Study of fine structure of deformed hafnium

International Nuclear Information System (INIS)

Voskresenskaya, L.A.; Petukhova, A.S.; Kovalev, K.S.

1978-01-01

Variations in the hafnium fine structure following the cold plastic deformation have been studied. The fine structure condition has been studied through the harmonic analysis of the profile of the X-ray diffraction line, obtained at the DRON-I installation. Received has been the dependence of the crystal lattice microdistortions value on the deformation extent for hafnium. This dependence is compared with the corresponding one for zirconium. It is found out that at all the deformations the microdistortion distribution is uniform. The microdistortion value grows with the increase in the compression. During the mechanical impact higher microdistortions of the crystal lattice occur in the hafnium rather than in zirconium

Properties of filmogen solutions and films of hafnium compounds

International Nuclear Information System (INIS)

Sviridova, A.I.

1986-01-01

Study on hafnium hydrolizing compound solutions, used for hafnium oxide homogeneous layer formation, is conducted. In particular, electric conductivity, acidity and refractive index were investigated depending on the sal on ether concentration and the storage time. Oxyhafnium nitrate, hafnium chloride in ethanol, dichlorodiethoxyhafnium, hafnium oxychloride were used as initial compounds. Hydrolysis of hafnium compounds in solution occurs partially; further process occurs in the thin layer on the optical element surface; final decomposition is performed under heat treatment. It is ascertained, that alcoholic-aqueous solutions of inorganic salts can be filmogen only at definite acidity, density and viscosity (1.33-2.5 cp.). It is also ascertained that refractive index values and transmission spectral boundary of coatings, produced from alkoxy compound solutions and from chloride salt solutions, are practically the same. Transmittance boundary in ultraviolet region of spectrum of oxide films produced from nitrate and chloride solutions, varies with the heating temperature increase differently

Investigation of ferromagnetism in oxygen deficient hafnium oxide thin films

Energy Technology Data Exchange (ETDEWEB)

Hildebrandt, Erwin; Kurian, Jose; Krockenberger, Yoshiharu; Alff, Lambert [Institut fuer Materialwissenschaft, TU Darmstadt (Germany); Suter, Andreas [PSI, Villingen (Switzerland); Wilhelm, Fabrice; Rogalev, Andrei [ESRF, Grenoble (France)

2008-07-01

Oxygen deficient thin films of hafnium oxide were grown on single crystal r-cut and c-cut sapphire by reactive molecular beam epitaxy. RF-activated oxygen was used for the in situ oxidation of hafnium oxide thin films. Oxidation conditions were varied substantially in order to create oxygen deficiency in hafnium oxide films intentionally. The films were characterized by X-ray and magnetic measurements. X-ray diffraction studies show an increase in lattice parameter with increasing oxygen deficiency. Oxygen deficient hafnium oxide thin films also showed a decreasing bandgap with increase in oxygen deficiency. The magnetisation studies carried out with SQUID did not show any sign of ferromagnetism in the whole oxygen deficiency range. X-ray magnetic circular dichroism measurements also confirmed the absence of ferromagnetism in oxygen deficient hafnium oxide thin films.

Titanium zirconium and hafnium coordination compounds with vanillin thiosemicarbazone

International Nuclear Information System (INIS)

Konunova, Ts.B.; Kudritskaya, S.A.

1987-01-01

Coordination compounds of titanium zirconium and hafnium tetrachlorides with vanillin thiosemicarbazone of MCl 4 x nLig composition, where n=1.5, 4 for titanium and 1, 2, 4 for zirconium and hafnium, are synthesized. Molar conductivity of ethanol solutions is measured; IR spectroscopic and thermochemical investigation are carried out. The supposition about ligand coordination via sulfur and azomethine nitrogen atoms is made. In all cases hafnium forms stable compounds than zirconium

Hafnium - material for chemical apparatus engineering

International Nuclear Information System (INIS)

Jennert, D.

1981-01-01

This work describes - on the background of available literature - the properties of hafnium in technical quality (DIN-material No. 2.6400) as material for chemical apparatus engineering. The occurence, refining, physical and chemical properties will be described as well as the material behavior. In conclusion, it has been found that there is, at present, sufficient information for the engineering of hafnium which has to be completed by additional investigations for special applications. (orig.) [de

Internal Dosimetry for Inhalation of Hafnium Tritide Aerosols

Energy Technology Data Exchange (ETDEWEB)

Inkret, W.C.T.; Schillaci, M.E.; Boyce, M.K.; Cheng, Y.S.; Efurd, D.W.; Little, T.T.; Miller, G.; Musgrave, J.A.; Wermer, J.R

2001-07-01

Metal tritides with low dissolution rates may have residence times in the lungs which are considerably longer than the biological half-time normally associated with tritium in body water, resulting in long-term irradiation of the lungs by low energy {beta} particles and bremsstrahlung X rays. Samples of hafnium tritide were placed in a lung simulant fluid to determine approximate lung dissolution rates. Hafnium hydride samples were analysed for particle size distribution with a scanning electron microscope. Lung simulant data indicated a biological dissolution half-time for hafnium tritide on the order of 10{sup 5}d. Hafnium hydride particle sizes ranged between 2 and 10 {mu}m, corresponding to activity median aerodynamic diameters of 5 to 25 {mu}m. Review of in vitro dissolution data, development of a biokinetic model, and determination of secondary limits for 1 {mu}m AMAD particles are presented and discussed. (author)

Titanium(IV), zirconium, hafnium and thorium

International Nuclear Information System (INIS)

Brown, Paul L.; Ekberg, Christian

2016-01-01

Titanium can exist in solution in a number of oxidation states. The titanium(IV) exists in acidic solutions as the oxo-cation, TiO 2+ , rather than Ti 4+ . Zirconium is used in the ceramics industry and in nuclear industry as a cladding material in reactors where its reactivity towards hydrolysis reactions and precipitation of oxides may result in degradation of the cladding. In nature, hafnium is found together with zirconium and as a consequence of the contraction in ionic radii that occurs due to the 4f -electron shell, the ionic radius of hafnium is almost identical to that of zirconium. All isotopes of thorium are radioactive and, as a consequence of it being fertile, thorium is important in the nuclear fuel cycle. The polymeric hydrolysis species that have been reported for thorium are somewhat different to those identified for zirconium and hafnium, although thorium does form the Th 4 (OH) 8 8+ species.

Ferroelectricity in undoped hafnium oxide

International Nuclear Information System (INIS)

Polakowski, Patrick; Müller, Johannes

2015-01-01

We report the observation of ferroelectric characteristics in undoped hafnium oxide thin films in a thickness range of 4–20 nm. The undoped films were fabricated using atomic layer deposition (ALD) and embedded into titanium nitride based metal-insulator-metal (MIM) capacitors for electrical evaluation. Structural as well as electrical evidence for the appearance of a ferroelectric phase in pure hafnium oxide was collected with respect to film thickness and thermal budget applied during titanium nitride electrode formation. Using grazing incidence X-Ray diffraction (GIXRD) analysis, we observed an enhanced suppression of the monoclinic phase fraction in favor of an orthorhombic, potentially, ferroelectric phase with decreasing thickness/grain size and for a titanium nitride electrode formation below crystallization temperature. The electrical presence of ferroelectricity was confirmed using polarization measurements. A remanent polarization P r of up to 10 μC cm −2 as well as a read/write endurance of 1.6 × 10 5 cycles was measured for the pure oxide. The experimental results reported here strongly support the intrinsic nature of the ferroelectric phase in hafnium oxide and expand its applicability beyond the doped systems

Hafnium-Based Contrast Agents for X-ray Computed Tomography.

Science.gov (United States)

Berger, Markus; Bauser, Marcus; Frenzel, Thomas; Hilger, Christoph Stephan; Jost, Gregor; Lauria, Silvia; Morgenstern, Bernd; Neis, Christian; Pietsch, Hubertus; Sülzle, Detlev; Hegetschweiler, Kaspar

2017-05-15

Heavy-metal-based contrast agents (CAs) offer enhanced X-ray absorption for X-ray computed tomography (CT) compared to the currently used iodinated CAs. We report the discovery of new lanthanide and hafnium azainositol complexes and their optimization with respect to high water solubility and stability. Our efforts culminated in the synthesis of BAY-576, an uncharged hafnium complex with 3:2 stoichiometry and broken complex symmetry. The superior properties of this asymmetrically substituted hafnium CA were demonstrated by a CT angiography study in rabbits that revealed excellent signal contrast enhancement.

40 CFR 471.90 - Applicability; description of the zirconium-hafnium forming subcategory.

Science.gov (United States)

2010-07-01

... zirconium-hafnium forming subcategory. 471.90 Section 471.90 Protection of Environment ENVIRONMENTAL... POINT SOURCE CATEGORY Zirconium-Hafnium Forming Subcategory § 471.90 Applicability; description of the zirconium-hafnium forming subcategory. This subpart applies to discharges of pollutants to waters of the...

Calorimetric measurements on hafnium titanate

International Nuclear Information System (INIS)

Kandan, R.; Prabhakara Reddy, B.; Panneerselvam, G.; Nagarajan, K.

2012-01-01

Owing to its desirable nuclear and mechanical properties such as good absorption cross-section for thermal neutrons (105 barns), hafnium titanate (HfTiO 4 ) finds application as control rods for nuclear reactors. An accurate knowledge of the thermo physical properties of this material is necessary for design of control rod and for modeling its performance. Heat capacity is an important thermodynamic property that determines the temperature dependent variation of all other thermodynamic properties. Hence enthalpy increments of hafnium titanate (HfTiO 4 ) were measured in the temperature range 803-1663 K by employing the method of inverse drop calorimetry using high temperature differential calorimeter

Preparation of complexes of zirconium and hafnium tetrachlorides with phosphorus oxychloride

International Nuclear Information System (INIS)

Snyder, T.S.; Stoltz, R.A.

1989-01-01

This patent describes an improvement in a method for separating hafnium chloride from zirconium chloride using a distillation column, with a hafnium chloride enriched vapor stream taken from the top of the column and a zirconium enriched chloride stream taken from the bottom of the column. The improvement comprising: purifying the zirconium-hafnium chloride in a molten salt purification vessel prior to or after introduction into the distillation column to substantially eliminate iron chloride from the zirconium-hafnium chloride by at least periodically removing iron chloride from the molten salt purification vessel by electrochemically plating iron onto an electrode in the molten salt purification vessel. The molten salt in the molten salt purification vessel consisting essentially of a mixture of chlorides selected from the group consisting of alkali metals, alkaline earth metals, zirconium, hafnium, aluminum, manganese, and zinc

Method of purifying zirconium tetrachloride and hafnium tetrachloride in a vapor stream

International Nuclear Information System (INIS)

Snyder, T.S.; Stolz, R.A.

1992-01-01

This patent describes a method of purifying zirconium tetrachloride and hafnium tetrachloride in a vapor stream from a sand chlorinator in which the silicon and metals present in sand fed to the chlorinator are converted to chlorides at temperatures over about 800 degrees C. It comprises cooling a vapor stream from a sand chlorinator, the vapor stream containing principally silicon tetrachloride, zirconium tetrachloride, and hafnium tetrachloride contaminated with ferric chloride, to a temperature of from about 335 degrees C to about 600 degrees C; flowing the vapor stream through a gaseous diffusion separative barrier to produce a silicon tetrachloride-containing vapor stream concentrated in zirconium tetrachloride and hafnium tetrachloride and a silicon tetrachloride-containing vapor stream depleted in zirconium tetrachloride and hafnium tetrachloride; adsorbing the ferric chloride in the separative barrier; and recovering the silicon tetrachloride stream concentrated in zirconium tetrachloride and hafnium tetrachloride separately from the silicon tetrachloride stream depleted in zirconium tetrachloride and hafnium tetrachloride

Spectrofluorimetric determination of hafnium and zirconium with 3,7-dihydroxyflavone

Energy Technology Data Exchange (ETDEWEB)

Ito, Takushi; Suzuki, Osamu; Seuzuki, Tetsuo; Murata, Akira

1986-04-01

The absorptive and fluorescent characteristics of the hafnium and zirconium complexes of 3-hydroxyflavone and its 12 hydroxy and methoxy derivatives have been studied. The fluorescence of the 1:1 hafnium - 3,7-dihydroxyflavone complex (lambdasub(ex.)397 nm,lambdasub(em.) 465 nm) in 3 M hydrochloric acid has been used to determine 2-40 ng ml/sup -1/ of hafnium. The fluorescence of the 1:1 zirconium - 3,7-dihydroxyflavone complex (lambdasub(ex.) 395 nm, lambda sub(em.) 465 nm) at pH 2.0 in 0.02 M sulphate solution has been used to determine 2-40 ng ml/sup -1/ of zirconium. These methods are very sensitive and can be used for the simultaneous determination of hafnium and zirconium with an error of about 5%.

Molten salt extractive distillation process for zirconium-hafnium separation

International Nuclear Information System (INIS)

McLaughlin, D.F.; Stoltz, R.A.

1989-01-01

This patent describes an improvement in a process for zirconium-hafnium separation. It utilizes an extractive distillation column with a mixture of zirconium and hafnium tetrachlorides introduced into a distillation column having a top and bottom with hafnium enriched overheads taken from the top of the column and a molten salt solvent circulated through the column to provide a liquid phase, and with molten salt solvent containing zirconium chloride being taken from the bottom of the distillation column. The improvements comprising: utilizing a molten salt solvent consisting principally of lithium chloride and at least one of sodium, potassium, magnesium and calcium chlorides; stripping of the zirconium chloride taken from the bottom of the distillation column by electrochemically reducing zirconium from the molten salt solvent; and utilizing a pressurized reflux condenser on the top of the column to add the hafnium chloride enriched overheads to the molten salt solvent previously stripped of zirconium chloride

40 CFR 421.330 - Applicability: Description of the primary zirconium and hafnium subcategory.

Science.gov (United States)

2010-07-01

... primary zirconium and hafnium subcategory. 421.330 Section 421.330 Protection of Environment ENVIRONMENTAL... CATEGORY Primary Zirconium and Hafnium Subcategory § 421.330 Applicability: Description of the primary zirconium and hafnium subcategory. The provisions of this subpart are applicable to discharges resulting...

Design and fabrication of hafnium tube to control the power of the irradiation test fuel in HANARO

Energy Technology Data Exchange (ETDEWEB)

Kim, D. H.; Lee, C. B.; Kim, Y. M.; Yang, Y. S.; Jung, Y. H

2003-05-01

For the irradiation test at HANARO, non-instrumentation capsule was manufactured and hafnium tube was used to control LHGR of HANARO. Hafnium tube can control the irradiation condition of HANARO similar to that of commercial reactor. Hafnium tube thickness was determined by the LHGR calculated at OR-4 irradiation hole to be installed the non-instrumented capsule. To fabricate the hafnium tube with hafnium plate, the fabrication method was determined by using the hafnium mechanical properties. And the tensile strength of hafnium was confirmed by tensile test. This report is confirmed the LHGR control at the OR-4 and the Hafnium fabrication for in used which the AFPCAP non-instrumented irradiation capsule.

Use of X-ray fluorescence analysis for the determination of hafnium in zircalloys

International Nuclear Information System (INIS)

Sato, I.M.; Salvador, V.L.R.; Lordello, A.R.

1985-01-01

The determination of hafnium at trace levels (ppm) in the presence of zirconium by X-ray fluorescence technique is presented. The samples were prepared in the form of double-layer pellets, with boric acid as the binding material. The most sensitive first order line of hafnium HfLα (0.157 nm), which is used analyticaly, has approximately 67% overlapping with second order line of zirconium ZrKα 1 , (0.079 nm). As the excitation potencial of zirconium is larger than hafnium, the best condition was selected, so that the interference of zirconium intensity would not be significant in hafnium analytical line. The method allowed the determination of hafnium above 5.0 ppm (LLd = 1.5 ppm) with an accuracy of less than 10%. (Author) [pt

Use of hafnium in control bars of nuclear reactors

International Nuclear Information System (INIS)

Ramirez S, J.R.; Alonso V, G.

2003-01-01

Recently the use of hafnium as neutron absorber material in nuclear reactors has been reason of investigation by virtue of that this material has nuclear properties as to the neutrons absorption and structural that can prolong the useful life of the control mechanisms of the nuclear reactors. In this work some of those more significant hafnium properties are presented like nuclear material. Also there are presented calculations carried out with the HELIOS code for fuel cells of uranium oxide and of uranium and plutonium mixed oxides under controlled conditions with conventional bars of boron carbide and also with similar bars to which are substituted the absorbent material by metallic hafnium, the results are presented in this work. (Author)

The corrosion behavior of hafnium in high-temperature-water environments

Energy Technology Data Exchange (ETDEWEB)

Rishel, D.M.; Smee, J.D.; Kammenzind, B.F.

1999-10-01

The high-temperature-water corrosion performance of hafnium is evaluated. Corrosion kinetic data are used to develop correlations that are a function of time and temperature. The evaluation is based on corrosion tests conducted in out-of-pile autoclaves and in out-of-flux locations of the Advanced Test Reactor (ATR) at temperatures ranging from 288 to 360 C. Similar to the corrosion behavior of unalloyed zirconium, the high-temperature-water corrosion response of hafnium exhibits three corrosion regimes: pretransition, posttransition, and spalling. In the pretransition regime, cubic corrosion kinetics are exhibited, whereas in the posttransition regime, linear corrosion kinetics are exhibited. Because of the scatter in the spalling regime data, it is not reasonable to use a best fit of the data to describe spalling regime corrosion. Data also show that neutron irradiation does not alter the corrosion performance of hafnium. Finally, the data illustrate that the corrosion rate of hafnium is significantly less than that of Zircaloy-2 and Zircaloy-4.

Corrosion potentials of hafnium in molten alkaline-earth metal chlorides

International Nuclear Information System (INIS)

Kovalik, O.Yu.; Tkhaj, V.D.

2000-01-01

Corrosion potentials of hafnium in molten calcium, strontium and barium chlorides are measured and their temperature dependences are determined. It is stated that the corrosion potential of hafnium becomes more electropositive with an increase of the environment temperature. If the temperature is the same the potential shifts to the interval of more electronegative values in the row of CaCl 2 , SrCl 2 , BaCl 2 which corresponds to a lesser corrosion rate in environments positioned from left to right. the comparison of hafnium corrosion potentials with previously measured values for titanium and zirconium shows that a metal activity decrease results in a more electronegative corrosion potential [ru

Electronic structure of pentacene on hafnium studied by ultraviolet photoelectron spectroscopy

International Nuclear Information System (INIS)

Kang, Seong Jun; Yi, Yeon Jin; Kim, Chung Yi; Whang, Chung Nam

2005-01-01

The electronic structure of pentacene on hafnium, which is a low work function metal, was analyzed by using ultraviolet photoelectron spectroscopy. The energy level alignment was studied by using the onset of the highest occupied molecular orbital level and the shift of the vacuum level of the pentacene layer, which was deposited on a clean hafnium surface in a stepwise manner. The measured onset of the highest occupied molecular orbital energy level was 1.52 eV from the Fermi level of hafnium. The vacuum level was shifted 0.28 eV toward higher binding energy with additional pentacene layers, which means an interfacial dipole exists at the interface between pentacene and hafnium. We confirm that a small electron injection barrier can be achieved by inserting a low work function metal in a pentacene thin-film transistor.

Synthesis of Hafnium-Based Ceramic Materials for Ultra-High Temperature Aerospace Applications

Science.gov (United States)

Johnson, Sylvia; Feldman, Jay

2004-01-01

This project involved the synthesis of hafnium (Hf)-based ceramic powders and Hf-based precursor solutions that were suitable for preparation of Hf-based ceramics. The Hf-based ceramic materials of interest in this project were hafnium carbide (with nominal composition HE) and hafnium dioxide (HfO2). The materials were prepared at Georgia Institute of Technology and then supplied to research collaborators Dr. Sylvia Johnson and Dr. Jay Feldman) at NASA Ames Research Center.

Application of hafnium hydride control rod to large sodium cooled fast breeder reactor

Energy Technology Data Exchange (ETDEWEB)

Ikeda, Kazumi, E-mail: kazumi_ikeda@mfbr.mhi.co.jp [Mitsubishi FBR Systems, Inc., 34-17, Jingumae 2-Chome, Shibuya-ku, Tokyo 150-0001 (Japan); Moriwaki, Hiroyuki, E-mail: hiroyuki_moriwaki@mfbr.mhi.co.jp [Mitsubishi FBR Systems, Inc., 34-17, Jingumae 2-Chome, Shibuya-ku, Tokyo 150-0001 (Japan); Ohkubo, Yoshiyuki, E-mail: yoshiyuki_okubo@mfbr.mhi.co.jp [Mitsubishi FBR Systems, Inc., 34-17, Jingumae 2-Chome, Shibuya-ku, Tokyo 150-0001 (Japan); Iwasaki, Tomohiko, E-mail: tomohiko.iwasaki@qse.tohoku.ac.jp [Department of Quantum Science and Energy Engineering, Tohoku University, Aoba, Aramaki, Aoba-ku, Sendai-shi, Miyagi-ken 980-8579 (Japan); Konashi, Kenji, E-mail: konashi@imr.tohoku.ac.jp [Institute for Materials Research, Tohoku University, Narita-cho, Oarai-machi, Higashi-Ibaraki-gun, Ibaraki-ken 311-1313 (Japan)

2014-10-15

Highlights: • Application of hafnium hydride control rod to large sodium cooled fast breeder reactor. • This paper treats application of an innovative hafnium hydride control rod to a large sodium cooled fast breeder reactor. • Hydrogen absorption triples the reactivity worth by neutron spectrum shift at H/Hf ratio of 1.3. • Lifetime of the control rod quadruples because produced daughters of hafnium isotopes are absorbers. • Nuclear and thermal hydraulic characteristics of the reactor are as good as or better than B-10 enriched boron carbide. - Abstract: This study treats the feasibility of long-lived hafnium hydride control rod in a large sodium-cooled fast breeder reactor by nuclear and thermal analyses. According to the nuclear calculations, it is found that hydrogen absorption of hafnium triples the reactivity by the neutron spectrum shift at the H/Hf ratio of 1.3, and a hafnium transmutation mechanism that produced daughters are absorbers quadruples the lifetime due to a low incineration rate of absorbing nuclides under irradiation. That is to say, the control rod can function well for a long time because an irradiation of 2400 EFPD reduces the reactivity by only 4%. The calculation also reveals that the hafnium hydride control rod can apply to the reactor in that nuclear and thermal characteristics become as good as or better than 80% B-10 enriched boron carbide. For example, the maximum linear heat rate becomes 3% lower. Owing to the better power distribution, the required flow rate decreases approximately by 1%. Consequently, it is concluded on desk analyses that the long lived hafnium hydride control rod is feasible in the large sodium-cooled fast breeder reactor.

X-Ray Photoemission Study of the Oxidation of Hafnium

International Nuclear Information System (INIS)

Chourasia, R.; Hickman, J.L.; Miller, R.L.; Nixon, G.A.; Seabolt, M.A.

2011-01-01

About 20 angstrom of hafnium were deposited on silicon substrates using the electron beam evaporation technique. Two types of samples were investigated. In one type, the substrate was kept at the ambient temperature. After the deposition, the substrate temperature was increased to 100, 200, and 300 degree C. In the other type, the substrate temperature was held fixed at some value during the deposition. For this type, the substrate temperatures used were 100, 200, 300, 400, 500, 550, and 600 degree C. The samples were characterized in situ by the technique of X-ray photoelectron spectroscopy. No trace of elemental hafnium is observed in the deposited overlayer. Also, there is no evidence of any chemical reactivity between the overlayer and the silicon substrate over the temperature range used. The hafnium overlayer shows a mixture of the dioxide and the suboxide. The ratio of the suboxide to dioxide is observed to be more in the first type of samples. The spectral data indicate that hafnium has a strong affinity for oxygen. The overlayer gets completely oxidized to form HfO 2 at substrate temperature around 300 degree C for the first type of samples and at substrate temperature greater than 550 degree C for the second type

X-Ray Photoemission Study of the Oxidation of Hafnium

Directory of Open Access Journals (Sweden)

A. R. Chourasia

2009-01-01

Full Text Available About 20 Å of hafnium were deposited on silicon substrates using the electron beam evaporation technique. Two types of samples were investigated. In one type, the substrate was kept at the ambient temperature. After the deposition, the substrate temperature was increased to 100, 200, and 300∘C. In the other type, the substrate temperature was held fixed at some value during the deposition. For this type, the substrate temperatures used were 100, 200, 300, 400, 500, 550, and 600∘C. The samples were characterized in situ by the technique of X-ray photoelectron spectroscopy. No trace of elemental hafnium is observed in the deposited overlayer. Also, there is no evidence of any chemical reactivity between the overlayer and the silicon substrate over the temperature range used. The hafnium overlayer shows a mixture of the dioxide and the suboxide. The ratio of the suboxide to dioxide is observed to be more in the first type of samples. The spectral data indicate that hafnium has a strong affinity for oxygen. The overlayer gets completely oxidized to form HfO2 at substrate temperature around 300∘C for the first type of samples and at substrate temperature greater than 550∘C for the second type.

High temperature diffusion of hafnium in tungsten and a tungsten-hafnium carbide alloy

International Nuclear Information System (INIS)

Ozaki, Y.; Zee, R.H.

1994-01-01

Refractory metals and ceramics are used extensively in energy systems due to their high temperature properties. This is particularly important in direct conversion systems where thermal to electric conversion efficiency is a direct function of temperature. Tungsten, which has the highest melting temperature among elemental metals, does not possess sufficient creep resistance at temperature above 1,600 K. Different dispersion strengthened tungsten alloys have been developed to extend the usefulness of tungsten to higher temperatures. One of these alloys, tungsten with 0.4 mole percent of finely dispersed HfC particles (W-HfC), has the optimum properties for high temperature applications. Hafnium carbide is used as the strengthening agent due to its high chemical stability and its compatibility with tungsten. The presence of HfC particles retards the rate of grain growth as well as restricting dislocation motion. Both of which are beneficial for creep resistance. The long term behavior of this alloy depends largely on the evolution of its microstructure which is governed by the diffusion of its constituents. Data on the diffusion of carbon in tungsten and tungsten self-diffusion are available, but no direct measurements have been made on the diffusion of hafnium in tungsten. The only diffusion data available are estimated from a coarsening study and these data are highly unreliable. In this study, the diffusion behavior of hafnium in pure tungsten and in a W-HfC alloy was directly measured by means of Secondary Ion Mass Spectroscopy (SIMS). The selection of the W-HfC alloy is due to its importance in high temperature engineering applications, and its higher recrystallization temperature. The presence of HfC particles in tungsten restricts grain growth resulting in better high temperature creep resistance. The higher recrystallization temperature allows measurements to be made over a wider range of temperatures at a relatively constant grain size

Elaboration and characterisation of yttrium oxide and hafnium oxide powders by the sol-gel process

International Nuclear Information System (INIS)

Hours, T.

1988-01-01

The two classical sol-gel processes, colloidal and polymeric are studied for the preparation of yttrium oxide and hafnium oxide high performance powders. In the colloidal process, controlled and reproducible conditions for the preparation of yttrium oxide and hafnium oxide sols from salts or alkoxides are developed and the hydrothermal synthesis monodisperse hafnium oxide colloids is studied. The polymeric process is studied with hafnium ethyl-hexylate, hydrolysis kinetics for controlled preparation of sols and gels is investigated. Each step of preparation is detailed and powders obtained are characterized [fr

Modelling of Zirconium and Hafnium separation using continuous annular chromatography

International Nuclear Information System (INIS)

Moch-Setyadji; Endang Susiantini

2014-01-01

Nuclear degrees of zirconium in the form of a metal alloy is the main material for fuel cladding of NPP. Zirconium is also used as sheathing UO 2 kernel in the form of ZrC as a substitute of SiC in the fuel elements of High Temperature Reactor (HTR). Difficulty separating hafnium from zirconium because it has a lot of similarities in the chemical properties of Zr and Hf. Annular chromatography is a device that can be used for separating of zirconium and hafnium to obtain zirconium nuclear grade. Therefore, it is necessary to construct the mathematical modelling that can describe the separation of zirconium and hafnium in the annular chromatography containing anion resin dowex-1X8. The aim of research is to perform separation simulation by using the equilibrium model and mass transfer coefficient resulted from research. Zr and Hf feed used in this research were 26 and 1 g/l, respectively. Height of resin (L), angular velocity (ω) and the superficial flow rate (uz) was varied to determine the effect of each parameter on the separation of Zr and Hf. By using Kd and Dv values resulted previous research. Simulation results showed that zirconium and hafnium can be separated using a continuous annular chromatography with high resin (long bed) 50 cm, superficial flow rate of 0.001 cm/s, the rotation speed of 0.006 rad/min and 20 cm diameter annular. In these conditions the results obtained zirconium concentration of 10,303.226 g/m 3 and hafnium concentration of 12.324 g/m 3 (ppm). (author)

Joint titrimetric determination of zirconium and hafnium

International Nuclear Information System (INIS)

Vazquez, Cristina; Botbol, Moises; Bianco de Salas, G.N.; Cornell de Casas, M.I.

1980-01-01

A method for the joint titrimetric determination of zirconium and hafnium, which are elements of similar chemical behaviour, is described. The disodic salt of the ethylendiaminetetracetic acid (EDTA) is used for titration, while xilenol orange serves as final point indicator. Prior to titration it is important to evaporate with sulfuric acid, the solution resulting from the zirconium depolymerization process, to adjust the acidity and to eliminate any interferences. The method, that allows the quick and precise determination of zirconium and hafnium in quantities comprised between 0.01 and mg, was applied to the analysis of raw materials and of intermediate and final products in the fabrication of zirconium sponge and zircaloy. (M.E.L.) [es

Compositional characterization of hafnium alloy used as control rod material in nuclear reactor

International Nuclear Information System (INIS)

Sharma, P.K.; Bassan, M.K.T.; Avhad, D.K.; Singhal, R.K.

2014-01-01

Hafnium (Hf) is a heavy, steel-gray metal in the reactive metals group that is very closely related to zirconium (Zr) and forms a continuous solid-solution at all concentrations of zirconium and hafnium. Hafnium occurs naturally with zirconium at a ratio of approximately 1:50 and is produced exclusively as a co-product of nuclear-grade zirconium. It is used in a variety of applications where few substitutes are available. Thus with its relatively high thermal neutron absorption cross-section, hafnium's biggest application is as control rod material in nuclear reactors. During this work, major (Zirconium (Zr), Cobalt (Co) and Molybdenum (Mo)) and trace ((Iron (Fe), Nickel (Ni) and Titanium (Ti)) elements were measured in the bulk matrices of Hf. These materials are also associated with other impurities such as O, N, H etc.

Bond formation in hafnium atom implantation into SiC induced by high-energy electron irradiation

International Nuclear Information System (INIS)

Yasuda, H.; Mori, H.; Sakata, T.; Naka, M.; Fujita, H.

1992-01-01

Bilayer films of Hf (target atoms)/α-SiC (substrate) were irradiated with 2 MeV electrons in an ultra-high voltage electron microscope (UHVEM), with the electron beam incident on the hafnium layer. As a result of the irradiation, hafnium atoms were implanted into the SiC substrate. Changes in the microstructure and valence electronic states associated with the implantation were studied by a combination of UHVEM and Auger valence electron spectroscopy. The implantation process is summarized as follows. (1) Irradiation with 2 MeV electrons first induces a crystalline-to-amorphous transition in α-SiC. (2) Hafnium atoms which have been knocked-off from the hafnium layer by collision with the 2 MeV electrons are implanted into the resultant amorphous SiC. (3) The implanted hafnium atoms make preferential bonding to carbon atoms. (4) With continued irradiation, the hafnium atoms repeat the displacement along the beam direction and the subsequent bonding with the dangling hybrids of carbon and silicon. The repetition of the displacement and subsequent bonding lead to the deep implantation of hafnium atoms into the SiC substrate. It is concluded that implantation successfully occurs when the bond strength between a constituent atom of a substrate and an injected atom is stronger than that between constituent atoms of a substrate. (Author)

Hafnium Resonance Parameter Analysis Using Neutron Capture and Transmission Experiments

International Nuclear Information System (INIS)

MJ Trbovich; DP Barry; RE Slovacck; Y Danon; RC Block; JA Burke; NJ Drindak; G Leinweber; RV Ballad

2004-01-01

The focus of this work is to determine resonance parameters for stable hafnium isotopes in the 0.005-200 eV region, with special emphasis on the overlapping 176 Hf and 178 Hf resonances near 8 eV. The large neutron cross section of hafnium, combined with its corrosion resistance and excellent mechanical properties, make it a useful material for controlling nuclear reactions. Experiments measuring neutron capture and transmission were performed at the Rensselaer Polytechnic Institute (RPI) electron linear accelerator (LINAC) using the time of flight method. 6 Li glass scintillation detectors were used for transmission experiments at flight path lengths of 15 and 25 m. Capture experiments were done using a sixteen section NaI(Tl) multiplicity detector at a flight path length of 25 m. These experiments utilized various thicknesses of metallic and isotopically-enriched liquid samples. The liquid samples were designed to provide information on the 176 Hf and 178 Hf contributions to the 8 eV doublet without saturation. Data analysis was done using the R-matrix Bayesian code SAMMY version M6 beta. SAMMY is able to account for experimental resolution effects for each of the experimental setups at the RPI LINAC, and also can correct for multiple scattering effects in neutron capture yield data. The combined capture and transmission data analysis yielded resonance parameters for all hafnium isotopes from 0.005-200 eV. Resonance integrals were calculated along with errors for each hafnium isotope using the NJOY [1] and INTER [2] codes. The isotopic resonance integrals calculated were significantly different than previously published values; however the calculated elemental hafnium resonance integral changed very little

Zirconium and hafnium in the southeastern Atlantic States

Science.gov (United States)

Mertie, J.B.

1958-01-01

The principal source of zirconium and hafnium is zircon, though a minor source is baddeleyite, mined only in Brazil. Zircon is an accessory mineral in igneous, metamorphic, and sedimentary rocks, but rarely occurs in hardrock in minable quantities. The principal sources of zircon are therefore alluvial deposits, which are mined in many countries of five continents. The principal commercial deposits in the United States are in Florida, though others exist elsewhere in the southeastern Coastal Plain. The evidence indicates that conditions for the accumulation of workable deposits of heavy minerals were more favorable during the interglacial stages of the Pleistocene epoch than during Recent time. Therefore detrital ores of large volume and high tenor are more likely to be found in the terrace deposits than along the present beaches. Other concentrations of heavy minerals, however, are possible at favored sites close to the Fall Line where the Tuscaloosa formation rests upon the crystalline rocks of the Piedmont province. A score of heavy and semiheavy minerals occur in the detrital deposits of Florida, but the principal salable minerals are ilmenite, leucoxene, rutile, and zircon, though monazite and staurolite are saved at some mining plants. Commercial deposits of heavy minerals are generally required to have a tenor of 4 percent, though ores with a lower tenor can be mined at a profit if the content of monazite is notably high. The percentages of zircon in the concentrates ranges from 10 to 16 percent, and in eastern Florida from 13 to 15 percent. Thus the tenor in zircon of the ore-bearing sands ranges from 0.4 to 0.6 percent. The content of hafnium in zircon is immaterial for many uses, but for some purposes very high or very low tenors in hafnium are required. Alluvial zircon cannot be separated into such varieties, which, if needed, must be obtained from sources in bedrock. It thus becomes necessary to determine the Hf : Zr ratios in zircon from many kinds of

Niobium and hafnium grown on porous membranes

International Nuclear Information System (INIS)

Morant, C.; Marquez, F.; Campo, T.; Sanz, J.M.; Elizalde, E.

2010-01-01

In this work we report on a method for fabricating highly ordered nanostructures of niobium and hafnium metals by physical vapour deposition using two different templates: anodized aluminum oxide membranes (AAO) and zirconium onto AAO membranes (Zr/AAO). The growth mechanism of these metal nanostructures is clearly different depending on the material used as a template. A different morphology was obtained by using AAO or Zr/AAO templates: when the metal is deposited onto AAO membranes, nanospheres with ordered hexagonal regularity are obtained; however, when the metal is deposited onto a Zr/AAO template, highly ordered nanocones are formed. The experimental approach described in this work is simple and suitable for synthesizing nanospheres or nanoholes of niobium and hafnium metals in a highly ordered structure.

Analytical study of zirconium and hafnium α-hydroxy carboxylates

International Nuclear Information System (INIS)

Terra, V.R.

1991-01-01

The analytical study of zirconium and hafnium α-hydroxy carboxylates was described. For this purpose dl-mandelic, dl-p-bromo mandelic, dl-2-naphthyl glycolic, and benzilic acids were prepared. These were used in conjunction with glycolic, dl-lactic, dl-2-hydroxy isovaleric, dl-2-hydroxy hexanoic, and dl-2-hydroxy dodecanoic acids in order to synthesize the zirconium(IV) and hafnium(IV) tetrakis(α-hydroxy carboxylates). The compounds were characterized by melting point determination, infrared spectroscopy, thermogravimetric analysis, calcination to oxides and X-ray diffractometry by the powder method. (C.G.C)

High temperature evaporation of titanium, zirconium and hafnium carbides

International Nuclear Information System (INIS)

Gusev, A.I.; Rempel', A.A.

1991-01-01

Evaporation of cubic nonstoichiometric carbides of titanium, zirconium and hafnium in a comparatively low-temperature interval (1800-2700) with detailed crystallochemical sample certification is studied. Titanium carbide is characterized by the maximum evaporation rate: at T>2300 K it loses 3% of sample mass during an hour and at T>2400 K titanium carbide evaporation becomes extremely rapid. Zirconium and hafnium carbide evaporation rates are several times lower than titanium carbide evaporation rates at similar temperatures. Partial pressures of metals and carbon over the carbides studied are calculated on the base of evaporation rates

Determination of hafnium, molybdenum, and vanadium in niobium and niobium-based alloys by atomic absorption spectrometry

International Nuclear Information System (INIS)

Ide, Kunikazu; Kobayashi, Takeshi; Sudo, Emiko.

1985-01-01

The analytical procedure is as follows: Weigh 1 g of a sample and put it into a 100 cm 3 PTFE beaker. Add 5 ml of distilled water and 5 ml of hydrofluoric acid, and then heat the solution on a hot plate, adding 3 ml of nitric acid dropwise. Dilute the solution to 100 cm 3 with distilled water. When hafnium is determined, add 2 g of diammonium titanium hexafluoride ((NH 4 ) 2 TiF 6 )) before dilution. Working standard solutions are prepared by adding the stock standard solutions of hafnium, molybdenum, and vanadium into niobium solutions. When hafnium is determined, add 2 g of (NH 4 ) 2 TiF 6 and the alloying elements in amounts corresponding to those in sample solutions into the working standard solutions. The tolerable amounts of hydrofluoric acid were 2.9 M, 2.1 M, and 3.1 M and those of nitric acid were 1.0 M, 1.6 M, and 1.6 M for hafnium, molybdenum, and vanadium, respectively. It was found that (NH 4 ) 2 TiF 6 greatly increased the sensitivity for hafnium determination. Niobium showed minus effect for hafnium and plus effect for molybdenum and vanadium. The atomic absorption of molybdenum and vanadium were not influenced by the presence of 20 % of each alloying element, while the atomic absorption of hafnium was given plus effect by 20 % of zirconium, iron, cobalt, nickel, manganese, chromium or vanadium and minus effect by 20 % tungsten. The analytical values of hafnium, molybdenum, and vanadium in niobium-based alloys by this method showed a good agreement with those by X-ray fluorescence analysis. The lower limits of determination (S/N=2) were 0.05, 0.001, and 0.002 % and the relative standard deviation were 3, 1, and 1.5 % for hafnium, molybdenum, and vanadium, respectively. (author)

Separation of zirconium from hafnium by ion exchange

Energy Technology Data Exchange (ETDEWEB)

Felipe, Elaine C.B.; Palhares, Hugo G.; Ladeira, Ana Claudia Q., E-mail: elainecfelipe@yahoo.com.br, E-mail: hugopalhares@gmail.com, E-mail: ana.ladeira@cdtn.br [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

2013-07-01

Zirconium and hafnium are two of the most important metals for the nuclear industry. Hafnium occurs in all zirconium ores usually in the range 2 - 3%. However, for the most nuclear industry applications, it is necessary to use a zirconium of extremely pure level. The current work consists in the separation of zirconium and hafnium by the ion exchange method in order to obtain a zirconium concentrate of high purity. The zirconium and hafnium liquors were produced from the leaching of the Zr(OH){sub 4} and Hf(OH){sub 4} with nitric acid for 24 hours. From these two liquors it was prepared one solution containing 7.5 x 10{sup -2} mol L{sup -1} of Zr and 5.8 x 10{sup -3} mol L{sup -1} of Hf with acidity of 1 M. Ion exchange experiments were carried out in batch with the resins Dowex 50WX4, Dowex 50WX8 100, Dowex 50WX8 50, Amberlite IR-120 and Marathon C at constant temperature 28 deg C. Other variables such as, acidity and agitation were kept constant. The data were adjusted to Langmuir equation in order to calculate the maximum loading capacity (q{sub max}) of the resins, the distribution coefficient (K{sub d}) for Zr and Hf and the separation factor (α{sub Hf}{sup Zr} ). The results of maximum loading capacity (q{sub max}) for Zr and Hf, in mmol g{sup -}1, showed that the most suitable resins for columns experiments are: Dowex 50WX4 50 (q{sub max} Z{sub r} = 2.21, Hf = 0.18), Dowex 50WX8 50 (q{sub max} Zr = 1.89, Hf = 0.13) and Amberlite (q{sub max} Zr = 1.64, Hf = 0.12). However, separations factors, α{sub Hf}{sup Zr}, showed that the resins are not selective. (author)

On the stabilization of niobium(V) solutions by zirconium(IV) and hafnium(IV)

DEFF Research Database (Denmark)

Sørensen, E.; Bjerre, A.B.

1992-01-01

Niobium cannot be separated from zirconium or hafnium when these elements occur together in solution with common anions such as chloride and sulphate. This is ascribed to the co-polymerization of niobium(V) and the hydrolysed ionic species of zirconium(IV) and hafnium(IV) to form colloidal...

Analysis of hafnium in zirconium alloys

International Nuclear Information System (INIS)

Kondo, Isao; Sakai, Fumiaki; Ohuchi, Yoshifusa; Nakamura, Hisashi

1977-01-01

It is required to analyse alloying components and impurity elements in the acceptance analysis of zirconium alloys as the material for fuel cladding tubes and pressure tubes for advanced thermal reactors. Because of extreme similarity in chemical properties between zirconium and hafnium, about 100 ppm of hafnium is usually contained in zirconium alloys. Zircaloy-2 alloy and 2.5% Nb-zirconium with the addition of hafnium had been prepared as in-house standard samples for rapid analysis. Study was made on fluorescent X-ray analysis and emission spectral analysis to establish the analytical method. By using these in-house standard samples, acceptance analysis was successfully carried out for the fuel cladding tubes for advanced thermal reactors. Sulfuric acid solution was prepared from JAERI-Z 1, 2 and 3, the standard sample for zircaloy-2 prepared by the Analytical Committee on Nuclear Fuel and Reactor Materials, JAERI, and zirconium oxide (Hf 1 ppm/Zr). Standard Hf solution was added to the sulfuric acid solution step by step, to make up a series of the standard oxide samples by the precipitation process. By the use of these standard samples, the development of the analytical method and joint analysis were made by the three-member analytical technique research group including PNC. The analytical precision for the fluorescent X-ray analysis was improved by attaching a metallic yttrium filter to the window of an X-ray tube so as to suppress the effect due to zirconium matrix. The variation factor of the joint analysis was about 10% to show good agreement, and the indication value was determined. (Kobatake, H.)

Knight shift in scandium and its alloys with hafnium and titanium

International Nuclear Information System (INIS)

Chachkhiani, Z.B.; Chechernikov, V.I.; Martynova, L.F.; Nidel'ko, V.I.; Chachkhiani, L.G.; Georgadze, G.S.

1981-01-01

Results of the investigation of NMR on 45 Sc nuclei and magnetic susceptibility of scandium and its solid solutions with titanium and hafnium are presented. It is shown that the existing hybridization of S and d zones in pure scandium and its alloys with titanium and hafnium affects the Knight shift reducing the value of the contact contribution. The temperature behaviour of the Knight shift from the temperature dependence and spin susceptibility of collectivized d electrons [ru

Composition and microstructure of zirconium and hafnium germanates obtained by different chemical routes

International Nuclear Information System (INIS)

Utkin, A.V.; Prokip, V.E.; Baklanova, N.I.

2014-01-01

The phase composition and morphology of zirconium and hafnium germanates synthesized by ceramic and co-precipitation routes were studied. The products were characterized using high-temperature X-ray diffraction analysis (XRD), Raman spectroscopy, scanning electron microscopy (SEM) and thermal (TG/DTA) analysis. To investigate the phase composition and stoichiometry of compounds the unit cell parameters were refined by full-profile Rietveld XRD analysis. The morphology of products and its evolution during high-temperature treatment was examined by SEM analysis. It was stated that there is the strong dependence of the phase composition and morphology of products on the preparation route. The ceramic route requires a multi-stage high-temperature treatment to obtain zirconium and hafnium germanates of 95% purity or more. Also, there are strong diffusion limitations to obtain hafnium germanate Hf 3 GeO 8 by ceramic route. On the contrary, the co-precipitation route leads to the formation of nanocrystalline single phase germanates of stoichiometric composition at a relatively low temperatures (less than 1000 °C). The results of quantitative XRD analysis showed the hafnium germanates are stoichiometric compounds in contrast to zirconium germanates that form a set of solid solutions. This distinction may be related to the difference in the ion radii of Zr and Hf. - Graphical abstract: The phase composition and morphology of zirconium and hafnium germanates synthesized by ceramic and co-precipitation routes were studied. It was stated that there is the strong dependence of the phase composition and morphology of products on the preparation route. Display Omitted - Highlights: • Zr and Hf germanates were synthesized by ceramic and co-precipitation routes. • The morphology of products depends on the synthesis parameters. • Zirconium germanates forms a set of solid solutions. • Hafnium germanates are stoichiometric compounds

Recovery of hafnium radioisotopes from a proton irradiated tantalum target

International Nuclear Information System (INIS)

Taylor, W.A.; Garcia, J.G.; Hamilton, V.T.; Heaton, R.C.; Jamriska, D.J.; Ott, M.A.; Philips, D.R.; Radzinski, S.D.

1998-01-01

The 178m2 Hf nucleus, with its long half-life (31 y) and high-spin isomeric state (16 + ) is desired for new and exotic nuclear physics studies. The Los Alamos Radioisotope Program irradiated a kilogram of natural tantalum at the Los Alamos Meson Physics Facility in early 1981. After fifteen years of decay, this target was ideal for the recovery of 178m2 Hf. There was more than a millicurie of 178m2 Hf produced during this irradiation and there has been a sufficient period of time for most of the other hafnium radioisotopes to decayed away. Traditionally, separation techniques for recovering hafnium isotopes from tantalum targets employ solvent extractions with reagents that are considered hazardous. These techniques are no longer condoned because they generate a mixed-waste (radioactive and hazardous components) that can not be treated for disposal. In this paper we describe a new and unique procedure for the recovery of hafnium radioisotopes from a highly radioactive, proton irradiated, tantalum target using reagents that do not contribute a hazardous waste component. (author)

Investigation of colourless complexes of thorium, hafnium and zirconium

International Nuclear Information System (INIS)

Kiciak, S.; Stefanowicz, T.; Gontarz, H.; Swit, Z.

1980-01-01

The investigations conducted in the Institute of General Chemistry of Poznan Technical University in partial cooperation with Kharkhof Technical University related with thorium, hafnium and zirconium complexes are reviewed. (author)

Separation process of zirconium and hafnium; Procede de separation du zirconium et du hafnium

Energy Technology Data Exchange (ETDEWEB)

Hure, J; Saint-James, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1955-07-01

About the separation different processes of zirconium-hafnium, the extraction by solvent in cross-current is the most easily the process usable on an industrial scale. It uses tributyl phosphate as solvent, diluted with white spirit to facilitate the decanting. Some exploratory tests showed that nitric environment seemed the most favorable for extraction; but a lot of other factors intervene in the separation process. We studied the influence of the acidity successively, the NO{sub 3}{sup -} ions concentration, the role of the cation coming with NO{sub 3}{sup -}, as well as the influence of the concentration of zirconium in the solution on the separation coefficient {beta} = {alpha}{sub Zr} / {alpha}{sub Hf}. (M.B.) [French] Des differents procedes de separation zirconium-hafnium, l'extraction par solvant en contre-courant est le procede le plus facilement utilisable a l'echelle industrielle. On utilise comme solvant le phosphate de tributyle, dilue avec du white spirit pour faciliter les decantations. Des essais preliminaires ont montre que le milieu nitrique semblait le plus favorable a l'extraction; mais beaucoup d'autres facteurs interviennent dans le processus de separation. Nous avons etudie successivement l'influence de l'acidite, celle de la concentration en ions NO{sub 3}{sup -}, le role du cation accompagnant NO{sub 3}{sup -}, ainsi que l'influence de la concentration en zirconium de la solution sur le coefficient de separation {beta} = {alpha}{sub Zr} / {alpha}{sub Hf}. (MB)

Strong influence of polymer architecture on the microstructural evolution of hafnium-alkoxide-modified silazanes upon ceramization.

Science.gov (United States)

Papendorf, Benjamin; Nonnenmacher, Katharina; Ionescu, Emanuel; Kleebe, Hans-Joachim; Riedel, Ralf

2011-04-04

The present study focuses on the synthesis and ceramization of novel hafnium-alkoxide-modified silazanes as well as on their microstructure evolution at high temperatures. The synthesis of hafnia-modified polymer-derived SiCN ceramic nanocomposites is performed via chemical modification of a polysilazane and of a cyclotrisilazane, followed by cross-linking and pyrolysis in argon atmosphere. Spectroscopic investigation (i.e., NMR, FTIR, and Raman) shows that the hafnium alkoxide reacts with the N-H groups of the cyclotrisilazane; in the case of polysilazane, reactions of N-H as well as Si-H groups with the alkoxide are observed. Consequently, scanning and transmission electron microscopy studies reveal that the ceramic nanocomposites obtained from cyclotrisilazane and polysilazane exhibited markedly different microstructures, which is a result of the different reaction pathways of the hafnium alkoxide with cyclotrisilazane and with polysilazane. Furthermore, the two prepared ceramic nanocomposites are unexpectedly found to exhibit extremely different high-temperature behavior with respect to decomposition and crystallization; this essential difference is found to be related to the different distribution of hafnium throughout the ceramic network in the two samples. Thus, the homogeneous distribution of hafnium observed in the polysilazane-derived ceramic leads to an enhanced thermal stability with respect to decomposition, whereas the local enrichment of hafnium within the matrix of the cyclotrisilazane-based sample induces a pronounced decomposition upon annealing at high temperatures. The results indicate that the chemistry and architecture of the precursor has a crucial effect on the microstructure of the resulting ceramic material and consequently on its high-temperature behavior. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Separation of hafnium from zirconium in sulfuric acid solutions using pressurized ion exchange

International Nuclear Information System (INIS)

Hurst, F.J.

1981-01-01

High-resolution pressurized ion exchange has been used successfully to study and separate hafnium and zirconium sulfate complexes by chromatographic elution from Dowex 50W-X8 (15 to 25 μm) resin with sulfuric acid solutions. Techniques were developed to continuously monitor the column effluents for zirconium and hafnium by reaction with fluorometric and colorimetric reagents. Since neither reagent was specific for either metal ion, peak patterns were initially identified by using the stable isotopes 90 Zr and 180 Hf as fingerprints of their elution position. Distribution ratios for both zirconium and hafnium decrease as the inverse fourth power of the sulfuric acid concentration below 2N and as the inverse second power at higher acid concentration. The hafnium-to-zirconium separation factor is approximately constant (approx. 8) over the 0.5 to 3N range. Under certain conditions, an unseparated fraction was observed that was not retained by the resin. The amount of this fraction which is thought to be a polymeric hydrolysis product appears to be a function of metal and sulfuric acid concentrations. Conditions are being sought to give the highest zirconium concentration and the lowest acid concentration that can be used as a feed material for commercial scale-up in the continuous annular chromatographic (CAC) unit without formation of the polymer

Separation of zirconium and hafnium from acompanying elements by paper chromatography in the systems of alcohol-acid

International Nuclear Information System (INIS)

Lebedeva, G.G.; Viktorova, M.E.

1980-01-01

Solvents have been chosen and investigated which provide expressed separation of zirconium and hafnium at the analysis of mineral raw materials by paper chromatography. The systems with HNO 3 and HCl containing methyl, ethyl, propyl and butyl alcohols have been studied as mobile phases for separation of zirconium and hafnium. It has been shown that alcohol contents and solvent acidity affect the Rsub(f) value of these elements. The C 2 H 5 OH-5MHCl and C 2 H 5 OH-5MHNO 3 systems are most optimal for pre-concentration of zirconium and hafnium

Low-voltage bendable pentacene thin-film transistor with stainless steel substrate and polystyrene-coated hafnium silicate dielectric.

Science.gov (United States)

Yun, Dong-Jin; Lee, Seunghyup; Yong, Kijung; Rhee, Shi-Woo

2012-04-01

The hafnium silicate and aluminum oxide high-k dielectrics were deposited on stainless steel substrate using atomic layer deposition process and octadecyltrichlorosilane (OTS) and polystyrene (PS) were treated improve crystallinity of pentacene grown on them. Besides, the effects of the pentacene deposition condition on the morphologies, crystallinities and electrical properties of pentacene were characterized. Therefore, the surface treatment condition on dielectric and pentacene deposition conditions were optimized. The pentacene grown on polystyrene coated high-k dielectric at low deposition rate and temperature (0.2-0.3 Å/s and R.T.) showed the largest grain size (0.8-1.0 μm) and highest crystallinity among pentacenes deposited various deposition conditions, and the pentacene TFT with polystyrene coated high-k dielectric showed excellent device-performance. To decrease threshold voltage of pentacene TFT, the polystyrene-thickness on high-k dielectric was controlled using different concentration of polystyrene solution. As the polystyrene-thickness on hafnium silicate decreases, the dielectric constant of polystyrene/hafnium silicate increases, while the crystallinity of pentacene grown on polystyrene/hafnium silicate did not change. Using low-thickness polystyrene coated hafnium silicate dielectric, the high-performance and low voltage operating (pentacene thin film transistor (μ: ~2 cm(2)/(V s), on/off ratio, >1 × 10(4)) and complementary inverter (DC gains, ~20) could be fabricated.

Primary hafnium metal sponge and other forms, approved standard 1973

International Nuclear Information System (INIS)

Anon.

1975-01-01

A specification is presented covering virgin hafnium metal commonly designated as sponge because of its porous, sponge-like texture; it may also be in other forms such as chunklets. The specification does not cover crystal bar

Evolution of the hafnium isotopic composition in the RBMK reactor

International Nuclear Information System (INIS)

Jurkevicius, A.; Remeikis, V.

2002-01-01

The isotopic composition of hafnium in the radial neutron flux sensor of the RBMK-1500 reactor, the rates of the neutron absorption on Hf isotopes and the neutron spectrum in the sensor were numerically modeled. The sequence SAS2 (Shielding Analysis Sequence) program from the package SCALE 4.4A and the HELIOS code system were used for calculations. It has been obtained that the overall neutron absorption rates in hafnium for the sensors located in the 2.4 % and 2.6 % enrichment uranium-erbium nuclear fuel assemblies are by 16 % and 19 % lower than in the 2.0 % enrichment uranium nuclear fuel assemblies. The overall neutron absorption rate in hafnium decreases 2.70-2.75 times due to the sensor burnup to 5800 MW d. The sensitivity of the Hf sensors to the thermal neutron flux increases twice due to the nuclear fuel assembly burnup to 3000 MW d. The corrective factors ξ d (I) at the different integral current I of the sensors and ξ td (E) at the different burnup E of the nuclear fuel assemblies were calculated. The obtained dependence ξ d (I) calculated numerically was compared to the experimental one determined by comparing signals of the fresh sensor and the sensor with the integral current I and by processing repeated calibration results of Hf sensors in RBMK-1500 reactors. The relative relationship coefficients K T (T FA ) were found for all RBMK-1500 nuclear fuel types. (author)

Preparation of hafnium metal by calciothermic reduction of HfO2

International Nuclear Information System (INIS)

Sharma, I.G.; Vijay, P.L.; Sehra, J.C.; Sundaram, C.V.

