Battery Dimensioning and Life Cycle Costs Analysis for a Heavy-Duty Truck Considering the Requirements of Long-Haul Transportation

Directory of Open Access Journals (Sweden)

Ivan Mareev

2017-12-01

Full Text Available The use of heavy-duty battery electric trucks for long-haul transportation is challenging because of the required high energy amounts and thus the high capacity of traction batteries. Furthermore a high capacity battery implies high initial costs for the electric vehicle. This study investigates the required battery capacity for battery electric trucks considering the requirements of long-haul transportation in Germany and compares the life cycle costs of battery electric trucks and conventional diesel trucks in different transportation scenarios. The average consumption is simulated for different battery electric truck configurations on the main German highways and transportation scenarios incorporating battery charging during driver rest periods. The results show that in average case the required battery would restrict the payload to only 80% of a usual diesel truck payload that might be acceptable considering the statistical payload use. The life cycle costs in the examined scenarios also considering the charging infrastructure show that battery electric trucks can already perform on the same costs level as diesel trucks in certain scenarios.

Influence of methane emissions and vehicle efficiency on the climate implications of heavy-duty natural gas trucks.

Science.gov (United States)

Camuzeaux, Jonathan R; Alvarez, Ramón A; Brooks, Susanne A; Browne, Joshua B; Sterner, Thomas

2015-06-02

While natural gas produces lower carbon dioxide emissions than diesel during combustion, if enough methane is emitted across the fuel cycle, then switching a heavy-duty truck fleet from diesel to natural gas can produce net climate damages (more radiative forcing) for decades. Using the Technology Warming Potential methodology, we assess the climate implications of a diesel to natural gas switch in heavy-duty trucks. We consider spark ignition (SI) and high-pressure direct injection (HPDI) natural gas engines and compressed and liquefied natural gas. Given uncertainty surrounding several key assumptions and the potential for technology to evolve, results are evaluated for a range of inputs for well-to-pump natural gas loss rates, vehicle efficiency, and pump-to-wheels (in-use) methane emissions. Using reference case assumptions reflecting currently available data, we find that converting heavy-duty truck fleets leads to damages to the climate for several decades: around 70-90 years for the SI cases, and 50 years for the more efficient HPDI. Our range of results indicates that these fuel switches have the potential to produce climate benefits on all time frames, but combinations of significant well-to-wheels methane emissions reductions and natural gas vehicle efficiency improvements would be required.

Simulated Fuel Economy and Emissions Performance during City and Interstate Driving for a Heavy-Duty Hybrid Truck

Energy Technology Data Exchange (ETDEWEB)

Daw, C. Stuart; Gao, Zhiming; Smith, David E.; Laclair, Tim J.; Pihl, Josh A.; Edwards, K. Dean

2013-04-08

We compare simulated fuel economy and emissions for both conventional and hybrid class 8 heavy-duty diesel trucks operating over multiple urban and highway driving cycles. Both light and heavy freight loads were considered, and all simulations included full aftertreatment for NOx and particulate emissions controls. The aftertreatment components included a diesel oxidation catalyst (DOC), urea-selective catalytic NOx reduction (SCR), and a catalyzed diesel particulate filter (DPF). Our simulated hybrid powertrain was configured with a pre-transmission parallel drive, with a single electric motor between the clutch and gearbox. A conventional HD truck with equivalent diesel engine and aftertreatment was also simulated for comparison. Our results indicate that hybridization can significantly increase HD fuel economy and improve emissions control in city driving. However, there is less potential hybridization benefit for HD highway driving. A major factor behind the reduced hybridization benefit for highway driving is that there are fewer opportunities to utilize regenerative breaking. Our aftertreatment simulations indicate that opportunities for passive DPF regeneration are much greater for both hybrid and conventional trucks during highway driving due to higher sustained exhaust temperatures. When passive DPF regeneration is extensively utilized, the fuel penalty for particulate control is virtually eliminated, except for the 0.4%-0.9% fuel penalty associated with the slightly higher exhaust backpressure.

Heavy Truck Engine Program

Energy Technology Data Exchange (ETDEWEB)

Nelson, Christopher

2009-01-08

The Heavy Duty Truck Engine Program at Cummins embodied three significant development phases. All phases of work strove to demonstrate a high level of diesel engine efficiency in the face of increasingly stringent emission requirements. Concurrently, aftertreatment system development and refinement was pursued in support of these efficiency demonstrations. The program's first phase focused on the demonstration in-vehicle of a high level of heavy duty diesel engine efficiency (45% Brake Thermal Efficiency) at a typical cruise condition while achieving composite emissions results which met the 2004 U.S. EPA legislated standards. With a combination of engine combustion calibration tuning and the development and application of Urea-based SCR and particulate aftertreatment, these demonstrations were successfully performed by Q4 of 2002. The second phase of the program directed efforts towards an in-vehicle demonstration of an engine system capable of meeting 2007 U.S. EPA legislated emissions requirements while achieving 45% Brake Thermal Efficiency at cruise conditions. Through further combustion optimization, the refinement of Cummins Cooled EGR architecture, the application of a high pressure common rail fuel system and the incorporation of optimized engine parasitics, Cummins Inc. successfully demonstrated these deliverables in Q2 of 2004. The program's final phase set a stretch goal of demonstrating 50% Brake Thermal Efficiency from a heavy duty diesel engine system capable of meeting 2010 U.S. EPA legislated emissions requirements. Cummins chose to pursue this goal through further combustion development and refinement of the Cooled EGR system architecture and also applied a Rankine cycle Waste Heat Recovery technique to convert otherwise wasted thermal energy to useful power. The engine and heat recovery system was demonstrated to achieve 50% Brake Thermal Efficiency while operating at a torque peak condition in second quarter, 2006. The 50% efficient

Semivolatile organic compound emissions from heavy-duty trucks operating on diesel and bio-diesel fuel blends

Science.gov (United States)

This study measured semivolatile organic compounds (SVOCs) in particle matter (PM) emitted from three heavy-duty trucks equipped with modern after-treatment technologies. Emissions testing was conducted as described by the George et al. VOC study also presented as part of this se...

Idle emissions from heavy-duty diesel and natural gas vehicles at high altitude.

Science.gov (United States)

McCormick, R L; Graboski, M S; Alleman, T L; Yanowitz, J

2000-11-01

Idle emissions of total hydrocarbon (THC), CO, NOx, and particulate matter (PM) were measured from 24 heavy-duty diesel-fueled (12 trucks and 12 buses) and 4 heavy-duty compressed natural gas (CNG)-fueled vehicles. The volatile organic fraction (VOF) of PM and aldehyde emissions were also measured for many of the diesel vehicles. Experiments were conducted at 1609 m above sea level using a full exhaust flow dilution tunnel method identical to that used for heavy-duty engine Federal Test Procedure (FTP) testing. Diesel trucks averaged 0.170 g/min THC, 1.183 g/min CO, 1.416 g/min NOx, and 0.030 g/min PM. Diesel buses averaged 0.137 g/min THC, 1.326 g/min CO, 2.015 g/min NOx, and 0.048 g/min PM. Results are compared to idle emission factors from the MOBILE5 and PART5 inventory models. The models significantly (45-75%) overestimate emissions of THC and CO in comparison with results measured from the fleet of vehicles examined in this study. Measured NOx emissions were significantly higher (30-100%) than model predictions. For the pre-1999 (pre-consent decree) truck engines examined in this study, idle NOx emissions increased with model year with a linear fit (r2 = 0.6). PART5 nationwide fleet average emissions are within 1 order of magnitude of emissions for the group of vehicles tested in this study. Aldehyde emissions for bus idling averaged 6 mg/min. The VOF averaged 19% of total PM for buses and 49% for trucks. CNG vehicle idle emissions averaged 1.435 g/min for THC, 1.119 g/min for CO, 0.267 g/min for NOx, and 0.003 g/min for PM. The g/min PM emissions are only a small fraction of g/min PM emissions during vehicle driving. However, idle emissions of NOx, CO, and THC are significant in comparison with driving emissions.

Development of Diesel Engine Operated Forklift Truck for Explosive Gas Atmospheres

Science.gov (United States)

Vishwakarma, Rajendra Kumar; Singh, Arvind Kumar; Ahirwal, Bhagirath; Sinha, Amalendu

2018-02-01

For the present study, a prototype diesel engine operated Forklift truck of 2 t capacity is developed for explosive gas atmosphere. The parts of the Forklift truck are assessed against risk of ignition of the explosive gases, vapors or mist grouped in Gr. IIA and having ignition temperature more than 200°C. Identification of possible sources of ignition and their control or prevention is the main objective of this work. The design transformation of a standard Forklift truck into a special Forklift truck is made on prototype basis. The safety parameters of the improved Forklift truck are discussed in this paper. The specially designed Forklift truck is useful in industries where explosive atmospheres may present during normal working conditions and risk of explosion is a concern during handling or transportation of materials. This indigenous diesel engine based Forklift truck for explosive gas atmosphere classified as Zone 1 and Zone 2 area and gas group IIA is developed first time in India in association with the Industry.

Economical and environmental assessments of compressed natural gas for diesel vehicle in Thailand

Directory of Open Access Journals (Sweden)

Prateep Chouykerd

2008-08-01

Full Text Available The economic assessments for the use of compressed natural gas as fuel for several types of diesel vehicles, rarely pick up, non-fixed route truck and private truck, were studied. It is noted that two main technologies of diesel natural gas vehicle (NGV, i.e. dedicated retrofit and diesel dual fuel (DDF, were considered in this work. It was found that the dedicated retrofit needs higher investment costs than dual fuel, but can achieve higher diesel saving than dual fuel. In detail, the payback period of dual fuel non-fixed route truck was found to be identical to dual fuel private truck both in the cases of6 wheel and 10 wheel, while dedicated retrofit non-fixed route truck and private truck are also identical and have longerpay back period than dual fuel due to its higher conversion costs.This work also presents the emissions released from all types of engines especially green house gas CO2. It was found that, in the case of light duty diesel i.e. pickup truck, dedicated retrofit emitted high level of CO2 than both dual fuel and conventional diesel engines. For heavy duty i.e. non-fixed route truck and private truck vehicles, dedicated retrofit emitted a lower level of CO2 than normal diesel engine. Other pollutants from engine emission, i.e. hydrocarbon (HC,nitric oxide (NOx, carbon monoxide (CO and particulate matter, (PM were also observed. The results indicated that, inthe case of light duty diesel, dedicated retrofit engine emits higher levels of HC and CO than diesel engine; in contrast, it emits lower level of NOx and PM than diesel and dual fuel. Dual fuel emits HC and CO higher than diesel and dedicated retrofit but emits lower level of NOx and PM than diesel. Lastly, for heavy duty diesel, it was demonstrated that non-fixed route truck and private truck heavy duty dedicated retrofit have potential to reduce emissions of HC, NOx, CO and PM when compared to normal heavy duty diesel. Engine efficiencies under dual fuel and dedicated

Heavy truck rollover characterization (phase B).

Science.gov (United States)

2009-09-01

The Heavy Truck Rollover Characterization Study - Phase-B builds on the results of prior phases of research. Phases 1 and 2 (Funded by Federal Highway Administration) involved heavy truck rollover characterization for a tractor and box-trailer; and P...

Technologies for simulation improvement of NOx and PM emissions and fuel consumption of future diesel engines for heavy-duty trucks; Shorai no ogatasha diesel engine ni okeru NOx, PM, nenryo shohi no kaizen

Energy Technology Data Exchange (ETDEWEB)

Shimoda, M.; Shimokawa, K.; Uchida, N.; Tsuji, Y.; Yokotaa, H.; Hosoya, M. [Hino Motors, Ltd., Tokyo (Japan)

1999-01-01

Future diesel engines for heavy-duty trucks are required to have significantly low NO{sub x} and PM emissions and fuel consumption characteristics. In order to improve these characteristics, various technologies including high pressure fuel injection systems, combustion optimization. high boost pressure turbocharging, EGR homogeneous charge compression ignition combined with multiple injections, and aftertreatment are discussed. As each technology has a number of challenges to overcome, it will take long before engines with these technologies are commercially available. In this paper, the research activities accomplished to date are reported. (author)

Raley's LNG Truck Site Final Data Report

Energy Technology Data Exchange (ETDEWEB)

Battelle

1999-07-01

Raley's is a 120-store grocery chain with headquarters in Sacramento, California, that has been operating eight heavy-duty LNG trucks (Kenworth T800 trucks with Cummins L10-300G engines) and two LNG yard tractors (Ottawa trucks with Cummins B5.9G engines) since April 1997. This report describes the results of data collection and evaluation of the eight heavy-duty LNG trucks compared to similar heavy-duty diesel trucks operating at Raley's. The data collection and evaluation are a part of the U.S. Department of Energy (DOE)/National Renewable Energy Laboratory (NREL) Alternative Fuel Truck Evaluation Project.

Truck Thermoacoustic Generator and Chiller

Energy Technology Data Exchange (ETDEWEB)

Keolian, Robert

2011-03-31

This Final Report describes the accomplishments of the US Department of Energy (DOE) cooperative agreement project DE-FC26-04NT42113 - Truck Thermoacoustic Generator and Chiller - whose goal is to design, fabricate and test a thermoacoustic piezoelectric generator and chiller system for use on over-the-road heavy-duty-diesel trucks, driven alternatively by the waste heat of the main diesel engine exhaust or by a burner integrated into the thermoacoustic system. The thermoacoustic system would utilize engine exhaust waste heat to generate electricity and cab air conditioning, and would also function as an auxiliary power unit (APU) for idle reduction. The unit was to be tested in Volvo engine performance and endurance test cells and then integrated onto a Class 8 over-the-road heavy-duty-diesel truck for further testing on the road. The project has been a collaboration of The Pennsylvania State University Applied Research Laboratory, Los Alamos National Laboratory, Clean Power Resources Inc., and Volvo Powertrain (Mack Trucks Inc.). Cost share funding was provided by Applied Research Laboratory, and by Clean Power Resources Inc via its grant from Innovation Works - funding that was derived from the Commonwealth of Pennsylvania. Los Alamos received its funding separately through DOE Field Work Proposal 04EE09.

Waste Management's LNG Truck Fleet: Final Results

Energy Technology Data Exchange (ETDEWEB)

Chandler, K. [Battelle (US); Norton, P. [National Renewable Energy Laboratory (US); Clark, N. [West Virginia University (US)

2001-01-25

Waste Management, Inc., began operating a fleet of heavy-duty LNG refuse trucks at its Washington, Pennsylvania, facility. The objective of the project was to provide transportation professionals with quantitative, unbiased information on the cost, maintenance, operational, and emissions characteristics of LNG as one alternative to conventional diesel for heavy-duty trucking applications.

Cummins Light Truck Diesel Engine Progress Report

International Nuclear Information System (INIS)

John H. Stang

2000-01-01

The Automotive Market in the United States is moving in the direction of more Light Trucks and fewer Small Cars. The customers for these vehicles have not changed, only their purchase decisions. Cummins has studied the requirements of this emerging market. Design and development of an engine system that will meet these customer needs has started. The engine system is a difficult one, since the combined requirements of a very fuel-efficient commercial diesel, and the performance and sociability requirements of a gasoline engine are needed. Results of early testing are presented which show that the diesel is possibly a good solution

Heavy-Duty Diesel Fuel Analysis

Science.gov (United States)

EPA's heavy-duty diesel fuel analysis program sought to quantify the hydrocarbon, NOx, and PM emission effects of diesel fuel parameters (such as cetane number, aromatics content, and fuel density) on various nonroad and highway heavy-duty diesel engines.

Electric urban delivery trucks: energy use, greenhouse gas emissions, and cost-effectiveness.

Science.gov (United States)

Lee, Dong-Yeon; Thomas, Valerie M; Brown, Marilyn A

2013-07-16

We compare electric and diesel urban delivery trucks in terms of life-cycle energy consumption, greenhouse gas (GHG) emissions, and total cost of ownership (TCO). The relative benefits of electric trucks depend heavily on vehicle efficiency associated with drive cycle, diesel fuel price, travel demand, electric drive battery replacement and price, electricity generation and transmission efficiency, electric truck recharging infrastructure, and purchase price. For a drive cycle with frequent stops and low average speed such as the New York City Cycle (NYCC), electric trucks emit 42-61% less GHGs and consume 32-54% less energy than diesel trucks, depending upon vehicle efficiency cases. Over an array of possible conditions, the median TCO of electric trucks is 22% less than that of diesel trucks on the NYCC. For a drive cycle with less frequent stops and high average speed such as the City-Suburban Heavy Vehicle Cycle (CSHVC), electric trucks emit 19-43% less GHGs and consume 5-34% less energy, but cost 1% more than diesel counterparts. Considering current and projected U.S. regional electricity generation mixes, for the baseline case, the energy use and GHG emissions ratios of electric to diesel trucks range from 48 to 82% and 25 to 89%, respectively.

EFFECTS OF ENGINE SPEED AND ACCESSORY LOAD ON IDLING EMISSIONS FROM HEAVY-DUTY DIESEL TRUCK ENGINES

Science.gov (United States)

A nontrivial portion of heavy-duty vehicle emissions of nitrogen oxides (NOx) and particulate matter (PM) occurs during idling. Regulators and the environmental community are interested in curtailing truck idling emissions, but current emissions models do not characterize them ac...

On-road emission characteristics of heavy-duty diesel vehicles in Shanghai

Science.gov (United States)

Chen, Changhong; Huang, Cheng; Jing, Qiguo; Wang, Haikun; Pan, Hansheng; Li, Li; Zhao, Jing; Dai, Yi; Huang, Haiying; Schipper, Lee; Streets, David G.

On-road vehicle tests of nine heavy-duty diesel trucks were conducted using SEMTECH-D, an emissions measuring instrument provided by Sensors, Inc. The total length of roads for the tests was 186 km. Data were obtained for 37,255 effective driving cycles, including 17,216 on arterial roads, 15,444 on residential roads, and 4595 on highways. The impacts of speed and acceleration on fuel consumption and emissions were analyzed. Results show that trucks spend an average of 16.5% of the time in idling mode, 25.5% in acceleration mode, 27.9% in deceleration mode, and only 30.0% at cruise speed. The average emission factors of CO, total hydrocarbons (THC), and NO x for the selected vehicles are (4.96±2.90), (1.88±1.03) and (6.54±1.90) g km -1, respectively. The vehicle emission rates vary significantly with factors like speed and acceleration. The test results reflect the actual traffic situation and the current emission status of diesel trucks in Shanghai. The measurements show that low-speed conditions with frequent acceleration and deceleration, particularly in congestion conditions, are the main factors that aggravate vehicle emissions and cause high emissions of CO and THC. Alleviating congestion would significantly improve vehicle fuel economy and reduce CO and THC emissions.

Diesel Engine Light Truck Application

Energy Technology Data Exchange (ETDEWEB)

None

2007-12-31

The Diesel Engine Light Truck Application (DELTA) program consists of two major contracts with the Department of Energy (DOE). The first one under DE-FC05-97-OR22606, starting from 1997, was completed in 2001, and consequently, a final report was submitted to DOE in 2003. The second part of the contract was under DE-FC05-02OR22909, covering the program progress from 2002 to 2007. This report is the final report of the second part of the program under contract DE-FC05-02OR22909. During the course of this contract, the program work scope and objectives were significantly changed. From 2002 to 2004, the DELTA program continued working on light-duty engine development with the 4.0L V6 DELTA engine, following the accomplishments made from the first part of the program under DE-FC05-97-OR22606. The program work scope in 2005-2007 was changed to the Diesel Particulate Filter (DPF) soot layer characterization and substrate material assessment. This final report will cover two major technical tasks. (1) Continuation of the DELTA engine development to demonstrate production-viable diesel engine technologies and to demonstrate emissions compliance with significant fuel economy advantages, covering progress made from 2002 to 2004. (2) DPF soot layer characterization and substrate material assessment from 2005-2007.

Development of a portable remote sensing system for measurement of diesel emissions from passing diesel trucks.

Science.gov (United States)

2011-04-08

A wireless remote-sensing system has been developed for measurement of NOx and particulate matters (PM) emissions from passing diesel trucks. The NOx measurement system has a UV light source with quartz fiber optics that focused the light source into...

Demand outlook for ultra-low sulfur diesel (10PPM) in Brasil; Perspectiva da demanda de diesel 10 PPM no Brasil

Energy Technology Data Exchange (ETDEWEB)

Aragao, Amanda P.; Saide, Clara Santos Martins; Machado, Giovani V.; Cavalcanti, Marcelo C.B.; Valle, Ricardo Nascimento e Silva do [Empresa de Pesquisa Energetica (EPE), Rio de Janeiro, RJ (Brazil)

2012-07-01

The purpose of this study is to assess the forecast for the diesel 10 ppm demand in the next years, by applying a bottom-up model for heavy vehicles. The relevance of this issue is evidenced by the deadline to obey a Judicial Agreement (signed in 2008 between the Federal Public Ministry, the automotive industry and other entities) and Resolution n. 403/2008 (CONAMA), which establishes that motor suitable for the use of diesel 10 ppm (P-7 Phase) is mandatory for heavy vehicles as of 2012 and that such fuel (diesel 10 ppm) must be supplied from 2013 on. Thus, the diesel national market will face important changes, either on the supply side (refining and logistics), in order to provide diesel 10 ppm, or on the demand side, with the new trucks and buses put into circulation with different motors. Particularly, on the demand side, the potential market, mainly the diesel 10 ppm portion, will be defined by the perspective of the fleet growth, energy efficiency increase and mileage variations for trucks and buses. Under the assumptions considered by this study, the demand for diesel 10 ppm for heavy vehicles will reach 27,9 million m{sup 3} in 2020.(author)

Hennepin County`s experience with heavy-duty ethanol vehicles

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-01-01

From November 1993 to October 1996, Hennepin County, which includes Minneapolis, field-tested two heavy-duty snowplow/road maintenance trucks fueled by ethanol. The overall objective of this program was to collect data from original equipment manufacturer alternative fuel heavy-duty trucks, along with comparable data from a similarly configured diesel-powered vehicle, to establish economic, emissions, performance, and durability data for the alternative fuel technology. These ethanol trucks, along with an identical third truck equipped with a diesel engine, were operated year round to maintain the Hennepin county roads. In winter, the trucks were run in 8-hour shifts plowing and hauling snow from urban and suburban roads. For the rest of the year, the three trucks were used to repair and maintain these same roads. As a result of this project, a considerable amount of data was collected on E95 fuel use, as well as maintenance, repair, emissions, and operational characteristics. Maintenance and repair costs of the E95 trucks were considerably higher primarily due to fuel filter and fuel pump issues. From an emissions standpoint, the E95 trucks emitted less particulate matter and fewer oxides of nitrogen but more carbon monoxide and hydrocarbons. Overall, the E95 trucks operated as well as the diesel, as long as the fuel filters were changed frequently. This project was a success in that E95, a domestically produced fuel from a renewable energy source, was used in a heavy-duty truck application and performed the same rigorous tasks as the diesel counterparts. The drawbacks to E95 as a heavy-duty fuel take the form of higher operational costs, higher fuel costs, shorter range, and the lack of over-the-road infrastructure.

Simulations of Multi Combustion Modes Hydrogen Engines for Heavy Duty Trucks

Directory of Open Access Journals (Sweden)

Alberto A. Boretti

2012-01-01

Full Text Available The paper presents the numerical study of a diesel direct injection heavy duty truck engine converted to hydrogen. The engine has a power turbine connected through a clutch and a continuously variable transmission to the crankshaft. The power turbine may be disconnected and by-passed when it is inefficient or inconvenient to use. The conversion is obtained by replacing the Diesel injector with a hydrogen injector and the glow plug with a jet ignition device. The hydrogen engine operates different modes of combustion depending on the relative phasing of the main injection and the jet ignition. The engine generally operates mostly in Diesel-like mode, with the most part of the main injection following the suitable creation in cylinder conditions by jet ignition. For medium-low loads, better efficienciy is obtained with the gasoline-like mode jet igniting the premixed homogeneous mixture at top dead centre. It’s permitted at higher loads or at very low loads for the excessive peak pressure or the mixture too lean to burn rapidly. The hydrogen engine has better efficiency than Diesel outputs and fuel conversion. Thanks to the larger rate of heat release, it has the opportunity to run closer to stoichiometry and the multi mode capabilities. The critical area for this engine development is found in the design of a hydrogen injector delivering the amount of fuel needed to the large volume cylinder within a Diesel-like injection time.

77 FR 4678 - Nonconformance Penalties for On-Highway Heavy Heavy-Duty Diesel Engines

Science.gov (United States)

2012-01-31

...), optimized turbo-charging, optimized fuel injection, diesel particulate filters), plus liquid urea based...-Highway Heavy Heavy-Duty Diesel Engines AGENCY: Environmental Protection Agency (EPA). ACTION: Interim... manufacturers of heavy heavy-duty diesel engines in model years 2012 and 2013 for emissions of oxides of...

Advanced vehicle dynamics of heavy trucks with the perspective of road safety

Science.gov (United States)

Trigell, Annika Stensson; Rothhämel, Malte; Pauwelussen, Joop; Kural, Karel

2017-10-01

This paper presents state-of-the art within advanced vehicle dynamics of heavy trucks with the perspective of road safety. The most common accidents with heavy trucks involved are truck against passenger cars. Safety critical situations are for example loss of control (such as rollover and lateral stability) and a majority of these occur during speed when cornering. Other critical situations are avoidance manoeuvre and road edge recovery. The dynamic behaviour of heavy trucks have significant differences compared to passenger cars and as a consequence, successful application of vehicle dynamic functions for enhanced safety of trucks might differ from the functions in passenger cars. Here, the differences between vehicle dynamics of heavy trucks and passenger cars are clarified. Advanced vehicle dynamics solutions with the perspective of road safety of trucks are presented, beginning with the topic vehicle stability, followed by the steering system, the braking system and driver assistance systems that differ in some way from that of passenger cars as well.

Greenhouse gas emissions from heavy-duty natural gas, hybrid, and conventional diesel on-road trucks during freight transport

Science.gov (United States)

Quiros, David C.; Smith, Jeremy; Thiruvengadam, Arvind; Huai, Tao; Hu, Shaohua

2017-11-01

Heavy-duty on-road vehicles account for 70% of all freight transport and 20% of transportation-sector greenhouse gas (GHG) emissions in the United States. This study measured three prevalent GHG emissions - carbon dioxide (CO2), methane (CH4) and nitrous oxide (N2O) - from seven heavy-duty vehicles, fueled by diesel and compressed natural gas (CNG), and compliant to the MY 2007 or 2010 U.S. EPA emission standards, while operated over six routes used for freight movement in California. Total combined (tractor, trailer, and payload) weights were 68,000 ± 1000 lbs. for the seven vehicles. Using the International Panel on Climate Change (IPCC) radiative forcing values for a 100-year time horizon, N2O emissions accounted for 2.6-8.3% of total tailpipe CO2 equivalent emissions (CO2-eq) for diesel vehicles equipped with Diesel Oxidation Catalyst, Diesel Particulate Filter, and Selective Catalytic Reduction system (DOC + DPF + SCR), and CH4 emissions accounted for 1.4-5.9% of CO2-eq emissions from the CNG-powered vehicle with a three-way catalyst (TWC). N2O emissions from diesel vehicles equipped with SCR (0.17-0.30 g/mi) were an order of magnitude higher than diesel vehicles without SCR (0.013-0.023 g/mi) during highway operation. For the vehicles selected in this test program, we measured 11-22% lower CO2-eq emissions from a hybrid compared to conventional diesel vehicles during transport over lower-speed routes of the freight transport system, but 20-27% higher CO2-eq emissions during higher-speed routes. Similarly, a CNG vehicle emitted up to 15% lower CO2-eq compared to conventional diesel vehicles over more neutral-grade highway routes, but emitted up to 12% greater CO2-eq emissions over routes with higher engine loads.

Diesel Engine Technician

Science.gov (United States)

Tech Directions, 2010

2010-01-01

Diesel engine technicians maintain and repair the engines that power transportation equipment such as heavy trucks, trains, buses, and locomotives. Some technicians work mainly on farm machines, ships, compressors, and pumps. Others work mostly on construction equipment such as cranes, power shovels, bulldozers, and paving machines. This article…

Heavy vehicle propulsion system materials program: Semiannual progress report, April 1996--September 1996

Energy Technology Data Exchange (ETDEWEB)

Johnson, D.R.

1997-04-01

The purpose of the Heavy Vehicle Propulsion System Materials Program is the development of materials: ceramics, intermetallics, metal alloys, and metal and ceramic coatings, to support the dieselization of class 1-3 trucks to realize a 35% fuel-economy improvement over current gasoline-fueled trucks and to support commercialization of fuel-flexible LE-55 low-emissions, high-efficiency diesel engines for class 7-8 trucks. The Office of Transportation Technologies, Office of Heavy Vehicle Technologies (OTT OHVT) has an active program to develop the technology for advanced LE-55 diesel engines with 55% efficiency and low emissions levels of 2.0 g/bhp-h NO{sub x} and 0.05 g/bhp-h particulates. The goal is also for the LE-55 engine to run on natural gas with efficiency approaching that of diesel fuel. The LE-55 program is being completed in FY 1997 and, after approximately 10 years of effort, has largely met the program goals of 55% efficiency and low emissions. However, the commercialization of the LE-55 technology requires more durable materials than those that have been used to demonstrate the goals. Heavy Vehicle Propulsion System Materials will, in concert with the heavy duty diesel engine companies, develop the durable materials required to commercialize the LE-55 technologies. OTT OHVT also recognizes a significant opportunity for reduction in petroleum consumption by dieselization of pickup trucks, vans, and sport utility vehicles. Application of the diesel engine to class 1, 2, and 3 trucks is expected to yield a 35% increase in fuel economy per vehicle. The foremost barrier to diesel use in this market is emission control. Once an engine is made certifiable, subsequent challenges will be in cost; noise, vibration, and harshness (NVH); and performance. Separate abstracts have been submitted to the database for contributions to this report.

Performance and emissions of a heavy-duty diesel/LPG dual fuel engine

Energy Technology Data Exchange (ETDEWEB)

Schaberg, Paul [Sasol Technology, Cape Town (South Africa)

2013-06-01

This paper describes an investigation into the combustion characteristics and exhaust emissions of a heavy-duty truck engine which has been equipped with an aftermarket conversion kit to enable operation as a diesel/LPG (Liquefied Petroleum Gas) dual fuel engine. During operation diesel fuel is displaced by LPG which is vaporised and metered into the inlet manifold by means of solenoid injectors. It was found that, as the LPG fuelling rate is increased, the cylinder pressure rise rates and peak cylinder pressures increase, as do the carbon monoxide and unburned hydrocarbon emissions. At higher loads it was found that the LPG autoignites independently of the diesel fuel, resulting in very high rates of cylinder pressure rise. Particulate and nitrogen oxide emissions remain largely unchanged, and carbon dioxide emissions are reduced due to the lower carbon content of the LPG fuel. Different LPG compositions were also investigated and it was found that the LPG properties that have the most significant effect on combustion and emissions were the autoignition and volatility characteristics. (orig.)

Characterization of the chemical composition of PM2.5 emitted from on-road China III and China IV diesel trucks in Beijing, China.

Science.gov (United States)

Wu, Bobo; Shen, Xianbao; Cao, Xinyue; Yao, Zhiliang; Wu, Yunong

2016-05-01

The composition of diesel exhaust fine particulate matter (PM2.5) is of growing interest because of its impacts on health and climatic factors and its application in source apportionment and aerosol modeling. We characterized the detailed chemical composition of the PM2.5, including the organic carbon (OC), elemental carbon (EC), water-soluble ions (WSIs), and elemental contents, emitted from China III and China IV diesel trucks (nine each) based on real-world measurements in Beijing using a portable emissions measurement system (PEMS). Carbonaceous compounds were the dominant components (totaling approximately 87%) of the PM2.5, similar to the results (greater than 80% of the PM2.5) of our previous study of on-road China III diesel trucks. In general, the amounts of individual component groups (carbonaceous compounds, WSIs, and elements) and PM2.5 emissions for China IV diesel trucks were lower than those of China III diesel trucks of the same size, except for the WSIs and elements for the light- and medium-duty diesel trucks. The EC/OC mass ratios were strongly dependent on the emission standards, and the ratios of China IV diesel trucks were higher than those of China III diesel trucks of the same size. The chemical species in the PM2.5 were significantly affected by the driving conditions. Overall, the emission factors (EFs) of the PM2.5 and OC under non-highway (NHW) driving conditions were higher than those under highway (HW) driving conditions, and the EC/OC mass ratios presented an increasing trend, with decreasing OC/PM2.5 and increasing EC/PM2.5 from NHW to HW driving conditions; similar trends were reported in our previous study. In addition, Pearson's correlation coefficients among the PM2.5 species were analyzed to determine the relationships among the various chemical components. Copyright © 2016 Elsevier B.V. All rights reserved.

Diesel Technology: Engines. Second Edition. Teacher Edition [and] Student Edition.

Science.gov (United States)

Barbieri, Dave; Miller, Roger; Kellum, Mary

This diesel technology series offers secondary and postsecondary students an opportunity for learning required skills in the diesel industry. It aligns with the medium/heavy duty truck task list developed by the National Automotive Technicians Education Foundation and used by the National Institute for Automotive Service Excellence in…

DIESEL ENGINE RETROFIT TECHNOLOGY VERIFICATION

Science.gov (United States)

This presentation wil be given at the EPA Science Forum 2005 in Washington, DC. According to recent estimates, there are approximately 7.9 million heavy-duty diesel trucks and buses in use in the United States. Emissions from these vehicles account for substantial portions of t...

Heavy truck modeling for fuel consumption. Simulations and measurements

Energy Technology Data Exchange (ETDEWEB)

Sandberg, T.

2001-12-01

Fuel consumption for heavy trucks depends on many factors like roads, weather, and driver behavior that are hard for a manufacturer to influence. However, one design possibility is the power train configuration. Here a new simulation program for heavy trucks is created to find the configuration of the power train that gives the lowest fuel consumption for each transport task. For efficient simulations the model uses production code for speed and gear control, and it uses exchangeable data sets to allow simulation of the whole production range of engine types, on recorded road profiles from all over the world. Combined with a graphical user interface this application is called STARS (Scania Truck And Road Simulation). The forces of rolling resistance and air resistance in the model are validated through an experiment where the propeller shaft torque of a heavy truck is measured. It is found that the coefficient of rolling resistance is strongly dependent on tire temperature, not only on vehicle speed as expected. This led to the development of a new model for rolling resistance. The model includes the dynamic behavior of the tires and relates rolling resistance to tire temperature and vehicle speed. In another experiment the fuel consumption of a test truck in highway driving is measured. The altitude of the road is recorded with a barometer and used in the corresponding simulations. Despite of the limited accuracy of this equipment the simulation program manage to predict a level of fuel consumption only 2% lower than the real measurements. It is concluded that STARS is a good tool for predicting fuel consumption for trucks in highway driving and for comparing different power train configurations.

The heavy-duty vehicle future in the United States: A parametric analysis of technology and policy tradeoffs

International Nuclear Information System (INIS)

Askin, Amanda C.; Barter, Garrett E.; West, Todd H.; Manley, Dawn K.

2015-01-01

We present a parametric analysis of factors that can influence advanced fuel and technology deployments in U.S. Class 7–8 trucks through 2050. The analysis focuses on the competition between traditional diesel trucks, natural gas vehicles (NGVs), and ultra-efficient powertrains. Underlying the study is a vehicle choice and stock model of the U.S. heavy-duty vehicle market. The model is segmented by vehicle class, body type, powertrain, fleet size, and operational type. We find that conventional diesel trucks will dominate the market through 2050, but NGVs could have significant market penetration depending on key technological and economic uncertainties. Compressed natural gas trucks conducting urban trips in fleets that can support private infrastructure are economically viable now and will continue to gain market share. Ultra-efficient diesel trucks, exemplified by the U.S. Department of Energy's SuperTruck program, are the preferred alternative in the long haul segment, but could compete with liquefied natural gas (LNG) trucks if the fuel price differential between LNG and diesel increases. However, the greatest impact in reducing petroleum consumption and pollutant emissions is had by investing in efficiency technologies that benefit all powertrains, especially the conventional diesels that comprise the majority of the stock, instead of incentivizing specific alternatives. -- Highlights: •We present a parametric analysis of factors U.S. Class 7–8 trucks through 2050. •Conventional diesels will be more than 70% of U.S. heavy-duty vehicles through 2050. •CNG trucks are well suited to large, urban fleets with private refueling. •Ultra-efficient long haul diesel trucks are preferred over LNG at current fuel prices

Heavy vehicle propulsion system materials program semiannual progress report for April 1999 through September 1999

Energy Technology Data Exchange (ETDEWEB)

Johnson, D.R.

2000-01-01

The purpose of the Heavy Vehicle Propulsion System Materials Program is the development of materials: ceramics, intermetallics, metal alloys, and metal and ceramic coatings, to support the dieselization of class 1-3 trucks to realize a 35% fuel-economy improvement over current gasoline-fueled trucks and to support commercialization of fuel-flexible LE-55 low-emissions, high-efficiency diesel engines for class 7-8 trucks.

SVOC emissions from diesel trucks operating on biodiesel fuels

Science.gov (United States)

This study measured semivolatile organic compounds (SVOCs) in particle matter (PM) emitted from three heavy-duty trucks equipped with modern after-treatment technologies. Emissions testing was conducted as described by the George et al. VOC study also presented as part of this se...

Heavy vehicle propulsion system materials program semiannual progress report for April 1998 thru September 1998

Energy Technology Data Exchange (ETDEWEB)

Johnson, D.R.

1999-01-01

The purpose of the Heavy Vehicle Propulsion System Materials Program is the development of materials: ceramics, intermetallics, metal alloys, and metal and ceramic coatings, to support the dieselization of class 1--3 trucks to realize a 35{percent} fuel-economy improvement over current gasoline-fueled trucks and to support commercialization of fuel-flexible LE-55 low-emissions, high-efficiency diesel engines for class 7--8 trucks. The Office of Transportation Technologies, Office of Heavy Vehicle Technologies (OTT OHVT) has an active program to develop the technology for advanced LE-55 diesel engines with 55{percent} efficiency and low emissions levels of 2.0 g/bhp-h NO{sub x} and 0.05 g/bhp-h particulates. The goal is also for the LE-55 engine to run on natural gas with efficiency approaching that of diesel fuel. The LE-55 program is being completed in FY 1997 and, after approximately 10 years of effort, has largely met the program goals of 55{percent} efficiency and low emissions. However, the commercialization of the LE-55 technology requires more durable materials than those that have been used to demonstrate the goals. Heavy Vehicle Propulsion System Materials will, in concert with the heavy-duty diesel engine companies, develop the durable materials required to commercialize the LE-55 technologies.

Real-world emissions and fuel consumption of diesel buses and trucks in Macao: From on-road measurement to policy implications

Science.gov (United States)

Wu, Xiaomeng; Zhang, Shaojun; Wu, Ye; Li, Zhenhua; Zhou, Yu; Fu, Lixin; Hao, Jiming

2015-11-01

A total of 13 diesel buses and 12 diesel trucks in Macao were tested using portable emission measurement systems (PEMS) including a SEMTECH-DS for gaseous emissions and a SEMTECH-PPMD for PM2.5. The average emission rates of gaseous pollutants and CO2 are developed with the operating mode defined by the instantaneous vehicle specific power (VSP) and vehicle speed. Both distance-based and fuel mass-based emission factors for gaseous pollutants (e.g., CO, THC and NOX) are further estimated under typical driving conditions. The average distance-based NOX emission of heavy-duty buses (HDBs) is higher than 13 g km-1. Considering the unfavorable conditions for selective reductions catalyst (SCR) systems, such as low-speed driving conditions, more effective technology options (e.g., dedicated natural gas buses and electric buses) should be considered by policy makers in Macao. We identified strong effects of the vehicle size, engine displacement and driving conditions on real-world CO2 emission factors and fuel consumption for diesel vehicles. Therefore, detailed profiles regarding vehicle specifications can reduce the uncertainty in their fleet-average on-road fuel consumption. In addition, strong correlations between relative emission factors and driving conditions indicated by the average speed of generated micro-trips are identified based on a micro-trip method. For example, distance-based emission factors of HDBs will increase by 39% for CO, 29% for THC, 43% for NOX and 26% for CO2 when the average speed decreases from 30 km h-1 to 20 km h-1. The mitigation of on-road emissions from diesel buses and trucks by improving traffic conditions through effective traffic and economic management measures is therefore required. This study demonstrates the important role of PEMS in understanding vehicle emissions and mitigation strategies from science to policy perspectives.

The dieselization of America: An integrated strategy for future transportation fuels

Energy Technology Data Exchange (ETDEWEB)

Eberhardt, J.J. [Dept. of Energy, Washington, DC (United States)

1997-12-31

The Diesel Cycle engine has already established itself as the engine-of-choice for the heavy duty transport industry because of its fuel efficiency, durability, and reliability. In addition, it has also been shown to be capable of using alternative fuels, albeit at efficiencies lower than that achieved with petroleum-derived diesel fuel. Alternative fuel dedicated engines have not made significant penetration of the heavy duty truck market because truck fleet operators need a cost-competitive fuel and reliable supply and fueling infrastructure. In lieu of forcing diverse fuels from many diverse domestic feedstocks onto the end-users, the Office of Heavy Vehicle Technologies envisions that a future fuels strategy for the heavy duty transport sector is one where the diverse feedstocks are utilized to provide a single fuel specification (dispensed from the existing fueling infrastructure) that would run efficiently in a single high efficiency energy conversion device, the Diesel Cycle engine. In so doing, the US Commercial transport industry may gain a measure of security from the rapid fuel price increases by relying less on a single feedstock source to meet its increasing fuel requirements.

Heavy vehicle propulsion system materials program semi-annual progress report for October 1997 through March 1998

Energy Technology Data Exchange (ETDEWEB)

Johnson, D.R.

1998-06-01

The purpose of the Heavy Vehicle Propulsion System materials Program is the development of materials: ceramics, intermetallics, metal alloys, and metal and ceramic coatings, to support the dieselization of class 1--3 trucks to realize a 35{percent} fuel-economy improvement over current gasoline-fueled trucks and to support commercialization of fuel-flexible LE-55 low-emissions, high-efficiency diesel engines for class 7--8 trucks. The Office of Transportation Technologies, Office of Heavy Vehicle Technologies (OTT OHVT) has an active program to develop the technology for advanced LE-55 diesel engines with 55{percent} efficiency and low emissions levels of 2.0 g/bhp-h NO{sub x} and 0.05 g/bhp-h particulates. The goal is also for the LE-55 engine to run on natural gas with efficiency approaching that of diesel fuel. The LE-55 program is being completed in FY 1997 and, after approximately 10 years of effort, has largely met the program goals of 55{percent} efficiency and low emissions. However, the commercialization of the LE-55 technology requires more durable materials than those that have been used to demonstrate the goals. Heavy Vehicle Propulsion System Materials will, in concert with the heavy-duty diesel engine companies, develop the durable materials required to commercialize the LE-55 technologies.

Emissions During and Real-world Frequency of Heavy-duty Diesel Particulate Filter Regeneration.

Science.gov (United States)

Ruehl, Chris; Smith, Jeremy D; Ma, Yilin; Shields, Jennifer Erin; Burnitzki, Mark; Sobieralski, Wayne; Ianni, Robert; Chernich, Donald J; Chang, M-C Oliver; Collins, John Francis; Yoon, Seungju; Quiros, David; Hu, Shaohua; Dwyer, Harry

2018-05-15

Recent tightening of particulate matter (PM) emission standards for heavy-duty engines has spurred the widespread adoption of diesel particulate filters (DPFs), which need to be regenerated periodically to remove trapped PM. The total impact of DPFs therefore depends not only on their filtering efficiency during normal operation, but also on the emissions during and the frequency of regeneration events. We performed active (parked and driving) and passive regenerations on two heavy-duty diesel vehicles (HDDVs), and report the chemical composition of emissions during these events, as well as the efficiency with which trapped PM is converted to gas-phase products. We also collected activity data from 85 HDDVs to determine how often regeneration occurs during real-world operation. PM emitted during regeneration ranged from 0.2 to 16.3 g, and the average time and distance between real-world active regenerations was 28.0 h and 599 miles. These results indicate that regeneration of real-world DPFs does not substantially offset the reduction of PM by DPFs during normal operation. The broad ranges of regeneration frequency per truck (3-100 h and 23-4078 miles) underscore the challenges in designing engines and associated aftertreatments that reduce emissions for all real-world duty cycles.

Modeling mechanical restriction differences between car and heavy truck in two-lane cellular automata traffic flow model

Science.gov (United States)

Li, Xin; Li, Xingang; Xiao, Yao; Jia, Bin

2016-06-01

Real traffic is heterogeneous with car and truck. Due to mechanical restrictions, the car and the truck have different limited deceleration capabilities, which are important factors in safety driving. This paper extends the single lane safety driving (SD) model with limited deceleration capability to two-lane SD model, in which car-truck heterogeneous traffic is considered. A car has a larger limited deceleration capability while a heavy truck has a smaller limited deceleration capability as a result of loaded goods. Then the safety driving conditions are different as the types of the following and the leading vehicles vary. In order to eliminate the well-known plug in heterogeneous two-lane traffic, it is assumed that heavy truck has active deceleration behavior when the heavy truck perceives the forming plug. The lane-changing decisions are also determined by the safety driving conditions. The fundamental diagram, spatiotemporal diagram, and lane-changing frequency were investigated to show the effect of mechanical restriction on heterogeneous traffic flow. It was shown that there would be still three traffic phases in heterogeneous traffic condition; the active deceleration of the heavy truck could well eliminate the plug; the lane-changing frequency was low in synchronized flow; the flow and velocity would decrease as the proportion of heavy truck grows or the limited deceleration capability of heavy truck drops; and the flow could be improved with lane control measures.

Heavy Duty Diesel Truck and Bus Hybrid Powertrain Study

Science.gov (United States)

2012-03-01

Electric Vehicles to supply battery modules for Smith’s lineup of zero-emission, all-electric commercial vehicles (CVs). A123 expects to begin...hybrids may have generally improved reliability compared to conventional diesel vehicles, their maintenance procedures are specialized. Hybrid

Speed limiter integrated fatigue analyzer (SLIFA) for speed and fatigue control on diesel engine truck and bus

Science.gov (United States)

Wahyudi, Haris; Pranoto, Hadi; Leman, A. M.; Sebayang, Darwin; Baba, I.

2017-09-01

Every second, the number of road traffic deaths is increased globally with millions more sustaining severe injuries and living with long-term adverse health consequences. Jakarta alone in year 2015 had recorded 556 people died due to road accidents, approximately reached 6.231 road accident cases. The identified major contributory factors of such unfortunate events are both driver fatigue and over speeding habit especially related to the driving of truck and bus. This paper presents the idea on how to control the electronic system from input fuel system of injection pump and the combustion chamber engine will control the valve solenoid in injection pump which can lock and fuel will stop for moment, and speed limit can be success, by using sensor heart rate we can input reduce speed limit when fatigue detection driver. Integration process this tool can be relevant when Speed Limiter Integrated Fatigue Analyser (SLIFA) trial in the diesel engine for truck and bus, the result of this research Speed Limiter Integrated Fatigue Analyser (SLIFA) able to control speed of diesel engine for truck and bus almost 30km/h, 60km/h, and until 70 km/h. The installation of the sensor heart rate as the input speed limit SLIFA would work when the driver is detected to be in the fatigue condition. We make Speed Limiter Integrated Fatigue Analyser (SLIFA) for control and monitoring system for diesel engine in truck and bus. Speed Limiter Integrated Fatigue Analyser (SLIFA) system can save the historical of the speed record, fatigue, rpm, and body temperature of the driver.

Changes in the Canadian diesel industry and their impact on trucking and farming

International Nuclear Information System (INIS)

Sperber, M.; Vail, S.; Clavet, F.

2001-01-01

This study examines the workings of the diesel industry and provides a perspective on several issues that influence the industry, particularly retail pricing and how it affects truckers and farmers. These important users of diesel fuel have expressed concerns regarding the relationships between diesel prices and external factors. The five regions that were examined in depth were Moncton, New Brunswick, Saint-Hyacinthe,Quebec, Winnipeg, Manitoba, Regina, Saskatchewan and Guelph, Ontario. The diesel industry follows the economic rules of supply and demand. The study found that diesel fuel prices at the wholesale level are influenced by world crude oil prices as well as by continental and world conditions. The paper examined the structure, conduct and performance of the wholesale diesel industry as well as its competition. The components that make up the final cost of diesel fuel (such as taxes) were described along with the influence of continental factors that affect the diesel industry. Trucking companies have the flexibility to consider supply options in different regions in North America, depending on the routes they travel. In addition, carriers using large volumes of diesel also pay better prices for fuel than smaller carriers. Farmers use less fuel than truckers and must rely on fuel delivery to their farms. The price of diesel for farmers generally depends on the volume purchased. Grain farmers are affected by diesel fuel costs more than other types of farmers, particularly since they receive very low world prices for their harvest. 7 tabs., 11 figs

DELTA-DIESEL ENGINE LIGHT TRUCK APPLICATION Contract DE-FC05-97OR22606 Final Report

Energy Technology Data Exchange (ETDEWEB)

Hakim, Nabil Balnaves, Mike

2003-05-27

DELTA Diesel Engine Light Truck Application End of Contract Report DE-FC05-97-OR22606 EXECUTIVE SUMMARY This report is the final technical report of the Diesel Engine Light Truck Application (DELTA) program under contract DE-FC05-97-OR22606. During the course of this contract, Detroit Diesel Corporation analyzed, designed, tooled, developed and applied the ''Proof of Concept'' (Generation 0) 4.0L V-6 DELTA engine and designed the successor ''Production Technology Demonstration'' (Generation 1) 4.0L V-6 DELTA engine. The objectives of DELTA Program contract DE-FC05-97-OR22606 were to: Demonstrate production-viable diesel engine technologies, specifically intended for the North American LDT and SUV markets; Demonstrate emissions compliance with significant fuel economy advantages. With a clean sheet design, DDC produced the DELTA engine concept promising the following attributes: 30-50% improved fuel economy; Low cost; Good durability and reliability; Acceptable noise, vibration and harshness (NVH); State-of-the-art features; Even firing, 4 valves per cylinder; High pressure common rail fuel system; Electronically controlled; Turbocharged, intercooled, cooled EGR; Extremely low emissions via CLEAN Combustion{copyright} technology. To demonstrate the engine technology in the SUV market, DDC repowered a 1999 Dodge Durango with the DELTA Generation 0 engine. Fuel economy improvements were approximately 50% better than the gasoline engine replaced in the vehicle.

Designing Optimal LNG Station Network for U.S. Heavy-Duty Freight Trucks using Temporally and Spatially Explicit Supply Chain Optimization

Science.gov (United States)

Lee, Allen

The recent natural gas boom has opened much discussion about the potential of natural gas and specifically Liquefied Natural Gas (LNG) in the United States transportation sector. The switch from diesel to natural gas vehicles would reduce foreign dependence on oil, spur domestic economic growth, and potentially reduce greenhouse gas emissions. LNG provides the most potential for the medium to heavy-duty vehicle market partially due to unstable oil prices and stagnant natural gas prices. As long as the abundance of unconventional gas in the United States remains cheap, fuel switching to natural gas could provide significant cost savings for long haul freight industry. Amid a growing LNG station network and ever increasing demand for freight movement, LNG heavy-duty truck sales are less than anticipated and the industry as a whole is less economic than expected. In spite of much existing and mature natural gas infrastructure, the supply chain for LNG is different and requires explicit and careful planning. This thesis proposes research to explore the claim that the largest obstacle to widespread LNG market penetration is sub-optimal infrastructure planning. No other study we are aware of has explicitly explored the LNG transportation fuel supply chain for heavy-duty freight trucks. This thesis presents a novel methodology that links a network infrastructure optimization model (represents supply side) with a vehicle stock and economic payback model (represents demand side). The model characterizes both a temporal and spatial optimization model of future LNG transportation fuel supply chains in the United States. The principal research goal is to assess the economic feasibility of the current LNG transportation fuel industry and to determine an optimal pathway to achieve ubiquitous commercialization of LNG vehicles in the heavy-duty transport sector. The results indicate that LNG is not economic as a heavy-duty truck fuel until 2030 under current market conditions

Energy Efficiency in Heavy Vehicle Tires, Drivetrains, and Braking Systems; FINAL

International Nuclear Information System (INIS)

Peter J. Blau

2000-01-01

This document was prepared to support the primary goals of the Department of Energy, Office of Heavy Vehicle Technologies. These were recently stated as follows: ''Develop by 2004 the enabling technologies for a class 7-8 truck with a fuel efficiency of 10 mpg (at 65 mph) which will meet prevailing emission standards. For Class 3-6 trucks operating on an urban driving cycle, develop by 2004 commercially viable vehicles that achieve at least double the fuel economy of comparable current vehicles (1999), and as a research goal, reduce criteria pollutants to 30% below EPA standards. Develop by 2004 the diesel engine enabling technologies to support large-scale industry dieselization of Class 1 and 2 trucks, achieving a 35% fuel efficiency improvement over comparable gasoline-fueled trucks, while meeting applicable emissions standards.'' The enabling technologies for improving the fuel efficiency of trucks, include not only engine technologies but also technologies involved with lowering the rolling resistance of tires, reducing vehicle aerodynamic drag, improving thermal management, and reducing parasitic frictional losses in drive train components. Opportunities also exist for making better use of the energy that might ordinarily be dissipated during vehicle braking. Braking systems must be included in this evaluation since safety in truck operations is vital, and braking requirements are greater for vehicles having lowered resistance to rolling. The Office of Heavy Vehicle Technologies has initiated a program to improve the aerodynamics of heavy vehicles through wind tunnel testing, computational modeling, and on-road evaluations. That activity is described in a separate multi-year plan; therefore, emphasis in this document will be on tires, drive trains, and braking systems. Recent, dramatic fluctuations in diesel fuel prices have emphasized the importance of effecting savings in truck fuel economy by implementing new component designs and materials

Technical and economic study of Stirling and Rankine cycle bottoming systems for heavy truck diesel engines

Science.gov (United States)

Kubo, I.

1987-01-01

Bottoming cycle concepts for heavy duty transport engine applications were studied. In particular, the following tasks were performed: (1) conceptual design and cost data development for Stirling systems; (2) life-cycle cost evaluation of three bottoming systems - organic Rankine, steam Rankine, and Stirling cycles; and (3) assessment of future directions in waste heat utilization research. Variables considered for the second task were initial capital investments, fuel savings, depreciation tax benefits, salvage values, and service/maintenance costs. The study shows that none of the three bottoming systems studied are even marginally attractive. Manufacturing costs have to be reduced by at least 65%. As a new approach, an integrated Rankine/Diesel system was proposed. It utilizes one of the diesel cylinders as an expander and capitalizes on the in-cylinder heat energy. The concept eliminates the need for the power transmission device and a sophisticated control system, and reduces the size of the exhaust evaporator. Results of an economic evaluation indicate that the system has the potential to become an attractive package for end users.

Work-related musculoskeletal discomfort among heavy truck drivers.

Science.gov (United States)

Nazerian, Ramtin; Korhan, Orhan; Shakeri, Ehsan

2018-03-13

Heavy truck drivers are exposed to various psychological, psychosocial and physiological factors, some of which can cause musculoskeletal discomfort in different body regions. This study aims to investigate the correlation between different factors of musculoskeletal discomfort in heavy truck drivers. A cross-sectional study design was applied. A total of 384 participants were interviewed using an updated version of the Nordic musculoskeletal questionnaire. While hypothesis testing was used to assess the association of different factors in musculoskeletal discomfort, logistic regression was applied to explore different correlations among questions of the survey. The results demonstrate that hours of exposure to vibration were associated with discomfort in the neck and shoulders (p  0.05. Fifty-seven percent of the drivers were suffering from discomfort in their lower back region. Moreover, seat comfort was found to be highly correlated with discomfort in the neck, shoulder and upper back areas. Additionally, with aging the likelihood of experiencing discomfort in the neck, upper back and knees is increased.

The Detroit Diesel DELTA Engine for Light Trucks and SUVs - Year 2000 Update

Energy Technology Data Exchange (ETDEWEB)

Nabil S. Hakim; Charles E. Freese; Stanley P. Miller

2000-06-19

Detroit Diesel Corporation (DDC) is developing the DELTA 4.0L V6 engine, specifically for the North American light truck market. This market poses unique requirements for a diesel engine, necessitating a clean sheet engine design. DELTA was developed from a clean sheet of paper, with the first engine firing just 228 days later. The process began with a Quality Function Deployment (QFD) analysis, which prioritized the development criteria. The development process integrated a co-located, fully cross-functional team. Suppliers were fully integrated and maintained on-site representation. The first demonstration vehicle moved under its own power 12 weeks after the first engine fired. It was demonstrated to the automotive press 18 days later. DELTA has repeatedly demonstrated its ability to disprove historical North American diesel perceptions and compete directly with gasoline engines. This paper outlines the Generation 0.0 development process and briefly defines the engine. A brief indication of the Generation 0.5 development status is given.

