days before surgery, 123 nonradioactive, infrared-activated, electromagnetic wave reflectors were percutaneously inserted adjacent to or within 111 breast targets. Twenty patients had two or three reflectors placed for bracketing or for localizing multiple lesions, and when ipsilateral, they were placed as close as 2.6 cm apart. Target and reflector were localized intraoperatively by one of two breast surgeons who used a handpiece that emitted infrared light and electromagnetic waves. Radiographs of the specimen and pathologic analysis helped verify target and reflector removal. Target to reflector distance was measured on the mammogram and radiograph of the specimen, and reflector depth was measured on the mammogram. Pathologic analysis was reviewed. Re-excision rates and complications were recorded. By using statistics software, descriptive statistics were generated with 95% confidence intervals (CIs) calculated. Results By using sonographic (40 of 123; 32.5%; 95% CI: 24.9%, 41.2%) or mammographic (83 of 123; 67.5%; 95% CI: 58.8% 75.1%) guidance, 123 (100%; 95% CI: 96.4%, 100%) reflectors were placed. Mean mammographic target to reflector distance was 0.3 cm. All 123 (100%; 95% CI: 96.4%, 100%) targets and reflectors were excised. Pathologic analysis yielded 54 of 110 malignancies (49.1%; 95% CI: 39.9%, 58.3%; average, 1.0 cm; range, 0.1-5 cm), 32 high-risk lesions (29.1%; 95% CI: 21.4%, 38.2%), and 24 benign lesions (21.8%; 95% CI

Water chemistry management of research reactor in JAERI

Energy Technology Data Exchange (ETDEWEB)

Yoshijima, Tetsuo [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1998-10-01

The JRR-3M cooling system consists of four systems, namely; (1) primary cooling system, (2) heavy water cooling system, (3) helium system and (4) secondary cooling system. The heavy water is used for reflector and pressurized with helium gas. Water chemistry management of the JRR-3M cooling systems is one of the important subject for the safety operation. The main objects are to prevent the corrosion of cooling system and fuel elements, to suppress the plant radiation build-up and to minimize the generation of radioactive waste. All measured values were within the limits of specifications and JRR-3M reactor was operated with safety in 1996. Spent fuels of JRR-3M reactor are stored in the spent fuel pool. This pool water has been analyzed to prevent corrosion of aluminum cladding of spent fuels. Water chemistry of spent fuel pool water is applied to the prevention of corrosion of aluminum alloys including fuel cladding. The JRR-2 reactor was eternally stopped in December 1996 and is now under decommissioning. The JRR-2 reactor is composed of heavy water tank, fuel guide tube and horizontal experimental hole. These are constructed of aluminum alloy and biological shield and upper shield are constructed of concrete. Three types of corrosion of aluminum alloy were observed in the JRR-2. The Alkaline corrosion of aluminum tube occurred in 1972 because of the mechanical damage of the aluminum fuel guide tube which is used for fuel handling. Modification of the reactor top shield was started in 1974 and completed in 1975. (author)

Nonimaging reflectors for efficient uniform illumination.

Science.gov (United States)

Gordon, J M; Kashin, P; Rabl, A

1992-10-01

Nonimaging reflectors that are an extension of the design principle that was developed for compound parabolic concentrator type devices are proposed for illumination applications. The optical designs presented offer maximal lighting efficiency while they retain sharp angular control of the radiation and highly uniform flux densities on distant target planes. Our results are presented for symmetrical configurations in two dimensions (troughlike reflectors) for flat and for tubular sources. For fields of view of practical interest (half-angle in the 30-60 degrees range), these devices can achieve minimum-tomaximum intensity ratios of 0.7, while they remain compact and incur low reflective losses.

A painless approach to use distributed digital-control system for Heavy Water Plant- Tuticorin

International Nuclear Information System (INIS)

Potti, V.S.; Krishnan, S.; Rao, V.C.; Lamba, D.S.

1994-01-01

Heavy Water Plant (Tuticorin) production is based on mono thermal process of ammonia-hydrogen exchange and is connected with a 1100 tons per day capacity ammonia plant of M/s Southern Petrochemical Industries Limited for getting its feed. The deuterium concentration in the syngas (N 2 + 3H 2 ) is extracted through ammonia-hydrogen exchange process and finally burnt with air in the final product unit to get heavy water. The depleted syngas is sent back to M/s SPIC's synthesis unit. The purpose of this paper is to highlight the instrumentation requirements of heavy water production, problems encountered in use of DDCS along with remedial action taken for the back up facility. (author)

D2O, Computation of Thermodynamic and Transport Properties of Heavy Water

International Nuclear Information System (INIS)

Durmayaz, Ahmet

2000-01-01

1 - Description of program or function: A computer program for the fast computation of the thermodynamic and transport properties of heavy water (D 2 O) at saturation, in subcooled liquid and superheated vapor states. Specific volume (or density), specific enthalpy, specific entropy, constant-pressure specific heat and temperature at saturation are calculated by a number of piecewise continuous approximation functions of (and their derivatives are calculated with respect to) pressure whereas pressure at saturation is calculated by a piecewise continuous approximation function of temperature for heavy water. Density in subcooled liquid state, specific volume in super-heated vapor state, specific enthalpy, specific entropy and constant-pressure specific heat in both of these states are calculated by some piecewise continuous approximation functions of pressure and temperature for heavy water. The correlations used in the calculation of these thermodynamic properties of heavy water were derived by fitting some appropriate curves to the data given in the steam tables by Hill et al (1981). The whole set of correlations and the approximation method used in their derivation are presented by Durmayaz (1997). Dynamic viscosity and thermal conductivity for heavy water are calculated as functions of temperature and density with the correlations given by Hill et al (1981), by Matsunaga and Nagashima (1983) and by Kestin et al (1984). Surface tension for heavy water is calculated as a function of temperature with the correlation given by Crabtree and Siman-Tov (1993). 2 - Methods: A group of pressure-enthalpy (P-h) pairs can be given in an input data file or assigned in the main program without knowing the state in which fluid takes place. In this case, first, the enthalpies at saturation corresponding to the given pressure are computed. Second, the state is determined by comparing the given enthalpy to the saturation enthalpies. Then, the properties are computed. Program D 2 O

Device and method to enrich and process heavy water

International Nuclear Information System (INIS)

Hammerli, M.M.; Butler, J.P.

1979-01-01

A device to process and enrich heavy water is proposed which is based on a combined electrolysis catalyst exchange system in which a D 2 O enrichment of more than 99.8% is achieved in the end stage. Water partly enriched with D 2 -containing hydrogen gas from an electrolysis cell is brought into contact in a catalyst column. The water is further enriched here with deuterium. It is then fed to the electrolysis cell. Details of the apparatus are closely described. (UWI) [de

Waste minimization through process optimization/integration and resource management at eco-friendly Heavy Water Plants

International Nuclear Information System (INIS)

Nageshri, Jagdish; Gupta, S.K.

2004-01-01

Heavy Water Board has celebrated 2003 as Environmental Conservation Year captivating a range of enviro-friendly measures. This article attempts to give a brief overview of the outcome of systems and adapted procedures for waste minimization through process integration and resource management at Heavy Water Plants

Advances in heavy water reactors

International Nuclear Information System (INIS)

1994-03-01

The current IAEA programme in advanced nuclear power technology promotes technical information exchange between Member States with major development programmes. The Technical Committee Meeting (TCM) on Advances in Heavy Water Reactors was organized by the IAEA in the framework of the activities of the International Working Group on Advanced Technologies for Water Cooled Reactors (IWGATWR) and hosted by the Atomic Energy of Canada Limited. Sixty-five participants from nine countries (Canada, Czech Republic, India, German, Japan, Republic of Korea, Pakistan, Romania and USA) and the IAEA attended the TCM. Thirty-four papers were presented and discussed in five sessions. A separate abstract was prepared for each of these papers. All recommendations which were addressed by the participants of the Technical Committee meeting to the IWGATWR have been submitted to the 5th IWGATWR meeting in September 1993. They were reviewed and used as input for the preparation of the IAEA programme in the area of advanced water cooled reactors. This TCM was mainly oriented towards advances in HWRs and on projects which are now in the design process and under discussion. Refs, figs and tabs

Poultry litter-based activated carbon for removing heavy metal ions in water.