1975-01-01

Hafnium metal powder has been produced by the calciothermic reduction of hafnium oxide. The influence of various experimental parameters - such as amount of calcium in excess of stoichiometric requirement, temperature, and time of reduction - on the yield and purity of the metal has been studied. The metal powder obtained by reduction at 960 0 C (two hours) with a calcium excess of 70% analysed 600 ppm of oxygen and 147 ppm of nitrogen. A reduction efficiency of 96% has been achieved under these conditions. The refining of the powder by electron beam melting, fused salt electrolysis, and iodide process has been studied. The oxygen content in the metal could be brought down from 6900 to 148 ppm by electron beam melt-refining. (author)

ENTIRELY AQUEOUS SOLUTION-GEL ROUTE FOR THE PREPARATION OF ZIRCONIUM CARBIDE, HAFNIUM CARBIDE AND THEIR TERNARY CARBIDE POWDERS

Directory of Open Access Journals (Sweden)

Zhang Changrui

2016-07-01

Full Text Available An entirely aqueous solution-gel route has been developed for the synthesis of zirconium carbide, hafnium carbide and their ternary carbide powders. Zirconium oxychloride (ZrOCl₂.8H₂O, malic acid (MA and ethylene glycol (EG were dissolved in water to form the aqueous zirconium carbide precursor. Afterwards, this aqueous precursor was gelled and transformed into zirconium carbide at a relatively low temperature (1200 °C for achieving an intimate mixing of the intermediate products. Hafnium and the ternary carbide powders were also synthesized via the same aqueous route. All the zirconium, hafnium and ternary carbide powders exhibited a particle size of ∼100 nm.

On the phase formation of sputtered hafnium oxide and oxynitride films

International Nuclear Information System (INIS)

Sarakinos, K.; Music, D.; Mraz, S.; Baben, M. to; Jiang, K.; Nahif, F.; Braun, A.; Zilkens, C.; Schneider, J. M.; Konstantinidis, S.; Renaux, F.; Cossement, D.; Munnik, F.

2010-01-01

Hafnium oxynitride films are deposited from a Hf target employing direct current magnetron sputtering in an Ar-O 2 -N 2 atmosphere. It is shown that the presence of N 2 allows for the stabilization of the transition zone between the metallic and the compound sputtering mode enabling deposition of films at well defined conditions of target coverage by varying the O 2 partial pressure. Plasma analysis reveals that this experimental strategy facilitates control over the flux of the O - ions which are generated on the oxidized target surface and accelerated by the negative target potential toward the growing film. An arrangement that enables film growth without O - ion bombardment is also implemented. Moreover, stabilization of the transition sputtering zone and control of the O - ion flux without N 2 addition is achieved employing high power pulsed magnetron sputtering. Structural characterization of the deposited films unambiguously proves that the phase formation of hafnium oxide and hafnium oxynitride films with the crystal structure of HfO 2 is independent from the O - bombardment conditions. Experimental and theoretical data indicate that the presence of vacancies and/or the substitution of O by N atoms in the nonmetal sublattice favor the formation of the cubic and/or the tetragonal HfO 2 crystal structure at the expense of the monoclinic HfO 2 one.

Solvent extraction of titanium(IV), zirconium(IV) and hafnium(IV) salicylates using liquid ion exchangers

Energy Technology Data Exchange (ETDEWEB)

Sundaramurthi, N M; Shinde, V M

1989-02-01

A solvent extraction method is proposed for the extraction of quadrivalent titanium, zirconium an hafnium from salicylate media using liquid ion exchangers such as Aliquat 336 and trioctylamine dissolved in xylene. The optimum conditions were evaluated from a critical study of the following: pH, salicylate concentration, amine concentration, diluent and period of equilibration. The method allows the separation of titanium, zirconium and hafnium from binary mixtures containing commonly associated metal ions and is applicable to the analysis of real samples such as BCS-CRM 387 nimonic 901, BCS-CRM 243/4 ferro-titanium, BCS-CRM 307 magnesium alloy and BCS-CRM 388 zircon. Titanium is determined either with hydrogen peroxide or by atomic absorption spectrometry whereas zirconium and hafnium are determined spectrophotometrically with Alizarin Red S and Zylenol Orange, respectively. The results of both separation and analysis are reported. The method is precise, accurate and fast.

Solvent extraction of zirconium and hafnium using MIBK-HSCN-HCL process

International Nuclear Information System (INIS)

Borges, J.A.L.; Cunha, O.G.C. da

1985-01-01

The separation process of zirconium and hafnium, using MIBK as extractant in a set of mixer-settler is described. The chemical analysis was done by X-ray fluorescence and emission spectrography. (Author) [pt

Radiation effects on the electrical properties of hafnium oxide based MOS capacitors.

Energy Technology Data Exchange (ETDEWEB)

Petrosky, J. C. (Air Force Institute of Technology, Wright-Patterson Air Force Base, OH); McClory, J. W. (Air Force Institute of Technology, Wright-Patterson Air Force Base, OH); Bielejec, Edward Salvador; Foster, J. C. (Air Force Institute of Technology, Wright-Patterson Air Force Base, OH)

2010-10-01

Hafnium oxide-based MOS capacitors were investigated to determine electrical property response to radiation environments. In situ capacitance versus voltage measurements were analyzed to identify voltage shifting as a result of changes to trapped charge with increasing dose of gamma, neutron, and ion radiation. In situ measurements required investigation and optimization of capacitor fabrication to include dicing, cleaning, metalization, packaging, and wire bonding. A top metal contact of 200 angstroms of titanium followed by 2800 angstroms of gold allowed for repeatable wire bonding and proper electrical response. Gamma and ion irradiations of atomic layer deposited hafnium oxide on silicon devices both resulted in a midgap voltage shift of no more than 0.2 V toward less positive voltages. This shift indicates recombination of radiation induced positive charge with negative trapped charge in the bulk oxide. Silicon ion irradiation caused interface effects in addition to oxide trap effects that resulted in a flatband voltage shift of approximately 0.6 V also toward less positive voltages. Additionally, no bias dependent voltage shifts with gamma irradiation and strong oxide capacitance room temperature annealing after ion irradiation was observed. These characteristics, in addition to the small voltage shifts observed, demonstrate the radiation hardness of hafnium oxide and its applicability for use in space systems.

Investigation of chlorination of zirconium and hafnium and their compounds in discharge from hollow cathode

International Nuclear Information System (INIS)

Ioffe, R.B.; Korovin, Yu.I.

1978-01-01

The possibility is investigated of chlorinating various zirconium and hafnium compounds (metal, oxide, carbide) in a hot discharge from a hollow cathode with various chlorinating reagents: copper monochloride, nickel chloride, magnesium chloride, for the purpose of accelerating their entrance into the excitation zone. It has been shown thermodynamically and experimentally that chlorination of metal zirconium and hafnium and their carbides with copper monochloride in hot hollow cathode conditions provides a sharp increase in the intensity of the lines of these elements

Development and characterization of ultrathin hafnium titanates as high permittivity gate insulators

Science.gov (United States)

Li, Min

High permittivity or high-kappa materials are being developed for use as gate insulators for future ultrascaled metal oxide semiconductor field effect transistors (MOSFETs). Hafnium containing compounds are the leading candidates. Due to its moderate permittivity, however, it is difficult to achieve HfO2 gate structures with an EOT well below 1.0 nm. One approach to increase HfO2 permittivity is combining it with a very high-kappa material, such as TiO2. In this thesis, we systematically studied the electrical and physical characteristics of high-kappa hafnium titanates films as gate insulators. A series of HfxTi1-xO2 films with well-controlled composition were deposited using an MOCVD system. The physical properties of the films were analyzed using a variety of characterization techniques. X-ray micro diffraction indicates that the Ti-rich thin film is more immune to crystallization. TEM analysis showed that the thick stoichiometric HfTiO 4 film has an orthorhombic structure and large anisotropic grains. The C-V curves from the devices with the hafnium titanates films displayed relatively low hysteresis. In a certain composition range, the interfacial layer (IL) EOT and permittivity of HfxTi1-x O2 increases linearly with increasing Ti. The charge is negative for HfxTi1-xO2/IL and positive for Si/IL interface, and the magnitude increases as Hf increases. For ultra-thin films (less than 2 nm EOT), the leakage current increases with increasing HE Moreover, the Hf-rich sample has weaker temperature dependence of the current. In the MOSFET devices with the hafnium titanates films, normal transistor characteristics were observed, also electron mobility degradation. Next, we investigated the effects that different pre-deposition surface treatments, including HF dipping, NH3 surface nitridation, and HfO2 deposition, have on the electrical properties of hafnium titanates. Surface nitridation shows stronger effect than the thin HfO2 layer. The nitrided samples displayed a

Separation of zirconium and hafnium using paper distribution chromatography

International Nuclear Information System (INIS)

Lebedeva, G.G.; Viktorova, M.E.

1981-01-01

A method is suggested of chromatographic separation of zirconium and hafnium in a CCl 4 -tributyl phosphate system (1:9) containing KCl as a salting-out agent in 5 M HNO 3 at 28-30 deg C. Zr and Hf are deterfmined in articiial mixtures under optimal chromatography conditions using visual colorimetry [ru

Hafnium as a prospective absorber for VVER-1000 reactors of Ukraine

International Nuclear Information System (INIS)

Afanas'ev, A.A.; Konotop, Yu.F.; Odejchuk, N.L.

2000-01-01

Nuclear-physical parameters of hafnium having in mind its use as an absorber, are considered. Technical aspects of Hf production are exposed. Use of B 4 C/Hf absorber is twice cheaper than a standard one

Evaluation of thermodynamic data on zirconium and hafnium halides and oxyhalides by means of transport experiments

International Nuclear Information System (INIS)

Dittmer, G.; Niemann, U.

1987-01-01

A consistent set of thermodynamic data for zirconium and hafnium halides, oxides and oxyhalides was achieved. It was found that formation enthalpies of gaseous compounds could be derived from solubility measurements together with theoretical estimations and a revision of literature data. Free energy functions were calculated employing statistical mechanics. Data for liquid and solid compounds were obtained via sublimation and vaporization data. Chemical equilibria of zirconium and hafnium with halogens are discussed. 51 refs.; 16 figs.; 14 tabs

Electrodeposition in molten salts of metals used in nuclear industry: hafnium and uranium

International Nuclear Information System (INIS)

Serrano, K.

1998-01-01

The aim of this work is to study the electrodeposition in molten salts of metals used in nuclear industry: hafnium and uranium. The experiment is carried out in a molten alkaline halogenide medium in a temperature range between 670 and 750 degrees Celsius. The first part of this work concerns more particularly the electrochemical behaviour of the hafnium and uranium ions in the electrolytic solution. The reduction mechanisms of these ions have been studied by the use of three methods: cyclic voltametry, chrono-potentiometry and square wave voltametry. Results have shown that the process of metal deposition is difficult to explain because secondary reactions (as for instance: adsorption phenomena or cathodic deposit dissolution) occur. The uranium germination has then been studied by modelling of chrono-amperograms. The experiments have shown that the deposition is the result of the initial uranium crystal growth and depends on the electrolyte diffusion. The second part of this work deals with the implementation of hafnium and uranium deposition taking into account the preceding mechanistic studies. Depositions have all been observed by physical methods as for instance scanning electron microscopy. Particular experimental solutions (soluble anode, addition of fluoride ions to the electrolyte) have been used. The obtained deposition of hafnium is smooth and adheres very well to the substrate. The uranium depositions have been implemented with the use of a soluble anode. Uranium is deposited in a dendritic shape to the cathode. It has also been shown that the electro-kinetic parameters (temperature, uranium ions concentration, current density) have not an important influence on the dendritic morphology of the deposition. This morphology could be the consequence of particular convection movements to the surface of the cathode. (O.M.)

Synthesis and characterization of Ho3+ doped hafnium oxide TLD for radiation dosimeter

International Nuclear Information System (INIS)

Sekar, Nandakumar; Ganesan, Bharanidharan; Sahib, Hajee Reyaz Ali; Aruna, Prakasarao; Ganesan, Singaravelu; Thamilkumar, P.; Rai, R.R.

2017-01-01

Cancer is a dreaded disease which is treated by Radiotherapy, Chemotherapy and Surgery. Radiotherapy plays a vital role in treatment of cancer and recently measurements of invivo radiation dosimetric in patient is of great interest due to high dose gradients in advanced technology like IMRT, IGRT etc. Hence, for the last few decades, a great degree of interest has been shown for the hafnium oxide for radiation dosimetric applications, due to its high dielectric constant, wide band gap and better interface properties such as chemical stability, conduction band offset and thermodynamic stability. In the present study, Synthesis and characterization of Ho 3+ doped Hafnium oxide were carried out and its applications towards radiation dosimeter were investigated

Use of hafnium in control bars of nuclear reactors; Uso de hafnio en barras de control de reactores nucleares

Energy Technology Data Exchange (ETDEWEB)

Ramirez S, J.R.; Alonso V, G. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: jrrs@nuclear.inin-mx

2003-07-01

Recently the use of hafnium as neutron absorber material in nuclear reactors has been reason of investigation by virtue of that this material has nuclear properties as to the neutrons absorption and structural that can prolong the useful life of the control mechanisms of the nuclear reactors. In this work some of those more significant hafnium properties are presented like nuclear material. Also there are presented calculations carried out with the HELIOS code for fuel cells of uranium oxide and of uranium and plutonium mixed oxides under controlled conditions with conventional bars of boron carbide and also with similar bars to which are substituted the absorbent material by metallic hafnium, the results are presented in this work. (Author)

Plasma spraying of zirconium carbide – hafnium carbide – tungsten cermets

Czech Academy of Sciences Publication Activity Database

Brožek, Vlastimil; Ctibor, Pavel; Cheong, D.-I.; Yang, S.-H.

2009-01-01

Roč. 9, č. 1 (2009), s. 49-64 ISSN 1335-8987 Institutional research plan: CEZ:AV0Z20430508 Keywords : Plasma spraying * cermet coatings * microhardness * zirconium carbide * hafnium carbide * tungsten * water stabilized plasma Subject RIV: JH - Ceramics, Fire-Resistant Materials and Glass

Extraction of zirconium and hafnium thiocyanates by CH3COCH2CH.(CH3)2-HSCN solvent from chloride medium

International Nuclear Information System (INIS)

Okada, A.T.

1982-01-01

A zirconium-hafnium separation process for application in nuclear industry is presented. The extraction of zirconium and hafnium thiocyanates in chloride medium by hexone-HSCN solvent was studied. The extraction process was developed, varying the parameters, such as, concentrations of the metals, the thiocyanate ion, the sulphate ion and free acidity in aqueous phase. (Author) [pt

Separation process of zirconium and hafnium

International Nuclear Information System (INIS)

Hure, J.; Saint-James, R.

1955-01-01

About the separation different processes of zirconium-hafnium, the extraction by solvent in cross-current is the most easily the process usable on an industrial scale. It uses tributyl phosphate as solvent, diluted with white spirit to facilitate the decanting. Some exploratory tests showed that nitric environment seemed the most favorable for extraction; but a lot of other factors intervene in the separation process. We studied the influence of the acidity successively, the NO 3 - ions concentration, the role of the cation coming with NO 3 - , as well as the influence of the concentration of zirconium in the solution on the separation coefficient β = α Zr / α Hf . (M.B.) [fr

Synthesis and characterization of hafnium oxide films for thermo and photoluminescence applications

International Nuclear Information System (INIS)

Guzman Mendoza, J.; Aguilar Frutis, M.A.; Flores, G. Alarcon; Garcia Hipolito, M.; Maciel Cerda, A.; Azorin Nieto, J.; Rivera Montalvo, T.; Falcony, C.

2010-01-01

Hafnium oxide (HfO 2 ) films were deposited by the ultrasonic spray pyrolysis process. The films were synthesized from hafnium chloride as raw material in deionized water as solvent and were deposited on corning glass substrates at temperatures from 300 to 600 deg. C. For substrate temperatures lower than 400 deg. C the deposited films were amorphous, while for substrate temperatures higher than 450 deg. C, the monoclinic phase of HfO 2 appeared. Scanning electron microscopy showed that the film's surface resulted rough with semi-spherical promontories. The films showed a chemical composition close to HfO 2 , with an Hf/O ratio of about 0.5. UV radiation was used in order to achieve the thermoluminescent characterization of the films; the 240 nm wavelength induced the best response. In addition, preliminary photoluminescence spectra, as a function of the deposition temperatures, are shown.

A study of a production process for hafnium-free zirconium from zircon

International Nuclear Information System (INIS)

Ratanalert, N.

1985-01-01

The purpose of this experiment was to extract and purify the zirconium from zircon. The effects of time of extraction and stripping of zirconium, concentration of feed solution, concentration of hydrochloric acid in stripping process, equilibrium curve of extraction of zirconium and hafnium and equilibrium curve of stripping zirconium or scrubbing hafnium were studied from standard zirconium and hafnium. The results, subsequently were applied to the extraction procedures for zirconium from zircon. Minus 100 mesh zircon was fused with sodium hydroxide in the ratio of 1 : 6 at 700 degree C for l hour. After fusion the zirconate was leached with water and dissolved in hot concentrated hydrochloric acid. Zirconyl chloride octahydrate crystallized out when the solution was cooled. An agueons solution of zirconyl chloride was used as the feed to the hexone - thiocyanate solvent extraction process. This was prepared by dissolving zirconyl chloride octahydrate crystal in waster. This zirconium feed solution in 1 M HCl and 1 M N H 4 CNS was extracted with 2.7 m N H 4 CNS in hexone and then stripped with 3.6 M HCl the aqueous phase was got rid of thiocyanate ion by extracting with pure hexone, then the zirconium in aqueous phase was precipitated with sulfuric acid and ammonium hydroxide at pH 1.8 - 2.0 and zirconium oxide was obtained by ignition at 700 degree C. The process could be modified to improve the purity of zirconium by using cation exchange resin to get rid of thiocyanate ion after solvent extraction process

Vapor pressure, heat capacities, and phase transitions of tetrakis(tert-butoxy)hafnium

Czech Academy of Sciences Publication Activity Database

Fulem, Michal; Růžička, K.

2011-01-01

Roč. 311, Dec. (2011), s. 25-29 ISSN 0378-3812 Institutional research plan: CEZ:AV0Z10100521 Keywords : tetrakis(tert-butoxy)hafnium * MO precursor * vapor pressure * heat capacity * vaporization enthalpy * enthalpy of fusion Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.139, year: 2011

Pentamethylcyclopentadienyl Zirconium and Hafnium Polyhydride Complexes : Synthesis, Structure, and Reactivity

NARCIS (Netherlands)

Visser, Cindy; Hende, Johannes R. van den; Meetsma, Auke; Hessen, Bart; Teuben, Jan H.

2001-01-01

The half-sandwich zirconium and hafnium N,N-dimethylaminopropyl complexes Cp*M[(CH2)3NMe2]Cl2 (Cp* = η5-C5Me5, M = Zr, 1; Hf, 2) and Cp*M[(CH2)3NMe2]2Cl (M = Zr, 3; Hf, 4) were synthesized by mono- or dialkylation of Cp*MCl3 with the corresponding alkyllithium and Grignard reagents. Hydrogenolysis

Properties of neutron-rich hafnium high-spin isomers

CERN Multimedia

Tungate, G; Walker, P M; Neyens, G; Billowes, J; Flanagan, K; Koester, U H; Litvinov, Y

It is proposed to study highly-excited multi-quasiparticle isomers in neutron-rich hafnium (Z=72) isotopes. Long half-lives have already been measured for such isomers in the storage ring at GSI, ensuring their accessibility with ISOL production. The present proposal focuses on:\\\\ (i) an on-line experiment to measure isomer properties in $^{183}$Hf and $^{184}$Hf, and\\\\ (ii) an off-line molecular breakup test using REXTRAP, to provide Hf$^{+}$ beams for future laser spectroscopy and greater sensitivity for the future study of more neutron-rich isotopes.

Ion-bombardment-induced reduction in vacancies and its enhanced effect on conductivity and reflectivity in hafnium nitride films

Energy Technology Data Exchange (ETDEWEB)

Gu, Zhiqing; Wang, Jiafu; Hu, Chaoquan; Zhang, Xiaobo; Dang, Jianchen; Gao, Jing; Zheng, Weitao [Jilin University, School of Materials Science and Engineering, Key Laboratory of Mobile Materials, MOE, and State Key Laboratory of Superhard Materials, Changchun (China); Zhang, Sam [Nanyang Technological University, School of Mechanical and Aerospace Engineering, Singapore (Singapore); Wang, Xiaoyi [Chinese Academy of Sciences, Key Laboratory of Optical System Advanced Manufacturing Technology, Changchun Institute of Optics, Fine Mechanics and Physics, Changchun (China); Chen, Hong [Jilin University, Department of Control Science and Engineering, Changchun (China)

2016-08-15

Although the role of ion bombardment on electrical conductivity and optical reflectivity of transition metal nitrides films was reported previously, the results were controversial and the mechanism was not yet well explored. Here, we show that proper ion bombardment, induced by applying the negative bias voltage (V{sub b}), significantly improves the electrical conductivity and optical reflectivity in rocksalt hafnium nitride films regardless of level of stoichiometry (i.e., in both near-stoichiometric HfN{sub 1.04} and over-stoichiometric HfN{sub 1.17} films). The observed improvement arises from the increase in the concentration of free electrons and the relaxation time as a result of reduction in nitrogen and hafnium vacancies in the films. Furthermore, HfN{sub 1.17} films have always much lower electrical conductivity and infrared reflectance than HfN{sub 1.04} films for a given V{sub b}, owing to more hafnium vacancies because of larger composition deviation from HfN exact stoichiometry (N:Hf = 1:1). These new insights are supported by good agreement between experimental results and theoretical calculations. (orig.)

Results for heterogeneous poisoning of the critical HTR-test facility KAHTER using absorber elements containing hafnium and boron

International Nuclear Information System (INIS)

Drueke, V.; Filges, D.; Nabi, R.; Neef, R.D.; Paul, N.; Schaal, H.

1979-10-01

Experiments and checking computations for investigating the initial-core poisoning of the pebble bed high temperature reactor are described. Following the example of the THTR-300, THTR absorber elements poisoned with hafnium/boron were added to the THTR fuel- and graphite elements of the KAHTER core. Three different hafnium-boron poisoned core loadings, corresponding to 2.7, 5.3 and 8% reactivity compensation, were used in the experiments. For purposes of comparison, two cores exclusively boron poisoned were also studied. The poisoning of these cores correspond to 2.7 and 8% reactivity compensation. The experiments and checking computations should serve to test the accuracy of the theoretical models and data sets in modeling the reactivity effects of absorber poisoned elements in the THTR. In particular, the applicability of the nuclear data of hafnium and the treatment of resonance calculations should be verified. In addition, to determining critical masses and ksub(eff), special emphasis was placed in the experiments on the exact determination of all reactivity effects. In some cases, repeated loading of a configuration also provided a measure of the reproducibility of ksub(eff). The experiments were checked computationally using the GAMTEREX code package and the program system RSYST. These two computation packages contain different data bases, - although the hafnium data are identical -, and the computing models differ in certain phases of the calculations. Both code systems compute ksub(eff) values to within the present accuracy requirements, whereas the program system RSYST gives better agreement with experimental measurements. (orig.) 891 RW/orig. 892 RDG [de

Thermal behaviour of hafnium diethylenetriaminepentaacetate studied using the perturbed angular correlation technique

Energy Technology Data Exchange (ETDEWEB)

Chain, Cecilia Y. [Universidad Nacional de La Plata (Argentina). Dept. de Fisica; Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET), La Plata (Argentina). IFLP-CCT; Consejo Nacional de Investigaciones Cientificas y Tecnicas, Buenos Aires (Argentina); Rivas, Patricia [Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET), La Plata (Argentina). IFLP-CCT; Consejo Nacional de Investigaciones Cientificas y Tecnicas, Buenos Aires (Argentina); Universidad Nacional de La Plata (Argentina). Facultad de Ciencias Agrarias y Forestales; Pasquevich, Alberto F. [Universidad Nacional de La Plata (Argentina). Dept. de Fisica; Consejo Nacional de Investigaciones Cientificas y Tecnicas (CONICET), La Plata (Argentina). IFLP-CCT; Comision de Investigaciones Cientificas de la Provincia de Buenos Aires (CIC-PBA) (Argentina)

2014-07-01

Polyaminecarboxilic ligands like diethylenetriaminepentaacetic acid form stable complexes with many heavy metal ions, excelling as cation chelants especially in the field of radiopharmacy. The aim of this work is to characterize, by using the Time Differential Perturbed Angular Correlations (TDPAC) technique, the hyperfine interactions at hafnium sites in hafnium diethylenetriaminepentaacetate and to investigate their evolution as temperature increases. TDPAC results for KHfDTPA.3H{sub 2}O obtained by chemical synthesis yield a well defined and highly asymmetric interaction of quadrupole frequency ω{sub Q} = 141 Mrad/s, which is consistent with the existence of a unique site for the metal in the crystal lattice. The thermal behaviour of the chelate is investigated by means of differential scanning calorimetry and thermogravimetrical analyses revealing that an endothermic dehydration of KHfDTPA.3H{sub 2}O takes place in one step between 80 C and 180 C. The anhydrous KHfDTPA thus arising is characterized by a fully asymmetric and well defined interaction of quadrupole frequency ω{sub Q} = 168 Mrad/s. (orig.)

Thermal behaviour of hafnium diethylenetriaminepentaacetate studied using the perturbed angular correlation technique

International Nuclear Information System (INIS)

Chain, Cecilia Y.; Rivas, Patricia

2014-01-01

Polyaminecarboxilic ligands like diethylenetriaminepentaacetic acid form stable complexes with many heavy metal ions, excelling as cation chelants especially in the field of radiopharmacy. The aim of this work is to characterize, by using the Time Differential Perturbed Angular Correlations (TDPAC) technique, the hyperfine interactions at hafnium sites in hafnium diethylenetriaminepentaacetate and to investigate their evolution as temperature increases. TDPAC results for KHfDTPA.3H 2 O obtained by chemical synthesis yield a well defined and highly asymmetric interaction of quadrupole frequency ω Q = 141 Mrad/s, which is consistent with the existence of a unique site for the metal in the crystal lattice. The thermal behaviour of the chelate is investigated by means of differential scanning calorimetry and thermogravimetrical analyses revealing that an endothermic dehydration of KHfDTPA.3H 2 O takes place in one step between 80 C and 180 C. The anhydrous KHfDTPA thus arising is characterized by a fully asymmetric and well defined interaction of quadrupole frequency ω Q = 168 Mrad/s. (orig.)

33 CFR 173.17 - Reciprocity.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Reciprocity. 173.17 Section 173.17 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) BOATING SAFETY VESSEL NUMBERING AND CASUALTY AND ACCIDENT REPORTING Numbering § 173.17 Reciprocity. (a) Section...

21 CFR 173.290 - Trichloroethylene.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Trichloroethylene. 173.290 Section 173.290 Food and..., Lubricants, Release Agents and Related Substances § 173.290 Trichloroethylene. Tolerances are established for residues of trichloroethylene resulting from its use as a solvent in the manufacture of foods as follows...

19 CFR 173.0 - Scope.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Scope. 173.0 Section 173.0 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY (CONTINUED) ADMINISTRATIVE REVIEW IN GENERAL § 173.0 Scope. This part deals with the general authority of review, the...

22 CFR 17.3 - Fault.

Science.gov (United States)

2010-04-01

... 22 Foreign Relations 1 2010-04-01 2010-04-01 false Fault. 17.3 Section 17.3 Foreign Relations...) § 17.3 Fault. A recipient of an overpayment is without fault if he or she performed no act of... agency may have been at fault in initiating an overpayment will not necessarily relieve the individual...

21 CFR 173.210 - Acetone.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Acetone. 173.210 Section 173.210 Food and Drugs..., Lubricants, Release Agents and Related Substances § 173.210 Acetone. A tolerance of 30 parts per million is established for acetone in spice oleoresins when present therein as a residue from the extraction of spice. ...

Studies on Optical and Electrical Properties of Hafnium Oxide Nanoparticles

Science.gov (United States)

Jayaraman, Venkatachalam; Sagadevan, Suresh; Sudhakar, Rajesh

2017-07-01

In this paper, the synthesis and physico-chemical properties of hafnium oxide nanoparticles (HfO2 NPs) are analyzed and reported. The synthesis was carried out by the precipitation route by using hafnium tetrachloride (HfCl4) as precursor material with potassium hydroxide (KOH) dissolved in Millipore water. In the precipitation technique, the chemical reaction is comparatively simple, low-cost and non-toxic compared to other synthetic methods. The synthesized HfO2 NPs were characterized by using powder x-ray diffraction (PXRD), ultraviolet-visible (UV-Vis) spectroscopy, Raman analysis, and high-resolution transmission electron microscopy (HRTEM). The monoclinic structure of the HfO2 NPs was resolved utilizing x-ray diffraction (XRD). The optical properties were studied from the UV-Vis absorption spectrum. The optical band gap of the HfO2NPs was observed to be 5.1 eV. The Raman spectrum shows the presence of HfO2 NPs. The HRTEM image showed that the HfO2 NPs were of spherical shape with an average particle size of around 28 nm. The energy-dispersive x-ray spectroscopy (EDS) spectrum obviously demonstrated the presence of HfO2 NPs. Analysis and studies on the dielectric properties of the HfO2 NPs such as the dielectric constant, the dielectric loss, and alternating current (AC) conductivity were carried out at varying frequencies and temperatures.

Rare-earth hafnium oxide materials for magnetohydrodynamic (MHD) generator application

Energy Technology Data Exchange (ETDEWEB)

Marchant, D. D; Bates, J. L.

1979-01-01

Several ceramic materials based on rare-earth hafnium oxides have been identified as potential high-temperature electrodes and low-temperature current leadouts for open cycle coal-fired MHD generator channels. The electrode-current leadouts combination must operate at temperatures between 400 and 2000K with an electrical conductivity greater than 10/sup -2/ ohm/sup -1/ cm/sup -1/. The electrodes will be exposed to flowing (linear flow rates up to 100 m/s) potassium seeded coal combustion gases (plasma core temperatures between 2400 to 3200/sup 0/K) and coal slag. During operation the electrodes must conduct direct electric current at densities near 1.5 amp/cm/sup 2/. Consequently, the electrodes must be resistant to electrochemical decompositions and interactions with both the coal slag and potassium salts (e.g., K/sub 2/SO/sub 4/, K/sub 2/CO/sub 3/). The current leadout materials are placed between the hot electrodes and the water-cooled copper structural members and must have electrical conductivities greater than 10/sup -2/ ohm/sup -1/ cm/sup -1/ between 1400 and 400/sup 0/K. The current leadouts must be thermally and electrochemically compatible with the electrode, copper, and potassium salts. Ideally, the electrodes and current leadouts should exhibit minimal ionic conductivity. The fabrication, electrical conductivity, and electrochemical corrosion of rare-earth hafnium oxide materials are discussed. (WHK)

Hafnium isotope evidence for a transition in the dynamics of continental growth 3.2 Gyr ago.

Science.gov (United States)

Næraa, T; Scherstén, A; Rosing, M T; Kemp, A I S; Hoffmann, J E; Kokfelt, T F; Whitehouse, M J

2012-05-30

Earth's lithosphere probably experienced an evolution towards the modern plate tectonic regime, owing to secular changes in mantle temperature. Radiogenic isotope variations are interpreted as evidence for the declining rates of continental crustal growth over time, with some estimates suggesting that over 70% of the present continental crustal reservoir was extracted by the end of the Archaean eon. Patterns of crustal growth and reworking in rocks younger than three billion years (Gyr) are thought to reflect the assembly and break-up of supercontinents by Wilson cycle processes and mark an important change in lithosphere dynamics. In southern West Greenland numerous studies have, however, argued for subduction settings and crust growth by arc accretion back to 3.8 Gyr ago, suggesting that modern-day tectonic regimes operated during the formation of the earliest crustal rock record. Here we report in situ uranium-lead, hafnium and oxygen isotope data from zircons of basement rocks in southern West Greenland across the critical time period during which modern-like tectonic regimes could have initiated. Our data show pronounced differences in the hafnium isotope-time patterns across this interval, requiring changes in the characteristics of the magmatic protolith. The observations suggest that 3.9-3.5-Gyr-old rocks differentiated from a >3.9-Gyr-old source reservoir with a chondritic to slightly depleted hafnium isotope composition. In contrast, rocks formed after 3.2 Gyr ago register the first additions of juvenile depleted material (that is, new mantle-derived crust) since 3.9 Gyr ago, and are characterized by striking shifts in hafnium isotope ratios similar to those shown by Phanerozoic subduction-related orogens. These data suggest a transitional period 3.5-3.2 Gyr ago from an ancient (3.9-3.5 Gyr old) crustal evolutionary regime unlike that of modern plate tectonics to a geodynamic setting after 3.2 Gyr ago that involved juvenile crust generation by plate

The interaction of fast neutrons with hafnium

International Nuclear Information System (INIS)

Smith, A.B.

2002-01-01

Elemental hafnium neutron total cross sections are measured from ∼0.75 to 4.5 MeV in steps of ∼40 keV. Differential neutron elastic-scattering cross sections are measured from ∼4.5 to 10.0 MeV in ∼0.5 MeV steps and at 40 scattering angles distributed between ∼17 and 160 deg. These data are combined with those found in the literature to construct a comprehensive experimental data base which is interpreted in terms of coupled-channels models. Physical characteristics of the resulting potentials are discussed. Comparisons are made with ENDF/B-6 (MAT 7200). A detailed report of this work is given by Smith (Smith, A., 2001. Argonne National Laboratory Report ANL/NDM-153)

Reinforcement against crack propagation of PWR absorbers by development of boron-carbon-hafnium composites

International Nuclear Information System (INIS)

Provot, B.; Herter, P.

2000-01-01

In order to improve the mechanical behaviour of materials used as neutron absorbers in nuclear reactors, we have developed CERCER or CERMET composites with boron and hafnium. Thus a new composite B 4 C/HfB 2 has been especially studied. We have identified three kinds of degradation under irradiation (thermal gradient, swelling due to fission products and accidental corrosion) that induce imposed deformations cracking phenomena. Mechanical behaviour and crack propagation resistance have been studied by ball-on-three-balls and double torsion tests. A special device was developed to enable crack propagation and associated stress intensity factor measurements. Effects of structure and of a second phase are underline. First results show that these materials present crack initiation and propagation resistance much higher than pure boron carbide or hafnium diboride. We observe R-Curves effects, crack bridging or branching, crack arrests, and toughness increases that we can relate respectively to the composite structures. (author)

Titrimetric determination of thiocyanate in solutions of the hafnium-zirconium separation process

International Nuclear Information System (INIS)

Vazquez, Cristina; Botbol, Moises; Hernandez, M.H.

1980-01-01

The control of the thiocyanate concentration is necessary during the process of separating hafnium from zirconium by the hexone-thiocyanate method. Said control is carried out by titrimetric determination of thiocyanate in aqueous and organic solutions containing hydrochloric acid and ammonium thiocyanate in presence or absence of zirconium and/or hafnium. The method consists in a redox volumetric analysis using a cerium (IV) salt as titrating agent, and ferroine as the final point indicator. Owing to the instability of thiocyanate in an acid medium it is necessary to know previously if the decomposition of solutions with different concentration of ammonium thiocyanate and hydrochloric acid may have an influence upon the analytic results or may even invalidate them. In order to obtain reliable results, it must be taken into account that the stability of the solutions depends on the thiocyanate concentration, the acidity and the time elapsed from the moment the sample is taken until the test is performed. The decomposition process can be slowed down by cooling the solutions. This method allows to control the plant and does not require any special equipment. (M.E.L) [es

49 CFR 173.173 - Paint, paint-related material, adhesives, ink and resins.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Paint, paint-related material, adhesives, ink and... Than Class 1 and Class 7 § 173.173 Paint, paint-related material, adhesives, ink and resins. (a) When..., paint-related material, adhesives, ink and resins must be packaged as follows: (1) As prescribed in...

Synthesis and characterization of hafnium oxide for luminescent applications

International Nuclear Information System (INIS)

Guzman Mendoza, J.; Aguilar Frutis, M.A.; Flores, G. Alarcon; Garcia Hipolito, M.; Azorin Nieto, J.; Rivera Montalvo, T.; Falcony, C.

2008-01-01

Full text: Hafnium oxide (HfO 2 ) is a material with a wide range of possible technological applications because it's chemical and physical properties such as high melting point, high chemical stability, high refraction index, high dielectric constant and hardness near to diamond in the tetragonal phase. The large energy gap and low phonon frequencies of the HfO 2 makes it appropriate as a host matrix for been doped with rare earth activators. Efficient luminescent materials find wide application in electroluminescent flat panel displays; color plasma displays panels, scintillators, cathode ray tubes, fluorescent lamps, lasers, etc. In recent years the study of luminescent materials based on HfO 2 has been intensified. Some groups have studied the optical properties of doped and undoped HfO 2 . In this contribution, Hafnium Oxide (HfO 2 ) films were prepared using the spray pyrolysis deposition technique. The material was synthesized using chlorides as raw materials in deionised water as solvent and deposited on Corning glass substrates at temperatures from 300 deg C to 600 deg C. For substrate temperatures lower than 400 deg C, the deposited films are amorphous, while for substrate temperatures higher than 450 deg C, the monoclinic phase of HfO 2 appears. Scanning electron microscopy with microprobe analysis was use to observe the microstructure and obtain the chemical composition of the films; rough surfaces with spherical particles were appreciated. UV and low energy X Ray radiations were used in order to achieve the thermoluminescent characterization of the films as a function of the deposition temperature

Titanium, zirconium- and hafnium containing initiators in the polymerization of acrylic monomers to ''living'' polymers

International Nuclear Information System (INIS)

Farnham, W.B.; Hertler, W.R.

1988-01-01

This patent describes a process for preparing ''living'' polymer. The process comprises contacting one or more acrylic monomers under polymerizing conditions with a polymerization-initiating amount of a tetra-coordinate organotitanium, organozirconium or organo-hafnium polymerization initiator, and ''living'' polymers produced thereby

Zirconium and hafnium tetrachloride separation by extractive distillation with molten zinc chloride lead chloride solvent

International Nuclear Information System (INIS)

McLaughlin, D.F.; Stoltz, R.A.

1988-01-01

In an extractive distillation method for separating hafniuim tetrachloride from zirconium tetrachloride of the type wherein a mixture of zirconium and hafnium tetrachlorides is introduced into an extractive distillation column, which extractive distillation column has a reboiler connected at the bottom and a reflux condenser connected at the top and wherein a molten salt solvent is circulated into the reflux condenser and through the column to provide a liquid phase, and wherein molten salt solvent containing zirconium tetrachloride is taken from the reboiler and run through a stripper to remove zirconium tetrachloride product from the molten salt solvent and the stripped molten salt solvent is returned to the reflux condenser and hafnium tetrachloride enriched vapor is taken as product from the reflux condenser, the improvement is described comprising: the molten salt having a composition of at least 30 mole percent zinc chloride and at least 10 mole percent of lead chloride

Atomic layer deposition of calcium oxide and calcium hafnium oxide films using calcium cyclopentadienyl precursor

International Nuclear Information System (INIS)

Kukli, Kaupo; Ritala, Mikko; Sajavaara, Timo; Haenninen, Timo; Leskelae, Markku

2006-01-01

Calcium oxide and calcium hafnium oxide thin films were grown by atomic layer deposition on borosilicate glass and silicon substrates in the temperature range of 205-300 o C. The calcium oxide films were grown from novel calcium cyclopentadienyl precursor and water. Calcium oxide films possessed refractive index 1.75-1.80. Calcium oxide films grown without Al 2 O 3 capping layer occurred hygroscopic and converted to Ca(OH) 2 after exposure to air. As-deposited CaO films were (200)-oriented. CaO covered with Al 2 O 3 capping layers contained relatively low amounts of hydrogen and re-oriented into (111) direction upon annealing at 900 o C. In order to examine the application of CaO in high-permittivity dielectric layers, mixtures of Ca and Hf oxides were grown by alternate CaO and HfO 2 growth cycles at 230 and 300 o C. HfCl 4 was used as a hafnium precursor. When grown at 230 o C, the films were amorphous with equal amounts of Ca and Hf constituents (15 at.%). These films crystallized upon annealing at 750 o C, showing X-ray diffraction peaks characteristic of hafnium-rich phases such as Ca 2 Hf 7 O 16 or Ca 6 Hf 19 O 44 . At 300 o C, the relative Ca content remained below 8 at.%. The crystallized phase well matched with rhombohedral Ca 2 Hf 7 O 16 . The dielectric films grown on Si(100) substrates possessed effective permittivity values in the range of 12.8-14.2

49 CFR 173.322 - Ethyl chloride.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Ethyl chloride. 173.322 Section 173.322 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.322 Ethyl chloride. Ethyl chloride must be...

49 CFR 173.443 - Contamination control.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Contamination control. 173.443 Section 173.443... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.443 Contamination control. (a) The level of non-fixed (removable) radioactive contamination on the external surfaces of each package offered for...

Separation of zirconium--hafnium by nitride precipitation

International Nuclear Information System (INIS)

Anderson, R.N.; Parlee, N.A.

1977-01-01

A method is described for the separation of a light reactive metal (e.g., zirconium) from a heavy reactive metal (e.g., hafnium) by forming insoluble nitrides of the metals in a molten metal solvent (e.g., copper) inert to nitrogen and having a suitable density for the light metal nitride to form a separate phase in the upper portion of the solvent and for the heavy metal nitride to form a separate phase in the lower portion of the solvent. Nitriding is performed by maintaining a nitrogen-containing atmosphere over the bath. The light and heavy metals may be an oxide mixture and carbothermically reduced to metal form in the same bath used for nitriding. The nitrides are then separately removed and decomposed to form the desired separate metals. 16 claims, 1 figure

21 CFR 173.160 - Candida guilliermondii.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Candida guilliermondii. 173.160 Section 173.160... CONSUMPTION Enzyme Preparations and Microorganisms § 173.160 Candida guilliermondii. The food additive Candida... the following conditions: (a) The food additive is the enzyme system of the viable organism Candida...

Modified method for zirconium or hafnium gravimetric determination with glycolic acid derivatives

International Nuclear Information System (INIS)

Barbieri, R.S.; Rocha, J.C.; Terra, V.R.; Marques Neto, A.

1989-01-01

The conditions for gravimetric determination of zirconium or hafnium by glicolic acid derivatives were studied by thermogravimetric analysis. The method utilized shown that after precipitation, washing and drying of precipitates at 150 0 C, the resulting solid was weighed in the form of [M{RCH(OH)COO} 4 ] (M = Zr,Hf;R = C 6 H 5 , β-C 10 H 7 ,p-BrC 6 H 4 ). (author) [pt

Correlations between nuclear data and integral slab experiments: the case of hafnium; Correlations entre donnees nucleaires et experiences integrales a plaques: le cas du hafnium

Energy Technology Data Exchange (ETDEWEB)

Palau, J M

1999-07-01

The aim of this work was to evaluate how much integral slab experiments can both reduce discrepancies between experimental results and calculations, and improve the knowledge of hafnium isotopes neutronic parameters by an adapted sensitivity and uncertainty method. A statistical approach, based on the generalized least squares method and perturbation theory, has been incorporated into our calculation system in order to deduce microscopic cross-section adjustments from observed integral measurements on this particular 'mock-up' reactor.In this study it has been established that the correlations between integral parameters and hafnium capture cross-sections enable specific variations in the region of resolved resonances at the level of multigroup and punctual cross-sections recommended data (JEF-2.2 evaluation) to be highlighted. The use of determinist methods together with Monte Carlo- type simulations enabled a depth analysis of the modelling approximations to be carried out. Furthermore, the sensitivity coefficient validation technique employed leads to a reliable assessment of the quality of the new basic nuclear data. In this instance, the adjustments proposed for certain isotope {sup 177}Hf resonance parameters reduce, after error propagation, by 3 to 5 per cent the difference between experimental results and calculations related to this absorbent's efficiency. Beyond this particular application, the qualification methodology integrated in our calculation system should enable other basic sizing parameters to be treated (chemical / geometric data or other unexplored nuclear data) to make technological requirements less stringent. (author)

Correlations between nuclear data and integral slab experiments: the case of hafnium; Correlations entre donnees nucleaires et experiences integrales a plaques: le cas du hafnium

Energy Technology Data Exchange (ETDEWEB)

Palau, J.M

1999-07-01

The aim of this work was to evaluate how much integral slab experiments can both reduce discrepancies between experimental results and calculations, and improve the knowledge of hafnium isotopes neutronic parameters by an adapted sensitivity and uncertainty method. A statistical approach, based on the generalized least squares method and perturbation theory, has been incorporated into our calculation system in order to deduce microscopic cross-section adjustments from observed integral measurements on this particular 'mock-up' reactor.In this study it has been established that the correlations between integral parameters and hafnium capture cross-sections enable specific variations in the region of resolved resonances at the level of multigroup and punctual cross-sections recommended data (JEF-2.2 evaluation) to be highlighted. The use of determinist methods together with Monte Carlo- type simulations enabled a depth analysis of the modelling approximations to be carried out. Furthermore, the sensitivity coefficient validation technique employed leads to a reliable assessment of the quality of the new basic nuclear data. In this instance, the adjustments proposed for certain isotope {sup 177}Hf resonance parameters reduce, after error propagation, by 3 to 5 per cent the difference between experimental results and calculations related to this absorbent's efficiency. Beyond this particular application, the qualification methodology integrated in our calculation system should enable other basic sizing parameters to be treated (chemical / geometric data or other unexplored nuclear data) to make technological requirements less stringent. (author)

On-line separation of refractory hafnium and tantalum isotopes at the ISOCELE separator

CERN Document Server

Liang, C F; Obert, J; Paris, P; Putaux, J C

1981-01-01

By chemical evaporation technique, neutron deficient hafnium nuclei have been on-line separated at the ISOCELE facility, from the isobar rare-earth elements, in the metal-fluoride HfF/sub 3//sup +/ ion form. Half-lives of /sup 162-165/Hf have been measured. Similarly, tantalum has been selectively separated on the TaF/sub 4//sup +/ form. (4 refs) .

21 CFR 173.230 - Ethylene dichloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Ethylene dichloride. 173.230 Section 173.230 Food... Solvents, Lubricants, Release Agents and Related Substances § 173.230 Ethylene dichloride. A tolerance of 30 parts per million is established for ethylene dichloride in spice oleoresins when present therein...

21 CFR 173.255 - Methylene chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methylene chloride. 173.255 Section 173.255 Food... Solvents, Lubricants, Release Agents and Related Substances § 173.255 Methylene chloride. Methylene chloride may be present in food under the following conditions: (a) In spice oleoresins as a residue from...

21 CFR 173.375 - Cetylpyridinium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Cetylpyridinium chloride. 173.375 Section 173.375... CONSUMPTION Specific Usage Additives § 173.375 Cetylpyridinium chloride. Cetylpyridinium chloride (CAS Reg. No....1666 of this chapter, at a concentration of 1.5 times that of cetylpyridinium chloride. (c) The...

Self-cleaning and surface chemical reactions during hafnium dioxide atomic layer deposition on indium arsenide.

Science.gov (United States)

Timm, Rainer; Head, Ashley R; Yngman, Sofie; Knutsson, Johan V; Hjort, Martin; McKibbin, Sarah R; Troian, Andrea; Persson, Olof; Urpelainen, Samuli; Knudsen, Jan; Schnadt, Joachim; Mikkelsen, Anders

2018-04-12

Atomic layer deposition (ALD) enables the ultrathin high-quality oxide layers that are central to all modern metal-oxide-semiconductor circuits. Crucial to achieving superior device performance are the chemical reactions during the first deposition cycle, which could ultimately result in atomic-scale perfection of the semiconductor-oxide interface. Here, we directly observe the chemical reactions at the surface during the first cycle of hafnium dioxide deposition on indium arsenide under realistic synthesis conditions using photoelectron spectroscopy. We find that the widely used ligand exchange model of the ALD process for the removal of native oxide on the semiconductor and the simultaneous formation of the first hafnium dioxide layer must be significantly revised. Our study provides substantial evidence that the efficiency of the self-cleaning process and the quality of the resulting semiconductor-oxide interface can be controlled by the molecular adsorption process of the ALD precursors, rather than the subsequent oxide formation.

12 CFR 308.173 - Prevailing party.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 4 2010-01-01 2010-01-01 false Prevailing party. 308.173 Section 308.173 Banks....173 Prevailing party. (a) General rule. An eligible applicant who, following an adversary adjudication has gained victory on the merits in the proceeding is a “prevailing party”. An eligible applicant may...

49 CFR 173.323 - Ethylene oxide.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Ethylene oxide. 173.323 Section 173.323... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.323 Ethylene oxide. (a) For packaging ethylene oxide in non-bulk packagings, silver mercury or any of its alloys or copper may not be used in any...

Ground-state structures of Hafnium clusters

Energy Technology Data Exchange (ETDEWEB)

Ng, Wei Chun; Yoon, Tiem Leong [School of Physics, Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Lim, Thong Leng [Faculty of Engineering and Technoloty, Multimedia University, Melaca Campus, 75450 Melaka (Malaysia)

2015-04-24

Hafnium (Hf) is a very large tetra-valence d-block element which is able to form relatively long covalent bond. Researchers are interested to search for substitution to silicon in the semi-conductor industry. We attempt to obtain the ground-state structures of small Hf clusters at both empirical and density-functional theory (DFT) levels. For calculations at the empirical level, charge-optimized many-body functional potential (COMB) is used. The lowest-energy structures are obtained via a novel global-minimum search algorithm known as parallel tempering Monte-Carlo Basin-Hopping and Genetic Algorithm (PTMBHGA). The virtue of using COMB potential for Hf cluster calculation lies in the fact that by including the charge optimization at the valence shells, we can encourage the formation of proper bond hybridization, and thus getting the correct bond order. The obtained structures are further optimized using DFT to ensure a close proximity to the ground-state.

Molecular structure, vibrational, HOMO-LUMO, MEP and NBO analysis of hafnium selenite

Science.gov (United States)

Yankova, Rumyana; Genieva, Svetlana; Dimitrova, Ginka

2017-08-01

In hydrothermal condition hafnium selenite with estimated chemical composition Hf(SeO3)2·n(H2O) was obtained and characterized by powder X-Ray diffraction, IR spectroscopy and thermogravimetrical analysis. The composition of the obtained crystalline phase was established as dihydrate of tetraaqua complex of the hafnium selenite [Hf(SeO3)2(H2O)4]·2H2O. The results of the thermogravimetrical analysis are shown that the two hydrated water molecules are released in the temperature interval 80-110°C, while the four coordinated water molecules - at 210-300°C. By DFT method, with Becke's three parameter exchange-functional combined with gradient-corrected correlation functional of Lee, Yang and Parr and 6-31G(d), 6-311 + G(d,p) basis sets and LANL2DZ for Hf atom were calculated the molecular structure, vibrational frequencies and thermodynamic properties of the structure. The UV-Vis spectra and electronic properties are presented. The energy and oscillator strength calculated by time-dependent density functional theory corresponds well with the experimental ones. Molecular electrostatic potential (MEP) was performed. Mulliken population analysis on atomic charges was also calculated. The stability and intramolecular interactions are interpreted by NBO analysis.

Near net shape processing of zirconium or hafnium metals and alloys

International Nuclear Information System (INIS)

Evans, S.C.

1992-01-01

This patent describes a process for producing a metal shape. It comprises: plasma arc melting a metal selected from zirconium, hafnium and alloys thereof comprising at least about 90 w/o of these metals to form a liquid pool; pouring the metal form the pool into a mold to form a near net shape; and reducing the metal from its near net shape to a final size while maintaining the metal temperature below the alpha-beta transition temperature throughout the size reducing step

In-Pile Experiment of a New Hafnium Aluminide Composite Material to Enable Fast Neutron Testing in the Advanced Test Reactor

Energy Technology Data Exchange (ETDEWEB)

Donna Post Guillen; Douglas L. Porter; James R. Parry; Heng Ban

2010-06-01

A new hafnium aluminide composite material is being developed as a key component in a Boosted Fast Flux Loop (BFFL) system designed to provide fast neutron flux test capability in the Advanced Test Reactor. An absorber block comprised of hafnium aluminide (Al3Hf) particles (~23% by volume) dispersed in an aluminum matrix can absorb thermal neutrons and transfer heat from the experiment to pressurized water cooling channels. However, the thermophysical properties, such as thermal conductivity, of this material and the effect of irradiation are not known. This paper describes the design of an in-pile experiment to obtain such data to enable design and optimization of the BFFL neutron filter.

Complexing of zirconium and hafnium with ortho-aminobenzoic acid and paraaminobenzoic acid

International Nuclear Information System (INIS)

Alekseeva, I.I.; Nemzer, I.I.; Yuranova, L.I.; Borisova, V.V.; Prozorovskaya, Z.N.

1977-01-01

Formation of complexes between zirconium and hafnium and ortho- and para-aminobenzoic acids has been studied by the kinetic method. It has been found that at pH=1.3-2.0 and concentrations of metals 10 -5 -10 -6 mole complex compounds are formed with composition Me:L=1:2 and 1:1 (Me=Zr, Hf; L=ortho- or para-aminobenzoic acids). Stepwise constants and overall effective constants of complex formation have been calculated

Correlations between nuclear data and results of integral slab experiments. Case of hafnium; Correlations entre donnees nucleaires et experiences integrales a plaques: le cas du hafnium

Energy Technology Data Exchange (ETDEWEB)

Palau, J M

1997-10-22

The aim of this thesis was to evaluate how much integral slab experiments can both reduce discrepancies between experimental results and calculations, and improve the knowledge of hafnium isotopes neutronic parameters by an adapted sensitivity and uncertainty method. A statistical approach, based on the generalized least squares method and perturbation theory, has been incorporated into our calculation system in order to deduce microscopic cross-section adjustments from observed integral measurements on this particular `mock-up` reactor. In this study it has been established that the correlations between integral parameters and hafnium capture cross-sections enable specific variations in the region of resolved resonances at the level of multigroup and punctual cross-sections recommended data (JEF-2.2 evaluation) to be highlighted. The use of determinist methods (APOLLO2 code) together with Monte Carlo- type simulations (TRIPOLI4 code) enabled a depth analysis of the modelling approximations to be carried out. Furthermore, the sensitivity coefficient validation technique employed leads to a reliable assessment of the quality of the new basic nuclear data. In this instance, the adjustments proposed for certain isotope {sup 177}Hf resonance parameters reduce, after error propagation, by 3 to 5 per cent the difference between experimental results and calculations related to this absorbent`s efficiency. Beyond this particular application, the qualification methodology integrated in our calculation system should enable other basic sizing parameters to be treated (chemical / geometric data or other unexplored nuclear data) to make technological requirements less stringent. (author) 128 refs.

46 CFR 173.010 - Definitions.

Science.gov (United States)

2010-10-01

... VESSEL USE Lifting § 173.010 Definitions. As used in this part— (a) Hook load means the weight of the object lifted by the crane. (b) Crane radius means the distance illustrated in Figure 173.010. EC01MR91...

High temperature thermodynamics of solutions of oxygen in zirconium and hafnium

International Nuclear Information System (INIS)

Boureau, G.; Gerdanian, P.

1984-01-01

The Tian-Calvet microcalorimetric method has been applied to the determination at 1323 Kelvin of ΔH(O 2 ), the partial molar enthalpy of mixing of oxygen in zirconium and in hafnium. No measurable departure from Henry's law has been found for dilute solutions (ratio oxygen over metal smaller than 0.1). For concentrated solutions repulsive interactions are found in agreement with the existence of ordered structures at lower temperatures. The domain of homogeneity of zirconium has been found larger than previously assumed. (author)

Extraction of hafnium by 1-phenyl-3-methyl-4-benzoyl-5-pyralozone from aqueous-alcoholic solutions

International Nuclear Information System (INIS)

Hala, J.; Prihoda, J.

1975-01-01

Extraction of hafnium by 1-phenyl-3-methyl-4-benzoyl-5-pyrazolone (HL) in benzene, toluene, chloroform and tetrachloromethane from aqueous-alcoholic solutions of the formal acidity of 2M-HClO 4 was studied. Methyl, ethyl, n- and isopropyl, tert-butyl and allyl alcohol as well as ethylene glycol monomethyl ether and propylene glycol were used as organic components of the mixed aqueous-organic phase. Their presence in some cases resulted in a synergic increase in the distribution ratio of hafnium. The increase is interpreted using the results of a slope analysis and measurements of the alcohol distribution and the relative permittivity of the organic phase. It is suggested that HfL 4 molecules were solvated by alcohol molecules in the organic phase. At high alcohol concentration synergism changed into antagonism. This was caused by changes in the distribution of HL and its interaction with the alcohol in the organic phase. (author)

34 CFR 668.173 - Refund reserve standards.

Science.gov (United States)

2010-07-01

... 34 Education 3 2010-07-01 2010-07-01 false Refund reserve standards. 668.173 Section 668.173 Education Regulations of the Offices of the Department of Education (Continued) OFFICE OF POSTSECONDARY EDUCATION, DEPARTMENT OF EDUCATION STUDENT ASSISTANCE GENERAL PROVISIONS Financial Responsibility § 668.173...