The Detroit Diesel DELTA Engine for Light Trucks and SUVs - Year 2000 Update

International Nuclear Information System (INIS)

Nabil S. Hakim; Charles E. Freese; Stanley P. Miller

2000-01-01

Detroit Diesel Corporation (DDC) is developing the DELTA 4.0L V6 engine, specifically for the North American light truck market. This market poses unique requirements for a diesel engine, necessitating a clean sheet engine design. DELTA was developed from a clean sheet of paper, with the first engine firing just 228 days later. The process began with a Quality Function Deployment (QFD) analysis, which prioritized the development criteria. The development process integrated a co-located, fully cross-functional team. Suppliers were fully integrated and maintained on-site representation. The first demonstration vehicle moved under its own power 12 weeks after the first engine fired. It was demonstrated to the automotive press 18 days later. DELTA has repeatedly demonstrated its ability to disprove historical North American diesel perceptions and compete directly with gasoline engines. This paper outlines the Generation 0.0 development process and briefly defines the engine. A brief indication of the Generation 0.5 development status is given

The Aerodynamics of Heavy Vehicles III : Trucks, Buses and Trains

CERN Document Server

Orellano, Alexander

2016-01-01

This volume contains papers presented at the International conference “The Aerodynamics of Heavy Vehicles III: Trucks, Buses and Trains” held in Potsdam, Germany, September 12-17, 2010 by Engineering Conferences International (ECI). Leading scientists and engineers from industry, universities and research laboratories, including truck and high-speed train manufacturers and operators were brought together to discuss computer simulation and experimental techniques to be applied for the design of more efficient trucks, buses and high-speed trains in the future.   This conference was the third in the series after Monterey-Pacific Groove in 2002 and Lake Tahoe in 2007.  The presentations address different aspects of train aerodynamics (cross wind effects, underbody flow, tunnel aerodynamics and aeroacoustics, experimental techniques), truck aerodynamics (drag reduction, flow control, experimental and computational techniques) as well as computational fluid dynamics and bluff body, wake and jet flows.

Multiyear Program Plan: Reducing Friction and Wear in Heavy Vehicles

Energy Technology Data Exchange (ETDEWEB)

R.R. Fessler; G.R. Fenske

1999-12-13

As described in its multiyear program plan for 1998-2000, the Office of Heavy Vehicle Technologies (OHVT) envisions the development of a fuel-flexible, energy-efficient, near-zero-emissions, heavy-duty U.S. diesel engine technology devolving into all truck classes as a real and viable strategy for reducing energy requirements for commercial transport services and the rapidly growing multipurpose vehicle market (pickups, vans, and sport utility vehicles). Implementation of the OHVT program plan will have significant national benefits in energy savings, cleaner air, more jobs, and increased gross domestic product (GDP). Successful implementation will reduce the petroleum consumption of Class 1-8 trucks by 1.4 million barrels of oil per day by 2020 and over 1.8 million by 2030, amounting to a reduction in highway petroleum consumption of 13.2% and 18.6%, respectively. All types of regulated emissions will be reduced, that is, 20% drop in PM10 emissions (41,000 metric tons per year) by 203 0, 17% reduction in CO2 greenhouse gases (205 million metric tons per year), 7% reduction in NOx, 20% reduction in NMHC, and 30% reduction in CO. An increase of 15,000 jobs by 2020 is expected, as is an increase of $24 billion in GDP. The strategy of OHVT is to focus primarily on the diesel engine since it has numerous advantages. It has the highest efficiency of any engine today, 45% versus 30% for production gasoline engines; and it can be made more efficient at least to 55% and possibly up to 63%. It is the engine of choice for heavy vehicles (trucks), because it offers power, efficiency, durability, and reliability and is used extensively in rail, marine, and off-road applications. Its emission can be ultra-low to near zero, and the production infrastructure is already in place. The primary goals of OHVT are as follows: (1) Develop by 2002 the diesel-engine enabling technologies to support large-scale industry dieselization of light trucks, achieving a 35% fuel efficiency

A novel cascade organic Rankine cycle (ORC) system for waste heat recovery of truck diesel engines

International Nuclear Information System (INIS)

Chen, Tao; Zhuge, Weilin; Zhang, Yangjun; Zhang, Lei

2017-01-01

Highlights: • A confluent cascade expansion ORC (CCE-ORC) system is proposed. • Cyclopentane is considered as the most suitable fluid for this system. • The CCE-ORC system performance under full operating conditions is analyzed. • The BSFC of diesel engine can be reduced by 9.2% with the CCE-ORC system. • Performance comparison of CCE-ORC and dual-loop ORC is conducted. - Abstract: Waste heat recovery (WHR) of engines has attracted increasingly more concerns recently, as it can improve engine thermal efficiency and help truck manufacturers meet the restrictions of CO_2 emission. The organic Rankine cycle (ORC) has been considered as the most potential technology of WHR. To take full advantage of waste heat energy, the waste heat in both exhaust gases and the coolant need to be recovered; however, conventional multi-source ORC systems are too complex for vehicle applications. This paper proposed a confluent cascade expansion ORC (CCE-ORC) system for engine waste heat recovery, which has simpler architecture, a smaller volume and higher efficiency compared with conventional dual-loop ORC systems. Cyclopentane is analyzed to be regarded as the most suitable working fluid for this novel system. A thermodynamic simulation method is established for this system, and off-design performance of main components and the working fluid side pressure drop in the condenser have been taken into consideration. System performance simulations under full engine operating conditions are conducted for the application of this system on a heavy-duty truck diesel engine. Results show that the engine peak thermal efficiency can be improved from 45.3% to 49.5% where the brake specific fuel consumption (BSFC) decreases from 185.6 g/(kW h) to 169.9 g/(kW h). The average BSFC in the frequently operating region can decrease by 9.2% from 187.9 g/(kW h) to 172.2 g/(kW h). Compared with the conventional dual-loop ORC system, the CCE-ORC system can generate 8% more net power, while the

Response of Salix alba L. to heavy metals and diesel fuel ...

African Journals Online (AJOL)

Response of Salix alba L. to heavy metals and diesel fuel contamination. ... Ni and Pb led to reduced accumulation of Pb. Presence of 5 g/kg of diesel fuel in soil significantly increased toxic influence of applied heavy metals by further reducing ... Key words: Cd, Ni, Pb, phytoremediation, phytoextraction, willow, Salix alba.

Field Measurement of Dynamic Compressive Stress Response of Pavement-Subgrade Induced by Moving Heavy-Duty Trucks

Directory of Open Access Journals (Sweden)

Lingshi An

2018-01-01

Full Text Available This paper presents the dynamic compressive stress response of pavement-subgrade induced by moving heavy-duty trucks. In order to study the distribution characteristic of dynamic pressure of pavement-subgrade in more detail, truck loadings, truck speeds, and dynamic pressure distributions at different depths were monitored under twenty-five working conditions on the section of Qiqihar-Nenjiang Highway in Heilongjiang Province, China. The effects of truck loading, truck speed, and depth on dynamic compressive stress response can be concluded as follows: (1 increasing truck loading will increase the dynamic pressure amplitude of subgrade-pavement and dominant frequencies are close to the characteristic frequencies caused by heavy-duty trucks at the speed of 70 km/h; (2 as truck speed increases, the dynamic pressure amplitudes of measuring points have an increasing tendency; the dynamic pressure spectrums are also significantly influenced by truck speed: the higher the truck speed, the wider the spectrum and the higher the dominant frequencies; (3 as depth increases, the dynamic pressure amplitudes of measuring points decrease rapidly. The influence of the front axle decreases gradually until disappearing and the compressive stress superposition phenomenon caused by rear double axles can be found with increasing depth.

Multiyear Program Plan: Reducing Friction and Wear in Heavy Vehicles; FINAL

International Nuclear Information System (INIS)

R.R. Fessler; G.R. Fenske

1999-01-01

As described in its multiyear program plan for 1998-2000, the Office of Heavy Vehicle Technologies (OHVT) envisions the development of a fuel-flexible, energy-efficient, near-zero-emissions, heavy-duty U.S. diesel engine technology devolving into all truck classes as a real and viable strategy for reducing energy requirements for commercial transport services and the rapidly growing multipurpose vehicle market (pickups, vans, and sport utility vehicles). Implementation of the OHVT program plan will have significant national benefits in energy savings, cleaner air, more jobs, and increased gross domestic product (GDP). Successful implementation will reduce the petroleum consumption of Class 1-8 trucks by 1.4 million barrels of oil per day by 2020 and over 1.8 million by 2030, amounting to a reduction in highway petroleum consumption of 13.2% and 18.6%, respectively. All types of regulated emissions will be reduced, that is, 20% drop in PM10 emissions (41,000 metric tons per year) by 2030, 17% reduction in CO2 greenhouse gases (205 million metric tons per year), 7% reduction in NOx, 20% reduction in NMHC, and 30% reduction in CO. An increase of 15,000 jobs by 2020 is expected, as is an increase of$24 billion in GDP. The strategy of OHVT is to focus primarily on the diesel engine since it has numerous advantages. It has the highest efficiency of any engine today, 45% versus 30% for production gasoline engines; and it can be made more efficient at least to 55% and possibly up to 63%. It is the engine of choice for heavy vehicles (trucks), because it offers power, efficiency, durability, and reliability and is used extensively in rail, marine, and off-road applications. Its emission can be ultra-low to near zero, and the production infrastructure is already in place. The primary goals of OHVT are as follows: (1) Develop by 2002 the diesel-engine enabling technologies to support large-scale industry dieselization of light trucks, achieving a 35% fuel efficiency

Black carbon emissions from diesel sources in Russia. Final report

Energy Technology Data Exchange (ETDEWEB)

Kholod, Nazar [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Evans, Meredydd [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-08-31

This report presents a detailed inventory of Russian BC emissions from diesel sources. Drawing on a complete Russian vehicle registry with detailed information about vehicle types and emission standards, this report analyzes BC emissions from diesel on-road vehicles. On-road diesel vehicles emitted 21 Gg of BC in 2014: heavy-duty trucks account for 60% of the on-road BC emissions, while cars represent only 5% (light commercial vehicles and buses account for the remainder). Using Russian activity data and fuel-based emission factors, the report also presents BC emissions from diesel locomotives and ships, off-road engines in industry, construction and agriculture, and generators. The total emissions from diesel sources in Russia are estimated to be 49 Gg of BC in 2014.

Toxicological characterization of diesel engine emissions using biodiesel and a closed soot filter

NARCIS (Netherlands)

Kooter, Ingeborg M.; van Vugt, Marcel A. T. M.; Jedynska, Aleksandra D.; Tromp, Peter C.; Houtzager, Marc M. G.; Verbeek, Ruud P.; Kadijk, Gerrit; Mulderij, Mariska; Krul, Cyrille A. M.

This study was designed to determine the toxicity (oxidative stress, cytotoxicity, genotoxicity) in extracts of combustion aerosols. A typical Euro Ill heavy truck engine was tested over the European Transient Cycle with three different fuels: conventional diesel EN590, biodiesel EN14214 as 8100 and

Study on heavy duty truck stability control by braking force control; Seidoryoku seigyo ni yoru truck no sharyo kyodo anteika ni taisuru ichikosatsu

Energy Technology Data Exchange (ETDEWEB)

Matsuda, K; Shinjo, H; Harada, M; Ohata, K; Sakata, K [Mitsubishi Motors Corp., Tokyo (Japan)

1997-10-01

Now a days we are discussing about the vehicle stability control system which freely controls the braking force of each wheel to apply the yaw t and decelerate the vehicle. The system drastically improve the vehicle cornering performance and stabilize the vehicle behavior in its critical area. This paper discusses a point to notice in case of applying this technique for heavy duty trucks, and describes the possibility of the stabilization for vehicle cornering behavior about heavy duty truck. 3 refs., 10 figs., 2 tabs.

Emissions from Medium-Duty Conventional and Diesel-Electric Hybrid Vehicles; NREL (National Renewable Energy Laboratory)

Energy Technology Data Exchange (ETDEWEB)

Ragatz, A.; Duran, A.; Thornton, M.; Walkowicz, K.

2014-04-02

This presentation discusses the results of emissions testing for medium-duty conventional and diesel-electric hybrid vehicles. Testing was based on a field evaluation approach that utilized the Fleet DNA drive cycle database and NREL’s Renewable Fuels and Lubricants (ReFUEL) Laboratory chassis dynamometer. Vehicles tested included parcel delivery (Class 6 step vans), beverage delivery (Class 8 tractors), and parcel delivery (Class 7 box trucks) vehicles, all with intended service class medium/heavy heavy-duty diesel (MHDD).
Results for fuel economy and tailpipe NOx emissions included: diesel hybrid electric vehicles showed an average fuel economy advantage on identified test cycles: Class 6 Step Vans: 26%; Class 7 Box Trucks: 24.7%; Class 8 Tractors: 17.3%. Vehicle miles traveled is an important factor in determining total petroleum and CO2 displacement. Higher NOx emissions were observed over some test cycles: highly drive cycle dependent; engine-out differences may result from different engine operating point; and selective catalyst reduction temperature may play a role, but does not explain the whole story.

Heavy Vehicle Propulsion System Materials Program semiannual progress report for October 1996 through March 1997

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-07-01

The purpose of the Heavy Vehicle Propulsion System Materials Program is the development of materials: ceramics, intermetallics, metal alloys, and metal and ceramic coatings, to support the dieselization of class 1-3 trucks to realize a 35% fuel-economy improvement over current gasoline-fueled trucks and to support commercialization of fuel-flexible LE-55 low-emissions, high-efficiency diesel engines for class 7-8 trucks. The design of advanced components for high-efficiency diesel engines has, in some cases, pushed the performance envelope for materials of construction past the point of reliable operation. Higher mechanical and tribological stresses and higher temperatures of advanced designs limit the engine designers; advanced materials allow the design of components that may operate reliably at higher stresses and temperatures, thus enabling more efficient engine designs. Advanced materials also offer the opportunity to improve the emissions, NVH, and performance of diesel engines for pickup trucks, vans, and sport utility vehicles. The principal areas of research are: (1) cost effective high performance materials and processing; (2) advanced manufacturing technology; (3) testing and characterization; and (4) materials and testing standards.

Lifecycle-analysis for heavy vehicles

International Nuclear Information System (INIS)

Gaines, L.

1998-01-01

Various alternative fuels and improved engine and vehicle systems have been proposed in order to reduce emissions and energy use associated with heavy vehicles (predominantly trucks). For example, oil companies have proposed improved methods for converting natural gas to zero-aromatics, zero-sulfur diesel fuel via the Fischer-Tropsch process. Major heavy-duty diesel engine companies are working on ways to simultaneously reduce particulate-matter and NOX emissions. The trend in heavy vehicles is toward use of lightweight materials, tires with lower rolling resistance, and treatments to reduce aerodynamic drag. In this paper, we compare the Mecycle energy use and emissions from trucks using selected alternatives, such as Fisher-Tropsch diesel fuel and advanced fuel-efficient engines. We consider heavy-duty, Class 8 tractor-semitrailer combinations for this analysis. The total life cycle includes production and recycling of the vehicle itself, extraction, processing, and transportation of the fuel itself, and vehicle operation and maintenance. Energy use is considered in toto, as well as those portions that are imported, domestic, and renewable. Emissions of interest include greenhouse gases and criteria pollutants. Angonne's Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation (GREET) model is used to generate per-vehicle fuel cycle impacts. Energy use and emissions for materials manufacturing and vehicle disposal are estimated by means of materials information from Argonne studies. We conclude that there are trade-offs among impacts. For example, the lowest fossil energy use does not necessarily result in lowest total energy use, and lower tailpipe emissions may not necessarily result in lower lifecycle emissions of all criteria pollutants

Design and evaluation of fluidized bed heat recovery for diesel engine systems

Science.gov (United States)

Hamm, J. R.; Newby, R. A.; Vidt, E. J.; Lippert, T. E.

1985-01-01

The potential of utilizing fluidized bed heat exchangers in place of conventional counter-flow heat exchangers for heat recovery from adiabatic diesel engine exhaust gas streams was studied. Fluidized bed heat recovery systems were evaluated in three different heavy duty transport applications: (1) heavy duty diesel truck; (2) diesel locomotives; and (3) diesel marine pushboat. The three applications are characterized by differences in overall power output and annual utilization. For each application, the exhaust gas source is a turbocharged-adiabatic diesel core. Representative subposed exhaust gas heat utilization power cycles were selected for conceptual design efforts including design layouts and performance estimates for the fluidized bed heat recovery heat exchangers. The selected power cycles were: organic rankine with RC-1 working fluid, turbocompound power turbine with steam injection, and stirling engine. Fuel economy improvement predictions are used in conjunction with capital cost estimates and fuel price data to determine payback times for the various cases.

Toxicological characterization of diesel engine emissions using biodiesel and a closed soot filter

NARCIS (Netherlands)

Kooter, I.M.; Vugt, M.A.T.M. van; Jedynska, A.D.; Tromp, P.C.; Houtzager, M.M.G.; Verbeek, R.P.; Kadijk, G.; Mulderij, M.; Krul, C.A.M.

2011-01-01

This study was designed to determine the toxicity (oxidative stress, cytotoxicity, genotoxicity) in extracts of combustion aerosols. A typical Euro III heavy truck engine was tested over the European Transient Cycle with three different fuels: conventional diesel EN590, biodiesel EN14214 as B100 and

Analysis of the Journal Bearing Friction Losses in a Heavy-Duty Diesel Engine

Directory of Open Access Journals (Sweden)

Christoph Knauder

2015-04-01

Full Text Available Internal combustion engines (ICE for the use in heavy-duty trucks and buses have to fulfil demanding requirements for both vehicle efficiency as well as for emission of greenhouse gases. Beside the piston assembly the journal bearings are among the largest contributors to friction in the ICE. Through a combination of measurements and validated simulation methods the journal bearing friction losses of a state-of-the-art heavy-duty Diesel engine are investigated for a large range of real world operating conditions. To this task recently developed and extensively validated simulation methods are used together with realistic lubricant models that consider the Non-Newtonian behaviour as well as the piezoviscous effect. In addition, the potential for further friction reduction with the use of ultra-low viscosity lubricants is explored. The results reveal a potential of about 8% friction reduction in the journal bearings using a 0W20 ultra-low viscosity oil with an HTHS-viscosity (The HTHS-viscosity is defined as the dynamic viscosity of the lubricant measured at 150 °C and at a shear rate of 106 s

Simulation of a heavy-duty diesel engine with electrical turbocompounding system using operating charts for turbocharger components and power turbine

International Nuclear Information System (INIS)

Katsanos, C.O.; Hountalas, D.T.; Zannis, T.C.

2013-01-01

Highlights: • A diesel model was developed using charts for turbocharger and power turbine. • The maximum value of bsfc improvement is 4.1% at 100% engine load. • The generated electric power ranges from 23 kW to 62 kW. • Turbocharger turbine efficiency decreases slightly with the power turbine speed. • Turbocompounding increases the average pressure value in the exhaust manifold. - Abstract: In diesel engines, approximately 30–40% of the energy supplied by the fuel is rejected to the ambience through exhaust gases. Therefore, there is a potentiality for further considerable increase of diesel engine efficiency with the utilization of exhaust gas heat and its conversion to mechanical or electrical energy. In the present study, the operational behavior of a heavy-duty (HD) diesel truck engine equipped with an electric turbocompounding system is examined on a theoretical basis. The electrical turbocompounding configuration comprised of a power turbine coupled to an electric generator, which is installed downstream to the turbocharger (T/C) turbine. A diesel engine simulation model has been developed using operating charts for both turbocharger and power turbine. A method for introducing the operating charts into the engine model is described thoroughly. A parametric analysis is conducted with the developed simulation tool, where the varying parameter is the rotational speed of power turbine shaft. In this study, the interaction between the power turbine and the turbocharged diesel engine is examined in detail. The effect of power turbine speed on T/C components efficiencies, power turbine efficiency, exhaust pressure and temperature, engine boost pressure and air to fuel ratio is evaluated. In addition, theoretical results for the potential impact of electrical turbocompounding on the generated electric power, net engine power and relative improvement of brake specific fuel consumption (bsfc) are provided. The critical evaluation of the theoretical

Model development for air conditioning system in heavy duty trucks

NARCIS (Netherlands)

Kessels, J.T.B.A.; van den Bosch, P.P.J.; Zhang, Quansheng; Li, Shengbo Eben; Deng, Kun

2016-01-01

This chapter presents a modelling approach for the air conditioning (AC) system in heavy duty trucks. The presented model entails two major elements: a mechanical compressor model and a thermal AC model. The compressor model describes the massflow of the refrigerant as well as the mechanical power

Diesel Fueled SOFC for Class 7/Class 8 On-Highway Truck Auxiliary Power

Energy Technology Data Exchange (ETDEWEB)

Vesely, Charles John-Paul [Cummins Power Generation; Fuchs, Benjamin S. [Cummins Power Generation; Booten, Chuck W. [Protonex Technology, LLC

2010-03-31

The following report documents the progress of the Cummins Power Generation (CPG) Diesel Fueled SOFC for Class 7/Class 8 On-Highway Truck Auxiliary Power (SOFC APU) development and final testing under the U.S. Department of Energy (DOE) Energy Efficiency and Renewable Energy (EERE) contract DE-FC36-04GO14318. This report overviews and summarizes CPG and partner development leading to successful demonstration of the SOFC APU objectives and significant progress towards SOFC commercialization. Significant SOFC APU Milestones: Demonstrated: Operation meeting SOFC APU requirements on commercial Ultra Low Sulfur Diesel (ULSD) fuel. SOFC systems operating on dry CPOX reformate. Successful start-up and shut-down of SOFC APU system without inert gas purge. Developed: Low cost balance of plant concepts and compatible systems designs. Identified low cost, high volume components for balance of plant systems. Demonstrated efficient SOFC output power conditioning. Demonstrated SOFC control strategies and tuning methods.

Robust Emission Management Strategy to Meet Real-World Emission Requirements for HD Diesel Engines

NARCIS (Netherlands)

Mentink, P.; Nieuwenhof, R. van den; Kupper, F.; Willems, F.; Kooijman, D.

2015-01-01

Heavy-duty diesel engines are used in different application areas, like long-haul, city distribution, dump truck and building and construction industry. For these wide variety of areas, the engine performance needs to comply with the real-world legislation limits and should simultaneously have a low

Robust emission management strategy to meet real-world emission requirements for HD diesel engines

NARCIS (Netherlands)

Mentink, P.R.; Nieuwenhof, van den R.; Kupper, F.; Willems, F.P.T.; Kooijman, D.

2015-01-01

Heavy-duty diesel engines are used in different application areas, like long-haul, city distribution, dump truck and building and construction industry. For these wide variety of areas, the engine performance needs to comply with the real-world legislation limits and should simultaneously have a low

CNG/diesel buses for Texas school districts

International Nuclear Information System (INIS)

Armstrong, J.H.

1993-01-01

At the present time, the preponderance of trucks, buses and other heavy duty vehicles are powered by diesel engines. The reasons for the change from gasoline to diesel engines are all basically economic, due to the longer life and lower operating costs of diesel engines, as compared to gasoline engines. This provides a compelling reason to continue to use these engines, even if powered by fuel other than diesel. A major strategy within the industry has been the various attempts to adapt diesel engines to alternative fuels. These conversions have been largely to either methanol or natural gas, with propane joining the race just recently. This strategy takes advantage of the remaining life of existing vehicles by converting engines rather than purchasing a new engine (and/or vehicle) designed for and dedicated to an alternate fuel. Although diesel engines have been converted to run on natural gas, there are substantial challenges that must be met. The following describes some of the technical approaches being used for diesel engine conversions

Emission Performance of Low Cetane Naphtha as Drop-In Fuel on a Multi-Cylinder Heavy-Duty Diesel Engine and Aftertreatment System

Energy Technology Data Exchange (ETDEWEB)

LeePhD, John [Aramco Services Company; TzanetakisPhD, Tom [Aramco Services Company; Travers, Michael [Aramco Services Company; Storey, John Morse [ORNL; DeBusk, Melanie Moses [ORNL; Lance, Michael J [ORNL; Partridge Jr, William P [ORNL

2017-01-01

With higher volatility and longer ignition delay characteristics than typical diesel fuel, low cetane naphtha fuel has been shown to promote partially premixed combustion and produce lower soot for improved fuel economy. In this study, emission performance of low cetane, low octane naphtha (CN 35, RON 60) as a drop-in fuel was examined on a MY13 Cummins ISX15 6-cylinder heavy-duty on-highway truck engine and aftertreatment system. Using the production hardware and development calibrations, both the engine-out and tailpipe emissions of naphtha and ultra-low sulfur diesel (ULSD) fuels were examined during the EPA s heavy-duty emission testing cycles. Without any modification to the calibrations, the tailpipe emissions were comparable when using naphtha or ULSD on the heavy duty Federal Test Procedure (FTP) and ramped modal cycle (RMC) test cycles. Overall lower CO2 emissions and fuel consumption were also measured for naphtha due in part to its higher heating value and higher hydrogen to carbon ratio. Engine-out and tailpipe NOx emissions were lower for naphtha fuel at the same catalyst conversion levels and measured particulate matter (PM) emissions were also lower when using naphtha due to its higher volatility and lower aromatic content compared to ULSD. To help assess the potential impact on diesel particulate filter design and operation, engine-out PM samples were collected and characterized at the B50 operating point. A significant reduction in elemental carbon (EC) within the particulate emissions was found when using naphtha compared to ULSD.

The GREET Model Expansion for Well-to-Wheels Analysis of Heavy-Duty Vehicles

Energy Technology Data Exchange (ETDEWEB)

Cai, Hao [Argonne National Lab. (ANL), Argonne, IL (United States); Burnham, Andrew [Argonne National Lab. (ANL), Argonne, IL (United States); Wang, Michael [Argonne National Lab. (ANL), Argonne, IL (United States); Hang, Wen [Argonne National Lab. (ANL), Argonne, IL (United States); Vyas, Anant [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-05-01

Heavy-duty vehicles (HDVs) account for a significant portion of the U.S. transportation sector’s fuel consumption, greenhouse gas (GHG) emissions, and air pollutant emissions. In our most recent efforts, we expanded the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREETTM) model to include life-cycle analysis of HDVs. In particular, the GREET expansion includes the fuel consumption, GHG emissions, and air pollutant emissions of a variety of conventional (i.e., diesel and/or gasoline) HDV types, including Class 8b combination long-haul freight trucks, Class 8b combination short-haul freight trucks, Class 8b dump trucks, Class 8a refuse trucks, Class 8a transit buses, Class 8a intercity buses, Class 6 school buses, Class 6 single-unit delivery trucks, Class 4 single-unit delivery trucks, and Class 2b heavy-duty pickup trucks and vans. These vehicle types were selected to represent the diversity in the U.S. HDV market, and specific weight classes and body types were chosen on the basis of their fuel consumption using the 2002 Vehicle Inventory and Use Survey (VIUS) database. VIUS was also used to estimate the fuel consumption and payload carried for most of the HDV types. In addition, fuel economy projections from the U.S. Energy Information Administration, transit databases, and the literature were examined. The U.S. Environmental Protection Agency’s latest Motor Vehicle Emission Simulator was employed to generate tailpipe air pollutant emissions of diesel and gasoline HDV types.

Life-cycle implications of hydrogen fuel cell electric vehicle technology for medium- and heavy-duty trucks

Science.gov (United States)

Lee, Dong-Yeon; Elgowainy, Amgad; Kotz, Andrew; Vijayagopal, Ram; Marcinkoski, Jason

2018-07-01

This study provides a comprehensive and up-to-date life-cycle comparison of hydrogen fuel cell electric trucks (FCETs) and their conventional diesel counterparts in terms of energy use and air emissions, based on the ensemble of well-established methods, high-fidelity vehicle dynamic simulations, and real-world vehicle test data. For the centralized steam methane reforming (SMR) pathway, hydrogen FCETs reduce life-cycle or well-to-wheel (WTW) petroleum energy use by more than 98% compared to their diesel counterparts. The reduction in WTW air emissions for gaseous hydrogen (G.H2) FCETs ranges from 20 to 45% for greenhouse gases, 37-65% for VOC, 49-77% for CO, 62-83% for NOx, 19-43% for PM10, and 27-44% for PM2.5, depending on vehicle weight classes and truck types. With the current U.S. average electricity generation mix, FCETs tend to create more WTW SOx emissions than their diesel counterparts, mainly because of the upstream emissions related to electricity use for hydrogen compression/liquefaction. Compared to G.H2, liquid hydrogen (L.H2) FCETs generally provide smaller WTW emissions reductions. For both G.H2 and L.H2 pathways for FCETs, because of electricity consumption for compression and liquefaction, spatio-temporal variations of electricity generation can affect the WTW results. FCETs retain the WTW emission reduction benefits, even when considering aggressive diesel engine efficiency improvement.

Dynamic simulation of collisions of heavy high-speed trucks with concrete barriers

International Nuclear Information System (INIS)

Itoh, Yoshito; Liu, Chunlu; Kusama, Ryuichi

2007-01-01

Real vehicle collision experiments on full-scale road safety barriers are important to determine the outcome of a vehicle versus barrier impact accident. However, such experiments require large investment of time and money. Numerical simulation has therefore been imperative as an alternative method for testing concrete barriers. In this research, spring subgrade models were first developed to simulate the ground boundary of concrete barriers. Both heavy trucks and concrete barriers were modeled using finite element methods (FEM) to simulate dynamic collision performances. Comparison of the results generated from computer simulations and on-site full-scale experiments demonstrated that the developed models could be applied to simulate the collision of heavy trucks with concrete barriers to provide the data to design new road safety barriers and analyze existing ones

Experimental comparison of R123 and R245fa as working fluids for waste heat recovery from heavy-duty diesel engine

International Nuclear Information System (INIS)

Shu, Gequn; Zhao, Mingru; Tian, Hua; Huo, Yongzhan; Zhu, Weijie

2016-01-01

Organic Rankine Cycle (ORC) on-board is a solution for vehicles to save energy and reduce emission. Considering the characteristics of waste heat from vehicle, the criterions of the suitable working fluid are very strict. R123 and R245fa have been widely used in companies and labs, however, the difference of their properties under different engine conditions still requires further study. During this research, a series of experiments have been done to compare the performance of these two working fluids, what's more, to determine under which engine conditions they are suitable separately. These experimental comparisons are new and important for the targeting design of ORC for vehicles. The result shows that, considering the difference of thermodynamic properties and the limited cooling capacity on board, R123 shows its advantage for the waste heat recovery at heavy duty, while R245fa is more suitable at light-and-medium duty. These properties make R123 suitable for the ORC designed for long-haul heavy-duty truck, while R245fa is suggested for city bus. The following performance test of R123 for waste heat recovery from heavy-duty diesel engine shows that the maximum fuel consumption improvement can be as much as 2.8%. - Highlights: • R123 is more suitable for heavy duty and steady working condition. • R245fa shows its advantage at light-and-medium duty and varying working condition. • R123 suits better for long-haul heavy-duty truck, while R245fa for city bus. • The maximum fuel consumption improvement is as much as 2.8%.

Effects of diesel/ethanol dual fuel on emission characteristics in a heavy-duty diesel engine

Science.gov (United States)

Liu, Junheng; Sun, Ping; Zhang, Buyun

2017-09-01

In order to reduce emissions and diesel consumption, the gas emissions characteris-tics of diesel/aqueous ethanol dual fuel combustion (DFC) were carried out on a heavy-duty turbocharged and intercooled automotive diesel engine. The aqueous ethanol is prepared by a blend of anhydrous ethanol and water in certain volume proportion. In DFC mode, aqueous ethanol is injected into intake port to form homogeneous charge, and then ignited by the diesel fuel. Results show that DFC can reduce NOx emissions but increase HC and CO emissions, and this trend becomes more prominent with the increase of water blending ratio. Increased emissions of HC and CO could be efficiently cleaned by diesel oxidation catalytic converter (DOC), even better than those of diesel fuel. It is also found that DFC mode reduces smoke remarkably, while increases some unconventional emissions such as formaldehyde and acetal-dehyde. However, unconventional emissions could be reduced approximately to the level of baseline engine with a DOC.

ENVIRONMENTAL TECHNOLOGY VERIFICATION OF EMISSION CONTROLS FOR HEAVY-DUTY DIESEL ENGINES

Science.gov (United States)

While lower emissions limits that took effect in 2004 and reduced sulfur content in diesel fuels will reduce emissions from new heavy-duty engines, the existing diesel fleet, which pollutes at much higher levels, may still have a lifetime of 20 to 30 years. Fleet operators seekin...

Integrated energy and emission management for heavy-duty diesel engines with waste heat recovery system

NARCIS (Netherlands)

Willems, F.P.T.; Kupper, F.; Rascanu, G.; Feru, E.

2015-01-01

Rankine-cycleWasteHeatRecovery (WHR)systems are promising solutions to reduce fuel consumption for trucks. Due to coupling between engine andWHR system, control of these complex systems is challenging. This study presents an integrated energy and emission management strategy for an Euro-VI Diesel

Assessment of on-road emissions of four Euro V diesel and CNG waste collection trucks for supporting air-quality improvement initiatives in the city of Milan

Energy Technology Data Exchange (ETDEWEB)

Fontaras, Georgios, E-mail: georgios.fontaras@jrc.ec.europa.eu [Institute for Energy and Transport, Joint Research Centre, Ispra (Italy); Martini, Giorgio; Manfredi, Urbano; Marotta, Alessandro; Krasenbrink, Alois [Institute for Energy and Transport, Joint Research Centre, Ispra (Italy); Maffioletti, Francesco; Terenghi, Roberto; Colombo, Mauro [AMSA, Azienda Milanese Servizi Ambientali, Milano (Italy)

2012-06-01

This paper summarizes the results of an extensive experimental study aiming to evaluate the performance and pollutant emissions of diesel and CNG waste collection trucks under realistic and controlled operating conditions in order to support a fleet renewal initiative in the city of Milan. Four vehicles (1 diesel and 3 CNG) were tested in two phases using a portable emission measurement system. The first phase included real world operation in the city of Milan while the second involved controlled conditions in a closed track. Emissions recorded from the diesel truck were on average 2.4 kg/km for CO{sub 2}, 0.21 g/km for HC, 7.4 g/km for CO, 32.3 g/km for NO{sub x} and 46.4 mg/km for PM. For the CNG the values were 3.6 kg/km for CO{sub 2}, 2.19 g/km for HC, 15.8 g/km for CO, 4.38 g/km for NO{sub x} and 11.4 mg/km for PM. CNG vehicles presented an important advantage with regards to NO{sub x} and PM emissions but lack the efficiency of their diesel counterparts when it comes to CO, HC and particularly greenhouse gas emissions. This tradeoff needs to be carefully analyzed prior to deciding if a fleet should be shifted towards either technology. In addition it was shown that existing emission factors, used in Europe for environmental assessment studies, reflect well the operation for CNG but were not so accurate when it came to the diesel engine truck particularly for CO{sub 2} and NO{sub x}. With regard to NO{sub x}, it was also shown that the limits imposed by current emission standards are not necessarily reflected in real world operation, under which the diesel vehicle presented almost 4 times higher emissions. Regarding CO{sub 2}, appropriate use of PEMS data and vehicle information allows for accurate emission monitoring through computer simulation. - Highlights: Black-Right-Pointing-Pointer Investigated diesel and CNG Euro V waste collection vehicles for municipal use Black-Right-Pointing-Pointer NO{sub x}-GhG emission trade-off should be considered prior to

Investigation on the effect of heavy diesel fraction properties on product sulphur during ultra deep diesel hydrodesulphurization

Energy Technology Data Exchange (ETDEWEB)

Stratiev, D.; Tzingov, T. [Research and Development Dept., Lukoil Neftochim Bourgas, Bourgas (Bulgaria); Galkin, V. [Future Development Dept., Lukoil Neftochim Bourgas, Bourgas (Bulgaria)

2006-02-01

This work investigates the hydrotreatment of heavy diesel fractions in order to achieve product sulphurs of 50 and 10 ppm. The heavy diesel fractions were obtained in the Lukoil Neftochim Bulgaria (LNB) crude distillation and vacuum distillation units (SRGO1, SRGO2, AGO, LVGO ASTM D-86 95%vol. of 360, 392 395, and 377 C respectively) by distillation of crude oil type ''Ural'', containing some quantities of naphtha, atmospheric residue, vacuum gas oil and low sulphur crude oil, in the mild hydrocracking unit (MHC diesel 95%vol. of 389 C) and in the fluid catalytic cracking unit - heavy cycle oil (FCC HCO; 95%vol. of 360 C). The diesel fractions were hydrotreated in a trickle bed pilot plant at following conditions: reactor inlet temperature range of 300-380 C; liquid hourly space velocity (LHSV) range of 0.5-3.0 h{sup -1}, total reactor pressure range of 3.5- 7.0 MPa; treating gas/feedstock ratio of 250 Nm{sup 3}/m{sup 3}. It was found that in the investigated range of operating conditions the product sulphur depended linearly on the LHSV. As a measure of the diesel hydrodesulphurization (HDS) reactivity the LHSV at 360 C reactor inlet temperature was interpolated at a constant product sulphur level of 50 ppm and extrapolated at 10 ppm sulphur. It was found that the most refractory feedstock was the diesel mixture 80%SRGO1 / 20%FCCHCO (LHSV of 0.4 h{sup -1} for 50 ppm and 0.2 h{sup -1} for 10 ppm sulphur). The catalyst volume increase required to reduce the product sulphur from 50 to 10 ppm was found to be as high as twice for all diesel fractions except the MHC diesel. This material required five times the catalyst volume for the product sulphur reduction from 50 to 10 ppm. The total reactor pressure was found to have less impact on the product sulphur than the LHSV. Doubling the reactor pressure from 3.5 to 7.0 MPa by hydrotreatment of LVGO reduced the product sulphur as low as twice while the reduction of the LHSV from 1 to 0.5 h{sup -1} at a

Natural attenuation of diesel fuel in heavy clay soil

International Nuclear Information System (INIS)

Berry, K.A.T.; Burton, D.L.

1997-01-01

The application of bioremediation techniques on heavy clay soils contaminated with diesel fuels was studied. Earlier studies suggested that in-situ bioreclamation was only effective on permeable soils such as medium- to coarse-textured sandy or loamy soils. It was assumed that heavy clay soils such as those found in the Red River Valley in Southern Manitoba had physical and chemical properties that would limit the usefulness of natural attenuation. In this study, the disappearance and the natural attenuation of diesel fuel added to soil at a rate of 5000 mg/kg soil in tilled and untilled heavy clay soil was monitored. Three methods of analysis were used: (1) oil and grease content, (2) extractable organics, and (3) the Millipore EnviroGard ELISA method for petroleum hydrocarbons. Effects of the contamination on the soil microbial population were measured using surface CO 2 flux measurements and microbial biomass carbon analysis. Soil moisture contents at all sample times were between 44 and 49 per cent. Soil temperature was also monitored. All three analytical methods used in the study showed the near-complete disappearance of detectable diesel fuel hydrocarbons from the soil after 30 days with half-lives ranging from 11 to 26 days. The advantages and limitations of the ELISA kit were described. No hydrocarbons were detected in the groundwater sample. 45 refs., 7 tabs., 2 figs

40 CFR Appendix X to Part 86 - Sampling Plans for Selective Enforcement Auditing of Heavy-Duty Engines and Light-Duty Trucks

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Sampling Plans for Selective Enforcement Auditing of Heavy-Duty Engines and Light-Duty Trucks X Appendix X to Part 86 Protection of... Plans for Selective Enforcement Auditing of Heavy-Duty Engines and Light-Duty Trucks Table 1—Sampling...

Estimating the supply and demand for commercial heavy truck parking on interstate highways : a case study of I-81 in Virginia.

Science.gov (United States)

2002-01-01

The increasing number of trucks traveling on Virginia highways has led to a growing demand for public rest areas and private truck stops. This study developed a methodology to determine the supply and demand for commercial heavy truck parking using I...

Final Rule for Control of Air Pollution From New Motor Vehicles and New Motor Vehicle Engines; Non-Conformance Penalties for 2004 and later Model Year Emission Standards for Heavy-Duty Diesel Engines and Heavy-Duty Diesel Vehicles

Science.gov (United States)

Final Rule for Control of Air Pollution From New Motor Vehicles and New Motor Vehicle Engines; Non-Conformance Penalties for 2004 and later Model Year Emission Standards for Heavy-Duty Diesel Engines and Heavy-Duty Diesel Vehicles

Diesel-powered Passenger Cars and Light Trucks

Science.gov (United States)

2015-10-01

Diesel-powered automobiles are in the news following emission concerns raised by the U.S. Environmental Protection Agency. This fact sheet contains background information on diesel-powered motor vehicles and diesel fuel.

On-line energy and battery thermal management for hybrid electric heavy-duty truck

NARCIS (Netherlands)

Pham, H.T.; Kessels, J.T.B.A.; Bosch, van den P.P.J.; Huisman, R.G.M.; Nevels, R.M.P.A.

2013-01-01

This paper discusses an integrated approach for energy and thermal management to minimize the fuel consumption of a hybrid electric heavy-duty truck. Conventional Energy Management Systems (EMS) operate separately from the Battery Thermal Management System (BTMS) in Hybrid Electric Vehicles (HEVs).

Unregulated greenhouse gas and ammonia emissions from current technology heavy-duty vehicles.

Science.gov (United States)

Thiruvengadam, Arvind; Besch, Marc; Carder, Daniel; Oshinuga, Adewale; Pasek, Randall; Hogo, Henry; Gautam, Mridul

2016-11-01

The study presents the measurement of carbonyl, BTEX (benzene, toluene, ethyl benzene, and xylene), ammonia, elemental/organic carbon (EC/OC), and greenhouse gas emissions from modern heavy-duty diesel and natural gas vehicles. Vehicles from different vocations that included goods movement, refuse trucks, and transit buses were tested on driving cycles representative of their duty cycle. The natural gas vehicle technologies included the stoichiometric engine platform equipped with a three-way catalyst and a diesel-like dual-fuel high-pressure direct-injection technology equipped with a diesel particulate filter (DPF) and a selective catalytic reduction (SCR). The diesel vehicles were equipped with a DPF and SCR. Results of the study show that the BTEX emissions were below detection limits for both diesel and natural gas vehicles, while carbonyl emissions were observed during cold start and low-temperature operations of the natural gas vehicles. Ammonia emissions of about 1 g/mile were observed from the stoichiometric natural gas vehicles equipped with TWC over all the driving cycles. The tailpipe GWP of the stoichiometric natural gas goods movement application was 7% lower than DPF and SCR equipped diesel. In the case of a refuse truck application the stoichiometric natural gas engine exhibited 22% lower GWP than a diesel vehicle. Tailpipe methane emissions contribute to less than 6% of the total GHG emissions. Modern heavy-duty diesel and natural gas engines are equipped with multiple after-treatment systems and complex control strategies aimed at meeting both the performance standards for the end user and meeting stringent U.S. Environmental Protection Agency (EPA) emissions regulation. Compared to older technology diesel and natural gas engines, modern engines and after-treatment technology have reduced unregulated emissions to levels close to detection limits. However, brief periods of inefficiencies related to low exhaust thermal energy have been shown to

Comparison of life cycle greenhouse gases from natural gas pathways for medium and heavy-duty vehicles.

Science.gov (United States)

Tong, Fan; Jaramillo, Paulina; Azevedo, Inês M L

2015-06-16

The low-cost and abundant supply of shale gas in the United States has increased the interest in using natural gas for transportation. We compare the life cycle greenhouse gas (GHG) emissions from different natural gas pathways for medium and heavy-duty vehicles (MHDVs). For Class 8 tractor-trailers and refuse trucks, none of the natural gas pathways provide emissions reductions per unit of freight-distance moved compared to diesel trucks. When compared to the petroleum-based fuels currently used in these vehicles, CNG and centrally produced LNG increase emissions by 0-3% and 2-13%, respectively, for Class 8 trucks. Battery electric vehicles (BEVs) powered with natural gas-produced electricity are the only fuel-technology combination that achieves emission reductions for Class 8 transit buses (31% reduction compared to the petroleum-fueled vehicles). For non-Class 8 trucks (pick-up trucks, parcel delivery trucks, and box trucks), BEVs reduce emissions significantly (31-40%) compared to their diesel or gasoline counterparts. CNG and propane achieve relatively smaller emissions reductions (0-6% and 19%, respectively, compared to the petroleum-based fuels), while other natural gas pathways increase emissions for non-Class 8 MHDVs. While using natural gas to fuel electric vehicles could achieve large emission reductions for medium-duty trucks, the results suggest there are no great opportunities to achieve large emission reductions for Class 8 trucks through natural gas pathways with current technologies. There are strategies to reduce the carbon footprint of using natural gas for MHDVs, ranging from increasing vehicle fuel efficiency, reducing life cycle methane leakage rate, to achieving the same payloads and cargo volumes as conventional diesel trucks.

Cost-effective energy management for hybrid electric heavy-duty truck including battery aging

NARCIS (Netherlands)

Pham, H.T.; Bosch, van den P.P.J.; Kessels, J.T.B.A.; Huisman, R.G.M.

2013-01-01

Battery temperature has large impact on battery power capability and battery life time. In Hybrid Electric Heavy-duty trucks (HEVs), the high-voltage battery is normally equipped with an active Battery Thermal Management System (BTMS) guaranteeing a desired battery life time. Since the BTMS can

Co-simulation of heavy truck tire dynamics and electronic stability control systems (phase A).

Science.gov (United States)

2009-07-01

Electronic stability control (ESC) systems have been proven to be an effective means of preventing instability and loss of control on both passenger vehicles and heavy trucks. In addition, roll stability algorithms are an effective means of reducing ...

Influences on Energy Savings of Heavy Trucks Using Cooperative Adaptive Cruise Control

Energy Technology Data Exchange (ETDEWEB)

Lammert, Michael P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); McAuliffe, Brian [National Research Council Canada; Lu, Xiao-Yun [University of California-Berkeley; Shladover, Steven [University of California-Berkeley; Surcel, Marius-Dorin [FPInnovations; Kailas, Aravind [Volvo Group

2018-04-03

An integrated adaptive cruise control (ACC) and cooperative ACC (CACC) was implemented and tested on three heavy-duty tractor-trailer trucks on a closed test track. The first truck was always in ACC mode, and the followers were in CACC mode using wireless vehicle-vehicle communication to augment their radar sensor data to enable safe and accurate vehicle following at short gaps. The fuel consumption for each truck in the CACC string was measured using the SAE J1321 procedure while travelling at 65 mph and loaded to a gross weight of 65,000 lb, demonstrating the effects of: inter-vehicle gaps (ranging from 3.0 s or 87 m to 0.14 s or 4 m, covering a much wider range than previously reported tests), cut-in and cut-out maneuvers by other vehicles, speed variations, the use of mismatched vehicles (standard trailers mixed with aerodynamic trailers with boat tails and side skirts), and the presence of a passenger vehicle ahead of the platoon. The results showed that energy savings generally increased in a non-linear fashion as the gap was reduced. The middle truck saved the most fuel at gaps shorter than 12 m and the trailing truck saved the most at longer gaps, while lead truck saved the least at all gaps. The cut-in and cut-out maneuvers had only a marginal effect on fuel consumption even when repeated every two miles. The presence of passenger-vehicle traffic had a measurable impact. The fuel-consumption savings on the curves was less than on the straight sections.

Final Rule for Nonconformance Penalties for On-Highway Heavy-Duty Diesel Engines

Science.gov (United States)

EPA is taking final action to establish nonconformance penalties (NCPs) for manufacturers of heavy heavy-duty diesel engines (HHDDE) in model years 2012 and later for emissions of oxides of nitrogen (NOX) because we have found the criteria for NCPs.

Analysis of major trends in U.S. commercial trucking, 1977-2002.

Energy Technology Data Exchange (ETDEWEB)

Bertram, K. M.; Santini, D .J.; Vyas, A. D.

2009-06-10

This report focuses on various major long-range (1977-2002) and intermediate-range (1982-2002) U.S. commercial trucking trends. The primary sources of data for this period were the U.S. Bureau of the Census Vehicle Inventory and Use Survey and Truck Inventory and Use Survey. In addition, selected 1977-2002 data from the U.S. Department of Energy/Energy Information Administration and from the U.S. Department of Transportation/Federal Highway Administration's Highway Statistics were used. The report analyzes (1) overall gasoline and diesel fuel consumption patterns by passenger vehicles and trucks and (2) the population changes and fuels used by all commercial truck classes by selected truck type (single unit or combination), during specified time periods, with cargo-hauling commercial trucks given special emphasis. It also assesses trends in selected vehicle miles traveled, gallons per vehicle miles traveled, and gallons per cargo ton-mile traveled, as well as the effect of cargo tons per truck on fuel consumption. In addition, the report examines long-range trends for related factors (e.g., long-haul mileages driven by heavy trucks) and their impacts on reducing fuel consumption per cargo-ton-mile and the relative shares of total commercial fuel use among truck classes. It identifies the effects of these trends on U.S. petroleum consumption. The report also discusses basic engineering design and performance, national legislation on interstate highway construction, national demographic trends (e.g., suburbanization), and changes in U.S. corporate operations requirements, and it highlights their impacts on both the long-distance hauling and shorter-distance urban and suburban delivery markets of the commercial trucking industry.

Heavy truck restrictions and air quality implications in São Paulo, Brazil.

Science.gov (United States)

Pérez-Martínez, Pedro José; de Fátima Andrade, María; de Miranda, Regina Maura

2017-11-01

This study quantified the effects of traffic restrictions on diesel fuel heavy vehicles (HVs) on the air quality of the Bandeirantes corridor using hourly data obtained by continuous monitoring of traffic and air quality at sites located on this avenue. The study addressed the air quality of a city impacted by vehicular emissions and that PM 10 and NO X concentrations are mainly due to diesel burning. Data collection was split into two time periods, a period of no traffic constraint on HVs (Nov 2008 and 2009) and a period of constraint (Nov 2010, 2011 and 2012). We found that pollutants on this corridor, mainly PM 10 and NO X , decreased significantly during the period from 2008 to 2012 (28 and 43%, 15.8 and 86.9 ppb) as a direct consequence of HV traffic restrictions (a 72% reduction). Rebound effects in the form of increased traffic of light vehicles (LVs) during this time had impacts on the concentration levels, explaining the differences between rates of reduction in HV traffic and pollutants. Reductions in the number of trucks resulted in longer travel times and increased traffic congestion as a consequence of the modal shift towards LVs. We found that a 51% decrease in PM 10 (28.8 μg m -3 ) was due to a reduction in HV traffic (vehicle emissions were estimated to be 71% of total sources, 40.1 μg m -3 ). This percentage was partially offset by 10% more PM 10 emissions related to an increase in LV traffic, while other causes, such as climatic conditions, contributed to a 13% increase in PM 10 concentrations. The relationships analyzed in this research served to highlight the need to apply urban transport policies aimed at decreasing pollutant concentrations in São Paulo, especially in heavily congested urban corridors on working days. Copyright © 2017 Elsevier Ltd. All rights reserved.

Integrated vehicle-based safety systems (IVBSS) : heavy truck platform field operational test data analysis plan.

Science.gov (United States)

2009-11-23

This document presents the University of Michigan Transportation Research Institutes plan to perform : analysis of data collected from the heavy truck platform field operational test of the Integrated Vehicle- : Based Safety Systems (IVBSS) progra...

Development and experimental testing of a hybrid Stirling engine-adsorption chiller auxiliary power unit for heavy trucks

International Nuclear Information System (INIS)

Flannery, Barry; Lattin, Robert; Finckh, Oliver; Berresheim, Harald; Monaghan, Rory F.D.

2017-01-01

Highlights: • Free-piston Stirling engine for truck APU. • Waste heat driven adsorption chiller for cab air conditioning. • Reduced-order model comparing proposed system to existing technology. • Experimental test data from prototype test rig. - Abstract: This paper identifies the key technical requirements for a heavy truck auxiliary power unit (APU) and explores a potential alternative technology for use in a next-generation APU which could eliminate key problems related to emissions, noise and maintenance experienced today by conventional diesel engine-vapour compression APUs. The potential performance of a novel hybrid Stirling engine-adsorption chiller concept is investigated and benchmarked against the incumbent technology using a reduced-order model based on experimental data. Experimental results from a Stirling-adsorption system (SAS) prototype test rig are also presented which highlight system integration dynamics and overall performance. The adsorption chiller achieved an average COP of 0.42 ± 0.06 and 2.3 ± 0.1 kW_t of cooling capacity at the baseline test condition. The prototype SAS test rig demonstrates that there appear to be no major technology barriers remaining that would prevent adoption of the SAS concept in a next-generation APU. Such a system could offer a reduction of exhaust emissions, greenhouse gases (GHG), ozone-depleting substances, noise, low maintenance and the potential for fuel flexibility and higher reliability. Preliminary modelling results indicate that the proposed system could offer superior overall electrical and cooling efficiencies compared to incumbent APUs and demonstrate a payback period of 4.6 years.

Experimental study on transportation safety of package in side collision of heavy duty truck

International Nuclear Information System (INIS)

Suga, M.; Sasaki, T.

1989-01-01

The accidents in road transportation of package may be collision, fall and fire. It is necessary to examine all cases very carefully because collision might be caused by other vehicle. Collisions are classified into head-on collision, rear-end collision, side collision. A lot of experiments and analyses are reported on head-on collision, so the behavior of vehicle and package may be predicted without difficulty. Rear-end collisions bring about less impact and may be applied corresponding to the head-on collisions. About side collisions, few experiments or analyses are reported, and most of them are about passenger cars not about trucks. So it becomes important to study the transportation safety of package carried on a heavy duty truck when hit on the side by another truck similar in size

Single bank NOx adsorber for heavy duty diesel engines

NARCIS (Netherlands)

Genderen, M. van; Aken, M.G. van

2003-01-01

In a NOx adsorber programme the feasibility for applying this technology to heavy duty diesel engines was investigated. After modelling and simulations for realising best λ < 1 engine conditions a platform was build which was used to obtain good NOx adsorber regeneration settings in a number of

Robust cylinder pressure estimation in heavy-duty diesel engines

NARCIS (Netherlands)

Kulah, S.; Forrai, A.; Rentmeester, F.; Donkers, T.; Willems, F.P.T.

2017-01-01

The robustness of a new single-cylinder pressure sensor concept is experimentally demonstrated on a six-cylinder heavy-duty diesel engine. Using a single-cylinder pressure sensor and a crank angle sensor, this single-cylinder pressure sensor concept estimates the in-cylinder pressure traces in the

Battery Dimensioning and Life Cycle Costs Analysis for a Heavy-Duty Truck Considering the Requirements of Long-Haul Transportation

OpenAIRE

Mareev, Ivan; Becker, Jan Nicolas; Sauer, Dirk Uwe

2018-01-01

The use of heavy-duty battery electric trucks for long-haul transportation is challenging because of the required high energy amounts and thus the high capacity of traction batteries. Furthermore a high capacity battery implies high initial costs for the electric vehicle. This study investigates the required battery capacity for battery electric trucks considering the requirements of long-haul transportation in Germany and compares the life cycle costs of battery electric trucks and conventio...

Performance and emissions of a heavy duty diesel engine fuelled whit palm oil biodiesel and premium diesel

International Nuclear Information System (INIS)

Acevedo, Helmer; Mantilla, Juan

2011-01-01

Biodiesels are promoted as alternative fuels due their potential to reduce dependency on fossil fuels and carbon emissions. Research has been addressed in order to study the emissions of light duty vehicles. However, the particle matter and gaseous emissions emitted from heavy-duty diesel engines fueled with palm-biodiesel and premium diesel fuel have seldom been addressed. The objective of this study was to explore the performance and emission levels of a Cummins 4-stroke, 9.5 liter, 6-cylinder diesel engine with common rail fuel injection, and a cooled exhaust gas recirculation (EGR). The palm-biodiesel lowered maximum engine output by much as 10 %. The engine emissions data is compared to standards from 2004, and is determined to pass all standards for diesel fuel, but does not meet emissions standards for PM or NOx for palm-biodiesel.

On-road heavy-duty diesel particulate matter emissions modeled using chassis dynamometer data.

Science.gov (United States)

Kear, Tom; Niemeier, D A

2006-12-15

This study presents a model, derived from chassis dynamometer test data, for factors (operational correction factors, or OCFs) that correct (g/mi) heavy-duty diesel particle emission rates measured on standard test cycles for real-world conditions. Using a random effects mixed regression model with data from 531 tests of 34 heavy-duty vehicles from the Coordinating Research Council's E55/E59 research project, we specify a model with covariates that characterize high power transient driving, time spent idling, and average speed. Gram per mile particle emissions rates were negatively correlated with high power transient driving, average speed, and time idling. The new model is capable of predicting relative changes in g/mi on-road heavy-duty diesel particle emission rates for real-world driving conditions that are not reflected in the driving cycles used to test heavy-duty vehicles.

Emission Control Research to Enable Fuel Efficiency: Department of Energy Heavy Vehicle Technologies

International Nuclear Information System (INIS)

Gurpreet Singh; Ronald L. Graves; John M. Storey; William P. Partridge; John F. Thomas; Bernie M. Penetrante; Raymond M. Brusasco; Bernard T. Merritt; George E. Vogtlin; Christopher L. Aardahl; Craig F. Habeger; M.L. Balmer

2000-01-01

The Office of Heavy Vehicle Technologies supports research to enable high-efficiency diesel engines to meet future emissions regulations, thus clearing the way for their use in light trucks as well as continuing as the most efficient powerplant for freight-haulers. Compliance with Tier 2 rules and expected heavy duty engine standards will require effective exhaust emission controls (after-treatment) for diesels in these applications. DOE laboratories are working with industry to improve emission control technologies in projects ranging from application of new diagnostics for elucidating key mechanisms, to development and tests of prototype devices. This paper provides an overview of these R and D efforts, with examples of key findings and developments

Russia's black carbon emissions: focus on diesel sources

Directory of Open Access Journals (Sweden)

N. Kholod

2016-09-01

Full Text Available Black carbon (BC is a significant climate forcer with a particularly pronounced forcing effect in polar regions such as the Russian Arctic. Diesel combustion is a major global source of BC emissions, accounting for 25–30 % of all BC emissions. While the demand for diesel is growing in Russia, the country's diesel emissions are poorly understood. This paper presents a detailed inventory of Russian BC emissions from diesel sources. Drawing on a complete Russian vehicle registry with detailed information about vehicle types and emission standards, this paper analyzes BC emissions from diesel on-road vehicles. We use the COPERT emission model (COmputer Programme to calculate Emissions from Road Transport with Russia-specific emission factors for all types of on-road vehicles. On-road diesel vehicles emitted 21 Gg of BC in 2014: heavy-duty trucks account for 60 % of the on-road BC emissions, while cars represent only 5 % (light commercial vehicles and buses account for the remainder. Using Russian activity data and fuel-based emission factors, the paper also presents BC emissions from diesel locomotives and ships, off-road engines in industry, construction and agriculture, and generators. The study also factors in the role of superemitters in BC emissions from diesel on-road vehicles and off-road sources. The total emissions from diesel sources in Russia are estimated to be 49 Gg of BC and 17 Gg of organic carbon (OC in 2014. Off-road diesel sources emitted 58 % of all diesel BC in Russia.

