Hazardous materials routing - risk management of mismanagement

International Nuclear Information System (INIS)

Glickman, T.S.

1988-01-01

Along with emergency planning and preparedness, the placement of restrictions on routing has become an increasingly popular device for managing the highway and rail risks of hazardous materials transportation. Federal studies conducted in 1985 indicate that at that time there were 513 different state and local restrictions on the routing of hazardous materials for these two modes of transportation, and that there were 136 state and local notification requirements, that is, restrictions that take the form of a statute or ordinance requiring advance warning or periodic reporting about hazardous materials shipments. Routing restrictions also take the form of prohibiting the use of road, a tunnel, or a bridge for a specified set of hazardous materials

76 FR 51324 - Hazardous Materials: Incorporating Rail Special Permits Into the Hazardous Materials Regulations

Science.gov (United States)

2011-08-18

... through use of electronic data interchange (EDI). The IVOHMA states ``differences in hazard communication... and on the possible effects EDI may have on distributing hazardous materials shipping paper... consider the use of EDI in other modes of transport in a future rulemaking. Petition No. P-1567 PHMSA...

A comprehensive approach to managing hazardous materials

International Nuclear Information System (INIS)

Donovan, A.

1990-01-01

An increased emphasis on the need for environmental protection indicates that engineers must now consider the disposition of unused hazardous materials as waste. Before specifying and ordering materials, the engineer must consider the impact of the Resource Conservation and Recovery Act (RCRA) and the Occupational Safety and Health Administration's (OSHA's) Hazard Communication Standard. Many commonly used materials such as paint, solvents, glues, and sealants fall under the requirements of these regulations. This paper presents a plant to manage hazardous materials at the US Department of Energy's (DOE's) Waste Isolation Pilot Plant (WIPP), which is managed and operated by Westinghouse Electric Corporation. The basic elements of the plan are training, hazard communication, storage and handling, tracking, and disposal. Steps to be taken to develop the plan are outlined, problems and successes are addressed, and interactions among all affected departments are identified. The benefits of an organized and comprehensive approach to managing hazardous materials are decreased worker injuries, reduction of accidental releases, minimization of waste, and compliance with federal, state, and local safety and environmental laws. In summary, the benefits of an organized program for the management of hazardous materials include compliance with the Environmental Protection Agency's (EPA's) requirements, demonstration of Westinghouse's role as a responsible corporate entity, and reduction of waste management costs

30 CFR 56.16004 - Containers for hazardous materials.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Containers for hazardous materials. 56.16004 Section 56.16004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 56.16004 Containers for hazardous materials. Containers holding hazardous materials...

30 CFR 57.16004 - Containers for hazardous materials.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Containers for hazardous materials. 57.16004 Section 57.16004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 57.16004 Containers for hazardous materials. Containers holding hazardous materials...

Hazardous materials and waste management a guide for the professional hazards manager

CERN Document Server

Cheremisinoff, Nicholas P

1995-01-01

The management of hazardous materials and industrial wastes is complex, requiring a high degree of knowledge over very broad technical and legal subject areas. Hazardous wastes and materials are diverse, with compositions and properties that not only vary significantly between industries, but within industries, and indeed within the complexity of single facilities. Proper management not only requires an understanding of the numerous and complex regulations governing hazardous materials and waste streams, but an understanding and knowledge of the treatment, post-treatment, and waste minimizatio

Hazardous Material Packaging and Transportation

Energy Technology Data Exchange (ETDEWEB)

Hypes, Philip A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-02-04

This is a student training course. Some course objectives are to: recognize and use standard international and US customary units to describe activities and exposure rates associated with radioactive material; determine whether a quantity of a single radionuclide meets the definition of a class 7 (radioactive) material; determine, for a given single radionuclide, the shipping quantity activity limits per 49 Code of Federal Regulations (CFR) 173.435; determine the appropriate radioactive material hazard class proper shipping name for a given material; determine when a single radionuclide meets the DOT definition of a hazardous substance; determine the appropriate packaging required for a given radioactive material; identify the markings to be placed on a package of radioactive material; determine the label(s) to apply to a given radioactive material package; identify the entry requirements for radioactive material labels; determine the proper placement for radioactive material label(s); identify the shipping paper entry requirements for radioactive material; select the appropriate placards for a given radioactive material shipment or vehicle load; and identify allowable transport limits and unacceptable transport conditions for radioactive material.

Health and safety information program for hazardous materials

International Nuclear Information System (INIS)

O'Brien, M.P.; Fallon, N.J.; Kuehner, A.V.

1979-01-01

The system is used as a management tool in several safety and health programs. It is used to: trace the use of hazardous materials and to determine monitoring needs; inform the occupational physician of the potential health problems associated with materials ordered by a given individual; inform the fire and rescue group of hazardous materials in a given building; provide waste disposal recommendations to the hazardous waste management group; assist the hazardous materials shipping coordinator in identifying materials which are regulated by the Department of Transportation; and guide management decisions in the area of recognizing and rectifying unsafe conditions. The information system has been expanded from a manual effort to provide a brief description of health hazards of chemicals used at the lab to a computerized health and safety information system which serves the needs of all personnel who may encounter the material in the course of their work. The system has been designed to provide information needed to control the potential problems associated with a hazardous material up to the time that it is consumed in a given operation or is sent to the waste disposal facility

Report 5: Guidance document. Implementation of biological infestation hazards in extended PSA

International Nuclear Information System (INIS)

Hasnaoui, C.; Georgescu, G.; Joel, P.; Sperbeck, S.; Kollasko, H.; Kumar, M.

2016-01-01

This report covers the assessment of biological hazards with PSA. It provides an overview of the available data and available practices in modelling this type of hazard. First researches in the national and international literature regarding PSA for external and internal hazards shows that probabilistic analyses were very rarely carried out in order to quantify the risk induced by biological hazards. Nevertheless, Section 3 provides some data from some countries. History has shown that this hazard can happened and can be highly safety significant. Screening out this event must be done with great care. The overall analysis approach for Level 1 PSA for internal events can be used for the biological hazards with some care to take into impact the nature of the hazard as it impacts many systems at different times and duration. A proposed detailed methodology is described in Section 4. Still some open issues remain: the methodology must also consider event combination of biological infestation with other external hazards wind or flooding or rainfall and multi-units impact. These aspects present still a lot of challenges to PSA developers. The ASAMPSA-E report recommends that further emphasis shall be put on these two aspects of PSA modelling: multi-units site impact and hazards combinations. (authors)

78 FR 24309 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2013-04-24

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration List of Special Permit Applications Delayed AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA..., Pipeline and Hazardous Materials Safety Administration, U.S. Department of Transportation, East Building...

76 FR 45332 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2011-07-28

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration Office of... Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: List of Applications for Modification of..., 2011. ADDRESSES: Record Center, Pipeline and Hazardous Materials Safety Administration, U.S. Department...

Transportation of hazardous materials (hazmat) a literature survey

OpenAIRE

Zafer YILMAZ; Serpil EROL; Hakan Soner APLAK

2016-01-01

ransportation has a great role in logistics. Many researchers have studied on transportation and vehicle routing problems. Transportation of hazardous materials (hazmat) is a special subject for logistics. Causalities due to the accidents caused by trucks carrying hazardous materials will be intolerable. Many researchers have studied on risk assessment of hazmat transportation to find ways for reducing hazardous material transportation risks. Some researchers have studied routing of hazmat tr...

Navy Shipboard Hazardous Material Minimization Program

Energy Technology Data Exchange (ETDEWEB)

Bieberich, M.J. [Naval Surface Warfare Center, Annapolis, MD (United States). Carderock Div.; Robinson, P. [Life Cycle Engineering, Inc., Charleston, SC (United States); Chastain, B.

1994-12-31

The use of hazardous (and potentially hazardous) materials in shipboard cleaning applications has proliferated as new systems and equipments have entered the fleet to reside alongside existing equipments. With the growing environmental awareness (and additional, more restrictive regulations) at all levels/echelon commands of the DoD, the Navy has initiated a proactive program to undertake the minimization/elimination of these hazardous materials in order to eliminate HMs at the source. This paper will focus on the current Shipboard Hazardous Materials Minimization Program initiatives including the identification of authorized HM currently used onboard, identification of potential substitute materials for HM replacement, identification of new cleaning technologies and processes/procedures, and identification of technical documents which will require revision to eliminate the procurement of HMs into the federal supply system. Also discussed will be the anticipated path required to implement the changes into the fleet and automated decision processes (substitution algorithm) currently employed. The paper will also present the most recent technologies identified for approval or additional testing and analysis including: supercritical CO{sub 2} cleaning, high pressure blasting (H{sub 2}O + baking soda), aqueous and semi-aqueous cleaning materials and processes, solvent replacements and dedicated parts washing systems with internal filtering capabilities, automated software for solvent/cleaning process substitute selection. Along with these technological advances, data availability (from on-line databases and CDROM Database libraries) will be identified and discussed.

EFSA Panel on Biological Hazards (BIOHAZ); Scientific Opinion on Composting and incineration of dead-on-farm pigs

DEFF Research Database (Denmark)

Hald, Tine

of biological hazards throughout the farm environment. Major deficiencies were noted in relation to the risk containment. Moreover, a formal HACCP plan was not provided, and some deficiencies were also noted in the identification of interdependent processes. Provided that the deficiencies identified......A method for on-farm processing of Category (Cat) 2 Animal By-Products (ABP) alternative to the ones already approved in the current legislation was assessed. The materials to be treated are placentas and dead-on-farm pigs. The proposed process consists of three sequential steps, i.e. composting......, storage of mature compost and incineration of mature compost in authorized plants. The applicant identified the main biological, physical and chemical hazards that could be present in the material to be treated and in the compost substrate. Since the compost is only intended for incineration the applicant...

Double-pulse standoff laser-induced breakdown spectroscopy for versatile hazardous materials detection

Energy Technology Data Exchange (ETDEWEB)

Gottfried, Jennifer L. [U.S. Army Research Laboratory, AMSRD-ARL-WM-BD, Aberdeen Proving Ground, MD, 21005-5069 (United States)], E-mail: jennifer.gottfried@arl.army.mil; De Lucia, Frank C.; Munson, Chase A.; Miziolek, Andrzej W. [U.S. Army Research Laboratory, AMSRD-ARL-WM-BD, Aberdeen Proving Ground, MD, 21005-5069 (United States)

2007-12-15

We have developed a double-pulse standoff laser-induced breakdown spectroscopy (ST-LIBS) system capable of detecting a variety of hazardous materials at tens of meters. The use of a double-pulse laser improves the sensitivity and selectivity of ST-LIBS, especially for the detection of energetic materials. In addition to various metallic and plastic materials, the system has been used to detect bulk explosives RDX and Composition-B, explosive residues, biological species such as the anthrax surrogate Bacillus subtilis, and chemical warfare simulants at 20 m. We have also demonstrated the discrimination of explosive residues from various interferents on an aluminum substrate.

EFSA BIOHAZ Panel (EFSA Panel on Biological Hazards), 2013. Scientific Opinion on Bioreduction application

DEFF Research Database (Denmark)

Hald, Tine; Baggesen, Dorte Lau

A method for on-farm containment of animal by-products (ABPs), called a ‘Bioreduction’ system, was assessed. The material for containment is of ovine origin and classified as a Category (Cat.) 1 ABP material. The proposed process consists of an aerobic degradation of the ABP material in a vented...... the risks related to pathogens such as non-spore forming bacteria and viruses. However, it is highly improbable that the risks related to more resistant biological hazards can be reduced. The application does not provide clear information about the location of the system and the origin of the material...... the risk of aerogenic transmission of biological agents and it is accessible to living vectors. Moreover, there is a risk of release of pathogens to the environment when opening the vessel. Therefore, the whole system cannot be considered as a closed system. The proposed Bioreduction method cannot...

US Hazardous Materials Routes, Geographic WGS84, BTS (2006) [hazardous_material_routes_BTS_2006

Data.gov (United States)

Louisiana Geographic Information Center — The Federal Motor Carrier Safety Administration (FMCSA) Hazardous Material Routes were developed using the 2004 First Edition TIGER/Line files. The routes are...

The Main Biological Hazards in Animal Biosafety Level 2 Facilities and Strategies for Control.

Science.gov (United States)

Li, Xiao Yan; Xue, Kang Ning; Jiang, Jin Sheng; Lu, Xuan Cheng

2016-04-01

Concern about the biological hazards involved in microbiological research, especially research involving laboratory animals, has increased in recent years. Working in an animal biosafety level 2 facility (ABSL-2), commonly used for research on infectious diseases, poses various biological hazards. Here, the regulations and standards related to laboratory biosafety in China are introduced, the potential biological hazards present in ABSL-2 facilities are analyzed, and a series of strategies to control the hazards are presented. Copyright © 2016 The Editorial Board of Biomedical and Environmental Sciences. Published by China CDC. All rights reserved.

EFSA Panel on Biological Hazards (BIOHAZ); Scientific Opinion on On-site treatment of pig carcasses

DEFF Research Database (Denmark)

Hald, Tine

EFSA’s Scientific Panel on Biological Hazards (BIOHAZ) was asked for a scientific opinion on an alternative method for processing Category (Cat) 2 Animal By-Products (ABP). The materials to be treated are placentas and fallen pigs; this implies that the animals died due to a disease, which in most...... of the animals’ death, the presence of more resistant hazards cannot be considered negligible. The sterilisation process defined in the current legislation is able to minimise the risks due to unidentified agents, such as Bacillus anthracis and TSE agents. The BIOHAZ Panel concluded that the process proposed...

Hazardous materials package performance regulations

International Nuclear Information System (INIS)

Russell, N.A.; Glass, R.E.; McClure, J.D.; Finley, N.C.

1992-01-01

The hazardous materials (hazmat) packaging development and certification process is currently defined by two different regulatory philosophies, one based on specification packagings and the other based on performance standards. With specification packagings, a packaging is constructed according to an agreed set of design specifications. In contrast, performance standards do not specify the packaging design; they specify performance standards that a packaging design must be able to pass before it can be certified for transport. The packaging can be designed according to individual needs as long as it meets these performance standards. Performance standards have been used nationally and internationally for about 40 years to certify radioactive materials (RAM) packagings. It is reasonable to state that for RAM transport, performance specifications have maintained transport safety. A committee of United Nation's experts recommended the performance standard philosophy as the preferred regulation method for hazmat packaging. Performance standards for hazmat packagings smaller than 118 gallons have been adopted in 49CFR178. Packagings for materials that are classified as toxic-by-inhalation must comply with the performance standards by October 1, 1993, and packagings for all other classes of hazardous materials covered must comply by October 1, 1996. For packages containing bulk (in excess of 188 gallons) quantities of materials that are extremely toxic by inhalation, there currently are no performance requirements. This paper discusses a Hazmat Packaging Performance Evaluation (HPPE) project to look at the subset of bulk packagings that are larger than 2000 gallons. The objectives of this project are the evaluate current hazmat specification packagings and develop supporting documentation for determining performance requirements for packagings in excess of 2000 gallons that transport hazardous materials that have been classified as extremely toxic by inhalation (METBI)

Sustainable Materials Management: Non-Hazardous Materials and Waste Management Hierarchy

Science.gov (United States)

EPA developed the non-hazardous materials and waste management hierarchy in recognition that no single waste management approach is suitable for managing all materials and waste streams in all circumstances.

A living foundry for Synthetic Biological Materials: A synthetic biology roadmap to new advanced materials

Directory of Open Access Journals (Sweden)

Rosalind A. Le Feuvre

2018-06-01

Full Text Available Society is on the cusp of harnessing recent advances in synthetic biology to discover new bio-based products and routes to their affordable and sustainable manufacture. This is no more evident than in the discovery and manufacture of Synthetic Biological Materials, where synthetic biology has the capacity to usher in a new Materials from Biology era that will revolutionise the discovery and manufacture of innovative synthetic biological materials. These will encompass novel, smart, functionalised and hybrid materials for diverse applications whose discovery and routes to bio-production will be stimulated by the fusion of new technologies positioned across physical, digital and biological spheres. This article, which developed from an international workshop held in Manchester, United Kingdom, in 2017 [1], sets out to identify opportunities in the new materials from biology era. It considers requirements, early understanding and foresight of the challenges faced in delivering a Discovery to Manufacturing Pipeline for synthetic biological materials using synthetic biology approaches. This challenge spans the complete production cycle from intelligent and predictive design, fabrication, evaluation and production of synthetic biological materials to new ways of bringing these products to market. Pathway opportunities are identified that will help foster expertise sharing and infrastructure development to accelerate the delivery of a new generation of synthetic biological materials and the leveraging of existing investments in synthetic biology and advanced materials research to achieve this goal. Keywords: Synthetic biology, Materials, Biological materials, Biomaterials, Advanced materials

Biological hazards of radioactivity and the biological consequences of radionuclide emissions from routine operation of nuclear power reactors

International Nuclear Information System (INIS)

Stendig-Lindberg, G.

1978-01-01

The biological hazards of radioactivity and the biological consequences of radionuclide emissions from the routine operation of nuclear power reactors are reviewed. ICRP and Scandinavian recommendations for the limitation of annual radiation doses are presented. The contribution of environmental conditions to radiation hazard is also discussed. It is concluded that a review of the justification of nuclear power is urgently needed. (H.K.)

Technology assessment of solar-energy systems. Materials resource and hazardous materials impacts of solar deployment

Science.gov (United States)

Schiffman, Y. M.; Tahami, J. E.

1982-04-01

The materials-resource and hazardous-materials impacts were determined by examining the type and quantity of materials used in the manufacture, construction, installation, operation and maintenance of solar systems. The materials requirements were compared with US materials supply and demand data to determine if potential problems exist in terms of future availability of domestic supply and increased dependence on foreign sources of supply. Hazardous materials were evaluated in terms of public and occupational health hazards and explosive and fire hazards. It is concluded that: although large amounts of materials would be required, the US had sufficient industrial capacity to produce those materials; (2) postulated growth in solar technology deployment during the period 1995-2000 could cause some production shortfalls in the steel and copper industry; the U.S. could increase its import reliance for certain materials such as silver, iron ore, and copper; however, shifts to other materials such as aluminum and polyvinylchloride could alleviate some of these problems.

An optimization model for transportation of hazardous materials

International Nuclear Information System (INIS)

Seyed-Hosseini, M.; Kheirkhah, A. S.

2005-01-01

In this paper, the optimal routing problem for transportation of hazardous materials is studied. Routing for the purpose of reducing the risk of transportation of hazardous materials has been studied and formulated by many researcher and several routing models have been presented up to now. These models can be classified into the categories: the models for routing a single movement and the models for routing multiple movements. In this paper, according to the current rules and regulations of road transportations of hazardous materials in Iran, a routing problem is designed. In this problem, the routs for several independent movements are simultaneously determined. To examine the model, the problem the transportations of two different dangerous materials in the road network of Mazandaran province in the north of Iran is formulated and solved by applying Integer programming model

Potential biological hazard of importance for HACCP plans in fresh fish processing

Directory of Open Access Journals (Sweden)

Baltić Milan Ž.

2009-01-01

Full Text Available The Hazard Analysis and Critical Control Point (HACCP system is scientifically based and focused on problem prevention in order to assure the produced food products are safe to consume. Prerequisite programs such as GMP (Good Manufacturing Practices, GHP (Good Hygienic Practices are an essential foundation for the development and implementation of successful HACCP plans. One of the preliminary tasks in the development of HACCP plan is to conduct a hazard analysis. The process of conducting a hazard analysis involves two stages. The first is hazard identification and the second stage is the HACCP team decision which potential hazards must be addressed in the HACCP plan. By definition, the HACCP concept covers all types of potential food safety hazards: biological, chemical and physical, whether they are naturally occurring in the food, contributed by the environment or generated by a mistake in the manufacturing process. In raw fish processing, potential significant biological hazards which are reasonably likely to cause illness of humans are parasites (Trematodae, Nematodae, Cestodae, bacteria (Salmonella, E. coli, Vibrio parahemolyticus, Vibrio vulnificus, Listeria monocytogenes, Clostridium botulinum, Staphyloccocus aureus, viruses (Norwalk virus, Entero virusesi, Hepatitis A, Rotovirus and bio-toxins. Upon completion of hazard analysis, any measure(s that are used to control the hazard(s should be described.

A living foundry for Synthetic Biological Materials: A synthetic biology roadmap to new advanced materials.

Science.gov (United States)

Le Feuvre, Rosalind A; Scrutton, Nigel S

2018-06-01

Society is on the cusp of harnessing recent advances in synthetic biology to discover new bio-based products and routes to their affordable and sustainable manufacture. This is no more evident than in the discovery and manufacture of Synthetic Biological Materials , where synthetic biology has the capacity to usher in a new Materials from Biology era that will revolutionise the discovery and manufacture of innovative synthetic biological materials. These will encompass novel, smart, functionalised and hybrid materials for diverse applications whose discovery and routes to bio-production will be stimulated by the fusion of new technologies positioned across physical, digital and biological spheres. This article, which developed from an international workshop held in Manchester, United Kingdom, in 2017 [1], sets out to identify opportunities in the new materials from biology era. It considers requirements, early understanding and foresight of the challenges faced in delivering a Discovery to Manufacturing Pipeline for synthetic biological materials using synthetic biology approaches. This challenge spans the complete production cycle from intelligent and predictive design, fabrication, evaluation and production of synthetic biological materials to new ways of bringing these products to market. Pathway opportunities are identified that will help foster expertise sharing and infrastructure development to accelerate the delivery of a new generation of synthetic biological materials and the leveraging of existing investments in synthetic biology and advanced materials research to achieve this goal.

Investigating the presence of hazardous materials in buildings

International Nuclear Information System (INIS)

Gustitus, D.A.; Blaisdell, P.M.

1996-01-01

Environmental hazards in buildings can be found in the air, on exposed surfaces, or hidden in roofs, walls, and systems. They can exist in buildings in solid, liquid, and gaseous states. A sound methodology for investigating the presence of environmental hazards in buildings should include several components. The first step in planning an investigation of environmental hazards in buildings is to ascertain why the investigation is to be performed. Research should be performed to review available documentation on the building. Next, a visual inspection of the building should be performed to identify and document existing conditions, and all suspect materials containing environmental hazards. Lastly, samples of suspect materials should be collected for testing. It is important to sample appropriate materials, based on the information obtained during the previous steps of the investigation. It is also important to collect the samples using standard procedures. Pollutants of concern include asbestos, lead, PCBs, and radon

Hazardous-materials-management system: a guide for local emergency managers

International Nuclear Information System (INIS)

Lee, M.T.; Roe, P.G.

1981-07-01

An increase in the manufacture, storage, and transportation of hazardous materials is occurring across the nation. Local jurisdictions have realized that they have the responsibility to assure a reasonable level of safety to their community members and visitors alike. Such a responsibility can be met by developing methods of preventing hazardous materials incidents; enforcing laws related to transporting and storing hazardous materials; the initiating of an appropriate first response, and activating available resources of government agencies and commercial organizations that deal with containment and cleanup. This manual has been written to help in the development of a total Hazardous Material Management System. The manual describes one approach but allows for variations as may be appropriate for the specific jurisdiction

Integrative Chemical-Biological Read-Across Approach for Chemical Hazard Classification

Science.gov (United States)

Low, Yen; Sedykh, Alexander; Fourches, Denis; Golbraikh, Alexander; Whelan, Maurice; Rusyn, Ivan; Tropsha, Alexander

2013-01-01

Traditional read-across approaches typically rely on the chemical similarity principle to predict chemical toxicity; however, the accuracy of such predictions is often inadequate due to the underlying complex mechanisms of toxicity. Here we report on the development of a hazard classification and visualization method that draws upon both chemical structural similarity and comparisons of biological responses to chemicals measured in multiple short-term assays (”biological” similarity). The Chemical-Biological Read-Across (CBRA) approach infers each compound's toxicity from those of both chemical and biological analogs whose similarities are determined by the Tanimoto coefficient. Classification accuracy of CBRA was compared to that of classical RA and other methods using chemical descriptors alone, or in combination with biological data. Different types of adverse effects (hepatotoxicity, hepatocarcinogenicity, mutagenicity, and acute lethality) were classified using several biological data types (gene expression profiling and cytotoxicity screening). CBRA-based hazard classification exhibited consistently high external classification accuracy and applicability to diverse chemicals. Transparency of the CBRA approach is aided by the use of radial plots that show the relative contribution of analogous chemical and biological neighbors. Identification of both chemical and biological features that give rise to the high accuracy of CBRA-based toxicity prediction facilitates mechanistic interpretation of the models. PMID:23848138

49 CFR 173.33 - Hazardous materials in cargo tank motor vehicles.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hazardous materials in cargo tank motor vehicles... Transportation § 173.33 Hazardous materials in cargo tank motor vehicles. (a) General requirements. (1) No person may offer or accept a hazardous material for transportation in a cargo tank motor vehicle except as...

Preventing method and device for underground permeation of hazardous material

International Nuclear Information System (INIS)

Funabashi, Kiyomi; Kurokawa, Hideaki; Fukazawa, Tetsuo; Yamazaki, Tadashi.

1996-01-01

In a method of preventing hazardous materials from permeating into ground by burying adsorbing materials underground, a plurality of adsorbing layers are laminated being spaced apart from each other, the concentration of the hazardous materials between each of the adsorbent layers is measured. When the concentration reaches a predetermined value, the adsorbent layers are regenerated. A suppression means for preventing hazardous materials from permeating into the ground are formed by an upper adsorbent layer and a lower adsorbent layer, and a means for measuring the concentration of hazardous materials passing through the upper adsorbent layer and a means for charging and discharging regenerated liquid are disposed. When it is detected that the poisonous materials can not be eliminated, the poisonous materials are already permeated to the adsorbent layer, and they start to inflow into underground water. In order to prevent it, an adsorbent layer is additionally disposed at the lower side of the place of detection to eliminate the poisonous materials completely thereby enabling to prevent poisonous materials from permeating into underground for a long period of time. (T.M.)

Instrumentation for Detecting Hazardous Materials.

Science.gov (United States)

1980-06-01

equipment a detector for monitoring radioactivity . A portable device for detecting the presence of hazardous mate- rials should also be included in the...Acrylonitrile 2 Natural Gas/LNG 2 211 ----- Material Name (Cont’d.) Number of Times Listed Radioactive Materials 2 Fertilizers 1 Cellulose Nitrate 1 Acrolein...Birnbaum, and Curtis Fincher, L "Fluorescence Determination of the Atmospheric Polutant NO2 in Impact of Lasers in Spectroscopy, Vol. 49 of Proceed

EFSA BIOHAZ Panel (EFSA Panel on Biological Hazards), 2013. Scientific Opinion on the public health hazards to be covered by inspection of meat (bovine animals)

DEFF Research Database (Denmark)

Hald, Tine; Baggesen, Dorte Lau

for the farm-to-chilled carcass continuum using a risk-based approach was proposed. Key elements of the system are risk-categorisation of slaughter animals for high-priority biological hazards based on improved food chain information, as well as risk-categorisation of slaughterhouses according......A risk ranking process identified Salmonella spp. and pathogenic verocytotoxin-producing Escherichia coli (VTEC) as current high-priority biological hazards for meat inspection of bovine animals. As these hazards are not detected by traditional meat inspection, a meat safety assurance system...... to their capability to control those hazards. Omission of palpation and incision during post-mortem inspection for animals subjected to routine slaughter may decrease spreading and cross-contamination with the high-priority biological hazards. For chemical hazards, dioxins and dioxin-like polychlorinated biphenyls...

GGVS. Ordinance on road transport of hazardous materials, including the European agreement on international road transport of hazardous materials (ADR), in their wording. Annexes A and B. Ordinances regarding exceptions from GGVS and from the ordinance on rail transport of hazardous materials, GGVE. Reasons. Selected guidelines. List of materials. 6. rev. and enlarged ed.

International Nuclear Information System (INIS)

Ridder, K.

1990-01-01

The brochure contains the following texts: (1) Ordinance on road transport of hazardous materials (GGVS), including the European agreement on international road transport of hazardous materials (ADR), as of 1990: Skeleton ordinance, annexes A and B, reasons given for the first version, and for the first amendment in 1988, execution guidelines - RS 002 (guidelines for executing the ordinance on road transport of hazardous materials, with catalogue of penalties), guidelines for drawing up written instructions for the event of accidents - RS 006, guiding principles for the training of vehicle conductors; (2) ordinance regarding exceptions from the ordinance on road transport of hazardous materials; (3) ordinance regarding exceptions from the ordinance on rail transport of hazardous materials; (4) selected guidelines: Technical guidelines TR IBC K 001, TRS 003, TRS 004, TRS 005, TRS 006; (5) listing of materials and objects governed by the ordinance on hazardous materials transport; (6) catalogue of penalties relative to road transport of hazardous materials. (orig./HP) [de

Transportation of hazardous materials (hazmat a literature survey

Directory of Open Access Journals (Sweden)

Zafer YILMAZ

2016-02-01

Full Text Available ransportation has a great role in logistics. Many researchers have studied on transportation and vehicle routing problems. Transportation of hazardous materials (hazmat is a special subject for logistics. Causalities due to the accidents caused by trucks carrying hazardous materials will be intolerable. Many researchers have studied on risk assessment of hazmat transportation to find ways for reducing hazardous material transportation risks. Some researchers have studied routing of hazmat trucks. The emergency response models and network design problems for hazmat transportation were also studied by some researchers. The transportation of hazmats can also be classified according to the mode of transport. Mainly roads are used for hazmat transportation but some shipments are intermodal. There has been a great amount of effort spent to find convenient ways for hazmat transportation. In this study, a literature survey for the articles about hazmat transportation is prepared. After pointing out the importance of hazmat transportation by the example of US hazmat transportation data, the studies on hazmat transportation since 2005 have been examined. Totally 88 articles are classified as risk, routing, routing and scheduling, emergency response, network design and accident analysis. What can be studied in future researches is pointed out.Keywords: Hazardous materials, Network design, Transportation, Routing, Risk assessment

Auditors of safety in hazardous materials transportation

International Nuclear Information System (INIS)

Manas Lahoz, J.L.

1993-01-01

The author describes the methodology for safety auditory and control, prevention, risks of hazardous materials transport through ship, airplane, rail, etc. In this way, The author presents the classification of damage materials transport, characteristic damage and different transport methods

Hanford Site radioactive hazardous materials packaging directory

International Nuclear Information System (INIS)

McCarthy, T.L.

1995-12-01

The Hanford Site Radioactive Hazardous Materials Packaging Directory (RHMPD) provides information concerning packagings owned or routinely leased by Westinghouse Hanford Company (WHC) for offsite shipments or onsite transfers of hazardous materials. Specific information is provided for selected packagings including the following: general description; approval documents/specifications (Certificates of Compliance and Safety Analysis Reports for Packaging); technical information (drawing numbers and dimensions); approved contents; areas of operation; and general information. Packaging Operations ampersand Development (PO ampersand D) maintains the RHMPD and may be contacted for additional information or assistance in obtaining referenced documentation or assistance concerning packaging selection, availability, and usage

Hanford Site radioactive hazardous materials packaging directory

Energy Technology Data Exchange (ETDEWEB)

McCarthy, T.L.

1995-12-01

The Hanford Site Radioactive Hazardous Materials Packaging Directory (RHMPD) provides information concerning packagings owned or routinely leased by Westinghouse Hanford Company (WHC) for offsite shipments or onsite transfers of hazardous materials. Specific information is provided for selected packagings including the following: general description; approval documents/specifications (Certificates of Compliance and Safety Analysis Reports for Packaging); technical information (drawing numbers and dimensions); approved contents; areas of operation; and general information. Packaging Operations & Development (PO&D) maintains the RHMPD and may be contacted for additional information or assistance in obtaining referenced documentation or assistance concerning packaging selection, availability, and usage.

Risk methodologies for offsite hazardous materials

International Nuclear Information System (INIS)

Kot, C.A.; Eichler, T.V.; Wiedermann, A.H.

1983-01-01

A number of suggestions have been advanced in recent years concerning the risks posed to nuclear power plants by offsite hazardous materials relative to (1) the regulatory approach including considerations of minimum and safe standoff distances, exclusion distances, site acceptance ceilings and floors, screening distances and screening probabilities, plant design, etc., and (2) the analysis and evaluation procedures such as material screening criteria, plant vulnerability, standarized physical models, etc. An evaluation of current analyses and approaches indicates that this complex problem, variety of approaches, and safety concerns may be better accommodated by developing criteria and treatments along the lines of a so-called conditional risk approach. Specifically, the probability (P) of some ultimate consequence (C) occurring from an accident (A) involving hazardous materials is given as P(C) = P(C/A) x P(A). Assuming that the plant to accident site standoff distance is the fundamental independent variable of the risk methodology, certain conditional risk designations and conditions can be made and are presented

77 FR 60935 - Hazardous Materials: Minor Editorial Corrections and Clarifications (RRR)

Science.gov (United States)

2012-10-05

... flammable cryogenic liquid is not received by the consignee within 20 days from the date of shipment.... * * * * * Container ship * * * * * * * * Hazardous material means a substance or material that the Secretary of... transportation law (49 U.S.C. 5103). The term includes hazardous substances, hazardous wastes, marine pollutants...

Quality assurance for packaging of radioactive and hazardous materials

International Nuclear Information System (INIS)

Gustafson, L.D.

1986-01-01

The Department of Energy (DOE) has required for many years that quality assurance programs be established and implemented for the packaging of radioactive and hazardous materials. This paper identifies various requirement principles and related actions involved in establishing effective quality assurance for packaging of radioactive and hazardous materials. A primary purpose of these quality assurance program activities is to provide assurance that the packaging and transportation of hazardous materials, which includes radioactive and fissile materials, are in conformance with appropriate governmental regulations. Applicable regulations include those issued by the Nuclear Regulatory Commission (NRC), the Department of Transportation (DOT), and the Environmental Protection Agency (EPA). DOE Order 5700.6A establishes that quality assurance requirements are to be applied in accordance with national consensus standards where suitable ones are available. In the nuclear area, ANSI/ASME NQA-1 is the preferred standard

IAEA biological reference materials

International Nuclear Information System (INIS)

Parr, R.M.; Schelenz, R.; Ballestra, S.

1988-01-01

The Analytical Quality Control Services programme of the IAEA encompasses a wide variety of intercomparisons and reference materials. This paper reviews only those aspects of the subject having to do with biological reference materials. The 1988 programme foresees 13 new intercomparison exercises, one for major, minor and trace elements, five for radionuclides, and seven for stable isotopes. Twenty-two natural matrix biological reference materials are available: twelve for major, minor and trace elements, six for radionuclides, and four for chlorinated hydrocarbons. Seven new intercomparisons and reference materials are in preparation or under active consideration. Guidelines on the correct use of reference materials are being prepared for publication in 1989 in consultation with other major international producers and users of biological reference materials. The IAEA database on available reference materials is being updated and expanded in scope, and a new publication is planned for 1989. (orig.)

Biologically Hazardous Agents at Work and Efforts to Protect Workers' Health: A Review of Recent Reports

Directory of Open Access Journals (Sweden)

Kyung-Taek Rim

2014-06-01

Full Text Available Because information on biological agents in the workplace is lacking, biological hazard analyses at the workplace to securely recognize the harmful factors with biological basis are desperately needed. This review concentrates on literatures published after 2010 that attempted to detect biological hazards to humans, especially workers, and the efforts to protect them against these factors. It is important to improve the current understanding of the health hazards caused by biological factors at the workplace. In addition, this review briefly describes these factors and provides some examples of their adverse health effects. It also reviews risk assessments, protection with personal protective equipment, prevention with training of workers, regulations, as well as vaccinations.

37 CFR 1.801 - Biological material.

Science.gov (United States)

2010-07-01

... 37 Patents, Trademarks, and Copyrights 1 2010-07-01 2010-07-01 false Biological material. 1.801... Biological Material § 1.801 Biological material. For the purposes of these regulations pertaining to the deposit of biological material for purposes of patents for inventions under 35 U.S.C. 101, the term...

Program in change: shipment of hazardous materials at the INEL

International Nuclear Information System (INIS)

Reed, L.L.

1984-01-01

Positive measures such as education, control, and auditing ability should be incorporated into each hazardous material shipping program to assure compliance with regulations and the safe movement of hazardous materials. This paper discusses these and other pertinent components of a shipping program. 3 references

Environmentally sound management of hazardous waste and hazardous recyclable materials

International Nuclear Information System (INIS)

Smyth, T.

2002-01-01

Environmentally sound management or ESM has been defined under the Basel Convention as 'taking all practicable steps to ensure that hazardous wastes and other wastes are managed in a manner which will protect human health and the environment against the adverse effects which may result from such wastes'. An initiative is underway to develop and implement a Canadian Environmentally Sound Management (ESM) regime for both hazardous wastes and hazardous recyclable materials. This ESM regime aims to assure equivalent minimum environmental protection across Canada while respecting regional differences. Cooperation and coordination between the federal government, provinces and territories is essential to the development and implementation of ESM systems since waste management is a shared jurisdiction in Canada. Federally, CEPA 1999 provides an opportunity to improve Environment Canada's ability to ensure that all exports and imports are managed in an environmentally sound manner. CEPA 1999 enabled Environment Canada to establish criteria for environmentally sound management (ESM) that can be applied by importers and exporters in seeking to ensure that wastes and recyclable materials they import or export will be treated in an environmentally sound manner. The ESM regime would include the development of ESM principles, criteria and guidelines relevant to Canada and a procedure for evaluating ESM. It would be developed in full consultation with stakeholders. The timeline for the development and implementation of the ESM regime is anticipated by about 2006. (author)

Natural radioactivity and radiological hazards of building materials in Xianyang, China

International Nuclear Information System (INIS)

Lu Xinwei; Yang Guang; Ren Chunhui

2012-01-01

Common building materials collected from Xianyang, China were analyzed for the natural radioactivity of 226 Ra, 232 Th and 40 K using γ-ray spectroscopy. The average activity concentration of 226 Ra, 232 Th and 40 K in the studied building materials ranges from 13.4 to 69.9, 13.1–99.1 and 124.7–915.1 Bq kg −1 , respectively. The measured activity concentrations for these radionuclides were compared with the reported data of other countries and with the worldwide average activity of soil. To assess the radiation hazard of the natural radioactivity in all samples to the people, the radium equivalent activity, external hazard index, internal hazard index, indoor absorbed dose rate and total annual effective dose were estimated. The radium equivalent activities of the studied samples are below the internationally accepted values. The external hazard index and internal hazard index of all analyzed building materials are less than unity. The mean values of indoor absorbed dose rate for all building materials except for lime are higher than the world population-weighted average of 84 nGy h −1 and the total annual effective dose values of building materials are lower than 1 mSv y −1 except for some cyan brick samples. The study shows the measured building materials do not pose significant source of radiation hazard and are safe for use in the construction of dwellings. - Highlights: ► Natural radioactivity in building materials was determined by gamma ray spectrometry. ► The radiological hazard of studied building materials is within the recommended safety limit. ► Most of the studied building materials do not pose significant radiation risk to residents.

Unify a hazardous materials/waste program

International Nuclear Information System (INIS)

Carson, H.T.

1988-01-01

Efficiently managing a hazardous materials/waste program in a multi-facility, multi-product corporation is a major challenge. This paper describes several methods to help unify a program and gain maximum efficiency of manpower and to minimize risk

Hazardous Materials Management and Emergency Response (HAMMER)

Data.gov (United States)

Federal Laboratory Consortium — The Volpentest Hazardous Materials Management and Emergency Response (HAMMER) Federal Training Center is a safety and emergency response training center that offers...

Biological treatment of concentrated hazardous, toxic, andradionuclide mixed wastes without dilution

Energy Technology Data Exchange (ETDEWEB)

Stringfellow, William T.; Komada, Tatsuyuki; Chang, Li-Yang

2004-06-15

Approximately 10 percent of all radioactive wastes produced in the U. S. are mixed with hazardous or toxic chemicals and therefore can not be placed in secure land disposal facilities. Mixed wastes containing hazardous organic chemicals are often incinerated, but volatile radioactive elements are released directly into the biosphere. Some mixed wastes do not currently have any identified disposal option and are stored locally awaiting new developments. Biological treatment has been proposed as a potentially safer alternative to incineration for the treatment of hazardous organic mixed wastes, since biological treatment would not release volatile radioisotopes and the residual low-level radioactive waste would no longer be restricted from land disposal. Prior studies have shown that toxicity associated with acetonitrile is a significant limiting factor for the application of biotreatment to mixed wastes and excessive dilution was required to avoid inhibition of biological treatment. In this study, we demonstrate that a novel reactor configuration, where the concentrated toxic waste is drip-fed into a complete-mix bioreactor containing a pre-concentrated active microbial population, can be used to treat a surrogate acetonitrile mixed waste stream without excessive dilution. Using a drip-feed bioreactor, we were able to treat a 90,000 mg/L acetonitrile solution to less than 0.1 mg/L final concentration using a dilution factor of only 3.4. It was determined that the acetonitrile degradation reaction was inhibited at a pH above 7.2 and that the reactor could be modeled using conventional kinetic and mass balance approaches. Using a drip-feed reactor configuration addresses a major limiting factor (toxic inhibition) for the biological treatment of toxic, hazardous, or radioactive mixed wastes and suggests that drip-feed bioreactors could be used to treat other concentrated toxic waste streams, such as chemical warfare materiel.

Multiscale Biological Materials

DEFF Research Database (Denmark)

Frølich, Simon

of multiscale biological systems have been investigated and new research methods for automated Rietveld refinement and diffraction scattering computed tomography developed. The composite nature of biological materials was investigated at the atomic scale by looking at the consequences of interactions between...

Risk management of onsite transportation of hazardous materials

International Nuclear Information System (INIS)

Wang, O.S.; Field, J.G.

1992-10-01

The US Department of Energy's (DOE) Hanford Site has recently undergone a significant change in its mission. The focus of site-wide operations has been shifted from production to environmental restoration. As a result, there is a significant increase in quantities of the radioactive wastes and other hazardous materials to be packaged and transported onsite. In response to the elevated transportation activities, the operations and engineering contractor for the Hanford Site, Westinghouse Hanford Company (Westinghouse Hanford), is proposing an integrated risk assessment methodology and risk management strategy to further enhance the safe operations of the onsite packaging and transportation activities involving radioactive and other hazardous materials. This paper summarizes Westinghouse Hanford's proposed risk assessment and risk management methodology for onsite transportation of hazardous materials. The proposed Westinghouse Hanford risk assessment and management methodology for onsite packaging and transportation has three integral parts: risk assessment, risk acceptance criteria, and risk minimization process. The purposes are to ensure that the risk for each ongoing transportation activity is acceptable, and to further reduce the overall risk for current and future onsite transportation activities

Regional risk associated with the transport of hazardous materials

OpenAIRE

Nardini, L.; Aparicio, L.; Bandoni, A.; Tonelli, S. M.

2003-01-01

An increasing concern over the level of risk associated with hazardous materials transportation has led international efforts to focus on risk assessment at regional level. Following this trend, the aim of this work is to review the latest procedures for analysing the regional risks resulting from hazardous materials transportation by means of road and rail. In particular, two methodologies are reviewed and discussed, a method recently developed at Swiss Federal Institute of Technology [1] an...

