A study of Cirus heavy water system isotopic purity

International Nuclear Information System (INIS)

Thomas, Shibu; Sahu, A.K.; Unni, V.K.P.; Pant, R.C.

2000-01-01

Cirus uses heavy water as moderator and helium as cover gas. Approximately one tonne of heavy water was added to the system every year for routine make up. Isotopic purity (IP) of this water used for addition was always higher than that of the system. Though this should increase IP of heavy water in the system, it has remained almost at the same level, over the years. A study was carried out to estimate the extent of improvement in IP of heavy water in the system that should have occurred because of this and other factors in last 30 years. Reasons for non-occurrence of such an improvement were explored. Ion exchange resins used for purification of heavy water and air ingress into helium cover gas system appear to be the principal sources of entry of light water into heavy water system. (author)

Analysis and application of heavy isotopes in the environment

Science.gov (United States)

Steier, Peter; Dellinger, Franz; Forstner, Oliver; Golser, Robin; Knie, Klaus; Kutschera, Walter; Priller, Alfred; Quinto, Francesca; Srncik, Michaela; Terrasi, Filippo; Vockenhuber, Christof; Wallner, Anton; Wallner, Gabriele; Wild, Eva Maria

2010-04-01

A growing number of AMS laboratories are pursuing applications of actinides. We discuss the basic requirements of the AMS technique of heavy (i.e., above ˜150 amu) isotopes, present the setup at the Vienna Environmental Research Accelerator (VERA) which is especially well suited for the isotope 236U, and give a comparison with other AMS facilities. Special emphasis will be put on elaborating the effective detection limits for environmental samples with respect to other mass spectrometric methods. At VERA, we have carried out measurements for radiation protection and environmental monitoring ( 236U, 239,240,241,242,244Pu), astrophysics ( 182Hf, 236U, 244Pu, 247Cm), nuclear physics, and a search for long-lived super-heavy elements ( Z > 100). We are pursuing the environmental distribution of 236U, as a basis for geological applications of natural 236U.

Analysis and application of heavy isotopes in the environment

International Nuclear Information System (INIS)

Steier, Peter; Dellinger, Franz; Forstner, Oliver; Golser, Robin; Knie, Klaus; Kutschera, Walter; Priller, Alfred; Quinto, Francesca; Srncik, Michaela; Terrasi, Filippo; Vockenhuber, Christof; Wallner, Anton; Wallner, Gabriele; Wild, Eva Maria

2010-01-01

A growing number of AMS laboratories are pursuing applications of actinides. We discuss the basic requirements of the AMS technique of heavy (i.e., above ∼150 amu) isotopes, present the setup at the Vienna Environmental Research Accelerator (VERA) which is especially well suited for the isotope 236 U, and give a comparison with other AMS facilities. Special emphasis will be put on elaborating the effective detection limits for environmental samples with respect to other mass spectrometric methods. At VERA, we have carried out measurements for radiation protection and environmental monitoring ( 236 U, 239,240,241,242,244 Pu), astrophysics ( 182 Hf, 236 U, 244 Pu, 247 Cm), nuclear physics, and a search for long-lived super-heavy elements (Z > 100). We are pursuing the environmental distribution of 236 U, as a basis for geological applications of natural 236 U.

161Dy Moessbauer spectroscopy of the intermetallic compounds DyNi2Si2, DyNi2Ge2 and DyAg2Si2

International Nuclear Information System (INIS)

Onodera, Hideya; Murata, Akifumi; Koizuka, Masaaki; Ohashi, Masayoshi; Yamaguchi, Yasuo

1994-01-01

161 Dy Moessbauer spectroscopic study has been performed on DyNi 2 Si 2 , DyNi 2 Ge 2 and DyAg 2 Si 2 in order to clarify microscopic properties of antiferromagnets with incommensurate and sinusoidally moment-modulated structure. The experiments were done using the standard 161 Tb Moessbauer sources prepared by neutron irradiation at the Japan Material Testing Reactor. The Moessbauer spectra of DyNi 2 Si 2 are analyzed satisfactorily by a single set of hyperfine parameters, and hence the sinusoidal moment-modulation is considered to be realized through a distribution of spin relaxation rate. The broadened spectra of DyNi 2 Ge 2 are fitted tentatively by three subspectra. It seems for DyNi 2 Ge 2 that the incommensurate arrangement of Dy moments differed in magnitude as well as the distribution of spin relaxation rate originates the moment modulation. The fact that the spectrum of DyAg 2 Si 2 at 3 K consists of two distinct subspectra ensures the complicated antiferromagnetic structure where two kinds of Dy moments differed in magnitude are arranged noncollinearly. (author)

Surface-ionization ion source designed for in-beam operation with the BEMS-2 isotope separator

International Nuclear Information System (INIS)

Bogdanov, D.D.; Voboril, J.; Demyanov, A.V.; Karnaukhov, V.A.; Petrov, L.A.

1976-01-01

A surface-ionization ion source designed to operate in combination with the BEMS-2 isotope separator in a heavy ion beam is described. The ion source is adjusted for the separation of rare-earth elements. The separation efficiency for 150 Dy is determined to be equal to about 20% at the ionizer temperature of 2600 deg K. The hold-up times for praseodymium, promethium and dysprosium in the ion source range from 5 to 10 sec at the ionizer temperature of 2500-2700 deg K

Heavy element stable isotope ratios. Analytical approaches and applications

International Nuclear Information System (INIS)

Tanimizu, Masaharu; Sohrin, Yoshiki; Hirata, Takafumi

2013-01-01

Continuous developments in inorganic mass spectrometry techniques, including a combination of an inductively coupled plasma ion source and a magnetic sector-based mass spectrometer equipped with a multiple-collector array, have revolutionized the precision of isotope ratio measurements, and applications of inorganic mass spectrometry for biochemistry, geochemistry, and marine chemistry are beginning to appear on the horizon. Series of pioneering studies have revealed that natural stable isotope fractionations of many elements heavier than S (e.g., Fe, Cu, Zn, Sr, Ce, Nd, Mo, Cd, W, Tl, and U) are common on Earth, and it had been widely recognized that most physicochemical reactions or biochemical processes induce mass-dependent isotope fractionation. The variations in isotope ratios of the heavy elements can provide new insights into past and present biochemical and geochemical processes. To achieve this, the analytical community is actively solving problems such as spectral interference, mass discrimination drift, chemical separation and purification, and reduction of the contamination of analytes. This article describes data calibration and standardization protocols to allow interlaboratory comparisons or to maintain traceability of data, and basic principles of isotope fractionation in nature, together with high-selectivity and high-yield chemical separation and purification techniques for stable isotope studies.

A new feature in the internal heavy isotope distribution in ozone

International Nuclear Information System (INIS)

Bhattacharya, S. K.; Liang, Mao-Chang; Savarino, Joel; Michalski, G.

2014-01-01

Ozone produced by discharge or photolysis of oxygen has unusually heavy isotopic composition ( 18 O/ 16 O and 17 O/ 16 O ratio) which does not follow normal mass fractionation rule: δ 17 O ∼ 0.52 * δ 18 O, expressed as an anomaly Δ 17 O = δ 17 O − 0.52 * δ 18 O. Ozone molecule being an open isosceles triangle can have the heavy isotope located either in its apex or symmetric (s) position or the base or asymmetric (as) position. Correspondingly, one can define positional isotopic enrichment, written as δ 18 O (s) or δ 18 O (as) (and similarly for δ 17 O) as well as position dependent isotope anomaly Δ 17 O (s) and Δ 17 O (as). Marcus and co-workers have proposed a semi-empirical model based in principle on the RRKM model of uni-molecular dissociation but with slight modification (departure from statistical randomness assumption for symmetrical molecules) which explains many features of ozone isotopic enrichment. This model predicts that the bulk isotope anomaly is contained wholly in the asymmetric position and the Δ 17 O (s) is zero. Consequently, Δ 17 O (as) = 1.5 * Δ 17 O (bulk) (named here simply as the “1.5 rule”) which has been experimentally confirmed over a range of isotopic enrichment. We now show that a critical re-analysis of the earlier experimental data demonstrates a small but significant departure from this 1.5 rule at the highest and lowest levels of enrichments. This departure provides the first experimental proof that the dynamics of ozone formation differs from a statistical model constrained only by restriction of symmetry. We speculate over some possible causes for the departure

A new feature in the internal heavy isotope distribution in ozone

Science.gov (United States)

Bhattacharya, S. K.; Savarino, Joel; Michalski, G.; Liang, Mao-Chang

2014-10-01

Ozone produced by discharge or photolysis of oxygen has unusually heavy isotopic composition (18O/16O and 17O/16O ratio) which does not follow normal mass fractionation rule: δ17O ˜ 0.52*δ18O, expressed as an anomaly Δ17O = δ17O - 0.52*δ18O. Ozone molecule being an open isosceles triangle can have the heavy isotope located either in its apex or symmetric (s) position or the base or asymmetric (as) position. Correspondingly, one can define positional isotopic enrichment, written as δ18O (s) or δ18O (as) (and similarly for δ17O) as well as position dependent isotope anomaly Δ17O (s) and Δ17O (as). Marcus and co-workers have proposed a semi-empirical model based in principle on the RRKM model of uni-molecular dissociation but with slight modification (departure from statistical randomness assumption for symmetrical molecules) which explains many features of ozone isotopic enrichment. This model predicts that the bulk isotope anomaly is contained wholly in the asymmetric position and the Δ17O (s) is zero. Consequently, Δ17O (as) = 1.5 * Δ17O (bulk) (named here simply as the "1.5 rule") which has been experimentally confirmed over a range of isotopic enrichment. We now show that a critical re-analysis of the earlier experimental data demonstrates a small but significant departure from this 1.5 rule at the highest and lowest levels of enrichments. This departure provides the first experimental proof that the dynamics of ozone formation differs from a statistical model constrained only by restriction of symmetry. We speculate over some possible causes for the departure.

Molybdenum isotope variations in calc-alkaline lavas from the Banda arc, Indonesia: Assessing the effect of crystal fractionation in creating isotopically heavy continental crust

NARCIS (Netherlands)

Wille, Martin; Nebel, Oliver; Pettke, Thomas; Vroon, Pieter Z.; König, Stephan; Schoenberg, Ronny

2018-01-01

Recent studies report a large Mo isotope variability of up to 1‰ (expressed in δ98/95MoNIST3134) in convergent margin lavas. These isotopic variations have been associated with subduction zone processes and ultimately may account for heavy and variable isotope signatures in evolved continental

Application of zinc isotope tracer technology in tracing soil heavy metal pollution

Science.gov (United States)

Norbu, Namkha; Wang, Shuguang; Xu, Yan; Yang, Jianqiang; Liu, Qiang

2017-08-01

Recent years the soil heavy metal pollution has become increasingly serious, especially the zinc pollution. Due to the complexity of this problem, in order to prevent and treat the soil pollution, it's crucial to accurately and quickly find out the pollution sources and control them. With the development of stable isotope tracer technology, it's able to determine the composition of zinc isotope. Based on the theory of zinc isotope tracer technique, and by means of doing some latest domestic and overseas literature research about the zinc isotope multi-receiving cups of inductively coupled plasma mass spectrometer (MC-ICP-MS) testing technology, this paper summarized the latest research results about the pollution tracer of zinc isotope, and according to the deficiencies and existing problems of previous research, made outlooks of zinc isotope fractionation mechanism, repository establishment and tracer multiple solutions.

Improvements on heavy water separation technology by isotopic water-hydrogen sulfide exchange

International Nuclear Information System (INIS)

Peculea, M.

1987-01-01

A series of possible variance is presented for the heavy water separation technology by isotopic H 2 O-H 2 S exchange at dual temperatures. The critical study of these variants, which are considered as characteristic quantities for the isotopes transport (production) and the extraction level is related to a dual temperature plant fed by liquid and cold column, which is the up-to-date technology employed in all heavy water production plants as variants of following plants are studied: dual temperature plant with double feeding; dual-temperature plant with equilibrium column (booster); dual-temperature-dual-pressure plant. Attention is paid to the variant with equilibration column (booster), executed and tested at the State Committee for Nuclear Energy and to the dual-temperature-dual pressure plant which presents the highest efficiency. (author)

Performance of refractometry in quantitative estimation of isotopic concentration of heavy water in nuclear reactor

International Nuclear Information System (INIS)

Dhole, K.; Roy, M.; Ghosh, S.; Datta, A.; Tripathy, M.K.; Bose, H.

2013-01-01

Highlights: ► Rapid analysis of heavy water samples, with precise temperature control. ► Entire composition range covered. ► Both variations in mole and wt.% of D 2 O in the heavy water sample studied. ► Standard error of calibration and prediction were estimated. - Abstract: The method of refractometry has been investigated for the quantitative estimation of isotopic concentration of heavy water (D 2 O) in a simulated water sample. Feasibility of refractometry as an excellent analytical technique for rapid and non-invasive determination of D 2 O concentration in water samples has been amply demonstrated. Temperature of the samples has been precisely controlled to eliminate the effect of temperature fluctuation on refractive index measurement. The method is found to exhibit a reasonable analytical response to its calibration performance over the purity range of 0–100% D 2 O. An accuracy of below ±1% in the measurement of isotopic purity of heavy water for the entire range could be achieved

Selected bibliography on heavy water, tritiated water and hydrogen isotopes (1981-1992)

International Nuclear Information System (INIS)

Gopalakrishnan, V.T.; Sutawane, U.B.; Rathi, B.N.

1994-01-01

A selected bibliography on heavy water, tritiated water and hydrogen isotopes is presented. This bibliography covers the period 1981-1992 and is in continuation to Division's earlier report BARC-1192 (1983). The sources of information for this compilation are Chemical Abstracts, INIS Atom Index and also some scattered search through journals and reports available in our library. No claim is made towards exhaustiveness of this bibliography even though sincere attempts have been made for a wide coverage. The bibliography is arranged under the headings: (1) production, purification, recovery, reprocessing and storage, (2) isotope exchange, 3) isotope analysis, (4) properties and (5) miscellaneous. Total number of references in the bibliography are 1762. (author)

Molecular assembly and magnetic dynamics of two novel Dy6 and Dy8 aggregates.

Science.gov (United States)

Guo, Yun-Nan; Chen, Xiao-Hua; Xue, Shufang; Tang, Jinkui

2012-04-02

Complexation of dysprosium(III) with the heterodonor chelating ligand o-vanillin picolinoylhydrazone (H(2)ovph) in the presence of a carbonato ligand affords two novel Dy(6) and Dy(8) clusters, namely, [Dy(6)(ovph)(4)(Hpvph)(2)Cl(4)(H(2)O)(2)(CO(3))(2)]·CH(3)OH·H(2)O·CH(3)CN (2) and [Dy(8)(ovph)(8)(CO(3))(4)(H(2)O)(8)]·12CH(3)CN·6H(2)O (3). Compound 2 is composed of three petals of the Dy(2) units linked by two carbonato ligands, forming a triangular prism arrangement, while compound 3 possesses an octanuclear core with an unprecedented tub conformation, in which Dy(ovph) fragments are attached to the sides of the carbonato core. The static and dynamic magnetic properties are reported and discussed. In the Dy(6) aggregate, three Dy(2) "skeletons", having been well preserved (see the scheme), contribute to the single-molecule-magnet behavior with a relatively slow tunneling rate, while the Dy(8) cluster only exhibits a rather small relaxation barrier.

Magnetic moments of high spin rotational states in 158Dy and 164Dy+

International Nuclear Information System (INIS)

Seiler-Clark, G.

1983-09-01

For the study of their magnetic moments yrast states in 158 Dy and 164 Dy were excited via the multiple-Coulomb excitation by a 4.7 MeV/u 208 Pb beam. Hereby especially the question was of interest, how the one-particle effects in the nuclear structure in the region of the backbending anomaly in 158 Dy take effects on the g-factors of the high spin states in this region. The particle-γ angular correlations perturbed in the transient magnetic field during the passing of the excited Dy ions through a thin magnetized iron foil were measured. By the selective position-sensitive detection of Dy recoil ions and Pb projectiles under forward angles it was possible to determine additionally to the g-factors in the backbending region also g-factors in the spin region I 158 Dy and 164 Dy by detection of the particle-γ correlations precessing in the static hyperfine field after implantation in iron. The static hyperfine field was at the 4 + state in 164 Dy determined to B (Dy,Fe) = 245+-25 T. The g-factors were determined by comparison of the experimental results with calculations of the perturbed angular correlations by time-differential regarding of the population and de-excitation of the yrast states as well as by precession and hyperfine-relaxation effects during the flight of the Dy ions in the vacuum. (orig./HSI) [de

Early History of Heavy Isotope Research at Berkeley

Energy Technology Data Exchange (ETDEWEB)

Glenn T. Seaborg

1976-06-01

I have had the idea for some time that it would be interesting and worthwhile to put together an account of the early work on heavy isotopes at Berkeley. Of a special interest is the discovery of plutonium (atomic number 94) and the isotope U{sup 233}, and the demonstration of their fission with slow neutrons. This work served as a prelude to the subsequent Plutonium Project (Metallurgical Project) centered at the University of Chicago, in connection with which I have also had the idea of putting together a history of the work of my chemistry group. I have decided that it would be an interesting challenge to write this account on a day-to-day basis in a style that would be consistent with the entries having been written at the end of each day. The aim would be to make this history as accurate as possible by going back to the original records and using them with meticulous care.

Heterogeneous bilayer films NiFe (Fe)-Dy: magnetic circular dichroism and Dy spin ordering

Energy Technology Data Exchange (ETDEWEB)

Markov, V.V. E-mail: ise@iph.krasn.ruise@iph.krasnoyarsk.su; Kesler, V.G.; Khudyakov, A.E.; Edelman, I.S.; Bondarenko, G.V

2001-08-01

Results of the magnetic circular dichroism (MCD) and Auger electron spectroscopy (AES) investigations in the 3d transition metal-Dy bi-layer films are presented. It is shown that even at room temperature the Dy layer makes a contribution to MCD of the bi-layer film, which corresponds to the MCD value in the single-layer Dy film measured below T{sub C}=85 K. According to the AES data there is no sharp interface between 3d and Dy layers in these films. Some amount of Ni and Fe atoms is dispersed in the Dy layer and some amount of Dy atoms is dispersed in the 3d layer. The comparison of the MCD and AES data allows one to suppose the Dy layer in the bi-layer films to be magnetically ordered at room temperature under the influence of the 3d-layer spin system. The influence spreads to long distances inside Dy layer through the 3d-ions dispersed in it.

Heterogeneous bilayer films NiFe (Fe)-Dy: magnetic circular dichroism and Dy spin ordering

International Nuclear Information System (INIS)

Markov, V.V.; Kesler, V.G.; Khudyakov, A.E.; Edelman, I.S.; Bondarenko, G.V.

2001-01-01

Results of the magnetic circular dichroism (MCD) and Auger electron spectroscopy (AES) investigations in the 3d transition metal-Dy bi-layer films are presented. It is shown that even at room temperature the Dy layer makes a contribution to MCD of the bi-layer film, which corresponds to the MCD value in the single-layer Dy film measured below T C =85 K. According to the AES data there is no sharp interface between 3d and Dy layers in these films. Some amount of Ni and Fe atoms is dispersed in the Dy layer and some amount of Dy atoms is dispersed in the 3d layer. The comparison of the MCD and AES data allows one to suppose the Dy layer in the bi-layer films to be magnetically ordered at room temperature under the influence of the 3d-layer spin system. The influence spreads to long distances inside Dy layer through the 3d-ions dispersed in it

High resolution conductometry for isotopic assay of deuterium in mixtures of heavy water and light water

International Nuclear Information System (INIS)

Ananthanarayanan, R.; Sahoo, P.; Murali, N.

2014-01-01

A PC based high resolution conductivity monitoring technique has been deployed for determination of isotopic purity of heavy water in samples containing heavy water and light water mixtures using pulsating sensor based conductivity monitoring instrument. The technique involves accurate determination of conductivities of a series of specially treated heavy water and light water mixtures of various compositions at a constant solution temperature. The shift in conductivity (Δκ), which is the difference between conductivities of composite mixture after and before the formation of a typical complex compound (boric acid–mannitol complex in this case), shows a smooth and reproducible decreasing trend with increase in percentage composition of heavy water. This relation, which is obtained by appropriate calibration, is used in the software program for direct display of isotopic purity of heavy water. The technique is examined for determination of percentage composition of heavy water in the entire range of concentration (0-100 %) with reasonable precision (relative standard deviation, RSD ≤1.5 %). About 1 mL of sample is required for each analysis and analysis is completed within a couple of minutes after pretreatment of sample. The accuracy in measurement is ≤1.75 %. (author)

Structure and luminescence properties of Dy2O3 doped bismuth-borate glasses

International Nuclear Information System (INIS)

Mugoni, Consuelo; Gatto, C.; Pla-Dalmau, A.; Siligardi, C.

2017-01-01

In this study heavy bismuth-borate glasses were studied as host matrices of Dy 2 O 3 rare earth, for potential application as scintillator materials in high energy physics experiments and in general radiation detection systems. Glass matrices were prepared from 20BaO-xBi 2 O 3 -(80-x)B 2 O 3 (x = 20, 30, 40 mol%) ternary systems and synthesized by the melt-quenching method at different temperatures in order to obtain high density and high transparency in the UV/Vis range. Particularly, the glass manifesting the higher transparency and with sufficiently high density was doped with Dy 2 O 3 (2.5 and 5 mol%) in order to induce the luminescence characteristics. The effects of Bi 2 O 3 and Dy 2 O 3 on density, thermal behaviour, transmission as well as luminescence properties under UV excitation, were investigated. The experimental results show that the synthesized glasses can be considered promising candidate materials as dense scintillators, due to the Dy 3+ centres emission.

Recent search for quarks and very heavy hydrogen isotopes using an (almost) all-electrostatic system

International Nuclear Information System (INIS)

Schiffer, J.P.; Ernst, H.; Henning, W.; Kutschera, W.

1981-01-01

In order to search for +1/3e particles in metals we adapted the Argonne Dynamitron to accelerate particles from a metal filament. The particles, after being accelerated, were bent by an electrostatic deflector, passed through a foil which dissociated any molecules, and bent by a second electrostatic deflector to eliminate molecular fragments, through a slit system into a Si surface-barrier detector. Only charged particles that originated at the terminal of the accelerator and did not change their mass or charge state throughout, could reach the detector. The energy deposited in the detector was then a direct measure of the particle's charge: a +1/3e particle would have one third the energy of a single charged one. But all particles were accepted, independent of their mass. These experiments were performed with negative results. Recently we adapted this technique to a search for anomalously heavy isotopes of hydrogen. A limit on such particles would be useful on quite general grounds. In order to do the measurement, however, the technique had to be modified in several ways. 1) To eliminate the known isotopes of hydrogen a small magnetic field was introduced, sufficient to deflect the light isotopes onto a beam stop, but leaving very heavy isotopes essentially undeflected. 2) The solid state detector was replaced by a ΔE-E telescope, that provided charge identification, and 3) The two elements in the telescope were separated sufficiently to allow the time-of-flight measurements to be carried out, in order to search for heavy particles. 4) In addition, a nickel foil was placed in front of the detector of sufficient thickness to stop any normal ions (with Z greater than or equal to 2) but thin enough to readily transmit hydrogen-like particles of any mass. From preliminary tests we anticipate no problems in observing a heavy hydrogen isotope which is 10 -15 of the primary hydrogenic beam, and with minor improvements we might be able to reach 10 -17

Heavy metal pollution and Pb isotopic tracing in the intertidal surface sediments of Quanzhou Bay, southeast coast of China

International Nuclear Information System (INIS)

Yu, Ruilian; Zhang, Weifang; Hu, Gongren; Lin, Chengqi; Yang, Qiuli

2016-01-01

Concentrations of 16 heavy metals and Pb isotopic ratios in the intertidal surface sediments of Quanzhou Bay were determined to study the pollution level of heavy metals and the sources of Pb. The results showed that most concentrations of Cd, Sn, Mn, Cu, Zn, Cr, Pb, Hg, Ni, Co, Cs, Fe and V were higher than the background values, while most concentrations of Ti, Sb and Sr were lower than the background values. The mean concentrations of Cu, Zn, Pb, Cr and Cd exceeded the first-grade criteria of Chinese marine sediment quality. The geo-accumulation indexes revealed that the sediments had been polluted by some heavy metals. The results of Pb isotopic tracing indicated that the total Pb in the sediments were mainly from parent material, industrial emission and vehicle exhaust with the mean contributions of 38.2%, 51.3% and 10.5%, respectively, calculated by a three-end-member model of Pb isotopic ratios. - Highlights: •Level of 16 heavy metals in intertidal surface sediments of Quanzhou Bay was studied. •The sediments had been polluted by some heavy metals including Pb. •Pb isotopic compositions in the sediments and the potential sources were determined. •A three-end member model was applied to estimate the contributions of Pb sources. •Industrial emission was the major anthropogenic Pb contributor in the sediments.

Atomic masses of rare-earth isotopes

International Nuclear Information System (INIS)

Schmidt-Ott, W.D.; Kantus, R.; Runte, E.

1981-01-01

A survey is given of decay energies of rare-earth isotopes measured in electron-capture decay by relative Psub(K) ratios, ECsub(K)/β + , and EC/β + ratios. Atomic masses of A = 147 isotopes and of 146 Gd and 148 Dy were derived. The masses of these isotopes and of α-decaying precessors are compared with predictions of current mass formulae. The subshell closure at Z = 64 is shown for N = 82, and 84 isotones. (orig.)

Coercivity enhancements of Nd–Fe–B sintered magnets by diffusing DyHx along different axes

International Nuclear Information System (INIS)

Ma, Tianyu; Wang, Xuejiao; Liu, Xiaolian; Wu, Chen; Yan, Mi

2015-01-01

Diffusing heavy rare earth elements along the grain boundaries (GBs) for Nd 2 Fe 14 B-type sintered magnets serves as an effective method to enhance coercivity and to minimize remanence loss simultaneously. Considering the texture anisotropy of Nd-rich GB phases, the coercivity incremental difference by diffusing DyH x fine powders along or perpendicular to the  <0 0 1 >  easy axis (c-axis) has been investigated. The coercivity increases more rapidly to 20.61 kOe (5.76 kOe higher than that of the as-sintered state) when diffusing along the c-axis than that diffusing perpendicular to c-axis (18.85 kOe, 4.00 kOe higher than the as-sintered state). Microstructural investigation reveals that Dy diffuses more easily towards the magnet inner part when treating along the c-axis than that for the perpendicular case due to the anisotropic distribution of the Nd-rich phase. This is verified by a higher Dy content at equivalent diffusing depth and a much deeper final diffusion distance. The local Dy-containing fractions with a stronger anisotropy field are richer for the magnet treated along the c-axis, leading to the much rapider coercivity enhancement. This work reveals that diffusion heavy rare earth along the c-axis is more effective to enhance coercivity for aligned Nd–Fe–B sintered magnets. (paper)

Phosphors doped with Dy3+ and Gd3+ for lighting

International Nuclear Information System (INIS)

Su, Q; Pei, Z.; Zeng, Q.; Chi, L.

1998-01-01

Full text: Some heavy lanthanide ions with even atomic number such as Dy 3+ and Gd 3+ are abundant in the ion adsorption type deposit of China. Their price is cheap and they have specific spectroscopic properties which can be used as phosphors. Dy 3i on has two dominant bands in the emission spectrum. The yellow band (575 nm) corresponds to the hypersensitive transition 4 F 9/2 → 6 H 13/2 (ΔL=2, ΔJ=2), and the blue band (485 nm) corresponds to the 4 F 9/2 → 6 H 15/2 transition. Factors which influence on the yellow- to-blue intensity ratio (Y/B) were investigated. Adjusting to a suitable Y/B, Dy 3+ will emit white light with high colour temperature and can be used for lighting. But Dy 3+ ion has only narrow excitation bands of f-f transitions ranging from 300-500 nm, no broad excitation band such as charge transfer band or f-d transition band exists in the UV region 200-300 nm. Hence its luminescent efficiency is low when it is excited by UV radiation emitted from the mercury plasma. This is one of the drawbacks to its use as lamp phosphor. However, this can be overcome by sensitisation with Gd 3+ , Pb 2+ or other sensitisers such as vanadate shown in this report. Gd 3+ is not only a good matrix, but also a good sensitiser. Using its 8 S 7/2 → 6 D, 6 I and 6 P transitions, the UV excitation energy can be absorbed and transferred to the activator such as Dy 3+ . Therefore, in some cases Gd 3+ is better than Y 3+ which is optical inert as a matrix. For the phosphor Ca 1.96 Pb 0.04 RE 7.9 Dy 0.1 (SiO 4 ) 6 O 2 prepared by sol-gel method, the intensity of Dy 3+ in the Gd 3+ compound (RE=Gd 3+ ) is six times that in the Y 3+ compound. Some new phosphors doped with Dy 3+ and Gd 3+ prepared in our laboratory are reported

Inter-band B(E2) transitions strengths in 160-170Dy nuclei

International Nuclear Information System (INIS)

Vargas, Carlos E; Lerma, Sergio; Velázquez, Víctor

2015-01-01

The rare earth region of the nuclear landscape is characterized by a large collectivity observed. The microscopic studies are difficult to perform in the region due to the enormous size of the valence spaces. The use of symmetries based models avoids that problem, because the symmetry allows to choose the most relevant degrees of freedom for the system under consideration. We present theoretical results for electromagnetic properties in 160-168 Dy isotopes employing the pseudo-SU(3) model. In particular, we study the B(E2) inter-band transition strengths between the ground state, γ and, β-bands. The model succesfully describes in a systematic way rotational features in these nuclei and allows to extrapolate toward the midshell nucleus 170 Dy

ZIRCONIUM—HAFNIUM ISOTOPE EVIDENCE FROM METEORITES FOR THE DECOUPLED SYNTHESIS OF LIGHT AND HEAVY NEUTRON-RICH NUCLEI

Energy Technology Data Exchange (ETDEWEB)

Akram, W.; Schönbächler, M. [School of Earth, Atmospheric and Environmental Sciences, The University of Manchester, Oxford Road, Manchester, M13 9PL (United Kingdom); Sprung, P. [Institut für Planetologie, Universität Münster, Wilhelm-Klemm-Strasse 10, D-48149 Münster (Germany); Vogel, N. [Institute for Geochemistry and Petrology, ETH, Clausiusstrasse 25, 8092 Zürich (Switzerland)

2013-11-10

Recent work based on analyses of meteorite and terrestrial whole-rock samples showed that the r- and s- process isotopes of Hf were homogeneously distributed throughout the inner solar system. We report new Hf isotope data for Calcium-Aluminum-rich inclusions (CAIs) of the CV3 carbonaceous chondrite Allende, and novel high-precision Zr isotope data for these CAIs and three carbonaceous chondrites (CM, CO, CK). Our Zr data reveal enrichments in the neutron-rich isotope {sup 96}Zr (≤1ε in {sup 96}Zr/{sup 90}Zr) for bulk chondrites and CAIs (∼2ε). Potential isotope effects due to incomplete sample dissolution, galactic and cosmic ray spallation, and the nuclear field shift are assessed and excluded, leading to the conclusion that the {sup 96}Zr isotope variations are of nucleosynthetic origin. The {sup 96}Zr enrichments are coupled with {sup 50}Ti excesses suggesting that both nuclides were produced in the same astrophysical environment. The same CAIs also exhibit deficits in r-process Hf isotopes, which provides strong evidence for a decoupling between the nucleosynthetic processes that produce the light (A ≤ 130) and heavy (A > 130) neutron-rich isotopes. We propose that the light neutron-capture isotopes largely formed in Type II supernovae (SNeII) with higher mass progenitors than the supernovae that produced the heavy r-process isotopes. In the context of our model, the light isotopes (e.g. {sup 96}Zr) are predominantly synthesized via charged-particle reactions in a high entropy wind environment, in which Hf isotopes are not produced. Collectively, our data indicates that CAIs sampled an excess of materials produced in a normal mass (12-25 M{sub ☉}) SNII.

Isotopic shifts and configuration mixing in the dysprosium II spectrum

International Nuclear Information System (INIS)

Aufmuth, P.

1977-01-01

Using a photoelectric Fabry-Perot spectrometer with digital data acquisition, the isotopic shifts of all stable dysprosium isotopes (Z = 66, A = 156, 158, 160, 161, 162, 163, 164) have been measured in transitions from the groundstate configuration 4f 10 6s to the excited configurations 4f 9 5d6s, 4f 9 5d 2 , and 4f 10 6p of the spark spectrum. Mass and volume effects have been seperated; the results are compared with arc spectrum measurements. From the volume effect of a pure s-p transition the change of the mean electric quadratic nuclear radius delta 2 > has been calculated. In order to test fine structure calculations of the Dy II spectrum, the isotopic shifts of 29 lines of the isotopes 162 Dy and 164 Dy have been measured. Based on the sharing rule, the reported configuration mixing could be confirmed in principle; for one energy level (E = 22908 K) the asignement has been proved to be false, in the case of three other levels (E = 22467, 22672, and 28885 K) the asignement is doubtfull. For the ground state levels 4f 10 6s 6 I the influence of relativistic effects could be proved; these effects can be interpreted in the framework of a parametric representation of the isotopic shift. The order of magnitude of the crossed second order effects has been estimated. (orig.) [de

Anaerobic methane oxidation and a deep H2S sink generate isotopically heavy sulfides in Black Sea sediments

DEFF Research Database (Denmark)

Jørgensen, BB; Bottcher, ME; Luschen, H.

2004-01-01

to isotopically heavy pyrite in a sediment open to diffusion. These results have general implications for the marine sulfur cycle and for the interpretation of sulfur isotopic data in modern sediments and in sedimentary rocks throughout earth's history. Copyright (C) 2004 Elsevier Ltd...

Electrolytic separation factors for oxygen isotopes in light and heavy water solutions

International Nuclear Information System (INIS)

Gulens, J.; Olmstead, W.J.; Longhurst, T.H.; Gale, K.L.; Rolston, J.H.

1987-01-01

The electrolytic separation factor, α, has been measured for /sup 17/O and /sup 18/O at Pt and Ni anodes in both light and heavy water solutions of 6M KOH as a function of current density. For oxygen-17, isotopic separation effects were not observed, within the experimental uncertainty of +-2%, under all conditions studied. For oxygen-18, there is a small difference of 2% in α values between Pt and Ni in both light and heavy water solutions, but there is no significant difference in α values between light and heavy water solutions. In light waters solutions, the separation factor at Pt is small, α(/sup 18/O) ≤ 1.02 for i ≥ 0.1 A/cm/sub 2/. This value agrees reasonably well with theoretical estimates

Heavy metals pollution and pb isotopic signatures in surface sediments collected from Bohai Bay, North China.

Science.gov (United States)

Gao, Bo; Lu, Jin; Hao, Hong; Yin, Shuhua; Yu, Xiao; Wang, Qiwen; Sun, Ke

2014-01-01

To investigate the characteristics and potential sources of heavy metals pollution, surface sediments collected from Bohai Bay, North China, were analyzed for the selected metals (Cd, Cr, Cu, Ni, Pb, and Zn). The Geoaccumulation Index was used to assess the level of heavy metal pollution. Pb isotopic compositions in sediments were also measured to effectively identify the potential Pb sources. The results showed that the average concentrations of Cd, Cr, Cu, Ni, Pb, and Zn were 0.15, 79.73, 28.70, 36.56, 25.63, and 72.83 mg/kg, respectively. The mean concentrations of the studied metals were slightly higher than the background values. However, the heavy metals concentrations in surface sediments in Bohai Bay were below the other important bays or estuaries in China. The assessment by Geoaccumulation Index indicated that Cr, Zn, and Cd were classified as "the unpolluted" level, while Ni, Cu, and Pb were ranked as "unpolluted to moderately polluted" level. The order of pollution level of heavy metals was: Pb > Ni > Cu > Cr > Zn > Cd. The Pb isotopic ratios in surface sediments varied from 1.159 to 1.185 for (206)Pb/(207)Pb and from 2.456 to 2.482 for (208)Pb/(207)Pb. Compared with Pb isotopic radios in other sources, Pb contaminations in the surface sediments of Bohai Bay may be controlled by the mix process of coal combustion, aerosol particles deposition, and natural sources.

Magnetic dipole excitations of the 163Dy nucleus

Science.gov (United States)

Zenginerler, Zemine; Tabar, Emre; Yakut, Hakan; Kuliev, Ali Akbar; Guliyev, Ekber

2014-03-01

In this study some properties of the magnetic dipole excitations of the deformed odd mass 163Dy nucleus were studied by using Quasiparticle-phonon nuclear model (QPNM). The several of the ground-state and low-lying magnetic dipole (M1) mode characteristics were calculated for deformed odd-mass nuclei using a separable Hamiltonian within the QPNM. The M1 excited states, reduced transition probabilities B(M1), the ground-state magnetic properties such as magnetic moment (μ), intrinsic magnetic moment (gK) , effective spin factor (gseff.) are the fundamental characteristics of the odd-mass nucleus and provide key information to understand nuclear structure. The theoretical results were compared with the available experimental data and other theoretical approaches. Calculations show that the spin-spin interaction in this isotopes leads to polarization effect influencing the magnetic moments. Furthermore we found a strong fragmentation of the M1 strength in 163Dy nucleus which was in qualitative agreement with the experimental data. Sakarya University, Project Number: 2012-50-02-007 and Z.Zenginerler acknowledge to TUBITAK-TURKEY 2013, fellowship No: 2219.

Recent progress of hydrogen isotope behavior studies for neutron or heavy ion damaged W

International Nuclear Information System (INIS)

Oya, Yasuhisa; Hatano, Yuji; Shimada, Masashi; Buchenauer, Dean; Kolasinski, Robert; Merrill, Brad; Kondo, Sosuke; Hinoki, Tatsuya; Alimov, Vladimir Kh.

2016-01-01

Highlights: • This paper reviews recent results pertaining to hydrogen isotope behavior in neutron and heavy ion damaged W. • Accumulation of damage in W creates stable trapping sites for hydrogen isotopes, thereby changing the observed desorption behavior. • The distribution of defects throughout the sample also changes the shape of TDS spectrum. • Experimental results show that production of Re by nuclear reaction of W with neutrons reduces the density of trapping sites, though no remarkable retention enhancement is observed. - Abstract: This paper reviews recent results pertaining to hydrogen isotope behavior in neutron and heavy ion damaged W. Accumulation of damage in W creates stable trapping sites for hydrogen isotopes, thereby changing the observed desorption behavior. In particular, the desorption temperature shifts higher as the defect concentration increases. In addition, the distribution of defects throughout the sample also changes the shape of TDS spectrum. Even if low energy traps were distributed in the bulk region, the D diffusion toward the surface requires additional time for trapping/detrapping during surface-to-bulk transport, contributing to a shift of desorption peaks toward higher temperatures. It can be said that both of distribution of damage (e.g. hydrogen isotope trapping sites) and their stabilities would have a large impact on desorption. In addition, transmutation effects should be also considered for an actual fusion environment. Experimental results show that production of Re by nuclear reaction of W with neutrons reduces the density of trapping sites, though no remarkable retention enhancement is observed.

Recent progress of hydrogen isotope behavior studies for neutron or heavy ion damaged W

Energy Technology Data Exchange (ETDEWEB)

Oya, Yasuhisa, E-mail: syoya@ipc.shizuoka.ac.jp [Shizuoka University, 836 Ohya, Suruga-ku Shizuoka 422-8529 (Japan); Hatano, Yuji [University of Toyama, 3190 Gofuku, Toyama 939-8555 (Japan); Shimada, Masashi [Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Buchenauer, Dean; Kolasinski, Robert [Sandia National Laboratories, Livermore, CA 94551 (United States); Merrill, Brad [Idaho National Laboratory, Idaho Falls, ID 83415 (United States); Kondo, Sosuke; Hinoki, Tatsuya [Kyoto University, Gokasho, Uji 611-0011 (Japan); Alimov, Vladimir Kh. [University of Toyama, 3190 Gofuku, Toyama 939-8555 (Japan)

2016-12-15

Highlights: • This paper reviews recent results pertaining to hydrogen isotope behavior in neutron and heavy ion damaged W. • Accumulation of damage in W creates stable trapping sites for hydrogen isotopes, thereby changing the observed desorption behavior. • The distribution of defects throughout the sample also changes the shape of TDS spectrum. • Experimental results show that production of Re by nuclear reaction of W with neutrons reduces the density of trapping sites, though no remarkable retention enhancement is observed. - Abstract: This paper reviews recent results pertaining to hydrogen isotope behavior in neutron and heavy ion damaged W. Accumulation of damage in W creates stable trapping sites for hydrogen isotopes, thereby changing the observed desorption behavior. In particular, the desorption temperature shifts higher as the defect concentration increases. In addition, the distribution of defects throughout the sample also changes the shape of TDS spectrum. Even if low energy traps were distributed in the bulk region, the D diffusion toward the surface requires additional time for trapping/detrapping during surface-to-bulk transport, contributing to a shift of desorption peaks toward higher temperatures. It can be said that both of distribution of damage (e.g. hydrogen isotope trapping sites) and their stabilities would have a large impact on desorption. In addition, transmutation effects should be also considered for an actual fusion environment. Experimental results show that production of Re by nuclear reaction of W with neutrons reduces the density of trapping sites, though no remarkable retention enhancement is observed.

Coercivity enhancement of Nd–Fe–B sintered magnets with intergranular adding (Pr, Dy, Cu)−H{sub x} powders

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yujing; Ma, Tianyu, E-mail: maty@zju.edu.cn; Liu, Xiaolian; Liu, Pan; Jin, Jiaying; Zou, Junding; Yan, Mi, E-mail: mse_yanmi@zju.edu.cn

2016-02-01

Forming Nd{sub 2}Fe{sub 14}B/(Nd, Dy){sub 2}Fe{sub 14}B core–shell structure by intergranular adding Dy-containing sources into Nd–Fe–B sintered magnets is effective to improve coercivity and to minimize remanence loss simultaneously. However, the excessive Dy located in the intergranular regions has nearly no hard magnetic contribution, causing its low utilization efficiency. In this work, diluted Dy powders (Pr{sub 37}Dy{sub 30}Cu{sub 33})–H{sub x} were prepared and incorporated into Nd–Fe–B sintered magnets via a dual-alloy approach. The coercivity increases rapidly from 15.0 to 18.2 kOe by 21.3% with 2.0 wt% (Pr, Dy, Cu)–H{sub x} addition (the equivalent Dy is only 0.32 at%). The deduced coercivity incremental ratio is 10.0 kOe per unit Dy at%. Dehydrogenation reaction of (Pr, Dy, Cu)–H{sub x} occurs during sintering, which favors Dy diffusion towards the 2:14:1 phase grains as well as smoothing the grain boundaries (GBs). The enhanced local anisotropic field and the well decoupled 2:14:1 phase grains contribute to such rapid coercivity enhancement. This work suggests that adding diluted Dy hydrides is promising for fabricating high coercivity Nd–Fe–B sintered magnets with less heavy rare-earth consumption. - Highlights: • (Pr, Dy, Cu)–H{sub x} hydride powders were introduced into Nd–Fe–B sintered magnets. • Rapid coercivity enhancement from 15.0 kOe to 18.2 kOe with only 0.32 at% Dy was realized. • High utilization efficiency of Dy was achieved due to its promoted diffusion process. • Wettability and mobility of grain boundary phase was improved.

Effect of separated layer thickness on magnetoresistance and magnetic properties of Co/Dy/Co and Ni/Dy/Ni film systems

Science.gov (United States)

Shabelnyk, T. M.; Shutylieva, O. V.; Vorobiov, S. I.; Pazukha, I. M.; Chornous, A. M.

2018-01-01

Co(5 nm)/Dy(tDy)/Co(20 nm)/S and Ni(5 nm)/Dy(tDy)/Ni(20 nm)/S trilayer films are prepared by electron-beam sputtering to investigate the influence of dysprosium layer thickness (tDy) and thermal annealing on the crystal structure, magnetoresistance (MR) and magnetic properties of thin films. The thickness of Dy layer changed in the range from 1 nm to 20 nm. The samples annealed for 20 min at 700 K. Electron diffraction patterns reveal that the as-deposited and annealed systems Co/Dy/Co and Ni/Dy/Ni had fcc-Co + hcp-Dy and fcc-Ni + hcp-Dy phase state, respectively. It is also shown that at the tDy = 15 nm the transition from amorphous to crystalline structures of Dy layer is observed. An increase in the Dy layer thickness results in changes in the MR and magnetic properties of the trilayer systems. It is shown that MR is most thermally stable against annealing to 700 K at tDy = 15 nm for Co/Dy/Co as well as for Ni/Dy/Ni. For tDy = 15 nm the, value of MR for both system increases by two times compared to those of pure ferromagnetic (FM) samples. The coercivity (Bc), remanent (Mr) and saturation (Ms) magnetization of the in-plain magnetization hysteresis loops are related to the Dy layer thickness too. The coercivity depends on the FM materials type and diffusion processes at the layer boundary. Accordingly, Mr and Ms are reduced with tDy increasing before and after annealing for both trilayer systems.

Separation and recovery of high grade Dy2O3 by solvent extraction process with DEHPA in kerosene

International Nuclear Information System (INIS)

Mishra, S.L.; Thakur, N.V.; Koppiker, K.S.

1993-01-01

During the solvent extraction (SX) fractionation of rare earths chloride obtained from monazite, a heavy RE (HRE) fraction assaying 60% Y 2 O 3 is produced. This is purified further to 93% Y 2 O 3 by another SX cycle. During this step most of Dy and Tb get separated to yield a concentrate assaying >50% Dy 2 O 3 . An attempt has been made to process this Dy rich concentrate to obtain a high grade Dy 2 O 3 by a SX route using DEHPA in kerosene. The distribution data (D vs H i + ) of Dy have been generated experimentally at various metal concentrations and similar data for other metals present (Gd, Tb, Y, Er and Ho) have been derived using a mathematical expression developed in our laboratory. Based on this information mathematical models for extraction behaviour of these HRE have been derived and used in a computer program developed for multicomponent system. This program has been utilised to optimise the process parameters to obtain 95-97% pure Dy 2 O 3 at about 90% recovery. The parameters have been experimentally confirmed and Dy 2 O 3 95.5% pure w.r.t. Tb was obtained at about 90% recovery, thus confirming the validity of the program. This paper presents data obtained during these investigations. (author). 6 refs., 5 tabs

Production and identification of heavy Ni isotopes: Evidence for the doubly magic nucleus 7828Ni. Short note

International Nuclear Information System (INIS)

Engelmann, C.; Ameil, F.; Bernas, M.; Heinz, A.; Janas, Z.; Kozhuharov, C.; Miehe, C.; Pfuetzner, M.; Roehl, C.; Stephan, C.; Tassan-Got, L.; Voss, B.

1995-07-01

We report the first observation of the doubly magic nucleus 78 Ni 50 and the heavy isotopes 77 Ni, 73,74,75 Co, 80 Cu. The isotopes were produced by nuclear fission in collisions of 750 A.MeV projectiles of 238 U on Be target nuclei. The fully-stripped fission products were separated in-flight by the fragment separator FRS and identified event-by-event by measuring the magnetic rigidity, the trajectory, the energy deposit, and the time of flight. Production cross-sections and fission yields for the new Ni-isotopes are given. (orig.)

Effect of swift heavy ion irradiation on surface resistance of DyBa 2

Indian Academy of Sciences (India)

We report the observation of a pronounced peak in surface resistance at microwave frequencies of 4.88 GHz and 9.55 GHz and its disappearance after irradiation with swift ions in laser ablated DyBa2Cu3O7- (DBCO) thin films. The measurements were carried out in zero field as well as in the presence of magnetic fields ...

Using stable lead isotopes to trace heavy metal contamination sources in sediments of Xiangjiang and Lishui Rivers in China.

Science.gov (United States)

Sun, Guo-Xin; Wang, Xin-Jun; Hu, Qin-Hong

2011-12-01

Lead isotopes and heavy metal concentrations were measured in two sediment cores sampled in estuaries of Xiangjiang and Lishui Rivers in Hunan province, China. The presence of anthropogenic contribution was observed in both sediments, especially in Xiangjiang sediment. In the Xiangjiang sediment, the lower (206)Pb/(207)Pb and higher (208)Pb/(206)Pb ratio, than natural Pb isotope signature (1.198 and 2.075 for (206)Pb/(207)Pb and (208)Pb/(206)Pb, respectively), indicated a significant input of non-indigenous Pb with low (206)Pb/(207)Pb and high (208)Pb/(206)Pb. The corresponding concentrations of heavy metals (As, Cd, Zn, Mn and Pb) were much higher than natural values, suggesting the contaminations of heavy metals from extensive ore-mining activities in the region. Copyright © 2011 Elsevier Ltd. All rights reserved.

Influence of Dy in solid solution on the degradation behavior of binary Mg-Dy alloys in cell culture medium.

Science.gov (United States)

Yang, Lei; Ma, Liangong; Huang, Yuanding; Feyerabend, Frank; Blawert, Carsten; Höche, Daniel; Willumeit-Römer, Regine; Zhang, Erlin; Kainer, Karl Ulrich; Hort, Norbert

2017-06-01

Rare earth element Dy is one of the promising alloying elements for magnesium alloy as biodegradable implants. To understand the effect of Dy in solid solution on the degradation of Mg-Dy alloys in simulated physiological conditions, the present work studied the microstructure and degradation behavior of Mg-Dy alloys in cell culture medium. It is found the corrosion resistance enhances with the increase of Dy content in solid solution in Mg. This can be attributed to the formation of a relatively more corrosion resistant Dy-enriched film which decreases the anodic dissolution of Mg. Copyright © 2017 Elsevier B.V. All rights reserved.

Magnetic properties of Dy/Zr multilayers

International Nuclear Information System (INIS)

Luche, M.C.; Boyer, P.

1992-01-01

[Dy(xA)/Zr(30A)] n superlattices (x ≤ 30), were evaporated under ultra-high vacuum on Si(100) substrates. Magnetization measurements indicate that the antiferromagnetic transition occurring at 178K in bulk Dy is suppressed in the multilayers. This phenomenon is attributed to magnetoelastic effects induced by strains at Zr/Dy interfaces. A perpendicular magnetic anisotropy takes place for x ≤ 15. However, the magnetic anisotropy is found to depend markedly on the technique used for Dy deposition. (author). 11 refs., 4 figs

Heavy metal input to agricultural soils from irrigation with treated wastewater: Insight from Pb isotopes

Science.gov (United States)

Kloppmann, Wolfram; Cary, Lise; Psarras, Georgios; Surdyk, Nicolas; Chartzoulakis, Kostas; Pettenati, Marie; Maton, Laure

2010-05-01

A major objective of the EU FP6 project SAFIR was to overcome certain drawbacks of wastewater reuse through the development of a new irrigation technology combining small-scale modular water treatment plants on farm level and improved irrigation hardware, in the aim to lower the risks related to low quality water and to increase water use efficiency. This innovative technology was tested in several hydro-climatic contexts (Crete, Italy, Serbia, China) on experimental irrigated tomato and potato fields. Here we present the heavy metal variations in soil after medium-term (3 irrigation seasons from 2006-2008) use of treated municipal wastewater with a special focus on lead and lead isotope signatures. The experimental site is located in Chania, Crete. A matrix of plots were irrigated, combining different water qualities (secondary, primary treated wastewater, tap water, partially spiked with heavy metals, going through newly developed tertiary treatment systems) with different irrigation strategies (surface and subsurface drip irrigation combined with full irrigation and partial root drying). In order to assess small scale heavy metal distribution around a drip emitter, Pb isotope tracing was used, combined with selective extraction. The sampling for Pb isotope fingerprinting was performed after the 3rd season of ww-irrigation on a lateral profile from a drip irrigator (half distance between drip lines, i.e. 50cm) and three depth intervals (0-10, 10-20, 20-40 cm). These samples were lixiviated through a 3 step selective extraction procedure giving rise to the bio-accessible, mobile and residual fraction: CaCl2/NaNO3 (bio-accessible fraction), DPTA (mobile fraction), total acid attack (residual fraction). Those samples were analysed for trace elements (including heavy metals) and major inorganic compounds by ICP-MS. The extracted fractions were then analysed by Thermal Ionisation Mass Spectrometry (TIMS) for their lead isotope fingerprints (204Pb, 206Pb, 207Pb, 208Pb

Magnetooptic effects and Auger electron spectroscopy of two-layer NiFe-Dy and Fe-Dy films with nonuniform layers

International Nuclear Information System (INIS)

Ehdel'man, I.S.; Markov, V.V.; Khudyakov, A.E.; Ivantsov, R.D.; Bondarenko, G.V.; Ovchinnikov, S.G.; Kesler, V.G.; Parshin, A.S.; Ronzhin, I.P.

2001-01-01

Magneto-optical effects (magnetic circular dichroism and meridional Kerr effect) and element distribution with layer thickness in two-layer NiFe-Dy and Fe-Dy films, prepared by thermal sputtering of component in ultrahigh vacuum, are investigated. It is shown, that Dy in a two-layer film in the temperature range of 80-300 K makes constant contributions to both effects investigated which are approximately equal to the values of the effects observed in an isolated Dy film only at temperatures below the temperature T c of Dy transition into a ferromagnetic state (T c ∼ 100 K for the films under study). This behaviour of magneto-optical effects is assumed to be due to the influence of a NiFe layer spin system on magnetic state of a Dy layer, this influence is enhanced by the deep penetration of Ni and Fe ions into Dy layer as it follows from the data obtained using Auger electron spectroscopy [ru

2nd-order optical model of the isotopic dependence of heavy ion absorption cross sections for radiation transport studies

Science.gov (United States)

Cucinotta, Francis A.; Yan, Congchong; Saganti, Premkumar B.

2018-01-01

Heavy ion absorption cross sections play an important role in radiation transport codes used in risk assessment and for shielding studies of galactic cosmic ray (GCR) exposures. Due to the GCR primary nuclei composition and nuclear fragmentation leading to secondary nuclei heavy ions of charge number, Z with 3 ≤ Z ≥ 28 and mass numbers, A with 6 ≤ A ≥ 60 representing about 190 isotopes occur in GCR transport calculations. In this report we describe methods for developing a data-base of isotopic dependent heavy ion absorption cross sections for interactions. Calculations of a 2nd-order optical model solution to coupled-channel solutions to the Eikonal form of the nucleus-nucleus scattering amplitude are compared to 1st-order optical model solutions. The 2nd-order model takes into account two-body correlations in the projectile and target ground-states, which are ignored in the 1st-order optical model. Parameter free predictions are described using one-body and two-body ground state form factors for the isotopes considered and the free nucleon-nucleon scattering amplitude. Root mean square (RMS) matter radii for protons and neutrons are taken from electron and muon scattering data and nuclear structure models. We report on extensive comparisons to experimental data for energy-dependent absorption cross sections for over 100 isotopes of elements from Li to Fe interacting with carbon and aluminum targets. Agreement between model and experiments are generally within 10% for the 1st-order optical model and improved to less than 5% in the 2nd-order optical model in the majority of comparisons. Overall the 2nd-order optical model leads to a reduction in absorption compared to the 1st-order optical model for heavy ion interactions, which influences estimates of nuclear matter radii.

Tritium isotope separation from light and heavy water by bipolar electrolysis

International Nuclear Information System (INIS)

Petek, M.; Ramey, D.W.; Taylor, R.D.; Kobisk, E.H.

1980-01-01

A process for separating tritium from light and heavy water is described. Hydrogen is transferred at and through bipolar electrodes at rates H > D > T. In a cell containing several bipolar electrodes placed in series between two terminal electrodes, a flow of hydrogen is established from the terminal anode compartment toward the terminal cathode. An electrolyte feed containing tritium is continuously added to the system and is subsequently transported countercurrent to the hydrogen mass transfer. A cascaded system is established, in which effluent streams enriched and depleted in tritium can be withdrawn. The voltage drop is smaller at any bipolar electrode as compared to the voltage for normal electrolysis. Cell design is compact because isotope separation occurs at bipolar electrodes without evolution of gas. Isotope separation was demonstrated in laboratory cells where a steady-state tritium concentration gradient was attained. This gradient was in agreement with concentrations calculated from a derived mathematical model

Review of BNL heavy ion physics

International Nuclear Information System (INIS)

Miake, Yasuo.

1990-01-01

With an intent to search for a new state of matter, a relativistic heavy ion program was started in 1986 at BNL. Several interesting features have been reported from BNL-AGS heavy ion experiments, among which are: the enhanced K + /π + ratio and the larger left-angle m t right-angle for K + and proton. Comparisons between ∼pp, pA and SiA collisions are discussed for m t and dn/dy distributions. 33 refs., 9 figs., 1 tab

Effects of 3d-4f magnetic exchange interactions on the dynamics of the magnetization of Dy(III)-M(II)-Dy(III) trinuclear clusters.

Science.gov (United States)

Pointillart, Fabrice; Bernot, Kevin; Sessoli, Roberta; Gatteschi, Dante

2007-01-01

[{Dy(hfac)(3)}(2){Fe(bpca)(2)}] x CHCl(3) ([Dy(2)Fe]) and [{Dy(hfac)(3)}(2){Ni(bpca)(2)}]CHCl(3) ([Dy(2)Ni]) (in which hfac(-)=1,1,1,5,5,5-hexafluoroacetylacetonate and bpca(-)=bis(2-pyridylcarbonyl)amine anion) were synthesized and characterized. Single-crystal X-ray diffraction shows that [Dy(2)Fe] and [Dy(2)Ni] are linear trinuclear complexes. Static magnetic susceptibility measurements reveal a weak ferromagnetic exchange interaction between Ni(II) and Dy(III) ions in [Dy(2)Ni], whereas the use of the diamagnetic Fe(II) ion leads to the absence of magnetic exchange interaction in [Dy(2)Fe]. Dynamic susceptibility measurements show a thermally activated behavior with the energy barrier of 9.7 and 4.9 K for the [Dy(2)Fe] and [Dy(2)Ni] complexes, respectively. A surprising negative effect of the ferromagnetic exchange interaction has been found and has been attributed to the structural conformation of these trinuclear complexes.

Thermal neutrons thermoluminescence dosimetry using CaF2 + KBr e CaSO4: Dy + Br

International Nuclear Information System (INIS)

Leite, A.M.P.

1979-01-01

Cold-pressed samples of CaF 2 + KBr and CaSO 4 :Dy + KBr have been used in the thermal neutron detection by the thermoluminescence technique. The amount of 100 mg of the TL phosphor added to 80 mg of KBr showed to be the optimum mixture regarding sensitivity as well as the handling of the dosimeters. The detection is based on the self-irradiation of the phosphor by the Br isotopes activated by exposure to a neutron-gama field. The prompt dose and consequentely the gama contribution are erased by post-irradiation thermal annealing. A linear dependence has been found between the TL self-induced signal and the thermal neutron flux in the range 10 6 n.cm -2 .seg -1 -10 -12 n.cm -2 .seg -1 . The minimum detectable fluence has benn determined as 10 9 n.cm -2 and 10 6 n.cm -2 using pellets of CaF 2 + KBr and CaSO 4 :Dy + KBr, respectively. The main results suggest the use of CaSO 4 :Dy + KBr pellets and TL as a complementary technique for thermal neutron detection. (author) [pt

Production of heavy element and search for new isotopes at JAERI-RMS

Energy Technology Data Exchange (ETDEWEB)

Ikuta, Tomohiko [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-07-01

The new neutron deficient isotope {sup 209}Th and {sup 212}Pa have been produced in heavy ion induced fusion evaporation reactions. The evaporation residues were separated in-flight by the JAERI recoil mass separator (JAERI-RMS). The {alpha}-decay energy of {sup 209}Th and {sup 212}Pa are 8.080(50) MeV and 8.270(30) MeV, respectively. The corresponding half-lives are 3.8{sub -1.5}{sup +6.9} ms and 5.1{sub -1.9}{sup +6.1} ms. (author)

Measurements of Plutonium isotopes and the search for super-heavy elements via AMS

International Nuclear Information System (INIS)

Wallner, A.; Steier, P.; Golser, R.; Knie, K.; Kutschera, W.; Priller, A.; Hrnecek, E.; Jakopic, R.; Korschinek, G.

2006-01-01

Full text: Accelerator Mass Spectrometry (AMS) - being independent on the half-life of a radionuclide - provides a technique to determine isotope ratios with the highest sensitivity and allows the measurement of radionuclides over a wide dynamic range of concentration levels. A combination of AMS, Alpha Spectrometry and Liquid Scintillation Counting was used for the determination of the complete information on isotope ratios of Plutonium isotopes in different environmental reference samples (e.g. from the atolls of Mururoa and Fangataufa) and samples contaminated from nuclear reprocessing. Results for the isotopic ratios of the samples will be shown and the capabilities and detection limits achievable for determination of Pu will be discussed. The long-lived 244 Pu (t 1/2 = 80 Ma) and 247 Cm (t 1/2 = 15.6 Ma) have a very interesting application in astrophysics by detecting possible supernova-produced 244 Pu and 247 Cm in terrestrial archives. The expected extremely small concentrations of 244 Pu makes AMS the favorite method. The actual search for such long-lived extraterrestrial radionuclides and possible implications will be presented. The same method has also been explored for a pinprick-search of long-lived super-heavy elements in the mass region above Z=100. (author)

Selection of the process for the heavy water production using isotopic exchange amonia-hydrogen

International Nuclear Information System (INIS)

Guzman R, G.H.

1980-01-01

The utilization of the Petroleos Mexicanos ammonia plants for heavy water production by the isotopic exchange NH 3 -H 2 process is presented, in addition a description of the other heavy water production processes was presented. In the ammonia hydrogen process exist two possible alternatives for the operation of the system, one of them is to carry out the enrichment to the same temperature, the second consists in making the enrichment at two different temperatures (dual temperature process), an analysis was made to select the best alternative. The conclusion was that the best operation is the dual temperature process, which presents higher advantages according to the thermodynamics and engineering of the process. (author)

Isothermal sections at 500 deg C of the Dy-V-Al and Dy-Cr-Al systems in the aluminium rich regions

International Nuclear Information System (INIS)

Rykhal', R.M.; Zarechnyuk, O.S.; Mats'kiv, O.P.

1979-01-01

X-ray diffraction and microscopic analyses have been used to investigate the ternary system dysprosium-vanadium-aluminium in the aluminium rich region. In the system Dy-V-Al two ternary compounds have been found: DyV 2 Al 20 (cubic structure, CeCr 2 Al 20 type, a=14.54 A and approximately DyVAl 8 (hexagonal crystal system, structure unknown, a=10.86, c=17.71 A, c/a=1.631). In the system dysprosium-chromium-aluminium three ternary compounds have been found: DyCr 2 Al 20 (cubic structure, CeCr 2 Al 20 type, a=14.39), approximately equal to DyCrAl 8 ) hexagonal crystal system, structure type unkown a=10.75, c=17.60 A, c/a=1.637) and DyCr 4 Al 8 (tetragonal structure, CeMn 4 Al 8 type, a=8.87, c=5.04 A, c/a=0.568). Isothermal sections of the systems Dy-V-Al and Dy-Cr-Al have been plotted at 500 deg C

Phase equilibria in Dy-Cu-Al system at 500 deg C

International Nuclear Information System (INIS)

Kuz'ma, Yu.B.; Milyan, V.V.

1989-01-01

Using the methods of X-ray diffraction analysis a diagram of phase equilibria in Dy-Cu-Al system at 500 deg C is plotted. Boundaries of solid solutions on the basis of DyCu 2 , DyCu and DyAl 2 compounds are determined and homogeneity regions of ternary compounds Dy 2 (Cu, Al) 7 and Dy(CuAl) 5 are ascertained. Compounds DyCuAl 3 , Dy 4 Cu 4 Al 11 and Dy 5 Cu 6 Al 9 have been detected for the first time

Mechanoluminescence of Dy doped strontium aluminate nanophosphors

Energy Technology Data Exchange (ETDEWEB)

Sharma, Ravi, E-mail: rvsharma65@gmail.com [Department of Physics, Govt. Arts and Commerce Girls College, Raipur, C.G. 492001 (India); Bisen, D.P. [School of Studies in Physics and Astrophysics, Pt. Ravishankar Shukla University, Raipur, C.G. 492010 (India); Chandra, B.P. [Department of Postgraduate Studies and Research in Physics and Electronics, Rani Durgavati University, Jabalpur 482001 (India)

2015-12-15

Nanosized strontium aluminate phosphors activated with Dy{sup 3+} were prepared by a combustion method. Nanophosphor was prepared by this method at reaction temperatures as low as 600 °C. Powder X-ray diffraction (XRD), scanning electron microscope analysis was used to characterize the prepared product. The monoclinic phase was observed in the XRD pattern. The particle size of the samples was calculated around 35 nm. The SEM images show irregular shape of the prepared nanophosphor. Two peaks were found in the mechanoluminescence (ML) response curve plotted between time and ML intensity. The H{sub 3}BO{sub 3} added strontium aluminate phosphors activated with Dy show more bright ML peak as compared to the powders of SrAl{sub 2}O{sub 4}:Dy{sup 3+} without H{sub 3}BO{sub 3.} It was found that the PL and ML intensity increases with increasing concentration of Dy, it becomes maximum for 3% of Dy. The photoluminescence emission shows two intense fluorescence transitions peaks at 498 nm and 583 nm, {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} in the blue and {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} in the yellow-orange wavelength region. - Highlights: • Combustion synthesis route is used to prepare the SrAl{sub 2}O{sub 4}: Dy {sup 3+} nanophosphors. • The size of the synthesized sample was found to be in the nano-meter range. • The mechanoluminescence of SrAl{sub 2}O{sub 4}:Dy {sup 3+} nanophosphors is studied. • The photoluminescence of SrAl{sub 2}O{sub 4}: Dy {sup 3+} nanophosphors showed blue-shift as compared to bulk. • Effect of H{sub 3}BO{sub 3} on the mechanoluminescence of SrAl{sub 2}O{sub 4}:Dy{sup 3+} was studied.

Cytotoxic and genotoxic effect of the [166Dy]Dy/166Ho-EDTMP in vivo generator system in mice

International Nuclear Information System (INIS)

Pedraza-Lopez, Martha; Ferro-Flores, Guillermina; Arteaga de Murphy, Consuelo; Morales-Ramirez, Pedro; Piedras-Ross, Josefa; Murphy-Stack, Eduardo; Hernandez-Oviedo, Omar

2004-01-01

Multiple myeloma and other hematological malignancies have been treated by myeloablative radiotherapy/chemotherapy and subsequent stem cell transplantation. [ 166 Dy]Dy/ 166 Ho-ethylenediaminetetramethylene phosphonate (EDTMP) forms a stable in vivo generator system with selective skeletal uptake in mice; therefore, it could work as a potential and improved agent for marrow ablation. Induced bone marrow cytotoxicity and genotoxicity are determined by the reduction of reticulocytes (RET) and elevation of micronucleated reticulocyte (MN-RET) in peripheral blood and ablation by bone marrow histological studies. The aim of this study was to determine the bone marrow cytotoxic and genotoxic effect of the [ 166 Dy]Dy/ 166 Ho-EDTMP in vivo generator system in mice and to evaluate by histopathology its myeloablative potential. Enriched 166 Dy 2 O 3 was irradiated and [ 166 Dy]DyCl 3 was added to EDTMP in phosphate buffer (pH 8.0) in a molar ratio of 1:1.75. QC was determined by TLC. Dy-EDTMP complex was prepared the same way with nonirradiated dysprosium oxide. A group of BALB/c mice were intraperitoneally injected with the radiopharmaceutical and two groups of control animals were injected with the cold complex and with 0.9% sodium chloride, respectively. A blood sample was taken at the beginning of the experiments and every 48 h for 12 days postinjection. The animals were sacrificed, organs of interest taken out and the radioactivity determined. The femur was used for histological studies. Flow cytometry analysis was used to quantify the frequency of RET and MN-RET in the blood samples. The MCNP4B Monte Carlo computer code was used for dosimetry calculations. Radiochemical purity was 99% and the mean specific activity was 1.3 MBq/mg. The RET and MN-RET frequency were statistically different in the treatment at the end of the 12-day period demonstrating cytotoxicity and genotoxicity induced by the in vivo generator system. The histology studies show that there was

Regional and inter annual patterns of heavy metals, organochlorines and stable isotopes in narwhals (Monodon monoceros) from West Greenland

DEFF Research Database (Denmark)

Dietz, R.; Riget, F.; Hobson, K.A.

2004-01-01

Samples of 150 narwhals obtained in different years from two West Greenland areas, Avanersuaq and Uummannaq, were compared for concentrations of and regional differences in heavy metals and organochlorines and stable-carbon and nitrogen isotopes. Cadmium, Hg, and Se concentrations increased....../age composition of the data. PCB and DDT concentrations in West Greenland narwhals were half those found in East Greenland and Svalbard. Stable-carbon isotope ratios in muscle of 150 narwhals showed a decreasing trend in the first year when they gradually reduced their dependency on mother's milk, after which...... between stable isotope ratios and metal and OC concentrations....

Asteroids Dynamic Site-AstDyS

Science.gov (United States)

Knezevic, Zoran; Milani, Andrea

2012-08-01

The AstDyS online information service (http://hamilton.dm.unipi.it/astdys/) contains data on numbered and multi - opposition asteroids, including orbital elements, their uncertainty, proper elements, ephemerides with uncertainty, and more. AstDyS also provides additional scientific output computed from the raw observational data. This value added currently includes: more accurate orbits computed with advanced dynamical and observational error model s; their uncertainty, as expressed by the covariance matrix formalism; ephemerides computed on request for each observer, with uncertainty; mean and proper orbital elements (for this output, AstDyS is the primary source worldwide); statistical quality control, providing a rigorous observational error model. All this is available with a sophisticated web interface, providing multiple search functions and online computations as well as complete orbital and residual files. There are several ways in which the A stDyS service could be expanded and improved in the next future, like the explicit classification of asteroids into asteroid families, the classification of resonant asteroids, and an updated self - consistent population model (to be used, e.g., for survey simulations). The IAU Division I endorsed the proposal for AstDyS to become an IAU (permanent) service, which would include the IAU supervision of the AstDyS system, keeping under control the quality of the work and the continuous update under conditions of scientific competition.