Idling Reduction for Long-Haul Trucks: An Economic Comparison of On-Board and Wayside Technologies

Energy Technology Data Exchange (ETDEWEB)

Gaines, Linda [Argonne National Lab. (ANL), Argonne, IL (United States); Weikersheimer, Patricia [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-09-01

Reducing the idling of long-haul heavy-duty trucks has long been recognized as a particularly low-hanging fruit of fuel efficiency and emissions reduction. The displacement of about 10 hours of diesel idling every day, for most days of the year, for as many as a million long-haul trucks has very clear benefits. This report considers the costs and return on investment (ROI) for idling reduction (IR) equipment for both truck owners and electrified parking space (EPS) equipment owners. For the truck owners, the key variables examined are idling hours to be displaced (generally 1,000 to 2,000 hours per year) and the price of fuel ($0 to $5/gal). The ideal IR option would provide complete services in varied climates in any location and offer the best ROI on trucks that log many idling hours. For trucks that have fewer idling hours, options with a fixed cost per hour (i.e., EPS) might be most attractive if they were available to all, or even most, truck drivers. EPS, however, is particularly cost effective for trucks on prescribed routes with a need for regular, extended stops at terminals. (EPS is also called truck stop electrification, or TSE.) The analysis shows that all IR options save money when fuel costs more than $2/gal. For trucks requiring bunk heat, a simple heater (plug-in or diesel) is almost always the most costeffective way to provide heat, even if the truck is equipped with an auxiliary power unit (APU) or is parked at a single-system EPS location. For trucks requiring bunk air-conditioning, the use of single-system EPS is most cost effective for those logging fewer idling hours. Even for trucks with higher idling hours, the cost of EPS may be about the same as that for on-board air-conditioning. Clearly, trucks’ locations and seasonal factors—and the availability of EPS— are significant in the choice of “best fit” IR equipment for truck owners. This report also considers costs and payback for owners of EPS infrastructure. An industry that 5

Affordable Rankine Cycle Waste Heat Recovery for Heavy Duty Trucks

Energy Technology Data Exchange (ETDEWEB)

Subramanian, Swami Nathan [Eaton Corporation

2017-06-30

Nearly 30% of fuel energy is not utilized and wasted in the engine exhaust. Organic Rankine Cycle (ORC) based waste heat recovery (WHR) systems offer a promising approach on waste energy recovery and improving the efficiency of Heavy-Duty diesel engines. Major barriers in the ORC WHR system are the system cost and controversial waste heat recovery working fluids. More than 40% of the system cost is from the additional heat exchangers (recuperator, condenser and tail pipe boiler). The secondary working fluid loop designed in ORC system is either flammable or environmentally sensitive. The Eaton team investigated a novel approach to reduce the cost of implementing ORC based WHR systems to Heavy-Duty (HD) Diesel engines while utilizing safest working fluids. Affordable Rankine Cycle (ARC) concept aimed to define the next generation of waste energy recuperation with a cost optimized WHR system. ARC project used engine coolant as the working fluid. This approach reduced the need for a secondary working fluid circuit and subsequent complexity. A portion of the liquid phase engine coolant has been pressurized through a set of working fluid pumps and used to recover waste heat from the exhaust gas recirculation (EGR) and exhaust tail pipe exhaust energy. While absorbing heat, the mixture is partially vaporized but remains a wet binary mixture. The pressurized mixed-phase engine coolant mixture is then expanded through a fixed-volume ratio expander that is compatible with two-phase conditions. Heat rejection is accomplished through the engine radiator, avoiding the need for a separate condenser. The ARC system has been investigated for PACCAR’s MX-13 HD diesel engine.

Comparison of EGR-VTG control schemes for an EPA2010 heavy-duty diesel engine

NARCIS (Netherlands)

Criens, C.H.A.; Willems, F.P.T.; Steinbuch, M.

2011-01-01

Next generation heavy-duty diesel engines require tight air path control to meet upcoming emission legislation with minimal fuel consumption. This study concentrates on the emission control of a 13l, 360 kW EGR diesel engine, which is compliant with EPA2010 emission targets. Currently, an

Fuel composition impact on heavy duty diesel engine combustion & emissions

NARCIS (Netherlands)

Frijters, P.J.M.

2012-01-01

The Heavy Duty Diesel or compression ignition (CI) engine plays an important economical role in societies all over the world. Although it is a fuel efficient internal combustion engine design, CI engine emissions are an important contributor to global pollution. To further reduce engine emissions

Carbon and energy footprints of electric delivery trucks:a hybrid multi-regional input-output life cycle assessment

OpenAIRE

Zhao, Yang; Onat, Nuri Cihat; Küçükvar, Murat; Tatari, Ömer

2016-01-01

Due to frequent stop-and-go operation and long idling periods when driving in congested urban areas, the electrification of commercial delivery trucks has become an interesting topic nationwide. In this study, environmental impacts of various alternative delivery trucks including battery electric, diesel, diesel-electric hybrid, and compressed natural gas trucks are analyzed. A novel life cycle assessment method, an environmentally-extended multi-region input-output analysis, is utilized to c...

Model based control for waste heat recovery rankine cycle system in heavy duty trucks

OpenAIRE

Grelet, Vincent; Dufour, Pascal; Nadri, Madiha; Lemort, Vincent; Reiche, Thomas

2015-01-01

Driven by future emissions legislations and increase in fuel prices engine, gas heat recovering has recently attracted a lot of interest. In the past few years, a high number of studies have shown the interest of energy recovery Rankine based systems for heavy duty trucks engine compounding. Recent studies have brought a significant potential for such a system in a Heavy Duty (HD) vehicle, which can lead to a decrease in fuel consumption of about 5% [Wang et al. (2011)] and reduce engine emis...

Effects of ethanol-diesel fuel blends on the performance and exhaust emissions of heavy duty DI diesel engine

International Nuclear Information System (INIS)

Rakopoulos, D.C.; Rakopoulos, C.D.; Kakaras, E.C.; Giakoumis, E.G.

2008-01-01

An experimental investigation is conducted to evaluate the effects of using blends of ethanol with conventional diesel fuel, with 5% and 10% (by vol.) ethanol, on the performance and exhaust emissions of a fully instrumented, six-cylinder, turbocharged and after-cooled, heavy duty, direct injection (DI), Mercedes-Benz engine, installed at the authors' laboratory, which is used to power the mini-bus diesel engines of the Athens Urban Transport Organization sub-fleet with a view to using bio-ethanol produced from Greek feedstock. The tests are conducted using each of the above fuel blends, with the engine working at two speeds and three loads. Fuel consumption, exhaust smokiness and exhaust regulated gas emissions such as nitrogen oxides, carbon monoxide and total unburned hydrocarbons are measured. The differences in the measured performance and exhaust emissions of the two ethanol-diesel fuel blends from the baseline operation of the engine, i.e. when working with neat diesel fuel, are determined and compared. Theoretical aspects of diesel engine combustion combined with the widely differing physical and chemical properties of the ethanol against those for the diesel fuel, are used to aid the correct interpretation of the observed engine behavior

Sulfur driven nucleation mode formation in diesel exhaust under transient driving conditions.

Science.gov (United States)

Karjalainen, Panu; Rönkkö, Topi; Pirjola, Liisa; Heikkilä, Juha; Happonen, Matti; Arnold, Frank; Rothe, Dieter; Bielaczyc, Piotr; Keskinen, Jorma

2014-02-18

Sulfur driven diesel exhaust nucleation particle formation processes were studied in an aerosol laboratory, on engine dynamometers, and on the road. All test engines were equipped with a combination of a diesel oxidation catalyst (DOC) and a partial diesel particulate filter (pDPF). At steady operating conditions, the formation of semivolatile nucleation particles directly depended on SO2 conversion in the catalyst. The nucleation particle emission was most significant after a rapid increase in engine load and exhaust gas temperature. Results indicate that the nucleation particle formation at transient driving conditions does not require compounds such as hydrocarbons or sulfated hydrocarbons, however, it cannot be explained only by the nucleation of sulfuric acid. A real-world exhaust study with a heavy duty diesel truck showed that the nucleation particle formation occurs even with ultralow sulfur diesel fuel, even at downhill driving conditions, and that nucleation particles can contribute 60% of total particle number emissions. In general, due to sulfur storage and release within the exhaust aftertreatment systems and transients in driving, emissions of nucleation particles can even be the dominant part of modern diesel vehicle exhaust particulate number emissions.

On particulate characterization in a heavy-duty diesel engine by time-resolved laser-induced incandescence

NARCIS (Netherlands)

Bougie, H.J.T.

2007-01-01

This dissertation describes the results of soot measurements acquired in the combustion chamber of an optically accessible heavy-duty Diesel engine. The Diesel engine is the most efficient internal combustion engine. Pollutant emissions from the engine, such as soot and NOx, however, form a

Waste heat recovery from adiabatic diesel engines by exhaust-driven Brayton cycles

Science.gov (United States)

Khalifa, H. E.

1983-01-01

An evaluation of Bryton Bottoming Systems (BBS) as waste heat recovery devices for future adiabatic diesel engines in heavy duty trucks is presented. Parametric studies were performed to evaluate the influence of external and internal design parameters on BBS performance. Conceptual design and trade-off studies were undertaken to estimate the optimum configuration, size, and cost of major hardware components. The potential annual fuel savings of long-haul trucks equipped with BBS were estimated. The addition of a BBS to a turbocharged, nonaftercooled adiabatic engine would improve fuel economy by as much as 12%. In comparison with an aftercooled, turbocompound engine, the BBS-equipped turbocharged engine would offer a 4.4% fuel economy advantage. If installed in tandem with an aftercooled turbocompound engine, the BBS could effect a 7.2% fuel economy improvement. The cost of a mass-produced 38 Bhp BBS is estimated at about $6460 or 170/Bhp. Technical and economic barriers that hinder the commercial introduction of bottoming systems were identified. Related studies in the area of waste heat recovery from adiabatic diesel engines and NASA-CR-168255 (Steam Rankine) and CR-168256 (Organic Rankine).

Modeling Heavy/Medium-Duty Fuel Consumption Based on Drive Cycle Properties

Energy Technology Data Exchange (ETDEWEB)

Wang, Lijuan; Duran, Adam; Gonder, Jeffrey; Kelly, Kenneth

2015-10-13

This paper presents multiple methods for predicting heavy/medium-duty vehicle fuel consumption based on driving cycle information. A polynomial model, a black box artificial neural net model, a polynomial neural network model, and a multivariate adaptive regression splines (MARS) model were developed and verified using data collected from chassis testing performed on a parcel delivery diesel truck operating over the Heavy Heavy-Duty Diesel Truck (HHDDT), City Suburban Heavy Vehicle Cycle (CSHVC), New York Composite Cycle (NYCC), and hydraulic hybrid vehicle (HHV) drive cycles. Each model was trained using one of four drive cycles as a training cycle and the other three as testing cycles. By comparing the training and testing results, a representative training cycle was chosen and used to further tune each method. HHDDT as the training cycle gave the best predictive results, because HHDDT contains a variety of drive characteristics, such as high speed, acceleration, idling, and deceleration. Among the four model approaches, MARS gave the best predictive performance, with an average absolute percent error of -1.84% over the four chassis dynamometer drive cycles. To further evaluate the accuracy of the predictive models, the approaches were first applied to real-world data. MARS outperformed the other three approaches, providing an average absolute percent error of -2.2% of four real-world road segments. The MARS model performance was then compared to HHDDT, CSHVC, NYCC, and HHV drive cycles with the performance from Future Automotive System Technology Simulator (FASTSim). The results indicated that the MARS method achieved a comparative predictive performance with FASTSim.

Heavy-duty diesel engine NO{sub x} reduction with nitrogen-enriched combustion air. Final CRADA report.

Energy Technology Data Exchange (ETDEWEB)

McConnell, S.; Energy Systems

2010-07-28

The concept of engine emissions control by modifying intake combustion gas composition from that of ambient air using gas separation membranes has been developed during several programs undertaken at Argonne. These have led to the current program which is targeted at heavy-duty diesel truck engines. The specific objective is reduction of NO{sub x} emissions by the target engine to meet anticipated 2007 standards while extracting a maximum of 5 percent power loss and allowing implementation within commercial constraints of size, weight, and cost. This report includes a brief review of related past programs, describes work completed to date during the current program, and presents interim conclusions. Following a work schedule adjustment in August 2002 to accommodate problems in module procurement and data analysis, activities are now on schedule and planned work is expected to be completed in September, 2004. Currently, we believe that the stated program requirements for the target engine can be met, based upon extrapolation of the work completed. Planned project work is designed to experimentally confirm these projections and result in a specification for a module package that will meet program objectives.

Carbonyl compound emissions from a heavy-duty diesel engine fueled with diesel fuel and ethanol-diesel blend.

Science.gov (United States)

Song, Chonglin; Zhao, Zhuang; Lv, Gang; Song, Jinou; Liu, Lidong; Zhao, Ruifen

2010-05-01

This paper presents an investigation of the carbonyl emissions from a direct injection heavy-duty diesel engine fueled with pure diesel fuel (DF) and blended fuel containing 15% by volume of ethanol (E/DF). The tests have been conducted under steady-state operating conditions at 1200, 1800, 2600 rpm and idle speed. The experimental results show that acetaldehyde is the most predominant carbonyl, followed by formaldehyde, acrolein, acetone, propionaldehyde and crotonaldehyde, produced from both fuels. The emission factors of total carbonyls vary in the range 13.8-295.9 mg(kWh)(-1) for DF and 17.8-380.2mg(kWh)(-1) for E/DF, respectively. The introduction of ethanol into diesel fuel results in a decrease in acrolein emissions, while the other carbonyls show general increases: at low engine speed (1200 rpm), 0-55% for formaldehyde, 4-44% for acetaldehyde, 38-224% for acetone, and 5-52% for crotonaldehyde; at medium engine speed (1800 rpm), 106-413% for formaldehyde, 4-143% for acetaldehyde, 74-113% for acetone, 114-1216% for propionaldehyde, and 15-163% for crotonaldehyde; at high engine speed (2600 rpm), 36-431% for formaldehyde, 18-61% for acetaldehyde, 22-241% for acetone, and 6-61% for propionaldehyde. A gradual reduction in the brake specific emissions of each carbonyl compound from both fuels is observed with increase in engine load. Among three levels of engine speed employed, both DF and E/DF emit most CBC emissions at high engine speed. On the whole, the presence of ethanol in diesel fuel leads to an increase in aldehyde emissions. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Exhaust emissions evaluation of Colombian commercial diesel fuels

International Nuclear Information System (INIS)

Torres, Jaime; Bello, Arcesio; Sarmiento, Jose; Rostkowski, Jacek; Brady, Jeremy

2003-01-01

Ecopetrol, based on the results obtained in the study, The effect of diesel properties on the emissions of particulate matter (Bello et al 2000), reformulated the diesel fuel distributed in Bogota, becoming it lighter and with lower sulfur content. In order to evaluate the environmental benefits that the reformulation of diesel fuel generate in Bogota, Instituto Colombiano del Petroleo (ICP), with the assistance of emissions research and measurement division (ERMD) from environment Canada, arranged a research project to determine the changes in CO, THC, NO x , CO 2 and particulate matter emissions. The research program was developed in two steps. First one, developed in Bogota, involved a fleet test with 15 public service buses that normally operate in Bogota's savannah, using a portable emissions sampling technology developed for ERMD (DOES2) and following a representative transient driving cycle. Second step, carried out in ERMD's Heavy-Duty engine emissions laboratory in Ottawa, tested a 1995 caterpillar 3406E 324/5 KW (435 HP) diesel truck engine on the same samples of Colombian diesel fuels used in the fleet tests performed in Bogota, baselining the tests with a Canadian commercial low sulfur diesel fuel. The two commercial Colombian diesel fuels used had the following properties: High Sulfur Diesel (HSD), with 3000 ppm (0,3 wt %) of sulfur and a final boiling point (FBP) of 633 K and the new reformulated diesel fuel, with 1000 ppm (0,1 wt %) of sulfur and FBP of 613 K, which is currently been distributed in Bogota. Fleet test show small reduction on CO, THC and TPM, and small increments on CO 2 and NO x but with not statistically significant results, while engine testing shows a strong reduction of 40/8% in TPM when you use the new reformulated diesel fuel (0,1 wt % of sulfur) instead of high sulfur diesel

South Coast Air Quality Management District Truck Testing | Transportation

Science.gov (United States)

Research | NREL South Coast Air Quality Management District Truck Evaluation South Coast Air Quality Management District Truck Evaluation Photo of heavy-duty truck cab. Electric drayage truck Cargo Transportation project, conducted in partnership with the South Coast Air Quality Management

The open-pit truck dispatching method based on the completion of production target and the truck flow saturation

Energy Technology Data Exchange (ETDEWEB)

Xing, J.; Sun, X. [Northeastern University, Shenyang (China)

2007-05-15

To address current problems in the 'modular dispatch' dynamic programming system widely used in open-pit truck real-time dispatching, two concepts for meeting production targets and truck flow saturation were proposed. Using truck flow programming and taking into account stochastic factors and transportation distance, truck real-time dispatching was optimised. The method is applicable to both shovel-truck match and mismatching and also to empty and heavy truck dispatching. In an open-pit mine the production efficiency could be increased by between 8% and 18%. 6 refs.

Numerical Evaluation ofThe Performance ofA Compression Ignition Cng Engine For Heavy DutyTrucksWithAn Optimum Speed PowerTurbine

Directory of Open Access Journals (Sweden)

Alberto A. Boretti

2011-10-01

Full Text Available The turbocharged direct injection lean burn Diesel engine is the most efficient engine now in production for transport applications. CNG is an alternative fuel with a better carbon to hydrogen ratio therefore permitting reduced carbon dioxide emissions. It is injected in gaseous form for a much cleaner combustion almost cancelling some of the emissions of the Diesel and it permits a much better energy security within Australia. The paper discusses the best options currently available to convert Diesel engine platforms to CNG, with particular emphasis to the use of these CNG engines within Australia where the refuelling network is scarce. This option is determined in the dual fuel operation with a double injector design that couples a second CNG injector to the Diesel injector. This configuration permits the operation Diesel only or Diesel pilot and CNG main depending on the availability of refuelling stations where the vehicle operates. Results of engine performance simulations are performed for a straight six cylinder 13 litres truck engine with a novel power turbine connected to the crankshaft through a constant variable transmission that may be by-passed when non helpful to increase the fuel economy of the vehicle or when damaging the performances of the after treatment system.

Opportunities for Low Cost Titanium in Reduced Fuel Consumption, Improved Emissions, and Enhanced Durability Heavy Duty Vehicles

Energy Technology Data Exchange (ETDEWEB)

Kraft, E.H.

2002-07-22

The purpose of this study was to determine which components of heavy-duty highway vehicles are candidates for the substitution of titanium materials for current materials if the cost of those Ti components is very significantly reduced from current levels. The processes which could be used to produce those low cost components were also investigated. Heavy-duty highway vehicles are defined as all trucks and busses included in Classes 2C through 8. These include heavy pickups and vans above 8,500 lbs. GVWR, through highway tractor trailers. Class 8 is characterized as being a very cyclic market, with ''normal'' year volume, such as in 2000, of approximately 240,000 new vehicles. Classes 3-7 are less cyclic, with ''normal'' i.e., year 2000, volume totaling approximately 325,000 new vehicles. Classes 3-8 are powered about 88.5% by diesel engines, and Class 2C at very roughly 83% diesel. The engine portion of the study therefore focused on diesels. Vehicle production volumes were used in estimates of the market size for candidate components.

NOx reduction in diesel fuel flames by additions of water and CO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Li, S.C. [Univ. of California, San Diego, La Jolla, CA (United States)

1997-12-31

Natural gas has the highest heating value per unit mass (50.1 MJ/kg, LHV) of any of the hydrocarbon fuels (e.g., butane, liquid diesel fuel, gasoline, etc.). Since it has the lowest carbon content per unit mass, combustion of natural gas produces much less carbon dioxide, soot particles, and oxide of nitrogen than combustion of liquid diesel fuel. In view of anticipated strengthening of regulations on pollutant emissions from diesel engines, alternative fuels, such as compressed natural gas (CNG) and liquefied natural gas (LNG) have been experimentally introduced to replace the traditional diesel fuels in heavy-duty trucks, transit buses, off-road vehicles, locomotives, and stationary engines. To help in applying natural gas in Diesel engines and increasing combustion efficiency, the emphasis of the present paper is placed on the detailed flame chemistry of methane-air combustion. The present work is the continued effort in finding better methods to reduce NO{sub x}. The goal is to identify a reliable chemical reaction mechanism for natural gas in both premixed and diffusion flames and to establish a systematic reduced mechanism which may be useful for large-scale numerical modeling of combustion behavior in natural gas engines.

Cleaning the Diesel Engine Emissions

DEFF Research Database (Denmark)

Christensen, Thomas Budde

This paper examines how technologies for cleaning of diesel emission from road vehicles can be supported by facilitating a technology push in the Danish automotive emission control industry. The European commission is at present preparing legislation for the euro 5 emission standard (to be enforced...... in 2010). The standard is expected to include an 80% reduction of the maximum particulate emissions from diesel cars. The fulfillment of this requirement entails development and production of particulate filters for diesel cars and trucks. Theoretically the paper suggests a rethinking of public industry...

Prediction of major pollutants emission in direct injection dual-fuel diesel and natural-gas engines

International Nuclear Information System (INIS)

Pirouzpanah, V.; Kashani, B.O.

2000-01-01

The dual-fuel diesel engine is a conventional diesel engine in which much of the energy released, hence power, comes from the combustion of gaseous fuel such as natural gas. The exhaust emission characteristics of the dual-fuel diesel engine needs further refinements, particularly in terms of reduction of Unburnt Hydrocarbons and Carbon Monoxide (CO) emission, because the concentration of these pollutants are higher than that of the baseline diesel engine. Furthermore, the combustion process in a typical dual-fuel diesel engine tends to be complex, showing combination of the problems encountered both in diesel and spark ignition engines. In this work, a computer code has been modified for simulation of dual-fuel diesel engine combustion process. This model simulates dual-fuel diesel engine combustion by using a Multi-Zone Combustion Model for diesel pilot jet combustion and a conventional spark ignition combustion model for modelling of combustion of premixed gas/air charge. Also, in this model, there are four submodels for prediction of major emission pollutants such as: Unburnt Hydrocarbons, No, Co and soot which are emitted from dual-fuel diesel engine. For prediction of formation and oxidation rates of pollutants, relevant s conventional kinetically-controlled mechanisms and mass balances are used. the model has been verified by experimental data obtained from a heavy-duty truck and bus diesel engines. The comparison shows that, there exist good agreements between the experimental and predicted results from the dual-fuel diesel engine

Direct injection of a diesel-butane blend in a heavy duty engine

NARCIS (Netherlands)

Leermakers, C.A.J.; van den Berge, B.; Luijten, C.C.M.; Somers, L.M.T.; Jaasma, S.A.M.; Goey, de L.P.H.

2011-01-01

LPG (Liquefied Petroleum Gas) has for long been used in passenger cars. Presently, LPG sup-ply systems have also attracted considerable at-tention for heavy duty use. LPG can be applied in these engines combining port fuel injected LPG with a direct injection of diesel. These engines equipped with a

Papers on vehicle size : cars and trucks

Science.gov (United States)

1988-06-01

The four papers in this volume describe analyses of car size : trends and truck occupant injuries and fatalities. All four were : written between June 1985 and December 1987. The topics : addressed include where heavy truck accidents occur, injury an...

Experimental Measurement of the Flow Field of Heavy Trucks

Energy Technology Data Exchange (ETDEWEB)

Fred Browand; Charles Radovich

2005-05-31

Flat flaps that enclose the trailer base on the sides and top are known to reduce truck drag and reduce fuel consumption. Such flapped-truck geometries have been studied in laboratory wind tunnels and in field tests. A recent review of wind tunnel data for a variety of truck geometries and flow Reynolds numbers show roughly similar values of peak drag reduction, but differ in the determination of the optimum flap angle. Optimum angles lie in the range 12 degrees-20 degrees, and may be sensitive to Reynolds number and truck geometry. The present field test is undertaken to provide additional estimates of the magnitude of the savings to be expected on a typical truck for five flap angles 10, 13, 16, 19, and 22 degrees. The flaps are constructed from a fiberglass-epoxy-matrix material and are one-quarter of the base width in length (about 61 cm, or 2 feet). They are attached along the rear door hinge lines on either side of the trailer, so that no gap appears at the joint between the flap and the side of the trailer The flap angle is adjusted by means of two aluminum supports. The present test is performed on the NASA Crows Landing Flight Facility at the northern end of the San Joaquin valley in California. The main runway is approximately 2400 meters in length, and is aligned approximately in a north-south direction The test procedure is to make a series of runs starting at either end of the runway. All runs are initiated under computer control to accelerate the truck to a target speed of 60 mph (96 6 km/hr), to proceed at the target speed for a fixed distance, and to decelerate at the far end of the runway. During a run, the broadcast fuel rate, the engine rpm, forward speed, elapsed time--as well as several other parameters (10 in all)--are digitized at a rate of 100 digitizations per second. Various flapped-conditions are interspersed with the ''no flaps'' control, and are sequenced in a different order on different days. Approximately 310 runs

Trucks involved in fatal accidents codebook 2008.

Science.gov (United States)

2011-01-01

This report provides documentation for UMTRIs file of Trucks Involved in Fatal Accidents : (TIFA), 2008, including distributions of the code values for each variable in the file. The 2008 : TIFA file is a census of all medium and heavy trucks invo...

FedEx Gasoline Hybrid Electric Delivery Truck Evaluation: 6-Month Interim Report

Energy Technology Data Exchange (ETDEWEB)

Barnitt, R.

2010-05-01

This interim report presents partial (six months) results for a technology evaluation of gasoline hybrid electric parcel delivery trucks operated by FedEx in and around Los Angeles, CA. A 12 month in-use technology evaluation comparing in-use fuel economy and maintenance costs of GHEVs and comparative diesel parcel delivery trucks was started in April 2009. Comparison data was collected and analyzed for in-use fuel economy and fuel costs, maintenance costs, total operating costs, and vehicle uptime. In addition, this interim report presents results of parcel delivery drive cycle collection and analysis activities as well as emissions and fuel economy results of chassis dynamometer testing of a gHEV and a comparative diesel truck at the National Renewable Energy Laboratory's (NREL) ReFUEL laboratory. A final report will be issued when 12 months of in-use data have been collected and analyzed.

Vehicle to Grid regulation services of electric delivery trucks: Economic and environmental benefit analysis

International Nuclear Information System (INIS)

Zhao, Yang; Noori, Mehdi; Tatari, Omer

2016-01-01

Highlights: • Potential net present revenues of electric truck based V2G regulation services are investigated. • GHG emission mitigation of V2G regulation services provided by electric trucks are quantified. • The total cost of ownership and the life-cycle GHG emissions of electric trucks are also analyzed. • V2G regulation services for electric trucks could yield considerable revenues and GHG emission savings. - Abstract: Concerns regarding the fuel costs and climate change impacts associated with petroleum combustion are among the main driving factors for the adoption of electric vehicles. Future commercial delivery truck fleets may include Battery Electric Vehicles (BEVs) and Extended Range Electric Vehicles (EREVs); in addition to savings on fuel and maintenance costs, the introduction of these grid accessible electric vehicles will also provide fleet owners with possible Vehicle to Grid (V2G) opportunities. This study investigates the potential net present revenues and greenhouse gas (GHG) emission mitigation of V2G regulation services provided by electric trucks in a typical fleet. The total cost of ownership and the life-cycle GHG emissions of electric trucks are also analyzed and compared to those of traditional diesel trucks. To account for uncertainties, possible ranges for key parameters are considered instead of only considering fixed single data values for each parameter. The results of this research indicate that providing V2G regulation services for electric trucks could yield considerable additional revenues ($20,000–50,000) and significant GHG emission savings (approximately 300 ton CO_2) compared to conventional diesel trucks.

Design and Manufacture of Heavy Truck Braking Spray Device Based on PLCS7-200

Directory of Open Access Journals (Sweden)

Zuojun SONG

2014-12-01

Full Text Available The braking effect is decreased rapidly in heavy truck when the temperature of braking friction plate reaches a certain value. The device measures the temperature of friction plate adopting a thermistor temperature sensor, put the temperature value into the PLC controller, compared with the selected temperature value, and the temperature of friction plate is controlled through controlling the open and close of electromagnetic valve of water supply. It has high stability, strong anti- interference ability and easy maintenance etc.

Fuel Economy Improvement Potential of a Heavy Duty Truck using V2x Communication

Energy Technology Data Exchange (ETDEWEB)

LaClair, Tim J [ORNL; Verma, Rajeev [Eaton Corporation; Norris, Sarah [Eaton Corporation; Cochran, Robert [Eaton Corporation

2014-01-01

In this paper, we introduce an intelligent driver assistance system to reduce fuel consumption in heavy duty vehicles irrespective of the driving style of the driver. We specifically study the potential of V2I and V2V communications to reduce fuel consumption in heavy duty trucks. Most ITS communications today are oriented towards vehicle safety, with communications strategies and hardware that tend to focus on low latency. This has resulted in technologies emerging with a relatively limited range for the communications. For fuel economy, it is expected that most benefits will be derived with greater communications distances, at the scale of many hundred meters or several kilometers, due to the large inertia of heavy duty vehicles. It may therefore be necessary to employ different communications strategies for ITS applications aimed at fuel economy and other environmental benefits than what is used for safety applications in order to achieve the greatest benefits.

Quantitative laser-induced fluorescence measurements of nitric oxide in a heavy-duty Diesel engine

NARCIS (Netherlands)

Verbiezen, K.; Klein-Douwel, R. J. H.; van Viet, A. P.; Donkerbroek, A. J.; Meerts, W. L.; Dam, N. J.; ter Meulen, J. J.

2007-01-01

We present quantitative, in-cylinder, UV-laser-induced fluorescence measurements of nitric oxide in a heavy-duty Diesel engine. Processing of the raw fluorescence signals includes a detailed correction, based on additional measurements, for the effect of laser beam and fluorescence attenuation, and

Computer simulation of the heavy-duty turbo-compounded diesel cycle for studies of engine efficiency and performance

Science.gov (United States)

Assanis, D. N.; Ekchian, J. A.; Heywood, J. B.; Replogle, K. K.

1984-01-01

Reductions in heat loss at appropriate points in the diesel engine which result in substantially increased exhaust enthalpy were shown. The concepts for this increased enthalpy are the turbocharged, turbocompounded diesel engine cycle. A computer simulation of the heavy duty turbocharged turbo-compounded diesel engine system was undertaken. This allows the definition of the tradeoffs which are associated with the introduction of ceramic materials in various parts of the total engine system, and the study of system optimization. The basic assumptions and the mathematical relationships used in the simulation of the model engine are described.

Particulate emissions from road transportation (gasoline and diesel). Chemical and granulometric characteristics; relative contribution; Emissions particulaires par les transports routiers (essence et diesel) caracteristiques chimiques et granulometriques contribution relative

Energy Technology Data Exchange (ETDEWEB)

Belot, G. [PSA-Peugiot-Citroen, 92 - La Garenne-Colombes (France)

1996-12-31

The formation process and chemical composition of diesel, leaded and lead-free gasoline combustion particulates are presented, and the effects of engine technology, post-treatments (oxidative catalysis), automobile speed and fuel type (more especially diesel type), on the granulometry of gasoline and diesel automotive particulates are studied. The emission contributions from the various diesel vehicle types (automobiles, trucks, buses), gasoline and diesel automobiles and other natural and anthropogenic particulate sources, are presented and compared

Crash problem definition and safety benefits methodology for stability control for single-unit medium and heavy trucks and large-platform buses

Science.gov (United States)

2009-10-01

This report presents the findings of a comprehensive engineering analysis of electronic stability control (ESC) and roll stability control (RSC) systems for single-unit medium and heavy trucks and large-platform buses. This report details the applica...

40 CFR 86.085-2 - Definitions.

Science.gov (United States)

2010-07-01

... 1977 and Later Model Year New Light-Duty Vehicles, Light-Duty Trucks and Heavy-Duty Engines, and for... standard. PRODLDT represents the manufacturer's total diesel light-duty truck production for those engine... special purpose vehicles such as small dump trucks, and trash compactor trucks. Typical applications would...

Retrofit SCR system for NOx control from heavy-duty mining equipment

International Nuclear Information System (INIS)

Mannan, M.A.

2009-01-01

Diesel engines are used extensively in the mining industry and offer many advantages. However, particulate matter (PM) emissions and nitrogen oxide emissions (NOx) are among its disadvantages. A significant concern related to PM and NOx in an underground mine involves the use of diesel exhaust after treatment systems such as diesel particulate filters and selective catalytic reduction (SCR). This presentation discussed NOx and PM control and provided a description of an SCR system and examples of SCR retrofits. Options for NOx control were discussed and a case study involving the installation of an SCR retrofit system in an underground mine operated by Sifto Salt was also presented. The purpose of the case study was to identify cost effective retrofit solutions to lower nitrogen dioxide emissions from heavy-duty trucks operating in underground mines. The case study illustrated and presented the candidate vehicle, baseline emissions, a BlueMax SCR retrofit solution, and BlueMax installation. 1 tab., 6 figs.

40 CFR 86.1102-87 - Definitions.

Science.gov (United States)

2010-07-01

..., governed speed, injector size, engine calibration, or other parameters which may be designated by the... for Gasoline-Fueled and Diesel Heavy-Duty Engines and Heavy-Duty Vehicles, Including Light-Duty Trucks...-, diesel-, and methanol-fueled), vehicle usage, engine horsepower or additional criteria that the...

Greenhouse Gas and Noxious Emissions from Dual Fuel Diesel and Natural Gas Heavy Goods Vehicles.

Science.gov (United States)

Stettler, Marc E J; Midgley, William J B; Swanson, Jacob J; Cebon, David; Boies, Adam M

2016-02-16

Dual fuel diesel and natural gas heavy goods vehicles (HGVs) operate on a combination of the two fuels simultaneously. By substituting diesel for natural gas, vehicle operators can benefit from reduced fuel costs and as natural gas has a lower CO2 intensity compared to diesel, dual fuel HGVs have the potential to reduce greenhouse gas (GHG) emissions from the freight sector. In this study, energy consumption, greenhouse gas and noxious emissions for five after-market dual fuel configurations of two vehicle platforms are compared relative to their diesel-only baseline values over transient and steady state testing. Over a transient cycle, CO2 emissions are reduced by up to 9%; however, methane (CH4) emissions due to incomplete combustion lead to CO2e emissions that are 50-127% higher than the equivalent diesel vehicle. Oxidation catalysts evaluated on the vehicles at steady state reduced CH4 emissions by at most 15% at exhaust gas temperatures representative of transient conditions. This study highlights that control of CH4 emissions and improved control of in-cylinder CH4 combustion are required to reduce total GHG emissions of dual fuel HGVs relative to diesel vehicles.

Regulated and unregulated emissions from modern 2010 emissions-compliant heavy-duty on-highway diesel engines

Science.gov (United States)

Khalek, Imad A.; Blanks, Matthew G.; Merritt, Patrick M.; Zielinska, Barbara

2015-01-01

The U.S. Environmental Protection Agency (EPA) established strict regulations for highway diesel engine exhaust emissions of particulate matter (PM) and nitrogen oxides (NOx) to aid in meeting the National Ambient Air Quality Standards. The emission standards were phased in with stringent standards for 2007 model year (MY) heavy-duty engines (HDEs), and even more stringent NOX standards for 2010 and later model years. The Health Effects Institute, in cooperation with the Coordinating Research Council, funded by government and the private sector, designed and conducted a research program, the Advanced Collaborative Emission Study (ACES), with multiple objectives, including detailed characterization of the emissions from both 2007- and 2010-compliant engines. The results from emission testing of 2007-compliant engines have already been reported in a previous publication. This paper reports the emissions testing results for three heavy-duty 2010-compliant engines intended for on-highway use. These engines were equipped with an exhaust diesel oxidation catalyst (DOC), high-efficiency catalyzed diesel particle filter (DPF), urea-based selective catalytic reduction catalyst (SCR), and ammonia slip catalyst (AMOX), and were fueled with ultra-low-sulfur diesel fuel (~6.5 ppm sulfur). Average regulated and unregulated emissions of more than 780 chemical species were characterized in engine exhaust under transient engine operation using the Federal Test Procedure cycle and a 16-hr duty cycle representing a wide dynamic range of real-world engine operation. The 2010 engines’ regulated emissions of PM, NOX, nonmethane hydrocarbons, and carbon monoxide were all well below the EPA 2010 emission standards. Moreover, the unregulated emissions of polycyclic aromatic hydrocarbons (PAHs), nitroPAHs, hopanes and steranes, alcohols and organic acids, alkanes, carbonyls, dioxins and furans, inorganic ions, metals and elements, elemental carbon, and particle number were substantially

Thermodynamic analysis of a Rankine cycle applied on a diesel truck engine using steam and organic medium

International Nuclear Information System (INIS)

Katsanos, C.O.; Hountalas, D.T.; Pariotis, E.G.

2012-01-01

Highlights: ► ORC improves bsfc from 10.7% to 8.4% as engine load increases from 25% to 100%. ► Increasing ORC high pressure increases thermodynamic efficiency and power output. ► Operating at high pressure the ORC is favorable for the engine cooling system. ► The low temperature values of the ORC favors heat extraction from the EGR gas. ► The impact of the exhaust gas heat exchanger on engine backpressure is limited. - Abstract: A theoretical study is conducted to investigate the potential improvement of the overall efficiency of a heavy-duty truck diesel engine equipped with a Rankine bottoming cycle for recovering heat from the exhaust gas. To this scope, a newly developed thermodynamic simulation model has been used, considering two different working media: water and the refrigerant R245ca. As revealed from the analysis, due to the variation of exhaust gas temperature with engine load it is necessary to modify the Rankine cycle parameters i.e. high pressure and superheated vapor temperature. For this reason, a new calculation procedure is applied for the estimation of the optimum Rankine cycle parameters at each operating condition. The calculation algorithm is conducted by taking certain design criteria into account, such as the exhaust gas heat exchanger size and its pinch point requirement. From the comparative evaluation between the two working media examined, using the optimum configuration of the cycle for each operating condition, it has been revealed that the brake specific fuel consumption improvement ranges from 10.2% (at 25% engine load) to 8.5% (at 100% engine load) for R245ca and 6.1% (at 25% engine load) to 7.5% (at 100% engine load) for water.

Heavy-Duty Low-Temperature and Diesel Combustion & Heavy-Duty Combustion Modeling

Energy Technology Data Exchange (ETDEWEB)

Musculus, Mark P. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

2017-11-01

Regulatory drivers and market demands for lower pollutant emissions, lower carbon dioxide emissions, and lower fuel consumption motivate the development of clean and fuel-efficient engine operating strategies. Most current production engines use a combination of both in-cylinder and exhaust emissions-control strategies to achieve these goals. The emissions and efficiency performance of in-cylinder strategies depend strongly on flow and mixing processes associated with fuel injection. Various diesel engine manufacturers have adopted close-coupled post-injection combustion strategies to both reduce pollutant emissions and to increase engine efficiency for heavy-duty applications, as well as for light- and medium-duty applications. Close-coupled post-injections are typically short injections that follow a larger main injection in the same cycle after a short dwell, such that the energy conversion efficiency of the post-injection is typical of diesel combustion. Of the various post-injection schedules that have been reported in the literature, effects on exhaust soot vary by roughly an order of magnitude in either direction of increasing or decreasing emissions relative to single injections (O’Connor et al., 2015). While several hypotheses have been offered in the literature to help explain these observations, no clear consensus has been established. For new engines to take full advantage of the benefits that post-injections can offer, the in-cylinder mechanisms that affect emissions and efficiency must be identified and described to provide guidance for engine design.

Modeling and control of a parallel waste heat recovery system for Euro-VI heavy-duty diesel engines

NARCIS (Netherlands)

Feru, E.; Willems, F.P.T.; Jager, de A.G.; Steinbuch, M.

2014-01-01

This paper presents the modeling and control of a waste heat recovery systemfor a Euro-VI heavy-duty truck engine. The considered waste heat recovery system consists of two parallel evaporators with expander and pumps mechanically coupled to the engine crankshaft. Compared to previous work, the

Modeling and Control of a Parallel Waste Heat Recovery System for Euro-VI Heavy-Duty Diesel Engines

NARCIS (Netherlands)

Feru, E.; Willems, F.P.T.; Jager, B. de; Steinbuch, M.

2014-01-01

This paper presents the modeling and control of a waste heat recovery system for a Euro-VI heavy-duty truck engine. The considered waste heat recovery system consists of two parallel evaporators with expander and pumps mechanically coupled to the engine crankshaft. Compared to previous work, the

Development of the New Light-Duty Hybrid Truck

OpenAIRE

Yamaguchi, Koichi

2008-01-01

Hino Motors, Ltd., developed the new light-duty hybrid truck whose traction motor, inverter, and traction battery were completely redesigned for maximizing output and efficiency. It also succeeds in balancing low fuel economy and low exhaust emissions by utilizing a combination of a new hybrid system control with a specially developed diesel engine.

Quantitative Effects of Vehicle Parameters on Fuel Consumption for Heavy-Duty Vehicle

Energy Technology Data Exchange (ETDEWEB)

Wang, Lijuan; Kelly, Kenneth; Walkowicz, Kevin; Duran, Adam

2015-10-16

The National Renewable Energy Laboratory's (NREL's) Fleet Test and Evaluations team recently conducted chassis dynamometer tests of a class 8 conventional regional delivery truck over the Heavy Heavy-Duty Diesel Truck (HHDDT), West Virginia University City (WVU City), and Composite International Truck Local and Commuter Cycle (CILCC) drive cycles. A quantitative study was conducted by analyzing the impacts of various factors on fuel consumption (FC) and fuel economy (FE) by modeling and simulating the truck using NREL's Future Automotive Systems Technology Simulator (FASTSim). Factors used in this study included vehicle weight, and the coefficients of rolling resistance and aerodynamic drag. The simulation results from a single parametric study revealed that FC was approximately a linear function of the weight, coefficient of aerodynamic drag, and rolling resistance over various drive cycles. Among these parameters, the truck weight had the largest effect on FC. The study of the impact of two technologies on FE suggested that, depending on the circumstances, it may be more cost effective to reduce one parameter (such as coefficient of aerodynamic drag) to increase fuel economy, or it may be more beneficial to reduce another (such as the coefficient of rolling resistance). It also provided a convenient way to estimate FE by interpolating within the parameter values and extrapolating outside of them. The simulation results indicated that the FC could be reduced from 38.70 L/100 km, 50.72 L/100 km, and 38.42 L/100 km in the baseline truck to 26.78 L/100 km, 43.14 L/100 km and 29.84 L/100 km over the HHDDT, WVU City and CILCC drive cycles, respectively, when the U.S. Department of Energy's three targeted new technologies were applied simultaneously.

Experimental analysis of ethanol dual-fuel combustion in a heavy-duty diesel engine: An optimisation at low load

International Nuclear Information System (INIS)

Pedrozo, Vinícius B.; May, Ian; Dalla Nora, Macklini; Cairns, Alasdair; Zhao, Hua

2016-01-01

Highlights: • Dual-fuel combustion offers promising results on a stock heavy-duty diesel engine. • The use of split diesel injections extends the benefits of the dual-fuel mode. • Ethanol–diesel dual-fuel combustion results in high indicated efficiencies. • NOx and soot emissions are significantly reduced. • Combustion efficiency reaches 98% with an ethanol energy ratio of 53%. - Abstract: Conventional diesel combustion produces harmful exhaust emissions which adversely affect the air quality if not controlled by in-cylinder measures and exhaust aftertreatment systems. Dual-fuel combustion can potentially reduce the formation of nitrogen oxides (NOx) and soot which are characteristic of diesel diffusion flame. The in-cylinder blending of different fuels to control the charge reactivity allows for lower local equivalence ratios and temperatures. The use of ethanol, an oxygenated biofuel with high knock resistance and high latent heat of vaporisation, increases the reactivity gradient. In addition, renewable biofuels can provide a sustainable alternative to petroleum-based fuels as well as reduce greenhouse gas emissions. However, ethanol–diesel dual-fuel combustion suffers from poor engine efficiency at low load due to incomplete combustion. Therefore, experimental studies were carried out at 1200 rpm and 0.615 MPa indicated mean effective pressure on a heavy-duty diesel engine. Fuel delivery was in the form of port fuel injection of ethanol and common rail direct injection of diesel. The objective was to improve combustion efficiency, maximise ethanol substitution, and minimise NOx and soot emissions. Ethanol energy fractions up to 69% were explored in conjunction with the effect of different diesel injection strategies on combustion, emissions, and efficiency. Optimisation tests were performed for the optimum fuelling and diesel injection strategy. The resulting effects of exhaust gas recirculation, intake air pressure, and rail pressure were

150 years of Rudolf Diesel; 150 Jahre Rudolf Diesel

Energy Technology Data Exchange (ETDEWEB)

Basshuysen, R. van; Siebenpfeiffer, W. (eds.)

2008-03-15

'My engine is still making great progress', Rudolf Diesel wrote in a letter to his wife on 3 July 1895. The fact that Diesel's statement still holds true can be seen every day on our roads and at sea. But it is equally true that the idea of this eccentric and doubter who wanted to dedicate himself with an over-inflated self-belief to the welfare of humanity, needed a certain time to take a form that others could recognise in order to continuously refine this life's work. Diesel himself did not live to see most of the milestones that were repeatedly set thanks to his engine. It was not until 23 years after his unexplained death in 1913 that people were able to buy the first passenger car to be equipped with a diesel engine - with a top speed of 90 km/h. Today, diesel cars can easily reach speeds of up to 300 km/h, and even if there is little point in such excessive speeds outside racetracks like Le Mans, they are nevertheless clear evidence of the incredible evolution of the noisy, smoky truck engine to a high-tech racing power unit, from the ear-splitting rattle of the pre-chamber diesel to the highly refined, soot-free, common-rail diesel engine of today. The Publisher hopes you enjoy reading this unique progress report. (orig.)

Optimising the cam profile of an electronic unit pump for a heavy-duty diesel engine

International Nuclear Information System (INIS)

Qiu, Tao; Dai, Hefei; Lei, Yan; Cao, Chunlei; Li, Xuchu

2015-01-01

For a fuel system with a tangent cam or a constant-velocity cam, the peak injection pressure continues to rise as the injection duration increases, but overly high peak pressures induce mechanical loads and wear, limiting the maximum engine speed and injection quantity. To improve the performance of an EUP (Electronic Unit Pump) fuel system for heavy-duty diesel engines, this work proposes a new pump cam, namely the constant-pressure cam. It helps the EUP run at a higher speed and deliver larger fuel quantities while maintaining a constant peak injection pressure, which improves the power of the heavy-duty diesel engine. A model based on the EUP was built to determine the three constraints for optimising the constant-pressure cam: 1) the pump pressure should equal the nozzle pressure; 2) the cam speed should decrease with the increase in the injection duration; and 3) the cam acceleration gradient should be zero. An EUP system was tested with the tangent cam and the optimised cam under different conditions. The experimental results show that the EUP system with the optimised cam delivers more injection quantity and runs at higher engine speeds while maintaining the same peak pressure as the tangent cam. - Highlights: • We propose a constant-pressure cam to improve the power of heavy-duty diesel engine. • We deduce three constraints for the CP (constant-peak pressure) cam based on a model. • The EUP system with the new cam works well under higher engine speed. • The peak pressure of the constant-pressure cam fuel system maintains high

Truckstop - and Truck - Electrification

International Nuclear Information System (INIS)

Skip Yeakel

2001-01-01

The conclusions of this paper are: 0.5-1.5 G/H and/or BUSG/Y-how much time and money will it take to quantify and WHY BOTHER TO DO SO? No shortage of things to do re truckstop-+ truck - electrification; Better that government and industry should put many eggs in lots of baskets vs. all in one or few; Best concepts will surface as most viable; Economic appeal better than regulation or brute force; Launch Ground Freight Partnership and give it a chance to work; Demonstration is an effective means to educate, and learn from, customers-learning is a two way street; Research, Development, Demonstration, and Deployment (RD 3) are all important but only deployment gets results; TSE can start small in numbers of spaces to accommodate economically inspired growth but upfront plans should be made for expansion if meaningful idle reduction is to follow via TE; 110VAC 15A service/ parking space is minimal-if infrastructure starts like this, upfront plans must be made to increase capacity; Increased electrification of truckstop and truck alike will result in much better life on the road; Improved sleep will improve driver alertness and safety; Reduced idling will significantly reduce fuel use and emissions; Universal appeal for DOD, DOE, DOT, EPA, OEMs, and users alike; Clean coal, gas, hydro, nuclear, or wind energy sources are all distinctly American means by which to generate electricity; Nothing can compete with diesel fuel to serve mobile truck needs; stationary trucks are like power plants-they don't move and should NOT be powered by petroleum products whenever possible; Use American fueled power plants-electricity-to serve truck idling needs wherever practical to do so; encourage economic aspect; Create and reward industry initiatives to reduce fuel use; Eliminate FET on new trucks, provide tax credits (non highway fuel use and investment), provide incentives based on results; Encourage newer/ cleaner truck use; solicit BAAs with mandatory OEM/ fleet participation/ lead

UPS CNG Truck Fleet Start Up Experience: Alternative Fuel Truck Evaluation Project

International Nuclear Information System (INIS)

Walkowicz, K.

2001-01-01

UPS operates 140 Freightliner Custom Chassis compressed natural gas (CNG)-powered vehicles with Cummins B5.9G engines. Fifteen are participating in the Alternative Fuel Truck Evaluation Project being funded by DOE's Office of Transportation Technologies and the Office of Heavy Vehicle Technologies

Combustion and emissions characteristics of high n-butanol/diesel ratio blend in a heavy-duty diesel engine and EGR impact

International Nuclear Information System (INIS)

Chen, Zheng; Wu, Zhenkuo; Liu, Jingping; Lee, Chiafon

2014-01-01

Highlights: • Effects of EGR on high n-butanol/diesel ratio blend (Bu40) were investigated and compared with neat diesel (Bu00). • Bu40 has higher NOx due to wider combustion high-temperature region. • Bu40 has lower soot due to local lower equivalence ratio distribution. • Bu40 has higher CO due to lower gas temperature in the late expansion process. • For Bu40, EGR reduces NOx emissions dramatically with no obvious influence on soot. - Abstract: In this work, the combustion and emission fundamentals of high n-butanol/diesel ratio blend with 40% butanol (i.e., Bu40) in a heavy-duty diesel engine were investigated by experiment and simulation at constant engine speed of 1400 rpm and an IMEP of 1.0 MPa. Additionally, the impact of EGR was evaluated experimentally and compared with neat diesel fuel (i.e., Bu00). The results show that Bu40 has higher cylinder pressure, longer ignition delay, and faster burning rate than Bu00. Compared with Bu00, moreover, Bu40 has higher NOx due to wider combustion high-temperature region, lower soot due to local lower equivalence ratio distribution, and higher CO due to lower gas temperature in the late expansion process. For Bu40, EGR reduces NOx emissions dramatically with no obvious influence on soot. Meanwhile, there is no significant change in HC and CO emissions and indicated thermal efficiency (ITE) with EGR until EGR threshold is reached. When EGR rate exceeds the threshold level, HC and CO emissions increase dramatically, and ITE decreases markedly. Compared with Bu00, the threshold of Bu40 appears at lower EGR rate. Consequently, combining high butanol/diesel ratio blend with medium EGR has the potential to achieve ultra-low NOx and soot emissions simultaneously while maintaining high thermal efficiency level

Experimental study into a hybrid PCCI/CI concept for next-generation heavy-duty diesel engines

NARCIS (Netherlands)

Doosje, E.; Willems, F.P.T.; Baert, R.S.G.; Dijk, M.D. van

2012-01-01

This paper presents the first results of an experimental study into a hybrid combustion concept for next-generation heavy-duty diesel engines. In this hybrid concept, at low load operating conditions, the engine is run in Pre-mixed Charge Compression Ignition (PCCI) mode, whereas at high load

Methods of rational fuel consumption by the dump trucks in deep pits

Directory of Open Access Journals (Sweden)

Yu. I. Lel’

2017-12-01

Full Text Available The detailed analysis of “consumption Norms of fuel and lubricants...” has been performed. It was approved by the Ministry of transport of the Russian Federation and it is an official document for the valuation and planning of fuel consumption in road transport, including open pits. It was found that the “rate...” was deficient in the specific operating conditions of mining dump trucks and a significant discrepancy with the actual fuel consumption. To the greatest extent, these shortcomings are noticeable in deep pits. In the result of experimental and analytical studies a new method of rationing the diesel fuel consumption of mining dump trucks was developed. It is based on the calculation of fuel consumption for vehicle cycle and bringing the actual path length to the conventional horizontal transportation distances using the criterion of energy. This method requires comprehensive consideration of the design parameters of mining dump trucks – mining and road traffic conditions. As a criterion for evaluating the difficulty of transporting it justifies the use of the coefficient of difficulty of the course, showing how many times the energy consumption in the movement of trucks on the highway exceed the real energy consumption while driving on a horizontal road with the crushed-stone surface of the same length. The formulae are derived to determine the given distance of transportation on the basis of the horizontal equivalent of the vertical movement of the rock mass. It was found that the linear rate of flow of diesel fuel to mileage and transportation work under other equal conditions is determined by two main factors: the distance of transportation of L and the coefficient μ of difficulty of the course. As an example, the calculation of the linear differentiated norms of fuel consumption of dump trucks CAT 785B in an “Udachny” pit AK “ALROSA” (JSC. The developed method provides high accuracy of regulation of diesel fuel

Should Diesel cars in Europe be discouraged?

OpenAIRE

Mayeres, Inge; Proost, Stef

2001-01-01

This paper examines the rationale for the different tax treatment of gasoline and diesel cars currently observed in Europe. First, we analyse possible justifications for a different tax treatment: pure tax revenue considerations, externality cons0iderations and constraints on the tax instruments used for cars and trucks. Next, an applied general equilibrium model is used to assess the welfare effects of revenue neutral changes in the vehicle and fuel taxes on diesel and gasoline cars. The mod...

The effect of the position of oxygen group to the aromatic ring to emission performance in a heavy-duty diesel engine

NARCIS (Netherlands)

Zhou, L.; Boot, M.D.; Goey, de L.P.H.

2012-01-01

In this paper the soot-NOx trade-off and fuel efficiency of various aromatic oxygenates is investigated in a modern DAF heavy-duty diesel engine. All oxygenates were blended to diesel fuel such that the blend oxygen concentration was 2.59 wt.-%. The oxygenates in question, anisole, benzyl alcohol

Demand Forecasting for Heavy-Duty Diesel Engines Considering Emission Regulations

Directory of Open Access Journals (Sweden)

Yoon Seong Kim

2017-01-01

Full Text Available Makers of heavy-duty diesel engines (HDDEs need to reduce their inventory of old-generation products in preparation for the demand for next-generation products that satisfy new emission regulations. In this paper, a new demand forecasting model is proposed to reflect special conditions raised by the technological generational shift owing to new emission regulation enforcement. In addition, sensitivity analyses are conducted to better accommodate uncertainty involved at the time of prediction. Our proposed model can help support manufacturers’ production and sales management for a series of products in response to new emission regulations.

Lithium-Ion Battery Cell Cycling and Usage Analysis in a Heavy-Duty Truck Field Study

Directory of Open Access Journals (Sweden)

Pontus Svens

2015-05-01

Full Text Available This paper presents results from a field test performed on commercial power-optimized lithium-ion battery cells cycled on three heavy-duty trucks. The goal with this study was to age battery cells in a hybrid electric vehicle (HEV environment and find suitable methods for identifying cell ageing. The battery cells were cycled on in-house developed equipment intended for testing on conventional vehicles by emulating an HEV environment. A hybrid strategy that allows battery usage to vary within certain limits depending on driving patterns was used. This concept allows unobtrusive and low-cost testing of battery cells under realistic conditions. Each truck was equipped with one cell cycling equipment and two battery cells. One cell per vehicle was cycled during the test period while a reference cell on each vehicle experienced the same environmental conditions without being cycled. Differential voltage analysis and electrochemical impedance spectroscopy were used to identify ageing of the tested battery cells. Analysis of driving patterns and battery usage was performed from collected vehicle data and battery cell data.

Impact of fuels on diesel exhaust emissions

International Nuclear Information System (INIS)

Westerholm, R.

