WorldWideScience

Sample records for health safety measures

  1. Handbook of laboratory health and safety measures

    International Nuclear Information System (INIS)

    Pal, S.B.

    1985-01-01

    The application of radioactive isotopes and various scientific instruments based on different ionizing and non-ionizing radiation have brought new safety problems to laboratory workers today. Therefore, there is a need to revise present knowledge of safety measures to deal with new hazards, thus broadening the outlook towards health and safety measures for contemporary laboratory staff. This handbook presents a series of articles on current knowledge regarding laboratory safety

  2. The Agency's Health and Safety Measures

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1960-05-31

    The Agency's health and safety measures as approved by the Board of Governors on 31 March 1960 in implementation of Articles III. A. 6 and XII of the Statute of the Agency are reproduced in this document for the information of all Members.

  3. Handbook of laboratory health and safety measures

    International Nuclear Information System (INIS)

    Pal, S.B.

    1985-01-01

    Eighteen chapters deal with all kinds of possible health and safety hazards, chemical, physical and biological, arising in laboratories. Two chapters, on X-ray hazards - diagnostic and therapeutic, and radiation protection in radionuclide investigations, respectively are indexed separately. (U.K.)

  4. Measuring and improving patient safety through health information technology: The Health IT Safety Framework.

    Science.gov (United States)

    Singh, Hardeep; Sittig, Dean F

    2016-04-01

    Health information technology (health IT) has potential to improve patient safety but its implementation and use has led to unintended consequences and new safety concerns. A key challenge to improving safety in health IT-enabled healthcare systems is to develop valid, feasible strategies to measure safety concerns at the intersection of health IT and patient safety. In response to the fundamental conceptual and methodological gaps related to both defining and measuring health IT-related patient safety, we propose a new framework, the Health IT Safety (HITS) measurement framework, to provide a conceptual foundation for health IT-related patient safety measurement, monitoring, and improvement. The HITS framework follows both Continuous Quality Improvement (CQI) and sociotechnical approaches and calls for new measures and measurement activities to address safety concerns in three related domains: 1) concerns that are unique and specific to technology (e.g., to address unsafe health IT related to unavailable or malfunctioning hardware or software); 2) concerns created by the failure to use health IT appropriately or by misuse of health IT (e.g. to reduce nuisance alerts in the electronic health record (EHR)), and 3) the use of health IT to monitor risks, health care processes and outcomes and identify potential safety concerns before they can harm patients (e.g. use EHR-based algorithms to identify patients at risk for medication errors or care delays). The framework proposes to integrate both retrospective and prospective measurement of HIT safety with an organization's existing clinical risk management and safety programs. It aims to facilitate organizational learning, comprehensive 360 degree assessment of HIT safety that includes vendor involvement, refinement of measurement tools and strategies, and shared responsibility to identify problems and implement solutions. A long term framework goal is to enable rigorous measurement that helps achieve the safety

  5. Measuring Best Practices for Workplace Safety, Health, and Well-Being: The Workplace Integrated Safety and Health Assessment.

    Science.gov (United States)

    Sorensen, Glorian; Sparer, Emily; Williams, Jessica A R; Gundersen, Daniel; Boden, Leslie I; Dennerlein, Jack T; Hashimoto, Dean; Katz, Jeffrey N; McLellan, Deborah L; Okechukwu, Cassandra A; Pronk, Nicolaas P; Revette, Anna; Wagner, Gregory R

    2018-05-01

    To present a measure of effective workplace organizational policies, programs, and practices that focuses on working conditions and organizational facilitators of worker safety, health and well-being: the workplace integrated safety and health (WISH) assessment. Development of this assessment used an iterative process involving a modified Delphi method, extensive literature reviews, and systematic cognitive testing. The assessment measures six core constructs identified as central to best practices for protecting and promoting worker safety, health and well-being: leadership commitment; participation; policies, programs, and practices that foster supportive working conditions; comprehensive and collaborative strategies; adherence to federal and state regulations and ethical norms; and data-driven change. The WISH Assessment holds promise as a tool that may inform organizational priority setting and guide research around causal pathways influencing implementation and outcomes related to these approaches.

  6. Ergonomic initiatives at Inmetro: measuring occupational health and safety.

    Science.gov (United States)

    Drucker, L; Amaral, M; Carvalheira, C

    2012-01-01

    This work studies biomechanical hazards to which the workforce of Instituto Nacional de Metrologia, Qualidade e Tecnologia Industrial (Inmetro) is exposed. It suggests a model for ergonomic evaluation of work, based on the concepts of resilience engineering which take into consideration the institute's ability to manage risk and deal with its consequences. Methodology includes the stages of identification, inventory, analysis, and risk management. Diagnosis of the workplace uses as parameters the minimal criteria stated in Brazilian legislation. The approach has several prospectives and encompasses the points of view of public management, safety engineering, physical therapy and ergonomics-oriented design. The suggested solution integrates all aspects of the problem: biological, psychological, sociological and organizational. Results obtained from a pilot Project allow to build a significant sample of Inmetro's workforce, identifying problems and validating the methodology employed as a tool to be applied to the whole institution. Finally, this work intends to draw risk maps and support goals and methods based on resiliency engineering to assess environmental and ergonomic risk management.

  7. Occupational Safety and Health Measures in Micro-scale Enterprises (MSEs) in Shiraz, Iran

    Science.gov (United States)

    Jahangiri, Mehdi; Rostamabadi, Akbar; Malekzadeh, Gholamreza; Sadi, Amin Fahandej; Hamzavi, Golnar; Rasooli, Javad; Momeni, Zahra; Ghaem, Haleh

    2016-01-01

    Objectives: This study aimed to determine the extent of implementation of occupational safety and health measures in micro-scale enterprises (MSEs) and to assess the prevalence of occupational injuries and accidents and its relationship with occupational safety and health measures provided in the MSEs. Method: A cross-sectional study was conducted among 595 of MSEs. An index called the Safety and Health Requirement Index (SHRI) was created and used to calculate the percentage of provided occupational safety and health measures. The relationship between the SHRI and the occurrence of occupational accidents and injuries was investigated with the independent samples t-test and one-way ANOVA. Results: The mean SHRI score was 60.43%, which was categorized into moderate level. Of the 30.9% of enterprises that had experienced accidents and injuries, the most common types of injuries were musculoskeletal disorders and cuts, and the least common types were pulmonary and hearing problems. Results of one-way ANOVA revealed a statistically significant relationship between the mean SHRI score and industrial branch, enterprise size, and type of accident and injury. The independent samples t-test showed that the occurrence of occupational accidents and injuries was not significantly influenced by provided health and safety measures in MSEs. Conclusion: Given the high percentage of enterprises with very poor to poor levels for the SHRI and the high prevalence of occupational accidents and injuries among the studied MSEs, feasible protective strategies and job safety training programs are required to promote occupational health and safety in the studied MSEs. PMID:27010083

  8. Occupational Safety and Health Measures in Micro-scale Enterprises (MSEs) in Shiraz, Iran.

    Science.gov (United States)

    Jahangiri, Mehdi; Rostamabadi, Akbar; Malekzadeh, Gholamreza; Sadi, Amin Fahandej; Hamzavi, Golnar; Rasooli, Javad; Momeni, Zahra; Ghaem, Haleh

    2016-05-25

    This study aimed to determine the extent of implementation of occupational safety and health measures in micro-scale enterprises (MSEs) and to assess the prevalence of occupational injuries and accidents and its relationship with occupational safety and health measures provided in the MSEs. A cross-sectional study was conducted among 595 of MSEs. An index called the Safety and Health Requirement Index (SHRI) was created and used to calculate the percentage of provided occupational safety and health measures. The relationship between the SHRI and the occurrence of occupational accidents and injuries was investigated with the independent samples t-test and one-way ANOVA. The mean SHRI score was 60.43%, which was categorized into moderate level. Of the 30.9% of enterprises that had experienced accidents and injuries, the most common types of injuries were musculoskeletal disorders and cuts, and the least common types were pulmonary and hearing problems. Results of one-way ANOVA revealed a statistically significant relationship between the mean SHRI score and industrial branch, enterprise size, and type of accident and injury. The independent samples t-test showed that the occurrence of occupational accidents and injuries was not significantly influenced by provided health and safety measures in MSEs. Given the high percentage of enterprises with very poor to poor levels for the SHRI and the high prevalence of occupational accidents and injuries among the studied MSEs, feasible protective strategies and job safety training programs are required to promote occupational health and safety in the studied MSEs.

  9. An Investigation of Health and Safety Measures in a Hydroelectric Power Plant.

    Science.gov (United States)

    Acakpovi, Amevi; Dzamikumah, Lucky

    2016-12-01

    Occupational risk management is known as a catalyst in generating superior returns for all stakeholders on a sustainable basis. A number of companies in Ghana implemented health and safety measures adopted from international companies to ensure the safety of their employees. However, there exist great threats to employees' safety in these companies. The purpose of this paper is to investigate the level of compliance of Occupational Health and Safety management systems and standards set by international and local legislation in power producing companies in Ghana. The methodology is conducted by administering questionnaires and in-depth interviews as measuring instruments. A random sampling technique was applied to 60 respondents; only 50 respondents returned their responses. The questionnaire was developed from a literature review and contained questions and items relevant to the initial research problem. A factor analysis was also carried out to investigate the influence of some variables on safety in general. Results showed that the significant factors that influence the safety of employees at the hydroelectric power plant stations are: lack of training and supervision, non-observance of safe work procedures, lack of management commitment, and lack of periodical check on machine operations. The study pointed out the safety loopholes and therefore helped improve the health and safety measures of employees in the selected company by providing effective recommendations. The implementation of the proposed recommendations in this paper, would lead to the prevention of work-related injuries and illnesses of employees as well as property damage and incidents in hydroelectric power plants. The recommendations may equally be considered as benchmark for the Safety and Health Management System with international standards.

  10. Cost-benefit comparison of nuclear and nonnuclear health and safety protective measures and regulations

    International Nuclear Information System (INIS)

    O'Donnell, E.P.; Mauro, J.J.

    1979-01-01

    This article compares the costs and benefits of health and safety measures and regulations in the nuclear and nonnuclear fields. A cost-benefit methodology for nuclear safety concerns is presented and applied to existing nuclear plant engineered safety features. Comparisons in terms of investment costs to achieve reductions in mortality rates are then made between nuclear plant safety features and the protective measures and regulations associated with nonnuclear risks, particularly with coal-fired power plants. These comparisons reveal a marked inconsistency in the cost effectiveness of health and safety policy, in which nuclear regulatory policy requires much greater investments to reduce the risk of public mortality than is required in nonnuclear areas where reductions in mortality rates could be achieved at much lower cost. A specific example of regulatory disparity regarding gaseous effluent limits for nuclear and fossil-fuel power plants is presented. It is concluded that a consistent health and safety regulatory policy based on uniform risk and cost-benefit criteria should be adopted and that future proposed Nuclear Regulatory Commission regulatory requirements should be critically evaluated from a cost-benefit viewpoint

  11. Improving health, safety and energy efficiency in New Zealand through measuring and applying basic housing standards.

    Science.gov (United States)

    Gillespie-Bennett, Julie; Keall, Michael; Howden-Chapman, Philippa; Baker, Michael G

    2013-08-02

    Substandard housing is a problem in New Zealand. Historically there has been little recognition of the important aspects of housing quality that affect people's health and safety. In this viewpoint article we outline the importance of assessing these factors as an essential step to improving the health and safety of New Zealanders and household energy efficiency. A practical risk assessment tool adapted to New Zealand conditions, the Healthy Housing Index (HHI), measures the physical characteristics of houses that affect the health and safety of the occupants. This instrument is also the only tool that has been validated against health and safety outcomes and reported in the international peer-reviewed literature. The HHI provides a framework on which a housing warrant of fitness (WOF) can be based. The HHI inspection takes about one hour to conduct and is performed by a trained building inspector. To maximise the effectiveness of this housing quality assessment we envisage the output having two parts. The first would be a pass/fail WOF assessment showing whether or not the house meets basic health, safety and energy efficiency standards. The second component would rate each main assessment area (health, safety and energy efficiency), potentially on a five-point scale. This WOF system would establish a good minimum standard for rental accommodation as well encouraging improved housing performance over time. In this article we argue that the HHI is an important, validated, housing assessment tool that will improve housing quality, leading to better health of the occupants, reduced home injuries, and greater energy efficiency. If required, this tool could be extended to also cover resilience to natural hazards, broader aspects of sustainability, and the suitability of the dwelling for occupants with particular needs.

  12. Exploring the state of health and safety management system performance measurement in mining organizations.

    Science.gov (United States)

    Haas, Emily Joy; Yorio, Patrick

    2016-03-01

    Complex arguments continue to be articulated regarding the theoretical foundation of health and safety management system (HSMS) performance measurement. The culmination of these efforts has begun to enhance a collective understanding. Despite this enhanced theoretical understanding, however, there are still continuing debates and little consensus. The goal of the current research effort was to empirically explore common methods to HSMS performance measurement in mining organizations. The purpose was to determine if value and insight could be added into the ongoing approaches of the best ways to engage in health and safety performance measurement. Nine site-level health and safety management professionals were provided with 133 practices corresponding to 20 HSMS elements, each fitting into the plan, do, check, act phases common to most HSMS. Participants were asked to supply detailed information as to how they (1) assess the performance of each practice in their organization, or (2) would assess each practice if it were an identified strategic imperative. Qualitative content analysis indicated that the approximately 1200 responses provided could be described and categorized into interventions , organizational performance , and worker performance . A discussion of how these categories relate to existing indicator frameworks is provided. The analysis also revealed divergence in two important measurement issues; (1) quantitative vs qualitative measurement and reporting; and (2) the primary use of objective or subjective metrics. In lieu of these findings we ultimately recommend a balanced measurement and reporting approach within the three metric categories and conclude with suggestions for future research.

  13. SAFETY MEASURES

    CERN Multimedia

    Relations with the Host States Service; Tel. 75152

    2001-01-01

    Following the recent terrorist attacks, the French authorities have introduced increased-vigilance measures («Vigipirate renforcé») as part of their prevention of terrorism campaign and have expressed the wish to extend these measures to the French part of the CERN site. The Organization has acceded to this request with the understanding that its international status will be respectd and has granted the French Gendarmerie right of access to the Prévessin site and to the LEP/LHC sites on French territory.

  14. Health and safety measures available for young labourers in the cottage industries of Karachi.

    Science.gov (United States)

    Baig, Lubna A; Rasheed, Shahida; Zameer, Mehvash; Zameer, Mehwash

    2005-01-01

    To determine the health problems faced by labourers, 18 years and under, working in the cottage industries of Karachi and know the safety measures available and utilized at these places. Cross-sectional study using two-stage cluster sampling. From February 2002 to March 2003, 95 cottage industries from 10 different locations of five districts of Karachi were included. All workers, 18 years and below, present were interviewed. The environmental and safety gadgets present at the industry were inspected by the surveyors and the manager was interviewed for presence of health and safety benefits for the workers. A total of 280 workers were interviewed, 26 (9.3%) children were between 9-12 years, 82 (29.3%) were between 13-15 and 172 (61.4%) were between 16-18 years of age. Health benefit was given to only one 13-year-old worker in silk industry; appropriate gadgets were absent in 93 (97.8%) industries, present only in 2 industries (one silk and one loom). First Aid box was present in only one loom industry. Two hundred and forty workers (85.7%) were unaware of the materials they were using. One hundred and ninety-three (69%) children were working in improper light, 199(71%) workers experienced high level of noise, 232(83%) were working in high temperature and 155(55.3%) were working with improper ventilation. Health problems faced included joint pains (n=64, 22.85%), backache (n=85, 30.35%), vertigo (n=48, 17.14%), numbness of fingers (n=77, 27.5%) and fatigue experienced by 143 (51.07%) children. The children and adolescents employed in cottage industry are suffering from health problems due to lack of knowledge on their part, and improper ergonomics, environmental and safety conditions at the workplace. The cottage industry should be regulated and brought under labour law. The health sector non-governmental organizations should make concerted efforts for the rehabilitation of this workforce by creating awareness and providing opportunities for education and

  15. Health and safety manual

    International Nuclear Information System (INIS)

    1980-02-01

    The manual consists of the following chapters: general policies and administration; the Environmental Health and Safety Department; the Medical Services Department: biological hazards; chemical safety; confined space entry; cryogenic safety; electrical safety; emergency plans; engineering and construction; evacuations, trenching, and shoring; fire safety; gases, flammable and compressed; guarding, mechanical; ladders and scaffolds, work surfaces; laser safety; materials handling and storage; noise; personal protective equipment; pressure safety; radiation safety, ionizing and non-ionizing; sanitation; seismic safety; training, environmental health and safety; tools, power and hand-operated; traffic and transportation; and warning signs and devices

  16. Performance Measurement and Target-Setting in California's Safety Net Health Systems.

    Science.gov (United States)

    Hemmat, Shirin; Schillinger, Dean; Lyles, Courtney; Ackerman, Sara; Gourley, Gato; Vittinghoff, Eric; Handley, Margaret; Sarkar, Urmimala

    Health policies encourage implementing quality measurement with performance targets. The 2010-2015 California Medicaid waiver mandated quality measurement and reporting. In 2013, California safety net hospitals participating in the waiver set a voluntary performance target (the 90th percentile for Medicare preferred provider organization plans) for mammography screening and cholesterol control in diabetes. They did not reach the target, and the difference-in-differences analysis suggested that there was no difference for mammography ( P = .39) and low-density lipoprotein control ( P = .11) performance compared to measures for which no statewide quality improvement initiative existed. California's Medicaid waiver was associated with improved performance on a number of metrics, but this performance was not attributable to target setting on specific health conditions. Performance may have improved because of secular trends or systems improvements related to waiver funding. Relying on condition-specific targets to measure performance may underestimate improvements and disadvantage certain health systems. Achieving ambitious targets likely requires sustained fiscal, management, and workforce investments.

  17. Measuring and controlling the mining environment for worker health and safety

    CSIR Research Space (South Africa)

    Pretorius, C

    2012-10-01

    Full Text Available Factors affecting the health and safety of Mine Workers Stress Physical Strain Fatigue Ergono- mics Silica/ Dust NIHL Heat Accidents Planisa 1. HFACS: Accident Analysis ? CSIR 2012 Slide 4 Swiss-Cheese Model illustrates how accidents...

  18. Health and Safety Assessment in Lakhra Coal Mines and Its Mitigation Measures

    Directory of Open Access Journals (Sweden)

    Sallahuddin Panhwar

    2017-04-01

    Full Text Available The coal mine excavation, transportation and coal cutting process are involved in hazards and risks that can result in fatalities, injuries and diseases, if these are not properly managed. This study has been undertaken for assessment of the safety and health issues amongst the mines workers. Convenience sampling technique was exercised upon 97 mine workers and interviewed with the help of set questionnaire. Personnel protection to workplace environment was monitored by using physical observation and scientific analysis. All parameters were measured against national and international protocols pertaining to labor law at coal mines. It has been determined that very high risk was persisting while mine excavation, coal cutting and transportation processes. Previous record of last five years was suggesting that 04 deaths happened due to roof fall, 03 fatalities occurred through suffocation by inhaling toxic gases, one causality happened via rope haulage pulley, and also one death due to stone fall down from mine shaft. 121 workers injured in different kinds of accidents within five years. It has been learnt from in-depth analysis that maximum of health risk and subsequent health damages are triggering due to lack of awareness, non-compliance of labor as well as mines laws. Thus, it is recommended that government should not allow coal mining contractors and companies, those which are failing in compliance with the suggested standards.

  19. Nuclear health and safety

    International Nuclear Information System (INIS)

    1991-04-01

    Numerous environmental, safety, and health problems found at other Department of Energy (DOE) defense nuclear facilities precipitated a review of these conditions at DOE's contractor-operated Pantex Plant, where our nation's nuclear weapons are assembled. This book focuses the review on examining key safety and health problems at Pantex and determining the need for external safety oversight of the plant

  20. Farm Health and Safety

    Science.gov (United States)

    ... the United States. Farms have many health and safety hazards, including Chemicals and pesticides Machinery, tools and ... inspection and maintenance can help prevent accidents. Using safety gloves, goggles and other protective equipment can also ...

  1. An Investigation of Health and Safety Measures in a Hydroelectric Power Plant

    Directory of Open Access Journals (Sweden)

    Amevi Acakpovi

    2016-12-01

    Conclusion: The implementation of the proposed recommendations in this paper, would lead to the prevention of work-related injuries and illnesses of employees as well as property damage and incidents in hydroelectric power plants. The recommendations may equally be considered as benchmark for the Safety and Health Management System with international standards.

  2. Environment, safety and health

    International Nuclear Information System (INIS)

    Luzianovich, L.Ch.; Fardeau, J.C.; Darras, M.

    2000-01-01

    Environment, safety and health were the three topics discussed by the WOC 8 working group of the worldwide gas congress. Environment protection has become a major preoccupation and constraint for natural gas industry at the dawn of the new millennium. It is closely linked with the safety of installation and with the health of workmen who exploit or use natural gas energy: methane emissions, health and safety in gas industry, environment management and evaluation. (J.S.)

  3. A Review and Comparative Analysis of Security Risks and Safety Measures of Mobile Health Apps

    Directory of Open Access Journals (Sweden)

    Karen Scott

    2015-11-01

    Full Text Available In line with a patient-centred model of healthcare, Mobile Health applications (mhealth apps provide convenient and equitable access to health and well-being resources and programs that can enable consumers to monitor their health related problems, understand specific medical conditions and attain personal fitness goals. This increase in access and control comes with an increase in risk and responsibility to identify and manage the associated risks, such as the privacy and security of consumers’ personal and health information. Based on a review of the literature, this paper identifies a set of risk and safety features for evaluating mHealth apps and uses those features to conduct a comparative analysis of the 20 most popular mHealth apps. The comparative analysis reveals that current mHealth apps do pose a risk to consumers. To address the safety and privacy concerns, recommendations to consumers and app developers are offered together with consideration of mHealth app future trends.

  4. Proactive prevention in occupational safety and health: how to identify tomorrow's prevention priorities and preventive measures.

    Science.gov (United States)

    Hauke, Angelika; Flaspöler, Eva; Reinert, Dietmar

    2018-04-17

    Global trends such as digitalisation, globalisation and demographic change are changing workplaces, and accordingly occupational safety and health (OSH) needs. To better prepare for the future and to foster proactive prevention, the German Social Accident Insurance (DGUV) established an OSH risk observatory (RO OSH). The RO OSH relies on an online survey and calls upon the expertise of labour inspectors. 398 labour inspectors participated in the first RO OSH enquiry. They rated developments with regard to their sector-specific relevance for OSH in the near future. The RO OSH also provides ideas for preventive measures that can be implemented by the German Social Accident Insurance Institutions. Work intensity, demographic aspects, and digitalisation play a major role for most or all sectors. However, familiar OSH issues such as musculoskeletal strain and noise also continue to be of major importance and require further consideration and specific solutions in prevention. For the DGUV, training and consulting bear great potential for proactive prevention in the above priority areas, e.g. by fostering a prevention culture and supporting companies in (psychosocial) risk assessment (also for mobile work). For instance, concepts for increasing physical activity at sedentary workplaces, and data security require continued research.

  5. Measuring patient safety culture in maternal and child health institutions in China: a qualitative study.

    Science.gov (United States)

    Wang, Yuanyuan; Liu, Weiwei; Shi, Huifeng; Liu, Chaojie; Wang, Yan

    2017-07-12

    Patient safety culture (PSC) plays a critical role in ensuring safe and quality care. Extensive PSC studies have been undertaken in hospitals. However, little is known about PSC in maternal and child health (MCH) institutions in China, which provide both population-based preventive services as well as individual care for patients. This study aimed to develop a theoretical framework for conceptualising PSC in MCH institutions in China. The study was undertaken in six MCH institutions (three in Hebei and three in Beijing). Participants (n=118) were recruited through stratified purposive sampling: 20 managers/administrators, 59 care providers and 39 patients. In-depth interviews were conducted with the participants. The interview data were coded using both inductive (based on the existing PSC theory developed by the Agency for Healthcare Research and Quality) and deductive (open coding arising from data) approaches. A PSC framework was formulated through axial coding that connected initial codes and selective coding that extracted a small number of themes. The interviewees considered patient safety in relation to six aspects: safety and security in public spaces, safety of medical services, privacy and information security, financial security, psychological safety and gap in services. A 12-dimensional PSC framework was developed, containing 69 items. While the existing PSC theory was confirmed by this study, some new themes emerged from the data. Patients expressed particular concerns about psychological safety and financial security. Defensive medical practices emerged as a PSC dimension that is associated with not only medical safety but also financial security and psychological safety. Patient engagement was also valued by the interviewees, especially the patients, as part of PSC. Although there are some common features in PSC across different healthcare delivery systems, PSC can also be context specific. In MCH settings in China, the meaning of 'patient safety

  6. Agricultural Health and Safety

    Science.gov (United States)

    ... that occur while living, working, or visiting agricultural work environments (primarily farms) are considered agricultural injuries, whether or ... of Labor's Occupational Safety & Health Administration (OSHA) supports safe and healthful working conditions by setting and enforcing standards and by ...

  7. Nanoscale reference materials for environmental, health and safety measurements: needs, gaps and opportunities.

    Science.gov (United States)

    Stefaniak, Aleksandr B; Hackley, Vincent A; Roebben, Gert; Ehara, Kensei; Hankin, Steve; Postek, Michael T; Lynch, Iseult; Fu, Wei-En; Linsinger, Thomas P J; Thünemann, Andreas F

    2013-12-01

    The authors critically reviewed published lists of nano-objects and their physico-chemical properties deemed important for risk assessment and discussed metrological challenges associated with the development of nanoscale reference materials (RMs). Five lists were identified that contained 25 (classes of) nano-objects; only four (gold, silicon dioxide, silver, titanium dioxide) appeared on all lists. Twenty-three properties were identified for characterisation; only (specific) surface area appeared on all lists. The key themes that emerged from this review were: 1) various groups have prioritised nano-objects for development as "candidate RMs" with limited consensus; 2) a lack of harmonised terminology hinders accurate description of many nano-object properties; 3) many properties identified for characterisation are ill-defined or qualitative and hence are not metrologically traceable; 4) standardised protocols are critically needed for characterisation of nano-objects as delivered in relevant media and as administered to toxicological models; 5) the measurement processes being used to characterise a nano-object must be understood because instruments may measure a given sample in a different way; 6) appropriate RMs should be used for both accurate instrument calibration and for more general testing purposes (e.g., protocol validation); 7) there is a need to clarify that where RMs are not available, if "(representative) test materials" that lack reference or certified values may be useful for toxicology testing and 8) there is a need for consensus building within the nanotechnology and environmental, health and safety communities to prioritise RM needs and better define the required properties and (physical or chemical) forms of the candidate materials.

  8. Measures taken by the French Health Minister to ensure safety in radiotherapy treatments

    International Nuclear Information System (INIS)

    Bachelot-Narquin, R.

    2009-01-01

    The objective of these measures is to restore the confidence of patients and professionals in an essential practice for the treatment of cancers and that is in constant progression. 70% of patients suffering of a cancer receive every year a radiotherapy. The national measures aim to strengthen the safety of practice, the quality of cares, the vigilance on the unwanted effects. among the measures we find in vivo dosimetry, doubling of radio physicists and then pass from 300 radio physicists in 2007 to 600 in 2012. (N.C.)

  9. Nuclear health and safety

    International Nuclear Information System (INIS)

    1990-04-01

    This report summarizes the responsiveness of DOE and contractors to findings contained in DOE technical safety appraisals and environmental surveys. These appraisals and surveys have been done at DOE facilities and sites to find out the extent of the environmental, safety, and health problems and to prioritize them for corrective action. As of January 1990, DOE computer data showed over 1,700 safety and health problems and almost 1,300 environmental problems. The majority of these problems, however, have not yet been corrected. GAO also looked at the extent to which DOE has developed a computerized tracking system to monitor the status of its environmental, safety, and health problems. GAO found that the computer system lacks important information, such as various field office and independent appraisals. Inclusion of this information would provide a more complete picture of the problems at the site

  10. Girlfriends' Health and Safety Tips

    Science.gov (United States)

    ... in Women? Women's Safety and Health Issues at Work Health Equity Girlfriends' Health and Safety Tips Recommend on Facebook Tweet Share Compartir Having friends is an important part of life. Celebrate female friendship and support your girlfriends by ...

  11. Health, safety and the environment

    International Nuclear Information System (INIS)

    1991-01-01

    The central theme of this 1990 Annual Report from British Nuclear Fuels Limited (BNFL) is that the health and safety of the public and protection of the environment are of primary concern. The report describes the fuel cycle for the production of radioactive materials used by the United Kingdom nuclear industry. Radiation protection measures undertaken by BNFL are explained as is their environmental research programme. Detailed attention is paid to the monitoring of effluent discharges into the environment and arrangements for radioactive waste disposal. The work of each BNFL site is described. The report finishes with a description of its occupational safety measures. (UK)

  12. Occupational Safety and Health Administration

    Science.gov (United States)

    ... Twitter Instagram RSS Subscribe Occupational Safety and Health Administration English | Spanish MENU OSHA English | Spanish Search A ... STATES DEPARTMENT OF LABOR Occupational Safety and Health Administration 200 Constitution Ave., NW, Washington, DC 20210 800- ...

  13. Nuclear health and safety

    International Nuclear Information System (INIS)

    1991-08-01

    This paper is a review of environmental and safety programs at facilities in the Naval Reactors Program which shows no basis for allegations that unsafe conditions exist there or that the environment is being harmed by activities conducted there. The prototype reactor design provides safety measures that are consistent with commercial nuclear power plants. Minor incidents affecting safety and the environment have occurred, however, and dents affecting safety and the environment have occurred, however, and as with other nuclear facilities, past activities have caused environmental problems that require ongoing monitoring and vigilance. While the program has historically been exempt from most oversight, some federal and state environmental oversight agencies have recently been permitted access to Naval Reactors facilities for oversight purposes. The program voluntarily cooperates with the Nuclear Regulatory Commission regarding reactor modifications, safety improvements, and component reliability. In addition, the program and its contractors have established an extensive internal oversight program that is geared toward reporting the slightest deviations from requirements or procedures. Given the program's classification policies and requirements, it does not appear that the program routinely overclassifies information to prevent its release to the public or to avoid embarrassment. However, GAO did not some instances in which documents were improperly classified

  14. Environmental, safety, and health engineering

    International Nuclear Information System (INIS)

    Woodside, G.; Kocurek, D.

    1997-01-01

    A complete guide to environmental, safety, and health engineering, including an overview of EPA and OSHA regulations; principles of environmental engineering, including pollution prevention, waste and wastewater treatment and disposal, environmental statistics, air emissions and abatement engineering, and hazardous waste storage and containment; principles of safety engineering, including safety management, equipment safety, fire and life safety, process and system safety, confined space safety, and construction safety; and principles of industrial hygiene/occupational health engineering including chemical hazard assessment, personal protective equipment, industrial ventilation, ionizing and nonionizing radiation, noise, and ergonomics

  15. The Agency's Safety Standards and Measures

    International Nuclear Information System (INIS)

    1976-04-01

    The Agency's Health and Safety Measures were first, approved by the Board of Governors on 31 March 1960 in implementation of Articles III.A.6 and XII of the Statute of the Agency. On the basis of the experience gained from applying those measures to projects carried out by Members under agreements concluded with the Agency, the Agency's Health and Safety Measures were revised in 1975 and approved by the Board of Governors on 25 February 1976. The Agency's Safety Standards and Measures as revised are reproduced in this document for the information of all Members

  16. Health and Safety First

    CERN Document Server

    2013-01-01

    At CERN, health and safety underpin everything we do. We have strict operational procedures in place, as well as health, safety and environment (HSE) requirements to make our working environment as safe as possible. It’s everyone’s responsibility to follow these procedures and requirements to keep ourselves, and our colleagues, safe. We have a very good safety and operational record at CERN stretching back almost 60 years, but there is never room for complacency.   With this very much in mind, we have developed a robust plan for implementation if something unforeseen goes wrong.  Because however careful we all are, accidents do happen, and the mark of any organisation that aspires to be among the best in the world is how quickly and efficiently it acts when they do. A small team made up of people from several departments at CERN has produced a strategic crisis management plan that we can put into action should a major incident occur.  This plan focuses on...

  17. Personal protection accessories (PPA) as a primary health safety measures in pesticide use

    International Nuclear Information System (INIS)

    Aslam, M.; Akhtar, A.; Kanwal, S.; Ali, T.; Zafar, M.I.

    2008-01-01

    Fruit growers from three districts of the Punjab took part in this study whereas their knowledge, attitude, skill and practices were evaluated regarding the use of pesticides. The hygiene and sanitation practices of the respondents were also related with proper use of PPA during pesticide spray which needs attitudinal changes along with the provision of better facilities and infrastructure. Demographic features of the fruit growers were evaluated regarding their age, qualification, marital status, source of income, smoking habits, farming size, fruit production and pesticide spraying experience. The ordinal regression model determined the significant relation among the qualification, spraying experience and land holding size with their level of knowledge and skill of using personal protection accessories (PPA). It is recommended that pesticide safety education and better skill be given to pesticide sprayers for the appropriate use of PPA. (author)

  18. Travelers' Health: Injuries and Safety

    Science.gov (United States)

    ... Safety Road Safety - 8 Steps MERS Health Advisory poster MERS Pictogram CDC Guide for Healthy Travel Website ... possible, fly on larger planes (>30 seats), in good weather, during the daylight hours, and with experienced ...

  19. Pesticide Health and Safety Information

    Science.gov (United States)

    Animal Health Safe Use Practices Pest Control Food Safety Low Risk Pesticides Integrated Pest Management directed by the product label. Pesticides may be ingested if stored improperly in food or beverage ; Environment Human Health Animal Health Safe Use Practices Food Safety Environment Air Water Soil Wildlife

  20. Health and safety annual report 1992

    International Nuclear Information System (INIS)

    1993-01-01

    BNFL operates 6 sites in the United Kingdom concerned with the nuclear fuel cycle. The annual report on occupational health and safety gives information on all aspects of health and safety within BNFL with special reference to radiation doses received by the workforce and radiation protection measures taken by the company. BNFL's safety policy is set out. Radiation doses to all workers have remained low. Other industrial accidents are also listed and its safety measures for transport, radioactive effluents and in the event of an incident, are mentioned briefly. (UK)

  1. Workplace Safety and Health Topics: Safety & Prevention

    Science.gov (United States)

    ... 1, 2018 Content source: National Institute for Occupational Safety and Health Education and Information Division Email Recommend Tweet YouTube Instagram Listen Watch RSS ABOUT About CDC Jobs Funding LEGAL Policies Privacy FOIA No Fear Act OIG 1600 Clifton Road Atlanta , GA 30329-4027 USA 800-CDC-INFO ( ...

  2. Summertime Health and Safety

    Centers for Disease Control (CDC) Podcasts

    This CDC series features topics on staying safe and healthy during the summer, whether on the road or on the water. Podcasts provide tips for general audiences on avoiding water-related injuries, driving safely, safety when outdoors, and celebrating safety on the 4th of July.

  3. Health, Safety, and Environment Division

    Energy Technology Data Exchange (ETDEWEB)

    Wade, C [comp.

    1992-01-01

    The primary responsibility of the Health, Safety, and Environmental (HSE) Division at the Los Alamos National Laboratory is to provide comprehensive occupational health and safety programs, waste processing, and environmental protection. These activities are designed to protect the worker, the public, and the environment. Meeting these responsibilities requires expertise in many disciplines, including radiation protection, industrial hygiene, safety, occupational medicine, environmental science and engineering, analytical chemistry, epidemiology, and waste management. New and challenging health, safety, and environmental problems occasionally arise from the diverse research and development work of the Laboratory, and research programs in HSE Division often stem from these applied needs. These programs continue but are also extended, as needed, to study specific problems for the Department of Energy. The results of these programs help develop better practices in occupational health and safety, radiation protection, and environmental science.

  4. Workplace measurements by the US Occupational Safety and Health Administration since 1979: descriptive analysis and potential uses for exposure assessment.

    Science.gov (United States)

    Lavoue, J; Friesen, M C; Burstyn, I

    2013-01-01

    Inspectors from the US Occupational Safety and Health Administration (OSHA) have been collecting industrial hygiene samples since 1972 to verify compliance with Permissible Exposure Limits. Starting in 1979, these measurements were computerized into the Integrated Management Information System (IMIS). In 2010, a dataset of over 1 million personal sample results analysed at OSHA's central laboratory in Salt Lake City [Chemical Exposure Health Data (CEHD)], only partially overlapping the IMIS database, was placed into public domain via the internet. We undertook this study to inform potential users about the relationship between this newly available OSHA data and IMIS and to offer insight about the opportunities and challenges associated with the use of OSHA measurement data for occupational exposure assessment. We conducted a literature review of previous uses of IMIS in occupational health research and performed a descriptive analysis of the data recently made available and compared them to the IMIS database for lead, the most frequently sampled agent. The literature review yielded 29 studies reporting use of IMIS data, but none using the CEHD data. Most studies focused on a single contaminant, with silica and lead being most frequently analysed. Sixteen studies addressed potential bias in IMIS, mostly by examining the association between exposure levels and ancillary information. Although no biases of appreciable magnitude were consistently reported across studies and agents, these assessments may have been obscured by selective under-reporting of non-detectable measurements. The CEHD data comprised 1 450 836 records from 1984 to 2009, not counting analytical blanks and erroneous records. Seventy eight agents with >1000 personal samples yielded 1 037 367 records. Unlike IMIS, which contain administrative information (company size, job description), ancillary information in the CEHD data is mostly analytical. When the IMIS and CEHD measurements of lead were merged

  5. Environment, Health, and Safety - Construction Subcontractors Documents |

    Science.gov (United States)

    NREL Environment, Health, and Safety - Construction Subcontractors Documents Environment Environment, Health and Safety (EH&S) requirements are understood by construction subcontractors and with these requirements before submitting proposals and/or environment, health and safety plans for the

  6. National Institute for Occupational Safety and Health

    Science.gov (United States)

    ... Submit Search The CDC The National Institute for Occupational Safety and Health (NIOSH) Note: Javascript is disabled or is not ... and Events NIOSH Contact Information Related Federal Agencies Occupational Safety and Health Administration Mine Safety and Health Administration Follow NIOSH ...

  7. Environment, Safety & Health at SLAC

    Science.gov (United States)

    and safety of our staff, the community, and the environment as we carry out our scientific mission. We integral to each job. As stewards of our land, SLAC also seeks to minimize pollution to our environment and to protect our resources and biota. See the SLAC Environment, Safety and Health Policy for more

  8. Safety and Health Topics: Asbestos

    Science.gov (United States)

    ... Safety and Health Program Recommendations It's the Law Poster REGULATIONS Law and Regulations Standard Interpretations Training Requirements ... page requires that javascript be enabled for some elements to function correctly. Please contact the OSHA Directorate ...

  9. Measuring safety climate in elderly homes.

    Science.gov (United States)

    Yeung, Koon-Chuen; Chan, Charles C

    2012-02-01

    Provision of a valid and reliable safety climate dimension brings enormous benefits to the elderly home sector. The aim of the present study was to make use of the safety climate instrument developed by OSHC to measure the safety perceptions of employees in elderly homes such that the factor structure of the safety climate dimensions of elderly homes could be explored. In 2010, surveys by mustering on site method were administered in 27 elderly homes that had participated in the "Hong Kong Safe and Healthy Residential Care Home Accreditation Scheme" organized by the Occupational Safety and Health Council. Six hundred and fifty-one surveys were returned with a response rate of 54.3%. To examine the factor structure of safety climate dimensions in our study, an exploratory factor analysis (EFA) using principal components analysis method was conducted to identify the underlying factors. The results of the modified seven-factor's safety climate structure extracted from 35 items better reflected the safety climate dimensions of elderly homes. The Cronbach alpha range for this study (0.655 to 0.851) indicated good internal consistency among the seven-factor structure. Responses from managerial level, supervisory and professional level, and front-line staff were analyzed to come up with the suggestion on effective ways of improving the safety culture of elderly homes. The overall results showed that managers generally gave positive responses in the factors evaluated, such as "management commitment and concern to safety," "perception of work risks and some contributory influences," "safety communication and awareness," and "safe working attitude and participation." Supervisors / professionals, and frontline level staff on the other hand, have less positive responses. The result of the lowest score in the factors - "perception of safety rules and procedures" underlined the importance of the relevance and practicability of safety rules and procedures. The modified OSHC

  10. Center for Maritime Safety and Health Studies

    Data.gov (United States)

    Federal Laboratory Consortium — Established in November 2015, the Center for Maritime Safety and Health Studies (CMSHS) promotes safety and health for all maritime workers, including those employed...

  11. Safety measuring for sodium handling

    Energy Technology Data Exchange (ETDEWEB)

    Jeong, Ji Young; Jeong, K C; Kim, T J; Kim, B H; Choi, J H

    2001-09-01

    This is the report for the safety measures of sodium handling. These contents are prerequisites for the development of sodium technology and thus the workers participate in sodium handling and experiments have to know them perfectly. As an appendix, the relating parts of the laws are presented.

  12. Health and Safety Audit Design Manual

    Energy Technology Data Exchange (ETDEWEB)

    Ternes, Mark P. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Langley, Brandon R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Accawi, Gina K. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Malhotra, Mini [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2017-10-01

    The Health and Safety Audit is an electronic audit tool developed by the Oak Ridge National Laboratory to assist in the identification and selection of health and safety measures when a home is being weatherized (i.e., receiving home energy upgrades), especially as part of the US Department of Energy (DOE) Weatherization Assistance Program, or during home energy-efficiency retrofit or remodeling jobs. The audit is specifically applicable to existing single-family homes (including mobile homes), and is generally applicable to individual dwelling units in low-rise multifamily buildings. The health and safety issues covered in the audit are grouped in nine categories: mold and moisture, lead, radon, asbestos, formaldehyde and volatile organic compounds (VOCs), combustion, pest infestation, safety, and ventilation. Development of the audit was supported by the US Department of Housing and Urban Development Office of Healthy Homes and Lead Hazard Control and the DOE Weatherization Assistance Program.

  13. Public Health Service Safety Program

    Energy Technology Data Exchange (ETDEWEB)

    McBride, J R [Southwestern Radiological Health Laboratory, Las Vegas, NV (United States)

    1969-07-01

    Off-Site Radiological Safety Programs conducted on past Plowshare experimental projects by the Southwestern Radiological Health Laboratory for the AEC will be presented. Emphasis will be placed on the evaluation of the potential radiation hazard to off-site residents, the development of an appropriate safety plan, pre- and post-shot surveillance activities, and the necessity for a comprehensive and continuing community relations program. In consideration of the possible wide use of nuclear explosives in industrial applications, a new approach to off-site radiological safety will be discussed. (author)

  14. Public Health Service Safety Program

    International Nuclear Information System (INIS)

    McBride, J.R.

    1969-01-01

    Off-Site Radiological Safety Programs conducted on past Plowshare experimental projects by the Southwestern Radiological Health Laboratory for the AEC will be presented. Emphasis will be placed on the evaluation of the potential radiation hazard to off-site residents, the development of an appropriate safety plan, pre- and post-shot surveillance activities, and the necessity for a comprehensive and continuing community relations program. In consideration of the possible wide use of nuclear explosives in industrial applications, a new approach to off-site radiological safety will be discussed. (author)

  15. Structural safety - Is the safety margin measurable

    International Nuclear Information System (INIS)

    Rintamaa, R.

    1992-01-01

    In ensuring the structural safety of the nuclear components one must be aware of the uncertainties related to the material deorientation, loadings and other operational conditions, geometrical dimensions as well as the service environment. Furthermore, the validation of the analysis tools and procedures is of great importance in overall safety assessment of a pressure retaining component. In order to identify and quantify the concerns and risks arising from the uncertainties in the safety related issue intensive research is being carried out all over the world, in particular, on the ageing, plant life extension and management of old nuclear power plants. The presentation includes a general survey of the factors relevant to the assessment of safe and reliable operation of a nuclear component throughout its planned service life. Certain aspects are outlined based on the research work being carried out at the Technical Research Centre of Finland (VTT)(orig.)

  16. One health and food safety

    DEFF Research Database (Denmark)

    Wielinga, Peter; Schlundt, Jørgen

    2014-01-01

    Many, if not most, of all important zoonoses relate in some way to animals in the food production chain. Therefore food becomes an important vehicle for many zoonotic pathogens. One of the major issues in food safety over the latest decades has been the lack of cross-sectoral collaboration across...... the food production chain. Major food safety events have been significantly affected by the lack of collaboration between the animal health, the food control, and the human health sector. One Health formulates clearly both the need for, and the benefit of cross-sectoral collaboration. Here we will focus...... on the human health risk related to zoonotic microorganisms present both in food animals and food derived from these animals, and typically transmitted to humans through food. Some diseases have global epidemic- or pandemic-potential, resulting in dramatic action from international organizations and national...

  17. Environment, Health, and Safety | NREL

    Science.gov (United States)

    -Wide Environmental Assessment 2014 (DOE/EA-1914). Final EA and FONSI Appendices. Natural and Cultural property, and the environment. View the Environmental Stewardship, Health, Safety, and Quality Management Environmental Assessment 2014. Final EA and FONSI Appendices. Download the National Wind Technology Center Site

  18. Does Employee Safety Matter for Patients Too? Employee Safety Climate and Patient Safety Culture in Health Care.

    Science.gov (United States)

    Mohr, David C; Eaton, Jennifer Lipkowitz; McPhaul, Kathleen M; Hodgson, Michael J

    2015-04-22

    We examined relationships between employee safety climate and patient safety culture. Because employee safety may be a precondition for the development of patient safety, we hypothesized that employee safety culture would be strongly and positively related to patient safety culture. An employee safety climate survey was administered in 2010 and assessed employees' views and experiences of safety for employees. The patient safety survey administered in 2011 assessed the safety culture for patients. We performed Pearson correlations and multiple regression analysis to examine the relationships between a composite measure of employee safety with subdimensions of patient safety culture. The regression models controlled for size, geographic characteristics, and teaching affiliation. Analyses were conducted at the group level using data from 132 medical centers. Higher employee safety climate composite scores were positively associated with all 9 patient safety culture measures examined. Standardized multivariate regression coefficients ranged from 0.44 to 0.64. Medical facilities where staff have more positive perceptions of health care workplace safety climate tended to have more positive assessments of patient safety culture. This suggests that patient safety culture and employee safety climate could be mutually reinforcing, such that investments and improvements in one domain positively impacts the other. Further research is needed to better understand the nexus between health care employee and patient safety to generalize and act upon findings.

