WorldWideScience

Sample records for hb-line scrap recovery

  1. Solids loading evaluation for HB-line scrap recovery filters

    International Nuclear Information System (INIS)

    Crowder, M.L.

    2000-01-01

    The HB-Line Scrap Recovery facility uses wire screen filters to remove solids from plutonium-containing solutions transferred from the slab tank dissolvers. At times, the accumulation of solids is large enough to cause blinding (i.e., pluggage) of the filters. If the solids contain undissolved plutonium, significant accumulation of fissile material could impact operations. To address this potential issue, experiments were performed to define the minimum solids required to completely blind a filter. The solids loading experiments were performed by arranging 25- and 10-microm HB-Line filters in series to simulate the equipment in the scrap recovery process. Separate tests were performed using coarse and fine glass frit and cerium oxide powder suspended in 35 wt% sodium nitrate solution using a small turbine mixer. The solution and solids were transferred from a reservoir through the filter housings by vacuum. In each case, the 25-microm filter blinded first and was full of wet cake. After drying and accounting for the sodium nitrate in the filter cake, the following results were obtained. The results of the solids loading tests demonstrated that at least 800 g of solids accumulated in the filter housing before flow stopped. The actual amount of collected material was dependent upon the physical properties of the solids such as density and particle size. The mass of solids collected by the blinded 25-microm filter increased when successively finer solids were used in the experiments. Based on these results, one should anticipate that filters in the HB-Line Scrap Recovery Facility have the potential to collect similar quantities of material before transfer of solution from the dissolvers is severely impacted

  2. Safety analysis, 200 Area, Savannah River Plant: Separations area operations. Building 221-H, B-Line, Scrap Recovery Facility (Supplement 2A): Revision 1

    Energy Technology Data Exchange (ETDEWEB)

    None

    1991-07-01

    The now HB-Line is located an top of the 221-H Building on the fifth and sixth levels and is designed to replace the aging existing HB-Line production facility. The new HB-Line consists of three separate facilities: the Scrap Recovery Facility, Neptunium Facility, and Plutonium Oxide Facility. The Scrap Recovery Facility is designed to routinely generate nitrate solutions of {sup 235}U{sup 239}Pu and Pu-238 fromscrap for purification by anion exchange or by solvent extraction in the canyon. The now facility incorporates improvements in: (1) engineered controls for nuclear criticality, (2) cabinet integrity and engineered barriers to contain contamination and minimize personnel exposure to airborne contamination, (3) shielding and remote operations to decrease radiation exposure, and (4) equipment and ventilation design to provide flexibility and improved process performance.

  3. Capability to Recover Plutonium-238 in H-Canyon/HB-Line - 13248

    Energy Technology Data Exchange (ETDEWEB)

    Fuller, Kenneth S. Jr.; Smith, Robert H. Jr.; Goergen, Charles R. [Savannah River Nuclear Solutions, LLC, Savannah River Site, Aiken, SC 29802 (United States)

    2013-07-01

    Plutonium-238 is used in Radioisotope Thermoelectric Generators (RTGs) to generate electrical power and in Radioisotope Heater Units (RHUs) to produce heat for electronics and environmental control for deep space missions. The domestic supply of Pu-238 consists of scrap material from previous mission production or material purchased from Russia. Currently, the United States has no significant production scale operational capability to produce and separate new Pu-238 from irradiated neptunium-237 targets. The Department of Energy - Nuclear Energy is currently evaluating and developing plans to reconstitute the United States capability to produce Pu-238 from irradiated Np-237 targets. The Savannah River Site had previously produced and/or processed all the Pu-238 utilized in Radioisotope Thermoelectric Generators (RTGs) for deep space missions up to and including the majority of the plutonium for the Cassini Mission. The previous full production cycle capabilities included: Np- 237 target fabrication, target irradiation, target dissolution and Np-237 and Pu-238 separation and purification, conversion of Np-237 and Pu-238 to oxide, scrap recovery, and Pu-238 encapsulation. The capability and equipment still exist and could be revitalized or put back into service to recover and purify Pu-238/Np-237 or broken General Purpose Heat Source (GPHS) pellets utilizing existing process equipment in HB-Line Scrap Recovery, and H-Canyon Frame Waste Recovery processes. The conversion of Np-237 and Pu-238 to oxide can be performed in the existing HB-Line Phase-2 and Phase- 3 Processes. Dissolution of irradiated Np-237 target material, and separation and purification of Np-237 and Pu-238 product streams would be possible at production rates of ∼2 kg/month of Pu-238 if the existing H-Canyon Frames Process spare equipment were re-installed. Previously, the primary H-Canyon Frames equipment was removed to be replaced: however, the replacement project was stopped. The spare equipment

  4. HB-Line Material Control and Accountability Measurements at SRS

    International Nuclear Information System (INIS)

    Casella, V.R.

    2003-01-01

    Presently, HB-Line work at the Savannah River Site consists primarily of the stabilization and packaging of nuclear materials for storage and the characterization of materials for disposition in H-Area. In order to ensure compliance with Material Control and Accountability (MC and A) Regulations, accountability measurements are performed throughout the HB-Line processes. Accountability measurements are used to keep track of the nuclear material inventory by constantly updating the amount of material in the MBAs (Material Balance Area) and sub-MBAs. This is done by subtracting the amount of accountable material that is added to a process and by adding the amount of accountable material that is put back in storage. A Physical Inventory is taken and compared to the ''Book Value'' listed in the Nuclear Material Accounting System. The difference (BPID) in the Book Inventory minus the Physical Inventory of a sub-account for bulk material must agree within the measurement errors combined in quadrature to provide assurance that nuclear material is accounted for. This work provides an overview of HB-Line processes and accountability measurements. The Scrap Recovery Line and Neptunium-237/Plutonium-239 Oxide Line are described and sampling and analyses for Phase II are provided. Recommendations for improvements are provided to improve efficiency and cost effectiveness

  5. HB-Line Dissolver Dilution Flows and Dissolution Capability with Dissolver Charge Chute Cover Off

    International Nuclear Information System (INIS)

    Hallman, D.F.

    2003-01-01

    A flow test was performed in Scrap Recovery of HB-Line to document the flow available for hydrogen dilution in the dissolvers when the charge chute covers are removed. Air flow through the dissolver charge chutes, with the covers off, was measured. A conservative estimate of experimental uncertainty was subtracted from the results. After subtraction, the test showed that there is 20 cubic feet per minute (cfm) air flow through the dissolvers during dissolution with a glovebox exhaust fan operating, even with the scrubber not operating. This test also showed there is 6.6 cfm air flow through the dissolvers, after subtraction of experimental uncertainty if the scrubber and the glovebox exhaust fans are not operating. Three H-Canyon exhaust fans provide sufficient motive force to give this 6.6 cfm flow. Material charged to the dissolver will be limited to chemical hydrogen generation rates that will be greater than or equal to 25 percent of the Lower Flammability Limit (LFL) during normal operations. The H-Canyon fans will maintain hydrogen below LFL if electrical power is lost. No modifications are needed in HB-Line Scrap Recovery to ensure hydrogen is maintained less that LFL if the scrubber and glovebox exhaust fans are not operating

  6. Testing of wet scrap recovery equipment for mixed oxide scrap reprocessing

    International Nuclear Information System (INIS)

    Demiter, J.A.; Klem, M.J.; Owen, T.J.

    1984-08-01

    The Wet Scrap Recovery (WSR) program was initiated at the Hanford Engineering Development Laboratory (HEDL) by Westinghouse Hanford Company in Richland, Washington to demonstrate fuel fabrication scrap recovery and reconversion to fuel grade oxide powder using the continuous coprecipitation-calcination (COPRECAL) conversion process. Advancements in process control equipment and instrumentation were also developed and demonstrated

  7. Process options and projected mass flows for the HTGR refabrication scrap recovery system

    International Nuclear Information System (INIS)

    Tiegs, S.M.

    1979-03-01

    The two major uranium recovery processing options reviewed are (1) internal recovery of the scrap by the refabrication system and (2) transfer to and external recovery of the scrap by the head end of the reprocessing system. Each option was reviewed with respect to equipment requirements, preparatory processing, and material accountability. Because there may be a high cost factor on transfer of scrap fuel material to the reprocessing system for recovery, all of the scrap streams will be recycled internally within the refabrication system, with the exception of reject fuel elements, which will be transferred to the head end of the reprocessing system for uranium recovery. The refabrication facility will be fully remote; thus, simple recovery techniques were selected as the reference processes for scrap recovery. Crushing, burning, and leaching methods will be used to recover uranium from the HTGR refabrication scrap fuel forms, which include particles without silicon carbide coatings, particles with silicon carbide coatings, uncarbonized fuel rods, carbon furnace parts, perchloroethylene distillation bottoms, and analytical sample remnants. Mass flows through the reference scrap recovery system were calculated for the HTGR reference recycle facility operating with the highly enriched uranium fuel cycle. Output per day from the refabrication scrap recovery system is estimated to be 4.02 kg of 2355 U and 10.85 kg of 233 U. Maximum equipment capacities were determined, and future work will be directed toward the development and costing of the scrap recovery system chosen as reference

  8. 41 CFR 109-27.5107 - Recovery of silver from used hypo solution and scrap film.

    Science.gov (United States)

    2010-07-01

    ... used hypo solution and scrap film. 109-27.5107 Section 109-27.5107 Public Contracts and Property... § 109-27.5107 Recovery of silver from used hypo solution and scrap film. The requirements for the recovery of silver from used hypo solution and scrap film are contained in § 109-45.1003 of this chapter. ...

  9. HB-Line Dissolution of Glovebox Floor Sweepings

    International Nuclear Information System (INIS)

    Gray, J.H.

    1998-02-01

    one to three hours.Generation of hydrogen caused by the dissolution of calcium metal should also not be a concern.No hydrogen was detected in the laboratory off-gas stream and insignificant metals of any kind are present in glovebox floor sweepings. Glovebox floor sweepings are generated at Savannah River in FB-Line during preparation of the feed material used in the metal producing bomb reduction process. It is usually after precipitation and during drying or conversion of plutonium fluoride to a PuF 4 -PuO 2 mixture at 500 degree C, that spil occur which can contaminate the converted cake with varying amounts of MgO sand or other glovebox materials. This contaminated converted cake mixture of PuF 4 and PuO 2 is packaged and stored in the vault fo eventual recovery of the plutonium.In the past, most recovery operations in HB-Line have dealt with PuO 2 as the only plutonium compound present in the material to be dissolved. However,since the plutonium in FB-Line glovebox floor sweepings is a mixture of plutonium fluoride (PuF 4 ) and plutonium oxide (PuO 2 ), the standar HB-Line dissolving flowsheet is not directly suitable for complete dissolution.This is because it is difficult to completely dissolve PuO 2 when the fluoride is complexed with aluminum and it is difficult to completely dissolve PuF 4 unless sufficient aluminum is present to complex free fluoride. These observations were previously confirmed during the initial flowsheet development work for dissolving sand, slag,

  10. HB-Line Plutonium Oxide Data Collection Strategy

    Energy Technology Data Exchange (ETDEWEB)

    Watkins, R. [Savannah River Nuclear Solutions; Varble, J. [Savannah River Nuclear Solutions; Jordan, J. [Savannah River Nuclear Solutions

    2015-05-26

    HB-Line and H-Canyon will handle and process plutonium material to produce plutonium oxide for feed to the Mixed Oxide Fuel Fabrication Facility (MFFF). However, the plutonium oxide product will not be transferred to the MFFF directly from HB-Line until it is packaged into a qualified DOE-STD-3013-2012 container. In the interim, HB-Line will load plutonium oxide into an inner, filtered can. The inner can will be placed in a filtered bag, which will be loaded into a filtered outer can. The outer can will be loaded into a certified 9975 with getter assembly in compliance with onsite transportation requirement, for subsequent storage and transfer to the K-Area Complex (KAC). After DOE-STD-3013-2012 container packaging capabilities are established, the product will be returned to HB-Line to be packaged into a qualified DOE-STD-3013-2012 container. To support the transfer of plutonium oxide to KAC and then eventually to MFFF, various material and packaging data will have to be collected and retained. In addition, data from initial HB-Line processing operations will be needed to support future DOE-STD-3013-2012 qualification as amended by the HB-Line DOE Standard equivalency. As production increases, the volume of data to collect will increase. The HB-Line data collected will be in the form of paper copies and electronic media. Paper copy data will, at a minimum, consist of facility procedures, nonconformance reports (NCRs), and DCS print outs. Electronic data will be in the form of Adobe portable document formats (PDFs). Collecting all the required data for each plutonium oxide can will be no small effort for HB-Line, and will become more challenging once the maximum annual oxide production throughput is achieved due to the sheer volume of data to be collected. The majority of the data collected will be in the form of facility procedures, DCS print outs, and laboratory results. To facilitate complete collection of this data, a traveler form will be developed which

  11. Efficient recovery of gold and other noble metals from electronic and other scraps

    Energy Technology Data Exchange (ETDEWEB)

    Baba, Hidetoshi

    1987-01-01

    Pure gold is extracted from crude gold by the solvent extraction method in the recovery and refining process for Noble metals recovered from electronic and other scraps. This solvent extraction method is advantageous in that it facilitates rapid processing, thereby reducing the interest burden of gold staying too long in the unit. Therefore, the method is also used in the refining of platinum and palladium. Technological innovation has created more complex and diversified types of scraps, and efforts are being made to accommodate ourselves to such a trend.

  12. Study of scrap recovery for mixed oxide pellet by means of UO2+5wt.%CeO2

    International Nuclear Information System (INIS)

    Joung, Chang Young; Kim, Si Hyung; Kim, Han Soo; Lee, Yong Woo

    2000-01-01

    The recovery method of scrap powder was established using UO 2 -5wt.%CeO 2 powder in the way of of technology development of scrap recovery and recycle in the mixed oxide pellet fabrication process. And pellet density and microstructure, which depend on quantity of scrap, powder treatment method, and sintering condition, was analyzed. As a result of oxidation of sintered pellet in the air the powdering at below 400 degrees C occurred smoothly, and at above 400 degrees C powdering process was not proceeding well as temperature increased and powder particle size grew bigger. M 3 O 8 scrap powder which was powdered through oxidation method was added to UO 2 -5wt.%CeO 2 mixed powder. The results after the powder was treated by means of mixing, crushing, attrition milling, pelletizing, and sintering showed that its density and grain size in the case of reductive sintering decreased as scrap addition increased, but the result in the case of crushing showed increase in grain size. In attrition milling case both density and grain size showed the tendency of increase, particularly grain size grew up to 12 μm. In the oxidative sintering with scrap added mixed powder sintering was accelerated under the oxygen environment and the effect of powder treatment showed the tendency of relatively decreasing. (Hong, J. S.)

  13. Lithium Carbonate Recovery from Cathode Scrap of Spent Lithium-Ion Battery: A Closed-Loop Process.

    Science.gov (United States)

    Gao, Wenfang; Zhang, Xihua; Zheng, Xiaohong; Lin, Xiao; Cao, Hongbin; Zhang, Yi; Sun, Zhi

    2017-02-07

    A closed-loop process to recover lithium carbonate from cathode scrap of lithium-ion battery (LIB) is developed. Lithium could be selectively leached into solution using formic acid while aluminum remained as the metallic form, and most of the other metals from the cathode scrap could be precipitated out. This phenomenon clearly demonstrates that formic acid can be used for lithium recovery from cathode scrap, as both leaching and separation reagent. By investigating the effects of different parameters including temperature, formic acid concentration, H 2 O 2 amount, and solid to liquid ratio, the leaching rate of Li can reach 99.93% with minor Al loss into the solution. Subsequently, the leaching kinetics was evaluated and the controlling step as well as the apparent activation energy could be determined. After further separation of the remaining Ni, Co, and Mn from the leachate, Li 2 CO 3 with the purity of 99.90% could be obtained. The final solution after lithium carbonate extraction can be further processed for sodium formate preparation, and Ni, Co, and Mn precipitates are ready for precursor preparation for cathode materials. As a result, the global recovery rates of Al, Li, Ni, Co, and Mn in this process were found to be 95.46%, 98.22%, 99.96%, 99.96%, and 99.95% respectively, achieving effective resources recycling from cathode scrap of spent LIB.

  14. A model for recovery of scrap monolithic uranium molybdenum fuel by electrorefining

    Science.gov (United States)

    Van Kleeck, Melissa A.

    The goal of the Reduced Enrichment for Research and Test Reactors program (RERTR) is toreduce enrichment at research and test reactors, thereby decreasing proliferation risk at these facilities. A new fuel to accomplish this goal is being manufactured experimentally at the Y12 National Security Complex. This new fuel will require its own waste management procedure,namely for the recovery of scrap from its manufacture. The new fuel is a monolithic uraniummolybdenum alloy clad in zirconium. Feasibility tests were conducted in the Planar Electrode Electrorefiner using scrap U-8Mo fuel alloy. These tests proved that a uranium product could be recovered free of molybdenum from this scrap fuel by electrorefining. Tests were also conducted using U-10Mo Zr clad fuel, which confirmed that product could be recovered from a clad version of this scrap fuel at an engineering scale, though analytical results are pending for the behavior of Zr in the electrorefiner. A model was constructed for the simulation of electrorefining the scrap material produced in the manufacture of this fuel. The model was implemented on two platforms, Microsoft Excel and MatLab. Correlations, used in the model, were developed experimentally, describing area specific resistance behavior at each electrode. Experiments validating the model were conducted using scrap of U-10Mo Zr clad fuel in the Planar Electrode Electrorefiner. The results of model simulations on both platforms were compared to experimental results for the same fuel, salt and electrorefiner compositions and dimensions for two trials. In general, the model demonstrated behavior similar to experimental data but additional refinements are needed to improve its accuracy. These refinements consist of a function for surface area at anode and cathode based on charge passed. Several approximations were made in the model concerning areas of electrodes which should be replaced by a more accurate function describing these areas.

  15. Cost-assessment Analysis of Local Vehicle Scrapping Facility

    Science.gov (United States)

    Grabowski, Lukasz; Gliniak, Maciej; Polek, Daria; Gruca, Maria

    2017-12-01

    The purpose of the paper was to analyse the costs of recycling vehicles at local vehicle scrapping facility. The article contains regulations concerning vehicle decommissioning, describes the types of recovery, vehicles recycling networks, analyses the structure of a disassembly station, as well as the financial and institutional system in charge of dealing with the recycling of vehicles in Poland. The authors present the number of scrapped vehicles at local recycling company and the level of achieved recovery and recycling. The research presented in the article shows financial situation of the vehicle scrapping industry. In addition, it has been observed that the number of subsidies are directly proportional to the number of scrapped vehicles, and achieved levels of recycling and recovery depends on the percentage of incomplete vehicles.

  16. Environmental assessment operation of the HB-Line facility and frame waste recovery process for production of Pu-238 oxide at the Savannah River Site

    International Nuclear Information System (INIS)

    1995-04-01

    The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA-0948, addressing future operations of the HB-Line facility and the Frame Waste Recovery process at the Savannah River Site (SRS), near Aiken, South Carolina. Based on the analyses in the EA, DOE has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, DOE has concluded that, the preparation of an environmental impact statement is not required, and is issuing this Finding of No Significant Impact

  17. Development of a recovery process of scraps resulting from the manufacture of metallic uranium fuels

    International Nuclear Information System (INIS)

    Camilo, Ruth L.; Kuada, Terezinha A.; Forbicini, Christina A.L.G.O.; Cohen, Victor H.; Araujo, Bertha F.; Lobao, Afonso S.T.

    1996-01-01

    The study of the dissolution of natural metallic uranium fuel samples with aluminium cladding is presented, in order to obtain optimized conditions for the system. The aluminium cladding was dissolved in an alkaline solution of Na OH/Na NO 3 and the metallic uranium with HNO 3 . A fumeless dissolution with total recovery of nitrous gases was achieved. The main purpose of this project was the recovery of uranium from scraps resulting from the manufacture of the metallic uranium fuel or other non specified fuels. (author)

  18. Leaching behaviour of different scrap materials at recovery and recycling companies: full-, pilot- and lab-scale investigation.

    Science.gov (United States)

    Blondeel, E; Chys, M; Depuydt, V; Folens, K; Du Laing, G; Verliefde, A; Van Hulle, S W H

    2014-12-01

    Scrap material recovery and recycling companies are confronted with waste water that has a highly fluctuating flow rate and composition. Common pollutants, such as COD, nutrients and suspended solids, potentially toxic metals, polyaromatic hydrocarbons and poly chlorinated biphenyls can exceed the discharge limits. An analysis of the leaching behaviour of different scrap materials and scrap yard sweepings was performed at full-scale, pilot-scale and lab-scale in order to find possible preventive solutions for this waste water problem. The results of these leaching tests (with concentrations that frequently exceeded the Flemish discharge limits) showed the importance of regular sweeping campaigns at the company, leak proof or covered storage of specific scrap materials and oil/water separation on particular leachates. The particulate versus dissolved fraction was also studied for the pollutants. For example, up to 98% of the polyaromatic hydrocarbons, poly chlorinated biphenyls and some metals were in the particulate form. This confirms the (potential) applicability of sedimentation and filtration techniques for the treatment of the majority of the leachates, and as such the rainwater run-off as a whole. Copyright © 2014 Elsevier Ltd. All rights reserved.

  19. Radioisotope Characterization of HB Line Low Activity Waste

    International Nuclear Information System (INIS)

    Snyder, S.J.

    1999-01-01

    The purpose of this document is to provide a physical, chemical, hazardous and radiological characterization of Low-Level Waste (LLW) generated in HB-Line as required by the 1S Manual, Savannah River Site Waste Acceptance Criteria Manual

  20. Process evaluations for uranium recovery from scrap material

    International Nuclear Information System (INIS)

    Westphal, B.R.; Benedict, R.W.

    1992-01-01

    The integral Fast Reactor (IFR) concept being developed by Argonne National Laboratory is based on pyrometallurgical processing of spent nuclear metallic fuel with subsequent fabrication into new reactor fuel by an injection casting sequence. During fabrication, a dilute scrap stream containing uranium alloy fines and broken quartz (Vycor) molds in produced. Waste characterization of this stream, developed by using present operating data and chemical analysis was used to evaluate different uranium recovery methods and possible process variations for the return of the recovered metal. Two methods, comminution with size separation and electrostatic separation, have been tested and can recover over 95% of the metal. Recycling the metal to either the electrochemical process or the injection casting was evaluated for the different economic and process impacts. The physical waste parameters and the important separation process variables are discussed with their effects on the viability of recycling the material. In this paper criteria used to establish the acceptable operating limits is discussed

  1. Recovery of gold from electronic scrap by hydrometallurgical processes

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Churl Kyoung; Rhee, Kang-In [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of); Sohn, Hun Joon [Seoul National University, Seoul (Korea, Republic of)

    1997-09-30

    A series of processes has been developed to recover the gold from electronic scrap containing about 200{approx}600 ppm Au. First, mechanical beneficiation including shredding, crushing and screening was employed. Results showed that 99 percent of gold component leaves in the fraction of under 1 mm of crushed scrap and its concentration was enriched to about 800 ppm without incineration. The crushed scrap was leached in 50% aqua regia solution and gold was completely dissolved at 60 deg. C within 2 hours. Other valuable metals such as silver, copper, nickel and iron were also dissolved. The resulting solution was boiled to remove nitrous compounds in the leachate. Finally, a newly designed electrolyzer was tested to recover the gold metal. More than 99% of gold and silver were recovered within an hour by electrowinning process. (author). 10 refs., 5 tabs., 6 figs.

  2. Effect of Acid Dissolution Conditions on Recovery of Valuable Metals from Used Plasma Display Panel Scrap

    Directory of Open Access Journals (Sweden)

    Kim Chan-Mi

    2017-06-01

    Full Text Available The objective of this particular study was to recover valuable metals from waste plasma display panels using high energy ball milling with subsequent acid dissolution. Dissolution of milled (PDP powder was studied in HCl, HNO3, and H2SO4 acidic solutions. The effects of dissolution acid, temperature, time, and PDP scrap powder to acid ratio on the leaching process were investigated and the most favorable conditions were found: (1 valuable metals (In, Ag, Mg were recovered from PDP powder in a mixture of concentrated hydrochloric acid (HCl:H2O = 50:50; (2 the optimal dissolution temperature and time for the valuable metals were found to be 60°C and 30 min, respectively; (3 the ideal PDP scrap powder to acid solution ratio was found to be 1:10. The proposed method was applied to the recovery of magnesium, silver, and indium with satisfactory results.

  3. Nondestructive assay system development for a plutonium scrap recovery facility

    International Nuclear Information System (INIS)

    Hsue, S.T.; Baker, M.P.

    1984-01-01

    A plutonium scrap recovery facility is being constructed at the Savannah River Plant (SRP). The safeguards groups of the Los Alamos National Laboratory have been working since the early design stage of the facility with SRP and other national laboratories to develop a state-of-the-art assay system for this new facility. Not only will the most current assay techniques be incorporated into the system, but also the various nondestructive assay (NDA) instruments are to be integrated with an Instrument Control Computer (ICC). This undertaking is both challenging and ambitious; an entire assay system of this type has never been done before in a working facility. This paper will describe, in particular, the effort of the Los Alamos Safeguards Assay Group in this endeavor. Our effort in this project can be roughly divided into three phases: NDA development, system integration, and integral testing. 6 references

  4. State of the art of smelting lead-acid battery scrap

    Energy Technology Data Exchange (ETDEWEB)

    Melin, A

    1977-02-01

    A discussion is given of the economic importance of lead recovery and of scrap recycling in the battery industry. Various possibiliies of processing battery scrap, either by direct smelting or by smelting after preparaton are discussed, and the BBU, the Stolberger, and the Tonnolli methods are compared

  5. Dilution Ratios for HB Line Phase I Eductor System

    International Nuclear Information System (INIS)

    Steimke, J.L.

    2002-01-01

    HB Line Phase I product transfer includes an eductor which transfers liquid from Product Hold Tank (PHT) RT-33 or RT-34 to Tank 11.1. The eductor also dilutes the liquid from the PHT with eductant. Dilution must be reliably controlled because of criticality concerns with H Canyon Tanks. The eductor system, which contains a 1 inch Model 264 Schutte and Koerting eductor, was previously modeled [1] in 1998 and dilution ratios were calculated for different flow restrictors, eductant pressures and densities for the eductant and the contents of the PHT. The previous calculation was performed using spreadsheet software no longer supported at SRS. For the previous work dilution ratio was defined as the volume of eductant consumed divided by volume of PHT contents transferred. Since 1998 HB Line Engineering has changed the definition of dilution ratio to the total volume of liquid, eductant consumed plus the volume of PHT liquid transferred, divided by the volume of PHT liquid transferred. The 1998 base case calculation was for a restrictor diameter of 0.334 inches, an eductant supply pressure of 15 psig, full PHT, an eductant specific gravity of 1.385 and a PHT density of 1.015. The base case dilution ratio calculated in 1998 using the current definition was 3.52. After accounting for uncertainty the minimum dilution ratio decreased to 3.23. In 2001 HB Line Engineering requested that the calculation be repeated for a manganous nitrate solution eductant and also a process water eductant. The other conditions were the same as for the 1998 calculation. The objective of this report is to document the calculations and the results

  6. Energy Recovery from Scrap Tires: A Sustainable Option for Small Islands like Puerto Rico

    Directory of Open Access Journals (Sweden)

    Eddie N. Laboy-Nieves

    2014-05-01

    Full Text Available Puerto Rico generates and disposes nearly five million/year scrap tires (ST, of which 4.2% is recycled and 80% is exported. The Island has one of the world highest electrical service tariff ($0.28 kWh, because of its dependency on fossil fuels for power generation. The Government has not considered ST for electricity production, despite more than 13,000 ST are generated daily, and paradoxically exported for that purpose. Theoretically, if ST recycling increases to 10% and assuming that the caloric value of ST be 33 MJ/kg, it was estimated that scrap tires processed with pyrolysis can supply annually about 379 MWh, a potential value that shall not be unnoticed. This paper is a literature review to describe the legal, technical, and economic framework for the viability of ST for power generation in Puerto Rico using pyrolysis, the most recommended process for ST energy recovery. Data of ST from Puerto Rico was used to model the potential of ST for pyrolytic energy conversion. The herein article is intended to invite other insular countries and territories, to join efforts with the academic and scientific community, and with the energy generation sector, to validate ST as a sustainable option for energy generation.

  7. Contaminated nickel scrap processing

    International Nuclear Information System (INIS)

    Compere, A.L.; Griffith, W.L.; Hayden, H.W.; Johnson, J.S. Jr.; Wilson, D.F.

    1994-12-01

    The DOE will soon choose between treating contaminated nickel scrap as a legacy waste and developing high-volume nickel decontamination processes. In addition to reducing the volume of legacy wastes, a decontamination process could make 200,000 tons of this strategic metal available for domestic use. Contaminants in DOE nickel scrap include 234 Th, 234 Pa, 137 Cs, 239 Pu (trace), 60 Co, U, 99 Tc, and 237 Np (trace). This report reviews several industrial-scale processes -- electrorefining, electrowinning, vapormetallurgy, and leaching -- used for the purification of nickel. Conventional nickel electrolysis processes are particularly attractive because they use side-stream purification of process solutions to improve the purity of nickel metal. Additionally, nickel purification by electrolysis is effective in a variety of electrolyte systems, including sulfate, chloride, and nitrate. Conventional electrorefining processes typically use a mixed electrolyte which includes sulfate, chloride, and borate. The use of an electrorefining or electrowinning system for scrap nickel recovery could be combined effectively with a variety of processes, including cementation, solvent extraction, ion exchange, complex-formation, and surface sorption, developed for uranium and transuranic purification. Selected processes were reviewed and evaluated for use in nickel side-stream purification. 80 refs

  8. Investment recovery program at Niagara Mohawk Power Corporation

    International Nuclear Information System (INIS)

    Kotcamp, R.T.

    1993-01-01

    Niagara Mohawk Power Company's pioneering investment recovery program was initiated in 1984, Its mission is to dispose of company assets classified as obsolete, scrap, surplus, or retired capital equipment that results from company operations or work projects. These assets include items such as scrap wire, pipe, line hardware, transformers, power station equipment, crates of dusty telephone modems and computer monitors, pallets of residential gas and electric meters, a box of toilet paper holders, burned-out light bulbs, chunks of electric cable, brass and copper valves, electric bills from 1952, and a dozen tattered office chairs. It was risky for Niagara Mohawk to commit money to a program that created a scrap company inside a utility and is not the core business. No one regrets the decision to create and expand investment recovery. The program has contributed more than $35,000,000 ($8,140,585 nuclear division) of cash receipts with an additional $5,000,000 of cost avoidance since its inception. The program has credited these dollars back to the operating departments, which has reduced operating costs thereby improving the open-quotes bottom line.close quotes

  9. The development of technology for recycling of electronic scrap

    Energy Technology Data Exchange (ETDEWEB)

    Yu, Hyo-Shin; Kim, Won-Baek; Sohn, Yong-Uhn [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

    1999-12-01

    Electronic devices, especially computer becomes an essential tools for home and industries entering the information era. The number of computers exceed over 100 million, hence, the amount of end of life(EOL) computer and electronic scrap is increasing. These wastes and scraps include products rejected from manufacturing processes and obstacle computers. Owing to a short life cycle of electronic products and rapid growth of electronic industries, the number of domestic EOL computers goes beyond a million and its disposal causes an environmental problems. Therefore, this recycling is considered to play an important role from the viewpoint of environmental preservation as well as reusable resources. The process development for the recovery of valuable materials and minimization of waste from electronic scrap has been carried out. In the first year of three year project, physical separation such as shredding, crushing, and magnetic separation is established to reclaim valuable materials effectively. Then, hydro- and pyrometallurgical processes are employed to recover valuable metals from electronic scrap. First, metallic and nonmetallic portion are separated from PCBs by a newly designed shredder to prevent hazardous organic materials from further chemical treatment. The optimum conditions for each unit process were found in terms of separation ratio, energy consumption, recovery rate, etc. (author). 92 refs., 24 tabs., 39 figs.

  10. Contaminated nickel scrap processing

    Energy Technology Data Exchange (ETDEWEB)

    Compere, A.L.; Griffith, W.L.; Hayden, H.W.; Johnson, J.S. Jr.; Wilson, D.F.

    1994-12-01

    The DOE will soon choose between treating contaminated nickel scrap as a legacy waste and developing high-volume nickel decontamination processes. In addition to reducing the volume of legacy wastes, a decontamination process could make 200,000 tons of this strategic metal available for domestic use. Contaminants in DOE nickel scrap include {sup 234}Th, {sup 234}Pa, {sup 137}Cs, {sup 239}Pu (trace), {sup 60}Co, U, {sup 99}Tc, and {sup 237}Np (trace). This report reviews several industrial-scale processes -- electrorefining, electrowinning, vapormetallurgy, and leaching -- used for the purification of nickel. Conventional nickel electrolysis processes are particularly attractive because they use side-stream purification of process solutions to improve the purity of nickel metal. Additionally, nickel purification by electrolysis is effective in a variety of electrolyte systems, including sulfate, chloride, and nitrate. Conventional electrorefining processes typically use a mixed electrolyte which includes sulfate, chloride, and borate. The use of an electrorefining or electrowinning system for scrap nickel recovery could be combined effectively with a variety of processes, including cementation, solvent extraction, ion exchange, complex-formation, and surface sorption, developed for uranium and transuranic purification. Selected processes were reviewed and evaluated for use in nickel side-stream purification. 80 refs.

  11. Radioactive ground-water contamination from an enriched-uranium cold scrap recovery operation, Wood River Junction, Rhode Island

    International Nuclear Information System (INIS)

    Ryan, B.J.; Kipp, K.L. Jr.

    1984-01-01

    Liquid wastes from a uranium-bearing cold scrap recovery plant at an industrial site in Wood River Junction, Rhode Island were discharged to the environment through evaporation ponds from 1966 to 1980. Leakage from the polyethylene- and polyvinylchloride-lined ponds resulted in a plume of contaminated ground water that extends from the ponds northwestward to the Pawcatuck River through a highly permeable sand and gravel aquifer of glacial origin. Contaminants include: strontium 90, technetium 99, boron, nitrate and potassium. Water quality data from more than 100 observation wells indicate that the plume of contamination is approximately 700 meters long, 100 meters wide, and is confined to the upper 25 meters of saturated thickness where sediments consist of medium to coarse sand and gravel. No contamination has been detected in fine sands and silts underlying the coarser materials. Piezometric-head and water-quality data from wells screened at multiple depths on both sides of the river indicate that contaminants discharge both to the river and to a swampy area at the west edge of the river. Dilution precludes detection of contaminants once they have entered the river, which has an average flow of 5 cubic meters per second

  12. The new MAW scrap processing facility

    International Nuclear Information System (INIS)

    Kueppers, L.

    1994-01-01

    The shielded bunker for heat-generating waste attached to the MAW scrap processing cell will be modified and extended to comprise several MAW scrap processing cells of enhanced throughput capacity, and a new building to serve as an airlock and port for acceptance of large shipping casks (shipping cask airlock, TBS). The new facility is to process scrap from decommissioned nuclear installations, and in addition radwaste accrued at operating plants of utilities. This will allow efficient and steady use of the new MAW scrap processing facility. The planning activities for modification and extension are based on close coordination between KfK and the GNS mbH, in order to put structural dimensioning and capacity planning on a realistic basis in line with expected amounts of radwaste from operating nuclear installations of utilities. The paper indicates the currently available waste amount assessments covering solid radwaste (MAW) from the decommissioning of the WAK, MZFR, and KNK II, and existing waste amounts consisting of core internals of German nuclear power plant. The figures show that the MAW scrap processing facility will have to process an overall bulk of about 1100 Mg of solid waste over the next ten years to come. (orig./HP) [de

  13. Catalytic extraction processing of contaminated scrap metal

    International Nuclear Information System (INIS)

    Griffin, T.P.; Johnston, J.E.

    1994-01-01

    The contract was conceived to establish the commercial capability of Catalytic Extraction Processing (CEP) to treat contaminated scrap metal in the DOE inventory. In so doing, Molten Metal Technology, Inc. (MMT), pursued the following objectives: demonstration of the recycling of ferrous and non-ferrous metals--to establish that radioactively contaminated scrap metal can be converted to high-grade, ferrous and non-ferrous alloys which can be reused by DOE or reintroduced into commerce; immobilize radionuclides--that CEP will concentrate the radionuclides in a dense vitreous phase, minimize secondary waste generation and stabilize and reduce waste volume; destroy hazardous organics--that CEP will convert hazardous organics to valuable industrial gases, which can be used as feed gases for chemical synthesis or as an energy source; recovery volatile heavy metals--that CEP's off-gas treatment system will capture volatile heavy metals, such as mercury and lead; and establish that CEP is economical for processing contaminated scrap metal in the DOE inventory--that CEP is a more cost-effective and, complete treatment and recycling technology than competing technologies for processing contaminated scrap. The process and its performance are described

  14. Bioleaching of electronic scrap by mixed culture of moderately thermophilic microorganisms

    Science.gov (United States)

    Ivǎnuş, D.; ǎnuş, R. C., IV; Cǎlmuc, F.

    2010-06-01

    A process for the metal recovery from electronic scrap using bacterial leaching was investigated. A mixed culture of moderately thermophilic microorganisms was enriched from acid mine drainages (AMDs) samples collected from several sulphide mines in Romania, and the bioleaching of electronic scrap was conducted both in shake flask and bioreactor. The results show that in the shake flask, the mixture can tolerate 50 g/L scrap after being acclimated to gradually increased concentrations of scrap. The copper extraction increases obviously in bioleaching of scrap with moderately thermophilic microorganisms supplemented with 0.4 g/L yeast extract at 180 r/min, 74% copper can be extracted in the pulp of 50 g/L scrap after 20 d. Compared with copper extractions of mesophilic culture, unacclimated culture and acclimated culture without addition of yeast extract, that of accliniated culture with addition of yeast extract is increased by 53%, 44% and 16%, respectively. In a completely stirred tank reactor, the mass fraction of copper and total iron extraction reach up to 81% and 56%, respectively. The results also indicate that it is necessary to add a large amount of acid to the pulp to extract copper from electronic scrap effectively.

  15. Palladium and gold removal and recovery from precious metal solutions and electronic scrap leachates by Desulfovibrio desulfuricans.

    Science.gov (United States)

    Creamer, Neil J; Baxter-Plant, Victoria S; Henderson, John; Potter, M; Macaskie, Lynne E

    2006-09-01

    Biomass of Desulfovibrio desulfuricans was used to recover Au(III) as Au(0) from test solutions and from waste electronic scrap leachate. Au(0) was precipitated extracellularly by a different mechanism from the biodeposition of Pd(0). The presence of Cu(2+) ( approximately 2000 mg/l) in the leachate inhibited the hydrogenase-mediated removal of Pd(II) but pre-palladisation of the cells in the absence of added Cu(2+) facilitated removal of Pd(II) from the leachate and more than 95% of the Pd(II) was removed autocatalytically from a test solution supplemented with Cu(II) and Pd(II). Metal recovery was demonstrated in a gas-lift electrobioreactor with electrochemically generated hydrogen, followed by precipitation of recovered metal under gravity. A 3-stage bioseparation process for the recovery of Au(III), Pd(II) and Cu(II) is proposed.

  16. The Study for Recycling NORM - Contaminated Steel Scraps from Steel Industry

    International Nuclear Information System (INIS)

    Tsai, K. F.; Lee, Y. S.; Chao, H. E.

    2003-01-01

    Since 1994, most of the major steel industries in Taiwan have installed portal monitor to detect the abnormal radiation in metal scrap feed. As a result, the discovery of NORM (Naturally Occurring Radioactive Material) has increased in recent years. In order to save the natural resources and promote radiation protection, an experimental melting process for the NORM contaminated steel scraps was carried out by the Institute of Nuclear Energy Research (INER) Taiwan, ROC. The experimental melting process has a pretreatment step that includes a series of cutting and removal of scales, sludge, as well as combustible and volatile materials on/in the steel scraps. After pretreatment the surface of the steel scraps are relatively clean. Then the scraps are melted by a pilot-type induction furnace. This experiment finally produced seven ingots with a total weight of 2,849 kg and 96.8% recovery. All of the surface dose rates are of the background values. The activity concentrations of these ingots are also below the regulatory criteria. Thus, these NORM-bearing steel scraps are ready for recycling. This study has been granted by the regulatory authority

  17. Wastes from plutonium conversion and scrap recovery operations

    Energy Technology Data Exchange (ETDEWEB)

    Christensen, D.C.; Bowersox, D.F.; McKerley, B.J.; Nance, R.L.

    1988-03-01

    This report deals with the handling of defense-related wastes associated with plutonium processing. It first defines the different waste categories along with the techniques used to assess waste content. It then discusses the various treatment approaches used in recovering plutonium from scrap. Next, it addresses the various waste management approaches necessary to handle all wastes. Finally, there is a discussion of some future areas for processing with emphasis on waste reduction. 91 refs., 25 figs., 4 tabs.

  18. Wastes from plutonium conversion and scrap recovery operations

    International Nuclear Information System (INIS)

    Christensen, D.C.; Bowersox, D.F.; McKerley, B.J.; Nance, R.L.

    1988-03-01

    This report deals with the handling of defense-related wastes associated with plutonium processing. It first defines the different waste categories along with the techniques used to assess waste content. It then discusses the various treatment approaches used in recovering plutonium from scrap. Next, it addresses the various waste management approaches necessary to handle all wastes. Finally, there is a discussion of some future areas for processing with emphasis on waste reduction. 91 refs., 25 figs., 4 tabs

  19. Developments in radioactive scrap monitoring

    International Nuclear Information System (INIS)

    Bellian, J.G.

    1997-01-01

    Over the past ten years there have been major developments in radiation monitoring systems used for detecting shielded radioactive sources in scrap metal. The extent of the problem and industry's awareness of the problem have both grown significantly during that time. The multimillion dollar expenses associated with decontamination after a source passes into the melt and the potential health hazard to employees and the public have added further impetus to the development of monitoring systems. Early attempts at scrap monitoring could detect some radiation, but testing with real life situations showed them to be virtually incapable of detecting shielded sources of radioactivity in incoming vehicles. More sophisticated detector technology and the development of advanced software made useful by more powerful microprocessors led to successive generations of monitoring systems with order-of-magnitude improvement in detection capability. The next generation includes larger detectors and more complex algorithms offering further improvement in truck and rail car monitoring. Complete solutions require monitoring at additional locations within the site, such as the charge bucket and conveyor lines, and at the scrap processor's site

  20. A recovery of gold from electronic scrap by mechanical separation, acid leaching and electrowinning

    Energy Technology Data Exchange (ETDEWEB)

    Rhee, K.I.; Lee, J.C.; Lee, C.K.; Joo, K.H.; Yoon, J.K.; Kang, H.R.; Kim, Y.S.; Sohn, H.J.

    1995-12-31

    A series of processes to recover the gold from electronic scrap which contains initially about 200--600 ppm Au have been developed. First, mechanical beneficiation including shredding, crushing and screening was employed. Results showed that 99 percent of gold component leaves in the fraction of under 1 mm of crushed scrap and its concentration was enriched to about 800 ppm without incineration. The scrap was leached in 50% aqua regia solution and gold was dissolved completely at 60 C within 2 hours. Other valuable metals such as silver, copper, nickel and iron were also dissolved. This resulting solution was boiled to remove nitrous compounds in the leachate. Finally, a newly designed electrolyzer was tested to recover the gold metal. More than 99% of gold and silver were recovered within an hour in electrowinning process.

  1. Release of Radioactive Scrap Metal/Scrap Metal (RSM/SM) at Nevada Test Site (NTS)

    International Nuclear Information System (INIS)

    1993-01-01

    Reynolds Electrical and Engineering Company, Inc. (REECo) is the prime contractor to the US Department of Energy (DOE) in providing service and support for NTS operations. Mercury Base Camp is the main control point for the many forward areas at NTS, which covers 1,350 square miles. The forward areas are where above-ground and underground nuclear tests have been performed over the last 41 years. No metal (or other material) is returned to Mercury without first being tested for radioactivity. No radioactive metals are allowed to reenter Mercury from the forward areas, other than testing equipment. RAMATROL is the monitor check point. They check material in various ways, including swipe tests, and have a large assortment of equipment for testing. Scrap metal is also checked to address Resource Conservation and Recovery Act concerns. After addressing these issues, the scrap metals are categorized. Federal Property Management Regulations (FPMR) are followed by REECo. The nonradioactive scrap material is sold through the GSA on a scheduled basis. Radioactive scrap metal are presently held in forward areas where they were used. REECo has gained approval of their Nevada Test Site Defense Waste Acceptance Criteria, Certification, and Transfer Requirements, NVO-325 application, which will allow disposal on site, when RSM is declared a waste. The guideline that REECo uses for release limits is DOE Order 5480.11, Radiation Protection for Occupational Works, Attachment 2, Surface Radioactivity Guides, of this order, give release limits for radioactive materials. However, the removal of radioactive materials from NTS require approval by DOE Nevada Operations Office (DOE/NV) on a case-by-case basis. Requirements to consider before removal are found in DOE Order 5820.2A, Radioactive Waste Management

  2. Optimization of fuel recovery through the stepwise co-pyrolysis of palm shell and scrap tire

    International Nuclear Information System (INIS)

    Abnisa, Faisal; Wan Daud, Wan Mohd Ashri

    2015-01-01

    Highlights: • The co-pyrolysis of palm shell and scrap tire was studied. • The effect of stepwise co-pyrolysis temperature was investigated. • Co-pyrolysis successfully improved the quantity and quality of product yields. • Stepwise co-pyrolysis slightly increased oil and gas, and decreased char. • The co-pyrolysis of 50% biomass and 50% scrap tire is recommended. - Abstract: This study optimized the use of biomass waste to generate fuel through co-pyrolysis. In this paper, the effects of stepwise co-pyrolysis temperature and different ratios between palm shells and scrap tires in feedstock were studied to observe any improvements in the quantity and quality of the liquid yield and its byproduct. The ratio of palm shells and scrap tires varied at 100:0, 75:25, 50:50, 25:75, and 0:100. The experiment was conducted in a fixed-bed reactor. The study was divided into two scenarios. The first scenario was performed at the optimum temperature of 500 °C with a reaction time of 60 min. In the second scenario, the temperature was set at 500 °C for 60 min before the temperature was increased to 800 °C with a high heating rate. After the temperature reached 800 °C, the condition was maintained for approximately 45 min. Results showed that an increase in the liquid and gas yields was achieved when the temperature increased after optimum conditions. Increased yield was also obtained when the proportion of scrap tire was increased in the feedstock. Several other important findings are discussed in this paper, including the phases of pyrolysis oil, features of the liquid product, and characteristics of the byproducts. All products from both scenarios were analyzed by various methods to understand their fuel characteristics

  3. Issues in recycling galvanized scrap

    Energy Technology Data Exchange (ETDEWEB)

    Koros, P.J. [LTV Steel Co., Inc., Cleveland, OH (United States); Hellickson, D.A. [General Motors Corp., Detroit, MI (United States); Dudek, F.J. [Argonne National Lab., IL (United States)

    1995-02-10

    The quality of the steel used for most galvanizing (and tinplate) applications makes scrap derived from their production and use a premier solid charge material for steelmaking. In 1989 the AISI created a Task Force to define the issues and to recommend technologically and economically sound approaches to assure continued, unhindered recyclability of the growing volume of galvanized scrap. The AISI program addressed the treatment of full-sized industrial bales of scrap. The current, on-going MRI (US)--Argonne National Laboratory program is focused on ``loose`` scrap from industrial and post-consumer sources. Results from these programs, issues of scrap management from source to steel melting, the choices for handling zinc in iron and steelmaking and the benefits/costs for removal of zinc (and lead) from scrap prior to melting in BOF and foundry operations are reviewed in this paper.

  4. Scrap automotive electronics: A mini-review of current management practices.

    Science.gov (United States)

    Cucchiella, Federica; D'Adamo, Idiano; Rosa, Paolo; Terzi, Sergio

    2016-01-01

    End-of-life vehicles, together with waste from electric and electronic equipment, are known as an important source of secondary raw materials. For many years, their recovery has allowed the restoring of great amounts of metals for new cars production. This article provides a comprehensive mini-review on the end-of-life vehicles recycling topic between 2000 and 2014, with a particular focus on automotive electronics recycling. In fact, in the last years, experts focused their attention on a better exploitation of automotive shredder residue fraction, but not sufficiently on eventual electronic scraps embedded in it. Hence, studies assessing the value embedded in these scraps are rarely available in literature, causing an important gap in both recycling policies and research. The fact that, at present, the management of electronic control units (the most valuable component among automotive electronic equipment) is, as yet, off the radar in both end-of-life vehicles and waste from electric and electronic equipment Directives demonstrates the theory. Of course, their recycling would not contribute in a relevant way to reach the weighted-based recycling and recovery targets characterising current regulations, but would be very important under a critical raw materials recovery view. Results coming from the literature analysis confirm these assumptions. © The Author(s) 2015.

  5. Characterization of naturally occurring radioactive materials and Cobald-60 contaminated ferrous scraps from steel industries

    International Nuclear Information System (INIS)

    Chao, H.E.; Chiu, H.S.; Hunga, J.Y.; His, H.W.; Chen, Y.B.

    2002-01-01

    Since the occurrence of radioactively contaminated rebar incident in 1992, steel industries in Taiwan were encouraged by Atomic Energy Council (AEC) to install portal monitor to detect the abnormal radiation in shipments of metal scrap feed. From 1994 through 1999, there were 53 discoveries of radioactivity in ferrous scraps by steel companies. These include 15 orphan radioactive sources, 16 cobalt-60 contaminated rebars, 20 Naturally Occurring Radioactive Material (NORM) contaminated scraps, and two unknowns. Most NORM-contaminated scraps were from abroad. The NORM and cobalt-60 contaminated scraps were taken from the steel mills and analyzed in laboratory. The analytical results of scales and sludge sampled from NORM-contaminated scraps combining with the circumstantial evidences indicate that five possible industrial processes may be involved. They are oil production and treatment, heavy mineral sand benefication and rare earth processing, copper mining and processing, recovery of ammonium chloride by lime adsorption in Ammonium-soda process, and tailing of uranium enrichment process. The cobalt-60 activity and trace elements concentrations of contaminated rebars confirm that all of them were produced domestically in the period from Oct. 1982 to Jan. 1983, when the cobalt-60 sources were lost and entered the electric arc furnace to produce the contaminated rebars. (author)

  6. Characterization of Neptunium Oxide Generated Using the HB-Line Phase II Flowsheet

    Energy Technology Data Exchange (ETDEWEB)

    Duffey, J

    2003-08-29

    Approximately 98 grams of neptunium(IV) oxide (NpO{sub 2}) were produced at the Savannah River Technology Center (SRTC) for use in gas generation tests to support the neptunium stabilization program at the Savannah River Site (SRS). The NpO{sub 2} was produced according to the anticipated HB-Line flowsheet consisting of anion exchange, oxalate precipitation, filtration, and calcination. Characterization of the NpO{sub 2} product to be used in gas generation tests included bulk and tap density measurements, X-ray diffraction, particle size distribution, specific surface area measurements, and moisture analysis.

  7. The Spanish system for the radiological surveillance and control of scrap and the products resulting from its processing

    International Nuclear Information System (INIS)

    Gil, E.

    2001-01-01

    Despite the fact that the use of radiation technologies has always been subjected to strict controls in most countries, the presence of radioactive materials in scrap has been detected relatively often in recent years. This has led to the implementation of a series of international initiatives aimed at detecting and preventing illicit international trafficking with radioactive material, intentional or otherwise. The Spanish iron and steel industry is one of the most important industrial sectors in the country, and depends to a large extent on the importing of a significant proportion of the scrap its uses as raw material. Experience has shown that that countries that import large quantities of scrap should complement the aforementioned international initiatives with others of national scope, in order to reduce the risks arising from the presence of radioactive material in scrap. In this context, the Spanish radiological protection authorities, along with the business associations involved in the metal recovery and smelting industry, have established a national system for the radiological surveillance and control of scrap and of the products resulting from its processing. The system consists of a set of legal bases, the installation of specific radiological surveillance equipment and the enhancement of other general purpose equipment that existed prior to these initiatives, the development of radiological training and information plans for the professionals involved in the metal recovery and smelting sectors and improvement to the national radiological emergency response system. (author)

  8. ORO scrap metal decontamination program

    International Nuclear Information System (INIS)

    Jugan, M.

    1987-01-01

    The Oak Ridge Operations Office (ORO) of the US Department of Energy (DOE) has approximately 80,000 tons of contaminated scrap metal at the Oak Ridge Gaseous Diffusion Plant in Oak Ridge, Tennessee; Paducah Gaseous Diffusion Plant in Paducah, Kentucky; Portsmouth Gaseous Diffusion Plant in Piketon, Ohio; and the Feed Materials Production Center in Fernald, Ohio. After unsuccessful in-house attempts to eliminate/recycle the contaminated metal, DOE is allowing private enterprise the opportunity to participate in this program. DOE is making this opportunity available under a two-phase approach, which is being supported by two separate and corresponding Request for Proposals. Phase I, which is nearing completion, is a demonstration phase to establish a group of companies that the DOE will consider qualified to eliminate the scrap at one or more sites. In Phase I, the companies decontaminated 25-50 tons of scrap to demonstrate capabilities to DOE and to gain the knowledge required to plan/bid on elimination of the scrap at one or more sites. Phase II will request proposals for elimination of the total scrap at one or more of the above noted sites. Multiple awards for Phase II are also anticipated. Companies participating in Phase II will be required to take title to the contaminated scrap and decontaminate/process the scrap for beneficial reuse. Radioactive wastes and metal that cannot be successfully decontaminated/processed will be returned to DOE

  9. Enhancing energy recovery in the steel industry: Matching continuous charge with off-gas variability smoothing

    International Nuclear Information System (INIS)

    Dal Magro, Fabio; Meneghetti, Antonella; Nardin, Gioacchino; Savino, Stefano

    2015-01-01

    Highlights: • A system based on phase change material is inserted into the off-gas-line of a continuous charge electric arc furnace. • The off-gas temperature profile after scrap preheating is smoothed. • A heat transfer fluid through phase change material containers allows to control overheating issues. • The smoothed off-gas profiles enable efficient downstream power generation. • The recovery system investment cost is decreased due to lower sizes of components. - Abstract: In order to allow an efficient energy recovery from off-gas in the steel industry, the high variability of heat flow should be managed. A temperature smoothing device based on phase change materials at high temperatures is inserted into the off-gas line of a continuous charge electric arc furnace process with scrap preheating. To address overheating issues, a heat transfer fluid flowing through containers is introduced and selected by developing an analytical model. The performance of the smoothing system is analyzed by thermo-fluid dynamic simulations. The reduced maximum temperature of off-gas allows to reduce the size and investment cost of the downstream energy recovery system, while the increased minimum temperature enhances the steam turbine load factor, thus increasing its utilization. Benefits on environmental issues due to dioxins generation are also gained

  10. Characteristics of Indium Tin Oxide (ITO Nanoparticles Recovered by Lift-off Method from TFT-LCD Panel Scraps

    Directory of Open Access Journals (Sweden)

    Dongchul Choi

    2014-11-01

    Full Text Available In this study, indium-tin-oxide (ITO nanoparticles were simply recovered from the thin film transistor-liquid crystal display (TFT-LCD panel scraps by means of lift-off method. This can be done by dissolving color filter (CF layer which is located between ITO layer and glass substrate. In this way the ITO layer was easily lifted off the glass substrate of the panel scrap without panel crushing. Over 90% of the ITO on the TFT-LCD panel was recovered by using this method. After separating, the ITO was obtained as particle form and their characteristics were investigated. The recovered product appeared as aggregates of particles less than 100 nm in size. The weight ratio of In/Sn is very close to 91/9. XRD analysis showed that the ITO nanoparticles have well crystallized structures with (222 preferred orientation even after recovery. The method described in this paper could be applied to the industrial recovery business for large size LCD scraps from TV easily without crushing the glass substrate.

  11. 7 CFR 29.2277 - Leaf scrap.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.2277 Section 29.2277 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... scrap. A byproduct of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and consists...

  12. 32 CFR 644.522 - Clearance of military scrap.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 4 2010-07-01 2010-07-01 true Clearance of military scrap. 644.522 Section 644... Excess Land and Improvements § 644.522 Clearance of military scrap. Military scrap can contain or be... destruction, by using command, of all military scrap and scrap metal from lands suitable for cultivation or...

  13. 7 CFR 29.3526 - Leaf scrap.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.3526 Section 29.3526 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Type 95) § 29.3526 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results from handling...

  14. 7 CFR 29.3034 - Leaf scrap.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.3034 Section 29.3034 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... Leaf scrap. A by-product of unstemmed tobacco. Leaf scrap results from handling unstemmed tobacco and...

  15. 7 CFR 29.6022 - Leaf scrap.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.6022 Section 29.6022 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Definitions § 29.6022 Leaf scrap. A byproduct of unstemmed tobacco Leaf scrap results...

  16. HB-LINE ANION EXCHANGE PURIFICATION OF AFS-2 PLUTONIUM FOR MOX

    Energy Technology Data Exchange (ETDEWEB)

    Kyser, E.; King, W.

    2012-04-25

    Non-radioactive cerium (Ce) and radioactive plutonium (Pu) anion exchange column experiments using scaled HB-Line designs were performed to investigate the feasibility of using either gadolinium nitrate (Gd) or boric acid (B as H{sub 3}BO{sub 3}) as a neutron poison in the H-Canyon dissolution process. Expected typical concentrations of probable impurities were tested and the removal of these impurities by a decontamination wash was measured. Impurity concentrations are compared to two specifications - designated as Column A or Column B (most restrictive) - proposed for plutonium oxide (PuO{sub 2}) product shipped to the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). Use of Gd as a neutron poison requires a larger volume of wash for the proposed Column A specification. Since boron (B) has a higher proposed specification and is more easily removed by washing, it appears to be the better candidate for use in the H-Canyon dissolution process. Some difficulty was observed in achieving the Column A specification due to the limited effectiveness that the wash step has in removing the residual B after {approx}4 BV's wash. However a combination of the experimental 10 BV's wash results and a calculated DF from the oxalate precipitation process yields an overall DF sufficient to meet the Column A specification. For those impurities (other than B) not removed by 10 BV's of wash, the impurity is either not expected to be present in the feedstock or process, or recommendations have been provided for improvement in the analytical detection/method or validation of calculated results. In summary, boron is recommended as the appropriate neutron poison for H-Canyon dissolution and impurities are expected to meet the Column A specification limits for oxide production in HB-Line.

  17. HB-LINE ANION EXCHANGE PURIFICATION OF AFS-2 PLUTONIUM FOR MOX

    Energy Technology Data Exchange (ETDEWEB)

    Kyser, E. A.; King, W. D.

    2012-07-31

    Non-radioactive cerium (Ce) and radioactive plutonium (Pu) anion exchange column experiments using scaled HB-Line designs were performed to investigate the feasibility of using either gadolinium nitrate (Gd) or boric acid (B as H{sub 3}BO{sub 3}) as a neutron poison in the H-Canyon dissolution process. Expected typical concentrations of probable impurities were tested and the removal of these impurities by a decontamination wash was measured. Impurity concentrations are compared to two specifications - designated as Column A or Column B (most restrictive) - proposed for plutonium oxide (PuO{sub 2}) product shipped to the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). Use of Gd as a neutron poison requires a larger volume of wash for the proposed Column A specification. Since boron (B) has a higher proposed specification and is more easily removed by washing, it appears to be the better candidate for use in the H-Canyon dissolution process. Some difficulty was observed in achieving the Column A specification due to the limited effectiveness that the wash step has in removing the residual B after ~4 BV's wash. However a combination of the experimental 10 BV's wash results and a calculated DF from the oxalate precipitation process yields an overall DF sufficient to meet the Column A specification. For those impurities (other than B) not removed by 10 BV's of wash, the impurity is either not expected to be present in the feedstock or process, or recommendations have been provided for improvement in the analytical detection/method or validation of calculated results. In summary, boron is recommended as the appropriate neutron poison for H-Canyon dissolution and impurities are expected to meet the Column A specification limits for oxide production in HB-Line.

  18. Gas Generation during Sodium Permanganate Addition to HB-Line Phase II Filtrate Tank

    International Nuclear Information System (INIS)

    Hill, B.C.

    2002-01-01

    HB-Line Phase II process requires the addition of sodium permanganate followed by a sodium nitrite addition to prevent the precipitation of plutonium solids in a non-geometrically safe vessel. Previous experimental work has shown this method effective. Current concerns are related to the gas generated by the reaction. Potential difficulties include tank over-pressurization and tank overflow due to foaming or eructation. It is also necessary to verify that the quantity of permanganate specified by the facility is sufficient to reach the desired endpoint in a single addition

  19. Leachability of heavy metals from scrap dirt sampled at two scrap iron and metal recycling facilities

    DEFF Research Database (Denmark)

    Jensen, Dorthe Lærke; Holm, Peter Engelund; Christensen, Thomas Højlund

    2000-01-01

    Column and batch leaching experiments were performed to quantify leaching of heavy metals (Pb, Cu, Cd and Zn) from scrap dirt representing different activities at two iron scrap and metal recycling facilities. The scrap dirt is often found directly upon the bare unprotected soil at recycling...... battery salvage locations was different, showing lower pH and signi®cant leaching of lead (up to 8000 mg Pb l±1), cadmium (up to 40 mg Cd l±1), and zinc (up to 2000 mg Zn l±1). The column and batch leaching experiments gave comparable results at the order of magnitude level, and both approaches are......, at that level, useful for evaluation of leaching potentials from scrap dirt. The experiments showed that scrap dirt at recycling facilities constitutes only a modest leaching problem, but a long-term soil pollution problem from a land-use perspective. Leaching experiments with compost solution indicated...

  20. Considerations in recycling contaminated scrap metal and rubble

    International Nuclear Information System (INIS)

    Kluk, A.F.; Hocking, E.K.

    1992-01-01

    Management options for the Department of Energy's increasing amounts of contaminated scrap metal and rubble include reuse as is, disposal, and recycling. Recycling, with its promise of resource recovery, virgin materials conservation, and land disposal minimization, emerges as a preferred management technique. Implementing a cost effective recycling program requires resolution of several issues including: establishing release limits for contaminants, controlling use of recycled materials creating effective public communication programs; developing economical, reliable assay technologies; managing secondary waste streams, expanding availability of unrestricted markets; and solving conflicting legal considerations

  1. Slovenian System for Protecting Against Radioactive Material in Scrap Metal Shipments

    Energy Technology Data Exchange (ETDEWEB)

    Stritar, A.; Cesarek, J.; Vokal Nemec, B., E-mail: andrej.stritar@gov.si [Slovenian Nuclear Safety Administration, Ljubljana (Slovenia)

    2011-07-15

    The Slovenian experience shows that the majority of detected orphan sources are associated with imports of scrap metal to Slovenia and transits of that material through Slovenia. Such orphan sources originate from past industrial activities and weak regulatory control in the countries of origin. In order to minimise the number of sources outside regulatory control several regulatory and law enforcement measures have been implemented. To prevent illicit trafficking across the border the 'First line of defence' - customs and police - are equipped with radiation detection devices. Since 2002, the Slovenian Nuclear Safety Administration (SNSA) has provided a 24-hour on-duty officer, who gives advice in case of the discovery of an orphan source. The majority of scrap metal collectors and re-cyclers are equipped with portal monitors and/or hand-held radiation detection equipment. Generally, good cooperation has been established between different organizations within Slovenia, with neighbouring countries and with some international organizations. To regulate the scrap metal activities, a new Decree on checking the radioactivity of shipments of metal scrap has been in force since 1 January 2008. This decree requires that every importer has to present a certificate of radiation measurement before any shipment of scrap metal is brought into Slovenia. Such measurements can be performed only by certified organizations. These organizations can obtain certification from the SNSA providing that they have the prescribed measuring devices, adequate training and procedures, and that their capabilities have been checked by a technical support organization. The experience after one year of application of the decree is positive. Awareness, including the adequacy of response, has increased. The paper discusses the general scheme for protection against illicit radioactive material in scrap metal shipments and the Slovenian experience in the last decade. (author)

  2. 7 CFR 29.1169 - Scrap (S Group).

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Scrap (S Group). 29.1169 Section 29.1169 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Grades § 29.1169 Scrap (S Group). A byproduct of stemmed and unstemmed tobacco. Scrap...

  3. 7 CFR 29.2441 - Scrap (S Group).

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Scrap (S Group). 29.2441 Section 29.2441 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... INSPECTION Standards Grades § 29.2441 Scrap (S Group). A byproduct of unstemmed and stemmed tobacco. Scrap...

  4. Import of metal scrap - risks associated with radioactivity

    International Nuclear Information System (INIS)

    Elert, M.

    1992-11-01

    There is a growing concern in Sweden for the possibility that imported metal scrap is radioactive. The recent political and economical changes in eastern Europe and the increased cooperation with the CEC has affected Swedens import. In the last years, the import of metal scrap from the former USSR has increased considerably. In view of recent incidents, when radioactive materials have been found, the Swedish Radiation Protection Institute has detected a need for identifying the potential risk sources and evaluating the magnitude of the risk associated with the import of metal scrap. The purpose of this report is to provide some background material concerning import statistics, use of metal scrap in Sweden and to identify potential sources of radioactive metal scrap. In addition, the radionuclides of most concern has been identified and the possibility of detecting them in metal scrap shipments is analyzed

  5. Lead scrap use and trade patterns in the United States, 1995-2012

    Science.gov (United States)

    Wilburn, David R.

    2015-09-22

    Since 1995, domestic production of lead has increasingly shifted from primary mining and smelting to the recovery of lead-bearing scrap by the secondary lead industry, which accounted for 91 percent of U.S. lead production in 2012. Increasingly stringent environmental regulations for lead emissions in the United States have contributed to the closure of primary lead refineries and the consolidation of the secondary lead industry. Domestic production of lead from the primary and secondary sectors in 2012 is essentially unchanged from the amount produced in 1995. The U.S. secondary industry produced an estimated 145,000 metric tons more refined lead in 2012 than it did in 1995, primarily by recovering lead from battery scrap, allowing the U.S. to maintain production at a level sufficient to supply much of the domestic demand for lead.

  6. Fernald scrap metal recycling and beneficial reuse

    International Nuclear Information System (INIS)

    Motl, G.P.; Burns, D.D.

    1993-10-01

    The Fernald site, formerly the Feed Materials Production Facility, produced uranium metal products to meet defense production requirements for the Department of Energy from 1953 to 1989. In this report is is described how the Fernald scrap metal project has demonstrated that contractor capabilities can be used successfully to recycle large quantities of Department of Energy scrap metal. The project has proven that the open-quotes beneficial reuseclose quotes concept makes excellent economic sense when a market for recycled products can be identified. Topics covered in this report include the scrap metal pile history, the procurement strategy, scrap metal processing, and a discussion of lessons learned

  7. Control and Management of Radioactive Material Inadvertently Incorporated into Scrap Metal. Proceedings of an International Conference

    International Nuclear Information System (INIS)

    2011-01-01

    Radioactive substances can become associated with scrap metal in various ways and if not discovered they can be incorporated into steel and non-ferrous metals through the melting process. This can cause health hazards as well as environmental concerns and there can be serious commercial implications. Numerous incidents have occurred in recent years involving the discovery of radioactive substances in scrap metal and, in some cases, in metal from the melting process. These incidents have proved to be very costly in relation to the recovery and cleanup operations required but also in terms of the potential loss of confidence of the industry in scrap metal as a resource. This has led the scrap metal industry to seek ways of managing the problem. In most countries, shipments of scrap metal are monitored but at different points in the distribution chain and to different extents and efficiencies. As yet, only limited efforts towards unifying and harmonizing monitoring strategies and methods in the context of scrap metal have been made at the international level. The Conference was organized into five sessions: the global perspective, national policies and strategies, compliance with radiological criteria, management of incidents with contaminated scrap metal, and improving confidence and protecting the interests of stakeholders. The aim of the first session was to present the views and perspectives of the different organizations concerned with radioactive material in scrap metal, scrap metal recycling, steel making, radiation source security and safety and international trade and economics. The second session covered some of the national policies and strategies being used to address the control of radioactive material that has been inadvertently incorporated into scrap metal were presented. In addition to the oral presentations, contributions describing the situation in many countries of the world in the form of posters were displayed. The many posters reporting national

  8. Control and Management of Radioactive Material Inadvertently Incorporated into Scrap Metal. Proceedings of an International Conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-15

    Radioactive substances can become associated with scrap metal in various ways and if not discovered they can be incorporated into steel and non-ferrous metals through the melting process. This can cause health hazards as well as environmental concerns and there can be serious commercial implications. Numerous incidents have occurred in recent years involving the discovery of radioactive substances in scrap metal and, in some cases, in metal from the melting process. These incidents have proved to be very costly in relation to the recovery and cleanup operations required but also in terms of the potential loss of confidence of the industry in scrap metal as a resource. This has led the scrap metal industry to seek ways of managing the problem. In most countries, shipments of scrap metal are monitored but at different points in the distribution chain and to different extents and efficiencies. As yet, only limited efforts towards unifying and harmonizing monitoring strategies and methods in the context of scrap metal have been made at the international level. The Conference was organized into five sessions: the global perspective, national policies and strategies, compliance with radiological criteria, management of incidents with contaminated scrap metal, and improving confidence and protecting the interests of stakeholders. The aim of the first session was to present the views and perspectives of the different organizations concerned with radioactive material in scrap metal, scrap metal recycling, steel making, radiation source security and safety and international trade and economics. The second session covered some of the national policies and strategies being used to address the control of radioactive material that has been inadvertently incorporated into scrap metal were presented. In addition to the oral presentations, contributions describing the situation in many countries of the world in the form of posters were displayed. The many posters reporting national

  9. 7 CFR 29.2529 - Leaf scrap.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 2 2010-01-01 2010-01-01 false Leaf scrap. 29.2529 Section 29.2529 Agriculture Regulations of the Department of Agriculture AGRICULTURAL MARKETING SERVICE (Standards, Inspections, Marketing... tobacco. Leaf scrap results from handling unstemmed tobacco and consists of loose and tangled whole or...

  10. Activities and Issues in Monitoring Scrap Metal Against Radioactive Sources

    Energy Technology Data Exchange (ETDEWEB)

    Chen, S.Y., E-mail: sychen@anl.gov [Argonne National Laboratory, Argonne, IL (United States)

    2011-07-15

    Over the past few decades, the global scrap metal industry has grown increasingly vigilant regarding radioactive contamination. Accidental melts of radioactive sources in some smelting facilities, in particular, have caused considerable damage and required recovery efforts costing tens of millions of dollars. In response, the industry has developed and deployed countermeasures. Increasingly expensive and sophisticated radiation monitoring devices have been implemented at key scrap entry points - ports and scrapyards. Recognition of the importance of such endeavors has led to a series of activities aimed at establishing organized and coordinated efforts among the interested parties. Recent concerns over the potential use of radioactive sources for radiological devices in terrorist acts have substantially heightened the need for national and international authorities to further control, intercept, and secure the sources that have escaped the regulatory domain. Enhanced collaboration by the government and industry could substantially improve the effectiveness of efforts at control; the 'Spanish Protocol' as developed by the Spanish metal industry and government regulators is a good example of such collaboration. (author)

  11. The significance of disulfide bonding in biological activity of HB-EGF, a mutagenesis approach

    International Nuclear Information System (INIS)

    Hoskins, J.T.; Zhou, Z.; Harding, P.A.

    2008-01-01

    A site-directed mutagenesis approach was taken to disrupt each of 3 disulfide bonds within human HB-EGF by substituting serine for both cysteine residues that contribute to disulfide bonding. Each HB-EGF disulfide analogue (HB-EGF-Cys/Ser 108/121 , HB-EGF-Cys/Ser 116/132 , and HB-EGF-Cys/Ser 134/143 ) was cloned under the regulation of the mouse metallothionein (MT) promoter and stably expressed in mouse fibroblasts. HB-EGF immunoreactive proteins with M r of 6.5, 21 and 24 kDa were observed from lysates of HB-EGF and each HB-EGF disulfide analogue. HB-EGF immunohistochemical analyses of each HB-EGF stable cell line demonstrated ubiquitous protein expression except HB-EGF-Cys/Ser 108/121 and HB-EGF-Cys/Ser 116/132 stable cell lines which exhibited accumulated expression immediately outside the nucleus. rHB-EGF, HB-EGF, and HB-EGF 134/143 proteins competed with 125 I-EGF in an A431 competitive binding assay, whereas HB-EGF-Cys/Ser 108/121 and HB-EGF-Cys/Ser 116/132 failed to compete. Each HB-EGF disulfide analogue lacked the ability to stimulate tyrosine phosphorylation of the 170 kDa EGFR. These results suggest that HB-EGF-Cys/Ser 134/143 antagonizes EGFRs

  12. Radiation survey of aircraft and heavy machinery scrap

    International Nuclear Information System (INIS)

    Idriss, Hajo; Salih, Isam; Gumaa, Elsadig; Yassin, Abbas; Yousif, E.H.; Abdel Hamid, Saad Eldeen M.; Sam, A.K.