1991-09-01

This report presents an investigation of the emissions from eight diesel fuels with different sulphur and aromatic content. A bus and a truck were used in the investigation. Chemical analysis and biological testing have been performed. The aim of this project was to find a 'good' diesel fuel which can be used in urban areas. Seven of the fuels were meant to be such fuels. It has been confirmed in this study that there exists a quantifiable relationship between the variables of the diesel fuel blends and the variables of the chemical emissions and their biological effects. 119 figs., 12 tabs., approx. 100 refs

Recycling used palm oil and used engine oil to produce white bio oil, bio petroleum diesel and heavy fuel

Science.gov (United States)

Al-abbas, Mustafa Hamid; Ibrahim, Wan Aini Wan; Sanagi, Mohd. Marsin

2012-09-01

Recycling waste materials produced in our daily life is considered as an additional resource of a wide range of materials and it conserves the environment. Used engine oil and used cooking oil are two oils disposed off in large quantities as a by-product of our daily life. This study aims at providing white bio oil, bio petroleum diesel and heavy fuel from the disposed oils. Toxic organic materials suspected to be present in the used engine oil were separated using vacuum column chromatography to reduce the time needed for the separation process and to avoid solvent usage. The compounds separated were detected by gas chromatography-mass spectrometry (GC-MS) and found to contain toxic aromatic carboxylic acids. Used cooking oils (thermally cracked from usage) were collected and separated by vacuum column chromatography. White bio oil produced was examined by GC-MS. The white bio oil consists of non-toxic hydrocarbons and is found to be a good alternative to white mineral oil which is significantly used in food industry, cosmetics and drugs with the risk of containing polycyclic aromatic compounds which are carcinogenic and toxic. Different portions of the used cooking oil and used engine were mixed to produce several blends for use as heavy oil fuels. White bio oil was used to produce bio petroleum diesel by blending it with petroleum diesel and kerosene. The bio petroleum diesel produced passed the PETRONAS flash point and viscosity specification test. The heat of combustion of the two blends of heavy fuel produced was measured and one of the blends was burned to demonstrate its burning ability. Higher heat of combustion was obtained from the blend containing greater proportion of used engine oil. This study has provided a successful recycled alternative for white bio oil, bio petroleum fuel and diesel which can be an energy source.

Quantitative nitric oxide measurements by means of laser-induced fluorescence in a heavy-duty Diesel engine

NARCIS (Netherlands)

Verbiezen, K.; Vliet, van A.P.; Klein-Douwel, R.J.H.; Ganippa, L.C.; Bougie, H.J.T.; Meerts, W.L.; Dam, N.J.; Meulen, ter J.J.

2005-01-01

Quantitative in-cylinder laser-induced fluorescence measurements ofnitric oxide in a heavy-duty Diesel engine are presented. Special attention is paid to experimental techniques to assess the attenuation of the laser beam and the fluorescence signal by the cylinder contents.This attenuation can be

Effects of biodiesel, engine load and diesel particulate filter on nonvolatile particle number size distributions in heavy-duty diesel engine exhaust.

Science.gov (United States)

Young, Li-Hao; Liou, Yi-Jyun; Cheng, Man-Ting; Lu, Jau-Huai; Yang, Hsi-Hsien; Tsai, Ying I; Wang, Lin-Chi; Chen, Chung-Bang; Lai, Jim-Shoung

2012-01-15

Diesel engine exhaust contains large numbers of submicrometer particles that degrade air quality and human health. This study examines the number emission characteristics of 10-1000 nm nonvolatile particles from a heavy-duty diesel engine, operating with various waste cooking oil biodiesel blends (B2, B10 and B20), engine loads (0%, 25%, 50% and 75%) and a diesel oxidation catalyst plus diesel particulate filter (DOC+DPF) under steady modes. For a given load, the total particle number concentrations (N(TOT)) decrease slightly, while the mode diameters show negligible changes with increasing biodiesel blends. For a given biodiesel blend, both the N(TOT) and mode diameters increase modestly with increasing load of above 25%. The N(TOT) at idle are highest and their size distributions are strongly affected by condensation and possible nucleation of semivolatile materials. Nonvolatile cores of diameters less than 16 nm are only observed at idle mode. The DOC+DPF shows remarkable filtration efficiency for both the core and soot particles, irrespective of the biodiesel blend and engine load under study. The N(TOT) post the DOC+DPF are comparable to typical ambient levels of ≈ 10(4)cm(-3). This implies that, without concurrent reductions of semivolatile materials, the formation of semivolatile nucleation mode particles post the after treatment is highly favored. Copyright © 2011 Elsevier B.V. All rights reserved.

Differences between emissions measured in urban driving and certification testing of heavy-duty diesel engines

Science.gov (United States)

Dixit, Poornima; Miller, J. Wayne; Cocker, David R.; Oshinuga, Adewale; Jiang, Yu; Durbin, Thomas D.; Johnson, Kent C.

2017-10-01

Emissions from eight heavy-duty diesel trucks (HDDTs) equipped with three different exhaust aftertreatment systems (ATS) for controlling nitrogen oxide (NOx) emissions were quantified on a chassis dynamometer using driving schedules representative of stop-and-go and free-flow driving in metropolitan areas. The three control technologies were: 1) cooled exhaust gas recirculation (CEGR) plus a diesel particulate filter (DPF); 2) CEGR and DPF plus advanced engine controls; and 3) CEGR and DPF plus selective catalytic reduction with ammonia (SCR). Results for all control technologies and driving conditions showed PM emission factors were less than the standard, while selected non-regulated emissions (ammonia, carbonyls, and C4-C12 hydrocarbons) and a greenhouse gas (nitrous oxide) were at measurement detection limits. However, NOx emission factors depended on the control technology, engine calibration, and driving mode. For example, emissions from engines with cooled-exhaust gas recirculation (CEGR) were 239% higher for stop-and-go driving as compared with free-flow. For CEGR plus selective catalytic reduction (SCR), the ratio was 450%. A deeper analysis was carried out with the assumption that emissions measured for a drive cycle on either the chassis or in-use driving would be similar. Applying the same NTE rules to the chassis data showed emissions during stop-and-go driving often exceeded the certification standard and >90% of the driving did not fall within the Not-To-Exceed (NTE) control area suggesting the NTE requirements do not provide sufficient emissions control under in-use conditions. On-road measurement of emissions using the same mobile lab while the vehicle followed a free-flow driving schedule verified the chassis results. These results have implications for scientists who build inventories using certification values instead of real world emission values and for metropolitan populations, who are exposed to elevated emissions. The differences in values

Trucks involved in fatal accidents codebook 2010 (Version October 22, 2012).

Science.gov (United States)

2012-11-01

This report provides documentation for UMTRIs file of Trucks Involved in Fatal Accidents : (TIFA), 2010, including distributions of the code values for each variable in the file. The 2010 : TIFA file is a census of all medium and heavy trucks invo...

In-use NOx emissions from model year 2010 and 2011 heavy-duty diesel engines equipped with aftertreatment devices.

Science.gov (United States)

Misra, Chandan; Collins, John F; Herner, Jorn D; Sax, Todd; Krishnamurthy, Mohan; Sobieralski, Wayne; Burntizki, Mark; Chernich, Don

2013-07-16

The California Air Resources Board (ARB) undertook this study to characterize the in-use emissions of model year (MY) 2010 or newer diesel engines. Emissions from four trucks: one equipped with an exhaust gas recirculation (EGR) and three equipped with EGR and a selective catalytic reduction (SCR) device were measured on two different routes with three different payloads using a portable emissions measurement system (PEMS) in the Sacramento area. Results indicated that brake-specific NOx emissions for the truck equipped only with an EGR were independent of the driving conditions. Results also showed that for typical highway driving conditions, the SCR technology is proving to be effective in controlling NOx emissions. However, under operations where the SCR's do not reach minimum operating temperature, like cold starts and some low load/slow speed driving conditions, NOx emissions are still elevated. The study indicated that strategies used to maintain exhaust temperature above a certain threshold, which are used in some of the newer SCRs, have the potential to control NOx emissions during certain low-load/slow speed driving conditions.

A heavy load for heavy ions

CERN Multimedia

2003-01-01

On 25 September, the two large coils for the dipole magnet of ALICE, the LHC experiment dedicated to heavy ions, arrived at Point 2 on two heavy load trucks after a 1200 km journey from their assembly in Vannes, France.

Gas density and rail pressure effects on diesel spray growth from a heavy-duty common rail injector

NARCIS (Netherlands)

Klein-Douwel, R.J.H.; Frijters, P.J.M.; Seykens, X.L.J.; Somers, L.M.T.; Baert, R.S.G.

2009-01-01

Formation of nonevaporating sprays from diesel fuel injection through a realistic heavy duty multihole common rail injector is studied in a newly developed high-pressure, high-temperature cell, using digital highspeed shadowgraphy at 4500 frames/s. Gas pressure was varied from 13 to 37 bar

Study of turbocharged diesel engine operation, pollutant emissions and combustion noise radiation during starting with bio-diesel or n-butanol diesel fuel blends

International Nuclear Information System (INIS)

Rakopoulos, C.D.; Dimaratos, A.M.; Giakoumis, E.G.; Rakopoulos, D.C.

2011-01-01

Highlights: → Turbocharged diesel engine emissions during starting with bio-diesel or n-butanol diesel blends. → Peak pollutant emissions due to turbo-lag. → Significant bio-diesel effects on combustion behavior and stability. → Negative effects on NO emissions for both blends. → Positive effects on smoke emissions only for n-butanol blend. -- Abstract: The control of transient emissions from turbocharged diesel engines is an important objective for automotive manufacturers, as stringent criteria for exhaust emissions must be met. Starting, in particular, is a process of significant importance owing to its major contribution to the overall emissions during a transient test cycle. On the other hand, bio-fuels are getting impetus today as renewable substitutes for conventional fuels, especially in the transport sector. In the present work, experimental tests were conducted at the authors' laboratory on a bus/truck, turbocharged diesel engine in order to investigate the formation mechanisms of nitric oxide (NO), smoke, and combustion noise radiation during hot starting for various alternative fuel blends. To this aim, a fully instrumented test bed was set up, using ultra-fast response analyzers capable of capturing the instantaneous development of emissions as well as various other key engine and turbocharger parameters. The experimental test matrix included three different fuels, namely neat diesel fuel and two blends of diesel fuel with either bio-diesel (30% by vol.) or n-butanol (25% by vol.). With reference to the neat diesel fuel case during the starting event, the bio-diesel blend resulted in deterioration of both pollutant emissions as well as increased combustion instability, while the n-butanol (normal butanol) blend decreased significantly exhaust gas opacity but increased notably NO emission.

Truck side guard specifications : recommended standard

Science.gov (United States)

2016-09-01

This document is intended to be used by (1) public or private medium/heavy-duty truck fleets considering adding side guards; (2) jurisdictions or customers that require side guards through policy or procurement; (3) manufacturers of side guards; and ...

COMPARISON OF THE PARTICLE SIZE DISTRIBUTION OF HEAVY-DUTY DIESEL EXHAUST USING A DILUTION TAIL-PIPE SAMPLER AND IN-PLUME SAMPLER DURING ON-ROAD OPERATION

Science.gov (United States)

The paper compares the particle size distribution of heavy-duty diesel exhaust using a dilution tail-pipe sampler and an in-plume sampler during on-road operation. EPA's On-road Diesel Emissions Characterization Facility, modified to incorporate particle measurement instrumentat...

Gas density and rail pressure effects on diesel spray growth from a heavy-duty common rail injector

NARCIS (Netherlands)

Klein-Douwel, R.J.H.; Frijters, P.J.M.; Seykens, X.L.J.; Somers, L.M.T.; Baert, R.S.G.

2009-01-01

Formation of nonevaporating sprays from diesel fuel injection through a realistic heavy duty multihole common rail injector is studied in a newly developed high-pressure, high-temperature cell, using digital high-speed shadowgraphy at 4500 frames/s. Gas pressure was varied from 13 to 37 bar

Chassis dynamometer study of emissions from 21 in-use heavy-duty diesel vehicles

International Nuclear Information System (INIS)

Yanowitz, J.; Graboski, M.S.; Ryan, L.B.A.; Alleman, T.L.; McCormick, R.L.

1999-01-01

Regulated emissions from 21 in-use heavy-duty diesel vehicles were measured on a heavy-duty chassis dynamometer via three driving cycles using a low-sulfur diesel fuel. Emissions of particulate matter (PM), nitrogen oxides (NO x ), carbon monoxide (CO), total hydrocarbon (THC), and PM sulfate fraction were measured. For hot start tests, emissions ranged from 0.30 to 7.43 g/mi (mean 1.96) for PM; 4.15--54.0 g/mi (mean 23.3) for NO x ; 2.09--86.2 g/mi (mean 19.5) for CO; and 0.25--8.25 g/mi (mean 1.70) for THC. When emissions are converted to a g/gal basis, the effect of driving cycle is eliminated for NO x and largely eliminated for PM. Sulfate comprised less than 1% of the emitted PM for all vehicles and test cycles. A strong correlation is observed between emissions of CO and PM. Cold starting at 77 F produced an 11% increase in PM emissions. Multivariate regression analyses indicate that in-use PM emissions have decreased at a slower rate than anticipated based on the stricter engine certification test standards put into effect since 1985. NO x emissions do not decrease with model year for the vehicles tested here. Smoke opacity measurements are not well correlated with mass emissions of regulated pollutants

Medium-Duty Plug-in Electric Delivery Truck Fleet Evaluation

Energy Technology Data Exchange (ETDEWEB)

Prohaska, Robert; Ragatz, Adam; Simpson, Mike; Kelly, Kenneth

2016-06-29

In this paper, the authors present an overview of medium-duty electric vehicle (EV) operating behavior based on in-use data collected from Smith Newton electric delivery vehicles and compare their performance and operation to conventional diesel trucks operating in the same fleet. The vehicles' drive cycles and operation are analyzed and compared to demonstrate the importance of matching specific EV technologies to the appropriate operational duty cycle. The results of this analysis show that the Smith Newton EVs demonstrated a 68% reduction in energy consumption over the data reporting period compared to the conventional diesel vehicles, as well as a 46.4% reduction in carbon dioxide equivalent emissions based on the local energy generation source.

Development of database of real-world diesel vehicle emission factors for China.

Science.gov (United States)

Shen, Xianbao; Yao, Zhiliang; Zhang, Qiang; Wagner, David Vance; Huo, Hong; Zhang, Yingzhi; Zheng, Bo; He, Kebin

2015-05-01

A database of real-world diesel vehicle emission factors, based on type and technology, has been developed following tests on more than 300 diesel vehicles in China using a portable emission measurement system. The database provides better understanding of diesel vehicle emissions under actual driving conditions. We found that although new regulations have reduced real-world emission levels of diesel trucks and buses significantly for most pollutants in China, NOx emissions have been inadequately controlled by the current standards, especially for diesel buses, because of bad driving conditions in the real world. We also compared the emission factors in the database with those calculated by emission factor models and used in inventory studies. The emission factors derived from COPERT (Computer Programmer to calculate Emissions from Road Transport) and MOBILE may both underestimate real emission factors, whereas the updated COPERT and PART5 (Highway Vehicle Particulate Emission Modeling Software) models may overestimate emission factors in China. Real-world measurement results and emission factors used in recent emission inventory studies are inconsistent, which has led to inaccurate estimates of emissions from diesel trucks and buses over recent years. This suggests that emission factors derived from European or US-based models will not truly represent real-world emissions in China. Therefore, it is useful and necessary to conduct systematic real-world measurements of vehicle emissions in China in order to obtain the optimum inputs for emission inventory models. Copyright © 2015. Published by Elsevier B.V.

AUTOMOTIVE DIESEL MAINTENANCE 2. UNIT II, MECHANICAL TRANSMISSIONS.

Science.gov (United States)

Human Engineering Inst., Cleveland, OH.

THIS MODULE OF A 25-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF MECHANICAL TRANSMISSIONS USED ON DIESEL POWERED VEHICLES. TOPICS ARE (1) PURPOSE OF TRANSMISSIONS, (2) RATIO DIFFERENCE, (3) CONSTANT MESH TRANSMISSIONS, (4) FOUR-SPEED TRUCK TRANSMISSION POWER FLOW, AND (5) TRANSMISSION TROUBLESHOOTING.…

The effects of fuel characteristics and engine operating conditions on the elemental composition of emissions from heavy duty diesel buses

Energy Technology Data Exchange (ETDEWEB)

M.C.H. Lim; G.A. Ayoko; L. Morawska; Z.D. Ristovski; E.R. Jayaratne [Queensland University of Technology, Brisbane, Qld. (Australia). International Laboratory for Air Quality and Health, School of Physical and Chemical Sciences

2007-08-15

The effects of fuel characteristics and engine operating conditions on elemental composition of emissions from twelve heavy duty diesel buses have been investigated. Two types of diesel fuels - low sulfur diesel (LSD) and ultra low sulfur diesel (ULSD) fuels with 500 ppm and 50 ppm sulfur contents respectively and 3 driving modes corresponding to 25%, 50% and 100% power were used. Elements present in the tailpipe emissions were quantified by inductively coupled plasma mass spectrometry (ICPMS) and those found in measurable quantities included Mg, Ca, Cr, Fe, Cu, Zn, Ti, Ni, Pb, Be, P, Se, Ti and Ge. Multivariate analyses using multi-criteria decision making methods (MCDM), principal component analysis (PCA) and partial least squares (PLS) facilitated the extraction of information about the structure of the data. MCDM showed that the emissions of the elements were strongly influenced by the engine driving conditions while the PCA loadings plots showed that the emission factors of the elements were correlated with those of other pollutants such as particle number, total suspended particles, CO, CO{sub 2} and NOx. Partial least square analysis revealed that the emission factors of the elements were strongly dependent on the fuel parameters such as the fuel sulfur content, fuel density, distillation point and cetane index. Strong correlations were also observed between these pollutants and the engine power or exhaust temperature. The study provides insights into the possible role of fuel sulfur content in the emission of inorganic elements from heavy duty diesel vehicles. 39 refs., 1 fig., 4 tabs.

Regulated and unregulated emissions from modern 2010 emissions-compliant heavy-duty on-highway diesel engines.

Science.gov (United States)

Khalek, Imad A; Blanks, Matthew G; Merritt, Patrick M; Zielinska, Barbara

2015-08-01

The U.S. Environmental Protection Agency (EPA) established strict regulations for highway diesel engine exhaust emissions of particulate matter (PM) and nitrogen oxides (NOx) to aid in meeting the National Ambient Air Quality Standards. The emission standards were phased in with stringent standards for 2007 model year (MY) heavy-duty engines (HDEs), and even more stringent NOX standards for 2010 and later model years. The Health Effects Institute, in cooperation with the Coordinating Research Council, funded by government and the private sector, designed and conducted a research program, the Advanced Collaborative Emission Study (ACES), with multiple objectives, including detailed characterization of the emissions from both 2007- and 2010-compliant engines. The results from emission testing of 2007-compliant engines have already been reported in a previous publication. This paper reports the emissions testing results for three heavy-duty 2010-compliant engines intended for on-highway use. These engines were equipped with an exhaust diesel oxidation catalyst (DOC), high-efficiency catalyzed diesel particle filter (DPF), urea-based selective catalytic reduction catalyst (SCR), and ammonia slip catalyst (AMOX), and were fueled with ultra-low-sulfur diesel fuel (~6.5 ppm sulfur). Average regulated and unregulated emissions of more than 780 chemical species were characterized in engine exhaust under transient engine operation using the Federal Test Procedure cycle and a 16-hr duty cycle representing a wide dynamic range of real-world engine operation. The 2010 engines' regulated emissions of PM, NOX, nonmethane hydrocarbons, and carbon monoxide were all well below the EPA 2010 emission standards. Moreover, the unregulated emissions of polycyclic aromatic hydrocarbons (PAHs), nitroPAHs, hopanes and steranes, alcohols and organic acids, alkanes, carbonyls, dioxins and furans, inorganic ions, metals and elements, elemental carbon, and particle number were substantially (90

An experimental investigation of the combustion process of a heavy-duty diesel engine enriched with H{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Liew, C.; Li, H.; Nuszkowski, J.; Liu, S.; Gatts, T.; Atkinson, R.; Clark, N. [Department of Mechanical and Aerospace Engineering, West Virginia University, Morgantown, WV 26506-6106 (United States)

2010-10-15

This paper investigated the effect of hydrogen (H{sub 2}) addition on the combustion process of a heavy-duty diesel engine. The addition of a small amount of H{sub 2} was shown to have a mild effect on the cylinder pressure and combustion process. When operated at high load, the addition of a relatively large amount of H{sub 2} substantially increased the peak cylinder pressure and the peak heat release rate. Compared to the two-stage combustion process of diesel engines, a featured three-stage combustion process of the H{sub 2}-diesel dual fuel engine was observed. The extremely high peak heat release rate represented a combination of diesel diffusion combustion and the premixed combustion of H{sub 2} consumed by multiple turbulent flames, which substantially enhanced the combustion process of H{sub 2}-diesel dual fuel engine. However, the addition of a relatively large amount of H{sub 2} at low load did not change the two-stage heat release process pattern. The premixed combustion was dramatically inhibited while the diffusion combustion was slightly enhanced and elongated. The substantially reduced peak cylinder pressure at low load was due to the deteriorated premixed combustion. (author)

Praktična prilagodba klasičnih uređaja za ubrizgavanje goriva u motorima velike snage za teretna vozila

Directory of Open Access Journals (Sweden)

Anton Černaj

2012-10-01

Full Text Available Basic requirements related to fuel injection system of upgradedturbocharged articulated truck diesel engines are listedand discussed. An example of the FIE matching approach toupgrading of a heavy duty diesel engine is presented. The applicationof hollow cam fuel injection pump may offer a furtherextension of its use in order to uprate diesel engine peiformance.

Soot particulate size characterisation in a heavy-duty diesel engine for different engine loads by laser-induced incandescence

NARCIS (Netherlands)

Bougie, B.; Ganippa, L.C.; Vliet, van A.P.; Meerts, W.L.; Dam, N.J.; Meulen, ter J.J.

2007-01-01

Time-resolved laser-induced incandescence was used to estimate primary particle size distributions inside the combustion chamber of a heavy-duty diesel engine as a function of the crank angle, for two different engine loads at two different probe locations. Assuming a log-normal particle size

Research on Correlation between Vehicle Cycle and Engine Cycle in Heavy-duty commercial vehicle

Science.gov (United States)

lin, Chen; Zhong, Wang; Shuai, Liu

2017-12-01

In order to study the correlation between vehicle cycle and engine cycle in heavy commercial vehicles, the conversion model of vehicle cycle to engine cycle is constructed based on the vehicle power system theory and shift strategy, which considers the verification on diesel truck. The results show that the model has high rationality and reliability in engine operation. In the acceleration process of high speed, the difference of model gear selection leads to the actual deviation. Compared with the drum test, the engine speed distribution obtained by the model deviates to right, which fits to the lower grade. The grade selection has high influence on the model.

Particulate morphology of waste cooking oil biodiesel and diesel in a heavy duty diesel engine

Science.gov (United States)

Hwang, Joonsik; Jung, Yongjin; Bae, Choongsik

2014-08-01

The effect of biodiesel produced from waste cooking oil (WCO) on the particulate matters (PM) of a direct injection (DI) diesel engine was experimentally investigated and compared with commercial diesel fuel. Soot agglomerates were collected with a thermophoretic sampling device installed in the exhaust pipe of the engine. The morphology of soot particles was analyzed using high resolution transmission electron microscopy (TEM). The elemental and thermogravimetric analysis (TGA) were also conducted to study chemical composition of soot particles. Based on the TEM images, it was revealed that the soot derived from WCO biodiesel has a highly graphitic shell-core arrangement compared to diesel soot. The mean size was measured from averaging 400 primary particles for WCO biodiesel and diesel respectively. The values for WCO biodiesel indicated 19.9 nm which was smaller than diesel's 23.7 nm. From the TGA results, WCO biodiesel showed faster oxidation process. While the oxidation of soot particles from diesel continued until 660°C, WCO biodiesel soot oxidation terminated at 560°C. Elemental analysis results showed that the diesel soot was mainly composed of carbon and hydrogen. On the other hand, WCO biodiesel soot contained high amount of oxygen species.

Pre-study of exhaust gases of diesel engines with 'open' and 'wall-flow' diesel particulate filters and their toxicity

International Nuclear Information System (INIS)

Verbeek, R.; Rabe, E.

2007-04-01

The Dutch Ministry of VROM (Housing, Spatial Planning and the Environment) has recently introduced financial support programmes for the installation of Diesel Particulate Filters on both passenger cars and trucks. To obtain funding, the minimum filtration efficiency for passenger cars should be 30%. For trucks there are 2 categories: minimally 50% and minimally 90%. The 30 to 50% filtration efficiency is in practice realized with so called 'open' filters. More than 90% filtration efficiency is accomplished with the 'wall-flow' or 'closed' diesel particulate filter. All filters are combined with an integrated oxidation catalyst. The oxidation catalyst is necessary for the regeneration of the particulate matter captured within the filter; it will also oxidize and hence reduce components like unburned hydrocarbons and carbon monoxide. For any automotive catalytic after-treatment system there is theoretically a risk of undesirable reactions that might occur under certain conditions. Therefore, a number of international studies were conducted during the last decade to investigate the emission of potentially toxic components from diesel engines equipped with wall-flow diesel particulate filters and with oxidation catalysts. The results of these studies were generally positive: a reduction of many potentially toxic components and particulate mass although in some cases certain potentially toxic components had increased. The open filters have a very similar oxidation catalyst but a different way of filter trapping. The question was raised whether there would be significant risks of formation of certain potentially toxic components or ultra-fine particles that might be harmful for human health. VROM asked TNO to conduct this pre-study, which was also meant as a preparation for an experimental study. Several international studies as well as studies conducted by TNO during the past 8 years were evaluated with the focus on information on known toxic components, on particle

A battery-fuel cell hybrid auxiliary power unit for trucks: Analysis of direct and indirect hybrid configurations

International Nuclear Information System (INIS)

Samsun, Remzi Can; Krupp, Carsten; Baltzer, Sidney; Gnörich, Bruno; Peters, Ralf; Stolten, Detlef

2016-01-01

Highlights: • A battery-fuel cell hybrid auxiliary power unit for heavy duty vehicles is reported. • Comparison of direct and indirect hybrids using representative load profiles. • Evaluation based on validated fuel cell system and battery models. • Indirect hybrid with constant fuel cell load yields 29.3% hybrid system efficiency. • Fuel cell should be pre-heated using waste heat from the diesel engine during drive. - Abstract: The idling operation of engines in heavy duty vehicles to cover electricity demand during layovers entails significant fuel consumption and corresponding emissions. Indeed, this mode of operation is highly inefficient and a noteworthy contributor to the transportation sector’s aggregate carbon dioxide emissions. Here, a potential solution to this wasteful practice is outlined in the form of a hybrid battery-fuel cell system for application as an auxiliary power unit for trucks. Drawing on experimentally-validated fuel cell and battery models, several possible hybrid concepts are evaluated and direct and indirect hybrid configurations analyzed using a representative load profile. The results indicate that a direct hybrid configuration is only applicable if the load demand profile does not deviate strongly from the assumed profile. Operation of an indirect hybrid with a constant fuel cell load yields the greatest hybrid system efficiency, at 29.3%, while battery size could be reduced by 87% if the fuel cell is operated at the highest dynamics. Maximum efficiency in truck applications can be achieved by pre-heating the system prior to operation using exhaust heat from the motor, which increased system efficiency from 25.3% to 28.1%, including start-up. These findings confirm that hybrid systems could offer enormous fuel savings and constitute a sizeable step on the path toward energy-efficient and environmentally-friendly heavy duty vehicles that does not necessitate a fuel switch.

Fueling diesel engines with methyl-ester soybean oil

International Nuclear Information System (INIS)

Schumacher, L.G.; Hires, W.G.; Borgelt, S.C.

1993-01-01

Two 5.9 liter Cummins engines were fueled for a combined total of more than 80,467 km (50,000 miles). One truck, a 1991 Dodge, has been driven approximately 48,280 km (30,000 miles). The other, a 1992 Dodge, has been driven approximately 32,187 km (20,000 miles). Fueling these engines with soydiesel increase engine power by 3 percent (1991 engine) and reduced power by 6 percent (1992 engine). The pickups averaged more than 7.1 km/L (16.7 mpg). Analysis of used engine oil samples indicated that the engines were wearing at normal rate. The black exhaust smoke normally observed when a diesel engine accelerates was reduced as much as 86 percent when the diesel engine was fueled with 100% soydiesel. Increased EPA exhaust emissions requirements for diesel engines have created much interest in the use of soydiesel as fuel for diesel engines

Joint measurements of black carbon and particle mass for heavy-duty diesel vehicles using a portable emission measurement system

Science.gov (United States)

The black carbon (BC) emitted from heavy-duty diesel vehicles(HDDVs) is an important source of urban atmospheric pollution and createsstrong climate-forcing impacts. The emission ratio of BC to totalparticle mass (PM) (i.e., BC/PM ratio) is an essential variable used toestimate t...

Ventajas del uso de la inyección electrónica para vehículos diesel pesados en las condiciones de Cuba. // Advantages of electronic injection for diesel engines in heavy duty equipment.

Directory of Open Access Journals (Sweden)

J. Luis Reyes González

2002-09-01

Full Text Available Tomando en cuenta la importancia que tiene para Cuba el obtener una eficiencia energética elevada en los motores decombustión interna, al igual que el control de las emanaciones de gases tóxicos en los mismos, se realizó este trabajo dondese demuestran las ventajas tanto en el orden económico como ecológico de los motores diesel con mando electrónico paraequipos pesados empleados en la transportación de carga por camiones en la empresa Cubalse.Por medio de métodos experimentales y estadísticos, se obtuvo el consumo de combustible y la humosidad en motores coninyección electrónica (Detroit y en motores que utilizan los métodos tradicionales (Cummins. Los rresultadosdemostraron la superioridad en ambos aspectos de los motores con inyección electrónica.Se realizó una valoración del tiempo de amortización de la inversión inicial necesaria para utilizar en el parque existenteesta novedosa técnica de la inyección electrónica.Palabras claves: Eficiencia energética, inyección electrónica, consumo de combustible, motores de combustióninterna.__________________________________________________________________Abstract.Taking into consideration the importance of achieving a high efficiency in the internal combustion engines and emissioncontrol of the exhaust gases, this paper deals with economical and environmental advantages of the electronic controlleddiesel engines in heavy-duty trucks, which are used by Cubalse in the transportation. The fuel consumption and the sootemission in Detroit motors (with electronic injection system and Cummins (with traditional system, were studied usingstatistic and experimental methods, and the Detroit proved to be superior in both parameters. The pay back time for theinvestment needed to change the systems of all the existent trucks were calculatedKey words: Energetic efficiency, electronic injection, fuel consumption, internal combustion engine.

40 CFR 86.090-2 - Definitions.

Science.gov (United States)

2010-07-01

... methanol-fueled diesel light-duty vehicle production for those engine families being included in the... 1977 and Later Model Year New Light-Duty Vehicles, Light-Duty Trucks and Heavy-Duty Engines, and for... standard, for a manufacturer which elects to average light-duty vehicles and light-duty trucks together in...

Could Expanded Freight Rail Reduce Air Pollution from Trucks?

Science.gov (United States)

Bickford, E. E.; Holloway, T.; Johnston, M.

2010-12-01

Cars, trucks and trains are a significant source of emissions that impact both climate and air quality on regional to global scales. Diesel vehicles, most used for freight transport, account for 42% of on-road nitrogen oxide emissions, 58% of on-road fine particulate emissions, and 21% of on-road carbon dioxide emissions. With freight tonnage projected to increase 28% by 2018, and freight trucks the fastest growing source of transportation emissions, we evaluate the potential for increased rail capacity to reduce the environmental impacts of trucks. Most widely available mobile source emissions inventories contain insufficient spatial detail to quantify realistic emission scenario options, and none to date have been linked with commodity flow information in a manner appropriate to consider the true potential of rail substitution. To support a truck-to-rail analysis, and other policy assessments requiring roadway-by-roadway analysis, we have developed a freight emissions inventory for the Upper Midwest based on the Federal Highway Administration’s Freight Analysis Framework version 2.2 and the Environmental Protection Agency’s on-road emissions model, Mobile6.2. Using a Geographical Information System (GIS), we developed emissions scenarios for truck-to-rail modal shifts where 95% of freight tonnage on trips longer than 400 miles is shifted off of trucks and onto railways. Scenarios will be analyzed with the Community Multiscale Air Quality (CMAQ) regional model to assess air quality impacts of associated changes. By using well-respected transportation data and realistic assumptions, results from this study have the potential to inform decisions on transportation sustainability, carbon management, public health, and air quality.

Dynamics of dump truck entrance onto the hoist platform of a mine inclined elevator

Energy Technology Data Exchange (ETDEWEB)

Nosyrev, B.A.; Popov, Yu.V.; Mukhutdinov, Sh.D. (Sverdlovskii Gornyi Institut (USSR))

1989-01-01

Analyzes the feasibility of transporting heavy-duty dump trucks along slopes on special platforms in coal surface mines. The platforms are hoisted by winches. Theoretical problems associated with hoisting a loaded platform upwards are analyzed. Problems associated with truck travel in the platform area, its exact positioning and mechanical vibrations of the platform caused by truck movement are discussed. Vibrations of the platform with a loaded truck and vibration amplitudes are analyzed. Five states of the system are evaluated. Methods for prevention of excessive vibrations by optimization of platform design and use of flexible elements are evaluated. Optimum speed of truck movement for platform entering is recommended.

Diesel Emission Control -- Sulfur Effects (DECSE) Program; Phase I Interim Date Report No. 3: Diesel Fuel Sulfur Effects on Particulate Matter Emissions

Energy Technology Data Exchange (ETDEWEB)

DOE; ORNL; NREL; EMA; MECA

1999-11-15

The Diesel Emission Control-Sulfur Effects (DECSE) is a joint government/industry program to determine the impact of diesel fuel sulfur levels on emission control systems whose use could lower emissions of nitrogen oxides (NO{sub x}) and particulate matter (PM) from on-highway trucks in the 2002--2004 model years. Phase 1 of the program was developed with the following objectives in mind: (1) evaluate the effects of varying the level of sulfur content in the fuel on the emission reduction performance of four emission control technologies; and (2) measure and compare the effects of up to 250 hours of aging on selected devices for multiple levels of fuel sulfur content. This interim report covers the effects of diesel fuel sulfur level on particulate matter emissions for four technologies.

Diesel fumes do kill: a case of fatal carbon monoxide poisoning directly attributed to diesel fuel exhaust with a 10-year retrospective case and literature review*.

Science.gov (United States)

Griffin, Sean M; Ward, Michael K; Terrell, Andrea R; Stewart, Donna

2008-09-01

While it is known that diesel fuel combustion engines produce much lower concentrations of carbon monoxide (CO) than gasoline engines, these emissions could certainly generate lethal ambient concentrations given a sufficient amount of time in an enclosed space and under suitable environmental conditions. The authors report a case of CO poisoning which was initially referred for autopsy as a presumed natural death of a truck driver found in the secure cab of a running diesel tractor trailer truck. Completion of the preliminary investigation ascribed death to complications of ischemic heart disease (IHD), pending toxicological analysis that included quantification of CO. When the toxicology results showed lethal blood COHbg, the cause of death was re-certified as CO intoxication secondary to inhalation of (diesel) vehicular exhaust fumes. Because of the unique source of fatal CO intoxication in this case, the contributory IHD and the possible contaminants in the putrefied blood, a 10-year retrospective review was conducted on all nonfire related CO deaths autopsied (n = 94) at the Office of the Chief Medical Examiner in Louisville, KY from 1994 to 2003. For validation of the COHbg detection method used by the Kentucky Office of Forensic Toxicology (KYOFT), blood samples from these cases along with controls were submitted to three laboratories using various analytical methods yielding no statistically significant differences. Lastly, an extensive literature review produced no scientifically reported cases of fatal CO poisoning attributed to diesel fuel exhaust.

Real-world exhaust temperature profiles of on-road heavy-duty diesel vehicles equipped with selective catalytic reduction.

Science.gov (United States)

Boriboonsomsin, Kanok; Durbin, Thomas; Scora, George; Johnson, Kent; Sandez, Daniel; Vu, Alexander; Jiang, Yu; Burnette, Andrew; Yoon, Seungju; Collins, John; Dai, Zhen; Fulper, Carl; Kishan, Sandeep; Sabisch, Michael; Jackson, Doug

2018-09-01

On-road heavy-duty diesel vehicles are a major contributor of oxides of nitrogen (NO x ) emissions. In the US, many heavy-duty diesel vehicles employ selective catalytic reduction (SCR) technology to meet the 2010 emission standard for NO x . Typically, SCR needs to be at least 200°C before a significant level of NO x reduction is achieved. However, this SCR temperature requirement may not be met under some real-world operating conditions, such as during cold starts, long idling, or low speed/low engine load driving activities. The frequency of vehicle operation with low SCR temperature varies partly by the vehicle's vocational use. In this study, detailed vehicle and engine activity data were collected from 90 heavy-duty vehicles involved in a range of vocations, including line haul, drayage, construction, agricultural, food distribution, beverage distribution, refuse, public work, and utility repair. The data were used to create real-world SCR temperature and engine load profiles and identify the fraction of vehicle operating time that SCR may not be as effective for NO x control. It is found that the vehicles participated in this study operate with SCR temperature lower than 200°C for 11-70% of the time depending on their vocation type. This implies that real-world NO x control efficiency could deviate from the control efficiency observed during engine certification. Copyright © 2018 Elsevier B.V. All rights reserved.

40 CFR 86.347-79 - Alternative calculations for diesel engines.

Science.gov (United States)

2010-07-01

... Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test Procedures § 86.347-79 Alternative calculations for diesel engines. (a) This section applies to Diesel engines only. Gasoline-fueled engines must use the calculations in § 86.345. (b) For Diesel engines, the...

Emissions of toxic pollutants from compressed natural gas and low sulfur diesel-fueled heavy-duty transit buses tested over multiple driving cycles.

Science.gov (United States)

Kado, Norman Y; Okamoto, Robert A; Kuzmicky, Paul A; Kobayashi, Reiko; Ayala, Alberto; Gebel, Michael E; Rieger, Paul L; Maddox, Christine; Zafonte, Leo

2005-10-01

The number of heavy-duty vehicles using alternative fuels such as compressed natural gas (CNG) and new low-sulfur diesel fuel formulations and equipped with after-treatment devices are projected to increase. However, few peer-reviewed studies have characterized the emissions of particulate matter (PM) and other toxic compounds from these vehicles. In this study, chemical and biological analyses were used to characterize the identifiable toxic air pollutants emitted from both CNG and low-sulfur-diesel-fueled heavy-duty transit buses tested on a chassis dynamometer over three transient driving cycles and a steady-state cruise condition. The CNG bus had no after-treatment, and the diesel bus was tested first equipped with an oxidation catalyst (OC) and then with a catalyzed diesel particulate filter (DPF). Emissions were analyzed for PM, volatile organic compounds (VOCs; determined on-site), polycyclic aromatic hydrocarbons (PAHs), and mutagenic activity. The 2000 model year CNG-fueled vehicle had the highest emissions of 1,3-butadiene, benzene, and carbonyls (e.g., formaldehyde) of the three vehicle configurations tested in this study. The 1998 model year diesel bus equipped with an OC and fueled with low-sulfur diesel had the highest emission rates of PM and PAHs. The highest specific mutagenic activities (revertants/microg PM, or potency) and the highest mutagen emission rates (revertants/mi) were from the CNG bus in strain TA98 tested over the New York Bus (NYB) driving cycle. The 1998 model year diesel bus with DPF had the lowest VOCs, PAH, and mutagenic activity emission. In general, the NYB driving cycle had the highest emission rates (g/mi), and the Urban Dynamometer Driving Schedule (UDDS) had the lowest emission rates for all toxics tested over the three transient test cycles investigated. Also, transient emissions were, in general, higher than steady-state emissions. The emissions of toxic compounds from an in-use CNG transit bus (without an oxidation

PERBEDAAN RISK PRIORITY NUMBER DALAM FAILURE MODE AND EFFECTS ANALYSIS FMEA SISTEM ALAT BERAT HEAVY DUTY TRUCK HD 785-7

Directory of Open Access Journals (Sweden)

M. Syafwansyah Effendi

2015-04-01

Full Text Available Failure Mode and Efect Analysis (FMEA adalah jenis desain dan teknologi untuk menganalisis keandalan pencegahan, yang merupakan formula yang sistematis terstruktur untuk mengidentifikasi modus kerusakan yang potensial dalam desain atau manufaktur, kemudian mempelajari pengaruh kerusakan pada sistem, kemudian mengambil langkah-langkah yang diperlukan untuk mengkoreksi dan sebagai metode pencegahan sementara yang mengarah pada masalah dalam sistam keandalan. Secara tradisional, menggunakan teknologi dari FMEA adalah untuk memperbaiki keputusan dalam urutan dari besar Risk Priority Number (RPN ke yang lebih kecil State of art permasalahan yang mendasar dari RPN Failure and Efect Analysis adalah bagaimana menerapkannya dalam cakupan cukup luas dalam berbagai bidang sebagai alat atau metode yang bermanfaat untuk membantu menjustifikasi pengambilan suatu keputusan dalam menentukan keandalan suatu sistem. Dari penelitian-penelitian yang sudah dilakukan penerapan Model ini banyak dilakukan di lingkungan industri, dan belum ada yang mengapilikasikannya dalam menganalisa mode kegagalan sistem pada peralatan Berat terutama yang dioperasikan disektor pertambangan. Sehingga pada penelitian ini, adalah perlu untuk menguji apakah ada Perbedaan Dalam Risk Priority Number Failure Mode and Effects Analysis Pada Unit Sistem Alat Berat Heavy Duty Truck HD 785-7. Data diambil dari data History Preventive Maintanance pada sebuah perusahaan tambang di Kalimantan Selatan, selama periode 5 tahun. Unit yang diuji nilai RPN dan sistem adalah Mine Truck Heavy Duty Truck HD 785-7 sebagai sampel diambil 10 unit. Dari data tersebut nilai RPN dihitung masing-masing sistem. Selanjutnya data olahan tersebut di uji dengan uji ANOVA, dengan menggunakan uji F selanjutnya ilakukan analisis untuk setiap kelompok rata-rata atau pasangan rata-rata. Pengujian data dengan menggunakan uji Posteriori (Post Hoc uji Tukey HSD dan Duncan untuk melihat sistem yang mana dari 15 sistem yang rata

Heavy metal and antibiotic resistance of Acinetobacter spp. isolated from diesel fuel polluted

Directory of Open Access Journals (Sweden)

Kais Kassim Ghaima

2018-04-01

Full Text Available Heavy metals pollution of soil and wastewater is a global problem that threatens the environment as they are not degraded or removed and the potential threat to human health comes from the multiple resistances to heavy metals and antibiotics among bacterial populations. The present study was aimed to isolate and identify multiple metal/antibiotic resistant Acinetobacter spp. from diesel fuel polluted soil of Al-Dora, Baghdad, Iraq. Initially, a total of 24 bacterial cultures (coded KNZ–1 to KNZ–24 were isolated and identified up to genus level as Acinetobacter by morphological, physiological and biochemical characteristics. Screening of heavy metals resistant Acinetobacter were conducted by streaking the isolates on nutrient agar plates supplemented with different concentrations: 10, 25, 50 and 100mg/L of the three heavy metals; Hg2+, Cd2+ and Pb2+. Out of 24 isolates, 6 (25% isolates (KNZ–3, KNZ–5, KNZ–8, KNZ–12, KNZ–16 and KNZ–21 were selected as a multiple heavy metal resistant (MHMR Acinetobacter with maximum tolerable concentrations (MTCs; 100–200mg/L for Hg2+, 300-600mg/L for Cd2+ and 100–300mg/L for Pb2+. Antibiotic resistance pattern of the selected MHMR isolates was determined by Kirby-Bauer disc diffusion method against 12 different antibiotics belonging to 7 classes. Out of 6 isolates, 4 isolates were multidrug resistance (MDR with varying degrees. Among them isolate, KNZ–16 showed a wide range of resistance to all tested antibiotics except Levofloxacin and Imipenem. It was concluded that dual resistant Acinetobacter is useful in the bioremediation of environments polluted with heavy metals especially the biodegradation of organic pollutants.

Effect of biodiesel fuel on "real-world", nonroad heavy duty diesel engine particulate matter emissions, composition and cytotoxicity.

Science.gov (United States)

Martin, Nathan; Lombard, Melissa; Jensen, Kirk R; Kelley, Patrick; Pratt, Tara; Traviss, Nora

2017-05-15

Biodiesel is regarded by many as a "greener" alternative fuel to petroleum diesel with potentially lower health risk. However, recent studies examining biodiesel particulate matter (PM) characteristics and health effects are contradictive, and typically utilize PM generated by passenger car engines in laboratory settings. There is a critical need to analyze diesel and biodiesel PM generated in a "real-world" setting where heavy duty-diesel (HDD) engines and commercially purchased fuel are utilized. This study compares the mass concentrations, chemical composition and cytotoxicity of real-world PM from combustion of both petroleum diesel and a waste grease 20% biodiesel blend (B20) at a community recycling center operating HDD nonroad equipment. PM was analyzed for metals, elemental/organic carbon (EC/OC), polycyclic aromatic hydrocarbons (PAHs), and nitro-polycyclic aromatic hydrocarbons (N-PAHs). Cytotoxicity in a human lung epithelial cell line (BEAS-2B) following 24h exposure to the real-world particles was also evaluated. On average, higher concentrations for both EC and OC were measured in diesel PM. B20 PM contained significantly higher levels of Cu and Mo whereas diesel PM contained significantly higher concentrations of Pb. Principal component analysis determined Mo, Cu, and Ni were the metals with the greatest loading factor, suggesting a unique pattern related to the B20 fuel source. Total PAH concentration during diesel fuel use was 1.9 times higher than during B20 operations; however, total N-PAH concentration was 3.3 times higher during B20 use. Diesel PM cytotoxicity was 8.5 times higher than B20 PM (pengine sources of metals, PAH and N-PAH species, comparing tailpipe PM vs. PM collected inside the equipment cabin. Results suggest PM generated from burning petroleum diesel in nonroad engines may be more harmful to human health, but the links between exposure, composition and toxicity are not straightforward. Copyright © 2016 Elsevier B.V. All rights

Effects of Variation in Truck Factor on Pavement Performance in Pakistan

Directory of Open Access Journals (Sweden)

Rabia Chaudry

2013-01-01

Full Text Available Seasonal variation coupled with heavy axle loading is the key factor in rapid road deterioration in Pakistan. The serviceability loss is further accelerated by the fact that truck drivers and owners consider overloading as a profitable practice unaware of the adverse effects of this practice. Weigh-in-motion data from two stations located between two major cities of Pakistan (Peshawar and Rawalpindi on Grand Trunk Road (N-5 were collected and analyzed. Analysis of variance and comparison of actual and designed truck factor were performed to identify the most damaging axle truck type. It was found that axle truck type 3 (single/tandem axle is most damaging among all truck types. The actual truck factor for axle truck type 3 is 6.4 times greater than design truck factor. Regression expressions of different forms were also investigated to determine the relationship between truck factor and gross vehicular weight for the specified truck types. An optimum generalization strategy was used to prevent over-generalization and ensure accuracy. For data analysis, 75% of data was used to develop regression models and remaining 25% was to validate those models. The results show that the polynomial expressions performed best and provide a robust relationship that can be employed by the highway authorities to estimate truck factor from gross vehicular weight with a high degree of confidence. It was also observed that damaging effect of various types of trucks was very severe and quite high.

The effects of emission control strategies on light-absorbing carbon emissions from a modern heavy-duty diesel engine.

Science.gov (United States)

Robinson, Michael A; Olson, Michael R; Liu, Z Gerald; Schauer, James J

2015-06-01

Control of atmospheric black carbon (BC) and brown carbon (BrC) has been proposed as an important pathway to climate change mitigation, but sources of BC and BrC are still not well understood. In order to better identify the role of modern heavy-duty diesel engines on the production of BC and BrC, emissions from a heavy-duty diesel engine operating with different emission control strategies were examined using a source dilution sampling system. The effect of a diesel oxidation catalyst (DOC) and diesel particulate filter (DPF) on light-absorbing carbon (LAC) was evaluated at three steady-state engine operation modes: idle, 50% speed and load, and 100% speed and load. LAC was measured with four different engine configurations: engine out, DOC out, DPF out, and engine out with an altered combustion calibration. BC and BrC emission rates were measured with the Aethalometer (AE-31). EC and BC emission rates normalized to the mass of CO₂emitted increased with increasing engine speed and load. Emission rates normalized to brake-specific work did not exhibit similar trends with speed and load, but rather the highest emission rate was measured at idle. EC and OC emissions were reduced by 99% when the DOC and DPF architecture was applied. The application of a DPF was equally effective at removing 99% of the BC fraction of PM, proving to be an important control strategy for both LAC and PM. BC emissions were unexpectedly increased across the DOC, seemingly due to a change aerosol optical properties. Removal of exhaust gas recirculation (EGR) flow due to simulated EGR cooler failure caused a large increase in OC and BrC emission rates at idle, but had limited influence during high load operation. LAC emissions proved to be sensitive to the same control strategies effective at controlling the total mass of diesel PM. In the context of black carbon emissions, very small emission rates of brown carbon were measured over a range of control technologies and engine operating

Metal particle emissions in the exhaust stream of diesel engines: an electron microscope study.

Science.gov (United States)

Liati, Anthi; Schreiber, Daniel; Dimopoulos Eggenschwiler, Panayotis; Arroyo Rojas Dasilva, Yadira

2013-12-17

Scanning electron microscopy and transmission electron microscopy were applied to investigate the morphology, mode of occurrence and chemical composition of metal particles (diesel ash) in the exhaust stream of a small truck outfitted with a typical after-treatment system (a diesel oxidation catalyst (DOC) and a downstream diesel particulate filter (DPF)). Ash consists of Ca-Zn-P-Mg-S-Na-Al-K-phases (lube-oil related), Fe, Cr, Ni, Sn, Pb, Sn (engine wear), and Pd (DOC coating). Soot agglomerates of variable sizes (1-5 μm, exceptionally 13 μm), rarely engine wear and escape into the atmosphere.

The Problem of Multiple Criteria Selection of the Surface Mining Haul Trucks

Science.gov (United States)

Bodziony, Przemysław; Kasztelewicz, Zbigniew; Sawicki, Piotr

2016-06-01

Vehicle transport is a dominant type of technological processes in rock mines, and its profit ability is strictly dependent on overall cost of its exploitation, especially on diesel oil consumption. Thus, a rational design of transportation system based on haul trucks should result from thorough analysis of technical and economic issues, including both cost of purchase and its further exploitation, having a crucial impact on the cost of minerals extraction. Moreover, off-highway trucks should be selected with respect to all specific exploitation conditions and even the user's preferences and experience. In this paper a development of universal family of evaluation criteria as well as application of evaluation method for haul truck selection process for a specific exploitation conditions in surface mining have been carried out. The methodology presented in the paper is based on the principles of multiple criteria decision aiding (MCDA) using one of the ranking method, i.e. ELECTRE III. The applied methodology has been allowed for ranking of alternative solution (variants), on the considered set of haul trucks. The result of the research is a universal methodology, and it consequently may be applied in other surface mines with similar exploitation parametres.

Baumot BA-B Diesel Particulate Filter with Pre-Catalyst (ETV Mobile Source Emissions Control Devices) Verification Report

Science.gov (United States)

The Baumot BA-B Diesel Particulate Filter with Pre-Catalyst is a diesel engine retrofit device for light, medium, and heavy heavy-duty diesel on-highway engines for use with commercial ultra-low-sulfur diesel (ULSD) fuel. The BA-B particulate filter is composed of a pre-catalyst ...

Optimal Sizing and Control Strategy Design for Heavy Hybrid Electric Truck

Directory of Open Access Journals (Sweden)

Yuan Zou

2012-01-01

Full Text Available Due to the complexity of the hybrid powertrain, the control is highly involved to improve the collaborations of the different components. For the specific powertrain, the components' sizing just gives the possibility to propel the vehicle and the control will realize the function of the propulsion. Definitely the components' sizing also gives the constraints to the control design, which cause a close coupling between the sizing and control strategy design. This paper presents a parametric study focused on sizing of the powertrain components and optimization of the power split between the engine and electric motor for minimizing the fuel consumption. A framework is put forward to accomplish the optimal sizing and control design for a heavy parallel pre-AMT hybrid truck under the natural driving schedule. The iterative plant-controller combined optimization methodology is adopted to optimize the key parameters of the plant and control strategy simultaneously. A scalable powertrain model based on a bilevel optimization framework is built. Dynamic programming is applied to find the optimal control in the inner loop with a prescribed cycle. The parameters are optimized in the outer loop. The results are analysed and the optimal sizing and control strategy are achieved simultaneously.

Case Study: Natural Gas Regional Transport Trucks

Energy Technology Data Exchange (ETDEWEB)

Laughlin, M.; Burnham, A.

2016-08-01

Learn about Ryder System, Inc.'s experience in deploying nearly 200 CNG and LNG heavy-duty trucks and construction and operation of L/CNG stations using ARRA funds. Using natural gas in its fleet, Ryder mitigated the effects of volatile fuel pricing and reduced lifecycle GHGs by 20% and petroleum by 99%.

Experimental and numerical assessment of on-road diesel and biodiesel emissions

Energy Technology Data Exchange (ETDEWEB)

West, B.H.; Storey, J.M.; Lewis, S.A.; Devault, G.L.; Green, J.B. [Oak Ridge National Lab., TN (United States); Sluder, C.S.; Hodgson, J.W.; Moore, B.L. [Univ. of Tennessee, Knoxville, TN (United States)

1997-12-31

The Federal Highway Administration`s TRAF-series of models use modal data to estimate fuel consumption and emissions for different traffic scenarios. A process for producing data-based modal models from road and dynamometer measurements has been developed and applied to a number of light-duty gasoline vehicles for the FHWA. The resulting models, or lookup tables, provide emissions and fuel consumption as functions of vehicle speed and acceleration. Surface plots of the data provide a valuable visual benchmark of the emissions characteristics of the vehicles. Due to the potential fuel savings in the light-duty sector via introduction of diesels, and the concomitant growing interest in diesel engine emissions, the measurement methodology has been extended under DOE sponsorship to include a diesel pickup truck running a variety of fuels, including number 2 diesel fuel, biodiesel, Fischer-Tropsch, and blends.

Appliance of high EGR rates with a short and long route EGR system on a heavy duty diesel engine

NARCIS (Netherlands)

Aken, van M.; Willems, F.P.T.; Jong, de D.J.