Trap state passivation improved hot-carrier instability by zirconium-doping in hafnium oxide in a nanoscale n-metal-oxide semiconductor-field effect transistors with high-k/metal gate

International Nuclear Information System (INIS)

Liu, Hsi-Wen; Tsai, Jyun-Yu; Liu, Kuan-Ju; Lu, Ying-Hsin; Chang, Ting-Chang; Chen, Ching-En; Tseng, Tseung-Yuen; Lin, Chien-Yu; Cheng, Osbert; Huang, Cheng-Tung; Ye, Yi-Han

2016-01-01

This work investigates the effect on hot carrier degradation (HCD) of doping zirconium into the hafnium oxide high-k layer in the nanoscale high-k/metal gate n-channel metal-oxide-semiconductor field-effect-transistors. Previous n-metal-oxide semiconductor-field effect transistor studies demonstrated that zirconium-doped hafnium oxide reduces charge trapping and improves positive bias temperature instability. In this work, a clear reduction in HCD is observed with zirconium-doped hafnium oxide because channel hot electron (CHE) trapping in pre-existing high-k bulk defects is the main degradation mechanism. However, this reduced HCD became ineffective at ultra-low temperature, since CHE traps in the deeper bulk defects at ultra-low temperature, while zirconium-doping only passivates shallow bulk defects.

Determination of hafnium with the inductively coupled plasma (ICP)

International Nuclear Information System (INIS)

Wuensch, G.; Pose, K.

1985-01-01

The relative intensities of 198 hafnium lines in the Ar-ICP are listed. Spectral interference tables are given for the 9 analytically best lines, covering the range of +-60 pm around the Hf-lines. They include measured (not calculated) data of the interferent equivalent concentrations (IEC) and the critical concentration ratios (CCR) for 115 lines of all 34 possibly interfering elements. In many cases, these IEC- or CCR-data differ by 1 or 2 orders of magnitude from those calculated from intensities observed in the NBS-copper arc. Since no intense Hf-line is free from spectral interferences, examples are given for the calculation of the most suitable line for a known matrix. (orig.) [de

21 CFR 173.355 - Dichlorodifluoromethane.

Science.gov (United States)

2010-04-01

... with good manufacturing practice, as a direct-contact freezing agent for foods. (c) To assure safe use... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Dichlorodifluoromethane. 173.355 Section 173.355 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD...

29 CFR 1915.173 - Drums and containers.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Drums and containers. 1915.173 Section 1915.173 Labor... Vessels, Drums and Containers, Other Than Ship's Equipment § 1915.173 Drums and containers. (a) Shipping drums and containers shall not be pressurized to remove their contents. (b) A temporarily assembled...

49 CFR 173.3 - Packaging and exceptions.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Packaging and exceptions. 173.3 Section 173.3... SHIPMENTS AND PACKAGINGS General § 173.3 Packaging and exceptions. (a) The packaging of hazardous materials.... standard packaging must be open to inspection by a representative of the Department. (b) The regulations...

13 CFR 120.173 - Lead-based paint.

Science.gov (United States)

2010-01-01

... 13 Business Credit and Assistance 1 2010-01-01 2010-01-01 false Lead-based paint. 120.173 Section 120.173 Business Credit and Assistance SMALL BUSINESS ADMINISTRATION BUSINESS LOANS Policies Applying to All Business Loans Requirements Imposed Under Other Laws and Orders § 120.173 Lead-based paint. If...

21 CFR 173.275 - Hydrogenated sperm oil.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Hydrogenated sperm oil. 173.275 Section 173.275... CONSUMPTION Solvents, Lubricants, Release Agents and Related Substances § 173.275 Hydrogenated sperm oil. The food additive hydrogenated sperm oil may be safely used in accordance with the following prescribed...

25 CFR 173.2 - Project engineer's authority.

Science.gov (United States)

2010-04-01

... 25 Indians 1 2010-04-01 2010-04-01 false Project engineer's authority. 173.2 Section 173.2 Indians... LANDS WITHDRAWN OR ACQUIRED IN CONNECTION WITH INDIAN IRRIGATION PROJECTS § 173.2 Project engineer's authority. The project engineer is the official charged with the responsibility for the enforcement of this...

49 CFR 173.183 - Nitrocellulose base film.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Nitrocellulose base film. 173.183 Section 173.183... Nitrocellulose base film. Films, nitrocellulose base, must be packaged in packagings conforming to the... tape or paper; authorized only for not over 600 m (1969 feet) of film. [Amdt. 173-224, 55 FR 52643 Dec...

21 CFR 173.55 - Polyvinylpyrrolidone.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyvinylpyrrolidone. 173.55 Section 173.55 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR... a residual level not to exceed 40 parts per million. Wine As a clarifying agent, at a residual level...

Atom-vacancy ordering and magnetic susceptibility of nonstoichiometric hafnium carbide

International Nuclear Information System (INIS)

Gusev, A.I.; Zyryanova, A.N.

1999-01-01

Experimental results on magnetic susceptibility of nonstoichiometric hafnium carbide HfC y (0.6 0.71 , HfC 0.78 and HfC 0.83 in the range of 870-930 K the anomalies are revealed which are associated with superstructure short-range ordering in a non-metallics sublattice. It is shown that a short-range order in HfC 0.71 and HfC 0.78 carbides corresponds to Hf 3 C 2 ordered phase, and in HfC 0.83 carbide - to Hf 6 C 5 ordered phase. HfC 0.78 carbide is found to possesses zero magnetic susceptibility in temperature range 910-980 K [ru

Hafnium carbide nanocrystal chains for field emitters

International Nuclear Information System (INIS)

Tian, Song; Li, Hejun; Zhang, Yulei; Ren, Jincui; Qiang, Xinfa; Zhang, Shouyang

2014-01-01

A hafnium carbide (HfC) nanostructure, i.e., HfC nanocrystal chain, was synthesized by a chemical vapor deposition (CVD) method. X-ray diffractometer, field-emission scanning electron microscope, transmission electron microscope, and energy-dispersive X-ray spectrometer were employed to characterize the product. The synthesized one-dimensional (1D) nanostructures with many faceted octahedral nanocrystals possess diameters of tens of nanometers to 500 nm and lengths of a few microns. The chain-like structures possess a single crystalline structure and preferential growth direction along the [1 0 0] crystal orientation. The growth of the chains occurred through the vapor–liquid–solid process along with a negative-feedback mechanism. The field emission (FE) properties of the HfC nanocrystal chains as the cold cathode emitters were examined. The HfC nanocrystal chains display good FE properties with a low turn-on field of about 3.9 V μm −1 and a high field enhancement factor of 2157, implying potential applications in vacuum microelectronics.

Simplified method for gravimetric determination of zirconium or hafnium with α-hydroxy carboxylic acids

International Nuclear Information System (INIS)

Barbieri, R.S.; Rocha, J.C.; Terra, V.R.; Marques Netto, A.

1989-01-01

The conditions for gravimetric determination of zirconium or hafnium by glicoloc acids derivatives were studied by thermogravimetric analysis. The method utilized shownd that after precipitation, washing and drying of precipitates at 150 o C, the resulting solid was weighed in the form of [M (RCH(OH)COO) 4 ] (M = Zr, Hf; R + C 6 H 5 , β-C 10 H 7 , p-BrC 6 H 4 ). (author)

Complexonometric determination of hafnium (4) in the presence of europium(3) or tantalum(5)

International Nuclear Information System (INIS)

Oziashvili, E.D.; Ehsakiya, K.E.; Sirakanyan, N.M.

1986-01-01

Complexonometric determination of hafnium in the presence of Ta or Eu in samples which can be decomposed by acids, i.e. in double borides has been investigated. Initial solutions are prepared by fusing with K 2 S 2 O 8 excess, the fusion was leached by hot water, H 2 SO L 4 was added and Hf was titrated by complexone 3 in the presence of xylenol orange

Investigation of interaction of zirconium and hafnium tetrafluorides with strontium fluoride

International Nuclear Information System (INIS)

Ratnikova, I.D.; Korenev, Yu.M.; Novoselova, A.V.

1980-01-01

Diagrams of the condensated state of systems SrF 2 -EF 4 have been plotted, where E represents Zr, Hf. In these systems, three intermediate compounds of Sr 3 EF 10 , Sr 2 EF 8 and Sr EF 6 compositions are formed. All those compounds melt incongruently at temperatures of 982, 865 and 750 deg C, respectively - zirconium salt; at temperatures of 1000, 900 and 820 deg C - hafnium salts. Fluoro-metallates of composition 2:1, and 1:1, exist in two polymorphic forms. Tetrafluorides were found to dissolve in strontium fluoride: they form solid solutions having fluorite structure

Correlations between nuclear data and integral slab experiments: the case of hafnium

International Nuclear Information System (INIS)

Palau, J.M.

1999-01-01

The aim of this work was to evaluate how much integral slab experiments can both reduce discrepancies between experimental results and calculations, and improve the knowledge of hafnium isotopes neutronic parameters by an adapted sensitivity and uncertainty method. A statistical approach, based on the generalized least squares method and perturbation theory, has been incorporated into our calculation system in order to deduce microscopic cross-section adjustments from observed integral measurements on this particular 'mock-up' reactor.In this study it has been established that the correlations between integral parameters and hafnium capture cross-sections enable specific variations in the region of resolved resonances at the level of multigroup and punctual cross-sections recommended data (JEF-2.2 evaluation) to be highlighted. The use of determinist methods together with Monte Carlo- type simulations enabled a depth analysis of the modelling approximations to be carried out. Furthermore, the sensitivity coefficient validation technique employed leads to a reliable assessment of the quality of the new basic nuclear data. In this instance, the adjustments proposed for certain isotope 177 Hf resonance parameters reduce, after error propagation, by 3 to 5 per cent the difference between experimental results and calculations related to this absorbent's efficiency. Beyond this particular application, the qualification methodology integrated in our calculation system should enable other basic sizing parameters to be treated (chemical / geometric data or other unexplored nuclear data) to make technological requirements less stringent. (author)

21 CFR 173.400 - Dimethyldialkylammonium chloride.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Dimethyldialkylammonium chloride. 173.400 Section... HUMAN CONSUMPTION Specific Usage Additives § 173.400 Dimethyldialkylammonium chloride. Dimethyldialkylammonium chloride may be safely used in food in accordance with the following prescribed conditions: (a...

Laser coating of hafnium on Ti6Al4 for biomedical applications

CSIR Research Space (South Africa)

Phume, L

2012-12-01

Full Text Available Al4V FOR BIOMEDICAL APPLICATIONS Lerato Phume 1, 2, S.L. Pityana 1, 2, C. Meacock 1, A.P.I Popoola 2 1. National Laser Centre, Council for Scientific and Industrial Research, P.O. Box 395, Pretoria, 0001, South Africa 2. Department of Chemical... and Metallurgical Engineering, Tshwane University of Technology, Private Bag X 680, Pretoria, 0001, South Africa (b) (c) (e) To investigate laser surface coating of Ti6Al4V with preplaced Hafnium powder, to determine the influence of the energy density...

Preparation, structure and properties of hafnium compounds in the system Hf-C-N-O

International Nuclear Information System (INIS)

Brundiers, G.D.

1975-08-01

Highly dense, homogenous and single phase hafnium carbonitride samples (with low oxygen content) were prepared in the whole concentration range of the ternary cubic carbonitrides. Stoichiometric hafnium oxicarbides were also prepared within the range of solubility. The procedure involved the hot pressing of powders of HfC, HfN, Hf, Hf-Oxide and carbon at temperatures of 3,000 0 C and pressures up to 550 kpf/cm 2 using a novel technique. Small single crystals of slightly substoichiometric HfN were also repared. The densification of the powders was studied as a function of the non-metal concentration. Carbonitrides with N/Hf ratio of 0.37 were prepared in a high temperature autoclave operating at medium pressures by the reaction of HfC with nitrogen. All the samples were characterized by density measurements, chemical, X-ray and metallographic analysis and in some cases with the aid of quantitative metallography and microprobe analysis. Typical properties investigated were lattice parameter, thermal expansion, microhardness and electrical resistivity as function of the non-metal content. For specific concentrations extreme values in the properties are attained. With the aid of the valence electron concentration (VEC) parameter, the properties can be correlated with the density of states of electrons at the Fermi level. (orig./HK) [de

7 CFR 1150.173 - Confidential treatment.

Science.gov (United States)

2010-01-01

... reports of the number of persons subject to this subpart or statistical data collected therefrom, which... 7 Agriculture 9 2010-01-01 2009-01-01 true Confidential treatment. 1150.173 Section 1150.173 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Marketing...

49 CFR 173.174 - Refrigerating machines.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Refrigerating machines. 173.174 Section 173.174 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... Refrigerating machines. A refrigerating machine assembled for shipment and containing 7 kg (15 pounds) or less...

49 CFR 173.465 - Type A packaging tests.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Type A packaging tests. 173.465 Section 173.465 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS MATERIALS SAFETY... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.465 Type A packaging tests. (a) The packaging...

Systematic investigation of electromagnetic properties of all stable hafnium isotopes

International Nuclear Information System (INIS)

Napiorkowski, T.J.; Choinski, J.; Czosnyka, T.; Iwanicki, J.; Kownacki, J.; Zemlo, L.; Srebrny, J.; Starosta, K.; Boer, J. de.; Gollwitzer, A.; Loewe, M.; Wuerkner, M.; Guenther, C.; Weber, T.; Hagemann, G.; Sletten, G.

1996-01-01

In a systematic investigation of the electromagnetic structure of hafnium stable isotopes enriched targets of 176, 177, 178, 179, 180 Hf were Coulomb exciting using: 67 MeV 19 F beam from NBITAL FN Tandem, 125 MeV 32 S beam from MP Tandem in Accelerator Laboratory LMU and TU Munich, 225 MeV 58 Ni beam from NBITAL FN Tandem plus 2 Liniac Boosters complex. Scattered particle-gamma as well as p-γ-γ coincidence were registered. A further simultaneous analysis of Coulomb excitation cross section as a function of scattering angle of 19 F, 32 S, 58 Ni projectiles should be sufficient to deduce reduced probabilities of E2 transitions in ground state band

40 CFR 173.9 - Judicial review.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Judicial review. 173.9 Section 173.9 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) PESTICIDE PROGRAMS PROCEDURES GOVERNING... Judicial review. The State may appeal an order rescinding, in whole or in part, its primary enforcement...

49 CFR 173.159 - Batteries, wet.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Batteries, wet. 173.159 Section 173.159... Batteries, wet. (a) Electric storage batteries, containing electrolyte acid or alkaline corrosive battery fluid (wet batteries), may not be packed with other materials except as provided in paragraphs (g) and...

46 CFR 173.051 - Public nautical school ships.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Public nautical school ships. 173.051 Section 173.051 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY SPECIAL RULES PERTAINING TO VESSEL USE School Ships § 173.051 Public nautical school ships. Each public nautical school...

46 CFR 173.062 - Drainage of weather deck.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Drainage of weather deck. 173.062 Section 173.062 Shipping COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) SUBDIVISION AND STABILITY SPECIAL RULES PERTAINING TO VESSEL USE School Ships § 173.062 Drainage of weather deck. The weather deck of each sailing...

21 CFR 211.173 - Laboratory animals.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 4 2010-04-01 2010-04-01 false Laboratory animals. 211.173 Section 211.173 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) DRUGS... Laboratory animals. Animals used in testing components, in-process materials, or drug products for compliance...

21 CFR 173.240 - Isopropyl alcohol.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Isopropyl alcohol. 173.240 Section 173.240 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) SECONDARY DIRECT FOOD ADDITIVES PERMITTED IN FOOD FOR HUMAN CONSUMPTION Solvents...

49 CFR 173.163 - Hydrogen fluoride.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrogen fluoride. 173.163 Section 173.163... Hydrogen fluoride. (a) Hydrogen fluoride (hydrofluoric acid, anhydrous) must be packaged as follows: (1) In... filling ratio of 0.84. (b) A cylinder removed from hydrogen fluoride service must be condemned in...

Highly substituted zirconium and hafnium cyclopentadienyl bifunctional β-diketiminate complexes – Synthesis, structure, and catalytic activity towards ethylene polymerization

Czech Academy of Sciences Publication Activity Database

Havlík, A.; Lamač, Martin; Pinkas, Jiří; Varga, Vojtěch; Růžička, A.; Olejník, R.; Horáček, Michal

2015-01-01

Roč. 786, JUN 2015 (2015), s. 71-80 ISSN 0022-328X R&D Projects: GA ČR GAP106/10/0924 Institutional support: RVO:61388955 Keywords : Zirconium * Hafnium * Cyclopentadienyl Subject RIV: CF - Physical ; Theoretical Chemistry Impact factor: 2.336, year: 2015

49 CFR 173.31 - Use of tank cars.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Use of tank cars. 173.31 Section 173.31... SHIPMENTS AND PACKAGINGS Preparation of Hazardous Materials for Transportation § 173.31 Use of tank cars. (a) General. (1) No person may offer a hazardous material for transportation in a tank car unless the tank car...

Wake-up effects in Si-doped hafnium oxide ferroelectric thin films

International Nuclear Information System (INIS)

Zhou, Dayu; Xu, Jin; Li, Qing; Guan, Yan; Cao, Fei; Dong, Xianlin; Müller, Johannes; Schenk, Tony; Schröder, Uwe

2013-01-01

Hafnium oxide based ferroelectric thin films have shown potential as a promising alternative material for non-volatile memory applications. This work reports the switching stability of a Si-doped HfO 2 film under bipolar pulsed-field operation. High field cycling causes a “wake-up” in virgin “pinched” polarization hysteresis loops, demonstrated by an enhancement in remanent polarization and a shift of negative coercive voltage. The rate of wake-up is accelerated by either reducing the frequency or increasing the amplitude of the cycling field. We suggest de-pinning of domains due to reduction of the defect concentration at bottom electrode interface as origin of the wake-up

49 CFR 173.185 - Lithium cells and batteries.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Lithium cells and batteries. 173.185 Section 173... Class 7 § 173.185 Lithium cells and batteries. (a) Cells and batteries. A lithium cell or battery, including a lithium polymer cell or battery and a lithium-ion cell or battery, must conform to all of the...

Correlations between nuclear data and results of integral slab experiments. Case of hafnium

International Nuclear Information System (INIS)

Palau, J.M.

1997-01-01

The aim of this thesis was to evaluate how much integral slab experiments can both reduce discrepancies between experimental results and calculations, and improve the knowledge of hafnium isotopes neutronic parameters by an adapted sensitivity and uncertainty method. A statistical approach, based on the generalized least squares method and perturbation theory, has been incorporated into our calculation system in order to deduce microscopic cross-section adjustments from observed integral measurements on this particular 'mock-up' reactor. In this study it has been established that the correlations between integral parameters and hafnium capture cross-sections enable specific variations in the region of resolved resonances at the level of multigroup and punctual cross-sections recommended data (JEF-2.2 evaluation) to be highlighted. The use of determinist methods (APOLLO2 code) together with Monte Carlo- type simulations (TRIPOLI4 code) enabled a depth analysis of the modelling approximations to be carried out. Furthermore, the sensitivity coefficient validation technique employed leads to a reliable assessment of the quality of the new basic nuclear data. In this instance, the adjustments proposed for certain isotope 177 Hf resonance parameters reduce, after error propagation, by 3 to 5 per cent the difference between experimental results and calculations related to this absorbent's efficiency. Beyond this particular application, the qualification methodology integrated in our calculation system should enable other basic sizing parameters to be treated (chemical / geometric data or other unexplored nuclear data) to make technological requirements less stringent. (author)

Extraction of hafnium with chelating agents from aqueous-alcoholic solutions

International Nuclear Information System (INIS)

Hala, J.; Prihoda, J.

1975-01-01

The extraction was studied of hafnium into solutions of N-benzoyl-N-phenylhydroxylamine, 2-thenoyltrifluoroacetone and di-n-butylphosphoric acid in benzene, toluene, chloroform and tetrachloromethane from aqueous alcoholic solutions with a formal acidity of 2M-HClO 4 . Methyl-, ethyl-, n- and isopropyl- and tert-butyl alcohol were used as organic components in the mixed aqueous-organic phase. In the extraction into N-benzoyl-N-phenylhydroxylamine the presence of the alcohols resulted in synergic effects analogous to the previously described extraction by substituted benzoylpyrazolone. With the other two extractants, the effect of the alcohols was antagonistic, due to the interaction of alcohol or water with the reagent in the organic phase, and to the decrease in the reagent distribution constant. (author)

Studies of high-K isomers in hafnium nuclei

International Nuclear Information System (INIS)

Sletten, G.; Gjoerup, N.L.

1991-01-01

K-isomeric states built on high-Ω Nilsson orbitals from deformation-aligned high-j levels near the Fermi surface are found to cluster in the neutron rich Hf, W and Os nuclei. It has been shown that some of the high seniority states of this type have decay properties that indicate strong mixing of configurations and that in Osmium nuclei γ-softness cause strong deviations from the well established K-selection rule. Also in the Hafnium nuclei is the expected forbiddenness in isomeric decays an order of magnitude smaller than expected from the K-selection rule. A new 9 quasiparticle isomer has been discovered in 175 Hf at I=57/2. This isomer has the anomalous decay as the dominant mode. Other lower seniority states are also identified. At spin 35/2 and 45/2 the deformation aligned states become yrast, but the structure of the yrast line to even higher spins is not yet understood. (author)

Luminescent determination of zirconium and hafnium with myricetin

International Nuclear Information System (INIS)

Talipov, Sh.T.; Zel'tser, L.E.; Morozova, L.A.; Tashkhodzhaev, A.T.

1978-01-01

Reaction of formation of 3, 5, 7, 3', 4', 5' - hexaoxiflavone - myricetin complexes with zirconium and hafnium ions has been the basis for development of luminescent method of determining these elements. Optimum conditions for complexing have been determined. For Hf they are : 8-9 HCl concentration, maximum fluorescence wave length (lambda fl.)of 520 nm, wave length of exciting light (lambda el) of 436 nm, for Zr lambda fl = 536nm, lambda el = 436 nm. Stable fluorescence establishes after 25 min. for Zr and after 15 min for Hf in the presence of 40% ethanol. Usage of various camouflage agents has permitted to attain high selectivity of the method. Possibility for determination of Zr with myricetin in the presence of a 10-time excess of Hf, Cr, Cu, 50-time excess of Mo and Ti is shown. Sensitivity of Zr determination is 2.0x10 μg -2 /ml, for Hf it is 9.0x10 μg -3 and mineral waters

Amorphous Hafnium-Indium-Zinc Oxide Semiconductor Thin Film Transistors

Directory of Open Access Journals (Sweden)

Sheng-Po Chang

2012-01-01

Full Text Available We reported on the performance and electrical properties of co-sputtering-processed amorphous hafnium-indium-zinc oxide (α-HfIZO thin film transistors (TFTs. Co-sputtering-processed α-HfIZO thin films have shown an amorphous phase in nature. We could modulate the In, Hf, and Zn components by changing the co-sputtering power. Additionally, the chemical composition of α-HfIZO had a significant effect on reliability, hysteresis, field-effect mobility (μFE, carrier concentration, and subthreshold swing (S of the device. Our results indicated that we could successfully and easily fabricate α-HfIZO TFTs with excellent performance by the co-sputtering process. Co-sputtering-processed α-HfIZO TFTs were fabricated with an on/off current ratio of ~106, higher mobility, and a subthreshold slope as steep as 0.55 V/dec.

49 CFR 173.23 - Previously authorized packaging.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Previously authorized packaging. 173.23 Section... REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Preparation of Hazardous Materials for Transportation § 173.23 Previously authorized packaging. (a) When the regulations specify a packaging with a specification marking...

14 CFR 25.173 - Static longitudinal stability.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Static longitudinal stability. 25.173... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Flight Stability § 25.173 Static... forces (including friction) must be as follows: (a) A pull must be required to obtain and maintain speeds...

Differential perturbed angular correlation: use of physico-chemical study of some hafnium complexes derivates of hydroxy acids and EDTA

International Nuclear Information System (INIS)

Silveira, J.G. da.

1981-01-01

Measures of quadrupolar interaction to nucleus level of the metal, in some hafnium complexes are presented, including the analysis by combustion, microanalysis, infrared spectroscopy and thermogravimetry. The hyperfine interaction parameters, the temperature effects and the thermal neutrons capture effects over the irradiated Hf Y (Y = EDTA) are also studied. (author)

19 CFR 173.1 - Authority to review for error.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Authority to review for error. 173.1 Section 173.1 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND SECURITY; DEPARTMENT OF THE TREASURY (CONTINUED) ADMINISTRATIVE REVIEW IN GENERAL § 173.1 Authority to review for error. Port directors...

Rhodium and Hafnium Influence on the Microstructure, Phase Composition, and Oxidation Resistance of Aluminide Coatings

OpenAIRE

Maryana Zagula-Yavorska; Małgorzata Wierzbińska; Jan Sieniawski

2017-01-01

A 0.5 μm thick layer of rhodium was deposited on the CMSX 4 superalloy by the electroplating method. The rhodium-coated superalloy was hafnized and aluminized or only aluminized using the Chemical vapour deposition method. A comparison was made of the microstructure, phase composition, and oxidation resistance of three aluminide coatings: nonmodified (a), rhodium-modified (b), and rhodium- and hafnium-modified (c). All three coatings consisted of two layers: the additive layer and the interdi...

Study of bulk Hafnium oxide (HfO2) under compression

Science.gov (United States)

Pathak, Santanu; Mandal, Guruprasad; Das, Parnika

2018-04-01

Hafnium oxide (HfO2) is a technologically important material. This material has K-value of 25 and band gap 5.8 eV. A k value of 25-30 is preferred for a gate dielectric [1]. As it shows good insulating and capacitive properties, HfO2 is being considered as a replacement to SiO2 in microelectronic devices as gate dielectrics. On the other hand because of toughening mechanism due to phase transformation induced by stress field observed in these oxides, HFO2 has been a material of investigations in various configurations for a very long time. However the controversies about phase transition of HfO2 under pressure still exists. High quality synchrotron radiation has been used to study the structural phase transition of HfO2 under pressure.

Hafnium at subduction zones: isotopic budget of input and output fluxes; L'hafnium dans les zones de subduction: bilan isotopique des flux entrant et sortant

Energy Technology Data Exchange (ETDEWEB)

Marini, J.Ch

2004-05-15

Subduction zones are the primary regions of mass exchanges between continental crust and mantle of Earth through sediment subduction toward the earth's mantle and by supply of mantellic magmas to volcanic arcs. We analyze these mass exchanges using Hafnium and Neodymium isotopes. At the Izu-Mariana subduction zone, subducting sediments have Hf and Nd isotopes equivalent to Pacific seawater. Altered oceanic crust has Hf and Nd isotopic compositions equivalent to the isotopic budget of unaltered Pacific oceanic crust. At Luzon and Java subduction zones, arc lavas present Hf isotopic ratios highly radiogenic in comparison to their Nd isotopic ratios. Such compositions of the Luzon and Java arc lavas are controlled by a contamination of their sources by the subducted oceanic sediments. (author)

7 CFR 993.173 - Reports of accounting.

Science.gov (United States)

2010-01-01

... 7 Agriculture 8 2010-01-01 2010-01-01 false Reports of accounting. 993.173 Section 993.173... accounting. (a) Independent handler's reports of accounting. Within 10 days (exclusive of Saturdays, Sundays... association, makes an accounting or settlement with a producer or dehydrator for prunes delivered to him, he...

49 CFR 173.194 - Gas identification sets.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Gas identification sets. 173.194 Section 173.194... Gas identification sets. Gas identification sets containing poisonous material must be packaged in... silical gel, gas identification sets may be shipped as follows: (1) If the poisonous material does not...

49 CFR 173.219 - Life-saving appliances.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Life-saving appliances. 173.219 Section 173.219... Life-saving appliances. (a) A life-saving appliance, self-inflating or non-self-inflating, containing small quantities of hazardous materials that are required as part of the life-saving appliance must...

40 CFR 265.173 - Management of containers.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Management of containers. 265.173... DISPOSAL FACILITIES Use and Management of Containers § 265.173 Management of containers. (a) A container... waste. (b) A container holding hazardous waste must not be opened, handled, or stored in a manner which...

40 CFR 264.173 - Management of containers.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 25 2010-07-01 2010-07-01 false Management of containers. 264.173... Use and Management of Containers § 264.173 Management of containers. (a) A container holding hazardous... container holding hazardous waste must not be opened, handled, or stored in a manner which may rupture the...

14 CFR 23.173 - Static longitudinal stability.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Static longitudinal stability. 23.173... Stability § 23.173 Static longitudinal stability. Under the conditions specified in § 23.175 and with the airplane trimmed as indicated, the characteristics of the elevator control forces and the friction within...

21 CFR 173.250 - Methyl alcohol residues.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methyl alcohol residues. 173.250 Section 173.250 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD.... Methyl alcohol may be present in the following foods under the conditions specified: (a) In spice...

49 CFR 173.2 - Hazardous materials classes and index to hazard class definitions.

Science.gov (United States)

2010-10-01

....50 1 1.6 Extremely insensitive detonating substances 173.50 2 2.1 Flammable gas 173.115 2 2.2 Non-flammable compressed gas 173.115 2 2.3 Poisonous gas 173.115 3 Flammable and combustible liquid 173.120 4 4.1 Flammable solid 173.124 4 4.2 Spontaneously combustible material 173.124 4 4.3 Dangerous when wet...

Hafnium at subduction zones: isotopic budget of input and output fluxes

International Nuclear Information System (INIS)

Marini, J.Ch.

2004-05-01

Subduction zones are the primary regions of mass exchanges between continental crust and mantle of Earth through sediment subduction toward the earth's mantle and by supply of mantellic magmas to volcanic arcs. We analyze these mass exchanges using Hafnium and Neodymium isotopes. At the Izu-Mariana subduction zone, subducting sediments have Hf and Nd isotopes equivalent to Pacific seawater. Altered oceanic crust has Hf and Nd isotopic compositions equivalent to the isotopic budget of unaltered Pacific oceanic crust. At Luzon and Java subduction zones, arc lavas present Hf isotopic ratios highly radiogenic in comparison to their Nd isotopic ratios. Such compositions of the Luzon and Java arc lavas are controlled by a contamination of their sources by the subducted oceanic sediments. (author)

49 CFR 173.6 - Materials of trade exceptions.

Science.gov (United States)

2010-10-01

...-reactive (see § 173.124), poisonous by inhalation (see § 173.133), or a hazardous waste. (b) Packaging. (1..., boxes or compartments. (4) For gasoline, a packaging must be made of metal or plastic and conform to the...

27 CFR 25.173 - Brewer in default.

Science.gov (United States)

2010-04-01

... 27 Alcohol, Tobacco Products and Firearms 1 2010-04-01 2010-04-01 false Brewer in default. 25.173... OF THE TREASURY LIQUORS BEER Tax on Beer Prepayment of Tax § 25.173 Brewer in default. (a) When a... the brewer is otherwise in default in payment of tax under § 25.164, beer may not be removed for...

Thermal expansion studies on Hafnium titanate (HfTiO4)

International Nuclear Information System (INIS)

Panneerselvam, G.; Subramanian, G.G.S.; Antony, M.P.

2006-01-01

The lattice thermal expansion characteristics of hafnium titanate (HfTiO 4 ) have been studied by measuring the lattice parameter as a function of temperature by high temperature X-ray diffraction technique (HT-XRD) in the temperature range 298-1973K. Percentage linear thermal expansion and mean linear thermal expansion coefficients were computed from the lattice parameter data. The thermal expansion of HfTiO 4 is highly anisotropic. The expansivity along 'a' axis is large; as compared to the expansivity along 'b' axis which is negative below 1073 K. The percentage linear thermal expansion in the temperature range 298-1973 K along a, b and c axis are 2.74, 0.901 and 1.49 respectively. Thermal expansion values obtained in the present study are in reasonable agreement with the existing thermal expansion data. (author)

36 CFR 1192.173 - Automated guideway transit vehicles and systems.

Science.gov (United States)

2010-07-01

.... Vertical alignment may be accomplished by vehicle air suspension or other suitable means of meeting the... vehicles and systems. 1192.173 Section 1192.173 Parks, Forests, and Public Property ARCHITECTURAL AND... TRANSPORTATION VEHICLES Other Vehicles and Systems § 1192.173 Automated guideway transit vehicles and systems. (a...

32 CFR 173.3 - Profit reduction clause.

Science.gov (United States)

2010-07-01

... 32 National Defense 1 2010-07-01 2010-07-01 false Profit reduction clause. 173.3 Section 173.3... violating 18 U.S.C. 201-224 (bribery, graft, and conflicts of interest), 18 U.S.C. 371 (conspiracy), 18 U.S.... 1341 (fraud), 18 U.S.C. 1343 (fraud by wire) for any act in connection with or related to the obtaining...

19 CFR 191.173 - Imported duty-paid derivatives (no manufacture).

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Imported duty-paid derivatives (no manufacture). 191.173 Section 191.173 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND... § 191.173 Imported duty-paid derivatives (no manufacture). When the basis for drawback under 19 U.S.C...

Surface State Capture Cross-Section at the Interface between Silicon and Hafnium Oxide

Directory of Open Access Journals (Sweden)

Fu-Chien Chiu

2013-01-01

Full Text Available The interfacial properties between silicon and hafnium oxide (HfO2 are explored by the gated-diode method and the subthreshold measurement. The density of interface-trapped charges, the current induced by surface defect centers, the surface recombination velocity, and the surface state capture cross-section are obtained in this work. Among the interfacial properties, the surface state capture cross-section is approximately constant even if the postdeposition annealing condition is changed. This effective capture cross-section of surface states is about 2.4 × 10−15 cm2, which may be an inherent nature in the HfO2/Si interface.

A thermally robust and thickness independent ferroelectric phase in laminated hafnium zirconium oxide

Directory of Open Access Journals (Sweden)

S. Riedel

2016-09-01

Full Text Available Ferroelectric properties in hafnium oxide based thin films have recovered the scaling potential for ferroelectric memories due to their ultra-thin-film- and CMOS-compatibility. However, the variety of physical phenomena connected to ferroelectricity allows a wider range of applications for these materials than ferroelectric memory. Especially mixed HfxZr1-xO2 thin films exhibit a broad compositional range of ferroelectric phase stability and provide the possibility to tailor material properties for multiple applications. Here it is shown that the limited thermal stability and thick-film capability of HfxZr1-xO2 can be overcome by a laminated approach using alumina interlayers.

1 CFR 17.3 - Criteria for emergency publication.

Science.gov (United States)

2010-01-01

... 1 General Provisions 1 2010-01-01 2010-01-01 false Criteria for emergency publication. 17.3..., AND PROCESSING OF DOCUMENTS FILING FOR PUBLIC INSPECTION AND PUBLICATION SCHEDULES Emergency Schedule § 17.3 Criteria for emergency publication. The emergency schedule is designed to provide the fastest...

21 CFR 133.173 - Pasteurized process cheese food.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Pasteurized process cheese food. 133.173 Section 133.173 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION CHEESES AND RELATED CHEESE PRODUCTS Requirements for Specific...

Influence of plastic deformation on nitriding of a molybdenum-hafnium alloy

International Nuclear Information System (INIS)

Lakhtin, Yu.M.; Kogan, Ya.D.; Shashkov, D.P.; Likhacheva, T.E.

1982-01-01

The influence of a preliminary plastic strain on the structure and properties of molybdenum alloy with 0.2 wt.% Hf upon nitriding in the ammonia medium at 900-1200 deg C during 1-6 h is investigated. The study of microhardness distribution across the nitrided layer thickness has shown that with increase of the degree of preliminary plastic strain up to 50 % the nitrided layer hardness decreases and with further reduction growth up to 90 % - increases. Nitriding sharply (hundred times) increases wear resistance of molybdenum alloy with hafnium addition. At the reduction degree 25 % the wear resistance is less than at other values of percentage reduction in area owing to the minimum thickness of the nitride zone. The alloy strained before nitriding by 25 % has shown the best results during heat resistance testing

49 CFR 173.206 - Packaging requirements for chlorosilanes.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Packaging requirements for chlorosilanes. 173.206...-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Non-bulk Packaging for Hazardous Materials Other Than Class 1 and Class 7 § 173.206 Packaging requirements for chlorosilanes. (a) When § 172.101 of this...

Dielectric response and ac conductivity analysis of hafnium oxide nanopowder

International Nuclear Information System (INIS)

Karahaliou, P K; Xanthopoulos, N; Krontiras, C A; Georga, S N

2012-01-01

The dielectric response of hafnium oxide nanopowder was studied in the frequency range of 10 -2 -10 6 MHz and in the temperature range of 20-180 °C. Broadband dielectric spectroscopy was applied and the experimental results were analyzed and discussed using the electric modulus (M*) and alternating current (ac) conductivity formalisms. The analyses of the dc conductivity and electric modulus data revealed the presence of mechanisms which are thermally activated, both with almost the same activation energy of 1.01 eV. A fitting procedure involving the superposition of the thermally activated dc conductivity, the universal dielectric responce and the near constant loss terms has been used to describe the frequency evolution of the real part of the specific electrical conductivity. The conductivity master curve was obtained, suggesting that the time-temperature superposition principle applies for the studied system, thus implying that the conductivity mechanisms are temperature independent.

Interface and oxide traps in high-κ hafnium oxide films

International Nuclear Information System (INIS)

Wong, H.; Zhan, N.; Ng, K.L.; Poon, M.C.; Kok, C.W.

2004-01-01

The origins of the interface trap generation and the effects of thermal annealing on the interface and bulk trap distributions are studied in detail. We found that oxidation of the HfO 2 /Si interface, removal of deep trap centers, and crystallization of the as-deposited film will take place during the post-deposition annealing (PDA). These processes will result in the removal of interface traps and deep oxide traps and introduce a large amount of shallow oxide traps at the grain boundaries of the polycrystalline film. Thus, trade-off has to be made in considering the interface trap density and oxide trap density when conducting PDA. In addition, the high interface trap and oxide trap densities of the HfO 2 films suggest that we may have to use the SiO 2 /HfO 2 stack or hafnium silicate structure for better device performance

Effects of oxygen partial pressure and annealing temperature on the residual stress of hafnium oxide thin-films on silicon using synchrotron-based grazing incidence X-ray diffraction

Energy Technology Data Exchange (ETDEWEB)

Biswas, Debaleen [Saha Institute of Nuclear Physics, 1/AF Bidhannagar, Kolkata 700 064 (India); Sinha, Anil Kumar [ISU, Raja Ramanna Centre for Advanced Technology, Indore 452 013 (India); Homi Bhabha National Institute, BARC, Mumbai 400 094 (India); Chakraborty, Supratic, E-mail: supratic.chakraborty@saha.ac.in [Saha Institute of Nuclear Physics, 1/AF Bidhannagar, Kolkata 700 064 (India)

2016-10-30

Highlights: • Residual stress estimation thin hafnium oxide film with thickness of <10 nm. • A mathematical expression is proposed for stress estimation of thin-film using GIXRD. • Residual stress varies with argon content in Ar/O{sub 2} plasma and annealing temperature. • Variation of stress is explained by IL swelling and enhanced structural relaxation. - Abstract: Synchrotron radiation-based grazing incidence X-ray diffraction (GI-XRD) technique is employed here to estimate the residual stress of < 10 nm thin hafnium oxide film deposited on Si (100) substrate at different argon/oxygen ratios using reactive rf sputtering. A decrease in residual stress, tensile in nature, is observed at higher annealing temperature for the samples deposited with increasing argon ratio in the Ar/O{sub 2} plasma. The residual stress of the films deposited at higher p{sub Ar} (Ar:O{sub 2} = 4:1) is also found to be decreased with increasing annealing temperature. But the stress is more or less constant with annealing temperature for the films deposited at lower Ar/O{sub 2} (1:4) ratio. All the above phenomena can be explained on the basis of swelling of the interfacial layer and enhanced structural relaxation in the presence of excess Hf in hafnium oxide film during deposition.

49 CFR 173.316 - Cryogenic liquids in cylinders.

Science.gov (United States)

2010-10-01

... filling density for hydrogen, cryogenic liquid is defined as the percent ratio of the weight of lading in... 49 Transportation 2 2010-10-01 2010-10-01 false Cryogenic liquids in cylinders. 173.316 Section... REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.316 Cryogenic liquids in...

Pyroelectricity of silicon-doped hafnium oxide thin films

Science.gov (United States)

Jachalke, Sven; Schenk, Tony; Park, Min Hyuk; Schroeder, Uwe; Mikolajick, Thomas; Stöcker, Hartmut; Mehner, Erik; Meyer, Dirk C.

2018-04-01

Ferroelectricity in hafnium oxide thin films is known to be induced by various doping elements and in solid-solution with zirconia. While a wealth of studies is focused on their basic ferroelectric properties and memory applications, thorough studies of the related pyroelectric properties and their application potential are only rarely found. This work investigates the impact of Si doping on the phase composition and ferro- as well as pyroelectric properties of thin film capacitors. Dynamic hysteresis measurements and the field-free Sharp-Garn method were used to correlate the reported orthorhombic phase fractions with the remanent polarization and pyroelectric coefficient. Maximum values of 8.21 µC cm-2 and -46.2 µC K-1 m-2 for remanent polarization and pyroelectric coefficient were found for a Si content of 2.0 at%, respectively. Moreover, temperature-dependent measurements reveal nearly constant values for the pyroelectric coefficient and remanent polarization over the temperature range of 0 ° C to 170 ° C , which make the material a promising candidate for IR sensor and energy conversion applications beyond the commonly discussed use in memory applications.

Implantation of titanium, chromium, yttrium, molybdenum, silver, hafnium, tantalum, tungsten and platinum ions generated by a metal vapor vacuum ion source into 440C stainless steel

International Nuclear Information System (INIS)

Sasaki, Jun; Hayashi, Kazunori; Sugiyama, Kenji; Ichiko, Osami; Hashiguchi, Yoshihiro

1992-01-01

Titanium, yttrium, molybdenum, silver, chromium, hafnium, tantalum, tungsten and platinum ions generated by a metal vapor vacuum arc (MEVVA) ion source were implanted into 440C stainless steel in the dose region 10 17 ions cm -2 with extraction voltages of up to 70 kV. Glow discharge spectroscopy (GDS), friction coefficient, and Vickers microhardness of the specimens were studied. Grooves made by friction tests were investigated by electron probe microanalysis (EPMA). GDS showed incorporation of carbon in the yttrium, hafnium, tantalum, tungsten and platinum implanted specimens, as well as titanium implanted samples. A large amount of oxygen was observed in the yttrium implanted specimen. The friction coefficient was measured by reciprocating sliding of an unimplanted 440C ball without lubricant at a load of 0.245 N. The friction decreased and achieved a stable state after implantation of titanium, hafnium and tantalum. The friction coefficient of the platinum implanted specimen showed a gradual decrease after several cycles of sliding at high friction coefficient. The yttrium implanted sample exhibited a decreased but slightly unstable friction coefficient. Results from EPMA showed that the implanted elements, which gave decreased friction, remained even after sliding of 200 cycles. Implantation of chromium, molybdenum, silver and tungsten did not provide a decrease in friction and the implants were gone from the wear grooves after the sliding tests. (orig.)

49 CFR 173.189 - Batteries containing sodium or cells containing sodium.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Batteries containing sodium or cells containing sodium. 173.189 Section 173.189 Transportation Other Regulations Relating to Transportation PIPELINE AND... Than Class 1 and Class 7 § 173.189 Batteries containing sodium or cells containing sodium. (a...

Critical evaluation of the determination of zirconium and hafnium by instrumental and radiochemical neutron activation analysis

International Nuclear Information System (INIS)

Burger, Mario; Kraehenbuehl, Urs

1991-01-01

Neutron activation analysis (instrument or radiochemical) is suitable for the determination of zirconium and hafnium in samples of geochemical origin only when sufficient attention is paid to inter-fering nuclides. The size of the necessary correction for INAA depends on the composition of the sample; this problem is discussed. The radio-chemical technique which is recommended involves separation of the samples, precipitations and anion-exchange separation. Results are given for various standard reference materials and for meteorites. (author). 12 refs.; 1 fig.; 9 tabs

9 CFR 381.173 - Mechanically Separated (Kind of Poultry).

Science.gov (United States)

2010-01-01

... Poultry). 381.173 Section 381.173 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE, DEPARTMENT OF AGRICULTURE AGENCY ORGANIZATION AND TERMINOLOGY; MANDATORY MEAT AND POULTRY PRODUCTS INSPECTION AND VOLUNTARY INSPECTION AND CERTIFICATION POULTRY PRODUCTS INSPECTION REGULATIONS Definitions and...

A fast response hafnium selective polymeric membrane electrode based on N,N'-bis(α-methyl-salicylidene)-dipropylenetriamine as a neutral carrier

International Nuclear Information System (INIS)

Rezaei, B.; Meghdadi, S.; Zarandi, R. Fazel

2008-01-01

In this study a new hafnium selective sensor was fabricated from polyvinylchloride (PVC) matrix membrane containing neutral carrier N,N'-bis(α-methyl-salicylidene)-dipropylenetriamine (Mesaldpt) as a new ionophore, sodium tetraphenyl borate (NaTPB) as anionic discriminator and dioctyl phthalate (DOP) as plasticizing solvent mediator in tetrahydrofuran solvent. The electrode exhibits Nernstian response for Hf 4+ (Hafnium(IV)) over a wide concentration range (2.0 x 10 -7 to 1.0 x 10 -1 M) with the determination coefficient of 0.9966 and slope of 15.1 ± 0.1 mV decades -1 . The limit of detection is 1.9 x 10 -7 M. The electrode has a fast response time of 18 s and a working pH range of 4-8. The proposed membrane shows excellent discriminating ability towards Hf 4+ ion with regard to several alkali, alkaline earth transition and heavy metal ions. It can be used over a period of 1.5 months with good reproducibility. It is successfully applied for direct determination of Hf 4+ in solutions by standard addition method for real sample analysis

Study of hafnium (IV) oxide nanoparticles synthesized by polymerized complex and polymer precursor derived sol-gel methods

KAUST Repository

Ramos-Gonzá lez, R.; Garcí a-Cerda, L. A.; Alshareef, Husam N.; Gnade, Bruce E.; Quevedo-Ló pez, Manuel Angel Quevedo

2010-01-01

This work reports the preparation and characterization of hafnium (IV) oxide (HfO2) nanoparticles grown by derived sol-gel routes that involves the formation of an organic polymeric network. A comparison between polymerized complex (PC) and polymer precursor (PP) methods is presented. For the PC method, citric acid (CA) and ethylene glycol (EG) are used as the chelating and polymerizable reagents, respectively. In the case of PP method, poly(acrylic acid) (PAA) is used as the chelating reagent. In both cases, different precursor gels were prepared and the hafnium (IV) chloride (HfCl4) molar ratio was varied from 0.1 to 1.0 for the PC method and from 0.05 to 0.5 for the PP method. In order to obtain the nanoparticles, the precursors were heat treated at 500 and 800 °C. The thermal characterization of the precursor gels was carried out by thermogravimetric analysis (TGA) and the structural and morphological characterization by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The XRD patterns of the samples obtained by both methods shows the formation of HfO2 at 500 °C with monoclinic crystalline phase. The PC method exhibited also the cubic phase. Finally, the HfO2 nanoparticles size (4 to 11 nm) was determined by TEM and XRD patterns. © (2010) Trans Tech Publications.

Study of hafnium (IV) oxide nanoparticles synthesized by polymerized complex and polymer precursor derived sol-gel methods

KAUST Repository

Ramos-González, R.

2010-03-01

This work reports the preparation and characterization of hafnium (IV) oxide (HfO2) nanoparticles grown by derived sol-gel routes that involves the formation of an organic polymeric network. A comparison between polymerized complex (PC) and polymer precursor (PP) methods is presented. For the PC method, citric acid (CA) and ethylene glycol (EG) are used as the chelating and polymerizable reagents, respectively. In the case of PP method, poly(acrylic acid) (PAA) is used as the chelating reagent. In both cases, different precursor gels were prepared and the hafnium (IV) chloride (HfCl4) molar ratio was varied from 0.1 to 1.0 for the PC method and from 0.05 to 0.5 for the PP method. In order to obtain the nanoparticles, the precursors were heat treated at 500 and 800 °C. The thermal characterization of the precursor gels was carried out by thermogravimetric analysis (TGA) and the structural and morphological characterization by X-ray diffraction (XRD) and transmission electron microscopy (TEM). The XRD patterns of the samples obtained by both methods shows the formation of HfO2 at 500 °C with monoclinic crystalline phase. The PC method exhibited also the cubic phase. Finally, the HfO2 nanoparticles size (4 to 11 nm) was determined by TEM and XRD patterns. © (2010) Trans Tech Publications.

Rapid formation of nanocrystalline HfO2 powders from amorphous hafnium hydroxide under ultrasonically assisted hydrothermal treatment

International Nuclear Information System (INIS)

Meskin, Pavel E.; Sharikov, Felix Yu.; Ivanov, Vladimir K.; Churagulov, Bulat R.; Tretyakov, Yury D.

2007-01-01

Peculiarities of hafnium hydroxide hydrothermal decomposition were studied by in situ heat flux calorimetry for the first time. It was shown that this process occurs in one exothermal stage (ΔH = -17.95 kJ mol -1 ) at 180-250 deg. C resulting in complete crystallization of amorphous phase with formation of pure monoclinic HfO 2 . It was found that the rate of m-HfO 2 formation can be significantly increased by combining hydrothermal treatment with simultaneous ultrasonic activation

Improvement of aging kinetics and precipitate size refinement in Mg–Sn alloys by hafnium additions

Energy Technology Data Exchange (ETDEWEB)

Behdad, S. [Department of Mechanical and Materials Engineering, Florida International University, Miami, FL 33174 (United States); Zhou, L. [Department of Materials Science and Engineering and Advanced Materials Processing and Analysis Center, University of Central Florida, Orlando, FL 32816 (United States); Henderson, H.B.; Manuel, M.V. [Department of Materials Science and Engineering, University of Florida, Gainesville, FL 32611 (United States); Sohn, Y. [Department of Materials Science and Engineering and Advanced Materials Processing and Analysis Center, University of Central Florida, Orlando, FL 32816 (United States); Agarwal, A. [Department of Mechanical and Materials Engineering, Florida International University, Miami, FL 33174 (United States); Boesl, B., E-mail: bboesl@fiu.edu [Department of Mechanical and Materials Engineering, Florida International University, Miami, FL 33174 (United States)

2016-01-10

Two Mg–Sn alloys were microalloyed by addition of Hafnium and their age-hardening response was studied at 200 °C. Time to reach peak hardness was significantly reduced and improved by Hf addition. TEM study showed Hf clusters in the close vicinity and at the surface of Mg{sub 2}Sn precipitates, which confirms that Hf clusters act as additional nucleation centers for Mg{sub 2}Sn precipitate formation. Our results support the validity of thermokinetic criterion proposed by Mendis for selection of microalloying elements in order to refine precipitate size, accelerate aging kinetics and enhance peak hardness.

21 CFR 173.70 - Chloromethylated aminated styrene-divinylbenzene resin.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Chloromethylated aminated styrene-divinylbenzene resin. 173.70 Section 173.70 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) FOOD FOR HUMAN CONSUMPTION (CONTINUED) SECONDARY DIRECT FOOD ADDITIVES PERMITTED IN FOOD FOR HUMAN CONSUMPTION Polymer...

Solvent extraction of hafnium(IV) by dinonylnaphthalene sulfonic acid from mixed aqueous-organic media

International Nuclear Information System (INIS)

Hala, J.; Piperkovova, H.

1979-01-01

The extraction of hafnium(IV) by heptane and toluene solutions of dinonylnaphthalene sulfonic acid (HD) from mixed aqueous-organic solutions has been studied. Alcohols, ketones, carboxylic acids, cyclic ethers, dimethylsulfoxide and dimethylformamide were used as the organic component of the mixed phase. Methanol, ethanol, formic acid and dioxane increased the extractability of Hf(IV) whereas other solvents showed only an antagonistic effect. The results were discussed from the point of view of the changes in micellar structure of HD, and compared with the uptake of Hf(IV) by resinous cation exchangers. The solubilization by HD of alcohols, carboxylic acids and dimethylsulfoxide was demonstrated by using the corresponding 14 C and 35 S labelled compounds. (author)

The interfacial orientation relationship of oxide nanoparticles in a hafnium-containing oxide dispersion-strengthened austenitic stainless steel

Energy Technology Data Exchange (ETDEWEB)

Miao, Yinbin, E-mail: miao2@illinois.edu [Department of Nuclear, Plasma and Radiological Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States); Mo, Kun [Nuclear Engineering Division, Argonne National Laboratory, Lemont, IL 60493 (United States); Cui, Bai [Department of Mechanical and Materials Engineering, University of Nebraska-Lincoln, Lincoln, NE 68588 (United States); Department of Material Science and Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States); Chen, Wei-Ying [Department of Nuclear, Plasma and Radiological Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States); Miller, Michael K.; Powers, Kathy A. [Center for Nanophase Materials Sciences, Oak Ridge National Laboratory, Oak Ridge, TN 37830 (United States); McCreary, Virginia; Gross, David [Department of Material Science and Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States); Almer, Jonathan [X-ray Science Division, Argonne National Laboratory, Lemont, IL 60493 (United States); Robertson, Ian M. [Department of Material Science and Engineering, University of Wisconsin-Madison, Madison, WA 53706 (United States); Department of Material Science and Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States); Stubbins, James F. [Department of Nuclear, Plasma and Radiological Engineering, University of Illinois at Urbana-Champaign, Urbana, IL 61801 (United States)

2015-03-15

This work reports comprehensive investigations on the orientation relationship of the oxide nanoparticles in a hafnium-containing austenitic oxide dispersion-strengthened 316 stainless steel. The phases of the oxide nanoparticles were determined by a combination of scanning transmission electron microscopy–electron dispersive X-ray spectroscopy, atom probe tomography and synchrotron X-ray diffraction to be complex Y–Ti–Hf–O compounds with similar crystal structures, including bixbyite Y{sub 2}O{sub 3}, fluorite Y{sub 2}O{sub 3}–HfO{sub 2} solid solution and pyrochlore (or fluorite) Y{sub 2}(Ti,Hf){sub 2−x}O{sub 7−x}. High resolution transmission electron microscopy was used to characterize the particle–matrix interfaces. Two different coherency relationships along with one axis-parallel relation between the oxide nanoparticles and the steel matrix were found. The size of the nanoparticles significantly influences the orientation relationship. The results provide insight into the relationship of these nanoparticles with the matrix, which has implications for interpreting material properties as well as responses to radiation. - Highlights: • The oxide nanoparticles in a hafnium-containing austenitic ODS were characterized. • The nanoparticles are Y–Hf–Ti–O enriched phases according to APT and STEM–EDS. • Two coherency and an axis-parallel orientation relationships were found by HR-TEM. • Particle size has a prominent effect on the orientation relationship (OR). • Formation mechanism of the oxide nanoparticles was discussed based on the ORs.

49 CFR 173.182 - Barium azide-50 percent or more water wet.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Barium azide-50 percent or more water wet. 173.182 Section 173.182 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS... Class 1 and Class 7 § 173.182 Barium azide—50 percent or more water wet. Barium azide—50 percent or more...

Hafnium oxide nanoparticles: toward an in vitro predictive biological effect?

International Nuclear Information System (INIS)

Marill, Julie; Anesary, Naeemunnisa Mohamed; Zhang, Ping; Vivet, Sonia; Borghi, Elsa; Levy, Laurent; Pottier, Agnes

2014-01-01

Hafnium oxide, NBTXR3 nanoparticles were designed for high dose energy deposition within cancer cells when exposed to ionizing radiation. The purpose of this study was to assess the possibility of predicting in vitro the biological effect of NBTXR3 nanoparticles when exposed to ionizing radiation. Cellular uptake of NBTXR3 nanoparticles was assessed in a panel of human cancer cell lines (radioresistant and radiosensitive) by transmission electron microscopy. The radioenhancement of NBTXR3 nanoparticles was measured by the clonogenic survival assay. NBTXR3 nanoparticles were taken up by cells in a concentration dependent manner, forming clusters in the cytoplasm. Differential nanoparticle uptake was observed between epithelial and mesenchymal or glioblastoma cell lines. The dose enhancement factor increased with increase NBTXR3 nanoparticle concentration and radiation dose. Beyond a minimum number of clusters per cell, the radioenhancement of NBTXR3 nanoparticles could be estimated from the radiation dose delivered and the radiosensitivity of the cancer cell lines. Our preliminary results suggest a predictable in vitro biological effect of NBTXR3 nanoparticles exposed to ionizing radiation

49 CFR 173.218 - Fish meal or fish scrap.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Fish meal or fish scrap. 173.218 Section 173.218... Fish meal or fish scrap. (a) Except as provided in Column (7) of the HMT in § 172.101 of this subchapter, fish meal or fish scrap, containing at least 6%, but not more than 12% water, is authorized for...

40 CFR 141.173 - Filtration.

Science.gov (United States)

2010-07-01

... PRIMARY DRINKING WATER REGULATIONS Enhanced Filtration and Disinfection-Systems Serving 10,000 or More People § 141.173 Filtration. A public water system subject to the requirements of this subpart that does... treatment, direct filtration, slow sand filtration, or diatomaceous earth filtration. A public water system...

Nano-scale Radiotherapy-NBTXR3 Hafnium Oxide Nanoparticles as Promising Cancer Therapy

International Nuclear Information System (INIS)

Maggiorella, L.; Barouch, G.; Devaux, C.; Pottier, A.; Levy, L.; Deutsch, E.; Bourhis, J.; Borghi, E.