The Ras antagonist, farnesylthiosalicylic acid (FTS, decreases fibrosis and improves muscle strength in dy/dy mouse model of muscular dystrophy.

Directory of Open Access Journals (Sweden)

Yoram Nevo

Full Text Available The Ras superfamily of guanosine-triphosphate (GTP-binding proteins regulates a diverse spectrum of intracellular processes involved in inflammation and fibrosis. Farnesythiosalicylic acid (FTS is a unique and potent Ras inhibitor which decreased inflammation and fibrosis in experimentally induced liver cirrhosis and ameliorated inflammatory processes in systemic lupus erythematosus, neuritis and nephritis animal models. FTS effect on Ras expression and activity, muscle strength and fibrosis was evaluated in the dy(2J/dy(2J mouse model of merosin deficient congenital muscular dystrophy. The dy(2J/dy(2J mice had significantly increased RAS expression and activity compared with the wild type mice. FTS treatment significantly decreased RAS expression and activity. In addition, phosphorylation of ERK, a Ras downstream protein, was significantly decreased following FTS treatment in the dy(2J/dy(2J mice. Clinically, FTS treated mice showed significant improvement in hind limb muscle strength measured by electronic grip strength meter. Significant reduction of fibrosis was demonstrated in the treated group by quantitative Sirius Red staining and lower muscle collagen content. FTS effect was associated with significantly inhibition of both MMP-2 and MMP-9 activities. We conclude that active RAS inhibition by FTS was associated with attenuated fibrosis and improved muscle strength in the dy(2J/dy(2J mouse model of congenital muscular dystrophy.

Genotoxic and cytotoxic damage by the therapeutic radiopharmaceutical [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP as in vivo generator system; Dano genotoxico y citotoxico por el radiofarmaco terpeutico [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP como sistema de generador in vivo

Energy Technology Data Exchange (ETDEWEB)

Pedraza L, M; Piedras R, J [Instituto Nacional de Ciencias Medicas y Nutricion, Salvador Zubiran. Vasco. de Quiroga 15, 14000 Mexico D.F. (Mexico); Ferro F, G; Morales R, P [ININ, Km. 36.5 Carretera Mexico-Toluca, Ocoyoacac, 52045 Estado de Mexico (Mexico); Murphy S, E [Hospital Santaelena, Mexico D.F. (Mexico); Hernandez O, O [Escuela Superior de Fisica y Matematicas, IPN, Mexico D.F. (Mexico)

2005-07-01

In patients with leukemias and multiple myeloma, the cure can be obtained to inclination of a bone marrow transplant (m.o.), for that which one is used a combination of external radiotherapy and chemotherapy with the consequent toxicity to healthy organs. The complex [{sup 166}Dy]Dy/{sup 166}Ho-ethylenediaminetetramethylenephosphonate ([{sup 166}Dy]Dy/{sup 166}Ho-EDTMP) it forms a generator system in vivo stable with bony selective likeness in mice therefore, this it could work as a therapeutic radiopharmaceutical for bone marrow ablation. The objective of this original work was to determine the genotoxic and cytotoxic damage produced by the [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP like a generator system in vivo by means of the reticulocytes reduction (RET) and micronucleus elevation in reticulocytes (RET-MN) in peripheral blood and to evaluate its myeloablative potential for histopathologic studies. It was irradiated {sup 166}Dy{sub 2}O{sub 3} enriched and it was add in form {sup 166}DyCI{sub 3} to the EDTMP in a softening media of phosphates (pH 8), the optimal molar relationship {sup 166}Dy: EDTMP was 1.7:1 and the radiochemical purity was evaluated by ITLC. The Dy:EDTMP complexes, non radioactive, its were prepared in the same way with non irradiated dysprosium oxide. A group of BALB/c mice was injected intraperitoneally with the radiopharmaceutical and two groups of control mice were injected with the non radioactive complex and with sodium chloride 0.9% respectively. Before injecting each one of the solutions it was take a basal sample of peripheral blood of the mouse tail and each 48 h post-injection during 12 d. The animals were sacrificed to obtain the organs of interest and to determine the radioactivity in each one. The femur was used for the histopathologic studies. The quantification of the frequency of RET and RET-MN was carried out by flow cytometry of the sanguine samples and the Monte Carlo code MCNP4B for the dosimetry calculations was used. The

Technical status study of heavy water enrichment

International Nuclear Information System (INIS)

Sukarsono; Imam Dahroni; Didik Herhady

2007-01-01

Technical status study of heavy water enrichment in Indonesia and also in the world has been done. Heavy water enrichment processes have been investigated were water distillation, hydrogen distillation, laser enrichment, electrolysis and isotop exchange. For the isotop exchange, the chemical pair can be used were water-hydrogen sulphite, ammonium-hydrogen, aminomethane-hydrogen, and water-hydrogen. For the isotope exchange, there was carried out by mono thermal or bi thermal. The highest producer of heavy water is Canada, and the other producer is USA, Norwegian and India. The processes be used in the world are isotope exchange Girdler Sulphide (GS), distillation and electrolysis. Research of heavy water carried out in Batan Yogyakarta, has a purpose to know the characteristic of heavy water purification. Several apparatus which has erected were 3 distillation column: Pyrex glass of 2 m tall, stainless steel column of 3 m tall and steel of 6 m tall. Electrolysis apparatus is 50 cell electrolysis and an isotope exchange unit which has catalyst: Ni- Cr 2 O 3 and Pt-Carbon. These apparatus were not ready to operate. (author)

Magnetic properties of the ternary carbide DyCoC2 studied by magnetization measurements, neutron diffraction and 161Dy Moessbauer spectroscopy

International Nuclear Information System (INIS)

Amanai, H.; Onodera, H.; Ohashi, M.; Matsuo, S.; Yamauchi, H.

1995-01-01

The magnetic properties of DyCoC 2 have been investigated by means of magnetization measurements, powder neutron diffraction and 161 Dy Moessbauer spectroscopy. The magnetization versus temperature curves of a single-crystalline sample reveal that the magnetic structure of DyCoC 2 is a simple collinear ferromagnetic one below T C =10.0 K. At 4.2 K, the magnitude of the Dy moment is 8.7(1)μ B , whose direction is defined by an angle of 38.0(5) from the a-axis toward the c-axis. The magnetic structure and the magnitude of the moment are also confirmed by the results of powder neutron diffraction experiments and 161 Dy Moessbauer spectroscopy, respectively. ((orig.))

UWIS isotope separator

Energy Technology Data Exchange (ETDEWEB)

Wojtasiewicz, A. [Warsaw Univ., Inst. of Experimental Physics, Nuclear Physics Div., Warsaw (Poland)

1997-12-31

Since 1995 the University of Warsaw Isotope Separator group has participated in the ISOL/IGISOL project at the Heavy Ion Cyclotron. This project consists in installation of an isotope separator (on line with cyclotron heavy ion beam) with a hot plasma ion source (ISOL system) and/or with an ion guide source (IGISOL system). In the report the short description of the present status of the project is presented. 2 figs, 10 refs.

Genotoxic and cytotoxic damage by the therapeutic radiopharmaceutical [166Dy]Dy/166Ho-EDTMP as in vivo generator system

International Nuclear Information System (INIS)

Pedraza L, M.; Piedras R, J.; Ferro F, G.; Morales R, P.; Murphy S, E.; Hernandez O, O.

2005-01-01

In patients with leukemias and multiple myeloma, the cure can be obtained to inclination of a bone marrow transplant (m.o.), for that which one is used a combination of external radiotherapy and chemotherapy with the consequent toxicity to healthy organs. The complex [ 166 Dy]Dy/ 166 Ho-ethylenediaminetetramethylenephosphonate ([ 166 Dy]Dy/ 166 Ho-EDTMP) it forms a generator system in vivo stable with bony selective likeness in mice therefore, this it could work as a therapeutic radiopharmaceutical for bone marrow ablation. The objective of this original work was to determine the genotoxic and cytotoxic damage produced by the [ 166 Dy]Dy/ 166 Ho-EDTMP like a generator system in vivo by means of the reticulocytes reduction (RET) and micronucleus elevation in reticulocytes (RET-MN) in peripheral blood and to evaluate its myeloablative potential for histopathologic studies. It was irradiated 166 Dy 2 O 3 enriched and it was add in form 166 DyCI 3 to the EDTMP in a softening media of phosphates (pH 8), the optimal molar relationship 166 Dy: EDTMP was 1.7:1 and the radiochemical purity was evaluated by ITLC. The Dy:EDTMP complexes, non radioactive, its were prepared in the same way with non irradiated dysprosium oxide. A group of BALB/c mice was injected intraperitoneally with the radiopharmaceutical and two groups of control mice were injected with the non radioactive complex and with sodium chloride 0.9% respectively. Before injecting each one of the solutions it was take a basal sample of peripheral blood of the mouse tail and each 48 h post-injection during 12 d. The animals were sacrificed to obtain the organs of interest and to determine the radioactivity in each one. The femur was used for the histopathologic studies. The quantification of the frequency of RET and RET-MN was carried out by flow cytometry of the sanguine samples and the Monte Carlo code MCNP4B for the dosimetry calculations was used. The radiochemical purity was 99% and in average the specific

Faraday effect in γ-Dy2S3 and c-Dy2O3 paramagnetic crystals

International Nuclear Information System (INIS)

Shelykh, A.I.

1987-01-01

Studies of spectral and temperature dependences of Faraday effect in γ-Dy 2 S 3 and C-Dy 2 O 3 paramagnetic crystals are conducted. Paramagnetism of these crystals is brought about by Dy 3+ ions. Estimation of the effect of such factors as the value of paramagnetic ion concentration, width of the forbidden band, crystallochemical composition on magnetooptical effect in the considered compounds of dysprosium is carried out on the basis of the obtained experimental data and theoretical analysis. It is shown, that the Faraday effect in the considered compounds of dysprosium as well as the value of paramagnetic moment may be regarded rather accurately in free ion approximation

Nuclear structure of light Ca and heavy Cr isotopes

International Nuclear Information System (INIS)

Buerger, A.

2007-01-01

In the present thesis, the shell structure in exotic nuclei has been investigated. The focus of the work was on finding new experimental data in neutron-rich Cr and proton-rich Ca isotopes. The investigation of light Ca isotopes concentrated on the nucleus 36 Ca which was produced in a knockout reaction from a radioactive 37 Ca beam. For 36 Ca, the excitation energy of the first 2 + state has been measured for the first time. Furthermore, momentum distributions were analyzed using a Monte-Carlo simulation of the knockout reaction. This analysis yielded the contributions of neutrons from individual orbitals to the total knockout cross section. In principle, these may be used to calculate spectroscopic factors, but such a calculation is hampered by difficulties of present knockout-reaction models in predicting precise single-particle cross sections. The measured branching ratio to the ground and excited states, on the other hand, is close to the predicted value. A remaining difference might be due to emission of protons which cannot be detected with the present experimental setup. Both the branching ratio and the large excitation energy are compatible with a large N=16 gap in 36 Ca that leads to relatively pure configurations both in the ground state and the excited 2 + state. As a by-product of the experiment, two excitation energies in the T=2 nuclei 32 Ar and 28 S have been confirmed, and two γ-ray transitions have been observed for the first time in 37 Ca. While the mirror energy differences in the T=2 pairs 36 Ca- 36 S, 32 Ar- 32 Si, and 28 S- 28 Mg can be reproduced in shell model calculations using a modified USD interaction, these modifications are not sufficient to explain the mirror energy differences for the pair 37 Ca- 37 Cl. In the heavy Cr isotopes, new experimental evidence for a sub-shell closure at N=32 was found in a measurement of B(E2) values using high-energy Coulomb excitation of radioactive beams. Prior to this experiment, the assumption of a

Room-temperature ferromagnetism in Dy films doped with Ni

International Nuclear Information System (INIS)

Edelman, I.; Ovchinnikov, S.; Markov, V.; Kosyrev, N.; Seredkin, V.; Khudjakov, A.; Bondarenko, G.; Kesler, V.

2008-01-01

Temperature, magnetic field and spectral dependences of magneto-optical effects (MOEs) in bi-layer films Dy (1-x) Ni x -Ni and Dy (1-x) (NiFe) x -NiFe were investigated, x changes from 0 to 0.06. Peculiar behavior of the MOEs was revealed at temperatures essentially exceeding the Curie temperature of bulk Dy which is explained by the magnetic ordering of the Dy layer containing Ni under the action of two factors: Ni impurities distributed homogeneously over the whole Dy layer and atomic contact of this layer with continues Ni layer. The mechanism of the magnetic ordering is suggested to be associated with the change of the density of states of the alloy Dy (1-x) Ni x owing to hybridization with narrow peaks near the Fermi level character for Ni

Test of the X(5) symmetry in {sup 156}Dy and {sup 178}Os by measurement of electromagnetic transition probabilities; Test der X(5)-Symmetrie in {sup 156}Dy und {sup 178}Os durch Messung elektromagnetischer Uebergangswahrscheinlichkeiten

Energy Technology Data Exchange (ETDEWEB)

Moeller, O.

2005-07-01

This work reports on results from two Recoil-Distance-Doppler-Shift lifetime measurements of excited states in {sup 155}Dy and {sup 178}Os. The experiments were carried out at the GASP spektrometer of the Laboratori Nazional i di Legnaro in combination with the Cologne plunger apparatus. The main purpose of the performed experiments was to test the predictions of the X(5) critical point symmetry in these two nuclei. In {sup 156}Dy and {sup 178}Os 29 lifetimes of excited states were derived using the Differential-Decay-Curve method. In weaker reaction channels the nuclei {sup 155}Dy, {sup 157}Dy and {sup 177}Os were populated. In these nuclei 32 additional lifetimes were measured, most of them for the first time. In order to calculate absolute transition probabilities from the measured lifetimes of the first excited band in {sup 156}Dy, essential branching ratios were derived from the measured data with a very small systematic error (<5%). The most important results can be summarized as mentioned below: Lifetimes measured in the first excited band, confirm that this nucleus can be located close to the critical point X(5). With model calculations, special criteria of the X(5) model were found that can be used to identify other X(5)-like nuclei. Using these criterias a new region of X(5)-like nuclei could be suggested within the osmium isotopes in the A=180 mass region. The measured lifetimes in {sup 178}Os confirm the consistency of a X(5) description in these nuclei. A comparision with the well established X(5)-like nuclei in the N=90 isotones gives an agreement with the X(5) description of at least the same quality. (orig.)

DySectAPI: Scalable Prescriptive Debugging

DEFF Research Database (Denmark)

Jensen, Nicklas Bo; Karlsson, Sven; Quarfot Nielsen, Niklas

We present the DySectAPI, a tool that allow users to construct probe trees for automatic, event-driven debugging at scale. The traditional, interactive debugging model, whereby users manually step through and inspect their application, does not scale well even for current supercomputers. While...... lightweight debugging models scale well, they can currently only debug a subset of bug classes. DySectAPI fills the gap between these two approaches with a novel user-guided approach. Using both experimental results and analytical modeling we show how DySectAPI scales and can run with a low overhead...

Effect of Ligand Substitution around the Dy(III) on the SMM Properties of Dual-Luminescent Zn-Dy and Zn-Dy-Zn Complexes with Large Anisotropy Energy Barriers: A Combined Theoretical and Experimental Magnetostructural Study.

Science.gov (United States)

Costes, Jean Pierre; Titos-Padilla, Silvia; Oyarzabal, Itziar; Gupta, Tulika; Duhayon, Carine; Rajaraman, Gopalan; Colacio, Enrique

2016-05-02

The new dinuclear Zn(II)-Dy(III) and trinuclear Zn(II)-Dy(III)-Zn(II) complexes of formula [(LZnBrDy(ovan) (NO3)(H2O)](H2O)·0.5(MeOH) (1) and [(L(1)ZnBr)2Dy(MeOH)2](ClO4) (3) (L and L(1) are the dideprotonated forms of the N,N'-2,2-dimethylpropylenedi(3-methoxysalicylideneiminato and 2-{(E)-[(3-{[(2E,3E)-3-(hydroxyimino)butan-2-ylidene ]amino}-2,2-dimethylpropyl)imino]methyl}-6-methoxyphenol Schiff base compartmental ligands, respectively) have been prepared and magnetostructurally characterized. The X-ray structure of 1 indicates that the Dy(III) ion exhibits a DyO9 coordination sphere, which is made from four O atoms coming from the compartmental ligand (two methoxy terminal groups and two phenoxido bridging groups connecting Zn(II) and Dy(III) ions), other four atoms belonging to the chelating nitrato and ovanillin ligands, and the last one coming to the coordinated water molecule. The structure of 3 shows the central Dy(III) ion surrounded by two L(1)Zn units, so that the Dy(III) and Zn(II) ions are linked by phenoxido/oximato bridging groups. The Dy ion is eight-coordinated by the six O atoms afforded by two L(1) ligands and two O atoms coming from two methanol molecules. Alternating current (AC) dynamic magnetic measurements of 1, 3, and the previously reported dinuclear [LZnClDy(thd)2] (2) complex (where thd = 2,2,6,6-tetramethyl-3,5-heptanedionato ligand) indicate single molecule magnet (SMM) behavior for all these complexes with large thermal energy barriers for the reversal of the magnetization and butterfly-shaped hysteresis loops at 2 K. Ab initio calculations on 1-3 show a pure Ising ground state for all of them, which induces almost completely suppressed quantum tunnelling magnetization (QTM), and thermally assisted quantum tunnelling magnetization (TA-QTM) relaxations via the first excited Kramers doublet, leading to large energy barriers, thus supporting the observation of SMM behavior. The comparison between the experimental and theoretical

Isotope effect in heavy/light water suspensions of optically active gold nanoparticles

Science.gov (United States)

Kutsenko, V. Y.; Artykulnyi, O. P.; Petrenko, V. I.; Avdeev, M. V.; Marchenko, O. A.; Bulavin, L. A.; Snegir, S. V.

2018-04-01

Aqueous suspensions of optically active gold nanoparticles coated with trisodium citrate were synthesized in light (H2O) water and mixture of light and heavy (H2O/D2O) water using the modified Turkevich protocol. The objective of the paper was to verify sensitivity of neutron scattering methods (in particular, neutron reflectometry) to the potential isotope H/D substitution in the stabilizing organic shell around particles in colloidal solutions. First, the isotope effect was studied with respect to the changes in the structural properties of metal particles (size, shape, crystalline morphology) in solutions by electron microscopy including high-resolution transmission electron microscopy from dried systems. The structural factors determining the variation in the adsorption spectra in addition to the change in the optical properties of surrounding medium were discussed. Then, neutron reflectometry was applied to the layered nanoparticles anchored on a silicon wafer via 3-aminopropyltriethoxysilane molecules to reveal the presence of deuterated water molecules in the shell presumably formed by citrate molecules around the metallic core.

Synthesis, structure and magnetic properties of DyAl2 nanoparticles

International Nuclear Information System (INIS)

Zhang, W.S.; Brueck, E.; Zhang, Z.D.; Tegus, O.; Li, W.F.; Si, P.Z.; Geng, D.Y.; Klaasse, J.C.P.; Buschow, K.H.J.

2006-01-01

DyAl 2 nanoparticles have been prepared by means of arc discharge in a mixture of argon and hydrogen gas. The structure of DyAl 2 nanoparticles is studied by means of X-ray diffraction, X-ray photoelectron spectroscopy, and high-resolution transmission electron microscopy. X-ray photoelectron spectroscopy shows that the as-prepared DyAl 2 nanoparticles are coated with a layer of Al 2 O 3 phase on the surface, and their sizes vary from 20 nm to about 100 nm. The DyAl 2 nanoparticles exhibit ferromagnetic properties that are different from bulk DyAl 2 compound. The gradual decrease of the magnetization with increasing temperature in a wide temperature range reveals the size distribution of the DyAl 2 nanoparticles. The magnetic-entropy changes are derived from the isothermal magnetization curves measured at different temperatures. The magnetic-entropy change of the DyAl 2 nanoparticles is lower than that of the bulk DyAl 2 material but has a broadened peak

Search for superdeformed bands in {sup 154}Dy

Energy Technology Data Exchange (ETDEWEB)

Nisius, D.; Janssens, R.V.F.; Khoo, T.L. [and others

1995-08-01

The island of superdeformation in the vicinity of the doubly magic {sup 152}Dy yrast superdeformed (SD) band is thought to be well understood in the framework of cranked mean field calculations. In particular, the calculations suggested that in {sup 154}Dy there should be no yrast or near yrast SD minimum in the 40-60 h spin range, where SD bands in this mass region are thought to be {sup 153}Dy nucleus, it is populated. However, with the presence of five SD bands in the neighboring necessary to ascertain if the addition of one single neutron diminishes the importance of shell effects to the extent that superdeformation can no longer be sustained. In an experiment utilizing the increased resolving power of the early implementation phase of Gammasphere, the reaction {sup 122}Sn({sup 36}S,4n) at 165 MeV was employed to populate high spin states in {sup 154}Dy. In a four-day run with 36 detectors, over one billion triple and higher fold coincidence events were recorded. One new SD band was identified and was assigned to {sup 154}Dy. From comparisons with the Im{sup (2)} moments of inertia of the SD bands in {sup 152}Dy and {sup 153}Dy, a configuration based on (514)9/2{sup 2} neutrons coupled to the {sup 152}Dy SD core was proposed. One unexpected and as yet unexplained feature of this new SD band is that the transition energies are almost identical to those of an excited SD band in {sup 153}Dy. It is also worth noting that the feeding of the yrast states is similar to that achieved by the deexcitation from the ensemble of all entry states in the reaction. This observation emphasizes the statistical nature of the decay-out process. A paper reporting these results was accepted for publication.

Combining emission inventory and isotope ratio analyses for quantitative source apportionment of heavy metals in agricultural soil.

Science.gov (United States)

Chen, Lian; Zhou, Shenglu; Wu, Shaohua; Wang, Chunhui; Li, Baojie; Li, Yan; Wang, Junxiao

2018-08-01

Two quantitative methods (emission inventory and isotope ratio analysis) were combined to apportion source contributions of heavy metals entering agricultural soils in the Lihe River watershed (Taihu region, east China). Source apportionment based on the emission inventory method indicated that for Cd, Cr, Cu, Pb, and Zn, the mean percentage input from atmospheric deposition was highest (62-85%), followed by irrigation (12-27%) and fertilization (1-14%). Thus, the heavy metals were derived mainly from industrial activities and traffic emissions. For Ni the combined percentage input from irrigation and fertilization was approximately 20% higher than that from atmospheric deposition, indicating that Ni was mainly derived from agricultural activities. Based on isotope ratio analysis, atmospheric deposition accounted for 57-93% of Pb entering soil, with the mean value of 69.3%, which indicates that this was the major source of Pb entering soil in the study area. The mean contributions of irrigation and fertilization to Pb pollution of soil ranged from 0% to 10%, indicating that they played only a marginally important role. Overall, the results obtained using the two methods were similar. This study provides a reliable approach for source apportionment of heavy metals entering agricultural soils in the study area, and clearly have potential application for future studies in other regions. Copyright © 2018 Elsevier Ltd. All rights reserved.

Effects of Dy{sub 71.5}Fe{sub 28.5} intergranular addition on the microstructure and the corrosion resistance of Nd–Fe–B sintered magnets

Energy Technology Data Exchange (ETDEWEB)

Liang, Liping; Ma, Tianyu, E-mail: maty@zju.edu.cn; Zhang, Pei; Yan, Mi, E-mail: mse_yanmi@zju.edu.cn

2015-06-15

To satisfy high-temperature applications, heavy rare-earth (RE) Dy is commonly introduced into the Nd–Fe–B sintered magnets to improve the coercivity. In addition to forming (Nd, Dy){sub 2}Fe{sub 14}B, Dy also exists in the intergranular RE-rich phase. Hence, understanding the effect of Dy on the electrochemical characteristics of the RE-rich phase and corrosion resistance of the magnet is of importance. In this work, eutectic alloy Dy{sub 71.5}Fe{sub 28.5} powders were added into the (Pr{sub 0.2}Nd{sub 0.8}){sub 12.3}Fe{sub bal}B{sub 6.1} magnet through binary-alloy approach to investigate the corrosion resistance of the magnet in electrochemical and hot/humid environments. The results demonstrate that Dy is enriched in the intergranular phase, improving its electrode potential and stability due to the higher electrode potential of Dy than Nd or Pr. As a consequence, the electrode potential difference between the 2:14:1 phase and the RE-rich phase is reduced, improving the corrosion resistance. Furthermore, formation of (Pr, Nd, Dy){sub 2}Fe{sub 14}B shell with stronger local anisotropy surrounding the 2:14:1 phase grains improves the coercivity with a slight remanence loss. Therefore, intergranular adding Dy–Fe alloy powders can obtain both high magnetic properties and good corrosion resistance simultaneously. - Highlights: • Eutectic Dy{sub 71.5}Fe{sub 28.5} powders were intergranular added to NdFeB sintered magnets. • The doped magnet showed improved corrosion resistance compared to Dy-free magnet. • Dy enrichment in RE-rich intergranular phase improved its electrode potential. • (Nd, Dy){sub 2}Fe{sub 14}B shell was expected to form in the surface of Nd{sub 2}Fe{sub 14}B grains. • Both corrosion resistance and coercivity were improved in Dy–Fe doped magnet.

Room-temperature ferromagnetism in Dy films doped with Ni

Energy Technology Data Exchange (ETDEWEB)

Edelman, I. [Kirensky Institute of Physics, Siberian Division, Russian Academy of Sciences, Akademgorodok, Krasnoyarsk 660036 (Russian Federation)], E-mail: ise@iph.krasn.ru; Ovchinnikov, S. [Kirensky Institute of Physics, Siberian Division, Russian Academy of Sciences, Akademgorodok, Krasnoyarsk 660036 (Russian Federation); Siberian Federal University, Av. Svobodnyi 71, Krasnoyarsk 660074 (Russian Federation); Markov, V.; Kosyrev, N.; Seredkin, V.; Khudjakov, A.; Bondarenko, G. [Kirensky Institute of Physics, Siberian Division, Russian Academy of Sciences, Akademgorodok, Krasnoyarsk 660036 (Russian Federation); Kesler, V. [Institute of Semiconductor Physics, Siberian Division, Russian Academy of Sciences, Av. Akademika Lavrent' eva 13, Novosibirsk 630090 (Russian Federation)

2008-09-01

Temperature, magnetic field and spectral dependences of magneto-optical effects (MOEs) in bi-layer films Dy{sub (1-x)}Ni{sub x}-Ni and Dy{sub (1-x)}(NiFe){sub x}-NiFe were investigated, x changes from 0 to 0.06. Peculiar behavior of the MOEs was revealed at temperatures essentially exceeding the Curie temperature of bulk Dy which is explained by the magnetic ordering of the Dy layer containing Ni under the action of two factors: Ni impurities distributed homogeneously over the whole Dy layer and atomic contact of this layer with continues Ni layer. The mechanism of the magnetic ordering is suggested to be associated with the change of the density of states of the alloy Dy{sub (1-x)}Ni{sub x} owing to hybridization with narrow peaks near the Fermi level character for Ni.

Accurate masses of unstable rare earth isotopes by ISOLTRAP

International Nuclear Information System (INIS)

Beck, D.; Ames, F.; Audi, G.

2000-05-01

Direct mass measurements of neutron-deficient rare earth isotopes in the vicinity of 146 Gd were performed with the Penning trap mass spectrometer ISOLTRAP at ISOLDE/CERN. This paper reports on the measurement of more than 40 isotopes of the elements Pr, Nd, Pm, Sm, Eu, Dy and Ho, that have been measured with a typical accuracy of δm ∼ 14 keV. An atomic mass evaluation has been performed taking into account other experimental mass values via a least-squares adjustment. The results of the adjustment are discussed. (orig.)

Fission properties of very heavy actinides

International Nuclear Information System (INIS)

Hoffman, D.C.

1979-01-01

The existing data on neutron-emission, kinetic-energy and mass distributions, and half-lives for spontaneous fission of the heavy actinides are reviewed. A comparison of the data for the Fm isotopes with heavier and lighter nuclides suggests that the properties of the heavy Fm isotopes may be unique and can qualitatively be explained on the basis of fragment shell effects, i.e., symmetric fission results in two fragments with configurations close to the doubly magic 132 Sn nucleus. The effect of excitation energy and the use of systematics and theoretical predictions of fission properties and half-lives in the identification of new heavy element isotopes is discussed. 54 references

Isotope effects: definitions and consequences for pharmacologic studies

International Nuclear Information System (INIS)

Van Langenhove, A.

1986-01-01

The use of stable isotope-labeled compounds for pharmacologic studies requires careful consideration of the nature of the stable isotope label (2H, 13C, 15N, 18O) and its position of incorporation in the molecule. When deuterium is used, improper positioning can lead to significant primary isotope effects. Primary isotope effects occur when the breaking of the bond to the heavy isotope is the rate-limiting step in a reaction (or metabolic transformation). A reaction will proceed slower for the molecule with the heavy isotope label because of the mass difference between the light and the heavy isotope. In addition to these primary isotope effects, smaller but nevertheless important secondary isotope effects, physicochemical isotope effects, active hydrogen/deuterium exchange, or isotope effects associated with either the enzyme-catalyzed biotransformation or the mass spectrometric ionization and fragmentation can be operative. In mechanistic studies, isotope effects are used to their advantage; however, in pharmacokinetic studies, the occurrence of isotope effects can lead to grossly misleading biologic and analytic results: the metabolism of the drug will differ when in vivo isotope effects are operative, and isotope effects occurring during the analysis procedure will obscure the true metabolic profile of the drug

Some Limitations in the Use of Plastic and Dyed Plastic Dosimeters

DEFF Research Database (Denmark)

Miller, Arne; Bjergbakke, Erling; McLaughlin, W. L.

1975-01-01

Several practical plastic and dyed plastic dosimeters were examined under irradiation conditions similar to those used for radiation processing of materials. Cellulose triacetate, polymethyl methacrylate, polyvinyl chloride, dyed polymethyl methacrylate, dyed Cellophane and dyed Nylon were given...

Nuclear structure of light Ca and heavy Cr isotopes

Energy Technology Data Exchange (ETDEWEB)

Buerger, A.

2007-07-01

In the present thesis, the shell structure in exotic nuclei has been investigated. The focus of the work was on finding new experimental data in neutron-rich Cr and proton-rich Ca isotopes. The investigation of light Ca isotopes concentrated on the nucleus {sup 36}Ca which was produced in a knockout reaction from a radioactive {sup 37}Ca beam. For {sup 36}Ca, the excitation energy of the first 2{sup +} state has been measured for the first time. Furthermore, momentum distributions were analyzed using a Monte-Carlo simulation of the knockout reaction. This analysis yielded the contributions of neutrons from individual orbitals to the total knockout cross section. In principle, these may be used to calculate spectroscopic factors, but such a calculation is hampered by difficulties of present knockout-reaction models in predicting precise single-particle cross sections. The measured branching ratio to the ground and excited states, on the other hand, is close to the predicted value. A remaining difference might be due to emission of protons which cannot be detected with the present experimental setup. Both the branching ratio and the large excitation energy are compatible with a large N=16 gap in {sup 36}Ca that leads to relatively pure configurations both in the ground state and the excited 2{sup +} state. As a by-product of the experiment, two excitation energies in the T=2 nuclei {sup 32}Ar and {sup 28}S have been confirmed, and two {gamma}-ray transitions have been observed for the first time in {sup 37}Ca. While the mirror energy differences in the T=2 pairs {sup 36}Ca-{sup 36}S, {sup 32}Ar-{sup 32}Si, and {sup 28}S-{sup 28}Mg can be reproduced in shell model calculations using a modified USD interaction, these modifications are not sufficient to explain the mirror energy differences for the pair {sup 37}Ca-{sup 37}Cl. In the heavy Cr isotopes, new experimental evidence for a sub-shell closure at N=32 was found in a measurement of B(E2) values using high

Cytotoxic and genotoxic effect of the [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP in vivo generator system in mice

Energy Technology Data Exchange (ETDEWEB)

Pedraza-Lopez, Martha [Departamento de Medicina Nuclear, Instituto Nacional de Ciencias Medicas y Nutricion, Salvador Zubiran, Delegacion Tlalpan, Mexico DF 14000 (Mexico); Ferro-Flores, Guillermina [Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca, Ocoyoacac, Estado de Mexico, CP 52045 (Mexico); Arteaga de Murphy, Consuelo [Departamento de Medicina Nuclear, Instituto Nacional de Ciencias Medicas y Nutricion, Salvador Zubiran, Delegacion Tlalpan, Mexico DF 14000 (Mexico)]. E-mail: consuelo_murphy@yahoo.com.mx; Morales-Ramirez, Pedro [Instituto Nacional de Investigaciones Nucleares, Carretera Mexico-Toluca, Ocoyoacac, Estado de Mexico, CP 52045 (Mexico); Piedras-Ross, Josefa [Departamento de Medicina Nuclear, Instituto Nacional de Ciencias Medicas y Nutricion, Salvador Zubiran, Delegacion Tlalpan, Mexico DF 14000 (Mexico); Murphy-Stack, Eduardo [Hospital Santaelena, Mexico DF (Mexico); Hernandez-Oviedo, Omar [Escuela Superior de Fisica y Matematicas, IPN, Mexico DF (Mexico)

2004-11-01

Multiple myeloma and other hematological malignancies have been treated by myeloablative radiotherapy/chemotherapy and subsequent stem cell transplantation. [{sup 166}Dy]Dy/{sup 166}Ho-ethylenediaminetetramethylene phosphonate (EDTMP) forms a stable in vivo generator system with selective skeletal uptake in mice; therefore, it could work as a potential and improved agent for marrow ablation. Induced bone marrow cytotoxicity and genotoxicity are determined by the reduction of reticulocytes (RET) and elevation of micronucleated reticulocyte (MN-RET) in peripheral blood and ablation by bone marrow histological studies. The aim of this study was to determine the bone marrow cytotoxic and genotoxic effect of the [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP in vivo generator system in mice and to evaluate by histopathology its myeloablative potential. Enriched {sup 166}Dy{sub 2}O{sub 3} was irradiated and [{sup 166}Dy]DyCl{sub 3} was added to EDTMP in phosphate buffer (pH 8.0) in a molar ratio of 1:1.75. QC was determined by TLC. Dy-EDTMP complex was prepared the same way with nonirradiated dysprosium oxide. A group of BALB/c mice were intraperitoneally injected with the radiopharmaceutical and two groups of control animals were injected with the cold complex and with 0.9% sodium chloride, respectively. A blood sample was taken at the beginning of the experiments and every 48 h for 12 days postinjection. The animals were sacrificed, organs of interest taken out and the radioactivity determined. The femur was used for histological studies. Flow cytometry analysis was used to quantify the frequency of RET and MN-RET in the blood samples. The MCNP4B Monte Carlo computer code was used for dosimetry calculations. Radiochemical purity was 99% and the mean specific activity was 1.3 MBq/mg. The RET and MN-RET frequency were statistically different in the treatment at the end of the 12-day period demonstrating cytotoxicity and genotoxicity induced by the in vivo generator system. The

The ternary systems Sc-Sm(Dy)-Si at 870 K

International Nuclear Information System (INIS)

Kotur, B.Ya.; Mokra, I.Ya.; Toporinskij, A.Ya.

1991-01-01

Isothermal cross sections of the ternary systems Sc-Sm-Si and Sc-Dy-Si at 870 K have been plotted. Investigation of scandium and disprosium in ternary systems have been examined by X-ray diffraction and microstructure analysis. Besides literary data on binary systems Sc-Si, Sm-Si, Dy-Si have been used. Formation of limited (Sc-Sm-Si, Sc-Dy-Si) and continuous (Sc-Dy-Si) solid solutions based on bisilicides of Sc and Sm(Dy) is discovered. Two and five ternary compounds in Sc-Sm-Si and Sc-Dy-Si systems have been determined and their crystal structure has been established. When investigating of Sc-(rare earth element)-Si ternary systems and should take into account the specific interaction of scandium and samarium with REE

Microspheres labelled with short-lived isotopes: Development and application for tumors treatment (Experimental study)

International Nuclear Information System (INIS)

Drozdovsky, B.Y.; Rosiev, R.A.; Goncharova, A.Y.; Skvortsov, V.G.; Petriev, V.M.; Grigoriev, A.N.; Schischkanov, N.G.

1997-01-01

Analysis of the conducted studies strongly suggests the possibility of usage of the domestic protein microspheres as a vehicle for radionuclide. The neutron-activating method of RPP production enables to utilize a broad spectrum of short-living isotopes that can be delivered into the target organ and anchored there for a long time. Good treatment results were obtained in case of the experimentally induced rheumatoid arthritis in rats after intraarticular loading of 165 Dy-hMSA. Mathematical calculations show that homogeneous distribution of RPP in human articulation cavity with the square of 100 cm 2 can be achieved when the quantity of administered particles exceeds 3000. On the example of 165 Dy-hMSA energy characteristic distribution we demonstrated that the absorbed dose for damaged cells at 2mm distance from the radioactive source is 7 times less than the one for a sphere of 2mm diameter. Analysis of dosimetric data in case of intratumoral loading of 165 Dy-hMSA also point out the necessity of the absorbed dose calculation methods taking into account the distance from the source and possible heterogeneity of RPP distribution inside the tumor to be employed. The prolonged RPP detention in the target causing no essential morphological and functional changes was achieved by embolization on the level of septal and interlobular arteries and of efferent arterioles in the animal's renal. The uniformity of microsphere distribution in the organ and their accumulation in tumors depends on the number of particles being administered. Investigations carried out suggest the efficacy of radionuclide therapy application for treatment of oncological and heavy somatic diseases. They also indicate the necessity of further investigations aimed to optimize the usage of microspheres as a radionuclide carrier usage and to work out the criteria of dosimetric planning

Microspheres labelled with short-lived isotopes: Development and application for tumors treatment (Experimental study)

Energy Technology Data Exchange (ETDEWEB)

Drozdovsky, B.Y.; Rosiev, R.A.; Goncharova, A.Y.; Skvortsov, V.G.; Petriev, V.M.; Grigoriev, A.N.; Schischkanov, N.G. [Medical Radiological Research Centre RAMS, Kaluga Region, (Russian Federation)

1997-10-01

Analysis of the conducted studies strongly suggests the possibility of usage of the domestic protein microspheres as a vehicle for radionuclide. The neutron-activating method of RPP production enables to utilize a broad spectrum of short-living isotopes that can be delivered into the target organ and anchored there for a long time. Good treatment results were obtained in case of the experimentally induced rheumatoid arthritis in rats after intraarticular loading of {sup 165}Dy-hMSA. Mathematical calculations show that homogeneous distribution of RPP in human articulation cavity with the square of 100 cm{sup 2} can be achieved when the quantity of administered particles exceeds 3000. On the example of {sup 165}Dy-hMSA energy characteristic distribution we demonstrated that the absorbed dose for damaged cells at 2mm distance from the radioactive source is 7 times less than the one for a sphere of 2mm diameter. Analysis of dosimetric data in case of intratumoral loading of {sup 165}Dy-hMSA also point out the necessity of the absorbed dose calculation methods taking into account the distance from the source and possible heterogeneity of RPP distribution inside the tumor to be employed. The prolonged RPP detention in the target causing no essential morphological and functional changes was achieved by embolization on the level of septal and interlobular arteries and of efferent arterioles in the animal`s renal. The uniformity of microsphere distribution in the organ and their accumulation in tumors depends on the number of particles being administered. Investigations carried out suggest the efficacy of radionuclide therapy application for treatment of oncological and heavy somatic diseases. They also indicate the necessity of further investigations aimed to optimize the usage of microspheres as a radionuclide carrier usage and to work out the criteria of dosimetric planning 25 refs.

Microstructures and mechanical properties of Mg–Zn–Zr–Dy ...

Indian Academy of Sciences (India)

Microstructures and phase compositions of as-cast and extruded ZK60–Dy ( = 0–5) alloys were analysed by optical microscope, scanning electron microscope, X-ray diffraction and differential scanning calorimetry. Meanwhile, the tensile mechanical property was tested.With increasing Dy content, Mg–Zn–Dy new phase ...

Therapeutical radiopharmaceuticals based In vivo generator system [166 Dy] Dy/166 Ho

International Nuclear Information System (INIS)

Ferro F, G.; Garcia S, L.; Monroy G, F.; Tendilla, J.I.; Pedraza L, M.; Murphy, C.A. de

2002-01-01

At the idea to administer to a patient a molecule containing in it structure a father radionuclide, with a half life enough large which allows to the radiolabelled molecule to take up position specifically in a white tissue and decaying In vivo to the daughter radionuclide with properties potentially therapeutic, it is known as In vivo generator system. In this work the preparation and the preliminary dosimetric valuations of radiopharmaceuticals based In vivo generator system 166 Dy Dy/ 166 Ho for applications in radioimmunotherapy, in the treatment of the rheumatoid arthritis and in the bone marrow ablation (m.o.) for candidates patients to bone marrow transplant are presented. (Author)

Luminescence studies on Dy3+ and Dy3+:Eu3+ co-doped boro-phosphate glasses for WLED applications

Science.gov (United States)

Vijayakumar, M.; Uma, V.; Arunkumar, S.; Marimuthu, K.

2015-06-01

Dy3+ and Dy3+:Eu3+ co-doped boro-phosphate glasses have been prepared and optically characterized using absorption, luminescence and decay measurements. The Nephelauxetic ratios (β), Bonding parameters (δ) and Judd-Ofelt (JO) intensity parameters Ωλ (λ = 2, 4 and 6) were calculated to study the nature of the environment around the RE3+ ions in the prepared glasses. The yellow to blue (Y/B) intensity ratio and the chromaticity color coordinates were calculated from the luminescence measurements. The lifetimes of the 4F9/2 excited level were measured using decay curves and is found to decrease in the Dy3+:Eu3+ co-doped glass due to the occurrence of resonant energy transfer between Dy3+-Eu3+ ions and the non-exponential decay rates have been fitted with Inokuti-Hirayama (IH) model. The decay curves are well fitted for S= 6 suggesting that the interaction between active ions for the energy transfer is of dipole-dipole nature.

CaSO4: Dy + Teflon thermoluminescent dosemeters

International Nuclear Information System (INIS)

Campos, L.L.

1986-01-01

A pellet dosemeter of CaSO 4 : Dy + Teflon was developed at IPEN. CaSO 4 : Dy thermoluminescent phosphor, grown in the Dosimetric Materials Production Laboratory was chosen, due to its high sensitivity, ease of preparation and comparatively low cost. Pellets were produced by cold pressing and sintering a mixture of CaSO 4 : Dy and Teflon powders. Extensive work was done to study in detail all CaSO 4 : Dy pellets characteristics from the point of view of dosimetry with the purpose of introducing it in the routine use. A filter combination providing an energy independent response from 20 KeV to 1,25 MeV was obtained. The dosemeter consists of three pellets sealed between two thin plastic sheets and placed under plastic and lead filters. The combination of these tree filters allows the exposure as well as the energy determination of an unknown source. (Author) [pt

Determination of heavy water in heavy water - light water mixtures

International Nuclear Information System (INIS)

Sanhueza M, A.

1986-01-01

A description about experimental methodology to determine isotopic composition of heavy water - light water mixtures is presented. The employed methods are Nuclear Magnetic Resonance Spectroscopy, for measuring heavy water concentrations from 0 to 100% with intervals of 10% approx., and mass Spectrometry, for measuring heavy water concentrations from 0.1 to 1% with intervals of 0.15% approx., by means of an indirect method of Dilution. (Author)

Band mixing in /sup 160/Dy

Energy Technology Data Exchange (ETDEWEB)

Hasiza, M L; Singh, K; Sahota, H S [Punjabi Univ., Patiala (India). Dept. of Physics

1982-11-01

The intensities of the gamma transitions in /sup 160/Dy have been measured precisely by a 45 cc Ge(Li) detector. Unequal quadrupole moments for the ground and gamma vibrational bands have been proposed in order to remove the inconsistencies in the values of band mixing parameter Z sub(gamma) for this doubly even deformed nucleus of /sup 160/Dy.

Mechanistic Insights into Dye-Decolorizing Peroxidase Revealed by Solvent Isotope and Viscosity Effects

Energy Technology Data Exchange (ETDEWEB)

Shrestha, Ruben [Department; Huang, Gaochao [Department; Meekins, David A. [Department; Geisbrecht, Brian V. [Department; Li, Ping [Department

2017-08-18

Dye-decolorizing peroxidases (DyPs) are a family of H2O2-dependent heme peroxidases that have shown potential applications in lignin degradation and valorization. However, the DyP kinetic mechanism remains underexplored. Using structural biology and solvent isotope (sKIE) and viscosity effects, many mechanistic characteristics have been determined for the B-class ElDyP from Enterobacter lignolyticus. Its structure revealed that a water molecule acts as the sixth axial ligand and two channels at diameters of ~3.0 and 8.0 Å lead to the heme center. A conformational change of ERS* to ERS, which have identical spectral characteristics, was proposed as the final step in DyPs’ bisubstrate Ping-Pong mechanism. This step is also the rate-determining step in ABTS oxidation. The normal KIE of wild-type ElDyP with D2O2 at pD 3.5 suggested that compound 0 deprotonation by the distal aspartate is rate-limiting in the formation of compound I, which is more reactive under acidic pH than under neutral or alkaline pH. The viscosity effects and other biochemical methods implied that the reducing substrate binds with compound I instead of the free enzyme. The significant inverse sKIEs of kcat/KM and kERS* suggested that the aquo release in ElDyP is mechanistically important and may explain the enzyme’s adoption of two-electron reduction for compound I. The distal aspartate is catalytically more important than the distal arginine and plays key roles in determining ElDyP’s optimum acidic pH. The kinetic mechanism of D143H-ElDyP was also briefly studied. The results obtained will pave the way for future protein engineering to improve DyPs’ lignolytic activity.

Coercivity enhancement in hot deformed Nd2Fe14B-type magnets by doping low-melting RCu alloys (R = Nd, Dy, Nd + Dy)

Science.gov (United States)

Lee, Y. I.; Huang, G. Y.; Shih, C. W.; Chang, W. C.; Chang, H. W.; You, J. S.

2017-10-01

Magnetic properties of the anisotropic NdFeB magnets prepared by hot pressing followed by die-upsetting NdFeB MQU-F powders doped with low-melting RCu alloy powders were explored, where RCu stands for Nd70Cu30, Dy70Cu30 and (Nd0.5Dy0.5)70Cu30, respectively. In addition, the post-annealing at 600 °C was employed to modify the microstructures and the magnetic properties of the hot deformed magnets. It is found that doping RCu alloy powders is effective in enhancing the coercivity of the hot deformed NdFeB magnets from 15.1 kOe to 16.3-19.5 kOe. For Nd70Cu30-doped magnets, the increment of coercivity is only 1.2 kOe. Meanwhile, Dy70Cu30-doped and (Nd0.5Dy0.5)70Cu30-doped magnets show an almost identical enhancement of coercivity of about 4.4 kOe. Importantly, the latter magnet shows a beneficial effect of reducing the usage of Dy from 1.6 wt% to 0.8 wt%. TEM analysis shows that nonmagnetic Nd, Dy and Cu appear at grain boundary and isolate the magnetic grains, leading to an enhancement of coercivity. Doping lower melting point Dy-lean (Nd0.5Dy0.5)70Cu30 powders into commercial MQU-F powders for making high coercivity hot deformed NdFeB magnets might be a potential and economic way for mass production.

[Determination of deuterium concentration in foods and influence of water with modified isotopic composition on oxidation parameters and heavy hydrogen isotopes content in experimental animals].

Science.gov (United States)

Basov, A A; Bykov, I M; Baryshev, M G; Dzhimak, S S; Bykov, M I

2014-01-01

The article presents the results of the study of the deuterium (D) content in food products as well as the influence of deuterium depleted water (DDW) on the concentration of heavy hydrogen isotopes in the blood and lyophilized tissues of rats. The most significant difference in the content of D was found between potato and pork fat, which indexes the standard delta notation (δ) D in promille, related to the international standard SMOW (Standard Mean Ocean of Water) amounted to -83,2 per thousand and -250,7 per thousand, respectively (phydrogen atoms in the body. The data obtained in the experimental modeling of the diet of male Wistar rats in the age of 5-6 mo (weight 235 ± 16 g) using DDW (δD = -743,2 per thousand) instead of drinking water (δD = -37,0 per thousand) with identical mineral composition showed that after 2 weeks significant (p tissue") is due to different rates ofisotopic exchange reactions in plasma and tissues (liver, kidney, heart), which can be explained by entering into the composition of a modified diet of organic substrates with more than DDW concentration D, which are involved in the construction of cellular structures and eventually lead to a redistribution of D and change direction of D/H gradient "plasmaisotopic composition, aimed at reducing the level of heavy non-radioactive atoms will allow the targeted nutritional correction of prooxidant-antioxidant status of the population in areas with adverse environmental conditions, stimulating by created isotopic D/H gradient cytoprotective mechanisms influencing the various components of nonspecific protection, including free radical oxidation processes. And then again, periodic assessment of the isotopic composition of nutrients will monitor the quality of food consumed by the population, and if

Nickel distribution and isotopic fractionation in a Brazilian lateritic regolith: Coupling Ni isotopes and Ni K-edge XANES

Science.gov (United States)

Ratié, G.; Garnier, J.; Calmels, D.; Vantelon, D.; Guimarães, E.; Monvoisin, G.; Nouet, J.; Ponzevera, E.; Quantin, C.

2018-06-01

Ultramafic (UM) rocks are known to be nickel (Ni) rich and to weather quickly, which makes them a good candidate to look at the Ni isotope systematics during weathering processes at the Earth's surface. The present study aims at identifying the Ni solid speciation and discussing the weathering processes that produce Ni isotope fractionation in two deep laterite profiles under tropical conditions (Barro Alto, Goiás State, Brazil). While phyllosilicates and to a lower extent goethite are the main Ni-bearing phases in the saprolitic part of the profile, iron (Fe) oxides dominate the Ni budget in the lateritic unit. Nickel isotopic composition (δ60Ni values) has been measured in each unit of the regolith, i.e., rock, saprock, saprolite and laterite (n = 52). δ60Ni varies widely within the two laterite profiles, from -0.10 ± 0.05‰ to 1.43 ± 0.05‰, showing that significant Ni isotope fractionation occurs during the weathering of UM rocks. Overall, our results show that during weathering, the solid phase is depleted in heavy Ni isotopes due to the preferential sorption and incorporation of light Ni isotopes into Fe oxides; the same mechanisms likely apply to the incorporation of Ni into phyllosilicates (type 2:1). However, an isotopically heavy Ni pool is observed in the solid phase at the bottom of the saprolitic unit. This feature can be explained by two hypotheses that are not mutually exclusive: (i) a depletion in light Ni isotopes during the first stage of weathering due to the preferential dissolution of light Ni-containing minerals, and (ii) the sorption or incorporation of isotopically heavy Ni carried by percolating waters (groundwater samples have δ60Ni of 2.20 and 2.27‰), that were enriched in heavy Ni isotopes due to successive weathering processes in the overlying soil and laterite units.

Gas-centrifuge unit and centrifugal process for isotope separation

International Nuclear Information System (INIS)

Stark, T.M.

1979-01-01

An invention involving a process and apparatus for isotope-separation applications such as uranium-isotope enrichment is disclosed which employs cascades of gas centrifuges. A preferred apparatus relates to an isotope-enrichment unit which includes a first group of cascades of gas centrifuges and an auxiliary cascade. Each cascade has an input, a light-fraction output, and a heavy-fraction output for separating a gaseous-mixture feed including a compound of a light nuclear isotope and a compound of a heavy nuclear isotope into light and heavy fractions respectively enriched and depleted in the light isotope. The cascades of the first group have at least one enriching stage and at least one stripping stage. The unit further includes means for introducing a gaseous-mixture feedstock into each input of the first group of cascades, means for withdrawing at least a portion of a product fraction from the light-fraction outputs of the first group of cascades, and means for withdrawing at least a portion of a waste fraction from the heavy-fraction outputs of the first group of cascades. The isotope-enrichment unit also includes a means for conveying a gaseous-mixture from a light-fraction output of a first cascade included in the first group to the input of the auxiliary cascade so that at least a portion of a light gaseous-mixture fraction produced by the first group of cascades is further separated into a light and a heavy fraction by the auxiliary cascade. At least a portion of a product fraction is withdrawn from the light fraction output of the auxiliary cascade. If the light-fraction output of the first cascade and the heavy-fraction output of the auxiliary cascade are reciprocal outputs, the concentraton of the light isotope in the heavy fraction produced by the auxiliary cascade essentially equals the concentration of the light isotope in the gaseous-mixture feedstock

Reddish-orange, neutral and warm white emissions in Eu3+, Dy3+ and Dy3+/Eu3+ doped CdO-GeO2-TeO2 glasses

Science.gov (United States)

Rodríguez-Carvajal, David A.; Meza-Rocha, A. N.; Caldiño, U.; Lozada-Morales, R.; Álvarez, E.; Zayas, Ma. E.

2016-11-01

Eu3+, Dy3+ and Dy3+/Eu3+ doped CdO-GeO2-TeO2 glasses were prepared using the melt-quenching process and analyzed by X-diffraction, Raman spectroscopy, excitation and emission spectra, and emission decay time profiles. The lack of X ray diffraction peaks revealed that all samples are amorphous. Vibrational modes associated with Tesbnd Osbnd Te and Gesbnd Osbnd Ge related bonds and molecular oxygen were detected by Raman spectroscopy. The luminescence characteristics were studied upon excitations that correspond with the emission of InGaN (370-420 nm) based LEDs. The Eu3+ singly doped glass displayed reddish-orange global emission, with x = 0.601 and y = 0.349 CIE1931 chromaticity coordinates, upon 393 nm excitation. Neutral emission with x = 0.373 and y = 0.412 CIE1931 chromaticity coordinates and correlated color temperature (CCT) of 4400 K, was achieved in the Dy3+ singly doped glass excited at 388 nm. The Dy3+/Eu3+ co-doped glass exhibited warm, neutral and soft warm white emissions with CCT values of 3435, 4153 and 2740 K, under excitations at 382, 388 and 393 nm, respectively, depending mainly on the Dy3+ and Eu3+ relative excitation. The Dy3+ excitation bands observed in the Dy3+/Eu3+ glass by monitoring the 611 nm Eu3+ emission, suggest that Dy3+ → Eu3+ energy transfer takes place, despite the fact that the Dy3+ emission decays in the Dy3+ and Dy3+/Eu3+ doped glass, remain without changes. The shortening of Eu3+ decay in presence of Dy3+ was attributed to an Eu3+ → Dy3+ non-radiative energy transfer process, which according with the Inokuti-Hirayama model might be dominated through an electric quadrupole-quadrupole interaction, with efficiency and probability of 5.5% and 51.6 s-1, respectively.

[Fractionation of hydrogen stable isotopes in the human body].

Science.gov (United States)

Siniak, Iu E; Grigor'ev, A I; Skuratov, V M; Ivanova, S M; Pokrovskiĭ, B G

2006-01-01

Fractionation of hydrogen stable isotopes was studied in 9 human subjects in a chamber with normal air pressure imitating a space cabin. Mass-spectrometry of isotopes in blood, urine, saliva, and potable water evidenced increases in the contents of heavy H isotope (deuterium) in the body liquids as compared with water. These results support one of the theories according to which the human organism eliminates heavy stable isotopes of biogenous chemical elements.

Therapeutical radiopharmaceuticals based In vivo generator system [{sup 166} Dy] Dy/{sup 166} Ho; Radiofarmacos terapeuticos basados en un sistema de generador In vivo [{sup 166}Dy] Dy/{sup 166}Ho

Energy Technology Data Exchange (ETDEWEB)

Ferro F, G.; Garcia S, L.; Monroy G, F.; Tendilla, J.I. [Gerencia de Aplicaciones Nucleares en la Salud, ININ, A.P. 18-1027, 11801 Mexico D.F. (Mexico); Pedraza L, M.; Murphy, C.A. de [Departamento de Medicina Nuclear, Instituto Nacional de Pediatria, Mexico D.F. (Mexico)

2002-07-01

At the idea to administer to a patient a molecule containing in it structure a father radionuclide, with a half life enough large which allows to the radiolabelled molecule to take up position specifically in a white tissue and decaying In vivo to the daughter radionuclide with properties potentially therapeutic, it is known as In vivo generator system. In this work the preparation and the preliminary dosimetric valuations of radiopharmaceuticals based In vivo generator system {sup 166} Dy Dy/{sup 166} Ho for applications in radioimmunotherapy, in the treatment of the rheumatoid arthritis and in the bone marrow ablation (m.o.) for candidates patients to bone marrow transplant are presented. (Author)

Properties of alginate fiber spun-dyed with fluorescent pigment dispersion.

Science.gov (United States)

Wang, Ping; Tawiah, Benjamin; Tian, Anli; Wang, Chunxia; Zhang, Liping; Fu, Shaohai

2015-03-15

Spun-dyed alginate fiber was prepared by the spun-dyeing method with the mixture of fluorescent pigment dispersion and sodium alginate fiber spinning solution, and its properties were characterized by SEM, TGA, DSC, and XRD. The results indicate that fluorescent pigment dispersion prepared with esterified poly (styrene-alt maleic acid) had excellent compatibility with sodium alginate fiber spinning solution, and small amount of fluorescent pigment could reduce the viscosity of spun-dyed spinning solutions. SEM photo of spun-dyed alginate fiber indicated that fewer pigment particles deposited on its surface. TGA, DSC, and XRD results suggested that thermal properties and crystal phase of spun-dyed alginate fibers had slight changes compared to the original alginate fibers. The fluorescence intensity of spun-dyed alginate fiber reached its maximum when the content of fluorescent pigment was 4%. The spun-dyed alginate fiber showed excellent rubbing and washing fastness. Copyright © 2014 Elsevier Ltd. All rights reserved.

Electrical and magnetic transport properties of DyTiGe

International Nuclear Information System (INIS)

Dagula, W.; Tegus, O.; Li, X.W.; Zhang, L.; Brueck, E.; Boer, F.R. de; Buschow, K.H.J.

2004-01-01

Electrical resistivity and magnetoresistance of DyTiGe were investigated as a function of temperature and magnetic field. DyTiGe is an antiferromagnet with Neel temperature, T N , of 180 K. The electrical resistivity has an anomaly around T N . Below T N , the magnetoresistance of DyTiGe abruptly changes at a critical field. At 5 K, we observe a magnetoresistance reduction of about 20%

Extending the product variety at ROMAG-PROD Heavy Water Plant

International Nuclear Information System (INIS)

Preda, M.; Patrascu, M.; Achimescu, D.; Stroia, A.

2004-01-01

Full text: Having in mind that the prospects of operating the ROMAG-PROD Heavy Water Plant are conditioned by both the heavy water market demand and the wear of the equipment which is exposed to hydrogen sulfide-induced corrosion, some possibilities were considered to extend the assortment of products, the production of which could ensure the plant's operation on long term. The proposals here refer to promoting the efficient production of oxygen-isotope-based products which would optimize maximally the exploit of available raw materials, supply and utilities of the ROMAG compound. The market manifests a significant demand of water enriched in the 18 O isotope up to 95-97% purity that is used in Positron Emission Tomography (PET). This oxygen isotope is also used as a labelling agent in studies of reaction mechanisms and paleo-climatologic studies as well. Some research evidenced the superconducting properties of some oxygen compounds containing the 18 O isotope. The isotope 17 O has applications in Nuclear Magnetic Resonance (NMR) as being the sole oxygen isotope endowed with a nuclear magnetic moment. On the other hand, it was found that although the 16 O isotope has a natural abundance of 99.8%, applications exist that require the absolute purity of this isotope i.e. the elimination of the other oxygen isotopes as is the case of fission reactors with Plutonium dioxide as nuclear fuel. The methods applied on industrial scale for enriching the oxygen isotopes are based on distillation of some oxygen compounds such as water and nitrogen monoxide. The possibility of a supplementary distillation of the heavy water at a distillation line of ROMAG-PROD Heavy Water Plant was considered in order to enrich the heavy water in the 17 O and 18 O isotopes up to an upper limit of 2-5% for 18 O. Obtaining the heavy isotopes of oxygen by distillation of heavy water is characterized by several aspects as the following ones: a high specific consumption of steam due to both the low

Deuterium and heavy water

International Nuclear Information System (INIS)

Vasaru, G.; Ursu, D.; Mihaila, A.; Szentgyorgyi, P.

1975-01-01

This bibliography on deuterium and heavy water contains 3763 references (1932-1974) from 43 sources of information. An author index and a subject index are given. The latter contains a list of 136 subjects, arranged in 13 main topics: abundance of deuterium , catalysts, catalytic exchange, chemical equilibria, chemical kinetics, deuterium and heavy water analysis, deuterium and heavy water properties, deuterium and heavy water separation, exchange reactions, general review, heavy water as moderator, isotope effects, synthesis of deuterium compounds

Emission spectra of phosphor MgSO4 doped with Dy and Mn

International Nuclear Information System (INIS)

Zhang Chunxiang; Chen Lixin; Tang Qiang; Luo Daling; Qiu Zhiren

2001-01-01

Emission spectra of phosphor MgSO 4 doped with Dy and Dy/Mn were measured with an optical multichannel analyzer and a linear heating system whose temperature was controlled by a microcomputer. The emission spectrum bands at 480 nm and 580 nm of phosphor MgSO 4 doped with Dy were observed in the three dimensional (3D) glow curves. Compared with the 3D spectrum of CaSO 4 :Dy and the spectrum bands of MgSO 4 :Dy shows the same wavelengths which resulted from the quantum transitions among the energy levels of Dy 3 '+ ions. The intensities of the glow peaks in both spectrum bands (480 nm and 580 nm) of phosphor MgSO 4 doped with Dy/Mn were dramatically reduced except the 380 degree C glow peak

Determination of isotopic purity in heavy water to suit process requirement (Preprint No. CA-15)

Energy Technology Data Exchange (ETDEWEB)

Kanthiah, W S.A.; Srinivasan, K; Usuf Ali, M C.M. [Heavy Water Plant, Tuticorin (India)

1989-04-01

In hydrogen/ammonia based heavy water plants, a simple specific gravity determination of heavy water without any purification or thermostating has proved to be simple and easy. The accuracy is found to be well within +- 0.5% in the isotopic purity (I.P) range of 30 to 90% W/W. There are three main methods that can be adopted for determination of I.P in this range: (1)refractometry, (2) infrared spectrophotometry, and (3) pycnometry. Refractrometry requires thermostating and the practical accuracy attainable is +- 1.5% W/W. Infrared spectrophotometer has a reported accuracy/ precision of +- 0.4%. Pycnometric analysis is simple and requires much less expertise and most suited for plant analyses. An accuracy better than +- 0.5% is attained without giving any correction for buoyancy, weighing to accuracy +- 0.1 mg, measuring temperature +- 0.2degC and sample having pH upto 3. (author). 8 annexures.

Relativistic heavy ion experiments at BNL-AGS

International Nuclear Information System (INIS)

Miake, Yasuo

1992-01-01

Relativistic heavy ion program at BNL started in 1986. Already a few experiments have achieved their first goals. Several interesting features reported among which are: The black nuclear transparency, the enhanced K + /π + ratio and the larger t > for K + and proton in central Si+Au collisions. Comparisons of m t and dn/dy distributions between pp, pA and AA are discussed together with various model calculations. (orig.)

Comparison of calculated and experimental values of the yields of xenon isotopes in reactions with high-energy protons

International Nuclear Information System (INIS)

Shukolyukov, A.Yu.; Katargin, N.V.; Baishev, I.S.

1989-01-01

Calculations of the cumulative yields of isotopes of Xe have been carried out on the basis of the semi-empirical formula of Silverberg and Tsao for Ba- and Dy-targets and bombarding proton energies in the range 100-1050 MeV. Results are compared with experimental data for the yields of Xe isotopes, and domains of applicability of the semi-empirical formula are determined

From a Dy(III) single molecule magnet (SMM) to a ferromagnetic [Mn(II)Dy(III)Mn(II)] trinuclear complex.

Science.gov (United States)

Bhunia, Asamanjoy; Gamer, Michael T; Ungur, Liviu; Chibotaru, Liviu F; Powell, Annie K; Lan, Yanhua; Roesky, Peter W; Menges, Fabian; Riehn, Christoph; Niedner-Schatteburg, Gereon

2012-09-17

The Schiff base compound 2,2'-{[(2-aminoethyl)imino]bis[2,1-ethanediyl-nitriloethylidyne]}bis-2-hydroxy-benzoic acid (H(4)L) as a proligand was prepared in situ. This proligand has three potential coordination pockets which make it possible to accommodate from one to three metal ions allowing for the possible formation of mono-, di-, and trinuclear complexes. Reaction of in situ prepared H(4)L with Dy(NO(3))(3)·5H(2)O resulted in the formation of a mononuclear complex [Dy(H(3)L)(2)](NO(3))·(EtOH)·8(H(2)O) (1), which shows SMM behavior. In contrast, reaction of in situ prepared H(4)L with Mn(ClO(4))(2)·6H(2)O and Dy(NO(3))(3)·5H(2)O in the presence of a base resulted in a trinuclear mixed 3d-4f complex (NHEt(3))(2)[Dy{Mn(L)}(2)](ClO(4))·2(H(2)O) (2). At low temperatures, compound 2 is a weak ferromagnet. Thus, the SMM behavior of compound 1 can be switched off by incorporating two Mn(II) ions in close proximity either side of the Dy(III). This quenching behavior is ascribed to the presence of the weak ferromagnetic interactions between the Mn(II) and Dy(III) ions, which at T > 2 K act as a fluctuating field causing the reversal of magnetization on the dysprosium ion. Mass spectrometric ion signals related to compounds 1 and 2 were both detected in positive and negative ion modes via electrospray ionization mass spectrometry. Hydrogen/deuterium exchange (HDX) reactions with ND(3) were performed in a FT-ICR Penning-trap mass spectrometer.

Study of the structure of the transition nuclei 152Dy, 154Dy and 156Er at high angular momentum

International Nuclear Information System (INIS)

Azgui, F.

1985-01-01

Measurements of feeding times of high spin yrast states in 152 Dy, 154 Dy and 156 Er were utilized to obtain information about possible spin dependent shape changes. Feeding times as well as lifetimes were determined with the recoil distance technique. In 152 Dy only long feeding times (> 10 ps) could be identified, indicating that the aligned-particle yrast states are fed through configuration of similar character, with little direct population from collective cascade in the continuum region. In 154 Dy discrete states with I ≤ 30 have lifetimes which are characteristically collective, whereas the preyrast cascade exhibit both fast ( 10 ps) feeding components. The latter imply a change with increasing spin from collective to aligned-particle character, signalling a prolate to oblate shape transition. In 156 Er the yrast states up to spin 20 ℎ were found to be collective. These levels are fed, however, from long-lived high spin states, causing time delay up to ∼ 100 ps, the existence of which is interpreted as a signature for an oblate shape at high spin [fr

Modification of magnetoresistance and magnetic properties of Ni thin films by adding Dy interlayer

Science.gov (United States)

Vorobiov, S. I.; Shabelnyk, T. M.; Shutylieva, O. V.; Pazukha, I. M.; Chornous, A. M.

2018-03-01

The paper reports the influence of dysprosium (Dy) interlayer addition on structure, magnetoresistance and magnetic properties of nickel (Ni) thin films. Trilayer film systems Ni/Dy/Ni have been prepared by alternate electron-beam evaporation. It is demonstrated that all as-prepared and annealed Ni thin films have face-centered cubic structure. The composition of the samples after addition of the Dy interlayer corresponds to the combination of face-centered cubic (Ni) and hexagonal close-packed (Dy) structures. The structure of Ni/Dy/Ni film systems changes from amorphous to polycrystalline when Dy interlayer thickness (t Dy) is more than 15 nm. The value of magnetoresistance increases with the adding the Dy interlayer in both longitudinal and transverse geometries, meanwhile the anisotropic character of magnetoresistance field dependences retained. The saturation and reversal magnetizations are reduced with the increasing of the Dy thickness interlayer, while the coercivity takes the minimum value at t Dy = 15 nm. The following increasing of t Dy leads to increasing of coercivity near to three times. This result indicates the influence of the crystal structure on the magnetic properties of Ni thin films at adding Dy interlayer.

Mechanical and corrosion properties of binary Mg–Dy alloys for medical applications

International Nuclear Information System (INIS)

Yang Lei; Huang Yuanding; Peng Qiuming; Feyerabend, Frank; Kainer, Karl Ulrich; Willumeit, Regine; Hort, Norbert

2011-01-01

Microstructure, mechanical and corrosion properties of binary magnesium–dysprosium (Mg-5, 10, 15, 20 wt.% Dy) alloys were investigated for medical applications. In the as-cast condition, the distribution of Dy is quite inhomogeneous. Mg–10Dy alloy exhibits a moderate tensile and compression yield strength, and the best elongation and corrosion resistance. After T4 (solutionizing) treatment, the distribution of Dy becomes homogeneous. The tensile and compression yield strength of all Mg–Dy alloys decreases. The elongation remains unchanged, while the corrosion resistance is largely improved after T4 treatment.

Mechanical and corrosion properties of binary Mg-Dy alloys for medical applications

Energy Technology Data Exchange (ETDEWEB)

Yang Lei, E-mail: lei.yang@hzg.de [Helmholtz-Zentrum Geesthacht, Institute of Materials Research, Max-Planck-Str. 1, D-21502 Geesthacht (Germany); Yuanding, Huang; Qiuming, Peng; Feyerabend, Frank; Kainer, Karl Ulrich; Willumeit, Regine; Hort, Norbert [Helmholtz-Zentrum Geesthacht, Institute of Materials Research, Max-Planck-Str. 1, D-21502 Geesthacht (Germany)

2011-12-15

Microstructure, mechanical and corrosion properties of binary magnesium-dysprosium (Mg-5, 10, 15, 20 wt.% Dy) alloys were investigated for medical applications. In the as-cast condition, the distribution of Dy is quite inhomogeneous. Mg-10Dy alloy exhibits a moderate tensile and compression yield strength, and the best elongation and corrosion resistance. After T4 (solutionizing) treatment, the distribution of Dy becomes homogeneous. The tensile and compression yield strength of all Mg-Dy alloys decreases. The elongation remains unchanged, while the corrosion resistance is largely improved after T4 treatment.