    2012-01-01

    This study was conducted primarily to survey aircraft and heavy machinery at 30 locations within Khartoum State using handheld radiation survey meters to detect and identify any radiation sources that might be present and to estimate radiation dose levels. The survey has resulted in detection of 16 sealed sources of 90 Sr and one of 226 Ra in aircraft scrap. Of course, 90 Sr sources are used in military aircraft as temperature sensors while 226 Ra is used for indicating fuel levels. These sources were found intact without spreading radioactivity contamination; however, none was detected in heavy machine scrap. The levels of radiation dose measured at 0.1 m from the source fall within the range of 25.1–40.2 μSv/h with an average value of 33.52±4.06 μSv/h. These orphan sources have been separated from the scrap, tested for possible leakage, conditioned and stored in waste management facility. The result of this study has revealed without doubt that the scrap constitute a serious source of public exposure and highlights the importance of legislation making radiation monitoring of scrap in the country mandatory before it is sold to metal industry for reprocessing. - Highlights: ► Sealed radioactive sources ( 90 Sr and 226 Ra) were detected in aircraft scrap. ► No source was detected in heavy machine scrap. ► Radiation dose measured at 0.1 m from the source can be used to estimate exposure to public. ► Monitoring of scrap was found to be useful for protection (from orphan sources).

  13. Feasibility of re-melting NORM-contaminated scrap metal

    Energy Technology Data Exchange (ETDEWEB)

    Winters, S. J.; Smith, K. P.

    1999-10-26

    Naturally occurring radioactive materials (NORM) sometimes accumulate inside pieces of equipment associated with oil and gas production and processing activities. Typically, the NORM accumulates when radium that is present in solution in produced water precipitates out in scale and sludge deposits. Scrap equipment containing residual quantities of these NORM-bearing scales and sludges can present a waste management problem if the radium concentrations exceed regulatory limits or activate the alarms on radiation screening devices installed at most scrap metal recycling facilities. Although NORM-contaminated scrap metal currently is not disposed of by re-melting, this form of recycling could present a viable disposition option for this waste stream. Studies indicate that re-melting NORM-contaminated scrap metal is a viable recycling option from a risk-based perspective. However, a myriad of economic, regulatory, and policy issues have caused the recyclers to turn away virtually all radioactive scrap metal. Until these issues can be resolved, re-melting of the petroleum industry's NORM-impacted scrap metal is unlikely to be a widespread practice. This paper summarizes the issues associated with re-melting radioactive scrap so that the petroleum industry and its regulators will understand the obstacles. This paper was prepared as part of a report being prepared by the Interstate Oil and Gas Compact Commission's NORM Subcommittee.

  14. Fabrication of metallic alloy powder (Ni{sub 3}Fe) from Fe–77Ni scrap

    Energy Technology Data Exchange (ETDEWEB)

    Seo, Inseok [ES Materials Research Center, Research Institute of Industrial Science and Technology, Incheon 406-840 (Korea, Republic of); Shin, Shun-Myung [Extractive Metallurgy Department, Korea Institute of Geoscience and Mineral Resources, Deajeon 305-350 (Korea, Republic of); Ha, Sang-An [Department of Environmental Engineering, Silla University, Busan 46958 (Korea, Republic of); Wang, Jei-Pil, E-mail: jpwang@pknu.ac.kr [Department of Metallurgical Engineering, Pukyong National University, Busan 608-739 (Korea, Republic of)

    2016-06-15

    The oxidation behavior of Fe–77Ni alloy scrap was investigated at an oxygen partial pressure of 0.2 atm and temperatures ranging from 400 °C to 900 °C. The corresponding oxidation rate increased with increasing temperature and obeyed the parabolic rate law, as evidenced by its linear proportionality to the temperature. In addition, surface morphologies, cross-sectional views, compositions, structural properties were examined by scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and X-ray diffraction (XRD). Diffusion through either the spinel structure or the NiO layer, which were both present in the alloy during oxidation at elevated temperatures, was deemed the rate-limiting step of the reaction. The oxide powder less than 10 μm was obtained from Fe–77Ni alloy scrap was obtained using ball-milling and sieving processes. In fact, 15 h of milling yielded a recovery ratio of 97%. Using hydrogen gas, the oxide powder was successfully reduced to an alloy powder of Ni{sub 3}Fe and reduction rates of ∼97% were achieved after 3 h at 1000 °C. - Highlights: • The oxidation behavior of Fe–77Ni alloy scrap was investigated. • The oxide powder less than 10 μm was obtained from Fe–77Ni alloy scrap. • Using hydrogen gas, the oxide powder was successfully reclaimed. • Reduction rates of ∼97% were achieved after 3 h at 1000 °C.

  15. Technical Review of the Characteristics of Spent Nuclear Fuel Scrap

    International Nuclear Information System (INIS)

    Kuhn, William L.; Abrefah, John; Pitner, Allen L.; Damschen, Dennis W.

    2000-01-01

    Spent Nuclear Fuel scrap generated while washing the SNF in Hanford's K-Basins to prepare it for cold vacuum drying differed significantly from that envisioned during project design. Therefore, a technical review panel evaluated the new information about the physical characteristics of scrap generated during processing by characterizing it based on measured weights and digital photographic images. They examined images of the scrap and from them estimated the volume and hence the masses of inert material and of large fragments of spent fuel. The panel estimated the area of these particles directly from images and by fitting a lognormal distribution to the relative number particles in four size ranges and then obtaining the area-to-volume ratio from the distribution. The estimated area is 0.3 m2 for the mass of scrap that could be loaded into a container for drying, which compares to a value of 4.5 m2 assumed for safe operation of the baseline process. The small quantity of scrap genera ted is encouraging. However, the size and mass of the scrap depend both on processes degrading the fuel while in the basin and on processes catching the scrap during washing, the latter including essentially unintentional filtration as debris accumulates. Therefore, the panel concluded that the estimated surface area meets the criterion for loading scrap into an MCO for drying, but because it did not attempt to evaluate the criterion itself, it is not in a position to actually recommend loading the scrap. Further, this is not a sufficiently strong technical position from which to extrapolate the results from the examined scrap to all future scrap generated by the existing process

  16. Management options for recycling radioactive scrap metals

    Energy Technology Data Exchange (ETDEWEB)

    Dehmel, J.C.; MacKinney, J.; Bartlett, J.

    1997-02-01

    The feasibility and advantages of recycling radioactive scrap metals (RSM) have yet to be assessed, given the unique technical, regulatory, safety, and cost-benefit issues that have already been raised by a concerned recycling industry. As is known, this industry has been repeatedly involved with the accidental recycling of radioactive sources and, in some cases, with costly consequences. If recycling were deemed to be a viable option, it might have to be implemented with regulatory monitoring and controls. Its implementation may have to consider various and complex issues and address the requirements and concerns of distinctly different industries. There are three basic options for the recycling of such scraps. They are: (1) recycling through the existing network of metal-scrap dealers and brokers, (2) recycling directly and only with specific steelmills, or (3) recycling through regional processing centers. Under the first option, scrap dealers and brokers would receive material from RSM generators and determine at which steelmills such scraps would be recycled. For the second option, RSM generators would deal directly with selected steelmills under specific agreements. For the third option, generators would ship scraps only to regional centers for processing and shipment to participating steelmills. This paper addresses the potential advantages of each option, identifies the types of arrangements that would need to be secured among all parties, and attempts to assess the receptivity of the recycling industry to each option.

  17. Evaluation of workability and strength of green concrete using waste steel scrap

    Science.gov (United States)

    Neeraja, D.; Arshad, Shaik Mohammed; Nawaz Nadaf, Alisha K.; Reddy, Mani Kumar

    2017-11-01

    This project works on the study of workability and mechanical properties of concrete using waste steel scrap from the lathe industry. Lathe industries produce waste steel scrap from the lathe machines. In this study, an attempt is made to use this waste in concrete, as accumulation of waste steel scrap cause disposal problem. Tests like compressive test, split tensile test, NDT test (UPV test) were conducted to determine the impact of steel scrap in concrete. The percentages of steel scrap considered in the study were 0%, 0.5%, 1%, 1.5%, and 2% respectively by volume of concrete, 7 day, 28 days test were conducted to find out strength of steel scrap concrete. It is observed that split tensile strength of steel scrap concrete is increased slightly. Split tensile strength of Steel scrap concrete is found to be maximum with volume fraction of 2.0% steel scrap. The steel scrap gives good result in split tensile strength of concrete. From the study concluded that steel scrap can be used in concrete to reduce brittleness of concrete to some extent.

  18. Detection of radioactivity in scrap in Germany

    International Nuclear Information System (INIS)

    Kugeler, E.; Thierfeldt, S.; Sefzig, R.; Weimer, G.

    1999-01-01

    Although Germany's scrap export exceeds the import, the imports of scrap amount to more than one million Mg per year. Radioactivity has been found mainly in imported scrap in Germany. This radioactivity can consist of surface contamination in scrap e.g. from the oil and gas industry, nuclear and other technical applications or of radiation sources, e.g. from medical or technical irradiation devices where the source has not been removed prior to scrapping. Fortunately really large sources have been involved in only very few occasions. More serious incidents have, however, been reported from other countries. Today, measurement facilities have been installed at the entrances to virtually all German foundries and larger scrap yards. These measurement facilities allow the swift measurement of whole lorry or freight car loads. The lower limit of detection is for some devices as low as ca. 5 nSv/h (dose rate increase above background at the detector) which is achieved by very advanced hardware and software. Additionally, simplified dose rate measurements are performed by German customs officials at the eastern borders for scrap loads to be imported into Germany. When activity is detected in a load, several options exist, like e.g.: (i) sending the scrap back to the sender; (ii) allowing the whole load to be melted down; (iii) careful unloading and separating the load with the aim of localizing and removing the contamination. This paper analyses these various options after detection, discusses the role of the competent authorities and evaluates the possible radiological consequences. Realistic dose calculations show that it is possible that a person may receive doses of several mSv or even 10 mSv if precautionary measures are neglected or if a larger source is not detected at all. This paper further addresses which types and amounts of radioactivity may be detected and which conclusions can be drawn from the dose rate at the detector. The continuous increase in the number

  19. Classification of scrap material from nuclear power plants as acceptable for recirculation

    International Nuclear Information System (INIS)

    Bergman, C.

    1983-06-01

    The Swedish National Institute of Radiation Protection has in a principal decision accepted that scrap material from nuclear power plants, that contains or may contain radioactive material, can be recirculated. The document is an English translation of the background material for the Board meeting decision and gives some guide-lines for the authority when dealing with this questions. (author)

  20. Recovery of uranium from (U,Gd)O{sub 2} nuclear fuel scrap using dissolution and precipitation in carbonate media

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Kwang-Wook, E-mail: nkwkim@kaeri.re.kr [Korea Atomic Energy Research Institute, 1045 Daedeok daero, Yuseong, Daejeon 305-353 (Korea, Republic of); KEPCO NF 1047 Daedeok daero, Yuseong, Daejeon 305-353 (Korea, Republic of); Hyun, Jun-Taek; Lee, Eil-Hee; Park, Geun-Il; Lee, Kune-Woo [Korea Atomic Energy Research Institute, 1045 Daedeok daero, Yuseong, Daejeon 305-353 (Korea, Republic of); Yoo, Myung-June [KEPCO NF 1047 Daedeok daero, Yuseong, Daejeon 305-353 (Korea, Republic of); Song, Kee-Chan; Moon, Jei-Kwon [Korea Atomic Energy Research Institute, 1045 Daedeok daero, Yuseong, Daejeon 305-353 (Korea, Republic of)

    2011-11-15

    Highlights: > A treatment of (U,Gd)O{sub 2} scrap with a dissolution in carbonate solution with H{sub 2}O{sub 2}. > Partial dissolution of Gd together with uranium in carbonate solution. > Solubilities of Gd in solutions with and without carbonate at several pHs. > Purification of Gd-contaminated UO{sub 4} by dissolution and precipitation of UO{sub 4}. - Abstract: This work studied a process to recover uranium from contaminated (U,Gd)O{sub 2} scraps generated from nuclear fuel fabrication processes by using the dissolution of (U,Gd)O{sub 2} scraps in a carbonate with H{sub 2}O{sub 2} and the precipitation of the dissolved uranium as UO{sub 4}. The dissolution characteristics of uranium, Gd, and impurity metal oxides were tested, and the behaviors of UO{sub 4} precipitation and Gd solubility were evaluated with changes of the pH of the solution. A little Gd was entrained in the UO{sub 4} precipitate to contaminate the uranium precipitate. Below a pH of 3, the uranium dissolved in the form of uranyl peroxo-carbonato complex ions in the carbonate solution was precipitated as UO{sub 4} with a high precipitation yield, and the Gd had a very high solubility. Using these characteristics, the Gd-contaminated UO{sub 4} could be purified using dissolution in a 1-M HNO{sub 3} solution with heating and re-precipitation upon addition of H{sub 2}O{sub 2} to the solution. Finally, an environmentally friendly and economical process to recover pure uranium from contaminated (U,Gd)O{sub 2} scraps was suggested.

  1. Mercury-impacted scrap metal: Source and nature of the mercury.

    Science.gov (United States)

    Finster, Molly E; Raymond, Michelle R; Scofield, Marcienne A; Smith, Karen P

    2015-09-15

    The reuse and recycling of industrial solid wastes such as scrap metal is supported and encouraged both internationally and domestically, especially when such wastes can be used as substitutes for raw material. However, scrap metal processing facilities, such as mini-mills, have been identified as a source of mercury (Hg) emissions in the United States. This research aims to better define some of the key issues related to the source and nature of mercury in the scrap metal waste stream. Overall, it is difficult to pinpoint the key mercury sources feeding into scrap metal recycling facilities, quantify their associated mercury concentrations, or determine which chemical forms are most significant. Potential sources of mercury in scrap metal include mercury switches from discarded vehicles, electronic-based scrap from household appliances and related industrial systems, and Hg-impacted scrap metal from the oil and gas industry. The form of mercury associated with scrap metal varies and depends on the source type. The specific amount of mercury that can be adsorbed and retained by steel appears to be a function of both metallurgical and environmental factors. In general, the longer the steel is in contact with a fluid or condensate that contains measurable concentrations of elemental mercury, the greater the potential for mercury accumulation in that steel. Most mercury compounds are thermally unstable at elevated temperatures (i.e., above 350 °C). As such, the mercury associated with impacted scrap is expected to be volatilized out of the metal when it is heated during processing (e.g., shredding or torch cutting) or melted in a furnace. This release of fugitive gas (Hg vapor) and particulates, as well as Hg-impacted bag-house dust and control filters, could potentially pose an occupational exposure risk to workers at a scrap metal processing facility. Thus, identifying and characterizing the key sources of Hg-impacted scrap, and understanding the nature and extent

  2. Effects of hemoglobin variants HbJ Bangkok, HbE, HbG Taipei, and HbH on analysis of glycated hemoglobin via ion-exchange high-performance liquid chromatography.

    Science.gov (United States)

    Zhang, Xiu-Ming; Wen, Dong-Mei; Xu, Sheng-Nan; Suo, Ming-Huan; Chen, Ya-Qiong

    2018-01-01

    To explore the effects of HbJ Bangkok, HbE, HbG Taipei, and α-thalassemia HbH on the results of HbA1c assessment using ion-exchange high-performance liquid chromatography (IE-HPLC). We enrolled five patients in which the results of the IE-HPLC HbA1c assay were inconsistent with the average levels of FBG. We performed hemoglobin capillary (Hb) electrophoresis using whole-blood samples. We also sequenced the genes encoding Hb using dideoxy-mediated chain termination and analyzed HbA1c using borate affinity HPLC (BA-HPLC) and turbidimetric inhibition immunoassay (TINIA). Two patients had the HbJ Bangkok variant. Hb genotypes of these patients were β 41-42 /β J Bangkok and β N /β J Bangkok , and the content of HbJ Bangkok was 93.9% and 52.4%, respectively. The remaining three patients had the following: HbE (β N /β E Hb genotype, 23.6% HbE content), HbG Taipei (β N /β G Taipei Hb genotype, 39.4% HbG Taipei content), and α-thalassemia HbH (6.1% HbH content, 2.8% Hb Bart's content). In the patients with β-thalassemia and HbJ Bangkok variants, the presence of the variants interfered with the results of HbA1c analyses using IE-HPLC and TINIA; in the remaining four patients, there was interference with the results of HbA1c IE-HPLC but not with the TINIA assay. There was no interference with BA-HPLC HbA1c results. HbJ Bangkok, HbE, HbG Taipei Hb, and α-thalassemia HbH disease cause varying degrees of interference with the analysis of HbA1c using IE-HPLC. In these patients, we suggest using methods free from such interference for the analysis of HbA1c and other indicators to monitor blood glucose levels. © 2017 Wiley Periodicals, Inc.

  3. Recovery Strategies in On-Line Service Failure

    OpenAIRE

    Ozuem, Wilson; Lancaster, Geoff

    2013-01-01

    Despite a proliferation of a number of studies on service failures and recovery in e-service settings, there is a paucity of knowledge of ways in which service failures and recovery practices are implemented in the fashion industry. Drawing on constructivist perspective, this study offers a new perspective on an effective relational mechanism that would bridge the rupture between consumers and companies particularly in the on-line fashion sector. The analysis adds to studies on service failur...

  4. 49 CFR 173.218 - Fish meal or fish scrap.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Fish meal or fish scrap. 173.218 Section 173.218... Fish meal or fish scrap. (a) Except as provided in Column (7) of the HMT in § 172.101 of this subchapter, fish meal or fish scrap, containing at least 6%, but not more than 12% water, is authorized for...

  5. Economic comparison of management modes for contaminated metal scrap

    International Nuclear Information System (INIS)

    Janberg, K.

    1987-01-01

    This report presents an economic study of the three following management modes for contaminated metal scrap: - decontamination of scrap metal followed by release, - direct melting of scrap metal, followed by release or restricted reuse, - super-compaction followed by disposal as radioactive waste. The present study, which refers to conditions prevailing in Germany, includes reviews of the contaminated scrap arisings, of experience with scrap management and of the licensing conditions for metal recycling. The results obtained during the treatment of more than 140 t of contaminated scrap metal show that: - super-compaction is the best procedure for all mixed metallic wastes of small dimensions and complex geometries, as decontamination is very costly in such a case and the melting would lead to undefined metallurgical products; - decontamination is recommendable for simple geometries and activities higher than the regulatory upper limit for melting in an industrial foundry (74 Bq/g); - direct melting for lower activity levels is gaining in competitiveness and has a good chance to be the best solution, in particular when the free use levels will be reduced below the currently accepted levels in Germany

  6. Nuclear translocation of the cytoplasmic domain of HB-EGF induces gastric cancer invasion

    Directory of Open Access Journals (Sweden)

    Shimura Takaya

    2012-05-01

    Full Text Available Abstract Background Membrane-anchored heparin-binding epidermal growth factor-like growth factor (proHB-EGF yields soluble HB-EGF, which is an epidermal growth factor receptor (EGFR ligand, and a carboxy-terminal fragment of HB-EGF (HB-EGF-CTF after ectodomain shedding. We previously reported that HB-EGF-CTF and unshed proHB-EGF which has the cytoplasmic domain of proHB-EGF (HB-EGF-C, translocate from the plasma membrane to the nucleus and regulate cell cycle after shedding stimuli. However, the significance of nuclear exported HB-EGF-C in human gastric cancer is unclear. Methods We investigated the relationship between intracellular localization of HB-EGF-C and clinical outcome in 96 gastric cancer patients treated with gastrectomy. Moreover, we established stable gastric cancer cell lines overexpressing wild-type HB-EGF (wt-HB-EGF and mutated HB-EGF (HB-EGF-mC, which prevented HB-EGF-C nuclear translocation after shedding. Cell motility between these 2 gastric cancer cell lines was investigated using a transwell invasion assay and a wound healing assay. Results Of the 96 gastric cancer cases, HB-EGF-C immunoreactivity was detected in both the nucleus and cytoplasm in 19 cases (19.8 % and in the cytoplasm only in 25 cases (26.0 %. The nuclear immunoreactivity of HB-EGF-C was significantly increased in stage pT3/4 tumors compared with pT1/2 tumors (T1/2 vs. T3/4: 11.1 % vs. 36.4 %, P  Conclusions Both the function of HB-EGF as an EGFR ligand and a novel signal for HB-EGF-C nuclear translocation induce gastric cancer growth, whereas HB-EGF-C nuclear translocation independently plays a critical role in gastric cancer invasion. The present study demonstrated that HB-EGF-C nuclear translocation might be crucial in gastric cancer invasion. HB-EGF-C nuclear translocation may offer a prognostic marker and a new molecular target for gastric cancer therapy.

  7. The steel scrap age.

    Science.gov (United States)

    Pauliuk, Stefan; Milford, Rachel L; Müller, Daniel B; Allwood, Julian M

    2013-04-02

    Steel production accounts for 25% of industrial carbon emissions. Long-term forecasts of steel demand and scrap supply are needed to develop strategies for how the steel industry could respond to industrialization and urbanization in the developing world while simultaneously reducing its environmental impact, and in particular, its carbon footprint. We developed a dynamic stock model to estimate future final demand for steel and the available scrap for 10 world regions. Based on evidence from developed countries, we assumed that per capita in-use stocks will saturate eventually. We determined the response of the entire steel cycle to stock saturation, in particular the future split between primary and secondary steel production. During the 21st century, steel demand may peak in the developed world, China, the Middle East, Latin America, and India. As China completes its industrialization, global primary steel production may peak between 2020 and 2030 and decline thereafter. We developed a capacity model to show how extensive trade of finished steel could prolong the lifetime of the Chinese steelmaking assets. Secondary steel production will more than double by 2050, and it may surpass primary production between 2050 and 2060: the late 21st century can become the steel scrap age.

  8. Properties of concrete containing scrap-tire rubber--an overview.

    Science.gov (United States)

    Siddique, Rafat; Naik, Tarun R

    2004-01-01

    Solid waste management is one of the major environmental concerns in the United States. Over 5 billion tons of non-hazardous solid waste materials are generated in USA each year. Of these, more than 270 million scrap-tires (approximately 3.6 million tons) are generated each year. In addition to this, about 300 million scrap-tires have been stockpiled. Several studies have been carried out to reuse scrap-tires in a variety of rubber and plastic products, incineration for production of electricity, or as fuel for cement kilns, as well as in asphalt concrete. Studies show that workable rubberized concrete mixtures can be made with scrap-tire rubber. This paper presents an overview of some of the research published regarding the use of scrap-tires in portland cement concrete. The benefits of using magnesium oxychloride cement as a binder for rubberized concrete mixtures are also presented. The paper details the likely uses of rubberized concrete.

  9. Molecular analysis of Hb Q-H disease and Hb Q-Hb E in a Singaporean family.

    Science.gov (United States)

    Tan, J; Tay, J S; Wong, Y C; Kham, S K; Bte Abd Aziz, N; Teo, S H; Wong, H B

    1995-01-01

    Hb Q (alpha 74Asp-His) results from a mutation in the alpha-gene such that abnormal alpha Q-chains are synthesized. The alpha Q-chains combine with the normal Beta A-chains to form abnormal Hb alpha 2Q beta 2A (Hb Q). Hb Q-H disease is rare, and has been reported only in the Chinese. We report here a Chinese family, were the mother diagnosed with Hb Q-H disease and the father with Hb E heterozygosity and a child with Hb Q-E-thalassemia. Thalassemia screening of the mother's blood revealed a Hb level of 6.8g/dl with low MCV and MCH. Her blood film was indicative of thalassemia. Cellulose acetate electrophoresis showed Hb H and Hb Q with the absence of Hb A. Globin chain biosynthesis was carried out and alpha Q- and beta-chains were detected. Normal alpha- chains were absent. Digestion of the mother's DNA with Bam HI and Bgl II followed by hybridization with the 1.5 kb alpha-Pst probe showed a two alpha-gene deletion on one chromosome and the -alpha Q chain mutant with the -alpha 4.2 defect on the other chromosome. DNA amplification studies indicated the two-gene deletion to be of the -SEA/ defect. The patient was concluded to possess Hb Q-H disease (--SEA/-alpha 4.2Q). Cellulose acetate electrophoresis of the father's blood showed the presence of Hb A, F and E. Molecular analysis of the father's DNA confirmed an intact set of alpha-genes (alpha alpha/alpha alpha). Globin chain biosynthesis of fetal blood of their child showed gamma, beta A, beta E, alpha A and alpha Q-chains. Molecular analysis of the child's DNA showed one alpha-gene deletion, thus giving a genotype of alpha alpha/-alpha 4.2Q beta beta E.

  10. Nuclear translocation of the cytoplasmic domain of HB-EGF induces gastric cancer invasion.

    Science.gov (United States)

    Shimura, Takaya; Yoshida, Michihiro; Fukuda, Shinji; Ebi, Masahide; Hirata, Yoshikazu; Mizoshita, Tsutomu; Tanida, Satoshi; Kataoka, Hiromi; Kamiya, Takeshi; Higashiyama, Shigeki; Joh, Takashi

    2012-05-30

    Membrane-anchored heparin-binding epidermal growth factor-like growth factor (proHB-EGF) yields soluble HB-EGF, which is an epidermal growth factor receptor (EGFR) ligand, and a carboxy-terminal fragment of HB-EGF (HB-EGF-CTF) after ectodomain shedding. We previously reported that HB-EGF-CTF and unshed proHB-EGF which has the cytoplasmic domain of proHB-EGF (HB-EGF-C), translocate from the plasma membrane to the nucleus and regulate cell cycle after shedding stimuli. However, the significance of nuclear exported HB-EGF-C in human gastric cancer is unclear. We investigated the relationship between intracellular localization of HB-EGF-C and clinical outcome in 96 gastric cancer patients treated with gastrectomy. Moreover, we established stable gastric cancer cell lines overexpressing wild-type HB-EGF (wt-HB-EGF) and mutated HB-EGF (HB-EGF-mC), which prevented HB-EGF-C nuclear translocation after shedding. Cell motility between these 2 gastric cancer cell lines was investigated using a transwell invasion assay and a wound healing assay. Of the 96 gastric cancer cases, HB-EGF-C immunoreactivity was detected in both the nucleus and cytoplasm in 19 cases (19.8 %) and in the cytoplasm only in 25 cases (26.0 %). The nuclear immunoreactivity of HB-EGF-C was significantly increased in stage pT3/4 tumors compared with pT1/2 tumors (T1/2 vs. T3/4: 11.1 % vs. 36.4 %, P Gastric cancer cell invasion obviously increased in wt-HB-EGF-expressing cells, but invasion in HB-EGF-mC-expressing cells showed a slight increase compared with control cells. Moreover, wt-HB-EGF overexpression increased the effectiveness of wound healing, but had no significant effect in HB-EGF-mC-expressing cells. Both the function of HB-EGF as an EGFR ligand and a novel signal for HB-EGF-C nuclear translocation induce gastric cancer growth, whereas HB-EGF-C nuclear translocation independently plays a critical role in gastric cancer invasion. The present study demonstrated that HB-EGF-C nuclear translocation

  11. Results of chemical decontamination of DOE`s uranium-enrichment scrap metal

    Energy Technology Data Exchange (ETDEWEB)

    Levesque, R.G.

    1997-02-01

    The CORPEX{reg_sign} Nuclear Decontamination Processes were used to decontaminate representative scrap metal specimens obtained from the existing scrap metal piles located at the Department of Energy (DOE) Portsmouth Gaseous Diffusion Plant (PORTS), Piketon, Ohio. In September 1995, under contract to Lockheed Martin Energy Systems, MELE Associates, Inc. performed the on-site decontamination demonstration. The decontamination demonstration proved that significant amounts of the existing DOE scrap metal can be decontaminated to levels where the scrap metal could be economically released by DOE for beneficial reuse. This simple and environmentally friendly process can be used as an alternative, or in addition to, smelting radiologically contaminated scrap metal.

  12. Analysis of disposition alternatives for radioactively contaminated scrap metal

    International Nuclear Information System (INIS)

    Nieves, L.A.; Chen, S.Y.; Kohout, E.J.; Nabelssi, B.; Tilbrook, R.W.; Wilson, S.E.

    1997-01-01

    Millions of tonnes of slightly radioactive, scrap iron and steel, stainless steel, and copper are likely to become available as nuclear and other facilities and equipment are withdrawn from service. Disposition of this material is an international policy issue under consideration currently. The major alternatives for managing this material are to either develop a regulatory process for decontamination and recycling that will safeguard human health or to dispose of the scrap and replace the metal stocks. To evaluate the alternatives, we estimate quantities of scrap arising from nuclear power plant decommissioning, evaluate potential price impacts of recycling on regional markets, and assess the health and environmental impacts of the management alternatives. We conclude that decontaminating and recycling the scrap is the superior alternative

  13. Radiation survey of aircraft and heavy machinery scrap.

    Science.gov (United States)

    Idriss, Hajo; Salih, Isam; Gumaa, Elsadig; Yassin, Abbas; Yousif, E H; Abdel Hamid, Saad Eldeen M; Sam, A K

    2012-12-01

    This study was conducted primarily to survey aircraft and heavy machinery at 30 locations within Khartoum State using handheld radiation survey meters to detect and identify any radiation sources that might be present and to estimate radiation dose levels. The survey has resulted in detection of 16 sealed sources of (90)Sr and one of (226)Ra in aircraft scrap. Of course, (90)Sr sources are used in military aircraft as temperature sensors while (226)Ra is used for indicating fuel levels. These sources were found intact without spreading radioactivity contamination; however, none was detected in heavy machine scrap. The levels of radiation dose measured at 0.1m from the source fall within the range of 25.1-40.2 μSv/h with an average value of 33.52 ± 4.06 μSv/h. These orphan sources have been separated from the scrap, tested for possible leakage, conditioned and stored in waste management facility. The result of this study has revealed without doubt that the scrap constitute a serious source of public exposure and highlights the importance of legislation making radiation monitoring of scrap in the country mandatory before it is sold to metal industry for reprocessing. Copyright © 2012 Elsevier Ltd. All rights reserved.

  14. Erroneous HbA1c results in a patient with elevated HbC and HbF.

    Science.gov (United States)

    Adekanmbi, Joy; Higgins, Trefor; Rodriguez-Capote, Karina; Thomas, Dylan; Winterstein, Jeffrey; Dixon, Tara; Gifford, Jessica L; Krause, Richard; Venner, Allison A; Clarke, Gwen; Estey, Mathew P

    2016-11-01

    HbA1c is used in the diagnosis and monitoring of diabetes mellitus (DM). Interference from hemoglobin variants is a well-described phenomenon, particularly with HPLC-based methods. While immunoassays may generate more reliable HbA1c results in the presence of some variants, these methods are susceptible to negative interference from high concentrations of HbF. We report a case where an accurate HbA1c result could not be obtained by any available method due to the presence of a compound hemoglobinopathy. HbA1c was measured by HPLC, immunoassay, and capillary electrophoresis. Hemoglobinopathy investigation consisted of a CBC, hemoglobin fractionation by HPLC and electrophoresis, and molecular analysis. HbA1c analysis by HPLC and capillary electrophoresis gave no result. Analysis by immunoassay yielded HbA1c results of 5.9% (Siemens DCA 2000+) and 5.1% (Roche Integra), which were inconsistent with other markers of glycemic control. Hemoglobinopathy investigation showed HbC with the hereditary persistence of fetal hemoglobin-2 Ghana deletion. Reliable HbA1c results may be unobtainable in the presence of some hemoglobinopathies. HPLC and capillary electrophoresis alerted the laboratory to the presence of an unusual hemoglobinopathy. Immunoassays generated falsely low results without warning, which could lead to missed diagnoses and under treatment of patients with DM. Copyright © 2016 Elsevier B.V. All rights reserved.

  15. Contaminated scrap metal management on the Oak Ridge Reservation

    International Nuclear Information System (INIS)

    Hayden, H.W.; Stephenson, M.J.; Bailey, J.K.; Weir, J.R.; Gilbert, W.C.

    1993-01-01

    Large quantities of scrap metal are accumulating at the various Department of Energy (DOE) installations across the country as a result of ongoing DOE programs and missions in concert with present day waste management practices. DOE Oak Ridge alone is presently storing around 500,000 tons of scrap metal. The local generation rate, currently estimated at 1,400 tons/yr, is expected to increase sharply over the next couple of years as numerous environmental restoration and decommissioning programs gain momentum. Projections show that 775,000 tons of scrap metal could be generated at the K-25 Site over the next ten years. The Y-12 Plant and Oak Ridge National Laboratory (ORNL) have similar potentials. The history of scrap metal management at Oak Ridge and future challenges and opportunities are discussed

  16. A novel double heterozygous Hb Fontainebleau/HbD Punjab hemoglobinopathy.

    Science.gov (United States)

    Rodríguez-Capote, Karina; Estey, Mathew P; Barakauskas, Vilte; Bordeleau, Pierre; Christensen, Cathie-Lou; Zuberbuhler, Peter; Higgins, Trefor N

    2015-09-01

    To report the finding of a novel double heterozygous hemoglobinopathy, the coinheritance of Hb Fontainebleau (α-chain variant) with HbD-Punjab (β-chain variant) discovered upon investigation of unexplained microcytosis in an infant. Hemoglobinopathy investigation was performed by high performance liquid chromatography (HPLC) using the β-thalassemia Short Program on the Bio-Rad Variant II(TM) followed by gel electrophoresis at alkaline and acid pH (Sebia Hydrasys 2 Electrophoresis System) and molecular diagnostic testing. This study complied with our institutional board ethics requirements. HPLC and electrophoresis suggested a complex α- and β-chain hemoglobinopathy with presumptive identification of the beta Hb variant as Hb D-Punjab. DNA sequencing analysis revealed the presence of a double heterozygous status for Hb Fontainebleau/Hb D-Punjab. In this paper we report the coinheritance of Hb Fontainebleau with Hb D-Punjab. Copyright © 2015 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

  17. Nuclear translocation of the cytoplasmic domain of HB-EGF induces gastric cancer invasion

    International Nuclear Information System (INIS)

    Shimura, Takaya; Higashiyama, Shigeki; Joh, Takashi; Yoshida, Michihiro; Fukuda, Shinji; Ebi, Masahide; Hirata, Yoshikazu; Mizoshita, Tsutomu; Tanida, Satoshi; Kataoka, Hiromi; Kamiya, Takeshi

    2012-01-01

    Membrane-anchored heparin-binding epidermal growth factor-like growth factor (proHB-EGF) yields soluble HB-EGF, which is an epidermal growth factor receptor (EGFR) ligand, and a carboxy-terminal fragment of HB-EGF (HB-EGF-CTF) after ectodomain shedding. We previously reported that HB-EGF-CTF and unshed proHB-EGF which has the cytoplasmic domain of proHB-EGF (HB-EGF-C), translocate from the plasma membrane to the nucleus and regulate cell cycle after shedding stimuli. However, the significance of nuclear exported HB-EGF-C in human gastric cancer is unclear. We investigated the relationship between intracellular localization of HB-EGF-C and clinical outcome in 96 gastric cancer patients treated with gastrectomy. Moreover, we established stable gastric cancer cell lines overexpressing wild-type HB-EGF (wt-HB-EGF) and mutated HB-EGF (HB-EGF-mC), which prevented HB-EGF-C nuclear translocation after shedding. Cell motility between these 2 gastric cancer cell lines was investigated using a transwell invasion assay and a wound healing assay. Of the 96 gastric cancer cases, HB-EGF-C immunoreactivity was detected in both the nucleus and cytoplasm in 19 cases (19.8 %) and in the cytoplasm only in 25 cases (26.0 %). The nuclear immunoreactivity of HB-EGF-C was significantly increased in stage pT3/4 tumors compared with pT1/2 tumors (T1/2 vs. T3/4: 11.1 % vs. 36.4 %, P < 0.01). The growth of wt-HB-EGF- and HB-EGF-mC-expressing cells significantly increased compared with control cells, but the growth of HB-EGF-mC-expressing cells was significantly decreased compared with wt-HB-EGF-expressing cells. Gastric cancer cell invasion obviously increased in wt-HB-EGF-expressing cells, but invasion in HB-EGF-mC-expressing cells showed a slight increase compared with control cells. Moreover, wt-HB-EGF overexpression increased the effectiveness of wound healing, but had no significant effect in HB-EGF-mC-expressing cells. Both the function of HB-EGF as an EGFR ligand and a novel signal for

  18. Nuclear translocation of the cytoplasmic domain of HB-EGF induces gastric cancer invasion

    Science.gov (United States)

    2012-01-01

    Background Membrane-anchored heparin-binding epidermal growth factor-like growth factor (proHB-EGF) yields soluble HB-EGF, which is an epidermal growth factor receptor (EGFR) ligand, and a carboxy-terminal fragment of HB-EGF (HB-EGF-CTF) after ectodomain shedding. We previously reported that HB-EGF-CTF and unshed proHB-EGF which has the cytoplasmic domain of proHB-EGF (HB-EGF-C), translocate from the plasma membrane to the nucleus and regulate cell cycle after shedding stimuli. However, the significance of nuclear exported HB-EGF-C in human gastric cancer is unclear. Methods We investigated the relationship between intracellular localization of HB-EGF-C and clinical outcome in 96 gastric cancer patients treated with gastrectomy. Moreover, we established stable gastric cancer cell lines overexpressing wild-type HB-EGF (wt-HB-EGF) and mutated HB-EGF (HB-EGF-mC), which prevented HB-EGF-C nuclear translocation after shedding. Cell motility between these 2 gastric cancer cell lines was investigated using a transwell invasion assay and a wound healing assay. Results Of the 96 gastric cancer cases, HB-EGF-C immunoreactivity was detected in both the nucleus and cytoplasm in 19 cases (19.8 %) and in the cytoplasm only in 25 cases (26.0 %). The nuclear immunoreactivity of HB-EGF-C was significantly increased in stage pT3/4 tumors compared with pT1/2 tumors (T1/2 vs. T3/4: 11.1 % vs. 36.4 %, P HB-EGF- and HB-EGF-mC-expressing cells significantly increased compared with control cells, but the growth of HB-EGF-mC-expressing cells was significantly decreased compared with wt-HB-EGF-expressing cells. Gastric cancer cell invasion obviously increased in wt-HB-EGF-expressing cells, but invasion in HB-EGF-mC-expressing cells showed a slight increase compared with control cells. Moreover, wt-HB-EGF overexpression increased the effectiveness of wound healing, but had no significant effect in HB-EGF-mC-expressing cells. Conclusions Both the function of HB-EGF as an EGFR ligand

  19. Comparison of the characteristics of two hemoglobin variants, Hb D-Iran and Hb E, eluting in the Hb A2 window.

    Science.gov (United States)

    Dass, Jasmita; Gupta, Aastha; Mittal, Suchi; Saraf, Amrita; Langer, Sabina; Bhargava, Manorama

    2017-06-01

    Cation exchange-high performance liquid chromatography (CE-HPLC) is most commonly used to evaluate hemoglobin (Hb) variants, which elute in the Hb A2 window. This study aimed to assess prevalence of an uncommon Hb variant, Hb D-Iran, and compare its red cell parameters and peak characteristics with those of Hb E that commonly elutes in the Hb A2 window. Generally, we assess abnormal Hb using CE-HPLC as the primary technique along with alkaline and acid electrophoresis. All cases with Hb A2 window >9%, as assessed by CE-HPLCs during 2009-2013, were selected. Twenty-nine cases with Hb D-Iran variant were identified-25 heterozygous, 2 homozygous, 1 compound heterozygous Hb D-Iran/β-thalassemia, and 1 Hb D-Iran/Hb D-Punjab. Overall prevalence of Hb D-Iran was 0.23%. Compared to patients with Hb E, those with Hb D-Iran had significantly higher Hb (12.1 vs. 11.3 g/dL, P =0.03), MCV (82.4 vs. 76.4 fL, P =0.0044), MCH (27.9 vs. 25.45 pg, P =0.0006), and MCHC (33.9 vs. 33.3 g/dL, P =0.0005). Amount of abnormal Hb (40.7 vs. 26.4%, P =0.0001) was significantly higher while retention time (3.56 vs. 3.70 min, P =0.0001) was significantly lower in Hb D-Iran than in Hb E. Hb D-Iran peak can be easily missed if area and retention time of the Hb A2 window are not carefully analyzed. To distinguish between variants, careful analysis of peak area and retention time is sufficient in most cases and may be further confirmed by the second technique-alkaline electrophoresis.

  20. Y-12 old salvage yard scrap metal characterization study

    International Nuclear Information System (INIS)

    Anderson, L.M.; Melton, S.G.; Shaw, S.S.

    1993-11-01

    The purpose of the Y-12 Old Salvage Yard scrap metal Characterization Study is to make conservative estimates of the quantities of total uranium and the wt % 235 U contained in scrap metal. The original project scope included estimates of thorium, but due to the insignificant quantities found in the yards, thorium was excluded from further analysis. Metal in three of the four Y-12 scrap metal yards were characterized. The scrap metal yard east of the PIDAS fence is managed by the Environmental Restoration Program and therefore was not included in this study. For all Y-12 Plant scrap metal shipments, Waste Transportation, Storage, and Disposal (WTSD) personnel must complete a Request for Authorization to Ship Nuclear Materials, UCN-16409, which requires the grams of total uranium, the wt % 235 U, and the grams of 235 U contained in the shipment. This information is necessary to ensure compliance with Department of Transportation regulations, as well as to ensure that the receiving facility is adhering to its operating license. This characterization study was designed to provide a technical basis for determining these necessary radioactive quantities

  1. CHANGING THE LANDSCAPE--LOW-TECH SOLUTIONS TO THE PADUCAH SCRAP METAL REMOVAL PROJECT ARE PROVIDING SAFE, COST-EFFECTIVE REMEDIATION OF CONTAMINATED SCRAP YARDS

    International Nuclear Information System (INIS)

    Watson, Dan; Eyman, Jeff

    2003-01-01

    Between 1974 and 1983, contaminated equipment was removed from the Paducah Gaseous Diffusion Plant (PGDP) process buildings as part of an enrichment process upgrade program. The upgrades consisted of the dismantlement, removal, and on-site storage of contaminated equipment, cell components, and scrap material (e.g., metal) from the cascade facilities. Scrap metal including other materials (e.g., drums, obsolete equipment) not related to this upgrade program have thus far accumulated in nine contiguous radiologically-contaminated and non-contaminated scrap yards covering 1.05E5 m2 (26 acres) located in the northwestern portion of the PGDP. This paper presents the sequencing of field operations and methods used to achieve the safe removal and disposition of over 47,000 tonnes (53,000 tons) of metal and miscellaneous items contained in these yards. The methods of accomplishment consist of mobilization, performing nuclear criticality safety evaluations, moving scrap metal to ground level, inspection and segregation, sampling and characterization, scrap metal sizing, packaging and disposal, and finally demobilization. Preventing the intermingling of characteristically hazardous and non-hazardous wastes promotes waste minimization, allowing for the metal and materials to be segregated into 13 separate waste streams. Low-tech solutions such as using heavy equipment to retrieve, size, and package scrap materials in conjunction with thorough planning that integrates safe work practices, commitment to teamwork, and incorporating lessons learned ensures that field operations will be conducted efficiently and safely

  2. Recycling of rare earth magnet scraps: Carbon and oxygen removal from Nd magnet scraps

    International Nuclear Information System (INIS)

    Saguchi, A.; Asabe, K.; Fukuda, T.; Takahashi, W.; Suzuki, R.O.

    2006-01-01

    The decarburization and deoxidation technique for permanent Nd-Fe-B magnet scrap is investigated. The carbon and oxygen contamination damage the magnetic properties. The carbon content decreased less than 0.001% by heating in air. The two stage deoxidation is applied, iron oxides are reduced by heating in hydrogen thereafter rare earth oxides are removed by Ca-reduction and leaching. The appropriate conditions for deoxidation in the Ca-reduction and suppressing the re-oxidation in the leaching are investigated. The heating pattern in Ca-reduction and the leaching condition for the mixture composed of Ca compounds and Nd-Fe-B alloy powder greatly affects the oxygen content of recycled material. The decarburized and deoxidized Nd-Fe-B magnet scrap can be recycled as alloying elements by melting

  3. HbD Punjab/HbQ India compound heterozygosity: An unusual association.

    Directory of Open Access Journals (Sweden)

    Stacy Colaco

    2014-11-01

    Full Text Available Background: Haemoglobinopathies are the commonest hereditary disorders in India and pose a major health problem. Both beta thalassaemia and structural haemoglobin variants are relatively common in north western India. Here we report a 29 year old Sindhi female who was referred to us for a haemoglobinopathy work up and genetic counseling since her spouse was a classical beta thalassaemia carrier. Method: A complete blood count was done on an automated cell counter. Haemoglobin analysis was carried out using HPLC Variant Haemoglobin Testing System.  The cellulose acetate electrophoresis was carried out [pH 8.9]. Confirmation of mutations was done by automated DNA sequencing. Results: HPLC analysis showed four major peaks, HbA0, a peak in the HbD window, an unknown peak [retention time 4.74 minutes] and a peak in the HbC window. The HbA2 level was 2.2% and the HbF level was 0.7%.Cellulose acetate electrophoresis at alkaline pH, a slow moving band was seen at the HbS/D position along with a prominent band at the HbA2 position. DNA sequencing of the β and α genes showed presence of the 2 hemoglobin variants :Hb D [b 121GAA à CAA] and Hb Q [a 64 AAG à GAG]. The δ globin gene was normal. The additional peak in the HbC window was due to the formation of a heterodimer hybrid. Conclusion: Both HbD Punjab and HbQ India are relatively common in India but their co-inheritance has not been described in the country. This is the second report of compound heterozygosity for HbQ India/HbD Punjab haemoglobinopathy globally, and the first one from India.

  4. Radiation protection aspects in importing metallic scraps

    International Nuclear Information System (INIS)

    Risica, S.; Di Ciaccio, P.

    1996-09-01

    The meeting deals with radiation protection problems caused by the possibility that radioactive metal scraps or radioactive sources hidden in the scraps, may arrive in a foundry. The importance of this issue and of rational and systematic solutions is showed by several accidents, happened in the past in numerous countries, by many signals in Italy and by some papers published in international scientific journals or reports issued by authorities and institutions in different countries

  5. The Properties of Red Blood Cells from Patients Heterozygous for HbS and HbC (HbSC Genotype

    Directory of Open Access Journals (Sweden)

    A. Hannemann

    2011-01-01

    Full Text Available Sickle cell disease (SCD is one of the commonest severe inherited disorders, but specific treatments are lacking and the pathophysiology remains unclear. Affected individuals account for well over 250,000 births yearly, mostly in the Tropics, the USA, and the Caribbean, also in Northern Europe as well. Incidence in the UK amounts to around 12–15,000 individuals and is increasing, with approximately 300 SCD babies born each year as well as with arrival of new immigrants. About two thirds of SCD patients are homozygous HbSS individuals. Patients heterozygous for HbS and HbC (HbSC constitute about a third of SCD cases, making this the second most common form of SCD, with approximately 80,000 births per year worldwide. Disease in these patients shows differences from that in homozygous HbSS individuals. Their red blood cells (RBCs, containing approximately equal amounts of HbS and HbC, are also likely to show differences in properties which may contribute to disease outcome. Nevertheless, little is known about the behaviour of RBCs from HbSC heterozygotes. This paper reviews what is known about SCD in HbSC individuals and will compare the properties of their RBCs with those from homozygous HbSS patients. Important areas of similarity and potential differences will be emphasised.

  6. 31P NMR spectroscopy and HbO2 cryospectrophotometry in prediction of tumor radioresistance caused by hypoxia.

    Science.gov (United States)

    Rofstad, E K; DeMuth, P; Fenton, B M; Ceckler, T L; Sutherland, R M

    1989-04-01

    The aim of this study was to search for possible relationships between the fraction of radiobiologically hypoxic cells in tumors and their 31P NMR spectral parameters and intracapillary HbO2 saturations. Four different tumor lines, two murine sarcomas (KHT, RIF-1) and two human ovarian carcinoma xenografts (MLS, OWI), were used. When tumor volume increased from about 200 mm3 to about 2000 mm3, hypoxic fraction increased from 12 to 23% for the KHT line, from 0.9 to 1.7% for the RIF-1 line, and from 9 to 28% for the MLS line. The OWI line showed similar hypoxic fractions at 200 (17%) and 2000 mm3 (15%). Tumor bioenergetic status decreased, that is, the inorganic phosphate (Pi) resonance increased and the phosphocreatine (PCr) and nucleoside triphosphate beta (NTP beta) resonances decreased, with increasing tumor volume for the KHT, RIF-1, and MLS lines, whereas the OWI line did not show any changes in the 31P NMR spectral parameters during tumor growth. Similarly, tumor HbO2 saturation status, that is, the fraction of vessels with HbO2 saturation above 30%, decreased with increasing tumor volume for the KHT, RIF-1, and MLS lines, but remained unchanged during tumor growth for the OWI line. Although the data indicated a relationship between hypoxic fraction and tumor bioenergetic status as well as tumor HbO2 saturation status within a specific line during tumor growth, there was no correlation between hypoxic fraction and tumor bioenergetic status or tumor HbO2 saturation status across the four tumor lines. This may have occurred because cell survival time under hypoxic stress as well as fraction of non-clonogenic, but metabolically active hypoxic cells differed among the tumor lines. This indicates that 31P NMR spectroscopy and HbO2 cryospectrophotometry data have to be supplemented with other data to be useful in prediction of tumor radioresistance caused by hypoxia.

  7. Stability study for magnetic reagent assaying Hb and HbA1c

    International Nuclear Information System (INIS)

    Hsieh, Wen-Pin; Chieh, J.J.; Yang, C.C.; Yang, S.Y.; Chen, Po-Yu; Huang, Yu-Hao; Hong, Y.W.; Horng, H.E.

    2013-01-01

    Reagents for magnetically labeled immunoassay on human Hb and human HbA1c have been synthesized. The reagents consist of Fe 3 O 4 magnetic particles biofunctionalized with antibodies against Hb and HbA1c. It has been demonstrated that the reagents can be applied to quantitatively detect Hb and HbA1c by using immunomagnetic reduction assay. In addition to characterizing the assay properties, such as the standard curve and the low-detection limit, the stability of reagents is investigated. To do this, the temporal dependence of particle sizes and the bio-activity of reagents are monitored. The results show that the reagents are highly stable when stored at 2–8 °C. This means that the reagents synthesized in this work are promising for practical applications. - Highlights: ► The properties of assaying Hb and HbA1c using immunomagnetic reduction are studied. ► The magnetic nanoparticles with antibodies are highly stable in solutions. ► No significant mutual interference between Hb and HbA1c in assays is observed. ► High-sensitivity assays on Hb and HbA1c using immunomagnetic reduction are achieved.

  8. Recovery of the secondary raw materials, recycling

    International Nuclear Information System (INIS)

    Chmielewska, E.

    2010-01-01

    In this chapter the recovery and recycling of secondary raw materials is explained. This chapter consists of the following parts: Paper and tetrapaks; Car wrecks; Scrap metal; Plastics; Used tires; Electrical and electronic equipment; Glass; Accumulators and batteries; Spent oil; Low-and non-waste technology.

  9. Stability study for magnetic reagent assaying Hb and HbA1c

    Energy Technology Data Exchange (ETDEWEB)

    Hsieh, Wen-Pin [Actherm Inc., Hsinchu 200, Taiwan (China); Chieh, J.J.; Yang, C.C. [Institute of Electro-optical Science and Technology, National Taiwan Normal University, Taipei 116, Taiwan (China); Yang, S.Y. [Institute of Electro-optical Science and Technology, National Taiwan Normal University, Taipei 116, Taiwan (China); MagQu Co., Ltd., Sindian Dist., New Taipei City 231, Taiwan (China); Chen, Po-Yu; Huang, Yu-Hao [Actherm Inc., Hsinchu 200, Taiwan (China); Hong, Y.W. [Institute of Electro-optical Science and Technology, National Taiwan Normal University, Taipei 116, Taiwan (China); Horng, H.E., E-mail: phyfv001@ntnu.edu.tw [Institute of Electro-optical Science and Technology, National Taiwan Normal University, Taipei 116, Taiwan (China)

    2013-01-15

    Reagents for magnetically labeled immunoassay on human Hb and human HbA1c have been synthesized. The reagents consist of Fe{sub 3}O{sub 4} magnetic particles biofunctionalized with antibodies against Hb and HbA1c. It has been demonstrated that the reagents can be applied to quantitatively detect Hb and HbA1c by using immunomagnetic reduction assay. In addition to characterizing the assay properties, such as the standard curve and the low-detection limit, the stability of reagents is investigated. To do this, the temporal dependence of particle sizes and the bio-activity of reagents are monitored. The results show that the reagents are highly stable when stored at 2-8 Degree-Sign C. This means that the reagents synthesized in this work are promising for practical applications. - Highlights: Black-Right-Pointing-Pointer The properties of assaying Hb and HbA1c using immunomagnetic reduction are studied. Black-Right-Pointing-Pointer The magnetic nanoparticles with antibodies are highly stable in solutions. Black-Right-Pointing-Pointer No significant mutual interference between Hb and HbA1c in assays is observed. Black-Right-Pointing-Pointer High-sensitivity assays on Hb and HbA1c using immunomagnetic reduction are achieved.

  10. Survey on the scrap iron and steel recycling in Thailand and Indonesia; Hatten tojokoku (Tai Indonesia) ni okeru tetsu scrap saiseiyo ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report describes the survey results of the scrap iron and steel recycling industries in Thailand and Indonesia. The purpose of this survey is to extract problems obstructing the scrap iron and steel recycling, to recognize the present situation and predict the future situation, and to examine the possibility of international cooperation. As a result of the survey, it was found that the quality of scrap collected in the domestic market is poor as it contains too many impurities for it to be utilized for the manufacture of many higher quality iron and steel products. The actual quantity of domestically collected scrap is too low to support the expected growth in demand in each nation. Current environmental management practices are largely concerned with the construction of wastewater treatment facilities and the extraction of furnace dust. However, the lack of enforcement of environmental regulations does not encourage companies to implement sound environmental practices. Neither government actively promotes and investigates iron and steel recycling in the domestic, commercial or industrial sectors. Collaboration with overseas nations having more advanced iron and steel industries could be helpful to the scrap recycling industry in both nations. 6 figs., 21 tabs.

  11. Diagnosis of Compound Heterozygous Hb Tak/β-Thalassemia and HbD-Punjab/β-Thalassemia by HbA2 Levels on Capillary Electrophoresis.

    Science.gov (United States)

    Panyasai, Sitthichai; Sakkhachornphop, Supachai; Pornprasert, Sakorn

    2018-01-01

    A misdiagnosis of β-thalassemia carrier in samples with Hb Tak and HbD-Punjab, the β-variants, can be a cause of inappropriate genetic counseling thus having a new case of β-thalassemia major. A capillary electrophoresis (CE) is very efficient in separating and quantifying HbA 2 . In this study, HbA 2 levels of samples which were doubted for compound heterozygous Hb Tak/β-thalassemia or heterozygous HbD-Punjab/β-thalassemia were measured and compared between CE and high performance liquid chromatography (HPLC). The molecular confirmation for Hb Tak, HbD-Punjab and β-thalassemia codons 17 (A > T), 41/42 (-TCTT), 71/72 (+A) and IVSI-nt1 (G > T) mutations and 3.4 kb deletion were also performed. Based on DNA analysis, 3 cases were diagnosed as compound heterozygous Hb Tak/β-thalassemia and one for HbD-Punjab/β-thalassemia. The elevated HbA 2 levels were found in all 4 samples with rages of 4.6-7.3% on CE while those were not found on HPLC. Thus, the elevated HbA 2 measured by CE can be used as a screening parameter for differentiating the homozygote of Hb Tak and HbD-Punjab from the compound heterozygote of these hemoglobinopathies and β-thalassemia.

  12. Scrapping of student bursaries confirmed.

    Science.gov (United States)

    Longhurst, Chris

    2016-07-27

    Student bursaries for nurses will be scrapped from next year, the government has confirmed. Undergraduate nursing and midwifery students in England will now face tuition fees and student loans from August 2017.

  13. System for Prevention, Detection and Response to Radioactive Materials in Scrap Metal in Ukraine

    Energy Technology Data Exchange (ETDEWEB)

    Makarovska, O., E-mail: makarovska@hq.snrc.gov.ua [State Nuclear Regulatory Committee of Ukraine, Kiev (Ukraine)

    2011-07-15

    The State control system to prevent, detect and respond to cases of radioactive material in scrap metal is functioning in Ukraine. The system includes regulations for the safe and secure management of metal scrap and administrative and technical measures to prevent, detect and respond to cases of radioactive material in scrap metal. The key elements of prevention are the system of licensing and supervision in the sphere of radioactive material use and the State system for inventory, registration and control of radiation sources. Metal scrap management is licensed by the Ministry of Industrial Policy and one of the licence conditions is radiation control of the scrap metal. State supervision of the operations with metal scrap is provided by Ministry of Health and Ministry of Environmental Protection according to the regulation 'State sanitary-ecological standard for metal scrap management'. Specific standards exist for the export of metal scrap. Export consignments are followed by a certificate that proves the radiological safety of the metal. Ukrainian metallurgical plants provide an input radiation control of metal scrap and an output control of the produced metal. Thus, there exists a five barrier system of metal scrap control: border control; exclusion zone perimeter control; metal scrap dealers control; metallurgical plants (input control and output control of produced metal); and export consignments radiological certification. To regain control over orphan sources (including occasional radioactive material in the scrap metal) the 'procedure for interaction of executive authorities and involved legal entities in case of revealing of radiation sources in no legal use' was approved by a Resolution of the Cabinet of Ministers of Ukraine. The investigation of each case with feedback, information of involved bodies, safe and secure storage of restored radioactive material are provided according to this procedure. (author)

  14. 26 CFR 7.57(d)-1 - Election with respect to straight line recovery of intangibles.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 14 2010-04-01 2010-04-01 false Election with respect to straight line recovery... ACT OF 1976 § 7.57(d)-1 Election with respect to straight line recovery of intangibles. (a) Purpose... Tax Reform Act of 1976. Under this election taxpayers may use cost depletion to compute straight line...

  15. Electrochemical sensor based on magnetic molecularly imprinted nanoparticles modified magnetic electrode for determination of Hb.

    Science.gov (United States)

    Sun, Binghua; Ni, Xinjiong; Cao, Yuhua; Cao, Guangqun

    2017-05-15

    A fast and selective electrochemical sensor for determination of hemoglobin (Hb) was developed based on magnetic molecularly imprinted nanoparticles modified on the magnetic glassy carbon electrode. The nanoparticles Fe 3 O 4 @SiO 2 with a magnetic core and a molecularly imprinted shell had regular structures and good monodispersity. Hb could be determined directly by electrochemical oxidization with the modified electrode. A magnetic field increased electrochemical response to Hb by two times. Imprinting Hb on the surface of Fe 3 O 4 @SiO 2 shortened the response time within 7min. Under optimum conditions, the imprinting factor toward the non-imprinted sensor was 2.8, and the separation factor of Hb to horseradish peroxidase was 2.6. The oxidation peak current had a linear relationship with Hb concentration ranged from 0.005mg/ml to 0.1mg/ml with a detection limit (S/N =3) of 0.0010mg/ml. The sensors were successfully applied to analysis of Hb in whole blood samples with recoveries between 95.7% and 105%. Copyright © 2016 Elsevier B.V. All rights reserved.

  16. 40 CFR 63.10885 - What are my management practices for metallic scrap and mercury switches?

    Science.gov (United States)

    2010-07-01

    ... minimize the presence of mercury in scrap from end-of-life vehicles. (3) Option for specialty metal scrap... metallic scrap and mercury switches? 63.10885 Section 63.10885 Protection of Environment ENVIRONMENTAL... Affected Sources § 63.10885 What are my management practices for metallic scrap and mercury switches? (a...

  17. Recycled scrap metal and soils/debris with low radioactive contents

    International Nuclear Information System (INIS)

    Carriker, A.W.

    1996-01-01

    Two types of large volume bulk shipments of materials with low radioactivity have characteristics that complicate compliance with normal transport regulations. Scrap metal for recycling sometimes contains radioactive material that was not known or identified by the shipper prior to it being offered for transport to a scrap recycle processor. If the radioactive material is not detected before the scrap is processed, radiological and economic problems may occur. If detected before processing, the scrap metal will often be returned to the shipper. Uranium mill-tailings and contaminated soils and debris have created potential public health problems that required the movement of large volumes of bulk material to isolated safe locations. Similarly, old radium processing sites have created contamination problems needing remediation. The US Department of Transportation has issued exemptions to shippers and carriers for returning rejected scrap metal to original shippers. Other exemptions simplify transport of mill-tailings and debris from sites being remediated. These exemptions provide relief from detailed radioassay of the radioactive content in each conveyance as well as relief from the normal requirements for packaging, shipping documents, marking, labelling, and placarding which would be required for some of the shipments if the exemptions were not issued. (Author)

  18. Evaluation of segmented gamma scanner measurements on cans of recoverable scrap

    International Nuclear Information System (INIS)

    Shull, A.H.; Weber, J.H.; MacMurdo, K.W.; Baker, L.B.

    1991-01-01

    Savannah River Site (SRS) has had a long-standing concern about the inability to measure recoverable scrap. A segmented gamma scanner (SGS) was evaluated for use in measuring cans of scrap materials. Four scrap cans were selected and re-packaged into containers that could be measured using calorimetry and gamma spectrometry. These scrap cans were later used as working standards for the SGS. In addition, replicate measurements were made on all cans of scrap currently stored with estimated values. Before accepting the SGS measurements on the cans, data from the replicate measurements of the standards and a limited number of process cans were analyzed to determine if there was a significant bias between the SGS and the calorimeter-gamma spectrometer measurements, if the random replication error would be acceptable for accountability, to set control limits for the workings standards, and to determine acceptable differences between replicate measurements. After completing the measurement of all process scrap cans in the inventory, the the final data were analyzed and estimates based on the two sets of data compared. The methodology used to determine the appropriate measurement error model, to estimate the measurement errors, to set control limits, and to determine the significance of the bias will be described as well as a comparison of the error estimates based on the preliminary versus final data

  19. Cation Homeostasis in Red Cells From Patients With Sickle Cell Disease Heterologous for HbS and HbC (HbSC Genotype

    Directory of Open Access Journals (Sweden)

    A. Hannemann

    2015-11-01

    Full Text Available Sickle cell disease (SCD in patients of HbSC genotype is considered similar, albeit milder, to that in homozygous HbSS individuals — but with little justification. In SCD, elevated red cell cation permeability is critical as increased solute loss causes dehydration and encourages sickling. Recently, we showed that the KCl cotransporter (KCC activity in red cells from HbSC patients correlated significantly with disease severity, but that in HbSS patients did not. Two transporters involved in red cell dehydration, the conductive channels Psickle and the Gardos channel, behaved similarly in red cells from the two genotypes, but were significantly less active in HbSC patients. By contrast, KCC activity was quantitatively greater in HbSC red cells. Results suggest that KCC is likely to have greater involvement in red cell dehydration in HbSC patients, which could explain its association with disease severity in this genotype. This work supports the hypothesis that SCD in HbSC patients is a distinct disease entity to that in HbSS patients. Results suggest the possibility of designing specific treatments of particular benefit to HbSC patients and a rationale for the development of prognostic markers, to inform early treatment of children likely to develop more severe complications of the disease.

  20. Management of radiation protection aspects in the recycling of metallurgical scrap: the report of UNECE team of specialists on radioactive contaminated scrap

    International Nuclear Information System (INIS)

    Deckers, B.

    2001-01-01

    Complete text of publication follows: In 1999, the United Nations Economic Commission for Europe (UNECE) has created a Team of Specialists on Radioactive Contaminated Metal Scrap: technically qualified representatives of the steel industry, government representatives and competent international organizations representatives have studied the problem of radioactively contaminated scrap and steel, and have proposed solutions in this context acceptable at the international level in order to harmonize the legislation, the systems of measurement of radioactivity, the levels of detection. This team has established a document which will be published by the United Nations, and where good practices on managing radioactive metal scrap are presented, and which also contains numerous recommendations in order to harmonize legislations. The paper presents the content of the document and the main recommendations of the team. (author)

  1. Enhanced high-solids anaerobic digestion of waste activated sludge by the addition of scrap iron.

    Science.gov (United States)

    Zhang, Yaobin; Feng, Yinghong; Yu, Qilin; Xu, Zibin; Quan, Xie

    2014-05-01

    Anaerobic digestion of waste activated sludge usually requires pretreatment procedure to improve the bioavailability of sludge, which involves considerable energy and high expenditures. This study proposes a cost-effective method for enhanced anaerobic digestion of sludge without a pretreatment by directly adding iron into the digester. The results showed that addition of Fe(0) powder could enhance 14.46% methane yield, and Fe scrap (clean scrap) could further enhance methane yield (improving rate 21.28%) because the scrap has better mass transfer efficiency with sludge and liquid than Fe(0) powder. The scrap of Fe with rust (rusty scrap) could induce microbial Fe(III) reduction, which resulted in achieving the highest methane yield (improving rate 29.51%), and the reduction rate of volatile suspended solids (VSS) was also highest (48.27%) among Fe powder, clean scrap and rusty scrap. PCR-DGGE proved that the addition of rusty scrap could enhance diversity of acetobacteria and enrich iron-reducing bacteria to enhance degradation of complex substrates. Copyright © 2014 Elsevier Ltd. All rights reserved.

  2. 46 CFR Sec. 12 - Disposition of removed equipment and scrap.

    Science.gov (United States)

    2010-10-01

    ... 46 Shipping 8 2010-10-01 2010-10-01 false Disposition of removed equipment and scrap. Sec. 12... CONTRACT-NSA-LUMPSUMREP Sec. 12 Disposition of removed equipment and scrap. (a) Article 8 of the NSA-LUMPSUMREP Contract provides that any ship equipment, fuel, lube oil, supplies, stores, furniture, fixtures...

  3. Hb variants in Korea: effect on HbA1c using five routine methods.

    Science.gov (United States)

    Yun, Yeo-Min; Ji, Misuk; Ko, Dae-Hyun; Chun, Sail; Kwon, Gye Cheol; Lee, Kyunghoon; Song, Sang Hoon; Seong, Moon Woo; Park, Sung Sup; Song, Junghan

    2017-07-26

    Quantification of glycated hemoglobin (HbA1c) is a challenge in patients with hemoglobin (Hb) variants. We evaluated the impact of various Hb variants on five routine HbA1c assays by comparing with the IFCC reference measurement procedure (RMP). Whole blood samples showing warning flags or no results on routine HPLC HbA1c assays were confirmed for Hb variants and were submitted to HbA1c quantification using Sebia Capillarys 2 Flex Piercing, Roche Tina-quant HbA1c Gen. 2, Bio-Rad Variant II Turbo 2.0, ADAMS HA-8180, Tosoh G8 standard mode, and IFCC RMP using LC-MS. Among 114 samples, the most common variants were Hb G-Coushatta (n=47), Queens (n=41), Ube-4 (n=11), Chad (n=4), Yamagata (n=4), G-His-Tsou (n=2), G-Taipei (n=1), Fort de France (n=1), Hoshida (n=1), and two novel variants (Hb α-globin, HBA 52 Gly>Cys and Hb β-globin, HBB 146 His>Asn). In terms of control samples, all the result of HbA1c were "acceptable", within the criteria of ±7% compared to IFCC RMP target values. However, percentage of "unacceptable" results of samples with Hb variants were 16% for Capillarys 2, 7% for Tina-quant, 51% for Variant II Turbo 2.0, 95% for G8 standard mode, and 89% for HA-8180. The Capillarys 2 and HA-8180 assay did not provide the results in 5 and 40 samples with Hb variants, respectively. HbA1c results from five routine assays in patients with relatively common Hb variants in Korea showed various degrees of bias compared to those of IFCC RMP. Therefore, laboratories should be aware of the limitation of their methods with respect to interference from Hb variants found commonly in their local population and suggest an alternative HbA1c quantification method.

  4. High Purity Tungsten Spherical Particle Preparation From WC-Co Spent Hard Scrap

    Directory of Open Access Journals (Sweden)

    Han Chulwoong

    2015-06-01

    Full Text Available Tungsten carbide-cobalt hard metal scrap was recycled to obtain high purity spherical tungsten powder by a combined hydrometallurgy and physical metallurgy pathway. Selective leaching of tungsten element from hard metal scrap occurs at solid / liquid interface and therefore enlargement of effective surface area is advantageous. Linear oxidation behavior of Tungsten carbide-cobalt and the oxidized scrap is friable to be pulverized by milling process. In this regard, isothermally oxidized Tungsten carbide-cobalt hard metal scrap was mechanically broken into particles and then tungsten trioxide particle was recovered by hydrometallurgical method. Recovered tungsten trioxide was reduced to tungsten particle in a hydrogen environment. After that, tungsten particle was melted and solidified to make a spherical one by RF (Ratio Frequency thermal plasma process. Well spherical tungsten micro-particle was successfully obtained from spent scrap. In addition to the morphological change, thermal plasma process showed an advantage for the purification of feedstock particle.

  5. Primary Raw Materials for Steelmakers: Scrap and Pig Iron

    Directory of Open Access Journals (Sweden)

    Cristina Bumbac

    2011-10-01

    Full Text Available Most of the daily steel we so much need is obtained now in electric furnaces, for which the main raw material is scrap. The scrap market is a very sensitive one, depending very much on internal collect, exports and imports, the market of steel and freight. Commerce with scrap is one of the most intense among all the countries of the world and covers all the routes and regions. Every ten years or so importers become exporters and vice versa, due to the period of life of the metallic products. For example, China was for the last 10 years one of the biggest importers (after Turkey, which is number one in importers' hierarchy, but prognoses tell that in 2-3 years China might become self-sufficient due to the investments which began some 20 years ago. USA was one of the largest exporters, but some 3 years ago some analysts advanced the idea that it may become a net importer (it didn't happened, though. The scrap market is not only important, it is also very interesting, with twisted evolutions and volatile prices in some periods.

  6. Aqueous Nitrate Recovery Line at Los Alamos National Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Finstad, Casey Charles [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-06-15

    This powerpoint is part of the ADPSM Plutonium Engineering Lecture Series, which is an opportunity for new hires at LANL to get an overview of work done at TA55. It goes into detail about the aqueous nitrate recovery line at Los Alamos National Laboratory.

  7. Actinide recovery from waste and low-grade sources

    International Nuclear Information System (INIS)

    Navratil, J.D.; Schulz, W.W.

    1982-01-01

    Actinide and nuclear fuel cycle operations generate a variety of process waste streams. New methods are needed to remove and recover actinides. More interest is also being expressed in recovering uranium from oceans, phosphoric acid, and other low grade sources. To meet the need for an up-to-date status report in the area of actinide recovery from waste and low grade sources, these papers were brought together. The papers provide an authoritative, in-depth coverage of an important area of nuclear and industrial and engineering chemistry which cover the following topics: uranium recovery from oceans and phosphoric acid; recovery of actinides from solids and liquid wastes; plutonium scrap recovery technology; and other new developments in actinide recovery processes

  8. High Value Scrap Tire Recycle

    Energy Technology Data Exchange (ETDEWEB)

    Bauman, B. D.

    2003-02-01

    The objectives of this project were to further develop and scale-up a novel technology for reuse of scrap tire rubber, to identify and develop end uses for the technology (products), and to characterize the technology's energy savings and environmental impact.

  9. Management of radioactive scrap metal at SCK-CEN

    International Nuclear Information System (INIS)

    Noynaert, L.; Klein, M.; Cornelissen, R.; Ponnet, M.

    2000-01-01

    The environmental concern and public perception as well as the steadily increase of the conditioning and disposal costs are pushing the nuclear sector to minimise the amount of radioactive waste. Hence it is a strong incentive to prefer the management option 'recycling and reuse' instead of the option 'disposal and replacement'. The 'recycling and reuse' option requires the availability of decontamination techniques as well as measuring techniques allowing to prove that the release criteria are met. Therefore SCK-CEN has now two decontamination installations for scrap metal on its own site. One installation uses a wet abrasive technique while the other one uses a chemical process based on the Ce 4+ . These two installations, combined with the use of foundries for free release or for radioactive scrap metal recycling are now common practices at SCK-CEN and will allow to reduce the metallic waste to 10% of the metallic scrap production and the costs at least by a factor 2.5. (author)

  10. Complex deformation routes for direct recycling aluminium alloy scrap via industrial hot extrusion

    Science.gov (United States)

    Paraskevas, Dimos; Kellens, Karel; Kampen, Carlos; Mohammadi, Amirahmad; Duflou, Joost R.

    2018-05-01

    This paper presents the final results of an industrial project, aiming for direct hot extrusion of wrought aluminium alloy scrap at an industrial scale. Two types of complex deformation/extrusion routes were tested for the production of the same profile, starting from AA6060 scrap in form of machining chips. More specifically scrap-based billets were extruded through: a 2-porthole and a 4-porthole die-set, modified for enhanced scrap consolidation and grain refinement. For comparison reasons, cast billets of the same alloy were extruded through the modified 2-porthole die set. The tensile testing results as well as microstructural investigations show that the 4-porthole extrusion route further improves scrap consolidation compared to the 2-porthole die output. The successful implementation of solid state recycling, directly at industrial level, indicates the technological readiness level of this research.