2007-01-01

The goal of this work was to investigate the possibilities of applying high EGR rates with low NOx and PM emission levels on a two-stage turbocharged 12 liter heavy duty diesel engine. The EGR is applied by using a long and short route EGR system. For the ESC operating points A25 and C100 EGR is

The effect of rapeseed oil biodiesel fuel on combustion, performance, and the emission formation process within a heavy-duty DI diesel engine

International Nuclear Information System (INIS)

Lešnik, Luka; Biluš, Ignacijo

2016-01-01

Highlights: • Sub-models for parameter determination can be derived using experimental results. • Proposed sub-models can be used for calculation of model parameters. • Biodiesel fuel reduces emissions compared to diesel fuel on full engine load. • Usage of biodiesel fuel slow down the emission formation rate. • Oxygen content in biodiesel fuel decreases the amount of formatted CO emissions. - Abstract: This study presents the influence of biodiesel fuel and blends with mineral diesel fuel on diesel engine performance, the combustion process, and the formation of emissions. The study was conducted numerically and experimentally. The aim of the study was to test the possibility of replacing mineral diesel fuel with biodiesel fuel made from rapeseed oil. Pure biodiesel fuel and three blends of biodiesel fuel with mineral diesel fuel were tested experimentally for that purpose on a heavy-duty bus diesel engine. The engine’s performance, in-cylinder pressure, fuel consumption, and the amount of produced NO_x and CO emissions were monitored during experimental measurements, which were repeated numerically using the AVL BOOST simulation program. New empirical sub-models are proposed for determining a combustion model and emission models parameters. The proposed sub-models allow the determination of necessary combustion and emission model parameters regarding the properties of the tested fuel and the engine speed. When increasing the percentage of biodiesel fuel within the fuel blends, the reduction in engine torque and brake mean effective pressures are obtained for most of the test regimes. The reduction is caused due to the lower calorific value of the biodiesel fuel. Higher oxygen content in biodiesel fuel contributes to a better oxidation process within the combustion chamber when running on pure biodiesel or its blends. Better oxidation further results in a reduction of the formatted carbon and nitrogen oxides. The reduction of carbon emission is also

Effects of biodiesel, engine load and diesel particulate filter on nonvolatile particle number size distributions in heavy-duty diesel engine exhaust

Energy Technology Data Exchange (ETDEWEB)

Young, Li-Hao, E-mail: lhy@mail.cmu.edu.tw [Department of Occupational Safety and Health, China Medical University, 91, Hsueh-Shih Road, Taichung 40402, Taiwan (China); Liou, Yi-Jyun [Department of Occupational Safety and Health, China Medical University, 91, Hsueh-Shih Road, Taichung 40402, Taiwan (China); Cheng, Man-Ting [Department of Environmental Engineering, National Chung Hsing University, 250, Kuo-Kuang Road, Taichung 40254, Taiwan (China); Lu, Jau-Huai [Department of Mechanical Engineering, National Chung Hsing University, 250, Kuo-Kuang Road, Taichung 40254, Taiwan (China); Yang, Hsi-Hsien [Department of Environmental Engineering and Management, Chaoyang University of Technology, 168, Jifeng E. Road, Taichung 41349, Taiwan (China); Tsai, Ying I. [Department of Environmental Engineering and Science, Chia Nan University of Pharmacy and Science, 60, Sec. 1, Erh-Jen Road, Tainan 71710, Taiwan (China); Wang, Lin-Chi [Department of Chemical and Materials Engineering, Cheng Shiu University, 840, Chengcing Road, Kaohsiung 83347, Taiwan (China); Chen, Chung-Bang [Fuel Quality and Engine Performance Research, Refining and Manufacturing Research Institute, Chinese Petroleum Corporation, 217, Minsheng S. Road, Chiayi 60036, Taiwan (China); Lai, Jim-Shoung [Department of Occupational Safety and Health, China Medical University, 91, Hsueh-Shih Road, Taichung 40402, Taiwan (China)

2012-01-15

Highlights: Black-Right-Pointing-Pointer The effects of waste cooking oil biodiesel, engine load and DOC + DPF on nonvolatile particle size distributions in HDDE exhaust. Black-Right-Pointing-Pointer Increasing biodiesel blends cause slight decreases in the total particle number concentrations and negligible changes in size distributions. Black-Right-Pointing-Pointer Increasing load results in modest increases in both the total particle number concentrations and sizes. Black-Right-Pointing-Pointer The effects of semivolatile materials are strongest at idle, during which nonvolatile cores <16 nm were observed. Black-Right-Pointing-Pointer The DOC + DPF shows remarkable filtration efficiency for both the core and soot particles, irrespective of biodiesel blend and load. - Abstract: Diesel engine exhaust contains large numbers of submicrometer particles that degrade air quality and human health. This study examines the number emission characteristics of 10-1000 nm nonvolatile particles from a heavy-duty diesel engine, operating with various waste cooking oil biodiesel blends (B2, B10 and B20), engine loads (0%, 25%, 50% and 75%) and a diesel oxidation catalyst plus diesel particulate filter (DOC + DPF) under steady modes. For a given load, the total particle number concentrations (N{sub TOT}) decrease slightly, while the mode diameters show negligible changes with increasing biodiesel blends. For a given biodiesel blend, both the N{sub TOT} and mode diameters increase modestly with increasing load of above 25%. The N{sub TOT} at idle are highest and their size distributions are strongly affected by condensation and possible nucleation of semivolatile materials. Nonvolatile cores of diameters less than 16 nm are only observed at idle mode. The DOC + DPF shows remarkable filtration efficiency for both the core and soot particles, irrespective of the biodiesel blend and engine load under study. The N{sub TOT} post the DOC + DPF are comparable to typical ambient levels of

Alternative-fueled truck demonstration natural gas program: Caterpillar G3406LE development and demonstration

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-06-01

In 1990, the California Energy Commission, the South Coast Air Quality Management District, and the Southern California Gas Company joined together to sponsor the development and demonstration of compressed natural gas engines for Class 8 heavy-duty line-haul trucking applications. This program became part of an overall Alternative-Fueled Truck Demonstration Program, with the goal of advancing the technological development of alternative-fueled engines. The demonstration showed natural gas to be a technically viable fuel for Class 8 truck engines.

Characteristics of On-road Diesel Vehicles: Black Carbon Emissions in Chinese Cities Based on Portable Emissions Measurement.

Science.gov (United States)

Zheng, Xuan; Wu, Ye; Jiang, Jingkun; Zhang, Shaojun; Liu, Huan; Song, Shaojie; Li, Zhenhua; Fan, Xiaoxiao; Fu, Lixin; Hao, Jiming

2015-11-17

Black carbon (BC) emissions from heavy-duty diesel vehicles (HDDVs) are rarely continuously measured using portable emission measurement systems (PEMSs). In this study, we utilize a PEMS to obtain real-world BC emission profiles for 25 HDDVs in China. The average fuel-based BC emissions of HDDVs certified according to Euro II, III, IV, and V standards are 2224 ± 251, 612 ± 740, 453 ± 584, and 152 ± 3 mg kg(-1), respectively. Notably, HDDVs adopting mechanical pump engines had significantly higher BC emissions than those equipped with electronic injection engines. Applying the useful features of PEMSs, we can relate instantaneous BC emissions to driving conditions using an operating mode binning methodology, and the average emission rates for Euro II to Euro IV diesel trucks can be constructed. From a macroscopic perspective, we observe that average speed is a significant factor affecting BC emissions and is well correlated with distance-based emissions (R(2) = 0.71). Therefore, the average fuel-based and distance-based BC emissions on congested roads are 40 and 125% higher than those on freeways. These results should be taken into consideration in future emission inventory studies.

Computational study of the effect of different injection angle on heavy duty diesel engine combustion

Directory of Open Access Journals (Sweden)

Ranjbar Ali Akbar

2009-01-01

Full Text Available Diesel engines exhausting gaseous emission and particulate matter have long been regarded as one of the major air pollution sources, particularly in metropolitan areas, and have been a source of serious public concern for a long time. The choosing various injection strategies is not only motivated by cost reduction but is also one of the potentially effective techniques to reduce exhaust emission from diesel engines. The purpose of this study is to investigate the effect of different injection angles on a heavy duty diesel engine and emission characteristics. The varieties of injection angle were simulated and the emissions like soot and NO is calculated. The comparison between the different injection strategies was also investigated. A combustion chamber for three injection strategies (injection direction with angles of α=67.5, 70, and 72.5 degree was simulated. The comparative study involving rate of heat release, in-cylinder temperature, in-cylinder pressure, NO and soot emissions were also reported for different injection strategies. The case of α=70 is optimum because in this manner the emissions are lower in almost most of crank angle than two other cases and the in-cylinder pressure, which is a representation of engine power, is higher than in the case of α=67.5 and just a little lower than in the case of α=72.5.

Alcohols/Ethers as Oxygenates in Diesel Fuel: Properties of Blended Fuels and Evaluation of Practiacl Experiences

Energy Technology Data Exchange (ETDEWEB)

Nylund, N.; Aakko, P. [TEC Trans Energy Consulting Ltd (Finland); Niemi, S.; Paanu, T. [Turku Polytechnic (Finland); Berg, R. [Befri Konsult (Sweden)

2005-03-15

is also of importance. So far, no engine manufacturers have indicated they will extend warranty coverage to their equipment when operating with E-diesel. They believe there are simply too many unanswered questions as well as the potential for liability exposure due to the increased flammability range of E-diesel. The reports on field tests with oxygenated diesel fuels are rather scarce, especially reports on recent tests. There are, however, some reports available on engine tests and tests with trucks, buses and even off-road equipment. Most of the available test results identified fuel economy and cost as the only appreciable differences between E-diesel and conventional diesel fuel. Most emissions tests with heavy-duty engines confirm the effect of a substantial reduction in PM when running with E-diesel. The typical range for PM reduction is 20 -- 40 %. Most studies also report reduced NOx emissions. Earlier, there were a lot of activities with E-diesel in Sweden. For the time being, California and Brazil are leading the development of E-diesel.

Alcohols/Ethers as Oxygenates in Diesel Fuel: Properties of Blended Fuels and Evaluation of Practiacl Experiences

Energy Technology Data Exchange (ETDEWEB)

Nylund, N; Aakko, P [TEC Trans Energy Consulting Ltd (Finland); Niemi, S; Paanu, T [Turku Polytechnic (Finland); Berg, R [Befri Konsult (Sweden)

2005-03-15

of importance. So far, no engine manufacturers have indicated they will extend warranty coverage to their equipment when operating with E-diesel. They believe there are simply too many unanswered questions as well as the potential for liability exposure due to the increased flammability range of E-diesel. The reports on field tests with oxygenated diesel fuels are rather scarce, especially reports on recent tests. There are, however, some reports available on engine tests and tests with trucks, buses and even off-road equipment. Most of the available test results identified fuel economy and cost as the only appreciable differences between E-diesel and conventional diesel fuel. Most emissions tests with heavy-duty engines confirm the effect of a substantial reduction in PM when running with E-diesel. The typical range for PM reduction is 20 -- 40 %. Most studies also report reduced NOx emissions. Earlier, there were a lot of activities with E-diesel in Sweden. For the time being, California and Brazil are leading the development of E-diesel.

Assessment of diesel particulate matter exposure in the workplace: freight terminals†

Science.gov (United States)

Sheesley, Rebecca J.; Schauer, James J.; Smith, Thomas J.; Garshick, Eric; Laden, Francine; Marr, Linsey C.; Molina, Luisa T.

2008-01-01

A large study has been undertaken to assess the exposure to diesel exhaust within diesel trucking terminals. A critical component of this assessment is an analysis of the variation in carbonaceous particulate matter (PM) across trucking terminal locations; consistency in the primary sources can be effectively tracked by analyzing trends in elemental carbon (EC) and organic molecular marker concentrations. Ambient samples were collected at yard, dock and repair shop work stations in 7 terminals in the USA and 1 in Mexico. Concentrations of EC ranged from 0.2 to 12 μg m−3 among the terminals, which corresponds to the range seen in the concentration of summed hopanes (0.5 to 20.5 ng m−3). However, when chemical mass balance (CMB) source apportionment results were presented as percent contribution to organic carbon (OC) concentrations, the contribution of mobile sources to OC are similar among the terminals in different cities. The average mobile source percent contribution to OC was 75.3 ± 17.1% for truck repair shops, 65.4 ± 20.4% for the docks and 38.4 ± 9.5% for the terminal yard samples. A relatively consistent mobile source impact was present at all the terminals only when considering percentage of total OC concentrations, not in terms of absolute concentrations. PMID:18392272

Test/QA plan for the verification testing of selective catalytic reduction control technologies for highway, nonroad use heavy-duty diesel engines

Science.gov (United States)

This ETV test/QA plan for heavy-duty diesel engine testing at the Southwest Research Institute’s Department of Emissions Research (DER) describes how the Federal Test Procedure (FTP), as listed in 40 CFR Part 86 for highway engines and 40 CFR Part 89 for nonroad engines, will be ...

Temperature and driving cycle influence SVOC emissions from (bio-) diesel trucks

Data.gov (United States)

U.S. Environmental Protection Agency — The present study examines the effects of fuel (an ultra-low sulfur diesel [ULSD] versus a 20% v/v soy-based biodiesel—80% v/v petroleum blend [B20]), temperature,...

Occupational exposure to diesel exhaust fumes

International Nuclear Information System (INIS)

Wheatley, A. D.; Sadhra, S.

2004-01-01

There is currently no OEL for diesel fumes in the UK. This study reports parallel measurements of airborne levels of diesel fume pollutants in nine distribution depots where diesel powered fork-lift trucks (FLTs) were in use. Correlations between individual pollutants are assessed as well as their spatial distribution. Samples were collected on board FLTs and at background positions at nine distribution depots. Substances measured and the range of exposures by site were: respirable dust (n = 76) GM ≤ 80-179 μg/m 3 ; elemental carbon (n = 79) GM = 7-55 μg/m 3 ; organic carbon (n = 79) GM 11-69 μg/m 3 ; ultrafine particles (n = 17) range = 58-231 x 10 3 particles/cm 3 ; selected particulate phase polycyclic aromatic hydrocarbons (PAHs) (n - 14) range = 6-37 ng/m 3 . In addition, a tracer method based on ultrafine particle measurements was used to estimate the spatial distribution of total carbon and PAHs at the sites monitored. The spatial distribution was found to be reasonably uniform. Major diesel fume aerosol components were, in general, well correlated (r = 0.62-0.97). CO 2 measurements were also made and found to be below the HSE guideline of 1000 p.p.m., with most levels below 600 p.p.m. (Author)

Near-road air pollution impacts of goods movement in communities adjacent to the Ports of Los Angeles and Long Beach

Science.gov (United States)

Kozawa, Kathleen H.; Fruin, Scott A.; Winer, Arthur M.

A mobile platform was outfitted with real-time instruments to spatially characterize pollution concentrations in communities adjacent to the Ports of Los Angeles and Long Beach, communities heavily impacted by emissions related to dieselized goods movement, with the highest localized air pollution impacts due to heavy-duty diesel trucks (HDDT). Measurements were conducted in the winter and summer of 2007 on fixed routes driven both morning and afternoon. Diesel-related pollutant concentrations such as black carbon, nitric oxide, ultrafine particles, and particle-bound polycyclic aromatic hydrocarbons were frequently elevated two to five times within 150 m downwind of freeways (compared to more than 150 m) and up to two times within 150 m downwind of arterial roads with significant amounts of diesel traffic. While wind direction was the dominant factor associated with downwind impacts, steady and consistent wind direction was not required to produce; high impacts were observed when a given area was downwind of a major roadway for any significant fraction of time. This suggests elevated pollution impacts downwind of freeways and of busy arterials are continuously occurring on one side of the road or the other, depending on wind direction. The diesel truck traffic in the area studied was high, with more than 2000 trucks per peak hour on the freeway and two- to six-hundred trucks per hour on the arterial roads studied. These results suggest that similarly-frequent impacts occur throughout urban areas in rough proportion to diesel truck traffic fractions. Thus, persons living or working near and downwind of busy roadways can have several-fold higher exposures to diesel vehicle-related pollution than would be predicted by ambient measurements in non-impacted locations.

New approach for reduction of diesel consumption by comparing different mining haulage configurations.

Science.gov (United States)

Rodovalho, Edmo da Cunha; Lima, Hernani Mota; de Tomi, Giorgio

2016-05-01

The mining operations of loading and haulage have an energy source that is highly dependent on fossil fuels. In mining companies that select trucks for haulage, this input is the main component of mining costs. How can the impact of the operational aspects on the diesel consumption of haulage operations in surface mines be assessed? There are many studies relating the consumption of fuel trucks to several variables, but a methodology that prioritizes higher-impact variables under each specific condition is not available. Generic models may not apply to all operational settings presented in the mining industry. This study aims to create a method of analysis, identification, and prioritization of variables related to fuel consumption of haul trucks in open pit mines. For this purpose, statistical analysis techniques and mathematical modelling tools using multiple linear regressions will be applied. The model is shown to be suitable because the results generate a good description of the fuel consumption behaviour. In the practical application of the method, the reduction of diesel consumption reached 10%. The implementation requires no large-scale investments or very long deadlines and can be applied to mining haulage operations in other settings. Copyright © 2016 Elsevier Ltd. All rights reserved.

Detroit Diesel Engine Technology for Light Duty Truck Applications - DELTA Engine Update

Energy Technology Data Exchange (ETDEWEB)

Freese, Charlie

2000-08-20

The early generation of the DELTA engine has been thoroughly tested and characterized in the virtual lab, during engine dynamometer testing, and on light duty trucks for personal transportation. This paper provides an up-to-date account of program findings. Further, the next generation engine design and future program plans will be briefly presented.

An analysis of the lifestyle risk factors for long-distance truck drivers / Barend Koortzen von Wielligh

OpenAIRE

Von Wielligh, Barend Koortzen

2014-01-01

The Road Freight Industry accounts for 1 to 5 percent of most countries GDP (AECOM International Development, 2011). According to e-Natis there was 321 056 Trucks (Heavy load Vehicle GVM > 3500 kg) in South Africa by November 2009 (Arrive Alive, 2009). This relative big industry, according to the statistics, influences most other industries value chains. Vehicles are driven by trucks drivers, making driving trucks their living. These drivers have their own lifestyles and ways that they go abo...

Emissions of black carbon and co-pollutants emitted from diesel vehicles in the Mexico City Metropolitan Area

Science.gov (United States)

Zavala, Miguel; Molina, Luisa T.; Fortner, Edward; Knighton, Berk; Herndon, Scott; Yacovitch, Tara; Floerchinger, Cody; Roscioli, Joseph; Kolb, Charles; Mejia, Jose Antonio; Sarmiento, Jorge; Paramo, Victor Hugo; Zirath, Sergio; Jazcilevich, Aron

2014-05-01

Black carbon emitted from freight, public transport, and heavy duty trucks sources is linked with adverse effects on human health. In addition, the control of emissions of black carbon, an important short-lived climate forcing agent (SLCF), has recently been considered as one of the key strategies for mitigating regional near-term climate change. Despite the availability of new emissions control technologies for reducing emissions from diesel-powered mobile sources, their introduction is still not widespread in many urban areas and there is a need to characterize real-world emission rates of black carbon from this key source. The emissions of black carbon, organic carbon, and other gaseous and particle pollutants from diesel-powered mobile sources in Mexico were characterized by deploying a mobile laboratory equipped with real-time instrumentation in Mexico City as part of the SLCFs-Mexico 2013 project. From February 25-28 of 2013 the emissions from selected diesel-powered vehicles were measured in both controlled experiments and real-world on-road driving conditions. Sampled vehicles had several emissions levels technologies, including: EPA98, EPA03, EPA04, EURO3-5, and Hybrid. All vehicles were sampled using diesel fuel and several vehicles were measured using both diesel and biodiesel fuels. Additional measurements included the use of a remote sensing unit for the co-sampling of all tested vehicles, and the installation and operation of a Portable Emissions Measurements System (PEMS) for the measurement of emissions from a test vehicle. We will present inter-comparisons of the emission factors obtained among the various vehicle technologies that were sampled during the experiment as well as the inter-comparison of results from the various sampling platforms. The results can be used to

49 CFR 399.207 - Truck and truck-tractor access requirements.

Science.gov (United States)

2010-10-01

.... Exception. If air and electrical connections necessary to couple or uncouple a truck-tractor from a trailer... 49 Transportation 5 2010-10-01 2010-10-01 false Truck and truck-tractor access requirements. 399... Vehicles § 399.207 Truck and truck-tractor access requirements. (a) General rule. Any person entering or...

Carbonaceous composition changes of heavy-duty diesel engine particles in relation to biodiesels, aftertreatments and engine loads

Energy Technology Data Exchange (ETDEWEB)

Cheng, Man-Ting; Chen, Hsun-Jung [Department of Environmental Engineering, National Chung Hsing University, 250 Kuo-Kuang Road, Taichung 40254, Taiwan (China); Young, Li-Hao, E-mail: lhy@mail.cmu.edu.tw [Department of Occupational Safety and Health, China Medical University, 91 Hsueh-Shih Road, Taichung 40402, Taiwan (China); Yang, Hsi-Hsien [Department of Environmental Engineering and Management, Chaoyang University of Technology, 168, Jifeng E. Road, Wufeng District, Taichung 41349, Taiwan (China); Tsai, Ying I. [Department of Environmental Engineering and Science, Chia Nan University of Pharmacy and Science, 60, Sec. 1, Erren Rd., Rende District, Tainan 71710, Taiwan (China); Wang, Lin-Chi [Department of Civil Engineering and Geomatics, Cheng Shiu University, 840, Chengcing Road, Niaosong District, Kaohsiung 83347, Taiwan (China); Lu, Jau-Huai [Department of Mechanical Engineering, National Chung Hsing University, 250 Kuo-Kuang Road, Taichung 40254, Taiwan (China); Chen, Chung-Bang [Fuel Quality and Engine Performance Research, Refining and Manufacturing Research Institute, Chinese Petroleum Corporation, 217, Minsheng S. Road, West District, Chiayi 60051, Taiwan (China)

2015-10-30

Highlights: • We study particulate OC and EC under 3 fuels, 2 aftertreatments and 4 engine loads. • Negligible to minor OC and EC changes with low, ultralow sulfur and 10% biodiesels. • Moderate reductions of EC and particularly OC from diesel oxidation catalyst (DOC). • Large reductions of OC and particularly EC from DOC plus diesel particulate filter. • Highest at idle, whereas OC decreases but EC increases from low to high load. - Abstract: Three biodiesels and two aftertreatments were tested on a heavy-duty diesel engine under the US FTP transient cycle and additional four steady engine loads. The objective was to examine their effects on the gaseous and particulate emissions, with emphasis given to the organic and elemental carbon (OC and EC) in the total particulate matter. Negligible differences were observed between the low-sulfur (B1S50) and ultralow-sulfur (B1S10) biodiesels, whereas small reductions of OC were identified with the 10% biodiesel blend (B10). The use of diesel oxidation catalyst (DOC1) showed moderate reductions of EC and particularly OC, resulting in the OC/EC ratio well below unity. The use of DOC plus diesel particulate filter (DOC2+DPF) yielded substantial reductions of OC and particularly EC, resulting in the OC/EC ratio well above unity. The OC/EC ratios were substantially above unity at idle and low load, whereas below unity at medium and high load. The above changes in particulate OC and EC are discussed with respect to the fuel content, pollutant removal mechanisms and engine combustion conditions. Overall, the present study shows that the carbonaceous composition of PM could change drastically with engine load and aftertreatments, and to a lesser extent with the biodiesels under study.

Carbonaceous composition changes of heavy-duty diesel engine particles in relation to biodiesels, aftertreatments and engine loads

International Nuclear Information System (INIS)

Cheng, Man-Ting; Chen, Hsun-Jung; Young, Li-Hao; Yang, Hsi-Hsien; Tsai, Ying I.; Wang, Lin-Chi; Lu, Jau-Huai; Chen, Chung-Bang

2015-01-01

Highlights: • We study particulate OC and EC under 3 fuels, 2 aftertreatments and 4 engine loads. • Negligible to minor OC and EC changes with low, ultralow sulfur and 10% biodiesels. • Moderate reductions of EC and particularly OC from diesel oxidation catalyst (DOC). • Large reductions of OC and particularly EC from DOC plus diesel particulate filter. • Highest at idle, whereas OC decreases but EC increases from low to high load. - Abstract: Three biodiesels and two aftertreatments were tested on a heavy-duty diesel engine under the US FTP transient cycle and additional four steady engine loads. The objective was to examine their effects on the gaseous and particulate emissions, with emphasis given to the organic and elemental carbon (OC and EC) in the total particulate matter. Negligible differences were observed between the low-sulfur (B1S50) and ultralow-sulfur (B1S10) biodiesels, whereas small reductions of OC were identified with the 10% biodiesel blend (B10). The use of diesel oxidation catalyst (DOC1) showed moderate reductions of EC and particularly OC, resulting in the OC/EC ratio well below unity. The use of DOC plus diesel particulate filter (DOC2+DPF) yielded substantial reductions of OC and particularly EC, resulting in the OC/EC ratio well above unity. The OC/EC ratios were substantially above unity at idle and low load, whereas below unity at medium and high load. The above changes in particulate OC and EC are discussed with respect to the fuel content, pollutant removal mechanisms and engine combustion conditions. Overall, the present study shows that the carbonaceous composition of PM could change drastically with engine load and aftertreatments, and to a lesser extent with the biodiesels under study

Plug-In Hybrid Urban Delivery Truck Technology Demonstration

Energy Technology Data Exchange (ETDEWEB)

Miyasato, Matt [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States); Impllitti, Joseph [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States); Pascal, Amar [South Coast Air Quality Management District Building Corporation, Diamond Bar, CA (United States)

2015-07-31

The I-710 and CA-60 highways are key transportation corridors in the Southern California region that are heavily used on a daily basis by heavy duty drayage trucks that transport the cargo from the ports to the inland transportation terminals. These terminals, which include store/warehouses, inland-railways, are anywhere from 5 to 50 miles in distance from the ports. The concentrated operation of these drayage vehicles in these corridors has had and will continue to have a significant impact on the air quality in this region whereby significantly impacting the quality of life in the communities surrounding these corridors. To reduce these negative impacts it is critical that zero and near-zero emission technologies be developed and deployed in the region. A potential local market size of up to 46,000 trucks exists in the South Coast Air Basin, based on near- dock drayage trucks and trucks operating on the I-710 freeway. The South Coast Air Quality Management District (SCAQMD), California Air Resources Board (CARB) and Southern California Association of Governments (SCAG) — the agencies responsible for preparing the State Implementation Plan required under the federal Clean Air Act — have stated that to attain federal air quality standards the region will need to transition to broad use of zero and near zero emission energy sources in cars, trucks and other equipment (Southern California Association of Governments et al, 2011). SCAQMD partnered with Volvo Trucks to develop, build and demonstrate a prototype Class 8 heavy-duty plug-in hybrid drayage truck with significantly reduced emissions and fuel use. Volvo’s approach leveraged the group’s global knowledge and experience in designing and deploying electromobility products. The proprietary hybrid driveline selected for this proof of concept was integrated with multiple enhancements to the complete vehicle in order to maximize the emission and energy impact of electrification. A detailed review of all

ETV-DRAFT TEST REPORT OF MOBILE SOURCE EMISSIONS CONTROL DEVICES DONALDSON COMPANY,INC. SERIES 6100 DIESEL OXIDATION CATALYST MUFFLER

Science.gov (United States)

This report reflects verification testing of a catalytic muffler for diesel trucks. Produced by Donaldson Corp., it was tested on low sulfur and ultra low sulfur fuel, and shown to have reduced emissions.

Field Evaluation of Medium-Duty Plug-in Electric Delivery Trucks

Energy Technology Data Exchange (ETDEWEB)

Prohaska, Robert [National Renewable Energy Lab. (NREL), Golden, CO (United States); Simpson, Mike [National Renewable Energy Lab. (NREL), Golden, CO (United States); Ragatz, Adam [National Renewable Energy Lab. (NREL), Golden, CO (United States); Kelly, Kenneth [National Renewable Energy Lab. (NREL), Golden, CO (United States); Smith, Kandler [National Renewable Energy Lab. (NREL), Golden, CO (United States); Walkowicz, Kevin [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2016-12-01

This report focuses on medium-duty electric delivery vehicles operated by Frito-Lay North America (FLNA) at its Federal Way, Washington, distribution center. The 100% electric drive system is an alternative to conventional diesel delivery trucks and reduces both energy consumption and carbon dioxide (CO2) emissions. The vehicles' drive cycles and operation are analyzed and compared to demonstrate the importance of matching specific electric vehicle (EV) technologies to the appropriate operational duty cycle. The results of this analysis show that the Smith Newton EVs demonstrated a 68% reduction in energy consumption over the data reporting period compared to the conventional diesel vehicles, as well as a 46.4% reduction in CO₂ equivalent emissions based on the local energy generation source. In addition to characterizing the in-use performance of the EVs compared to the conventional diesels, detailed facility load data were collected at the main building power feed as well as from each of the 10 EV chargers to better understand the broader implications associated with commercial EV deployment. These facility loads were incorporated into several modeling scenarios to demonstrate the potential benefits of integrating onsite renewables.

Primary gas- and particle-phase emissions and secondary organic aerosol production from gasoline and diesel off-road engines.

Science.gov (United States)

Gordon, Timothy D; Tkacik, Daniel S; Presto, Albert A; Zhang, Mang; Jathar, Shantanu H; Nguyen, Ngoc T; Massetti, John; Truong, Tin; Cicero-Fernandez, Pablo; Maddox, Christine; Rieger, Paul; Chattopadhyay, Sulekha; Maldonado, Hector; Maricq, M Matti; Robinson, Allen L

2013-12-17

Dilution and smog chamber experiments were performed to characterize the primary emissions and secondary organic aerosol (SOA) formation from gasoline and diesel small off-road engines (SOREs). These engines are high emitters of primary gas- and particle-phase pollutants relative to their fuel consumption. Two- and 4-stroke gasoline SOREs emit much more (up to 3 orders of magnitude more) nonmethane organic gases (NMOGs), primary PM and organic carbon than newer on-road gasoline vehicles (per kg of fuel burned). The primary emissions from a diesel transportation refrigeration unit were similar to those of older, uncontrolled diesel engines used in on-road vehicles (e.g., premodel year 2007 heavy-duty diesel trucks). Two-strokes emitted the largest fractional (and absolute) amount of SOA precursors compared to diesel and 4-stroke gasoline SOREs; however, 35-80% of the NMOG emissions from the engines could not be speciated using traditional gas chromatography or high-performance liquid chromatography. After 3 h of photo-oxidation in a smog chamber, dilute emissions from both 2- and 4-stroke gasoline SOREs produced large amounts of semivolatile SOA. The effective SOA yield (defined as the ratio of SOA mass to estimated mass of reacted precursors) was 2-4% for 2- and 4-stroke SOREs, which is comparable to yields from dilute exhaust from older passenger cars and unburned gasoline. This suggests that much of the SOA production was due to unburned fuel and/or lubrication oil. The total PM contribution of different mobile source categories to the ambient PM burden was calculated by combining primary emission, SOA production and fuel consumption data. Relative to their fuel consumption, SOREs are disproportionately high total PM sources; however, the vastly greater fuel consumption of on-road vehicles renders them (on-road vehicles) the dominant mobile source of ambient PM in the Los Angeles area.

Analysis of the market for diesel PEM fuel cell auxiliary power units onboard long-haul trucks and of its implications for the large-scale adoption of PEM FCs

International Nuclear Information System (INIS)

Contestabile, Marcello

2010-01-01

Proton exchange membrane fuel cells (PEM FCs) offer a promising alternative to internal combustion engines in road transport. During the last decade PEM FC research, development and demonstration (RD and D) activities have been steadily increasing worldwide, and targets have been set to begin their commercialisation in road transport by 2015-2020. However, there still is considerable uncertainty on whether these targets will actually be met. The picture is complex and market and technology issues are closely interlinked; investment in RD and D projects is essential but not sufficient; the development of suitable early markets is also necessary and policy is set to play an important role. Auxiliary power units (APUs) are generally regarded as one important early market for FCs in transport. This paper analyses the possible future market for diesel PEM FC APUs onboard long-haul trucks and its implications for the development of PEM FCs in general. The analysis, part of the project HyTRAN (EC Contract no. 502577), is aided by the use of a dynamic simulation model of technology and markets developed by the author. Results suggest that an interesting window of opportunity for diesel PEM FC APUs exists but this is subject to additional research particularly targeted at the rapid development of fuel processors.

40 CFR Appendix Xii to Part 86 - Tables for Production Compliance Auditing of Heavy-Duty Engines and Heavy-Duty Vehicles...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 19 2010-07-01 2010-07-01 false Tables for Production Compliance Auditing of Heavy-Duty Engines and Heavy-Duty Vehicles, Including Light-Duty Trucks XII Appendix XII to... Appendix XII to Part 86—Tables for Production Compliance Auditing of Heavy-Duty Engines and Heavy-Duty...

Atmospheric behavior of urban diesel soot tagged with an iridium tracer

International Nuclear Information System (INIS)

Suarez, A.E.; Caffrey, P.F.; Borgoul, P.V.; Ondov, J.M.

1995-01-01

An important source of polynuclear aromatic hydrocarbons depositing to the Chesapeake Bay is diesel emissions, including, those from the heavily-industrial City of Baltimore which lies 3 of diesel fuel burned by the City of Baltimore's sanitation truck fleet for a 20-day period in August, 1995. Size-segregated aerosol was collected daily using 80-L min -1 dichotomous samplers at four land-bas3ed sites and aboard ship at two locations on the Chesapeake Bay. Shipboard samples were collected on the EPA's Research Vessel Anderson, either east or southeast of Baltimore, off Annapolis. Three of the land sites, i.e., those at Catonsville, MD, the Eastern Avenue Fire Station (14 km from the Bay), and the Coast Guard Station at Still pond (30 km northeast of Baltimore) were chosen to be aligned with prevailing westerly winds. The fourth site was located on Hart Miller Island, about 14 km southeast of the Fire Station to take advantage of drainage flow along the Patapsco River. In addition, 10-stage Micro-Orifice Impactors were operated daily aboard ship and at all but the Catonsville site. Deposition plates were exposed aboard ship and at two of the land sites. Finally, several samples of tagged diesel emissions were collected with an MOI mounted on one of the sanitation trucks. Iridium and ≤ 40 other elements were determined by neutron activation analysis or X-ray fluorescence; graphitic carbon by light transmission, and aerosol mass by gravimetry

Pulsed Plasma Processing of Diesel Engine Exhaust Final Report CRADA No. TC-0336-92-1-C

Energy Technology Data Exchange (ETDEWEB)

Merritt, Bernard T. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Broering, Louis [Cummins Engine Company, Inc., Columbus, IN (United States)

2017-11-09

The goal was to develop an exhaust-gas treatment process for the reduction of NO_x and hydrocarbon from diesel engines. The project began believing that direct chemical reduction on NO_x was possible through the use of non-thermal plasmas. The original CRADA began in 1993 and was scheduled to finish in 1996. It had as its goals three metrics: 1) remove two grams/brake-horse-power-hour of NOx, 2) have no more than five percent energy penalty, and 3) cost no more than ten percent of the engine cost. These goals were all aimed at heavy-duty diesel trucks. This CRADA had its Defense Program funding eliminated by DOE prior to completion in 1995. Prior to loss of funding from DOE, LLNL discovered that due to the large oxygen content in diesel exhaust, direct chemical reduction was not possible. In understanding why, a breakthrough was achieved that combined the use of a non-thermal plasma and a catalyst. This process was named Plasma Assisted Catalytic Reduction (P ACR). Because of this breakthrough, the CRADA became a funds-in only CRADA, once DOE DP funding ended. As a result, the funding decreased from about 1M dollars per year to about $400k per year. Subsequently, progress slowed as well. The CRADA was amended several times to reflect the funds-in nature. At each amendment, the deliverables were modified; the goals remained the same but the focus changed from heavy-duty to lightduty to SUVs. The diesel-engine NO_x problem is similar to the furnace and boiler NO_x emission problem with the added constraint that ammonia-like additives are impractical for a mobile source. Lean-burning gasoline engines are an additional area of application because the standard three-way catalyst is rendered ineffective by the presence of oxygen. In the P ACR process an electrical discharge is used to create a non-thermal plasma that contains oxidative radicals O and OH. These oxidative radicals convert NO to NO₂. Selective catalytic

Fuel Cell-Powered Lift Truck Fleet Deployment Projects Final Technical Report May 2014

Energy Technology Data Exchange (ETDEWEB)

Klingler, James J [GENCO Infrastructure Solutions, Inc.

2014-05-06

The overall objectives of this project were to evaluate the performance, operability and safety of fork lift trucks powered by fuel cells in large distribution centers. This was accomplished by replacing the batteries in over 350 lift trucks with fuel cells at five distribution centers operated by GENCO. The annual cost savings of lift trucks powered by fuel cell power units was between $2,400 and $5,300 per truck compared to battery powered lift trucks, excluding DOE contributions. The greatest savings were in fueling labor costs where a fuel cell powered lift truck could be fueled in a few minutes per day compared to over an hour for battery powered lift trucks which required removal and replacement of batteries. Lift truck operators where generally very satisfied with the performance of the fuel cell power units, primarily because there was no reduction in power over the duration of a shift as experienced with battery powered lift trucks. The operators also appreciated the fast and easy fueling compared to the effort and potential risk of injury associated with switching heavy batteries in and out of lift trucks. There were no safety issues with the fueling or operation of the fuel cells. Although maintenance costs for the fuel cells were higher than for batteries, these costs are expected to decrease significantly in the next generation of fuel cells, making them even more cost effective.

Comparative evaluation of three alternative power cycles for waste heat recovery from the exhaust of adiabatic diesel engines

Science.gov (United States)

Bailey, M. M.

1985-01-01

Three alternative power cycles were compared in application as an exhaust-gas heat-recovery system for use with advanced adiabatic diesel engines. The power cycle alternatives considered were steam Rankine, organic Rankine with RC-1 as the working fluid, and variations of an air Brayton cycle. The comparison was made in terms of fuel economy and economic payback potential for heavy-duty trucks operating in line-haul service. The results indicate that, in terms of engine rated specific fuel consumption, a diesel/alternative-power-cycle engine offers a significant improvement over the turbocompound diesel used as the baseline for comparison. The maximum imporvement resulted from the use of a Rankine cycle heat-recovery system in series with turbocompounding. The air Brayton cycle alternatives studied, which included both simple-cycle and compression-intercooled configurations, were less effective and provided about half the fuel consumption improvement of the Rankine cycle alternatives under the same conditions. Capital and maintenance cost estimates were also developed for each of the heat-recovery power cycle systems. These costs were integrated with the fuel savings to identify the time required for net annual savings to pay back the initial capital investment. The sensitivity of capital payback time to arbitrary increases in fuel price, not accompanied by corresponding hardware cost inflation, was also examined. The results indicate that a fuel price increase is required for the alternative power cycles to pay back capital within an acceptable time period.

NIOSH national survey of long-haul truck drivers: Injury and safety

Science.gov (United States)

Chen, Guang X.; Sieber, W. Karl; Lincoln, Jennifer E.; Birdsey, Jan; Hitchcock, Edward M.; Nakata, Akinori; Robinson, Cynthia F.; Collins, James W.; Sweeney, Marie H.

2015-01-01

Approximately 1,701,500 people were employed as heavy and tractor-trailer truck drivers in the United States in 2012. The majority of them were long-haul truck drivers (LHTDs). There are limited data on occupational injury and safety in LHTDs, which prompted a targeted national survey. The National Institute of Occupational Safety and Health conducted a nationally representative survey of 1265 LHTDs at 32 truck stops across the contiguous United States in 2010. Data were collected on truck crashes, near misses, moving violations, work-related injuries, work environment, safety climate, driver training, job satisfaction, and driving behaviors. Results suggested that an estimated 2.6% of LHTDs reported a truck crash in 2010, 35% reported at least one crash while working as an LHTD, 24% reported at least one near miss in the previous 7 days, 17% reported at least one moving violation ticket and 4.7% reported a non-crash injury involving days away from work in the previous 12 months. The majority (68%) of non-crash injuries among company drivers were not reported to employers. An estimate of 73% of LHTDs (16% often and 58% sometimes) perceived their delivery schedules unrealistically tight; 24% often continued driving despite fatigue, bad weather, or heavy traffic because they needed to deliver or pick up a load at a given time; 4.5% often drove 10 miles per hours or more over the speed limit; 6.0% never wore a seatbelt; 36% were often frustrated by other drivers on the road; 35% often had to wait for access to a loading dock; 37% reported being noncompliant with hours-of-service rules (10% often and 27% sometimes); 38% of LHTDs perceived their entry-level training inadequate; and 15% did not feel that safety of workers was a high priority with their management. This survey brings to light a number of important safety issues for further research and interventions, e.g., high prevalence of truck crashes, injury underreporting, unrealistically tight delivery schedules

Fuel Property, Emission Test, and Operability Results from a Fleet of Class 6 Vehicles Operating on Gas-to-Liquid Fuel and Catalyzed Diesel Particle Filters

Energy Technology Data Exchange (ETDEWEB)

Alleman, T. L.; Eudy, L.; Miyasato, M.; Oshinuga, A.; Allison, S.; Corcoran, T.; Chatterjee, S.; Jacobs, T.; Cherrillo, R. A.; Clark, R.; Virrels, I.; Nine, R.; Wayne, S.; Lansing, R.

2005-11-01

A fleet of six 2001 International Class 6 trucks operating in southern California was selected for an operability and emissions study using gas-to-liquid (GTL) fuel and catalyzed diesel particle filters (CDPF). Three vehicles were fueled with CARB specification diesel fuel and no emission control devices (current technology), and three vehicles were fueled with GTL fuel and retrofit with Johnson Matthey's CCRT diesel particulate filter. No engine modifications were made.

Assessing crash risk considering vehicle interactions with trucks using point detector data.

Science.gov (United States)

Hyun, Kyung Kate; Jeong, Kyungsoo; Tok, Andre; Ritchie, Stephen G

2018-03-12

Trucks have distinct driving characteristics in general traffic streams such as lower speeds and limitations in acceleration and deceleration. As a consequence, vehicles keep longer headways or frequently change lane when they follow a truck, which is expected to increase crash risk. This study introduces several traffic measures at the individual vehicle level to capture vehicle interactions between trucks and non-trucks and analyzed how the measures affect crash risk under different traffic conditions. The traffic measures were developed using headways obtained from Inductive Loop Detectors (ILDs). In addition, a truck detection algorithm using a Gaussian Mixture (GM) model was developed to identify trucks and to estimate truck exposure from ILD data. Using the identified vehicle types from the GM model, vehicle interaction metrics were categorized into three groups based on the combination of leading and following vehicle types. The effects of the proposed traffic measures on crash risk were modeled in two different cases of prior- and non-crash using a case-control approach utilizing a conditional logistic regression. Results showed that the vehicle interactions between the leading and following vehicle types were highly associated with crash risk, and further showed different impacts on crash risk by traffic conditions. Specifically, crashes were more likely to occur when a truck following a non-truck had shorter average headway but greater headway variance in heavy traffic while a non-truck following a truck had greater headway variance in light traffic. This study obtained meaningful conclusions that vehicle interactions involved with trucks were significantly related to the crash likelihood rather than the measures that estimate average traffic condition such as total volume or average headway of the traffic stream. Copyright © 2018 Elsevier Ltd. All rights reserved.

Bioremediation of heavy metals and petroleum hydrocarbons in diesel contaminated soil with the earthworm: Eudrilus eugeniae.

Science.gov (United States)

Ekperusi, Ogheneruemu Abraham; Aigbodion, Iruobe Felix

2015-01-01

A laboratory study on the bioremediation of diesel contaminated soil with the earthworm Eudrilus eugeniae (Kingberg) was conducted. 5 ml of diesel was contaminated into soils in replicates and inoculated with E. eugeniae for 90 days. Physicochemical parameters, heavy metals and total petroleum hydrocarbons were analyzed using AAS. BTEX in contaminated soil and tissues of earthworms were determined with GC-FID. The activities of earthworms resulted in a decrease in pH (3.0 %), electrical conductivity (60.66 %), total nitrogen (47.37 %), chloride (60.66 %), total organic carbon (49.22 %), sulphate (60.59 %), nitrate (60.65 %), phosphate (60.80 %), sodium (60.65 %), potassium (60.67 %), calcium (60.67 %), magnesium (60.68 %), zinc (60.59 %), manganese (60.72 %), copper (60.68 %), nickel (60.58 %), cadmium (60.44 %), vanadium (61.19 %), chromium (53.60 %), lead (60.38 %), mercury (61.11 %), arsenic (80.85 %), TPH (84.99 %). Among the BTEX constituents, only benzene (8.35 %) was detected in soil at the end of the study. Earthworm tissue analysis showed varying levels of TPH (57.35 %), benzene (38.91 %), toluene (27.76 %), ethylbenzene (42.16 %) and xylene (09.62 %) in E. eugeniae at the end of the study. The study has shown that E. eugeniae could be applied as a possible bioremediator in diesel polluted soil.

One step processing for future diesel specifications

International Nuclear Information System (INIS)

Brierley, G.R.

1997-01-01

The trend in diesel fuel specifications is to limit the sulfur level to less than 0.05 wt- per cent. Many regions have also specified that diesel fuels must have lower aromatic levels, higher cetane numbers, and lower distillation end points. These changes will require significant refinery investment to meet the new diesel fuel specifications. The changes may also significantly affect the value of synthetic crude stocks. UOP has developed a new hydroprocessing catalyst which makes it possible to meet the new diesel specifications in one single processing step and at minimal cost. The catalyst saturates aromatics while opening ring structures at the same time. By selectively cracking heavy components into the diesel range with minimal cracking to gas or naphtha, heavier feedstocks can be upgraded to diesel, and refinery diesel yield can be augmented. Synthetic crude distillate is often high in aromatics and low in cetane number. This new UOP hydroprocessing system will allow synthetic crude producers and refiners to produce diesel fuels with higher cetane numbers, high-quality distillate blendstocks and distillate fuels. 26 figs

Carbonaceous composition changes of heavy-duty diesel engine particles in relation to biodiesels, aftertreatments and engine loads.

Science.gov (United States)

Cheng, Man-Ting; Chen, Hsun-Jung; Young, Li-Hao; Yang, Hsi-Hsien; Tsai, Ying I; Wang, Lin-Chi; Lu, Jau-Huai; Chen, Chung-Bang

2015-10-30

Three biodiesels and two aftertreatments were tested on a heavy-duty diesel engine under the US FTP transient cycle and additional four steady engine loads. The objective was to examine their effects on the gaseous and particulate emissions, with emphasis given to the organic and elemental carbon (OC and EC) in the total particulate matter. Negligible differences were observed between the low-sulfur (B1S50) and ultralow-sulfur (B1S10) biodiesels, whereas small reductions of OC were identified with the 10% biodiesel blend (B10). The use of diesel oxidation catalyst (DOC1) showed moderate reductions of EC and particularly OC, resulting in the OC/EC ratio well below unity. The use of DOC plus diesel particulate filter (DOC2+DPF) yielded substantial reductions of OC and particularly EC, resulting in the OC/EC ratio well above unity. The OC/EC ratios were substantially above unity at idle and low load, whereas below unity at medium and high load. The above changes in particulate OC and EC are discussed with respect to the fuel content, pollutant removal mechanisms and engine combustion conditions. Overall, the present study shows that the carbonaceous composition of PM could change drastically with engine load and aftertreatments, and to a lesser extent with the biodiesels under study. Copyright © 2015 Elsevier B.V. All rights reserved.

Bias of averages in life-cycle footprinting of infrastructure: truck and bus case studies.

Science.gov (United States)

Taptich, Michael N; Horvath, Arpad

2014-11-18

The life-cycle output (e.g., level of service) of infrastructure systems heavily influences their normalized environmental footprint. Many studies and tools calculate emission factors based on average productivity; however, the performance of these systems varies over time and space. We evaluate the appropriate use of emission factors based on average levels of service by comparing them to those reflecting a distribution of system outputs. For the provision of truck and bus services where fuel economy is assumed constant over levels of service, emission factor estimation biases, described by Jensen's inequality, always result in larger-than-expected environmental impacts (3%-400%) and depend strongly on the variability and skew of truck payloads and bus ridership. Well-to-wheel greenhouse gas emission factors for diesel trucks in California range from 87 to 1,500 g of CO2 equivalents per ton-km, depending on the size and type of trucks and the services performed. Along a bus route in San Francisco, well-to-wheel emission factors ranged between 53 and 940 g of CO2 equivalents per passenger-km. The use of biased emission factors can have profound effects on various policy decisions. If average emission rates must be used, reflecting a distribution of productivity can reduce emission factor biases.

Dual-fuelling of a direct-injection automotive diesel engine by diesel and compressed natural gas

International Nuclear Information System (INIS)

Pirouzpanah, V.; Mohammadi Kosha, A.; Mosseibi, A.; Moshirabadi, J.; Gangi, A.; Moghadaspour, M.

2000-01-01

Application of Compressed Natural Gas in diesel engines has always been important, especially in the field of automotive engineering. This is due to easy accessibility, better mixing quality and good combustion characteristics of the Compressed Natural Gas fuel. In this study the application of Compressed Natural Gas fuel along with diesel oil in a heavy duty direct-injection automotive diesel engine is experimentally investigated. In order to convert a diesel engine into a diesel-gas one, the so called m ixed diesel-gas a pproach has been used and for this purpose a carbureted Compressed Natural Gas fuel system has been designed and manufactured. For controlling quantity of Compressed Natural Gas, the gas valve is linked to the diesel fuel injection system by means of a set of rods. Then, the dual-fuel system is adjusted so that, at full load conditions, the quantity of diesel fuel is reduced to 20% and 80% of its equivalent energy is substituted by Compressed Natural Gas fuel. Also injection pressure of pilot jet is increased by 11.4%. Performance and emission tests are conducted under variation of load and speed on both diesel and diesel-gas engines. Results show that, with equal power and torque, the diesel-gas engine has the potential to improve overall engine performance and emission. For example, at rated power and speed, fuel economy increases by 5.48%, the amount of smoke decreases by 78%, amount of CO decreases by 64.3% and mean exhaust gas temperature decreases by 6.4%

Haulage Truck Operator. Open Pit Mining Job Training Series.

Science.gov (United States)

British Columbia Dept. of Education, Victoria.

This training outline for haulage truck operators, one in a series of eight outlines, is designed primarily for company training foremen or supervisors and for trainers to use as an industry-wide guideline for heavy equipment operator training in open pit mining in British Columbia. Intended as a guide for preparation of lesson plans both for…

Development of A Hydraulic Drive for a novel Diesel-Hydraulic system for Large commercial Vehicles

DEFF Research Database (Denmark)

Stecki, J. S.; Conrad, Finn; Matheson, P.

2002-01-01

The objectives and results of the research project Hybrid Diesel-Hydraulic System for Large commercial vehicles, e.g. urban freight delivery, buses or garbage trucks. The paper presents and discusses the research and development of the system, modelling approach and results from preliminary...... performance tests on a 10 ton vehicle....

Exhaust particle and NOx emission performance of an SCR heavy duty truck operating in real-world conditions

Science.gov (United States)

Saari, Sampo; Karjalainen, Panu; Ntziachristos, Leonidas; Pirjola, Liisa; Matilainen, Pekka; Keskinen, Jorma; Rönkkö, Topi

2016-02-01

Particle and NOx emissions of an SCR equipped HDD truck were studied in real-world driving conditions using the "Sniffer" mobile laboratory. Real-time CO2 measurement enables emission factor calculation for NOx and particles. In this study, we compared three different emission factor calculation methods and characterised their suitability for real-world chasing experiments. The particle number emission was bimodal and dominated by the nucleation mode particles (diameter below 23 nm) having emission factor up to 1 × 1015 #/kgfuel whereas emission factor for soot (diameter above 23 nm that is consistent with the PMP standard) was typically 1 × 1014 #/kgfuel. The effect of thermodenuder on the exhaust particles indicated that the nucleation particles consisted mainly of volatile compounds, but sometimes there also existed a non-volatile core. The nucleation mode particles are not controlled by current regulations in Europe. However, these particles consistently form under atmospheric dilution in the plume of the truck and constitute a health risk for the human population that is exposed to those. Average NOx emission was 3.55 g/kWh during the test, whereas the Euro IV emission limit over transient testing is 3.5 g NOx/kWh. The on-road emission performance of the vehicle was very close to the expected levels, confirming the successful operation of the SCR system of the tested vehicle. Heavy driving conditions such as uphill driving increased both the NOx and particle number emission factors whereas the emission factor for soot particle number remains rather constant.

Lift truck safety review

Energy Technology Data Exchange (ETDEWEB)

Cadwallader, L.C.

1997-03-01

This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter`s Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given.

Lift truck safety review

International Nuclear Information System (INIS)

Cadwallader, L.C.

1997-03-01

This report presents safety information about powered industrial trucks. The basic lift truck, the counterbalanced sit down rider truck, is the primary focus of the report. Lift truck engineering is briefly described, then a hazard analysis is performed on the lift truck. Case histories and accident statistics are also given. Rules and regulations about lift trucks, such as the US Occupational Safety an Health Administration laws and the Underwriter's Laboratories standards, are discussed. Safety issues with lift trucks are reviewed, and lift truck safety and reliability are discussed. Some quantitative reliability values are given

LPG as a Fuel for Diesel Engines-Experimental Investigations

Science.gov (United States)

Cristian Nutu, Nikolaos; Pana, Constantin; Negurescu, Niculae; Cernat, Alexandru; Mirica, Ionel

2017-10-01

The main objective of the paper is to reduce the pollutant emissions of a compression ignition engine, fuelling the engine with liquefied petroleum gas (LPG), aiming to maintain the energetic performances of the engine. To optimise the engine operation a corelation between the substitute ratio of the diesel fuel with LPG and the adjustments for the investigated regimens must be made in order to limit the maximum pressure and smoke level, knock and rough engine functioning, fuel consumption and the level of the pollutant emissions. The test bed situated in the Thermotechnics, Engines, Thermal Equipments and Refrigeration Instalations Department was adapted to be fuelled with liquefied petroleum gas. A conventional LPG fuelling instalation was adopted, consisting of a LPG tank, a vaporiser, conections between the tank and the vaporiser and a valve to adjust the gaseous fuel flow. Using the diesel-gas methode, in the intake manifold of the engine is injected LPG in gaseous aggregation state and the airr-LPG homogeneous mixture is ignited from the flame appeared in the diesel fuel sprays. To maintain the engine power at the same level like in the standard case of fuelling only with diesel fuel, for each investigated operate regimen the diesel fuel dose was reduced, being energetically substituted with LPG. The engine used for experimental investigations is a turbocharged truck diesel engine with a 10.34 dm3 displacement. The investigated working regimen was 40% load and 1750 rpm and the energetic substitute ratios of the diesel fuel with LPG was situated between [0-25%].

Diesel Emission Control -- Sulfur Effects (DECSE) Program; Phase I Interim Data Report No. 1

Energy Technology Data Exchange (ETDEWEB)

DOE; ORNL; NREL; EMA; MECA

1999-08-15

The Diesel Emission Control-Sulfur Effects (DECSE) is a joint government/industry program to determine the impact of diesel fuel sulfur levels on emission control systems whose use could lower emissions of nitrogen oxides (NO{sub x}) and particulate matter (PM) from on-highway trucks in the 2002--2004 model years. Phase 1 of the program was developed with the following objectives in mind: (1) evaluate the effects of varying the level of sulfur content in the fuel on the emission reduction performance of four emission control technologies; and (2) measure and compare the effects of up to 250 hours of aging on selected devices for multiple levels of fuel sulfur content. This interim data report summarizes results as of August, 1999, on the status of the test programs being conducted on three technologies: lean-NO{sub x} catalysts, diesel particulate filters and diesel oxidation catalysts.

Integrated online energy and battery life management for hybrid long haulage truck

NARCIS (Netherlands)

Pham, H.T.; Kessels, J.T.B.A.; Bosch, van den P.P.J.; Huisman, R.G.M.

2014-01-01

Battery lifetime management plays an important role for successful commercializing hybrid electric vehicles. This paper aims at integrating the battery lifetime management into the energy management system of a heavy-duty hybrid electric truck. The developed strategy called Integrated Energy

PERFORMANCE AND EMISSIONS OF A HEAVY DUTY DIESEL ENGINE FUELLED WITH PALM OIL BIODIESEL AND PREMIUM DIESEL

Directory of Open Access Journals (Sweden)

HELMER ACEVEDO

2011-01-01

Full Text Available Biodiesel es promocionado como combustible alternativo para sustituir combustibles de origen fósil y reducir emisiones de carbono. Algunos estudios han sido llevados a cabo para estudiar las emisiones de vehículos diesel de baja potencia. Sin embargo, las emisiones sólidas y gaseosas emitidas por vehículos de trabajo operados con biodiesel de palma africana y diesel de bajo contenido de azufre (~ 15 ppm han sido poco estudiadas. El objetivo de este estudio fue determinar el desempeño y emisiones de un motor Diesel Cummins, 4 tiempos, 9.5 litros, 6 cilindros con sistema de inyección "common rail", y sistema de recirculación de gases. El motor desarrolló una menor potencia (10 % cuando fue operado con biodiesel de palma africana. El motor cumplió con la norma ambiental 2004 cuando fue operado con combustible diesel, sin embargo, con biodiesel de palma africana las emisiones de material particulado y los óxidos de nitrógeno estuvieron fuera de norma.

Evaluation of approaches for improving diesel cold flow properties

Energy Technology Data Exchange (ETDEWEB)

Sharafutdinov, Ilshat; Stratiev, Dicho; Dinkov, Rossen [Lukoil Neftochim Bourgas AD, Bourgas (Bulgaria); Bachvarov, Assen [Edinburgh Univ. (United Kingdom); Petkov, Petko [Bourgas Univ. ' ' Assen Zlatarov' ' (Bulgaria)

2012-06-15

Four heavy diesel fractions (FBP according to ASTM D-2887 of about 420 C), one lower boilingmiddle distillate fraction (FBP according to ASTM D-2887 of 310 C) and kerosene fraction (FBP according to ASTM D-2887 of 271 C) obtained from the Lukoil Neftochim Burgas (LNB) process units during the processing of Russian Export Crude Blend (REBCO) along with four heavy diesel fractions (FBP according to ASTM D-2887 of about 370 C) obtained by fractionation of four crudes: Oil Blend, REBCO, Siberian Light Crude Oil (SLCO) and CPC (Caspian Consortium Pipeline) were investigated for their cold flow properties. It was found that undercutting diesel improves cloud point (CP) and cold filter plugging point (CFPP) by 4 C/10 C cut point. Blending of kerosene improves CP and CFPP by about 2 C/10% added kerosene. The treatment with CP depressants may improve CP by about 2 C if the proper combination diesel - depressant is selected and the improvement can reach up to 6 C for a definite diesel. The treatment with CFPP depressant is much more efficient achieving an improvement of 18 C. By assuming definite fuel prices (Platts) and by applying the LNB linear programming model using Honeywell's RPMS software it was found that catalytic dewaxing is the most efficient approach for producing diesel with improved cold flowproperties if the diesel yield from the dewaxing process is higher than 90%. (orig.)

Diesel Engine Waste Heat Recovery Utilizing Electric Turbocompound Technology

International Nuclear Information System (INIS)

Gerke, Frank G.

2001-01-01

This cooperative program between the DOE Office of Heavy Vehicle Technology and Caterpillar, Inc. is aimed at demonstrating electric turbocompound technology on a Class 8 truck engine. This is a lab demonstration program, with no provision for on-truck testing of the system. The goal is to demonstrate the level of fuel efficiency improvement attainable with the electric turbocompound system. Also, electric turbocompounding adds an additional level of control to the air supply which could be a component in an emissions control strategy

AUTOMOTIVE DIESEL MAINTENANCE 1. UNIT XXV, I--CATERPILLAR DIESEL ENGINE COOLING SYSTEM D-8 AND 824 MODELS, II--TIRES AND TIRE HARDWARE.

Science.gov (United States)

Minnesota State Dept. of Education, St. Paul. Div. of Vocational and Technical Education.