  19. Nuclear health and safety

    International Nuclear Information System (INIS)

    1991-10-01

    This paper reports that GAO discussed the Department of Energy's (DOE) efforts to clean up the solar evaporation ponds at its Rocky Flats Plant in Colorado. DOE is trying to excavate the ponds used for storing and evaporating low-level radioactive and hazardous waste and stabilize the material by mixing it with concrete. DOE issue a press release in March 1991 stating that it has imposed strict cost control measures in managing the project. Yet DOE's most recent cost data show that total cleanup costs have soared to an estimated $169 million through completion in 2009-$50 million more than the amount GAO reported nine months ago. Delays have plagued the completion and approval of the managing plans for conducting and monitoring the program. Cleanup activities that DOE expected to resume by December 1990 have not yet begun. DOE will not meet the first major milestone of the solar ponds program-cleaning up the ponds and moving all the pondcrete off site by October 1991. Further, unless DOE provides enough project funding or resolves concerns over pondcrete disposal in Nevada, it will not finish pondcrete processing before Rocky Flats' interim status permit for pondcrete operations expires in November 1992

  20. Advancing Measurement of Patient Safety Culture

    Science.gov (United States)

    Ginsburg, Liane; Gilin, Debra; Tregunno, Deborah; Norton, Peter G; Flemons, Ward; Fleming, Mark

    2009-01-01

    Objective To examine the psychometric and unit of analysis/strength of culture issues in patient safety culture (PSC) measurement. Data Source Two cross-sectional surveys of health care staff in 10 Canadian health care organizations totaling 11,586 respondents. Study Design A cross-validation study of a measure of PSC using survey data gathered using the Modified Stanford PSC survey (MSI-2005 and MSI-2006); a within-group agreement analysis of MSI-2006 data. Extraction Methods Exploratory factor analyses (EFA) of the MSI-05 survey data and confirmatory factor analysis (CFA) of the MSI-06 survey data; Rwg coefficients of homogeneity were calculated for 37 units and six organizations in the MSI-06 data set to examine within-group agreement. Principal Findings The CFA did not yield acceptable levels of fit. EFA and reliability analysis of MSI-06 data suggest two reliable dimensions of PSC: Organization leadership for safety (α=0.88) and Unit leadership for safety (α=0.81). Within-group agreement analysis shows stronger within-unit agreement than within-organization agreement on assessed PSC dimensions. Conclusions The field of PSC measurement has not been able to meet strict requirements for sound measurement using conventional approaches of CFA. Additional work is needed to identify and soundly measure key dimensions of PSC. The field would also benefit from further attention to strength of culture/unit of analysis issues. PMID:18823446

  1. Occupational Safety and Health in Peru.

    Science.gov (United States)

    Cruz, Ismael; Huerta-Mercado, Raul

    2015-01-01

    Peru is a country located on the Pacific coast of South America with a population of more than 30 million inhabitants. In the past 10 years, Peru has had a steady economic growth. Peru is predominantly an extractive industry country, but the manufacturing and construction sectors are booming. It is in this context that regulations have been implemented to protect the safety and health of workers. One of the most important regulations is the Law on Safety and Health at Work, which has been recently promulgated. Regulations are complemented by training and education in occupational safety and health. The measures are yet to be fully implemented thus a positive effect in reducing accidents and occupational diseases at work has not yet been seen. Copyright © 2015 The Authors. Published by Elsevier Inc. All rights reserved.

  2. Child Safety: MedlinePlus Health Topic

    Science.gov (United States)

    ... injuries in children (Medical Encyclopedia) Also in Spanish Topic Image MedlinePlus Email Updates Get Child Safety updates ... safety Preventing head injuries in children Related Health Topics Infant and Newborn Care Internet Safety Motor Vehicle ...

  3. Health and safety in the nuclear age

    International Nuclear Information System (INIS)

    1988-01-01

    In their Communication to the Council on the development of Community measures for the application of Chapter III of the Euratom Treaty - Health and safety (COM(86) 434 final) the Commission of the European Communities announced their intention to initiate a 'Standing Conference on Health and Safety in the Nuclear Age' in order to contribute to an increase of information on nuclear activities. Following this proposition, the Commission (Directorate-General for Employment, Social Affairs and Education, Health and Safety Directorate) organized the first meeting of this Standing Conference in Luxembourg on 5, 6 and 7 October 1987 with the theme 'Information for the public and the media on health protection and safety with regard to nuclear activities'. About 120 participants representing scientific experts, the media, the bodies concerned with environmental or consumer protection, the social partners and interested national and international organizations, took part in this conference. It was the first time at European Community level that a meeting allowed an exchange of positions on the health problems related to ionizing radiation by all the parties interested in this subject. The Commission was asked to pursue this dialogue in order to improve the perception of citizens of the Community of the potential risks and the methods of protection brought into force in the nuclear field

  4. New technologies, new hazards: Need for evidence base: A report on the health status and safety measures in a biotechnology factory in Bangalore

    Directory of Open Access Journals (Sweden)

    Sudhashree V

    2007-01-01

    Full Text Available Background: In highly competitive economies, the fast-paced development of new and improved products and services inevitably spurs the development of new technologies, of which one-fifth growth has been in the biotechnology sector. Advances in technologies provide opportunities to minimize the drudgery of work and to eliminate old hazards, but they may create new currently unrecognized risks to workers. Objectives: To assess the morbidity pattern among workers in the biotechnology industry and also to find out the health and safety measures provided to the workers. Materials and Methods: A cross-sectional study was conducted in a biotechnology industry in Bangalore, which covered 779 employees who underwent health examination and blood and urine investigations; of the 779 employees, 600 were permanent employees and 179 were contract employees. Results and Discussion: The common morbidity among the workers included refractory errors; allergic contact dermatitis; hypertension; abnormal pulmonary function tests (61, 10.2%, of which 23 (37.7% were from the production department; high eosinophil count (110, 14.1%. Majority, i.e., 46 (41.8% worked in the production department. The safety measures provided to the workers are adequate, but there is a need to insist on regular use of personal protective devices by newly employed and contract laborers.

  5. Zagazig Journal of Occupational Health and Safety

    African Journals Online (AJOL)

    Zagazig Journal of Occupational Health and Safety is aimed at physicians and researchers in the wide-ranging discipline of occupational and environmental health and safety. The field is devoted to the diagnosis, prevention, management and scientific analysis of occupational , environmental and safety health problems; ...

  6. Safety climate and attitude as evaluation measures of organizational safety.

    Science.gov (United States)

    Isla Díaz, R; Díaz Cabrera, D

    1997-09-01

    The main aim of this research is to develop a set of evaluation measures for safety attitudes and safety climate. Specifically it is intended: (a) to test the instruments; (b) to identify the essential dimensions of the safety climate in the airport ground handling companies; (c) to assess the quality of the differences in the safety climate for each company and its relation to the accident rate; (d) to analyse the relationship between attitudes and safety climate; and (e) to evaluate the influences of situational and personal factors on both safety climate and attitude. The study sample consisted of 166 subjects from three airport companies. Specifically, this research was centered on ground handling departments. The factor analysis of the safety climate instrument resulted in six factors which explained 69.8% of the total variance. We found significant differences in safety attitudes and climate in relation to type of enterprise.

  7. Industrial safety and applied health physics. Annual report for 1977

    International Nuclear Information System (INIS)

    Auxier, J.A.; Davis, D.M.

    1978-06-01

    Progress is reported on the following: radiation monitoring with regard to personnel monitoring and health physics instrumentation; environs surveillance with regard to atmospheric monitoring, water monitoring, radiation background measurements, and soil and grass samples; radiation and safety surveys with regard to laboratory operations monitoring, radiation incidents, and laundry monitoring; industrial safety and special projects with regard to accident analysis, disabling injuries, and safety awards

  8. Health System Measurement Project

    Data.gov (United States)

    U.S. Department of Health & Human Services — The Health System Measurement Project tracks government data on critical U.S. health system indicators. The website presents national trend data as well as detailed...

  9. Occupational Safety and Health Curriculum Manual.

    Science.gov (United States)

    Gourley, Frank A., Jr., Comp.

    With the enactment of the Occupational Safety and Health Act of 1970, the need for manpower development in the field of industrial safety and hygiene has resulted in the development of a broad based program in Occupational Safety and Health. The manual provides information to administrators and instructors on a program of study in this field for…

  10. 77 FR 40622 - Mine Safety and Health Research Advisory Committee, National Institute for Occupational Safety...

    Science.gov (United States)

    2012-07-10

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Mine Safety and Health Research Advisory Committee, National Institute for Occupational Safety and Health (MSHRAC, NIOSH..., oxygen supply partnership, safety culture, occupational health and safety management systems, preventing...

  11. Systems engineered health and safety criteria for safety analysis reports

    International Nuclear Information System (INIS)

    Beitel, G.A.; Morcos, N.

    1993-01-01

    The world of safety analysis is filled with ambiguous words: codes and standards, consequences and risks, hazard and accident, and health and safety. These words have been subject to disparate interpretations by safety analysis report (SAR) writers, readers, and users. open-quotes Principal health and safety criteriaclose quotes has been one of the most frequently misused phrases; rarely is it used consistently or effectively. This paper offers an easily understood definition for open-quotes principal health and safety criteriaclose quotes and uses systems engineering to convert an otherwise mysterious topic into the primary means of producing an integrated SAR. This paper is based on SARs being written for environmental restoration and waste management activities for the U.S. Department of Energy (DOE). Requirements for these SARs are prescribed in DOE Order 5480-23, open-quotes Nuclear Safety Analysis Reports.close quotes

  12. The Texts of Instruments connected with the Agency's Supply of Uranium to Japan. Letters relating to the Agency's Safeguards and Health and Safety measures

    International Nuclear Information System (INIS)

    1962-01-01

    On 2 March 1962 the Director General, pursuant to a decision taken by the Board of Governors on 28 February, addressed a letter to the Governor from Japan cancelling those provisions of the letter of 24 March 1959 that related to the safeguards against diversion applicable to the JRR-3 research reactor project. On 20 June the Director General, pursuant to a decision taken by the Board on 14 June, addressed a further letter to the Governor cancelling the remaining provisions of the letter of 24 March 1959, which related to health and safety measures for the project. The texts of the two letters in question are reproduced in this document for the information of all Members

  13. Regulatory measures for traffic safety

    International Nuclear Information System (INIS)

    Veerapur, R.D.; Bharambe, S.D.; Patnaik, S.K.; Tandle, A.K.; Sonawane, K.A.; Kumar, Rajesh; Venkat Subramanian, K.

    2017-01-01

    Traffic safety is an issue related to occupational safety not restricted alone to the transportation but extends beyond. BARC has many facilities spread across large area in Mumbai and outside Mumbai. BARC deploys large number of buses, mini buses, jeeps and cars for commuting its employees to reach BARC and for commuting within BARC premises. Additionally, trucks, fire tenders, trailers etc. are also deployed for transportation of materials. No moving vehicle is ever free of the possibility of involvement in an accident. Vehicular accidents and the fatalities on road are the result of inter-play of a number of factors. The vehicle population has been steadily increasing with the pace picking up significantly in recent past. Increase in vehicle population in the face of limited road space used by a large variety of traffic has heightened the need and urgency for a well-thought-out road safety. Therefore, existence of regulatory authority to regulate traffic and vehicles to ensure safety of its employees and vehicles is very essential. BARC Traffic Safety Committee (BTSC), which is the regulating body for traffic safety is responsible for ensuring overall traffic safety. (author)

  14. Nuclear Reactor RA Safety Report, Vol. 14, Safety protection measures

    International Nuclear Information System (INIS)

    1986-11-01

    Nuclear reactor accidents can be caused by three type of errors: failure of reactor components including (1) control and measuring instrumentation, (2) errors in operation procedure, (3) natural disasters. Safety during reactor operation are secured during its design and construction and later during operation. Both construction and administrative procedures are applied to attain safe operation. Technical safety features include fission product barriers, fuel elements cladding, primary reactor components (reactor vessel, primary cooling pipes, heat exchanger in the pump), reactor building. Safety system is the system for safe reactor shutdown and auxiliary safety system. RA reactor operating regulations and instructions are administrative acts applied to avoid possible human error caused accidents [sr

  15. Occuptional Health and Safety and Employer Motivation

    DEFF Research Database (Denmark)

    Jensen, Per Langå

    2004-01-01

    It is often argued and supported by a number of case studies that investment in human factors and occupational health and safety can pay. But any employer has a number of possible in-vestments, and many of these may have a larger marginal utility than health and safety. In addition it is often...... difficult to calculate the exact pay off for human factors and health and safety – how to calculate higher motivation for instance. The economic benefit as a possible driving force for improvement of occupational health and safety is likely to exist but it must be considered a relatively weak force. Another...... important driving force for improvements in health and safety. No employer likes to be ‘branded’ as immoral, manifested in fines by the labour inspectors or media attention to an unsafe conduct. Strategies to im-prove health and safety therefore need to focus on the legitimacy as the probably strongest...

  16. Occupational Health and Safety and Employer Motivation

    DEFF Research Database (Denmark)

    Hasle, Peter; Jensen, Per Langå

    2004-01-01

    It is often argued and supported by a number of case studies that investment in human factors and occupational health and safety can pay. But any employer has a number of possible in-vestments, and many of these may have a larger marginal utility than health and safety. In addition it is often...... difficult to calculate the exact pay off for human factors and health and safety – how to calculate higher motivation for instance. The economic benefit as a possible driving force for improvement of occupational health and safety is likely to exist but it must be considered a relatively weak force. Another...... important driving force for improvements in health and safety. No employer likes to be ‘branded’ as immoral, manifested in fines by the labour inspectors or media attention to an unsafe conduct. Strategies to im-prove health and safety therefore need to focus on the legitimacy as the probably strongest...

  17. Are more restrictive food cadmium standards justifiable health safety measures or opportunistic barriers to trade? An answer from economics and public health

    International Nuclear Information System (INIS)

    Figueroa B, Eugenio

    2008-01-01

    In the past, Cd regulations have imposed trade restrictions on foodstuffs from some developing countries seeking to access markets in the developed world and in recent years, there has been a trend towards imposing more rigorous standards. This trend seems to respond more to public and private sectors strategies in some developed countries to create disguised barriers to trade and to improve market competitiveness for their industries, than to scientifically justified health precautions (sanitary and phytosanitary measures) and/or technical barriers to trade acceptable under the Uruguay Round Agreement of the WTO. Applying more rigorous Cd standards in some developed countries will not only increase production costs in developing countries but it will also have a large impact on their economies highly dependent on international agricultural markets. In the current literature there are large uncertainties in the cause-effect relationship between current levels of Cd intakes and eventual health effects in human beings; even the risk of Cd to kidney function is under considerable debate. Recent works on the importance of zinc:Cd ratio rather than Cd levels alone to determine Cd risk factors, on the one hand, and on the declining trends of Cd level in foods and soils, on the other, also indicate a lack of scientific evidence justifying more restrictive cadmium standards. This shows that developing countries should fight for changing and making more transparent the current international structures and procedures for setting sanitary and phytosanitary measures and technical barriers to trade

  18. Are more restrictive food cadmium standards justifiable health safety measures or opportunistic barriers to trade? An answer from economics and public health.

    Science.gov (United States)

    Figueroa B, Eugenio

    2008-01-15

    In the past, Cd regulations have imposed trade restrictions on foodstuffs from some developing countries seeking to access markets in the developed world and in recent years, there has been a trend towards imposing more rigorous standards. This trend seems to respond more to public and private sectors strategies in some developed countries to create disguised barriers to trade and to improve market competitiveness for their industries, than to scientifically justified health precautions (sanitary and phytosanitary measures) and/or technical barriers to trade acceptable under the Uruguay Round Agreement of the WTO. Applying more rigorous Cd standards in some developed countries will not only increase production costs in developing countries but it will also have a large impact on their economies highly dependent on international agricultural markets. In the current literature there are large uncertainties in the cause-effect relationship between current levels of Cd intakes and eventual health effects in human beings; even the risk of Cd to kidney function is under considerable debate. Recent works on the importance of zinc:Cd ratio rather than Cd levels alone to determine Cd risk factors, on the one hand, and on the declining trends of Cd level in foods and soils, on the other, also indicate a lack of scientific evidence justifying more restrictive cadmium standards. This shows that developing countries should fight for changing and making more transparent the current international structures and procedures for setting sanitary and phytosanitary measures and technical barriers to trade.

  19. Hospital safety climate surveys: measurement issues.

    Science.gov (United States)

    Jackson, Jeanette; Sarac, Cakil; Flin, Rhona

    2010-12-01

    Organizational safety culture relates to behavioural norms in the workplace and is usually assessed by safety climate surveys. These can be a diagnostic indicator on the state of safety in a hospital. This review examines recent studies using staff surveys of hospital safety climate, focussing on measurement issues. Four questionnaires (hospital survey on patient safety culture, safety attitudes questionnaire, patient safety climate in healthcare organizations, hospital safety climate scale), with acceptable psychometric properties, are now applied across countries and clinical settings. Comparisons for benchmarking must be made with caution in case of questionnaire modifications. Increasing attention is being paid to the unit and hospital level wherein distinct cultures may be located, as well as to associated measurement and study design issues. Predictive validity of safety climate is tested against safety behaviours/outcomes, with some relationships reported, although effects may be specific to professional groups/units. Few studies test the role of intervening variables that could influence the effect of climate on outcomes. Hospital climate studies are becoming a key component of healthcare safety management systems. Large datasets have established more reliable instruments that allow a more focussed investigation of the role of culture in the improvement and maintenance of staff's safety perceptions within units, as well as within hospitals.

  20. Steel Erection Safety. Module SH-39. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on steel erection safety is one of 50 modules concerned with job safety and health. This module identifies typical jobsite hazards encountered by steel erectors, as well as providing safe job procedures for general and specific construction activities. Following the introduction, 11 objectives (each keyed to a page in the text)…

  1. Safety measures in exposure room

    International Nuclear Information System (INIS)

    Muhammad Jamal Md Isa

    2004-01-01

    The contents of this chapter are follows - The exposure room: location and dimension, material and thickness, windows, doors and other openings; Position of the Irradiating Apparatus, Use of Space Adjoining the Room, Warning Signs/Light, Dark Room. Materials and Apparatus: Classification of Areas, Local Rules, Other General Safety Requirements

  2. Applied health physics and safety annual report for 1976

    International Nuclear Information System (INIS)

    Auxier, J.A.; Davis, D.M.

    1977-08-01

    Progress is reported in the following areas of research: personnel monitoring; health physics instrumentation; atmospheric monitoring; water monitoring; radiation background measurements; soil samples; laboratory operations monitoring; radiation incidents; laundry monitoring; accident analysis; and industrial safety

  3. Food Safety: MedlinePlus Health Topic

    Science.gov (United States)

    ... Food and Drug Administration) Also in Spanish Animal Cloning and Food Safety (Food and Drug Administration) Chemicals ... Bethesda, MD 20894 U.S. Department of Health and Human Services National Institutes of Health Page last updated ...

  4. The Role of OSHA in Safety and Health. Module SH-02. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on the role of OSHA (Occupational Safety and Health Act) in Safety and Health is one of 50 modules concerned with job safety and health. This module looks at the OSHA Act, its aims, and the rights and responsibilities of employers and workers under the Act. Following the introduction, 16 objectives (each keyed to a page in the…

  5. Institute for Environment, Health and Safety

    International Nuclear Information System (INIS)

    Loos, M.

    2007-01-01

    The article describes the key activities of the Institute for Environment, Health and Safety of the Belgian Nuclear Research Centre SCK-CEN. Through the performance of experiments, the development of models and the integration of human sciences in our R and D, propose new durable methods, computer codes and measuring instruments for radiation protection, management and disposal of radioactive waste and dismantling of nuclear installations. These developments belong to the disciplines environmental chemistry, radiobiology and radioecology and include the transfer of radio nuclides in the geosphere and biosphere, as also the behaviour of micro-organisms in space

  6. Risk measures in living probabilistic safety assessment

    International Nuclear Information System (INIS)

    Holmberg, J.; Niemelae, I.

    1993-05-01

    The main objectives of the study are: to define risk measures and suggested uses of them in various living PSA applications for the operational safety management and to describe specific model features required for living PSA applications. The report is based on three case studies performed within the Nordic research project Safety Evaluation by Use of Living PSA and Safety Indicators. (48 refs., 11 figs., 17 tabs.)

  7. Health and safety of the older worker.

    Science.gov (United States)

    Farrow, A; Reynolds, F

    2012-01-01

    In the UK, increasing numbers of paid employees are over 60 years with further increases expected as the state pension age rises. Some concern surrounds possible increased work-related illness and accidents for people working beyond the age of 60. To identify the available evidence for health and safety risks of workers over age 60 years with respect to factors associated with injuries and accidents. Databases searched included PUBMED, OSHUpdate, National Institute for Occupational Safety and Health (NIOSHTIC-2), SafetyLit, the UK The Health and Safety Executive (HSELINE) and the Canadian Centre for Occupational Health and Safety until December 2009. Inclusion criteria were workers aged over 60 years. Findings were grouped into occupational accidents and injuries and individual and workplace factors that may have influenced risk of injury to the over-60s. Very little direct evidence was found concerning safety practices and health risks of workers over age 60. Some safety risks were associated with specific physical declines such as age-related hearing loss. Overall, these workers had fewer accidents and injuries but these were more likely to be serious or fatal when they occurred. There was no strong evidence that work patterns, including shift work or overtime, affected safety. Protective, compensatory strategies or experience may maintain safe working practices. Implications for health and safety risks cannot be assessed without longitudinal research on workforces with substantial numbers of workers over age 60 in order to address the healthy worker effect.

  8. Industrial Student Apprenticeship: Understanding Health and Safety

    Science.gov (United States)

    Simanjuntak, M. V.; Abdullah, A. G.; Puspita, R. H.; Mahdan, D.; Kamaludin, M.

    2018-02-01

    The level of accident in industry is very high caused by lack of knowledge and awareness of workers toward the health and safety. Health and Safety are efforts to create a comfortable and productive atmosphere to accomplish a purpose or goal as maximum risk in the workplace. Vocational Education students must conduct training on business and industry, prior to that they should have a clear understanding on occupational health and safety. The purpose of this research is to analyze the understanding, preparation, and implementation of work health and safety of the students. Method used is descriptive method and data are collected using instrument, observation and interview. The result of study is conclusion of understanding occupational health and safety of vocational education students.

  9. Lessons learned from measuring safety culture: an Australian case study.

    Science.gov (United States)

    Allen, Suellen; Chiarella, Mary; Homer, Caroline S E

    2010-10-01

    adverse events in maternity care are relatively common but often avoidable. International patient safety strategies advocate measuring safety culture as a strategy to improve patient safety. Evidence suggests it is necessary to fully understand the safety culture of an organisation to make improvements to patient safety. this paper reports a case study examining the safety culture in one maternity service in Australia and considers the benefits of using surveys and interviews to understand safety culture as an approach to identify possible strategies to improve patient safety in this setting. the study took place in one maternity service in two public hospitals in NSW, Australia. Concurrently, both hospitals were undergoing an organisational restructure which was part of a major health reform agenda. The priorities of the reform included improving the quality of care and patient safety; and, creating a more efficient health system by reducing administration inefficiencies and duplication. a descriptive case study using three approaches: the safety culture was identified to warrant improvement across all six safety culture domains. There was reduced infrastructure and capacity to support incident management activities required to improve safety, which was influenced by instability from the organisational restructure. There was a perceived lack of leadership at all levels to drive safety and quality and improving the safety culture was neither a key priority nor was it valued by the organisation. the safety culture was complex as was undertaking this study. We were unable to achieve a desired 60% response rate highlighting the limitations of using safety culture surveys in isolation as a strategy to improve safety culture. Qualitative interviews provided greater insight into the factors influencing the safety culture. The findings of this study provide evidence of the benefits of including qualitative methods with quantitative surveys when examining safety culture

  10. Measuring enterprise proactiveness in managing occupational safety

    DEFF Research Database (Denmark)

    Sønderstrup-Andersen, Hans H. K.; Fløcke, Thomas; Mikkelsen, Kim Lyngby

    2010-01-01

    The aim of this paper is to communicate results, and lessons learned, from developing and applying a national questionnaire based survey for measuring the initiation of occupational safety activities in Danish enterprises and public institutions1. The survey is cross-sectional and it is part...... on the safety attitude index....

  11. Safety and health annual report 1996

    International Nuclear Information System (INIS)

    1997-01-01

    The 1996 report on the Health and Safety performance of the nuclear fuel cycle company BNFL at its sites in the United Kingdom demonstrates a continuing improvement. The site locations and developments are briefly described and international developments in subsidiary organisations noted. Other sections of the report cover health and safety policy, radiological and industrial safety, emergency planning, incidents, occupational health services, compensation scheme developments, transport, putting radiation in perspective, and safety and health research. Data are provided on: radioactive discharges; industrial safety of BNFL and contractors' employees; radiation dose summaries for BNFL and contractors' employees. There is evidence of the expected plateauing out of doses to BNFL employees at a level less than or similar to background radiation. (UK)

  12. Permanent Commission for Health and Safety

    CERN Multimedia

    Association du personnel

    2007-01-01

    The mandate of the Staff Association's permanent commission for Health and Safety is to examine all aspects of health and safety related to the working environment at CERN. In no way does it wish to be a substitute for the official bodies that are responsible for these matters. The Commission's aim is to formulate remarks on and make proposals about these questions to the relevant bodies and the CERN Management. Its main focus is the safety of the CERN staff but it is also concerned with the safety of the installations and of the CERN environment. The Commission reports to the Staff Council and the Executive Committee of the Staff Association.

  13. Improving safety culture through the health and safety organization: a case study.

    Science.gov (United States)

    Nielsen, Kent J

    2014-02-01

    International research indicates that internal health and safety organizations (HSO) and health and safety committees (HSC) do not have the intended impact on companies' safety performance. The aim of this case study at an industrial plant was to test whether the HSO can improve company safety culture by creating more and better safety-related interactions both within the HSO and between HSO members and the shop-floor. A quasi-experimental single case study design based on action research with both quantitative and qualitative measures was used. Based on baseline mapping of safety culture and the efficiency of the HSO three developmental processes were started aimed at the HSC, the whole HSO, and the safety representatives, respectively. Results at follow-up indicated a marked improvement in HSO performance, interaction patterns concerning safety, safety culture indicators, and a changed trend in injury rates. These improvements are interpreted as cultural change because an organizational double-loop learning process leading to modification of the basic assumptions could be identified. The study provides evidence that the HSO can improve company safety culture by focusing on safety-related interactions. © 2013. Published by Elsevier Ltd and National Safety Council.

  14. Health and Safety in Mobile Telephony

    International Nuclear Information System (INIS)

    Lipnjak, G.

    2001-01-01

    Full text: The paper deals with a description of mobile telephone network and the emitted radiation. The main focus is related to the potential health risks of mobile telephone radio waves. The international press has published articles warning of the risk of brain damage, hypersensitivity, eye damage, etc., if people use mobile telephones. The most important guidelines in the field of bioelectromagnetic and related to mobile telephony (ICNIRP, CENELEC and IEEE) are commented. Also, the problem of EMI of mobile telephone with other used electronic equipment by an impaired part of the human population has been elaborated. A lot of telecommunication companies provide expertise in a number of national and international standardisation groups, whose task is to monitor what is going on in the area of Health and Safety and to develop standardised measurement methods and equipment for radio-frequency electromagnetic exposure and interference. (author)

  15. Measuring Health Information Dissemination and Identifying Target Interest Communities on Twitter: Methods Development and Case Study of the @SafetyMD Network.

    Science.gov (United States)

    Kandadai, Venk; Yang, Haodong; Jiang, Ling; Yang, Christopher C; Fleisher, Linda; Winston, Flaura Koplin

    2016-05-05

    Little is known about the ability of individual stakeholder groups to achieve health information dissemination goals through Twitter. This study aimed to develop and apply methods for the systematic evaluation and optimization of health information dissemination by stakeholders through Twitter. Tweet content from 1790 followers of @SafetyMD (July-November 2012) was examined. User emphasis, a new indicator of Twitter information dissemination, was defined and applied to retweets across two levels of retweeters originating from @SafetyMD. User interest clusters were identified based on principal component analysis (PCA) and hierarchical cluster analysis (HCA) of a random sample of 170 followers. User emphasis of keywords remained across levels but decreased by 9.5 percentage points. PCA and HCA identified 12 statistically unique clusters of followers within the @SafetyMD Twitter network. This study is one of the first to develop methods for use by stakeholders to evaluate and optimize their use of Twitter to disseminate health information. Our new methods provide preliminary evidence that individual stakeholders can evaluate the effectiveness of health information dissemination and create content-specific clusters for more specific targeted messaging.

  16. Safety and Health in Nuclear Malaysia workplace

    International Nuclear Information System (INIS)

    Wo, Y.M.

    2013-01-01

    Safety and health at work place is essential to ensure the health of their workers as required under the Occupational Safety and Health Act 1994 (Act 514). In Malaysian Nuclear Agency, each building / block was appointed with one/ two supervisors, known as Area Supervisor to ensure the safety of buildings / blocks. The area supervisor will conduct periodic bimonthly inspections of the building / block under their supervision. This paper presents the results of the inspection of 80 supervisors over 45 buildings / blocks at the Malaysian Nuclear Agency for the first six months of the year 2013. (author)

  17. Safety and environmental health handbook

    Science.gov (United States)

    ,

    1989-01-01

    This Safety Handbook (445-1-H.) supplements the Geological Survey Safety Management Program objectives set forth in Survey Manual 445.1. Specifically, it provides a compact source of basic information to assist management and employees in preventing motor vehicle accidents, personal injuries, occupational diseases, fire, and other property damage or loss. All work situations incidental to the Geological Survey cannot be discussed in a handbook, and such complete coverage is not intended in this document. However, a wide range of subjects are covered in which a "common sense" approach to safety has been expressed. These subjects have been organized such that Chapters 1-5 address administrative issues, Chapters 6-12 address activities usually conducted within a facility, and Chapters 13-20 address field activities. No information contained in the Handbook is intended to alter any provision of any Federal law or executive order, Department of the Interior or Survey directive, or collective bargaining agreement. Questions or suggestions regarding the content of the Safety Handbook may be directed to the Survey Safety Manager, Administrative Division, Office of Facilities and Management Services, National Center, Reston, Virginia, Mail Stop 246. The previous edition of the Safety Handbook is superseded.

  18. Oswer integrated health and safety standard operating practices. Directive

    International Nuclear Information System (INIS)

    1993-02-01

    The directive implements the OSWER (Office of Solid Waste and Emergency Response) Integrated Health and Safety Standards Operating Practices in conjunction with the OSHA (Occupational Safety and Health Act) Worker Protection Standards, replacing the OSWER Integrated Health and Safety Policy

  19. How good is BNFL's health and safety?

    International Nuclear Information System (INIS)

    Berry, R.J.; Coulston, D.J.

    1989-01-01

    A historical perspective of the development of health and safety philosophy and practice within the nuclear industry is followed by a description of the Company's safety management system. This involves three elements, policy, implementation and audit. Data given on discharges to the environment and occupational dose. (U.K.)

  20. UMTRA Project environmental, health, and safety plan

    International Nuclear Information System (INIS)

    1989-02-01

    The basic health and safety requirements established in this plan are designed to provide guidelines to be applied at all Uranium Mill Tailings Remedial Action (UMTRA) Project sites. Specific restrictions are given where necessary. However, an attempt has been made to provide guidelines which are generic in nature, and will allow for evaluation of site-specific conditions. Health and safety personnel are expected to exercise professional judgment when interpreting these guidelines to ensure the health and safety of project personnel and the general population. This UMTRA Project Environmental, Health, and Safety (EH ampersand S) Plan specifies the basic Federal health and safety standards and special DOE requirements applicable to this program. In addition, responsibilities in carrying out this plan are delineated. Some guidance on program requirements and radiation control and monitoring is also included. An Environmental, Health, and Safety Plan shall be developed as part of the remedial action plan for each mill site and associated disposal site. Special conditions at the site which may present potential health hazards will be described, and special areas that should should be addressed by the Remedial Action Contractor (RAC) will be indicated. Site-specific EH ampersand S concerns will be addressed by special contract conditions in RAC subcontracts. 2 tabs

  1. Health and Safety annual report 1993

    International Nuclear Information System (INIS)

    1994-01-01

    In the 1993 Health and Safety Report for BNFL, data showing improvements in radiological and conventional safety are given. Other aspects discussed are emergency planning, the level of incidents, occupational health services, litigation and the compensation scheme, the transport of radioactive materials, research covering transgenerational epidemiology, mortality and cancer studies, genetics and radiobiology, and dosimetry, and finally a summary of radioactive discharges and environmental data. (UK)

  2. How Productive Is Workplace Health and Safety?

    DEFF Research Database (Denmark)

    Buhai, I. Sebastian; Cottini, Elena; Westergaard-Nielsen, Niels

    2017-01-01

    In this paper, we investigate the causal impact of workplace health and safety practices on firm performance, using Danish longitudinal matched employer–employee data merged with unique cross-sectional representative firm survey data on work environment conditions. We estimate standard production...... functions, augmented with workplace environment indicators, addressing both time-invariant and time-varying potentially relevant unobservables in the production process. We find positive and large productivity effects of improved physical dimensions of the health and safety environment, specifically...

  3. Constraints Associated With Pesticide Safety Measures Adoption ...

    African Journals Online (AJOL)

    Safety of farmers is basic to the realization of food security and agricultural transformation in developing countries globally. Most farming activities predispose farmers, non-farmers and farming communities to health hazards because some users of these hazardous substances deliberately refuse to observe necessary ...

  4. Prom Health and Safety Tips

    Science.gov (United States)

    ... cost is an issue, look for alternatives to spending a lot of money. Expensive doesn't necessarily mean better. Plan ahead for safety Tell family members or a trusted adult what your plans are ahead of time. Make an agreement with friends to check on ...

  5. Occupational health and safety services

    NARCIS (Netherlands)

    Kwantes, J.H.; Hooftman, W.; Michiel, F.

    2014-01-01

    The position, role and aim of the protective and preventive services (article 7 of the Framework directive (89/391/EEC within the legal OSH-system will be the focus point of this article. Article 13 of the EU Treaty gives the EU the possibility to draft a legal framework on occupational safety and

  6. Measuring patient safety culture in Taiwan using the Hospital Survey on Patient Safety Culture (HSOPSC).

    Science.gov (United States)

    Chen, I-Chi; Li, Hung-Hui

    2010-06-07

    Patient safety is a critical component to the quality of health care. As health care organizations endeavour to improve their quality of care, there is a growing recognition of the importance of establishing a culture of patient safety. In this research, the authors use the Hospital Survey on Patient Safety Culture (HSOPSC) questionnaire to assess the culture of patient safety in Taiwan and attempt to provide an explanation for some of the phenomena that are unique in Taiwan. The authors used HSOPSC to measure the 12 dimensions of the patient safety culture from 42 hospitals in Taiwan. The survey received 788 respondents including physicians, nurses, and non-clinical staff. This study used SPSS 15.0 for Windows and Amos 7 software tools to perform the statistical analysis on the survey data, including descriptive statistics and confirmatory factor analysis of the structural equation model. The overall average positive response rate for the 12 patient safety culture dimensions of the HSOPSC survey was 64%, slightly higher than the average positive response rate for the AHRQ data (61%). The results showed that hospital staff in Taiwan feel positively toward patient safety culture in their organization. The dimension that received the highest positive response rate was "Teamwork within units", similar to the results reported in the US. The dimension with the lowest percentage of positive responses was "Staffing". Statistical analysis showed discrepancies between Taiwan and the US in three dimensions, including "Feedback and communication about error", "Communication openness", and "Frequency of event reporting". The HSOPSC measurement provides evidence for assessing patient safety culture in Taiwan. The results show that in general, hospital staffs in Taiwan feel positively toward patient safety culture within their organization. The existence of discrepancies between the US data and the Taiwanese data suggest that cultural uniqueness should be taken into

  7. Functional safety of health information technology.

    LENUS (Irish Health Repository)

    Chadwick, Liam

    2012-03-01

    In an effort to improve patient safety and reduce adverse events, there has been a rapid growth in the utilisation of health information technology (HIT). However, little work has examined the safety of the HIT systems themselves, the methods used in their development or the potential errors they may introduce into existing systems. This article introduces the conventional safety-related systems development standard IEC 61508 to the medical domain. It is proposed that the techniques used in conventional safety-related systems development should be utilised by regulation bodies, healthcare organisations and HIT developers to provide an assurance of safety for HIT systems. In adopting the IEC 61508 methodology for HIT development and integration, inherent problems in the new systems can be identified and corrected during their development. Also, IEC 61508 should be used to develop a healthcare-specific standard to allow stakeholders to provide an assurance of a system\\'s safety.

  8. Evaluation of pesticide safety measures adopted by potato farmers ...

    African Journals Online (AJOL)

    In order to increase productivity and quality, farmers use pesticides and other agrochemicals. These pesticides if improperly handled impact negatively on the health of the users. The objective of the study was to evaluate the pesticide safety measures adopted by potato farmers in Chebiemit Division of Elgeyo/Marakwet ...

  9. Health Physics Measurements Services

    Energy Technology Data Exchange (ETDEWEB)

    Carchon, R

    2001-04-01

    SCK-CEN's programme on health physics measurements includes various activities in dosimetry, calibration , instrumentation , gamma-ray spectrometry, whole body counting , the preparation of standard sources, non-destructive assay and the maintenance of Euratom Fork detectors. Main achievements in these topical areas in 2000 are summarised.

  10. Health Physics Measurements Services

    International Nuclear Information System (INIS)

    Carchon, R.

    2001-01-01

    SCK-CEN's programme on health physics measurements includes various activities in dosimetry, calibration , instrumentation , gamma-ray spectrometry, whole body counting , the preparation of standard sources, non-destructive assay and the maintenance of Euratom Fork detectors. Main achievements in these topical areas in 2000 are summarised

  11. THE SCHOOL HEALTH AND SAFETY PROGRAM.

    Science.gov (United States)

    1963

    INVOLVING INDIVIDUALS AS WELL AS ORGANIZATIONS, THE PROGRAM AIMED AT THE OPTIMUM HEALTH OF ALL CHILDREN, AND IMPROVEMENT OF HEALTH AND SAFETY STANDARDS WITHIN THE COMMUNITY. EACH OF THE CHILDREN WAS URGED TO HAVE A SUCCESSFUL VACCINATION FOR SMALL POX, THE DPT SERIES AND BOOSTER, THE POLIO SERIES, AND CORRECTIONS OF ALL DENTAL DEFECTS AND…

  12. Developing the health, safety and environment excellence instrument.

    Science.gov (United States)

    Mohammadfam, Iraj; Saraji, Gebraeil Nasl; Kianfar, Ali; Mahmoudi, Shahram

    2013-01-07

    Quality and efficiency are important issues in management systems. To increase quality, to reach best results, to move towards the continuous improvement of system and also to make the internal and external customers satisfied, it is necessary to consider the system performance measurement. In this study the Health, Safety and Environment Excellence Instrument was represented as a performance measurement tool for a wide range of health, safety and environment management systems. In this article the development of the instrument overall structure, its parts, and its test results in three organizations are presented. According to the results, the scores ranking was the managership organization, the manufacturing company and the powerhouse construction project, respectively. The results of the instrument test in three organizations show that, on the whole, the instrument has the ability to measure the performance of health, safety and environment management systems in a wide range of organizations.

  13. Occupational health and safety issues among nurses in the Philippines.

    Science.gov (United States)

    de Castro, A B; Cabrera, Suzanne L; Gee, Gilbert C; Fujishiro, Kaori; Tagalog, Eularito A

    2009-04-01

    Nursing is a hazardous occupation in the United States, but little is known about workplace health and safety issues facing the nursing work force in the Philippines. In this article, work-related problems among a sample of nurses in the Philippines are described. Cross-sectional data were collected through a self-administered survey during the Philippine Nurses Association 2007 convention. Measures included four categories: work-related demographics, occupational injury/illness, reporting behavior, and safety concerns. Approximately 40% of nurses had experienced at least one injury or illness in the past year, and 80% had experienced back pain. Most who had an injury did not report it. The top ranking concerns were stress and overwork. Filipino nurses encounter considerable health and safety concerns that are similar to those encountered by nurses in other countries. Future research should examine the work organization factors that contribute to these concerns and strengthen policies to promote health and safety.

  14. Occupational Health and Safety Issues Among Nurses in the Philippines

    Science.gov (United States)

    de Castro, A. B.; Cabrera, Suzanne L.; Gee, Gilbert C.; Fujishiro, Kaori; Tagalog, Eularito A.

    2009-01-01

    Nursing is a hazardous occupation in the United States, but little is known about workplace health and safety issues facing the nursing work force in the Philippines. In this article, work-related problems among a sample of nurses in the Philippines are described. Cross-sectional data were collected through a self-administered survey during the Philippine Nurses Association 2007 convention. Measures included four categories: work-related demographics, occupational injury/illness, reporting behavior, and safety concerns. Approximately 40% of nurses had experienced at least one injury or illness in the past year, and 80% had experienced back pain. Most who had an injury did not report it. The top ranking concerns were stress and overwork. Filipino nurses encounter considerable health and safety concerns that are similar to those encountered by nurses in other countries. Future research should examine the work organization factors that contribute to these concerns and strengthen policies to promote health and safety. PMID:19438081

  15. Health and safety annual report 1988

    International Nuclear Information System (INIS)

    1989-01-01

    This report on health and safety provides a review of the impact of the Comapny's activities on its workforce, the public and the environment. New sections include safety auditing, emergency planning and health and safety research. BNFL operates five sites in north west England and southern Scotland. The head office and Engineering Design Centre is at Risley, near Warrington. Fuel is manufactured at Springfields near Preston, uranium is enriched for modern nuclear power stations at Capenhurst near Chester and spent fuel is reprocessed at Sellafield. BNFL also operate Calder Hall (Sellafield) and Chapelcross (Scotland) power stations and a disposal site for low-level radioactive wastes at Drigg near Sellafield. Radiation sources and BNFL's radioactive discharge are first explained generally and then specifically for each BNFL site. Industrial and radiological safety within BNFL are described. (UK)

  16. Development of a measure of safety climate

    Directory of Open Access Journals (Sweden)

    N. R. Barnes

    1990-06-01

    Full Text Available A measure of safety climate was developed to aid management in identifying safety problems and responding proactively to safety issues; to assess the general mood of the workforce to safety; and as a standard for comparison with other organizations. The measure of safety climate was based on items extracted from the Chamber of Mines "Loss Control" audit manual. Reliability analysis performed on the scale indicated consistently high reliability coefficients across three ethnic groups. Factor analysis gave support for the construct validity of the scale. Opsomming 'n Meting vir veiligheidsklimaat is ontwikkel ten einde bestuur in staat te stel om veiligheidsprobleme te identifiseer en om pro-aktiefop te tree; om die algemene gevoel van die werkskragte rakende veiligheid te bepaal en om 'n maatstaf vir vergelyking met ander organisasies daar te stel. 'n Betroubaarheidssanalise wat op die skaal uitgevoer is het daarop gedui dat daar konsekwent hoe betroubaarheidskoefisiënte vir drie etniese groepe verkry word. 'n Faktoranalise het die konstrukgeldigheid van die skaal bevestig. The author acknowledges the financial assistance provided by the Human Sciences Research Council for this research.

  17. PERCEPTION OF BUILDING CONSTRUCTION WORKERS TOWARDS SAFETY, HEALTH AND ENVIRONMENT

    Directory of Open Access Journals (Sweden)

    C.R. CHE HASSAN

    2007-12-01

    Full Text Available The construction industry is known as one of the most hazardous activities. Therefore, safety on the job site is an important aspect with respect to the overall safety in construction. This paper assesses the safety level perception of the construction building workers towards safety, health and environment on a construction job site in Kuala Lumpur, Malaysia. The above study was carried out by choosing 5 selected large building construction projects and 5 small building construction projects respectively in and around Kuala Lumpur area. In the present study, an exhaustive survey was carried out in these 10 project site areas using a standard checklist and a detailed developed questionnaire. The checklist comprised 17 divisions of safety measurements which are considered and perceived to be important from the safety point of view and was assessed based on the score obtained. The questionnaire comprised the general information with 36 safety attitude statements on a 1-5 Likert scale which was distributed to 100 construction workers. The results of the checklist show the difference of safety levels between the large and small projects. The study revealed that the large projects shown a high and consistent level in safety while the small projects shown a low and varied safety levels. The relationship between the factors can be obtained from the questionnaire. They are organizational commitment, factor influencing communication among workmates, worker related factors, personal role and supervisors’ role factors, obstacles to safety and safe behavior factors and management commitment at all levels in line with the management structure and risk taking behavioral factors. The findings of the present study revealed invaluable indications to the construction managers especially in improving the construction workers’ attitude towards safety, health and environment and hence good safety culture in the building construction industries.

  18. Neutron nuclear data measurements for criticality safety

    Directory of Open Access Journals (Sweden)

    Guber Klaus

    2017-01-01

    Full Text Available To support the US Department of Energy Nuclear Criticality Safety Program, neutron-induced cross section experiments were performed at the Geel Electron Linear Accelerator of the Joint Research Center Site Geel, European Union. Neutron capture and transmission measurements were carried out using metallic natural cerium and vanadium samples. Together with existing data, the measured data will be used for a new evaluation and will be submitted with covariances to the ENDF/B nuclear data library.

