WorldWideScience

Sample records for groundwater flow analysis

  1. Sensitivity analysis of groundwater flow

    International Nuclear Information System (INIS)

    Bao Yungbing

    1990-12-01

    A sensitivity analysis of general linear and nonlinear simulation equation sets is developed in this study in order to facilitate the application of the sensitivity analysis to groundwater flow problems. Two methods are considered for the sensitivity calculation: the 'direct method' and the 'adjoint method'. Sensitivity theory was used to establish a sensitivity analysis model for general three dimensional transient groundwater flow. Three different methods for calculation of the sensitivity coefficient are presented. The sensitivity equations and the groundwater flow equations were nummerically solved by the Galerkin finite element method in the model. Sensitivity coefficients were carried out both numerically with the developed direct method and with the known analytic solution. Very good agreement between the two solutions was obtained. The developed sensitivity model was applied to three dimensional (axi-symmetric) groundwater flow in a tunnel system, which was supposed to be located at a depth of 500 meters below the ground surface in a four-layered rock formation. In this case, the sensitivity distribution of the piezometric head was calculated with the direct method and the sensitivity of multiple performance functions to perturbations of the permeability were analysed by using the adjoint method. The calculations results showed that the peaks of the sensitivity coefficients appear mostly in the area around the tunnel. The piezometric head at the studied points (nodes) was quite sensitive to perturbations of the permeability in the layer where the points were located, but practically insensitive to perturbations of the permeability in the bottom layer. The flux into the tunnel and the velocity performance were mostly sensitive to perturbation of the permeability in the layer next to the top layer, but practically insensitive to perturbation of the permeability in the bottom layer. (author)

  2. Analysis of groundwater flow beneath ice sheets

    International Nuclear Information System (INIS)

    Boulton, G. S.; Zatsepin, S.; Maillot, B.

    2001-03-01

    The large-scale pattern of subglacial groundwater flow beneath European ice sheets was analysed in a previous report. It was based on a two-dimensional flowline model. In this report, the analysis is extended to three dimensions by exploring the interactions between groundwater and tunnel flow. A theory is developed which suggests that the large-scale geometry of the hydraulic system beneath an ice sheet is a coupled, self-organising system. In this system the pressure distribution along tunnels is a function of discharge derived from basal meltwater delivered to tunnels by groundwater flow, and the pressure along tunnels itself sets the base pressure which determines the geometry of catchments and flow towards the tunnel. The large-scale geometry of tunnel distribution is a product of the pattern of basal meltwater production and the transmissive properties of the bed. The tunnel discharge from the ice margin of the glacier, its seasonal fluctuation and the sedimentary characteristics of eskers are largely determined by the discharge of surface meltwater which penetrates to the bed in the terminal zone. The theory explains many of the characteristics of esker systems and can account for tunnel valleys. It is concluded that the large-scale hydraulic regime beneath ice sheets is largely a consequence of groundwater/tunnel flow interactions and that it is essential similar to non-glacial hydraulic regimes. Experimental data from an Icelandic glacier, which demonstrates measured relationships between subglacial tunnel flow and groundwater flow during the transition from summer to winter seasons for a modern glacier, and which support the general conclusions of the theory is summarised in an appendix

  3. Validation Analysis of the Shoal Groundwater Flow and Transport Model

    Energy Technology Data Exchange (ETDEWEB)

    A. Hassan; J. Chapman

    2008-11-01

    Environmental restoration at the Shoal underground nuclear test is following a process prescribed by a Federal Facility Agreement and Consent Order (FFACO) between the U.S. Department of Energy, the U.S. Department of Defense, and the State of Nevada. Characterization of the site included two stages of well drilling and testing in 1996 and 1999, and development and revision of numerical models of groundwater flow and radionuclide transport. Agreement on a contaminant boundary for the site and a corrective action plan was reached in 2006. Later that same year, three wells were installed for the purposes of model validation and site monitoring. The FFACO prescribes a five-year proof-of-concept period for demonstrating that the site groundwater model is capable of producing meaningful results with an acceptable level of uncertainty. The corrective action plan specifies a rigorous seven step validation process. The accepted groundwater model is evaluated using that process in light of the newly acquired data. The conceptual model of ground water flow for the Project Shoal Area considers groundwater flow through the fractured granite aquifer comprising the Sand Springs Range. Water enters the system by the infiltration of precipitation directly on the surface of the mountain range. Groundwater leaves the granite aquifer by flowing into alluvial deposits in the adjacent basins of Fourmile Flat and Fairview Valley. A groundwater divide is interpreted as coinciding with the western portion of the Sand Springs Range, west of the underground nuclear test, preventing flow from the test into Fourmile Flat. A very low conductivity shear zone east of the nuclear test roughly parallels the divide. The presence of these lateral boundaries, coupled with a regional discharge area to the northeast, is interpreted in the model as causing groundwater from the site to flow in a northeastward direction into Fairview Valley. Steady-state flow conditions are assumed given the absence of

  4. Evolutionary analysis of groundwater flow: Application of multivariate statistical analysis to hydrochemical data in the Densu Basin, Ghana

    Science.gov (United States)

    Yidana, Sandow Mark; Bawoyobie, Patrick; Sakyi, Patrick; Fynn, Obed Fiifi

    2018-02-01

    An evolutionary trend has been postulated through the analysis of hydrochemical data of a crystalline rock aquifer system in the Densu Basin, Southern Ghana. Hydrochemcial data from 63 groundwater samples, taken from two main groundwater outlets (Boreholes and hand dug wells) were used to postulate an evolutionary theory for the basin. Sequential factor and hierarchical cluster analysis were used to disintegrate the data into three factors and five clusters (spatial associations). These were used to characterize the controls on groundwater hydrochemistry and its evolution in the terrain. The dissolution of soluble salts and cation exchange processes are the dominant processes controlling groundwater hydrochemistry in the terrain. The trend of evolution of this set of processes follows the pattern of groundwater flow predicted by a calibrated transient groundwater model in the area. The data suggest that anthropogenic activities represent the second most important process in the hydrochemistry. Silicate mineral weathering is the third most important set of processes. Groundwater associations resulting from Q-mode hierarchical cluster analysis indicate an evolutionary pattern consistent with the general groundwater flow pattern in the basin. These key findings are at variance with results of previous investigations and indicate that when carefully done, groundwater hydrochemical data can be very useful for conceptualizing groundwater flow in basins.

  5. Groundwater flow analysis using mixed hybrid finite element method for radioactive waste disposal facilities

    International Nuclear Information System (INIS)

    Aoki, Hiroomi; Shimomura, Masanori; Kawakami, Hiroto; Suzuki, Shunichi

    2011-01-01

    In safety assessments of radioactive waste disposal facilities, ground water flow analysis are used for calculating the radionuclide transport pathway and the infiltration flow rate of groundwater into the disposal facilities. For this type of calculations, the mixed hybrid finite element method has been used and discussed about the accuracy of ones in Europe. This paper puts great emphasis on the infiltration flow rate of groundwater into the disposal facilities, and describes the accuracy of results obtained from mixed hybrid finite element method by comparing of local water mass conservation and the reliability of the element breakdown numbers among the mixed hybrid finite element method, finite volume method and nondegenerated finite element method. (author)

  6. Study on uncertainty evaluation methodology related to hydrological parameter of regional groundwater flow analysis model

    International Nuclear Information System (INIS)

    Sakai, Ryutaro; Munakata, Masahiro; Ohoka, Masao; Kameya, Hiroshi

    2009-11-01

    In the safety assessment for a geological disposal of radioactive waste, it is important to develop a methodology for long-term estimation of regional groundwater flow from data acquisition to numerical analyses. In the uncertainties associated with estimation of regional groundwater flow, there are the one that concerns parameters and the one that concerns the hydrologeological evolution. The uncertainties of parameters include measurement errors and their heterogeneity. The authors discussed the uncertainties of hydraulic conductivity as a significant parameter for regional groundwater flow analysis. This study suggests that hydraulic conductivities of rock mass are controlled by rock characteristics such as fractures, porosity and test conditions such as hydraulic gradient, water quality, water temperature and that there exists variations more than ten times in hydraulic conductivity by difference due to test conditions such as hydraulic gradient or due to rock type variations such as rock fractures, porosity. In addition this study demonstrated that confining pressure change caused by uplift and subsidence and change of hydraulic gradient under the long-term evolution of hydrogeological environment could possibly produce variations more than ten times of magnitude in hydraulic conductivity. It was also shown that the effect of water quality change on hydraulic conductivity was not negligible and that the replacement of fresh water and saline water caused by sea level change could induce 0.6 times in current hydraulic conductivities in case of Horonobe site. (author)

  7. Stepwise hydrogeological modeling and groundwater flow analysis on site scale (Step 0 and Step 1)

    International Nuclear Information System (INIS)

    Ohyama, Takuya; Saegusa, Hiromitsu; Onoe, Hironori

    2005-05-01

    One of the main goals of the Mizunami Underground Research Laboratory Project is to establish comprehensive techniques for investigation, analysis, and assessment of the deep geological environment. To achieve this goal, a variety of investigations, analysis, and evaluations have been conducted using an iterative approach. In this study, hydrogeological modeling and ground water flow analyses have been carried out using the data from surface-based investigations at Step 0 and Step 1, in order to synthesize the investigation results, to evaluate the uncertainty of the hydrogeological model, and to specify items for further investigation. The results of this study are summarized as follows: 1) As the investigation progresses Step 0 to Step 1, the understanding of groundwater flow was enhanced from Step 0 to Step 1, and the hydrogeological model could be revised, 2) The importance of faults as major groundwater flow pathways was demonstrated, 3) Geological and hydrogeological characteristics of faults with orientation of NNW and NE were shown to be especially significant. The main item specified for further investigations is summarized as follows: geological and hydrogeological characteristics of NNW and NE trending faults are important. (author)

  8. Uncertainty Analysis Framework - Hanford Site-Wide Groundwater Flow and Transport Model

    Energy Technology Data Exchange (ETDEWEB)

    Cole, Charles R.; Bergeron, Marcel P.; Murray, Christopher J.; Thorne, Paul D.; Wurstner, Signe K.; Rogers, Phillip M.

    2001-11-09

    Pacific Northwest National Laboratory (PNNL) embarked on a new initiative to strengthen the technical defensibility of the predictions being made with a site-wide groundwater flow and transport model at the U.S. Department of Energy Hanford Site in southeastern Washington State. In FY 2000, the focus of the initiative was on the characterization of major uncertainties in the current conceptual model that would affect model predictions. The long-term goals of the initiative are the development and implementation of an uncertainty estimation methodology in future assessments and analyses using the site-wide model. This report focuses on the development and implementation of an uncertainty analysis framework.