THIS MODULE OF A 30-MODULE COURSE IS DESIGNED TO DEVELOP AN UNDERSTANDING OF THE OPERATION AND MAINTENANCE OF THE DIESEL ENGINE COOLING SYSTEM AND TO PROVIDE A DESCRIPTION OF HEAVY TIRES AND WHEELS USED ON DIESEL POWERED VEHICLES. TOPICS ARE (1) THEORY OF THE COOLING SYSTEM, (2) COOLING SYSTEM COMPONENTS, (3) MAINTENANCE TIPS (COOLING SYSTEM), (4)…

4th international exhaust gas and particulate emissions forum. Proceedings; 4. internationales FORUM Abgas- und Partikelemissionen. Beitraege

Energy Technology Data Exchange (ETDEWEB)

NONE

2006-07-01

Lectures of the conference addressed the following topics: European and US American pollution regulations, particulate measuring systems, emission factors for vehicles, particulate emission abatement through simulation and optimization, selective catalytic reduction in heavy duty diesel trucks, filters, combustion properties, performance assessment, contribution of biofuels. (uke)

Shock and vibration environments for large shipping containers on rail cars and trucks

International Nuclear Information System (INIS)

Magnuson, C.F.; Wilson, L.T.

1977-06-01

The purpose of this study was to provide definitions of shock and vibration environment to which fissile material shipping containers may be exposed during normal shipment by truck and rail cars. The definitions of vibration, shock superimposed on vibration and rail coupling shock result from existing data. The dependence of shock environment, from rail coupling operations, on parameters like cargo weight and shock attenuation couplers was also studied using spring-mass models. These studies show that for rail cars equipped with standard draft gear, the cargo response decreases with increased cargo weight until the springs bottom out. For rail cars equipped with shock attenuation couplers, cargo weight has little effect on cargo response. The study also shows the importance of matching couplers and tiedown stiffnesses to decrease the cargo response. Vibration and shock data samples have been obtained during truck shipment of heavy cargo and the data will be presented in subsequent reports. Similar data need to be obtained for rail shipment of heavy cargo and during rail coupling operations with heavy cargo

Cummins L10G in Kenworth truck 'viable today'

International Nuclear Information System (INIS)

Anon.

1996-01-01

As the culmination of five years of developmental work by Cummins Engines, BC Research Inc., and BC Gas Utility Ltd., a T800 Kenworth truck was outfitted with a new Cummins L10G natural gas engine, and two lightweight fully -wrapped Dynetek cylinders; it was pronounced to be 'a viable clean truck today'. The L10G spark-ignited engine operates at a relatively high peak efficiency of 37 per cent and is commercially available to meet the current California Air Resources Board heavy duty vehicle emission standards without the use of a catalytic converter. The L10G engine produces no particulate emissions, a very significant advantage, in view of the fact that particulate emissions have been identified as major contributors to respiratory ailments

Truck acceleration behavior study and acceleration lane length recommendations for metered on-ramps

Directory of Open Access Journals (Sweden)

Guangchuan Yang

2016-10-01

Full Text Available This paper investigated the actual truck acceleration capability at metered on-ramps. Truck acceleration performance data were collected through a video-based data collection method. A piecewise constant acceleration model was employed to capture truck acceleration characteristics. It was found that the existing acceleration length will affect truck drivers’ acceleration behavior. At the taper type ramp that has limited acceleration distance, acceleration profile indicated a decreasing trend with distance. While for the ramp with an auxiliary lane that has sufficient acceleration distance, it was found that the acceleration behavior is to have a high acceleration rate in the beginning, then acceleration rate decrease with speed increase, and high acceleration rate again as drivers approach the merging area. Field data show that the truck acceleration performance data documented in the ITE’s (Institute of Transportation Engineers “Traffic Engineering Handbook” are much lower than the field collected data. Also, based on the regression analysis of speed versus distance profiles, it was found that the AASHTO’s (American Association of State Highway and Transportation Officials Green Book acceleration length design guidance is insufficient to accommodate trucks at metered on-ramps. The required acceleration lengths for medium and heavy trucks are approximately 1.3 and 1.6 times of the Green Book design guideline, respectively.

Total Particle Number Emissions from Modern Diesel, Natural Gas, and Hybrid Heavy-Duty Vehicles During On-Road Operation.

Science.gov (United States)

Wang, Tianyang; Quiros, David C; Thiruvengadam, Arvind; Pradhan, Saroj; Hu, Shaohua; Huai, Tao; Lee, Eon S; Zhu, Yifang

2017-06-20

Particle emissions from heavy-duty vehicles (HDVs) have significant environmental and public health impacts. This study measured total particle number emission factors (PNEFs) from six newly certified HDVs powered by diesel and compressed natural gas totaling over 6800 miles of on-road operation in California. Distance-, fuel- and work-based PNEFs were calculated for each vehicle. Distance-based PNEFs of vehicles equipped with original equipment manufacturer (OEM) diesel particulate filters (DPFs) in this study have decreased by 355-3200 times compared to a previous retrofit DPF dynamometer study. Fuel-based PNEFs were consistent with previous studies measuring plume exhaust in the ambient air. Meanwhile, on-road PNEF shows route and technology dependence. For vehicles with OEM DPFs and Selective Catalytic Reduction Systems, PNEFs under highway driving (i.e., 3.34 × 10 12 to 2.29 × 10 13 particles/mile) were larger than those measured on urban and drayage routes (i.e., 5.06 × 10 11 to 1.31 × 10 13 particles/mile). This is likely because a significant amount of nucleation mode volatile particles were formed when the DPF outlet temperature reached a critical value, usually over 310 °C, which was commonly achieved when vehicle speed sustained over 45 mph. A model year 2013 diesel HDV produced approximately 10 times higher PNEFs during DPF active regeneration events than nonactive regeneration.

Transient performance and emission characteristics of a heavy-duty diesel engine fuelled with microalga Chlorella variabilis and Jatropha curcas biodiesels

International Nuclear Information System (INIS)

Singh, Devendra; Singal, S.K.; Garg, M.O.; Maiti, Pratyush; Mishra, Sandhya; Ghosh, Pushpito K.

2015-01-01

Highlights: • B100 biodiesels from Jatropha (BJ) and marine microalga (BA) compared. • 17% lower NOx and 6% lower specific fuel consumption of BA over BJ. • Brake specific fuel consumption (BSFC) highest in urban mode in all cases. • NOx, HC and CO highest in rural-, motorway-and urban modes, respectively. • Microalga Chlorella variabilis is a promising feedstock for renewable fuels. - Abstract: Biodiesel is a renewable alternative to petro-diesel used in compression ignition (CI) engine. Two B100 biodiesel samples were prepared by patented routes from the lipids extracted from marine microalga Chlorella variabilis (BA) cultivated in salt pans and wasteland-compatible Jatropha curcas (BJ). The fuels complied with ASTM D-6751 and European Standard EN-14214 specifications. Standard Petro-diesel served as a control. Transient performance and emission characteristics of a heavy duty diesel engine fuelled with these B100 fuels (BJ and BA) were studied over European Transient Cycle. Test results showed that both B100 biodiesels outperformed petro-diesel in terms of particulate matter (PM), carbon monoxide (CO) and hydrocarbon (HC) emissions, with slight penalty on NOx emissions. Among the two biodiesels, merits of BA were established over BJ in terms of nitrogen oxides (NOx) emissions and specific fuel consumption. Mode-wise transient emission analysis revealed that NOx was highest in rural mode, CO was highest in urban and HC was highest in motorway mode for all fuels. BA may be considered as a promising alternative fuel for diesel engine which can be produced sustainably through cultivation of the marine microalga in coastal locations using seawater as culture medium, obviating thereby concerns around land use competition for food and fuel.

Combustion and emission characteristics of diesel engine fueled with diesel-like fuel from waste lubrication oil

International Nuclear Information System (INIS)

Wang, Xiangli; Ni, Peiyong

2017-01-01

Highlights: • 100% diesel-like fuel from waste lubricating oil was conducted in a diesel engine. • Good combustion and fuel economy are achieved without engine modifications. • Combustion duration of DLF is shorter than diesel. • NOx and smoke emissions with the DLF are slightly higher than pure diesel. - Abstract: Waste lubricant oil (WLO) is one of the most important types of the energy sources. WLO cannot be burned directly in diesel engines, but can be processed to be used as diesel-like fuel (DLF) to minimize its harmful effect and maximize its useful values. Moreover, there are some differences in physicochemical properties between WLO and diesel fuel. In order to identify the differences in combustion and emission performance of diesel engine fueled with the two fuels, a bench test of a single-cylinder direct injection diesel engine without any engine modification was investigated at four engine speeds and five engine loads. The effects of the fuels on fuel economic performance, combustion characteristics, and emissions of hydrocarbons (HC), carbon monoxide (CO), nitrogen oxides (NOx) and smoke were discussed. The DLF exhibits longer ignition delay period and shorter combustion duration than diesel fuel. The test results indicate that the higher distillation temperatures of the DLF attribute to the increase of combustion pressure, temperature and heat release rate. The brake specific fuel consumption (BSFC) of the DLF compared to diesel is reduced by about 3% at 3000 rpm under light and medium loads. The DLF produces slightly higher NOx emissions at middle and heavy loads, somewhat more smoke emissions at middle loads, and notably higher HC and CO emissions at most measured points than diesel fuel. It is concluded that the DLF can be used as potential available fuel in high-speed diesel engines without any problems.

Clean Coal Diesel Demonstration Project

Energy Technology Data Exchange (ETDEWEB)

Robert Wilson

2006-10-31

A Clean Coal Diesel project was undertaken to demonstrate a new Clean Coal Technology that offers technical, economic and environmental advantages over conventional power generating methods. This innovative technology (developed to the prototype stage in an earlier DOE project completed in 1992) enables utilization of pre-processed clean coal fuel in large-bore, medium-speed, diesel engines. The diesel engines are conventional modern engines in many respects, except they are specially fitted with hardened parts to be compatible with the traces of abrasive ash in the coal-slurry fuel. Industrial and Municipal power generating applications in the 10 to 100 megawatt size range are the target applications. There are hundreds of such reciprocating engine power-plants operating throughout the world today on natural gas and/or heavy fuel oil.

Volatile organic compounds emissions from gasoline and diesel powered vehicle

Energy Technology Data Exchange (ETDEWEB)

Mugica, V [Universidad Autonoma Metropolitana, Mexico, D.F. (Mexico); Vega, E; Sanchez, G; Reyes, E; Arriaga, J. L [Instituto Mexicano del Petroleo, Mexico, D.F. (Mexico); Chow, J; Watson, J; Egami, R [Desert Research Institute, Reno, NV (United States)

2001-01-01

In this research, volatile organic compound emissions were characterized from gasoline and diesel vehicles. Sampling campaigns in the Metropolitan Area of Mexico City were designed and carried out in tunnels, crossroads, and truck and bus terminals. The samples were analyzed with gas chromatography getting more than 250 different compounds, being more or less 60 of them the 80% of all the emissions. The most abundant are the two carbon compounds, as a result of the combustion, and compounds related to fuels compositions, like isopentane, xylenes, toluene among others. The profiles obtained in tunnels and crossroads were very similar with the exception of the 3 and 4 carbon compounds, which were found in bigger proportion in the profiles at crossroads. This may probably be due to the blend with the ambient air. The profiles corresponding to trucks and buses have a smaller content of two carbon compounds and a bigger content of xylenes, toluene and ethylbenzene. The variations in the proportions of the compounds allow differentiating the profiles of vehicles using gasoline and diesel. [Spanish] En este trabajo se caracterizaron las emisiones de compuestos organicos volatiles provenientes de vehiculos a gasolina y a diesel. Para ello, se disenaron diversas campanas de muestreo en la zona Metropolitana de la Ciudad de Mexico, en tuneles, cruceros y estaciones de camiones de carga y autobuses. Las muestras se analizaron con cromatografia, de gases obteniendose mas de 250 compuestos distintos, de los cuales aproximadamente 60 corresponden a mas del 80% de las emisiones. Los compuestos mas abundantes son los de dos carbonos, resultado de la combustion, y 4 carbonos que se encontraron en mayor proporcion en los perfiles de cruceros, lo cual se debe probablemente a la mezcla con el aire ambiente. Los perfiles correspondientes a camiones de carga y autobuses tienen un menor contenido de compuestos de dos carbonos y un mayor contenido de xilenos, tolueno y etilbenceno. Estas

An experimental investigation of H{sub 2} emissions of a 2004 heavy-duty diesel engine supplemented with H{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Gatts, T.; Li, H.; Liew, C.; Liu, S.; Spencer, T.; Wayne, S.; Clark, N. [Department of Mechanical and Aerospace Engineering, West Virginia University, P.O. Box 6106, Morgantown, WV 26506 (United States)

2010-10-15

Hydrogen (H{sub 2}) emissions characteristics of H{sub 2}-diesel dual fuel engine were measured using a 2004 turbocharged heavy-duty diesel engine with H{sub 2} supplemented into the intake air. The emissions of H{sub 2} were measured using an Electron Pulse Ionization (EPI) Mass Spectrometer (MS). The effect of the amount of H{sub 2} added, the engine load, and diesel fuel flow rates on the emissions of H{sub 2} and its combustion efficiency in the engine were investigated. The addition of H{sub 2} under high load operation was notable for its ability to obtain high H{sub 2} combustion efficiency and improve brake thermal efficiency. However, the addition of H{sub 2} at low load resulted in high emissions of H{sub 2} due to the failure to initiate and support a sufficiently vigorous flame for the complete combustion of H{sub 2} present outside the diesel spray plume. The maximum H{sub 2} emissions of 1.4% (volume in dry exhaust gas) were observed with the addition of 6% H{sub 2} at 10% load. In comparison, the maximum H{sub 2} emissions of 0.13% were observed when operated at 70% load with the addition of 6% H{sub 2}. The slip of a large percentage of H{sub 2} at low load operation was shown to deteriorate the potential of H{sub 2} in improving the brake thermal efficiency. (author)

Evaluation of the Use of Ultra Low Sulfur Diesel Oil for an Emergency Diesel Generator

International Nuclear Information System (INIS)

Yun, Young-Chul; Chung, Woo-Geun

2016-01-01

The aim of this study is to assess the compatibility and effect on driving an emergency diesel generator using ULSD examining the specific gravity and lubricity of the oil. Because generators at NPPs use ULSD which is not mostly used for medium-large diesel generator engines, this study seeks to provide effective precautions for the driving stability of emergency diesel generators. One of the major fuel oils used in medium-large diesel engines for the normal driving of vessels and the generation of emergency power at power plants is heavy fuel oil. There are no vessels and power generation engines known to use high-quality diesel oil which is widely used in cars. The findings of this study suggest that when driving a diesel generator, there will be increased fuel consumption by 3.6% [m 3 /hr.]. Furthermore, the mechanical fuel limiter on the engine needs an upward adjustment because the system is set for 110% load operations for the former LSD fuel. Both LSD and ULSD retain lubricity with a WSD around 330~350μm. These results clearly show that bad lubricity problems are not expected to occur. We had presumed an increased amount of foreign particulates because of the increased additives for high lubricity and oxidative stability

Evaluation of the Use of Ultra Low Sulfur Diesel Oil for an Emergency Diesel Generator

Energy Technology Data Exchange (ETDEWEB)

Yun, Young-Chul; Chung, Woo-Geun [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

The aim of this study is to assess the compatibility and effect on driving an emergency diesel generator using ULSD examining the specific gravity and lubricity of the oil. Because generators at NPPs use ULSD which is not mostly used for medium-large diesel generator engines, this study seeks to provide effective precautions for the driving stability of emergency diesel generators. One of the major fuel oils used in medium-large diesel engines for the normal driving of vessels and the generation of emergency power at power plants is heavy fuel oil. There are no vessels and power generation engines known to use high-quality diesel oil which is widely used in cars. The findings of this study suggest that when driving a diesel generator, there will be increased fuel consumption by 3.6% [m{sup 3}/hr.]. Furthermore, the mechanical fuel limiter on the engine needs an upward adjustment because the system is set for 110% load operations for the former LSD fuel. Both LSD and ULSD retain lubricity with a WSD around 330~350μm. These results clearly show that bad lubricity problems are not expected to occur. We had presumed an increased amount of foreign particulates because of the increased additives for high lubricity and oxidative stability.

Technology updates from the OEMs (tires, rims, automation inflation systems, and alternative fuels for heavy vehicles)

Energy Technology Data Exchange (ETDEWEB)

White, N. [Charonic Canada Inc., Ottawa, ON (Canada)

2001-07-01

This power point presentation outlined a project at Charonic Canada Inc., which demonstrated and evaluated innovations in the areas of vehicle safety, operating economy and diesel fuel substitution. It also presented a range of results that demonstrate some of the trends that may be used on vehicles, particularly trucks, in the near future. The demonstration involved a 2 year observation of a five truck fleet hauling refuse from Toronto to Michigan. The trucks completed 2,500 round trips of 540 miles and used 115 tonnes of natural gas fuel replacing diesel fuel. Safety innovations included tire pressure monitoring, hazard locator radar system, anti-spray system, wheel nut and bearing temperature indicators and brake safe indicators. These features were reported as being worthwhile investments. Economy innovations included a dual-fuel engine system, wide base tires, light weight CNG tanks, centrifugal oil cleaner and an oil and lubrication system. Although the technology continues to improve, the dual-engine system requires further work. Difficulties were encountered when trying to meet performance, fuel economy and emission targets at the same time. 18 figs.

Formation and emission of organic pollutants from diesel engines

International Nuclear Information System (INIS)

Bertoli, C.; Ciajolo, A.; D'Anna, A.; Barbella, R.

1993-01-01

The emission of soot and polycyclic aromatic hydrocarbons (PAH) from diesel engines results from the competition between oxidative and pyrolytic routes which the fuel takes in the unsteady, heterogeneous conditions of the diesel combustion process. In-cylinder sampling and analysis of particulate (soot and condensed hydrocarbon species), light hydrocarbons and gaseous inorganic species were carried out in two locations of a single cylinder direct injection diesel engine by means of a fast sampling valve in order to follow the behaviour of a diesel fuel during the engine cycle. The effect of fuel quality (volatility, aromatic content, cetane number) and air/fuel mass feed ratio on soot, PAH, and light and heavy hydrocarbons was also investigated by direct sampling and chemical analysis of the exhausts emitted from a direct injection diesel engine (D.I.) and an indirect injection diesel engine (I.D.I.)

Electric refuse collection vehicle with a range extender; Elektrisches Abfallsammelfahrzeug mit Range Extender

Energy Technology Data Exchange (ETDEWEB)

Fuchs, Andreas

2012-10-15

At the Frankfurt Motor Show IAA 2012, MAN will be presenting the Metropolis, a heavy-duty truck for use in urban areas that produces no emissions and is ultra-quiet. Using mains electricity generated from renewable sources, it can operate without producing any CO{sub 2}. The truck's modular lithium-ion battery is located under the ab. A quiet and efficient diesel engine from the Volkswagen Group generates power as needed and functions as a range extender for the truck. At the end of 2012, the MAN Metropolis will start a two-year field test as a refuse collection vehicle. (orig.)

Truck shovel users group

Energy Technology Data Exchange (ETDEWEB)

Thomas, J. [Surface Mining Association for Research and Technology, AB (Canada)

2008-07-01

The Truck Shovel Users Group (TSUG) was developed as part of the Surface Mining Association for Research and Technology (SMART), an association of companies that meet to coordinate technology developments for the mining industry. The TSUG meet regularly to discuss equipment upgrades, maintenance planning systems, and repair techniques. The group strives to maximize the value of its assets through increased safety, equipment performance and productivity. This presentation provided administrative details about the TSUG including contact details and admission costs. It was concluded that members of the group must be employed by companies that use heavy mining equipment, and must also be willing to host meetings, make presentations, and support the common goals of the group. tabs., figs.

76 FR 45741 - Approval and Promulgation of Air Quality Implementation Plans; Pennsylvania; Diesel-Powered Motor...

Science.gov (United States)

2011-08-01

... Promulgation of Air Quality Implementation Plans; Pennsylvania; Diesel-Powered Motor Vehicle Idling Act AGENCY... the Commonwealth's Diesel-Powered Motor Vehicle Idling Act (Act 124 of 2008, or simply Act 124) into... allowable time that heavy-duty, commercial highway diesel vehicles of over 10,000 pounds gross vehicle...

Heavy Vehicle Technologies Program Retrospective and Outlook

International Nuclear Information System (INIS)

James J. Eberhardt

1999-01-01

OHVT Mission is to conduct, in collaboration with our heavy vehicle industry partners and their suppliers, a customer-focused national program to research and develop technologies that will enable trucks and other heavy vehicles to be more energy efficient and able to use alternative fuels while simultaneously reducing emissions

Analysis of a fictive active e- trailer

NARCIS (Netherlands)

Gudo Ebbers; ir. F.G. Rieck; Steven Boonstra

2017-01-01

Trucks, consume an enormous amount of diesel annually and contribute greatly to the total CO2 emission around the world. Electrification of these freight vehicles will lead to reduction of fuel consumption and CO2 emission. Trailers as part of heavy freight vehicles are a great opportunity for

Oxygenated fuels for clean heavy-duty diesel engines

NARCIS (Netherlands)

Frijters, P.J.M.; Baert, R.S.G.

2006-01-01

Abstract: For diesel engines, changing the fuel composition is an alternative route towards achieving lower emission levels. The potential of oxygenated fuels to significantly reduce particulate matter emissions has already been demonstrated earlier. In this study, this research has been

Comparison of Cooling System Designs for an Exhaust Heat Recovery System Using an Organic Rankine Cycle on a Heavy Duty Truck

Directory of Open Access Journals (Sweden)

Nicolas Stanzel

2016-11-01

Full Text Available A complex simulation model of a heavy duty truck, including an Organic Rankine Cycle (ORC based waste heat recovery system and a vehicle cooling system, was applied to determine the system fuel economy potential in a typical drive cycle. Measures to increase the system performance were investigated and a comparison between two different cooling system designs was derived. The base design, which was realized on a Mercedes-Benz Actros vehicle revealed a fuel efficiency benefit of 2.6%, while a more complicated design would generate 3.1%. Furthermore, fully transient simulation results were performed and are compared to steady state simulation results. It is shown that steady state simulation can produce comparable results if averaged road data are used as boundary conditions.

Reduced energy consumption by massive thermoelectric waste heat recovery in light duty trucks

Science.gov (United States)

Magnetto, D.; Vidiella, G.

2012-06-01

The main objective of the EC funded HEATRECAR project is to reduce the energy consumption and curb CO2 emissions of vehicles by massively harvesting electrical energy from the exhaust system and re-use this energy to supply electrical components within the vehicle or to feed the power train of hybrid electrical vehicles. HEATRECAR is targeting light duty trucks and focuses on the development and the optimization of a Thermo Electric Generator (TEG) including heat exchanger, thermoelectric modules and DC/DC converter. The main objective of the project is to design, optimize and produce a prototype system to be tested on a 2.3l diesel truck. The base case is a Thermo Electric Generator (TEG) producing 1 KWel at 130 km/h. We present the system design and estimated output power from benchmark Bi2Te3 modules. We discuss key drivers for the optimization of the thermal-to-electric efficiency, such as materials, thermo-mechanical aspects and integration.

Emission rates of regulated pollutants from on-road heavy-duty diesel vehicles

Science.gov (United States)

Shah, Sandip D.; Johnson, Kent C.; Wayne Miller, J.; Cocker, David R.

Emissions from heavy-duty diesel (HDD) vehicles are affected by many factors. Changes in engine technology, operating mode, fuel properties, vehicle speed and ambient conditions can have significant effects on emission rates of regulated species. This paper presents the results of on-road emissions testing of 11 HDD vehicles (model years 1996-2000) over the ARB Four Phase driving schedule and the urban dynamometer driving schedule (UDDS). Emission rates were found to be highly dependent on vehicle operating mode. Per mile NO x emission rates for vehicle operation at low speeds, in simulated congested traffic, were three times higher per mile emissions then while cruising on the freeway. Comparisons of NO x emission factors to EMFAC baseline emission factors were within 5-40% for vehicles of various model years tested over the UDDS. A comparison of NO x emission factors for a weighted average of the ARB four phase driving schedule yielded values within 17-57% of EMFAC values. Generally, particulate matter (PM) emission rates were lower than EMFAC values.

Role of biodiesel with nanoadditives in port owned trucks and other vehicles for emission reduction

Directory of Open Access Journals (Sweden)

Misra Atulya

2017-01-01

Full Text Available Biodiesel is presently available all over the world and can be produced from several types of biomass. Biodiesel fuels are gaining more and more importance as an attractive alternate fuel in various transport sectors due to their renewable nature and lower pollution impact. However, the ports and the shipping sector are still in the early stage of orientation towards biofuels. In the present work, an experimental investigation on the use of diesterol blend (a mixture of diesel, ethanol with biodiesel with cerium oxide as a nanoadditive (D80JBD15E4S1 + cerium oxide in a compression ignition engine is performed to assess the emission characteristics. The results reveal that the presence of the cerium oxide nanoparticle changes the reaction patterns and heat transfer rate that reduces both the CO and CO2 percentage concentration in the exhaust gas appreciably. Further, the reduction in CO2 emission in the port of Chennai is quantified considering the replacement of neat diesel with those of modified diesel blend in port owned trucks and vehicles.

Medium Truck Duty Cycle Data from Real-World Driving Environments: Final Report

Energy Technology Data Exchange (ETDEWEB)

Lascurain, Mary Beth [ORNL; Franzese, Oscar [ORNL; Capps, Gary J [ORNL; Siekmann, Adam [ORNL; Thomas, Neil [ORNL; LaClair, Tim J [ORNL; Barker, Alan M [ORNL; Knee, Helmut E [ORNL

2012-11-01

Since the early part of the 20th century, the US trucking industry has provided a safe and economical means of moving commodities across the country. At present, nearly 80% of US domestic freight movement involves the use of trucks. The US Department of Energy (DOE) is spearheading a number of research efforts to improve heavy vehicle fuel efficiencies. This includes research in engine technologies (including hybrid and fuel cell technologies), lightweight materials, advanced fuels, and parasitic loss reductions. In addition, DOE is developing advanced tools and models to support heavy vehicle research and is leading the 21st Century Truck Partnership and the SuperTruck development effort. Both of these efforts have the common goal of decreasing the fuel consumption of heavy vehicles. In the case of SuperTruck, a goal of improving the overall freight efficiency of a combination tractor-trailer has been established. This Medium Truck Duty Cycle (MTDC) project is a critical element in DOE s vision for improved heavy vehicle energy efficiency; it is unique in that there is no other existing national database of characteristic duty cycles for medium trucks based on collecting data from Class 6 and 7 vehicles. It involves the collection of real-world data on medium trucks for various situational characteristics (e.g., rural/urban, freeway/arterial, congested/free-flowing, good/bad weather) and looks at the unique nature of medium trucks drive cycles (stop-and-go delivery, power takeoff, idle time, short-radius trips). This research provides a rich source of data that can contribute to the development of new tools for FE and modeling, provide DOE a sound basis upon which to make technology investment decisions, and provide a national archive of real-world-based medium-truck operational data to support energy efficiency research. The MTDC project involved a two-part field operational test (FOT). For the Part-1 FOT, three vehicles each from two vocations (urban transit and

Transportable Heavy Duty Emissions Testing Laboratory and Research Program

Energy Technology Data Exchange (ETDEWEB)

David Lyons

2008-03-31

The objective of this program was to quantify the emissions from heavy-duty vehicles operating on alternative fuels or advanced fuel blends, often with novel engine technology or aftertreatment. In the first year of the program West Virginia University (WVU) researchers determined that a transportable chassis dynamometer emissions measurement approach was required so that fleets of trucks and buses did not need to be ferried across the nation to a fixed facility. A Transportable Heavy-Duty Vehicle Emissions Testing Laboratory (Translab) was designed, constructed and verified. This laboratory consisted of a chassis dynamometer semi-trailer and an analytic trailer housing a full scale exhaust dilution tunnel and sampling system which mimicked closely the system described in the Code of Federal Regulations for engine certification. The Translab was first used to quantify emissions from natural gas and methanol fueled transit buses, and a second Translab unit was constructed to satisfy research demand. Subsequent emissions measurement was performed on trucks and buses using ethanol, Fischer-Tropsch fuel, and biodiesel. A medium-duty chassis dynamometer was also designed and constructed to facilitate research on delivery vehicles in the 10,000 to 20,000lb range. The Translab participated in major programs to evaluate low-sulfur diesel in conjunction with passively regenerating exhaust particulate filtration technology, and substantial reductions in particulate matter were recorded. The researchers also participated in programs to evaluate emissions from advanced natural gas engines with closed loop feedback control. These natural gas engines showed substantially reduced levels of oxides of nitrogen. For all of the trucks and buses characterized, the levels of carbon monoxide, oxides of nitrogen, hydrocarbons, carbon dioxide and particulate matter were quantified, and in many cases non-regulated species such as aldehydes were also sampled. Particle size was also

Impacts and mitigation of excess diesel-related NOx emissions in 11 major vehicle markets

Science.gov (United States)

Anenberg, Susan C.; Miller, Joshua; Minjares, Ray; Du, Li; Henze, Daven K.; Lacey, Forrest; Malley, Christopher S.; Emberson, Lisa; Franco, Vicente; Klimont, Zbigniew; Heyes, Chris

2017-05-01

Vehicle emissions contribute to fine particulate matter (PM2.5) and tropospheric ozone air pollution, affecting human health, crop yields and climate worldwide. On-road diesel vehicles produce approximately 20 per cent of global anthropogenic emissions of nitrogen oxides (NOx), which are key PM2.5 and ozone precursors. Regulated NOx emission limits in leading markets have been progressively tightened, but current diesel vehicles emit far more NOx under real-world operating conditions than during laboratory certification testing. Here we show that across 11 markets, representing approximately 80 per cent of global diesel vehicle sales, nearly one-third of on-road heavy-duty diesel vehicle emissions and over half of on-road light-duty diesel vehicle emissions are in excess of certification limits. These excess emissions (totalling 4.6 million tons) are associated with about 38,000 PM2.5- and ozone-related premature deaths globally in 2015, including about 10 per cent of all ozone-related premature deaths in the 28 European Union member states. Heavy-duty vehicles are the dominant contributor to excess diesel NOx emissions and associated health impacts in almost all regions. Adopting and enforcing next-generation standards (more stringent than Euro 6/VI) could nearly eliminate real-world diesel-related NOx emissions in these markets, avoiding approximately 174,000 global PM2.5- and ozone-related premature deaths in 2040. Most of these benefits can be achieved by implementing Euro VI standards where they have not yet been adopted for heavy-duty vehicles.

Impacts and mitigation of excess diesel-related NOx emissions in 11 major vehicle markets.

Science.gov (United States)

Anenberg, Susan C; Miller, Joshua; Minjares, Ray; Du, Li; Henze, Daven K; Lacey, Forrest; Malley, Christopher S; Emberson, Lisa; Franco, Vicente; Klimont, Zbigniew; Heyes, Chris

2017-05-25

Vehicle emissions contribute to fine particulate matter (PM 2.5 ) and tropospheric ozone air pollution, affecting human health, crop yields and climate worldwide. On-road diesel vehicles produce approximately 20 per cent of global anthropogenic emissions of nitrogen oxides (NO x ), which are key PM 2.5 and ozone precursors. Regulated NO x emission limits in leading markets have been progressively tightened, but current diesel vehicles emit far more NO x under real-world operating conditions than during laboratory certification testing. Here we show that across 11 markets, representing approximately 80 per cent of global diesel vehicle sales, nearly one-third of on-road heavy-duty diesel vehicle emissions and over half of on-road light-duty diesel vehicle emissions are in excess of certification limits. These excess emissions (totalling 4.6 million tons) are associated with about 38,000 PM 2.5 - and ozone-related premature deaths globally in 2015, including about 10 per cent of all ozone-related premature deaths in the 28 European Union member states. Heavy-duty vehicles are the dominant contributor to excess diesel NO x emissions and associated health impacts in almost all regions. Adopting and enforcing next-generation standards (more stringent than Euro 6/VI) could nearly eliminate real-world diesel-related NO x emissions in these markets, avoiding approximately 174,000 global PM 2.5 - and ozone-related premature deaths in 2040. Most of these benefits can be achieved by implementing Euro VI standards where they have not yet been adopted for heavy-duty vehicles.

Surrogate Plant Data Base : Volume 4. Appendix E : Medium and Heavy Truck Manufacturing

Science.gov (United States)

1983-05-01

This four volume report consists of a data base describing "surrogate" automobile and truck manufacturing plants developed as part of a methodology for evaluating capital investment requirements in new manufacturing facilities to build new fleets of ...

40 CFR 86.1920 - What in-use testing information must I report to EPA?

Science.gov (United States)

2010-07-01

... type or application (such as delivery, line haul, or dump truck). Also, identify the type of trailer... (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES (CONTINUED) Manufacturer-Run In-Use Testing Program for Heavy-Duty Diesel Engines § 86.1920 What in-use...

In-vehicle measurement of ultrafine particles on compressed natural gas, conventional diesel, and oxidation-catalyst diesel heavy-duty transit buses.

Science.gov (United States)

Hammond, Davyda; Jones, Steven; Lalor, Melinda

2007-02-01

Many metropolitan transit authorities are considering upgrading transit bus fleets to decrease ambient criteria pollutant levels. Advancements in engine and fuel technology have lead to a generation of lower-emission buses in a variety of fuel types. Dynamometer tests show substantial reductions in particulate mass emissions for younger buses (vehicle particle number concentration measurements on conventional diesel, oxidation-catalyst diesel and compressed natural gas transit buses are compared to estimate relative in-vehicle particulate exposures. Two primary consistencies are observed from the data: the CNG buses have average particle count concentrations near the average concentrations for the oxidation-catalyst diesel buses, and the conventional diesel buses have average particle count concentrations approximately three to four times greater than the CNG buses. Particle number concentrations are also noticeably affected by bus idling behavior and ventilation options, such as, window position and air conditioning.

Experimental investigations of the hydrogen addition effects on diesel engine performance

Science.gov (United States)

Mirica, I.; Pana, C.; Negurescu, N.; Cernat, A.; Nutu, C.

2016-08-01

In the global content regarding the impact on the environmental of the gases emissions resulted from the fossil fuels combustion, an interest aspect discussed on the 21st Session of the Conference of the Parties from the 2015 Paris Climate Conference and the gradual diminution of the worldwide oil reserves contribute to the necessity of searching of alternative energy from durable and renewable resources. At the use of hydrogen as addition in air to diesel engine, the level of CO, HC and smoke from the exhaust gases will decrease due to the improvement of the combustion process. At low and medium partial loads and low hydrogen energetic ratios used the NOX emission level can decrease comparative to classic diesel engine. The hydrogen use as fuel for diesel engine leads to the improving of the energetic and emissions performance of the engine due to combustion improvement and reduction of carbon content. The paper presents, in a comparative way, results of the experimental researches carried on a truck compression ignition engine fuelled with diesel fuel and with hydrogen diesel fuel and hydrogen as addition in air at different engine operation regimes. The results obtained during experimental investigations show better energetic and pollution performance of the engine fuelled with hydrogen as addition in air comparative to classic engine. The influences of hydrogen addition on engine operation are shown.

Test/QA plan for the verification testing of alternative or reformulated liquid fuels, fuel additives, fuel emulsions, and lubricants for highway and nonroad use heavy-duty diesel engines

Science.gov (United States)

This Environmental Technology Verification Program test/QA plan for heavy-duty diesel engine testing at the Southwest Research Institute’s Department of Emissions Research describes how the Federal Test Procedure (FTP), as listed in 40 CFR Part 86 for highway engines and 40 CFR P...

Validated analytical modeling of diesel engine regulated exhaust CO emission rate

Directory of Open Access Journals (Sweden)

Waleed F Faris

2016-06-01

Full Text Available Albeit vehicle analytical models are often favorable for explainable mathematical trends, no analytical model has been developed of the regulated diesel exhaust CO emission rate for trucks yet. This research unprecedentedly develops and validates for trucks a model of the steady speed regulated diesel exhaust CO emission rate analytically. It has been found that the steady speed–based CO exhaust emission rate is based on (1 CO2 dissociation, (2 the water–gas shift reaction, and (3 the incomplete combustion of hydrocarbon. It has been found as well that the steady speed–based CO exhaust emission rate based on CO2 dissociation is considerably less than the rate that is based on the water–gas shift reaction. It has also been found that the steady speed–based CO exhaust emission rate based on the water–gas shift reaction is the dominant source of CO exhaust emission. The study shows that the average percentage of deviation of the steady speed–based simulated results from the corresponding field data is 1.7% for all freeway cycles with 99% coefficient of determination at the confidence level of 95%. This deviation of the simulated results from field data outperforms its counterpart of widely recognized models such as the comprehensive modal emissions model and VT-Micro for all freeway cycles.

Simulation and control of a HD diesel engine equipped with new EGR technology

NARCIS (Netherlands)

Dekker, H.J.; Sturm, W.L.

1996-01-01

A dynamic model of a Heavy Duty (HD) turbocharged and aftercooled diesel engine was developed. The engine was equipped with high pressure diesel injection, a Variable Geometry Turbine (VGT) and an Exhaust Gas Recirculation (EGR) system. This engine was targeted at meeting EURO4 emission

Reducing heat transfer across the insulated walls of refrigerated truck trailers by the application of phase change materials

International Nuclear Information System (INIS)

Ahmed, Mashud; Meade, Oliver; Medina, Mario A.

2010-01-01

A general estimate shows that 80% of communities across the United States receive their goods exclusively by transport trucks, of which a significant number are climate-controlled because they carry perishable goods, pharmaceutical items and many other temperature-sensitive commodities. Keeping the inside of a truck trailer at a constant temperature and relative humidity requires exact amounts of heat and/or moisture management throughout the shipment period, which is regulated via small refrigeration units, placed outside the truck, that operate by burning fuel. These trucks, known as refrigerated truck trailers, are the focus of this paper. In the research presented herein, the conventional method of insulation of the refrigerated truck trailer was modified using phase change materials (PCMs). The limited research carried out in refrigerated transport compared to other refrigeration processes has left spaces for innovative solutions in this area. The research investigated the inclusion of paraffin-based PCMs in the standard trailer walls as a heat transfer reduction technology. An average reduction in peak heat transfer rate of 29.1% was observed when all walls (south, east, north, west, and top) were considered. For individual walls, the peak heat transfer rate was reduced in the range of 11.3-43.8%. Overall average daily heat flow reductions into the refrigerated compartment of 16.3% were observed. These results could potentially translate into energy savings, pollution abatement from diesel-burning refrigeration units, refrigeration equipment size reduction, and extended equipment operational life. The research and its results will help to better understand the scope of this technology.

The injection equipment of future high-speed DI diesel engines with respect to power and pollution requirements

Energy Technology Data Exchange (ETDEWEB)

Dolenc, A. (Monobloc Dieselmotoren GmbH, Vienna (AT))

1990-01-01

The development of high specific output DI diesel engines started at the low-speed end some 50 years ago primarily for marine and traction applications. Movement towards the high-speed end has been slow but steady with the majority of truck engines being very conservatively rated. There has been recent major effort on the automotive car and light commercial vehicle diesel application leading to lightweight DI diesel engines with an engine speed of 4000-5000 r/min and a rated power of 50 kW/litre displacement. These are expected to be on the market in a short period of time. The key point of this development has been the injection equipment including combustion control. In this area the use of modulated injection has the possibility of solving power and pollution requirements. (author).

Potential ozone impacts of excess NO2 emissions from diesel particulate filters for on- and off-road diesel engines.

Science.gov (United States)

Bar-llan, Amnon; Johnson, Jeremiah R; Denbleyker, Allison; Chan, Lit-Mian; Yarwood, Gregory; Hitchcock, David; Pinto, Joseph P

2010-08-01

This study considers potential impacts of increased use of diesel oxidation catalysts (DOCs) and catalyzed diesel particulate filters (DPFs) on ozone formation in the Dallas/ Fort Worth (DFW) area. There is concern that excess nitrogen dioxide (NO2) emissions from vehicles equipped with these devices could increase ambient ozone levels. The approach involved developing two scenarios for use of these devices, quantifying excess NO2 emissions in each scenario, and using a photochemical model to estimate the resulting ozone changes. In the "maximum penetration" scenario, DOC/DPF devices in a 2009 fleet of heavy-duty on-road trucks, school buses, and construction equipment were significantly increased by accelerating turnover of these vehicles and equipment to models that would require DOCs/DPFs. In the "realistic" scenario, current fractional usage of these devices was assessed for 2009. For both scenarios, excess NO2 emissions from DOCs/DPFs were estimated using U.S. Environmental Protection Agency's MOBILE6 and NONROAD emissions inventory modeling tools. The emissions analyses were used to adjust the DFW photochemical modeling emissions inventories and the Comprehensive Air Quality Model with extensions air quality model was rerun for the DFW area to determine the impact of these two scenarios on ozone formation. The maximum penetration scenario, which showed an overall reduction in oxides of nitrogen (NO(x)) because of the accelerated turnover of equipment to cleaner models, resulted in a net decrease in daily maximum 8-hr ozone of 4-5 parts per billion (ppb) despite the increase in NO2 emissions. The realistic scenario resulted in a small increase in daily maximum 8-hr ozone of less than 1 ppb for the DFW area. It was concluded that the excess NO2 emissions from DOC/DPF devices result in very small ozone impacts, particularly for the realistic scenario, in the DFW area. There are noticeable decreases in ozone for the maximum penetration scenario because NO

Effects of particulate oxidation catalyst on unregulated pollutant emission and toxicity characteristics from heavy-duty diesel engine.

Science.gov (United States)

Feng, Xiangyu; Ge, Yunshan; Ma, Chaochen; Tan, Jianwei

2015-01-01

To evaluate the effects of particulate oxidation catalyst (POC) on unregulated pollutant emission and toxicity characteristics, polycyclic aromatic hydrocarbons (PAHs), volatile organic compounds (VOCs), soot, soluble organic fractions (SOF) and sulphate emissions emitted from a heavy-duty diesel engine retrofitted with a POC were investigated on a diesel bench. The particulate matter (PM) in the exhaust was collected by Teflon membrane, and the PAHs and VOCs were analysed by a gas chromatography/mass spectrometer (GC/MS). The results indicate that the POC exhibits good performance on the emission control of VOCs, PAHs and PM. The POC and the diesel particulate filters (DPF) both show a good performance on reducing the VOCs emission. Though the brake-specific emission (BSE) reductions of the total PAHs by the POC were lower than those by the DPF, the POC still removed almost more than 50% of the total PAHs emission. After the engine was retrofitted with the POC, the reductions of the PM mass, SOF and soot emissions were 45.2-89.0%, 7.8-97.7% and 41.7-93.3%, respectively. The sulphate emissions decreased at low and medium loads, whereas at high load, the results were contrary. The PAHs emissions were decreased by 32.4-69.1%, and the contributions of the PAH compounds were affected by the POC, as well as by load level. The benzo[a]pyrene equivalent (BaPeq) of PAHs emissions were reduced by 35.9-97.6% with the POC. The VOCs emissions were reduced by 21.8-94.1% with the POC, and the reduction was more evident under high load.

Environmental Assessment: Military Housing Privatization Initiative at Scott Air Force Base, Illinois

Science.gov (United States)

2005-09-01

OUTDOOR NOISE SOURCES NOISE LEVEL (dBA) COMMON INDOOR NOISE LEVELS COMMON OUTDOOR NOISE LEVELS Gas Lawn Mower at 3 ft. Diesel Truck at 50 ft. Noise...Urban Daytime Gas Lawn Mower at 100 ft. Commercial Area Heavy Traffic at 300 ft. Quiet Urban Daytime Quiet Urban Nighttime Quiet Rural Nighttime Quiet

Environmental Assessment: Anti-Terrorism/Force Protection at Grand Forks Air Force Base, North Dakota

Science.gov (United States)

2003-09-01

OUTDOOR NOISE SOURCES NOISE LEVEL (dBA) COMMON INDOOR NOISE LEVELS COMMON OUTDOOR NOISE LEVELS Gas Lawn Mower at 3 ft. Diesel Truck at 50 ft. Noise...Urban Daytime Gas Lawn Mower at 100 ft. Commercial Area Heavy Traffic at 300 ft. Quiet Urban Daytime Quiet Urban Nighttime Quiet Rural Nighttime Quiet

Effect of Weight and Roadway Grade on the Fuel Economy of Class-8 Frieght Trucks

Energy Technology Data Exchange (ETDEWEB)

Franzese, Oscar [ORNL; Davidson, Diane [ORNL

2011-11-01

In 2006-08, the Oak Ridge National Laboratory, in collaboration with several industry partners, collected real-world performance and situational data for long-haul operations of Class-8 trucks from a fleet engaged in normal freight operations. Such data and information are useful to support Class-8 modeling of combination truck performance, technology evaluation efforts for energy efficiency, and to provide a means of accounting for real-world driving performance within combination truck research and analyses. The present study used the real-world information collected in that project to analyze the effects that vehicle speed and vehicle weight have on the fuel efficiency of Class-8 trucks. The analysis focused on two type of terrains, flat (roadway grades ranging from -1% to 1%) and mild uphill terrains (roadway grades ranging from 1% to 3%), which together covered more than 70% of the miles logged in the 2006-08 project (note: almost 2/3 of the distance traveled on mild uphill terrains was on terrains with 1% to 2% grades). In the flat-terrain case, the results of the study showed that for light and medium loads, fuel efficiency decreases considerably as speed increases. For medium-heavy and heavy loads (total vehicle weight larger than 65,000 lb), fuel efficiency tends to increase as the vehicle speed increases from 55 mph up to about 58-60 mph. For speeds higher than 60 mph, fuel efficiency decreases at an almost constant rate with increasing speed. At any given speed, fuel efficiency decreases and vehicle weight increases, although the relationship between fuel efficiency and vehicle weight is not linear, especially for vehicle weights above 65,000 lb. The analysis of the information collected while the vehicles were traveling on mild upslope terrains showed that the fuel efficiency of Class-8 trucks decreases abruptly with vehicle weight ranging from light loads up to medium-heavy loads. After that, increases in the vehicle weight only decrease fuel

HEAVY-DUTY GREENHOUSE GAS EMISSIONS MODEL ...

Science.gov (United States)

Class 2b-8 vocational truck manufacturers and Class 7/8 tractor manufacturers would be subject to vehicle-based fuel economy and emission standards that would use a truck simulation model to evaluate the impact of the truck tires and/or tractor cab design on vehicle compliance with any new standards. The EPA has created a model called “GHG Emissions Model (GEM)”, which is specifically tailored to predict truck GHG emissions. As the model is designed for the express purpose of vehicle compliance demonstration, it is less configurable than similar commercial products and its only outputs are GHG emissions and fuel consumption. This approach gives a simple and compact tool for vehicle compliance without the overhead and costs of a more sophisticated model. Evaluation of both fuel consumption and CO2 emissions from heavy-duty highway vehicles through a whole-vehicle operation simulation model.

Modelling Truck Weigh Stations’ Locations based on Truck Traffic Flow and Overweight Violation: A Case Study in Bosnia and Herzegovina

Directory of Open Access Journals (Sweden)

Mirsad Kulović

2018-04-01

Full Text Available The number of registered commercial freight vehicles is constantly increasing, increasing therefore as well the traffic load on the roads in Bosnia and Herzegovina. A significant part of freight vehicles moving along the main and regional roads are overloaded and cause significant damage to road infrastructure, affect road safety and result in an increase of emissions of harmful gases for people and the environment. The overloading rate is extremely high, in particular with 5-axle trucks representing 58.7%. The research showed that the increased overload level ranges from 10-20% of the maximum permissible weight. The importance of load limits was recognized early in the history of road development. This interrelation led directly to limitations on vehicle loads, and laws were enacted in many countries to establish the maximum allowable motor vehicle sizes and weights. Strict enforcement of motor vehicle size and weight laws is a step toward reducing motor vehicle size and weight violations, heavy truck accidents, and, even more, improving road maintenance, rehabilitation expenditures and road safety. Thus, based on the applied model the objective of this paper is to evaluate and optimize the locations of truck weigh stations on the road network of Bosnia and Herzegovina.

Evaluating the effects of heavy sugar cane truck operations on repair cost of low volume highways : technical summary report.

Science.gov (United States)

2008-10-01

Current Louisiana state laws allow truck operators hauling certain agricultural commodities to purchase : overweight permits and haul at gross vehicle weights (GVW) in excess of the legislated GVW limit of : 80,000 lb. For instance, sugar cane trucke...

Environmental Assessment: Sooner Drop Zone Expansion Altus Air Force Base, Oklahoma

Science.gov (United States)

2003-08-01

AND OUTDOOR NOISE SOURCES NOISE LEVEL (dBA) COMMON INDOOR NOISE LEVELS COMMON OUTDOOR NOISE LEVELS Jet Flyover at 1000 ft. Gas Lawn Mower at 3 ft...Diesel Truck at 50 ft. Noise Urban Daytime Gas Lawn Mower at 100 ft. Commercial Area Heavy Traffic at 300 ft. Quiet Urban Daytime Quiet Urban Nighttime

Rotary kiln and batch pyrolysis of waste tire to produce gasoline and diesel like fuels

International Nuclear Information System (INIS)

Ayanoğlu, Abdulkadir; Yumrutaş, Recep

2016-01-01

Highlights: • Waste Tire Oil (WTO) is produced from waste tire at rotary kiln reactor. • Physical and chemical properties of WTO and fuel samples are analyzed. • Gasoline like fuel (GLF) and diesel like fuel (DLF) are produced from the WTO-10 wt% CaO mixture at fixed bed reactor. • Physical and chemical properties of the GLF and DLF are compared with the standard fuels. - Abstract: In this study, waste tire is pyrolyzed in a rotary kiln reactor to obtain more gas, light liquid, heavy liquid, wax products, and less carbon black at their maximum yields as, 20%, 12%, 25%, 8% and 35% of the total weight (4 tones), respectively. Then, the heavy and light oils are reacted with additives such as natural zeolite (NZ) and lime (CaO) at different mass ratio as 2, 6, and 10 wt%, respectively, in the batch reactor to produce liquids similar to standard petroleum fuels. The heavy and light oils mixture samples are distillated to observe their optimum graphics which are similar to gasoline and diesel like fuel. Consequently, the best results are obtained from the CaO sample with 10 wt% in comparison to the ones from the gasoline and diesel fuels. The 10 wt% CaO light liquid mixture resembles to gasoline named as gasoline like fuel (GLF) and the 10 wt% CaO heavy liquid mixture is similar to diesel called as diesel like fuel (DLF). The chemical and physical features of the waste tire, light oil, heavy oil, GLF, and DLF are analyzed by TG (thermogravimetric)/dTG (derivative thermogravimetric), proximate, ultimate, higher heating value (HHV), fourier transform-infrared spectroscopy (FT-IR), Brunauer–Emmett–Teller (BET), sulfur, density, viscosity, gas chromatography–mass spectroscopy (GC–MS), flash point, moisture, and distillation tests. The test results are turned out to be very close to the standard petroleum fuel.

Kogi Truck Culture

OpenAIRE

Choy, Vivian

2011-01-01

Food trucks have become a large phenomenon in many parts of Southern California. In fact, the University of California, Los Angeles had begun permitting several food trucks to park on campus for hungry students, in response to the closure of the Bombshelter, a major campus food court. These trucks’ budding popularity has been spurred by the notable Kogi Trucks, which began its business serving those in Los Angeles. To explore the heart of this Kogi hype, I took two trips to the intersectio...

A new alternative paraffinic-palmbiodiesel fuel for reducing polychlorinated dibenzo-p-dioxin/dibenzofuran emissions from heavy-duty diesel engines.

Science.gov (United States)

Lin, Yuan-Chung; Liu, Shou-Heng; Chen, Yan-Min; Wu, Tzi-Yi

2011-01-15

Polychlorinated dibenzo-p-dioxin/dibenzofuran (PCDD/F) emissions from heavy-duty diesel engines (HDDEs) fuelled with paraffinic-palmbiodiesel blends have been rarely addressed in the literature. A high-resolution gas chromatograph/high-resolution mass spectrometer (HRGC/HRMS) was used to analyze 17 PCDD/F species. Experimental results indicate that the main species of PCDD/Fs were OCDD (octachlorinated debenzo-p-dioxin) and OCDF (octachlorodibenzofuran), and they accounted for 40-50% of the total PCDD/Fs for all test fuels. Paraffinic-palmbiodiesel blends decreased PCDD/Fs by 86.1-88.9%, toxic PCDD/Fs by 91.9-93.0%, THC (total hydrocarbons) by 13.6-23.3%, CO (carbon monoxide) by 27.2-28.3%, and PM (particulate matter) by 21.3-34.2%. Using biodiesel blends, particularly BP9505 or BP8020, instead of premium diesel fuel (PDF) significantly reduced emissions of both PCDD/Fs and traditional pollutants. Using BP9505 (95vol% paraffinic fuel+5vol% palmbiodiesel) and BP8020 instead of PDF can decrease PCDD/F emissions by 5.93 and 5.99gI-TEQyear(-1) in Taiwan, respectively. Copyright © 2010. Published by Elsevier B.V.

Review of Heavy-Duty Engine Combustion Research at Sandia National Laboratories

International Nuclear Information System (INIS)

Robert W. Carling; Gurpreet Singh

2000-01-01

The objectives of this paper are to describe the research efforts in diesel engine combustion at Sandia National Laboratories' Combustion Research Facility and to provide recent experimental results. We have four diesel engine experiments supported by the Department of Energy, Office of Heavy Vehicle Technologies: a one-cylinder version of a Cummins heavy-duty engine, a diesel simulation facility, a one-cylinder Caterpillar engine to evaluate combustion of alternative fuels, and a homogeneous-charge, compression-ignition (HCCI) engine facility is under development. Recent experimental results to be discussed are: the effects of injection timing and diluent addition on late-combustion soot burnout, diesel-spray ignition and premixed-burn behavior, a comparison of the combustion characteristics of M85 (a mixture of 85% methanol and 15% gasoline) and DF2 (No.2 diesel reference fuel), and a description of our HCCI experimental program and modeling work

Comparisons of system benefits and thermo-economics for exhaust energy recovery applied on a heavy-duty diesel engine and a light-duty vehicle gasoline engine

International Nuclear Information System (INIS)

Wang, Tianyou; Zhang, Yajun; Zhang, Jie; Peng, Zhijun; Shu, Gequn

2014-01-01

Highlights: • Comparisons of exhaust energy recovery are launched between two types of engine. • System performances are analyzed in terms of benefits and thermo-economics. • Diesel engine system presents superior to gasoline type in economic applicability. • Only diesel engine system using water under full load meets the economic demand. - Abstract: Exhaust energy recovery system (EERS) based on Rankine cycle (RC) in internal combustion engines have been studied mainly on heavy-duty diesel engines (D) and light-duty vehicle gasoline engines (G), however, little information available on systematical comparisons and evaluations between the two applications, which is a particularly necessary summary for clarifying the differences. In this paper, the two particular systems are compared quantitatively using water, R141b, R123 and R245fa as working fluids. The influences of evaporating pressure, engine type and load on the system performances are analyzed with multi-objectives, including the thermal efficiency improvement, the reduced CO 2 emission, the total heat transfer area per net power output (APP), the electricity production cost (EPC) and the payback period (PBP). The results reveal that higher pressure and engine load would be attractive for better performances. R141b shows the best performances in system benefits for the D-EERS, while water exhibits the largest contributions in the G-EERS. Besides, water performs the best thermo-economics, and R245fa serves as the most uneconomical fluid. The D-EERS presents superior to the G-EERS in the economic applicability as well as much more CO 2 emission reductions, although with slightly lower thermal efficiency improvement, and only the D-EERS with water under the full load meets the economic demand. Therefore the EERS based on RC serve more applicable on the heavy-duty diesel engine, while it might be feasible for the light-duty vehicle gasoline engine as the state-of-the art technologies are developed in the

Modeling the selective catalytic reduction of NOx by ammonia over a Vanadia-based catalyst from heavy duty diesel exhaust gases

International Nuclear Information System (INIS)

Yun, Byoung Kyu; Kim, Man Young

2013-01-01

A numerical simulation for prediction of NO X conversion over a commercial V 2 O 5 catalyst with NH 3 as a reductant was performed for a heavy duty diesel engine applications. The chemical behaviors of the SCR reactor are described by using the global NO X kinetics including standard, fast, and NH 3 oxidation reactions with the Langmuir–Hinshelwood (LH) mechanism incorporated into the commercial Boost code. After introducing mathematical models for the SCR reaction with specific reaction parameters, the effects of various parameters such as space velocities, the O 2 , H 2 O, NO 2 , and NH 3 concentrations on the NOx conversion are thoroughly studied and validated by comparing with the experimental data available in the literature. It is found that NO X conversion increases with decreasing space velocity, H 2 O concentration, and NH 3 /NO X ratio, and increasing O 2 concentration and NO 2 /NO X ratio. The study shows that not only is the present approach adopted is flexible in treating performance of the commercial V 2 O 5 based SCR catalyst, it is also accurate and efficient for the prediction of NO X conversion in diesel exhaust environments. - Highlights: ► To find the reaction parameters for LH mechanism over a commercial V2O5 catalyst. ► To investigate the effects of various parameters on the SCR NO X conversion. ► To present benchmark solutions on SCR behavior with diesel exhaust environments.