Toward a federal/state/local partnership in hazardous materials transportation safety

International Nuclear Information System (INIS)

1982-09-01

In recognition of the federal government's responsibility for initiating a national strategy for hazardous materials transportation safety, the Materials Transportation Bureau (MTB) prepared an internal strategy paper for creating a federal/state/local partnership in hazardous materials transportation safety in August 1981. The paper outlined the scope of the hazardous materials transportation problem and established MTB's approach for creating an intergovernmental partnership for its resolution. This paper represents an update and refinement of the original plan, and is designed to chart the direction of the emerging federal/state/local relationship. The cornerstone of the plan remains the establishment of a single national set of safety regulations. It is on achievement of this objective that MTB's plan for development of enforcement, training, and emergency response capabilities at all levels of government is based. Chapter I introduces the problem with a desription of the economic importance of hazardous materials and discusses its implications for public safety. Chapter II defines the appropriate role for each level of government in the areas of rulemaking, enforcement, emergency response, and education. Chapter III demonstrates the need for uniform national safety standards and describes the economic and safety benefits of this approach. Chapter IV contains a detailed description of MTB's program for developing a successful intergovernmental partnership in hazardous materials transportation safety

Environmental risk analysis of hazardous material rail transportation

Energy Technology Data Exchange (ETDEWEB)

Saat, Mohd Rapik, E-mail: mohdsaat@illinois.edu [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States); Werth, Charles J.; Schaeffer, David [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States); Yoon, Hongkyu [Sandia National Laboratories, Albuquerque, NM 87123 (United States); Barkan, Christopher P.L. [Department of Civil and Environmental Engineering, University of Illinois at Urbana-Champaign, 1243 Newmark Civil Engineering Laboratory, 205 North Mathews Avenue, Urbana, IL 61801 (United States)

2014-01-15

Highlights: • Comprehensive, nationwide risk assessment of hazardous material rail transportation. • Application of a novel environmental (i.e. soil and groundwater) consequence model. • Cleanup cost and total shipment distance are the most significant risk factors. • Annual risk varies from $20,000 to $560,000 for different products. • Provides information on the risk cost associated with specific product shipments. -- Abstract: An important aspect of railroad environmental risk management involves tank car transportation of hazardous materials. This paper describes a quantitative, environmental risk analysis of rail transportation of a group of light, non-aqueous-phase liquid (LNAPL) chemicals commonly transported by rail in North America. The Hazardous Materials Transportation Environmental Consequence Model (HMTECM) was used in conjunction with a geographic information system (GIS) analysis of environmental characteristics to develop probabilistic estimates of exposure to different spill scenarios along the North American rail network. The risk analysis incorporated the estimated clean-up cost developed using the HMTECM, route-specific probability distributions of soil type and depth to groundwater, annual traffic volume, railcar accident rate, and tank car safety features, to estimate the nationwide annual risk of transporting each product. The annual risk per car-mile (car-km) and per ton-mile (ton-km) was also calculated to enable comparison between chemicals and to provide information on the risk cost associated with shipments of these products. The analysis and the methodology provide a quantitative approach that will enable more effective management of the environmental risk of transporting hazardous materials.

Environmental risk analysis of hazardous material rail transportation

International Nuclear Information System (INIS)

Saat, Mohd Rapik; Werth, Charles J.; Schaeffer, David; Yoon, Hongkyu; Barkan, Christopher P.L.

2014-01-01

Highlights: • Comprehensive, nationwide risk assessment of hazardous material rail transportation. • Application of a novel environmental (i.e. soil and groundwater) consequence model. • Cleanup cost and total shipment distance are the most significant risk factors. • Annual risk varies from $20,000 to $560,000 for different products. • Provides information on the risk cost associated with specific product shipments. -- Abstract: An important aspect of railroad environmental risk management involves tank car transportation of hazardous materials. This paper describes a quantitative, environmental risk analysis of rail transportation of a group of light, non-aqueous-phase liquid (LNAPL) chemicals commonly transported by rail in North America. The Hazardous Materials Transportation Environmental Consequence Model (HMTECM) was used in conjunction with a geographic information system (GIS) analysis of environmental characteristics to develop probabilistic estimates of exposure to different spill scenarios along the North American rail network. The risk analysis incorporated the estimated clean-up cost developed using the HMTECM, route-specific probability distributions of soil type and depth to groundwater, annual traffic volume, railcar accident rate, and tank car safety features, to estimate the nationwide annual risk of transporting each product. The annual risk per car-mile (car-km) and per ton-mile (ton-km) was also calculated to enable comparison between chemicals and to provide information on the risk cost associated with shipments of these products. The analysis and the methodology provide a quantitative approach that will enable more effective management of the environmental risk of transporting hazardous materials

A suggested approach to the selection of chemical and biological protective clothing--meeting industry and emergency response needs for protection against a variety of hazards.

Science.gov (United States)

Stull, Jeffrey O

2004-01-01

The paper describes the development of a comprehensive decision logic for selection and use of biological and chemical protective clothing (BCPC). The decision logic recognizes the separate areas of BCPC use among emergency, biological, and chemical hazards. The proposed decision logic provides a system for type classifying BCPC in terms of its compliance with existing standards (for emergency applications), the overall clothing integrity, and the material barrier performance. Type classification is offered for garments, gloves, footwear, and eye/face protection devices. On the basis of multiple, but simply designed flowcharts, the type of BCPC appropriate for specific biological and chemical hazards can be selected. The decision logic also provides supplemental considerations for choosing appropriate BCPC features.

Technologies to remediate hazardous waste sites

International Nuclear Information System (INIS)

Falco, J.W.

1990-03-01

Technologies to remediate hazardous wastes must be matched with the properties of the hazardous materials to be treated, the environment in which the wastes are imbedded, and the desired extent of remediation. Many promising technologies are being developed, including biological treatment, immobilization techniques, and in situ methods. Many of these new technologies are being applied to remediate sites. The management and disposal of hazardous wastes is changing because of federal and state legislation as well as public concern. Future waste management systems will emphasize the substitution of alternatives for the use of hazardous materials and process waste recycling. Onsite treatment will also become more frequently adopted. 5 refs., 7 figs

Hazardous materials sensing: An electrical metamaterial approach

Energy Technology Data Exchange (ETDEWEB)

Rawat, Vaishali; Kitture, Rohini [Department of Applied Physics, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India); Kumari, Dimple [Department of Applied Chemistry, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India); Rajesh, Harsh [Society for Applied Microwave Electronics Engineering and Research (SAMEER), IIT-Bombay Campus, Powai, Mumbai (India); Banerjee, Shaibal [Department of Applied Chemistry, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India); Kale, S.N., E-mail: sangeetakale2004@gmail.com [Department of Applied Physics, Defence Institute of Advanced Technology (DIAT), Girinagar, Pune 411025 (India)

2016-10-01

Metamaterials are recently emerging materials exhibiting amazing properties such as extremely miniaturized antennas, waveguides, optical couplers, multiplexers and filters. Such structures also respond to the variation in their ambient conditions when exposed to toxic and hazardous materials, which are especially hazardous to human health. Through this manuscript, we document our studies on three different high energy materials; namely 2- bromo-2nitropropane-1,3-diol (BNP), bis (1,3-diazido prop-2-yl) malonate (AM) and bis (1,3-diazido prop-2-yl) glutarate (AG). A Complementary Split Ring Resonator has been fabricated at resonant frequency of 4.48 GHz using copper on FR4 substrate. The energetic materials were exposed to the sensor and results were monitored using Vector Network Analyzer. The volume of liquids was varied from 0.5 µL to 3 µL. Prominent and explicit shifts in the transmission resonant frequency and amplitude was seen as a signature of each energetic material. The signatures were not only sensitive to the specific toxic group in the material but also to the volume of the liquid subjected to this sensor. The results are correlated with the simulation results, basic chemistry of the materials and permittivity measurements. The ultra-fast reversibility and repeatability, with good sensitivity and specificity of these devices project their applications in sensitive locations, particularly to combat for human security and health issues.

e-Biologics: Fabrication of Sustainable Electronics with "Green" Biological Materials.

Science.gov (United States)

Lovley, Derek R

2017-06-27

The growing ubiquity of electronic devices is increasingly consuming substantial energy and rare resources for materials fabrication, as well as creating expansive volumes of toxic waste. This is not sustainable. Electronic biological materials (e-biologics) that are produced with microbes, or designed with microbial components as the guide for synthesis, are a potential green solution. Some e-biologics can be fabricated from renewable feedstocks with relatively low energy inputs, often while avoiding the harsh chemicals used for synthesizing more traditional electronic materials. Several are completely free of toxic components, can be readily recycled, and offer unique features not found in traditional electronic materials in terms of size, performance, and opportunities for diverse functionalization. An appropriate investment in the concerted multidisciplinary collaborative research required to identify and characterize e-biologics and to engineer materials and devices based on e-biologics could be rewarded with a new "green age" of sustainable electronic materials and devices. Copyright © 2017 Lovley.

49 CFR 172.202 - Description of hazardous material on shipping papers.

Science.gov (United States)

2010-10-01

... papers. 172.202 Section 172.202 Transportation Other Regulations Relating to Transportation PIPELINE AND... INFORMATION, TRAINING REQUIREMENTS, AND SECURITY PLANS Shipping Papers § 172.202 Description of hazardous material on shipping papers. (a) The shipping description of a hazardous material on the shipping paper...

Screening tests for hazard classification of complex waste materials – Selection of methods

International Nuclear Information System (INIS)

Weltens, R.; Vanermen, G.; Tirez, K.; Robbens, J.; Deprez, K.; Michiels, L.

2012-01-01

In this study we describe the development of an alternative methodology for hazard characterization of waste materials. Such an alternative methodology for hazard assessment of complex waste materials is urgently needed, because the lack of a validated instrument leads to arbitrary hazard classification of such complex waste materials. False classification can lead to human and environmental health risks and also has important financial consequences for the waste owner. The Hazardous Waste Directive (HWD) describes the methodology for hazard classification of waste materials. For mirror entries the HWD classification is based upon the hazardous properties (H1–15) of the waste which can be assessed from the hazardous properties of individual identified waste compounds or – if not all compounds are identified – from test results of hazard assessment tests performed on the waste material itself. For the latter the HWD recommends toxicity tests that were initially designed for risk assessment of chemicals in consumer products (pharmaceuticals, cosmetics, biocides, food, etc.). These tests (often using mammals) are not designed nor suitable for the hazard characterization of waste materials. With the present study we want to contribute to the development of an alternative and transparent test strategy for hazard assessment of complex wastes that is in line with the HWD principles for waste classification. It is necessary to cope with this important shortcoming in hazardous waste classification and to demonstrate that alternative methods are available that can be used for hazard assessment of waste materials. Next, by describing the pros and cons of the available methods, and by identifying the needs for additional or further development of test methods, we hope to stimulate research efforts and development in this direction. In this paper we describe promising techniques and argument on the test selection for the pilot study that we have performed on different

Comparative biological hazards of chemical pollutants and radiation

International Nuclear Information System (INIS)

Mukherjee, R.N.

1978-01-01

Chemical pollutants from conventional energy and industrial sources released to the environment presumably pose a hazard to man's health and environmental resources. Insufficient knowledge of their detailed mechanisms of interaction with the biological systems seems to provide the greatest drawback in current attempts for realistic assessment of the health risks of chemical pollutants in the short and long terms. Nevertheless, their detrimental health consequences are becoming more and more apparent as a result of recent epidemiological surveys of workers in conventional energy installations and of the chronically exposed general public. So far nuclear power has succeeded in achieving a remarkable health safety record. In view of its projected expansion, research on biological effects of low-level radiation and radionuclides should continue to re-evaluate the health safety consequences. However, a projection from past experiences together with continued efforts to improvements of health safety aspects seem to justify an expectation that the proposed expansions in the nuclear power programme should not have an unfavourable impact on the environment. The potential hazards and challenges from the associated radiation in man's environment have proved manageable. More attention now needs to be paid urgently to safeguard human health and environment against the chemical pollutants

Comparative biological hazards of chemical pollutants and radiation

Energy Technology Data Exchange (ETDEWEB)

Mukherjee, R N [International Atomic Energy Agency, Vienna (Austria). Div. of Life Sciences

1978-06-01

Chemical pollutants from conventional energy and industrial sources released to the environment presumably pose a hazard to man's health and environmental resources. Insufficient knowledge of their detailed mechanisms of interaction with the biological systems seems to provide the greatest drawback in current attempts for realistic assessment of the health risks of chemical pollutants in the short and long terms. Nevertheless, their detrimental health consequences are becoming more and more apparent as a result of recent epidemiological surveys of workers in conventional energy installations and of the chronically exposed general public. So far nuclear power has succeeded in achieving a remarkable health safety record. In view of its projected expansion, research on biological effects of low-level radiation and radionuclides should continue to re-evaluate the health safety consequences. However, a projection from past experiences together with continued efforts to improvements of health safety aspects seem to justify an expectation that the proposed expansions in the nuclear power programme should not have an unfavourable impact on the environment. The potential hazards and challenges from the associated radiation in man's environment have proved manageable. More attention now needs to be paid urgently to safeguard human health and environment against the chemical pollutants.

Biological treatment of concentrated hazardous, toxic, and radionuclide mixed wastes without dilution

International Nuclear Information System (INIS)

Stringfellow, William T.; Komada, Tatsuyuki; Chang, Li-Yang

2004-01-01

Approximately 10 percent of all radioactive wastes produced in the U. S. are mixed with hazardous or toxic chemicals and therefore can not be placed in secure land disposal facilities. Mixed wastes containing hazardous organic chemicals are often incinerated, but volatile radioactive elements are released directly into the biosphere. Some mixed wastes do not currently have any identified disposal option and are stored locally awaiting new developments. Biological treatment has been proposed as a potentially safer alternative to incineration for the treatment of hazardous organic mixed wastes, since biological treatment would not release volatile radioisotopes and the residual low-level radioactive waste would no longer be restricted from land disposal. Prior studies have shown that toxicity associated with acetonitrile is a significant limiting factor for the application of biotreatment to mixed wastes and excessive dilution was required to avoid inhibition of biological treatment. In this study, we demonstrate that a novel reactor configuration, where the concentrated toxic waste is drip-fed into a complete-mix bioreactor containing a pre-concentrated active microbial population, can be used to treat a surrogate acetonitrile mixed waste stream without excessive dilution. Using a drip-feed bioreactor, we were able to treat a 90,000 mg/L acetonitrile solution to less than 0.1 mg/L final concentration using a dilution factor of only 3.4. It was determined that the acetonitrile degradation reaction was inhibited at a pH above 7.2 and that the reactor could be modeled using conventional kinetic and mass balance approaches. Using a drip-feed reactor configuration addresses a major limiting factor (toxic inhibition) for the biological treatment of toxic, hazardous, or radioactive mixed wastes and suggests that drip-feed bioreactors could be used to treat other concentrated toxic waste streams, such as chemical warfare materiel

Hazardous materials management and compliance training

International Nuclear Information System (INIS)

Dalton, T.F.

1991-01-01

OSHA training for hazardous waste site workers is required by the Superfund Amendments and Reauthorization Act of 1986 (SARA). In December 1986, a series of regulations was promulgated by OSHA on an interim basis calling for the training of workers engaged in hazardous waste operations. Subsequent to these interim regulations, final rules were promulgated and these final rules on hazardous waste operations and emergency response became effective on March 6, 1990. OSHA has conducted hearings on the accreditation of training programs. OSHA would like to follow the accreditation process under the AHERA regulations for asbestos, in which the model plan for accreditation of asbestos abatement training was included in Section 206 of Title 11 of the Toxic Substance Control Act (TSCA). OSHA proposed on January 26, 1990, to perform the accreditation of training programs for hazardous waste operations and that proposal suggested that they follow the model plan similar to the one used for AHERA. They did not propose to accredited training programs for workers engaged in emergency response. These new regulations pose a significant problem to the various contractors and emergency responders who deal with hazardous materials spill response, cleanup and site remediation since these programs have expanded so quickly that many people are not familiar with what particular segment of the training they are required to have and whether or not programs that have yet to be accredited are satisfactory for this type of training. Title III of SARA stipulates a training program for first responders which includes local emergency response organizations such as firemen and policemen. The purpose of this paper is to discuss the needs of workers at hazardous waste site remediation projects and workers who are dealing with hazardous substances, spill response and cleanup

Hazardous materials transportation and emergency response programs

International Nuclear Information System (INIS)

Joy, D.S.; Fore, C.S.

1983-01-01

This presentation consists of the following visual aids; (1) detailed routing capabilities of truck, rail, barge; (2) legislative data base for hazardous materials; and (3) emergency response of accident site Eddyville, Kentucky (airports in vicinity of Eddyville, KY)

Recommendations for sampling for prevention of hazards in civil defense. On analytics of chemical, biological and radioactive contaminations. 2. ed.; Empfehlungen fuer die Probenahme zur Gefahrenabwehr im Bevoelkerungsschutz. Zur Analytik von chemischen, biologischen und radioaktiven Kontaminationen

Energy Technology Data Exchange (ETDEWEB)

Bachmann, Udo; Derakshani, Nahid; Drobig, Matthias; Koenig, Mario; Mentfewitz, Joachim; Prast, Hartmut; Uelpenich, Gerhard; Vidmayer, Marc; Wilbert, Stefan; Wolf, Manfred

2016-07-01

The recommendations for sampling for prevention of hazards in civil defense (analytics of chemical, biological and radioactive contaminations) cover the following topics: Requirements for sampling, description of the materials (chemical, biological and radioactive contaminated materials), decontamination, sample transport and protocol documents.

Automated accountability of hazardous materials at AlliedSignal Inc., Kansas City Division

International Nuclear Information System (INIS)

Depew, P.L.

1993-12-01

The Department of Energy's (DOE) Kansas City Plant (KCP), currently operated by AlliedSignal Inc. has developed a comprehensive Hazardous Material Information System (HMIS). The purpose of this system is to provide a practical and automated method to collect, analyze and distribute hazardous material information to DOE, KCP associates, and regulatory agencies. The drivers of the HMIS are compliance with OSHA Hazard Communications, SARA reporting, pollution prevention, waste minimization, control and tracking of hazards, and emergency response. This report provides a discussion of this system

Evaluation of Hazardous Material Management Safety in the Chemical Laboratory in BATAN

International Nuclear Information System (INIS)

Nur-Rahmah-Hidayati

2005-01-01

The management safety of the hazardous material (B3) in the chemical laboratory of BATAN was evaluated. The evaluation is necessary to be done because B3 is often used together with radioactive materials in the laboratory, but the attention to the safety aspect of B3 is not paid sufficiently in spite of its big potential hazard. The potential hazard generated from the nature of B3 could be flammable, explosive, oxidative, corrosive and poisonous. The handling of B3 could be conducted by enforcing the labelling and classification in the usage and disposal processes. Some observations of the chemical laboratory of BATAN show that the management safety of hazardous material in compliance with the government regulation no. 74 year 2001 has not been dully conducted. The management safety of B3 could be improved by, designating one who has adequate skill in hazardous material safety specially as the B3 safety officer, providing the Material Safety Data Sheet that is updated periodically to use in the laboratory and storage room, updating periodically the inventory of B3, performing training in work safety periodically, and monitoring the ventilation system intensively in laboratory and storage room. (author)

EFSA Panel on Biological Hazards (BIOHAZ); Scientific Opinion on Composting on-farm of dead poultry

DEFF Research Database (Denmark)

Hald, Tine

EFSA’s Scientific Panel on Biological Hazards (BIOHAZ) was asked for a scientific opinion on two alternative methods for processing Category (Cat) 2 Animal By-Products (ABP). The material to be treated consists of poultry manure, straw and dead-on-farm poultry; this implies that the animals died...... due to a disease, which in most cases was not properly diagnosed. The proposed processes are composting methods to be used on-farm. The first method is a continuous open system where composting is done under roof in piles separated by wooden partition walls. The piles are processed without enforced...

Integrated risk reduction framework to improve railway hazardous materials transportation safety.

Science.gov (United States)

Liu, Xiang; Saat, M Rapik; Barkan, Christopher P L

2013-09-15

Rail transportation plays a critical role to safely and efficiently transport hazardous materials. A number of strategies have been implemented or are being developed to reduce the risk of hazardous materials release from train accidents. Each of these risk reduction strategies has its safety benefit and corresponding implementation cost. However, the cost effectiveness of the integration of different risk reduction strategies is not well understood. Meanwhile, there has been growing interest in the U.S. rail industry and government to best allocate resources for improving hazardous materials transportation safety. This paper presents an optimization model that considers the combination of two types of risk reduction strategies, broken rail prevention and tank car safety design enhancement. A Pareto-optimality technique is used to maximize risk reduction at a given level of investment. The framework presented in this paper can be adapted to address a broader set of risk reduction strategies and is intended to assist decision makers for local, regional and system-wide risk management of rail hazardous materials transportation. Copyright © 2013 Elsevier B.V. All rights reserved.

Sandia National Laboratories, California Hazardous Materials Management Program annual report.

Energy Technology Data Exchange (ETDEWEB)

Brynildson, Mark E.

2011-02-01

The annual program report provides detailed information about all aspects of the Sandia National Laboratories, California (SNL/CA) Hazardous Materials Management Program. It functions as supporting documentation to the SNL/CA Environmental Management System Program Manual. This program annual report describes the activities undertaken during the calender past year, and activities planned in future years to implement the Hazardous Materials Management Program, one of six programs that supports environmental management at SNL/CA.

Airborne biological hazards and urban transport infrastructure: current challenges and future directions.

Science.gov (United States)

Nasir, Zaheer Ahmad; Campos, Luiza Cintra; Christie, Nicola; Colbeck, Ian

2016-08-01

Exposure to airborne biological hazards in an ever expanding urban transport infrastructure and highly diverse mobile population is of growing concern, in terms of both public health and biosecurity. The existing policies and practices on design, construction and operation of these infrastructures may have severe implications for airborne disease transmission, particularly, in the event of a pandemic or intentional release of biological of agents. This paper reviews existing knowledge on airborne disease transmission in different modes of transport, highlights the factors enhancing the vulnerability of transport infrastructures to airborne disease transmission, discusses the potential protection measures and identifies the research gaps in order to build a bioresilient transport infrastructure. The unification of security and public health research, inclusion of public health security concepts at the design and planning phase, and a holistic system approach involving all the stakeholders over the life cycle of transport infrastructure hold the key to mitigate the challenges posed by biological hazards in the twenty-first century transport infrastructure.

Hazard identification and risk assessment for biologics targeting the immune system.

Science.gov (United States)

Weir, Andrea B

2008-01-01

Biologic pharmaceuticals include a variety of products, such as monoclonal antibodies, fusion proteins and cytokines. Products in those classes include immunomodulatory biologics, which are intended to enhance or diminish the activity of the immune system. Immunomodulatory biologics have been approved by the U.S. FDA for a variety of indications, including cancer and inflammatory conditions. Prior to gaining approval for marketing, sponsoring companies for all types of products must demonstrate a product's safety in toxicology studies conducted in animals and show safety and efficacy in clinical trials conducted in patients. The overall goal of toxicology studies, which applies to immunomodulatory and other product types, is to identify the hazards that products pose to humans. Because biologics are generally highly selective for specific targets (receptors/epitopes), conducting toxicology studies in animal models with the target is essential. Such animals are referred to as pharmacologically relevant. Endpoints routinely included in toxicology studies, such as hematology, organ weight and histopathology, can be used to assess the effect of a product on the structure of the immune system. Additionally, specialized endpoints, such as immunophenotyping and immune function tests, can be used to define effects of immunomodulatory products on the immune system. Following hazard identification, risks posed to patients are assessed and managed. Risks can be managed through clinical trial design and risk communication, a practice that applies to immunomodulatory and other product types. Examples of risk management in clinical trial design include establishing a safe starting dose, defining the appropriate patient population and establishing appropriate patient monitoring. Risk communication starts during clinical trials and continues after product approval. A combination of hazard identification, risk assessment and risk management allows for drug development to proceed

Hazardous materials management and control program at Oak Ridge National Laboratory - environmental protection

International Nuclear Information System (INIS)

Eisenhower, B.M.; Oakes, T.W.

1982-01-01

In the Federal Register of May 19, 1980, the US Environmental Protection Agency promulgated final hazardous waste regulations according to the Resource Conservation and Recovery Act (RCRA) of 1976. The major substantive portions of these regulations went into effect on November 19, 1980, and established a federal program to provide comprehensive regulation of hazardous waste from its generation to its disposal. In an effort to comply with these regulations, a Hazardous Materials Management and Control Program was established at Oak Ridge National Laboratory. The program is administered by two Hazardous Materials Coordinators, who together with various support groups, ensure that all hazardous materials and wastes are handled in such a manner that all personnel, the general public, and the environment are adequately protected

Natural and technologic hazardous material releases during and after natural disasters: a review.

Science.gov (United States)

Young, Stacy; Balluz, Lina; Malilay, Josephine

2004-04-25

Natural disasters may be powerful and prominent mechanisms of direct and indirect hazardous material (hazmat) releases. Hazardous materials that are released as the result of a technologic malfunction precipitated by a natural event are referred to as natural-technologic or na-tech events. Na-tech events pose unique environmental and human hazards. Disaster-associated hazardous material releases are of concern, given increases in population density and accelerating industrial development in areas subject to natural disasters. These trends increase the probability of catastrophic future disasters and the potential for mass human exposure to hazardous materials released during disasters. This systematic review summarizes direct and indirect disaster-associated releases, as well as environmental contamination and adverse human health effects that have resulted from natural disaster-related hazmat incidents. Thorough examination of historic disaster-related hazmat releases can be used to identify future threats and improve mitigation and prevention efforts.

Transportation of hazardous materials in Iran: A strategic approach for decreasing accidents

Directory of Open Access Journals (Sweden)

S. Ghazinoory

2008-06-01

Full Text Available .“Hazardous materials” refer to those substances that seriously endanger human lives and/or the environment. The transportation of these materials will be inevitable in the increasingly industrialized economy of Iran. Nonetheless, numerous deadly accidents caused by the movement of these materials necessitate the design and implementation of preventive plans on several levels. This article looks into the present condition of transportation of hazardous materials in Iran and the resulting accidents. Optimal condition for the general transportation system of hazardous materials is delineated with due focus on transportation risk as the main parameter. Strategies for reaching the optimal condition are laid out and the impacts of these strategies on the reduction of accidents are analyzed.

A five-year history of hazardous materials incidents in Chester County, PA

International Nuclear Information System (INIS)

Shorten, C.V.; McNamara, J.

1993-01-01

The Emergency Planning and Community Right-to-Know Act (EPCRA) of 1986 established Local Emergency Planning Committees (LEPCs) to oversee emergency response planning at the community level. In Pennsylvania, each county was assigned its own LEPC, and Chester County held its first LEPC meeting on October 15, 1987. From the data of that meeting through September 1992, 300 hazardous materials incidents have been reported. The majority of these incidents were met with fire department response, but several warranted response by hazardous materials teams. This report presents an analysis of the database of reported hazardous materials incidents in Chester County, including chemical identification, amount released, type of response, location, and trends. Over 235 of the reported spills were either gasoline, diesel fuel, home heating oil, or kerosene, often in five to 50 gallon amounts from transportation accidents. A number of extremely hazardous substance (EHS) incidents were reported, however, including sulfuric acid, chlorine, ammonia, phosphorus, formaldehyde, bromine, methyl mercaptan, and hydrofluoric acid. The most commonly released EHS's were ammonia and chlorine. The number of hazardous materials incidents reported in Chester County increased from only 14 in 1988 to 95 in 1991, with 67 in 1992 through September. This dramatic increase is attributable to both increased reporting and an increased number of incidents. This database clearly indicates both the success of EPCRA reporting system and the magnitude of hazardous materials incidents in this part of Pennsylvania

49 CFR 176.99 - Permit requirements for certain hazardous materials.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Permit requirements for certain hazardous materials. 176.99 Section 176.99 Transportation Other Regulations Relating to Transportation PIPELINE AND... CARRIAGE BY VESSEL Special Requirements for Barges § 176.99 Permit requirements for certain hazardous...

Storage and transport of hazardous materials

International Nuclear Information System (INIS)

Jaeger, P.; Haferkamp, K.

1986-01-01

The attempt has been made to characterise the present risk scenario, and to set out approaches or methods for remedy and risk control. For this purpose, a retrospective analysis has been made of accidents, damage and consequential damage that occurred in the past either during storage of hazardous materials, or during road transport. A risk-benefit model facilitates assessment of accident frequency. The history of accidents during storage or transport allows assessment of the dangerousness of various materials. Another important aspect discussed is the property and behaviour of containers used for storage or transport. (DG) [de

Evaluation of methods to compare consequences from hazardous materials transportation accidents

International Nuclear Information System (INIS)

Rhoads, R.E.; Franklin, A.L.; Lavender, J.C.

1986-10-01

This report presents the results of a project to develop a framework for making meaningful comparisons of the consequences from transportation accidents involving hazardous materials. The project was conducted in two phases. In Phase I, methods that could potentially be used to develop the consequence comparisons for hazardous material transportation accidents were identified and reviewed. Potential improvements were identified and an evaluation of the improved methods was performed. Based on this evaluation, several methods were selected for detailed evaluation in Phase II of the project. The methods selected were location-dependent scenarios, figure of merit and risk assessment. This evaluation included application of the methods to a sample problem which compares the consequences of four representative hazardous materials - chlorine, propane, spent nuclear fuel and class A explosives. These materials were selected because they represented a broad class of hazardous material properties and consequence mechanisms. The sample case aplication relied extensively on consequence calculations performed in previous transportation risk assessment studies. A consultant was employed to assist in developing consequence models for explosives. The results of the detailed evaluation of the three consequence comparison methods indicates that methods are available to perform technically defensible comparisons of the consequences from a wide variety of hazardous materials. Location-dependent scenario and risk assessment methods are available now and the figure of merit method could be developed with additional effort. All of the methods require substantial effort to implement. Methods that would require substantially less effort were identified in the preliminary evaluation, but questions of technical accuracy preclude their application on a scale. These methods may have application to specific cases, however

Perceived safety of transporting hazardous materials

International Nuclear Information System (INIS)

Reese, R.T.; Shepherd, E.W.

1981-01-01

A framework for relating the variables involved in the public perception of hazardous materials transportation was presented. The framework consisted of a conditional mathematical equation in which perceived safety was described by six basic terms (technical feasibility, political palatability, social responsibility, utility assessment, media interpretation, and familiarity as a function of time). The resulting framework provides the technologist with an initial formulation to better understand public perception

Anal Sphincter Augmentation Using Biological Material.

Science.gov (United States)

Alam, Nasra N; Narang, Sunil K; Köckerling, Ferdinand; Daniels, Ian R; Smart, Neil J

2015-01-01

The aim of this review is to provide an overview of the use of biological materials in the augmentation of the anal sphincter either as part of an overlapping sphincter repair (OSR) or anal bulking procedure. A systematic search of PubMed was conducted using the search terms "anal bulking agents," "anal sphincter repair," or "overlapping sphincter repair." Five studies using biological material as part of an overlapping sphincter repair (OSR) or as an anal bulking agent were identified. 122 patients underwent anal bulking with a biological material. Anorectal physiology was conducted in 27 patients and demonstrated deterioration in maximum resting pressure, and no significant change in maximum squeeze increment. Quality of life scores (QoLs) demonstrated improvements at 6 weeks and 6 months, but this had deteriorated at 12 months of follow up. Biological material was used in 23 patients to carry out an anal encirclement procedure. Improvements in QoLs were observed in patients undergoing OSR as well as anal encirclement using biological material. Incontinence episodes decreased to an average of one per week from 8 to 10 preoperatively. Sphincter encirclement with biological material has demonstrated improvements in continence and QoLs in the short term compared to traditional repair alone. Long-term studies are necessary to determine if this effect is sustained. As an anal bulking agent the benefits are short-term.

GIS risk analysis of hazardous materials transport

International Nuclear Information System (INIS)

Anders, C.; Olsten, J.

1991-01-01

The Geographic Information System (GIS) was used to assess the risks and vulnerability of transporting hazardous materials and wastes (such as gasoline, explosives, poisons, etc) on the Arizona highway system. This paper discusses the methodology that was utilized, and the application of GIS systems to risk analysis problems

Feasibility study--computerized application of the hazardous material regulations

International Nuclear Information System (INIS)

Ferrada, J.J.; Green, V.M.; Rawl, R.R.

1992-09-01

The feasibility of developing a full expert system for transportation and packaging of hazardous and radioactive materials was initiated within the framework of three subtasks: (1) analysis of commercial packages related to regulation scanning, (2) analysis of computer languages to develop the expert system, and (3) development of expert system prototypes. The strategy to develop the latter subtask was to first,develop modules to capture the knowledge of different areas of transportation and packaging and second, to analyze the feasibility of appending these different modules in one final full package. The individual modules development contemplated one prototype for transporting and packaging of radioactive material and another for transporting hazardous chemical materials. In the event that it is not feasible to link these two packages, the modules can always be used as stand-alone tools, or linked as a single package with some restrictions in their applicability. The work done during this fiscal year has focused on developing a prototype for transporting radioactive materials

78 FR 60726 - Hazardous Materials Regulations: Penalty Guidelines

Science.gov (United States)

2013-10-02

... new categories: Offeror Requirements for specific hazardous materials: Oxygen Generators and Batteries... protecting public health, welfare, safety, and our environment.'' Executive Order 13610 further instructs... the human environment. When developing potential regulatory requirements, PHMSA evaluates those...

Hazardous materials management using a Cradle-to-Grave Tracking and Information System (CGTIS)

Energy Technology Data Exchange (ETDEWEB)

Kjeldgaard, E.; Fish, J.; Campbell, D.; Freshour, N.; Hammond, B.; Bray, O. [Sandia National Labs., Albuquerque, NM (United States); Hollingsworth, M. [Ogden Environmental & Energy Services Co., Inc., Albuquerque, NM (United States)

1995-03-01

Hazardous materials management includes interactions among materials, personnel, facilities, hazards, and processes of various groups within a DOE site`s environmental, safety & health (ES&H) and line organizations. Although each group is charged with addressing a particular aspect of these properties and interactions, the information it requires must be gathered into a coherent set of common data for accurate and consistent hazardous material management and regulatory reporting. It is these common data requirements which the Cradle-to-Grave Tracking and Information System (CGTIS) is designed to satisfy. CGTIS collects information at the point at which a process begins or a material enters a facility, and maintains that information, for hazards management and regulatory reporting, throughout the entire life-cycle by providing direct on-line links to a site`s multitude of data bases to bring information together into one common data model.

Hazardous materials management using a Cradle-to-Grave Tracking and Information System (CGTIS)

International Nuclear Information System (INIS)

Kjeldgaard, E.; Fish, J.; Campbell, D.; Freshour, N.; Hammond, B.; Bray, O.; Hollingsworth, M.

1995-03-01

Hazardous materials management includes interactions among materials, personnel, facilities, hazards, and processes of various groups within a DOE site's environmental, safety ampersand health (ES ampersand H) and line organizations. Although each group is charged with addressing a particular aspect of these properties and interactions, the information it requires must be gathered into a coherent set of common data for accurate and consistent hazardous material management and regulatory reporting. It is these common data requirements which the Cradle-to-Grave Tracking and Information System (CGTIS) is designed to satisfy. CGTIS collects information at the point at which a process begins or a material enters a facility, and maintains that information, for hazards management and regulatory reporting, throughout the entire life-cycle by providing direct on-line links to a site's multitude of data bases to bring information together into one common data model

Transport and Reactivity of Decontaminants to Provide Hazard Mitigation of Chemical Warfare Agents from Materials

Science.gov (United States)

2016-06-01

2013 4. TITLE AND SUBTITLE Transport and Reactivity of Decontaminants to Provide Hazard Mitigation of Chemical Warfare Agents from Materials 5a...directions for future decontamination formulation approaches. 15. SUBJECT TERMS GD HD Decontamination Hazard mitigation VX Chemical warfare agent... DECONTAMINANTS TO PROVIDE HAZARD MITIGATION OF CHEMICAL WARFARE AGENTS FROM MATERIALS 1. INTRODUCTION Decontamination of materials is the

Chemical hazards from decontamination solutions in low level waste

International Nuclear Information System (INIS)

Leventhal, L.; Miller, A.; Turney, J.; Naughton, M.; IMPELL Corp., Walnut Creek, CA; Electric Power Research Inst., Palo Alto, CA)

1985-01-01

Recent regulations are focussing more attention on the non-radioactive matrix materials associated with radioactive wastes. Decontamination of operating facilities is becoming a more significant source of low-level waste. This study reviewed the chemical and biological hazards of over 50 decontamination processes. Seventeen of the most prominent hard and soft decontamination processes were examined in detail. The chemical and biological hazards of these seventeen are presented in this paper. These hazards influence the choice of radwaste processing and packaging operations and methods. Federal, state and local regulations further impact on operations and waste disposal. Hazards to personnel, in plant and off-site, resulting from the decontamination cycle are evaluated. 1 fig., 5 tabs

Hazardous Materials Verification and Limited Characterization Report on Sodium and Caustic Residuals in Materials and Fuel Complex Facilities MFC-799/799A

Energy Technology Data Exchange (ETDEWEB)

Gary Mecham

2010-08-01

This report is a companion to the Facilities Condition and Hazard Assessment for Materials and Fuel Complex Sodium Processing Facilities MFC-799/799A and Nuclear Calibration Laboratory MFC-770C (referred to as the Facilities Condition and Hazards Assessment). This report specifically responds to the requirement of Section 9.2, Item 6, of the Facilities Condition and Hazards Assessment to provide an updated assessment and verification of the residual hazardous materials remaining in the Sodium Processing Facilities processing system. The hazardous materials of concern are sodium and sodium hydroxide (caustic). The information supplied in this report supports the end-point objectives identified in the Transition Plan for Multiple Facilities at the Materials and Fuels Complex, Advanced Test Reactor, Central Facilities Area, and Power Burst Facility, as well as the deactivation and decommissioning critical decision milestone 1, as specified in U.S. Department of Energy Guide 413.3-8, “Environmental Management Cleanup Projects.” Using a tailored approach and based on information obtained through a combination of process knowledge, emergency management hazardous assessment documentation, and visual inspection, this report provides sufficient detail regarding the quantity of hazardous materials for the purposes of facility transfer; it also provides that further characterization/verification of these materials is unnecessary.

Tulane/Xavier University Hazardous Materials in Aquatic Environments of the Mississippi River Basin. Quarterly progress report, January 1, 1995--March 31, 1995

International Nuclear Information System (INIS)

1995-01-01

This progress report covers activities for the period January 1 - March 31, 1995 on project concerning 'Hazardous Materials in Aquatic Environments of the Mississippi River Basin.' The following activities are each summarized by bullets denoting significant experiments/findings: biotic and abiotic studies on the biological fate, transport and ecotoxicity of toxic and hazardous waste in the Mississippi River Basin; assessment of mechanisms of metal-induced reproductive toxicity in quatic species as a biomarker of exposure; hazardous wastes in aquatic environments: biological uptake and metabolism studies; ecological sentinels of aquatic contamination in the lower Mississippi River system; bioremediation of selected contaminants in aquatic environments of the Mississippi River Basin; a sensitive rapid on-sit immunoassay for heavy metal contamination; pore-level flow, transport, agglomeration and reaction kinetics of microorganism; biomarkers of exposure and ecotoxicity in the Mississippi River Basin; natural and active chemical remediation of toxic metals, organics and radionuclides in the aquatic environment; expert geographical information systems for assessing hazardous wastes in aquatic environments; enhancement of environmental education; and a number of just initiated projects including fate and transport of contaminants in aquatic environments; photocatalytic remediation; radionuclide fate and modeling from Chernobyl

77 FR 24885 - Hazardous Materials; Miscellaneous Amendments (RRR)

Science.gov (United States)

2012-04-26

... special provisions, clarify the lab pack requirements for temperature-controlled materials, and revise the... in Dewar flasks. Clarify the lab pack provisions in Sec. 173.12 pertaining to temperature-controlled... shipping names, hazard classes, packing groups, special provisions, packaging authorizations, air transport...

Calculation of Airborne Radioactivity Hazard from Machining Volume-Activated Materials

International Nuclear Information System (INIS)

E.T. Marshall; S.O. Schwahn

1997-01-01

When evaluating a task involving the machining of volume-activated materials, accelerator health physicists must consider more than the surface contamination levels of the equipment and containment of loose shavings, dust or filings. Machining operations such as sawing, routing, welding, and grinding conducted on volume-activated material may pose a significant airborne radioactivity hazard to the worker. This paper presents a computer spreadsheet notebook that conservatively estimates the airborne radioactivity levels generated during machining operations performed on volume-activated materials. By knowing (1) the size and type of materials, (2) the dose rate at a given distances, and (3) limited process knowledge, the Derived Air Concentration (DAC) fraction can be estimated. This tool is flexible, taking into consideration that the process knowledge available for the different materials varies. It addresses the two most common geometries: thick plane and circular cylinder. Once the DAC fraction has been estimated, controls can be implemented to mitigate the hazard to the worker

Calculation of airborne radioactivity hazard from machining volume-activated materials

International Nuclear Information System (INIS)

Marshall, E.T.; Schwahn, S.O.

1996-10-01

When evaluating a task involving the machining of volume-activated materials, accelerator health physicists must consider more than the surface contamination levels of the equipment and containment of loose shavings, dust or filings. Machining operations such as sawing, routing, welding, and grinding conducted on volume-activated material may pose a significant airborne radioactivity hazard to the worker. This paper presents a computer spreadsheet notebook that conservatively estimates the airborne radioactivity levels generated during machining operations performed on volume-activated materials. By knowing (1) the size and type of materials, (2) the dose rate at a given distances, and (3) limited process knowledge, the Derived Air Concentration (DAC) fraction can be estimated. This tool is flexible, taking into consideration that the process knowledge available for the different materials varies. It addresses the two most common geometries: thick plane and circular cylinder. Once the DAC fraction has been estimated, controls can be implemented to mitigate the hazard to the worker

Project plan, Hazardous Materials Management and Emergency Response Training Center: Project 95L-EWT-100

International Nuclear Information System (INIS)

Borgeson, M.E.

1994-01-01

The Hazardous Materials Management and Emergency Response (HAMMER) Training Center will provide for classroom lectures and hands-on practical training in realistic situations for workers and emergency responders who are tasked with handling and cleanup of toxic substances. The primary objective of the HAMMER project is to provide hands-on training and classroom facilities for hazardous material workers and emergency responders. This project will also contribute towards complying with the planning and training provisions of recent legislation. In March 1989 Title 29 Code of Federal Regulations Occupational Safety and Health Administration 1910 Rules and National Fire Protection Association Standard 472 defined professional requirements for responders to hazardous materials incidents. Two general types of training are addressed for hazardous materials: training for hazardous waste site workers and managers, and training for emergency response organizations

78 FR 16044 - Hazardous Materials Packaging-Composite Cylinder Standards; Public Meeting

Science.gov (United States)

2013-03-13

... Toughiry, Engineering and Research Division, Office of Hazardous Materials Safety, Pipeline and Hazardous... the HMR, ISO 11119 Parts-1, -2 and -3, contain design, construction and testing requirements that are.../permits-approvals/special-permits . II. Public Meeting Topics During this public meeting, PHMSA will...

Preparedness of hazardous materials emergencies in railyards: Guidance for railroads and adjacent communities

Energy Technology Data Exchange (ETDEWEB)

1991-09-01

Railroads are a key part of the distribution system for hazardous materials and, thus, much hazardous material passes through railyards en route to intermediate or final consumers. While the vast majority of these materials are shipped without incident, both the number of shipments and the nature of the materials themselves dictate that railyards and surrounding communities be prepared to respond quickly and effectively to emergencies. This report contains information on 11 emergency preparedness functions and 150 guidance recommendations.

Radioactivity and associated radiation hazards in ceramic raw materials and end products.

Science.gov (United States)

Viruthagiri, G; Rajamannan, B; Suresh Jawahar, K

2013-12-01

Studies have been planned to obtain activity and associated radiation hazards in ceramic raw materials (quartz, feldspar, clay, zircon, kaolin, grog, alumina bauxite, baddeleyite, masse, dolomite and red mud) and end products (ceramic brick, glazed ceramic wall and floor tiles) as the activity concentrations of uranium, thorium and potassium vary from material to material. The primordial radionuclides in ceramic raw materials and end products are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the activity level in these materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the activity concentration of (226)Ra, (232)Th and (40)K in ceramic raw materials and end products. The activity of these materials has been measured using a gamma-ray spectrometry, which contains an NaI(Tl) detector connected to multichannel analyser (MCA). Radium equivalent activity, alpha-gamma indices and radiation hazard indices associated with the natural radionuclides are calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant international legislation and guidance and compared with the results of similar studies reported in different countries. The results suggest that the use of ceramic end product samples examined in the construction of dwellings, workplace and industrial buildings is unlikely to give rise to any significant radiation exposure to the occupants.

Radioactivity and associated radiation hazards in ceramic raw materials and end products

International Nuclear Information System (INIS)

Viruthagiri, G.; Rajamannan, B.; Suresh Jawahar, K.

2013-01-01

Studies have been planned to obtain activity and associated radiation hazards in ceramic raw materials (quartz, feldspar, clay, zircon, kaolin, grog, alumina bauxite, baddeleyite, masse, dolomite and red mud) and end products (ceramic brick, glazed ceramic wall and floor tiles) as the activity concentrations of uranium, thorium and potassium vary from material to material. The primordial radionuclides in ceramic raw materials and end products are one of the sources of radiation hazard in dwellings made of these materials. By the determination of the activity level in these materials, the indoor radiological hazard to human health can be assessed. This is an important precautionary measure whenever the dose rate is found to be above the recommended limits. The aim of this work was to measure the activity concentration of 226 Ra, 232 Th and 40 K in ceramic raw materials and end products. The activity of these materials has been measured using a gamma-ray spectrometry, which contains an NaI(Tl) detector connected to multichannel analyser (MCA). Radium equivalent activity, alpha-gamma indices and radiation hazard indices associated with the natural radionuclides are calculated to assess the radiological aspects of the use of the ceramic end products as decorative or covering materials in construction sector. Results obtained were examined in the light of the relevant international legislation and guidance and compared with the results of similar studies reported in different countries. The results suggest that the use of ceramic end product samples examined in the construction of dwellings, workplace and industrial buildings is unlikely to give rise to any significant radiation exposure to the occupants. (authors)

Numerical investigation of debris materials prior to debris flow hazards using satellite images

Science.gov (United States)

Zhang, N.; Matsushima, T.