Techniques for preparing isotopic targets

International Nuclear Information System (INIS)

Xu Guoji; Guan Shouren; Luo Xinghua; Sun Shuhua

1987-12-01

The techniques of making isotopic targets for nuclear physics experiments are introduced. Vacuum evaporation, electroplating, centrifugal precipitation, rolling and focused heavy-ion beam sputtering used to prepare various isotopic targets at IAE are described. Reduction-distillation with active metals and electrolytic reduction for converting isotope oxides to metals are mentioned. The stripping processes of producing self-supporting isotopic targets are summarized. The store methods of metallic targets are given

Dynamic response of the high flux isotope reactor structure caused by nearby heavy load drop

International Nuclear Information System (INIS)

Chang, Shih-Jung.

1995-01-01

A heavy load of 50,000 lb is assumed to drop from 10 ft above the bottom of the High Flux Isotope Reactor (HFIR) pool at the loading station. The consequences of the dynamic impact to the bottom slab of the pool and to the nearby HFIR reactor vessel are analyzed by applying the ABAQUS computer code The results show that both the BM vessel structure and its supporting legs are subjected to elastic disturbances only and, therefore, will not be damaged. The bottom slab of the pool, however, will be damaged to about half of the slab thickness. The velocity response spectrum at the concrete floor next to the HFIR vessel as a result of the vibration caused by the impact is obtained. It is concluded, that the damage caused by heavy load drop at the loading station is controlled by the slab damage and the nearby HFIR vessel and the supporting legs will not be damaged

Determination of isotopic purity in heavy water to suit process requirement (Preprint No. CA-15)

International Nuclear Information System (INIS)

Kanthiah, W.S.A.; Srinivasan, K.; Usuf Ali, M.C.M.

1989-04-01

In hydrogen/ammonia based heavy water plants, a simple specific gravity determination of heavy water without any purification or thermostating has proved to be simple and easy. The accuracy is found to be well within ± 0.5% in the isotopic purity (I.P) range of 30 to 90% W/W. There are three main methods that can be adopted for determination of I.P in this range: (1)refractometry, (2) infrared spectrophotometry, and (3) pycnometry. Refractrometry requires thermostating and the practical accuracy attainable is ± 1.5% W/W. Infrared spectrophotometer has a reported accuracy/ precision of ± 0.4%. Pycnometric analysis is simple and requires much less expertise and most suited for plant analyses. An accuracy better than ± 0.5% is attained without giving any correction for buoyancy, weighing to accuracy ± 0.1 mg, measuring temperature ± 0.2degC and sample having pH upto 3. (author). 8 annexures

Co-precipitation synthesis of YAG:Dy nanophosphor and its thermometric properties

International Nuclear Information System (INIS)

Chong, Joo-Yun; Zhang, Yuelan; Wagner, Brent K.; Kang, Zhitao

2013-01-01

Highlights: •YAG:Dy nanophosphors were synthesized with particle size of about 50 nm. •Optimized doping concentration of 6%Dy was determined. •Thermometric photoluminescence properties were studied between 20 and 350 °C. •Temperature-sensitive change in peak ratio of 496/457 nm emissions was demonstrated. •Suitable for potential thermographic applications when dispersed in a liquid media. -- Abstract: Dy 3+ doped yttrium aluminum garnet (YAG) nanophosphors were synthesized by a co-precipitation method for potential thermographic applications in a liquid media dispersed with fluorescent nanoparticles. The doping concentration and annealing temperature on the structural and optical properties of YAG:Dy were investigated. Pure phase YAG:Dy nanophosphors were obtained by annealing the co-precipitated hydroxide products at above 900 °C. Maximum photoluminescence intensity was observed from 6%Dy doped YAG samples. The effect of measuring temperature between 20 and 350 °C on the photoluminescence spectra of nano YAG:Dy was investigated. A temperature-sensitive change in the peak intensity ratio of 496/457 nm emission lines was demonstrated for such nanophosphors for the first time, suggesting potential applications in temperature monitoring of fuel spray

Co-precipitation synthesis of YAG:Dy nanophosphor and its thermometric properties

Energy Technology Data Exchange (ETDEWEB)

Chong, Joo-Yun [School of Chemical and Biomolecular Engineering, Georgia Institute of Technology, Atlanta, GA 30332 (United States); Zhang, Yuelan [School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332 (United States); Wagner, Brent K. [Georgia Tech Research Institute, Georgia Institute of Technology, Atlanta, GA 30332 (United States); Kang, Zhitao, E-mail: zhitao.kang@gtri.gatech.edu [Georgia Tech Research Institute, Georgia Institute of Technology, Atlanta, GA 30332 (United States); School of Materials Science and Engineering, Georgia Institute of Technology, Atlanta, GA 30332 (United States)

2013-12-25

Highlights: •YAG:Dy nanophosphors were synthesized with particle size of about 50 nm. •Optimized doping concentration of 6%Dy was determined. •Thermometric photoluminescence properties were studied between 20 and 350 °C. •Temperature-sensitive change in peak ratio of 496/457 nm emissions was demonstrated. •Suitable for potential thermographic applications when dispersed in a liquid media. -- Abstract: Dy{sup 3+} doped yttrium aluminum garnet (YAG) nanophosphors were synthesized by a co-precipitation method for potential thermographic applications in a liquid media dispersed with fluorescent nanoparticles. The doping concentration and annealing temperature on the structural and optical properties of YAG:Dy were investigated. Pure phase YAG:Dy nanophosphors were obtained by annealing the co-precipitated hydroxide products at above 900 °C. Maximum photoluminescence intensity was observed from 6%Dy doped YAG samples. The effect of measuring temperature between 20 and 350 °C on the photoluminescence spectra of nano YAG:Dy was investigated. A temperature-sensitive change in the peak intensity ratio of 496/457 nm emission lines was demonstrated for such nanophosphors for the first time, suggesting potential applications in temperature monitoring of fuel spray.

Dy:Eu doped CaBAl glasses for white light applications

Science.gov (United States)

Lodi, T. A.; Sandrini, M.; Medina, A. N.; Barboza, M. J.; Pedrochi, F.; Steimacher, A.

2018-02-01

The combination of Eu3+ and Dy3+ in co-doped glassy materials provides interesting applicability for white light emission devices. In this work, Dy:Eu doped Calcium Boroaluminate (CaBAl) glasses were prepared by conventional melting quenching, with 3 wt% of Dy2O3 and Eu2O3 content varying from 0 to 3 wt%, and results of absorption spectra, photoluminescence and photoluminescence lifetime are discussed in terms of Eu2O3 content. The photoluminescence of the samples was studied under excitation of 365 and 405 nm light source. The 365 nm excitation shows favor to the Dy3+ ion emission. The results of photoluminescence lifetime at 575 nm (Dy3+) shows a decrease due to Eu2O3 addition, which suggests an energy transfer from Dy3+ (donor) to the Eu3+ (acceptor). On the other hand, under excitation of 405 nm, the photoluminescence lifetime at 575 nm (Dy3+) shows no significant changes due to Eu2O3 amount, which indicates that the energy transfer from Dy3+ to Eu3+ (under λexc = 405 nm) is negligible. However, the results of photoluminescence under 405 nm excitation present a white yellowish emission in the CIE diagram, which shifts to red with Eu2O3 addition. The combination of a Blue LED (BL) emission with the emission of the samples was also studied in the CIE diagram, in order to improve light emission and to obtain ideal White Light (WL). The results show that by modifying the emission intensity of BL, it is possible to achieve a route for smart lighting, close to the circadian light cycle.

Search for excited superdeformed bands in {sup 151}Dy

Energy Technology Data Exchange (ETDEWEB)

Nisius, D.; Janssens, R.V.F.; Crowell, B. [and others

1995-08-01

Following the first report of superdeformed (SD) bands with identical transition energies in the pairs ({sup 151}Tb*,{sup 152}Dy), ({sup 150}Gd*, {sup 151}Tb) and ({sup 153}Dy*, {sup 152}Dy) (where * denotes an excited SD band), it was proposed by Nazarewicz et al. that the observations could be understood in a strong-coupling approach if pseudo SU(3) symmetry were invoked. In this model there are three limiting values of the decoupling parameter; i.e. a = 0, {plus_minus}1. In the first two cases mentioned above the pairs of bands have nearly identical transition energies and are interpreted as proton excitations involving the [200]1/2 pseudospin orbital coupled to the {sup 152}Dy core, for which the value of the decoupling parameter is calculated to be a =+1.

Measurement of the purity of graphite and heavy water; Controle de purete du graphite et de l'eau lourde

Energy Technology Data Exchange (ETDEWEB)

Hering, H

1959-02-01

The analytical methods used by the C.E.A. are described, I -- Graphite. The determination of the change in the neutron capture cross section from sample to sample is determined by, an oscillation method in the Zoe reactor, or by measuring the attenuation of a neutron flux in the subcritical system Mireille. Methods of analysing total ash, B, H, Cl, Na, Ca. Fe, Mo, Ti, V, Sm, Eu, Dy, S, Co and Cd are described and mean results are given. The methods for sampling are indicated. II -- Heavy crater. The isotopic analysis of heavy water is carried out by infra-red absorption measurements. Chemical purity is evaluated by electrical conductivity measurements, B, Na, Mg, K, Cr, Mn, Ni, Cu, Cd, are determined by spectrographic methods, and Cl{sup -}, NO{sub 3}{sup -}, SO{sub 4}{sup --}, NH{sub 4}{sup +} by chemical methods; finally, sensitive pH measurements are described. [French] On decrit les methodes d'examen en usage au Commissariat a l'Energie Atomique. I -- Graphite. L'evaluation de la capture neutronique se fait par oscillation dans la pile Zoe, ou par mesure de l'attenuation d'un flux neutronique dans l'empilement sous critique Mireille. On indique les methodes de dosages et des resultats de: cendres, B, H, Cl, Na, Ca, Fe, Mo, Ti, V, Sm, Eu, Dy, et de S, Co, Cd, ainsi que les modalites d'echantillonnage. II.- Eau lourde. Le dosage isotopique dans les eaux lourdes se fait par absorptiometrie infrarouge. Leur purete chimique est evaluee par mesure de leur conductibilite electrique; les dosages d'impuretes se font par spectrographie d'emission (B, Na, Mg, K, Mn, Ni, Cu, Cd) et par des methodes chimiques (Cl{sup -}, NO{sub 3}{sup -}, SO{sub 4}{sup --}, NH{sub 4}{sup +}). On decrit la delicate mesure de pH. (auteur)

Effect of Dy additions on microstructure and magnetic properties of Fe-Nd-B magnets

International Nuclear Information System (INIS)

Ramesh, R.; Thomas, G.; Ma, B.M.

1987-05-01

It is shown that increasing additions of Dy causes the remanence B/sub r/ to decrease linearly. The intrinsic coercivity, iHc, increases sharply for small additions of Dy, but the increase is not proportional for higher Dy contents. The iHc increases almost linearly with the effective anisotropy field of the RE 2 Fe 14 B phase until the Dy content is about 10% of the total rare earth content. Above this concentration, there is strong deviation from linearity. Various types of possible concentration profiles of the substituted rare earth are suggested. It is also argued that preferential segregation of Dy to the interfaces could be beneficial in increasing the nucleation field. Morphologically there is no apparent effect of Dy on the microstructure. However, in the 5 atomic % Dy sample, Dy rich oxides were observed. It is shown through Energy Dispersive Xray Spectroscopy (EDXS) line profiling that Dy partitions preferentially into the RE 2 Fe 14 B phase in all the cases. No segregation of Dy to the interphase interfaces has been detected

Improvement in fuel utilization in pressurized heavy water reactors due to increased heavy water purity

International Nuclear Information System (INIS)

Balakrishnan, M.R.

1991-01-01

This paper reports that in a pressurized heavy water reactor (PHWR), the reactivity of the reactor and, consequently, the discharge burnup of the fuel depend on the isotopic purity of the heavy water used in the reactor. The optimal purity of heavy water used in PHWRs, in turn, depends on the cost of fabricated uranium fuel and on the incremental cost incurred in improving the heavy water purity. The physics and economics aspects of the desirability of increasing the heavy water purity in PHWRs in India were first examined in 1978. With the cost data available at that time, it was found that improving the heavy water purity from 99.80% to 99.95% was economically attractive. The same problem is reinvestigated with current cost data. Even now, there is sufficient incentive to improve the isotopic purity of heavy water used in PHWRs. Admittedly, the economic advantage that can be derived depends on the cost of the fabricated fuel. Nevertheless, irrespective of the economics, there is also a fairly substantial saving in natural uranium. That the increase in the heavy water purity is to be maintained only in the low-pressure moderator system, and not in the high-pressure coolant system, makes the option of achieving higher fuel burnup with higher heavy water purity feasible

Shifts in rotifer life history in response to stable isotope enrichment: testing theories of isotope effects on organismal growth

Science.gov (United States)

2017-01-01

In ecology, stable isotope labelling is commonly used for tracing material transfer in trophic interactions, nutrient budgets and biogeochemical processes. The main assumption in this approach is that the enrichment with a heavy isotope has no effect on the organism growth and metabolism. This assumption is, however, challenged by theoretical considerations and experimental studies on kinetic isotope effects in vivo. Here, I demonstrate profound changes in life histories of the rotifer Brachionus plicatilis fed 15N-enriched algae (0.4–5.0 at%); i.e. at the enrichment levels commonly used in ecological studies. These findings support theoretically predicted effects of heavy isotope enrichment on growth, metabolism and ageing in biological systems and underline the importance of accounting for such effects when using stable isotope labelling in experimental studies. PMID:28405367

DyNi2Mn—magnetisation and Mössbauer spectroscopy

International Nuclear Information System (INIS)

Wang Jianli; Campbell, Stewart James; Kennedy, Shane Joseph; Dou Shixue; Wu Guangheng

2012-01-01

The physical properties of DyNi 2 Mn doped with 57 Fe have been investigated by X-ray diffraction, magnetisation (10–300 K) and 57 Fe Mössbauer spectroscopy measurements (5–300 K). DyNi 2 Mn( 57 Fe) crystallizes in the MgCu 2 -type cubic structure (Fd   −3m space group). The ordering temperature is found to be T C  = 99(2) K, much higher than those of DyNi 2 (∼22 K) and DyMn 2 (∼35 K). Analyses of isothermal M–H curves and the related Arrott plots confirm that the magnetic phase transition at T C is second order. The magnetic entropy change around T C is 4.0 J/kg K for a magnetic field change of 0 T to 5 T. The spectra above T C exhibit features consistent with quadrupolar effects while below T C the spectra exhibit magnetic hyperfine splitting. The Debye temperature for DyNi 2 Mn has been determined as θ D  = 200(20) K from a fit to the variable temperature isomer shift IS(T).

DyNi{sub 2}Mn-magnetisation and Moessbauer spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Wang Jianli; Campbell, Stewart James, E-mail: stewart.campbell@adfa.edu.au [University of New South Wales, School of Physical, Environmental and Mathematical Sciences (Australia); Kennedy, Shane Joseph [ANSTO, Bragg Institute (Australia); Dou Shixue [University of Wollongong, Institute for Superconductivity and Electronic Materials (Australia); Wu Guangheng [Chinese Academy of Science, Institute of Physics (China)

2012-03-15

The physical properties of DyNi{sub 2}Mn doped with {sup 57}Fe have been investigated by X-ray diffraction, magnetisation (10-300 K) and {sup 57}Fe Moessbauer spectroscopy measurements (5-300 K). DyNi{sub 2}Mn({sup 57}Fe) crystallizes in the MgCu{sub 2}-type cubic structure (Fd{sup }-3m space group). The ordering temperature is found to be T{sub C} = 99(2) K, much higher than those of DyNi{sub 2} ({approx}22 K) and DyMn{sub 2} ({approx}35 K). Analyses of isothermal M-H curves and the related Arrott plots confirm that the magnetic phase transition at T{sub C} is second order. The magnetic entropy change around T{sub C} is 4.0 J/kg K for a magnetic field change of 0 T to 5 T. The spectra above T{sub C} exhibit features consistent with quadrupolar effects while below T{sub C} the spectra exhibit magnetic hyperfine splitting. The Debye temperature for DyNi{sub 2}Mn has been determined as {theta}{sub D} = 200(20) K from a fit to the variable temperature isomer shift IS(T).

Production and investigation of tungsten α emitters including the new isotopes, 165W and 166W

International Nuclear Information System (INIS)

Toth, K.S.; Schmidt-Ott, W.; Bingham, C.R.; Ijaz, M.A.

1975-01-01

Neutron-deficient tungsten isotopes were produced by bombarding an enriched 156 Dy target with 16 O ions accelerated in the Oak Ridge isochronous cyclotron. A gas-jet-capillary system was used to transport product nuclei to an area where their α-decay properties could be investigated. The data of Eastham and Grant concerning 162 , 163 , 164 W were confirmed. In addition, two new weak α groups were observed. On the basis of excitation functions, 14 N + 156 Dy cross bombardments, and α-decay energy systematics they were assigned to the new isotopes 165 W and 166 W. Their decay properties are as follows: (1) 165 W, E/sub alpha/ = 4.909 plus-or-minus 0.005 MeV, T 1 / 2 = 5.1 plus-or-minus 0.5 sec, and (2) 166 W, E/sub alpha/ = 4.739 plus-or-minus 0.005 MeV, T 1 / 2 = 16 plus-or-minus 3 sec

Neutron detection using Dy2O3 activation detectors

International Nuclear Information System (INIS)

Gomaa, M.A.; Mohamed, E.J.

1979-01-01

The aim of the present study is to examine the usefulness of Dy 2 O 3 not only as thermal neutron activation detector but also as a fast neutron detector. For thermal neutrons, the half life of 165 Dy is measured to be (141 +- 6) min, its response to thermal neutrons is (2.18 +- 0.01) cpm/ncm -2 s -1 for a 250 mg Dy 2 O 3 pellet. For fast neutrons the Dy 2 O 3 detector is placed within a 20 cm polyethylene sphere and its response is found to be (2.2 +- 0.1) cpm/ncm -2 s -1 for 4 MeV neutrons and (2.10 +- 0.04) cpm/ncm -2 s -1 for 14 MeV neutrons. For neutron dosimetry, its response is found to be (16.7 +- 0.4) cpm per mrem h -1 . (author)

Analytical performance of refractometry in quantitative estimation of isotopic concentration of heavy water in nuclear reactor

International Nuclear Information System (INIS)

Dhole, K.; Ghosh, S.; Datta, A.; Tripathy, M.K.; Bose, H.; Roy, M.; Tyagi, A.K.

2011-01-01

The method of refractometry has been investigated for the quantitative estimation of isotopic concentration of D 2 O (heavy water) in a simulated water sample. Viability of Refractometry as an excellent analytical technique for rapid and non-invasive determination of D 2 O concentration in water samples has been demonstrated. Temperature of the samples was precisely controlled to eliminate effect of temperature fluctuation on refractive index measurement. Calibration performance by this technique exhibited reasonable analytical response over a wide range (1-100%) of D 2 O concentration. (author)

Measurement of mass and isotopic fission yields for heavy fission products with the LOHENGRIN mass spectrometer

International Nuclear Information System (INIS)

Bail, A.

2009-05-01

In spite of the huge amount of fission yield data available in different libraries, more accurate values are still needed for nuclear energy applications and to improve our understanding of the fission process. Thus measurements of fission yields were performed at the mass spectrometer Lohengrin at the Institut Laue-Langevin in Grenoble, France. The mass separator Lohengrin is situated at the research reactor of the institute and permits the placement of an actinide layer in a high thermal neutron flux. It separates fragments according to their atomic mass, kinetic energy and ionic charge state by the action of magnetic and electric fields. Coupled to a high resolution ionization chamber the experiment was used to investigate the mass and isotopic yields of the light mass region. Almost all fission yields of isotopes from Th to Cf have been measured at Lohengrin with this method. To complete and improve the nuclear data libraries, these measurements have been extended in this work to the heavy mass region for the reactions 235 U(n th ,f), 239 Pu(n th ,f) and 241 Pu(n th ,f). For these higher masses an isotopic separation is no longer possible. So, a new method was undertaken with the reaction 239 Pu(n th ,f) to determine the isotopic yields by spectrometry. These experiments have allowed to reduce considerably the uncertainties. Moreover the ionic charge state and kinetic energy distributions were specifically studied and have shown, among others, nanosecond isomers for some masses. (author)

Surface activation of dyed fabric for cellulase treatment.

Science.gov (United States)

Schimper, Christian B; Ibanescu, Constanta; Bechtold, Thomas

2011-10-01

Surface activation of fabric made from cellulose fibres, such as viscose, lyocell, modal fibres and cotton, can be achieved by printing of a concentrated NaOH-containing paste. From the concentration of reducing sugars formed in solution, an increase in intensity of the cellulase hydrolysis by a factor of six to eight was observed, which was mainly concentrated at the activated parts of the fabric surface. This method of local activation is of particular interest for modification of materials that have been dyed with special processes to attain an uneven distribution of dyestuff within the yarn cross-section, e.g., indigo ring-dyed denim yarn for jeans production. Fabrics made from regenerated cellulose fibres were used as model substrate to express the effects of surface activation on indigo-dyed material. Wash-down experiments on indigo-dyed denim demonstrated significant colour removal from the activated surface at low overall weight loss of 4-5%. The method is of relevance for a more eco-friendly processing of jeans in the garment industry. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Studies of normal deformation in {sup 151}Dy

Energy Technology Data Exchange (ETDEWEB)

Nisius, D.; Janssens, R.V.F.; Crowell, B. [and others

1995-08-01

The wealth of data collected in the study of superdeformation in {sup 151}Dy allowed for new information to be obtained on the normally deformed structures in this nucleus. At high spin several new yrast states have been identified for the first time. They were associated with single-particle excitations. Surprisingly, a sequence was identified with energy spacings characteristic of a rotational band of normal ({beta}2 {approximately} 0.2) deformation. The bandhead spin appears to be 15/2{sup -} and the levels extend up to a spin of 87/2{sup -}. A clear backbend is present at intermediate spins. While a similar band based on a bandhead of 6{sup +} is known in {sup 152}Dy, calculations suggest that this collective prolate band should not be seen in {sup 151}Dy. In the experiment described earlier in this report that is aimed at determining the deformations associated with the SD bands in this nucleus and {sup 152}Dy, the deformation associated with this band will be determined. This will provide further insight into the origin of this band.

Laser separation of isotopes of hydrogen

International Nuclear Information System (INIS)

Dave, S.M.; Ghosh, S.K.; Sadhukhan, H.K.

1980-01-01

Laser isotope separation technique is explained and various methods based on the technique are discussed in detail. Requirements of any laser isotope separation method to be acceptable for the production of heavy water are mentioned and economic viability of this process for heavy water production is examined. Investigations carried out to use this technique for deuterium separation using methanol, formaldehyde, propynal, 2,2,-dichloro-1-1-1,-trifluoroethane (Freon 123), polyvinyl chloride and fluoroform-d are reviewed. (M.G.B.)

Enhanced ultraviolet photo-response in Dy doped ZnO thin film

Science.gov (United States)

Kumar, Pawan; Singh, Ranveer; Pandey, Praveen C.

2018-02-01

In the present work, a Dy doped ZnO thin film deposited by the spin coating method has been studied for its potential application in a ZnO based UV detector. The investigations on the structural property and surface morphology of the thin film ensure that the prepared samples are crystalline and exhibit a hexagonal crystal structure of ZnO. A small change in crystallite size has been observed due to Dy doping in ZnO. AFM analysis ascertains the grain growth and smooth surface of the thin films. The Dy doped ZnO thin film exhibits a significant enhancement in UV region absorption as compared to the pure ZnO thin film, which suggests that Dy doped ZnO can be used as a UV detector. Under UV irradiation of wavelength 325 nm, the photocurrent value of Dy doped ZnO is 105.54 μA at 4.5 V, which is 31 times greater than that of the un-doped ZnO thin film (3.39 μA). The calculated value of responsivity is found to increase significantly due to the incorporation of Dy in the ZnO lattice. The observed higher value of photocurrent and responsivity could be attributed to the substitution of Dy in the ZnO lattice, which enhances the conductivity, electron mobility, and defects in ZnO and benefits the UV sensing property.

Radiochemical studies of neutron deficient actinide isotopes

International Nuclear Information System (INIS)

Williams, K.E.

1978-04-01

The production of neutron deficient actinide isotopes in heavy ion reactions was studied using alpha, gamma, x-ray, and spontaneous fission detection systems. A new isotope of berkelium, 242 Bk, was produced with a cross-section of approximately 10 μb in reactions of boron on uranium and nitrogen on thorium. It decays by electron capture with a half-life of 7.0 +- 1.3 minutes. The alpha-branching ratio for this isotope is less than 1% and the spontaneous fission ratio is less than 0.03%. Studies of (Heavy Ion, pxn) and (Heavy Ion, αxn) transfer reactions in comparison with (Heavy ion, xn) compound nucleus reactions revealed transfer reaction cross-sections equal to or greater than the compound nucleus yields. The data show that in some cases the yield of an isotope produced via a (H.I.,pxn) or (H.I.,αxn) reaction may be higher than its production via an xn compound nucleus reaction. These results have dire consequences for proponents of the ''Z 1 + Z 2 = Z/sub 1+2/'' philosophy. It is no longer acceptable to assume that (H.I.,pxn) and (H.I.,αxn) product yields are of no consequence when studying compound nucleus reactions. No evidence for spontaneous fission decay of 228 Pu, 230 Pu, 232 Cm, or 238 Cf was observed indicating that strictly empirical extrapolations of spontaneous fission half-life data is inadequate for predictions of half-lives for unknown neutron deficient actinide isotopes

Production of heavy water by photodesorption

International Nuclear Information System (INIS)

Gangwer, T.; Goldstein, M.K.

1976-01-01

Research has recently brought attention to the laser as a tool for isotope enrichment. So far the main thrust of this effort has been toward uranium enrichment; however, numerous successes in other areas have been demonstrated. Isotopes of boron, sulfur, chlorine, and carbon have been separated. A new technique is proposed for laser isotope enrichment. The technique, referred to as photodesorption, involves selective isotopic excitation of molecules adsorbed on a surface such that an enrichment results from subsequent physical or chemical events undergone by the excited molecules. The specific processes of concern are the physical photodesorption enrichment of heavy water from light water and tritiated water from heavy water. The ability to work directly with water molecules has significant advantages for a commercial process. A photodesorption enrichment process has been forumulated and some analyses have been performed. This process is described and some preliminary cost estimates are made which assume successful accomplishment of the major R and D objectives of the new process. The results indicate that the process has the promise of a significant reduction in the cost of heavy water and that further study is warranted

Sonochemical synthesis of Dy-doped ZnO nanostructures and their photocatalytic properties

Energy Technology Data Exchange (ETDEWEB)

Yayapao, Oranuch [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Thongtem, Titipun, E-mail: ttpthongtem@yahoo.com [Department of Chemistry, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Materials Science Research Center, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Phuruangrat, Anukorn, E-mail: phuruangrat@hotmail.com [Department of Materials Science and Technology, Faculty of Science, Prince of Songkla University, Hat Yai, Songkhla 90112 (Thailand); Thongtem, Somchai [Department of Physics and Materials Science, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand); Materials Science Research Center, Faculty of Science, Chiang Mai University, Chiang Mai 50200 (Thailand)

2013-11-05

Highlights: •Undoped and Dy-doped ZnO used as photocatalysts. •They were synthesized by sonochemistry. •The promising materials for treatment of organic pollutants. -- Abstract: Dy-doped ZnO nanostructures were synthesized by a sonochemical method. The concentration effect of Dy on their phase, morphology, optical properties and photocatalytic activities was investigated. XRD patterns indicated that the as-synthesized 0–3% Dy-doped ZnO was hexagonal wurtzite structure. SEM and TEM show that the products were nanorods with their growth direction along the c axis. The photoluminescence spectrum of 3% Dy-doped ZnO, applied by Gaussian analysis, consists of three emission peaks at 376 nm, 448 nm and 487 nm. The photocatalytic activities of the as-synthesized products were determined from the degradation of methylene blue (C{sub 16}H{sub 18}N{sub 3}SCl) by UV radiation. In this research, the 3% Dy-doped ZnO showed the highest photocatalytic activity.

Sonochemical synthesis of Dy-doped ZnO nanostructures and their photocatalytic properties

International Nuclear Information System (INIS)

Yayapao, Oranuch; Thongtem, Titipun; Phuruangrat, Anukorn; Thongtem, Somchai

2013-01-01

Highlights: •Undoped and Dy-doped ZnO used as photocatalysts. •They were synthesized by sonochemistry. •The promising materials for treatment of organic pollutants. -- Abstract: Dy-doped ZnO nanostructures were synthesized by a sonochemical method. The concentration effect of Dy on their phase, morphology, optical properties and photocatalytic activities was investigated. XRD patterns indicated that the as-synthesized 0–3% Dy-doped ZnO was hexagonal wurtzite structure. SEM and TEM show that the products were nanorods with their growth direction along the c axis. The photoluminescence spectrum of 3% Dy-doped ZnO, applied by Gaussian analysis, consists of three emission peaks at 376 nm, 448 nm and 487 nm. The photocatalytic activities of the as-synthesized products were determined from the degradation of methylene blue (C 16 H 18 N 3 SCl) by UV radiation. In this research, the 3% Dy-doped ZnO showed the highest photocatalytic activity

Determination of the cross section for (n,p) reaction with producing short-lived nuclei on the 162,163Dy isotopes at 13.5 and 14.8 MeV

International Nuclear Information System (INIS)

Luo, Junhua; Feng, Zhifu; An, Li; Jiang, Li; He, Long

2016-01-01

Activation cross-sections for the 162 Dy(n,p) 162 Tb and 163 Dy(n,p) 163 Tb reactions have been measured by means of the activation technique and a coaxial HPGe γ-ray detector at 13.5 and 14.8 MeV. The fast neutrons were produced via the 3 H(d,n) 4 He reaction on Pd-300 neutron generator. The natural high-purity Dy 2 O 3 powder was used as target material. Theoretical excitation functions were calculated using the nuclear-reaction codes EMPIRE-3.2 Malta and TALYS-1.6 with default parameters, at neutron energies varying from the reaction threshold to 20 MeV. The results were also discussed and compared with some corresponding values found in the literature, with the comprehensive evaluation data in ENDF/B-VII.1 and JENDF-4.0 libraries, and with the estimates obtained from a published empirical formula based on the statistical model with Q-value dependence and odd–even effects taken into consideration. - Highlights: • The cross sections for the 162 Dy(n,p) 162 Tb and 163 Dy(n,p) 163 Tb have been measured. • 93 Nb(n,2n) 92m Nb was used as a monitor for neutron fluence. • Codes TALYS-1.6 and EMPIRE-3.2 Malta were used to model the reactions. • The results were compared with previous data. • Inconsistency with previous data and with model calculations are noted.

Isotope ratio measurements with multiple collection inductively coupled plasma mass spectrometry

International Nuclear Information System (INIS)

Platzner, I.T.; Segal, I.; Halicz, L.

2003-01-01

In the studies summarized in this review, it has been shown that IRM of lead in silicates can be carried out without lead separation and purification. Because of time independent mass discrimination and lack of chemical interaction at high plasma temperatures, simple interference corrections are feasible. This data further support the observation that MC-ICP-MS provides data with superior precision comparing to TIMS. Furthermore, it should be noted that the multi collection instrumental configuration exhibits the capability to perform a single IRM with excellent precision and high accuracy for elements with a large number of isotopes. Four of the discussed elements have six (Er) and seven (Dy, Yb, Os) isotopes

Search for neutrinoless double-electron capture of 156Dy

Science.gov (United States)

Finch, S. W.; Tornow, W.

2015-12-01

Background: Multiple large collaborations are currently searching for neutrinoless double-β decay, with the ultimate goal of differentiating the Majorana-Dirac nature of the neutrino. Purpose: Investigate the feasibility of resonant neutrinoless double-electron capture, an experimental alternative to neutrinoless double-β decay. Method: Two clover germanium detectors were operated underground in coincidence to search for the de-excitation γ rays of 156Gd following the neutrinoless double-electron capture of 156Dy. 231.95 d of data were collected at the Kimballton underground research facility with a 231.57 mg enriched 156Dy sample. Results: No counts were seen above background and half-life limits are set at O (1016-1018) yr for the various decay modes of 156Dy. Conclusion: Low background spectra were efficiently collected in the search for neutrinoless double-electron capture of 156Dy, although the low natural abundance and associated lack of large quantities of enriched samples hinders the experimental reach.

Rate-controlling two-proton transfer coupled with heavy-atom motion in the 2-pyridinone-catalyzed mutarotation of tetramethylglucose. Experimental and calculated deuterium isotope effects

International Nuclear Information System (INIS)

Engdahl, K.A.; Bivehed, H.; Ahlberg, P.; Saunders, W.H. Jr.

1983-01-01

Primary and secondary deuterium isotope effects have been measured by polarimetry, and primary isotope effects have been calculated for the classical bifunctional catalysis: 2-pyridinone-catalyzed mutarotation of 2,3,4,6-tetra-O-methyl-α-D-glucopyranose (α-TMG) in benzene. From the positively curved plot of the specific rate of epimerization vs. the mole fraction of 2 H in the ''pool'' of OH and NH hydrogens, the isotope effects k/sub HH//k/sub DD/ = 3.66 +/- 0.09, k/sub HH//k/sub DH/ = 1.5, and k/sub HH//k/sub HD/ = 2.4 have been calculated. A secondary isotope effect of 1.14 +/- 0.02 has been measured by using α-TMG and (1- 2 H)-2,3,4,6-tetra-O-methyl-α-D-glucopyranose [(l- 2 H)-α-TMG], the synthesis of which is described in detail, together with those for (N- 2 H)-2-pyridinone and (1-O- 2 H)-2,3,4,6-tetra-O-methyl-α-D-glucopyranose [(1-O- 2 H)-α-TMG]. The rate data obtained have also been analyzed by fractionation theory, yielding approximately equal fractionation factors (0.5). The interpretation of the results has been assisted by calculations of the primary deuterium isotope effects using the BEBOVIB IV program. Two models involving small and considerable coupling, respectively, of the transferring protons to heavy-atom motion have been considered. In the favored structure for the transition state of the rate-limiting step, two protons are in transit, and their motion is governed either by a potential with a barrier or by one without. Their motion is considerably coupled to the heavy-atom motion (i.e., the breakage of the ring C-O bond), and tunnel corrections to the isotope effects are found to be negligible

Magnetic Properties of Dy in Pb2Sr2DyCu3O8

International Nuclear Information System (INIS)

Skanthakumar, S.; Soderholm, L.; Movshovich, R.

1999-01-01

Superconductivity can be induced at high temperatures in Pb 2 Sr 2 RCu 3 O 8 (R - rare earth) by partially doping Ca 2+ for R 3+ . In order to understand the interplay between magnetism and superconductivity, the magnetic properties of the parent compounds, Pb 2 Sr 2 RCu 3 O 8 , have been studied. The work presented here includes magnetic susceptibility and specific heat measurements on R=Dy and extends the previous studies on R=Ce, Pr, Tb, Ho and Er. Specific heat experiments suggest that the Dy ions order antiferromagnetically with an ordering temperature of 1.3K. The magnetic susceptibility data are in good agreement with the susceptibility calculated using crystal field parameters that are extrapolated from previous modeling of the R=Er and Ho analogs of this series

Transfer products from the reactions of heavy ions with heavy nuclei

International Nuclear Information System (INIS)

Thomas, K.E. III.

1979-11-01

Production of nuclides heavier than the target from 86 Kr- and 136 Xe-induced reactions with 181 Ta and 238 U was investigated. Attempts were made to produce new neutron-excess Np and Pu isotopes by the deep inelastic mechanism. No evidence was found for 242 Np or 247 Pu. Estimates were made for the production of 242 Np, 247 Pu, and 248 Am from heavy-ion reactions with uranium targets. Comparisons of reactions of 86 Kr and 136 Xe ions with thick 181 Ta targets and 86 Kr, 136 Xe and 238 U ions with thick 238 U targets indicate that the most probable products are not dependent on the projectile. The most probable products can be predicted by the equation Z - Z/sub target/ = 0.43 (A - A/sub target/) + 1.0. The major effect of the projectile is the magnitude of the production cross section of the heavy products. Based on these results, estimates are made of the most probable mass of element 114 produced from heavy-ion reactions with 248 Cm and 254 Es targets. These estimates give the mass number of element 114 as approx. 287 if produced in heavy-ion reactions with these very heavy targets. Excitation functions of gold and bismuth isotopes arising from 86 Kr- and 136 Xe-induced reactions with thin 181 Ta targets were measured. These results indicate that the shape and location (in Z and A above the target) of the isotopic distributions are not strongly dependent on the projectile incident energy. Also, the nuclidic cross sections are found to increase with an increase in projectile energy to a maximum at approximately 1.4 to 1.5 times the Coulomb barrier. Above this maximum, the nuclidic cross sections are found to decrease with an increase in projectile energy. This decrease in cross section is believed to be due to fission of the heavy products caused by high excitation energy and angular momentum. 111 references, 39 figures, 34 tables

Flood of new isotopes offers keys to stellar evolution

International Nuclear Information System (INIS)

Normile, D.

1996-01-01

Germany's heavy-ion accelerator laboratory, GSI, is renowned for giving researchers the tools needed to create the six heaviest elements in the periodic table. But the facility is also helping scientist fill gaps at an unprecedented rate in another important atomic listing - a chart of unstable isotopes. Measuring the mass and lifetimes of those isotopes, in turn, could help scientist confirm theories about how supernovae produce heavy elements and distribute them throughout the universe. This article describes both the research process and some of the isotopes

Influence of throttling of the heavy fraction on the uranium isotope separation in the separation nozzle

International Nuclear Information System (INIS)

Bley, P.; Ehrfeld, W.; Heiden, U.

1978-04-01

In a separation nozzle cascade for enrichment of U-235 the cut of the separation elements is adjusted by throttling the heavy fraction. This control process influences directly the flow properties in the nozzle and may noticeably change its separation characteristics. This paper deals with an experimental investigation of the throttling effect on the separation and control characteristics of the separation nozzle operated with a H 2 /UF 6 mixture. In consideration of the extremely small characteristic dimensions of commercial separation nozzle elements the influence of manufacturing tolerances on the characteristics of the throttled nozzle was analysed in detail. It appears, that the elementary effect of isotope separation increases by throttling of the heavy fraction up to 5% without changing the optimum operating conditions. This increase of the elementary effect is not only obtained for separation nozzles with zero tolerances but also for separation nozzles having finite tolerances of the skimmer position. Tolerances of the nozzle width, however, become increasingly detrimental, when the heavy fraction is throttled. Regarding the control characteristics of the separation nozzle it was found out, that the UF 6 -cut of the throttled nozzle reacts more sensitively to alterations of the operating pressures and less sensitively to alterations of the UF 6 -concentration of the process gas mixture. (orig.) [de

Fabrication, magnetostriction properties and applications of Tb-Dy-Fe alloys: a review

Directory of Open Access Journals (Sweden)

Nai-juan Wang

2016-03-01

Full Text Available As an excellent giant-magnetostrictive material, Tb-Dy-Fe alloys (based on Tb0.27-0.30Dy0.73-0.70Fe1.9-2 Laves compound can be applied in many engineering fields, such as sonar transducer systems, sensors, and micro-actuators. However, the cost of the rare earth elements Tb and Dy is too high to be widely applied for the materials. Nowadays, there are two different ways to substitute for these alloying elements. One is to partially replace Tb or Dy by cheaper rare earth elements, such as Pr, Nd, Sm and Ho; and the other is to use non-rare earth elements, such as Co, Al, Mn, Si, Ce, B, Be and C, to substitute Fe to form single MgCu2-type Laves phase and a certain amount of Re-rich phase, which can reduce the brittleness and improve the corrosion resistance of the alloy. This paper systemically introduces the development, the fabrication methods and the corresponding preferred growth directions of Tb-Dy-Fe alloys. In addition, the effects of alloying elements and heat treatment on magnetostrictive and mechanical properties of Tb-Dy-Fe alloys are also reviewed, respectively. Finally, some possible applications of Tb-Dy-Fe alloys are presented.

Physical and optical properties of lithium borosilicate glasses doped with Dy3+ ions

Science.gov (United States)

Ramteke, D. D.; Gedam, R. S.; Swart, H. C.

2018-04-01

The borosilicate glasses with Dy3+ ions were prepared by the melt quench technique with varying concentration of Dy2O3. The glasses were characterized by the density calculation, absorbance and photoluminescence (PL) spectroscopy measurements. Density and molar volume of the glasses increases with increase in Dy3+ ions in the glass matrix. This behavior is correlated with the higher molecular weight and larger ionic radius of Dy3+ ion compared to the other constituents of glass matrix. Emission of Dy3+ doped glasses showed three bands at 482, 573 and at 665 nm which correspond to 6H15/2 (blue), 6H13/2 (yellow) and 6H11/2 (red) transitions. The emission spectra of glasses with different concentration of Dy3+ ions shows that, glasses with 0.5 mol% of Dy2O3 shows highest emission and decreases with further doping. CIE 1931 chromaticity diagram showed that the emission of these glasses was in the white region. Photographs of these glasses under 349 nm Light emitting diode excitation also confirmed the white light emission from these glasses.

Coercivity enhancement in Nd-Fe-B sintered permanent magnet by Dy nanoparticles doping

Energy Technology Data Exchange (ETDEWEB)

Liu, W.Q., E-mail: liuweiqiang77@hotmail.co [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China); Sun, H. [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China); Yi, X.F. [Anhui Earth-panda Advance Magnetic Material Co., Ltd., Anhui 231500 (China); Liu, X.C.; Zhang, D.T. [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China); Yue, M., E-mail: yueming@bjut.edu.c [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China); Zhang, J.X. [College of Materials Science and Engineering, Beijing University of Technology, Beijing 100124 (China)

2010-07-02

Nd-Fe-B permanent magnets with a small amount of Dysprosium (Dy) nanoparticles doping were prepared by conventional sintered method, and the microstructure and magnetic properties of the magnets were studied. Investigation shows that the coercivity rises gradually, while the remanence decreases simultaneously with increased Dy doping amount. As a result, the magnet with 1.5 wt.% Dy exhibits optimal magnetic properties. Further investigation presumed that Dy is enriched as (Nd, Dy){sub 2}Fe{sub 14}B phase in the surface region of the Nd{sub 2}Fe{sub 14}B matrix grains indicated by the enhancement of the magneto-crystalline anisotropy field of the Nd{sub 2}Fe{sub 14}B phase. As a result, the magnet doped with a small amount of Dy nanoparticles possesses remarkably enhanced coercivity without sacrificing its magnetization noticeably.

Evaluation of the exchange interaction and crystal fields in a prototype Dy2 SMM

Science.gov (United States)

Zhang, Qing; Sarachik, Myriam; Baker, Michael; Chen, Yizhang; Kent, Andrew; Pineda, Eufemio; McInnes, Eric

In order to gain an understanding of the INS and magnetization data obtained for Dy2, the simplest member of a newly synthesized family of dysprosium-based molecular magnets, we report on calculations of the magnetic behavior of a Dy2 cluster with the formula [hqH2][Dy2(hq)4(NO3)3].MeOH. The molecular complex contains one high symmetry Dy(III) ion and one low symmetry Dy(III) ion. Our calculations suggest that exchange coupling between the two ions controls the behavior of the magnetization at low temperature, while the crystal field of the low symmetry Dy(III) ion controls the behavior at higher temperature. A point charge electrostatic model, based on crystallographic coordinates, provides a starting point for the determination of the crystal field. Parameters in these calculations are adjusted to provide best fits to inelastic neutron scattering data (INS) and low temperature magnetometry: the INS measurements access crystal field energies and low temperature magnetization probes the Dy-Dy exchange interaction. Work supported by ARO W911NF-13-1-1025 (CCNY) and NSF-DMR-1309202 (NYU).

Luminescent properties in films of ZrO{sub 2}: Dy; Propiedades luminiscentes en peliculas de ZrO{sub 2}: Dy

Energy Technology Data Exchange (ETDEWEB)

Martinez, R. C.; Guzman, J.; Rivera, T.; Ceron, P.; Montes, E.; Guzman, D. [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Unidad Legaria, Av. Legaria No. 694, Col. Irrigacion, 11500 Mexico D. F. (Mexico); Garcia H, M. [UNAM, Instituto de Investigaciones en Materiales, Circuito Exterior, Ciudad Universitaria, 04510 Mexico D. F. (Mexico); Falcony, C. [IPN, Centro de Investigacion y de Estudios Avanzados, Apdo. Postal 14-740, 07000 Mexico D. F. (Mexico); Azorin, J., E-mail: rodmarolm@yahoo.com [Universidad Autonoma Metropolitana, Unidad Iztapala, Av. San Rafael Atlixco 186, 09340 Mexico D. F. (Mexico)

2014-08-15

In this work the luminescent characterization of zirconium oxide (ZrO{sub 2}) films impure with dysprosium (Dy{sup +3}) is reported, obtained by means of the ultrasonics spray pyrolysis technique. The films were deposited on glass substrates (Corning), in a temperatures interval of 400 to 550 grades C, using as precursor elements Zirconium oxide chloride octahydrate (ZrOCl{sub 2}·8H{sub 2}O) and Dysprosium tri-chloride (DyCl{sub 3}), dissolved in deionized water, varying the concentration of the contaminated from the 1 to 20 atomic % with relationship to the zirconium in solution. The luminescent characterization was analyzed by means of photoluminescence and thermoluminescence. The photoluminescence results showed a spectrum with three maxima which correspond to the electronic transitions {sup 4}F{sub 9/2} - {sup 6}H{sub 15/2}, {sup 4}F{sub 9/2} - {sup 6}H{sub 13/2} and {sup 4}F{sub 9/2} - {sup 6}H{sub 11/2} characteristics of the Dy{sup 3+} ion. The thermoluminescence (Tl) response when being exposed to a monochrome UV beam in 240 nm showed a wide curve that exhibits a maxim centered in 200 grades C. The Tl response of ZrO{sub 2}:Dy in function of the dose was shown lineal in the interval of 24 mJ/cm{sup 2} to 432 mJ/cm{sup 2}. A study of the repeatability and dissipation of the ZrO{sub 2}:Dy Tl response is included. Considering the shown previous results we can conclude that the ZrO{sub 2} in film form obtained by spray pyrolysis has luminescent properties in 240 nm. (Author)

Optimization of the operational parameters in isotopic exchange installations. ROMAG PROD plant production of heavy water for the nuclear power plant

International Nuclear Information System (INIS)

Pop, A.

2002-01-01

The ROMAG PROD heavy water plant at Drobeta Turnu Severin together with SN Nuclearelectrica Company and Nuclear Fuel Plant at Pitesti are the most important pillars the National Nuclear Program is based on. The plant became operational on 17th July 1988, was later modernized and now reached in the field a leading position known world wide. There are described the modifications adopted to the two stages of the isotopic exchange installation besides some refurbishment measures of general character. The increase of discharge flow rate in cool columns vs hot columns resulted in a rise of technological regime stability and the feeding rate. Also in the first stage the stripping vapor injection in the hot columns was modified to avoid vacuum excursion in the columns. In the second stage two isotopic exchange trays were replaced with dry trays to obtain drop separation at the cool column top. All the trays from the isotopic exchange section of the cool column were replaced by trays from the hot column. The thermal exchange zone in the cool column was modified by introducing trays with number of holes. The gas flow rate of the stage two compressor was adapted to the design requirements. By these changes of the parameters in the original design were substantially improved, the operation became easier, more secure and safer for the environment while the production of the heavy water doubled between 1995 and 2001 reaching a value of 163 t/y in 2001

Thermoluminescent properties of CaSO4:Dy prepared by precipitation method

International Nuclear Information System (INIS)

Roman, J.; Rivera, T.; Azorin, J.

2009-10-01

This paper reports the synthesis and thermoluminescent (Tl) characterization of CaSO 4 :Dy obtained by the precipitation method. Thermoluminescent CaSO 4 :Dy powder and Teflon (PTFE) were mixed in order to obtain samples in pellets form. Samples of CaSO 4 :Dy were exposed to a radiation gamma source of 60 Co and 90 Sr beta particles. Tl response of CaSO 4 :Dy showed a glow curve with two peaks centered at around 164 and 302 C. Tl phosphor showed a good linearity in the range from 0.5 to 30 Gy. Fading of the Tl information was 5.19 % in 37 days and presented a standard deviation of 4% for reproducibility. (Author)

Chromium isotope variations

DEFF Research Database (Denmark)

D'Arcy, Joan Mary

the δ53Cr value of continental runoff into the ocean. The major findings were that river water is characterised by heavy δ53Cr values (+0.1‰ to +1.6‰), while soils are characterised by light δ53Cr values (-0.3‰), relative to the catchment bedrock (-0.17‰ to -0.21‰), indicating that Cr isotopes......, and the quantification the Cr isotope composition of major Cr fluxes into and out of ocean. This thesis adds to the current knowledge of the Cr isotope system and is divided into two studies. The focus of the first study was to determine what processes control the Cr isotopic compositionof river water and to quantify......Chromium (Cr) stable isotopes are a useful tracer of changes in redox conditions because changes in its oxidation state are accompanied by an isotopic fractionation. For this reason the Cr isotope system is being developed as a potential tool for paleo-redox reconstruction. Dissolved Cr in seawater...

The study on production of CaSO4 (Dy) dosimeters

International Nuclear Information System (INIS)

Sriratchatchaval, V.

1989-05-01

The purpose of this experiment is to find out the techniques of preparation and production and to study the characteristic of Thermoluminescence Dosimeter (TLD); CaSO 4 (Dy). This dosimeter is produced as pellets with 1.0 mm thickness and diameter 4.8 mm, which is suitable for gamma rays and X-rays detector. CeSO 4 (Dy) is prepared by adding Dy 2 O 3 (0.2 mole %Dy) to CaSO 4 .2H 2 O then taking this mixture to crystallize in conc. H 2 SO 4 at 300 0 C responds linearly to gamma rays in the range of 0.01-100 mGy and gives the highest peak at 205 0 C. This TLD is fading 3% per month, low sensitivity to light and the response of signal depends on the energy level of gamma rays

Radiochemical studies of neutron deficient actinide isotopes

Energy Technology Data Exchange (ETDEWEB)

Williams, K.E.

1978-04-01

The production of neutron deficient actinide isotopes in heavy ion reactions was studied using alpha, gamma, x-ray, and spontaneous fission detection systems. A new isotope of berkelium, /sup 242/Bk, was produced with a cross-section of approximately 10 ..mu..b in reactions of boron on uranium and nitrogen on thorium. It decays by electron capture with a half-life of 7.0 +- 1.3 minutes. The alpha-branching ratio for this isotope is less than 1% and the spontaneous fission ratio is less than 0.03%. Studies of (Heavy Ion, pxn) and (Heavy Ion, ..cap alpha..xn) transfer reactions in comparison with (Heavy ion, xn) compound nucleus reactions revealed transfer reaction cross-sections equal to or greater than the compound nucleus yields. The data show that in some cases the yield of an isotope produced via a (H.I.,pxn) or (H.I.,..cap alpha..xn) reaction may be higher than its production via an xn compound nucleus reaction. These results have dire consequences for proponents of the ''Z/sub 1/ + Z/sub 2/ = Z/sub 1+2/'' philosophy. It is no longer acceptable to assume that (H.I.,pxn) and (H.I.,..cap alpha..xn) product yields are of no consequence when studying compound nucleus reactions. No evidence for spontaneous fission decay of /sup 228/Pu, /sup 230/Pu, /sup 232/Cm, or /sup 238/Cf was observed indicating that strictly empirical extrapolations of spontaneous fission half-life data is inadequate for predictions of half-lives for unknown neutron deficient actinide isotopes.

Magnetostriction of Tb-Dy-Fe crystals

International Nuclear Information System (INIS)

Mei Wu; Okane, T.; Umeda, T.

1998-01-01

left angle 111 right angle -oriented twin free Tb-Dy-Fe single crystals, left angle 112 right angle - and left angle 110 right angle -oriented twinned ''single'' Tb-Dy-Fe crystals were prepared using floating zone melting crystal growth methods. Magnetostrictive performances of the crystals were investigated. Better low-field properties were observed in the left angle 110 right angle twinned crystals than in the left angle 112 right angle crystals. The highest properties were achieved in the left angle 111 right angle twin free single crystals. Even though there were still oxidized particles in the present left angle 111 right angle single crystals, a large magnetostrictive jump of 1700 ppm and a very low saturation magnetic field of 500 Oe were obtained. To understand magnetization and magnetostriction of different Tb-Dy-Fe crystals, theoretical modeling was carried out based on a simplified domain rotation model. Magnetization moment rotation paths of different domains were simulated and hence the resultant magnetostriction was obtained, which could adequately account for the experimental results of different crystals. The limitation of the domain rotation model was also discussed. (orig.)

Low energy methods of molecular laser isotope separation

International Nuclear Information System (INIS)

Makarov, G N

2015-01-01

Of the many proposals to date for laser-assisted isotope separation methods, isotope-selective infrared (IR) multiphoton dissociation (MPD) of molecules has been the most fully developed. This concept served as the basis for the development and operation of the carbon isotope separation facility in Kaliningrad, Russia. The extension of this method to heavy elements, including uranium, is hindered by, among other factors, the high power consumption and the lack of high-efficiency high-power laser systems. In this connection, research and development covering low energy methods for the laser separation of isotopes (including those of heavy atoms) is currently in high demand. This paper reviews approaches to the realization of IR-laser-induced isotope-selective processes, some of which are potentially the basis on which low-energy methods for molecular laser isotope separation can be developed. The basic physics and chemistry, application potential, and strengths and weaknesses of these approaches are discussed. Potentially promising alternatives to the title methods are examined. (reviews of topical problems)

Transition rates in {sup 161}Dy

Energy Technology Data Exchange (ETDEWEB)

Berg, V; Malmskog, S G

1969-06-15

The decay of {sup 161}Tb has been studied using a high resolution Ge(Li)-detector. Five new transitions were observed and fitted into the earlier proposed decay scheme. The half-life of the 131.8 keV level in {sup 161}Dy was determined in a delayed coincidence measurement to be 145 {+-} 15 psec. The low level scheme in {sup 161}Dy is discussed within a quasi-particle model allowing for Coriolis mixing. Special attention is given to the strongly retarded, K-allowed 131.8 keV E1 transition with a retardation factor F{sub W} > 1.5 x 10{sup 8}.

Nuclear structure studies of neutron-rich heavy nuclei by mass measurements of francium and radium isotopes

Energy Technology Data Exchange (ETDEWEB)

Rosenbusch, Marco [Ernst-Moritz-Arndt-Universitaet, Institut fuer Physik, 17487 Greifswald (Germany); Collaboration: ISOLTRAP-Collaboration

2013-07-01

The mass is a unique property of an atomic nucleus reflecting its binding energy and thus the sum of all interactions at work. Precise measurements of nuclear masses especially of short-lived exotic nuclides provide important input for nuclear structure, nuclear astrophysics, tests of the Standard Model, and weak interaction studies. The Penning-trap mass spectrometer ISOLTRAP at the on-line isotope separator ISOLDE/CERN has been set up for precision mass measurements and continuously improved for accessing more exotic nuclides. The mass uncertainty is typically δm / m=10{sup -8} and the accessible half-life has been reduced to about 50 ms. In this contribution, the results of a measurement campaign of neutron-rich francium and radium isotopes will be presented, i.e. the masses of the isotopic chain of {sup 224-233}Fr and {sup 233,234}Ra, one of the most neutron-rich ensemble obtainable at ISOL facilities. The mass {sup 234}Ra denotes the heaviest mass ever measured with ISOLTRAP. Experimental data in the neutron-rich, heavy mass region is of great interest for studies of structural evolution far from stability, especially because the knowledge from nuclear mass models is scarce. The impact of the new data on the physics in this mass region as well as recent technical developments of ISOLTRAP are discussed.

A study of the structure of 162Dy through the (n,γ) and (n,e-) reactions

International Nuclear Information System (INIS)

Warner, D.D.; Shi, Z.R.; Gelletly, W.; Borner, H.G.; Hoyler, F.; Schreckenbach, K.; van Isacker, P.

1987-01-01

The level structure below 2 MeV in 162 Dy has been investigated using the 161 Dy(n,γ) 162 Dy and 161 Dy(n,e - ) 162 Dy reactions. The results for the positive parity excitations are discussed within the framework of an Interacting Boson Approximation (IBA-2) calculation. 7 refs., 1 fig., 1 tab

Transition-state analysis of a Vmax mutant of AMP nucleosidase by the application of heavy-atom kinetic isotope effects

International Nuclear Information System (INIS)

Parkin, D.W.; Mentch, F.; Banks, G.A.; Horenstein, B.A.; Schramm, V.L.

1991-01-01

The transition state of the V max mutant of AMP nucleosidase from Azotobacter vinelandii has been characterized by heavy-atom kinetic isotope effects in the presence and absence of MgATP, the allosteric activator. The enzyme catalyzes hydrolysis of the N-glycosidic bond of AMP at approximately 2% of the rate of the normal enzyme with only minor changes in the K m for substrate, the activation constant for MgATP, and the K i for formycin 5'-phosphate, a tight-binding competitive inhibitor. Isotope effects were measured as a function of the allosteric activator concentration that increases the turnover number of the enzyme from 0.006 s -1 . The kinetic isotope effects were measured with the substrates [1'- 3 H]AMP, [2'- 2 H]AMP, [9- 15 N]AMP, and [1',9- 14 C, 15 N]AMP. All substrates gave significant kinetic isotope effects in a pattern that establishes that the reaction expresses intrinsic kinetic isotope effects in the presence or absence of MgATP. Transition-state analysis using bond-energy and bond-order vibrational analysis indicated that the transition state for the mutant enzyme has a similar position in the reaction coordinate compared to that for the normal enzyme. The mutant enzyme is less effective in stabilizing the carbocation-like intermediate and in the ability to protonate N7 of adenine to create a better leaving group. This altered transition-state structure was confirmed by an altered substrate specificity for the mutant protein

Efficient photoluminescence of Dy3+ at low concentrations in nanocrystalline ZrO2

International Nuclear Information System (INIS)

Diaz-Torres, L.A.; Rosa, E. de la; Salas, P.; Romero, V.H.; Angeles-Chavez, C.

2008-01-01

Nanocrystalline ZrO 2 :Dy 3+ were prepared by sol-gel and the structural and photoluminescence properties characterized. The crystallite size ranges from 20 to 50 nm and the crystalline phase is a mixture of tetragonal and monoclinic structure controlled by dopant concentration. Strong white light produced by the host emission band centered at ∼460 nm and two strong Dy 3+ emission bands, blue (488 nm) and yellow (580 nm), under direct excitation at 350 nm were observed. The highest efficiency was obtained for 0.5 mol% of Dy 3+ . Emission is explained in terms of high asymmetry of the host suggesting that Dy 3+ are substituted mainly into Zr 4+ lattice sites at the crystallite surface. Luminescence quenching is explained in terms of cross-relaxation of intermediate Dy 3+ levels. - Graphical abstract: White light emission from ∼70 nm ZrO 2 :Dy 3+ nanocrystals. The highest efficiency was obtained for 0.5 mol% of dopant and the dominant crystalline structure was monoclinic

Heavy water. A production alternative for Venezuela

International Nuclear Information System (INIS)

A survey of heavy water production methods is made. Main facts about isotopic and distillation methods, reforming and coupling to a Hydrogen distillation plant are presented. A feasibility study on heavy water production in Venezuela is suggested

The momentum-loss achromat - a new method for the isotopical separation of relativistic heavy ions

International Nuclear Information System (INIS)

Schmidt, K.H.; Geissel, H.; Muenzenberg, G.; Dufour, J.P.; Hanelt, E.

1987-03-01

The application of the slowing-down process of relativistic heavy ions in a layer of matter in ion-optical devices is theoretically investigated. The modifications of the phase space of the ion beam due to the dissipative forces and the straggling phenomena are discussed. Methods are developed to study the properties of the momentum-loss achromat, an isotope separator consisting of an achromatic magnetic system with an energy degrader located in the intermediate dispersive focal plane. This device separates projectile fragments with respect to A and Z up to uranium over a wide energy range with an efficiency in the order of 50% and with separation times of several hundred nanoseconds. (orig.)

Procedure and equipment for the separation of isotopes for deuterium upgrading and for the production of heavy water

International Nuclear Information System (INIS)

Schoell, M.

1981-01-01

The invention concerns a simple procedure for the separation of isotopes for the enrichment of deuterium and for the production of heavy water as well as the equipment necessary for carrying out the process. Methane is conducted over bacterial cultures oxidizing methane to water and carbon dioxide. An enrichment of deuterium takes place in non-oxidized methane. The bacterial cultures are placed on carriers that are arranged in oxidation columns as baffle plates. Several oxidation towers of this kind can be arranged in series. (orig./RW) [de

Study of a new magnetic dipole mode in the heavy deformed nuclei 154Sm, 156Gd, 158Gd, 164Dy, 168Er, and 174Yb by high-resolution electron spectroscopy

International Nuclear Information System (INIS)

Bohle, D.

1985-01-01

By inelastic electron scattering with high energy resolution a new magnetic dipole mode in heavy, deformed nuclei could be detected. For this the nuclei 154 Sm, 156 Gd, 158 Gd, 164 Dy, 168 Er, and 174 Yb were studied at the Darmstadt electron linear accelerator (DALINAC) at small momentum transfer q ≤ 0.6 fm -1 and low excitation energies. A collective magnetic dipole excitation could be discovered in all nuclei at an excitation energy of E x ≅ 66 δA -1/3 MeV whereby δ means the mass deformation. The transition strength extends in the mean to B(M1)↑ ≅ 1.3 μ N 2 . A systematic study of the nucleus 156 Gd yielded hints to a strong fragmentation of the magnetic dipole strength. A comparison of electron scattering, proton scattering, and nuclear resonance fluorescence experiments shows that the new mode is a pure orbital mode. (orig./HSI) [de

Kinetic control on Zn isotope signatures recorded in marine diatoms

Science.gov (United States)

Köbberich, Michael; Vance, Derek

2017-08-01

Marine diatoms dominate the oceanic cycle of the essential micronutrient zinc (Zn). The stable isotopes of zinc and other metals are increasingly used to understand trace metal micronutrient cycling in the oceans. One clear feature of the early isotope data is the heavy Zn isotope signature of the average oceanic dissolved pool relative to the inputs, potentially driven by uptake of light isotopes into phytoplankton cells and export to sediments. However, despite the fact that diatoms strip Zn from surface waters across the Antarctic polar front in the Southern Ocean, the local upper ocean is not isotopically heavy. Here we use culturing experiments to quantify the extent of Zn isotope fractionation by diatoms and to elucidate the mechanisms driving it. We have cultured two different open-ocean diatom species (T. oceanica and Chaetoceros sp.) in a series of experiments at constant medium Zn concentration but at bioavailable medium Fe ranging from limiting to replete. We find that T. oceanica can maintain high growth rates and Zn uptake rates over the full range of bioavailable iron (Fe) investigated, and that the Zn taken up has a δ66Zn that is unfractionated relative to that of the bioavailable free Zn in the medium. The studied representative of the genus Chaetoceros, on the other hand, shows more significantly reduced Zn uptake rates at low Fe and records more variable biomass δ66Zn signatures, of up to 0.85‰ heavier than the medium. We interpret the preferential uptake of heavy isotopes at extremely low Zn uptake rates as potentially due to either of the following two mechanisms. First, the release of extracellular polymeric substances (EPS), at low Fe levels, may preferentially scavenge heavy Zn isotopes. Second, the Zn uptake rate may be slow enough to establish pseudo-equilibrium conditions at the transporter site, with heavy Zn isotopes forming more stable surface complexes. Thus we find that, in our experiments, Fe-limitation exerts a key control that

Role of hydrogen in Nd–Fe–B sintered magnets with DyH{sub x} addition

Energy Technology Data Exchange (ETDEWEB)

Liu, Pan [State Key Laboratory of Silicon Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Ma, Tianyu, E-mail: maty@zju.edu.cn [Key Laboratory of Novel Materials for Information Technology of Zhejiang Province, Zhejiang University, Hangzhou 310027 (China); Wang, Xinhua, E-mail: xinhwang@zju.edu.cn [State Key Laboratory of Silicon Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Zhang, Yujing [State Key Laboratory of Silicon Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Yan, Mi [State Key Laboratory of Silicon Materials, Department of Materials Science and Engineering, Zhejiang University, Hangzhou 310027 (China); Key Laboratory of Novel Materials for Information Technology of Zhejiang Province, Zhejiang University, Hangzhou 310027 (China)

2015-04-15

Highlights: • DyH{sub 2} and DyH{sub 3} fine powder were prepared. • Effect of DyH{sub x} on the magnetic properties of Nd–Fe–B sintered magnets was studied. • The effect mechanism of Dy hydrides was discussed. • The magnetic properties are greatly improved by DyH{sub 2} and DyH{sub 3} addition. - Abstract: In order to improve the coercivity of Nd–Fe–B sintered magnets, DyH{sub 2} and DyH{sub 3} fine powders were prepared and used as additive for preparing Nd–Fe–B sintered magnets. The effects of DyH{sub x} powders addition on the microstructures and the magnetic properties of the magnets have been investigated. It was found that hydrogen will react with oxygen of NdO{sub x} rich intergranular phases to form Nd rich phases by dysprosium hydride addition. The Nd-rich grain boundary phases are more homogenous and continuous because the volume fraction of Nd-rich grain boundary phases increases with respect to the Nd oxide phases. After desorption, fine dysprosium powders become more active and wrap matrix phases well so that the diffusion of dysprosium to the surface layer of matrix phases is convenient, so dysprosium decreases in grain boundary phases and aggregates in surface layer of matrix phases. Then, intrinsic coercivity of NdFeB sintered magnets is improved from 14.96 kOe to 20.5 kOe and 20.31 kOe by 2.0 wt.% DyH{sub 3} and 2.0 wt.% DyH{sub 2} addition, respectively. This study has shown that DyH{sub x} addition can reduce the content of oxygen in grain boundary phases. This can be an effective method for massive production.

Isotopic germanium targets for high beam current applications at GAMMASPHERE

International Nuclear Information System (INIS)

Greene, J. P.; Lauritsen, T.

2000-01-01

The creation of a specific heavy ion residue via heavy ion fusion can usually be achieved through a number of beam and target combinations. Sometimes it is necessary to choose combinations with rare beams and/or difficult targets in order to achieve the physics goals of an experiment. A case in point was a recent experiment to produce 152 Dy at very high spins and low excitation energy with detection of the residue in a recoil mass analyzer. Both to create the nucleus cold and with a small recoil-cone so that the efficiency of the mass analyzer would be high, it was necessary to use the 80 Se on 76 Ge reaction rather than the standard 48 Ca on 108 Pd reaction. Because the recoil velocity of the 152 Dy residues was very high using this symmetric reaction (5% v/c), it was furthermore necessary to use a stack of two thin targets to reduce the Doppler broadening. Germanium targets are fragile and do not withstand high beam currents, therefore the 76 Ge target stacks were mounted on a rotating target wheel. A description of the 76 Ge target stack preparation will be presented and the target performance described

The heavy water production plant at Arroyito, Argentina

International Nuclear Information System (INIS)

Ecabert, R.

1984-01-01

The author describes the construction of an industrial heavy water production plant (Planta Industrial de Agua Pesada, PIAP) in Argentina. The heavy water enrichment is based on a hydrogen/ammonia isotope exchange. (Auth.)

Long-lived heavy mass elements half-lives (A > 125)

International Nuclear Information System (INIS)

Holden, N.E.

1985-01-01

Reported values of half-lives of intermediate mass and heavy elements are evaluated. The evaluation analysis estimates the systematic error the resulting standard deviation. Recommended values are then presented for 128 Te, 130 Te, 129 I, 138 La, 144 Nd, 145 Nd, /sup 146,147,148/Sm, 152 Gd, 154 Dy, 176 Lu, 174 Hf, 180 Ta, 187 Re, 186 Os, 190 Pt, /sup 204,205/Pb, and /sup 230,232/Th. 103 refs., 21 tabs

Surface magnetic phase transitions in Dy/Lu superlattices

International Nuclear Information System (INIS)

Goff, J.P.; Sarthour, R.S.; Micheletti, C.; Langridge, S.; Wilkins, C.J.T.; Ward, R.C.C.; Wells, M.R.

1999-01-01

Dy/Lu superlattices comprising ferromagnetic Dy blocks coupled antiferromagnetically across the Lu blocks may be modelled as a chain of XY spins with antiferromagnetic exchange and six-fold anisotropy. We have calculated the stable magnetic phases for the cases of large anisotropy and a field applied along an easy direction. For an infinite chain an intermediate phase (1, 5,...) is predicted, where the notation gives the angle between the moment and the applied field in units of π/3. Furthermore, the effects of surface reconstruction are determined for finite chains. A [Dy 20 Lu 12 ] 20 superlattice has been studied using bulk magnetization and polarized neutron reflectivity. The (1, 5,...) phase has been identified and the results provide direct evidence in support of the theoretical predictions. Dipolar forces are shown to account for the magnitude of the observed exchange coupling. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

[Validity and reliability of the spanish EQ-5D-Y proxy version].