Isolation and Characterization of Phenanthrene Degrading Bacteria from Diesel Fuel-Contaminated Antarctic Soils

Directory of Open Access Journals (Sweden)

Alejandro Gran-Scheuch

2017-08-01

Full Text Available Antarctica is an attractive target for human exploration and scientific investigation, however the negative effects of human activity on this continent are long lasting and can have serious consequences on the native ecosystem. Various areas of Antarctica have been contaminated with diesel fuel, which contains harmful compounds such as heavy metals and polycyclic aromatic hydrocarbons (PAH. Bioremediation of PAHs by the activity of microorganisms is an ecological, economical, and safe decontamination approach. Since the introduction of foreign organisms into the Antarctica is prohibited, it is key to discover native bacteria that can be used for diesel bioremediation. By following the degradation of the PAH phenanthrene, we isolated 53 PAH metabolizing bacteria from diesel contaminated Antarctic soil samples, with three of these isolates exhibiting a high phenanthrene degrading capacity. In particular, the Sphingobium xenophagum D43FB isolate showed the highest phenanthrene degradation ability, generating up to 95% degradation of initial phenanthrene. D43FB can also degrade phenanthrene in the presence of its usual co-pollutant, the heavy metal cadmium, and showed the ability to grow using diesel-fuel as a sole carbon source. Microtiter plate assays and SEM analysis revealed that S. xenophagum D43FB exhibits the ability to form biofilms and can directly adhere to phenanthrene crystals. Genome sequencing analysis also revealed the presence of several genes involved in PAH degradation and heavy metal resistance in the D43FB genome. Altogether, these results demonstrate that S. xenophagum D43FB shows promising potential for its application in the bioremediation of diesel fuel contaminated-Antarctic ecosystems.

NOx Emissions from Diesel Passenger Cars Worsen with Age.

Science.gov (United States)

Chen, Yuche; Borken-Kleefeld, Jens

2016-04-05

Commonly, the NOx emissions rates of diesel vehicles have been assumed to remain stable over the vehicle's lifetime. However, there have been hardly any representative long-term emission measurements. Here we present real-driving emissions of diesel cars and light commercial vehicles sampled on-road over 15 years in Zurich/Switzerland. Results suggest deterioration of NOx unit emissions for Euro 2 and Euro 3 diesel technologies, while Euro 1 and Euro 4 technologies seem to be stable. We can exclude a significant influence of high-emitting vehicles. NOx emissions from all cars and light commercial vehicles in European emission inventories increase by 5-10% accounting for the observed deterioration, depending on the country and its share of diesel cars. We suggest monitoring the stability of emission controls particularly for high-mileage light commercial as well as heavy-duty vehicles.

Emissions of PCDD/Fs, PCBs, and PAHs from legacy on-road heavy-duty diesel engines.

Science.gov (United States)

Laroo, Christopher A; Schenk, Charles R; Sanchez, L James; McDonald, Joseph; Smith, Peter L

2012-11-01

Exhaust emissions of seventeen 2,3,7,8-substituted polychlorinated dibenzo-p-dioxin/furan (PCDD/F) congeners, tetra-octa PCDD/F homologues, 12 WHO 2005 polychlorinated biphenyl (PCB) congeners, mono-nona chlorinated biphenyl homologues, and 19 polycyclic aromatic hydrocarbons (PAHs) from three legacy diesel engines were investigated. The three engines tested were a 1985 model year GM 6.2J-series engine, a 1987 model year Detroit Diesel Corporation 6V92 engine, and a 1993 model year Cummins L10 engine. Results were compared to United States' mobile source inventory for on-road diesel engines, as well as historic and modern diesel engine emission values. The test fuel contained chlorine at 9.8 ppm which is 1.5 orders of magnitude above what is found in current diesel fuel and 3900 ppm sulfur to simulate fuels that would have been available when these engines were produced. Results indicate PCDD/F emissions of 13.1, 7.1, and 13.6 pg International Toxic Equivalency (I-TEQ)L(-1) fuel consumed for the three engines respectively, where non-detects are equal to zero. This compares with a United States' mobile source on-road diesel engine inventory value of 946 pg I-TEQL(-1) fuel consumed and 1.28 pg I-TEQL(-1) fuel consumed for modern engines equipped with a catalyzed diesel particle filter and urea selective catalytic reduction. PCB emissions are 2 orders of magnitude greater than modern diesel engines. PAH results are representative of engines from this era based on historical values and are 3-4 orders of magnitude greater than modern diesel engines. Published by Elsevier Ltd.

Emission reduction in diesel hybrid commercial vehicles; Emissionsreduzierung bei NFZ mit Dieselhybridantrieb

Energy Technology Data Exchange (ETDEWEB)

Kuberczyk, Raffael; Koehler, Jochen; Blattner, Stefan [ZF Friedrichshafen AG, Friedrichshafen (Germany)

2013-03-01

As far as the commercial vehicle driveline is concerned, today's formidable challenges are combined with an equally compelling need for action - all geared to the aim of meeting stringent emissions standards which reduce fuel consumption and emissions. At the same time the costs for sophisticated new exhaust emissions systems should be reduced. In the following, engineers from ZF Friedrichshafen AG illustrate the advantages offered by diesel hybrid trucks - and why a comprehensive analysis of all saving potentials is required to meet the ambitious targets. (orig.)

Scrotal neoplasia: would truck drivers be at greater risk?

Directory of Open Access Journals (Sweden)

Daniel Seabra

2007-08-01

Full Text Available OBJECTIVE: To analyze how scrotal neoplasias have been managed during the past decade and to question possible factors or professions associated to its presence. MATERIALS AND METHODS: We retrospectively evaluated every case reported from 1995 to 2005 at our hospital. We described the clinical scenario, complementary exams, treatments and outcomes. We also tried to verify if there was any risk, predisposing factors or professions that would explain the cancer origin. RESULTS: Six cases were reviewed. Out of these, three patients were truck drivers. Five of them showed restricted lesions without inguinal lymph nodes enlargement. Histologically, six patients presented squamous carcinoma, with two of them having the verrucous type. The median age of patients was 52 years old (31 to 89. The five patients who are still alive had their lesions completely removed with safety margin and primary closure. CONCLUSIONS: We have noticed that the scrotal carcinoma behavior is similar to that of the penis, where removal of the lesion and study of the regional lymph nodes help to increase the patient survival rate. The outstanding fact was that three out of six patients were truck drivers, raising the hypothesis that such profession, maybe due to the contact or attrition with the diesel exhaust expelled by the engine or to sexual promiscuity, would imply in a larger risk of developing this rare neoplasia.

Optical strain measurement for fault detection in haul-truck tires

International Nuclear Information System (INIS)

Kotchon, A; Nobes, D S; Lipsett, M G

2012-01-01

Tire condition is integral to the safe operation of heavy machinery, such as ultra-class haul trucks. A new approach to haul truck tire monitoring is being investigated based on optical strain measurement, which has the advantage of providing quantitative information from sensors that do not contact the tire. A laboratory-scale apparatus has been constructed to monitor a tire as it is subjected to various loads and pressures. Digital image correlation is used to calculate the deformation in the tire. Using this method, damage resulting from a horizontal and vertical cut created on the tire surface could be detected. A three-dimensional surface reconstruction of the tire was created to assist in the characterization of more complex damage types such as wear and fatigue. In addition to providing information for a possible industrial scale damage detection system, this apparatus will also further the understanding of damage mechanisms in tires.

Interstate Electrification Improvement Project

Energy Technology Data Exchange (ETDEWEB)

Puckette, Margaret [Shorepower Technologies, Hillsboro, OR (United States); Kim, Jeff [Shorepower Technologies, Hillsboro, OR (United States)

2015-07-01

The Interstate Electrification Improvement Project, publicly known as the Shorepower Truck Electrification Project (STEP), started in May 2011 and ended in March 2015. The project grant was awarded by the Department of Energy’s Vehicles Technology Office in the amount of $22.2 million. It had three overarching missions: 1. Reduce the idling of Class 8 tractors when parked at truck stops, to reduce diesel fuel consumption and thus U.S. dependence on foreign petroleum; 2. Stimulate job creation and economic activity as part of the American Reinvestment and Recovery Act of 2009; 3. Reduce greenhouse gas emissions (GHG) from diesel combustion and the carbon footprint of the truck transportation industry. The project design was straightforward. First, build fifty Truck Stop Electrification (TSE) facilities in truck stop parking lots across the country so trucks could plug-in to 110V, 220V, or 480VAC, and shut down the engine instead of idling. These facilities were strategically located at fifty truck stops along major U.S. Interstates with heavy truck traffic. Approximately 1,350 connection points were installed, including 150 high-voltage electric standby Transport Refrigeration Unit (eTRU) plugs--eTRUs are capable of plugging in to shore power1 to cool the refrigerated trailer for loads such as produce, meats and ice cream. Second, the project provided financial incentives on idle reduction equipment to 5,000 trucks in the form of rebates, to install equipment compatible with shore power. This equipment enables drivers to shut down the main engine when parked, to heat or cool their cab, charge batteries, or use other household appliances without idling—a common practice that uses approximately 1 gallon of diesel per hour. The rebate recipients were intended to be the first fleets to plug into Shorepower to save diesel fuel and ensure there is significant population of shore power capable trucks. This two part project was designed to complement each other by

METHODOLOGY, ASSUMPTIONS, AND BASELINE DATA FOR THE REPOSITORY DESIGN AND OPERATION, RAIL CORRIDORS, AND HEAVY TRUCK ROUTES, CLARK COUNTY, NEVADA, LINCOLN COUNTY, NEVADA, NYE COUNTY, NEVADA, ''REST OF NEVADA'', STATE OF NEVADA

International Nuclear Information System (INIS)

2002-01-01

This document was prepared in support of the ''Environmental Impact Statement for a Geologic Repository for the Disposal of Spent Nuclear Fuel and High-Level Radioactive Waste at Yucca Mountain; Nye County, Nevada''. Specifically, the document evaluates potential socioeconomic impacts resulting from the various rail corridor and heavy haul truck route implementing alternatives, one of which would be selected to transport the nation's commercial and defense spent nuclear fuel and high-level radioactive waste to the proposed repository

Potential air toxics hot spots in truck terminals and cabs.

Science.gov (United States)

Smith, Thomas J; Davis, Mary E; Hart, Jaime E; Blicharz, Andrew; Laden, Francine; Garshick, Eric

2012-12-01

loading dock and mechanic shop. Finally, we conducted a detailed descriptive analysis of the real-time data collected in the yard and in truck cabs during the six repeat site visits, which included more than 50 12-hour sessions at each sampling location. The real-time yard monitoring results suggested that under some conditions there was a clear upwind-to-downwind trend indicating a terminal contribution, which was not apparent in the integrated sampling data alone. They also suggested a nonlinear relationship with wind speed: calm conditions (wind speed 10 mph) favored dilution and dispersal (more so for VOCs than for PM). Finally, an analysis of the real-time data for driver exposures in trucks with a global positioning system (GPS) matched with geographic information system (GIS) data suggested a clear influence of traffic and industrial sources along a given route with peaks in driver exposures. These peaks were largely associated with traffic, major intersections, idling at the terminals, and pickup and delivery (P&D) periods. However, VOCs and PM2.5 had different exposure patterns: VOCs exposures increased when the vehicle was stopped, and PM2.5 exposures increased during travel in traffic. All three types of testing sites--upwind and downwind fence-line locations and inside truck cabs while in heavy traffic--met the established definition for a hot spot by having periods with concentrations of pollutants that exceeded the EPA's screening values. Most frequently, the pollutants with concentrations exceeding the screening values were formaldehyde, acetaldehyde, and EC (which serves as a marker for diesel particulate); less frequently they were 1,3-butadiene and benzene. In the case of the downwind location of a single truck terminal without an aggregation of other sources, high concentrations of VOCs and PM were infrequent. Using structural equation modeling, a model was developed that could identify combinations of conditions and factors likely to produce hot spots

Supercritical fluid chromatography and high temperature liquid chromatography for the group-type separation of diesel fuels and heavy gas oils

Energy Technology Data Exchange (ETDEWEB)

Paproski, R.E.

2008-07-01

This thesis investigated the use of unconventional extraction columns for separating diesel fuels by supercritical fluid chromatography (SFC) and for separating heavy gas oils by high temperature normal phase high performance liquid chromatography (HPLC). The purpose was to improve group-type resolution of the fuels, although these methods are also commonly used to determine the proportion of saturates, mono-, di-, tri-, and polyaromatic hydrocarbons. Higher mobile phase flow rates and unconventional column dimensions were also studied to obtain faster analysis times with both SFC and HPLC. The highest group-type resolutions with SFC were obtained by serially coupling bare titania and bare silica columns. Short packed columns and monolithic silica columns were compared at high carbon dioxide flow rates for reducing SFC analysis time, with shortpacked columns achieving 7-fold lower separation times while maintaining significant resolution. Three diesel samples had better resolution and analysis time. A thermally stable bare zircoma column for normal phase HPLC was studied at temperatures up to 200 degrees C. An increase in temperature resulted in lower retention of twenty five aromatic model compounds. Considerable improvements in peak shape, efficiency, group-type selectivity, and column re-equilibration times were obtained at elevated temperatures. At temperatures over 100 degrees C, indole and carbazole thermally decomposed in a hexane/dichloromethane mobile phase. The first order decomposition of carbazole was studied in further detail. A high resolution method was developed using titania and silica columns with valve-switching and dual gradients to separate 3 heavy gas oils. Separation was achieved in only 3 minutes using a fast analysis time method in a titania column at high flow rates.

Marginal abatement cost curves for Heavy Duty Vehicles. Background report

Energy Technology Data Exchange (ETDEWEB)

Schroten, A.; Warringa, G.; Bles, M.

2012-09-15

Cost curves were calculated for CO2 abatement technologies for Heavy Duty Vehicles. These curves were elaborated for eight different vehicle categories (six categories of truck and two subcategories), as well as for an 'average' truck and bus. Given that cost curves depend very much on underlying assumptions, the MACH model (Marginal Abatement Costs of Heavy duty vehicles) was developed. This model allows users to enter their own assumptions with respect to parameters like fuel prices and cost and lifetime of individual technologies, with the model then generating new cost curves for the various vehicle categories. This background report contains a description of the model and a summary of the results of several model runs.

Benefit of energy absorption by the truck in a frontal car-to-truck collision

NARCIS (Netherlands)

Coo, P.J.A. de; Adalian, C.

2000-01-01

EEVC Working Group 14 is investigating the effect of fixing energy absorbing front underrun protection systems (eaFUPS) to trucks instead of rigid devices in order to reduce the injury severity to car occupants in car-to-truck frontal collisions. Three car-to-truck crash tests with cars from

Estimates of the Number of Workers Exposed to Diesel Engine Exhaust in South Korea from 1993 to 2013

Directory of Open Access Journals (Sweden)

Sangjun Choi

2016-12-01

Conclusion: The DEE prevalence rates we surveyed (1.3–19.8% were higher than the primary prevalence rates. The most common emission sources of DEE were diesel engine vehicles such as forklifts, trucks, and vans. Our estimated numbers of workers exposed to DEE can be used to identify industries with workers requiring protection from potential exposure to DEE in the Republic of Korea.

Urban air chemistry and diesel vehicles emissions: Quantifying small and big hydrocarbons by CIMS to improve emission inventories

Science.gov (United States)

Jobson, B. T.; Derstroff, B.; Edtbauer, A.; VanderSchelden, G. S.; Williams, J.

2017-10-01

Emissions from vehicles are a major source of volatile organic compounds (VOCs) in urban environments. Photochemical oxidation of VOCs emitted from vehicle exhaust contributes to O3 and PM2.5 formation, harmful pollutants that major urban areas struggle to control. How will a shift to a diesel engine fleet impact urban air chemistry? Diesel vehicles are a growing fraction of the passenger vehicle fleet in Europe as a result of a deliberate policy to reduce energy consumption and CO2 emissions from the transportation sector (Sullivan et al., 2004). In countries such as France the diesel passenger fleet was already ∼50% of the total in 2009, up from 20% in 1995. Dunmore et al. (2015) have recently inferred that in London, HO radical loss rates to organic compounds is dominated by diesel engine emissions. In the US, increasingly more stringent vehicles emission standards and requirement for improved energy efficiency means spark ignition passenger vehicle emissions have declined significantly over the last 20 years, resulting in the urban diesel fleet traffic (freight trucks) having a growing importance as a source of vehicle pollution (McDonald et al., 2013). The recent scandal involving a major car manufacturer rigging emission controls for diesel passenger cars is a reminder that real world emissions of VOCs from diesel engines are not well understood nor thoroughly accounted for in air quality modeling.

Diesel vehicles and sustainable mobility in the U.S

International Nuclear Information System (INIS)

Wallington, T.J.; Lambert, C.K.; Ruona, W.C.

2013-01-01

Concerns regarding global warming and energy security have increased the importance of decreasing emissions of CO 2 from vehicles. Diesel vehicles have higher fuel economy and lower CO 2 emissions than their gasoline counterparts. On a well-to-wheels per vehicle per km basis it has been estimated that diesel light-duty vehicles in 2015 will emit 14–27% less CO 2 than their gasoline counterparts. We estimate here that on a gCO 2 /kWh at peak torque, diesel medium-duty vehicles currently have an approximately 10% CO 2 advantage over their gasoline counterparts. At light and moderate loads the CO 2 advantage for medium-duty diesels with SCR after-treatment will be greater than 10% (reflecting pumping losses when gasoline engines are operated at low and moderate loads). Emission of NO x , HCs, and PM from diesel (and gasoline) vehicles has decreased substantially over the past decade and further reductions are anticipated in the future. In addition to the heavy-duty segment, which diesels currently dominate, modern diesel engines are likely to continue to play an important role in the medium-duty segment, and perhaps also in the light-duty segment in a transition to more sustainable mobility. - Highlights: ► This paper is part of a special issue on diesels organized by Lee Schipper. ► The paper provides an overview of advanced diesel technology from a U.S. perspective. ► Modern diesel engines are likely to contribute to a transition to more sustainable mobility

The impact of hybrid engines on fuel consumption and emissions of heavy-duty trucks

NARCIS (Netherlands)

Bal, F; Vleugel, J.M.; Brebbia, CA; Sendra, J

2017-01-01

Overland transport of goods mainly goes by road. Road freight transport, trucking in particular, has a large share in the energy consumption, CO2-emissions and air pollution by human activities. This will become an even bigger issue with the expected massive growth of road freight

INFORMATION-MEASURING TEST SYSTEM OF DIESEL LOCOMOTIVE HYDRAULIC TRANSMISSIONS

Directory of Open Access Journals (Sweden)

I. V. Zhukovytskyy

2015-08-01

Full Text Available Purpose. The article describes the process of developing the information-measuring test system of diesel locomotives hydraulic transmission, which gives the possibility to obtain baseline data to conduct further studies for the determination of the technical condition of diesel locomotives hydraulic transmission. The improvement of factory technology of post-repair tests of hydraulic transmissions by automating the existing hydraulic transmission test stands according to the specifications of the diesel locomotive repair enterprises was analyzed. It is achieved based on a detailed review of existing foreign information-measuring test systems for hydraulic transmission of diesel locomotives, BelAZ earthmover, aircraft tug, slag car, truck, BelAZ wheel dozer, some brands of tractors, etc. The problem for creation the information-measuring test systems for diesel locomotive hydraulic transmission is being solved, starting in the first place from the possibility of automation of the existing test stand of diesel locomotives hydraulic transmission at Dnipropetrovsk Diesel Locomotive Repair Plant "Promteplovoz". Methodology. In the work the researchers proposed the method to create a microprocessor automated system of diesel locomotives hydraulic transmission stand testing in the locomotive plant conditions. It acts by justifying the selection of the necessary sensors, as well as the application of the necessary hardware and software for information-measuring systems. Findings. Based on the conducted analysis there was grounded the necessity of improvement the plant hydraulic transmission stand testing by creating a microprocessor testing system, supported by the experience of developing such systems abroad. Further research should be aimed to improve the accuracy and frequency of data collection by adopting the more modern and reliable sensors in tandem with the use of filtering software for electromagnetic and other interference. Originality. The

Investigation of a Novel Coaxial Power-Split Hybrid Powertrain for Mining Trucks

Directory of Open Access Journals (Sweden)

Weiwei Yang

2018-01-01

Full Text Available Due to the different working conditions and specification requirements of mining trucks when compared to commercial passenger vehicles, better fuel efficiency of mining trucks could lead to more significant economic benefits. Therefore, investigating a hybrid transmission system becomes essential. A coaxial power-split hybrid powertrain system for mining trucks is presented in this paper. The system is characterized as comprising an engine, a generator (MG1, a motor (MC2, two sets of planetary gears, and a clutch (CL1. There are six primary operation modes for the hybrid system including the electric motor mode, the engine mode, the hybrid electric mode, the hybrid and assist mode, the regenerative mode, and the stationary charging mode. The mathematical model of the coaxial power-split hybrid system is established according to the requirements of vehicle dynamic performance and fuel economy performance in a given driving cycle. A hybrid vehicle model based on a rule-based control strategy is established to evaluate the fuel economy. Compared with the Toyota Hybrid System (THS and the conventional mechanical vehicle system using a diesel engine, the simulation results based on an enterprise project indicate that the proposed hybrid system can enhance the vehicle’s fuel economy by 8.21% and 22.45%, respectively, during the given mining driving cycle. The simulation results can be used as a reference to study the feasibility of the proposed coaxial hybrid system whose full potential needs to be further investigated by adopting non-causal control strategies.

Comparative measurement of the efficiency of catalytic after-burning devices on a heavy-duty diesel engine

Energy Technology Data Exchange (ETDEWEB)

Pattas, K.N.; Kyriakis, N.A.; Samaras, Z.C.; Aidarinis, J.K.

1984-01-01

The effect of three oxidation catalysts (Honeycat DEP 290, Engelhard PTX 623, Herapur 20L) and one catalytic trap oxidizer (Johnson Matthey JM 13/II) on the emissions of a RABA (M.A.N. Licensed) heavy-duty diesel engine has been comparatively studied. Tests were conducted according to EPA 13 mode test to measure CO, total HC, NO/sub x/ and total particulate matter emitted by the engine with and without devices. The test results were also correlated to the total emissions of the Athenian buses through new weighing factors of an ''Athenian 13 mode test''. The engine tests for all four devices resulted in: (1) considerable reduction of the engine's CO and total HC emissions - being already low (2) practically no difference in NO/sub x/ emissions and (3) increase of the total particulate emissions at high load modes.

75 FR 28820 - Notice of Public Meeting by Teleconference Concerning Heavy Duty Diesel Engine Consent Decrees

Science.gov (United States)

2010-05-24

... implementation of the provisions of the seven consent decrees signed by the United States and diesel engine..., or anticipates receiving, requests from the diesel engine manufacturers for termination of their respective decrees. This meeting notice is also available on EPA's Diesel Engine Settlement Web site at http...

A Comparative Study of the Effect of Turbocompounding and ORC Waste Heat Recovery Systems on the Performance of a Turbocharged Heavy-Duty Diesel Engine

OpenAIRE

Amin Mahmoudzadeh Andwari; Apostolos Pesiridis; Vahid Esfahanian; Ali Salavati-Zadeh; Apostolos Karvountzis-Kontakiotis; Vishal Muralidharan

2017-01-01

In this study the influence of utilization of two Waste Heat Recovery (WHR) strategies, namely organic Rankine cycle (ORC) and turbocompounding, have been investigated based on the performance of a heavy-duty diesel engine using 1-D simulation engine code (GT-Power) in terms of Brake Specific Fuel Consumptions (BSFC) at various engine speeds and Brake Mean Effective Pressures (BMEP). The model of a 6-cylinder turbocharged engine (Holset HDX55V) was calibrated using an experimental BSFC map to...

PM, NOx and butane emissions from on-road vehicle fleets in Hong Kong and their implications on emission control policy

Science.gov (United States)

Ning, Zhi; Wubulihairen, Maimaitireyimu; Yang, Fenhuan

2012-12-01

Vehicular emissions are the major sources of air pollution in urban areas. For metropolitan cities with large population working and living in environments with direct traffic impact, emission control is of great significance to protect public health. Implementation of more stringent emission standards, retrofitting fleet with emission control devices and switching to clearer fuel has been commonly practiced in different cities including Hong Kong. The present study employed a new plume chasing method for effective and quick evaluation of on-road fleet emission factors of particulate matter (PM), nitrogen oxides (NOx), and butane from heavy duty diesel trucks, diesel buses and liquefied petroleum gas (LPG) vehicles. The results showed distinct profiles of the emissions from different fleets with excessive butane emissions from LPG fleet and contrasting PM and NOx emissions from diesel trucks and buses fleets. A cross comparison was also made with emission data from other cities and from historic local studies. The implications of the observed difference on the effectiveness of emission control measures and policy are discussed with recommendations of direction for future research and policy making.

The analysis of loading losses from tank trucks

Directory of Open Access Journals (Sweden)

Jovanović Ana P.

2006-01-01

Full Text Available The quantity of loading losses, which are the primary source of evaporative emissions from tank cars and trucks was analyzed in this paper. Loading losses occur as organic vapors in "empty" cargo tanks are displaced to the atmosphere by the liquid being loaded into the tanks. Emissions from loading petroleum liquid were estimated using three methods: the API (American Petroleum Institute method, the VDI (Verein Deutscher Ingenieure -Association of German Engineers method and the Yugoslav Standard JUS B.HO.531 method. The mass of evaporative losses from loading operations is a function of the following parameters: the method of loading the cargo, the physical and chemical characteristics of the cargo and the ambient temperature during loading. Evaporation losses from the loading of motor gasoline (MB-95, BMB-95, MB-98 and MB-86 and diesel fuels (D-2, Euro D-2 were calculated. Losses on a monthly and annual basis were presented for an assumed amount of loaded cargo. It was estimated that the highest loading losses occur in the summer period because of high ambient daily temperatures and in the period of higher transporting levels. It should be pointed out that the loading losses of diesel fuel calculated using an empirical coefficient according to JUS B.HO.531 are significantly higher in comparison with the loading losses calculated using emission factors from the EPA and the VDI method. The gasoline loading losses calculated using emission factors derived from the three methods are similar.

Advanced Collaborative Emissions Study Auxiliary Findings on 2007-Compliant Diesel Engines: A Comparison With Diesel Exhaust Genotoxicity Effects Prior to 2007

Directory of Open Access Journals (Sweden)

Lance M Hallberg

2017-06-01

Full Text Available Since its beginning, more than 117 years ago, the compression-ignition engine, or diesel engine, has grown to become a critically important part of industry and transportation. Public concerns over the health effects from diesel emissions have driven the growth of regulatory development, implementation, and technological advances in emission controls. In 2001, the United States Environmental Protection Agency and California Air Resources Board issued new diesel fuel and emission standards for heavy-duty engines. To meet these stringent standards, manufacturers used new emission after-treatment technology, and modified fuel formulations, to bring about reductions in particulate matter and nitrogen oxides within the exhaust. To illustrate the impact of that technological transition, a brief overview of pre-2007 diesel engine exhaust biomarkers of genotoxicity and health-related concerns is provided, to set the context for the results of our research findings, as part of the Advanced Collaborative Emissions Study (ACES, in which the effects of a 2007-compliant diesel engine were examined. In agreement with ACES findings reported in other tissues, we observed a lack of measurable 2007-compliant diesel treatment–associated DNA damage, in lung tissue (comet assay, blood serum (8-hydroxy-2′-deoxyguanosine [8-OHdG] assay, and hippocampus (lipid peroxidation assay, across diesel exhaust exposure levels. A time-dependent assessment of 8-OHdG and lipid peroxidation also suggested no differences in responses across diesel exhaust exposure levels more than 24 months of exposure. These results indicated that the 2007-compliant diesel engine reduced measurable reactive oxygen species–associated tissue derangements and suggested that the 2007 standards–based mitigation approaches were effective.

Ride comfort optimization of a multi-axle heavy motorized wheel dump truck based on virtual and real prototype experiment integrated Kriging model

Directory of Open Access Journals (Sweden)

Bian Gong

2015-06-01

Full Text Available The optimization of hydro-pneumatic suspension parameters of a multi-axle heavy motorized wheel dump truck is carried out based on virtual and real prototype experiment integrated Kriging model in this article. The root mean square of vertical vibration acceleration, in the center of sprung mass, is assigned as the optimization objective. The constraints are the natural frequency, the working stroke, and the dynamic load of wheels. The suspension structure for the truck is the adjustable hydro-pneumatic suspension with ideal vehicle nonlinear characteristics, integrated with elastic and damping elements. Also, the hydraulic systems of two adjacent hydro-pneumatic suspension are interconnected. Considering the high complexity of the engineering model, a novel kind of meta-model called virtual and real prototype experiment integrated Kriging is proposed in this article. The interpolation principle and the construction of virtual and real prototype experiment integrated Kriging model were elucidated. Being different from traditional Kriging, virtual and real prototype experiment integrated Kriging combines the respective advantages of actual test and Computer Aided Engineering simulation. Based on the virtual and real prototype experiment integrated Kriging model, the optimization results, obtained by experimental verification, showed significant improvement in the ride comfort by 12.48% for front suspension and 11.79% for rear suspension. Compared with traditional Kriging, the optimization effect was improved by 3.05% and 3.38% respectively. Virtual and real prototype experiment integrated Kriging provides an effective way to approach the optimal solution for the optimization of high-complexity engineering problems.

Spatial variation in diesel-related elemental and organic PM2.5 components during workweek hours across a downtown core.

Science.gov (United States)

Tunno, Brett J; Shmool, Jessie L C; Michanowicz, Drew R; Tripathy, Sheila; Chubb, Lauren G; Kinnee, Ellen; Cambal, Leah; Roper, Courtney; Clougherty, Jane E

2016-12-15

Capturing intra-urban variation in diesel-related pollution exposures remains a challenge, given its complex chemical mix, and relatively few well-characterized ambient-air tracers for the multiple diesel sources in densely-populated urban areas. To capture fine-scale spatial resolution (50×50m grid cells) in diesel-related pollution, we used geographic information systems (GIS) to systematically allocate 36 sampling sites across downtown Pittsburgh, PA, USA (2.8km 2 ), cross-stratifying to disentangle source impacts (i.e., truck density, bus route frequency, total traffic density). For buses, outbound and inbound trips per week were summed by route and a kernel density was calculated across sites. Programmable monitors collected fine particulate matter (PM 2.5 ) samples specific to workweek hours (Monday-Friday, 7 am-7 pm), summer and winter 2013. Integrated filters were analyzed for black carbon (BC), elemental carbon (EC), organic carbon (OC), elemental constituents, and diesel-related organic compounds [i.e., polycyclic aromatic hydrocarbons (PAHs), hopanes, steranes]. To our knowledge, no studies have collected this suite of pollutants with such high sampling density, with the ability to capture spatial patterns during specific hours of interest. We hypothesized that we would find substantial spatial variation for each pollutant and significant associations with key sources (e.g. diesel and gasoline vehicles), with higher concentrations near the center of this small downtown core. Using a forward stepwise approach, we developed seasonal land use regression (LUR) models for PM 2.5 , BC, total EC, OC, PAHs, hopanes, steranes, aluminum (Al), calcium (Ca), and iron (Fe). Within this small domain, greater concentration differences were observed in most pollutants across sites, on average, than between seasons. Higher PM 2.5 and BC concentrations were found in the downtown core compared to the boundaries. PAHs, hopanes, and steranes displayed different spatial

Emissions of nitrogen oxides and particulates of diesel vehicles

OpenAIRE

Kadijk, G.; Ligterink, N.E.; Mensch, P. van; Spreen, J.S.; Vermeulen, R.J.; Vonk, W.A.

2015-01-01

In real-world conditions, modern Euro VI heavy-duty vehicles produce an average of ten times less nitrogen oxide (NOx)emissions than previous generations of Euro IV and Euro V heavy-duty vehicles. However, Euro 6 passenger cars and light commercial vehicles present an entirely different picture since, despite a continual tightening of European emissions limits, the real-world NOx emissions of new diesel passenger cars and light commercial vehicles have remained virtually unchanged over the la...

Feasibility of landfill gas as a liquefied natural gas fuel source for refuse trucks.

Science.gov (United States)

Zietsman, Josias; Bari, Muhammad Ehsanul; Rand, Aaron J; Gokhale, Bhushan; Lord, Dominique; Kumar, Sunil

2008-05-01

The purpose of this paper is to develop a methodology to evaluate the feasibility of using landfill gas (LFG) as a liquefied natural gas (LNG) fuel source for heavy-duty refuse trucks operating on landfills. Using LFG as a vehicle fuel can make the landfills more self-sustaining, reduce their dependence on fossil fuels, and reduce emissions and greenhouse gases. Acrion Technologies Inc. in association with Mack Trucks Inc. developed a technology to generate LNG from LFG using the CO2 WASH process. A successful application of this process was performed at the Eco Complex in Burlington County, PA. During this application two LNG refuse trucks were operated for 600 hr each using LNG produced from gases from the landfill. The methodology developed in this paper can evaluate the feasibility of three LFG options: doing nothing, electricity generation, and producing LNG to fuel refuse trucks. The methodology involved the modeling of several components: LFG generation, energy recovery processes, fleet operations, economic feasibility, and decision-making. The economic feasibility considers factors such as capital, maintenance, operational, and fuel costs, emissions and tax benefits, and the sale of products such as surplus LNG and food-grade carbon dioxide (CO2). Texas was used as a case study. The 96 landfills in Texas were prioritized and 17 landfills were identified that showed potential for converting LFG to LNG for use as a refuse truck fuel. The methodology was applied to a pilot landfill in El Paso, TX. The analysis showed that converting LFG to LNG to fuel refuse trucks proved to be the most feasible option and that the methodology can be applied for any landfill that considers this option.

Driving R&D for the Next Generation Work Truck; NREL (National Renewable Energy Laboratory)

Energy Technology Data Exchange (ETDEWEB)

Melendez, M.

2015-03-04

Improvements in medium- and heavy-duty work truck energy efficiency can dramatically reduce the use of petroleum-based fuels and the emissions of greenhouse gases. The National Renewable Energy Laboratory (NREL) is working with industry partners to develop fuel-saving, high-performance vehicle technologies, while examining fleet operational practices that can simulateneously improve fuel economy, decrease emissions, and support bottom-line goals.

Development of New Diesel Oxidation and NH3 Slip Catalysts

DEFF Research Database (Denmark)

Hansen, Thomas Klint

Diesel engines used in the transport sector and for other heavy machinery form pollutants during the combustion process. Emission of these pollutants into the atmosphere has harmful consequences on human health and the environment. In order to mitigate these harmful effects, regulations have been...... imposed by environmental protection agencies on the most significant pollutants, including CO, hydrocarbons, NOx, and particulate matter. To reduce emissions to the levels specified by the recent Euro VI regulations, it is necessary to apply catalytic exhaust gas aftertreat-ment systems. A modern diesel...... exhaust aftertreatment system commonly consists of a Pt-based diesel oxidation catalyst (DOC) to oxidize CO and unburnt hydrocarbons to CO2 and H2O, and oxidize NO to NO2. This is followed by the diesel particulate filter (DPF), which entraps particulate matter from the exhaust gas. A solution of urea...

The impact of mass flow and masking on the pressure drop of air filter in heavy-duty diesel engine

Directory of Open Access Journals (Sweden)

Gorji-Bandpy Mofid

2012-04-01

Full Text Available This paper presents a computational fluid dynamics (CFD calculation approach to predict and evaluate the impact of the mass-flow inlet on the pressure drop of turbocharger`s air filtfer in heavy-duty diesel engine. The numerical computations were carried out using a commercial CFD program whereas the inlet area of the air filter consisted of several holes connected to a channel. After entering through the channel, the air passes among the holes and enters the air filter. The effect of masking holes and hydraulic diameter is studied and investigated on pressure drop. The results indicate that pressure drop increase with decreasing of hydraulic diameter and masking of the holes has considerable affect on the pressure drop.

Heavy Vehicles on Minor Highway Bridges

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Nielsen, Søren R. K.; Enevoldsen, I.

of heavier trucks moving at larger speeds, and partly because the authorities want to permit transportation of special heavy goods at a larger part of the road net. These needs will in many cases cause the strengthening of the bridges becomes necessary. In order to keep the expenses of such strengthening...

Vehicle to vehicle communications for trucks.

Science.gov (United States)

2014-01-01

The trucking industry is a critical component of American commerce. The American : Trucking Association estimates that over 80 percent of U.S. communities depend : exclusively on trucking for delivery of their goods and commodities

Heavy metal emissions for Danish road transport

Energy Technology Data Exchange (ETDEWEB)

Winther, M.; Slentoe, E.

2010-04-15

This report presents new heavy metal emission factors for cars, vans, trucks, buses, mopeds and motorcycles for each of the emission sources fuel consumption, engine oil, tyre wear, brake wear and road abrasion. The emission components covered are Arsenic (As), Cadmium (Cd), Chromium (Cr), Copper (Cu), Mercury (Hg), Nickel (Ni), Lead (Pb), Selenium (Se) and Zinc (Zn), all of them relevant for emission reporting to the UNECE CLRTAP (United Nations Economic Commission for Europe Convention on Long Range Transboundary Pollutants) convention. The report also presents a new Danish inventory for the year 2007. The following emissions in total TSP (in brackets) are calculated for the year 2007: As (8 kg), Cd (48 kg), Cr (197 kg), Cu (51 779 kg), Hg (28 kg), Ni (158 kg), Pb (6 989 kg), Se (33 kg) and Zn (28 556 kg). Per vehicle type cars are the most important source of emission for all heavy metal species, followed by vans, trucks, buses and 2-wheelers. By using the detailed emission factors and inventory calculation methods established in the present project, estimates of heavy metal emissions can be made for other years than 2007. (author)

Development of offroad unmanned dump truck navigation system. Dump truck mujin soko system no kaihatsu ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Horii, Z [Nittetsu Mining Co. Ltd., Tokyo (Japan)

1992-08-25

A large offroad unmanned dump truck navigation system has been developed, and is in practical operation mounted on dump trucks at Torigatayama Limestone Quarry of Nittetsu Mining Company. The system functions in a manual dump truck navigation mode, wireless navigation mode, and unmanned control mode. The unmanned control mode further includes a mode to navigate the truck on a predetermined course with its data having been input in a computer and a mode that when the truck was moved on a course under a wireless control, the computer learns the course and drives the truck autonomously thereafter. The safety measures are divided into the hardware safety function to detect abnormalities in brakes and other vehicle parts, and the software safety functions of data communications, sensor action check, and prevention of collision of trucks with each other. The system has resulted in a productivity of average one-way travel distance of 345 m, and average unmanned navigation cycle time of 9 minutes and 26 seconds for a transportation efficiency of 541 t/hour/truck, having reached at least the manned operation level. 4 figs., 1 tab.

Investigating the pros and cons of browns gas and varying EGR on combustion, performance, and emission characteristics of diesel engine.

Science.gov (United States)

Thangaraj, Suja; Govindan, Nagarajan

2018-01-01

The significance of mileage to the fruitful operation of a trucking organization cannot be downplayed. Fuel is one of the biggest variable expenses in a trucking wander. An attempt is made in this research to improve the combustion efficiency of a diesel engine for better fuel economy by introducing hydroxy gas which is also called browns gas or HHO gas in the suction line, without compromising performance and emission. Brown's gas facilitates the air-fuel mixture to ignite faster and efficient combustion. By considering safety and handling issues in automobiles, HHO gas generation by electrolysis of water in the presence of sodium bicarbonate electrolytes (NaHCO 3 ) and usage was explored in this research work over compressed pure hydrogen, due to generation and capacity of immaculate hydrogen as of now confines the application in diesel engine operation. Brown's gas was utilized as a supplementary fuel in a single-cylinder, four-stroke compression ignition (CI) engine. Experiments were carried out on a constant speed engine at 1500 rpm, result shows at constant HHO flow rate of 0.73 liter per minute (LPM), brake specific fuel consumption (BSFC) decreases by 7% at idle load to 16% at full load, and increases brake thermal efficiency (BTE) by 8.9% at minimum load to 19.7% at full load. In the dual fuel (diesel +HHO) operation, CO emissions decreases by 19.4, 64.3, and 34.6% at 25, 50, and 75% load, respectively, and unburned hydrocarbon (UHC) emissions decreased by 11.3% at minimum load to 33.5% at maximum load at the expense of NO x emission increases by 1.79% at 75% load and 1.76% at full load than neat diesel operation. The negative impact of an increase in NO x is reduced by adding EGR. It was evidenced in this experimental work that the use of Brown's gas with EGR in the dual fuel mode in a diesel engine improves the fuel efficiency, performance, and reduces the exhaust emissions.

Optimization of shovel-truck system for surface mining

Energy Technology Data Exchange (ETDEWEB)

Ercelebi, S.G.; Bascetin, A. [Istanbul Technical University, Istanbul (Turkey). Mining Engineering Department

2009-07-15

In surface mining operations, truck haulage is the largest item in the operating costs, constituting 50 to 60% of the total. In order to reduce this cost, it is necessary to allocate and dispatch the trucks efficiently. This paper describes shovel and truck operation models and optimization approaches for the allocation and dispatching of trucks under various operating conditions. Closed queuing network theory is employed for the allocation of trucks and linear programming for the purpose of truck dispatching to shovels. A case study was applied for the Orhaneli open Pit Coal Mine in Turkey. This approach would provide the capability of estimating system performance measures (mine throughput, mean number of trucks, mean waiting time, etc.) for planning purposes when the truck fleet is composed of identical trucks. A computational study is presented to show how choosing the optimum number of trucks and optimum dispatching policy affect the cost of moving material in a truck-shovel system.

Measurement of PM and its chemical composition in real-world emissions from non-road and on-road diesel vehicles

Directory of Open Access Journals (Sweden)

M. Cui

2017-06-01

Full Text Available With the rapid growth in the number of both non-road and on-road diesel vehicles, the adverse effects of particulate matter (PM and its constituents on air quality and human health have attracted increasing attentions. However, studies on the characteristics of PM and its composition emitted from diesel vehicles are still scarce, especially under real-world driving conditions. In this study, six excavators and five trucks that provided a wide range of emission standards and operation modes were tested, and PM emissions and their constituents – including organic carbon (OC, elemental carbon (EC, water-soluble ions (WSIs, elements, and organic species like polycyclic aromatic hydrocarbons (PAHs, n-alkanes, and hopanes – as well as steranes were analyzed and characterized. The average emission factors for PM (EFPM from excavator and truck emissions were 829 ± 806 and 498 ± 234 mg kg−1 fuel, respectively. EFPM and PM constituents were significantly affected by fuel quality, operational mode, and emission standards. A significant correlation (R2 = 0. 79, p < 0. 01 was found between EFPM for excavators and the sulfur contents in fuel. The highest average EFPM for working excavators was 904 ± 979 mg kg−1 fuel as a higher engine load required in this mode. From pre-stage 1 to stage 2, the average EFPM for excavators decreased by 58 %. For trucks, the average non-highway EFPM at 548 ± 311 mg kg−1 fuel was higher than the highway EFPM at 497 ± 231 mg kg−1 fuel. Moreover, the reduction rates were 63.5 and 65.6 % when switched from China II and III to China IV standards, respectively. Generally, the PM composition emitted from excavators was dominated by OC (39. 2 ± 21. 0 % and EC (33. 3 ± 25. 9 %; PM from trucks was dominated by EC (26. 9 ± 20. 8 %, OC (9. 89 ± 12 %, and WSIs (4. 67 ± 5. 74 %. The average OC ∕ EC ratios for

High ash fuels for diesel engines II; Korkean tuhkapitoisuuden omaavan polttoaineen kaeyttoe dieselvoimaloissa II

Energy Technology Data Exchange (ETDEWEB)

Norrmen, E.; Vestergren, R.; Svahn, P. [Wartsila Diesel International Ltd, Vaasa (Finland)

1996-12-01

Heavy fuel oils containing a large amount of ash, that is used in some geographically restricted areas, can cause problems with deposit formation and hot corrosion, leading to burned exhaust gas valves in some diesel engines. The Liekki 2 programs Use of high ash fuel in diesel power plants I and II have been initiated to clarify the mechanisms of deposit formation, and start and propagation of hot corrosion. The aim is to get enough knowledge to enable the development of the Waertsilae diesel engines to be able to handle heavy fuel with a very high ash content. The chemistry, sintering, melting, and corrosiveness of deposits from different part of the diesel engine and on different exhaust valve materials, as well as the chemistry in different depths of the deposit have been investigated. Theories for the mechanisms mentioned above have been developed. Additives changing the sintering/melting point and physical properties of the formed deposits have been screened. Exhaust gas particle measurements have been performed when running on high ash fuel, both without deposit modifying fuel additive and with. The results have been used to verify the ABC (Aerosol Behaviour in Combustion) model, and the particle chemistry and morphology has been examined. Several tests, also high load endurance tests have been run in diesel engines with high ash fuels. (author)

Alternatives to Diesel Fuel in California - Fuel Cycle Energy and Emission Effects of Possible Replacements Due to the TAC Diesel Particulate Decision; FINAL

International Nuclear Information System (INIS)

Christopher L. Saraicks; Donald M. Rote; Frank Stodolsky; James J. Eberhardt

2000-01-01

Limitations on petroleum-based diesel fuel in California could occur pursuant to the 1998 declaration by California's Air Resources Board (CARB) that the particulate matter component of diesel exhaust is a carcinogen, therefore a toxic air contaminant (TAC) subject to the state's Proposition 65. It is the declared intention of CARB not to ban or restrict diesel fuel, per se, at this time. Assuming no total ban, Argonne National Laboratory (ANL) explored two feasible ''mid-course'' strategies, each of which results in some degree of (conventional) diesel displacement. In the first case, with substantial displacement of compression ignition by spark ignition engines, diesel fuel is assumed admissible for ignition assistance as a pilot fuel in natural gas (NG)-powered heavy-duty vehicles. Gasoline demand in California increases by 32.2 million liters (8.5 million gallons) per day overall, about 21 percent above projected 2010 baseline demand. Natural gas demand increases by 13.6 million diesel liter (3.6 million gallon) equivalents per day, about 7 percent above projected (total) consumption level. In the second case, ressionignition engines utilize substitutes for petroleum-based diesel having similar ignition and performance properties. For each case we estimated localized air emission plus generalized greenhouse gas and energy changes. Fuel replacement by di-methyl ether yields the greatest overall reduction in NOx emissions, though all scenarios bring about PM10 reductions relative to the 2010 baseline, with greatest reductions from the first case described above and the least from fuel replacement by Fischer-Tropsch synthetic diesel. Economic implications of vehicle and engine replacement were not formally evaluated

Verification of a level-3 diesel emissions control strategy for transport refrigeration units

Science.gov (United States)

Shewalla, Umesh

Transport Refrigeration Units (TRUs) are refrigeration systems used to control the environment of temperature sensitive products while they are being transported from one place to another in trucks, trailers or shipping containers. The TRUs typically use an internal combustion engine to power the compressor of the refrigeration unit. In the United States TRUs are most commonly powered by diesel engines which vary from 9 to 40 horsepower. TRUs are capable of both heating and cooling. The TRU engines are relatively small, inexpensive and do not use emissions reduction techniques such as exhaust gas recirculation (EGR). A significant number of these engines operate in highly populated areas like distribution centers, truck stops, and other facilities which make them one of the potential causes for health risks to the people who live and work nearby. Diesel particulate matter (PM) is known for its adverse effects on both human beings and the environment. Considering these effects, regulatory bodies have imposed limitations on the PM emissions from a TRU engine. The objective of this study was to measure and analyze the regulated emissions from a TRU engine under both engine out and particulate filter system out conditions during pre-durability (when the filter system was new) and post-durability test (after the filter system was subjected to 1000 hours in-field trial). The verification program was performed by the Center for Alternative Fuel, Engines and Emissions (CAFEE) at West Virginia University (WVU). In this program, a catalyzed silicon carbide (SiC) diesel particulate filter (DPF) was evaluated and verified as a Level-3 Verified Diesel Emissions Control Strategy (VDECS) (. 85% PM reduction) under California Air Resources Board (CARB) regulations 2702 [1]. The emissions result showed that the filter system reduced diesel PM by a percentage of 96 +/- 1 over ISO 8178-C1 [2] cycle and 92 +/- 5 over EPA TRU [3] cycle, qualifying as a Level 3 VDECS. The percentage

Diesel Combustion and Emission Using High Boost and High Injection Pressure in a Single Cylinder Engine

Science.gov (United States)

Aoyagi, Yuzo; Kunishima, Eiji; Asaumi, Yasuo; Aihara, Yoshiaki; Odaka, Matsuo; Goto, Yuichi

Heavy-duty diesel engines have adopted numerous technologies for clean emissions and low fuel consumption. Some are direct fuel injection combined with high injection pressure and adequate in-cylinder air motion, turbo-intercooler systems, and strong steel pistons. Using these technologies, diesel engines have achieved an extremely low CO2 emission as a prime mover. However, heavy-duty diesel engines with even lower NOx and PM emission levels are anticipated. This study achieved high-boost and lean diesel combustion using a single cylinder engine that provides good engine performance and clean exhaust emission. The experiment was done under conditions of intake air quantity up to five times that of a naturally aspirated (NA) engine and 200MPa injection pressure. The adopted pressure booster is an external supercharger that can control intake air temperature. In this engine, the maximum cylinder pressure was increased and new technologies were adopted, including a monotherm piston for endurance of Pmax =30MPa. Moreover, every engine part is newly designed. As the boost pressure increases, the rate of heat release resembles the injection rate and becomes sharper. The combustion and brake thermal efficiency are improved. This high boost and lean diesel combustion creates little smoke; ISCO and ISTHC without the ISNOx increase. It also yields good thermal efficiency.

Chemical characterization and toxicity assessment of fine particulate matters emitted from the combustion of petrol and diesel fuels.

Science.gov (United States)

Wu, Di; Zhang, Fei; Lou, Wenhao; Li, Dan; Chen, Jianmin

2017-12-15

Fuel consumption is one of the major contributors to air pollution worldwide. Plenty of studies have demonstrated that the diesel and petrol exhaust fine particulate matters (FPMs) are associated with increases of various diseases. However, the influences of different fuel types and their chemical components on toxicity have been less investigated. In this study, four kinds of fuels that widely used in China were burned in a laboratory simulation, and the FPMs were collected and analyzed. Transmission electron microscopy showed that black carbon was mainly soot with a dendritic morphology. For light diesel oil, marine heavy diesel oil, 93 octane petrol and 97 octane petrol diesel oil, the emission factors of FPMs were 3.05±0.29, 3.21±0.54, 2.36±0.33, and 2.28±0.25g/kg fuel, respectively. And the emission factors for the "16 US EPA" PAHs of FPM were 0.45±0.20, 0.80±0.22, 1.00±0.20, and 1.05±0.19mg/g FPMs, respectively. Fe is the most abundant metal in these FPMs, and the emission factors of FPMs were 2.58±1.70, 4.45±0.11, 8.18±0.58, and 9.24±0.17mg/g FPMs, respectively. We ranked the cytotoxicity of the FPMs emission from fuels combustion: marine heavy diesel oil>97 octane petrol>93 octane petrol>light diesel oil, and the genotoxicity of FPMs emission from fuels combustion: marine heavy diesel oil>light diesel oil>93 octane petrol>97 octane petrol. Significant correlations were found between PAH concentrations and reactive oxygen species (ROS) generation. Our results demonstrated that fuels exhaust FPMs have strong association with ROS activity, cytotoxicity and genotoxicity. These results indicated that fuels exhaust FPMs pose a potentially serious health, and emphasized the importance of assessing the health risks posed by the particulate pollutants in vehicle exhausts. Copyright © 2017. Published by Elsevier B.V.

Full-scale locomotive dynamic crash testing and correlations : locomotive consist colliding with steel coil truck at grade crossing (test 3).

Science.gov (United States)

2011-09-01

This report presents the test results and finite element correlations of a full-scale dynamic collision between a locomotive and a highway truck loaded with two heavy steel coils. The locomotive consist was moving at 58 miles per hour before it struc...

2015 E-Truck Task Force: Key Barriers Affecting E-Truck Adoption, Industry and Policy Implications, and Recommendations to Move the Market Forward

OpenAIRE

Brotherton, Tom; Gilde, Alycia; Tomic, Jasna

2016-01-01

CALSTART’s E-Truck Task Force (ETTF) produced a report outlining the markets for electric drive trucks (E-Trucks), the prime barriers facing their success and provided key findings and recommendations to support expanding E-Truck adoption. Four key findings have been identified by the E-Truck Task Force as barriers currently affecting the growth and viability of E-Truck sales

Development of a lightweight electric urban delivery truck

Energy Technology Data Exchange (ETDEWEB)

Gillespie, G.; Martin, R.; Vader, S. [Unicell Ltd., Toronto, ON (Canada)

2007-07-15

A study was conducted to develop a lightweight urban parcel delivery vehicle that features a composite material, monocoque low-floor body and a zero-emission electric drive system. The long-term goal of project was to produce a vehicle with an energy efficiency that was nearly 90 per cent better than a conventional delivery vehicle. The objectives of the development phase were to complete the structural design of the composite, monocoque low-floor body. Electric drive options were explored to confirm the feasibility in terms of vehicle range, zero emissions and energy efficiency. This involved characterization of the vehicle duty cycle, development of a computer model of the electric powertrain, and simulations to confirm the vehicle's power and energy requirements. The design of the prototype was validated through testing in accordance with recognized vehicle performance tests and an in-service trial by Purolator Courier Ltd., a major Canadian courier service. Testing of the QuickSider delivery truck included vehicle dynamics, energy consumption, safety compliance, and in-service evaluation. No unacceptable stresses, deflections or resonances were identified in the structure. The vehicle's performance was found to be consistent with design expectations. Dynamometer tests have indicated that the ZEV range of the prototype is greater than the targeted 120 km. The overall energy efficiency of the vehicle was 50 per cent, as compared 11 per cent for a conventional diesel delivery truck. It was concluded that an overall energy efficiency of 75 per cent is achievable in production vehicles if improvements are made to the battery system, drive train, regenerative braking and auxiliary systems. 29 figs., 2 appendices.

PCR+ In Diesel Fuels and Emissions Research

Energy Technology Data Exchange (ETDEWEB)

McAdams, H.T.

2002-04-15

In past work for the U.S. Department of Energy (DOE) and Oak Ridge National Laboratory (ORNL), PCR+ was developed as an alternative methodology for building statistical models. PCR+ is an extension of Principal Components Regression (PCR), in which the eigenvectors resulting from Principal Components Analysis (PCA) are used as predictor variables in regression analysis. The work was motivated by the observation that most heavy-duty diesel (HDD) engine research was conducted with test fuels that had been ''concocted'' in the laboratory to vary selected fuel properties in isolation from each other. This approach departs markedly from the real world, where the reformulation of diesel fuels for almost any purpose leads to changes in a number of interrelated properties. In this work, we present new information regarding the problems encountered in the conventional approach to model-building and how the PCR+ method can be used to improve research on the relationship between fuel characteristics and engine emissions. We also discuss how PCR+ can be applied to a variety of other research problems related to diesel fuels.

Business plan for Gourmet Food Truck in Helsinki

OpenAIRE

Mulmi, Mukesh

2015-01-01

This thesis work is about food truck and food truck industry in Finland. In Finland, Culinary scenes are booming and growing but, the food truck concept is new to Finland. Food truck industry is very young and currently, there is a hype for food truck and people are admiring new cuisines. Author himself is working as a cook. And he is passionate about food and restaurant industry. The main purpose of the thesis was to explore more about food truck industry in Finland and create the busine...

Life cycle assessment of climate impact of Fischer-Tropsch diesel based on peat and biomass

Energy Technology Data Exchange (ETDEWEB)

Holmgren, Kristina; Hagberg, Linus

2009-02-15

By combining biomass gasification and Fischer-Tropsch synthesis it is possible to produce biodiesel. Vapo is investigating the possibilities for a plant where a mixture of different biomass fractions and peat would be used as raw material. In this study the climate impact of such synthetic diesel is calculated in terms of radiative forcing. The calculations show that the following parameters have large impact on the results: the emission factors associated with external power demand (purchased electricity) the use of carbon capture and storage the time perspective used in the analysis the raw material mix (amount of peat vs. amount of forest residues) the reference scenario for the peat production (type of peatland) All the FT-diesel scenarios with a peat input of 90% will have higher climate impact than fossil diesel after 100 years, except when CCS is applied and Swedish electricity mix is assumed for the external power demand. In order to have lower climate impact than conventional diesel after 100 years, the peat input must be significantly lower than the biomass input. Substantial reductions of the climate impact can be achieved by applying CCS. With CCS, all peat based FT-diesel scenarios (except the ones based on 90% peat) result in lower climate impact than fossil diesel after both 100 and 300 years. For scenarios with marginal electricity, the reductions are 50-84% after 100 years compared to conventional diesel. For scenarios with Swedish electricity mix the reductions are 100-135% (i.e. zero or negative radiative forcing). The scenarios in this study are based on the assumption that the biodiesel refinery is located close to a harbour so that transportation of captured CO{sub 2} to a storage site can be made by ship. An inland location would require truck transport or pipelines and the cost, infrastructure and logistics for this might not be feasible

Health promotion in the trucking setting: Understanding Dutch truck drivers' road to healthy lifestyle changes.

Science.gov (United States)

Boeijinga, Anniek; Hoeken, Hans; Sanders, José

2016-10-17

The working environment, the nature of the work, and the characteristics of truck drivers as a social group typically pose great challenges for the truck drivers' health and health promotion activities aiming to improve it. The purpose was to obtain a better understanding of (a) Dutch truck drivers' perceptions of health and lifestyle themes, and (b) the challenges they experience in their pursuit of a more healthy lifestyle, as a guiding framework for the development of health interventions targeting this occupational group. In this qualitative study, we conducted and analyzed 20 semi-structured interviews and seven cases of participant observations with Dutch truck drivers. Grounded theory was used to analyze the data. Our findings illustrate that Dutch truck drivers wish to improve their lifestyle but have unproductive associations with concepts of healthy living as well as a tendency to downplay their health risks. In addition, they experience barriers within their work and personal environment that prevent them from translating their intentions into actual lifestyle changes. Based on the insights derived from the interviews, we discuss recommendations for the development of more effective health promotion interventions for truck drivers.