2011-01-01

Complete text of publication follows: Background: There is considerable interest in approaches that could improve the therapeutic window of radiotherapy, which represents a crucial modality of treatment in oncology. We present the rationale for designing NBTXR3 nanoparticles activated by radiotherapy and validate the concept. We performed the Monte Carlo calculations for the first time based on the 'local model' simulation that showed a dose enhancement of radiation to tumour cells of approximately nine-fold. NBTXR3 was shown to deposit high energy when the ionizing radiation source is 'on' and to have chemically inert behavior in cellular and subcellular systems demonstrated by very good systemic tolerance, thus decreasing potential health hazards. Material and Methods: We used conventional methods, implemented in different ways, to explore interactions of high Z matter and ionizing radiation with biological systems. In addition, microtomography was performed to explore the nanoparticle volume occupancy inside the tumour and its persistence overtime in mouse tumour models. The antitumour activity of NBTXR3 and tolerance were evaluated in Ewing tumour (A673) and fibrosarcoma (HT1080) using high energy source. Results and Conclusion: We created and developed NBTXR3 nanoparticles with a crystalline hafnium oxide core which provide high electron density structure and inert behavior in biological media. NBTXR3 nanoparticles' characteristics, size, charge and shape, allow for efficient interaction with biological entities, cell membrane binding and cellular uptake. The nanoparticles were shown to form clusters at the subcellular level in tumour models. Of most importance, we show NBTXR3 intra-tumour bioavailability with dispersion of nanoparticles in the three dimensions and persistence within the tumour structure, supporting the use of NBTXR3 as effective antitumour therapeutic agent. Antitumour activity of NBTXR3 showed marked advantage in terms of survival, tumour

21 CFR 173.280 - Solvent extraction process for citric acid.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Solvent extraction process for citric acid. 173.280... HUMAN CONSUMPTION Solvents, Lubricants, Release Agents and Related Substances § 173.280 Solvent extraction process for citric acid. A solvent extraction process for recovery of citric acid from...

A fast response hafnium selective polymeric membrane electrode based on N,N'-bis({alpha}-methyl-salicylidene)-dipropylenetriamine as a neutral carrier

Energy Technology Data Exchange (ETDEWEB)

Rezaei, B. [Department of Chemistry, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of)], E-mail: rezaei@cc.iut.ac.ir; Meghdadi, S.; Zarandi, R. Fazel [Department of Chemistry, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of)

2008-08-30

In this study a new hafnium selective sensor was fabricated from polyvinylchloride (PVC) matrix membrane containing neutral carrier N,N'-bis({alpha}-methyl-salicylidene)-dipropylenetriamine (Mesaldpt) as a new ionophore, sodium tetraphenyl borate (NaTPB) as anionic discriminator and dioctyl phthalate (DOP) as plasticizing solvent mediator in tetrahydrofuran solvent. The electrode exhibits Nernstian response for Hf{sup 4+} (Hafnium(IV)) over a wide concentration range (2.0 x 10{sup -7} to 1.0 x 10{sup -1} M) with the determination coefficient of 0.9966 and slope of 15.1 {+-} 0.1 mV decades{sup -1}. The limit of detection is 1.9 x 10{sup -7} M. The electrode has a fast response time of 18 s and a working pH range of 4-8. The proposed membrane shows excellent discriminating ability towards Hf{sup 4+} ion with regard to several alkali, alkaline earth transition and heavy metal ions. It can be used over a period of 1.5 months with good reproducibility. It is successfully applied for direct determination of Hf{sup 4+} in solutions by standard addition method for real sample analysis.

Hafnium-doped hydroxyapatite nanoparticles with ionizing radiation for lung cancer treatment.

Science.gov (United States)

Chen, Min-Hua; Hanagata, Nobutaka; Ikoma, Toshiyuki; Huang, Jian-Yuan; Li, Keng-Yuan; Lin, Chun-Pin; Lin, Feng-Huei

2016-06-01

Recently, photodynamic therapy (PDT) is one of the new clinical options by generating cytotoxic reactive oxygen species (ROS) to kill cancer cells. However, the optical approach of PDT is limited by tissue penetration depth of visible light. In this study, we propose that a ROS-enhanced nanoparticle, hafnium-doped hydroxyapatite (Hf:HAp), which is a material to yield large quantities of ROS inside the cells when the nanoparticles are bombarded with high penetrating power of ionizing radiation. Hf:HAp nanoparticles are generated by wet chemical precipitation with total doping concentration of 15mol% Hf(4+) relative to Ca(2+) in HAp host material. The results show that the HAp particles could be successfully doped with Hf ions, resulted in the formation of nano-sized rod-like shape and with pH-dependent solubility. The impact of ionizing radiation on Hf:HAp nanoparticles is assessed by using in-vitro and in-vivo model using A549 cell line. The 2',7'-dichlorofluorescein diacetate (DCFH-DA) results reveal that after being exposed to gamma rays, Hf:HAp could significantly lead to the formation of ROS in cells. Both cell viability (WST-1) and cytotoxicity (LDH) assay show the consistent results that A549 lung cancer cell lines are damaged with changes in the cells' ROS level. The in-vivo studies further demonstrate that the tumor growth is inhibited owing to the cells apoptosis when Hf:HAp nanoparticles are bombarded with ionizing radiation. This finding offer a new therapeutic method of interacting with ionizing radiation and demonstrate the potential of Hf:HAp nanoparticles in tumor treatment, such as being used in a palliative treatment after lung surgical procedure. Photodynamic therapy (PDT) is one of the new clinical options by generating cytotoxic reactive oxygen species (ROS) to kill cancer cells. Unfortunately, the approach of PDT is usually limited to the treatment of systemic disease and deeper tumor, due to the limited tissue penetration depth of visible

49 CFR 173.474 - Quality control for construction of packaging.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Quality control for construction of packaging. 173...-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.474 Quality control for construction of packaging. Prior to the first use of any packaging for the shipment of Class 7...

21 CFR 173.140 - Esterase-lipase derived from Mucor miehei.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Esterase-lipase derived from Mucor miehei. 173.140... HUMAN CONSUMPTION Enzyme Preparations and Microorganisms § 173.140 Esterase-lipase derived from Mucor miehei. Esterase-lipase enzyme, consisting of enzyme derived from Mucor miehei var. Cooney et Emerson by...

49 CFR 173.159a - Exceptions for non-spillable batteries.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Exceptions for non-spillable batteries. 173.159a... Class 1 and Class 7 § 173.159a Exceptions for non-spillable batteries. (a) Exceptions for hazardous...-spillable batteries offered for transportation or transported in accordance with this section are subject to...

33 CFR 173.85 - Fees levied by the Coast Guard.

Science.gov (United States)

2010-07-01

.... 173.85 Section 173.85 Navigation and Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) BOATING SAFETY VESSEL NUMBERING AND CASUALTY AND ACCIDENT REPORTING Issue of Certificate of.... (b) Fees are payable by check or money-order made payable to the “U.S. Coast Guard”; by major credit...

49 CFR 173.172 - Aircraft hydraulic power unit fuel tank.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Aircraft hydraulic power unit fuel tank. 173.172... Class 1 and Class 7 § 173.172 Aircraft hydraulic power unit fuel tank. Aircraft hydraulic power unit fuel tanks containing a mixture of anhydrous hydrazine and monomethyl hydrazine (M86 fuel) and designed...

21 CFR 173.368 - Ozone.

Science.gov (United States)

2010-04-01

... CONSUMPTION (CONTINUED) SECONDARY DIRECT FOOD ADDITIVES PERMITTED IN FOOD FOR HUMAN CONSUMPTION Specific Usage Additives § 173.368 Ozone. Ozone (CAS Reg. No. 10028-15-6) may be safely used in the treatment, storage, and processing of foods, including meat and poultry (unless such use is precluded by standards of identity in 9...

49 CFR 173.403 - Definitions.

Science.gov (United States)

2010-10-01

... emitters and low toxicity alpha emitters or 0.04 Bq/cm2 for all other alpha emitters. Contamination exists... containers.” Graphite means, for the purposes of § 173.453, graphite with a boron equivalent content less... A2/g. Low toxicity alpha emitters means natural uranium; depleted uranium; natural thorium; uranium...

49 CFR 173.161 - Chemical kits and first aid kits.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Chemical kits and first aid kits. 173.161 Section... Class 7 § 173.161 Chemical kits and first aid kits. (a) Chemical kits and First aid kits must conform to... 10 kg. (b) Chemical kits and First aid kits are excepted from the specification packaging...

Sub-10 nm low current resistive switching behavior in hafnium oxide stack

Energy Technology Data Exchange (ETDEWEB)

Hou, Y., E-mail: houyi@pku.edu.cn, E-mail: lfliu@pku.edu.cn [Institute of Microelectronics, Peking University, 100871 Beijing (China); IMEC, Kapeldreef 75, B-3001 Heverlee (Belgium); Department of Physics and Astronomy, KU Leuven, Celestijnenlaan 200D, B-3001 Heverlee (Belgium); Celano, U.; Xu, Z.; Vandervorst, W. [IMEC, Kapeldreef 75, B-3001 Heverlee (Belgium); Department of Physics and Astronomy, KU Leuven, Celestijnenlaan 200D, B-3001 Heverlee (Belgium); Goux, L.; Fantini, A.; Degraeve, R.; Youssef, A.; Jurczak, M. [IMEC, Kapeldreef 75, B-3001 Heverlee (Belgium); Liu, L., E-mail: houyi@pku.edu.cn, E-mail: lfliu@pku.edu.cn; Cheng, Y.; Kang, J. [Institute of Microelectronics, Peking University, 100871 Beijing (China)

2016-03-21

In this letter, a tip-induced cell relying on the conductive atomic force microscope is proposed. It is verified as a referable replica of an integrated resistive random access memory (RRAM) device. On the basis of this cell, the functionality of sub-10 nm resistive switching is confirmed in hafnium oxide stack. Moreover, the low current switching behavior in the sub-10 nm dimension is found to be more pronounced than that of a 50 × 50 nm{sup 2} device. It shows better ON/OFF ratio and low leakage current. The enhanced memory performance is ascribed to a change in the shape of the conductive filament as the device dimensions are reduced to sub-10 nm. Therefore, device downscaling provides a promising approach for the resistance optimization that benefits the RRAM array design.

Separation of hafnium from zirconium in their tetrachloride solution in molten alkali metal chlorides

Energy Technology Data Exchange (ETDEWEB)

Salyulev, A B; Kudyakov, V Ya; Smirnov, M V; Moskalenko, N I [AN SSSR, Sverdlovsk. Inst. Ehlektrokhimii

1984-08-01

The coefficient of HfCl/sub 4/ and ZrCl/sub 4/ separation in the process of vapour sublimation from their solutions in molten NaCl, KCl, CsCl, NaCl-KCl and NaCl-CsCl equimolar mixtures is found to vary in the series from approximately 1.10 to approximately 1.22 and practically not to depend on the temperature (in the 600-910 deg) range and concentration (2-25 mol.% ZrCl/sub 4/+HfCl/sub 4/). HfCl/sub 4/ and ZrCl/sub 4/ are shown to form almost perfect solutions with each other, which in their turn form imperfect solutions with molten alkali metal chlorides, with the strength of hafnium complex chloride anions increasing higher than that of zirconium in the series from NaCl to CsCl.

Separation of hafnium from zirconium in their tetrachloride solution in molten alkali metal chlorides

International Nuclear Information System (INIS)

Salyulev, A.B.; Kudyakov, V.Ya.; Smirnov, M.V.; Moskalenko, N.I.

1984-01-01

The coefficient of HfCl 4 and ZrCl 4 separation in the process of vapour sublimation from their solutions in molten NaCl, KCl, CsCl, NaCl-KCl and NaCl-CsCl equimolar mixtures is found to vary in the series from approximately 1.10 to approximately 1.22 and practically not to depend on the temperature (in the 600-910 deg) range and concentration (2-25 mol.% ZrCl 4 +HfCl 4 ). HfCl 4 and ZrCl 4 are shown to form almost perfect solutions with each other, which in their turn form imperfect solutions with molten alkali metal chlorides, with the strength of hafnium complex chloride anions increasing higher than that of zirconium in the series from NaCl to CsCl

21 CFR 173.145 - Alpha-Galactosidase derived from Mortierella vinaceae var. raffinoseutilizer.

Science.gov (United States)

2010-04-01

... vinaceae var. raffinoseutilizer. 173.145 Section 173.145 Food and Drugs FOOD AND DRUG ADMINISTRATION... Alpha-Galactosidase derived from Mortierella vinaceae var. raffinoseutilizer. The food additive alpha-galactosidase and parent mycelial microorganism Mortierella vinaceae var. raffinoseutilizer may be safely used...

Density and surface tension of melts of zirconium and hafnium fluorides with lithium fluoride

International Nuclear Information System (INIS)

Katyshev, S.F.; Artemov, V.V.; Desyatnik, V.N.

1988-01-01

A study was conducted to determine the temperature dependence of the density and surface tension of melts of LiF-ZrF 4 and LiF-HfF 4 . Density and surface tension were determined by the method of maximum pressure in an argon bubble. On the basis of experimental data over the entire concentration range the molar volumes and their relative deviations from the additive molar volumes were calculated for 1100 0 K. The positive deviations of the molar volumes from additivity in the LiF-HfF 4 system (22.45%) were greater than in the LiF-ZrF 4 system (15.75%). This indicated that the reaction with lithium fluoride is intensified with the switch to the hafnium fluoride. Results also demonstrated that the fluorides are surface-active components in the molten mixtures

46 CFR 173.058 - Double bottom requirements.

Science.gov (United States)

2010-10-01

... PERTAINING TO VESSEL USE School Ships § 173.058 Double bottom requirements. Each new sailing school vessel... service must comply with the double bottom requirements in §§ 171.105 through 171.109, inclusive, of this...

Tribo-electrochemical characterization of hafnium multilayer systems deposited on nitride/vanadium nitride AISI 4140 steel

Science.gov (United States)

Mora, M.; Vera, E.; Aperador, W.

2016-02-01

In this work is presented the synergistic behaviour among corrosion/wear (tribocorrosion) of the multilayer coatings hafnium nitride/vanadium nitride [HfN/VN]n. The multilayers were deposited on AISI 4140 steel using the technique of physical vapor deposition PVD magnetron sputtering, the tests were performed using a pin-on-disk tribometer, which has an adapted potentiostat galvanostat with three-electrode electrochemical cell. Tribocorrosive parameters such as: Friction coefficient between the coating and the counter body (100 Cr6 steel ball); Polarization resistance by means of electrochemical impedance spectroscopy technique and corrosion rate by polarization curves were determined. It was observed an increase in the polarization resistance, a decrease in the corrosion rate and a low coefficient of friction in comparison with the substrate, due to an increase on the number of bilayers.

Tribo-electrochemical characterization of hafnium multilayer systems deposited on nitride/vanadium nitride AISI 4140 steel

International Nuclear Information System (INIS)

Mora, M; Vera, E; Aperador, W

2016-01-01

In this work is presented the synergistic behaviour among corrosion/wear (tribocorrosion) of the multilayer coatings hafnium nitride/vanadium nitride [HfN/VN]n. The multilayers were deposited on AISI 4140 steel using the technique of physical vapor deposition PVD magnetron sputtering, the tests were performed using a pin-on-disk tribometer, which has an adapted potentiostat galvanostat with three-electrode electrochemical cell. Tribocorrosive parameters such as: Friction coefficient between the coating and the counter body (100 Cr6 steel ball); Polarization resistance by means of electrochemical impedance spectroscopy technique and corrosion rate by polarization curves were determined. It was observed an increase in the polarization resistance, a decrease in the corrosion rate and a low coefficient of friction in comparison with the substrate, due to an increase on the number of bilayers. (paper)

Rapid screening of nuclear grade zirconium silicate without separation of hafnium from the bulk matrix

International Nuclear Information System (INIS)

Venkatesh, Manisha; Sharma, P.K.; Avhad, D.K.; Basu, H.; Singhal, R.K.; Reddy, A.V.R.

2014-01-01

Zirconium silicate, also zirconium orthosilicate, (ZrSiO 4 ) is a chemical compound, and occurs in nature as zircon, a silicate mineral. The concentration of Hafnium in nuclear grade Zirconium must be less than 0.2% w/w of Zr. In view of this it must be accurately chemically characterized before issuing a certification for export under non nuclear category. As the chemistry of Zr and Hf is similar, it is difficult to separate Hf by direct wet chemical method. During this work, concentration of Hf in zirconium silicate was measured by Field Portable X-ray Fluorescence (FPXRF) and results obtained were validated by using detailed chemical method. FPXRF spectrometry has become a common analytical technique for on-site screening and fast turnaround analysis of contaminant elements in environmental samples

Hafnium Films and Magnetic Shielding for TIME, A mm-Wavelength Spectrometer Array

Science.gov (United States)

Hunacek, J.; Bock, J.; Bradford, C. M.; Butler, V.; Chang, T.-C.; Cheng, Y.-T.; Cooray, A.; Crites, A.; Frez, C.; Hailey-Dunsheath, S.; Hoscheit, B.; Kim, D. W.; Li, C.-T.; Marrone, D.; Moncelsi, L.; Shirokoff, E.; Steinbach, B.; Sun, G.; Trumper, I.; Turner, A.; Uzgil, B.; Weber, A.; Zemcov, M.

2018-04-01

TIME is a mm-wavelength grating spectrometer array that will map fluctuations of the 157.7-μm emission line of singly ionized carbon ([CII]) during the epoch of reionization (redshift z ˜ 5-9). Sixty transition-edge sensor (TES) bolometers populate the output arc of each of the 32 spectrometers, for a total of 1920 detectors. Each bolometer consists of gold absorber on a ˜ 3 × 3 mm silicon nitride micro-mesh suspended near the corners by 1 × 1 × 500 μm silicon nitride legs targeting a photon-noise-dominated NEP ˜ 1 × 10^{-17} W/√{Hz} . Hafnium films are explored as a lower-T_c alternative to Ti (500 mK) for TIME TESs, allowing thicker support legs for improved yield. Hf T_c is shown to vary between 250 and 450 mK when varying the resident Ar pressure during deposition. Magnetic shielding designs and simulations are presented for the TIME first-stage SQUIDs. Total axial field suppression is predicted to be 5 × 10^7.

A spanish mineral of zirconium and hafnium. Separation of the two elements by liquid-liquid extraction, using tributyl phosphate as chelating agent

International Nuclear Information System (INIS)

Ruiz Sanchez, F.; Cruz Castillo, F. de la; Fernandez Cellini, R.

1962-01-01

The zirconium and Hafnium oxides are obtained from a Spanish mineral of zircon with an average contest of 55% in ZrO 2 -HfO 2 . An alkaline fusion to open the mineral, followed by a purification by crystallization as (Zr O-Hf O)Cl 2 H 2 O or as (Zr-Hf) (SO 4 ) 2 . 4H 2 O, is used. A discussion of the best experimental conditions for opening the mineral and of the purification method is made. (Author) 45 refs

19 CFR 173.5 - Review of entry covering household or personal effects.

Science.gov (United States)

2010-04-01

... 19 Customs Duties 2 2010-04-01 2010-04-01 false Review of entry covering household or personal effects. 173.5 Section 173.5 Customs Duties U.S. CUSTOMS AND BORDER PROTECTION, DEPARTMENT OF HOMELAND... authority to grant. Where the port director has no authority to grant the waiver, the application shall be...

21 CFR 173.395 - Trifluoromethane sulfonic acid.

Science.gov (United States)

2010-04-01

...) FOOD FOR HUMAN CONSUMPTION (CONTINUED) SECONDARY DIRECT FOOD ADDITIVES PERMITTED IN FOOD FOR HUMAN CONSUMPTION Specific Usage Additives § 173.395 Trifluoromethane sulfonic acid. Trifluoromethane sulfonic acid... acid) may safely be used in the production of cocoa butter substitute from palm oil (1-palmitoyl-2...

49 CFR 17.3 - What programs and activities of the Department are subject to these regulations?

Science.gov (United States)

2010-10-01

... 49 Transportation 1 2010-10-01 2010-10-01 false What programs and activities of the Department are subject to these regulations? 17.3 Section 17.3 Transportation Office of the Secretary of Transportation INTERGOVERNMENTAL REVIEW OF DEPARTMENT OF TRANSPORTATION PROGRAMS AND ACTIVITIES § 17.3 What programs and activities...

George de Hevesy (1885-1966). Discoverer of hafnium, founder of radioanalytical chemistry and X-ray fluorescence analysis and father of nuclear medicine

International Nuclear Information System (INIS)

Niese, Siegfried

2017-01-01

George de Hevesy known as discoverer of hafnium, founder of radioanalytical chemistry and X-ray fluorescence analysis and father of nuclear medicine has done important research work in inorganic, physical and radioanalytical and physiological chemistry as well as in geochemistry, radiation biology and medicine. When he must flee for political reasons from a country he must change his colleagues, his equipments, and the topic of his work. It is extremely surprising that he could receive important results under such circumstances even at an advanced age. (author)

49 CFR 173.426 - Excepted packages for articles containing natural uranium or thorium.

Science.gov (United States)

2010-10-01

... outer surface of the uranium or thorium is enclosed in an inactive sheath made of metal or other durable... uranium or thorium. 173.426 Section 173.426 Transportation Other Regulations Relating to Transportation....426 Excepted packages for articles containing natural uranium or thorium. A manufactured article in...

49 CFR 173.340 - Tear gas devices.

Science.gov (United States)

2010-10-01

... SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.340 Tear gas devices. (a) Packagings for...) Tear gas devices may not be assembled with, or packed in the same packaging with, mechanically- or manually-operated firing, igniting, bursting, or other functioning elements unless of a type and design...

Silicon-doped hafnium oxide anti-ferroelectric thin films for energy storage

Science.gov (United States)

Ali, Faizan; Liu, Xiaohua; Zhou, Dayu; Yang, Xirui; Xu, Jin; Schenk, Tony; Müller, Johannes; Schroeder, Uwe; Cao, Fei; Dong, Xianlin

2017-10-01

Motivated by the development of ultracompact electronic devices as miniaturized energy autonomous systems, great research efforts have been expended in recent years to develop various types of nano-structural energy storage components. The electrostatic capacitors characterized by high power density are competitive; however, their implementation in practical devices is limited by the low intrinsic energy storage density (ESD) of linear dielectrics like Al2O3. In this work, a detailed experimental investigation of energy storage properties is presented for 10 nm thick silicon-doped hafnium oxide anti-ferroelectric thin films. Owing to high field induced polarization and slim double hysteresis, an extremely large ESD value of 61.2 J/cm3 is achieved at 4.5 MV/cm with a high efficiency of ˜65%. In addition, the ESD and the efficiency exhibit robust thermal stability in 210-400 K temperature range and an excellent endurance up to 109 times of charge/discharge cycling at a very high electric field of 4.0 MV/cm. The superior energy storage performance together with mature technology of integration into 3-D arrays suggests great promise for this recently discovered anti-ferroelectric material to replace the currently adopted Al2O3 in fabrication of nano-structural supercapacitors.

Tuning the magnetic properties of pure hafnium by high pressure torsion

International Nuclear Information System (INIS)

Cepeda-Jiménez, C.M.; Beltrán, J.I.; Hernando, A.; García, M.A.; Ynduráin, F.; Zhilyaev, A.; Pérez-Prado, M.T.

2017-01-01

This work demonstrates that room temperature (RT) ferromagnetism might be triggered in pure hafnium (Hf), a classic paramagnet, by severe plastic deformation (SPD) via high pressure torsion (HPT). The origin of this phenomenon is elucidated by a combined approach including density functional theory (DFT) calculations and transmission electron microscopy (TEM). In particular, it is shown that the elastic lattice distorsions induced in pure Hf as a consequence of grain refinement down to the nanocrystalline regime by HPT lead to the development of a new monoclinic crystalline structure that exhibits a spontaneous magnetization at RT. DFT calculations are utilized to prove that local stretching of the original pure Hf hexagonal close packed (hcp) lattice along specific pyramidal directions, due to the presence of internal stresses in the deformed nanostructure, may give rise to the emergence of the monoclinic phase, which is endowed with a net magnetic moment. An excellent agreement is found between DFT calculations and experimental TEM observations, which provide a first evidence of the presence of the pure Hf monoclinic crystal lattice. This work shows that SPD may constitute a viable, yet widely unexplored, strategy to tune the magnetic properties and, in particular, to induce RT ferromagnetism in bulk non-magnetic metals.

40 CFR 98.173 - Calculating GHG emissions.

Science.gov (United States)

2010-07-01

... (CONTINUED) MANDATORY GREENHOUSE GAS REPORTING Iron and Steel Production § 98.173 Calculating GHG emissions... for the process as specified in paragraphs (b)(1)(i) through (b)(1)(vii) of this section. The... the gaseous fuel (kg/kg-mole). MVC = Molar volume conversion factor (849.5 scf per kg-mole at standard...

Characterization of hafnium oxide resistive memory layers deposited on copper by atomic layer deposition

Energy Technology Data Exchange (ETDEWEB)

Briggs, B.D.; Bishop, S.M. [SUNY College of Nanoscale Science and Engineering, 255 Fuller Road, Albany, NY 12203 (United States); Leedy, K.D. [Air Force Research Laboratory, 2241 Avionics Circle, Wright Patterson Air Force Base, Dayton, OH 45433 (United States); Cady, N.C., E-mail: ncady@albany.edu [SUNY College of Nanoscale Science and Engineering, 255 Fuller Road, Albany, NY 12203 (United States)

2014-07-01

Hafnium oxide-based resistive memory devices have been fabricated on copper bottom electrodes. The HfO{sub x} active layers in these devices were deposited by atomic layer deposition (ALD) at 250 °C with tetrakis(dimethylamido)hafnium(IV) as the metal precursor and an O{sub 2} plasma as the reactant. Depth profiles of the HfO{sub x} by X-ray photoelectron spectroscopy and secondary ion mass spectroscopy revealed a copper concentration on the order of five atomic percent throughout the HfO{sub x} film. In addition to the Cu doped HfO{sub x}, a thin layer (20 nm) of Cu{sub x}O is present at the surface. This surface layer is believed to have formed during the ALD process, and greatly complicates the analysis of the switching mechanism. The resistive memory structures fabricated from the ALD HfO{sub x} exhibited non-polar resistive switching, independent of the top metal electrode (Ni, Pt, Al, Au). Resistive switching current voltage (I–V) curves were analyzed using Schottky emission and ionic hopping models to gain insight into the physical mechanisms underpinning the device behavior. During the forming process it was determined that, at voltages in excess of 2.5 V, an ionic hopping model is in good agreement with the I–V data. The extracted ion hopping distance ∼ 4 Å was within the range of interatomic spacing of HfO{sub 2} during the forming process consistent with ionic motion of Cu{sup 2+} ions. Lastly the on state I–V data was dominated at larger voltages by Schottky emission with an estimated barrier height of ∼ 0.5 eV and a refractive index of 2.59. The consequence of the Schottky emission analysis indicates the on state resistance to be a product of a Pt/Cu{sub 2}O/Cu filament(s)/Cu{sub 2}O/Cu structure. - Highlights: • HfO{sub 2} was grown via atomic layer deposition at 250 and 100 °C on Cu substrates. • A Cu{sub 2}O surface layer and Cu doping were observed in post-deposition of HfO{sub 2}. • Resistive memory devices were fabricated and

Thermodynamic and kinetic studies in the systems alkali chloride-zinconium (or hafnium) tetrachloride: Part I. Vapour pressure measurements over hexachloro compounds and use of vapour pressure data in fractional decomposition

International Nuclear Information System (INIS)

Ray, H.S.; Bhat, B.G.; Reddy, G.S.; Biswas, A.K.

1978-01-01

A molten tin isoteniscope has been used to measure the vapour pressures over ZrCl 4 , HfCl 4 and the hexachlore zirconates (M 2 ZrCl 6 ) and the hexachloro hafnates (M 2 HfCl 6 ) of four alkali metals (M = Na,K,Rb,Cs). The method of preparation of these compounds and the effect of small amounts of residual alkali chlorides on the their vapour pressure are discussed. The pressure-temperature plots are examined in the light of some theoretical postulates. A scheme for separation of hafnium from zirconoium by multistage fractional decomposition of the hexachlore compounds of any alkali metal is described. The scheme, which is analogous to rectification in liquid-vapour systems, employs a countercurrent flow of Zr(Hf)Cl 4 in a gas stream and a moving bed of alkali chlorides. The separation is based on the difference in the dissociation equilibrium for zirconium and hafnium compounds. Stage calculations for such a scheme and the main conclusions of a computational work are presented. (author)

30 CFR 206.173 - How do I calculate the alternative methodology for dual accounting?

Science.gov (United States)

2010-07-01

... measured at facility measurement points whose quality exceeds 1,000 Btu/cf are subject to dual accounting... for dual accounting? 206.173 Section 206.173 Mineral Resources MINERALS MANAGEMENT SERVICE, DEPARTMENT... the alternative methodology for dual accounting? (a) Electing a dual accounting method. (1) If you are...

49 CFR 173.7 - Government operations and materials.

Science.gov (United States)

2010-10-01

...) Determining the airworthiness and directing maintenance of the aircraft; and (3) Dispatching the aircraft... REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS General § 173.7 Government operations and materials. (a) Hazardous... regulations in this subchapter or in packagings of equal or greater strength and efficiency as certified by...

Metallorganic chemical vapor deposition and atomic layer deposition approaches for the growth of hafnium-based thin films from dialkylamide precursors for advanced CMOS gate stack applications

Science.gov (United States)

Consiglio, Steven P.

To continue the rapid progress of the semiconductor industry as described by Moore's Law, the feasibility of new material systems for front end of the line (FEOL) process technologies needs to be investigated, since the currently employed polysilicon/SiO2-based transistor system is reaching its fundamental scaling limits. Revolutionary breakthroughs in complementary-metal-oxide-semiconductor (CMOS) technology were recently announced by Intel Corporation and International Business Machines Corporation (IBM), with both organizations revealing significant progress in the implementation of hafnium-based high-k dielectrics along with metal gates. This announcement was heralded by Gordon Moore as "...the biggest change in transistor technology since the introduction of polysilicon gate MOS transistors in the late 1960s." Accordingly, the study described herein focuses on the growth of Hf-based dielectrics and Hf-based metal gates using chemical vapor-based deposition methods, specifically metallorganic chemical vapor deposition (MOCVD) and atomic layer deposition (ALD). A family of Hf source complexes that has received much attention recently due to their desirable properties for implementation in wafer scale manufacturing is the Hf dialkylamide precursors. These precursors are room temperature liquids and possess sufficient volatility and desirable decomposition characteristics for both MOCVD and ALD processing. Another benefit of using these sources is the existence of chemically compatible Si dialkylamide sources as co-precursors for use in Hf silicate growth. The first part of this study investigates properties of MOCVD-deposited HfO2 and HfSixOy using dimethylamido Hf and Si precursor sources using a customized MOCVD reactor. The second part of this study involves a study of wet and dry surface pre-treatments for ALD growth of HfO2 using tetrakis(ethylmethylamido)hafnium in a wafer scale manufacturing environment. The third part of this study is an investigation of

Recoil Induced Room Temperature Stable Frenkel Pairs in a-Hafnium Upon Thermal Neutron Capture

Science.gov (United States)

Butz, Tilman; Das, Satyendra K.; Dey, Chandi C.; Ghoshal, Shamik

2013-11-01

Ultrapure hafnium metal (110 ppm zirconium) was neutron activated with a thermal neutron flux of 6:6 · 1012 cm-2s-1 in order to obtain 181Hf for subsequent time differential perturbed angular correlation (TDPAC) experiments using the nuclear probe 181Hf(β-) 181Ta. Apart from the expected nuclear quadrupole interaction (NQI) signal for a hexagonal close-packed (hcp) metal, three further discrete NQIs were observed with a few percent fraction each. The TDPAC spectra were recorded for up to 11 half lives with extreme statistical accuracy. The fitted parameters vary slightly within the temperature range between 248 K and 373 K. The signals corresponding to the three additional sites completely disappear after `annealing' at 453 K for one minute. Based on the symmetry of the additional NQIs and their temperature dependencies, they are tentatively attributed to Frenkel pairs produced by recoil due to the emission of a prompt 5:694 MeV -ray following thermal neutron capture and reported by the nuclear probe in three different positions. These Frenkel pairs are stable up to at least 373 K.

46 CFR 173.007 - Location of the hook load.

Science.gov (United States)

2010-10-01

... PERTAINING TO VESSEL USE Lifting § 173.007 Location of the hook load. When doing the calculations required in this subpart, the hook load must be considered to be located at the head of the crane. ...

The energy landscape of glassy dynamics on the amorphous hafnium diboride surface

Science.gov (United States)

Nguyen, Duc; Mallek, Justin; Cloud, Andrew N.; Abelson, John R.; Girolami, Gregory S.; Lyding, Joseph; Gruebele, Martin

2014-11-01

Direct visualization of the dynamics of structural glasses and amorphous solids on the sub-nanometer scale provides rich information unavailable from bulk or conventional single molecule techniques. We study the surface of hafnium diboride, a conductive ultrahigh temperature ceramic material that can be grown in amorphous films. Our scanning tunneling movies have a second-to-hour dynamic range and single-point current measurements extend that to the millisecond-to-minute time scale. On the a-HfB2 glass surface, two-state hopping of 1-2 nm diameter cooperatively rearranging regions or "clusters" occurs from sub-milliseconds to hours. We characterize individual clusters in detail through high-resolution (single cluster vertical displacements, we can reconstruct the local free energy landscape of individual clusters, complete with activation barrier height, a reaction coordinate in nanometers, and the shape of the free energy landscape basins between which hopping occurs. The experimental images are consistent with the compact shape of α-relaxors predicted by random first order transition theory, whereas the rapid hopping rate, even taking less confined motion at the surface into account, is consistent with β-relaxations. We make a proposal of how "mixed" features can show up in surface dynamics of glasses.

About the structure and stability of complex carbonates of thorium (IV), cerium (IV), zirconium (IV), hafnium (IV)

International Nuclear Information System (INIS)

Dervin, Jacqueline

1972-01-01

This research thesis addressed the study of complex carbonates of cations of metals belonging to the IV A column, i.e. thorium (IV), zirconium (IV), hafnium (IV), and also cerium (IV) and uranium (VI), and more particularly focused on ionic compounds formed in solution, and also on the influence of concentration and nature of cations on stability and nature of the formed solid. The author first presents methods used in this study, discusses their precision and scope of validity. She reports the study of the formation of different complex ions which have been highlighted in solution, and the determination of their formation constants. She reports the preparation and study of the stability domain of solid complexes. The next part reports the use of thermogravimetric analysis, IR spectrometry, and crystallography for the structural study of these compounds

Tank 241-B-108, cores 172 and 173 analytical results for the final report

Energy Technology Data Exchange (ETDEWEB)

Nuzum, J.L., Fluoro Daniel Hanford

1997-03-04

The Data Summary Table (Table 3) included in this report compiles analytical results in compliance with all applicable DQOS. Liquid subsamples that were prepared for analysis by an acid adjustment of the direct subsample are indicated by a `D` in the A column in Table 3. Solid subsamples that were prepared for analysis by performing a fusion digest are indicated by an `F` in the A column in Table 3. Solid subsamples that were prepared for analysis by performing a water digest are indicated by a I.wl. or an `I` in the A column of Table 3. Due to poor precision and accuracy in original analysis of both Lower Half Segment 2 of Core 173 and the core composite of Core 173, fusion and water digests were performed for a second time. Precision and accuracy improved with the repreparation of Core 173 Composite. Analyses with the repreparation of Lower Half Segment 2 of Core 173 did not show improvement and suggest sample heterogeneity. Results from both preparations are included in Table 3.

21 CFR 173.21 - Perfluorinated ion exchange membranes.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Perfluorinated ion exchange membranes. 173.21... ion exchange membranes. Substances identified in paragraph (a) of this section may be safely used as ion exchange membranes intended for use in the treatment of bulk quantities of liquid food under the...

33 CFR 173.27 - Numbers: Display; size; color.

Science.gov (United States)

2010-07-01

... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Numbers: Display; size; color...: Display; size; color. (a) Each number required by § 173.15 must: (1) Be painted on or permanently attached...; (3) Contrast with the color of the background and be distinctly visible and legible; (4) Have spaces...

21 CFR 173.320 - Chemicals for controlling microorganisms in cane-sugar and beet-sugar mills.

Science.gov (United States)

2010-04-01

...-sugar and beet-sugar mills. 173.320 Section 173.320 Food and Drugs FOOD AND DRUG ADMINISTRATION... controlling microorganisms in cane-sugar and beet-sugar mills. Agents for controlling microorganisms in cane-sugar and beet-sugar mills may be safely used in accordance with the following conditions: (a) They are...

49 CFR 173.60 - General packaging requirements for explosives.

Science.gov (United States)

2010-10-01

... explosives contained in the package, so that neither interaction between the explosives and the packaging... 49 Transportation 2 2010-10-01 2010-10-01 false General packaging requirements for explosives. 173...-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Definitions, Classification and Packaging for Class 1...

14 CFR 135.173 - Airborne thunderstorm detection equipment requirements.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 3 2010-01-01 2010-01-01 false Airborne thunderstorm detection equipment... Aircraft and Equipment § 135.173 Airborne thunderstorm detection equipment requirements. (a) No person may... the aircraft is equipped with either approved thunderstorm detection equipment or approved airborne...

49 CFR 173.466 - Additional tests for Type A packagings designed for liquids and gases.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Additional tests for Type A packagings designed...) Materials § 173.466 Additional tests for Type A packagings designed for liquids and gases. (a) In addition to the tests prescribed in § 173.465, Type A packagings designed for liquids and gases must be...

A search for long-lived radionuclides produced by fast-neutron irradiations of copper, silver, europium, terbium, and hafnium

International Nuclear Information System (INIS)

Meadows, J.W.; Smith, D.L.; Ikeda, Y.; Konno, C.

1990-01-01

Identical sample packets, each containing samples of elemental copper, silver, europium, terbium, and hafnium, as well as titanium, iron and nickel as dosimeters, have been irradiated in three distinct accelerator neutron fields (at Argonne National Laboratory and Los Alamos National Laboratory in the U.S.A., and Japan Atomic Energy Research Institute, Tokai, Japan) as part of an interlaboratory research collaboration to search for the production of long-lived radionuclides for fusion waste disposal applications. This paper is a progress report on this project. To date, we have detected the following activities, and have obtained preliminary experimental cross section values for several of these: Ag-106m,108m,110m; Eu-150m,152g,154; Tb-158,160; and Hf-175,178m2,179m2,181. (author). 11 refs, 1 fig., 4 tabs

25 CFR 1000.173 - How does a newly selected Tribe/Consortium initiate the negotiation phase?

Science.gov (United States)

2010-04-01

... 25 Indians 2 2010-04-01 2010-04-01 false How does a newly selected Tribe/Consortium initiate the negotiation phase? 1000.173 Section 1000.173 Indians OFFICE OF THE ASSISTANT SECRETARY, INDIAN AFFAIRS, DEPARTMENT OF THE INTERIOR ANNUAL FUNDING AGREEMENTS UNDER THE TRIBAL SELF-GOVERNMENT ACT AMENDMENTS TO THE INDIAN SELF-DETERMINATION AND EDUCATIO...

49 CFR 173.312 - Requirements for shipment of MEGCs.

Science.gov (United States)

2010-10-01

...-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Gases; Preparation and Packaging § 173.312 Requirements... MEGC's structural or service equipment may be affected. (4) No person may fill or offer for... requalification due date. (5) Prior to filling and offering a MEGC for transportation, the MEGC's structural and...

Ferroelectric transistors with monolayer molybdenum disulfide and ultra-thin aluminum-doped hafnium oxide

Science.gov (United States)

Yap, Wui Chung; Jiang, Hao; Liu, Jialun; Xia, Qiangfei; Zhu, Wenjuan

2017-07-01

In this letter, we demonstrate ferroelectric memory devices with monolayer molybdenum disulfide (MoS2) as the channel material and aluminum (Al)-doped hafnium oxide (HfO2) as the ferroelectric gate dielectric. Metal-ferroelectric-metal capacitors with 16 nm thick Al-doped HfO2 are fabricated, and a remnant polarization of 3 μC/cm2 under a program/erase voltage of 5 V is observed. The capability of potential 10 years data retention was estimated using extrapolation of the experimental data. Ferroelectric transistors based on embedded ferroelectric HfO2 and MoS2 grown by chemical vapor deposition are fabricated. Clockwise hysteresis is observed at low program/erase voltages due to slow bulk traps located near the 2D/dielectric interface, while counterclockwise hysteresis is observed at high program/erase voltages due to ferroelectric polarization. In addition, the endurances of the devices are tested, and the effects associated with ferroelectric materials, such as the wake-up effect and polarization fatigue, are observed. Reliable writing/reading in MoS2/Al-doped HfO2 ferroelectric transistors over 2 × 104 cycles is achieved. This research can potentially lead to advances of two-dimensional (2D) materials in low-power logic and memory applications.

49 CFR 173.306 - Limited quantities of compressed gases.

Science.gov (United States)

2010-10-01

... container must be weighed and leak tested. The leak detection equipment must be sufficiently sensitive to... Section 173.306 Transportation Other Regulations Relating to Transportation PIPELINE AND HAZARDOUS... softening provided that it does not leak. (vi) As an alternative to the hot water bath test in paragraph (a...

Tumor vessel normalization by the PI3K inhibitor HS-173 enhances drug delivery.

Science.gov (United States)

Kim, Soo Jung; Jung, Kyung Hee; Son, Mi Kwon; Park, Jung Hee; Yan, Hong Hua; Fang, Zhenghuan; Kang, Yeo Wool; Han, Boreum; Lim, Joo Han; Hong, Soon-Sun

2017-09-10

Tumor vessels are leaky and immature, which causes poor oxygen and nutrient supply to tumor vessels and results in cancer cell metastasis to distant organs. This instability of tumor blood vessels also makes it difficult for anticancer drugs to penetrate and reach tumors. Numerous tumor vessel normalization approaches have been investigated for improving drug delivery into tumors. In this study, we investigated whether phosphoinositide 3-kinase (PI3K) inhibitors are able to improve vascular structure and function over the prolonged period necessary to achieve effective vessel normalization. The PI3K inhibitors, HS-173 and BEZ235 potently suppressed tumor growth and hypoxia, and increased tumor apoptosis in animal models. PI3K inhibitors also induced a regular, flat monolayer of endothelial cells (ECs) in vessels, improving stability of vessel structure, and normalized tumor vessels by increasing vascular maturity, pericyte coverage, basement membrane thickness, and tight-junctions. These effects resulted in a decrease in tumor vessel tortuosity and vessel thinning, and improved vessel function and blood flow. The tumor vessel stabilization effect of the PI3K inhibitor HS-173 also decreased the number of metastatic lung nodules in vivo metastasis model. Furthermore, HS-173 improved the delivery of doxorubicin into the tumor region, enhancing its anticancer effects. Mechanistic studies suggested that PI3K inhibitor HS-173-induced vessel normalization reflected changes in endothelial Notch signaling. Taken together, our findings indicate that vessel normalization by PI3K inhibitors restrained tumor growth and metastasis while improving chemotherapy by enhancing drug delivery into the tumor, suggesting that HS-173 may have a therapeutic value as an enhancer or an anticancer drug. Copyright © 2017 Elsevier B.V. All rights reserved.

49 CFR 173.418 - Authorized packages-pyrophoric Class 7 (radioactive) materials.

Science.gov (United States)

2010-10-01

... must not be fissile unless excepted by § 173.453; (b) Contained in sealed and corrosion resistant receptacles with positive closures (friction or slip-fit covers or stoppers are not authorized); (c) Free of...

49 CFR 173.428 - Empty Class 7 (radioactive) materials packaging.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Empty Class 7 (radioactive) materials packaging... SHIPPERS-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.428 Empty Class 7 (radioactive) materials packaging. A packaging which previously contained Class 7 (radioactive...

46 CFR 173.025 - Additional intact stability standards: Counterballasted vessels.

Science.gov (United States)

2010-10-01

...) SUBDIVISION AND STABILITY SPECIAL RULES PERTAINING TO VESSEL USE Lifting § 173.025 Additional intact stability standards: Counterballasted vessels. (a) Each vessel equipped to counterballast while lifting must be shown... loading and operation and at each combination of hook load and crane radius. (b) When doing the...

IER-297 CED-2: Final Design for Thermal/Epithermal eXperiments with Jemima Plates with Polyethylene and Hafnium

Energy Technology Data Exchange (ETDEWEB)

Nelson, A. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Percher, C. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Zywiec, W. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Heinrichs, D. P. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2018-01-11

This report presents the final design (CED-2) for IER-297, and focuses on 15 critical configurations using highly enriched uranium (HEU) Jemima plates moderated by polyethylene with and without hafnium diluent. The goal of the U.S. Nuclear Criticality Safety Program’s Thermal/Epithermal eXperiments (TEX) is to design and conduct new critical experiments to address high priority nuclear data needs from the nuclear criticality safety and nuclear data communities, with special emphasis on intermediate energy (0.625 eV – 100 keV) assemblies that can be easily modified to include various high priority diluent materials. The TEX (IER 184) CED-1 Report [1], completed in 2012, demonstrated the feasibility of meeting the TEX goals with two existing NCSP fissile assets, plutonium Zero Power Physics Reactor (ZPPR) plates and highly enriched uranium (HEU) Jemima plates. The first set of TEX experiments will focus on using the plutonium ZPPR plates with polyethylene moderator and tantalum diluents.

49 CFR 173.164 - Mercury (metallic and articles containing mercury).

Science.gov (United States)

2010-10-01

... ounces) of mercury per package; (iv) Tubes which are completely jacketed in sealed leakproof metal cases... 49 Transportation 2 2010-10-01 2010-10-01 false Mercury (metallic and articles containing mercury... Than Class 1 and Class 7 § 173.164 Mercury (metallic and articles containing mercury). (a) For...

21 CFR 173.315 - Chemicals used in washing or to assist in the peeling of fruits and vegetables.

Science.gov (United States)

2010-04-01

... peeling of fruits and vegetables. 173.315 Section 173.315 Food and Drugs FOOD AND DRUG ADMINISTRATION... used in washing or to assist in the peeling of fruits and vegetables. Chemicals may be safely used to wash or to assist in the peeling of fruits and vegetables in accordance with the following conditions...

Improved DC performance of AlGaN/GaN high electron mobility transistors using hafnium oxide for surface passivation

International Nuclear Information System (INIS)

Liu, Chang; Chor, Eng Fong; Tan, Leng Seow

2007-01-01

Improved DC performance of AlGaN/GaN high electron mobility transistors (HEMTs) have been demonstrated using reactive-sputtered hafnium oxide (HfO 2 ) thin film as the surface passivation layer. Hall data indicate a significant increase in the product of sheet carrier concentration (n s ) and electron mobility (μ n ) in the HfO 2 -passivated HEMTs, compared to the unpassivated HEMTs. This improvement in electron carrier characteristics gives rise to a 22% higher I Dmax and an 18% higher g mmax in HEMTs with HfO 2 passivation relative to the unpassivated devices. On the other hand, I gleak of the HEMTs decreases by nearly one order of magnitude when HfO 2 passivation is applied. In addition, drain current is measured in the subthreshold regime. Compared to the unpassivated HEMTs, HfO 2 -passivated HEMTs exhibit a much smaller off-state I D , indicating better turn-off characteristics

Protective coatings of hafnium dioxide by atomic layer deposition for microelectromechanical systems applications

Energy Technology Data Exchange (ETDEWEB)

Berdova, Maria, E-mail: maria.berdova@aalto.fi [Aalto University, Department of Materials Science and Engineering, 02150, Espoo (Finland); Wiemer, Claudia; Lamperti, Alessio; Tallarida, Grazia; Cianci, Elena [Laboratorio MDM, IMM CNR, Via C. Olivetti 2, 20864, Agrate Brianza, MB (Italy); Lamagna, Luca; Losa, Stefano; Rossini, Silvia; Somaschini, Roberto; Gioveni, Salvatore [STMicroelectronics, Via C. Olivetti 2, 20864, Agrate Brianza, MB (Italy); Fanciulli, Marco [Laboratorio MDM, IMM CNR, Via C. Olivetti 2, 20864, Agrate Brianza, MB (Italy); Università degli studi di Milano Bicocca, Dipartimento di Scienza dei Materiali, 20126, Milano (Italy); Franssila, Sami, E-mail: sami.franssila@aalto.fi [Aalto University, Department of Materials Science and Engineering, 02150, Espoo (Finland)

2016-04-15

Graphical abstract: - Highlights: • Atomic layer deposition of HfO{sub 2} from (CpMe){sub 2}Hf(OMe)Me or Hf(NMeEt){sub 4} and ozone for potential applications in microelectromechanical systems. • ALD HfO{sub 2} protects aluminum substrates from degradation in moist environment and at the same time retains good reflectance properties of the underlying material. • The resistance of hafnium dioxide to moist environment is independent of chosen precursors. - Abstract: This work presents the investigation of HfO{sub 2} deposited by atomic layer deposition (ALD) from either HfD-CO4 or TEMAHf and ozone for microelectromechanical systems (MEMS) applications, in particular, for environmental protection of aluminum micromirrors. This work shows that HfO{sub 2} films successfully protect aluminum in moist environment and at the same time retain good reflectance properties of underlying material. In our experimental work, the chemical composition, crystal structure, electronic density and roughness of HfO{sub 2} films remained the same after one week of humidity treatment (relative humidity of 85%, 85 °C). The reflectance properties underwent only minor changes. The observed shift in reflectance was only from 80–90% to 76–85% in 400–800 nm spectral range when coated with ALD HfO{sub 2} films grown with Hf(NMeEt){sub 4} and no shift (remained in the range of 68–83%) for films grown from (CpMe){sub 2}Hf(OMe)Me.

49 CFR 173.221 - Polymeric beads, expandable and Plastic molding compound.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Polymeric beads, expandable and Plastic molding... Than Class 1 and Class 7 § 173.221 Polymeric beads, expandable and Plastic molding compound. (a) Non-bulk shipments of Polymeric beads (or granules), expandable, evolving flammable vapor and Plastic...

HS-173, a Novel PI3K Inhibitor, Attenuates the Activation of Hepatic Stellate Cells in Liver Fibrosis

Science.gov (United States)

Son, Mi Kwon; Ryu, Ye-Lim; Jung, Kyung Hee; Lee, Hyunseung; Lee, Hee Seung; Yan, Hong Hua; Park, Heon Joo; Ryu, Ji-Kan; Suh, Jun–Kyu; Hong, Sungwoo; Hong, Soon-Sun

2013-01-01

Hepatic stellate cells (HSCs) are the primary source of matrix components in liver disease such as fibrosis. Phosphatidylinositol 3-kinase (PI3K) signaling in HSCs has been shown to induce fibrogenesis. In this study, we evaluated the anti-fibrotic activity of a novel imidazopyridine analogue (HS-173) in human HSCs as well as mouse liver fibrosis. HS-173 strongly suppressed the growth and proliferation of HSCs and induced the arrest at the G2/M phase and apoptosis in HSCs. Furthermore, it reduced the expression of extracellular matrix components such as collagen type I, which was confirmed by an in vivo study. We also observed that HS-173 blocked the PI3K/Akt signaling pathway in vitro and in vivo. Taken together, HS-173 suppressed fibrotic responses such as cell proliferation and collagen synthesis by blocking PI3K/Akt signaling. Therefore, we suggest that this compound may be an effective therapeutic agent for ameliorating liver fibrosis through the inhibition of PI3K signaling. PMID:24326778

Efficient UV-emitting X-ray phosphors: octahedral Zr(PO4)6 luminescence centers in potassium hafnium-zirconium phosphates K2Hf1-xZrx(PO4)2 and KHf2(1-x)Zr2x(PO4)3

International Nuclear Information System (INIS)

Torardi, C.C.; Miao, C.R.; Li, J.

2003-01-01

Potassium hafnium-zirconium phosphates, K 2 Hf 1-x Zr x (PO 4 ) 2 and KHf 2(1-x) Zr 2x (PO 4 ) 3 , are broad-band UV-emitting phosphors. At room temperature, they have emission peak maxima at approximately 322 and 305 nm, respectively, under 30 kV peak molybdenum X-ray excitation. Both phosphors demonstrate luminescence efficiencies that make them up to ∼60% as bright as commercially available CaWO 4 Hi-Plus. The solid-state and flux synthesis conditions, and X-ray excited UV luminescence of these two phosphors are discussed. Even though the two compounds have different atomic structures, they contain zirconium in the same active luminescence environment as that found in highly efficient UV-emitting BaHf 1-x Zr x (PO 4 ) 2 . All the three materials have hafnium and zirconium in octahedral coordination via oxygen-atom corner sharing with six separate PO 4 tetrahedra. This octahedral Zr(PO 4 ) 6 moiety appears to be an important structural element for efficient X-ray excited luminescence, as are the edge-sharing octahedral TaO 6 chains for tantalate emission

49 CFR 173.33 - Hazardous materials in cargo tank motor vehicles.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hazardous materials in cargo tank motor vehicles... Transportation § 173.33 Hazardous materials in cargo tank motor vehicles. (a) General requirements. (1) No person may offer or accept a hazardous material for transportation in a cargo tank motor vehicle except as...

49 CFR 173.195 - Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution).

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Hydrogen cyanide, anhydrous, stabilized... Hazardous Materials Other Than Class 1 and Class 7 § 173.195 Hydrogen cyanide, anhydrous, stabilized (hydrocyanic acid, aqueous solution). (a) Hydrogen cyanide, anhydrous, stabilized, must be packed in...

The kinase domain residue serine 173 of Schizosaccharomyces pombe Chk1 kinase is critical for the response to DNA replication stress

Directory of Open Access Journals (Sweden)

Naomi Coulton

2017-12-01

Full Text Available While mammalian Chk1 kinase regulates replication origins, safeguards fork integrity and promotes fork progression, yeast Chk1 acts only in G1 and G2. We report here that the mutation of serine 173 (S173A in the kinase domain of fission yeast Chk1 abolishes the G1-M and S-M checkpoints with little impact on the G2-M arrest. This separation-of-function mutation strongly reduces the Rad3-dependent phosphorylation of Chk1 at serine 345 during logarithmic growth, but not when cells experience exogenous DNA damage. Loss of S173 lowers the restrictive temperature of a catalytic DNA polymerase epsilon mutant (cdc20.M10 and is epistatic with a mutation in DNA polymerase delta (cdc6.23 when DNA is alkylated by methyl-methanesulfate (MMS. The chk1-S173A allele is uniquely sensitive to high MMS concentrations where it displays a partial checkpoint defect. A complete checkpoint defect occurs only when DNA replication forks break in cells without the intra-S phase checkpoint kinase Cds1. Chk1-S173A is also unable to block mitosis when the G1 transcription factor Cdc10 (cdc10.V50 is impaired. We conclude that serine 173, which is equivalent to lysine 166 in the activation loop of human Chk1, is only critical in DNA polymerase mutants or when forks collapse in the absence of Cds1.

49 CFR 173.477 - Approval of packagings containing greater than 0.1 kg of non-fissile or fissile-excepted uranium...

Science.gov (United States)

2010-10-01

... kg of non-fissile or fissile-excepted uranium hexafluoride. 173.477 Section 173.477 Transportation... non-fissile or fissile-excepted uranium hexafluoride. (a) Each offeror of a package containing more than 0.1 kg of uranium hexafluoride must maintain on file for at least one year after the latest...

49 CFR 173.150 - Exceptions for Class 3 (flammable and combustible liquids).

Science.gov (United States)

2010-10-01

... HAZARDOUS MATERIALS SAFETY ADMINISTRATION, DEPARTMENT OF TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS... § 173.156. (d) Alcoholic beverages. An alcoholic beverage (wine and distilled spirits as defined in 27...-on baggage; or (3) Is a Packing Group III alcoholic beverage in a packaging of 250 L (66 gallons) or...

Recovery of metal chlorides from their complexes by molten salt displacement

International Nuclear Information System (INIS)

McLaughlin, D.F.; Stoltz, R.A.