Science.gov (United States)

Gusi, N; Perez-Sousa, M A; Gozalo-Delgado, M; Olivares, P R

2014-10-01

A proxy version of the EQ-5D-Y, a questionnaire to evaluate the Health Related Quality of Life (HRQoL) in children and adolescents, has recently been developed. There are currently no data on the validity and reliability of this tool. The objective of this study was to analyze the validity and reliability of the EQ-5D-Y proxy version. A core set of self-report tools, including the Spanish version of the EQ-5D-Y were administered to a group of Spanish children and adolescents drawn from the general population. A similar core set of internationally standardized proxy tools, including the EQ-5D-Y proxy version were administered to their parents. Test-retest reliability was determined, and correlations with other generic measurements of HRQoL were calculated. Additionally, known group validity was examined by comparing groups with a priori expected differences in HRQoL. The agreement between the self-report and proxy version responses was also calculated. A total of 477 children and adolescents and their parents participated in the study. One week later, 158 participants completed the EQ-5D-Y/EQ-5D-Y proxy to facilitate reliability analysis. Agreement between the test-retest scores was higher than 88% for EQ-5D-Y self-report, and proxy version. Correlations with other health measurements showed similar convergent validity to that observed in the international EQ-5D-Y. Agreement between the self-report and proxy versions ranged from 72.9% to 97.1%. The results provide preliminary evidence of the reliability and validity of the EQ-5D-Y proxy version. Copyright © 2013 Asociación Española de Pediatría. Published by Elsevier Espana. All rights reserved.

Blue–green afterglow of BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors

Energy Technology Data Exchange (ETDEWEB)

Zhai, Bao-gai [School of Mathematics and Physics, Changzhou University, Jiangsu 213164 (China); Ma, Qing-lan [School of Mathematics and Physics, Changzhou University, Jiangsu 213164 (China); School of Electronics and Information, Nantong University, Jiangsu 226019 (China); Xiong, Rui [School of Physics and Technology, Wuhan University, Hubei 430072 (China); Li, Xiazhang [Analysis and Testing Center, Changzhou University, Jiangsu 213164 (China); Huang, Yuan Ming, E-mail: dongshanisland@126.com [School of Mathematics and Physics, Changzhou University, Jiangsu 213164 (China)

2016-03-15

Highlights: • Afterglow can be achieved when Eu{sup 2+} is absent in the DyAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors. • The afterglow of DyAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors is discernible to naked eyes for minutes. • Dy{sup 3+} introduced trap centers are believed to be responsible for the afterglow. - Abstract: Dy{sup 3+} doped barium aluminate (BaAl{sub 2}O{sub 4}:Dy{sup 3+}) phosphors were prepared via the sol–gel combustion route at the ignition temperature of 600 °C. The phosphors were characterized with X-ray diffractometry, scanning electron microscopy, transmission electron microscopy, photoluminescence spectroscopy, Fourier transform infrared spectroscopy and X-ray photoelectron spectroscopy. Regardless of the absence of Eu{sup 2+} luminescent centers, broadband blue–green afterglow with its peak at about 490 nm was recorded in the BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors. The decay profile of the blue–green afterglow can be best fitted into a two-component exponential function with the two lifetime decay constants to be 8.81 and 45.25 s, respectively. The observation of blue–green afterglow from BaAl{sub 2}O{sub 4}:Dy{sup 3+} in the absence of Eu{sup 2+} provides unique opportunity in unveiling the afterglow mechanisms of rare-earth doped alkaline-metal aluminates. Possible mechanisms on the blue–green afterglow in BaAl{sub 2}O{sub 4}:Dy{sup 3+} phosphors are discussed in terms of the Dy{sup 3+} ions introduced trap centers as well as luminescent centers in the crystal lattice.

Development of Thermoluminescence Dosimeter CaSO4:Dy as Personal and Environmental Dosimeters

International Nuclear Information System (INIS)

Hasnel Sofyan

2009-01-01

Development of personal and environmental dosimeters using material phosphors of CaSO 4 :Dy powder in form capillary glass and disc teflon thermoluminescence (TL) dosimeter have been done. TL dosimeter CaSO 4 :Dy powder used can record dose response less than 0.01 mGy. Fading of TL dosimeter capillary glass after 29 days is 25%. In 1 batch, making of CaSO 4 :Dy powder can obtain 2 groups of dosimeter capillaries with coefficient variance smaller than 10%. This discrepancy caused difference in powder making and reading of the TL dosimeter. TL dosimeter CaSO 4 :Dy teflon disc with dia. 5 mm and 0.8 mm thickness is homogeneous mixture between phosphor powder with dia. 80 to 150 mesh and teflon powder dia. 20 μm. The composition of CaSO 4 :Dy and teflon in TL dosimeter influence sensitivity of the dosimeter. It’ concluded that in order to obtain optimal sensitivity of TL dosimeter, the composition of CaSO 4 :Dy and teflon is 3 and 1 with pressured of disc in 700 MPa. (author).

Selective arc-discharge synthesis of Dy2S-clusterfullerenes and their isomer-dependent single molecule magnetism.

Science.gov (United States)

Chen, Chia-Hsiang; Krylov, Denis S; Avdoshenko, Stanislav M; Liu, Fupin; Spree, Lukas; Yadav, Ravi; Alvertis, Antonis; Hozoi, Liviu; Nenkov, Konstantin; Kostanyan, Aram; Greber, Thomas; Wolter, Anja U B; Popov, Alexey A

2017-09-01

A method for the selective synthesis of sulfide clusterfullerenes Dy 2 S@C 2 n is developed. Addition of methane to the reactive atmosphere reduces the formation of empty fullerenes in the arc-discharge synthesis, whereas the use of Dy 2 S 3 as a source of metal and sulfur affords sulfide clusterfullerenes as the main fullerene products along with smaller amounts of carbide clusterfullerenes. Two isomers of Dy 2 S@C 82 with C s (6) and C 3v (8) cage symmetry, Dy 2 S@C 72 - C s (10528), and a carbide clusterfullerene Dy 2 C 2 @C 82 - C s (6) were isolated. The molecular structure of both Dy 2 S@C 82 isomers was elucidated by single-crystal X-ray diffraction. SQUID magnetometry demonstrates that all of these clusterfullerenes exhibit hysteresis of magnetization, with Dy 2 S@C 82 - C 3v (8) being the strongest single molecule magnet in the series. DC- and AC-susceptibility measurements were used to determine magnetization relaxation times in the temperature range from 1.6 K to 70 K. Unprecedented magnetization relaxation dynamics with three consequent Orbach processes and energy barriers of 10.5, 48, and 1232 K are determined for Dy 2 S@C 82 - C 3v (8). Dy 2 S@C 82 - C s (6) exhibits faster relaxation of magnetization with two barriers of 15.2 and 523 K. Ab initio calculations were used to interpret experimental data and compare the Dy-sulfide clusterfullerenes to other Dy-clusterfullerenes. The smallest and largest barriers are ascribed to the exchange/dipolar barrier and relaxation via crystal-field states, respectively, whereas an intermediate energy barrier of 48 K in Dy 2 S@C 82 - C 3v (8) is assigned to the local phonon mode, corresponding to the librational motion of the Dy 2 S cluster inside the carbon cage.

The isolation and the separation of Sm, Gd, Dy by extraction

International Nuclear Information System (INIS)

Biyantoro, D.; Lahagu, F.; Basuki, K.T.; Handini, T.; Rosyidin

1996-01-01

The isolation of yttrium and separation of Sm, Gd, y with extraction has been investigated. The steps of the process include of this research were the production the concentrate of lanthanide, the dilution, the isolation of yttrium, and the separation of the Sm, Gd, Dy. The first step was the digestion of xenotime sand, the extraction, the dilution, the filtration, the precipitation, the baking production a lanthanide oxide. The step was the separation of yttrium, the stripping, and the calcination production of yttrium oxide. And the third process was the separation of Sm, Gd, Dy by extraction process using method liquid-liquid extraction with extractant of D 2 EHPA and a solvent of dodecane. From the result have been found concentration of yttrium oxide = 88,71 %. The optimum condition of the separation of Gd/Dy have been found : the concentration of HNO 3 = 0,5 M, time of extraction = 15 minutes, and the concentration of extractant = 30 % D 2 EHPA in dodecane. The results of this condition were the distribution coefficient of Gd = 2,226, the distribution coefficient of Dy = 3,762, and the separation factor of Gd/Dy = 0,592. (author)

Thermodynamic assessment of the Bi–Er and the Bi–Dy systems

International Nuclear Information System (INIS)

Wang, Jinsan; Li, Changrong; Guo, Cuiping; Du, Zhenmin; Wu, Bo

2013-01-01

Highlights: • The Bi–Er and Bi–Dy binary systems were optimized. • The first-principles method was used to calculate formation enthalpies of compounds. • A self-consistent set of thermodynamic parameters were obtained. • The experimental and calculated data were well reproduced by the optimized results. - Abstract: Based on the available experimental data, the Bi–Er and the Bi–Dy binary systems have been assessed thermodynamically using the CALPHAD (CALculaton of PHAse Diagram) technique. The formation enthalpies at 0 K of the compounds, Bi 3 Er 5 , BiEr, Bi 3 Dy 5 and BiDy, were calculated by the first-principles method and Birch–Murnaghan equation of state, and the calculated results were used in the present thermodynamic optimization. All these compounds in the Bi–Er and the Bi–Dy systems were treated as stoichiometric compounds. The liquid phase was modeled as a substitutional solution phase based on random mixing of the constituent atoms and the excess Gibbs energy was formulated with the Redlich–Kister polynomial. Good agreements were obtained between the calculated results and the experimental data for both the thermochemical properties and the phase equilibrium relations

Luminescent properties in films of ZrO2: Dy

International Nuclear Information System (INIS)

Martinez, R. C.; Guzman, J.; Rivera, T.; Ceron, P.; Montes, E.; Guzman, D.; Garcia H, M.; Falcony, C.; Azorin, J.

2014-08-01

In this work the luminescent characterization of zirconium oxide (ZrO 2 ) films impure with dysprosium (Dy +3 ) is reported, obtained by means of the ultrasonics spray pyrolysis technique. The films were deposited on glass substrates (Corning), in a temperatures interval of 400 to 550 grades C, using as precursor elements Zirconium oxide chloride octahydrate (ZrOCl 2 ·8H 2 O) and Dysprosium tri-chloride (DyCl 3 ), dissolved in deionized water, varying the concentration of the contaminated from the 1 to 20 atomic % with relationship to the zirconium in solution. The luminescent characterization was analyzed by means of photoluminescence and thermoluminescence. The photoluminescence results showed a spectrum with three maxima which correspond to the electronic transitions 4 F 9/2 - 6 H 15/2 , 4 F 9/2 - 6 H 13/2 and 4 F 9/2 - 6 H 11/2 characteristics of the Dy 3+ ion. The thermoluminescence (Tl) response when being exposed to a monochrome UV beam in 240 nm showed a wide curve that exhibits a maxim centered in 200 grades C. The Tl response of ZrO 2 :Dy in function of the dose was shown lineal in the interval of 24 mJ/cm 2 to 432 mJ/cm 2 . A study of the repeatability and dissipation of the ZrO 2 :Dy Tl response is included. Considering the shown previous results we can conclude that the ZrO 2 in film form obtained by spray pyrolysis has luminescent properties in 240 nm. (Author)

Fading of LiF and CaF2:Dy

International Nuclear Information System (INIS)

Ben-Shachar, B.; German, U.; Weiser, G.

1983-03-01

The fading of LiF and CaF 2 :Dy was investigated and the results were compared to the literature. The effect of thermal annealing was studied in order to reduce the fading in both phosphors and to minimize the effects of the environment on CaF 2 :Dy. Minimizing the fading and knowing its time dependence make possible the exact personal and environmental dosimetry. (Author)

Application and evaluation of the mass spectrometric isotope dilution technique in the determination of rare earths in geological materials

International Nuclear Information System (INIS)

Moraes, N.M.P. de.

1988-01-01

Establishment of the experimental procedures employed in the rare earth element determination of geological samples by mass spectrometric isotope dilution analysis is discussed in the present work. The procedures involve preparation and calibration of the isotope tracers isotope dilution, dissolution in a teflon pressure vessel, chemical separation and isotope analysis using a fully automated Micromass VG ISOTOPES model 354 thermal ionization mass spectrometer. For the initial chemical separation of total rare earths the cationic resin was employed and HC1 and HNO 3 acids as eluents. In the second step rare earths elements were separated into individual (La, Ce and Nd) and subgroups (Sm-Eu-Gd, Yb-Er-Dy) fractions using the same cationic resin and α-HIBA as eluent. Nine elements La, Ce, Nd, Sm, Eu, Gd, Dy, Er and Yb are determined by this method in the ''United States Geological Survey'' (USGS) standard samples GSP-1, AGV-1 and G-2, with an overall precision of +- 1 to 2% and an accuracy of 5%. The concentration of rare earth element determined in the standard sample PCC-1 showed that the total analytical blanks are in submicrogram levels. The concentration of rare earth elements in the same USGS standard samples were also determined by Instrumental neutron activation analysis, neutron activation analysis with chemical separation before irradiation and inductively coupled argon plasma spectroscopy. The chemical procedures employed for these methods are the same as that used for mass spectrometric isotope dilution. Based on the results obtained, each method was evaluated pointing out their merits and defects. The study clearly showed that the chemical procedure employed for all these techniques was satisfactory. (author) [pt

Dielectrophoretic separation of gaseous isotopes

International Nuclear Information System (INIS)

McConnell, D.B.

1975-01-01

Gaseous isotopes are separated from a mixture in a vertically elongated chamber by subjecting the mixture to a nonuniform transverse electric field. Dielectrophoretic separation of the isotopes is effected, producing a transverse temperature gradient in the chamber, thereby enhancing the separation by convective countercurrent flow. In the example given, the process and apparatus are applied to the production of heavy water from steam

Study of crystal-field excitations and Raman active phonons in o-DyMnO3

International Nuclear Information System (INIS)

Jandl, S.; Mansouri, S.; Mukhin, A.A.; Yu Ivanov, V.; Balbashov, A.; Gospodino, M.M.; Nekvasil, V.; Orlita, M.

2011-01-01

In DyMnO 3 orthorhombic single crystals, the weak Raman active phonon softening below T=100 K is correlated with the study of infrared active Dy 3+ CF excitations as a function of temperature and under applied magnetic field. We detect five H 13/2 CF transitions that we predict with appropriate CF Hamiltonian and we confirm that the magnetic easy axis lies in the ab plane. While the CF energy level shifts below T=100 K reflect different displacements of the oxygen ions that contribute to the phonon softening, lifting of the ground state Kramers doublet degeneracy (∼30 cm -1 ) is observed below T N =39 K due to the anisotropic Mn 3+ -Dy 3+ interaction, which could be responsible for the stability of the bc-cycloid ferroelectric phase. - Research highlights: → Origin of Raman active phonon softening in the multiferroic o-DyMnO 3 . → A crystal-field study under magnetic field of Dy 3+ in o-DyMnO 3 . → Location of the magnetic easy axis in o-DyMnO 3 . → Lifting of Kramers doublet degeneracy in o-DyMnO 3 .

Topical and working papers on heavy water requirements and availability

International Nuclear Information System (INIS)

The documents included in this report are: Heavy water requirements and availability; technological infrastructure for heavy water plants; heavy water plant siting; hydrogen and methane availability; economics of heavy water production; monothermal, water fed heavy water process based on the ammonia/hydrogen isotopic exchange; production strategies to meet demand projections; hydrogen availability; deuterium sources; the independent UHDE heavy water process

Some kinetic properties of DySnSe2 combination

International Nuclear Information System (INIS)

Murguzov, M.I.; Mammadova, E.R.

2008-01-01

Recently, to the acquisition of multi-component alloys and combination in the presence of rare-earth metals (REM) interest has grown considerably. According to preliminary data, in the presence of rare-earth metals you can obtain perspective semiconductor materials which are of practical importance, and can be used in various fields of microelectronics in a complex system of chalcogenides. DySnSe 2 combination is also includes to this system. Physical peculiarities of these combinations have been studied in wide interval. DySnSe 2 combination crystallizes in ortho rhombic crystal system and is an indemnification n-type semiconductor material. The mechanism of electrical conductivity in DySnSe 2 semiconductor combination is complicated and cargo carrier scattering changes at low temperatures. That is why, the mixed type conductivity occurs

Synthesis and luminescence characteristics of Dy{sup 3+} doped KLa(PO{sub 3}){sub 4}

Energy Technology Data Exchange (ETDEWEB)

Chemingui, S.; Ferhi, M., E-mail: ferhi.mounir@gmail.com; Horchani-Naifer, K.; Férid, M.

2015-10-15

Polycrystalline powders of KLa{sub (1−x)}Dy{sub x}(PO{sub 3}){sub 4} (x=0.5%, 1%, 5% and 10%) with linear chain have been grown by solid state reaction. The obtained powders are characterized by X-ray powder diffraction, FTIR and Raman spectroscopies. Emission, excitation spectra and decay curves analysis have been used to study the spectroscopic properties of Dy{sup 3+} in KLa(PO{sub 3}){sub 4}. The photoluminescence spectra show two characteristic blue and yellow bands of Dy{sup 3+}. The yellow-to-blue emission intensity ratios and CIE chromaticity coordinates have been determined from emission spectra to evaluate the emitted light as function of Dy{sup 3+} concentration. The measured decay rates for {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2} deviated from exponential to non-exponential shape with increase of Dy{sup 3+} concentration. The observed non-exponential behavior of the decay curve has been fitted to Inokuti–Hirayama model, which indicates that the energy transfer between the donor and the acceptor is of dipole–dipole nature. The energy transfer, between the donor (excited Dy{sup 3+}) and the acceptor (unexcited Dy{sup 3+}), increases with Dy{sup 3+} ions concentration. - Highlights: • Polycrystalline powders of KLa{sub (1−x)}Dy{sub x}(PO{sub 3}){sub 4} were grown by solid state reaction. • The obtained samples are characterized by XRD, FTIR and Raman spectroscopies. • The luminescent properties of Dy{sup 3+} in KLa(PO{sub 3}){sub 4} are investigated. • Lifetime and chromatic coordinates depend strongly on Dy{sup 3+} concentration. • White and blue emissions are obtained at high and low concentration, respectively.

CaSO4:DY,Mn: A new and highly sensitive thermoluminescence phosphor for versatile dosimetry

Science.gov (United States)

Bahl, Shaila; Lochab, S. P.; Kumar, Pratik

2016-02-01

With the advent of newer techniques for dose reduction coupled with the development of more sensitive detectors, the radiation doses in radiological medical investigation are decreasing. Nevertheless, keeping the tenet in mind that all radiation doses could entail risk, there is a need to develop more sensitive dosimeters capable of measuring low doses. This paper gives the account of the development of a new and sensitive phosphor CaSO4:Dy,Mn and its characterization. The standard production procedure based on the recrystallization method was used to prepare CaSO4:Dy,Mn. The Thermoluminescence (TL) studies were carried out by exposing it with gamma radiation (Cs-137) from 10 μGy to 100 Gy. The theoretical studies to determine the number of peaks and kinetic parameters related to the TL glow peaks in CaSO4:Dy,Mn was performed using the Computerized Glow Curve Deconvolution (CGCD) method. Experiments were performed to determine optimum concentration of the dopants Dysprosium (Dy) and Mangnese (Mn) in the host CaSO4 so that maximum sensitivity of the phosphor may be achieved. The optimum dopant concentration turned out to be 0.1 mol%. As there were two dopants Dy and Mn their relative ratio were varied in steps of 0.025 keeping the concentration of total dopant (Dy and Mn) 0.1 mol% always. The maximum TL intensity was seen in the CaSO4:Dy(0.025),Mn(0.075) combination. The TL sensitivity of this phosphor was found to be about 2 and 1.8 times higher than that of popular phosphor CaSO4:Dy and LiF:Mg,Cu,P (TLD-700H) respectively. This new phosphor CaSO4:Dy,Mn showed fading of 11% which is similar to that of the standard phosphor CaSO4:Dy. The paper concludes that the new, highly sensitive TL phosphor CaSO4:Dy,Mn has shown higher sensitivity and hence the potential to replace commonly used CaSO4:Dy.

Protein-based stable isotope probing.

Science.gov (United States)

Jehmlich, Nico; Schmidt, Frank; Taubert, Martin; Seifert, Jana; Bastida, Felipe; von Bergen, Martin; Richnow, Hans-Hermann; Vogt, Carsten

2010-12-01

We describe a stable isotope probing (SIP) technique that was developed to link microbe-specific metabolic function to phylogenetic information. Carbon ((13)C)- or nitrogen ((15)N)-labeled substrates (typically with >98% heavy label) were used in cultivation experiments and the heavy isotope incorporation into proteins (protein-SIP) on growth was determined. The amount of incorporation provides a measure for assimilation of a substrate, and the sequence information from peptide analysis obtained by mass spectrometry delivers phylogenetic information about the microorganisms responsible for the metabolism of the particular substrate. In this article, we provide guidelines for incubating microbial cultures with labeled substrates and a protocol for protein-SIP. The protocol guides readers through the proteomics pipeline, including protein extraction, gel-free and gel-based protein separation, the subsequent mass spectrometric analysis of peptides and the calculation of the incorporation of stable isotopes into peptides. Extraction of proteins and the mass fingerprint measurements of unlabeled and labeled fractions can be performed in 2-3 d.

Dyeing of white and indigo dyed cotton fabrics with Mimosa tenuiflora extract

Directory of Open Access Journals (Sweden)

Gökhan Erkan

2014-04-01

Full Text Available Mimosa tenuiflora extract has been used in food industry as an additive and in textile and leather industry as a colorant. Two types of fabrics, ready to be dyed white and indigo dyed fabrics, were dyed with M. tenuiflora extract. The fabrics were mordanted after dyeing with six different metal salts. Colorimetric evaluations of fabrics were carried out by spectrophotometer. Colour fastness to washing, rubbing and light were performed. Colour strength of fabrics was calculated from Kubelka–Munk formula. Highest vividness (C∗ values were obtained by Ni mordant. Moderate fastness values were observed. However poor wet rubbing fastness values were observed in the case of indigo dyed fabrics due to lack of good wet rubbing fastness of indigo itself.

Interhemispheric leakage of isotopically heavy nitrate in the eastern tropical Pacific during the last glacial period

Science.gov (United States)

Pichevin, Laetitia E.; Ganeshram, Raja S.; Francavilla, Stephen; Arellano-Torres, Elsa; Pedersen, Tom F.; Beaufort, Luc

2010-02-01

We present new high-resolution N isotope records from the Gulf of Tehuantepec and the Nicaragua Basin spanning the last 50-70 ka. The Tehuantepec site is situated within the core of the north subtropical denitrification zone while the Nicaragua site is at the southern boundary. The δ15N record from Nicaragua shows an “Antarctic” timing similar to denitrification changes observed off Peru-Chile but is radically different from the northern records. We attribute this to the leakage of isotopically heavy nitrate from the South Pacific oxygen minimum zone (OMZ) into the Nicaragua Basin. The Nicaragua record leads the other eastern tropical North Pacific (ETNP) records by about 1000 years because denitrification peaks in the eastern tropical South Pacific (ETSP) before denitrification starts to increase in the Northern Hemisphere OMZ, i.e., during warming episodes in Antarctica. We find that the influence of the heavy nitrate leakage from the ETSP is still noticeable, although attenuated, in the Gulf of Tehuantepec record, particularly at the end of the Heinrich events, and tends to alter the recording of millennial timescale denitrification changes in the ETNP. This implies (1) that sedimentary δ15N records from the southern parts of the ETNP cannot be used straightforwardly as a proxy for local denitrification and (2) that denitrification history in the ETNP, like in the Arabian Sea, is synchronous with Greenland temperature changes. These observations reinforce the conclusion that on millennial timescales during the last ice age, denitrification in the ETNP is strongly influenced by climatic variations that originated in the high-latitude North Atlantic region, while commensurate changes in Southern Ocean hydrography more directly, and slightly earlier, affected oxygen concentrations in the ETSP. Furthermore, the δ15N records imply ongoing physical communication across the equator in the shallow subsurface continuously over the last 50-70 ka.

High coercivity in Fe-Nb-B-Dy bulk nanocrystalline magnets

Energy Technology Data Exchange (ETDEWEB)

Ziolkowski, Grzegorz; Chrobak, Artur; Klimontko, Joanna [Institute of Physics, University of Silesia, Uniwersytecka 4, 40-007, Katowice (Poland); Chrobak, Dariusz; Rak, Jan [Institute of Materials Science, University of Silesia, 75 Pulku Piechoty 1, 41-500, Chorzow (Poland); Zivotsky, Ondrej; Hendrych, Ales [Department of Physics, VSB-TU Ostrava, Ostrava (Czech Republic)

2016-11-15

The paper refers to structural and magnetic properties of the (Fe{sub 80}Nb{sub 6}B{sub 14}){sub 1-x}Dy{sub x} (x = 0.08, 0.10, 0.12, 0.16) bulk nanocrystalline alloys prepared by making use of the vacuum suction casting technique. The samples are in a form of rods with different diameters d = 1.5, 1, and 0.5 mm. The phase structure was investigated by XRD technique and reveals an occurrence of magnetically hard Dy{sub 2}Fe{sub 14}B as well as other relatively soft Dy-Fe, Fe-B, and Fe phases dependently on the Dy content. The alloys show hard magnetic properties with high coercive field up to 5.5 T (for x = 0.12 and d = 0.5 mm). The observed magnetic hardening effect with the increase of cooling rate (decrease of sample diameter d) can be attributed to a formation of ultra-hard magnetic objects as well as increasing role of low dimensional microstructure. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Electronic structure and magnetic properties of Dy adatom on Ir surface

Science.gov (United States)

Shick, A. B.; Lichtenstein, A. I.

2018-05-01

The electronic structure and magnetism of individual Dy atom adsorbed on the (1 1 1) surface of Ir is investigated using the combination of the density functional theory with the Hubbard-I approximation to the Anderson impurity model (DFT + HIA). The Dy3+ adatom is found magnetic with the magnetic moment of 9.35μB in the external magnetic field. The spin and orbital magnetic moments, and their ratio are evaluated, and compared with the X-ray magnetic circular dichroism data. The positive magnetic anisotropy energy of ≈ 1.3 meV determines the out-of-plane orientation of the Dy adatom magnetic moment. The role of 5d-4f interorbital exchange polarization in modification of the 4f shell energy spectrum is emphasized. We predict the Dy magnetization to drop by the factor of three with switching off the external magnetic field.

Magnetostrictive effects in ferromagnetic Dy break-junctions

Energy Technology Data Exchange (ETDEWEB)

Mueller, Marc; Suergers, Christoph; Montbrun, Richard [Karlsruher Institut fuer Technologie, Physikalisches Institut, 76131 Karlsruhe (Germany); Loehneysen, Hilbert v. [Karlsruher Institut fuer Technologie, Physikalisches Institut, 76131 Karlsruhe (Germany); Karlsruher Institut fuer Technologie, Institut fuer Festkoerperphysik, 76021 Karlsruhe (Germany)

2011-07-01

A characteristic property of the rare-earth metals are their large magnetostrictive strains which are related to the magnetocrystalline anisotropy through the elastic energy. We have investigated the electrical conductance G of mechanical break-junctions of a dysprosium wire at 4.2 K where Dy is in the ferromagnetic state. In zero magnetic field we find the usual variation of the conductance G vs. electrode distance x while breaking the wire mechanically, with a sequence of steps and more or less prominent plateaus. The behavior G(x) is modified in magnetic fields {mu}{sub 0} H up to 1 T due to the large magnetostriction of Dy. In addition, the conductance can be changed reproducibly by variation of H. For a number of contacts we observe discrete changes in G(H) in the range of several G{sub 0} = 2 e{sup 2}/h. The behavior of G(H) and its angular dependence can be quantitatively understood by taking into account the magnetostrictive properties of Dy. This first realization of a magnetostrictive atomic switch demonstrates the possibility of reproducibly tuning the conductance of magnetic nanocontacts by a magnetic field.

Dielectrophoretic separation of gaseous isotopes

International Nuclear Information System (INIS)

McConnell, D.B.

1976-01-01

This invention relates to a process for the separation of gaseous isotopes by electrophoresis assisted by convective countercurrent flow and to an apparatus for use in the process. The invention is especially applicable to heavy water separation from steam; however, it is to be understood that the invention is broadly applicable to the separation of gaseous isotopes having different dipole moments and/or different molecular weights. (author)

Luminescence studies of SrAl_2O_4:Dy"3"+ nanophosphors

International Nuclear Information System (INIS)

Sharma, Ravi

2016-01-01

Nanosized strontium aluminate phosphors activated by Dy"3"+ were prepared by combustion as well as by solid state reaction method. Nanophosphor was prepared by these methods at reaction temperatures 600°C and 1200°C respectively. Powder X-ray diffraction (XRD), scanning electron microscope analysis was used to characterize the prepared product. Themonoclinic phase was observed in the XRD pattern. The particle size of the samples was calculated around 35 nm. The SEM images show irregular shape of the prepared nanophosphor. Two peaks were found in the Mechanoluminescence (ML) response curve plotted between time and ML intensity. The H_3BO_3 added strontium aluminate phosphors activated with Dy show more bright ML peak as compared to the powders of SrAl_2O_4:Dy"3"+ without H_3BO_3. It was found that the PL and ML intensity increases with increasing concentration of Dy. The intensity becomes maximum for 3% of Dy. The photoluminescence emission shows two intense fluorescence transitions peaks at 498 nm and 583 nm, "4F_9_/_2 → "6H_1_5_/_2 in the blue and "4F_9_/_2 → "6H_1_3_/_2 in the yellow-orange wavelength region. (author)

Magnetic and Moessbauer studies on GdCo3B2 and DyCo3B2

International Nuclear Information System (INIS)

Malik, S.K.; Umarji, A.M.; Shenoy, G.K.

1984-10-01

Magnetization and Moessbauer studies have been carried out on GdCo 3 B 2 and DyCo 3 B 2 . These compounds are magnetically ordered with Curie temperatures of 56 0 and 21 0 K respectively. The Co atoms are either nonmagnetic or carry a small moment in these compounds. The saturation moment of DyCo 3 B 2 at 5 0 K is smaller than the Dy 3+ free-ion value. From 161 Dy Moessbauer studies, the measured hyperfine magnetic field at the Dy site is also observed to be smaller than the free-ion value. 155 Gd Moessbauer measurements in GdCo 3 B 2 reveal the presence of large crystalline electric fields at the rare earth site. This causes the moment and the hyperfine field at the Dy site in DyCo 3 B 2 to be reduced from its free-ion value

CaSO{sub 4}:Dy microphosphor for thermal neutron dosimetry

Energy Technology Data Exchange (ETDEWEB)

Bhadane, Mahesh S. [Microtron Accelerator Laboratory, Department of Physics, Savitribai Phule Pune University, Pune 411007 (India); Mandlik, Nandkumar [Department of Physics, Fergusson College, Savitribai Phule Pune University, Pune 411007 (India); Patil, B.J. [Department of Physics, Abasaheb Garware College, Pune 411004 (India); Dahiwale, S.S.; Sature, K.R.; Bhoraskar, V.N. [Microtron Accelerator Laboratory, Department of Physics, Savitribai Phule Pune University, Pune 411007 (India); Dhole, S.D., E-mail: sanjay@physics.unipune.ac.in [Microtron Accelerator Laboratory, Department of Physics, Savitribai Phule Pune University, Pune 411007 (India)

2016-02-15

Dysprosium-doped calcium sulphate (CaSO{sub 4}:Dy) microphosphor was synthesized by acid re-crystallization method and its thermoluminescence (TL) properties irradiated with thermal neutrons was studied. Structural and morphological characteristics have been studied using X-ray diffraction and SEM which mainly exhibits a orthorhombic structure with particle size of 200 to 250 µm. Moreover, thermal neutron dosimetric characteristics of the microphosphor such as thermoluminescence glow curve, TL dose–response have been studied. This microphosphor powder represents a TL glow peak (T{sub max}) centered at around 240 °C. The TL response of CaSO{sub 4}:Dy microphosphor as a function of thermal neutron fluence is observed to be very linear upto the fluence of 52×10{sup 11} n/cm{sup 2} and further saturates. In addition, TL glow curves were deconvoluted by computerized glow curve deconvolution (CGCD) method and corresponding trapping parameters have been determined. It has been found that for every deconvoluted peak there is change in the order of kinetics. Overall, the experimental results show that the CaSO{sub 4}:Dy microphosphor can have potential to be an effective thermal neutron dosimetry. - Highlights: • Acid-recrystallization method is used to prepare CaSO{sub 4}:Dy microphosphor • CaSO{sub 4}:Dy phosphor irradiated thermal neutrons for dosimetric application. • TL response curve showed to be a perfect linear. • Trapping parameters has been calculated using CGCD curve fitting.

Mean field analysis of exchange coupling in amorphous DyFe2-B alloy ribbons

International Nuclear Information System (INIS)

Lee, J.M.; Jung, J.K.; Lim, S.H.

2001-01-01

Experimental magnetization-temperature curves for melt-spun ribbons of amorphous alloys (Dy 0.33 Fe 0.67 ) 1-x B x with x=0, 0.05, 0.1 and 0.15 (in atomic fraction) are fitted with theoretical equations based on the mean field theory in order to investigate exchange couplings between constituent elements as a function of the B content. The sign of the exchange coupling between Dy and Fe is negative, indicating that the magnetization direction of Dy is antiparallel to that of Fe. The sign of the other two couplings are positive. The exchange coupling between Fe ions are greatest, while that between Dy ions is negligible. The exchange couplings between Fe ions, and between Dy and Fe increase with increasing B content, the increase of the latter being much greater than the former. Resulting, the exchange coupling between Dy and Fe becomes about one half of that between Fe ions at the highest B content. The increase of the exchange coupling between Fe ions may be explained by the increase of the Fe-Fe separation with the increase of the B content. The total magnetization is dominated by the Dy sublattice magnetization. As the B content increases, the magnetization decreases over the whole temperature range, and the Curie temperature also decreases

Effect of Dy addition on mechanical and magnetic properties of Mn-rich Ni–Mn–Ga ferromagnetic shape memory alloys

International Nuclear Information System (INIS)

Gao, L.; Dong, G.F.; Gao, Z.Y.; Cai, W.

2012-01-01

Highlights: ► The Dy addition significantly improves the compressive properties of Ni–Mn–Ga alloy. ► The mechanism of the improved mechanical properties by adding Dy is discussed. ► Dy doping results in a change of the fracture type of Ni–Mn–Ga alloy. ► Curie temperature almost remained unchanged at low Dy content and then decreases. - Abstract: The effects of partial substitution of rare earth Dy for Ga on the mechanical and magnetic properties of Mn-rich Ni 50 Mn 29 Ga 21−x Dy x (0 ≤ x ≤ 5) ferromagnetic shape memory alloys were investigated in detail. The results show that an appropriate amount of Dy addition significantly improves the mechanical properties of Ni–Mn–Ga alloy. With an increase in Dy content, the compressive strength enhances rapidly at first and then becomes stable when the Dy content is more than 1 at.%. However, the compressive strain increases dramatically and reaches a maximum value with 1 at.% Dy addition. Further increase in Dy content makes the compressive strain of the alloys decrease gradually. The mechanism of the improved mechanical properties is also discussed. Moreover, Dy doping changes the fracture type from intergranular fracture of Ni–Mn–Ga alloy to transgranular cleavage fracture of Ni–Mn–Ga–Dy alloys. The Curie temperature remains almost unchanged at low Dy content and subsequently decreases.

Isotopically (δ13C and δ18O) heavy volcanic plumes from Central Andean volcanoes: a field study

Science.gov (United States)

Schipper, C. Ian; Moussallam, Yves; Curtis, Aaron; Peters, Nial; Barnie, Talfan; Bani, Philipson; Jost, H. J.; Hamilton, Doug; Aiuppa, Alessandro; Tamburello, Giancarlo; Giudice, Gaetano

2017-08-01

Stable isotopes of carbon and oxygen in volcanic gases are key tracers of volatile transfer between Earth's interior and atmosphere. Although important, these data are available for few volcanoes because they have traditionally been difficult to obtain and are usually measured on gas samples collected from fumaroles. We present new field measurements of bulk plume composition and stable isotopes (δ13CCO2 and δ18OH2O+CO2) carried out at three northern Chilean volcanoes using MultiGAS and isotope ratio infrared spectroscopy. Carbon and oxygen in magmatic gas plumes of Lastarria and Isluga volcanoes have δ13C in CO2 of +0.76‰ to +0.77‰ (VPDB), similar to slab carbonate; and δ18O in the H2O + CO2 system ranging from +12.2‰ to +20.7‰ (VSMOW), suggesting significant contributions from altered slab pore water and carbonate. The hydrothermal plume at Tacora has lower δ13CCO2 of -3.2‰ and δ18OH2O+CO2 of +7.0‰, reflecting various scrubbing, kinetic fractionation, and contamination processes. We show the isotopic characterization of volcanic gases in the field to be a practical complement to traditional sampling methods, with the potential to remove sampling bias that is a risk when only a few samples from accessible fumaroles are used to characterize a given volcano's volatile output. Our results indicate that there is a previously unrecognized, relatively heavy isotopic signature to bulk volcanic gas plumes in the Central Andes, which can be attributed to a strong influence from components of the subducting slab, but may also reflect some local crustal contamination. The techniques we describe open new avenues for quantifying the roles that subduction zones and arc volcanoes play in the global carbon cycle.

Effects of Dy and Nb on the magnetic properties and corrosion resistance of sintered NdFeB

International Nuclear Information System (INIS)

Yu, L.Q.; Wen, Y.H.; Yan, M.

2004-01-01

Dy and Nb were added into the sintered NdFeB magnets with the aim of improving their magnetic properties and corrosion resistance. It was found that intrinsic coercivity of magnets is promoted whilst remanence is reduced as a result of Dy addition. Simultaneous addition of Dy and Nb not only gives rise to greatly improved coercivity, but also suppresses the undesirable effect of Dy on the remanence. The optimum magnetic properties were achieved when 1.0% Dy and 1.5% Nb were incorporated. Moreover, corrosion resistance of NdFeB magnets improves with the increase in the content of Dy and Nb

Heavy ion reactions at high energies

International Nuclear Information System (INIS)

Jakobsson, Bo.

1977-01-01

A review on heavy ion experiments at energies >0.1GeV/nucleon is presented. Reaction cross-sections, isotope production cross-sections and pion production in nucleus-nucleus collisions are discussed. Some recent models for heavy ion reactions like the abrasion-ablation model, the fireball model and the different shock-wave models are also presented

Modern rather than Mesoarchaean oxidative weathering responsible for the heavy stable Cr isotopic signatures of the 2.95 Ga old Ijzermijn iron formation (South Africa)

Science.gov (United States)

Albut, Gülüm; Babechuk, Michael G.; Kleinhanns, Ilka C.; Benger, Manuela; Beukes, Nicolas J.; Steinhilber, Bernd; Smith, Albertus J. B.; Kruger, Stephanus J.; Schoenberg, Ronny

2018-05-01

Previously reported stable Cr isotopic fractionation in Archaean paleosols and iron formations (IFs) have been interpreted as a signature of oxidative weathering of Cr(III) to Cr(VI) in soils, and delivery of isotopically heavy Cr(VI) into the oceans. One of the oldest reported fingerprints of this process is isotopically heavy Cr preserved in the 2.95 Ga old Ijzermijn IF, Sinqeni Formation of the Mozaan Group (Pongola Supergroup), South Africa and could suggest that atmospheric free oxygen was present ca. 600 million years earlier than the Great Oxidation Event (GOE). However, fractionated stable Cr isotopic signatures have only been found to date in surface outcrop samples of the White Mfolozi Inlier exposed along the White Mfolozi River Gorge. In this study, the latter outcrop was resampled along with two drill cores of the Ijzermijn IF and a drill core of the Scotts Hill IF to represent multiple exposures of Mozaan Group IFs with different states of preservation. A detailed geochemical comparison on bulk samples of different units was undertaken using stable Cr isotopes coupled with trace and major elements. Outcrop iron-rich mudstones (Fe - lutites) show very low LOI [wt] %, and very low Fe(II)/Fetot ratios, and lower Ca and Mg relative to equivalent facies in drill cores, indicating the effects that oxidative recent surface weathering had on Fe/Mn-rich carbonate minerals of the IF. Overall rare earth element and yttrium (REE + Y) mixing models agree well with previous studies, confirming that they were minimally disturbed by weathering and are consistent with a high magnitude of continental solutes delivered in a near-shore depositional environment, with a minor contribution of hydrothermally derived fluids that upwelled into shallower depositional setting. Importantly, all drill core samples of this study revealed δ53/52Cr values within the igneous inventory, despite variable amounts of detrital Cr input that includes nearly detritus-free, chert

Program of critical experiment and measurements at the RA reactor; Program kriticnih eksperimenata i merenja na reaktoru RA

Energy Technology Data Exchange (ETDEWEB)

NONE

1960-04-14

Program described in this document describes in detail the following experiments: critical experiments with two reactor core lattices with 38 and 44 fuel channels, initial heavy water level being 1300 mm, criticality is achieved by adding heavy water; preliminary analysis of heavy water quality and verification of the fuel isotopic contents; experiment with the initial core which contains 56 fuel channels with maximum heavy water level according to the Russian proposal; measurement of neutron flux by Dy and In foils; measurement of reactivity excess dependent on the heavy water level and number of fuel rods; measurement of reactor period for determined reactivity change; measurement of moderator temperature coefficient; measurement of absolute flux. [Serbo-Croat] Program sadrzan u ovom dokumentu opisuje detaljno sledece eksperimente: kriticni eksperiment sa dve konfiguracije jezgra reaktora, sa 38 i 44 gorivna kanala, pocetni nivo teske vode je 1300 mm, kriticnost se dostize dodavanjem teske vode; prethodno izvrsenom analizom teske vode i proverom izotopskog sastava goriva; eksperiment sa pocetnom resetkom koja prema ruskom predlogu sadrzi 56 gorivnih kanala i maksimalnom visinom teske vode; merenje raspodele neutronskog fluksa folijama Dy i In; kalibracija regulacionih sipki; merenje viska reaktivnosti sa promenom visine nivoa teske vode i promenom broja sipki; merenje periode reaktora za odredjenu promenu reaktivnosti; merenje temperaturnog koeficijenta za vodu; merenje apsolutnog fluksa.

Muzeum módy - Tokyo 2010

OpenAIRE

Kráľová, Zuzana

2010-01-01

navrhovaný objekt je múzeum módy pre mesto Tokio. Múzeum sa bude nachádzať na pulzujúcej tepne tokijského módneho diania. Navrhovaná budova presahuje 100m výšky a jej zbierky mapujú vývoj svetovej módy 20.storčia. Taktiež je dejiskom konania živých módnych show a priestorom pre prezentáciu tvorby mladých módnych tvorcov. Samotné artefakty zbierky sú vystavované jednotným systémom - zavesením. visiace figuríny prechádzajú kontinuálne celým výstavným priestorom, návštevníkovi je umožnený pohyb ...

Isotopic anomalies - chemical memory of Galactic evolution

International Nuclear Information System (INIS)

Clayton, D.D.

1988-01-01

New mechanisms for the chemical memory of isotopic anomalies are proposed which are based on the temporal change during the chemical evolution of the Galaxy of the isotopic composition of the mean ejecta from stars. Because of the differing temporal evolution of primary and secondary products of nucleosynthesis, the isotopic composition of the bulk interstellar medium changes approximately linearly with time, and thus any dust component having an age different from that of average dust will be isotopically anomalous. Special attention is given to C, O, Mg, Si, and isotopically heavy average-stellar condensates of SiC. 20 references

Calcium hydroxide isotope effect in calcium isotope enrichment by ion exchange

International Nuclear Information System (INIS)

Jepson, B.E.; Shockey, G.C.

1984-01-01

The enrichment of calcium isotopes has been observed in ion-exchange chromatography with an aqueous phase of calcium hydroxide and a solid phase of sulfonic acid resin. The band front was exceedingly sharp as a result of the acid-base reaction occuring at the front of the band. Single-stage separation coefficients were found to be epsilon( 44 Ca/ 40 Ca) = 11 x 10 -4 and epsilon( 48 Ca/ 40 Ca) = 18 x 10 -4 . The maximum column separation factors achieved were 1.05 for calcium-44 and 1.09 for calcium-48 with the heavy isotopes enriching in the fluid phase. The calcium isotope effect between fully hydrated aqueous calcium ions and undissociated aqueous calcium hydroxide was estimated. For the calcium-44/40 isotope pair the separation coefficient was 13 x 10 -4 . 20 references, 2 figures

Tritium concentration in the heavy water upgrading plants

International Nuclear Information System (INIS)

Croitoru, C.; Pop, F.; Titescu, Gh.; Dumitrescu, M.; Ciortea, C.; Stefanescu, I.; Peculea, M.; Pitigoi, Gh.; Trancota, D. . E-mail of corresponding author: croitoru@icsi.ro; Croitoru, C.)

2005-01-01

In the course of time heavy water used in CANDU nuclear power plants, as moderator or coolant, degrades, as a result of its impurification with light water and tritium. Concentration diminution below 99.8% mol for moderator and 99.75% mol for coolant causes an inefficient functioning of CANDU reactor. By isotopic distillation, light water is removed. Simultaneously tritium concentration takes place. The heavy water upgrading plant from Cernavoda is an isotopic separation cascade with two stages. The paper presents, for this plant, a theoretical study of the tritium concentration. (author)

Synthesis and luminescence properties of novel LiSrPO{sub 4}:Dy{sup 3+} phosphor

Energy Technology Data Exchange (ETDEWEB)

Sun, Jiayue, E-mail: jiayue_sun@126.com [School of Science, Beijing Technology and Business University, Beijing 100048 (China); Zhang, Xiangyan [School of Science, Beijing Technology and Business University, Beijing 100048 (China); Xia, Zhiguo, E-mail: xiazg426@yahoo.com.cn [School of Materials Sciences and Technology, China University of Geosciences, Beijing 100083 (China); Du, Haiyan [School of Science, Beijing Technology and Business University, Beijing 100048 (China)

2011-11-15

Graphical abstract: Novel LiSrPO4:Dy{sup 3+} phosphors were synthesized by solid-state reaction, and Dy{sup 3+}-doped concentration dependent luminescence properties, concentration quenching effect and the decay times were investigated in detail. Highlights: {yields} LiSrPO{sub 4}:Dy{sup 3+} could be excited by UV light and exhibited blue and yellow emission. {yields} Concentration quenching effect of LiSrPO{sub 4}:Dy{sup 3+} samples were investigated in detail. {yields} Decay times are estimated to be 0.57-0.89 ms for Dy{sup 3+} in LiSrPO{sub 4} host. -- Abstract: Novel LiSrPO{sub 4}:Dy{sup 3+} phosphors for white light-emitting diodes (w-LEDs) were synthesized by the conventional solid-state reaction. X-ray powder diffraction (XRD) analysis confirmed the phase formation of LiSrPO{sub 4}:Dy{sup 3+} materials. Luminescence properties results showed that the phosphor could be efficiently excited by the UV-vis light region from 250 to 460 nm, and it exhibited blue (483 nm) and yellow (574 nm) emission corresponding to {sup 4}F{sub 9/2} {yields} {sup 6}H{sub 15/2} transitions and {sup 4}F{sub 9/2} {yields} {sup 6}H{sub 13}/{sub 2} transitions, respectively. The luminescence intensity of LiSrPO{sub 4}:xDy{sup 3+} phosphor firstly increased and then decreased with increasing Dy{sup 3+} concentration, and reached the maximum at x = 0.03. It was found that concentration quenching occurred as a result of dipole-dipole interaction according to the Dexter's theory. The decay time was also determined for various concentrations of Dy{sup 3+} in LiSrPO{sub 4}.

Chromium stable isotope fractionation in modern biogeochemical cycling

DEFF Research Database (Denmark)

Paulukat, Cora Stefanie

oxygen in the Earth’s atmosphere. Oxidative rock weathering on land induces oxidation of immobile Cr(III) to mobile Cr(VI). Isotopically relatively heavy Cr(VI) is released to runoff, and transported by rivers to the oceans, where it is incorporated into chemical sediments and carbonate shells...... laterite soils from India, formed on ultramafic rocks, indicates extensive leaching of isotopically heavy Cr(VI). Transferring this knowledge to ancient weathering profiles, negatively fractionated Cr is clear evidence for the presence of free oxygen in the atmosphere. The second part demonstrates...

Neutron capture measurements and resonance parameters of dysprosium

Energy Technology Data Exchange (ETDEWEB)

Shin, S.G.; Kye, Y.U.; Namkung, W.; Cho, M.H. [Pohang University of Science and Technology, Division of Advanced Nuclear Engineering, Pohang, Gyeongbuk (Korea, Republic of); Kang, Y.R.; Lee, M.W. [Dongnam Inst. of Radiological and Medical Sciences, Research Center, Busan (Korea, Republic of); Kim, G.N. [Kyungpook National University, Department of Physics, Daegu (Korea, Republic of); Ro, T.I. [Dong-A University, Department of Physics, Busan (Korea, Republic of); Danon, Y.; Williams, D. [Rensselaer Polytechnic Institute, Department of Mechanical, Aerospace, and Nuclear Engineering, Troy, NY (United States); Leinweber, G.; Block, R.C.; Barry, D.P.; Rapp, M.J. [Naval Nuclear Laboratory, Knolls Atomic Power Laboratory, Schenectady, NY (United States)

2017-10-15

Neutron capture yields of dysprosium isotopes ({sup 161}Dy, {sup 162}Dy, {sup 163}Dy, and {sup 164}Dy) were measured using the time-of-flight method with a 16 segment sodium iodide multiplicity detector. The measurements were made at the 25m flight station at the Gaerttner LINAC Center at Rensselaer Polytechnic Institute. Resonance parameters were obtained using the multilevel R-matrix Bayesian code SAMMY. The neutron capture data for four enriched dysprosium isotopes and one natural dysprosium sample were sequentially fitted. New resonances not listed in ENDF/B-VII.1 were observed. There were 29 and 17 new resonances from {sup 161}Dy and {sup 163}Dy isotopes, respectively. Six resonances from {sup 161}Dy isotope, two resonances from {sup 163}Dy, and four resonances from {sup 164}Dy were not observed. The capture resonance integrals of each isotope were calculated with the resulting resonance parameters and those of ENDF/B-VII.1 in the energy region from 0.5 eV to 20 MeV and were compared to the capture resonance integrals with the resonance parameters from ENDF/B-VII.1. A resonance integral value of the natural dysprosium calculated with present resonance parameters was 1405 ± 3.5 barn. The value is ∝ 0.3% higher than that obtained with the ENDF/B-VII.1 parameters. The distributions of the present and ENDF/B-VII.1 neutron widths were compared to a Porter-Thomas distribution. Neutron strength functions for {sup 161}Dy and {sup 163}Dy were calculated with the present resonance parameters and both values were in between the values of ''Atlas of Neutron Resonances'' and ENDF/B-VII.1. The present radiation width distributions of {sup 161}Dy and {sup 163}Dy were fitted with the χ{sup 2} distribution by varying the degrees of freedom. (orig.)

Size-dependent structure and magnetic properties of DyMnO3 nanoparticles

International Nuclear Information System (INIS)

Cai, Xuan; Shi, Lei; Zhou, Shiming; Zhao, Jiyin; Guo, Yuqiao; Wang, Cailin

2014-01-01

The structure and magnetic properties of orthorhombic DyMnO 3 nanoparticles with different particle sizes are investigated in this paper. With decreasing particle size, all the lattice parameters a, b, and c gradually decrease, whereas the orthorhombic distortion increases. Magnetic measurements reveal that the antiferromagnetic interaction of Mn ions is weakened due to the decrease in Mn-O-Mn bond angle. Above a critical field H*, DyMnO 3 undergoes a field-induced metamagnetic transition at 4 K, which is related to the spin reversal of Dy moments. The critical field H* increases monotonically with size reduction, indicating an enhancement of the antiferromagnetic interaction of Dy ions due to the decreased distance between rare earth ions. The magnetization at 4 K and 5 T, i.e., M(4 K, 5 T) shows a non-monotonic variation with particle size d, i.e., M(4 K, 5 T) initially increases with size reduction but decreases again for d < 68 nm. A modified core-shell model, in which the ferromagnetic ordering (Dy magnetic structure) and antiferromagnetic ordering (Mn magnetic structure) coexist in the core, is proposed to explain this behavior.

Photoluminescence and thermoluminescence characterization of Eu3+- and Dy3+ -activated Ca3(PO4)2 phosphor

International Nuclear Information System (INIS)

Nagpure, I.M.; Saha, Subhajit; Dhoble, S.J.

2009-01-01

Rare-earth-doped polycrystalline Ca 3 (PO 4 ) 2 :Eu, Ca 3 (PO 4 ) 2 :Dy and Ca 3 (PO 4 ) 2 :Eu,Dy phosphors prepared by a modified solid-state synthesis has been studied for its X-ray diffraction, thermoluminescence (TL) and photoluminescence (PL) characteristics. The PL emission spectra of the phosphor suggest the presence of Eu 3+ ion in Ca 3 (PO 4 ) 2 :Eu and Dy 3+ ion in Ca 3 (PO 4 ) 2 :Dy lattice sites. The TL glow curve of the Ca 3 (PO 4 ) 2 :Eu compounds has a simple structure with a prominent peak at 228 deg. C, while Ca 3 (PO 4 ) 2 :Dy peaking at 146 and 230 deg. C. TL sensitivity of phosphors are compared with CaSO 4 : Dy and found 1.52 and 1.20 times less in Ca 3 (PO 4 ) 2 :Eu and Ca 3 (PO 4 ) 2 :Dy phosphors, respectively. The Ca 3 (PO 4 ) 2 :Eu,Dy phosphors shows switching behavior under two different excitation wavelengths and enhancement in PL intensity of Dy 3+ ions were reported. The paper discusses the photoluminescence and thermoluminescence behavior of Eu 3+ and Dy 3+ ion in Ca 3 (PO 4 ) 2 hosts, it may be applicable to solid-state lighting as well as thermoluminescence dosimetry applications.

Tailoring of magnetic properties of ultrathin epitaxial Fe films by Dy doping

Directory of Open Access Journals (Sweden)

A. A. Baker

2015-07-01

Full Text Available We report on the controlled modification of relaxation parameters and magnetic moments of epitaxial Fe thin films through Dy doping. Ferromagnetic resonance measurements show that an increase of Dy doping from 0.1% to 5% gives a tripling in Gilbert damping, and more importantly a strongly enhanced anisotropic damping that can be qualitatively understood through the slow-relaxing impurity model. X-ray magnetic circular dichroism measurements show a pronounced suppression of the orbital moment of the Fe with Dy doping, leading to an almost threefold drop in the orbital to spin moment ratio, ml/ms. Doping with Dy can therefore be used to control both dynamic and static properties of thin ferromagnetic films for improved performance in spintronics device applications, mediated through the antiferromagnetic interaction of the 4f and 3d states.

Tailoring of magnetic properties of ultrathin epitaxial Fe films by Dy doping

Energy Technology Data Exchange (ETDEWEB)

Baker, A. A. [Department of Physics, Clarendon Laboratory, University of Oxford, Oxford, OX1 3PU (United Kingdom); Magnetic Spectroscopy Group, Diamond Light Source, Didcot, OX11 0DE (United Kingdom); Figueroa, A. I.; Laan, G. van der [Magnetic Spectroscopy Group, Diamond Light Source, Didcot, OX11 0DE (United Kingdom); Hesjedal, T. [Department of Physics, Clarendon Laboratory, University of Oxford, Oxford, OX1 3PU (United Kingdom)

2015-07-15

We report on the controlled modification of relaxation parameters and magnetic moments of epitaxial Fe thin films through Dy doping. Ferromagnetic resonance measurements show that an increase of Dy doping from 0.1% to 5% gives a tripling in Gilbert damping, and more importantly a strongly enhanced anisotropic damping that can be qualitatively understood through the slow-relaxing impurity model. X-ray magnetic circular dichroism measurements show a pronounced suppression of the orbital moment of the Fe with Dy doping, leading to an almost threefold drop in the orbital to spin moment ratio, m{sub l}/m{sub s}. Doping with Dy can therefore be used to control both dynamic and static properties of thin ferromagnetic films for improved performance in spintronics device applications, mediated through the antiferromagnetic interaction of the 4f and 3d states.

Heavy Water - Industrial Separation Processes

International Nuclear Information System (INIS)

Peculea, M.

1984-01-01

This monograph devoted to the heavy water production mainly presents the Romanian experience in the field which started in early sixties from the laboratory scale production and reached now the level of large scale industrial production at ROMAG-Drobeta, Romania. The book is structured in eleven chapters entitled: Overview, The main physical properties, Sources, Uses, Separation factor and equilibrium constant, Mathematical modelling of the separation process, Thermodynamical considerations on the isotope separation, Selection criteria for heavy water separation processes, Industrial installations for heavy water production, Prospects, Acknowledgements. 200 Figs., 90 Tabs., 135 Refs

Optical and luminescence properties of Dy3+ doped sodium silicate glass

Science.gov (United States)

Srisittipokakun, N.; Kaewkhao, J.

2017-07-01

The aim of the present work is to study the optical and luminescence properties of Dy2O3 doped Na2O-BaO-Bi2O3-SiO2 glasses. The Dy3+ ion is chosen as dopant because it emits three visible bands, blue (470-485 nm; 4F9/2→6H15/2), yellow (570-580 nm; 4F9/2→6H13/2) and red (640-655 nm; 4F9/2→6H11/2) luminescence and finds its applications in the fields of laser, white LEDs, telecommunication technology and display devices. NaBaBiSiDy glasses with the compositions of (30-x)SiO2: 10Bi2O3: 30Na2O: 30BaO: xDy2O3 where x=0.0, 0.1, 0.5, 1.0, 1.5 and 2.0 mol% were prepared by melt-quenching technique and characterized by using density, optical absorption photoluminescence (PL) and decay rate measurements as function of different concentrations. The density (ρ), molar volume (VM) and refractive index obtained were found to increase with increase in the concentration of Dy2O3 in the glass matrix. The chromaticity coordinates were calculated from emission spectra and analyzed with CIE color diagram and appear in the white light region under ultraviolet excitation.

X-ray induced fluorescence measurement of segregation in a DyI{sub 3}-Hg metal-halide lamp

Energy Technology Data Exchange (ETDEWEB)

Nimalasuriya, T [Department of Applied Physics, Eindhoven University of Technology, PO Box 513, 5600 MB Eindhoven (Netherlands); Curry, J J [National Institute of Standards and Technology, 100 Bureau Drive, Stop 8422, Gaithersburg, MD 20899-8422 (United States); Sansonetti, C J [National Institute of Standards and Technology, 100 Bureau Drive, Stop 8422, Gaithersburg, MD 20899-8422 (United States); Ridderhof, E J [Department of Applied Physics, Eindhoven University of Technology, PO Box 513, 5600 MB Eindhoven (Netherlands); Shastri, S D [Advanced Photon Source, Argonne National Laboratory, Argonne, IL 60439 (United States); Flikweert, A J [Department of Applied Physics, Eindhoven University of Technology, PO Box 513, 5600 MB Eindhoven (Netherlands); Stoffels, W W [Department of Applied Physics, Eindhoven University of Technology, PO Box 513, 5600 MB Eindhoven (Netherlands); Haverlag, M [Department of Applied Physics, Eindhoven University of Technology, PO Box 513, 5600 MB Eindhoven (Netherlands); Mullen, J J A M van der [Department of Applied Physics, Eindhoven University of Technology, PO Box 513, 5600 MB Eindhoven (Netherlands)

2007-05-07

Segregation of elemental Dy in a DyI{sub 3}-Hg metal-halide high-intensity discharge lamp has been observed with x-ray induced fluorescence. Significant radial and axial Dy segregation are seen, with the axial segregation characterized by a Fischer parameter value of {lambda} = 0.215 {+-} 0.002 mm{sup -1}. This is within 7% of the value ({lambda} = 0.20 {+-} 0.01 mm{sup -1}) obtained by Flikweert et al (2005 J. Appl. Phys. 98 073301) based on laser absorption by neutral Dy atoms. Elemental I is seen to exhibit considerably less axial and radial segregation. Some aspects of the observed radial segregation are compatible with a simplified fluid picture describing two main transition regions in the radial coordinate. The first transition occurs in the region where DyI{sub 3} molecules are in equilibrium with neutral Dy atoms. The second transition occurs where neutral Dy atoms are in equilibrium with ionized Dy. These measurements are part of a larger study on segregation in metal-halide lamps under a variety of conditions.

Mechanical properties, corrosion, and biocompatibility of Mg-Zr-Sr-Dy alloys for biodegradable implant applications.

Science.gov (United States)

Ding, Yunfei; Lin, Jixing; Wen, Cuie; Zhang, Dongmei; Li, Yuncang

2017-11-28

This study investigates the microstructure, mechanical properties, corrosion behavior, and biocompatibility of magnesium (Mg)-based Mg1Zr2SrxDy (x = 0, 1, 1.63, 2.08 wt %) alloys for biodegradable implant applications. The corrosion behavior of the Mg-based alloys has been evaluated in simulated body fluid using an electrochemical technique and hydrogen evolution. The biocompatibility of the Mg-based alloys has been assessed using SaSO2 cells. Results indicate that the addition of Dy to Mg-Zr-Sr alloy showed a positive impact on the corrosion behavior and significantly decreased the degradation rates of the alloys. The degradation rate of Mg1Zr2Sr1.0Dy decreased from 17.61 to 12.50 mm year -1 of Mg1Zr2Sr2.08Dy based on the hydrogen evolution. The ultimate compressive strength decreased from 270.90 MPa for Mg1Zr2Sr1Dy to 236.71 MPa for Mg1Zr2Sr2.08Dy. An increase in the addition of Dy to the Mg-based alloys resulted in an increase in the volume fraction of the Mg 2 Dy phase, which mitigated the galvanic effect between the Mg 17 Sr 2 phase and the Mg matrix, and led to an increase in the corrosion resistance of the base alloy. The biocompatibility of the Mg-based alloys was enhanced with decreasing corrosion rates. Mg1Zr2Sr2.08Dy exhibited the lowest corrosion rate and the highest biocompatibility compared with the other Mg-based alloys. © 2017 Wiley Periodicals, Inc. J Biomed Mater Res Part B: Appl Biomater, 2017. © 2017 Wiley Periodicals, Inc.

On the basic substances used in the separation process by isotope exchange H2S - H2O, at two temperatures, in view of producing heavy water

International Nuclear Information System (INIS)

Popescu, V.

1977-01-01

In view of producing heavy water, the influence of the deuterium proportion in the basic substances, on the efficiency of the isotope exchange process H 2 S - H 2 O for two temperatures was studied. Heavy water is extracted from ordinary water and concentrated from 0.014 per cent to 5-15 per cent D 2 O by isotope bithermal exchange with the hydrogen sulphite. Theoretical and experimental research was carried out in laboratories and then applied on a pilot plant by designing and testing a drying equipment for hydrogen sulphite. The maximum H 2 S concentration rose to 99.84 per cent. The purity of the hydrogen sulphite resulting from the pilot plant, as well as the optimization of the installation for producing H 2 S depending on the deuterium distribution, make sure that the two methods for the preparation of sodium sulphite and hydrogen sulphite can be applied in industry. (author)

Determination of fission gas yields from isotope ratios

DEFF Research Database (Denmark)

Mogensen, Mogens Bjerg

1983-01-01

This paper describes a method of calculating the actual fission yield of Kr and Xe in nuclear fuel including the effect of neutron capture reactions and decay. The bases for this calculation are the cumulative yields (ref. 1) of Kr and Xe isotopes (or pairs of isotopes) which are unaffected...... by neutron capture reactions, and measured Kr and Xe isotope ratios. Also the burnup contribution from the different fissile heavy isotopes must be known in order to get accurate fission gas yields....

Dy163-Ho163 branching: an s-process barometer

International Nuclear Information System (INIS)

Beer, H.; Walter, G.; Macklin, R.L.

1984-01-01

The neutron capture cross sections of Dy163 and Er164 have been measured to analyze the s-process branching at Dy163-Ho163. The reproduction of the s-process abundance of Er164 via this branching is sensitive to temperature kT, neutron density, and electron density n/sub e/. The calculations using information from other branchings on kT and the neutron density n/sub n/ give constraints for n/sub e/ at the site of the s-process

Crystallographic and magnetic properties of (Nd,Dy)3Fe27.5(Ti,Mo)1.5 compounds

International Nuclear Information System (INIS)

Han, S.B.; Liu, X.F.; Lv, J.Y.; Peng, J.; Hao, Y.M.; Li, X.J.; Chen, D.F.; Xue, Y.J.; Li, J.H.; Hu, Z.B.

2006-01-01

A systematic study of the formation, structure and magnetic properties of (Nd,Dy) 3 Fe 27.5 (Ti,Mo) 1.5 compounds has been performed. Rietveld analyses of the X-ray patterns of the samples indicate that the concentrations of Ti and Mo affect the formation and structural properties slightly, whereas different rare-earth (Nd and Dy) contents influence them significantly. It is found that high Dy contents make it difficult to form the 3:29-type structures. The Curie temperatures of Nd 2.1 Dy 0.9 Fe 27.5 Ti 1.5- x Mo x decrease monotonically as more Ti was replaced by Mo but their saturation magnetizations remain almost unchanged; in contrast, for Nd 3- y Dy y Fe 27.5 TiMo 0.5 , their saturation magnetizations decrease monotonically with increasing Dy contents while their Curie temperatures are constant

Calculations of the magnetic entropy change in amorphous through a microscopic anisotropic model: Applications to Dy{sub 70}Zr{sub 30} and DyCo{sub 3.4} alloys

Energy Technology Data Exchange (ETDEWEB)

Ranke, P. J. von, E-mail: von.ranke@uol.com.br; Nóbrega, E. P.; Ribeiro, P. O.; Alvarenga, T. S. T.; Lopes, P. H. O.; Sousa, V. S. R. de; Oliveira, N. A. de [Instituto de Física, Universidade do Estado do Rio de Janeiro—UERJ, Rua São Francisco Xavier, 524, 20550-013 Rio de Janeiro (Brazil); Caldas, A. [Sociedade Unificada de Ensino Superior e Cultura, SUESC, 20211-351 Rio de Janeiro (Brazil); Alho, B. P. [Instituto de Aplicação Fernando Rodrigues da Silveira, Universidade do Estado do Rio de Janeiro, Rua Santa Alexandrina, 288, 20260-232 Rio de Janeiro (Brazil); Carvalho, G. [Laboratório Nacional de Luz Sincroton—LNLS, 13083-970 Campinas, São Paulo (Brazil); Magnus, A.

2014-10-14

We report theoretical investigations on the magnetocaloric effect, described by the magnetic entropy change in rare earth—transition metal amorphous systems. The model includes the local anisotropy on the rare earth ions in Harris-Plischke-Zuckermann assumptions. The transition metals ions are treated in terms of itinerant electron ferromagnetism and the magnetic moment of rare earth ions is coupled to the polarized d-band by a local exchange interaction. The magnetocaloric effect was calculated in DyCo{sub 3.4} system, which presents amorphous sperimagnetic configuration. The calculations predict higher refrigerant capacity in the amorphous DyCo{sub 3.4} than in DyCo{sub 2} crystal, highlighting the importance of amorphous magnetocaloric materials. Our calculation of the magnetocaloric effect in Dy{sub 70}Zr{sub 30}, which presents amorphous asperomagnetic configuration, is in good agreement with the experimental result. Furthermore, magnetic entropy changes associated with crystal-amorphous configurations change are estimated.

Fracture toughness of Dy123 low porosity bulks at liquid nitrogen temperature

International Nuclear Information System (INIS)

Murakami, A.; Otaka, K.; Miura, T.; Iwamoto, A.

2011-01-01

Fracture toughness values were measured for Dy123 bulks. Fracture toughness was improved by reducing porosity. Fracture toughness values at 77 K were higher than those at room temperature. Fracture toughness was also improved by Ag addition. In order to evaluate the fracture toughness of DyBa 2 Cu 3 O x (Dy123) low porosity bulks, bending tests of V-notched specimens cut from the bulks were carried out. Fracture toughness evaluations of a conventional Dy123 bulk which had pores were also carried out and effects of elimination of pores on the fracture toughness were investigated. Fracture toughness values at 77 K of the low porosity bulks were higher than those of the porous bulk. These fracture toughness values at 77 K were higher than the values at room temperature. Fracture toughness of the low porosity bulk was improved by Ag addition.

Recent research on the heavy transuranium elements

International Nuclear Information System (INIS)

Seaborg, G.T.

1988-09-01

This review is devoted to recent research (performed in the 1980s) on the heavy members of the group, defined as the transcurium elements (with a few references to related work on lighter elements). It covers the discovery of the three heaviest elements, the discovery of new isotopes, investigation of interesting decay properties of some previously known isotopes, investigations of some heavy ion reaction mechanisms in this region, and recent investigations of nuclear and chemical properties. It is not exhaustive in its coverage, is necessarily succinct, and inevitably places emphasis on those aspects with which the author is most familiar. 92 refs., 3 figs

Electro-magnetic properties of heavy nuclei

International Nuclear Information System (INIS)

Otsuka, Takaharu

1989-01-01

Two topics of electro-magnetic properties of heavy nuclei are discussed. The first topic is the M1 excitation from well-deformed heavy nuclei, and the other is the sudden increase of the isotope shift as a function of N in going away from the closed shell. These problems are considered in terms of the particle-number projected (Nilsson-) BCS calculation. (author)

Collinear laser spectroscopy on In isotopes from heavy ion fusion reactions

International Nuclear Information System (INIS)

Ulm, G.