2018-05-01

The volume of debris flows occurred in mountainous areas is mainly affected by the volume of debris materials deposited at the valley bottom. Quantitative evaluation of debris materials prior to debris flow hazards is important to predict and prevent hazards. At midnight on 7th August 2010, two catastrophic debris flows were triggered by the torrential rain from two valleys in the northern part of Zhouqu City, NW China, resulting in 1765 fatalities and huge economic losses. In the present study, a depth-integrated particle method is adopted to simulate the debris materials, based on 2.5 m resolution satellite images. In the simulation scheme, the materials are modeled as dry granular solids, and they travel down from the slopes and are deposited at the valley bottom. The spatial distributions of the debris materials are investigated in terms of location, volume and thickness. Simulation results show good agreement with post-disaster satellite images and field observation data. Additionally, the effect of the spatial distributions of the debris materials on subsequent debris flows is also evaluated. It is found that the spatial distributions of the debris materials strongly influence affected area, runout distance and flow discharge. This study might be useful in hazard assessments prior to debris flow hazards by investigating diverse scenarios in which the debris materials are unknown.

Mission: Possible. Center of Excellence for Hazardous Materials Management

International Nuclear Information System (INIS)

Bartlett, W.T.; Prather-Stroud, W.

2006-01-01

The Center of Excellence for Hazardous Materials Management (CEHMM) was established in May 2004 as a nonprofit research organization. Its purpose is to develop a sustainable technical/scientific community located in Carlsbad, New Mexico, that interacts worldwide to find solutions to hazardous materials management issues. An important part of the mission is to achieve improved protection of worker safety, human health, and the environment. Carlsbad has a large technical community due to the presence of the Waste Isolation Pilot Plant (WIPP) and its many contractors and support organizations. These groups include the Carlsbad Environmental Monitoring and Research Center, Washington Group International, Los Alamos National Laboratory, and Sandia National Laboratories. These organizations form the basis of a unique knowledge community with strengths in many areas, such as geosciences, actinide chemistry, environmental monitoring, and waste transportation. CEHMM works cooperatively with these organizations and others to develop projects that will maintain this knowledge community beyond the projected closure date of WIPP. At present, there is an emphasis in bio-monitoring, air monitoring, hazardous materials educational programs, and endangered species remediation. CEHMM is also currently working with a group from the American Nuclear Society to help facilitate their conference scheduled for April 2006 in Carlsbad. CEHMM is growing rapidly and is looking forward to a diverse array of new projects. (authors)

Transport of hazardous materials in the Amazon area; Transporte de produtos perigosos na regiao Amazonica

Energy Technology Data Exchange (ETDEWEB)

Cunha, Wallace de Castro [FURNAS Centrais Eletricas S.A., Rio de Janeiro, RJ (Brazil); Fernandes, Elton; Nassi, Carlos David [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE)

2008-07-01

Amongst several exploratory sources of the subject 'hazardous materials transport', it is distinguished: 'the threat to the environment'. This paper presents an exploratory investigation of this subject line in the Amazon region. In view of the diversity of 'existing hazardous materials' and the raised dimension of the oil transport and its derivatives in this context, this paper focused in these products. Regarding to the geographic region, the approach was given to the State of Amazon, considering the amplitude of this State in the Amazon region and the availability of data. Therefore, this work explores and analyzes macro aspects inherent to the State of Amazon pertinent to the oil transport and its derivatives. In the macro context, it is observed the necessity of a higher control in the transport of hazardous materials in the region. The absence of registered data and the unfamiliarity on the risks related to the transport of hazardous materials by authorities and transporters indicate a relative absence of qualification in the region to deal with the monitoring of the transport of hazardous materials. So far, it is not possible up till now to make any evaluation of the environment threats of accidents with transport of hazardous materials in the Amazon region.(author)

Transport of hazardous materials in the Amazon area; Transporte de produtos perigosos na regiao Amazonica

Energy Technology Data Exchange (ETDEWEB)

Cunha, Wallace de Castro [FURNAS Centrais Eletricas S.A., Rio de Janeiro, RJ (Brazil); Fernandes, Elton; Nassi, Carlos David [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-Graduacao de Engenharia (COPPE)

2008-07-01

Amongst several exploratory sources of the subject 'hazardous materials transport', it is distinguished: 'the threat to the environment'. This paper presents an exploratory investigation of this subject line in the Amazon region. In view of the diversity of 'existing hazardous materials' and the raised dimension of the oil transport and its derivatives in this context, this paper focused in these products. Regarding to the geographic region, the approach was given to the State of Amazon, considering the amplitude of this State in the Amazon region and the availability of data. Therefore, this work explores and analyzes macro aspects inherent to the State of Amazon pertinent to the oil transport and its derivatives. In the macro context, it is observed the necessity of a higher control in the transport of hazardous materials in the region. The absence of registered data and the unfamiliarity on the risks related to the transport of hazardous materials by authorities and transporters indicate a relative absence of qualification in the region to deal with the monitoring of the transport of hazardous materials. So far, it is not possible up till now to make any evaluation of the environment threats of accidents with transport of hazardous materials in the Amazon region.(author)

NATO Advanced Research Workshop, 19-22 May 1997: Rapid Method for Monitoring the Environment for Biological Hazards

National Research Council Canada - National Science Library

1997-01-01

The NATO Advanced Research Workshop met for the purpose of bringing to light rapid methods for monitoring the environment for biological hazards such as biological warfare agents, naturally occurring...

75 FR 38168 - Hazardous Materials: International Regulations for the Safe Transport of Radioactive Material (TS...

Science.gov (United States)

2010-07-01

... may also provide contact information, such as a telephone number and/or e-mail address. PHMSA and the.... PHMSA-2010-0130 (Notice No.10-2)] Hazardous Materials: International Regulations for the Safe Transport... (IAEA) ``Regulations for the Safe Transport of Radioactive Material'' (TS-R-1), which is scheduled for...

Sandia National Laboratories, California Hazardous Materials Management Program annual report : February 2009.

Energy Technology Data Exchange (ETDEWEB)

Brynildson, Mark E.

2009-02-01

The annual program report provides detailed information about all aspects of the Sandia National Laboratories, California (SNL/CA) Hazardous Materials Management Program. It functions as supporting documentation to the SNL/CA Environmental anagement ystem Program Manual. This program annual report describes the activities undertaken during the past year, and activities planned in future years to implement the Hazardous Materials Management Program, one of six programs that supports environmental management at SNL/CA.

[Applications of synthetic biology in materials science].

Science.gov (United States)

Zhao, Tianxin; Zhong, Chao

2017-03-25

Materials are the basis for human being survival and social development. To keep abreast with the increasing needs from all aspects of human society, there are huge needs in the development of advanced materials as well as high-efficiency but low-cost manufacturing strategies that are both sustainable and tunable. Synthetic biology, a new engineering principle taking gene regulation and engineering design as the core, greatly promotes the development of life sciences. This discipline has also contributed to the development of material sciences and will continuously bring new ideas to future new material design. In this paper, we review recent advances in applications of synthetic biology in material sciences, with the focus on how synthetic biology could enable synthesis of new polymeric biomaterials and inorganic materials, phage display and directed evolution of proteins relevant to materials development, living functional materials, engineered bacteria-regulated artificial photosynthesis system as well as applications of gene circuits for material sciences.

Quality Assurance Program Plan for the Hazardous Materials Transportation and Packaging Program. Revision 1

Energy Technology Data Exchange (ETDEWEB)

Calihan, T.W. III; Votaw, E.F.

1995-05-01

This QAPP covers only the implementation accomplished through Level I and II manuals. It covers the quality affecting activities identified in USDOE orders (both HQ and Richland Operations Office), US DOT, US EPA, and NRC regulations, IAEA guidelines, and the WHC manuals. It covers activities related to hazardous materials transportation performed on and off the Hanford site under the jurisdictional authority of WHC. (Hazardous materials include radioactive, hazardous waste, and mixed waste.)

Quality Assurance Program Plan for the Hazardous Materials Transportation and Packaging Program. Revision 1

International Nuclear Information System (INIS)

Calihan, T.W. III; Votaw, E.F.

1995-01-01

This QAPP covers only the implementation accomplished through Level I and II manuals. It covers the quality affecting activities identified in USDOE orders (both HQ and Richland Operations Office), US DOT, US EPA, and NRC regulations, IAEA guidelines, and the WHC manuals. It covers activities related to hazardous materials transportation performed on and off the Hanford site under the jurisdictional authority of WHC. (Hazardous materials include radioactive, hazardous waste, and mixed waste.)

77 FR 39662 - Hazardous Materials; Reverse Logistics (RRR)

Science.gov (United States)

2012-07-05

... logistics providers estimate that up to 7% of an enterprise's gross sales are return costs. The third-party... logistic shipments for hazardous materials? III. Issues To Be Considered As previously noted, the purpose... documentation costs to develop and maintain risk assessments and operational procedures? If so, what is a fair...

Emergency response network design for hazardous materials transportation with uncertain demand

Directory of Open Access Journals (Sweden)

Kamran Shahanaghi

2012-10-01

Full Text Available Transportation of hazardous materials play an essential role on keeping a friendly environment. Every day, a substantial amount of hazardous materials (hazmats, such as flammable liquids and poisonous gases, need to be transferred prior to consumption or disposal. Such transportation may result in unsuitable events for people and environment. Emergency response network is designed for this reason where specialist responding teams resolve any issue as quickly as possible. This study proposes a new multi-objective model to locate emergency response centers for transporting the hazardous materials. Since many real-world applications are faced with uncertainty in input parameters, the proposed model of this paper also assumes that reference and demand to such centre is subject to uncertainty, where demand is fuzzy random. The resulted problem formulation is modelled as nonlinear non-convex mixed integer programming and we used NSGAII method to solve the resulted problem. The performance of the proposed model is examined with several examples using various probability distribution and they are compared with the performance of other existing method.

49 CFR 176.76 - Transport vehicles, freight containers, and portable tanks containing hazardous materials.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Transport vehicles, freight containers, and... TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS CARRIAGE BY VESSEL General Handling and Stowage § 176.76 Transport... paragraphs (b) through (f) of this section, hazardous materials authorized to be transported by vessel may be...

Biological reference materials and analysis of toxic elements

Energy Technology Data Exchange (ETDEWEB)

Subramanian, R; Sukumar, A

1988-12-01

Biological monitoring of toxic metal pollution in the environment requires quality control analysis with use of standard reference materials. A variety of biological tissues are increasingly used for analysis of element bioaccumulation, but the available Certified Reference Materials (CRMs) are insufficient. An attempt is made to review the studies made using biological reference materials for animal and human tissues. The need to have inter-laboratory studies and CRM in the field of biological monitoring of toxic metals is also discussed.

Integrated risk reduction framework to improve railway hazardous materials transportation safety

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiang, E-mail: liu94@illinois.edu; Saat, M. Rapik, E-mail: mohdsaat@illinois.edu; Barkan, Christopher P.L., E-mail: cbarkan@illinois.edu

2013-09-15

Highlights: • An integrated framework is developed to optimize risk reduction. • A negative binomial regression model is developed to analyze accident-cause-specific railcar derailment probability. • A Pareto-optimality technique is applied to determine the lowest risk given any level of resource. • A multi-attribute decision model is developed to determine the optimal amount of investment for risk reduction. • The models could aid the government and rail industry in developing cost-efficient risk reduction policy and practice. -- Abstract: Rail transportation plays a critical role to safely and efficiently transport hazardous materials. A number of strategies have been implemented or are being developed to reduce the risk of hazardous materials release from train accidents. Each of these risk reduction strategies has its safety benefit and corresponding implementation cost. However, the cost effectiveness of the integration of different risk reduction strategies is not well understood. Meanwhile, there has been growing interest in the U.S. rail industry and government to best allocate resources for improving hazardous materials transportation safety. This paper presents an optimization model that considers the combination of two types of risk reduction strategies, broken rail prevention and tank car safety design enhancement. A Pareto-optimality technique is used to maximize risk reduction at a given level of investment. The framework presented in this paper can be adapted to address a broader set of risk reduction strategies and is intended to assist decision makers for local, regional and system-wide risk management of rail hazardous materials transportation.

NBS SRM 1569 Brewer's Yeast: Is it an adequate standard reference material for testing a chromium determination in biological materials tion in biological materials

International Nuclear Information System (INIS)

Goeij, J.J.M. de; Volkers, K.J.; Tjioe, P.S.; Kroon, J.J.

1978-01-01

Some analytical experiences with NBS SRM 1569 Brewer's Yeast are presented. Against this background the adequacy of this standard reference material for the determination of chromium in biological materials is discussed. Authors have three main objections. Due to its high content of insoluble chromium-containing particles, SRM 1569 is not typical for biological materials, possibly not even for Brewer's Yeast. The chromium level of SRM 1569 is not typical for the chromium levels normally encountered in pure biological materials. The major fraction (69 +- 3 percent) of the chromium is present in a form which is insoluble under the conditions used in Author's analysis. (T.I.)

49 CFR 171.1 - Applicability of Hazardous Materials Regulations (HMR) to persons and functions.

Science.gov (United States)

2010-10-01

... $250 for each violation, except the maximum civil penalty is $110,000 if the violation results in death... and functions. Federal hazardous materials transportation law (49 U.S.C. 5101 et seq.) directs the... regulations to persons who transport hazardous materials in commerce. In addition, the law authorizes the...

Endodontic radiology, practice, and knowledge of radiation biology, hazard, and protection among clinical dental students and interns

Directory of Open Access Journals (Sweden)

Joan Emien Enabulele

2015-01-01

Full Text Available Objective: To evaluate the practice and knowledge of endodontic radiology as well as assess the knowledge of radiation biology, hazard, and protection among clinical dental students and interns. Materials and Methods: Cross-sectional study of clinical dental students and interns at University of Benin and University of Benin Teaching hospital respectively. Data was collected using a questionnaire which covered practice and knowledge of endodontic radiography, knowledge of radiation biology, hazard, and protection. Data was analyzed using Statistical Package for Social Sciences (SPSS version 17.0. Result: Seventy participants were included in the study, 40% were final year students and 24.3% house officers. Majority (95.7% agreed that they exposed radiographs as part of endodontic treatment. Only 18.6% knew that the apices of teeth should be 3mm from the border of the X-ray film, while 24.3% knew that 3mm of periapical bone should be visible on X-ray. Less than half (31.4% knew that paralleling technique was the technique of choice for endodontic radiography and this was statistically Significant in relationship to the status of the of the respondents. A few (4.3% of the respondents had knowledge of new horizons in endodontic imaging. Half of the respondents knew that damage by X-rays is mainly due to formation of free radicals. The most frequently reported radiation hazards was reduced salivary flow, while the least reported was rampant caries. Most knew how to protect patients, themselves, and other persons while exposing radiographs. Conclusion: There is need for inclusion of endodontic radiography in the undergraduate curriculum to ensure proper and correct radiographs during endodontic procedure.

76 FR 73011 - Pipeline and Hazardous Materials Safety Administration

Science.gov (United States)

2011-11-28

... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration Office of... Safety Administration (PHMSA), DOT. ACTION: Notice of actions on Special Permit Applications. SUMMARY: In... reissue the Nuclear 173.56(b)(3)(i special permit Security ). originally issued Administration on an...

ENVIRONMENTALLY SOUND DISPOSAL OF RADIOACTIVE MATERIALS AT A RCRA HAZARDOUS WASTE DISPOSAL FACILITY

International Nuclear Information System (INIS)

Romano, Stephen; Welling, Steven; Bell, Simon

2003-01-01

The use of hazardous waste disposal facilities permitted under the Resource Conservation and Recovery Act (''RCRA'') to dispose of low concentration and exempt radioactive materials is a cost-effective option for government and industry waste generators. The hazardous and PCB waste disposal facility operated by US Ecology Idaho, Inc. near Grand View, Idaho provides environmentally sound disposal services to both government and private industry waste generators. The Idaho facility is a major recipient of U.S. Army Corps of Engineers FUSRAP program waste and received permit approval to receive an expanded range of radioactive materials in 2001. The site has disposed of more than 300,000 tons of radioactive materials from the federal government during the past five years. This paper presents the capabilities of the Grand View, Idaho hazardous waste facility to accept radioactive materials, site-specific acceptance criteria and performance assessment, radiological safety and environmental monitoring program information

Materiomics: biological protein materials, from nano to macro

Science.gov (United States)

Cranford, Steven; Buehler, Markus J

2010-01-01

Materiomics is an emerging field of science that provides a basis for multiscale material system characterization, inspired in part by natural, for example, protein-based materials. Here we outline the scope and explain the motivation of the field of materiomics, as well as demonstrate the benefits of a materiomic approach in the understanding of biological and natural materials as well as in the design of de novo materials. We discuss recent studies that exemplify the impact of materiomics – discovering Nature’s complexity through a materials science approach that merges concepts of material and structure throughout all scales and incorporates feedback loops that facilitate sensing and resulting structural changes at multiple scales. The development and application of materiomics is illustrated for the specific case of protein-based materials, which constitute the building blocks of a variety of biological systems such as tendon, bone, skin, spider silk, cells, and tissue, as well as natural composite material systems (a combination of protein-based and inorganic constituents) such as nacre and mollusk shells, and other natural multiscale systems such as cellulose-based plant and wood materials. An important trait of these materials is that they display distinctive hierarchical structures across multiple scales, where molecular details are exhibited in macroscale mechanical responses. Protein materials are intriguing examples of materials that balance multiple tasks, representing some of the most sustainable material solutions that integrate structure and function despite severe limitations in the quality and quantity of material building blocks. However, up until now, our attempts to analyze and replicate Nature’s materials have been hindered by our lack of fundamental understanding of these materials’ intricate hierarchical structures, scale-bridging mechanisms, and complex material components that bestow protein-based materials their unique properties

Hazardous Material Cargo Frustration at Military Aerial Ports of Embarkation

National Research Council Canada - National Science Library

Christensen, Neil E

2006-01-01

Since military units often require critical hazardous materials in an expedited manner, identifying choke points within the supply chain is necessary to improve logistic support to front line forces...

77 FR 22504 - Hazardous Materials; Packages Intended for Transport by Aircraft

Science.gov (United States)

2012-04-16

... Convention on International Civil Aviation--also known as the Chicago Convention. Future inconsistencies with... known as the Chicago Convention. Future inconsistencies with international transport standards may... material release. Releases of hazardous materials can result in explosions or fires, while radioactive...

Hazardous Materials Transportation Act. Hearing before the Subcommittee on Transportation, Tourism, and Hazardous Materials of the Committee on Energy and Commerce, House of Representatives, One Hundredth Congress, First Session, July 30, 1987

Energy Technology Data Exchange (ETDEWEB)

1988-01-01

About 1.5 billion tons of hazardous materials per year are moved in the US by truck, rail, barge, and air. The Hazardous Materials Transportation Act was the first attempt at a comprehensive Federal scheme for regulation. This hearing looks at the Secretary of Transportation's implementation of the statute for oversight and reauthorization responsibilities. Testimony was heard from 16 witnesses, representatives of Chemical Manufacturers Association, the American Trucking Association, the Association of American Railroads, the Department of Transportation, the Environmental Protection Agency, the Environmental Policy Institute, Office of Technology Assessment, Hazardous Materials Advisory Council, National Tank Truck Carriers, Federal Emergency Management Agency, National Paint and Coatings Association, and a representative from Ohio.

Materiomics: biological protein materials, from nano to macro

Directory of Open Access Journals (Sweden)

Steven Cranford

2010-11-01

Full Text Available Steven Cranford, Markus J BuehlerCenter for Materials Science and Engineering, Laboratory for Atomistic and Molecular Mechanics, Department of Civil and Environmental Engineering, Massachusetts Institute of Technology, Cambridge, MA, USAAbstract: Materiomics is an emerging field of science that provides a basis for multiscale material system characterization, inspired in part by natural, for example, protein-based materials. Here we outline the scope and explain the motivation of the field of materiomics, as well as demonstrate the benefits of a materiomic approach in the understanding of biological and natural materials as well as in the design of de novo materials. We discuss recent studies that exemplify the impact of materiomics – discovering Nature’s complexity through a materials science approach that merges concepts of material and structure throughout all scales and incorporates feedback loops that facilitate sensing and resulting structural changes at multiple scales. The development and application of materiomics is illustrated for the specific case of protein-based materials, which constitute the building blocks of a variety of biological systems such as tendon, bone, skin, spider silk, cells, and tissue, as well as natural composite material systems (a combination of protein-based and inorganic constituents such as nacre and mollusk shells, and other natural multiscale systems such as cellulose-based plant and wood materials. An important trait of these materials is that they display distinctive hierarchical structures across multiple scales, where molecular details are exhibited in macroscale mechanical responses. Protein materials are intriguing examples of materials that balance multiple tasks, representing some of the most sustainable material solutions that integrate structure and function despite severe limitations in the quality and quantity of material building blocks. However, up until now, our attempts to analyze and

78 FR 1119 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2013-01-07

...: Transportation of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... lithium cells and batteries that have been adopted into the 2013-2014 International Civil Aviation... edition, when transporting batteries domestically by air. Incorporation by reference of the 2013-2014...

Safety in the Chemical Laboratory: Certifications for Professional Hazardous Materials and Waste Management.

Science.gov (United States)

Fischer, Kenneth E.

1988-01-01

Discusses the need for determining a curriculum to provide qualified hazardous waste personnel. Describes the needed role of colleges and universities and current hazardous materials certification requirements. Lists requirements for 18 professional certifications. (MVL)

Development of an expert system for transportation of hazardous and radioactive materials

International Nuclear Information System (INIS)

Ferrada, J.J.; Michelhaugh, R.D.; Rawl, R.R.

1994-01-01

Under the sponsorship of the US Department of Energy's (DOE's) Transportation Management Division (EM-261), the Transportation Technologies Group at Oak Ridge National Laboratory (ORNL) has designed and developed an expert system prototype application of the hazardous materials transportation regulations. The objective of this task was to provide a proof-of-concept for developing a computerized expert system that will ensure straightforward, consistent, and error-free application of the hazardous materials transportation regulations. The expert system prototype entailed the analysis of what an expert in hazardous materials shipping information could/should do. From the analysis of the different features required for the expert system prototype, it was concluded that the developmental efforts should be directed to a Windows trademark 3.1 hypermedia environment. Hypermedia technology usually works as an interactive software system that gives personal computer users the ability to organize, manage, and present information in a number of formats--text, graphics, sound, and full-motion video

77 FR 21714 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2012-04-11

...: Transportation of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... cells and batteries that have been adopted into the 2013-2014 International Civil Aviation Organization...) to address the air transportation risks posed by lithium cells and batteries. Some of the proposals...

75 FR 1302 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2010-01-11

... of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... transportation of lithium cells and batteries, including lithium cells and batteries packed with or contained in equipment. The proposed changes are intended to enhance safety by ensuring that all lithium batteries are...

Probability analysis of multiple-tank-car release incidents in railway hazardous materials transportation

International Nuclear Information System (INIS)

Liu, Xiang; Saat, Mohd Rapik; Barkan, Christopher P.L.

2014-01-01

Railroads play a key role in the transportation of hazardous materials in North America. Rail transport differs from highway transport in several aspects, an important one being that rail transport involves trains in which many railcars carrying hazardous materials travel together. By contrast to truck accidents, it is possible that a train accident may involve multiple hazardous materials cars derailing and releasing contents with consequently greater potential impact on human health, property and the environment. In this paper, a probabilistic model is developed to estimate the probability distribution of the number of tank cars releasing contents in a train derailment. Principal operational characteristics considered include train length, derailment speed, accident cause, position of the first car derailed, number and placement of tank cars in a train and tank car safety design. The effect of train speed, tank car safety design and tank car positions in a train were evaluated regarding the number of cars that release their contents in a derailment. This research provides insights regarding the circumstances affecting multiple-tank-car release incidents and potential strategies to reduce their occurrences. The model can be incorporated into a larger risk management framework to enable better local, regional and national safety management of hazardous materials transportation by rail

Probability analysis of multiple-tank-car release incidents in railway hazardous materials transportation

Energy Technology Data Exchange (ETDEWEB)

Liu, Xiang, E-mail: liu94@illinois.edu; Saat, Mohd Rapik, E-mail: mohdsaat@illinois.edu; Barkan, Christopher P.L., E-mail: cbarkan@illinois.edu

2014-07-15

Railroads play a key role in the transportation of hazardous materials in North America. Rail transport differs from highway transport in several aspects, an important one being that rail transport involves trains in which many railcars carrying hazardous materials travel together. By contrast to truck accidents, it is possible that a train accident may involve multiple hazardous materials cars derailing and releasing contents with consequently greater potential impact on human health, property and the environment. In this paper, a probabilistic model is developed to estimate the probability distribution of the number of tank cars releasing contents in a train derailment. Principal operational characteristics considered include train length, derailment speed, accident cause, position of the first car derailed, number and placement of tank cars in a train and tank car safety design. The effect of train speed, tank car safety design and tank car positions in a train were evaluated regarding the number of cars that release their contents in a derailment. This research provides insights regarding the circumstances affecting multiple-tank-car release incidents and potential strategies to reduce their occurrences. The model can be incorporated into a larger risk management framework to enable better local, regional and national safety management of hazardous materials transportation by rail.

Preliminary proposed seismic design and evaluation criteria for new and existing underground hazardous materials storage tanks

International Nuclear Information System (INIS)

Kennedy, R.P.

1991-01-01

The document provides a recommended set of deterministic seismic design and evaluation criteria for either new or existing underground hazardous materials storage tanks placed in either the high hazard or moderate hazard usage catagories of UCRL-15910. The criteria given herein are consistent with and follow the same philosophy as those given in UCRL-15910 for the US Department of Energy facilities. This document is intended to supplement and amplify upon Reference 1 for underground hazardous materials storage tanks

EFSA BIOHAZ Panel (EFSA Panel on Biological Hazards), 2013. Scientific Opinion on the public health hazards to be covered by inspection of meat from farmed game

DEFF Research Database (Denmark)

Hald, Tine; Baggesen, Dorte Lau

ranked as medium or lower potential concern. More effective control of biological hazards could be achieved using an integrated farm to chilled carcass approach, including improved food chain information (FCI) and risk-based controls. Further studies are required on Salmonella spp. in farmed wild boar...... and T. gondii in farmed wild boar and farmed deer. If new information confirms a high risk to public health from meat from these species, setting targets at carcass level should be considered. Palpation and incision should be omitted, as it will not detect biological hazards considered to be a high......Salmonella spp. in farmed wild boar and Toxoplasma gondii in farmed deer and farmed wild boar were ranked as a high priority for meat inspection. Trichinella spp. in wild boar was ranked as low priority due to current controls, which should be continued. For chemical hazards, all substances were...

Biological materials: a materials science approach.

Science.gov (United States)

Meyers, Marc A; Chen, Po-Yu; Lopez, Maria I; Seki, Yasuaki; Lin, Albert Y M

2011-07-01

The approach used by Materials Science and Engineering is revealing new aspects in the structure and properties of biological materials. The integration of advanced characterization, mechanical testing, and modeling methods can rationalize heretofore unexplained aspects of these structures. As an illustration of the power of this methodology, we apply it to biomineralized shells, avian beaks and feathers, and fish scales. We also present a few selected bioinspired applications: Velcro, an Al2O3-PMMA composite inspired by the abalone shell, and synthetic attachment devices inspired by gecko. Copyright © 2010 Elsevier Ltd. All rights reserved.

Removal of radioactive and other hazardous material from fluid waste

Science.gov (United States)

Tranter, Troy J [Idaho Falls, ID; Knecht, Dieter A [Idaho Falls, ID; Todd, Terry A [Aberdeen, ID; Burchfield, Larry A [W. Richland, WA; Anshits, Alexander G [Krasnoyarsk, RU; Vereshchagina, Tatiana [Krasnoyarsk, RU; Tretyakov, Alexander A [Zheleznogorsk, RU; Aloy, Albert S [St. Petersburg, RU; Sapozhnikova, Natalia V [St. Petersburg, RU

2006-10-03

Hollow glass microspheres obtained from fly ash (cenospheres) are impregnated with extractants/ion-exchangers and used to remove hazardous material from fluid waste. In a preferred embodiment the microsphere material is loaded with ammonium molybdophosphonate (AMP) and used to remove radioactive ions, such as cesium-137, from acidic liquid wastes. In another preferred embodiment, the microsphere material is loaded with octyl(phenyl)-N-N-diisobutyl-carbamoylmethylphosphine oxide (CMPO) and used to remove americium and plutonium from acidic liquid wastes.

An OSHA based approach to safety analysis for nonradiological hazardous materials

International Nuclear Information System (INIS)

Yurconic, M.

1992-08-01

The PNL method for chemical hazard classification defines major hazards by means of a list of hazardous substances (or chemical groups) with associated trigger quantities. In addition, the functional characteristics of the facility being classified is also be factored into the classification. In this way, installations defined as major hazard will only be those which have the potential for causing very serious incidents both on and off site. Because of the diversity of operations involving chemicals, it may not be possible to restrict major hazard facilities to certain types of operations. However, this hazard classification method recognizes that in the industrial sector major hazards are most commonly associated with activities involving very large quantities of chemicals and inherently energetic processes. These include operations like petrochemical plants, chemical production, LPG storage, explosives manufacturing, and facilities which use chlorine, ammonia, or other highly toxic gases in bulk quantities. The basis for this methodology is derived from concepts used by OSHA in its proposed chemical process safety standard, the Dow Fire and Explosion Index Hazard Classification Guide, and the International Labor Office's program on chemical safety. For the purpose of identifying major hazard facilities, this method uses two sorting criteria, (1) facility function and processes and (2) quantity of substances to identify facilities requiringclassification. Then, a measure of chemical energy potential (material factor) is used to identify high hazard class facilities

A routine chromium determination in biological materials; application to various reference materials and standard reference materials

International Nuclear Information System (INIS)

Tjioe, P.S.; Goeij, J.J.M. de; Volkers, K.J.

1979-01-01

The determination limit under standard working conditions of chromium in biological materials is discussed. Neutron activation analysis and atomic spectrometry have been described for some analytical experiences with NBS SRM 1577 reference material. The chromium determination is a part of a larger multi-element scheme for the determination of 12 elements in biological materials

Proceedings of emerging technologies for hazardous waste management

International Nuclear Information System (INIS)

Tedder, D.W.

1992-01-01

This paper contains the proceedings of emergin technologies for hazardous waste management. Topics covered include: advanced transuranic waste managements; remediation of soil/water systems contaminated with nonaqueous pollutants; advances in molten salt oxidation; air treatment and protection; advanced waste minimization strategies; removal of hazardous materials from soils or groundwater; bioremediation of soils and sediment; innovation, monitoring, and asbestos; high-level liquid waste chemistry in the Hanford tanks; biological contributions to soil and groundwater remediation; soil treatment technologies; pollution prevention; incineration and vitrification; current technology; systematic design approaches to hazardous waste management; waste management and environmental restoration at Savannah River; soil washing and flushing for remediation of hazardous wastes

Expert systems for the transportation of hazardous and radioactive materials

International Nuclear Information System (INIS)

Luce, C.E.; Clover, J.C.; Ferrada, J.J.

1994-01-01

Under the supervision of the Transportation Technologies Group which is in the Chemical Technology Division at Oak Ridge National Laboratory, an expert system prototype for the transportation and packaging of hazardous and radioactive materials has been designed and developed. The development of the expert system prototype focused on using the combination of hypermedia elements and the Visual Basic trademark programming language. Hypermedia technology uses software that allows the user to interact with the computing environment through many formats: text, graphics, audio, and full-motion video. With the use of hypermedia, a user-friendly prototype has been developed to sort through numerous transportation regulations, thereby leading to the proper packaging for the materials. The expert system performs the analysis of regulations that an expert in shipping information would do; only the expert system performs the work more quickly. Currently, enhancements in a variety of categories are being made to the prototype. These include further expansion of non-radioactive materials, which includes any material that is hazardous but not radioactive; and the addition of full-motion video, which will depict regulations in terms that are easy to understand and which will show examples of how to handle the materials when packaging them

75 FR 9147 - Hazardous Materials: Transportation of Lithium Batteries

Science.gov (United States)

2010-03-01

...: Transportation of Lithium Batteries AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT... transport of lithium cells and batteries. PHMSA and FAA will hold a public meeting on March 5, 2010, in... will be attending the Lithium Battery Public Meeting and wait to be escorted to the Conference Center...

49 CFR 171.16 - Detailed hazardous materials incident reports.

Science.gov (United States)

2010-10-01

... containing any hazardous material suffers structural damage to the lading retention system or damage that..., explosion or dangerous evolution of heat (i.e., an amount of heat sufficient to be dangerous to packaging or personal safety to include charring of packaging, melting of packaging, scorching of packaging, or other...

[Synthetic biology and rearrangements of microbial genetic material].

Science.gov (United States)

Liang, Quan-Feng; Wang, Qian; Qi, Qing-Sheng

2011-10-01

As an emerging discipline, synthetic biology has shown great scientific values and application prospects. Although there have been many reviews of various aspects on synthetic biology over the last years, this article, for the first time, attempted to discuss the relationship and difference between microbial genetics and synthetic biology. We summarized the recent development of synthetic biology in rearranging microbial genetic materials, including synthesis, design and reduction of genetic materials, standardization of genetic parts and modularization of genetic circuits. The relationship between synthetic biology and microbial genetic engineering was also discussed in the paper.

Written instructions for the transport of hazardous materials: Accident management instruction sheets

International Nuclear Information System (INIS)

Ridder, K.

1988-01-01

In spite of the regulations and the safety provisions taken, accidents are not entirely avoidable in the transport of hazardous materials. For managing an accident and preventing further hazards after release of dangerous substances, the vehicle drivers must carry with them the accident management instruction sheets, which give instructions on immediate counter measures to be taken by the driver, and on information to be given to the police and the fire brigades. The article in hand discusses the purpose, the contents, and practice-based improvement of this collection of instruction sheets. Particular reference is given to the newly revised version of June 15, 1988 (Verkehrsblatt 1/88) of the 'Directives for setting up accident management instruction sheets - written instructions - for road transport of hazardous materials', as issued by the Federal Ministry of Transport. (orig./HP) [de

THE DEVELOPMENT OF BIOLOGY MATERIAL RESOURCES BY METACOGNITIVE STRATEGY

Directory of Open Access Journals (Sweden)

Endang Susantini

2016-02-01

Full Text Available The Development of Biology Material Resources by Metacognitive Strategy The study was aimed at finding out the suitability of Biology Materials using the metacognitive strategy. The materials were textbooks, self-understanding Evaluation Sheet and the key, lesson plan, and tests including the answer key. The criteria of appropriateness included the relevance of the resources with the content validity, face va­lidity and the language. This research and development study was carried out employing a 3D model, namely define, design and develop. At the define stage, three topics were selected for analysis, they were virus, Endocrine System, and Genetic material. During the design phase, the physical appearance of the materials was suited with the Metacognitive Strategy. At the develop phase, the material resources were examined and validated by two Biology experts and senior teachers of Biology. The results showed that the Biology material Resources using Metacognitive Strategy developed in the study has fell into the category of very good ( score > 3.31 and was therefore considered suitable.

78 FR 66326 - Hazardous Materials: Rail Petitions and Recommendations To Improve the Safety of Railroad Tank...

Science.gov (United States)

2013-11-05

...: Rail Petitions and Recommendations To Improve the Safety of Railroad Tank Car Transportation (RRR) AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA), DOT. ACTION: Advance Notice of... DEPARTMENT OF TRANSPORTATION Pipeline and Hazardous Materials Safety Administration 49 CFR Parts...

Dendritic cells and skin sensitization: Biological roles and uses in hazard identification

International Nuclear Information System (INIS)

Ryan, Cindy A.; Kimber, Ian; Basketter, David A.; Pallardy, Marc; Gildea, Lucy A.; Gerberick, G. Frank

2007-01-01

Recent advances have been made in our understanding of the roles played by cutaneous dendritic cells (DCs) in the induction of contact allergy. A number of associated changes in epidermal Langerhans cell phenotype and function required for effective skin sensitization are providing the foundations for the development of cellular assays (using DC and DC-like cells) for skin sensitization hazard identification. These alternative approaches to the identification and characterization of skin sensitizing chemicals were the focus of a Workshop entitled 'Dendritic Cells and Skin Sensitization: Biological Roles and Uses in Hazard Identification' that was given at the annual Society of Toxicology meeting held March 6-9, 2006 in San Diego, California. This paper reports information that was presented during the Workshop

Method and apparatus for the management of hazardous waste material

Science.gov (United States)

Murray, Jr., Holt

1995-01-01

A container for storing hazardous waste material, particularly radioactive waste material, consists of a cylindrical body and lid of precipitation hardened C17510 beryllium-copper alloy, and a channel formed between the mated lid and body for receiving weld filler material of C17200 copper-beryllium alloy. The weld filler material has a precipitation hardening temperature lower than the aging kinetic temperature of the material of the body and lid, whereby the weld filler material is post weld heat treated for obtaining a weld having substantially the same physical, thermal, and electrical characteristics as the material of the body and lid. A mechanical seal assembly is located between an interior shoulder of the body and the bottom of the lid for providing a vacuum seal.

Hazardous Materials Management and Emergency Response training Center needs assessment

International Nuclear Information System (INIS)

McGinnis, K.A.; Bolton, P.A.; Robinson, R.K.

1993-09-01

For the Hanford Site to provide high-quality training using simulated job-site situations to prepare the 4,000 Site workers and 500 emergency responders for known and unknown hazards a Hazardous Materials Management and Emergency Response Training Center is needed. The center will focus on providing classroom lecture as well as hands-on, realistic training. The establishment of the center will create a partnership among the US Department of Energy; its contractors; labor; local, state, and tribal governments; and Xavier and Tulane Universities of Louisiana. This report presents the background, history, need, benefits, and associated costs of the proposed center

Hazards assessment for the Hazardous Waste Storage Facility

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-04-01

This report documents the hazards assessment for the Hazardous Waste Storage Facility (HWSF) located at the Idaho National Engineering Laboratory. The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding HWSF, the buildings and structures at HWSF, and the processes used at HWSF are described in this report. All nonradiological hazardous materials at the HWSF were identified (radiological hazardous materials are not stored at HWSF) and screened against threshold quantities according to DOE Order 5500.3A guidance. Two of the identified hazardous materials exceeded their specified threshold quantity. This report discusses the potential release scenarios and consequences associated with an accidental release for each of the two identified hazardous materials, lead and mercury. Emergency considerations, such as emergency planning zones, emergency classes, protective actions, and emergency action levels, are also discussed based on the analysis of potential consequences. Evaluation of the potential consequences indicated that the highest emergency class for operational emergencies at the HWSF would be a Site Area Emergency

Natural radioactivity level and radiological hazard assessment of commonly used building material in Xining, China

International Nuclear Information System (INIS)

Shigang Chao; Xinwei Lu; Mengmeng Zhang; Long Pang

2014-01-01

Natural radioactivity of the commonly used building materials in Xining of China was measured using gamma-ray spectrometer system comprising a NaI(Tl) detector. Radioactivity concentrations of 226 Ra, 232 Th and 40 K in the studied samples range from 11.6 to 120.6, 10.2 to 107.1 and 228.0 to 1,036.2 Bq kg -1 , respectively. The concentrations for these natural radionuclides were compared with the reported data of other countries and the mean value for soil. Radium equivalent activity, indoor air absorbed dose rate, annual effective dose rate as well as external and internal hazard indices were calculated to assess radiological hazards for people living in dwelling made of the building materials. The radiological hazard assessment results show that the studied building materials, except for some aerated concrete block samples, are safe for use in construction of dwellings in the study area and do not pose any significant source of radiation hazard. (author)

Hazardous materials emergency response training program at Texas A ampersand M University

International Nuclear Information System (INIS)

Stirling, A.G.

1989-01-01

The Texas Engineering Extension Service (TEEX) as the engineering vocational training arm of the Texas A ampersand M University system has conducted oil-spill, hazardous-material, and related safety training for industry since 1976 and fire suppression training since 1931. In 1987 TEEX conducted training for some 66,000 persons, of which some 6000 were in hazardous-materials safety training and 22,000 in fire suppression or related fields. Various laws and regulations exist relative to employee training at an industrial facility, such as the Hazard Communication Act, the Resource Conservation and Recovery Act (RCRA), the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA or more commonly Superfund), the Community Right to Know Law, and the Superfund Amendments and Reauthorization Act (SARA), Titles I and III. The TEEX programs developed on the foundation emphasize the hands-on approach (60% field exercises) to provide a comprehensive training curriculum resulting in regulatory compliance, an effective emergency response capability, a prepared community, and a safe work environment

Robotics and artificial intelligence for hazardous environments

International Nuclear Information System (INIS)

Spelt, P.F.

1993-01-01

In our technological society, hazardous materials including toxic chemicals, flammable, explosive, and radioactive substances, and biological agents, are used and handled routinely. Each year, many workers who handle these substances are accidently contaminated, in some cases resulting in injury, death, or chronic disabilities. If these hazardous materials could be handled remotely, either with a teleoperated robot (operated by a worker in a safe location) or by an autonomous robot, then human suffering and economic costs of accidental exposures could be dramatically reduced. At present, it is still difficult for commercial robotic technology to completely replace humans involved in performing complex work tasks in hazardous environments. The robotics efforts at the Center for Engineering Systems Advanced Research represent a significant effort at contributing to the advancement of robotics for use in hazardous environments. While this effort is very broad-based, ranging from dextrous manipulation to mobility and integrated sensing, the technical portion of this paper will focus on machine learning and the high-level decision making needed for autonomous robotics

Automated extraction of DNA from reference samples from various types of biological materials on the Qiagen BioRobot EZ1 Workstation

DEFF Research Database (Denmark)

Stangegaard, Michael; Jørgensen, Mads; Hansen, Anders Johannes

2009-01-01

, and muscle biopsies. The DNA extraction was validated according to EN/ISO 17025 for the STR kits AmpFlSTR« Identifiler« and AmpFlSTR« Yfiler« (Applied Biosystems). Of 298 samples extracted, 11 (4%) did not yield acceptable results. In conclusion, we have demonstrated that extraction of DNA from various types......We have validated and implemented a protocol for DNA extraction from various types of biological materials using a Qiagen BioRobot EZ1 Workstation. The sample materials included whole blood, blood from deceased, buccal cells on Omni swabs and FTA Cards, blood on FTA Cards and cotton swabs...... of biological material can be performed quickly and without the use of hazardous chemicals, and that the DNA may be successfully STR typed according to the requirements of forensic genetic investigations accredited according to EN/ISO 17025...

Some relevant parameters for assessing fire hazards of combustible mine materials using laboratory scale experiments.

Science.gov (United States)

Litton, Charles D; Perera, Inoka E; Harteis, Samuel P; Teacoach, Kara A; DeRosa, Maria I; Thomas, Richard A; Smith, Alex C

2018-04-15

When combustible materials ignite and burn, the potential for fire growth and flame spread represents an obvious hazard, but during these processes of ignition and flaming, other life hazards present themselves and should be included to ensure an effective overall analysis of the relevant fire hazards. In particular, the gases and smoke produced both during the smoldering stages of fires leading to ignition and during the advanced flaming stages of a developing fire serve to contaminate the surrounding atmosphere, potentially producing elevated levels of toxicity and high levels of smoke obscuration that render the environment untenable. In underground mines, these hazards may be exacerbated by the existing forced ventilation that can carry the gases and smoke to locations far-removed from the fire location. Clearly, materials that require high temperatures (above 1400 K) and that exhibit low mass loss during thermal decomposition, or that require high heat fluxes or heat transfer rates to ignite represent less of a hazard than materials that decompose at low temperatures or ignite at low levels of heat flux. In order to define and quantify some possible parameters that can be used to assess these hazards, small-scale laboratory experiments were conducted in a number of configurations to measure: 1) the toxic gases and smoke produced both during non-flaming and flaming combustion; 2) mass loss rates as a function of temperature to determine ease of thermal decomposition; and 3) mass loss rates and times to ignition as a function of incident heat flux. This paper describes the experiments that were conducted, their results, and the development of a set of parameters that could possibly be used to assess the overall fire hazard of combustible materials using small scale laboratory experiments.