Science.gov (United States)

Guo, Mingxin; Qiu, Guannan; Song, Weiping

2010-02-01

Utilization of poultry litter as a precursor material to manufacture activated carbon for treating heavy metal-contaminated water is a value-added strategy for recycling the organic waste. Batch adsorption experiments were conducted to investigate kinetics, isotherms, and capacity of poultry litter-based activated carbon for removing heavy metal ions in water. It was revealed that poultry litter-based activated carbon possessed significantly higher adsorption affinity and capacity for heavy metals than commercial activated carbons derived from bituminous coal and coconut shell. Adsorption of metal ions onto poultry litter-based carbon was rapid and followed Sigmoidal Chapman patterns as a function of contact time. Adsorption isotherms could be described by different models such as Langmuir and Freundlich equations, depending on the metal species and the coexistence of other metal ions. Potentially 404 mmol of Cu2+, 945 mmol of Pb2+, 236 mmol of Zn2+, and 250-300 mmol of Cd2+ would be adsorbed per kg of poultry litter-derived activated carbon. Releases of nutrients and metal ions from litter-derived carbon did not pose secondary water contamination risks. The study suggests that poultry litter can be utilized as a precursor material for economically manufacturing granular activated carbon that is to be used in wastewater treatment for removing heavy metals.

Impact of different moderator ratios with light and heavy water cooled reactors in equilibrium states

International Nuclear Information System (INIS)

Permana, Sidik; Takaki, Naoyuki; Sekimoto, Hiroshi

2006-01-01

As an issue of sustainable development in the world, energy sustainability using nuclear energy may be possible using several different ways such as increasing breeding capability of the reactors and optimizing the fuel utilization using spent fuel after reprocessing as well as exploring additional nuclear resources from sea water. In this present study the characteristics of light and heavy water cooled reactors for different moderator ratios in equilibrium states have been investigated. The moderator to fuel ratio (MFR) is varied from 0.1 to 4.0. Four fuel cycle schemes are evaluated in order to investigate the effect of heavy metal (HM) recycling. A calculation method for determining the required uranium enrichment for criticality of the systems has been developed by coupling the equilibrium fuel cycle burn-up calculation and cell calculation of SRAC 2000 code using nuclear data library from the JENDL 3.2. The results show a thermal spectrum peak appears for light water coolant and no thermal peak for heavy water coolant along the MFR (0.1 ≤ MFR ≤ 4.0). The plutonium quality can be reduced effectively by increasing the MFR and number of recycled HM. Considering the effect of increasing number of recycled HM; it is also effective to reduce the uranium utilization and to increase the conversion ratio. trans-Plutonium production such as americium (Am) and curium (Cm) productions are smaller for heavy water coolant than light water coolant. The light water coolant shows the feasibility of breeding when HM is recycled with reducing the MFR. Wider feasible area of breeding has been obtained when light water coolant is replaced by heavy water coolant

Enhanced light absorption of silicon solar cells with dielectric nanostructured back reflector

Science.gov (United States)

Ren, Rui; Zhong, Zheng

2018-06-01

This paper investigates the light absorption property of nanostructured dielectric reflectors in silicon thin film solar cells using numerical simulation. Flat thin film solar cell with ZnO nanostructured back reflector can produce comparable photocurrent to the control model with Ag nanostructured back reflector. Furthermore, when it is integrated with nano-pillar surface decoration, a photocurrent density of 29.5 mA/cm2 can be achieved, demonstrating a photocurrent enhancement of 5% as compared to the model with Ag nanostructured back reflector.

Heavy metal contamination of water and fish in peri-urban dams ...

African Journals Online (AJOL)

Heavy metals were measured in water, sediment and fish in dams located downstream of effluent discharge zones in Bulawayo and were compared to those in a pristine upstream dam. Water conductivity indicated pollution of downstream dams. Levels of lead (0.13 – 0.28 ppm) and cadmium (0.02 – 0.06 ppm) in water from ...

Heavy water production benefits of a supporting r and d program

International Nuclear Information System (INIS)

Bancroft, A.R.; Chuang, K.T.; Dalrymple, D.G.

1981-01-01

Considerable economic benefit was obtained from an active R and D program while the Canadian heavy water plants were brought to mature operation during the 1970s. The introduction to Canada of this new chemical processing industry led to unexpected process, equipment and materials problems. Having a small team of technical experts already working on heavy water processes and a much larger R and D team working in related fields allowed a rapid response to the problems that limited production. The number of engineers and scientists working on the GS process rose rapidly from a skeleton team in 1970 to 54 during 1974. Effort declined steadily as the major problems were solved and reached 22 by 1980. Cumulative effort over the decade was 264 man-years at a cost of 3.3 percent of the value of the heavy water produced. The new production benefits have lagged behind the R and D expenditure by a few years and the current spending rate is 1.2 percent of product value. Important contributions were made in the areas of process simulation, process chemistry, materials of construction, sieve trays, and mechanical equipment

Heavy metal pollution in drinking water - a global risk for the human ...

African Journals Online (AJOL)

Fabian Fernandez

parts of the world heavy metal (HM) concentrations in drinking water are higher than some international guideline values. ..... become the basis for several drinking water treatment approaches ...... physiological and hygienic needs. Monitoring ...

Structural-electromagnetic bidirectional coupling analysis of space large film reflector antennas

Science.gov (United States)

Zhang, Xinghua; Zhang, Shuxin; Cheng, ZhengAi; Duan, Baoyan; Yang, Chen; Li, Meng; Hou, Xinbin; Li, Xun

2017-10-01

As used for energy transmission, a space large film reflector antenna (SLFRA) is characterized by large size and enduring high power density. The structural flexibility and the microwave radiation pressure (MRP) will lead to the phenomenon of structural-electromagnetic bidirectional coupling (SEBC). In this paper, the SEBC model of SLFRA is presented, then the deformation induced by the MRP and the corresponding far field pattern deterioration are simulated. Results show that, the direction of the MRP is identical to the normal of the reflector surface, and the magnitude is proportional to the power density and the square of cosine incident angle. For a typical cosine function distributed electric field, the MRP is a square of cosine distributed across the diameter. The maximum deflections of SLFRA linearly increase with the increasing microwave power densities and the square of the reflector diameters, and vary inversely with the film thicknesses. When the reflector diameter becomes 100 m large and the microwave power density exceeds 102 W/cm2, the gain loss of the 6.3 μm-thick reflector goes beyond 0.75 dB. When the MRP-induced deflection degrades the reflector performance, the SEBC should be taken into account.

Various analytical techniques used for the measurement of isotopic purity of heavy water at Madras Atomic Power Station

International Nuclear Information System (INIS)

Satyanarayanan, V.; Umapathy, P.; Bhaskaran, R.; Nagarajan, J.; Pradeep, Jeena; Ayyar, S.R.