  11. A study of liberation and separation process of metals from printed circuit boards (PCBs) scrap

    International Nuclear Information System (INIS)

    Noorliyana, H.A.; Zaheruddin, K.; Mohd Fazlul Bari; M. Sri Asliza; Nurhidayah, A.Z.; Kamarudin, H.

    2009-01-01

    Since the metallic elements are covered with or encapsulated by various plastic or ceramic materials on printed circuit boards, a mechanical pre-treatment process allowing their liberation and separation is first needed in order to facilitate their efficient extraction with hydrometallurgy route. Even though many studies have been performed on the mechanical pre-treatment processing for the liberation and separation of the metallic components of printed circuit boards scrap, further studies are required to pave the way for efficient recycling of waste printed circuit boards through a combination of mechanical pre-treatment and hydrometallurgical technology. In this work, a fundamental study has been carried out on the mechanical pre-treatment that is necessary to recover metallic concentrates from printed circuit boards scraps. The most important problem is to separate or release particles from the associated gangue minerals at the possible liberation particle size. The distribution of metallic elements has been also investigated in relation to the particle size of the milled printed circuit boards. The samples of printed circuit boards were separated into the magnetic and non-magnetic fractions by Rare-earth Roll Magnetic separator. Thereafter, the magnetic and non-magnetic fractions were separated to heavy fraction (metallic elements) and light fraction (plastic) by Mozley Laboratory Table Separator. The recovery ratios and the evaluation of the metallic concentrates recovered by each separation process were also investigated. This study is expected to provide useful data for the efficient mechanical separation of metallic components from printed circuit boards scraps. (author)

  12. Hb Melusine and Hb Athens-Georgia: potentially underreported in the Belgian population? Four cases demonstrating the lack of detection using common CE-HPLC methods either for glycated hemoglobin (HbA1C) analysis or Hb variant screening.

    Science.gov (United States)

    Peeters, Bart; Brandt, Inger; Desmet, Koenraad; Harteveld, Cornelis L; Kieffer, Davy

    2016-12-01

    Suspected hemoglobin (Hb) variants, detected during HbA 1C measurements should be further investigated, determining the extent of the interference with each method. This is the first report of Hb Melusine and Hb Athens-Georgia in Caucasian Belgian patients. Intervention & Technique: Since common CE-HPLC methods for HbA 1C analysis or Hb variant screening are apparently unable to detect these Hb variants, their presence might be underestimated. HbA 1C analysis using CZE, however, alerted for their presence. Moreover, in case of Hb Melusine, even Hb variant screening using CZE was unsuccessful in its detection. Fortunately, carriage of Hb Melusine or Hb Athens-Georgia variants has no clinical implications and, as shown in this report, no apparent difference in HbA 1C should be expected.

  13. Optimal Recycling of Steel Scrap and Alloying Elements: Input-Output based Linear Programming Method with Its Application to End-of-Life Vehicles in Japan.

    Science.gov (United States)

    Ohno, Hajime; Matsubae, Kazuyo; Nakajima, Kenichi; Kondo, Yasushi; Nakamura, Shinichiro; Fukushima, Yasuhiro; Nagasaka, Tetsuya

    2017-11-21

    Importance of end-of-life vehicles (ELVs) as an urban mine is expected to grow, as more people in developing countries are experiencing increased standards of living, while the automobiles are increasingly made using high-quality materials to meet stricter environmental and safety requirements. While most materials in ELVs, particularly steel, have been recycled at high rates, quality issues have not been adequately addressed due to the complex use of automobile materials, leading to considerable losses of valuable alloying elements. This study highlights the maximal potential of quality-oriented recycling of ELV steel, by exploring the utilization methods of scrap, sorted by parts, to produce electric-arc-furnace-based crude alloy steel with minimal losses of alloying elements. Using linear programming on the case of Japanese economy in 2005, we found that adoption of parts-based scrap sorting could result in the recovery of around 94-98% of the alloying elements occurring in parts scrap (manganese, chromium, nickel, and molybdenum), which may replace 10% of the virgin sources in electric arc furnace-based crude alloy steel production.

  14. Transcriptional regulation of Hb-α and Hb-β through nuclear factor E2-related factor-2 (Nrf2) activation in human vaginal cells: A novel mechanism of cellular adaptability to oxidative stress.

    Science.gov (United States)

    Saha, Debarchana; Koli, Swanand; Reddy, Kudumula Venkata Rami

    2017-06-01

    Hemoglobin (Hb), a major protein involved in transport of oxygen (O 2 ), is expressed by erythroid lineages. Until recently, it was not known whether non-erythroid cells express Hb. The objective was to evaluate the expression and functional significance of Hb-α and Hb-β in human primary vaginal epithelial cells (hPVECs) and decipher downstream signaling. RT-PCR, qRT-PCR, flow cytometry, Western blot, immunofluorescence were used to evaluate the expression of Hb-α, Hb-β, and nuclear factor E2-related factor-2(Nrf2) after hydrogen peroxide (H 2 O 2 ) induction. Electrophoretic mobility shift assay (EMSA) and chromatin immunoprecipitation (ChIP) assay were used to determine the binding efficiency of Nrf2 on the Hb-α promoter. Stimulation of hPVECs and human vaginal epithelial cell line, VK2/E6E7 with H 2 O 2 augmented the expression of Hb-α, Hb-β, Nrf2, heme oxygenase-1 (HO-1), and reactive oxygen species (ROS). Treatment of these cells with Nrf2 inhibitor, trigonelline (Trig) inhibited Hb-α and Hb-β expressions. Hb-α and Hb-β overexpression downregulated H 2 O 2 -induced ROS. The presence of Nrf2 binding domain was demonstrated within Hb-α promoter. The results revealed for the first time that Hb-α and Hb-β were induced by oxidative stress through the activation of Nrf2. Overexpression of Hb-α and Hb-β ameliorated H 2 O 2 -induced oxidative stress, indicating one of the possible mechanism(s) to protect hPVECS from oxidative stress. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  15. Gold and palladium adsorption from leached electronic scrap using ordered mesoporous carbon nanoscaffolds

    Energy Technology Data Exchange (ETDEWEB)

    McDowell, Rocklan; Dutech, Guy

    2014-09-01

    Ordered mesoporous carbon (OMC) nanoscaffolds are engineered agglomerates of carbon nanotubes held together by small carbon nanofibers with uniform pore sizes, high pore volume, and high channel permeability. These materials exhibit very high affinity for the adsorption of gold from aqueous acidic mixtures. The efficiency of gold recovery is comparable to those typically accomplished using biopolymer-based adsorbents. The adsorption efficiency for other precious metals such as palladium and platinum is lower. Studies on the precious metal (Au, Pd) adsorption on OMC materials from actual liquors of leached electronics will be presented. Adsorption properties will be compared for several different sorbents used for the recovery of precious metals. The leach liquor compositions for three different types of electronic scrap materials (personal computer board, cell phone and tv input/output board) will be presented. The sorption efficiencies for Au, Pd, together with a spectrum of competing and non-competing metals, from such leach mixtures will be compared.

  16. Gold and palladium adsorption from leached electronic scrap using ordered mesoporous carbon nanoscaffolds

    International Nuclear Information System (INIS)

    McDowell, Rocklan; Dutech, Guy

    2014-01-01

    Ordered mesoporous carbon (OMC) nanoscaffolds are engineered agglomerates of carbon nanotubes held together by small carbon nanofibers with uniform pore sizes, high pore volume, and high channel permeability. These materials exhibit very high affinity for the adsorption of gold from aqueous acidic mixtures. The efficiency of gold recovery is comparable to those typically accomplished using biopolymer-based adsorbents. The adsorption efficiency for other precious metals such as palladium and platinum is lower. Studies on the precious metal (Au, Pd) adsorption on OMC materials from actual liquors of leached electronics will be presented. Adsorption properties will be compared for several different sorbents used for the recovery of precious metals. The leach liquor compositions for three different types of electronic scrap materials (personal computer board, cell phone and tv input/output board) will be presented. The sorption efficiencies for Au, Pd, together with a spectrum of competing and non-competing metals, from such leach mixtures will be compared.

  17. Economic aspects of recycling U.S. Department of Energy radioactive scrap metal

    International Nuclear Information System (INIS)

    Harrop, J.; Numark, N.; MacKinney, J.

    1995-01-01

    The U.S. Department of Energy (DOE) has substantial quantities of scrap metal contaminated with low-levels of radioactivity. What is more important, current DOE Decommissioning and Dismantlement (D and D) plans will generate even more radioactive scrap metal. Disposition of this radioactive scrap metal could result in substantial costs to the DOE, but if certain options are exercised, could result in an economic gain. This paper outlines five basic options the DOE could follow for disposition of its radioactive scrap metal, and then examines the economic consequences of each option. A cost-benefit analysis was used to evaluate each of the five options. Real costs, derived from DOE studies and private industry, formed the basis for all analysis. These include transportation, packaging, processing (melt-refining) prices charged by industry, and burial fees and scrap metal storage facility operating and surveillance costs faced by the DOE. Other potential costs, such as the avoided costs of mining, and other less-well defined factors are assumed imbedded in the prices charged by industry for processing radioactive scrap metal. The results of this analysis show that burial cost is the most significant factor to consider in deciding which RSM disposition option to pursue. Moderate variations in burial costs can dramatically change the outcome of the cost-benefit analysis. (author)

  18. Problems concerned with scrap metal monitoring at borders

    International Nuclear Information System (INIS)

    Duftschmid, K.E.

    1997-01-01

    Since the early 1980's numerous incidents have been reported in which radioactive material or empty labelled containers for radioactive sources have been found in scrap metal. Apart from the potential health hazard to employees and the general public resulting costs for decontamination, shutdown of production and waste of products already amounted to multi-million dollar figures. Since the opening of the ''iron border'' in Europe, incidents of illicit trafficking of radioactive sources across borders and contamination of scrap metal imported from the former ''Eastern Countries'' have considerably increased, as a result of the lack of a suitable radiation protection infrastructure in some of these countries. This initiated monitoring of scrap metal transports at the borders of several European countries, such as Austria, Finland, Germany and Italy. Up to now neither universally accepted clearance levels for scrap contamination, nor an agreed standardised procedure for its control exist, although the IAEA as well as the European Commission have proposed some recommendations. As a pragmatic solution for border monitoring it is suggested to apply, as practical clearance level, a dose rate on the outside of the vehicle in the order of 0,1 μSv/h, which is approximately equivalent to double natural environmental background. This dose rate would correspond to an activity concentration for 60 Co in the order of 1 kBq/kg and therefore be in a tolerable range, even in view of products coming in close contact with the public. (author)

  19. Radioactive sources and contaminated materials in scrap: monitoring, detection and remedial actions

    International Nuclear Information System (INIS)

    Gallini, R.; Berna, V.; Bonora, A.; Santini, M.

    1999-01-01

    The scrap recycling in steel and other metal mills represents one of the most relevant activities in the Province of Brescia (Lombardy, Italy). In our Province more than 20 million tonnes of metal scrap are recycled every year by a melting process. Since 1990, many accidents which took place were caused by the unwanted melting of radioactive sources, that were probably hidden in metal scrap. In 1993, the Italian Government stated directives to monitor metal scrap imported from non-EC countries because of the suspicion of the illegal traffic of radioactive materials. In 1996, a law imposed the control of all metal scrap, regardless of their origins. Since 1993, our staff have controlled thousands of railway wagons and trucks. Approximately a hundred steel mills and foundries of aluminium, cooper, brass, etc. have also been controlled and many samples have been collected (flue dust, slag, finished products). During these controls, contaminated areas have been brought to light in two warehouses (Cs 137), in 6 companies (Cs 137 and Am 241), in two landfills of industrial waste (Cs 137) and in a quarry (Cs 137). Up to now the contaminated areas have been cleaned, except for the last one. About 150 radioactive sources on contaminated materials have been found in metal scrap. We found radioactive sources of Co 60, Ra 226, Ir 192, Kr 85, Am 241, while the contamination of metals was mainly due to Ra 226. The situation described above justifies an accurate control of the amount of scrap to reduce the risk of contamination of the workers in the working areas, in the environment and in the general public. (author)

  20. Detecting the presence of abnormal radioactivity in scrap using the statistical method

    International Nuclear Information System (INIS)

    Baillet, G.

    1999-01-01

    ' irrespective of the location of the check. It is true that there is a degree of regularity in the volume and tonnage of the lorries used for carrying scrap, but in view of the variety in the content and types of the scrap, a broader dispersion was expected. It was then possible to identify a warning threshold on the basis of the value of this ratio by using the classical rules of statistical process control: the threshold is equal to the mean increased by five standard deviations, corresponding to a generally accepted compromise between the rate of non-detection of an actual anomaly and the false alarm rate. This is the value which has been applied to all our steel plant sites, which all have the same checking equipment. Where different equipment is to be used, all that will be necessary will be to recalculate the mean and standard deviation during a prior observation exercise on a significant number of normal vehicles before pursuing the same line of reasoning. Indeed, this method is not restricted to scrap and may be applied wherever checking is carried out in relatively repetitive and reproducible conditions, especially where gantries are used. This method cannot be used to measure in becquerels the exogenous activity added to the load, still less to determine the nature of the radioelement present. In a particular configuration it simply allows us to say that beyond a warning threshold defined in this manner, there is a high probability that an anomaly is present: it will then be necessary to isolate the vehicle and undertake additional investigations using specialists and special equipment so that, taking all necessary precautions, the presence of hazardous products can be confirmed and appropriate steps taken. (author)

  1. Acute Sickle Hepatic Crisis after Liver Transplantation in a Patient with Hb SC Disease

    Directory of Open Access Journals (Sweden)

    J. H. Gillis

    2015-01-01

    Full Text Available Acute sickle hepatic crisis (ASHC has been observed in approximately 10% of patients with sickle cell disease. It occurs predominantly in patients with homozygous (Hb SS sickle cell anemia and to a lesser degree in patients with Hb SC disease, sickle cell trait, and Hb S beta thalassemia. Patients commonly present with jaundice, right upper quadrant pain, nausea, low-grade fever, tender hepatomegaly, and mild to moderate elevations in serum AST, ALT, and bilirubin. We describe the case of a patient with a history of hemoglobin SC disease and cirrhosis caused by hepatitis C presenting approximately 1 year after liver transplantation with an ASHC. The diagnosis was confirmed by liver biopsy. Our patient was treated with RBC exchange transfusions, IV hydration, and analgesia and made a complete recovery. Only a limited number of patients with sickle cell disease have received liver transplants, and, to our knowledge, this is the first case of ASHC after transplantation in a patient with Hb SC disease.

  2. Intracapillary HbO2 saturations in murine tumours and human tumour xenografts measured by cryospectrophotometry: relationship to tumour volume, tumour pH and fraction of radiobiologically hypoxic cells.

    Science.gov (United States)

    Rofstad, E K; Fenton, B M; Sutherland, R M

    1988-05-01

    Frequency distributions for intracapillary HbO2 saturation were determined for two murine tumour lines (KHT, RIF-1) and two human ovarian carcinoma xenograft lines (MLS, OWI) using a cryospectrophotometric method. The aim was to search for possible relationships between HbO2 saturation status and tumour volume, tumour pH and fraction of radiobiologically hypoxic cells. Tumour pH was measured by 31P NMR spectroscopy. Hypoxic fractions were determined from cell survival curves for tumours irradiated in vivo and assayed in vitro. Tumours in the volume range 100-4000 mm3 were studied and the majority of the vessels were found to have HbO2 saturations below 10%. The volume-dependence of the HbO2 frequency distributions differed significantly among the four tumour lines; HbO2 saturation status decreased with increasing tumour volume for the KHT, RIF-1 and MLS lines and was independent of tumour volume for the OWI line. The data indicated that the rate of decrease in HbO2 saturation status during tumour growth was related to the rate of development of necrosis. The volume-dependence of tumour pH was very similar to that of the HbO2 saturation status for all tumour lines. Significant correlations were therefore found between HbO2 saturation status and tumour pH, both within tumour lines and across the four tumour lines, reflecting that the volume-dependence of both parameters probably was a compulsory consequence of reduced oxygen supply conditions during tumour growth. Hypoxic fraction increased during tumour growth for the KHT, RIF-1 and MLS lines and was volume-independent for the OWI line, suggesting a relationship between HbO2 saturation status and hypoxic fraction within tumour lines. However, there was no correlation between these two parameters across the four tumour lines, indicating that the hypoxic fraction of a tumour is not determined only by the oxygen supply conditions; other parameters may also be important, e.g. oxygen diffusivity, rate of oxygen

  3. AIR EMISSIONS FROM SCRAP TIRE COMBUSTION

    Science.gov (United States)

    The report discusses air emissions from two types of scrap tire combustion: uncontrolled and controlled. Uncontrolled sources are open tire fires, which produce many unhealthful products of incomplete combustion and release them directly into the atmosphere. Controlled combustion...

  4. Feasibility study of a portable smelter for scrap metals

    International Nuclear Information System (INIS)

    Cavendish, J.H.

    1976-06-01

    The use of a portable smelter to process uranium-contaminated scrap metals was studied. Objectives were to convert scrap metal located at many diverse sites into a form which would be suitable for unlicensed sale and reduce the problems associated with storing the scrap. The Foundry Design Company study indicated the portable smelter concept was feasible from an equipment and transportation standpoint. Capital costs for a 5-ton/hour (steel) nominal capacity unit were estimated to be $2,349,000. Technical evaluation indicates that all the common metals considered, i.e., iron, nickel, copper, and aluminum, are amenable to uranium decontamination by smelting except aluminum. An economic evaluation of the processing of the 30,000 tons of steel scrap to be generated by the Cascade Improvement Program by a portable smelter was made based upon information supplied by Foundry Design Company, plus the assumption that the product metal could be sold for $120.00 per ton. This evaluation indicated a net return of $2,424,000 to the government could be realized. The Health and Safety study indicated no major problems of this nature would be encountered in operating a portable smelter. The legal review indicated the proposed operation fell within the authority of existing regulations. Consideration of possible conflicts with regard to competition with the private sector was suggested

  5. Scrap of gloveboxes No. 801-W and No. 802-W

    CERN Document Server

    Ohuchi, S; Kurosawa, M; Okane, S; Usui, T

    2002-01-01

    Both gloveboxes No. 801-W for measuring samples of uranium or plutonium and No. 802-W for analyzing the quantity of uranium or plutonium are established at twenty five years ago in the analyzing room No. 108 of Plutonium Fuel Research Facility. It was planned to scrap the gloveboxes and to establish new gloveboxes. This report describes the technical view of the scrapping works.

  6. Recycled tetrahedron-like CuCl from waste Cu scraps for lithium ion battery anode.

    Science.gov (United States)

    Hou, Hongying; Yao, Yuan; Liu, Song; Duan, Jixiang; Liao, Qishu; Yu, Chengyi; Li, Dongdong; Dai, Zhipeng

    2017-07-01

    The wide applications of metal Cu inevitably resulted in a large quantity of waste Cu materials. In order to recover the useful Cu under the mild conditions and reduce the environmental emission, waste Cu scraps were recycled in the form of CuCl powders with high economic value added (EVA) via the facile hydrothermal route. The recycled CuCl powders were characterized in terms of scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDX) and X-ray diffraction (XRD). The results suggested that the recycled CuCl powders consisted of many regular tetrahedron-like micro-particles. Furthermore, in order to reduce the cost of lithium ion battery (LIB) anode and build the connection of waste Cu scraps and LIB, the recycled CuCl powders were evaluated as the anode active material of LIB. As expected, the reversible discharge capacity was about 171.8mAh/g at 2.0C even after 50 cycles, implying the satisfactory cycle stability. Clearly, the satisfactory results may open a new avenue to develop the circular economy and the sustainable energy industry, which would be very important in terms of both the resource recovery and the environmental protection. Copyright © 2017. Published by Elsevier Ltd.

  7. Growth recovery lines are more common in infants at high vs. low risk for abuse

    International Nuclear Information System (INIS)

    Zapala, Matthew A.; Tsai, Andy; Kleinman, Paul K.

    2016-01-01

    Growth recovery lines, also known as growth arrest lines, are transverse radiodense metaphyseal bands that develop due to a temporary arrest of endochondral ossification caused by local or systemic insults. To determine if growth recovery lines are more common in infants at high risk versus low risk for abuse. Reports of American College of Radiology compliant skeletal surveys (1999-2013) were reviewed with clinical records. Infants at low risk for abuse had a skull fracture without significant intracranial injury, history of a fall and clinical determination of low risk (child protection team/social work assessment). Infants at high risk had significant intracranial injury, retinal hemorrhages, other skeletal injuries and clinical determination of high risk. There were 52 low-risk infants (mean: 4.7 months, range: 0.4-12 months) and 21 high-risk infants (mean: 4.2 months, range: 0.8-9.1 months). Two blinded radiologists independently evaluated the skeletal survey radiographs of the knees/lower legs for the presence of at least one growth recovery line. When growth recovery lines are scored as probably present or definitely present, their prevalence in the low-risk group was 38% (standard deviation [SD] = 8%; reader 1 = 17/52, reader 2 = 23/52) vs. 71% (SD = 7%; reader 1 = 16/21, reader 2 = 14/21) in the high-risk group (P < 0.001; odds ratio 4.0, 95% CI: 1.7-9.5). Growth recovery lines are encountered at a significantly higher rate in infants at high risk vs. low risk for abuse. This suggests that abused infants are prone to a temporary disturbance in endochondral ossification as a result of episodic physiological stresses. (orig.)

  8. Co-inheritance of α0 -thalassemia elevates Hb A2 level in homozygous Hb E: Diagnostic implications.

    Science.gov (United States)

    Singha, K; Srivorakun, H; Fucharoen, G; Fucharoen, S

    2017-10-01

    Differentiation of homozygous hemoglobin (Hb) E with and without α 0 -thalassemia is subtle on routine hematological ground. We examined in a large cohort of homozygous Hb E if the level of Hb A 2 is helpful. A total of 592 subjects with homozygous Hb E were recruited from ongoing thalassemia screening program. Additionally, five couples at risk of having fetuses with Hb Bart's hydrops fetalis who were homozygous Hb E were also investigated. Hb analysis was performed using capillary electrophoresis system. Globin genotypes were defined by DNA analysis. Subjects were classified into four groups including pure homozygous Hb E (n=532), homozygous Hb E/α 0 -thalassemia (n=48), Hb Constant Spring EE Bart's disease (n=8), and Hb EE Bart's disease (n=4). The levels of Hb A 2 were found, respectively, to be 4.97±0.69, 6.64±1.02, 4.86±0.87, and 7.60±1.04%. Among five couples at risk, α 0 -thalassemia was identified in three subjects with Hb A 2 >6.0%. Increased Hb A 2 level is a useful marker for differentiation of homozygous Hb E with and without α 0 -thalassemia. This should lead to a significant reduction in number of referral cases of homozygous Hb E for molecular testing of α 0 -thalassemia in routine practice. © 2017 John Wiley & Sons Ltd.

  9. Final Radiological Assessment of External Exposure for CLEAR-Line Americium Recovery Operations

    Energy Technology Data Exchange (ETDEWEB)

    Davis, Adam C. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Belooussova, Olga N. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Hetrick, Lucas Duane [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2014-11-12

    Los Alamos National Laboratory is currently planning to implement an americium recovery program. The americium, ordinarily isotopically pure 241Am, would be extracted from existing Pu materials, converted to an oxide and shipped to support fabrication of americium oxide-beryllium neutron sources. These operations would occur in the currently proposed Chloride Extraction and Actinide Recovery (CLEAR) line of glove boxes. This glove box line would be collocated with the currently-operational Experimental Chloride Extraction Line (EXCEL). The focus of this document is to provide an in-depth assessment of the currently planned radiation protection measures and to determine whether or not further design work is required to satisfy design-goal and ALARA requirements. Further, this document presents a history of americium recovery operations in the Department of Energy and high-level descriptions of the CLEAR line operations to provide a basis of comparison. Under the working assumptions adopted by this study, it was found that the evaluated design appears to mitigate doses to a level that satisfies the ALARA-in-design requirements of 10 CFR 835 as implemented by the Los Alamos National Laboratory procedure P121. The analyses indicate that extremity doses would also meet design requirements. Dose-rate calculations were performed using the radiation transport code MCNP5 and doses were estimated using a time-motion study developed in consort with the subject matter expert. A copy of this report and all supporting documentation are located on the Radiological Engineering server at Y:\\Rad Engineering\\2013 PROJECTS\\TA-55 Clear Line.

  10. Radioactivity in the scrap recycling process: Radiation protection aspects and experimental monitoring problems

    International Nuclear Information System (INIS)

    Sacco, D.; Ruggeri, F.; Bindi, G.; Bonanni, A.; Casciardi, S.; Delia, R.; Loppa, A.; Rossi, P.; Venturini, L.

    1996-01-01

    The steel scrap recycling by steel mill is increasing moved by profits and by purpose of protection of environmental resources. Besides the use of radioactive sources in several fields (medical, industrial and in scientific researches) on one hand, and the disposal of made radioactive materials from nuclear reactors on the other one, makes the likelihood no more negligible that some radionuclides could be found, accidental y or fraudulently, in steel recycling scrap. Radiation protection problems for surveillance both employees in the production cycle and of people and environment in general arose. First of all, we characterize different type of radioactive materials that can found in scraps, pointing out the potential hazards from exposure of workers and people and from environmental contamination, related to physical and chemical specifications of the involved radionuclides. Some suitable monitoring equipment for scrap recycling facilities are discussed, related to the different step of production cycle (transport, storage, manipulation and melting). At last experimental data, taken in some periods of the monitoring campaign made at the Italian border on imported scraps, are presented. (author)

  11. German experience in recycling of contaminated scrap by melting

    International Nuclear Information System (INIS)

    Quade, U.

    2003-01-01

    Recycling of radioactively contaminated scrap to products for further application in the nuclear cycle is Germany as an economic alternative. It has been shown that recycling within the nuclear industry reduces the collective dose as well as the number of individuals who receive doses. In the future when decommissioning of NPP will increase, a high amount of slightly radioactive steel scrap has to be managed safely. Recycling will play an important role to keep as much of these materials within the nuclear cycle as economically possible. Siempelkamp supplies a broad range of products made of recycled material from the nuclear industry. Containers made of nodular cast iron for transport and storage of radwaste as well as containers made of concrete with iron granules additive to increase the density up to 4 g/cm 3 , are offered. Interim and final disposal volume, having consequences on costs, can be reduced when recycling is applied for slightly contaminated metallic scrap

  12. Plutonium scrap processing at the Los Alamos Scientific Laboratory

    International Nuclear Information System (INIS)

    Nixon, A.E.; McKerley, B.J.; Christensen, E.L.

    1980-01-01

    The Los Alamos Scientific Laboratory currently has the newest plutonium handling facility in the nation. Los Alamos has been active in the processing of plutonium almost since the discovery of this man-made element in 1941. One of the functions of the new facility is the processing of plutonium scrap generated at LASL and other sites. The feed for the scrap processing program is extremely varied, and a wide variety of contaminants are often encountered. Depending upon the scrap matrix and contaminants present, the majority of material receives a nitric acid/hydrofluoric acid or nitric acid/calcium fluoride leach. The plutonium nitrate solutions are then loaded onto an anion exchange column charged with DOWEX 1 x 4, 50 to 100 mesh, nitrate form resin. The column is eluted with 0.48 M hydroxyl amine nitrate. The Pu(NO 3 ) 3 is then precipitated as plutonium III oxalate which is calcined at 450 to 500 0 C to yield a purified PuO 2 product

  13. Radioactive materials in scrap metal, the situation in Switzerland

    International Nuclear Information System (INIS)

    Jossen, H.

    2005-01-01

    About 10 years ago, different happenings in the Swiss and international metal scrap recycling scene created a sensibility to unwanted radioactive substances in scrap metal. Italy, one of the main buyers for scrap metals, started at its borders with systematic checks, arranged by authorities. As a consequence, in Switzerland a concept was elaborated under cooperation of the recycling companies, the Italian authorities, the Federal Office of Public Health (BAG), Swiss Federal Nuclear Safety Inspectorate (HSK) and the Swiss National Accident Insurance Fund (Suva) to fulfil the different requirements. Individual radioprotection, protection of environment, protection of work yard and machinery and the quality assurance of the recycled metals and the resulting products requires adapted solutions with the main issues: training, suitable measuring equipment and an intervention-and waste management. Detected radioactive substances are professionally recovered, stored and submitted to the radioactive waste collection. The investigation of the happenings can lead to useful hints on gaps and on chances for improvements in general radioprotection. (orig.)

  14. Diagnosis of a rare double heterozygous Hb D Punjab/Hb Q India hemoglobinopathy using Sebia capillary zone electrophoresis

    Directory of Open Access Journals (Sweden)

    Sushama Parab

    2014-01-01

    Full Text Available In India, hemoglobinopathies constitute a major genetic disorder and hemoglobin variants such as Hb S, Hb D Punjab, and Hb E are the most common ones. Other variants include Hb Q India, Hb Lepore, Hb J Meerut, Hb D Iran, etc. These variants show heterozygous state along with beta thalassemia. However, compound heterozygosities among these variants are very rare. Ethylenediaminetetraacetic acid whole blood sample received for routine thalassemia screening was subjected to alkaline electrophoresis using automated capillary zone electrophoresis. Suspecting the presence of rare variants, further analysis was carried out using Bio-Rad D10 and Tosoh G8 high-performance liquid chromatography (HPLC systems. Capillary zone electrophoretograms showed the presence of peaks in zone Hb A, Hb D, a fused peak in Hb A2, and a small peak in Z1 zone. Bio-Rad and Tosoh chromatograms also indicated the presence of four peaks which are identified as Hb A, Hb D Punjab, Hb Q India, and hybrid of Hb D Punjab/Hb Q India. A peak in Hb D zone of capillary was due to co-migration of Hb D Punjab and Hb Q India variants. Small peak in Z1 zone indicated the presence of alpha chain variant Hb Q India. The findings were further confirmed by HPLC results and molecular genetic studies. The present study reports for the 1 st time a rare hemoglobinopathy of double heterozygosity for Hb D Punjab, Hb Q India on Capillarys 2 Flex Piercing analyzer and is forth reported case for this rare hemoglobinopathy.

  15. Impact on Sensex of Scrapping Double Taxation of Dividends

    OpenAIRE

    Ragunathan V; Varma, Jayanth R.

    1997-01-01

    The taxation of dividends has generated an active debate in recent months in the media. While the industry representatives have been critical of the double taxation of dividends, the Government seems to be questioning the very premise that dividends are double taxed in India. The argument that scrapping the double taxation of dividends will give the Sensex a much needed boost seems to have tilted the scales. What will be the impact of scrapping of dividend tax on Sensex? One finds that the st...

  16. Experience during the monitoring of inactive scrap for the detection of inadvertent presence of radioactivity

    International Nuclear Information System (INIS)

    Sharma, Ranjit; Kumar, Anoj; Vikas; Patra, R.P.; Kumar, Vikas; Singh, Rajvir; Pradeepkumar, K.S.

    2012-01-01

    The inspection and certification of scrap material from nuclear facilities is a regulatory requirement to ensure that radioactive material will not reach public domain. Around the world, cases involving radioactive contamination of metallic components have occurred due to radioactive sources/contaminated metal scrap reaching the public domain. Radiological monitoring of inactive scrap material is essential as it may get into various usages in public domain where controls cannot be implemented. The method of detection is measurement of gamma dose rates due to any loose/fixed radioactive contamination in the scrap or presence of any radioactive material/source. In addition prevention of any inadvertent/malicious act leading to radioactive material reaching the public domain through scrap being essential, this monitoring gains further importance. This paper describes the methodology and experience in detection of presence of radioactivity at inactive Scrap monitoring facility. Even though radioactive sources of high strength with potential for serious environmental hazard have not been detected, few cases of contaminated material (MS plate/equipments etc with extremely low level of 137 Cs and Uranium contamination) have been detected and identified using portable gamma spectrometer. If proper monitoring is not carried out the dispersal of radioactivity to the environment can be a matter of concern due to metal scrap reaching recycling industry resulting in huge cost of decontamination and waste disposal. These events may also have negative impact on the export from the country resulting in economic losses. The impact of such events can be ruled out by effective scrap monitoring techniques which ensure that even small quantity of radioactivity escaping into public domain can be prevented. The methodology followed for monitoring of inactive scrap is found to be effective even for detection of presence of very low level of radioactivity

  17. Detection of Co-inheritance of Hb Hope and Hb Constant Spring in Three Thai Samples by Capillary Electrophoresis.

    Science.gov (United States)

    Panyasai, Sitthichai; Pornprasert, Sakorn

    2016-06-01

    The diagnosis of co-inheritance of Hb Hope [β136(H14)Gly → Asp, GGT > GAT] and Hb constant spring [Hb CS; α142, Term → Gln (TAA > CAA IN α2)] by high performance liquid chromatography (HPLC) is difficult because Hb Hope has a HPLC elution pattern similar to that of Hb Pyrgos, Hb New York, Hb Kodaira, and Hb Phimai. Moreover, the Hb CS mRNA, as well as the gene product, are unstable and present at a low level in peripheral blood. We report the use of a capillary electrophoresis (CE) for diagnosis of co-inheritance of Hb Hope and Hb CS in 3 Thai females who had mild anemia with Hb and Hct varying from 91-114 g/L to 0.28-0.36 L/L, respectively. Hb Hope eluted with a retention time of 125-140 s (Zone 10) of CE electrophoregram. Furthermore, the peak of Hb CS at the retention time of 245-250 s (Zone 2) was observed in these samples. In addition, the manual analysis by taking the non-black area under both peaks of HbA and Hb Hope (inverted V) into account provided the corrected Hb CS levels which are useful in screening of heterozygote or homozygote for Hb CS. Thus, the CE method provides an accurate diagnosis of Hb Hope and Hb CS which is useful in genetic counseling, prevention and control programs for these hemoglobinopathies.

  18. Catalytic extraction processing of contaminated scrap metal

    Energy Technology Data Exchange (ETDEWEB)

    Griffin, T.P.; Johnston, J.E.; Payea, B.M. [Molten Metal Technology, Inc., Waltham, MA (United States)] [and others

    1995-10-01

    The U.S. Department of Energy issued a Planned Research and Development Announcement (PRDA) in 1993, with the objective of identifying unique technologies which could be applied to the most hazardous waste streams at DOE sites. The combination of radioactive contamination with additional contamination by hazardous constituents such as those identified by the Resource Conservation and Recovery Act (RCRA) pose an especially challenging problem. Traditional remediation technologies are increasingly becoming less acceptable to stakeholders and regulators because of the risks they pose to public health and safety. Desirable recycling technologies were described by the DOE as: (1) easily installed, operated, and maintained; (2) exhibiting superior environmental performance; (3) protective of worker and public health and safety; (4) readily acceptable to a wide spectrum of evaluators; and (5) economically feasible. Molten Metal Technology, Inc. (MMT) was awarded a contract as a result of the PRDA initiative to demonstrate the applicability of Catalytic Extraction Processing (CEP), MMT`s proprietary elemental recycling technology, to DOE`s inventory of low level mixed waste. This includes DOE`s inventory of radioactively- and RCRA-contaminated scrap metal and other waste forms expected to be generated by the decontamination and decommissioning (D&D) of DOE sites.

  19. Catalytic extraction processing of contaminated scrap metal

    International Nuclear Information System (INIS)

    Griffin, T.P.; Johnston, J.E.; Payea, B.M.

    1995-01-01

    The U.S. Department of Energy issued a Planned Research and Development Announcement (PRDA) in 1993, with the objective of identifying unique technologies which could be applied to the most hazardous waste streams at DOE sites. The combination of radioactive contamination with additional contamination by hazardous constituents such as those identified by the Resource Conservation and Recovery Act (RCRA) pose an especially challenging problem. Traditional remediation technologies are increasingly becoming less acceptable to stakeholders and regulators because of the risks they pose to public health and safety. Desirable recycling technologies were described by the DOE as: (1) easily installed, operated, and maintained; (2) exhibiting superior environmental performance; (3) protective of worker and public health and safety; (4) readily acceptable to a wide spectrum of evaluators; and (5) economically feasible. Molten Metal Technology, Inc. (MMT) was awarded a contract as a result of the PRDA initiative to demonstrate the applicability of Catalytic Extraction Processing (CEP), MMT's proprietary elemental recycling technology, to DOE's inventory of low level mixed waste. This includes DOE's inventory of radioactively- and RCRA-contaminated scrap metal and other waste forms expected to be generated by the decontamination and decommissioning (D ampersand D) of DOE sites

  20. Evaluation of radioactive scrap metal recycling

    International Nuclear Information System (INIS)

    Nieves, L.A.; Chen, S.Y.; Kohout, E.J.; Nabelssi, B.; Tilbrook, R.W.; Wilson, S.E.

    1995-12-01

    This report evaluates the human health risks and environmental and socio-political impacts of options for recycling radioactive scrap metal (RSM) or disposing of and replacing it. Argonne National Laboratory (ANL) is assisting the US Department of Energy (DOE), Office of Environmental Restoration and Waste Management, Oak Ridge Programs Division, in assessing the implications of RSM management alternatives. This study is intended to support the DOE contribution to a study of metal recycling being conducted by the Task Group on Recycling and Reuse of the Organization for Economic Cooperation and Development. The focus is on evaluating the justification for the practice of recycling RSM, and the case of iron and steel scrap is used as an example in assessing the impacts. To conduct the evaluation, a considerable set of data was compiled and developed. Much of this information is included in this document to provide a source book of information

  1. Evaluation of radioactive scrap metal recycling

    Energy Technology Data Exchange (ETDEWEB)

    Nieves, L.A.; Chen, S.Y.; Kohout, E.J.; Nabelssi, B.; Tilbrook, R.W.; Wilson, S.E.

    1995-12-01

    This report evaluates the human health risks and environmental and socio-political impacts of options for recycling radioactive scrap metal (RSM) or disposing of and replacing it. Argonne National Laboratory (ANL) is assisting the US Department of Energy (DOE), Office of Environmental Restoration and Waste Management, Oak Ridge Programs Division, in assessing the implications of RSM management alternatives. This study is intended to support the DOE contribution to a study of metal recycling being conducted by the Task Group on Recycling and Reuse of the Organization for Economic Cooperation and Development. The focus is on evaluating the justification for the practice of recycling RSM, and the case of iron and steel scrap is used as an example in assessing the impacts. To conduct the evaluation, a considerable set of data was compiled and developed. Much of this information is included in this document to provide a source book of information.

  2. Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

    International Nuclear Information System (INIS)

    Biganzoli, Laura; Gorla, Leopoldo; Nessi, Simone; Grosso, Mario

    2012-01-01

    Highlights: ► Aluminium packaging partitioning in MSW incineration residues is evaluated. ► The amount of aluminium packaging recoverable from the bottom ashes is evaluated. ► Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. ► 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

  3. Measurement of HbA1c and HbA2 by Capillarys 2 Flex Piercing HbA1c programme for simultaneous management of diabetes and screening for thalassemia.

    Science.gov (United States)

    Ke, Peifeng; Liu, Jiawei; Chao, Yan; Wu, Xiaobin; Xiong, Yujuan; Lin, Li; Wan, Zemin; Wu, Xinzhong; Xu, Jianhua; Zhuang, Junhua; Huang, Xianzhang

    2017-10-01

    Thalassemia could interfere with some assays for haemoglobin A 1c (HbA 1c ) measurement, therefore, it is useful to be able to screen for thalassemia while measuring HbA 1c . We used Capillarys 2 Flex Piercing (Capillarys 2FP) HbA 1c programme to simultaneously measure HbA 1c and screen for thalassemia. Samples from 498 normal controls and 175 thalassemia patients were analysed by Capillarys 2FP HbA 1c programme (Sebia, France). For method comparison, HbA 1c was quantified by Premier Hb9210 (Trinity Biotech, Ireland) in 98 thalassaemia patients samples. For verification, HbA 1c from eight thalassaemia patients was confirmed by IFCC reference method. Among 98 thalassaemia samples, Capillarys 2FP did not provide an HbA 1c result in three samples with HbH due to the overlapping of HbBart's with HbA 1c fraction; for the remaining 95 thalassaemia samples, Bland-Altman plot showed 0.00 ± 0.35% absolute bias between two systems, and a significant positive bias above 7% was observed only in two HbH samples. The HbA 1c values obtained by Capillarys 2FP were consistent with the IFCC targets (relative bias below ± 6%) in all of the eight samples tested by both methods. For screening samples with alpha (α-) thalassaemia silent/trait or beta (β-) thalassemia trait, the optimal HbA 2 cut-off values were ≤ 2.2% and > 2.8%, respectively. Our results demonstrated the Capillarys 2FP HbA 1c system could report an accurate HbA 1c value in thalassemia silent/trait, and HbA 2 value (≤ 2.2% for α-thalassaemia silent/trait and > 2.8% for β-thalassemia trait) and abnormal bands (HbH and/or HbBart's for HbH disease, HbF for β-thalassemia) may provide valuable information for screening.

  4. Detection of contaminated metallurgical scrap at borders: a proposal for an 'investigation level'

    International Nuclear Information System (INIS)

    Duftschmid, K.E.

    1999-01-01

    refractory wear in blast furnaces with 60 Co sources mounted at different depth in the linings. After meltdown the resulting activity concentration is typically around several hundred Bq/kg, which is well below the Exemption Level according to the International Basic Safety Standards (BSS) of 10 kBq/kg. Such rejects are not only costly, but may seriously impede the free movement of goods. Several unnecessary alarms per day at a border would render the monitoring system useless in practice. Furthermore there is an economic restriction for the costs of border monitoring systems, in view of the very large number of units required to effectively cover a country. In contrast to the situation at steel plants, where every significant radioactive contamination of scrap should be detected to avoid meltdown of a source, the procedure at borders has to be based on a compromise. Derived from results obtained within a large scale pilot study on border monitoring systems (ITRAP), reported in a separate paper of this workshop, it is planned to propose, within the above mentioned Safety Guide, a recommended 'investigation level' at borders, i.e. a measured radiation level above which a scrap transport should be stopped and closely investigated, as a dose rate near the vehicle in the range of 0.3 μSv/h. This value, which is approximately equivalent to three times natural background, is supported by the fact that additional quality assurance measurements will generally be carried out by the industry. It is intended to eventually obtain international agreement between the Member States on this procedure. (author)

  5. Experience during the monitoring of inactive scrap for the detection of inadvertent presence of radioactivity

    International Nuclear Information System (INIS)

    Sharma, Ranjit; Anoj Kumar; Vikas; Singh, Rajvir; Patra, R.P.; Vikas Kumar; Pradeepkumar, K.S.

    2012-01-01

    The paper describes about the experience gained during the radiation monitoring of inactive scrap generated at various nuclear facilities. This type surveillance is carried out to prevent the spread of radioactivity in public domain and also as requirement by regulatory authorities. The inspection and certification of scrap material from nuclear facilities is a regulatory requirement to ensure that no radioactive material reaches public domain. This paper describes the methodology and experience in detection of radioactivity at inactive Scrap monitoring facility. Inactive scraps (metallic and non metallic) generated from various nuclear facilities of BARC, Trombay is dispatched to Trombay Village Store (TVS) for temporary storage before auction to the public. The monitoring at the facility includes visual inspection and radiation measurement before loading the scrap in the truck. An online PC based monitoring system and portable monitoring instruments in the range (nSv/h-µSv/h) are used to carry out radiation monitoring of inactive scrap loaded in a vehicle. Radioactive source of high activity with potential for serious environmental hazard has not been detected, but few cases of presence of radioactive/contaminated material (MS plate/equipments with low level of 137 Cs contamination) have been detected and identified using portable gamma spectrometer. Implementation of strict regulatory measures and radiation monitoring at nuclear facilities can minimize the probability of radioactive material reaching the public domain. The methodology followed for monitoring of inactive scrap is found to be effective even for detection of presence of radioactivity in scrap if any. (author)

  6. Probing the diphosphoglycerate binding pocket of HbA and HbPresbyterian (beta 108Asn --> Lys).

    Science.gov (United States)

    Gottfried, D S; Manjula, B N; Malavalli, A; Acharya, A S; Friedman, J M

    1999-08-31

    HbPresbyterian (beta 108Asn --> Lys, HbP) contains an additional positive charge (per alpha beta dimer) in the middle of the central cavity and exhibits a lower oxygen affinity than wild-type HbA in the presence of chloride. However, very little is known about the molecular origins of its altered functional properties. In this study, we have focused on the beta beta cleft of the Hb tetramer. Recently, we developed an approach for quantifying the ligand binding affinity to the beta-end of the Hb central cavity using fluorescent analogues of the natural allosteric effector 2, 3-diphosphoglycerate (DPG) [Gottfried, D. S., et al. (1997) J. Biol. Chem. 272, 1571-1578]. Time-correlated single-photon counting fluorescence lifetime studies were used to assess the binding of pyrenetetrasulfonate to both HbA and HbP in the deoxy and CO ligation states under acidic and neutral pH conditions. Both the native and mutant proteins bind the probe at a weak binding site and a strong binding site; in all cases, the binding to HbP was stronger than to HbA. The most striking finding was that for HbA the binding affinity varies as follows: deoxy (pH 6.35) > deoxy (pH 7.20) > CO (pH 6.35); however, the binding to HbP is independent of ligation or pH. The mutant oxy protein also hydrolyzes p-nitrophenyl acetate, through a reversible acyl-imidazole pathway linked to the His residues of the beta beta cleft, at a considerably higher rate than does HbA. This implies a perturbation of the microenvironment of these residues at the DPG binding pocket. Structural consequences due to the presence of the new positive charge in the middle of the central cavity have been transmitted to the beta beta cleft of the protein, even in its liganded conformation. This is consistent with a newly described quaternary state (B) for liganded HbPresbyterian and an associated change in the allosteric control mechanism.

  7. The effect of material productivity on scrap reduction on aluminum reduction pot process

    Science.gov (United States)

    Huda, L. N.

    2018-02-01

    Scrap in the production process is defined as part of production that can not be accepted as the final product due to production failure. The amount of scarp occurring in the reduction pot production process of one of the aluminum smelting furnaces exceeds the acceptance standard of 5 to 10%. This affects the amount of production produced. The purpose of this study is to reduce the amount of scrap produced to increase the productivity of the materials used. The solution is carried-out by making improvements using Lean Six Sigma method. In the initial calculation, material productivity ranged from 0.88. Based on the study, the factors that cause the high amount of scrap produced is the use of Na2O which is inserted into the alumina is different in size and the influence of noise that occurs in pots that are difficult to control. The analysis base on Lean Six Sigma obtained process cycle efficiency (PCE) equal to 86,92% for actual condition. Process improvement is carried-out through define, measure, analyze, improve and control procedure on Na2O feeding process and PCE value decrease 6,05%. This indicates that increased process capability will reduce scrap. A decrease in scrap amount of about 6% will be able to increase material productivity by 0.05%. This indicates that continuous process control is needed to decrease the number of scraps and increase productivity.

  8. Investigation of fatigue and mechanical properties of the pipe grade poly(vinyl chloride using recycled scraps

    Directory of Open Access Journals (Sweden)

    J-M. Lee

    2015-04-01

    Full Text Available In this paper, the effect of using pre-consumer PVC scraps on static and long-term mechanical properties is studied. The degradation characteristics of mixing virgin PVC with crushed pre-consumer and PVC pipe scraps are analyzed using various tools including Gel Permeation Chromatography (GPC, Thermogravimetric Analysis (TGA, X-ray fluorescence (XRF and Fourier Transform Infrared (FTIR spectroscopy. The variation of static mechanical properties as a function of adding pre-consumer PVC pipe scraps is investigated using the degradation analyses of recycled PVC scraps. In addition, fatigue tests are executed to evaluate the long-term durability of blending virgin PVC and recycled PVC scraps, and the fracture surface is investigated in detail to reveal the variation of the fracture mechanisms.

  9. Permanent LMN denervation of human skeletal muscle and recovery by h-b FES: management and monitoring

    Directory of Open Access Journals (Sweden)

    Helmut Kern

    2010-09-01

    Full Text Available Denervation of a defined skeletal muscle is due to lower motor neuron (LMN or peripheral nerve lesions that have major consequences on the muscle tissue. After early atrophy, the mid- and late-phases presents two very contrasting myofibers populations: beside those severely atrophic with internalized groups of myonuclei, large fast-type muscle fibers continue to be present 4 to 6 years after Spinal Cord Injury (SCI. Recent results of rat experiments provides the rational basis for understanding the residual functional characteristics of the long-term denervated muscle and the molecular explanation of its ability to respond to home-base functional electrical stimulation (h-b FES using custom-designed electrodes and stimulators. Further outcomes of the Vienna-Padova ten-year collaboration are: 1. a world-unique Myo- Bank of muscle biopsies and 2. improved imaging procedures (Color Computer Tomography (CT scan and Functional Echomyography, all demonstrating that h-b FES induces improvements in muscle contractility, tissue composition and mass, despite permanent LMN denervation. The benefits of h-b FES could be extended from patents suffering with complete Conus-Cauda Syndrome to the numerous patients with incomplete LMN denervation of skeletal muscles to determine whether h-b FES reduces secondary complications related to disuse and impaired blood perfusion (reduction in bone density, risk of bone fracture, decubitus ulcers, and pulmonary thromboembolism. We are confident that translation of the results of a clinical experiment, the EU Project RISE, to the larger cohort of incomplete LMN denervated muscles will provide the wanted results.

  10. Scrap supply in Bosnian after war situation - sources, quality, regulation and control

    International Nuclear Information System (INIS)

    Pihura, Dervis

    1999-01-01

    Before the war, the Bosnian foundry and steel industry were supplied with scrap partly from domestic sources but mainly from foreign market. The annual steel production before the war recorded 130,000 tonnes of casting and 2,000.000 tonnes of crude steel. Most of the scrap was imported to secure and stabilize the production. During and after the war, despite a significant loss of production, efforts have been made to return to the normal production level in many ways. In the wake of the war, there has been a growing concern over the import of radioactive contaminated metallurgical scrap or low quality raw materials which are uncontrolled or of unidentified sources. In this regard, it is urgently required to establish an effective system to prevent from, to detect and to control the flow of the radioactive contaminated metallurgical scrap. The system should be established in such a way that all sorts of radioactive metallurgical elements should be controlled and prevented from use in all the metallurgical manufacturing processes, ferrous and non-ferrous alike. The coverage of control should start from the border or (air) port checkpoint where the flow of the scrap begins to the final steel product. The control system should take a form of internationally common and acceptable standards and regulations. Equipments and measurement techniques should also be internationally common. (author)

  11. K2-EDTA and K3-EDTA Greiner Tubes for HbA1c Measurement.

    Science.gov (United States)

    Vrtaric, Alen; Filipi, Petra; Hemar, Marina; Nikolac, Nora; Simundic, Ana-Maria

    2016-02-01

    To determine whether K2-ethylenediaminetetraacetic acid (EDTA) and K3-EDTA Greiner tubes could be used interchangeably for glycosylated hemoglobin, type A1C (HbA1c) measurement via the Abbott Laboratories ARCHITECT chemiluminescent microparticle HbA1c assay on the ARCHITECT i2000SR immunoanalyzer at our university hospital. We drew blood from a total of 45 outpatients into plastic Greiner Vacuette tubes, some of which were lined with K2-EDTA and others with K3-EDTA anticoagulant. Data are presented as median and interquartile range values. We used the Wilcoxon test and Passing-Bablok regression for tube comparison. For K2-EDTA tubes median HbA1c concentration was 54 mmol/mol (41 to 71 mmol/mol) and for K3-EDTA tubes 56 mmol/mol (43 to 69 mmol/mol). There was no statistically significant difference between K2-EDTA and K3-EDTA (bias= -1.29 mmol/mol; P = 0.24). Passing-Bablok regression showed that there is no constant and proportional error: y = -0.23 (95% CI[-3.52 to 0.69]) + 1.00( 95% CI[0.98 to 1.06]) x. In this study, we provide evidence for the lack of any clinically and statistically significant bias between K2-EDTA and K3-EDTA HbA1c measurements. Thus, Greiner tubes lined with K2-EDTA and those lined with K3-EDTA can safely be used interchangeably to measure HbA1c via the Abbott Laboratories ARCHITECT assay. © American Society for Clinical Pathology, 2015. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

  12. Prognostic factors for recovery in Portuguese patients with Bell's palsy.

    Science.gov (United States)

    Ferreira, Margarida; Firmino-Machado, João; Marques, Elisa A; Santos, Paula C; Simões, Ana Daniela; Duarte, José A

    2016-10-01

    The main aim of this study was to identify the prognostic factors that contribute to complete recovery at 6 weeks and 6 months in patients with Bell's palsy. This is a prospective, longitudinal, and descriptive study that included 123 patients diagnosed with facial nerve palsy (FNP) at a hospital in Guimarães, Portugal. However, only 73 patients with Bell's palsy (BP) were included in the assessment of recovery at 6 weeks and 6 months. We analyzed the demographic and clinical characteristics of the patients, including sex, age, paralyzed side, occupation, previous and associated symptoms, seasonal occurrence, familial facial palsy, patient perception, intervention options, and baseline grade according to the House-Brackmann facial grading system (HB-FGS). Of the 123 cases with FNP, 79 (64.2%) patients had BP. Age, sex, and baseline HB-FGS grades were significant predictors of complete recovery at 6 weeks. Patients with HB-FGS grade III or lower (6 weeks baseline) had significant recovery of function at 6 months. Baseline severity of BP, elderly patients, and male sex were early predictors of poor prognosis. Patients with mild and moderate dysfunction according to the HB-FGS achieved significant normal facial function at 6 months. Further prospective studies with longer observation periods and larger samples are needed to verify the results.

  13. Dietary determinants for Hb-acrylamide and Hb-glycidamide adducts in Danish non-smoking women

    DEFF Research Database (Denmark)

    Outzen, Malene; Egeberg, Rikke; Dragsted, Lars

    2011-01-01

    in erythrocytes were analysed by liquid chromatography/MS/MS. Dietary determinants were evaluated by multiple linear regression analyses adjusted for age and smoking behaviour among ex-smokers. The median for Hb-AA was 35 pmol/g globin (5th percentile 17, 95th percentile 89) and for Hb-GA 21 pmol/g globin (5th......Acrylamide (AA) is a probable human carcinogen that is formed in heat-treated carbohydrate-rich foods. The validity of FFQ to assess AA exposure has been questioned. The aim of the present cross-sectional study was to investigate dietary determinants of Hb-AA and Hb-glycidamide (GA) adducts....... The study included 537 non-smoking women aged 50–65 years who participated in the Diet, Cancer and Health cohort (1993–97). At study baseline, blood samples and information on dietary and lifestyle variables obtained from self-administered questionnaires were collected. From blood samples, Hb-AA and Hb-GA...

  14. A Novel Double Heterozygous Hb D-Punjab/Hb J-Meerut Hemoglobinopathy.

    Science.gov (United States)

    Chandra, Dinesh; Tyagi, Seema; Deka, Roopam; Chauhan, Richa; Seth, Tulika; Saxena, Renu; Pati, H P

    2017-12-01

    A comprehensive laboratory diagnosis of hemoglobinopathies forms an integral part in workup of disorders of globin chain synthesis. Clinical findings, complete blood counts, peripheral smear examination along with hemoglobin (Hb) electrophoresis and/or cation exchange high performance liquid chromatography findings and parental study helps to clinch a final diagnosis. Compound heterozygous hemoglobinopathy presents with variable clinical findings and some of them are picked up on screening tests done as part of routine antenatal workup. Here we report a rare double heterozygous hemoglobinopathy of Hb D-Punjab and Hb J-Meerut in a 35 year antenatal female.

  15. Transboundary Movement of Radioactively Contaminated Scrap Metal - Lessons Learned

    Energy Technology Data Exchange (ETDEWEB)

    Nizamska, M., E-mail: m.nimzamska@bnra.bg [Emergency Planning and Preparedness Division, Bulgarian Nuclear Regulatory Agency, Sofia (Bulgaria)

    2011-07-15

    Starting in 1989, Bulgaria has undergone a comprehensive transformation of its economy and social conditions. Part of this process is related to the intensive privatization that started in 2001. This privatization included facilities, as well as sites that use radioactive material for different applications - industry, medicine, agriculture, science, etc. The rapid change of property ownership and, in some cases, the resulting bankruptcy, has caused difficulties in tracing and identifying radioactive sources and materials and a deterioration of the system of safety, physical protection, etc. of radioactive material. In some cases, radioactive sources were stolen because of the value of their protective containers and sold for scrap metal. This led to the occurrence of different types of radiation incidents, mainly related to the discovery of radioactive sources in scrap metal. The consequences of these incidents include the risk of radiation exposure of the workers at scrap metal yards or reprocessing facilities and of members of the public and, in addition, radioactive contamination of the environment. The Bulgarian Nuclear Regulatory Agency (BNRA) has been responding to these incidents and has carried out a series of measures to improve the control over materials (e.g. activated or surface contaminated materials) and radioactive sources and to strengthen the preventive, monitoring, emergency preparedness and mitigating measures at facility, national and transboundary levels. This paper presents an analysis of the lessons learned by the BNRA and of the control of the transboundary movement of radioactively contaminated scrap metal through the territory of Bulgaria. (author)

  16. The melting treatment of bulk scrap from decommissioning

    International Nuclear Information System (INIS)

    Deng Junxian; Deng Feng

    2014-01-01

    Large amount of radioactive scrap will come out from reactor decommissioning. The melting treatment can be used for the volume reduction, the recycle and reuse of the radioactive scrap to reduce the mass of the radioactive waste disposal and to reuse most of the metal. The melting treatment has the advantages in volume reduction, conditioning, radionuclide confinement, reduction of radioactivity concentration, easy monitoring of radioactivity; and the effective of decontamination for several radionuclide. Therefore to use the melting technology other decontamination technology should be performed ahead, the decontamination effect of the melting should be predicted, the utility of recycle and reuse should be defined, and the secondary waste should be controlled effectively. (authors)

  17. Lead scrap processing in rotary furnaces: a review

    Energy Technology Data Exchange (ETDEWEB)

    Rousseau, M

    1987-01-01

    Formerly, the lead scrap had been processed mainly in reverberatory and shaft furnaces or, even, in rotary furnaces (R.F.). The direct smelting of battery scrap entrains an expensive pollution control and high operating costs because of slag recirculation, coke consumption, losses in slag and matte. Nowadays, mechanized battery wrecking plants allow selective separation of casings and separators from metallic Pb (grids, poles, solders) as well as lead in non-metallic form (PbSO/sub 4/, PbO, PbO/sub 2/, contaminated with some Sb) frequently called paste. Because of their high performance and flexibility in metallurgical processing (melting, reducing, oxidizing and selective pouring) the R.F. supersedes the reverberatory furnace worldwide.

  18. A Pilot Assessment of Occupational Health Hazards in the US Electronic Scrap Recycling Industry.

    Science.gov (United States)

    Ceballos, Diana M; Gong, Wei; Page, Elena

    2015-01-01

    The National Institute for Occupational Safety and Health (NIOSH) surveyed a randomly selected sample of electronic scrap (e-scrap) recycling facilities nationwide to characterize work processes, exposures, and controls. Despite multiple attempts to contact 278 facilities, only 47 responded (17% response rate). Surveyed facilities reported recycling a wide variety of electronics. The most common recycling processes were manual dismantling and sorting. Other processes included shredding, crushing, and automated separation. Many facilities reported that they had health and safety programs in place. However, some facilities reported the use of compressed air for cleaning, a practice that can lead to increased employee dust exposures, and some facilities allowed food and drinks in the production areas, a practice that can lead to ingestion of contaminants. Although our results may not be generalizable to all US e-scrap recycling facilities, they are informative regarding health and safety programs in the industry. We concluded that e-scrap recycling has the potential for a wide variety of occupational exposures particularly because of the frequent use of manual processes. On-site evaluations of e-scrap recyclers are needed to determine if reported work processes, practices, and controls are effective and meet current standards and guidelines. Educating the e-scrap recycling industry about health and safety best practices, specifically related to safe handling of metal dust, would help protect employees.

  19. Process for removing and detoxifying cadmium from scrap metal including mixed waste

    International Nuclear Information System (INIS)

    Kronberg, J.W.

    1994-01-01

    Cadmium-bearing scrap from nuclear applications, such as neutron shielding and reactor control and safety rods, must usually be handled as mixed waste since it is radioactive and the cadmium in it is both leachable and highly toxic. Removing the cadmium from this scrap, and converting it to a nonleachable and minimally radioactive form, would greatly simplify disposal or recycling. A process now under development will do this by shredding the scrap; leaching it with reagents which selectively dissolve out the cadmium; reprecipitating the cadmium as its highly insoluble sulfide; then fusing the sulfide into a glassy matrix to bring its leachability below EPA limits before disposal. Alternatively, the cadmium may be recovered for reuse. A particular advantage of the process is that all reagents (except the glass frit) can easily be recovered and reused in a nearly closed cycle, minimizing the risk of radioactive release. The process does not harm common metals such as aluminum, iron and stainless steel, and is also applicable to non-nuclear cadmium-bearing scrap such as nickel-cadmium batteries

  20. US Department of Energy`s weapons complex scrap metal inventory. Research report

    Energy Technology Data Exchange (ETDEWEB)

    Duda, J.R.

    1993-07-01

    Two tasks comprise the thrust of this contracted effort. Task 1 is the development of a Source List and is based on determining a list of public documents pertaining to contaminated/uncontaminated scrap metals, equipment, and other materials of value, were they not contaminated or could they be decontaminated. Task 2 is to develop an inventory of such materials from the Task 1 list of public documentation. In more detail, the Task 2 Inventory Report is based upon fulfillment of the following requirement to prepare and submit an Inventory Report based on the information obtained in the Source List. The Inventory Report shall define the type, quantity, and location of used equipment, scrap metal, and other materials existing within DOE`s system. The Inventory Report shall list: the site where the equipment, scrap metal, or other material resides; the type and size of equipment; the type and volume and/or weight of scrap metal or other material; its source; the type and level of contamination; its accessibility; the current annual rate of generation; and the projected annual rate of generation of the material.

  1. Life cycle assessment of resource recovery from municipal solid waste incineration bottom ash

    DEFF Research Database (Denmark)

    Allegrini, Elisa; Vadenbo, Carl; Boldrin, Alessio

    2015-01-01

    Bottom ash, the main solid output from municipal solid waste incineration (MSWI), has significant potential for the recovery of resources such as scrap metals and aggregates. The utilisation of these resources ideally enables natural resources to be saved. However, the quality of the recovered...

  2. Effects of cold water immersion and active recovery on hemodynamics and recovery of muscle strength following resistance exercise.

    Science.gov (United States)

    Roberts, Llion A; Muthalib, Makii; Stanley, Jamie; Lichtwark, Glen; Nosaka, Kazunori; Coombes, Jeff S; Peake, Jonathan M

    2015-08-15

    Cold water immersion (CWI) and active recovery (ACT) are frequently used as postexercise recovery strategies. However, the physiological effects of CWI and ACT after resistance exercise are not well characterized. We examined the effects of CWI and ACT on cardiac output (Q̇), muscle oxygenation (SmO2), blood volume (tHb), muscle temperature (Tmuscle), and isometric strength after resistance exercise. On separate days, 10 men performed resistance exercise, followed by 10 min CWI at 10°C or 10 min ACT (low-intensity cycling). Q̇ (7.9 ± 2.7 l) and Tmuscle (2.2 ± 0.8°C) increased, whereas SmO2 (-21.5 ± 8.8%) and tHb (-10.1 ± 7.7 μM) decreased after exercise (P < 0.05). During CWI, Q̇ (-1.1 ± 0.7 l) and Tmuscle (-6.6 ± 5.3°C) decreased, while tHb (121 ± 77 μM) increased (P < 0.05). In the hour after CWI, Q̇ and Tmuscle remained low, while tHb also decreased (P < 0.05). By contrast, during ACT, Q̇ (3.9 ± 2.3 l), Tmuscle (2.2 ± 0.5°C), SmO2 (17.1 ± 5.7%), and tHb (91 ± 66 μM) all increased (P < 0.05). In the hour after ACT, Tmuscle, and tHb remained high (P < 0.05). Peak isometric strength during 10-s maximum voluntary contractions (MVCs) did not change significantly after CWI, whereas it decreased after ACT (-30 to -45 Nm; P < 0.05). Muscle deoxygenation time during MVCs increased after ACT (P < 0.05), but not after CWI. Muscle reoxygenation time after MVCs tended to increase after CWI (P = 0.052). These findings suggest first that hemodynamics and muscle temperature after resistance exercise are dependent on ambient temperature and metabolic demands with skeletal muscle, and second, that recovery of strength after resistance exercise is independent of changes in hemodynamics and muscle temperature. Copyright © 2015 the American Physiological Society.

  3. Characterization of Irradiated and Non-Irradiated Rubber from Automotive Scrap Tires

    Science.gov (United States)

    Souza, Clécia Moura; Silva, Leonardo G.

    The aim of this work was to characterize the samples of irradiated and non-irradiated rubber from automotive scrap tires. Rubber samples from scrap tires were irradiated at irradiation doses of 200, 400 and 600kGy in an electron beam accelerator. Subsequently, both the irradiated and non-irradiated samples were characterized by thermogravimetry (TG), differential scanning calorimetry (DSC), tensile strength mechanical test, and Fourier transform infrared (FTIR) spectrophotometry.

  4. Quantitative Trait Loci Influencing Hb F Levels in Southern Thai Hb E (HBB: c.79G>A) Heterozygotes.

    Science.gov (United States)

    Kesornsit, Aumpika; Jeenduang, Nutjaree; Horpet, Dararat; Plyduang, Thunyaluk; Nuinoon, Manit

    2018-01-01

    Variation of fetal hemoglobin (Hb F) expression in heterozygous Hb E (HBB: c.79G>A) individuals is associated with several genetic modifiers and not well understood. This study was undertaken in order to determine the effect of single nucleotide polymorphisms (SNPs), including XmnI G γ (rs7482144), rs766432 on the BCL11A gene and rs9376074 on the HBS1L gene, on Hb F levels in Southern Thai heterozygous Hb E individuals. A total of 97 Southern Thai subjects carrying heterozygous Hb E were selected for the hematological study. After excluding the samples with α-thalassemia (α-thal) interaction or moderate anemia, because both conditions can affect the hematological parameters, the remaining 74 samples were submitted to SNP analysis. Hematological parameters were measured using an automated hematology analyzer and high performance liquid chromatography (HPLC). The results show that rs766432 was strongly associated with increased Hb F levels and rs7482144 was associated with Hb F levels in each subgroup (genotype) of rs766432. This study suggested that the BCL11A locus has a major effect on Hb F levels compared with the XmnI polymorphism in Hb E heterozygotes. This association of Hb F levels with SNPs is useful for the interpretation of hemoglobin (Hb) typing in heterozygous Hb E samples with high Hb F levels. Future research will need to address the better understanding of the mechanisms of the SNPs that regulate Hb F production without stress erythropoiesis in Hb E heterozygotes.

  5. The Research of Scrapped Automobiles Recycling and Disassembling Industry Development Based on Auto Industry Chain

    Directory of Open Access Journals (Sweden)

    linhua Pang

    2015-01-01

    Full Text Available The number of China’s scrapped car is on an explosively growing trend, and the development of scrapped car recycling industry has a golden prospect. The current scrapped car recycling system is not perfect in our country, because related industries driven by market develop slowly, and there are some outstanding problems such as potential safety risks, environmental pollution and resource waste. The paper analyzes and studies the existing problems and countermeasures to investigate the development strategy of scrapped car recycling industry according to the whole automobile industry chain construction, technology and equipment conditions, policy guidance, etc. and at last explore the new industrial development pattern of serving automobile reverse design.

  6. Health risk and impact evaluation for recycling of radioactive scrap metal

    International Nuclear Information System (INIS)

    Nieves, L.A.; Chen, S.Y.; Murphie, W.E.; Lilly, M.J. III

    1994-01-01

    The DoE, Office of Environmental Restoration and Waste Management, is participating with the Organization for Economic Cooperation and Development in providing analytical support for developing international standards for recycling of radioactive scrap metals. For this purpose, Argonne National Laboratory is assessing health, environmental and societal implications of recycling and/or disposal process alternatives. This effort includes development of international inventory estimates for contaminated metals; investigation of international scrap metal markets; assessment of radiological and non-radiological human health risks; impacts on environmental quality and resources; and investigation of social and political factors. The RSM disposal option is being assessed with regard to the environmental and health impacts of replacing the metals if they are withdrawn from use. Impact estimates are developed for steel as an illustrative example because steel comprises a major portion of the scrap metal inventory. Current and potential sources of RSM include nuclear power plants, fuel cycle and weapons production facilities, industrial and medical facilities and equipment, and petroleum and phosphate rock extraction equipment. Millions of metric tons (t) of scrap iron and steel, stainless steel, and copper, as well as lesser quantities of aluminum, nickel, lead, and zirconium, are likely to become available in the future as these facilities are withdrawn from service

  7. Volatilisation and oxidation of aluminium scraps fed into incineration furnaces

    Energy Technology Data Exchange (ETDEWEB)

    Biganzoli, Laura, E-mail: laura.biganzoli@mail.polimi.it [Politecnico di Milano, Piazza L. Da Vinci 32, 20133 Milano (Italy); Gorla, Leopoldo; Nessi, Simone; Grosso, Mario [Politecnico di Milano, Piazza L. Da Vinci 32, 20133 Milano (Italy)

    2012-12-15

    Highlights: Black-Right-Pointing-Pointer Aluminium packaging partitioning in MSW incineration residues is evaluated. Black-Right-Pointing-Pointer The amount of aluminium packaging recoverable from the bottom ashes is evaluated. Black-Right-Pointing-Pointer Aluminium packaging oxidation rate in the residues of MSW incineration is evaluated. Black-Right-Pointing-Pointer 80% of aluminium cans, 51% of trays and 27% of foils can be recovered from bottom ashes. - Abstract: Ferrous and non-ferrous metal scraps are increasingly recovered from municipal solid waste incineration bottom ash and used in the production of secondary steel and aluminium. However, during the incineration process, metal scraps contained in the waste undergo volatilisation and oxidation processes, which determine a loss of their recoverable mass. The present paper evaluates the behaviour of different types of aluminium packaging materials in a full-scale waste to energy plant during standard operation. Their partitioning and oxidation level in the residues of the incineration process are evaluated, together with the amount of potentially recoverable aluminium. About 80% of post-consumer cans, 51% of trays and 27% of foils can be recovered through an advanced treatment of bottom ash combined with a melting process in the saline furnace for the production of secondary aluminium. The residual amount of aluminium concentrates in the fly ash or in the fine fraction of the bottom ash and its recovery is virtually impossible using the current eddy current separation technology. The average oxidation levels of the aluminium in the residues of the incineration process is equal to 9.2% for cans, 17.4% for trays and 58.8% for foils. The differences between the tested packaging materials are related to their thickness, mechanical strength and to the alloy.

  8. The Influence of Home Scrap on Mechanical Properties of MgAl9Zn1 Alloy Castings

    Directory of Open Access Journals (Sweden)

    Konopka Z.

    2017-06-01

    Full Text Available The work presents the results of examinations concerning the influence of various amounts of home scrap additions on the properties of castings made of MgAl9Zn1 alloy. The fraction of home scrap in the metal charge ranged from 0 to 100%. Castings were pressure cast by means of the hot-chamber pressure die casting machine under the industrial conditions in one of the domestic foundries. The examinations consisted in the determination of the following properties: tensile strength Rm, yield strength Rp0.2, and the unit elongation A5, all being measured during the static tensile test. Also, the hardness measurements were taken by the Brinell method. It was found that the mechanical properties (mainly the strength properties are being improved up to the home scrap fraction of 50%. Their values were increased by about 30% over this range. Further rise in the home scrap content, however, brought a definite decrease in these properties. The unit elongation A5 exhibited continual decrease with an increase in the home scrap fraction in the metal charge. A large growth of hardness was noticed for the home scrap fraction increasing up to the value of 50%. Further increasing the home scrap percentage, however, did not result in a significant rise of the hardness value any more.

  9. Hemoglobin Constant Spring (Hb CS) Missed by HPLC in an Hb E Trait Pregnancy Resulting in Hb H-CS Disease in a Thai Girl: Utility of Capillary Electrophoresis.

    Science.gov (United States)

    Pornprasert, Sakorn; Saoboontan, Supansa; Wiengkum, Thanatcha

    2016-06-01

    Hemoglobin Constant Spring [Hb CS; α142, Term→Gln (TAA>CAA IN α2)] is often missed by routine laboratory testing, especially in subjects with co-inheritance of β-thalassemia or β-variants. We reported the case of a 1-year-old female with Hb H-CS disease who was born from a father with heterozygous of α-thalassemia-1 Southeast Asian type deletion and a mother with the combination of Hb CS and Hb E [β26 (B8) Glu→Lys, GAG>AAG] trait. A very tiny peak of Hb CS of the mother was easily ignored on the high performance liquid chromatography chromatogram while it was clearly seen on the capillary electrophoresis (CE) electrophoregram. Therefore, the CE is useful in screening for heterozygous Hb CS in a person with Hb E trait. This is of potential benefit for prevention of new cases of Hb H-CS disease.