  19. Environmental, health, and safety by design

    International Nuclear Information System (INIS)

    Soklow, R.G.

    1999-01-01

    Solar Turbines Incorporated created a self-directed work team, the Safety and Environmental Awareness (SEA) Team that initiated a company wide effort to raise employee awareness to promote integrating responsible environmental, health, and safety practices into product design, manufacturing, and services. Environmental, health, and safety issues influence how all businesses operate around the world. Companies choose to operate in an environmentally responsible manner because it not only benefits employees and the communities where they live, it also benefits the business when superior performance results in a competitive advantage. Solar surveyed gas turbines users to identify their top environmental and safety concerns and issues. The authors asked about various environmental and safety aspects of their equipment. Results from the survey has helped engineering and design focus efforts so that future products and product improvements assist customers in meeting their regulatory obligations and social responsibilities. Air pollution has historically been one of the most important environmental issues facing customers, because pollutant emissions greatly influence equipment choices and operation flexibility. There are other environmental, health and safety issues: sustainable fire suppression choices, start systems, hazardous materials use and ability to recycle materials, package accessibility, noise and product take back issues

  20. Gardening Health and Safety Tips

    Science.gov (United States)

    ... or who take certain medications (i.e. for depression, insomnia, or poor circulation). Eat healthy foods to help keep you energized. Extreme Heat Keep Your Cool in Hot Weather Tips for persons with disabilities and physical activity. Talk to your health care provider if you have physical, mental, or ...

  1. Environment, health and safety guiding principles

    International Nuclear Information System (INIS)

    1997-06-01

    The Canadian Energy Pipeline Association (CEPA) has taken a leadership role in promoting responsible planning, management and work practices that meet the pipeline industry's environment, health and safety objectives. This brochure contains CEPA's environment, health and safety statement. It lists the guiding principles developed and endorsed by CEPA and its member companies in support of protecting the environment and the health and safety of its employees and the public. The 11 CEPA member companies are: Alberta Natural Gas Company Ltd., ATCO Gas Services Ltd., Foothills Pipe Lines Ltd., Interprovincial Pipe Line Inc., NOVA Gas Transmission Limited, TransGas Limited, Trans Mountain Pipe Line Company Ltd., Trans-Northern Pipelines Inc., Trans Quebec and Maritimes Pipeline Inc., and Westcoast Energy Inc

  2. Integrating environment health and safety management at Petro-Canada

    International Nuclear Information System (INIS)

    Raymond, G.

    1993-01-01

    Petro-Canada has developed a tool to integrate, measure, and improve its management systems of environment, health, and safety (EH ampersand S). This tool, called the Total Loss Management System, is described in the areas of general management issues, policies and procedures, evaluations, organization, stewardship, issue management, and performance measures. Petro-Canada's policies on occupational health and safety are consistent with its environmental policy, being structured in the same way. An integrated audit system is used to cover health, safety, industrial hygiene, reliability, environment, and risk management. EH ampersand S matters are integrated at the corporate level in a separate department. Regional divisions review EH ampersand S performance every month, incidents are discussed, and preventive measures are taken as necessary. Regional performances are combined every quarter for ultimate presentation to the Petro-Canada board. New or emerging issues that may affect divisions are assigned an issue sponsor, a member of divisional management who makes sure the issue receives the resources necessary to study and define its impact. Examples of issues include soil contamination, process hazard management, and benzene exposure limits. Performance measures flow from the corporate environment and occupational health and safety policies, and come in two types: those that measure activities to improve performance and those that measure the outcome of the activities

  3. 76 FR 71345 - Patient Safety Organizations: Voluntary Relinquishment From Child Health Patient Safety...

    Science.gov (United States)

    2011-11-17

    ... Organizations: Voluntary Relinquishment From Child Health Patient Safety Organization, Inc. AGENCY: Agency for... notification of voluntary relinquishment from Child Health Patient Safety Organization, Inc. of its status as a Patient Safety Organization (PSO). The Patient Safety and Quality Improvement Act of 2005 (Patient Safety...

  4. Stepping Up Occupational Safety and Health Through Employee Participation.

    Science.gov (United States)

    Vaughan, Gary R.

    1986-01-01

    The effectiveness of the Occupational Safety and Health Act of 1970 is examined, and it is suggested that employee participation could help improve occupational safety and health in the future, through safety committees, safety circles, safety teams, and individual participation. (MSE)

  5. Nature-Based Strategies for Improving Urban Health and Safety.

    Science.gov (United States)

    Kondo, Michelle C; South, Eugenia C; Branas, Charles C

    2015-10-01

    Place-based programs are being noticed as key opportunities to prevent disease and promote public health and safety for populations at-large. As one key type of place-based intervention, nature-based and green space strategies can play an especially large role in improving health and safety for dwellers in urban environments such as US legacy cities that lack nature and greenery. In this paper, we describe the current understanding of place-based influences on public health and safety. We focus on nonchemical environmental factors, many of which are related to urban abandonment and blight. We then review findings from studies of nature-based interventions regarding impacts on health, perceptions of safety, and crime. Based on our findings, we suggest that further research in this area will require (1) refined measures of green space, nature, and health and safety for cities, (2) interdisciplinary science and cross-sector policy collaboration, (3) observational studies as well as randomized controlled experiments and natural experiments using appropriate spatial counterfactuals and mixed methods, and (4) return-on-investment calculations of potential economic, social, and health costs and benefits of urban greening initiatives.

  6. Building a safety culture in global health: lessons from Guatemala.

    Science.gov (United States)

    Rice, Henry E; Lou-Meda, Randall; Saxton, Anthony T; Johnston, Bria E; Ramirez, Carla C; Mendez, Sindy; Rice, Eli N; Aidar, Bernardo; Taicher, Brad; Baumgartner, Joy Noel; Milne, Judy; Frankel, Allan S; Sexton, J Bryan

    2018-01-01

    Programmes to modify the safety culture have led to lasting improvements in patient safety and quality of care in high-income settings around the world, although their use in low-income and middle-income countries (LMICs) has been limited. This analysis explores (1) how to measure the safety culture using a health culture survey in an LMIC and (2) how to use survey data to develop targeted safety initiatives using a paediatric nephrology unit in Guatemala as a field test case. We used the Safety, Communication, Operational Reliability, and Engagement survey to assess staff views towards 13 health climate and engagement domains. Domains with low scores included personal burnout, local leadership, teamwork and work-life balance. We held a series of debriefings to implement interventions targeted towards areas of need as defined by the survey. Programmes included the use of morning briefings, expansion of staff break resources and use of teamwork tools. Implementation challenges included the need for education of leadership, limited resources and hierarchical work relationships. This report can serve as an operational guide for providers in LMICs for use of a health culture survey to promote a strong safety culture and to guide their quality improvement and safety programmes.

  7. 75 FR 44967 - National Institute for Occupational Safety and Health

    Science.gov (United States)

    2010-07-30

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES National Institute for Occupational Safety and Health... Occupational Safety and Health (NIOSH), Department of Health and Human Services (HHS). ACTION: Notice. SUMMARY... Occupational Safety and Health (NIOSH), 4676 Columbia Parkway, MS C-46, Cincinnati, OH 45226, Telephone 877-222...

  8. Radiological Emergency Response Health and Safety Manual

    Energy Technology Data Exchange (ETDEWEB)

    D. R. Bowman

    2001-05-01

    This manual was created to provide health and safety (H&S) guidance for emergency response operations. The manual is organized in sections that define each aspect of H and S Management for emergency responses. The sections are as follows: Responsibilities; Health Physics; Industrial Hygiene; Safety; Environmental Compliance; Medical; and Record Maintenance. Each section gives guidance on the types of training expected for managers and responders, safety processes and procedures to be followed when performing work, and what is expected of managers and participants. Also included are generic forms that will be used to facilitate or document activities during an emergency response. These ensure consistency in creating useful real-time and archival records and help to prevent the loss or omission of information.

  9. Occupational Safety and Health Management System (OSHMS)

    International Nuclear Information System (INIS)

    Shyen, A.K.S.; Mohd Khairul Hakimin; Manisah Saedon

    2011-01-01

    Safe work environment has always been one of the major concerns at workplace. For this, Occupational Safety and Health Act 1994 has been promulgated for all workplaces to ensure the Safety, Health and Welfare of its employees and any person at workplaces. Malaysian Nuclear Agency therefore has started the initiative to review and improve the current Occupational Safety and Health Management System (OSHMS) by going for OHSAS 18001:2007 and MS 1722 standards certification. This would also help in our preparation to bid as the TSO (Technical Support Organization) for the NPP (Nuclear Power Plant) when it is established. With a developed and well maintained OSHMS, it helps to create a safe working condition and thus enhancing the productivity, quality and good morale. Ultimately, this will lead to a greater organization profit. However, successful OSHMS requires full commitment and support from all level of the organization to work hand in hand in implementing the safety and health policy. Therefore it is essential for all to acknowledge the progress of the implementation and be part of it. (author)

  10. Health and safety annual report 1989

    International Nuclear Information System (INIS)

    1989-01-01

    This 1989 annual report on Health and Safety in BNFL is intended to give the public a general review of the impact of the Company's activities on its workforce, the public and the environment. The activities at Sellafield, Springfields, Chapelcross, Drigg and Capenhurst are outlined, together with sections on medical services and transport, and radiation monitoring of workforce and the environment. (author)

  11. Towards an occupational safety and health culture

    NARCIS (Netherlands)

    Zwetsloot, G.I.J.M.; Steijger, N.

    2014-01-01

    Occupational safety and health (OSH) is a highly regulated area that appears to be based on rational planning and logical management approaches, e.g. OSM Management Systems: employers and employees of organisations should be aware of OSH risks, assess these risks systematically, provide the

  12. EM Health and Safety Plan Guidelines

    Energy Technology Data Exchange (ETDEWEB)

    1994-12-01

    This document contains information about the Health and Safety Plan Guidelines. Topics discussed include: Regulatory framework; key personnel; hazard assessment; training requirements; personal protective equipment; extreme temperature disorders or conditions; medical surveillance; exposure monitoring/air sampling; site control; decontamination; emergency response/contingency plan; emergency action plan; confined space entry; and spill containment.

  13. 10 CFR 851.23 - Safety and health standards.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Safety and health standards. 851.23 Section 851.23 Energy DEPARTMENT OF ENERGY WORKER SAFETY AND HEALTH PROGRAM Specific Program Requirements § 851.23 Safety and..., “Marine Terminals.” (6) Title 29 CFR, Part 1918, “Safety and Health Regulations for Longshoring.” (7...

  14. Recognizing Job Health Hazards. Module SH-08. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on recognizing job health hazards is one of 50 modules concerned with job safety and health. This module presents the four general categories of environmental conditions or stresses: chemical, physical, biological, and ergonomic. Following the introduction, 14 objectives (each keyed to a page in the text) the student is…

  15. Workplace safety and health for the veterinary health care team.

    Science.gov (United States)

    Gibbins, John D; MacMahon, Kathleen

    2015-03-01

    Veterinary clinic employers have a legal and ethical responsibility to provide a safe and healthy workplace. Clinic members are responsible for consistently using safe practices and procedures set up by their employer. Development and implementation of a customized comprehensive workplace safety and health program is emphasized, including an infection control plan. Occupational safety and health regulations are reviewed. The hazards of sharps, animal bites and scratches, and drugs are discussed. Strategies to prevent or minimize adverse health effects and resources for training and education are provided. Published by Elsevier Inc.

  16. Benchmarking of World Health Organization surgical safety checklist

    International Nuclear Information System (INIS)

    Messahel, Farouk M.; AlQahtani, Ali S.

    2009-01-01

    To compare the quality of our services with the World Health Organization (WHO) surgical safety recommendations as a reference, to improve our services if they fall short of that of the WHO, and to publish our additional standards, so that they may be included in future revision of WHO checklist. We conducted this study on 15th July 2008 at the Armed Forces Hospital, Wadi Al-Dawasir, Kingdom of Saudi Arabia. We compared each WHO safety standard item with its corresponding standard in our checklist. There were 4 possibilities for the comparison: that our performance meet, was less than or exceeded the quality-of-care measures in the WHO checklist, or that there are additional safety measures in either checklist that need to be considered by each party. Since its introduction in 1997, our checklist was applied to 11828 patients and resulted in error-free outcomes. Benchmarking proved that our surgical safety performance does not only match the standards of the WHO surgical safety checklist, but also exceeds it in other safety areas (for example measures to prevent perioperative hypothermia and venous thromboembolism). Benchmarking is a continuous quality improvement process aimed at providing the best available at the time in healthcare, and we recommend its adoption by healthcare providers. The WHO surgical safety checklist is a bold step in the right direction towards safer surgical outcomes. Feedback from other medical establishments should be encouraged. (author)

  17. Electrical safety in health care area

    International Nuclear Information System (INIS)

    Amer, G.M.

    2011-01-01

    An electrical safety in health care area is necessary to protect patients and staff from potential electrical hazards.Functional, accurate and safe clinical equipment is an essential requirement in the provision of health services. Well-maintained equipment will give clinicians greater confidence in the reliability of its performance and contribute to a high standard of client care. Clinical equipment, like all health services, requires annual or periodic servicing of medical equipment. In addition to planned servicing and preventative maintenance, there may be the unexpected failure of medical (and other) equipment, necessitating repair. In general, clinical equipment that has an electrical power source and has direct contact with the client must be serviced as a first priority. In this presentation, a review of the main concepts related to the electrical safety in health area,theinternational standard, the distribution of electric power in hospital and protection against shockwill be introduced. Protection system in hospital will be presented in its two ways: inpower distribution in hospitaland inbiomedical equipment design,finally the optimum maintenance technology and safety tests in health care areawill presented also.

  18. Environment, health and safety progress report 1997

    International Nuclear Information System (INIS)

    1998-01-01

    Imperial Oil is Canada's largest producer of crude oil and a major producer of natural gas. It is also the largest refiner and marketer of petroleum products, sold mainly under the Esso brand. Imperial Oil, in participation with Syncrude Canada, is also a major developer of the oil sands reserves in Cold Lake, Alberta. This review of environmental and health and safety performance in 1997 highlights the Company's comprehensive approach to risk management to reduce risk to safety, health and the environment. It is noted that in 1997, the Company's employee and contractor safety performance continued to be among the best in the industry. Potentially hazardous incidents decreased as a consequence of Imperial Oil's more stringent health and safety management system. Environmental compliance notifications fell by more than half in 1997. During the year there was a slight increase in hazardous wastes, due to the loss of outlets for recycling some materials. The National Pollutants Release Inventory indicates that Imperial has reduced emissions and offsite transfers by 25 per cent since 1993. Volatile organic compounds have been reduced by 60 per cent since 1993. According to the report all Imperial Oil facilities operate well within the guidelines for sulphur dioxide emissions. 1 tab., 10 figs

  19. PUREX Deactivation Health and Safety documentation

    International Nuclear Information System (INIS)

    Dodd, E.N. III.

    1995-01-01

    The purpose of the PUREX Deactivation Project is to establish a passively safe and environmentally secure configuration of PUREX at the Hanford Site, and to preserve that configuration for a 10-year horizon. The 10-year horizon is used to predict future maintenance requirements and represents they typical time duration expended to define, authorize, and initiate the follow-on Decontamination and Decommissioning (D ampersand D) activities. This document was prepared to increase attention to worker safety issues during the deactivation project and, as such, identifies the documentation and programs associated with PUREX Deactivation Health and Safety

  20. Health, safety and environmental research program

    International Nuclear Information System (INIS)

    Dinner, P.J.

    1983-01-01

    This report outlines the Health, Safety and Environmental Research Program being undertaken by the CFFTP. The Program objectives, relationship to other CFFTP programs, implementation plans and expected outputs are stated. Opportunities to build upon the knowledge and experience gained in safely managing tritium in the CANDU program, by addressing generic questions pertinent to tritium safety for fusion facilities, are identified. These opportunities exist across a broad spectrum of issues covering the anticipated behaviour of tritium in fusion facilities, the surrounding environment and in man

  1. Environment, safety, and health manual, closeout report

    International Nuclear Information System (INIS)

    1975-12-01

    A coordination draft of the Environment, Safety, and Health (ES and H) manual was submitted on 2 September 1975. Comments provided by Operational Safety personnel were being incorporated by a task team when the effort was terminated on 31 October 1975. This report documents the development history of the manual and provides a status of the manual up to the time the efforts were discontinued. Also discussed are issues which effect completion of the manual. Additionally a plan for completion of the manual is suggested

  2. PUREX Deactivation Health and Safety documentation

    Energy Technology Data Exchange (ETDEWEB)

    Dodd, E.N. III

    1995-01-01

    The purpose of the PUREX Deactivation Project is to establish a passively safe and environmentally secure configuration of PUREX at the Hanford Site, and to preserve that configuration for a 10-year horizon. The 10-year horizon is used to predict future maintenance requirements and represents they typical time duration expended to define, authorize, and initiate the follow-on Decontamination and Decommissioning (D&D) activities. This document was prepared to increase attention to worker safety issues during the deactivation project and, as such, identifies the documentation and programs associated with PUREX Deactivation Health and Safety.

  3. 75 FR 56549 - National Institute for Occupational Safety and Health (NIOSH), Safety and Occupational Health...

    Science.gov (United States)

    2010-09-16

    ... Suites Hotel, 1900 Diagonal Road, Alexandria, Virginia, 22314, Telephone (703) 684-5900, Fax (703) 684... conduct of Study Section business and for the study section to consider safety and occupational health...

  4. 77 FR 27776 - Safety and Occupational Health Study Section (SOHSS), National Institute for Occupational Safety...

    Science.gov (United States)

    2012-05-11

    ... Occupational Health Study Section (SOHSS), National Institute for Occupational Safety and Health (NIOSH) In... Services Office, CDC, pursuant to Public Law 92-463. Purpose: The Safety and Occupational Health Study... standard grants review and funding cycles pertaining to research issues in occupational safety and health...

  5. 76 FR 18220 - Safety and Occupational Health Study Section (SOHSS), National Institute for Occupational Safety...

    Science.gov (United States)

    2011-04-01

    ... Occupational Health Study Section (SOHSS), National Institute for Occupational Safety and Health (NIOSH) In... Services Office, CDC, pursuant to Public Law 92-463. Purpose: The Safety and Occupational Health Study... standard grants review and funding cycles pertaining to research issues in occupational safety and health...

  6. 75 FR 12554 - Mine Safety and Health Research Advisory Committee, National Institute for Occupational Safety...

    Science.gov (United States)

    2010-03-16

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Mine Safety and Health Research Advisory Committee, National Institute for Occupational Safety and Health (MSHRAC, NIOSH... priorities in mine safety and health research, including grants and contracts for such research, 30 U.S.C...

  7. 75 FR 26266 - Safety and Occupational Health Study Section (SOHSS), National Institute for Occupational Safety...

    Science.gov (United States)

    2010-05-11

    ... Occupational Health Study Section (SOHSS), National Institute for Occupational Safety and Health (NIOSH) In...) Public Law 92-463. Purpose: The Safety and Occupational Health Study Section will review, discuss, and... cycles pertaining to research issues in occupational safety and health, and allied areas. It is the...

  8. 78 FR 40743 - Mine Safety and Health Research Advisory Committee, National Institute for Occupational Safety...

    Science.gov (United States)

    2013-07-08

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Mine Safety and Health Research Advisory Committee, National Institute for Occupational Safety and Health (MSHRAC, NIOSH... Director, NIOSH, on priorities in mine safety and health research, including grants and contracts for such...

  9. Occupational Safety and Health in Venezuela.

    Science.gov (United States)

    Caraballo-Arias, Yohama

    2015-01-01

    Venezuela has pioneered a preventive-focused and comprehensive movement for Occupational Safety and Health (OSH) in Latin America. However, despite being an oil-rich country, it has some of the lowest salaries for their workers and highest levels of hyperinflation, devaluation, crime, and violence of the world. Review the current status and challenges on relevant aspects of OSH in Venezuela. Review of literature and documents from national governments, UN agencies, NGOs, and the Venezuelan government concerning OSH and related topics since 1986. Reformed in 2005, the Organic Law on Prevention, Conditions and Environment (LOPCYMAT) was a fundamental moment of change for OSH. Factors which have impacted OSH the strongest are (i) the creation of the National Institute of Occupational Safety and Health (INPSASEL) and (ii) the socioeconomic crisis Venezuela is going through. Venezuela's laws are innovative and yet non-compliance is enormous. Almost half of the population works in the informal sector. Following the International Labor Office projections, 5 people die per day in Venezuela due to occupational accidents or diseases, making health and safety at work a luxury rather than a right. The quality of life for the average worker has deteriorated, affecting not only health but the overall well-being of all Venezuelans. The political and socio-economic situation has led to a mass exodus of more than 1.6 million highly qualified and talented professionals. Many statistics concerning OSH are not updated and are unreliable regarding occupational accidents and diseases. There is a substantial difference between what is written to protect individual Venezuelans in the workplace and the reality of workplace conditions. Substantial governmental actions are needed in the immediate future to improve occupational safety and health of Venezuelan workers. Copyright © 2015 The Author. Published by Elsevier Inc. All rights reserved.

  10. Defining and Measuring Safety Climate: A Review of the Construction Industry Literature.

    Science.gov (United States)

    Schwatka, Natalie V; Hecker, Steven; Goldenhar, Linda M

    2016-06-01

    Safety climate measurements can be used to proactively assess an organization's effectiveness in identifying and remediating work-related hazards, thereby reducing or preventing work-related ill health and injury. This review article focuses on construction-specific articles that developed and/or measured safety climate, assessed safety climate's relationship with other safety and health performance indicators, and/or used safety climate measures to evaluate interventions targeting one or more indicators of safety climate. Fifty-six articles met our inclusion criteria, 80% of which were published after 2008. Our findings demonstrate that researchers commonly defined safety climate as perception based, but the object of those perceptions varies widely. Within the wide range of indicators used to measure safety climate, safety policies, procedures, and practices were the most common, followed by general management commitment to safety. The most frequently used indicators should and do reflect that the prevention of work-related ill health and injury depends on both organizational and employee actions. Safety climate scores were commonly compared between groups (e.g. management and workers, different trades), and often correlated with subjective measures of safety behavior rather than measures of ill health or objective safety and health outcomes. Despite the observed limitations of current research, safety climate has been promised as a useful feature of research and practice activities to prevent work-related ill health and injury. Safety climate survey data can reveal gaps between management and employee perceptions, or between espoused and enacted policies, and trigger communication and action to narrow those gaps. The validation of safety climate with safety and health performance data offers the potential for using safety climate measures as a leading indicator of performance. We discuss these findings in relation to the related concept of safety culture and

  11. Performance scorecard for occupational safety and health management systems

    Directory of Open Access Journals (Sweden)

    Hernâni Veloso Neto

    2012-06-01

    Full Text Available The pro-active and systematic search for best performances should be the two assumptions of any management system, so safety and health management in organizations must also be guided by these same precepts. However, the scientific production evidences that the performance evaluation processes in safety and health continue to be guided, in their essence, by intermittency, reactivity and negativity, which are not consistent with the assumptions referenced above. Therefore, it is essential that health and safety at work management systems (HSW MS are structured from an active and positive viewpoint, focusing on continuous improvement. This implies considering performance evaluation processes that incorporate, on the one hand, monitoring, measuring and verification procedures, and on the other hand, structured matrixes of results that capture the key factors of success, by mobilizing both reactive and proactive indicators. One of the instruments that can fulfill these precepts of health and safety performance evaluation is the SafetyCard, a performance scorecard for HSW MS that we developed and will seek to outline and demonstrate over this paper.

  12. Linking better shiftwork arrangements with safety and health management systems

    OpenAIRE

    Kogi, Kazutaka

    2004-01-01

    OBJECTIVE: Various support measures useful for promoting joint change approaches to the improvement of both shiftworking arrangements and safety and health management systems were reviewed. A particular focus was placed on enterprise-level risk reduction measures linking working hours and management systems. METHODS: Voluntary industry-based guidelines on night and shift work for department stores and the chemical, automobile and electrical equipment industries were examined. Survey results t...

  13. Safety measures for NPP Mochovce - Skoda contribution

    International Nuclear Information System (INIS)

    Svec, P.

    1997-01-01

    Brief technical descriptions are given of the following issues involved in safety measures: reactor pressure vessel embrittlement and its monitoring; non-destructive testing; integrity of the steam generator primary collector; integrity of steam generator heat exchanging tubes; distribution of feedwater in the steam generator; the hazard of plugging water collectors located on the steam generator room floor; steam generator level control valves; primary circuit venting under emergency conditions; diagnostic systems installed in the primary circuit; monitoring of reactor pressure vessel head leaks; severity of containment leaks; turbine missiles; seismic design; procedures for normal operation; and operation limits and conditions. (M.D.)

  14. 77 FR 11120 - Patient Safety Organizations: Voluntary Relinquishment From UAB Health System Patient Safety...

    Science.gov (United States)

    2012-02-24

    ... Organizations: Voluntary Relinquishment From UAB Health System Patient Safety Organization AGENCY: Agency for... notification of voluntary relinquishment from the UAB Health System Patient Safety Organization of its status as a Patient Safety Organization (PSO). The Patient Safety and Quality Improvement Act of 2005...

  15. Work, obesity, and occupational safety and health.

    Science.gov (United States)

    Schulte, Paul A; Wagner, Gregory R; Ostry, Aleck; Blanciforti, Laura A; Cutlip, Robert G; Krajnak, Kristine M; Luster, Michael; Munson, Albert E; O'Callaghan, James P; Parks, Christine G; Simeonova, Petia P; Miller, Diane B

    2007-03-01

    There is increasing evidence that obesity and overweight may be related, in part, to adverse work conditions. In particular, the risk of obesity may increase in high-demand, low-control work environments, and for those who work long hours. In addition, obesity may modify the risk for vibration-induced injury and certain occupational musculoskeletal disorders. We hypothesized that obesity may also be a co-risk factor for the development of occupational asthma and cardiovascular disease that and it may modify the worker's response to occupational stress, immune response to chemical exposures, and risk of disease from occupational neurotoxins. We developed 5 conceptual models of the interrelationship of work, obesity, and occupational safety and health and highlighted the ethical, legal, and social issues related to fuller consideration of obesity's role in occupational health and safety.

  16. Tritium radioluminescent devices, Health and Safety Manual

    Energy Technology Data Exchange (ETDEWEB)

    Traub, R.J.; Jensen, G.A.

    1995-06-01

    This document consolidates available information on the properties of tritium, including its environmental chemistry, its health physics, and safe practices in using tritium-activated RL lighting. It also summarizes relevant government regulations on RL lighting. Chapters are divided into a single-column part, which provides an overview of the topic for readers simply requiring guidance on the safety of tritium RL lighting, and a dual-column part for readers requiring more technical and detailed information.

  17. MATURATION PYRAMID OF OCCUPATIONAL HEALTH AND SAFETY

    OpenAIRE

    Perçin, Fatih; Haydan, Eren

    2017-01-01

    Occupational Health and Safety System (OHS) isimportant for governments, employers and workers. Recently, OHS program hasdeveloped day by day and tried to secure working environment. For this purpose,it is necessary that the written job security rulesin the workplace should be internalized by employees, and employers, andgovernment system. Workers can comply from the top to the bottom oforganization and contribute to development of rules through their own personalknowledge, experience, and in...

  18. Tritium radioluminescent devices, Health and Safety Manual

    International Nuclear Information System (INIS)

    Traub, R.J.; Jensen, G.A.

    1995-06-01

    This document consolidates available information on the properties of tritium, including its environmental chemistry, its health physics, and safe practices in using tritium-activated RL lighting. It also summarizes relevant government regulations on RL lighting. Chapters are divided into a single-column part, which provides an overview of the topic for readers simply requiring guidance on the safety of tritium RL lighting, and a dual-column part for readers requiring more technical and detailed information

  19. Accounting for Health and Safety costs

    DEFF Research Database (Denmark)

    Rikhardsson, Pall M.

    A part of the emerging sustainability management accounting is corporate health and safety performance. One performance dimension is the costs of occupational accidents in companies. The underlying logic for calculating these costs is that if occupational accidents are prevented then these costs...... could be avoided. This chapter presents and discusses selected methods for calculating the costs of occupational accidents. The focus is on presenting the characteristics of each method and disclosing the benefits and drawbacks of each method...

  20. Worksite health and safety climate: scale development and effects of a health promotion intervention.

    Science.gov (United States)

    Basen-Engquist, K; Hudmon, K S; Tripp, M; Chamberlain, R

    1998-01-01

    Environmental influences on health and health behavior have an important place in research on worksite health promotion. We tested the validity and internal consistency of a new measure of organizational health and safety climate that was used in a large randomized trial of a worksite cancer prevention program (the Working Well Trial). The resulting scales then were applied to assess intervention effects. This study uses data from a subset of 40 worksites in the Working Well Trial. Employees at 20 natural gas pipeline worksite and 20 rural electrical cooperatives completed a cross-sectional questionnaire at baseline and 3-year follow-up. A factor analysis of this self-report instrument produced a two-factor solution. The resulting health and safety climate scales had good internal consistency (Cronbach's alpha = 0.74 and 0.82, respectively) and concurrent validity. The health climate scale was correlated more highly with organizational measures that were indicative of a supportive health climate than those indicating supportive safety climate, while the reverse was true of the safety climate scale. Changes in health climate were associated with the number of smoking and smokeless tobacco programs offered at the worksites at the time of the 3-year follow-up (r = 0.46 and 0.42, respectively). The scales were not correlated with most employee health behaviors. The health climate scores increased at intervention worksites, compared with scores at control worksites (F[1,36] = 7.57, P = 0.009). The health and safety climate scales developed for this study provide useful instruments for measuring organizational change related to worksite health promotion activities. The Working Well Intervention resulted in a significant improvement in worksite health climate.

  1. Occupational health and safety: Designing and building with MACBETH a value risk-matrix for evaluating health and safety risks

    Science.gov (United States)

    Lopes, D. F.; Oliveira, M. D.; Costa, C. A. Bana e.

    2015-05-01

    Risk matrices (RMs) are commonly used to evaluate health and safety risks. Nonetheless, they violate some theoretical principles that compromise their feasibility and use. This study describes how multiple criteria decision analysis methods have been used to improve the design and the deployment of RMs to evaluate health and safety risks at the Occupational Health and Safety Unit (OHSU) of the Regional Health Administration of Lisbon and Tagus Valley. ‘Value risk-matrices’ (VRMs) are built with the MACBETH approach in four modelling steps: a) structuring risk impacts, involving the construction of descriptors of impact that link risk events with health impacts and are informed by scientific evidence; b) generating a value measurement scale of risk impacts, by applying the MACBETH-Choquet procedure; c) building a system for eliciting subjective probabilities that makes use of a numerical probability scale that was constructed with MACBETH qualitative judgments on likelihood; d) and defining a classification colouring scheme for the VRM. A VRM built with OHSU members was implemented in a decision support system which will be used by OHSU members to evaluate health and safety risks and to identify risk mitigation actions.

  2. Environment, safety and health progress assessment manual

    International Nuclear Information System (INIS)

    1992-12-01

    On June 27, 1989, the Secretary of Energy announced a 1O-Point Initiative to strengthen environment,safety, and health (ES ampersand H) programs, and waste management activities at involved conducting DOE production, research, and testing facilities. One of the points independent Tiger Team Assessments of DOE operating facilities. The Office of Special Projects (OSP), EH-5, in the Office of the Assistant Secretary for Environment, Safety and Health, EH-1, was assigned the responsibility to conduct the Tiger Team Assessments. Through June 1992, a total of 35 Tiger Team Assessments were completed. The Secretary directed that Corrective Action Plans be developed and implemented to address the concerns identified by the Tiger Teams. In March 1991, the Secretary approved a plan for assessments that are ''more focused, concentrating on ES ampersand H management, ES ampersand H corrective actions, self-assessment programs, and root-cause related issues.'' In July 1991, the Secretary approved the initiation of ES ampersand H Progress Assessments, as a followup to the Tiger Team Assessments, and in the continuing effort to institutionalize the self-assessment process and line management accountability in the ES ampersand H areas. This volume contains appendices to the Environment, Safety and Health Progress Assessment Manual

  3. Zagazig Journal of Occupational Health and Safety: About this journal

    African Journals Online (AJOL)

    Zagazig Journal of Occupational Health and Safety: About this journal. Journal Home > Zagazig Journal of Occupational Health and Safety: About this journal. Log in or Register to get access to full text downloads.

  4. To Your Health: NLM update transcript - Gun safety strategies

    Science.gov (United States)

    ... transcript040918.html To Your Health: NLM update Transcript Gun safety strategies : 04/09/2018 To use the ... on weekly topics. An evidence-based, public health gun safety strategy that is consistent with second amendment ...

  5. Measuring Population Health Outcomes

    OpenAIRE

    Parrish, R. Gibson

    2010-01-01

    An ideal population health outcome metric should reflect a population's dynamic state of physical, mental, and social well-being. Positive health outcomes include being alive; functioning well mentally, physically, and socially; and having a sense of well-being. Negative outcomes include death, loss of function, and lack of well-being. In contrast to these health outcomes, diseases and injuries are intermediate factors that influence the likelihood of achieving a state of health. On the basis...

  6. Food safety measurement issues. Way forward

    International Nuclear Information System (INIS)

    Venkatesh Iyengar

    2013-01-01

    Ensuring food safety (FS) is a persistent concern frequently faced by many countries. Safeguarding the quality of food that is fit for human consumption is the primary responsibility of the governmental regulatory agencies. For most part, agro-industries and food processors assume voluntary leadership for producing safe food. However, in the event of FS breach, the regulatory responsibility kicks into identify and rectify the situation. Notwithstanding whether it is the regulator or the industry that institutes the remedial action (e.g. improved hygiene and refined agricultural and manufacturing practices), the role of laboratory measurements is central in safeguarding the integrity of a functioning FS system. There are many analytical tools available to implement this task, such as validated analytical methods, natural matrix reference materials, field tested monitoring systems (proactive assessment) and effective surveillance systems (constant vigilance to prevent repeat safety violations). Way forward: existing FS tools are insufficient and should be strengthened with innovative approaches. Examples are: assembling swift intervention logistics to face FS breaches; rapid response systems including communication; robust metrology based measurement systems located at strategic locations in the country; and inter-disciplinary human resource to match the need for capacity development. These issues are discussed. (author)

  7. Quadrant I RCRA Facility investigation work plan: Health and safety plan

    International Nuclear Information System (INIS)

    1990-01-01

    This report describes occupational health and safety issues at the Portsmouth Gaseous Diffusion Plant. Health effects from exposure to chemicals, vapors, drilling and sampling activities, as well as from ionizing radiations and protective measures are discussed

  8. Safety culture measurements results in the agricultural sector

    OpenAIRE

    Terjék, László

    2013-01-01

    The author examined the safety culture and in relation to that the safety and health-related human factors. The examination was conducted primarily in the agricultural sector. Safety culture is also a key factor in business life especially in productive sectors. Basically, it determines the general work safety and occupational hazard situations, which may have an impact on business, competitiveness, and efficiency, and also employee satisfaction.The concept of safety culture is new in the app...

  9. Recent Cases: Administrative Law--Occupational Safety and Health Act

    Science.gov (United States)

    Harvard Law Review, 1976

    1976-01-01

    Implications of the Occupational Safety and Health Act of 1970 are described in two cases: Brennan v. Occupational Safety and Health Review Commission (Underhill Construction Corp.), and Anning-Johnson Co. v. United States Occupational Safety and Health Review Commission. (LBH)

  10. 29 CFR 1925.2 - Safety and health standards.

    Science.gov (United States)

    2010-07-01

    .... Every contractor and subcontractor shall comply with the safety and health standards published in 41 CFR... 29 Labor 7 2010-07-01 2010-07-01 false Safety and health standards. 1925.2 Section 1925.2 Labor Regulations Relating to Labor (Continued) OCCUPATIONAL SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR...

  11. Health and safety at DNE [Dounreay Nuclear Power Development Establishment

    International Nuclear Information System (INIS)

    Walford, J.G.; Tyler, G.R.

    1988-11-01

    This report reviews health and safety experience at the UKAEA's Dounreay Nuclear Power Development Establishment for 1986 and gives relevant data in the fields of health physics and general safety. It includes sections on: organization, policy and training; monitoring of the working environment; personnel monitoring; protection of the public; radiological incidents; and non-radiological health and safety. (author)

  12. 32 CFR 989.27 - Occupational safety and health.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 6 2010-07-01 2010-07-01 false Occupational safety and health. 989.27 Section... PROTECTION ENVIRONMENTAL IMPACT ANALYSIS PROCESS (EIAP) § 989.27 Occupational safety and health. Assess direct and indirect impacts of proposed actions on the safety and health of Air Force employees and...

  13. 20 CFR 401.160 - Health or safety.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Health or safety. 401.160 Section 401.160... INFORMATION Disclosure of Official Records and Information § 401.160 Health or safety. The Privacy Act allows us to disclose information in compelling circumstances where an individual's health or safety is...

  14. 10 CFR 871.2 - Public health and safety exemption.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 4 2010-01-01 2010-01-01 false Public health and safety exemption. 871.2 Section 871.2 Energy DEPARTMENT OF ENERGY AIR TRANSPORTATION OF PLUTONIUM § 871.2 Public health and safety exemption... property damage, or other significant threat to the public health and safety. [42 FR 48332, Sept. 23, 1977...

  15. Measurement of Food Safety Culture using Survey and Maturity Profiling Tools

    OpenAIRE

    Jespersen, Lone; Griffiths, Mansel; Maclaurin, Tanya; Chapman, Ben; Wallace, Carol A.

    2016-01-01

    Organizational culture is defined by dimensions and characteristics that can be used to measure food safety culture in food manufacturing through a food safety maturity model. Maturity models from quality, health care, and information technology have been used since early 1970 and this work presents a novel food safety culture maturity model with five capability areas and food safety pinpointed behaviours specific to functions and levels in a food manufacturing company. A survey tool linked t...

  16. Health innovation for patient safety improvement

    Directory of Open Access Journals (Sweden)

    Renukha Sellappans

    2013-01-01

    Full Text Available Medication error has been identified as a major factor affecting patient safety. Many innovative efforts such as Computerised Physician Order Entry (CPOE, a Pharmacy Information System, automated dispensing machines and Point of Administration Systems have been carried out with the aim of improving medication safety. However, areas remain that require urgent attention. One main area will be the lack of continuity of care due to the breakdown of communication between multiple healthcare providers. Solutions may include consideration of “health smart cards” that carry vital patient medical information in the form of a “credit card” or use of the Malaysian identification card. However, costs and technical aspects associated with the implementation of this health smart card will be a significant barrier. Security and confidentiality, on the other hand, are expected to be of primary concern to patients. Challenges associated with the implementation of a health smart card might include physician buy-in for use in his or her everyday practice. Training and technical support should also be available to ensure the smooth implementation of this system. Despite these challenges, implementation of a health smart card moves us closer to seamless care in our country, thereby increasing the productivity and quality of healthcare.

  17. Health innovation for patient safety improvement.

    Science.gov (United States)

    Sellappans, Renukha; Chua, Siew Siang; Tajuddin, Nur Amani Ahmad; Mei Lai, Pauline Siew

    2013-01-01

    Medication error has been identified as a major factor affecting patient safety. Many innovative efforts such as Computerised Physician Order Entry (CPOE), a Pharmacy Information System, automated dispensing machines and Point of Administration Systems have been carried out with the aim of improving medication safety. However, areas remain that require urgent attention. One main area will be the lack of continuity of care due to the breakdown of communication between multiple healthcare providers. Solutions may include consideration of "health smart cards" that carry vital patient medical information in the form of a "credit card" or use of the Malaysian identification card. However, costs and technical aspects associated with the implementation of this health smart card will be a significant barrier. Security and confidentiality, on the other hand, are expected to be of primary concern to patients. Challenges associated with the implementation of a health smart card might include physician buy-in for use in his or her everyday practice. Training and technical support should also be available to ensure the smooth implementation of this system. Despite these challenges, implementation of a health smart card moves us closer to seamless care in our country, thereby increasing the productivity and quality of healthcare.

  18. The impact of health and safety committees. A study based on survey, interview, and Occupational Safety and Health Administration data.

    Science.gov (United States)

    Boden, L I; Hall, J A; Levenstein, C; Punnett, L

    1984-11-01

    In a study conducted to determine if the existence of a joint labor-management health and safety committee (HSC) was correlated with either the number of Occupational Safety and Health Administration (OSHA) complaints or hazardousness, as measured by OSHA serious citations, virtually no effect could be detected in a sample of 127 Massachusetts manufacturing firms. At a sample of 13 firms, interviews of HSC members were conducted. Committee attributes and perceptions about committee effectiveness were compared with the number of OSHA complaints and serious citations. There were fewer complaints and fewer serious citations at firms with HSCs that were perceived as effective. Results of the study suggest that the objective attributes of the committee may be less important to its success than the commitment of management and labor to solving workplace safety problems.

  19. Environment, Safety, Health and Waste Management Plan

    International Nuclear Information System (INIS)

    1988-01-01

    The mission of the Feed Materials Production Center (FMPC) is the production of high qaulity uranium metal for use by the US Department of Energy (DOE) in Defense Programs. In order to accomplish this mission and to maintain the FMPC as a viable facility in the DOE production complex, the facility must be brought into full compliance with all federal and state regulations and industry standards for environmental protection and worker safety. Where past practices have resulted in environmental insult, a comprehensive program of remediation must be implemented. The purpose of this combined Environment, Safety, Health and Waste Management Plan is to provide a road map for achieving needed improvements. The plan is structured to provide a comprehensive projection from the current fiscal year (FY) through FY 1994 of the programs, projects and funding required to achieve compliance. To do this, the plan is subdivided into chapters which discuss the applicable regulations;project schedules and funding requirements;details of the various programs for environment, safety, health and waste management;details of the ongoing National Environmental Policy Act (NEPA);the quality assurance program and the environmental monitoring program. 14 refs., 30 figs., 29 tabs

  20. Passenger safety, health, and comfort: a review.

    Science.gov (United States)

    Rayman, R B

    1997-05-01

    Since the birth of aviation medicine approximately 80 yrs ago, practitioners and scientists have given their attention primarily to flight deck crew, cabin crew, and ground support personnel. However, in more recent years we have broadened our horizons to include the safety, health, and comfort of passengers flying commercial aircraft. This will be even more compelling as more passengers take to the air in larger aircraft and flying longer hours to more distant destinations. Further, we can expect to see more older passengers because people in many countries are living longer, healthier lives. The author first discusses the stresses imposed by ordinary commercial flight upon travelers such as airport tumult, barometric pressure changes, immobility, jet lag, noise/ vibration, and radiation. Medical considerations are next addressed describing inflight illness and medical care capability aboard U.S. air carriers. Passenger safety, cabin air quality, and the preventive medicine aspects of air travel are next reviewed in the context of passenger safety, health, and comfort. Recommendations are addressed to regulator agencies, airlines aircraft manufacturers, and the aerospace medicine community.

  1. Occupational safety and health law handbook

    Energy Technology Data Exchange (ETDEWEB)

    Sarvadi, D.G. [ed.; Keller; Heckman

    1999-09-01

    This book reviews the regulations and standards governing the protection of employees in the workplace and provides insight into dealing with pertinent regulations and regulatory authorities. Written for safety professionals, industrial hygienists, human resource professionals, attorneys, and students, this companion to Government Institutes' best-selling ``Environmental Law Handbook'' offers the legal fundamentals behind occupational safety and health laws in one concise and authoritative volume. In 19 chapters, the authoring law firm of Keller and Heckman cover the OSHAct and its development; OSHA, NIOSH, and OSHRC; the roles played by other regulatory agencies; the OSHA rulemaking process; OSHA Standards and the General Duty Clause; record keeping and reporting; employers' and employees' rights; inspections; violations, penalties, and how to contest them; criminal prosecutions; state plans; industry-specific issues; OSHA reform; and international regulations and standards. This book references approximately 400 seminal OSHA legal decisions from the approximately 1,300 cases on record and includes coverage of Canadian and European Community regulations, making it the first comprehensive global overview of occupational safety and health law.

  2. Safety

    International Nuclear Information System (INIS)

    1998-01-01

    A brief account of activities carried out by the Nuclear power plants Jaslovske Bohunice in 1997 is presented. These activities are reported under the headings: (1) Nuclear safety; (2) Industrial and health safety; (3) Radiation safety; and Fire protection

  3. Health and safety of older nurses.

    Science.gov (United States)

    Letvak, Susan

    2005-01-01

    The nursing workforce is aging at an unprecedented rate yet little is known about the health and safety of older registered nurses (RNs). The survey reported here examined the relationships between demographic variables, job attributes (job satisfaction, control over practice, and job demands) and the physical and mental health and job-related injuries and health disorders of 308 nurses over the age of 50. Findings indicate that nurses with higher job satisfaction, higher control over practice, and lower job demands experienced increased physical health. Increasing age was positively correlated with mental health. Almost a quarter of older RNs experienced a job-related injury within the past 5 years, and over a third experienced job-related health problems. Nurses with higher job demands and those employed in hospital settings were more likely to have an injury. Overall, older RNs reported higher levels of physical and mental health than the national norm. Efforts must be made to keep older RNs healthy so we can retain them in the workforce.

  4. Telecommuting: Occupational health considerations for employee health and safety.

    Science.gov (United States)

    Healy, M L

    2000-06-01

    1. Information technology has moved "work" out of a centralized location. Employees who telecommute pose significant challenges and considerations for the practice of occupational health nursing. 2. Employer and employee benefits associated with telecommuting are reportedly associated with high levels of job satisfaction. However, the occupational health and safety risks of this new work environment need to be fully assessed and understood. 3. The ergonomic controls to minimize the risk of repetitive motion injuries are the same for both office and home locations. Additional attention need to be paid to implementing risk controls for other physical hazards and psychosocial considerations, as well as personal safety and security issues. 4. The scope of occupational health nursing practice needs to remain dynamic, recognizing the impact new technologies have on the workplace, to continue to meet the needs of the changing workplace.