2008-01-01

The paper deals with the various techniques used for the measurement of isotopic purity of heavy water samples received from different sources viz. reactor systems, heavy water upgrading plant and fresh consignment from heavy water production plants. Heavy water is used in PHWRs as moderator and primary coolant. Isotopic Purity is an important parameter to be monitored/analysed regularly for both the systems. There is a minimum isotopic purity level to be maintained in the moderator system due to neutron economy/fuel burnup and in the case of coolant system the measurement is of paramount importance due to its safety considerations. The selection of the method of analysis depends on the isotopic range. The techniques used to measure the isotopic purity of heavy water are a) Infrared Spectrophotometry b) Refractometry c) Densitometry. Infrared spectrometer uses the property of molecular absorption of IR radiation by HOD species and the absorbance is the measure of isotopic purity. This technique is generally used for measuring high isotopic (80-99.98%) and low isotopic samples. Refractometer uses the property of refractive index of heavy water. The difference in refractive indices of light water and heavy water is 0.0048. A 1 % change in D 2 O concentration would thus equal to 0.000048 refractive index units. This method is used for determining the approximate isotopic value of a sample. Density meter uses the property of difference in densities of light and heavy water. The difference in density of 99.999% D 2 O and light water is 0.107540 which covers the whole range of interest. The experience gained with these techniques in the measurements of isotopic purity of various samples are presented in this paper. (author)

Water Quality and Heavy Metal Concentrations in Sediment of Sungai Kelantan, Kelantan, Malaysia: A Baseline Study

International Nuclear Information System (INIS)

Ahmad, A.K.; Mushrifah, I.; Mohamad Shuhaimi Othman

2009-01-01

A study on water quality and heavy metal concentration in sediment at selected sites of Sungai Kelantan was carried out. Ten water samples were collected along the river for physical and chemical analysis and twenty-six water and sediment samples were collected for heavy metal analysis. Water was sampled at three different dates throughout the study period whereas sediments were collected once. In addition to heavy metal analysis, sediment samples were also analysed for texture, ph and organic content. The physical and chemical water quality analyses were carried out according to the ALPHA procedures. Result of water quality analysis (physico-chemical) indicated that Sungai Kelantan is characterised by excellent water quality and comparable to pristine ecosystems such as the National Park and Kenyir Lake. This river was classified into class I - class III based on Malaysian interim water quality standard criteria (INWQS). Heavy metals Pb, Zn, Cu and Cd was detected at low concentration in sediment samples, except for Fe and Mn. The presence of Fe and Mn in sediment samples was though to be of natural origin from the soil. Anthropogenic metal concentrations in sediment were low indicating that Sungai Kelantan has not experienced extreme pollution. (author)

A painless approach to use distributed digital-control system for Heavy Water Plant- Tuticorin

Energy Technology Data Exchange (ETDEWEB)

Potti, V S; Krishnan, S; Rao, V C; Lamba, D S [Heavy Water Project, Tuticorin (India)

1994-06-01

Heavy Water Plant (Tuticorin) production is based on mono thermal process of ammonia-hydrogen exchange and is connected with a 1100 tons per day capacity ammonia plant of M/s Southern Petrochemical Industries Limited for getting its feed. The deuterium concentration in the syngas (N{sub 2} + 3H{sub 2}) is extracted through ammonia-hydrogen exchange process and finally burnt with air in the final product unit to get heavy water. The depleted syngas is sent back to M/s SPIC`s synthesis unit. The purpose of this paper is to highlight the instrumentation requirements of heavy water production, problems encountered in use of DDCS along with remedial action taken for the back up facility. (author). 3 refs., 2 figs.

Process development, design and operation of off-line purification system for oil-contaminated impure heavy water

International Nuclear Information System (INIS)

Bose, H.; Rakesh Kumar; Gandhi, H.C.; Unny, V.K.P.; Ghosh, S.K.; Mishra, Vivek; Shukla, D.K.; Duraisamy, S.; Agarwal, S.K.

2004-01-01

A large volume of degraded, tritiated heavy water contaminated with mineral oil and ionic impurities have accumulated at Dhruva in the past years of reactor operation as a result of routine operation and maintenance activities. The need was felt for a simple and efficient process that could be set up and operated locally at site using readily available materials, to purify the accumulated impure heavy waters at Dhruva so as to make them acceptable at the up gradation facilities. After a detailed laboratory study, a three stage clean-up process was developed which could purify a highly turbid oil-water emulsion to yield clear, oil-free and de-mineralized heavy water at reasonable rates of volume through-put. Based on the laboratory data, a suitably scaled up purification unit has been designed and commissioned which in the past few months has processed a sizeable volume of oil-contaminated heavy water waste from Dhruva, with most satisfactory results

Investigations for heavy metals pollution in the Nile water in Khartoum area using XRF

International Nuclear Information System (INIS)

Salih, Saadia Elsir

1998-06-01

The purpose of this study was to perform measurements for heavy metals pollution in the Nile water in Khartoum area. Ten locations were selected for the study on the white Nile, the Blue Nile and the Nile. Standard methods were used for samples collection and preparation for the measurements using XRF. Nine elements were observed and their concentrations determined in the various locations. These Ti, Cr, Fe, Cu, Zn, As, Pb, Zr, and Se. From the performed measurements for heavy metals pollution in the Nile water in Khartoum area using the XRF method the following conclusions can be made: There is no heavy metal pollution in the Nile water in Khartoum area resulting from industrial activities. However, there are indications for possible Pb pollution resulting from automobile emission. - The concentrations for the observed heavy metals, except Fe, were much below the maximum permissible international levels provided by the USA, EEC and WHO. - The origin for the observed concentrations of heavy metals, except for Pb, was considered to be soil and silt carried by river in it's journey from the Ethiopian Highlands and lake Victoria. (Author)

A study of pollution extent in some drinking water resources by heavy elements in Hadramout governorate

International Nuclear Information System (INIS)

Barheyan, Saad Awadh

2001-01-01

The paper is considered as a preliminary study of pollution extent in some drinking water resources in Hadramout governorate by heavy elements which differ in their toxicity. The elements subjected to study are Cd, Pb, Fe, Cr, Mn, Zn, Co and Cu. Atomic absorption spectrometric method of analysis (AAS) is used for the determination of heavy elements concentrations. The elemental analysis of drinking water samples shows that the concentration of the above-mentioned elements in drinking water resources, lies in the permissible limit given by the WHO. Similarity of elements content is observed in Thela and Fuwah waters, bu the case is different for Ghail Bawzeer and Asshihir waters due to their different lithospheric structures. Drinking water used by the civilians is not subjected to physical, biological or chemical treatment which may lead to total or partial removal of heavy elements and other rejected impurities. Drinking water running in distribution nets is a hard water and has a weak base (Ph which explains the reason why heavy elements are absorbed and precipitated inside drinking water pipes before they reach consumers. This type of hard water causes accumulation of salt precipitates inside the water pipes which results in many economic and health disturbances to consumers. The slight increase of Cr, Mn, and Co concentration in drinking water flowing in the pipes may be due to the effect of some anions such as nitrates which form soluble compounds with the elements contained in the chemical composition of the drinking water pipes. This paper is a strong indicator for determination of heavy elements concentrations in different drinking water resources in Hadramout govemorate. Such approach seeks a further comprehensive work with special focus on the study of lithospheric structure of the feeding water regions of Hadramout aquifers. (author)

Reflector and Protections in a Sodium-cooled Fast Reactor: Modelling and Optimization

Science.gov (United States)

Blanchet, David; Fontaine, Bruno

2017-09-01

The ASTRID project (Advanced Sodium Technological Reactor for Industrial Demonstration) is a Generation IV nuclear reactor concept under development in France [1]. In this frame, studies are underway to optimize radial reflectors and protections. Considering radial protections made in natural boron carbide, this study is conducted to assess the neutronic performances of the MgO as the reference choice for reflector material, in comparison with other possible materials including a more conventional stainless steel. The analysis is based upon a simplified 1-D and 2-D deterministic modelling of the reactor, providing simplified interfaces between core, reflector and protections. Such models allow examining detailed reaction rate distributions; they also provide physical insights into local spectral effects occurring at the Core-Reflector and at the Reflector-Protection interfaces.

Safety and environmental aspects of heavy water production (Paper No. 4.1)

International Nuclear Information System (INIS)

Singh, Mohinder

1992-01-01

Different processes are utilised for heavy water production in the heavy water plants in India. H 2 S is used in large quantities as carrier gas to extract deuterium content from water. The safe handling of such large quantities of H 2 S gas poses a major problem because of its toxicity, high corrosive nature and high flammability. Handling of large quantities of synthesis gas in ammonia based plants at high pressure and temperature poses a major problem because it is a mixture of hydrogen and nitrogen. H 2 is highly inflammable and explosive when mixed with air or oxygen. All the safety aspects considered while designing, fabricating, constructing and operating the plants are described. (author). 5 tabs

Bioaccumulation of heavy metals in organs of fresh water fish Cyprinus carpio (Common carp)

International Nuclear Information System (INIS)

Vinodhini, R.; Narayanan, M.