  10. Thermogravimetric characteristics and kinetics of scrap tyre and Juglans regia shell co-pyrolysis.

    Science.gov (United States)

    Uzun, B B; Yaman, E

    2014-10-01

    The degradation kinetics of Juglans regia shell, scrap tyre and their blends were investigated using a thermogravimetric analysis method. Experiments were performed under dynamic conditions and a nitrogen atmosphere in the range 293 to 973 K at different heating rates. During pyrolysis of J. regia shell three mass loss zones were specified as removal of water, decomposition of hemicelluloses and cellulose, and decomposition of lignin. The degradation curves of scrap tyre showed merely one stage which was due to decomposition of styrene butadiene rubber. The kinetic parameters were calculated using both Arrhenius and Coats-Redfern methods. By adopting the Arrhenius method, the average value of activation energies of J. regia shell, scrap tyre and their 1 : 1 blends were found to be 69.22, 71.48 and 47.03 kJ mol(-1), respectively. Additionally, by using the Coats-Redfern method, the average value of activation energies of J. regia shell, scrap tyre and their 1 : 1 blend were determined as 99.85, 78.72 and 63.81 kJ mol(-1), respectively. The addition of J. regia shell to scrap tyre caused a reduction in the activation energies. The difference of weight loss was measured to examine interactions between raw materials. The maximum difference between experimental and theoretical mass loss was 5% at about 648 K with a heating rate of 20 K min(-1). These results indicated a significant synergistic effect was available during co-pyrolysis of J. regia shell and scrap tyre in the high temperature region. © The Author(s) 2014.

  11. Assessment of recycling or disposal alternatives for radioactive scrap metal

    International Nuclear Information System (INIS)

    Murphie, W.E.; Lilly, M.J. III; Nieves, L.A.; Chen, S.Y.

    1993-01-01

    The US Department of Energy, Office of Environmental Restoration and Waste Management, Oak Ridge Programs Division, is participating with the Organization for Economic Cooperation and Development in providing analytical support for evaluation of management alternatives for radioactive scrap metals. For this purpose, Argonne National Laboratory is assessing environmental and societal implications of recycling and/or disposal process alternatives. This effort includes development of inventory estimates for contaminated metals; investigation of scrap metal market structure, processes, and trends; assessment of radiological and nonradiological effects of recycling; and investigation of social and political factors that are likely to either facilitate or constrain recycling opportunities. In addition, the option of scrap metal disposal is being assessed, especially with regard to the environmental and health impacts of replacing these metals if they are withdrawn from use. This paper focuses on the radiological risk assessment and dose estimate sensitivity analysis. A open-quotes tieredclose quotes concept for release categories, with and without use restrictions, is being developed. Within the tiers, different release limits may be indicated for specific groupings of radionuclides. Depending on the spectrum of radionuclides that are present and the level of residual activity after decontamination and/or smelting, the scrap may be released for unrestricted public use or for specified public uses, or it may be recycled within the nuclear industry. The conservatism of baseline dose estimates is examined, and both more realistic parameter values and protective measures for workers are suggested

  12. Fully automated laboratory for the assay of plutonium in wastes and recoverable scraps

    International Nuclear Information System (INIS)

    Guiberteau, P.; Michaut, F.; Bergey, C.; Debruyne, T.

    1990-01-01

    To determine the plutonium content of wastes and recoverable scraps in intermediate size containers (ten liters) an automated laboratory has been carried out. Two passive methods of measurement are used. Gamma ray spectrometry allows plutonium isotopic analysis, americium determination and plutonium assay in wastes and poor scraps. Calorimetry is used for accurate (± 3%) plutonium determination in rich scraps. A full automation was realized with a barcode management and a supply robot to feed the eight assay set-ups. The laboratory works on a 24 hours per day and 365 days per year basis and has a capacity of 8,000 assays per year

  13. The super sickling haemoglobin HbS-Oman: a study of red cell sickling, K+ permeability and associations with disease severity in patients heterozygous for HbA and HbS-Oman (HbA/S-Oman genotype).

    Science.gov (United States)

    Al Balushi, Halima W M; Wali, Yasser; Al Awadi, Maha; Al-Subhi, Taimoora; Rees, David C; Brewin, John N; Hannemann, Anke; Gibson, John S

    2017-10-01

    Studying different sickle cell genotypes may throw light on the pathogenesis of sickle cell disease (SCD). Here, the clinical profile, red cell sickling and K + permeability in 29 SCD patients (15 patients with severe disease and 14 with a milder form) of HbA/S-Oman genotype were analysed. The super sickling nature of this Hb variant was confirmed. The red cell membrane permeability to K + was markedly abnormal with elevated activities of P sickle , Gardos channel and KCl cotransporter (KCC). Results were consistent with Ca 2+ entry and Mg 2+ loss via P sickle stimulating Gardos channel and KCC activities. The abnormal red cell behaviour was similar to that in the commonest genotype of SCD, HbSS, in which the level of mutated Hb is considerably higher. Although activities of all three K + transporters also correlated with the level of HbS-Oman, there was no association between transport phenotype and disease severity. The super sickling behaviour of HbS-Oman may obviate the need for solute loss and red cell dehydration to encourage Hb polymerisation, required in other SCD genotypes. Disease severity was reduced by concurrent α thalassaemia, as observed in other SCD genotypes, and represents an obvious genetic marker for prognostic tests of severity in young SCD patients of the HbA/S-Oman genotype. © 2017 John Wiley & Sons Ltd.

  14. Advanced technologies for decontamination and conversion of scrap metal

    International Nuclear Information System (INIS)

    Muth, T.R.; Shasteen, K.E.; Liby, A.L.

    1995-01-01

    The Department of Energy (DOE) accumulated large quantities of radioactive scrap metal (RSM) through historic maintenance activities. The Decontamination and Decommissioning (D ampersand D) of major sites formerly engaged in production of nuclear materials and manufacture of nuclear weapons will generate additional quantities of RSM, as much as 3 million tons of such metal according to a recent study. The recycling of RSM is quickly becoming appreciated as a key strategy in DOE's cleanup of contaminated sites and facilities. The work described here has focused on recycle of the concentrated and high-value contaminated scrap metal resource that will arise from cleanup of DOE's gaseous diffusion plants

  15. Advanced technologies for decontamination and conversion of scrap metal

    Energy Technology Data Exchange (ETDEWEB)

    Muth, T.R.; Shasteen, K.E.; Liby, A.L. [Manufacturing Sciences Corp., Oak Ridge, TN (United States)] [and others

    1995-10-01

    The Department of Energy (DOE) accumulated large quantities of radioactive scrap metal (RSM) through historic maintenance activities. The Decontamination and Decommissioning (D&D) of major sites formerly engaged in production of nuclear materials and manufacture of nuclear weapons will generate additional quantities of RSM, as much as 3 million tons of such metal according to a recent study. The recycling of RSM is quickly becoming appreciated as a key strategy in DOE`s cleanup of contaminated sites and facilities. The work described here has focused on recycle of the concentrated and high-value contaminated scrap metal resource that will arise from cleanup of DOE`s gaseous diffusion plants.

  16. Hydrogen isotope storage in zircaloy scrap

    Energy Technology Data Exchange (ETDEWEB)

    Lee, H. S.; Kuk, I. H.; Chung, H.; Paek, S. W.; Kang, H. S

    1999-08-01

    8 MCi of tritium a year will be produced after wolsong TRF is in operation. The metal hydride form is one of useful tritium storage. The metals in use for metal hydride are uranium, titanium, etc., however uranium is limited to use by regulation, and titanium is relatively costly. Both metals are not produced in country but whole amount is imported. On the other hand 2,000kg of zircaloy scrap is produced by CANDU nuclear fuel fabrication process, which is also useful for hydrogen storage. The purpose of this study is to evaluation of hydrogen absorption capacity for zircaloy scrap that is produced as waste by CANDU nuclear fuel fabrication process. The sample evacuated for an hour at 1000 deg C. The strip showed higher capacity : 0.7 at 25 deg C, 2.0 at 200 deg C, 2.0 at 200 deg C, 2.0 at 400 deg C, respectively. The H/M values for commercial zircaloy sponge were 2.0 at 25 deg C and 2.0 at 400 deg C.

  17. Hydrogen isotope storage in zircaloy scrap

    International Nuclear Information System (INIS)

    Lee, H. S.; Kuk, I. H.; Chung, H.; Paek, S. W.; Kang, H. S.

    1999-08-01

    8 MCi of tritium a year will be produced after wolsong TRF is in operation. The metal hydride form is one of useful tritium storage. The metals in use for metal hydride are uranium, titanium, etc., however uranium is limited to use by regulation, and titanium is relatively costly. Both metals are not produced in country but whole amount is imported. On the other hand 2,000kg of zircaloy scrap is produced by CANDU nuclear fuel fabrication process, which is also useful for hydrogen storage. The purpose of this study is to evaluation of hydrogen absorption capacity for zircaloy scrap that is produced as waste by CANDU nuclear fuel fabrication process. The sample evacuated for an hour at 1000 deg C. The strip showed higher capacity : 0.7 at 25 deg C, 2.0 at 200 deg C, 2.0 at 200 deg C, 2.0 at 400 deg C, respectively. The H/M values for commercial zircaloy sponge were 2.0 at 25 deg C and 2.0 at 400 deg C

  18. Remelting of Aluminium by Continuous Submersion of Rolled Scrap

    Energy Technology Data Exchange (ETDEWEB)

    Farner, Snorre

    2000-12-01

    When remelting aluminium scrap, metal losses due to dross generation is a common problem. Reduction of these losses will give substantial economic and environmental benefits. Dross is generated when aluminium metal oxidizes and films of oxide envelope molten metal. When a cold metal object is immersed in a melt, the heat of the melt around this is transferred so rapidly into the object that a shell of melt often solidifies to the surface of the object. When scrap with low bulk density is charged to a melt, solidification of melt on the cold scrap prevents melt from entering the cavities in the bulk of the scrap, and the bulk density remains low. Thus the scrap tends to float on the melt surface. Submersion of this scrap is important to avoid oxidation and subsequent dross generation. One solution to this is to roll scrap to a strip and feed it into the melt. This system has been examined by studying feeding of a continuous, thin aluminium plate into molten aluminium. Also, the effect of lacquer was considered, as well as feeding the plate into a launder with melt flowing along the surface of the plate. An analytical, one-dimensional, steady-state model has been developed to describe the melting and the melting mechanisms. It is based on a shell solidifying on the plate surface and a gap introducing a thermal resistance 1/h{sub g} between the shell and the plate. The thermal resistance 1/h{sub l} of the boundary layer of the melt is included. Depending on these resistances, the initial temperature of the plate and the melt temperature, a shell will form, and the plate will penetrate a distance P into the melt before it melts away. An experimental apparatus was designed and constructed to feed aluminium plate from a coil into a melt bath at a specified velocity. The plate could be withdrawn rapidly to ''freeze'' the situation like it was below the melt surface. The penetration depth P of the plate could be measured and shell formation observed

  19. Incidence of hemoglobinopathies and thalassemias in Northern Alberta. Establishment of reference intervals for HbF and HbA2.

    Science.gov (United States)

    Rodriguez-Capote, Karina; Higgins, Trefor N

    2015-07-01

    The aims of this study were to identify the incidence of hemoglobinopathies and thalassemias in Northern Alberta and calculate the reference intervals (RI) for hemoglobin (Hb) HbF and HbA2. A retrospective ad-hoc analysis of the structural Hb variants and thalassemias identified on patients who had a hemoglobinopathy/thalassemia investigation performed between February 1 to December 31, 2013. Results were extracted from the Laboratory Information System. Statistical analysis was performed using MedCalc® version 11.4.2.0 for Windows software. 6616 hemoglobinopathy/thalassemia investigations and HbS screens were physician requested and 602 Hb variants were fortuitously found during HbA1c analysis. 3438 were interpreted as "normal" and 532 were classified as iron deficient. 3306 individuals, with age ranging from 3 to 92 years were included in the RI calculation. HbA2 RI was 2.3% to 3.4% and HbF 0.0% to 1.8%. 524 and 423 α and β thalassemia traits respectively were identified. Additionally ten δβ thalassemia traits and twelve cases of HbH disease were identified. Regarding hemoglobinopathies, 7% were classified as α-chain variants and 93% as β-chain variants with HbS (46%), HbE (16%), HbD Punjab (8%) and HbC (7%) traits being the most prevalent. We also documented 20 homozygous hemoglobinopathies and 36 compound/double heterozygous hemoglobinopathies. A wide diversity of hemoglobinopathies is found in the Northern Alberta population, 80% of the hemoglobinopathies were found as a reflex to HbA1c testing. Reference intervals for HbF and HbA2 were established. Copyright © 2015 The Canadian Society of Clinical Chemists. Published by Elsevier Inc. All rights reserved.

  20. Registration of Food Barley (Hordeum vulgare L.) Variety HB 1307 ...

    African Journals Online (AJOL)

    Six-rowed food type barley, HB 1307, was developed by Holetta Agricultural Research Center (HARC) from a cross between a landrace line and exotic germplasm (Awra gebs-1 x IBON93/91) and released in 2006 for mid and high altitude areas. The three consecutive years\\' (2002-2004) tests proved its superiority in grain ...

  1. Active solution of homography for pavement crack recovery with four laser lines.

    Science.gov (United States)

    Xu, Guan; Chen, Fang; Wu, Guangwei; Li, Xiaotao

    2018-05-08

    An active solution method of the homography, which is derived from four laser lines, is proposed to recover the pavement cracks captured by the camera to the real-dimension cracks in the pavement plane. The measurement system, including a camera and four laser projectors, captures the projection laser points on the 2D reference in different positions. The projection laser points are reconstructed in the camera coordinate system. Then, the laser lines are initialized and optimized by the projection laser points. Moreover, the plane-indicated Plücker matrices of the optimized laser lines are employed to model the laser projection points of the laser lines on the pavement. The image-pavement homography is actively determined by the solutions of the perpendicular feet of the projection laser points. The pavement cracks are recovered by the active solution of homography in the experiments. The recovery accuracy of the active solution method is verified by the 2D dimension-known reference. The test case with the measurement distance of 700 mm and the relative angle of 8° achieves the smallest recovery error of 0.78 mm in the experimental investigations, which indicates the application potentials in the vision-based pavement inspection.

  2. Spinal Hb9::Cre-derived excitatory interneurons contribute to rhythm generation in the mouse.

    Science.gov (United States)

    Caldeira, Vanessa; Dougherty, Kimberly J; Borgius, Lotta; Kiehn, Ole

    2017-01-27

    Rhythm generating neurons are thought to be ipsilaterally-projecting excitatory neurons in the thoracolumbar mammalian spinal cord. Recently, a subset of Shox2 interneurons (Shox2 non-V2a INs) was found to fulfill these criteria and make up a fraction of the rhythm-generating population. Here we use Hb9::Cre mice to genetically manipulate Hb9::Cre-derived excitatory interneurons (INs) in order to determine the role of these INs in rhythm generation. We demonstrate that this line captures a consistent population of spinal INs which is mixed with respect to neurotransmitter phenotype and progenitor domain, but does not overlap with the Shox2 non-V2a population. We also show that Hb9::Cre-derived INs include the comparatively small medial population of INs which continues to express Hb9 postnatally. When excitatory neurotransmission is selectively blocked by deleting Vglut2 from Hb9::Cre-derived INs, there is no difference in left-right and/or flexor-extensor phasing between these cords and controls, suggesting that excitatory Hb9::Cre-derived INs do not affect pattern generation. In contrast, the frequencies of locomotor activity are significantly lower in cords from Hb9::Cre-Vglut2 Δ/Δ mice than in cords from controls. Collectively, our findings indicate that excitatory Hb9::Cre-derived INs constitute a distinct population of neurons that participates in the rhythm generating kernel for spinal locomotion.

  3. Detection of compound heterozygous of hb constant spring and hb q-Thailand by capillary electrophoresis and high performance liquid chromatography.

    Science.gov (United States)

    Pornprasert, Sakorn; Punyamung, Manoo

    2015-06-01

    A capillary electrophoresis (CE) has proven to be superior to a high performance liquid chromatography (HPLC) in the detection of hemoglobin Constant Spring (Hb CS). Thus the aim of this study was to analyze the efficacy of CE and HPLC for the detection of Hb CS in samples with compound heterozygous of Hb CS and Hb Q-Thailand. Hemoglobin analysis was performed in blood samples of 2 patients with compound heterozygous of Hb CS and Hb Q-Thailand by using HPLC and CE. The HPLC chromatogram and CE electrophoregram of the two techniques were compared. Hb CS was not found on HPLC chromatogram while Hb QA2 (α2 (QT)δ2), a derivative of Hb Q-Thailand, was presented at the retention time of 4.70-4.80 min and it was close to the retention time of Hb CS. On CE electrophoregram, Hb CS was presented at zone 2 (Z2) and it was distinctly separated from Hb QA2 which was presented at Z1. Therefore, CE was more efficient to the HPLC for diagnosis of compound heterozygous of Hb CS and Hb Q-Thailand.

  4. Economic and policy instrument analyses in support of the scrap tire recycling program in Taiwan.

    Science.gov (United States)

    Chang, Ni-Bin

    2008-02-01

    Understanding the cost-effectiveness and the role of economic and policy instruments, such as the combined product tax-recycling subsidy scheme or a tradable permit, for scrap tire recycling has been of crucial importance in a market-oriented environmental management system. Promoting product (tire) stewardship on one hand and improving incentive-based recycling policy on the other hand requires a comprehensive analysis of the interfaces and interactions in the nexus of economic impacts, environmental management, environmental valuation, and cost-benefit analysis. This paper presents an assessment of the interfaces and interactions between the implementation of policy instruments and its associated economic evaluation for sustaining a scrap tire recycling program in Taiwan during the era of the strong economic growth of the late 1990s. It begins with an introduction of the management of the co-evolution between technology metrics of scrap tire recycling and organizational changes for meeting the managerial goals island-wide during the 1990s. The database collected and used for such analysis covers 17 major tire recycling firms and 10 major tire manufacturers at that time. With estimates of scrap tire generation and possible scale of subsidy with respect to differing tire recycling technologies applied, economic analysis eventually leads to identify the associated levels of product tax with respect to various sizes of new tires. It particularly demonstrates a broad perspective of how an integrated econometric and engineering economic analysis can be conducted to assist in implementing policy instruments for scrap tire management. Research findings indicate that different subsidy settings for collection, processing, and end use of scrap tires should be configured to ameliorate the overall managerial effectiveness. Removing the existing boundaries between designated service districts could strengthen the competitiveness of scrap tires recycling industry, helping to

  5. HB Puerta del Sol [HBA1:c.148A>C], HB Valdecilla [HBA2:c.3G>T], HB Gran Vía [HBA2:c.98T>G], HB Macarena [HBA2:c.358C>T] and HB El Retiro [HBA2:c.364_366dupGTG]: description of five new hemoglobinopathies.

    Science.gov (United States)

    de la Fuente-Gonzalo, Félix; Nieto, Jorge M; Velasco, Diego; Cela, Elena; Pérez, Germán; Fernández-Teijeiro, Ana; Escudero, Antonio; Villegas, Ana; González-Fernández, Fernando A; Ropero, Paloma

    2016-04-01

    Structural hemoglobinopathies do not usually have a clinical impact, but they can interfere with the analytical determination of some parameters, such as the glycated hemoglobin in diabetic patients. Thalassemias represent a serious health problem in areas where their incidence is high. The defects in the post-translational modifications produce hyper-unstable hemoglobin that is not detected by most of electrophoretic or chromatographic methods that are available so far. We studied seven patients who belong to six unrelated families. The first two families were studied because they had peak abnormal hemoglobin (Hb) during routine analytical assays. The other four families were studied because they had microcytosis and hypochromia with normal HbA2 and HbF without iron deficiency. HbA2 and F quantification and abnormal Hb separation were performed by chromatographic and electrophoretic methods. The molecular characterization was performed using specific sequencing. The Hb Puerta del Sol presents electrophoretic mobility and elution in HPLC that is different from HbA and similar to HbS. The electrophoretic and chromatographic profiles of the four other variants are normal and do not show any anomalies, and their identification was only possible with sequencing. Some variants, such as Hb Valdecilla, Hb Gran Vía, Hb Macarena and Hb El Retiro, have significant clinical impact when they are associated with other forms of α-thalassemia, which could lead to more serious forms of this group of pathologies as for HbH disease. Therefore, it is important to maintain an adequate program for screening these diseases in countries where the prevalence is high to prevent the occurrence of severe forms.

  6. Iron deficiency anemia interfering the diagnosis of compound heterozygosity for Hb constant spring and Hb Paksé: The first case report.

    Science.gov (United States)

    Chiasakul, Thita; Uaprasert, Noppacharn

    2018-01-01

    Diagnosis of thalassemia or hemoglobinopathy concomitant with iron deficiency anemia (IDA) is challenging. We report a case of 43-year-old female whose diagnosis of compound heterozygosity for hemoglobin Constant Spring (HbCS) and Hb Paksé became apparent after the treatment of IDA. Prior to treatment, Hb analysis using isoelectric focusing (IEF) showed HbA 95.6%, HbA 2 2.7%, and HbCS 1.7% compatible with heterozygous HbCS. After 4 months of oral iron therapy resulting in an improved Hb level, her HbCS level was substantially increased to 8.7% on IEF suggesting homozygous HbCS. Subsequent DNA analysis using multiplex amplification refractory mutation system analysis revealed compound heterozygosity for HbCS and Hb Paksé. This case demonstrated that IDA can significantly reduce HbCS/Hb Paksé levels and probably mask the diagnosis of homozygous HbCS, homozygous Hb Paksé or the compound heterozygosity for both hemoglobinopathies by hemoblogin analysis. The test should be repeated after resolution of IDA, or molecular testing should be performed to confirm the diagnosis. © 2017 Wiley Periodicals, Inc.

  7. A Longitudinal Analysis of the Influence of a Peer Run Warm Line Phone Service on Psychiatric Recovery.

    Science.gov (United States)

    Dalgin, Rebecca Spirito; Dalgin, M Halim; Metzger, Scott J

    2018-05-01

    This article focuses on the impact of a peer run warm line as part of the psychiatric recovery process. It utilized data including the Recovery Assessment Scale, community integration measures and crisis service usage. Longitudinal statistical analysis was completed on 48 sets of data from 2011, 2012, and 2013. Although no statistically significant differences were observed for the RAS score, community integration data showed increases in visits to primary care doctors, leisure/recreation activities and socialization with others. This study highlights the complexity of psychiatric recovery and that nonclinical peer services like peer run warm lines may be critical to the process.

  8. Advanced technologies for decontamination and conversion of scrap metals

    International Nuclear Information System (INIS)

    Muth, T.R.; Moore, J.; Olson, D.; Mishra, B.

    1994-01-01

    Recycle of radioactive scrap metals (RSM) from decommissioning of DOE uranium enrichment and nuclear weapons manufacturing facilities is mandatory to recapture the value of these metals and avoid the high cost of disposal by burial. The scrap metals conversion project detailed below focuses on the contaminated nickel associated with the gaseous diffusion plants. Stainless steel can be produced in MSC's vacuum induction melting process (VIM) to the S30400 specification using nickel as an alloy constituent. Further the case alloy can be rolled in MSC's rolling mill to the mechanical property specification for S30400 demonstrating the capability to manufacture the contaminated nickel into valuable end products at a facility licensed to handle radioactive materials. Bulk removal of Technetium from scrap nickel is theoretically possible in a reasonable length of time with the high calcium fluoride flux, however the need for the high temperature creates a practical problem due to flux volatility. Bulk decontamination is possible and perhaps more desirable if nickel is alloyed with copper to lower the melting point of the alloy allowing the use of the high calcium fluoride flux. Slag decontamination processes have been suggested which have been proven technically viable at the Colorado School of Mines

  9. Vitrification for stability of scrap and residue

    Energy Technology Data Exchange (ETDEWEB)

    Forsberg, C.W. [Oak Ridge National Lab., TN (United States)

    1996-05-01

    A conference breakout discussion was held on the subject of vitrification for stabilization of plutonium scrap and residue. This was one of four such sessions held within the vitrification workshop for participants to discuss specific subjects in further detail. The questions and issues were defined by the participants.

  10. Preparation of High-purity Indium Oxalate Salt from Indium Scrap by Organic Acids

    International Nuclear Information System (INIS)

    Koo, Su-Jin; Ju, Chang-Sik

    2013-01-01

    Effect of organic acid on the preparation of indium-oxalate salt from indium scraps generated from ITO glass manufacturing process was studied. Effects of parameters, such as type and concentration of organic acids, pH of reactant, temperature, reaction time on indium-oxalate salt preparation were examined. The impurity removal efficiency was similar for both oxalic acid and citric acid, but citric acid did not make organic acid salt with indium. The optimum conditions were 1.5 M oxalic acid, pH 7, 80 .deg. C, and 6 hours. On the other hand, the recoveries increased with pH, but the purity decreased. The indium-oxalate salt purity prepared by two cycles was 99.995% (4N5). The indium-oxalate salt could be converted to indium oxide and indium metal by substitution reaction and calcination

  11. Cerebral Hemodynamics and Executive Function During Exercise and Recovery in Normobaric Hypoxia.

    Science.gov (United States)

    Stavres, Jon; Gerhart, Hayden D; Kim, Jung-Hyun; Glickman, Ellen L; Seo, Yongsuk

    2017-10-01

    Hypoxia and exercise each exhibit opposing effects on executive function, and the mechanisms for this are not entirely clear. This study examined the influence of cerebral oxygenation and perfusion on executive function during exercise and recovery in normobaric hypoxia (NH) and normoxia (N). There were 18 subjects who completed cycling trials in NH (12.5% FIo2) and N (20.93% FIo2). Right prefrontal cortex (PFC) oxyhemoglobin (O2Hb) and middle cerebral artery blood velocity (MCAbv) were collected during executive function challenges [mathematical processing and running memory continuous performance task (RMCPT)] at baseline, following 30 min of acclimation, during 20 min of cycling (60% Vo2max), and at 1, 15, 30, and 45 min following exercise. Results indicated effects of time for Math, RMCPT, and O2Hb; but not for MCAbv. Results also indicated effects of condition for O2Hb. Math scores were improved by 8.0% during exercise and remained elevated at 30 min of recovery (12.5%), RMCPT scores significantly improved at all time points (7.5-11.9%), and O2Hb increased by 662.2% and 440.9% during exercise in N and NH, respectively, and remained elevated through 15 min of recovery in both conditions. These results support the influence of PFC oxygenation and perfusion on executive function during exercise and recovery in N and NH.Stavres J, Gerhart HD, Kim J-H, Glickman EL, Seo Y. Cerebral hemodynamics and executive function during exercise and recovery in normobaric hypoxia. Aerosp Med Hum Perform 2017; 88(10):911-917.

  12. Scrap is no crap

    DEFF Research Database (Denmark)

    Wenzel, Henrik

    2009-01-01

    Scrap is good business for the environment. When we recycle metal - meaning to collect, sort and melt it down - we emit much less CO2 than when we extract metal from the ground. The environmental benefit applies to all metals and is gained every time we recycle them. That is a positive message in...... in a world where we search for methods to reduce our CO2 emission. And the environmental potential is big: There are no upper limits for how many times we can recycle metals, which makes recycling an important part of the fight against global warming....

  13. Progress toward uranium scrap recycling via electron beam cold hearth refining

    International Nuclear Information System (INIS)

    McKoon, R.H.

    1994-01-01

    A 250 kW electron beam cold hearth refining (EBCHR) melt furnace at Lawrence Livermore National Laboratory (LLNL) has been in operation for over a year producing 5.5 in.-diameter ingots of various uranium alloys. Production of in-specification uranium-6%-niobium (U-6Nb) alloy ingots has been demonstrated using Virgin feedstock. A vibratory scrap feeder has been installed on the system and the ability to recycle chopped U-6Nb scrap has been established. A preliminary comparison of vacuum arc remelted (VAR) and electron beam (EB) melted product is presented

  14. Progress toward uranium scrap recycling via Electron Cold Hearth Refining (EBCHR)

    International Nuclear Information System (INIS)

    McKoon, R.H.

    1994-01-01

    A 250 kW electron beam cold hearth refining (EBCHR) melt furnace at Lawrence Livermore National Laboratory (LLNL) has been in operation for over a year producing 5.5 in.-diameter ingots of various uranium alloys. Production of in-specification uranium-6% - niobium (U-6Nb) alloy ingots has been demonstrated using virgin feedstock. A vibratory scrap feeder has been installed on the system and the ability to recycle chopped U-6Nb scrap has been established. A preliminary comparison of vacuum arc remelted (VAR) and electron beam (EB) melted product is presented

  15. The reuse of scrap and decontamination waste water from decommissioning

    International Nuclear Information System (INIS)

    Deng Junxian; Li Xin; Xie Xiaolong

    2010-01-01

    Huge amount of radioactive scrap with low activity will be generated from reactor decommissioning; the decontamination is concentrated in the surface layer of the scrap. The decontaminated substance can be removed by high pressure water jet to appear the base metal and to reuse the metal. Big amount of radioactive waste water will be generated by this decontamination technology; the radioactive of the waste water is mainly caused by the solid particle from decontamination. To remove the solid particle as clean as possible, the waste water can be reused. Different possible technology to remove the solid particle from the water had been investigated, such as the gravity deposit separation, the filtration and the centrifugal separation etc. The centrifugal separation technology is selected; it includes the hydraulic vortex, the centrifugal filtration and the centrifugal deposit. After the cost benefit analysis at last the centrifugal deposit used butterfly type separator is selected. To reuse the waste water the fresh water consumption and the cost for waste water treatment can be reduced. To reuse the radioactive scrap and the waste water from decommissioning will minimize the radioactive waste. (authors)

  16. Feasibility study on the St. Petersburg City heat and electric cogeneration plant No.2, etc. scrap and build project

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing greenhouse effect gas emissions in line with the Joint Implementation, a survey was made of the scrap and build project for the superannuated Central Heat Power Station in St. Petersburg City. The survey team visited the relevant sites twice during 1999. The team drafted an improvement plan afterwards and presented it to the Russian counterpart, LENENEGRO. Based on the discussions with LENENEGRO, it was determined that the proposed combined cycle cogeneration plant would contain three 67MW-class gas turbines, three heat recovery steam generators and one back pressure turbine to achieve the generation capacity of approximately 200MW and heat supply capacity of 200G cal/hr. The total investment required for this project is about 140 million dollars. The term of the construction work is estimated at 36 months. It is estimated that the implementation of the project will reduce 1,481,979 tons of CO2 per year, or a total of 40,013,434 tons in 27 years after the commencement of operation. In addition, the terminal power generation efficiency will be improved from the current 18.68% to 41%, which leads to an annual fuel saving of 546,301 tons of crude oil or its equivalent. (NEDO)

  17. Recycling and recovery routes of plastic solid waste (PSW): A review

    International Nuclear Information System (INIS)

    Al-Salem, S.M.; Lettieri, P.; Baeyens, J.

    2009-01-01

    Plastic solid waste (PSW) presents challenges and opportunities to societies regardless of their sustainability awareness and technological advances. In this paper, recent progress in the recycling and recovery of PSW is reviewed. A special emphasis is paid on waste generated from polyolefinic sources, which makes up a great percentage of our daily single-life cycle plastic products. The four routes of PSW treatment are detailed and discussed covering primary (re-extrusion), secondary (mechanical), tertiary (chemical) and quaternary (energy recovery) schemes and technologies. Primary recycling, which involves the re-introduction of clean scrap of single polymer to the extrusion cycle in order to produce products of the similar material, is commonly applied in the processing line itself but rarely applied among recyclers, as recycling materials rarely possess the required quality. The various waste products, consisting of either end-of-life or production (scrap) waste, are the feedstock of secondary techniques, thereby generally reduced in size to a more desirable shape and form, such as pellets, flakes or powders, depending on the source, shape and usability. Tertiary treatment schemes have contributed greatly to the recycling status of PSW in recent years. Advanced thermo-chemical treatment methods cover a wide range of technologies and produce either fuels or petrochemical feedstock. Nowadays, non-catalytic thermal cracking (thermolysis) is receiving renewed attention, due to the fact of added value on a crude oil barrel and its very valuable yielded products. But a fact remains that advanced thermo-chemical recycling of PSW (namely polyolefins) still lacks the proper design and kinetic background to target certain desired products and/or chemicals. Energy recovery was found to be an attainable solution to PSW in general and municipal solid waste (MSW) in particular. The amount of energy produced in kilns and reactors applied in this route is sufficiently

  18. Recycling and processing of several typical crosslinked polymer scraps with enhanced mechanical properties based on solid-state mechanochemical milling

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Canhui; Zhang, Xinxing; Zhang, Wei [State Key Laboratory of Polymer Materials Engineering, Polymer Research Institute, Sichuan University, Chengdu 610065 (China)

    2015-05-22

    The partially devulcanization or de-crosslinking of ground tire rubber (GTR), post-vulcanized fluororubber scraps and crosslinked polyethylene from cable scraps through high-shear mechanochemical milling (HSMM) was conducted by a modified solid-state mechanochemical reactor. The results indicated that the HSMM treated crosslinked polymer scraps can be reprocessed as virgin rubbers or thermoplastics to produce materials with high performance. The foamed composites of low density polyethylene/GTR and the blend of post-vulcanized flurorubber (FKM) with polyacrylate rubber (ACM) with better processability and mechanical properties were obtained. The morphology observation showed that the dispersion and compatibility between de-crosslinked polymer scraps and matrix were enhanced. The results demonstrated that HSMM is a feasible alternative technology for recycling post-vulcanized or crosslinked polymer scraps.

  19. Recycling and processing of several typical crosslinked polymer scraps with enhanced mechanical properties based on solid-state mechanochemical milling

    Science.gov (United States)

    Lu, Canhui; Zhang, Xinxing; Zhang, Wei

    2015-05-01

    The partially devulcanization or de-crosslinking of ground tire rubber (GTR), post-vulcanized fluororubber scraps and crosslinked polyethylene from cable scraps through high-shear mechanochemical milling (HSMM) was conducted by a modified solid-state mechanochemical reactor. The results indicated that the HSMM treated crosslinked polymer scraps can be reprocessed as virgin rubbers or thermoplastics to produce materials with high performance. The foamed composites of low density polyethylene/GTR and the blend of post-vulcanized flurorubber (FKM) with polyacrylate rubber (ACM) with better processability and mechanical properties were obtained. The morphology observation showed that the dispersion and compatibility between de-crosslinked polymer scraps and matrix were enhanced. The results demonstrated that HSMM is a feasible alternative technology for recycling post-vulcanized or crosslinked polymer scraps.

  20. Recycling and processing of several typical crosslinked polymer scraps with enhanced mechanical properties based on solid-state mechanochemical milling

    International Nuclear Information System (INIS)

    Lu, Canhui; Zhang, Xinxing; Zhang, Wei

    2015-01-01

    The partially devulcanization or de-crosslinking of ground tire rubber (GTR), post-vulcanized fluororubber scraps and crosslinked polyethylene from cable scraps through high-shear mechanochemical milling (HSMM) was conducted by a modified solid-state mechanochemical reactor. The results indicated that the HSMM treated crosslinked polymer scraps can be reprocessed as virgin rubbers or thermoplastics to produce materials with high performance. The foamed composites of low density polyethylene/GTR and the blend of post-vulcanized flurorubber (FKM) with polyacrylate rubber (ACM) with better processability and mechanical properties were obtained. The morphology observation showed that the dispersion and compatibility between de-crosslinked polymer scraps and matrix were enhanced. The results demonstrated that HSMM is a feasible alternative technology for recycling post-vulcanized or crosslinked polymer scraps

  1. Glutathione Redox System in β-Thalassemia/Hb E Patients

    Directory of Open Access Journals (Sweden)

    Ruchaneekorn W. Kalpravidh

    2013-01-01

    Full Text Available β-thalassemia/Hb E is known to cause oxidative stress induced by iron overload. The glutathione system is the major endogenous antioxidant that protects animal cells from oxidative damage. This study aimed to determine the effect of disease state and splenectomy on redox status expressed by whole blood glutathione (GSH/glutathione disulfide (GSSG and also to evaluate glutathione-related responses to oxidation in β-thalassemia/Hb E patients. Twenty-seven normal subjects and 25 β-thalassemia/Hb E patients were recruited and blood was collected. The GSH/GSSG ratio, activities of glutathione-related enzymes, hematological parameters, and serum ferritin levels were determined in individuals. Patients had high iron-induced oxidative stress, shown as significantly increased serum ferritin, a decreased GSH/GSSG ratio, and increased activities of glutathione-related enzymes. Splenectomy increased serum ferritin levels and decreased GSH levels concomitant with unchanged glutathione-related enzyme activities. The redox ratio had a positive correlation with hemoglobin levels and negative correlation with levels of serum ferritin. The glutathione system may be the body’s first-line defense used against oxidative stress and to maintain redox homeostasis in thalassemic patients based on the significant correlations between the GSH/GSSH ratio and degree of anemia or body iron stores.

  2. Spinal Hb9::Cre-derived excitatory interneurons contribute to rhythm generation in the mouse

    DEFF Research Database (Denmark)

    Caldeira, Vanessa; Dougherty, Kimberly J.; Borgius, Lotta

    2017-01-01

    Rhythm generating neurons are thought to be ipsilaterally-projecting excitatory neurons in the thoracolumbar mammalian spinal cord. Recently, a subset of Shox2 interneurons (Shox2 non-V2a INs) was found to fulfill these criteria and make up a fraction of the rhythm-generating population. Here we...... than in cords from controls. Collectively, our findings indicate that excitatory Hb9::Cre-derived INs constitute a distinct population of neurons that participates in the rhythm generating kernel for spinal locomotion....... use Hb9::Cre mice to genetically manipulate Hb9::Cre-derived excitatory interneurons (INs) in order to determine the role of these INs in rhythm generation. We demonstrate that this line captures a consistent population of spinal INs which is mixed with respect to neurotransmitter phenotype...

  3. Relationship between Hb and HbA1c in Japanese adults: an analysis of the 2009 Japan Society of Ningen Dock database.

    Science.gov (United States)

    Takahashi, Eiko; Moriyama, Kengo; Yamakado, Minoru

    2014-06-01

    We investigated the effect of Hb on HbA1c levels in 265,427 Japanese individuals. The divergence between fasting plasma glucose (FPG) and HbA1c levels increased with lower Hb, resulting in HbA1c levels that were higher in relation to than the FPG levels. Similarly, the correlation between FPG and HbA1c levels, stratified by Hb, weakened as Hb decreased. Copyright © 2014 Elsevier Ireland Ltd. All rights reserved.

  4. Phenotypic Diversity of Sickle Cell Disease in Patients with a Double Heterozygosity for Hb S and Hb D-Punjab.

    Science.gov (United States)

    Torres, Lidiane S; Okumura, Jéssika V; Belini-Júnior, Édis; Oliveira, Renan G; Nascimento, Patrícia P; Silva, Danilo G H; Lobo, Clarisse L C; Oliani, Sonia M; Bonini-Domingos, Claudia R

    2016-09-01

    Phenotypic heterogeneity for sickle cell disease is associated to several genetic factors such as genotype for sickle cell disease, β-globin gene cluster haplotypes and Hb F levels. The coinheritance of Hb S (HBB: c.20A > T) and Hb D-Punjab (HBB: c.364G > C) results in a double heterozygosity, which constitutes one of the genotypic causes of sickle cell disease. This study aimed to assess the phenotypic diversity of sickle cell disease presented by carriers of the Hb S/Hb D-Punjab genotype and the Bantu [- + - - - -] haplotype. We evaluated medical records from 12 patients with sickle cell disease whose Hb S/Hb D-Punjab genotype and Bantu haplotype were confirmed by molecular analysis. Hb S and Hb D-Punjab levels were quantified by chromatographic analysis. Mean concentrations of Hb S and Hb D-Punjab were 44.8 ± 2.3% and 43.3 ± 1.8%, respectively. Painful crises were present in eight (66.7%) patients evaluated, representing the most common clinical event. Acute chest syndrome (ACS) was the second most prevalent manifestation, occurring in two individuals (16.7%). Three patients were asymptomatic, while another two exhibited greater diversity of severe clinical manifestations. Medical records here analyzed reported a significant clinical diversity in sickle cell disease ranging from the absence of symptoms to wide phenotypic variety. The sickle cell disease genotype, Bantu haplotype and hemoglobin (Hb) levels did not influence the clinical diversity. Thus, we concluded that the phenotypic variation in sickle cell disease was present within a specific genotype for disease regardless of the β-globin gene cluster haplotypes.

  5. First Case of a Compound Heterozygosity for Two Nondeletional α-Thalassemia mutations, Hb Constant Spring and Hb Quong Sze.

    Science.gov (United States)

    Zhou, Jian-Ying; Yan, Jin-Mei; Li, Jian; Li, Dong-Zhi

    2016-06-01

    Nondeletional α-thalassemia (α-thal) is the result of point mutations in critical regions of the α-globin genes, affecting mRNA processing, mRNA translation, or α-globin stability. Hb Constant Spring (Hb CS, HBA2: c.427T > C) is the most common nondeletional α-thal that results from a nucleotide substitution at the termination codon of the α2-globin gene. Hb Quong Sze (Hb QS, HBA2: c.377T > C) is another nondeletional α-thal in South China with the missense mutation at codon 125 of the α2-globin gene making this hemoglobin (Hb) variant highly unstable. Although homozygosity for Hb CS (α(CS)α/α(CS)α) or Hb QS (α(QS)α/α(QS)α) has been reported, clinical pictures vary from severe hemolysis that developed early in life to only mild anemia, no clinical phenotypic data of compound heterozygosity for Hb CS/Hb QS (α(CS)α/α(QS)α) has been described. In this report we describe an adult case with such a compound heterozygosity who presented with a mild α-thal.

  6. Comparative haematological parameters of HbAA and HbAS genotype children infected with Plasmodium falciparum malaria in Yemen.

    Science.gov (United States)

    Albiti, Anisa H; Nsiah, Kwabena

    2014-04-01

    Sickle haemoglobin (HbS) is known to offer considerable protection against falciparum malaria. However, the mechanism of protection is not yet completely understood. In this study, we investigate how the presence of the sickle cell trait affects the haematological profile of AS persons with malaria, in comparison with similarly infected persons with HbAA. This study is based on the hypothesis that the sickle cell trait plays a protective role against malaria. Children from an endemic malaria transmission area in Yemen were enrolled in this study. Hematological parameters were estimated using manual methods, the percentage of parasite density on stained thin smear was calculated, haemoglobin genotypes were determined on paper electrophoresis, ferritin was measured using enzyme-linked immunosorbent assay, serum iron and TIBC were assayed using spectrophotometer, transferrin saturation index was calculated by dividing serum iron by TIBC and expressing the result as a percentage. Haematological parameters were compared in HbAA- and HbAS-infected children. Falciparum malaria parasitaemia was confirmed in the blood smears of 62 children, 44 (55.7%) of AA and 18 (37.5%) AS, so there was higher prevalence in HbAA children (P = 0.047). Parasite density was lower in HbAS- than HbAA-infected children (P = 0.003). Anaemia was prominent in malaria-infected children, with high proportions of moderate and severe forms in HbAA (P = 0.001). The mean levels of haemoglobin, packed cell volume, reticulocyte count, platelets count, lymphocytes, eosinophils, and serum iron were significantly lower while total leukocytes, immature granulocytes, monocytes, erythrocyte sedimentation rate, transferrin saturation, and serum ferritin were significantly higher in HbAA-infected children than HbAS-infected children. Infection with Plasmodium falciparum malaria caused more significant haematological alterations of HbAA children than HbAS. This study supports the observation that sickle cell trait

  7. Automobile scrap regulation. Give-away presents. Polluting cars and trade-in for cleaner cars

    International Nuclear Information System (INIS)

    Annema, J.A.

    2010-01-01

    A scrap regulation for old vehicles has been in place in the Netherlands for almost one year now. Has it been an effective instrument? What are the societal costs and benefits? Is it a fair regulation? Was it a good idea to introduce the car scrap regulation? The answer to all these questions is: doubtful. [nl

  8. Aluminium recovery from waste incineration bottom ash, and its oxidation level.

    Science.gov (United States)

    Biganzoli, Laura; Grosso, Mario

    2013-09-01

    The recovery of aluminium (Al) scraps from waste incineration bottom ash is becoming a common practice in waste management. However, during the incineration process, Al in the waste undergoes oxidation processes that reduce its recycling potential. This article investigates the behaviour of Al scraps in the furnace of two selected grate-fired waste-to-energy plants and the amount recoverable from the bottom ash. About 21-23% of the Al fed to the furnace with the residual waste was recovered and potentially recycled from the bottom ash. Out of this amount, 76-87% was found in the bottom ash fraction above 5 mm and thus can be recovered with standard eddy current separation technology. These values depend on the characteristics and the mechanical strength of the Al items in the residual waste. Considering Al packaging materials, about 81% of the Al in cans can be recovered from the bottom ash as an ingot, but this amount decreases to 51% for trays, 27% for a mix of aluminium and poly-laminated foils and 47% for paper-laminated foils. This shows that the recovery of Al from the incineration residues increases proportionally to the thickness of the packaging.

  9. Recycling decontaminated scrap metal from the nuclear industry

    International Nuclear Information System (INIS)

    Bordas, F.

    2000-01-01

    The Commissariat a l'Energie Atomique (CEA) has set up a pilot program for recycling decontaminated scrap metal. In decommissioning its enriched uranium production facilities at Pierrelatte, the CEA has accumulated some 700 metric tons of scrap metal from dismantled uranium hexafluoride transport containers. The containers were decontaminated by SOCATRI at the Tricastin site, then cut up and recycled by a steelmaker. The project was submitted to the Ionizing Radiation Protection Office, the Nuclear Facilities Safety Division and the Regional Directorate for Industry, Research and Environmental Protection for approval. It was also submitted to the Ministry of Industry's Nuclear Information and Safety Council and to the Permanent Secretariat for Industrial Pollution Problems (an informational group chaired by the Prefect of the Provence Alpes-Cote d Azur region and including representatives of local and regional authorities, associations, elected officials and the media). The permit was granted for this program under the terms of a prefectorial decree stipulating additional requirements for the steelmaker, and contingent on the demonstration of full control over the operations, demonstrated traceability and the absence of any significant harmful effects. The key elements of this demonstration include the choice of operators, identification of the objects, itemization of the operations, discrimination of operators, the contractual framework of the operations, the signature of agreements by the CEA with SOCATRI and with the steelmaker, documentary monitoring of the operations, contradictory inspections and measurements, second-level inspection by the CEA/Valrho, audits of the operators and impact assessments. All the procedures of operations related to the scrap metal are described in quality assurance documents. (author)

  10. The Influence of Home Scrap on Porosity of MgAl9Zn1 Alloy Pressure Castings

    Directory of Open Access Journals (Sweden)

    Konopka Z.

    2017-03-01

    Full Text Available The work presents the results of examinations concerning the influence of various amounts of home scrap additions on the porosity of castings made of MgAl9Zn1 alloy. The fraction of home scrap in the metal charge ranged from 0 to 100%. Castings were pressure cast by means of the hot-chamber pressure die casting machine under the industrial conditions in one of the domestic foundries. Additionally, for the purpose of comparison, the porosity of specimens cut out directly of the MgAl9Zn1 ingot alloy was also determined. The examinations consisted in the qualitative assessment of porosity by means of the optical microscopy and its quantitative determination by the method of weighting specimens in air and in water. It was found during the examination that the porosity of castings decreases with an increase in the home scrap fraction in the metal charge. The qualitative examinations confirmed the beneficial influence of the increased home scrap fraction on the porosity of castings. It was concluded that the reusing of home scrap in a foundry can be a good way of reduction of costs related to the production of pressure castings.

  11. Evaluation of coagulation factors and platelet function from an off-line modified ultrafiltration technique for post-cardiopulmonary bypass circuit blood recovery.

    Science.gov (United States)

    Beckmann, S; Lynn, P; Miller, S; Harris, R; DiMarco, R F; Ross, J E

    2013-05-01

    Modified ultrafiltration (MUF) is a technique that hemoconcentrates residual CPB circuit blood and the patient at the same time. Hemoconcentration and MUF are Class 1-A recommendations in the anesthesia and surgical blood conservation guidelines. This study evaluated the off-line MUF process of the Hemobag (HB, Global Blood Resources, Somers, CT, USA) to quantitate coagulation factor levels, platelet (PLT) count and function in one facility and cellular growth factor concentrations of the final product that were transfused to the patient in another facility In two cardiac surgery facilities, after decannulation, the extracorporeal circuit (ECC) blood from 22 patients undergoing cardiac surgery was processed with the HB device. In eleven patients from the first facility by the study design, blood samples for coagulation factor levels and PLT aggregation were drawn from the reservoir of the MUF device pre- and post-processing. The samples (n = 11) were sent to a reference laboratory where testing for prothrombin time (PT), international normalized ratio (INR), activated partial thromboplastin time (aPTT), reptilase time, fibrinogen, clotting factors II, V, VII, VIII, IX, X, ADAMTS-13, protein C, protein S, antithrombin III, von Willebrand Factor (vWF), and platelet (PLT) aggregation were performed. A portion of the final concentrated HB blood samples (n = 5-10) from the second facility by design were evaluated for transforming and platelet-derived cellular growth factor concentrations. On average, approximately 800 - 2000 mls of whole blood were removed from the ECC post-CPB for processing in the HB device. After processing, there was, on the average, approximately 300 - 950 mls of concentrated whole blood salvaged for reinfusion. The PT and INR were significantly lower in the post-processing product compared to the pre-processing samples while the aPTT times were not significantly different. All coagulation factors and natural anti-coagulants were significantly

  12. Emergency response during the radiological control of scraps in Cuba

    International Nuclear Information System (INIS)

    Ramos Viltre, Enma O.; Cardenas Herrera, Juan; Dominguez Ley, Orlando; Capote Ferrera, Eduardo; Fernandez Gomez, Isis M.; Caveda Ramos, Celia; Carrazana, Jorge; Barroso Perez, Idelisa

    2008-01-01

    In the last few years, in the international scene, incidents have been reported due to the presence of radioactive materials in the scrap. This reality has motivated the adoption of measures of radiological security, due to the implications that these incidents have for the public and the environment, as well as for the international trade. Among theses actions is the implementation of the radiological control of scrap, with the additional requirement that this control has to be implemented in the framework of a Quality Management Program.Taking into account the international experience, our institution designed and organized in 2002 a national service for the radiological monitoring of scrap, being the clients the main exporting and trading enterprises of this material in the country. During these years, several contaminated materials have been detected, causing incidents that activated the radiological emergency response system. In this sense, since some years ago, our country has been working in the implementation of a national and ministerial system for facing and mitigating the consequences of accidental radiological situations, conjugating efforts and wills from different national institutions with the leadership of the Center of Radiation Protection and Hygiene (CPHR) and the Center of Nuclear Security (CNSN) in correspondence with the social responsibility assigned to the them. These incidents propitiate to have not only a system of capacity and quick response oriented to limit the exposure of people, to control the sources, to mitigate the consequences of the accident and to reestablish the conditions of normality, but also a previous adequate planning that guarantees the speed and effectiveness of it. In these work the experiences reached by the specialists of the CPHR from Cuba during the occurrence of an incident in the execution of the service of radiological monitoring of scraps are exposed. (author)

  13. The Scrap Tire Problem: A Preliminary Economic Analysis (1985)

    Science.gov (United States)

    The purpose of the study was to conduct a preliminary economic analysis of the social benefits of EPA action to require more appropriate disposal of scrap tires versus the social costs of such an action.

  14. Hydroxyurea decreases hospitalizations in pediatric patients with Hb SC and Hb SB+ thalassemia

    Directory of Open Access Journals (Sweden)

    Lebensburger JD

    2015-12-01

    Full Text Available Jeffrey D Lebensburger, Rakeshkumar J Patel, Prasannalaxmi Palabindela, Christina J Bemrich-Stolz, Thomas H Howard, Lee M HilliardDivision of Pediatric Hematology Oncology, University of Alabama at Birmingham, Birmingham, AL, USAPurpose: Patients with hemoglobin SC (Hb SC and hemoglobin SB+ (Hb SB+ thalassemia suffer from frequent hospitalizations yet strong evidence of a clinical benefit of hydroxyurea (HU in this population is lacking. Patients with recurrent hospitalizations for pain crisis are offered HU at our institution based on small cohort data and anecdotal benefit. This study identifies outcomes from a large cohort of patients with Hb SC and SB+ thalassemia who were treated with HU for 2 years.Materials and methods: A retrospective review was conducted of 32 patients with Hb SC and SB+ thalassemia who were treated with HU. We reviewed the number, and reasons for hospitalization in the 2 years prior to, and 2 years post-HU treatment as well as laboratory changes from baseline, over 1 year.Results: Patients with Hb SC and SB+ thalassemia started on HU for frequent pain, had a significant reduction in hospitalizations over 2 years as compared to the 2 years prior to HU initiation (mean total hospitalizations/year: pre-HU: 1.6 vs post-HU 0.4 hospitalizations, P<0.001; mean pain hospitalizations/year: pre-HU 1.5 vs post-HU 0.3 hospitalizations, P<0.001. Patients demonstrated hematologic changes including an increase in percent fetal hemoglobin (%HbF pre–post HU (4.5% to 7.7%, P=0.002, mean corpuscular volume (74 to 86 fL, P<0,0001, and decrease in absolute neutrophil count (5.0 to 3.2×109/L, P=0.007. Patients with higher doses of HU demonstrated the greatest reduction in hospitalizations but this was unrelated to absolute neutrophil count.Conclusion: This cohort of patients with Hb SC and SB+ thalassemia provides additional support for using HU in patients with recurrent hospitalizations for pain. A large randomized multicenter trial of

  15. Design of the network for the radiological control in the recycling of metal scrap in Cuba

    International Nuclear Information System (INIS)

    Dominguez Ley, Orlando; Caveda Ramos, Celia; Ramos Viltre, Enma O.; Capote Ferrera, Eduardo; Alonso Abad, Dolores; Zerquera, Juan Tomas

    2008-01-01

    Full text: During the last six years, the Centre of Protection and Hygiene of the Radiations (CPHR) has given answer to the problem about the presence of radioactive materials in the scrap which is exported in Cuba. The service of radioactivity measurement in scraps has reduced the risks of the occurrence of this type of events in the main import and export enterprises in Cuba. This has been carried out using few resources, a properly qualified staff and a laboratory credited by the norm ISO 17025:00. There is not the same control in the enterprises that manipulate and process metallic scrap inside the country. With the objective of extending the radiological control of the metallic scrap to the whole country, a monitoring network was designed. The design was based on the experience accumulated during the years of service to the import and export enterprises. First, It was defined the most vulnerable points in the whole recycle chain for each province, prioritizing the scrap melting plants and the longest scrap yards. All possible scenarios were identified, a quality system was also designed and implemented and a course of Radiological Protection oriented to the metallurgist technicians who are linked with the performance of this practice was elaborated. The monitoring has two phases. First, the measurements are carried out in the measurement points in each province and the transmissions of the data related to the monitored scrap loads are sent to the CPHR. The second phase is the confection of the Declaration of Conformity at the CPHR. This declaration certifies that this scrap may be processed. For the operation of this network, two software were developed and are currently used. One of them allows the control of the information in monitoring point and sends the necessary data to CPHR for the confection of the Declaration of Conformity. The other controls all the information received from the monitoring points and generates the Declaration of Conformity

  16. Noneconomic factors influencing scrap metal disposition decisions at DOE and NRC-licensed nuclear facilities

    Energy Technology Data Exchange (ETDEWEB)

    Ewen, M.D.; Robinson, L.A.

    1997-02-01

    The U.S. Environmental Protection Agency (EPA) is currently developing radiation protection standards for scrap metal, which will establish criteria for the unconditional clearance of scrap from nuclear facilities. In support of this effort, Industrial Economics, Incorporated is assessing the costs and benefits attributable to the rulemaking. The first step in this analysis is to develop an in-depth understanding of the factors influencing scrap disposition decisions, so that one can predict current and future practices under existing requirements and compare them to the potential effects of EPA`s rulemaking. These baseline practices are difficult to predict due to a variety of factors. First, because decommissioning activities are just beginning at many sites, current practices do not necessarily provide an accurate indicator of how these practices may evolve as site managers gain experience with related decisions. Second, a number of different regulations and policies apply to these decisions, and the interactive effects of these requirements can be difficult to predict. Third, factors other than regulatory constraints and costs may have a significant effect on related decisions, such as concerns about public perceptions. In general, research suggests that these factors tend to discourage the unconditional clearance of scrap metal.

  17. TGFβ induces proHB-EGF shedding and EGFR transactivation through ADAM activation in gastric cancer cells

    International Nuclear Information System (INIS)

    Ebi, Masahide; Kataoka, Hiromi; Shimura, Takaya; Kubota, Eiji; Hirata, Yoshikazu; Mizushima, Takashi; Mizoshita, Tsutomu; Tanaka, Mamoru; Mabuchi, Motoshi; Tsukamoto, Hironobu; Tanida, Satoshi; Kamiya, Takeshi; Higashiyama, Shigeki; Joh, Takashi

    2010-01-01

    Research highlights: → TGFβ induces EGFR transactivation through proHB-EGF shedding by activated ADAM members in gastric cancer cells. → TGFβ induces nuclear translocation of HB-EGF-CTF cleaved by ADAM members. → TGFβ enhances cell growth by EGFR transactivation and HB-EGF-CTF nuclear translocation and ADAM inhibitors block these effects. → Silencing of ADAM17 also blocks EGFR transactivation, HB-EGF-CTF nuclear translocation and cancer cell growth by TGFβ. → ADAM17 may play a crucial role in this TGFβ-HB-EGF signal transduction. -- Abstract: Background and aims: Transforming growth factor-beta (TGFβ) is known to potently inhibit cell growth. Loss of responsiveness to TGFβ inhibition on cell growth is a hallmark of many types of cancer, yet its mechanism is not fully understood. Membrane-anchored heparin-binding EGF-like growth factor (proHB-EGF) ectodomain is cleaved by a disintegrin and metalloproteinase (ADAM) members and is implicated in epidermal growth factor receptor (EGFR) transactivation. Recently, nuclear translocation of the C-terminal fragment (CTF) of pro-HB-EGF was found to induce cell growth. We investigated the association between TGFβ and HB-EGF signal transduction via ADAM activation. Materials and methods: The CCK-8 assay in two gastric cancer cell lines was used to determine the effect for cell growth by TGFβ. The effect of two ADAM inhibitors was also evaluated. Induction of EGFR phosphorylation by TGFβ was analyzed and the effect of the ADAM inhibitors was also examined. Nuclear translocation of HB-EGF-CTF by shedding through ADAM activated by TGFβ was also analyzed. EGFR transactivation, HB-EGF-CTF nuclear translocation, and cell growth were examined under the condition of ADAM17 knockdown. Result: TGFβ-induced EGFR phosphorylation of which ADAM inhibitors were able to inhibit. TGFβ induced shedding of proHB-EGF allowing HB-EGF-CTF to translocate to the nucleus. ADAM inhibitors blocked this nuclear translocation. TGF

  18. Advanced technologies for decontamination and conversion of scrap metal

    International Nuclear Information System (INIS)

    MacNair, V.; Muth, T.; Shasteen, K.; Liby, A.; Hradil, G.; Mishra, B.

    1996-01-01

    In October 1993, Manufacturing Sciences Corporation was awarded DOE contract DE-AC21-93MC30170 to develop and test recycling of radioactive scrap metal (RSM) to high value and intermediate and final product forms. This work was conducted to help solve the problems associated with decontamination and reuse of the diffusion plant barrier nickel and other radioactively contaminated scrap metals present in the diffusion plants. Options available for disposition of the nickel include decontamination and subsequent release or recycled product manufacture for restricted end use. Both of these options are evaluated during the course of this research effort. work during phase I of this project successfully demonstrated the ability to make stainless steel from barrier nickel feed. This paved the way for restricted end use products made from stainless steel. Also, after repeated trials and studies, the inducto-slag nickel decontamination process was eliminated as a suitable alternative. Electro-refining appeared to be a promising technology for decontamination of the diffusion plant barrier material. Goals for phase II included conducting experiments to facilitate the development of an electro-refining process to separate technetium from nickel. In parallel with those activities, phase II efforts were to include the development of the necessary processes to make useful products from radioactive scrap metal. Nickel from the diffusion plants as well as stainless steel and carbon steel could be used as feed material for these products

  19. Morphological and mechanical analyses of laminates manufactured from randomly positioned carbon fibre/epoxy resin prepreg scraps

    Science.gov (United States)

    Souza, Christiane S. R.; Cândido, Geraldo M.; Alves, Wellington; Marlet, José Maria F.; Rezende, Mirabel C.

    2017-10-01

    This study aims to contribute to sustainability by proposing the reuse of composite prepreg scrap as an added value from discards. The research evaluates the microstructure and mechanical properties of laminates processed by the reuse of uncured carbon fibre/F155-epoxy resin prepreg scraps, waste from the ply cutting area of an aeronautical industry. The composite scraps were used as collected and were randomly positioned to produce laminates to be cured at an autoclave. The mechanical characterization shows a decrease of 39% for the compression property due to the discontinuous fibres in the laminate and an increase of 34% for the interlaminar shear strength, when compared to continuous fibre laminates. This increase is attributed to the higher crosslink density of the epoxy resin, as a result of the cure temperature used in autoclave (60 °C higher than suggested by supplier) and also to the randomly positioned scraps. Microscopic analyses confirm the consolidation of laminates, although show resin rich areas with different sizes and shapes attributed to the overlapping of the scraps with different sizes and shapes. These resin rich areas may contribute to decrease the mechanical properties of laminates. The correlation between mechanical and morphological results shows potential to be used on non-critical structural application, as composite jigs, contributing to sustainability.

  20. RECYCLING OF SCRAP AND WASTE OF COPPER AND COPPER ALLOYS IN BELARUS

    Directory of Open Access Journals (Sweden)

    S. L. Rovin

    2017-01-01

    Full Text Available The construction of a new casting and mechanical shop of unitary enterprise «Tsvetmet» in December 2015 has allowed to solve the complex problem of processing and utilization of scrap and wastes of copper and copper alloys in the Republic of Belarus. The technological processes of fire refinement of copper and manufacturing of copper rod from scrap and production of brass rod by hot pressing (extrusion of the continuously casted round billet have been mastered for the first time in the Republic of Belarus.

  1. Utilization of metal scrap for the production of waste drums for ultimate disposal

    International Nuclear Information System (INIS)

    Janberg, K.; Rittscher, D.

    1988-01-01

    The contribution reviews the history of development of the techniques for treatment of decommissioning scrap from the beginning of the 1980's onwards (decommissioning of the Niederaichbach and Gundremmingen nuclear power stations), together with the radiological measuring methods required for regulatory purposes. The advantages of the recycling of the metal scrap by means of melting, and of materials utilization for production of waste containers for ultimate storage are discussed together with product quality assurance criteria. (RB) [de

  2. Process for using lead battery scrap. Verfahren zum Verarbeiten von Bleiakkumulatorenschrott

    Energy Technology Data Exchange (ETDEWEB)

    Sycev, A P; Kim, G V; Larin, V F; Sidorova, G D; Vicharev, I G; Kuur, V P; Achmetov, R S; Moiseev, G L; Maslov, V I; Kabacek, V G

    1986-06-26

    The process for using lead battery scrap is such that it leads to an increase of lead metal without the use of fluxes for forming the melt. According to the invention, the battery scrap is broken up, dangerous parts (organic substances containing chlorine) are removed and large pieces of lead (pole bridges, grids, contact pins) are sorted out. The remainder is chopped up into pieces less than 10 mm in size. The small pieces are melted by the suspension melting process at a temperature of 1300 to 1500/sup 0/C in an oxidising atmosphere (air or oxygen) without using any fuel. As the small pieces contain parts of the battery case (= organic substances free of chlorine), they burn in air generating heat, which is then used to melt the sulphate oxide lead compounds. The previously sorted large lead parts are then added to the lead oxide melt. Finally, the lead oxide is reduced to lead metal with coke in a furnace. After the reduction of lead oxide to lead, less than 0.2% of the initial lead content in the battery scrap being processed is lost in the dumped slag.

  3. Effective regeneration of anode material recycled from scrapped Li-ion batteries

    Science.gov (United States)

    Zhang, Jin; Li, Xuelei; Song, Dawei; Miao, Yanli; Song, Jishun; Zhang, Lianqi

    2018-06-01

    Recycling high-valuable metal elements (such as Li, Ni, Co, Al and Cu elements) from scrapped lithium ion batteries can bring significant economic benefits. However, recycling and reusing anode material has not yet attracted wide attention up to now, due to the lower added-value than the above valuable metal materials and the difficulties in regenerating process. In this paper, a novel regeneration process with significant green advance is proposed to regenerate anode material recycled from scrapped Li-ion batteries for the first time. After regenerated, most acetylene black (AB) and all the styrene butadiene rubber (SBR), carboxymethylcellulose sodium (CMC) in recycled anode material are removed, and the surface of anode material is coated with pyrolytic carbon from phenolic resin again. Finally, the regenerated anode material (graphite with coating layer, residual AB and a little CMC pyrolysis product) is obtained. As expected, all the technical indexs of regenerated anode material exceed that of a midrange graphite with the same type, and partial technical indexs are even closed to that of the unused graphite. The results indicate the effective regeneration of anode material recycled from scrapped Li-ion batteries is really achieved.

  4. Evaluation of Wet Digestion Methods for Quantification of Metal Content in Electronic Scrap Material

    Directory of Open Access Journals (Sweden)

    Subhabrata Das

    2017-11-01

    Full Text Available Recent advances in the electronics sector and the short life-span of electronic products have triggered an exponential increase in the generation of electronic waste (E-waste. Effective recycling of E-waste has thus become a serious solid waste management challenge. E-waste management technologies include pyrometallurgy, hydrometallurgy, and bioleaching. Determining the metal content of an E-waste sample is critical in evaluating the efficiency of a metal recovery method in E-waste recycling. However, E-waste is complex and of diverse origins. The lack of a standard digestion method for E-waste has resulted in difficulty in comparing the efficiencies of different metal recovery processes. In this study, several solid digestion protocols including American Society for Testing and Materials (ASTM-D6357-11, United States Environment Protection Agency Solid Waste (US EPA SW 846 Method 3050b, ultrasound-assisted, and microwave digestion methods were compared to determine the metal content (Ag, Al, Au, Cu, Fe, Ni, Pb, Pd, Sn, and Zn of electronic scrap materials (ESM obtained from two different sources. The highest metal recovery (mg/g of ESM was obtained using ASTM D6357-11 for most of the metals, which remained mainly bound to silicate fractions, while a microwave-assisted digestion protocol (MWD-2 was more effective in solubilizing Al, Pb, and Sn. The study highlights the need for a judicious selection of digestion protocol, and proposes steps for selecting an effective acid digestion method for ESM.

  5. Statistical treatment of hazards result from radioactive material in metal scrap

    International Nuclear Information System (INIS)

    Salem, E.F.; Rashad, S.M.

    2013-01-01

    Radioactive sources have a wide range of uses in medicine and industry. Radioactive materials entering the public domain in an uncontrolled manner may creating a serious risk of radiation exposure for workers and the public as well as excessive costs for plant decontamination and waste of product to be borne by the metal industry. This paper describes the major accidents that had happened in the last decades due to radioactive material in metal scrap, provides assessment of associated hazards and lessons learned. This will help Regulatory Authority to introduce measures capable to avoid the recurrence of similar events. The study highlights the situation for metal scrap incidents in Egypt.

  6. First Report of a Chinese Family Carrying a Double Heterozygosity for Hb Q-Thailand and Hb J-Bangkok.

    Science.gov (United States)

    Jiang, Fan; Zhou, Jian-Ying; Yan, Jin-Mei; Lu, Yue-Cheng; Li, Dong-Zhi

    2016-11-01

    The double heterozygosity for α and β chain variants leads to the formation of abnormal heterodimer hybrids, which could render laboratory diagnostics in a routine setting difficult. The following is the first report of a double heterozygosity for Hb Q-Thailand [α74(EF3)Asp→His; HBA1: c.223G>C] with α + -thalassemia (α + -thal) and Hb J-Bangkok [β56(D7)Gly→Asp; HBB: c.170G>A] found in a Chinese family. Both subjects were healthy with normal or borderline hematological parameters. Hemoglobin (Hb) analyses showed a novel variant, Hb Q-Thailand and Hb J-Bangkok. Family studies helped in the initial recognition and in making presumptive diagnoses, but definitive diagnoses of these cases with complex α and β chain variants could only be obtained after DNA analysis.

  7. EFFECTOF ISOLATION WALL USING SCRAP TIRE ON GROUND VIBRATION REDUCTION

    Science.gov (United States)

    Kashimoto, Takahiko; Kashimoto, Yusuke; Hayakawa, Kiyoshi; Matsui, Tamotsu; Fujimoto, Hiroaki

    Some countermeasure methods against the environmental ground vibration caused by some traffic vibrations have been proposed so far. The authors have developed a new type ground vibration isolation wall using scrap tire, and evaluated its effectiveness on the ground vibration reduction by full scale field tests. In this paper, the authors discussed and examined the effectiveness of the developed countermeasure method by two field tests. The one concerns on the effect of scrap tire as soft material of vibration isolation wall, and the other on the effect of the developed countermeasure method practically applied in a residential area close to monorail traffic. As the results, it was elucidated that the ground vibration of 2-3 dB was reduced in case of two times volume of the soft material, the conversion ratio of the vibration energy of the soft material to the kinetic energy was higher than that of the core material of PHC pile, the vibration acceleration of 0.19 - 1.26 gal was reduced by the developed countermeasure method in case of the monorail traffic, and the vibration reduction measured behind the isolation wall agreed well with the proposed theoretical value, together with confirming the effectiveness of the ground vibration isolation wall using scrap tire as the countermeasure method against the environmental ground vibration.

  8. Radiation protection aspects of the trafficking radionuclides contaminated metal scrap

    International Nuclear Information System (INIS)

    Prouza, Z.

    1999-01-01

    This paper covers the legal base of the release in the environment of radionuclides containing materials and the radiation protection aspects of trafficking in radionuclides contaminated materials. Materials, substance and objects containing radionuclides or contaminated by them may be released into the environment, if they do not exceed values authorized by SONS (State Office of Nuclear Safety). Legislative measures should be taken against illicit trafficking of the nuclear material in all the areas. The creation of a sophisticated system for the control and regulation of all important radionuclides released into the environment should be based on the radiation protection limits, constraints, reference and exemption levels which are introduced in the legislative documents; the strong supervision of producers and users of the sealed sources by SONS side, in addition to the requirements of the licensing process of their sources; a complete data-base and information exchange system related to illicit trafficking in contaminated material; in this system all the authorities with jurisdiction should be involved. The responsibilities of the persons involved in metal scrap trafficking should include arrangement of appropriate monitoring, rules for transport of the metal scrap, an adequate measuring system to monitor metal scrap including monitoring to prevent processing or smelting of the radioactive material, control measures, etc. All of the above items of legislation are an important challenge for the Czech Republic. (author)

  9. Use of Portal Monitors for Detection of Technogenic Radioactive Sources in Scrap Metal

    Science.gov (United States)

    Solovev, D. B.; Merkusheva, A. E.

    2017-11-01

    The article considers the features of organization of scrap-metal primary radiation control on the specialized enterprises engaging in its deep processing and storage at using by primary technical equipment - radiation portal monitors. The issue of this direction relevance, validity of radiation control implementation with the use of radiation portal monitors, physical and organizational bases of radiation control are considered in detail. The emphasis is put on the considerable increase in the number of technogenic radioactive sources detected in scrap-metal that results in the entering into exploitation of radioactive metallic structures as different building wares. One of reasons of such increase of the number of technogenic radioactive sources getting for processing with scrap-metal is the absence of any recommendations on the radiation portal monitors exploitation. The practical division of the article offers to recommendation on tuning of the modes of work of radiation portal monitors depending on influence the weather factor thus allowing to considerably increase the percent of technogenic radioactive sources detection.

  10. PRODUCTION OF ELECTROTECHNICAL WIRE OF SCRAP AND COPPER WASTES

    Directory of Open Access Journals (Sweden)

    I. P. Volchok

    2006-01-01

    Full Text Available Chemical composition, structure and properties of copper upon base steps of wire production technology (melting of anode copper with using of scrap and waste, electrolitical refining, producing of rod by continuous casting, manufacture of electrotechnical wire and fibres is described.

  11. Influence of bone porcelain scraps on the physical characteristics and phase composition of a hard porcelain body

    Energy Technology Data Exchange (ETDEWEB)

    Nodeh, A.A.

    2017-07-01

    Hard porcelain is constituted in the alkali oxides-alumina-silica ternary system, and produced by a mixture of clay-feldspar and silica. The most important properties of this porcelain are high mechanical strength, translucency and whiteness. These properties depend on quality of raw material, firing temperature and soaking time. In bone porcelain bone ash was added to body composition up to 50wt.%. Generally hard porcelain and bone porcelain scrap cannot be reused in body composition. Whereas using these scrap could help natural resources. In this research using bon porcelain scraps in hard porcelain body have been investigated. Results show, this substitution decrease firing temperature, linear expansion and increase glass, probability of deformation and total shrinkage. Using 6wt.% bone porcelain scraps to hard porcelain body composition besides improving some properties, increases 1340°C firing mechanical strength two times and helps natural resources. (Author)

  12. Stress analysis of the HFIR HB-2 and HB-3 beam tube nozzles

    International Nuclear Information System (INIS)

    Williams, P.T.