  5. An airport occupational health and safety management system from the OHSAS 18001 perspective.

    Science.gov (United States)

    Dejanović, Dejana; Heleta, Milenko

    2016-09-01

    Occupational health and safety represents a set of technical, medical, legal, psychological, pedagogical and other measures with the aim to detect and eliminate hazards that threaten the lives and health of employees. These measures should be applied in a systematic way. Therefore, the aim of this study is to review occupational health and safety legislation in Serbia and the requirements that airports should fulfill for Occupational Health and Safety Assessment Series certification. Analyzing the specificity of airport activities and injuries as their outcomes, the article also proposes preventive measures for the health and safety of employees. Furthermore, the airport activities which are the most important from the standpoint of risks are defined, as the goals for occupational health and safety performance improvement.

  6. Mobile phones and health, stakeholder perspectives: occupational health and safety

    International Nuclear Information System (INIS)

    Benke, G.

    2001-01-01

    The use of mobile phones for business and social purposes has attracted concerns regarding possible health impacts. Their use in the workplace has potential for significant exposure. In this paper I outline the role of the occupational health and safety (OHS) professional and the way hazard, risk and dose are defined in the workplace. Also discussed are the other important aspects that need to be considered with exposure to radio-frequency radiation (RFR) from mobile phone exposure in the workplace and current concerns about the possible health effects from workplace exposure. Copyright (2001) Australasian Radiation Protection Society Inc

  7. Magnetic resonance: safety measures and biological effects

    International Nuclear Information System (INIS)

    Gordillo, I.; Lafuente, J.; Fernandez, C.; Barbero, M.J.; Cascon, E.

    1997-01-01

    The biological effects of electromagnetic fields is currently a subject of great controversy. For this reason, magnetic resonance imaging (MRI) and spectroscopy are constantly under investigation. The source of the risk in MRI is associated with the three types of electromagnetic radiation to which the patient is exposed: the static magnetic field, variable (gradient) magnetic fields and radiofrequency fields. Each is capable of producing significant biological effects when employed at sufficient intensity. Patients exposed to risk sources are those situated within the lines of force of the magnetic field, ellipsoid lines that are arranged around the magnet, representing the strength of the surrounding field. To date, at the intensity normally utilized in MRI(<2T) and respecting the field limit recommendations established by the US Food and Drug Administration (FDA) for clinical use of this technique no adverse secondary biological effects have been reported. The known biological effects and other possible secondary effects are reviewed, and the recommended safety measures are discussed. (Author)

  8. Safety measure S 05 'Sump clogging risk'

    International Nuclear Information System (INIS)

    Murani, J.

    1997-01-01

    This paper dealt with the safety measure S 05 'Sump clogging risk'. Problem specification contains: (1) to determine the effective strainer surface needed to be available in order to assure sufficient coolant volumes for a reliable operation of emergency systems; (2) to determine quantity and structure of insulation material which can be dislodged and can induce strained clogging; (3) to verify properties of insulation material with regard to its thermal degradation as a result of a long-term reactor unit operation; (4) to design and erect strainers so to assure sufficient congestion of emergency pump intake lines in post-accident regimes; (5) to design seismically resistant strainers with a capability to resist dynamic impacts from adjacent piping; (6) to assure monitoring of the strainer condition in real time with signals sent to the main control room

  9. Economic evaluation of occupational safety preventive measures in a hospital.

    Science.gov (United States)

    Ramos, Delfina G; Arezes, Pedro M; Afonso, Paulo

    2015-01-01

    When an organization performs an integrated analysis of risks through its Occupational Health and Safety Management System, several steps are suggested to address the implications of the identified risks. Namely, the organization should make a detailed analysis of the monetary impact for the organization of each of the preventive measures considered. However, it is also important to perform an analysis of the impact of each measure on society (externalities). The aim of this paper is to present a case study related to the application of the proposed economic evaluation methodology. An analysis of the work accidents in a hospital has been made. Three of the major types of accidents have been selected: needle stings, falls and excessive strain. Following the risk assessment, some preventive measures have been designed. Subsequently, the Benefit/Cost ratio (B/C) of these measures has been calculated, both in financial terms (from the organization's perspective) and in economic terms (including the benefits for the worker and for the Society). While the financial ratio is only advantageous in some cases, when the externalities are taken into account, the B/C ratio increases significantly. It is important to consider external benefits to make decisions concerning the implementation of preventive measures in Occupational Health and Safety projects.

  10. Occupational Health and Safety Management and Turnover Intention in the Ghanaian Mining Sector.

    Science.gov (United States)

    Amponsah-Tawiah, Kwesi; Ntow, Michael Akomeah Ofori; Mensah, Justice

    2016-03-01

    The mining industry is considered as one of the most dangerous and hazardous industries and the need for effective and efficient occupational health and safety management is critical to safeguard workers and the industry. Despite the dangers and hazards present in the mining industry, only few studies have focused on how occupational health and safety and turnover intentions in the mines. The study suing a cross-sectional survey design collected quantitative data from the 255 mine workers that were conveniently sampled from the Ghanaian mining industry. The data collection tools were standardized questionnaires that measured occupational health and safety management and turnover intentions. These scales were also pretested before their usage in actual data collection. The correlation coefficient showed that a negative relationship existed between dimensions of occupational health and safety management and turnover intention; safety leadership (r = -0.33, p safety facilities and equipment (r = -0.32, p safety procedure (r = -0.27, p safety leadership and safety facility were significant predictors of turnover intention, (β = -0.28, p safety leadership in ensuring the effective formulation of policies and supervision of occupational health and safety at the workplace. The present study demonstrates that safety leadership is crucial in the administration of occupational health and safety and reducing turnover intention in organizations.

  11. Measuring population health in Moldova: health expectancies

    Directory of Open Access Journals (Sweden)

    Cristina Avram

    2018-05-01

    Full Text Available Health measures are decisive for the development and implementation of population health policies. Monitoring health indicators can lead to improvements in health and decrease in the inequalities among subpopulations. The life expectancy at birth for the Moldovan population did not increase considerably during the last decades, due to the social and economic crisis which led to high mortality and poor health. In Moldova, no aggregated health indicators are utilized for health monitoring. Therefore, the authors calculated health indicators to assess the population health and argue their importance. Mortality and subjective data on self-perceived health and self-rated morbidity from the Household Budget Survey was used for constructing period morbidity-mortality tables. Thus, the authors applied Sullivan’s method to calculate the life expectancy in very good/good/fair health and the life expectancy without chronic morbidity for the period 2006 - 2015. The life expectancies in very good/good/fair health showed a compression of morbidity in the older ages for both sexes, and for rural and urban types of residence. The life expectancies without chronic morbidity for males and for urban dwellers demonstrated an expansion of morbidity. Although the life expectancy is slowly increasing, the trends in population health are contradictory, depending on the applied measures. The health expectancy indicators, based on self-perceived health, depict the actual situation in the population health. These indicators are becoming more essential with the ageing process and can be used for the tailoring of social and health policies and services to the real needs of the population.

  12. Health and safety in clinical laboratories in developing countries: safety considerations.

    Science.gov (United States)

    Ejilemele, A A; Ojule, A C

    2004-01-01

    Clinical laboratories are potentially hazardous work areas. Health and safety in clinical laboratories is becoming an increasingly important subject as a result of the emergence of highly infectious diseases such as hepatitis and HIV. This is even more so in developing countries where health and safety have traditionally been regarded as low priority issues, considering the more important health problems confronting the health authorities in these countries. We conducted a literature search using the medical subheadings titles on the INTERNET over a period of twenty years and summarized our findings. This article identifies hazards in the laboratories and highlights measures to make the laboratory a safer work place. It also emphasizes the mandatory obligations of employers and employees towards the attainment of acceptable safety standards in clinical laboratories in Third World countries in the face of the current HIV/AIDS epidemic in many of these developing countries especially in the sub-Saharan Africa while accommodating the increasing work load in these laboratories. Both the employer and the employee have major roles to play in the maintenance of a safe working environment. This can be achieved if measures discussed are incorporated into everyday laboratory practice.

  13. Physics measurements and health education

    OpenAIRE

    HAJDUCH, Petr

    2016-01-01

    The thesis "Physical measurements and health education" looks at physical quantities that are related to human health and can be measured in a elementary school environment. It focuses especially on the cross-curricular relationship between physics and health education and also on the use of relevant online measurement systems. As part of this thesis, we suggest a number of activities that exploit this relationship.

  14. 78 FR 64504 - Safety and Occupational Health Study Section (SOHSS), National Institute for Occupational Safety...

    Science.gov (United States)

    2013-10-29

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention Safety and Occupational Health Study Section (SOHSS), National Institute for Occupational Safety and Health (NIOSH or..., Number 177, Pages 56235-56236. Contact Person for More Information: Price Connor, Ph.D., NIOSH Health...

  15. Health and safety education for joint occupational health and safety committees

    Directory of Open Access Journals (Sweden)

    Myriam Mahecha Angulo

    2015-09-01

    Full Text Available Objective: To build a proposal to develop the educational process in health and safety joint committees aimed at safety and health at work (copasst. Methodology: Qualitative, descriptive study in which an in-depth interview to 32 copasst assets was made. Each interview was transcribed and interpreted by applying check with participants, finding meaningful statements, organizing groups of subjects, exhaustive description and validation with participants. The information was placed in the categories planning, organization, development, evaluation and feedback, emerging the following categories: responsible for processes management; planning, place and frequency of educational sessions; topics; format of sessions; involving/ development of sessions; understanding of the issues; applicability to daily life and work environment; applicability to personal/professional life and to the organization. Results: From emerging categories and according to the conceptual framework on adult health education and health and safety for workers, a participatory methodology for the development of educational processes with copasst was built. Conclusions: According to the statement by the members of the copasst, educational processes in health and safety, as they are developed at present, preclude them from achieving necessary competences to perform its functions, thus they are irrelevant.

  16. IAEA publishes first health and safety manual

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1959-01-15

    A 'Manual on the Safe Handling of Radioisotopes' was published in English on 15 Dec ember 1958 by the International Atomic Energy Agency. This is a comprehensive handbook of internationally compiled recommendations for users of radioisotopes. It covers organizational, medical and technical aspects of radiation safety practices. It is also the Agency's first technical publication. French, Russian and Spanish editions will appear shortly. The Manual should prove useful to all users of radioisotopes in industry, medicine, research, etc., but is directed mainly to small scale users who may not have access to other sources of information. The recommendations apply only to radioactivity surpassing the limit of 0,002 microcurie concentration per gram of material; or a total activity of more than 0,1 microcuries in the working areas; this limit is based on the most dangerous radioisotopes. The experts state that the limiting level might be higher for less dangerous isotopes, but recommend that all be treated as potentially dangerous. This would have educational value and avoid accidents caused by misidentification. The Manual also stressed that good radiation safety practices depend on effective organization and warns that even very competent workers sometimes ignore or forget important health and safety requirements.

  17. IAEA publishes first health and safety manual

    International Nuclear Information System (INIS)

    1959-01-01

    A 'Manual on the Safe Handling of Radioisotopes' was published in English on 15 Dec ember 1958 by the International Atomic Energy Agency. This is a comprehensive handbook of internationally compiled recommendations for users of radioisotopes. It covers organizational, medical and technical aspects of radiation safety practices. It is also the Agency's first technical publication. French, Russian and Spanish editions will appear shortly. The Manual should prove useful to all users of radioisotopes in industry, medicine, research, etc., but is directed mainly to small scale users who may not have access to other sources of information. The recommendations apply only to radioactivity surpassing the limit of 0,002 microcurie concentration per gram of material; or a total activity of more than 0,1 microcuries in the working areas; this limit is based on the most dangerous radioisotopes. The experts state that the limiting level might be higher for less dangerous isotopes, but recommend that all be treated as potentially dangerous. This would have educational value and avoid accidents caused by misidentification. The Manual also stressed that good radiation safety practices depend on effective organization and warns that even very competent workers sometimes ignore or forget important health and safety requirements

  18. Coal Mine Health and Safety Regulation 2006 under the Coal Mine Health and Safety Act 2002

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2006-12-22

    The aim of the Act is to secure the health, safety and welfare of people in connection with coal operations (which include all places of work where coal is mined and certain other places). The Regulation contains provisions about the following matters: (a) places of work to which the Act does not apply, (b) duties relating to health, welfare and safety at coal operations, including the following: (i) the nomination of the operator of a coal operation and the provision of health and safety information for incoming operators, (ii) the contents of health and safety management systems for coal operations, (iii) major hazards and the contents of major hazard management plans for coal operations, (iv) duties relating to contractors, (v) the contents of management structures and emergency management systems for coal operations, escape and rescue plans and fire fighting plans and high risk activities, (c) notifications, including (i) notification of incidents, (ii) inquiries, (iii) notification of other matters to the Chief Inspector), (d) aspects of safety at coal operations, including the following: (i) controlled materials, plants and practices, (ii) coal dust explosion prevention and suppression, (iii) ventilation at coal operations, (iv) escape from coal operations, (v) the operation of transport at coal operations, (vi) surveys and certified plans, (vii) employment at coal operations, (e) the licensing of certain activities, (f) competence standards, (g) the Coal Competence Board, (h) check inspectors, (i) exemptions from provisions of this Regulation, (j) the following miscellaneous matters concerning coal mine health and safety: (i) the keeping of records and reporting, (ii) penalties, the review of decisions by the Administrative Decisions Tribunal, fees and charges, consultation, information and other miscellaneous matters, (k) savings and transitional provisions.

  19. Measuring name system health

    NARCIS (Netherlands)

    Casalicchio, Emiliano; Caselli, Marco; Coletta, Alessio; Di Blasi, Salvatore; Fovino, Igor Nai; Butts, Jonathan; Shenoi, Sujeet

    2012-01-01

    Modern critical infrastructure assets are exposed to security threats arising from their use of IP networks and the Domain Name System (DNS). This paper focuses on the health of DNS. Indeed, due to the increased reliance on the Internet, the degradation of DNS could have significant consequences for

  20. Safety and health in boatbuilding and repair.

    Science.gov (United States)

    Brigham, C R; Landrigan, P J

    1985-01-01

    Boatbuilding is a complex, chemically intensive industry which employs approximately 43,000 workers in the United States, 77% of them in shops with fewer than 20 workers. Boatbuilders and repairers are at high risk of occupational injury from falls, lacerations, low back trauma, repetitive motion, noise, burns, fires, and explosions. Also they are at risk of acute and chronic illness, including dermatitis, toxic hepatitis, peripheral neuropathy, and chronic encephalopathy as a result of their occupational exposures to such materials as styrene, resins, solvents, paints, welding fumes, and coating systems. Boatbuilders also are exposed to toxic woods and to lead. Hazard recognition is the first step toward reduction of injury and disease in boat building. Control of recognized hazards is achieved through engineering controls, ventilation in particular, and through medical surveillance. Strong programs for injury prevention and for health and safety education will produce significant health and economic benefit in the boatbuilding industry.

  1. Emerging issues in occupational safety and health.

    Science.gov (United States)

    Schulte, Paul A

    2006-01-01

    In developed countries, changes in the nature of work and the workforce may necessitate recalibrating the vision of occupational safety and health (OSH) researchers, practitioners, and policymakers to increase the focus on the most important issues. New methods of organizing the workplace, extensive labor contracting, expansion of service and knowledge sectors, increase in small business, aging and immigrant workers, and the continued existence of traditional hazards in high-risk sectors such as construction, mining, agriculture, health care, and transportation support the need to address: 1) broader consideration of the role and impact of work, 2) relationship between work and psychological dysfunction, 3) increased surveillance basis for research and intervention, 4) overcoming barriers to the conduct and use of epidemiologic research, 5) information and knowledge transfer and application, 6) economic issues in prevention, and 7) the global interconnectedness of OSH. These issues are offered to spur thinking as new national research agendas for OSH are considered for developed countries.

  2. Integrating Occupational Health and Safety into TAFE Courses: Curriculum Topics.

    Science.gov (United States)

    Hall, Bob; Mageean, Pauline

    This guide is designed to help technical and further education (TAFE) curriculum writers in Australia integrate safety education into vocational education courses. It provides a general overview of occupational health and safety from the perspective of TAFE trade training and a brief summary of the major health and safety issues that might be…

  3. OSHA Training Programs. Module SH-48. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on OSHA (Occupational Safety and Health Act) training programs is one of 50 modules concerned with job safety and health. This module provides a list of OSHA training requirements and describes OSHA training programs and other safety organizations' programs. Following the introduction, 11 objectives (each keyed to a page in the…

  4. Directory of Academic Programs in Occupational Safety and Health.

    Science.gov (United States)

    Weis, William J., III; And Others

    This booklet describes academic program offerings in American colleges and universities in the area of occupational safety and health. Programs are divided into five major categories, corresponding to each of the core disciplines: (1) occupational safety and health/industrial hygiene, (2) occupational safety, (3) industrial hygiene, (4)…

  5. Occupational Safety and Health Programs in Career Education.

    Science.gov (United States)

    DiCarlo, Robert D.; And Others

    This resource guide was developed in response to the Occupational Safety and Health Act of 1970 and is intended to assist teachers in implementing courses in occupational safety and health as part of a career education program. The material is a synthesis of films, programed instruction, slides and narration, case studies, safety pamphlets,…

  6. The Occupational Safety and Health Act: Implications for School Administration.

    Science.gov (United States)

    Licht, Kenneth F.

    The Occupational Safety and Health Act (1970) concerns private schools but does not directly affect the operations of public schools or colleges. The intent, however, is to have the States develop and administer their own health and safety programs. Administrators should, therefore, initiate a comprehensive, districtwide safety education and…

  7. Environment, safety and health progress assessment manual

    International Nuclear Information System (INIS)

    1992-12-01

    On June 27, 1989, the Secretary of Energy announced a 10-Point Initiative to strengthen environment, safety, and health (ES ampersand H) programs, and waste management activities at DOE production, research, and testing facilities. One of the points involved conducting dent Tiger Team Assessments of DOE operating facilities. The Office of Special independent Projects (OSP), EH-5, in the Office of the Assistant Secretary for Environment, Safety and Health, EH-1, was assigned the responsibility to conduct the Tiger Team Assessments. Through June 1992, a total of 35 Tiger Team Assessments were completed. The Secretary directed that Corrective Action Plans be developed and implemented to address the concerns identified by the Tiger Teams. In March 1991, the Secretary approved a plan for assessments that are ''more focused, concentrating on ES ampersand H management, ES ampersand H corrective actions, self-assessment programs, and root-cause related issues.'' In July 1991, the Secretary approved the initiation of ES ampersand H Progress Assessments, as a followup to the Tiger Team Assessments, and in the continuing effort to institutionalize the self-assessment process and line management accountability in the ES ampersand H areas. This manual documents the processes to be used to perform the ES ampersand H Progress Assessments. It was developed based upon the lessons learned from Tiger Team Assessments, the two pilot Progress Assessments, and Progress Assessments that have been completed. The manual will be updated periodically to reflect lessons learned or changes in policy

  8. Occupational health and safety in Brazil.

    Science.gov (United States)

    Frumkin, H; Câmara, V de M

    1991-12-01

    Brazil is the world's fifth largest and sixth most populous nation. Its economy is varied, with strong manufacturing, agriculture, mining, and service sectors. Therefore, a wide variety of workplace hazards confronts its work force. This paper describes Brazil's occupational safety and health regulatory scheme, workers' compensation system, plant-level practices, training, and data collection. We reviewed and analyzed Brazilian regulatory legislation and government and non-governmental organization (NGO) activity in occupational safety and health, as well as the structure and function of the workers' compensation system. We also reviewed available data on injuries and diseases from major sources, including the now-defunct Instituto Nacional do Previdencia Social (INPS) and the workers' compensation scheme, Seguro de Acidente de Trabalho (SAT). The incidence of workplace injuries has decreased in recent years and is now reported to be about 5 per 100 workers per year. The case fatality rate has been constant at about 5 fatalities per 1000 injuries. Less than 6% of reported injuries are classified as "diseases." Brazil's rates are comparable to those of Mexico and Zimbabwe, and two to four times higher than in most industrialized countries. Brazil has a high incidence of occupational injuries and diseases; these injuries and diseases are underreported; there is a large informal sector at special risk; and Brazil illustrates the disparity that exists in many countries between legislation on the books and legislation that is actually implemented.

  9. 78 FR 21977 - Maritime Advisory Committee for Occupational Safety and Health (MACOSH)

    Science.gov (United States)

    2013-04-12

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration Maritime Advisory Committee for Occupational Safety and Health (MACOSH) AGENCY: Occupational Safety and Health Administration (OSHA), Labor... Maritime Advisory Committee for Occupational Safety and Health. The Committee will better enable OSHA to...

  10. 75 FR 35090 - Maritime Advisory Committee for Occupational Safety and Health (MACOSH)

    Science.gov (United States)

    2010-06-21

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration Maritime Advisory Committee for Occupational Safety and Health (MACOSH) AGENCY: Occupational Safety and Health Administration (OSHA), Labor... for Occupational Safety and Health (MACOSH or Committee) was established under Section 7 of the...

  11. Modelling the effects of road traffic safety measures.

    Science.gov (United States)

    Lu, Meng

    2006-05-01

    A model is presented for assessing the effects of traffic safety measures, based on a breakdown of the process in underlying components of traffic safety (risk and consequence), and five (speed and conflict related) variables that influence these components, and are influenced by traffic safety measures. The relationships between measures, variables and components are modelled as coefficients. The focus is on probabilities rather than historical statistics, although in practice statistics may be needed to find values for the coefficients. The model may in general contribute to improve insight in the mechanisms between traffic safety measures and their safety effects. More specifically it allows comparative analysis of different types of measures by defining an effectiveness index, based on the coefficients. This index can be used to estimate absolute effects of advanced driver assistance systems (ADAS) related measures from absolute effects of substitutional (in terms of safety effects) infrastructure measures.

  12. Health and safety at the Whiteshell Nuclear Research Establishment

    International Nuclear Information System (INIS)

    LeNeveu, D.M.

    1982-04-01

    This report outlines the health and safety program at the Whiteshell Nuclear Research Establishment. It describes the procedures in place to ensure that a high standard of conventional industrial and radiation safety is maintained in the workplace

  13. Occupational Safety and Health Act: A Responsibility for Science Teachers

    Science.gov (United States)

    Science Teacher, 1974

    1974-01-01

    Presents implications of the Occupational Safety and Health Act for science teachers both as workers and as they encourage, in students, the development of positive safety attitudes for future occupations. (PEB)

  14. Integrated environment, safety, and health management system description

    International Nuclear Information System (INIS)

    Zoghbi, J. G.

    2000-01-01

    The Integrated Environment, Safety, and Health Management System Description that is presented in this document describes the approach and management systems used to address integrated safety management within the Richland Environmental Restoration Project

  15. Applied Health Physics and Safety annual report for 1975

    International Nuclear Information System (INIS)

    1976-08-01

    This report describes and summarizes the activities of the applied sections and/or groups of the Health Physics Division. Projects and activities covered include personnel monitoring, environmental monitoring, radiation and safety surveys, and industrial safety

  16. Measuring and managing safety at Wahleach Dam

    International Nuclear Information System (INIS)

    Salmon, G. M.; Cattanach, J. D.; Hartford, D. N. D.

    1996-01-01

    Safety improvements recently implemented at the Wahleach Dam were described as one of the first instances in international dam safety practice where risk concepts have been used in conjunction with acceptable risk criteria to evaluate safety of a dam relative to required level of safety. Erosion was identified as the greatest threat to the safety of the dam. In addressing the deficiencies B.C. Hydro formulated a process which advocates a balanced level of safety,i.e. the probability of failure multiplied by the consequences of failure, integrated over a range of initiators. If the risk posed by the dam is lower than a 'tolerable' risk, the dam is considered to be safe enough. In the case of the Wahleach Dam, the inflow design flood (IDF) was selected to be about one half of the probable maximum flow (PMF), hence it was more likely than not that the spillway could pass floods up to and including the PMF. By accepting the determined level of risk, expenditures of several million dollars for design and construction of dam safety improvements were made redundant. Another byproduct of this new concept of risk assessment was the establishment of improved life safety protection by means of an early warning system for severe floods through the downstream community and emergency authorities. 3 refs., 5 tabs

  17. Occupational safety and health textbook for radiological personnel employed in structural material testing

    International Nuclear Information System (INIS)

    Abraham, J.

    1981-01-01

    The comprehensive textbook for X-ray and radiological testing personnel includes requirements and rules of occupational safety and health on the basis of Hungarian and international (mainly German) literature. In the chapter Fundamentals, X-ray and radioactive radiations, their measurements and biological effects, doses etc are described. In the chapter Occupational safety and health, the jobs representing radiation hazards are listed and safety regulations for them are reported. Finally, information for prevention and first aid is presented. Control questions are added to each part. The Appendix contains safety standards and regulations, information on legal aspects of safety and radiation protection as well as recommendations. (Sz.J.)

  18. Reducing health care hazards: lessons from the commercial aviation safety team.

    Science.gov (United States)

    Pronovost, Peter J; Goeschel, Christine A; Olsen, Kyle L; Pham, Julius C; Miller, Marlene R; Berenholtz, Sean M; Sexton, J Bryan; Marsteller, Jill A; Morlock, Laura L; Wu, Albert W; Loeb, Jerod M; Clancy, Carolyn M

    2009-01-01

    The movement to improve quality of care and patient safety has grown, but examples of measurable and sustained progress are rare. The slow progress made in health care contrasts with the success of aviation safety. After a tragic 1995 plane crash, the aviation industry and government created the Commercial Aviation Safety Team to reduce fatal accidents. This public-private partnership of safety officials and technical experts is responsible for the decreased average rate of fatal aviation accidents. We propose a similar partnership in the health care community to coordinate national efforts and move patient safety and quality forward.

  19. Safety and Health Division achievements during 40 years

    International Nuclear Information System (INIS)

    Noriah Mod Ali

    2012-01-01

    During her speech, presenter outlined several issues regarding on establishment of Safety and Health Division since 40 years. This division contain of 3 sub unit; Physical Safety Group, Medical Physic Group and Non-ionizing Radiation group (NIR). The objectives of this division to implement R and D activities and services regarding safety and radiological health also non-radiological to ensure public safety, environment and asset suit with obligations established by authorities, IAEA standards and regulations.(author)

  20. Barsebaeck power plant - safety and emergency measures

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    A Swedish-Danish Committee on safety at the Swedish nuclear power plant Barsebaeck was established in 1979 in order to evaluate the nuclear safety at Barsebaeck with a view to the reactor accident at the Three-Mile-Island nuclear power plant March 28, 1979. According to the committees mandate the investigations of the Kemeny Commission, the Rogouin investigation, investigations of the American Nuclear Regulatory Commission, and the Swedish report ''Safe nuclear power'' have been taken into consideration by the Committee. Furthermore, it has formed the basis for the Committees work that the authority responsibility for the safety at Barsebaeck lies with the Swedish authorities, and that these authorities have evaluated the safety aspects before the permissions for operation of the Barsebaeck power plant were given and hereafter currently in connection with the inspection of the power plant. The report prepared by the Commission treats aspects as: a) Nuclear safety at the Barsebaeck power plant, b) reactor safety and emergency provisions, c) common elements in the emergency provision situation in Sweden and Denmark, d) ongoing investigations on course of events during accidents and release limiting safety systems. (BP)

  1. The labor protection and safety measures at the electrolysis department

    International Nuclear Information System (INIS)

    Galushkin, N.V.

    1995-01-01

    This chapter of monograph is devoted to labor protection and safety measures at the electrolysis department. Thus, the characteristics of dangerous and harmful production factors as well as the danger of thermal burns and thermal exposure were considered. Safety requirements on labor safety were studied.

  2. Stennis Space Center observes 2009 Safety and Health Day

    Science.gov (United States)

    2009-01-01

    Sue Smith, a medical clinic employee at NASA's John C. Stennis Space Center, takes the temperature of colleague Karen Badon during 2009 Safety and Health Day activities Oct. 22. Safety Day activities included speakers, informational sessions and a number of displays on safety and health issues. Astronaut Dominic Gorie also visited the south Mississippi rocket engine testing facility during the day to address employees and present several Silver Snoopy awards for outstanding contributions to flight safety and mission success. The activities were part of an ongoing safety and health emphasis at Stennis.

  3. Teaching Safety and Health in the Workplace. An Instructor's Guide.

    Science.gov (United States)

    Occupational Safety and Health Administration, Washington, DC.

    The primary concern of the Occupational Safety and Health Act (OSHA) is to provide a safe and healthful workplace for every working man and woman in the nation. One way to help reduce the number of injuries and illnesses in the workplace is by training workers to be more aware of the job safety and health hazards and to teach them the methods of…

  4. 21 CFR 25.16 - Public health and safety emergencies.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Public health and safety emergencies. 25.16... ENVIRONMENTAL IMPACT CONSIDERATIONS Agency Actions Requiring Environmental Consideration § 25.16 Public health... importance to the public health or safety, may make full adherence to the procedural provisions of NEPA and...

  5. The President's Report on Occupational Safety and Health.

    Science.gov (United States)

    Department of Health, Education, and Welfare, Washington, DC.

    This report describes what has been done to implement the Occupational Safety and Health Act of 1970 during its first year of operation. The report examines the responsibilities of the Department of Labor for setting safety and health standards and also explores the activities of the Department of Health, Education, and Welfare in research and…

  6. Gender issues on occupational safety and health.

    Science.gov (United States)

    Sorrentino, Eugenio; Vona, Rosa; Monterosso, Davide; Giammarioli, Anna Maria

    2016-01-01

    The increasing proportion of women in the workforce raises a range of gender-related questions about the different effects of work-related risks on men and women. Few studies have characterized gender differences across occupations and industries, although at this time, the gender sensitive approach is starting to acquire relevance in the field of human preventive medicine. The European Agency for Safety and Health at Work has encouraged a policy of gender equality in all European member states. Italy has adopted European provisions with new specific legislation that integrates the previous laws and introduces the gender differences into the workplace. Despite the fact that gender equal legislation opportunities have been enacted in Italy, their application is delayed by some difficulties. This review examines some of these critical aspects.

  7. Evaluation of fire safety measures at local universities in Kenya with ...

    African Journals Online (AJOL)

    This study establishes fire safety measures in place in local universities in Kenya, and ... fire suppression systems, fire detection and alarm systems and fire Hydrants. ... response backed by university management endorsement and support. The Directorate of occupational safety and health services should also make the ...

  8. Nanomaterials: new challenges in environmental health and safety

    International Nuclear Information System (INIS)

    Sun, Casper; Gallaghar, Robert G.

    2008-01-01

    A follow-up of the Nano-panel discussion in the 41 st Midyear Health Physics Society (HPS) meeting, Oakland CA, 'Accelerators and Nanoparticles' have been introduced to and discussed among participants, i.e., health physicists, especially within the topic that monitoring and measurement of nano-radioactive materials. It is documented clearly that the chemistry and physical mobility and optical properties, and the monitoring and protection requirements for nano-radioactive substances vary observed from collective experiences. Soon after nanocarbon-tube discovery and use of the innovated materials expand, as nanoscience and nanotechnogy, exponential globally and revolutionized in just about every industries, for examples, agricultural, chemical, biological, pharmaceutical, medical, electronic, green-energies. To produce individual desired benefits, the engineered tiny substances could add health risk inevitably to the workers and consumers. The environmental health and safety (EH and S) research budgets and awareness programs have been steady increased in according with National Nanotechnology Initiative (NNI) report. All nanoscale materials which they have virtually invisible and yet can penetrate and deposit on cell walls of living organs and tissues without being detected once inhaled or ingested in the body, the handling and application of these materials with associated hazard in terms of occupational and environment risk must be identified, investigated, and documented before any of damage or vulnerability revealed. In the other words, be prepared then sorry. Many common properties and risk issues are identical or very similar between radioactive and nanoscale materials. Both are exist naturally and will persist. What is and is not a problem, must be clearly understood to support operational and protection decision making. The safety data must be provided in Internet transparently and voluntarily. All nanomaterials should consider as hazard before proofed. The

  9. Hawaii State Plan for Occupational Safety and Health. Final rule.

    Science.gov (United States)

    2012-09-21

    This document announces the Occupational Safety and Health Administration's (OSHA) decision to modify the Hawaii State Plan's ``final approval'' determination under Section 18(e) of the Occupational Safety and Health Act (the Act) and to transition to ``initial approval'' status. OSHA is reinstating concurrent federal enforcement authority over occupational safety and health issues in the private sector, which have been solely covered by the Hawaii State Plan since 1984.

  10. Design of an indicator for health and safety governance

    OpenAIRE

    Minguillón, Roberto F.; Yacuzzi, Enrique

    2009-01-01

    Occupational Health and Safety Governance (OHSG) is a branch of Corporate Governance by which the board directs and controls labor risks created by their own enterprise. The OHSG concept is relatively new; unlike Occupational Health and Safety Management, which is mostly related to the work of managerial ranks, OHSG deals with principles, the interests of stakeholders, and the work of directors. The paper defines the new concept, OHSG, develops an original health and safety indicator, and pre...

  11. Health, safety and environment : annual report 2000

    International Nuclear Information System (INIS)

    2000-01-01

    A natural gas transmission and power services company, TransCanada Pipelines Limited operates approximately 38,000 kilometers of pipeline, thereby supplying the majority of natural gas production facilities in Western Canada. The company is also involved in the power generation industry by building, operating and owning interests in electric power plants. Located in Rhode Island, United States, the largest plant operated by TransCanada is a combined-cycle plant that generates in excess of 500 MW. TransCanada is committed to its health, safety and environment management system. The system is modeled after the elements of the International Organization for Standardization (ISO) 14001 which sets the standard for environmental management systems. Considerable efforts were expanded to implement programs and initiatives to protect the environment, such as the pipeline reclamation criteria, the hazardous materials and waste management, and proposed polychlorinated biphenyl (PCB) regulations, which are currently under consideration by Environment Canada. TransCanada PipeLines Limited has also set up an environmental research program to enable management and workers to minimize the environmental impacts of the business. Its objectives are the enhancement of the health and safety of employees and their communities, the mitigation of effects on lands, air and water. The topics covered by the research are: vegetation and wildlife with several sub-categories. The company is concerned about the effects on climate change, and developed plans and strategies to manage the emissions of greenhouse gases. In the process, it was awarded several awards for its commitment, action and leadership on voluntary reduction program of greenhouse gases. Full-time resources are dedicated to illness prevention and health promotion, employee assistance programs, short and long term disability management and others. During the year 2000, TransCanada invested 4 million dollars in communities

  12. Multidisciplinary training program to create new breed of radiation monitor: the health and safety technician

    International Nuclear Information System (INIS)

    Vance, W.F.

    1979-01-01

    A multidiscipline training program established to create a new monitor, theHealth and Safety Technician, is described. The training program includes instruction in fire safety, explosives safety, industrial hygiene, industrial safety, health physics, and general safety practices

  13. [Mental Health: Concepts, Measures, Determinants].

    Science.gov (United States)

    Doré, Isabelle; Caron, Jean

    Objectives This article aims to situate the concept of mental health in a historical perspective. This article presents the most commonly used measurement tools in Canada and elsewhere in the world to assess specific and multiple dimensions of mental health; when available, psychometric properties are discussed. Finally, research findings on quality of life and mental health determinants are presented.Methods A literature review of concepts, measurement and determinants of mental health is presented in this paper. The selection of measurement scales presented is based on the findings of the research reports conducted by the second author, an expert on mental health measures, for Health Canada and Statistics Canada.Results Mental health is more than the absence of mental illness; rather it is a state of complete well-being, which refers to our ability to enjoy life and deal with the challenges we face. Accordingly, mental health and mental illness are not extremes of the same continuum, but distinct yet correlated concepts. The traditional conceptualization suggesting that mental health represents simply the absence of mental illness has been replaced, in the last few decades, by a more holistic characterization, which directly concerns public health. The components of mental health include emotional well-being/quality of life (QOL) and psychological and social well-being. Mental health influences the personal and social functioning of individuals, justifying the importance of intervening upstream to promote mental health. Specific scales are relevant for obtaining a detailed measure of one aspect of well-being in particular (emotional/quality of life, psychological or social well-being); however, to account for the global mental health status, measurement tools that integrate all three forms of well-being (emotional, psychological and social) should be privileged. A diversity of determinants at the individual, social and neighbourhood levels influence quality of

  14. Anthropology in Agricultural Health and Safety Research and Intervention.

    Science.gov (United States)

    Arcury, Thomas

    2017-01-01

    Agriculture remains a dangerous industry, even as agricultural science and technology continue to advance. Research that goes beyond technological changes to address safety culture and policy are needed to improve health and safety in agriculture. In this commentary, I consider the potential for anthropology to contribute to agricultural health and safety research by addressing three aims: (1) I briefly consider what the articles in this issue of the Journal of Agromedicine say about anthropologists in agricultural health and safety; (2) I discuss what anthropologists can add to agricultural health and safety research; and (3) I examine ways in which anthropologists can participate in agricultural health and safety research. In using their traditions of rigorous field research to understand how those working in agriculture perceive and interpret factors affecting occupational health and safety (their "emic" perspective), and translating this perspective to improve the understanding of occupational health professionals and policy makers (an "etic" perspective), anthropologists can expose myths that limit improvements in agricultural health and safety. Addressing significant questions, working with the most vulnerable agricultural communities, and being outside establishment agriculture provide anthropologists with the opportunity to improve health and safety policy and regulation in agriculture.

  15. University building safety index measurement using risk and implementation matrix

    Science.gov (United States)

    Rahman, A.; Arumsari, F.; Maryani, A.

    2018-04-01

    Many high rise building constructed in several universities in Indonesia. The high-rise building management must provide the safety planning and proper safety equipment in each part of the building. Unfortunately, most of the university in Indonesia have not been applying safety policy yet and less awareness on treating safety facilities. Several fire accidents in university showed that some significant risk should be managed by the building management. This research developed a framework for measuring the high rise building safety index in university The framework is not only assessed the risk magnitude but also designed modular building safety checklist for measuring the safety implementation level. The safety checklist has been developed for 8 types of the university rooms, i.e.: office, classroom, 4 type of laboratories, canteen, and library. University building safety index determined using risk-implementation matrix by measuring the risk magnitude and assessing the safety implementation level. Building Safety Index measurement has been applied in 4 high rise buildings in ITS Campus. The building assessment showed that the rectorate building in secure condition and chemical department building in beware condition. While the library and administration center building was in less secure condition.

  16. A health and safety primer for the practicing health physicist

    International Nuclear Information System (INIS)

    Hylko, J.M.; Bradshaw, M.C.; Ross, L.E.; Brennan, M.J.; Pomatto, C.B.; Shelly, F.C.

    1996-01-01

    Environmental restoration (ER) is the process of removing a facility from service, the demolition of structures the identification and disposal of all hazardous and radioactive wastes, the decontamination of equipment and materials, and the restoration of a site for unrestricted use. The number of ER projects encompassing hazardous, industrial, and radiological conditions is expected to increase in response to various program requirements or mission changes. As a result, the practicing health physicist (HP) may have to address unique health and safety (H and S) issues beyond those of performing routine radiological activities. These unique H and S issues could include, but are not limited to the razing of buildings, the removal of radioactive materials and hazardous chemicals, below-grade excavation, confined space entry, storing flammable or combustible liquids, monitoring exposure to hazardous substances, contacting energized systems (e.g., electricity, hydraulics), noise abatement, the nullification of manufacturer warranties, and the operation and movement of heavy equipment. The purpose of this paper is to educate the practicing HP about these issues by reviewing specific regulations governing all H and S activities, and to provide an example of a site-specific H and S primer (e.g., Health and Safety Plan [HASP]). This primer advices the practicing HP about sound H and S principles, furnishes basic strategies for performing a hazard assessment/job safety analysis (HA/JSA) that can be applied to any ER project, and describes various engineering and administrative controls to mitigate hazardous exposures to ER personnel. In addition, 26 inspection checklist topics are available from the primary author to evaluate the adequacy of the engineering and administrative controls, or to necessitate the use of personal protective equipment (PPE) thereby mitigating the corresponding hazard. (author)

  17. Studying the Safety Impact of Autonomous Vehicles Using Simulation-Based Surrogate Safety Measures

    OpenAIRE

    Morando, Mark Mario; Tian, Qingyun; Truong, Long T.; Vu, Hai L.

    2018-01-01

    Autonomous vehicle (AV) technology has advanced rapidly in recent years with some automated features already available in vehicles on the market. AVs are expected to reduce traffic crashes as the majority of crashes are related to driver errors, fatigue, alcohol, or drugs. However, very little research has been conducted to estimate the safety impact of AVs. This paper aims to investigate the safety impacts of AVs using a simulation-based surrogate safety measure approach. To this end, safety...

  18. Problems in determining the optimal use of road safety measures

    DEFF Research Database (Denmark)

    Elvik, Rune

    2014-01-01

    for intervention that ensures maximum safety benefits. The third problem is how to develop policy options to minimise the risk of indivisibilities and irreversible choices. The fourth problem is how to account for interaction effects between road safety measures when determining their optimal use. The fifth......This paper discusses some problems in determining the optimal use of road safety measures. The first of these problems is how best to define the baseline option, i.e. what will happen if no new safety measures are introduced. The second problem concerns choice of a method for selection of targets...... problem is how to obtain the best mix of short-term and long-term measures in a safety programme. The sixth problem is how fixed parameters for analysis, including the monetary valuation of road safety, influence the results of analyses. It is concluded that it is at present not possible to determine...

  19. 76 FR 32374 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2011-06-06

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2011-0065] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... on Occupational Safety and Health (NACOSH) and NACOSH subgroups. SUMMARY: The National Advisory...

  20. 75 FR 28659 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2010-05-21

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2010-0012] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... on Occupational Safety and Health (NACOSH). SUMMARY: The National Advisory Committee on Occupational...

  1. 75 FR 2890 - OSHA Listens: Occupational Safety and Health Administration Stakeholder Meeting

    Science.gov (United States)

    2010-01-19

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2010-0004] OSHA Listens: Occupational Safety and Health Administration Stakeholder Meeting AGENCY: Occupational Safety and Health Administration (OSHA), Labor. ACTION: Notice of public meeting. SUMMARY: The Occupational Safety...

  2. 75 FR 78775 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2010-12-16

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2010-0012] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... on Occupational Safety and Health (NACOSH) and NACOSH subgroup meetings. SUMMARY: The National...

  3. Health-physics Measurements: Services

    International Nuclear Information System (INIS)

    Hardeman, F.; Hurtgen, C.; Vanhavere, F.; Vanmarcke, H.

    1998-01-01

    SCK-CEN's programme on health-physics (1) offers complete services in health-physics measurements according to international quality standards; (2) contributes to improve continuously these measurement techniques and follows up international recommendations and legislation concerning the surveillance of workers; (3) provides support and advise to nuclear and non-nuclear industry on issues of radioactive contamination. Progress and achievements in 1997 are summarised

  4. Nuclear health and safety. Status of GAO's environmental, safety, and health recommendations to DOE

    International Nuclear Information System (INIS)

    England-Joseph, Judy; Bannerman, Carl J.; Fenzel, William F.; Brack, David L.; Harter, Frederick A.

    1990-04-01

    DOE's operations are carried out at many contractor-operated sites around the country, including major sites within the nuclear weapons complex that are involved in the production of nuclear material for weapons and naval fuel. At these sites DOE contractors routinely use and generate large quantities of a wide range of hazardous and radioactive materials. Because these materials require special handling by workers. Also pursuant to Mar. 15, 1989, request, we provided you a report entitled Nuclear Health and Safety: Need for Improved Responsiveness to Problems at DOE Sites (GAO/RCED-90-101, Mar. 28, 1990). to prevent exposure to themselves or releases into the environment, DOE's weapons complex, considered in its entirety, is among the potentially more dangerous industrial operations in the world. Over the last decade, at the request of the Congress, we have carried out a series of assessments and evaluations of various aspects of the complex. In over 60 reports and testimonies published since 1990, we have called attention to the mounting problems facing DOE's nuclear weapons complex. This body of work includes (1) identifying serious, costly, and widespread environmental, safety, and health problems at DOE facilities, (2) calling for outside independent oversight of DOE's nuclear operations, and (3) making recommendations to DOE to strengthen its oversight, providing more detailed information and plans to the Congress, and improving its management and accounting practices. In total, our reports and testimonies have included 54 recommendations to DOE, in addition to recommendations to the Congress, concerning environmental, safety, and health matters at the complex. We consider 23 of the 54 recommendations to be still open. The open recommendations call for improvements such as tighter program controls and clearer standards and policies related to environmental, safety, and health matters

  5. Measures to Improve Diagnostic Safety in Clinical Practice.

    Science.gov (United States)

    Singh, Hardeep; Graber, Mark L; Hofer, Timothy P

    2016-10-20

    Timely and accurate diagnosis is foundational to good clinical practice and an essential first step to achieving optimal patient outcomes. However, a recent Institute of Medicine report concluded that most of us will experience at least one diagnostic error in our lifetime. The report argues for efforts to improve the reliability of the diagnostic process through better measurement of diagnostic performance. The diagnostic process is a dynamic team-based activity that involves uncertainty, plays out over time, and requires effective communication and collaboration among multiple clinicians, diagnostic services, and the patient. Thus, it poses special challenges for measurement. In this paper, we discuss how the need to develop measures to improve diagnostic performance could move forward at a time when the scientific foundation needed to inform measurement is still evolving. We highlight challenges and opportunities for developing potential measures of "diagnostic safety" related to clinical diagnostic errors and associated preventable diagnostic harm. In doing so, we propose a starter set of measurement concepts for initial consideration that seem reasonably related to diagnostic safety and call for these to be studied and further refined. This would enable safe diagnosis to become an organizational priority and facilitate quality improvement. Health-care systems should consider measurement and evaluation of diagnostic performance as essential to timely and accurate diagnosis and to the reduction of preventable diagnostic harm.This is an open-access article distributed under the terms of the Creative Commons Attribution-Non Commercial-No Derivatives License 4.0 (CCBY-NC-ND), where it is permissible to download and share the work provided it is properly cited. The work cannot be changed in any way or used commercially without permission from the journal.