1984-07-01

Indium isotopes 107-111 were produced by 16 O-fusion reactions and investigated in a collinear laser geometry. The hyperfine structure and isotopic shifts are measured and the deduced magnetic dipole moments are in agreement with shell model calculations. The nuclear charge radii are determined from the isotopic shifts. (WL)

New features in the spectrum of {sup 152}Dy

Energy Technology Data Exchange (ETDEWEB)

Galindo-Uribarri, A; Andrews, H R; Ball, G C; Radford, D C; Janzen, V P; Ward, D [Atomic Energy of Canada Ltd., Chalk River, ON (Canada). Chalk River Nuclear Labs.; Kuehner, J A; Mullins, S; Persson, L; Prevost, D; Waddington, J C [McMaster Univ., Hamilton, ON (Canada). Dept. of Physics; Drake, T E [Toronto Univ., ON (Canada). Dept. of Physics; Wyss, R [Joint Inst. for Heavy Ion Research, Oak Ridge, TN (United States)

1992-08-01

One of the most important recent developments in nuclear structure physics has been the prediction and observation of superdeformed (SD) shapes at high angular momentum in several nuclei in the rare earth region. The first experimental observation was a ridge-valley structure in a {gamma}-{gamma} coincidence matrix for the {sup 152}Dy nucleus. The ridge was found to be generated by sequences of stretched E2 transitions and corresponded to a moment of inertia J{sup (2)} of 85 {Dirac_h}{sup 2}MeV{sup -1}. Subsequently a discrete SD band was discovered in {sup 152}Dy and the lifetimes were measured. More recently the discovery of SD bands in several nuclei in the neighbourhood of {sup 152}Dy, the discovery of multiple SD bands in some nuclei, and the discovery of new SD regions at mass A {approx} 190 and A {approx} 140 have stimulated intense research activity in this area of nuclear physics. (author). 15 refs., 4 figs.

Variability of Fe isotope compositions of hydrothermal sulfides and oxidation products at mid-ocean ridges

Science.gov (United States)

Li, Xiaohu; Wang, Jianqiang; Chu, Fengyou; Wang, Hao; Li, Zhenggang; Yu, Xing; Bi, Dongwei; He, Yongsheng

2018-04-01

Significant Fe isotopic fractionation occurs during the precipitation and oxidative weathering of modern seafloor hydrothermal sulfides, which has an important impact on the cycling of Fe isotopes in the ocean. This study reports the Fe-isotope compositions of whole-rock sulfides and single-mineral pyrite collected from hydrothermal fields at the South Mid-Atlantic Ridge (SMAR) and the East Pacific Rise (EPR) and discusses the impacts of precipitation and late-stage oxidative weathering of sulfide minerals on Fe isotopic fractionation. The results show large variation in the Fe-isotope compositions of the sulfides from the different hydrothermal fields on the mid-oceanic ridges, indicating that relatively significant isotope fractionation occurs during the sulfide precipitation and oxidative weathering processes. The Fe-isotope compositions of the sulfides from the study area at the SMAR vary across a relatively small range, with an average value of 0.01‰. This Fe-isotope composition is similar to the Fe-isotope composition of mid-oceanic ridge basalt, which suggests that Fe was mainly leached from basalt. In contrast, the Fe-isotope composition of the sulfides from the study area at the EPR are significantly enriched in light Fe isotopes (average value - 1.63‰), mainly due to the kinetic fractionation during the rapid precipitation process of hydrothermal sulfide. In addition, the pyrite from different hydrothermal fields is enriched in light Fe isotopes, which is consistent with the phenomenon in which light Fe isotopes are preferentially enriched during the precipitation of pyrite. The red oxides have the heaviest Fe-isotope compositions (up to 0.80‰), indicating that heavy Fe isotopes are preferentially enriched in the oxidation product during the late-stage oxidation process. The data obtained from this study and previous studies show a significant difference between the Fe-isotope compositions of the sulfides from the SMAR and EPR. The relatively heavy

Coercivity enhancement of Dy-free Nd–Fe–B sintered magnets by intergranular adding Ho{sub 63.4}Fe{sub 36.6} alloy

Energy Technology Data Exchange (ETDEWEB)

Liang, Liping; Ma, Tianyu, E-mail: maty@zju.edu.cn; Wu, Chen; Zhang, Pei; Liu, Xiaolian; Yan, Mi, E-mail: mse_yanmi@zju.edu.cn

2016-01-01

High coercivity Nd–Fe–B sintered magnets serving in high-temperature environments always consume expensive and scarce heavy rare-earth Dy, which has simulated considerable interest to reduce Dy usage. In this work, coercivity of Dy-free magnets was investigated through intergranular adding eutectic Ho{sub 63.4}Fe{sub 36.6} powders. The coercivity increases gradually up to 4 wt% Ho{sub 63.4}Fe{sub 36.6} addition, however the remanence starts to deteriorate drastically as the addition is over 2.5 wt%. Coercivity above 18.0 kOe is obtained at the expense of a slight reduction in remanence through optimizing the addition amount and sintering conditions. The coercivity enhancement is explained through microstructural observations and elemental distribution analysis. (i) (Nd, Ho){sub 2}Fe{sub 14}B shell forms in the outer region of 2:14:1 phase grains, strengthening the local magnetic anisotropy filed, (ii) RE-rich grain boundary phase with low Fe content is thickened, weakening the magnetic coupling between adjacent 2:14:1 phase grains, and (iii) 2:14:1 phase grains are refined upon lowering sintering temperature, reducing the microstructural defects and the stray fields aroused from neighboring grains. - Highlights: • Eutectic Ho{sub 63.4}Fe{sub 36.6} powders were intergranular added to NdFeB sintered magnets. • The doped Dy-free magnet possessed coercivity of 18.0 kOe, remanence of 13.15 kGs. • (Nd, Ho){sub 2}Fe{sub 14}B shell formed in the surface of the matrix grains, increasing the H{sub A}. • Thick grain boundaries with low Fe content formed, decoupling the matrix grains. • By sintered at lower temperature, the matrix phase grains were refined.

Purification and characterization of two DyP isozymes from Thanatephorus cucumeris Dec 1 specifically expressed in an air-membrane surface bioreactor.

Science.gov (United States)

Shimokawa, Takuya; Shoda, Makoto; Sugano, Yasushi

2009-02-01

DyP isozymes (DyP2 and DyP3) from the culture fluid of the fungus Thanatephorus cucumeris Dec 1 by air-membrane surface bioreactor were purified and characterized. The characteristics of DyP2 were almost the same as those of a recombinant DyP reported previously, but different from DyP3.

Investigation of complexes with bone affinity using the In vivo generator system 166 Dy/166 Ho

International Nuclear Information System (INIS)

Pedraza L, M.

2006-01-01

The importance of this original research lies in the fact that it has proven that the [ 166 Dy]Dy/ 166 Ho-EDTMP in vivo generator system is a stable complex that can be used as a therapeutic radiopharmaceutical. Multiple myeloma and other hematological malignancies have been treated by myeloablative radiotherapy/chemotherapy and subsequent stem cell transplantation. Bone-seeking radiopharmaceuticals such as 166 Ho-DOTMP or 153 Sm-DTMP, have been proposed for delivering ablative radiation doses to marrow in multiple myeloma and other hematological malignancies or have shown excellent results in palliative bone metastasis pain therapy, respectively. As lanthanides have similar chemical characteristics the phosphonate with bone affinity (EDTMP) labeled with Dy/Ho can be used for marrow ablation while causing minimal irradiation to normal organs. This in vivo generator system has not been previously reported. The aim of this research was to label EDTMP (ethylene diamine tetramethylene phosphonate) with 166 Dy/ 166 Ho; to evaluate the in vitro and in vivo stability of both 166 Dy-EDTMP and 166 Ho-EDTMP complexes when the daughter 166 Ho is formed as a dysprosium decay product; to determine the bone marrow cytotoxic and genotoxic effect in mice and to evaluate, by histopathology, the myeloablative potential of the [ 166 Dy]Dy/ 166 Ho-EDTMP in vivo generator system. 166 Dy was obtained by neutron irradiation of enriched 164 Dy 2 O 3 in a TRIGA Mark III reactor. Labeling was carried out in an aqueous phosphate medium at pH 8.0 by addition of 166 DyCl 3 to EDTMP at a molar ratio 1:1.75, with >99 % radiochemical purity, as determined by thin-layer chromatography (TLC) and high-performance liquid chromatography (HPLC). In vitro studies demonstrated that 166 Dy/ 166 Ho-EDTMP is unstable after dilution in saline but stable in human serum with no translocation of the daughter nucleus subsequent to β decay of 166 Dy, which could release free 166 Ho 3+ . Biodistribution in mice

The effect of gamma irradiation on chitosan film dyed with malachite green

International Nuclear Information System (INIS)

Yeoh Siong Hu; Md Soot Ahmad

2009-01-01

In this research, chitosan is used as the base for a dye and the effects of γ-irradiation on the dye was researched. The dyed chitosan film of the thickness 70 μm was developed by dissolving chitosan powder in an acetic acid solution. Malachite Green dye was used as the dye and was prepared by using water as solvent. Dyed chitosan gel was the dried and small pieces of 1 x 1 cm 2 was cut out and the dyed film was analyzed using the UV-VIS spectrometer and achieved a maximum absorption at the wavelength of λ=615 nm. Using Gammacell, the film was irradiated by gamma ray with various doses ranging from 5-25 KGy. The effect of the irradiation on the dyed film was study for various factors. The effect of the dose, thickness and shelf life was studied and shows significant effect to the optical density. As the dose reaches 25 KGy, the destruction of the dye approaches 20%. (Author)

Isotopic discontinuities in ground water beneath Yucca Mountain, Nevada

International Nuclear Information System (INIS)

Stuckless, J.S.; Whelan, J.F.; Steinkampf, W.C.

1991-01-01

Analytical data for stable isotopes in ground water from beneath Yucca Mountain, when examined in map view, show areal patterns of heterogeneity that can be interpreted in terms of mixing of at least three end members. One end member must be isotopically heavy in terms of hydrogen and oxygen and have a young apparent 14 C age such as water found at the north end of Yucca Mountain beneath Fortymile Wash. A second end member must contain isotopically heavy carbon and have an old apparent 14 C age such as water from the Paleozoic aquifer. The third end member cannot be tightly defined. It must be isotopically lighter than the first with respect of hydrogen and oxygen and be intermediate to the first and second end members with respect to both apparent 14 C age and δ 13 C. The variable isotopic compositions of hydrogen and oxygen indicate that two of the end members are waters, but the variable carbon isotopic composition could represent either a third water end member or reaction of water with a carbon-bearing solids such as calcite. 15 refs., 4 figs., 1 tab

Determination of Antimicrobial Activity of the Dyed Silk Fabrics with Some Natural Dyes

OpenAIRE

ALKAN, Rezan; TORGAN, Emine; AYDIN, Canan; KARADAG, Recep

2015-01-01

In this study, silk fabric is dyed with natural indigo. Dyed silk fabric with natural indigo was cut in the 20x20 cm2 size. Excluding a fabric, all fabrics were mordanted in the same percentage with alum metal (KAl(SO4)2.12H2O). Then, silk fabrics for green color dyeing are dyed separately with weld (Reseda luteola), gall oak (Quercus infectoria Olivier) and together weld (Reseda luteola) and gall oak (Quercus infectoria) in different percentage. Antimicrobial functionality of the twenty seve...

Dy{sup 3+} ions as optical probes for studying structure of boro-tellurite glasses

Energy Technology Data Exchange (ETDEWEB)

Tuyen, Vu Phi, E-mail: vptuyen@gust-edu.vast.vn [Duytan University, K7/25 Quang Trung, Da Nang (Viet Nam); Graduate University of Science and Technology – VAST, 18 Hoang Quoc Viet, Hanoi (Viet Nam); Sengthong, Bounyavong; Quang, Vu Xuan [Duytan University, K7/25 Quang Trung, Da Nang (Viet Nam); Van Do, Phan [Thuyloi University, 175 Tay Son, Dong Da, Hanoi (Viet Nam); Van Tuyen, Ho; Xuan Hung, Le [Duytan University, K7/25 Quang Trung, Da Nang (Viet Nam); Thanh, Nguyen Trong [Institute of Materials Science – VAST, 18 Hoang Quoc Viet, Hanoi (Viet Nam); Nogami, Masayuki [Duytan University, K7/25 Quang Trung, Da Nang (Viet Nam); Toyota Physical and Chemical research Institute (Japan); Hayakawa, Tomokatsu [Nagoya Institute of Technology, Gokisocho Showaku, 466-8555 Nagoya, Aichiken (Japan); Huy, Bui The, E-mail: buithehuy.nt@gmail.com [Duytan University, K7/25 Quang Trung, Da Nang (Viet Nam); Department of Chemistry, Changwon National University, Changwon 641-773 (Korea, Republic of)

2016-10-15

Dy{sup 3+}-doped glasses with various compositions (35+x)B{sub 2}O{sub 3}+ (45−x)TeO{sub 2}+9.5ZnO+10Na{sub 2}O+0.5Dy{sub 2}O{sub 3} (x=0; 10 and 20) were prepared by a melt–quenching technique. The Dy{sup 3+} ions are used as an optical probe, of which the Judd–Ofelt parameters, the phonon-side band, and the Raman spectra were quantitatively estimated to search the change of glass structure (the change of the ratio of [BO{sub 4}] to [BO{sub 3}] units, formation of the non-bridging oxygens (NBO{sup −}), the change of [TeO{sub 3}] to [TeO{sub 4}] units) as a function of the B{sub 2}O{sub 3} content. The Ω{sub 2} and Ω{sub 6} values of Dy{sup 3+}-doped boro-tellurite samples are larger than that of Dy{sup 3+}-doped borate or tellurite sample. The CIE chromaticity color coordinates were calculated for the luminescence spectra of Dy{sup 3+} ions of the glasses with the different compositions and they were all located in the vicinity of white light center of the color coordination diagram.

Investigation of complexes with bone affinity using the In vivo generator system {sup 166} Dy/{sup 166} Ho; Investigacion de complejos con afinidad osea utilizando el Sistema de Generador in vivo {sup 166} Dy/{sup 166} Ho

Energy Technology Data Exchange (ETDEWEB)

Pedraza L, M

2006-07-01

The importance of this original research lies in the fact that it has proven that the [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP in vivo generator system is a stable complex that can be used as a therapeutic radiopharmaceutical. Multiple myeloma and other hematological malignancies have been treated by myeloablative radiotherapy/chemotherapy and subsequent stem cell transplantation. Bone-seeking radiopharmaceuticals such as {sup 166}Ho-DOTMP or {sup 153}Sm-DTMP, have been proposed for delivering ablative radiation doses to marrow in multiple myeloma and other hematological malignancies or have shown excellent results in palliative bone metastasis pain therapy, respectively. As lanthanides have similar chemical characteristics the phosphonate with bone affinity (EDTMP) labeled with Dy/Ho can be used for marrow ablation while causing minimal irradiation to normal organs. This in vivo generator system has not been previously reported. The aim of this research was to label EDTMP (ethylene diamine tetramethylene phosphonate) with {sup 166}Dy/{sup 166}Ho; to evaluate the in vitro and in vivo stability of both {sup 166}Dy-EDTMP and {sup 166}Ho-EDTMP complexes when the daughter {sup 166}Ho is formed as a dysprosium decay product; to determine the bone marrow cytotoxic and genotoxic effect in mice and to evaluate, by histopathology, the myeloablative potential of the [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP in vivo generator system. {sup 166}Dy was obtained by neutron irradiation of enriched {sup 164}Dy{sub 2}O{sub 3} in a TRIGA Mark III reactor. Labeling was carried out in an aqueous phosphate medium at pH 8.0 by addition of {sup 166}DyCl{sub 3} to EDTMP at a molar ratio 1:1.75, with >99 % radiochemical purity, as determined by thin-layer chromatography (TLC) and high-performance liquid chromatography (HPLC). In vitro studies demonstrated that {sup 166}Dy/{sup 166}Ho-EDTMP is unstable after dilution in saline but stable in human serum with no translocation of the daughter nucleus

Development of stable isotope manufacturing in Russia

International Nuclear Information System (INIS)

Pokidychev, A.; Pokidycheva, M.

1999-01-01

For the past 25 years, Russia has relied heavily on the electromagnetic separation process for the production of middle and heavy mass stable isotopes. The separation of most light isotopes had been centered in Georgia which, after the collapse of the USSR, left Russia without this capability. In the mid-1970s, development of centrifuge technology for the separation of stable isotopes was begun. Alternative techniques such as laser separation, physical-chemical methods, and ion cyclotron resonance have also been investigated. Economic considerations have played a major role in the development and current status of the stable isotope enrichment capabilities of Russia

Fuel reprocessing data validation using the isotope correlation technique

International Nuclear Information System (INIS)

Persiani, P.J.; Bucher, R.G.; Pond, R.B.; Cornella, R.J.

1990-01-01

The Isotope Correlation Technique (ICT), in conjunction with the gravimetric (Pu/U ratio) method for mass determination, provides an independent verification of the input accountancy at the dissolver or accountancy stage of the reprocessing plant. The Isotope Correlation Technique has been applied to many classes of domestic and international reactor systems (light-water, heavy-water, and graphite reactors) operating in a variety of modes (power, research, and production reactors), and for a variety of reprocessing fuel cycle management strategies. Analysis of reprocessing operations data based on isotopic correlations derived for assemblies in a PWR environment and fuel management scheme, yielded differences between the measurement-derived and ICT-derived plutonium mass determinations of (- 0.02 ± 0.23)% for the measured U-235 and (+ 0.50 ± 0.31)% for the measured Pu-239, for a core campaign. The ICT analyses has been implemented for the plutonium isotopics in a depleted uranium assembly in a heavy-water, enriched uranium system and for the uranium isotopes in the fuel assemblies in light-water, highly-enriched systems

Thermoluminescent dosemeters of CaSO4: Dy + Teflon

International Nuclear Information System (INIS)

Campos, L.L.

1989-01-01

The development of a pellet dosemeter of CaSO 4 : Dy + Teflon at the Dosimetric Materials Production Laboratory - IPEN/Brazilian CNEN-SP is presented. The pellets were produced by cold pressing and sintering a mixture of CaSO 4 : Dy and Teflon powders. The pellet characteristics from the point of view of dosimetry. A filter combination providing an energy independent response from 20 KeV to 1,25 MeV was obtained. The dosemeter consists of three pellets sealed between two thin plastic sheets and placed under plastic and lead filters. The combination of these three filters allows to determine the energy of an unknown source. (author) [pt

Tin isotope fractionation during magmatic processes and the isotope composition of the bulk silicate Earth

Science.gov (United States)

Wang, Xueying; Amet, Quentin; Fitoussi, Caroline; Bourdon, Bernard

2018-05-01

Tin is a moderately volatile element whose isotope composition can be used to investigate Earth and planet differentiation and the early history of the Solar System. Although the Sn stable isotope composition of several geological and archaeological samples has been reported, there is currently scarce information about the effect of igneous processes on Sn isotopes. In this study, high-precision Sn isotope measurements of peridotites and basalts were obtained by MC-ICP-MS with a double-spike technique. The basalt samples display small variations in δ124/116Sn ranging from -0.01 ± 0.11 to 0.27 ± 0.11‰ (2 s.d.) relative to NIST SRM 3161a standard solution, while peridotites have more dispersed and more negative δ124Sn values ranging from -1.04 ± 0.11 to -0.07 ± 0.11‰ (2 s.d.). Overall, basalts are enriched in heavy Sn isotopes relative to peridotites. In addition, δ124Sn in peridotites become more negative with increasing degrees of melt depletion. These results can be explained by different partitioning behavior of Sn4+ and Sn2+ during partial melting. Sn4+ is overall more incompatible than Sn2+ during partial melting, resulting in Sn4+-rich silicate melt and Sn2+-rich residue. As Sn4+ has been shown experimentally to be enriched in heavy isotopes relative to Sn2+, the effect of melting is to enrich residual peridotites in relatively more compatible Sn2+, which results in isotopically lighter peridotites and isotopically heavier mantle-derived melts. This picture can be disturbed partly by the effect of refertilization. Similarly, the presence of enriched components such as recycled oceanic crust or sediments could explain part of the variations in Sn isotopes in oceanic basalts. The most primitive peridotite analyzed in this study was used for estimating the Sn isotope composition of the BSE, with δ124Sn = -0.08 ± 0.11‰ (2 s.d.) relative to the Sn NIST SRM 3161a standard solution. Altogether, this suggests that Sn isotopes may be a powerful probe of

Facile synthesis, structural characterization, and photoluminescence mechanism of Dy3+ doped YVO4 and Ca2+ co-doped YVO4:Dy3+ nano-lattices

Science.gov (United States)

Dhiren Meetei, Sanoujam; Deben Singh, Mutum; Dorendrajit Singh, Shougaijam

2014-05-01

Light plays a vital role in the evolution of life. From sunlight to candle-light and then to other form of lighting devices, human beings are utilizing light since time immemorial. Lighting devices such as conventional incandescent lamp and fluorescent lamp have been replaced by Light Emitting Diodes (LEDs) for the later is cheap, durable, etc. Now-a-days, phosphor converted LEDs have been burning issues in the fabrication of lighting devices. Especially, lanthanide ion(s) doped phosphors are of great interest for the same. However, doped phosphors have a limitation of luminescence quenching, i.e., instead of increasing luminescence on increasing dopant concentration, the luminescence decreases. Therefore, it must be rectified by one or other means so as to get maximum desirable intensity for uses in display or lighting devices. In the present work, YVO4:Dy3+ and YVO4:Dy3+/Ca2+ nano-lattices are synthesized by a facile technique. Structural characterizations such as x-ray diffraction, SEM, TEM, HRTEM, and Selected Area Electron Diffraction (SAED) of the samples are reported. Photoluminescence (PL) excitation and emission, enhanced mechanism, and lifetime are thoroughly discussed. PL intensity of the quenched YVO4:Dy3+ is made increased up to 432.63% by Ca2+ co-doping. Role of the Ca2+ on the luminescence enhanced mechanism of YVO4:Dy3+/Ca2+ is elucidated.

Complexes of Sm(III) and Dy(III) with piperazines

Energy Technology Data Exchange (ETDEWEB)

Manhas, B S; Trikha, A K [Punjabi Univ., Patiala (India). Dept. of Chemistry; Singh, M [Guru Nanak Dev Univ., Amritsar (India). Dept. of Chemistry

1981-09-01

Complexes of SmCl/sub 3/, DyCl/sub 3/, Sm(NO/sub 3/)/sub 3/ and Dy(NO/sub 3/) with piperazine, N-methylpiperazine, 2-methylpiperazine, N-phenyl-piperazine and N, N'-dimethyl-piperazine have been prepared and characterized on the basis of elemental analyses, IR and electronic reflectance spectra and magnetic susceptibility measurements. IR data indicate that the ligands are coordinated in the chair conformation giving polymeric bridged complexes and that the nitrate group is bidentate. Coordination numbers from 6 to 12 are proposed for the lanthanide ions.

Process for the extraction of tritium from heavy water

International Nuclear Information System (INIS)

Dombra, A.H.

1984-01-01

The object of the invention is achieved by a process for the extraction of tritium from a liquid heavy water stream comprising: contacting the heavy water with a countercurrent gaseous deuterium stream in a column packed with a water-repellent catalyst such that tritium is transferred by isotopic exchange from the liquid heavy water stream to the gaseous deuterium stream

Production of strange clusters in relativistic heavy ion collisions

International Nuclear Information System (INIS)

Dover, C.B.; Baltz, A.J.; Pang, Yang; Schlagel, T.J.; Kahana, S.H.

1993-02-01

We address a number of issues related to the production of strangeness in high energy heavy ion collisions, including the possibility that stable states of multi-strange hyperonic or quark matter might exist, and the prospects that such objects may be created and detected in the laboratory. We make use of events generated by the cascade code ARC to estimate the rapidity distribution dN/dy of strange clusters produced in Si+Au and Au+Au collisions at AGS energies. These calculations are performed in a simple coalescence model, which yields a consistent description of the strange cluster (d, 3 HE, 3 H, 4 He) production at these energies. If a doubly strange, weakly bound ΛΛ dibaryon exists, we find that it is produced rather copiously in Au+Au collisions, with dN/dy ∼0.1 at raid-rapidity. If one adds another non-strange or strange baryon to a cluster, the production rate decreases by roughly one or two orders of magnitude, respectively. For instance, we predict that the hypernucleus ΛΛ 6 He should have dN/dy ∼5 x 10 -6 for Au+Au central collisions. It should be possible to measure the successive Λ → pπ- weak decays of this object. We comment on the possibility that conventional multi-strange hypernuclei may serve as ''doorway states'' for the production of stable configurations of strange quark matter, if such states exist

Feasibility study of electrophoresis deposition of DyF3 on Nd-Fe-B particles for coercivity enhancement

Science.gov (United States)

Kim, K. M.; Kang, M. S.; Kwon, H. W.; Lee, J. G.; Yu, J. H.

2018-05-01

Feasibility of the electrophoresis deposition (EPD) technique for homogeneous and adhesive deposition of DyF3 particles on the Nd-Fe-B-type particles was studied, and coercivity enhancement in the diffusion-treated Nd-Fe-B-type particles deposited with DyF3 by EPD was investigated. HDDR-treated Nd12.5Fe80.6B6.4Ga0.3Nb0.2 particles were deposited with DyF3 particles by EPD. More homogeneous and adhesive deposition of DyF3 particles on the surface of Nd-Fe-B particles was made by the EPD with respect to conventional dip-coating, and this led to more active and homogeneous diffusion of Dy. More profound coercivity enhancement was achieved in the diffusion-treated Nd-Fe-B-type particles deposited with DyF3 by EPD compared to dip-coated particles.

A new dyed ECE track identification method for nuclear particle detection

International Nuclear Information System (INIS)

Sohrabi, M.; Bojd, S.S.

1990-01-01

A new procedure for obtaining highly contrasted red-dyed electrochemically etched recoil tracks in polymers such as polycarbonate (PC) and CR-39 has been successfully developed for spectrophotometry as applied to neutron dosimetry. The principal rationale in this method has been the provision of highly contrasted, photon-absorbing, large, dyed recoil tracks in an unaffected bulk material. The method consists of: (a) exposing the polymer to charged particles or neutrons; (b) electrochemical etching of the tracks; (c) acid sensitization; (d) dyeing with an appropriate dye. By investigation of the type, concentration, duration and temperature of the acid and the dye, optimized values of 20% by weight acrylic acid at 75 0 C for 3.5 h for sensitization, and 3% by weight eosin bluish dye at 95 0 C for 4 h for dyeing, provided a nearly 100% dyed-track efficiency. Spectrophotometry by UV and infrared radiation track counting, and optical densitometry were applied to the dyed samples. The results have shown some promise for UV absorbance measurements in routine large-scale applications. In this paper, the results of optimization studies and preliminary application of the technique to neutron dosimetry are presented and discussed. (author)

Crystal fields in Sc, Y, and the heavy-rare-earth metals Tb, Dy, Ho, Er, Tm, and Lu

International Nuclear Information System (INIS)

Touborg, P.

1977-01-01

Experimental investigations of the magnetic poperties of dilute alloys of the rare-earth solutes Tb, Dy, Ho, Er, and Tm in the nonmagnetic hosts Lu, Y, and Sc have been performed. These measurements, which include and supplement earlier published results, have been analyzed and crystal-field parameters for all these 15 alloy systems deduced. The consistency of the parameters was confirmed by a variety of magnetic measurements, including neutron spectroscopy. Crystal-field parameters have also been derived for the ions in pure magnetic rare-earth metals and their alloys using the results for the dilute alloys supplemented with paramagnetic measurements up to high temperatures on the concentrated systems. Mean values and standard deviations of the higher-order crystal-field parameters for all Y and Lu alloys are B 40 /β = 6.8 +- 0.9 K, B 60 /γ = 13.6 +- 0.7 K, and B 66 /γ = (9.7 +- 1.1) B 60 /γ. These values: with the inaccuracies somewhat increased: are expected to be representative also for the magnetic rare-earth metals. For rare-earth ions in the Sc host the values B 40 /β = 9.9 +- 1.9 K, B 60 /γ = 19.8 +- 1.5 K, and B 66 /γ = (9.4 +- 0.9) B 60 /γ were deduced. B 20 /α is a host-sensitive parameter which has the average values of -102.7, -53.4, and 29.5 K for rare-earth ions in Y, Lu, and Sc, respectively. There is also evidence that this parameter varies with the solute. B 20 /α for ions in the pure magnetic rare-earth metals and their alloys shows a linear variation with c/a ratio characteristic of each ion. The results indicate a contribution from anisotropic exchange to the high-temperature paramagnetic anisotropy of approximately 20% for Tb, Dy, Ho, and Er, and approximately 10% for Tm

Finishing and upgrading of heavy water

International Nuclear Information System (INIS)

Butler, J.P.; Hammerli, M.

1981-01-01

This invention provides a process and apparatus for deuterium enrichment as a final stage in a heavy water plant, for continuous on-line enrichment of the heavy water in moderator and heat transfer systems in heavy water nuclear reactors, and for enrichment of hevy water that has been downgraded with natural water during the course of operating a heavy water nuclear reactor. The method comprises contacting partially-enriched heavy water feed in a catalyst column with hydrogen gas (essentially D 2 ) orginating in an electrolysis cell so as to enrich the feed water with deuterium extracted from the electrolytic hydrogen gas and passing the deuterium-enriched water to the electrolysis cell. The apparatus comprises a catalyst isotope exchange column with hydrogen gas and liquid water passing through in countercurrent isotope exchange, an electrolysis cell, a dehumidifer-scrubber; and means for passing the liquid water enriched in deuterium from the catalyst column through the dehumidifer-scrubber to the electrolysis cell, for passing the hydrogen gas evolved in the cathode side of the cell through the dehumidifier-scrubber to the catalyst column, for passing the hydrogen gas from the catalyst column to an output, for introducing an input water feed to the upper portion of the catalyst column, and for taking a product enriched in deuterium from the system. (LL)

A critical scattering study of the helical antiferromagnets Ho and Dy

International Nuclear Information System (INIS)

Gaulin, B.D.; Hagen, M.; Child, H.R.

1988-01-01

We have measured the frequency integrated magnetic critical scattering of neutrons from paramagnetic Dy and Ho. Analysis of these data show the paramagnetic to helical antiferromagnetic phase transitions are characterized by the critical exponents ν = 0.57 +- 0.05 and γ = 1.05 = +- .07 for Dy and ν = 0.57 +- .04 and γ = 1.14 = +- .10 for Ho. 3 refs., 2 figs., 1 tab

YAG:Dy – Based single white light emitting phosphor produced by solution combustion synthesis

Energy Technology Data Exchange (ETDEWEB)

Carreira, J.F.C., E-mail: correiacarreira@ua.pt; Sedrine, N. Ben; Monteiro, T.; Rino, L.

2017-03-15

Dysprosium-doped yttrium aluminum garnet (YAG:Dy) phosphor was successfully produced by a Solution Combustion Synthesis (SCS) using a mixture of two fuels (urea and glycine). The effects of Dy concentration and annealing temperature were studied by X-ray diffraction (XRD), Raman spectroscopy (RS), photoluminescence (PL) and photoluminescence excitation (PLE). X-ray diffraction results show that the phosphors are single phase YAG with crystallite size ranging from 45 to 82 nm. Raman spectroscopy corroborates these results and show that the introduction of Dy ions in the YAG lattice results in additional Raman modes. Room temperature photoluminescence results confirm the introduction of the ion in the host lattice and its optical activation for all the Dy concentrations. CIE1931 color coordinates show that the samples’ emission lays in the near white region. The highest intraionic emission intensity was achieved for a Dy concentration of 2 mol% and annealing temperature of 1400 °C. Photoluminescence excitation results show that the ions luminescence is preferential excited with 351.8 and 365.8 nm wavelength photons.

Optimizing white light luminescence in Dy3+-doped Lu3Ga5O12 nano-garnets

International Nuclear Information System (INIS)

Haritha, P.; Linganna, K.; Venkatramu, V.; Martín, I. R.; Monteseguro, V.; Rodríguez-Mendoza, U. R.; Babu, P.; León-Luis, S. F.; Jayasankar, C. K.; Lavín, V.

2014-01-01

Trivalent dysprosium-doped Lu 3 Ga 5 O 12 nano-garnets have been prepared by sol-gel method and characterized by X-ray powder diffraction, high-resolution transmission electron microscopy, dynamic light scattering, and laser excited spectroscopy. Under a cw 457 nm laser excitation, the white luminescence properties of Lu 3 Ga 5 O 12 nano-garnets have been studied as a function of the optically active Dy 3+ ion concentration and at low temperature. Decay curves for the 4 F 9/2 level of Dy 3+ ion exhibit non-exponential nature for all the Dy 3+ concentrations, which have been well-fitted to a generalized energy transfer model for a quadrupole-quadrupole interaction between Dy 3+ ions without diffusion. From these data, a simple rate-equations model can be applied to predict that intense white luminescence could be obtained from 1.8 mol% Dy 3+ ions-doped nano-garnets, which is in good agreement with experimental results. Chromaticity color coordinates and correlated color temperatures have been determined as a function of temperature and are found to be within the white light region for all Dy 3+ concentrations. These results indicate that 2.0 mol% Dy 3+ ions doped nano-garnet could be useful for white light emitting device applications

18O isotopic characterisation of non-point source contributed heavy metals (Zn and Cu) contamination of groundwater

International Nuclear Information System (INIS)

Datta, P.S.; Manjaiah, K.M.; Tyagi, S.K.

1999-01-01

In many urbanised areas, fast depletion and severe degradation of the of groundwater resource with contaminants such as nitrate, fluoride, and heavy metals is a common phenomenon, resulting in zonal disparity in fresh water availability. Therefore, for protection of groundwater from pollution and depletion, it is a matter of concern for the planners and decision makers to clearly characterise the sources of contamination and to search for an alternative approach for groundwater development and management. In this context, a new approach is presented here, based on monitoring of 18 O stable isotopic and heavy metals composition of groundwater, to clearly characterise non-point source contributed heavy metals pollution of groundwater in northern parts of Delhi area. In the investigated area, the Cu content in the groundwater ranges from 3-41 μg/l and Zn content ranges from 5-182 μg/l, showing considerable variation from location to location as well as within the small parts of a location. Wide variation in the 18 O stable isotope content of groundwater (δ value of -5.7 per mille to -8.5 per mille) is due to significant variation in the δ 18 O-contents of rainfall with space and time, as well as intensity and distribution of rainfall. Enrichment in 18 O composition with increasing Cu and Zn levels in groundwater suggest that infiltration of rain water, irrigation water and surface run-off water from the surrounding farm lands, along with agrochemicals and other salts present in the soil, to be the main processes causing groundwater contamination. The concentration of Cu and Zn in groundwater vary spatially, due to different degrees of evaporation/recharge, amounts of fertiliser applied and wastes disposed, adsorption/dispersion of species in the soils and lateral mixing of groundwater. Two opposite mechanisms adsorption and redistribution of infiltrating water along with Zn and Cu species in the soil zone are likely to affect the movement of the Zn and Cu species

The origin of volatile element depletion in early solar system material: Clues from Zn isotopes in chondrules

Science.gov (United States)

Pringle, Emily A.; Moynier, Frédéric; Beck, Pierre; Paniello, Randal; Hezel, Dominik C.

2017-06-01

Volatile lithophile elements are depleted in the different planetary materials to various degrees, but the origin of these depletions is still debated. Stable isotopes of moderately volatile elements such as Zn can be used to understand the origin of volatile element depletions. Samples with significant volatile element depletions, including the Moon and terrestrial tektites, display heavy Zn isotope compositions (i.e. enrichment of 66Zn vs. 64Zn), consistent with kinetic Zn isotope fractionation during evaporation. However, Luck et al. (2005) found a negative correlation between δ66Zn and 1/[Zn] between CI, CM, CO, and CV chondrites, opposite to what would be expected if evaporation caused the Zn abundance variations among chondrite groups. We have analyzed the Zn isotope composition of multiple samples of the major carbonaceous chondrite classes: CI (1), CM (4), CV (2), CO (4), CB (2), CH (2), CK (4), and CK/CR (1). The bulk chondrites define a negative correlation in a plot of δ66Zn vs 1/[Zn], confirming earlier results that Zn abundance variations among carbonaceous chondrites cannot be explained by evaporation. Exceptions are CB and CH chondrites, which display Zn systematics consistent with a collisional formation mechanism that created enrichment in heavy Zn isotopes relative to the trend defined by CI-CK. We further report Zn isotope analyses of chondrite components, including chondrules from Allende (CV3) and Mokoia (CV3), as well as an aliquot of Allende matrix. All chondrules are enriched in light Zn isotopes (∼500 ppm on 66Zn/64Zn) relative to the bulk, contrary to what would be expected if Zn were depleted during evaporation, on the other hand the matrix has a complementary heavy isotope composition. We report sequential leaching experiments in un-equilibrated ordinary chondrites, which show sulfides are isotopically heavy compared to silicates and the bulk meteorite by ca. +0.65 per mil on 66Zn/64Zn. We suggest isotopically heavy sulfides were

Preparation of CaSO4:Dy by precipitation method to gamma radiation dosimetry

International Nuclear Information System (INIS)

Rivera, T.; Roman, J.; Azorin, J.; Sosa, R.; Guzman, J.; Serrano, A.K.; Garcia, M.; Alarcon, G.

2010-01-01

This paper presents the results of the preparation and characterization of dysprosium-doped calcium sulfate (CaSO 4 :Dy) phosphor, which was obtained by homogeneous precipitation from calcium acetate Ca(CH 3 COO - ) 2 . Structural and morphological characteristics were studied using a scanning electronic microscope (SEM). The structure of all compounds was determined by X-ray diffraction method too. Thermoluminescence (TL) emission properties of CaSO 4 :Dy under gamma radiation effects were studied. This phosphor powder presented a TL glow curve with two peaks (Tmax) centered at around of 180 and 300 deg. C, respectively. The TL response of CaSO 4 :Dy as a function of gamma absorbed dose was linear in a wide range. Both emission and excitation spectra were also obtained. Results showed that this new preparation method of CaSO 4 :Dy TL phosphor is less expensive, cleaner and safer than the conventional preparation method.

Feasibility study of electrophoresis deposition of DyF3 on Nd-Fe-B particles for coercivity enhancement

Directory of Open Access Journals (Sweden)

K. M. Kim

2018-05-01

Full Text Available Feasibility of the electrophoresis deposition (EPD technique for homogeneous and adhesive deposition of DyF3 particles on the Nd-Fe-B-type particles was studied, and coercivity enhancement in the diffusion-treated Nd-Fe-B-type particles deposited with DyF3 by EPD was investigated. HDDR-treated Nd12.5Fe80.6B6.4Ga0.3Nb0.2 particles were deposited with DyF3 particles by EPD. More homogeneous and adhesive deposition of DyF3 particles on the surface of Nd-Fe-B particles was made by the EPD with respect to conventional dip-coating, and this led to more active and homogeneous diffusion of Dy. More profound coercivity enhancement was achieved in the diffusion-treated Nd-Fe-B-type particles deposited with DyF3 by EPD compared to dip-coated particles.

Modulating the single-molecule magnet behaviour in phenoxo-O bridged Dy2 systems via subtle structural variations

Science.gov (United States)

Wang, Wen-Min; Zhao, Xiao-Yu; Qiao, Hui; Bai, Li; Han, Hong-Fei; Fang, Ming; Wu, Zhi-Lei; Zou, Ji-Yong

2017-09-01

In search of simple approaches to rationally modulate the single-molecule magnet behaviour in polynuclear lanthanide compound, a new system containing two structurally closely related dinuclear dysprosium complexes, namely [Dy2(hfac)4L2] (1) and [Dy2(hfac)4L‧2] (2) (hfac = hexafluoroacetylacetonate, HL = 2-[4-methylaniline-imino]methyl]-8-hydroxyquinoline and HL' = 2-[(3,4-dimethylaniline)-imino]methyl]-8-hydroxyquinoline), are successfully synthesized and the structure-dependent magnetic properties are investigated. The two Dy2 compounds display only slight variations in the coordination geometries of the center Dy(III) ion but display remarkably different single-molecule magnet behaviors with the anisotropic barriers (ΔE/kB) of 9.91 K for 1 and 20.57 K for 2. The different magnetic relaxation behaviors of the two Dy2 complexes mainly originate from the different chemical environments of the central DyIII ions.

Preparation of 166 Dy/166 Ho DTPA-bis biotin as a system of In vivo generator

International Nuclear Information System (INIS)

Jimenez V, M.R.

2003-01-01

The objective of this work was to synthesize the complex 166 Dy/ 166 Ho - diethylen triamine pentaacetic-bis Biotin ( 166 Dy/ 166 Ho DTPA-bis Biotin) to evaluate its potential as a new radiopharmaceutical in directed radiotherapy. The Dysprosium-166 was obtained for neutron irradiation of 164 Dy 2 0 3 in the TRIGA Mark III reactor. The labelled was carried out in aqueous solution to p H 8.0 for addition of 166 Dy Cl 3 to the diethylen triamine pentaacetic-α, ω-bis Biotin (DTPA-bis Biotin). The radiochemical purity was determined for HPLC and ITLC. The biological integrity of the marked biotin is evaluated by the biological recognition of the avidin for HPLC - molecular exclusion with and without avidin addition. The studies of stability in vitro were made in dilutions of saline solution to 0.9% and with human serum at 37 C incubated 1 and 24 hours. The complex 166 Dy/ 166 Ho DTPA-bis Biotin was obtained with a radiochemical purity of 99.1 ± 0.6%. The biological recognition of the complex 166 Dy/ 166 Ho DTPA-bis Biotin for the avidin it doesn't affect the labelling procedure. The studies in vitro demonstrated that the 166 Dy/ 166 Ho DTPA-bis Biotin is stable after the dilution in saline solution and in human serum that there is not translocation of the one radionuclide subsequent son to the beta decay of the 166 Dy that could produce the 166 Ho 3+ liberation. The studies of Biodistribution in healthy mice demonstrated that the one complex 166 Dy/ 166 Ho DTPA-bis Biotin have a high renal distribution. In conclusion the radiolabelled biotin in this investigation has the appropriate properties to be used as an In vivo generator system stable for directed radiotherapy. (Author)

Magnetoresistance anomaly in DyFeCo thin films

International Nuclear Information System (INIS)

Wu, J. C.; Wu, C. S.; Wu, Te-ho; Chen, Bing-Mau; Shieh, Han-Ping D.

2001-01-01

Microstructured rare-earth - transition-metal DyFeCo films have been investigated using magnetoresistance and extraordinary Hall-effect measurements. The Hall loops reveal variation of coercive fields depending on the linewidth and the composition of the films. The magnetoresistance curves, with changes up to as high as 1.3%, show positive/negative magnetoresistance peaks centered on the coercive fields depending on the linewidth of the films only. The variation of the coercivity can be attributed to the magnetic moment canting between the Dy and FeCo subcomponents and the existence of the diverged magnetization on the edges, and the anomalous magnetoresistance peaks observed are discussed with the existing theories. [copyright] 2001 American Institute of Physics

Development of the web-based Spanish and Catalan versions of the Euroqol 5D-Y (EQ-5D-Y) and comparison of results with the paper version.

Science.gov (United States)

Robles, Noemí; Rajmil, Luis; Rodriguez-Arjona, Dolors; Azuara, Marta; Codina, Francisco; Raat, Hein; Ravens-Sieberer, Ulrike; Herdman, Michael

2015-06-03

The objectives of the study were to develop web-based Spanish and Catalan versions of the EQ-5D-Y, and to compare scores and psychometric properties with the paper version. Web-based and paper versions of EQ-5D-Y were included in a cross-sectional study in Palafolls (Barcelona), Spain and administered to students (n = 923) aged 8 to 18 years from 2 primary and 1 secondary school and their parents. All students completed both the web-based and paper versions during school time with an interval of at least 2 h between administrations. The order of administration was randomized. Participants completed EQ-5D-Y, a measure of mental health status (the Strengths and Difficulties Questionnaire), and sociodemographic variables using a self-administered questionnaire. Parents questionnaire included parental level of education and presence of chronic conditions in children. Missing values, and floor and ceiling effects were compared between versions. Mean score differences were computed for the visual analogue scale (VAS). Percentage of agreement, kappa index (k) and intraclass correlation coefficient (ICC) were computed to analyze the level of agreement between web-based and paper versions on EQ-5D-Y dimensions and VAS. Known groups validity was analyzed and compared between the two formats. Participation rate was 77 % (n = 715). Both formats of EQ-5D-Y showed low percentages of missing values (n = 2, and 4 to 9 for web and paper versions respectively), and a high ceiling effect by dimension (range from 79 % to 96 %). Percent agreement for EQ-5D-Y dimensions on the web and paper versions was acceptable (range 89 % to 97 %), and k ranged from 0.55 (0.48-0.61, usual activities dimension) to 0.75 (0.68-0.82, mobility dimension). Mean score difference on the VAS was 0.07, and the ICC for VAS scores on the two formats was 0.84 (0.82-0.86). Both formats showed acceptable ability to discriminate according to self-perceived health, reporting chronic conditions, and

Magnetic exchange coupling in amorphous Fe80-xDy xB20 alloys

International Nuclear Information System (INIS)

Annouar, F.; Lassri, H.; Ayadi, M.; Omri, M.; Lassri, M.; Krishnan, R.

2005-01-01

Amorphous Fe 80-x Dy x B 20 alloys have been prepared by melt spinning and their magnetic properties have been studied. The mean field theory has been used to explain the temperature dependence of the magnetization. The exchange interactions between Co-Co and Dy-Co atom pairs have been evaluated. High-field magnetization studies on samples with stoichiometry close to that of a compensated ferrimagnet show a magnetic behavior that is characteristic of a non-collinear magnetic structure of the Dy and Fe sublattices. The region of the canted moments can be described by a phase diagram in the H-T plane

Optical properties of Dy3+ doped yttrium aluminium borate

International Nuclear Information System (INIS)

Vazquez, R MartInez; Osellame, R; Marangoni, M; Ramponi, R; Dieguez, E; Ferrari, M; Mattarelli, M

2004-01-01

A Dy 3+ doped yttrium aluminium borate (Dy:YAB) crystal has been optically characterized. The refractive indices at seven different wavelengths, ranging from the visible to the near infrared (IR), have been measured and the Sellmeier curves have been calculated. The polarized optical absorption spectra have been obtained at room temperature, and the Judd-Ofelt parameters have been calculated. The lifetime of the upper laser level 4 F 9/2 has been estimated and compared with the experimental value. Evidence of high luminescence quantum efficiency of the 4 F 9/2 state in YAB is provided by measured lifetimes

Size-dependent structure and magnetic properties of DyMnO{sub 3} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Cai, Xuan; Shi, Lei, E-mail: shil@ustc.edu.cn; Zhou, Shiming; Zhao, Jiyin; Guo, Yuqiao; Wang, Cailin [Hefei National Laboratory for Physical Sciences at the Microscale, University of Science and Technology of China, Hefei, Anhui 230026 (China)

2014-09-14

The structure and magnetic properties of orthorhombic DyMnO{sub 3} nanoparticles with different particle sizes are investigated in this paper. With decreasing particle size, all the lattice parameters a, b, and c gradually decrease, whereas the orthorhombic distortion increases. Magnetic measurements reveal that the antiferromagnetic interaction of Mn ions is weakened due to the decrease in Mn-O-Mn bond angle. Above a critical field H*, DyMnO{sub 3} undergoes a field-induced metamagnetic transition at 4 K, which is related to the spin reversal of Dy moments. The critical field H* increases monotonically with size reduction, indicating an enhancement of the antiferromagnetic interaction of Dy ions due to the decreased distance between rare earth ions. The magnetization at 4 K and 5 T, i.e., M(4 K, 5 T) shows a non-monotonic variation with particle size d, i.e., M(4 K, 5 T) initially increases with size reduction but decreases again for d < 68 nm. A modified core-shell model, in which the ferromagnetic ordering (Dy magnetic structure) and antiferromagnetic ordering (Mn magnetic structure) coexist in the core, is proposed to explain this behavior.

The centenary of the discovery of isotopes

International Nuclear Information System (INIS)

Soulie, Edgar

2013-01-01

This article recalls works performed by different scientists (Marckwald and Keetman, Stromholm and Svedberg, Soddy, Thompson, Aston) which resulted in the observation and identification of the existence of isotopes. The author also recalls various works related to mechanisms of production of isotopes, the discovery of uranium fission and the principle of chain reaction. The author notably evokes French scientists involved in the development of mass spectroscopy and in the research and applications on isotopes within the CEA after the Second World War. A bibliography of article and books published by one of them, Etienne Roth, is provided. References deal with nuclear applications of chemical engineering (heavy water and its production, chemical processes in fission reactors, tritium extraction and enrichment), isotopic fractioning and physical-chemical processes, mass spectrometry and isotopic analysis, isotopic geochemistry (on 07;Earth, search for deuterium in moon rocks and their consequences), first dating and the Oklo phenomenon, radioactive dating, water and climate (isotopic hydrology, isotopes and hailstone formation, the atmosphere), and miscellaneous scientific fields (nuclear measurements and radioactivity, isotopic abundances and atomic weight, isotopic separation and use of steady isotopes)

Investigation of complexes with bone affinity using the In vivo generator system {sup 166} Dy/{sup 166} Ho; Investigacion de complejos con afinidad osea utilizando el Sistema de Generador in vivo {sup 166} Dy/{sup 166} Ho

Energy Technology Data Exchange (ETDEWEB)

Pedraza L, M

2006-07-01

The importance of this original research lies in the fact that it has proven that the [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP in vivo generator system is a stable complex that can be used as a therapeutic radiopharmaceutical. Multiple myeloma and other hematological malignancies have been treated by myeloablative radiotherapy/chemotherapy and subsequent stem cell transplantation. Bone-seeking radiopharmaceuticals such as {sup 166}Ho-DOTMP or {sup 153}Sm-DTMP, have been proposed for delivering ablative radiation doses to marrow in multiple myeloma and other hematological malignancies or have shown excellent results in palliative bone metastasis pain therapy, respectively. As lanthanides have similar chemical characteristics the phosphonate with bone affinity (EDTMP) labeled with Dy/Ho can be used for marrow ablation while causing minimal irradiation to normal organs. This in vivo generator system has not been previously reported. The aim of this research was to label EDTMP (ethylene diamine tetramethylene phosphonate) with {sup 166}Dy/{sup 166}Ho; to evaluate the in vitro and in vivo stability of both {sup 166}Dy-EDTMP and {sup 166}Ho-EDTMP complexes when the daughter {sup 166}Ho is formed as a dysprosium decay product; to determine the bone marrow cytotoxic and genotoxic effect in mice and to evaluate, by histopathology, the myeloablative potential of the [{sup 166}Dy]Dy/{sup 166}Ho-EDTMP in vivo generator system. {sup 166}Dy was obtained by neutron irradiation of enriched {sup 164}Dy{sub 2}O{sub 3} in a TRIGA Mark III reactor. Labeling was carried out in an aqueous phosphate medium at pH 8.0 by addition of {sup 166}DyCl{sub 3} to EDTMP at a molar ratio 1:1.75, with >99 % radiochemical purity, as determined by thin-layer chromatography (TLC) and high-performance liquid chromatography (HPLC). In vitro studies demonstrated that {sup 166}Dy/{sup 166}Ho-EDTMP is unstable after dilution in saline but stable in human serum with no translocation of the daughter nucleus

Study of neutron-deficient Sn isotopes

International Nuclear Information System (INIS)

Auger, G.

1982-05-01

The formation of neutron deficient nuclei by heavy ion reactions is investigated. The experimental technique is presented, and the results obtained concerning Sn et In isotopes reported: first excited states of 106 Sn, high spin states in 107 Sn and 107 In; Yrast levels of 106 Sn, 107 Sn, 108 Sn; study of neutron deficient Sn and In isotopes formed by the desintegration of the compound nucleus 112 Xe. All these results are discussed [fr

PTFE Additive and Re-annealing Effect on Thermoluminescence Response of CaSO4:Dy Derived from Co-precipitation Method

Science.gov (United States)

Nuraeni, Nunung; Dwi Septianto, Ricky; Iskandar, Ferry; Haryanto, Freddy; Waris, Abdul; Hiswara, Eri

2017-07-01

Effect of re-annealing treatment in thermoluminescence response of thermoluminescent dosimeter (TLD) CaSO4:Dy and CaSO4:Dy with PTFE (Polytetrafluoroethylene) addition was investigated. CaSO4:Dy was prepared by a co-precipitation method. The PTFE was added before re-annealing treatment which the mass ratio of CaSO4:Dy and PTFE was fixed to 2:3. The re-annealing treatments of the samples were done at temperature 700 °C for 1 hr. The obtained samples were characterized using a Fourier-transform infrared (FTIR) and X-ray diffraction (XRD) to observe the molecule bonding in sample and crystal properties, respectively. From the experimental results, it was observed that the thermoluminescence intensity of CaSO4:Dy, CaSO4:Dy re-annealed at 700 °C, and CaSO4:Dy + PTFE re-annealed at 700 °C are 57.03, 75.15, and 1191.11 nC, respectively. The intensity of 700 °C-re-annealed CaSO4:Dy increased significantly after PTFE addition.

Studies on the adsorption behaviour of heavy rare earths with a strong cation exchanger DOWEX 50W-2X8

International Nuclear Information System (INIS)

Vijayalakshmi, R.; Singh, D.K.; Anitha, M.; Kotekar, M.K.; Dasgupta, K.; Singh, H.

2014-01-01

Rare earths have been a very fascinating area of research since long due to its wide applicability's in many field including superconductors, lasers, phosphors, medical, electronics, magnet, optics etc. Separation of rare earths is a challenging task and over the years many separation schemes based on solvent extraction, ion exchange, membrane etc have been developed and deployed. In the present work, we have investigated the adsorption behavior of heavy rare earths from a crude concentrate analyzing ∼ 80% Y 2 O 3 , ∼12% Dy 2 O 3 , ∼4% Er 2 O 3 etc., with a strong cationic exchanger namely Dowex 50W-2X8 in order to separate them in pure form. To start with, Y was selected as a representative of heavy rare earths and the conditions were optimized in batch experiments and later were applied to the feed solution containing Dy, Er, Ho etc. in a column study. Effects of experimental variables such as contact time, pH, weight of resin, concentration of the feed metal, temperature, desorption agents, on adsorption of Y was studied

Utilization of stable isotopes for characterizing an underground gas generator; Utilisation des isotopes stables pour caracteriser un gazogene souterrain

Energy Technology Data Exchange (ETDEWEB)

Pirard, J P; Antenucci, D; Renard, X [Liege Univ. (Belgium); Letolle, R [Paris-6 Univ., 75 (France)

1994-12-31

The principles of isotopic exchange and isotope ratio result interpretation are first reviewed; then, in the framework of an underground coal gasification project in Belgium, experiments and modelling of the underground gas generator have been carried out: isotopic abundances of carbon, hydrogen and oxygen have been measured in the gasifying agent (O{sub 2}, H{sub 2}O) and in the effluent (CO{sub 2}, CO, H{sub 2}, H{sub 2}O, CH{sub 4}, O{sub 2}, heavy oils and various organic and mineral substances). Gasification kinetics and temperatures have been evaluated and isotope application to thermometry is discussed. 1 fig., 9 refs.

Multi-element isotope dilution analyses using ICP-MS

International Nuclear Information System (INIS)

Volpe, A.M.

1996-01-01

Presently, 37 elements ranging from light (Li,B) through transition metals, noble, rare earth and heavy elements, to actinides and transuranics (Pu, Am, Cm) are measured by isotope dilution at Lawrence Livermore National Laboratory. Projects range from geological and hydrological to biological. The research goal is to measure accurately many elements present in diverse matrices at trace (ppb) levels using isotope dilution methods. Major advantages of isotope dilution methods are accuracy, elimination of ion intensity calibration, and quantitation for samples that require chemical separation. Accuracy depends on tracer isotope calibration, tracer-sample isotopic equilibration, and appropriate background, isobaric and mass bias corrections. Propagation of isotope ratio error due to improper tracer isotope addition is a major concern with multi-element analyses when abundances vary widely. 11 refs., 3 figs

Electrical Conductivity of Molten DyCl3-NaCl and DyCl3-KCl Systems: An Approach to Structural Interpretations of Rare Earth Chloride Melts

Science.gov (United States)

Iwadate, Yasuhiko; Ohkubo, Takahiro

2017-11-01

Electrical conductivities (κs) of molten DyCl3-NaCl and DyCl3-KCl systems were estimated by measuring the impedances of each mixture melt at any temperature and/or frequency. The molar volumes (Vms) were measured by dilatometry and represented as a polynomial empirical equation of temperature and composition. Due to both the properties, the molar conductivities (Λms) were calculated and their temperature and/or composition dependences were discussed from the standpoint of structural features as well. The κs increased curvilinearly with increasing temperature across the whole composition ranges. This trend was also applied to the Λms which was fitted by an Arrhenius-type equation. The relationship of Λms with melt composition was studied and the Λms were found to decrease with increasing composition of DyCl3. These findings were interpreted based on the results of structural science so far reported, and finally, the relationship between Λms and the structures of pure rare earth chloride melts was discussed.

Preparation of {sup 166} Dy/{sup 166} Ho DTPA-bis biotin as a system of In vivo generator; Preparacion de {sup 166} Dy/{sup 166} Ho DTPA-bis biotina como un sistema de generador In vivo

Energy Technology Data Exchange (ETDEWEB)

Jimenez V, M.R

2003-07-01

The objective of this work was to synthesize the complex {sup 166} Dy/{sup 166} Ho - diethylen triamine pentaacetic-bis Biotin ({sup 166} Dy/{sup 166} Ho DTPA-bis Biotin) to evaluate its potential as a new radiopharmaceutical in directed radiotherapy. The Dysprosium-166 was obtained for neutron irradiation of {sup 164} Dy{sub 2}0{sub 3} in the TRIGA Mark III reactor. The labelled was carried out in aqueous solution to p H 8.0 for addition of {sup 166} Dy Cl{sub 3} to the diethylen triamine pentaacetic-{alpha}, {omega}-bis Biotin (DTPA-bis Biotin). The radiochemical purity was determined for HPLC and ITLC. The biological integrity of the marked biotin is evaluated by the biological recognition of the avidin for HPLC - molecular exclusion with and without avidin addition. The studies of stability in vitro were made in dilutions of saline solution to 0.9% and with human serum at 37 C incubated 1 and 24 hours. The complex {sup 166} Dy/{sup 166} Ho DTPA-bis Biotin was obtained with a radiochemical purity of 99.1 {+-} 0.6%. The biological recognition of the complex {sup 166} Dy/{sup 166} Ho DTPA-bis Biotin for the avidin it doesn't affect the labelling procedure. The studies in vitro demonstrated that the {sup 166} Dy/{sup 166} Ho DTPA-bis Biotin is stable after the dilution in saline solution and in human serum that there is not translocation of the one radionuclide subsequent son to the beta decay of the {sup 166} Dy that could produce the {sup 166} Ho{sup 3+} liberation. The studies of Biodistribution in healthy mice demonstrated that the one complex {sup 166} Dy/{sup 166} Ho DTPA-bis Biotin have a high renal distribution. In conclusion the radiolabelled biotin in this investigation has the appropriate properties to be used as an In vivo generator system stable for directed radiotherapy. (Author)

Preparation of {sup 166} Dy/{sup 166} Ho DTPA-bis biotin as a system of In vivo generator; Preparacion de {sup 166} Dy/{sup 166} Ho DTPA-bis biotina como un sistema de generador In vivo

Energy Technology Data Exchange (ETDEWEB)

Jimenez V, M R

2003-07-01

The objective of this work was to synthesize the complex {sup 166} Dy/{sup 166} Ho - diethylen triamine pentaacetic-bis Biotin ({sup 166} Dy/{sup 166} Ho DTPA-bis Biotin) to evaluate its potential as a new radiopharmaceutical in directed radiotherapy. The Dysprosium-166 was obtained for neutron irradiation of {sup 164} Dy{sub 2}0{sub 3} in the TRIGA Mark III reactor. The labelled was carried out in aqueous solution to p H 8.0 for addition of {sup 166} Dy Cl{sub 3} to the diethylen triamine pentaacetic-{alpha}, {omega}-bis Biotin (DTPA-bis Biotin). The radiochemical purity was determined for HPLC and ITLC. The biological integrity of the marked biotin is evaluated by the biological recognition of the avidin for HPLC - molecular exclusion with and without avidin addition. The studies of stability in vitro were made in dilutions of saline solution to 0.9% and with human serum at 37 C incubated 1 and 24 hours. The complex {sup 166} Dy/{sup 166} Ho DTPA-bis Biotin was obtained with a radiochemical purity of 99.1 {+-} 0.6%. The biological recognition of the complex {sup 166} Dy/{sup 166} Ho DTPA-bis Biotin for the avidin it doesn't affect the labelling procedure. The studies in vitro demonstrated that the {sup 166} Dy/{sup 166} Ho DTPA-bis Biotin is stable after the dilution in saline solution and in human serum that there is not translocation of the one radionuclide subsequent son to the beta decay of the {sup 166} Dy that could produce the {sup 166} Ho{sup 3+} liberation. The studies of Biodistribution in healthy mice demonstrated that the one complex {sup 166} Dy/{sup 166} Ho DTPA-bis Biotin have a high renal distribution. In conclusion the radiolabelled biotin in this investigation has the appropriate properties to be used as an In vivo generator system stable for directed radiotherapy. (Author)

Eu-, Tb-, and Dy-Doped Oxyfluoride Silicate Glasses for LED Applications

DEFF Research Database (Denmark)

Zhu, C.F.; Wang, J.; Zhang, M.M.

2014-01-01

Luminescence glass is a potential candidate for the light-emitting diodes (LEDs) applications. Here, we study the structural and optical properties of the Eu-, Tb-, and Dy-doped oxyfluoride silicate glasses for LEDs by means of X-ray diffraction, photoluminescence spectra, Commission Internationale...... de L’Eclairage (CIE) chromaticity coordinates, and correlated color temperatures (CCTs). The results show that the white light emission can be achieved in Eu/Tb/Dy codoped oxyfluoride silicate glasses under excitation by near-ultraviolet light due to the simultaneous generation of blue, green, yellow......, and red-light wavelengths from Tb, Dy, and Eu ions. The optical performances can be tuned by varying the glass composition and excitation wavelength. Furthermore, we observed a remarkable emission spectral change for the Tb3+ single-doped oxyfluoride silicate glasses. The 5D3 emission of Tb3+ can...

Judd-Ofelt Analysis of Dy3+-Activated Aluminosilicate Glasses Prepared by Sol-Gel Method

Science.gov (United States)

Sengthong, Buonyavong; Van Tuyen, Ho; An, Nguyen Thi Thai; Van Do, Phan; Hai, Nguyen Thi Quy; Chau, Pham Thi Minh; Quang, Vu Xuan

2018-04-01

Aluminosilicate (AS) glasses doped with different Dy3+ concentrations were synthesized via sol-gel method. Absorption, photoluminescence spectra and lifetime of this material have been studied. From analytical results of absorption spectra, the Judd-Ofelt (JO) parameters of prepared samples have been determined. These JO parameters combined with photoluminescence spectra have been used to evaluate transition probabilities ( A R), branching ratios ( β) and the calculated oscillator strengths of AS:Dy3+ glasses. The radiative branching ratio of 4F9/2 → 6H13/2 transition has a minimum value at 62.2% for β R which predicts that this transition in AS:Dy3+ glasses can give rise to lasing action. JO parameters show that the Ω2 increases with the increasing of Dy3+ ion concentration due to the increased polarizability of the average coordination medium and decreased average symmetry.

High-efficient, bicolor-emitting GdVO_4:Dy"3"+ phosphor under near ultraviolet excitation

International Nuclear Information System (INIS)

Lu, Jinjin; Zhou, Jia; Jia, Huayu; Tian, Yue

2015-01-01

Bicolor emitting GdVO_4:Dy"3"+ phosphor with short columniation-shape was prepared via a simple co-precipitation process. The optimal doping concentration for obtaining maximal luminescent intensity was confirmed to be 0.3 mol% and the electric dipole–dipole interaction is responsible for concentration quenching of Dy"3"+ emission in GdVO_4 phosphor. In order to evaluate the luminescent performance of as-prepared phosphor, the luminescent efficiency and color coordinates were studied. The results show that luminescent efficiency of this phosphor is very high under near UV excitation and twice times higher than commercial Y_2O_2S:Eu"3"+ phosphor. In addition, the color coordinates for optimal Dy"3"+ concentration are (0.339, 0.379), which are close to equal energy point. Therefore, the GdVO_4:Dy"3"+ phosphor may have potential application for solid state lighting.

2.4 μm diode-pumped Dy2+:CaF2 laser

Science.gov (United States)

Švejkar, Richard; Papashvili, Alexander G.; Šulc, Jan; Němec, Michal; Jelínková, Helena; Doroshenko, Maxim E.; Batygov, Sergei H.; Osiko, Vyacheslav V.

2018-01-01

In this work, a cryogenic cooled, longitudinal diode-pumped Dy2+ :CaF2 laser was investigated for the first time. The temperature dependence of the spectroscopy and the laser properties of Dy2+ :CaF2 are presented. The tested Dy2+ :CaF2 crystal was a longitudinal pump in a near-IR region (926 nm) by laser diode radiation. The maximal mean output power and slope efficiency at 78 K during the pulse regime of the laser were 57.5 mW and 7%, respectively. Furthermore, the CW regime was successfully tested and a maximum output power of 0.37 W was obtained for the absorbed pumping power 5.7 W. The emission laser wavelength was 2367 nm.

Safety system in a heavy water detritiation plant

International Nuclear Information System (INIS)

Balteanu, O.; Stefan, I.; Retevoi, C.

2003-01-01

In a CANDU 6 type reactor a quantity of 55·10 15 Bq/year of tritium is generated, 95% being in the D 2 O moderator which can achieve a radioactivity of 2.5-3.5·10 12 Bq/kg. Tritium in heavy water contributes with 30-50% to the doses received by operation personnel and up to 20% to the radioactivity released in the environment. The large quantity of heavy water used in this type of reactors (500 tones) make storage very difficult, especially for environment. The extraction of tritium from tritiated heavy water of CANDU reactors solve the following problems: the radiation level in the operation area, the costs of maintenance and repair reduction due to reduction of personnel protection measures, the increase of NPP utilisation factor by shutdown time reduction for maintenance and repair, use the extracted tritium for fusion reactors and not for the last, lower costs and risk for storage heavy water waste. Heavy water detritiation methods, which currently are used in the industrial or experimental plant, are based on catalytic isotope exchange or electrolysis followed cryogenic distillation or permeation. The technology developed at Institute of Cryogenics and Isotope Separation is based upon catalytic exchange between tritiated water and deuterium, followed by cryogenic distillation of hydrogen isotopes. The nature of the fluids that are processed in detritiation requires the operation of the plant in safety conditions. The paper presents the safety system solution chose in order to solve this task, as well as a simulation of an incident and safety system response. The application software is using LabView platform that is specialised on control and factory automation applications. (author)

Evolution of the orbitals Dy-4f in the DyB2 compound using the LDA, PBE approximations, and the PBE0 hybrid functional

Science.gov (United States)

Rasero Causil, Diego; Ortega López, César; Espitia Rico, Miguel

2018-04-01

Computational calculations of total energy based on density functional theory were used to investigate the structural, electronic, and magnetic properties of the DyB2 compounds in the hexagonal structure. The calculations were carried out by means of the full-potential linearized augmented plane wave (FP-LAPW) method, employing the computational Wien2k package. The local density approximation (LDA) and the generalized gradient approximation (GGA) were used for the electron-electron interactions. Additionally, we used the functional hybrid PBE0 for a better description the electronic and magnetic properties, because the DyB2 compound is a strongly-correlated system. We found that the calculated lattice constant agrees well with the values reported theoretically and experimentally. The density of states (DOS) calculation shows that the compound exhibits a metallic behavior and has magnetic properties, with a total magnetic moment of 5.47 μ0/cell determined mainly by the 4f states of the rare earth elements. The functional PBE0 shows a strong localization of the Dy-4f orbitals.

Synthesis of CaF2: dy for thermoluminescent dosimetry

International Nuclear Information System (INIS)

Yamato, M.E.P.; Vasconcelos, D.A.A. de; Asfora, V.K.; Khoury, H.J.; Santos, R.A.; Barros, V.S.M.

2015-01-01

Calcium Fluoride doped with dysprosium is a known thermoluminescent material for applications that require highly sensitive dosimeters. Research in novel methods such as Combustion Synthesis (CS) has been ongoing for several years at the University of Pernambuco. The method uses the heat of the oxi-redox reaction a between nitrate and a fuel. This work presents results of CaF 2 :Dy produced by combustion synthesis under different fabrication conditions. Samples were prepared by mixing stoichiometric amounts of calcium nitrate, urea and ammonium nitrate in a beaker under vigorous stirring. The resulting gel was transferred to a pre-heated muffle furnace were the combustion reaction occurred after a few minutes. For comparison, a variation of the production method with the same amounts of nitrate, ammonium fluoride and dopant, but without using the fuel was prepared. For both methods the resulting powder was pelleted and irradiated with Co-60 gamma radiation. The reproducibility and sensitivity for gamma dose irradiation was tested and results showed that optimum TL sample reproducibility was without the urea as fuel. Samples were then prepared with 0.05, 0.10, 0.15 and 0.20 mol% Dy concentration. The highest TL sensitivity was found for samples with 0.15 mol% Dy and sintered at 400 deg C for 3.5 h in air. The TL emission spectra, obtained using a Hammamatsu optical spectrometer, was comparable with commercial CaF 2 :Dy. Thermoluminescence was measured in a Harshaw-Bicron 3500 TL Reader. The glow curve showed stable dosimetric peaks at around 200, 235 and 300 deg C were a linear dose response curve was obtained for the range 100 mGy to 1000 mGy. (author)

Large-scale micromagnetic simulation of Nd-Fe-B sintered magnets with Dy-rich shell structures

Directory of Open Access Journals (Sweden)

T. Oikawa

2016-05-01

Full Text Available Large-scale micromagnetic simulations have been performed using the energy minimization method on a model with structural features similar to those of Dy grain boundary diffusion (GBD-processed sintered magnets. Coercivity increases as a linear function of the anisotropy field of the Dy-rich shell, which is independent of Dy composition in the core as long as the shell thickness is greater than about 15 nm. This result shows that the Dy contained in the initial sintered magnets prior to the GBD process is not essential for enhancing coercivity. Magnetization reversal patterns indicate that coercivity is strongly influenced by domain wall pinning at the grain boundary. This observation is found to be consistent with the one-dimensional pinning theory.