2008-01-01

The objective of the present study is to determine the bioaccumulation of heavy metals in various organs of the fresh water fish exposed to heavy metal contaminated water system. The experimental fish was exposed to Cr. Ni, Cd and Pb at sublethal concentrations for periods of 32 days. The elements Cd, Pb, Ni and Cr were assayed using Shimadzu AA 6200 atomic absorption spectrophotometry and the results were given as μg/g dry wt. The accumulation of heavy metal gradually increases in liver during the heavy metal exposure period. All the results were statistically significant at p Pb > Ni > Cr and Pb > Cd > Ni > Cr. Similarly, in case of kidney and flesh tissues, the order was Pb > Cd > Cr > Ni and Pb > Cr > Cd > Ni. In all heavy metals, the bioaccumulation of lead and cadmium proportion was significantly increased in the tissues of Cyprinus carpio (Common carp)

Measurement of M{sup 3} and k{sub {infinity}} for heavy water natural uranium assembly

Energy Technology Data Exchange (ETDEWEB)

Popovic, D; Raisic, N; Markovic, H; Takac, S; Zdravkovic, Z; Lolic, B [Boris Kidric Institute of Nuclear Sciences, Vinca, Beograd (Yugoslavia)

1959-03-15

The migration length M and the infinite multiplication factor k{sub {infinity}} of the heavy water-natural uranium bare assembly are determined by measuring the reactivity of the reactor as function of the heavy water level. Since the assembly is non reflected the results obtained are of relatively high accuracy. (author)

Heavy water. An original project in the Argentine Patagonia

International Nuclear Information System (INIS)

Conde Bidabehere, Luis F.

2000-01-01

The history of the heavy water production plant built in Arroyito, in the Argentine province of Neuquen is related. Details are given on the development of the project and on the operation of the plant. The possible complementary production of ammonia and fertilizers is analyzed

Instrumentation and signal processing for the detection of heavy water using off axis-integrated cavity output spectroscopy technique

Science.gov (United States)

Gupta, A.; Singh, P. J.; Gaikwad, D. Y.; Udupa, D. V.; Topkar, A.; Sahoo, N. K.

2018-02-01

An experimental setup is developed for the trace level detection of heavy water (HDO) using the off axis-integrated cavity output spectroscopy technique. The absorption spectrum of water samples is recorded in the spectral range of 7190.7 cm-1-7191.5 cm-1 with the diode laser as the light source. From the recorded water vapor absorption spectrum, the heavy water concentration is determined from the HDO and water line. The effect of cavity gain nonlinearity with per pass absorption is studied. The signal processing and data fitting procedure is devised to obtain linear calibration curves by including nonlinear cavity gain effects into the calculation. Initial calibration of mirror reflectivity is performed by measurements on the natural water sample. The signal processing and data fitting method has been validated by the measurement of the HDO concentration in water samples over a wide range from 20 ppm to 2280 ppm showing a linear calibration curve. The average measurement time is about 30 s. The experimental technique presented in this paper could be applied for the development of a portable instrument for the fast measurement of water isotopic composition in heavy water plants and for the detection of heavy water leak in pressurized heavy water reactors.

Standards for deuterium analysis requirements of heavy water plants (Preprint No. CA-1)

Energy Technology Data Exchange (ETDEWEB)

Rathi, B N; Gopalakrishnan, V T; Alphonse, K P; Pawar, P L; Sadhukhan, H K [Bhabha Atomic Research Centre, Bombay (India). Heavy Water Div.

1989-04-01

Accurate analysis of deuterium, covering the entire range, is of great importance in production of heavy water. Most of the methods for determination of deuterium in gas or liquid samples require appropriate standards. Since density of pure protium oxide and pure deuterium oxide has been determined very accurately by a large number of workers and density of mixtures of H{sub 2}O and D{sub 2}O follows a linear relation, it is possible to use accurate density determination for measurement of deuterium content. Float method for density measurements was improved further and used for the preparation of primary heavy water standards in high and low deuterium ranges. Heavy water plant laboratories require gas standards (ammonia synthesis gas matrix), in addition to low deuterium water standards, for calibration of mass spectrometers. SLAP (Standard Light Antarctic Precipitation, D/D+H = 89.02+-0.05ppm) and SMOW (Standard Mean Ocean Water, D/D+H =155.76+-0.05ppm) available from IAEA, Vienna, along with water practically free from deuterium, were used as standards to prepare secondary liquid standards. These secondary standards were subsequently reduced and mixed with pure nitrogen to obtain D/D+H standards in syngas matrix. (author). 8 refs., 2 figs.

Safety analysis of RA reactor operation, I-II, Part I - RA reactor technical and operation characteristics; Analiza sigurnosti rada reaktora RA - I-III, I deo - Tehnicke i pogonske karakteristike reaktora RA

Energy Technology Data Exchange (ETDEWEB)

Raisic, N [Institute of Nuclear Sciences Boris Kidric, Vinca, Beograd (Serbia and Montenegro)

1963-02-15

RA research reactor is a thermal, heavy water moderated system with graphite reflector having nominal power 6.5 MW. The 2% enriched metal uranium fuel in the reactor core produces mean thermal neutron flux of 2.9 10{sup 13} neutrons/cm{sup 2} s, and maximum neutron flux 5.5 10{sup 13} neutrons/cm{sup 2} s. main components of the reactor described in this report are: rector core, reflector, biological shield, heavy water cooling system, ordinary water cooling system, helium system, reactor control system, reactor safety system, dosimetry system, power supply system, and fuel transport system. Detailed reactor properties and engineering drawings of all the system are part of this volume.

Determination of heavy metals and genotoxicity of water from an ...

African Journals Online (AJOL)

Determination of heavy metals and genotoxicity of water from an artesian well ... do Amaral, Vanessa Marques de Oliveira Moraes, Luciana Pereira Silva ... environmental interest because it is the most important zinc producer district of Brazil.

Ellipsoidal reflector for measuring oto-acoustic emissions

DEFF Research Database (Denmark)

Epp, Bastian; Pulkki, Ville; Heiskanen, Vesa

2014-01-01

A truncated prolate ellipsoidal reflector having the ear canal of a listener at one focal point and large- diaphragm low-noise microphone at the other focal point is proposed for free-field recordings of oto-acoustic emissions. A prototype reflector consisting of three pieces is presented, which...... enables measuring the response of the system with different truncations. The response of the system is measured with a miniature loud- speaker, and proof-of-concept measurements of oto-acoustic emissions are presented. The effect of truncation and other physical parameters to the performance of the system...

Monitoring of heavy metals in selected Water Supply Systems in Poland, in relation to current regulations

Science.gov (United States)

Szuster-Janiaczyk, Agnieszka; Zeuschner, Piotr; Noga, Paweł; Skrzypczak, Marta

2018-02-01

The study presents an analysis of water quality monitoring in terms of the content of heavy metals, which is conducted in three independent water supply systems in Poland. The analysis showed that the monitoring of heavy metals isn't reliable - both the quantity of tested water samples and the location of the monitoring points are the problem. The analysis of changes in water quality from raw water to tap water was possible only for one of the analysed systems and indicate a gradual deterioration of water quality, although still within acceptable limits of legal regulations.

Selective heavy metals removal from waters by amorphous zirconium phosphate: behavior and mechanism.