    1998-08-01

    The results of three-dimensional linear elastic stress analyses of the HFIR HB-2 and HB-3 nozzles are presented in this report. Finite element models were developed using the PATRAN pre-processing code and translated into ABAQUS input file format. A scoping analysis using simple geometries with internal pressure loading was carried out to assess the capabilities of the ABAQUS/Standard code to calculate maximum principal stress distributions within cylinders with and without holes. These scoping calculations were also used to provide estimates for the variation in tangential stress around the rim of a nozzle using the superposition of published closed-form solutions for the stress around a hole in an infinite flat plate under uniaxial tension. From the results of the detailed finite element models, peak stress concentration factors (based on the maximum principal stresses in tension) were calculated to be 3.0 for the HB-2 nozzle and 2.8 for the HB-3 nozzle. Submodels for each nozzle were built to calculate the maximum principal stress distribution in the weldment region around the nozzle, where displacement boundary conditions for the submodels were automatically calculated by ABAQUS using the results of the global nozzle models. Maximum principal stresses are plotted and tabulated for eight positions around each nozzle and nozzle weldment

  13. Scrap tyre recycling process with molten zinc as direct heat transfer and solids separation fluid: A new reactor concept.

    Science.gov (United States)

    Riedewald, Frank; Goode, Kieran; Sexton, Aidan; Sousa-Gallagher, Maria J

    2016-01-01

    Every year about 1.5 billion tyres are discarded worldwide representing a large amount of solid waste, but also a largely untapped source of raw materials. The objective of the method was to prove the concept of a novel scrap tyre recycling process which uses molten zinc as the direct heat transfer fluid and, simultaneously, uses this media to separate the solids products (i.e. steel and rCB) in a sink-float separation at an operating temperature of 450-470 °C. This methodology involved: •construction of the laboratory scale batch reactor,•separation of floating rCB from the zinc,•recovery of the steel from the bottom of the reactor following pyrolysis.

  14. Coinheritance of High Oxygen Affinity Hb Helsinki [HBB: c.248A>T; β82(EF6)Lys→Met] with Hb H Disease.

    Science.gov (United States)

    Lee, Shir-Ying; Goh, Jia-Hui; Tan, Karen M L; Liu, Te-Chih

    2017-05-01

    Hb Helsinki [HBB: c.248A>T; β82(EF6)Lys→Met] is a high oxygen affinity hemoglobin (Hb) causing polycythemia, whereas Hb H (β4) disease causes mild to severe chronic hemolytic anemia. The clinical characteristics, gel electrophoresis, capillary electrophoresis (CE) and molecular genotyping of a case of Hb Helsinki coinherited with Hb H disease in an ethnic Malay is described, illustrating the interaction between the β-globin variant and coinheritance of three α gene deletions. The proband was asymptomatic, exhibited microcytosis and a normal with Hb value.

  15. Developing methods for detecting radioactive scrap

    International Nuclear Information System (INIS)

    Bellian, J.G.; Johnston, J.G.

    1995-01-01

    During the last 10 years, there have been major developments in radiation detection systems used for catching shielded radioactive sources in scrap metal. The original testing required to determine the extent of the problem and the preliminary designs of the first instruments will be discussed. Present systems available today will be described listing their advantages and disadvantages. In conclusion, the newest developments and state of the art equipment will also be included describing the limits and most appropriate locations for the systems

  16. Assignment of Responsibilities in the Management of Scrap Metal in Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Costa, E.L., E-mail: evaldo@cnen.gov.br [Comissao Nacional de Energia Nuclear (CNEN), Rio de Janeiro (Brazil)

    2011-07-15

    This paper gives an overview of the activities of the National Commission of Nuclear Energy (CNEN), as the Brazilian regulatory authority responsible for licensing, inspecting, controlling and regulating all practices involving sources of ionizing radiation. The activities of the main departments of CNEN responsible for taking care of the practices and sources are described, especially those related to orphan sources and radioactive material in scrap metal. Finally, although Brazil does not yet have the necessary infrastructure to take care of the scrap metal issue, through the joint action of the relevant departments of CNEN it is hoped that the appropriate steps can be taken to build a national protocol, following the examples of other countries, especially Spain. (author)

  17. Fernald scrap metal and recycling and beneficial reuse

    International Nuclear Information System (INIS)

    Motl, G.P.

    1993-01-01

    The Fernald plant, formerly known as the Feed Materials Production Facility, is located on a 1050-acre site 17 miles northwest of downtown Cincinnati, Ohio. Site construction was initiated in 1951 to fabricate uranium metal to meet defense production requirements of the U.S. Department of Energy (DOE). In October 1990, the DOE transferred management responsibility for the site from its Defense Programs organization to the Office of Environmental Restoration and Waste Management. In August 1991, the site was renamed the Fernald Environmental Management Project (FEMP) to reflect the site's new cleanup mission. During 40 yr of plant operation, a scrap metal storage area grew to contain 5000 t of scrap metal. Material in the pile, such as structural steel, crushed drums, tanks, and pipes, is contaminated with uranium to levels up to 200,000 disintegrations per minute alpha. In July 1991, cleanup of this pile was designated a CERCLA removal action under the Comprehensive Environmental Response, Compensation, and Liability Act and a consent agreement executed between the DOE and the U.S. Environmental Protection Agency

  18. Impact of demographics and disease progression on the relationship between glucose and HbA1c.

    Science.gov (United States)

    Claussen, Anetta; Møller, Jonas B; Kristensen, Niels R; Klim, Søren; Kjellsson, Maria C; Ingwersen, Steen H; Karlsson, Mats O

    2017-06-15

    Several studies have shown that the relationship between mean plasma glucose (MPG) and glycated haemoglobin (HbA1c) may vary across populations. Especially race has previously been referred to shift the regression line that links MPG to HbA1c at steady-state (Herman & Cohen, 2012). To assess the influence of demographic and disease progression-related covariates on the intercept of the estimated linear MPG-HbA1c relationship in a longitudinal model. Longitudinal patient-level data from 16 late-phase trials in type 2 diabetes with a total of 8927 subjects was used to study covariates for the relationship between MPG and HbA1c. The analysed covariates included age group, BMI, gender, race, diabetes duration, and pre-trial treatment. Differences between trials were taken into account by estimating a trial-to-trial variability component. Participants included 47% females and 20% above 65years. 77% were Caucasian, 9% were Asian, 5% were Black and the remaining 9% were analysed together as other races. Estimates of the change in the intercept of the MPG-HbA1c relationship due to the mentioned covariates were determined using a longitudinal model. The analysis showed that pre-trial treatment with insulin had the most pronounced impact associated with a 0.34% higher HbA1c at a given MPG. However, race, diabetes duration and age group also had an impact on the MPG-HbA1c relationship. Our analysis shows that the relationship between MPG and HbA1c is relatively insensitive to covariates, but shows small variations across populations, which may be relevant to take into account when predicting HbA1c response based on MPG measurements in clinical trials. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Characterization of a Novel Anti-Human HB-EGF Monoclonal Antibody Applicable for Paraffin-Embedded Tissues and Diagnosis of HB-EGF-Related Cancers.

    Science.gov (United States)

    Iwamoto, Ryo; Takagi, Mika; Akatsuka, Jun-Ichi; Ono, Ken-Ichiro; Kishi, Yoshiro; Mekada, Eisuke

    2016-04-01

    Heparin-binding EGF-like growth factor (HB-EGF) is a member of the EGF family of growth factors that bind to and activate the EGF receptor (EGFR/ErbB1) and ErbB4. HB-EGF plays pivotal roles in pathophysiological processes, including cancer. Thus, monoclonal antibodies (mAbs) for HB-EGF detection could be an important tool in the therapeutic diagnosis of HB-EGF-related cancers and other diseases. However, few mAbs, especially those applicable for immunohistochemistry (IHC), have been established to date. In this study, we generated a clone of hybridoma-derived mAb 2-108 by immunizing mice with recombinant human HB-EGF protein expressed by human cells. The mAb 2-108 specifically bound to human HB-EGF but not to mouse HB-EGF and was successful in immunoblotting, even under reducing conditions, immunoprecipitation, and immunofluorescence for unfixed as well as paraformaldehyde-fixed cells. Notably, this mAb was effective in IHC of paraffin-embedded tumor specimens. Epitope mapping analysis showed that mAb 2-108 recognized the N-terminal prodomain in HB-EGF. These results indicate that this new anti-HB-EGF mAb 2-108 would be useful in the diagnosis of HB-EGF-related cancers and would be a strong tool in both basic and clinical research on HB-EGF.

  20. Cellular response to 5-fluorouracil (5-FU in 5-FU-resistant colon cancer cell lines during treatment and recovery

    Directory of Open Access Journals (Sweden)

    Kravik Katherine L

    2006-05-01

    Full Text Available Abstract Background Treatment of cells with the anti-cancer drug 5-fluorouracil (5-FU causes DNA damage, which in turn affects cell proliferation and survival. Two stable wild-type TP53 5-FU-resistant cell lines, ContinB and ContinD, generated from the HCT116 colon cancer cell line, demonstrate moderate and strong resistance to 5-FU, respectively, markedly-reduced levels of 5-FU-induced apoptosis, and alterations in expression levels of a number of key cell cycle- and apoptosis-regulatory genes as a result of resistance development. The aim of the present study was to determine potential differential responses to 8 and 24-hour 5-FU treatment in these resistant cell lines. We assessed levels of 5-FU uptake into DNA, cell cycle effects and apoptosis induction throughout treatment and recovery periods for each cell line, and alterations in expression levels of DNA damage response-, cell cycle- and apoptosis-regulatory genes in response to short-term drug exposure. Results 5-FU treatment for 24 hours resulted in S phase arrests, p53 accumulation, up-regulation of p53-target genes on DNA damage response (ATF3, GADD34, GADD45A, PCNA, cell cycle-regulatory (CDKN1A, and apoptosis-regulatory pathways (FAS, and apoptosis induction in the parental and resistant cell lines. Levels of 5-FU incorporation into DNA were similar for the cell lines. The pattern of cell cycle progression during recovery demonstrated consistently that the 5-FU-resistant cell lines had the smallest S phase fractions and the largest G2(/M fractions. The strongly 5-FU-resistant ContinD cell line had the smallest S phase arrests, the lowest CDKN1A levels, and the lowest levels of 5-FU-induced apoptosis throughout the treatment and recovery periods, and the fastest recovery of exponential growth (10 days compared to the other two cell lines. The moderately 5-FU-resistant ContinB cell line had comparatively lower apoptotic levels than the parental cells during treatment and recovery

  1. Beyond HbA1c.

    Science.gov (United States)

    Bloomgarden, Zachary

    2017-12-01

    It can scarcely be denied that the supreme goal of all theory is to make the irreducible basic elements as simple and as few as possible without having to surrender the adequate representation of a single datum of experience. The diaTribe Foundation convened a meeting on the topic of glycemic outcomes beyond HbA1c on 21 July 2017, in Bethesda (MD, USA), focusing on potential uses of continuous glucose monitoring (CGM). Understanding patterns of glycemia in people with diabetes has long been a focus of approaches to improving treatment, and over the past few years this has become an available modality for clinical practice. Glucose levels are not the only biologic parameters affecting HbA1c levels; HbA1c changes with anemia or, more subtly, with changes in rates of erythrocyte turnover not reflected in hemoglobin levels outside the normal range. Renal disease often is associated with lower HbA1c than would be predicted based on an individual's glycemic levels. Furthermore, HbA1c levels tend to increase with age and are higher in some ethnic groups; for example, people of African ethnicity have higher HbA1c levels than people of Northern European descent. Indeed, we have argued that even as a measure of mean glycemia HbA1c is inherently imprecise. Overall, for some 20% of people with diabetes, HbA1c levels are substantially higher, or substantially lower, than those that would be predicted from mean blood glucose levels. If one recognizes that HbA1c is, at best, a partial measure of mean glycemic exposure, one must surely accept that HbA1c does not reflect variability within a day, from day to day, and from period to period. Many glucose-lowering medicines, particularly the sulfonylureas and insulin, cause hypoglycemia, with consequent negative effects on quality of life and patient-reported outcomes, as well as association with weight gain and adverse macrovascular outcome; hypoglycemia will, of course, not be captured by HbA1c measurement. Based on these

  2. The radiological monitoring protocol for metallic products and cleared scrap management

    International Nuclear Information System (INIS)

    Gil Lopez, E.

    2003-01-01

    Event though the use of nuclear and radiological techniques is subject to strict controls in most countries, the presence of radioactive material in batches of metallic scrap has been detected with relative frequency in the last few years. This circumstance has motivated the implementation of a series of national and international initiatives aimed at detecting and preventing this type of events, whether they be intentional or involuntary. The Spanish iron and steel industry is one of the country's most important industrial sectors, and to a great extent it depends on the importation of a very significant amount of metallic scrap that it uses as raw material. Experience has shown that countries that import large amounts of scrap, apart from supporting the mentioned international initiatives, should complement them with other national initiatives to reduce the risks resulting from the presence of radioactive material in scrap. In this context, the Spanish authorities, together with trade unions and entrepreneurial associations in the metal reclamations and smelting sectors and ENRESA, have signed a voluntary Protocol that defines and implements a national radiological monitoring and control system for scrap materials and their byproducts. The Protocol defines the obligations and rights of the signatories, and it describes the monitoring and control system and its legal bases, the operation of both specific and other general-purpose radiological monitoring equipment that existed prior to this initiative, the development of radiological training and dissemination plans for professionals in the metal reclamation and smelting sectors, the establishment of effective systems for the safe management of any radioactive materials detected, and the general improvement of the national response system in the event of radiological emergencies. Since the Protocol took effect in November 1999, more than 100 enterprises from the metallurgical (steel, copper, lead and aluminum

  3. Hb Tianshui (HBB: C.119A > G) in Compound Heterozygosity with Hb S (HBB: C.20A > T) from Odisha, India.

    Science.gov (United States)

    Meher, Satyabrata; Dehury, Snehadhini; Mohanty, Pradeep Kumar; Patel, Siris; Pattanayak, Chinmayee; Bhattacharya, Subhra; Das, Kishalaya; Sarkar, Biswanath

    2016-08-01

    We describe here a rare β-globin gene variant, Hb Tianshui [β39(C5)Glu→Arg; HBB: c.119A > G], detected during routine screening in Odisha, India. This is the second report of Hb Tianshui and the first to describe the cation exchange high performance liquid chromatography (HPLC) and DNA studies of two cases of this variant. Both cases had coinherited Hb S (HBB: c.20A > T) but none presented with typical symptoms of sickle cell disease. One of the cases was heterozygous for a common α-thalassemia (α-thal) allele (-α(3.7)) (rightward) (NG_000006.1: g.34164_37967del3804) and marginally raised Hb F percentage, while the other Hb S/Hb Tianshui case was completely benign and healthy. An atypical Asian Indian haplotype [+ - + - +] could be assigned to the Hb Tianshui variant. Hb Tianshui seems to mimic a few other Hb variants in cation exchange HPLC. However, we report two specific patterns in the chromatograms that are characteristic to Hb Tianshui. Combining an alkaline electrophoresis result with cation exchange HPLC at screening would be preferred to detect this rare variant, especially in regions with considerable frequency of Hb E [β26(B8)Glu→Lys; HBB: c.79G > A] or Hb S.

  4. Radiometric monitoring of contaminated scrap metals imported in Italy. Technical and regulatory features

    International Nuclear Information System (INIS)

    Dobici, F.; Piermattei, S.; Susanna, A.

    1996-01-01

    During these last ten years there have been occasional reports of mishaps from trafficking of contaminated scraps or containing radioactive sources. Recently an increase of events indicated that the problem becomes more important as to generate possible consequences, from a radiation protection standpoint, for workers and general public. Following the detection of contaminated metal scraps in some recycling industries and in some consignments entering the Italian borders, the competent Authorities laid down rules to put the matter under control. In this paper technical and regulatory features are discussed. (author)

  5. Simultaneous dual syringe electrospinning system using benign solvent to fabricate nanofibrous P(3HB-co-4HB)/collagen peptides construct as potential leave-on wound dressing

    International Nuclear Information System (INIS)

    Vigneswari, S.; Murugaiyah, V.; Kaur, G.; Abdul Khalil, H.P.S.; Amirul, A.A.

    2016-01-01

    The main focus of this study is the incorporation of collagen peptides to fabricate P(3-hydroxybutyrate-co-4-hydroxybutyrate) [P(3HB-co-4HB)] nano-fiber construct to further enhance surface wettability and support cell growth while harbouring desired properties for biodegradable wound dressing. Simultaneous electrospinning of nanofiber P(3HB-co-4HB)/collagen peptides construct was carried out using dual syringe system. The wettability of the constructs increased with the increase in 4HB molar fraction from 20 mol% 4HB [53.2°], P(3HB-co-35 mol%4HB)[48.9°], P(3HB-co-50 mol%4HB)[44.5°] and P(3HB-co-82 mol%4HB) [37.7°]. In vitro study carried out using mouse fibroblast cells (L929) grown on nanofiber P(3HB-co-4HB)/collagen peptides construct showed an increase in cell proliferation. In vivo study using animal model (Sprague Dawley rats) showed that nanofibrous P(3HB-co-4HB)/collagen peptides construct had a significant effect on wound contractions with the highest percentage of wound closure of 79%. Hence, P(3HB-co-4HB)/collagen peptides construct suitable for wound dressing have been developed using nano-fabrication technique. - Highlights: • Nano-fiber construct to enhance surface wettability and cell growth, harbouring desired properties as biodegradable wound dressing. • Simultaneous electrospinning of nanofiber P(3HB-co-4HB)/collagen construct using dual syringe system. • Nanofibrous construct accelerated wound healing with efficient cellular organization.

  6. Simultaneous dual syringe electrospinning system using benign solvent to fabricate nanofibrous P(3HB-co-4HB)/collagen peptides construct as potential leave-on wound dressing

    Energy Technology Data Exchange (ETDEWEB)

    Vigneswari, S. [Malaysian Institute of Pharmaceuticals and Nutraceuticals, NIBM, MOSTI, 11700 Penang (Malaysia); Institute of Marine Biotechnology, Universiti Malaysia Terengganu, 21030 Kuala Terengganu (Malaysia); Murugaiyah, V. [School of Pharmaceutical Sciences, Universiti Sains Malaysia, 11700 Penang (Malaysia); Kaur, G. [Institute of Research in Molecular Medicine, Universiti Sains Malaysia, 11700 Penang (Malaysia); Abdul Khalil, H.P.S. [School of Industrial Technology, Universiti Sains Malaysia, 11700 Penang (Malaysia); Amirul, A.A., E-mail: amirul@usm.my [Malaysian Institute of Pharmaceuticals and Nutraceuticals, NIBM, MOSTI, 11700 Penang (Malaysia); School of Biological Sciences, Universiti Sains Malaysia, 11800 Penang (Malaysia); Centre of Chemical Biology, Universiti Sains Malaysia, 11900 Penang (Malaysia)

    2016-09-01

    The main focus of this study is the incorporation of collagen peptides to fabricate P(3-hydroxybutyrate-co-4-hydroxybutyrate) [P(3HB-co-4HB)] nano-fiber construct to further enhance surface wettability and support cell growth while harbouring desired properties for biodegradable wound dressing. Simultaneous electrospinning of nanofiber P(3HB-co-4HB)/collagen peptides construct was carried out using dual syringe system. The wettability of the constructs increased with the increase in 4HB molar fraction from 20 mol% 4HB [53.2°], P(3HB-co-35 mol%4HB)[48.9°], P(3HB-co-50 mol%4HB)[44.5°] and P(3HB-co-82 mol%4HB) [37.7°]. In vitro study carried out using mouse fibroblast cells (L929) grown on nanofiber P(3HB-co-4HB)/collagen peptides construct showed an increase in cell proliferation. In vivo study using animal model (Sprague Dawley rats) showed that nanofibrous P(3HB-co-4HB)/collagen peptides construct had a significant effect on wound contractions with the highest percentage of wound closure of 79%. Hence, P(3HB-co-4HB)/collagen peptides construct suitable for wound dressing have been developed using nano-fabrication technique. - Highlights: • Nano-fiber construct to enhance surface wettability and cell growth, harbouring desired properties as biodegradable wound dressing. • Simultaneous electrospinning of nanofiber P(3HB-co-4HB)/collagen construct using dual syringe system. • Nanofibrous construct accelerated wound healing with efficient cellular organization.

  7. Measurements of red cell deformability and hydration reflect HbF and HbA2 in blood from patients with sickle cell anemia.

    Science.gov (United States)

    Parrow, Nermi L; Tu, Hongbin; Nichols, James; Violet, Pierre-Christian; Pittman, Corinne A; Fitzhugh, Courtney; Fleming, Robert E; Mohandas, Narla; Tisdale, John F; Levine, Mark

    2017-06-01

    Decreased erythrocyte deformability, as measured by ektacytometry, may be associated with disease severity in sickle cell anemia (SCA). Heterogeneous populations of rigid and deformable cells in SCA blood result in distortions of diffraction pattern measurements that correlate with the concentration of hemoglobin S (HbS) and the percentage of irreversibly sickled cells. We hypothesize that red cell heterogeneity, as well as deformability, will also be influenced by the concentration of alternative hemoglobins such as fetal hemoglobin (HbF) and the adult variant, HbA 2 . To test this hypothesis, we investigate the relationship between diffraction pattern distortion, osmotic gradient ektacytometry parameters, and the hemoglobin composition of SCA blood. We observe a correlation between the extent of diffraction pattern distortions and percentage of HbF and HbA 2 . Osmotic gradient ektacytometry data indicate that minimum elongation in the hypotonic region is positively correlated with HbF, as is the osmolality at which it occurs. The osmolality at both minimum and maximum elongation is inversely correlated with HbS and HbA 2 . These data suggest that HbF may effectively improve surface-to-volume ratio and osmotic fragility in SCA erythrocytes. HbA 2 may be relatively ineffective in improving these characteristics or cellular hydration at the levels found in this patient cohort. Copyright © 2017. Published by Elsevier Inc.

  8. Development of an integrated MOX-scrap recycling flow-sheet by dry and wet routes using microwave heating techniques

    Energy Technology Data Exchange (ETDEWEB)

    Mallik, G K; Malav, R K; Karande, A P; Bhargava, V K; Kamath, H S [Advanced Fuel Fabrication Facility, Bhabha Atomic Research Centre, Tarapur (India)

    1999-01-01

    A simple, short and efficient scrap, recycling flow-sheet, which is exclusively based on microwave heating techniques and, includes both dry and wet routes, for (U,Pu)O{sub 2} fuel scrap recycling has been developed and evaluated. (author) 6 refs., 1 tab.

  9. Drugs affecting HbA1c levels

    Directory of Open Access Journals (Sweden)

    Ranjit Unnikrishnan

    2012-01-01

    Full Text Available Glycated hemoglobin (HbA1c is an important indicator of glycemic control in diabetes mellitus, based on which important diagnostic and therapeutic decisions are routinely made. However, there are several situations in which the level of HbA1c may not faithfully reflect the glycemic control in a given patient. Important among these is the use of certain non-diabetic medications, which can affect the HbA1c levels in different ways. This review focuses on the non-diabetic medications which can inappropriately raise or lower the HbA1c levels, and the postulated mechanisms for the same.

  10. Recovering heavy rare earth metals from magnet scrap

    Science.gov (United States)

    Ott, Ryan T.; McCallum, Ralph W.; Jones, Lawrence L.

    2017-08-08

    A method of treating rare earth metal-bearing permanent magnet scrap, waste or other material in a manner to recover the heavy rare earth metal content separately from the light rare earth metal content. The heavy rare earth metal content can be recovered either as a heavy rare earth metal-enriched iron based alloy or as a heavy rare earth metal based alloy.

  11. TGF{beta} induces proHB-EGF shedding and EGFR transactivation through ADAM activation in gastric cancer cells

    Energy Technology Data Exchange (ETDEWEB)

    Ebi, Masahide [Department of Gastroenterology and Metabolism, Nagoya City University Graduate School of Medical Sciences, Nagoya (Japan); Kataoka, Hiromi, E-mail: hkataoka@med.nagoya-cu.ac.jp [Department of Gastroenterology and Metabolism, Nagoya City University Graduate School of Medical Sciences, Nagoya (Japan); Shimura, Takaya; Kubota, Eiji; Hirata, Yoshikazu; Mizushima, Takashi; Mizoshita, Tsutomu; Tanaka, Mamoru; Mabuchi, Motoshi; Tsukamoto, Hironobu; Tanida, Satoshi; Kamiya, Takeshi [Department of Gastroenterology and Metabolism, Nagoya City University Graduate School of Medical Sciences, Nagoya (Japan); Higashiyama, Shigeki [Department of Biochemistry and Molecular Genetics, Ehime University Graduate School of Medicine, Ehime (Japan); Joh, Takashi [Department of Gastroenterology and Metabolism, Nagoya City University Graduate School of Medical Sciences, Nagoya (Japan)

    2010-11-19

    Research highlights: {yields} TGF{beta} induces EGFR transactivation through proHB-EGF shedding by activated ADAM members in gastric cancer cells. {yields} TGF{beta} induces nuclear translocation of HB-EGF-CTF cleaved by ADAM members. {yields} TGF{beta} enhances cell growth by EGFR transactivation and HB-EGF-CTF nuclear translocation and ADAM inhibitors block these effects. {yields} Silencing of ADAM17 also blocks EGFR transactivation, HB-EGF-CTF nuclear translocation and cancer cell growth by TGF{beta}. {yields} ADAM17 may play a crucial role in this TGF{beta}-HB-EGF signal transduction. -- Abstract: Background and aims: Transforming growth factor-beta (TGF{beta}) is known to potently inhibit cell growth. Loss of responsiveness to TGF{beta} inhibition on cell growth is a hallmark of many types of cancer, yet its mechanism is not fully understood. Membrane-anchored heparin-binding EGF-like growth factor (proHB-EGF) ectodomain is cleaved by a disintegrin and metalloproteinase (ADAM) members and is implicated in epidermal growth factor receptor (EGFR) transactivation. Recently, nuclear translocation of the C-terminal fragment (CTF) of pro-HB-EGF was found to induce cell growth. We investigated the association between TGF{beta} and HB-EGF signal transduction via ADAM activation. Materials and methods: The CCK-8 assay in two gastric cancer cell lines was used to determine the effect for cell growth by TGF{beta}. The effect of two ADAM inhibitors was also evaluated. Induction of EGFR phosphorylation by TGF{beta} was analyzed and the effect of the ADAM inhibitors was also examined. Nuclear translocation of HB-EGF-CTF by shedding through ADAM activated by TGF{beta} was also analyzed. EGFR transactivation, HB-EGF-CTF nuclear translocation, and cell growth were examined under the condition of ADAM17 knockdown. Result: TGF{beta}-induced EGFR phosphorylation of which ADAM inhibitors were able to inhibit. TGF{beta} induced shedding of proHB-EGF allowing HB-EGF-CTF to

  12. Measures to detect and control radioactive contaminated metallurgical scrap at border checkpoints in Poland

    International Nuclear Information System (INIS)

    Smagala, G.

    1999-01-01

    The issue of radioactive contaminated metallurgical scrap has never received a high priority in Poland and in the international community. Since the dissolution of the former Soviet Union a higher attention has been given to the problem. Poland which is located between the West and East Europe has the obligation to develop and implement an effective prevention and detection system. The reasons to increase national control and detection system at the border checkpoints in Poland are to avoid the following risks: post Chernobyl contamination transports of commodities; transport of contaminated metal scrap; transfer of radioactive waste for their disposal or utilization; high risk of becoming a transit country of illicit trafficking of nuclear materials and radioactive sources. In order to avoid the above-mentioned risks, Poland initiated in 1990, a deployment of the portable radiation devices at the border checkpoints and, as of 1998, the number of installed instruments exceeded a hundred. This paper presents Poland's activities to detect contaminated scrap at its border checkpoints. (author)

  13. [About the HbA1c in the elderly].

    Science.gov (United States)

    Farcet, Anaïs; Delalande, Géraldine; Oliver, Charles; Retornaz, Frédérique

    2016-03-01

    HbA1c product of non enzymatic glycation of HbA increases in relation with the mean blood glucose level during the former 2-3 months. HbA1c levels are correlated with the development of diabetic complications and HbA1c assessment is now the gold standard for evaluation of diabetes control. HbA1c level should not be higher than 7% to avoid these complications. However, in aged peoples, the objectives of diabetes control vary according to their health status. It must be good with HbA1c lower than 7-7.5% in healthy subjects and more relax in subjects with symptoms of frailty and risks of non perceived and self corrected hypoglycemia. Under these conditions, HbA1c values lower than 8 to 9% are advised. Nevertheless, hypoglycemia episodes may occur in patients with high HbA1c and capillary glucose follow-up is necessary for detection of such complications.

  14. Innovative technologies for recycling contaminated concrete and scrap metal

    International Nuclear Information System (INIS)

    Bossart, S.J.; Moore, J.

    1993-01-01

    Decontamination and decommissioning of US DOE's surplus facilities will generate enormous quantities of concrete and scrap metal. A solicitation was issued, seeking innovative technologies for recycling and reusing these materials. Eight proposals were selected for award. If successfully developed, these technologies will enable DOE to clean its facilities by 2019

  15. Detection of Hb Constant Spring (HBA2: c.427T>C) Heterozygotes in Combination with β-Thalassemia or Hb E Trait by Capillary Electrophoresis.

    Science.gov (United States)

    Pornprasert, Sakorn; Saoboontan, Supansa; Punyamung, Manoo

    2015-01-01

    Hb Constant Spring (Hb CS; HBA2: c.427T>C) is often missed by routine laboratory testing as its mRNA as well as gene product are unstable and presented at a low level in peripheral blood. This study aimed to analyze the efficacy of capillary electrophoresis (CE) for detecting and quantifying of Hb CS in β-thalassemia (β-thal) trait or Hb E (HBB: c.79G>A) trait samples with reduced β-globin chain expression. Thalassemia diagnostic data were reviewed in 2524 blood samples that were submitted to the laboratory of the Associated Medical Sciences Clinical Service Center, Chiang Mai, Thailand for hemoglobinopathy and thalassemia diagnosis. DNA analysis for Hb CS was performed in 322 β-thal trait and 397 Hb E trait samples using the amplification refractory mutation system (ARMS). The CE electropherogram of Hb CS at zone 2 was observed in all five samples with β-thal trait and nine samples with Hb E trait with levels varying from 0.1-2.8 and 0.1-2.3%, respectively. Thus, the CE method proved useful for screening of Hb CS in samples with β-thal trait or Hb E trait, which is essential for providing accurate diagnosis, genetic counseling, prevention and control programs of Hb H-CS disease.

  16. Recycle of contaminated scrap metal, Volume 2. Semi-annual report, September 1993--January 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-07-01

    Catalytic Extraction Processing (CEP) has been demonstrated to be a robust, one-step process that is relatively insensitive to wide variations in waste composition and is applicable to a broad spectrum of DOE wastes. Catalytic Processing Unit (CPU) design models have been validated through experimentation to provide a high degree of confidence in our ability to design a bulk solids CPU for processing DOE wastes. Two commercial CEP facilities have been placed in commission and are currently processing mixed low level wastes. These facilities provide a compelling indication of the maturity, regulatory acceptance, and commercial viability of CEP. In concert with the DOE, Nolten Metal Technology designed a program which would challenge preconceptions of the limitations of waste processing technologies: demonstrate the recycling of ferrous and non-ferrous metals--to establish that radioactively contaminated scrap metal could be converted to high-grade, ferrous and non-ferrous alloys which can be reused by DOE or reintroduced into commerce; immobilize radionuclides--that CEP would concentrate the radionuclides in a durable vitreous phase, minimize secondary waste generation and stabilize and reduce waste volume; destroy hazardous organics--that CEP would convert hazardous organics to valuable industrial gases, which could be used as an energy source; recover volatile heavy metals--that CEP`s off-gas treatment system would capture volatile heavy metals, such as mercury and lead; and establish that CEP is economical for processing contaminated scrap metal in the DOE inventory. The execution of this program resulted in all objectives being met. Volume II contains: Task 1.4, optimization of the vitreous phase for stabilization of radioactive species; Task 1.5, experimental testing of Resource Conservation and Recovery Act (RCRA) wastes; and Task 1.6, conceptual design of a CEP facility.

  17. Recycle of contaminated scrap metal, Volume 2. Semi-annual report, September 1993--January 1996

    International Nuclear Information System (INIS)

    1996-07-01

    Catalytic Extraction Processing (CEP) has been demonstrated to be a robust, one-step process that is relatively insensitive to wide variations in waste composition and is applicable to a broad spectrum of DOE wastes. Catalytic Processing Unit (CPU) design models have been validated through experimentation to provide a high degree of confidence in our ability to design a bulk solids CPU for processing DOE wastes. Two commercial CEP facilities have been placed in commission and are currently processing mixed low level wastes. These facilities provide a compelling indication of the maturity, regulatory acceptance, and commercial viability of CEP. In concert with the DOE, Nolten Metal Technology designed a program which would challenge preconceptions of the limitations of waste processing technologies: demonstrate the recycling of ferrous and non-ferrous metals--to establish that radioactively contaminated scrap metal could be converted to high-grade, ferrous and non-ferrous alloys which can be reused by DOE or reintroduced into commerce; immobilize radionuclides--that CEP would concentrate the radionuclides in a durable vitreous phase, minimize secondary waste generation and stabilize and reduce waste volume; destroy hazardous organics--that CEP would convert hazardous organics to valuable industrial gases, which could be used as an energy source; recover volatile heavy metals--that CEP's off-gas treatment system would capture volatile heavy metals, such as mercury and lead; and establish that CEP is economical for processing contaminated scrap metal in the DOE inventory. The execution of this program resulted in all objectives being met. Volume II contains: Task 1.4, optimization of the vitreous phase for stabilization of radioactive species; Task 1.5, experimental testing of Resource Conservation and Recovery Act (RCRA) wastes; and Task 1.6, conceptual design of a CEP facility

  18. Modeling the energy content of combustible ship-scrapping waste at Alang-Sosiya, India, using multiple regression analysis.

    Science.gov (United States)

    Reddy, M Srinivasa; Basha, Shaik; Joshi, H V; Sravan Kumar, V G; Jha, B; Ghosh, P K

    2005-01-01

    Alang-Sosiya is the largest ship-scrapping yard in the world, established in 1982. Every year an average of 171 ships having a mean weight of 2.10 x 10(6)(+/-7.82 x 10(5)) of light dead weight tonnage (LDT) being scrapped. Apart from scrapped metals, this yard generates a massive amount of combustible solid waste in the form of waste wood, plastic, insulation material, paper, glass wool, thermocol pieces (polyurethane foam material), sponge, oiled rope, cotton waste, rubber, etc. In this study multiple regression analysis was used to develop predictive models for energy content of combustible ship-scrapping solid wastes. The scope of work comprised qualitative and quantitative estimation of solid waste samples and performing a sequential selection procedure for isolating variables. Three regression models were developed to correlate the energy content (net calorific values (LHV)) with variables derived from material composition, proximate and ultimate analyses. The performance of these models for this particular waste complies well with the equations developed by other researchers (Dulong, Steuer, Scheurer-Kestner and Bento's) for estimating energy content of municipal solid waste.

  19. Inhibition of Hb Binding to GP1bα Abrogates Hb-Mediated Thrombus Formation on Immobilized VWF and Collagen under Physiological Shear Stress.

    Science.gov (United States)

    Annarapu, Gowtham K; Singhal, Rashi; Peng, Yuandong; Guchhait, Prasenjit

    2016-01-01

    Reports including our own describe that intravascular hemolysis increases the risk of thrombosis in hemolytic disorders. Our recent study shows that plasma Hb concentrations correlate directly with platelet activation in patients with paroxysmal nocturnal hemoglobinuria (PNH). The binding of Hb to glycoprotein1bα (GP1bα) increases platelet activation. A peptide AA1-50, designed from N-terminal amino acid sequence of GP1bα significantly inhibits the Hb binding to GP1bα as well as Hb-induced platelet activation. This study further examined if the Hb-mediated platelet activation plays any significant role in thrombus formation on subendothelium matrix under physiological flow shear stresses and the inhibition of Hb-platelet interaction can abrogate the above effects of Hb. Study performed thrombus formation assay in vitro by perfusing whole blood over immobilized VWF or collagen type I in presence of Hb under shear stresses simulating arterial or venous flow. The Hb concentrations ranging from 5 to 10 μM, commonly observed level in plasma of the hemolytic patients including PNH, dose-dependently increased thrombus formation on immobilized VWF under higher shear stress of 25 dyne/cm2, but not at 5 dyne/cm2. The above Hb concentrations also increased thrombus formation on immobilized collagen under both shear stresses of 5 and 25 dyne/cm2. The peptide AA1-50 abrogated invariably the above effects of Hb on thrombus formation. This study therefore indicates that the Hb-induced platelet activation plays a crucial role in thrombus formation on immobilized VWF or collagen under physiological flow shear stresses. Thus suggesting a probable role of this mechanism in facilitating thrombosis under hemolytic conditions.

  20. Association between recovery from Bell's palsy and body mass index.

    Science.gov (United States)

    Choi, S A; Shim, H S; Jung, J Y; Kim, H J; Kim, S H; Byun, J Y; Park, M S; Yeo, S G

    2017-06-01

    Although many factors have been found to be involved in recovery from Bell's palsy, no study has investigated the association between recovery from Bell's palsy and obesity. This study therefore evaluated the association between recovery from Bell's palsy and body mass index (BMI). Subjects were classified into five groups based on BMI (kg/m 2 ). Demographic and clinical characteristics were compared among these groups. Assessed factors included sex, age, time from paralysis to visiting a hospital, the presence of comorbidities such as diabetes mellitus and hypertension, degree of initial facial nerve paralysis by House-Brackmann (H-B) grade and neurophysiological testing, and final recovery rate. Based on BMI, 37 subjects were classified as underweight, 169 as normal weight, 140 as overweight, 155 as obese and 42 as severely obese. Classification of the degree of initial facial nerve paralysis as moderate or severe, according to H-B grade and electroneurography, showed no difference in severity of initial facial paralysis among the five groups (P > 0.05). However, the final recovery rate was significantly higher in the normal weight than in the underweight or obese group (P < 0.05). Obesity or underweight had no effect on the severity of initial facial paralysis, but the final recovery rate was lower in the obese and underweight groups than in the normal group. © 2016 John Wiley & Sons Ltd.

  1. Problems with radioactivity scrap in the iron and steel industry of the Czech and Slovak Republics

    International Nuclear Information System (INIS)

    Raab, J.; Toman, V.

    1999-01-01

    During the recent restructuring process, the Czech steel industry has undergone a drastic reduction in the steel production by around 40%. Under such situation, previously exported volumes have been diverted into domestic markets. For the export, the Czech steel industry had to make its efforts in enhancing the quality of products and in improving the technologies in accordance with ISO standards (ISO 9000 and also ISO 14000). Among the various new quality demands in the export market, the radioactive contamination of steel products has received a very high attention. The Czech Iron and Steel Federation has organized a working team specialized in solving the problems arising from radioactive contaminated metallurgical scrap and steel products. The working team is made up of specialists from steel producers and scrap handling firms of the Czech Republic and the Slovak Republic, of experts from the State Office for Nuclear Safety, the Ministry of Industry and Trade and the Metrological Institute. Members of the Inspectorate for Ionizing Radiation and the General Directory for Customs are also included. This working team takes part in the elaboration of the legislative norms in that area. This paper deals with all the detailed functions of the working team. At present, all the major Czech steel producers have installed stationary radiation monitoring systems for detecting the possible radioactivity in all materials entering into factories. Under an agreement arranged between the producers of the Czech Iron and Steel Federation, the tolerable range of radionuclide contents in steel scrap and steel products has been set at the maximum of 100 Bq/kg in ( scrap and steel products. In this respect, the large firms collecting and treating scrap have also installed stationary radiation monitoring systems. In such monitoring systems, the detector will measure and check the values of radioactivity above 10 - 15% higher than the natural background level. In the case that

  2. Soil and groundwater contamination with heavy metals at two scrap iron and metal recycling facilities

    DEFF Research Database (Denmark)

    Jensen, Dorthe Lærke; Holm, P. E.; Christensen, Thomas Højlund

    2000-01-01

    Field studies were performed at two actual scrap iron and metal recycling facilities in order to evaluate the extent of heavy metal migration into subsoil and groundwater caused by more than 25 years of handling scrap directly on the ground without any measures to prevent leaching. Surface soil...... samples, called `scrap dirt', representing the different activities on the two recycling facilities, all showed very high concentrations of lead (Pb), copper (Cu) and zinc (Zn), high concentrations of cadmium (Cd) , chromium (Cr) and nickel (Ni) and somewhat elevated concentrations of many other metals....... In particular high concentrations were found for Pb at the car-battery salvage locations (13 to 26 g Pb kg±1) and Cu at the cable burning location (22 g Cu kg±1) at one site. The migration of metals below the surface in general (except at the car-battery salvage locations) was very limited even after...

  3. REMOVING ZINC FROM GALVANIZED STEEL SCRAP TO FEASIBLE THE BOF SLUDGE RECYCLING

    Directory of Open Access Journals (Sweden)

    Mônica Marques Caetano de Lima

    2013-06-01

    Full Text Available Galvanized steel scraps generated at Usiminas Ipatinga are recycled in BOF converters. Although they are noble products, they contain a significant quantity of zinc that escapes from the bath due to its high vapor pressure and is captured by the gas control system, appearing in BOF sludge. As BOF sludge contains high iron content, it could be recycled to the process, but due to its zinc content, it is disposed in landfills. For this reason, this study aimed to treat these scraps to remove zinc layer using a thermal treatment process. The samples were fed to a rotative furnace in an inert ambient. It was tested the hot dip galvanized and eletrogalvanized scraps, varying the zinc coating weight between 20g/m2 and 150g/m2, temperature between 700°C and 900°C and time between 3 minutes and 10 minutes. Considering these conditions, it is verified that more than 70% of the zinc layer is removed at 700°C, in 10 minutes. Dust captured is about 60% of metallic zinc and 40% as zinc oxide. Based on these results, the recycling of BOF sludge can be feasible to the ironmaking process.

  4. Bioleaching of metals from electronic scrap by moderately thermophilic acidophilic bacteria

    NARCIS (Netherlands)

    Ilyas, Sadia; Anwar, Munir A.; Niazi, Shahida B.; Ghauri, M. Afzal

    The present work was aimed at studying the bioleachability of metals from electronic scrap by the selected moderately thermophilic strains of acidophilic chemolithotrophic and acidophilic heterotrophic bacteria. These included Sulfobacillus thermosulfidooxidans and an unidentified acidophilic

  5. Production of Magnesium and Aluminum-Magnesium Alloys from Recycled Secondary Aluminum Scrap Melts

    Science.gov (United States)

    Gesing, Adam J.; Das, Subodh K.; Loutfy, Raouf O.

    2016-02-01

    An experimental proof of concept was demonstrated for a patent-pending and trademark-pending RE12™ process for extracting a desired amount of Mg from recycled scrap secondary Al melts. Mg was extracted by electrorefining, producing a Mg product suitable as a Mg alloying hardener additive to primary-grade Al alloys. This efficient electrorefining process operates at high current efficiency, high Mg recovery and low energy consumption. The Mg electrorefining product can meet all the impurity specifications with subsequent melt treatment for removing alkali contaminants. All technical results obtained in the RE12™ project indicate that the electrorefining process for extraction of Mg from Al melt is technically feasible. A techno-economic analysis indicates high potential profitability for applications in Al foundry alloys as well as beverage—can and automotive—sheet alloys. The combination of technical feasibility and potential market profitability completes a successful proof of concept. This economical, environmentally-friendly and chlorine-free RE12™ process could be disruptive and transformational for the Mg production industry by enabling the recycling of 30,000 tonnes of primary-quality Mg annually.

  6. Human neural stem cells over-expressing VEGF provide neuroprotection, angiogenesis and functional recovery in mouse stroke model.

    Directory of Open Access Journals (Sweden)

    Hong J Lee

    Full Text Available BACKGROUND: Intracerebral hemorrhage (ICH is a lethal stroke type. As mortality approaches 50%, and current medical therapy against ICH shows only limited effectiveness, an alternative approach is required, such as stem cell-based cell therapy. Previously we have shown that intravenously transplanted human neural stem cells (NSCs selectively migrate to the brain and induce behavioral recovery in rat ICH model, and that combined administration of NSCs and vascular endothelial growth factor (VEGF results in improved structural and functional outcome from cerebral ischemia. METHODS AND FINDINGS: We postulated that human NSCs overexpressing VEGF transplanted into cerebral cortex overlying ICH lesion could provide improved survival of grafted NSCs, increased angiogenesis and behavioral recovery in mouse ICH model. ICH was induced in adult mice by unilateral injection of bacterial collagenase into striatum. HB1.F3.VEGF human NSC line produced an amount of VEGF four times higher than parental F3 cell line in vitro, and induced behavioral improvement and 2-3 fold increase in cell survival at two weeks and eight weeks post-transplantation. CONCLUSIONS: Brain transplantation of F3 human NSCs over-expressing VEGF near ICH lesion sites provided differentiation and survival of grafted human NSCs and renewed angiogenesis of host brain and functional recovery of ICH animals. These results suggest a possible application of the human neural stem cell line, which is genetically modified to over-express VEGF, as a therapeutic agent for ICH-stroke.

  7. Pregnancy outcome in patients with sickle cell disease in the UK--a national cohort study comparing sickle cell anaemia (HbSS) with HbSC disease.

    Science.gov (United States)

    Oteng-Ntim, Eugene; Ayensah, Benjamin; Knight, Marian; Howard, Jo

    2015-04-01

    We describe the findings from a national study of maternal and fetal outcomes of pregnancy in women with sickle cell disease (SCD). Data were collected via the United Kingdom Obstetric Surveillance System between 1 February 2010 and 31 January 2011 from 109 women, of whom 51 (46·8%) had HbSS and 44 (40·4%) had HbSC. Data included antenatal, maternal and fetal outcomes. Comparisons were made between women with HbSS and HbSC. Incidence of complications were acute pain (57%), blood transfusion (26%), urinary tract infection (UTI; 12%) and critical care unit admission (23%) and these were all more common in women with HbSS than HbSC. There was no difference in the incidence of acute chest syndrome, hypertension and venous thromboembolism between HbSS and HbSC. Women with HbSS were more likely to deliver at pregnancy. © 2014 John Wiley & Sons Ltd.

  8. 29 CFR 570.63 - Occupations involved in the operation of paper-products machines, scrap paper balers, and paper...

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 3 2010-07-01 2010-07-01 false Occupations involved in the operation of paper-products machines, scrap paper balers, and paper box compactors (Order 12). 570.63 Section 570.63 Labor Regulations... involved in the operation of paper-products machines, scrap paper balers, and paper box compactors (Order...

  9. Muscle pathology in lower motor neuron paraplegia and h-b FES

    Directory of Open Access Journals (Sweden)

    Ugo Carraro

    2010-03-01

    Full Text Available After complete Spinal Cord Injury (SCI, causing complete disconnection between the muscle fibers and the nervous system, the denervated muscles become unexcitable with commercial electrical stimulators within several months and undergo severe atrophy and disorganization of contractile apparatus after 1-3 years. Years after the injury the surviving and regenerated myofibers are substituted with adipocytes and collagen. To counteract the progressive changes transforming muscle into an unexcitable tissue, we developed a novel therapy concept for paraplegic patients with complete lower motor neuron (LMN denervation of the lower extremities. The new stimulators for home-based functional electrical stimulation (h-b FES have been designed to reverse longstanding and severe atrophy of LMN denervated muscles by delivering high-intensity (up to 2,4 J and long-duration impulses (up to 150 ms able to elicit contractions of denervated skeletal muscle fibers in absence of nerve. Concurrent to the development of the stimulation equipment, specific clinical assessments and training strategies were developed at the Wilhelminenspital Wien, Austria. Main results of our clinical study on 20 patients, which completed a 2 years h-b FES program are: 1. significant +33% increase of muscle size and +75% of the mean diameter of muscle fibers, with striking improvements of the ultra-structural organization of contractile material; 2. recovery of the tetanic contractility with significant increase in muscle force output during electrical stimulation; 3. five subjects performed FES-assisted stand-up and stepping-in-place exercises;. 4. data from ultrastructural analyses indicating that the shorter the time span between SCI and the beginning of h-b FES, the larger were the number and the size of recovered fibers. The study demonstrates that h-b FES of permanent LMN denervated muscle is an effective home therapy that results in rescue of muscle mass, function and perfusion

  10. Characterization of Hb Lepore variants in the UK population.

    Science.gov (United States)

    Guo, Lina; Kausar, Anika; Old, John M; Henderson, Shirley J; Gallienne, Alice E

    2015-01-01

    A molecular study of Hb Lepore heterozygotes identified by the UK population screening program has revealed four out of the five known Lepore variants. The region of homologous δ- and β-globin gene sequence was determined in 58 unrelated Hb Lepore heterozygotes referred for confirmation of their carrier status by DNA analysis through the national thalassemia and sickle cell screening program over a period of 10 years. The most common variant found was Hb Lepore-Boston-Washington (Hb LBW, HBD: c.265 C > c.315 + 7 C) observed in 46 carriers (79.0%). Hb Lepore-Hollandia (HBD: c.69 A > c.92 + 16 A) was found in nine cases (16.0%); Hb Lepore-Baltimore (HBD: c.208 G > c.254 C) in two cases (4.0%) and Hb Lepore-ARUP (HBD: c.97 C > c.150 C) in one carrier (2.0%). Analysis of the hematological findings showed no significant differences between the four groups. The wide range of Hb Lepore variants observed in this study confirms the very diverse range of α- and β-globin gene mutations observed in the UK population by previous studies.

  11. Hb D/Talassemia beta associada à anemia crônica Hb D/ Beta thalassaemia associated with chronic anaemia

    Directory of Open Access Journals (Sweden)

    Paulo C. Naoum

    2002-03-01

    Full Text Available We describe a case of Hb D/Beta thalassemia associated with chronic anemia. Hematological analyses performed in a patient with chronic anemia demonstrating microcytosis and hypochromic in his erythrocytes. Specific laboratory diagnosis performed by alkaline and acid electrophoresis, and fetal determination by alkali resistance, indicated it to be Hb D associated with beta thalassemia. Analyses carried out on his family (father, mother and brother confirmed the suspected diagnosis. Hb D/Beta thalassemia is a very rare interaction in the Brazilian population, and its determination required specific laboratorial techniques and hematological analyses.

  12. Incident involving radioactive material in steel scrap

    International Nuclear Information System (INIS)

    Drabova, D.; Matzner, J.; Prouza, Z.

    1998-01-01

    In early March of 1996, a wagon with steel scrap heading from the Czech Republic to Italy was returned as a strongly contaminated material. Based on the integral dose (dose rate 650 mGy/h in front of the wagon) and spectrometric measurement and evaluation, it was concluded that an unshielded cobalt-60 source (1.6 TBq) was present. The history of the event (notification, assessment, intervention planning, intervention) is highlighted and the lesson learned from the incident is discussed. (P.A.)

  13. Evaluation of copper for divider subassembly in MCO Mark IA and Mark IV scrap fuel baskets

    International Nuclear Information System (INIS)

    Graves, C.E.

    1997-01-01

    The K Basin Spent Nuclear Fuel (SNF) Project Multi-Canister Overpack (MCO) subprojection eludes the design and fabrication of a canister that will be used to confine, contain, and maintain fuel in a critically safe array to enable its removal from the K Basins, vacuum drying, transport, staging, hot conditioning, and interim storage (Goldinann 1997). Each MCO consists of a shell, shield plug, fuel baskets (Mark IA or Mark IV), and other incidental equipment. The Mark IA intact and scrap fuel baskets are a safety class item for criticality control and components necessary for criticality control will be constructed from 304L stainless steel. It is proposed that a copper divider subassembly be used in both Mark IA and Mark IV scrap baskets to increase the safety basis margin during cold vacuum drying. The use of copper would increase the heat conducted away from hot areas in the baskets out to the wall of the MCO by both radiative and conductive heat transfer means. Thus copper subassembly will likely be a safety significant component of the scrap fuel baskets. This report examines the structural, cost and corrosion consequences associated with using a copper subassembly in the stainless steel MCO scrap fuel baskets

  14. Can the Afinion HbA1c Point-of-Care instrument be an alternative method for the Tosoh G8 in the case of Hb-Tacoma?

    Science.gov (United States)

    Lenters-Westra, Erna; Strunk, Annuska; Campbell, Paul; Slingerland, Robbert J

    2017-02-01

    Hb-variant interference when reporting HbA1c has been an ongoing challenge since HbA1c was introduced to monitor patients with diabetes mellitus. Most Hb-variants show an abnormal chromatogram when cation-exchange HPLC is used for the determination of HbA1c. Unfortunately, the Tosoh G8 generates what appears to be normal chromatogram in the presence of Hb-Tacoma, yielding a falsely high HbA1c value. The primary aim of the study was to investigate if the Afinion HbA1c point-of-care (POC) instrument could be used as an alternative method for the Tosoh G8 when testing for HbA1c in the presence of Hb-Tacoma. Whole blood samples were collected in K 2 EDTA tubes from individuals homozygous for HbA (n = 40) and heterozygous for Hb-Tacoma (n = 20). Samples were then immediately analyzed with the Afinion POC instrument. After analysis, aliquots of each sample were frozen at -80 °C. The frozen samples were shipped on dry ice to the European Reference Laboratory for Glycohemoglobin (ERL) and analyzed with three International Federation of Clinical Chemistry and Laboratory Medicine (IFCC) and National Glycohemoglobin Standardization Program (NGSP) Secondary Reference Measurement Procedures (SRMPs). The Premier Hb9210 was used as the reference method. When compared to the reference method, samples with Hb-Tacoma yielded mean relative differences of 31.8% on the Tosoh G8, 21.5% on the Roche Tina-quant Gen. 2 and 16.8% on the Afinion. The Afinion cannot be used as an alternative method for the Tosoh G8 when testing for HbA1c in the presence of Hb-Tacoma.

  15. Pyrolysis of a waste from the grinding of scrap tyres.

    Science.gov (United States)

    Fernández, A M; Barriocanal, C; Alvarez, R

    2012-02-15

    The fibres that are used to reinforce tyres can be recovered as a waste in the process of grinding of scrap tyres. In this paper beneficiation through pyrolysis is studied since the fibres are made up of polymers with a small amount of rubber because the latter is difficult to separate. The experiments were performed at three temperatures (400, 550 and 900°C) in a horizontal oven. The three products - gas, oil and char - obtained from the pyrolysis were investigated. The composition of the gas was analyzed by means of gas chromatography. The oil was studied by gas chromatography and infrared spectroscopy. The char porous structure was determined by N(2) adsorption. In addition, the topography of the chars was studied by means of scanning electron microscopy (SEM). The products resulting from the pyrolysis of the fibres were compared with those obtained from scrap rubber. Copyright © 2011 Elsevier B.V. All rights reserved.

  16. An assessment on the recycling opportunities of wastes emanating from scrap metal processing in Mauritius

    Energy Technology Data Exchange (ETDEWEB)

    Mauthoor, Sumayya, E-mail: sumayya.mauthoor@umail.uom.ac.mu [Department of Chemical and Environmental Engineering, University of Mauritius, Réduit (Mauritius); Mohee, Romeela [Professor of Chemical and Environmental Engineering, National Research Chair in Solid Waste Management, Mauritius Research Council (Mauritius); Kowlesser, Prakash [Solid Waste/Beach Management Unit, Ministry of Local Government and Outer Islands (Mauritius)

    2014-10-15

    Highlights: • Scrap metal processing wastes. • Areas of applications for slag, electric arc furnace dust, mill scale and wastewater sludge. • Waste generation factor of 349.3 kg per ton of steel produced. • Waste management model. - Abstract: This paper presents an assessment on the wastes namely slag, dust, mill scale and sludge resulting from scrap metal processing. The aim of this study is to demonstrate that there are various ways via which scrap metal processing wastes can be reused or recycled in other applications instead of simply diverting them to the landfill. These wastes are briefly described and an overview on the different areas of applications is presented. Based on the results obtained, the waste generation factor developed was 349.3 kg per ton of steel produced and it was reported that slag represents 72% of the total wastes emanating from the iron and steel industry in Mauritius. Finally the suitability of the different treatment and valorisation options in the context of Mauritius is examined.

  17. Low oxygen saturation and severe anemia in compound heterozygous Hb Louisville [β42(CD1)Phe→Leu] and Hb La Desirade [β129(H7)Ala→Val].

    Science.gov (United States)

    Kamseng, Parin; Trakulsrichai, Satariya; Trachoo, Objoon; Yimniam, Walaiporn; Panthan, Bhakbhoom; Jittorntam, Paisan; Niparuck, Pimjai; Sanguanwit, Pitsucha; Wananukul, Winai; Jindadamrongwech, Sumalee

    2017-03-01

    To investigate the cause(s) of a Thai male proband presenting low oxygen saturation by pulse oximetry (SpO 2 ) and severe anemia. As Hb variant was suspected, Hb typing was determined by high-performance liquid chromatography and capillary electrophoresis, and subsequently Hb variant was identified by DNA sequencing. Complete blood counts were performed using automated blood cell counter and oxygen saturation was measured by pulse oximetry. Proband was compound heterozygous for Hb Louisville [β42(CD1)Phe→Leu] and Hb La Desirade [β129(H7)Ala→Val]. Of the proband's two sons, one was compound heterozygous for Hb Louisville and Hb E and the other for Hb La Desirade and Hb E. The former son had similar clinical features and laboratory findings with those of the proband while the latter showed had no abnormal clinical manifestations. This the first report of compound heterozygosity of Hb Louisville and Hb La Desirade in an individual of Southeast Asian ethnicity. Hb variant identification is crucial for genetic counseling and appropriate treatment in regions where hemoglobinopathies are common.

  18. Recycling of contaminated scrap by melting 10 years of experience in Germany

    International Nuclear Information System (INIS)

    Hamm, M.; Kreh, R.; Quade, U.

    2000-01-01

    Recycling of slightly radioactively contaminated steel scrap from nuclear installations has been developed in Germany since the early 80's. 14,000 t of steel scrap were melted in the single purpose melting plant CARLA at Siempelkamp, Krefeld, up to now. As much material as possible is used for recycling to cast iron containers, shieldings or to replace iron ore in heavy concrete shieldings by iron granules. By this well developed recycling technique within the nuclear cycle radiation exposure of the general public could be avoided. Due to the max. achievable volume reduction, 80 % of final disposal volume have been saved so far. To manage the upcoming metallic waste from decommissioning of nuclear power plants, this recycling path will play an important role in the future. (authors)

  19. Phase equilibrium of the system Ag-Fe-Nd, and Nd extraction from magnet scraps using molten silver

    International Nuclear Information System (INIS)

    Takeda, O.; Okabe, T.H.; Umetsu, Y.

    2004-01-01

    To develop a new recycling process, we examined the direct extraction of neodymium (Nd) metal from Nd-Fe-B magnet scraps using molten silver (Ag) as an extraction medium. Prior to the extraction experiment, the phase equilibrium of the system Ag-Fe-Nd was investigated to estimate the theoretical extraction limit. It was observed that the Fe/Nd 2 Fe 17 mixture equilibrates with the molten Ag-Nd alloy containing 50-52 mol% Nd (57-59 mass% Nd) at 1363 K. The experimental results were in good agreement with the thermodynamic calculation based on literature values. By reacting Nd-Fe-B magnet scraps with molten silver at 1273 K, more than 90% of the neodymium in the scrap was extracted, and an Ag-Nd alloy containing 40-50 mass% Nd was obtained. The neodymium in the Ag-Nd alloy was separated from silver as Nd 2 O 3 by oxidizing the obtained alloy in air. Although the wettability of Nd 2 O 3 with molten silver caused some difficulties in the separation of neodymium from silver, molten silver is shown to be an effective medium for neodymium extraction from magnet scrap

  20. Study on incinerating method of leather scraps and recovery of chromium f om incinerated residues. Kakusetsu no nensho hoho no kento narabi ni nensho nokoribun kara no chromium no kaishu

    Energy Technology Data Exchange (ETDEWEB)

    Okamura, H. (Showa Women' s Univ., Tokyo (Japan) Tokyo Toritsu Hikaku Gijutsu Center, Tokyo (Japan)); Imai, T. (Tokyo Toritsu Hikaku Gijutsu Center, Tokyo (Japan))

    1991-11-05

    In Japan, it is the present situation that most of chromium contained side refuse generated in the leather manufacturing process are treated by means of using them for landfilling or incineration, etc. Even confining to the grownup oxhides and cowhides imported from North America, its total amount is 125,000t in terms of anhydride equivalent, hence it is estimated that about 1.14t of Cr{sub 2}O{sub 3} is discharged in the way mentioned above as a chromium tanning agent. Since Japan imports almost all chromium material from overseas, it is desirable to recover chromium from the above incinerated residues. In this article, based on the study results in the past concerning the recovery of chromium from incineration of leather scraps, an experimental furnace of the retorting two stage incineration system was experimentally built and a wet alkali scrubber and a hot water boiler utilizing combustion exhaust gas heat were installed. And by using them, the fuel condition to reduce the harmful gas component and the removal effect to be made with the scrubber, the chemical composition of the incinerated residues and its utilization, etc. were examined. As a result, by the above system, it was found that chromium could be recovered and reutilized. 9 refs., 6 figs., 6 tabs.

  1. Nitrate Anion Exchange in Pu-238 Aqueous Scrap Recovery Operations

    International Nuclear Information System (INIS)

    Pansoy-Hjelvik, M.E.; Silver, G.L.; Reimus, M.A.H.; Ramsey, K.B.

    1999-01-01

    Strong base, nitrate anion exchange (IX) is crucial to the purification of 238 Pu solution feedstocks with gross levels of impurities. This paper discusses the work involved in bench scale experiments to optimize the nitrate anion exchange process. In particular, results are presented of experiments conducted to (a) demonstrate that high levels of impurities can be separated from 238 Pu solutions via nitrate anion exchange and, (b) work out chemical pretreatment methodology to adjust and maintain 238 Pu in the IV oxidation state to optimize the Pu(IV)-hexanitrato anionic complex sorption to Reillex-HPQ resin. Additional experiments performed to determine the best chemical treatment methodology to enhance recovery of sorbed Pu from the resin, and VIS-NIR absorption studies to determine the steady state equilibrium of Pu(IV), Pu(III), and Pu(VI) in nitric acid are discussed

  2. Application of the UNECE Recommendations on Monitoring and Response Procedures for Radioactive Scrap Metal: From Theory to Practice

    Energy Technology Data Exchange (ETDEWEB)

    Magold, M.; Mansourian-Stephenson, S., E-mail: stephanie.mansourian-stephenson@unece.org [United Nations Economic Council for Europe, Geneva (Switzerland)

    2011-07-15

    The work of the United Nations Economic Commission for Europe (UNECE) in addressing the issue of radioactive material appearing inadvertently in scrap metal is summarized. After hosting several meetings of national and international representatives of the scrap metal industry and radiation protection experts, the UNECE issued recommendations in 2006 on Monitoring and Response Procedures for Radioactive Scrap Metal. Since then, the UNECE has been exploring, with its Member States, the extent to which the Recommendations have been utilized - by means of a questionnaire. In this paper the results of the questionnaire are presented and, on the basis of the results of the questionnaire, conclusions are drawn and recommendations made for international action in this field for the future. (author)

  3. Demonstration test on manufacturing steel bars for concrete reinforcement for recycling of reactor decommissioning metal scrap

    International Nuclear Information System (INIS)

    Sakurai, D.; Anabuki, Y.

    1993-01-01

    To prove the possibility of recycling the steel scrap resulting from decommissioning of a nuclear power plant, this salvaged steel would be formed into steel bars for concrete reinforcement, as the restricted use and limited use at nuclear plants. The shifting behavior of radioactive isotopes (RI) in the melting process was confirmed through the laboratory hot test using the RI. Then, the demonstration cold test for steel bars for reinforcement using the nonradioactive isotope was conducted in on-line production facilities. In this test the quality of steel bars and uniform distribution of RI were proven and material balance and operational data were obtained. These data show the recycling to steel bars for concrete reinforcement is applicable from economical and safety aspects

  4. Hb Dartmouth (HBA2: c.200T>C): An α2-Globin Gene Associated with Hb H Disease in One Homozygous Patient.

    Science.gov (United States)

    Farashi, Samaneh; Faramarzi Garous, Negin; Ashki, Mehri; Vakili, Shadi; Zeinali, Fatemah; Imanian, Hashem; Azarkeivan, Azita; Najmabadi, Hossein

    2015-01-01

    Hb H (β4) disease is caused by deletion or inactivation of three out of four α-globin genes. A high incidence of Hb H disease has been reported all over the world. There is a wide spectrum of phenotypic presentations, from clinically asymptomatic to having significant hepatosplenomegaly and requiring occasional or even regular blood transfusions, even more severe anemia, Hb Bart's (γ4) hydrops fetalis syndrome that can cause death in the affected fetuses late in gestation. We here present a case who was diagnosed with Hb H disease that represents a new genotype for this hereditary disorder. Hb Dartmouth is a variant caused by a missense mutation at codon 66 of the α2-globin gene (HBA2: c.200T>C), resulting in the substitution of leucine by proline. We here emphasize the importance of this point mutation involving Hb H disease and also the necessity for prenatal diagnosis (PND) for those who carry this point mutation in the heterozygous state.

  5. Radiation accident at Mayapuri scrap market, Delhi, 2010

    International Nuclear Information System (INIS)

    Dey, A. B.; Mohanan, S.; Damodaran, D.; Soneja, M.; Jain, N.; Mohan, A.; Vikram, N. K.; Sood, R.

    2012-01-01

    This article reports the accidental public radiation exposure in a scrap market in Delhi (India)), on March 2010. The source, a gamma unit containing Cobalt-60 pencils, was improperly disposed of by a research institution in violation of national regulations for radiation protection and safety of radioactive sources. The unit was sold off to unsuspecting scrap dealers who dismantled the equipment. This event subsequently caused the most severe radiation accident reported in India to date, resulting in seven radiation injuries and one death. The clinical course of five of the patients treated at the All India Inst. of Medical Sciences hospital, New Delhi, is summarised in this report. All five patients suffered from the haematological form of the acute radiation syndrome and local cutaneous radiation injury as well. While four patients exposed to doses between 0.6 and 2.8 Gy survived with intensive or supportive treatment, the patient with the highest exposure of 3.1 Gy died due to acute respiratory distress syndrome and multi-organ failure on Day 16 after hospitalisation. The incident highlights the current gaps in the knowledge, infrastructure and legislation in handling radioactive materials. Medical institutions need to formulate individualised triage and management guidelines to immediately respond to future public radiological accidents. (authors)

  6. Recycling of rare earths from Hg-containing fluorescent lamp scraps by solid state chlorination

    International Nuclear Information System (INIS)

    Lorenz, Tom; Froehlich, Peter; Bertau, Martin; Golon, Katja

    2015-01-01

    Solid state chlorination with NH 4 Cl comprises a method for rare earth recycling apart from pyro- or hydrometallurgical strategies. The examined partially Hg-containing fluorescent lamp scraps are rich in rare earths like La, Ce, Tb and Gd, but especially in Y and Eu. By mixing with NH 4 Cl and heating up to NH 4 Cl decomposition temperature in a sublimation reactor, Y and Eu could be transferred selectively into their respective metal chlorides with high yields. The yield and selectivity depend on temperature and the ratio of NH 4 Cl to fluorescent lamp scraps, which were varied systematically.

  7. Secondary polycythaemia in a Malay girl with homozygous Hb Tak.

    Science.gov (United States)

    Amran, H S; Aziz, M A; George, E; Mahmud, N; Lee, T Y; Md Noor, S

    2017-12-01

    Hb Tak is one of more than 200 high affinity haemoglobin variants reported worldwide. It results from the insertion of two nucleotides (AC) at the termination codon, between codon 146 and codon 147 of the beta-globin gene [Beta 147 (+AC)]. Polycythaemia is the main clinical feature although affected carriers are usually asymptomatic and do not require intervention. Several case studies in this region have reported the co-inheritance of Hb Tak with Hb E, delta beta and beta thalassaemia with one case of homozygous Hb Tak in a Thai boy. In this case report, a cluster of haemoglobin Tak was found in a family of Malay ethnic origin. Cascade family screening was conducted while investigating a 4-year old girl who presented with symptomatic polycythaemia. She had 2 previous Hb analysis done, at 7-month and 2-year-old with the diagnosis of possible Hb Q Thailand and Homozygous Hb D, respectively. Both diagnosis did not fit her clinical presentations. She was plethoric, had reduced exercise tolerance as well as cardiomyopathy. Her parents were consanguineously married and later diagnosed as asymptomatic carriers of Hb Tak. Consequently, re-analysis of the girl's blood sample revealed a homozygous state of Hb Tak. In conclusion, high oxygen affinity haemoglobin like Hb Tak should be considered in the investigation of polycythaemic patients with abnormal Hb analyses. In this case, DNA analysis was crucial in determining the correct diagnosis.

  8. Selective recovery of gold from waste mobile phone PCBs by hydrometallurgical process

    International Nuclear Information System (INIS)

    Kim, Eun-young; Kim, Min-seuk; Lee, Jae-chun; Pandey, B.D.

    2011-01-01

    Highlights: ► Selective leaching of Au from scrap mobile phone PCBs by two stage electro-generated chlorine and recovery by ion exchange. ► Copper leaching (97%) by 1st stage electro-generated leaching (ORP value Ag/AgCl ) with a minor gold (5%). ► Gold leaching (93%, ∼67 mg/L) by 2nd leaching (ORP value >1100 mV Ag/AgCl ) in 0.1 mol/L HCl at 25 °C. ► A concentrated gold solution, 6034 mg/L with 99.9% purity was obtained by ion exchange process. - Abstract: The leaching of gold from the scrap mobile phone PCBs by electro-generated chlorine as an oxidant and its recovery by ion exchange process was investigated. The leaching experiments were carried out by employing separate leaching reactor connected with the anode compartment of a Cl 2 gas generator. The leaching of gold increased with increase in temperature and initial concentration of chlorine, and was favorable even at low concentration of acid, whereas copper leaching increased with increase in concentration of acid and decrease in temperature. In a two-stage leaching process, copper was mostly dissolved (97%) in 165 min at 25 °C during the 1st stage leaching in 2.0 mol/L HCl by electro-generated chlorine at a current density of 714 A/m 2 along with a minor recovery of gold (5%). In the 2nd stage gold was mostly leached out (93% recovery, ∼67 mg/L) from the residue of the 1st stage by the electro-generated chlorine in 0.1 mol/L HCl. Gold recovery from the leach liquor by ion exchange using Amberlite XAD-7HP resin was found to be 95% with the maximum amount of gold adsorbed as 46.03 mg/g resin. A concentrated gold solution, 6034 mg/L with 99.9% purity was obtained in the ion exchange process.

  9. Selective recovery of gold from waste mobile phone PCBs by hydrometallurgical process

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Eun-young [Department of Material Science and Engineering, Penn State, University Park, PA 16802 (United States); Kim, Min-seuk [Mineral Resources Research Division, Korea Institute of Geoscience and Mineral Resources (KIGAM), Daejeon 305-350 (Korea, Republic of); Lee, Jae-chun, E-mail: jclee@kigam.re.kr [Mineral Resources Research Division, Korea Institute of Geoscience and Mineral Resources (KIGAM), Daejeon 305-350 (Korea, Republic of); Pandey, B.D. [Metal Extraction and Forming Division, National Metallurgical Laboratory (NML), Jamshedpur 831007 (India)

    2011-12-30

    Highlights: Black-Right-Pointing-Pointer Selective leaching of Au from scrap mobile phone PCBs by two stage electro-generated chlorine and recovery by ion exchange. Black-Right-Pointing-Pointer Copper leaching (97%) by 1st stage electro-generated leaching (ORP value <350 mV{sub Ag/AgCl}) with a minor gold (5%). Black-Right-Pointing-Pointer Gold leaching (93%, {approx}67 mg/L) by 2nd leaching (ORP value >1100 mV{sub Ag/AgCl}) in 0.1 mol/L HCl at 25 Degree-Sign C. Black-Right-Pointing-Pointer A concentrated gold solution, 6034 mg/L with 99.9% purity was obtained by ion exchange process. - Abstract: The leaching of gold from the scrap mobile phone PCBs by electro-generated chlorine as an oxidant and its recovery by ion exchange process was investigated. The leaching experiments were carried out by employing separate leaching reactor connected with the anode compartment of a Cl{sub 2} gas generator. The leaching of gold increased with increase in temperature and initial concentration of chlorine, and was favorable even at low concentration of acid, whereas copper leaching increased with increase in concentration of acid and decrease in temperature. In a two-stage leaching process, copper was mostly dissolved (97%) in 165 min at 25 Degree-Sign C during the 1st stage leaching in 2.0 mol/L HCl by electro-generated chlorine at a current density of 714 A/m{sup 2} along with a minor recovery of gold (5%). In the 2nd stage gold was mostly leached out (93% recovery, {approx}67 mg/L) from the residue of the 1st stage by the electro-generated chlorine in 0.1 mol/L HCl. Gold recovery from the leach liquor by ion exchange using Amberlite XAD-7HP resin was found to be 95% with the maximum amount of gold adsorbed as 46.03 mg/g resin. A concentrated gold solution, 6034 mg/L with 99.9% purity was obtained in the ion exchange process.