1989-01-01

This patent describes a process for recovering zirconium or hafnium chloride from a complex of zirconium or hafnium tetrachloride and phosphorus oxychloride. The process comprising: introducing liquid complex of zirconium or hafnium tetrachloride and phosphorus oxychloride into an upper portion of a feed column containing zirconium or hafnium tetrachloride vapor and phosphorus oxychloride vapor. The liquid complex absorbing zirconium or hafnium tetrachloride vapor and producing a bottoms liquid and also producing a phosphorus oxychloride vapor stripped of zirconium or hafnium tetrachloride; introducing the bottoms liquid into a molten salt containing displacement reactor, the reactor containing molten salt comprising at least 30 mole percent lithium chloride and at least 30 mole percent of at least one other alkali metal chloride, the reactor being heated to 30-450 0 C to displace phosphorus oxychloride from the complex and product zirconium or hafnium tetrachloride vapor and phosphorus oxychloride vapor and zirconium or hafnium tetrachloride-containing molten salt; introducing the zirconium or hafnium tetrachloride vapor and the phosphorus oxychloride vapor into the feed column below the point of introduction of the liquid stream; introducing the zirconium or hafnium tetrachloride containing-molten salt into a recovery vessel where zirconium or hafnium tetrachloride is removed from the molten salt to produce zirconium or hafnium tetrachloride product and zirconium or hafnium chloride-depleted molten salt; and recycling the zirconium or hafnium tetachloride-depleted molten salt to the displacement reactor

46 CFR 173.020 - Intact stability standards: Counterballasted and non-counterballasted vessels.

Science.gov (United States)

2010-10-01

...) SUBDIVISION AND STABILITY SPECIAL RULES PERTAINING TO VESSEL USE Lifting § 173.020 Intact stability standards... vessel that is not equipped to counter-ballast while lifting must be shown by design calculations to... and crane radius. (b) Each vessel must have a righting arm curve with the following characteristics...

Three-quasiparticle isomer in 173Ta and the excitation energy dependence of K -forbidden transition rates

OpenAIRE

Wood, RT; Walker, PM; Lane, G J; Carroll, R. J.; Cullen, David; Dracoulis, G D; Hota, S. S.; Kibédi, T.; Palalani, N; Podolyak, Zs.; Reed, MW; Schiffl, K; Wright, A.M

2017-01-01

Using the 168Er(10B,5n) reaction at a beam energy of 68 MeV, new data have been obtained for the population and decay of a T1/2=148ns, Kπ=21/2− three-quasiparticle isomer at 1717 keV in 173Ta. Revised decay energies and intensities have been determined, together with newly observed members of a rotational band associated with the isomer. By comparison with other isomers in the A≈180 deformed region, the 173Ta isomer properties help to specify the key degrees of freedom that determine K-forbid...

49 CFR 173.134 - Class 6, Division 6.2-Definitions and exceptions.

Science.gov (United States)

2010-10-01

... transportation and also capable of cutting or penetrating skin or a packaging material. Sharps includes needles... § 173.199, as appropriate. (9) Dried blood spots or specimens for fecal occult blood detection placed on... cutting or penetrating skin or packaging material, the primary container must be capable of retaining the...

Growth of HfO{sub x} thin films by reactive molecular beam epitaxy

Energy Technology Data Exchange (ETDEWEB)

Hildebrandt, Erwin; Kurian, Jose; Alff, Lambert [Institut fuer Materialwissenschaft, TU Darmstadt (Germany)

2008-07-01

Thin films of hafnium oxide were grown on single crystal r-cut and c-cut sapphire by reactive molecular beam epitaxy. The conditions for the growth of single oriented hafnium oxide thin films have been established. Hafnium oxide thin films were characterized by X-ray diffraction and optical absorption measurements. It was found that hafnium oxide thin films grown on r-cut sapphire were (00l) oriented whereas, on c-cut sapphire, hafnium oxide films showed different orientations depending on the growth temperature and oxidation conditions. The hafnium oxide films grown at higher temperature and under strong oxidation conditions yielded (001) oriented films on c-cut sapphire whereas slightly weaker oxidation condition leads to (111) oriented hafnium oxide films. The bandgap deducted from optical absorption measurement carried out on hafnium oxide films grown under optimized conditions agreed well with the values reported in literature. A range of oxygen deficient thin films of hafnium oxide were also grown on single crystal sapphire substrates in order to investigate the effect of oxygen vacancies on dielectric properties of hafnium oxide. The oxygen deficient thin films of hafnium oxide show a decrease in bandgap with increase in oxygen deficiency.

Evaluation and Enhancement of the Oxygen Reduction Reaction Activity on Hafnium Oxide Nanoparticles Assisted by L(+)-lysine

International Nuclear Information System (INIS)

Chisaka, Mitsuharu; Itagaki, Noriaki

2016-01-01

Evaluation of the oxygen reduction reaction (ORR) on oxide compounds is difficult owing to the insulating nature of oxides. In this study, various amounts of L(+)-lysine were added to the precursor dispersion for the hydrothermal synthesis of hafnium oxide nanoparticles on reduced graphene oxide sheets (HfO_x–rGO) to coat the HfO_x catalysts with layers of carbon, thereby increasing the conductivity and number of active sites. When the mass ratio of L(+)-lysine to GO, R, was above 26, carbon layers were formed and the amount monotonically increased with increasing R, as noted by cyclic voltammogrametry. X-ray photoelectron spectroscopy and rotating disk electrode analyses revealed that pyrolysis produced ORR-active oxygen defects, whose formation was proposed to involve carbothermal reduction. When 53 ≤ R ≤ 210, HfO_x–rGO contained a similar amount of oxygen defects and ORR activity, as represented by an onset potential of 0.9 V versus the reversible hydrogen electrode in 0.1 mol dm"−"3 H_2SO_4. However, the number of active sites depended on R due to the amount of L(+)-lysine-derived carbon layers that increased both the number of active sites and resistivity towards oxygen diffusion.

Mechanistic Studies of Hafnium-Pyridyl Amido-Catalyzed 1-Octene Polymerization and Chain Transfer Using Quench-Labeling Methods.

Science.gov (United States)

Cueny, Eric S; Johnson, Heather C; Anding, Bernie J; Landis, Clark R

2017-08-30

Chromophore quench-labeling applied to 1-octene polymerization as catalyzed by hafnium-pyridyl amido precursors enables quantification of the amount of active catalyst and observation of the molecular weight distribution (MWD) of Hf-bound polymers via UV-GPC analysis. Comparison of the UV-detected MWD with the MWD of the "bulk" (all polymers, from RI-GPC analysis) provides important mechanistic information. The time evolution of the dual-detection GPC data, concentration of active catalyst, and monomer consumption suggests optimal activation conditions for the Hf pre-catalyst in the presence of the activator [Ph 3 C][B(C 6 F 5 ) 4 ]. The chromophore quench-labeling agents do not react with the chain-transfer agent ZnEt 2 under the reaction conditions. Thus, Hf-bound polymeryls are selectively labeled in the presence of zinc-polymeryls. Quench-labeling studies in the presence of ZnEt 2 reveal that ZnEt 2 does not influence the rate of propagation at the Hf center, and chain transfer of Hf-bound polymers to ZnEt 2 is fast and quasi-irreversible. The quench-label techniques represent a means to study commercial polymerization catalysts that operate with high efficiency at low catalyst concentrations without the need for specialized equipment.

Characteristics of laser produced plasmas of hafnium and tantalum in the 1-7 nm region

Science.gov (United States)

Li, Bowen; Otsuka, Takamitsu; Sokell, Emma; Dunne, Padraig; O'Sullivan, Gerry; Hara, Hiroyuki; Arai, Goki; Tamura, Toshiki; Ono, Yuichi; Dinh, Thanh-Hung; Higashiguchi, Takeshi

2017-11-01

Soft X-ray (SXR) spectra from hafnium and tantalum laser produced plasmas were recorded in the 1-7 nm region using two Nd:YAG lasers with pulse lengths of 170 ps and 10 ns, respectively, operating at a range of power densities. The maximum focused peak power density was 2. 3 × 1014 W cm-2 for 170 ps pulses and 1. 8 × 1012 W cm-2 for 10 ns pulses, respectively. Two intense quasicontinuous intensity bands resulting from n = 4 - n = 4 and n = 4 - n = 5 unresolved transition arrays (UTAs) dominate both sets of experimental spectra. Comparison with calculations performed with the Cowan suite of atomic structure codes as well as consideration of previous experimental and theoretical results aided identification of the most prominent features in the spectra. For the 10 ns spectrum, the highest ion stage that could be identified from the n = 4 - n = 5 arrays were lower than silver-like Hf25+ and Ta26+ (which has a 4 d 104 f ground configuration) indicating that the plasma temperature attained was too low to produce ions with an outermost 4 d subshell, while for the 170 ps plasmas the presence of significantly higher stages was deduced and lines due to 4 d-5 p transitions were clearly evident. Furthermore, we show an enhancement of emission from tantalum using dual laser irradiation, and the effect of pre-pulse durations and delay times between two pulses are demonstrated.

OBIECTUL INFRACŢIUNII PREVĂZUTE LA ART.173 CP RM

Directory of Open Access Journals (Sweden)

Mihaela BOTNARENCO

2015-11-01

Full Text Available În cadrul prezentului articol analizei este supus obiectul infracţiunii de hărţuire sexuală. Inter alia, autorul formulează definiţia conceptelor de inviolabilitate sexuală şi de libertate sexuală şi stabileşte situaţiile particulare în care aceste valori sociale şi relaţiile sociale aferente sunt proteguite prin incriminarea faptei infracţionale prevăzute la art.173 CP RM. Concomitent este studiat obiectul juridic secundar al infracţiunii de hărţuire sexuală în corelaţie cu acţiunea principală, dar şi cu acţiunea secundară din conţinutul laturii obiective a componenţei de infracţiune analizate.OBJECT OF CRIME PROVIDED BY ART.173 CRIMINAL CODE OF MOLDOVA The purpose of this article is to analyze the object of the sexual harassment. Inter alia, the author defines the notions of sexual inviolability and sexual freedom as well as identifies the specific situations when these social values and related social relationships are protected by the criminal law. Moreover, the author makes a thorough analysis of the secondary legal object of this crime in connection with main and secondary acts included in the objective side of sexual harassment.

49 CFR 173.476 - Approval of special form Class 7 (radioactive) materials.

Science.gov (United States)

2010-10-01

... (radioactive) materials must maintain on file for at least one year after the latest shipment, and provide to... evidence based on calculative methods to show that the material is able to pass the tests; or other... shipping papers as “Radioactive Material, Special Form, n.o.s.” [Amdt. 173-244, 60 FR 50307, Sept. 28, 1995...

Lithium perbromate monohydrate at 296 and 173 K

International Nuclear Information System (INIS)

Blackburn, A.C.; Gerkin, R.E.

1995-01-01

Lithium tetraoxobromate(1-) monohydrate, LiBrO 4 .H 2 O, whose perchlorate analog has not yet been described, is found to be isomorphic with NaBrO 4 .H 2 O and NaClO 4 .H 2 O. Each of the two inequivalent Li ions is coordinated by six O atoms, thus forming distorted octahedra, each of which has three inequivalent Li-O distances. At room temperature, the average Li(1)-O and Li(2)-O distances are 2.150 and 2.164 A, respectively. The perbromate ion displays very nearly regular tetrahedral geometry, although it is not subject to symmetry constraints. At 296 K the average observed Br-O distance is 1.610 (4) A and the average O-Br-O angle is 109.5 (6) , while at 173 K the corresponding values are 1.613 (4) A and 109.5 (7) . The perbromate ion shows rigid-body behavior but the lithium coordination polyhedra do not. At 296 K, the average rigid-body corrected Br-O distance in the perbromate ion is 1.624 (3) A, in excellent agreement with the corresponding value reported for NaBrO 4 .H 2 O. Refinement of the two inequivalent H atoms allowed detailed analysis of the hydrogen bonding, which is more extensive than in NaBrO 4 .H 2 O or in NaClO 4 .H 2 O. The average observed B values for the H atoms [2.9 (3) A 2 at 296 K and 2.8 (3) A 2 at 173 K] are sufficiently small to suggest that dynamic disordering of the H atoms (determined by magnetic resonance methods for NaClO 4 .H 2 O) is not significant in the title salt. (orig.)

X-ray tube target

International Nuclear Information System (INIS)

Weber, R.G.

1980-01-01

A target with an improved heat emissive surface for use in a rotating anode type x-ray tube is described. The target consists of a body having a first surface portion made of x-ray emissive material and a second surface portion made of a heat emissive material comprising at least one of hafnium boride, hafnium oxide, hafnium nitride, hafnium silicide, and hafnium aluminide. (U.K.)

Materials properties of hafnium and zirconium silicates: Metal interdiffusion and dopant penetration studies

Science.gov (United States)

Quevedo Lopez, Manuel Angel

Hafnium and Zirconium based gate dielectrics are considered potential candidates to replace SiO2 or SiON as the gate dielectric in CMOS processing. Furthermore, the addition of nitrogen into this pseudo-binary alloy has been shown to improve their thermal stability, electrical properties, and reduce dopant penetration. Because CMOS processing requires high temperature anneals (up to 1050°C), it is important to understand the diffusion properties of any metal associated with the gate dielectric in silicon at these temperatures. In addition, dopant penetration from the doped polysilicon gate into the Si channel at these temperatures must also be studied. Impurity outdiffusion (Hf, Zr) from the dielectric, or dopant (B, As, P) penetration through the dielectric into the channel region would likely result in deleterious effects upon the carrier mobility. In this dissertation extensive thermal stability studies of alternate gate dielectric candidates ZrSixOy and HfSixO y are presented. Dopant penetration studies from doped-polysilicon through HfSixOy and HfSixOyNz are also presented. Rutherford Backscattering Spectroscopy (RBS), Heavy Ion RBS (HI-RBS), X-ray Photoelectron Spectroscopy (XPS), High Resolution Transmission Electron Microscopy (HR-TEM), and Time of Flight and Dynamic Secondary Ion Mass Spectroscopy (ToF-SIMS, D-SIMS) methods were used to characterize these materials. The dopant diffusivity is calculated by modeling of the dopant profiles in the Si substrate. In this disseration is reported that Hf silicate films are more stable than Zr silicate films, from the metal interdiffusion point of view. On the other hand, dopant (B, As, and P) penetration is observed for HfSixO y films. However, the addition of nitrogen to the Hf - Si - O systems improves the dopant penetration properties of the resulting HfSi xOyNz films.

49 CFR 173.220 - Internal combustion engines, self-propelled vehicles, mechanical equipment containing internal...

Science.gov (United States)

2010-10-01

... and vehicles with certain electronic equipment when transported by aircraft or vessel. When an... vehicles, mechanical equipment containing internal combustion engines, and battery powered vehicles or... Than Class 1 and Class 7 § 173.220 Internal combustion engines, self-propelled vehicles, mechanical...

3' fragment of miR173-programmed RISC-cleaved RNA is protected from degradation in a complex with RISC and SGS3.

Science.gov (United States)

Yoshikawa, Manabu; Iki, Taichiro; Tsutsui, Yasuhiro; Miyashita, Kyoko; Poethig, R Scott; Habu, Yoshiki; Ishikawa, Masayuki

2013-03-05

trans-acting small interfering RNAs (tasiRNAs) are plant-specific endogenous siRNAs produced via a unique pathway whose first step is the microRNA (miRNA)-programmed RNA-induced silencing complex (RISC)-mediated cleavage of tasiRNA gene (TAS) transcripts. One of the products is subsequently transformed into tasiRNAs by a pathway that requires several factors including SUPPRESSOR OF GENE SILENCING3 (SGS3) and RNA-DEPENDENT RNA POLYMERASE6. Here, using in vitro assembled ARGONAUTE (AGO)1-RISCs, we show that SGS3 is recruited onto RISCs only when they bind target RNA. Following cleavage by miRNA173 (miR173)-programmed RISC, SGS3 was found in complexes containing cleaved TAS2 RNA and RISC. The 3' cleavage fragment (the source of tasiRNAs) was protected from degradation in this complex. Depletion of SGS3 did not affect TAS2 RNA cleavage by miR173-programmed RISC, but did affect the stability of the 3' cleavage fragment. When the 3' nucleotide of 22-nt miR173 was deleted or the corresponding nucleotide in TAS2 RNA was mutated, the complex was not observed and the 3' cleavage fragment was degraded. Importantly, these changes in miR173 or TAS2 RNA are known to lead to a loss of tasiRNA production in vivo. These results suggest that (i) SGS3 associates with AGO1-RISC via the double-stranded RNA formed by the 3'-terminal nucleotides of 22-nt miR173 and corresponding target RNA, which probably protrudes from the AGO1-RISC molecular surface, (ii) SGS3 protects the 3' cleavage fragment of TAS2 RNA from degradation, and (iii) the observed SGS3-dependent stabilization of the 3' fragment of TAS2 RNA is key to tasiRNA production.

Are there non-statistical effects in /sup 173/Yb(n,gamma)/sup 174/Yb?

International Nuclear Information System (INIS)

Pospisil, S.; Becvar, F.; Chrien, R.E.; Kopecky, J.

1987-01-01

The resonance-averaged capture of neutrons in 173 Yb has been studied at energy of 2 keV. With a statistical significance of 99.5% an enhancement of E1-transition to the neutron 2QP levels in 174 Yb is observed. 8 refs

Lifetime embrittlement of reactor core materials

International Nuclear Information System (INIS)

Kreyns, P.H..; Bourgeois, W.F.; Charpentier, P.L.; Kammenzind, B.F.; Franklin, D.G.; White, C.J.

1994-08-01

Over a core lifetime, the reactor materials Zircaloy-2, Zircaloy-4, and hafnium may become embrittled due to the absorption of corrosion- generated hydrogen and to neutron irradiation damage. Results are presented on the effects of fast fluence on the fracture toughness of wrought Zircaloy-2, Zircaloy-4, and hafnium; Zircaloy-4 to hafnium butt welds; and hydrogen precharged beta treated and weld metal Zircaloy-4 for fluences up to a maximum of approximately 150 x 10 24 n/M 2 (> 1 Mev). While Zircaloy-4 did not exhibit a decrement in K IC due to irradiation, hafnium and butt welds between hafnium and Zircaloy-4 are susceptible to embrittlement with irradiation. The embrittlement can be attributed to irradiation strengthening, which promotes cleavage fracture in hafnium and hafnium-Zircaloy welds, and, in part, to the lower chemical potential of hydrogen in Zircaloy-4 compared to hafnium, which causes hydrogen, over time, to drift from the hafnium end toward the Zircaloy-4 end and to precipitate at the interface between the weld and base-metal interface. Neutron radiation apparently affects the fracture toughness of Zircaloy-2, Zircaloy-4, and hafnium in different ways. Possible explanations for these differences are suggested. It was found that Zircaloy-4 is preferred over Zircaloy-2 in hafnium-to- Zircaloy butt-weld applications due to its absence of a radiation- induced reduction in K IC plus its lower hydrogen absorption characteristics compared with Zircaloy-2

A new topical hemostatic agent TT-173 reduces blood loss in a sheep model of total knee arthroplasty.

Science.gov (United States)

Centeno, Alberto; Rojas, Santiago; Arias, Belén; Miquel, Ignasi; Sánchez, Pilar; Ureta, Claudia; Rincón, Esther; López, Ramón; Murat, Jesús

2017-12-01

Total knee arthroplasty is associated with blood loss during the intervention and may require allogenic blood transfusion. Treatments such as tranexamic acid and fibrin sealants improved the bleeding control in several clinical trials, but the hemorrhage associated with the intervention is still significant. Thus far, very few studies have evaluated hemostatic treatments in animal models of total knee arthroplasty. This work describes a sheep model of bleeding associated with total knee arthroplasty and investigates a new class of hemostatic treatment based on recombinant tissue factor. Sheep were treated with the anticoagulant heparin, and the joint was accessed by a paramedial incision. Ligaments and menisci were eliminated and femoral condyles and tibia plateau were sectioned exposing the trabecular bone. An intra-articular drain was used to recover and quantify the blood loss during the 90-min period after treatment. The efficacy of one milligram and three milligrams of TT-173 was evaluated and compared with tranexamic acid. The occurrence of analytical alterations and systemic absorption was also investigated. Treatment with TT-173 reduced the blood loss in comparison with control or tranexamic acid. No significant differences were observed between the two doses evaluated. Moreover, a dose of six milligrams of TT-173 did not induce any clinical or analytical alteration, and significant systemic absorption was not observed. Data obtained strongly suggest that TT-173 could be useful in reducing the blood loss associated with total knee arthroplasty and without safety concerns derived from the systemic absorption of the product. Copyright © 2017 Elsevier B.V. All rights reserved.

The energy landscape of glassy dynamics on the amorphous hafnium diboride surface

International Nuclear Information System (INIS)

Nguyen, Duc; Girolami, Gregory S.; Mallek, Justin; Cloud, Andrew N.; Abelson, John R.; Lyding, Joseph; Gruebele, Martin

2014-01-01

Direct visualization of the dynamics of structural glasses and amorphous solids on the sub-nanometer scale provides rich information unavailable from bulk or conventional single molecule techniques. We study the surface of hafnium diboride, a conductive ultrahigh temperature ceramic material that can be grown in amorphous films. Our scanning tunneling movies have a second-to-hour dynamic range and single-point current measurements extend that to the millisecond-to-minute time scale. On the a-HfB 2 glass surface, two-state hopping of 1–2 nm diameter cooperatively rearranging regions or “clusters” occurs from sub-milliseconds to hours. We characterize individual clusters in detail through high-resolution (<0.5 nm) imaging, scanning tunneling spectroscopy and voltage modulation, ruling out individual atoms, diffusing adsorbates, or pinned charges as the origin of the observed two-state hopping. Smaller clusters are more likely to hop, larger ones are more likely to be immobile. HfB 2 has a very high bulk glass transition temperature T g , and we observe no three-state hopping or sequential two-state hopping previously seen on lower T g glass surfaces. The electronic density of states of clusters does not change when they hop up or down, allowing us to calibrate an accurate relative z-axis scale. By directly measuring and histogramming single cluster vertical displacements, we can reconstruct the local free energy landscape of individual clusters, complete with activation barrier height, a reaction coordinate in nanometers, and the shape of the free energy landscape basins between which hopping occurs. The experimental images are consistent with the compact shape of α-relaxors predicted by random first order transition theory, whereas the rapid hopping rate, even taking less confined motion at the surface into account, is consistent with β-relaxations. We make a proposal of how “mixed” features can show up in surface dynamics of glasses

Classroom Materials for Teaching "The Particle Nature of Matter." Practical Paper No. 173.

Science.gov (United States)

Pella, Milton O.; And Others

This document presents the lesson plans and tests used in the research study reported in Technical Report 173 (ED 070 658), together with descriptions of models and films developed for the teaching program. Thirty-one lessons are included, covering the topics of matter and energy; making interferences; particles; a model for matter; particles and…

Abnormal glomerular filtration rate in children, adolescents and young adults starts below 75 mL/min/1.73 m(2).

Science.gov (United States)

Pottel, Hans; Hoste, Liesbeth; Delanaye, Pierre

2015-05-01

The chronic kidney disease (CKD) classification system for children is similar to that for adults, with both mainly based on estimated glomerular filtration rate (eGFR) combined with fixed cut-off values. The main cut-off eGFR value used to define CKD is 60 mL/min/1.73 m(2), a value that is also applied for children older than 2 years of age, adolescents and young adults. Based on a literature search, we evaluated inclusion criteria for eGFR in clinical trials or research studies on CKD for children. We also collected information on direct measurements of GFR (mGFR) in children and adolescents, with the aim to estimate the normal reference range for GFR. Using serum creatinine (Scr) normal reference values and Scr-based eGFR-equations, we also evaluated the correspondence between Scr normal reference values and (e)GFR normal reference values. Based on our literature search, the inclusion of children in published CKD studies has been based on cut-off values for eGFR of >60 mL/min/1.73 m(2). The lower reference limits for mGFR far exceed this adult threshold. Using eGFR values calculated using Scr-based formulas, we found that abnormal Scr levels in children already correspond to eGFR values that are below a cut-off of 75 mL/min/1.73 m(2). Abnormal GFR in children, adolescents and young adults starts below 75 mL/min/1.73 m(2), and as abnormality is a sign of disease, we recommend referring children, adolescents and young adults with an (e)GFR of <75 mL/min/1.73 m(2) for further clinical assessment.

Development of the common law in view of Sections 39(2) and 173 ...

African Journals Online (AJOL)

The common (or non-statutory) law has also retained its position, subject however to the superior courts' inherent power, or rather their obligation in terms of section 173 of the Constitution, to develop the common law taking into account the interests of justice. The courts have for a long time had the task of developing the ...

Phase equilibria in the Zr-Si-B ternary system (Zr-Si-ZrB{sub 2} region) at 1 173 K

Energy Technology Data Exchange (ETDEWEB)

Han, Feng; Luo, Hao [Guangxi Univ., Nanning (China). College of Materials Science and Engineering; Guangxi Univ., Nanning (China). Guangxi Key Lab. of Processing for Non-ferrous Metal and Featured Materials; Zhan, Yongzhong [Guangxi Univ., Nanning (China). College of Materials Science and Engineering; Guangxi Univ., Nanning (China). Guangxi Key Lab. of Processing for Non-ferrous Metal and Featured Materials; Guangxi Univ., Nanning (China). Center of Ecological Collaborative Innovation for Aluminum Industry

2017-10-15

The isothermal section of the Zr-Si-B ternary system (Zr-Si-ZrB{sub 2} region) at 1 173 K has been experimentally determined. All equilibrated alloys were characterized via X-ray powder diffraction and scanning electron microscopy equipped with energy-dispersive X-ray analysis. A ternary phase Zr{sub 5}(Si{sub 0.86}B{sub 0.14}){sub 3} was found at 1 173 K. The experimental results show that the isothermal section consists of 11 single-phase regions, 26 two-phase regions and 13 three-phase regions. The existence of eight compounds, i.e. ZrSi{sub 2}, ZrSi, Zr{sub 5}Si{sub 4}, Zr{sub 3}Si{sub 2}, Zr{sub 2}Si, ZrB, ZrB{sub 2} and Zr{sub 5}(Si{sub 0.86}B{sub 0.14}){sub 3} in this system has been confirmed in the Zr-Si-ZrB{sub 2} region at 1 173 K.

49 CFR 173.9 - Transport vehicles or freight containers containing lading which has been fumigated.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Transport vehicles or freight containers... MATERIALS REGULATIONS SHIPPERS-GENERAL REQUIREMENTS FOR SHIPMENTS AND PACKAGINGS General § 173.9 Transport... hazardous material. (b) No person may offer for transportation or transport a rail car, freight container...

An Auger electron spectroscopy study on the anodization process of high-quality thin-film capacitors made of hafnium

International Nuclear Information System (INIS)

Noya, Atsushi; Sasaki, Katsutaka; Umezawa, Toshiji

1989-01-01

Formation process of the anodic oxide film of hafnium for use as a thin-film capacitor has been examined by the current-voltage characteristics of the anodization and the in-depth analysis of formed oxide using Auger electron spectroscopy. It is found that the oxide growth obeys three different rate laws such as the linear rate law at first and next the parabolic rate law during the constant current anodization, and then the reciprocal logarithmic rate law during the constant voltage anodization following after the constant current process. From the Auger electron spectroscopy analysis, it is found that the shape of the compositional depth profile of the grown oxide film varies associating with the rate law of oxidation obeyed. The variation of depth profile correlating with the rate law is discussed with respect to each elementary process such as the transport and/or the reaction of chemical species interpreted from the over-all behavior of anodization process. It is revealed that the stoichiometric film having an interface with sharp transition, which is favorable for obtaining excellent electrical properties of the capacitor, can be obtained under the condition that the phase-boundary reaction is the rate-determining step of the anodization. The constant voltage anodization process also satisfies such circumstances and therefore can be favorable method for preparing highquality thin-film capacitors. (author)

Contribution towards ALD and MOCVD of rare earth oxides and hafnium oxide. From precursor evaluation to process development and thin film characterization

International Nuclear Information System (INIS)

Xu, Ke

2013-01-01

elements for ALD applications. A possible synthesis route is the salt metatheses route. It could be expected that the monodentate guanidine ligand would provide increased reactivity towards water, where the bulky guanidine ligands will shield the RE center providing self-limiting growth behavior. In Chapter 4 and 7, ALD of rare earth oxides and hafnium oxide using corresponding guanidinate precursors are in detail investigated. According to the measurements, these processes are true ALD processes with broad ALD windows, high growth per cycle in the saturated area. Furthermore, the rare earth guanidinate and hafnium guanidinate precursors exhibit matching ALD window in the temperature range of 200 - 225 C. This motivated us to deposite trinary oxide thin films (HfREOx) using corresponding precursor combinations.

3′ fragment of miR173-programmed RISC-cleaved RNA is protected from degradation in a complex with RISC and SGS3

Science.gov (United States)

Yoshikawa, Manabu; Iki, Taichiro; Tsutsui, Yasuhiro; Miyashita, Kyoko; Poethig, R. Scott; Habu, Yoshiki; Ishikawa, Masayuki

2013-01-01

trans-acting small interfering RNAs (tasiRNAs) are plant-specific endogenous siRNAs produced via a unique pathway whose first step is the microRNA (miRNA)-programmed RNA-induced silencing complex (RISC)–mediated cleavage of tasiRNA gene (TAS) transcripts. One of the products is subsequently transformed into tasiRNAs by a pathway that requires several factors including SUPPRESSOR OF GENE SILENCING3 (SGS3) and RNA-DEPENDENT RNA POLYMERASE6. Here, using in vitro assembled ARGONAUTE (AGO)1–RISCs, we show that SGS3 is recruited onto RISCs only when they bind target RNA. Following cleavage by miRNA173 (miR173)-programmed RISC, SGS3 was found in complexes containing cleaved TAS2 RNA and RISC. The 3′ cleavage fragment (the source of tasiRNAs) was protected from degradation in this complex. Depletion of SGS3 did not affect TAS2 RNA cleavage by miR173-programmed RISC, but did affect the stability of the 3′ cleavage fragment. When the 3′ nucleotide of 22-nt miR173 was deleted or the corresponding nucleotide in TAS2 RNA was mutated, the complex was not observed and the 3′ cleavage fragment was degraded. Importantly, these changes in miR173 or TAS2 RNA are known to lead to a loss of tasiRNA production in vivo. These results suggest that (i) SGS3 associates with AGO1–RISC via the double-stranded RNA formed by the 3′-terminal nucleotides of 22-nt miR173 and corresponding target RNA, which probably protrudes from the AGO1–RISC molecular surface, (ii) SGS3 protects the 3′ cleavage fragment of TAS2 RNA from degradation, and (iii) the observed SGS3-dependent stabilization of the 3′ fragment of TAS2 RNA is key to tasiRNA production. PMID:23417299

Nano-crystals of cerium–hafnium binary oxide: Their size-dependent structure

Energy Technology Data Exchange (ETDEWEB)

Raitano, Joan M. [Department of Applied Physics and Applied Mathematics, Materials Science and Engineering Program, Columbia University, New York, NY 10027 (United States); Khalid, Syed [National Synchrotron Light Source, Brookhaven National Laboratory, Upton, NY 11973 (United States); Marinkovic, Nebojsa [Chemical Engineering Department, Columbia University, 500 W 120th St, Mudd 801, New York, NY 10027 (United States); Chan, Siu-Wai, E-mail: sc174@columbia.edu [Department of Applied Physics and Applied Mathematics, Materials Science and Engineering Program, Columbia University, New York, NY 10027 (United States)

2015-09-25

Highlights: • (1 − x)CeO{sub 2}–xHfO{sub 2} was precipitated (0 < x < 1) and calcined in air. • For x ⩽ 0.14, crystallites ⩽140 nm in size exhibit only the fluorite structure. • This low hafnia solubility is attributable to no auto-reduction (Ce{sup 3+} = 0). • The low solubility is also due to the high temperature required for homogenization. • Coarsening is lessened as Hf{sup 4+} ions slow cation diffusion in these crystallites. - Abstract: Cerium oxide (CeO{sub 2}, “ceria”) and hafnium oxide (HfO{sub 2}, “hafnia”) were aqueously co-precipitated and subsequently calcined to allow for homogenization. The size of the (1−x)CeO{sub 2}–xHfO{sub 2} crystallites, determined by the Scherrer equation, varied from 140 nm for x = 0 to 15 nm for x = 0.73. For x ⩽ 0.14, only cubic structures are visible in X-ray diffractograms, and the lattice parameters are consistent with the values expected for structurally cubic solid solutions of hafnia in ceria. At x = 0.26, tetragonal and monoclinic phases nucleated with the former not being observed in the bulk phase diagram for ceria–hafnia. Therefore, the solubility limit of the cubic structure is between x = 0.14 and x = 0.26 for 40–61 nm crystallites, the sizes of these respective compositions. More specifically, for the 40 nm crystallites of x = 0.26 (1 − x)CeO{sub 2}–xHfO{sub 2}, 15% of the hafnia remains in a structurally cubic solid solution with ceria based on the observed cubic lattice parameter. The compositional domain for the cubic fluorite structure in this study is narrower than other nanostructured (1 − x)CeO{sub 2}–xHfO{sub 2} studies, especially studies with crystallite sizes less than 10 nm, but wider than observed in the bulk and helps to expand the size regime over which the relationship between crystallite size and phase stability is known. The extent of this cubic-structure domain is mainly attributable to the intermediate crystallite size and the roughly zero Ce{sup 3

Comparative performance of the CKD Epidemiology Collaboration (CKD-EPI) and the Modification of Diet in Renal Disease (MDRD) Study equations for estimating GFR levels above 60 mL/min/1.73 m2.

Science.gov (United States)

Stevens, Lesley A; Schmid, Christopher H; Greene, Tom; Zhang, Yaping Lucy; Beck, Gerald J; Froissart, Marc; Hamm, Lee L; Lewis, Julia B; Mauer, Michael; Navis, Gerjan J; Steffes, Michael W; Eggers, Paul W; Coresh, Josef; Levey, Andrew S

2010-09-01

The Modification of Diet in Renal Disease (MDRD) Study equation underestimates measured glomerular filtration rate (GFR) at levels>60 mL/min/1.73 m2, with variable accuracy among subgroups; consequently, estimated GFR (eGFR)>or=60 mL/min/1.73 m2 is not reported by clinical laboratories. Here, performance of a more accurate GFR-estimating equation, the Chronic Kidney Disease Epidemiology Collaboration (CKD-EPI) equation, is reported by level of GFR and clinical characteristics. Test of diagnostic accuracy. Pooled data set of 3,896 people from 16 studies with measured GFR (not used for the development of either equation). Subgroups were defined by eGFR, age, sex, race, diabetes, prior solid-organ transplant, and body mass index. eGFR from the CKD-EPI and MDRD Study equations and standardized serum creatinine. Measured GFR using urinary or plasma clearance of exogenous filtration markers. Mean measured GFR was 68+/-36 (SD) mL/min/1.73 m2. For eGFR73 m2, both equations have similar bias (median difference compared with measured GFR). For eGFR of 30-59 mL/min/1.73 m2, bias was decreased from 4.9 to 2.1 mL/min/1.73 m2 (57% improvement). For eGFR of 60-89 mL/min/1.73 m2, bias was decreased from 11.9 to 4.2 mL/min/1.73 m2 (61% improvement). For eGFR of 90-119 mL/min/1.73 m2, bias was decreased from 10.0 to 1.9 mL/min/1.73 m2 (75% improvement). Similar or improved performance was noted for most subgroups with eGFR73 m2, other than body mass indexor=90 mL/min/1.73 m2. Limited number of elderly people and racial and ethnic minorities with measured GFR. The CKD-EPI equation is more accurate than the MDRD Study equation overall and across most subgroups. In contrast to the MDRD Study equation, eGFR>or=60 mL/min/1.73 m2 can be reported using the CKD-EPI equation. Copyright (c) 2010 National Kidney Foundation, Inc. All rights reserved.

49 CFR 173.427 - Transport requirements for low specific activity (LSA) Class 7 (radioactive) materials and...

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Transport requirements for low specific activity... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.427 Transport requirements for low specific... must be transported in accordance with the following conditions: (1) The external dose rate may not...

L2₁ and XA Ordering Competition in Hafnium-Based Full-Heusler Alloys Hf₂VZ (Z = Al, Ga, In, Tl, Si, Ge, Sn, Pb).

Science.gov (United States)

Wang, Xiaotian; Cheng, Zhenxiang; Wang, Wenhong

2017-10-20

For theoretical designing of full-Heusler based spintroinc materials, people have long believed in the so-called Site Preference Rule (SPR). Very recently, according to the SPR, there are several studies on XA-type Hafnium-based Heusler alloys X₂YZ, i.e., Hf₂VAl, Hf₂CoZ (Z = Ga, In) and Hf₂CrZ (Z = Al, Ga, In). In this work, a series of Hf₂-based Heusler alloys, Hf₂VZ (Z = Al, Ga, In, Tl, Si, Ge, Sn, Pb), were selected as targets to study the site preferences of their atoms by first-principle calculations. It has been found that all of them are likely to exhibit the L2₁-type structure instead of the XA one. Furthermore, we reveal that the high values of spin-polarization of XA-type Hf₂VZ (Z = Al, Ga, In, Tl, Si, Ge, Sn, Pb) alloys have dropped dramatically when they form the L2₁-type structure. Also, we prove that the electronic, magnetic, and physics nature of these alloys are quite different, depending on the L2₁-type or XA-type structures.

Growth of conductive HfO{sub 2-x} thin films by reactive molecular beam epitaxy

Energy Technology Data Exchange (ETDEWEB)

Hildebrandt, Erwin; Kurian, Jose; Alff, Lambert [Institut fuer Materialwissenschaft, TU Darmstadt (Germany); Kleebe, Hans-Joachim [Institut fuer Angewandte Geowissenschaften, TU Darmstadt (Germany)

2009-07-01

Thin films of oxygen deficient hafnium oxide were grown on single crystal c-cut and r-cut sapphire substrates by reactive molecular beam epitaxy. The oxidation conditions during growth were varied within a wide range using RF-activated oxygen. Hafnium oxide thin films were characterized using X-ray diffraction, resistivity measurements ({rho}-T) and transmission electron microscopy (TEM). The results show a dramatic increase in conductivity of the deposited oxygen deficient hafnium oxide thin films with decreasing oxidation conditions during growth. The electrical properties of deficient hafnium oxide thin films varied from insulating over semiconducting to conducting. X-ray diffraction data as well as TEM data rule out the possibility of conductivity due to metallic hafnium.

Fermented Milk Containing Bifidobacterium lactis DN-173 010 in Childhood Constipation: A Randomized, Double-Blind, Controlled Trial

NARCIS (Netherlands)

Tabbers, Merit M.; Chmielewska, Ania; Roseboom, Maaike G.; Crastes, Nolwenn; Perrin, Catherine; Reitsma, Johannes B.; Norbruis, Obbe; Szajewska, Hania; Benninga, Marc A.

2011-01-01

BACKGROUND: Constipation is a frustrating symptom affecting 3% of children worldwide. A fermented dairy product containing Bifidobacterium lactis strain DN-173 010 was effective in increasing stool frequency in constipated women. Our aim was to assess the effects of this product in constipated

Hafnium in peralkaline and peraluminous boro-aluminosilicate glass, and glass subcomponents: a solubility study

International Nuclear Information System (INIS)

Davis, Linda L.; Darab, John G.; Qian, Maoxu; Zhao, Donggao; Palenik, Christopher S.; Li, Hong; Strachan, Denis M.; Li, Liyu

2003-01-01

A relationship between the solubility of hafnia (HfO2) and the host glass composition was explored by determining the solubility limits of HfO2 in peralkaline and peraluminous borosilicate glasses in the system SiO2-Al2O3-B2O3-Na2O, and in glasses in the system SiO2-Na2O-Al2O3 in air at 1450 C. The only Hf-bearing phase to crystallize in the peralkaline borosilicate melts is hafnia, while in the boron-free melts sodium-hafnium silicates crystallize. All peraluminous borosilicate melts crystallize hafnia, but the slightly peraluminous glasses also have sector-zoned hafnia crystals that contain Al and Si. The more peraluminous borosilicate glasses also crystallize a B-containing mullite. The general morphology of the hafnia crystals changes as peralkalinity (Na2O/(Na2O+Al2O3)) decreases, as expected in melts with increasing viscosity. In all of the glasses with Na2O > Al2O3, the solubility of hafnia is linearly and positively correlated with Na2O/(Na2O + Al2O3) or Na2O - Al2O3 (excess sodium), despite the presence of 5 to 16 mol% B2O3. The solubility of hafnia is higher in the sodium-aluminum borosilicate glasses than in the sodium-aluminosilicate glasses, suggesting that the boron is enhancing the effect that excess sodium has on the incorporation of Hf into the glass structure. The results of this solubility study are compared to other studies of high-valence cation solubility in B-free silicate melts. From this, for peralkaline B-bearing glasses, it is shown that, although the solubility limits are higher, the solution behavior of hafnia is the same as in B-free silicate melts previously studied. By comparison, also, it is shown that in peraluminous melts, there must be a different solution mechanism for hafnia: different than for peralkaline sodium-aluminum borosilicate glasses and different than for B-free silicate melts studied by others

Multi-quasi-particle states in 173Hf

International Nuclear Information System (INIS)

Fabricius, B.; Dracoulis, G.D.; Kibedi, T.; Stuchbery, A.E.; Baxter, A.M.

1991-01-01

Rotational bands built on 1, 3 and 5 quasi-particle (qp) states in 173 Hf have been populated to medium and high spins through the 160 Gd( 18 O, 5n) reaction. The 1qp bands, previously identified as the 1/2 - [521], 5/2 - [512] and 7/2 + [633] (mixed i 13/2 ) Nilsson configurations, have been extended past the first back-bend and show different alignment properties, possibly originating from deformation differences. The multi-particle states were identified from excitation energies, the properties of their associated band structures and decay patterns. The 3qp states are the previously known K π =19/2 + and 23/2 - isomeric states originating from the 7/2 + [633] quasi-neutron coupled to the 6 + and 8 - , 2-quasi-proton excitations and a K π =(13/2 + ) state possibly containing the three lowest quasi-neutrons. A 5qp state with K π =(29/2 - ) was identified as the same three lowest lying quasi-neutrons coupled to the 8 - , 2-quasi-proton excitation. The low excitation energies of these two related 3- and 5-quasi-particle states implies a reduced neutron pairing gap, which can be attributed to the effect of blocking. (orig.)

Investigation of a miRNA-Induced Gene Silencing Technique in Petunia Reveals Alterations in miR173 Precursor Processing and the Accumulation of Secondary siRNAs from Endogenous Genes.

Directory of Open Access Journals (Sweden)

Yao Han

Full Text Available MIGS (miRNA-induced gene silencing is a straightforward and efficient gene silencing technique in Arabidopsis. It works by exploiting miR173 to trigger the production of phasiRNAs (phased small interfering RNAs. MIGS can be used in plant species other than Arabidopsis by co-expression of miR173 and target gene fragments fused to an upstream miR173 target site. However, the efficiency and technical mechanisms have not been thoroughly investigated in other plants. In this work, two vectors, pMIGS-chs and pMIGS-pds, were constructed and transformed into petunia plants. The transgenic plants showed CHS (chalcone synthase and PDS (phytoene desaturase gene-silencing phenotypes respectively, indicating that MIGS functions in petunia. MIGS-chs plants were used to investigate the mechanisms of this technique in petunia. Results of 5'- RACE showed that the miR173 target site was cleaved at the expected position and that endogenous CHS genes were cut at multiple positions. Small RNA deep sequencing analysis showed that the processing of Arabidopsis miR173 precursors in MIGS-chs transgenic petunia plants did not occur in exactly the same way as in Arabidopsis, suggesting differences in the machinery of miRNA processing between plant species. Small RNAs in-phase with the miR173 cleavage register were produced immediately downstream from the cleavage site and out-of-phase small RNAs were accumulated at relatively high levels from processing cycle 5 onwards. Secondary siRNAs were generated from multiple sites of endogenous CHS-A and CHS-J genes, indicating that miR173 cleavage induced siRNAs have the same ability to initiate siRNA transitivity as the siRNAs functioning in co-suppression and hpRNA silencing. On account of the simplicity of vector construction and the transitive amplification of signals from endogenous transcripts, MIGS is a good alternative gene silencing method for plants, especially for silencing a cluster of homologous genes with redundant

Investigation of a miRNA-Induced Gene Silencing Technique in Petunia Reveals Alterations in miR173 Precursor Processing and the Accumulation of Secondary siRNAs from Endogenous Genes.

Science.gov (United States)

Han, Yao; Zhang, Bin; Qin, Xiaoting; Li, Mingyang; Guo, Yulong

2015-01-01

MIGS (miRNA-induced gene silencing) is a straightforward and efficient gene silencing technique in Arabidopsis. It works by exploiting miR173 to trigger the production of phasiRNAs (phased small interfering RNAs). MIGS can be used in plant species other than Arabidopsis by co-expression of miR173 and target gene fragments fused to an upstream miR173 target site. However, the efficiency and technical mechanisms have not been thoroughly investigated in other plants. In this work, two vectors, pMIGS-chs and pMIGS-pds, were constructed and transformed into petunia plants. The transgenic plants showed CHS (chalcone synthase) and PDS (phytoene desaturase) gene-silencing phenotypes respectively, indicating that MIGS functions in petunia. MIGS-chs plants were used to investigate the mechanisms of this technique in petunia. Results of 5'- RACE showed that the miR173 target site was cleaved at the expected position and that endogenous CHS genes were cut at multiple positions. Small RNA deep sequencing analysis showed that the processing of Arabidopsis miR173 precursors in MIGS-chs transgenic petunia plants did not occur in exactly the same way as in Arabidopsis, suggesting differences in the machinery of miRNA processing between plant species. Small RNAs in-phase with the miR173 cleavage register were produced immediately downstream from the cleavage site and out-of-phase small RNAs were accumulated at relatively high levels from processing cycle 5 onwards. Secondary siRNAs were generated from multiple sites of endogenous CHS-A and CHS-J genes, indicating that miR173 cleavage induced siRNAs have the same ability to initiate siRNA transitivity as the siRNAs functioning in co-suppression and hpRNA silencing. On account of the simplicity of vector construction and the transitive amplification of signals from endogenous transcripts, MIGS is a good alternative gene silencing method for plants, especially for silencing a cluster of homologous genes with redundant functions.

Study on gamma rays from the 173Ybsub (n,γ) 174Yb reaction with resonance neutrons

International Nuclear Information System (INIS)

Aldea, L.; Bechvarzh, F.; Gonzatko, Ya.; Pospishil, S; Telezhnikov, S.A.

1976-01-01

Relative intensities of primary transitions from individual 173 Yb + n resonances were measured. For 9 resonances with Jsub (π) = 2 - and for 8 transitions an experimental correlation coefficient Rsub(exp) = 0.40 between GITAsub(n lambda) 0 deg and Isub(*g lambda f) / Esub(*g) 5 deg was found to have a significance level 99.8 %

Comparison of HfCl4, HfI4, TEMA-Hf, and TDMA-Hf as precursors in early growing stages of HfO2 films deposited by ALD: A DFT study

International Nuclear Information System (INIS)

Cortez-Valadez, M.; Fierro, C.; Farias-Mancilla, J.R.; Vargas-Ortiz, A.; Flores-Acosta, M.; Ramírez-Bon, R.; Enriquez-Carrejo, J.L.

2016-01-01

Highlights: • Hafnium oxide growth on Si(100) by atomic layer deposition was simulated. • The interface structure was considered as silicate and silicide. • The interface was studied employing DFT. • TDMA-Hf precursor show better interface stability. - Abstract: The final structure of HfO 2 films grown by atomic layer deposition (ALD) after reaction with OH − ions has been analyzed by DFT (density functional theory). The interaction of the precursors: HfCl 4 (hafnium tetrachloride), HfI 4 (hafnium tetraiodide), TEMA-Hf (tetrakis-ethylmethylamino hafnium), and TDMA-Hf (tetrakis-dimethylamino hafnium) with HO–H was studied employing the B3LYP (Becke 3-parameter, Lee–Yang–Parr) hybrid functional and the PBE (Perdew–Burke–Ernzerhof) generalized gradient functional. The structural evolution at the Si(100) surface has been analyzed by LDA (local density approximation). The structural parameters: bond length and bond angle, and the vibrational parameters for the optimized structures are also reported. The presence of hafnium silicate at the interface was detected. The infrared spectra and structural parameters obtained in this work agree with previously reported experimental results.

Multi-quasi-particles states in 173Hf

International Nuclear Information System (INIS)

Fabricius, B.; Dracoulis, G.D.; Kibedi, T.; Stuchbery, A.E.; Baxter, A.M.

1990-10-01

Rotational bands built on 1, 3 and 5 quasi-particle (qp) states in 173 Hf have been populated to medium and high spins through the 160 Gd ( 18 O,5n) reaction. The 1qp bands, previously identified as the 1/2 - [521], 5/2 - [512] and 7/2 + [633] (mixed i 1 3 /2 ) Nilsson configurations, have been extended past the first back-bend and show different alignment properties, possibly originating from deformation differences. The multi-particle states were identified from excitation energies, the properties of their associated band structures and decay patterns. The 3 qp states are the previously known K π 19/2 + and 23/2 - isomeric states originating from the 7/2 + [633] quasi-neutron coupled to the 6 + and 8 - , 2-quasi-proton excitations and a K π = (13/2 + ) state possibly containing the three lowest quasi-neutrons. A 5 qp state with K π = (29/2 - ) was identified as the same three lowest lying quasi-neutrons coupled to the 8 - , 2-quasi-proton excitation. The low excitation energies of these two related 3- and 5-quasi-particle states implies a reduced neutron pairing gap, which can be attributed to the effect of blocking. 28 refs., 2 tabs., 9 figs

Synthesis and characterization of hafnium carbide microcrystal chains with a carbon-rich shell via CVD

International Nuclear Information System (INIS)

Tian, Song; Li, Hejun; Zhang, Yulei; Liu, Sen; Fu, Yangxi; Li, Yixian; Qiang, Xinfa

2013-01-01

Graphical abstract: Novel HfC microcrystal chains have been synthesized via a catalyst-assisted chemical vapor deposition process. SEM results show the chains have a periodically changing diameter and a nanoscale sharpening tip. Analysis of TEM/SAED/EELS/EDX data shows the single-crystal chains grow along a [0 0 1] direction and consist of a HfC core and a thin carbon-rich shell with embedded HfC nanocrystallites surrounding the core. This work achieves the controllable preparation of nanoscale HfC sharpening tips for application as a point electron emission source and facilitates the application of HfC ultrafast laser-triggered tips in attosecond science. Highlights: •HfC microcrystal chains were synthesized by a catalyst-assisted CVD. •The chains grow along a [0 0 1] direction and have a periodically changing diameter. •Single-crystal HfC core is sheathed by a thin carbon-rich shell. •A growth mechanism model is proposed to explain the growth of microcrystal chians. •This work achieves the controllable preparation of nanoscale HfC sharpening tips. -- Abstract: Novel hafnium carbide (HfC) microcrystal chains, with a periodically changing diameter and a nanoscale sharpening tip at the chain end, have been synthesized via a catalyst-assisted chemical vapor deposition (CVD) process. The as-synthesized chains with many octahedral microcrystals have diameters of between several hundreds of nm and 6 μm and lengths of ∼500 μm. TEM diffraction studies show that the chains are single-crystalline HfC and preferentially grow along a [0 0 1] crystal orientation. TEM/EELS/EDX analysis proves the chains are composed of a HfC core and a thin (several tens of nm to 100 nm) carbon-rich shell with the embedded HfC nanocrystallites (typically below 10 nm) surrounding the core. The growth mechanism model for the chains based on the vapor–liquid–solid process, the vapor–solid process, and the HfC crystal growth characteristics is discussed

Design of an Extractive Distillation Column for the Environmentally Benign Separation of Zirconium and Hafnium Tetrachloride for Nuclear Power Reactor Applications

Directory of Open Access Journals (Sweden)

Le Quang Minh

2015-09-01

Full Text Available Nuclear power with strengthened safety regulations continues to be used as an important resource in the world for managing atmospheric greenhouse gases and associated climate change. This study examined the environmentally benign separation of zirconium tetrachloride (ZrCl4 and hafnium tetrachloride (HfCl4 for nuclear power reactor applications through extractive distillation using a NaCl-KCl molten salt mixture. The vapor–liquid equilibrium behavior of ZrCl4 and HfCl4 over the molten salt system was correlated with Raoult’s law. The molten salt-based extractive distillation column was designed optimally using a rigorous commercial simulator for the feasible separation of ZrCl4 and HfCl4. The molten salt-based extractive distillation approach has many potential advantages for the commercial separation of ZrCl4 and HfCl4 compared to the conventional distillation because of its milder temperatures and pressure conditions, smaller number of required separation trays in the column, and lower energy requirement for separation, while still taking the advantage of environmentally benign feature by distillation. A heat-pump-assisted configuration was also explored to improve the energy efficiency of the extractive distillation process. The proposed enhanced configuration reduced the energy requirement drastically. Extractive distillation can be a promising option competing with the existing extraction-based separation process for zirconium purification for nuclear power reactor applications.

Cobalt(II), nickel(II), copper(II), zinc(II) and hafnium(IV) complexes of N'-(furan-3-ylmethylene)-2-(4-methoxyphenylamino)acetohydrazide.

Science.gov (United States)

Emam, Sanaa M; El-Saied, Fathy A; Abou El-Enein, Saeyda A; El-Shater, Heba A

2009-03-01

Cobalt(II), nickel(II), copper(II), zinc(II) and hafnium(IV) complexes of furan-2-carbaldehyde 4-methoxy-N-anilinoacetohydrazone were synthesized and characterized by elemental and thermal (TG and DTA) analyses, IR, UV-vis and (1)H NMR spectra as well as magnetic moment and molar conductivity. Mononuclear complexes are obtained with 1:1 molar ratio except complexes 3 and 9 which are obtained with 1:2 molar ratios. The IR spectra of ligand and metal complexes reveal various modes of chelation. The ligand behaves as a neutral bidentate one and coordination occurs via the carbonyl oxygen atom and azomethine nitrogen atom. The ligand behaves also as a monobasic tridentate one and coordination occurs through the enolic oxygen atom, azomethine nitrogen atom and the oxygen atom of furan ring. Moreover, the ligand behaves as a neutral tridentate and coordination occurs via the carbonyl oxygen, azomethine nitrogen and furan oxygen atoms as well as a monobasic bidentate and coordination occurs via the enolic oxygen atom and azomethine nitrogen atom. The electronic spectra and magnetic moment measurements reveal that all complexes possess octahedral geometry except the copper complex 10 possesses a square planar geometry. The thermal studies showed the type of water molecules involved in metal complexes as well as the thermal decomposition of some metal complexes.

Comparison of HfCl4, HfI4, TEMA-Hf, and TDMA-Hf as precursors in early growing stages of HfO2 films deposited by ALD: A DFT study

Science.gov (United States)

Cortez-Valadez, M.; Fierro, C.; Farias-Mancilla, J. R.; Vargas-Ortiz, A.; Flores-Acosta, M.; Ramírez-Bon, R.; Enriquez-Carrejo, J. L.; Soubervielle-Montalvo, C.; Mani-Gonzalez, P. G.

2016-06-01

The final structure of HfO2 films grown by atomic layer deposition (ALD) after reaction with OH- ions has been analyzed by DFT (density functional theory). The interaction of the precursors: HfCl4 (hafnium tetrachloride), HfI4 (hafnium tetraiodide), TEMA-Hf (tetrakis-ethylmethylamino hafnium), and TDMA-Hf (tetrakis-dimethylamino hafnium) with HO-H was studied employing the B3LYP (Becke 3-parameter, Lee-Yang-Parr) hybrid functional and the PBE (Perdew-Burke-Ernzerhof) generalized gradient functional. The structural evolution at the Si(100) surface has been analyzed by LDA (local density approximation). The structural parameters: bond length and bond angle, and the vibrational parameters for the optimized structures are also reported. The presence of hafnium silicate at the interface was detected. The infrared spectra and structural parameters obtained in this work agree with previously reported experimental results.

A spanish mineral of zirconium and hafnium. Separation of the two elements by liquid-liquid extraction, using tributyl phosphate as chelating agent; Beneficio de un mineral espanol de circonio-hafnio. Separacion de ambos elementos por extraccion liquido-liquido, empleando fosfato de tributilo como agente de quelacion

Energy Technology Data Exchange (ETDEWEB)

Ruiz Sanchez, F; Cruz Castillo, F. de la; Fernandez Cellini, R

1962-07-01

The zirconium and Hafnium oxides are obtained from a Spanish mineral of zircon with an average contest of 55% in ZrO{sub 2}-HfO{sub 2}. An alkaline fusion to open the mineral, followed by a purification by crystallization as (Zr O-Hf O)Cl{sub 2} H{sub 2}O or as (Zr-Hf) (SO{sub 4}){sub 2}. 4H{sub 2}O, is used. A discussion of the best experimental conditions for opening the mineral and of the purification method is made. (Author) 45 refs.

6-Peroxo-6-zirconium crown and its hafnium analogue embedded in a triangular polyanion: [M6(O2)6(OH)6(gamma-SiW10O36)3]18- (M = Zr, Hf).

Science.gov (United States)

Bassil, Bassem S; Mal, Sib Sankar; Dickman, Michael H; Kortz, Ulrich; Oelrich, Holger; Walder, Lorenz

2008-05-28

We have synthesized and structurally characterized the unprecedented peroxo-zirconium(IV) containing [Zr6(O2)6(OH)6(gamma-SiW10O36)3]18- (1). Polyanion 1 comprises a cyclic 6-peroxo-6-zirconium core stabilized by three decatungstosilicate units. We have also prepared the isostructural hafnium(IV) analogue [Hf6(O2)6(OH)6(gamma-SiW10O36)3]18- (2). We investigated the acid/base and redox properties of 1 by UV-vis spectroscopy and electrochemistry studies. Polyanion 1 represents the first structurally characterized Zr-peroxo POM with side-on, bridging peroxo units. The simple, one-pot synthesis of 1 and 2 involving dropwise addition of aqueous hydrogen peroxide could represent a general procedure for incorporating peroxo groups into a large variety of transition metal and lanthanide containing POMs.