  6. 48 CFR 923.7002 - Worker safety and health.

    Science.gov (United States)

    2010-10-01

    ... Information and Protection of Worker Safety and Health” or “952.223-77, Conditional Payment of Fee or Profit—Protection of Worker Safety and Health” implement the requirements of section 234C of the Atomic Energy Act... 48 Federal Acquisition Regulations System 5 2010-10-01 2010-10-01 false Worker safety and health...

  7. Relationship of hospital organizational culture to patient safety climate in the Veterans Health Administration.

    Science.gov (United States)

    Hartmann, Christine W; Meterko, Mark; Rosen, Amy K; Shibei Zhao; Shokeen, Priti; Singer, Sara; Gaba, David M

    2009-06-01

    Improving safety climate could enhance patient safety, yet little evidence exists regarding the relationship between hospital characteristics and safety climate. This study assessed the relationship between hospitals' organizational culture and safety climate in Veterans Health Administration (VA) hospitals nationally. Data were collected from a sample of employees in a stratified random sample of 30 VA hospitals over a 6-month period (response rate = 50%; n = 4,625). The Patient Safety Climate in Healthcare Organizations (PSCHO) and the Zammuto and Krakower surveys were used to measure safety climate and organizational culture, respectively. Higher levels of safety climate were significantly associated with higher levels of group and entrepreneurial cultures, while lower levels of safety climate were associated with higher levels of hierarchical culture. Hospitals could use these results to design specific interventions aimed at improving safety climate.

  8. The occupational safety of health professionals working at community and family health centers.

    Science.gov (United States)

    Ozturk, Havva; Babacan, Elif

    2014-10-01

    Healthcare professionals encounter many medical risks while providing healthcare services to individuals and the community. Thus, occupational safety studies are very important in health care organizations. They involve studies performed to establish legal, technical, and medical measures that must be taken to prevent employees from sustaining physical or mental damage because of work hazards. This study was conducted to determine if the occupational safety of health personnel at community and family health centers (CHC and FHC) has been achieved. The population of this cross-sectional study comprised 507 nurses, 199 physicians, and 237 other medical personnel working at a total of 18 family health centers (FHC) and community health centers (CHC) in Trabzon, Turkey. The sample consisted of a total of 418 nurses, 156 physicians, and 123 other medical personnel. Sampling method was not used, and the researchers tried to reach the whole population. Data were gathered with the Occupational Safety Scale (OSS) and a questionnaire regarding demographic characteristics and occupational safety. According to the evaluations of all the medical personnel, the mean ± SD of total score of the OSS was 3.57 ± 0.98; of the OSS's subscales, the mean ± SD of the health screening and registry systems was 2.76 ± 1.44, of occupational diseases and problems was 3.04 ± 1.3 and critical fields control was 3.12 ± 1.62. In addition, occupational safety was found more insufficient by nurses (F = 14.18; P occupational safety to be insufficient as related to protective and supportive activities.

  9. Health and Safety Research Division progress report, October 1, 1982-June 30, 1984

    International Nuclear Information System (INIS)

    Kaye, S.V.

    1984-08-01

    The work accomplished by the Health and Safety Research Division, Oak Ridge National Laboratory is summarized. Research, assessments and technical measurements done by the division between October 1982 and June 1984 are summarized. Separate analytics were written for each chapter

  10. A model of Occupational Safety and Health Management System (OSHMS) for promoting and controlling health and safety in textile industry.

    Science.gov (United States)

    Manimaran, S; Rajalakshmi, R; Bhagyalakshmi, K

    2015-01-01

    The development of Occupational Safety and Health Management System in textile industry will rejuvenate the workers and energize the economy as a whole. In India, especially in Tamil Nadu, approximately 1371 textile business is running with the help of 38,461 workers under Ginning, Spinning, Weaving, Garment and Dyeing sectors. Textile industry of contributes to the growth of Indian economy but it fails to foster education and health as key components of human development and help new democracies. The present work attempts to measure and develop OSHMS which reduce the hazards and risk involved in textile industry. Among all other industries textile industry is affected by enormous hazards and risk because of negligence by management and Government. It is evident that managements are not abiding by law when an accident has occurred. Managements are easily deceiving workers and least bothered about the Quality of Work Life (QWL). A detailed analysis of factors promoting safety and health to the workers has been done by performing confirmatory factor analysis, evaluating Risk Priority Number and the framework of OHMS has been conceptualized using Structural Equation Model. The data have been collected using questionnaire and interview method. The study finds occupation health for worker in Textile industry is affected not only by safety measure but also by technology and management. The work shows that difficulty in identifying the cause and effect of hazards, the influence of management in controlling and promoting OSHMS under various dimensions. One startling fact is existence of very low and insignificance correlation between health factors and outcome.

  11. Safety Precautions. Child Health and Safety Series (Module I).

    Science.gov (United States)

    Iscoe, Louise; And Others

    This manual for parents and child care personnel in day care homes and centers provides guidelines and information on indoor and outdoor safety precautions, emergency preparation and first aid. Contents focus on monitoring arrivals and departures, prevention of suffocation and strangulation, control of pets and other animals, preventing and…

  12. Linking better shiftwork arrangements with safety and health management systems.

    Science.gov (United States)

    Kogi, Kazutaka

    2004-12-01

    Various support measures useful for promoting joint change approaches to the improvement of both shiftworking arrangements and safety and health management systems were reviewed. A particular focus was placed on enterprise-level risk reduction measures linking working hours and management systems. Voluntary industry-based guidelines on night and shift work for department stores and the chemical, automobile and electrical equipment industries were examined. Survey results that had led to the compilation of practicable measures to be included in these guidelines were also examined. The common support measures were then compared with ergonomic checkpoints for plant maintenance work involving irregular nightshifts. On the basis of this analysis, a new night and shift work checklist was designed. Both the guidelines and the plant maintenance work checkpoints were found to commonly cover multiple issues including work schedules and various job-related risks. This close link between shiftwork arrangements and risk management was important as shiftworkers in these industries considered teamwork and welfare services to be essential for managing risks associated with night and shift work. Four areas found suitable for participatory improvement by managers and workers were work schedules, ergonomic work tasks, work environment and training. The checklist designed to facilitate participatory change processes covered all these areas. The checklist developed to describe feasible workplace actions was suitable for integration with comprehensive safety and health management systems and offered valuable opportunities for improving working time arrangements and job content together.

  13. Supporting Fernald Site Closure with Integrated Health and Safety Plans as Documented Safety Analyses

    International Nuclear Information System (INIS)

    Kohler, S.; Brown, T.; Fisk, P.; Krach, F.; Klein, B.

    2004-01-01

    At the Fernald Closure Project (FCP) near Cincinnati, Ohio, environmental restoration activities are supported by Documented Safety Analyses (DSAs) that combine the required project-specific Health and Safety Plans, Safety Basis Requirements (SBRs), and Process Requirements (PRs) into single Integrated Health and Safety Plans (I-HASPs). These integrated DSAs employ Integrated Safety Management methodology in support of simplified restoration and remediation activities that, so far, have resulted in the decontamination and demolition (D and D) of over 200 structures, including eight major nuclear production plants. There is one of twelve nuclear facilities still remaining (Silos containing uranium ore residues) with its own safety basis documentation. This paper presents the status of the FCP's safety basis documentation program, illustrating that all of the former nuclear facilities and activities have now replaced. Basis of Interim Operations (BIOs) with I-HASPs as their safety basis during the closure process

  14. Safety culture perceptions of pharmacists in Malaysian hospitals and health clinics: a multicentre assessment using the Safety Attitudes Questionnaire

    Science.gov (United States)

    Samsuri, Srima Elina; Pei Lin, Lua; Fahrni, Mathumalar Loganathan

    2015-01-01

    Objective To assess the safety attitudes of pharmacists, provide a profile of their domains of safety attitude and correlate their attitudes with self-reported rates of medication errors. Design A cross-sectional study utilising the Safety Attitudes Questionnaire (SAQ). Setting 3 public hospitals and 27 health clinics. Participants 117 pharmacists. Main outcome measure(s) Safety culture mean scores, variation in scores across working units and between hospitals versus health clinics, predictors of safety culture, and medication errors and their correlation. Results Response rate was 83.6% (117 valid questionnaires returned). Stress recognition (73.0±20.4) and working condition (54.8±17.4) received the highest and lowest mean scores, respectively. Pharmacists exhibited positive attitudes towards: stress recognition (58.1%), job satisfaction (46.2%), teamwork climate (38.5%), safety climate (33.3%), perception of management (29.9%) and working condition (15.4%). With the exception of stress recognition, those who worked in health clinics scored higher than those in hospitals (psafety culture. As perceptions improved, the number of medication errors reported decreased. Group-specific interventions that target specific domains are necessary to improve the safety culture. PMID:26610761

  15. A simple graphical method for measuring inherent safety

    International Nuclear Information System (INIS)

    Gupta, J.P.; Edwards, David W.

    2003-01-01

    Inherently safer design (ISD) concepts have been with us for over two decades since their elaboration by Kletz [Chem. Ind. 9 (1978) 124]. Interest has really taken off globally since the early nineties after several major mishaps occurred during the eighties (Bhopal, Mexico city, Piper-alfa, Philips Petroleum, to name a few). Academic and industrial research personnel have been actively involved into devising inherently safer ways of production. The regulatory bodies have also shown deep interest since ISD makes the production safer and hence their tasks easier. Research funding has also been forthcoming for new developments as well as for demonstration projects. A natural question that arises is as to how to measure ISD characteristics of a process? Several researchers have worked on this [Trans. IChemE, Process Safety Environ. Protect. B 71 (4) (1993) 252; Inherent safety in process plant design, Ph.D. Thesis, VTT Publication Number 384, Helsinki University of Technology, Espoo, Finland, 1999; Proceedings of the Mary Kay O'Connor Process Safety Center Symposium, 2001, p. 509]. Many of the proposed methods are very elegant, yet too involved for easy adoption by the industry which is scared of yet another safety analysis regime. In a recent survey [Trans. IChemE, Process Safety Environ. Prog. B 80 (2002) 115], companies desired a rather simple method to measure ISD. Simplification is also an important characteristic of ISD. It is therefore desirable to have a simple ISD measurement procedure. The ISD measurement procedure proposed in this paper can be used to differentiate between two or more processes for the same end product. The salient steps are: Consider each of the important parameters affecting the safety (e.g., temperature, pressure, toxicity, flammability, etc.) and the range of possible values these parameters can have for all the process routes under consideration for an end product. Plot these values for each step in each process route and compare. No

  16. Curriculum: Integrating Health and Safety Into Engineering Curricula.

    Science.gov (United States)

    Talty, John T.

    1985-01-01

    National Institute for Occupational Safety and Health instituted a project in 1980 to encourage engineering educators to focus on occupational safety and health issues in engineering curricula. Progress to date is outlined, considering specific results in curriculum development, engineering society interaction, and formation of a teaching…

  17. Impact of Construction Health & Safety Regulations on Project ...

    African Journals Online (AJOL)

    Impact of Construction Health & Safety Regulations on Project Parameters in Nigeria: Consultants and Contractors View. ... The study recommends that better attention is given to health and safety should as a project parameter and that related practice notes and guidelines should be evolved for all project stakeholders.

  18. Zagazig Journal of Occupational Health and Safety: Editorial Policies

    African Journals Online (AJOL)

    Focus and Scope. Zagazig Journal of Occupational Health and Safety is aimed at physicians and researchers in the wide-ranging discipline of occupational and ... The main objectives of Zagazig Journal of Occupational Health and Safety are to publish high quality scientific articles , to maximize the citation rate of the ...

  19. Health, safety and environmental issues in thin film manufacturing

    NARCIS (Netherlands)

    Alsema, E.A.; Baumann, A.E.; Hill, R.; Patterson, M.H.

    1997-01-01

    An investigation is made of Health, Safety and Environmental (HSE) aspects for the manufacturing, use and decommissioning of CdTe, CIS and a-Si modules. Issues regarding energy requirements, resource availability, emissions of toxic materials, occupational health and safety and module waste

  20. 77 FR 22358 - Occupational Safety and Health Administration

    Science.gov (United States)

    2012-04-13

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration Preparations for the 23rd Session of the UN Sub-Committee of Experts on the Globally Harmonized System of Classification and...: Occupational Safety and Health Administration (OSHA), Labor. ACTION: Notice of public meeting. SUMMARY: OSHA...

  1. Software for the occupational health and safety integrated management system

    International Nuclear Information System (INIS)

    Vătăsescu, Mihaela

    2015-01-01

    This paper intends to present the design and the production of a software for the Occupational Health and Safety Integrated Management System with the view to a rapid drawing up of the system documents in the field of occupational health and safety

  2. 48 CFR 352.223-70 - Safety and health.

    Science.gov (United States)

    2010-10-01

    ... laboratories; and other applicable occupational health and safety standards issued by OSHA and included in 29... Commission Standards and Regulations, pursuant to the Energy Reorganization Act of 1974 (42 U.S.C. 5801 et... health and safety operating procedures and practices for both personnel and facilities: (i) Biosafety in...

  3. Revised health and safety compliance model for the Ghanaian ...

    African Journals Online (AJOL)

    The construction industry in Ghana is faced with employees' negligence in obeying rules and regulations, and acts that conflict with health and safety. The purpose of the paper was to present the revised health and safety (H&S) compliance model for the construction industry based on a developed theoretical six factor ...

  4. Training Course for Compliance Safety and Health Officers. Final Report.

    Science.gov (United States)

    McKnight, A. James; And Others

    The report describes revision of the Compliance Safety and Health Officers (CSHO) course for the Department of Labor, Occupational Safety and Health Administration (OSHA). The CSHO's job was analyzed in depth, in accord with OSHA standards, policies, and procedures. A listing of over 1,700 violations of OSHA standards was prepared, and specialists…

  5. Software for the occupational health and safety integrated management system

    Energy Technology Data Exchange (ETDEWEB)

    Vătăsescu, Mihaela [University Politehnica Timisoara, Department of Engineering and Management, 5 Revolutiei street, 331128 Hunedoara (Romania)

    2015-03-10

    This paper intends to present the design and the production of a software for the Occupational Health and Safety Integrated Management System with the view to a rapid drawing up of the system documents in the field of occupational health and safety.

  6. Workplace Safety and Health Topics: Industries and Occupations

    Science.gov (United States)

    ... Submit Search The CDC The National Institute for Occupational Safety and Health (NIOSH) Note: Javascript is disabled or is not ... September 6, 2017 Content source: National Institute for Occupational Safety and Health Education and Information Division Email Recommend Tweet YouTube ...

  7. Occupational Safety and Health Practices: An Alarming Call to Action

    Science.gov (United States)

    Threeton, Mark D.; Evanoski, Danielle C.

    2014-01-01

    In an effort to provide additional insight on providing a secure teaching and learning environment within schools, this study sought to: (1) explore the safety and health practices within Career and Technical Education (CTE); and (2) identify the perceived obstacles which appear to hinder implementation of health and safety programs. While it…

  8. Nature-based strategies for improving urban health and safety

    Science.gov (United States)

    Michelle C. Kondo; Eugenia C. South; Charles C. Branas

    2015-01-01

    Place-based programs are being noticed as key opportunities to prevent disease and promote public health and safety for populations at-large. As one key type of place-based intervention, nature-based and green space strategies can play an especially large role in improving health and safety for dwellers in urban environments such as US legacy cities that lack nature...

  9. Principles and Practices of Occupational Safety and Health: Administrator's Manual.

    Science.gov (United States)

    Occupational Safety and Health Administration, Washington, DC.

    The manual guides an instructor in conducting a training course for first-line supervisors to familiarize them with six aspects relating to the Occupational Safety and Health Act of 1970: (1) requirements of the Act, (2) compliance with its standards, (3) identification of health and safety hazards, (4) correction of adverse conditions, (5) record…

  10. OCCUPATIONAL HEALTH AND SAFETY ACT NO.6331 AND TOXICOLOGY

    OpenAIRE

    AYAN, Burak

    2018-01-01

    Workers exposureto variety of hazardous chemicals related to the type of work carried out. Regulationsabout chemicals which may be unsafe for workers is regulated at theOccupational Health and Safety Act No.6331.In this review regulatory framework of occupational health and safety forchemicals are assessed in order for chemicals to be used properly andsafely. 

  11. 78 FR 11092 - Safety and Health Regulations for Construction

    Science.gov (United States)

    2013-02-15

    ... LABOR DEPARTMENT Occupational Safety and Health Administration 29 CFR Part 1926 Safety and Health Regulations for Construction CFR Correction In Title 29 of the Code of Federal Regulations, Part 1926, revised as of July 1, 2012, on page 225, in Sec. 1926.152, paragraph (c)(16) is added to read as follows: Sec...

  12. Health and Safety Legislation in Australia: Complexity for Training Remains

    Science.gov (United States)

    Bahn, Susanne; Barratt-Pugh, Llandis

    2014-01-01

    This paper presents the findings from a study that examined the impact of the National Occupational Health and Safety Strategy 2002-2012 and the harmonisation of the Work Health and Safety Act 2011 on Australian training design, delivery and outcomes. There has been a comparative reduction in work related injuries, fatalities and disease, and…

  13. Measuring safety climate in a nuclear power plant - an experience sharing

    International Nuclear Information System (INIS)

    Vincy, M.U.; Varshney, Aloke; Khot, Pankaj

    2016-01-01

    In this paper the author discusses the experience gained in safety climate measurement of an Indian nuclear power plant. Safety performance is increasingly part of an organization's sustainable development. Nuclear power stations are falling under the category 'high reliability' industries in the world as far as work safety is concerned. Both the research and the practical experience continually point to two underlying factors that drive safety outcomes: the quality of an organisation's leadership and the resulting culture. After years of development in safety technology and safety management system in the industry, management of nuclear industry world over has come to recognize that safety culture has to be addressed if high standards of health and safety are to be maintained. Therefore, nuclear industries in India have been carrying out measurement of safety climate for more than ten years. The objectives of the study are to examine people's values, attitude, perception, competencies, and patterns of behaviour that determine the commitment to, and effectiveness of health and safety management in the industry based on a questionnaires survey and their analysis

  14. Health IT for Patient Safety and Improving the Safety of Health IT.

    Science.gov (United States)

    Magrabi, Farah; Ong, Mei-Sing; Coiera, Enrico

    2016-01-01

    Alongside their benefits health IT applications can pose new risks to patient safety. Problems with IT have been linked to many different types of clinical errors including prescribing and administration of medications; as well as wrong-patient, wrong-site errors, and delays in procedures. There is also growing concern about the risks of data breach and cyber-security. IT-related clinical errors have their origins in processes undertaken to design, build, implement and use software systems in a broader sociotechnical context. Safety can be improved with greater standardization of clinical software and by improving the quality of processes at different points in the technology life cycle, spanning design, build, implementation and use in clinical settings. Oversight processes can be set up at a regional or national level to ensure that clinical software systems meet specific standards. Certification and regulation are two mechanisms to improve oversight. In the absence of clear standards, guidelines are useful to promote safe design and implementation practices. Processes to identify and mitigate hazards can be formalised via a safety management system. Minimizing new patient safety risks is critical to realizing the benefits of IT.

  15. Measuring health inequalities over time

    Directory of Open Access Journals (Sweden)

    Gustavo Bergonzoli

    2007-11-01

    Full Text Available Background: several methodologies have been used to measure health inequalities. Most of them do so in a cross- sectional fashion, causing significant loss of information. None of them measure health inequalities in social territories over time. Methods: this article presents two approaches measure health inequalities: one approach consists of a refinement of cross-sectional study, by using the analysis of ANOVA variance (ANOVA procedure to explore whether the gap between social territories is real or due to chance. Several adjustments were made to limit errors inevitably found in multiple comparisons. Polynomial procedures were then applied to identify and evaluate any trends. The second sociales se utilizó approach measures the health gap between social territories or strata (as defined in this study over time using the Poisson regression. These approaches were applied using life expectancy and maternal mortality data from Venezuela. Results: a positive relationship between tendenterritories and life expectancy was found, with a significant cia linal trend. The relation between maternal mortality and materna y territorios sociales fue cuadrática. La medición desocial territories was quadratic. The measurement of the la brecha, gap between least developed social territory and the most, a developed territory showed a gap reduction from the first to the second decade, mainly because of an increase of territorio social maternal mortality in the more developed area, rather than a real improvement in the least developed. Conclusions: study helps to clarify the impact that public policies and interventions have in reducing the health gap. Knowledge that a health gap between social territories can decrease without showing improvement in the least developed sector , is an important finding for monitoring and evaluating health interventions for improving living and health conditions in the population.

  16. The Danish patient safety experience: the Act on Patient Safety in the Danish Health care system

    DEFF Research Database (Denmark)

    Lundgaard, Mette; Rabøl, Louise; Jensen, Elisabeth Agnete Brøgger

    2005-01-01

    This paper describes the process that lead to the passing of the Act for Patient Safety in the Danisk health care sytem, the contents of the act and how the act is used in the Danish health care system. The act obligates frontline health care personnel to report adverse events, hospital owners...... to act on the reports and the National Board of Health to commuicate the learning nationally. The act protects health care providers from sanctions as a result of reporting. In January 2004, the Act on Patient Safety in the Danish health care system was put into force. In the first twelve months 5740...... adverse events were reported. the reports were analyzed locally (hospital and region), anonymized ad then sent to the National Board af Health. The Act on Patient Safety has driven the work with patient safety forward but there is room for improvement. Continuous and improved feedback from all parts...

  17. Environment, safety, and health regulatory implementation plan

    International Nuclear Information System (INIS)

    1993-01-01

    To identify, document, and maintain the Uranium Mill Tailings Remedial Action (UMTRA) Project's environment, safety, and health (ES ampersand H) regulatory requirements, the US Department of Energy (DOE) UMTRA Project Office tasked the Technical Assistance Contractor (TAC) to develop a regulatory operating envelope for the UMTRA Project. The system selected for managing the UMTRA regulatory operating envelope data bass is based on the Integrated Project Control/Regulatory Compliance System (IPC/RCS) developed by WASTREN, Inc. (WASTREN, 1993). The IPC/RCS is a tool used for identifying regulatory and institutional requirements and indexing them to hardware, personnel, and program systems on a project. The IPC/RCS will be customized for the UMTRA Project surface remedial action and groundwater restoration programs. The purpose of this plan is to establish the process for implementing and maintaining the UMTRA Project's regulatory operating envelope, which involves identifying all applicable regulatory and institutional requirements and determining compliance status. The plan describes how the Project will identify ES ampersand H regulatory requirements, analyze applicability to the UMTRA Project, and evaluate UMTRA Project compliance status

  18. UMTRA Project: Environment, Safety, and Health Plan

    International Nuclear Information System (INIS)

    1995-02-01

    The US Department of Energy has prepared this UMTRA Project Environment, Safety, and Health (ES and H) Plan to establish the policy, implementing requirements, and guidance for the UMTRA Project. The requirements and guidance identified in this plan are designed to provide technical direction to UMTRA Project contractors to assist in the development and implementation of their ES and H plans and programs for UMTRA Project work activities. Specific requirements set forth in this UMTRA Project ES and H Plan are intended to provide uniformity to the UMTRA Project's ES and H programs for processing sites, disposal sites, and vicinity properties. In all cases, this UMTRA Project ES and H Plan is intended to be consistent with applicable standards and regulations and to provide guidance that is generic in nature and will allow for contractors' evaluation of site or contract-specific ES and H conditions. This plan specifies the basic ES and H requirements applicable to UMTRA Project ES and H programs and delineates responsibilities for carrying out this plan. DOE and contractor ES and H personnel are expected to exercise professional judgment and apply a graded approach when interpreting these guidelines, based on the risk of operations

  19. The impact of health information technology on patient safety.

    Science.gov (United States)

    Alotaibi, Yasser K; Federico, Frank

    2017-12-01

    Since the original Institute of Medicine (IOM) report was published there has been an accelerated development and adoption of health information technology with varying degrees of evidence about the impact of health information technology on patient safety.  This article is intended to review the current available scientific evidence on the impact of different health information technologies on improving patient safety outcomes. We conclude that health information technology improves patient's safety by reducing medication errors, reducing adverse drug reactions, and improving compliance to practice guidelines. There should be no doubt that health information technology is an important tool for improving healthcare quality and safety. Healthcare organizations need to be selective in which technology to invest in, as literature shows that some technologies have limited evidence in improving patient safety outcomes.

  20. The impact of health information technology on patient safety

    Directory of Open Access Journals (Sweden)

    Yasser K. Alotaibi

    2017-12-01

    Full Text Available Since the original Institute of Medicine (IOM report was published there has been an accelerated development and adoption of health information technology with varying degrees of evidence about the impact of health information technology on patient safety. This article is intended to review the current available scientific evidence on the impact of different health information technologies on improving patient safety outcomes. We conclude that health information technology improves patient’s safety by reducing medication errors, reducing adverse drug reactions, and improving compliance to practice guidelines. There should be no doubt that health information technology is an important tool for improving healthcare quality and safety. Healthcare organizations need to be selective in which technology to invest in, as literature shows that some technologies have limited evidence in improving patient safety outcomes.

  1. Utilization of mathematics amongst healthcare students towards problem solving during their occupational safety health internship

    Science.gov (United States)

    Umasenan a/l Thanikasalam

    2017-05-01

    Occupational safety health is a multidisciplinary discipline concentrating on the safety, health and welfare of workers in the working place. Healthcare Students undergoing Occupational Safety Health internships are required to apply mathematical in areas such as safety legislation, safety behavior, ergonomics, chemical safety, OSH practices, industrial hygiene, risk management and safety health practices as problem solving. The aim of this paper is to investigate the level of mathematics and logic utilization from these students during their internship looking at areas of Hazard identification, Determining the population exposed to the hazard, Assessing the risk of the exposure to the hazards and Taking preventive and control. A total of 142 returning healthcare students from their Occupational Safety Health, internship were given a questionnaire to measure their perceptions towards mathematical and logic utilization. The overall results indicated a strong positive skewed result towards the use of Mathematics during their internship. The findings showed that mathematics were well delivered by the students during their internship. Mathematics could not be separated from OSH practice as a needed precision in quantifying safety, health an d welfare of workers in addition to empiricism.

  2. Industrial Safety and Applied Health Physics Division, annual report for 1982

    International Nuclear Information System (INIS)

    1983-12-01

    Activities during the past year are summarized for the Health Physics Department, the Environmental Management Department, and the Safety Department. The Health Physics Department conducts radiation and safety surveys, provides personnel monitoring services for both external and internal radiation, and procures, services, and calibrates appropriate portable and stationary health physics instruments. The Environmental Management Department insures that the activities of the various organizations within ORNL are carried out in a responsible and safe manner. This responsibility involves the measurement, field monitoring, and evaluation of the amounts of radionuclides and hazardous materials released to the environment and the control of hazardous materials used within ORNL. The department also collaborates in the design of ORNL Facilities to help reduce the level of materials released to the environment. The Safety Department is responsible for maintaining a high level of staff safety. This includes aspects of both operational and industrial safety and also coordinates the activities of the Director's Safety Review Committee

  3. Industrial Safety and Applied Health Physics Division, annual report for 1982

    Energy Technology Data Exchange (ETDEWEB)

    1983-12-01

    Activities during the past year are summarized for the Health Physics Department, the Environmental Management Department, and the Safety Department. The Health Physics Department conducts radiation and safety surveys, provides personnel monitoring services for both external and internal radiation, and procures, services, and calibrates appropriate portable and stationary health physics instruments. The Environmental Management Department insures that the activities of the various organizations within ORNL are carried out in a responsible and safe manner. This responsibility involves the measurement, field monitoring, and evaluation of the amounts of radionuclides and hazardous materials released to the environment and the control of hazardous materials used within ORNL. The department also collaborates in the design of ORNL Facilities to help reduce the level of materials released to the environment. The Safety Department is responsible for maintaining a high level of staff safety. This includes aspects of both operational and industrial safety and also coordinates the activities of the Director's Safety Review Committee. (ACR)

  4. What is Clinical Safety in Electronic Health Care Record Systems?

    Science.gov (United States)

    Davies, George

    There is mounting public awareness of an increasing number of adverse clinical incidents within the National Health Service (NHS), but at the same time, large health care projects like the National Programme for IT (NPFIT) are claiming that safer care is one of the benefits of the project and that health software systems in particular have the potential to reduce the likelihood of accidental or unintentional harm to patients. This paper outlines the approach to clinical safety management taken by CSC, a major supplier to NPFIT; discusses acceptable levels of risk and clinical safety as an end-to-end concept; and touches on the future for clinical safety in health systems software.

  5. Perceived school safety is strongly associated with adolescent mental health problems.

    Science.gov (United States)

    Nijs, Miesje M; Bun, Clothilde J E; Tempelaar, Wanda M; de Wit, Niek J; Burger, Huibert; Plevier, Carolien M; Boks, Marco P M

    2014-02-01

    School environment is an important determinant of psychosocial function and may also be related to mental health. We therefore investigated whether perceived school safety, a simple measure of this environment, is related to mental health problems. In a population-based sample of 11,130 secondary school students, we analysed the relationship of perceived school safety with mental health problems using multiple logistic regression analyses to adjust for potential confounders. Mental health problems were defined using the clinical cut-off of the self-reported Strengths and Difficulties Questionnaire. School safety showed an exposure-response relationship with mental health problems after adjustment for confounders. Odds ratios increased from 2.48 ("sometimes unsafe") to 8.05 ("very often unsafe"). The association was strongest in girls and young and middle-aged adolescents. Irrespective of the causal background of this association, school safety deserves attention either as a risk factor or as an indicator of mental health problems.

  6. Awareness of Occupational Injuries and Utilization of Safety Measures among Welders in Coastal South India

    Directory of Open Access Journals (Sweden)

    S Ganesh Kumar

    2013-10-01

    Full Text Available Background: Awareness of occupational hazards and its safety precautions among welders is an important health issue, especially in developing countries. Objective: To assess the awareness of occupational hazards and utilization of safety measures among welders in coastal South India. Methods: A cross-sectional study was conducted among 209 welders in Puducherry, South India. Baseline characteristics, awareness of health hazards, safety measures and their availability to and utilization by the participants were assessed using a pre-tested structured questionnaire. Results: The majority of studied welders aged between 20 and 40 years (n=160, 76.6% and had 1-10 years of education (n=181, 86.6%. They were more aware of hazards (n=174, 83.3% than safety measures (n=134, 64.1%. The majority of studied welders utilized at least one protective measure in the preceding week (n=200, 95.7%. Many of them had more than 5 years of experience (n=175, 83.7%, however, only 20% of them had institutional training (n=40, 19.1%. Age group, education level, and utilization of safety measures were significantly associated with awareness of hazards in univariate analysis (p<0.05. Conclusion: Awareness of occupational hazards and utilization of safety measures is low among welders in coastal South India, which highlights the importance of strengthening safety regulatory services towards this group of workers.

  7. Health economics of blood transfusion safety

    NARCIS (Netherlands)

    Hulst, Marinus van

    2008-01-01

    The HIV/AIDS disaster in transfusion medicine shaped the future agendas for blood transfusion safety. More than ever before, the implementation of interventions which could improve blood transfusion safety was driven merely by availability of technology. The introduction of new expensive

  8. Fire Safety Trianing in Health Care Institutions.

    Science.gov (United States)

    American Hospital Association, Chicago, IL.

    The manual details the procedures to be followed in developing and implementing a fire safety plan. The three main steps are first, to organize; second, to set up a procedure and put it in writing; and third, to train and drill employees and staff. Step 1 involves organizing a safety committee, appointing a fire marshall, and seeking help from…

  9. DANGERS AND SAFETY MEASURES IN A MOUNTAIN

    Directory of Open Access Journals (Sweden)

    Jovica Petković

    2013-07-01

    Full Text Available Mountaineering and everything that is connected with it is a sport with con¬tro¬lled risk. Mountaineers, alpinists, climbers, cavers and all the others who visit and sojourn in mountains are faced with many risks and dangers, which are caused by na¬ture and also by their own mistakes. The dangers in the mountains, like dangers in any other environment, are mainly predictable, so it is best to deal with them with good esti¬mation, knowledge and skill. One has to be aware of his surroundings – the moun¬tain, to respect it and to know what is dangerous and how much it is dangerous at any moment. The organization of the mountaineering expeditions and leadership per¬haps re¬present the highest level of security control. To develop skills for organizing and lead¬ing a group means to ensure the safety of the entire group – to work pre¬ven¬ti¬ve¬ly at the level of the entire group, not only at the level of an individual. The success of the enti¬re group as well as safety depends on the organization and leadership.

  10. Advancing perinatal patient safety through application of safety science principles using health IT.

    Science.gov (United States)

    Webb, Jennifer; Sorensen, Asta; Sommerness, Samantha; Lasater, Beth; Mistry, Kamila; Kahwati, Leila

    2017-12-19

    The use of health information technology (IT) has been shown to promote patient safety in Labor and Delivery (L&D) units. The use of health IT to apply safety science principles (e.g., standardization) to L&D unit processes may further advance perinatal safety. Semi-structured interviews were conducted with L&D units participating in the Agency for Healthcare Research and Quality's (AHRQ's) Safety Program for Perinatal Care (SPPC) to assess units' experience with program implementation. Analysis of interview transcripts was used to characterize the process and experience of using health IT for applying safety science principles to L&D unit processes. Forty-six L&D units from 10 states completed participation in SPPC program implementation; thirty-two (70%) reported the use of health IT as an enabling strategy for their local implementation. Health IT was used to improve standardization of processes, use of independent checks, and to facilitate learning from defects. L&D units standardized care processes through use of electronic health record (EHR)-based order sets and use of smart pumps and other technology to improve medication safety. Units also standardized EHR documentation, particularly related to electronic fetal monitoring (EFM) and shoulder dystocia. Cognitive aids and tools were integrated into EHR and care workflows to create independent checks such as checklists, risk assessments, and communication handoff tools. Units also used data from EHRs to monitor processes of care to learn from defects. Units experienced several challenges incorporating health IT, including obtaining organization approval, working with their busy IT departments, and retrieving standardized data from health IT systems. Use of health IT played an integral part in the planning and implementation of SPPC for participating L&D units. Use of health IT is an encouraging approach for incorporating safety science principles into care to improve perinatal safety and should be incorporated

  11. Health, Safety, and Environment Division: Annual progress report 1987

    Energy Technology Data Exchange (ETDEWEB)

    Rosenthal, M.A. (comp.)

    1988-04-01

    The primary responsibility of the Health, Safety, and Environment (HSE) Division at the Los Alamos National Laboratory is to provide comprehensive occupational health and safety programs, waste processing, and environment protection. These activities are designed to protect the worker, the public, and the environment. Many disciplines are required to meet the responsibilities, including radiation protection, industrial hygiene, safety, occupational medicine, environmental science, epidemiology, and waste management. New and challenging health and safety problems arise occasionally from the diverse research and development work of the Laboratory. Research programs in HSE Division often stem from these applied needs. These programs continue but are also extended, as needed to study specific problems for the Department of Energy and to help develop better occupational health and safety practices.

  12. Health, Safety, and Environment Division: Annual progress report 1987

    International Nuclear Information System (INIS)

    Rosenthal, M.A.

    1988-04-01

    The primary responsibility of the Health, Safety, and Environment (HSE) Division at the Los Alamos National Laboratory is to provide comprehensive occupational health and safety programs, waste processing, and environment protection. These activities are designed to protect the worker, the public, and the environment. Many disciplines are required to meet the responsibilities, including radiation protection, industrial hygiene, safety, occupational medicine, environmental science, epidemiology, and waste management. New and challenging health and safety problems arise occasionally from the diverse research and development work of the Laboratory. Research programs in HSE Division often stem from these applied needs. These programs continue but are also extended, as needed to study specific problems for the Department of Energy and to help develop better occupational health and safety practices

  13. Health, Safety, and Environment Division annual report, 1988

    International Nuclear Information System (INIS)

    Rosenthal, M.A.

    1989-10-01

    The primary responsibility of the Health, Safety, and Environment (HSE) Division at the Los Alamos National Laboratory is to provide comprehensive occupational health and safety programs, waste processing, and environmental protection. These activities are designed to protect the worker, the public, and the environment. Many disciplines are required to meet the responsibilities, including radiation protection, industrial hygiene, safety, occupational medicine, environmental science, epidemiology, and waste management. New and challenging health and safety problems occasionally arise from the diverse research and development work of the Laboratory. Research programs in HSE Division often stem from these applied needs. These programs continue but are also extended, as needed, to study specific problems for the Department of Energy and to help develop better occupational health and safety practices. 52 refs

  14. Health, Safety and Environmental Risk Assessment in Laboratory Sites

    Directory of Open Access Journals (Sweden)

    2012-05-01

    Full Text Available Introduction: ”Exposing to danger” or in other words, “risk” is a process which is led to an uncertain result in every field. Project risks are uncertain contingent events or situations that if they occur will have positive or negative effects on project’s objectives. Todays, research and educational process and more complicated and the professional risk management become much more difficult, as a result. .Material and Method: In this research, the health and safety issues have been studied and analyzed using ISO 14121 and the environmental issues by EMEA to determine the risk level separately for research laboratories and to prioritize corrective measure in each field (school. .Result: The finding in this study showed that from all the main risks within the rage of 38-86 percent have been decreased. Moreover average of the risk level for the health, safety and environment cases showed a significant decrease (Pvalue<0.0001 by implement controlling and protective countermeasures compariy to the priority state without any measures. . Conclusion: The risk assessment with hazards control strategy based on ISO 14121 is a compatible method in laboratory site as universities and other reasearch sites.

  15. The occupational health and safety of flight attendants.

    Science.gov (United States)

    Griffiths, Robin F; Powell, David M C

    2012-05-01

    In order to perform safety-critical roles in emergency situations, flight attendants should meet minimum health standards and not be impaired by factors such as fatigue. In addition, the unique occupational and environmental characteristics of flight attendant employment may have consequential occupational health and safety implications, including radiation exposure, cancer, mental ill-health, musculoskeletal injury, reproductive disorders, and symptoms from cabin air contamination. The respective roles of governments and employers in managing these are controversial. A structured literature review was undertaken to identify key themes for promoting a future agenda for flight attendant health and safety. Recommendations include breast cancer health promotion, implementation of Fatigue Risk Management Systems, standardization of data collection on radiation exposure and health outcomes, and more coordinated approaches to occupational health and safety risk management. Research is ongoing into cabin air contamination incidents, cancer, and fatigue as health and safety concerns. Concerns are raised that statutory medical certification for flight attendants will not benefit either flight safety or occupational health.

  16. The Health and Safety Executive's regulatory framework for control of nuclear criticality safety

    International Nuclear Information System (INIS)

    Smith, K.; Simister, D.N.

    1991-01-01

    In the United Kingdom the Health and Safety at Work Act, 1974 is the main legal instrument under which risks to people from work activities are controlled. Certain sections of the Nuclear Installations Act, 1965 which deal with the licensing of nuclear sites and the regulatory control of risks arising from them, including the risk from accidental criticality, are relevant statutory provisions of the Health and Safety at Work Act. The responsibility for safety rests with the operator who has to make and implement arrangements to prevent accidental criticality. The adequacy of these arrangements must be demonstrated in a safety case to the regulatory authorities. Operators are encouraged to treat each plant on its own merits and develop the safety case accordingly. The Nuclear Installations Inspectorate (NII), for its part, assesses the adequacy of the operator's safety case against the industry's own standards and criteria, but more particularly against the NII's safety assessment principles and guides, and international standards. Risks should be made as low as reasonably practicable. Generally, the NII seeks improvements in safety using an enforcement policy which operates at a number of levels, ranging from persuasion through discussion to the ultimate deterrent of withdrawal of a site licence. This paper describes the role of the NII, which includes a specialist criticality expertise, within the Health and Safety Executive, in regulating the nuclear sites from the criticality safety viewpoint. (Author)

  17. Role and tasks of the Mine Safety and Health Administration

    Energy Technology Data Exchange (ETDEWEB)

    Bradecki, W. (Wyzszy Urzad Gorniczy, Katowice (Poland))

    1992-01-01

    Discusses the visit of 2 representatives of the Mine Safety and Health Administration and the West Mining Company from the United States to Poland in November 1991. During the visit, occupational safety in underground coal mines in Upper Silesia was evaluated. Selected aspects of experience and organization schemes of the Mine Safety and Health Administration are evaluated from the point of view of their use in Poland to increase occupational safety in coal mining. The following aspects are discussed: Mine Safety and Health Administration and its budget (US$ 186 million), personnel (2,700), research institutes that specialize in mine safety (the National Institute of Occupational Safety and Health, Bureau of Mines), natural hazards associated with mining, mine safety in underground and surface coal mines in the USA in relation to number of coal miners and coal output, job safety analysis as a key to the success of the MSHA, increased hazards in small mines (Pennsylvania, West Virginia, Virginia and Kentucky), problems of drug addiction and alcoholism among coal miners.

  18. Twenty sixth DAE safety and occupational health professionals meet: cryogenic safety, electrical safety and ergonomics at work place

    International Nuclear Information System (INIS)

    2009-01-01

    This conference gathered knowledge in safety and occupational health hazards in various fields of nuclear science and technology like radiations, high voltages, ultra-low temperature, ultra-high magnetic fields, electrical breakdown, fire, ergonomics and cryogenic safety at work place. Papers relevant to INIS database are indexed separately

  19. Surgical Safety Training of World Health Organization Initiatives.

    Science.gov (United States)

    Davis, Christopher R; Bates, Anthony S; Toll, Edward C; Cole, Matthew; Smith, Frank C T; Stark, Michael

    2014-01-01

    Undergraduate training in surgical safety is essential to maximize patient safety. This national review quantified undergraduate surgical safety training. Training of 2 international safety initiatives was quantified: (1) World Health Organization (WHO) "Guidelines for Safe Surgery" and (2) Department of Health (DoH) "Principles of the Productive Operating Theatre." Also, 13 additional safety skills were quantified. Data were analyzed using Mann-Whitney U tests. In all, 23 universities entered the study (71.9% response). Safety skills from WHO and DoH documents were formally taught in 4 UK medical schools (17.4%). Individual components of the documents were taught more frequently (47.6%). Half (50.9%) of the additional safety skills identified were taught. Surgical societies supplemented safety training, although the total amount of training provided was less than that in university curricula (P < .0001). Surgical safety training is inadequate in UK medical schools. To protect patients and maximize safety, a national undergraduate safety curriculum is recommended. © 2013 by the American College of Medical Quality.

  20. Safety and health: Principles and practices in the laboratory

    International Nuclear Information System (INIS)

    Fakhrul Razi Ahmadun; Guan, Chuan Teong; Mohd Halim Shah Ismail

    2005-01-01

    Ignorance, carelessness or improper practices in the laboratory or the improper handling of hazardous or toxic materials may lead to work accidents and work-related ill-health. Laboratory users and administrators cannot afford to overlook these possible consequences due to the misconduct of laboratory practices and should decide how best to manage the health and safety aspects in the laboratory. This book has been written for safety representatives of colleges and universities, for lectures, teachers and students, and for researchers working in laboratories. It is also for everyone responsible for laboratory safety, laboratory accidents and their consequences. The emphasis is on hazards to health and safety, with the focus on the general hazards in the laboratory, how they arise and how to prevent, how to eliminate and control them. Special hazards will also be discussed such as radiation hazards and human factors. This book also provides information on governmental and non-governmental agencies and authorities, emergency contact numbers of relevant authorities, a list of Malaysia occupational safety and health related legislation and some useful occupational safety and health web sites. Readers will find that the information contained in this book will serve as the foundation for laboratory users safety policy. A set of Laboratory Safety Forms for a typical laboratory is also available in the appendix for reference. Laboratory users can use and adapt these forms for their own laboratory requirements. (author)

  1. Regulatory role and approach of BARC Safety Council in safety and occupational health in BARC facilities

    International Nuclear Information System (INIS)

    Rajdeep; Jayarajan, K.; Taly, Y.K.

    2016-01-01

    Bhabha Atomic Research Centre is involved in multidisciplinary research and developmental activities, related to peaceful use of nuclear energy and its societal benefits. In order to achieve high level of performance of these facilities, the best efforts are made to maintain good health of the plant personnel and good working conditions. BARC Safety Council (BSC), which is the regulatory body for BARC facilities, regulates radiation safety, industrial safety and surveillance of occupational health, by implementing various rules and guidelines in BARC facilities. BARC Safety framework consists of various committees in a 3-tier system. The first tier is BSC, which is the apex body authorized for issuing directives, permissions, consents and authorizations. It is having responsibility of ensuring protection and safety of public, environment, personnel and facilities of BARC through enforcement of radiation protection and industrial safety programmes. Besides the 18 committees in 2"n"d tier, there are 6 other expert committees which assist in functioning of BSC. (author)

  2. Simplifying documentation while approaching site closure: integrated health and safety plans as documented safety analysis

    International Nuclear Information System (INIS)

    Brown, Tulanda

    2003-01-01

    At the Fernald Closure Project (FCP) near Cincinnati, Ohio, environmental restoration activities are supported by Documented Safety Analyses (DSAs) that combine the required project-specific Health and Safety Plans, Safety Basis Requirements (SBRs), and Process Requirements (PRs) into single Integrated Health and Safety Plans (I-HASPs). By isolating any remediation activities that deal with Enriched Restricted Materials, the SBRs and PRs assure that the hazard categories of former nuclear facilities undergoing remediation remain less than Nuclear. These integrated DSAs employ Integrated Safety Management methodology in support of simplified restoration and remediation activities that, so far, have resulted in the decontamination and demolition (D and D) of over 150 structures, including six major nuclear production plants. This paper presents the FCP method for maintaining safety basis documentation, using the D and D I-HASP as an example

  3. Regulatory system reform of occupational health and safety in China.

    Science.gov (United States)

    Wu, Fenghong; Chi, Yan

    2015-01-01

    With the explosive economic growth and social development, China's regulatory system of occupational health and safety now faces more and more challenges. This article reviews the history of regulatory system of occupational health and safety in China, as well as the current reform of this regulatory system in the country. Comprehensive, a range of laws, regulations and standards that promulgated by Chinese government, duties and responsibilities of the regulatory departments are described. Problems of current regulatory system, the ongoing adjustments and changes for modifying and improving regulatory system are discussed. The aim of reform and the incentives to drive forward more health and safety conditions in workplaces are also outlined.