Integrated emission management for cost optimal EGR-SCR balancing in diesels

NARCIS (Netherlands)

Willems, F.P.T.; Mentink, P.R.; Kupper, F.; Eijnden, E.A.C. van den

2013-01-01

The potential of a cost-based optimization method is experimentally demonstrated on a Euro-VI heavy-duty diesel engine. Based on the actual engine-aftertreatment state, this model-based Integrated Emission Management (IEM) strategy minimizes operational (fuel and AdBlue) costs within emission

Gaseous emissions from a heavy-duty engine equipped with SCR aftertreatment system and fuelled with diesel and biodiesel: Assessment of pollutant dispersion and health risk

Energy Technology Data Exchange (ETDEWEB)

Tadano, Yara S.; Borillo, Guilherme C.; Godoi, Ana Flávia L.; Cichon, Amanda; Silva, Thiago O.B.; Valebona, Fábio B.; Errera, Marcelo R. [Environmental Engineering Department, Federal University of Parana, 210 Francisco H. dos Santos St., Curitiba, PR, 81531-980 Brazil (Brazil); Penteado Neto, Renato A.; Rempel, Dennis; Martin, Lucas [Institute of Technology for Development, Lactec–Leme Division, 01 LothárioMeissner Ave., Curitiba, PR, 80210-170 (Brazil); Yamamoto, Carlos I. [Chemical Engineering Department, Federal University of Parana, 210 Francisco H. dos Santos St., Curitiba, PR, 81531-980 Brazil (Brazil); Godoi, Ricardo H.M., E-mail: rhmgodoi@ufpr.br [Environmental Engineering Department, Federal University of Parana, 210 Francisco H. dos Santos St., Curitiba, PR, 81531-980 Brazil (Brazil)

2014-12-01

The changes in the composition of fuels in combination with selective catalytic reduction (SCR) emission control systems bring new insights into the emission of gaseous and particulate pollutants. The major goal of our study was to quantify NO{sub x}, NO, NO{sub 2}, NH{sub 3} and N{sub 2}O emissions from a four-cylinder diesel engine operated with diesel and a blend of 20% soybean biodiesel. Exhaust fume samples were collected from bench dynamometer tests using a heavy-duty diesel engine equipped with SCR. The target gases were quantified by means of Fourier transform infrared spectrometry (FTIR). The use of biodiesel blend presented lower concentrations in the exhaust fumes than using ultra-low sulfur diesel. NO{sub x} and NO concentrations were 68% to 93% lower in all experiments using SCR, when compared to no exhaust aftertreatment. All fuels increased NH{sub 3} and N{sub 2}O emission due to SCR, a precursor secondary aerosol, and major greenhouse gas, respectively. An AERMOD dispersion model analysis was performed on each compound results for the City of Curitiba, assumed to have a bus fleet equipped with diesel engines and SCR system, in winter and summer seasons. The health risks of the target gases were assessed using the Risk Assessment Information System For 1-h exposure of NH{sub 3}, considering the use of low sulfur diesel in buses equipped with SCR, the results indicated low risk to develop a chronic non-cancer disease. The NO{sub x} and NO emissions were the lowest when SCR was used; however, it yielded the highest NH{sub 3} concentration. The current results have paramount importance, mainly for countries that have not yet adopted the Euro V emission standards like China, India, Australia, or Russia, as well as those already adopting it. These findings are equally important for government agencies to alert the need of improvements in aftertreatment technologies to reduce pollutants emissions. - Highlights: • Emission, dispersion and risk assessment

Combined Aero and Underhood Thermal Analysis for Heavy Duty Trucks

Energy Technology Data Exchange (ETDEWEB)

Vegendla, Prasad [Argonne National Lab. (ANL), Argonne, IL (United States); Sofu, Tanju [Argonne National Lab. (ANL), Argonne, IL (United States); Saha, Rohit [Cummins Inc., Columbus, IN (United States); Madurai Kumar, Mahesh [Cummins Inc., Columbus, IN (United States); Hwang, L. K [Cummins Inc., Columbus, IN (United States)

2017-01-31

Aerodynamic analysis of the medium-duty delivery truck was performed to achieve vehicle design optimization. Three dimensional CFD simulations were carried out for several improved designs, with a detailed external component analysis of wheel covers, side skirts, roof fairings, and rounded trailer corners. The overall averaged aerodynamics drag reduction through the design modifications were shown up to 22.3% through aerodynamic considerations alone, which is equivalent to 11.16% fuel savings. The main identified fuel efficiencies were based on second generation devices, including wheel covers, side skirts, roof fairings, and rounded trailer corners. The important findings of this work were; (i) the optimum curvature radius of the rounded trailer edges found to be 125 mm, with an arc length of 196.3 mm, (ii) aerodynamic drag reduction increases with dropping clearance of side skirts between wheels and ground, and (iii) aerodynamic drag reduction increases with an extension of front bumper towards the ground.

Bioremediation of soil contaminated by diesel oil Biorremediação de solos contaminados por óleo diesel

Directory of Open Access Journals (Sweden)

Fatima Menezes Bento

2003-11-01

Full Text Available Were evaluated natural attenuation, biostimulation and bioaugmentation on the degradation of total petroleum hydrocarbons (TPH in soils contaminated with diesel oil. Bioaugmentation showed the greatest degradation in the light (C12 - C23 fractions (72.7% and heavy (C23 - C40 fractions of TPH (75.2% and natural attenuation was more effective than biostimulation. The greatest dehydrogenase activity was observed upon bioaugmentation of the Long Beach soil (3.3-fold and the natural attenuation of the Hong Kong soil sample (4.0-fold. The number of diesel oil degrading microorganisms and heterotrophic population was not influenced by the bioremediation treatments. The best approach for bioremediation of soil contaminated with diesel oil is the inoculum of microorganisms pre-selected from their own environment.Avaliou-se a degradação de hidrocarbonetos de petróleo (HP em solos contaminados com óleo diesel através da atenuação natural, bioestimulação e bioaumentação. A bioaumentação apresentou a maior degradação da fração leve (72,6% e da fração pesada (75,2% de HP e a atenuação natural foi mais efetiva do que a bioestimulação. A maior atividade da dehidrogenase no solo Long Beach e Hong Kong foi observada nos tratamentos bioaumentação e atenuação natural, respectivamente. O número de microrganismos degradadores de diesel e a população de heterotróficos não foi influenciada pelas técnicas de biorremediação. A melhor performance para a biorremediação do solo contaminado com diesel foi obtida quando foram adicionados microrganismos pré-selecionados do ambiente contaminado.

Selection of Fuel System for Modern Heavy Duty Diesel Engines

Directory of Open Access Journals (Sweden)

G. M. Kukharonok

2004-01-01

Full Text Available Fuel systems of diesel engines have been analyzed. The paper shows components of the systems, peculiarities of their manufacturing process. Difference in efficiency of the systems, their application and market prospects are considered in the paper. While solving problems to design a power installation the essence of fuel system selection is given on the basis of an internal combustion engine.

Statistical description of heavy truck accidents on representative segments of interstate highway

International Nuclear Information System (INIS)

Hartman, W.F.; Davidson, C.A.; Foley, J.T.

1977-01-01

Any quantitative analysis of the risk of transportation accidents requires the use of many different statistical distributions. Included among these are the types of accidents which occur and the severity of these when they do occur. Several previous studies have derived this type of information for truck traffic over U. S. highways in general; these data are not necessarily applicable for the anticipated LMFBR spent fuel cask routes. This report presents data for highway segments representative of the specific LMFBR cask routes which are anticipated. These data are based upon a detailed record-by-record review of filed reports for accidents which occurred along the specified route segments

Test/QA plan for the verification testing of diesel exhaust catalysts, particulate filters and engine modification control technologies for highway and nonroad use diesel engines

Science.gov (United States)

This ETV test/QA plan for heavy-duty diesel engine testing at the Southwest Research Institute’s Department of Emissions Research (DER) describes how the Federal Test Procedure (FTP), as listed in 40 CFR Part 86 for highway engines and 40 CFR Part 89 for nonroad engines, will be ...

An experimental investigation of PAH emissions from a heavy duty diesel engine fuelled with biodiesel and its blend

International Nuclear Information System (INIS)

Shah, A. N.; Shan, G.E.Y.; Wei, T.J.; Hua, L.Z.

2008-01-01

For the comparison of emission of polycyclic aromatic hydrocarbons (PAHs) from diesel biodiesel and its 20% blend with diesel, and their carcinogenic potencies, an experimental study has been conducted on a turbocharged, intercooled and direct injection diesel engine. Total PAHs (solid and gas) from diesel, B20 and B100 at low load were more than those at high loads. Total PAH emissions from the test fuels at the rated speed were more than those at maximum torque speed. Benzo[a] pyrene (BaP) brake specific emission of biodiesel is less than that of diesel. LMW-PAH emissions for the test fuels are all higher than those of MMW and HMW PAH. Biodiesel and B20 reduce both the total Benzo[a] pyrene equivalent concentration (BaP/sub eq/) and the total mean-PAHs as compared to commercial diesel fuel. BSFC of the engine increased but its brake power decreased in the cases of B20 and biodiesel. (author)

Dump truck-related deaths in construction, 1992-2007.

Science.gov (United States)

McCann, Michael; Cheng, Mei-Tai

2012-05-01

Dump trucks are universally used in construction and other industries to haul materials to the location and to remove waste materials. The source for dump truck-related fatality data was the Bureau of Labor Statistics Census of Fatal Occupational Injuries (CFOI) Research File. From 1992 to 2007, 829 construction workers were killed in dump truck-related incidents nationwide. Of those, 336 were dump truck operators with 215 deaths occurring in street and highway incidents. Another 343 deaths involved workers on foot, three-quarters struck by dump trucks. Sixty-four of the construction workers killed were maintaining dump trucks, 22 when caught between the truck frame and a falling dump truck bed. Of the 86 other deaths, 55 involved streets and highways. Recommendations include: (i) improving the reporting of seat belt usage in fatality reports; (ii) requiring use of seat belts; (iii) requiring the use of backup alarms, spotters, or other methods to alert dump truck operators to workers in their blind spots; (iv) prohibiting direct dumping at river banks and embankments; (v) using cameras or radar to enforce stopping at railway crossings; and (xi) enforcing worker safety practices (e.g., lockout/tagout procedures on elevated dump truck beds). Copyright © 2011 Wiley Periodicals, Inc.

Feasibility of using cone penetrometer truck (CPT) to install time domain reflectometry (TDR) and fiber optic slope failure detectors in pavement structures.

Science.gov (United States)

2011-02-01

A new method of cable installation using a heavy-duty Cone Penetration Test : (CPT) truck was developed and practiced successfully in this study. The coaxial and fiber : optic cables were pushed along with the cone rods by the hydraulic system integr...

Determinants of fuel consumption in mining trucks

International Nuclear Information System (INIS)

Dindarloo, Saeid R.; Siami-Irdemoosa, Elnaz

2016-01-01

Analysis of fuel consumption in a large surface mine, during more than 5000 cycles of material transportation, revealed considerable variability in the data. Truck fuel estimation based on the mining truck manufacturers' manuals/estimates is not capable of capturing this variability in the fuel consumption data. Partial least squares regression and autoregressive integrated moving average methods were employed to examine the effect of cyclic activities on fuel consumption, and to recommend relevant remedies for consumption reduction. Proper modifications of the operation can result in improved cycle times. Consequently, minimizing some cyclic activities would enhance energy efficiency. The truck “empty idle time” was a major contributor to unnecessary fuel consumption. Since the truck queues at shovels are a major component of the “empty idle time”, decisions should be reviewed to reduce the truck queues at loading points. Improved dispatching strategies, optimal muck pile shape and size distribution, and improved shovel/loader operator skills are effective preventive measures to minimize truck flow bottlenecks at loading points, and thus to improve energy efficiency at mines. - Highlights: • A large fleet of mining trucks consumes considerable amounts of energy. • Current energy models do not consider the effect of site-specific mining conditions. • A new methodology based on material handling cyclic activities is proposed. • Fuel consumption rates in different truck operating modes are determined. • The new model is compared with the truck manufacturer's energy consumption guideline.

Bio diesel- the Clean, Green Fuel for Diesel Engines

International Nuclear Information System (INIS)

Elkareish, S.M.M.

2004-01-01

Natural, renewable resources such as vegetable oils, animal fats and recycled restaurant greases can be chemically transformed into clean burning bio diesel fuels (1). Just like petroleum diesel, bio diesel operates in combustion-ignition engines. Blends of up to 20% bio diesel (mixed with petroleum diesel fuels) can be used in nearly all diesel equipment and are compatible with most storage and distribution equipment. Using bio diesel in a conventional diesel engine substantially reduces emissions of unburned hydrocarbons, carbon monoxide, sulphates, polycyclic aromatic hydrocarbons, nitrated polycyclic aromatic hydrocarbons, and particulate matter. The use of bio diesel has grown dramatically during the last few years. Egypt has a promising experiment in promoting forestation by cultivation of Jatropha plant especially in luxor and many other sites of the country. The first production of the Egyptian Jatropha seeds oil is now under evaluation to produce a cost-competitive bio diesel fuel

19 CFR 123.41 - Truck shipments transiting Canada.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 1 2010-04-01 2010-04-01 false Truck shipments transiting Canada. 123.41 Section... OF THE TREASURY CUSTOMS RELATIONS WITH CANADA AND MEXICO United States and Canada In-Transit Truck Procedures § 123.41 Truck shipments transiting Canada. (a) Manifest required. Trucks with merchandise...

Shock and vibration environments for a large shipping container during truck transport (Part II)

International Nuclear Information System (INIS)

Magnuson, C.E.

1978-05-01

Purpose of this study was to obtain vibration and shock data during truck shipment of heavy cargo. These data were for use in determining any trends of vibration and shock environments with increased cargo weight. The new data were obtained on a ''piggyback'' basis during truck transport of 249 100N (56,000-pound) cargo which consisted of a spent fuel container and its supporting structure. The truck was driven from Mercury, Nevada, to Albuquerque, New Mexico. The routes traveled were US 95 from Mercury, Nevada, to Las Vegas, Nevada; US 93 from Las Vegas to Kingman, Arizona; and I-40/US 66 from Kingman to Albuquerque, New Mexico. Speeds varied from very slow to 88 km/hr (55 mph). A comparison of data from similar experiments with cargo weights varying from no-load to this load shows that the zero-to-peak acceleration amplitude levels of vibration are highest when trucks carry relatively light loads. This is true for the longitudinal and vertical axes of the vehicles in most frequency bands and for the transverse axis above 700 Hz. The shock response acceleration amplitudes for heavier cargo weights were less severe above 3 Hz in the vertical axis and higher between 8 and 20 Hz in the transverse axis. The highest acceleration amplitude of shock response in the longitudinal axis below about 20 Hz was produced in a trailer having a spring suspension system and carrying the 249 100N (56,000 pounds) load

Efficient EGR technology for future HD diesel engine emission targets

NARCIS (Netherlands)

Baert, R.S.G.; Beckman, D.E.; Veen, A.

1999-01-01

Different systems for achieving short-route cooled EGR on turbocharged and aftercooled heavy-duty diesel engines have been tested on a 12 litre 315 kW engine with 4 valves per cylinder and an electronically controlled unit pump fuel injection system. In all of these systems the exhaust gas was

Mitigating Wind Induced Truck Crashes

Science.gov (United States)

2009-12-25

Dangerous weather and high wind in particular, is a common contributing factor in truck crashes. High wind speeds have been documented as a perennial cause of truck crashes in Kansas and other Great Plains states. The possibility of reducing such cra...

Market Innovation in the Transport and Heavy Vehicle Market

DEFF Research Database (Denmark)

Borgström, Benedikte; Agndal, Henrik; Cui, Lianguang

The purpose is to better understand the interrelatedness of new business models in the truck market and developments in the road transport sector. Based on a three year research project in cooperation with a European heavy vehicle manufacturer, we describe short cases showing some of the business...

Hydraulic Hybrid and Conventional Parcel Delivery Vehicles' Measured Laboratory Fuel Economy on Targeted Drive Cycles

Energy Technology Data Exchange (ETDEWEB)

Lammert, M. P.; Burton, J.; Sindler, P.; Duran, A.

2014-10-01

This research project compares laboratory-measured fuel economy of a medium-duty diesel powered hydraulic hybrid vehicle drivetrain to both a conventional diesel drivetrain and a conventional gasoline drivetrain in a typical commercial parcel delivery application. Vehicles in this study included a model year 2012 Freightliner P100H hybrid compared to a 2012 conventional gasoline P100 and a 2012 conventional diesel parcel delivery van of similar specifications. Drive cycle analysis of 484 days of hybrid parcel delivery van commercial operation from multiple vehicles was used to select three standard laboratory drive cycles as well as to create a custom representative cycle. These four cycles encompass and bracket the range of real world in-use data observed in Baltimore United Parcel Service operations. The NY Composite cycle, the City Suburban Heavy Vehicle Cycle cycle, and the California Air Resources Board Heavy Heavy-Duty Diesel Truck (HHDDT) cycle as well as a custom Baltimore parcel delivery cycle were tested at the National Renewable Energy Laboratory's Renewable Fuels and Lubricants Laboratory. Fuel consumption was measured and analyzed for all three vehicles. Vehicle laboratory results are compared on the basis of fuel economy. The hydraulic hybrid parcel delivery van demonstrated 19%-52% better fuel economy than the conventional diesel parcel delivery van and 30%-56% better fuel economy than the conventional gasoline parcel delivery van on cycles other than the highway-oriented HHDDT cycle.

Impact of reformulated fuels on motor vehicle emissions

Science.gov (United States)

Kirchstetter, Thomas

Motor vehicles continue to be an important source of air pollution. Increased vehicle travel and degradation of emission control systems have offset some of the effects of increasingly stringent emission standards and use of control technologies. A relatively new air pollution control strategy is the reformulation of motor vehicle fuels, both gasoline and diesel, to make them cleaner- burning. Field experiments in a heavily traveled northern California roadway tunnel revealed that use of oxygenated gasoline reduced on-road emissions of carbon monoxide (CO) and volatile organic compounds (VOC) by 23 +/- 6% and 19 +/- 8%, respectively, while oxides of nitrogen (NOx) emissions were not significantly affected. The introduction of reformulated gasoline (RFG) in California led to large changes in gasoline composition including decreases in alkene, aromatic, benzene, and sulfur contents, and an increase in oxygen content. The combined effects of RFG and fleet turnover between summers 1994 and 1997 were decreases in on-road vehicle exhaust emissions of CO, non-methane VOC, and NOx by 31 +/- 5, 43 +/- 8, and 18 +/- 4%, respectively. Although it was difficult to separate the fleet turnover and RFG contributions to these changes, it was clear that the effect of RFG was greater for VOC than for NOx. The RFG effect on exhaust emissions of benzene was a 30-40% reduction. Use of RFG reduced the reactivity of liquid gasoline and gasoline headspace vapors by 23 and 19%, respectively. Increased use of methyl tert-butyl ether in gasoline led to increased concentrations of highly reactive formaldehyde and isobutene in vehicle exhaust. As a result, RFG reduced the reactivity of exhaust emissions by only about 5%. Per unit mass of fuel burned, heavy-duty diesel trucks emit about 25 times more fine particle mass and 15-20 times the number of fine particles compared to light-duty vehicles. Exhaust fine particle emissions from heavy-duty diesels contain more black carbon than particulate

Implementation of exclusive truck facilities

Energy Technology Data Exchange (ETDEWEB)

Fekpe, E. [Battelle Memorial Inst., Columbus, OH (United States). Transportation Market Sector

2007-07-01

This paper discussed the issue of highway congestion, safety, and efficiency in freight movement on highways, with particular reference to the challenge of supporting increasing capacity demand from truck traffic. Innovative and practical solutions are needed to address the growing need for more efficient freight movement while maintaining acceptable levels of safety on highways. The concept of exclusive truck facilities (ETFs) is becoming an attractive option as a feasible strategy to help stabilize traffic flow, reduce congestion, improve safety, enhance transportation system management, improve access to freight facilities, and improve efficiency in freight movement along corridors of national importance. ETFs can either be truck only lanes or truckways. Passenger cars may not use ETFs. However, the use of ETFs could involve high costs of construction, maintenance, and acquisition of additional right of way. A cost-benefit analysis was performed for alternative ETF configurations under different traffic and site characteristics. A set of criteria was then proposed for identifying suitable locations for exclusive truck lanes. It was proposed that ETFs are economically feasible at locations with traffic volume of 100,000 vehicles per day or more and with a truck volume of at least 25 per cent of the traffic. In addition, the rate of truck-involved fatal crashes and level of service should be used to prioritize preliminary candidate locations that satisfy the traffic criteria. Consideration should also be given to the existence of freight terminals, ports, processing centers or regional distribution centres that are close to highways. 11 refs., 1 tab.

Development of compressed natural gas/diesel dual-fuel turbocharged compressed ignition engine

Energy Technology Data Exchange (ETDEWEB)

Shenghua, L.; Ziyan, W.; Jiang, R. [Xi' an Jiaotong Univ. (China). Dept. of Automotive Engineering

2003-09-01

A natural gas and diesel dual-fuel turbocharged compression ignition (CI) engine is developed to reduce emissions of a heavy-duty diesel engine. The compressed natural gas (CNG) pressure regulator is specially designed to feed back the boost pressure to simplify the fuel metering system. The natural gas bypass improves the engine response to acceleration. The modes of diesel injection are set according to the engine operating conditions. The application of honeycomb mixers changes the flowrate shape of natural gas and reduces hydrocarbon (HC) emission under low-load and lowspeed conditions. The cylinder pressures of a CI engine fuelled with diesel and dual fuel are analysed. The introduction of natural gas makes the ignition delay change with engine load. Under the same operating conditions, the emissions of smoke and NO{sub x} from the dual-fuel engine are both reduced. The HC and CO emissions for the dual-fuel engine remain within the range of regulation. (Author)

US Army Qualification of Alternative Fuels Specified in MIL-DTL-83133H for Ground Systems Use. Final Qualification Report: JP-8 Containing Synthetic Paraffinic Kerosene Manufactured Via Fischer-Tropsch Synthesis or Hydroprocessed Esters and Fatty Acids

Science.gov (United States)

2013-09-01

environmental standards, and the Department of Energy (DOE) launched several initiatives to develop a new generation of ‘ultra-clean’ transportation fuels...Expanded Mobility Tactical Truck) – A4 HETS (Heavy Equipment Transporter System) – M1070A1 PLS (Palletized Load System) – A1 DDC 8V92TA 12.0 L...Modulus of Compressibility of Diesel/ Biodiesel /HVO Blends. Energy Fuels. 2011, 26, 1336-1343. 578789 Fuels. Coordinating Research Council, Inc. 2009

Dimethylether. Diesel alternative for the future?; Dimethylether. Dieselalternative der Zukunft?

Energy Technology Data Exchange (ETDEWEB)

Werner, Martin; Wachtmeister, Georg [Technische Univ. Muenchen (Germany). Lehrstuhl fuer Verbrennungskraftmaschinen

2010-07-15

Due to dwindling resources, heavy price volatility and the unilateral dependency on crude oil, the demand for alternatives to diesel and gas fuels is increasing. Dimethylether (DME) seems to present a promising option. Early 2009, within the framework of a six month FVV project (keyword 'DME - Alternative Fuels', purpose No. 1005), a potential analysis of DME as a fuel was carried out at the Chair of Combustion Engines (LVK) at the Technische Universitaet Muenchen (TUM). This paper concludes important information about DME from the point of view of heavy duty engine development. (orig.)

Improving the reliability of emergency diesel generators through sustained maintenance

International Nuclear Information System (INIS)

Reddy, R.

2000-01-01

In Nuclear Power Stations Emergency Diesel Generators are vital safety related equipment which ensures power supply to essential equipment during loss of power. In view of their importance Reliability of Diesel generators should be very high. Since these Diesel generators are standby equipment and operate only during demand or during surveillance checks, their demand failure probability should be very low and once they operate their operational availability should be very high. Madras Atomic Power Station at Kalpakkam, India consists two pressurised heavy water Reactors each rated at 220 MWe. To supply standby power each unit has two Diesel Generators of I 500 kW capacity each. The Diesel Engine is 16 cylinder 'V' type engine and is cranked by Air starting motor and is connected to generator whose rating at 100% load is 1500 KW. During commissioning and in the initial years of operation these Diesel Generators have encountered many problems. Major problem was Diesel Engine failing to start on demand. This was due to non engagement of air motor pinion with ring gear or continued engagement air motor even after the engine had picked up speed and failure of timer to initiate multiple starts after initial incomplete starts Apart from these there were problems like fuel oil leaks, high jacket water temperatures, low fuel oil pressure trips. Another major problem was with excitation system. How these problems were dealt with thereby reducing the demand failure probability and increasing the operational availability are discussed in this paper. (author)

Heavy Vehicle Propulsion Materials: Recent Progress and Future Plans

International Nuclear Information System (INIS)

D. Ray Johnson; Sidney Diamond

2001-01-01

The Heavy Vehicle Propulsion Materials Program provides enabling materials technology for the U.S. DOE Office of Heavy Vehicle Technologies (OHVT). The technical agenda for the program is based on an industry assessment and the technology roadmap for the OHVT. A five-year program plan was published in 2000. Major efforts in the program are materials for diesel engine fuel systems, exhaust aftertreatment, and air handling. Additional efforts include diesel engine valve-train materials, structural components, and thermal management. Advanced materials, including high-temperature metal alloys, intermetallics, cermets, ceramics, amorphous materials, metal- and ceramic-matrix composites, and coatings, are investigated for critical engine applications. Selected technical issues and planned and ongoing projects as well as brief summaries of several technical highlights are given

Comparative bioremediation of soils contaminated with diesel oil by natural attenuation, biostimulation and bioaugmentation.

Science.gov (United States)

Bento, Fatima M; Camargo, Flávio A O; Okeke, Benedict C; Frankenberger, William T

2005-06-01

Bioremediation of diesel oil in soil can occur by natural attenuation, or treated by biostimulation or bioaugmentation. In this study we evaluated all three technologies on the degradation of total petroleum hydrocarbons (TPH) in soil. In addition, the number of diesel-degrading microorganisms present and microbial activity as indexed by the dehydrogenase assay were monitored. Soils contaminated with diesel oil in the field were collected from Long Beach, California, USA and Hong Kong, China. After 12 weeks of incubation, all three treatments showed differing effects on the degradation of light (C12-C23) and heavy (C23-C40) fractions of TPH in the soil samples. Bioaugmentation of the Long Beach soil showed the greatest degradation in the light (72.7%) and heavy (75.2%) fractions of TPH. Natural attenuation was more effective than biostimulation (addition of nutrients), most notably in the Hong Kong soil. The greatest microbial activity (dehydrogenase activity) was observed with bioaugmentation of the Long Beach soil (3.3-fold) and upon natural attenuation of the Hong Kong sample (4.0-fold). The number of diesel-degrading microorganisms and heterotrophic population was not influenced by the bioremediation treatments. Soil properties and the indigenous soil microbial population affect the degree of biodegradation; hence detailed site specific characterization studies are needed prior to deciding on the proper bioremediation method.

Diluted Operation of a Heavy-Duty Natural Gas Engine - Aiming at Improved Effciency, Emission and Maximum Load

OpenAIRE

Kaiadi, Mehrzad

2011-01-01

Most heavy-duty engines are diesel operated. Severe emission regulations, high fuel prices, high technology costs (e.g. catalysts, fuel injection systems) and unsustainably in supplying fuel are enough reasons to convenience engine developers to explore alternative technologies or fuels. Using natural gas/biogas can be a very good alternative due to the attractive fuel properties regarding emission reduction and engine operation. Heavy-duty diesel engines can be easily converted for natur...

Fuel Cell Hydroge Manifold for Lift Trucks

DEFF Research Database (Denmark)

Hosseinzadeh, Elham

. Battery driven lift trucks are being used more and more in different companies to reduce their emissions. However, battery driven lift trucks need long time to recharge and may be out of work for a long time. Fuel cell driven lift trucks diminish this problem and are therefore getting more attention...

Soot and chemiluminescence in diesel combustion of bio-derived, oxygenated and reference fuels

NARCIS (Netherlands)

Klein-Douwel, R.J.H.; Donkerbroek, A.J.; Vliet, A.P. van; Boot, M.D.; Somers, L.M.T.; Baert, R.S.G.; Dam, N.J.; Meulen, J.J. ter

2009-01-01

High-speed imaging, spectroscopy and thermodynamical characterization are applied to an optically accessible, heavy-duty diesel engine in order to compare sooting and chemiluminescence behaviour of bio-derived, oxygenated fuels and various reference fuels. The fuels concerned include the bio-derived

The Myth - Food Truck

OpenAIRE

Otálora Salgado, Esteban

2015-01-01

Food truck de comida típica colombiana fusión que espera solucionar la percepción que se tiene acerca de la comida callejera. Para ello, se ha realizado un estudio donde se identifica el problema y se plantea como solución la creación de un food truck que cumpla con todos los estándares de calidad y a su vez innove.

Exploring Telematics Big Data for Truck Platooning Opportunities

Energy Technology Data Exchange (ETDEWEB)

Lammert, Michael P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Bugbee, Bruce [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Hou, Yi [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Muratori, Matteo [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Holden, Jacob [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Duran, Adam W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Mack, Andrea [Montana State University; Swaney, Eric [Volvo Group

2018-04-03

NREL completed a temporal and geospatial analysis of telematics data to estimate the fraction of platoonable miles traveled by class 8 tractor trailers currently in operation. This paper discusses the value and limitations of very large but low time-resolution data sets, and the fuel consumption reduction opportunities from large scale adoption of platooning technology for class 8 highway vehicles in the US based on telematics data. The telematics data set consist of about 57,000 unique vehicles traveling over 210 million miles combined during a two-week period. 75% of the total fuel consumption result from vehicles operating in top gear, suggesting heavy highway utilization. The data is at a one-hour resolution, resulting in a significant fraction of data be uncategorizable, yet significant value can still be extracted from the remaining data. Multiple analysis methods to estimate platoonable miles are discussed. Results indicate that 63% of total miles driven at known hourly-average speeds happens at speeds amenable to platooning. When also considering availability of nearby partner vehicles, results indicate 55.7% of all classifiable miles driven were platoonable. Analysis also address the availability of numerous partners enabling platoons greater than 2 trucks and the percentage of trucks that would be required to be equipped with platooning equipment to realize more than 50% of the possible savings.

Influence of real-world engine load conditions on nanoparticle emissions from a DPF and SCR equipped heavy-duty diesel engine.

Science.gov (United States)

Thiruvengadam, Arvind; Besch, Marc C; Carder, Daniel K; Oshinuga, Adewale; Gautam, Mridul

2012-02-07

The experiments aimed at investigating the effect of real-world engine load conditions on nanoparticle emissions from a Diesel Particulate Filter and Selective Catalytic Reduction after-treatment system (DPF-SCR) equipped heavy-duty diesel engine. The results showed the emission of nucleation mode particles in the size range of 6-15 nm at conditions with high exhaust temperatures. A direct result of higher exhaust temperatures (over 380 °C) contributing to higher concentration of nucleation mode nanoparticles is presented in this study. The action of an SCR catalyst with urea injection was found to increase the particle number count by over an order of magnitude in comparison to DPF out particle concentrations. Engine operations resulting in exhaust temperatures below 380 °C did not contribute to significant nucleation mode nanoparticle concentrations. The study further suggests the fact that SCR-equipped engines operating within the Not-To-Exceed (NTE) zone over a critical exhaust temperature and under favorable ambient dilution conditions could contribute to high nanoparticle concentrations to the environment. Also, some of the high temperature modes resulted in DPF out accumulation mode (between 50 and 200 nm) particle concentrations an order of magnitude greater than typical background PM concentrations. This leads to the conclusion that sustained NTE operation could trigger high temperature passive regeneration which in turn would result in lower filtration efficiencies of the DPF that further contributes to the increased solid fraction of the PM number count.

Impact of overweight vehicles (with heavy axle loads) on bridge deck deterioration.

Science.gov (United States)

2012-03-01

Bridge deck slabs develop compressive stresses from global flexural deformation and locally from high-level : wheel loads when it is subjected to overweight trucks. This study quantified the impact of overweight vehicles : with heavy axle loads on br...

2007 Canadian vehicle survey : summary report

Energy Technology Data Exchange (ETDEWEB)

Garcha, A.; Norup, S.; Kormylo, A.

2009-09-15

The Canadian vehicle survey is a quarterly survey of vehicle transportation activities in Canada that began in 1999. This report presented the results of the Canadian vehicle survey for 2007. The purpose of the survey is to encourage Canadians to make energy-efficient choices regarding their driving habits. The study shed light on Canadian fuel consumption behaviour, modes of transportation and consumer trends. This report examined the composition of Canada's vehicle fleet, the main characteristics of this fleet, and the patterns of vehicle use. Some behavioural characteristics of Canadian drivers were also discussed. Specific topics that were presented included Canada's on-road vehicle fleet; geographic analysis; light vehicles; heavy vehicles such as medium and heavy trucks; and trip analysis such as road types used by vehicles, rush hour and fuel consumption, and driver's age and gender. It was concluded that vehicles in Canada consumed 31 billion litres of gasoline and 11 billion litres of diesel. In addition, fuel efficiency for heavy trucks increased 21 percent between 2000 and 2007. 15 tabs., 39 figs., 4 appendices.

Kinetic study of diesel soot oxidation: application to simulation of diesel particulate filter regeneration; Etude cinetique de la combustion des suies diesel: application a la modelisation de la regeneration du filtre a particule

Energy Technology Data Exchange (ETDEWEB)

Huguet, Ch.

2005-11-15

Because of their toxicity, soot are considered as the most important pollutant from Diesel engines. The Diesel Particulate Filter (DPF) is widely deployed in Europe to address the significant reductions in particulate emissions required by increasingly stringent emission standards, both for heavy duty vehicles and passenger cars. Such a DPF filtrates above 99% of soot emissions and must be regularly regenerated. The use of additive allows to decrease the soot oxidation temperature to values which can be reached by appropriate engine tuning. The soot addition is a dominant parameter for the development of regeneration strategies. Its influence must be correctly represented by models. This Ph-D was performed at IFP in collaboration with ADEME and was supported by the LCSR at Orleans. The aim of the present research is to develop a kinetic mechanism characteristic of Diesel soot oxidation, which can be integrated into a DPF regeneration model and used for engine control. The oxidation study was based on soot characterisation and reaction kinetics investigations. The samples of Diesel soot were collected, without and with Cerium/Iron additive, by using two engines points representative of two normalized European cycles (ECE and EUDC). Thermal and composition analyses with techniques such as XPS, XRD or TEM were used to determine their physical and chemical properties. Their oxidation kinetics was experimentally studied on a synthetic gas bench (SGB) with a fixed bed reactor. Different tests were performed: temperature-programmed oxidation (TPO), Isothermal oxidation (IO), and sequential oxidation. The results allowed to correlate Diesel soot physical and chemical properties with their oxidation rate. A kinetic model was developed, which is based on global carbon consummation law and distinguishes the oxidation of different soot components. The simulation results agree very well with the experimental results of Diesel soot oxidation. (author)

Heavy Vehicles on Minor Highway Bridges

DEFF Research Database (Denmark)

Kirkegaard, Poul Henning; Nielsen, Søren R. K.; Enevoldsen, I.

of heavier trucks moving at larger speeds, and partly because the authorities want to permit transportation of special heavy goods at a larger part of the road net. These needs will in many cases cause the strengthening of the bridges becomes necessary. In order to keep the expenses of such strengthening...... the results obtained using the numerical models given in details in "Heavy Vehicles on Minor Highway Bridges : dynamic modelling of vehicles and bridges". The models are established using a ordinary vehicle which consists of a 48 t Scania with a 3 axle tractor and a 3 axle trailer, joined in a flexible hinge...

Disturbance rejection in diesel engines for low emissions and high fuel efficiency

NARCIS (Netherlands)

Criens, C. H. A.; Willems, F. P. T.; Van Keulen, T. A. C.; Steinbuch, M.

2015-01-01

This brief presents a novel and time-efficient control design for modern heavy-duty diesel engines using a variable geometry turbine and an exhaust gas recirculation valve. The goal is to simultaneously and robustly achieve low fuel consumption and low emissions of nitrogen oxides (NOx) and

Toxicological properties of emission particles from heavy duty engines powered by conventional and bio-based diesel fuels and compressed natural gas.

Science.gov (United States)

Jalava, Pasi I; Aakko-Saksa, Päivi; Murtonen, Timo; Happo, Mikko S; Markkanen, Ari; Yli-Pirilä, Pasi; Hakulinen, Pasi; Hillamo, Risto; Mäki-Paakkanen, Jorma; Salonen, Raimo O; Jokiniemi, Jorma; Hirvonen, Maija-Riitta

2012-09-29

One of the major areas for increasing the use of renewable energy is in traffic fuels e.g. bio-based fuels in diesel engines especially in commuter traffic. Exhaust emissions from fossil diesel fuelled engines are known to cause adverse effects on human health, but there is very limited information available on how the new renewable fuels may change the harmfulness of the emissions, especially particles (PM). We evaluated the PM emissions from a heavy-duty EURO IV diesel engine powered by three different fuels; the toxicological properties of the emitted PM were investigated. Conventional diesel fuel (EN590) and two biodiesels were used - rapeseed methyl ester (RME, EN14214) and hydrotreated vegetable oil (HVO) either as such or as 30% blends with EN590. EN590 and 100% HVO were also operated with or without an oxidative catalyst (DOC + POC). A bus powered by compressed natural gas (CNG) was included for comparison with the liquid fuels. However, the results from CNG powered bus cannot be directly compared to the other situations in this study. High volume PM samples were collected on PTFE filters from a constant volume dilution tunnel. The PM mass emission with HVO was smaller and with RME larger than that with EN590, but both biofuels produced lower PAH contents in emission PM. The DOC + POC catalyst greatly reduced the PM emission and PAH content in PM with both HVO and EN590. Dose-dependent TNFα and MIP-2 responses to all PM samples were mostly at the low or moderate level after 24-hour exposure in a mouse macrophage cell line RAW 264.7. Emission PM from situations with the smallest mass emissions (HVO + cat and CNG) displayed the strongest potency in MIP-2 production. The catalyst slightly decreased the PM-induced TNFα responses and somewhat increased the MIP-2 responses with HVO fuel. Emission PM with EN590 and with 30% HVO blended in EN590 induced the strongest genotoxic responses, which were significantly greater than those with EN590�

Thermal/structural analysis of radiators for heavy-duty trucks

International Nuclear Information System (INIS)

Mao Shaolin; Cheng, Changrui; Li Xianchang; Michaelides, Efstathios E.

2010-01-01

A thermal/structural coupling approach is applied to analyze thermal performance and predict the thermal stress of a radiator for heavy-duty transportation cooling systems. Bench test and field test data show that non-uniform temperature gradient and dynamic pressure loads may induce large thermal stress on the radiator. A finite element analysis (FEA) tool is used to predict the strains and displacement of radiator based on the solid wall temperature, wall-based fluid film heat transfer coefficient and pressure drop. These are obtained from a computational fluid dynamics (CFD) simulation. A 3D simulation of turbulent flow and coupled heat transfer between the working fluids poses a major difficulty because the range of length scales involved in heavy-duty radiators varies from few millimeters of the fin pitch and/or tube cross-section to several meters for the overall size of the radiator. It is very computational expensive, if not impossible, to directly simulate the turbulent heat transfer between fins and the thermal boundary layer in each tube. In order to overcome the computational difficulties, a dual porous zone (DPZ) method is applied, in which fins in the air side and turbulators in the water side are treated as porous region. The parameters involved in the DPZ method are tuned based on experimental data in prior. A distinguished advantage of the porous medium method is its effectiveness of modeling wide-range characteristic scale problems. A parametric study of the impact of flow rate on the heat transfer coefficient is presented. The FEA results predict the maximum value of stress/strain and target locations for possible structural failure and the results obtained are consistent with experimental observations. The results demonstrate that the coupling thermal/structural analysis is a powerful tool applied to heavy-duty cooling product design to improve the radiator thermal performance, durability and reliability under rigid working environment.

40 CFR 86.004-11 - Emission standards for 2004 and later model year diesel heavy-duty engines and vehicles.

Science.gov (United States)

2010-07-01

.... This section applies to 2004 and later model year diesel HDEs. (a)(1) Exhaust emissions from new 2004 and later model year diesel HDEs shall not exceed the following: (i)(A) Oxides of Nitrogen plus Non... diesel HDE families in any or all of the emissions ABT programs for HDEs, within the restrictions...

Simulation Study of the Effect of Decreasing Truck Traffic Flow on Safety on Almeria-Barcelona Corridor

Energy Technology Data Exchange (ETDEWEB)

Dadashova, B.

2016-07-01

In this paper the effect of truck traffic on road safety has been analyzed through simulation study. The main objective of the study is to quantify the effect of the decreasing average annual daily traffic of heavy duty vehicles (trucks) on road safety. As the road safety indicators the frequency road accidents is considered. The data used in the study were collected from one of the most crowded routes in Spain which connects Almeria (south-east) with Barcelona (northeast). The observed data covers year 2010 and were classified into 2 road types: dual carriageways and toll roads. The estimation was carried out using negative binomial model and Markov Chain Monte Carlo simulation. Using the estimation results new traffic scenarios were proposed where the traffic flow is assumed to change its values. A total of 33 scenarios were proposed and new accidents data were generated through MCMC sampling. The comparison of the simulated and observed accident data shows that the effect of decreasing truck traffic flow could meliorate road safety in the route. The simulation tool could be applied to evaluate the effects of freight modal shift from road to rail. (Author)

Estimating diesel fuel exposure for a plumber repairing an underground pipe.

Science.gov (United States)

Finn, Mary; Stenzel, Mark; Ramachandran, Gurumurthy

2017-04-01

We estimated the diesel fuel exposure of a plumber repairing an underground water line leak at a truck stop. The repair work was performed over three days during which the plumber spent most of his time in a pit filled with a mixture of water and diesel fuel. Thus, the plumber was exposed via both the inhalation and dermal routes. While previously asymptomatic, he was diagnosed with acute renal failure 35 days after working at this site. No measurements were available for estimating either inhalation or dermal exposures or the cumulative dose and, therefore, two different approaches were used that were based on simple models of the exposure scenario. The first approach used the ideal gas law with the vapor pressure of the diesel fuel mixture to estimate a saturation vapor concentration, while the second one used a mass balance of the petroleum hydrocarbon component of diesel fuel in conjunction with the Henry's Law constant for this mixture. These inhalation exposure estimates were then adjusted to account for the limited ventilation in a confined space. The inhalation exposure concentrations predicted when handling the water layer alone is much lower than that expected from the organic layer. This case study illustrates the large differences in inhalation exposure associated with volatile organic layers and aqueous solution containing these chemicals. The estimate of dermal exposure was negligible compared to the inhalation exposure because the skin presents a much smaller surface area of exposure to the contaminant compared to the lungs. The methodology presented here is useful for situations where little information is available for more formal mathematical exposure modeling, but where adjustments to the worst-case exposures, estimated simply, can provide reasonable exposure estimates.

Assessment of bio-fuel options for solid oxide fuel cell applications

Science.gov (United States)

Lin, Jiefeng

Rising concerns of inadequate petroleum supply, volatile crude oil price, and adverse environmental impacts from using fossil fuels have spurred the United States to promote bio-fuel domestic production and develop advanced energy systems such as fuel cells. The present dissertation analyzed the bio-fuel applications in a solid oxide fuel cell-based auxiliary power unit from environmental, economic, and technological perspectives. Life cycle assessment integrated with thermodynamics was applied to evaluate the environmental impacts (e.g., greenhouse gas emission, fossil energy consumption) of producing bio-fuels from waste biomass. Landfill gas from municipal solid wastes and biodiesel from waste cooking oil are both suggested as the promising bio-fuel options. A nonlinear optimization model was developed with a multi-objective optimization technique to analyze the economic aspect of biodiesel-ethanol-diesel ternary blends used in transportation sectors and capture the dynamic variables affecting bio-fuel productions and applications (e.g., market disturbances, bio-fuel tax credit, policy changes, fuel specification, and technological innovation). A single-tube catalytic reformer with rhodium/ceria-zirconia catalyst was used for autothermal reformation of various heavy hydrocarbon fuels (e.g., diesel, biodiesel, biodiesel-diesel, and biodiesel-ethanol-diesel) to produce a hydrogen-rich stream reformates suitable for use in solid oxide fuel cell systems. A customized mixing chamber was designed and integrated with the reformer to overcome the technical challenges of heavy hydrocarbon reformation. A thermodynamic analysis, based on total Gibbs free energy minimization, was implemented to optimize the operating environment for the reformations of various fuels. This was complimented by experimental investigations of fuel autothermal reformation. 25% biodiesel blended with 10% ethanol and 65% diesel was determined to be viable fuel for use on a truck travelling with

Reducing truck emissions at container terminals in a low carbon economy

DEFF Research Database (Denmark)

Chen, Gang; GOVINDAN, Kannan; Golias, Mihalis M.

2013-01-01

This study proposes a methodology to optimize truck arrival patterns to reduce emissions from idling truck engines at marine container terminals. A bi-objective model is developed minimizing both truck waiting times and truck arrival pattern change. The truck waiting time is estimated via...... a queueing network. Based on the waiting time, truck idling emissions are estimated. The proposed methodology is evaluated with a case study, where truck arrival rates vary over time. We propose a Genetic Algorithm based heuristic to solve the resulting problem. Result shows that, a small shift of truck...... arrivals can significantly reduce truck emissions, especially at the gate....

A tough truck for ATLAS

CERN Multimedia

2003-01-01

One of the mobile support structures that will be used to manoeuvre and assemble components of the ATLAS detector in its cavern was put through its paces at the end of July and passed its load tests with flying colours. The tests, which involved the surveyors taking measurements to detect any load-induced mechanical deformations, were carried out in Building 191. "The "truck" has been subjected to static tests with loads of up to 1250 tonnes and can carry and transport on air cushions a nominal load of up to 1000 tonnes at a top speed of 30 cm per minute," explains project leader Tommi Nyman. "It took two weeks to assemble the truck's components, the last of which arrived at CERN on 24 June. It then took a further 20 days to load the truck up for the test." The 8.5 metre-high truck will be used for final assembly of some of the ATLAS components, including the calorimeters, in cavern UX15. This powerful device is the result of a collaboration between CERN and the Henryk Niewodniczanski Institute of Nuclear ...

Cyclic oxygenates : a new class of second-generation biofuels for diesel engines?

NARCIS (Netherlands)

Boot, M.D.; Frijters, P.J.M.; Luijten, C.C.M.; Somers, L.M.T.; Baert, R.S.G.; Donkerbroek, A.J.; Klein-Douwel, R.J.H.; Dam, N.J.

2009-01-01

Combustion behavior of various oxygenated fuels has been studied in a DAF heavy-duty (HD) direct-injection (DI) diesel engine. From these fuels, it is well-known that they lead to lower particle (PM) emissions; however, for a given fuel oxygen mass fraction, there are significant differences in PM

Cyclic oxygenates: a new class of second-generation biofuels for diesel engines?

NARCIS (Netherlands)

Boot, M.; Frijters, P.; Luijten, C.; Somers, B.; Baert, R.S.G.; Donkerbroek, A.; Klein-Douwel, R.J.H.; Dam, N.

2009-01-01

Combustion behavior of various oxygenated fuels has been studied in a DAF heavy-duty (HD) directinjection (DI) diesel engine. From these fuels, it is well-known that they lead to lower particle (PM) emissions; however, for a given fuel oxygen mass fraction, there are significant differences in PM

Diesel particles - a health hazard

Energy Technology Data Exchange (ETDEWEB)

Ege, C.

2004-08-15

To all appearances, small particles belong to the pollutants presenting the biggest health hazards. Particles come especially from diesel-powered vehicles. According to researchers, particles cause thousands of early deaths each year in the big cities in Denmark alone, and up to 1,250 of these deaths could be prevented by fitting particle filters on diesel-powered vehicles. That is more than deaths caused by traffic accidents. Especially the elderly are affected. In addition, the small particles seem to aggravate asthma incidences, including the many children with asthma. What makes the small particles so very dangerous is that they can enter the smallest of vessels of the lungs. There is a solution within sight to this grave health hazard. The solution is called particle filters, but they will not come automatically. It requires initiatives in the form of legislation, green taxes and subsidies. The EU is introducing stricter regulations regarding particle emission from heavy vehicles from 2006, though only for new vehicles. It will therefore take many years to abate the problem this way. In the present pamphlet, the Danish Ecological Council offers a number of specific proposals on how to further the introduction of filters on diesel vehicles. The Danish government has taken a small step in the right direction by establishing a subsidy scheme for particle filters. Yet the amount allocated is too small and, because it is not followed up by setting taxes on polluting vehicles, it will have little effect. (au)

Naturalistic Study of Truck Following Behavior

Science.gov (United States)

2016-04-01

Volpe conducted the Naturalistic study of truck following behavior to gain a better understanding of how trucks follow other vehicles in the real world, with the ultimate goal of supporting the Federal Highway Administration in the development of aut...

System for selection of radiation source transfer trucks

International Nuclear Information System (INIS)

Tanimoto, Yoshinori; Ito, Kojiro.

1970-01-01

A device for selection of trucks each of which load and transfer a radiation source to an irradiation room above a water pool is installed at the end of a pair of rails fixed to the bottom of the pool. This device is equipped with a number of laterally shiftable rail pairs which may be brought into successive alignment with the fixed rails and is adapted to receive, carry and fix a truck on each rail pair. If one of said trucks is selected for irradiation in a desired irradiation room, the rail pair carrying this truck is shifted to align and couple with the fixed rail pair whereupon the truck is driven and transferred to a position on the fixed rails below the desired room and elevated thereinto. Accordingly, a plurality of trucks can optionally be shunted on a line of fixed rails without unloading the respective radiation sources. (Ohno, Y.)

Association between light absorption measurements of PM2.5 and distance from heavy traffic roads in the Mexico City metropolitan area.

Science.gov (United States)

Cortez-Lugo, Marlene; Escamilla-Núñez, Consuelo; Barraza-Villarreal, Albino; Texcalac-Sangrador, José Luis; Chow, Judith; Watson, John; Hernández-Cadena, Leticia; Romieu, Isabelle

2013-04-01

To study the relationship between light absorption measurements of PM2.5 at various distances from heavy traffic roads and diesel vehicle counts in Mexico City. PM2.5 samples were obtained from June 2003-June 2005 in three MCMA regions. Light absorption (b abs) in a subset of PM2.5 samples was determined. We evaluated the effect of distance and diesel vehicle counts to heavy traffic roads on PM2.5 b abs using generalized estimating equation models. Median PM2.5 b abs measurements significantly decrease as distance from heavy traffic roads increases (proads. Our model predicts that PM2.5 b abs measurements would increase by 20% (CI95% 3-38) as the hourly heavy diesel vehicle count increases by 150 per hour. PM2.5 b abs measurements are significantly associated with distance from motorways and traffic density and therefore can be used to assess human exposure to traffic-related emissions.

Vale nails down reduction of diesel particulate

Energy Technology Data Exchange (ETDEWEB)

Larmour, A.

2010-09-01

This article discussed innovations for reducing emissions of diesel particulate matter (DPM) from light-duty underground vehicles. DPM is a byproduct of diesel-powered equipment. Controlling these emissions at the source of generation is necessary for a healthy work environment and more cost effective than fresh air ventilation to reduce contaminant concentrations. Previous diesel particulate filter (DPF) systems required extensive human intervention, but this was deemed too inefficient. A DPF system that does not require human intervention was developed and proved successful in filter regeneration, longevity, and reliability. This DPF system uses a sintered metal filter element, a base metal, fuel-borne catalyst with an on-board dosing system, an electric heater that uses on-board power, and a sensor-based control unit. Software in the control unit adjusts fuel dosing rates and heater timing to ensure filter regeneration for different engines and operating scenarios. The new filter system is robust, and it has a compact design and long service-intervals. The product is still being tested to determine the costs and service life of the filter. More testing on fuel additives was deemed to be warranted, as was designing filter elements for larger engines used in heavy-duty vehicles.

Trusted Truck(R) II (phase A).

Science.gov (United States)

2009-01-01

The Trusted Truck Program was initiated in 2003 as a joint effort by NTRCI, Volvo and UT. The vision of the Trusted Truck program is to develop a secure and "trusted" transport solution from pickup to delivery. The program's objective is to incre...

Role of sensory and cognitive conspicuity in the prevention of collisions between motorcycles and trucks at T-intersections.

Science.gov (United States)

Law, Teik Hua; Ghanbari, Mahshid; Hamid, Hussain; Abdul-Halin, Alfian; Ng, Choy Peng

2016-11-01

Motorcyclists are particularly vulnerable to injury in crashes with heavy vehicles due to substantial differences in vehicle mass, the degree of protection and speed. There is a considerable difference in height between motorcycles and trucks; motorcycles are viewed by truck drivers from downward angles, and shorter distances between them mean steeper downward angles. Hence, we anticipated that the effects of motorcycle conspicuity treatments would be different for truck drivers. Therefore, this study aims to evaluate the effects of motorcycle conspicuity treatments on the identification and detection of motorcycles by truck drivers. Two complementary experiments were performed; the first experiment assessed the impact of motorcycle sensory conspicuity on the ability of un-alerted truck drivers to detect motorcycles, and the second experiment assessed the motorcycle cognitive conspicuity to alerted truck drivers. The sensory conspicuity was measured in terms of motorcycle detection rates by un-alerted truck drivers when they were not anticipating a motorcycle within a realistic driving scene, while the cognitive conspicuity was determined by the time taken by alerted truck drivers to actively search for a motorcycle. In the first experiment, the participants were presented with 10 pictures and were instructed to report the kinds of vehicles that were presented in the pictures. Each picture was shown to the participants for 600ms. In the second experiment, the participants were presented with the same set of pictures and were instructed to respond by clicking the right button on a mouse as soon as they detected a motorcycle in the picture. The results indicate that the motorcycle detection rate increases, and the response time to search for a motorcycle decreases, as the distance between the targeted motorcycle and the viewer decreases. This is true regardless of the type of conspicuity treatment used. The use of daytime running headlights (DRH) was found to

OHVT Technology Roadmap

Energy Technology Data Exchange (ETDEWEB)

Bradley, R.A.

2001-10-22

The U.S. Department of Energy (DOE) Office of Heavy Vehicle Technologies (OHVT) was created in March 1996 to address the public-interest transportation-energy aspects of a set of customers who at that time had been largely unrecognized, namely, the manufacturers, suppliers, and users of heavy transport vehicles (trucks, buses, rail, and inland marine). Previously, the DOE had focused its attention on meeting the needs of the personal-transport-vehicle customer (automobile manufacturers, suppliers, and users). Those of us who were of driving age at the time of the 1973 oil embargo and the 1979 oil price escalation vividly recall the inconvenience and irritation of having to wait in long lines for gasoline to fuel our cars. However, most of us, other than professional truck owners or drivers, were unaware of the impacts that these disruptions in the fuel supply had on those whose livelihoods depend upon the transport of goods. Recognizing the importance of heavy vehicles to the national economic health, the DOE created OHVT with a mission to conduct, in collaboration with its industry partners and their suppliers, a customer-focused national program to research and develop technologies that will enable trucks and other heavy vehicles to be more energy-efficient and able to use alternative fuels while reducing emissions. The Office of Heavy Vehicle Technologies convened a workshop in April 1996 to elicit input from DOE's heavy vehicle industry customers, including truck and bus manufacturers, diesel-engine manufacturers, fuel producers, suppliers to these industries, and the trucking industry. The preparation of a ''technology roadmap'' was one of the key recommendations by this customer group. Therefore, the OHVT Technology Roadmap* was developed in 1996 as a first step in crafting a common vision for a government research and development (R and D) partnership in this increasingly important transportation sector. The approach used in

Analysis the effect of advanced injection strategies on engine performance and pollutant emissions in a heavy duty DI-diesel engine by CFD modeling

International Nuclear Information System (INIS)

Mobasheri, Raouf; Peng, Zhijun; Mirsalim, Seyed Mostafa

2012-01-01

Highlights: ► Explore the effects of advanced multiple injection strategies in a DI-diesel engine. ► Achieving good agreement between the predicted results and experimental values. ► Analyzing three factors for optimization including pilot, main and post-injection. ► Injecting adequate fuel in each pulse accompanied with an appropriate EGR rate. ► Beneficial effects for significant soot reduction without a NOx penalty rate. - Abstract: An Advanced CFD simulation has been carried out in order to explore the combined effects of pilot-, post- and multiple-fuel injection strategies and EGR on engine performance and emission formation in a heavy duty DI-diesel engine. An improved version of the ECFM-3Z combustion model has been applied coupled with advanced models for NOx and soot formation. The model was validated with experimental data achieved from a Caterpillar 3401 DI diesel engine and good agreement between predicted and measured in-cylinder pressure, heat release rate, NOx and soot emissions was obtained. The optimizations were conducted separately for different split injection cases without pilot injection and then, for various multiple injection cases. Totally, three factors were considered for the injection optimization, which included EGR rate, the separation between main injection and post-injection and the amount of injected fuel in each pulse. For the multiple injection cases, two more factors (including double and triple injections during main injection) were also added. Results show that using pilot injection accompanied with an optimized main injection has a significant beneficial effect on combustion process so that it could form a separate 2nd stage of heat release which could reduce the maximum combustion temperature, which leads to the reduction of the NOx formation. In addition, it has found that injecting adequate fuel in post-injection at an appropriate EGR allows significant soot reduction without a NOx penalty rate.