  9. Groundwater flow analysis and dose rate estimates from releases to wells at a coastal site

    Energy Technology Data Exchange (ETDEWEB)

    Kattilakoski, E.; Suolanen, V. [VTT Energy, Espoo (Finland)

    2000-09-01

    {sup 3}/a. Due to the placing of the shallow wells in the discharge areas, the dilution calculated in the shallow well was shown to be close to that calculated in the deep well. In conservative considerations the value around 90 000 m{sup 3}/a can be regarded as a representative expectation value of the effective dilution of the well. This dilution volume value was also suggested by the most realistic modelling approach of the groundwater flow analysis. It was used as basis when calculating the nuclide specific dose conversion factors (DCF's) for the drinking water pathway. The DCF's were calculated for unit release rates (1 Bq/a) and the assumed water consumption rate was 2 litres/day. (orig.)

  10. Numerical Analysis of Groundwater Ridging Processes Considering Water-Air Flow in a Hillslope.

    Science.gov (United States)

    Zang, Yong Ge; Sun, Dong Mei; Feng, Ping; Semprich, Stephan

    2017-10-09

    In this study, a water-air two-phase flow model was employed to investigate the formation, extension, and dissipation of groundwater ridging induced by recharge events in a hypothetical hillslope-riparian zone, considering interactions between the liquid and gas phases in soil voids. The simulation results show that, after a rain begins, the groundwater table near the stream is elevated instantaneously and significantly, thereby generating a pressure gradient driving water toward both the stream (the discharge of groundwater to the stream) and upslope (the extension of groundwater ridging into upslope). Meanwhile, the airflow upslope triggered by the advancing wetting front moves downward gradually. Therefore, the extension of groundwater ridging into upslope and the downward airflow interact within a certain region. After the rain stops, groundwater ridging near the stream declines quickly while the airflow in the lower part of upslope is still moving into the hillslope. Thus, the airflow upslope mitigates the dissipation of groundwater ridging. Additionally, the development of groundwater ridging under different conditions, including rain intensity, intrinsic permeability, capillary fringe height, and initial groundwater table, was analyzed. Changes in intrinsic permeability affect the magnitude of groundwater ridging near the stream, as well as the downward speed of airflow, thereby generating highly complex responses. The capillary fringe is not a controlling factor but an influence factor on the formation of groundwater ridging, which is mainly related to the antecedent moisture. It was demonstrated that groundwater ridging also occurs where an unsaturated zone occurs above the capillary fringe with a subsurface lateral flow. © 2017, National Ground Water Association.

  11. Monitoring probe for groundwater flow

    Science.gov (United States)

    Looney, B.B.; Ballard, S.

    1994-08-23

    A monitoring probe for detecting groundwater migration is disclosed. The monitor features a cylinder made of a permeable membrane carrying an array of electrical conductivity sensors on its outer surface. The cylinder is filled with a fluid that has a conductivity different than the groundwater. The probe is placed in the ground at an area of interest to be monitored. The fluid, typically saltwater, diffuses through the permeable membrane into the groundwater. The flow of groundwater passing around the permeable membrane walls of the cylinder carries the conductive fluid in the same general direction and distorts the conductivity field measured by the sensors. The degree of distortion from top to bottom and around the probe is precisely related to the vertical and horizontal flow rates, respectively. The electrical conductivities measured by the sensors about the outer surface of the probe are analyzed to determine the rate and direction of the groundwater flow. 4 figs.

  12. Numerical modeling analysis of VOC removal processes in different aerobic vertical flow systems for groundwater remediation

    NARCIS (Netherlands)

    De Biase, C.; Carminati, A.; Oswald, S.E.; Thullner, M.

    2013-01-01

    Vertical flow systems filled with porous medium have been shown to efficiently remove volatile organic contaminants (VOCs) from contaminated groundwater. To apply this semi-natural remediation strategy it is however necessary to distinguish between removal due to biodegradation and due to volatile

  13. Research on fracture analysis, groundwater flow and sorption processes in fractured rocks

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dae-Ha; Kim, Won-Young; Lee, Seung-Gu [Korea Institute of Geology Mining and Materials, Taejon (KR)] (and others)

    1999-12-01

    Due to increasing demand for numerous industrial facilities including nuclear power plants and waste repositories, the feasibility of rocks masses as sites for the facilities has been a geological issue of concern. Rock masses, in general, comprises systems of fractures which can provide pathways for groundwater flow and may also affect the stability of engineered structures. For the study of groundwater flow and sorption processes in fractured rocks, five boreholes were drilled. A stepwise and careful integration of various data obtained from field works and laboratory experiments were carried out to analyze groundwater flow in fractured rocks as follows; (1) investigation of geological feature of the site, (2) identification and characterization of fracture systems using core and televiewer logs, (3) determination of hydrogeological properties of fractured aquifers using geophysical borehole logging, pumping and slug tests, and continuous monitoring of groundwater level and quality, (4) evaluation of groundwater flow patterns using fluid flow modeling. The results obtained from these processes allow a qualitative interpretation of fractured aquifers in the study area. Column experiments of some reactive radionuclides were also performed to examine sorption processes of the radionuclides including retardation coefficients. In addition, analyses of fracture systems covered (1) reconstruction of the Cenozoic tectonic movements and estimation of frequency indices for the Holocene tectonic movements, (2) determination of distributions and block movements of the Quaternary marine terraces, (3) investigation of lithologic and geotechnical nature of study area, and (4) examination of the Cenozoic volcanic activities and determination of age of the dike swarms. Using data obtained from above mentioned analyses along with data related to earthquakes and active faults, probabilistic approach was performed to determine various potential hazards which may result from the

  14. A comparison of uncertainty analysis methods using a groundwater flow model

    International Nuclear Information System (INIS)

    Doctor, P.G.; Jacobson, E.A.; Buchanan, J.A.

    1988-06-01

    This report evaluates three uncertainty analysis methods that are proposed for use in performances assessment activities within the OCRWM and Nuclear Regulatory Commission (NRC) communities. The three methods are Monte Carlo simulation with unconstrained sampling, Monte Carlo simulation with Latin Hypercube sampling, and first-order analysis. Monte Carlo simulation with unconstrained sampling is a generally accepted uncertainty analysis method, but it has the disadvantage of being costly and time consuming. Latin Hypercube sampling was proposed to make Monte Carlo simulation more efficient. However, although it was originally formulated for independent variables, which is a major drawback in performance assessment modeling, Latin Hypercube can be used to generate correlated samples. The first-order method is efficient to implement because it is based on the first-order Taylor series expansion; however, there is concern that it does not adequately describe the variability for complex models. These three uncertainty analysis methods were evaluated using a calibrated groundwater flow model of a unconfined aquifer in southern Arizona. The two simulation methods produced similar results, although the Latin Hypercube method tends to produce samples whose estimates of statistical parameters are closer to the desired parameters. The mean travel times for the first-order method does not agree with those of the simulations. In additions, the first-order method produces estimates of variance in travel times that are more variable than those produced by the simulation methods, resulting in nonconservative tolerance intervals. 13 refs., 33 figs

  15. Groundwater flow analysis using radon-222 existing in environment as an indicator

    International Nuclear Information System (INIS)

    Komae, Takami

    1996-01-01

    Several kinds of isotopes have been used to trace water movement in the hydrology including surface and ground water as indicators. But those are not effective to analyze the contaminant movement with groundwater though short distance in short time owing to long life. Radon ( 222 Rn) existing in environment was chosen for this purpose as an short-lived indicator. Radon is a radioactive gas, with a half life of 3.8 days, generated from radium ( 226 Ra) in strata. Radon concentration in groundwater increases to reach an equilibrated value within about three weeks after infiltrating underground. The equilibrated concentration becomes an own value of the aquifer depending on the radium content, the grain size and porosity of aquifer. The characteristic makes it able to identify aquifers and sub basins. Since radon concentration in groundwater is 100 to 1000 times as high as that in surface water, groundwater and surface water interaction is quantitatively analyzed. A liquid scintillation counter was employed to measure radon concentration after extracting radon in water to toluene. We applied those advantage of radon-222 to various field investigations and discussed the applicability. It was really possible to analyze the groundwater flow. Monitoring radon concentration in pumped water, occurrences of squeeze and leakage from the different aquifer were detected. Main aquifer was easily determined from the vertical distribution of radon concentration in bore hole. In the injection test using surface water, the spread of injected water was confirmed by the decrease of radon concentration in bore hole water. The radon method was useful to analyze the dam leakage, effluent seepage of groundwater in river, influent seepage of river water underground, and groundwater recharge with irrigation water through unsaturated zone. (author)

  16. Uncertainty analysis of a groundwater flow model in east-central Florida

    Science.gov (United States)

    Sepulveda, Nicasio; Doherty, John E.

    2014-01-01

    A groundwater flow model for east-central Florida has been developed to help water-resource managers assess the impact of increased groundwater withdrawals from the Floridan aquifer system on heads and spring flows originating from the Upper Floridan aquifer. The model provides a probabilistic description of predictions of interest to water-resource managers, given the uncertainty associated with system heterogeneity, the large number of input parameters, and a nonunique groundwater flow solution. The uncertainty associated with these predictions can then be considered in decisions with which the model has been designed to assist. The “Null Space Monte Carlo” method is a stochastic probabilistic approach used to generate a suite of several hundred parameter field realizations, each maintaining the model in a calibrated state, and each considered to be hydrogeologically plausible. The results presented herein indicate that the model’s capacity to predict changes in heads or spring flows that originate from increased groundwater withdrawals is considerably greater than its capacity to predict the absolute magnitudes of heads or spring flows. Furthermore, the capacity of the model to make predictions that are similar in location and in type to those in the calibration dataset exceeds its capacity to make predictions of different types at different locations. The quantification of these outcomes allows defensible use of the modeling process in support of future water-resources decisions. The model allows the decision-making process to recognize the uncertainties, and the spatial/temporal variability of uncertainties that are associated with predictions of future system behavior in a complex hydrogeological context.

  17. Research on fracture analysis, groundwater flow and sorption processes in fractured rocks

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dae Ha [Korea Institute of Geology Mining and Materials, Taejon (Korea)

    1998-12-01

    Due to increasing demand for numerous industrial facilities including nuclear power plants and waste repositories, the feasibility of rocks masses as sites for the facilities has been a geological issue of concern. Rock masses, in general, comprises systems of fractures which can provide pathways for groundwater flow and may also affect the stability of engineered structures. such properties of fractures stimulate a synthetic study on (1) analyses of fracture systems, and (2) characterization of groundwater flow and sorption processes in fractured rocks to establish a preliminary model for assessing suitable sites for industrial facilities. The analyses of fracture systems cover (1) reconstruction of the Cenozoic tectonic movements and estimation of frequency indices for the Holocene tectonic movements, (2) determination of distributions and block movements of the Quaternary marine terraces, (3) investigation of lithologic and geotechnical nature of study area, and (4) examination of the Cenozoic volcanic activities and determination of age of the dike swarms. Using data obtained from above mentioned analyses along with data related to earthquakes and active faults, probabilistic approach is performed to determine various potential hazards which may result from the Quaternary or the Holocene tectonic movements. In addition, stepwise and careful integration of various data obtained from field works and laboratory experiments are carried out to analyze groundwater flow in fractures rocks as follows; (1) investigation of geological feature of the site, (2) identification and characterization of fracture systems using core and televiewer logs, (3) determination of conductive fractures using electrical conductivity, temperature, and flow logs, (4) identification of hydraulic connections between fractures using televiewer logs with tracer tests within specific zones. The results obtained from these processes allow a qualitative interpretation of groundwater flow patterns

  18. Recharge source identification using isotope analysis and groundwater flow modeling for Puri city in India

    Science.gov (United States)

    Nayak, P. C.; Vijaya Kumar, S. V.; Rao, P. R. S.; Vijay, T.