Science.gov (United States)

Pan, Bingcai; Zhang, Qingrui; Du, Wei; Zhang, Weiming; Pan, Bingjun; Zhang, Qingjian; Xu, Zhengwen; Zhang, Quanxing

2007-07-01

Selective removal of heavy metals from water has been of considerable concern for several decades. In the present study, the amorphous zirconium phosphate (ZrP) was synthesized and characterized by X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), scanning electron micrography (SEM), thermogravimetric analysis (TGA) as well as pH-titration experiments. Uptake of heavy metals including lead, cadmium, and zinc onto ZrP was studied by using a polystyrene sulfonic-acid exchanger D-001 as a reference sorbent and Ca(2+) as a competing cation due to its ubiquity in natural or industrial waters. The results indicated that the uptake of heavy metals onto ZrP is essentially an ion-exchange process and dependent upon solution pH. In comparison with D-001, ZrP exhibited more favorable sorption of heavy metals particularly in terms of high selectivity, as indicated by the distribution coefficients of ZrP even several orders higher than D-001 towards heavy metals when calcium ion coexisted at a high level in solution. The Fourier transform-infrared (FT-IR) spectroscopic investigation indicated that the uptake of calcium, cadmium, and zinc ions onto ZrP is only driven by the electrostatic interaction, while that of lead ion is possibly dependent upon the inner-sphere complex formation with ZrP. XPS results further elucidated that ZrP displays different sorption affinity towards heavy metals in the same order as selectivity sequence of Pb(2+)>Zn(2+) approximately Cd(2+)>Ca(2+), which can be explained by hard and soft acids and bases (HASB) theory. Moreover, uptake of heavy metals onto ZrP approached to equilibrium quickly and the used ZrP could be readily regenerated for reuse by the dilute HCl solution. Thus, all the results suggest that amorphous ZrP has excellent potential as a sorption material for water treatment.

Combined electrolysis and catalytic exchange (CECE) technology - an economical alternative for heavy water upgraders using water distillation

International Nuclear Information System (INIS)

Ryland, D.K.; Sadhankar, R.R.

2003-01-01

Heavy water upgrading is a unique and crucial part of a CANDU power station. Water distillation (DW) systems are used for heavy water upgrading in all CANDU stations. The DW upgrader is designed to take advantage of the difference in relative volatility (a measure of separation of isotopes) between H 2 O and D 2 O. However, the low relative volatility of the H 2 O/D 2 O system requires large number of stages (long columns) and large reflux ratios (large reboiler loads) - thus resulting in significant capital and operating costs. Atomic Energy of Canada Limited (AECL) developed the Combined Electrolysis and Catalytic Exchange (CECE) technology as an economical alternative to the DW system. CECE-based upgraders have been demonstrated in pilot scale facilities at AECL Chalk River Laboratories and in Hamilton, Ontario. This design is based on catalytic hydrogen isotope exchange between water and hydrogen gas. (author)

Consequence of potential accidents in heavy water plants

International Nuclear Information System (INIS)

Croitoru, C.; Lazar, R.E.; Preda, I.A.; Dumitrescu, M.

1998-01-01

Heavy water plants realize the primary isotopic concentrations of water using H 2 O-H 2 S chemical exchange and they are chemical plants. As these plants are handling and spreading large quantities of hydrogen sulphide (high toxic, corrosive, flammable and explosive as) maintained in the process at relative high temperatures and pressures, it is required an assessing of risks associated with the potential accidents. The H 2 S released in atmosphere as a result of an accident will have negative consequences to property, population and environment. This paper presents a model of consequences quantitative assessment and its outcome for the most dangerous accident in heavy water plants. Several states of the art risk based methods were modified and linked together to form a proper model for this analyse. Five basic steps to identify the risks involved in operating the plants are followed: hazard identification, accident sequence development, H 2 S emissions calculus, dispersion analyses and consequences determination. A brief description of each step and some information of analysis results are provided. The accident proportions, the atmospheric conditions and the population density in the respective area were accounted for consequences calculus. The specific results of the consequences analysis allow to develop the plant's operating safety requirements so that the risk remain at an acceptable level. (authors)

Distribution of analytes over TXRF reflectors

International Nuclear Information System (INIS)

Bernasconi, G.; Tajani, A.

2000-01-01

One of the most frequently used methods for trace element analysis in TXRF involves the evaporation of small amounts of aqueous solutions over flat reflectors. This method has the advantage of in-situ pre-concentration of the analytes, which together with the low background due to the total reflection in the substrate leads to excellent detection limits and high signal to noise ratio. The spiking of the liquid sample with an internal standard provides also a simple way to achieve multielemental quantitative analysis. However the elements are not homogeneously distributed over the reflector after the liquid phase has been evaporated. This distribution may be different for the unknown elements and the internal standards and may influence the accuracy of the quantitative results. In this presentation we used μ-XRF techniques to map this distribution. Small (20 μl) drops of a binary solution were evaporated over silicon reflectors and then mapped using a focused X-ray beam with about 100 μm resolution. A typical ring structure showing some differences in the distribution of both elements has been observed. One of the reflectors was also measured in a TXRF setup turning it at different angles with reference to the X-ray beam (with constant incidence and take-off angles) and variations of the intensity relation between both elements were measured. This work shows the influence of the sample distribution and proposes methods to evaluate it. In order to assess the limitations of the accuracy of the results due to the sample distribution more measurements would be necessary, however due to the small size of typical TXRF samples and the tight geometry of TXRF setups the influence of the sample distribution is not large. (author)

A real-time tritium-in-water monitor for measurement of heavy water leak to the secondary coolant

International Nuclear Information System (INIS)

Rathnakaran, M.; Ravetkar, R.M.; Samant, R.K.; Abani, M.C.

2000-01-01

The paper describes the development and evaluation of on-line, real-time tritium in water monitor for detection and measurement of heavy water leak to the secondary coolant in a Pressurised Heavy Water Reactor. The detector used for this is a plastic scintillator film, made in the form of sponge and housed in a flow cell which is used for measurement of tritium activity present in heavy water. Two photomultiplier tubes are optically coupled on either face of the flow cell detector and measurement is done in coincidence mode. The sample water is continuously passed through the flow cell detector and a continuous measurement of tritium activity is carried out. It is observed that the impurities in the process water sample are gradually trapped in the flow cell, which affects the transparency of the detector with use. This reduces the sensitivity of the system. In addition, chlorine, which is added in the sample water, to arrest the fungus formation, creates chemiluminescence which interfere the measurement. To improve the sample quality as well as to eliminate the chemiluminescence created by chlorine, sample conditioner consisting of polypropylene candle, activated charcoal and glass fibre filter paper is developed. Polypropylene candle traps particulates above 5 μm pore size, activated charcoal absorbs organic compounds, free chlorine, fungus and turbidity and glass fibre filter paper stops submicron size particles. The measurement is also affected by the interference of dissolved argon-41 in the sample water. A bubbler system developed at BARC is used to strip the dissolved Ar-41 present in the sample which enables the system to measure tritium in presence of this interfering radioactive gas. The microprocessor based electronic system, used in the monitor provides the facility for selection of counting time and thereby improving the counting statistics. Alarm circuit is provided to give timely alarm when the tritium activity concentration exceeds the preset level

Characterization of a Bifacial Photovoltaic Panel Integrated with External Diffuse and Semimirror Type Reflectors

Directory of Open Access Journals (Sweden)

P. Ooshaksaraei

2013-01-01

Full Text Available Silicon wafer accounts for almost one-half the cost of a photovoltaic (PV panel. A bifacial silicon solar cell is attractive due to its potential of enhancing power generation from the same silicon wafer in comparison with a conventional monofacial solar cell. The bifacial PV cell is able to capture solar radiation by back surface. This ability requires a suitable reflector appropriately oriented and separated from the cell’s rear surface. In order to optimize the bifacial solar cell performance with respect to an external back surface reflector, diffuse and semimirror reflectors were investigated at various angles and separations from the back surface. A simple bifacial solar panel, consisting of four monocrystalline Si solar cells, was designed and built. Reflection from the rear surface was provided by an extended semimirror and a white-painted diffuse reflector. Maximum power generation was observed at 30° with respect to ground for the semimirror reflector and 10° for diffuse reflector at an optimized reflector-panel separation of 115 mm. Output power enhancement of 20% and 15% from semimirror and diffuse reflectors, respectively, were observed. This loss from diffuse reflector is attributed to scattering of light beyond the rear surface capture cross-section of the bifacial solar panel.