78 FR 69745 - Safety and Security Plans for Class 3 Hazardous Materials Transported by Rail

Science.gov (United States)

2013-11-20

... material (considering the material's underlying chemical properties, corrosivity, and other characteristics) is fundamental to ensuring the selection of proper packaging and that the hazards of the materials...

Performance-oriented packagings for hazardous materials: Resource guide

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

This document provides recommendations to US Department of Energy (DOE) shippers regarding packaging that meet performance-oriented packaging requirements implemented by US Department of Transportation (DOT) in rulemaking HM-181 (December 21, 1990) and subsequent actions. The packaging described in this document are certified by their vendor to comply with requirements for Packing Group I, II, or III hazardous materials packaging. The intent of this document is to share information between DOE and contractors and at all DOE facilities.

Performance-oriented packagings for hazardous materials: Resource guide

International Nuclear Information System (INIS)

1993-09-01

This document provides recommendations to US Department of Energy (DOE) shippers regarding packaging that meet performance-oriented packaging requirements implemented by US Department of Transportation (DOT) in rulemaking HM-181 (December 21, 1990) and subsequent actions. The packaging described in this document are certified by their vendor to comply with requirements for Packing Group I, II, or III hazardous materials packaging. The intent of this document is to share information between DOE and contractors and at all DOE facilities

Developments in consequence modelling of accidental releases of hazardous materials

NARCIS (Netherlands)

Boot, H.

2012-01-01

The modelling of consequences of releases of hazardous materials in the Netherlands has mainly been based on the “Yellow Book”. Although there is no updated version of this official publication, new insights have been developed during the last decades. This article will give an overview of new

Impacts on health and safety from transfer/consolidation of nuclear materials and hazardous chemicals

International Nuclear Information System (INIS)

Gallucci, R.H.V.

1994-11-01

Environmental restoration plans at the US Department of Energy (USDOE) Hanford Site calls for transfer/consolidation of ''targets/threats,'' namely nuclear materials and hazardous chemicals. Reductions in the health and safety hazards will depend on the plans implemented. Pacific Northwest Laboratory (PNL) estimated these potential impacts, assuming implementation of the current reference plan and employing ongoing risk and safety analyses. The results indicated the potential for ''significant'' reductions in health and safety hazards in the long term (> 25 years) and a potentially ''noteworthy'' reduction in health hazard in the short term (≤ 25 years)

Analysis on the Industrial Design of Food Package and the Component of Hazardous Substance in the Packaging Material

OpenAIRE

Wei-Wen Huang

2015-01-01

Transferring the hazardous chemicals contained in food packaging materials into food would threaten the health of consumers, therefore, the related laws and regulations and the detection method of hazardous substance have been established at home and abroad to ensure the safety to use the food packaging material. According to the analysis on the hazardous component in the food packaging, a set of detection methods for hazardous substance in the food packaging was established in the paper and ...

77 FR 36607 - Office of Hazardous Materials Safety Notice of Applications for Modification of Special Permit

Science.gov (United States)

2012-06-19

... modification of special permits (e.g. to provide for additional hazardous materials, packaging design changes... hazardous materials. 12102-M EQ Industrial 49 CFR 173.56(i); To modify the special Services, Inc. 173.56(b... 4.1. 13102-M Robertshaw Industrial 49 CFR 173.150(b); To modify the special Products dba 173.222(c...

Natural radioactivity in some building materials and assessment of the associated radiation hazards

Energy Technology Data Exchange (ETDEWEB)

Kasumovic, Amira; Hankic, Ema; Kasic, Amela; Adrovic, Feriz [Tuzla Univ. (Bosnia and Herzegovina). Dept. of Physics

2018-04-01

The results of the specific activities of {sup 232}Th, {sup 226}Ra and {sup 40}K measured in samples of commonly used building materials in Bosnia and Herzegovina are presented. Measurements were performed by gamma-ray spectrometer with coaxial HPGe detector. The surface radon exhalation and mass exhalation rates for selected building materials were also measured. The determined values of specific activities were in range from 3.16 ± 0.81 Bq kg{sup -1} to 64.79 ± 6.16 Bq kg{sup -1} for {sup 232}Th, from 2.46 ± 0.95 Bq kg{sup -1} to 53.89 ± 3.67 Bq kg{sup -1} for {sup 226}Ra and from 28.44 ± 7.28 Bq kg{sup -1} to 557.30 ± 93.38 Bq kg{sup -1} for {sup 40}K. The radium equivalent activity, the activity concentration index, the external and internal hazard indices as well as the absorbed dose rate in indoor air and the corresponding annual effective dose, due to gamma-ray emission from the radioactive nuclides in the building material, were evaluated in order to assess the radiation hazards for people. The measured specific activities of the natural radioactive nuclides in all investigated building materials were compared with the published results for building materials from other European countries. It can be noted that the results from this study are similar to the data for building materials from neighbouring countries and for building materials used in the EU Member States. The radiological hazard parameters of the building materials were all within the recommended limits for safety use.

Conduit for regeneration of biological material

DEFF Research Database (Denmark)

2016-01-01

The present invention relates to a conduit comprising a first material, having 1) a through-going hole, 2) fibers aligned along the long-axis in the through-going hole, each fiber having a diameter in the range 200-2000 nm. The conduit is preferably for regeneration of biological material, even...

An integrated risk communication system for the transport of hazardous materials

International Nuclear Information System (INIS)

Minor, J.W. IV; Abkowitz, M.D.

2004-01-01

This paper describes the development and implementation of the prototype of an an internet-based, risk communication system prototype for the transport of hazardous materials. The system was designed with the objectives of: (1) incorporating functionality and features that are useful for meeting a variety of risk communication needs, and (2) demonstrating a high degree of interaction among system components, enabling customisation to meet the specific transport risk communication needs requirements of the host organisation. To demonstrate 'proof of concept', the system is applied to two scenarios: 1) building knowledge and awareness, focusing on how information can be entered, organised and disseminated to the public and other transport stakeholders, and 2) emergency management, utilising the system for securely managing information in responding to a transport incident involving hazardous materials transport incident. The effectiveness of the system in these applications is subsequently discussed. (author)

Viscoelastic characterization of soft biological materials

Science.gov (United States)

Nayar, Vinod Timothy

Progressive and irreversible retinal diseases are among the primary causes of blindness in the United States, attacking the cells in the eye that transform environmental light into neural signals for the optic pathway. Medical implants designed to restore visual function to afflicted patients can cause mechanical stress and ultimately damage to the host tissues. Research shows that an accurate understanding of the mechanical properties of the biological tissues can reduce damage and lead to designs with improved safety and efficacy. Prior studies on the mechanical properties of biological tissues show characterization of these materials can be affected by environmental, length-scale, time, mounting, stiffness, size, viscoelastic, and methodological conditions. Using porcine sclera tissue, the effects of environmental, time, and mounting conditions are evaluated when using nanoindentation. Quasi-static tests are used to measure reduced modulus during extended exposure to phosphate-buffered saline (PBS), as well as the chemical and mechanical analysis of mounting the sample to a solid substrate using cyanoacrylate. The less destructive nature of nanoindentation tests allows for variance of tests within a single sample to be compared to the variance between samples. The results indicate that the environmental, time, and mounting conditions can be controlled for using modified nanoindentation procedures for biological samples and are in line with averages modulus values from previous studies but with increased precision. By using the quasi-static and dynamic characterization capabilities of the nanoindentation setup, the additional stiffness and viscoelastic variables are measured. Different quasi-static control methods were evaluated along with maximum load parameters and produced no significant difference in reported reduced modulus values. Dynamic characterization tests varied frequency and quasi-static load, showing that the agar could be modeled as a linearly

The transportation of hazardous materials

International Nuclear Information System (INIS)

Hillman, J.C.

1981-04-01

The increasing use of dangerous chemicals and petroleum products by S.A. industry makes it necessary for some form of control to be introduced to regulate the transport of these materials before a major disaster occurs, such as has occurred overseas. This report examines all the aspects that could increase the likelihood of such a disaster occurring, including the preparedness of emergency services. It also recommends the improvements or changes required to minimize this possibility. It is apparent that the training and ability of vehicle drivers are key areas in this respect and they are discussed at length. Forthcoming regulations under the Hazardous Substances Act No. 15 of 1973 are examined and the effects of over-restrictive legislation considered. The report concludes that legislation promulgated gradually to reinforce voluntary industrial practices will ultimately restrict this type of transport to the safety-conscious and competent operator, therefore minimizing the risk as much as possible

Integrating Hazardous Materials Characterization and Assessment Tools to Guide Pollution Prevention in Electronic Products and Manufacturing

Science.gov (United States)

Lam, Carl

Due to technology proliferation, the environmental burden attributed to the production, use, and disposal of hazardous materials in electronics have become a worldwide concern. The major theme of this dissertation is to develop and apply hazardous materials assessment tools to systematically guide pollution prevention opportunities in the context of electronic product design, manufacturing and end-of-life waste management. To this extent, a comprehensive review is first provided on describing hazard traits and current assessment methods to evaluate hazardous materials. As a case study at the manufacturing level, life cycle impact assessment (LCIA)-based and risk-based screening methods are used to quantify chemical and geographic environmental impacts in the U.S. printed wiring board (PWB) industry. Results from this industrial assessment clarify priority waste streams and States to most effectively mitigate impact. With further knowledge of PWB manufacturing processes, select alternative chemical processes (e.g., spent copper etchant recovery) and material options (e.g., lead-free etch resist) are discussed. In addition, an investigation on technology transition effects for computers and televisions in the U.S. market is performed by linking dynamic materials flow and environmental assessment models. The analysis forecasts quantities of waste units generated and maps shifts in environmental impact potentials associated with metal composition changes due to product substitutions. This insight is important to understand the timing and waste quantities expected and the emerging toxic elements needed to be addressed as a consequence of technology transition. At the product level, electronic utility meter devices are evaluated to eliminate hazardous materials within product components. Development and application of a component Toxic Potential Indicator (TPI) assessment methodology highlights priority components requiring material alternatives. Alternative

Hazardous materials responder training in the new millennium

Energy Technology Data Exchange (ETDEWEB)

Turpin, R.D.; Betsinger, G.B. [U.S. Environmental Protection Agency, Edison, NJ (United States). Environmental Response Team; Merchant, S. [Environmental Tectonics Corp., Orlando, FL (United States)

2001-07-01

The Environmental Response Team (ERT) of the U.S. Environmental Protection Agency was created to provide on-site professional expertise as well as health and safety guidance to Federal on-scene coordinators during accidental oil and chemical releases. ERT provides practical technical solutions to response activities based on theory as well as actual experience. Its creation in 1978 fulfilled the requirements of the U.S. National Contingency Plan. Members of the team have developed a 40-hour Hazardous Waste Responders training course and have themselves, attended a hands-on chemical and biological warfare personnel protective clothing course provided by the U.S. Army. The course demonstrated decontamination showers, moon suits, and entry procedures to a contaminated battlefield situation. ERT continues to emphasize the importance of hands-on training and exercises. Various training programs are underway where students can learn real-time monitoring techniques and respond to simulated hazardous waste incidents. They also learn how to assess environmental, public and occupational health and safety information on the Internet. The students also run air plume models and perform wet bench chemistry experiments. With the advent of more powerful computers, the current objective is to continue with these training activities using Instructor Controlled Interactive Computer Training (ICICT).

Route selection for the transport of hazardous materials

Energy Technology Data Exchange (ETDEWEB)

Seiler, F A

1988-12-01

The factors governing the risk-weighted selection of routes for transport of hazardous materials are analyzed. Starting from a formulation for the total risk of these transports that assumes complete information, approximations for the more realistic case of partial and uncertain information are discussed. These approximations involve well-known risk assessment techniques and mathematical methods; among the latter, Monte Carlo calculations hold the most promise. The actual route selection is based on an index of total societal cost, evaluated for a set of potential routes. (author)

Assessment of natural radioactivity and radiological hazards in building materials used in Yan'an, China.

Science.gov (United States)

Lu, Xinwei; Li, Nan; Yang, Guang; Zhao, Caifeng

2013-03-01

The concentration of natural radionuclides in commonly used building materials collected from Yan'an, China, was determined using gamma ray spectroscopy with a NaI(Tl) detector. The activity concentration of ²²⁶Ra, ²³²Th, and ⁴⁰K in the studied building materials ranges from 9.4-73.1, 11.5-86.9, and 258.9-1,055.1 Bq kg⁻¹, respectively. The concentrations for these natural radionuclides were compared with the reported data of other countries and the world mean values for soil. The radium equivalent activity (Raeq), external hazard index (Hex), internal hazard index (Hin), indoor air absorbed dose rate, and annual effective dose rate due to natural radionuclides in samples were estimated to assess radiological hazards for people living in dwellings made of the studied building materials. The calculated Raeq values of all building materials (75.7-222.1 Bq kg⁻¹) are lower than the limit of 370 Bq kg⁻¹. The values of Hex and Hin are less than unity. The mean values of indoor air absorbed dose rates of all building materials (101.0 ± 14.1-177.0 ± 6.8 nGy h⁻¹) are higher than the world population-weighted average of 84 nGy h⁻¹, while the mean values of annual effective dose range from 0.50 ± 0.07-0.87 ± 0.03 mSv y⁻¹, which are lower than the recommended limit of 1 mSv y⁻¹. It is found that these materials may be used safely as construction materials and do not pose significant radiation hazards to inhabitants.

Recycling of hazardous solid waste material using high-temperature solar process heat

Energy Technology Data Exchange (ETDEWEB)

Schaffner, B.; Meier, A.; Wuillemin, D.; Hoffelner, W.; Steinfeld, A.

2003-03-01

A novel high-temperature solar chemical reactor is proposed for the thermal recycling of hazardous solid waste material using concentrated solar power. A 10 kW solar reactor prototype was designed and tested for the carbothermic reduction of electric arc furnace dusts (EAFD). The reactor was subjected to mean solar flux intensities of 2000 kW/m2 and operated in both batch and continuous mode within the temperature range 1120-1400 K. Extraction of up to 99% and 90% of the Zn originally contained in the EAFD was achieved in the residue for the batch and continuous solar experiments, respectively. The condensed off-gas products consisted mainly of Zn, Pb, and Cl. No ZnO was detected when the O{sub 2} concentration remained below 2 vol.-%. The use of concentrated solar energy as the source of process heat offers the possibility of converting hazardous solid waste material into valuable commodities for processes in closed and sustainable material cycles. (author)

Project management plan, Hazardous Materials Management and Emergency Response Training Center

International Nuclear Information System (INIS)

Borgeson, M.E.

1994-01-01

For the next 30 years, the main activities at the Hanford Site will involve the handling and cleanup of toxic substances. Thousands of workers involved in these new activities will need systematic training appropriate to their tasks and associated risks. This project is an important part of the Hanford Site mission and will enable the US Department of Energy (DOE) to meet high standards for safety. The Hazardous Materials Management and Emergency Response Training Center (HAMMER) project will construct a centralized regional training center dedicated to training hazardous materials workers and emergency responders in classrooms and with hands-on, realistic training aids representing actual field conditions. The HAMMER Training Center will provide a cost-effective, high-quality way to meet the Hanford Site training needs. The training center creates a partnership among DOE; government contractors; labor; local, state, and tribal governments; and selected institutions of higher education

Biological radiation effects

International Nuclear Information System (INIS)

Koggl, D.; Dedenkov, A.N.

1986-01-01

All nowadays problems of radio biology are considered: types of ionizing radiations, their interaction with material; damage of molecular structures and their reparation; reaction of cells and their recovery from radiation damage; reaction of the whole organism and its separate systems. Particular attention is given to the problems of radiation carcinogenesis and radiation hazard for man

Recommendations for sampling for prevention of hazards in civil defense. On analytics of chemical, biological and radioactive contaminations. Brief instruction for the CBRN (chemical, biological, radioactive, nuclear) sampling

International Nuclear Information System (INIS)

Bachmann, Udo; Biederbick, Walter; Derakshani, Nahid

2010-01-01

The recommendation for sampling for prevention of hazards in civil defense is describing the analytics of chemical, biological and radioactive contaminations and includes detail information on the sampling, protocol preparation and documentation procedures. The volume includes a separate brief instruction for the CBRN (chemical, biological, radioactive, nuclear) sampling.

Integrated Life-Cycle Hazardous Material Management: A Logistics Imperative for USAREUR and the 7th Army

National Research Council Canada - National Science Library

Werle, Christopher

2000-01-01

This report examines the benefit to be gained by integrating traditional "pharmacy" business practices in the existing supply system rather than building a parallel system for hazardous material/hazardous waste (HM/HW) management...

Biological monitoring of organic substances in workers of a hazardous waste incinerator

Energy Technology Data Exchange (ETDEWEB)

Agramunt, C.; Domingo, J.L.; Bocio, A.; Nadal, M. [Lab. of Toxicology and Environmental Health, Reus (Spain); Muller, L. [SGS GmbH, Antwerpen (Belgium)

2004-09-15

In recent years, incineration has been one of the most frequently used technologies for hazardous waste treatment. However, health risks and the potential environmental impact of hazardous waste incinerators (HWI) are still issues of major concern. The reason is the association of stack emissions of semivolatile and volatile compounds from HWI with their potential adverse health effects. Some compounds of special interest are polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs). In relation to this, HWI workers can be potentially exposed to PCDD/Fs, polychlorinated biphenyls (PCBs) and other pollutants with a well-known toxicity. Since 1999, the only HWI in Spain has been operating in Constanti (Tarragona, Catalonia). It has a burning furnace that operates at a temperature of 1100 C and can burn 30,000 tons of hazardous waste per year. The purpose of the present survey was to determine after four years of regular operations in the facility, the concentrations in blood and urine of the HWI workers of a number of organic substances directly related with HWI and to which workers could be exposed. Human biological monitoring evaluates the degree of internal exposure to a defined environmental or occupational pollutant of individuals or population groups. The results of the current study have been compared with the baseline levels.

75 FR 5258 - Hazardous Materials Transportation; Registration and Fee Assessment Program

Science.gov (United States)

2010-02-02

...) train public sector hazardous materials emergency response employees to respond to accidents and... officers, and 500,000 emergency medical services (EMS) providers. Due to the high turnover rates of... planning grants; A new $4,000,000 grant program for non-profit hazmat employee organizations to train...

Hazard evaluation of The International Fusion Materials Irradiation Facility

Energy Technology Data Exchange (ETDEWEB)

Burgazzi, Luciano [ENEA-Centro Ricerche ' Ezio Clementel' , Advanced Physics Technology Division, Via Martiri di Monte Sole, 4, 40129 Bologna (Italy)]. E-mail: burgazzi@bologna.enea.it

2005-01-15

The International Fusion Materials Irradiation Facility (IFMIF) is aimed to provide an intense neutron source by a high current deuteron linear accelerator and a high-speed lithium flow target, for testing candidate materials for fusion. Liquid lithium is being circulated through a loop and is kept at a temperature above its freezing point. In the frame of the design phase called Key Element technology Phase (KEP), jointly performed by an international team to verify the most important risk factors, safety assessment of the whole plant has been required in order to identify the hazards associated with the plant operation. This paper discusses the safety assessments that were performed and their outcome: Failure Mode and Effect Analysis (FMEA) approach has been adopted in order to accomplish the task. Main conclusions of the study is that, on account of the safety and preventive measures adopted, potential plant related hazards are confined within the IFMIF security boundaries and great care must be exercised to protect workers and site personnel from operating the plant. The analysis has provided as a result a set of Postulated Initiating Events (PIEs), that is off-normal events, that could result in hazardous consequences for the plant, together with the total frequency and the list of component failures which could induce the PIE: this assures the exhaustive list of major initiating events of accident sequences, helpful to the further accident sequence analysis phase. Finally, for each one of the individuated PIEs, the evaluation of the accident evolution, in terms of effects on the plant and relative countermeasures, has allowed to verify that adequate measures are being taken both to prevent the accident occurrence and to cope with the accident consequences, thus assuring the fulfilment of the safety requirements.

On-site transportation and handling of uranium-233 special nuclear material: Preliminary hazards and accident analysis. Final

International Nuclear Information System (INIS)

Solack, T.; West, D.; Ullman, D.; Coppock, G.; Cox, C.

1995-01-01

U-233 Special Nuclear Material (SNM) currently stored at the T-Building Storage Areas A and B must be transported to the SW/R Tritium Complex for repackaging. This SNM is in the form of oxide powder contained in glass jars which in turn are contained in heat sealed double polyethylene bags. These doubled-bagged glass jars have been primarily stored in structural steel casks and birdcages for approximately 20 years. The three casks, eight birdcages, and one pail/pressure vessel will be loaded onto a transport truck and moved over an eight day period. The Preliminary Hazards and Accident Analysis for the on-site transportation and handling of Uranium-233 Special Nuclear Material, documented herein, was performed in accordance with the format and content guidance of DOE-STD-3009-94, Preparation Guide for US Department of Energy Nonreactor Nuclear Facility Safety Analysis Reports, dated July 1994, specifically Chapter Three, Hazard and Accident Analysis. The Preliminary Hazards Analysis involved detailed walkdowns of all areas of the U-233 SNM movement route, including the T-Building Storage Area A and B, T-Building truck tunnel, and the roadway route. Extensive discussions were held with operations personnel from the Nuclear Material Control Group, Nuclear Materials Accountability Group, EG and G Mound Security and the Material Handling Systems Transportation Group. Existing documentation related to the on-site transportation of hazardous materials, T-Building and SW/R Tritium Complex SARs, and emergency preparedness/response documentation were also reviewed and analyzed to identify and develop the complete spectrum of energy source hazards

Applying radiological emergency planning experience to hazardous materials emergency planning within the nuclear industry

International Nuclear Information System (INIS)

Foltman, A.; Newsom, D.; Lerner, K.

1988-01-01

The nuclear industry has extensive radiological emergency planning (REP) experience that is directly applicable to hazardous materials emergency planning. Recently, the Feed Materials Production Center near Cincinnati, Ohio, successfully demonstrated such application. The REP experience includes conceptual bases and standards for developing plans that have been tested in hundreds of full-scale exercises. The exercise program itself is also well developed. Systematic consideration of the differences between chemical and radiological hazards shows that relatively minor changes to the REP bases and standards are necessary. Conduct of full-scale, REP-type exercises serves to test the plans, provide training, and engender confidence and credibility

AC Calorimetric Design for Dynamic of Biological Materials

OpenAIRE

Shigeo Imaizumi

2006-01-01

We developed a new AC calorimeter for the measurement of dynamic specific heat capacity in liquids, including aqueous suspensions of biological materials. This method has several advantages. The first is that a high-resolution measurement of heat capacity, inmillidegrees, can be performed as a function of temperature, even with a very small sample. Therefore, AC calorimeter is a powerful tool to study critical behavior a tphase transition in biological materials. The second advantage is that ...

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

International Nuclear Information System (INIS)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W.; Ogunseitan, Oladele A.; Schoenung, Julie M.

2013-01-01

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS 2 p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane

Petroleum and hazardous material releases from industrial facilities associated with Hurricane Katrina.

Science.gov (United States)

Santella, Nicholas; Steinberg, Laura J; Sengul, Hatice

2010-04-01

Hurricane Katrina struck an area dense with industry, causing numerous releases of petroleum and hazardous materials. This study integrates information from a number of sources to describe the frequency, causes, and effects of these releases in order to inform analysis of risk from future hurricanes. Over 200 onshore releases of hazardous chemicals, petroleum, or natural gas were reported. Storm surge was responsible for the majority of petroleum releases and failure of storage tanks was the most common mechanism of release. Of the smaller number of hazardous chemical releases reported, many were associated with flaring from plant startup, shutdown, or process upset. In areas impacted by storm surge, 10% of the facilities within the Risk Management Plan (RMP) and Toxic Release Inventory (TRI) databases and 28% of SIC 1311 facilities experienced accidental releases. In areas subject only to hurricane strength winds, a lower fraction (1% of RMP and TRI and 10% of SIC 1311 facilities) experienced a release while 1% of all facility types reported a release in areas that experienced tropical storm strength winds. Of industrial facilities surveyed, more experienced indirect disruptions such as displacement of workers, loss of electricity and communication systems, and difficulty acquiring supplies and contractors for operations or reconstruction (55%), than experienced releases. To reduce the risk of hazardous material releases and speed the return to normal operations under these difficult conditions, greater attention should be devoted to risk-based facility design and improved prevention and response planning.

Hazardous materials and toxic substances - Status report

International Nuclear Information System (INIS)

Sommerlad, R.E.

1991-01-01

The paper first forecasts what the status of hazardous wastes should be in the year 2028. The author believes all the problems will be solved: no new hazardous wastes will be being generated and the current hazardous waste problems will have been cleared up by common sense engineering. He then describes the current status of waste management of hazardous wastes, the regulatory situation, as well as combustion test programs

Natural radioactivity and associated radiation hazardous of main building materials in Yan'an, China

International Nuclear Information System (INIS)

Li Nan; Lu Xinwei; Yang Guang; Zhao Caifeng

2012-01-01

Background: With the rapidly economic development and urbanization in Yan'an city, more building materials were consumed in building construction. While the natural radioactivity level of building materials from Yan'an is limited in the literatures. Purpose: The main objective of this study is to determine the natural radioactivity level and to analyze the associated radiation hazards of building materials in Yan'an. Methods: The specific activities of natural radionuclides 226 Ra, 232 Th and 40 K in various building materials from Yan'an city were determined using low-background gamma-ray spectrometry, and their radiation hazards were evaluated according to the standard methods. Results: The results show that the specific activities of 226 Ra, 232 Th and 40 K in the building materials are 9.4-73.1, 11.5-86.9 and 258.9-1055.1 Bq/kg, respectively. The activities of 226 Ra and 232 Th, except for sand and gravel aggregate, in all other building materials are higher than the corresponding means of local soil, and the activities of 40 K in hollow brick, red-clay brick, sand and gravel aggregate exceed the means of 40 K in soil. However, the values of internal exposure index, external exposure index and gamma radiation index in all investigated building materials are less than 1. Conclusions: The radiation levels of all analyzed building materials are within the national safety standard, which indicates that all analyzed building materials can be used anywhere and they can't cause radiation hazard to the local residents. (authors)

Analytical Chemistry at the Interface Between Materials Science and Biology

Energy Technology Data Exchange (ETDEWEB)

O' Brien, Janese C. [Iowa State Univ., Ames, IA (United States)

2000-09-21

Likedlessentid sciences, anal~cd chetis~continues toreinvent itself. Moving beyond its traditional roles of identification and quantification, analytical chemistry is now expanding its frontiers into areas previously reserved to other disciplines. This work describes several research efforts that lie at the new interfaces between analytical chemistry and two of these disciplines, namely materials science and biology. In the materials science realm, the search for new materials that may have useful or unique chromatographic properties motivated the synthesis and characterization of electrically conductive sol-gels. In the biology realm, the search for new surface fabrication schemes that would permit or even improve the detection of specific biological reactions motivated the design of miniaturized biological arrays. Collectively, this work represents some of analytical chemistry’s newest forays into these disciplines. The introduction section to this dissertation provides a literature review on several of the key aspects of this work. In advance of the materials science discussion, a brief introduction into electrochemically-modulated liquid chromatography (EMLC) and sol-gel chemistry is provided. In advance of the biological discussions, brief overviews of scanning force microscopy (SFM) and the oxidative chemistry used to construct our biological arrays are provided. This section is followed by four chapters, each of which is presented as a separate manuscript, and focuses on work that describes some of our cross-disciplinary efforts within materials science and biology. This dissertation concludes with a general summary and future prospectus.

Survey of naturally occurring hazardous materials in deep geologic formations: a perspective on the relative hazard of deep burial of nuclear wastes

International Nuclear Information System (INIS)

Tonnessen, K.A.; Cohen, J.J.

1977-01-01

Hazards associated with deep burial of solidified nuclear waste are considered with reference to toxic elements in naturally occurring ore deposits. This problem is put into perspective by relating the hazard of a radioactive waste repository to that of naturally occurring geologic formations. The basis for comparison derives from a consideration of safe drinking water levels. Calculations for relative toxicity of FBR waste and light water reactor (LWR) waste in an underground repository are compared with the relative toxicity indices obtained for average concentration ore deposits. Results indicate that, over time, nuclear waste toxicity decreases to levels below those of naturally occurring hazardous materials

Rotating biological contractor treatment of 2-nitrophenol and 2-chlorophenol containing hazardous wastes

International Nuclear Information System (INIS)

Tokuz, R.Y.

1990-01-01

Rotating Biological Contactors (RBCs) have a number of advantages over other biological treatment systems. For example, they can provide high treatment efficiencies of activated sludge systems with much lower energy inputs. Organic shock loads are handled well because large biomass is present. No bulking, foaming, or floating of sludge occurs and sludge has good settleability and dewaterability. Another advantage of RBC systems is the minimal labor requirement for operation and maintenance. Even though RBC systems have these advantages, their acceptance was slow mainly due to operational problems with the earlier units (such as shaft failures) and the lack of considerable design and operation data. A review of literature shows that there is only limited information available on the wastewater treatment with RBCs. Recently, there has been considerable contributions to the knowledge on RBC technology. However, information on the treatment of organic hazardous wastes using RBCs is still very limited. This paper reports that a considerable number of studies on the biological treatment of organic hazardous compounds was sponsored by U.S. Environmental Protection Agency (EPA). For example, an EPA sponsored study examined the effect of such compounds on the performance of activated sludge process. Bench-scale continuous-flow and batch units were used. Influent was settled municipal wastewater to which toxic compounds were added. In batch operations, 2-chlorophenol and pentachlorophenol caused an increase in the effluent Chemical Oxygen Demand (COD) at an influent concentration of 5 mg/L. No adverse effect of 2-nitrophenol on the batch system was reports. 2-Chlorophenol was one of the compounds that upset the performance of continuous-flow activated sludge units, yielding higher than normal levels of effluent suspended solids

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics.

Science.gov (United States)

Eisenberg, Daniel A; Yu, Mengjing; Lam, Carl W; Ogunseitan, Oladele A; Schoenung, Julie M

2013-09-15

Copper-indium-gallium-selenium-sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS₂ p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane. Copyright © 2013 Elsevier B.V. All rights reserved.

Just-in-Time techniques as applied to hazardous materials management

OpenAIRE

Spicer, John S.

1996-01-01

Approved for public release; distribution is unlimited This study investigates the feasibility of integrating JIT techniques in the context of hazardous materials management. This study provides a description of JIT, a description of environmental compliance issues and the outgrowth of related HAZMAT policies, and a broad perspective on strategies for applying JIT to HAZMAT management. http://archive.org/details/justintimetechn00spic Lieutenant Commander, United States Navy

Source Identification of Human Biological Materials and Its Prospect in Forensic Science.

Science.gov (United States)

Zou, K N; Gui, C; Gao, Y; Yang, F; Zhou, H G

2016-06-01

Source identification of human biological materials in crime scene plays an important role in reconstructing the crime process. Searching specific genetic markers to identify the source of different human biological materials is the emphasis and difficulty of the research work of legal medical experts in recent years. This paper reviews the genetic markers which are used for identifying the source of human biological materials and studied widely, such as DNA methylation, mRNA, microRNA, microflora and protein, etc. By comparing the principles and methods of source identification of human biological materials using different kinds of genetic markers, different source of human biological material owns suitable marker types and can be identified by detecting single genetic marker or combined multiple genetic markers. Though there is no uniform standard and method for identifying the source of human biological materials in forensic laboratories at present, the research and development of a series of mature and reliable methods for distinguishing different human biological materials play the role as forensic evidence which will be the future development direction. Copyright© by the Editorial Department of Journal of Forensic Medicine.

Hazardous Materials Pharmacies - A Vital Component of a Robust P2 Program

International Nuclear Information System (INIS)

McCarter, S.

2006-01-01

Integrating pollution prevention (P2) into the Department of Energy Integrated Safety Management (ISM) - Environmental Management System (EMS) approach, required by DOE Order 450.1, leads to an enhanced ISM program at large and complex installations and facilities. One of the building blocks to integrating P2 into a comprehensive environmental and safety program is the control and tracking of the amounts, types, and flow of hazardous materials used on a facility. Hazardous materials pharmacies (typically called HazMarts) provide a solid approach to resolving this issue through business practice changes that reduce use, avoid excess, and redistribute surplus. If understood from concept to implementation, the HazMart is a powerful tool for reducing pollution at the source, tracking inventory storage, controlling usage and flow, and summarizing data for reporting requirements. Pharmacy options can range from a strict, single control point for all hazardous materials to a virtual system, where the inventory is user controlled and reported over a common system. Designing and implementing HazMarts on large, diverse installations or facilities present a unique set of issues. This is especially true of research and development (R and D) facilities where the chemical use requirements are extensive and often classified. There are often multiple sources of supply; a wide variety of chemical requirements; a mix of containers ranging from small ampoules to large bulk storage tanks; and a wide range of tools used to track hazardous materials, ranging from simple purchase inventories to sophisticated tracking software. Computer systems are often not uniform in capacity, capability, or operating systems, making it difficult to use a server-based unified tracking system software. Each of these issues has a solution or set of solutions tied to fundamental business practices. Each requires an understanding of the problem at hand, which, in turn, requires good communication among all

The Hazardous Material Technician Apprenticeship Program at Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Steiner, S.D.

1987-07-01

This document describes an apprenticeship training program for hazardous material technician. This entry-level category is achieved after approximately 216 hours of classroom and on-the-job training. Procedures for evaluating performance include in-class testing, use of on-the-job checks, and the assignment of an apprentice mentor for each trainee

Reduction of Fire Hazard in Materials for Irrigators and Water Collectors in Cooling Towers

Energy Technology Data Exchange (ETDEWEB)

Smirnov, N. V.; Konstantinova, N. I., E-mail: konstantinova-n@inbox.ru [FGBU VNIIPO of EMERCOM of Russia (All-Russian Scientific-research Institute of Fire Protection) (Russian Federation); Gordon, E. P. [Research and Production Center “Kaustik” (Russian Federation); Poedintsev, E. A. [FGBU VNIIPO of EMERCOM of Russia (All-Russian Scientific-research Institute of Fire Protection) (Russian Federation)

2016-09-15

A way of reducing the fire hazard of PVC film used to make cooling-tower irrigators and water collectors is examined. A new generation of fire retardant, nanostructured magnesium hydroxide, is used to impart fire retardant properties. The fabrication technology is optimized with a roller-calendering manufacturing technique, and the permissible ranges of fire hazard indicators for materials in irrigators and water collectors are determined.

Comparative alternative materials assessment to screen toxicity hazards in the life cycle of CIGS thin film photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Eisenberg, Daniel A.; Yu, Mengjing; Lam, Carl W. [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States); Ogunseitan, Oladele A. [University of California, Irvine, Irvine, CA 92697 (United States); Schoenung, Julie M., E-mail: jmschoenung@ucdavis.edu [University of California, Davis, 1 Shields Avenue, Davis, CA 95616 (United States)

2013-09-15

Highlights: • Comparative alternatives assessment of thin film manufacturing technologies. • Development of chemical alternatives assessment in a life cycle context. • Screening of manufacturing and solar cell hazardous substances simultaneously. -- Abstract: Copper–indium–gallium–selenium–sulfide (CIGS) thin film photovoltaics are increasingly penetrating the market supply for consumer solar panels. Although CIGS is attractive for producing less greenhouse gas emissions than fossil-fuel based energy sources, CIGS manufacturing processes and solar cell devices use hazardous materials that should be carefully considered in evaluating and comparing net environmental benefits of energy products. Through this research, we present a case study on the toxicity hazards associated with alternative materials selection for CIGS manufacturing. We applied two numeric models, The Green Screen for Safer Chemicals™ and the Toxic Potential Indicator. To improve the sensitivity of the model outputs, we developed a novel, life cycle thinking based hazard assessment method that facilitates the projection of hazards throughout material life cycles. Our results show that the least hazardous CIGS solar cell device and manufacturing protocol consist of a titanium substrate, molybdenum metal back electrode, CuInS{sub 2} p-type absorber deposited by spray pyrolysis, ZnS buffer deposited by spray ion layer gas reduction, ZnO:Ga transparent conducting oxide (TCO) deposited by sputtering, and the encapsulant polydimethylsiloxane.

A structure for models of hazardous materials with complex behavior

International Nuclear Information System (INIS)

Rodean, H.C.

1991-01-01

Most atmospheric dispersion models used to assess the environmental consequences of accidental releases of hazardous chemicals do not have the capability to simulate the pertinent chemical and physical processes associated with the release of the material and its mixing with the atmosphere. The purpose of this paper is to present a materials sub-model with the flexibility to simulate the chemical and physical behaviour of a variety of materials released into the atmosphere. The model, which is based on thermodynamic equilibrium, incorporates the ideal gas law, temperature-dependent vapor pressure equations, temperature-dependent dissociation reactions, and reactions with atmospheric water vapor. The model equations, written in terms of pressure ratios and dimensionless parameters, are used to construct equilibrium diagrams with temperature and the mass fraction of the material in the mixture as coordinates. The model's versatility is demonstrated by its application to the release of UF 6 and N 2 O 4 , two materials with very different physical and chemical properties. (author)

Hazardous materials in aquatic environments of the Mississippi River Basin. Quarterly project status report, 1 April--30 June 1994

Energy Technology Data Exchange (ETDEWEB)

1994-08-01

This report contains a cluster of twenty separate project reports concerning the fate, environmental transport, and toxicity of hazardous wastes in the Mississippi River Basin. Some of topics investigated involve: biological uptake and metabolism; heavy metal immobilization; biological indicators; toxicity; and mathematical models.

Radiation hazards

International Nuclear Information System (INIS)

Rausch, L.

1979-01-01

On a scientific basis and with the aid of realistic examples, the author gives a popular introduction to an understanding and judgment of the public discussion over radiation hazards: Uses and hazards of X-ray examinations, biological radiation effects, civilisation risks in comparison, origins and explanation of radiation protection regulations. (orig.) [de

An examination of the Hazardous Materials Transportation Uniform Safety Act (HMTUSA): A southern perspective

International Nuclear Information System (INIS)

1992-03-01

On November 16,1990, President Bush signed into law the most comprehensive amendments to the Hazardous Materials Transportation Act (HMTA) in 15 years. The Hazardous Materials Transportation Uniform Safety Act of 1990 (HMTUSA) was created by Congress in an effort to strengthen and clarify the HMTA. This paper will discuss the act's provisions as they affect shipments of spent fuel and high-level radioactive materials as well as the impact of those provisions on routing and emergency response issues in the southern region. HMTUSA consists of seven key provisions that affect radioactive materials: clarification of regulatory jurisdiction; highway routing standards; broadened industry registration; safety permits for motor carriers of high risk materials; expanded nuclear transportation requirements; new provisions for emergency response training and planning; and a public process for assessing the feasibility of a federally operated central reporting system and data center. In addition to amending various HMTA provisions, the new HMTUSA act provides appropriations to carry out the specific goals of the legislation. The act authorizes appropriations for the 1991, 1992 and 1993 fiscal years

78 FR 22798 - Hazardous Materials: Revision of Maximum and Minimum Civil Penalties

Science.gov (United States)

2013-04-17

.... 5101 et seq.). Section 5123(a) of that law provides civil penalties for knowing violations of Federal... 107--Guidelines for Civil Penalties * * * * * IV. * * * C. * * * Under the Federal hazmat law, 49 U.S... Maximum and Minimum Civil Penalties AGENCY: Pipeline and Hazardous Materials Safety Administration (PHMSA...

Material Selection for Cable Gland to Improved Reliability of the High-hazard Industries

Science.gov (United States)

Vashchuk, S. P.; Slobodyan, S. M.; Deeva, V. S.; Vashchuk, D. S.

2018-01-01

The sealed cable glands (SCG) are available to ensure safest connection sheathed single wire for the hazard production facility (nuclear power plant and others) the same as pilot cable, control cables, radio-frequency cables et al. In this paper, we investigate the specifics of the material selection of SCG with the express aim of hazardous man-made facility. We discuss the safe working conditions for cable glands. The research indicates the sintering powdered metals cables provide the reliability growth due to their properties. A number of studies have demonstrated the verification of material selection. On the face of it, we make findings indicating that double glazed sealed units could enhance reliability. We had evaluated sample reliability under fire conditions, seismic load, and pressure containment failure. We used the samples mineral insulated thermocouple cable.

Factors associated with occupational exposure to biological material among nursing professionals.

Science.gov (United States)

Negrinho, Nádia Bruna da Silva; Malaguti-Toffano, Silmara Elaine; Reis, Renata Karina; Pereira, Fernanda Maria Vieira; Gir, Elucir

2017-01-01

to identify factors associated with occupational exposure to biological material among nursing professionals. a cross-sectional study was conducted in a high complexity hospital of a city in the state of São Paulo, Brazil. Nursing professionals were interviewed from March to November 2015. All ethical aspects were observed. among the 226 professionals interviewed, 17.3% suffered occupational exposure to potentially contaminated biological material, with 61.5% being percutaneous. Factors such as age (p=0.003), professional experience in nursing (p=0.015), and experience at the institution (p=0.032) were associated with the accidents with biological material. most accidents with biological material among nursing professionals were percutaneous. Age, professional experience, and experience at the institution were considered factors associated with occupational exposure.

Occupational accidents involving biological material among public health workers.

Science.gov (United States)

Chiodi, Mônica Bonagamba; Marziale, Maria Helena Palucci; Robazzi, Maria Lúcia do Carmo Cruz

2007-01-01

This descriptive research aimed to recognize the occurrence of work accidents (WA) involving exposure to biological material among health workers at Public Health Units in Ribeirão Preto-SP, Brazil. A quantitative approach was adopted. In 2004, 155 accidents were notified by means of the Work Accident Communication (WAC). Sixty-two accidents (40%) involved exposure to biological material that could cause infections like Hepatitis and Aids. The highest number of victims (42 accidents) came from the category of nursing aids and technicians. Needles were responsible for 80.6% of accidents and blood was the biological material involved in a majority of occupational exposure cases. This subject needs greater attention, so that prevention measures can be implemented, which consider the peculiarities of the activities carried out by the different professional categories.

Materials Manufactured from 3D Printed Synthetic Biology Arrays

Science.gov (United States)

Gentry, Diana; Micks, Ashley

2013-01-01

Many complex, biologically-derived materials have extremely useful properties (think wood or silk), but are unsuitable for space-related applications due to production, manufacturing, or processing limitations. Large-scale ecosystem-based production, such as raising and harvesting trees for wood, is impractical in a self-contained habitat such as a space station or potential Mars colony. Manufacturing requirements, such as the specialized equipment needed to harvest and process cotton, add too much upmass for current launch technology. Cells in nature are already highly specialized for making complex biological materials on a micro scale. We envision combining these strengths with the recently emergent technologies of synthetic biology and 3D printing to create 3D-structured arrays of cells that are bioengineered to secrete different materials in a specified three-dimensional pattern.

EFSA BIOHAZ Panel (EFSA Panel on Biological Hazards, 2013. Scientific Opinion on the public health hazards to be covered by inspection of meat from sheep and goats

DEFF Research Database (Denmark)

Hald, Tine; Baggesen, Dorte Lau

A risk ranking process identified Toxoplasma gondii and pathogenic verocytotoxin-producing Escherichia coli (VTEC) as the most relevant biological hazards for meat inspection of sheep and goats. As these are not detected by traditional meat inspection, a meat safety assurance system using risk......-based interventions was proposed. Further studies are required on T. gondii and pathogenic VTEC. If new information confirms these hazards as a high risk to public health from meat from sheep or goats, setting targets at carcass level should be considered. Other elements of the system are risk...... the extensive production systems used, and the ranking of chemical substances, which should be regularly updated and include new hazards. Control programmes across the food chain, national residue control plans, feed control and monitoring of environmental contaminants should be better integrated. Meat...

Decision Support for Environmental Management of Industrial Non-Hazardous Secondary Materials: New Analytical Methods Combined with Simulation and Optimization Modeling

Science.gov (United States)

Non-hazardous solid materials from industrial processes, once regarded as waste and disposed in landfills, offer numerous environmental and economic advantages when put to beneficial uses (BUs). Proper management of these industrial non-hazardous secondary materials (INSM) requir...

Conceptual design report, Hazardous Materials Management and Emergency Response (HAMMER) Training Center

Energy Technology Data Exchange (ETDEWEB)

Kelly, K.E. [Westinghouse Hanford Co., Richland, WA (United States)

1994-11-09

For the next 30 years, the main activities at the US Department of Energy (DOE) Hanford Site will involve the management, handling, and cleanup of toxic substances. If the DOE is to meet its high standards of safety, the thousands of workers involved in these activities will need systematic training appropriate to their tasks and the risks associated with these tasks. Furthermore, emergency response for DOE shipments is the primary responsibility of state, tribal, and local governments. A collaborative training initiative with the DOE will strengthen emergency response at the Hanford Site and within the regional communities. Local and international labor has joined the Hazardous Materials Management and Emergency Response (HAMMER) partnership, and will share in the HAMMER Training Center core programs and facilities using their own specialized trainers and training programs. The HAMMER Training Center will provide a centralized regional site dedicated to the training of hazardous material, emergency response, and fire fighting personnel.