Comparison of HfCl{sub 4}, HfI{sub 4}, TEMA-Hf, and TDMA-Hf as precursors in early growing stages of HfO{sub 2} films deposited by ALD: A DFT study

Energy Technology Data Exchange (ETDEWEB)

Cortez-Valadez, M. [Departamento de Investigación en Física, Universidad de Sonora, Apdo. Postal 5-88, 83190 Hermosillo, Son. (Mexico); Fierro, C.; Farias-Mancilla, J.R. [Instituto de Ingeniería y Tecnología, Departamento de Física y Matemáticas, Universidad Autónoma de Ciudad Juárez, Av. del Charro 450, Cd. Juárez C.P. 32310, Chihuahua (Mexico); Vargas-Ortiz, A. [Universidad Autónoma de Sinaloa, Facultad de Ingeniería Mochis, Ciudad Universitaria, C.P. 81223 Los Mochis, Sinaloa (Mexico); Flores-Acosta, M. [Departamento de Investigación en Física, Universidad de Sonora, Apdo. Postal 5-88, 83190 Hermosillo, Son. (Mexico); Ramírez-Bon, R. [Centro de Investigación y Estudios Avanzados del IPN, Unidad Querétaro, Apdo. Postal 1-798, 76001 Querétaro, Qro. (Mexico); Enriquez-Carrejo, J.L. [Instituto de Ingeniería y Tecnología, Departamento de Física y Matemáticas, Universidad Autónoma de Ciudad Juárez, Av. del Charro 450, Cd. Juárez C.P. 32310, Chihuahua (Mexico); and others

2016-06-15

Highlights: • Hafnium oxide growth on Si(100) by atomic layer deposition was simulated. • The interface structure was considered as silicate and silicide. • The interface was studied employing DFT. • TDMA-Hf precursor show better interface stability. - Abstract: The final structure of HfO{sub 2} films grown by atomic layer deposition (ALD) after reaction with OH{sup −} ions has been analyzed by DFT (density functional theory). The interaction of the precursors: HfCl{sub 4} (hafnium tetrachloride), HfI{sub 4} (hafnium tetraiodide), TEMA-Hf (tetrakis-ethylmethylamino hafnium), and TDMA-Hf (tetrakis-dimethylamino hafnium) with HO–H was studied employing the B3LYP (Becke 3-parameter, Lee–Yang–Parr) hybrid functional and the PBE (Perdew–Burke–Ernzerhof) generalized gradient functional. The structural evolution at the Si(100) surface has been analyzed by LDA (local density approximation). The structural parameters: bond length and bond angle, and the vibrational parameters for the optimized structures are also reported. The presence of hafnium silicate at the interface was detected. The infrared spectra and structural parameters obtained in this work agree with previously reported experimental results.

49 CFR 173.301 - General requirements for shipment of compressed gases and other hazardous materials in cylinders...

Science.gov (United States)

2010-10-01

... less; (vi) A fire extinguisher; or (vii) A “B” style cylinder with a capacity of 40 ft 3 (1.13 m3) or an “MC” style cylinder with a capacity of 10 ft 3 (0.28m3) containing acetylene. (2) For cylinders... citations affecting § 173.301, see the List of CFR Sections Affected, which appears in the Finding Aids...

49 CFR Appendix B to Part 173 - Procedure for Testing Chemical Compatibility and Rate of Permeation in Plastic Packaging and...

Science.gov (United States)

2010-10-01

... Rate of Permeation in Plastic Packaging and Receptacles B Appendix B to Part 173 Transportation Other... Plastic Packaging and Receptacles 1. The purpose of this procedure is to determine the chemical compatibility and permeability of liquid hazardous materials packaged in plastic packaging and receptacles...

Corrosion resistant surface for vanadium nitride and hafnium nitride layers as function of grain size

Science.gov (United States)

Escobar, C. A.; Caicedo, J. C.; Aperador, W.

2014-01-01

In this research it was studied vanadium nitride (VN) and hafnium nitride (HfN) film, which were deposited onto silicon (Si (100)) and AISI 4140 steel substrates via r.f. magnetron sputtering technique in Ar/N2 atmosphere with purity at 99.99% for both V and Hf metallic targets. Both films were approximately 1.2±0.1 μm thick. The crystallography structures that were evaluated via X-ray diffraction analysis (XRD) showed preferential orientations in the Bragg planes VN (200) and HfN (111). The chemical compositions for both films were characterized by EDX. Atomic Force Microscopy (AFM) was used to study the morphology; the results reveal grain sizes of 78±2 nm for VN and 58±2 nm for HfN and roughness values of 4.2±0.1 nm for VN and 1.5±0.1 nm for HfN films. The electrochemical performance in VN and HfN films deposited onto steel 4140 were studied by Tafel polarization curves and impedance spectroscopy methods (EIS) under contact with sodium chloride at 3.5 wt% solution, therefore, it was found that the corrosion rate decreased about 95% in VN and 99% for HfN films in relation to uncoated 4140 steel, thus demonstrating, the protecting effect of VN and HfN films under a corrosive environment as function of morphological characteristics (grain size). VN(grain size)=78±2.0 nm, VN(roughness)=4.2±0.1 nm, VN(corrosion rate)=40.87 μmy. HfN(grain size)=58±2.0 nm, HfN(roughness)=1.5±0.1 nm, HfN(corrosion rate)=0.205 μmy. It was possible to analyze that films with larger grain size, can be observed smaller grain boundary thus generating a higher corrosion rate, therefore, in this work it was found that the HfN layer has better corrosion resistance (low corrosion rate) in relation to VN film which presents a larger grain size, indicating that the low grain boundary in (VN films) does not restrict movement of the Cl- ion and in this way the corrosion rate increases dramatically.

Technical Note: A simulation study on the feasibility of radiotherapy dose enhancement with calcium tungstate and hafnium oxide nano- and microparticles.

Science.gov (United States)

Sherck, Nicholas J; Won, You-Yeon

2017-12-01

To assess the radiotherapy dose enhancement (RDE) potential of calcium tungstate (CaWO 4 ) and hafnium oxide (HfO 2 ) nano- and microparticles (NPs). A Monte Carlo simulation study was conducted to gauge their respective RDE potentials relative to that of the broadly studied gold (Au) NP. The study was warranted due to the promising clinical and preclinical studies involving both CaWO 4 and HfO 2 NPs as RDE agents in the treatment of various types of cancers. The study provides a baseline RDE to which future experimental RDE trends can be compared to. All three materials were investigated in silico with the software Penetration and Energy Loss of Positrons and Electrons (PENELOPE 2014) developed by Francesc Salvat and distributed in the United States by the Radiation Safety Information Computational Center (RSICC) at Oak Ridge National Laboratory. The work utilizes the extensively studied Au NP as the "gold standard" for a baseline. The key metric used in the evaluation of the materials was the local dose enhancement factor (DEF loc ). An additional metric used, termed the relative enhancement ratio (RER), evaluates material performance at the same mass concentrations. The results of the study indicate that Au has the strongest RDE potential using the DEF loc metric. HfO 2 and CaWO 4 both underperformed relative to Au with lower DEF loc of 2-3 × and 4-100 ×, respectively. The computational investigation predicts the RDE performance ranking to be: Au > HfO 2 > CaWO 4 . © 2017 American Association of Physicists in Medicine.

Study of heat conductivity, electric conductivity and thermo-emf of BiSrCaCu2Ox and Bi1.82Sr1.73Ca1.73Ca1.25Cu2.2Ox systems

International Nuclear Information System (INIS)

Zhukova, T.B.; Parfen'eva, L.S.; Popov, V.V.; Melekh, B.T.; Smirnov, I.A.; Khalmedov, Kh.M.

1991-01-01

Phase compositions are determined and temperature dependences are measured of x-heat conductivity, ρ-electric resistance and α-thermo-emf of polycrystal, monophase, highly textured HTSC samples of BiSrCaCu 2 O x and Bi 1.82 Sr 1.73 Ca 1.25 Cu 2.2 O x produced through method of direct induction melting in the air in a cold container. Sample 'aging' after storage in the air and vacuum, leading to decrease in the number of foring phases and increase in the basic phase content as well as to change of x, ρ and α coefficients is identified

Effect of Advanced Plasma Source bias voltage on properties of HfO2 films prepared by plasma ion assisted electron evaporation from metal hafnium

International Nuclear Information System (INIS)

Zhu, Meiping; Yi, Kui; Arhilger, Detlef; Qi, Hongji; Shao, Jianda

2013-01-01

HfO 2 films, using metal hafnium as starting material, are deposited by plasma-ion assisted electron evaporation with different Advanced Plasma Source (APS) bias voltages. The refractive index and extinction coefficient are calculated, the chemical state and composition, as well as the stress and aging behavior is investigated. Laser induced damage threshold (LIDT) and damage mechanism are also evaluated and discussed. Optical, structural, mechanical and laser induced damage properties of HfO 2 films are found to be sensitive to APS bias voltage. The film stress can be tuned by varying the APS bias voltage. Damage morphologies indicate the LIDT of the HfO 2 films at 1064 nm and 532 nm are dominated by the nodular-defect density in coatings, while the 355 nm LIDT is dominated by the film absorption. HfO 2 films with higher 1064 nm LIDT than samples evaporated from hafnia are achieved with bias voltage of 100 V. - Highlights: • HfO 2 films are evaporated with different Advanced Plasma Source (APS) bias voltages. • Properties of HfO 2 films are sensitive to APS bias voltage. • With a bias voltage of 100 V, HfO 2 coatings without any stress can be achieved. • Higher 1064 nm laser induced damage threshold is achieved at a bias voltage of 100 V

The human story of Crew 173- capturing a Mars analog mission

Science.gov (United States)

Shaw, Niamh; Musilova, Michaela; Pons Lorente, Arnau; Sisaid, Idriss; Naor, Roy; Blake, Richard

2017-04-01

An international crew of six scientists, engineers, artists and entrepreneurs with different space specialisations were selected by the Mars Society to take part in a Martian simulation in January 2017. An ambitious outreach and media strategy was developed, aimed at communicating the benefits of missions to Mars to the public and to capture the public's interest by telling the human story of the crew's mission. Entitled Crew 173 Team PRIMA, they entered the Mars Desert Research Station in the Utah Desert and conducted research in 3D printing, hydroponics, geology and astronomy. Both the scientific and community experience of this mission was documented through still image, video, audio, diary and daily journalling by the resident artist of the mission, Niamh Shaw. The full experience of the crew was documented (before, during and after the expedition), to capture each individual experience of the crew and the human experience of isolation of future human space missions.

Impedance Characterization of the Capacitive field-Effect pH-Sensor Based on a thin-Layer Hafnium Oxide Formed by Atomic Layer Deposition

Directory of Open Access Journals (Sweden)

Michael LEE

2014-05-01

Full Text Available As a sensing element, silicon dioxide (SiO2 has been applied within ion-sensitive field effect transistors (ISFET. However, a requirement of increasing pH-sensitivity and stability has observed an increased number of insulating materials that obtain high-k gate being applied as FETs. The increased high-k gate reduces the required metal oxide layer and, thus, the fabrication of thin hafnium oxide (HfO2 layers by atomic layer deposition (ALD has grown with interest in recent years. This metal oxide presents advantageous characteristics that can be beneficial for the advancements within miniaturization of complementary metal oxide semiconductor (CMOS technology. In this article, we describe a process for fabrication of HfO2 based on ALD by applying water (H2O as the oxygen precursor. As a first, electrochemical impedance spectroscopy (EIS measurements were performed with varying pH (2-10 to demonstrate the sensitivity of HfO2 as a potential pH sensing material. The Nyquist plot demonstrates a high clear shift of the polarization resistance (Rp between pH 6-10 (R2 = 0.9986, Y = 3,054X + 12,100. At acidic conditions (between pH 2-10, the Rp change was small due to the unmodified oxide gate (R2 = 0.9655, Y = 2,104X + 4,250. These preliminary results demonstrate the HfO2 substrate functioned within basic to neutral conditions and establishes a great potential for applying HfO2 as a dielectric material for future pH measuring FET sensors.

A silicon doped hafnium oxide ferroelectric p–n–p–n SOI tunneling field–effect transistor with steep subthreshold slope and high switching state current ratio

Directory of Open Access Journals (Sweden)

Saeid Marjani

2016-09-01

Full Text Available In this paper, a silicon–on–insulator (SOI p–n–p–n tunneling field–effect transistor (TFET with a silicon doped hafnium oxide (Si:HfO2 ferroelectric gate stack is proposed and investigated via 2D device simulation with a calibrated nonlocal band–to–band tunneling model. Utilization of Si:HfO2 instead of conventional perovskite ferroelectrics such as lead zirconium titanate (PbZrTiO3 and strontium bismuth tantalate (SrBi2Ta2O9 provides compatibility to the CMOS process as well as improved device scalability. By using Si:HfO2 ferroelectric gate stack, the applied gate voltage is effectively amplified that causes increased electric field at the tunneling junction and reduced tunneling barrier width. Compared with the conventional p–n–p–n SOI TFET, the on–state current and switching state current ratio are appreciably increased; and the average subthreshold slope (SS is effectively reduced. The simulation results of Si:HfO2 ferroelectric p–n–p–n SOI TFET show significant improvement in transconductance (∼9.8X enhancement at high overdrive voltage and average subthreshold slope (∼35% enhancement over nine decades of drain current at room temperature, indicating that this device is a promising candidate to strengthen the performance of p–n–p–n and conventional TFET for a switching performance.

Synergistic effect of carbon nanotube as sintering aid and toughening agent in spark plasma sintered molybdenum disilicide-hafnium carbide composite

Energy Technology Data Exchange (ETDEWEB)

Mukherjee, Biswajyoti; Asiq Rahman, O.S.; Sribalaji, M [Materials Science and Engineering, Indian Institute of Technology Patna, Bihta Kanpa Road, Bihta, Patna, Bihar 801103 (India); Bakshi, Srinivasa Rao [Department of Metallurgical and Materials Engineering, Indian Institute of Technology Madras, Chennai 600036 (India); Keshri, Anup Kumar, E-mail: anup@iitp.ac.in [Materials Science and Engineering, Indian Institute of Technology Patna, Bihta Kanpa Road, Bihta, Patna, Bihar 801103 (India)

2016-12-15

Hafnium carbide (HfC) along with sintering aids was consolidated at a relatively lower temperature i.e. 1600 °C (i.e. T=~0.41 T{sub m}) under a uniaxial load of 50 MPa by spark plasma sintering. Two different sintering aids such as molybdenum disilicide (MoSi{sub 2}) and carbon nanotube (CNT) were added to enhance the densification and lower the extent of grain growth in the sintered pellets. Density of the sintered pellet increased from 96.0±0.8% in HfC +5 wt% MoSi{sub 2} (HM) to 99.0±0.5% with the addition of 2 wt% CNT in HfC+5 wt% MoSi{sub 2} (HMC) at sintering temperature of 1600 °C. Further, the extent of grain growth drastically reduced from 204% in HM to 50% in HMC. Analysis of linear shrinkage during densification revealed that CNT addition increased densification rate and decreased the time required to reach the density of 99.0±0.5% at 1600 °C. Increased densification and lower degree of grain growth could be due to the synergistic effect offered by the CNT, which are as follows: (i) Lubrication effect of CNT, (ii) Lower activation energy for grain boundary diffusion (iii) Reduction in liquid phase sintering temperature and (iv) Grain boundary pinning. Fracture toughness of the sintered HM and HMC composite was obtained using indentation technique. By the addition of 2 wt% CNT in HM, drastic increase of 91% in fracture toughness was seen. This significant improvement in fracture toughness was due to the enhanced densification and relatively lower grain size of HMC. Also crack bridging, crack deflection, crack arrest, CNT and graphene sheet pull-out and swording played major role in toughening of HMC pellet.

X-ray tube targets

International Nuclear Information System (INIS)

Hirsch, H.H.

1980-01-01

In rotary targets for X-ray tubes warping is a problem which causes X-ray deficiency. A rotary target is described in which warping is reduced by using alloys of molybdenum with 0.05 to 10% iron, silicon, cobalt, tantalum, niobium, hafnium, stable metal oxide or mixture thereof. Suitable mixtures are 0.5 to 10% of tantalum, niobium or hafnium with from 0.5 to 5% yttrium oxide, or 0.05 to 0.3% of cobalt or silicon. Optionally 0.1 to 5% by weight of additional material may be alloyed with the molybdenum, such as tantalum or hafnium carbides. (author)

Ontwikkeling van die gemenereg in die lig van artikel 39(2 en 173 van die Grondwet

Directory of Open Access Journals (Sweden)

LTC Harms

2004-10-01

Full Text Available DEVELOPMENT OF THE COMMON LAW IN VIEW OF SECTIONS 39(2 AND 173 OF THE CONSTITUTIONThe point of departure in the Constitution is that the existing legal order should largely be kept intact, despite the fact that this is disliked by some. The common (or non-statutory law has also retained its position, subject however to the superior courts' inherent power, or rather their obligation in terms of section 173 of the Constitution, to develop the common law taking into account the interests of justice. The courts have for a long time had the task of developing the common law with reference to especially the boni mores, moral standards and the common notion of what is right and fair. The Bill of Rights now is a source and summation of such notion.At times there had been an exaggerated call for petere fontes. The Courts however still have the competence to adapt the law to serve commercial and other needs, even without reference to the Bill of Rights. The underlying principles of the common law are largely, though not in all respects, consistent with the Bill of Rights. There is an essential distinction between the development of a rule of the common law in accordance with constitutional norms, and the invalidation of a rule which is inconsistent with the Constitution. Courts tend not to make this distinction and this leads to inconsistencies. Some believe that the common law is perfect and unaffected by the Bill of Rights. Others consider the Bill of Rights to have granted the judiciary a hunting license on the common law, making the positive law a matter of judicial discretion and allowing the courts to infringe upon the domain of the legislature and to ignore precedents. The common law consists of a myriad rules developed over many centuries involving great minds. It represents a fine web, the disturbance of which at one point may have severe unexpected consequences elsewhere. The new era makes extraordinary demands on judicial officers. The

Study of CPO resonances on the intercombination line in 173Yb

Science.gov (United States)

Kumar, Pushpander; Singh, Alok K.; Bharti, Vineet; Natarajan, Vasant; Pandey, Kanhaiya

2018-02-01

We study coherent population oscillations in an odd isotope of the two-electron atom Yb. The experiments are done using magnetic sublevels of the {F}g=5/2\\to {F}e=3/2 hyperfine transition in 173Yb of the {}1{{{S}}}0\\to {}3{{{P}}}1 intercombination line. The experiments are done both with and without an applied magnetic field. In the absence of an applied field, the complicated sublevel structure along with the saturated fluorescence effect causes the linewidth to be larger than the 190 kHz natural linewidth of the transition. In the presence of a field (of magnitude 330 mG), a well-defined quantization axis is present which results in the formation of two M-type systems. The total fluorescence is then limited by spin coherence among the ground sublevels. In addition, the pump beam gets detuned from resonance which results in a reduced scattering rate from the {}3{{{P}}}1 state. Both of these effects result in a reduction of the linewidth to a subnatural value of about 100 kHz.

40 CFR 421.332 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Science.gov (United States)

2010-07-01

... times. (d) SiCl4 purification wet air pollution control. BPT Limitations for the Primary Zirconium and...) Sand drying wet air pollution control. BPT Limitations for the Primary Zirconium and Hafnium... chlorination off-gas wet air pollution control. BPT Limitations for the Primary Zirconium and Hafnium...

Electrochemical-metallothermic reduction of zirconium in molten salt solutions

International Nuclear Information System (INIS)

McLaughlin, D.F.; Talko, F.

1990-01-01

This patent describes a method for separating hafnium from zirconium of the type wherein a feed containing zirconium and hafnium chlorides is prepared from zirconium-hafnium chloride and the feed is introduced into a distillation column, which distillation column has a reboiler connected at the bottom and a reflux condenser connected at the top and wherein a hafnium chloride enriched stream is taken from the top of the column and a zirconium enriched chloride stream is taken from the bottom of the column. It comprises: reducing the zirconium enriched chloride stream taken from the distillation column to metal by electrochemically reducing an alkaline earth metal in a molten salt bath with the molten salt in the molten salt bath consisting essentially of a mixture of at least one alkali metal chloride and at least one alkaline earth metal chloride and zirconium chloride, with the reduced alkaline earth metal reacting with the zirconium chloride to produce zirconium metal and alkaline earth metal chloride

41 CFR 302-9.173 - How many replacement POV's may my agency authorize me to transport to my post of duty at...

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 4 2010-07-01 2010-07-01 false How many replacement POV's may my agency authorize me to transport to my post of duty at Government expense? 302-9.173... How many replacement POV's may my agency authorize me to transport to my post of duty at Government...

Determination of hafnium at the 10−4% level (relative to zirconium content) using neutron activation analysis, inductively coupled plasma mass spectrometry and inductively coupled plasma atomic emission spectrometry

International Nuclear Information System (INIS)

Smolik, Marek; Polkowska-Motrenko, Halina; Hubicki, Zbigniew; Jakóbik-Kolon, Agata; Danko, Bożena

2014-01-01

Graphical abstract: -- Highlights: •We worked out ICP-MS method of Hf determination in Zr and Zr compounds. •We used NAA method as reference one. •We obtained pure zirconium matrix by ion exchange (Diphonix ® resin). •These permit to determine ≥1 × 10 −4 % Hf in Zr sample by ICP MS with good precision and accuracy. -- Abstract: Hafnium at the very low level of 1–8 ppm (in relation to zirconium) was determined in zirconium sulfate solutions (originating from investigations of the separation of ca. 44 ppm Hf from zirconium by means of the ion exchange method) by using three independent methods: inductively coupled plasma mass spectrometry (ICP MS), neutron activation analysis (NAA) and inductively coupled plasma atomic emission spectrometry (ICP-AES). The results of NAA and ICP MS determinations were consistent with each other across the entire investigated range (the RSD of both methods did not exceed 38%). The results of ICP-AES determination were more diverse, particularly at less than 5 ppm Hf (RSD was significantly higher: 29–253%). The ion exchange method exploiting Diphonix ® resin proved sufficient efficiency in Zr–Hf separation when the initial concentration ratio of the elements ([Zr] 0 /[Hf] 0 ) ranged from 1200 to ca. 143,000

Perturbed angular correlation

International Nuclear Information System (INIS)

Fabris, J.D.

1977-01-01

The electric quadrupolar interaction in some hafnium complexes, measured at the metal nucleus level is studied. For that purpose, the technique of γ-γ perturbed angular correlation is used: the frequencies of quadrupolar interaction are compared with some hafnium α-hydroxicarboxilates, namely glycolate, lactate, mandelate and benzylate; the influence of the temperature on the quadrupolar coupling on the hafnium tetramandelate is studied; finally, the effects associated with the capture of thermal neutrons by hafnium tetramandelate are examined locally at the nuclear level. The first group of results shows significant differences in a series of complexes derived from glycolic acid. On the other hand, the substitution of the protons in hafnium tetramandelate structure by some alkaline cations permits to verify a correlation between the variations in the quadrupolar coupling and the electronegativities of the substituent elements. Measurements at high temperatures show that this complex is thermally stable at 100 and 150 0 C. It is possible to see the appearance of two distinct sites for the probe nucleus, after heating the sample at 100 0 C for prolonged time. This fact is attributed to a probable interconversion among the postulated structural isomers for the octacoordinated compounds. Finally, measurements of angular correlation on the irradiated complex show that there is an effective destruction of the target molecule by neutron capture [pt

Use of the on-line Moessbauer effect as a contribution to the study of recoil defects in solids

International Nuclear Information System (INIS)

Jeandey, Christian

1974-01-01

This research thesis addresses the study of effects of nuclear reactions, also known as 'after-effects' such as atomic disorders resulted from atom recoil, but also possible chemical modifications. The author more particularly focuses of recoil defects. He reports a critical review of studies of structure defects (in pure metals, ordered alloys, ionic crystals) performed by using conventional resonance absorption, and then presents an analysis of results of the defect creation dynamics as it had been proposed by other authors. He also proposes an overview of the evolution and disappearance of defects during thermal treatments. After a review of experiments based on the on-line Moessbauer effect, the author reports the study of recoil effects in pure metals (iron, hafnium), in alloys (Fe 1-x Al x , FeGe 2 , cubic, monoclinic and hexagonal FeGe), and in organic complexes (ferrous oxalate, different types of hafnium chelate, hafnium oxide). He finally discusses the electronic properties of different types of iron and hafnium chelate in solid phase [fr

Grindability of cast Ti-Hf alloys.

Science.gov (United States)

Kikuchi, Masafumi; Takahashi, Masatoshi; Sato, Hideki; Okuno, Osamu; Nunn, Martha E; Okabe, Toru

2006-04-01

As part of our systematic studies characterizing the properties of titanium alloys, we investigated the grindability of a series of cast Ti-Hf alloys. Alloy buttons with hafnium concentrations up to 40 mass% were made using an argon-arc melting furnace. Each button was cast into a magnesia-based mold using a dental titanium casting machine; three specimens were made for each metal. Prior to testing, the hardened surface layer was removed. The specimens were ground at five different speeds for 1 min at 0.98 N using a carborundum wheel on an electric dental handpiece. Grindability was evaluated as the volume of metal removed per minute (grinding rate) and the volume ratio of metal removed compared to the wheel material lost (grinding ratio). The data were analyzed using ANOVA. A trend of increasing grindability was found with increasing amounts of hafnium, although there was no statistical difference in the grindability with increasing hafnium contents. We also found that hafnium may be used to harden or strengthen titanium without deteriorating the grindability.

The D173G mutation in ADAMTS-13 causes a severe form of congenital thrombotic thrombocytopenic purpura

KAUST Repository

Lancellotti, S.

2015-08-13

Congenital thrombotic thrombocytopenic purpura (TTP) is a rare form of thrombotic microangiopathy, inherited with autosomal recessive mode as a dysfunction or severe deficiency of ADAMTS-13 (A Disintegrin And Metalloprotease with ThromboSpondin 1 repeats Nr. 13), caused by mutations in the ADAMTS-13 gene. About 100 mutations of the ADAMTS-13 gene were identified so far, although only a few characterised by in vitro expression studies. A new Asp to Gly homozygous mutation at position 173 of ADAMTS-13 sequence was identified in a family of Romanian origin, with some members affected by clinical signs of TTP. In two male sons, this mutation caused a severe (< 3 %) deficiency of ADAMTS-13 activity and antigen level, associated with periodic thrombocytopenia, haemolytic anaemia and mild mental confusion. Both parents, who are cousins, showed the same mutation in heterozygous form. Expression studies of the mutant ADAMTS-13, performed in HEK293 cells, showed a severe decrease of the enzyme’s activity and secretion, although the protease was detected inside the cells. Molecular dynamics found that in the D173G mutant the interface area between the metalloprotease domain and the disintegrin-like domain significantly decreases during the simulations, while the proline-rich 20 residues linker region (LR, 285–304) between them undergoes extensive conformational changes. Inter-domain contacts are also significantly less conserved in the mutant compared to the wild-type. Both a decrease of the inter-domain contacts along with a substantial conformational rearrangement of LR interfere with the proper maturation and folding of the mutant ADAMTS-13, thus impairing its secretion.

The D173G mutation in ADAMTS-13 causes a severe form of congenital thrombotic thrombocytopenic purpura

KAUST Repository

Lancellotti, S.; Peyvandi, F.; Pagliari, M.; Cairo, A.; Abdel-Azeim, Safwat; Chermak, Edrisse; Lazzareschi, I.; Mastrangelo, S.; Cavallo, Luigi; Oliva, R.; De Cristofaro, R.

2015-01-01

Congenital thrombotic thrombocytopenic purpura (TTP) is a rare form of thrombotic microangiopathy, inherited with autosomal recessive mode as a dysfunction or severe deficiency of ADAMTS-13 (A Disintegrin And Metalloprotease with ThromboSpondin 1 repeats Nr. 13), caused by mutations in the ADAMTS-13 gene. About 100 mutations of the ADAMTS-13 gene were identified so far, although only a few characterised by in vitro expression studies. A new Asp to Gly homozygous mutation at position 173 of ADAMTS-13 sequence was identified in a family of Romanian origin, with some members affected by clinical signs of TTP. In two male sons, this mutation caused a severe (< 3 %) deficiency of ADAMTS-13 activity and antigen level, associated with periodic thrombocytopenia, haemolytic anaemia and mild mental confusion. Both parents, who are cousins, showed the same mutation in heterozygous form. Expression studies of the mutant ADAMTS-13, performed in HEK293 cells, showed a severe decrease of the enzyme’s activity and secretion, although the protease was detected inside the cells. Molecular dynamics found that in the D173G mutant the interface area between the metalloprotease domain and the disintegrin-like domain significantly decreases during the simulations, while the proline-rich 20 residues linker region (LR, 285–304) between them undergoes extensive conformational changes. Inter-domain contacts are also significantly less conserved in the mutant compared to the wild-type. Both a decrease of the inter-domain contacts along with a substantial conformational rearrangement of LR interfere with the proper maturation and folding of the mutant ADAMTS-13, thus impairing its secretion.

Macrophage Migration Inhibitory Factor Promoter Polymorphisms (−794 CATT5–8 and −173 G>C: Relationship with mRNA Expression and Soluble MIF Levels in Young Obese Subjects

Directory of Open Access Journals (Sweden)

Inés Matia-García

2015-01-01

Full Text Available We analyzed the relationship of −794 CATT5–8 and −173 G>C MIF polymorphisms with mRNA and soluble MIF in young obese subjects. A total of 250 young subjects, 150 normal-weight and 100 obese subjects, were recruited in the study. Genotyping of −794 CATT5–8 and −173 G>C MIF polymorphisms was performed by PCR and PCR-RFLP, respectively. MIF mRNA expression was determined by real-time PCR and serum MIF levels were measured using an ELISA kit. For both MIF promoter polymorphisms, no significant differences in the genotype and allele frequencies between groups were observed. MIF mRNA expression was slightly higher in obese subjects than in normal-weight subjects (1.38-fold, while soluble MIF levels did not show differences between groups. In addition, we found an increase in MIF mRNA expression in carriers of the 6,6 and C/C genotypes and the 6G haplotype of the −794 CATT5–8 and −173 G>C MIF polymorphisms, although it was not significant. In conclusion, this study found no relationship between obesity and MIF gene promoter polymorphisms with MIF mRNA expression in young obese subjects.

Laparoscopic Heller-Dor for primary esophageal achalasia: outcomes in 173 patients.

Science.gov (United States)

Rosati, Riccardo; Fumagalli Romario, Uberto; Ceolin, Martina; Massaron, Simonetta; Peracchia, Alberto

2013-01-01

Laparoscopic Heller myotomy combined with anterior (Dor) fundoplication is the most widely-used surgical procedure for treating esophageal achalasia in Europe From November 1992 through May 2010 we performed laparoscopic Heller-Dor on 173 patients Conversion to laparotomy was required in three cases (1.7%) at the beginning of the experience (for mucosal) perforation which was the most frequent intraoperative complication, managed laparoscopically with the increasing experience. Five (2.9%) cases had minor postoperative complications. Clinical results were satisfactory in 99.4% of cases. One patient (0.6%) had severe persistent dysphagia. Mean esophageal diameter decreased from 50 mm ± 12 (range 20- 90) to 25 mm ± 7 (range 15-80). Lower esophageal sphincter pressure decreased from 32 mmHg (median, range 10- 93) pre-operatively to 11 mmHg (median, range 5-21) at one year follow up and residual pressure from 12 mmHg (median, range 3-30) to 4 mmHg (median, range 1-8). Impedance and pH monitoring showed normal levels in 39/47 (83%) patients who agreed to testing. The good outcomes of this experience, in part due to careful adherence to technical aspects of the operation, confirm that the laparoscopic Heller-Dor is the gold standard surgical treatment for esophageal achalasia.

Radioisotopic heat source

Science.gov (United States)

Jones, G.J.; Selle, J.E.; Teaney, P.E.

1975-09-30

Disclosed is a radioisotopic heat source and method for a long life electrical generator. The source includes plutonium dioxide shards and yttrium or hafnium in a container of tantalum-tungsten-hafnium alloy, all being in a nickel alloy outer container, and subjected to heat treatment of from about 1570$sup 0$F to about 1720$sup 0$F for about one h. (auth)

High-spin nuclear target of 178m2Hf: creation and nuclear reaction studies

International Nuclear Information System (INIS)

Oganessyan, Yu.Ts.; Karamyan, S.A.; Gangrskij, Yu.P.

1993-01-01

A long-lived (31 years) four-quasiparticle isomer 178m 2 Hf(I,K π =16,16 + ) was produced in microweight quantities using the nuclear reaction 176 Yb( 4 He, 2n). Methods of precision chemistry and mass-separation for the purification of the produced Hf material have been developed. Thin targets of isomeric hafnium-178 on carbon backings were prepared and used in experiments on a neutron, proton and deuteron beams. First results on nuclear reactions on a high-spin exotic target were obtained. Experiments on electromagnetic interactions of the isomeric hafnium using methods of the collinear laser spectroscopy as well as of the nuclear orientation of hafnium implanted into a crystalline media were started. 11 refs.; 11 figs.; 2 tabs

New type of colour reactions of o,o'-dihydroxyazo compounds

International Nuclear Information System (INIS)

Dedkov, Yu.M.; Podvigina, T.I.

1977-01-01

It is shown that in the system: zirconium (hafnium)-picramine-epsilon (PE)-ethylrhodamine S (ERS), a heteroligand complex is formed, with an excess of the organic reagents, having the following ratio of components: Zr(Hf):PE:ERS=1:2:5. The molecules of ERS substitute the protons of free OH groups in binary complexes of zirconium (hafnium) with PE, while the excess molecules of ERS are added associatively. The resulting complex is floated off, the flotation product is dissolved in acetone, and its optical density is measured. The true molar extinction coefficient of the complex is equal to 6x10 5 , while the apparent one equals 3.2x10 5 . It is possible to determine submicroamounts of zirconium (hafnium) with preminary Ti and Nb masking

Fibroblast Growth Factor-23 and Vitamin D Metabolism in Subjects with eGFR ≥60 ml/min/1.73 m².

Science.gov (United States)

Nakatani, Shinya; Nakatani, Ayumi; Tsugawa, Naoko; Yamada, Shinsuke; Mori, Katsuhito; Imanishi, Yasuo; Ishimura, Eiji; Okano, Toshio; Inaba, Masaaki

2015-01-01

Fibroblast growth factor (FGF)-23 and parathyroid hormone (PTH) are both potent phosphaturic hormones. Since they exert opposite effects on vitamin D metabolism, the measurement of 3 vitamin D metabolites; 25-hydroxyvitamin D (25-OH-D), 1,25-dihydroxyvitamin D (1,25(OH)2D), and 24,25-dihydroxyvitamin D (24,25(OH)2D), allows the distinction of the effects of FGF-23 from those of PTH. The aim of this study was to elucidate which factor, FGF-23 or PTH, plays a more important role in the regulation of vitamin D metabolites in subjects with estimated glomerular filtration (eGFR) ≥60 ml/min/1.73 m(2). Subjects with eGFR ≥60 ml/min/1.73 m(2) (n = 20) were enrolled and their serum levels of FGF-23, intact PTH, and vitamin D metabolites were determined. Serum FGF-23 correlated inversely with 1,25(OH)2D (r = -0.717, p = 0.0004) and the 1,25(OH)2D/25-OH-D ratio (r = -0.518, p = 0.019), compared with a significant positive correlation between serum intact PTH and the 1,25(OH)2D/25-OH-D ratio (r = 0.562, p = 0.010). Multiple regression analyses revealed serum FGF-23 as a significant factor that was associated with serum 1,25(OH)2D (β = -0.593, p = 0.018), 1,25(OH)2D/25-OH-D ratio (β = -0.521, p = 0.025), and the 24,25(OH)2D/1,25(OH)2D ratio (β = 0.632, p = 0.008), and intact PTH as a significant factor associated with the 1,25(OH)2D/25-OH-D ratio (β = 0.445, p = 0.028). This study demonstrated that, even in subjects with eGFR ≥60 ml/min/1.73 m(2), FGF-23 might play an important role in the regulation of vitamin D metabolism. In addition to the established role of PTH, the association between FGF-23 and indices of vitamin D metabolism suggested the potential role of FGF-23 on phosphate metabolism in such patients. © 2015 S. Karger AG, Basel.

Evolution of E 2 transition strength in deformed hafnium isotopes from new measurements on 172Hf,174Hf, and 176Hf

Science.gov (United States)

Rudigier, M.; Nomura, K.; Dannhoff, M.; Gerst, R.-B.; Jolie, J.; Saed-Samii, N.; Stegemann, S.; Régis, J.-M.; Robledo, L. M.; Rodríguez-Guzmán, R.; Blazhev, A.; Fransen, Ch.; Warr, N.; Zell, K. O.

2015-04-01

Background: The available data for E 2 transition strengths in the region between neutron-deficient hafnium and platinum isotopes are far from complete. More and precise data are needed to enhance the picture of structure evolution in this region and to test state-of-the-art nuclear models. In a simple model, the maximum collectivity is expected at the middle of the major shell. However, for actual nuclei, particularly in heavy-mass regions, which should be highly complex, this picture may no longer be the case, and one should use a more realistic nuclear-structure model. We address this point by studying the spectroscopy of Hf as a representative case. Purpose: We remeasure the 21+ half-lives of 172,174,176Hf, for which there is some disagreement in the literature. The main goal is to measure, for the first time, the half-lives of higher-lying states of the rotational band. The new results are compared to a theoretical calculation for absolute transition strengths. Method: The half-lives were measured using γ -γ and conversion-electron-γ delayed coincidences with the fast timing method. For the determination of half-lives in the picosecond region, the generalized centroid difference method was applied. For the theoretical calculation of the spectroscopic properties, the interacting boson model is employed, whose Hamiltonian is determined based on microscopic energy-density functional calculations. Results: The measured 21+ half-lives disagree with results from earlier γ -γ fast timing measurements, but are in agreement with data from Coulomb excitation experiments and other methods. Half-lives of the 41+ and 61+ states were measured, as well as a lower limit for the 81+ states. Conclusions: This work shows the importance of a mass-dependent effective boson charge in the interacting boson model for the description of E 2 transition rates in chains of nuclei. It encourages further studies of the microscopic origin of this mass dependence. New experimental

Ceramic material suitable for repair of a space vehicle component in a microgravity and vacuum environment, method of making same, and method of repairing a space vehicle component

Science.gov (United States)

Riedell, James A. (Inventor); Easler, Timothy E. (Inventor)

2009-01-01

A precursor of a ceramic adhesive suitable for use in a vacuum, thermal, and microgravity environment. The precursor of the ceramic adhesive includes a silicon-based, preceramic polymer and at least one ceramic powder selected from the group consisting of aluminum oxide, aluminum nitride, boron carbide, boron oxide, boron nitride, hafnium boride, hafnium carbide, hafnium oxide, lithium aluminate, molybdenum silicide, niobium carbide, niobium nitride, silicon boride, silicon carbide, silicon oxide, silicon nitride, tin oxide, tantalum boride, tantalum carbide, tantalum oxide, tantalum nitride, titanium boride, titanium carbide, titanium oxide, titanium nitride, yttrium oxide, zirconium diboride, zirconium carbide, zirconium oxide, and zirconium silicate. Methods of forming the ceramic adhesive and of repairing a substrate in a vacuum and microgravity environment are also disclosed, as is a substrate repaired with the ceramic adhesive.

Effect of the consumption of a fermented dairy product containing Bifidobacterium lactis DN-173 010 on constipation in childhood: a multicentre randomised controlled trial (NTRTC: 1571).

Science.gov (United States)

Tabbers, Merit M; Chmielewska, Ania; Roseboom, Maaike G; Boudet, Claire; Perrin, Catherine; Szajewska, Hania; Benninga, Marc A

2009-03-18

Constipation is a frustrating symptom affecting 3% of children worldwide. Randomised controlled trials show that both polyethylene glycol and lactulose are effective in increasing defecation frequency in children with constipation. However, in 30-50%, these children reported abdominal pain, bloating, flatulence, diarrhoea, nausea and bad taste of the medication. Two recent studies have shown that the fermented dairy product containing Bifidobacterium lactis strain DN-173 010 is effective in increasing stool frequency in constipation-predominant irritable bowel syndrome patients with a defecation frequency fermented dairy product is effective in the treatment of constipated children with a defecation frequency fermented dairy product containing Bifidobacterium lactis DN-173 010 or a control product, twice a day, for 3 weeks. During the study all children are instructed to try to defecate on the toilet for 5-10 minutes after each meal (3 times a day) and daily complete a standardized bowel diary. Primary endpoint is stool frequency. Secondary endpoints are stool consistency, faecal incontinence frequency, pain during defecation, digestive symptoms (abdominal pain, flatulence), adverse effects (nausea, diarrhoea, bad taste) and intake of rescue medication (Bisacodyl). Rate of success and rate of responders are also evaluated, with success defined as > or = 3 bowel movements per week and or = 3 on the last week of product consumption. To demonstrate that the success percentage in the intervention group will be 35% and the success percentage in the control group (acidified milk without ferments, toilet training, bowel diary) will be 15%, with alpha 0.05 and power 80%, a total sample size of 160 patients was calculated. This study is aimed to show that the fermented dairy product containing Bifidobacterium lactis strain DN-173 010 is effective in increasing stool frequency after 3 weeks of product consumption in children with functional constipation and a defecation

Proton and O sup(2-) ion diffusion studied by γ-γ angular correlation and by impedance spectroscopy

International Nuclear Information System (INIS)

Oliveira Damasceno, O. de.

1988-01-01

The interaction of sup(181) Ta quadrupole momentum with electric field gradient was measured by perturbed angular correlation spectroscopy in polycrystalline samples of hafnium hydride and hafnium oxide. The measurements were done as function of the temperature, in cubic and tetragonal phases of hafnium hydride. In the cubic phase, spin relaxation effects related to proton diffusion with activation energy of 0.43 ± 0.05eV were observed, and in the tetragonal phase, the interaction was purely static. The hafnium oxide was studied in cubic phase stabilized by addition of calcium oxide or magnesium oxide. Relaxation effects probably due to O sup(2-) ion diffusion were verified. The protonic conduction in K H sub(2) PO sub(4) was studied by impedance spectroscopy, in pellets prepared by melting or powder compression using silver and platinum electrodes. In the case of silver electrodes, in the low frequency region, the impedance spectrum tends to a 45 sup(0) typical line of the diffusion process. It was attributed to hydrogen injection in the electrode. Heating k H sub(2) PO sub(4) at about 230 sup(0)C modifies significantly the electric properties. Two relaxation annealing reduced conductivities to constant values independently of preparation method. (author)

Lowering the environmental impact of high-kappa/ metal gate stack surface preparation processes

Science.gov (United States)

Zamani, Davoud

ABSTRACT Hafnium based oxides and silicates are promising high-κ dielectrics to replace SiO2 as gate material for state-of-the-art semiconductor devices. However, integrating these new high-κ materials into the existing complementary metal-oxide semiconductor (CMOS) process remains a challenge. One particular area of concern is the use of large amounts of HF during wet etching of hafnium based oxides and silicates. The patterning of thin films of these materials is accomplished by wet etching in HF solutions. The use of HF allows dissolution of hafnium as an anionic fluoride complex. Etch selectivity with respect to SiO2 is achieved by appropriately diluting the solutions and using slightly elevated temperatures. From an ESH point of view, it would be beneficial to develop methods which would lower the use of HF. The first objective of this study is to find new chemistries and developments of new wet etch methods to reduce fluoride consumption during wet etching of hafnium based high-κ materials. Another related issue with major environmental impact is the usage of large amounts of rinsing water for removal of HF in post-etch cleaning step. Both of these require a better understanding of the HF interaction with the high-κ surface during the etching, cleaning, and rinsing processes. During the rinse, the cleaning chemical is removed from the wafers. Ensuring optimal resource usage and cycle time during the rinse requires a sound understanding and quantitative description of the transport effects that dominate the removal rate of the cleaning chemicals from the surfaces. Multiple processes, such as desorption and re-adsorption, diffusion, migration and convection, all factor into the removal rate of the cleaning chemical during the rinse. Any of these processes can be the removal rate limiting process, the bottleneck of the rinse. In fact, the process limiting the removal rate generally changes as the rinse progresses, offering the opportunity to save resources

[Acute ethanol intoxication among children and adolescents. A retrospective analysis of 173 patients admitted to a university children hospital].

Science.gov (United States)

Schöberl, S; Nickel, P; Schmutzer, G; Siekmeyer, W; Kiess, W

2008-01-01

In the last time the alcohol consumption among children and adolescents is a big theme in all kind of media. The ethanol consumption among children and adolescents has risen during the last years, but also new hazardous drinking patterns like "binge-drinking" are increasing. These drinking episodes are responsible for many hospital presentations of children and adolescents with acute ethanol intoxication. This study is a retrospective analysis of 173 patients admitted to the university children hospital of Leipzig due to acute ethanol intoxication during the period 1998-2004. Investigated parameters were: socio-demographic factors, clinical presentation and management as well as quantity and type of alcohol. During the years 1998-2004 the rate of alcohol intoxicated patients in this study increased, from 1998-2003 at about 171.4%. Totally 173 patients with an average age of 14.5 years were admitted to the university children hospital. There were significantly more boys than girls. The mean blood alcohol concentration of these patients was 1.77%. Some of the patients had severe symptoms. 62 were unconscious, 2 were in coma and at least 3 patients had to be ventilated. A difference between socioeconomic groups could be observed by comparing the different school types. 44.8% of the patients went to the middle school. Furthermore 17 patients of this study had mental disorders or psychosocial problems and were therefore in psychological or psychiatric treatment. In this study a significant influence of social classes or psychosocial problems on alcohol consumption such as binge-drinking leading to acute ethanol intoxication could not be found. Alarming is the increasing number of ethanol intoxicated patients, the young age, the high measured blood ethanol concentrations and the severe symptoms of these patients. This is the reason why early and intensive prevention strategies are required.

Solvent extraction columns

International Nuclear Information System (INIS)

Middleton, P.; Smith, J.R.

1979-01-01

In pulsed columns for use in solvent extraction processes, e.g. the reprocessing of nuclear fuel, the horizontal perforated plates inside the column are separated by interplate spacers manufactured from metallic neutron absorbing material. The spacer may be in the form of a spiral or concentric circles separated by radial limbs, or may be of egg-box construction. Suitable neutron absorbing materials include stainless steel containing boron or gadolinium, hafnium metal or alloys of hafnium. (UK)

Effect of the consumption of a fermented dairy product containing Bifidobacterium lactis DN-173 010 on constipation in childhood: a multicentre randomised controlled trial (NTRTC: 1571

Directory of Open Access Journals (Sweden)

Perrin Catherine

2009-03-01

Full Text Available Abstract Background Constipation is a frustrating symptom affecting 3% of children worldwide. Randomised controlled trials show that both polyethylene glycol and lactulose are effective in increasing defecation frequency in children with constipation. However, in 30–50%, these children reported abdominal pain, bloating, flatulence, diarrhoea, nausea and bad taste of the medication. Two recent studies have shown that the fermented dairy product containing Bifidobacterium lactis strain DN-173 010 is effective in increasing stool frequency in constipation-predominant irritable bowel syndrome patients with a defecation frequency Methods/design It is a two nation (The Netherlands and Poland double-blind, placebo-controlled randomised multicentre trial in which 160 constipated children (age 3–16 years with a defecation frequency Bifidobacterium lactis DN-173 010 or a control product, twice a day, for 3 weeks. During the study all children are instructed to try to defecate on the toilet for 5–10 minutes after each meal (3 times a day and daily complete a standardized bowel diary. Primary endpoint is stool frequency. Secondary endpoints are stool consistency, faecal incontinence frequency, pain during defecation, digestive symptoms (abdominal pain, flatulence, adverse effects (nausea, diarrhoea, bad taste and intake of rescue medication (Bisacodyl. Rate of success and rate of responders are also evaluated, with success defined as ≥ 3 bowel movements per week and ≤1 faecal incontinence episode over the last 2 weeks of product consumption and responder defined as a subject reporting a stool frequency ≥ 3 on the last week of product consumption. To demonstrate that the success percentage in the intervention group will be 35% and the success percentage in the control group (acidified milk without ferments, toilet training, bowel diary will be 15%, with alpha 0.05 and power 80%, a total sample size of 160 patients was calculated. Conclusion This

Cobalt catalysts for the conversion of methanol and for Fischer-tropsch synthesis to produce hydrocarbons

International Nuclear Information System (INIS)

Mauldin, C.H.; Davis, S.M.; Arcuri, K.B.

1987-01-01

A regeneration stable catalyst is described for the conversion at reaction conditions of methanol or synthesis gas to liquid hydrocarbons which consists essentially of from about 2 percent to about 25 percent cobalt, based on the weight of the catalyst composition, composited with titania, or a titania-containing support, to which is added sufficient of a zirconium, hafnium, cerium, or uranium promoter to provide a weight ratio of the zirconium, hafnium, cerium, or uranium metal:cobalt greater than about 0.101:1

Application of energy-dispersive XRF technique in the hydrometallurgy study of local zircon

International Nuclear Information System (INIS)

Meor Yusoff Sulaiman; Kamaruddin Hussin; Azizan Aziz

1996-01-01

In this study, energy-dispersive X-ray Fluorescence (EDXR-F) was used to analyse the elemental composition of the starting zircon mineral associated elements in the leaching solution. Besides analysing the major elements i.e. of zirconium, silicon and hafnium, trace elemental analysis for iron, titanium and the naturally occurring radioactive element thorium and uranium are important in establishing the grades of Malaysian zircon. The technique was also used in determine the optimum conditions for zirconium and hafnium recovery during the leaching process

Reactive evaporation of low-defect density hafnia

International Nuclear Information System (INIS)

Chow, R.; Falabella, S.; Loomis, G.E.; Rainer, F.; Stolz, C.J.; Kozlowski, M.R.

1993-01-01

Motivation for this work includes observations at Lawrence Livermore National Laboratory of a correlation between laser damage thresholds and both the absorption and the nodular-defect density of coatings. Activated oxygen is used to increase the metal-oxidation kinetics at the coated surface during electron-beam deposition. A series of hafnia layers are made with various conditions: two μ-wave configuations, two sources (hafnium and hafnia), and two reactive oxygen pressures. Laser damage thresholds (1064-nm, 10-ns pulses), absorption (at 511 nm), and nodular-defect densities from these coatings are reported. The damage thresholds are observed to increase as the absorption of the coatings decreases. However, no significant increase in damage thresholds are observed with the coatings made from a low nodular-defect density source material (hafnium). Hafnia coatings can be made from hafnium sources that have lower nodular-defect densities, lower absorption, and damage thresholds that are comparable with coatings made from a conventional hafnia source

Study of N-cinnamoylphenylhydroxylaminate solubility in water and organic solvents

International Nuclear Information System (INIS)

Pilipenko, A.T.; Shpak, Eh.A.; Samchuk, A.I.

1975-01-01

The composition of complexes of N-cinnamoylphenylhydroxylamine with copper, cadmium, lead, indium, iron, gallium, titanium, zirconium, hafnium, niobium, tantalum, tungsten, molybdenum and vanadium was determined. The solubility products of the N-cinnamoylphenylhydroxylaminates of copper, cadmium, indium, gallium and iron were determined by the method of measuring the solubility of precipitates in acid. The solubility of N-cinnamoylphenylhydroxalaminates of cadmium, indium, iron, titanium, zirconium, hafnium, niobium, tantalum, vanadium, molybdenum and tungsten in organic solvents was studied. Two-phase constants for the stability of the complexes were calculated. (author)

Revisão radiológica de 173 casos consecutivos de paracoccidioidomicose Radiological review of 173 consecutive cases of paracoccidioidomycosis

Directory of Open Access Journals (Sweden)

Henrique Simão Trad

2006-06-01

Full Text Available OBJETIVO: Revisar e determinar a incidência dos achados radiológicos mais importantes da paracoccidioidomicose, e verificar as possíveis variantes de suas apresentações. MATERIAIS E MÉTODOS: Foram revistos 173 casos consecutivos de paracoccidioidomicose, atendidos no período de 1970 a 1980. Os estudos radiológicos direcionados a cada caso foram reanalisados por no mínimo dois radiologistas experientes. RESULTADOS: Foram encontrados 94 casos de acometimento pulmonar isolado e 38 de acometimento pulmonar associado a lesões ganglionares, viscerais, ósseas e à tuberculose. Sem envolvimento pulmonar foram encontrados 41 casos, com lesões intestinais, viscerais, ósseas ou combinadas. Os principais achados radiológicos da forma pulmonar foram opacidade intersticial reticular e nodular bilateral, seguida por consolidação, também bilateral. As formas visceral e intestinal apresentaram lesões predominantes no fígado, jejuno e íleo. Na forma ganglionar houve predominância do comprometimento difuso abdominal e periférico, e no ósseo, áreas de lise principalmente em ossos longos e clavícula. CONCLUSÃO: A paracoccidioidomicose é doença granulomatosa comum no Brasil, acometendo principalmente o pulmão, tendo como porta de entrada a inalação dos esporos do fungo. Outras formas desta doença, menos freqüentes ou raras, devem ser permanentemente lembradas no diagnóstico diferencial.OBJECTIVE: To determine the incidence of most significant radiological findings of paracoccidioidomycosis and to verify its possible variants. MATERIALS AND METHODS: One hundred and seventy-three cases of paracoccidioidomycosis presented between 1970 and 1980 were reviewed, including their radiological workup reanalysis by at least two experienced radiologists. RESULTS: Ninety-four cases were pulmonary only and 38 were pulmonary associated with ganglial, visceral and osseous lesions or in association with tuberculosis. There was no pulmonary

Experimental Observations of Nuclear Activity in Deuterated Materials Subjected to a Low-Energy Photon Beam

Science.gov (United States)

Steinetz, Bruce M.; Benyo, Theresa L.; Pines, Vladimir; Pines, Marianna; Forsley, Lawrence P.; Westmeyer, Paul A.; Chait, Arnon; Becks, Michael D.; Martin, Richard E.; Hendricks, Robert C.;

Aperture-time of oxygen-precursor for minimum silicon incorporation into the interface-layer in atomic layer deposition-grown HfO{sub 2}/Si nanofilms

Energy Technology Data Exchange (ETDEWEB)

Mani-Gonzalez, Pierre Giovanni [CINVESTAV-Unidad Querétaro, Querétaro 76230, Querétaro, Mexico and Departamento de Física y Matemáticas, Instituto de Ingeniería y Tecnología, Universidad Autónoma de Ciudad Juárez, Ave. Del Charro 450, Cd. Juárez C.P. 32310, Chihuahua (Mexico); Vazquez-Lepe, Milton Oswaldo [CINVESTAV-Unidad Querétaro, Querétaro 76230, Querétaro, Mexico and Departamento de Ingeniería de Proyectos, Universidad de Guadalajara, Guadalajara 45100, Jalisco (Mexico); Herrera-Gomez, Alberto, E-mail: aherrera@qro.cinvestav.mx [CINVESTAV-Unidad Querétaro, Querétaro 76230, Querétaro (Mexico)

2015-01-15

Hafnium oxide nanofilms were grown with atomic layer deposition on H-terminated Si (001) wafers employing tetrakis dimethyl amino hafnium (TDMA-Hf) and water as precursors. While the number of cycles (30) and the aperture-time for TDMA-Hf (0.08 s) were kept constant, the aperture-time (τ{sub H{sub 2O}}) for the oxidant-agent (H{sub 2}O) was varied from 0 to 0.10 s. The structure of the films was characterized with robust analysis employing angle-resolved x-ray photoelectron spectroscopy. In addition to a ∼1 nm hafnium oxide layer, a hafnium silicate interface layer, also ∼1 nm thick, is formed for τ{sub H{sub 2O}} > 0. The incorporation degree of silicon into the interface layer (i.e., the value of 1 − x in Hf{sub x}Si{sub 1−x}O{sub y}) shows a minimum of 0.32 for τ{sub H{sub 2O}} = 0.04 s. By employing the simultaneous method during peak-fitting analysis, it was possible to clearly resolve the contribution from the silicate and from oxide to the O 1s spectra, allowing for the assessment of the oxygen composition of each layer as a function of oxidant aperture time. The uncertainties of the peak areas and on the thickness and composition of the layers were calculated employing a rigorous approach.

Preparation of refractory cermet structures for lithium compatibility testing

Science.gov (United States)

Heestand, R. L.; Jones, R. A.; Wright, T. R.; Kizer, D. E.