Assessment of natural radioactivity and heavy metals in water and soil around seismically active area

International Nuclear Information System (INIS)

Oktay Baykara; Mahmut Dogru; Firat University, Elazig

2010-01-01

The natural radioactivity concentration and some heavy metals in various water and soil samples collected from seismically active area have been determined. Gross-alpha and beta concentrations of different 33 water samples and some heavy metal (Fe, Pb, Cu, K, Mn, Cr and Zn) concentration in 72 soil samples collected from two major fault systems (North and East Anatolian Active Fault Systems) in Turkey have been studied. This survey regarding gross-alpha and beta radioactivity and some heavy metals concentrations was carried out by means of Krieger method using a gross-alpha and beta-counting system and atomic absorption spectrometry (AAS), respectively. Also, gross annual effective dose from the average gross-alpha activity in waters were calculated. (author)

Problems connected with the production of heavy water in France; Problemes relatifs a la production d'eau lourde en France

Energy Technology Data Exchange (ETDEWEB)

Roth, E [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1956-07-01

The decision to study the nuclear energy in France in 1945 has seen the construction of the first natural uranium reactor for research purpose only, Zoe reactor. The utilization of heavy water as moderator was motivated by permitting the economical utilization of natural uranium oxides as fuel and a good handling. The five tons of heavy water required by the Zoe reactor were initially obtained from Norway production. With nuclear development and the construction of the first power reactors for electricity production, the demand in heavy water increased. The heavy water production by French industry became of a great interest. The first production started in the southwest of France using a fertilizers production plant and the electrolytic process used in Norway. The electrolytic process of hydrogen was quickly limited by the limited number of large fertilizers plants in France. Thus, in 1953, French nuclear research concentrated on the distillation of liquid hydrogen and water distillation for the heavy water production. The liquid hydrogen distillation presents a better yield in heavy water extraction than the electrolytic process but it was still depending from large fertilizers production plants. Although the water distillation process is simple, the high purity required for nuclear uses induced a high cost. The advantages and disadvantages of these two processes are discussed as well as others heavy water production processes using concentration process of already enriched water and the prospect of the use of the natural gas from the Lacq deposit. Economical aspect and cost production for each of heavy water production processes will be also discussed. (M.P.)

Technologies for tritium control in fission reactors moderated with heavy water

International Nuclear Information System (INIS)

Ramilo, L.B.; Gomez de Soler, S.M.

1996-01-01

This study was done within a program one of whose objectives was to analyze the possible strategies and technologies, to be applied to HWR at Argentine nuclear power plants, for tritium control. The high contribution of tritium to the total dose has given rise to the need by the operators and/or designers to carry out developments and improvements to try to optimize tritium control technologies. Within a tritium control program, only that one which includes the heavy water detritiation will allow to reduce the tritium concentrations at optimum levels for safety and cost-effective power plant operation. The technology chosen to be applied should depend not only on the technical feasibility but also on the analysis of economic and juncture factors such as, among others, the quantity of heavy water to be treated. It is the authors' belief that AECL tendency concerning heavy water treatment in its future reactors would be to employ the CECE technology complemented with immobilization on titanium beds, with the 'on-line' detritiation in each nuclear power plant. This would not be of immediate application since our analysis suggests that AECL would assume that the process is under development and needs to be tested. (author). 21 refs

Manufacturing opportunities in the Canadian CANDU and heavy water programs

International Nuclear Information System (INIS)

Reny, J.P.

The volume of business available to Canadian manufacturers of CANDU power plant and heavy water plant components is analyzed over about the next 10 years. Implications of exported nuclear technology and plants are explored. (E.C.B.)

Low energy neutrons from a sup 2 sup 3 sup 9 PuBe isotopic neutron source inserting in moderating media

CERN Document Server

Vega, H R

2002-01-01

Several neutron applications share a common problem: the neutron source design. In this work MCNP computer code has been used to design a moderated sup 2 sup 3 sup 9 PuBe neutron source to produce low energy neutrons. The design involves the source located at the center of a spherical moderator. Moderator media studied were light water, heavy water and a heterogeneous combination of light water and heavy water. Similar moderating features were found between the 24.5 cm-radius container filled with heavy water (23.0-cm-thick) and that made with light water (3.5-cm-thick) plus heavy water (19.5-cm-thick). A sup 2 sup 3 sup 9 PuBe neutron source inserted in this moderator produces, at 27 cm, a neutron fluence of 1.8 x 10 sup - sup 4 n-cm sup - sup 2 per source neutron, with an average neutron energy of 0.34 MeV, where 47.8 % have an energy <= 0.4 eV. A further study of this moderator was carried out using a reflector medium made of graphite. Thus, 15-cm-thickness reflector improves the neutron field producing...

The Planck Telescope reflectors

Science.gov (United States)

Stute, Thomas

2004-09-01

The mechanical division of EADS-Astrium GmbH, Friedrichshafen is currently engaged with the development, manufacturing and testing of the advanced dimensionally stable composite reflectors for the ESA satellite borne telescope Planck. The objective of the ESA mission Planck is to analyse the first light that filled the universe, the cosmic microwave background radiation. Under contract of the Danish Space Research Institute and ESA EADS-Astrium GmbH is developing the all CFRP primary and secondary reflectors for the 1.5-metre telescope which is the main instrument of the Planck satellite. The operational frequency ranges from to 25 GHz to 1000 GHz. The demanding high contour accuracy and surface roughness requirements are met. The design provides the extreme dimensional stability required by the cryogenic operational environment at around 40 K. The elliptical off-axis reflectors display a classical lightweight sandwich design with CFRP core and facesheets. Isostatic mounts provide the interfaces to the telescope structure. Protected VDA provides the reflecting surface. The manufacturing is performed at the Friedrichshafen premises of EADS-Space Transportation GmbH, the former Dornier composite workshops. Advanced manufacturing technologies like true angle lay-up by CNC fibre placement and filament winding are utilized. The protected coating is applied at the CAHA facilities at the Calar Alto Observatory, Spain. The exhaustive environmental testing is performed at the facilities of IABG, Munich (mechanical testing) and for the cryo-optical tests at CSL Liege. The project is in advanced state with both Qualification Models being under environmental testing. The flight models will be delivered in 2004. The paper gives an overview over the requirements and the main structural features how these requirements are met. Special production aspects and available test results are reported.

Effect of phototherapy with alumunium foil reflectors on neonatal hyperbilirubinemia

Directory of Open Access Journals (Sweden)

Tony Ijong Dachlan

2015-03-01

Full Text Available Background Neonatal hyperbilirubinemia (NH is one of the most common problems in neonates, but it can be treated with blue light phototherapy. Developing countries with limited medical equipment and funds have difficulty providing effective phototherapy to treat NH, leading to increased risk of bilirubin encephalopathy. Phototherapy with white reflecting curtains can decrease the duration of phototherapy needed to reduce bilirubin levels. Objective To compare the duration of phototherapy needed in neonates with NH who underwent phototherapy with and without aluminum foil reflectors. Methods This open clinical trial was conducted from July to August 2013 at Dr. Hasan Sadikin Hospital, Bandung, Indonesia. The inclusion criteria were term neonates with uncomplicated NH presenting in their first week of life. Subjects were randomized into two groups, those who received phototherapy with or without aluminum foil reflectors. Serum bilirubin is taken at 12th, 24th, 48th hours, then every 24 hours if needed until phototherapy can be stopped according to American Academy of Pediatrics guidelines. The outcome measured was the duration of phototherapy using survival analysis. The difference between the two groups was tested by Gehan method. Results Seventy newborns who fulfilled the inclusion criteria and had similar characteristics were randomized into two groups. The duration of phototherapy needed was significantly less in the group with aluminum foil reflectors than in the group without reflectors [72 vs. 96 hours, respectively, (P<0.01]. Conclusion The required duration of phototherapy with aluminum foil reflectors is significantly less than that of phototherapy without reflectors, in neonates with NH.

National symposium on commissioning and operating experiences in heavy water plants and associated chemical industries [Preprint volume

International Nuclear Information System (INIS)

1992-02-01

A symposium on commissioning and operating experiences in heavy water plants and associated chemical industries (SCOPEX-92) was organised to share the experience and exchange the ideas among plant operators, designers, consultants and vendors in the areas of operation, commissioning and equipment performance. This pre-print volume has been brought out as an integrated source of information on commissioning and operation of heavy water plants. The following aspects of heavy water plants are covered: commissioning and operation, instrumentation and control, and safety and environment. (V.R.)