Conceptual design report, Hazardous Materials Management and Emergency Response (HAMMER) Training Center

International Nuclear Information System (INIS)

Kelly, K.E.

1994-01-01

For the next 30 years, the main activities at the US Department of Energy (DOE) Hanford Site will involve the management, handling, and cleanup of toxic substances. If the DOE is to meet its high standards of safety, the thousands of workers involved in these activities will need systematic training appropriate to their tasks and the risks associated with these tasks. Furthermore, emergency response for DOE shipments is the primary responsibility of state, tribal, and local governments. A collaborative training initiative with the DOE will strengthen emergency response at the Hanford Site and within the regional communities. Local and international labor has joined the Hazardous Materials Management and Emergency Response (HAMMER) partnership, and will share in the HAMMER Training Center core programs and facilities using their own specialized trainers and training programs. The HAMMER Training Center will provide a centralized regional site dedicated to the training of hazardous material, emergency response, and fire fighting personnel

Notification: Audit of Security Categorization for EPA Systems That Handle Hazardous Material Information

Science.gov (United States)

Project #OA-FY18-0089, January 8, 2018. The OIG plans to begin preliminary research to determine whether the EPA classified the sensitivity of data for systems that handle hazardous waste material information as prescribed by NIST.

Truck shipment risks for assessing hazardous materials - a new paradigm incorporating safety and security

Energy Technology Data Exchange (ETDEWEB)

Greenberg, A.; McSweeney, T.; Allen, J.; Lepofsky, M. [Battelle Memorial Inst., Columbus, OH (United States); Abkowitz, M. [Dept. of Civil Engineering, Vanderbilt Univ., Nashville, TN (United States)

2004-07-01

Recent terrorist events, most notably September 11, 2001, have taught us that transportation risk management must be performed with a different lens to accommodate terrorism scenarios that would have previously been considered unlikely to warrant serious attention. Given these circumstances, a new paradigm is needed for managing the risks associated with highway transport of hazardous materials. In particular, this paradigm must: 1) more explicitly consider security threat and vulnerability, and 2) integrate security considerations into an overall framework for addressing natural and man-made disasters, be they accidental or planned. This paper summarizes the results of a study sponsored by the U.S. Department of Transportation, Federal Motor Carrier Safety Administration for the purpose of exploring how a paradigm might evolve in which both safety and security risks can be evaluated as a systematic, integrated process. The work was directed at developing a methodology for assessing the impacts of hazardous materials safety and security incident consequences when transported by highway. This included consideration of the manner in which these materials could be involved in initiating events as well as potential outcomes under a variety of release conditions. The methodology is subsequently applied to various classes of hazardous materials to establish an economic profile of the impacts that might be expected if a major release were to occur. The paper concludes with a discussion of the findings and implications associated with this effort.

Truck shipment risks for assessing hazardous materials - a new paradigm incorporating safety and security

International Nuclear Information System (INIS)

Greenberg, A.; McSweeney, T.; Allen, J.; Lepofsky, M.; Abkowitz, M.

2004-01-01

Recent terrorist events, most notably September 11, 2001, have taught us that transportation risk management must be performed with a different lens to accommodate terrorism scenarios that would have previously been considered unlikely to warrant serious attention. Given these circumstances, a new paradigm is needed for managing the risks associated with highway transport of hazardous materials. In particular, this paradigm must: 1) more explicitly consider security threat and vulnerability, and 2) integrate security considerations into an overall framework for addressing natural and man-made disasters, be they accidental or planned. This paper summarizes the results of a study sponsored by the U.S. Department of Transportation, Federal Motor Carrier Safety Administration for the purpose of exploring how a paradigm might evolve in which both safety and security risks can be evaluated as a systematic, integrated process. The work was directed at developing a methodology for assessing the impacts of hazardous materials safety and security incident consequences when transported by highway. This included consideration of the manner in which these materials could be involved in initiating events as well as potential outcomes under a variety of release conditions. The methodology is subsequently applied to various classes of hazardous materials to establish an economic profile of the impacts that might be expected if a major release were to occur. The paper concludes with a discussion of the findings and implications associated with this effort

75 FR 6348 - Deposit of Biological Materials

Science.gov (United States)

2010-02-09

... either directly or indirectly. When the invention involves a biological material, sometimes words alone... charge about the same rates for their services. For example, the American Type Culture Collection (ATCC...

Expert geographical information system for assessing hazardous materials in aquatic environments

International Nuclear Information System (INIS)

Regens, J.L.; White, L.; Wright, J.D.; Rene, A.; Mielke, H.; Bakeer, R.; Belkhouche, B.; Barber, M.

1993-01-01

Hazardous substances, including radionuclides, heavy metals, chlorinated hydrocarbons, and industrial solvents, pose unique challenges in terms of environmental restoration and waste management, especially in aquatic environments. When stored, used or disposed of improperly, hazardous materials including transuranic wastes, high level wastes, low level wastes, greater than class C wastes, mixed wastes or chemical wastes can contaminate an array of environmental receptors ranging from soils, sediments, groundwater to surface water. Depending on the specific hazardous substance and site attributes, environmental restoration and waste management can be a complex, problematic activity. This is particularly true for the major Defense Programs facilities managed by the Department of Energy (DOE). This research cluster consists of two discrete elements. Project Element No. 1 develops and applies GIS-based approaches to decision support for environmental restoration by delineating potential exposures and health risks at the Rocky Flats Plant and profiling contemporary and historical demographic/land use patterns at Sandia National Laboratories. Project Element No. 2 develops ESS software for surface water and ground water contaminants in the Mississippi River Basin

Understanding and managing the movements of hazardous material shipments through Texas population centers.

Science.gov (United States)

2009-08-01

Every day almost a million shipments of hazardous materials move safely and securely along our nations transportation system, via any combination of modes. Only a small fraction of total shipments interrupt their planned journey due to an incident...

Application of United States Department of Transportation regulations to hazardous material and waste shipments on the Hanford site

International Nuclear Information System (INIS)

Burnside, M.E.

1992-01-01

All hazardous material and waste transported over roadways open to the public must be in compliance with the U.S. Department of Transportation (DOT) regulations. The DOT states that the hazardous material regulations (HMR) also apply to government-owned, contractor-operated (GOCO) transportation operations over any U.S. Department of Energy (DOE) site roadway where the public has free and unrestricted access. Hazardous material and waste in packages that do not meet DOT regulations must be transported on DOE site roadways in a manner that excludes the public and nonessential workers. At the DOE Richland Field Office (the Hanford Site), hazardous material and waste movements that do not meet DOT requirements are transported over public access roadways during off-peak hours with the roadways barricaded. These movements are accomplished using a transportation plan that involves the DOE, DOE contractors, and private utilities who operate on or near the Hanford Site. This method, which is used at the Hanford Site to comply with DOT regulations onsite, can be communicated to other DOE sites to provide a basis for achieving consistency in similar transportation operations. (author)

Magnetically responsive biological materials and their applications

Czech Academy of Sciences Publication Activity Database

Šafařík, Ivo; Pospíšková, K.; Baldíková, E.; Šafaříková, Miroslava

2016-01-01

Roč. 7, č. 4 (2016), s. 254-261 ISSN 0976-3961 Institutional support: RVO:60077344 Keywords : adsorbents * biological materials * carriers * magnetic modification * whole-cell biocatalyst Subject RIV: EI - Biotechnology ; Bionics

A multisignal detection of hazardous materials for homeland security

Directory of Open Access Journals (Sweden)

Alamaniotis Miltiadis

2009-01-01

Full Text Available The detection of hazardous materials has been identified as one of the most urgent needs of homeland security, especially in scanning cargo containers at United States ports. To date, special nuclear materials have been detected using neutron or gamma interrogation, and recently the nuclear resonance fluorescence has been suggested. We show a new paradigm in detecting the materials of interest by a method that combines four signals (radiography/computer tomography, acoustic, muon scattering, and nuclear resonance fluorescence in cargos. The intelligent decision making software system is developed to support the following scenario: initially, radiography or the computer tomography scan is constructed to possibly mark the region(s of interest. The acoustic interrogation is utilized in synergy to obtain information regarding the ultrasonic velocity of the cargo interior. The superposition of the computer tomography and acoustic images narrows down the region(s of interest, and the intelligent system guides the detection to the next stage: no threat and finish, or proceed to the next interrogation. If the choice is the latter, knowing that high Z materials yield large scattering angle for muons, the muon scattering spectrum is used to detect the existence of such materials in the cargo. Additionally, the nuclear resonance fluorescence scan yields a spectrum that can be likened to the fingerprint of a material. The proposed algorithm is tested for detection of special nuclear materials in a comprehensive scenario.

A multisignal detection of hazardous materials for homeland security

International Nuclear Information System (INIS)

Alamaniotis, M.; Terrill, S.; Perry, J.; Gao, R.; Tsoukalas, L.; Jevremovic, T.

2009-01-01

The detection of hazardous materials has been identified as one of the most urgent needs of homeland security, especially in scanning cargo containers at United States ports. To date, special nuclear materials have been detected using neutron or gamma interrogation, and recently the nuclear resonance fluorescence has been suggested. We show a new paradigm in detecting the materials of interest by a method that combines four signals (radiography/computer tomography, acoustic, muon scattering, and nuclear resonance fluorescence) in cargos. The intelligent decision making software system is developed to support the following scenario: initially, radiography or the computer tomography scan is constructed to possibly mark the region(s) of interest. The acoustic interrogation is utilized in synergy to obtain information regarding the ultrasonic velocity of the cargo interior. The superposition of the computer tomography and acoustic images narrows down the region(s) of interest, and the intelligent system guides the detection to the next stage: no threat and finish, or proceed to the next interrogation. If the choice is the latter, knowing that high Z materials yield large scattering angle for muons, the muon scattering spectrum is used to detect the existence of such materials in the cargo. Additionally, the nuclear resonance fluorescence scan yields a spectrum that can be likened to the fingerprint of a material. The proposed algorithm is tested for detection of special nuclear materials in a comprehensive scenario. (author)

Automating Risk Assessments of Hazardous Material Shipments for Transportation Routes and Mode Selection

International Nuclear Information System (INIS)

Dolphin, Barbara H.; Richins, William D.; Novascone, Stephen R.

2010-01-01

The METEOR project at Idaho National Laboratory (INL) successfully addresses the difficult problem in risk assessment analyses of combining the results from bounding deterministic simulation results with probabilistic (Monte Carlo) risk assessment techniques. This paper describes a software suite designed to perform sensitivity and cost/benefit analyses on selected transportation routes and vehicles to minimize risk associated with the shipment of hazardous materials. METEOR uses Monte Carlo techniques to estimate the probability of an accidental release of a hazardous substance along a proposed transportation route. A METEOR user selects the mode of transportation, origin and destination points, and charts the route using interactive graphics. Inputs to METEOR (many selections built in) include crash rates for the specific aircraft, soil/rock type and population densities over the proposed route, and bounding limits for potential accident types (velocity, temperature, etc.). New vehicle, materials, and location data are added when available. If the risk estimates are unacceptable, the risks associated with alternate transportation modes or routes can be quickly evaluated and compared. Systematic optimizing methods will provide the user with the route and vehicle selection identified with the lowest risk of hazardous material release. The effects of a selected range of potential accidents such as vehicle impact, fire, fuel explosions, excessive containment pressure, flooding, etc. are evaluated primarily using hydrocodes capable of accurately simulating the material response of critical containment components. Bounding conditions that represent credible accidents (i.e; for an impact event, velocity, orientations, and soil conditions) are used as input parameters to the hydrocode models yielding correlation functions relating accident parameters to component damage. The Monte Carlo algorithms use random number generators to make selections at the various decision

Hazardous materials incidents on major highways -- A case study

International Nuclear Information System (INIS)

McElhaney, M.S.

1995-01-01

Personnel from both the public and private sectors have been involved for many years in pre-planning for hazardous materials releases at fixed installations all over the world. As a result of several major petroleum releases during marine transportation, oil companies, private contractors and government agencies have been preparing contingency plans for oil spills and other petroleum product releases in marine settings. Various industry groups have also developed plans for railway and pipeline disasters. These response plans are of varying quality, complexity and usefulness. Organizations such as plant emergency response teams, government agencies, contract response and clean-up crews and fire departments use these plans as a basis for training and resource allocation, hopefully becoming familiar enough with them that the plans are truly useful when product releases occur. Planners and emergency responders to hazardous materials releases must overcome some of the deficiencies which have long stood in the way of efficient and effective response and mitigation efforts. Specifically they must recognize and involve all resources with which they may respond or interact during an incident. This involvement should begin with the planning stages and carry through to training and emergency response and recovery efforts. They must ensure that they adopt and utilize a common command and control system and that all potential resources know this system thoroughly and train together before the incident occurs. It is only through incorporating these two factors that may successfully combat the ever growing number of unwanted product releases occurring in the more difficult realm of transportation

Criticality analysis for hazardous materials transportation; Classificacao da criticidade das rotas do transporte rodoviario de produtos perigosos da BRASKEM

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Katia; Brady, Mariana [Det Norske Veritas (DNV), Rio de Janeiro, RJ (Brazil); Diniz, Americo [BRASKEM S.A., Sao Paulo, SP (Brazil)

2008-07-01

The bad conditions of Brazilians roads drive the companies to be more exigent with the transportation of hazardous materials to avoid accidents or materials releases with actions to contain the releases to community and water sources. To minimize this situation, DNV and BRASKEM developed a methodology for risk analysis called Criticality Analysis for Hazardous Materials Transportation. The objective of this methodology is identifying the most critical points of routes to make actions to avoid accidents. (author)

Nanomechanical strength mechanisms of hierarchical biological materials and tissues.

Science.gov (United States)

Buehler, Markus J; Ackbarow, Theodor

2008-12-01

Biological protein materials (BPMs), intriguing hierarchical structures formed by assembly of chemical building blocks, are crucial for critical functions of life. The structural details of BPMs are fascinating: They represent a combination of universally found motifs such as alpha-helices or beta-sheets with highly adapted protein structures such as cytoskeletal networks or spider silk nanocomposites. BPMs combine properties like strength and robustness, self-healing ability, adaptability, changeability, evolvability and others into multi-functional materials at a level unmatched in synthetic materials. The ability to achieve these properties depends critically on the particular traits of these materials, first and foremost their hierarchical architecture and seamless integration of material and structure, from nano to macro. Here, we provide a brief review of this field and outline new research directions, along with a review of recent research results in the development of structure-property relationships of biological protein materials exemplified in a study of vimentin intermediate filaments.

Sanitary Assessment of Hazardous Materials Exposed To Highly Toxic Chemical Compounds

International Nuclear Information System (INIS)

Rembovskiy, V.; Ermolaeva, E.

2007-01-01

Industrial or terroristic accidents in which toxic chemicals (TC) are the main or attendant damaging factors should be regarded as a new challenge for experts, because of little knowledge on the methodology to estimating the long-term risk for humans due to contamination of the building materials and environment. In the Russian Federation, there appeared to be a kind of model systems for developing an algorithm for solving these or similar problems. Under dismantling and liquidation of the former facilities for chemical weapon production (FCWP) the building materials are regarded as potential waste products the fate of which (processing, warehousing, utilization, and destruction) is dependent on their possible hazard for human population and environment. The standard approaches for hazard assessment of waste products of the FCWP turned out to be insufficient. When conducting the present work, the following problems have been solved: 1. Selection of representative samples taking into consideration a diversity of construction materials, great quantities of potentially toxic waste materials, information on the production conditions, breakdowns in the process of production, accidents, composition of the decontaminators used, decontamination frequency, etc. 2. Analysis of TC in composite matrixes complicated by the following problems: extraction, masking effects of concomitant components during indirect analysis, lack of certified methods of direct analysis of TC, discrepancy of results of GC and direct GCMS analysis, low sensitivity of GCMS analysis, big volume of samples (more than 0.5 kg), heterogeneity of physical-chemical properties of different matrixes influencing the process of degradation of TC. 3. Hazard assessment of the wastes in toxic-and-sanitary experiment relying on non-specific signs of intoxication due to relatively low percentage of TC and masking effects of various matrix components. Application of the integral toxicity tests with soil

Hazardous materials transportation. Part 2. Radioactive materials and wastes (citations from the NTIS Data Base). Final report for 1964--March 1978

International Nuclear Information System (INIS)

Reimherr, G.W.

1978-06-01

The bibliography cites studies on the hazards, risks, and uncertainty of transporting radioactive wastes and materials. The design of shipping containers and special labels for identification purposes for transporting fuels and wastes are also cited. Studies are included on legislation dealing with the safety and health of the population and the environmental problems associated with transporting radioactive materials

41 CFR 101-42.1101 - Federal supply classification (FSC) groups and classes which contain hazardous materials.

Science.gov (United States)

2010-07-01

..., building paper, and thermal insulation materials Asbestos cloth which has loose fibers or particles that... shipment. 5965 Headsets, handsets, microphones, and speakers Items containing magnetic material. 5970... hazardous chemicals, solvents. 6625 Electrical and electronic properties measuring and testing instruments...

Advanced Materials Laboratory hazards assessment document

Energy Technology Data Exchange (ETDEWEB)

Barnett, B.; Banda, Z.

1995-10-01

The Department of Energy Order 55OO.3A requires facility-specific hazards assessments be prepared, maintained, and used for emergency planning purposes. This hazards assessment document describes the chemical and radiological hazards associated with the AML. The entire inventory was screened according to the potential airborne impact to onsite and offsite individuals. The air dispersion model, ALOHA, estimated pollutant concentrations downwind from the source of a release, taking into consideration the toxicological and physical characteristics of the release site, the atmospheric conditions, and the circumstances of the release. The greatest distance at which a postulated facility event will produce consequences exceeding the Early Severe Health Effects threshold is 23 meters. The highest emergency classification is a General Emergency. The Emergency Planning Zone is a nominal area that conforms to DOE boundaries and physical/jurisdictional boundaries such as fence lines and streets.

Musculoskeletal symptoms and ergonomic hazards among material handlers in grocery retail industries

Science.gov (United States)

Nasrull Abdol Rahman, Mohd; Zuhaidi, Muhammad Fareez Ahmad

2017-08-01

Grocery retail work can be physically demanding as material handler’s tasks involve manual lifting, lowering, carrying, pushing and pulling loads. The nature of this work puts them at a risk for serious low back pain, shoulder pain and other musculoskeletal injuries. This study was conducted by using two different types of tools which were Nordic Musculoskeletal Questionnaire (NMQ) as a survey and Washington Industrial Safety and Health Act (WISHA) Checklist as a direct observation method. Among 46 males and 14 females material handlers were involved throughout this study. For NMQ, the highest body part trouble in the last 12 months was low back pain (88.3%), followed by upper back (68.3%), neck (55.3%) and shoulder (36.7%). While for WISHA Checklist, most of them experienced hazard level involving awkward posture and high hand force. From the research conducted, musculoskeletal disorders (MSDs) and ergonomic risk factors (ERFs) do related as it showed that musculoskeletal disorders may arise if the workers ignored the safety in ergonomic hazards.

Biogeosystem technique as a method to overcome the Biological and Environmental Hazards of modern Agricultural, Irrigational and Technological Activities

Science.gov (United States)

Kalinitchenko, Valery; Batukaev, Abdulmalik; Zinchenko, Vladimir; Zarmaev, Ali; Magomadov, Ali; Chernenko, Vladimir; Startsev, Viktor; Bakoev, Serojdin; Dikaev, Zaurbek

2014-05-01

Modern challenge for humanity is to replace the paradigm of nature use and overcome environmental hazards of agronomy, irrigation, industry, and other human activities in biosphere. It is utterly reasonable to stop dividing biosphere on shares - the human habitat and the environment. In the 21st century it is an outdated anthropocentrism. Contradicting himself to biosphere Humankind has the problems. The new paradigm of biosphere control by methods of Biogeosystem technique is on agenda of Humankind. Key directions of Biogeosystem technique. Tillage. Single rotary milling 20…30-50…60 sm soil layer optimizes the evolution and environment of soil, creates a favorable conditions for the rhizosphere, increases the biological productivity of biosphere by 30-50% compared to the standard agricultural practices for the period up to 40 years. Recycle material. Recycling of mineral and organic substances in soil layer of 20…30-50…60 sm in rotary milling soil processing provides wastes clean return to biosphere. Direct intrasoil substances synthesis. Environmentally friendly robot wasteless nanotechnology provides direct substances synthesis, including fertilizers, inside the soil. It eliminates the prerequisites of the wastes formation under standard industrial technologies. Selective substance's extraction from soil. Electrochemical robotic nanotechnology provides selective substances extraction from soil. The technology provides recovery, collection and subsequent safe industrial use of extracted substances out of landscape. Saving fresh water. An important task is to save fresh water in biosphere. Irrigation spends water 4-5 times more of biological requirements of plants, leads to degradation of soil and landscape. The intrasoil pulse continuous-discrete paradigm of irrigation is proposed. It provides the soil and landscape conservation, increases the biological productivity, save the fresh water up to 10-20 times. The subsurface soil rotary processing and

Statistical treatment of hazards result from radioactive material in metal scrap

International Nuclear Information System (INIS)

Salem, E.F.; Rashad, S.M.

2013-01-01

Radioactive sources have a wide range of uses in medicine and industry. Radioactive materials entering the public domain in an uncontrolled manner may creating a serious risk of radiation exposure for workers and the public as well as excessive costs for plant decontamination and waste of product to be borne by the metal industry. This paper describes the major accidents that had happened in the last decades due to radioactive material in metal scrap, provides assessment of associated hazards and lessons learned. This will help Regulatory Authority to introduce measures capable to avoid the recurrence of similar events. The study highlights the situation for metal scrap incidents in Egypt.

NBS activities in biological reference materials

Energy Technology Data Exchange (ETDEWEB)

Rasberry, S.D.

1988-12-01

NBS activities in biological reference materials during 1986-1988 are described with a preview of plans for future certifications of reference materials. During the period, work has been completed or partially completed on about 40 reference materials of importance to health, nutrition, and environmental quality. Some of the reference materials that have been completed during the period and are described include: creatinine (SRM 914a), bovine serum albumin (SRM 927a), cholesterol in human serum (SRM's 1951-1952), aspartate aminotransferase (RM 8430), cholesterol and fat-soluble vitamins in coconut oil (SRM 1563), wheat flour (SRM 1567a), rice flour (SRM 1568a), mixed diet (RM 8431a), dinitropyrene isomers and 1-nitropyrene (SRM 1596), and complex PAH's from coal tar (SRM 1597). Oyster tissue (SRM 1566a) is being analyzed and should be available in 1988.

Flow evaluation of the leaching hazardous materials from spent nickel-cadmium batteries discarded in different water surroundings.

Science.gov (United States)

Guo, Xingmei; Song, Yan; Nan, Junmin

2018-02-01

The leaching characteristics of hazardous materials from Ni-Cd batteries immersed in four typical water samples, i.e., water with NaCl, river water, tap water, and deionized water, were investigated to evaluate the potential environmental harm of spent Ni-Cd batteries in the water surroundings. It is shown that four water surroundings all could leach hazardous materials from the Ni-Cd batteries. The water with NaCl concentration of 66.7 mg L -1 had the highest leaching ability, the hazardous materials were leached after only approximately 50 days (average time, with a standard deviation of 4.1), while less than 100 days were needed in the others. An electrochemical corrosion is considered to be the main leaching mechanism leading to battery breakage, while the dissolution-deposition process and the powder route result in the leakage and transference of nickel and cadmium materials from the electrodes. The anions, i.e., SO 4 2- and Cl - , and dissolved oxygen in water were demonstrated to be the vital factors that influence the leaching processes. Thus, it is proposed that spent Ni-Cd batteries must be treated properly to avoid potential danger to the environment.

Study of biocompatible and biological materials

CERN Document Server

Pecheva, Emilia

2017-01-01

The book gives an overview on biomineralization, biological, biocompatible and biomimetic materials. It reveals the use of biomaterials alone or in composites, how their performance can be improved by tailoring their surface properties by external factors and how standard surface modification techniques can be applied in the area of biomaterials to beneficially influence their growth on surfaces.

Survey of currently available reference materials for use in connection with the determination of trace elements in biological materials

International Nuclear Information System (INIS)

Parr, R.M.

1983-09-01

Elemental analysis of biological materials is at present the subject of intensive study by many different research groups throughout the world, in view of the importance of these trace elements in health and medical diagnosis. IAEA and other organizations are now making a variety of suitable reference materials available for use in connection with the determination of trace elements in biological materials. To help analysts in making a selection from among these various materials, the present report provides a brief survey of data for all such biological reference materials known to the author. These data are compiled by the author from January 1982 to June 1983

Assessment of natural radioactivity and associated radiation hazards in some Cameroonian building materials

International Nuclear Information System (INIS)

Ngachin, M.; Garavaglia, M.; Giovani, C.; Kwato Njock, M.G.; Nourreddine, A.

2007-01-01

The concentration of 238 U, 232 Th and 40 K in 13 building materials obtained from factories and collected in field in Cameroon were investigated by γ-ray spectrometry. The activity ranged from 1.76 to 49.84Bqkg -1 , 0.32 to 147Bqkg -1 and 18 to 1226Bqkg -1 for 238 U, 232 Th and 40 K, respectively. The highest 238 U activity was found in compressed red soil brick type I (49.6+/-0.3Bqkg -1 ) produced by a local manufacturer while the highest 232 Th (139+/-13Bqkg -1 ) and 40 K (1162+/-108Bqkg -1 ) activities were found in gravel collected from an exploitation site in Logbadjeck. The activities are compared with available data from other investigations and with the world average value for soils. The radium equivalent activity Ra eq , the external hazard index H ex , the indoor absorbed dose rate D-bar in air and the annual effective dose equivalent E-bar were evaluated to assess the radiation hazard for people living in dwellings made of the materials studied. All building materials have shown Ra eq (range from 10 to 313Bqkg -1 ) lower than the limit of 370Bqkg -1 set in the Organization for Economic Cooperation and Development [OECD, 1979. Exposure to radiation from the natural radioactivity in building materials. OECD, Paris] report which is equivalent to a γ-dose of 1.5mSvyr -1 . Except for the gravel from Logbadjeck, all the materials examined are acceptable for use as building materials as defined by the OECD criterion

Membrane materials for storing biological samples intended for comparative nanotoxicological testing

Science.gov (United States)

Metelkin, A.; Kuznetsov, D.; Kolesnikov, E.; Chuprunov, K.; Kondakov, S.; Osipov, A.; Samsonova, J.

2015-11-01

The study is aimed at identifying the samples of most promising membrane materials for storing dry specimens of biological fluids (Dried Blood Spots, DBS technology). Existing sampling systems using cellulose fiber filter paper have a number of drawbacks such as uneven distribution of the sample spot, dependence of the spot spreading area on the individual biosample properties, incomplete washing-off of the sample due to partially inconvertible sorption of blood components on cellulose fibers, etc. Samples of membrane materials based on cellulose, polymers and glass fiber with applied biosamples were studied using methods of scanning electron microscopy, FT-IR spectroscopy and surface-wetting measurement. It was discovered that cellulose-based membrane materials sorb components of biological fluids inside their structure, while membranes based on glass fiber display almost no interaction with the samples and biological fluid components dry to films in the membrane pores between the structural fibers. This characteristic, together with the fact that membrane materials based on glass fiber possess sufficient strength, high wetting properties and good storage capacity, attests them as promising material for dry samples of biological fluids storage systems.

Membrane materials for storing biological samples intended for comparative nanotoxicological testing

International Nuclear Information System (INIS)

Metelkin, A; Kuznetsov, D; Kolesnikov, E; Chuprunov, K; Kondakov, S; Osipov, A; Samsonova, J

2015-01-01

The study is aimed at identifying the samples of most promising membrane materials for storing dry specimens of biological fluids (Dried Blood Spots, DBS technology). Existing sampling systems using cellulose fiber filter paper have a number of drawbacks such as uneven distribution of the sample spot, dependence of the spot spreading area on the individual biosample properties, incomplete washing-off of the sample due to partially inconvertible sorption of blood components on cellulose fibers, etc. Samples of membrane materials based on cellulose, polymers and glass fiber with applied biosamples were studied using methods of scanning electron microscopy, FT-IR spectroscopy and surface-wetting measurement. It was discovered that cellulose-based membrane materials sorb components of biological fluids inside their structure, while membranes based on glass fiber display almost no interaction with the samples and biological fluid components dry to films in the membrane pores between the structural fibers. This characteristic, together with the fact that membrane materials based on glass fiber possess sufficient strength, high wetting properties and good storage capacity, attests them as promising material for dry samples of biological fluids storage systems. (paper)

Moessbauer spectroscopic studies of magnetically ordered biological materials

International Nuclear Information System (INIS)

Dickson, D.P.E.

1987-01-01

This paper discusses recent work showing the application of Moessbauer spectroscopy to the study of the properties of the magnetically ordered materials which occur in a variety of biological systems. These materials display a diversity of behaviour which provides good examples of the various possibilities which can arise with iron-containing particles of different compositions and sizes. (orig.)

Processing of hazardous material, or damage treatment method for shallow layer underground storage structure

International Nuclear Information System (INIS)

Ito, Hiroshi; Sakaguchi, Takehiko; Nishioka, Yoshihiro.

1997-01-01

In radioactive waste processing facilities and shallow layer underground structures for processing hazardous materials, sheet piles having freezing pipes at the joint portions are spiked into soils at the periphery of a damaged portion of the shallow layer underground structure for processing or storing hazardous materials. Liquid nitrogen is injected to the freezing pipes to freeze the joint portions of adjacent sheet piles. With such procedures, continuous waterproof walls are formed surrounding the soils at the peripheries of the damaged portion. Further, freezing pipes are disposed in the surrounding soils, and liquid nitrogen is injected to freeze the soils. The frozen soils are removed, and artificial foundation materials are filled in the space except for the peripheries of the damaged portion after the removal thereof, and liquid suspension is filled in the peripheries of the damaged portion, and restoration steps for closing the damaged portion are applied. Then, the peripheries of the damaged portion are buried again. With such procedures, series of treatments for removing contaminated soils and repairing a damaged portion can be conducted efficiently at a low cost. (T.M.)

Handbook of hazardous waste management

International Nuclear Information System (INIS)

Metry, A.A.

1980-01-01

The contents of this work are arranged so as to give the reader a detailed understanding of the elements of hazardous waste management. Generalized management concepts are covered in Chapters 1 through 5 which are entitled: Introduction, Regulations Affecting Hazardous Waste Management, Comprehensive Hazardous Waste Management, Control of Hazardous Waste Transportation, and Emergency Hazardous Waste Management. Chapters 6 through 11 deal with treatment concepts and are entitled: General Considerations for Hazardous Waste Management Facilities, Physical Treatment of Hazardous Wastes, Chemical Treatment of Hazardous Wastes, Biological Treatment of Hazardous Wastes, Incineration of Hazardous Wastes, and Hazardous Waste Management of Selected Industries. Chapters 12 through 15 are devoted to ultimate disposal concepts and are entitled: Land Disposal Facilities, Ocean Dumping of Hazardous Wastes, Disposal of Extremely Hazardous Wastes, and Generalized Criteria for Hazardous Waste Management Facilities

Method for decreasing radiation hazard in transporting radioactive material

International Nuclear Information System (INIS)

Wodrich, D.D.

1975-01-01

At the end of their useful life, fuel rods are removed from a nuclear reactor and transferred underwater into a shipping cask. The water in the pool of the nuclear reactor system (or fuels reprocessing plant) may contain troublesome amounts of radioactive isotopes, creating biological hazards for any shipping cask unless adequately cleaned after contacting pool water. Potential contamination of substantially all of the entire exterior of the shipping cask is avoided because such shipping cask is at least predominantly immersed in fresh water within a vertically shiftable container which can be, for example, shifted between the bottom and the surface of the pool. Fresh water is supplied to the interior of the shiftable container whereby substantially all of the exterior of the shipping cask is immersed in fresh water, maintained at a pressure and/or flow velocity preventing the pool water from contacting the exterior of the shipping cask

Invited review liquid crystal models of biological materials and silk spinning.

Science.gov (United States)

Rey, Alejandro D; Herrera-Valencia, Edtson E

2012-06-01

A review of thermodynamic, materials science, and rheological liquid crystal models is presented and applied to a wide range of biological liquid crystals, including helicoidal plywoods, biopolymer solutions, and in vivo liquid crystals. The distinguishing characteristics of liquid crystals (self-assembly, packing, defects, functionalities, processability) are discussed in relation to biological materials and the strong correspondence between different synthetic and biological materials is established. Biological polymer processing based on liquid crystalline precursors includes viscoelastic flow to form and shape fibers. Viscoelastic models for nematic and chiral nematics are reviewed and discussed in terms of key parameters that facilitate understanding and quantitative information from optical textures and rheometers. It is shown that viscoelastic modeling the silk spinning process using liquid crystal theories sheds light on textural transitions in the duct of spiders and silk worms as well as on tactoidal drops and interfacial structures. The range and consistency of the predictions demonstrates that the use of mesoscopic liquid crystal models is another tool to develop the science and biomimetic applications of mesogenic biological soft matter. Copyright © 2011 Wiley Periodicals, Inc.

Strategy on biological evaluation for biodegradable/absorbable materials and medical devices.

Science.gov (United States)

Liu, Chenghu; Luo, Hongyu; Wan, Min; Hou, Li; Wang, Xin; Shi, Yanping

2018-01-01

During the last two decades, biodegradable/absorbable materials which have many benefits over conventional implants are being sought in clinical practices. However, to date, it still remains obscure for us to perform full physic-chemical characterization and biological risk assessment for these materials and related devices due to their complex design and coherent processing. In this review, based on the art of knowledge for biodegradable/absorbable materials and biological risk assessment, we demonstrated some promising strategies to establish and improve the current biological evaluation systems for these biodegradable/absorbable materials and related medical devices.

Neutron activation analysis of biological material

International Nuclear Information System (INIS)

Kucera, J.; Simkova, M.; Obrusnik, I.

1985-01-01

The possibilities are briefly summed up of usino. NAA (neutron activation analysis) for determining element traces in foodstuffs and their intake by organisms, for monitoring changes in the content of important trace elements in tissues and body fluids owing to environmental pollution, for verifying the results of other analytical techniques and for certifying the content of element traces in reference materials. Examples are given of the use of NAA, and the results are summed up of the determination of Cd, Mn and Zn in biological reference materials NBS SRM-1577, Bovine Liver, Bowen's Kale, IAEA Milk Powder A-11 and IAEA Animal Muscle H-4. (E.S.)

Management, treatment and final disposal of solid hazardous hospital wastes

International Nuclear Information System (INIS)

Sebiani Serrano, T.

2000-01-01

Medical Waste is characterized by its high risk to human health and the environment. The main risk is biological, due to the large amount of biologically contaminated materials present in such waste. However, this does not mean that the chemical and radioactive wastes are less harmful just because they represent a smaller part of the total waste. Hazardous wastes from hospitals can be divided in 3 main categories: Solid Hazardous Hospital Wastes (S.H.H.W.), Liquid Hazardous Hospital Wastes (L.H.H.W.) and Gaseous Hazardous Hospital Wastes (G.H.H.W.) Most gaseous and liquid hazardous wastes are discharged to the environment without treatment. Since this inappropriate disposal practice, however, is not visible to society, there is no societal reaction to such problem. On the contrary, hazardous solid wastes (S.H.H.W.) are visible to society and create worries in the population. As a result, social and political pressures arise, asking for solutions to the disposal problems of such wastes. In response to such pressures and legislation approved by Costa Rica on waste handling and disposal, the Caja Costarricense de Seguro Social developed a plan for the handling, treatment, and disposal of hazardous solid wastes at the hospitals and clinics of its system. The objective of the program is to reduce the risk to society of such wastes. In this thesis a cost-effectiveness analysis was conducted to determine the minimum cost at which it is possible to reach a maximum level of reduction in hazardous wastes, transferring to the environment the least possible volume of solid hazardous wastes, and therefore, reducing risk to a minimum. It was found that at the National Children's Hospital the internal handling of hazard solid wastes is conducted with a high level of effectiveness. However, once out of the hospital area, the handling is not effective, because hazardous and common wastes are all mixed together creating a larger amount of S.H.H.W. and reducing the final efficiency

OECD Policy Recommendations on Security for Biological Materials

International Nuclear Information System (INIS)

Radisch, J.

2007-01-01

Biomedical innovations derived from research on pathogenic micro-organisms promise astounding health and economic benefits. Some such biological resources employed in the RandD for diagnostic kits, vaccines and therapeutics, however, possess capacity for dual-use; they may be misused to develop biological weapons. Research facilities entrusted with possession of such dual-use materials have a responsibility to comply with biosecurity measures that are designed to prevent loss or theft and thereby reduce the probability of a bioterrorist attack. The OECD has provided a forum for its Member countries to engage in a dialogue of international co-operation with a view to produce policies that achieve a research environment fortified by biosecurity measures and capable of producing health innovations. In 2007, the OECD developed a risk assessment framework and risk management principles for Biological Resource Centres. Ongoing policy work at the OECD will look to design biosecurity guidelines appropriate to a broader range of facilities in possession of dual-use materials, such as university and industrial laboratories.(author)

Control of biological hazards in cold smoked salmon production

DEFF Research Database (Denmark)

Huss, Hans Henrik; Embarek, Peter Karim Ben; Jeppesen, V.F.

1995-01-01

An outline of the common processing technology for cold smoked salmon in Denmark is presented. The safety hazards related to pathogenic bacteria, parasites and biogenic amines are discussed with special emphasis on hazards related to Clostridium botulinum and Listeria monocytogenes. Critical...... control points are identified for all hazards except growth of L. monocytogenes. For this reason a limitation of shelf life to three weeks at +5 degrees C far cold smoked vacuum-packed salmon having greater than or equal to 3% water phase salt is recommended...

40 CFR 260.43 - Legitimate recycling of hazardous secondary materials regulated under § 260.34, § 261.2(a)(2)(ii...

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Legitimate recycling of hazardous... (CONTINUED) HAZARDOUS WASTE MANAGEMENT SYSTEM: GENERAL Rulemaking Petitions § 260.43 Legitimate recycling of... demonstrate that the recycling is legitimate. Hazardous secondary material that is not legitimately recycled...

Two Chaotic Patterns of Dynamic Risk Definition for Solving Hazardous Materials Routing Problem

Directory of Open Access Journals (Sweden)

Abbas Mahmoudabadi

2015-01-01

Full Text Available In the case of determining routes for hazardous material transportation, risk is considered as a main attribute. Transport risk, which is usually combined with other attributes such as cost or travel time, plays a significant role in determining paths for hazardous materials transportation. Since, risk is chaotically affected by road incidents, decision makers are dealing with selecting a method for defining chaotic risk factors in hazmat transportation. In this paper, transport risk has been defined as a chaotic variable using two different methods of generating chaotic patterns. In an experimental road network, which consists of eighty-nine nodes and one hundred and one two-way links, two different methods of generating chaotic variables have been used for applying the proposed procedure. In addition, results for different amounts of risk and cost have also been analyzed in case study. Results revealed that different cost and risk priorities change the frequencies of selected paths determined for hazmat transportation, but the route convergence of the route to chaos method is better than that of the logistic map equation.

Biological and environmental reference materials in CENAM.

Science.gov (United States)

Arvizu-Torres, R; Perez-Castorena, A; Salas-Tellez, J A; Mitani-Nakanishi, Y

2001-06-01

Since 1994, when the NIST/NOAA Quality Assurance Program in Chemical Measurements was discussed in Queretaro, CENAM, the National Measurement Institute (NMI) of Mexico, has become involved in the development of reference materials. In the field of biological and environmental reference materials, in particular, the NORAMET collaboration program with NIST and NRC, and the North-American Environmental Cooperation signed among three free-trade treaty organizations, have greatly helped the development of the materials metrology program in the newly established CENAM. This paper describes some particularly significant efforts of CENAM in the development of biological and environmental reference materials, on the basis of inter-comparison studies organized with local and governmental environmental agencies of Mexico. In the field of water pollution CENAM has developed a practical proficiency testing (PT) scheme for field laboratories, as a part of registration by local government in the metropolitan area, according to the Mexican Ecological Regulation. The results from these eight PTs in the last 5 years have demonstrated that this scheme has helped ensure the reliability of analytical capability of more than 50 field laboratories in three states, Mexico, D.F., and the States of Mexico and Queretaro. Similar experience has been obtained for more than 70 service units of stack emission measurements in the three states in 1998 and 1999, as a result of the design of a PT scheme for reference gas mixtures. This PT scheme has been accomplished successfully by 30 analytical laboratories who provide monitoring services and perform research on toxic substances (Hg, methylmercury, PCB, etc.) in Mexico. To support these activities, reference samples have been produced through the NIST SRMs, and efforts have been made to increase CENAM's capability in the preparation of primary reference materials in spectrometric solutions and gas mixtures. Collaboration among NMIs has also

Hazardous materials safety and security technology field operational test. Volume II, evaluation final report synthesis

Science.gov (United States)

2004-11-11

The catastrophic events of September 11, 2001 and the ongoing war on terrorism have heightened the level of concern from Federal government officials and the transportation industry regarding the secure transport of hazardous materials (HAZMAT). Secu...

Mechanical properties of nanostructure of biological materials

Science.gov (United States)

Ji, Baohua; Gao, Huajian

2004-09-01

Natural biological materials such as bone, teeth and nacre are nanocomposites of protein and mineral with superior strength. It is quite a marvel that nature produces hard and tough materials out of protein as soft as human skin and mineral as brittle as classroom chalk. What are the secrets of nature? Can we learn from this to produce bio-inspired materials in the laboratory? These questions have motivated us to investigate the mechanics of protein-mineral nanocomposite structure. Large aspect ratios and a staggered alignment of mineral platelets are found to be the key factors contributing to the large stiffness of biomaterials. A tension-shear chain (TSC) model of biological nanostructure reveals that the strength of biomaterials hinges upon optimizing the tensile strength of the mineral crystals. As the size of the mineral crystals is reduced to nanoscale, they become insensitive to flaws with strength approaching the theoretical strength of atomic bonds. The optimized tensile strength of mineral crystals thus allows a large amount of fracture energy to be dissipated in protein via shear deformation and consequently enhances the fracture toughness of biocomposites. We derive viscoelastic properties of the protein-mineral nanostructure and show that the toughness of biocomposite can be further enhanced by the viscoelastic properties of protein.

Certification of biological reference materials by instrumental neutron activation analysis

International Nuclear Information System (INIS)

Lanjewar, Mamata R.; Lanjewar, R.B.

2014-01-01

A multielemental instrumental neutron activation analysis (INAA) method by short and long irradiation has been employed for the determination of 21 minor and trace elements in two standard Reference Materials P-RBF and P-WBF from Institute of Radioecology and Applied Nuclear Techniques ,Czechoslovakia. Also some biological standards such as Bowen's kale, cabbage leaves (Poland) including wheat and rice flour samples of local origin were analysed. It is suggested that INAA is an ideal method for the certification of Reference Materials of Biological Matrices. (author)

Generalized railway tank car safety design optimization for hazardous materials transport: Addressing the trade-off between transportation efficiency and safety

International Nuclear Information System (INIS)

Saat, Mohd Rapik; Barkan, Christopher P.L.

2011-01-01

North America railways offer safe and generally the most economical means of long distance transport of hazardous materials. Nevertheless, in the event of a train accident releases of these materials can pose substantial risk to human health, property or the environment. The majority of railway shipments of hazardous materials are in tank cars. Improving the safety design of these cars to make them more robust in accidents generally increases their weight thereby reducing their capacity and consequent transportation efficiency. This paper presents a generalized tank car safety design optimization model that addresses this tradeoff. The optimization model enables evaluation of each element of tank car safety design, independently and in combination with one another. We present the optimization model by identifying a set of Pareto-optimal solutions for a baseline tank car design in a bicriteria decision problem. This model provides a quantitative framework for a rational decision-making process involving tank car safety design enhancements to reduce the risk of transporting hazardous materials.

An overview of safety assessment, regulation, and control of hazardous material use at NREL

Science.gov (United States)

Nelson, B. P.; Crandall, R. S.; Moskowitz, P. D.; Fthenakis, V. M.