  4. FMCSA safety program effectiveness measurement: intervention model fiscal year 2009.

    Science.gov (United States)

    2013-04-01

    The Federal Motor Carrier Safety Administration (FMCSA), in cooperation with the researcher, has developed an analytic model to measure the effectiveness of roadside inspections and traffic enforcements in terms of crashes avoided, injuries avoided, ...

  5. Health and safety annual report 1987

    International Nuclear Information System (INIS)

    1988-01-01

    The principal activities and organisation of BNFL are reviewed in relation to the impact these activities have on the workforce, members of the general public and the environment, together with services for occupational safety within the company. (author)

  6. Measuring the safety culture in a hospital setting: a concept whose time has come?

    Science.gov (United States)

    Robb, Gillian; Seddon, Mary

    2010-05-14

    Getting the right 'patient safety culture' is thought to be an important component in improving patient safety in hospitals, however there is a lack of clarity in how best to measure and improve it, and whether such improvement actually translates to better patient outcomes. This paper reflects on the Counties Manukau District Health Board (CMDHB) experience with a patient safety survey and attempts to answer questions other organisations may ask when deciding whether to invest in such survey. A literature search was undertaken to identify valid and reliable patient safety culture survey tools. These were reviewed with respect to how best to interpret and use the results. If hospitals decide to undertake a patient safety culture survey, the recommended survey tools are the Safety Attitudes Questionnaire (SAQ) and the Hospital Survey on Patient Safety (HSOPS). Both have been widely used and have sound and comprehensive psychometrics. Only the SAQ has established links with patient safety outcomes such as reduced healthcare associated infections. Surveys can provide some insights into the patient safety culture within an organisation, but the opportunity costs of undertaking a survey should be carefully considered. Much of their value lies in raising the profile of patient safety and promoting conversations; making patient safety 'the way we do business around here'.

  7. Tank farm health and safety plan. Revision 2

    International Nuclear Information System (INIS)

    Mickle, G.D.

    1995-01-01

    This Tank Farm Health and Safety Plan (HASP) for the conduct of all operations and work activities at the Hanford Site 200 Area Tank Farms is provided in order to minimize health and safety risks to workers and other onsite personnel. The HASP accomplishes this objective by establishing requirements, providing general guidelines, and conveying farm and facility-specific hazard communication information. The HASP, in conjunction with the job-specific information required by the HASP, is provided also as a reference for use during the planning of work activities at the tank farms. This HASP applies to Westinghouse Hanford Company (WHC), other prime contractors to the U.S. Department of Energy (DOE), and subcontractors to WHC who may be involved in tank farm work activities. This plan is intended to be both a requirements document and a useful reference to aid tank farm workers in understanding the safety and health issues that are encountered in routine and nonroutine work activities. The HASP defines the health and safety responsibilities of personnel working at the tank farms. It has been prepared in recognition of and is consistent with National Institute of Safety and Health (NIOSH), and Occupational Safety and Health Administration (OSHA)/Unlimited State Coast Guard (USCG)/U.S. Environmental Protection Agency (EPA), Occupational Safety and Health Guidance Manual for Hazardous Waste Site Activities (NIOSH 1985); WHC-CM-4-3, Industrial Safety Manual, Volume 4, open-quotes Health and Safety Programs for Hazardous Waste Operations;close quotes 29 CFR 1910.120, Hazardous Waste Operations and Emergency Response; WHC-CM-1-1, Management Policies; and WHC-CM-1-3, Management Requirements and Procedures. When differences in governing regulations or policies exist, the more stringent requirements shall apply until the discrepancy can be resolved

  8. Tank farm health and safety plan. Revision 2

    Energy Technology Data Exchange (ETDEWEB)

    Mickle, G.D.

    1995-03-29

    This Tank Farm Health and Safety Plan (HASP) for the conduct of all operations and work activities at the Hanford Site 200 Area Tank Farms is provided in order to minimize health and safety risks to workers and other onsite personnel. The HASP accomplishes this objective by establishing requirements, providing general guidelines, and conveying farm and facility-specific hazard communication information. The HASP, in conjunction with the job-specific information required by the HASP, is provided also as a reference for use during the planning of work activities at the tank farms. This HASP applies to Westinghouse Hanford Company (WHC), other prime contractors to the U.S. Department of Energy (DOE), and subcontractors to WHC who may be involved in tank farm work activities. This plan is intended to be both a requirements document and a useful reference to aid tank farm workers in understanding the safety and health issues that are encountered in routine and nonroutine work activities. The HASP defines the health and safety responsibilities of personnel working at the tank farms. It has been prepared in recognition of and is consistent with National Institute of Safety and Health (NIOSH), and Occupational Safety and Health Administration (OSHA)/Unlimited State Coast Guard (USCG)/U.S. Environmental Protection Agency (EPA), Occupational Safety and Health Guidance Manual for Hazardous Waste Site Activities (NIOSH 1985); WHC-CM-4-3, Industrial Safety Manual, Volume 4, {open_quotes}Health and Safety Programs for Hazardous Waste Operations;{close_quotes} 29 CFR 1910.120, Hazardous Waste Operations and Emergency Response; WHC-CM-1-1, Management Policies; and WHC-CM-1-3, Management Requirements and Procedures. When differences in governing regulations or policies exist, the more stringent requirements shall apply until the discrepancy can be resolved.

  9. Development of a safety decision-making scenario to measure worker safety in agriculture.

    Science.gov (United States)

    Mosher, G A; Keren, N; Freeman, S A; Hurburgh, C R

    2014-04-01

    Human factors play an important role in the management of occupational safety, especially in high-hazard workplaces such as commercial grain-handling facilities. Employee decision-making patterns represent an essential component of the safety system within a work environment. This research describes the process used to create a safety decision-making scenario to measure the process that grain-handling employees used to make choices in a safety-related work task. A sample of 160 employees completed safety decision-making simulations based on a hypothetical but realistic scenario in a grain-handling environment. Their choices and the information they used to make their choices were recorded. Although the employees emphasized safety information in their decision-making process, not all of their choices were safe choices. Factors influencing their choices are discussed, and implications for industry, management, and workers are shared.

  10. Occupational Safety And Health (Osh From Islamic Perspective: A Conceptual Study

    Directory of Open Access Journals (Sweden)

    Afifah Binti Ismail

    2018-05-01

    Full Text Available ABSTRACT This paper illustrates occupational safety and health (OSH based on Islamic perspective in human resource management. This paper has been written based on the following objectives; ato state the duty of employer to provide safety workplace and to concern on employee health; bto list out the management system of OSH based on Islamic perspective as preventive measure. A purely qualitative approach of literature review was done and Islamic OSH is derived from Islamic principles which are guide by Al-Quran and sunnah. The responsibility to preserve safety and health of employee does not only relies to the employer solely but involved all workers, the government and the authority bodies as the runner for the Occupational safety and Health Act  OSHA 1994, Islamic order’s and policy to be implemented in the organization. The Occupational Safety and Health Master Plan (OSHMP 2020 is a tremendous incentive by the Ministry of Human Resource to cope and minimize the number of accident and injuries in Malaysia.   Keywords: Islamic occupational safety and health, employee safety and health, Islamic management system of OSH

  11. Integrating safety and health during deactiviation: With lessons learned from PUREX

    International Nuclear Information System (INIS)

    1995-01-01

    This report summarizes an integrated safety and health approach used during facility deactivation activities at the Department of Energy (DOE) Plutonium-Uranium Extraction (PUREX) Facility in Hanford, Washington. Resulting safety and health improvements and the potential, complex-wide application of this approach are discussed in this report through a description of its components and the impacts, or lessons-learned, of its use during the PUREX deactivation project. As a means of developing and implementing the integrated safety and health approach, the PUREX technical partnership was established in 1993 among the Office of Environment, Safety and Health's Office of Worker Health and Safety (EH-5); the Office of Environmental Management's Offices of Nuclear Material and Facility Stabilization (EM-60) and Compliance and Program Coordination (EM-20); the DOE Richland Operations Office; and the Westinghouse Hanford Company. It is believed that this report will provide guidance for instituting an integrated safety and health approach not only for deactivation activities, but for decommissioning and other clean-up activities as well. This confidence is based largely upon the rationality of the approach, often termed as common sense, and the measurable safety and health and project performance results that application of the approach produced during actual deactivation work at the PUREX Facility

  12. Safety for Compressed Gas and Air Equipment. Module SH-26. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on safety for compressed gas and air equipment is one of 50 modules concerned with job safety and health. This module presents technical data about commonly used gases and stresses the procedures necessary for safe handling of compressed gases. Following the introduction, 14 objectives (each keyed to a page in the text) the…

  13. Machine and Woodworking Tool Safety. Module SH-24. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on machine and woodworking tool safety is one of 50 modules concerned with job safety and health. This module discusses specific practices and precautions concerned with the efficient operation and use of most machine and woodworking tools in use today. Following the introduction, 13 objectives (each keyed to a page in the…

  14. Safety in Elevators and Grain Handling Facilities. Module SH-27. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on safety in elevators and grain handling facilities is one of 50 modules concerned with job safety and health. Following the introduction, 15 objectives (each keyed to a page in the text) the student is expected to accomplish are listed (e.g., Explain how explosion suppression works). Then each objective is taught in detail,…

  15. Safety Features of Material and Personnel Movement Devices. Module SH-25. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on safety features of material and personnel movement devices is one of 50 modules concerned with job safety and health. This module covers safe conditions and operating practices for conveyors, elevators, escalators, moving walks, manlifts, forklifts, and motorized hand trucks. Following the introduction, 10 objectives (each…

  16. Safety Capital: The Management of Organizational Knowledge on Occupational Health and Safety

    Science.gov (United States)

    Nunez, Imanol; Villanueva, Mikel

    2011-01-01

    Purpose: The concept of Safety Capital was developed by analyzing the creation and composition of the Intellectual Capital embedded in Occupational Health and Safety (OHS) systems. The paper aims to address this relationship. Design/methodology/approach: By drawing a theoretical link for the relationship between OHS activities and intellectual…

  17. Using objectives for managing safety and health

    International Nuclear Information System (INIS)

    Shoemaker, D.R.

    1990-01-01

    This morning I am going to talk about the International Mine Safety Rating System of the International Loss Control Institute. At the Questa mine we simply call it the ILCI System. The ILCI System has been in effect at Questa since 1982. Today, I want to offer you an outline of the system and a little bit of our experience with the system at Molycorp. In 1965, Molycorp started large-scale open-pit mining at Questa, New Mexico. In 1978 the decision was made to phase out surface mining and develop a large underground mine. Construction started in 1979, and production commenced in 1983. In 1982, with a work force approaching 900, and a 15-man safety department, we had an accident frequency rate twice the national average. At that point, as we were preparing to start underground production, we decided to become part of the International Safety Rating System. The International Safety Rating System (ISRS) is a modern safety program evaluation system. It provides the means for a systematic analysis of each element of the safety program to determine the extent and quality of management control. Auditing has long been an accepted management practice to ensure that critical business operations are performed in an efficient and profitable manner. Likewise, management has inadequate verification of the effectiveness of a safety program without the kind of audit this rating system provides. Today, largely because of the ILCI system our accident/incident rate has dropped to almost half the national average. Our production costs are nearly half of their historical high. A significant part of the savings has come from decreased expenditures for total accident losses as a result of our lower accident rates

  18. Sanitation health risk and safety planning in urban residential ...

    African Journals Online (AJOL)

    The aim of this review paper was to determine the best sanitation health risk and safety planning approach for sustainable management of urban environment. This was achieved by reviewing the concept of sanitation safety planning as a tool. The review adopted exploratory research approach and used secondary data ...

  19. Adult Learning in Health and Safety: Some Issues and Approaches.

    Science.gov (United States)

    O Fathaigh, Mairtin

    This document, which was developed for presentation at a seminar on adult learning and safety, examines approaches to occupational safety and health (OSH) learning/training in the workplace. Section 1 examines selected factors affecting adults' learning in workplace OSH programs. The principal dimensions along which individual adult learners will…

  20. Leadership and occupational safety and health (OSH): an expert analysis

    NARCIS (Netherlands)

    Elsler, D.; Flintrop, J.; Kaluza, S.; Hauke, A.; Starren, A.; Drupsteen, L.; Bell, N.

    2012-01-01

    In EU legislation as well as in scientific literature ever more attention is being paid to the important role of leadership in the improvement of Occupational Safety and Health (OSH). Improving the safety behaviour of employees requires understanding of the good leadership practices that can help

  1. Safety, Health, and Environmental Auditing A Practical Guide

    CERN Document Server

    Pain, Simon Watson

    2010-01-01

    A practical guide to environmental, safety, and occupational health audits. It allows organizations and business to avoid expensive external auditors and retain the knowledge and learning 'in-house'. It allows any competent manager or safety/environmental officer to undertake in-house audits in a competent and reproducible fashion.

  2. Safety study of PCC 2140 and ALILOG 21 used as part of safety measurement systems

    International Nuclear Information System (INIS)

    Meriaux, Pierre; Adnot, Serge; Rayrolles, Catherine.

    1978-03-01

    The PCC 2140 and ALILOG 21 equipment may be used at C.E.A. or E.D.F., as part of safety measurement systems. In a study of a similar, but earlier equipment, it was noticed that certain types of failures caused the system to switch to the least sensitive measurement range, which was detrimental to safety. This report analyses failure modes leading to unsafe failures and evaluates the risks ran into taking in account tests during use [fr

  3. 78 FR 24751 - Safety and Occupational Health Study Section (SOHSS), National Institute for Occupational Safety...

    Science.gov (United States)

    2013-04-26

    ... 14, 2013 (Closed) Place: Embassy Suites, 1900 Diagonal Road, Alexandria, Virginia 22314, Telephone... business and for the study section to consider safety and occupational health-related grant applications...

  4. 77 FR 75633 - Safety and Occupational Health Study Section (SOHSS), National Institute for Occupational Safety...

    Science.gov (United States)

    2012-12-21

    ... (Closed). 8:00 a.m.-5:00 p.m., February 22, 2013 (Closed). Place: Embassy Suites, 1900 Diagonal Road... conduct of Study Section business and for the study section to consider safety and occupational health...

  5. Health physics and safety in JAERI, No.17

    International Nuclear Information System (INIS)

    1975-09-01

    In the annual report No.17 (fiscal 1974), the activities of health physics and safety in the Tokyo Office, Tokai Research Establishment, Takasaki Radiation Chemistry Research Establishment, and Oarai Research Establishment are described. (auth.)

  6. Improving Patient Safety With the Military Electronic Health Record

    National Research Council Canada - National Science Library

    Charles, Marie-Jocelyne; Harmon, Bart J; Jordan, Pamela S

    2005-01-01

    The United States Department of Defense (DoD) has transformed health care delivery in its use of information technology to automate patient data documentation, leading to improvements in patient safety...

  7. Health and safety management practices in small and medium ...

    African Journals Online (AJOL)

    The Statistical Package for the Social Sciences (SPSS) version 20 was used to determine the ... poor health and safety performance within the construction industry in South Africa, ...... OHS performance in Australian construction industry.

  8. The status of occupational safety among health service providers in ...

    African Journals Online (AJOL)

    identify and bring under control at workplaces all health risks; provide ... on the status of occupational safety among hospital workers in Tanzania. ..... The assistance from the IPC/IS. National ... tions of the Healthcare Infection Prevention.

  9. The role of the Health and Safety Division of DNPDE

    International Nuclear Information System (INIS)

    Arkley, J.

    1985-01-01

    The paper concerns the role of the Health and Safety Division of the Dounreay Nuclear Power Development Establishment, Scotland. Radiological conditions in the workplace; dosimetry; off-site monitoring; and accidents and emergencies, are all discussed. (U.K.)

  10. Health and safety management practices in small and medium ...

    African Journals Online (AJOL)

    Health and safety management practices in small and medium enterprises in the ... on national economies, the construction industry receives additional attention in ... and training were considered key factors of H&S for SMCEs at project level.

  11. 23 CFR 635.108 - Health and safety.

    Science.gov (United States)

    2010-04-01

    ... CONSTRUCTION AND MAINTENANCE Contract Procedures § 635.108 Health and safety. Contracts for projects shall... to protect property in connection with the performance of the work covered by the contract. ...

  12. Calculating externalities from damages in occupational health and safety

    Energy Technology Data Exchange (ETDEWEB)

    Burtraw, D; Shefftz, J

    1994-07-01

    This paper surveys the theoretical basis for the possibility that coal miner occupational health and safety damages are not adequately internalized into the production cost of mining coal and thereby impose an external cost on society.

  13. Health physics and safety in JAERI, No. 18

    International Nuclear Information System (INIS)

    1976-10-01

    In the annual report No.18 (fiscal 1975), the activities of health physics and safety in the Tokyo Office, Tokai Research Establishment, Takasaki Radiation Chemistry Research Establishment, and Oarai Research Establishment are described. (auth.)

  14. TEL4Health – Mobile tools to improve patient safety

    NARCIS (Netherlands)

    Drachsler, Hendrik; Kalz, Marco; Specht, Marcus

    2013-01-01

    Drachsler, H., Kalz, M., & Specht, M. (2013, 10 October). TEL4Health – Mobile tools to improve patient safety. Presentation given at the blended learning platform of the Netherlands Organisation for Hospitals (Nederlandse Vereniging van Ziekenhuizen), Utrecht, The Netherlands.

  15. Calculating externalities from damages in occupational health and safety

    International Nuclear Information System (INIS)

    Burtraw, D.; Shefftz, J.

    1994-01-01

    This paper surveys the theoretical basis for the possibility that coal miner occupational health and safety damages are not adequately internalized into the production cost of mining coal and thereby impose an external cost on society

  16. Toward improved construction health, safety, and ergonomics in ...

    African Journals Online (AJOL)

    involved in architectural CPD programmes take 'upstream design ownership' and use the model as a ... health and safety (H&S), inclusive of construction ergonomics, the responsibility for ...... Santiago, Chile, 18-20 January. Rotterdam: CIB ...

  17. 77 FR 39743 - Federal Advisory Council on Occupational Safety and Health (FACOSH)

    Science.gov (United States)

    2012-07-05

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2012-0022] Federal Advisory Council on Occupational Safety and Health (FACOSH) AGENCY: Occupational Safety and Health... Occupational Safety and Health (FACOSH). SUMMARY: The Assistant Secretary of Labor for Occupational Safety and...

  18. 78 FR 54923 - Federal Advisory Council on Occupational Safety and Health

    Science.gov (United States)

    2013-09-06

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2013-0013] Federal Advisory Council on Occupational Safety and Health AGENCY: Occupational Safety and Health... Occupational Safety and Health (FACOSH). SUMMARY: The Assistant Secretary of Labor for Occupational Safety and...

  19. 76 FR 39902 - Federal Advisory Council on Occupational Safety and Health (FACOSH)

    Science.gov (United States)

    2011-07-07

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2011-0116] Federal Advisory Council on Occupational Safety and Health (FACOSH) AGENCY: Occupational Safety and Health... Occupational Safety and Health (FACOSH). SUMMARY: The Assistant Secretary of Labor for Occupational Safety and...

  20. Occupational safety and health in the food and drink industries.

    OpenAIRE

    Tomoda S

    1993-01-01

    Chapter 5 examines "Safety and health issues in respect of women workers in the food and drink industries". The paper provides information on the impact of technological progress in the sector; identifies the general hazards encountered; describes the injuries and diseases suffered by workers and concentrates on the most common approaches adopted for their prevention; and concludes by emphasizing the importance of adopting a tripartite approach to the solution of safety and health problems.

  1. SCIENTIFIC SCHOOL DEPARTAMENT OF WORKPLACE SAFETY AND HEALTH

    Directory of Open Access Journals (Sweden)

    KAPLENKO G. G.

    2016-10-01

    Full Text Available Department “workplace safety and health and ergonomics” was created in 1971 at DECI. According to the Order of the State Committee of National Education of USSR on July 9, 1990 443 and by the decision of the Scientific Council of Institute on May 28, 1991 was reorganized into the Department of workplace safety and health. Over the 45 years of its existence the department has come a long way in the formation of educational and scientific potentsial

  2. Health physics, safety and medical services report for 1989

    International Nuclear Information System (INIS)

    Burt, A.K.; Bird, R.W.

    1990-09-01

    The Health Physics, Safety and Medical Services Report for Harwell Laboratory for 1989 includes data on the monitoring of the working environment, personnel monitoring, radiological incidents, disposal of radioactive waste and protection of the public. Work on emergency planning, non-radiological health and safety, occupational hygiene, operations support is also discussed. Finally the medical services available and the medical examinations performed are described. (UK)

  3. Code of Sustainable Practice in Occupational and Environmental Health and Safety for Corporations.

    Science.gov (United States)

    Castleman, Barry; Allen, Barbara; Barca, Stefania; Bohme, Susanna Rankin; Henry, Emmanuel; Kaur, Amarjit; Massard-Guilbaud, Genvieve; Melling, Joseph; Menendez-Navarro, Alfredo; Renfrew, Daniel; Santiago, Myrna; Sellers, Christopher; Tweedale, Geoffrey; Zalik, Anna; Zavestoski, Stephen

    2008-01-01

    At a conference held at Stony Brook University in December 2007, "Dangerous Trade: Histories of Industrial Hazard across a Globalizing World," participants endorsed a Code of Sustainable Practice in Occupational and Environmental Health and Safety for Corporations. The Code outlines practices that would ensure corporations enact the highest health and environmentally protective measures in all the locations in which they operate. Corporations should observe international guidelines on occupational exposure to air contaminants, plant safety, air and water pollutant releases, hazardous waste disposal practices, remediation of polluted sites, public disclosure of toxic releases, product hazard labeling, sale of products for specific uses, storage and transport of toxic intermediates and products, corporate safety and health auditing, and corporate environmental auditing. Protective measures in all locations should be consonant with the most protective measures applied anywhere in the world, and should apply to the corporations' subsidiaries, contractors, suppliers, distributors, and licensees of technology. Key words: corporations, sustainability, environmental protection, occupational health, code of practice.

  4. Westinghouse Hanford Company health and safety performance report

    Energy Technology Data Exchange (ETDEWEB)

    Rogers, L.

    1996-05-15

    Topping the list of WHC Safety recognition during this reporting period is a commendation received from the National Safety Council (NSC). The NSC bestowed their Award of Honor upon WHC for significant reduction of incidence rates during CY 1995. The award is based upon a reduction of 48 % or greater in cases involving days away from work, a 30 % or greater reduction in the number of days away, and a 15% or greater reduction in the total number of occupational injuries and illnesses. (page 2-1). A DOE-HQ review team representing the Office of Envirorunent, Safety and Health (EH), visited the Hanford Site during several weeks of the quarter. Ile 40-member Safety Management Evaluation Team (SMET) assessed WHC in the areas of management responsibility, comprehensive requirements, and competence commensurate with responsibility. As part of their new approach to oversight, they focused on the existence of management systems and programs (comparable approach to VPP). Plant/project areas selected for review within WHC were PFP, B Plant/WESF, Tank Farms, and K-Basins (page 2-2). Effective safety meetings, prejob safety meetings, etc., are a cornerstone of any successful safety program. In an effort to improve the reporting of safety meetings, the Safety/Security Meeting Report form was revised. It now provides a mechanism for recording and tracking safety issues (page 2-4). WHC has experienced an increase in the occupational injury and illness incidence rates during the first quarter of CY 1996. Trends show this increase can be partially attributed to inattention to workplace activities due 0999to the uncertainty Hanford employees currently face with recent reduction of force, reorganization, and reengineering efforts (page 2-7). The cumulative CY 1995 lost/restricted workday case incidence rate for the first quarter of CY 1996 (1.28) is 25% below the DOE CY 1991-93 average (1.70). However, the incidence rate increased 24% from the CY 1995 rate of 1.03 (page 2-8). The

  5. Westinghouse Hanford Company health and safety performance report

    International Nuclear Information System (INIS)

    Rogers, L.

    1996-01-01

    Topping the list of WHC Safety recognition during this reporting period is a commendation received from the National Safety Council (NSC). The NSC bestowed their Award of Honor upon WHC for significant reduction of incidence rates during CY 1995. The award is based upon a reduction of 48 % or greater in cases involving days away from work, a 30 % or greater reduction in the number of days away, and a 15% or greater reduction in the total number of occupational injuries and illnesses. (page 2-1). A DOE-HQ review team representing the Office of Envirorunent, Safety and Health (EH), visited the Hanford Site during several weeks of the quarter. Ile 40-member Safety Management Evaluation Team (SMET) assessed WHC in the areas of management responsibility, comprehensive requirements, and competence commensurate with responsibility. As part of their new approach to oversight, they focused on the existence of management systems and programs (comparable approach to VPP). Plant/project areas selected for review within WHC were PFP, B Plant/WESF, Tank Farms, and K-Basins (page 2-2). Effective safety meetings, prejob safety meetings, etc., are a cornerstone of any successful safety program. In an effort to improve the reporting of safety meetings, the Safety/Security Meeting Report form was revised. It now provides a mechanism for recording and tracking safety issues (page 2-4). WHC has experienced an increase in the occupational injury and illness incidence rates during the first quarter of CY 1996. Trends show this increase can be partially attributed to inattention to workplace activities due 0999to the uncertainty Hanford employees currently face with recent reduction of force, reorganization, and reengineering efforts (page 2-7). The cumulative CY 1995 lost/restricted workday case incidence rate for the first quarter of CY 1996 (1.28) is 25% below the DOE CY 1991-93 average (1.70). However, the incidence rate increased 24% from the CY 1995 rate of 1.03 (page 2-8). The

  6. Identifying research priorities for patient safety in mental health: an international expert Delphi study

    Science.gov (United States)

    Murray, Kevin; Thibaut, Bethan; Ramtale, Sonny Christian; Adam, Sheila; Darzi, Ara; Archer, Stephanie

    2018-01-01

    Objective Physical healthcare has dominated the patient safety field; research in mental healthcare is not as extensive but findings from physical healthcare cannot be applied to mental healthcare because it delivers specialised care that faces unique challenges. Therefore, a clearer focus and recognition of patient safety in mental health as a distinct research area is still needed. The study aim is to identify future research priorities in the field of patient safety in mental health. Design Semistructured interviews were conducted with the experts to ascertain their views on research priorities in patient safety in mental health. A three-round online Delphi study was used to ascertain consensus on 117 research priority statements. Setting and participants Academic and service user experts from the USA, UK, Switzerland, Netherlands, Ireland, Denmark, Finland, Germany, Sweden, Australia, New Zealand and Singapore were included. Main outcome measures Agreement in research priorities on a five-point scale. Results Seventy-nine statements achieved consensus (>70%). Three out of the top six research priorities were patient driven; experts agreed that understanding the patient perspective on safety planning, on self-harm and on medication was important. Conclusions This is the first international Delphi study to identify research priorities in safety in the mental field as determined by expert academic and service user perspectives. A reasonable consensus was obtained from international perspectives on future research priorities in patient safety in mental health; however, the patient perspective on their mental healthcare is a priority. The research agenda for patient safety in mental health identified here should be informed by patient safety science more broadly and used to further establish this area as a priority in its own right. The safety of mental health patients must have parity with that of physical health patients to achieve this. PMID:29502096

  7. Perceived School Safety is Strongly Associated with Adolescent Mental Health Problems

    NARCIS (Netherlands)

    Nijs, Miesje M.; Bun, Clothilde J. E.; Tempelaar, Wanda M.; de Wit, Niek J.; Burger, Huibert; Plevier, Carolien M.; Boks, Marco P. M.

    School environment is an important determinant of psychosocial function and may also be related to mental health. We therefore investigated whether perceived school safety, a simple measure of this environment, is related to mental health problems. In a population-based sample of 11,130 secondary

  8. Key Element Performance In Occupational Safety And Health Management System In Organization (A Literature

    Directory of Open Access Journals (Sweden)

    Agus Salim Nuzaihan Aras

    2016-01-01

    Full Text Available Setting an effective safety and health management system is crucial in order to reduce problem relating to accident and ill in management organizational. It is involve with multiple level of management and stakeholders who empower the organization to the management in handling the safety and health cases and issues in organizational. It is necessary to prepare a well knowledge about safety and health management systems and preparing the framework for setting a certain scale in measuring its performance in this area. The successful or failure of management does showing the capability of the organization in delivering the responsible to management levels [1]. The problem in safe work issues and practices cause by the management commitment and involvement that create improper safety program and procedures, and this crisis keep continuing till present [2]. This paper describes about key element of safety and health management system and measuring the performance in order to get an effective management system in organization that describes the process in achieving effectiveness in management. The literature review will be conducted through the data collection from research findings and defined the strong character of key element in which focusing on measuring performance. A guide on key element performance in occupational safety and health management system is specifically drawn to prepare for a future research.

  9. Managing health and safety risks: Implications for tailoring health and safety management system practices.

    Science.gov (United States)

    Willmer, D R; Haas, E J

    2016-01-01

    As national and international health and safety management system (HSMS) standards are voluntarily accepted or regulated into practice, organizations are making an effort to modify and integrate strategic elements of a connected management system into their daily risk management practices. In high-risk industries such as mining, that effort takes on added importance. The mining industry has long recognized the importance of a more integrated approach to recognizing and responding to site-specific risks, encouraging the adoption of a risk-based management framework. Recently, the U.S. National Mining Association led the development of an industry-specific HSMS built on the strategic frameworks of ANSI: Z10, OHSAS 18001, The American Chemistry Council's Responsible Care, and ILO-OSH 2001. All of these standards provide strategic guidance and focus on how to incorporate a plan-do-check-act cycle into the identification, management and evaluation of worksite risks. This paper details an exploratory study into whether practices associated with executing a risk-based management framework are visible through the actions of an organization's site-level management of health and safety risks. The results of this study show ways that site-level leaders manage day-to-day risk at their operations that can be characterized according to practices associated with a risk-based management framework. Having tangible operational examples of day-to-day risk management can serve as a starting point for evaluating field-level risk assessment efforts and their alignment to overall company efforts at effective risk mitigation through a HSMS or other processes.

  10. World Day for Safety and Health at Work

    CERN Multimedia

    2012-01-01

    27 April is World Day for Safety and Health at Work.   CERN’s health and safety teams look forward to seeing you at their stands in each of the three restaurants. This year, we cast the spotlight on two topics: • ergonomics • electrical hazards. Come and get tips that will help you to ensure your safety and to stay healthy and, you never know, you might be lucky enough to win a nice prize. Don't forget, Friday, 27 April 2012 from 11:30 a.m. to 2:30 p.m. in your nearest restaurant!

  11. A model for managing cold-related health and safety risks at workplaces.

    Science.gov (United States)

    Risikko, Tanja; Mäkinen, Tiina M; Påsche, Arvid; Toivonen, Liisa; Hassi, Juhani

    2003-05-01

    Cold conditions increase health and safety risks at work in several ways. The effects of cold have not been sufficiently taken into consideration in occupational safety and health practices. A systematic model and methods were developed for managing cold-related health and safety risks at workplaces. The development work was performed, in a context-bound manner, in pilot industries and workplaces. The model can be integrated into the company's occupational health and safety management system, such as OHSAS 18001. The cold risks are identified and assessed by using a checklist. The preventive measures are systematically planned in a written form specifically produced for cold workplaces. It includes the organisational and technical preventive measures, protective clothing and personal protective equipment, as well as training and information of the personnel. According to the model, all the workers, foremen, occupational safety personnel and occupational health care personnel are trained to recognise the cold risks and to conduct preventive actions. The developed model was evaluated in the context of cold outdoor (construction) and indoor work (fish processing), and by occupational health and safety professionals. According to the feedback, the model and methods were easy to use after a one-day introduction session. The continuum between the cold risk assessment and management worked well, although there was some overlap in the documentation. The cold risk management model and its methods form an essential part of ISO CD 15743 Strategy for risk assessment, management and work practice in cold environments.

  12. Safety, health and environmental committee (JKSHE): Establishing chemical hazard management

    International Nuclear Information System (INIS)

    Shyen, A.K.S.; Noriah Mod Ali; Sangau, J.K.

    2012-01-01

    Most of the laboratories in Malaysian Nuclear Agency are using chemicals in their research activities. However, it is known that using of chemicals without proper knowledge especially on the material characteristics as well as safe handling procedure may cause great harm to the workers. Therefore, Safety, Health and Environmental Committee (JKSHE) sees the need to establish a good chemical hazard management to ensure that a safe and healthy workplace and environment is provided. One of the elements in chemical hazard management is to carry out Chemical Hazard Risk Assessment (CHRA). The assessment was done so that decision can be made on suitable control measures upon use of such chemicals, such as induction and training courses to be given to the workers and health surveillance activities that may be needed to protect the workers. For this, JKSHE has recommended to conduct CHRA for one of the laboratories at Secondary Standard Dosimetry Laboratory (SSDL) namely Film Dosimeter Processing Room (dark room) as the initial effort towards a better chemical hazard management. This paper presents the case study where CHRA was conducted to identify the chemical hazards at the selected laboratory, the adequacy of existing control measures and finally the recommendation for more effective control measures. (author)

  13. [B-BS and occupational health and safety management systems].

    Science.gov (United States)

    Bacchetta, Adriano Paolo

    2010-01-01

    The objective of a SGSL is the "prevention" agreement as approach of "pro-active" toward the safety at work through the construction of an integrated managerial system in synergic an dynamic way with the business organization, according to continuous improvement principles. Nevertheless the adoption of a SGSL, not could guarantee by itself the obtainment of the full effectiveness than projected and every individual's adhesion to it, must guarantee it's personal involvement in proactive way, so that to succeed to actual really how much hypothesized to systemic level to increase the safety in firm. The objective of a behavioral safety process that comes to be integrated in a SGSL, it has the purpose to succeed in implementing in firm a process of cultural change that raises the workers social group fundamental safety value, producing an ample and full involvement of all in the activities of safety at work development. SGSL = Occupational Health and Safety Management System.

  14. A new standard for multidisciplinary health and safety technicians

    Energy Technology Data Exchange (ETDEWEB)

    Trinoskey, P.A.; Fry, L.A. [Lawrence Livermore National Laboratory, Univ. of California, CA (United States); Egbert, W.F. [Lawrence Livermore National Laboratory, Allied Signal Technical Corporation (United States)

    2000-05-01

    Over the last two decades, a significant trend in health and safety has been toward greater specialization. However, compartmentalization of health and safety disciplines often leads to an inequity in resources, especially when appropriations overemphasize one risk to the detriment of others. For example, overemphasis on radiological safety can create an imbalance in overall worker protection. A multidisciplinary technical can help restore the balance and provide for a healthier and safer work environment. The key advantages of a multidisciplinary health and safety technician include: Broad coverage of the work area by one technician, More diverse use of the technician pool, Better coverage for off-shift or nonstandard hours, Balance of risks because all hazards are considered, Integrated emergency response, Ownership, Less time of identify the correct person with the requisite skills. We have developed a new standard that establishes the training and related qualifications for a multidisciplinary health and safety technician. The areas of training and qualification that are addressed include elements of industrial hygiene, industrial safety, fire protection, electrical safety, construction safety, and radiation safety. The initial core training program ensures that individuals are trained to the performance of requirements of the job. Initial training is in five areas: Fundamentals, Hazard recognition, Hazard assessment, Hazards controls, Hazards minimization. Core training is followed by formal qualification on specific tasks, including ventilation surveys, air monitoring, noise assessments, radiological monitoring, area inspections, work-area setups, and work coverage. The new standard addresses not only training topics and requirements, but also guidance to ensure that performance objectives are met. The standard applies to technicians, supervisors, technologists, and six specialty areas, including academic institutions and decontamination and decommissioning

  15. A new standard for multidisciplinary health and safety technicians

    International Nuclear Information System (INIS)

    Trinoskey, P.A.; Fry, L.A.; Egbert, W.F.

    2000-01-01

    Over the last two decades, a significant trend in health and safety has been toward greater specialization. However, compartmentalization of health and safety disciplines often leads to an inequity in resources, especially when appropriations overemphasize one risk to the detriment of others. For example, overemphasis on radiological safety can create an imbalance in overall worker protection. A multidisciplinary technical can help restore the balance and provide for a healthier and safer work environment. The key advantages of a multidisciplinary health and safety technician include: Broad coverage of the work area by one technician, More diverse use of the technician pool, Better coverage for off-shift or nonstandard hours, Balance of risks because all hazards are considered, Integrated emergency response, Ownership, Less time of identify the correct person with the requisite skills. We have developed a new standard that establishes the training and related qualifications for a multidisciplinary health and safety technician. The areas of training and qualification that are addressed include elements of industrial hygiene, industrial safety, fire protection, electrical safety, construction safety, and radiation safety. The initial core training program ensures that individuals are trained to the performance of requirements of the job. Initial training is in five areas: Fundamentals, Hazard recognition, Hazard assessment, Hazards controls, Hazards minimization. Core training is followed by formal qualification on specific tasks, including ventilation surveys, air monitoring, noise assessments, radiological monitoring, area inspections, work-area setups, and work coverage. The new standard addresses not only training topics and requirements, but also guidance to ensure that performance objectives are met. The standard applies to technicians, supervisors, technologists, and six specialty areas, including academic institutions and decontamination and decommissioning

  16. Urgent Safety Measures in Japan after Great East Japan Earthquake

    International Nuclear Information System (INIS)

    Taniura, Wataru; Otani, Hiroyasu

    2012-01-01

    Due to tsunami triggered by the Great East Japan Earthquake, the operating and refueling reactor facilities at Fukushima Dai-ichi and Dai-ni Nuclear Power Plants caused a nuclear hazard. Given the fact, Japanese electric power companies voluntarily began to compile various urgent measures against tsunami. And then the Nuclear and Industrial Safety Agency (NISA) ordered the licensees to put into practice the voluntarily compiled urgent safety measures, in order to ensure the effectiveness of the means for recovering cooling functions along with avoiding the release of radioactive substances to the possible minimum, even if a huge tsunami following a severe earthquake hits nuclear power plants. The following describes the state and the effect of the urgent safety measures implemented for 44 reactors (under operation) and 1 reactor (under construction) in Japan and also describes the measures to be implemented by the licensees of reactor operation in the future.

  17. Accounting software cost management on health and safety, legal framework and areas of improvement

    Directory of Open Access Journals (Sweden)

    K.I. Samchuk

    2017-03-01

    Full Text Available Awareness of human life and health as the highest value is a sign of a civilized society. The economic activity of enterprises accompanied the influence of dangerous and harmful factors. An urgent need for society development and European integration is to create an effective mechanism by which the whole complex will be implemented measures to create conditions that meet the health care workers. The article highlighted media mouthpieces and performers interests of occupational safety, responsibilities entities regarding safety, the place and importance of your support in the management of safety measures, the necessity and directions of its improvement. Improving your security management costs of safety measures based on the determination of the legal framework, which aims to provide legal protection for employees, agencies and organizations, entities in the relationship work.

  18. Opportunities for health and safety professionals in environmental restoration work

    International Nuclear Information System (INIS)

    Norris, A.E.

    1991-01-01

    The safety of workers in waste management and in environmental restoration work is regulated in large part by the Occupational Safety and Health Administration (OSHA). Many of the OSHA rules are given in Part 1910, Occupational Safety and Health Standards, of Title 29 of the Code of Federal Regulations (CFR). Section 120 of 29 CFR 1910 specifically addresses hazardous waste operations and emergency response operations. The remainder of this discussion focuses on clean-up operations. The purpose of this paper is to review areas of employment opportunity in environmental restoration work for health and safety professionals. Safety and health risk analyses are mentioned as one area of opportunity, and these analyses are required by the standards. Site safety and health supervisors will be needed during field operations. Those who enjoy teaching might consider helping to meet the training needs that are mandated. Finally, engineering help both to separate workers from hazards and to improve personal protective equipment, when it must be worn, would benefit those actively involved in environmental restoration activities

  19. 75 FR 13783 - Maritime Advisory Committee for Occupational Safety and Health (MACOSH)

    Science.gov (United States)

    2010-03-23

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration Maritime Advisory Committee for Occupational Safety and Health (MACOSH) AGENCY: Occupational Safety and Health Administration (OSHA), Labor... Health (MACOSH) was established under Section 7 of the Occupational Safety and Health (OSH) Act of 1970...

  20. Economic evaluation of safety measures for transport companies

    NARCIS (Netherlands)

    Rietveld, Piet; Rienstra, Sytze A.

    1998-01-01

    Measures to reduce material damage within companies may both increase the business economic performance of the company and traffic safety in general. In this paper the notion of whether such measures are economically feasible is investigated. Results are presented of a series of interviews

  1. NIF special equipment construction health and safety plan

    Energy Technology Data Exchange (ETDEWEB)

    Sawicki, R.H.

    1997-07-28

    The purpose of this plan is to identify how the construction and deployment activities of the National Ignition Facility (NIF) Special Equipment (SE) will be safely executed. This plan includes an identification of (1) the safety-related responsibilities of the SE people and their interaction with other organizations involved; (2) safety related requirements, policies, and documentation; (3) a list of the potential hazards unique to SE systems and the mechanisms that will be implemented to control them to acceptable levels; (4) a summary of Environmental Safety and Health (ES&H) training requirements; and (5) requirements of contractor safety plans that will be developed and used by all SE contractors participating in site activities. This plan is a subsidiary document to the NIF Construction Safety Program (CSP) and is intended to compliment the requirements stated therein with additional details specific to the safety needs of the SE construction-related activities. If a conflict arises between these two documents, the CSP will supersede. It is important to note that this plan does not list all of the potential hazards and their controls because the design and safety analysis process is still ongoing. Additional safety issues win be addressed in the Final Safety Analysis Report, Operational Safety Procedures (OSPs), and other plans and procedures as described in Section 3.0 of this plan.

  2. NIF special equipment construction health and safety plan

    International Nuclear Information System (INIS)

    Sawicki, R.H.

    1997-01-01

    The purpose of this plan is to identify how the construction and deployment activities of the National Ignition Facility (NIF) Special Equipment (SE) will be safely executed. This plan includes an identification of (1) the safety-related responsibilities of the SE people and their interaction with other organizations involved; (2) safety related requirements, policies, and documentation; (3) a list of the potential hazards unique to SE systems and the mechanisms that will be implemented to control them to acceptable levels; (4) a summary of Environmental Safety and Health (ES ampersand H) training requirements; and (5) requirements of contractor safety plans that will be developed and used by all SE contractors participating in site activities. This plan is a subsidiary document to the NIF Construction Safety Program (CSP) and is intended to compliment the requirements stated therein with additional details specific to the safety needs of the SE construction-related activities. If a conflict arises between these two documents, the CSP will supersede. It is important to note that this plan does not list all of the potential hazards and their controls because the design and safety analysis process is still ongoing. Additional safety issues win be addressed in the Final Safety Analysis Report, Operational Safety Procedures (OSPs), and other plans and procedures as described in Section 3.0 of this plan

  3. Keeping nurse researchers safe: workplace health and safety issues.

    Science.gov (United States)

    Barr, Jennieffer; Welch, Anthony

    2012-07-01

    This article is a report of a qualitative study of workplace health and safety issues in nursing research. Researcher health and safety have become increasing concerns as there is an increased amount of research undertaken in the community and yet there is a lack of appropriate guidelines on how to keep researchers safe when undertaking fieldwork. This study employed a descriptive qualitative approach, using different sources of data to find any references to researcher health and safety issues. A simple descriptive approach to inquiry was used for this study. Three approaches to data collection were used: interviews with 15 researchers, audits of 18 ethics applications, and exploration of the literature between 1992 and 2010 for examples of researcher safety issues. Data analysis from the three approaches identified participant comments, narrative descriptions or statements focused on researcher health and safety. Nurse researchers' health and safety may be at risk when conducting research in the community. Particular concern involves conducting sensitive research where researchers are physically at risk of being harmed, or being exposed to the development of somatic symptoms. Nurse researchers may perceive the level of risk of harm as lower than the actual or potential harm present in research. Nurse researchers do not consistently implement risk assessment before and during research. Researcher health and safety should be carefully considered at all stages of the research process. Research focusing on sensitive data and vulnerable populations need to consider risk minimization through strategies such as appropriate researcher preparation, safety during data collection, and debriefing if required. © 2012 Blackwell Publishing Ltd.

  4. Patient safety goals for the proposed Federal Health Information Technology Safety Center.

    Science.gov (United States)

    Sittig, Dean F; Classen, David C; Singh, Hardeep

    2015-03-01

    The Office of the National Coordinator for Health Information Technology is expected to oversee creation of a Health Information Technology (HIT) Safety Center. While its functions are still being defined, the center is envisioned as a public-private entity focusing on promotion of HIT related patient safety. We propose that the HIT Safety Center leverages its unique position to work with key administrative and policy stakeholders, healthcare organizations (HCOs), and HIT vendors to achieve four goals: (1) facilitate creation of a nationwide 'post-marketing' surveillance system to monitor HIT related safety events; (2) develop methods and governance structures to support investigation of major HIT related safety events; (3) create the infrastructure and methods needed to carry out random assessments of HIT related safety in complex HCOs; and (4) advocate for HIT safety with government and private entities. The convening ability of a federally supported HIT Safety Center could be critically important to our transformation to a safe and effective HIT enabled healthcare system. © The Author 2014. Published by Oxford University Press on behalf of the American Medical Informatics Association. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  5. Getting home safe and sound: occupational safety and health administration at 38.

    Science.gov (United States)

    Silverstein, Michael

    2008-03-01

    The Occupational Safety and Health Act of 1970 (OSHAct) declared that every worker is entitled to safe and healthful working conditions, and that employers are responsible for work being free from all recognized hazards. Thirty-eight years after these assurances, however, it is difficult to find anyone who believes the promise of the OSHAct has been met. The persistence of preventable, life-threatening hazards at work is a failure to keep a national promise. I review the history of the Occupational Safety and Health Administration and propose measures to better ensure that those who go to work every day return home safe and sound. These measures fall into 6 areas: leverage and accountability, safety and health systems, employee rights, equal protection, framing, and infrastructure.