1973-01-01

High-purity nitride and carbide cermets were synthesized for compatability testing in liquid lithium. A process was developed for the preparation of high-purity hafnium nitride powder, which was subsequently blended with tungsten powder or tantalum nitride and tungsten powders and fabricated into 3 in diameter billets by uniaxial hot pressing. Specimens were then cut from the billets for compatability testing. Similar processing techniques were applied to produce hafnium carbide and zirconium carbide cermets for use in the testing program. All billets produced were characterized with respect to chemistry, structure, density, and strength properties.

The vibrational spectra of some tetrachlorides in rare gas matrices with particular reference to the molecular shapes of ThCl4 and UCl4

International Nuclear Information System (INIS)

Arthers, S.A.; Beattie, I.R.

1984-01-01

Infrared spectra of tin, lead, hafnium, thorium, and uranium tetrachlorides isolated in inert gas matrices are reported. The results obtained for the tin, lead, and hafnium compounds follow the expected isotope patterns for a tetrahedral molecule except for the observation of additional weak features to high frequency of the all- 35 Cl isotopomers. By contrast for thorium tetrachloride the observed spectrum is not characteristic of a Tsub(d) molecule but can be fitted to a species with Csub(2v) symmetry. Similar results (although less detailed) were obtained for uranium tetrachloride. (author)

Metal oxide targets produced by the polymer-assisted deposition method

Energy Technology Data Exchange (ETDEWEB)

Garcia, Mitch A., E-mail: mitch@berkeley.ed [Department of Chemistry, Room 446 Latimer Hall, University of California Berkeley, Berkeley, CA 94720-1460 (United States); Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Ali, Mazhar N.; Chang, Noel N.; Parsons-Moss, T. [Department of Chemistry, Room 446 Latimer Hall, University of California Berkeley, Berkeley, CA 94720-1460 (United States); Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Ashby, Paul D. [Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Gates, Jacklyn M. [Department of Chemistry, Room 446 Latimer Hall, University of California Berkeley, Berkeley, CA 94720-1460 (United States); Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Stavsetra, Liv [Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States); Gregorich, Kenneth E.; Nitsche, Heino [Department of Chemistry, Room 446 Latimer Hall, University of California Berkeley, Berkeley, CA 94720-1460 (United States); Lawrence Berkeley National Laboratory, Berkeley, CA 94720 (United States)

2010-02-11

The polymer-assisted deposition (PAD) method was used to create crack-free homogenous metal oxide films for use as targets in nuclear science applications. Metal oxide films of europium, thulium, and hafnium were prepared as models for actinide oxides. Films produced by a single application of PAD were homogenous and uniform and ranged in thickness from 30 to 320 nm. Reapplication of the PAD method (six times) with a 10% by weight hafnium(IV) solution resulted in an equally homogeneous and uniform film with a total thickness of 600 nm.

Metal oxide targets produced by the polymer-assisted deposition method

International Nuclear Information System (INIS)

Garcia, Mitch A.; Ali, Mazhar N.; Chang, Noel N.; Parsons-Moss, T.; Ashby, Paul D.; Gates, Jacklyn M.; Stavsetra, Liv; Gregorich, Kenneth E.; Nitsche, Heino

2010-01-01

The polymer-assisted deposition (PAD) method was used to create crack-free homogenous metal oxide films for use as targets in nuclear science applications. Metal oxide films of europium, thulium, and hafnium were prepared as models for actinide oxides. Films produced by a single application of PAD were homogenous and uniform and ranged in thickness from 30 to 320 nm. Reapplication of the PAD method (six times) with a 10% by weight hafnium(IV) solution resulted in an equally homogeneous and uniform film with a total thickness of 600 nm.

Triangular flow of negative pions emitted in PbAu collisions at $\\sqrt{S_{NN}} = 17.3$ GeV

CERN Document Server

Adamová, D.

Differential triangular flow, $v_3(p_T)$, of negative pions is measured at $\\sqrt{s_{NN}}$= 17.3~GeV around midrapidity by the CERES/NA45 experiment at CERN in central PbAu collisions in the range 0-30\\% with a mean centrality of 5.5\\%. This is the first measurement of the triangular flow at SPS energies. The $p_T$ range extends from about 0.05~GeV/c to more than 2~GeV/c. The triangular flow magnitude, corrected for the HBT effects, is smaller by a factor of about 2 than the one measured by the PHENIX experiment at RHIC and the ALICE experiment at the LHC. Within the analyzed range of central collisions no significant centrality dependence is observed. The data are found to be well described by a viscous hydro calculation combined with an UrQMD cascade model for the late stages.

Evaluation of T-111 forced-convection loop tested with lithium at 13700C

International Nuclear Information System (INIS)

DeVan, J.H.; Long, E.L. Jr.

1975-04-01

A T-111 alloy (Ta--8 percent W--2 percent Hf) forced-convection loop containing molten lithium was operated 3000 h at a maximum temperature of 1370 0 C. Flow velocities up to 6.3 m/s were used. The results obtained in this forced-convection loop are very similar to those observed in lower velocity thermal-convection loops of T-111 containing lithium. Weight changes were determined at 93 positions around the loop. The maximum dissolution rate occurred at the maximum wall temperature of the loop and was less than 1.3 μ m/year. Mass transfer of hafnium, nitrogen, and, to a lesser extent, carbon occurred from the hotter to cooler regions. Exposed surfaces in the highest temperature region were found to be depleted in hafnium to a depth of 60 μ m with no detectable change in tungsten content. There was some loss in room-temperature tensile strength for specimens exposed to lithium at 1370 0 C, attributable to depletion of hafnium and nitrogen and to attendant grain growth. (U.S.)

Separation of zirconium and hafnium; Separation du zirconium et de l'hafnium

Energy Technology Data Exchange (ETDEWEB)

Saint-James, D [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1959-07-01

This account is more chemical than metallurgical in character. The reason for this is that so-called 'nuclear metal' must fulfil standards of purity which only chemical processes can attain. This paper must therefore be considered as a preliminary study, from which the metallurgists can form an idea of the treatments leading to the production of the metal. (author) [French] Cet expose a un caractere chimique plutot que metallurgique. La raison en est que le metal dit 'nucleaire' a des exigences de purete que seuls des processus chimiques peuvent satisfaire. Il faut donc considerer cet expose comme un preliminaire, permettant de donner une idee aux metallurgistes des traitements qui aboutissent a l'elaboration du metal. (auteur)

Triangular flow of negative pions emitted in PbAu collisions at √{sNN} = 17.3 GeV

Science.gov (United States)

Adamová, D.; Agakichiev, G.; Andronic, A.; Antończyk, D.; Appelshäuser, H.; Belaga, V.; Bielčíková, J.; Braun-Munzinger, P.; Busch, O.; Cherlin, A.; Damjanović, S.; Dietel, T.; Dietrich, L.; Drees, A.; Dubitzky, W.; Esumi, S. I.; Filimonov, K.; Fomenko, K.; Fraenkel, Z.; Garabatos, C.; Glässel, P.; Hering, G.; Holeczek, J.; Kalisky, M.; Karpenko, Iu.; Krobath, G.; Kushpil, V.; Maas, A.; Marín, A.; Milošević, J.; Miśkowiec, D.; Panebrattsev, Y.; Petchenova, O.; Petráček, V.; Radomski, S.; Rak, J.; Ravinovich, I.; Rehak, P.; Sako, H.; Schmitz, W.; Schuchmann, S.; Sedykh, S.; Shimansky, S.; Stachel, J.; Šumbera, M.; Tilsner, H.; Tserruya, I.; Tsiledakis, G.; Wessels, J. P.; Wienold, T.; Wurm, J. P.; Yurevich, S.; Yurevich, V.

2017-01-01

Differential triangular flow, v3 (pT), of negative pions is measured at √{sNN} = 17.3 GeV around midrapidity by the CERES/NA45 experiment at CERN in central PbAu collisions in the range 0-30% with a mean centrality of 5.5%. This is the first measurement as a function of transverse momentum of the triangular flow at SPS energies. The pT range extends from about 0.05 GeV/c to more than 2 GeV/c. The triangular flow magnitude, corrected for the HBT effects, is smaller by a factor of about 2 than the one measured by the PHENIX experiment at RHIC and the ALICE experiment at the LHC. Within the analyzed range of central collisions no significant centrality dependence is observed. The data are found to be well described by a viscous hydrodynamic calculation combined with an UrQMD cascade model for the late stages.

Point defect engineering strategies to retard phosphorous diffusion in germanium

KAUST Repository

Tahini, H. A.; Chroneos, Alexander I.; Grimes, Robin W.; Schwingenschlö gl, Udo; Bracht, Hartmut A.

2013-01-01

The diffusion of phosphorous in germanium is very fast, requiring point defect engineering strategies to retard it in support of technological application. Density functional theory corroborated with hybrid density functional calculations are used to investigate the influence of the isovalent codopants tin and hafnium in the migration of phosphorous via the vacancy-mediated diffusion process. The migration energy barriers for phosphorous are increased significantly in the presence of oversized isovalent codopants. Therefore, it is proposed that tin and in particular hafnium codoping are efficient point defect engineering strategies to retard phosphorous migration. © the Owner Societies 2013.

PRODUCTION OF HAFNIUM METAL

Science.gov (United States)

Elger, G.W.; Boubel, R.W.

1963-01-01

This patent deals with a process of producing pure Hf metal from oxygen- contaminated gaseous Hf chloride. The oxygen compounds in the chioride gas are halogenated by contacting the gas at elevated temperature with Cl/sub 2/ in the presence of C. The Hf chloride, still in gaseous form, is contacted with molten Mg whereby Hf metal is formed and condensed on the Mg. (AEC)

MIVOC method at the mVINIS ion source

Directory of Open Access Journals (Sweden)

Jovović Jovica

2007-01-01

Full Text Available Based on the metal-ions-from-volatile-compounds (MIVOC method with the mVINIS ion source, we have produced multiply charged ion beams from solid substances. Highly in tense, stable multiply charged ion beams of several solid substances with high melting points were extracted by using this method. The spectrum of multiply charged ion beams obtained from the element hafnium is presented here. For the first time ever, hafnium ion beam spectra were recorded at an electron cyclotron resonance ion source. Multiply charged ion beams from solid substances were used to irradiate the polymer, fullerene and glassy carbon samples at the channel for the modification of materials.

Thickness independent reduced forming voltage in oxygen engineered HfO{sub 2} based resistive switching memories

Energy Technology Data Exchange (ETDEWEB)

Sharath, S. U., E-mail: sharath@oxide.tu-darmstadt.de; Kurian, J.; Komissinskiy, P.; Hildebrandt, E.; Alff, L. [Institute of Materials Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany); Bertaud, T.; Walczyk, C.; Calka, P. [IHP, Im Technologiepark 25, 15236 Frankfurt Oder (Germany); Schroeder, T. [IHP, Im Technologiepark 25, 15236 Frankfurt Oder (Germany); Brandenburgische Technische Universität, Konrad-Zuse-Strasse 1, 03046 Cottbus (Germany)

2014-08-18

The conducting filament forming voltage of stoichiometric hafnium oxide based resistive switching layers increases linearly with layer thickness. Using strongly reduced oxygen deficient hafnium oxide thin films grown on polycrystalline TiN/Si(001) substrates, the thickness dependence of the forming voltage is strongly suppressed. Instead, an almost constant forming voltage of about 3 V is observed up to 200 nm layer thickness. This effect suggests that filament formation and switching occurs for all samples in an oxidized HfO{sub 2} surface layer of a few nanometer thickness while the highly oxygen deficient thin film itself merely serves as a oxygen vacancy reservoir.

Characterization of electron beam deposited thin films of HfO2 and binary thin films of (HfO2:SiO2) by XRD and EXAFS measurements

International Nuclear Information System (INIS)

Das, N.C.; Sahoo, N.K.; Bhattacharyya, D.; Thakur, S.; Kamble, N.M.; Nanda, D.; Hazra, S.; Bal, J.K.; Lee, J.F.; Tai, Y.L.; Hsieh, C.A.

2009-10-01

In this report, we have discussed the microstructure and the local structure of composite thin films having varying hafnia and silica compositions and prepared by reactive electron beam evaporation. XRD and EXAFS studies have confirmed that the pure hafnium oxide thin film has crystalline microstructure whereas the films with finite hafnia and silica composition are amorphous. The result of EXAFS analysis has shown that the bond lengths as well as coordination numbers around hafnium atom change with the variation of hafnia and silica compositions in the thin film. Finally, change of bond lengths has been correlated with change of refractive index and band gap of the composite thin films. (author)

Effect of zirconium purity on the glass-forming-ability and notch toughness of Cu{sub 43}Zr{sub 43}Al{sub 7}Be{sub 7}

Energy Technology Data Exchange (ETDEWEB)

Andersen, Laura M. [Department of NanoEngineering, University of California, San Diego, 9500 Gilman Drive, La Jolla, CA (United States); Hofmann, Douglas C. [Materials Development and Manufacturing Technology Group, NASA Jet Propulsion Laboratory/California Institute of Technology, MS 18-105, 4800 Oak Grove Dr. Pasadena, CA 91109 (United States); Vecchio, Kenneth S., E-mail: kvecchio@ucsd.edu [Department of NanoEngineering, University of California, San Diego, 9500 Gilman Drive, La Jolla, CA (United States)

2016-09-30

The effect of substituting standard grade zirconium lump (99.8% excluding up to 4% hafnium) for high purity zirconium crystal bar (99.5%) in a Cu{sub 43}Zr{sub 43}Al{sub 7}Be{sub 7} bulk metallic glass (BMG) is examined. The final hafnium content in the BMG specimens was found to range from 0 to 0.44 at%. Introducing low purity zirconium significantly decreased the glass-forming-ability and reduced the notch toughness of the BMG. In contrast, when adding high purity hafnium to Cu{sub 43}Zr{sub 43}Al{sub 7}Be{sub 7} made with high purity zirconium, no significant change in the glass-forming-ability or toughness was observed. This suggests that the introduction of low purity zirconium in BMGs creates a more complex response than a simple addition of hafnium. It is likely that other impurities in the material, such as oxygen, play a role in the complex crystallization kinetics and change in mechanical properties. The notch toughness was measured through four-point-bend tests, which showed a decrease in notch toughness from an average of ~53 MPa m{sup 1/2} for the high purity samples to an average of ~29 MPa m{sup 1/2} with full substitution of low purity zirconium. A similar decrease in glass-forming-ability and toughness is observed in commercially synthesized high purity Cu{sub 43}Zr{sub 43}Al{sub 7}Be{sub 7}. The large scale commercial process is expected to introduced some unintentional impurities, which decrease the properties of the BMG in the same way as the lower purity elements. Lastly, Weibull statistics are used to provide an analysis of variability in toughness for both ingots synthesized in a small laboratory arc-melter and those synthesized commercially.

Development of new extraction agents for separation of rare radioactive elements

International Nuclear Information System (INIS)

Hala, J.; Navratil, O.; Prihoda, J.; Smola, J.

1977-01-01

Certain transition elements, such as rhodium and palladium may be recovered from waste solutions produced in spent fuel reprocessing. The extraction of palladium was studied using sulfur compounds of the sulfide and sulfoxide types and the effects were investigated of the individual factors on palladium distribution between the aqueous and the organic phases. The possibility of separating hafnium in the form of extractable complexes was tested on several systems. Studied in more detail were mainly the complexes of hafnium with pyrocatechol violet, xylenol orange, and tributyl phosphate. The extraction of other metals, mainly of scandium, europium and indium was investigated in detail in the system acid aqueous phase - organophosphinic acids solution in benzene. (L.K.)

MIF functional polymorphisms (-794 CATT5-8 and -173 G>C) are associated with MIF serum levels, severity and progression in male multiple sclerosis from western Mexican population.

Science.gov (United States)

Castañeda-Moreno, V A; De la Cruz-Mosso, U; Torres-Carrillo, N; Macías-Islas, M A; Padilla-De la Torre, O; Mireles-Ramírez, M A; González-Pérez, O; Ruiz-Sandoval, J L; Huerta, M; Trujillo, X; Ortuño-Sahagún, D; Jf, Muñoz-Valle

2018-07-15

Macrophage migration inhibitory factor (MIF) is a cytokine associated with tissue damage in multiple autoimmune diseases such as systemic lupus erythematosus, rheumatoid arthritis and psoriatic arthritis. The role of MIF in multiple sclerosis (MS) and the contribution of its polymorphisms are unknown in our population. Therefore, we decided to investigate the genetic association of -794 CATT 5-8 (rs5844572) and -173 G>C (rs755622) MIF polymorphisms with MS, clinical variables and MIF serum levels in the population of western Mexico. 230 MS patients diagnosed according to McDonald criteria and 248 control subjects (CS) were recruited for this study, both polymorphisms were genotyped by PCR and PCR-RFLP and MIF serum levels were measured by ELISA kit. Severity and progression of MS were evaluated by EDSS and MSSS scores, respectively. Genotypes carrying the 5 repeats alleles of -794 CATT 5-8 MIF polymorphism present higher MIF serum levels in comparison with no carriers, and the presence of 5,7 heterozygous genotype contribute to the increase of disease severity and damage progression in MS patients. Notably when we stratified by sex, an effect of risk alleles (7 repeats and -173*C) of both MIF polymorphisms on EDSS and MSSS scores on males was found (p < 0.01). This study suggests that polymorphic alleles of MIF polymorphisms could act as sex-specific disease modifiers that increase the severity and progression of MS in male Mexican-Mestizo western population. Copyright © 2018 Elsevier B.V. All rights reserved.

Production of lipopeptides by Bacillus amyloliquefaciens XZ-173 in solid state fermentation using soybean flour and rice straw as the substrate.

Science.gov (United States)

Zhu, Zhen; Zhang, Guoyi; Luo, Yi; Ran, Wei; Shen, Qirong

2012-05-01

This work was aimed to produce lipopeptides by Bacillus amyloliquefaciens XZ-173 in solid state fermentation using agro-industrial byproducts. A central composite design was used to get the highest lipopeptides production. Results revealed that the optimal conditions for maximum lipopeptides production were 1.79% starch and 1.91% yeast extract by employing 5.58 g soybean flour and 3.67 g rice straw as the solid substrate with initial pH 7.5, moisture content 55% and a 10% inoculum level at 30°C for 2 days. Under these conditions, the experimental yield of lipopeptides reached 50.01 mg/gds, which was very close to the predicted value (49.91 mg/gds). At high concentration, the lipopeptides extracted from fermented substrates showed strong antibiotic activity against Rhizoctonia solani and Ralstonia solanacearum and certain emulsification but good emulsion stability. This is the first report on lipopeptides production that uses rice straw as a major substrate. Copyright © 2012 Elsevier Ltd. All rights reserved.

Novel Manufacturing Process for Unique Mixed Carbide Refractory Composites, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This STTR Phase I project will establish the feasibility of an innovative manufacturing process to fabricate a range of unique hafnium/silicon based carbide...

Cobalt catalysts, and use thereof for the conversion of methanol and for fischer-tropsch synthesis, to produce hydrocarbons

International Nuclear Information System (INIS)

Mauldin, C.H.; Davis, S.M.; Arcuri, K.B.

1988-01-01

This patent describes a process useful for the conversion of methanol to hydrocarbons which comprises contacting the methanol at reaction conditions with a catalyst which comprises from about 2 percent to about 25 percent cobalt, based on the weight of the catalyst composition, composited with titania, or a titania-containing support, to which is added a zirconium, hafnium, cerium, or uranium promoter, the weight ratio of the zirconium, hafnium, cerium, or uranium metal:cobalt being greater than about 0.010:1; the reaction conditions being defined within ranges as follows: Methanol:H/sub 2/ ratio: greater than about 4:1, Space Velocities, Hr/sup -1/:about 0.1 to 10, Temperatures, 0 C.:about 150 to 350, Methanol Partial Pressure, psia: about 100 to 1000

Ceramic component for M.H.D electrode

International Nuclear Information System (INIS)

Marchant, D.D.; Bates, J.L.

1980-01-01

A ceramic component which exhibits electrical conductivity down to near room temperatures has the formula: Hfsub(x)Insub(y)Asub(z)O 2 where x = 0.1 to 0.4, y = 0.3 to 0.6, z = 0.1 to 0.4 and A is a rare earth or yttrium. The rare earth may be Yb, Tb, Pr or Ce. The component is suitable for use in the fabrication of MHD electrodes or as the current lead-out portion of a composite electrode with other ceramic components. An MHD electrode comprises a cap of a known ceramic, e.g. stabilised zirconium or hafnium oxide or terbium stabilised hafnium, a current lead-out ceramic according to the invention, and a copper frame. (author)

BITUMINOUS MIX RESPONSE TO PLASTIC DEFORMATIONS: COMPARISON OF THE SPANISH NLT-173 AND UNE-EN 12697-22 WHEEL-TRACKING TESTS

Directory of Open Access Journals (Sweden)

GEMA GARCÍA-TRAVÉ

2012-01-01

Full Text Available La formación de roderas es uno de los mayores deterioros que se producen en los firmes flexibles, lo que ocasiona la pérdida de regularidad superficial que repercute de forma negativa en la calidad del servicio prestado a los usuarios. Existen distintos ensayos de laboratorio que permiten evaluar las deformaciones plásticas producidas en las capas del pavimento, entre ellos podemos destacar los ensayos de simulación. El objetivo de esta investigación es analizar el comportamiento de una mezcla bituminosa en caliente frente a deformaciones plásticas, mediante dos métodos de ensayo diferentes; ensayo en pista de laboratorio de acuerdo a la normativa española NLT-173 y el ensayo de rodadura UNE-EN 12697-22 (ensayo obligatorio tras la entrada en vigor del Marcado CE de mezclas bituminosas en 2008. La finalidad última de este artículo es formular una propuesta de modificación de la normativa española (PG-3 sobre los límites exigibles en éste último ensayo.

40 CFR 302.6 - Notification requirements.

Science.gov (United States)

2010-07-01

..., phosphate, tin, zircon, hafnium, vanadium, monazite, and rare earth mines. Land disturbance incidental to..., chromium, copper, lead, nickel, selenium, silver, thallium, or zinc is not required if the mean diameter of...

Evaluation of the 175Lu(n,2n)174Lu, 175Lu(n,2n/sup 174m/Lu, and 175Lu(n,3n)173Lu cross sections from threshold to 20 MeV

International Nuclear Information System (INIS)

Philis, C.; Young, P.G.; Arthur, E.D.

1978-04-01

An evaluation of the 175 Lu(n,2n) 174 Lu, 175 Lu(n,2n)/sup 174m/Lu, and 175 Lu(n,3n) 173 Lu reactions from threshold to 20 MeV is presented. Available experimental data were renormalized to a consistent set of standards and were used along with results from statistical-preequilibrium model calculations to produce recommended curves for each of these reactions

Electrochemical investigations of ion-implanted oxide films

International Nuclear Information System (INIS)

Schultze, J.W.; Danzfuss, B.; Meyer, O.; Stimming, U.

1985-01-01

Oxide films (passive films) of 40-50 nm thickness were prepared by anodic polarization of hafnium and titanium electrodes up to 20 V. Multiple-energy ion implantation of palladium, iron and xenon was used in order to obtain modified films with constant concentration profiles of the implanted ions. Rutherford backscattering, X-ray photoelectron spectroscopy measurements and electrochemical charging curves prove the presence of implanted ions, but electrochemical and photoelectrochemical measurements indicate that the dominating effect of ion implantation is the disordering of the oxide film. The capacity of hafnium electrodes increases as a result of an increase in the dielectric constant D. For titanium the Schottky-Mott analysis shows that ion implantation causes an increase in D and the donor concentration N. Additional electronic states in the band gap which are created by the implantation improve the conductivity of the semiconducting or insulating films. This is seen in the enhancement of electron transfer reactions and its disappearance during repassivation and annealing. Energy changes in the band gap are derived from photoelectrochemical measurements; the absorption edge of hafnium oxide films decreases by approximately 2 eV because of ion implantation, but it stays almost constant for titanium oxide films. All changes in electrochemical behavior caused by ion implantation show little variation with the nature of the implanted ion. Hence the dominating effect seems to be a disordering of the oxide. (Auth.)

Microstructural characterization of as-cast hf-b alloys

Directory of Open Access Journals (Sweden)

João Carlos Jânio Gigolotti

2012-04-01

Full Text Available An accurate knowledge of several metal-boron phase diagrams is important to evaluation of higher order systems such as metal-silicon-boron ternaries. The refinement and reassessment of phase diagram data is a continuous work, thus the reevaluation of metal-boron systems provides the possibility to confirm previous data from an investigation using higher purity materials and better analytical techniques. This work presents results of rigorous microstructural characterization of as-cast hafnium-boron alloys which are significant to assess the liquid composition associated to most of the invariant reactions of this system. Alloys were prepared by arc melting high purity hafnium (minimum 99.8% and boron (minimum 99.5% slices under argon atmosphere in water-cooled copper crucible with non consumable tungsten electrode and titanium getter. The phases were identified by scanning electron microscopy, using back-scattered electron image mode and X-ray diffraction. In general, a good agreement was found between our data and those from the currently accepted Hafnium-Boron phase diagram. The phases identified are αHfSS and B-RhomSS, the intermediate compounds HfB and HfB2 and the liquide L. The reactions are the eutectic L ⇔ αHfSS + HfB and L ⇔ HfB2 + B-Rhom, the peritectic L + HfB2 ⇔ HfB and the congruent formation of HfB2.

WWER-440 local power peaking experiment with/without Hf inserts in the LR-0 reactor

International Nuclear Information System (INIS)

Josek, R.; Hudec, F.; Rypar, V.

2006-01-01

One of the known issues of the WWER-440 reactors is the control rod coupler induced power peaking in the neighbouring fuel assemblies. The effect has been discovered some years ago and is believed to be the cause of several fuel failures during operation in WWER-440 reactors. The effect itself is due to over-moderation and small absorption in the region of control rod coupler, leading to increase in thermal neutron flux and hence to power flare-up in the neighbouring fuel pins. The fuel vendor tackled the problem by attaching hafnium inserts on the inside of the control assembly box. The experiment performed in the LR-0 reactor was focused on the axial and radial power profiles in the vicinity of the control assembly with and without the hafnium inserts. The results of measurements with zero boron concentration are presented. The hafnium insert causes a decrease in peaking factor of about 30% in selected pins close to the control assembly. The measurements are compared with calculations performed with the MCNP-4C code. The compared variables are: the axial fission density distributions; peking factors and peaking factor decrease due to Hf insert. The MCNP results are accurate with respect to the experimental results. A series of benchmarks is being prepared on the basis of these measurements

Design of thermoelectrically highly efficient Heusler compounds using phase separations and nano-composites under an economic point of view

Science.gov (United States)

Balke, Benjamin

Half-Heusler (HH) compounds are one of the most promising candidates for thermoelectric materials for automotive and industrial waste heat recovery applications. In this talk, I will give an overview about our recent investigations of phase separations in HH thermoelectrics, focusing on the ternary system TiNiSn-ZrNiSn-HfNiSn. I will show how we adapted this knowledge to design a p-type HH compound which exhibits a ZT that is increased by 130% compared to the best published bulk p-type Heusler. I will also present how we used the phase separation to design thermoelectric highly efficient nano-composites of different single-phase materials. Since the price for Hafnium doubled within the last year, our research focused on the design of HH compounds without Hafnium. I will present a very recent calculation on ZT per Euro and efficiency per Euro for various materials followed by our latest very promising results for n-type Heusler compunds without Hafnium resulting in 20 times higher ZT/Euro values. These results strongly underline the importance of phase separations as a powerful tool for designing highly efficient materials for thermoelectric applications that fulfill the industrial demands for a thermoelectric converter. The author gratefully acknowledges financial support by the thermoHEUSLER2 Project (Project No. 19U15006F) of the German Federal Ministry of Economics and Technology (BMWi).

Energy dependence of particle ratio fluctuations in central Pb+Pb collisions from $\\sqrt{s_{_{NN}}} =$~6.3 to 17.3 GeV

CERN Document Server

Alt, C; Baatar, B; Barna, D; Bartke, J; Betev, L; Bialkowska, H; Blume, C; Boimska, B; Botje, M; Bracinik, J; Bramm, R; Bunccic, P; Cerny, V; Christakoglou, P; Chvala, O; Cramer, J G; Csató, P; Dinkelaker, P; Eckardt, V; Flierl, D; Fodor, Z; Foka, P; Friese, V; Gál, J; Gazdzicki, M; Genchev, V; Georgopoulos, G; Gladysz, E; Grebieszkow, K; Hegyi, S; Höhne, C; Kadija, K; Karev, A; Kliemant, M; Kniege, S; Kolesnikov, V I; Kornas, E; Korus, R; Kowalski, M; Kraus, I; Kreps, M; Kresan, D; Van Leeuwen, M; Lévai, P; Litov, L; Lungwitz, B; Makariev, M; Malakhov, A I; Mateev, M; Melkumov, G L; Mischke, A; Mitrovski, M; Molnár, J; Mrówczynski, St; Nicolic, V; Pálla, G; Panagiotou, A D; Panayotov, D; Petridis, A; Pikna, M; Prindle, D; Pühlhofer, F; Renfordt, R; Roland, C; Roland, G; Rybczynski, M; Rybicki, A; Sandoval, A; Schmitz, N; Schuster, T; Seyboth, P; Siklér, F; Sitár, B; Skrzypczak, E; Stefanek, G; Stock, R; Ströbele, H; Susa, T; Szentpétery, I; Sziklai, J; Szymanski, P; Trubnikov, V; Varga, D; Vassiliou, M; Veres, G I; Vesztergombi, G; Vranic, D; Wetzler, A; Wlodarczyk, Z; Yoo, I K

2009-01-01

We present recent measurements of the energy dependence of event-by-event fluctuations in the K/pi and (p + \\bar{p})/pi multiplicity ratios in heavy ion collisions at the CERN SPS. The particle ratio fluctuations were obtained for central Pb+Pb collisions at five collision energies, \\sqrt{s_{_{NN}}}, between 6.3 and 17.3 GeV. After accounting for the effects of finite-number statistics and detector resolution, we extract the strength of non-statistical fluctuations at each energy. For the K/pi ratio, larger fluctuations than expected for independent particle production are found at all collision energies. The fluctuations in the (p + \\bar{p})/pi ratio are smaller than expectations from independent particle production, indicating correlated pion and proton production from resonance decays. For both ratios, the deviation from purely statistical fluctuations shows an increase towards lower collision energies. The results are compared to transport model calculations, which fail to describe the energy dependence o...

Mesoporous TiO2 powders as host matrices for iron nanoparticles. Effect of the preparation procedure and doping with Hf

Czech Academy of Sciences Publication Activity Database

Dimitrov, M.; Ivanova, R.; Velinov, N.; Henych, Jiří; Slušná, Michaela; Štengl, Václav; Tolasz, Jakub; Mitov, I.; Tsoncheva, T.

2016-01-01

Roč. 7, JUL (2016), s. 56-63 ISSN 2352-507X Institutional support: RVO:61388980 Keywords : Mesoporous titania * Hafnium doping * Iron modification * Ethyl acetate oxidation * Methanol decomposition Subject RIV: CA - Inorganic Chemistry

Cathodoluminescence of Irradiated Hafnium Dioxide

Science.gov (United States)

2011-03-01

Martin and Michael Rhoby for their hard work in fixing assorted problems that cropped up during the course of my thesis work. Emily A. Purcell...Cathodoluminescence Microscopy of Inorganic Solids. New York: Plenum Press, 1990. [13] D. Drouin, A. R. Couture, D. Joly , X. Tastet, V. Aimez and R. Gauvin

Zirconium Zr and hafnium Hf

International Nuclear Information System (INIS)

Busev, A.I.; Tiptsova, V.G.; Ivanov, V.M.

1978-01-01

The basic methods for extracting and determining Zr(4) and Hf(4) are described. Diantipyrinemethane and its alkyl homologs selectively extract Zr and Hf from HNO 3 solutions in the presence of nitrates. Zr is selectively extracted with tetraethyldiamide of heptyl phosphoric acid (in benzene) as well as with 2-thenoyltrifluoroacetone (in an acid). The latter reagents is suitable for rapid determination of 95 Zr in a mixture with 95 Nb and other fragments. The complexometric determination of Zr is based on formation of a stable complex of Zr with EDTA. The titration is carried out in the presence of n-sulfobenzene-azo-pyrocatechol, eriochrome black T. The determination is hindered by Hf, fluoride-, phosphate-, oxalate- and tartrate-ions. The method is used for determining Zr in zircon and eudialyte ore. Zr is determined photometrically with the aid of xylenol orange, arsenazo 3 and pyrocatechol violet (in phosphorites). Hf is determined in the presence of Zr photometrically with the aid of xylenol orange or methyl-thymol blue. The method is based on Zr being masked with hydrogen peroxide in the presence of sulfate-ions

Alkali metal hafnium oxide scintillators

Science.gov (United States)

Bourret-Courchesne, Edith; Derenzo, Stephen E.; Taylor, Scott Edward

2018-05-08

The present invention provides for a composition comprising an inorganic scintillator comprising an alkali metal hafnate, optionally cerium-doped, having the formula A2HfO3:Ce; wherein A is an alkali metal having a valence of 1, such as Li or Na; and the molar percent of cerium is 0% to 100%. The alkali metal hafnate are scintillators and produce a bright luminescence upon irradiation by a suitable radiation.

High-pressure torsion of hafnium

International Nuclear Information System (INIS)

Edalati, Kaveh; Horita, Zenji; Mine, Yoji

2010-01-01

Pure Hf (99.99%) is processed by high-pressure torsion (HPT) under pressures of 4 and 30 GPa to form an ultrafine-grained structure with a gain size of ∼180 nm. X-ray diffraction analysis shows that, unlike Ti and Zr, no ω phase formation is detected after HPT processing even under a pressure of 30 GPa. A hydride formation is detected after straining at the pressure of 4 GPa. The hydride phase decomposes either by application of a higher pressure as 30 GPa or by unloading for prolong time after HPT processing. Microhardness, tensile and bending tests show that a high hardness (360 Hv) and an appreciable ductility (8%) as well as high tensile and bending strength (1.15 and 2.75 GPa, respectively) are achieved following the high-pressure torsion.

X-ray target with substrate of molybdenum alloy

International Nuclear Information System (INIS)

Hirsch, H.H.

1980-01-01

Rotary targets for x-ray tubes are provided comprising a molybdenum base body alloyed with a stabilizing proportion of iron, silicon, cobalt, tantalum, niobium, hafnium, stable metal oxide, or a mixture of the preceding

Control rod

International Nuclear Information System (INIS)

Igarashi, Takao; Sugawara, Satoshi; Yoshimoto, Yuichiro; Saito, Shozo; Fukumoto, Takashi.

1987-01-01

Purpose: To reduce the weight and thereby obtain satisfactory operationability of control rods by combining absorbing nuclear chain type neutron absorbers and conventional type neutron absorbers in the axial direction of blades. Constitution: Neutron absorber rods and long life type neutron absorber rods are disposed in a tie rod and a sheath. The neutron absorber rod comprises a poison tube made of stainless steels and packed with B 4 C powder. The long life type neutron absorber rod is prepared by packing B-10 enriched boron carbide powder into a hafnium metal rod, hafnium pipe, europium and stainless made poison tube. Since the long life type absorber rod uses HF as the absorbing nuclear chain type neutron absorber, it absorbs neutrons to form new neutron absorbers to increase the nuclear life. (Yoshino, Y.)

Thermodynamic study of the MWG system/components and measurement of the oxygen partial pressure in the heat source capsule

International Nuclear Information System (INIS)

David, D.J.

1980-01-01

A thermodynamic study of the Milliwatt Generator heat source capsule was performed to determine the effects of the oxide fuel on container materials at elevated temperatures in order to evaluate the factors affecting embrittlement of T-111 alloy. The study indicates that relatively slow oxidation of the T-111 of the capsule occurs during pretreatment. Yttrium added to the 238 PuO 2 fuel charge is functioning in its designed role as an oxygen getter and is stabilizing at an O/Pu ratio of 1.75. The free energy of formation of hafnium oxide has been measured and found to be -70632 cal/mole; this suggests that the ability of hafnium to strongly function as an oxygen getter may be largely determined by the kinetics, and the free energy may play a lesser role

Development of Advanced Environmental Barrier Coatings for SiC/SiC Ceramic Matrix Composites: Path Toward 2700 F Temperature Capability and Beyond

Science.gov (United States)

Zhu, Dongming; Harder, Bryan; Hurst, Janet B.; Good, Brian; Costa, Gustavo; Bhatt, Ramakrishna T.; Fox, Dennis S.

2017-01-01

Advanced environmental barrier coating systems for SiC-SiC Ceramic Matrix Composite (CMC) turbine and combustor hot section components are currently being developed to meet future turbine engine emission and performance goals. One of the significant coating development challenges is to achieve prime-reliant environmental barrier coating systems to meet the future 2700F EBC-CMC temperature stability and environmental durability requirements. This presentation will emphasize recent NASA environmental barrier coating system testing and down-selects, particularly the development path and properties towards 2700-3000F durability goals by using NASA hafnium-hafnia-rare earth-silicon-silicate composition EBC systems for the SiC-SiC CMC turbine component applications. Advanced hafnium-based compositions for enabling next generation EBC and CMCs capabilities towards ultra-high temperature ceramic coating systems will also be briefly mentioned.

10 CFR Appendix L to Part 110 - Illustrative List of Byproduct Materials Under NRC Export/Import Licensing Authority a

Science.gov (United States)

2010-01-01

... material produced, extracted, or converted for use for a commercial, medical, or research activity...) Gallium 72 (Ga 72) Germanium 68 (Ge 68) Germanium 71 (Ge 71) Gold 198 (Au 198) Gold 199 (Au 199) Hafnium...

Nutritional determinants of worldwide diabetes: an econometric study of food markets and diabetes prevalence in 173 countries.

Science.gov (United States)

Basu, Sanjay; Stuckler, David; McKee, Martin; Galea, Gauden

2013-01-01

Ageing and urbanization leading to sedentary lifestyles have been the major explanations proposed for a dramatic rise in diabetes worldwide and have been the variables used to predict future diabetes rates. However, a transition to Western diets has been suggested as an alternative driver. We sought to determine what socio-economic and dietary factors are the most significant population-level contributors to diabetes prevalence rates internationally. Multivariate regression models were used to study how market sizes of major food products (sugars, cereals, vegetable oils, meats, total joules) corresponded to diabetes prevalence, incorporating lagged and cumulative effects. The underlying social determinants of food market sizes and diabetes prevalence rates were also studied, including ageing, income, urbanization, overweight prevalence and imports of foodstuffs. Data were obtained from 173 countries. Population-based survey recipients were the basis for diabetes prevalence and food market data. We found that increased income tends to increase overall food market size among low- and middle-income countries, but the level of food importation significantly shifts the content of markets such that a greater proportion of available joules is composed of sugar and related sweeteners. Sugar exposure statistically explained why urbanization and income have been correlated with diabetes rates. Current diabetes projection methods may estimate future diabetes rates poorly if they fail to incorporate the impact of nutritional factors. Imported sugars deserve further investigation as a potential population-level driver of global diabetes.

Hafnium and neodymium isotopes and REY distribution in the truly dissolved, nanoparticulate/colloidal and suspended loads of rivers in the Amazon Basin, Brazil

Science.gov (United States)

Merschel, Gila; Bau, Michael; Schmidt, Katja; Münker, Carsten; Dantas, Elton L.

2017-09-01

Radiogenic isotopes in river sediments and river waters have been widely used in provenance studies, as these samples naturally integrate the geology/chemistry of the entire catchment. While the Hf and Nd isotope systems are coupled during igneous processes, they are decoupled during supergene processes at the Earth's surface, which is reflected by the isotope composition of riverine sediments. We present the first data for both Hf and Nd isotope compositions of the dissolved (0.2 μm-filtrates rich in nanoparticles and colloids, NPCs) and the truly dissolved (1 kDa-ultrafiltrates) load of rivers. Hafnium and Nd isotope compositions and concentrations of the Rare Earths and Yttrium (REY) and Hf were determined for suspended particles (>0.2 μm) as well as for the dissolved and the truly dissolved load of the Rio Solimões, the Amazon's largest tributary draining the Andes, and of the Rio Negro, an organic NPC- and particle-rich river draining the rainforest of northern Amazonia. We also analyzed the Nd isotope compositions of suspended sediments and 0.2 μm-filtered water samples from the Amazon River and its tributaries Rio Tapajos, Rio Xingu and Rio Jari. Our novel results clearly show that the decoupling of the Hf and Nd isotope systems is related to incongruent weathering processes on the continent, as this decoupling can already be observed in the different Hf and Nd pools, i.e. in the particulate, the NPC-dominated dissolved and the truly dissolved load of rivers. In the Rio Negro and Rio Solimões, a strong particle size-dependent difference in Hf isotope composition is observed. Values of εHf become more radiogenic as filter poresize decreases, which can be related to the density- and size-dependent distribution of Hf-rich minerals, e.g. zircons, and their absence from the truly dissolved pool. In contrast, the Nd isotope composition of Amazonian river waters reflects that of their catchment geology. Tributaries draining the Precambrian Brazilian and

Fabrication of cermet bearings for the control system of a high temperature lithium cooled nuclear reactor

Science.gov (United States)

Yacobucci, H. G.; Heestand, R. L.; Kizer, D. E.

1973-01-01

The techniques used to fabricate cermet bearings for the fueled control drums of a liquid metal cooled reference-design reactor concept are presented. The bearings were designed for operation in lithium for as long as 5 years at temperatures to 1205 C. Two sets of bearings were fabricated from a hafnium carbide - 8-wt. % molybdenum - 2-wt. % niobium carbide cermet, and two sets were fabricated from a hafnium nitride - 10-wt. % tungsten cermet. Procedures were developed for synthesizing the material in high purity inert-atmosphere glove boxes to minimize oxygen content in order to enhance corrosion resistance. Techniques were developed for pressing cylindrical billets to conserve materials and to reduce machining requirements. Finishing was accomplished by a combination of diamond grinding, electrodischarge machining, and diamond lapping. Samples were characterized in respect to composition, impurity level, lattice parameter, microstructure and density.

The determination of light elements in heavy matrix using proton induced X-ray emission

International Nuclear Information System (INIS)

Levenets, V.V.; Omel'nik, A.P.; Shchur, A.A.; Chernov, A.E.; Usikov, N.P.; Zats, A.V.

2007-01-01

In this report the possibility of determination of light impurities in heavy matrixes is studied using proton induced X-Ray emission. The wide-band X-ray emission filter made from pyrolytic graphite was used in spectrometric scheme of experiment. The results of studying of filter features in energy range of X-ray emission from 4 to 12 keV were presented. The possibilities were examined of application of pyrolytic graphite filter to modify the X-rays spectrum for determination of iron, using characteristic emission of K-series, and hafnium, using L-series, in substances on base of zirconium (glasses, alloys etc.). It was shown, that the using of similar filter allows to reach the significant improving of metrological characteristics of analysis of mentioned impurities: the limits of detection of iron and hafnium were lowered single-order of magnitude. (authors)

Evaluation of the performance of national health systems in 2004-2011: An analysis of 173 countries.

Science.gov (United States)

Sun, Daxin; Ahn, Haksoon; Lievens, Tomas; Zeng, Wu

2017-01-01

In an effort to improve health service delivery and achieve better health outcomes, the World Health Organization (WHO) has called for improved efficiency of health care systems to better use the available funding. This study aims to examine the efficiency of national health systems using longitudinal country-level data. Data on health spending per capita, infant mortality rate (IMR), under 5 mortality rate (U5MR), and life expectancy (LE) were collected from or imputed for 173 countries from 2004 through 2011. Data envelopment analyses were used to evaluate the efficiency and regression models were constructed to examine the determinants of efficiency. The average efficiency of the national health system, when examined yearly, was 78.9%, indicating a potential saving of 21.1% of health spending per capita to achieve the same level of health status for children and the entire population, if all countries performed as well as their peers. Additionally, the efficiency of the national health system varied widely among countries. On average, Africa had the lowest efficiency of 67%, while West Pacific countries had the highest efficiency of 86%. National economic status, HIV/AIDS prevalence, health financing mechanisms and governance were found to be statistically associated with the efficiency of national health systems. Taking health financing as an example, a 1% point increase of social security expenses as a percentage of total health expenditure correlated to a 1.9% increase in national health system efficiency. The study underscores the need to enhance efficiency of national health systems to meet population health needs, and highlights the importance of health financing and governance in improving the efficiency of health systems, to ultimately improve health outcomes.

Energy dependence of kaon-to-proton ratio fluctuations in central Pb+Pb collisions from $\\sqrt{s_{NN}}$ = 6.3 to 17.3 GeV

CERN Document Server

Anticic, T.; Barna, D.; Bartke, J.; Beck, H.; Betev, L.; Bialkowska, H.; Blume, C.; Bogusz, M.; Boimska, B.; Book, J.; Botje, M.; Buncic, P.; Cetner, T.; Christakoglou, P.; Chung, P.; Chvala, O.; Cramer, J.G.; Eckardt, V.; Fodor, Z.; Foka, P.; Friese, V.; Gazdzicki, M.; Grebieszkow, K.; Hohne, C.; Kadija, K.; Karev, A.; Kolesnikov, V.I.; Kollegger, T.; Kowalski, M.; Kresan, D.; Laszlo, A.; Lacey, R.; van Leeuwen, M.; Mackowiak, M.; Makariev, M.; Malakhov, A.I.; Mateev, M.; Melkumov, G.L.; Mitrovski, M.; Mrowczynski, St.; Nicolic, V.; Palla, G.; Panagiotou, A.D.; Peryt, W.; Pluta, J.; Prindle, D.; Puhlhofer, F.; Renfordt, R.; Roland, C.; Roland, G.; Rybczynski, M.; Rybicki, A.; Sandoval, A.; Schmitz, N.; Schuster, T.; Seyboth, P.; Sikler, F.; Skrzypczak, E.; Slodkowski, M.; Stefanek, G.; Stock, R.; Strobele, H.; Susa, T.; Szuba, M.; Utvic, M.; Varga, D.; Vassiliou, M.; Veres, G.I.; Vesztergombi, G.; Vranic, D.; Wlodarczyk, Z.; Wojtaszek-Szwarc, A.

2011-01-01

Kaons and protons carry large parts of two conserved quantities, strangeness and baryon number. It is argued that their correlation and thus also fluctuations are sensitive to conditions prevailing at the anticipated parton-hadron phase boundary. Fluctuations of the $(\\mathrm{K}^+ + \\mathrm{K}^-)/(\\mathrm{p}+\\bar{\\mathrm{p}})$ and $\\mathrm{K}^+/\\mathrm{p}$ ratios have been measured for the first time by NA49 in central Pb+Pb collisions at 5 SPS energies between $\\sqrt{s_{NN}}$= 6.3~GeV and 17.3~GeV. Both ratios exhibit a change of sign in $\\sigma_{\\mathrm{dyn}}$, a measure of non-statistical fluctuations, around $\\sqrt{s_{NN}}$ = 8~GeV. Below this energy, $\\sigma_{\\mathrm{dyn}}$ is positive, indicating higher fluctuation compared to a mixed event background sample, while for higher energies, $\\sigma_{\\mathrm{dyn}}$ is negative, indicating correlated emission of kaons and protons. The results are compared to UrQMD calculations which which give a good description at the higher SPS energies, but fail to reproduc...

Chemical effects in x-ray emission spectra

International Nuclear Information System (INIS)

Fernandes, N.G.

1982-01-01

The chemical bond influence in X-ray emission spectra of hafnium, iodine, iron, sulphur, aluminium and magnesium is detected. The position of one X-ray emission line is determined by three methods: parabolic profile; Gaussian distribution and extra-heavy maximum. (author)

Highly stable thin film transistors using multilayer channel structure

KAUST Repository

Nayak, Pradipta K.; Wang, Zhenwei; Anjum, Dalaver H.; Hedhili, Mohamed N.; Alshareef, Husam N.

2015-01-01

We report highly stable gate-bias stress performance of thin film transistors (TFTs) using zinc oxide (ZnO)/hafnium oxide (HfO2) multilayer structure as the channel layer. Positive and negative gate-bias stress stability of the TFTs was measured

EXPERIMENTAL ANALYSIS OF THE HEALING PROCESS IN THE AREA OF TIBIAL BONE FRACTURE

Directory of Open Access Journals (Sweden)

I. F. Аkhtyamov

2016-01-01

Full Text Available Purpose. To quantify the density of the cortical bone of the tibia in the area of reparative regeneration and the state of the vascular bed (hemodynamics of the operated limb under intramedullary osteosynthesis using pins coated with titanium and hafnium nitrides. Materials and methods. In the experiment, changes in the bone density and the characteristics of the local blood supply were studied on 40 outbred rabbits which underwent intramedullary osteosynthesis by the use of pins with a nanocoating based on superhard compounds which consist of titanium and hafnium nitrides and pins without a coating. Using color Doppler mode helped to evaluate the condition of the vascular bed proximally to the fracture site. Results. It is noted that the use of pins with the described coating above did not violate the osteoregeneration staging. The density of the cortical bone in the test group exceeded that of the comparison group by an average of 30%. Bone remodeling processes in the test group completed at an earlier date, as determined by the higher rates of its density. In the study of the vascular bed of the operated limb, it was found that on the 10th day of the experiment, an increase in the maximal velocity of the blood flow was recorded (TAMAX. In animals of the test group this index approached preoperative values on the 30th day, while in animals of the comparison group this index approached the initial values only by the 60th day. Conclusion. The use of implants coated with titanium and hafnium nitrides which are characterized by high strength, thermal and chemical stability is accompanied by the formation of a cortical bone in the area of osteotomy with higher density characteristics. The changes which are typical of the vasodilatation in the area of injury in the early postoperative period can be regarded as a positive factor in the formation of primary bone union. In the group where implants coated with titanium and hafnium nitrides were used

Behavior of uranium and its surrogates in molten aluminosilicate glasses in contact with liquid metals

International Nuclear Information System (INIS)

Chevreux, Pierrick

2016-01-01

This study concerns an innovative process used for conditioning nuclear waste that contain metallic parts contaminated with actinides. High actinides concentrations are expected to be incorporated in the glass melt in contact with the molten metals. Among these metals, aluminum and/or stainless steel impose a strongly reducing environment to the glass melt involving redox reactions. These reactions modify actinides oxidation states and therefore change their solubilities in the glass and could also reduce them into the metallic form. In this work, we focus on the behavior of uranium and its surrogates, namely hafnium and neodymium, in aluminosilicate glasses from the Na 2 O-CaO-SiO 2 -Al 2 O 3 system melted in highly reducing conditions. The first step consists in comparing the hafnium and uranium solubilities in the glass as functions of redox conditions and glass composition. A methodology has been set up and a specific device has been used to control the oxygen fugacity and the alkali content of the glass. The results show that uranium is far less soluble in the glass than hafnium (Hf(IV)) in reducing conditions. The uranium solubility ranges from 4 to 7 wt% UO 2 for an oxygen fugacity below 10 -14 atm at 1250 C-1400 C. Uranium oxidation states have been investigated by X-ray absorption spectroscopy (XANES). It has been pointed out that U(IV) is the main form in the glass for such imposed oxygen fugacities. The second step of this work is to identify the glass-metal interaction mechanisms in order to determine the localization of uranium and its surrogates (Nd, Hf) in the glass-metal system. Mechanisms are mostly ruled by the presence of metallic aluminum and are similar for uranium, neodymium and hafnium. Glass-metal interaction kinetics demonstrate that uranium and its surrogates can temporarily be reduced into the metallic form for particular conditions. A re-oxidation occurs with time which is in good agreement with thermodynamics. Regarding uranium, the re

A Fully Transparent Resistive Memory for Harsh Environments

KAUST Repository

Yang, Po-Kang; Ho, Chih-Hsiang; Lien, Der-Hsien; Duran Retamal, Jose Ramon; Kang, Chen-Fang; Chen, Kuan-Ming; Huang, Teng-Han; Yu, Yueh-Chung; Wu, Chih-I; He, Jr-Hau

2015-01-01

A fully transparent resistive memory (TRRAM) based on Hafnium oxide (HfO2) with excellent transparency, resistive switching capability, and environmental stability is demonstrated. The retention time measured at 85 °C is over 3 × 104 sec

173 | Page

African Journals Online (AJOL)

Fr. Ikenga

Again, individuals and non-governmental organization (NGO's) suffer great restraint in .... by individuals or non-governmental organizations (NGOs) with observer status before the African. Commission on Human and ..... Innovations and Prospect of the African Court on Human and Peoples' Rights. In furtherance of effective ...

Influences of different oxidants on the characteristics of HfAlOx films deposited by atomic layer deposition

International Nuclear Information System (INIS)

Fan Ji-Bin; Liu Hong-Xia; Ma Fei; Zhuo Qing-Qing; Hao Yue

2013-01-01

A comparative study of two kinds of oxidants (H 2 O and O 3 ) with the combinations of two metal precursors [trimethylaluminum (TMA) and tetrakis(ethylmethylamino) hafnium (TEMAH)] for atomic layer deposition (ALD) hafnium aluminum oxide (HfAlO x ) films is carried out. The effects of different oxidants on the physical properties and electrical characteristics of HfAlO x films are studied. The preliminary testing results indicate that the impurity level of HfAlO x films grown with both H 2 O and O 3 used as oxidants can be well controlled, which has significant effects on the dielectric constant, valence band, electrical properties, and stability of HfAlO x film. Additional thermal annealing effects on the properties of HfAlO x films grown with different oxidants are also investigated. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Low-temperature fabrication of an HfO2 passivation layer for amorphous indium-gallium-zinc oxide thin film transistors using a solution process.

Science.gov (United States)

Hong, Seonghwan; Park, Sung Pyo; Kim, Yeong-Gyu; Kang, Byung Ha; Na, Jae Won; Kim, Hyun Jae

2017-11-24

We report low-temperature solution processing of hafnium oxide (HfO 2 ) passivation layers for amorphous indium-gallium-zinc oxide (a-IGZO) thin-film transistors (TFTs). At 150 °C, the hafnium chloride (HfCl 4 ) precursor readily hydrolyzed in deionized (DI) water and transformed into an HfO 2 film. The fabricated HfO 2 passivation layer prevented any interaction between the back surface of an a-IGZO TFT and ambient gas. Moreover, diffused Hf 4+ in the back-channel layer of the a-IGZO TFT reduced the oxygen vacancy, which is the origin of the electrical instability in a-IGZO TFTs. Consequently, the a-IGZO TFT with the HfO 2 passivation layer exhibited improved stability, showing a decrease in the threshold voltage shift from 4.83 to 1.68 V under a positive bias stress test conducted over 10,000 s.

Thermodynamics of HfCl/sub 4/-KCl molten mixtures containing HfCl/sub 4/ up to 33. 3 mol. per cent

Energy Technology Data Exchange (ETDEWEB)

Smirnov, M V; Salyulev, A B; Kudyakov, V Ya [AN SSSR, Sverdlovsk. Inst. Ehlektrokhimii

1980-05-01

Based on measurements of saturated vapour pressure in components of melted mixtures of HfCl/sub 4/-KCl, depending on temperature and concentration, calculated are the results of changes in activity coefficients of hafnium tetrachloride and potassium chloride on transition from diluted solutions, where the Henry law is met, to those concentrated where the law is disobeyed. Growth in the activity coefficient of HfCl/sub 4/ is due to dissociation of complex groups of HfCl/sub 6//sup 2 -/ into complexes with a lesser number of ligands and decreasing relative binding energy of Hf/sup 4 +/-Cl/sup -/ there. In this case, marked changes take place in partial enthalpy and entropy of hafnium tetrachloride mixing. Similar dependences are observed for potassium chloride, but they are expressed considerably weaker. Evaporation enthalpy and entropy are calculated for HfCl/sub 4/ and KCl monomers from their melted mixtures of various concentrations.

Thermodynamics of HfCl4-KCl molten mixtures containing HfCl4 up to 33.3 mol. per cent

International Nuclear Information System (INIS)

Smirnov, M.V.; Salyulev, A.B.; Kudyakov, V.Ya.