    2017-11-01

    The holy city of Lord Jagannath is situated on the sea shore of the Bay of Bengal in Odisha state in India. Puri is a city of high religious importance and heritage value, details of the rituals, fairs, and festivals, and related aspects are covered extensively. It is found that water levels in two wells (Ganga and Yamuna) are declining and the causes are studied by undertaking modeling study of rainfall-recharge processes, surface water-groundwater interactions, and increasing demands due to urbanization at basin scale. Hydrochemical analysis of groundwater samples indicates that pH value is varying from 7 to 8.4 and electrical conductivity (EC) is found in between 238 and 2710 μmhos/cm. The EC values indicate that the shallow groundwater in Puri is not saline. Stable isotopic signatures of O-18, Deuterium indicate two different sources are active in the city area. In most of the handpumps, water recharged by the surface water sources. From the current investigation, it is evident that in a few handpumps and most of the dug-wells, isotopic signatures of water samples resembles with local precipitation. The groundwater recharge is taking place from the north-southern direction. Visual MODFLOW has been used for studying groundwater aspects and different scenarios have been developed. It is suggested to maintain water level in Samang Lake to restore depletion in groundwater level in two wells.

  19. Estimation of the sources and flow system of groundwater in Fuji-Gotenba area by stable isotopic analysis and groundwater flow simulation

    International Nuclear Information System (INIS)

    Tomiyama, Shingo; Miyaike, Shusaku; Ii, Hiroyuki; Hattori, Ryota; Ito, Yuji

    2009-01-01

    Understanding the source and chemical character of the groundwater provides an important strategy for the quality management of mineral water and food materials. In order to identify a source and the flow paths of groundwater used for mineral water, the water quality and stable isotopes of hydrogen and oxygen of well water in Gotenba city were studied. The electrical conductivity and chemical character of sampled water are similar to those of well water and spring water discharged elsewhere around Mt. Fuji. The hydrogen and oxygen isotopic ratios of water samples indicate their origin to be solely meteoric and the oxygen isotopic ratios suggest that the groundwater mainly originated from the mountain-side of Mt. Fuji at altitudes of from 1500 m to 2300 m. A subsequent simulation of groundwater showed that the distribution of the total head and the Darcy velocity are down streamlines from mountain-sides toward the study area in Gotenba city. The altitudes of discharge obtained by the simulation are above 2000 m, and these correspond well with altitudes estimated from δ 18 O values of the samples. (author)

  20. Novel patch modelling method for efficient simulation and prediction uncertainty analysis of multi-scale groundwater flow and transport processes

    Science.gov (United States)

    Sreekanth, J.; Moore, Catherine

    2018-04-01

    The application of global sensitivity and uncertainty analysis techniques to groundwater models of deep sedimentary basins are typically challenged by large computational burdens combined with associated numerical stability issues. The highly parameterized approaches required for exploring the predictive uncertainty associated with the heterogeneous hydraulic characteristics of multiple aquifers and aquitards in these sedimentary basins exacerbate these issues. A novel Patch Modelling Methodology is proposed for improving the computational feasibility of stochastic modelling analysis of large-scale and complex groundwater models. The method incorporates a nested groundwater modelling framework that enables efficient simulation of groundwater flow and transport across multiple spatial and temporal scales. The method also allows different processes to be simulated within different model scales. Existing nested model methodologies are extended by employing 'joining predictions' for extrapolating prediction-salient information from one model scale to the next. This establishes a feedback mechanism supporting the transfer of information from child models to parent models as well as parent models to child models in a computationally efficient manner. This feedback mechanism is simple and flexible and ensures that while the salient small scale features influencing larger scale prediction are transferred back to the larger scale, this does not require the live coupling of models. This method allows the modelling of multiple groundwater flow and transport processes using separate groundwater models that are built for the appropriate spatial and temporal scales, within a stochastic framework, while also removing the computational burden associated with live model coupling. The utility of the method is demonstrated by application to an actual large scale aquifer injection scheme in Australia.

  1. Stability analysis of rockmass using a hydrogeologic model of groundwater flow at an underground limestone mine in Korea

    Science.gov (United States)

    Baek, H.; Kim, D.; Kim, G.; Kim, D.; Cheong, S.

    2017-12-01

    The safety and environmental issues should be addressed for sustainable mining operations. One of the key factors is the groundwater flow into underground mine workings, which will affect the overall workability and efficiency of the mining operation. Prediction of the groundwater inflow requires a detailed knowledge of the geologic conditions, including the presence of major faults and other geologic structures at the mine site. The hydrologic boundaries and depth of the phreatic surface of the mine area, as well as other relevant properties of the rockmass, are also provided. The stability of underground structures, in terms of the maximum stresses and deformations within the rockmass, can be analyzed using either the total stress or the effective stress approaches. Both the dried and saturated conditions should be considered with appropriate safety factors, as the distribution of the water pressure within the rockmass resulted from the groundwater flow directly affects the stability. In some cases, the rockmass rating systems such as the RMR and Q-systems are also applied. Various numerical codes have been used to construct the hydrogeologic models of mine sites, and the MINEDW by Itasca is one of those groundwater flow model codes developed to simulate groundwater flow related to mining. In this study, with a 3D hydrogeologic model constructed using the MINEDW for an underground limestone mine, the rate of mine water inflow and the porewater pressure were estimated. The stability of mine pillars and adits was analyzed adopting the porewater pressure and effective stress developed in the rockmass. The results were also compared with those from other 2D stability analysis procedures.

  2. Site scale groundwater flow in Haestholmen

    Energy Technology Data Exchange (ETDEWEB)

    Loefman, J. [VTT Energy, Espoo (Finland)

    1999-05-01

    Groundwater flow modelling on the site scale has been an essential part of site investigation work carried out at different locations since 1986. The objective of the modelling has been to provide results that characterise the groundwater flow conditions deep in the bedrock. The main result quantities can be used for evaluation of the investigation sites and of the preconditions for safe final disposal - of spent nuclear fuel. This study represents the groundwater flow modelling at Haestholmen, and it comprises the transient flow analysis taking into account the effects of density variations and the repository as well as the post-glacial land uplift. The analysis is performed by means of numerical finite element simulation of coupled and transient groundwater flow and solute transport carried out up to 10000 years into the future. This work provides also the results for the site-specific data needs for the block scale groundwater flow modelling at Haestholmen. Conceptually the fractured bedrock is divided into hydraulic units: the planar fracture zones and the remaining part of the bedrock. The equivalent-continuum (EC) model is applied so that each hydraulic unit is treated as a homogeneous and isotropic continuum with representative average characteristics. All the fracture zones are modelled explicitly and represented by two-dimensional finite elements. A site-specific simulation model for groundwater flow and solute transport is developed on the basis of the latest hydrogeological and hydrogeochemical field investigations at Haestholmen. The present topography together with a mathematical model describing the land uplift at the Haestholmen area are employed as a boundary condition at the surface of the model. The overall flow pattern is mostly controlled by the local variations in the topography and by the highly transmissive fracture zones. Near the surface the flow spreads out to offshore and to the lower areas of topography in all directions away from

  3. Stochastic ground-water flow analysis FY-81 status report. Assessment of effectiveness of geologic isolation systems

    International Nuclear Information System (INIS)

    Kincaid, C.T.; Vail, L.W.; Devary, J.L.

    1983-07-01

    Research was conducted at Pacific Northwest Laboratory to develop a research computational package for the stochastic analysis of ground-water flow. Both unsteady and steady-state analysis were examined, and a steady-state research code was developed for the study of stochastic processes. This report describes the theoretical development of both unsteady and steady analyses, and presents the preliminary studies undertaken to verify and exercise the encoded algorithm. The stochastic analysis of ground-water flow is a promising new method which can supply more comprehensive analyses of the ground-water environment. The work reported herein provided experience in the methodology while producing a research-oriented stochastic analysis capability. Single-layer aquifers of horizontal extent were selected for this effort. Kriging has been employed to describe the uncertainty in field data. The resulting stochastic parameters enter the problem physics through boundary conditions and Darcy's equation. The mean and variance of the piezometric head are estimated by the stochastic analysis

  4. Regression modeling of ground-water flow

    Science.gov (United States)

    Cooley, R.L.; Naff, R.L.

    1985-01-01

    Nonlinear multiple regression methods are developed to model and analyze groundwater flow systems. Complete descriptions of regression methodology as applied to groundwater flow models allow scientists and engineers engaged in flow modeling to apply the methods to a wide range of problems. Organization of the text proceeds from an introduction that discusses the general topic of groundwater flow modeling, to a review of basic statistics necessary to properly apply regression techniques, and then to the main topic: exposition and use of linear and nonlinear regression to model groundwater flow. Statistical procedures are given to analyze and use the regression models. A number of exercises and answers are included to exercise the student on nearly all the methods that are presented for modeling and statistical analysis. Three computer programs implement the more complex methods. These three are a general two-dimensional, steady-state regression model for flow in an anisotropic, heterogeneous porous medium, a program to calculate a measure of model nonlinearity with respect to the regression parameters, and a program to analyze model errors in computed dependent variables such as hydraulic head. (USGS)

  5. A geostatistics-informed hierarchical sensitivity analysis method for complex groundwater flow and transport modeling: GEOSTATISTICAL SENSITIVITY ANALYSIS

    Energy Technology Data Exchange (ETDEWEB)

    Dai, Heng [Pacific Northwest National Laboratory, Richland Washington USA; Chen, Xingyuan [Pacific Northwest National Laboratory, Richland Washington USA; Ye, Ming [Department of Scientific Computing, Florida State University, Tallahassee Florida USA; Song, Xuehang [Pacific Northwest National Laboratory, Richland Washington USA; Zachara, John M. [Pacific Northwest National Laboratory, Richland Washington USA

    2017-05-01

    Sensitivity analysis is an important tool for quantifying uncertainty in the outputs of mathematical models, especially for complex systems with a high dimension of spatially correlated parameters. Variance-based global sensitivity analysis has gained popularity because it can quantify the relative contribution of uncertainty from different sources. However, its computational cost increases dramatically with the complexity of the considered model and the dimension of model parameters. In this study we developed a hierarchical sensitivity analysis method that (1) constructs an uncertainty hierarchy by analyzing the input uncertainty sources, and (2) accounts for the spatial correlation among parameters at each level of the hierarchy using geostatistical tools. The contribution of uncertainty source at each hierarchy level is measured by sensitivity indices calculated using the variance decomposition method. Using this methodology, we identified the most important uncertainty source for a dynamic groundwater flow and solute transport in model at the Department of Energy (DOE) Hanford site. The results indicate that boundary conditions and permeability field contribute the most uncertainty to the simulated head field and tracer plume, respectively. The relative contribution from each source varied spatially and temporally as driven by the dynamic interaction between groundwater and river water at the site. By using a geostatistical approach to reduce the number of realizations needed for the sensitivity analysis, the computational cost of implementing the developed method was reduced to a practically manageable level. The developed sensitivity analysis method is generally applicable to a wide range of hydrologic and environmental problems that deal with high-dimensional spatially-distributed parameters.