  6. SAFETY

    CERN Multimedia

    Niels Dupont

    2013-01-01

    CERN Safety rules and Radiation Protection at CMS The CERN Safety rules are defined by the Occupational Health & Safety and Environmental Protection Unit (HSE Unit), CERN’s institutional authority and central Safety organ attached to the Director General. In particular the Radiation Protection group (DGS-RP1) ensures that personnel on the CERN sites and the public are protected from potentially harmful effects of ionising radiation linked to CERN activities. The RP Group fulfils its mandate in collaboration with the CERN departments owning or operating sources of ionising radiation and having the responsibility for Radiation Safety of these sources. The specific responsibilities concerning "Radiation Safety" and "Radiation Protection" are delegated as follows: Radiation Safety is the responsibility of every CERN Department owning radiation sources or using radiation sources put at its disposition. These Departments are in charge of implementing the requi...

  7. Speaking Plainly: Communicating the Patient's Role in Health Care Safety

    National Research Council Canada - National Science Library

    Miranda, David J; Zeller, Paula K; Lee, Rosemary; Koepke, Christopher P; Holland, Howard E; Englert, Farah; Swift, Elaine K

    2005-01-01

    ... patients reduce health care system errors and improve the safety of their care. The basis for the fact sheet was a larger set of messages drawn from a review of the health care literature by the Agency for Healthcare Research and Quality...

  8. Impact of organisational characteristics on health and safety ...

    African Journals Online (AJOL)

    The construction industry makes a contribution to occupational accidents and ill health records in Nigeria. This study was designed to evaluate the impact of organisational characteristics on health and safety (H&S) management practices of Nigerian small and medium-sized construction enterprises (SMEs). The study ...

  9. Whistleblowing on health, welfare and safety: the UK experience.

    Science.gov (United States)

    Vinten, Gerald; Gavin, Thomas A

    2005-01-01

    This article takes a look at how whistleblowing has changed over the last 25 years highlighting some well-known cases and focusing on the areas of health and safety, health services and social services. The article also covers government legislation and the lead taken by professional bodies to encourage and support whistleblowers.

  10. Ecological Issues Related to Children's Health and Safety

    Science.gov (United States)

    Aldridge, Jerry; Kohler, Maxie

    2009-01-01

    Issues concerning the health and safety of children and youth occur at multiple levels. Bronfenbrenner (1995) proposed an ecological systems approach in which multiple systems interact to enhance or diminish children's development. The same systems are at work in health promotion. The authors present and review articles that reflect the multiple…

  11. Occupational Health and Safety in Ethiopia: A review of Situational ...

    African Journals Online (AJOL)

    The organization of occupational health and safety services is not yet resilient enough to handle the growing demands for workers' health in the context of industrialization. ... Commonly observed hazards in the workplace include occupational noise and ... Exposure to dust in textile and cement factories greatly exceeded ...

  12. K-effective as a measure of criticality safety

    International Nuclear Information System (INIS)

    Venner, J.; Haley, R.M.; Bowden, R.L.

    2003-01-01

    This paper considers the relation between the neutron multiplication of a system, k-effective, and critical parameters. It aims to investigate whether k-effective is always the most appropriate measure of safety. For simple systems handbook data can be effectively utilized, applying a safety factor to critical masses. In such situations, the criticality safety margin is readily apparent. However, more complex systems may use the calculated value of neutron multiplication to assess the criticality safety of the system under investigation. A problem arises because there is no exact consistency between k-effective and the physical margin of subcriticality, in terms of parameters such as mass. In the UK, commonly accepted safety criteria are applied to limit the k-effective of the system being assessed. These margins of subcriticality have no definitive justification to support the values chosen and might be considered rather arbitrary in nature. This paper aims to answer this question of suitability by investigating the relation between k-effective and the physical critical parameters for a wide range of systems. It concludes that the safety criteria currently applied in the UK are valid, but some difference exists between safety factors applied to the mass of fissile material present and the corresponding value of k-effective. (author)

  13. Promoting health and safety for traveling and commuting employees.

    Science.gov (United States)

    Pochat-Debroux, Sophia

    2008-09-01

    In a society that relies on a growing market economy and free enterprise, Americans spend inordinate time commuting and traveling for work. Aircraft and private vehicles are the two primary modes of work-related travel, with each having its own inherit risks and hazards. Although much has been written about international travel health, little has been published about protecting the health and safety of workers during domestic business travel. The intent of this article is to highlight the statistics associated with domestic business travel and present sound rationale for an inclusive and comprehensive domestic travel health and safety program for employees.

  14. Health and safety implications of occupational exposure to engineered nanomaterials.

    Science.gov (United States)

    Stebounova, Larissa V; Morgan, Hallie; Grassian, Vicki H; Brenner, Sara

    2012-01-01

    The rapid growth and commercialization of nanotechnology are currently outpacing health and safety recommendations for engineered nanomaterials. As the production and use of nanomaterials increase, so does the possibility that there will be exposure of workers and the public to these materials. This review provides a summary of current research and regulatory efforts related to occupational exposure and medical surveillance for the nanotechnology workforce, focusing on the most prevalent industrial nanomaterials currently moving through the research, development, and manufacturing pipelines. Their applications and usage precedes a discussion of occupational health and safety efforts, including exposure assessment, occupational health surveillance, and regulatory considerations for these nanomaterials. Copyright © 2011 Wiley Periodicals, Inc.

  15. Measures taken by the French Health Minister to ensure safety in radiotherapy treatments;Les mesures prises par la Ministre de la Sante pour assurer la securite des traitements en radiotherapie

    Energy Technology Data Exchange (ETDEWEB)

    Bachelot-Narquin, R. [Ministre de la Sante et des Sports, 75 - Paris (France)

    2009-12-15

    The objective of these measures is to restore the confidence of patients and professionals in an essential practice for the treatment of cancers and that is in constant progression. 70% of patients suffering of a cancer receive every year a radiotherapy. The national measures aim to strengthen the safety of practice, the quality of cares, the vigilance on the unwanted effects. among the measures we find in vivo dosimetry, doubling of radio physicists and then pass from 300 radio physicists in 2007 to 600 in 2012. (N.C.)

  16. Translating Health Services Research into Practice in the Safety Net.

    Science.gov (United States)

    Moore, Susan L; Fischer, Ilana; Havranek, Edward P

    2016-02-01

    To summarize research relating to health services research translation in the safety net through analysis of the literature and case study of a safety net system. Literature review and key informant interviews at an integrated safety net hospital. This paper describes the results of a comprehensive literature review of translational science literature as applied to health care paired with qualitative analysis of five key informant interviews conducted with senior-level management at Denver Health and Hospital Authority. Results from the literature suggest that implementing innovation may be more difficult in the safety net due to multiple factors, including financial and organizational constraints. Results from key informant interviews confirmed the reality of financial barriers to innovation implementation but also implied that factors, including institutional respect for data, organizational attitudes, and leadership support, could compensate for disadvantages. Translating research into practice is of critical importance to safety net providers, which are under increased pressure to improve patient care and satisfaction. Results suggest that translational research done in the safety net can better illuminate the special challenges of this setting; more such research is needed. © Health Research and Educational Trust.

  17. Measuring School Climate in High Schools: A Focus on Safety, Engagement, and the Environment

    Science.gov (United States)

    Bradshaw, Catherine P.; Waasdorp, Tracy E.; Debnam, Katrina J.; Johnson, Sarah Lindstrom

    2014-01-01

    Background: School climate has been linked to multiple student behavioral, academic, health, and social-emotional outcomes. The US Department of Education (USDOE) developed a 3-factor model of school climate comprised of safety, engagement, and environment. This article examines the factor structure and measurement invariance of the USDOE model.…

  18. Occupational Health and Safety and Organizational Commitment: Evidence from the Ghanaian Mining Industry.

    Science.gov (United States)

    Amponsah-Tawiah, Kwesi; Mensah, Justice

    2016-09-01

    This study seeks to examine the relationship and impact of occupational health and safety on employees' organizational commitment in Ghana's mining industry. The study explores occupational health and safety and the different dimensions of organizational commitment. A cross-sectional survey design was used for this study. The respondents were selected based on simple random sampling. Out of 400 questionnaires administered, 370 were returned (77.3% male and 22.7% female) and used for the study. Correlation and multiple regression analysis were used to determine the relationship and impact between the variables. The findings of this study revealed positive and significant relationship between occupational health and safety management, and affective, normative, and continuance commitment. Additionally, the results revealed the significant impact of occupational health and safety on affective, normative, and continuance commitment. Management within the mining sector of Ghana must recognize the fact that workers who feel healthy and safe in the performance of their duties, develop emotional attachment and have a sense of obligation to their organization and are most likely committed to the organization. Employees do not just become committed to the organization; rather, they expect management to first think about their health and safety needs by instituting good and sound policy measures. Thus, management should invest in the protection of employees' health and safety in organizations.

  19. Studying the Safety Impact of Autonomous Vehicles Using Simulation-Based Surrogate Safety Measures

    Directory of Open Access Journals (Sweden)

    Mark Mario Morando

    2018-01-01

    Full Text Available Autonomous vehicle (AV technology has advanced rapidly in recent years with some automated features already available in vehicles on the market. AVs are expected to reduce traffic crashes as the majority of crashes are related to driver errors, fatigue, alcohol, or drugs. However, very little research has been conducted to estimate the safety impact of AVs. This paper aims to investigate the safety impacts of AVs using a simulation-based surrogate safety measure approach. To this end, safety impacts are explored through the number of conflicts extracted from the VISSIM traffic microsimulator using the Surrogate Safety Assessment Model (SSAM. Behaviours of human-driven vehicles (HVs and AVs (level 4 automation are modelled within the VISSIM’s car-following model. The safety investigation is conducted for two case studies, that is, a signalised intersection and a roundabout, under various AV penetration rates. Results suggest that AVs improve safety significantly with high penetration rates, even when they travel with shorter headways to improve road capacity and reduce delay. For the signalised intersection, AVs reduce the number of conflicts by 20% to 65% with the AV penetration rates of between 50% and 100% (statistically significant at p<0.05. For the roundabout, the number of conflicts is reduced by 29% to 64% with the 100% AV penetration rate (statistically significant at p<0.05.

  20. A Global Perspective on Vaccine Safety and Public Health: The Global Advisory Committee on Vaccine Safety

    Science.gov (United States)

    Folb, Peter I.; Bernatowska, Ewa; Chen, Robert; Clemens, John; Dodoo, Alex N. O.; Ellenberg, Susan S.; Farrington, C. Patrick; John, T. Jacob; Lambert, Paul-Henri; MacDonald, Noni E.; Miller, Elizabeth; Salisbury, David; Schmitt, Heinz-J.; Siegrist, Claire-Anne; Wimalaratne, Omala

    2004-01-01

    Established in 1999, the Global Advisory Committee on Vaccine Safety advises the World Health Organization (WHO) on vaccine-related safety issues and enables WHO to respond promptly, efficiently, and with scientific rigor to issues of vaccine safety with potential global importance. The committee also assesses the implications of vaccine safety for practice worldwide and for WHO policies. We describe the principles on which the committee was established, its modus operandi, and the scope of the work undertaken, both present and future. We highlight its recent recommendations on major issues, including the purported link between the measles–mumps–rubella vaccine and autism and the safety of the mumps, influenza, yellow fever, BCG, and smallpox vaccines as well as that of thiomersal-containing vaccines. PMID:15514229

  1. United States import safety, environmental health, and food safety regulation in China.

    Science.gov (United States)

    Nyambok, Edward O; Kastner, Justin J

    2012-01-01

    China boasts a rapidly growing economy and is a leading food exporter. Since China has dominated world export markets in food, electronics, and toys, many safety concerns about Chinese exports have emerged. For example, many countries have had problems with Chinese food products and food-processing ingredients. Factors behind food safety and environmental health problems in China include poor industrial waste management, the use of counterfeit agricultural inputs, inadequate training of farmers on good farm management practices, and weak food safety laws and poor enforcement. In the face of rising import safety problems, the U.S. is now requiring certification of products and foreign importers, pursuing providing incentives to importers who uphold good safety practices, and considering publicizing the names of certified importers.

  2. [History of occupational health physician and industrial safety and health law].

    Science.gov (United States)

    Horie, Seichi

    2013-10-01

    In Japan, an employer of a workplace with 50 or more employees is legally required to assign an occupational health physician. The assignment rate in 2010 was reported as 87.0%. This policy started with the provision of "factory physician"in the Factory Law in 1938, then the Labour Standard Law stipulated "physician hygienist" in 1947, and finally the Industrial Safety and Health Law defined "occupational health physician" in 1972. In 1996, a revision of the law then required those physicians to complete training courses in occupational medicine, as designated by an ordinance. Historically, an on-site physician was expected to cure injuries and to prevent communicable diseases of factory workers. The means of occupational hygienic management by working environment measurements, etc., and of health management by health examinations, etc., were developed. Localized exhaust ventilation and personal protection equipment became widely utilized. Qualification systems for non-medical experts in occupational hygiene were structured, and relationships between employers and occupational health physicians were stipulated in the legislative documents. Currently, the Japan Medical Association and the University of Occupational and Environmental Health, Japan educate and train occupational health physicians, and the Japan Society for Occupational Health maintains a specialized board certification system for these physicians. In the future, additional efforts should be made to strengthen the expertise of occupational health physicians, to define and recognize the roles of non-medical experts in occupational hygiene, to incorporate occupational health services in small enterprises, to promote occupational health risk assessment in the workplace, and to reorganize the current legislation, amended repeatedly over the decades.

  3. Annual health, safety and environmental performance report for 1992

    International Nuclear Information System (INIS)

    Orman, R.F.; Richards, S.

    1993-12-01

    This report summarizes the safety and environmental record of the operations of Atomic Energy of Canada Limited (AECL) during 1992. An introduction highlights the results and describes the facilities and organizational systems. Subsequent sections indicate the performance of the company with respect to personnel radiation exposures, occupational injuries, the handling of wastes and the release of materials into the environment. Programs in health, safety and environmental protection are presented, along with site remediation and emergency preparedness practices

  4. Annual health, safety and environmental performance report for 1992

    International Nuclear Information System (INIS)

    Orman, R.F.; Richards, S.

    1993-12-01

    This report summarizes the safety and environmental record of the operations of Atomic Energy of Canada Limited (AECL) during 1992. an introduction highlights the results and describes the facilities and organizational systems. Subsequent sections indicate the performance of the company with respect to personnel radiation exposures, occupational injuries, the handling of wastes and the release of materials into the environment. Programs in health, safety and environmental protection are presented, along with site remediation and emergency preparedness practices

  5. Health safety issues of synthetic food colorants.

    Science.gov (United States)

    Amchova, Petra; Kotolova, Hana; Ruda-Kucerova, Jana

    2015-12-01

    Increasing attention has been recently paid to the toxicity of additives used in food. The European Parliament and the Council published the REGULATION (EC) No. 1333/2008 on food additives establishing that the toxicity of food additives evaluated before 20th January 2009 must be re-evaluated by European Food Safety Authority (EFSA). The aim of this review is to survey current knowledge specifically on the toxicity issues of synthetic food colorants using official reports published by the EFSA and other available studies published since the respective report. Synthetic colorants described are Tartrazine, Quinoline Yellow, Sunset Yellow, Azorubine, Ponceau 4R, Erythrosine, Allura Red, Patent Blue, Indigo Carmine, Brilliant Blue FCF, Green S, Brilliant Black and Brown HT. Moreover, a summary of evidence on possible detrimental effects of colorant mixes on children's behaviour is provided and future research directions are outlined. Copyright © 2015 Elsevier Inc. All rights reserved.

  6. Examining occupational health and safety vulnerability among Canadian workers with disabilities.

    Science.gov (United States)

    Breslin, F Curtis; Lay, A Morgan; Jetha, Arif; Smith, Peter

    2017-05-26

    To compare workers with and without disabilities on their reported workplace hazard exposure and the presence of occupational health and safety vulnerability factors. Working-aged adults in Ontario or British Columbia were recruited to participate in a cross-sectional survey (n = 1988). Self-reported measures included demographic factors, work-related variables, perceived level of activity limitation at work, and presence of work safety vulnerability factors utilizing a novel framework. Reporting a disability at work was significantly associated with greater hazard exposure than those without a disability. In addition, those reporting a disability at work were more likely to be employed in conditions where hazard exposure was combined with inadequate policies and procedures, or hazard exposures were combined with inadequate empowerment. Work safety vulnerability is one way that health inequalities can be perpetuated even among those with disabilities who have found work. Our results suggest that employers and policy makers need to focus on assessing and addressing hazard exposures and targeting occupational health and safety resources in the workplace in a way that includes workers with disabilities. Implications for Rehabilitation Workers with disabilities experience greater hazard exposure than those without a disability. Those with moderate and severe disabilities reported occupational health and safety vulnerability, suggesting that workplace accommodations should be available to a broader range of disability levels. It appears that, above and beyond standard safety procedures, providing workplace accommodations for people with disabilities may further reduce their hazard exposure and improve their safety.

  7. 75 FR 62147 - Federal Advisory Council on Occupational Safety and Health (FACOSH)

    Science.gov (United States)

    2010-10-07

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2010-0031] Federal Advisory Council on Occupational Safety and Health (FACOSH) AGENCY: Occupational Safety and Health... Advisory Council on Occupational Safety and Health (FACOSH) will meet October 21, 2010, in Washington, DC...

  8. 77 FR 22355 - Federal Advisory Council on Occupational Safety and Health (FACOSH)

    Science.gov (United States)

    2012-04-13

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2012-0006] Federal Advisory Council on Occupational Safety and Health (FACOSH) AGENCY: Occupational Safety and Health... Federal Advisory Council on Occupational Safety and Health (FACOSH) will meet May 3, 2012, in Washington...

  9. 29 CFR 1960.80 - Secretary's evaluations of agency occupational safety and health programs.

    Science.gov (United States)

    2010-07-01

    ... EMPLOYEE OCCUPATIONAL SAFETY AND HEALTH PROGRAMS AND RELATED MATTERS Evaluation of Federal Occupational Safety and Health Programs § 1960.80 Secretary's evaluations of agency occupational safety and health... evaluating an agency's occupational safety and health program. To accomplish this, the Secretary shall...

  10. 76 FR 71077 - Federal Advisory Council on Occupational Safety and Health (FACOSH)

    Science.gov (United States)

    2011-11-16

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2011-0192] Federal Advisory Council on Occupational Safety and Health (FACOSH) AGENCY: Occupational Safety and Health... Federal Advisory Council on Occupational Safety and Health (FACOSH) will meet Thursday, December 1, 2011...

  11. 77 FR 58174 - Federal Advisory Council on Occupational Safety and Health (FACOSH)

    Science.gov (United States)

    2012-09-19

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2012-0006] Federal Advisory Council on Occupational Safety and Health (FACOSH) AGENCY: Occupational Safety and Health... Occupational Safety and Health (FACOSH) will meet October 18, 2012, in Washington, DC. DATES: FACOSH meeting...

  12. 76 FR 28816 - Federal Advisory Council on Occupational Safety and Health (FACOSH)

    Science.gov (United States)

    2011-05-18

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2011-0061] Federal Advisory Council on Occupational Safety and Health (FACOSH) AGENCY: Occupational Safety and Health... Advisory Council on Occupational Safety and Health (FACOSH) will meet June 7, 2011, in Washington, DC. On...

  13. 75 FR 52988 - National Advisory Committee on Occupational Safety and Health

    Science.gov (United States)

    2010-08-30

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2010-0012] National Advisory Committee on Occupational Safety and Health AGENCY: Occupational Safety and Health... Occupational Safety and Health (NACOSH) will meet September 14 and 15, 2010, in Washington, DC. In conjunction...

  14. 78 FR 68865 - Federal Advisory Council on Occupational Safety and Health (FACOSH)

    Science.gov (United States)

    2013-11-15

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2013-0013] Federal Advisory Council on Occupational Safety and Health (FACOSH) AGENCY: Occupational Safety and Health... Occupational Safety and Health (FACOSH) will meet December 5, 2013, in Washington, DC. DATES: FACOSH meeting...

  15. 78 FR 30337 - Federal Advisory Council on Occupational Safety and Health (FACOSH)

    Science.gov (United States)

    2013-05-22

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2013-0013] Federal Advisory Council on Occupational Safety and Health (FACOSH) AGENCY: Occupational Safety and Health... Federal Advisory Council on Occupational Safety and Health (FACOSH) will meet on June 6, 2013, in...

  16. 76 FR 60535 - Federal Advisory Council on Occupational Safety and Health

    Science.gov (United States)

    2011-09-29

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA--2011-0116] Federal Advisory Council on Occupational Safety and Health AGENCY: Occupational Safety and Health... the Federal Advisory Council on Occupational Safety and Health (FACOSH) until October 31, 2011. DATES...

  17. Safer electronic health records safety assurance factors for EHR resilience

    CERN Document Server

    Sittig, Dean F

    2015-01-01

    This important volume provide a one-stop resource on the SAFER Guides along with the guides themselves and information on their use, development, and evaluation. The Safety Assurance Factors for EHR Resilience (SAFER) guides, developed by the editors of this book, identify recommended practices to optimize the safety and safe use of electronic health records (EHRs). These guides are designed to help organizations self-assess the safety and effectiveness of their EHR implementations, identify specific areas of vulnerability, and change their cultures and practices to mitigate risks.This book pr

  18. Flight safety measurements of UAVs in congested airspace

    Directory of Open Access Journals (Sweden)

    Xiang Jinwu

    2016-10-01

    Full Text Available Describing spatial safety status is crucial for high-density air traffic involving multiple unmanned aerial vehicles (UAVs in a complex environment. A probabilistic approach is proposed to measure safety situation in congested airspace. The occupancy distribution of the airspace is represented with conflict probability between spatial positions and UAV. The concept of a safety envelope related to flight performance and response time is presented first instead of the conventional fixed-size protected zones around aircraft. Consequently, the conflict probability is performance-dependent, and effects of various UAVs on safety can be distinguished. The uncertainty of a UAV future position is explicitly accounted for as Brownian motion. An analytic approximate algorithm for the conflict probability is developed to decrease the computational consumption. The relationship between safety and flight performance are discussed for different response times and prediction intervals. To illustrate the applications of the approach, an experiment of three UAVs in formation flight is performed. In addition, an example of trajectory planning is simulated for one UAV flying over airspace where five UAVs exist. The validation of the approach shows its potential in guaranteeing flight safety in highly dynamic environment.

  19. Six Tips for College Health and Safety

    Science.gov (United States)

    ... ways to manage stress are to get enough sleep (7 to 8 hours a day) , avoid drugs and alcohol, connect socially, and take time for yourself. Seek help from a medical or mental health professional if you are depressed or experiencing distress. If ...

  20. Water Safety

    Science.gov (United States)

    ... Staying Safe Videos for Educators Search English Español Water Safety KidsHealth / For Parents / Water Safety What's in ... remains your best measure of protection. Making Kids Water Wise It's important to teach your kids proper ...

  1. Integrated occupational safety and health management solutions and industrial cases

    CERN Document Server

    Häkkinen, Kari; Niskanen, Toivo

    2015-01-01

    Maximizing reader insights into a new movement toward leadership approaches that are collaborated and shared,  and which views Occupational Safety and Health (OSH) and performance excellence within the wider examination of leadership relationships and practices, this book argues that these relationships and processes are so central to the establishment of OSH functioning that studying them warrants a broad, cross-disciplinary, multiple method analysis. Exploring the complexity of leadership by the impact that contexts (e.g., national and organizational culture) may have on leaders, this book discusses the related literature, then moves forward to show how a more comprehensive practical approach to Occupational Safety and Health and performance excellence can function on levels pertaining to events, individuals, groups, and organizations. This book proposes that greater clarity in understanding leadership in Occupational Safety and Health and performance excellence can be developed from addressing two fundame...

  2. An Evaluation Tool for Agricultural Health and Safety Mobile Applications.

    Science.gov (United States)

    Reyes, Iris; Ellis, Tammy; Yoder, Aaron; Keifer, Matthew C

    2016-01-01

    As the use of mobile devices and their software applications, or apps, becomes ubiquitous, use amongst agricultural working populations is expanding as well. The smart device paired with a well-designed app has potential for improving workplace health and safety in the hands of those who can act upon the information provided. Many apps designed to assess workplace hazards and implementation of worker protections already exist. However, the abundance and diversity of such applications also presents challenges regarding evaluation practices and assignation of value. This is particularly true in the agricultural workspace, as there is currently little information on the value of these apps for agricultural safety and health. This project proposes a framework for developing and evaluating apps that have potential usefulness in agricultural health and safety. The evaluation framework is easily transferable, with little modification for evaluation of apps in several agriculture-specific areas.

  3. Regulatory system reform of occupational health and safety in China

    Science.gov (United States)

    WU, Fenghong; CHI, Yan

    2015-01-01

    With the explosive economic growth and social development, China’s regulatory system of occupational health and safety now faces more and more challenges. This article reviews the history of regulatory system of occupational health and safety in China, as well as the current reform of this regulatory system in the country. Comprehensive, a range of laws, regulations and standards that promulgated by Chinese government, duties and responsibilities of the regulatory departments are described. Problems of current regulatory system, the ongoing adjustments and changes for modifying and improving regulatory system are discussed. The aim of reform and the incentives to drive forward more health and safety conditions in workplaces are also outlined. PMID:25843565

  4. Promoting Occupational Safety and Health for Cambodian Entertainment Sector Workers.

    Science.gov (United States)

    Hsu, Lee-Nah; Howard, Richard; Torriente, Anna Maria; Por, Chuong

    2016-08-01

    Cambodia has developed booming textile, garment, tourism, and entertainment service industries since the mid-1990s. The 2007 global financial crisis pushed many garment workers, who lost their jobs, into the entertainment sector. Entertainment workers are typically engaged informally by their employers and are subjected to long working hours, sexual harassment, and violence. Many who sell beverages are forced into excessive alcohol consumption as part of their work. Many are also expected by their employers and clients to provide sexual services. To address unsafe and unhealthy working conditions for these workers, an innovative occupational safety and health regulation was adopted in 2014. This first-of-its-kind occupational safety and health regulation was developed jointly by the Cambodian Ministry of Labour and Vocational Training and employers' and workers' organizations in the entertainment sector. The implementation of this regulation can also be a viable contribution of occupational safety and health to HIV interventions for these workers. © The Author(s) 2016.

  5. Leveraging best practices to promote health, safety, sustainability, and stewardship.

    Science.gov (United States)

    Weiss, Marjorie D

    2013-08-01

    Strategically leveraging health and safety initiatives with sustainability and stewardship helps organizations improve profitability and positively impact team member and customer attachment to the organization. Collective efficacy enhances the triple bottom line: healthy people, healthy planet, and healthy profits. The HS(3)™ Best Practice Exchanges group demonstrated that collective efficacy can leverage the social cohesion, communication channels, and activities within workplaces to promote a healthy, sustainable work culture. This in turn (1) protects the health and safety of workers, (2) preserves the natural environment, and (3) increases attachment to the organization. Community-based participatory research using the Attach21 survey assessed the progress of these companies in their efforts to integrate health, safety, sustainability, and stewardship. Monthly Best Practice Exchanges promoted collective efficacy by providing support, encouragement, and motivation to share and adopt new ideas. Copyright 2013, SLACK Incorporated.

  6. A review of international sources for road safety measures assessment.

    NARCIS (Netherlands)

    Yannis, G. Weijermars, W. & Kauppila, J.

    2012-01-01

    The efficiency assessment of road safety measures is considered to be an extremely useful tool in decision making; in particular, cost-benefit and cost-effectiveness analyses are carried out in several countries, in a more or less systematic way. The objective of this paper is to present findings

  7. Awareness and utilization of abattoir safety measures in Katsina ...

    African Journals Online (AJOL)

    The study assessed utilization of abattoir safety measures in Katsina South and Central senatorial districts, Nigeria. Information was obtained from a total of 80 abattoir workers in each district, while frequency counts, percentages and independent sample t-test were used to analyze data. The majority, in the respective ...

  8. 49 CFR Appendix B to Part 222 - Alternative Safety Measures

    Science.gov (United States)

    2010-10-01

    .... 222, App. B Appendix B to Part 222—Alternative Safety Measures Introduction A public authority seeking... requirements associated with an SSM as listed in appendix A is revised or deleted, data or analysis supporting...); d. Photographic or video equipment deployed to capture images sufficient to document the violation...

  9. A tool for assessment of animal health laboratory safety and biosecurity: The safety module of the Food and Agriculture Organization’s laboratory mapping tool

    OpenAIRE

    Mouillé, B; Dauphin, G; Wiersma, L; Blacksell, SD; Claes, F; Kalpravidh, W; Kabore, Y; Hietala, S

    2018-01-01

    The Laboratory Management Tool (LMT) is a standardized spreadsheet-based assessment tool developed to help support national, regional, and global efforts to maintain an effective network of animal health and veterinary public health laboratories. The safety and biosecurity module of the LMT (LMT-S) includes 98 measures covering administrative, operational, engineering, and personal protective equipment practices used to provide laboratory safety and biosecurity. Performance aspects of laborat...

  10. Occupational safety and health in the United kingdom: securing future workplace health and wellbeing.

    Science.gov (United States)

    Harrison, John

    2012-01-01

    The industrial revolution that took place in the United Kingdom (UK) between 1760 and 1830 lead to profound social change, with rapid urbanisation associated with squalid living conditions and epidemics of infectious diseases. The next 150 yr or so saw the introduction of many specific acts of health and safety legislation. In 1974 new overarching primary legislation was introduced that would produce a step change in the evolution of health and safety enforcement. In 2004, a new strategy was launched designed to promote a vision embedding health and safety as a cornerstone of a civilised society and to achieve a record of workplace health and safety that leads the world. Good progress in controlling many safety hazards and improving occupational hygiene has been made. There has been a fall in numbers of a wide range of injuries and diseases or illnesses since 2000. The challenge will be to maintain these favourable trends and prepare for new and emerging diseases at a time when resources are diminishing. The importance of occupational health within the UK health and safety strategy has been recognised over the last decade. Occupational health is developing a new paradigm which combines classical health risk management with assessment of workability, rehabilitation back to work and promotion of health and wellbeing. There is an increasing recognition that being in supported employment is good for health and reduces health inequalities.

  11. Occupational health and safety in underground mines

    International Nuclear Information System (INIS)

    Martinson, M.J.

    1976-01-01

    An historical review of the health hazards associated with the inhalation of airborne radionuclides in uraniummines is given. A set of regulations regarding radiation standards for uranium mining was approved by the American President in 1967. Since then the hazard of uranium mining has been subjected to searching public enquiry at Congressional Hearings and been the subject of an unprecedented spate of regulatory standards. Design criteria for mine ventilation are described

  12. Annual health, safety and environmental performance report for 1993

    Energy Technology Data Exchange (ETDEWEB)

    Gallapher, J D; Wright, M G

    1994-05-01

    This report summarizes the occupational health and safety and the environmental protection record of the operations of Atomic Energy of Canada Limited (AECL) during 1993. An introduction highlights the results and describes the facilities and organizational systems. Subsequent sections indicate the performance of the company with respect to personnel radiation exposures, occupational injuries, the handling of wastes, and the release of materials into the environment. Programs in health, safety and environmental protection are presented, along with site remediation and emergency preparedness practices. (author). 14 figs.

  13. Annual health, safety and environmental performance report for 1993

    International Nuclear Information System (INIS)

    Gallapher, J.D.; Wright, M.G.

    1994-05-01

    This report summarizes the occupational health and safety and the environmental protection record of the operations of Atomic Energy of Canada Limited (AECL) during 1993. An introduction highlights the results and describes the facilities and organizational systems. Subsequent sections indicate the performance of the company with respect to personnel radiation exposures, occupational injuries, the handling of wastes, and the release of materials into the environment. Programs in health, safety and environmental protection are presented, along with site remediation and emergency preparedness practices. (author). 14 figs

  14. Biomonitoring at the UK Health and Safety Laboratory.

    Science.gov (United States)

    Cocker, J; Jones, K; Morton, J; Mason, H J

    2007-05-01

    The UK Health and Safety Laboratory (HSL) provides research and analytical support to the Health and Safety Executive, other Government Departments and employers. In the area of biomonitoring HSL conducts research studies and provides an analytical service for regular surveillance of worker exposure to hazardous substances. This paper gives brief examples of how data from such studies can be used to develop biological monitoring guidance values for isocyanates, polycyclic aromatic hydrocarbons and hexavalent chromium. In addition, a study of occupational exposure to copper chrome arsenic wood preservatives is briefly described to show how biological monitoring can be used for post-approval surveillance of a biocide.

  15. Occupational safety and health education and training for underserved populations.

    Science.gov (United States)

    O'Connor, Tom; Flynn, Michael; Weinstock, Deborah; Zanoni, Joseph

    2014-01-01

    This article presents an analysis of the essential elements of effective occupational safety and health education and training programs targeting underserved communities. While not an exhaustive review of the literature on occupational safety and health training, the paper provides a guide for practitioners and researchers to the key factors they should consider in the design and implementation of training programs for underserved communities. It also addresses issues of evaluation of such programs, with specific emphasis on considerations for programs involving low-literacy and limited-English-speaking workers.

  16. Occupational safety and health training in Alaska.

    Science.gov (United States)

    Hild, C M

    1992-01-01

    We have eleven years of experience delivering a wide variety of worker education programs in cross-cultural settings to reduce the levels of occupational fatalities and injuries in Alaska. We published an instructional manual and informational poster for workers, on Alaska's "Right-To-Know" law regarding chemical and physical hazards. The "Job Hazard Recognition Program" curriculum for high school students has received national acclaim for being proactive in dealing with worker safety education before the student becomes a member of the work force. Adult educational programs and materials have been designed to include less lecture and formal presentation, and more practical "hands on" and on-the-job experience for specific trades and hazards. New industry specific manuals deal with hazardous waste reduction as a method to reduce harm to the employee. Difficulty in getting instructors and training equipment to rural locations is dealt with by becoming creative in scheduling classes, using locally available equipment, and finding regional contacts who support the overall program. Alternative approaches to funding sources include building on regional long-term plans and establishing complementary program objectives.

  17. Measurement and analysis of CEFR safety and shim rod worth

    International Nuclear Information System (INIS)

    Chen Yiyu; Yang Yong; Gang Zhi; Xu Li; Yang Xiaoyan; Zhou Keyuan; Hu Dingsheng

    2013-01-01

    The reactivity worth of safety rods and shim rods in critical phase and operating phase was calculated respectively using Monte Carlo program in this paper. In addition, the reactivity worth of safety rods and shim rods was measured by the rod drop-off method and period method. The experimental results are in good agreement with the calculated values with less than 5% error. It illustrates the high calculation precision of Monte Carlo program, which provides a practical reference for subsequent application of Monte Carlo program in future demonstration fast reactors. (authors)

  18. Occupational Safety & Health. Inspectors' Opinions on Improving OSHA Effectiveness. Fact Sheet for Subcommittee on Health and Safety, Committee on Education and Labor, House of Representatives.

    Science.gov (United States)

    General Accounting Office, Washington, DC. Div. of Human Resources.

    Questionnaires gathered opinions of all Occupational Safety and Health Administration (OSHA) field supervisors and a randomly selected sample of one-third of the compliance officers about OSHA's approach to improving workplace safety and health. Major topics addressed were enforcement, safety and health standards, education and training, employer…

  19. Mochovce NPP safety measures evaluation from point of view of operational safety enhancement

    International Nuclear Information System (INIS)

    Cillik, I.; Vrtik, L.

    2000-01-01

    Mochovce NPP consists of four reactor units of WWER 440/V213 type and it is located in the south-middle part of Slovakia. At present first unit operated and the second one under the construction finishing. As these units represent second generation of WWER reactor design, the additional safety measures (SM) were implemented to enhance operational and nuclear safety according to the recommendations of performed international audits and operational experience based on exploitation of other similar units (as Dukovany and J. Bohunice NPPs). These requirements result into a number of SMs grouped according to their purpose to reach recent international requirements on nuclear and operational safety. The paper presents the bases used for safety measures establishing including their grouping into the comprehensive tasks covering different areas of safety goals as well as structural organization of a project management of including participating companies and work performance. More, results are given regarding contribution of selected SMs to the total core damage frequency decreasing. (author)

  20. PSA analysis focused on Mochovce NPP safety measures evaluation from operational safety point of view

    International Nuclear Information System (INIS)

    Cillik, I.; Vrtik, L.

    2001-01-01

    Mochovce NPP consists of four reactor units of WWER 440/V213 type and it is located in the south-middle part of Slovakia. At present first unit operated and the second one under the construction finishing. As these units represent second generation of WWER reactor design, the additional safety measures (SM) were implemented to enhance operational and nuclear safety according to the recommendations of performed international audits and operational experience based on exploitation of other similar units (as Dukovany and J. Bohunice NPPs). These requirements result into a number of SMs grouped according to their purpose to reach recent international requirements on nuclear and operational safety. The paper presents the bases used for safety measures establishing including their grouping into the comprehensive tasks covering different areas of safety goals as well as structural organization of a project management of including participating companies and work performance. More, results are given regarding contribution of selected SMs to the total core damage frequency decreasing.(author)

  1. Evaluating Performance of Safety Management and Occupational Health Using Total Quality Safety Management Model (TQSM

    Directory of Open Access Journals (Sweden)

    E Mohammadfam

    2015-11-01

    Full Text Available Introduction: All organizations, whether public or private, necessitate performance evaluation systems in regard with growth, stability, and development in the competitive fields. One of the existing models for performance evaluation of occupational health and safety management is Total Quality Safety Management model (TQSM. Therefore, the present study aimed to evaluate performance of safety management and occupational health utilizing TQSM model. Methods: In this descriptive-analytic study, the population consisted of 16 individuals, including managers, supervisors, and members of technical protection and work health committee. Then the participants were asked to respond to TQSM questionnaire before and after the implementation of Occupational Health & Safety Advisory Services 18001 (OHSAS18001. Ultimately, the level of each program as well as the TQSM status were determined before and after the implementation of OHSAS18001. Results: The study results showed that the scores obtained by the company before OHSAS 18001’s implementation, was 43.7 out of 312. After implementing OHSAS 18001 in the company and receiving the related certificate, the total score of safety program that company could obtain was 127.12 out of 312 demonstrating a rise of 83.42 scores (26.8%. The paired t-test revealed that mean difference of TQSM scores before and after OHSAS 18001 implementation was proved to be significant (p> 0.05. Conclusion: The study findings demonstrated that TQSM can be regarded as an appropriate model in order to monitor the performance of safety management system and occupational health, since it possesses the ability to quantitatively evaluate the system performance.

  2. An innovative approach to interdisciplinary occupational safety and health education.

    Science.gov (United States)

    Rosen, Mitchel A; Caravanos, Jack; Milek, Debra; Udasin, Iris

    2011-07-01

    The New York and New Jersey Education and Research Center (ERC) provides a range of graduate continuing education for occupational safety and health (OSH) professionals in training. A key element of the education is to provide interdisciplinary training to industrial hygienists, ergonomists, occupational medicine physicians and other health and safety trainees to prepare them for the collaboration required to solve the complex occupational health and safety problems they will face in their careers. This center has developed an innovative interdisciplinary training approach that provides an historical aspect, while allowing the graduate students to identify solutions to occupational issues from a multi-disciplinary approach. The ERC developed a tour that brings students to sites of historical and/or contemporary significance in the occupational safety and health and environmental fields. The ERC has conducted five tours, and has included 85 students and residents as participants. 80% of participants rated the tour as providing a high amount of OSH knowledge gained. 98% of the participants felt the goal of providing interdisciplinary education was achieved. This tour has been successful in bridging the OSH fields to better understand how occupational and environmental exposures have occurred, in order to prevent future exposures so that workplace conditions and health can be improved. Copyright © 2011 Wiley-Liss, Inc.

  3. Health and Safety Considerations of Fermented Sausages

    Directory of Open Access Journals (Sweden)

    Askild Holck

    2017-01-01

    Full Text Available Fermented sausages are highly treasured traditional foods. A large number of distinct sausages with different properties are produced using widely different recipes and manufacturing processes. Over the last years, eating fermented sausages has been associated with potential health hazards due to their high contents of saturated fats, high NaCl content, presence of nitrite and its degradation products such as nitrosamines, and use of smoking which can lead to formation of toxic compounds such as polycyclic aromatic hydrocarbons. Here we review the recent literature regarding possible health effects of the ingredients used in fermented sausages. We also go through attempts to improve the sausages by lowering the content of saturated fats by replacing them with unsaturated fats, reducing the NaCl concentration by partly replacing it with KCl, and the use of selected starter cultures with desirable properties. In addition, we review the food pathogenic microorganisms relevant for fermented sausages (Escherichia coli, Salmonella enterica, Staphylococcus aureus, Listeria monocytogenes, Clostridium botulinum, and Toxoplasma gondii and processing and postprocessing strategies to inhibit their growth and reduce their presence in the products.

  4. Occupational health and safety in Australia.

    Science.gov (United States)

    Macdonald, Wendy; Driscoll, Tim; Stuckey, Rwth; Oakman, Jodi

    2012-01-01

    The focus of OHS in Australia is on workplace-based prevention rather than individual health care. Over the past decade, workers' compensation data have shown continuous improvement in work-related deaths, serious injuries and diseases. Injuries from work-related vehicle incidents are the leading cause of fatalities. There is a high incidence of on-road incidents in light vehicles; this problem is under-recognised, and better incidence data are required to support more effective interventions. Rates of many long-latency diseases such as cancers are underestimated, and again more reliable information is needed, particularly on work-related exposures to carcinogens. Disease-related deaths are largely confined to older workers. Musculoskeletal injuries and disorders are the most frequent and costly OHS problem, constituting a large majority of non-fatal injuries and diseases. There is growing recognition that their risk management should be more evidence based, integrating assessment and control of psychosocial and 'manual handling' hazards. A high rate of population ageing is increasing risk of chronic diseases, including musculoskeletal disorders, which is helping to raise awareness of the importance of protecting and promoting workforce health. Strategies to achieve this have been developed but implementation is at an early stage.

  5. Developing safety performance functions incorporating reliability-based risk measures.

    Science.gov (United States)

    Ibrahim, Shewkar El-Bassiouni; Sayed, Tarek

    2011-11-01

    Current geometric design guides provide deterministic standards where the safety margin of the design output is generally unknown and there is little knowledge of the safety implications of deviating from these standards. Several studies have advocated probabilistic geometric design where reliability analysis can be used to account for the uncertainty in the design parameters and to provide a risk measure of the implication of deviation from design standards. However, there is currently no link between measures of design reliability and the quantification of safety using collision frequency. The analysis presented in this paper attempts to bridge this gap by incorporating a reliability-based quantitative risk measure such as the probability of non-compliance (P(nc)) in safety performance functions (SPFs). Establishing this link will allow admitting reliability-based design into traditional benefit-cost analysis and should lead to a wider application of the reliability technique in road design. The present application is concerned with the design of horizontal curves, where the limit state function is defined in terms of the available (supply) and stopping (demand) sight distances. A comprehensive collision and geometric design database of two-lane rural highways is used to investigate the effect of the probability of non-compliance on safety. The reliability analysis was carried out using the First Order Reliability Method (FORM). Two Negative Binomial (NB) SPFs were developed to compare models with and without the reliability-based risk measures. It was found that models incorporating the P(nc) provided a better fit to the data set than the traditional (without risk) NB SPFs for total, injury and fatality (I+F) and property damage only (PDO) collisions. Copyright © 2011 Elsevier Ltd. All rights reserved.

  6. John M. Eisenberg Patient Safety Awards. System innovation: Veterans Health Administration National Center for Patient Safety.

    Science.gov (United States)

    Heget, Jeffrey R; Bagian, James P; Lee, Caryl Z; Gosbee, John W

    2002-12-01

    In 1998 the Veterans Health Administration (VHA) created the National Center for Patient Safety (NCPS) to lead the effort to reduce adverse events and close calls systemwide. NCPS's aim is to foster a culture of safety in the Department of Veterans Affairs (VA) by developing and providing patient safety programs and delivering standardized tools, methods, and initiatives to the 163 VA facilities. To create a system-oriented approach to patient safety, NCPS looked for models in fields such as aviation, nuclear power, human factors, and safety engineering. Core concepts included a non-punitive approach to patient safety activities that emphasizes systems-based learning, the active seeking out of close calls, which are viewed as opportunities for learning and investigation, and the use of interdisciplinary teams to investigate close calls and adverse events through a root cause analysis (RCA) process. Participation by VA facilities and networks was voluntary. NCPS has always aimed to develop a program that would be applicable both within the VA and beyond. NCPS's full patient safety program was tested and implemented throughout the VA system from November 1999 to August 2000. Program components included an RCA system for use by caregivers at the front line, a system for the aggregate review of RCA results, information systems software, alerts and advisories, and cognitive acids. Following program implementation, NCPS saw a 900-fold increase in reporting of close calls of high-priority events, reflecting the level of commitment to the program by VHA leaders and staff.

  7. Functional safety measurement in the automotive domain : adaptation of PSM

    NARCIS (Netherlands)

    Luo, Y.; Stelma, J.; Brand, van den M.G.J.

    2015-01-01

    In the safety domain, safety standards are used as a development guideline to keep the risk at an acceptable level. Safety of the safety-critical systems can be assessed according to those safety standards. This assessment process is called safety assurance. Due to the manual work, the safety

  8. Multimedia for occupational safety and health training: a pilot study examining a multimedia learning theory.

    Science.gov (United States)

    Wallen, Erik S; Mulloy, Karen B

    2006-10-01

    Occupational diseases are a significant problem affecting public health. Safety training is an important method of preventing occupational illness. Training is increasingly being delivered by computer although theories of learning from computer-based multimedia have been tested almost entirely on college students. This study was designed to determine whether these theories might also be applied to safety training applications for working adults. Participants viewed either computer-based multimedia respirator use training with concurrent narration, narration prior to the animation, or unrelated safety training. Participants then took a five-item transfer test which measured their ability to use their knowledge in new and creative ways. Participants who viewed the computer-based multimedia trainings both did significantly better than the control group on the transfer test. The results of this pilot study suggest that design guidelines developed for younger learners may be effective for training workers in occupational safety and health although more investigation is needed.