1980-01-01

Based on measurements of saturated vapour pressure in components of melted mixtures of HfCl 4 -KCl, depending on temperature and concentration, calculated are the results of changes in activity coefficients of hafnium tetrachloride and potassium chloride on transition from diluted solutions, where the Henry law is met, to those concentrated where the law is disobeyed. Growth in the activity coefficient of HfCl 4 is due to dissociation of complex groups of HfCl 6 2- into complexes with a lesser number of ligands and decreasing relative binding energy of Hf 4+ -Cl - there. In this case, marked changes take place in partial enthalpy and entropy of hafnium tetrachloride mixing. Similar dependences are observed for potassium chloride, but they are expressed considerably weaker. Evaporation enthalpy and entropy are calculated for HfCl 4 and KCl monomers from their melted mixtures of various concentrations

The high-spin {sup 178m2}Hf isomer: production, chemical and isotopic separations, gamma spectrometry and internal conversion electrons spectrometry; L`isomere de haut spin {sup 178m2}Hf: production, separations chimiques et isotopiques, spectrometrie gamma et spectrometrie d`electrons de conversion interne

Energy Technology Data Exchange (ETDEWEB)

Kim, J B

1993-10-13

The high-spin isometric state of the nucleus 178Hf is a challenge for new and exotic nuclear physics studies. With its long half-life of 31 years, the production of a reasonable micro-weight quantity, with an isometric to ground state ratio as high as 5 per cent, is now regularly performed by intensive irradiations of ytterbium targets with helium ions of 36 MeV. Using sur-enriched, at 99,998 per cent, ytterbium 176 that we have prepared at the PARIS mass separator, the isomer purity has been improved. Targets of such material but also of enriched stable isotopes of hafnium have been prepared by electro-spraying of methanolic and acetic solutions. By inelastic diffusion of protons and deuton on these targets, the energy of the first state of the rotation band built on the isomer has been measured. Isotopic separations of the isomer have been performed, with a yield greater than 20 per cent, by the use of isotopically pure hafnium 176 as carrier. The separated beam of the mass 178 allowed to record the complete hyperfine spectrum of the isomer and to measure, for the first time, the magnetic dipole moment and the electric quadrupole moment. Isomer targets, implanted in various materials like copper, iron and hafnium monocrystal, provide the opportunity to accurately measure gamma and internal conversion decay of this nuclei and so to precise the multipolarity mixing of all transitions from K=16{sup +} to K=8{sup -}. (author). 49 refs., 47 figs., 11 tabs.

m manjula

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science. M MANJULA. Articles written in Bulletin of Materials Science. Volume 41 Issue 1 February 2018 pp 19. Elastic and thermodynamic properties of zirconium- and hafnium-doped Rh$_3$V intermetallic compounds: potential aerospace material · M MANJULA M SUNDARESWARI ...

Structure of Zr-Hf alloys

International Nuclear Information System (INIS)

Dobromyslov, A.V.; Taluts, N.I.

1991-01-01

Structure of quenched zirconium-hafnium alloy system containing up to 2.5 at. % was studied. Existence of three morphological forms of α-phase was presented: lath, twinned, laminated. Twinning plane in the system was identified. Formation model of packet structure of lath martensite was suggested

New candidates for active asteroids: Main-belt (145) Adeona, (704) Interamnia, (779) Nina, (1474) Beira, and near-Earth (162,173) Ryugu

Science.gov (United States)

Busarev, Vladimir V.; Makalkin, Andrei B.; Vilas, Faith; Barabanov, Sergey I.; Scherbina, Marina P.

2018-04-01

For the first time, spectral signs of subtle coma activity were observed for four main-belt primitive asteroids (145) Adeona, (704) Interamnia, (779) Nina, and (1474) Beira around their perihelion distances in September 2012, which were interpreted as manifestations of the sublimation of H2O ice in/under the surface matter (Busarev et al., 2015a, 2015b). We confirm the phenomenon for Nina when it approached perihelion in September 2016. At the same time, based on results of spectral observations of near-Earth asteroid (162,173) Ryugu (Vilas, 2008) being a target of Japan's Hayabusa 2 space mission, we suspected a periodic similar transient activity on the Cg-type asteroid. However, unlike the main-belt primitive asteroids demonstrating sublimation of ices close to their perihelion distances, the effect on Ryugu was apparently registered near aphelion. To explain the difference, we calculated the subsolar temperature depending on heliocentric distance of the asteroids, considered qualitative models of internal structure of main-belt and near-Earth primitive asteroids including ice and performed some analytical estimations. Presumed temporal sublimation/degassing activity of Ryugu is a sign of a residual frozen core in its interior. This could be an indication of a relatively recent transition of the asteroid from the main asteroid belt to the near-Earth area.

Nanomechanical properties of hafnium nitride coating

International Nuclear Information System (INIS)

Chen Yao; Laha, Tapas; Balani, Kantesh; Agarwal, Arvind

2008-01-01

Nanomechanical properties of plasma-sprayed HfN coating with and without hot isostatic pressing (HIP) treatment were evaluated using nanoindentation. For HIPed HfN coating, the elastic modulus (E) and yield strength increase whereas the hardness (H), H/E ratio and fraction of the elastic work decrease. HIPed HfN coating shows a larger pile-up around the indent as compared to as-sprayed HfN. HIPing causes densification and improvement in inter-splat bonding which subsequently lead to increase in nanomechanical properties

Coexistence of different charge states in Ta-doped monoclinic HfO2: Theoretical and experimental approaches

DEFF Research Database (Denmark)

Taylor, M.A.; Alonso, R.E.; Errico, L.A.

2010-01-01

A combination of experiments and ab initio quantum-mechanical calculations has been applied to examine hyperfine interactions in Ta-doped hafnium dioxide. Although the properties of monoclinic HfO2 have been the subject of several earlier studies, some aspects remain open. In particular, time dif...

Temperature Effects on a-IGZO Thin Film Transistors Using HfO2 Gate Dielectric Material

Directory of Open Access Journals (Sweden)

Yu-Hsien Lin

2014-01-01

Full Text Available This study investigated the temperature effect on amorphous indium gallium zinc oxide (a-IGZO thin film transistors (TFTs using hafnium oxide (HfO2 gate dielectric material. HfO2 is an attractive candidate as a high-κ dielectric material for gate oxide because it has great potential to exhibit superior electrical properties with a high drive current. In the process of integrating the gate dielectric and IGZO thin film, postannealing treatment is an essential process for completing the chemical reaction of the IGZO thin film and enhancing the gate oxide quality to adjust the electrical characteristics of the TFTs. However, the hafnium atom diffused the IGZO thin film, causing interface roughness because of the stability of the HfO2 dielectric thin film during high-temperature annealing. In this study, the annealing temperature was optimized at 200°C for a HfO2 gate dielectric TFT exhibiting high mobility, a high ION/IOFF ratio, low IOFF current, and excellent subthreshold swing (SS.

Pressure induced phase transition in HfTiO4

International Nuclear Information System (INIS)

Mishra, A.K.; Garg, Nandini; Sharma, Surinder M.; Panneerselvam, G.

2012-01-01

Hafnium titanate is a low thermal expansion ceramic with a very good absorption cross section for thermal neutrons and a high refractoriness, thus making it a desirable nuclear material. At ambient conditions it crystallizes with the orthorhombic structure (space group Pbcn). The material properties of this ceramic have been studied as a function of temperature. However, apart from a lone shock study several decades ago there is no study at static high pressure on this compound. Since this ceramic is used as control rods in nuclear reactors it is important to understand its phase stability at different thermodynamic conditions. Therefore to understand the high pressure behaviour of hafnium titanate we have carried out diamond anvil cell based X-ray diffraction studies up to ∼20 GPa. The studies on this ceramic show that its structure is stable till 11 GPa. However, at ∼11.7 GPa appearance of new diffraction peaks indicate that it undergoes a structural phase transition to a low symmetry structure

Mesocrystals luminescent BaZrHfO{sub 3} synthesized via hydrothermal process assisted by microwave

Energy Technology Data Exchange (ETDEWEB)

Fassbender, Rafael Uarth, E-mail: uarth.fisica@gmail.com

2016-07-01

Full text: The Barium Zirconate (BaZrO{sub 3}), is a ceramic oxide belonging to the functional group of perovskites (ABO{sub 3}), this compound can be doped with hafniun (Hf) in solid solution by microwave assisted hydrothermal method (MAH) radioluminescent increases their properties. This method allows to obtain barium zirconate at low temperature as 140 deg C and short times as 160 minutes. The choice of Hafnium (Hf) as a dopant is based on its similarity with Zirconium (Zr), another good reason for this choice is that the Hafnium has intrinsic luminescent characteristics. In general, radioluminescent materials have high density and high atomic mass (atomic number of Hafnium is 72), thereby facilitating the absorption of ionizing radiation to convert it into visible light, this characteristic is strongly dependent on the morphology and especially the electronic structure of (BaZrO{sub 3}). This work consisted in production of barium zirconate powders doped 1-2-4-8-16% (Hf) using (MAH) method. For the characterization of the powders was employed methods : a) X-ray diffraction, b) Raman Spectroscopy, c) Xanes, d) photoluminescence spectroscopy. After the electronic and structural characterization the powders were introduced in a polymeric resin (nylon-BZO), one new characterizations will be performed to validate the results obtained in the production of films to the results already obtained for the powders. We conclude so far, that the powders-doped with 16% Hf has an intense luminescent emission compared to the powders with less concentration of Hf. The small structural change that causes the Hf in (BZO) is considered as a secondary factory. (author)

Catalytic activity of metall-like carbides in carbon oxide oxidation reaction

International Nuclear Information System (INIS)

Kharlamov, A.I.; Kosolapova, T.Ya.; Rafal, A.N.; Kirillova, N.V.

1980-01-01

Kinetics of carbon oxide oxidation upon carbides of hafnium, niobium, tantalum, molybdenum, zirconium and chromium is studied. Probable mechanism of the catalysts action is suggested. The established character of the change of the carbide catalytic activity is explained by the change of d-electron contribution to the metal-metal interaction

George de Hevesy (1885 - 1966), founder of radioanalytical chemistry

International Nuclear Information System (INIS)

Niese, S.

2006-01-01

George de Hevesy has founded Radioanalytical Chemistry and Nuclear Medicine, discovered the element hafnium and first separated stable isotopes. For all these different important achievements he was nominated for the Nobel Prize. On occasion of his discovery of activation analysis 70 years ago his life and work will be illustrated. (author)

Pramana – Journal of Physics | Indian Academy of Sciences

Indian Academy of Sciences (India)

Home; Journals; Pramana – Journal of Physics; Volume 68; Issue 1 ... pp 1-19 Research Articles ... Maximum yield and best quality CNTs were obtained using H2 as the carrier gas. ... Electronic structure of hafnium: A Compton profile study ... Odd–even effect in fragment angular momentum in low-energy fission of actinides.

Nanomechanical study of amorphous and polycrystalline ALD HfO2 thin films

Science.gov (United States)

K. Tapily; J.E. Jakes; D. Gu; H. Baumgart; A.A. Elmustafa

2011-01-01

Thin films of hafnium oxide (HfO2) were deposited by atomic layer deposition (ALD). The structural properties of the deposited films were characterised by transmission electron microscopy (TEM) and X-ray diffraction (XRD). We investigated the effect of phase transformations induced by thermal treatments on the mechanical properties of ALD HfO

Neutron activation analysis measurements of sub micron aerosol deposition onto a cylinder energized with an alternating electric field

Energy Technology Data Exchange (ETDEWEB)

Fila, M S [Toronto Univ., ON (Canada). Dept. of Chemical Engineering and Applied Chemistry

1994-12-31

Experimental measurements of aerosol deposition onto a cylinder energized with a 60 Hz electric field were conducted using a neutron activation analysis technique with a hafnium salt aerosol. The measured collection efficiencies were compared to theoretical expressions based on an electrostatic collection mechanism and fair agreement was found. (author). 5 refs., 1 tab., 2 figs.

Viscosity measurements of molten refractory metals using an electrostatic levitator

International Nuclear Information System (INIS)

Ishikawa, Takehiko; Paradis, Paul-François; Okada, Junpei T; Watanabe, Yuki

2012-01-01

Viscosities of several refractory metals (titanium, nickel, zirconium, niobium, ruthenium, rhodium, hafnium, iridium and platinum) and terbium have been measured by the oscillation drop method with an improved procedure. The measured data were less scattered than our previous measurements. Viscosities at their melting temperatures showed good agreement with literature values and some predicted values. (paper)

Submicrometric gratings fabrication from photosensitive organo-silica-hafnia thin films elaborated by sol-gel processing

Energy Technology Data Exchange (ETDEWEB)

Franc, Janyce [Universite de Lyon, F-42023 Saint-Etienne (France); CNRS, UMR 5516, Laboratoire Hubert Curien, 42023 Saint-Etienne (France); Universite de Saint-Etienne, Jean-Monnet, F-42023 Saint-Etienne (France); Barnier, Vincent, E-mail: barnier@emse.fr [Ecole Nationale Superieure des Mines, SMS-EMSE, CNRS:UMR 5146, LCG, F-42023 Saint-Etienne (France); Vocanson, Francis, E-mail: francis.vocanson@univ-st-etienne.fr [Universite de Lyon, F-42023 Saint-Etienne (France); CNRS, UMR 5516, Laboratoire Hubert Curien, 42023 Saint-Etienne (France); Universite de Saint-Etienne, Jean-Monnet, F-42023 Saint-Etienne (France); Gamet, Emilie; Lesage, Maryline [Universite de Lyon, F-42023 Saint-Etienne (France); CNRS, UMR 5516, Laboratoire Hubert Curien, 42023 Saint-Etienne (France); Universite de Saint-Etienne, Jean-Monnet, F-42023 Saint-Etienne (France); Jamon, Damien [Universite de Lyon, F-42023 Saint-Etienne (France); Laboratoire Claude Chappe, Telecom Saint-Etienne, 42000 Saint-Etienne Cedex 2 (France); Universite de Saint-Etienne, Jean-Monnet, F-42023 Saint-Etienne (France); Jourlin, Yves [Universite de Lyon, F-42023 Saint-Etienne (France); CNRS, UMR 5516, Laboratoire Hubert Curien, 42023 Saint-Etienne (France); Universite de Saint-Etienne, Jean-Monnet, F-42023 Saint-Etienne (France)

2012-07-31

The aim of this study is the elaboration of a high index sol-gel material in order to prepare submicrometric grating. The gratings were obtained after few seconds of UV exposure in one step using an organically modified silica-hafnia matrix. The chemical composition of thin films after UV and annealing treatments were studied using Fourier Transform Infrared Spectroscopy and X-Ray Photoelectron Spectroscopy. The study of optical properties revealed that the annealed films are transparent from 200 to 1000 nm and have a refractive index from 1.550 to 1.701 depending on the hafnium concentration. - Highlights: Black-Right-Pointing-Pointer Silica-hafnia matrix with high refractive index was prepared using sol-gel process. Black-Right-Pointing-Pointer Organic and inorganic networks formation of thin films was investigated. Black-Right-Pointing-Pointer Optical properties are influenced by annealing treatment and initial hafnium amount. Black-Right-Pointing-Pointer The use of high Si:Hf molar ratio can lead to a loss transmittance below 300 nm. Black-Right-Pointing-Pointer Submicrometric grating period can be prepared using a holographic method.

Dissolution kinetics of small amounts of oxygen in tantalum alloy T-111 and internal oxide displacement reactions during annealing

Science.gov (United States)

Stecura, S.

1976-01-01

Oxygen was added to T-111 (Ta-8W-2Hf, wt. %) at 820 and 990 C at an oxygen pressure of about 0.0003 torr. The technique employed permitted predetermined and reproducible doping of T-111 up to 3.0 at. % oxygen. Based on the temperature dependence of the doping reaction, it is concluded that the initial rates of oxygen pickup are probably controlled by solution of oxygen into the T-111 lattice. Although hafnium oxides are more stable than those of tantalum or tungsten, analyses of extracted residues indicate that the latter oxides predominate in the as-doped specimens, presumably because of the higher concentrations of tantalum and tungsten in the alloy. However, high-temperature annealing promotes gettering of dissolved oxygen and of other oxides to form hafnium oxides. Small amounts of tantalum and tungsten oxides were still present after high-temperature annealing. Tungsten oxide (WO3) volatilizes slightly from the surface of T-111 at 990 C. The vaporization of WO3 has no apparent affect on the doping reaction.

Temperature dependence of the work function of ruthenium-based gate electrodes

International Nuclear Information System (INIS)

Alshareef, H.N.; Wen, H.C.; Luan, H.F.; Choi, K.; Harris, H.R.; Senzaki, Y.; Majhi, P.; Lee, B.H.; Foran, B.; Lian, G.

2006-01-01

The effect of device fabrication temperature on the work function of ruthenium (Ru) metal gate and its bilayers was investigated. The work function shows strong temperature dependence when Ru electrodes are deposited on silicon oxide, SiO 2 , but not on hafnium silicates (HfSiO x ). Specifically, the work function of Ru on SiO 2 increased from 4.5 eV at 500 deg. C to 5.0 eV at 700 deg. C. On further annealing to 900 deg. C or higher, the work function dropped to about 4.4 eV. In the case of HfSiO x , the work function of Ru changed by less than 100 mV over the same temperature range. Identical temperature dependence was observed using hafnium (Hf)/Ru and tantalum (Ta)/Ru bilayers. However, the peak values of the work function decreased with increasing Hf/Ru and Ta/Ru thickness ratios. Materials analysis suggests that these trends are driven by interactions at the Ru metal gate-dielectric interface

Experience of CR and RCCA operation in Ukrainian WWER-1000: Aspects of reliability, safety and economic efficiency

International Nuclear Information System (INIS)

Afanasyev, A.

2000-01-01

The next topics are represented in the paper: A brief history of WWER-1000 control rod (CR) and WWER-1000 rod cluster control assembly (RCCA) design; Evolution of WWER-1000 CR manufacturing technology and design; Experience of RCCA operation; Lifetime extension of WWER-1000 boron carbide CR; WWER-1000 reactor core operation problems due to partial RCCA insertion; Designing and licensing procedures and first operational experience of WWER-1000 RCCA (CR) with a combined absorber 'boron carbide-hafnium' and a chromium-nickel alloy cladding. The main conclusions are: Fuel assembly (FA) bow is the main reason of partial RCCA insertion during reactor core operation. However, the use of the RCCA and its driver bar with increased dead load, alongside with other measures, allow to reduce the probability of incomplete RCCA insertion; The materials used in CRs of RCCA in existing reactor operating modes have been working reliably; The use of hafnium under an appropriate price policy can give certain economic advantages for the Ukrainian NPPs, however, additional research is needed in order to confirm the specific CR physical characteristics and reliability. (author)

Synthesis and silica coating of calcia-doped ceria/plate-like titanate (K0.8Li0.27Ti1.73O4) nanocomposite by seeded polymerization technique

International Nuclear Information System (INIS)

El-Toni, Ahmed Mohamed; Yin, Shu; Sato, Tsugio

2007-01-01

Calcia-doped ceria is of potential interest as an ultraviolet (UV) radiation blocking material in personal care products because of the excellent UV light absorption property and low catalytic ability for the oxidation of organic materials superior to undoped ceria. In order to reduce the oxidation catalytic activity further, calcia-doped ceria was coated with amorphous silica by means of seeded polymerization technique. Generally, nanoparticles of inorganic materials do not provide a good coverage for human skin because of the agglomeration of the particles. The plate-like particles are required to enhance the coverage ability of inorganic materials. This can be accomplished by synthesis of calcia-doped ceria/plate-like potassium lithium titanate (K 0.8 Li 0.27 Ti 1.73 O 4 ) nanocomposite with subsequent silica coating to control catalytic activity of calcia-doped ceria. Calcia-doped ceria/plate-like potassium lithium titanate nanocomposite was prepared by soft chemical method followed by silica coating via seeded polymerization technique. Silica coated calcia-doped ceria/plate-like potassium lithium titanate nanocomposite was characterized by X-ray diffraction, SEM, TEM, XPS and FT-IR

Luminescence of Ce doped oxygen crystalline compounds based on Hf and Ba

CERN Document Server

Borisevich, A E; Lecoq, P

2003-01-01

The luminescence properties of the Ce-doped hafnium and barium compounds have been investigated to determine their potential as heavy scintillation materials. Compounds have been prepared by solid state synthesis. All of them have shown a bright luminescence attributed to trivalent cerium. Emission bands are peaked in the 425-475nm spectral region at room temperature.

Activation Analysis of Aluminium

Energy Technology Data Exchange (ETDEWEB)

Brune, Dag

1961-01-15

An analysis of pure aluminium alloyed with magnesium was per- formed by means of gamma spectrometry , Chemical separations were not employed. The isotopes to be determined were obtained in conditions of optimum activity by suitably choosing the time of irradiation and decay. The following elements were detected and measured quantitatively: Iron, zinc, copper, gallium, manganese, chromium, scandium and hafnium.

Neutron-Activation Analysis of Biological Material with High Radiation Levels

Energy Technology Data Exchange (ETDEWEB)

Samsahl, K

1966-09-15

A method has been developed for the chemical separation and subsequent gamma-spectrometric analysis of the alkali metals, the alkaline earths, the rare earths, chromium, hafnium, lanthanum, manganese, phosphorus, scandium and silver in neutron-activated biological material. The separation steps, being fully automatic, are based on a combination of ion-exchange and partition chromatography and require 40 min.

Process and operating device for an apparatus using a running liquid film and application to separation of Zr and Hf tetrachlorides

International Nuclear Information System (INIS)

Brun, R.

1989-01-01

A process is claimed allowing to maintain a thin film in a running film exchanger, by increasing the flow rate for a short time to establish a film all over the surface. Application is made to continuous condensation of zirconium and hafnium tetrachlorides, from the separation column, by absorption in a liquid solvent made of potassium chloroaluminate [fr

Neutron-Activation Analysis of Biological Material with High Radiation Levels

International Nuclear Information System (INIS)

Samsahl, K.

1966-09-01

A method has been developed for the chemical separation and subsequent gamma-spectrometric analysis of the alkali metals, the alkaline earths, the rare earths, chromium, hafnium, lanthanum, manganese, phosphorus, scandium and silver in neutron-activated biological material. The separation steps, being fully automatic, are based on a combination of ion-exchange and partition chromatography and require 40 min

Passive behaviour of zirconium, hafnium and niobium

International Nuclear Information System (INIS)

Hornkjoel, S.

1990-01-01

The paper deals mainly with the results of stationary and transient polarization measurements together with capacitance measurements on passive electrodes of Zr, Hf and Nb over the entire pH-scale. The passive current densities are exstremely low, and essentially both pH and potential independent, exept for Nb at high pH. The extrapolated potential of zero inverse capacitance seems to be different from the extrapolated potential of zero film thickness for Zr and Hf, but not for Nb. The potential versus time curves at constant current show a downwards bending for Zr and Hf. It is shown that the pitting potentials of Zr and Hf are dependent of the concentration of halide ions and the type of halide ion, but not on pH. It is also shown that the pitting induction is second-order stimulated by chloride ions and first-order hindered by sulphate ions. Results from electron transfer reactions on passive niobium are reported. 9 refs

Test report dot7A type A liquid packaging

Energy Technology Data Exchange (ETDEWEB)

Ketusky, E. T. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Brandjes, C. [Ameriphysics LLC, Knoxville, TN (United States); Benoit, T. J. [Argonne National Lab. (ANL), Argonne, IL (United States)

2017-09-19

This section presents a general description of the DOT Specification 7A Type A liquid content packaging (HVYTAL), the liquid content evaluated as its payload, acceptable payload shipping configurations and features special to its use. This test report documents compliance with the regulatory safety requirements of 49 CFR Parts 173.24, 173.24a, 173.27, 173.410, 173.412, 173.461 – 173.466 and 178.350.

PEMISAHAN Zr – Hf SECARA SINAMBUNG MENGGUNAKAN MIXER SETTLER

Directory of Open Access Journals (Sweden)

Dwi Biyantoro

2017-01-01

Full Text Available ABSTRAK PEMISAHAN Zr – Hf SECARA SINAMBUNG MENGGUNAKANMIXER SETTLER. Telah dilakukan pemisahanZr – Hf secara sinambung menggunakan pengaduk pengenap (mixer settler 16 stage. Larutan umpan adalah zirkon nitrat dengan kadar Zr = 30786 ppm dan Hf = 499 ppm. Ekstraktan dipakai adalah solven 60 % TBP dalam kerosen dan larutan scrubbingyang dipakai adalah asam nitrat 1 M. Umpan masuk pada stageke 5 dikontakkan secara berlawanan arah dengan solven masuk pada stage ke 16 dan larutan scrubbing masuk pada stage ke 1. Tujuan penelitian ini adalah memisahkan unsur Zr dan Hf dari hasil olah pasir zirkon menggunakan solven TBP dengan alat mixer settler16 stage. Analisis umpan dan hasil proses pemisahan untuk zirkonium (Zr dilakukan dengan menggunakan alat pendar sinar-X, sedangkananalisis unsur hafnium (Hf menggunakan Analisis Pengaktifan Neutron (APN. Parameter penelitian dilakukan dengan variasi keasaman asam nitrat dalam umpan dan variasi waktu pada berbagai laju pengadukan. Hasil penelitian pemisahan unsur Zr dengan Hf diperolehkondisi optimum pada keasaman umpan 4 N HNO3, keseimbangan dicapai setelah 3jam dan laju pengadukan 3300 rpm. Hasil ekstrak  unsur zirkon (Zr diperoleh kadar sebesar 28577 ppm dengan efisiensi 92,76 % serta kadar pengotor hafnium (Hf sebesar 95 ppm. Kata Kunci: pemisahan Zr, Hf, ekstraksi, mixer settler, alat pendar sinar-X, APN. ABSTRACT SEPARATION of Zr - Hf CONTINUOUSLY USE THE MIXER SETTLER. Separation of Zr - Hf continuously using mixer settler 16 stage has been done. The feed solution is zircon nitrate concentration of Zr = 30786 ppm  and Hf = 499 ppm. As the solvent used extractant 60 % TBP in 40 % kerosene. Nitric acid solution used srubbing 1 M. The feed entered into stage to 5 is contacted with solvents direction on the stage to 16 and the scrubbing solution enter the stage to 1. The purpose of this study is to separate Zr and Hf of the results from the process of zircon sand using solvent TBP using 16 stage

Successive composition of two laser channels upon excitation of He-Ar-Xe (2.03 μm) and Ar-Xe (1.73 μm) mixtures by uranium fission fragments

International Nuclear Information System (INIS)

Pikulev, A A; Tsvetkov, V M; Sosnin, P V; Sinyanskii, A A

2009-01-01

The operation efficiency of the scheme with successive composition of two laser channels upon excitation of the active medium by uranium-235 fission fragments is studied experimentally and numerically. For the He:Ar:Xe = 380:380:1 mixture (at a pressure of 1 atm and the lasing wavelength λ = 2.03 μm) the maximum lasing power of a double channel (1 kW) is almost twice that of a single channel (540 W). Calculations show that in the case of ideal composition (without losses on mirrors) the lasing power of the double channel can be increased to 1.2 kW. For the Ar:Xe = 380:1 mixture (the pressure is 0.5 atm, λ = 1.73 μm) the maximum lasing power of the double channel (620 W) is slightly above that of the single channel (520 W), which is caused by the losses on aluminum mirrors employed for channel doubling and by a negative effect of optical inhomogeneities. In the case of ideal composition, the lasing power can be increased to 830 W. (lasers)

40 CFR 421.333 - Effluent limitations guidelines representing the degree of effluent reduction attainable by the...

Science.gov (United States)

2010-07-01

... 2.387 1.108 Nickel 4.688 3.154 Ammonia (as N) 1,136.000 499.500 (d) SiCl4 purification wet air... air pollution control. BAT Limitations for the Primary Zirconium and Hafnium Subcategory Pollutant or... 0.159 0.074 Nickel 0.312 0.210 Ammonia (as N) 75.710 33.280 (b) Sand chlorination off-gas wet air...

Removal of iron contaminant from zirconium chloride solution

International Nuclear Information System (INIS)

Voit, D.O.

1992-01-01

This patent describes a process for eliminating iron contaminant from an aqueous zirconium chloride solution that has been contaminated with FeCl 3 in a plant in which zirconium and hafnium chloride solutions are separated by a main MINK solvent extraction system and the FeCl 3 is normally removed from the zirconium chloride solution by a secondary MINK solvent extraction system

Artificial Composites for High Temperature Applications; A Review (Composites Artificiels Destines a des Applications a Haute Temperature; Un Expose),

Science.gov (United States)

1987-01-01

ceramic fibres and whiskers including silicon carbide, aluminium oxide, zirconium oxide, hafnium oxide and uranium dioxide, were being considered as...3.1.3 Fabrication Processes.................................. 9 3.1.4 Wire/Matrix Interactions and diffusion barriers ........ 10 3.1.5 Mechanical...20 3.2.1 Fibres, Matrices and Fabrication Processes ............ 20 3.2.2 Fibre/Matrix Interaction and Properties............... 21 3.3 Ductile

Contribution to development of SPNDs for instantaneous and selective measurement of different radiation fields in nuclear reactors; Contribution au developpement de collectrons pour la mesure instantanee et selective des differents champs de rayonnements en reacteurs nucleaires

Energy Technology Data Exchange (ETDEWEB)

Blandin, Christophe [Institut National Polytechnique, 38 - Grenoble (France)

1998-02-20

The objective of this work was conceiving and experimentally optimizing the SPNDs (Self-Powdered Neutron Detector) able to control fast power transients in test reactors and also to cope with requirements of surveillanceand protection of EDF reactors. Thus, different SPND emitters of platinum, gadolinium, hafnium and cobalt were provided according to their nature with sheathing and stainless steel plugs as well as with zirconium over-sheathing in order to render them faster, more selective and adapted for wear checking. Special experimental devices were designed for measuring inside the Siloe reactor the promptness of the signals from SPND, on one hand, and their sensitivity to thermal and epithermal neutrons as well as to gamma rays, on the other hand. The follow-up of power transients in test reactors is ensured by the instantaneous measurement of thermal and epithermal neutron flux as well as of gamma field by means of three special SPND with gadolinium, hafnium and platinum. Also, we have defined the characteristics of a new SPND with cobalt, that delivers a current of unique neutronic origin, able to ensure the surveillance and protection of a power reactor over a period of at least six years.

Contribution to development of SPNDs for instantaneous and selective measurement of different radiation fields in nuclear reactors

International Nuclear Information System (INIS)

Blandin, Christophe

1998-01-01

The objective of this work was conceiving and experimentally optimizing the SPNDs (Self-Powdered Neutron Detector) able to control fast power transients in test reactors and also to cope with requirements of surveillance and protection of EDF reactors. Thus, different SPND emitters of platinum, gadolinium, hafnium and cobalt were provided according to their nature with sheathing and stainless steel plugs as well as with zirconium over-sheathing in order to render them faster, more selective and adapted for wear checking. Special experimental devices were designed for measuring inside the Siloe reactor the promptness of the signals from SPND, on one hand, and their sensitivity to thermal and epithermal neutrons as well as to gamma rays, on the other hand. The follow-up of power transients in test reactors is ensured by the instantaneous measurement of thermal and epithermal neutron flux as well as of gamma field by means of three special SPND with gadolinium, hafnium and platinum. Also, we have defined the characteristics of a new SPND with cobalt, that delivers a current of unique neutronic origin, able to ensure the surveillance and protection of a power reactor over a period of at least six years

Electrical characterisation of ferroelectric field effect transistors based on ferroelectric HfO2 thin films

International Nuclear Information System (INIS)

Yurchuk, Ekaterina

2015-01-01

Ferroelectric field effect transistor (FeFET) memories based on a new type of ferroelectric material (silicon doped hafnium oxide) were studied within the scope of the present work. Utilisation of silicon doped hafnium oxide (Si:HfO 2 ) thin films instead of conventional perovskite ferroelectrics as a functional layer in FeFETs provides compatibility to the CMOS process as well as improved device scalability. The influence of different process parameters on the properties of Si:HfO 2 thin films was analysed in order to gain better insight into the occurrence of ferroelectricity in this system. A subsequent examination of the potential of this material as well as its possible limitations with the respect to the application in non-volatile memories followed. The Si:HfO 2 -based ferroelectric transistors that were fully integrated into the state-of-the-art high-k metal gate CMOS technology were studied in this work for the first time. The memory performance of these devices scaled down to 28 nm gate length was investigated. Special attention was paid to the charge trapping phenomenon shown to significantly affect the device behaviour.

Electrical characterisation of ferroelectric field effect transistors based on ferroelectric HfO{sub 2} thin films

Energy Technology Data Exchange (ETDEWEB)

Yurchuk, Ekaterina

2015-02-06

Ferroelectric field effect transistor (FeFET) memories based on a new type of ferroelectric material (silicon doped hafnium oxide) were studied within the scope of the present work. Utilisation of silicon doped hafnium oxide (Si:HfO{sub 2}) thin films instead of conventional perovskite ferroelectrics as a functional layer in FeFETs provides compatibility to the CMOS process as well as improved device scalability. The influence of different process parameters on the properties of Si:HfO{sub 2} thin films was analysed in order to gain better insight into the occurrence of ferroelectricity in this system. A subsequent examination of the potential of this material as well as its possible limitations with the respect to the application in non-volatile memories followed. The Si:HfO{sub 2}-based ferroelectric transistors that were fully integrated into the state-of-the-art high-k metal gate CMOS technology were studied in this work for the first time. The memory performance of these devices scaled down to 28 nm gate length was investigated. Special attention was paid to the charge trapping phenomenon shown to significantly affect the device behaviour.

Spatial conductivity mapping of unprotected and capped black phosphorus using microwave microscopy

International Nuclear Information System (INIS)

Visser, Pieter J de; Chua, Rebekah; Island, Joshua O; Finkel, Matvey; Katan, Allard J; Thierschmann, Holger; Zant, Herre S J van der; Klapwijk, Teun M

2016-01-01

Thin layers of black phosphorus present an ideal combination of a 2D material with a tunable direct bandgap and high carrier mobility. However the material suffers from degradation in ambient conditions due to an oxidation reaction which involves water, oxygen and light. We have measured the spatial profile of the conductivity on flakes of black phosphorus as a function of time using scanning microwave impedance microscopy. A microwave excitation (3 GHz) allows to image a conducting sample even when covered with a dielectric layer. We observe that on bare black phosphorus, the conductivity changes drastically over the whole surface within a day. We demonstrate that the degradation process is slowed down considerably by covering the material with a 10 nm layer of hafnium oxide. It is stable for more than a week, opening up a route towards stable black phosphorus devices in which the high dielectric constant of hafnium oxide can be exploited. Covering black phosphorus with a 15 nm boron nitride flake changes the degradation process qualitatively, it is dominated by the edges of the flake indicating a diffusive process and happens on the scale of days. (letter)

Morphological Studies of Local Influence of Implants with Coatings Based on Superhard Compounds on Bone Tissue under Conditions of Induced Trauma

Directory of Open Access Journals (Sweden)

Galimzyan KABIROV

2015-07-01

Full Text Available In this paper we analyze the response of bone tissue to a transosseous introduction of implants made of copper (Cu, medical steel 12X18H9T, steel with nitrides of titanium and hafnium coatings (TiN + HfN, as well as steel coated with titanium and zirconium nitrides (TiN + ZrN into the diaphysis of the tibia of experimental rats. The obtained results showed that the restoration of the injured bone and bone marrow in groups with implants made of steel 12X18H9T occurred without the participation of the granulation and cartilaginous tissues, but with implants made of steel coated with titanium and hafnium nitrides (TiN + HfN, this bone recovery also took place in the early term. At the same time, in groups, where the implants were made of copper (Cu, implants were made of steel coated with titanium and zirconium nitrides (TiN + ZrN were used, such phenomena as necrosis, lysis and destruction of the bone were registered and the bone tissue repair went through formation of the cartilaginous tissue.

Neutronic design of pulse operation simulating device for in-pile functional test of fusion blanket by MCNP

Energy Technology Data Exchange (ETDEWEB)

Nagao, Yoshiharu; Nakamichi, Masaru; Kawamura, Hiroshi [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan)

2000-03-01

The pulse operation of a fusion reactor can be simulated in a fission reactor by controlling the neutron flux entering a test section by using a rotating 'hollow cylinder with window' made of hafnium. The rotating cylinder is installed between the test section and the fixed outer neutron absorber cylinder and is also made of hafnium with an opening in the direction to the core center. For gathering engineering data for the tritium breeding blanket such as characteristics of temperature change, tritium release and recovery, etc., it is desirable that the ratio of minimum to maximum thermal neutron fluxes is greater than 1:10. Design calculations were performed for the test assembly which considered local neutronic effects and the mechanical constraints of the device. From the results of these calculations, the ratio of minimum to maximum thermal neutron flux under irradiation would be about 1:10 using a pulse operation simulating device which has a thickness of 6.5 mm and a 150deg window angle for the rotating hollow cylinder and 5.0 mm in thickness of fixed neutron absorber. (author)

Thermal effects on the Raman phonon of few-layer phosphorene

International Nuclear Information System (INIS)

Ling, Zhi-Peng; Ang, Kah-Wee

2015-01-01

Two-dimensional phosphorene is a promising channel material for next generation transistor applications due to its superior carrier transport property. Here, we report the influence of thermal effects on the Raman phonon of few-layer phosphorene formed on hafnium-dioxide (HfO 2 ) high-k dielectric. When annealed at elevated temperatures (up to 200 °C), the phosphorene film was found to exhibit a blue shift in both the out-of-plane (A 1 g ) and in-plane (B 2g and A 2 g ) phonon modes as a result of compressive strain effect. This is attributed to the out-diffusion of hafnium (Hf) atoms from the underlying HfO 2 dielectric, which compresses the phosphorene in both the zigzag and armchair directions. With a further increase in thermal energy beyond 250 °C, strain relaxation within phosphorene eventually took place. When this happens, the phosphorene was unable to retain its intrinsic crystallinity prior to annealing, as evident from the broadening of full-width at half maximum of the Raman phonon. These results provide an important insight into the impact of thermal effects on the structural integrity of phosphorene when integrated with high-k gate dielectric

Preparation of thermoluminescent materials

International Nuclear Information System (INIS)

1976-01-01

Thermoluminescent materials have been found to be suitable for measuring long term exposures to low level ionizing radiation. Oxyhalides of lanthanum, gadolinium and yttrium, including the oxychlorides and oxybromides are activated with terbium and have been found to be most efficient oxygendominated phosphors having thermoradiant efficiencies with excitation by low level ionizing radiation. Thermoluminescence response increases when the previous materials have hafnium and zirconium additives

Dispersion engineering of thick high-Q silicon nitride ring-resonators via atomic layer deposition.

Science.gov (United States)

Riemensberger, Johann; Hartinger, Klaus; Herr, Tobias; Brasch, Victor; Holzwarth, Ronald; Kippenberg, Tobias J

2012-12-03

We demonstrate dispersion engineering of integrated silicon nitride based ring resonators through conformal coating with hafnium dioxide deposited on top of the structures via atomic layer deposition. Both, magnitude and bandwidth of anomalous dispersion can be significantly increased. The results are confirmed by high resolution frequency-comb-assisted-diode-laser spectroscopy and are in very good agreement with the simulated modification of the mode spectrum.

A Search for Technosignatures from 14 Planetary Systems in the Kepler Field with the Green Bank Telescope at 1.15–1.73 GHz

Science.gov (United States)

Margot, Jean-Luc; Greenberg, Adam H.; Pinchuk, Pavlo; Shinde, Akshay; Alladi, Yashaswi; Prasad MN, Srinivas; Bowman, M. Oliver; Fisher, Callum; Gyalay, Szilard; McKibbin, Willow; Miles, Brittany; Nguyen, Donald; Power, Conor; Ramani, Namrata; Raviprasad, Rashmi; Santana, Jesse; Lynch, Ryan S.

2018-05-01

Analysis of Kepler mission data suggests that the Milky Way includes billions of Earth-sized planets in the habitable zone of their host stars. Current technology enables the detection of technosignatures emitted from a large fraction of the Galaxy. We describe a search for technosignatures that is sensitive to Arecibo-class transmitters located within ∼420 ly of Earth and transmitters that are 1000 times more effective than Arecibo within ∼13000 ly of Earth. Our observations focused on 14 planetary systems in the Kepler field and used the L-band receiver (1.15–1.73 GHz) of the 100 m diameter Green Bank Telescope. Each source was observed for a total integration time of 5 minutes. We obtained power spectra at a frequency resolution of 3 Hz and examined narrowband signals with Doppler drift rates between ±9 Hz s‑1. We flagged any detection with a signal-to-noise ratio in excess of 10 as a candidate signal and identified approximately 850,000 candidates. Most (99%) of these candidate signals were automatically classified as human-generated radio-frequency interference (RFI). A large fraction (>99%) of the remaining candidate signals were also flagged as anthropogenic RFI because they have frequencies that overlap those used by global navigation satellite systems, satellite downlinks, or other interferers detected in heavily polluted regions of the spectrum. All 19 remaining candidate signals were scrutinized and none were attributable to an extraterrestrial source.

Finding of 13(2) , 17(3) -cyclopheophorbide a enol as a degradation product of chlorophyll in shrunk zooxanthellae of the coral Montipora digitata.

Science.gov (United States)

Suzuki, Toshiyuki; Casareto, Beatriz Estela; Shioi, Yuzo; Ishikawa, Yoshio; Suzuki, Yoshimi

2015-02-01

We examined the morphology and pigment composition of zooxanthellae in corals subjected to normal temperature (27°C) and thermal stress (32°C). We observed several normal and abnormal morphological types of zooxanthellar cells. Normal cells were intact and their chloroplasts were unbroken (healthy); abnormal cells were shrunken and had partially degraded or broken chloroplasts, or they were bleached and without chloroplasts. At 27°C, most healthy zooxanthellar cells were retained in the coral tissue, whereas shrunken zooxanthellae were expelled. Under thermal stress, the abundance of healthy zooxanthellae declined and the proportion of shrunken/abnormal cells increased in coral tissues. The rate of algal cell expulsion was reduced under thermal stress. Within the shrunken cells, we detected the presence of a chl-like pigment that is not ordinarily found in healthy zooxanthellae. Analysis of the absorption spectrum, absorption maxima, and retention time (by HPLC) indicated that this pigment was 13(2) , 17(3) -cyclopheophorbide a enol (cPPB-aE), which is frequently found in marine and lacustrine sediments, and in protozoans that graze on phytoplankton. The production of cPPB-aE in shrunken zooxanthellae suggests that the chls have been degraded to cPPB-aE, a compound that is not fluorescent. The lack of a fluorescence function precludes the formation of reactive oxygen species. We therefore consider the formation of cPPB-aE in shrunken zooxanthellae to be a mechanism for avoiding oxidative stress. © 2014 The Authors. Journal of Phycology published by Wiley Periodicals, Inc. on behalf of Phycological Society of America.

Effect of a fermented milk containing Bifidobacterium animalis DN-173 010 on the health-related quality of life and symptoms in irritable bowel syndrome in adults in primary care: a multicentre, randomized, double-blind, controlled trial.

Science.gov (United States)

Guyonnet, D; Chassany, O; Ducrotte, P; Picard, C; Mouret, M; Mercier, C-H; Matuchansky, C

2007-08-01

Health-related quality of life (HRQoL) has been rarely evaluated as a primary endpoint in the assessment of the effect of probiotics on the irritable bowel syndrome (IBS). To study the effects of fermented milk containing Bifidobacterium animalis DN-173 010 and yoghurt strains on the IBS in a multicentre, double-blind, controlled trial. A total of 274 primary care adults with constipation-predominant IBS (Rome II) were randomized to consume for 6 weeks either the test fermented milk or a heat-treated yoghurt (control). HRQoL and digestive symptoms were assessed after 3 and 6 weeks on an intention-to-treat population of 267 subjects. The HRQoL discomfort score, the primary endpoint, improved (P food on discomfort HRQoL score and bloating in constipation-predominant IBS, and on stool frequency in subjects with <3 stools/week.

Hafnium Isotopic Variations in Central Atlantic Intraplate Volcanism

Science.gov (United States)

Geldmacher, J.; Hanan, B. B.; Hoernle, K.; Blichert-Toft, J.

2008-12-01

Although one of the geochemically best investigated volcanic regions on Earth, almost no Hf isotopic data have been published from the broad belt of intraplate seamounts and islands in the East Atlantic between 25° and 36° N. This study presents 176Hf/177Hf ratios from 61 representative samples from the Canary, Selvagen and Madeira Islands and nearby large seamounts, encompassing the full range of different evolutionary stages and geochemical endmembers. The majority of samples have mafic, mainly basaltic compositions with Mg-numbers within or near the range of magmas in equilibrium with mantle olivine (68-75). No correlation was found between Mg-number and 176Hf/177Hf ratios in the data set. In comparison to observed Nd isotope variations published for this volcanic province (6 ɛNd units), 176Hf/177Hf ratios span a larger range (14 ɛHf units). Samples from the Madeira archipelago have the most radiogenic compositions (176Hf/177Hfm= 0.283132-0.283335), widely overlapping the field for central Atlantic N-MORB. They form a relatively narrow, elongated trend (stretching over >6 ɛHf units) between a radiogenic MORB-like endmember and a composition located on the Nd-Hf mantle array. In contrast, all Canary Islands samples plot below the mantle array (176Hf/177Hfm = 0.282943-0.283067) and, despite being from an archipelago that stretches over a much larger geographic area, form a much denser cluster with less compositional variation (~4 ɛHf units). All samples from the seamounts NE of the Canaries, proposed to belong to the same Canary hotspot track (e.g. Geldmacher et al., 2001, JVGR 111; Geldmacher et al., 2005, EPSL 237), fall within the Hf isotopic range of this cluster. The cluster largely overlaps the composition of the proposed common mantle endmember 'C' (Hanan and Graham, 1996, Science 272) but spans a space between a more radiogenic (depleted) composition and a HIMU-type endmember. Although samples of Seine and Unicorn seamounts, attributed to the Madeira hotspot track, show less radiogenic Hf and Nd isotope ratios than Madeira, their isotopic compositions lie along an extension of the Madeira trend in plots of Hf versus Sr, Nd, Pb isotopes. The new Hf isotope ratios confirm the existence of at least two geochemically distinct volcanic provinces (Canary and Madeira) in the East Atlantic as previously proposed.

Hafnium isotope ratios of nine GSJ reference samples

International Nuclear Information System (INIS)

Hanyu, Takeshi; Nakai, Shun'ichi; Tatsuta, Riichiro

2005-01-01

176 Hf/ 177 Hf ratios of nine geochemical reference rocks from the Geological Survey of Japan, together with BIR-1 and BCR-2, were determined using multi-collector inductively coupled plasma mass spectrometry. Our data for BIR-1, BCR-2 and JB-1 are in agreement with those previously reported, demonstrating the appropriateness of the chemical procedure and isotopic measurement employed in this study. The reference rocks have a wide range of 176 Hf/ 177 Hf covering the field defined by various volcanic rocks, such as mid-ocean ridge basalts, ocean island basalts, and subduction related volcanic rocks. They are therefore suitable as rock standards for Hf isotope measurement of geological samples. (author)

Elastic and Thermodynamic Properties of Zirconium and Hafnium ...

Indian Academy of Sciences (India)

65

Here Rh3V is chosen as the parent binary compound and the doping ..... Grüneisen parameter ζ [44] are two key quantities in solid state problems due to their .... The authors wish to thank DRDO (ER & IPR), New Delhi for the financial support.

Hafnium(IV) complexation with oxalate at variable temperatures

Energy Technology Data Exchange (ETDEWEB)

Friend, Mitchell T.; Wall, Nathalie A. [Washington State Univ., Pullmanm, WA (United States). Dept. of Chemistry

2017-08-01

Appropriate management of fission products in the reprocessing of spent nuclear fuel (SNF) is crucial in developing advanced reprocessing schemes. The addition of aqueous phase complexing agents can prevent the co-extraction of these fission products. A solvent extraction technique was used to study the complexation of Hf(IV) - an analog to fission product Zr(IV) - with oxalate at 15, 25, and 35 C in 1 M HClO{sub 4} utilizing a {sup 175+181}Hf radiotracer. The mechanism of the solvent extraction system of 10{sup -5} M Hf(IV) in 1 M HClO{sub 4} to thenoyltrifluoroacetone (TTA) in toluene demonstrated a 4{sup th}-power dependence in both TTA and H{sup +}, with Hf(TTA){sub 4} the only extractable species. The equilibrium constant for the extraction of Hf(TTA){sub 4} was determined to be log K{sub ex}=7.67±0.07 (25±1 C, 1 M HClO{sub 4}). The addition of oxalate to the aqueous phase decreased the distribution ratio, indicating aqueous Hf(IV)-oxalate complex formation. Polynomial fits to the distribution data identified the formation of Hf(ox){sup 2+} and Hf(ox){sub 2(aq)} and their stability constants were measured at 15, 25, and 35 C in 1 M HClO{sub 4}. van't Hoff analysis was used to calculate Δ{sub r}G, Δ{sub r}H, and Δ{sub r}S for these species. Stability constants were observed to increase at higher temperature, an indication that Hf(IV)-oxalate complexation is endothermic and driven by entropy.

Electric field cycling behavior of ferroelectric hafnium oxide.

Science.gov (United States)

Schenk, Tony; Schroeder, Uwe; Pešić, Milan; Popovici, Mihaela; Pershin, Yuriy V; Mikolajick, Thomas

2014-11-26

HfO2 based ferroelectrics are lead-free, simple binary oxides with nonperovskite structure and low permittivity. They just recently started attracting attention of theoretical groups in the fields of ferroelectric memories and electrostatic supercapacitors. A modified approach of harmonic analysis is introduced for temperature-dependent studies of the field cycling behavior and the underlying defect mechanisms. Activation energies for wake-up and fatigue are extracted. Notably, all values are about 100 meV, which is 1 order of magnitude lower than for conventional ferroelectrics like lead zirconate titanate (PZT). This difference is mainly atttributed to the one to two orders of magnitude higher electric fields used for cycling and to the different surface to volume ratios between the 10 nm thin films in this study and the bulk samples of former measurements or simulations. Moreover, a new, analog-like split-up effect of switching peaks by field cycling is discovered and is explained by a network model based on memcapacitive behavior as a result of defect redistribution.

Electronic structure of hafnium: A Compton profile study

Indian Academy of Sciences (India)

To extract the true Compton profile from the raw data, the raw data were cor- rected for ... For the present sample and experimental conditions, the contribution of .... are in better agreement with the simple renormalized free atom calculations for.

Neutron Detection Utilizing Gadolinium Doped Hafnium Oxide Films

National Research Council Canada - National Science Library

Blasy, Bryan D

2008-01-01

... retains monoclinic local symmetery for all levels of doping. Current as a function of voltage experiments identified the films as having poor diode characteristics with high leakage current in the forward bias region...

Elastic and thermodynamic properties of zirconium- and hafnium ...

Indian Academy of Sciences (India)

2018-02-02

Feb 2, 2018 ... ties. The volume optimization curves (both LDA and GGA) for binary Rh3V, Rh3Zr and Rh3Hf compounds are shown in ... the strength of covalent bonding of the given material. ..... Bulk modulus is correlated with binding energy or cohesive energy of atoms, since it is a measure of average atomic bond.

A new position-sensitive detector for thermal and epithermal neutrons

International Nuclear Information System (INIS)

Jeavons, A.P.; Ford, N.L.; Lindberg, B.; Sachot, R.

1977-01-01

A new two-dimensional position-sensitive neutron detector is described. It is based on (n,γ) neutron resonance capture in a foil with subsequent detection of internal conversion electrons with a high-density proportional chamber. Large-area detectors with a 1 mm spatial resolution are feasible. A detection efficiency of 50% is possible for thermal neutrons using gadolinium-157 foil and for epithermal neutrons using hafnium-177. (Auth.)

Composites having an intermetallic containing matrix

International Nuclear Information System (INIS)

Nagle, D.C.; Brupbacher, J.M.; Christodoulou, L.

1990-01-01

This paper describes a composite material. It comprises: a dispersion of in-situ precipitated second phase particles selected from the group consisting of borides, carbides, nitrides, and sulfides, in an intermetallic containing matrix selected from the group consisting of the aluminides, silicides, and beryllides of nickel, copper, titanium, cobalt, iron, platinum, gold, silver, niobium, tantalum, zinc, molybdenum, hafnium, tin, tungsten, lithium, magnesium, thorium, chromium, vanadium, zirconium, and manganese

173 - 177 Falodun J

African Journals Online (AJOL)

DR. AMIN

palm oil mill effluent and NPK 15:15:15 fertilizer on the growth and yield of soyabean genotype ... growing maize and reported a significant effect on yield. Organic fertilizers supply the ... (1984) and significant differences among treatment.

Pages 166- 173.pmd

African Journals Online (AJOL)

Administrator

The logistic regression model to predict neonatal mortality had a good fit (AUC: 0.8507, misclassification rate: 13.6%) ... intensive care units, principal component analysis, logistic regression, ... between cost of neonatal care and length of stay.

Prediction of presence of kidney disease in a general patient population undergoing intravenous iodinated contrast enhanced computed tomography

Energy Technology Data Exchange (ETDEWEB)

Moos, Shira I.; Stoker, Jaap; Nagan, Gajenthiran; Weijert, Roderick S. de; Vemde, David N.H. van; Bipat, Shandra [Academic Medical Center, University of Amsterdam, Department of Radiology, G1-215, Amsterdam (Netherlands)

2014-06-15

To assess which risk factors can be used to reduce superfluous estimated glomerular filtration rate (eGFR) measurements before intravenous contrast medium administration. In consecutive patients, all decreased eGFR risk factors were assessed: diabetes mellitus (DM), history of urologic/nephrologic disease (HUND), nephrotoxic medication, cardiovascular disease, hypertension, age > 60 years, anaemia, malignancy and multiple myeloma/M. Waldenstroem. We studied four models: (1) all risk factors, (2) DM, HUND, hypertension, age > 60 years; (3) DM, HUND, cardiovascular disease, hypertension; (4) DM, HUND, age > 75 years and congestive heart failure. For each model, association with eGFR < 60 ml/min/1.73 m{sup 2} or eGFR < 45 ml/min/1.73 m{sup 2} was studied. A total of 998 patients, mean age 59.94 years were included; 112 with eGFR < 60 ml/min/1.73 m{sup 2} and 30 with eGFR < 45 ml/min/1.73 m{sup 2}. Model 1 detected 816 patients: 108 with eGFR < 60 ml/min/1.73 m{sup 2} and all 30 with eGFR < 45 ml/min/1.73 m{sup 2}. Model 2 detected 745 patients: 108 with eGFR < 60 ml/min/1.73 m{sup 2} and all 30 with eGFR < 45 ml/min/1.73 m{sup 2}. Model 3 detected 622 patients: 100 with eGFR < 60 ml/min/1.73 m{sup 2} and all 30 with eGFR < 45 ml/min/1.73 m{sup 2}. Model 4 detected 440 patients: 86 with eGFR < 60 ml/min/1.73 m{sup 2} and all 30 with eGFR < 45 ml/min/1.73 m{sup 2}. Associations were significant (p < 0.001). Model 4 is most effective, resulting in the lowest proportion of superfluous eGFR measurements while detecting all patients with eGFR < 45 ml/min/1.73 m{sup 2} and most with eGFR < 60 ml/min/1.73 m{sup 2}. (orig.)

Surface layers in the 4A group metals with implanted silicon ions

International Nuclear Information System (INIS)

Kovneristyj, Yu.K.; Vavilova, V.V.; Krasnopevtsev, V.V.; Galkin, L.N.; Kudyshev, A.N.; Klechkovskaya, V.V.

1987-01-01

A study was made on the change of structure and phase composition of fine near the surface layers of 4A group metals (Hf, Zr, Ti) during ion Si implantation and successive thermal annealing at elevated temperatures. Implantation of Si + ions with 30 or 16 keV energy in Ti, Zr and Hf at room temperature results to amorphization of metal surface layer. The surface hafnium and titanium layer with implanted Si atoms due to interaction with residual atmosphere of oxygen turns during annealing at 870 K to amorphous solid solution of HfO 2m or TiO 2 with Si, preventing further metal oxidation; layers of amorphous alloy are characterized by thermal stability up to 1270 K. Oxidation of the surface amorphous layer in residual oxygen atmosphere and its crystallization in ZrO 2 take place in result of Zr annealing with implanted Si ions at temperature not exceeding 870 K. Similar phenomena are observed in the case of hafnium with implanted oxygen ions or small dose of silicon ions. Thermal stability of amorphous layers produced during ion implantation of Si in Ti, Zr and Hf corresponds to scale resistance of monolithic alloys in Ti-Si, Zr-Si and Hf-Si systems

Thermal effects on the Raman phonon of few-layer phosphorene

Energy Technology Data Exchange (ETDEWEB)

Ling, Zhi-Peng; Ang, Kah-Wee, E-mail: eleakw@nus.edu.sg [Department of Electrical and Computer Engineering, National University of Singapore, 4 Engineering Drive 3, Singapore 117583 (Singapore); Centre for Advanced 2D Materials and Graphene Research Centre, National University of Singapore, 6 Science Drive 2, Singapore 117546 (Singapore)

2015-12-01

Two-dimensional phosphorene is a promising channel material for next generation transistor applications due to its superior carrier transport property. Here, we report the influence of thermal effects on the Raman phonon of few-layer phosphorene formed on hafnium-dioxide (HfO{sub 2}) high-k dielectric. When annealed at elevated temperatures (up to 200 °C), the phosphorene film was found to exhibit a blue shift in both the out-of-plane (A{sup 1}{sub g}) and in-plane (B{sub 2g} and A{sup 2}{sub g}) phonon modes as a result of compressive strain effect. This is attributed to the out-diffusion of hafnium (Hf) atoms from the underlying HfO{sub 2} dielectric, which compresses the phosphorene in both the zigzag and armchair directions. With a further increase in thermal energy beyond 250 °C, strain relaxation within phosphorene eventually took place. When this happens, the phosphorene was unable to retain its intrinsic crystallinity prior to annealing, as evident from the broadening of full-width at half maximum of the Raman phonon. These results provide an important insight into the impact of thermal effects on the structural integrity of phosphorene when integrated with high-k gate dielectric.