1992-12-01

This paper summarizes the methodology we use to ensure the safe use of hazardous materials at the National Renewable Energy Laboratory (NREL). First, we analyze the processes and the materials used in those processes to identify the hazards presented. Then we study federal, state, and local regulations and apply the relevant requirements to our operations. When necessary, we generate internal safety documents to consolidate this information. We design research operations and support systems to conform to these requirements. Before we construct the systems, we perform a semiquantitative risk analysis on likely accident scenarios. All scenarios presenting an unacceptable risk require system or procedural modifications to reduce the risk. Following these modifications, we repeat the risk analysis to ensure that the respective accident scenarios present an acceptable risk. Once all risks are acceptable, we conduct an operational readiness review (ORR). A management-appointed panel performs the ORR ensuring compliance with all relevant requirements. After successful completion of the ORR, operations can begin.

An overview of safety assessment, regulation, and control of hazardous material use at NREL

International Nuclear Information System (INIS)

Nelson, B.P.; Crandall, R.S.; Moskowitz, P.D.; Fthenakis, V.M.

1992-01-01

This paper summarizes the methodology we use to ensure the safe use of hazardous materials at the National Renewable Energy Laboratory (NREL). First, we analyze the processes and the materials used in those processes to identify the hazards presented. Then we study federal, state, and local regulations and apply the relevant requirements to our operations. When necessary, we generate internal safety documents to consolidate this information. We design research operations and support systems to conform to these requirements. Before we construct the systems, we perform a semiquantitative risk analysis on likely accident scenarios. All scenarios presenting in unacceptable risk require system or procedural modifications to reduce the risk. Following these modifications, we repeat the risk analysis to ensure that the respective accident scenarios present acceptable risk. Once all risks are acceptable, we conduct an operational readiness review (ORR). A management appointed panel performs the ORR ensuring compliance with all relevant requirements. After successful completion of the ORR, operations can begin

An overview of safety assessment, regulation, and control of hazardous material use at NREL

International Nuclear Information System (INIS)

Nelson, B.P.; Crandall, R.S.; Moskowitz, P.D.; Fthenakis, V.M.

1992-01-01

This paper summarizes the methodology we use to ensure the safe use of hazardous materials at the National Renewable Energy Laboratory (NREL). First, we analyze the processes and the materials used in those processes to identify the hazards presented. Then we study federal, state, and local regulations and apply the relevant requirements to our operations. When necessary, we generate internal safety documents to consolidate this information. We design research operations and support systems to conform to these requirements. Before we construct the systems, we perform a semiquantitative risk analysis on likely accident scenarios. All scenarios presenting an unacceptable risk require system or procedural modifications to reduce the risk. Following these modifications, we repeat the risk analysis to ensure that the respective accident scenarios present an acceptable risk. Once all risks are acceptable, we conduct an operational readiness review (ORR). A management-appointed panel performs the ORR ensuring compliance with all relevant requirements. After successful completion of the ORR, operations can begin

Assessment of natural radioactivity and associated radiation hazards in some Cameroonian building materials

Energy Technology Data Exchange (ETDEWEB)

Ngachin, M. [Center for Atomic, Molecular Physics and Quantum Optics, University of Douala, P.O. Box 8580, Douala (Cameroon) and Abdus Salam International Center for Theoretical Physics, Strada Costiera 11, 34014 Trieste (Italy)]. E-mail: mngachin@yahoo.com; Garavaglia, M. [Regional Agency for Environmental Protection (ARPA), 91 via Tavagnacco, 33100 Udine (Italy); Giovani, C. [Regional Agency for Environmental Protection (ARPA), 91 via Tavagnacco, 33100 Udine (Italy); Kwato Njock, M.G. [Center for Atomic, Molecular Physics and Quantum Optics, University of Douala, P.O. Box 8580, Douala (Cameroon); Nourreddine, A. [Institut Pluridisciplinaire Hubert Curien, UMR7500 CNRS-IN2P3 et Universite Louis Pasteur, 23 Rue du Loess, BP 28, F-67037, Strasbourg Cedex 2 (France)

2007-01-15

The concentration of {sup 238}U, {sup 232}Th and {sup 40}K in 13 building materials obtained from factories and collected in field in Cameroon were investigated by {gamma}-ray spectrometry. The activity ranged from 1.76 to 49.84Bqkg{sup -1}, 0.32 to 147Bqkg{sup -1} and 18 to 1226Bqkg{sup -1} for {sup 238}U, {sup 232}Th and {sup 40}K, respectively. The highest {sup 238}U activity was found in compressed red soil brick type I (49.6+/-0.3Bqkg{sup -1}) produced by a local manufacturer while the highest {sup 232}Th (139+/-13Bqkg{sup -1}) and {sup 40}K (1162+/-108Bqkg{sup -1}) activities were found in gravel collected from an exploitation site in Logbadjeck. The activities are compared with available data from other investigations and with the world average value for soils. The radium equivalent activity Ra{sub eq}, the external hazard index H{sub ex}, the indoor absorbed dose rate D-bar in air and the annual effective dose equivalent E-bar were evaluated to assess the radiation hazard for people living in dwellings made of the materials studied. All building materials have shown Ra{sub eq} (range from 10 to 313Bqkg{sup -1}) lower than the limit of 370Bqkg{sup -1} set in the Organization for Economic Cooperation and Development [OECD, 1979. Exposure to radiation from the natural radioactivity in building materials. OECD, Paris] report which is equivalent to a {gamma}-dose of 1.5mSvyr{sup -1}. Except for the gravel from Logbadjeck, all the materials examined are acceptable for use as building materials as defined by the OECD criterion.

Robust routing for hazardous materials transportation with conditional value-at-risk on time-dependent networks.

Science.gov (United States)

2012-11-01

New methods are proposed for mitigating risk in hazardous materials (hazmat) transportation, based on Conditional : Value-at-Risk (CVaR) measure, on time-dependent vehicular networks. While the CVaR risk measure has been : popularly used in financial...

Development of tools for integrated monitoring and assessment of hazardous substances and their biological effects in the Baltic Sea.

Science.gov (United States)

Lehtonen, Kari K; Sundelin, Brita; Lang, Thomas; Strand, Jakob

2014-02-01

The need to develop biological effects monitoring to facilitate a reliable assessment of hazardous substances has been emphasized in the Baltic Sea Action Plan of the Helsinki Commission. An integrated chemical-biological approach is vitally important for the understanding and proper assessment of anthropogenic pressures and their effects on the Baltic Sea. Such an approach is also necessary for prudent management aiming at safeguarding the sustainable use of ecosystem goods and Services. The BEAST project (Biological Effects of Anthropogenic Chemical Stress: Tools for the Assessment of Ecosystem Health) set out to address this topic within the BONUS Programme. BEAST generated a large amount of quality-assured data on several biological effects parameters (biomarkers) in various marine species in different sub-regions of the Baltic Sea. New indicators (biological response measurement methods) and management tools (integrated indices) with regard to the integrated monitoring approach were suggested.

Solid freeform fabrication of biological materials

Science.gov (United States)

Wang, Jiwen

This thesis investigates solid freeform fabrication of biological materials for dental restoration and orthopedic implant applications. The basic approach in this study for solid freeform fabrication of biological materials is micro-extrusion of single or multiple slurries for 3D components and inkjet color printing of multiple suspensions for functionally graded materials (FGMs). Common issues associated with micro-extrusion and inkjet color printing are investigated. These common issues include (i) formulation of stable slurries with a pseudoplastic property, (ii) cross-sectional geometry of the extrudate as a function of the extrusion parameters, (iii) fabrication path optimization for extrusion process, (iv) extrusion optimization for multi-layer components, (v) composition control in functionally graded materials, and (vi) sintering optimization to convert the freeform fabricated powder compact to a dense body for biological applications. The present study clearly shows that the rheological and extrusion behavior of dental porcelain slurries depend strongly on the pH value of the slurry and extrusion conditions. A slurry with pseudoplastic properties is a basic requirement for obtaining extruded lines with rectangular cross-sections. The cross-sectional geometry of the extrudate is also strongly affected by extrusion parameters including the extrusion nozzle height, nozzle moving speed, extrusion rate, and critical nozzle height. Proper combinations of these extrusion parameters are necessary in order to obtain single line extrudates with near rectangular cross-sections and 3D objects with dimensional accuracy, uniform wall thickness, good wall uprightness, and no wall slumping. Based on these understandings, single-wall, multi-wall, and solid teeth have been fabricated via micro-extrusion of the dental slurry directly from a CAD digital model in 30 min. Inkjet color printing using stable Al2O3 and ZrO 2 aqueous suspensions has been developed to fabricate

Fate and transport processes controlling the migration of hazardous and radioactive materials from the Area 5 Radioactive Waste Management Site (RWMS)

International Nuclear Information System (INIS)

Estrella, R.

1994-10-01

Desert vadose zones have been considered as suitable environments for the safe and long-term isolation of hazardous wastes. Low precipitation, high evapotranspiration and thick unsaturated alluvial deposits commonly found in deserts make them attractive as waste disposal sites. The fate and transport of any contaminant in the subsurface is ultimately determined by the operating retention and transformation processes in the system and the end result of the interactions among them. Retention (sorption) and transformation are the two major processes that affect the amount of a contaminant present and available for transport. Retention processes do not affect the total amount of a contaminant in the soil system, but rather decrease or eliminate the amount available for transport at a given point in time. Sorption reactions retard the contaminant migration. Permanent binding of solute by the sorbent is also possible. These processes and their interactions are controlled by the nature of the hazardous waste, the properties of the porous media and the geochemical and environmental conditions (temperature, moisture and vegetation). The present study summarizes the available data and investigates the fate and transport processes that govern the migration of contaminants from the Radioactive Waste Management Site (RWMS) in Area 5 of the Nevada Test Site (NTS). While the site is currently used only for low-level radioactive waste disposal, past practices have included burial of material now considered hazardous. Fundamentals of chemical and biological transformation processes are discussed subsequently, followed by a discussion of relevant results

Fate and transport processes controlling the migration of hazardous and radioactive materials from the Area 5 Radioactive Waste Management Site (RWMS)

Energy Technology Data Exchange (ETDEWEB)

Estrella, R.

1994-10-01

Desert vadose zones have been considered as suitable environments for the safe and long-term isolation of hazardous wastes. Low precipitation, high evapotranspiration and thick unsaturated alluvial deposits commonly found in deserts make them attractive as waste disposal sites. The fate and transport of any contaminant in the subsurface is ultimately determined by the operating retention and transformation processes in the system and the end result of the interactions among them. Retention (sorption) and transformation are the two major processes that affect the amount of a contaminant present and available for transport. Retention processes do not affect the total amount of a contaminant in the soil system, but rather decrease or eliminate the amount available for transport at a given point in time. Sorption reactions retard the contaminant migration. Permanent binding of solute by the sorbent is also possible. These processes and their interactions are controlled by the nature of the hazardous waste, the properties of the porous media and the geochemical and environmental conditions (temperature, moisture and vegetation). The present study summarizes the available data and investigates the fate and transport processes that govern the migration of contaminants from the Radioactive Waste Management Site (RWMS) in Area 5 of the Nevada Test Site (NTS). While the site is currently used only for low-level radioactive waste disposal, past practices have included burial of material now considered hazardous. Fundamentals of chemical and biological transformation processes are discussed subsequently, followed by a discussion of relevant results.

Guidelines for applying criteria to designate routes for transporting hazardous materials. Final report

International Nuclear Information System (INIS)

1989-07-01

These guidelines were prepared to assist State and local officials in the analysis of alternate routes to be used by highway vehicles transportating hazardous materials. A methodology for assessing comparative risks of routing alternatives is discussed and demonstrated through a hypothetical example. Mathematical models are provided for situations in which measured local data may not be easily obtained or adequate

Comparative study on biological effects of gamma-radiation and volatile organic compound with the plant bioassay

International Nuclear Information System (INIS)

Shin, H. S.; Lee, J. H.; Kim, J. G.

2003-01-01

This research examined the presence of hazardous materials in chemical workplace field by means of an integrated biological monitoring. The pollen mother cells (PMC) of Tradescantia are very sensitive to chemical toxicants or ionizing radiation, and thus can be used as a biological end- point as sessing their effect. A parallel series of experiment using five increasing doses of gamma- ray at 10, 20, 30, 40 and 50 cGy was conducted. The MCN frequencies showed a good dose-response relationship in the range of radiation applied and yielded a correlation coefficient of 0.95. On the other hand, the MCN frequency resulted in a good response to exposure time in the workplace field. In case of in situ monitoring with the Tradescantia micronucleus assay, the frequencies were 6.2± 0.5, 8.2±1.0, and 15.7± 0.8 MCN/ 100 tetrads for 2, 6, and 9 hours exposure, respectively. Inhalation of the workplace air by workers may result in chronic damage to their health as proven by micronucleus formations in Tradescantia pollen mother cells. The combination of chemical/ biological monitoring is very effective to evaluate hazardous materials in workplace field and can be alternatively used for screening hazardous materials

Incidents with hazardous radiation sources

International Nuclear Information System (INIS)

Schoenhacker, Stefan

2016-01-01

Incidents with hazardous radiation sources can occur in any country, even those without nuclear facilities. Preparedness for such incidents is supposed to fulfill globally agreed minimum standards. Incidents are categorized in incidents with licensed handling of radiation sources as for material testing, transport accidents of hazardous radiation sources, incidents with radionuclide batteries, incidents with satellites containing radioactive inventory, incidents wit not licensed handling of illegally acquired hazardous radiation sources. The emergency planning in Austria includes a differentiation according to the consequences: incidents with release of radioactive materials resulting in restricted contamination, incidents with release of radioactive materials resulting in local contamination, and incidents with the hazard of e@nhanced exposure due to the radiation source.

MAK- and BAT values list 2000. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

International Nuclear Information System (INIS)

2000-01-01

The definitions and use of MAK and BAT values for hazardous materials are presented, and tables are presented for various hazardous materials, e.g. carcinogenic and allergogenic materials, aerosols and organic substances such as peroxides, benzenes, turpentine oil, and cooling lubricants. (SR) [de

Biological and environmental hazards

International Nuclear Information System (INIS)

Budinger, T.F.

1987-01-01

This chapter examines the biophysics of static and oscillating magnetic fields interacting with human tissue. The known or predicted efforts concern implants such as surgical clips and pacemakers, and there are potential heating effects if the radiofrequency (RF) exposure is excessive. Guidelines have been presented by various health advisory organizations in the United Kingdom, the United States of America, and Germany. Present instrumentation specifications and uses generally fall within these guidelines, which are intended to be advisories and not limits, at least in the United States. But interest in the use of fields beyond 2 T and the use of rapidly switched gradients and RF power deposition beyond the limits of the present guidelines necessitate continuing biophysical studies and investigations of adverse effects. The potential health hazards are presented under three categories: static field, time-varying fields of the gradient system, and time-varying fields of the magnetic RF system

Bioprocessing of low-level radioactive and mixed hazard wastes

International Nuclear Information System (INIS)

Stoner, D.L.

1990-01-01

Biologically-based treatment technologies are currently being developed at the Idaho National Engineering Laboratory (INEL) to aid in volume reduction and/or reclassification of low-level radioactive and mixed hazardous wastes prior to processing for disposal. The approaches taken to treat low-level radioactive and mixed wastes will reflect the physical (e.g., liquid, solid, slurry) and chemical (inorganic and/or organic) nature of the waste material being processed. Bioprocessing utilizes the diverse metabolic and biochemical characteristics of microorganisms. The application of bioadsorption and bioflocculation to reduce the volume of low-level radioactive waste are strategies comparable to the use of ion-exchange resins and coagulants that are currently used in waste reduction processes. Mixed hazardous waste would require organic as well as radionuclide treatment processes. Biodegradation of organic wastes or bioemulsification could be used in conjunction with radioisotope bioadsorption methods to treat mixed hazardous radioactive wastes. The degradation of the organic constituents of mixed wastes can be considered an alternative to incineration, while the use of bioemulsification may simply be used as a means to separate inorganic and organics to enable reclassification of wastes. The proposed technology base for the biological treatment of low-level radioactive and mixed hazardous waste has been established. Biodegradation of a variety of organic compounds that are typically found in mixed hazardous wastes has been demonstrated, degradative pathways determined and the nutritional requirements of the microorganisms are understood. Accumulation, adsorption and concentration of heavy and transition metal species and transuranics by microorganisms is widely recognized. Work at the INEL focuses on the application of demonstrated microbial transformations to process development

Assessment of radiological hazards of naturally occurring radioactive materials in cement industry

International Nuclear Information System (INIS)

Aslam, M.; Gul, R.; Ara, T.; Hussain, M.

2012-01-01

A study on the radiological hazard in Portland cement due to the presence of naturally occurring radioactive materials is being carried out. The Portland cement manufactured in the Islamabad/Rawalpindi region of Pakistan, intermediate products (clinker) and the various raw materials which compose the product have been analysed for 226 Ra, 232 Th and 40 K using a gamma spectrometry system with a N-type high-purity germanium detector of 80 % relative efficiency. From the measured gamma ray spectra, specific activities were determined. The mean values of the total specific activity of 226 Ra, 232 Th and 40 K are 34.2±11.9, 29.1±3.6 and 295.1±66.9 Bq kg -1 , respectively in Portland cement, 28.4±8.7, 11.3±1.7 and 63.1±17.3 Bq kg -1 , respectively in lime stone, 8.2±1.9, 16.2±3.9 and 187.7±53.2 Bq kg -1 , respectively in gypsum, 34.7±13.1, 41.2±6.7 and 187.6±17.2 Bq kg -1 , respectively in clay, 41.1±11.8, 39.3±6.9 and 195.1±29.2 Bq kg -1 , respectively in laterite and 51.1±18.2, 23.2±1.2 and 258.4±15.3 Bq kg -1 , respectively in clinker. The radium equivalent activities (Ra eq ), external hazard index (H ex ), internal hazard index (H in ), absorbed dose rate in air (D) and annual effective dose rate (E eff ) were also determined. The measured activity concentrations for these radio nuclides and radiological indices were compared with the reported national and international data. All these measured values are comparable with the worldwide data reported in UNSCEAR publications. (authors)

Radiant business. Hazards of international, illicit trafficking with nuclear materials

International Nuclear Information System (INIS)

Attali, J.

1996-03-01

Since the Cold War has been terminated, public media increasingly come out with reports about cases of illicit trafficking with nuclear technology and nuclear materials. So far, the potential hazard has not been exploding into the big disaster, but imagine what may happen if uranium or plutonium falls into the hands of terrorists, fanatics, or Mafia-type organisations ? The author has been investigating into this problem on behalf of the Secretary General of the UN. He has been travelling all around the world in pursuit of information and indications, and now presents us with the essential results of his mission, compiled in this explosive report. (orig./HP) [de

Biological and environmental reference materials for trace elements, nuclides and organic microcontaminants

International Nuclear Information System (INIS)

Cortes Toro, E.; Parr, R.M.; Clements, S.A.

1990-01-01

This report has been produced from a database on analytical reference materials of biological and environmental origin, which is maintained at the International Atomic Energy Agency. It is an updated version of an earlier report, published in 1985, which focussed mainly on reference materials for trace elements. In the present version of the report, reference materials for trace elements still constitute the major part of the data; however, information is also now included on a number of other selected analytes of relevance to IAEA programmes, i.e. radionuclides, stable isotopes and organic microcontaminants. The database presently contains 2,694 analyte values for 117 analytes in 116 biological and 77 environmental (non-biological) reference materials produced by 20 different suppliers. Additional information on the cost of the material, the unit size supplied, (weight or volume), and the minimum weight of material recommended for analysis is also provided (if available to the authors). It is expected that this report will help analysts to select the reference material that matches as closely as possible, with respect to matrix type and concentrations of the analytes of interest, the ''real'' samples that are to be analysed. Refs, 12 tabs

Flexible Organic Electronics in Biology: Materials and Devices.

Science.gov (United States)

Liao, Caizhi; Zhang, Meng; Yao, Mei Yu; Hua, Tao; Li, Li; Yan, Feng

2015-12-09

At the convergence of organic electronics and biology, organic bioelectronics attracts great scientific interest. The potential applications of organic semiconductors to reversibly transmit biological signals or stimulate biological tissues inspires many research groups to explore the use of organic electronics in biological systems. Considering the surfaces of movable living tissues being arbitrarily curved at physiological environments, the flexibility of organic bioelectronic devices is of paramount importance in enabling stable and reliable performances by improving the contact and interaction of the devices with biological systems. Significant advances in flexible organic bio-electronics have been achieved in the areas of flexible organic thin film transistors (OTFTs), polymer electrodes, smart textiles, organic electrochemical ion pumps (OEIPs), ion bipolar junction transistors (IBJTs) and chemiresistors. This review will firstly discuss the materials used in flexible organic bioelectronics, which is followed by an overview on various types of flexible organic bioelectronic devices. The versatility of flexible organic bioelectronics promises a bright future for this emerging area. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effects of chemical and biological warfare remediation agents on the materials of museum objects

Science.gov (United States)

Solazzo, C.; Erhardt, D.; Marte, F.; von Endt, D.; Tumosa, C.

In the fall of 2001, anthrax-contaminated letters were sent to public figures in the United States. Chemical and radiation treatments were employed to decontaminate exposed buildings, objects, and materials. These treatments are effective, but potentially damaging to exposed objects and materials. The recommended surface chemical treatments include solutions, gels, and foams of oxidizing agents such as peroxides or chlorine bleaching agents. Such oxidizing agents are effective against a wide range of hazardous chemical and biological agents. Knowing how these reagents affect various substrates would help to anticipate and to minimize any potential damage. We are examining the effects on typical museum materials of reagents likely to be used, including hydrogen peroxide, sodium hypochlorite, and potassium peroxymonosulfate. Results so far show significant changes in a number of materials. Surface corrosion was observed on metals such as copper, silver, iron, and brass. Color changes occurred with at least one reagent in about one-fourth of the dyed fabric swatches tested, and about half of the inks. Samples of aged yellowed paper are bleached. Effects varied with both the substrate and the tested reagent. The observed changes were generally less drastic than might have been expected. Enough materials were affected, though, to preclude the use of these reagents on museum objects unless no less drastic alternative is available. It appears that many objects of lesser intrinsic value can be treated without severe loss of properties or usefulness. For example, most documents should remain legible if the appropriate reagent is used. This work will provide a basis for determining which treatment is most appropriate for a specific situation and what consequences are to be expected from other treatments.

Implications of the Differential Toxicological Effects of III-V Ionic and Particulate Materials for Hazard Assessment of Semiconductor Slurries.

Science.gov (United States)

Jiang, Wen; Lin, Sijie; Chang, Chong Hyun; Ji, Zhaoxia; Sun, Bingbing; Wang, Xiang; Li, Ruibin; Pon, Nanetta; Xia, Tian; Nel, André E

2015-12-22

Because of tunable band gaps, high carrier mobility, and low-energy consumption rates, III-V materials are attractive for use in semiconductor wafers. However, these wafers require chemical mechanical planarization (CMP) for polishing, which leads to the generation of large quantities of hazardous waste including particulate and ionic III-V debris. Although the toxic effects of micron-sized III-V materials have been studied in vivo, no comprehensive assessment has been undertaken to elucidate the hazardous effects of submicron particulates and released III-V ionic components. Since III-V materials may contribute disproportionately to the hazard of CMP slurries, we obtained GaP, InP, GaAs, and InAs as micron- (0.2-3 μm) and nanoscale (particles for comparative studies of their cytotoxic potential in macrophage (THP-1) and lung epithelial (BEAS-2B) cell lines. We found that nanosized III-V arsenides, including GaAs and InAs, could induce significantly more cytotoxicity over a 24-72 h observation period. In contrast, GaP and InP particulates of all sizes as well as ionic GaCl3 and InCl3 were substantially less hazardous. The principal mechanism of III-V arsenide nanoparticle toxicity is dissolution and shedding of toxic As(III) and, to a lesser extent, As(V) ions. GaAs dissolves in the cell culture medium as well as in acidifying intracellular compartments, while InAs dissolves (more slowly) inside cells. Chelation of released As by 2,3-dimercapto-1-propanesulfonic acid interfered in GaAs toxicity. Collectively, these results demonstrate that III-V arsenides, GaAs and InAs nanoparticles, contribute in a major way to the toxicity of III-V materials that could appear in slurries. This finding is of importance for considering how to deal with the hazard potential of CMP slurries.

Hazardous properties and environmental effects of materials used in solar heating and cooling (SHAC) technologies: interim handbook

Energy Technology Data Exchange (ETDEWEB)

Searcy, J.Q.

1978-12-01

General background informaion related to SHAC systems, how a particular material was chosen for this handbook, and codes and standards are given. Materials are categorized according to their functional use in SHAC systems as follows: (1) heat transfer fluids and fluid treatment chemicals, (2) insulation materials, (3) seals and sealant materials, (4) glazing materials, (5) collector materials, and (6) storage media. The informaion is presented under: general properties, chemical composition, thermal degradation products, and thermoxidative products of some commercial materials; toxic properties and other potential health effects; fire hazard properties; and environmental effects of and disposal methods for SHAC materials. (MHR)

Informing Workers of Chemical Hazards: The OSHA Hazard Communication Standard.

Science.gov (United States)

American Chemical Society, Washington, DC.

Practical information on how to implement a chemical-related safety program is outlined in this publication. Highlights of the federal Occupational Safety and Health Administrations (OSHA) Hazard Communication Standard are presented and explained. These include: (1) hazard communication requirements (consisting of warning labels, material safety…

Probabilistic Approach to Conditional Probability of Release of Hazardous Materials from Railroad Tank Cars during Accidents

Science.gov (United States)

2009-10-13

This paper describes a probabilistic approach to estimate the conditional probability of release of hazardous materials from railroad tank cars during train accidents. Monte Carlo methods are used in developing a probabilistic model to simulate head ...

Converting environmentally hazardous materials into clean energy using a novel nanostructured photoelectrochemical fuel cell

Energy Technology Data Exchange (ETDEWEB)

Gan, Yong X., E-mail: yong.gan@utoledo.edu [Department of Mechanical, Industrial and Manufacturing Engineering, College of Engineering, University of Toledo, Toledo, OH 43606 (United States); Gan, Bo J. [Ottawa Hills High School, 2532 Evergreen Road, Toledo, OH 43606 (United States); Clark, Evan; Su, Lusheng [Department of Mechanical, Industrial and Manufacturing Engineering, College of Engineering, University of Toledo, Toledo, OH 43606 (United States); Zhang, Lihua [Center for Functional Nanomaterials, Brookhaven National Laboratory, Upton, NY 11973 (United States)

2012-09-15

Highlights: ► A photoelectrochemical fuel cell has been made from TiO{sub 2} nanotubes. ► The fuel cell decomposes environmentally hazardous materials to produce electricity. ► Doping the anode with a transition metal oxide increases the visible light sensitivity. ► Loading the anode with a conducting polymer enhances the visible light absorption. -- Abstract: In this work, a novel photoelectrochemical fuel cell consisting of a titanium dioxide nanotube array photosensitive anode and a platinum cathode was made for decomposing environmentally hazardous materials to produce electricity and clean fuel. Titanium dioxide nanotubes (TiO{sub 2} NTs) were prepared via electrochemical oxidation of pure Ti in an ammonium fluoride and glycerol-containing solution. Scanning electron microscopy was used to analyze the morphology of the nanotubes. The average diameter, wall thickness and length of the as-prepared TiO{sub 2} NTs were determined. The photosensitive anode made from the highly ordered TiO{sub 2} NTs has good photo-catalytic property, as proven by the decomposition tests on urea, ammonia, sodium sulfide and automobile engine coolant under ultraviolet (UV) radiation. To improve the efficiency of the fuel cell, doping the TiO{sub 2} NTs with a transition metal oxide, NiO, was performed and the photosensitivity of the doped anode was tested under visible light irradiation. It is found that the NiO-doped anode is sensitive to visible light. Also found is that polyaniline-doped photosensitive anode can harvest photon energy in the visible light spectrum range much more efficiently than the NiO-doped one. It is concluded that the nanostructured photoelectrochemical fuel cell can generate electricity and clean fuel by decomposing hazardous materials under sunlight.

Biological effects of ionizing radiation - changing worker attitudes

International Nuclear Information System (INIS)

Johnson, N.; Schenley, C.

1989-01-01

Training Resources and Data Exchange (TRADE) Radiation Protection Training Special Interest Group has taken an innovative approach to providing DOE contractors with radiation worker training material information. Newly-hired radiation workers may be afraid to work near radiation and long-term radiation workers may become indifferent to the biological hazard of radiation. Commercially available training material is often presented at an inappropriate technical level or in an uninteresting style. These training problems have been addressed in the DOE system through development of a training videotape and supporting material package entitled Understanding Ionizing Radiation and its Biological Effects. The training package, developed and distributed by TRADE specifically to meet the needs of DOE contractor facilities, contains the videotape and accompanying paper supporting materials designed to assist the instructor. Learning objectives, presentation suggestion for the instructor, trainee worksheets, guided discussion questions, and trainee self-evaluation sheets are included in the training package. DOE contractors have agreed that incorporating this training module into radiation worker training programs enhances the quality of the training and increase worker understanding of the biological effects of ionizing radiation

Offsite transportation hazards assessment

International Nuclear Information System (INIS)

Burnside, M.E.

1997-01-01

This report documents the emergency preparedness Hazards Assessment for the offsite transportation of hazardous material from the Hanford Site. The assessment is required by the US Department of Energy (DOE) Order 151.1. Offsite transportation accidents are categorized using the DOE system to assist communication within the DOE and assure that appropriate assistance is provided to the people in charge at the scene. The assistance will initially include information about the load and the potential hazards. Local authorities will use the information to protect the public following a transportation accident. This Hazards Assessment will focus on the material being transported from the Hanford Site. Shipments coming to Hanford are the responsibility of the shipper and the carrier and, therefore, are not included in this Hazards Assessment, unless the DOE elects to be the shipper of record

75 FR 63 - Hazardous Materials: Revision to Requirements for the Transportation of Batteries and Battery...

Science.gov (United States)

2010-01-04

... contained in equipment, fuel cell systems must not charge batteries during transport; (3) For transportation... 2137-AE54 Hazardous Materials: Revision to Requirements for the Transportation of Batteries and Battery... batteries and battery-powered devices. This final rule corrects several errors in the January 14, 2009 final...

77 FR 17394 - Hazardous Materials: Approval and Communication Requirements for the Safe Transportation of Air...

Science.gov (United States)

2012-03-26

... seat-belt pretensioner devices to a capacity not greater than fifty (50) percent of the drum's total... transported; transportation operations conducted under a special permit; the potential for broad application... utilized by 31 grantees with no known safety problems. A review of the Hazardous Materials Incident Data...

How accelerated biological aging can affect solar reflective polymeric based building materials

Science.gov (United States)

Ferrari, C.; Santunione, G.; Libbra, A.; Muscio, A.; Sgarbi, E.

2017-11-01

Among the main issues concerning building materials, in particular outdoor ones, one can identify the colonization by microorganisms referred to as biological aggression. This can affect not only the aesthetical aspect but also the thermal performance of solar reflective materials. In order to improve the reliability of tests aimed to assess the resistance to biological aggression and contextually reduce the test duration, an accelerated test method has been developed. It is based on a lab reproducible setup where specific and controlled environmental and boundary conditions are imposed to accelerate as much as possible biological growth on building materials. Due to their widespread use, polymeric materials have been selected for the present analysis, in the aim of reaching an advanced bio-aged level in a relatively short time (8 weeks or less) and at the same time comparatively evaluate different materials under a given set of ageing conditions. Surface properties before, during and after ageing have been investigated by surface, microstructural and chemical analyses, as well as by examination of time progressive images to assess bacterial and algal growth rate.

Worker safety for occupations affected by the use, transportation and storage of radioactive and hazardous materials

International Nuclear Information System (INIS)

1994-07-01

A study group under the auspices of the National Conference of State Legislatures (NCSL) Labor Committee and the High-level Radioactive Waste/Hazardous Materials Transportation Task Force examined worker protection and safety programs for occupations affected by the use, transportation and storage of radioactive and hazardous materials. Concern about the risks posed to people who live along spent nuclear fuel transportation routes has led to demands for redundant inspections of the transported spent fuel. It would also be prudent to examine the radiological risk to the inspectors themselves before state of federal regulations are promulgated which require redundant inspections. Other workers may also come close to a spent fuel cask during normal operations. The dose rate to which these inspectors and handlers are exposed is higher than the dose rate to which any other group is exposed during incident-free truck transportation and higher than the dose rate to the drivers when they are in the truck cab. This report consists of miscellaneous papers covering topics related to determining radiation doses to workers involved in the transport of radioactive materials

Report: EPA Provided Quality and Timely Information on Hurricane Katrina Hazardous Material Releases and Debris Management

Science.gov (United States)

Report #2006-P-00023, May 2, 2006. After Hurricane Katrina, EPA was the agency with lead responsibility to prevent, minimize, or mitigate threats to public health and the environment caused by hazardous materials and oil spills in inland zones.

Transport of biologically active material in laser cutting.

Science.gov (United States)

Frenz, M; Mathezloic, F; Stoffel, M H; Zweig, A D; Romano, V; Weber, H P

1988-01-01

The transport of biologically active material during laser cutting with CO2 and Er lasers is demonstrated. This transport mechanism removes particles from the surface of gelatin, agar, and liver samples into the depth of the laser-formed craters. The transport phenomenon is explained by a contraction and condensation of enclosed hot water vapor. We show by cultivating transported bacteria in agar that biological particles can survive the shock of the transport. Determination of the numbers of active cells evidences a more pronounced activity of the cultivated bacteria after impact with an Er laser than with a CO2 laser.

Development of Standards for NanoSIMS Analyses of Biological Materials

Energy Technology Data Exchange (ETDEWEB)

Davission, M L; Weber, P K; Pett-Ridge, J; Singer, S

2008-07-31

NanoSIMS is a powerful analytical technique for investigating element distributions at the nanometer scale, but quantifying elemental abundances requires appropriate standards, which are not readily available for biological materials. Standards for trace element analyses have been extensively developed for secondary ion mass spectrometry (SIMS) in the semiconductor industry and in the geological sciences. The three primary approaches for generating standards for SIMS are: (1) ion implantation (2) using previously characterized natural materials, and (3) preparing synthetic substances. Ion implantation is a reliable method for generating trace element standards, but it is expensive, which limits investigation of the analytical issues discussed above. It also requires low background levels of the elements of interest. Finding or making standard materials has the potential to provide more flexibility than ion implantation, but realizing homogeneity at the nano-scale is in itself a significant challenge. In this study, we experiment with all three approaches, but with an emphasis toward synthetic organic polymers in order to reduce costs, increase flexibility, and achieve a wide dynamic concentration range. This emphasis serves to meet the major challenge for biological samples of identifying matrix matched, homogeneous material. Biological samples themselves are typically heterogeneous at the scale of microns to 100s of microns, and therefore they are poor SIMS standards. Therefore, we focused on identifying 'biological-like' materials--either natural or synthetic--that can be used for standards. The primary criterion is that the material be as compositionally similar to biological samples as possible (primarily C, H, O, and N). For natural material we adsorbed organic colloids consisting of peptidoglycan (i.e., amino sugars), activated charcoal, and humic acids. Experiments conducted with Si on peptidoglycan showed low affinity as SiO{sub 2}, yet its

Recovering energy and materials from hazardous waste

Energy Technology Data Exchange (ETDEWEB)

Anon.

2003-12-01

The tannery industry faces growing environmental concerns because of the high hazardous metal content of its process waste. The formation, during the tanning process, of the highly toxic hexavalent chromium precludes the use of conventional thermal incineration processes. Borge Tannery in Norway, which processes 600 cattle hides per day, has solved the problem by using new PyroArc technology. The PyroArc waste processing plant can treat all of the tannery's production wastes, transforming them into useful products such as fuel gas and re-usable metal. The fuel gas consists mainly of carbon monoxide, hydrogen and nitrogen, and has a calorific value of about 4 MJ/Nm{sub 3}. About 65-70% of the energy content of the source material (waste or biomass) is recovered in the gas, and this is used to produce steam and/or electricity in a gas engine with a capacity of 580 kW. A further 20-25% of the initial energy content is recovered as heat or low-pressure steam. The plant is designed to be self-sufficient in energy (1.5 MW) and to meet the tannery's maximum requirements for hot water and steam. (UK)

Hazards assessment for the Waste Experimental Reduction Facility

International Nuclear Information System (INIS)

Calley, M.B.; Jones, J.L. Jr.

1994-01-01

This report documents the hazards assessment for the Waste Experimental Reduction Facility (WERF) located at the Idaho National Engineering Laboratory, which is operated by EG ampersand G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility's operational emergency management program. This hazards assessment describes the WERF, the area surrounding WERF, associated buildings and structures at WERF, and the processes performed at WERF. All radiological and nonradiological hazardous materials stored, used, or produced at WERF were identified and screened. Even though the screening process indicated that the hazardous materials could be screened from further analysis because the inventory of radiological and nonradiological hazardous materials were below the screening thresholds specified by DOE and DOE-ID guidance for DOE Order 5500.3A, the nonradiological hazardous materials were analyzed further because it was felt that the nonradiological hazardous material screening thresholds were too high

Hazards assessment for the Waste Experimental Reduction Facility

Energy Technology Data Exchange (ETDEWEB)

Calley, M.B.; Jones, J.L. Jr.

1994-09-19

This report documents the hazards assessment for the Waste Experimental Reduction Facility (WERF) located at the Idaho National Engineering Laboratory, which is operated by EG&G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes hazards that are significant enough to warrant consideration in a facility`s operational emergency management program. This hazards assessment describes the WERF, the area surrounding WERF, associated buildings and structures at WERF, and the processes performed at WERF. All radiological and nonradiological hazardous materials stored, used, or produced at WERF were identified and screened. Even though the screening process indicated that the hazardous materials could be screened from further analysis because the inventory of radiological and nonradiological hazardous materials were below the screening thresholds specified by DOE and DOE-ID guidance for DOE Order 5500.3A, the nonradiological hazardous materials were analyzed further because it was felt that the nonradiological hazardous material screening thresholds were too high.

Development of Neutron Probes for Characterization of Hazardous Materials in the Sub-surface Medium

International Nuclear Information System (INIS)

Keegan, R.P.; McGrath, C.A.; Lopez, J.C.

2002-01-01

Neutron probes are being developed at the Idaho National Engineering and Environmental Laboratory (INEEL) for the detection, identification and quantification of hazardous materials in the ground. Such materials include plutonium, uranium, americium, chlorine and fluorine. Both a Neutron Gamma (NG) probe and a Prompt Fission Neutron (PFN) probe are being developed. The NG probe is used primarily for nuclide identification and quantification measurements. The PFN is used mostly for the detection and measurement of fissile material, but also for the determination of thermal neutron macroscopic absorption cross sections of the various elements comprising the ground matrix. Calibration of these probes will be carried out at the INEEL using an indoor facility that has been designed for this activity

Hazardous waste: cleanup and prevention

Science.gov (United States)

Vandas, Stephen; Cronin, Nancy L.; Farrar, Frank; Serrano, Guillermo Eliezer Ávila; Yajimovich, Oscar Efraín González; Muñoz, Aurora R.; Rivera, María del C.

1996-01-01

Our lifestyles are supported by complex Industrial activities that produce many different chemicals and chemical wastes. The Industries that produce our clothing, cars, medicines, paper, food, fuels, steel, plastics, and electric components use and discard thousands of chemicals every year. At home we may use lawn chemicals, solvents, disinfectants, cleaners, and auto products to Improve our quality of life. A chemical that presents a threat or unreasonable risk to people or the environment Is a hazardous material. When a hazardous material can no longer be used, It becomes a hazardous waste. Hazardous wastes come from a variety of sources, from both present and past activities. Impacts to human health and the environment can result from Improper handling and disposal of hazardous waste.

Impacts of insufficient instructional materials on teaching biology: Higher education systems in focus

Directory of Open Access Journals (Sweden)

Sutuma Edessa

2017-01-01

Full Text Available Abstract The purpose of this study was to assess and determine impacts of insufficient instructional materials and ineffective lesson delivery methods on teaching in biology higher education. The participants of this study were 60 trainees who graduated in Bachelor of Sciences from eight public universities in majoring biology. Data for the study was collected while these trainees were attending the course of Biology Teaching Methods in the Post Graduate Diploma in Teaching, both in the regular and summer 2015/2016 training programs at Addis Ababa University. The study employs a mixed method design of both qualitative and quantitative data evaluations. Data was collected through classroom observations and interviews with the trainees. The findings indicated that insufficient instructional materials and ineffective teaching methods in higher education had negative impacts; that have affected the skills of performing biological tasks of graduates 71%. In the course of the Post Graduate Diploma in Teaching training, trainees were unsuccessful to conduct essential biological tasks expected from graduates of biology upon the completion of their undergraduate study program. The study was concluded with emphasis on the need to integrate theory and practice through using adequate instructional materials and proper teaching methods in the higher education biology teaching.

Instrumental neutron activation analysis for the certification of biological reference materials

International Nuclear Information System (INIS)

Ambulkar, M.N.; Chutke, N.L.; Garg, A.N.

1992-01-01

A multielemental instrumental neutron activation analysis (INAA) method by short and long irradiation has been employed for the determination of 22 minor and trace constituents in two proposed Standard Reference Materials P-RBF and P-WBF from Institute of Radioecology and Applied Nuclear Techniques, Czechoslovakia. Also some biological standards such as Bowen's Kale, Cabbage leaves (Poland) including wheat and rice flour samples of local origin were analysed. It is suggested that INAA is an ideal method for the certification of reference materials of biological matrices. (author). 7 refs., 1 tab

Pre Conference Hazardous Materials Workshop, West/East Coast Safety Conference, held 3-4 October/31 October - 1 November 1981,

Science.gov (United States)

1981-01-01

COMPATABILITY (2) PPE (3) SOP’s 𔃼 NOTES (1) USERDA ( RADIOACTIVE MATERIALS) (2) CHEMTREC (ALL OTHER HAZARDOUS MATERIALS) 2. NAVY A. NAVY ENVIRONMENTAL HEALTH...NRC Regulations for Packaging of Radioactive Material for Transport and Transportation of Radioactive Material Under Certain Conditions (10 CFR 71) V...NAVY) I DOD Directives/Instructions--- DOD Instruction 4120.14 DOD Water and Air Polution Abatement Policy DOD 4145.19R Series Storage and Material

Selecting the minimum risk route in the transportation of hazardous materials

Directory of Open Access Journals (Sweden)

Marijan Žura

1992-12-01

Full Text Available The transportation of hazardous materials is a broad and complex topic. Percent and iveight of accidents of vehicles carrying dangerous goods are growing fast. Modern computer based information system for dangerous materials management is becoming more and more important. In this paper I present an interactive software system for minimum risk route selection based on the PC ARC/INFO. The model computes optimal path based on accident probability is computed from traffic accident rates, highway operational speed, traffic volume and technical characteristic of the roadwidth, radius and slope. Dangerous goods are classified into nine classes according to their impact to different sensible environment elements. Those sensible elements are drinking water resourses, natural heritage, forestry, agricultural areas, cultural heritage, urban areas and tourist resorts. Some results of system implementation on Slovenia road network are be presented.

The environmental and medical geochemistry of potentially hazardous materials produced by disasters

Science.gov (United States)

Plumlee, Geoffrey S.; Morman, Suzette A.; Meeker, G.P.; Hoefen, Todd M.; Hageman, Philip L.; Wolf, Ruth E.

2014-01-01

Many natural or human-caused disasters release potentially hazardous materials (HM) that may pose threats to the environment and health of exposed humans, wildlife, and livestock. This chapter summarizes the environmentally and toxicologically significant physical, mineralogical, and geochemical characteristics of materials produced by a wide variety of recent disasters, such as volcanic eruptions, hurricanes and extreme storms, spills of mining/mineral-processing wastes or coal extraction by-products, and the 2001 attacks on and collapse of the World Trade Center towers. In describing these characteristics, this chapter also illustrates the important roles that geochemists and other earth scientists can play in environmental disaster response and preparedness. In addition to characterizing in detail the physical, chemical, and microbial makeup of HM generated by the disasters, these roles also include (1) identifying and discriminating potential multiple sources of the materials; (2) monitoring, mapping, and modeling dispersal and evolution of the materials in the environment; (3) understanding how the materials are modified by environmental processes; (4) identifying key characteristics and processes that influence the materials' toxicity to exposed humans and ecosystems; (5) estimating shifts away from predisaster environmental baseline conditions; and (6) using geochemical insights learned from past disasters to help estimate, prepare for, and increase societal resilience to the environmental and related health impacts of future disasters.

Radiological and hazardous material characterization report for the south portion of the 313 Building

International Nuclear Information System (INIS)

Harris, R.A.