Magnetic hyperfine fields in Dy/sub 1-x/Y/sub x/Al2

International Nuclear Information System (INIS)

Hessel, A.; Kalvius, G.M.; Shenoy, G.K.; Zinn, W.; Wiedemann, W.

1982-01-01

161 Dy Moessbauer spectroscopy was carried out at 4.2 K on Dy/sub 1-x/Y/sub x/Al 2 for 0 less than or equal to x less than or equal to 0.6. For x=0 we find B=580 T and f/sub Q/=2810 MHz, close to free-ion values. For x > 0 both B and f/sub Q/ decrease weakly. We obtain (δB)/sub n/ = -14 T, (δf/sub Q/)/sub n/ = -110 MHz and (δB)/sub nn/ = + 1.6 T, (δf/sub Q/)/sub nn/ = +4 MHz per replaced nearest and next-nearest Dy 3 + neighbor, respectively

Epitaxial growth and new phase of single crystal Dy by molecular beam epitaxy

International Nuclear Information System (INIS)

Yang, Kai-Yueh; Homma, Hitoshi; Schuller, I.K.

1987-09-01

We have grown two novel epitaxial phases of dysprosium (Dy) on vanadium (V) by molecular beam epitaxy technique. Surface and bulk structures are studied by in-situ reflection high energy electron diffraction (RHEED) and x-ray diffraction techniques. The new hcp phases are ∼4% expanded uniformly in-plane (0001), and ∼9% and ∼4% expanded out of plane along the c-axes for non-interrupted and interrupted deposition case, respectively. We also observed (2 x 2), (3 x 3), and (4 x 4) Dy surface reconstruction patterns and a series of transitions as the Dy film thickness increases. 12 refs., 3 figs

Energy spectrum of CsDy(MoO/sub 4/)/sub 2/ in the vicinity of the structural phase transition

Energy Technology Data Exchange (ETDEWEB)

Khats' ko, E N; Chernyj, A S [AN Ukrainskoj SSR, Kharkov. Fiziko-Tekhnicheskij Inst. Nizkikh Temperatur

1981-08-01

The magnetic susceptibilities of CsDy(MoO/sub 4/)/sub 2/ and CsDy(MoO/sub 4/)/sub 2/+10%Eu/sup 3 +/ were measured in the temperature range 4 to 70 K and the frequency range 200 Hz to 20 MHz. The observed spin-lattice relaxation of the Dy/sup 3 +/ ion is found to be exponential with the relaxation time as a function of temperature tau/sup -1/=A exp (-..delta../kT) with ..delta..=105+-20 and 250+-40 cm/sup -1/ for CsDy(MoO/sub 4/)/sub 2/ in ranges 10-20 K and 20-38 K, respectively, and ..delta..=22.4+-5 cm for C=sDy(MoO/sub 4/)/sub 2/+10%Eu/sup 3 +/. The energies ..delta..105+-20 and 250 -40cm/sup -1/ are suggested to correspond to the first and second excited levels of Dy/sup 3 +/ in the low temperature phase of CsDy(MoO/sub 4/)/sub 2/, and ..delta..=22.4+-5 cm/sup -1/ to the first excited level of Dy/sup 3 +/ in the high temperature phase of the compound.

Experimental study of hydrogen isotopes storage on titanium bed

International Nuclear Information System (INIS)

Vasut, Felicia; Zamfirache, Marius; Bornea, Anisia; Pearsica, Claudia; Bidica, Nicolae

2002-01-01

As known, the Nuclear Power Plant Cernavoda equipped with a Canadian reactor, of CANDU type, is the most powerful tritium source from Europe. On long term, due to a 6·10 16 Bq/year, Cernavoda area will be contaminated due to the increasing tritium quantity. Also, the continuous contamination of heavy water from the reactor, induces a reduction of moderation's capacity. Therefore, one considers that it is improperly to use heavy water if its activity level is higher than 40 Ci/kg in the moderator and 2 Ci/kg in the cooling fluid. For these reasons, we have developed a detritiation technology, based on catalytic isotopic exchange and cryogenic distillation. Tritium will be removed from the tritiated heavy water, so it appears the necessity of storage of tritium in a special vessel that can provide a high level of protection and safety of environment and personal. There several metals were tested as storage beds for hydrogen isotopes. One of the reference materials used for storage of hydrogen isotopes is uranium, a material with a great storage capacity, but unfortunately it is a radioactive metal and also can react with the impurities from the stored gas. Other metals and alloys as ZrCo, Ti, FeTi are also adequate as storage beds at normal temperature. The paper presents studies about the reaction between hydrogen and titanium used as storage bed for the hydrogen isotopes resulted after the detritiation of tritiated heavy water. The experiments that were carried out used protium and mixture of deuterium and protium at different storage parameters as process gas. (authors)

Statistical γ-ray multiplicity distributions in Dy and Yb nuclei

International Nuclear Information System (INIS)

Tveter, T.S.; Bergholt, L.; Guttormsen, M.; Rekstad, J.

1994-03-01

The statistical γ-ray multiplicity distributions following the reactions 163 Dy( 3 He,αxn) 162-x Dy and 173 Yb( 3 He,αxn) 172-x Yb have been studied. The mean value and standard deviation have been extracted as functions of excitation energy. The method is based on the probability distribution of k-fold events, where an α-particle is observed in coincidence with signals in k γ-ray detectors. Techniques for isolating statistical γ-rays and subtracting random background, cross-talk and neutron contributions are discussed. 22 refs., 10 figs., 3 tabs

Multiple stable isotope fronts during non-isothermal fluid flow

Science.gov (United States)

Fekete, Szandra; Weis, Philipp; Scott, Samuel; Driesner, Thomas

2018-02-01

Stable isotope signatures of oxygen, hydrogen and other elements in minerals from hydrothermal veins and metasomatized host rocks are widely used to investigate fluid sources and paths. Previous theoretical studies mostly focused on analyzing stable isotope fronts developing during single-phase, isothermal fluid flow. In this study, numerical simulations were performed to assess how temperature changes, transport phenomena, kinetic vs. equilibrium isotope exchange, and isotopic source signals determine mineral oxygen isotopic compositions during fluid-rock interaction. The simulations focus on one-dimensional scenarios, with non-isothermal single- and two-phase fluid flow, and include the effects of quartz precipitation and dissolution. If isotope exchange between fluid and mineral is fast, a previously unrecognized, significant enrichment in heavy oxygen isotopes of fluids and minerals occurs at the thermal front. The maximum enrichment depends on the initial isotopic composition of fluid and mineral, the fluid-rock ratio and the maximum change in temperature, but is independent of the isotopic composition of the incoming fluid. This thermally induced isotope front propagates faster than the signal related to the initial isotopic composition of the incoming fluid, which forms a trailing front behind the zone of transient heavy oxygen isotope enrichment. Temperature-dependent kinetic rates of isotope exchange between fluid and rock strongly influence the degree of enrichment at the thermal front. In systems where initial isotope values of fluids and rocks are far from equilibrium and isotope fractionation is controlled by kinetics, the temperature increase accelerates the approach of the fluid to equilibrium conditions with the host rock. Consequently, the increase at the thermal front can be less dominant and can even generate fluid values below the initial isotopic composition of the input fluid. As kinetics limit the degree of isotope exchange, a third front may

Environmental monitoring by CaSO4:Dy TL dosimeters

International Nuclear Information System (INIS)

Deme, S.; Szabo, P.P.

1975-12-01

The thermoluminescent dosimeters of high sensitivity are useful for monitoring the area near nuclear installations. CaSO 4 :Dy TL dosimeters have high sensitivity and low fading so that by means of them the dose from the background can be measured with an accuracy of 10-20%. An increase of 2 mR in the background can be observed and doses as high as 1000R can be registered with an accuracy of 5%. The measuring method and results are reported here. For two years these CaSO 4 :Dy dosimeters have been successfully used at the site of the Central Research Institute for Physics. (K.A.)

Dielectron and heavy-quark production in inelastic and high-multiplicity proton-proton collisions at $\\sqrt{s} = 13$ TeV

CERN Document Server

Acharya, Shreyasi; The ALICE collaboration; Adamova, Dagmar; Adolfsson, Jonatan; Aggarwal, Madan Mohan; Aglieri Rinella, Gianluca; Agnello, Michelangelo; Agrawal, Neelima; Ahammed, Zubayer; Ahn, Sang Un; Aiola, Salvatore; Akindinov, Alexander; Al-turany, Mohammad; Alam, Sk Noor; Silva De Albuquerque, Danilo; Aleksandrov, Dmitry; Alessandro, Bruno; Alfaro Molina, Jose Ruben; Ali, Yasir; Alici, Andrea; Alkin, Anton; Alme, Johan; Alt, Torsten; Altenkamper, Lucas; Altsybeev, Igor; Anaam, Mustafa Naji; Andrei, Cristian; Andreou, Dimitra; Andrews, Harry Arthur; Andronic, Anton; Angeletti, Massimo; Anguelov, Venelin; Anson, Christopher Daniel; Anticic, Tome; Antinori, Federico; Antonioli, Pietro; Anwar, Rafay; Apadula, Nicole; Aphecetche, Laurent Bernard; Appelshaeuser, Harald; Arcelli, Silvia; Arnaldi, Roberta; Arnold, Oliver Werner; Arsene, Ionut Cristian; Arslandok, Mesut; Augustinus, Andre; Averbeck, Ralf Peter; Azmi, Mohd Danish; Badala, Angela; Baek, Yong Wook; Bagnasco, Stefano; Bailhache, Raphaelle Marie; Bala, Renu; Baldisseri, Alberto; Ball, Markus; Baral, Rama Chandra; Barbano, Anastasia Maria; Barbera, Roberto; Barile, Francesco; Barioglio, Luca; Barnafoldi, Gergely Gabor; Barnby, Lee Stuart; Ramillien Barret, Valerie; Bartalini, Paolo; Barth, Klaus; Bartsch, Esther; Bastid, Nicole; Basu, Sumit; Batigne, Guillaume; Batyunya, Boris; Batzing, Paul Christoph; Bazo Alba, Jose Luis; Bearden, Ian Gardner; Beck, Hans; Bedda, Cristina; Behera, Nirbhay Kumar; Belikov, Iouri; Bellini, Francesca; Bello Martinez, Hector; Bellwied, Rene; Espinoza Beltran, Lucina Gabriela; Belyaev, Vladimir; Bencedi, Gyula; Beole, Stefania; Bercuci, Alexandru; Berdnikov, Yaroslav; Berenyi, Daniel; Bertens, Redmer Alexander; Berzano, Dario; Betev, Latchezar; Bhaduri, Partha Pratim; Bhasin, Anju; Bhat, Inayat Rasool; Bhatt, Himani; Bhattacharjee, Buddhadeb; Bhom, Jihyun; Bianchi, Antonio; Bianchi, Livio; Bianchi, Nicola; Bielcik, Jaroslav; Bielcikova, Jana; Bilandzic, Ante; Biro, Gabor; Biswas, Rathijit; Biswas, Saikat; Blair, Justin Thomas; Blau, Dmitry; Blume, Christoph; Boca, Gianluigi; Bock, Friederike; Bogdanov, Alexey; Boldizsar, Laszlo; Bombara, Marek; Bonomi, Germano; Bonora, Matthias; Borel, Herve; Borissov, Alexander; Borri, Marcello; Botta, Elena; Bourjau, Christian; Bratrud, Lars; Braun-munzinger, Peter; Bregant, Marco; Broker, Theo Alexander; Broz, Michal; Brucken, Erik Jens; Bruna, Elena; Bruno, Giuseppe Eugenio; Budnikov, Dmitry; Buesching, Henner; Bufalino, Stefania; Buhler, Paul; Buncic, Predrag; Busch, Oliver; Buthelezi, Edith Zinhle; Bashir Butt, Jamila; Buxton, Jesse Thomas; Cabala, Jan; Caffarri, Davide; Caines, Helen Louise; Caliva, Alberto; Calvo Villar, Ernesto; Soto Camacho, Rabi; Camerini, Paolo; Capon, Aaron Allan; Carena, Francesco; Carena, Wisla; Carnesecchi, Francesca; Castillo Castellanos, Javier Ernesto; Castro, Andrew John; Casula, Ester Anna Rita; Ceballos Sanchez, Cesar; Chandra, Sinjini; Chang, Beomsu; Chang, Wan; Chapeland, Sylvain; Chartier, Marielle; Chattopadhyay, Subhasis; Chattopadhyay, Sukalyan; Chauvin, Alex; Cheshkov, Cvetan Valeriev; Cheynis, Brigitte; Chibante Barroso, Vasco Miguel; Dobrigkeit Chinellato, David; Cho, Soyeon; Chochula, Peter; Chowdhury, Tasnuva; Christakoglou, Panagiotis; Christensen, Christian Holm; Christiansen, Peter; Chujo, Tatsuya; Chung, Suh-urk; Cicalo, Corrado; Cifarelli, Luisa; Cindolo, Federico; Cleymans, Jean Willy Andre; Colamaria, Fabio Filippo; Colella, Domenico; Collu, Alberto; Colocci, Manuel; Concas, Matteo; Conesa Balbastre, Gustavo; Conesa Del Valle, Zaida; Contreras Nuno, Jesus Guillermo; Cormier, Thomas Michael; Corrales Morales, Yasser; Cortese, Pietro; Cosentino, Mauro Rogerio; Costa, Filippo; Costanza, Susanna; Crkovska, Jana; Crochet, Philippe; Cuautle Flores, Eleazar; Cunqueiro Mendez, Leticia; Dahms, Torsten; Dainese, Andrea; Dani, Sanskruti; Danisch, Meike Charlotte; Danu, Andrea; Das, Debasish; Das, Indranil; Das, Supriya; Dash, Ajay Kumar; Dash, Sadhana; Dashi, Anisa; De, Sudipan; De Caro, Annalisa; De Cataldo, Giacinto; De Conti, Camila; De Cuveland, Jan; De Falco, Alessandro; De Gruttola, Daniele; De Marco, Nora; De Pasquale, Salvatore; Derradi De Souza, Rafael; Franz Degenhardt, Hermann; Deisting, Alexander; Deloff, Andrzej; Delsanto, Silvia; Deplano, Caterina; Dhankher, Preeti; Di Bari, Domenico; Di Mauro, Antonio; Di Ruzza, Benedetto; Arteche Diaz, Raul; Dietel, Thomas; Dillenseger, Pascal; Ding, Yanchun; Divia, Roberto; Djuvsland, Oeystein; Dobrin, Alexandru Florin; Domenicis Gimenez, Diogenes; Donigus, Benjamin; Dordic, Olja; Van Doremalen, Lennart Vincent; Dubey, Anand Kumar; Dubla, Andrea; Ducroux, Laurent; Dudi, Sandeep; Duggal, Ashpreet Kaur; Dukhishyam, Mallick; Dupieux, Pascal; Ehlers Iii, Raymond James; Elia, Domenico; Endress, Eric; Engel, Heiko; Epple, Eliane; Erazmus, Barbara Ewa; Erhardt, Filip; Ersdal, Magnus Rentsch; Espagnon, Bruno; Eulisse, Giulio; Eum, Jongsik; Evans, David; Evdokimov, Sergey; Fabbietti, Laura; Faggin, Mattia; Faivre, Julien; Fantoni, Alessandra; Fasel, Markus; Feldkamp, Linus; Feliciello, Alessandro; Feofilov, Grigorii; Fernandez Tellez, Arturo; Ferretti, Alessandro; Festanti, Andrea; Feuillard, Victor Jose Gaston; Figiel, Jan; Araujo Silva Figueredo, Marcel; Filchagin, Sergey; Finogeev, Dmitry; Fionda, Fiorella; Fiorenza, Gabriele; Flor, Fernando; Floris, Michele; Foertsch, Siegfried Valentin; Foka, Panagiota; Fokin, Sergey; Fragiacomo, Enrico; Francescon, Andrea; Francisco, Audrey; Frankenfeld, Ulrich Michael; Fronze, Gabriele Gaetano; Fuchs, Ulrich; Furget, Christophe; Furs, Artur; Fusco Girard, Mario; Gaardhoeje, Jens Joergen; Gagliardi, Martino; Gago Medina, Alberto Martin; Gajdosova, Katarina; Gallio, Mauro; Duarte Galvan, Carlos; Ganoti, Paraskevi; Garabatos Cuadrado, Jose; Garcia-solis, Edmundo Javier; Garg, Kunal; Gargiulo, Corrado; Gasik, Piotr Jan; Gauger, Erin Frances; De Leone Gay, Maria Beatriz; Germain, Marie; Ghosh, Jhuma; Ghosh, Premomoy; Ghosh, Sanjay Kumar; Gianotti, Paola; Giubellino, Paolo; Giubilato, Piero; Glassel, Peter; Gomez Coral, Diego Mauricio; Gomez Ramirez, Andres; Gonzalez, Victor; Gonzalez Zamora, Pedro; Gorbunov, Sergey; Gorlich, Lidia Maria; Gotovac, Sven; Grabski, Varlen; Graczykowski, Lukasz Kamil; Graham, Katie Leanne; Greiner, Leo Clifford; Grelli, Alessandro; Grigoras, Costin; Grigoryev, Vladislav; Grigoryan, Ara; Grigoryan, Smbat; Gronefeld, Julius Maximilian; Grosa, Fabrizio; Grosse-oetringhaus, Jan Fiete; Grosso, Raffaele; Guernane, Rachid; Guerzoni, Barbara; Guittiere, Manuel; Gulbrandsen, Kristjan Herlache; Gunji, Taku; Gupta, Anik; Gupta, Ramni; Bautista Guzman, Irais; Haake, Rudiger; Habib, Michael Karim; Hadjidakis, Cynthia Marie; Hamagaki, Hideki; Hamar, Gergoe; Hamid, Mohammed; Hamon, Julien Charles; Hannigan, Ryan; Haque, Md Rihan; Harlenderova, Alena; Harris, John William; Harton, Austin Vincent; Hassan, Hadi; Hatzifotiadou, Despina; Hayashi, Shinichi; Heckel, Stefan Thomas; Hellbar, Ernst; Helstrup, Haavard; Herghelegiu, Andrei Ionut; Gonzalez Hernandez, Emma; Herrera Corral, Gerardo Antonio; Herrmann, Florian; Hetland, Kristin Fanebust; Hilden, Timo Eero; Hillemanns, Hartmut; Hills, Christopher; Hippolyte, Boris; Hohlweger, Bernhard; Horak, David; Hornung, Sebastian; Hosokawa, Ritsuya; Hota, Jyotishree; Hristov, Peter Zahariev; Huang, Chun-lu; Hughes, Charles; Huhn, Patrick; Humanic, Thomas; Hushnud, Hushnud; Hussain, Nur; Hussain, Tahir; Hutter, Dirk; Hwang, Dae Sung; Iddon, James Philip; Iga Buitron, Sergio Arturo; Ilkaev, Radiy; Inaba, Motoi; Ippolitov, Mikhail; Islam, Md Samsul; Ivanov, Marian; Ivanov, Vladimir; Izucheev, Vladimir; Jacak, Barbara; Jacazio, Nicolo; Jacobs, Peter Martin; Jadhav, Manoj Bhanudas; Jadlovska, Slavka; Jadlovsky, Jan; Jaelani, Syaefudin; Jahnke, Cristiane; Jakubowska, Monika Joanna; Janik, Malgorzata Anna; Jena, Chitrasen; Jercic, Marko; Jevons, Oliver; Jimenez Bustamante, Raul Tonatiuh; Jin, Muqing; Jones, Peter Graham; Jusko, Anton; Kalinak, Peter; Kalweit, Alexander Philipp; Kang, Ju Hwan; Kaplin, Vladimir; Kar, Somnath; Karasu Uysal, Ayben; Karavichev, Oleg; Karavicheva, Tatiana; Karczmarczyk, Przemyslaw; Karpechev, Evgeny; Kebschull, Udo Wolfgang; Keidel, Ralf; Keijdener, Darius Laurens; Keil, Markus; Ketzer, Bernhard Franz; Khabanova, Zhanna; Khan, Ahsan Mehmood; Khan, Shaista; Khan, Shuaib Ahmad; Khanzadeev, Alexei; Kharlov, Yury; Khatun, Anisa; Khuntia, Arvind; Kielbowicz, Miroslaw Marek; Kileng, Bjarte; Kim, Byungchul; Kim, Daehyeok; Kim, Dong Jo; Kim, Eun Joo; Kim, Hyeonjoong; Kim, Jinsook; Kim, Jiyoung; Kim, Minjung; Kim, Se Yong; Kim, Taejun; Kim, Taesoo; Kirsch, Stefan; Kisel, Ivan; Kiselev, Sergey; Kisiel, Adam Ryszard; Klay, Jennifer Lynn; Klein, Carsten; Klein, Jochen; Klein-boesing, Christian; Klewin, Sebastian; Kluge, Alexander; Knichel, Michael Linus; Knospe, Anders Garritt; Kobdaj, Chinorat; Varga-kofarago, Monika; Kohler, Markus Konrad; Kollegger, Thorsten; Kondratyeva, Natalia; Kondratyuk, Evgeny; Konevskikh, Artem; Konopka, Piotr Jan; Konyushikhin, Maxim; Kovalenko, Oleksandr; Kovalenko, Vladimir; Kowalski, Marek; Kralik, Ivan; Kravcakova, Adela; Kreis, Lukas; Krivda, Marian; Krizek, Filip; Kruger, Mario; Kryshen, Evgeny; Krzewicki, Mikolaj; Kubera, Andrew Michael; Kucera, Vit; Kuhn, Christian Claude; Kuijer, Paulus Gerardus; Kumar, Jitendra; Kumar, Lokesh; Kumar, Shyam; Kundu, Sourav; Kurashvili, Podist; Kurepin, Alexander; Kurepin, Alexey; Kuryakin, Alexey; Kushpil, Svetlana; Kvapil, Jakub; Kweon, Min Jung; Kwon, Youngil; La Pointe, Sarah Louise; La Rocca, Paola; Lai, Yue Shi; Lakomov, Igor; Langoy, Rune; Lapidus, Kirill; Lardeux, Antoine Xavier; Larionov, Pavel; Laudi, Elisa; Lavicka, Roman; Lea, Ramona; Leardini, Lucia; Lee, Seongjoo; Lehas, Fatiha; Lehner, Sebastian; Lehrbach, Johannes; Lemmon, Roy Crawford; Leon Monzon, Ildefonso; Levai, Peter; Li, Xiaomei; Li, Xing Long; Lien, Jorgen Andre; Lietava, Roman; Lim, Bong-hwi; Lindal, Svein; Lindenstruth, Volker; Lindsay, Scott William; Lippmann, Christian; Lisa, Michael Annan; Litichevskyi, Vladyslav; Liu, Alwina; Ljunggren, Hans Martin; Llope, William; Lodato, Davide Francesco; Loginov, Vitaly; Loizides, Constantinos; Loncar, Petra; Lopez, Xavier Bernard; Lopez Torres, Ernesto; Lowe, Andrew John; Luettig, Philipp Johannes; Luhder, Jens Robert; Lunardon, Marcello; Luparello, Grazia; Lupi, Matteo; Maevskaya, Alla; Mager, Magnus; Mahmood, Sohail Musa; Maire, Antonin; Majka, Richard Daniel; Malaev, Mikhail; Malik, Qasim Waheed; Malinina, Liudmila; Mal'kevich, Dmitry; Malzacher, Peter; Mamonov, Alexander; Manko, Vladislav; Manso, Franck; Manzari, Vito; Mao, Yaxian; Marchisone, Massimiliano; Mares, Jiri; Margagliotti, Giacomo Vito; Margotti, Anselmo; Margutti, Jacopo; Marin, Ana Maria; Markert, Christina; Marquard, Marco; Martin, Nicole Alice; Martinengo, Paolo; Martinez, Jacobb Lee; Martinez Hernandez, Mario Ivan; Martinez-garcia, Gines; Martinez Pedreira, Miguel; Masciocchi, Silvia; Masera, Massimo; Masoni, Alberto; Massacrier, Laure Marie; Masson, Erwann; Mastroserio, Annalisa; Mathis, Andreas Michael; Toledo Matuoka, Paula Fernanda; Matyja, Adam Tomasz; Mayer, Christoph; Mazzilli, Marianna; Mazzoni, Alessandra Maria; Meddi, Franco; Melikyan, Yuri; Menchaca-rocha, Arturo Alejandro; Meninno, Elisa; Mercado-perez, Jorge; Meres, Michal; Soncco Meza, Carlos; Mhlanga, Sibaliso; Miake, Yasuo; Micheletti, Luca; Mieskolainen, Matti Mikael; Mihaylov, Dimitar Lubomirov; Mikhaylov, Konstantin; Mischke, Andre; Mishra, Aditya Nath; Miskowiec, Dariusz Czeslaw; Mitra, Jubin; Mitu, Ciprian Mihai; Mohammadi, Naghmeh; Mohanty, Auro Prasad; Mohanty, Bedangadas; Khan, Mohammed Mohisin; Moreira De Godoy, Denise Aparecida; Perez Moreno, Luis Alberto; Moretto, Sandra; Morreale, Astrid; Morsch, Andreas; Mrnjavac, Teo; Muccifora, Valeria; Mudnic, Eugen; Muhlheim, Daniel Michael; Muhuri, Sanjib; Mukherjee, Maitreyee; Mulligan, James Declan; Gameiro Munhoz, Marcelo; Munning, Konstantin; Arratia Munoz, Miguel Ignacio; Munzer, Robert Helmut; Murakami, Hikari; Murray, Sean; Musa, Luciano; Musinsky, Jan; Myers, Corey James; Myrcha, Julian Wojciech; Naik, Bharati; Nair, Rahul; Nandi, Basanta Kumar; Nania, Rosario; Nappi, Eugenio; Narayan, Amrendra; Naru, Muhammad Umair; Nassirpour, Adrian Fereydon; Ferreira Natal Da Luz, Pedro Hugo; Nattrass, Christine; Rosado Navarro, Sebastian; Nayak, Kishora; Nayak, Ranjit; Nayak, Tapan Kumar; Nazarenko, Sergey; Negrao De Oliveira, Renato Aparecido; Nellen, Lukas; Nesbo, Simon Voigt; Neskovic, Gvozden; Ng, Fabian; Nicassio, Maria; Niedziela, Jeremi; Nielsen, Borge Svane; Nikolaev, Sergey; Nikulin, Sergey; Nikulin, Vladimir; Noferini, Francesco; Nomokonov, Petr; Nooren, Gerardus; Cabanillas Noris, Juan Carlos; Norman, Jaime; Nyanin, Alexander; Nystrand, Joakim Ingemar; Oh, Hoonjung; Ohlson, Alice Elisabeth; Oleniacz, Janusz; Oliveira Da Silva, Antonio Carlos; Oliver, Michael Henry; Onderwaater, Jacobus; Oppedisano, Chiara; Orava, Risto; Oravec, Matej; Ortiz Velasquez, Antonio; Oskarsson, Anders Nils Erik; Otwinowski, Jacek Tomasz; Oyama, Ken; Pachmayer, Yvonne Chiara; Pacik, Vojtech; Pagano, Davide; Paic, Guy; Palni, Prabhakar; Pan, Jinjin; Pandey, Ashutosh Kumar; Panebianco, Stefano; Papikyan, Vardanush; Pareek, Pooja; Park, Jonghan; Parkkila, Jasper Elias; Parmar, Sonia; Passfeld, Annika; Pathak, Surya Prakash; Patra, Rajendra Nath; Paul, Biswarup; Pei, Hua; Peitzmann, Thomas; Peng, Xinye; Pereira, Luis Gustavo; Pereira Da Costa, Hugo Denis Antonio; Peresunko, Dmitry Yurevich; Perez Lezama, Edgar; Peskov, Vladimir; Pestov, Yury; Petracek, Vojtech; Petrovici, Mihai; Petta, Catia; Peretti Pezzi, Rafael; Piano, Stefano; Pikna, Miroslav; Pillot, Philippe; Ozelin De Lima Pimentel, Lais; Pinazza, Ombretta; Pinsky, Lawrence; Pisano, Silvia; Piyarathna, Danthasinghe; Ploskon, Mateusz Andrzej; Planinic, Mirko; Pliquett, Fabian; Pluta, Jan Marian; Pochybova, Sona; Podesta Lerma, Pedro Luis Manuel; Poghosyan, Martin; Polishchuk, Boris; Poljak, Nikola; Poonsawat, Wanchaloem; Pop, Amalia; Poppenborg, Hendrik; Porteboeuf, Sarah Julie; Pozdniakov, Valeriy; Prasad, Sidharth Kumar; Preghenella, Roberto; Prino, Francesco; Pruneau, Claude Andre; Pshenichnov, Igor; Puccio, Maximiliano; Punin, Valery; Putschke, Jorn Henning; Raha, Sibaji; Rajput, Sonia; Rak, Jan; Rakotozafindrabe, Andry Malala; Ramello, Luciano; Rami, Fouad; Raniwala, Rashmi; Raniwala, Sudhir; Rasanen, Sami Sakari; Rascanu, Bogdan Theodor; Ratza, Viktor; Ravasenga, Ivan; Read, Kenneth Francis; Redlich, Krzysztof; Rehman, Attiq Ur; Reichelt, Patrick Simon; Reidt, Felix; Ren, Xiaowen; Renfordt, Rainer Arno Ernst; Reshetin, Andrey; Revol, Jean-pierre; Reygers, Klaus Johannes; Riabov, Viktor; Richert, Tuva Ora Herenui; Richter, Matthias Rudolph; Riedler, Petra; Riegler, Werner; Riggi, Francesco; Ristea, Catalin-lucian; Rode, Sudhir Pandurang; Rodriguez Cahuantzi, Mario; Roeed, Ketil; Rogalev, Roman; Rogochaya, Elena; Rohr, David Michael; Roehrich, Dieter; Rokita, Przemyslaw Stefan; Ronchetti, Federico; Dominguez Rosas, Edgar; Roslon, Krystian; Rosnet, Philippe; Rossi, Andrea; Rotondi, Alberto; Roukoutakis, Filimon; Roy, Christelle Sophie; Roy, Pradip Kumar; Vazquez Rueda, Omar; Rui, Rinaldo; Rumyantsev, Boris; Rustamov, Anar; Ryabinkin, Evgeny; Ryabov, Yury; Rybicki, Andrzej; Saarinen, Sampo; Sadhu, Samrangy; Sadovskiy, Sergey; Safarik, Karel; Saha, Sumit Kumar; Sahoo, Baidyanath; Sahoo, Pragati; Sahoo, Raghunath; Sahoo, Sarita; Sahu, Pradip Kumar; Saini, Jogender; Sakai, Shingo; Saleh, Mohammad Ahmad; Sambyal, Sanjeev Singh; Samsonov, Vladimir; Sandoval, Andres; Sarkar, Amal; Sarkar, Debojit; Sarkar, Nachiketa; Sarma, Pranjal; Sas, Mike Henry Petrus; Scapparone, Eugenio; Scarlassara, Fernando; Schaefer, Brennan; Scheid, Horst Sebastian; Schiaua, Claudiu Cornel; Schicker, Rainer Martin; Schmidt, Christian Joachim; Schmidt, Hans Rudolf; Schmidt, Marten Ole; Schmidt, Martin; Schmidt, Nicolas Vincent; Schukraft, Jurgen; Schutz, Yves Roland; Schwarz, Kilian Eberhard; Schweda, Kai Oliver; Scioli, Gilda; Scomparin, Enrico; Sefcik, Michal; Seger, Janet Elizabeth; Sekiguchi, Yuko; Sekihata, Daiki; Selyuzhenkov, Ilya; Senyukov, Serhiy; Serradilla Rodriguez, Eulogio; Sett, Priyanka; Sevcenco, Adrian; Shabanov, Arseniy; Shabetai, Alexandre; Shahoyan, Ruben; Shaikh, Wadut; Shangaraev, Artem; Sharma, Anjali; Sharma, Ankita; Sharma, Meenakshi; Sharma, Natasha; Sheikh, Ashik Ikbal; Shigaki, Kenta; Shimomura, Maya; Shirinkin, Sergey; Shou, Qiye; Shtejer Diaz, Katherin; Sibiryak, Yury; Siddhanta, Sabyasachi; Sielewicz, Krzysztof Marek; Siemiarczuk, Teodor; Silvermyr, David Olle Rickard; Simatovic, Goran; Simonetti, Giuseppe; Singaraju, Rama Narayana; Singh, Ranbir; Singh, Randhir; Singhal, Vikas; Sarkar - Sinha, Tinku; Sitar, Branislav; Sitta, Mario; Skaali, Bernhard; Slupecki, Maciej; Smirnov, Nikolai; Snellings, Raimond; Snellman, Tomas Wilhelm; Song, Jihye; Soramel, Francesca; Sorensen, Soren Pontoppidan; Sozzi, Federica; Sputowska, Iwona Anna; Stachel, Johanna; Stan, Ionel; Stankus, Paul; Stenlund, Evert Anders; Stocco, Diego; Storetvedt, Maksim Melnik; Strmen, Peter; Alarcon Do Passo Suaide, Alexandre; Sugitate, Toru; Suire, Christophe Pierre; Suleymanov, Mais Kazim Oglu; Suljic, Miljenko; Sultanov, Rishat; Sumbera, Michal; Sumowidagdo, Suharyo; Suzuki, Ken; Swain, Sagarika; Szabo, Alexander; Szarka, Imrich; Tabassam, Uzma; Takahashi, Jun; Tambave, Ganesh Jagannath; Tanaka, Naoto; Tarhini, Mohamad; Tariq, Mohammad; Tarzila, Madalina-gabriela; Tauro, Arturo; Tejeda Munoz, Guillermo; Telesca, Adriana; Terrevoli, Cristina; Teyssier, Boris; Thakur, Dhananjaya; Thakur, Sanchari; Thomas, Deepa; Thoresen, Freja; Tieulent, Raphael Noel; Tikhonov, Anatoly; Timmins, Anthony Robert; Toia, Alberica; Topilskaya, Nataliya; Toppi, Marco; Rojas Torres, Solangel; Tripathy, Sushanta; Trogolo, Stefano; Trombetta, Giuseppe; Tropp, Lukas; Trubnikov, Victor; Trzaska, Wladyslaw Henryk; Trzcinski, Tomasz Piotr; Trzeciak, Barbara Antonina; Tsuji, Tomoya; Tumkin, Alexandr; Turrisi, Rosario; Tveter, Trine Spedstad; Ullaland, Kjetil; Umaka, Ejiro Naomi; Uras, Antonio; Usai, Gianluca; Utrobicic, Antonija; Vala, Martin; Van Hoorne, Jacobus Willem; Van Leeuwen, Marco; Vande Vyvre, Pierre; Varga, Dezso; Diozcora Vargas Trevino, Aurora; Vargyas, Marton; Varma, Raghava; Vasileiou, Maria; Vasiliev, Andrey; Vauthier, Astrid; Vazquez Doce, Oton; Vechernin, Vladimir; Veen, Annelies Marianne; Vercellin, Ermanno; Vergara Limon, Sergio; Vermunt, Luuk; Vernet, Renaud; Vertesi, Robert; Vickovic, Linda; Viinikainen, Jussi Samuli; Vilakazi, Zabulon; Villalobos Baillie, Orlando; Villatoro Tello, Abraham; Vinogradov, Alexander; Virgili, Tiziano; Vislavicius, Vytautas; Vodopyanov, Alexander; Volkl, Martin Andreas; Voloshin, Kirill; Voloshin, Sergey; Volpe, Giacomo; Von Haller, Barthelemy; Vorobyev, Ivan; Voscek, Dominik; Vranic, Danilo; Vrlakova, Janka; Wagner, Boris; Wang, Hongkai; Wang, Mengliang; Watanabe, Yosuke; Weber, Michael; Weber, Steffen Georg; Wegrzynek, Adam; Weiser, Dennis Franz; Wenzel, Sandro Christian; Wessels, Johannes Peter; Westerhoff, Uwe; Whitehead, Andile Mothegi; Wiechula, Jens; Wikne, Jon; Wilk, Grzegorz Andrzej; Wilkinson, Jeremy John; Willems, Guido Alexander; Williams, Crispin; Willsher, Emily; Windelband, Bernd Stefan; Witt, William Edward; Xu, Ran; Yalcin, Serpil; Yamakawa, Kosei; Yano, Satoshi; Yin, Zhongbao; Yokoyama, Hiroki; Yoo, In-kwon; Yoon, Jin Hee; Yurchenko, Volodymyr; Zaccolo, Valentina; Zaman, Ali; Zampolli, Chiara; Correa Zanoli, Henrique Jose; Zardoshti, Nima; Zarochentsev, Andrey; Zavada, Petr; Zavyalov, Nikolay; Zbroszczyk, Hanna Paulina; Zhalov, Mikhail; Zhang, Xiaoming; Zhang, Yonghong; Zhang, Zuman; Zhao, Chengxin; Zherebchevskii, Vladimir; Zhigareva, Natalia; Zhou, Daicui; Zhou, You; Zhou, Zhuo; Zhu, Hongsheng; Zhu, Jianhui; Zhu, Ya; Zichichi, Antonino; Zimmermann, Markus Bernhard; Zinovjev, Gennady; Zmeskal, Johann; Zou, Shuguang

2018-01-01

The measurement of electron-positron pair production is presented as a function of their invariant mass and transverse momentum at midrapidity ($|y_{\\rm e} | < 0.8$) in proton-proton (pp) collisions at a centre-of-mass energy of $\\sqrt{s} = 13$ TeV. The contributions from light-hadron decays can be calculated from their measured cross sections in pp collisions at $\\sqrt{s} = 7$ TeV or $13$ TeV. The remaining continuum originates from correlated semileptonic decays of heavy-flavour hadrons. Fitting the data with templates from two different Monte Carlo event generators, PYTHIA and POWHEG , the charm and beauty cross sections at midrapidity are extracted for the first time at this collision energy: ${\\rm d}\\sigma_{\\rm{c\\overline c}} /{\\rm d}y|{_ {y=0}} = 974 \\pm 138 {\\rm (stat.)} \\pm 140 {\\rm (syst.)}$ $\\mu$b and ${\\rm d}\\sigma_{\\rm{b\\overline b}} /{\\rm d}y|{_ {y=0}} = 79 \\pm 14 {\\rm (stat.)} \\pm 11 {\\rm (syst.)}$ $\\mu$b using PYTHIA simulations and ${\\rm d}\\sigma_{\\rm{c\\overline c}} /{\\rm d}y|{_ {y=0}} = 14...

Isotopic composition of groundwater in semi-arid regions of Southern Africa

International Nuclear Information System (INIS)

Vogel, J.C.; Urk, H. van

1975-01-01

Although the isotope content of precipitation in the semi-arid regions of southern Africa is extremely variable, groundwater samples from the same district are found to have a remarkably constant isotopic composition. The oxygen-18 content of the underground water, in general, varies by about 0.5% in a given area. The differences that occur between different regions are sufficiently large to allow the groundwater of an area to be characterized by means of its oxygen-18 content. In order to localize the infiltration area of an aquifer, radiocarbon dating of the water is used. It appears that the groundwater contains, in general, less of the heavy isotopes than does the precipitation in the recharge area. This indicates that infiltration only takes place during periods of heavy rainfall. Examples are given where the isotope content of the groundwater is used to distinguish between different aquifers in the same region

Gamma ray induced sensitization in CaSO4:Dy and competing trap model

International Nuclear Information System (INIS)

Nagpal, J.S.; Kher, R.K.; Gangadharan, P.

1979-01-01

Gamma ray induced sensitization in CaSO 4 :Dy has been compared (by measurement of TL glow curves) for different temperatures during irradiation (25 0 , 120 0 and 250 0 C). Enhanced sensitization at elevated temperatures seems to support the competing trap model for supralinearity and sensitization in CaSO 4 :Dy. (author)

Studies on the decay of 160Tb to levels in 160Dy by Ge (Li)-Ge(Li)-coincidence system

International Nuclear Information System (INIS)

Hassan, A.M.; Abou-Zeid, M.A.; Mekamer, M.

1981-01-01

This work concerned with the study of the energy levels and the properties of gamma-ray transitions in 160 Dy resulting from the B-decay of the parent radioactive isotope 160 Tb (72 d.). These studies have been done by means of, single and gamma-gamma coincidence measurements. Log(ft). Internal Conversion Coefficient (ICC) values and the branching ratios have been calculated. The construction and testes of the Ge(Li)-Ge(Li) gamma-gamma coincidence spectrometer are presented. In addition to the previously reported transitions in three new transitions of energies 203, 420 and 1048 keV have been observed for the first time. The energy level at 1288.60 keV is confirmed, due to the presence of the 246 keV and 1005 keV gamma-ray transitions in the singles and gamma-gamma coincidence spectra. Furthermore the B-intensity feeding this level was calculated for the first time to be 0.08%. The log(ft) values of the energy level at 1288.6 keV was calculated for the first time to be 10.79. The energy level diagram of 160 Dy as summerised in the present work consists of 12 excited states, the levels at 581(6 + ) and 1391 keV reported by some authors were not encluded, since no transitions populated or depopulated these levels could be observed

Isotopically labelled vitamin D derivatives and processes for preparing same

International Nuclear Information System (INIS)

Deluca, H.R.; Schnoes, H.K.; Napoli, J.L.; Fivizzani, M.A.

1981-01-01

This invention relates to 26,27-isotopically labelled vitamin D 3 compounds, including radiolabelled vitamin D 3 compounds of high specific activity, methods for their preparation, and intermediates obtained in their synthesis. The method involves reacting an ester of a 26,27-dinor-vitamin D-25-carboxylic acid with an isotopically labelled methyl Grignard reagent or methyl lithium reagent to obtain a 26,27-isotopically labelled compound in which at least some of the H atoms and/or C atoms are heavy isotopes. (author)

Chromatographic hydrogen isotope separation

International Nuclear Information System (INIS)

Aldridge, F.T.

1983-01-01

Intermetallic compounds with the CaCu5 type of crystal structure, particularly LaNiCo and CaNi5, exhibit high separation factors and fast equilibrium times and therefore are useful for packing a chromatographic hydrogen isotope separation column. The addition of an inert metal to dilute the hydride improves performance of the column. A large scale multi-stage chromatographic separation process run as a secondary process off a hydrogen feedstream from an industrial plant which uses large volumes of hydrogen can produce large quantities of heavy water at an effective cost for use in heavy water reactors

Chromatographic hydrogen isotope separation

International Nuclear Information System (INIS)

Aldridge, F.T.

1981-01-01

Intermetallic compounds with the CaCu5 type of crystal structure , particularly LaNiCo and CaNi5, exhibit high separation factors and fast equilibrium times and therefore are useful for packing a chromatographic hydrogen isotope separation colum. The addition of an inert metal to dilute the hydride improves performance of the column. A large scale mutli-stage chromatographic separation process run as a secondary process off a hydrogen feedstream from an industrial plant which uses large volumes of hydrogen can produce large quantities of heavy water at an effective cost for use in heavy water reactors

Experimental study and thermodynamic assessment of the ZrO2-DyO1.5 system

International Nuclear Information System (INIS)

Wang, Chong; Zinkevich, M.; Aldinger, F.; Stuttgart Univ.

2007-01-01

The phase equilibria and thermodynamic properties in the ZrO 2 -DyO 1.5 system have been studied using the experimental methods of X-ray diffraction, scanning electron microscopy, energy dispersive X-ray spectroscopy, differential thermal analysis and high temperature drop calorimetry. The tetragonal + fluorite and fluorite + C-Dy 2 O 3 phase equilibria between 1400 C and 1700 C have been determined, together with the enthalpy increments of the materials with 30 mol.% and 50 mol.% DyO 1.5 in the temperature range 200-1400 C. Furthermore, the martensitic transformation temperatures (A s ,M s ) have been measured for the samples with 1 and 2 mol.% DyO 1.5 . Finally, thermodynamic assessment has been carried out using the experimental results obtained and literature data. (orig.)

Phase composition of iron-rich R-Fe-Si (R=Dy, Ho, Er) alloys

International Nuclear Information System (INIS)

Ivanova, G.V.; Makarova, G.M.; Shcherbakova, E.V.; Belozerov, E.V.

2005-01-01

Phase composition is studied in iron-rich alloys of R-Fe-Si (R=Dy, Ho, Er). In the as-cast state R 2 (Fe, Si) 17 of type Th 2 Ni 17 and R(Fe, Si) 12 compounds are observed; in the alloys of rated composition of R(Fe 0.85 Si 0.15 ) 8.5 (R=Dy, Er) a compound R 2 (Fe, Si) 17 of Th 2 Zn 17 -type is revealed as well. The annealing at 1273 K results in formation of Dy 3 (Fe, Si) 29 and also the compounds with the presumed composition of Dy 4 (Fe, Si) 41 and Ho 4 (Fe, Si) 41 . As this takes place the alloys contain a transition structure as well that represents a set of small-sized areas with various type short-range order in mutual displacement of Fe-Fe(Si) dumpbell chains. The process of phase formation at 1273 K is faced with difficulties. Even the annealing for 1000 h does not result in the state of equilibrium [ru

Synthesis and characterization of CaF{sub 2}:Dy nanophosphor for dosimetric application

Energy Technology Data Exchange (ETDEWEB)

Bhadane, Mahesh S.; Dahiwale, S. S.; Bhoraskar, V. N.; Dhole, S. D., E-mail: sanjay@physics.unipune.ac.in [Department of Physics, University of Pune, Pune-411007 (India); Patil, B. J. [Department of Physics, Abasaheb Garware College, Pune-411004 (India); Kulkarni, M. S. [Radiation Safety Systems Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India); Bhatt, B. C. [Radiological Physics and Advisory Division, Bhabha Atomic Research Centre, Mumbai 400 085 (India)

2015-06-24

In this work, nanoparticles (NPs) of dysprosium doped calcium fluoride (CaF{sub 2}:Dy) 1 mol % has been prepared using simple chemical co-precipitation method and its thermoluminescence (TL) dosimetric properties were studied. The synthesized nanoparticle sample was characterized by X-ray diffraction (XRD) and the particle size of face centered cubic phase NPs was found around 30 nm. The shape, morphology and size were also observed by scanning electron microscopy (SEM). From gamma irradiated CaF{sub 2}:Dy TL curves, it was observed that the total areas of all the glow peak intensities are dramatically changed with increase in annealing temperature. Further, TL glow curve of the CaF{sub 2}:Dy at 183 °C annealed at 400 °C, showed very sharp linear response in the dose range from 1 Gy to 750 Gy. This linear response of CaF{sub 2}:Dy nanophosphor as a function of gamma dose is very useful from radiation dosimetric point of view.

Grain boundary engineering in sintered Nd-Fe-B permanent magnets for efficient utilization of heavy rare earth elements

Energy Technology Data Exchange (ETDEWEB)

Loewe, Konrad

2016-10-18

The first part of the thesis investigates the diffusion of rare-earth (RE) elements in commercial sintered Nd-Fe-B based permanent magnets. A strong temperature dependence of the diffusion distance and resulting change in magnetic properties were found. A maximum increase in coercivity of ∼+350 kA/m using a Dy diffusion source occurred at the optimum annealing temperature of 900 C. After annealing for 6 h at this temperature, a Dy diffusion distance of about 4 mm has been observed with a scanning Hall probe. Consequently, the maximum thickness of grain boundary diffusion processed magnets with homogeneous properties is also only a few mm. The microstructural changes in the magnets after diffusion were investigated by electron microscopy coupled with electron probe microanalysis. It was found that the diffusion of Dy into sintered Nd-Fe-B permanent magnets occurs along the grain boundary phases, which is in accordance with previous studies. A partial melting of the Nd-Fe-B grains during the annealing process lead to the formation of so - called (Nd,Dy)-Fe-B shells at the outer part of the grains. These shells are μm thick at the immediate surface of the magnet and become thinner with increasing diffusion distance towards the center of the bulk. With scanning transmission electron microscopy coupled with electron probe analysis a Dy content of about 1 at.% was found in a shell located about 1.5 mm away from the surface of the magnet. The evaluation of diffusion speeds of Dy and other RE (Tb, Ce, Gd) in Nd-Fe-B magnets showed that Tb diffuses significantly faster than Dy, and Ce slightly slower than Dy, which is attributed to differences in the respective phase diagrams. The addition of Gd to the grain boundaries has an adverse effect on coercivity. Exemplary of the heavy rare earth element Tb, the nano - scale elemental distribution around the grain boundaries after the diffusion process was visualized with high resolution scanning transmission electron microscopy

Isotopic studies of Yucca Mountain soil fluids and carbonate pedogenesis

International Nuclear Information System (INIS)

McConnaughey, T.A.; Whelan, J.F.; Wickland, K.P.; Moscati, R.J.

1994-01-01

Secondary carbonates occurring within the soils, faults, and subsurface fractures of Yucca Mountain contain some of the best available records of paleoclimate and palehydrology for the potential radioactive waste repository site. This article discusses conceptual and analytical advances being made with regard to the interpretation of stable isotope data from pedogenic carbonates, specifically related to the 13 C content of soil CO 2 , CaCO 3 , precipitation mechanisms, and isotopic fractionations between parent fluids and precipitating carbonates. The 13 C content of soil carbon dioxide from Yucca Mountain and vicinity shows most of the usual patterns expected in such contexts: Decreasing 13 C content with depth decreasing 13 C with altitude and reduced 13 C during spring. These patterns exist within the domain of a noisy data set; soil and vegetational heterogeneities, weather, and other factors apparently contribute to isotopic variability in the system. Several soil calcification mechanisms appear to be important, involving characteristic physical and chemical environments and isotopic fractionations. When CO 2 loss from thin soil solutions is an important driving factor, carbonates may contain excess heavy isotopes, compared to equilibrium precipitation with soil fluids. When root calcification serves as a proton generator for plant absorption of soil nutrients, heavy isotope deficiencies are likely. Successive cycles of dissolution and reprecipitation mix and redistribute pedogenic carbonates, and tend to isotopically homogenize and equilibrate pedogenic carbonates with soil fluids

Applications of heavy-ion reactions on hydrogen isotopes

International Nuclear Information System (INIS)

Evers, E.J.

1987-01-01

This thesis describes various aspects of 'inverse' reactions between the lightest nuclides, hydrogen and deuterium, and heavy ions in the range from carbon to phosphorus. The reactions studied in this thesis always result in one light ejectile and one excited heavy nucleus. Coincidence experiments have been performed in which both the emitted light particle and the gamma radiation emitted by the excited heavy nucleus produced, are detected. Ch. 1 describes the system built for the acquisition of data obtained in such coincidence experiments. Ch. 2 describes precision measurements of nuclear lifetimes and stopping powers. Coincident Doppler shift attenuation (DSA) experiments were performed with the reaction 2 H( 31 P,pγ) 32 P at E( 31 P 7+ )=50 MeV and thin Ti 2 H targets on Au, Ag and Cu backings. Mean lifetimes of the E x =513, 1150, 1323 and 1755 levels were determined with experimental stopping powers of Forster et al. These lifetimes were used as input in further analysis of the experimental data and of an additional experiment with a target on Mg backing to determine a consistent set of stopping power data for P ions with a velocity in the range 0-8(c/137) in the four materials mentioned. Ch.'s 3 and 4 deal with narrow resonances in reactions of nitrogen and fluorine beams with hydrogen targets. In Ch. 3 a method is described for the calibration of analyzing-magnet systems of heavy-ions accelerators. Ch. 4 describes an experiment to investigate the hydrogen concentration in silicon nitride films using a resonant inverse nuclear reaction. This method turns out to be a very suitable one for determining hydrogen concentration profiles with a good depth resolution over a large depth. 69 refs.; 23 figs.; 7 tabs

Single-molecule magnet behavior in an octanuclear dysprosium(iii) aggregate inherited from helical triangular Dy3 SMM-building blocks.

Science.gov (United States)

Zhang, Li; Zhang, Peng; Zhao, Lang; Wu, Jianfeng; Guo, Mei; Tang, Jinkui

2016-06-28

An unprecedented octanuclear dysprosium(iii) cluster with the formula [Dy8L6(μ3-OH)4(μ2-CH3O)2(CH3OH)6(H2O)2]·6H2O·10CH3OH·2CH3CN () based on a nonlinearly tritopic aroylhydrazone ligand H3L has been isolated, realizing the successful linking of pairwise interesting triangular Dy3 SMMs. It is noteworthy that two enantiomers (Λ and Δ configurations) individually behaving as a coordination-induced chirality presented in the Dy3 helicate are connected in the meso Dy8 cluster. Remarkably, alternating-current magnetic susceptibility measurements revealed that the Dy8 cluster shows typical SMM behavior inherited from its Dy3 helical precursor. It is one of the rare polynuclear Lnn SMMs (n > 7) under zero dc field.

Effect of co-doping Tm3+ ions on the emission properties of Dy3+ ions in tellurite glasses

International Nuclear Information System (INIS)

Sasikala, T.; Rama Moorthy, L.; Mohan Babu, A.; Srinivasa Rao, T.

2013-01-01

The present work reports the absorption, photoluminescence and decay properties of singly doped Dy 3+ and co-doped Dy 3+ /Tm 3+ ions in TeO 2 +ZnO+K 2 O+CaO (TZKC) glasses prepared by the melt quenching technique. The glassy nature of the host glass has been confirmed by X-ray diffraction analysis and the primary vibrational modes were determined from the Raman spectrum. Judd–Ofelt (JO) analysis has been used to calculate the radiative transition rates, branching ratios and radiative lifetime of the emitting 4 F 9/2 state. The effect of co-doping of different concentrations of Tm 3+ ions on the emission properties of Dy 3+ ions has been investigated. The decay profiles of the 4 F 9/2 level were fitted to double exponential as well as Inokuti–Hirayama (IH) model to determine the energy transfer rates between Dy 3+ and Tm 3+ ions. The energy transfer rates found to increase with the increase of Tm 3+ ions concentration. The chromaticity coordinates and color purity of the emitted light for all glasses were determined. - Graphical abstract: The graphical abstract shows the emission spectra of Dy 3+ , Tm 3+ and Dy 3+ /Tm 3+ co-doped TZKC glasses recorded by exciting at 355 nm wavelength. - Highlights: • Zinc tellurite glasses doped with Dy 3+ , Tm 3+ and Dy 3+ /Tm 3+ ions were prepared. • XRD, DTA and Raman spectral measurements were recorded to know the nature of host. • Energy transfer occurs from Dy 3+ ions to Tm 3+ ions. • The color purity of the emitted light was determined

Diffusion processes in dyed detectors

International Nuclear Information System (INIS)

Lferde, M.; Seidel, J.-L.; Monnin, M.

1982-01-01

In order to get a better understanding of the dyed and fluorescent track detectors, the diffusion speed of the swelling agent, the sensitization molecules and the dye have been measured under various conditions. It is shown that the sensitization affects the entire detector while dyeing is restricted to the upper and lower layers of the detector. By combining the optimal values of the reactions parameters a higher contrast and sensitivity may be achieved. (author)

[Effect of charge compensation on emission spectrum of Sr2SiO4 : Dy3+ phosphor].

Science.gov (United States)

Li, Pan-Lai; Wang, Zhi-Jun; Yang, Zhi-Ping; Guo, Qing-Lin

2009-01-01

The Sr2SiO4 : Dy3+ phosphor was synthesized by the high temperature solid-state reaction method in air. Dy2O3 (99.9%), SiO2 (99.9%), SrCO3 (99.9%), Li2CO3 (99.9%), Na2CO3 (99.9%) and K2CO3 (99.9%) were used as starting materials, and the Dy3+ doping concentration was 2 mol%. The emission spectrum was measured by a SPEX1404 spectrophotometer, and all the characterization of the phosphors was conducted at room temperature. The emission spectrum of Sr2 SiO4 : Dy3+ phosphor showed several bands centered at 486, 575 and 665 nm under the 365 nm excitation. The effect of Li+, Na+ and K+ on the emission spectra of Sr2SiO4 : Dy3+ phosphor was studied. The results show that the location of the emission spectrum of Sr2SiO4 : Dy3+ phosphor was not influenced by Li+, Na+ and K+. However, the emission spectrum intensity was greatly influenced by Li+, Na+ and K+, and the evolvement trend was monotone with different charge compensation, i. e. the emission spectrum intensity of Sr2SiO4 : Dy3+ phosphor firstly increased with increasing Li+ concentration, then decreased. However the charge compensation concentration corresponding to the maximum emission intensity was different with different charge compensation, and the concentration is 4, 3 and 3 mol% corresponding to Li+, Na+ and K+, respectively. And the theoretical reason for the above results was analyzed.

Spin canting in a Dy-based single-chain magnet with dominant next-nearest-neighbor antiferromagnetic interactions

Science.gov (United States)

Bernot, K.; Luzon, J.; Caneschi, A.; Gatteschi, D.; Sessoli, R.; Bogani, L.; Vindigni, A.; Rettori, A.; Pini, M. G.

2009-04-01

We investigate theoretically and experimentally the static magnetic properties of single crystals of the molecular-based single-chain magnet of formula [Dy(hfac)3NIT(C6H4OPh)]∞ comprising alternating Dy3+ and organic radicals. The magnetic molar susceptibility χM displays a strong angular variation for sample rotations around two directions perpendicular to the chain axis. A peculiar inversion between maxima and minima in the angular dependence of χM occurs on increasing temperature. Using information regarding the monomeric building block as well as an ab initio estimation of the magnetic anisotropy of the Dy3+ ion, this “anisotropy-inversion” phenomenon can be assigned to weak one-dimensional ferromagnetism along the chain axis. This indicates that antiferromagnetic next-nearest-neighbor interactions between Dy3+ ions dominate, despite the large Dy-Dy separation, over the nearest-neighbor interactions between the radicals and the Dy3+ ions. Measurements of the field dependence of the magnetization, both along and perpendicularly to the chain, and of the angular dependence of χM in a strong magnetic field confirm such an interpretation. Transfer-matrix simulations of the experimental measurements are performed using a classical one-dimensional spin model with antiferromagnetic Heisenberg exchange interaction and noncollinear uniaxial single-ion anisotropies favoring a canted antiferromagnetic spin arrangement, with a net magnetic moment along the chain axis. The fine agreement obtained with experimental data provides estimates of the Hamiltonian parameters, essential for further study of the dynamics of rare-earth-based molecular chains.

Studies on up-gradation of Erbium from a heavy fraction of rare earths with EHEHPA

International Nuclear Information System (INIS)

Singh, D.K.; Anitha, M.; Yadav, K.K.; Kotekar, M.K.; Vijayalakshmi, R.; Singh, H.

2014-01-01

Erbium is an important heavy rare earth element, which finds wide applications. Recently, use of Erbium oxide as structural coating material in fusion reactor has stimulated the interest in obtaining Erbium in pure form. The separation of Erbium from other rare earths such as Dy, Ho, Y, Yb, Tm etc is very difficult due to low separation factor owing to their similar chemical properties. Additionally due to very low concentration ( 2 O 3 : 1.09, Dy 2 O 3 : 58.07, Er 2 O 3 : 22.0, Ho 2 O 3 : 13.33, Yb 2 O 3 : 4.74, Tm 2 O 3 :0.67 is obtained during purification of Y by Aliquat 336 from thiocyanate medium. In the present investigation this HRE fraction is taken as the feed material for up-gradation of Er by an acidic extractant namely 2 ethyl hexyl - 2 ethyl hexyl phosphonic acid (EHEHPA)

Isotopic-tracer-aided studies on undesirable effects of heavy metals in the soil-plant system. Part of a coordinated programme on isotopic-tracer-aided studies of agrochemical residue - soil biota interactions

International Nuclear Information System (INIS)

Oberlaender, H.E.

1982-07-01

Uptake of isotopically labelled mercury (Hg-203), cadmium (Cd-115m) and zinc (Zn-65) from a calcareous chernozem and a podzolized brown earth by spring and winter varieties of wheat, rye and barley was investigated in pot experiments carried out until maturity of the plants. The labelled heavy metals, applied at concentrations innocuous to plant growth (0.5 ppm Hg or Cd, 50 ppm Zn) were determined radiometrically in the straw and in the grains of the harvested plants, as well as in the milling products (bran, semolina and flour) obtained by standard procedures of grain processing. Uptake of mercury was several hundred times smaller than the uptake of cadmium, if both metals were applied to the soil in equal amounts. Whereas the uptake of mercury from the acid soil was insignificant or not detectable, cadmium was taken up from this soil at a much higher rate than from the alkaline soil. Thus, not mercury, but cadmium imposes the greatest hazard on the food chain. Winter varieties of cereals took up more mercury and cadmium than did spring varieties. The content of heavy metals in the plants decreased considerably when plants approached maturity. During translocation through the plants the metals were gradually retained when passing from the stalks (''straw'') into the grains, and from the seed-cover (''bran'') into the endosperm (''flour''). The heavy metal contents of the grain fractions decreased in the order: bran > semolina > flour. Concentrations of heavy metals in flour were 3-8 times smaller than in straw, showing that flour is least affected by heavy metal pollution of cereals via the soil. The metal content of the various flour types was correlated with their percentage of bran and with their ash content. By adding an ion-exchanger to the soil the pattern of relative distribution of heavy metals in mature plants was not changed, but the cadmium content of all cereal products was considerably lowered

Development of the dyed-track method for Kodak CN-85 detector

International Nuclear Information System (INIS)

Somogyi, G.; Toth-Szilagyi, M.; Varga, Z.; Monnin, M.; Lferde, M.

1984-01-01

The dyed-track method has been successfully developed for cellulose derivatives. The track parameters (width, colouration deepness, contrast, registration sensitivity), however, proved to be very dependent on the detector material and on the track processing conditions. In our previous works optimum conditions were presented mostly for cellulose acetate sheets. In the present work we have studied the influence of track processing parameters on the dyed-track formation in Kodak cellulose nitrate detector called CN-85. It is found that in this material optimum dyed-tracks can be produced with using no swelling but with a thermal annealing at 100 deg C for 1 hour after particle irradiation. For sensitization a treatment with 15% HCl at 22 deg C for 20 hours and for dyeing 0.3 wt% Rhodamine-B at 100 deg C for 1 hour proved to be the best. For better understanding the track dyeing phenomenon we have studied the colouration behaviour of electron-irradiated CN-85 detectors. (author)

Development of the dyed-track method for Kodak CN-85 detector

Energy Technology Data Exchange (ETDEWEB)

Somogyi, G.; Toth-Szilagyi, M.; Varga, Z. (Magyar Tudomanyos Akademia, Debrecen. Atommag Kutato Intezete); Monnin, M.; Lferde, M. (Clermont-Ferrand-2 Univ., 63 - Aubiere (France). Lab. de Physique Corpusculaire)

1984-01-01

The dyed-track method has been successfully developed for cellulose derivatives. The track parameters (width, colouration deepness, contrast, registration sensitivity), however, proved to be very dependent on the detector material and on the track processing conditions. In our previous works optimum conditions were presented mostly for cellulose acetate sheets. In the present work we have studied the influence of track processing parameters on the dyed-track formation in Kodak cellulose nitrate detector called CN-85. It is found that in this material optimum dyed-tracks can be produced with using no swelling but with a thermal annealing at 100 deg C for 1 hour after particle irradiation. For sensitization a treatment with 15% HCl at 22 deg C for 20 hours and for dyeing 0.3 wt% Rhodamine-B at 100 deg C for 1 hour proved to be the best. For better understanding the track dyeing phenomenon we have studied the colouration behaviour of electron-irradiated CN-85 detectors.

Omigapil treatment decreases fibrosis and improves respiratory rate in dy(2J mouse model of congenital muscular dystrophy.

Directory of Open Access Journals (Sweden)

Qing Yu

Full Text Available Congenital muscular dystrophy is a distinct group of diseases presenting with weakness in infancy or childhood and no current therapy. One form, MDC1A, is the result of laminin alpha-2 deficiency and results in significant weakness, respiratory insufficiency and early death. Modification of apoptosis is one potential pathway for therapy in these patients.dy(2J mice were treated with vehicle, 0.1 mg/kg or 1 mg/kg of omigapil daily via oral gavage over 17.5 weeks. Untreated age matched BL6 mice were used as controls. Functional, behavioral and histological measurements were collected.dy(2J mice treated with omigapil showed improved respiratory rates compared to vehicle treated dy(2J mice (396 to 402 vs. 371 breaths per minute, p<0.03 and similar to control mice. There were no statistical differences in normalized forelimb grip strength between dy(2J and controls at baseline or after 17.5 weeks and no significant differences seen among the dy(2J treatment groups. At 30-33 weeks of age, dy(2J mice treated with 0.1 mg/kg omigapil showed significantly more movement time and less rest time compared to vehicle treated. dy(2J mice showed normal cardiac systolic function throughout the trial. dy(2J mice had significantly lower hindlimb maximal (p<0.001 and specific force (p<0.002 compared to the control group at the end of the trial. There were no statistically significant differences in maximal or specific force among treatments. dy(2J mice treated with 0.1 mg/kg/day omigapil showed decreased percent fibrosis in both gastrocnemius (p<0.03 and diaphragm (p<0.001 compared to vehicle, and in diaphragm (p<0.013 when compared to 1 mg/kg/day omigapil treated mice. Omigapil treated dy(2J mice demonstrated decreased apoptosis.Omigapil therapy (0.1 mg/kg improved respiratory rate and decreased skeletal and respiratory muscle fibrosis in dy(2J mice. These results support a putative role for the use of omigapil in laminin deficient congenital muscular dystrophy

Preparation of 166 Dy/166 Ho-Macro aggregates as an In vivo generator system for the treatment of arthrophaties

International Nuclear Information System (INIS)

Aldama A, T.K.

2003-01-01

The present work reports the obtention of macro aggregates of hydroxides of Dysprosium-166/Holmium-166 ( 166 Dy/ 166 Ho-MH), as a generator system in vivo to be used in the treatment of arthritis rheumatoid. The 166 Dy was obtained by neutron irradiation of 166 DyO 3 (enriched to 98.45%) by 20 h in the TRIGA Mark III Reactor and 50 h of decay, to the oxide of 166 Dy/ 166 Ho formed, it was added HCl 0.12 N to obtain a final volume of 3.5 ml of solution of 166 Dy/ 166 Ho chloride. The solution of 166D yCl 3 solution was obtained with an activity of 3.502 mCi (129 MBq), appropriate for the preparation of the radiopharmaceutical 166 Dy/ 166 Ho-MH. The separation of the 166 Dy from the 166 Ho, was carried out by chromatography in an cation exchange column, gaining an appropriate separation, obtaining a 166 Dy with a radionuclide purity greater than 90%. The 166 Dy/ 166 Ho-MH were prepared by addition to the solution of 166 DyCI 3 NaOH 0.5 N low ultrasonic bath with later centrifugation, decanted and resuspension in saline solution, obtaining a radiopharmaceutical with a generator system 166 Dy/ 166 Ho with particles of size average of 3 μm, in form of 166 Dy / 166 Ho-MH. Under these conditions, it was obtained a radiochemical yield greater than 99%. The microscopic analysis and of filtration showed that the formulation doesn't present particles smaller than to 1 μm, neither greater to 50 μm, which will allow, the quick phagocytosis for the synoviocytes of the synovial membrane, and by consequence, an homogeneous distribution of the radiation dose could exist. The sedimentation velocity for the formulated suspension is of 0.04 cm/min that it will allow the administration of homogeneous activities of the radiopharmaceutical, to the no deposit in the injection devices. The studies of stability in vitro indicate us that inside the articulation, the particles won't probably reduce its size neither their radiochemical purity, for that the flight extra articular will be

Structure and magnetic properties of hot deformed Nd2Fe14B magnets doped with DyHx nanoparticles

Science.gov (United States)

Wang, C. G.; Yue, M.; Zhang, D. T.; Liu, W. Q.; Zhang, J. X.

2016-04-01

Commercial NdFeB powders mixed with DyHx nanoparticles are hot pressed and hot deformed into anisotropic magnets by Spark Plasma Sintering (SPS). The hot deformed magnet exhibits strong c-axis crystallographic texture. The coercivity of the magnet doped with 1.0 wt% DyHx is increased by 66.7%, compared with the magnet without DyHx, while the remanence decreases only by 3%. TEM observation shows that there exists a continuous (Nd,Dy)2Fe14B layer between Nd-rich phase and NdFeB main phase.

Possible interplay between non-axial and hexadecapole degrees of freedom. An explanation for ''enormously'' large Q4

International Nuclear Information System (INIS)

Dudek, J.; Nazarewicz, W.; Rozmej, P.

1980-02-01

The theoretical calculations of equilibrium deformations and multipole moments of rare earth nuclei are presented. The good agreement with experiment for Gd, Dy, Er, Yb nuclei is found in contrast to large discrepancies for heavy Hf, W and Os isotopes, especially connected with hexadecapole deformations and moments. Possibilities of the explanation of the above hexadecapole anomaly are discussed. The assumption of the ''partial-bubble''-like density distribution, suggested from electron scattering measurements, is found to be quite insufficient for the hexadecapole anomaly explanation. The simultaneous inclusion of non-axial and hexadecapole degrees of freedom is found to be the most promising approach to explain the ''hexadecapole anomaly'' for Hf, W, Os isotopes. (author)

Some new approaches to the synthesis of heavy and superheavy elements

International Nuclear Information System (INIS)

Flerov, G.N.

1980-01-01

The results of work on the synthesis of heavy and superheavy elements are considered. It is shown that the new regularity of the systematics of spontaneous-fission half-lives, established for heavy nuclei at Dubna, has made it possible to extend the region of the nuclei being synthesized. In particular, it becomes possible to produce relatively long-lived heavy isotopes of Z>=107. The results of experiments to study the emission of energetic α-particles in the collision of heavy nuclei are presented. It is noted that such reactions can be used to produce atomic nuclei with low excitation energy and large angular momentum. The possible use of similar reactions in the synthesis of heavy and superheavy elements is discussed. In case the existence of a naturally occurring superheavy element has been established, a possibility will arise to synthesize in nuclear reactions a number of isotopes belonging to the island of stability, and to investigate their properties. The present state of work on the search for superheavy elements in nature is briefly described

Thermoluminescence mechanisms in CaSO4:Dy single crystals

International Nuclear Information System (INIS)

Morgan, M.D.; Stoebe, T.G.