  10. Caltrans use of scrap tires in asphalt rubber products: a comprehensive review

    Directory of Open Access Journals (Sweden)

    Haiping Zhou

    2014-02-01

    Full Text Available The California Department of Transportation (Caltrans has been using scrap tire rubber in asphalt pavements since the 1970s in chip seals and the 1980s in rubberized hot mix asphalt(RHMA. Both the wet (field blend and dry processes were used in early trials. Caltrans has also used rubber modified binders containing both crumb rubber modifier and polymer modifier that could be manufactured at a refinery facility, a terminal blend wet process. Since the beginning of this century, Caltrans increased the use of scrap tire rubber in paving projects and invested considerable resources in developing technically sound, cost effective, and environmentally friendly strategies for using scrap tire rubber in roadway applications. By the end of year 2010, approximately 31%of all hot mix asphalt (HMA placed by Caltrans was rubberized HMA, roughly 1.2 million tons. Caltrans efforts in using asphalt rubber products were also demonstrated in its research and technology development. These included the construction of two full-scale field experiments, five warranty projects, and an accelerated pavement study using a heavy vehicle simulator. Additionally, terminal blend asphalt rubber and rubberized warm mix asphalts began to be experimented on trial basis. This paper provides a comprehensive review of Caltrans experience over four decades with asphalt rubber products. Current practices and future outlook are also discussed.

  11. Scrap metals' role in circular economy in Ghana, using Sunyani as a ...

    African Journals Online (AJOL)

    EJIRO

    quantity and economic value of scrap metals as essential part of resource ... Therefore, proper education, policy and regulatory measures are key recommendations to ... The methodology of this research includes the description of the.

  12. Kinetics of the Thermal Degradation of Granulated Scrap Tyres: a Model-free Analysis

    Directory of Open Access Journals (Sweden)

    Félix A. LÓPEZ

    2013-12-01

    Full Text Available Pyrolysis is a technology with a promising future in the recycling of scrap tyres. This paper determines the thermal decomposition behaviour and kinetics of granulated scrap tyres (GST by examining the thermogravimetric/derivative thermogravimetric (TGA/DTG data obtained during their pyrolysis in an inert atmosphere at different heating rates. The model-free methods of Friedman, Flynn-Wall-Ozawa and Coats-Redfern were used to determine the reaction kinetics from the DTG data. The apparent activation energy and pre-exponential factor for the degradation of GST were calculated. A comparison with the results obtained by other authors was made.DOI: http://dx.doi.org/10.5755/j01.ms.19.4.2947

  13. The Effectof Underwater Explosion on the Kinetics of Alkaline Leaching of Roasted Tungsten Carbide Scraps for Recycling

    OpenAIRE

    BAIK, Seung Woo; SHIBAYAMA, Atsushi; MURATA, Kenji; FUJITA, Toyohisa

    2004-01-01

    Wasted tungsten scraps are important resources for recycling, however, the mechanical recycle process of tungsten has a difficulty for recycling due to its mechanical strength. Underwater explosion fracturing technique was designed for solving this problem. The kinetics for alkaline leaching of roasted tungsten alloy scraps with different size distribution prepared by two ways of crushing technique has been investigated to evaluate the effect of the underwater explosion-crushing. The merit of...

  14. Scrap Tyre Management Pathways and Their Use as a Fuel—A Review

    Directory of Open Access Journals (Sweden)

    Amir Rowhani

    2016-10-01

    Full Text Available This article provides a review of different methods for managing waste tyres. Around 1.5 billion scrap tyres make their way into the environmental cycle each year, so there is an extreme demand to manage and mitigate the environmental impact which occurs from landfilling and burning. Numerous approaches are targeted to recycle and reuse the tyre rubber in various applications. Among them, one of the most important methods for sustainable environmental stewardship is converting tyre rubber components into bio-oil. In this study, scrap tyre management techniques including landfill, retreading, recycling, combustion, and conversion to liquid fuels was reviewed (including gasification, hydrothermal liquefaction, and pyrolysis. The effects of parameters such as reactor types, pyrolysis temperature, and catalyst on the oil, gas and solid products in pyrolysis process were investigated.

  15. Economic feasibility of radioactive scrap steel recycling

    International Nuclear Information System (INIS)

    Balhiser, R.; Rosholt, D.; Nichols, F.

    1995-01-01

    The goal of MSE's Radioactive Scrap Steel (RSS) Recycle Program is to develop practical methods for recycling RSS into useful product. This paper provides interim information about ongoing feasibility investigations that are scheduled for completion by September 1995. The project approach, major issues, and cost projections are outlined. Current information indicates that a cost effective RSS Recycling Facility can be designed, built, and in operation by 1999. The RSS team believes that high quality steel plate can be made from RSS at a conversion cost of $1500 per ton or less

  16. A method comparison study between two hemoglobinometer models (Hemocue Hb 301 and Hb 201+) to measure hemoglobin concentrations and estimate anemia prevalence among women in Preah Vihear, Cambodia.

    Science.gov (United States)

    Rappaport, A I; Karakochuk, C D; Whitfield, K C; Kheang, K M; Green, T J

    2017-02-01

    Hemoglobin (Hb) concentration is often measured in global health and nutrition surveys to determine anemia prevalence using a portable hemoglobinometer such as the Hemocue® Hb 201+. More recently, a newer model was released (Hemocue Hb 301) utilizing slightly different methods to measure Hb as compared to the older model. The objective was to measure bias and concordance between Hb concentrations using the Hemocue Hb 301 and Hb 201+ models in a rural field setting. Hemoglobin (Hb) concentration was measured using one finger prick of blood (approximately 10 μL) from 175 Cambodian women (18-49 years) using three Hemocue Hb 201+ and three Hb 301 machines. Bias and concordance were measured and plotted. Overall, mean ± SD Hb concentration was 116 ± 13 g/L using the Hb 201+ and 118 ± 12 g/L using the Hb 301; and anemia prevalence (Hb < 120 g/L) was 58% (n = 102) and 58% (n = 101), respectively. Overall bias ± SD was 2.0 ± 10.5 g/L and concordance (95% CI) was 0.63 (0.54, 0.72). Despite the 2 g/L bias detected between models, anemia prevalence was very similar in both models. The two models measured anemia prevalence comparably in this population of women in rural Cambodia. © 2016 John Wiley & Sons Ltd.

  17. Current Status of HbA1c Biosensors

    Science.gov (United States)

    Lin, Hua; Yi, Jun

    2017-01-01

    Glycated hemoglobin (HbA1c) is formed via non-enzymatic glycosylation reactions at the α–amino group of βVal1 residues in the tetrameric Hb, and it can reflect the ambient glycemic level over the past two to three months. A variety of HbA1c detection methods, including chromatography, immunoassay, enzymatic measurement, electrochemical sensor and capillary electrophoresis have been developed and used in research laboratories and in clinics as well. In this review, we summarize the current status of HbA1c biosensors based on the recognition of the sugar moiety on the protein and also their applications in the whole blood sample measurements. PMID:28777351

  18. CRITICAL ASPECTS IN SCRAPS OF COLD SMOKED SALMON PROCESSING

    Directory of Open Access Journals (Sweden)

    C. Bernardi

    2011-01-01

    Full Text Available The aim of the paper was to summarize the critical aspects in the processing of smoked salmon scraps as resulted from seven different lots of samples through microbiological and chemical-physical analysis. Results demonstrate that this product has very variable salt content, high microbial counts influencing the shelf-life, rancidity problems depending on the raw material and is heavily contaminated by Listeria monocytogenes.

  19. Structure of the AZ91 alloy pressure castings fabricated of home scrap containing charge

    Directory of Open Access Journals (Sweden)

    Z. Konopka

    2011-04-01

    Full Text Available The influence of the AZ91 alloy home scrap addition to the metal charge on both the structure and the selected mechanical propertiesof pressure castings was examined in this article. Two heats were made using different components, the first with only pure AZ91 alloyingots in the charge, and the second containing 30 wt % of home scrap. The hot chamber 3 MN machine was used for casting. Thestructures of the castings and their Brinell hardness were examined for both cases. A strong refinement of crystals was observed in castings made with the contribution of the recycled material. Any significant differences in castings hardness were not observed.

  20. Radiation protection aspects in importing metallic scraps; Problemi di radioprotezione connessi con l`importazione di rottami metallici

    Energy Technology Data Exchange (ETDEWEB)

    Risica, S.; Di Ciacco, P. [Istituto Superiore di Sanita`, Rome (Italy). Laboratorio di Fisica

    1996-09-01

    The meeting deals with radiation protection problems caused by the possibility that radioactive metal scraps or radioactive sources hidden in the scraps, may arrive in a foundry. The importance of this issue and of rational and systematic solutions is showed by several accidents, happened in the past in numerous countries, by many signals in Italy and by some papers published in international scientific journals or reports issued by authorities and institutions in different countries.

  1. Mathematical Modeling and Algebraic Technique for Resolving a Single-Producer Multi-Retailer Integrated Inventory System with Scrap

    OpenAIRE

    Yuan-Shyi Peter Chiu; Chien-Hua Lee; Nong Pan; Singa Wang Chiu

    2013-01-01

    This study uses mathematical modeling along with an algebraic technique to resolve the production-distribution policy for a single-producer multi-retailer integrated inventory system with scrap in production. We assume that a product is manufactured through an imperfect production process where all nonconforming items will be picked up and scrapped in each production cycle. After the entire lot is quality assured, multiple shipments will be delivered synchronously to m different retailers in ...

  2. HB D Los Angeles in a Brazilian family Hb D Los Angeles em família brasileira

    Directory of Open Access Journals (Sweden)

    Guilherme G. Leoneli

    2001-09-01

    Full Text Available Inherited disorders of hemoglobin, the most common monogenic disease, are now well understood at the molecular level, knowledge, which has led to considerable improvements in their control and management. The Brazilian population is multiethnic, and the correct characterization of the Hb D is important, mainly because the method available for detection of abnormal hemoglobins, present a migration in the same zone at alkaline pH, for Hb S, D, and G for example. In this paper we studied a family with an abnormal hemoglobin like S in alkaline electrophoresis, by appropriated methods including HPLC and molecular analysis, characterized as hemoglobin D Los Angeles.As doenças hereditária da hemoglobina são as mais comuns doenças monogênicas e atualmente bem conhecidas do ponto de vista molecular, fato este que propiciou um avanço no seu controle e manuseio. A população brasileira caracteriza-se pela multiplicidade étnica e a caracterização da Hb D torna-se importante por este dado, associado ao fato de que os métodos de detecção das hemoglobinopatias comumente não identificam esta fração anormal que apresenta a peculiaridade de migração eletroforéticia em pH alcalino na mesma zona observada nas Hb S e G. Neste relato é apresentado um estudo familiar no qual é empregada metodologia adequada, o HLPC, que permite a identificação da Hb D.

  3. Development of on-line monitoring device to detect the presence/absence of sodium vapor

    International Nuclear Information System (INIS)

    Wolson, R.D.; McPheeters, C.C.; Kremesec, V.J.; Kolba, V.M.

    1983-03-01

    A process is being developed by the Sodium Waste Technology Program at ANL-W to remove metallic sodium from scrap and waste. The final step in the process is the removal of residual metallic sodium by evaporation at temperatures up to 482 0 C (900 0 F) and at pressures of about 10 - 2 torr (1.3 Pa). Efficient operation of this process requires that the operators have a method to indicate the completion of the evaporation. This end point would signify when the chamber and scrap and waste is free of metallic sodium. It was determined that a measure of the vacuum was not sufficiently sensitive, and a research effort was undertaken to select an on-line monitoring device. In this effort, three promising methods were reviewed. The use of quadrupole mass spectrometer was recommended and an on-line device was designed for use in a Sodium Process Demonstration (SPD) Plant

  4. Interaction of Hb Grey Lynn (Vientiane) [α91(FG3)Leu>Phe (α1)] with Hb E [β26(B8) Glu>Lys] and α(+)-thalassemia: Molecular and Hematological Analysis.

    Science.gov (United States)

    Singha, Kritsada; Fucharoen, Goonnapa; Fucharoen, Supan

    2015-01-01

    Hemoglobin (Hb) Grey Lynn is a Hb variant caused by a mutation at codon 91 of α1-globin gene whereas Hb E is a common β-globin chain variant among Southeast Asian population. We report two hitherto undescribed conditions of Hb Grey Lynn found in Thai individuals. The study was done on two unrelated Thai subjects. Hematological parameters were recorded and Hb analysis was carried out using automated Hb analyzers. Mutations were identified by DNA analysis. Hematological features of the patients were compared with those of various forms of Hb Grey Lynn documented previously. Hb and DNA analyses identified a heterozygous Hb Grey Lynn in one patient and a double heterozygous Hb Grey Lynn and Hb E with α(+)-thalassemia in another. Interaction of α(Grey Lynn) with β(E) chains leads to the formation of a new Hb variant, namely the Hb Grey Lynn E (α(GL)2β(E)2), detectable by liquid chromatography (10.3%) but masked by Hb E on capillary electrophoresis. Interaction of these multiple globin gene defects could lead to complex hemoglobinopathies requiring combined analysis with multiple Hb analyzers followed by DNA testing to provide accurate diagnosis of the cases.

  5. Transfusion Associated Peak in Hb HPLC Chromatogram – a Case Report

    Science.gov (United States)

    Jain, Sonal; Dass, Jasmita; Pati, Hara Prasad

    2012-01-01

    High performance liquid chromatography (HPLC) and electrophoresis are commonly used to diagnose various hemoglobinopathies. However, insufficient information about the transfusion history can lead to unexpected and confusing results. We are reporting a case of Juvenile myelomonocytic leukemia (JMML) in which HbHPLC was done to quantify fetal hemoglobin (HbF). The chromatogram showed elevated HbF along with a peak in the HbD window. A transfusion acquired peak was suspected based on the unexpectedly low percentage of HbD and was subsequently confirmed using parental HbHPLC. PMID:22348188

  6. Leaching kinetics of cobalt from the scraps of spent aerospace magnetic materials.

    Science.gov (United States)

    Zhou, Xuejiao; Chen, Yongli; Yin, Jianguo; Xia, Wentang; Yuan, Xiaoli; Xiang, Xiaoyan

    2018-06-01

    Based on physicochemical properties of the scraps of spent aerospace magnetic materials, a roasting - magnetic separation followed by sulfuric acid leaching process was proposed to extract cobalt. Roasting was performed at 500 °C to remove organic impurity. Non-magnetic impurities were reduced by magnetic separation and then the raw material was sieved into desired particle sizes. Acid leaching was carried out to extract cobalt from the scraps and experimental parameters included agitation speed, particle size, initial concentration of sulfuric acid and temperature. Agitation speed higher than 300 r/min had a relatively small impact on the cobalt extraction. As the particle size reduced, the content of cobalt in the raw material decreases and the extraction of cobalt by acid leaching increased at first and decreased afterwards. Raising the initial concentration of sulfuric acid and temperature contributed to improve the cobalt extraction and the influence of temperature was more remarkable. SEM image revealed that the spent aerospace magnetic materials mainly existed in the sliced strip flake with a loose surface and porous structure. Under the experimental condition, the leaching rate of cobalt from the scraps in sulfuric acid solution could be expressed as ln(-ln(1 - α)) = lnk + nlnt. The apparent activation energy was found to be 38.33 kJ/mol and it was mainly controlled by the surface chemical reaction. Copyright © 2018 Elsevier Ltd. All rights reserved.

  7. Hb H Hydrops Fetalis Syndrome Caused by Association of the - -(SEA) Deletion and Hb Constant Spring (HBA2: c.427T > C) Mutation in a Chinese Family.

    Science.gov (United States)

    He, Sheng; Zheng, Chenguang; Meng, Dahua; Chen, Rongyu; Zhang, Qiang; Tian, Xiaoxian; Chen, Shaoke

    2015-01-01

    Hb Constant Spring (Hb CS; HBA2: c.427T > C) is an unstable hemoglobin (Hb) variant that results from a nucleotide substitution at the termination codon of the α2-globin gene. Compound heterozygosity for α(0)-thalassemia (α(0)-thal) and Hb CS (- -(SEA)/α(CS)α) results in Hb H/Hb CS disease, which is generally characterized with mild hemolytic anemia, jaundice, and splenomegaly. Here, we describe one case with Hb H/Hb CS disease that presented with fetal anemia and fetal hydrops, known as Hb H (β4) hydrops fetalis. This is the first report of fetal hydrops caused by association of the - -(SEA) deletion and the α(CS)α mutation. Our study highlights the significance of watchful observation using a serial ultrasound method and care of pregnant women who have fetuses found to carry Hb H/Hb CS disease during pregnancy, to guard against the occurrence of fetal hydrops.

  8. Analysis and Design of Timing Recovery Schemes for DMT Systems over Indoor Power-Line Channels

    Directory of Open Access Journals (Sweden)

    Cortés José Antonio

    2007-01-01

    Full Text Available Discrete multitone (DMT modulation is a suitable technique to cope with main impairments of broadband indoor power-line channels: spectral selectivity and cyclic time variations. Due to the high-density constellations employed to achieve the required bit-rates, synchronization issues became an important concern in these scenarios. This paper analyzes the performance of a conventional DMT timing recovery scheme designed for linear time-invariant (LTI channels when employed over indoor power lines. The influence of the channel cyclic short-term variations and the sampling jitter on the system performance is assessed. Bit-rate degradation due to timing errors is evaluated in a set of measured channels. It is shown that this synchronization mechanism limits the system performance in many residential channels. Two improvements are proposed to avoid this end: a new phase error estimator that takes into account the short-term changes in the channel response, and the introduction of notch filters in the timing recovery loop. Simulations confirm that the new scheme eliminates the bit-rate loss in most situations.

  9. The prospect for recycle of radioactive scrap metals to products for restricted and unrestricted use

    International Nuclear Information System (INIS)

    Liby, A.L.

    1995-01-01

    Large quantities of radioactive scrap metals will arise from decontamination and decommissioning of nuclear power plants and DOE facilities. Much of this metal can be easily decontaminated and released to the existing secondary metals industry for recycling. For metal that can not be readily released, recycle into restricted-use end products is an economically attractive alternative to burial as low level radioactive waste. This paper will examine sources and types of scrap metal, technical approaches, potential products, and economics of metals recycle. Construction, licensing, environmental compliance, and possible reuse of existing nuclear facilities for metals recycling will be discussed. (author)

  10. Reuse of waste water from high pressure water jet decontamination for reactor decommissioning scrap metal

    International Nuclear Information System (INIS)

    Deng Junxian; Li Xin; Hou Huijuan

    2011-01-01

    For recycle and reuse of reactor decommissioning scrap metal by high pressure water jet decontamination, large quantity of radioactive waste water will be generated. To save the cost of radioactive waste water treatment and to reduce the cost of the scrap decontamination, this part of radioactive waste water should be reused. Most of the radioactivities in the decontamination waste water come from the solid particle in the water. Thus to reuse the waste water, the solid particle in the waster should be removed. Different possible treatment technologies have been investigated. By cost benefit analysis the centrifugal separation technology is selected. (authors)

  11. Survival rate and expression of Heat-shock protein 70 and Frost genes after temperature stress in Drosophila melanogaster lines that are selected for recovery time from temperature coma.

    Science.gov (United States)

    Udaka, Hiroko; Ueda, Chiaki; Goto, Shin G

    2010-12-01

    In this study, we investigated the physiological mechanisms underlying temperature tolerance using Drosophila melanogaster lines with rapid, intermediate, or slow recovery from heat or chill coma that were established by artificial selection or by free recombination without selection. Specifically, we focused on the relationships among their recovery from heat or chill coma, survival after severe heat or cold, and survival enhanced by rapid cold hardening (RCH) or heat hardening. The recovery time from heat coma was not related to the survival rate after severe heat. The line with rapid recovery from chill coma showed a higher survival rate after severe cold exposure, and therefore the same mechanisms are likely to underlie these phenotypes. The recovery time from chill coma and survival rate after severe cold were unrelated to RCH-enhanced survival. We also examined the expression of two genes, Heat-shock protein 70 (Hsp70) and Frost, in these lines to understand the contribution of these stress-inducible genes to intraspecific variation in recovery from temperature coma. The line showing rapid recovery from heat coma did not exhibit higher expression of Hsp70 and Frost. In addition, Hsp70 and Frost transcription levels were not correlated with the recovery time from chill coma. Thus, Hsp70 and Frost transcriptional regulation was not involved in the intraspecific variation in recovery from temperature coma. Copyright © 2010 Elsevier Ltd. All rights reserved.

  12. How does CKD affect HbA1c?

    Science.gov (United States)

    Bloomgarden, Zachary; Handelsman, Yehuda

    2018-04-01

    HOW DOES CHRONIC KIDNEY DISEASE AFFECT HBA1C?: A number of factors determine HbA1c other than the level of glucose exposure alone. In an subset analysis of the Atherosclerosis Risk in Communities study of 941 diabetic people with varying degrees of chronic kidney disease (CKD), as well as 724 who did not have CKD, and mean age in the eighth decade, Jung et al. ask whether HbA1c is reliable as an indicator of glycemia in people with kidney disease (CKD) to the same degree as in those not having kidney disease, and, if not, whether measures of glycated serum proteins may be more useful. The only available measure of glycemia for comparison was a single fasting glucose level, and the authors acknowledge that this gives an incomplete measure, particularly in people with relatively mild diabetes, whose mean HbA1c was 6.4%, with most having levels of 7.5% or lower. In patients of this sort, postprandial glucose levels may better explain variations in mean HbA1c. Recognizing that the dataset may be limited, Jung et al. nevertheless give an intriguingly negative answer to the first question, of the reliability of HbA1c with kidney disease. Using Deming regression analysis, Jung et al. showed that the correlation between HbA1c and fasting glucose weakens as renal function worsens, and, moreover, that this appears particularly to be the case in people with anemia (hemoglobin men and women, respectively), confirming earlier observations. Among those diabetic people with neither anemia nor CKD, the correlation coefficient between HbA1c and fasting glucose was r = 0.70, compared with r = 0.35 among those with both anemia and very severe CKD (estimated glomerular filtration rate [eGFR] perform SMBG to more adequately interpret HbA1c results. © 2017 Ruijin Hospital, Shanghai Jiaotong University School of Medicine and John Wiley & Sons Australia, Ltd.

  13. The sunflower transcription factor HaHB11 improves yield, biomass and tolerance to flooding in transgenic Arabidopsis plants.

    Science.gov (United States)

    Cabello, Julieta V; Giacomelli, Jorge I; Piattoni, Claudia V; Iglesias, Alberto A; Chan, Raquel L

    2016-03-20

    HaHB11 is a member of the sunflower homeodomain-leucine zipper I subfamily of transcription factors. The analysis of a sunflower microarray hybridized with RNA from HaHB11-transformed leaf-disks indicated the regulation of many genes encoding enzymes from glycolisis and fermentative pathways. A 1300bp promoter sequence, fused to the GUS reporter gene, was used to transform Arabidopsis plants showing an induction of expression after flooding treatments, concurrently with HaHB11 regulation by submergence in sunflower. Arabidopsis transgenic plants expressing HaHB11 under the control of the CaMV 35S promoter and its own promoter were obtained and these plants exhibited significant increases in rosette and stem biomass. All the lines produced more seeds than controls and particularly, those of high expression level doubled seeds yield. Transgenic plants also showed tolerance to flooding stress, both to submergence and waterlogging. Carbohydrates contents were higher in the transgenics compared to wild type and decreased less after submergence treatments. Finally, transcript levels of selected genes involved in glycolisis and fermentative pathways as well as the corresponding enzymatic activities were assessed both, in sunflower and transgenic Arabidopsis plants, before and after submergence. Altogether, the present work leads us to propose HaHB11 as a biotechnological tool to improve crops yield, biomass and flooding tolerance. Copyright © 2016 Elsevier B.V. All rights reserved.

  14. Liquid metal extraction of Nd from NdFeB magnet scrap

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Yanchen [Iowa State Univ., Ames, IA (United States)

    1999-12-10

    This research involves using molten magnesium (Mg) to remove neodymium (Nd) from NdFeB magnet scrap by diffusion. The results show that liquid metal extraction of Nd may be a viable and inexpensive method for recovering the expensive rare earth element Nd for use in Mg castings.

  15. Effects of α-Thalassemia on HbA1c Measurement.

    Science.gov (United States)

    Xu, Anping; Ji, Ling; Chen, Weidong; Xia, Yong; Zhou, Yu

    2016-11-01

    α-Thalassemia is a benign condition that is often present in patients with diabetes mellitus. Here, we evaluated the effects of different genotypes α-thalassemia on HbA 1c measurement. A total of 189 samples from nondiabetic patients were analyzed. HbA 1c analysis was performed by ion-exchange high-performance liquid chromatography, boronate affinity HPLC, immunoassay, and capillary electrophoresis. Fasting glucose, fructosamin, and HbA 2 were also performed. All samples were confirmed by genotyping for thalassemia. In patients with two or three functional α-genes, HbA 1c values were not significantly different from those of controls (P > 0.05); however, in individuals with α-thalassemia with one functional α-gene (i.e., HbH disease), HbA 1c levels were significantly different from those of controls (P 0.05). In this study, HbA 1c values in samples from individuals with two or three functional α-genes basically reflected the normal mean blood glucose level, while those in samples from individuals with one functional α-gene did not. © 2016 Wiley Periodicals, Inc.

  16. The optical emission from the supernova remnant HB 3

    Science.gov (United States)

    Fesen, R. A.; Gull, T. R.

    1983-01-01

    The supernova remnant HB 3 was first detected as a radio source by Brown and Hazard (1953). On the basis of subsequent radio studies, it was concluded that the object was a supernova remnant (SNR). HB 3 is located at the far western edge of the H II region/molecular cloud complex W3-W4-W5 (IC 1795-1805-1848). However, a physical association of HB 3 with this complex is uncertain. In the present investigation, attention is called to the probability that HB 3 exhibits a more extensive optical emission structure than previously realized, and one which agrees well with both the position and morphology of the radio emission. It is found that narrow-passband optical images strongly suggest an almost complete optical emission shell for HB 3. Spectroscopic observations are, however, required to confirm that this emission is characteristic of a SNR.

  17. Plutonium scrap waste processing based on aqueous nitrate and chloride media

    International Nuclear Information System (INIS)

    Navratil, J.D.

    1985-01-01

    A brief review of plutonium scrap aqueous waste processing technology at Rocky Flats is given. Nitric acid unit operations include dissolution and leaching, anion exchange purification and precipitation. Chloride waste processing consists of cation exchange and carbonate precipitation. Ferrite and carrier precipitation waste treatment processes are also described. 3 figs

  18. Structured education using Dose Adjustment for Normal Eating (DAFNE) reduces long-term HbA1c and HbA1c variability.

    Science.gov (United States)

    Walker, G S; Chen, J Y; Hopkinson, H; Sainsbury, C A R; Jones, G C

    2018-06-01

    Previous evidence has demonstrated that participation in the Dose Adjustment for Normal Eating (DAFNE) education programme can reduce HbA 1c and severe hypoglycaemia in people with Type 1 diabetes. In a number of studies, increased HbA 1c variability has been associated with higher diabetic morbidity and mortality. No studies have examined the impact of structured education on HbA 1c variability in Type 1 diabetes. People with Type 1 diabetes who had attended DAFNE were identified for inclusion from the Scottish Care Information-Diabetes dataset. HbA 1c median and variability, expressed as coefficient of variation (CV) before and after DAFNE was calculated. Some 1061 individuals participated in DAFNE education and 687 met the inclusion criteria. A significant median reduction in HbA 1c [-3.5 mmol/mol (-0.3%)] was seen at 12 months with a significant reduction [-1.5 mmol/mol (-0.1%)] still seen at 60 months of follow-up. HbA 1c variability as measured by CV was significantly lower during the post-DAFNE period: 0.08 (IQR 0.05-0.12) reduced to 0.07 (IQR 0.05-0.10); P = 0.002. The data confirm that DAFNE participation improves glycaemic control in Type 1 diabetes with benefits being sustained for 5 years. This study is the first to demonstrate reduced HbA 1c variability after completion of structured education. This is new evidence of the beneficial impact of DAFNE on glycaemic profile. © 2018 Diabetes UK.

  19. Demonstration test on manufacturing 200 l drum inner shielding material for recycling of reactor operating metal scrap

    International Nuclear Information System (INIS)

    Umemura, A.; Kimura, K.; Ueno, H.

    1993-01-01

    Low-level reactor wastes should be safely recycled considering those resource values, the reduction of waste disposal volume and environmental effects. The reasonable recycling system of reactor operating metal scrap has been studied and it was concluded that the 200 liter drum inner shielding material is a very promising product for recycling within the nuclear industry. The drum inner shielding material does not require high quality and so it is expected to be easily manufactured by melting and casting from roughly sorted scrap metals. This means that the economical scrap metal recycling system can be achieved by introducing it. Furthermore its use will ensure safety because of being contained in a drum. In order to realize this recycling system with the drum inner shielding material, the demonstration test program is being conducted. The construction of the test facility, which consists of a melting and refining furnace, a casting apparatus, a machining apparatus etc., was finishing in September, 1992

  20. Synthesis of high purity tungsten nanoparticles from tungsten heavy alloy scrap by selective precipitation and reduction route

    International Nuclear Information System (INIS)

    Kamal, S.S. Kalyan; Sahoo, P.K.; Vimala, J.; Shanker, B.; Ghosal, P.; Durai, L.

    2016-01-01

    In this paper we report synthesis of tungsten nanoparticles of high purity >99.7 wt% from heavy alloy scrap using a novel chemical route of selective precipitation and reduction. The effect of Poly(vinylpyrrolidone) polymer on controlling the particle size is established through FTIR spectra and corroborated with TEM images, wherein the average size decreased form 210 to 45 nm with increasing PVP content from zero to 2 g under different experimental conditions. This process is economical as raw material is a scrap and the efficiency of the reaction is >95%. - Highlights: • Tungsten nanoparticles were synthesized from tungsten heavy alloy scrap. • A novel chemical route of precipitation and reduction with Poly(vinylpyrrolidone) polymer as stabilizer is reported. • The average size decreased form 210 to 45 nm with increasing PVP content from zero to 2 g. • High pure tungsten nanoparticles of >99.7% purity could be synthesized using this route. • Efficiency of the reaction is >95%.

  1. Exclusion, Exemption and Clearance in the Frame of the Control and Management of Inadvertent Radioactive Material in Scrap Metal

    International Nuclear Information System (INIS)

    Gonzalez, Abel J.

    2011-01-01

    Radioactive substances are incorporated into materials, goods, merchandises, products and in scrap and, as scrap would recycle into new produce, the process of introduction of radioactive susbtanaces into commodities will continue. The situation is unstoppable and requires straightforward solutions. The problem is global and therefore the solution(s) should be global. A clear intergovernmental agreement is needed establishing to what extent commodities should be regulated

  2. Complex Interaction of Hb Q-Thailand (HBA1: c.223G>C) with β-Thalassemia/Hb E (HBB: c.79G>A) Disease.

    Science.gov (United States)

    Panyasai, Sitthichai; Satthakarn, Surada; Pornprasert, Sakorn

    2018-01-01

    Hb Q-Thailand [α74(EF3)Asp→His (α1), GAC>CAC, HBA1: c.223G>C] is an abnormal hemoglobin (Hb) frequently found in Thailand and Southeast Asian countries. The association of the α Q-Thailand allele with other globin gene disorders has important implications in diagnosis. Here, we report how to diagnose the coinheritance of Hb Q-Thailand with β-thalassemia (β-thal)/Hb E disease in four Thai samples from high performance liquid chromatography (HPLC) and capillary electrophoresis (CE) testing results. Understanding of the HPLC chromatogram and CE electropherogram patterns of this complex mutation is important for interpretation of testing results and providing genetic counseling.

  3. The heparin-binding domain of HB-EGF mediates localization to sites of cell-cell contact and prevents HB-EGF proteolytic release

    Energy Technology Data Exchange (ETDEWEB)

    Prince, Robin N.; Schreiter, Eric R.; Zou, Peng; Wiley, H. S.; Ting, Alice Y.; Lee, Richard T.; Lauffenburger, Douglas A.

    2010-07-01

    Heparin-binding EGF-like growth factor (HB-EGF) is a ligand for EGF receptor (EGFR) and possesses the ability to signal in juxtacrine, autocrine and/or paracrine mode, with these alternatives being governed by the degree of proteolytic release of the ligand. Although the spatial range of diffusion of released HB-EGF is restricted by binding heparan-sulfate proteoglycans (HSPGs) in the extracellular matrix and/or cellular glycocalyx, ascertaining mechanisms governing non-released HB-EGF localization is also important for understanding its effects. We have employed a new method for independently tracking the localization of the extracellular EGFlike domain of HB-EGF and the cytoplasmic C-terminus. A striking observation was the absence of the HB-EGF transmembrane proform from the leading edge of COS-7 cells in a wound-closure assay; instead, this protein localized in regions of cell-cell contact. A battery of detailed experiments found that this localization derives from a trans interaction between extracellular HSPGs and the HBEGF heparin-binding domain, and that disruption of this interaction leads to increased release of soluble ligand and a switch in cell phenotype from juxtacrine-induced growth inhibition to autocrine-induced proliferation. Our results indicate that extracellular HSPGs serve to sequester the transmembrane pro-form of HB-EGF at the point of cell-cell contact, and that this plays a role in governing the balance between juxtacrine versus autocrine and paracrine signaling.

  4. The Hb E (HBB: c.79G>A), Mean Corpuscular Volume, Mean Corpuscular Hemoglobin Cutoff Points in Double Heterozygous Hb E/- -SEA α-Thalassemia-1 Carriers are Dependent on Hemoglobin Levels.

    Science.gov (United States)

    Leckngam, Prapapun; Limweeraprajak, Ektong; Kiewkarnkha, Tiemjan; Tatu, Thanusak

    2017-01-01

    Identifying double heterozygosities in Hb E (HBB: c.79 G>A)/- - SEA (Southeast Asian) (α-thalassemia-1) (α-thal-1) in patients first diagnosed as carrying Hb E is important in thalassemia control. Low Hb E, mean corpuscular volume (MCV) and mean corpuscular hemoglobin (Hb) (MCH) levels have been observed in this double heterozygosity. However, the cutoff points of these parameters have never been systematically established. Here, we analyzed Hb E and red blood cell (RBC) parameters in 372 Hb E patients grouped by Hb levels, by the status of - - SEA and -α 3.7 (α-thal-2; rightward) deletions, to establish the cutoff points. Then, the established cutoff points were evaluated in 184 Hb E patients. It was found that the cutoff points of Hb E, MCV, MCH were significantly dependent on the Hb levels. In the group having Hb levels Hb E, MCV and MCH were 21.2%, 64.9 fL and 21.0 pg, respectively, and were 25.6%, 72.8 fL and 23.9 pg, respectively, in the group having Hb levels 10.0-11.9 g/dL. Finally, in the group having Hb levels ≥12.0 g/dL, the cutoff points of Hb E, MCV and MCH were 27.1%, 76.7 fL and 25.3 pg, respectively. Thus, to screen for the double heterozygous Hb E/- - SEA anomaly in patients initially diagnosed as carrying Hb E, the Hb levels must be taken into account in choosing the suitable cutoff points of these three parameters.

  5. Recovery from anemia in patients with severe aortic stenosis undergoing transcatheter aortic valve implantation--prevalence, predictors and clinical outcome

    DEFF Research Database (Denmark)

    De Backer, Ole; Arnous, Samer; Lønborg, Jacob

    2014-01-01

    INTRODUCTION: Preoperative anemia is common in patients with severe aortic stenosis undergoing transcatheter aortic valve implantation (TAVI) and has been linked to a poorer outcome--including a higher 1-year mortality. The aim of this study was to investigate the impact of successful TAVI...... on baseline anemia. METHODS: A total of 253 patients who survived at least 1 year following TAVI were included in this study. The prevalence, predictors and clinical outcome of hemoglobin (Hb)-recovery were assessed. RESULTS: The prevalence of baseline anemia was 49% (n = 124)--recovery from anemia occurred......-recovery, while blood transfusion (OR 0.31, P = 0.038) and chronic kidney disease (CKD, OR 0.33, P = 0.043) were identified as negative predictors at, respectively, one and two years after TAVI. When compared to patients without baseline anemia, those anemic patients with Hb-recovery had a similar functional...

  6. Is insulin the preferred treatment for HbA1c >9%?

    Science.gov (United States)

    Bloomgarden, Zachary

    2017-09-01

    The algorithms and guidelines of the American Association of Clinical Endocrinologists and the American Diabetes Association recommend that insulin administration be strongly considered for people with type 2 diabetes (T2D) with HbA1c levels exceeding 9.0% and 10%, respectively. Although the caveat is given in both sets of recommendations that this is particularly appropriate when patients are "symptomatic," referring to urinary frequency with increased thirst and appetite, weight loss, and ketosis, the clinical definition of such presentations may be ill-defined, and it is noteworthy that both documents consider insulin to offer particular benefit under such circumstances. However, with multiple options for glycemic treatment, it is of interest to reconsider this argument for insulin use. It should be recalled that in the UK Prospective Diabetes Study, diet alone was associated with a reduction in HbA1c from 9% to 7%. Drug-naïve people with T2D do often show surprisingly strong reductions in HbA1c with metformin-based dual-agent oral treatment approaches; a recent report showed that even with baseline HbA1c >11%, the combination of metformin with a sulfonylurea, pioglitazone, or sitagliptin was associated with reduction in HbA1c from 11.6% to 6.0%. A 32-week study of the combination of rosiglitazone with metformin in patients with mean baseline HbA1c 8.9% showed a mean HbA1c reduction of 2.3%, and an open-label cohort with baseline HbA1c 11.8% had a reduction in HbA1c to 7.8%. With metformin plus sitagliptin, a mean placebo-adjusted HbA1c reduction of 2.1% from a baseline of 8.8% was reported, with those patients with baseline HbA1c >9% having a 2.6% reduction in HbA1c, and an open-label cohort with baseline HbA1c 11.2% having a 2.9% reduction in HbA1c. Similar 2% HbA1c reductions from baseline levels of 9.1% were seen with metformin in initial combination with the sodium-glucose cotransporter 2 (SGLT2) inhibitor dapagliflozin. Although such dual oral agent

  7. Formation of hemoglobin (Hb)-octadecylamine (ODA) Langmuir-Blodgett (LB) film by spreading Hb solution directly onto subphase covered with a layer of ODA and its electrochemical property

    International Nuclear Information System (INIS)

    Yin Fan; Shin, Hoon-Kyu; Kwon, Young-Soo

    2006-01-01

    The formation of hemoglobin (Hb)-octadecylamine (ODA) Langmuir-Blotgett (LB) film by spreading Hb solution directly onto subphase covered with a layer of ODA and its electrochemical properties were studied in this paper. This method ensured better electrode activity because almost no protein was adsorbed onto electrode surface before depositing Hb-ODA monolayer onto electrode surface. The optimum equilibrium time of Hb interacted with ODA layer, the optimum protein amount spread onto subphase's interface and the optimum ionic strength and pH of subphase were obtained from the experimental results. The compressibility analyses of Hb-ODA films showed that the surface pressure of this film from liquid-expanded to liquid-condensed state ranged between 16 and 40 mN/m. Direct electron transfer of Hb immobilized on gold electrode by LB technique was observed by cyclic voltammetry. Results showed that Hb molecules still kept their electrochemical activity. The electrode with Hb-ODA LB film displayed the fastest electron transfer rate when the film transferred under the surface pressure of 35 mN/m

  8. Formation of hemoglobin (Hb)-octadecylamine (ODA) Langmuir-Blodgett (LB) film by spreading Hb solution directly onto subphase covered with a layer of ODA and its electrochemical property

    Energy Technology Data Exchange (ETDEWEB)

    Yin Fan [Department of Electrical Engineering, Dong-A University, Busan 604-714 (Korea, Republic of); Department of Chemistry, Changshu Institute of Technology, Changshu, 215500 (China); Shin, Hoon-Kyu [Department of Electrical Engineering, Dong-A University, Busan 604-714 (Korea, Republic of); Kwon, Young-Soo [Department of Electrical Engineering, Dong-A University, Busan 604-714 (Korea, Republic of)]. E-mail: yskwon@daunet.donga.ac.kr

    2006-03-21

    The formation of hemoglobin (Hb)-octadecylamine (ODA) Langmuir-Blotgett (LB) film by spreading Hb solution directly onto subphase covered with a layer of ODA and its electrochemical properties were studied in this paper. This method ensured better electrode activity because almost no protein was adsorbed onto electrode surface before depositing Hb-ODA monolayer onto electrode surface. The optimum equilibrium time of Hb interacted with ODA layer, the optimum protein amount spread onto subphase's interface and the optimum ionic strength and pH of subphase were obtained from the experimental results. The compressibility analyses of Hb-ODA films showed that the surface pressure of this film from liquid-expanded to liquid-condensed state ranged between 16 and 40 mN/m. Direct electron transfer of Hb immobilized on gold electrode by LB technique was observed by cyclic voltammetry. Results showed that Hb molecules still kept their electrochemical activity. The electrode with Hb-ODA LB film displayed the fastest electron transfer rate when the film transferred under the surface pressure of 35 mN/m.

  9. A Mosaic Expression of a Hb J-Amiens (HBB: c.54G > T; p.Lys18Asn) and its Interference with Hb A1c Analysis.

    Science.gov (United States)

    Schiemsky, Toon; Van Hoovels, Lieve; Desmet, Koen J O; Phylipsen, Marion; Harteveld, Cornelis L; Kieffer, Davy M J

    2015-01-01

    We report the case of a 56-year-old Caucasian woman in whom hemoglobinopathy screening was triggered following an aberrant Hb A1c analysis. Preliminary diagnosis of the hemoglobin (Hb) variant was obtained through cation exchange high performance liquid chromatography (HPLC) and gel electrophoresis. DNA analysis confirmed the presence of Hb J-Amiens [β17(A14)Lys→Asn; HBB: c.[54G > C or 54G > T)]. However, an unbalanced ratio between wild type and mutant signal after direct sequencing and a lower than expected percentage of this Hb variant led to the suggestion of a mosaic expression. Furthermore, different methods [capillary zone electrophoresis (CZE), cation exchange HPLC and boronate affinity] were tested to study the possible interference of this variant with Hb A1c measurements. These investigations showed a clinically relevant difference between the methods tested. Hb A1c analysis may lead to the discovery of new Hb variants or mosaicism for previously described Hb variants. This may have genetic consequences for the offspring of carriers and brings about the question of partner testing.

  10. Use of Fructosyl Peptide Oxidase for HbA1c Assay

    Science.gov (United States)

    Yonehara, Satoshi; Inamura, Norio; Fukuda, Miho; Sugiyama, Koji

    2015-01-01

    ARKRAY, Inc developed the world’s first automatic glycohemoglobin analyzer based on HPLC (1981). After that, ARKRAY developed enzymatic HbA1c assay “CinQ HbA1c” with the spread and diversification of HbA1c measurement (2007). CinQ HbA1c is the kit of Clinical Chemistry Analyzer, which uses fructosyl peptide oxidase (FPOX) for a measurement reaction. This report mainly indicates the developmental background, measurement principle, and future of the enzymatic method HbA1c reagent. PMID:25633966

  11. Description of x-ray-fluorescence (XRF) system for the Wet Scrap Development Laboratory (WSDL)

    International Nuclear Information System (INIS)

    Jedlovec, D.R.

    1981-06-01

    In support of the process control and accountability needs of the Wet Scrap Design Laboratory (WSDL), a technique utilizing X-ray Fluorescence (XRF) to determine actinide concentrations was developed and tested in FY 80, FY 81 at the General Electric Vallecitos Nuclear Center (GE-VNC). XRF analysis of uranium and plutonium solutions representative of those expected from the wet chemical processes of the WSDL was performed. This contract was to develop, test, and demonstrate control system concepts to provide a basis for an Integrated Control System (ICS) for a COPRECAL Conversion Plant. Financial support to the ICS was withdrawn before any x-ray fluorescence plutonium testing and development work could be accomplished. The following XRF testing and operation were performed at GE-VNC in FY 80, FY 81: uranium, plutonium, U/Pu testing completed September 1980; in-line testing completed October 1980; high concentration testing completed October 1980; shipment of XRF system components to W-HEDL accomplished January 1981

  12. Assessment of recycling or disposal alternatives for radioactive scrap metal

    International Nuclear Information System (INIS)

    Murphie, W.E.; Lilly, M.J. III

    1993-01-01

    The US Department of Energy, Office of Environmental Restoration and Waste Management, is participating with the Organization for Economic Cooperation and Development (OECD) is an evaluation of management alternatives for radioactive scarp metals. For this purpose, Argonne National Laboratory is assessing alternatives for radioactive scrap metals. For this purpose, Argonne National Laboratory is assessing environmental and societal implications of recycling and/or disposal process alternatives (with metal replacement). Findings will be presented in a report from the OECD Task Group. This paper focuses on the radiological risk assessment and dose estimate sensitivity analysis. A ''tiered'' concept for release categories, with and without use restrictions, is being developed. Within the tiers, different release limits may be indicated for specific groupings of radionuclides. Depending on the spectrum of radionuclides that are present and the level of residual activity after decontamination and/or smelting, the scrap may be released for unrestricted public use or for specified public uses, or it may be recycled within the nuclear industry. The conversatism of baseline dose estimates is examined, and both more realistic parameter values and protective measures for workers are suggested

  13. The Long and Winding Road to Optimal HbA1c Measurement

    Science.gov (United States)

    Little, Randie R.; Rohlfing, Curt

    2016-01-01

    The importance of hemoglobin A1c (HbA1c) as an indicator of mean glycemia and risks for complications in patients with diabetes mellitus was established by the results of long-term clinical trials, most notably the Diabetes Control and Complications Trial (DCCT) and United Kingdom Prospective Diabetes Study (UKPDS), published in 1993 and 1998 respectively. However, clinical application of recommended HbA1c targets that were based on these studies was difficult due to lack of comparability of HbA1c results among assay methods and laboratories. Thus, the National Glycohemoglobin Standardization Program (NGSP) was initiated in 1996 with the goal of standardizing HbA1c results to those of the DCCT/UKPDS. HbA1c standardization efforts have been highly successful; however, a number of issues have emerged on the “long and winding road” to better HbA1c, including the development of a higher-order HbA1c reference method by the International Federation of Clinical Chemistry (IFCC), recommendations to use HbA1c to diagnose as well as monitor diabetes, and point-of-care (POC) HbA1c testing. Here, we review the past, present and future of HbA1c standardization and describe the current status of HbA1c testing, including limitations that healthcare providers need to be aware of when interpreting HbA1c results. PMID:23318564

  14. Service recovery's impact on customers next-in-line

    OpenAIRE

    Van Vaerenbergh, Yves; Vermeir, Iris; Larivière, Bart

    2013-01-01

    Purpose - Previous research considers service recovery as a one-on-one interaction between a service provider and a complaining customer. However, customers frequently complain at the place where they receive the service, making an investigation of the impact of a service recovery on observing customers necessary. Using observational learning theory and attribution theory as theoretical anchors, this paper examines whether observing a service recovery influences the observing customers' satis...

  15. The detection and assessment of radioactive parts in scrap - a technical and legal challenge

    International Nuclear Information System (INIS)

    Rieck, W.

    1999-01-01

    According to the requirements of the European steel industry, delivery of radioactive contaminated metallurgical scrap in excess of natural level has to be excluded. Therefore, in Germany alone, more than 100 high-sensitive gate monitors were installed during the last few years at steel mills and scrap handling facilities. This has resulted in not only tighter protection from an erroneous melting of radioactive sources but also in a great increase in number of reported findings than before. Aside from a small number of sealed sources, the majority of detections concern natural radioactive scale and contamination, mostly from fission and activation products as well as traces of nuclear fuel. Practical and legal problems regarding the application of the regulations on radioactivity protection are demonstrated and discussed. (author)

  16. Recent Progress in Electrochemical HbA1c Sensors: A Review

    Directory of Open Access Journals (Sweden)

    Baozhen Wang

    2015-03-01

    Full Text Available This article reviews recent progress made in the development of electrochemical glycated hemoglobin (HbA1c sensors for the diagnosis and management of diabetes mellitus. Electrochemical HbA1c sensors are divided into two categories based on the detection protocol of the sensors. The first type of sensor directly detects HbA1c by binding HbA1c on the surface of an electrode through bio-affinity of antibody and boronic acids, followed by an appropriate mode of signal transduction. In the second type of sensor, HbA1c is indirectly determined by detecting a digestion product of HbA1c, fructosyl valine (FV. Thus, the former sensors rely on the selective binding of HbA1c to the surface of the electrodes followed by electrochemical signaling in amperometric, voltammetric, impedometric, or potentiometric mode. Redox active markers, such as ferrocene derivatives and ferricyanide/ferrocyanide ions, are often used for electrochemical signaling. For the latter sensors, HbA1c must be digested in advance by proteolytic enzymes to produce the FV fragment. FV is electrochemically detected through catalytic oxidation by fructosyl amine oxidase or by selective binding to imprinted polymers. The performance characteristics of HbA1c sensors are discussed in relation to their use in the diagnosis and control of diabetic mellitus.

  17. Slow hematological recovery in children with IBD-associated anemia in cases of "expectant management".

    Science.gov (United States)

    Pels, Lise P M; Van de Vijver, Els; Waalkens, Herman J; Uitentuis, Jan; JGonera-de ong, Gieneke; van Overbeek, Lidy A T; Norbruis, Obbe F; Rings, Edmond H H M; van Rheenen, Patrick F

    2010-12-01

    Allowing children with inflammatory bowel disease (IBD) to live with subnormal hemoglobin (Hb) levels affects their quality of life. The therapeutic approach to normalize Hb varies according to the cause of IBD-associated anemia. In exclusive iron-deficiency anemia (IDA) repletion of iron stores is obligatory, whereas controlling inflammation is the treatment of choice for anemia of chronic disease (ACD). In daily practice the focus is on control of intestinal inflammation, and spontaneous hematological recovery is awaited. The aim of the present study was to evaluate the hematological effect of "expectant management" on newly diagnosed pediatric patients with IBD with anemia. Medical records of children with IBD were reviewed. Study endpoints were the difference in Hb from the moment of IBD diagnosis (T0) to the end of the induction phase (T1), and time until normalization of Hb, stratified for the type of anemia at T0. A total of 103 children were included in the study, of whom 80 (78%) had anemia at T0. Exclusive IDA was found in 58% of them. Expectant management caused a modest increase in Hb between T0 and T1 for both types of anemia (IDA 0.4 mmol/L; ACD 0.5 mmol/L), but 65 of 80 children (81%) still had anemia at T1. The proportion of children with exclusive IDA had increased to 74%. One third of the cases initially classified as having ACD had progressed to exclusive IDA. There was no significant difference in time until normalization of Hb between children with exclusive IDA and ACD. Twelve months after IBD diagnosis 24% of the group initially diagnosed as having exclusive IDA and 50% of the ACD group were still anemic. Hematological recovery in children with IBD-associated anemia is slow with expectant management, regardless of the type of anemia at T0. Present results underline the need for a more active approach to improve Hb.

  18. Advanced technologies for decontamination and conversion of scrap metal

    International Nuclear Information System (INIS)

    Muth, T.R.; Shasteen, K.E.; Liby, A.L.

    1995-01-01

    The Department of Energy (DOE) accumulated large quantities of radioactive scrap metal (RSM) through historic maintenance activities. The Decontamination and Decommissioning (D ampersand D) of major sites formerly engaged in production of nuclear materials and manufacture of nuclear weapons will generate additional quantities of RSM, as much as 3 million tons of such metal according to a recent study. The recycling of RSM is quickly becoming appreciated as a key strategy in DOE's cleanup of contaminated sites and facilities

  19. Current status of scrap metal recycling and reuse in USA and European countries

    International Nuclear Information System (INIS)

    Matsumoto, Akira

    1997-01-01

    Recycling and reuse of natural resources has become a global issue to be pursued, but less effective without voluntary efforts from the every industries and of the individuals. In Japan, recycling and reuse of the scrap metal from dismantling of the nuclear facilities are currently noticed as a promising option and the responsible government organizations just started activities to develope the system for enabling and encouraging the nuclear facility owners to recycle their waste. Coincidently, there have been many reports published recently, which inform successful results of the method and the activities of the international organizations for the same intention. Taking this opportunity, current trends of scrap metal recycling and reuse in the experienced countries are reviewed and the proposals from IAEA, EC and OECD/NEA on the relating issues are summarized and compared in this paper. (author)

  20. Efficient One-Step Electrolytic Recycling of Low-Grade and Post-Consumer Magnesium Scrap

    Energy Technology Data Exchange (ETDEWEB)

    Adam C. Powell, IV

    2012-07-19

    Metal Oxygen Separation Technologies, Inc. (abbreviated MOxST, pronounced most) and Boston University (BU) have developed a new low-cost process for recycling post-consumer co-mingled and heavily-oxidized magnesium scrap, and discovered a new chemical mechanism for magnesium separations in the process. The new process, designated MagReGenTM, is very effective in laboratory experiments, and on scale-up promises to be the lowest-cost lowest-energy lowest-impact method for separating magnesium metal from aluminum while recovering oxidized magnesium. MagReGenTM uses as little as one-eighth as much energy as today's methods for recycling magnesium metal from comingled scrap. As such, this technology could play a vital role in recycling automotive non-ferrous metals, particularly as motor vehicle magnesium/aluminum ratios increase in order to reduce vehicle weight and increase efficiency.

  1. Ferulic acid modification enhances the anti-oxidation activity of natural Hb in vitro.

    Science.gov (United States)

    Qi, Donglai; Li, Qian; Chen, Chen; Wang, Xiang

    2018-03-13

    During the development of artificial red blood cell (RBC) substitutes, oxidation side reaction is one of the major factors that hinder the application of haemoglobin (Hb)-based oxygen carriers (HBOCs). In order to avoid oxidation toxicity, we designed and prepared natural Hb conjugated with ferulic acid (FA) via simple chemical modification. In addition, the thiol groups on Hb surface were increased via the reaction of Hb with 2-iminothiolane (2-IT) and then modified with FA for the study of anti-oxidant ability. It was showed that Hb modified with FA (FA-Hb) had similar oxygen-binding capacity to natural Hb. Moreover, the anti-oxidant ability of FA-Hb in vitro in different systems was superior to natural Hb and in proportion to the degree of modification of FA. The results indicate that FA-Hb might have the potential to serve as a novel oxygen carrier with the capacity to reduce oxidative side reaction.

  2. Stat5 phosphorylation is responsible for the excessive potency of HB-EGF.

    Science.gov (United States)

    Heo, Jeongyeon; Kim, Jae Geun; Kim, Sunghwan; Kang, Hara

    2017-12-23

    Heparin-binding EGF-like growth factor (HB-EGF) is a potent growth factor involved in wound healing and tumorigenesis. Despite the sequence similarity between HB-EGF and EGF, HB-EGF induces cellular proliferation and migration more potently than EGF. However, the differential regulation by HB-EGF and EGF has not been thoroughly elucidated. In this study, we compared signaling pathways activated by HB-EGF and EGF to understand the details of the molecular mechanism of the high potency induced by HB-EGF. HB-EGF specifically induced the phosphorylation of EGFR-Y1045 and activated Stat5, which is responsible for promoting cell proliferation, and migration. The competition of phosphorylated EGFR-Y1045 inhibited Stat5 activation and consequently lowered the effect of HB-EGF on cell proliferation, suggesting that the phosphorylation of EGFR-Y1045 is essential for the activation of Stat5. The phosphorylation of EGFR-Y1045 and Stat5 induced by HB-EGF was prevented by sequestering the heparin-binding domain, suggesting that the heparin-binding domain is critical for HB-EGF-mediated signaling and cellular responses. In conclusion, the heparin-binding domain of HB-EGF was responsible for EGFR-mediated Stat5 activation, resulting in a more potent cellular proliferation, and migration than that mediated by EGF. This molecular mechanism is useful for understanding ligand-specific EGFR signaling and developing biomedicines for wound healing or cancer therapy. © 2017 Wiley Periodicals, Inc.

  3. Transient Recovery Voltages at the Main 132kV Line Bay GIS Circuit Breaker in a Windfarm

    DEFF Research Database (Denmark)

    Arana Aristi, Iván; Okholm, J.; Holbøll, Joachim

    2011-01-01

    This paper presents the results of investigations of the Transient Recovery Voltage (TRV) across the terminals of the main 132kV Line Bay GIS circuit breaker (GIS CB) for Walney 2, second phase of the Walney Offshore Wind Farm. Several simulations were performed where the influence of different...

  4. Hb TAYBE: clinical and morphological findings IN 43 patients.

    Science.gov (United States)

    Koren, Ariel; Levin, Carina; Zalman, Luci; Palmor, Haya; Filon, Dvora; Chubar, Evgeny; Resnitzky, Peretz; Bennett, Michael

    2016-08-01

    Hereditary sequence variants in globin genes are usually silent and are rarer in α-globin chains than β-globin chains. Some may lead to an unstable protein with a hemolytic or thalassemic phenotype. Hb Taybe is an unstable α-chain hemoglobin variant caused by the deletion of a threonine residue at codon 38 or 39 of the α1 globin gene. This deletion results in a structural abnormality that affects the α1 β2 contact and the α1 β1 interface, producing a highly unstable Hb. We describe the clinical, laboratory, and morphological characteristics of 43 patients with Hb Taybe, sixteen of whom are heterozygous, eight are homozygous, and nineteen are double heterozygous for Hb Taybe and other α-gene mutations or deletions. The clinical presentation is very variable from a mild hemolytic anemia to the need for red cell transfusion. Morphological characteristics include erythroid hyperplasia, defective hemoglobin production, and dyserythropoietic features. On electron microscopy dyserythropoiesis and cytoplasmic precipitation of globin compatible optical dense material is seen. This is the largest report of Hb Taybe patients. Previous reported cohorts are not related to these cases. We conclude that patients carrying Hb Taybe have a unique hematological and clinical phenotype distinct from other hemoglobinopathies and from congenital dyserythropoietic anemia. © 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  5. The Scrap Collection per Industry Sector and the Circulation Times of Steel in the U.S. between 1900 and 2016, Calculated Based on the Volume Correlation Model

    Directory of Open Access Journals (Sweden)

    Alicia Gauffin

    2018-05-01

    Full Text Available On the basis of the Volume Correlation Model (VCM as well as data on steel consumption and scrap collection per industry sector (construction, automotive, industrial goods, and consumer goods, it was possible to estimate service lifetimes of steel in the United States between 1900 and 2016. Input data on scrap collection per industry sector was based on a scrap survey conducted by the World Steel Association for a static year in 2014 in the United States. The lifetimes of steel calculated with the VCM method were within the range of previously reported measured lifetimes of products and applications for all industry sectors. Scrapped (and apparent lifetimes of steel compared with measured lifetimes were calculated to be as follows: a scrapped lifetime of 29 years for the construction sector (apparent lifetime: 52 years compared with 44 years measured in 2014. Industrial goods: 16 (27 years compared with 19 years measured in 2010. Consumer goods: 12 (14 years compared with 13 years measured in 2014. Automotive sector: 14 (19 years compared with 17 years measured in 2011. Results show that the VCM can estimate reasonable values of scrap collection and availability per industry sector over time.

  6. Avaliação de Hb A2 e Hb F em doadores de sangue de região malarígena da Amazônia Oriental brasileira por HPLC Evaluation of Hb A2 and Hb F by HPLC in blood donors from the malaria endemic region of Eastern Amazon of Brazil

    Directory of Open Access Journals (Sweden)

    Wanessa C. Souza

    2003-01-01

    Full Text Available In malaria endemic regions of Africa, resistance to infection by Plasmodium has been observed in under 6-month-old children, when there are higher fetal hemoglobin (Hb F levels. Research performed in the São José do Rio Preto region, central-east Brazil, reported increased levels of Hb F in blood donors. The purpose of this work was to evaluate the A2 hemoglobin (Hb A2 and Hb F concentrations in blood donors deriving from the Brazilian malaria endemic region. Forty-five blood donor samples from Macapá, from patients with varying genders, ages and ethnic origins, were collected by venous puncture after informed consent was obtained. The samples were analyzed by High Performance Liquid Chromatography (HPLC - System Variant (Bio-Rad. The HPLC demonstrated sensitivity and rapidity in the identification and measurement of the hemoglobins and gave precise results. Moreover, it provided measurement of hemoglobin variants, even when they were present in small amounts, providing a diagnosis of hemoglobinopathies. Hb F levels above the normal were observed in 33.3% of the analyzed samples. The presence of increased Hb F can suggest resistance to infection by Plasmodium falciparum, as there have been reports that infected red blood cells interfere in the development of the parasite.

  7. Thrombosis in Hb Taybe [codons 38/39 (-ACC) (α1)

    DEFF Research Database (Denmark)

    Juul, Maja Bech; Vestergaard, Hanne; Petersen, Jesper

    2012-01-01

    Hb Taybe is a highly unstable hemoglobin (Hb) variant caused by a 3 bp deletion at codons 38/39 (-ACC) on the α1-globin gene. We report for the first time, a patient with a compound heterozygosity for Hb Taybe and a 5 bp deletion at the splice donor site of IVS-I on the α2-globin gene and ischemic...

  8. Challenges in the Management of Potentially Contaminated Scrap Metal

    Energy Technology Data Exchange (ETDEWEB)

    Meehan, R.W., E-mail: meehanrw@em.doe.gov [US Department of Energy, National Nuclear Security Administration, Washington, DC (United States)

    2011-07-15

    This paper describes the background and current status of the management of potentially contaminated metals and materials at the US Department of Energy (DOE) sites across the USA. The current DOE policy prohibiting the release of metal scrap for recycling from radiation areas is explained. Finally, a potential path forward to competently assess, characterize and clear material from radiological control is proposed that uses a combination of administrative processes and empirical techniques that are valid irrespective of the standard used for clearance. (author)

  9. A targetable HB-EGF-CITED4 axis controls oncogenesis in lung cancer.

    Science.gov (United States)

    Hsieh, C-H; Chou, Y-T; Kuo, M-H; Tsai, H-P; Chang, J-L; Wu, C-W

    2017-05-25

    Aberrant epidermal growth factor (EGF) receptor (EGFR) signaling contributes to neoplastic initiation and progression in lung. Mutated EGFR has become as an important therapeutic target in lung cancer, whereas targeted treatment is not available for wild-type EGFR or its ligands. In this study, we found that heparin-binding (HB)-EGF, a member of the EGF family, was highly expressed in a subset of lung cancer, proliferation of which was dependent on HB-EGF signaling. Silencing of HB-EGF with RNA interference inhibited cell cycle progression in lung cancer cells. We observed that, upon HB-EGF induction, CITED4 was induced through a signal transducer and activator of transcription 3 (STAT3)-dependent pathway, regulating cell proliferation. CITED4 interacted with MYC and potentiated MYC-mediated transactivation of the CCND1 promoter, leading to cell cycle progression. Correlation analysis revealed that HB-EGF and CITED4 were significantly positively associated in primary lung tumors, and expression of HB-EGF predicted a poor survival outcome in patients. In vitro and in vivo experiments revealed that pharmacological inhibition of HB-EGF with CRM197 significantly attenuated tumor cell growth. Thus, CITED4 functions as a molecular switch in HB-EGF-induced growth control, and HB-EGF provides a novel therapeutic target for lung cancer intervention.

  10. Status quo of energy recovery from waste in special industrial facilities and evaluation of the environmental impacts of using refuse derived fuel (RDF) in cement kilns in Germany; Untersuchung der Umweltauswirkungen des Einsatzes von Abfaellen ausserhalb thermischer Abfallbehandlungsanlagen

    Energy Technology Data Exchange (ETDEWEB)

    Alwast, H.; Marton, C.; Koepp, M.

    2001-10-01

    Within the study presented here the use of energy recovery from waste was analysed for several industrial facilities, focussing on cement plants, kilns in the lime and gypsum industry, steel works and plants for the production of non ferrous metals. 44 German cement plants dispose of an own clinker production. Presently 31 plants have a permit for recovering energy from waste. The total permitted capacity for energy recovery in German cement kilns amounts to nearly 2,6 Mio. t/a. Mainly waste oil, old tyres, fuel derived from processed production-specific and municipal waste, plastics, scrap wood and waste paper are co-incinerated. In 1998/99 a total amount of roughly 945.000 t refuse was processed in 30 units of the studied facilities. In five furnaces at three steel works waste can be used for energy or material recovery. The approved total capacity of high calorific waste for energy recovery comes to nearly 350,000 t/a. Especially industrial plastics and packaging waste from DSD, plastics processed in scrap mills and shreddered waste and granulated paint sludge are used. In 1998 the facilities processed only old plastic, representing a total amount of nearly 109.000 t. At present seven facilities in the non ferrous metal industry have a permit for energy recovery from waste. The maximum capacity amounts on national level to nearly 140.000 t/a. Especially waste oil, packaging waste, plastics and scrap wood can be processed. The analysis of respective applications of the 17th BImSchV shows an inconsistency within the amending permitting procedures. For the time to come a conformity between the respective regional permitting authorities would be recommendable. Moreover, the effects on air emission caused by using waste for energy recovery were analysed for cement kilns with own clinker production. Due to the amendment of the 17th BImSchV more stringent requirements regarding waste composition must be established. This is especially valid for the highly volatile

  11. Studies involving direct heating of uranium and plutonium oxides by microwaves

    Energy Technology Data Exchange (ETDEWEB)

    Mallik, G K; Malav, R K; Karande, A P; Bhargava, V K; Kamath, H S [Bhabha Atomic Research Centre, Tarapur (India). Advanced Fuel Fabrication Facility

    1997-08-01

    Nuclear fuel fabrication and recovery of nuclear materials from scraps generated during fabrication involve heating steps like dewaxing, sintering, roasting of scraps, calcination, etc. The dielectric properties of uranium and plutonium oxides place them in the category of materials which are susceptible to absorption of microwaves. The studies were carried out to explore the microwave heating technique for these steps required in nuclear fuel fabrication and scrap recovery laboratories. (author). 1 ref.

  12. Gained experiences concerning the treatment of radioactive metal scrap from German NPP'S in Studsvik - Gained experience concerning the treatment of radioactive metal scrap from German nuclear power plants

    International Nuclear Information System (INIS)

    Westerwinter, Boris; Buckanie, Niemma

    2014-01-01

    The company Gesellschaft fuer Nuklear-Service mbH, Essen/Germany (GNS), operates on behalf of the utilities E.ON, RWE, EnBW and VENE since the nineteen-nineties - amongst its other duties - on the waste management of metal scrap which originates from German nuclear power plants. The main objective within this responsibility is to maximize the value of recyclable fractions for re-use while minimizing the resulting radioactive waste. To achieve the aforementioned objective, melting of metallic scrap proved to be an outstanding choice. The use of this technique combined with all accompanying processes and regulations is accepted by the competent authorities and independent experts as a qualified treatment method over the entire time period. The motivation of this paper is to reflect on the experiences gained concerning the planning, implementation and results, acquired by GNS by using the Studsvik service. The focus will be on characteristics within processing of such campaigns. (authors)

  13. Mesenchymal stem cells in renal function recovery after acute kidney injury: use of a differentiating agent in a rat model.

    Science.gov (United States)

    La Manna, Gaetano; Bianchi, Francesca; Cappuccilli, Maria; Cenacchi, Giovanna; Tarantino, Lucia; Pasquinelli, Gianandrea; Valente, Sabrina; Della Bella, Elena; Cantoni, Silvia; Claudia, Cavallini; Neri, Flavia; Tsivian, Matvey; Nardo, Bruno; Ventura, Carlo; Stefoni, Sergio

    2011-01-01

    Acute kidney injury (AKI) is a major health care condition with limited current treatment options. Within this context, stem cells may provide a clinical approach for AKI. Moreover, a synthetic compound previously developed, hyaluronan monoesters with butyric acid (HB), able to induce metanephric differentiation, formation of capillary-like structures, and secretion of angiogenic cytokines, was tested in vitro. Thereafter, we investigated the effects of human mesenchymal stem cells from fetal membranes (FMhMSCs), both treated and untreated with HB, after induction of ischemic AKI in a rat model. At reperfusion following 45-min clamping of renal pedicles, each rat was randomly assigned to one of four groups: CTR, PBS, MSC, and MSC-HB. Renal function at 1, 3, 5, and 7 days was assessed. Histological samples were analyzed by light and electron microscopy and renal injury was graded. Cytokine analysis on serum samples was performed. FMhMSCs induced an accelerated renal functional recovery, demonstrated by biochemical parameters and confirmed by histology showing that histopathological alterations associated with ischemic injury were less severe in cell-treated kidneys. HB-treated rats showed a minor degree of inflammation, both at cytokine and TEM analyses. Better functional and morphological recovery were not associated to stem cells' regenerative processes, but possibly suggest paracrine effects on microenvironment that induce retrieval of renal damaged tissues. These results suggest that FMhMSCs could be useful in the treatment of AKI and the utilization of synthetic compounds could enhance the recovery induction ability of cells.

  14. Mechanosensitive promoter region in the human HB-GAM gene

    DEFF Research Database (Denmark)

    Liedert, Astrid; Kassem, Moustapha; Claes, Lutz

    2009-01-01

    Mechanical loading is essential for maintaining bone mass in the adult skeleton. However, the underlying process of the transfer of the physical stimulus into a biochemical response, which is termed mechanotransduction is poorly understood. Mechanotransduction results in the modulation of gene...... cells. Analysis of the human HB-GAM gene upstream regulatory region with luciferase reporter gene assays revealed that the upregulation of HB-GAM expression occurred at the transcriptional level and was mainly dependent on the HB-GAM promoter region most upstream containing three potential AP-1 binding...

  15. Excess HB-EGF, which promotes VEGF signaling, leads to hydrocephalus

    Science.gov (United States)

    Shim, Joon W.; Sandlund, Johanna; Hameed, Mustafa Q.; Blazer-Yost, Bonnie; Zhou, Feng C.; Klagsbrun, Michael; Madsen, Joseph R.

    2016-01-01

    Heparin binding epidermal growth factor-like growth factor (HB-EGF) is an angiogenic factor mediating radial migration of the developing forebrain, while vascular endothelial growth factor (VEGF) is known to influence rostral migratory stream in rodents. Cell migratory defects have been identified in animal models of hydrocephalus; however, the relationship between HB-EGF and hydrocephalus is unclear. We show that mice overexpressing human HB-EGF with β-galactosidase reporter exhibit an elevated VEGF, localization of β-galactosidase outside the subventricular zone (SVZ), subarachnoid hemorrhage, and ventriculomegaly. In Wistar polycystic kidney rats with hydrocephalus, alteration of migratory trajectory is detected. Furthermore, VEGF infusions into the rats result in ventriculomegaly with an increase of SVZ neuroblast in rostral migratory stream, whereas VEGF ligand inhibition prevents it. Our results support the idea that excess HB-EGF leads to a significant elevation of VEGF and ventricular dilatation. These data suggest a potential pathophysiological mechanism that elevated HB-EGF can elicit VEGF induction and hydrocephalus. PMID:27243144

  16. USING THE SCRAP TIRES TO PRODUCE A FLEXIBLE COUPLER

    OpenAIRE

    Tahsean A. Hussain

    2018-01-01

    The scrap tires considered a problematic source of waste, the old rubber tires causes a big environmental problem that is need much money and effort to disposes it safely. In Iraq there are more than two million used tires disposed to the environment annually. one of the tire’s recycling methods is the use of tire layers to produce a new rubber parts used in the engineering and industrial purposes as the bridges and machines dampers, this trend of recycling doesn’t take a sufficient care comp...

  17. Predictors of HbA1c levels in patients initiating metformin.

    Science.gov (United States)

    Martono, Doti P; Hak, Eelko; Lambers Heerspink, Hiddo; Wilffert, Bob; Denig, Petra

    2016-12-01

    The aim was to assess demographic and clinical factors as predictors of short (6 months) and long term (18 months) HbA1c levels in diabetes patients initiating metformin treatment. We conducted a cohort study including type 2 diabetes patients who received their first metformin prescription between 2007 and 2013 in the Groningen Initiative to Analyze Type 2 Diabetes Treatment (GIANTT) database. The primary outcome was HbA1c level at follow-up adjusted for baseline HbA1c; the secondary outcome was failing to achieve the target HbA1c level of 53 mmol/mol. Associations were analyzed by linear and logistic regression. Multiple imputation was used for missing data. Additional analyses stratified by dose and adherence level were conducted. The cohort included 6050 patients initiating metformin. Baseline HbA1c at target consistently predicted better HbA1c outcomes. Longer diabetes duration and lower total cholesterol level at baseline were predictors for higher HbA1c levels at 6 months. At 18 months, cholesterol level was not a predictor. Longer diabetes duration was also associated with not achieving the target HbA1c at follow-up. The association for longer diabetes duration was especially seen in patients starting on low dose treatment. No consistent associations were found for comorbidity and comedication. Diabetes duration was a relevant predictor of HbA1c levels after 6 and 18 months of follow-up in patients initiating metformin treatment. Given the study design, no causal inference can be made. Our study suggests that prompt treatment intensification may be needed in patients who have a longer diabetes duration at treatment initiation.