1995-12-01

The objective of the characterization was to determine the extent of radiological contamination and presence of hazardous materials, to allow the preparation of an accurate cost estimate, and to plan for pre-demolition cleanup work to support building isolation. The scope of services for the project included the following tasks: Records Review and Interviews; Site Reconnaissance; Radiological Survey; and Sampling and Analysis

Biological evaluation of dental materials, in vitro and in vivo

International Nuclear Information System (INIS)

Kawahara, H.

1982-01-01

In this paper, the correlation between the user of tissue culture for in vitro tests and the tissue irritability and pupal response observed in in vitro tests, will be discussed. It would produce confusion if dental materials were standardised with the unreliable parameter of the living system in dynamic balance. Biological tests, both in vitro and in vivo, should be used for pre-standards testing, without any political control to establish physicochemical standards. As a first step, corrosion tests and the dissolution dosje of toxic components from the material in the tissue culture medium and/or artificial salvia should be standardised under conditions simulating the oral environment. The CNC method and photo-pattern analysis are used for the interpretation of cytotoxicity. The need for biological testing, both in vitro and in vivo, definitely exists in order to obtain physicochemical standards, with a biological simulation depending upon the feedback obtained from the results of in vitro and in vivo tests

Charged particle activation analysis of phosphorus in biological materials

International Nuclear Information System (INIS)

Masumoto, K.; Yagi, M.

1983-01-01

Charged particle activation analysis of phosphorus in biological materials using the 31 P(α,n) sup(34m)Cl reaction has been studied. Since sup(34m)Cl is also produced by the 32 S(α,pn) and the 35 Cl(α,α'n) reactions, the thick-target yield curves on phosphorus, sulfur and chlorine were determined in order to choose the optimum irradiation conditions. As a result, it was found that the activation analysis for phosphorus without interferences from sulfur and chlorine is possible by bombarding with less than 17 MeV alphas. The applicability of this method to biological samples was then examined by irradiating several standard reference materials. It was confirmed that phosphorus can readily be determined at the detection limit of 1μg free from interferences due to the matrix elements. (author)

Determination of mercury concentration in biological materials by neutron activation analysis

International Nuclear Information System (INIS)

Munoz, L.; Gras, N.; Cortes, E.; Cassorla, V.

1983-01-01

The objective of this work was to obtain a confident analytical method for measuring the mercury concentration in biological materials. Destructive neutron activation analysis was used for this purpose and a radiochemical separation method was studied to isolate the mercury from its main interferences: sodium and phosphorus, because these elements in biological materials are in high concentrations. The method developed was based on the copper amalgamation under controlled conditions. Yield and reproductibility studies were performed using 203 Hg as radioactive tracer. Finally, food samples of regular consumption were analyzed and the results were compared with those recommended by FAO/WHO. (Author)

The use of reference materials in the elemental analysis of biological samples

International Nuclear Information System (INIS)

Bowen, H.J.M.

1975-01-01

Reference materials (RMs) are useful to compare the accuracy and precision of laboratories and techniques. The desirable properties of biological reference materials are listed, and the problems of production, homogenization and storage described. At present there are only 10 biological RMs available compared with 213 geological and 520 metallurgical RMs. There is a need for more biological RMs including special materials for microprobe analysis and for in vivo activation analysis. A study of 650 mean values for elements in RM Kale, analysed by many laboratories, leads to the following conclusions. 61% of the values lie within +-10% of the best mean, and 80% lie within +-20% of the best mean. Atomic absorption spectrometry gives results that are 5-30% high for seven elements, while intrumental neutron activation analysis gives low and imprecise results for K. Other techniques with poor interlaboratory precision include neutron activation for Mg, polarography for Zn and arc-spectrometry for many elements. More than half the values for elements in Kale were obtained by neutron activation, confirming the importance of this technique and the need for RMs. As a rough estimate, 6 x 10 9 elemental analyses of biological materials are carried out each year, mostly by medical, agricultural and food scientists. It seems likely that a substantial percentage of these are inaccurate, a situation that might be improved by quality control using standard RMs. (author)

The preparation of four biological reference materials for QUASIMEME

NARCIS (Netherlands)

Leeuwen, van S.P.J.; Pieters, H.; Boer, de J.

2004-01-01

Four biological materials have been prepared for use in QUASIMEME interlaboratory studies including a shrimp sample for metal analysis (QM01-1) and two mussel (QO01-3 and QO02-2) and one mackerel sample (QO02-1) for organic contaminant analysis.

75 FR 45195 - Office of Hazardous Materials Safety; Notice of Applications for Modification of Special Permit

Science.gov (United States)

2010-08-02

... permits (e.g. to provide for additional hazardous materials, packaging design changes, additional mode of... compressed oxygen without rigid outer packaging when no other means of transportation exist. 14860-M Alaska... authorizing the transportation in commerce of compressed oxygen without rigid outer packaging when no other...

Perception and prevalence of work-related health hazards among health care workers in public health facilities in southern India.

Science.gov (United States)

Senthil, Arasi; Anandh, Balasubramanian; Jayachandran, Palsamy; Thangavel, Gurusamy; Josephin, Diana; Yamini, Ravindran; Kalpana, Balakrishnan

2015-01-01

Health care workers (HCWs) are exposed to occupational related health hazards. Measuring worker perception and the prevalence of these hazards can help facilitate better risk management for HCWs, as these workers are envisaged to be the first point of contact, especially in resource poor settings. To describe the perception of occupational health hazards and self-reported exposure prevalence among HCWs in Southern India. We used cross sectional design with stratified random sampling of HCWs from different levels of health facilities and categories in a randomly selected district in Southern India. Data on perception and exposure prevalence were collected using a structured interview schedule developed by occupational health experts and administered by trained investigators. A total of 482 HCWs participated. Thirty nine percent did not recognize work-related health hazards, but reported exposure to at least one hazard upon further probing. Among the 81·5% who reported exposure to biological hazard, 93·9% had direct skin contact with infectious materials. Among HCWs reporting needle stick injury, 70·5% had at least one in the previous three months. Ergonomic hazards included lifting heavy objects (42%) and standing for long hours (37%). Psychological hazards included negative feelings (20·3%) and verbal or physical abuse during work (20·5%). More than a third of HCWs failed to recognize work-related health hazards. Despite training in handling infectious materials, HCWs reported direct skin contact with infectious materials and needle stick injuries. RESULTS indicate the need for training oriented toward behavioral change and provision of occupational health services.

Assessment of natural radioactivity and radiological hazards in building materials used in the Tiruvannamalai District, Tamilnadu, India, using a statistical approach

Directory of Open Access Journals (Sweden)

Y. Raghu

2017-07-01

Full Text Available One-hundred-fifty-one samples of six types of building materials were collected from different locations of the Tiruvannamalai District, Tamilnadu, and were analyzed using a gamma ray spectroscopy system. From the results, the highest values observed in the specific activities of 226Ra, 232Th and 40K were 116.1 (soil 106.67 (sand and 527.533 (tiles in Bq kg−1, while the lowest values observed in the specific activities of the same radionuclides were 35.73, 37.75 and 159.83 for cement in Bq kg−1, respectively. The potential radiological hazards were assessed by calculating the radium equivalent activity (Raeq, the indoor absorbed gamma dose rate (DR, the annual effective dose rate (HR, the activity utilization index (I, the alpha index (Iα, the gamma index (Iγ, and the external hazard (Hex and internal hazard (Hin indices. The estimated mean value of the absorbed dose rate of 148.35 nGy h−1 is slightly higher than the world average value of 84 nGy h−1, and the annual effective dose in the studied samples is 0.1824 mSv y−1, which is lower than the recommended limit. Multivariate statistical methods are applied to determine the existing relationship between radionuclides and radiological health hazard parameters and to identify the maximum contribution of radionuclide in radioactivity. The values of the hazard indices were below the recommended levels; therefore, it is concluded that the buildings constructed from such materials are safe for the inhabitants. The findings from this research will be useful to assess the radiation hazards of building materials in humans.

EFSA Panels on Biological Hazards (BIOHAZ), on Contaminants in the Food Chain (CONTAM), and on Animal Health and Welfare (AHAW); Scientific Opinion on the public health hazards to be covered by inspection of meat (poultry)

DEFF Research Database (Denmark)

Hald, Tine

2012-01-01

be risk categorisation of flocks based on FCI and classification of abattoirs according to their capability to reduce carcass faecal contamination. It is proposed that post-mortem visual inspection is replaced by setting targets for the main hazards on the carcass, and by verification of the food business......A qualitative risk assessment identified Campylobacter spp., Salmonella spp. and ESBL/AmpC gene-carrying bacteria as the most relevant biological hazards in the context of meat inspection of poultry. As none of these are detected by traditional visual meat inspection, establishing an integrated...... food safety assurance system, achievable through improved food chain information (FCI) and risk-based interventions, was proposed. This includes setting targets at carcass level and, when appropriate, flock level indicating what should be achieved for a given hazard. Elements of the system would...

Flotation of Biological Materials

Directory of Open Access Journals (Sweden)

George Z. Kyzas

2014-03-01

Full Text Available Flotation constitutes a gravity separation process, which originated from the minerals processing field. However, it has, nowadays, found several other applications, as for example in the wastewater treatment field. Concerning the necessary bubble generation method, typically dispersed-air or dissolved-air flotation was mainly used. Various types of biological materials were tested and floated efficiently, such as bacteria, fungi, yeasts, activated sludge, grape stalks, etc. Innovative processes have been studied in our Laboratory, particularly for metal ions removal, involving the initial abstraction of heavy metal ions onto a sorbent (including a biosorbent: in the first, the application of a flotation stage followed for the efficient downstream separation of metal-laden particles. The ability of microorganisms to remove metal ions from dilute aqueous solutions (as most wastewaters are is a well-known property. The second separation process, also applied effectively, was a new hybrid cell of microfiltration combined with flotation. Sustainability in this field and its significance for the chemical and process industry is commented.

Biological export of radioactive materials from a leaching pond in SE Idaho

International Nuclear Information System (INIS)

Millard, Jere B.

1978-01-01

A radioecological investigation was conducted to quantify biological export of radioactive materials from a test reactor area leaching pond located on the Idaho National Engineering Laboratory site in southeast Idaho. An estimated 42,000 Ci have been discharged to the pond since 1952. Approximately 35 gamma emitting radionuclides are detectable in unfiltered water. Biomass estimates and mean radionuclide concentrations were determined for major pond compartments. A radionuclide inventory of the pond ecosystem was constructed listing totals for radioactivity present in each compartment. Mean concentrations of predominant radionuclides and population census data were used to estimate biologically exported materials. Particular attention was paid to migrant waterfowl, a resident population of barn swallows (Hirundo rustica), and nesting shore birds. Whole body gamma spectra indicated 15 or more detectable fission and activation products associated with swallows and shore birds, and 20 or more for waterfowl. Concentration factors relative to filtered pond water were also calculated. Finally, biologically exported radioactive materials were compared with total amounts present in the pond. (author)

Theory of light transfer in food and biological materials

Science.gov (United States)

In this chapter, we first define the basic radiometric quantities that are needed for describing light propagation in food and biological materials. Radiative transfer theory is then derived, according to the principle of the conservation of energy. Because the radiative transfer theory equation is ...

Occupational health hazards in mining: an overview

Energy Technology Data Exchange (ETDEWEB)

Donoghue, A.M. [Alcoa World Alumina Australia, Perth, WA (Australia)

2004-08-01

This review article outlines the physical, chemical, biological, ergonomic and psychosocial occupational health hazards of mining and associated metallurgical processes. Mining remains an important industrial sector in many parts of the world and although substantial progress has been made in the control of occupational health hazards, there remains room for further risk reduction. This applies particularly to traumatic injury hazards, ergonomic hazards and noise. Vigilance is also required to ensure exposures to coal dust and crystalline silica remain effectively controlled.

75 FR 57830 - Office of Hazardous Materials Safety; Notice of Applications for Modification of Special Permit

Science.gov (United States)

2010-09-22

... permits (e.g. to provide for additional hazardous materials, packaging design changes, additional mode of... special permit Application No. Docket No. Applicant affected thereof 7951-M ConAgra Foods, 49 CFR To... outer packaging when no other means of transportation exist. 14953-M Applied 49 CFR To modify the...

Assessment of natural radioactivity and the associated radiation hazards in some Cameroonian building materials

International Nuclear Information System (INIS)

Ngachin, M.; Garavaglia, M.; Giovani, C.; Kwato Njock, M.G.

2005-09-01

The concentration of 238 U, 232 Th, 40 K in natural and fabricated building materials used in Cameroon was investigated by a high-resolution γ-ray spectrometry system with a co-axial HPGe detector. Fourteen kinds of building materials were collected from factories and in the field. Each sample was therefore kept in a 500 ml plastic Marinelli beakers and measured in a very low-background laboratory. The measured activity concentrations range from 1.76 to 49.84 Bq kg -1 , from 0.32 to 147.2 Bq kg -1 and from 18.16 to 1226.29 Bq kg -1 for 238 U, 232 Th and 40 K respectively. The highest mean value of 238 U concentration was found in red compressed soil-brick type I (49.57±0.33 Bq kg -1 ) produced by MIPROMALO whereas the highest average concentration of 232 Th (138.89±12.51 Bq kg -1 ) and 40 K (1161.46±107.57 Bq kg -1 ) was found in gravel collected from an exploitation site in LOGBADJECK. The activity concentrations obtained were compared with available data from other investigations and with the world average value for soils. The radium equivalent activity Ra eq , the external hazard index H ex as well as the indoor absorbed dose rate D radical in air and the annual effective dose equivalent H radical E were evaluated to assess the radiation hazards for people living in dwellings made of studied materials. All building materials have shown Ra eq activity (range from 10.15 to 312.57 Bq kg -1 ) lower than the limit of 370 Bq kg -1 set in the Organization for Economic Cooperation and Development (OECD, 1979) report, and which is equivalent to a γ-dose of 1.5 mSv yr -1 All the examined materials are acceptable for use as building materials in accord with the OECD criterion. (author)

Functional design criteria for the Hazardous Materials Management and Emergency Response (HAMMER) Training Center. Revision 1

International Nuclear Information System (INIS)

Sato, P.K.

1995-01-01

Within the United States, there are few hands-on training centers capable of providing integrated technical training within a practical application environment. Currently, there are no training facilities that offer both radioactive and chemical hazardous response training. There are no hands-on training centers that provide training for both hazardous material operations and emergency response that also operate as a partnership between organized labor, state agencies, tribes, and local emergency responders within the US Department of Energy (DOE) complex. Available facilities appear grossly inadequate for training the thousands of people at Hanford, and throughout the Pacific Northwest, who are required to qualify under nationally-mandated requirements. It is estimated that 4,000 workers at the Hanford Site alone need hands-on training. Throughout the Pacific Northwest, the potential target audience would be over 30,000 public sector emergency response personnel, as well as another 10,000 clean-up workers represented by organized labor. The HAMMER Training Center will be an interagency-sponsored training center. It will be designed, built, and operated to ensure that clean-up workers, fire fighters, and public sector management and emergency response personnel are trained to handle accidental spills of hazardous materials. Training will cover wastes at clean-up sites, and in jurisdictions along the transportation corridors, to effectively protect human life, property, and the environment

Transport of hazardous goods

International Nuclear Information System (INIS)

1989-01-01

The course 'Transport of hazardous goods' was held in Berlin in November 1988 in cooperation with the Bundesanstalt fuer Materialforschung und -pruefung. From all lecturs, two are recorded separately: 'Safety of tank trucks - requirements on the tank, development possibiities of active and passive safety' and 'Requirements on the transport of radioactive materials - possible derivations for other hazardous goods'. The other lectures deal with hazardous goods law, requirements on packinging, risk assessment, railroad transport, hazardous goods road network, insurance matters, EC regulations, and waste tourism. (HSCH) [de

Environmental Assessment For the Proposed Construction of A Hazardous Materials Issue Facility and a Hazardous Wastes Storage Facility at Buckley Air Force Base, Colorado

Science.gov (United States)

2005-04-01

hazardous materials in accordance with the Occupational Health and Safety Administration ( OSHA ) storage standards. This facility would make the...subcontinent including, for example, Cambodia, China, India, Japan, Korea, Malaysia , Pakistan, or the Philippine Islands; and • Native Hawaiian and Other...regulated by the USEPA and the OSHA . The state of Colorado also has regulations pertaining to ACM abatement. Emissions of asbestos fibers into the

The National Shipbuilding Research Program, 1990 Ship Production Symposium, Paper No. 4B-1: Solving SARA Compliance with Computerized Hazardous Materials Tracking

National Research Council Canada - National Science Library

Johnston, Don; Schoenleber, Dave

1990-01-01

...) has forced facilities to keep track of hazardous materials as never before. EPCRA contains five major reporting requirements including planning notification, emergency release notification, Material Safety Data Sheet (MSDS...

Hazardous materials in aquatic environments of the Mississippi River Basin

International Nuclear Information System (INIS)

1993-01-01

Tulane and Xavier Universities have singled out the environment as a major strategic focus for research and training for now and by the year 2000. In December, 1992, the Tulane/Xavier CBR was awarded a five year grant to study pollution in the Mississippi River system. The ''Hazardous Materials in Aquatic Environments of the Mississippi River Basin'' project is a broad research and education program aimed at elucidating the nature and magnitude of toxic materials that contaminate aquatic environments of the Mississippi River Basin. Studies include defining the complex interactions that occur during the transport of contaminants, the actual and potential impact on ecological systems and health, and the mechanisms through which these impacts might be remediated. The Mississippi River Basin represents a model system for analyzing and solving contamination problems that are found in aquatic systems world-wide. These research and education projects are particularly relevant to the US Department of Energy's programs aimed at addressing aquatic pollution problems associated with DOE National Laboratories. First year funding supported seven collaborative cluster projects and twelve initiation projects. This report summarizes research results for period December 1992--December 1993

Biologically inspired autonomous structural materials with controlled toughening and healing

Science.gov (United States)

Garcia, Michael E.; Sodano, Henry A.

2010-04-01

The field of structural health monitoring (SHM) has made significant contributions in the field of prognosis and damage detection in the past decade. The advantageous use of this technology has not been integrated into operational structures to prevent damage from propagating or to heal injured regions under real time loading conditions. Rather, current systems relay this information to a central processor or human operator, who then determines a course of action such as altering the mission or scheduling repair maintenance. Biological systems exhibit advanced sensory and healing traits that can be applied to the design of material systems. For instance, bone is the major structural component in vertebrates; however, unlike modern structural materials, bone has many properties that make it effective for arresting the propagation of cracks and subsequent healing of the fractured area. The foremost goal for the development of future adaptive structures is to mimic biological systems, similar to bone, such that the material system can detect damage and deploy defensive traits to impede damage from propagating, thus preventing catastrophic failure while in operation. After sensing and stalling the propagation of damage, the structure must then be repaired autonomously using self healing mechanisms motivated by biological systems. Here a novel autonomous system is developed using shape memory polymers (SMPs), that employs an optical fiber network as both a damage detection sensor and a network to deliver stimulus to the damage site initiating adaptation and healing. In the presence of damage the fiber optic fractures allowing a high power laser diode to deposit a controlled level of thermal energy at the fractured sight locally reducing the modulus and blunting the crack tip, which significantly slows the crack growth rate. By applying a pre-induced strain field and utilizing the shape memory recovery effect, thermal energy can be deployed to close the crack and return

[The meaning of accidents with biological material to nursing professionals].

Science.gov (United States)

Magagnini, Maristela Aparecida Magri; Rocha, Suelen Alves; Ayres, Jairo Aparecido

2011-06-01

The aim of this study is to understand what meaning work accidents with exposure to biological material has to nurses. This is an exploratory study with a qualitative approach, and it used Bardin's content analysis. 87 accidents with biological material occurred in the period between 2001 and 2006; among them, eight were seropositive for Hepatitis B and C and HIV/AIDS. An interview with guiding questions was used to collect data. When inquiring these professionals about the meaning of these accidents, four categories emerged: risk situation, danger perception, fatality, and feelings. Although it is not a strategy of clarification, it is a fact that work organization and educative actions have considerable impact in reducing this type of accident, also reducing damage to the life of nurses involved in these accidents.

Biological and chemical sensors based on graphene materials.

Science.gov (United States)

Liu, Yuxin; Dong, Xiaochen; Chen, Peng

2012-03-21

Owing to their extraordinary electrical, chemical, optical, mechanical and structural properties, graphene and its derivatives have stimulated exploding interests in their sensor applications ever since the first isolation of free-standing graphene sheets in year 2004. This article critically and comprehensively reviews the emerging graphene-based electrochemical sensors, electronic sensors, optical sensors, and nanopore sensors for biological or chemical detection. We emphasize on the underlying detection (or signal transduction) mechanisms, the unique roles and advantages of the used graphene materials. Properties and preparations of different graphene materials, their functionalizations are also comparatively discussed in view of sensor development. Finally, the perspective and current challenges of graphene sensors are outlined (312 references).

Fuel from biologic wase materials; Kraftstoff aus biologischen Reststoffen

Energy Technology Data Exchange (ETDEWEB)

Braesel, Martina

2013-06-01

In Germany, annually about 770,000 tons of biological waste reach rubbish bins or composting plants. In order to recondition this biological waste, the Federal Ministry of Education and Research (Berlin, Federal Republic of Germany) has launched a research project with a funding of 4.3 million Euro limited to a period of time of five years. In cooperation with the Fraunhofer Institute for Interfacial Engineering and Biotechnology (Stuttgart, Federal Republic of Germany) easily fermentable, wet biomass with a low content of lignocellulosic material has to be completely transformed to biogas with maximum energy. Only some of the ash remains.

Social justice and research using human biological material: A ...

African Journals Online (AJOL)

Social justice and research using human biological material: A response to Mahomed, Nöthling-Slabbert and Pepper. ... South African Medical Journal ... In a recent article, Mahomed, Nöthling-Slabbert and Pepper proposed that research participants should be entitled to share in the profits emanating from such research ...

Application of pristine and doped SnO2 nanoparticles as a matrix for agro-hazardous material (organophosphate) detection

Science.gov (United States)

Khan, Naushad; Athar, Taimur; Fouad, H.; Umar, Ahmad; Ansari, Z. A.; Ansari, S. G.

2017-02-01

With an increasing focus on applied research, series of single/composite materials are being investigated for device development to detect several hazardous, dangerous, and toxic molecules. Here, we report a preliminary attempt of an electrochemical sensor fabricated using pristine Ni and Cr-doped nano tin oxide material (SnO2) as a tool to detect agro-hazardous material, i.e. Organophosphate (OP, chlorpyrifos). The nanomaterial was synthesized using the solution method. Nickel and chromium were used as dopant during synthesis. The synthesized material was calcined at 1000 °C and characterized for morphological, structural, and elemental analysis that showed the formation of agglomerated nanosized particles of crystalline nature. Screen-printed films of powder obtained were used as a matrix for working electrodes in a cyclic voltammogram (CV) at various concentrations of organophosphates (0.01 to 100 ppm). The CV curves were obtained before and after the immobilization of acetylcholinesterase (AChE) on the nanomaterial matrix. An interference study was also conducted with hydroquinone to ascertain the selectivity. The preliminary study indicated that such material can be used as suitable matrix for a device that can easily detect OP to a level of 10 ppb and thus contributes to progress in terms of desired device technology for the food and agricultural-industries.

Creating biological nanomaterials using synthetic biology

International Nuclear Information System (INIS)

Rice, MaryJoe K; Ruder, Warren C

2014-01-01

Synthetic biology is a new discipline that combines science and engineering approaches to precisely control biological networks. These signaling networks are especially important in fields such as biomedicine and biochemical engineering. Additionally, biological networks can also be critical to the production of naturally occurring biological nanomaterials, and as a result, synthetic biology holds tremendous potential in creating new materials. This review introduces the field of synthetic biology, discusses how biological systems naturally produce materials, and then presents examples and strategies for incorporating synthetic biology approaches in the development of new materials. In particular, strategies for using synthetic biology to produce both organic and inorganic nanomaterials are discussed. Ultimately, synthetic biology holds the potential to dramatically impact biological materials science with significant potential applications in medical systems. (review)

Creating biological nanomaterials using synthetic biology.

Science.gov (United States)

Rice, MaryJoe K; Ruder, Warren C

2014-02-01

Synthetic biology is a new discipline that combines science and engineering approaches to precisely control biological networks. These signaling networks are especially important in fields such as biomedicine and biochemical engineering. Additionally, biological networks can also be critical to the production of naturally occurring biological nanomaterials, and as a result, synthetic biology holds tremendous potential in creating new materials. This review introduces the field of synthetic biology, discusses how biological systems naturally produce materials, and then presents examples and strategies for incorporating synthetic biology approaches in the development of new materials. In particular, strategies for using synthetic biology to produce both organic and inorganic nanomaterials are discussed. Ultimately, synthetic biology holds the potential to dramatically impact biological materials science with significant potential applications in medical systems.

Study on hazardous substances contained in radioactive waste

International Nuclear Information System (INIS)

Kuroki, Ryoichiro; Takahashi, Kuniaki

2008-01-01

It is necessary that the technical criteria is established concerning waste package for disposal of the TRU waste generated in Japan Atomic Energy Agency. And it is important to consider the criteria not only in terms of radioactivity but also in terms of chemical hazard and criticality. Therefore the environmental impact of hazardous materials and possibility of criticality were investigated to decide on technical specification of radioactive waste packages. The contents and results are as following. (1) Concerning hazardous materials included in TRU waste, regulations on disposal of industrial wastes and on environmental preservation were investigated. (2) The assessment methods for environmental impact of hazardous materials included in radioactive waste in U.K, U.S.A. and France were investigated. (3) The parameters for mass transport assessment about migration of hazardous materials in waste packages around disposal facilities were compiled. And the upper limits of amounts of hazardous materials in waste packages to satisfy the environmental standard were calculated with mass transport assessment for some disposal concepts. (4) It was suggested from criticality analysis for waste packages in disposal facility that the occurrence of criticality was almost impossible under the realistic conditions. (author)

Transportation of radioactive, hazardous, and mixed wastes: Material identification is the key

International Nuclear Information System (INIS)

Stancell, D.F.; Willaford, D.M.

1992-01-01

This paper will discuss how material identification and classification will result in an accurate determination of regulatory requirements, and will assure safe and compliant shipment of radioactive, hazardous, and mixed wastes. The primary focus of the paper is a discussion of lessons learned by the Department of Energy in making waste shipments, and how this can be applied to future mixed waste shipments. There will be a brief discussion of the Department's regulatory compliance program, including a presentation of compliance audit results, and how regulatory issues are addressed through effective information exchange, technical assistance, and compliance training. A detailed discussion will follow, which describes cases involving material identification and classification problems. Examples will include both RCRA waste and uranium mill tailings shipments. The paper will conclude with a discussion concerning the application of these lessons to future mixed waste shipments proposed by the Department. (author)

''Hazardous'' terminology

International Nuclear Information System (INIS)

Powers, J.

1991-01-01

A number of terms (e.g., ''hazardous chemicals,'' ''hazardous materials,'' ''hazardous waste,'' and similar nomenclature) refer to substances that are subject to regulation under one or more federal environmental laws. State laws and regulations also provide additional, similar, or identical terminology that may be confused with the federally defined terms. Many of these terms appear synonymous, and it easy to use them interchangeably. However, in a regulatory context, inappropriate use of narrowly defined terms can lead to confusion about the substances referred to, the statutory provisions that apply, and the regulatory requirements for compliance under the applicable federal statutes. This information Brief provides regulatory definitions, a brief discussion of compliance requirements, and references for the precise terminology that should be used when referring to ''hazardous'' substances regulated under federal environmental laws. A companion CERCLA Information Brief (EH-231-004/0191) addresses ''toxic'' nomenclature

Preliminary hazards analysis -- vitrification process

International Nuclear Information System (INIS)

Coordes, D.; Ruggieri, M.; Russell, J.; TenBrook, W.; Yimbo, P.

1994-06-01

This paper presents a Preliminary Hazards Analysis (PHA) for mixed waste vitrification by joule heating. The purpose of performing a PHA is to establish an initial hazard categorization for a DOE nuclear facility and to identify those processes and structures which may have an impact on or be important to safety. The PHA is typically performed during and provides input to project conceptual design. The PHA is then followed by a Preliminary Safety Analysis Report (PSAR) performed during Title 1 and 2 design. The PSAR then leads to performance of the Final Safety Analysis Report performed during the facility's construction and testing. It should be completed before routine operation of the facility commences. This PHA addresses the first four chapters of the safety analysis process, in accordance with the requirements of DOE Safety Guidelines in SG 830.110. The hazards associated with vitrification processes are evaluated using standard safety analysis methods which include: identification of credible potential hazardous energy sources; identification of preventative features of the facility or system; identification of mitigative features; and analyses of credible hazards. Maximal facility inventories of radioactive and hazardous materials are postulated to evaluate worst case accident consequences. These inventories were based on DOE-STD-1027-92 guidance and the surrogate waste streams defined by Mayberry, et al. Radiological assessments indicate that a facility, depending on the radioactive material inventory, may be an exempt, Category 3, or Category 2 facility. The calculated impacts would result in no significant impact to offsite personnel or the environment. Hazardous materials assessment indicates that a Mixed Waste Vitrification facility will be a Low Hazard facility having minimal impacts to offsite personnel and the environment

Preliminary hazards analysis -- vitrification process

Energy Technology Data Exchange (ETDEWEB)

Coordes, D.; Ruggieri, M.; Russell, J.; TenBrook, W.; Yimbo, P. [Science Applications International Corp., Pleasanton, CA (United States)

1994-06-01

This paper presents a Preliminary Hazards Analysis (PHA) for mixed waste vitrification by joule heating. The purpose of performing a PHA is to establish an initial hazard categorization for a DOE nuclear facility and to identify those processes and structures which may have an impact on or be important to safety. The PHA is typically performed during and provides input to project conceptual design. The PHA is then followed by a Preliminary Safety Analysis Report (PSAR) performed during Title 1 and 2 design. The PSAR then leads to performance of the Final Safety Analysis Report performed during the facility`s construction and testing. It should be completed before routine operation of the facility commences. This PHA addresses the first four chapters of the safety analysis process, in accordance with the requirements of DOE Safety Guidelines in SG 830.110. The hazards associated with vitrification processes are evaluated using standard safety analysis methods which include: identification of credible potential hazardous energy sources; identification of preventative features of the facility or system; identification of mitigative features; and analyses of credible hazards. Maximal facility inventories of radioactive and hazardous materials are postulated to evaluate worst case accident consequences. These inventories were based on DOE-STD-1027-92 guidance and the surrogate waste streams defined by Mayberry, et al. Radiological assessments indicate that a facility, depending on the radioactive material inventory, may be an exempt, Category 3, or Category 2 facility. The calculated impacts would result in no significant impact to offsite personnel or the environment. Hazardous materials assessment indicates that a Mixed Waste Vitrification facility will be a Low Hazard facility having minimal impacts to offsite personnel and the environment.

Hydrothermal Liquefaction Treatment Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-09-12

Hazard analyses were performed to evaluate the modular hydrothermal liquefaction treatment system. The hazard assessment process was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. The analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public. The following selected hazardous scenarios received increased attention: •Scenarios involving a release of hazardous material or energy, controls were identified in the What-If analysis table that prevent the occurrence or mitigate the effects of the release. •Scenarios with significant consequences that could impact personnel outside the immediate operations area, quantitative analyses were performed to determine the potential magnitude of the scenario. The set of “critical controls” were identified for these scenarios (see Section 4) which prevent the occurrence or mitigate the effects of the release of events with significant consequences.

Sustainable System for Residual Hazards Management

International Nuclear Information System (INIS)

Kevin M. Kostelnik; James H. Clarke; Jerry L. Harbour

2004-01-01

Hazardous, radioactive and other toxic substances have routinely been generated and subsequently disposed of in the shallow subsurface throughout the world. Many of today's waste management techniques do not eliminate the problem, but rather only concentrate or contain the hazardous contaminants. Residual hazards result from the presence of hazardous and/or contaminated material that remains on-site following active operations or the completion of remedial actions. Residual hazards pose continued risk to humans and the environment and represent a significant and chronic problem that require continuous long-term management (i.e. >1000 years). To protect human health and safeguard the natural environment, a sustainable system is required for the proper management of residual hazards. A sustainable system for the management of residual hazards will require the integration of engineered, institutional and land-use controls to isolate residual contaminants and thus minimize the associated hazards. Engineered controls are physical modifications to the natural setting and ecosystem, including the site, facility, and/or the residual materials themselves, in order to reduce or eliminate the potential for exposure to contaminants of concern (COCs). Institutional controls are processes, instruments, and mechanisms designed to influence human behavior and activity. System failure can involve hazardous material escaping from the confinement because of system degradation (i.e., chronic or acute degradation) or by external intrusion of the biosphere into the contaminated material because of the loss of institutional control. An ongoing analysis of contemporary and historic sites suggests that the significance of the loss of institutional controls is a critical pathway because decisions made during the operations/remedial action phase, as well as decisions made throughout the residual hazards management period, are key to the long-term success of the prescribed system. In fact

Routine Determination of Arsenic in Biological Materials. RCN Report

International Nuclear Information System (INIS)

Kroon, J.J.; Das, H.A.

1970-08-01

This text describes a routine procedure for the determination of arsenic in biological materials by neutron activation analysis. Unlike most methods published in literature the present analysis is not based on chemical separation by destination. After a first purification by anion-exchange the 76 As-activity (T1/2 = 26,4 h) is isolated by precipitation as the metal. The method was tested by analysis of the standard kale powder. This material was prepared and issued by Bowen in 1966, to provide a reliable standard for the intercomparison of various methods. (author)

Chemical preparation of biological materials for accurate chromium determination by isotope dilution mass spectrometry

International Nuclear Information System (INIS)

Dunstan, L.P.; Garner, E.L.

1977-01-01

The current interest in trace elements in biological materials has created a need for accurate methods of analysis. The source of discrepancies and variations in chromium concentration determinations is often traceable to inadequate methods of sample preparation. Any method of Cr analysis that requires acid digestion of a biological matrix must take into consideration the existence or formation of a volatile Cr component. In addition, because Cr is often present at concentrations less than 1 μg/g, the analytical blank becomes a potential source of error. Chemical procedures have been developed for the digestion of the biological matrix and the separation of Cr without either large analytical blanks or significant losses by volatilization. These procedures have been used for the analysis of NBS Standard Reference Material (SRM) 1569 Brewers Yeast; SRM 1577 Bovine Liver; SRM 1570 Spinach and other biological materials including human hair and nails. At this time, samples containing 1 μg of Cr can be determined with an estimated accuracy of 2 percent

75 FR 34573 - Bulk Solid Hazardous Materials: Harmonization With the International Maritime Solid Bulk Cargoes...

Science.gov (United States)

2010-06-17

... reduced iron (DRI) as briquettes molded at a temperature of 650 [deg]C or higher that have a density of 5... temperature of 650 [deg]C or higher or had a density of 5.0 g/cm[sup3] or greater. In this proposed rule, we... bulk materials of Hazard Classes 4 through 9. c. One comment recommended that a DCM be required for...

78 FR 41853 - Safety Advisory Guidance: Heating Rail Tank Cars To Prepare Hazardous Material for Unloading or...

Science.gov (United States)

2013-07-12

... rail tank car due to chemical self-reaction and expansion of the toluene diisocyanate matter wastes. On...: Cheryl West Freeman, Division of Engineering and Research, Pipeline and Hazardous Materials Safety... catastrophically ruptured at a transfer station at the BASF Corporation chemical facility in Freeport, Texas. The...

Proposal of risk evaluation methodology for hazardous materials transportation

International Nuclear Information System (INIS)

Hartman, Luiz Carlos

2009-01-01

The increasing concern with the level of risk associated with the transportation of hazardous materials took some international institutions to pledge efforts in the evaluation of risk in regional level. Following this trend, the objective of this work was to analyze the most recent processes of analysis of risks from road transportation of hazardous materials. In the present work 21 methodologies of analysis of risks, developed by some authors and for diverse localities have been evaluated. Two of them, in special, have been reviewed and discussed: a method recently developed by the Swiss Federal Institute of Technology (Nicolet-Monnier and Gheorghe, 1996) and the strategy delineated by the Center for Chemical Process Safety CCPS (1995), taking into consideration the estimate of the individual and social risk. Also, the models of Harwood et al. (1990) and of Ramos (1997), adapted by Hartman (2003) have been applied to the reality of the roads of the state of Sao Paulo. The extension of these methodologies was explored, in order to find its advantages and disadvantages. As a study case the present work considered the ammonia transportation throughout two routes evaluating the reality of the roads of the state of Sao Paulo, including a significant parcel of evaluation in a densely populated area, getting the results using risk, at least, one of the methodologies mentioned above. The innovation proposed by this work was the research, the development and the introduction of two variables to the model considered by Harwood et al. (1990). These variables that influence in the value of the risk are: the age of the driver of truck and the zone of impact that is function type of product, period of the day where the transport was carried and the volume that has been transported. The aim of the proposed modifications is to let the value of the risk more sensible in relation to the type of the product carried and the age of the truck driver. The main related procedural stages

Sampling and sample preparation methods for the analysis of trace elements in biological material

International Nuclear Information System (INIS)

Sansoni, B.; Iyengar, V.

1978-05-01

The authors attempt to give a most systamtic possible treatment of the sample taking and sample preparation of biological material (particularly in human medicine) for trace analysis (e.g. neutron activation analysis, atomic absorption spectrometry). Contamination and loss problems are discussed as well as the manifold problems of the different consistency of solid and liquid biological materials, as well as the stabilization of the sample material. The process of dry and wet ashing is particularly dealt with, where new methods are also described. (RB) [de

Determination of trace elements in biological material by neutron activation analysis

International Nuclear Information System (INIS)

Tran Van, L.; Teherani, D.K.

1989-01-01

Eighteen trace elements in biological materials [grass (Imperata cylindrica), mimosa plant (Mimosa pudica), rice] by neutron activation method were determined. In the comparative analysis the content of the same element was different in each material, although they were collected at the same place and the same sampling method was applied. (author) 4 refs.; 1 fig.; 1 tab

Protective Behaviour of Citizens to Transport Accidents Involving Hazardous Materials: A Discrete Choice Experiment Applied to Populated Areas nearby Waterways.

Directory of Open Access Journals (Sweden)

Esther W de Bekker-Grob

Full Text Available To improve the information for and preparation of citizens at risk to hazardous material transport accidents, a first important step is to determine how different characteristics of hazardous material transport accidents will influence citizens' protective behaviour. However, quantitative studies investigating citizens' protective behaviour in case of hazardous material transport accidents are scarce.A discrete choice experiment was conducted among subjects (19-64 years living in the direct vicinity of a large waterway. Scenarios were described by three transport accident characteristics: odour perception, smoke/vapour perception, and the proportion of people in the environment that were leaving at their own discretion. Subjects were asked to consider each scenario as realistic and to choose the alternative that was most appealing to them: staying, seeking shelter, or escaping. A panel error component model was used to quantify how different transport accident characteristics influenced subjects' protective behaviour.The response was 44% (881/1,994. The predicted probability that a subject would stay ranged from 1% in case of a severe looking accident till 62% in case of a mild looking accident. All three transport accident characteristics proved to influence protective behaviour. Particularly a perception of strong ammonia or mercaptan odours and visible smoke/vapour close to citizens had the strongest positive influence on escaping. In general, 'escaping' was more preferred than 'seeking shelter', although stated preference heterogeneity among subjects for these protective behaviour options was substantial. Males were less willing to seek shelter than females, whereas elderly people were more willing to escape than younger people.Various characteristics of transport accident involving hazardous materials influence subjects' protective behaviour. The preference heterogeneity shows that information needs to be targeted differently depending on

Hazards assessment for the INEL Landfill Complex

International Nuclear Information System (INIS)

Knudsen, J.K.; Calley, M.B.

1994-02-01

This report documents the hazards assessment for the INEL Landfill Complex (LC) located at the Idaho National Engineering Laboratory, which is operated by EG ampersand G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and the DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes the hazards that are significant enough to warrant consideration in a facility's operational emergency management program. The area surrounding the LC, the buildings and structures at the LC, and the processes that are used at the LC are described in this report. All hazardous materials, both radiological and nonradiological, at the LC were identified and screened against threshold quantities according to DOE Order 5500.3A guidance. Asbestos at the Asbestos Pit was the only hazardous material that exceeded its specified threshold quantity. However, the type of asbestos received and the packaging practices used are believed to limit the potential for an airborne release of asbestos fibers. Therefore, in accordance with DOE Order 5500.3A guidance, no further hazardous material characterization or analysis was required for this hazards assessment

Hazards assessment for the INEL Landfill Complex

Energy Technology Data Exchange (ETDEWEB)

Knudsen, J.K.; Calley, M.B.

1994-02-01

This report documents the hazards assessment for the INEL Landfill Complex (LC) located at the Idaho National Engineering Laboratory, which is operated by EG&G Idaho, Inc., for the US Department of Energy (DOE). The hazards assessment was performed to ensure that this facility complies with DOE and company requirements pertaining to emergency planning and preparedness for operational emergencies. DOE Order 5500.3A requires that a facility-specific hazards assessment be performed to provide the technical basis for facility emergency planning efforts. This hazards assessment was conducted in accordance with DOE Headquarters and the DOE Idaho Operations Office (DOE-ID) guidance to comply with DOE Order 5500.3A. The hazards assessment identifies and analyzes the hazards that are significant enough to warrant consideration in a facility`s operational emergency management program. The area surrounding the LC, the buildings and structures at the LC, and the processes that are used at the LC are described in this report. All hazardous materials, both radiological and nonradiological, at the LC were identified and screened against threshold quantities according to DOE Order 5500.3A guidance. Asbestos at the Asbestos Pit was the only hazardous material that exceeded its specified threshold quantity. However, the type of asbestos received and the packaging practices used are believed to limit the potential for an airborne release of asbestos fibers. Therefore, in accordance with DOE Order 5500.3A guidance, no further hazardous material characterization or analysis was required for this hazards assessment.

Structural and functional biological materials: Abalone nacre, sharp materials, and abalone foot adhesion

Science.gov (United States)

Lin, Albert Yu-Min

A three-part study of lessons from nature is presented through the examination of various biological materials, with an emphasis on materials from the mollusk Haliotis rufescens, commonly referred to as the red abalone. The three categories presented are: structural hierarchy, self-assembly, and functionality. Ocean mollusk shells are composed of aragonite/calcite crystals interleaved with layers of a visco-elastic protein, having dense, tailored structures with excellent mechanical properties. The complex nano-laminate structure of this bio-composite material is characterized and related to its mechanical properties. Three levels of structural hierarchy are identified: macroscale mesolayers separating larger regions of tiled aragonite, microscale organization of 0.5 mum by 10 mum aragonite bricks; nanoscale mineral bridges passing through 30 nm layers of organic matrix separating individual aragonite tiles. Composition and growth mechanisms of this nanostructure were observed through close examination of laboratory-grown samples using scanning electron microscopy (SEM), Raman spectroscopy, and transmission electron microscopy (TEM). Glass slides and nacre pucks were implanted onto the growth surface of living abalone and removed periodically to observe trends in nacre deposition. Various deproteinization and demineralization experiments are used to explore the inorganic and organic components of the nacre's structure. The organic component of the shell is characterized by atomic force microscopy (AFM). The functionality of various biological materials is described and investigated. Two specific types of functionality are characterized, the ability of some materials to cut and puncture through sharp designs, and the ability for some materials to be used as attachment devices. Aspects of cutting materials employed by a broad range of animals were characterized and compared. In respect to the attachment mechanisms the foot of the abalone and the tree frog were

Disposal of hazardous wastes

International Nuclear Information System (INIS)

Barnhart, B.J.

1978-01-01

The Fifth Life Sciences Symposium entitled Hazardous Solid Wastes and Their Disposal on October 12 through 14, 1977 was summarized. The topic was the passage of the National Resources Conservation and Recovery Act of 1976 will force some type of action on all hazardous solid wastes. Some major points covered were: the formulation of a definition of a hazardous solid waste, assessment of long-term risk, list of specific materials or general criteria to specify the wastes of concern, Bioethics, sources of hazardous waste, industrial and agricultural wastes, coal wastes, radioactive wastes, and disposal of wastes

Ultrafast electron microscopy in materials science, biology, and chemistry

International Nuclear Information System (INIS)

King, Wayne E.; Campbell, Geoffrey H.; Frank, Alan; Reed, Bryan; Schmerge, John F.; Siwick, Bradley J.; Stuart, Brent C.; Weber, Peter M.