1986-01-01

ESR studies of gamma-irradiated CaSO 4 :Dy have shown, in addition to the usual intrinsic defects, four new paramagnetic centres. An analysis of the g values and the g tensors in conjunction with the anhydrite crystal structure indicate that these centres are related to sulphate ions. Two of these centres (denoted 1a and 3a) are proposed as holes trapped and shared between two adjacent sulphate ions, this structure being stabilised by a neighbouring Ca vacancy. Centre 3b is suggested as a hole associated with one sulphate ion, again stabilised by an adjacent Ca vacancy. Because of the two distinct crystallographic directions in the anhydrite structure, centre 3b was found to consist of two distinguishable defects with slightly differing decay temperatures. The fourth centre appears to be an electron trapping site with structure similar to centre 3b. Decay temperatures of these ESR defects are correlated with the observance of TL peaks in CaSO 4 :Dy. Thermoluminescence studies as a function of impurity content confirmed the presence of calcium vacancies, which are formed during crystal growth, and that they play an important role in the TL process. TL models are proposed to account for the observed properties of CaSO 4 :Dy. (author)

Magnetic properties of melt-spun Nd-rich NdFeB alloys with Dy and Ga substitutions

International Nuclear Information System (INIS)

Harland, C.L.; Davies, H.A.

1998-01-01

The results of a systematic investigation of the effects of Dy and Ga additions on the magnetic properties of a Nd-rich NdFeB alloy are presented and discussed. Particular attention is given to the effect of increasing Dy substitutions on the coercivity of the Nd 18 Fe 76 B 6 alloy. Substitution of 30% of the Nd by Dy resulted in a coercivity increase from 1590 to 3290 kA m -1 . However, contrary to previous suggestions, substitution of 1% of the Fe by Ga was found to have only a small influence on the magnetic properties of all the alloys in the compositional series (Nd 100-x Dy x ) 18 Fe 76 B 6 (x=0-30). (orig.)

Validating PHITS for heavy ion fragmentation reactions

International Nuclear Information System (INIS)

Ronningen, Reginald M.

2015-01-01

The performance of the Monte Carlo code system PHITS is validated for heavy-ion transport capabilities by performing simulations and comparing results against experimental data from heavy-ion reactions of benchmark quality. These data are from measurements of isotope yields produced in the fragmentation of a 140 MeV/u "4"8Ca beam on a beryllium target and on a tantalum target. The results of this study show that PHITS performs reliably. (authors)

Down-shifting by energy transfer in Tb{sup 3+}/Dy{sup 3+} co-doped zinc phosphate glasses

Energy Technology Data Exchange (ETDEWEB)

Caldiño, U., E-mail: cald@xanum.uam.mx [Departamento de Física, Universidad Autónoma Metropolitana-Iztapalapa, P.O. Box 55-534, México, D.F. 09340 (Mexico); Muñoz H, G.; Camarillo, I. [Departamento de Física, Universidad Autónoma Metropolitana-Iztapalapa, P.O. Box 55-534, México, D.F. 09340 (Mexico); Speghini, A. [Dipartimento di Biotecnologie, Università di Verona, and INSTM, UdR Verona, Strada Le Grazie 15, I-37314 Verona (Italy); IFAC CNR, Nello Carrara Institute of Applied Physics, MDF Lab, I-50019 Sesto Fiorentino, FI (Italy); Bettinelli, M. [Dipartimento di Biotecnologie, Università di Verona, and INSTM, UdR Verona, Strada Le Grazie 15, I-37314 Verona (Italy)

2015-05-15

An optical spectroscopy investigation of zinc phosphate glasses activated with Tb{sup 3+}/Dy{sup 3+} ions is carried out through photoluminescence spectra and decay time measurements. The emission color can be adjusted from yellow–green light, with CIE1931 chromaticity coordinates (0.36,0.44), toward the white light region (0.35,0.39) by decreasing the Tb{sup 3+} content from 1.0 to 0.1 mol% of Tb(PO{sub 3}){sub 3} upon Dy{sup 3+} excitation at 423 nm. Such visible region luminescence is generated by {sup 5}D{sub 4}→{sup 7}F{sub 5} and {sup 5}D{sub 4}→{sup 7}F{sub 3} emissions of Tb{sup 3+} in addition to {sup 4}I{sub 15/2}→{sup 6}H{sub 15/2}, {sup 4}F{sub 9/2}→{sup 6}H{sub 15/2}, {sup 4}F{sub 9/2}→{sup 6}H{sub 13/2} and {sup 4}F{sub 9/2}→{sup 6}H{sub 11/2} emissions of Dy{sup 3+}, so that Tb{sup 3+} emission is sensitized by Dy{sup 3+} through a non-radiative resonant energy transfer. A dominant {sup 5}D{sub 4}→{sup 7}F{sub 5} green emission is observed in detriment of the {sup 5}D{sub 3}→{sup 7}F{sub J} blue emissions upon 282 nm excitation, as well as an extended excitation range (280–500 nm), due to multiple Dy{sup 3+} and Tb{sup 3+} transitions, which might contribute to enhance the spectral response of solar photovoltaic cells by down-shifting of the incident solar spectrum. - Highlights: • Zn(PO{sub 3}){sub 2} glasses are optically activated with Tb{sup 3+}/Dy{sup 3+} (ZPTbDy). • Non-radiative resonant energy transfer takes place between Tb{sup 3+} and Dy{sup 3+}. • Luminescence can be adjusted from yellow–green light toward the white light region. • ZPTbDy phosphor exhibits spectroscopic properties for photovoltaic applications.

High overexpression of dye decolorizing peroxidase TfuDyP leads to the incorporation of heme precursor protoporphyrin IX

NARCIS (Netherlands)

Colpa, Dana I.; Fraaije, Marco W.

2016-01-01

Highlights • Dye decolorizing peroxidase TfuDyP binds heme and protoporphyrin IX in vivo. • The activity of TfuDyP is dependent on the expression level in E. coli. • Expression of fully functional DyPs can be tuned by the type of expression host and expression conditions. The heterologous

Concentration-dependent luminescence and energy transfer of flower-like Y2(MoO4)3:Dy3+ phosphor

International Nuclear Information System (INIS)

Tian Yue; Chen Baojiu; Tian Bining; Hua Ruinian; Sun Jiashi; Cheng Lihong; Zhong Haiyang; Li Xiangping; Zhang Jinsu; Zheng Yanfeng; Yu Tingting; Huang Libo; Meng Qingyu

2011-01-01

Highlights: → Flower-shaped Y 2 (MoO 4 ) 3 phosphors were prepared by a co-precipitation method. → The structure and morphology of the prepared phosphors were characterized. → Energy transfer between Dy 3+ was studied by Huang's theory, IH and Uitert's models. - Abstract: Flower-like Y 2 (MoO 4 ) 3 :Dy 3+ phosphors have been synthesized via a co-precipitation approach with the aid of β-cyclodextrin. The crystal structure and morphology of the phosphors were characterized by XRD (X-ray diffraction) and FE-SEM (field emission scanning electron microscopy), respectively. The excitation and emission properties of the phosphors were examined by fluorescence spectroscopy. The dependence of color coordinates on the Dy 3+ doping concentration was analyzed. The energy transfer mechanism between Dy 3+ ions was studied based on the Huang's theory, I-H and Van Uitert's models. It was concluded simultaneously from these three routes that the electric dipole-dipole interaction between Dy 3+ ions is the main physical mechanism for the energy transfers between Dy 3+ .

High energy electron beams characterization using CaSO{sub 4}:Dy+PTFE Phosphors for clinical therapy applications

Energy Technology Data Exchange (ETDEWEB)

Rivera, T., E-mail: trivera@ipn.mx [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada-Legaria, IPN. Av. Legaria 694, Col. Irrigacion. 11500 Mexico DF (Mexico); Espinoza, A.; Von, S.M. [Centro Estatal de Cancerologia de los Servicios de Salud de Nayarit, Enfermeria S/n, Fracc, Fray Junipero Serra, 63169 Tepic Nay (Mexico); Alvarez, R.; Jimenez, Y. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada-Legaria, IPN. Av. Legaria 694, Col. Irrigacion. 11500 Mexico DF (Mexico)

2012-07-15

In the present work high energy electron beam dosimetry from linear accelerator (LINACs) for clinical applications using dysprosium doped calcium sulfate embedded in polytetrafluorethylene (CaSO{sub 4}:Dy+PTFE) was studied. The irradiations were carried out using high electron beams (6 to 18 MeV) from a linear accelerator (LINAC) Varian, CLINAC 2300C/D, for clinical practice purpose. The electron irradiations were obtained using the water solid in order to guarantee electronic equilibrium conditions (EEC). Field shaping for electron beams was obtained with electron cones. Glow curve and other thermoluminescent characteristics of CaSO{sub 4}:Dy+PTFE were conducted under high electrons beams irradiations. The TL response of the pellets showed an intensity peak centered at around 215 Degree-Sign C. TL response of CaSO{sub 4}:Dy+PTFE as a function of high electron absorbed dose showed a linearity in a wide range. To obtain reproducibility characteristic, a set of pellets were exposed repeatedly for the same electron absorbed dose. The results obtained in this study can suggest the applicability of CaSO{sub 4}:Dy+PTFE pellets for high electron beam dosimetry, provided fading is correctly accounted for. - Highlights: Black-Right-Pointing-Pointer Developing of CaSO{sub 4}:Dy to electron beams dosimetry. Black-Right-Pointing-Pointer Characterization of caSO{sub 4}:Dy to radiation safety in LINACs. Black-Right-Pointing-Pointer TL characteristics of CaSO{sub 4}:Dy for electron beams quality control.

Evaluation of nuclear reaction cross section of some isotopes of ...

African Journals Online (AJOL)

Coupled-channels optical model code OPTMAN is used as an alternative to experimental approach to evaluate the total reaction cross section for four different isotopes of Plutonium as an example of heavy rotational nuclei of the transuranium elements over an energy range of 10 to 20 MeV. The selected isotopes are the ...

Study of the giant dipole resonance built on highly excited states in Sn and Dy nuclei

International Nuclear Information System (INIS)

Stolk, A.

1988-01-01

A study is presented of the giant dipole resonance built on highly excited states. The aim is to get more detailed information on the properties of the GDR and to use it as a tool for the investigation of nuclear structure at high excitation energy. The high energy γ-rays seen from the decay of excited state GDRs in heavy ion fusion reactions reflect the average properties of the states populated by the γ-emission. The measurements at different initial excitation energies of 114 Sn provide information on the nuclear level density near the particle separation energy at an average angular momentum of 10ℎ. The study of shape changes at very high spin in 152-156 Dy nuclei is presented. A theoretical model developed to describe fusion-evaporation reactions is presented. 149 refs.; 63 figs.; 13 tabs

Preparation of {sup 166} Dy/{sup 166} Ho-Macro aggregates as an In vivo generator system for the treatment of arthrophaties; Preparacion de {sup 166} Dy/{sup 166} Ho-Macro agregados como un sistema de generador In vivo para el tratamiento de artropatias

Energy Technology Data Exchange (ETDEWEB)

Aldama A, T.K

2003-07-01

The present work reports the obtention of macro aggregates of hydroxides of Dysprosium-166/Holmium-166 ({sup 166} Dy/{sup 166} Ho-MH), as a generator system in vivo to be used in the treatment of arthritis rheumatoid. The {sup 166} Dy was obtained by neutron irradiation of {sup 166} DyO{sub 3} (enriched to 98.45%) by 20 h in the TRIGA Mark III Reactor and 50 h of decay, to the oxide of {sup 166} Dy/{sup 166} Ho formed, it was added HCl 0.12 N to obtain a final volume of 3.5 ml of solution of {sup 166} Dy/{sup 166} Ho chloride. The solution of {sup 166D}yCl{sub 3} solution was obtained with an activity of 3.502 mCi (129 MBq), appropriate for the preparation of the radiopharmaceutical {sup 166} Dy/{sup 166} Ho-MH. The separation of the {sup 166} Dy from the {sup 166} Ho, was carried out by chromatography in an cation exchange column, gaining an appropriate separation, obtaining a {sup 166} Dy with a radionuclide purity greater than 90%. The {sup 166} Dy/{sup 166} Ho-MH were prepared by addition to the solution of {sup 166} DyCI{sub 3} NaOH 0.5 N low ultrasonic bath with later centrifugation, decanted and resuspension in saline solution, obtaining a radiopharmaceutical with a generator system {sup 166} Dy/ {sup 166} Ho with particles of size average of 3 {mu}m, in form of {sup 166} Dy / {sup 166} Ho-MH. Under these conditions, it was obtained a radiochemical yield greater than 99%. The microscopic analysis and of filtration showed that the formulation doesn't present particles smaller than to 1 {mu}m, neither greater to 50 {mu}m, which will allow, the quick phagocytosis for the synoviocytes of the synovial membrane, and by consequence, an homogeneous distribution of the radiation dose could exist. The sedimentation velocity for the formulated suspension is of 0.04 cm/min that it will allow the administration of homogeneous activities of the radiopharmaceutical, to the no deposit in the injection devices. The studies of stability in vitro indicate us that inside

Preparation of {sup 166} Dy/{sup 166} Ho-Macro aggregates as an In vivo generator system for the treatment of arthrophaties; Preparacion de {sup 166} Dy/{sup 166} Ho-Macro agregados como un sistema de generador In vivo para el tratamiento de artropatias

Energy Technology Data Exchange (ETDEWEB)

Aldama A, T K

2003-07-01

The present work reports the obtention of macro aggregates of hydroxides of Dysprosium-166/Holmium-166 ({sup 166} Dy/{sup 166} Ho-MH), as a generator system in vivo to be used in the treatment of arthritis rheumatoid. The {sup 166} Dy was obtained by neutron irradiation of {sup 166} DyO{sub 3} (enriched to 98.45%) by 20 h in the TRIGA Mark III Reactor and 50 h of decay, to the oxide of {sup 166} Dy/{sup 166} Ho formed, it was added HCl 0.12 N to obtain a final volume of 3.5 ml of solution of {sup 166} Dy/{sup 166} Ho chloride. The solution of {sup 166D}yCl{sub 3} solution was obtained with an activity of 3.502 mCi (129 MBq), appropriate for the preparation of the radiopharmaceutical {sup 166} Dy/{sup 166} Ho-MH. The separation of the {sup 166} Dy from the {sup 166} Ho, was carried out by chromatography in an cation exchange column, gaining an appropriate separation, obtaining a {sup 166} Dy with a radionuclide purity greater than 90%. The {sup 166} Dy/{sup 166} Ho-MH were prepared by addition to the solution of {sup 166} DyCI{sub 3} NaOH 0.5 N low ultrasonic bath with later centrifugation, decanted and resuspension in saline solution, obtaining a radiopharmaceutical with a generator system {sup 166} Dy/ {sup 166} Ho with particles of size average of 3 {mu}m, in form of {sup 166} Dy / {sup 166} Ho-MH. Under these conditions, it was obtained a radiochemical yield greater than 99%. The microscopic analysis and of filtration showed that the formulation doesn't present particles smaller than to 1 {mu}m, neither greater to 50 {mu}m, which will allow, the quick phagocytosis for the synoviocytes of the synovial membrane, and by consequence, an homogeneous distribution of the radiation dose could exist. The sedimentation velocity for the formulated suspension is of 0.04 cm/min that it will allow the administration of homogeneous activities of the radiopharmaceutical, to the no deposit in the injection devices. The studies of stability in vitro indicate us that inside the

Single-phased CaAl2Si2O8:Tm3+, Dy3+ white-light phosphors under ultraviolet excitation

International Nuclear Information System (INIS)

Yang, Penghui; Yu, Xue; Xu, Xuhui; Jiang, Tingming; Yu, Hongling; Zhou, Dacheng; Yang, Zhengwen; Song, Zhiguo; Qiu, Jianbei

2013-01-01

A novel white-light-emitting phosphor CaAl 2 Si 2 O 8 :Tm, Dy was synthesized in ambient atmosphere by solid-state reaction. The energy transfer from Tm 3+ to Dy 3+ ions via a dipole–quadrupole reaction was observed and investigated. Upon UV excitation, white light emission was achieved by integrating a blue emission band located at 455 nm and an orange one located at 574 nm attributed to Tm 3+ and Dy 3+ ions, respectively. In addition, the energy-transfer efficiency and critical distance were calculated. Results suggested that the phosphor might be promising as a single-phased white-light-emitting phosphor for UV white-light LED. - Graphical abstract: The results indicate the existence of energy transfer from Tm 3+ to Dy 3+ . By tuning the concentration of Dy 3+ , single-phased white light can be realized. - Highlights: ► Energy transfer from Tm 3+ to Dy 3+ was investigated. ► Color tunable from blue to white can be achieved. ► White light can be realized in CaAl 2 Si 2 O 8 :Tm 3+ , Dy 3+ phosphor

Studies on the electrochemical behavior of heavy lanthanide ions and the synthesis, characterization of heavy metal chelate complexes

International Nuclear Information System (INIS)

Kang, Sam Woo; Chang, Choo Hwan; Son, Byung Chan; Suh, Moo Yul; Kim, Chae Kyun

1991-01-01

Electrochemical behavior of some heavy lanthanide ions(Gd 3+ , Tb 3+ , Dy 3+ , Ho 3+ , Er 3+ , Tm 3+ , Yb 3+ and Lu 3+ ) in various supporting electrolytes has been investigated by dc polarography, differential pulse polarography and cyclic voltammetry. The peak potentials and the peak currents, their dependency on the concentration and pH effects, the reversibility of the electrode reactions are described. The reduction of Gd 3+ , Tb 3+ , Dy 3+ , Ho 3+ , Er 3+ , Tm 3+ and Lu 3+ ions in 0.1M lithium chloride solution proceeds by a three-electron change directly to the metallic state, whereas the reduction of Yb 3+ proceeds by a one-electron change followed by a two-electron change. It was found that, in differential pulse polarography and cyclic voltammetry, the peak potential, peak current and current function showed constant value in the pH range of 4.0-6.0 by varying pH and scan rates. And also the current function is found to decrease as the sweep rate is increased when the pH reaches 4.0. This fact may indicate a chemical reaction coupled with the electrochemical reaction at lower pH values(pH 3+ ion is possible to determine voltammetrically within the error of ±3.5% in the presence of other competitive lanthanide ions. (Author)

Influence of Precursor Composition on the Microstructure and Superconducting Properties of Dy-Ba-Cu-O filaments

International Nuclear Information System (INIS)

Ikebe, Y; Ban, E; Matsuoka, Y; Nishijima, G; Watanabe, K

2006-01-01

Dy-Ba-Cu-O filaments have been successfully fabricated by a solution spinning method. The relationship between the partial melting temperature and the transport J c value at 77 K of the filamentary sample was systematically investigated. Two kinds of precursor filaments with starting composition of Dy:Ba:Cu = 1.18:2.12:3.09 (sample A)and Dy:Ba:Cu = 1.00:2.00:3.00 (sample B) were partially melted in 1%O 2 + Ar atmospheric gas and oxygenated in pure 100% O 2 gas. Samples partially melted at a wide temperature range of 990-1040 deg. C had J c values higher than 10 4 A/cm 2 . Both sample A and sample B partially melted at 1020 deg. C exhibited the maximum J c value higher than 4.2 x 10 4 A/cm 2 and 2.0 x 10 4 A/cm 2 , respectively. These samples had a dense microstructure consisting predominantly of Dy123 and finely dispersed Dy211 particles. The Dy211 particles with a diameter of about 1μm were finely dispersed in sample A, while the particles with a diameter of about 5μm were observed in sample B. The J c values of both samples were maintained about 2.0 x 10 3 A/cm 2 up to 14 T

Origin of the Moon Unveiled by its Heavy Iron Isotope Composition

Science.gov (United States)

Poitrasson, F.; Halliday, A. N.; Lee, D.; Levasseur, S.; Teutsch, N.

2002-12-01

The origin of the Moon has long been of interest and although the Giant Impact theory is currently the preferred explanation, unequivocal supporting evidence has been lacking. We have measured the iron isotope compositions of Shergotty-Nakhla-Chassigny meteorites and eucrites thought to come from Mars and Vesta, as well as samples from the Moon and the mafic Earth using high precision plasma source mass spectrometry. The mean iron isotope composition of the lunar samples, expressed in the conventional delta notation (d57Fe/54Fe) with respect to the IRMM-14 isotopic standard, is heavier (0.221 per mil (0.041: one standard deviation, 10 samples)) than those of the Earth (0.119 per mil (0.044, 7 samples)), which themselves are heavier than Martian meteorites (0.009 per mil (0.024, 6 samples)) and the eucrites measured (0.033 per mil (0.038, 7 samples)). Student's t-test calculations show that the Moon and Earth means are different from each other and from those of the other planetary bodies at >99% level of significance. The iron isotope compositions show no simple relationship with planetary heliocentric position, mantle oxygen fugacity, volatile content, or planet size. Similarly, these results do not support an origin of the Moon through co-accretion with the Earth, or as a fragment ejected from the Earth's mantle, or as another planet captured by the early Earth. In contrast, these data can be explained if the Earth, and especially the Moon, went through partial vaporisation and condensation leading to kinetic iron isotopic fractionation. Our data are also consistent with the suggested levels of enrichment of refractory elements for the bulk Earth and Moon. These new iron isotope results thus provide strong support for the origin of the Moon through a giant impact between the proto-Earth and another planet. Raleigh kinetic fractionation calculations indicate that only 1% loss of the current Fe budget of the Moon is required to explain its heavier isotopic

Mass spectrometric investigation of the isotopes of ozone in the laboratory and the stratosphere

International Nuclear Information System (INIS)

Mauersberger, K.; Morton, J.; Schueler, B.

1991-01-01

During the last few years information on the isotope anomalies of ozone has substantially increased. Whenever ozone is formed in a gas phase reaction, an enhancement in its heavy isotopes is found of magnitude 12-14% ( 50 O 3 ) above the statistically expected values. The mass-independent enhancement decreases toward higher pressures and also shows a pronounced temperature dependence. Toward lower temperatures the enhancement becomes less. Studies of all possible ozone isotopes have shown that molecular symmetry plays a major role. Even large enhancements, above the laboratory results, have been occasionally measured in the stratosphere using a number of different experimental techniques. A correlation between very high heavy ozone enhancement (> 30%) and high solar activity may exist. The behavior of ozone isotopes will provide information about the ozone formation process

Measurement of formation cross sections of short-lived nuclei by 14 MeV neutron. Nd, Sm, Dy, Er, Yb

Energy Technology Data Exchange (ETDEWEB)

Sakane, H.; Yamamoto, H.; Kawade, K. [Nagoya Univ. (Japan). School of Engineering; Iida, T.; Takahashi, A.

1997-03-01

Eight neutron activation cross sections producing the nuclei with half-lives between 3 min and 24 min were obtained at the energy range between 13.4 and 14.9 MeV by activation method. The cross sections were {sup 146}Nd(n,p){sup 146}Pr, {sup 154}Sm(n,{alpha}){sup 151}Nd, {sup 162}Dy(n,p){sup 162}Tb, {sup 163}Dy(n,np){sup 162}Tb, {sup 163}Dy(n,p){sup 163}Tb, {sup 164}Dy(n,p){sup 164}Tb, {sup 170}Er(n,{alpha}){sup 167}Dy, {sup 174}Yb(n,p){sup 170}Tm. {sup 163}Dy(n,np){sup 162}Tb (T{sub 1/2}=7.7 min) was obtained for the first time. Present results are compared with previous results and the evaluated data of JENDL-3 and ENDF/B-VI. There are some discrepancies between present results and the JENDL-3 and ENDF/B-VI. (author)

Effect Of DyMn Alloy-Powder Addition On Microstructure And Magnetic Properties Of NdFeB Sintered Magnets

Directory of Open Access Journals (Sweden)

Lee M.-W.

2015-06-01

Full Text Available Micostructural change and corresponding effect on coercivity of a NdFeB sintered magnet mixed with small amount of DyMn powder was investigated. In the sintered magnet mixed with the DyMn alloy-powder Dy-rich shell was formed at outer layer of the main grains, while Mn was mostly concentrated at Nd-rich triple junction phase (TJP, lowering melting temperature of the Nd-rich phase that eventually improved the microstructural characteristics of the gain boundary phase. The coercivity of a magnet increased more than 3.5 kOe by the mixing of the DyMn alloy-powder.

High electrical resistivity Nd-Fe-B die-upset magnet doped with eutectic DyF3–LiF salt mixture

Directory of Open Access Journals (Sweden)

K. M. Kim

2017-05-01

Full Text Available Nd-Fe-B-type die-upset magnet with high electrical resistivity was prepared by doping of eutectic DyF3–LiF salt mixture. Mixture of melt-spun Nd-Fe-B flakes (MQU-F: Nd13.6Fe73.6Co6.6Ga0.6B5.6 and eutectic binary (DyF3–LiF salt (25 mol% DyF3 – 75 mol% LiF was hot-pressed and then die-upset. By adding the eutectic salt mixture (> 4 wt%, electrical resistivity of the die-upset magnet was enhanced to over 400 μΩ.cm compared to 190 μΩ.cm of the un-doped magnet. Remarkable enhancement of the electrical resistivity was attributed to homogeneous and continuous coverage of the interface between flakes by the easily melted eutectic salt dielectric mixture. It was revealed that active substitution of the Nd atoms in neighboring flakes by the Dy atoms from the added (DyF3–LiF salt mixture had occurred during such a quick thermal processing of hot-pressing and die-upsetting. This Dy substitution led to coercivity enhancement in the die-upset magnet doped with the eutectic (DyF3–LiF salt mixture. Coercivity and remanence of the die-upset magnet doped with (DyF3–LiF salt mixture was as good as those of the DyF3-doped magnet.

The Effects of Dy Addition on Microstructure and Mechanical Properties of the As-Cast Mg-5Al-3Ca-2Nd Alloys.

Science.gov (United States)

Son, Hyeon-Taek; Kim, Yong-Ho; Yoo, Hyo-Sang

2018-03-01

The microstructure of the as-cast Mg-5Al-3Ca-2Nd-xDy alloys consists of α-Mg matrix, (Mg, Al)2Ca eutectic phase, Al-Nd and Al-Dy intermetallic compounds. α-Mg matrix morphology was changed from dendritic to equiaxed with the increase Dy addition. And grain size was remarkably refined. As Dy content was increased, yield strength was improved due to the refined grains and the homogeneous distribution of Al-Dy phase.

Yarn-dyed fabric defect classification based on convolutional neural network

Science.gov (United States)

Jing, Junfeng; Dong, Amei; Li, Pengfei; Zhang, Kaibing

2017-09-01

Considering that manual inspection of the yarn-dyed fabric can be time consuming and inefficient, we propose a yarn-dyed fabric defect classification method by using a convolutional neural network (CNN) based on a modified AlexNet. CNN shows powerful ability in performing feature extraction and fusion by simulating the learning mechanism of human brain. The local response normalization layers in AlexNet are replaced by the batch normalization layers, which can enhance both the computational efficiency and classification accuracy. In the training process of the network, the characteristics of the defect are extracted step by step and the essential features of the image can be obtained from the fusion of the edge details with several convolution operations. Then the max-pooling layers, the dropout layers, and the fully connected layers are employed in the classification model to reduce the computation cost and extract more precise features of the defective fabric. Finally, the results of the defect classification are predicted by the softmax function. The experimental results show promising performance with an acceptable average classification rate and strong robustness on yarn-dyed fabric defect classification.

Energy transfer and colorimetric properties of Eu3+/Dy3+ co-doped Gd2(MoO4)3 phosphors

International Nuclear Information System (INIS)

Wan Jing; Cheng Lihong; Sun Jiashi; Zhong Haiyang; Li Xiangping; Lu Weili; Tian Yue; Lin Hai; Chen Baojiu

2010-01-01

Dy 3+ single-doped and Eu 3+ /Dy 3+ co-doped gadolinium molybdate (Gd 2 (MoO 4 ) 3 ) phosphors were synthesized by a traditional solid-state reaction method. The XRD was used to confirm the crystal structure of the phosphors. The energy transfer between Eu 3+ and Dy 3+ was observed and studied. The Eu 3+ concentration can hardly affect the blue and yellow emission intensities of Dy 3+ , and the Eu 3+ emission intensity increases with the increase of Eu 3+ concentration. Co-doping with Eu 3+ compensated the red emission component of the Dy 3+ doped Gd 2 (MoO 4 ) 3 phosphor. Introducing proper amount of Eu 3+ can improve the colorimetric performance of the phosphors.

β-γ and isomeric decay spectroscopy of 168Dy

Directory of Open Access Journals (Sweden)

Zhang G.X.

2018-01-01

Full Text Available This contribution will report on the experimental work on the level structure of 168Dy. The experimental data have been taken as part of the EURICA decay spectroscopy campaign at RIBF, RIKEN in November 2014. In the experiment, a 238U primary beam is accelerated up to 345 MeV/u with an average intensity of 12 pnA. The nuclei of interest are produced by in-flight fission of 238U impinging on Be target with a thickness of 5 mm. The excited states of 168Dy have been populated through the decay from a newly identified isomeric state and via the β decay from 168Tb. In this contribution, scientific motivations, experimental procedure and some preliminary results for this study are presented.

Some properties of commercial dyed plastic as radiation dosimeters

International Nuclear Information System (INIS)

Rageh, M.S.I.; El-Assy, N.B.; Ashry, M.

1986-01-01

The use of commercial dyed plastics (red and green perspex) as radiation dosimeters in a cobalt-60 sterilizing plant is described. The results are satisfactory and offer advantages over the other dosimeters. The increase in the optical density for red perspex at wavelengths 650 and 750 nm with radiation can be used for absorbed dose measurements over the ranges from 1 to 7.5 KGy and from 5 to 25 KGy correspondingly. The decrease in the optical density for green perspex at 596, 612 and 641 nm with absorbed dose can extend the linear response range up to about 45 KGy. The fading of intensity of the irradiation induced absorption bands in dyed plastics after storage at different temperatures had been investigated

β-γ and isomeric decay spectroscopy of 168Dy

Science.gov (United States)

Zhang, G. X.; Watanabe, H.; Kondev, F. G.; Lane, G. J.; Regan, P. H.; Söderström, P.-A.; Walker, P. M.; Kanaoka, H.; Korkulu, Z.; Lee, P. S.; Liu, J. J.; Nishimura, S.; Wu, J.; Yagi, A.; Ahn, D. S.; Alharbi, T.; Baba, H.; Browne, F.; Bruce, A. M.; Carroll, R. J.; Chae, K. Y.; Dombradi, Zs.; Doornenbal, P.; Estrade, A.; Fukuda, N.; Griffin, C.; Ideguchi, E.; Inabe, N.; Isobe, T.; Kanaya, S.; Kojouharov, I.; Kubo, T.; Kubono, S.; Kurz, N.; Kuti, I.; Lalkovski, S.; Lee, C. S.; Lee, E. J.; Lorusso, G.; Lotay, G.; Moon, C.-B.; Nishizuka, I.; Nita, C. R.; Odahara, A.; Patel, Z.; Phong, V. H.; Podolyák, Zs.; Roberts, O. J.; Sakurai, H.; Schaffner, H.; Shand, C. M.; Shimizu, Y.; Sumikama, T.; Suzuki, H.; Takeda, H.; Terashima, S.; Vajta, Zs.; Valiente-Dóbon, J. J.; Xu, Z. Y.

2018-05-01

This contribution will report on the experimental work on the level structure of 168Dy. The experimental data have been taken as part of the EURICA decay spectroscopy campaign at RIBF, RIKEN in November 2014. In the experiment, a 238U primary beam is accelerated up to 345 MeV/u with an average intensity of 12 pnA. The nuclei of interest are produced by in-flight fission of 238U impinging on Be target with a thickness of 5 mm. The excited states of 168Dy have been populated through the decay from a newly identified isomeric state and via the β decay from 168Tb. In this contribution, scientific motivations, experimental procedure and some preliminary results for this study are presented.

The Structure of the Heavy Calcium Isotopes and the Effective Interaction in the sd-fp Shell

CERN Multimedia

Dorvaux, O; Nowacki, F; Courtin, S; Marechal, F; Siiskonen, T M; Perrot, F; Pietri, S B

2002-01-01

Nuclei with 40 $<$ A $<$ 56, near the stability line, are very well described in the frame of the shell model. However, when the number of neutrons increases, the situation becomes more complex which explains why the interaction can be found very dissimilar within different calculations. Heavy Ca isotopes, because of the simplicity of their wave-functions, correspond to the optimal choice to fix unambiguously the interaction in this mass region.\\\\ It is proposed to measure the $\\beta$-decay of $^{51, 52, 53}$K with the help of an utmost performing neutron (TONNERRE array) and $\\gamma$- (Miniball clusters) detection, allowing efficient coincidence measurements. This will allow the lowest lying Gamow-Teller states to be located in $^{51, 52, 53}$Ca, and the still unknown properties of natural parity states to be investigated. The awaited results should allow to settle the n-n interaction in the fp shell and the Gnp matrix accross the sd and fp shells, one step farther from stability, by comparison with fu...

Isolation and Sequence Analysis of HMW Glutenin Subunit 1Dy10.1 Ecoding Gene from Xinjiang Wheat (Triticum petropavlovskyi Udacz.et Migusch)

Institute of Scientific and Technical Information of China (English)

JIANG Qian-tao; WEI Yu-ming; WANG Ji-rui; YAN Ze-hong; ZHENG You-liang

2006-01-01

A novel HMW glutenin subunit gene 1Dy10.1 was isolated and characterized from Xinjiang wheat (Triticum petropavlovskyi. Udacz. et Migusch) accession Daomai 2. The complete open reading frame (ORF) of 1Dy10.1 was 1965 bp, encoding 655 amino acids. The numbers and distribution of cysteines in 1Dy10.1 were similar to those of 1Dy10 and other y-type subunits. In the N-terminal of 1Dy10.1, an amino acid was changed from L (leucine) to P (proline) at position 55. The repetitive domain of 1Dy10.1 differed from those of known HMW subunits by substitutions, insertions or/and deletions involving single or more amino acid residues. In the repetitive domain of subunit 1Dy10.1, the deletion of tripeptide GQQ in the consensus unit PGQGQQ resulted in the appearance of the motif PGQ that have not been observed in other known y-type HMW subunits. In comparison with the subunit 1Dy12, a deletion of dipeptide GQ, which occurred in subunit 1Dy10, was also observed in subunit 1Dy10.1. The cloned 1Dyl0.1 gene had been successfully expressed in Escherichia coli, and the expressed protein had the identical mobility with the endogenous subunit 1Dyl0.1 from seed.

Heavy-ion injector based on an electron cyclotron ion source for the superconducting linear accelerator of the Rare Isotope Science Project.

Science.gov (United States)

Hong, In-Seok; Kim, Yong-Hwan; Choi, Bong-Hyuk; Choi, Suk-Jin; Park, Bum-Sik; Jin, Hyun-Chang; Kim, Hye-Jin; Heo, Jeong-Il; Kim, Deok-Min; Jang, Ji-Ho

2016-02-01

The injector for the main driver linear accelerator of the Rare Isotope Science Project in Korea, has been developed to allow heavy ions up to uranium to be delivered to the inflight fragmentation system. The critical components of the injector are the superconducting electron cyclotron resonance (ECR) ion sources, the radio frequency quadrupole (RFQ), and matching systems for low and medium energy beams. We have built superconducting magnets for the ECR ion source, and a prototype with one segment of the RFQ structure, with the aim of developing a design that can satisfy our specifications, demonstrate stable operation, and prove results to compare the design simulation.

Utilization of stable isotopes for characterizing an underground gas generator

International Nuclear Information System (INIS)

Pirard, J.P.; Antenucci, D.; Renard, X.; Letolle, R.

1994-01-01

The principles of isotopic exchange and isotope ratio result interpretation are first reviewed; then, in the framework of an underground coal gasification project in Belgium, experiments and modelling of the underground gas generator have been carried out: isotopic abundances of carbon, hydrogen and oxygen have been measured in the gasifying agent (O 2 , H 2 O) and in the effluent (CO 2 , CO, H 2 , H 2 O, CH 4 , O 2 , heavy oils and various organic and mineral substances). Gasification kinetics and temperatures have been evaluated and isotope application to thermometry is discussed. 1 fig., 9 refs

New neutron-deficient isotopes of barium and rare-earth elements

CERN Document Server

Bogdanov, D D; Karnaukhov, V A; Petrov, L A; Plochocki, A; Subbotin, V G; Voboril, J

1976-01-01

The authors present an investigation of the short-lived neutron- deficient isotopes of barium and rare-earth elements. By using the BEMS-2 isotope separator on a heavy ion beam, 19 new isotopes were produced with mass numbers ranging from 117 to 138. Five of these (/sup 117/Ba, /sup 129,131/Nd and /sup 133,135/Sm) turned out to be delayed proton emitters. The beta -decay probabilities for the new isotopes have been analyzed in terms of the beta -strength function. An analysis of the proton spectrum shape has been performed using the statistical model for delayed proton emission.

Thermal, optical and structural properties of Dy3+ doped sodium aluminophosphate glasses

Science.gov (United States)

Kaur, Manpreet; Singh, Anupinder; Thakur, Vanita; Singh, Lakhwant

2016-03-01

Trivalent Dysprosium doped sodium aluminophosphate glasses with composition 50P2O5-10Al2O3-(20-x)Na2O-20CaO-xDy2O3 (x varying from 0 to 5 mol%) were prepared by melt quench technique. The density of the prepared samples was measured using Archimedes principle and various physical properties like molar volume, rare earth ion concentration, polaron radius, inter nuclear distance and field strength were calculated using different formulae. The differential scanning calorimetry (DSC) was carried out to study the thermal stability of prepared glasses. The UV Visible absorption spectra of the dysprosium doped glasses were found to be comprised of ten absorption bands which correspond to transitions from ground state 6H15/2 to various excited states. The indirect optical band gap energy of the samples was calculated by Tauc's plot and the optical energy was found to be attenuated with Dy3+ ions. The photoluminescence spectrum revealed that Dy3+ doped aluminophosphate glasses have strong emission bands in the visible region. A blue emission band centred at 486 nm, a bright yellow band centred at 575 nm and a weak red band centred at 668 nm were observed in the emission spectrum due to excitation at 352 nm wavelength. Both FTIR and Raman spectra assert slight structural changes induced in the host glass network with Dy3+ ions.

White light generation from Dy3+-doped yttrium aluminium gallium mixed garnet nano-powders

International Nuclear Information System (INIS)

Praveena, R.; Balasubrahmanyam, K.; Jyothi, L.; Venkataiah, G.; Basavapoornima, Ch.; Jayasankar, C.K.

2016-01-01

Yttrium aluminium gallium garnet (here after referred as YAGG), Y 3 Al 5−y Ga y O 12 (where y=1.0, 2.5 and 4.0), nano-powders doped with 1.0 mol% of dysprosium (Dy 3+ ) ions were synthesised by the citrate sol–gel method. The structure, phase evolution, morphology and luminescence properties of these nano-crytalline powders were characterized by means of XRD, FTIR, Raman, electron microscopy and UV–vis spectroscopy. From the XRD results, the crystallite sizes were found to be in the range of 18–26 nm. Excitation spectra of YAGG nano-powders showed that the samples can be efficiently excited by near UV and blue LEDs. Upon excitation at 448 nm, the emission spectra of all these samples showed two bands centred at 485 (blue) and 585 nm (yellow) which corresponds to the 4 F 9/2 → 6 H 15/2 and 4 F 9/2 → 6 H 13/2 transitions of Dy 3+ ion, respectively. Intensity of blue emission was found to be stronger than the yellow emission in all the three samples. Integrated yellow to blue (Y/B) emission intensity was found to be increased with increasing the Ga content in the present YAGG host. Therefore, concentration (0.1, 1.0, 2.0 and 4.0 mol%) of Dy 3+ ions was varied in the Ga rich (Y 3 Ga 4 AlO 12 ) nano-powder. The chromaticity co-ordinates of all the prepared nano-powders were located in the white light region and also found to be dependent on Dy 3+ ion concentration and excitation wavelength. The decay curves for 4 F 9/2 level of Dy 3+ ion exhibited non-exponential nature in all the studied samples and the lifetime values remained constant (~1.0 ms) with increasing the Ga content, but were found to decrease with increasing the Dy 3+ ion concentration. The results indicated that 2.0 mol% of Dy 3+ -doped Y 3 Ga 4 AlO 12 nano-powder under 352 nm excitation is suitable for the white light emitting device applications.

Thermoluminescence of LaAlO{sub 3}; Termoluminescencia de LaAlO{sub 3}:Dy

Energy Technology Data Exchange (ETDEWEB)

Morales H, A.; Zarate M, J. [Universidad Michoacana de San Nicolas de Hidalgo, Instituto de Investigacion en Metalurgia y Materiales, Ciudad Universitaria, Edif. U, 58060 Morelia, Michoacan (Mexico); Rivera M, T. [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Av. Legaria 694, 11500 Mexico D. F. (Mexico); Azorin N, J., E-mail: feyo_yo@hotmail.com [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Av. San Rafael Atlixco 186, Col. Vicentina, 09340 Mexico D. F. (Mexico)

2015-10-15

In this paper the thermoluminescent properties of doped lanthanum aluminate (LaAlO{sub 3}) with dysprosium ion (Dy) were studied. The thermoluminescence characteristics in the samples were obtained using an ultraviolet radiation of 220 nm. The LaAlO{sub 3}:Dy samples were prepared by the modified Pechini method (Spray Dryer). The structural and morphological characterization was obtained by X-ray diffraction (XRD) and scanning electron microscopy (Sem) techniques respectively. The size particle composing the agglomerate was determined by Sem, agglomerated particles composed size of 2μm were observed. The thermoluminescence response of LaAlO{sub 3}:Dy was compared with that obtained with the undoped sample. Thermoluminescence brightness curves of LaAlO{sub 3}:Dy showed a peak centered at 185 grades C. Sensitivity of doped sample was greater, about 100 times compared with the undoped sample. Thermoluminescence response in function of the wavelength showed a maximum at 220 nm. Also the fading in thermoluminescence response was studied. (Author)

Surface photo-discoloration and degradation of dyed wood veneer exposed to different wavelengths of artificial light

Energy Technology Data Exchange (ETDEWEB)

Liu, Yi [MOE Key Laboratory of Wooden Material Science and Application, Beijing Forestry University, Beijing 100083 (China); Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083 (China); MOE Engineering Research Center of Forestry Biomass Materials and Bioenergy, Beijing Forestry University, Beijing 100083 (China); Forest Products Development Center, School of Forestry and Wildlife Sciences, Auburn University, Auburn, AL 36830 (United States); Shao, Lingmin [MOE Key Laboratory of Wooden Material Science and Application, Beijing Forestry University, Beijing 100083 (China); Gao, Jianmin, E-mail: jmgao@bjfu.edu.cn [MOE Key Laboratory of Wooden Material Science and Application, Beijing Forestry University, Beijing 100083 (China); Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083 (China); MOE Engineering Research Center of Forestry Biomass Materials and Bioenergy, Beijing Forestry University, Beijing 100083 (China); Guo, Hongwu, E-mail: hwg5052@163.com [MOE Key Laboratory of Wooden Material Science and Application, Beijing Forestry University, Beijing 100083 (China); Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083 (China); MOE Engineering Research Center of Forestry Biomass Materials and Bioenergy, Beijing Forestry University, Beijing 100083 (China); Chen, Yao [MOE Key Laboratory of Wooden Material Science and Application, Beijing Forestry University, Beijing 100083 (China); Beijing Key Laboratory of Wood Science and Engineering, Beijing Forestry University, Beijing 100083 (China); MOE Engineering Research Center of Forestry Biomass Materials and Bioenergy, Beijing Forestry University, Beijing 100083 (China); Cheng, Qingzheng; Via, Brian K. [Forest Products Development Center, School of Forestry and Wildlife Sciences, Auburn University, Auburn, AL 36830 (United States)

2015-03-15

Highlights: • Investigate the selective absorption of different wavelengths of UV–vis light by dyed wood chromophores. • Identify connection between light wavelengths and surface color changes and chemical structure degradation. • Study hypochromic effect based on surface reflectance and K/S absorption changes during UV–vis irradiation. - Abstract: The surface of dyed wood is prone to discoloration when exposed to light irradiation which significantly decreases its decorative effect and shortens its service life. The influence of light wavelength exposure to the surface of dyed wood was investigated to study the effect on discoloration and degradation. Acid Blue V and Acid Red GR dyed wood veneers were subjected to light exposure with different wavelengths from the UV to visible region (254–420 nm). Results showed that the surface discoloration of dyed wood was linearly related to lignin concentration and dyes degradation and the consequent transformation of chromophoric groups such as aromatic (C=C) and carbonyl (C=O) through methoxy reaction. The dyes, lignin and some active constituents were degraded severely, even at short exposures. Acid Blue V dyed wood exhibited greater discoloration than the Acid Red GR treatment. The reflectance and K/S absorption curve showed a hypochromic effect on the dyed wood surface. The dyes and wood chemical structure played a complex and combined role on the selective absorption of different wavelengths of light. The color change rate was apparent with 254 nm exposure in the initial stages, but a greater discoloration rate occurred on the samples irradiated at 313 and 340 nm than at 254 and 420 nm with the time prolonged. The degradation rate and degree of discoloration correlated well with the light energy and wavelength.

Optical absorption, luminescence, and energy transfer processes studies for Dy3+/Tb3+-codoped borate glasses for solid-state lighting applications

Science.gov (United States)

Lakshminarayana, G.; Kaky, Kawa M.; Baki, S. O.; Lira, A.; Caldiño, U.; Kityk, I. V.; Mahdi, M. A.

2017-10-01

By using melt quenching technique, good optical quality singly doped Dy3+ or Tb3+ and Dy3+/Tb3+-codoped borate glasses were synthesized and studied by optical absorption, excitation, emission and decay lifetimes curve analysis. Following the absorption spectrum, the evaluated Judd-Ofelt (J-O) intensity parameters (Ωλ (λ = 2, 4 and 6)) were used to calculate the transition probability (AR), the branching ratio (βR), and the radiative lifetime (τR) for different luminescent transitions such as 4I15/2 → 6H15/2, 4F9/2 → 6H15/2, 4F9/2 → 6H13/2, 4F9/2 → 6H11/2 and 4F9/2 → 6H9/2,6F11/2 for the 0.5 mol % singly Dy3+-doped glass. The βR calculated (65%) indicates that for lasing applications, 4F9/2 → 6H13/2 emission transition is highly suitable. For all the Dy3+/Tb3+-codoped glasses, Tb3+: 5D3→7F6 emission decay lifetime curves are found to be non-exponential in nature for different concentrations of Dy3+ codoping. Using the Inokuti-Hirayama model, these nonexponential decay curves were analyzed to identify the nature of the energy transfer (ET) processes and here the electric dipole-dipole interaction is dominant for the ET. Based on the excitation and emission spectra and decay lifetimes curve analysis, the cross relaxation and ET processes between Dy3+ and Tb3+ were confirmed. For the 0.5 mol % Tb3+ and 2.0 mol % Dy3+-codoped glass, the evaluated Tb3+→Dy3+ ET efficiency (η) is found to be 45% under 369 nm excitation. Further, for Tb3+/Dy3+ -codoped glasses, an enhancement of Tb3+ green emission is observed up to 1.5 mol % Dy3+ codoping, and this is due to the non-radiative resonant ET from Dy3+ to Tb3+ upon 395 nm excitation. For singly 0.5 mol % Dy3+ or 0.5 mol % Tb3+-doped glass, the calculated color coordinates (x,y) and correlated color temperatures (CCT) represent the neutral white or warm white light regions, whereas Dy3+/Tb3+-codoped glasses (x,y) and CCT values fall in the yellowish green region with respect to the different Dy3

Production of 165 Dy for radiation synovectomy, in a low-power (slowpoke) nuclear reactor

International Nuclear Information System (INIS)

Bridges, C.; Duke, M.J.M.; McQuarrie, S.A.; Wiebe, L.I.

1998-01-01

Full text: Severe, debilitating pain accompanies inflammation of the synovial membrane in rheumatoid arthritis. Under certain conditions, radiation synovectomy is an effective alternative to surgery for relief of these symptoms. Radionuclides which decay by the emission of beta particles, or beta plus low yields of gamma/x-rays are indicated for this medical application. Of the radionuclides with appropriate decay emissions, half-life and physical/chemical properties, 165 Dy is a suitable candidate for production in a low-power reactor. Literature methods for production of this radiopharmaceutical usually involve irradiating solid Dy(OH) 3 , which is dissolved in HCl to form DyCl 3 and then re-precipitated under controlled conditions using NaOH, to produce the desired particle size for medical use. A procedure in which most or all of this post-irradiation processing can be eliminated is particularly important when using low neutron flux reactors, in order to avoid reductions in the amount of deliverable radiopharmaceutical. Radiological safety considerations may also necessitate avoiding post-irradiation processing, since low-power reactor facilities usually have no appropriate hot cells for extensive manipulation of highly active samples. Appropriately-sized, pre-formed Dy(OH) 3 particles were produced under a variety of conditions in attempts to produce a stable, sodium-free product that would be suitable for irradiation and use without further processing. Sodium content could be reduced to about 165 Dy production yields and particle characteristics will be presented in support of this concept

Magnetic and microstructural investigation of high-coercivity net-shape Nd–Fe–B-type magnets produced from spark-plasma-sintered melt-spun ribbons blended with DyF{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Žagar, Kristina, E-mail: kristina.zagar@ijs.si; Kocjan, Andraž; Kobe, Spomenka

2016-04-01

Nanostructured Nd–Fe–B-type materials produced by melt-spinning (MS) are used in a variety of applications in the electronics, automotive, and sensor industries. The very rapid MS process leads to flake-like powders with metastable, nanoscale, Nd{sub 2}Fe{sub 14}B grains. These powders are then formed into net-shaped, isotropic, polymer-bonded magnets, or they are hot formed into fully dense, metallic magnets that are isotropic and anisotropic. These fully dense magnets are usually produced with a conventional hot press without the inclusion of additives prior to the hot pressing. As a result, their properties, particularly the coercivity (H{sub ci}), are insufficient at automotive-relevant temperatures of 100–150 °C since the material H{sub ci} has a large temperature coefficient. In this study, we instead add a thin layer of DyF{sub 3} to the melt-spun ribbons prior to their hot consolidation in order to enhance the coercivity through a diffusion-based, partial substitution of the Nd by Dy. This is accomplished by applying extremely rapid, spark-plasma sintering to minimize any growth of the nanoscale Nd{sub 2}Fe{sub 14}B grains during consolidation. The result is a very high-coercivity magnet with drastically reduced amounts of heavy rare earths that is suitable for high-temperature applications. This work clearly demonstrates how rapidly formed, metastable states can provide us with properties that are unobtainable with conventional techniques. - Highlights: • We produced high coercivity magnets with drastically reduced amounts of HRE. • Microstructural analysis was conducted of the “free” and “wheel” side of Dy-treated Nd{sub 2}Fe{sub 14}B ribbons. • Dy-diffusion mechanism into ribbons depending on processing parameters is shown.

Nucleosynthesis of neutron-rich heavy nuclei during explosive helium burning in massive stars

International Nuclear Information System (INIS)

Blake, J.B.; Woosley, S.E.; Weaver, T.A.; Schramm, D.N.

1981-01-01

The production of heavy nuclei during explosive helium burning has been calculated using a hydrodynamical model of a 15 M/sub sun/ (Type II) supernovae and a n-process nuclear reaction network. The resulting neutron-rich heavy nuclei are not produced in the relative abundances of solar-system r-process material, especially in the vicinity of Pt, nor are any actinides produced. These deficiencies reflect an inadequate supply of neutrons. However, some neutron-rich isotopes, normally associated with the r-process, are produced which may be significant for the production of isotopic anomalies in meteorites

Lithium isotope effect during solvent extraction of LiCl with isoamyl alcohol

International Nuclear Information System (INIS)

Levkin, A.V.; Zhilov, V.I.; Marokin, O.V.; Demin, S.V.

1991-01-01

Method of extraction chromatography was used to measure the coefficient of lithium isotope separation (α) during extraction with isoamyl alcohol from concentrated LiCl aqueous solution. The α value is equal to 1.0036±0.0009; heavy 7 Li isotope is concentrated in organic phase at that

Study of the magnetic phase transitions and magnetocaloric effect in Dy{sub 2}Cu{sub 2}In compound

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yikun, E-mail: ykzhang10@hotmail.com [State Key Laboratory of Advanced Special Steels, Shanghai University, Shanghai, 200072 (China); Shanghai Key Laboratory of Advanced Ferrometallurgy, Shanghai University, Shanghai, 200072 (China); School of Materials Science and Engineering, Shanghai University, 200072 (China); Institute of Materials Physics, University of Münster, Wilhelm-Klemm-Straße 10, D-48149, Münster (Germany); Xu, Xiao; Yang, Yang; Hou, Long; Ren, Zhongming [State Key Laboratory of Advanced Special Steels, Shanghai University, Shanghai, 200072 (China); Shanghai Key Laboratory of Advanced Ferrometallurgy, Shanghai University, Shanghai, 200072 (China); School of Materials Science and Engineering, Shanghai University, 200072 (China); Li, Xi, E-mail: lx_net@sina.com [State Key Laboratory of Advanced Special Steels, Shanghai University, Shanghai, 200072 (China); Shanghai Key Laboratory of Advanced Ferrometallurgy, Shanghai University, Shanghai, 200072 (China); School of Materials Science and Engineering, Shanghai University, 200072 (China); Wilde, Gerhard [Institute of Materials Physics, University of Münster, Wilhelm-Klemm-Straße 10, D-48149, Münster (Germany)

2016-05-15

The magnetic properties and magnetocaloric effect (MCE) in Dy{sub 2}Cu{sub 2}In compound have been investigated. Dy{sub 2}Cu{sub 2}In undergoes two magnetic phase transitions, a paramagnetic to ferromagnetic (FM) at T{sub C} ∼ 49.5 K followed by a spin reorientation (SR) at T{sub SR} ∼ 19.5 K. For a magnetic field change of 0–7 T, the maximum values of the magnetic entropy change (−ΔS{sub M}{sup max}) are estimated to be 16.5 around T{sub C} and 6.7 J/kg K around T{sub SR} with a large relative cooling power (RCP) value of 617 J/kg. The modified Arrott plots and universal curves of the rescaled ΔS{sub M} confirmed that the magnetic phase transitions in Dy{sub 2}Cu{sub 2}In compound belongs the second order phase transitions. The present results may provide some clues to search for new magnetocaloric materials belonging to RE{sub 2}T{sub 2}X system. - Highlights: • Magnetic properties and magnetocaloric effect in Dy{sub 2}Cu{sub 2}In was studied. • The Dy{sub 2}Cu{sub 2}In undergoes 2 s order magnetic phase transitions. • A large reversible MCE was observed in Dy{sub 2}Cu{sub 2}In. • The origin of MCE and its potential application in Dy{sub 2}Cu{sub 2}In were discussed.

The effect of boron doping on crystal structure, magnetic properties and magnetocaloric effect of DyCo{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Wang, C.L., E-mail: wangchaolun2004@163.com [The Ames Laboratory U.S. Department of Energy, Iowa State University, Ames, IA 50011-3020 (United States); School of Materials Science and Engineering, University of Science and Technology of Beijing, Beijing 100083 (China); Liu, J. [The Ames Laboratory U.S. Department of Energy, Iowa State University, Ames, IA 50011-3020 (United States); Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011-2300 (United States); Mudryk, Y.; Gschneidner, K.A. [The Ames Laboratory U.S. Department of Energy, Iowa State University, Ames, IA 50011-3020 (United States); Long, Y. [School of Materials Science and Engineering, University of Science and Technology of Beijing, Beijing 100083 (China); Pecharsky, V.K. [The Ames Laboratory U.S. Department of Energy, Iowa State University, Ames, IA 50011-3020 (United States); Department of Materials Science and Engineering, Iowa State University, Ames, IA 50011-2300 (United States)

2016-05-01

The magnetic properties and magnetic entropy changes of DyCo{sub 2}B{sub x} (x=0, 0.05, 0.1, and 0.2) alloys were investigated. The Curie temperature (T{sub C}) increases with increasing B concentration. The frequency dependence of ac magnetic susceptibility of DyCo{sub 2} caused by the narrow domain wall pinning effect is depressed by B doping, but the coercivity and the magnetic viscosity are prominently increased in the B doped alloys. The magnetic transition nature of DyCo{sub 2}B{sub x} changes from the first-order to the second-order with increasing x, which leads to the decrease of the maximum magnetic entropy change. However, the relative cooling power (RCP) of DyCo{sub 2} and the B doped alloys remains nearly constant. - Highlights: • The discrepancy between the ZFC and FCC curves of DyCo{sub 2}B{sub x} is enhanced in the B doped samples, while the frequency dependence of the ac magnetic susceptibility is depressed. • The Curie temperature, coercivity and viscosity of DyCo{sub 2}B{sub x} are increased by B doping • The magnetic transition nature of the B doped samples is changed from first order to second order, leading to the decrease of magnetic entropy change. However, the relative cooling power of DyCo{sub 2}B{sub 0.05} is increased about 18%.

Thermoluminescent characteristics of CaSO{sub 4}:Dy+PTFE irradiated with high energy electron beams; Caracteristicas termoluminiscentes del CaSO{sub 4}:Dy+PTFE irradiado con haces de electrones de alta energia

Energy Technology Data Exchange (ETDEWEB)

Alvarez, R.; Rivera, T.; Calderon, J. A.; Jimenez, Y. [IPN, Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Av. Legaria 694, Col. Irrigacion, 11500 Mexico D. F. (Mexico); Rodriguez, J. [Hospital General de Mexico, Dr. Balmis 148, Col. Doctores, 06726 Mexico D. F. (Mexico); Oviedo, O. [Centro Medico ABC, Sur 136 No. 116, Col. Las Americas, 01120 Mexico D. F. (Mexico); Azorin, J., E-mail: chagua@hotmail.com [Universidad Autonoma Metropolitana, Unidad Iztapalapa, Av. San Rafael Atlixco 186, 09340 Mexico D. F. (Mexico)

2011-10-15

In the present work thermoluminescent response of dysprosium doped calcium sulfate embedded in polytetrafluorethylene (CaSO{sub 4}:Dy+PTFE) under high electron beam irradiations from linear accelerator for clinical applications was investigated. The irradiations were carried out using high electron beams (6 to 18 MeV) from a linear accelerator Varian, C linac 2300C/D, for clinical practice purpose. The electron irradiations were obtained by using the water solid in order to guarantee electronic equilibrium conditions. Field shaping for electron beams was obtained with electron cones. Glow curve and other thermoluminescent characteristics of CaSO{sub 4}:Dy+PTFE were conducted under high electron beams irradiations. The thermoluminescent response of the pellets showed and intensity peak centered at around 235 C. Thermoluminescent response of CaSO{sub 4}:Dy+PTFE as a function of high electron absorbed dose showed a linearity in a wide range. To obtain reproducibility characteristic, a set of pellets were exposed repeatedly for the same electron absorbed dose. The results obtained in this study can suggest the applicability of CaSO{sub 4}:Dy+PTFE pellets for high electron beam dosimetry, provided fading is correctly accounted for. (Author)

Coercivity enhancement mechanism in Dy-substituted Nd–Fe–B nanoparticles synthesized by sol–gel base method followed by a reduction-diffusion process

Energy Technology Data Exchange (ETDEWEB)

Rahimi, Hamed; Ghasemi, Ali, E-mail: ali13912001@yahoo.com; Mozaffarinia, Reza; Tavoosi, Majid

2017-05-01

In current work, Nd{sub 15−x}Dy{sub x}Fe{sub 77.5}B{sub 7.5} (at%) nanoparticles with different Dy-content (x=0.0, 0.5, 1.0, 1.5, 2.0, 2.5, 3.0) were synthesized by sol–gel method followed by a reduction-diffusion process. The effects of Dy on the magnetic properties and the relations between the microstructure and the coercivity of Dy-substituted Nd–Fe–B nanoparticles have been studied. The coercivity of Nd–Fe–B nanoparticles with the addition of Dy first increase, reaches a maximum, and then starts to decrease. The coercivity of Dy-substituted Nd–Fe–B nanoparticle synthesized by sol–gel method increased from 938.9 to 1663.9 kA/m while the remanence decreased slightly from 1.16 to 1.06 T. The results show that with an increase in Dy content the variation of maximum energy product ((BH){sub max}), lowest-order uniaxial magnetocrystalline anisotropy constant (K{sub u1}), and Curie temperature (T{sub c}) had a trend as same as the coercivity. The Henkel plot showed that the existence of exchange coupling interaction between grains, and the exchange coupling interactions increased with increasing x from 0.0 to 2.0 and then decrease with further increasing x≥2.5. The optimum magnetic properties of Nd–Fe–B nanoparticles with (BH){sub max} =40.38 MGOe, H{sub c}=1663.9 kA/m, B{sub r}=1.08 T were obtained by substituted 2.0 at% Dy. The effects of increasing temperature on magnetic properties of Dy-substituted Nd–Fe–B nanoparticle magnets with 2.0 at% Dy was investigated. The reduced spin-reorientation temperature was obtained for Dy-substituted Nd–Fe–B nanoparticles with 2.0 at% Dy. Below 100 K a spin-reorientation transition was takes place. The temperature coefficient of coercivity (β) was −0.36, −0.46, −0.41, −0.34, −0.29, −0.24, −0.25%/°C at different temperature 50, 100, 150, 200, 250, 300, 350 °C, respectively. Mössbauer spectroscopy was applied to study the composition and properties of Dy-substituted Nd�

Coercivity enhancement mechanism in Dy-substituted Nd–Fe–B nanoparticles synthesized by sol–gel base method followed by a reduction-diffusion process

International Nuclear Information System (INIS)

Rahimi, Hamed; Ghasemi, Ali; Mozaffarinia, Reza; Tavoosi, Majid

2017-01-01

In current work, Nd 15−x Dy x Fe 77.5 B 7.5 (at%) nanoparticles with different Dy-content (x=0.0, 0.5, 1.0, 1.5, 2.0, 2.5, 3.0) were synthesized by sol–gel method followed by a reduction-diffusion process. The effects of Dy on the magnetic properties and the relations between the microstructure and the coercivity of Dy-substituted Nd–Fe–B nanoparticles have been studied. The coercivity of Nd–Fe–B nanoparticles with the addition of Dy first increase, reaches a maximum, and then starts to decrease. The coercivity of Dy-substituted Nd–Fe–B nanoparticle synthesized by sol–gel method increased from 938.9 to 1663.9 kA/m while the remanence decreased slightly from 1.16 to 1.06 T. The results show that with an increase in Dy content the variation of maximum energy product ((BH) max ), lowest-order uniaxial magnetocrystalline anisotropy constant (K u1 ), and Curie temperature (T c ) had a trend as same as the coercivity. The Henkel plot showed that the existence of exchange coupling interaction between grains, and the exchange coupling interactions increased with increasing x from 0.0 to 2.0 and then decrease with further increasing x≥2.5. The optimum magnetic properties of Nd–Fe–B nanoparticles with (BH) max =40.38 MGOe, H c =1663.9 kA/m, B r =1.08 T were obtained by substituted 2.0 at% Dy. The effects of increasing temperature on magnetic properties of Dy-substituted Nd–Fe–B nanoparticle magnets with 2.0 at% Dy was investigated. The reduced spin-reorientation temperature was obtained for Dy-substituted Nd–Fe–B nanoparticles with 2.0 at% Dy. Below 100 K a spin-reorientation transition was takes place. The temperature coefficient of coercivity (β) was −0.36, −0.46, −0.41, −0.34, −0.29, −0.24, −0.25%/°C at different temperature 50, 100, 150, 200, 250, 300, 350 °C, respectively. Mössbauer spectroscopy was applied to study the composition and properties of Dy-substituted Nd–Fe–B magnet. Microstructure analysis showed a

Synthesis of CaF{sub 2}: dy for thermoluminescent dosimetry

Energy Technology Data Exchange (ETDEWEB)

Yamato, M.E.P.; Vasconcelos, D.A.A. de; Asfora, V.K.; Khoury, H.J.; Santos, R.A.; Barros, V.S.M., E-mail: mepyamato@gmail.com [Universidade Federal de Pernambuco (UFPE), Recife, PE (Brazil). Departamento de Energia Nuclear

2015-07-01

Calcium Fluoride doped with dysprosium is a known thermoluminescent material for applications that require highly sensitive dosimeters. Research in novel methods such as Combustion Synthesis (CS) has been ongoing for several years at the University of Pernambuco. The method uses the heat of the oxi-redox reaction a between nitrate and a fuel. This work presents results of CaF{sub 2}:Dy produced by combustion synthesis under different fabrication conditions. Samples were prepared by mixing stoichiometric amounts of calcium nitrate, urea and ammonium nitrate in a beaker under vigorous stirring. The resulting gel was transferred to a pre-heated muffle furnace were the combustion reaction occurred after a few minutes. For comparison, a variation of the production method with the same amounts of nitrate, ammonium fluoride and dopant, but without using the fuel was prepared. For both methods the resulting powder was pelleted and irradiated with Co-60 gamma radiation. The reproducibility and sensitivity for gamma dose irradiation was tested and results showed that optimum TL sample reproducibility was without the urea as fuel. Samples were then prepared with 0.05, 0.10, 0.15 and 0.20 mol% Dy concentration. The highest TL sensitivity was found for samples with 0.15 mol% Dy and sintered at 400 deg C for 3.5 h in air. The TL emission spectra, obtained using a Hammamatsu optical spectrometer, was comparable with commercial CaF{sub 2}:Dy. Thermoluminescence was measured in a Harshaw-Bicron 3500 TL Reader. The glow curve showed stable dosimetric peaks at around 200, 235 and 300 deg C were a linear dose response curve was obtained for the range 100 mGy to 1000 mGy. (author)

Effect of trivalent transition metal ion substitution in Dy2O3 system

International Nuclear Information System (INIS)

Dhilip, M.; Saravana Kumar, K.; Anbarasu, V.

2015-01-01

One of the very promising approaches to create novel materials is to combine different physical properties in one material to achieve rich functionality. Magnetoelectric multiferroics are attracting attention for fundamental physics due to their unique coupling behaviour between ferroelectricity, ferromagnetism and ferroelasticity and also because of their promising applications for devices in spintronics, information storage, sensing and actuation. The existence of spontaneous magnetization in the perovskite like phase (layer of perovskite) has encouraged exploring the possibility of fabrication of a multiferroic material for multifunctional devices using the concept of magnetoelectric effect. The rare earth orthoferrites (LnFeO 3 where, Ln = La, Sm, Gd, Dy, Er and Yb) are a class of materials having potential for various applications. These compounds and metal ion substituted ferrites crystallising in perovskite structure show promise as catalysts gas separators, cathodes in solid oxide fuel cells, sensor materials, magneto-optic materials and as spin valves. In this present work, Fe substituted in Dysprosium Oxide compounds were prepared by standard solid state reaction at a temperature of 1300℃. The structural analysis of the prepared samples was characterized with powder X-Ray Diffraction technique and the lattice parameters were calculated with PodwerX indexing software. The structural analysis reveals that the substitution of Fe in Dy 2 O 3 system leads to change of crystalline structure from Cubic to Tetragonal. Further, decreasing trend of volume of the unit cell confirms the occupation of smaller ionic radii element Fe in the Dy site of Dy 2 O 3 system. Hence the possibilities of incorporation of trivalent transition metal ion in to the host Dy 2 O 3 site were analyzed. (author)

New intermetallic compounds Ln(Ag, AL)4 (Ln-Y, Gd, Tb, Dy) and their structure

International Nuclear Information System (INIS)

Kuz'ma, Yu.B.; Stel'makhovich, B.M.

1990-01-01

By the methods of X-ray analysis crystal structure of compounds Ln(Ag,Al) 4 , where Ln-Y, Gd, Tb, Dy, posessing rhombic structure, is determined. The intermetallics have been prepared for the first time. Ways of atom distribution and their coordinates in DyAg 0.55 Al 3.45 structure (a=0.4296(1), b=04179(1), c=0.9995(3), R=0.093) are specified. Other compounds are formed in case of LnAgAl 3 compositions. Interatomic distances in Dy(Ag,Al) 4 structure are considered. A supposition is made on the formation in Ln-Ag-Al systems of a greater number of intermetallic compounds

Thermoluminescence of CaCO3:Dy and CaCO3:Mn

International Nuclear Information System (INIS)

Bapat, V.N.; Nambi, K.S.V.

1976-01-01

CaCO 3 samples doped with Dy and Mn were prepared in the laboratory by co-precipitation techniques. Thermoluminescence and emission spectra of these phosphors were studied and were compared with those of the naturally occuring calcite and undoped CaCO 3 samples. Dy-doping seems to give a more efficient phosphor and indicates a possibility of getting a better phosphor by a judicious choice of a rare earth doping of CaCO 3 . Interesting result have been obtained on the TL glow curve variations of these phosphors with different temperature treatments prior to irradiation. (author)

Progress in sintered NdFeB magnets with Dy/Tb grain boundary diffusion%晶界扩散Dy/Tb烧结NdFeB研究进展

Institute of Scientific and Technical Information of China (English)

刘涛; 周磊; 张昕; 程星华; 林德; 喻晓军; 李波

2011-01-01

由于汽车和电子应用领域对节能电动机的需求,在VCM、电动机、信号发生器、手机和MRI等领域中得到广泛应用的烧结钕铁硼在电动机市场应用会进一步扩展.剩磁和矫顽力等磁性能的提高有利于烧结磁体在电动机市场快速增长.通常,烧结磁体一些性能的改善总是以牺牲其他性能为代价.而晶界扩散Dy/Tb烧结磁体与传统的同类磁体相比较,其矫顽力和剩磁可同时得以改善,本文对晶界扩散Dy/Tb钕铁硼的一些研究成果进行了综述和总结.晶界扩散Dy/Tb过程中烧结磁体晶界的成份和微观组织的变化对烧结磁体磁性能改善至为重要.%Many new applications of Nd-Fe-B magnets, such as voice coil motor (VCM) in hard disc drive, motors, generators, mobile phone, MRI, etc, are expected to expand in future because of strong energy saving requirements from the automobile and electric appliances markets. Magnetic property improvement in residual (Br) and coercive force (Hcj) helps the rapid growth of the motor market. In many instances, an improvement of some characteristics of sintered magnet is achieved but only at the expense of other characteristics. It has been found that Dy/Tb grain boundary diffusion processed Nd-Fe-B sintered magnets have improvement in both the highest remanence and cocercivity among conventional rare-earth permanent mgnets, which have been introduced in this paper. The influence of Dy/Tb grain boundary diffusion on composition and microstructure of grain boundaries phase is a key point for magnetic property improvement of sintered magnet.