  6. Analysis of the Shallow Groundwater Flow System at Fire Island National Seashore, Suffolk County, New York

    Science.gov (United States)

    Schubert, Christopher E.

    2010-01-01

    . A variable-density model of the shallow aquifer system and adjacent marine surface waters was developed to simulate groundwater flow patterns and rates. Nitrogen loads from the shallow aquifer system were calculated from representative total nitrogen (TN) concentrations and simulated groundwater discharges to back-barrier estuaries and the ocean. The model simulates groundwater directions, velocities, and discharge rates under 2005 mean annual conditions. Groundwater budgets were developed for recharge areas of similar land use that contribute freshwater to back-barrier estuaries, the ocean, and subsea-discharge zones. Total freshwater discharge from the shallow aquifer system is about 43,500 cubic meters per day (m3/d) (79.8 percent) to back-barrier estuaries and about 10,200 m3/d (18.7 percent) to the ocean; about 836 m3/d (1.5 percent) may exit the system as subsea underflow. The total contribution of fresh groundwater to shoreline discharge zones amounts to about 53,700 m3/d (98.5 percent). The median age of freshwater discharged to back-barrier estuaries and the ocean was 3.4 years, and the 95th-percentile age was 20 years. The TN concentrations and loads under 2005 mean annual conditions for areas that contribute fresh groundwater to back-barrier estuaries and the ocean were calculated for the principal land uses on Fire Island. The overall TN load from the shallow aquifer system to shoreline discharge zones is about 16,200 kilograms per year (kg/yr) (82.2 percent) to back-barrier estuaries and about 3,500 kg/yr (17.8 percent) to the ocean. The overall TN load to marine surface waters amounts to about 19,700 kg/yr-roughly 6 percent of the annual TN load from shallow groundwater entering the South Shore Estuary Reserve (SSER) from the Suffolk County mainland, which is about 345,000 kg/yr. In contrast to the TN load from shallow groundwater for the SSER watershed, which annually yields about 353 kilograms per square kilometer (kg/km2), the overall TN loa

  7. Groundwater flow code verification ``benchmarking`` activity (COVE-2A): Analysis of participants` work

    Energy Technology Data Exchange (ETDEWEB)

    Dykhuizen, R.C.; Barnard, R.W.

    1992-02-01

    The Nuclear Waste Repository Technology Department at Sandia National Laboratories (SNL) is investigating the suitability of Yucca Mountain as a potential site for underground burial of nuclear wastes. One element of the investigations is to assess the potential long-term effects of groundwater flow on the integrity of a potential repository. A number of computer codes are being used to model groundwater flow through geologic media in which the potential repository would be located. These codes compute numerical solutions for problems that are usually analytically intractable. Consequently, independent confirmation of the correctness of the solution is often not possible. Code verification is a process that permits the determination of the numerical accuracy of codes by comparing the results of several numerical solutions for the same problem. The international nuclear waste research community uses benchmarking for intercomparisons that partially satisfy the Nuclear Regulatory Commission (NRC) definition of code verification. This report presents the results from the COVE-2A (Code Verification) project, which is a subset of the COVE project.

  8. Groundwater flow code verification ''benchmarking'' activity (COVE-2A): Analysis of participants' work

    International Nuclear Information System (INIS)

    Dykhuizen, R.C.; Barnard, R.W.

    1992-02-01

    The Nuclear Waste Repository Technology Department at Sandia National Laboratories (SNL) is investigating the suitability of Yucca Mountain as a potential site for underground burial of nuclear wastes. One element of the investigations is to assess the potential long-term effects of groundwater flow on the integrity of a potential repository. A number of computer codes are being used to model groundwater flow through geologic media in which the potential repository would be located. These codes compute numerical solutions for problems that are usually analytically intractable. Consequently, independent confirmation of the correctness of the solution is often not possible. Code verification is a process that permits the determination of the numerical accuracy of codes by comparing the results of several numerical solutions for the same problem. The international nuclear waste research community uses benchmarking for intercomparisons that partially satisfy the Nuclear Regulatory Commission (NRC) definition of code verification. This report presents the results from the COVE-2A (Code Verification) project, which is a subset of the COVE project

  9. Modeling groundwater flow and quality

    Science.gov (United States)

    Konikow, Leonard F.; Glynn, Pierre D.; Selinus, Olle

    2013-01-01

    In most areas, rocks in the subsurface are saturated with water at relatively shallow depths. The top of the saturated zone—the water table—typically occurs anywhere from just below land surface to hundreds of feet below the land surface. Groundwater generally fills all pore spaces below the water table and is part of a continuous dynamic flow system, in which the fluid is moving at velocities ranging from feet per millennia to feet per day (Fig. 33.1). While the water is in close contact with the surfaces of various minerals in the rock material, geochemical interactions between the water and the rock can affect the chemical quality of the water, including pH, dissolved solids composition, and trace-elements content. Thus, flowing groundwater is a major mechanism for the transport of chemicals from buried rocks to the accessible environment, as well as a major pathway from rocks to human exposure and consumption. Because the mineral composition of rocks is highly variable, as is the solubility of various minerals, the human-health effects of groundwater consumption will be highly variable.

  10. POSIVA groundwater flow measuring techniques

    International Nuclear Information System (INIS)

    Oehberg, A.; Rouhiainen, P.

    2000-08-01

    Posiva Oy has carried out site characterisation for the final disposal of spent nuclear fuel in Finland since 1987. To meet the demanding needs to measure the hydraulic parameters in bedrock Posiva launched development of new flowmeter techniques including measuring methods and equipment in co-operation with PRG-Tec Oy. The techniques have been tested and used in the ongoing site investigations in Finland, in the underground Hard Rock Laboratory (HRL) at Aespoe in Sweden and in URL in Canada. The new methods are called difference flow and transverse flow methods. The difference flow method includes two modes, normal and detailed flow logging methods. In the normal mode the flow rate measurement is based on thermal pulse and thermal dilution methods, in the detailed logging mode only on thermal dilution method. The measuring ranges for flow rate with thermal pulse and dilution methods are 0.1-10 ml/min and 2-5000 ml/min, respectively. The difference flow method(normal mode) for small flows (0.1-10 ml/min) is based on measuring the pulse transit time and direction of a thermal pulse in the sensor. For high flows (2-5000 ml/min) the method is based on thermal dilution rate of a sensor. Direction is measured with monitoring thermistors. Inflow or outflow in the test interval is created due to natural or by pumping induced differences between heads in the borehole water and groundwater around the borehole. The single point resistance (and the temperature of borehole water) measurement is carried out simultaneously with the difference flow measurements, both in normal and detailed flow logging modes, while the tool is moving. The result is utilised for checking the exact depth of the tool. As the result a continuous log is obtained from which single fractures can be detected. The transverse flowmeter is able to measure the groundwater flow across a borehole. A special packer system guides the flow through the flow sensors. Four inflatable seals between conventional

  11. Development of one-dimensional computational fluid dynamics code 'GFLOW' for groundwater flow and contaminant transport analysis

    International Nuclear Information System (INIS)

    Rahatgaonkar, P. S.; Datta, D.; Malhotra, P. K.; Ghadge, S. G.

    2012-01-01

    Prediction of groundwater movement and contaminant transport in soil is an important problem in many branches of science and engineering. This includes groundwater hydrology, environmental engineering, soil science, agricultural engineering and also nuclear engineering. Specifically, in nuclear engineering it is applicable in the design of spent fuel storage pools and waste management sites in the nuclear power plants. Ground water modeling involves the simulation of flow and contaminant transport by groundwater flow. In the context of contaminated soil and groundwater system, numerical simulations are typically used to demonstrate compliance with regulatory standard. A one-dimensional Computational Fluid Dynamics code GFLOW had been developed based on the Finite Difference Method for simulating groundwater flow and contaminant transport through saturated and unsaturated soil. The code is validated with the analytical model and the benchmarking cases available in the literature. (authors)

  12. Analysis of groundwater flow and stream depletion in L-shaped fluvial aquifers

    Directory of Open Access Journals (Sweden)

    C.-C. Lin

    2018-04-01

    Full Text Available Understanding the head distribution in aquifers is crucial for the evaluation of groundwater resources. This article develops a model for describing flow induced by pumping in an L-shaped fluvial aquifer bounded by impermeable bedrocks and two nearly fully penetrating streams. A similar scenario for numerical studies was reported in Kihm et al. (2007. The water level of the streams is assumed to be linearly varying with distance. The aquifer is divided into two subregions and the continuity conditions of the hydraulic head and flux are imposed at the interface of the subregions. The steady-state solution describing the head distribution for the model without pumping is first developed by the method of separation of variables. The transient solution for the head distribution induced by pumping is then derived based on the steady-state solution as initial condition and the methods of finite Fourier transform and Laplace transform. Moreover, the solution for stream depletion rate (SDR from each of the two streams is also developed based on the head solution and Darcy's law. Both head and SDR solutions in the real time domain are obtained by a numerical inversion scheme called the Stehfest algorithm. The software MODFLOW is chosen to compare with the proposed head solution for the L-shaped aquifer. The steady-state and transient head distributions within the L-shaped aquifer predicted by the present solution are compared with the numerical simulations and measurement data presented in Kihm et al. (2007.