  9. [Endorsement of risk management and patient safety by certification of conformity in health care quality assessment].

    Science.gov (United States)

    Waßmuth, Ralf

    2015-01-01

    Certification of conformity in health care should provide assurance of compliance with quality standards. This also includes risk management and patient safety. Based on a comprehensive definition of quality, beneficial effects on the management of risks and the enhancement of patient safety can be expected from certification of conformity. While these effects have strong face validity, they are currently not sufficiently supported by evidence from health care research. Whether this relates to a lack of evidence or a lack of investigation remains open. Advancing safety culture and "climate", as well as learning from adverse events rely in part on quality management and are at least in part reflected in the certification of healthcare quality. However, again, evidence of the effectiveness of such measures is limited. Moreover, additional factors related to personality, attitude and proactive action of healthcare professionals are crucial factors in advancing risk management and patient safety which are currently not adequately reflected in certification of conformity programs.

  10. Working time, health and safety a research synthesis paper

    OpenAIRE

    Tucker, Philip; Folkard, Simon

    2012-01-01

    Outlines contemporary trends, developments and effects with regard to different aspects of working time, such as hours of work and work schedules. Examines the impact of modern working time arrangements on workers' health, well-being and workplace safety. Argues that while long daily hours tend to be associated with acute effects of fatigue, long weekly hours tend to be associated both with acute effects of fatigue as well as chronic fatigue, generating long-term negative health effects. Look...

  11. Positioning radiation safety in occupational safety and health programme in an organization

    International Nuclear Information System (INIS)

    Abed Bin Onn

    2000-01-01

    The Atomic Energy Licensing Act 1984, which is under purview of the Ministry of Science, Technology and Environment, and Occupational Safety and Health Act, OSHA 1994, under Ministry of Human Resources were discussed. RPO responsibilities were discussed in detailed. As the conclusion, organization which complies with the provisions of the AELA 1984 are well on the way to complying the requirements of OSHA 1994

  12. Working Safety in Confined Spaces. Module SH-32. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on working safely in confined spaces in one of 50 modules concerned with job safety and health. This module explains how to recognize potential hazards in confined spaces, how to deal with these hazards, and how planning can prevent accidents. Following the introduction, 17 objectives (each keyed to a page in the text) the…

  13. Risk factors for fishermen's health and safety in Greece

    DEFF Research Database (Denmark)

    Frantzeskou, Elpida; Kastania, Anastasia N; Riza, Elena

    2012-01-01

    Background: This is, to the best of our knowledge, the first occupational health study in Greek fishing. Aim: The aim of the study is to determine the risks for health and safety in Greek fisheries workers by exploring their health status and the health risk factors present in their occupational...... injury, of which half caused more than one day absence, while 14% had a near drowning experience. The health risks factors studied include excessive weight, cardiovascular incidents and dermatological, musculoskeletal, respiratory, hearing, stress, and anxiety problems. The occupational health risk...... factors include alcohol, fatty food consumption, smoking, and lack of physical exercise. Conclusions: The health effects observed are causally related to diet, smoking, and exercise, which in turn relate to the specific working conditions and culture in small-scale fishing that need to be taken...

  14. Materials Handling. Module SH-01. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on materials handling is one of 50 modules concerned with job safety and health. It presents the procedures for safe materials handling. Discussed are manual handling methods (lifting and carrying by hand) and mechanical lifting (lifting by powered trucks, cranes or conveyors). Following the introduction, 15 objectives (each…

  15. Nutrition, Health and Safety in Early Childhood Development ...

    African Journals Online (AJOL)

    This article investigates the nutrition, health and safety status in Early Childhood Development (ECD) programmes and its impact thereof on the quality of care and education in Harare primary schools as perceived by the school heads, ECD teachers and parents. The study is part of a larger study on assessing the quality of ...

  16. Index to Health and Safety Education (Multimedia). First Edition.

    Science.gov (United States)

    University of Southern California, Los Angeles. National Information Center for Educational Media.

    More than 16,000 films, videotapes, recordings and multimedia presentations for teaching health and safety education, driver training, medicine and dentistry, home economics, nursing and physical education are listed in this 620-page catalog. Catalog entries are classified alphabetically by title. Each entry provides a summary of the materials,…

  17. European and International Standards on health and safety in welding

    International Nuclear Information System (INIS)

    Howe, A

    2009-01-01

    A number of European and International Standards on health and safety in welding have been published in recent years and work on several more is nearing completion. These standards have been prepared jointly by the International Standards Organization (ISO) and the European Committee for Standardization (CEN). The standards development work has mostly been led by CEN/TC 121/SC 9, with excellent technical input from experts within Europe; but work on the revision of published standards, which has recently gathered pace, is now being carried out by ISO/TC 44/SC 9, with greater international involvement. This paper gives an overview of the various standards that have been published, are being revised or are under development in this field of health and safety in welding, seeking to (i) increase international awareness of published standards, (ii) encourage wider participation in health and safety in welding standards work and (iii) obtain feedback and solicit comments on standards that are currently under development or revision. Such an initiative is particularly timely because work is currently in progress on the revision of one of the more important standards in this field, namely EN ISO 10882:2001 Health and safety in welding and allied processes- Sampling of airborne particles and gases in the operator's breathing zone - Part 1: Sampling of airborne particles.

  18. 48 CFR 1852.223-70 - Safety and health.

    Science.gov (United States)

    2010-10-01

    ... Contractor shall comply with all Federal, State, and local laws applicable to safety and occupational health... include in any report an expression of opinion as to the fault or negligence of any employee. In addition... (OSHA) or Department of Transportation (DOT) regulations (if applicable). (4) When the Contractor (or...

  19. Management of health, safety and environment in process industry

    DEFF Research Database (Denmark)

    Duijm, Nijs Jan; Fiévez, C.; Gerbec, M.

    2008-01-01

    The present status of industrial HSE management in a number of EU member states is reviewed, with a focus on the integration of health, safety and environment in single management systems. The review provides insight into the standards and paradigms adopted by industry, and it identifies trends...

  20. 29 CFR 1926.20 - General safety and health provisions.

    Science.gov (United States)

    2010-07-01

    ... for any part of the contract work shall require any laborer or mechanic employed in the performance of the contract to work in surroundings or under working conditions which are unsanitary, hazardous, or dangerous to his health or safety. (b) Accident prevention responsibilities. (1) It shall be the...

  1. Corporate social responsibility and safety and health at work

    NARCIS (Netherlands)

    Zwetsloot, G.I.J.M.

    2004-01-01

    This paper about European situation and perspectives on corporate social responsibility and safety and health at work was presented at Jornada Tecnica: Conditiones de Trabajo y Responsabilidad Social. This congress was organised by the Instituto Nacional de Seguridad e Higiene en el Trabajo (INHST)

  2. Design for sustainable development : environmental management and safety and health

    NARCIS (Netherlands)

    Zwetsloot, G.; Bos, J.

    1998-01-01

    This is a report on the EU's environmental management and audit scheme and its interaction with the management of safety and health. The focus is on the interactions at company and at policy level. To illustrate the relevance of the interactions at company level, the Annex includes five case studies

  3. The impact of a modified World Health Organization surgical safety ...

    African Journals Online (AJOL)

    The impact of a modified World Health Organization surgical safety checklist on maternal ... have shown an alarming increase in deaths during or after caesarean delivery. ... Methods. The study was a stratified cluster-randomised controlled trial ... Training of healthcare personnel took place over 1 month, after which the ...

  4. Occupational health and safety management in micro and small enterprises

    DEFF Research Database (Denmark)

    Hasle, Peter

    2015-01-01

    Occupational health and safety management (OHSM) in micro and small enterprises may look like an odd ex-pression. Most owner-managers do not think of OHSM as something to give priority. They are occupied with management of the core business which in many cases constitute a simple fight for survival...

  5. A knowledge infrastructure for occupational safety and health.

    NARCIS (Netherlands)

    van Dijk, Frank J. H.; Verbeek, J. H.; Hoving, J. L.; Hulshof, C. T.

    2010-01-01

    Occupational Safety and Health (OSH) professionals should use scientific evidence to support their decisions in policy and practice. Although examples from practice show that progress has been made in evidence-based decision making, there is a challenge to improve and extend the facilities that

  6. Integrating Occupational Safety and Health into TAFE Courses: Policy Guidelines.

    Science.gov (United States)

    Hill, Graham L.; Mageean, Pauline

    Intended to help administrators, curriculum developers, and teachers integrate occupational health and safety into Australian vocational courses on bricklaying, metal fabrication, and horticulture, this document suggests specific policies and provides further amplification concerning three general policies for that integration. The three general…

  7. Ethics in occupational health and safety: case studies from Gujarat.

    Science.gov (United States)

    Patel, Jagdish; David, Siddarth

    2016-01-01

    Rapid industrialisation in India is giving employment to millions of people in the formal sector, and many more in the unorganised sector. However, the absence of clear policies, poorly enforced regulations, lack of systematic reporting of occupational diseases, lamentable socioeconomic conditions of the workers and their limited access to healthcare make occupational health and safety (OHS) a critical area.

  8. Workplace Safety and Health Topics: Diseases and Injuries

    Science.gov (United States)

    ... December 28, 2017 Content source: National Institute for Occupational Safety and Health Education and Information Division Email Recommend Tweet YouTube Instagram Listen Watch RSS ABOUT About CDC Jobs Funding LEGAL Policies Privacy FOIA No Fear Act OIG 1600 Clifton Road Atlanta , GA 30329-4027 ...

  9. 76 FR 64110 - Safety and Health Management Programs for Mines

    Science.gov (United States)

    2011-10-17

    ... section of this notice. Comment Dates: MSHA will hold the date for comments open until all meetings are... Identification, including workplace inspections for violations of mandatory health and safety standards. Hazard.... Improved communication. Increased productivity. Increased and improved worker and management involvement in...

  10. Occupational safety and health management and risk governance

    NARCIS (Netherlands)

    Dijkman, A.; Terwoert, J.

    2014-01-01

    The advancement in new technologies, substances and new ways of working make it necessary to look beyond traditional methods of risk management. General drivers to emerging occupational safety and health (OSH) risks are: globalisation; demographic changes; technical innovations; changes in risk

  11. 76 FR 58711 - National Farm Safety and Health Week, 2011

    Science.gov (United States)

    2011-09-21

    ... National Farm Safety and Health Week, 2011 By the President of the United States of America A Proclamation... and processing facilities. Physically demanding and all-encompassing, farm work requires the... worked to create new markets for these products, and to provide assistance to farms, supporting jobs...

  12. Gender issues in safety and health at work : a review

    NARCIS (Netherlands)

    Houtman, I.L.D.; Kauppinen, K.; Kumpulainen, R.; Goudswaard, A.

    2003-01-01

    This report explores the gender differences in occupational safety and health. There is strong segregation of women and men into different jobs and tasks at work. Both men and women face significant risks. In general, men suffer more accidents and injuries at work than women do, whereas women report

  13. Occupational safety and health issues associated with green building

    NARCIS (Netherlands)

    Terwoert, J.; Ustailieva, E.

    2013-01-01

    This e-fact provides information on the work-related risk factors and the occupational safety and health (OSH) issues associated the planning and construction of green buildings, their maintenance, renovation (retrofitting), demolition, on-site waste collection. Some of these OSH risks are new

  14. Occupational Health and Safety in the Nigerian Public Sector ...

    African Journals Online (AJOL)

    The focus of this paper is to explore the issue of occupational health and safety ... this paper seeks to examine major causes of occupational hazards in the public ... not report to the management for fear of negative effect that may result from it.

  15. 48 CFR 1852.223-72 - Safety and Health (Short Form).

    Science.gov (United States)

    2010-10-01

    ... 48 Federal Acquisition Regulations System 6 2010-10-01 2010-10-01 true Safety and Health (Short... and Clauses 1852.223-72 Safety and Health (Short Form). As prescribed in 1823.7001(e), insert the following clause: Safety and Health (Short Form) (APR 2002) (a) Safety is the freedom from those conditions...

  16. 75 FR 28661 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2010-05-21

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2010-0012] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... Committee on Occupational Safety and Health (NACOSH). SUMMARY: The Assistant Secretary of Labor for...

  17. 76 FR 60085 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2011-09-28

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2011-0065] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... Assistant Secretary of Labor for Occupational Safety and Health requests nominations for membership on...

  18. 77 FR 46126 - Maritime Advisory Committee for Occupational Safety and Health (MACOSH)

    Science.gov (United States)

    2012-08-02

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2012-0003] Maritime Advisory Committee for Occupational Safety and Health (MACOSH) AGENCY: Occupational Safety and... Advisory Committee for Occupational Safety and Health. SUMMARY: OSHA invites interested persons to submit...

  19. 76 FR 73689 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2011-11-29

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2011-0065] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... on Occupational Safety and Health (NACOSH) and NACOSH Work Groups. SUMMARY: The National Advisory...

  20. 77 FR 31398 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2012-05-25

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2012-0019] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... on Occupational Safety and Health (NACOSH) and NACOSH Work Groups. SUMMARY: NACOSH will meet June 20...

  1. 77 FR 33495 - Maritime Advisory Committee for Occupational Safety and Health (MACOSH)

    Science.gov (United States)

    2012-06-06

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2012-0003] Maritime Advisory Committee for Occupational Safety and Health (MACOSH) AGENCY: Occupational Safety and..., Docket No. OSHA- 2012-0003, U.S. Department of Labor, Occupational Safety and Health Administration, Room...

  2. 76 FR 18798 - Maritime Advisory Committee for Occupational Safety and Health (MACOSH)

    Science.gov (United States)

    2011-04-05

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No OSHA-2011-0007] Maritime Advisory Committee for Occupational Safety and Health (MACOSH) AGENCY: Occupational Safety and.... MACOSH will contribute to OSHA's performance of the duties imposed by the Occupational Safety and Health...

  3. 77 FR 64549 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2012-10-22

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2012-0019] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... on Occupational Safety and Health (NACOSH) and a NACOSH Work Group. SUMMARY: NACOSH will meet...

  4. 78 FR 30937 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2013-05-23

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2013-0015] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... meeting is open to the public. Section 7(a) of the Occupational Safety and Health Act of 1970 (OSH Act...

  5. 76 FR 54806 - Maritime Advisory Committee for Occupational Safety and Health (MACOSH)

    Science.gov (United States)

    2011-09-02

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2011-0007] Maritime Advisory Committee for Occupational Safety and Health (MACOSH) AGENCY: Occupational Safety and... Committee for Occupational Safety and Health (MACOSH) was established under Section 7 of the Occupational...

  6. 77 FR 62536 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2012-10-15

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2012-0019] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... Section 7(a) of the Occupational Safety and Health Act of 1970 (OSH Act) (29 U.S.C. 651, 656) to advise...

  7. 77 FR 5577 - Maritime Advisory Committee for Occupational Safety and Health (MACOSH)

    Science.gov (United States)

    2012-02-03

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2012-0003] Maritime Advisory Committee for Occupational Safety and Health (MACOSH) AGENCY: Occupational Safety and..., Docket No. OSHA- 2012-0003, U.S. Department of Labor, Occupational Safety and Health Administration, Room...

  8. 77 FR 43616 - National Advisory Committee on Occupational Safety and Health (NACOSH)

    Science.gov (United States)

    2012-07-25

    ... DEPARTMENT OF LABOR Occupational Safety and Health Administration [Docket No. OSHA-2012-0019] National Advisory Committee on Occupational Safety and Health (NACOSH) AGENCY: Occupational Safety and... Assistant Secretary of Labor for Occupational Safety and Health requests nominations for membership on...

  9. Proceedings of The First National Seminar on Safety, Public Health and Environment

    International Nuclear Information System (INIS)

    Hiswara, Eri; Bunawas; Dumais, Johannes P.; Alatas, Zubaidah; Melyani

    2001-11-01

    The first national seminar of safety, public health and environment was held in 23-24 Oct 2001 at the center for research and development of radiation safety and nuclear biomedicine natural energy agency, Indonesia have presented 27 papers, about safety, public health and environment the proceedings is expected to give illustration of the research result on safety, health and environment. (PPIN)

  10. Integrated Approaches to Occupational Health and Safety: A Systematic Review.

    Science.gov (United States)

    Cooklin, A; Joss, N; Husser, E; Oldenburg, B

    2017-09-01

    The study objective was to conduct a systematic review of the effectiveness of integrated workplace interventions that combine health promotion with occupational health and safety. Electronic databases (n = 8), including PsychInfo and MEDLINE, were systematically searched. Studies included were those that reported on workplace interventions that met the consensus definition of an "integrated approach," published in English, in the scientific literature since 1990. Data extracted were occupation, worksite, country, sample size, intervention targets, follow-up period, and results reported. Quality was assessed according to American College of Occupational and Environmental Medicine Practice Guidelines. Heterogeneity precluded formal meta-analyses. Results were classified according to the outcome(s) assessed into five categories (health promotion, injury prevention, occupational health and safety management, psychosocial, and return-on-investment). Narrative synthesis of outcomes was performed. A total of 31 eligible studies were identified; 23 (74%) were (quasi-)experimental trials. Effective interventions were most of those aimed at improving employee physical or mental health. Less consistent results were reported from integrated interventions targeting occupational health and safety management, injury prevention, or organizational cost savings. Integrated approaches have been posed as comprehensive solutions to complex issues. Empirical evidence, while still emerging, provides some support for this. Continuing investment in, and evaluation of, integrated approaches are worthwhile.

  11. Urgent Safety Measures in Japan after Great East Japan Earthquake

    International Nuclear Information System (INIS)

    Taniura, W.; Otani, H.

    2012-01-01

    Due to tsunami triggered by the Great East Japan Earthquake on March 11, 2011, the operating and refueling reactor facilities at Fukushima Dai-ichi and Dai-ni Nuclear Power Plants of Tokyo Electric Power Co. caused a nuclear hazard. Japanese electric power companies voluntarily began to compile various urgent measures against tsunami within the week the hazard was caused. As for the urgent safety measures of each licensee, it is clarified that effective measures have been appropriately implemented as a result of the inspection of the national government, the verification based on the guideline of the Japan Society of Maintenology and the stress test. (author)

  12. Directly acting spring loaded safety valves as shock reducing measure

    International Nuclear Information System (INIS)

    Ismaier, A.; Schluecker, E.

    2010-01-01

    Hydraulic shocks as induced by fast closure of armatures or by sudden pump failures are massive impacts in piping systems and require extensive measures to absorb the generated load. Basically the avoidance of water hammers are preferable but in case of emergency shutdowns unavoidable hydraulic shocks have to be reduced by appropriate measures. The authors describe experiments with spring loaded safety valves as shock reducing measures. It was shown that the vale dimensions is essential for the efficacy. A realistic modeling is possible using the one-dimensional fluid mechanics code ROLAST.

  13. Safe Handling and Use of Flammable and Combustible Materials. Module SH-30. Safety and Health.

    Science.gov (United States)

    Center for Occupational Research and Development, Inc., Waco, TX.

    This student module on safe handling and use of flammable and combustible materials is one of 50 modules concerned with job safety and health. This module introduces the student to the hazards of flammable and combustible materials and the measures necessary to control those hazards. Following the introduction, 14 objectives (each keyed to a page…

  14. Lean Six-Sigma in Aviation Safety: An implementation guide for measuring aviation system’s safety performance

    OpenAIRE

    Panagopoulos, I.; Atkin, C.J.; Sikora, I.

    2016-01-01

    The paper introduces a conceptual framework that could improve the safety performance measurement process and ultimately the aviation system safety performance. The framework provides an implementation guide on how organisations could design and develop a proactive, measurement tool for assessing and measuring the Acceptable Level of Safety Performance (ALoSP) at sigma (σ) level, a statistical measurement unit. In fact, the methodology adapts and combines quality management tools, a leading i...

  15. Emerging trends in PHWR safety - post Fukushima measures

    International Nuclear Information System (INIS)

    Nitheanandan, T.

    2015-01-01

    Nuclear power continues to be the choice for many countries that are seeking to enhance their energy security and reduce their carbon emissions. Nuclear power plants are complex systems which require multiple layers of protection. The fundamental principle of nuclear power safety technology is ‘Defence-in-Depth’ that underlies all safety activities - organizational, behavioural and technical. This provides layers of overlapping barrier protections so that, in the unlikely event that failure occurs, it would be compensated or corrected without causing harm to individuals or the public at large. Defence-in-depth encompasses prevention, control, protection, severe accident management and consequence mitigation, and offsite emergency response measures. Reactor Safety Science and Technology (S and T) has evolved over more than four decades in a number of PHWR countries. The PHWR operators, regulators and national research laboratories have dedicated S and T programs to continuously improve plant safety, operations and margins. The S and T is focused on finding simpler, less costly and more reliable safety system designs. These improvements are continuously incorporated in current units, refurbished units and proposed new builds. The Fukushima accident forced most nuclear nations to reassess and implement reactor design upgrades. The lessons learned from Fukushima have generated some nuclear safety enhancements such as: Design considerations for natural hazards, Diversity of heat sinks, Consideration of extended duration station blackout, Improvements to Severe Accident Management and SAM Operational aids, Accident instrumentation, Offsite management such as the use of predictive exposure tools, and Design considerations for Spent Fuel Pools. The plenary presentation will provide some of the emerging trends following the Fukushima accident. Examples of these emerging trends in Canada and on the international scene, will be presented. (author)

  16. Family climate for road safety: a new concept and measure.

    Science.gov (United States)

    Taubman-Ben-Ari, Orit; Katz-Ben-Ami, Liat

    2013-05-01

    This research adapted the workplace concept of safety climate to the domain of safe driving, defining a new construct of "family climate for road safety". Four studies were conducted in Israel with the aim of developing and validating a multidimensional instrument to assess this construct among young drivers. Study 1 (n=632) focused on developing the Family Climate for Road Safety Scale (FCRSS), a self-report scale assessing the family climate by means of seven aspects of the parent-child relationship: Modeling, Feedback, Communication, Monitoring, Noncommitment, Messages, and Limits. Significant differences were found between young men and women on all factors. In addition, significant associations were found between the FCRSS factors on the one hand, and the reported frequency of risky driving and personal commitment to safety on the other. Studies 2-4 confirmed the factorial structure of the FCRSS and the reliability of its factors, adding to its criterion and convergent validity. Study 2 (n=178) yielded significant associations between the scale and young drivers' perception of their parents as involved, encouraging autonomy, and providing warmth; Study 3 (n=117) revealed significant associations between the scale and youngsters' reported proneness to take risks while driving, as well as significant associations between the factors and various dimensions of family functioning; and Study 4 (n=156) found associations between the FCRSS factors and both driving styles (risky, angry, anxious, careful) and family cohesion and adaptability. The discussion deals with the validity and utility of the concept of family climate for road safety and its measurement, addressing the practical implications for road safety. Copyright © 2013 Elsevier Ltd. All rights reserved.

  17. Health and safety plan for operations performed for the Environmental Restoration Program

    International Nuclear Information System (INIS)

    Trippet, W.A. II; Reneau, M.; Morton, S.L.

    1992-04-01

    This document constitutes the generic health and safety plan for the Environmental Restoration Program (ERP). It addresses the health and safety requirements of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA); Occupational Safety and Health Administration (OSHA) 29 CFR 1910.120 standard; and EG ampersand G Idaho, Inc. This plan is a guide to individuals who must complete a health and safety plan for a task performed for the EPR. It contains a task specific addendum that, when completed, specifically addresses task specific health and safety issues. This health and safety plan reduces the time it takes to write a task specific health and safety plan by providing discussions of requirements, guidance on where specific information is located, and specific topics in the Addendum that must be discussed at a task level. This format encourages a complete task specific health and safety plan and a standard for all health and safety plans written for ERP

  18. Health and safety plan for operations performed for the Environmental Restoration Program

    Energy Technology Data Exchange (ETDEWEB)

    Trippet, W.A. II (IT Corp., (United States)); Reneau, M.; Morton, S.L. (EG and G Idaho, Inc., Idaho Falls, ID (United States))

    1992-04-01

    This document constitutes the generic health and safety plan for the Environmental Restoration Program (ERP). It addresses the health and safety requirements of the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA); Occupational Safety and Health Administration (OSHA) 29 CFR 1910.120 standard; and EG G Idaho, Inc. This plan is a guide to individuals who must complete a health and safety plan for a task performed for the EPR. It contains a task specific addendum that, when completed, specifically addresses task specific health and safety issues. This health and safety plan reduces the time it takes to write a task specific health and safety plan by providing discussions of requirements, guidance on where specific information is located, and specific topics in the Addendum that must be discussed at a task level. This format encourages a complete task specific health and safety plan and a standard for all health and safety plans written for ERP.

  19. Participatory approach to improving safety, health and working conditions in informal economy workplaces in Cambodia.

    Science.gov (United States)

    Kawakami, Tsuyoshi; Tong, Leng; Kannitha, Yi; Sophorn, Tun

    2011-01-01

    The present study aimed to improve safety and health in informal economy workplaces such as home workplaces, small construction sites, and rural farms in Cambodia by using "participatory" approach. The government, workers' and employers' organizations and NGOs jointly assisted informal economy workers in improving safety and health by using participatory training methodologies. The steps taken were: (1) to collect existing good practices in safety and health in Cambodia; (2) to develop new participatory training programmes for home workers and small construction sites referring to ILO's WISE training programme, and (3) to train government officers, workers, employers and NGOs as safety and health trainers. The participatory training programmes developed consisted of action-checklists associated with illustrations, good example photo sheets, and texts explaining practical, low-cost improvement measures. The established safety and health trainers reached many informal economy workers through their human networks, and trained them by using the developed participatory training programmes. More than 3,000 informal economy workers were trained and they implemented improvements by using low-cost methods. Participatory training methodologies and active cooperation between the government, workers, employers and NGOs made it possible to provide practical training for those involved in the informal economy workplaces.

  20. Comparison of safety measures with a multicriteria decision aiding technique

    International Nuclear Information System (INIS)

    Lombard, J.

    1985-01-01

    Attributes such as political, social and psychological factors have to be taken into account for the decision-making process. Multiattribute decision-aiding techniques are used to cope with this multidimensionality of the risk management process. A simple example will be given to illustrate how such method can be helpful for the selection of proper safety measures in a rational way. (orig./HP) [de

  1. Status of occupational health and safety in Iran.

    Science.gov (United States)

    Vigeh, Mohsen; Mazaheri, Maria; Seyedaghamiri, Zahrabigom

    2011-12-01

    In recent decades, Iran has had a steadily growing economy with an annual rate of 6% on average. The country's economy is dominantly influenced by oil and natural gas production and related industries like petrochemicals and fertilizers. There are two million job units and sixteen million employees. The occupational health and safety (OHS) system is mainly regulated by two bodies: the Ministry of Health and Medical Education, responsible for occupational health services and legislations; and the Ministry of Labour and Social Affairs, which undertakes the enactment and enforcement of occupational safety legal issues. Inspectorates in each ministry carry out regular health and safety monitoring according to the OHS legislations. The most common occupational health disorders are musculoskeletal problems, respiratory diseases, noise induced hearing loss, and occupational injuries. Because the OHS is a complex system with overlapping responsibilities among the co-responders, its improvement needs well-organized collaboration among Iranian universities, industries, and governmental agencies, and reliable basic data. The present study takes a glance at the situation and activities of the Iranian OHS system.

  2. Psychological safety and error reporting within Veterans Health Administration hospitals.

    Science.gov (United States)

    Derickson, Ryan; Fishman, Jonathan; Osatuke, Katerine; Teclaw, Robert; Ramsel, Dee

    2015-03-01

    In psychologically safe workplaces, employees feel comfortable taking interpersonal risks, such as pointing out errors. Previous research suggested that psychologically safe climate optimizes organizational outcomes. We evaluated psychological safety levels in Veterans Health Administration (VHA) hospitals and assessed their relationship to employee willingness of reporting medical errors. We conducted an ANOVA on psychological safety scores from a VHA employees census survey (n = 185,879), assessing variability of means across racial and supervisory levels. We examined organizational climate assessment interviews (n = 374) evaluating how many employees asserted willingness to report errors (or not) and their stated reasons. Finally, based on survey data, we identified 2 (psychologically safe versus unsafe) hospitals and compared their number of employees who would be willing/unwilling to report an error. Psychological safety increased with supervisory level (P hospital (71% would report, 13% would not) were less willing to report an error than at the psychologically safe hospital (91% would, 0% would not). A substantial minority would not report an error and were willing to admit so in a private interview setting. Their stated reasons as well as higher psychological safety means for supervisory employees both suggest power as an important determinant. Intentions to report were associated with psychological safety, strongly suggesting this climate aspect as instrumental to improving patient safety and reducing costs.

  3. How to measure health improvement?

    NARCIS (Netherlands)

    Fazelzadeh, Parastoo

    2017-01-01

    Human health is impacted by a complex network of interactions between biological pathways, mechanisms, processes, and organs, which need to be able to adapt to a continuously changing environment to maintain health. This adaptive ability is called ‘phenotypic flexibility’. It is thought that

  4. Development of a multilevel health and safety climate survey tool within a mining setting.

    Science.gov (United States)

    Parker, Anthony W; Tones, Megan J; Ritchie, Gabrielle E

    2017-09-01

    This study aimed to design, implement and evaluate the reliability and validity of a multifactorial and multilevel health and safety climate survey (HSCS) tool with utility in the Australian mining setting. An 84-item questionnaire was developed and pilot tested on a sample of 302 Australian miners across two open cut sites. A 67-item, 10 factor solution was obtained via exploratory factor analysis (EFA) representing prioritization and attitudes to health and safety across multiple domains and organizational levels. Each factor demonstrated a high level of internal reliability, and a series of ANOVAs determined a high level of consistency in responses across the workforce, and generally irrespective of age, experience or job category. Participants tended to hold favorable views of occupational health and safety (OH&S) climate at the management, supervisor, workgroup and individual level. The survey tool demonstrated reliability and validity for use within an open cut Australian mining setting and supports a multilevel, industry specific approach to OH&S climate. Findings suggested a need for mining companies to maintain high OH&S standards to minimize risks to employee health and safety. Future research is required to determine the ability of this measure to predict OH&S outcomes and its utility within other mine settings. As this tool integrates health and safety, it may have benefits for assessment, monitoring and evaluation in the industry, and improving the understanding of how health and safety climate interact at multiple levels to influence OH&S outcomes. Copyright © 2017 National Safety Council and Elsevier Ltd. All rights reserved.

  5. Oak Ridge National Laboratory Health and Safety Long-Range Plan: Fiscal years 1989--1995

    Energy Technology Data Exchange (ETDEWEB)

    1989-06-01

    The health and safety of its personnel is the first concern of ORNL and its management. The ORNL Health and Safety Program has the responsibility for ensuring the health and safety of all individuals assigned to ORNL activities. This document outlines the principal aspects of the ORNL Health and Safety Long-Range Plan and provides a framework for management use in the future development of the health and safety program. Each section of this document is dedicated to one of the health and safety functions (i.e., health physics, industrial hygiene, occupational medicine, industrial safety, nuclear criticality safety, nuclear facility safety, transportation safety, fire protection, and emergency preparedness). Each section includes functional mission and objectives, program requirements and status, a summary of program needs, and program data and funding summary. Highlights of FY 1988 are included.

  6. Oak Ridge National Laboratory Health and Safety Long-Range Plan: Fiscal years 1989--1995

    International Nuclear Information System (INIS)

    1989-06-01

    The health and safety of its personnel is the first concern of ORNL and its management. The ORNL Health and Safety Program has the responsibility for ensuring the health and safety of all individuals assigned to ORNL activities. This document outlines the principal aspects of the ORNL Health and Safety Long-Range Plan and provides a framework for management use in the future development of the health and safety program. Each section of this document is dedicated to one of the health and safety functions (i.e., health physics, industrial hygiene, occupational medicine, industrial safety, nuclear criticality safety, nuclear facility safety, transportation safety, fire protection, and emergency preparedness). Each section includes functional mission and objectives, program requirements and status, a summary of program needs, and program data and funding summary. Highlights of FY 1988 are included

  7. Food safety security: a new concept for enhancing food safety measures.

    Science.gov (United States)

    Iyengar, Venkatesh; Elmadfa, Ibrahim

    2012-06-01

    The food safety security (FSS) concept is perceived as an early warning system for minimizing food safety (FS) breaches, and it functions in conjunction with existing FS measures. Essentially, the function of FS and FSS measures can be visualized in two parts: (i) the FS preventive measures as actions taken at the stem level, and (ii) the FSS interventions as actions taken at the root level, to enhance the impact of the implemented safety steps. In practice, along with FS, FSS also draws its support from (i) legislative directives and regulatory measures for enforcing verifiable, timely, and effective compliance; (ii) measurement systems in place for sustained quality assurance; and (iii) shared responsibility to ensure cohesion among all the stakeholders namely, policy makers, regulators, food producers, processors and distributors, and consumers. However, the functional framework of FSS differs from that of FS by way of: (i) retooling the vulnerable segments of the preventive features of existing FS measures; (ii) fine-tuning response systems to efficiently preempt the FS breaches; (iii) building a long-term nutrient and toxicant surveillance network based on validated measurement systems functioning in real time; (iv) focusing on crisp, clear, and correct communication that resonates among all the stakeholders; and (v) developing inter-disciplinary human resources to meet ever-increasing FS challenges. Important determinants of FSS include: (i) strengthening international dialogue for refining regulatory reforms and addressing emerging risks; (ii) developing innovative and strategic action points for intervention {in addition to Hazard Analysis and Critical Control Points (HACCP) procedures]; and (iii) introducing additional science-based tools such as metrology-based measurement systems.

  8. 76 FR 40733 - National Institute for Occupational Safety and Health, (NIOSH), World Trade Center Health Program...

    Science.gov (United States)

    2011-07-11

    ... DEPARTMENT OF HEALTH AND HUMAN SERVICES Centers for Disease Control and Prevention National Institute for Occupational Safety and Health, (NIOSH), World Trade Center Health Program Science/Technical Advisory Committee (WTCHP-STAC) Correction: This notice was published in the Federal Register on June 23...

  9. Assessing systemwide occupational health and safety risks of energy technologies

    International Nuclear Information System (INIS)

    Rowe, M.D.

    1982-01-01

    Input-output modelling is now being used to assess systemwide occupational and public health and safety risks of energy technologies. Some of the advantages and disadvantages of this method are presented and some of its important limitations are discussed. Its primary advantage is that it provides a standard method with which to compare technologies on a consistent basis without extensive economic analysis. Among the disadvantages are limited range of applicability, limited spectrum of health impacts, and inability to identify unusual health impacts unique to a new technology. (author)

  10. Occupational health and safety among commercial sex workers.

    Science.gov (United States)

    Ross, Michael W; Crisp, Beth R; Månsson, Sven-Axel; Hawkes, Sarah

    2012-03-01

    The concept of occupational health and safety (OHS) for commercial sex workers has rarely been investigated, perhaps because of the often informal nature of the workplace, the associated stigma, and the frequently illegal nature of the activity. We reviewed the literature on health, occupational risks, and safety among commercial sex workers. Cultural and local variations and commonalities were identified. Dimensions of OHS that emerged included legal and policing risks, risks associated with particular business settings such as streets and brothels, violence from clients, mental health risks and protective factors, alcohol and drug use, repetitive strain injuries, sexually transmissible infections, risks associated with particular classes of clients, issues associated with male and transgender commercial sex workers, and issues of risk reduction that in many cases are associated with lack of agency or control, stigma, and legal barriers. We further discuss the impact and potential of OHS interventions for commercial sex workers. The OHS of commercial sex workers covers a range of domains, some potentially modifiable by OHS programs and workplace safety interventions targeted at this population. We argue that commercial sex work should be considered as an occupation overdue for interventions to reduce workplace risks and enhance worker safety.

  11. Management capacity to promote nurse workplace health and safety.

    Science.gov (United States)

    Fang, Yaxuan; McDonald, Tracey

    2018-04-01

    To investigate regarding workplace health and safety factors, and to identify strategies to preserve and promote a healthy nursing workplace. Data collected using the Delphi technique with input from 41 key informants across four participant categories drawn from a Chinese university and four hospitals were thematically analysed. Most respondents agreed on the importance of nurses' health and safety, and that nurse managers should act to protect nurses, but not enough on workplace safety. Hospital policies, staff disempowerment, workload and workplace conflicts are major obstacles. The reality of Chinese nurses' workplaces is that health and safety risks abound and relate to socio-cultural expectations of women. Self-management of risks is neccessary, gaps exist in understanding of workplace risks among different nursing groups and their perceptions of the professional status, and the value of nurses' contribution to ongoing risks in the hospital workplace. The Chinese hospital system must make these changes to produce a safer working environment for nurses. This research, based in China, presents an instructive tale for all countries that need support on the types and amounts of management for nurses working at the clinical interface, and on the consequences of management neglect of relevant policies and procedures. © 2017 John Wiley & Sons Ltd.

  12. Foundational workplace safety and health competencies for the emerging workforce☆

    Science.gov (United States)

    Okun, Andrea H.; Guerin, Rebecca J.; Schulte, Paul A.

    2016-01-01

    Introduction Young workers (aged 15–24) suffer disproportionately from workplace injuries, with a nonfatal injury rate estimated to be two times higher than among workers age 25 or over. These workers make up approximately 9% of the U.S. workforce and studies have shown that nearly 80% of high school students work at some point during high school. Although young worker injuries are a pressing public health problem, the critical knowledge and skills needed to prepare youth for safe and healthy work are missing from most frameworks used to prepare the emerging U.S. workforce. Methods A framework of foundational workplace safety and health knowledge and skills (the NIOSH 8 Core Competencies)was developed based on the Health Belief Model (HBM). Results The proposed NIOSH Core Competencies utilize the HBM to provide a framework for foundational workplace safety and health knowledge and skills. An examination of how these competencies and the HBM apply to actions that workers take to protect themselves is provided. The social and physical environments that influence these actions are also discussed. Conclusions The NIOSH 8 Core Competencies, grounded in one of the most widely used health behavior theories, fill a critical gap in preparing the emerging U.S. workforce to be cognizant of workplace risks. Practical applications Integration of the NIOSH 8 Core Competencies into school curricula is one way to ensure that every young person has the foundational workplace safety and health knowledge and skills to participate in, and benefit from, safe and healthy work. National Safety Council and Elsevier Ltd. All rights reserved. PMID:27846998

  13. Occupational health and safety inspection of the Ranger Uranium Mine

    International Nuclear Information System (INIS)

    Rosen, R.

    1987-04-01

    The principal purpose of the inspection was to assess all aspects of occupational health and safety at the Ranger Uranium Mine. A major objective was to identify actual and potential hazards under normal and abnormal conditions, particularly in relation to those topics about which the unions had expressed some concern. An assessment was made of current safety policies, procedures and practices at the site; and, as far as practicable, those tasks which involved risks to workers were identified. The results and recommendations of the inspection are contained in this report

  14. What do health professionals think about patient safety?

    OpenAIRE

    Hindle, Don; Haraga, Simona; Radu, Ciprian Paul; Yazbeck, Anne-Marie

    2008-01-01

    Artikkel som besrkiver en studie hvor hensikten var å undersøke helsepersonell sitt syn på pasientsikkerhet i sykehus i Romania, og sammenligne funnene med resultater fra Norge, Sverige, Singapor og Australia. Patient safety is a main determinant of the quality of healthcare services. The literature shows that the occurrence of medical errors is quite important in countries where it has been measured. Various actions like legislative measures, financial, or educational measures may help, b...

  15. Inherent and passive safety measures in accelerator driven systems: a safety strategy for ADS

    International Nuclear Information System (INIS)

    Maschek, W.; Rineiski, A.; Morita, K.; Flad, M.

    2001-01-01

    The efficiency of Accelerator Driven Systems (ADSs) for the transmutation and incineration of nuclear waste is strongly related to the utilization of so-called dedicated fuels. In the ideal case these fuels should consist of pure TRUs without fertile materials as 238 U or 232 Th to achieve highest incineration/transmutation rates. Dedicated fuels still have to be developed and programs are under way for their fabrication, irradiation and testing. These fertile-free fuels may suffer from deteriorated thermal or thermo-mechanical properties, as a reduced melting point, reduced thermal conductivity or even thermal instability. First analyses have shown that the use of dedicated fuels may lead to a strong deterioration of the safety parameters of the reactor core as e.g. the void worth, the Doppler or the kinetics quantities as neutron generation time and β eff . In addition, a dedicated core may contain multiple ''critical'' fuel masses, resulting in a considerable recriticality potential. Current knowledge on these dedicated fuels suggests that ''critical'' reactors may not be feasible, because of safety reasons. However, for ADSs, the salient hope has been promoted that due to the subcriticality of the system the poor safety features of such fuels could be coped with. Analyses are presented which show potential safety problems for such dedicated cores. Respecting the results of these analyses a safety strategy is proposed along the lines of defense approach in analogy with ideas formerly developed for fast reactors. Inherent and passive safety measures are integrated into the various defense lines. (author)

  16. Measures for reinforcing safety at the Ohma Nuclear Power Plant

    International Nuclear Information System (INIS)

    Ishikawa, Hiroyasu; Iwata, Kichisa; Koga, Kaoru

    2013-01-01

    Electric Power Development Co., Ltd. ('J-POWER') has been moving ahead with the Ohma Nuclear Power Project at Ohma-machi, Shimokita-gun in Aomori Prefecture and commenced the construction of an Advanced Boiling Water Reactor (ABWR) in May 2008. In light of the Fukushima Daiichi Nuclear Power Station Incident, J-POWER has undertaken an investigation of various measures for reinforcing safety at the Ohma nuclear power plant. These measures include a range of anti-tsunami measures, measures to ensure emergency power sources and ultimate heat removal functions, and responses for severe accidents. While consistently and properly reflecting the necessary measures, J-POWER will continue to ensure the creation of a safe power plant. J-POWER intends to appropriately reflect at all times new standards of technology established by the Nuclear Regulation Authority and makes concerted efforts to build a safe nuclear power plant in which the local community can have confidence. (author)

  17. FMCSA safety program effectiveness measurement : carrier intervention effectiveness model, version 1.0 : [analysis brief].

    Science.gov (United States)

    2015-01-01

    The Carrier Intervention Effectiveness Model (CIEM) : provides the Federal Motor Carrier Safety : Administration (FMCSA) with a tool for measuring : the safety benefits of carrier interventions conducted : under the Compliance, Safety, Accountability...

  18. Agricultural Health and Safety Survey in Friuli Venezia Giulia

    Directory of Open Access Journals (Sweden)

    Sirio Rossano Secondo Cividino

    2018-01-01

    Full Text Available The work in the agricultural sector has taken on a fundamental role in the last decades, due to the still too high rate of fatal injuries, workplace accidents, and dangerous occurrences reported each year. The average old age of agricultural machinery is one of the main issues at stake in Italy. Numerous safety problems stem from that; therefore, two surveys were conducted in two different periods, on current levels of work safety in agriculture in relation to agricultural machinery’s age and efficiency, and to show the levels of actual implementation of the Italian legislation on safety and health at work in the agricultural sector. The surveys were carried out, considering a sample of 161 farms located in the region Friuli Venezia Giulia (North-East of Italy. The research highlights the most significant difficulties the sample of farms considered have in enforcing the law. One hand, sanitary surveillance and workers’ information and training represent the main deficiencies and weakest points in family farms. Moreover, family farms do not generally provide the proper documentation concerning health and safety at workplaces, when they award the contract to other companies. On the other hand, lack of maintenance program for machinery and equipment, and of emergency plans and participation of workers’ health and safety representative, are the most common issues in farms with employees. Several difficulties are also evident in planning workers’ training programs. Furthermore, the company physician’s task is often limited to medical controls, so that he is not involved in risk assessment and training. Interviews in heterogeneous samples of farms have shown meaningful outcomes, which have subsequently been used to implement new databases and guidelines for Health and Safety Experts and courses in the field of Work Safety in agriculture. In conclusion, although the legislation making training courses for tractor operators and tractor

  19. Linking Environmental Sustainability, Health, and Safety Data in Health Care: A Research Roadmap.

    Science.gov (United States)

    Kaplan, Susan B; Forst, Linda

    2017-08-01

    Limited but growing evidence demonstrates that environmental sustainability in the health-care sector can improve worker and patient health and safety. Yet these connections are not appreciated or understood by decision makers in health-care organizations or oversight agencies. Several studies demonstrate improvements in quality of care, staff satisfaction, and work productivity related to environmental improvements in the health-care sector. A pilot study conducted by the authors found that already-collected data could be used to evaluate impacts of environmental sustainability initiatives on worker and patient health and safety, yet few hospitals do so. Future research should include a policy analysis of laws that could drive efforts to integrate these areas, elucidation of organizational models that promote sharing of environmental and health and safety data, and development of tools and methods to enable systematic linkage and evaluation of these data to expand the evidence base and improve the hospital environment.

  20. Effects of a Workplace Intervention Targeting Psychosocial Risk Factors on Safety and Health Outcomes

    Directory of Open Access Journals (Sweden)

    Leslie B. Hammer

    2015-01-01

    Full Text Available The goal of this study was to test the effectiveness of a workplace intervention targeting work-life stress and safety-related psychosocial risk factors on health and safety outcomes. Data were collected over time using a randomized control trial design with 264 construction workers employed in an urban municipal department. The intervention involved family- and safety-supportive supervisor behavior training (computer-based, followed by two weeks of behavior tracking and a four-hour, facilitated team effectiveness session including supervisors and employees. A significant positive intervention effect was found for an objective measure of blood pressure at the 12-month follow-up. However, no significant intervention results were found for self-reported general health, safety participation, or safety compliance. These findings suggest that an intervention focused on supervisor support training and a team effectiveness process for planning and problem solving should be further refined and utilized in order to improve employee health with additional research on the beneficial effects on worker safety.