Numerical analysis and optimisation of heavy water upgrading column

International Nuclear Information System (INIS)

Sankar, Rama; Ghosh, Brindaban; Bhanja, K.

2013-01-01

In the 'Pressurised Heavy Water' type of reactors, heavy water is used both as moderator and coolant. During operation of reactor downgraded heavy water is generated that needs to be upgraded for reuse in the reactor. When the isotopic purity of heavy water becomes less than 99.75%, it is termed as downgraded heavy water. Downgraded heavy water also contains impurity such as corrosion products, dirt, oil etc. Upgradation of downgraded heavy water is normally done in two steps: (i) Purification: In this step downgraded heavy water is first purified to remove corrosion products, dirt, oil, etc. and (ii) Upgradation of heavy water to increase its isotopic purity, this step is carried out by vacuum distillation of downgraded heavy water after purification. This project is aimed at mathematical modelling and numerical simulation of heavy water upgrading column. Modelling and simulation studies of the upgradation column are based on equilibrium stage model to evaluate the effect of feed location, pressure, feed composition, reflux ratio in the packed column for given reboiler and condenser duty of distillation column. State to stage modelling of two-phase two-component flow has constitutes the overall modelling of the column. The governing equations consist of stage-wise species and overall mass continuity and stage-wise energy balance. This results in tridigonal matrix equation for stage liquid fractions for heavy and light water. The stage-wise liquid flow rates and temperatures are governed by stage-wise mass and energy balance. The combined form of the corresponding governing equations, with the incorporation of thermodynamic equation of states, form a system of nonlinear equations. This system have been resolved numerically using modified Newton-Raphson method. A code in the MATLAB platform has been developed by on above numerical procedure. The optimisation of the column operating conditions is to be carried out based on parametric studies and analysis of different

Preliminary Shielding Assessment for the IFF System in the RAON Heavy-ion Facility

International Nuclear Information System (INIS)

Lee, Cheol Woo; Lee, Youngouk; Kim, Jong Won; Kim, Mijung

2014-01-01

A heavy-ion accelerator facility is under a development in Korea to use in the basic science research and various application areas. In this facility, the In-Flight Fragment (IFF) target and isotope separator has been designed to produce various isotopes and transport the interesting isotopes into the experimental rooms. In this work, preliminary radiation shielding assessment was performed for the IFF target room

Basic atomic interactions of accelerated heavy ions in matter atomic interactions of heavy ions

CERN Document Server

Tolstikhina, Inga; Winckler, Nicolas; Shevelko, Viacheslav

2018-01-01

This book provides an overview of the recent experimental and theoretical results on interactions of heavy ions with gaseous, solid and plasma targets from the perspective of atomic physics. The topics discussed comprise stopping power, multiple-electron loss and capture processes, equilibrium and non-equilibrium charge-state fractions in penetration of fast ion beams through matter including relativistic domain. It also addresses mean charge-states and equilibrium target thickness in ion-beam penetrations, isotope effects in low-energy electron capture, lifetimes of heavy ion beams, semi-empirical formulae for effective cross sections. The book is intended for researchers and graduate students working in atomic, plasma and accelerator physics.

Radiographic Co-60 in component of heavy equipment casting

International Nuclear Information System (INIS)

Djoli Soembogo, Harun Al Rasyid R dan Namad Sianta

2016-01-01

The application of radiography using isotope Co-60 source has been used on component of heavy equipment such as component of heavy equipment casting. Components of heavy equipment casting made through metal casting of carbon steel. This study tried applying digital radiography are using isotope Co-60 sources and using scanning positive film media of Epson V700 for digitization results of conventional radiographic films. This radiography is using film AGFA D7 and Fuji 100 to obtain a contrast medium, medium sensitivity and image quality is good. The purpose radiographic Co-60 at a component of heavy equipment casting is detecting indications of the shape and type casting defects of component of heavy equipment casting thus fit for use. Radiographic test of Co-60 has been carried out on component of heavy equipment casting with single wall single image method and the results of radiographic films digitization using scanning positive film media of Epson V700 with observation parameters casting defects. Time exposure of Co-60 radiation was 10 and 15 minutes hours for metal castings of carbon steel for thickness 20.00-50.00 mm by using activity 30.05 Ci and the perpendicular distance to the source of the film is 820 mm. Scanner positive film results in the form of digital radiography which allow for the transfer of digital data or digital computerized data storage. Radiographic test results on component of heavy equipment casting with single wall single image method produce the parameter casting defect of component of heavy equipment casting in position of critical area is found shrinkage that should be repaired and in position of safety area is not found defect indication so casting defect of component of heavy equipment casting are not acceptable according to standards referenced. (author)

K isomerism and collectivity in neutron-rich rare-earth isotopes.

OpenAIRE

Patel, Zena

2016-01-01

Neutron-rich rare-earth isotopes were produced by in-flight fission of 238U ions at the Radioactive Isotope Beam Factory (RIBF), RIKEN, Japan. In-flight fission of a heavy, high-intensity beam of 238U ions on a light target provides the cleanest secondary beams of neutron-rich nuclei in the rare-earth region of isotopes. In-flight fission is advantageous over other methods of nuclear production, as it allows for a secondary beam to be extracted, from which the beam species can be separated an...

Frontiers of heavy element nuclear and radiochemistry

International Nuclear Information System (INIS)

Hoffman, D.C.

1999-01-01

The production and half-lives of the heaviest chemical elements, now known through Z=112, are reviewed. Recent experimental evidence for the stabilization of heavy element isotopes due to proximity to deformed nuclear shells at Z=108 and N=162 is compared with the theoretical predictions. The possible existence of isotopes of elements 107-110 with half-lives of seconds or longer, and production reactions and experimental techniques for increasing the overall yields of such isotopes in order to study both their nuclear and chemical properties are discussed. The present status of studies of the chemical properties of Rf, Ha, and Sg is briefly summarized and prospects for extending chemical studies beyond Sg are considered. (author)

Ab initio study of double perovskites Ba_2DySbO_6

International Nuclear Information System (INIS)

Jha, Dhiraj Kumar; Mandal, Golak; Singh, B. K.; Ray, Chandan; Himanshu, A. K.; Kumar, Uday; Choudhary, B. K.

2016-01-01

First principle study of the electronic band structure of Ba2DySbO_6 synthesied by the solid state reaction technique have been performed within the framework of density function theory using WIEN2K. It has been shown in the absence of electron-electron interaction (U=0), BaDySO_6 behaves like a half-metal. Even in the presence of DFT+U, electron-electron interaction via the Hubbard term (from U = 0, 2.72e -7.02 eV), it still shows half metals.

Stable isotope composition of mercury forms in flue gases from a typical coal-fired power plant, Inner Mongolia, northern China

International Nuclear Information System (INIS)

Tang, Shunlin; Feng, Chaohui; Feng, Xinbin; Zhu, Jianming; Sun, Ruoyu; Fan, Huipeng; Wang, Lina; Li, Ruiyang; Mao, Tonghua; Zhou, Ting

2017-01-01

Highlights: • The first speciated Hg isotope ratios in coal combustion flue gases are presented. • Significant Hg isotope kinetic MDF was observed during Hg forms transformation. • Emitted gaseous Hg highly enriches in heavy Hg isotopes relative to feed coal. - Abstract: Mercury forms emitted from coal combustion via air pollution control devices are speculated to carry different Hg isotope signatures. Yet, their Hg isotope composition is still not reported. Here, we present the first onsite Hg isotope data for gaseous elemental Hg (GEM) and gaseous oxidized Hg (GOM) of flue gases from a typical lignite-fired power plant (CFPP). Significant mass dependent fractionation (MDF) and insignificant mass independent fractionation (MIF) are observed between feed coal and coal combustion products. As compared to feed coal (δ 202 Hg = −2.04 ± 0.25‰), bottom ash, GEM and GOM in flue gases before and after wet flue gas desulfurization system significantly enrich heavy Hg isotopes by 0.7–2.6‰ in δ 202 Hg, while fly ash, desulfurization gypsum and waste water show slight but insignificant enrichment of light Hg isotopes. GEM is significantly enriched heavy Hg isotopes compared to GOM and Hg in fly ash. Our observations verify the previous speculation on Hg isotope fractionation mechanism in CFPPs, and suggest a kinetically-controlled mass dependent Hg isotope fractionation during transformation of Hg forms in flue gases. Finally, our data are compared to Hg isotope compositions of atmospheric Hg pools, suggesting that coal combustion Hg emission is likely an important atmospheric Hg contributor.

Stable isotope composition of mercury forms in flue gases from a typical coal-fired power plant, Inner Mongolia, northern China

Energy Technology Data Exchange (ETDEWEB)

Tang, Shunlin, E-mail: tangshunlin@hpu.edu.cn [Institute of Resources and Environment, Henan Polytechnic University, Jiaozuo, Henan Province, 454000 (China); Feng, Chaohui [Institute of Resources and Environment, Henan Polytechnic University, Jiaozuo, Henan Province, 454000 (China); Feng, Xinbin [State Key Laboratory of Environmental Geochemistry, Institute of Geochemistry, Chinese Academy of Sciences, Guiyang, 550002 (China); Zhu, Jianming [Institute of Resources and Environment, Henan Polytechnic University, Jiaozuo, Henan Province, 454000 (China); State Key Laboratory of Geological Processes and Mineral Resources, China University of Geosciences, Beijing, 100086 (China); Sun, Ruoyu, E-mail: ruoyu.sun@tju.edu.cn [CAS Key Laboratory of Crust-Mantle Materials and Environment, School of Earth and Space Sciences, University of Science and Technology of China, Hefei, Anhui 230026 (China); Fan, Huipeng; Wang, Lina; Li, Ruiyang; Mao, Tonghua [Institute of Resources and Environment, Henan Polytechnic University, Jiaozuo, Henan Province, 454000 (China); Zhou, Ting [State Key Laboratory of Ore Deposit Geochemistry, Institute of Geochemistry, Chinese Academy of Sciences, Guiyang, 550002 (China)

2017-04-15

Highlights: • The first speciated Hg isotope ratios in coal combustion flue gases are presented. • Significant Hg isotope kinetic MDF was observed during Hg forms transformation. • Emitted gaseous Hg highly enriches in heavy Hg isotopes relative to feed coal. - Abstract: Mercury forms emitted from coal combustion via air pollution control devices are speculated to carry different Hg isotope signatures. Yet, their Hg isotope composition is still not reported. Here, we present the first onsite Hg isotope data for gaseous elemental Hg (GEM) and gaseous oxidized Hg (GOM) of flue gases from a typical lignite-fired power plant (CFPP). Significant mass dependent fractionation (MDF) and insignificant mass independent fractionation (MIF) are observed between feed coal and coal combustion products. As compared to feed coal (δ{sup 202}Hg = −2.04 ± 0.25‰), bottom ash, GEM and GOM in flue gases before and after wet flue gas desulfurization system significantly enrich heavy Hg isotopes by 0.7–2.6‰ in δ{sup 202}Hg, while fly ash, desulfurization gypsum and waste water show slight but insignificant enrichment of light Hg isotopes. GEM is significantly enriched heavy Hg isotopes compared to GOM and Hg in fly ash. Our observations verify the previous speculation on Hg isotope fractionation mechanism in CFPPs, and suggest a kinetically-controlled mass dependent Hg isotope fractionation during transformation of Hg forms in flue gases. Finally, our data are compared to Hg isotope compositions of atmospheric Hg pools, suggesting that coal combustion Hg emission is likely an important atmospheric Hg contributor.

Thermal characterization of (U, Dy)O2 pellets

International Nuclear Information System (INIS)

Pelloni, M; Bianchi, L; Pablovich, M.E; Kaufmann, F; Kempf, R

2012-01-01

The thermal diffusivity of (U,Dy)O 2 pellets were determined in the temperature range 250 K to 1600 K measured by the laser flash method. The dependence of thermal with temperature and dysprosium content was studied and found in good agreement with physical models available (author)

Thermoluminescent characteristics of CaSO4:Dy+PTFE irradiated with high energy electron beams

International Nuclear Information System (INIS)

Alvarez, R.; Rivera, T.; Calderon, J. A.; Jimenez, Y.; Rodriguez, J.; Oviedo, O.; Azorin, J.

2011-10-01

In the present work thermoluminescent response of dysprosium doped calcium sulfate embedded in polytetrafluorethylene (CaSO 4 :Dy+PTFE) under high electron beam irradiations from linear accelerator for clinical applications was investigated. The irradiations were carried out using high electron beams (6 to 18 MeV) from a linear accelerator Varian, C linac 2300C/D, for clinical practice purpose. The electron irradiations were obtained by using the water solid in order to guarantee electronic equilibrium conditions. Field shaping for electron beams was obtained with electron cones. Glow curve and other thermoluminescent characteristics of CaSO 4 :Dy+PTFE were conducted under high electron beams irradiations. The thermoluminescent response of the pellets showed and intensity peak centered at around 235 C. Thermoluminescent response of CaSO 4 :Dy+PTFE as a function of high electron absorbed dose showed a linearity in a wide range. To obtain reproducibility characteristic, a set of pellets were exposed repeatedly for the same electron absorbed dose. The results obtained in this study can suggest the applicability of CaSO 4 :Dy+PTFE pellets for high electron beam dosimetry, provided fading is correctly accounted for. (Author)

Resonant X-ray emission spectroscopy in Dy compounds

International Nuclear Information System (INIS)

Tanaka, Satoshi; Okada, Kozo; Kotani, Akio.

1994-01-01

The excitation spectrum of the L 3 -M 5 X-ray emission of Dy compounds in the pre-edge region of Dy L 3 X-ray absorption near edge structure (L 3 -XANES) is theoretically investigated based upon the coherent second order optical formula with multiplet coupling effects. The spectral broadening of the excitation spectrum is determined by the M 5 core hole lifetime, being free from the L 3 core hole lifetime. The fine pre-edge structure of the L 3 edge due to the 2p→4f quadrupole transition can be seen in the excitation spectrum, while this structure is invisible in the conventional XANES, in agreement with the recent experimental results. We clarify the conditions for the excitation spectrum to be regarded as the absorption spectrum with a smaller width. The resonant X-ray emission spectra for various incident photon energies around the L 3 edge are also calculated. (author)

Isotopic fingerprint of the middle Olt River basin, Romania.

Science.gov (United States)

Popescu, Raluca; Costinel, Diana; Ionete, Roxana Elena; Axente, Damian

2014-01-01

One of the most important tributaries of the Danube River in Romania, the Olt River, was characterized in its middle catchment in terms of the isotopic composition using continuous flow-isotope ratio mass spectrometry (CF-IRMS). Throughout a period of 10 months, from November 2010 to August 2011, water samples from the Olt River and its more important tributaries were collected in order to investigate the seasonal and spatial isotope patterns of the basin waters. The results revealed a significant difference between the Olt River and its tributaries, by the fact that the Olt River waters show smaller seasonal variations in the stable isotopic composition and are more depleted in (18)O and (2)H. The waters present an overall enrichment in heavy isotopes during the warm seasons.

Synthesis, characterization and photoluminescence properties of Dy{sup 3+}-doped nano-crystalline SnO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Pillai, Sreejarani K.; Sikhwivhilu, Lucky M. [National Centre for Nano-Structured Materials, CSIR, PO Box 395, Pretoria 0001 (South Africa); Hillie, Thembela K., E-mail: thillie@csir.co.za [National Centre for Nano-Structured Materials, CSIR, PO Box 395, Pretoria 0001 (South Africa); Physics Department, University of the Free State, P.O. Box 339, Bloemfontein 9300 (South Africa)

2010-04-15

Nano-crystalline of tin oxide doped with varying wt% of Dy{sup 3+} was prepared using chemical co-precipitation method and characterised by various advanced techniques such as BET-surface area, Fourier transform infrared spectroscopy, X-ray diffraction, Raman spectroscopy and photoluminescence measurements. Analytical results demonstrated that the nanocrystalline tin oxide is in tetragonal crystalline phase and doping with Dy{sup 3+} could inhibit the phase transformation, increases surface area and decreases the crystallite size. The experimental result on photoluminescence characteristics originating from Dy{sup 3+}-doping in nanocrystalline SnO{sub 2} reveals the dependence of the luminescent intensity on dopant concentration.

Optical and structural investigation of Dy3+-Nd3+ co-doped in magnesium lead borosilicate glasses.

Science.gov (United States)

Rao, T G V M; Rupesh Kumar, A; Neeraja, K; Veeraiah, N; Rami Reddy, M

2014-01-24

MgO-PbO-B2O3-SiO2-Nd2O3-Dy2O3 glasses are prepared by melt-quenching technique. The samples are characterized by X-ray diffraction (XRD), optical absorption, luminescence and Fourier transform infrared (FT-IR) spectral studied. XRD analysis evidently indicates that the prepared samples are fully amorphous nature. From the optical absorption spectra, the bonding environment surrounding the Dy(3+) and their energy level scheme in glass network is analyzed. Enhancement of Dy(3+) emission by non-radiative energy transfers from Nd(3+) has been observed here. The samples emits intensive bluish yellow color from the (4)F9/2→(6)H15/2, (6)H13/2 transition of Dy(3+) ions in these glasses which are nearer to white light and it is also supported by the chromaticity color coordinates. The FT-IR spectra reveal that network connectivity is increased with replacement of bonds B-O-B, Si-O-Si by more resistant B-O-Si bonds with gradually increasing the content of Dy(3+) ions in the glass network. Along with spectroscopic parameters some physical parameters like density, refractive index etc. are measured for the glasses. Copyright © 2013 Elsevier B.V. All rights reserved.

Combined electrolysis catalytic exchange (CECE) process for hydrogen isotope separation

International Nuclear Information System (INIS)

Hammerli, M.; Stevens, W.H.; Butler, J.P.

1978-01-01

Hydrogen isotopes can be separated efficiently by a process which combines an electrolysis cell with a trickle bed column packed with a hydrophobic platinum catalyst. The column effects isotopic exchange between countercurrent streams of electrolytic hydrogen and liquid water while the electrolysis cell contributes to isotope separation by virtue of the kinetic isotope effect inherent in the hydrogen evolution reaction. The main features of the CECE process for heavy water production are presented as well as a discussion of the inherent positive synergistic effects, and other advantages and disadvantages of the process. Several potential applications of the process in the nuclear power industry are discussed. 3 figures, 2 tables

Kinematic separation and mass analysis of heavy recoiling nuclei

International Nuclear Information System (INIS)

Oganesyan, Yu.Ts.; Eremin, A.V.; Belozerov, A.V.

2002-01-01

Within the past twelve years, the recoil separator VASSILISSA has been used for investigation of evaporation residues produced in heavy-ion induced complete-fusion reactions. In the course of the experimental work in the region of the elements with 92 ≤ Z ≤ 94, fourteen new isotopes have been identified by the parent-daughter correlations. The study of the decay properties and formation cross sections of the isotopes of elements 110, 112, and 114 was performed with the use of the high intensity 48 Ca beams; 232 Th, 238 U and 242 Pu targets were used in the experiments. At the beam energies corresponding to the calculated cross-section maxima of the 3n evaporation channels, the isotopes 277 110, 283 112, and 287 114 were produced and identified. For further experiments aimed at the synthesis of the superheavy element isotopes (Z ≥ 110) with the intensive 48 Ca extracted beams, the improvements in the ion optical system of the separator and of the focal plane detector system have been made. As a result, for heavy recoiling nuclei with masses A ∼ 250, the mass resolution of about 2.5 % was achieved with a good energy and position resolutions of the focal plane detectors

Electrical and dielectric characteristics of Al/Dy{sub 2}O{sub 3}/p-Si heterostructure

Energy Technology Data Exchange (ETDEWEB)

Cherif, Ahlem, E-mail: ahlem_cherif@yahoo.fr [Université de Sousse, Ecole Supérieure des Sciences et de la Technologie, Inst Sup Inf Télécom, LabEM-LR11ES34 Energie et de Matériaux, 4011, Hammam Sousse (Tunisia); Jomni, Sami [Université de Tunis El Manar, Faculté des Sciences de Tunis, LR: LAB MA03 Matériaux, Organization et Propriétés, 2092 Tunis (Tunisia); Université de Sousse, Ecole Supérieure des Sciences et de la Technologie, 4011, Hammam Sousse (Tunisia); Mliki, Najeh [Université de Tunis El Manar, Faculté des Sciences de Tunis, LR: LAB MA03 Matériaux, Organization et Propriétés, 2092 Tunis (Tunisia); Beji, Lotfi [Université de Sousse, Ecole Supérieure des Sciences et de la Technologie, Inst Sup Inf Télécom, LabEM-LR11ES34 Energie et de Matériaux, 4011, Hammam Sousse (Tunisia)

2013-11-15

In this work we report the electrical characteristics of high-k Dy{sub 2}O{sub 3} dielectric deposited on p-Si substrate by electron beam deposition under ultra vacuum. The surface morphology of Dy{sub 2}O{sub 3} is investigated by scanning electron microscopy (SEM) and atomic force microscopy (AFM). The surface topography analysis reveals that the Dy{sub 2}O{sub 3} film is nanograined and contains numerous contacts between columnar grains. The electrical properties of Al/Dy{sub 2}O{sub 3}/p-Si heterostructure are further analyzed by current–voltage (I–V), capacitance–voltage (C–V), capacitance–frequency (C–f) and conductance–frequency (G–f) measurements. The dominant conduction mechanisms which governed the Al/Dy{sub 2}O{sub 3}/p-Si heterostrucure are determined. The hetrostructure induces a significant value of leakage current: 1.1×10{sup −5} A at flat-band voltage −1 V which is linked to the structural properties of the elaborated structure. The effects of grain boundaries and oxygen vacancies within the dielectric are observed in term of leakage current. Indeed, the C(V) characteristics measured at different applied voltage show a large frequency–dispersion, indicative of the presence of a continuous distribution of interface states. So, the interface state densities are determined from the C(V) characteristics to be around 10{sup 13} eV{sup −1} cm{sup −2}. C(f) measurements elucidate that the capacitance behavior is typical of material with traps. From G(f) and C(f) measurement the trap density and relaxation time are also determined. It is suggested that the interface states series resistance are important parameters that strongly influence the electrical properties of Al/Dy{sub 2}O{sub 3}/p-Si heterostrucure.

Feeding times of high spin states in sup(152,154)Dy: Probes of nuclear structure above the yrast line

International Nuclear Information System (INIS)

Azgui, F.; Emling, H.; Grosse, E.; Michel, C.; Simon, R.S.; Spreng, W.; Wollersheim, H.J.; Khoo, T.L.; Chowdhury, P.; Frekers, D.; Janssens, R.V.F.; Pakkanen, A.; Daly, P.J.; Kortelahti, M.; Schwalm, D.; Seiler-Clark, G.

1985-01-01

Measurements of feeding times of high spin yrast states up to spin 30 (h/2π) in 154 Dy and 36 (h/2π) in 152 Dy were utilized to obtain information about possible spin dependent shape changes. The reactions 25 Mg ( 134 Xe, 5n), 124 Sn ( 34 S, 4n) and 25 Mg ( 132 Xe, 5n), 122 Sn ( 34 S, 4n) were used to populate the high spin states in 154 Dy and 152 Dy, respectively. Feeding times as well as lifetimes were determined with the recoil distance technique. In 152 Dy only long feeding times (>=10 ps) could be identified, indicating that the aligned-particle yrast states are fed through configurations of similar character, with little direct population from collective cascades in the continuum region. In 154 Dy discrete states with I<=30 (h/2π) have lifetimes which are characteristically collective, whereas the preyrast cascades exhibit both fast (< or approx.1 ps) and slow (proportional10 ps) feeding components. The latter imply a change with increasing spin from collective to aligned-particle character, probably associated with a prolate to oblate shape transition. (orig.)

Defining a stable water isotope framework for isotope hydrology application in a large trans-boundary watershed (Russian Federation/Ukraine).

Science.gov (United States)

Vystavna, Yuliya; Diadin, Dmytro; Huneau, Frédéric

2018-05-01

Stable isotopes of hydrogen ( 2 H) and oxygen ( 18 O) of the water molecule were used to assess the relationship between precipitation, surface water and groundwater in a large Russia/Ukraine trans-boundary river basin. Precipitation was sampled from November 2013 to February 2015, and surface water and groundwater were sampled during high and low flow in 2014. A local meteoric water line was defined for the Ukrainian part of the basin. The isotopic seasonality in precipitation was evident with depletion in heavy isotopes in November-March and an enrichment in April-October, indicating continental and temperature effects. Surface water was enriched in stable water isotopes from upstream to downstream sites due to progressive evaporation. Stable water isotopes in groundwater indicated that recharge occurs mainly during winter and spring. A one-year data set is probably not sufficient to report the seasonality of groundwater recharge, but this survey can be used to identify the stable water isotopes framework in a weakly gauged basin for further hydrological and geochemical studies.

Facile synthesis, structural characterization, and photoluminescence mechanism of Dy{sup 3+} doped YVO{sub 4} and Ca{sup 2+} co-doped YVO{sub 4}:Dy{sup 3+} nano-lattices

Energy Technology Data Exchange (ETDEWEB)

Dhiren Meetei, Sanoujam, E-mail: sdmdhiren@gmail.com; Dorendrajit Singh, Shougaijam, E-mail: dorendrajit@yahoo.co.in, E-mail: mdebensingh@gmail.com [Department of Physics, Manipur University, Canchipur, Imphal-795003, Manipur (India); Deben Singh, Mutum, E-mail: dorendrajit@yahoo.co.in, E-mail: mdebensingh@gmail.com [Department of Physics, Thambal Marik College, Oinam-795134, Bishnupur, Manipur (India)

2014-05-28

Light plays a vital role in the evolution of life. From sunlight to candle-light and then to other form of lighting devices, human beings are utilizing light since time immemorial. Lighting devices such as conventional incandescent lamp and fluorescent lamp have been replaced by Light Emitting Diodes (LEDs) for the later is cheap, durable, etc. Now-a-days, phosphor converted LEDs have been burning issues in the fabrication of lighting devices. Especially, lanthanide ion(s) doped phosphors are of great interest for the same. However, doped phosphors have a limitation of luminescence quenching, i.e., instead of increasing luminescence on increasing dopant concentration, the luminescence decreases. Therefore, it must be rectified by one or other means so as to get maximum desirable intensity for uses in display or lighting devices. In the present work, YVO{sub 4}:Dy{sup 3+} and YVO{sub 4}:Dy{sup 3+}/Ca{sup 2+} nano-lattices are synthesized by a facile technique. Structural characterizations such as x-ray diffraction, SEM, TEM, HRTEM, and Selected Area Electron Diffraction (SAED) of the samples are reported. Photoluminescence (PL) excitation and emission, enhanced mechanism, and lifetime are thoroughly discussed. PL intensity of the quenched YVO{sub 4}:Dy{sup 3+} is made increased up to 432.63% by Ca{sup 2+} co-doping. Role of the Ca{sup 2+} on the luminescence enhanced mechanism of YVO{sub 4}:Dy{sup 3+}/Ca{sup 2+} is elucidated.

Influence of ageing treatment on microstructure, mechanical and bio-corrosion properties of Mg-Dy alloys.

Science.gov (United States)

Yang, Lei; Huang, Yuanding; Feyerabend, Frank; Willumeit, Regine; Kainer, Karl Ulrich; Hort, Norbert

2012-09-01

Mg-Dy alloys have shown to be promising for medical applications. In order to investigate the influence of ageing treatment on their mechanical and corrosion properties, three Mg-xDy alloys (x=10, 15, 20 wt%) were prepared. Their microstructure, mechanical and corrosion behavior were investigated. The results indicate that ageing at 250 °C has little influence on the mechanical and corrosion properties. In contrast, ageing at 200 °C significantly increases the yield strength, and reduces the ductility. After ageing at 200 °C, the corrosion rate of Mg-20Dy alloy increases largely in 0.9 wt% NaCl solution, but remains unchanged in cell culture medium. Copyright © 2012 Elsevier Ltd. All rights reserved.

Phototransferred TL studies in CaSO4:Dy

International Nuclear Information System (INIS)

Nagpal, J.S.; Kathuria, V.K.; Gangadharan, P.

1980-01-01

PTTL studies in CaSO 4 :Dy have revealed two high temperature peaks at 500 and 570 0 C in γ-exposed phosphor. Employing 365 nm for phototransfer at elevated temperature 95 0 C, PTTL can serve a useful technique for re-estimation of the radiation exposure. (author)

Antiferroquadrupolar ordering and anisotropic magnetic phase diagram of dysprosium palladium bronze, DyPd3S4

International Nuclear Information System (INIS)

Matsuoka, Eiichi; Tayama, Takashi; Sakakibara, Toshiro; Hiroi, Zenji; Takeda, Naoya; Ishikawa, Masayasu; Shirakawa, Naoki

2007-01-01

From the measurements of magnetization and specific heat, we constructed B-T phase diagrams of single-crystalline DyPd 3 S 4 which is known to exhibit antiferroquadrupolar (AFQ) and antiferromagnetic (AFM) ordering at low temperatures. The phase diagrams are found to be highly anisotropic and re-entrant, which are typical of rare-earth compounds exhibiting multipolar ordering. The crystalline electric field (CEF) scheme of Dy 3+ in DyPd 3S4 was deduced from the specific heat and magnetization measurements of the Y-diluted compounds Dy 1-x Y x Pd 3 S 4 (0.1≤x≤0.9) and discussed in detail. The CEF ground state was determined to be the orbitally-degenerated quartet Γ 67 (1) , and the overall splitting width was estimated to be about 104 K. No correlation was found between the anisotropy of T Q and that of the Zeeman splitting width of the ground quartet Γ 67 (1) . (author)

Element distribution in the corrosion layer and cytotoxicity of alloy Mg-10Dy during in vitro biodegradation.

Science.gov (United States)

Yang, Lei; Hort, Norbert; Laipple, Daniel; Höche, Daniel; Huang, Yuanding; Kainer, Karl Ulrich; Willumeit, Regine; Feyerabend, Frank

2013-11-01

The present work investigates the corrosion behaviour, the element distribution in the corrosion layer and the cytocompatibility of alloy Mg-10Dy. The corrosion experiments were performed in a cell culture medium (CCM) under cell culture conditions close to the in vivo environment. The element distribution on the surface as well as in cross-sections of the corrosion layer was investigated using scanning electron microscopy, energy-dispersive X-ray analysis, X-ray photoelectron spectroscopy and X-ray diffraction. The cytocompatibility of alloy Mg-10Dy with primary human osteoblasts was evaluated by MTT, cell adhesion and live/dead staining tests. The results show that the corrosion layer was enriched in Dy, while the P and Ca content gradually decreased from the surface to the bottom of the corrosion layer. In addition, large amounts of MgCO3·3H2O formed in the corrosion layer after 28 days immersion. Both extracts and the Dy-enriched corrosion layer of alloy Mg-10Dy showed no cytotoxicity to primary human osteoblasts. Copyright © 2012 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Tunable photoluminescence and magnetic properties of Dy(3+) and Eu(3+) doped GdVO4 multifunctional phosphors.

Science.gov (United States)

Liu, Yanxia; Liu, Guixia; Dong, Xiangting; Wang, Jinxian; Yu, Wensheng

2015-10-28

A series of Dy(3+) or/and Eu(3+) doped GdVO4 phosphors were successfully prepared by a simple hydrothermal method and characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), energy-dispersive X-ray spectrometry (EDS), photoluminescence (PL) spectroscopy and vibrating sample magnetometry (VSM). The results indicate that the as-prepared samples are pure tetragonal phase GdVO4, taking on nanoparticles with an average size of 45 nm. Under ultraviolet (UV) light excitation, the individual Dy(3+) or Eu(3+) ion activated GdVO4 phosphors exhibit excellent emission properties in their respective regions. The mechanism of energy transfer from the VO4(3-) group and the charge transfer band (CTB) to Dy(3+) and Eu(3+) ions is proposed. Color-tunable emissions in GdVO4:Dy(3+),Eu(3+) phosphors are realized through adopting different excitation wavelengths or adjusting the appropriate concentration of Dy(3+) and Eu(3+) when excited by a single excitation wavelength. In addition, the as-prepared samples show paramagnetic properties at room temperature. This kind of multifunctional color-tunable phosphor has great potential applications in the fields of photoelectronic devices and biomedical sciences.

Synthesis of novel Dy3+ activated phosphate phosphors for NUV excited LED

International Nuclear Information System (INIS)

Shinde, K.N.; Dhoble, S.J.; Kumar, Animesh

2011-01-01

The new trivalent dysprosium activated X 6 AlP 5 O 20 (where X=Sr, Ba, Ca and Mg) phosphors were prepared by the combustion method. The prepared phosphors are characterized by XRD, photoluminescence and SEM techniques. Excited by 350 nm near-ultraviolet (NUV) light, the phosphors show an efficient blue and yellow band emissions, which originates from the 4 F 9/2 → 6 H 15/2 and 4 F 9/2 → 6 H 13/2 transitions of Dy 3+ ion, respectively. The excitation spectra of the phosphors are broadband extending from 340 to 400 nm, which are characteristics of NUV excited LED. The effect of the Dy 3+ concentration on the luminescence properties of X 6 AlP 5 O 20 :Dy 3+ (where X=Sr, Ba, Ca and Mg) phosphors is studied. Ca 6 AlP 5 O 20 phosphors show strong PL emission intensity around 25 times more as compared to Ba 6 AlP 5 O 20 , Sr 6 AlP 5 O 20 and Mg 6 AlP 5 O 20 phosphors. The investigated prepared phosphors are suitable for a NUV excited LED. - Research highlights: → Novel Dy 3+ activated X 6 AlP 5 O 20 (where X=Sr,Ba,Ca and Mg) phosphors were prepared by combustion method which is very low cost and time saving synthesis method. → The excitation spectra of the phosphors are broad band extending from 340 nm to 400 nm, which is characteristics of NUV excited LED. → PL emission spectra show two emissions (485 and 573 nm) and X 6 AlP 5 O 20 :Dy 3+ 0.5 mol% (where X=Sr,Ba,Ca and Mg) phosphors shows strongest PL emission intensity. → SEM analysis indicates that phosphor particles have irregular shape, porous morphology and less than 3-4 μm in size, which is suitable for the solid state lighting (coating purpose).

The study of antibacterial activity and stability of dyed cotton fabrics modified with different forms of silver

Directory of Open Access Journals (Sweden)

Lazić Vesna

2012-01-01

Full Text Available This study compares the effect of colloidal silver nanoparticles and commercial RUCO-BAC AGP agent with silver chloride as an active component on antibacterial activity of dyed cotton fabrics. Cotton fabrics were dyed with vat dyes Bezanthren olive T and Bezanthren grey FFB. Antibacterial activity of silver loaded dyed cotton fabrics was tested against Gram-positive bacterium Staphylococcus aureus and Gram-negative bacterium Escherichia coli. Unlike RUCO-BAC AGP synthesized silver nanoparticles deposited onto dyed cotton fabrics provided maximum bacteria reduction independently of applied dye. The stability of modified cotton fabrics was analyzed in artificial sweat at pH 5.5 and 8.0. Approximately the same amount of silver was released from differently modified cotton fabrics in artificial sweat. Larger amount of silver was released in the sweat at pH 8.0.

1000 tones of heavy water produced at ROMAG PROD, Drobeta-Turnu Severin

International Nuclear Information System (INIS)

2001-01-01

On May 25, 2001 the heavy water plant ROMAG PROD at Drobeta-Turnu Severin recorded the production of the 1000-th tone of nuclear purity heavy water. The heavy water plant ROMAG PROD makes use of a technology based on the results of isotopic deuterium separation research carried out at the Research and Design Institutes of Cluj, Craiova, Pitesti and Ploiesti during 1957-1970 and the separation technology tested at Ramnicu-Valcea pilot plant (at present the Cryogenics and Isotope Separation Institute). The first investments at ROMAG PROD were made in 1979 and on July 17, 1988 was produced the first amount of heavy water at the required parameters for CANDU type nuclear reactors. The period between 1990-1992 was dedicated to the project completion, upgrading the technological facilities and retrofitting the environmental protection and monitoring systems. Production was resumed in 1992. The first 500 t of heavy water required for the Cernavoda NPP first reactor operation were produced by summer 1997. The additional amount of 500 t of heavy water was produced between 1997-2001. ROMAG PROD obtained the ISO 9001/2001 certificate for the quality management system, the ISO 14001/1997 certificate for the environmental management system and the new environmental permit

Table of specific activities of selected isotopes

International Nuclear Information System (INIS)

Shipley, G.

The bulk of this publication consists of a table of the half-lives, decay modes, and specific activities of isotopes selected for their particular interest to the Environmental Health and Safety Department, LBL. The specific activities were calculated with a PDP 9/15 computer. Also included in the report is a table of stable isotopes, the Th and U decay chains, a chart of the nuclides for elements 101 through 106, the heavy element region of the periodic table, and a specific activity monograph. 5 figures, 2 tables

Giant magnetocaloric effect in antiferromagnetic DyVO{sub 4} compound

Energy Technology Data Exchange (ETDEWEB)

Midya, A., E-mail: arindam.midya@saha.ac.in; Khan, N.; Bhoi, D.; Mandal, P.

2014-09-01

We have investigated the magnetic and magnetocaloric properties of DyVO{sub 4} by magnetization and heat capacity measurements. χ(T) shows antiferromagnetic to paramagnetic transition at T{sub N}{sup Dy}∼3.5K. The compound undergoes a metamagnetic transition and exhibits a huge entropy change. The maximum values of magnetic entropy change (ΔS{sub M}), adiabatic temperature change (ΔT{sub ad}) and refrigerant capacity (RC) reach 26 J kg{sup −1} K{sup −1}, 17 K, and 526 J kg{sup −1}, respectively for a field change of 0–8 T. Moreover, the material is highly insulating and exhibits no thermal and field hysteresis, satisfying the necessary conditions for a good magnetic refrigerant material.

Research for magnetocaloric effect of Gd{sub 1-x}Dy{sub x} alloy

Energy Technology Data Exchange (ETDEWEB)

Hou, Xueling; Shitao, Li; An, Zhang; Hui, Xu; Ni, Jiansen; Zhou, Bangxin [Institute of Materials, Shanghai University, Shanghai 20007 (China)

2007-12-15

The magnetocaloric effect (MEC) in Gd{sub 1-x}Dy{sub x} (x=0.13,0.20,0.27,0.34,0.40) alloys is investigated using commercial elements with purity of up to 99.80% for Gd and Dy. These alloys are prepared by arc melting in stoichiometric proportions on a water-cooled copper crucible under high pure argon atmosphere. As a result, when x was changed from 0 to 40at%, the adiabatic temperature change ({delta}T) increases from 1.6 K to 3.1 K, the Curie temperature decreased from 288 K to 245.5 K. Gd{sub 73}Dy{sub 27} exhibits the largest {delta}T{sub max} value of 3.1 K at the T{sub C} value of 260 K among the alloys investigated up to 1.2 T (tesla) applied field, it is almost same as the {delta}T of high pure unitary Gd (99.99%) and is clearly superior to commercial unitary Gd (99.80%). The T{sub C} of Gd{sub 73}Dy{sub 27} alloy is minor to high pure unitary Gd (99.99%) and commercially unitary Gd (99.80%). But this alloy prepared by commercial elements with low cost has better MEC to be a promising candidate for magnetic working substances for room temperature magnetic refrigeration. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

Strategie řízení třídy u studentů učitelství na praxi

OpenAIRE

Lojdová Kateřina; Škarková Lucie; Lukas Josef

2016-01-01

Cílem výzkumu je popsat strategie řízení třídy u studentů učitelství na praxi na druhém stupni českých základních škol. Právě řízení třídy je pro studenty učitelství na praxi obtížné. Nezvládnutí práce se třídou může vést až ke změně kariérní dráhy. Výzkum hloubkově interpretuje strategie řízení třídy u studentů učitelství na praxi a popisuje některé problémy, se kterými se studenti učitelství potýkají. Skrze strategie řízení třídy učitel ovlivňuje fyzický a sociální prostor školní třídy za ú...

Size dependences of crystal structure and magnetic properties of DyMnO{sub 3} nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Tajiri, T., E-mail: tajiri@fukuoka-u.ac.jp [Faculty of Science, Fukuoka University, Fukuoka 814-0180 (Japan); Terashita, N.; Hamamoto, K.; Deguchi, H.; Mito, M. [Faculty of Engineering, Kyushu Institute of Technology, Kitakyushu 804-8550 (Japan); Morimoto, Y.; Konishi, K. [Graduate School of Science and Engineering, Ehime University, Matsuyama 790-8577 (Japan); Kohno, A. [Faculty of Science, Fukuoka University, Fukuoka 814-0180 (Japan)

2013-11-15

We synthesized DyMnO{sub 3} nanoparticles with particle sizes of about 7.5–15.3 nm in the pores of mesoporous silica and investigated their crystal structure and magnetic properties. As the particle size decreased, the lattice constants of the DyMnO{sub 3} nanoparticles deviated from those of the bulk crystal, and the Jahn–Teller distortion in the nanoparticle systems decreased. In addition, the estimated lattice strain increased with decreasing particle size. The DyMnO{sub 3} nanoparticles showed superparamagnetic behavior. The blocking temperature and the coercive field increased with decreasing particle size, and this behavior was contrary to the usual magnetic size effects. It is deduced that these unique size dependences of the magnetic properties for the DyMnO{sub 3} nanoparticles were derived from the changes in lattice constants and lattice strain. The anisotropic lattice deformation in the crystal structure of the nanoparticles induces an enhancement of the magnetic anisotropy, which results in the increase in blocking temperature and coercive field with decreasing particle size. - Highlights: • We successfully synthesized DyMnO{sub 3} nanoparticles with particle size of 7.5–15.3 nm. • Lattice strain increases with decreasing particle size. • Lattice constants exhibit anisotropic change with decreasing particle size. • Distortion of crystal structure leads to enhancement of magnetic anisotropy constant. • Blocking temperature and coercive field increases with decreasing particle size.

Peculiarity of component interaction in {l_brace}Y, Dy{r_brace}-Mn-Sn ternary systems

Energy Technology Data Exchange (ETDEWEB)

Romaka, V.V. [Department of Materials Engineering and Applied Physics, Lviv Polytechnic National University, Ustyyanovycha Str. 5, 79013 Lviv (Ukraine); Konyk, M. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Romaka, L., E-mail: romakal@franko.lviv.ua [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Pavlyuk, V. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine); Jan Dlugosz University, Institute of Chemistry, Environmental Protection and Biotechnology, al. Armii Krajowej 13/15, 42200 Czestochowa (Poland); Ehrenberg, H. [Institute for Complex Materials, IFW Dresden, Helmholtzstrasse 20, D-01069 Dresden (Germany); Tkachuk, A. [Inorganic Chemistry Department, Ivan Franko Lviv National University, Kyryla and Mefodiya Str. 6, 79005 Lviv (Ukraine)

2011-07-14

Highlights: > {l_brace}Y, Dy{r_brace}-Mn-Sn ternary systems at 770 K are characterized by formation of stannides with general compositions RMn{sub 6}Sn{sub 6} and R{sub 4}Mn{sub 4}Sn{sub 7}. > The crystal structure of YMn{sub 6}Sn{sub 6} was determined by single crystal and powder diffraction methods. > Structural analysis showed that Dy{sub 4}Mn{sub 4}Sn{sub 7} compound is disordered. > Isostructural R{sub 4}Mn{sub 4}Sn{sub 7} compounds were also found with Gd, Tb, Ho, Er, Tm(confirmed), Yb, and Lu. - Abstract: The phase equilibria in the Y-Mn-Sn and Dy-Mn-Sn ternary systems were studied at 770 K by means of X-ray and metallographic analyses in the whole concentration range. Both Y-Mn-Sn and Dy-Mn-Sn systems are characterized by formation of two ternary compounds RMn{sub 6}Sn{sub 6} (MgFe{sub 6}Ge{sub 6}-type, space group P6/mmm) and R{sub 4}Mn{sub 4}Sn{sub 7} (Zr{sub 4}Co{sub 4}Ge{sub 7}-type, space group I4/mmm). The disorder in Dy{sub 4}Mn{sub 4}Sn{sub 7} compound was found by single crystal method. Compounds with the same type of structure were also found with Gd, Tb, Ho, Er, Tm (confirmed), Yb, and Lu and their lattice parameters were determined.

Labeling of biotin with 166Dy/166Ho as a stable in vivo generator system

International Nuclear Information System (INIS)

Ferro-Flores, G.; Monroy-Guzman, F.; Tendilla, J.I.; Garcia-Salinas, L.; Villarreal-Barajas, J.E.; Arteaga-Murphy, C.

2002-01-01

Biotin (cis-tetrahydro-2-oxothieno[3,4-d]imidazoline-4-valeric acid) is a 244 Da vitamin found in low concentration in blood and tissue (vitamin H). The aim of this work was to synthesize 166 Dy/ 166 Ho-DTPA-bisBiotin to evaluate its potential as a new radiopharmaceutical for targeted radiotherapy. Dysprosium-166/ holmium-166 chloride was obtained by neutron irradiation of 20 mg of enriched Dy 2 O 3 ( 164 Dy, 99 %, from Oak Ridge NL) in a Triga Mark III reactor at a flux in the central thimble of 3.10 13 n. cm -2 s -1 for 20 h. Following irradiation, the target was allowed to decay for 2 days, then 100 μL of 12 N chloride acid were added and stirred for 1 min. To this solution was added 500 μL of injectable water and the whole was also stirred for 2 min. The average radioactive concentration was 332 MBq/ml. The biotin used in this investigation was covalently conjugated to diethylenetriamine pentaacetic acid (DTPA) through the use of the cyclic anhydride and lysine conjugate to biotin (biocytin) to produce DTPA-α,ω-bis(biocytin amide)(DTPA-bisBiotin). Sterile and apyrogenic V-vial was prepared to contain 2.0 mg (1.9 x 10 -3 mmol) of the DTPA-bisbiotin compound in 1.0 ml of 0.05 M bicarbonate buffer (pH 8.0) and then 20 μL of 166 Dy2Cl3 solution were added to the preparation. Thin Layer Chromatography aluminum cellulose sheets were utilised as the stationary phase and a ternary mixture of methanol:water:ammonium hydroxide (20:40:2) as the mobile phase. 166 Dy/ 166 Ho-DTPA-bisBiotin travelled with the solvent front R f 0.9-1.0 and the Dy +3 /Ho +3 species remained at the origin (R f = 0). The biological integrity of labelled biotin was achieved evaluating its avidity for avidin in an agarose column. Stability studies against dilution were carried out by diluting the radiocomplex solution with saline and with human serum at 310 K. After 10 min and 24 h the radiochemical purity of each 166 Dy/ 166 Ho complex solution was determined by TLC. The complex 166 Dy/ 166

Ultrahigh coercivity and core-shell microstructure achieved in oriented Nd-Fe-B thin films diffusion-processed with Dy-based alloys

Energy Technology Data Exchange (ETDEWEB)

Zhang, Tongbo; Zhou, Xiaoqian; Yu, Dedong; Fu, Yanqing; Cui, Weibin [Northeastern University, Key Laboratory of Electromagnetic Processing of Materials (EPM), Ministry of Education, Shenyang (China); Northeastern University, Department of Physics and Chemistry of Materials, School of Materials Science and Engineering, Shenyang (China); Li, Guojian; Wang, Qiang [Northeastern University, Key Laboratory of Electromagnetic Processing of Materials (EPM), Ministry of Education, Shenyang (China)

2017-01-15

Ultrahigh ambient coercivities of ∝4 T were achieved in Nd-Fe-B benchmark thin film with coercivity of 1.06 T by diffusion-processing with Dy, Dy{sub 70}Cu{sub 30} and Dy{sub 80}Ag{sub 20} alloy layer. High texture and good squareness were obtained. In triple-junction regions, Dy element was found to be immiscible with Nd element. Microstructure observation indicated the typical gradient elementary distribution. Unambiguous core/shell microstructure was characterized by transition electron microscopy. Due to the enhanced ambient coercivity, the coercivity temperature stability was also substantially increased. (orig.)

New isotopes of elements 104, 106 and 108 - highly stable superheavy nuclei

International Nuclear Information System (INIS)

Oganessian, Yuri

1994-01-01

In April 1993, as part of a joint Dubna-Livermore experiment at the Flerov Laboratory of Nuclear Reactions, new heavy isotopes of elements 104 and 106 were synthesized - 262 104, 265 106 and 266 106. Compared with the known even-even isotopes of elements 104 and 106, the new nuclei are characterized by their extraordinary high resistance to spontaneous fission. This is a direct proof of the macro-microscopic theory predictions in its version calculated by A.Sobiczewski et al. regarding a substantial increase in the half-lives of heavy nuclei near deformed shells with atomic number (Z) 108 and neutron number (N) 162.

Anisotropy of the magnetocaloric effect in DyNiAl

Czech Academy of Sciences Publication Activity Database

Kaštil, J.; Javorský, P.; Andreev, Alexander V.

2009-01-01

Roč. 321, č. 15 (2009), s. 2318-2321 ISSN 0304-8853 Institutional research plan: CEZ:AV0Z10100520 Keywords : magnetocaloric effec * DyNiAl * magnetism * anisotropy Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.204, year: 2009

Solvent directed morphologies and enhanced luminescent properties of BaWO4:Tm3+,Dy3+ for white light emitting diodes

Science.gov (United States)

Wu, Hongyue; Yang, Junfeng; Wang, Xiaoxue; Gan, Shucai; Li, Linlin

2018-05-01

A series of Tm3+ and Dy3+ codoped BaWO4 phosphors with tunable shapes were controllably synthesized by a facile solvothermal method. The effects of ratio of ethylene glycol (EG) and water on the morphologies of BaWO4 structures are systematically studied. It was discovered that the reason for these morphological changes is based on the reaction speed of the kinetic control, which relates to the strong chelating abilities of ethylene glycol. And when the solvent is pure ethylene glycol, the peanut-like BaWO4:Dy3+ has the strongest emission intensity. Moreover, the emission color of the phosphors varied from blue (0.232, 0.180) to white (0.268, 0.250) by controlling Dy3+ ions content with a fixed Tm3+ concentration. The energy transfer mechanism was investigated in detail. With increasing the doped concentration of Dy3+ ions, the energy transfer efficiency of BaWO4:0.005Tm3+,yDy3+ increased gradually and reached as high as 63% when the Dy3+ doped concentration is 0.03. The critical distance RC calculated by the spectral overlap method is about 19.93 Å, and it is in good agreement with that obtained using the concentration quenching method (19.70 Å), indicating that the electric dipole-dipole interaction is the main energy transfer mechanism for BaWO4:Tm3+,Dy3+ phosphors.

Field-induced non-collinear magnetic structures in amorphous Co80-xDy xB20 alloys

International Nuclear Information System (INIS)

Annouar, F.; Roky, K.; Lassri, H.; Elmoussaoui, A.; Driouch, L.; Ayadi, M.; Omri, M.; Krishnan, R.

2005-01-01

Amorphous Co 80-x Dy x B 20 alloys have been prepared by melt spinning technique and their magnetic properties have been studied. The mean field theory has been used to explain the temperature dependence of the magnetization. High-field magnetization studies performed at 4.2 K in magnetic fields up to 38 T have revealed, for samples with stoichiometry close to that of a compensated ferrimagnet, a magnetic behavior that is characteristic of a non-collinear magnetic structure of the Dy and Co sublattices. From the non-collinear regime the exchange interactions between the Co and Dy magnetic sublattices and the magnetic anisotropy constants have been evaluated

Isotopic Resonance Hypothesis: Experimental Verification by Escherichia coli Growth Measurements

Science.gov (United States)

Xie, Xueshu; Zubarev, Roman A.

2015-03-01

Isotopic composition of reactants affects the rates of chemical and biochemical reactions. As a rule, enrichment of heavy stable isotopes leads to progressively slower reactions. But the recent isotopic resonance hypothesis suggests that the dependence of the reaction rate upon the enrichment degree is not monotonous. Instead, at some ``resonance'' isotopic compositions, the kinetics increases, while at ``off-resonance'' compositions the same reactions progress slower. To test the predictions of this hypothesis for the elements C, H, N and O, we designed a precise (standard error +/-0.05%) experiment that measures the parameters of bacterial growth in minimal media with varying isotopic composition. A number of predicted resonance conditions were tested, with significant enhancements in kinetics discovered at these conditions. The combined statistics extremely strongly supports the validity of the isotopic resonance phenomenon (p biotechnology, medicine, chemistry and other areas.

Hydrogen isotope separation by cryogenic distillation method

International Nuclear Information System (INIS)

Hayakawa, Nobuo; Mitsui, Jin

1987-01-01

Hydrogen isotope separation in fusion fuel cycle and tritium recovery from heavy water reactor are very important, and therefore the early establishment of these separation techniques are desired. The cryogenic distillation method in particular is promising for the separation of hydrogen isotope and the recovery of high concentrated tritium. The studies of hydrogen isotope separation by cryogenic distillation method have been carried out by using the experimental apparatus made for the first time in Japan. The separation of three components (H 2 -HD-D 2 ) under total reflux conditions was got by using the packing tower of 500 mm height. It was confirmed that the Height Equivalent Theoretical Plate (HETP) was 20 - 30 mm for the vapor's line velocity of 20 - 80 mm/s. (author)

Weathering and vegetation controls on nickel isotope fractionation in surface ultramafic environments (Albania)

Science.gov (United States)

Estrade, Nicolas; Cloquet, Christophe; Echevarria, Guillaume; Sterckeman, Thibault; Deng, Tenghaobo; Tang, YeTao; Morel, Jean-Louis

2015-08-01

The dissolved nickel (Ni) isotopic composition of rivers and oceans presents an apparent paradox. Even though rivers represent a major source of Ni in the oceans, seawater is more enriched in the heavier isotopes than river-water. Additional sources or processes must therefore be invoked to account for the isotopic budget of dissolved Ni in seawater. Weathering of continental rocks is thought to play a major role in determining the magnitude and sign of isotopic fractionation of metals between a rock and the dissolved product. We present a study of Ni isotopes in the rock-soil-plant systems of several ultramafic environments. The results reveal key insights into the magnitude and the control of isotopic fractionation during the weathering of continental ultramafic rocks. This study introduces new constraints on the influence of vegetation during the weathering process, which should be taken into account in interpretations of the variability of Ni isotopes in rivers. The study area is located in a temperate climate zone within the ophiolitic belt area of Albania. The serpentinized peridotites sampled present a narrow range of heavy Ni isotopic compositions (δ60Ni = 0.25 ± 0.16 ‰, 2SD n = 2). At two locations, horizons within two soil profiles affected by different degrees of weathering all presented light isotopic compositions compared to the parent rock (Δ60Nisoil-rock up to - 0.63 ‰). This suggests that the soil pool takes up the light isotopes, while the heavier isotopes remain in the dissolved phase. By combining elemental and mineralogical analyses with the isotope compositions determined for the soils, the extent of fractionation was found to be controlled by the secondary minerals formed in the soil. The types of vegetation growing on ultramafic-derived soils are highly adapted and include both Ni-hyperaccumulating species, which can accumulate several percent per weight of Ni, and non-accumulating species. Whole-plant isotopic compositions were found

Influence of annealing temperature on the Dy diffusion process in NdFeB magnets

Energy Technology Data Exchange (ETDEWEB)

Hu, Sheng-qing, E-mail: joy_hsq@126.com [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); Peng, Kun, E-mail: kpeng@hnu.edu.cn [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China); College of Materials Science and Engineering, Hunan University, Changsha 410082 (China); Chen, Hong [State Key Laboratory of Powder Metallurgy, Central South University, Changsha 410083 (China)

2017-03-15

Sintered NdFeB magnets were coated with a layer of Dy metal using electron beam evaporation method and then annealed at various temperatures to investigate the temperature dependence of Dy diffusion process in NdFeB magnets. A Dy-rich phase was observed along the grain boundaries after the grain boundary diffusion process, the diffusion coefficients of various temperatures were obtained, the diffusion coefficients of Dy along the grain boundaries at 800 °C and 900 °C were determined to be 9.8×10{sup −8} cm{sup 2} s{sup −1} and 2.4×10{sup −7} cm{sup 2} s{sup −1}, respectively. The diffusion length depended on the annealing temperature and the maximum diffusion length of approximately 1.8 mm and 3.0 mm can be obtained after annealing at 800 °C and 900 °C for 8 h. Higher diffusion temperature results in the diffusion not only along the grain boundaries but also into grains and then decrease in magnetic properties. The optimum annealing conditions can be determined as 900 °C for 8 h. The coercivity was improved from 1040 kA/m to 1450 kA/m and its magnetization has no significant reduction after the grain boundary diffusion process at the optimum annealing conditions. - Highlights: • The optimum annealing conditions can be determined as 900 °C for 8 h. • The diffusion coefficient of Dy at 900 °Care determined to be 2.4×10{sup −7} cm{sup 2} s{sup −1}. • A maximum diffusion length of about 3 mm can be obtained.

Complex magnetic properties and large magnetocaloric effects in RCoGe (R=Tb, Dy compounds

Directory of Open Access Journals (Sweden)

Yan Zhang

2018-05-01

Full Text Available Complicated magnetic phase transitions and Large magnetocaloric effects (MCEs in RCoGe (R=Tb, Dy compounds have been reported in this paper. Results show that the TbCoGe compounds have a magnetic phase transition from antiferromagnetic to paramagnetic (AFM-PM at TN∼16 K, which is close to the value reported by neutron diffraction. The DyCoGe compound undergoes complicated phase changes from 2 K up to 300 K. The peak at 10 K displays a phase transition from antiferromagnetic to ferromagnetic (AFM-FM. In particular, a significant ferromagnetic to paramagnetic (FM-PM phase transition was found at the temperature as high as 175 K and the cusp becomes more abrupt with the magnetic field increasing from 0.01 T to 0.1 T. The maximum value of magnetic entropy change of TbCoGe and DyCoGe compounds achieve 14.5 J/kg K and 11.5 J/kg K respectively for a field change of 0-5 T. Additionally, the correspondingly considerable refrigerant capacity value of 260 J/kg and 242 J/kg are also obtained respectively, suggesting that both TbCoGe and DyCoGe compounds could be considered as good candidates for low temperature magnetic refrigerant.

Influence of annealing temperature on the Dy diffusion process in NdFeB magnets

Science.gov (United States)

Hu, Sheng-qing; Peng, Kun; Chen, Hong

2017-03-01

Sintered NdFeB magnets were coated with a layer of Dy metal using electron beam evaporation method and then annealed at various temperatures to investigate the temperature dependence of Dy diffusion process in NdFeB magnets. A Dy-rich phase was observed along the grain boundaries after the grain boundary diffusion process, the diffusion coefficients of various temperatures were obtained, the diffusion coefficients of Dy along the grain boundaries at 800 °C and 900 °C were determined to be 9.8×10-8 cm2 s-1 and 2.4×10-7 cm2 s-1, respectively. The diffusion length depended on the annealing temperature and the maximum diffusion length of approximately 1.8 mm and 3.0 mm can be obtained after annealing at 800 °C and 900 °C for 8 h. Higher diffusion temperature results in the diffusion not only along the grain boundaries but also into grains and then decrease in magnetic properties. The optimum annealing conditions can be determined as 900 °C for 8 h. The coercivity was improved from 1040 kA/m to 1450 kA/m and its magnetization has no significant reduction after the grain boundary diffusion process at the optimum annealing conditions.

Observation of room temperature saturated ferroelectric polarization in Dy substituted BiFeO3 ceramics

KAUST Repository

Zhang, Shuxia

2012-04-06

High quality Bi1− x Dy x FeO3 (0 ≤ x ≤ 0.15) ceramics have been fabricated by sintering Dy-doped BiFeO3 (BFO) precursor powders at a low temperature of 780 °C. The magnetic properties of BFO were improved by the introduction of Dy on the Bi-site. More importantly, well saturated ferroelectric hysteresis loops and polarization switching currents have been observed at room temperature. A large remnant polarization (2P r) value of 62 μC/cm2 is achieved, which is the highest value reported so far for rare-earth-doped BFO ceramics. Moreover, mechanisms for improved multiferroic properties depending on chemical doping-caused structure evolutions have also been discussed.

Observation of room temperature saturated ferroelectric polarization in Dy substituted BiFeO3 ceramics

KAUST Repository

Zhang, Shuxia; Wang, Lei; Chen, Yao; Wang, Dongliang; Yao, Yingbang; Ma, Yanwei

2012-01-01

High quality Bi1− x Dy x FeO3 (0 ≤ x ≤ 0.15) ceramics have been fabricated by sintering Dy-doped BiFeO3 (BFO) precursor powders at a low temperature of 780 °C. The magnetic properties of BFO were improved by the introduction of Dy on the Bi-site. More importantly, well saturated ferroelectric hysteresis loops and polarization switching currents have been observed at room temperature. A large remnant polarization (2P r) value of 62 μC/cm2 is achieved, which is the highest value reported so far for rare-earth-doped BFO ceramics. Moreover, mechanisms for improved multiferroic properties depending on chemical doping-caused structure evolutions have also been discussed.

The effects of boron on Tb0.27Dy0.73Fe2 compound

International Nuclear Information System (INIS)

Wu Lei; Chen Xicheng; Chen Xishen

1995-01-01

The magnetostrictive properties and microstructure of Tb 0.27 Dy 0.73 Fe 2 B x (x=0, 0.05, 0.1, 0.15, 0.2) have been investigated. Measurement of magnetic properties, X-ray diffraction and magnetostriction were made on Tb 0.27 Dy 0.73 Fe 2 B x polycrystalline samples prepared by arc melting. With the increase of boron content x, the iron-rich phase which leads to the detriment of magnetostrictive properties, decreases. The matrix phase of these alloys also has the MgCu 2 structure. The lattice constant and Curie transition temperature change only slightly. The doping of boron in the Tb 0.27 Dy 0.73 Fe 2 alloy can restrain the emergence of the iron-rich phase. The peritectic region probably shifts slightly with the addition of boron. ((orig.))

The use of stable isotopes in quantitative determinations of exogenous water and added ethanol in wines

Science.gov (United States)

Magdas, D. A.; Moldovan, Z.; Cristea, G.

2012-02-01

The application of oxygen isotope ratios analysis to wine water according to EU regulation no. 822/97 to determine wine's origin and also, the possible water addition to wines, gained great importance in wines authenticity control. In the natural cycle of water isotopic fractionation, during water evaporation process, the water vapors are depleted in heavy isotopes. On the other hand inside the plants take place an isotope enrichment of heavy stable isotopes of water compared with meteoric water due to photosynthesis and plants transpiration. This process makes possible the detection of exogenous water from wines 18O/16O ratios. Carbon isotopic ratios were used to estimate the supplementary addition of ethanol obtained from C4 plants (sugar cane or corn). This work presents the way in which the isotopic fingerprints (δ13C and δ18O) were used to determine the content of exogenous water from wines and the added supplementary ethanol coming from C4 plants. By using this method, the calculated values obtained for the degree of wine adulteration were in a good agreement with the real exogenous percent of water and ethanol from investigated samples.

Bulk study of a DyNiAl single crystal

Czech Academy of Sciences Publication Activity Database

Prchal, J.; Andreev, Alexander V.; Javorský, P.; Honda, F.; Jurek, Karel

272-276, - (2004), e419-e420 ISSN 0304-8853 R&D Projects: GA ČR GA106/02/0943 Keywords : rare-earth * DyNiAl * magnetic anisotropy * single crystal Subject RIV: BM - Solid Matter Physics ; Magnetism Impact factor: 1.031, year: 2004

Properties of Excited States in the 160 Dy Nucleus

Czech Academy of Sciences Publication Activity Database

Adam, Jindřich; Honusek, Milan; Dobeš, Jan

2005-01-01

Roč. 32, - (2005), s. 181-203 ISSN 1310-0157 R&D Projects: GA MŠk 1P04LA213 Institutional research plan: CEZ:AV0Z10480505 Keywords : 160Dy nucles Subject RIV: BG - Nuclear, Atomic and Molecular Physics , Colliders

Physico-chemical changes in heavy ions irradiated polymer foils by differential scanning calorimetry

International Nuclear Information System (INIS)

Ciesla, K.; Trautmann, Ch.; Vansant, E.F.

1994-01-01

The sample of commercial PETP (Hostaphan) and very heavy ions irradiated products were investigated by differential scanning calorimetry in nitrogen flow. Irradiation were performed with Dy ions of 13 MeV/u with fluences 5 x 10 10 ions/cm 2 . Differences were observed in melting behaviour of unirradiated and irradiated foils. The influence of irradiation conditions on the results was noticed. Moreover the samples of polyimide (Kapton) and polycarbonate (Macrofol) irradiated in similar conditions were examined by DSC. The DSC traces have been compared with those of unirradiated reference samples. (author). 8 refs, 5 figs

Structural, spectral, dielectric and magnetic properties of Tb–Dy doped Li-Ni nano-ferrites synthesized via micro-emulsion route

Energy Technology Data Exchange (ETDEWEB)

Junaid, Muhammad, E-mail: junaid.malik95@yahoo.com [Department of Physics, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan); Khan, Muhammad Azhar, E-mail: azhar.khan@iub.edu.pk [Department of Physics, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan); Iqbal, F. [Department of Physics, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan); Murtaza, Ghulam [Centre for Advanced Studies in Physics, Government College University, Lahore 54000 (Pakistan); Akhtar, Majid Niaz; Ahmad, Mukhtar [Department of Physics, COMSATS Institute of Information Technology, Lahore 54000 (Pakistan); Shakir, Imran [Deanship of scientific research, College of Engineering, King Saud University, PO Box 800, Riyadh 11421 (Saudi Arabia); Warsi, Muhammad Farooq [Department of Chemistry, The Islamia University of Bahawalpur, Bahawalpur 63100 (Pakistan)

2016-12-01

Terbium (Tb) and dysprosium (Dy) doped lithium-nickel nano-sized ferrites (Li{sub 0.2}Ni{sub 0.8}Tb{sub 0.5x}Dy{sub 0.5x}Fe{sub 2−x}O{sub 4} where x=0.00−0.08) were prepared by micro-emulsion technique. The X-ray diffraction (XRD) patterns confirmed the single phase cubic spinel structure. The lattice constant was increased due to larger ionic radii of Tb{sup 3+} and Dy{sup 3+} cations. The crystallite size was found in the range 30–42 nm. The FTIR (Fourier transform infrared spectroscopy) spectra revealed two significant absorption bands (~400–600 cm{sup −1}) which indicate the formation of cubic spinel structure. The peaking behavior of dielectric parameters was observed beyond 1.5 GHz. The dielectric constant and dielectric loss were found to decrease by the increase of Tb–Dy contents and frequency. The doping of Tb and Dy in Li–Ni ferrites led to increase the coercive field (120–156 Oe). The smaller magnetic and dielectric parameters suggested the possible utility of these nano-materials in switching and microwave devices applications. - Highlights: • Li{sub 0.2}Ni{sub 0.8}Tb{sub 0.5x}Dy{sub 0.5x}Fe{sub 2-x}O{sub 4} ferrites were synthesized by micro-emulsion route. • Tb and Dy addition improves coercivity while decreased saturation magnetization. • These nanomaterials can be useful in microwave and switching devices applications.

Using MASHA+TIMEPIX Setup for Registration Beta Decay Isotopes Produced in Heavy Ion Induced Reactions

Science.gov (United States)

Rodin, A. M.; Belozerov, A. V.; Chernysheva, E. V.; Dmitriev, S. N.; Gulyaev, A. V.; Gulyaeva, A. V.; Itkis, M. G.; Novoselov, A. S.; Oganessian, Yu. Ts.; Salamatin, V. S.; Stepantsov, S. V.; Vedeneev, V. Yu.; Yukhimchuk, S. A.; Krupa, L.; Granja, C.; Pospisil, S.; Kliman, J.; Motycak, S.; Sivacek, I.

2015-06-01

Radon and mercury isotopes were produced in multi nucleon transfer (48Ca + 232Th) and complete fusion (48Ca + naturalNd) reactions, respectively. The isotopes with given masses were detected using two detectors: a multi-strip detector of the well-type (made in CANBERRA) and a position-sensitive quantum counting hybrid pixel detector of the TIMEPIX type. The isotopes implanted into the detectors then emit alpha- and betaparticles until reaching the long lived isotopes. The position of the isotopes, the tracks, the time and energy of beta-particles were measured and analyzed. A new software for the particle recognition and data analysis of experimental results was developed and used. It was shown that MASHA+ TIMEPIX setup is a powerful instrument for investigation of neutron-rich isotopes far from stability limits.

The use of stable isotopes in medicinal chemistry

International Nuclear Information System (INIS)

Halliday, D.; Thompson, G.N.

1988-01-01

Stable isotopes have been employed increasingly as tracers over the last decade both to provide the clinician with the opportunity to broaden, in a quantitative manner, discrete areas of diagnosis and research, and the clinical chemist with definitive methodology for specific analyte analysis. These non-radioactive 'heavy' isotopes contain one or more extra neutrons in the nucleus compared with their more abundant 'lighter' analogues. Impetus in the application of stable isotopes for in vivo studies has come from an increased awareness of the possible harmful effects in the use of radionuclides, and a realisation of several positive advantages conferred by the use of stable isotopes in their own right - certain elements of clinical importance (especially nitrogen) lack a useable radio-nuclide equivalent; use of a 'cocktail' of stable isotopes permits a range of studies to be performed in the same patient simultaneously and, within specific constraints, serial studies can be performed in the same patients. (author)

On separation of heavy isotopes by means of selective ICRH