  18. Effect of once-weekly dulaglutide on glycated haemoglobin (HbA1c) and fasting blood glucose in patient subpopulations by gender, duration of diabetes and baseline HbA1c.

    Science.gov (United States)

    Gallwitz, Baptist; Dagogo-Jack, Samuel; Thieu, Vivian; Garcia-Perez, Luis-Emilio; Pavo, Imre; Yu, Maria; Robertson, Kenneth E; Zhang, Nan; Giorgino, Francesco

    2018-02-01

    To evaluate the efficacy and safety of dulaglutide 1.5 and 0.75 mg in patients with type 2 diabetes by subgroups of gender, duration of diabetes and baseline glycated haemoglobin (HbA1c) in the dulaglutide clinical development programme (AWARD-1 to -6 and -8 clinical trials). Change in HbA1c was analysed by gender, duration of diabetes (baseline HbA1c (baseline in weight, hypoglycaemia and gastrointestinal adverse events were evaluated for individual trials. In the pooled analysis of patients treated with dulaglutide 1.5 mg at 6 months, the reductions in HbA1c from baseline were similar across gender (men: least squares [LS] mean -1.26% [95% confidence interval {CI} -1.36, -1.16]; women: LS mean -1.33% [95% CI -1.43, -1.24]) and among duration of diabetes subgroups (baseline HbA1c ≥8.5% had greater HbA1c reductions than patients with baseline HbA1c baseline HbA1c subgroups, respectively; women had a numerically greater weight loss or less weight gain than men with both dulaglutide doses. There was no clinically meaningful difference in hypoglycaemia trends by gender or duration of diabetes. Hypoglycaemia incidence and rate were generally lower in patients with baseline HbA1c ≥8.5% than in those with baseline HbA1c, with greater HbA1c and FBG reductions in patients with a higher baseline HbA1c. Dulaglutide was well tolerated, with a safety profile similar to other glucagon-like peptide-1 receptor agonists. © 2017 John Wiley & Sons Ltd.

  19. Modeling Single-Phase PV HB-ZVR Inverter Connected to Grid

    DEFF Research Database (Denmark)

    Guo, Yougui; Zeng, Ping; Zhu, Jieqiong

    2011-01-01

    PLECS is used to model the PV H-bridge zero voltage rectifier (HB-ZVR) inverter connected to grid and good results are obtained. First, several common topologies of PV inverters are introduced. Then the unipolar PWM control strategy is described for PV HB-ZVR inverter. Third, PLECS is briefly...... introduced. Fourth, the modeling of PV HB-ZVR inverter is presented with PLECS. Finally, a series of simulations are carried out. The simulation results tell us PLECS is very powerful tool to real power circuits and it is very easy to simulate LCL filter. They have also verified that the unipolar PWM control...... strategy is feasible to control the PV HB-ZVR inverter....

  20. HB-EGF expression as a potential biomarker of acquired middle ear cholesteatoma.

    Science.gov (United States)

    Xie, Shumin; Wang, Xiaoli; Ren, Hongmiao; Liu, Xiaoyu; Ren, Jihao; Liu, Wei

    2017-08-01

    The heparin-binding epidermal growth factor-like growth factor (HB-EGF) plays an essential role in the development and invasiveness of cholesteatoma. This study may help to realize the molecular mechanisms underlying the pathogenesis of cholesteatoma and make HB-EGF a promising target for drug intervention of cholesteatoma. To detect HB-EGF expression in human surgical specimens of acquired middle ear cholesteatoma and analyze its functional role as a regulator of epithelial keratinocytes hyperproliferation. A total of 34 patients who underwent surgical treatment for middle ear cholesteatoma were recruited in the study. The mRNA and protein expression of HB-EGF in middle ear cholesteatoma tissues and normal postauricular skin tissues was investigated by real-time quantitative reverse-transcription-polymerase chain reaction (RT-qPCR), immunohistochemical staining, and western blot. The correlation between bone resorption degree and HB-EGF expression was also analyzed. On average, compared with normal postauricular skin, expression of HB-EGF mRNA in the cholesteatoma epithelium was significantly elevated 2.41-fold by RT-qPCR, and HB-EGF protein significantly upregulated 2.32-fold by western blot. Positive HB-EGF immunostaining observed in the basal and suprabasal layers of cholesteatoma epithelium was significantly stronger than in normal postauricular skin. Meanwhile, an obviously positive correlation between HB-EGF protein expression and bone resorption degree was discovered.

  1. Derivation of the human induced pluripotent stem cell line MUi017-A from a patient with homozygous Hemoglobin Constant Spring

    Directory of Open Access Journals (Sweden)

    Wasinee Wongkummool

    2017-04-01

    Full Text Available Hemoglobin Constant Spring (HbCS, HBA2: c.427T>C is a common nondeletional α-thalassemia resulting from a nucleotide substitution at the termination codon of the HBA2 gene. Homozygosity for HbCS is characterized with mild anemia, jaundice, and splenomegaly. In this study, the human induced pluripotent stem cell line MUi017-A was successfully generated from peripheral blood CD34+ hematopoietic progenitors of a 52 year old female with homozygous HbCS. The MUi017-A cell line exhibited embryonic stem cell characteristics with consistent expression of specific pluripotency markers and the capability of differentiating into the three germ layers. The cell line may be used for the disease modeling.

  2. Should Studies of Diabetes Treatment Stratification Correct for Baseline HbA1c?

    Science.gov (United States)

    Jones, Angus G.; Lonergan, Mike; Henley, William E.; Pearson, Ewan R.; Hattersley, Andrew T.; Shields, Beverley M.

    2016-01-01

    Aims Baseline HbA1c is a major predictor of response to glucose lowering therapy and therefore a potential confounder in studies aiming to identify other predictors. However, baseline adjustment may introduce error if the association between baseline HbA1c and response is substantially due to measurement error and regression to the mean. We aimed to determine whether studies of predictors of response should adjust for baseline HbA1c. Methods We assessed the relationship between baseline HbA1c and glycaemic response in 257 participants treated with GLP-1R agonists and assessed whether it reflected measurement error and regression to the mean using duplicate ‘pre-baseline’ HbA1c measurements not included in the response variable. In this cohort and an additional 2659 participants treated with sulfonylureas we assessed the relationship between covariates associated with baseline HbA1c and treatment response with and without baseline adjustment, and with a bias correction using pre-baseline HbA1c to adjust for the effects of error in baseline HbA1c. Results Baseline HbA1c was a major predictor of response (R2 = 0.19,β = -0.44,pHbA1c were associated with response, however these associations were weak or absent after adjustment for baseline HbA1c. Bias correction did not substantially alter associations. Conclusions Adjustment for the baseline HbA1c measurement is a simple and effective way to reduce bias in studies of predictors of response to glucose lowering therapy. PMID:27050911

  3. Fuzzy chance constrained linear programming model for scrap charge optimization in steel production

    DEFF Research Database (Denmark)

    Rong, Aiying; Lahdelma, Risto

    2008-01-01

    the uncertainty based on fuzzy set theory and constrain the failure risk based on a possibility measure. Consequently, the scrap charge optimization problem is modeled as a fuzzy chance constrained linear programming problem. Since the constraints of the model mainly address the specification of the product...

  4. United States copper metal and scrap use and trade patterns, 1995‒2014

    Science.gov (United States)

    Goonan, Thomas G.

    2016-06-17

    In 1995, China accounted for 10 percent of world copper consumption. By 2014, China accounted for about 49 percent of world copper consumption. This change has affected global copper and copper scrap prices, the sources of copper supply, and U.S. trade of copper-containing materials.

  5. Application and feasibility of coal fly ash and scrap tire fiber as wood wall insulation supplements in residential buildings

    Energy Technology Data Exchange (ETDEWEB)

    Van de Lindt, J.W.; Carraro, J.A.H.; Heyliger, P.R.; Choi, C. [Colorado State University, Department of Civil and Environmental Engineering, Fort Collins, CO (United States)

    2008-08-15

    Each year, nearly 55% of the fly ash (FA) produced by coal burning power plants in the United States is disposed of in landfills and ash ponds, while the amount of recycled fiber from scrap tires that is beneficially used in end-user markets is virtually negligible. This paper presents the results of a study carried out to investigate whether it might be possible to increase the thermal efficiency of a light-frame residential structure through addition of a fly ash-scrap tire fiber composite to traditional fiberglass insulation in light-frame wood residential construction. This type of construction represents more than 80% of the building stock in North America. The results of this study suggest that the fly ash-scrap tire fiber composite provides a sustainable supplement to traditional insulation that not only increases the efficiency of traditional insulation but can also help significantly reduce the environmental issues associated with disposal of these waste products. (author)

  6. Application and feasibility of coal fly ash and scrap tire fiber as wood wall insulation supplements in residential buildings

    International Nuclear Information System (INIS)

    Van de Lindt, J.W.; Carraro, J.A.H.; Heyliger, P.R.; Choi, C.

    2008-01-01

    Each year, nearly 55% of the fly ash (FA) produced by coal burning power plants in the United States is disposed of in landfills and ash ponds, while the amount of recycled fiber from scrap tires that is beneficially used in end-user markets is virtually negligible. This paper presents the results of a study carried out to investigate whether it might be possible to increase the thermal efficiency of a light-frame residential structure through addition of a fly ash-scrap tire fiber composite to traditional fiberglass insulation in light-frame wood residential construction. This type of construction represents more than 80% of the building stock in North America. The results of this study suggest that the fly ash-scrap tire fiber composite provides a sustainable supplement to traditional insulation that not only increases the efficiency of traditional insulation but can also help significantly reduce the environmental issues associated with disposal of these waste products. (author)

  7. The regulatory action in the problem of radioactive sources processed as scrap

    International Nuclear Information System (INIS)

    Truppa, Walter Adrian; Cateriano, Miguel Angel

    2005-01-01

    The loss of control of a radioactive source can result in a radiological emergency, especially if that source is treated as scrap. This paper presents a case registered in Argentina about discovery of a radioactive source of Kr-85, 9.25 GBq, used in a computer for industrial measurement of thickness. The radioactive source, without registration or identification, was registered by a portal for detection of radioactive material in the middle of the scrap that entered daily in the oven of a important steel company. From there, the Nuclear Regulatory Authority (RNA) conducted an investigation to determine the origin of the radioactive source, and in parallel made, in the laboratories of measurement, identification of radioactive material inside the source. This led to a company in financial and judicial bankruptcy, which had not notified the RNA about this situation, and also possessed, according to records, other eleven sources with similar characteristics. Finally the actions and regulatory effort allowed the localization of all the radioactive sources of this company, and its storage and deposit in an authorised repository

  8. Experiments in anodic film effects during electrorefining of scrap U-10Mo fuels in support of modeling efforts

    Energy Technology Data Exchange (ETDEWEB)

    Van Kleeck, M. [School of Nuclear Engineering, Purdue University, West Lafayette, IN 47907 (United States); Chemical Sciences and Engineering Division, Argonne National Laboratory, Argonne, IL 60439 (United States); Willit, J.; Williamson, M.A. [Chemical Sciences and Engineering Division, Argonne National Laboratory, Argonne, IL 60439 (United States); Fentiman, A.W. [School of Nuclear Engineering, Purdue University, West Lafayette, IN 47907 (United States)

    2013-07-01

    A monolithic uranium molybdenum alloy clad in zirconium has been proposed as a low enriched uranium (LEU) fuel option for research and test reactors, as part of the Reduced Enrichment for Research and Test Reactors program. Scrap from the fuel's manufacture will contain a significant portion of recoverable LEU. Pyroprocessing has been identified as an option to perform this recovery. A model of a pyroprocessing recovery procedure has been developed to assist in refining the LEU recovery process and designing the facility. Corrosion theory and a two mechanism transport model were implemented on a Mat-Lab platform to perform the modeling. In developing this model, improved anodic behavior prediction became necessary since a dense uranium-rich salt film was observed at the anode surface during electrorefining experiments. Experiments were conducted on uranium metal to determine the film's character and the conditions under which it forms. The electro-refiner salt used in all the experiments was eutectic LiCl/KCl containing UCl{sub 3}. The anodic film material was analyzed with ICP-OES to determine its composition. Both cyclic voltammetry and potentiodynamic scans were conducted at operating temperatures between 475 and 575 C. degrees to interrogate the electrochemical behavior of the uranium. The results show that an anodic film was produced on the uranium electrode. The film initially passivated the surface of the uranium on the working electrode. At high over potentials after a trans-passive region, the current observed was nearly equal to the current observed at the initial active level. Analytical results support the presence of K{sub 2}UCl{sub 6} at the uranium surface, within the error of the analytical method.

  9. ERGEBNISSE DER UNTERSUCHUNG VON HB-AL BEI 94 PATIENTEN MIT NIERENINSUFFIZIENZ

    Directory of Open Access Journals (Sweden)

    A

    1983-05-01

    Full Text Available We have qua nt i t a l ed Hb- Al ~n 125 patients . 74 pa t ient s had chronic Renal Failure . 20 of them had Diabetes wi th Renal Fai lure , 21 Diabetics and 10 patients were evaluat ed as control. We have divided the patients with Renal Failure i n 3 groups according to t heir serum c reatin i ne . Hb-Al in a ll groups "as not correlated wi th serum creat i ne. Hb-Al in Diabetic gr oup was highe r than Diabetic patients with Renal Failure . This group a lso had mor e HbA1 than t he gr oup with Renal ~ailure a nd no Diabetes ,and control group . , Hb-Al was correlated with Blood suger i n all pa t i e nt s s o we can u se"nal Failure the me a sureme nt of Hb-Al i n pati ents with Renunder Dial ys i s with gl ucose solution fo r evalua t i o n of sugar meta boli s m.  

  10. GENETIC FACTORS INFLUENCING HEMOGLOBIN F LEVEL IN β-THALASSEMIA/HB E DISEASE.

    Science.gov (United States)

    Ruangrai, Waraporn; Jindadamrongwech, Sumalee

    2016-01-01

    Genetic factors influencing Hb F content in adult red blood cells include β-thalassemia genotypes, co-inheritance of α-thalassemia traits and single nucleotide polymorphisms (SNPs). Genotyping of α- and β-thalassemia and five SNPs in β-globin gene cluster previously identified in genome-wide association studies as being markers of elevated Hb F in β-thalassemia were performed in 81 subjects diagnosed with β-thalassemia/Hb E. Hb F levels are higher (0.9-7.1 g/dl) in subjects (n = 57) with the severe compared to mild β-thalassemia (0.8-2.5 g/ dl) (n = 4) genotypes, and are similarly low (0.7-3.5 g/dl) in those (n = 15) with α-thalassemia co-inheritance. Hb F levels in non-thalassemia controls (n = 150) range from 0 to 0.15 g/dl. The presence of homozygous minor alleles of the 5 SNPs are significant indicators of β-thalassemia/Hb E individuals with high Hb F (> 4 g/dl), independent of their thalassemia genotypes. Given that re-activation of γ-globin genes leads to amelioration of β-thalassemia severity, understanding how genetic factors up-regulate Hb F production may lead to possible therapeutic interventions, genetically or pharmacologically, of this debilitating disease in the not too distant future.

  11. Method of handling of scrap lead from lead-acid batteries

    Energy Technology Data Exchange (ETDEWEB)

    Sytschev, A P; Kim, G V; Larin, V F; Sidorova, G D; Vicharev, I G; Kuur, V P; Achmetov, R S; Moiseev, G L; Maslov, V I; Kabatschek, V G

    1979-12-13

    Scrap lead and the casings of accumulators are mined and molten together in oxidixing atmosphere at a temperature of 1300 to 1500/sup 0/C. The lead oxide contained in the melt is then reduced to blue lead. Due to the combustion of the accumulator casings consisting of organic substances the fuel consumption in the melting process is reduced in accordance. The oxidizing atmosphere in the melting process is produced by use of air or oxygen.

  12. Relationship of HbA1c variability, absolute changes in HbA1c, and all-cause mortality in type 2 diabetes

    DEFF Research Database (Denmark)

    Skriver, Mette Vinther; Sandbæk, Annelli; Kristensen, Jette Kolding

    2015-01-01

    OBJECTIVE: We assessed the relationship of mortality with glycated hemoglobin (HbA1c) variability and with absolute change in HbA1c. DESIGN: A population-based prospective observational study with a median follow-up time of 6 years. METHODS: Based on a validated algorithm, 11 205 Danish individua...

  13. Study of silver removal from scrap jewellery by way of the flotation process

    Directory of Open Access Journals (Sweden)

    B. Oleksiak

    2012-01-01

    Full Text Available This article is a discussion on the proposed solution of using the fl otation process to separate metals from non-metallic components present in the scrap generated while jewellery goods are being ground. For the sake of the studies analysed, a dedicated laboratory station was established.

  14. Health physics challenges during decontamination for safe disposal of low level liquid effluent tank as inactive scrap

    International Nuclear Information System (INIS)

    Akila, R.; Sultan, Bajeer; Sarangapani, R.; Jose, M.T.

    2018-01-01

    The Low-level Liquid waste (LLW) generated during the regeneration of mixed bed column of KAMINI reactor is collected in the SS Delay Tanks located on the western side of RML building. It was proposed to dismantle and dispose the tank as solid waste. The tank weighs about 2 ton. An attempt was made to decontaminate the tank to levels below the exempt quantity so as to qualify it as scrap of unrestricted release. This is first time in IGCAR wherein a material used in a radioactive facility for storing LLW is being released as scrap of unrestricted release and this paper discusses about the same

  15. Obtaining of barium sulfate from solution formed after desulfation of the active mass of scrap lead-acid batteries

    Directory of Open Access Journals (Sweden)

    O. A. Kalko

    2014-03-01

    Full Text Available Analyses of literature data about processes for solution utilization formed after desulfation of the active mass of scrap lead-acid batteries is performed. Optimal conditions for obtaining of barium sulfate sediment from ammonium sulfate solute and chemically pure Ba(OH2×8H2O и BaCl2×2H2O were found experimentally. In laboratory the commercial barium sulfate from sulfate solutions, that are waste of recycling process of battery scrap, with application of chloride and barium hydroxide was production. The possibility of using this product were discussed.

  16. Quality- and dilution losses in the recycling of ferrous materials from end-of-life passenger cars: input-output analysis under explicit consideration of scrap quality.

    Science.gov (United States)

    Nakamura, Shinichiro; Kondo, Yasushi; Matsubae, Kazuyo; Nakajima, Kenichi; Tasaki, Tomohiro; Nagasaka, Tetsuya

    2012-09-04

    Metals can in theory be infinitely recycled in a closed-loop without any degradation in quality. In reality, however, open-loop recycling is more typical for metal scrap recovered from end-of-life (EoL) products because mixing of different metal species results in scrap quality that no longer matches the originals. Further losses occur when meeting the quality requirement of the target product requires dilution of the secondary material by adding high purity materials. Standard LCA usually does not address these losses. This paper presents a novel approach to quantifying quality- and dilution losses, by means of hybrid input-output analysis. We focus on the losses associated with the recycling of ferrous materials from end-of-life vehicle (ELV) due to the mixing of copper, a typical contaminant in steel recycling. Given the quality of scrap in terms of copper density, the model determines the ratio by which scrap needs to be diluted in an electric arc furnace (EAF), and the amount of demand for EAF steel including those quantities needed for dilution. Application to a high-resolution Japanese IO table supplemented with data on ferrous materials including different grades of scrap indicates that a nationwide avoidance of these losses could result in a significant reduction of CO(2) emissions.

  17. Metal Exposures at three U.S. electronic scrap recycling facilities.

    Science.gov (United States)

    Ceballos, Diana; Beaucham, Catherine; Page, Elena

    2017-06-01

    Many metals found in electronic scrap are known to cause serious health effects, including but not limited to cancer and respiratory, neurologic, renal, and reproductive damage. The National Institute for Occupational Safety and Health, Centers for Disease Control and Prevention performed three health hazard evaluations at electronic scrap recycling facilities in the U.S. to characterize employee exposure to metals and recommend control strategies to reduce these exposures. We performed air, surface, and biological monitoring for metals. We found one overexposure to lead and two overexposures to cadmium. We found metals on non-production surfaces, and the skin and clothing of workers before they left work in all of the facilities. We also found some elevated blood lead levels (above 10 micrograms per deciliter), however no employees at any facility had detectable mercury in their urine or exceeded 34% of the OELs for blood or urine cadmium. This article focuses on sampling results for lead, cadmium, mercury, and indium. We provided recommendations for improving local exhaust ventilation, reducing the recirculation of potentially contaminated air, using respirators until exposures are controlled, and reducing the migration of contaminants from production to non-production areas. We also recommended ways for employees to prevent taking home metal dust by using work uniforms laundered on-site, storing personal and work items in separate lockers, and using washing facilities equipped with lead-removing cleaning products.

  18. Both Autocrine Signaling and Paracrine Signaling of HB-EGF Enhance Ocular Neovascularization.

    Science.gov (United States)

    Inoue, Yuki; Shimazawa, Masamitsu; Nakamura, Shinsuke; Takata, Shinsuke; Hashimoto, Yuhei; Izawa, Hiroshi; Masuda, Tomomi; Tsuruma, Kazuhiro; Sakaue, Tomohisa; Nakayama, Hironao; Higashiyama, Shigeki; Hara, Hideaki

    2018-01-01

    The incidence of blindness is increasing because of the increase in abnormal ocular neovascularization. Anti-VEGF (vascular endothelial growth factor) therapies have led to good results, although they are not a cure for the blindness. The purpose of this study was to determine what role HB-EGF (heparin-binding epidermal growth factor-like growth factor) plays in ocular angiogenesis. We examined the role played by HB-EGF in ocular neovascularization in 2 animal models of neovascularization: laser-induced choroidal neovascularization (CNV) and oxygen-induced retinopathy. We also studied human retinal microvascular endothelial cells in culture. Our results showed that the neovascularization was decreased in both the CNV and oxygen-induced retinopathy models in HB-EGF conditional knockout mice compared with that in wild-type mice. Moreover, the expressions of HB-EGF and VEGF were increased after laser-induced CNV and oxygen-induced retinopathy, and their expression sites were located around the neovascular areas. Exposure of human retinal microvascular endothelial cells to HB-EGF and VEGF increased their proliferation and migration, and CRM-197 (cross-reactive material-197), an HB-EGF inhibitor, decreased the HB-EGF-induced and VEGF-induced cell proliferation and migration. VEGF increased the expression of HB-EGF mRNA. VEGF-dependent activation of EGFR (epidermal growth factor receptor)/ERK1/2 (extracellular signal-regulated kinase 1/2) signaling and cell proliferation of endothelial cells required stimulation of the ADAM17 (a disintegrin and metalloprotease) and ADAM12. CRM-197 decreased the grades of the fluorescein angiograms and size of the CNV areas in marmoset monkeys. These findings suggest that HB-EGF plays an important role in the development of CNV. Therefore, further investigations of HB-EGF are needed as a potential therapeutic target in the treatment of exudative age-related macular degeneration. © 2017 American Heart Association, Inc.

  19. The immunogenicity and safety of the new, Indonesian DTwP-HB-Hib vaccine compared to the DTwP/HB vaccine given with the Hib vaccine

    Directory of Open Access Journals (Sweden)

    Novilia Sjafri Bachtiar

    2017-06-01

    Full Text Available Background Haemophilus influenzae type b (Hib causes infection with predominant manifestations of pneumonia, meningitis, and other invasive diseases, occurring primarily in children aged under 2 years, particularly in infants.  The World Health Organization (WHO and Indonesian Technical Advisory Group for Immunization recommend to include the Hib vaccine into the national immunization program. The newly developed DTwP-HB-Hib combination vaccine is anticipated to be the preferred choice for Hib vaccine introduction; it is efficient, simple, and has higher coverage. Objective To evaluate the immunogenicity and safety of a new, combined Bio Farma DTwP-HB-Hib vaccine, compared to the registered Hib monovalent vaccine given simultaneously with the local DTwP-HB vaccine, when used as the primary vaccination of Indonesian infants. Methods A prospective, randomized, open-label, phase II study was conducted on the DTwP-HB-Hib vaccine compared to the Hib (registered vaccine given simultaneously with the DTwP-HB vaccine, in Bandung from July 2011 to January 2012. Infants were serially vaccinated at 6-11, 10-15, and 14-19 weeks. Serological assessments were done prior to the first vaccine dose and 28 days after the third dose. Safety was assessed from the time of first injection until 1 month after the last injection. Results Of 220 healthy infants enrolled, 211 completed the study, with 105 receiving the combined vaccine and 106 the two separate vaccines. All vaccines were well tolerated. No differences in rates of local and systemic reactions were seen between the two methods of administration. No serious adverse events were considered to be related to the vaccines. In the DTwP-HB-Hib primary-vaccination group, at least 98% of the infants reached protective levels of antibodies (seropositivity against the antigens employed in the vaccines while 96% in the control group. Conclusion The DTwP-HB-Hib combined vaccine is immunogenic and safe, as well as

  20. The significance of disulfide bonding in biological activity of HB-EGF, a mutagenesis approach

    OpenAIRE

    Hoskins, J.T.; Zhou, Z.; Harding, P.A.

    2008-01-01

    A site-directed mutagenesis approach was taken to disrupt each of 3 disulfide bonds within human HB-EGF by substituting serine for both cysteine residues that contribute to disulfide bonding. Each HB-EGF disulfide analogue (HB-EGF-Cys/Ser108/121, HB-EGF-Cys/Ser116/132, and HB-EGF-Cys/Ser134/143) was cloned under the regulation of the mouse metallothionein (MT) promoter and stably expressed in mouse fibroblasts. HB-EGF immunoreactive proteins with Mr of 6.5, 21 and 24kDa were observed from lys...

  1. Description of Three New α Variants and Four New β Variants: Hb Montluel [α110(G17)Ala → Val; HBA1: c.332C > T], Hb Cap d'Agde [α131(H14)Ser → Cys; HBA2: c.395C > G] and Hb Corsica [α100(G7)Leu → Pro; HBA1: 302T > C]; Hb Nîmes [β104(G6)Arg → Gly; HBB: c.313A > G], Hb Saint Marcellin [β112(G14)Cys → Gly; HBB: c.337T > G], Hb Saint Chamond [β80(EF4)Asn → 0; HBB: c.241_243delAAC] and Hb Dompierre [β29(B11)Gly → Arg; HBB: c.88G > C].

    Science.gov (United States)

    Renoux, Céline; Feray, Cécile; Joly, Philippe; Lacan, Philippe; Francina, Alain

    2015-01-01

    We present here seven new hemoglobin (Hb) variants identified during routine Hb analysis. All of them are caused by a missense mutation except Hb Saint Chamond, which results from an in-frame deletion of the asparagine residue at β80. All these variants are clinically silent in the heterozygous state but two of them (Hb Cap d'Agde and Hb Dompierre) may be unstable, whereas Hb Nîmes could present a very slightly elevated oxygen affinity. These data are to be confirmed by appropriate biochemical tests.

  2. Metallurgical recovery of metals from electronic waste: A review

    International Nuclear Information System (INIS)

    Cui Jirang; Zhang Lifeng

    2008-01-01

    Waste electric and electronic equipment, or electronic waste, has been taken into consideration not only by the government but also by the public due to their hazardous material contents. In the detailed literature survey, value distributions for different electronic waste samples were calculated. It is showed that the major economic driver for recycling of electronic waste is from the recovery of precious metals. The state of the art in recovery of precious metals from electronic waste by pyrometallurgical processing, hydrometallurgical processing, and biometallurgical processing are highlighted in the paper. Pyrometallurgical processing has been a traditional technology for recovery of precious metals from waste electronic equipment. However, state-of-the-art smelters are highly depended on investments. Recent research on recovery of energy from PC waste gives an example for using plastics in this waste stream. It indicates that thermal processing provides a feasible approach for recovery of energy from electronic waste if a comprehensive emission control system is installed. In the last decade, attentions have been removed from pyrometallurgical process to hydrometallurgical process for recovery of metals from electronic waste. In the paper, hydrometallurgical processing techniques including cyanide leaching, halide leaching, thiourea leaching, and thiosulfate leaching of precious metals are detailed. In order to develop an environmentally friendly technique for recovery of precious metals from electronic scrap, a critical comparison of main leaching methods is analyzed for both economic feasibility and environmental impact. It is believed that biotechnology has been one of the most promising technologies in metallurgical processing. Bioleaching has been used for recovery of precious metals and copper from ores for many years. However, limited research was carried out on the bioleaching of metals from electronic waste. In the review, initial researches on the

  3. Metallurgical recovery of metals from electronic waste: A review

    Energy Technology Data Exchange (ETDEWEB)

    Cui Jirang [Department of Materials Science and Engineering, Norwegian University of Science and Technology (NTNU), Alfred Getz vei 2, N-7491 Trondheim (Norway)], E-mail: Jirang.Cui@material.ntnu.no; Zhang Lifeng [Department of Materials Science and Engineering, Norwegian University of Science and Technology (NTNU), Alfred Getz vei 2, N-7491 Trondheim (Norway)], E-mail: zhanglife@mst.edu

    2008-10-30

    Waste electric and electronic equipment, or electronic waste, has been taken into consideration not only by the government but also by the public due to their hazardous material contents. In the detailed literature survey, value distributions for different electronic waste samples were calculated. It is showed that the major economic driver for recycling of electronic waste is from the recovery of precious metals. The state of the art in recovery of precious metals from electronic waste by pyrometallurgical processing, hydrometallurgical processing, and biometallurgical processing are highlighted in the paper. Pyrometallurgical processing has been a traditional technology for recovery of precious metals from waste electronic equipment. However, state-of-the-art smelters are highly depended on investments. Recent research on recovery of energy from PC waste gives an example for using plastics in this waste stream. It indicates that thermal processing provides a feasible approach for recovery of energy from electronic waste if a comprehensive emission control system is installed. In the last decade, attentions have been removed from pyrometallurgical process to hydrometallurgical process for recovery of metals from electronic waste. In the paper, hydrometallurgical processing techniques including cyanide leaching, halide leaching, thiourea leaching, and thiosulfate leaching of precious metals are detailed. In order to develop an environmentally friendly technique for recovery of precious metals from electronic scrap, a critical comparison of main leaching methods is analyzed for both economic feasibility and environmental impact. It is believed that biotechnology has been one of the most promising technologies in metallurgical processing. Bioleaching has been used for recovery of precious metals and copper from ores for many years. However, limited research was carried out on the bioleaching of metals from electronic waste. In the review, initial researches on the

  4. Posterior transverse interarch discrepancy on HbE β thalassemia patients

    Directory of Open Access Journals (Sweden)

    Yuniar Zen

    2011-03-01

    Full Text Available Background: One of the symptoms that often arises on thalassemia patients is disharmony dentofacial, class II skeletal malocclusion, as a result of the malrelation of maxilla and mandible. This malrelation can be affected by either maxillary bone position, dentoalveolar maxillary position, mandibular bone position, dentoalveolar mandibular position, or combinations of those components. Purpose: The study was aimed to examine whether there is posterior transverse interarch discrepancy on the HbE β thalassemia patients or not. Methods: This study is an observational research with cross-sectional design. The sample consisted of 33 HbE β thalassemia patients and 33 non-thalassemia patients as a control group aged 12–14 years. Lateral cephalogram was carried out and dental casts of maxillary and mandibular dental arches were also taken in all of those patients. Results: There was no difference between the maxillary intermolar width of the HbE β thalassemia patients and that of the normal ones, but the mandibular intermolar width of the HbE β thalassemia patients was significantly smaller than that of the normal ones. Beside that, posterior transverse interarch discrepancy of of the HbE β thalassemia patients was significantly greater than that of the normal ones, which showed great difference between maxillary and mandibular intermolar widths. Conclusion: Posterior transverse interarch discrepancy of the HbE β thalassemia patients was different from that of the normal ones. The dentofacial abnormalities on the HbE β thalassemia patients aged 12–14 years primarily was due to disporposional dentofacial growth in the vertical, sagittal, and transversal directions, especially in the posterior region.Latar belakang: Salah satu akibat yang sering timbul pada penderita talasemia adalah disharmoni dentofasial berupa maloklusi skeletal kelas II yang merupakan kelainan hubungan maksila dan mandibula. Malrelasi ini dapat dipengaruhi oleh posisi

  5. Nota sobre antígeno relacionado à hepatite (HB Ag e anticorpo (HB Ab em população do território Federal do Amapá

    Directory of Open Access Journals (Sweden)

    Hermann G. Schatzmayr

    1974-04-01

    Full Text Available 53 amostras de soro, provenientes de Ferreira Gomes, no Amapá, foram testados para antígeno HB Ag e anticorpo HB Ab, com uma positividade de 3,7% para HB Ag, sub-tipo D. Os autores acentuam a necessidade de inquéritos em populações brasileiras a fim de estabelecer os sub-tipos associados à hepatite.3,7% of 53 serum samples from healthy inhabitants of Ferreira Gomes, Amapá, were positive for HB Ag, subtype D. The authors síress the needs of surveys to deteet the prevalent types of antigens associated with viral hepatitis in different areas of Brazil.

  6. What’s in a Dog’s Breakfast? Considering the Social, Veterinary and Environmental Implications of Feeding Food Scraps to Pets Using Three Australian Surveys

    Directory of Open Access Journals (Sweden)

    Kirrilly Thompson

    2015-06-01

    Full Text Available Diverting food waste away from landfills is one way to minimise its serious environmental impact. Given that over a third of Australian households have at least one pet, the feeding of food waste to dogs constitutes one potentially significant waste diversion path. However, the proportion of dog owners that feed food waste to their pets is unknown. Moreover, there has been no investigation into any relationship between practices of feeding scraps to pets and the animals’ body condition, living arrangements (inside or outside and exercise regime. To provide some insight, this paper presents findings from three surveys across two Australian studies. The first reports both pet and dog-specific findings from two surveys within a wider food waste research project (n = 1017, establishing that 28% of respondents fed leftovers to pets as a main food waste minimization strategy, yet in only 5% of households did this constitute more than half of the household’s food scraps. This modest diversion of food scraps from landfill to feeding pets was reflected in the finding that there was no significant difference seen in the claimed level of food discards to the waste stream for households feeding food scraps to dogs and those that did not. The second—a dog owner specific study (n = 355—found that almost half (44% of respondents reported feeding table scraps to dogs. They were more likely to be females, owners of medium sized dogs, and in larger households. There was no significant difference in self-rated dogs’ body condition scores between respondents who fed table scraps to their dog and those who did not. Further multidisciplinary research is recommended to reconcile the social, veterinary and environmental risks and benefits of feeding food waste to animals.

  7. HbA1c, fasting plasma glucose and the prediction of diabetes

    DEFF Research Database (Denmark)

    Soulimane, Soraya; Simon, Dominique; Shaw, Jonathan

    2012-01-01

    With diabetes defined by HbA1c≥6.5% and/or FPG≥7.0mmol/l and/or diabetes treatment, we investigated HbA1c and fasting plasma glucose (FPG) thresholds/change-points above which the incidence of diabetes increases.......With diabetes defined by HbA1c≥6.5% and/or FPG≥7.0mmol/l and/or diabetes treatment, we investigated HbA1c and fasting plasma glucose (FPG) thresholds/change-points above which the incidence of diabetes increases....

  8. Avaliação eletroforética, cromatográfica e molecular da Hb D Los Angeles no Brasil Electrophoretical, chromatographic and molecular valuations of Hb D Los Angeles in Brazil

    Directory of Open Access Journals (Sweden)

    Ana R. Chinelato-Fernandes

    2003-01-01

    Full Text Available A variante de hemoglobina (Hb D mais comum, Hb D Los Angeles ou D Punjab, é originada de uma transversão GAA->CAA no códon 121 da globina beta; essa mutação resulta na substituição do ácido glutâmico por glutamina na proteína. É a terceira variante de hemoglobina mais freqüente da população brasileira. Como as hemoglobinas D apresentam migração similar à hemoglobina S em pH alcalino, e com a hemoglobina A em pH ácido, são necessários vários testes para o correto diagnóstico. No presente estudo objetivou-se relacionar os diferentes procedimentos laboratoriais de rotina diagnóstica, além da análise molecular, para estabelecer o perfil de Hb D Los Angeles no Brasil. Foram analisados 47 indivíduos da população brasileira com provável Hb D Los Angeles, por vários procedimentos eletroforéticos em diferentes condições de pH, além da cromatografia líquida de alta pressão, e testes moleculares para confirmação da mutação. Foram encontrados quatro tipos de combinações de hemoglobinas: 42 indivíduos portadores de hemoglobina AD Los Angeles, dois indivíduos com doença de Hb S/D Los Angeles, dois indivíduos com Hb D Los Angeles e talassemia beta e um indivíduo com Hb D Los Angeles e Hb Lepore. Os indivíduos heterozigotos para D Los Angeles são assintomáticos, entretanto, em associação com outras variantes e talassemias podem apresentar graus variáveis de manifestações clínicas. Os resultados apresentados enfatizaram a necessidade da associação de várias metodologias para a identificação da Hb D Los Angeles, além de auxiliar na elucidação de combinações raras.The most common Hb D variant, the Hb D-Los Angeles, also know as Hb D-Punjab, originates through a GAA->CAA change at the 121 codon of the beta globin gene; this mutation results in the replacement of glutamic acid for glutamine in the protein. It is the third most common hemoglobin variant in the Brazilian population. This variant has

  9. Cell model for the study of receptor and regulatory functions of human proHB-EGF

    Directory of Open Access Journals (Sweden)

    N. V. Korotkevych

    2014-08-01

    Full Text Available Developing of new models and approaches, particularly with fluorescent techniques, for investigation of intracellular transport of proHB-EGF and its ligand-receptor complexes is strongly required. In order to create a model for studying proHB-EGF functions the genetic construction pEGFP-N1-proHB-EGF, encoding proHB-EGF-EGFP which is fluorescent-labeled form of proHB-EGF with enhanced green fluorescent protein EGFP in the cytoplasmic terminus of the molecule, was obtained. Eukaryotic cells expressing fusion protein proHB-EGF-EGFP on the cell surface were obtained by transfection with pEGFP-N1-proHB-EGF. Expressed in the Vero cells proHB-EGF-EGFP could bind fluorescent derivative of nontoxic receptor-binding subunit B of diphtheria toxin mCherry-SubB. After stimulation of transfected cells with TPA (12-O-Tetradecanoylphorbol-13-acetate, proHB-EGF-EGFP formed a fluorescentl-labeled C-terminal fragment of the molecule – CTF-EGFP. Thus, the obtained genetic construction pEGFP-N1-proHB-EGF could be helpful in visualization of molecules proHB-EGF and CTF in cells, may open new possibilities for the studying of their functions, such as receptor function of proHB-EGF for diphtheria toxin, intracellular translocation of CTF and provide possibilities for natural proHB-EGF ligands search.

  10. Impact of Mean Cell Hemoglobin on Hb A1c-Defined Glycemia Status.

    Science.gov (United States)

    Rodriguez-Segade, Santiago; Garcia, Javier Rodriguez; García-López, José M; Gude, Francisco; Casanueva, Felipe F; Rs-Alonso, Santiago; Camiña, Félix

    2016-12-01

    Several hematological alterations are associated with altered hemoglobin A 1c (Hb A 1c ). However, there have been no reports of their influence on the rates of exceeding standard Hb A 1c thresholds by patients for whom Hb A 1c determination is requested in clinical practice. The initial data set included the first profiles (complete blood counts, Hb A 1c , fasting glucose, and renal and hepatic parameters) of all adult patients for whom such a profile was requested between 2008 and 2013 inclusive. After appropriate exclusions, 21844 patients remained in the study. Linear and logistic regression models were adjusted for demographic, hematological, and biochemical variables excluded from the predictors. Mean corpuscular hemoglobin (MCH) and mean corpuscular volume (MCV) correlated negatively with Hb A 1c . Fasting glucose, MCH, and age emerged as predictors of Hb A 1c in a stepwise regression that discarded sex, hemoglobin, MCV, mean corpuscular hemoglobin concentration (MCHC), serum creatinine, and liver disease. Mean Hb A 1c in MCH interdecile intervals fell from 6.8% (51 mmol/mol) in the lowest (≤27.5 pg) to 6.0% (43 mmol/mol) in the highest (>32.5 pg), with similar results for MCV. After adjustment for fasting glucose and other correlates of Hb A 1c , a 1 pg increase in MCH reduced the odds of Hb A 1c -defined dysglycemia, diabetes and poor glycemia control by 10%-14%. For at least 25% of patients, low or high MCH or MCV levels are associated with increased risk of an erroneous Hb A 1c -based identification of glycemia status. Although causality has not been demonstrated, these parameters should be taken into account in interpreting Hb A 1c levels in clinical practice. © 2016 American Association for Clinical Chemistry.

  11. Study of carbon black obtained by pyrolysis of waste scrap tyres

    Czech Academy of Sciences Publication Activity Database

    Mikulová, Z.; Šeděnková, Ivana; Matějová, Lenka; Večeř, M.; Dombek, V.

    2013-01-01

    Roč. 111, č. 2 (2013), s. 1475-1481 ISSN 1388-6150. [Central and Eastern European Conference on Thermal Analysis and Calorimetry /1./ - CEEC-TAC1. Craiova, 07.09.2011-10.09.2011] R&D Projects: GA ČR GA104/09/0972 Institutional research plan: CEZ:AV0Z40500505; CEZ:AV0Z40720504 Keywords : scrap tyres * carbon black * thermogravimetry Subject RIV: CI - Industrial Chemistry, Chemical Engineering Impact factor: 2.206, year: 2013

  12. 16 CFR 300.29 - Garments or products composed of or containing miscellaneous cloth scraps.

    Science.gov (United States)

    2010-01-01

    ... 16 Commercial Practices 1 2010-01-01 2010-01-01 false Garments or products composed of or containing miscellaneous cloth scraps. 300.29 Section 300.29 Commercial Practices FEDERAL TRADE COMMISSION... chiefly woolen fibers with the balance of undetermined mixtures of cotton, rayon or other non-woolen...

  13. Direct regeneration of recycled cathode material mixture from scrapped LiFePO4 batteries

    Science.gov (United States)

    Li, Xuelei; Zhang, Jin; Song, Dawei; Song, Jishun; Zhang, Lianqi

    2017-03-01

    A new green recycling process (named as direct regeneration process) of cathode material mixture from scrapped LiFePO4 batteries is designed for the first time. Through this direct regeneration process, high purity cathode material mixture (LiFePO4 + acetylene black), anode material mixture (graphite + acetylene black) and other by-products (shell, Al foil, Cu foil and electrolyte solvent, etc.) are recycled from scrapped LiFePO4 batteries with high yield. Subsequently, recycled cathode material mixture without acid leaching is further directly regenerated with Li2CO3. Direct regeneration procedure of recycled cathode material mixture from 600 to 800 °C is investigated in detail. Cathode material mixture regenerated at 650 °C display excellent physical, chemical and electrochemical performances, which meet the reuse requirement for middle-end Li-ion batteries. The results indicate the green direct regeneration process with low-cost and high added-value is feasible.

  14. HbA1c for diagnosis and prognosis of gestational diabetes mellitus.

    Science.gov (United States)

    Kwon, Soon Sung; Kwon, Ja-Young; Park, Yong-Won; Kim, Young-Han; Lim, Jong-Baeck

    2015-10-01

    HbA1c is a widely used marker in diagnosing type 2 diabetes mellitus (DM), but its clinical utility in diagnosing gestational diabetes mellitus (GDM) is not established. Here, we evaluated the clinical usefulness of HbA1c in diagnosing GDM and predicting the risk of future type 2 DM development among GDM patients. This retrospective, cross-sectional study included 321 subjects who underwent 100-g oral glucose tolerance tests (OGTT) during pregnancy. HbA1c and other variables were analyzed to evaluate their diagnostic performance for GDM. To evaluate the clinical usefulness of HbA1c in predicting future type 2 DM development, we classified GDM subjects who had more than 3 months of follow-up data into two subgroups: those who developed postpartum type 2 DM (PDM) and those who did not. HbA1c was significantly higher in the GDM group than in the normal control group. With the 100-g OGTT as reference, HbA1c showed 91.3% sensitivity and 62% specificity at a cut-off value of 5.05% (32 mmol/mol) for GDM diagnosis. At a cut-off value of 5.25% (34 mmol/mol), sensitivity was 73.6% and specificity was 77.2%. HbA1c levels during pregnancy were higher in those with PDM than in those without PDM (5.91 [41 mmol/mol] vs. 5.44% [36 mmol/mol], p<0.001). The prognostic value of HbA1c for PDM was evaluated by ROC curve analysis, with sensitivity of 78.6% and specificity of 72.5% at a cut-off value of 5.55% (37 mmol/mol). HbA1c showed high sensitivity with relatively low specificity for diagnosis of GDM in pregnant women and was a potential predictor of PDM. HbA1c may be able to be used as a simple and less invasive alternative screening test for OGTT in GDM patients. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

  15. Thermolysis of scrap tire and rubber in sub/super-critical water.

    Science.gov (United States)

    Li, Qinghai; Li, Fuxin; Meng, Aihong; Tan, Zhongchao; Zhang, Yanguo

    2018-01-01

    The rapid growth of waste tires has become a serious environmental issue. Energy and material recovery is regarded as a promising use for waste tires. Thermolysis of scrap tire (ST), natural rubber (NR), and styrene-butadiene rubber (SBR) was carried out in subcritical and supercritical water using a temperature-pressure independent adjustable batch tubular reactor. As a result, oil yields increased as temperature and pressure increased, and they reached maximum values as the state of water was near the critical point. However, further increases in water temperature and pressure reduced the oil yields. The maximum oil yield of 21.21% was obtained at 420 °C and 18 MPa with a reaction time of 40 min. The relative molecular weights of the chemicals in the oil products were in the range of 70-140 g/mole. The oil produced from ST, NR, and SBR contained similar chemical compounds, but the oil yield of SR was between those of NR and SBR. The oil yield from thermolysis of subcritical or supercritical water should be further improved. The main gaseous products, including CH 4 , C 2 H 2 , C 2 H 4 , C 2 H 6 , and C 3 H 8 , increased with reaction time, temperature, and pressure, whereas the solid residues, including carbon black and impurities, decreased. These results provide useful information to develop a sub/super-critical water thermolysis process for energy and material regeneration from waste tires. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. EPA and GSA Webinar: E Scrap Management, Computers for Learning and the Federal Green Challenge

    Science.gov (United States)

    EPA and the General Services Administration (GSA) are hosting a webinar on May 2, 2018. Topics will include policies and procedures on E Scrap management, a review of the Computers For Leaning Program, and benefits of joining the Federal Green Challenge.

  17. Evaluation of the DCA Vantage analyzer for HbA 1c assay.

    Science.gov (United States)

    Szymezak, Jean; Leroy, Nathalie; Lavalard, Emmanuelle; Gillery, Philippe

    2008-01-01

    Measurement of HbA 1c is key in monitoring diabetic patients in both laboratories and clinical units, where HbA 1c results are used as part of patient education. We have evaluated the DCA Vantage, a new device for immunological assay of HbA 1c. HbA 1c results obtained were evaluated in terms of precision, linearity, specificity and practicability, and were compared with results obtained by a Variant II HPLC method. The method exhibited intra- and inter-assay coefficients of variation lower than 2.6% and 4.0%, respectively, and good correlation with the comparison HPLC method (r2=0.9776). No interference was noted in the presence of labile HbA 1c or carbamylated hemoglobin. The new device exhibited improved practicability characteristics and allowed better sample identification, better management of quality control routines and greater connectivity possibilities compared to the previous DCA 2000 analyzer. This new analyzer exhibited analytical and practical characteristics very suitable for HbA 1c assay for laboratory or point-of-care use according to good laboratory practice.

  18. Traditional risk factors as determinants of heart rate recovery in patients with diabetes mellitus type 2 without known coronary artery disease

    Science.gov (United States)

    Silaban, Sanny; Afif Siregar, A.; Hasan, H.; Aryfa Andra, C.

    2018-03-01

    The impact of Traditional risk factors on heart rate recovery (HRR) has not been studied in patients Diabetes Mellitus type 2 without known coronary artery disease (CAD). For this reason, we sought to determine the association between HRR as cardiac autonomic dysfunction marker and traditonal risk factors. The study was conducted with a cross-sectional study involving 89 patients with Type 2 Diabetes Mellitus without known having coronary artery disease. The data was taken through anamnese and laboratory tests, and subjects who met the criteria were tested for a treadmill exercise to assess heart rate recovery in the first minute. In bivariate analysis Dyslipidemia, Hypertension, smoker, age, duration of DM≥ 5 years, HbA1C ≥7.5, Peak Heart rate, functional capacity and ST depression ischemic have an association with heart rate recovery. In multivariate analysis patients with hyper triglyceride, smoker, overweight, duration of diabetes ≥ five years and HbA1C ≥ 7,5 have lower heart rate recovery significantly. Traditional risk factors are determinant factors for heart rate recovery in patients with Diabetes Mellitus type 2 without known coronary artery disease.

  19. Analysis of HbA1c on an automated multicapillary zone electrophoresis system.

    Science.gov (United States)

    Rollborn, Niclas; Åkerfeldt, Torbjörn; Nordin, Gunnar; Xu, Xiao Yan; Mandic-Havelka, Aleksandra; Hansson, Lars-Olof; Larsson, Anders

    2017-02-01

    Hemoglobin A1c (HbA1c) is a frequently requested laboratory test and there is thus a need for high throughput instruments for this assay. We evaluated a new automated multicapillary zone electrophoresis instrument (Capillarys 3 Tera, Sebia, Lisses, France) for analysis of HbA1c in venous samples. Routine requested HbA1c samples were analyzed immunologically on a Roche c6000 instrument (n = 142) and then with the Capillarys 3 Tera instrument. The Capillarys 3 Tera instrument performed approximately 70 HbA1c tests/hour. There was a strong linear correlation between Capillarys 3 Tera and Roche Tina-Quant HbA1c Gen 3 assay (y = 1.003x - 0.3246 R 2  = .996). The total CV for the 12 capillaries varied between 0.8 and 2.2% and there was a good agreement between duplicate samples (R 2  = .997). In conclusion, the Capillarys 3 Tera instrument has a high assay capacity for HbA1c. It has a good precision and agreement with the Roche Tina-Quant HbA1c method and is well suited for high volume testing of HbA1c.

  20. Dynamics of α-Hb chain binding to its chaperone AHSP depends on heme coordination and redox state.

    Science.gov (United States)

    Kiger, Laurent; Vasseur, Corinne; Domingues-Hamdi, Elisa; Truan, Gilles; Marden, Michael C; Baudin-Creuza, Véronique

    2014-01-01

    AHSP is an erythroid molecular chaperone of the α-hemoglobin chains (α-Hb). Upon AHSP binding, native ferric α-Hb undergoes an unprecedented structural rearrangement at the heme site giving rise to a 6th coordination bond with His(E7). Recombinant AHSP, WT α-Hb:AHSP and α-Hb(HE7Q):AHSP complexes were expressed in Escherichia coli. Thermal denaturation curves were measured by circular dichroism for the isolated α-Hb and bound to AHSP. Kinetics of ligand binding and redox reactions of α-Hb bound to AHSP as well as α-Hb release from the α-Hb:AHSP complex were measured by time-resolved absorption spectroscopy. AHSP binding to α-Hb is kinetically controlled to prevail over direct binding with β-chains and is also thermodynamically controlled by the α-Hb redox state and not the liganded state of the ferrous α-Hb. The dramatic instability of isolated ferric α-Hb is greatly decreased upon AHSP binding. Removing the bis-histidyl hexacoordination in α-HbH58(E7)Q:AHSP complex reduces the stabilizing effect of AHSP binding. Once the ferric α-Hb is bound to AHSP, the globin can be more easily reduced by several chemical and enzymatic systems compared to α-Hb within the Hb-tetramer. α-Hb reduction could trigger its release from AHSP toward its final Hb β-chain partner producing functional ferrous Hb-tetramers. This work indicates a preferred kinetic pathway for Hb-synthesis. The cellular redox balance in Hb-synthesis should be considered as important as the relative proportional synthesis of both Hb-subunits and their heme cofactor. The in vivo role of AHSP is discussed in the context of the molecular disorders observed in thalassemia. © 2013 Elsevier B.V. All rights reserved.

  1. Treatment of Ni-EDTA containing wastewater by electrocoagulation using iron scraps packed-bed anode.

    Science.gov (United States)

    Ye, Xiaokun; Zhang, Junya; Zhang, Yan; Lv, Yuancai; Dou, Rongni; Wen, Shulong; Li, Lianghao; Chen, Yuancai; Hu, YongYou

    2016-12-01

    The unique electrocoagulator proposed in this study is highly efficient at removing Ni-EDTA, providing a potential remediation option for wastewater containing lower concentrations of Ni-EDTA (Ni ≤ 10 mg L -1 ). In the electrocoagulation (EC) system, cylindrical graphite was used as a cathode, and a packed-bed formed from iron scraps was used as an anode. The results showed that the removal of Ni-EDTA increased with the application of current and favoured acidic conditions. We also found that the iron scrap packed-bed anode was superior in its treatment ability and specific energy consumption (SECS) compared with the iron rod anode. In addition, the packed density and temperature had a large influence on the energy consumption (ECS). Over 94.3% of Ni and 95.8% of TOC were removed when conducting the EC treatment at an applied current of 0.5 A, initial pH of 3, air-purged rate 0.2 L min -1 , anode packed density of 400 kg m -3 temperature of 313 K and time of 30 min. SEM analysis of the iron scraps indicated that the specific area of the anode increased after the EC. The XRD analysis of flocs produced during EC revealed that hematite (α-Fe 2 O 3 ) and magnetite (Fe 3 O 4 ) were the main by-products under aerobic and anoxic conditions, respectively. A kinetic study demonstrated that the removal of Ni-EDTA followed a first-order model with the current parameters. Moreover, the removal efficiency of real wastewater was essentially consistent with that of synthetic wastewater. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Assessment of dose level of ionizing radiation in army scrap

    International Nuclear Information System (INIS)

    Abdel Hamid, S. M.

    2010-12-01

    Radiation protection is the science of protecting people and the environment from the harmful effects of ionizing radiation, which includes both particle radiation and high energy radiation. Ionizing radiation is widely used in industry and medicine. Any human activity of nuclear technologies should be linked to the foundation of scientific methodology and baseline radiation culture to avoid risk of radiation and should be working with radioactive materials and expertise to understand, control practices in order to avoid risks that could cause harm to human and environment. The study was conducted in warehouses and building of Sudan air force Khartoum basic air force during September 2010. The goal of this study to estimate the radiation dose and measurement of radioactive contamination of aircraft scrap equipment and increase the culture of radiological safety as well as the concept of radiation protection. The results showed that there is no pollution observed in the contents of the aircraft and the spire part stores outside, levels of radiation dose for the all contents of the aircraft and spire part within the excitable level, except temperature sensors estimated radiation dose about 43 μSv/h outside of the shielding and 12 μSv/h inside the shielding that exceeded the internationally recommended dose level. One of the most important of the identification of eighteen (18) radiation sources used in temperature and fuel level sensors. These are separated from the scrap, collected and stored in safe place. (Author)

  3. The isolation of the γ subunit of fetal hemoglobin (HbF) and its use in a radioimmunoassay for HbF

    International Nuclear Information System (INIS)

    James, R.F.L.; Shuster, J.; Freedman, S.O.; Gold, P.

    1980-01-01

    A method is described for the purification, from fetal hemoglobin (HbF), of the fetal specific globin chain (γ chain) in its native state. In the absence of α chain (the globin chain common to all adult human hemoglobins) γ chain, when used as an immunogen, is able to express its unique antigenicity. Here, a specific, high titer antiserum raised against γ chain has been used to establish a sensitive radioimmunoassay for HbF. This approach may be applicable to the measurement of other normal and abnormal hemoglobins. (Auth.)

  4. Hb A2 Episkopi - a novel δ-globin chain variant [HBD:c.428C>T] in a family of mixed Cypriot-Lebanese descent.

    Science.gov (United States)

    Lederer, Carsten W; Pavlou, Eleni; Tanteles, George A; Evangelidou, Paola; Sismani, Carolina; Kolnagou, Annita; Sitarou, Maria; Christou, Soteroulla; Hadjigavriel, Michael; Kleanthous, Marina

    2017-06-01

    Thalassaemia is a potentially lethal inherited anaemia, caused by reduced or absent synthesis of globin chains. Measurement of the minor adult haemoglobin Hb A 2 , combining α- with δ-globin, is critical for the routine diagnosis of carrier status for α- or β-thalassaemia. Here, we aim to characterize a novel δ-globin variant, Hb A 2 Episkopi, in a single family of mixed Lebanese and Cypriot ancestry with mild hypochromic anaemia and otherwise normal globin genotype, which also presents with a coincidental 0.78-Mb sequence duplication on chromosome 1 (1q44) and developmental abnormalities. Analyses included comprehensive haematological analyses, cation-exchange high-performance liquid chromatography (CE-HPLC), cellulose acetate electrophoresis (CAE), Sanger sequencing and structure-based stability predictions for Hb A 2 Episkopi. The GCT > GTT missense mutation, underlying Hb A 2 Episkopi, HBD:c.428C > T, introduces a cd142 codon change in the mature protein, resulting in reduced normal Hb A 2 amounts and a novel, less abundant Hb A 2 variant (HGVS: HBD:p.A143V), detectable as a delayed peak by CE-HPLC. The latter was in line with structure-based stability predictions, which indicated that the substitution of a marginal, non-helical and non-interface residue, five amino acids from the δ-globin chain carboxy-terminus, was moderately destabilizing. Detection of the new variant depends on the diagnostic set-up and had failed by CAE and on an independent CE-HPLC system, which, in unfavourable circumstances, may lead to misdiagnoses of β-thalassaemia as α-thalassaemia. Given the mixed background of the affected family, the ethnic origin of the mutation is unclear, and this study thus suggests awareness for possible detection of Hb A 2 Episkopi in both the Cypriot and the Lebanese populations.

  5. Legislative and Regulatory Control for the Safety of Radioactively Contaminated Scrap Metals Generated from Mining and Mineral Processing Facilities in South Africa

    Energy Technology Data Exchange (ETDEWEB)

    Mohajane, E. P.; Shale, K., E-mail: PEMohajane@nnr.co.za [National Nuclear Regulator, Centurion, Gauteng (South Africa)

    2011-07-15

    In South Africa, enhanced levels of naturally occurring radioactive materials (NORM) are associated with many mining and industrial processes. Significant amounts of waste materials are involved which can result in radiation exposure of the workers and the public particularly through the diversion of materials into the public domain. The following operations have been regulated in South Africa for the past twenty years: operating metallurgical plants utilizing NORM, underground mining operations, scrap recyclers and smelters, and rehabilitation and remediation activities involving the above sites. The radioactively contaminated scrap metal generated from the above mentioned facilities is available for recycling in amounts of thousands of tons. The South African government has, to a certain extent, responded to the above-mentioned challenges by introducing regulatory controls to the affected industries. The existing regulatory controls have, however, not provided absolute answers to all issues associated with the management of scrap. (author)

  6. USING THE SCRAP TIRES TO PRODUCE A FLEXIBLE COUPLER

    Directory of Open Access Journals (Sweden)

    Tahsean A. Hussain

    2018-01-01

    Full Text Available The scrap tires considered a problematic source of waste, the old rubber tires causes a big environmental problem that is need much money and effort to disposes it safely. In Iraq there are more than two million used tires disposed to the environment annually. one of the tire’s recycling methods is the use of tire layers to produce a new rubber parts used in the engineering and industrial purposes as the bridges and machines dampers, this trend of recycling doesn’t take a sufficient care comparing with the other uses. There are a lot of studies conducted in these field, these studies suggests many methods to manage the huge number of scrap tires, the current paper aims to use the old rubber tires in engineering purposes (especially as a coupler joins the motor or engines with the other equipment as electric dynamo or pumps, the study focusing on the mechanical properties of a strip from a used tires and comparing with one prepared in the lab., and suggesting a new method to use as an engineering parts (for example the coupler lays between the IC engine and the dynamo of an electric generator. One of the results obtained from the experiments, there is no significant difference between the mechanical properties of the old and the new strip, (in the tensile test, the breaking force of the -Lab. tensile specimen- is 137 N whereas the specimen of old tire have a breaking force 113.27 N, but they are same in the elongation. A computational example is suggested to estimate the dimensions of a flexible coupler use an old tire pieces.

  7. Hb A1c Separation by High Performance Liquid Chromatography in Hemoglobinopathies

    Directory of Open Access Journals (Sweden)

    Vani Chandrashekar

    2016-01-01

    Full Text Available Hb A1c measurement is subject to interference by hemoglobin traits and this is dependent on the method used for determination. In this paper we studied the difference between Hb A1c measured by HPLC in hemoglobin traits and normal chromatograms. We also studied the correlation of Hb A1c with age. Hemoglobin analysis was carried out by high performance liquid chromatography. Spearman’s rank correlation was used to study correlation between A1c levels and age. Mann-Whitney U test was used to study the difference in Hb A1c between patients with normal hemoglobin and hemoglobin traits. A total of 431 patients were studied. There was positive correlation with age in patients with normal chromatograms only. No correlation was seen in Hb E trait or beta thalassemia trait. No significant difference in Hb A1c of patients with normal chromatograms and patients with hemoglobin traits was seen. There is no interference by abnormal hemoglobin in the detection of A1c by high performance liquid chromatography. This method cannot be used for detection of A1c in compound heterozygous and homozygous disorders.

  8. HB+ prepares for insertion into the CMS solenoid

    CERN Multimedia

    Dave Barney, CERN

    2006-01-01

    With calibration of the first half of the barrel Hadron Calorimeter (HB+) complete (using a radioactive source), preparations begin for its insertion into the solenoid for the Magnet Test and Cosmic Challenge (MTCC). It was moved out of its alcove at the beginning of March - a non-trivial (but completely successful) operation due to the proximity of one of the barrel yoke rings (YB+1). The other half of the barrel Hadron Calorimeter (HB-) and one of the endcaps (HE+) should also be calibrated before the MTCC.

  9. Economic feasibility of radioactive scrap steel recycling

    International Nuclear Information System (INIS)

    Nichols, F.; Balhiser, R.; Rosholt, D.

    1995-01-01

    In the past, government and commercial nuclear operators treated radioactive scrap steel (RSS) as a liability and disposed of it by burial; this was an accepted and economical solution at that time. Today, environmental concerns about burial are changing the waste disposal picture by (a) causing burial costs to soar rapidly, (b) creating pressure to close existing burial sites, and (c) making it difficult and expensive to open and operate burial facilities. To exacerbate the problem, planned dismantling of nuclear facilities will substantially increase volumes of RSS open-quotes wasteclose quotes over the next 30 yr. This report describes a project with the intention of integrating the current commercial mini-mill approach of recycling uncontaminated steel with radiological controls to design a system that can process contaminated metals at prices significantly below the current processors or burial costs

  10. HB+ inserted into the CMS Solenoid

    CERN Multimedia

    Tejinder S. Virdee, CERN

    2006-01-01

    The first half of the barrel hadron calorimeter (HB+) has been inserted into the superconducting solenoid of CMS, in preparation for the magnet test and cosmic challenge. The operation went smoothly, lasting a couple of days.

  11. Spark Plasma Sintering As a Solid-State Recycling Technique: The Case of Aluminum Alloy Scrap Consolidation

    Directory of Open Access Journals (Sweden)

    Dimos Paraskevas

    2014-08-01

    Full Text Available Recently, “meltless” recycling techniques have been presented for the light metals category, targeting both energy and material savings by bypassing the final recycling step of remelting. In this context, the use of spark plasma sintering (SPS is proposed in this paper as a novel solid-state recycling technique. The objective is two-fold: (I to prove the technical feasibility of this approach; and (II to characterize the recycled samples. Aluminum (Al alloy scrap was selected to demonstrate the SPS effectiveness in producing fully-dense samples. For this purpose, Al alloy scrap in the form of machining chips was cold pre-compacted and sintered bellow the solidus temperature at 490 °C, under elevated pressure of 200 MPa. The dynamic scrap compaction, combined with electric current-based joule heating, achieved partial fracture of the stable surface oxides, desorption of the entrapped gases and activated the metallic surfaces, resulting in efficient solid-state chip welding eliminating residual porosity. The microhardness, the texture, the mechanical properties, the microstructure and the density of the recycled specimens have been investigated. An X-ray computed tomography (CT analysis confirmed the density measurements, revealing a void-less bulk material with homogeneously distributed intermetallic compounds and oxides. The oxide content of the chips incorporated within the recycled material slightly increases its elastic properties. Finally, a thermal distribution simulation of the process in different segments illustrates the improved energy efficiency of this approach.

  12. Serum levels of antioxidant vitamins in foetal haemoglobin (HbF ...

    African Journals Online (AJOL)

    Background: sickle cell anaemia (SCA) is one of the commonest health problems of Nigerian children. Method: The serum levels of antioxidant vitamins A (retinol), C (ascorbic acid) and E (alpha-tocopherol) were determined in foetal haemogbobin persistent sickle cell anaemic (Hb SS + F), sickle cell anaemic (Hb SS) and ...

  13. α-Thalassemia Associated with Hb Instability: A Tale of Two Features. The Case of Hb Rogliano or α1 Cod 108(G15)Thr→Asn and Hb Policoro or α2 Cod 124(H7)Ser→Pro.

    Science.gov (United States)

    Musollino, Gennaro; Cardiero, Giovanna; Flagiello, Angela; La Porta, Gaetana; Lagona, Laura; Prezioso, Romeo; Qualtieri, Gabriele; Gaudiano, Carlo; Medulla, Emilia; Merlino, Antonello; Pucci, Piero; Lacerra, Giuseppina

    2015-01-01

    We identified two new variants in the third exon of the α-globin gene in families from southern Italy: the Hb Rogliano, α1 cod108 ACC>AAC or α1[α108(G15)Thr→Asn] and the Hb Policoro, α2 cod124 TCC>CCC or α2[α124(H7)Ser→Pro]. The carriers showed mild α-thalassemia phenotype and abnormal hemoglobin stability features. These mutations occurred in the G and H helices of the α-globin both involved in the specific recognition of AHSP and β1 chain. Molecular characterization of mRNA, globin chain analyses and molecular modelling studies were carried out to highlight the mechanisms causing the α-thalassemia phenotype. The results demonstrated that the α-thalassemia defect associated with the two Hb variants originated by different defects. Hb Rogliano showed an intrinsic instability of the tetramer due to anomalous intra- and inter-chain interactions suggesting that the variant chain is normally synthesized and complexed with AHSP but rapidly degraded because it is unable to form the α1β1 dimers. On the contrary in the case of Hb Policoro two different molecular mechanisms were shown: the reduction of the variant mRNA level by an unclear mechanism and the protein instability due to impairment of AHSP interaction. These data highlighted that multiple approaches, including mRNA quantification, are needed to properly identify the mechanisms leading to the α-thalassemia defect. Elucidation of the specific mechanism leads to the definition of a given phenotype providing important guidance for the diagnosis of unstable variants. PMID:25730315

  14. Prevalence and predictors of the sub-target Hb level in children on dialysis

    DEFF Research Database (Denmark)

    van Stralen, Karlijn J; Krischock, Leah; Schaefer, Franz

    2012-01-01

    Anaemia is a common and potentially treatable co-morbidity of end-stage renal disease. We aimed to determine the prevalence of the sub-target haemoglobin (Hb) level among European children on dialysis and to identify factors associated with a low Hb level.......Anaemia is a common and potentially treatable co-morbidity of end-stage renal disease. We aimed to determine the prevalence of the sub-target haemoglobin (Hb) level among European children on dialysis and to identify factors associated with a low Hb level....

  15. A Family with γ-Thalassemia and High Hb A2 Levels.

    Science.gov (United States)

    Parmeggiani, Giulia; Gualandi, Francesca; Selvatici, Rita; Rimessi, Paola; Bigoni, Stefania; Taddei Masieri, Marina; Dolcini, Bernadetta; Venturoli, Anna; Cappabianca, Maria P; Ferlini, Alessandra; Ravani, Anna

    2016-06-01

    We describe a family carrying a γ-globin gene deletion associated with an increase of Hb A2 level beyond the normal range. The family included the proband, his sister and their father, all with increased Hb A2 and normal Hb F levels. The proband and his sister showed borderline values of mean corpuscular volume (MCV) and reduced values of mean corpuscular hemoglobin (Hb) (MCH). The proband was referred to our Medical Genetics Service for preconception counseling together with his partner, a typical β-thalassemia (β-thal) carrier. The results were negative for the most frequent α-thalassemia (α-thal) mutations, and had no significant sequence variations of the coding sequences and promoter of the β- and δ-globin genes. Quantitative analysis by multiplex ligation-dependent probe amplification (MPLA) of the β-globin gene cluster detected a heterozygous deletion, ranging between 2.1 and 4.7 kb, in the proband, his sister and the father. The deletion involved the (G)γ gene and (G)γ-(A)γ intergenic region, whereas the 3' region of the (A)γ gene was preserved. A subsequent gap-polymerase chain reaction (gap-PCR) showed that a hybrid (GA)γ fusion gene was present. The deletion segregated with the elevation of Hb A2. The MLPA analysis of the β-globin gene cluster in 150 control alleles excluded a common polymorphism. Despite stronger evidence being needed, the described family suggests a possible role of this γ-globin gene deletion in contributing to Hb A2 elevation, possibly by altering the transcription regulation of the cluster. We propose γ-globin gene dosage analysis to be performed in patients with unexplained elevated Hb A2 levels.

  16. HbA1c levels in individuals heterozygous for hemoglobin variants.

    Science.gov (United States)

    Tavares, Ricardo Silva; Souza, Fábio Oliveira de; Francescantonio, Isabel Cristina Carvalho Medeiros; Soares, Weslley Carvalho; Mesquita, Mauro Meira

    2017-04-01

    To evaluate the levels of glycated hemoglobin (HbA1c) in patients heterozygous for hemoglobin variants and compare the results of this test with those of a control group. This was an experimental study based on the comparison of HbA1c tests in two different populations, with a test group represented by individuals heterozygous for hemoglobin variants (AS and AC) and a control group consisting of people with electrophoretic profile AA. The two populations were required to meet the following inclusion criteria: Normal levels of fasting glucose, hemoglobin, urea and triglycerides, bilirubin > 20 mg/dL and non-use of acetylsalicylic acid. 50 heterozygous subjects and 50 controls were evaluated between August 2013 and May 2014. The comparison of HbA1c levels between heterozygous individuals and control subjects was performed based on standard deviation, mean and G-Test. The study assessed a test group and a control group, both with 39 adults and 11 children. The mean among heterozygous adults for HbA1c was 5.0%, while the control group showed a rate of 5.74%. Heterozygous children presented mean HbA1c at 5.11%, while the controls were at 5.78%. G-Test yielded p=0.93 for children and p=0.89 for adults. Our study evaluated HbA1c using ion exchange chromatography resins, and the patients heterozygous for hemoglobin variants showed no significant difference from the control group.

  17. HbA1c measurements from dried blood spots : validation and patient satisfaction

    NARCIS (Netherlands)

    Fokkema, Margaretha; Bakker, Andries J; de Boer, Fokje; Kooistra, Jeltsje; de Vries, Sifra; Wolthuis, Albert

    2009-01-01

    Background: This study evaluates HbA1c measurements from dried blood spots collected on filter paper and compares HbA1c from filter paper (capillary blood) with HbA1c measured in venous blood. Methods: Patient satisfaction was evaluated using a questionnaire. The performance with the filter paper

  18. Hb Presbyterian (HBB: c.327C>G) in a Nicaraguan Family.

    Science.gov (United States)

    Pernudy-Ubau, Allan; Salinas-Molina, Jaslyn; Requenez, Yaneris; Ortiz-Lopez, Marianela; Puller, Ann-Christin; García-Rosales, Kenia; Rodríguez-Estrada, Anaishelle; Rodríguez-Romero, Walter; Mejía-Baltodano, Gerardo; Luo, Hong-Yuan; Chui, David H K

    2017-01-01

    Hemoglobin (Hb) is the protein responsible for oxygen transportation. It is a tetrameric protein comprising two α- and two β-globin subunits. In the literature, a large number of mutations in the α- and β-globin genes have been documented. Among these mutations, Hb Presbyterian (HBB: c.327 C>G), is a naturally occurring mutant exerting low oxygen affinity. The C to G exchange (AAC>AAG) at codon 108 of the β-globin gene results in the substitution of asparagine by lysine. Here, we document the identification of HBB: c.327 C>G in a 6-year-old female patient and her father from Nicaragua and Cuba, respectively. The presence of the abnormal Hb was confirmed by cellulose acetate electrophoresis, high performance liquid chromatography (HPLC) and genomic DNA sequencing. The β-globin gene sequences for both, father and daughter, disclosed the heterozygous mutation at codon 108 to be Hb Presbyterian or HBB: c.327 C>G. The mutant Hb was previously reported in four families from North America, Germany, Japan and Spain, respectively. This is the fifth family carrying HBB: c.327 C>G described to date and the first report from Latin America.