Heavy water GS process R and D achievements

International Nuclear Information System (INIS)

Bancroft, A.R.

1978-10-01

R and D support of Canadian heavy water production plants during the past five years has involved mainly AECL and Ontario Hydro, and their contractors. Testing has been done in the production plants, in two pilot plants and in research laboratories on topics that include sieve tray design, in-plant behaviour of oil and sulfur and choice of antifoam agent to control excessive foaming. The benefits are increased production through higher plant flows and higher extraction of deuterium from the feed, less down time because of process problems and lower cost for materials used to control water chemistry. (author)

Modeling Adsorption Kinetics (Bio-remediation of Heavy Metal Contaminated Water)

Science.gov (United States)

McCarthy, Chris

My talk will focus on modeling the kinetics of the adsorption and filtering process using differential equations, stochastic methods, and recursive functions. The models have been developed in support of our interdisciplinary lab group which is conducting research into bio-remediation of heavy metal contaminated water via filtration through biomass such as spent tea leaves. The spent tea leaves are available in large quantities as a result of the industrial production of tea beverages. The heavy metals bond with the surfaces of the tea leaves (adsorption). Funding: CUNY Collaborative Incentive Research Grant.

Numerical Study of Concentration Characteristics of Linear Fresnel Reflector System

International Nuclear Information System (INIS)

Lee, Hyun Jin; Kim, Jong Kyu; Lee, Sang Nam

2015-01-01

In this study, we numerically investigated the concentration characteristics of a linear Fresnel reflector system that can drive a solar thermal absorption refrigeration system to be installed in Saudi Arabia. Using an optical modeling program based on the Monte Carlo ray-tracing method, we simulated the concentrated solar flux, concentration efficiency, and concentrated solar energy on four representative days of the year - the vernal equinox, summer solstice, autumnal equinox, and winter solstice. Except the winter solstice, the concentrations were approximately steady from 9 AM to 15 PM, and the concentration efficiencies exceed 70%. Moreover, the maximum solar flux around the solar receiver center changes only within the range of 13.0 - 14.6 kW/m 2 . When we investigated the effects of the receiver installation height, reflector width, and reflector gap, the optimal receiver installation height was found to be 5 m. A smaller reflector width had a greater concentration efficiency. However, the design of the reflector width should be based on the capacity of the refrigeration system because it dominantly affects the concentrated solar energy. The present study was an essential prerequisite for thermal analyses of the solar receiver. Thus, an optical-thermal integration study in the future will assist with the performance prediction and design of the entire system

Numerical Study of Concentration Characteristics of Linear Fresnel Reflector System

Energy Technology Data Exchange (ETDEWEB)

Lee, Hyun Jin [Kookmin Univ., Seoul (Korea, Republic of); Kim, Jong Kyu; Lee, Sang Nam [Korea Institute of Energy Research, Daejeon (Korea, Republic of)

2015-12-15

In this study, we numerically investigated the concentration characteristics of a linear Fresnel reflector system that can drive a solar thermal absorption refrigeration system to be installed in Saudi Arabia. Using an optical modeling program based on the Monte Carlo ray-tracing method, we simulated the concentrated solar flux, concentration efficiency, and concentrated solar energy on four representative days of the year - the vernal equinox, summer solstice, autumnal equinox, and winter solstice. Except the winter solstice, the concentrations were approximately steady from 9 AM to 15 PM, and the concentration efficiencies exceed 70%. Moreover, the maximum solar flux around the solar receiver center changes only within the range of 13.0 - 14.6 kW/m{sup 2}. When we investigated the effects of the receiver installation height, reflector width, and reflector gap, the optimal receiver installation height was found to be 5 m. A smaller reflector width had a greater concentration efficiency. However, the design of the reflector width should be based on the capacity of the refrigeration system because it dominantly affects the concentrated solar energy. The present study was an essential prerequisite for thermal analyses of the solar receiver. Thus, an optical-thermal integration study in the future will assist with the performance prediction and design of the entire system.

Modeling the transport of hydrogen in the primary coolant of pressurized heavy water reactors

International Nuclear Information System (INIS)

Subramanian, H.; Velmurugan, S.; Narasimhan, S.V.; Jain, A.K.; Dash, S.C.

2008-01-01

Heavy water (D 2 O) is used in primary heat transport systems of PHWRs. To suppress the radiolysis of heavy water and to control oxygen, hydrogen is added at regular intervals to the primary heat transport system. The added hydrogen finds it way to the heavy water storage tank after passing through the bleed condenser. Owing to the different temperatures and two phase region present in these systems, hydrogen gets redistributed. It is important to know the concentration of dissolved hydrogen in these regions in order to ensure a steady state dissolved hydrogen concentration in the primary system. Different power stations report variations in the frequency and quantity of hydrogen added to achieve the prescribed steady state level. This paper makes an attempt to account for the inventory of hydrogen and model its transport in PHT system. (author)

Bioaccumulation of heavy metals in water, sediment and fish ...

African Journals Online (AJOL)

Dr. Hnay

2012-09-25

Sep 25, 2012 ... these pollutants is the chemical substances that stay longer and become toxic in water columns. Within them, heavy metals have positive effects on the vital activities of several organisms and impairment in food chain by affecting biological activities of the living organisms in ecosystem (Gundogu and Erden ...

Tweens demulsification effects on heavy crude oil/water emulsion

Directory of Open Access Journals (Sweden)

Nastaran Hayati Roodbari

2016-09-01

Full Text Available The demulsification role of Tweens (nonionic polymers was determined in the separation of water from heavy crude oil emulsion. According to the previous researches, these nonionic polymers, having hydrophilic and lipophilic groups, are appropriate for making oil in water emulsion. In this research their effects in certain concentrations on demulsifying of water in crude oil emulsion were proved. High molecular weight, alkenes’ chains and groups of ketone and ester in these polymers can improve their performance for the demulsification of water in crude oil emulsion. Their efficiencies are improved with electronegative groups such as oxygen. They leave no corrosion effect because they are neutral and do not leave counter ions.

Effects of sulfate on heavy metal release from iron corrosion scales in drinking water distribution system.

Science.gov (United States)

Sun, Huifang; Shi, Baoyou; Yang, Fan; Wang, Dongsheng

2017-05-01

Trace heavy metals accumulated in iron corrosion scales within a drinking water distribution system (DWDS) could potentially be released to bulk water and consequently deteriorate the tap water quality. The objective of this study was to identify and evaluate the release of trace heavy metals in DWDS under changing source water conditions. Experimental pipe loops with different iron corrosion scales were set up to simulate the actual DWDS. The effects of sulfate levels on heavy metal release were systemically investigated. Heavy metal releases of Mn, Ni, Cu, Pb, Cr and As could be rapidly triggered by sulfate addition but the releases slowly decreased over time. Heavy metal release was more severe in pipes transporting groundwater (GW) than in pipes transporting surface water (SW). There were strong positive correlations (R 2  > 0.8) between the releases of Fe and Mn, Fe and Ni, Fe and Cu, and Fe and Pb. When switching to higher sulfate water, iron corrosion scales in all pipe loops tended to be more stable (especially in pipes transporting GW), with a larger proportion of stable constituents (mainly Fe 3 O 4 ) and fewer unstable compounds (β-FeOOH, γ-FeOOH, FeCO 3 and amorphous iron oxides). The main functional iron reducing bacteria (IRB) communities were favorable for the formation of Fe 3 O 4 . The transformation of corrosion scales and the growth of sulfate reducing bacteria (SRB) accounted for the gradually reduced heavy metal release with time. The higher metal release in pipes transporting GW could be due to increased Fe 6 (OH) 12 CO 3 content under higher sulfate concentrations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Heavy water handbook. Evaluation of available thermophysical properties of heavy water (D2O) liquid and vapour

International Nuclear Information System (INIS)

Bukovsky, J.; Haack, K.; Wiig, P.