  13. Site scale groundwater flow in Olkiluoto

    Energy Technology Data Exchange (ETDEWEB)

    Loefman, J. [VTT Energy, Espoo (Finland)

    1999-03-01

    Groundwater flow modelling on the site scale has been an essential part of site investigation work carried out at different locations since 1986. The objective of the modelling has been to provide results that characterise the groundwater flow conditions deep in the bedrock. The main result quantities can be used for evaluation of the investigation sites and of the preconditions for safe final disposal of spent nuclear fuel. This study represents the latest modelling effort at Olkiluoto (Finland), and it comprises the transient flow analysis taking into account the effects of density variations and the repository as well as the post-glacial land uplift. The analysis is performed by means of numerical finite element simulation of coupled and transient groundwater flow and solute transport carried out up to 10000 years into the future. This work provides also the results for the site-specific data needs for the block scale groundwater flow modelling at Olkiluoto. Conceptually the fractured bedrock is divided into hydraulic units: the planar fracture zones and the remaining part of the bedrock. The equivalent-continuum (EC) model is applied so that each hydraulic unit is treated as a homogeneous and isotropic continuum with representative average characteristics. All the fracture zones are modelled explicitly and represented by two-dimensional finite elements. A site-specific simulation model for groundwater flow and solute transport is developed on the basis of the latest hydrogeological and hydrogeochemical field investigations at Olkiluoto. The present groundwater table and topography together with a mathematical model describing the land uplift at the Olkiluoto area are employed as a boundary condition at the surface of the model. The overall flow pattern is mostly controlled by the local variations in the topography. Below the island of Olkiluoto the flow direction is mostly downwards, while near the shoreline and below the sea water flows horizontally and

  14. A site scale analysis of groundwater flow and salinity distribution in the Aespoe area

    International Nuclear Information System (INIS)

    Svensson, Urban

    1997-10-01

    The objective of the study is to develop, calibrate and apply a numerical simulation model of the Aespoe area. An area of 1.8 x 1.8 km 2 , centred around the Aespoe Hard Rock Laboratory (HRL), gives the horizontal extent of the model. In the vertical direction the model follows the topography at the upper boundary and has a lower boundary at 1000 metres below sea level. The model is based on a mathematical model that includes equations for the Darcy velocities, mass conservation and salinity distribution. Gravitational effects are thus fully accounted for. A regional groundwater model was used to generate boundary conditions for vertical and bottom boundaries. Transmissivities of fracture zones and conductivities for the rock in between, as used in the model, are based on field data. An extensive calibration of the model is carried out, using data for natural conditions (i.e. prior to the construction of the Aespoe HRL), drawdowns from a pump test and data collected during the excavation of the tunnel. A satisfactory agreement with field data is obtained by the calibration. Main results from the model include vertical and horizontal sections of flow, salinity and hydraulic head distributions for natural conditions and for completed tunnel. A sensitivity study, where boundary conditions and material properties are modified, is also carried out. The model is also used to describe some characteristic features of the site like infiltration rates, flux statistics at a depth of 450 metres, salinity of inflows to the tunnel and flow and salinity distributions in fracture zones. The general conclusion of the study is that the model developed can simulate the conditions at Aespoe, both natural and with Aespoe HRL present, in a realistic manner

  15. Stochastic simulation of regional groundwater flow in Beishan area

    International Nuclear Information System (INIS)

    Dong Yanhui; Li Guomin

    2010-01-01

    Because of the hydrogeological complexity, traditional thinking of aquifer characteristics is not appropriate for groundwater system in Beishan area. Uncertainty analysis of groundwater models is needed to examine the hydrologic effects of spatial heterogeneity. In this study, fast Fourier transform spectral method (FFTS) was used to generate the random horizontal permeability parameters. Depth decay and vertical anisotropy of hydraulic conductivity were included to build random permeability models. Based on high-performance computers, hundreds of groundwater flow models were simulated. Through stochastic simulations, the effect of heterogeneity to groundwater flow pattern was analyzed. (authors)

  16. A laboratory scale analysis of groundwater flow and salinity distribution in the Aespoe area

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Urban [Computer-aided Fluid Engineering AB, Norrkoeping (Sweden)

    1999-12-01

    This report concerns a study which was conducted for SKB. The conclusions and viewpoints presented in the report are those of the author(s) and do not necessarily coincide with those of the client. The objective of the study is to develop, calibrate and apply a numerical simulation model of the Aespoe Hard Rock Laboratory (HRL). An area of 800 x 600 centred around the HRL, gives the horizontal extent of the model. In the vertical direction the model covers the depth interval from 200 to 560 metres. The model is based on a mathematical model that includes equations for the Darcy velocities, mass conservation and salinity distribution. Gravitational effects are thus fully accounted for. A site scale groundwater model was used to generate boundary conditions for all boundaries. Transmissivities of major fracture zones are based on field data. Fractures and fracture zones with a length scale between 5 and 320 metres are accounted for by a novel method that is based on a discrete fracture network. A small background conductivity is added to account for fractures smaller than the grid size, which is metres. A calibration of the model is carried out, using field data from the Aespoe HRL. A satisfactory agreement with field data is obtained. Main results from the model include vertical and horizontal sections of flow, salinity and hydraulic head distributions for completed tunnel. A sensitivity study, where the properties of the conductivity field are modified, is also carried out. The general conclusion of the study is that the model developed can simulate the conditions at the Aespoe HRL in a realistic manner.

  17. UNCERT: geostatistics, uncertainty analysis and visualization software applied to groundwater flow and contaminant transport modeling

    International Nuclear Information System (INIS)

    Wingle, W.L.; Poeter, E.P.; McKenna, S.A.

    1999-01-01

    UNCERT is a 2D and 3D geostatistics, uncertainty analysis and visualization software package applied to ground water flow and contaminant transport modeling. It is a collection of modules that provides tools for linear regression, univariate statistics, semivariogram analysis, inverse-distance gridding, trend-surface analysis, simple and ordinary kriging and discrete conditional indicator simulation. Graphical user interfaces for MODFLOW and MT3D, ground water flow and contaminant transport models, are provided for streamlined data input and result analysis. Visualization tools are included for displaying data input and output. These include, but are not limited to, 2D and 3D scatter plots, histograms, box and whisker plots, 2D contour maps, surface renderings of 2D gridded data and 3D views of gridded data. By design, UNCERT's graphical user interface and visualization tools facilitate model design and analysis. There are few built in restrictions on data set sizes and each module (with two exceptions) can be run in either graphical or batch mode. UNCERT is in the public domain and is available from the World Wide Web with complete on-line and printable (PDF) documentation. UNCERT is written in ANSI-C with a small amount of FORTRAN77, for UNIX workstations running X-Windows and Motif (or Lesstif). This article discusses the features of each module and demonstrates how they can be used individually and in combination. The tools are applicable to a wide range of fields and are currently used by researchers in the ground water, mining, mathematics, chemistry and geophysics, to name a few disciplines. (Copyright (c) 1999 Elsevier Science B.V., Amsterdam. All rights reserved.)

  18. Research on flow characteristics of deep groundwater by environmental isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Shimada, Jun; Miyaoka, Kunihide [Tsukuba Univ., Ibaraki (Japan); Sakurai, Hideyuki; Senoo, Muneaki; Kumata, Masahiro; Mukai, Masayuki; Watanabe, Kazuo; Ouchi, Misao

    1996-01-01

    In this research, as the technique for grasping the behavior of groundwater in deep rock bed which is important as the factor of disturbing the natural barrier in the formation disposal of high level radioactive waste, the method of utilizing the environmental isotopes contained in groundwater as natural tracer was taken up, and by setting up the concrete field of investigation, through the forecast of flow by the two or three dimensional groundwater flow analysis using a computer, the planning and execution of water sampling, the analysis of various environmental isotopes, the interpretation based on those results of measurement and so on, the effectiveness of the investigation technique used was verified, and the real state of the behavior of deep groundwater in the district being studied was clarified. In this research, Imaichi alluvial fan located in northern Kanto plain was taken as the object. In fiscal year 1996, three-dimensional steady state groundwater flow simulation was carried out based on the data related to shallow groundwater and surface water systems, and the places where active groundwater flow is expected were selected, and boring will be carried out there. The analysis model and the results are reported. (K.I.)

  19. Groundwater flow modelling of Yamuna–Krishni interstream, a part ...

    Indian Academy of Sciences (India)

    Keeping this in mind groundwater flow modelling was attempted to simulate the behaviour of the flow system and evaluate the water balance. The groundwater flow modelling was carried ... Long term groundwater level trends show an average decline of 0.88m/year (Umar 2008). Groundwater serves as the main source of ...

  20. Stepwise hydrogeological modeling and groundwater flow analysis on site scale (The former part of the step 3)

    International Nuclear Information System (INIS)

    Onoe, Hironori; Saegusa, Hiromitsu; Endo, Yoshinobu

    2005-07-01

    One of the main goals of the Mizunami Underground Research Laboratory Project is to establish comprehensive techniques for investigation, analysis, and assessment of the deep geological environment. To achieve this goal, a variety of investigations are being conducted using an iterative approach. In this study, hydrogeological modeling and groundwater flow analyses have been carried out using the data from surface-based investigations at the former part of Step 3 (deep borehole investigations without vertical seismic profiling investigations), in order to synthesize the investigation results, to evaluate the uncertainty of the hydrogeological model, and to specify items for further investigation. The results of this study are summarized as follows: 1) The uncertainty of hydrogeological model of the site scale is decreased as stepwise research; 2) Borehole investigations combined with hydraulic monitoring are useful for decreasing the uncertainty of hydrogeological model; The main items specified for further investigations are summarized as follows: 1) Trend, length, and hydraulic parameters of faults confirmed in the MIU construction site; 2) Shape of boundary of geological layer, and hydraulic parameters of rock; 3) Hydraulic head distribution of deep underground. (author)

  1. Numerical simulation of groundwater flow in LILW Repository site:I. Groundwater flow modeling

    Energy Technology Data Exchange (ETDEWEB)

    Park, Koung Woo; Ji, Sung Hoon; Kim, Chun Soo; Kim, Kyoung Su [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of); Kim, Ji Yeon [Korea Hydro and Nuclear Power Co. Ltd., Seoul (Korea, Republic of)

    2008-12-15

    Based on the site characterization works in a low and intermediate level waste (LILW) repository site, the numerical simulations for groundwater flow were carried out in order to understand the groundwater flow system of repository site. To accomplish the groundwater flow modeling in the repository site, the discrete fracture network (DFN) model was constructed using the characteristics of fracture zones and background fractures. At result, the total 10 different hydraulic conductivity(K) fields were obtained from DFN model stochastically and K distributions of constructed mesh were inputted into the 10 cases of groundwater flow simulations in FEFLOW. From the total 10 numerical simulation results, the simulated groundwater levels were strongly governed by topography and the groundwater fluxes were governed by locally existed high permeable fracture zones in repository depth. Especially, the groundwater table was predicted to have several tens meters below the groundwater table compared with the undisturbed condition around disposal silo after construction of underground facilities. After closure of disposal facilities, the groundwater level would be almost recovered within 1 year and have a tendency to keep a steady state of groundwater level in 2 year.