2005-01-01

The use of pump-probe experiments to study complex transient events has been an area of significant interest in materials science, biology, and chemistry. While the emphasis has been on laser pump with laser probe and laser pump with x-ray probe experiments, there is a significant and growing interest in using electrons as probes. Early experiments used electrons for gas-phase diffraction of photostimulated chemical reactions. More recently, scientists are beginning to explore phenomena in the solid state such as phase transformations, twinning, solid-state chemical reactions, radiation damage, and shock propagation. This review focuses on the emerging area of ultrafast electron microscopy (UEM), which comprises ultrafast electron diffraction (UED) and dynamic transmission electron microscopy (DTEM). The topics that are treated include the following: (1) The physics of electrons as an ultrafast probe. This encompasses the propagation dynamics of the electrons (space-charge effect, Child's law, Boersch effect) and extends to relativistic effects. (2) The anatomy of UED and DTEM instruments. This includes discussions of the photoactivated electron gun (also known as photogun or photoelectron gun) at conventional energies (60-200 keV) and extends to MeV beams generated by rf guns. Another critical aspect of the systems is the electron detector. Charge-coupled device cameras and microchannel-plate-based cameras are compared and contrasted. The effect of various physical phenomena on detective quantum efficiency is discussed. (3) Practical aspects of operation. This includes determination of time zero, measurement of pulse-length, and strategies for pulse compression. (4) Current and potential applications in materials science, biology, and chemistry. UEM has the potential to make a significant impact in future science and technology. Understanding of reaction pathways of complex transient phenomena in materials science, biology, and chemistry will provide fundamental

Rapid homogenisation and drying of biological materials

International Nuclear Information System (INIS)

Donev, I.Y.

1977-01-01

In connection with the implementation for detection of trace elements in the pathogenesis of Ischaemic Heart Diseases and for the work of the laboratory a small apparatus for homogenisation and drying biological materials at liquid nitrogen temperature was constructed. For a complete drying 4 to 6 hours are necessary. A laboratory assistant of average qualification can do the work for 13 homogenisates in about 8-9 hours. The capacity of the homogeniser is about 1.5x10 -5 m 3 . Preliminary investigations were carried out for the determination of differences at drying. (T.G.)

Project T100 -- Hazardous Materials Management and Emergency Response Training Center (HAMMER)

International Nuclear Information System (INIS)

Norton, C.E.

1994-01-01

The scope of this Quality Assurance Program Plan (QAPP) is to provide a system of Quality Assurance reviews and verifications on the design and construction of the Hazardous Materials Management and Emergency Response (HAMMER) Training Center, project 95L-EWT-100 at Hanford. The reviews and verifications will be on activities associated with design, procurement, and construction of the HAMMER project which includes, but is not limited to earthwork, placement of concrete, laying of rail, drilling of wells, water and sewer line fabrication and installation, communications systems, fire protection/detection systems, line tie-ins, building and mock-up (prop) construction, electrical, instrumentation, pump and valves and special coatings

User's guide for the KBERT 1.0 code: For the knowledge-based estimation of hazards of radioactive material releases from DOE nuclear facilities

International Nuclear Information System (INIS)

Browitt, D.S.; Washington, K.E.; Powers, D.A.

1995-07-01

The possibility of worker exposure to radioactive materials during accidents at nuclear facilities is a principal concern of the DOE. The KBERT software has been developed at Sandia National Laboratories under DOE support to address this issue by assisting in the estimation of risks posed by accidents at chemical and nuclear facilities. KBERT is an acronym for Knowledge-Based system for Estimating hazards of Radioactive material release Transients. The current prototype version of KBERT focuses on calculation of doses and consequences to in-facility workers due to accidental releases of radioactivity. This report gives detailed instructions on how a user who is familiar with the design, layout and potential hazards of a facility can use KBERT to assess the risks to workers in that facility. KBERT is a tool that allows a user to simulate possible accidents and observe the predicted consequences. Potential applications of KBERT include the evaluation of the efficacy of evacuation practices, worker shielding, personal protection equipment and the containment of hazardous materials

Analysis of occupational accidents with biological material among professionals in pre-hospital services.

Science.gov (United States)

de Oliveira, Adriana Cristina; Paiva, Maria Henriqueta Rocha Siqueira

2013-02-01

To estimate the prevalence of accidents due to biological material exposure, the characteristics and post-accident conduct among professionals of pre-hospital services of the four municipalities of Minas Gerais, Brazil. A cross-sectional study, using a structured questionnaire that was developed to enable the calculation of prevalence, descriptive analysis and analytical analysis using logistic regression. The study included 228 professionals; the prevalence of accidents due to biological material exposure was 29.4%, with 49.2% percutaneous, 10.4% mucousal, 6.0% non-intact skin, and 34.4% intact skin. Among the professionals injured, those that stood out were nursing technicians (41.9%) and drivers (28.3%). Notification of the occurrence of the accident occurred in 29.8% of the cases. Percutaneous exposure was associated with time of work in the organization (OR=2.51, 95% CI: 1.18 to 5.35, paccidents with biological material should be encouraged, along with professional evaluation/monitoring.

Micro-buckling in the nanocomposite structure of biological materials

Science.gov (United States)

Su, Yewang; Ji, Baohua; Hwang, Keh-Chih; Huang, Yonggang

2012-10-01

Nanocomposite structure, consisting of hard mineral and soft protein, is the elementary building block of biological materials, where the mineral crystals are arranged in a staggered manner in protein matrix. This special alignment of mineral is supposed to be crucial to the structural stability of the biological materials under compressive load, but the underlying mechanism is not yet clear. In this study, we performed analytical analysis on the buckling strength of the nanocomposite structure by explicitly considering the staggered alignment of the mineral crystals, as well as the coordination among the minerals during the buckling deformation. Two local buckling modes of the nanostructure were identified, i.e., the symmetric mode and anti-symmetric mode. We showed that the symmetric mode often happens at large aspect ratio and large volume fraction of mineral, while the anti-symmetric happens at small aspect ratio and small volume fraction. In addition, we showed that because of the coordination of minerals with the help of their staggered alignment, the buckling strength of these two modes approached to that of the ideally continuous fiber reinforced composites at large aspect ratio given by Rosen's model, insensitive to the existing "gap"-like flaws between mineral tips. Furthermore, we identified a mechanism of buckling mode transition from local to global buckling with increase of aspect ratio, which was attributed to the biphasic dependence of the buckling strength on the aspect ratio. That is, for small aspect ratio, the local buckling strength is smaller than that of global buckling so that it dominates the buckling behavior of the nanocomposite; for comparatively larger aspect ratio, the local buckling strength is higher than that of global buckling so that the global buckling dominates the buckling behavior. We also found that the hierarchical structure can effectively enhance the buckling strength, particularly, this structural design enables

Scanning probe microscopy in material science and biology

International Nuclear Information System (INIS)

Cricenti, A; Colonna, S; Girasole, M; Gori, P; Ronci, F; Longo, G; Dinarelli, S; Luce, M; Rinaldi, M; Ortenzi, M

2011-01-01

A review of the activity of scanning probe microscopy at our Institute is presented, going from instrumentation to software development of scanning tunnelling microscopy, atomic force microscopy and scanning near-field optical microscopy (SNOM). Some of the most important experiments in material science and biology performed by our group through the years with these SPM techniques will be presented. Finally, infrared applications by coupling a SNOM with a free electron laser will also be presented.

The Widespread Prevalence and Functional Significance of Silk-Like Structural Proteins in Metazoan Biological Materials.

Directory of Open Access Journals (Sweden)

Carmel McDougall

Full Text Available In nature, numerous mechanisms have evolved by which organisms fabricate biological structures with an impressive array of physical characteristics. Some examples of metazoan biological materials include the highly elastic byssal threads by which bivalves attach themselves to rocks, biomineralized structures that form the skeletons of various animals, and spider silks that are renowned for their exceptional strength and elasticity. The remarkable properties of silks, which are perhaps the best studied biological materials, are the result of the highly repetitive, modular, and biased amino acid composition of the proteins that compose them. Interestingly, similar levels of modularity/repetitiveness and similar bias in amino acid compositions have been reported in proteins that are components of structural materials in other organisms, however the exact nature and extent of this similarity, and its functional and evolutionary relevance, is unknown. Here, we investigate this similarity and use sequence features common to silks and other known structural proteins to develop a bioinformatics-based method to identify similar proteins from large-scale transcriptome and whole-genome datasets. We show that a large number of proteins identified using this method have roles in biological material formation throughout the animal kingdom. Despite the similarity in sequence characteristics, most of the silk-like structural proteins (SLSPs identified in this study appear to have evolved independently and are restricted to a particular animal lineage. Although the exact function of many of these SLSPs is unknown, the apparent independent evolution of proteins with similar sequence characteristics in divergent lineages suggests that these features are important for the assembly of biological materials. The identification of these characteristics enable the generation of testable hypotheses regarding the mechanisms by which these proteins assemble and direct the

ATTENDING PROFESSIONALS VICTIMS OF ACCIDENT WITH BIOLOGICAL MATERIAL IN A TROPICAL DISEASES HOSPITAL

OpenAIRE

Lillian Kelly de Oliveira Lopes; Anaclara Ferreira Veiga Tipple; Sirlene Neves Damando; Cássia Silva Miranda; Ivete Vieira Gomes

2006-01-01

ABSTRACT: The occupational risk for the health´s workers is a subject discussed in the last decades. However, the professional accident involving biological material´s records in the health´s units don´t describe the real situation. The purpose of this article is to identify the number of attending of professional accident involving biological material and the source of the leading. The data were obtained by the professional accident´s handbooks in 2003. The hospital had 5768 appointments. Am...

A model of engineering materials inspired by biological tissues

Directory of Open Access Journals (Sweden)

Holeček M.

2009-12-01

Full Text Available The perfect ability of living tissues to control and adapt their mechanical properties to varying external conditions may be an inspiration for designing engineering materials. An interesting example is the smooth muscle tissue since this "material" is able to change its global mechanical properties considerably by a subtle mechanism within individual muscle cells. Multi-scale continuum models may be useful in designing essentially simpler engineering materials having similar properties. As an illustration we present the model of an incompressible material whose microscopic structure is formed by flexible, soft but incompressible balls connected mutually by linear springs. This simple model, however, shows a nontrivial nonlinear behavior caused by the incompressibility of balls and is very sensitive on some microscopic parameters. It may elucidate the way by which "small" changes in biopolymer networks within individual muscular cells may control the stiffness of the biological tissue, which outlines a way of designing similar engineering materials. The 'balls and springs' material presents also prestress-induced stiffening and allows elucidating a contribution of extracellular fluids into the tissue’s viscous properties.

Accidents with potentially hazardous biological material among workers in hospital supporting services.

Science.gov (United States)

Canini, Silvia Rita Marin da Silva; Gir, Elucir; Machado, Alcyone Artiolli

2005-01-01

Descriptive study was carried out to characterize the occupational accidents involving potentially contaminated material among workers of hospital supporting services. The study reviewed records of workers involved in these accidents and attended at a specialized outpatient clinic of a large tertiary care hospital between January 1997 and October 2001. A total of 2814 workers from different professional categories were attended during this period. Of these, 147 (5.2%) belonged to the hospital supporting services and were the victims of 156 accidents, auxiliary cleaning personnel (80.2%), and over a third of the workers had not received any dose of hepatitis B vaccine (35.4%). Most accidents were due to sharp injuries (96.8%) caused by inadequately discarded hollow needles. Chemoprophylaxis for HIV was not indicated in only 23.1% of cases. We conclude that these workers are also exposed to the possibility of acquiring blood-borne pathogens and that periodical education programs are needed.

Radionuclide content and associated radiation hazards of building materials and by-products in Baoji, West China

International Nuclear Information System (INIS)

Lu, X.; Zhang, X.

2008-01-01

Seven types of common building materials and by-products of coal-fired power plants collected from Baoji, West China, were analysed for the natural radioactivity of 226 Ra, 232 Th and 40 K using gamma ray spectrometry with an NaI(Tl) detector. The average activity concentrations vary from 23.0 to 112.2, 20.2 to 147.5 and 113.2 to 890.8 Bq kg -1 for 226 Ra, 232 Th and 40 K, respectively. The measured activity concentrations for these radionuclides were compared with the data reported from other countries and with the worldwide average activity of soil. As a measure of radiation hazard to the people, the radium equivalent activities, total annual effective dose and activity concentration index were estimated. The radium equivalent activities of the studied samples are below the internationally accepted values. The calculated total annual effective dose and the activity concentration index of seven types of common building materials are -1 and 1, respectively. But fly ash and bottom ash exhibit the higher values that exceed and be close to the acceptable values, respectively. This study shows that the measured building materials do not pose any significant source of radiation hazard and are safe for use in the construction of dwellings. Nevertheless, when fly ash and bottom ash are used in dwelling construction, it is important to assess their radiation potential. (authors)

Application of radiochemical separation procedures to environmental and biological materials

Energy Technology Data Exchange (ETDEWEB)

Eakins, J D [UKAEA Atomic Energy Research Establishment, Harwell. Environmental and Medical Sciences Div.

1984-06-15

The measurement of low levels of radionuclides in environmental and biological materials often depends on separation of the nuclide of interest from a bulky matrix containing interfering radioelements. In such case, however sophisticated and elegant the counting technique, the quality of the final data will

Elemental analysis of biological materials. Current problems and techniques with special reference to trace elements

International Nuclear Information System (INIS)

1980-01-01

Selected techniques were reviewed for the assay of trace and minor elements in biological materials. Other relevant information is also presented on the need for such analyses, sampling, sample preparation and analytical quality control. In order to evaluate and compare the applicability of the various analytical techniques on a meaningful and objective basis, the materials chosen for consideration were intended to be typical of a wide range of biological matrics of different elemental compositions, namely Bowen's kale, representing a plant material, and NBS bovine liver, IAEA animal muscle, and blood serum, representing animal tissues. The subject is reviewed under the following headings: on the need for trace element analyses in the life sciences (4 papers); sampling and sample preparation for trace element analysis (2 papers); analytical techniques for trace and minor elements in biological materials (7 papers); analytical quality control (2 papers)

OCCUPATIONAL ACCIDENTS WITH BIOLOGICAL MATERIALS IN CLINICAL ANALYSIS LABORATORY: CAUSES AND CONSEQUENCES

Directory of Open Access Journals (Sweden)

T. M. Azevedo

2014-07-01

Full Text Available Accidents involving biological material can cause diseases to the professional healthcare and also bring psychosocial effects. The aim of this study was to characterize the accidents occurring with biological material with professional of clinical laboratories of Sinop-MT. Data were collected by a questionnaire consisting of sociodemographic and health variables. 21 (87.5% of respondents stated that they never suffered any kind of accident. One of the injured workers reported that there was involvement in your emotional life. It is observed underreporting of occupational accidents by employees affected, making it difficult to increase research on the subject and actions about the problem.

International conference and workshop on modeling and mitigating the consequences of accidental releases of hazardous materials

International Nuclear Information System (INIS)

Anon.

1995-01-01

This conference was held September 26--29, 1995 in New Orleans, Louisiana. The purpose of this conference was to provide a multidisciplinary forum for exchange of state-of-the-art information on the consequences of accidental releases of hazardous materials. Attention is focused on air dispersion of vapors. Individual papers have been processed separately for inclusion in the appropriate data bases

On the possibility of multiple utilization of Bowen's Kale for neutron activation analysis of biological materials

International Nuclear Information System (INIS)

Marinov, V.M.; Lazarova, M.S.; Mihajlov, M.I.; Apostolov, D.

1977-01-01

The results of investigations related to the multiple utilization of Bowen's Kale in developing neutron-activation methods for determining microelements in biological materials carried out in recent years are presented. Bowen's Kale might be used as: (1) experimental material in the development of a method and its verification, i.e. as a test for biological materials; (2) a material where experimental conditions might be optimized; (3) a material for investigating the accuracy, reproducibility and the limit of proof at experimental conditions already defined; (4) a monitor; (5) a multielement volume reference standard for a number of microelements during their simultaneous determination and (6) a standard for verifying the authenticity of the results obtained. In this manner, a reliable criterion for comparison of the potentialities, the accuracy, reproducibility, the limits of proof and the authenticity of the neutron-activation methods of determining microelements in biological materials is introduced. (author)

Hazard analysis in uranium hexafluoride production facility

International Nuclear Information System (INIS)

Marin, Maristhela Passoni de Araujo

1999-01-01

The present work provides a method for preliminary hazard analysis of nuclear fuel cycle facilities. The proposed method identify both chemical and radiological hazards, as well as the consequences associated with accident scenarios. To illustrate the application of the method, a uranium hexafluoride production facility was selected. The main hazards are identified and the potential consequences are quantified. It was found that, although the facility handles radioactive material, the main hazards as associated with releases of toxic chemical substances such as hydrogen fluoride, anhydrous ammonia and nitric acid. It was shown that a contention bung can effectively reduce the consequences of atmospheric release of toxic materials. (author)

Developing emergency exercises for hazardous material transportation: process, documents and templates.

Science.gov (United States)

Crichton, Margaret; Kelly, Terence

2012-01-01

Multi-agency emergency exercises establish and reinforce relationships, and bring people from different areas together to work as a team, realise clear goals, understand roles and responsibilities, and get to know and respect each agency's strengths and weaknesses. However, despite the long-held belief in and respect for exercises in their provision of benefits to the individual and the organisation, there is little evidence of a consistent and clear process for exercise design, especially identifying the documents that may need to be completed to ensure efficient exercise preparation and performance. This paper reports the results of a project undertaken on behalf of the organisations that form the radioactive material transportation mutual-aid agreement, RADSAFE, to develop a standardised process to design emergency exercises. Three stages, from identifying the requirement for an exercise (Stage I), through to obtaining approval for operational orders (Stage II), then conducting a management review as part of the continuous improvement cycle (Stage III), were developed. Although designed for radioactive material transportation events, it is suggested that many of the factors within these three stages can be generalised for the design of exercises in other high-hazard industries.

MAK and BAT values list 2015. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

International Nuclear Information System (INIS)

2015-01-01

The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2015 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

MAK and BAT values list 2014. Maximum permissible concentrations at the place of work and biological tolerance values for working materials

International Nuclear Information System (INIS)

2014-01-01

The book on the MAK (maximum permissible concentrations at the place of work) and BAT (biological tolerance values for working materials) value list 2014 includes the following chapters: (a) Maximum permissible concentrations at the place of work: definition, application and determination of MAT values, list of materials; carcinogenic working materials, sensibilizing working materials, aerosols, limiting the exposition peaks, skin resorption, MAK values during pregnancy, germ cell mutagens, specific working materials; (b) Biological tolerance values for working materials: definition and application of BAT values, list of materials, carcinogenic working materials, biological guide values, biological working material reference values.

Risk assessment of major hazards: Hazardous materials transportation in urban areas

Energy Technology Data Exchange (ETDEWEB)

Hubert, Ph; Pages, P

1988-02-01

There is no doubt that, thanks to the pioneering studies of the late seventies and the early eighties, a methodology has been made available that allows risk management of hazardous transportation in urban areas. This approach can easily be extended to the management of other similar risks (storages and to some extent natural hazards). The methodology is both technically available and affordable. The insertion within the decision making processes deserves still some efforts. It has be seen that the applications are broad and numerous. They range from route selection to emergency preparedness, with some insights into acceptability considerations. One limit to the use of such studies, aiming to an objective assessment of the risk, is the complexity of the decision problems, where many factors are to be considered, the most subtle being the one linked to acceptability. However, as such studies develop, those factors start to be clarified, and decision makers learn how to use risk indices in this context. So at the present time it can be said that risk analyses are a valuable input into the decision making process in most cases. And, as more experience is acquired the uses are broader. As any technical innovation risk assessment modifies the approaches to the questions it is dealing with. It seems impossible now to treat those kinds of risks as was done ten years ago.

Risk assessment of major hazards: Hazardous materials transportation in urban areas

International Nuclear Information System (INIS)

Hubert, Ph.; Pages, P.

1988-02-01

There is no doubt that, thanks to the pioneering studies of the late seventies and the early eighties, a methodology has been made available that allows risk management of hazardous transportation in urban areas. This approach can easily be extended to the management of other similar risks (storages and to some extent natural hazards). The methodology is both technically available and affordable. The insertion within the decision making processes deserves still some efforts. It has be seen that the applications are broad and numerous. They range from route selection to emergency preparedness, with some insights into acceptability considerations. One limit to the use of such studies, aiming to an objective assessment of the risk, is the complexity of the decision problems, where many factors are to be considered, the most subtle being the one linked to acceptability. However, as such studies develop, those factors start to be clarified, and decision makers learn how to use risk indices in this context. So at the present time it can be said that risk analyses are a valuable input into the decision making process in most cases. And, as more experience is acquired the uses are broader. As any technical innovation risk assessment modifies the approaches to the questions it is dealing with. It seems impossible now to treat those kinds of risks as was done ten years ago

75 FR 60017 - Hazardous Materials; Miscellaneous Amendments

Science.gov (United States)

2010-09-29

... prevent shifting or significant relative motion between the packages; that the consolidation bins be... display of the hazard identity (e.g., labels instead of placards) would support a small, more flexible... direction for all or part of their journey. Dynamic forces may shift an unsecured load or cause lading to...

Nuclear, biological and chemical contamination survivability of Army material

International Nuclear Information System (INIS)

Feeney, J.J.

1987-01-01

Army Regulation (AR) 70-71, Nuclear, Biological and Chemical (NBC) Contamination Survivability of Army Material, published during 1984, establishes Army policy and procedures for the development and acquisition of material to ensure its survivablility and sustainability on the NBC-contaminated battlefield. This regulation defines NBC contamination as a term that includes both the individual and collective effects of residual radiological, biological, and chemical contamination. AR 70-71 applies to all mission-essential equipment within the Army. NBC contamination survivability is the capability of a system and its crew to withstand an NBC-contaminated environment, including decontamination, without losing the ability to accomplish the assigned mission. Characteristics of NBC contamination survivability are decontaminability, hardness, and compatability. These characteristics are engineering design criteria which are intended for use only in a developmental setting. To comply with AR 70-71, each mission-essential item must address all three criteria. The Department of Defense (DOD) has published a draft instruction addressing acquisition of NBC contamination survivable systems. This instruction will apply throughout DOD to those programs, systems and subsystems designated by the Secretary of Defense as major systems acquisition programs and to those non-major systems that have potential impact on critical functions

[Accidents with exposure to biological material contaminated with HIV in workers at a third level hospital in Madrid].

Science.gov (United States)

García de Codes Ilario, Aurelia; de Juanes Pardo, José Ramón; Arrazola Martínez, M del Pilar; Jaén Herreros, Felisa; Sanz Gallardo, M Inmaculada; Lago López, Emilia

2004-01-01

Human Immunodeficiency Virus (HIV) is an occupational hazard among healthcare professionals accidentally contaminated with HIV-positive blood. This study is aimed at describing the characteristics of the accidents involving blood of HIV-positive patients recorded over a sixteen-year period at a general hospital. Epidemiological study of the accidents reported in 2001 involving biological material from an HIV-positive source by the healthcare personnel of a general hospital throughout the 1986-2001 period entailing the presence of biological material from HIV-positive serology individuals. Individual, time and place-related variables, in addition to the initial serologies and those throughout the protocolized follow-up were studied for those individuals involved in these accidents. A total 550 accidents entailing an HIV-positive source were reported. The average number of accidents was 34.4/year. The accidental exposure rate for the period under study was 7.5/1000 workers/year. The professional group showing the highest accident rate was the nursing staff (54.4%). Percutaneous injuries were the most frequent (80.2%). The mean exposure rate was 2.6/100 beds/year. The anatomical areas involved to the greatest degree were the fingers (75.6%). A total 53.4% of those injured completed the serological follow-up without having shown any seroconversion. Throughout the sixteen-year period under study, the annual incidence of accidents involving an HIV-positive source increased from the 27 accidents reported in 1986 to the 60 accidents reported in 1990, there having been a downward trend as of that point in time, to the point of 12 accidents having been recorded in 2001.

Final characterization report for the 108-F Biological Laboratory

International Nuclear Information System (INIS)

Harris, R.A.

1996-09-01

This report provides a compilation of characterization data for the 108-F Biological Laboratory collected during the period of May 7, 1996 through August 29, 1996. The 108-F Biology Laboratory is located on the Hanford Site in Richland, Washington. The characterization activities were organized and implemented to evaluate the radiological status of the laboratory and to identify hazardous materials. This report reflects the current conditions and status of the laboratory. Information in this report is intended to be utilized to prepare an accurate cost estimate for building demolition, to aid in planning decontamination and demolition activities, and allow proper disposal of demolition debris

Hydrotreater/Distillation Column Hazard Analysis Report Rev. 2

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-04-15

This project Hazard and Risk Analysis Report contains the results of several hazard analyses and risk assessments. An initial assessment was conducted in 2012, which included a multi-step approach ranging from design reviews to a formal What-If hazard analysis. A second What-If hazard analysis was completed during February 2013 to evaluate the operation of the hydrotreater/distillation column processes to be installed in a process enclosure within the Process Development Laboratory West (PDL-West) facility located on the PNNL campus. The qualitative analysis included participation of project and operations personnel and applicable subject matter experts. The analysis identified potential hazardous scenarios, each based on an initiating event coupled with a postulated upset condition. The unmitigated consequences of each hazardous scenario were generally characterized as a process upset; the exposure of personnel to steam, vapors or hazardous material; a spray or spill of hazardous material; the creation of a flammable atmosphere; or an energetic release from a pressure boundary.

Impacts of Insufficient Instructional Materials on Teaching Biology: Higher Education Systems in Focus

Science.gov (United States)

Edessa, Sutuma

2017-01-01

The purpose of this study was to assess and determine impacts of insufficient instructional materials and ineffective lesson delivery methods on teaching in biology higher education. The participants of this study were 60 trainees who graduated in Bachelor of Sciences from eight public universities in majoring biology. Data for the study was…

Development of the photo catalytic materials for the purification and deodorization of hazardous wastes

International Nuclear Information System (INIS)

Hong, Gye Woon; Park, Ji Yeon; Jung, Choong Hwan; Kim, Weon Ju

1999-12-01

A hazardous material treatment system utilizing photochemical reaction is a new technology which does not produce any secondary pollutants after dissolving treatment because it is activated by solar photo energy. Photo catalysis reaction apparatus using photo catalytic reaction of TiO 2 was fabricated and installed to food waste treatment system for removing bad smell during treatment of food waste. Evolved gas was analysed by gas chromatograph and active carbon fiber sheet and yarn were used as adsorption media for photo catalysis in order to increase the effectiveness of filter system. (author)

Prevention and control of hazards in seafood

DEFF Research Database (Denmark)

Huss, Hans Henrik; Reilly, A.; Embarek, Peter Karim Ben

2000-01-01

-harvest and are difficult or impossible to control by applying presently available preventive measures. In contrast, the hazards related to contamination, recontamination or survival of biological hazards during processing are well-defined and can be controlled by applying Good Manufacturing Practice (GMP), Good Hygiene......Seafood is high on the list of foods transmitting disease. However, the food safety issues are highly focussed and more than 80% of all seafood-borne outbreaks are related to biotoxins (ciguatoxin), scombrotoxin or the consumption of raw molluscan shellfish. The safety hazards in seafood production...

Hazardous materials in Aquatic environments of the Mississippi River basin. Quarterly project status report, 1 January 1994--30 March 1994

Energy Technology Data Exchange (ETDEWEB)

Abdelghani, A.

1994-06-01

Projects associated with this grant for studying hazardous materials in aquatic environments of the Mississippi River Basin are reviewed and goals, progress and research results are discussed. New, one-year initiation projects are described briefly.

Prompt gamma cold neutron activation analysis applied to biological materials

International Nuclear Information System (INIS)

Rossbach, M.; Hiep, N.T.

1992-01-01

Cold neutrons at the external neutron guide laboratory (ELLA) of the KFA Juelich are used to demonstrate their profitable application for multielement characterization of biological materials. The set-up and experimental conditions of the Prompt Gamma Cold Neutron Activation Analysis (PGCNAA) device is described in detail. Results for C, H, N, S, K, B, and Cd using synthetic standards and the 'ratio' technique for calculation are reported for several reference materials and prove the method to be reliable and complementary with respect to the elements being determined by INAA. (orig.)

Fresh biological reference materials. Use in inter laboratory studies and as CRMs

International Nuclear Information System (INIS)

De Boer, J.

1999-01-01

Biological reference materials were prepared and packed in tins and glass jars to be used in inter laboratory studies on chlorobiphenyls and organochlorine pesticides, and trace metals, respectively. The materials were homogenised, sterilised and packed as wet tissue, which is unique for the purpose of inter laboratory studies and offers the advantage of studying the extraction and destruction steps of the analytical methods. In addition to their use in inter laboratory studies, some materials have been prepared or are being prepared as certified reference material for chlorobiphenyl analysis. (author)

Developing strategies to reduce the risk of hazardous materials transportation in iran using the method of fuzzy SWOT analysis

Directory of Open Access Journals (Sweden)

A. S. Kheirkhah

2009-12-01

Full Text Available An increase in hazardous materials transportation in Iran along with the industrial development and increase of resulted deadly accidents necessitate the development and implementation of some strategies to reduce these incidents. SWOT analysis is an efficient method for developing strategies, however, its structural problems, including a lack of prioritizing internal and external factors and inability to consider two sided factors reducing its performance in the situations where the number of internal and external factors affecting the risk of hazardous materials is relatively high and some factors are two sided in nature are presented in the article. Fuzzy SWOT analysis is a method the use of which helps with solving these problems and is the issue of employing an effective methodology. Also, the article compares the resulted strategies of the fuzzy method with the strategies developed following SWOT in order to show the relative supremacy of the new method.

A Decision Support Model Using Life Cycle Cost (LCC) Analysis to Select Cost-Effective Alternatives for Hazardous Materials

Science.gov (United States)

1993-09-01

AF89-071. Washington: GPO, 1989. 159 14. Diaz , SSgt Laura, 648 Med Sq/SGHL. Personal interview. Brooks AFB, San Antonio TX, 14 July 1993. 15. EA...Training Strateav of the Acauisition Management of Hazardous Materials Program. Draft Report. McLean VA, August 1991. 36. Moore, SSgt Alicia . AL/OEVP

Hazard screening application guide

International Nuclear Information System (INIS)

1992-06-01

The basic purpose of hazard screening is to group precesses, facilities, and proposed modifications according to the magnitude of their hazards so as to determine the need for and extent of follow on safety analysis. A hazard is defined as a material, energy source, or operation that has the potential to cause injury or illness in human beings. The purpose of this document is to give guidance and provide standard methods for performing hazard screening. Hazard screening is applied to new and existing facilities and processes as well as to proposed modifications to existing facilities and processes. The hazard screening process evaluates an identified hazards in terms of the effects on people, both on-site and off-site. The process uses bounding analyses with no credit given for mitigation of an accident with the exception of certain containers meeting DOT specifications. The process is restricted to human safety issues only. Environmental effects are addressed by the environmental program. Interfaces with environmental organizations will be established in order to share information

Diffusion theory in biology: a relic of mechanistic materialism.

Science.gov (United States)

Agutter, P S; Malone, P C; Wheatley, D N

2000-01-01

Diffusion theory explains in physical terms how materials move through a medium, e.g. water or a biological fluid. There are strong and widely acknowledged grounds for doubting the applicability of this theory in biology, although it continues to be accepted almost uncritically and taught as a basis of both biology and medicine. Our principal aim is to explore how this situation arose and has been allowed to continue seemingly unchallenged for more than 150 years. The main shortcomings of diffusion theory will be briefly reviewed to show that the entrenchment of this theory in the corpus of biological knowledge needs to be explained, especially as there are equally valid historical grounds for presuming that bulk fluid movement powered by the energy of cell metabolism plays a prominent note in the transport of molecules in the living body. First, the theory's evolution, notably from its origins in connection with the mechanistic materialist philosophy of mid nineteenth century physiology, is discussed. Following this, the entrenchment of the theory in twentieth century biology is analyzed in relation to three situations: the mechanism of oxygen transport between air and mammalian tissues; the structure and function of cell membranes; and the nature of the intermediary metalbolism, with its implicit presumptions about the intracellular organization and the movement of molecules within it. In our final section, we consider several historically based alternatives to diffusion theory, all of which have their precursors in nineteenth and twentieth century philosophy of science.

HMPT: Hazardous Waste Transportation Live 27928, Test 27929

Energy Technology Data Exchange (ETDEWEB)

Simpson, Lewis Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-03-17

HMPT: Hazardous Waste Transportation (Live 27928, suggested one time and associated Test 27929, required initially and every 36 months) addresses the Department of Transportation (DOT) function-specific training requirements of the hazardous materials packagings and transportation (HMPT) Los Alamos National Laboratory (LANL) lab-wide training. This course addresses the requirements of the DOT that are unique to hazardous waste shipments. Appendix B provides the Title 40 Code of Federal Regulations (CFR) reference material needed for this course.

Incidents with hazardous radiation sources; Zwischenfaelle mit gefaehrlichen Strahlenquellen

Energy Technology Data Exchange (ETDEWEB)

Schoenhacker, Stefan [Bundesministerium fuer Inneres, Traiskirchen (Austria). Abt. 1/9 - Zivilschutzschule

2016-07-01

Incidents with hazardous radiation sources can occur in any country, even those without nuclear facilities. Preparedness for such incidents is supposed to fulfill globally agreed minimum standards. Incidents are categorized in incidents with licensed handling of radiation sources as for material testing, transport accidents of hazardous radiation sources, incidents with radionuclide batteries, incidents with satellites containing radioactive inventory, incidents wit not licensed handling of illegally acquired hazardous radiation sources. The emergency planning in Austria includes a differentiation according to the consequences: incidents with release of radioactive materials resulting in restricted contamination, incidents with release of radioactive materials resulting in local contamination, and incidents with the hazard of e@nhanced exposure due to the radiation source.

A new approach to hazardous materials transportation risk analysis: decision modeling to identify critical variables.

Science.gov (United States)

Clark, Renee M; Besterfield-Sacre, Mary E

2009-03-01

We take a novel approach to analyzing hazardous materials transportation risk in this research. Previous studies analyzed this risk from an operations research (OR) or quantitative risk assessment (QRA) perspective by minimizing or calculating risk along a transport route. Further, even though the majority of incidents occur when containers are unloaded, the research has not focused on transportation-related activities, including container loading and unloading. In this work, we developed a decision model of a hazardous materials release during unloading using actual data and an exploratory data modeling approach. Previous studies have had a theoretical perspective in terms of identifying and advancing the key variables related to this risk, and there has not been a focus on probability and statistics-based approaches for doing this. Our decision model empirically identifies the critical variables using an exploratory methodology for a large, highly categorical database involving latent class analysis (LCA), loglinear modeling, and Bayesian networking. Our model identified the most influential variables and countermeasures for two consequences of a hazmat incident, dollar loss and release quantity, and is one of the first models to do this. The most influential variables were found to be related to the failure of the container. In addition to analyzing hazmat risk, our methodology can be used to develop data-driven models for strategic decision making in other domains involving risk.

Developing high-risk scenarios and countermeasure ideas for mitigation of hazardous materials incidents

International Nuclear Information System (INIS)

Russell, E.R. Sr.

1991-01-01

Kansas State University (KSU) conducted a comprehensive study of the development of a set of prioritized, extreme-risk scenarios, the development of a set of feasible, practical and implementable protective systems, and a report to summarize guidelines on the use of these protective systems to mitigate potential, extreme-risk situations that could occur during the transport of hazardous materials (Hazmat) on our highway system. This paper covers the methodology used to compete the first tow objectives with use of a state's panel. The research study was limited to materials (such as LNG, propane, gasoline, etc.) spilled within the highway system. It focused on potential risks which would result in severe, long-term, permanent, irreparable or catastrophic consequences, and existing technology and state-of-the-art knowledge for development of protective systems to mitigate these consequences. The protective systems within the scope of this study were systems constructed or physically incorporated into the highway system or modifications thereto

Thermo-fluidic devices and materials inspired from mass and energy transport phenomena in biological system

Institute of Scientific and Technical Information of China (English)

Jian XIAO; Jing LIU

2009-01-01

Mass and energy transport consists of one of the most significant physiological processes in nature, which guarantees many amazing biological phenomena and activ-ities. Borrowing such idea, many state-of-the-art thermo-fluidic devices and materials such as artificial kidneys, carrier erythrocyte, blood substitutes and so on have been successfully invented. Besides, new emerging technologies are still being developed. This paper is dedicated to present-ing a relatively complete review of the typical devices and materials in clinical use inspired by biological mass and energy transport mechanisms. Particularly, these artificial thermo-fluidic devices and materials will be categorized into organ transplantation, drug delivery, nutrient transport, micro operation, and power supply. Potential approaches for innovating conventional technologies were discussed, corresponding biological phenomena and physical mechan-isms were interpreted, future promising mass-and-energy-transport-based bionic devices were suggested, and prospects along this direction were pointed out. It is expected that many artificial devices based on biological mass and energy transport principle will appear to better improve vari-ous fields related to human life in the near future.

Temperature response of biological materials to pulsed non-ablative CO2 laser irradiation

NARCIS (Netherlands)

Brugmans, M. J.; Kemper, J.; Gijsbers, G. H.; van der Meulen, F. W.; van Gemert, M. J.

1991-01-01

This paper presents surface temperature responses of various tissue phantoms and in vitro and in vivo biological materials in air to non-ablative pulsed CO2 laser irradiation, measured with a thermocamera. We studied cooling off behavior of the materials after a laser pulse, to come to an

Survey of currently available reference materials for use in connection with the determination of trace elements in biological and environmental materials

International Nuclear Information System (INIS)

Muramatsu, Y.; Parr, R.M.

1985-12-01

This report focuses on analytical reference materials which have been developed for use in connection with the determination of toxic and essential trace elements in biomedical and health-related environmental samples. Data are reported on 60 biological and 40 environmental (non-biological) reference materials from 11 suppliers. Certified concentration values (or their equivalents) and non-certified concentration values (or information values) are presented in various tables which are intended to help the user select a reference material that matches as closely as possible (i.e. with respect to matrix type and concentration of the element of interest) the ''real'' samples that are to be analysed. These tables have been generated from a database characterized by the following parameters: total number of reference materials=100; total number of elements recorded=69; total number of concentration values recorded=1771. Also included in the report is information (where available) on the cost of each material, the unit weight or volume supplied, and the minimum weight of material recommended for analysis. (author)

Device for Detection of Explosives, Nuclear and Other Hazardous Materials in Luggage and Cargo Containers

International Nuclear Information System (INIS)

Kuznetsov, Andrey; Evsenin, Alexey; Osetrov, Oleg; Vakhtin, Dmitry; Gorshkov, Igor

2009-01-01

Device for detection of explosives, radioactive and heavily shielded nuclear materials in luggage and cargo containers based on Nanosecond Neutron Analysis/Associated Particles Technique (NNA/APT) is under construction. Detection module consists of a small neutron generator with built-in position-sensitive detector of associated alpha-particles, and several scintillator-based gamma-ray detectors. Explosives and other hazardous chemicals are detected by analyzing secondary high-energy gamma-rays from reactions of fast neutrons with materials inside a container. The same gamma-ray detectors are used to detect unshielded radioactive and nuclear materials. An array of several neutron detectors is used to detect fast neutrons from induced fission of nuclear materials. Coincidence and timing analysis allows one to discriminate between fission neutrons and scattered probing neutrons. Mathematical modeling by MCNP5 and MCNP-PoliMi codes was used to estimate the sensitivity of the device and its optimal configuration. Comparison of the features of three gamma detector types--based on BGO, NaI and LaBr 3 crystals is presented.

Device for Detection of Explosives, Nuclear and Other Hazardous Materials in Luggage and Cargo Containers

Science.gov (United States)

Kuznetsov, Andrey; Evsenin, Alexey; Gorshkov, Igor; Osetrov, Oleg; Vakhtin, Dmitry

2009-12-01

Device for detection of explosives, radioactive and heavily shielded nuclear materials in luggage and cargo containers based on Nanosecond Neutron Analysis/Associated Particles Technique (NNA/APT) is under construction. Detection module consists of a small neutron generator with built-in position-sensitive detector of associated alpha-particles, and several scintillator-based gamma-ray detectors. Explosives and other hazardous chemicals are detected by analyzing secondary high-energy gamma-rays from reactions of fast neutrons with materials inside a container. The same gamma-ray detectors are used to detect unshielded radioactive and nuclear materials. An array of several neutron detectors is used to detect fast neutrons from induced fission of nuclear materials. Coincidence and timing analysis allows one to discriminate between fission neutrons and scattered probing neutrons. Mathematical modeling by MCNP5 and MCNP-PoliMi codes was used to estimate the sensitivity of the device and its optimal configuration. Comparison of the features of three gamma detector types—based on BGO, NaI and LaBr3 crystals is presented.

Neutron-Activation Analysis of Biological Material with High Radiation Levels

Energy Technology Data Exchange (ETDEWEB)

Samsahl, K

1966-09-15

A method has been developed for the chemical separation and subsequent gamma-spectrometric analysis of the alkali metals, the alkaline earths, the rare earths, chromium, hafnium, lanthanum, manganese, phosphorus, scandium and silver in neutron-activated biological material. The separation steps, being fully automatic, are based on a combination of ion-exchange and partition chromatography and require 40 min.

Neutron-Activation Analysis of Biological Material with High Radiation Levels

International Nuclear Information System (INIS)

Samsahl, K.

1966-09-01

A method has been developed for the chemical separation and subsequent gamma-spectrometric analysis of the alkali metals, the alkaline earths, the rare earths, chromium, hafnium, lanthanum, manganese, phosphorus, scandium and silver in neutron-activated biological material. The separation steps, being fully automatic, are based on a combination of ion-exchange and partition chromatography and require 40 min

Preliminary Hazard Classification for the 105-B Reactor

International Nuclear Information System (INIS)

Kerr, N.R.

1997-08-01

This document summarizes the inventories of radioactive and hazardous materials present within the 105-B Reactor and uses the inventory information to determine the preliminary hazard classification for the surveillance and maintenance activities of the facility. The result of this effort was the preliminary hazard classification for the 105-B Building surveillance and maintenance activities. The preliminary hazard classification was determined to be Nuclear Category 3. Additional hazard and accident analysis will be documented in a separate report to define the hazard controls and final hazard classification

Decision support for environmental management of industrial non-hazardous secondary materials: New analytical methods combined with simulation and optimization modeling.

Science.gov (United States)

Little, Keith W; Koralegedara, Nadeesha H; Northeim, Coleen M; Al-Abed, Souhail R

2017-07-01

Non-hazardous solid materials from industrial processes, once regarded as waste and disposed in landfills, offer numerous environmental and economic advantages when put to beneficial uses (BUs). Proper management of these industrial non-hazardous secondary materials (INSM) requires estimates of their probable environmental impacts among disposal as well as BU options. The U.S. Environmental Protection Agency (EPA) has recently approved new analytical methods (EPA Methods 1313-1316) to assess leachability of constituents of potential concern in these materials. These new methods are more realistic for many disposal and BU options than historical methods, such as the toxicity characteristic leaching protocol. Experimental data from these new methods are used to parameterize a chemical fate and transport (F&T) model to simulate long-term environmental releases from flue gas desulfurization gypsum (FGDG) when disposed of in an industrial landfill or beneficially used as an agricultural soil amendment. The F&T model is also coupled with optimization algorithms, the Beneficial Use Decision Support System (BUDSS), under development by EPA to enhance INSM management. Published by Elsevier Ltd.

Health hazards associated with nanomaterials.

Science.gov (United States)

Pattan, Gurulingappa; Kaul, Gautam

2014-07-01

Nanotechnology is a major scientific and economic growth area and presents a variety of hazards for human health and environment. It is widely believed that engineered nanomaterials will be increasingly used in biomedical applications (as therapeutics and as diagnostic tools). However, before these novel materials can be safely applied in a clinical setting, their toxicity needs to be carefully assessed. Nanoscale materials often behave different from the materials with a larger structure, even when the basic material is same. Many mammals get exposed to these nanomaterials, which can reach almost every cell of the mammalian body, causing the cells to respond against nanoparticles (NPs) resulting in cytotoxicity and/or genotoxicity. The important key to understand the toxicity of nanomaterials is that their minute size, smaller than cellular organelles, allows them to penetrate the basic biological structures, disrupting their normal function. There is a wealth of evidence for the noxious and harmful effects of engineered NPs as well as other nanomaterials. The rapid commercialization of nanotechnology field requires thoughtful, attentive environmental, animal and human health safety research and should be an open discussion for broader societal impacts and urgent toxicological oversight action. While 'nanotoxicity' is a relatively new concept to science, this comprehensive review focuses on the nanomaterials exposure through the skin, respiratory tract, and gastrointestinal tract and their mechanism of toxicity and effect on various organs of the body. © The Author(s) 2012.