1993-01-01

Numerous publications on the thermophysical data of heavy water (D 2 O) have been published since D 2 O became commercially available in the 1930's. Some of these data are in mutual disagreement. This has led to confusion among the scientifical and technical staffs who needed the information on the D 2 O thermophysical data. Correct thermophysical data must be consistent, i.e. their mutual relations must be in accordance to the fundamental thermophysical laws. The work behind this publication has been focussed at collecting all avalilable D 2 O data and checking the data mutually by means of these fundamental thermophysical criteria. Depending on the various production methods, the oxygen content of the D 2 O is enriched more or less in the heavier oxygen isotopes 17 O and 18 O. This, together with the amount of impurities and dissolved gases in the D 2 O samples of the various references, might - to some extent - explain the discrepancies between the data sources. Only a few references contain information on these subjects. The D 2 O data sets which were found to be the most reliable are presented in chapter 9, in tables as well as in diagrams, together with the corresponding H 2 O data for comparison. The diagrams are commented for reliability where it was found necessary. Furthermore, the publication contains short descriptions on the heavy water sources, availability, production processes, economy, material and energy demands for production. A comprehensive list of references is enclosed. (author)

Main-Reflector Manufacturing Technology for the Deep Space Optical Communications Ground Station

Science.gov (United States)

Britcliffe, M. J.; Hoppe, D. J.

2001-01-01

The Deep Space Network (DSN) has plans to develop a 10-m-diameter optical communications receiving station. The system uses the direct detection technique, which has much different requirements from a typical astronomical telescope. The receiver must operate in daylight and nighttime conditions. This imposes special requirements on the optical system to reject stray light from the Sun and other sources. One of the biggest challenges is designing a main-reflector surface that meets these requirements and can be produced at a reasonable cost. The requirements for the performance of the reflector are presented. To date, an aspherical primary reflector has been assumed. A reflector with a spherical reflector has a major cost advantage over an aspherical design, with no sacrifice in performance. A survey of current manufacturing techniques for optical mirrors of this type was performed. Techniques including solid glass, lightweight glass, diamond-turned aluminum, and composite mirrors were investigated.

Study of heavy metal concentration (As, Ba, Cd, Hg, Pb, Crin water resources and river of Borujerd city in 2008-2009

Directory of Open Access Journals (Sweden)

bahram kamarehei

2010-02-01

Full Text Available with industrial and economic growth and different material production that humans gained from natural resources for their comfort and walfare, inwardly introduced toxic material and heavy metal entered environment that there created serious problems for themselves and environment. This study accomplished to determine heavy metal concentration (As, Ba, Cd, Hg, Pb, Crin water resources and river of Borujerd city in 2008-2009. Materials and Methods: This descriptive cross-sectional study was conducted to determine heavy metal concentration (As, Ba, Cd, Hg, Pb, Cr in water resources and river of Borujerd city. 54 samples of water were taken from 18 drinking water wells, and also in two times 8 samples of Borujerd river were taken from before and after the city. Then samples carried into the lab and were concentrated ten times using expressed methods and standard methods. Then heavy metal concentration determined by AAP (WFX 130 and results analyzed by SPSS and EXCEL software. Results: Heavy metal concentration average (As, Ba, Cd, Hg, Pb, Cr in drinking water wells were 0. 0, 0. 3222, 0. 0014, 0. 0002, 0. 0077 mg/l respectively. and heavy metal concentration in river water after the city has been increased than before the city. Conclusion: Results indicated that heavy metal concentration average in Borujerd drinking water wells were lower than standard amounts and drinking water wells didn’t pollute with heavy metal. But heavy metal concentration in river water after the city has been increased than the before of it because city waste water enters the city river.

New evaluation of thermal neutron scattering libraries for light and heavy water

Directory of Open Access Journals (Sweden)

Marquez Damian Jose Ignacio

2017-01-01

Full Text Available In order to improve the design and safety of thermal nuclear reactors and for verification of criticality safety conditions on systems with significant amount of fissile materials and water, it is necessary to perform high-precision neutron transport calculations and estimate uncertainties of the results. These calculations are based on neutron interaction data distributed in evaluated nuclear data libraries. To improve the evaluations of thermal scattering sub-libraries, we developed a set of thermal neutron scattering cross sections (scattering kernels for hydrogen bound in light water, and deuterium and oxygen bound in heavy water, in the ENDF-6 format from room temperature up to the critical temperatures of molecular liquids. The new evaluations were generated and processable with NJOY99 and also with NJOY-2012 with minor modifications (updates, and with the new version of NJOY-2016. The new TSL libraries are based on molecular dynamics simulations with GROMACS and recent experimental data, and result in an improvement of the calculation of single neutron scattering quantities. In this work, we discuss the importance of taking into account self-diffusion in liquids to accurately describe the neutron scattering at low neutron energies (quasi-elastic peak problem. To improve modeling of heavy water, it is important to take into account temperature-dependent static structure factors and apply Sköld approximation to the coherent inelastic components of the scattering matrix. The usage of the new set of scattering matrices and cross-sections improves the calculation of thermal critical systems moderated and/or reflected with light/heavy water obtained from the International Criticality Safety Benchmark Evaluation Project (ICSBEP handbook. For example, the use of the new thermal scattering library for heavy water, combined with the ROSFOND-2010 evaluation of the cross sections for deuterium, results in an improvement of the C/E ratio in 48 out of

New evaluation of thermal neutron scattering libraries for light and heavy water

Science.gov (United States)

Marquez Damian, Jose Ignacio; Granada, Jose Rolando; Cantargi, Florencia; Roubtsov, Danila

2017-09-01

In order to improve the design and safety of thermal nuclear reactors and for verification of criticality safety conditions on systems with significant amount of fissile materials and water, it is necessary to perform high-precision neutron transport calculations and estimate uncertainties of the results. These calculations are based on neutron interaction data distributed in evaluated nuclear data libraries. To improve the evaluations of thermal scattering sub-libraries, we developed a set of thermal neutron scattering cross sections (scattering kernels) for hydrogen bound in light water, and deuterium and oxygen bound in heavy water, in the ENDF-6 format from room temperature up to the critical temperatures of molecular liquids. The new evaluations were generated and processable with NJOY99 and also with NJOY-2012 with minor modifications (updates), and with the new version of NJOY-2016. The new TSL libraries are based on molecular dynamics simulations with GROMACS and recent experimental data, and result in an improvement of the calculation of single neutron scattering quantities. In this work, we discuss the importance of taking into account self-diffusion in liquids to accurately describe the neutron scattering at low neutron energies (quasi-elastic peak problem). To improve modeling of heavy water, it is important to take into account temperature-dependent static structure factors and apply Sköld approximation to the coherent inelastic components of the scattering matrix. The usage of the new set of scattering matrices and cross-sections improves the calculation of thermal critical systems moderated and/or reflected with light/heavy water obtained from the International Criticality Safety Benchmark Evaluation Project (ICSBEP) handbook. For example, the use of the new thermal scattering library for heavy water, combined with the ROSFOND-2010 evaluation of the cross sections for deuterium, results in an improvement of the C/E ratio in 48 out of 65

A figure control sensor for the Large Deployable Reflector (LDR)

Science.gov (United States)

Bartman, R.; Dubovitsky, S.

1988-01-01

A sensing and control system is required to maintain high optical figure quality in a segmented reflector. Upon detecting a deviation of the segmented surface from its ideal form, the system drives segment mounted actuators to realign the individual segments and thereby return the surface to its intended figure. When the reflector is in use, a set of figure sensors will determine positions of a number of points on the back surface of each of the reflector's segments, each sensor being assigned to a single point. By measuring the positional deviations of these points from previously established nominal values, the figure sensors provide the control system with the information required to maintain the reflector's optical figure. The optical lever, multiple wavelength interferometer, and electronic capacitive sensor, the most promising technologies for the development of the figure sensor, are illustrated. It is concluded that to select a particular implementation of the figure sensors, performance requirement will be refined and relevant technologies investigated further.

Irrigation water quality influences heavy metal uptake by willows in biosolids.