  2. Validation Analysis of the Groundwater Flow and Transport Model of the Central Nevada Test Area

    Energy Technology Data Exchange (ETDEWEB)

    A. Hassan; J. Chapman; H. Bekhit; B. Lyles; K. Pohlmann

    2006-09-30

    The Central Nevada Test Area (CNTA) is a U.S. Department of Energy (DOE) site undergoing environmental restoration. The CNTA is located about 95 km northeast of Tonopah, Nevada, and 175 km southwest of Ely, Nevada (Figure 1.1). It was the site of the Faultless underground nuclear test conducted by the U.S. Atomic Energy Commission (DOE's predecessor agency) in January 1968. The purposes of this test were to gauge the seismic effects of a relatively large, high-yield detonation completed in Hot Creek Valley (outside the Nevada Test Site [NTS]) and to determine the suitability of the site for future large detonations. The yield of the Faultless underground nuclear test was between 200 kilotons and 1 megaton (DOE, 2000). A three-dimensional flow and transport model was created for the CNTA site (Pohlmann et al., 1999) and determined acceptable by DOE and the Nevada Division of Environmental Protection (NDEP) for predicting contaminant boundaries for the site.

  3. TYBO/BENHAM: Model Analysis of Groundwater Flow and Radionuclide Migration from Underground Nuclear Tests in Southwestern Pahute Mesa, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Andrew Wolfsberg; Lee Glascoe; Guoping Lu; Alyssa Olson; Peter Lichtner; Maureen McGraw; Terry Cherry; Guy Roemer

    2002-09-01

    Recent field studies have led to the discovery of trace quantities of plutonium originating from the BENHAM underground nuclear test in two groundwater observation wells on Pahute Mesa at the Nevada Test Site. These observation wells are located 1.3 km from the BENHAM underground nuclear test and approximately 300 m from the TYBO underground nuclear test. In addition to plutonium, several other conservative (e.g. tritium) and reactive (e.g. cesium) radionuclides were found in both observation wells. The highest radionuclide concentrations were found in a well sampling a welded tuff aquifer more than 500m above the BENHAM emplacement depth. These measurements have prompted additional investigations to ascertain the mechanisms, processes, and conditions affecting subsurface radionuclide transport in Pahute Mesa groundwater. This report describes an integrated modeling approach used to simulate groundwater flow, radionuclide source release, and radionuclide transport near the BENHAM and TYBO underground nuclear tests on Pahute Mesa. The components of the model include a flow model at a scale large enough to encompass many wells for calibration, a source-term model capable of predicting radionuclide releases to aquifers following complex processes associated with nonisothermal flow and glass dissolution, and site-scale transport models that consider migration of solutes and colloids in fractured volcanic rock. Although multiple modeling components contribute to the methodology presented in this report, they are coupled and yield results consistent with laboratory and field observations. Additionally, sensitivity analyses are conducted to provide insight into the relative importance of uncertainty ranges in the transport parameters.

  4. Geomorphic aspects of groundwater flow

    Science.gov (United States)

    LaFleur, Robert G.

    The many roles that groundwater plays in landscape evolution are becoming more widely appreciated. In this overview, three major categories of groundwater processes and resulting landforms are considered: (1) Dissolution creates various karst geometries, mainly in carbonate rocks, in response to conditions of recharge, geologic setting, lithology, and groundwater circulation. Denudation and cave formation rates can be estimated from kinetic and hydraulic parameters. (2) Groundwater weathering generates regoliths of residual alteration products at weathering fronts, and subsequent exhumation exposes corestones, flared slopes, balanced rocks, domed inselbergs, and etchplains of regional importance. Groundwater relocation of dissolved salts creates duricrusts of various compositions, which become landforms. (3) Soil and rock erosion by groundwater processes include piping, seepage erosion, and sapping, important agents in slope retreat and headward gully migration. Thresholds and limits are important in many chemical and mechanical groundwater actions. A quantitative, morphometric approach to groundwater landforms and processes is exemplified by selected studies in carbonate and clastic terrains of ancient and recent origins. Résumé Les rôles variés joués par les eaux souterraines dans l'évolution des paysages deviennent nettement mieux connus. La revue faite ici prend en considération trois grandes catégories de processus liés aux eaux souterraines et les formes associées: (1) La dissolution crée des formes karstiques variées, surtout dans les roches carbonatées, en fonction des conditions d'alimentation, du cadre géologique, de la lithologie et de la circulation des eaux souterraines. Les taux d'érosion et de formation des grottes peuvent être estimés à partir de paramètres cinétiques et hydrauliques. (2) L'érosion par les eaux souterraines donne naissance à des régolites, résidus d'altération sur des fronts d'altération, et l'exhumation r

  5. Flow calculations for Yucca Mountain groundwater travel time (GWTT-95)

    Energy Technology Data Exchange (ETDEWEB)

    Altman, S.J.; Arnold, B.W.; Barnard, R.W.; Barr, G.E.; Ho, C.K.; McKenna, S.A.; Eaton, R.R.

    1996-09-01

    In 1983, high-level radioactive waste repository performance requirements related to groundwater travel time were defined by NRC subsystem regulation 10 CFR 60.113. Although DOE is not presently attempting to demonstrate compliance with that regulation, understanding of the prevalence of fast paths in the groundwater flow system remains a critical element of any safety analyses for a potential repository system at Yucca Mountain, Nevada. Therefore, this analysis was performed to allow comparison of fast-path flow against the criteria set forth in the regulation. Models developed to describe the conditions for initiation, propagation, and sustainability of rapid groundwater movement in both the unsaturated and saturated zones will form part of the technical basis for total- system analyses to assess site viability and site licensability. One of the most significant findings is that the fastest travel times in both unsaturated and saturated zones are in the southern portion of the potential repository, so it is recommended that site characterization studies concentrate on this area. Results support the assumptions regarding the importance of an appropriate conceptual model of groundwater flow and the incorporation of heterogeneous material properties into the analyses. Groundwater travel times are sensitive to variation/uncertainty in hydrologic parameters and in infiltration flux at upper boundary of the problem domain. Simulated travel times are also sensitive to poorly constrained parameters of the interaction between flow in fractures and in the matrix.

  6. Pore pressure measurement plan of near field rock used on three dimensional groundwater flow analysis in demonstration test of cavern type disposal facility

    International Nuclear Information System (INIS)

    Onuma, Kazuhiro; Terada, Kenji; Matsumura, Katsuhide; Koyama, Toshihiro; Yajima, Kazuaki

    2008-01-01

    Demonstration test of underground cavern type disposal facilities is planed though carrying out construction of full scale engineering barrier system which simulated in the underground space in full scale and under actual environment. This test consists of three part, these are construction test, performance test and measurement test. Behavior of near field rock mass is measured about hydrological behavior under and after construction to evaluate effect at test facility. To make plan of pore pressure measurement, three dimensional groundwater flow analysis has been carried out. Based on comparison of analysis before and after test, detail plan has been studied. (author)

  7. Heat and Groundwater Flow in the San Gabriel Mountains, California

    Science.gov (United States)

    Newman, A. A.; Becker, M.; Laton, W. R., Jr.

    2017-12-01

    Groundwater flow paths in mountainous terrain often vary widely in both time and space. Such systems remain difficult to characterize due to fracture-dominated flow paths, high topographic relief, and sparse hydrologic data. We develop a hydrogeologic conceptual model of the Western San Gabriel Mountains in Southern California based on geophysical, thermal, and hydraulic head data. Boreholes are located along the San Gabriel Fault Zone (SGFZ) and cover a wide range of elevations to capture the heterogeneity of the hydrogeologic system. Long term (2016-2017) monitoring of temperature and hydraulic head was carried out in four shallow (300-600m depth) boreholes within the study area using fiber-optic distributed temperature sensing (DTS). Borehole temperature profiles were used to assess the regional groundwater flow system and local flows in fractures intersecting the borehole. DTS temperature profiles were compared with available borehole geophysical logs and head measurements collected with grouted vibrating wire pressure transducers (VWPT). Spatial and temporal variations in borehole temperature profiles suggest that advective heat transfer due to fluid flow affected the subsurface thermal regime. Thermal evidence of groundwater recharge and/or discharge and flow through discrete fractures was found in all four boreholes. Analysis of temporal changes to the flow system in response to seasonal and drilling-induced hydraulic forcing was useful in reducing ambiguities in noisy datasets and estimating interborehole relationships. Acoustic televiewer logs indicate fractures were primarily concentrated in densely fractured intervals, and only a minor decrease of fracture density was observed with depth. Anomalously high hydraulic gradients across the SGFZ suggest that the feature is a potential barrier to lateral flow. However, transient thermal anomalies consistent with groundwater flow within the SGFZ indicate this feature may be a potential conduit to vertical flow

  8. A Method to Evaluate Groundwater flow system under the Seabed

    Science.gov (United States)

    Kohara, N.; Marui, A.

    2011-12-01

    / fresh water interface (position of the submarine groundwater discharge) may appear on the seafloor. Moreover, neither the salinity concentration nor the groundwater age depends on depth. It is thought that it is because that the groundwater forms the complex flow situation through the change in a long-term groundwater flow system. The technology to understand the coastal groundwater flow consists of remote sensing, geographical features analysis, surface of the earth investigation, geophysical exploration, drilling survey, and indoor examination and the measurement. Integration of each technology is needed to interpret groundwater flow system because the one is to catch the local groundwater flow in the time series and another one is to catch the long-term and regional groundwater flow in the general situation. The purpose of this study is to review the previous research of coastal groundwater flow, and to integrate an applicable evaluation approach to understand this mechanism. In this presentation, the review of the research and case study using numerical simulation are introduced.

  9. Groundwater flow and sorption processes in fractured rocks (I)

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Won Young; Woo, Nam Chul; Yum, Byoung Woo; Choi, Young Sub; Chae, Byoung Kon; Kim, Jung Yul; Kim, Yoo Sung; Hyun, Hye Ja; Lee, Kil Yong; Lee, Seung Gu; Youn, Youn Yul; Choon, Sang Ki [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

    1996-12-01

    This study is objected to characterize groundwater flow and sorption processes of the contaminants (ground-water solutes) along the fractured crystalline rocks in Korea. Considering that crystalline rock mass is an essential condition for using underground space cannot be overemphasized the significance of the characterizing fractured crystalline rocks. the behavior of the groundwater contaminants is studied in related to the subsurface structure, and eventually a quantitative technique will be developed to evaluate the impacts of the contaminants on the subsurface environments. The study has been carried at the Samkwang mine area in the Chung-Nam Province. The site has Pre-Cambrian crystalline gneiss as a bedrock and the groundwater flow system through the bedrock fractures seemed to be understandable with the study on the subsurface geologic structure through the mining tunnels. Borehole tests included core logging, televiewer logging, constant pressure fixed interval length tests and tracer tests. The results is summarized as follows; 1) To determine the hydraulic parameters of the fractured rock, the transient flow analysis produce better results than the steady - state flow analysis. 2) Based on the relationship between fracture distribution and transmissivities measured, the shallow part of the system could be considered as a porous and continuous medium due to the well developed fractures and weathering. However, the deeper part shows flow characteristics of the fracture dominant system, satisfying the assumptions of the Cubic law. 3) Transmissivities from the FIL test were averaged to be 6.12 x 10{sup -7}{sub m}{sup 2}{sub /s}. 4) Tracer tests result indicates groundwater flow in the study area is controlled by the connection, extension and geometry of fractures in the bedrock. 5) Hydraulic conductivity of the tracer-test interval was in maximum of 7.2 x 10{sup -6}{sub m/sec}, and the effective porosity of 1.8 %. 6) Composition of the groundwater varies

  10. Validation of groundwater flow model using the change of groundwater flow caused by the construction of AESPOE hard rock laboratory

    International Nuclear Information System (INIS)

    Hasegawa, Takuma; Tanaka, Yasuharu

    2004-01-01

    A numerical model based on results during pre-investigation phases was applied to the groundwater flow change caused by the construction of AEspoe HRL. The drawdowns and chloride concentration during tunnel construction were simulated to validate the numerical model. The groundwater flow was induced by inflow from the Baltic Sea to the tunnel through the hydraulic conductor domain (HCD). The time series of tunnel progress and inflow, boundaries of the Baltic Sea, transmissivity and geometry of HCD are therefore important in representing the groundwater flow. The numerical model roughly represented the groundwater flow during tunnel construction. These simulations were effective in validating the numerical model for groundwater flow and solute transport. (author)

  11. Bias in groundwater samples caused by wellbore flow

    Science.gov (United States)

    Reilly, Thomas E.; Franke, O. Lehn; Bennett, Gordon D.