  19. Evaluation of the costs and benefits of recycling radioactively contaminated scrap metal

    International Nuclear Information System (INIS)

    Durman, E.C.; Tsirigotis, P.; MacKinney, J.A.

    1995-01-01

    The U.S. Environmental Protection Agency (EPA) is evaluating the economic and technical issues associated with the potential recycling of radioactive scrap metals (RSM). These metals, usually only slightly contaminated, originate primarily from the decommissioning and decontamination (D and D) of federal facilities, licensees of the Nuclear Regulatory Commission, and certain unlicensed industries. EPA conducted a study entitled Analysis of the Potential Recycling of Department of Energy Radioactive Scrap Metal, September 6, 1994, for the U.S. Department of Energy (DOE) to provide information and tools to DOE for assessing DOE's problem with RSM from the D and D of their sites. EPA is now initiating an evaluation of RSM recycling to support a recycling regulation. Although the study prepared for DOE will provide a useful start for the regulatory analysis, additional information must be gathered to analyze the impacts of a recycling regulation that will apply to all potential generators of RSM. This paper summarizes cost-benefit issues related to an RSM recycling regulatory analysis, including: the quantity of potentially recyclable contaminated metals; costs of disposal at federal and private waste repositories; all potential environmental, health, and safety, and market impacts; and the potential for adverse effects on radio-sensitive industries. (author)

  20. Two α1-Globin Gene Point Mutations Causing Severe Hb H Disease.

    Science.gov (United States)

    Jiang, Hua; Huang, Lv-Yin; Zhen, Li; Jiang, Fan; Li, Dong-Zhi

    Hb H disease is generally a moderate form of α-thalassemia (α-thal) that rarely requires regular blood transfusions. In this study, two Chinese families with members carrying transfusion-dependent Hb H disease were investigated for rare mutations on the α-globin genes (HBA1, HBA2). In one family, Hb Zürich-Albisrieden [α59(E8)Gly→Arg; HBA1: c.178G>C] in combination with the Southeast Asian (- - SEA ) deletion was the defect responsible for the severe phenotype. In another family, a novel hemoglobin (Hb) variant named Hb Sichuan (HBA1: c.393_394insT), causes α-thal and a severe phenotype when associated with the - - SEA deletion. As these two HBA1 mutations can present as continuous blood transfusion-dependent α-thal, it is important to take this point into account for detecting the carriers, especially in couples in which one partner is already a known α 0 -thal carrier.

  1. On-line diagnosis and recovery of adversary attack using logic flowgraph methodology simulation

    International Nuclear Information System (INIS)

    Guarro, S.B.

    1986-01-01

    The Logic Flowgraph Methodology (LFM) allows the construction of special graph models for simulation of complex processes of causality, including feedback loops and sequential effects. Among the most notable features of LFM is the formal inclusion in its models of causality conditioning by logic switches imbedded in the modeled process, such as faults or modes of operation. The LFM model of a process is a graph structure that captures, in one synthetic representation, the relevant success and fault space characterization of that process. LFM is very similar to an artificial intelligence expert system shell. To illustrate the utilization of LFM, an application to the assessment and on-line monitoring of a material control facility is presented. The LFM models are used to model adversary action and control response, and to generate mini-diagnostic and recovery trees in real time, as well as reliability tress for off-line evaluation. Although the case study presented is for an imaginary facility, most of the conceptual elements that would be present in a real application have been retained in order to highlight the features and capabilities of the methodology

  2. Selective Extraction of Rare Earth Elements from Permanent Magnet Scraps with Membrane Solvent Extraction.

    Science.gov (United States)

    Kim, Daejin; Powell, Lawrence E; Delmau, Lætitia H; Peterson, Eric S; Herchenroeder, Jim; Bhave, Ramesh R

    2015-08-18

    The rare earth elements (REEs) such as neodymium, praseodymium, and dysprosium were successfully recovered from commercial NdFeB magnets and industrial scrap magnets via membrane assisted solvent extraction (MSX). A hollow fiber membrane system was evaluated to extract REEs in a single step with the feed and strip solutions circulating continuously through the MSX system. The effects of several experimental variables on REE extraction such as flow rate, concentration of REEs in the feed solution, membrane configuration, and composition of acids were investigated with the MSX system. A multimembrane module configuration with REEs dissolved in aqueous nitric acid solutions showed high selectivity for REE extraction with no coextraction of non-REEs, whereas the use of aqueous hydrochloric acid solution resulted in coextraction of non-REEs due to the formation of chloroanions of non-REEs. The REE oxides were recovered from the strip solution through precipitation, drying, and annealing steps. The resulting REE oxides were characterized with XRD, SEM-EDX, and ICP-OES, demonstrating that the membrane assisted solvent extraction is capable of selectively recovering pure REEs from the industrial scrap magnets.

  3. Submerged Glow-Discharge Plasma: An Economical Approach to Convert Construction Scrap Metal into Nanomaterials

    Science.gov (United States)

    Yek, Peter Nai Yuh; Rafiq Mirza Julaihi, Muhammad; Shahril Osman, Mohammad; Tiong, Tung Chuan; Lee, Wak Ha; Leing Lee, Chern

    2018-03-01

    Submerged glow-discharge plasma (SGDP) is relatively new among the various methods available for nanomaterials synthesis (NMs) techniques. This method allows great control over the production cost of nanomaterials synthesis. A lab-scale batch type SDGP technology has been constructed to produce nanomaterials and investigate the inter-relationship between plasma excitation voltages, electrodes submerged areas and electrolyte concentration. Metal oxide nanospheres has been synthesised from different electrolyte concentrations (1M-0.001M) and characterized by Scanning Electron Microscopy (SEM) and Energy Dispersive Spectroscopy (EDS). As the major results showed that the nanospheres are uniformly spherical with diameter size distribution are between 100 nm - 2μm. EDS analysis shown the nano-Iron Oxide have been formed. Scrap metal initially showed around 6.45% and 93.55% of Carbon and Iron composition respectively. After SGDP process to the scrap metal, Carbon content has increased to 34-35% and Iron content has reduced to around 15-40%. EDS results also shown the higher percentage of Iron amount has remained with lower electrolyte concentration and Current is proportionally related to submersion area of cathode.

  4. Correlation between Composition and Properties of Composite Material Based on Scrap Tires

    OpenAIRE

    Mālers, L; Plēsuma, R; Ločmele, L; Kalniņš, M

    2010-01-01

    Purpose of present work is to investigate mechanical and insulation properties of the composite material based on scrap tires and polyurethane-type binder in correlation with composition of composite material. The studies of material’s hardness must be considered as an express-method for estimation of the selected mechanical properties (E and ccompressive stress) of the composite material without direct experimental testing of given parameters. It was shown that composite material must be r...

  5. Ferrous and common nonferrous metals industries and associated scrap metals: a review

    International Nuclear Information System (INIS)

    Mautz, E.W.

    1975-11-01

    Literature on the common metals industries, scrap metal relationships, and transportation aspects has been reviewed as background information in a study to determine the feasibility of a portable melting facility for radioactively contaminated metals. This report draws substantially on government-sponsored studies. Aluminum, copper, iron and steel, and nickel metal industries are discussed from the viewpoints of the general industry characteristics, primary metal production processes, and secondary metal processing aspects. 46 references, 10 tables

  6. Diagnostic accuracy of HbA1c in diabetes between Eastern and Western.

    Science.gov (United States)

    Yan, Shuang; Liu, Siying; Zhao, Yashuang; Zhang, Wencui; Sun, Xiaohui; Li, Jianing; Jiang, Fuli; Ju, Jiaming; Lang, Ning; Zhang, Yingqi; Zhou, Weiyu; Li, Qiang

    2013-07-01

    In 2010, the American Diabetes Association recommended the use of HbA1c as a diagnostic criterion for diabetes. However, HbA1c is not an accepted diagnostic tool for diabetes in Eastern Asia, because genetic differences compromise the standardization of the diagnostic cut-off point. This study evaluated differences in the use of HbA1c for diagnosing diabetes in Eastern and Western populations and investigated whether HbA1c cut-off point of ≥ 6.5% is diagnostic of diabetes in patients from Eastern Asia. Literature was obtained from MEDLINE, EMBASE and Cochrane databases. The pooled sensitivity and specificity of each HbA1c cut-off point were extracted and compared between Western and Eastern populations. Differences in the cut-off point for diagnosing diabetes in each region were compared by examining differences in the area under summary receiver operating characteristic (SROC) curves. Twelve publications from Eastern countries (n = 59,735) and 13 from Western countries (n = 22,954) were included in the analysis. Areas under SROC curves in the Eastern and Western groups were 0.9331 and 0.9120, respectively (P = 0.98). The cut-off point of the highest Youden index was 6.0%. At the HbA1c cut-off point of 6.5%, the pooled sensitivity and specificity were 58.7% and 98.4% for Eastern countries and 65.5% and 98.1% for Western countries, respectively. HbA1c exhibits the same diagnostic value for diabetes in Eastern and Western populations. In both populations, HbA1c levels > 6.0% identify the population at high risk of diabetes, and HbA1c > 6.5% is diagnostic of clinically established diabetes. © 2013 Stichting European Society for Clinical Investigation Journal Foundation. Published by John Wiley & Sons Ltd.

  7. HB-EGF is necessary and sufficient for Müller glia dedifferentiation and retina regeneration

    Science.gov (United States)

    Wan, Jin; Ramachandran, Rajesh; Goldman, Daniel

    2011-01-01

    Summary Müller glia (MG) dedifferentiation into a cycling population of multipotent progenitors is crucial to zebrafish retina regeneration. The mechanisms underlying MG dedifferentiation are unknown. Here we report that heparin-binding epidermal-like growth factor (HB-EGF) is rapidly induced in MG residing at the injury site and that proHB-EGF ectodomain shedding is necessary for retina regeneration. Remarkably, HB-EGF stimulates the formation of multipotent MG-derived progenitors in the uninjured retina. We show that HB-EGF mediates its effects via an EGFR/MAPK signal transduction cascade that regulates the expression of regeneration-associated genes, like ascl1a and pax6b. We also uncover an HB-EGF/Ascl1a/Notch/hb-egfa signaling loop that helps define the zone of injury-responsive MG. Finally, we show that HB-EGF acts upstream of the Wnt/β-catenin signaling cascade that controls progenitor proliferation. These data provide a link between extracellular signaling and regeneration-associated gene expression in the injured retina and suggest strategies for stimulating retina regeneration in mammals. PMID:22340497

  8. Leaching of DOC, DN, and inorganic constituents from scrap tires.

    Science.gov (United States)

    Selbes, Meric; Yilmaz, Ozge; Khan, Abdul A; Karanfil, Tanju

    2015-11-01

    One concern for recycle and reuse of scrap tires is the leaching of tire constituents (organic and inorganic) with time, and their subsequent potential harmful impacts in environment. The main objective of this study was to examine the leaching of dissolved organic carbon (DOC), dissolved nitrogen (DN), and selected inorganic constituents from scrap tires. Different sizes of tire chips and crumb rubber were exposed to leaching solutions with pH's ranging from 3.0 to 10.0 for 28days. The leaching of DOC and DN were found to be higher for smaller size tire chips; however, the leaching of inorganic constituents was independent of the size. In general, basic pH conditions increased the leaching of DOC and DN, whereas acidic pH conditions led to elevated concentrations of metals. Leaching was minimal around the neutral pH values for all the monitored parameters. Analysis of the leaching rates showed that components associated with the rubbery portion of the tires (DOC, DN, zinc, calcium, magnesium, etc.) exhibited an initial rapid followed by a slow release. On the other hand, a constant rate of leaching was observed for iron and manganese, which are attributed to the metal wires present inside the tires. Although the total amounts that leached varied, the observed leaching rates were similar for all tire chip sizes and leaching solutions. Operation under neutral pH conditions, use of larger size tire chips, prewashing of tires, and removal of metal wires prior to application will reduce the impact of tire recycle and reuse. Copyright © 2015 Elsevier Ltd. All rights reserved.

  9. Some functional properties of composite material based on scrap tires

    Science.gov (United States)

    Plesuma, Renate; Malers, Laimonis

    2013-09-01

    The utilization of scrap tires still obtains a remarkable importance from the aspect of unloading the environment from non-degradable waste [1]. One of the most prospective ways for scrap tires reuse is a production of composite materials [2] This research must be considered as a continuation of previous investigations [3, 4]. It is devoted to the clarification of some functional properties, which are considered important for the view of practical applications, of the composite material. Some functional properties of the material were investigated, for instance, the compressive stress at different extent of deformation of sample (till 67% of initial thickness) (LVS EN 826) [5] and the resistance to UV radiation (modified method based on LVS EN 14836) [6]. Experiments were realized on the purposefully selected samples. The results were evaluated in the correlation with potential changes of Shore C hardness (Shore scale, ISO 7619-1, ISO 868) [7, 8]. The results showed noticeable resistance of the composite material against the mechanical influence and ultraviolet (UV) radiation. The correlation with the composition of the material, activity of binder, definite technological parameters, and the conditions supported during the production, were determined. It was estimated that selected properties and characteristics of the material are strongly dependent from the composition and technological parameters used in production of the composite material, and from the size of rubber crumb. Obtained results show possibility to attain desirable changes in the composite material properties by changing both the composition and technological parameters of examined material.

  10. Co-inheritance of the rare β hemoglobin variants Hb Yaounde, Hb Görwihl and Hb City of Hope with other alterations in globin genes: impact in genetic counseling.

    Science.gov (United States)

    Vinciguerra, Margherita; Passarello, Cristina; Leto, Filippo; Cassarà, Filippo; Cannata, Monica; Maggio, Aurelio; Giambona, Antonino

    2015-04-01

    Nearly 1183 different molecular defects of the globin genes leading to hemoglobin variants have been identified (http://globin.bx.psu.edu) over the past decades. The purpose of this study was to report three cases, never described in the literature, of co-inheritance of three β hemoglobin variants with other alterations in globin genes and to evaluate the clinical significance to conduct an appropriate genetic counseling. We report the molecular study performed in three probands and their families, sampling during the screening program conducted at the Laboratory for Molecular Prenatal Diagnosis of Hemoglobinopathies at Villa Sofia-Cervello Hospital in Palermo, Italy. This work allowed us to describe the co-inheritance of three rare β hemoglobin variants with other alterations in globin genes: the β hemoglobin variant Hb Yaounde [β134(H12)Val>Ala], found for the first time in combination with ααα(anti3.7) arrangement, and the β hemoglobin variants Hb Görwihl [β5(A2)Pro>Ala] and Hb City of Hope [β69(E13)Gly>Ser], found both in association with β(0) -thalassemia. The present work emphasizes the importance of a careful evaluation of the hematological data, especially in cases of atypical hematological parameters, to carry out an adequate and complete molecular study and to formulate an appropriate genetic counseling for couples at risk. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  11. Role of HbA1c in predicting risk for congenital malformations.

    Science.gov (United States)

    Hammouda, Sahar Ali Ibrahim; Hakeem, Rubina

    2015-12-01

    Association between conventionally identified hyperglycemias and rates of congenital abnormalities is known; however there is less information about role of HbA1c in determining gestational hyperglycemias and associated risks. This study tried to explore the association between HbA1c in women without known diabetes at first antenatal visit and risk of congenital malformations (CM) among Saudi women living at Al-Madinah Al-Monawarah. Eleven hundred and eighty (1180), healthy, first-trimester pregnant Saudi females without known diabetes, were selected from various antenatal care clinics of Al-Madinah Al-Monawarah city. General clinical and biochemical data was collected for this study by researchers at first visit and the time of delivery. Nearly one fifth (19.6%) of mothers had above normal HbA1c (>5.7) at first visit. Rates of CM had significant positive association with level of HbA1c. Rate of CM among those who had HbA1c in diabetes range, pre-diabetes range or normal range was 27.8%, 9.8% and 3.0%, respectively. The difference was significant between normal and pre-diabetes at the level P=0.000 and between pre-diabetes and diabetes at level P=0.038. In this study HbA1c is found to be a valuable predictor of risk of congenital malformations. This observation calls for further studies and establishment of policies for care of pregnant mothers having higher than normal HbA1c at first visit. Copyright © 2015 Primary Care Diabetes Europe. Published by Elsevier Ltd. All rights reserved.

  12. Baseline Report on HB2320

    Science.gov (United States)

    State Council of Higher Education for Virginia, 2015

    2015-01-01

    Staff provides this baseline report as a summary of its preliminary considerations and initial research in fulfillment of the requirements of HB2320 from the 2015 session of the General Assembly. Codified as § 23-7.4:7, this legislation compels the Education Secretary and the State Council of Higher Education for Virginia (SCHEV) Director, in…

  13. Evaluating awareness and practices pertaining to radioactive waste management among scrap dealers in Delhi, India.

    Science.gov (United States)

    Makkar, Nayani; Chandra, Tany; Agrawal, Prachi; Bansal, Harshit; Singh, Simranjeet; Anand, Tanu; Gupta, Mannan Kumar; Kumar, Rajesh

    2014-01-01

    With nuclear technology rapidly taking the spotlight in the last 50 years, radiation accidents seem to be a harsh reality of the modern world. The Mayapuri Radiation accident of 2010 was the worst radiation accident India has yet dealt with. Two years thereafter, we designed a study to assess the awareness and practices regarding radioactive waste among scrap dealers aiming to assess deficiencies in radiation disaster preparedness. A community based cross-sectional study. The study population consisted of 209 volunteers (from 108 scrap dealerships) including 108 shop-owners and 101 workers segregated as Group A consisting of 54 dealerships in Mayapuri and Group B of 54 dealerships from the rest of the city. Subjects were then interviewed using a semi-structured questionnaire. Awareness about radioactive waste varied significantly with level of education (p = 0.024), Kuppuswamy's socio-economic scale (p = 0.005), age of the scrap dealer (p = 0.049) and his work experience (p = 0.045). The larger dealerships in Mayapuri were more aware about radioactive waste (p = 0.0004), the accident in 2010 (p = 0.0002), the symbol for radiation hazard (p = 0.016), as well as the emergency guidelines and the agencies to contact in the event of a radiation accident. Our findings seem to signify that while governmental and non-governmental agencies were successful in implementing prompt disaster response and awareness programs, the community continues to be inadequately prepared. These go on to suggest that though concerted awareness and training programs do benefit the affected community, economic and social development is the key to disaster prevention and mitigation.

  14. HbQ-India associated with microcytosis: An uncommon hemoglobin variant associated with a common hematologic condition

    Directory of Open Access Journals (Sweden)

    Amit Kumar Yadav

    2010-09-01

    Full Text Available HbQ-India is a rare alpha chain variant that usually presents in the heterozygous state. Normally, HbQ-India is clinically silent. It becomes symptomatic when present in association with other conditions. We report a case of HbQ-India with concomitant presence of iron deficiency anemia. A 16-year-old female presented with weakness and pallor intermittently for six years. Complete blood count showed severe microcytic hypochromic anemia. Hemoglobin electrophoresis showed a prominent band in the S,D,G region. Tests for sickling were negative. High performance liquid chromatography (HPLC showed a peak in the unknown window (4.70-4.90 min suggestive of HbQ-India. Serum iron profile was suggestive of iron deficiency anemia. Based on the above findings, a diagnosis of coexistent HbQ-India–iron deficiency anemia was made. A family study revealed the father as having moderate anemia with similar findings while the mother was normal. Abnormal hemoglobin in the patient was confirmed by molecular diagnosis.HbQ variants are the alpha globin chain variants due to structural mutations (α64 Asp→His inherited in autosomal dominant fashion. Three molecular variant types have been documented, namely HbQ-India, HbQ-Thailand and HbQ-Iran. Normally, HbQ is clinically silent. Therefore, careful screening of the samples using routine techniques like Hb electrophoresis and HPLC are needed for identification of such abnormal hemoglobin variants like HbQ-India.

  15. 2,3-DPG-Hb complex: a hypothesis for an asymmetric binding.

    Science.gov (United States)

    Pomponi, M; Bertonati, C; Fuglei, E; Wiig, O; Derocher, A E

    2000-05-15

    This study was undertaken to test the symmetry of 2,3-diphosphoglycerate (2,3-DPG) binding site in hemoglobin (Hb). From Arnone's study [A. Arnone, Nature (London) 237 (1972) 146] the 2,3-DPG binding site is located at the top of the cavity, that runs through the center of the deoxy-Hb molecule. However, it is possible that this symmetry reported by Arnone, for crystals of 2,3-DPG-Hb complex, might not be conserved in solution. In this paper, we report the 31P nuclear magnetic resonances of the 2,3-DPG interaction with Hb. The 2,3-DPG chemical shifts of the P2 and P3 resonance are both pH- and hemoglobin-dependent [protein from man, polar bear (Ursus maritimus), Arctic fox (Alopex lagopus) and bovine]. 2,3-DPG binds tightly to deoxyhemoglobin and weakly, nevertheless significantly, to oxyhemoglobin. In particular, our results suggest similar spatial position of the binding site of 2,3-DPG in both forms of Hb in solutions. However, the most unexpected result was the apparent loss of symmetry in the binding site, which might correlate with the ability of the hemoglobin to modulate its functional behavior. The different interactions of the phosphate groups indicate small differences in the quaternary structure of the different deoxy forms of hemoglobin. Given the above structural perturbation an asymmetric binding in the complex could justify, at least in part, different physiological properties of Hb. Regardless, functionally relevant effects of 2,3-DPG seem to be measured and best elucidated through solution studies.

  16. Advanced technologies for decontamination and conversion of scrap metal

    International Nuclear Information System (INIS)

    Valerie MacNair; Steve Sarten; Thomas Muth; Brajendra Mishra

    1999-01-01

    The Department of Energy (DOE) faces the task of decommissioning much of the vast US weapons complex. One challenge of this effort includes the disposition of large amounts of radioactively contaminated scrap metal (RSM) including but not limited to steel, nickel, copper, and aluminum. The decontamination and recycling of RSM has become a key element in the DOE's strategy for cleanup of contaminated sites and facilities. Recycling helps to offset the cost of decommissioning and saves valuable space in the waste disposal facilities. It also reduces the amount of environmental effects associated with mining new metals. Work on this project is geared toward finding decontamination and/or recycling alternatives for the RSM contained in the decommissioned gaseous diffusion plants including approximately 40,000 tons of nickel. The nickel is contaminated with Technetium-99, and is difficult to remove using traditional decontamination technologies. The project, titled ''Advanced Technologies for Decontamination and Conversion of Scrap Metal'' was proposed as a four phase project. Phase 1 and 2 are complete and Phase 3 will complete May 31, 1999. Stainless steel made from contaminated nickel barrier was successfully produced in Phase 1. An economic evaluation was performed and a market study of potential products from the recycled metal was completed. Inducto-slag refining, after extensive testing, was eliminated as an alternative to remove technetium contamination from nickel. Phase 2 included successful lab scale and pilot scale demonstrations of electrorefining to separate technetium from nickel. This effort included a survey of available technologies to detect technetium in volumetrically contaminated metals. A new process to make sanitary drums from RSM was developed and implemented. Phase 3 included a full scale demonstration of electrorefining, an evaluation of electro-refining alternatives including direct dissolution, melting of nickel into anodes, a laser cutting

  17. Worker exposures from recycling surface contaminated radioactive scrap metal

    International Nuclear Information System (INIS)

    Kluk, A.; Phillips, J.W.; Culp, J.

    1996-01-01

    Current DOE policy permits release from DOE control of real property with residual levels of surficial radioactive contamination if the contamination is below approved guidelines. If the material contains contamination that is evenly distributed throughout its volume (referred to as volumetric contamination), then Departmental approval for release must be obtained in advance. Several DOE sites presently recycle surface contaminated metal, although the quantities are small relative to the quantities of metal processed by typical mini-mills, hence the potential radiation exposures to mill workers from processing DOE metals and the public from the processed metal are at present also a very small fraction of their potential value. The exposures calculated in this analysis are based on 100% of the scrap metal being processed at the maximum contamination levels and are therefore assumed to be maximum values and not likely to occur in actual practice. This paper examines the relationship between the surface contamination limits established under DOE Order 5400.5, open-quotes Radiation Protection of the Public and the Environment,close quotes and radiation exposures to workers involved in the scrap metal recycling process. The analysis is limited to surficial contamination at or below the guideline levels established in DOE Order 5400.5 at the time of release. Workers involved in the melting and subsequent fabrication of products are not considered radiation workers (no requirements for monitoring) and must be considered members of the public. The majority of the exposures calculated in this analysis range from tenths of a millirem per year (mrem/yr) to less than 5 mrem/yr. The incremental risk of cancer associated with these exposures ranges from 10 -8 cancers per year to 10 -6 cancers per year

  18. Line Width Recovery after Vectorization of Engineering Drawings

    Directory of Open Access Journals (Sweden)

    Gramblička Matúš

    2016-12-01

    Full Text Available Vectorization is the conversion process of a raster image representation into a vector representation. The contemporary commercial vectorization software applications do not provide sufficiently high quality outputs for such images as do mechanical engineering drawings. Line width preservation is one of the problems. There are applications which need to know the line width after vectorization because this line attribute carries the important semantic information for the next 3D model generation. This article describes the algorithm that is able to recover line width of individual lines in the vectorized engineering drawings. Two approaches are proposed, one examines the line width at three points, whereas the second uses a variable number of points depending on the line length. The algorithm is tested on real mechanical engineering drawings.

  19. Decontamination and decommissioning of the MTR-603 HB-2 cubicle

    International Nuclear Information System (INIS)

    Smith, D.L.

    1987-01-01

    The decontamination and decommissioning (D and D) of the MTR-603 HB-2 cubicle located at the Idaho National Engineering Laboratory (INEL) are described. The HP-2 cubicle became radioactively contaminated during out-of-pile circulating water loop experiments conducted in the Materials Testing Reactor in the 1950s and 1960s. The work performed to accomplish the D and D objectives of reducing the high radiation fields caused by contamination inside the cubicle, preventing future contamination spread, and making about 1400 ft 2 of floor space available for reuse are discussed. Decommissioning of the HB-2 cubicle consisted of total dismantlement of the cubicle and its contents and was performed without disrupting ongoing laboratory work being conducted in areas surrounding the HB-2 cubicle

  20. Hb H disease resulting from the association of an αº-thalassemia allele [-(α20.5] with an unstable α-globin variant [Hb Icaria]: first report on the occurrence in Brazil

    Directory of Open Access Journals (Sweden)

    Elza M. Kimura

    2009-01-01

    Full Text Available Hb H Disease is caused by the loss or inactivation of three of the four functional a-globin genes. Patients present chronic hemolytic anemia and splenomegaly. In some cases, occasional blood transfusions are required. Deletions are the main cause of this type of thalassemia (α-thalassemia. We describe here an unusual case of Hb H disease caused by the combination of a common αº deletion [-(α20.5] with a rare point mutation (c.427T > A, thus resulting in an elongated and unstable α-globin variant, Hb Icaria, (X142K, with 31 additional amino-acid residues. Very high levels of Hb H and Hb Bart's were detected in the patient's red blood cells (14.7 and 19.0%, respectively. This is the first description of this infrequent association in the Brazilian population.

  1. INEL metal recycle radioactive scrap metal survey report

    International Nuclear Information System (INIS)

    Funk, D.M.

    1994-09-01

    DOE requested that inventory and characterization of radioactive scrap metal (RSM) be conducted across the DOE complex. Past studies have estimated the metal available from unsubstantiated sources. In meetings held in FY-1993, with seven DOE sites represented and several DOE-HQ personnel present, INEL personnel discovered that these numbers were not reliable and that large stockpiles did not exist. INEL proposed doing in-field measurements to ascertain the amount of RSM actually available. This information was necessary to determine the economic viability of recycling and to identify feed stock that could be used to produce containers for radioactive waste. This inventory measured the amount of RSM available at the selected DOE sites. Information gathered included radionuclide content and chemical form, general radiation field, alloy type, and mass of metal

  2. Isolation and characterization of atrazine mineralizing Bacillus subtilis strain HB-6.

    Directory of Open Access Journals (Sweden)

    Jinhua Wang

    Full Text Available Atrazine is a widely used herbicide with great environmental concern due to its high potential to contaminate soil and waters. An atrazine-degrading bacterial strain HB-6 was isolated from industrial wastewater and the 16S rRNA gene sequencing identified HB-6 as a Bacillus subtilis. PCR assays indicated that HB-6 contained atrazine-degrading genes trzN, atzB and atzC. The strain HB-6 was capable of utilizing atrazine and cyanuric acid as a sole nitrogen source for growth and even cleaved the s-triazine ring and mineralized atrazine. The strain demonstrated a very high efficiency of atrazine biodegradation with a broad optimum pH and temperature ranges and could be enhanced by cooperating with other bacteria, suggesting its huge potential for remediation of atrazine-contaminated sites. To our knowledge, there are few Bacillus subtilis strains reported that can mineralize atrazine, therefore, the present work might provide some new insights on atrazine remediation.

  3. HbA2 measurements in β-thalassemia and in other conditions

    Directory of Open Access Journals (Sweden)

    Giovanni Ivaldi

    2014-09-01

    Full Text Available Quite a few papers have been written on the significance of elevated hemoglobin (Hb A2 as a parameter for the diagnosis of β-thalassemia trait, on the cutoff values to be used in diagnostics and on the significance and effects of factors reducing or elevating the expression of HbA2 and last but not least on the need for reliable measurement methods and precise calibrations with accurate standards. However, little has been published on the causes that elevate or reduce the HbA2 levels in β- and a-thalassemia and in other conditions. For a better understanding of the value of a precise measurement of this parameter we summarize and elucidate in this review the direct and indirect mechanisms that cause the variations in HbA2 expression and that influence the value of this parameter in particular conditions. We conclude by explaining the advantages and disadvantages of trusting on a precise measurement in the complete diagnostic contest.

  4. The changing relationship between HbA1c and FPG according to different FPG ranges.

    Science.gov (United States)

    Guan, X; Zheng, L; Sun, G; Guo, X; Li, Y; Song, H; Tian, F; Sun, Y

    2016-05-01

    Since the American Diabetes Association included hemoglobin A1c (HbA1c) in the diagnostic criteria for diabetes in 2010, the clinical use of HbA1c has remained controversial. We explored the use of HbA1c for diagnosing diabetes and intermediate hyperglycemia in comparison with fasting plasma glucose (FPG). We screened 3710 adult subjects (mean age = 55.24 years) comprising 1704 males and 2006 females. We drew an receiver operating characteristic (ROC) curve to evaluate the ability of HbA1c to diagnose diabetes and intermediate hyperglycemia according to FPG. We used Kappa coefficient and Pearson's correlation coefficient to evaluate the relationship between HbA1c and FPG in different FPG ranges. The areas under ROC curve to diagnose diabetes and intermediate hyperglycemia were 0.859 (95 % CI 0.827-0.892) and 0.633 (95 % CI 0.615-0.651). The kappa coefficients between FPG and HbA1c for diagnosis of diabetes and intermediate hyperglycemia were 0.601 (P HbA1c was 0.640 (P HbA1c and FPG changed according to the different FPG ranges. When FPG was higher, the relationship was stronger. HbA1c and FPG were highly consistent in diagnosing diabetes, but they were not in predicting intermediate hyperglycemia.

  5. Investment, replacement and scrapping in a vintage capital model with embodied technological change

    OpenAIRE

    Bitros, George C.; Hritonenko, Natali; Yatsenko, Yuri

    2007-01-01

    This paper analyzes and compares two alternative policies of determining the service life and replacement demand for vintage equipment under embodied technological change. The policies are the infinite-horizon replacement and the transitory replacement ending with scrapping. The corresponding vintage capital models are formulated in the dynamic optimization framework. These two approaches lead to different estimates of the duration of replacements and the impact of technological change on the...

  6. Optimal Lot Sizing with Scrap and Random Breakdown Occurring in Backorder Replenishing Period

    OpenAIRE

    Ting, Chia-Kuan; Chiu, Yuan-Shyi; Chan, Chu-Chai

    2011-01-01

    This paper is concerned with determination of optimal lot size for an economic production quantity model with scrap and random breakdown occurring in backorder replenishing period. In most real-life manufacturing systems, generation of defective items and random breakdown of production equipment are inevitable. To deal with the stochastic machine failures, production planners practically calculate the mean time between failures (MTBF) and establish the robust plan accordingly, in terms of opt...

  7. Hb and dyslipidaemia as predicting markers of serum alanine aminotransferase elevation in Chinese adolescents.

    Science.gov (United States)

    Chao, Kuo-Ching; Chang, Chun-Chao; Owaga, Eddy; Bai, Chyi-Huey; Huang, Tzu-chieh; Pan, Wen-Harn; Chang, Jung-Su

    2016-04-01

    Fe is an essential element for erythropoiesis and Hb synthesis. High Hb levels affect the blood's viscosity and are associated with cardiovascular dysfunction. The aim of the present study was to examine relationships of Hb and cardiometabolic abnormalities with the risk of alanine aminotransferase (ALT) elevation in adolescents. A population-based, cross-sectional study. National Nutrition and Health Survey in Taiwan (2010-2011, adolescents). Healthy adolescents aged 13-18 years. In total, 1941 adolescents (963 boys and 978 girls) were entered in the study. The mean age was 15·3 (sd 0·1) years (boys, 15·3 (sd 0·1) years; girls, 15·2 (sd 0·1) years). ALT tertile cut-off points for boys were 11 and 16 U/l, and for girls were 9 and 12 U/l. Girls without dyslipidaemia and presenting in the highest quartile (Q1) of Hb (>13·6 g/dl) were 1·89 and 3·76 times more likely to have raised serum ALT (9 and >12 U/l, respectively) than the reference (lowest quartile of Hb (Q1), 12 U/l) than the reference (Q1 of Hb, 15·4 g/dl), who were 7·40 times more likely to have elevated serum ALT of >16 U/l than the reference (Q1 of Hb, Hb level is a predictor of elevated serum ALT in adolescent girls with dyslipidaemia. Our study also highlights the importance of further research to establish cut-off points for Hb and its utility in diagnosing and preventing the onset of dyslipidaemia in adolescents.

  8. HbA1c as a predictor of diabetes after gestational diabetes mellitus.

    Science.gov (United States)

    Claesson, Rickard; Ignell, Claes; Shaat, Nael; Berntorp, Kerstin

    2017-02-01

    We wanted to investigate third-trimester HbA1c as a predictor of diabetes after gestational diabetes mellitus (GDM). Women with GDM were followed up prospectively for five years from pregnancy to detect the development of diabetes. The ability of HbA1c to predict diabetes was evaluated with receiver-operating characteristic (ROC) curves and logistic regression analysis. By five years, 73 of 196 women had been diagnosed with diabetes. An optimal cut-off point for HbA1c of 36mmol/mol (5.4%) could predict diabetes with 45% sensitivity and 92% specificity. For HbA1c ≥39mmol/mol (≥5.7%), sensitivity, specificity, and positive predictive value were 30%, 97%, and 91%, respectively. In logistic regression analysis, adjusting for the diagnostic glucose concentration during pregnancy, HbA1c levels in the upper quartile (≥36mmol/mol) were associated with a 5.5-fold increased risk of diabetes. Third-trimester HbA1c levels in the pre-diabetes range revealed women with post-partum diabetes with high specificity and high positive predictive value. HbA1c testing could be used as a strategy to select high-risk women for lifestyle interventions aimed at prevention of diabetes starting during pregnancy. The results should encourage further validation in other populations using new diagnostic criteria for GDM. Copyright © 2016 The Author(s). Published by Elsevier Ltd.. All rights reserved.

  9. Complex structure of the supernova remnant HB 3

    Science.gov (United States)

    Leahy, D. A.; Venkatesan, D.; Long, K. S.; Naranan, S.

    1985-01-01

    HB 3 is an old, large (84 pc diameter) supernova remnant associated with the W3 H II region/molecular cloud complex. Observations of the imaging proportional counter (IPC) onboard the Einstein X-ray astronomy satellite have been reprocessed to yield a contour map of X-ray brightness and spectra of various regions of this remnant. The measured IPC flux is 2.4 x 10 to the -11th ergs per sq cm per s, giving a 0.2-4 keV luminosity of 1.6 x 10 to the 35th ergs/s for a column densityof 6 x 10 to the 21st per sq cm. The measured X-ray temperatures reveal a decrease from center to limb of the remnant of 1-0.3 keV. HB 3 is in the late adiabatic blast-wave phase of evolution, 30,000 to 50,000 yr old and with an initial blast energy of 3 x 10 to the 50th ergs. The X-ray map is compared with available radio and optical images. In X-rays, HB 3 has two components - a diffuse emission inside the 84 pc radio remnant and a ring of emission at the center of 30 pc in diameter. The diffuse emission is similar to that from other supernova remnants which are moderately obscured (column density, nH approximately 10 to the 22nd per sq cm). Three possibilities for the origin of the ring are explored: (1) a second supernova remnant, (2) a shocked shell in the interstellar medium surrounding HB 3, and (3) reverse-shock heated ejecta. There is no hot neutron star within the remnant.

  10. Identification of diphtheria toxin R domain mutants with enhanced inhibitory activity against HB-EGF.

    Science.gov (United States)

    Suzuki, Keisuke; Mizushima, Hiroto; Abe, Hiroyuki; Iwamoto, Ryo; Nakamura, Haruki; Mekada, Eisuke

    2015-05-01

    Heparin-binding epidermal growth factor-like growth factor (HB-EGF), a ligand of EGF receptor, is involved in the growth and malignant progression of cancers. Cross-reacting material 197, CRM197, a non-toxic mutant of diphtheria toxin (DT), specifically binds to the EGF-like domain of HB-EGF and inhibits its mitogenic activity, thus CRM197 is currently under evaluation in clinical trials for cancer therapy. To develop more potent DT mutants than CRM197, we screened various mutant proteins of R domain of DT, the binding site for HB-EGF. A variety of R-domain mutant proteins fused with maltose-binding protein were produced and their inhibitory activity was evaluated in vitro. We found four R domain mutants that showed much higher inhibitory activity against HB-EGF than wild-type (WT) R domain. These R domain mutants suppressed HB-EGF-dependent cell proliferation more effectively than WT R domain. Surface plasmon resonance revealed their higher affinity to HB-EGF than WT R domain. CRM197(R460H) carrying the newly identified mutation showed increased cell proliferation inhibitory activity and affinity to HB-EGF. These results suggest that CRM197(R460H) or other recombinant proteins carrying newly identified mutation(s) in the R domain are potential therapeutics targeting HB-EGF. © The Authors 2014. Published by Oxford University Press on behalf of the Japanese Biochemical Society. All rights reserved.

  11. Research into the melting/refining of contaminated steel scrap arising in the dismantling of nuclear installations

    International Nuclear Information System (INIS)

    Harvey, D.S.

    1990-01-01

    The main part of this report is concerned with the steel-making behaviour of various radioisotopes encountered in steel from decommissioning of nuclear installations (e.g. cobalt 60, caesium 134 and europium 154). Under a wide range of conditions cobalt is largely absorbed by the steel, europium is absorbed by the slag, whereas caesium may be largely volatized, or largely absorbed by the slag. Radiation exposures which might occur during a large-scale recycling operation, during routine operations and accidents would not be significant according to published criteria in the UK. The second part of the report concerns the detection of radioactive materials which may be accidentally delivered to steelworks in scrap steel and used in steel-making. Detectors have been developed which would indicate the presence of radioactivity in scrap. A survey of the steelworks revealed areas where detection might be performed. Experiments have shown that a gamma ray detector of large volume could provide useful sensitivity of detection

  12. Registration of a High Yielding Malt Barley Variety HB1454 for the ...

    African Journals Online (AJOL)

    else

    Bayeh and Berhane 2011). Even though Ethiopia has favorable environment and .... malting profile for HB1454 is better than Beka for kernel weight, plump kernels, hectoliter weight and grain protein. HB1454 has shown relatively low percentage.

  13. FB-line neutron multiplicity counter operation manual

    International Nuclear Information System (INIS)

    Langner, D.G.; Sweet, M.R.; Salazar, S.D.; Kroncke, K.E.

    1998-01-01

    This manual describes the design features, performance, and operating characteristics for the FB-Line Neutron Multiplicity Counter (FBLNMC). The FBLNMC counts neutron multiplicities to quantitatively assay plutonium in many forms, including impure scrap and waste. Monte Carlo neutronic calculations were used to design the high-efficiency (57%) detector that has 113 3 H tubes in a high-density polyethylene body. The new derandomizer circuit is included in the design to reduce deadtime. The FBLNMC can be applied to plutonium masses in the range from a few tens of grams to 5 kg; both conventional coincidence counting and multiplicity counting can be used as appropriate. This manual gives the performance data and preliminary calibration parameters for the FBLNMC

  14. Update on Recovering Lead From Scrap Batteries

    Science.gov (United States)

    Cole, E. R.; Lee, A. Y.; Paulson, D. L.

    1985-02-01

    Previous work at the Bureau of Mines Rolla Research Center, U.S. Department of the Interior, resulted in successful development of a bench-scale, combination electrorefining-electrowinning method for recycling lead from scrap batteries by using waste fluosilicic acid (H2SiF6) as electrolyte.1,2 This paper describes larger scale experiments. Prior attempts to electrowin lead failed because large quantities of insoluble lead dioxide were deposited on the anodes at the expense of lead deposition on the cathodes. A major breakthrough was achieved with the discovery that lead dioxide formation at the anodes is prevented by adding a small amount of phosphorus to the electrolyte. The amount of PbO2 formed on the anodes during lead electrowinning was less than 1% of the total lead deposited on the cathodes. This work recently won the prestigious IR·100 award as one of the 100 most significant technological advances of 1984.

  15. Radioactive scrap metal decontamination technology assessment report

    International Nuclear Information System (INIS)

    Buckentin, J.M.; Damkroger, B.K.; Schlienger, M.E.

    1996-04-01

    Within the DOE complex there exists a tremendous quantity of radioactive scrap metal. As an example, it is estimated that within the gaseous diffusion plants there exists in excess of 700,000 tons of contaminated stainless steel. At present, valuable material is being disposed of when it could be converted into a high quality product. Liquid metal processing represents a true recycling opportunity for this material. By applying the primary production processes towards the material's decontamination and re-use, the value of the strategic resource is maintained while drastically reducing the volume of material in need of burial. Potential processes for the liquid metal decontamination of radioactively contaminated metal are discussed and contrasted. Opportunities and technology development issues are identified and discussed. The processes compared are: surface decontamination; size reduction, packaging and burial; melting technologies; electric arc melting; plasma arc centrifugal treatment; air induction melting; vacuum induction melting; and vacuum induction melting and electroslag remelting

  16. Scrap uranium recycling via electron beam melting

    International Nuclear Information System (INIS)

    McKoon, R.

    1993-11-01

    A program is underway at the Lawrence Livermore National Laboratory (LLNL) to recycle scrap uranium metal. Currently, much of the material from forging and machining processes is considered radioactive waste and is disposed of by oxidation and encapsulation at significant cost. In the recycling process, uranium and uranium alloys in various forms will be processed by electron beam melting and continuously cast into ingots meeting applicable specifications for virgin material. Existing vacuum processing facilities at LLNL are in compliance with all current federal and state environmental, safety and health regulations for the electron beam melting and vaporization of uranium metal. One of these facilities has been retrofitted with an auxiliary electron beam gun system, water-cooled hearth, crucible and ingot puller to create an electron beam melt furnace. In this furnace, basic process R ampersand D on uranium recycling will be performed with the goal of eventual transfer of this technology to a production facility

  17. First Cases of Hb Agrinio Described in Patients from the Republic of Macedonia.

    Science.gov (United States)

    Dimishkovska, Marija; Kuzmanovska, Maja; Kocheva, Svetlana; Martinova, Kata; Karanfilski, Oliver; Stojanoski, Zlate; Plaseska-Karanfilska, Dijana

    Previous molecular analyses of α-thalassemia (α-thal) in the Republic of Macedonia have identified the following genetic defects: -α 3.7 (rightward), -(α) 20.5 and - - MED I deletions and Hb Icaria [α142, Term→Lys (α2), HBA2: c.427T>A] and polyadenylation signal (polyA) [AATAAA>AATGAA (α2), HBA2: c.*92A>G] point mutations. Here, we report two unrelated patients from the Romani population in the Republic of Macedonia, homozygotes for the α2-globin gene variant Hb Agrinio [α29(B10)Leu→Pro; HBA2: c.89T>C]. To date, Hb Agrinio has been described only in individuals of Greek, Cypriot and Spanish origin. Both of our patients had early presentation of the disease (3.5 years and 2 months, respectively) with frequent blood transfusions from early infancy. They have a severe intermediate phenotype of thalassemia (Hb H disease) with hemoglobin (Hb) levels of 7.8 and 7.7 g/dL, respectively. Although the HBA2: c.89T>C mutation results in an α + allele, the severe phenotype of the homozygotes is due to the production of hyperunstable α chains that undergo post translational precipitation. This leads to a greater degree of red cell damage and hemolytic anemia. The detection of Hb Agrinio in two unrelated families of Romani ethnic origin, may suggest it is a founder mutation in this population living in the Republic of Macedonia. Considering the severity of the clinical presentation of the homozygotes or compound heterozygotes for this rare Hb variant, a targeted molecular screening for Hb Agrinio mutation carriers should be considered in all patients of Romani ethnic origin with manifested microcytosis.

  18. Design and qualification of an on-line permeator for the recovery of tritium from lead-lithium eutectic breeding alloy

    International Nuclear Information System (INIS)

    Veredas, G.; Fradera, J.; Fernandez, I.; Batet, L.; Penalva, I.; Mesquida, L.; Abella, J.; Sempere, J.; Martinez, I.; Herrazti, B.; Sedano, L.

    2011-01-01

    The fast and efficient recovery of bred tritium represents a major milestone of tritium breeding technologies R and D and is key for the demonstration of fusion reactor fuel self-sufficiency. For lead-lithium eutectic, diverse technologies are currently being investigated and qualified. Permeator Against Vacuum (PAV) solution represents a firm candidate because: (i) runs as a single-step process for tritium on-line recovery, (ii) works passively allowing to be thermally governed, (iii) can be easily in-pipe integrated in Pb15.7Li loop systems and (iv) can be conceived with high compactness. An optimal design of a PAV requires a detailed hydraulic design optimization for established operational ranges. An optimal PAV design is proposed and qualified by numerical simulation.

  19. To establish trimester-specific reference ranges for glycated haemoglobin (HbA1c) in pregnancy

    LENUS (Irish Health Repository)

    O'Connor, CM

    2011-09-01

    Background and aims: Diabetes in Pregnancy imposes additional risks to both mother and infant. These poor outcomes are considered to be primarily related to glycaemic control which is monitored longitudinally through pregnancy by means of HbA1c. The correlation between HbA1c levels with clinical outcomes emphasises the need to measure HbA1c accurately, precisely and for data interpretation comparison to appropriately defined reference intervals. From July 1st 2010, the HbA1c assay in Irish laboratories became fully metrologically traceable to the IFCC standard, permitting HbA1c to be reported in IFCC units (mmol\\/mol) and derived DCCT\\/NGSP units (%) using the IFCC-DCCT\\/NGSP master equation (DCCT = Diabetes Control and Complications Trial, NGSP = National Glycohemoglobin standardisation program). The aim of this project is to establish trimester-specific reference ranges in pregnancy for IFCC standardised HbA1c in non-diabetic Caucasian women. This will allow us to define the goal for HbA1c during pregnancy complicated by diabetes.\\r\

  20. Effects of a healthier snack on snacking habits and glycated Hb (HbA1c): a 6-week intervention study.

    Science.gov (United States)

    Yan, Mary R; Parsons, Andrew; Whalley, Gillian A; Rush, Elaine C

    2016-12-01

    Dietary behaviour modification may change eating habits and reduce the impact of poor nutrition. This study aimed to evaluate the effects of daily consumption of a healthier snack bar on snacking habits and glycated Hb (HbA1c) within a 6-week intervention. In all, twenty-eight participants were randomly allocated to two groups to either consume the bars as the main snack for 6 weeks (n 14) or receipt of the bars was delayed for 6 weeks (n 14) following a stepped-wedge design. All participants had HbA1c concentrations measured at weeks -1, 0, 4, 6, 10 and 12. A short dietary habits questionnaire was self-completed at weeks 0, 6 and 12. Participants consumed the bars they received instead of other snacks, and found that the healthier snack bar was acceptable as part of their daily dietary pattern. Over the 12 weeks, there was a significant reduction in intake of biscuits, cakes and pies (approximately 2 servings/week, Psnack intervention and a trend towards a favourable effect on glucose homoeostasis. Habitual snacking behaviour has the potential to be improved through changes in the food supply, and in the longer term may reduce the impact of poor nutrition on public health.

  1. Hb A1c Separation by High Performance Liquid Chromatography in Hemoglobinopathies

    OpenAIRE

    Chandrashekar, Vani

    2016-01-01

    Hb A1c measurement is subject to interference by hemoglobin traits and this is dependent on the method used for determination. In this paper we studied the difference between Hb A1c measured by HPLC in hemoglobin traits and normal chromatograms. We also studied the correlation of Hb A1c with age. Hemoglobin analysis was carried out by high performance liquid chromatography. Spearman's rank correlation was used to study correlation between A1c levels and age. Mann-Whitney U test was used to st...

  2. Hereditary Persistence of Fetal Hemoglobin Caused by Single Nucleotide Promoter Mutations in Sickle Cell Trait and Hb SC Disease.

    Science.gov (United States)

    Akinbami, Anthony O; Campbell, Andrew D; Han, Zeqiu J; Luo, Hong-Yuan; Chui, David H K; Steinberg, Martin H

    2016-01-01

    Hereditary persistence of fetal hemoglobin (HPFH) can be caused by point mutations in the γ-globin gene promoters. We report three rare cases: a child compound heterozygous for Hb S (HBB: c.20A > T) and HPFH with a novel point mutation in the (A)γ-globin gene promoter who had 42.0% Hb S, 17.0% Hb A and 38.0% Hb F; a man with Hb SC (HBB: c.19G > A) disease and a point mutation in the (G)γ-globin gene promoter who had 54.0% Hb S, 18.0% Hb C and 25.0% Hb F; a child heterozygous for Hb S and HPFH due to mutations in both the (A)γ- and (G)γ-globin gene promoters in cis [(G)γ(A)γ(β(+)) HPFH], with 67.0% Hb A, 6.5% Hb S and 25.0% Hb F.

  3. Submerged Glow-Discharge Plasma: An Economical Approach to Convert Construction Scrap Metal into Nanomaterials

    Directory of Open Access Journals (Sweden)

    Yek Peter Nai Yuh

    2018-01-01

    Full Text Available Submerged glow-discharge plasma (SGDP is relatively new among the various methods available for nanomaterials synthesis (NMs techniques. This method allows great control over the production cost of nanomaterials synthesis. A lab-scale batch type SDGP technology has been constructed to produce nanomaterials and investigate the inter-relationship between plasma excitation voltages, electrodes submerged areas and electrolyte concentration. Metal oxide nanospheres has been synthesised from different electrolyte concentrations (1M-0.001M and characterized by Scanning Electron Microscopy (SEM and Energy Dispersive Spectroscopy (EDS. As the major results showed that the nanospheres are uniformly spherical with diameter size distribution are between 100 nm - 2μm. EDS analysis shown the nano-Iron Oxide have been formed. Scrap metal initially showed around 6.45% and 93.55% of Carbon and Iron composition respectively. After SGDP process to the scrap metal, Carbon content has increased to 34-35% and Iron content has reduced to around 15-40%. EDS results also shown the higher percentage of Iron amount has remained with lower electrolyte concentration and Current is proportionally related to submersion area of cathode.

  4. Hemoglobin A1c (HbA1c) Test: MedlinePlus Lab Test Information

    Science.gov (United States)

    ... page: https://medlineplus.gov/labtests/hemoglobina1chba1ctest.html Hemoglobin A1c (HbA1c) Test To use the sharing features on this page, please enable JavaScript. What is a hemoglobin A1c (HbA1c) test? A hemoglobin A1c (HbA1c) test measures ...

  5. Elevated HbA1c and Fasting Plasma Glucose in Predicting Diabetes Incidence Among Older Adults

    Science.gov (United States)

    Lipska, Kasia J.; Inzucchi, Silvio E.; Van Ness, Peter H.; Gill, Thomas M.; Kanaya, Alka; Strotmeyer, Elsa S.; Koster, Annemarie; Johnson, Karen C.; Goodpaster, Bret H.; Harris, Tamara; De Rekeneire, Nathalie

    2013-01-01

    OBJECTIVE To determine which measures—impaired fasting glucose (IFG), elevated HbA1c, or both—best predict incident diabetes in older adults. RESEARCH DESIGN AND METHODS From the Health, Aging, and Body Composition study, we selected individuals without diabetes, and we defined IFG (100–125 mg/dL) and elevated HbA1c (5.7–6.4%) per American Diabetes Association guidelines. Incident diabetes was based on self-report, use of antihyperglycemic medicines, or HbA1c ≥6.5% during 7 years of follow-up. Logistic regression analyses were adjusted for age, sex, race, site, BMI, smoking, blood pressure, and physical activity. Discrimination and calibration were assessed for models with IFG and with both IFG and elevated HbA1c. RESULTS Among 1,690 adults (mean age 76.5, 46% men, 32% black), 183 (10.8%) developed diabetes over 7 years. Adjusted odds ratios of diabetes were 6.2 (95% CI 4.4–8.8) in those with IFG (versus those with fasting plasma glucose [FPG] HbA1c (versus those with HbA1c HbA1c were considered together, odds ratios were 3.5 (1.9–6.3) in those with IFG only, 8.0 (4.8–13.2) in those with elevated HbA1c only, and 26.2 (16.3–42.1) in those with both IFG and elevated HbA1c (versus those with normal FPG and HbA1c). Addition of elevated HbA1c to the model with IFG resulted in improved discrimination and calibration. CONCLUSIONS Older adults with both IFG and elevated HbA1c have a substantially increased odds of developing diabetes over 7 years. Combined screening with FPG and HbA1c may identify older adults at very high risk for diabetes. PMID:24135387

  6. Detection of the Unstable Hb Köln (HBB: c.295G>A) by a Capillary Electrophoresis Method.

    Science.gov (United States)

    Li, You-Qiong; Ye, Li-Hua; Mo, Yun

    2016-11-01

    Hb Köln (HBB: c.295G>A) is an unstable β-globin gene variant with a GTG>ATG substitution at codon 98. This variant is quite frequent in Europe and the USA but rare in China. It can easily be misdiagnosed as Hb Constant Spring (Hb CS; HBA2: c.427T>C) by high performance liquid chromatography (HPLC), but detection and quantification of both Hb Köln and degraded Hb Köln by capillary electrophoresis (CE) are possible. Thus, we concluded that CE was the preferred method for Hb Köln detection.

  7. Changing from glucose to HbA1c for diabetes diagnosis

    DEFF Research Database (Denmark)

    Nielsen, Aneta Aleksandra; Petersen, Per Hyltoft; Green, Anders

    2014-01-01

    BACKGROUND: In Denmark, the use of HbA1c in the diagnosis of diabetes was adopted from March 2012. We evaluated the change in the number of diabetes cases diagnosed by haemoglobin A1c (HbA1c) versus fasting venous plasma glucose (FPG), and estimated the influence of analytical variation and bias ...

  8. Antibacterial activity of a modified unfilled resin containing a novel polymerizable quaternary ammonium salt MAE-HB.

    Science.gov (United States)

    Huang, Li; Yu, Fan; Sun, Xiang; Dong, Yan; Lin, Ping-Ting; Yu, Hao-Han; Xiao, Yu-Hong; Chai, Zhi-Guo; Xing, Xiao-Dong; Chen, Ji-Hua

    2016-09-23

    Resins with strong and long-lasting antibacterial properties are critical for the prevention of secondary dental caries. In this study, we evaluated the antibacterial effect and the underlying mechanism of action of an unfilled resin incorporating 2-methacryloxylethyl hexadecyl methyl ammonium bromide (MAE-HB) against Streptococcus mutans UA159 (S. mutans UA159). MAE-HB was added into unfilled resin at 10 mass%, and unfilled resin without MAE-HB served as the control. Bacterial growth was inhibited on 10%-MAE-HB unfilled resin compared with the control at 1 d, 7 d, 30 d, or 180 d (P  0.05). No significant differences in the antibacterial activities of eluents from control versus 10%-MAE-HB unfilled resins were observed at any time point (P > 0.05). The number of bacteria attached to 10%-MAE-HB unfilled resin was considerably lower than that to control. Fe-SEM and CLSM showed that 10%-MAE-HB unfilled resin disturbed the integrity of bacterial cells. Expression of the bacterial glucosyltransferases, gtfB and gtfC, was lower on 10%-MAE-HB unfilled resin compared to that on control (P HB confers unfilled resin with strong and long-lasting antibacterial effects against S. mutans.

  9. Distribution, enrichment and accumulation of heavy metals in coastal sediments of Alang-Sosiya ship scrapping yard, India.

    Science.gov (United States)

    Reddy, M Srinivasa; Basha, Shaik; Sravan Kumar, V G; Joshi, H V; Ramachandraiah, G

    2004-06-01

    Since its inception in 1982, the Alang-Sosiya yard has become the largest ship scrapping works in the world. Several hundreds of ships arrive every year. The degree of heavy metal contamination has been studied in bulk and fine sediments from the intertidal zone of this ship scrapping yard, two stations, one on either side at 5 km distance and one reference station 60 km distance near Mahuva, towards the south. The samples have been subjected to a total digestion technique and analysed for elements: Cd, Co, Cu, Cr, Fe, Mn, Ni, Pb, Zn and Al, and %TOC. The absolute metal concentrations reflected variations in BF and FF sediment samples with organic matter content. Enrichment factors (EF) and geoaccumulation indices (Igeo) have been calculated and the relative contamination levels are assessed at these sites. At Alang-Sosiya, the enrichment of heavy metals has been observed to be relatively high.

  10. Changes in proHB-EGF expression after functional activation of the immune system cells

    Directory of Open Access Journals (Sweden)

    T. O. Chudina

    2017-12-01

    Full Text Available The level of proHB-EGF expression on J774, Raji, KG-1 cells derived from different types of human and mouse immune system cells under the standard in vitro culture conditions and during functional activation of these cells was investigated. Changes in the proHB-EGF expression on the cell surface were found to depend on the density of cell population, the content of fetal bovine serum in the culture medium, the effect of mitogenic factors – bacterial lipopolysaccharide, an inactive full-size form of diphtheria toxin (CRM197 and recombinant soluble HB-EGF – rsHB-EGF. The results obtained are important for the understanding of the functional role of proHB-EGF receptor on the surface of macrophage-like cells and B lymphocytes and indicate the involvement of this receptor in immune response regulation in an organism.

  11. Simulation and control synthesis for a pulse column separation system for plutonium--uranium recovery

    International Nuclear Information System (INIS)

    McCutcheon, E.B.

    1975-05-01

    Control of a plutonium-uranium partitioning column was studied using a mathematical model developed to simulate the dynamic response and to test postulated separation mechanisms. The column is part of a plutonium recycle flowsheet developed for the recovery of plutonium and uranium from metallurgical scrap. In the first step of the process, decontamination from impurities is achieved by coextracting plutonium and uranium in their higher oxidation states. In the second step, reduction of the plutonium to a lower oxidation state allows partitioning of the plutonium and uranium. The use of hydroxylamine for the plutonium reduction in this partitioning column is a unique feature of the process. The extraction operations are carried out in pulse columns. (U.S.)

  12. Mild Microcytic Anemia in an Infant with a Compound Heterozygosity for Hb C (HBB: c.19G > A) and Hb Osu Christiansborg (HBB: c.157G > A).

    Science.gov (United States)

    Boucher, Maria O; Chui, David H K; Woda, Bruce A; Newburger, Peter E

    2016-06-01

    We report an infant with a compound heterozygosity for Hb C (HBB: c.19G > A) and Hb Osu Christiansborg (HBB: c.157G > A) and a phenotype of mild microcytic anemia with target cell morphology but without overt hemolysis.

  13. An alternative approach to modelling HbA1c trajectories in patients with type 2 diabetes mellitus.

    Science.gov (United States)

    McEwan, Phil; Bennett, Hayley; Qin, Lei; Bergenheim, Klas; Gordon, Jason; Evans, Marc

    2017-05-01

    Time-dependent HbA1c trajectories in health economic models of type 2 diabetes mellitus (T2DM) are typically informed by the UK Prospective Diabetes Study (UKPDS). However, this approach may not accurately predict HbA1c progression in patients who do not conform to the demographic profile of the original UKPDS cohort. This study aimed to develop an alternative mathematical model (MM) to simulate HbA1c progression in T2DM. A systematic literature review identified studies, published between 2005 and 2015, that reported HbA1c in adult T2DM patients over a minimum duration of 18 months. Pooled data from eligible studies were used to develop an alternative MM equation for HbA1c progression, which was then contrasted with the UKPDS 68 progression equation in illustrative scenarios. A total of 68 studies were eligible for data extraction (mean follow-up time 4.1 years). HbA1c progression was highly heterogeneous across studies, varying with baseline HbA1c, treatment group and patient age. The MM equation was fitted with parameters for mean baseline HbA1c (8.3%), initial change in HbA1c (-0.62%) and upper quartile of maximum observed HbA1c (9.3%). Differences in HbA1c trajectories between the MM and UKPDS approaches altered the timing of therapy escalation in illustrative scenarios. The MM represents an alternative approach to simulate HbA1c trajectories in T2DM models, as UKPDS data may not adequately reflect the heterogeneity of HbA1c profiles observed in clinical studies. However, the choice of approach should ultimately be determined by the characteristics of individual patients under consideration and the clinical face validity of the modelled trajectories. © 2016 John Wiley & Sons Ltd.

  14. Biotechnological recovery of heavy metals from secondary sources-An overview

    International Nuclear Information System (INIS)

    Hoque, Md E.; Philip, Obbard J.

    2011-01-01

    The demand for heavy metals is ever increasing with the advance of the industrialized world, whereas worldwide reserves of high-grade ores are diminishing. However, there exist large stockpiles of low and lean grade ores that are yet to be exploited. In addition, heavy metals that are present in a spectrum of waste streams including mine drainage, industrial effluents, river sediments, electronic scraps and ashes are also available for recovery and utilization. Heavy metal recovery from low and lean grade ores using conventional techniques such as pyrometallurgy, etc. chemical metallurgy encompass several inherent constraints like, high energy and capital inputs, and high risk of secondary environmental pollution. As environmental regulations become ever more stringent, particularly regarding the disposal of toxic wastes, the costs for ensuring environmental protection will continue to rise. Therefore, there is a need to utilize more efficient technologies to recover heavy metals from secondary sources in order to minimize capital outlay, environmental impact and to respond to increased demand. Biohydrometallurgy, which exploits microbiological processes to recover heavy metal ions, is regarded as one of the most promising and revolutionary biotechnologies. The products of such processes are deposited in aqueous solution thereby rendering them to be more amenable to containment, treatment and recovery. On top of this, biohydrometallurgy can be conducted under mild conditions, usually without the use of any toxic chemicals. Consequently, the application of biohydrometallurgy in recovery of heavy metals from lean grade ores, and wastes, has made it an eco-friendly biotechnology for enhanced heavy metal production.

  15. Biotechnological recovery of heavy metals from secondary sources-An overview

    Energy Technology Data Exchange (ETDEWEB)

    Hoque, Md E., E-mail: enamul.hoque@nottingham.edu.my [Department of Mechanical, Materials and Manufacturing Engineering, University of Nottingham Malaysia Campus, Jalan Broga, 43500 Semenyih, Selangor Darul Ehsan (Malaysia); Philip, Obbard J., E-mail: esejpo@nus.edu.sg [Division of Environmental Science and Engineering, National University of Singapore, 119260 (Singapore)

    2011-03-12

    The demand for heavy metals is ever increasing with the advance of the industrialized world, whereas worldwide reserves of high-grade ores are diminishing. However, there exist large stockpiles of low and lean grade ores that are yet to be exploited. In addition, heavy metals that are present in a spectrum of waste streams including mine drainage, industrial effluents, river sediments, electronic scraps and ashes are also available for recovery and utilization. Heavy metal recovery from low and lean grade ores using conventional techniques such as pyrometallurgy, etc. chemical metallurgy encompass several inherent constraints like, high energy and capital inputs, and high risk of secondary environmental pollution. As environmental regulations become ever more stringent, particularly regarding the disposal of toxic wastes, the costs for ensuring environmental protection will continue to rise. Therefore, there is a need to utilize more efficient technologies to recover heavy metals from secondary sources in order to minimize capital outlay, environmental impact and to respond to increased demand. Biohydrometallurgy, which exploits microbiological processes to recover heavy metal ions, is regarded as one of the most promising and revolutionary biotechnologies. The products of such processes are deposited in aqueous solution thereby rendering them to be more amenable to containment, treatment and recovery. On top of this, biohydrometallurgy can be conducted under mild conditions, usually without the use of any toxic chemicals. Consequently, the application of biohydrometallurgy in recovery of heavy metals from lean grade ores, and wastes, has made it an eco-friendly biotechnology for enhanced heavy metal production.

  16. NEAR-IR PHOTOMETRIC PROPERTIES OF HB, MSTO, AND SGB FOR METAL POOR GALACTIC GLOBULAR CLUSTERS

    Directory of Open Access Journals (Sweden)

    J.-W. Kim

    2007-03-01

    Full Text Available We report photometric features of the HB, MSTO, and SGB for a set of metal-poor Galactic globular clusters on the near-IR CMDs. The magnitude and color of the MSTO and SGB are measured on the fiducial normal points of the CMDs by applying a polynomial fit. The near-IR luminosity functions of horizontal branch stars in the classical second parameter pair M3 and M13 indicate that HB stars in M13 are dominated by hot stars that are rotatively faint in the infrared, whereas HB stars in M3 are brighter than those in M13. The luminosity functions of HB stars in the observed bulge clusters, except for NGC 6717, show a trend that the fainter hot HB stars are dominated in the relatively metal-poor clusters while the relatively metal-rich clusters contain the brighter HB stars. It is suggestive that NGC 6717 would be an extreme example of the second-parameter phenomenon for the bulge globular clusters.

  17. [Application of the polymerase chain reaction (PCR) in the diagnosis of Hb S-beta(+)-thalassemia].

    Science.gov (United States)

    Harano, K; Harano, T; Kushida, Y; Ueda, S

    1991-08-01

    Isoelectric focusing of the hemolysate prepared from a two-year-old American black boy with microcytic hypochromia showed the presence of a high percentage (63.3%) of such Hb variant as Hb S, while the levels of Hb A, Hb F and Hb A2 were 20.0%, 12.7%, and 4.0%, respectively. The ratio of the non-alpha-chain to the alpha-chain of the biosynthesized globin chains was 0.49. The variant was identified as Hb S by amino acid analysis of the abnormal peptide (beta T-1) and digestion of DNA amplified by the polymerase chain reaction with enzyme Eco 81 I. This was further confirmed by DNA sequencing. DNA sequencing of a beta-gene without the beta s-mutation revealed a nucleotide change of T to C in the polyadenylation signal sequence AATAAA 3' to the beta-gene, resulting in beta(+)-thalassemia. These results are consistent with the existence of a beta s-gene and a beta(+)-thalassemia gene in trans.

  18. Association of plasma PCB levels and HbA1c concentration in Iran.

    Science.gov (United States)

    Eftekhari, Sahar; Aminian, Omid; Moinfar, Zeinab; Schettgen, Thomas; Kaifie, Andrea; Felten, Michael; Kraus, Thomas; Esser, André

    2018-01-01

    The rapid increase in prevalence of diabetes mellitus over the last decades warrants more attention to the effects of environmental and occupational exposures on glucose metabolism. Our study aimed to assess the association between the plasma levels of various congeners of polychlorinated biphenyls (PCBs) and the serum concentration of glycated haemoglobin (HbA1c). Our study population consisted of 140 Iranian adults from seven different occupational groups and a group of non-occupationally exposed female participants. The plasma concentration of PCBs were determined at the laboratory of occupational toxicology at RWTH Aachen University, Germany. We considered an HbA1c concentration of 5.7% and more as indicating a disturbed glucose metabolism. Logistic regression was used to assess the association between quartiles of concentrations of PCB congeners and serum HbA1c. Participants with an increased HbA1c value had higher plasma levels of PCB 138, 153, 180 and the PCB sum, although this association was statistically not significant. There was no significant difference between the levels of PCB 138, 153, 180, the sum of these congeners, and PCB 118 in their quartiles when comparing with HbA1c concentrations. For our cohort, we could not demonstrate a significant association between PCB and HbA1c concentrations indicating a disturbance of glucose metabolism.

  19. HbA1c, systolic blood pressure variability and diabetic retinopathy in Asian type 2 diabetics.

    Science.gov (United States)

    Foo, Valencia; Quah, Joanne; Cheung, Gemmy; Tan, Ngiap Chun; Ma Zar, Kyi Lin; Chan, Choi Mun; Lamoureux, Ecosse; Tien Yin, Wong; Tan, Gavin; Sabanayagam, Charumathi

    2017-02-01

    The aim of the present study was to examine the association between variability in HbA1c or systolic blood pressure (SBP) and diabetes-specific moderate retinopathy in Asians with type 2 diabetes (T2D). A retrospective study was conducted of 172 cases of moderate diabetic retinopathy (DR) cases and 226 controls without DR, matched for age, sex, and ethnicity. Serial HbA1c and SBP (range 3-6 readings) over the 2 years prior to photographic screening of DR were collected. Intrapersonal mean and SD values for HbA1c (iM-HbA1c and iSD-HbA1c) and SBP (iM-SBP and iSD-SBP) were derived. Moderate DR was assessed from digital retinal photographs and defined as levels >43 using the Early Treatment Diabetic Retinopathy Study scale. Cases of moderate DR had higher iM-HbA1c (8.2 % vs 7.3 %; P = 0.001), iSD-HbA1c (1.22 vs 0.64; P = 0.001), iM-SBP (136.8 vs 129.6 mmHg; P = 0.001) and iSD-SBP (13.3 vs 11.1; P = 0.002) than controls. In the multivariate regression model adjusted for age, gender, ethnicity, duration of diabetes, SBP, and HbA1c, iM-HbA1c and iM-SBP were significantly associated with moderate DR (odds ratio [OR] 1.80, 95 % confidence interval [CI] 1.37-2.36; and OR 1.03, 95 % CI 1.01-1.05, respectively). Neither iSD-HbA1c nor iSD-SBP were associated with moderate DR. When stratified by HbA1c HbA1c levels and SBP, but not their variability, were associated with moderate DR. Among those with good glycemic control, wider variability of SBP is associated with moderate DR. © 2016 Ruijin Hospital, Shanghai Jiaotong University School of Medicine and John Wiley & Sons Australia, Ltd.

  20. Analytical verification and quality assessment of the Tosoh HLC-723GX HbA1c analyzer

    Directory of Open Access Journals (Sweden)

    Marko Ris

    2017-04-01

    Full Text Available Objectives: Ion-exchange high-performance liquid chromatography (IE-HPLC has long been used as a reproducible and versatile analytical tool for HbA1c measurement.In this study, we performed analytical verification and quality assessment of the recently introduced small IE-HPLC Tosoh HLC-723GX HbA1c analyzer, and a comparison of results to immunoassay (IA and capillary electrophoresis (CE. Design and methods: The total imprecision of Tosoh HLC-723GX was verified according to CLSI EP15-A2 protocol using commercial control materials (C-QC and pooled human whole blood samples (HWB. The Sigma metric was used for the evaluation of quality targets. HbA1c results were compared to automated CE (MiniCap Flex Piercing, Sebia, France and IA (Tina-quant HbA1c Gen 2, Cobas Integra 400+, Roche Diagnostics, USA procedures. Results: The total imprecision of Tosoh HLC-723GX-HbA1c for IFCC(mmol/mol and NGSP(% units was: 1.91/1.25% (HbA1c=31 mmol/mol/5.0% and 0.51/0.63% (HbA1c=84 mmol/mol/9.8% for C-QC, and 0.39/0.2% (HbA1c=47 mmol/mol/6.5% and 0.77/0.46% (HbA1c=94 mmol/mol/10.8% in HWB samples, respectively. Bland-Altman analysis did not reveal any deviation of the results between Tosoh HLC-723GX and CE: mean difference 0.0% (95%CI: −0.02927 to 0.02653%, while the mean HbA1c difference against IA was −0.07% (95%CI: −0.1039 to −0.02765. At the selected HbA1c clinical decision level (48 mmol/mol/6,5%, six sigma analysis gave σ value of 3.91, within a desirable classification of performance. Conclusion: The analytical performance of the Tosoh HLC-723GX complies with the rigorous quality criteria for clinical use of HbA1c, with the results comparable to the CE procedure. Tosoh HLC-723GX provides a plausible analytical choice for reliable HbA1c measurement in low-volume laboratories. Keywords: HbA1c, Quality targets, Six sigma, Tosoh HLC-723GX analyzer