    1989-01-01

    Proper design of physical installations and sampling procedures for groundwater monitoring networks is critical for the detection and analysis of possible contaminants. Monitoring networks associated with known contaminant sources sometimes include an array of monitoring wells with long well screens. The purpose of this paper is: (a) to report the results of a numerical experiment indicating that significant borehole flow can occur within long well screens installed in homogeneous aquifers with very small head differences in the aquifer (less than 0.01 feet between the top and bottom of the screen); (b) to demonstrate that contaminant monitoring wells with long screens may completely fail to fulfill their purpose in many groundwater environments.

  12. Ambient groundwater flow diminishes nitrogen cycling in streams

    Science.gov (United States)

    Azizian, M.; Grant, S. B.; Rippy, M.; Detwiler, R. L.; Boano, F.; Cook, P. L. M.

    2017-12-01

    Modeling and experimental studies demonstrate that ambient groundwater reduces hyporheic exchange, but the implications of this observation for stream N-cycling is not yet clear. We utilized a simple process-based model (the Pumping and Streamline Segregation or PASS model) to evaluate N- cycling over two scales of hyporheic exchange (fluvial ripples and riffle-pool sequences), ten ambient groundwater and stream flow scenarios (five gaining and losing conditions and two stream discharges), and three biogeochemical settings (identified based on a principal component analysis of previously published measurements in streams throughout the United States). Model-data comparisons indicate that our model provides realistic estimates for direct denitrification of stream nitrate, but overpredicts nitrification and coupled nitrification-denitrification. Riffle-pool sequences are responsible for most of the N-processing, despite the fact that fluvial ripples generate 3-11 times more hyporheic exchange flux. Across all scenarios, hyporheic exchange flux and the Damkohler Number emerge as primary controls on stream N-cycling; the former regulates trafficking of nutrients and oxygen across the sediment-water interface, while the latter quantifies the relative rates of organic carbon mineralization and advective transport in streambed sediments. Vertical groundwater flux modulates both of these master variables in ways that tend to diminish stream N-cycling. Thus, anthropogenic perturbations of ambient groundwater flows (e.g., by urbanization, agricultural activities, groundwater mining, and/or climate change) may compromise some of the key ecosystem services provided by streams.

  13. Patterns in groundwater chemistry resulting from groundwater flow

    Science.gov (United States)

    Stuyfzand, Pieter J.

    Groundwater flow influences hydrochemical patterns because flow reduces mixing by diffusion, carries the chemical imprints of biological and anthropogenic changes in the recharge area, and leaches the aquifer system. Global patterns are mainly dictated by differences in the flux of meteoric water passing through the subsoil. Within individual hydrosomes (water bodies with a specific origin), the following prograde evolution lines (facies sequence) normally develop in the direction of groundwater flow: from strong to no fluctuations in water quality, from polluted to unpolluted, from acidic to basic, from oxic to anoxic-methanogenic, from no to significant base exchange, and from fresh to brackish. This is demonstrated for fresh coastal-dune groundwater in the Netherlands. In this hydrosome, the leaching of calcium carbonate as much as 15m and of adsorbed marine cations (Na+, K+, and Mg2+) as much as 2500m in the flow direction is shown to correspond with about 5000yr of flushing since the beach barrier with dunes developed. Recharge focus areas in the dunes are evidenced by groundwater displaying a lower prograde quality evolution than the surrounding dune groundwater. Artificially recharged Rhine River water in the dunes provides distinct hydrochemical patterns, which display groundwater flow, mixing, and groundwater ages. Résumé Les écoulements souterrains influencent les différents types hydrochimiques, parce que l'écoulement réduit le mélange par diffusion, porte les marques chimiques de changements biologiques et anthropiques dans la zone d'alimentation et lessive le système aquifère. Ces types dans leur ensemble sont surtout déterminés par des différences dans le flux d'eau météorique traversant le sous-sol. Dans les "hydrosomes" (masses d'eau d'origine déterminée), les lignes marquant une évolution prograde (séquence de faciès) se développent normalement dans la direction de l'écoulement souterrain : depuis des fluctuations fortes de la

  14. Site scale groundwater flow in Olkiluoto - complementary simulations

    Energy Technology Data Exchange (ETDEWEB)

    Loefman, J. [VTT Energy, Espoo (Finland)

    2000-06-01

    This work comprises of the complementary simulations to the previous groundwater flow analysis at the Olkiluoto site. The objective is to study the effects of flow porosity, conceptual model for solute transport, fracture zones, land uplift and initial conditions on the results. The numerical simulations are carried out up to 10000 years into the future employing the same modelling approach and site-specific flow and transport model as in the previous work except for the differences in the case descriptions. The result quantities considered are the salinity and the driving force in the vicinity of the repository. The salinity field and the driving force are sensitive to the flow porosity and the conceptual model for solute transport. Ten-fold flow porosity and the dual-porosity approach retard the transport of solutes in the bedrock resulting in brackish groundwater conditions at the repository at 10000 years A.P. (in the previous work the groundwater in the repository turned into fresh). The higher driving forces can be attributed to the higher concentration gradients resulting from the opposite effects of the land uplift, which pushes fresh water deeper and deeper into the bedrock, and the higher flow porosity and the dual-porosity model, which retard the transport of solutes. The cases computed (unrealistically) without fracture zones and postglacial land uplift show that they both have effect on the results and can not be ignored in the coupled and transient groundwater flow analyses. The salinity field and the driving force are also sensitive to the initial salinity field especially at the beginning during the first 500 years A.P. The sensitivity will, however, diminish as soon as fresh water dilutes brackish and saline water and decreases the concentration gradients. Fresh water conditions result in also a steady state for the driving force in the repository area. (orig.)

  15. Development of conceptual groundwater flow model for Pali Area ...

    African Journals Online (AJOL)

    The study also extensively uses GIS for preprocessing of hydrological, hydrogeological and geological data. In our view, the methodology presented here provides better tools for building a conceptual model for tackling groundwater modeling problems. Keywords: Groundwater flow model, conceptual model, groundwater ...

  16. Simulation of groundwater flow and analysis of the effects of water-management options in the North Platte Natural Resources District, Nebraska

    Science.gov (United States)

    Peterson, Steven M.; Flynn, Amanda T.; Vrabel, Joseph; Ryter, Derek W.

    2015-08-12

    The North Platte Natural Resources District (NPNRD) has been actively collecting data and studying groundwater resources because of concerns about the future availability of the highly inter-connected surface-water and groundwater resources. This report, prepared by the U.S. Geological Survey in cooperation with the North Platte Natural Resources District, describes a groundwater-flow model of the North Platte River valley from Bridgeport, Nebraska, extending west to 6 miles into Wyoming. The model was built to improve the understanding of the interaction of surface-water and groundwater resources, and as an optimization tool, the model is able to analyze the effects of water-management options on the simulated stream base flow of the North Platte River. The groundwater system and related sources and sinks of water were simulated using a newton formulation of the U.S. Geological Survey modular three-dimensional groundwater model, referred to as MODFLOW–NWT, which provided an improved ability to solve nonlinear unconfined aquifer simulations with wetting and drying of cells. Using previously published aquifer-base-altitude contours in conjunction with newer test-hole and geophysical data, a new base-of-aquifer altitude map was generated because of the strong effect of the aquifer-base topography on groundwater-flow direction and magnitude. The largest inflow to groundwater is recharge originating from water leaking from canals, which is much larger than recharge originating from infiltration of precipitation. The largest component of groundwater discharge from the study area is to the North Platte River and its tributaries, with smaller amounts of discharge to evapotranspiration and groundwater withdrawals for irrigation. Recharge from infiltration of precipitation was estimated with a daily soil-water-balance model. Annual recharge from canal seepage was estimated using available records from the Bureau of Reclamation and then modified with canal

  17. Impact of the Wisconsinian Glaciation on Canadian Continental Groundwater Flow

    Science.gov (United States)

    Lemieux, J.; Sudicky, E. A.; Peltier, W. R.; Tarasov, L.

    2005-12-01

    During the last glacial period (75 kyr - 10 kyr), the Canadian landscape was almost entirely covered with ice. The Laurentide ice-sheet, the largest of the three North-American ice sheets, reached a thickness of about 4 km and the force exerted by its weight on the earth's crust was sufficient to cause a depression of the surface of about 1 km and an over-pressurization of porewater fluids. These dramatic conditions are suspected to have had a large impact on the groundwater flow system over the whole continent. Although an analysis of the evolution of groundwater flow systems during glacial periods is relevant to a number of problems, such as the long-term stability of high-level spent nuclear-fuel repositories located at depth, very few studies have been conducted to assess the impact of glaciation on deep-seated groundwater flow systems, particularly in a North-American context. A transient, three-dimensional groundwater flow model including the effect of the advective-dispersive redistribution of shield brines was constructed in order to capture the impact of the advance and retreat of the ice sheet over the Canadian landscape. The model is driven by a thermomechanical ice-sheet model of the last glacial cycle [Tarasov and Peltier, 2004] which provides the transient boundary conditions that includes the spatio-temporal distribution of the glacial ice, the elevation of the surface topography, meltwater rates, permafrost thicknesses, as well as temporal changes in sea level along the coastal margins. The evolving surface water drainage patterns and features such as proglacial lakes are also incorporated based on the hydrologic routing calculations performed by Tarasov and Peltier [2005]. The treatment of physical processes related to the influence of the ice sheet on the groundwater flow system such as hydromechanics, isostasy, subglacial melting and permafrost formation are also discussed. Simulation results show that hydraulic heads at depth below the ice sheet

  18. Simulations of Groundwater Flow and Particle Tracking Analysis in the Area Contributing Recharge to a Public-Supply Well near Tampa, Florida, 2002-05

    Science.gov (United States)

    Crandall, Christy A.; Kauffman, Leon J.; Katz, Brian G.; Metz, Patricia A.; McBride, W. Scott; Berndt, Marian P.

    2009-01-01

    Shallow ground water in the north-central Tampa Bay region, Florida, is affected by elevated nitrate concentrations, the presence of volatile organic compounds, and pesticides as a result of groundwater development and intensive urban land use. The region relies primarily on groundwater for drinking-water supplies. Sustainability of groundwater quality for public supply requires monitoring and understanding of the mechanisms controlling the vulnerability of public-supply wells to contamination. A single public-supply well was selected for intensive study based on the need to evaluate the dominant processes affecting the vulnerability of public-supply wells in the Upper Floridan aquifer in the City of Temple Terrace near Tampa, Florida, and the presence of a variety of chemical constituents in water from the well. A network of 29 monitoring wells was installed, and water and sediment samples were collected within the area contributing recharge to the selected public-supply well to support a detailed analysis of physical and chemical conditions and processes affecting the water chemistry in the well. A three-dimensional, steady-state groundwater flow model was developed to evaluate the age of groundwater reaching the well and to test hypotheses on the vulnerability of the well to nonpoint source input of nitrate. Particle tracking data were used to calculate environmental tracer concentrations of tritium and sulfur hexafluoride and to calibrate traveltimes and compute flow paths and advective travel times in the model area. The traveltime of particles reaching the selected public-supply well ranged from less than 1 day to 127.0 years, with a median of 13.1 years; nearly 45 percent of the simulated particle ages were less than about 10 years. Nitrate concentrations, derived primarily from residential/commercial fertilizer use and atmospheric deposition, were highest (2.4 and 6.11 milligrams per liter as nitrogen, median and maximum, respectively) in shallow

  19. Radionuclides in groundwater flow system understanding

    Science.gov (United States)

    Erőss, Anita; Csondor, Katalin; Horváth, Ákos; Mádl-Szőnyi, Judit; Surbeck, Heinz

    2017-04-01

    Using radionuclides is a novel approach to characterize fluids of groundwater flow systems and understand their mixing. Particularly, in regional discharge areas, where different order flow systems convey waters with different temperature, composition and redox-state to the discharge zone. Radium and uranium are redox-sensitive parameters, which causes fractionation along groundwater flow paths. Discharging waters of regional flow systems are characterized by elevated total dissolved solid content (TDS), temperature and by reducing conditions, and therefore with negligible uranium content, whereas local flow systems have lower TDS and temperature and represent oxidizing environments, and therefore their radium content is low. Due to the short transit time, radon may appear in local systems' discharge, where its source is the soil zone. However, our studies revealed the importance of FeOOH precipitates as local radon sources throughout the adsorption of radium transported by the thermal waters of regional flow systems. These precipitates can form either by direct oxidizing of thermal waters at discharge, or by mixing of waters with different redox state. Therefore elevated radon content often occurs in regional discharge areas as well. This study compares the results of geochemical studies in three thermal karst areas in Hungary, focusing on radionuclides as natural tracers. In the Buda Thermal Karst, the waters of the distinct discharge areas are characterized by different temperature and chemical composition. In the central discharge area both lukewarm (20-35°C, 770-980 mg/l TDS) and thermal waters (40-65°C, 800-1350 mg/l TDS), in the South only thermal water discharge (33-43°C, 1450-1700 mg/l TDS) occur. Radionuclides helped to identify mixing of fluids and to infer the temperature and chemical composition of the end members for the central discharge area. For the southern discharge zone mixing components could not be identified, which suggests different cave

  20. Characterizing Groundwater Level and Flow Pattern in a Shallow ...

    African Journals Online (AJOL)

    The static water level, groundwater flow direction, surface profile and 3-D elevation model of the study area were produced from the data collected using ArcGis 9.3 and surfer 8 GIS software. The groundwater flow direction in the study is towards the southwestern part of the study area with few exceptions as the case of Ikota ...

  1. Is in situ stress important to groundwater flow in shallow fractured rock aquifers?

    Science.gov (United States)

    Mortimer, L.; Aydin, A.; Simmons, C. T.; Love, A. J.

    2011-03-01

    SummaryIn situ stress affects the permeability tensor of fractured rock masses at depth but its effect on shallow to near-surface fractured rock aquifers has received little attention. This is partly because stress-related effects on groundwater flow at shallow depths are difficult to identify and characterise due to the complex interactions between all of the inherent properties of a fractured rock aquifer. These properties include the factors that dominantly control groundwater flow: fracture network density, geometry, connectivity and infill. Furthermore, surface processes such as weathering, erosion and unloading alter the original hydraulic nature (connectivity, transmissivity) of fractured rock masses resulting in higher degrees of spatial heterogeneity within shallow flow systems. These processes and interactions often mask the influence of in situ stress fields on fracture network permeability and groundwater flow. In this study, an integrated analysis of local area fracture networks, borehole geophysical logs, borehole groundwater yields and hydromechanical models demonstrate that in situ stress does affect groundwater flow in shallow (fractured rock aquifers by altering fracture hydraulic aperture distributions, fracture network connectivity and groundwater flow rates via fracture deformation processes. In particular, a comparison between representative models of deformed (stressed state) and undeformed (zero stress state) fracture networks showed that below 100 m depth, groundwater flow rates could decrease several fold under the influence of the contemporary stress field. This prediction was highly consistent with the field observations. In contrast, groundwater flow modelling of shallow fractured rock aquifers is typically conducted under the assumption that permeability is independent of the state of stress. A key finding of this study is that in situ stress may be a more important control on both local and regional scale shallow groundwater flow

  2. Modelling framework for groundwater flow at Sellafield

    International Nuclear Information System (INIS)

    Hooper, A.J.; Billington, D.E.; Herbert, A.W.

    1995-01-01

    The principal objective of Nirex is to develop a single deep geological repository for the safe disposal of low- and intermediate-level radioactive waste. In safety assessment, use is made of a variety of conceptual models that form the basis for modelling of the pathways by which radionuclides might return to the environment. In this paper, the development of a conceptual model for groundwater flow and transport through fractured rock on the various scales of interest is discussed. The approach is illustrated by considering how some aspects of the conceptual model are developed in particular numerical models. These representations of the conceptual model use fracture network geometries based on realistic rock properties. (author). refs., figs., tabs

  3. Simulations of Ground-Water Flow and Particle Pathline Analysis in the Zone of Contribution of a Public-Supply Well in Modesto, Eastern San Joaquin Valley, California

    Science.gov (United States)

    Burow, Karen R.; Jurgens, Bryant C.; Kauffman, Leon J.; Phillips, Steven P.; Dalgish, Barbara A.; Shelton, Jennifer L.

    2008-01-01

    Shallow ground water in the eastern San Joaquin Valley is affected by high nitrate and uranium concentrations and frequent detections of pesticides and volatile organic compounds (VOC), as a result of ground-water development and intensive agricultural and urban land use. A single public-supply well was selected for intensive study to evaluate the dominant processes affecting the vulnerability of public-supply wells in the Modesto area. A network of 23 monitoring wells was installed, and water and sediment samples were collected within the approximate zone of contribution of the public-supply well, to support a detailed analysis of physical and chemical conditions and processes affecting the water chemistry in the well. A three-dimensional, steady-state local ground-water-flow and transport model was developed to evaluate the age of ground water reaching the well and to evaluate the vulnerability of the well to nonpoint source input of nitrate and uranium. Particle tracking was used to compute pathlines and advective travel times in the ground-water flow model. The simulated ages of particles reaching the public-supply well ranged from 9 to 30,000 years, with a median of 54 years. The age of the ground water contributed to the public-supply well increased with depth below the water table. Measured nitrate concentrations, derived primarily from agricultural fertilizer, were highest (17 milligrams per liter) in shallow ground water and decreased with depth to background concentrations of less than 2 milligrams per liter in the deepest wells. Because the movement of water is predominantly downward as a result of ground-water development, and because geochemical conditions are generally oxic, high nitrate concentrations in shallow ground water are expected to continue moving downward without significant attenuation. Simulated long-term nitrate concentrations indicate that concentrations have peaked and will decrease in the public-supply well during the next 100 years

  4. Hanford statewide groundwater flow and transport model calibration report

    International Nuclear Information System (INIS)

    Law, A.; Panday, S.; Denslow, C.; Fecht, K.; Knepp, A.

    1996-04-01

    This report presents the results of the development and calibration of a three-dimensional, finite element model (VAM3DCG) for the unconfined groundwater flow system at the Hanford Site. This flow system is the largest radioactively contaminated groundwater system in the United States. Eleven groundwater plumes have been identified containing organics, inorganics, and radionuclides. Because groundwater from the unconfined groundwater system flows into the Columbia River, the development of a groundwater flow model is essential to the long-term management of these plumes. Cost effective decision making requires the capability to predict the effectiveness of various remediation approaches. Some of the alternatives available to remediate groundwater include: pumping contaminated water from the ground for treatment with reinjection or to other disposal facilities; containment of plumes by means of impermeable walls, physical barriers, and hydraulic control measures; and, in some cases, management of groundwater via planned recharge and withdrawals. Implementation of these methods requires a knowledge of the groundwater flow system and how it responds to remedial actions

  5. Vulnerability assessment of groundwater-dependent ecosystems based on integrated groundwater flow modell construction

    Science.gov (United States)

    Tóth, Ádám; Simon, Szilvia; Galsa, Attila; Havril, Timea; Monteiro Santos, Fernando A.; Müller, Imre; Mádl-Szőnyi, Judit

    2017-04-01

    Groundwater-dependent ecosystems (GDEs) are highly influenced by the amount of groundwater, seasonal variation of precipitation and consequent water table fluctuation and also the anthropogenic activities. They can be regarded as natural surface manifestations of the flowing groundwater. The preservation of environment and biodiversity of these GDEs is an important issue worldwide, however, the water management policy and action plan could not be constructed in absense of proper hydrogeological knowledge. The concept of gravity-driven regional groundwater flow could aid the understanding of flow pattern and interpretation of environmental processes and conditions. Unless the required well data are available, the geological-hydrogeological numerical model of the study area cannot be constructed based only on borehole information. In this case, spatially continuous geophysical data can support groundwater flow model building: systematically combined geophysical methods can provide model input. Integration of lithostratigraphic, electrostratigraphic and hydrostratigraphic information could aid groundwater flow model construction: hydrostratigraphic units and their hydraulic behaviour, boundaries and geometry can be obtained. Groundwater-related natural manifestations, such as GDEs, can be explained with the help of the revealed flow pattern and field mapping of features. Integrated groundwater flow model construction for assessing the vulnerability of GDEs was presented via the case study of the geologically complex area of Tihany Peninsula, Hungary, with the aims of understanding the background and occurrence of groundwater-related environmental phenomena, surface water-groundwater interaction, and revealing the potential effect of anthropogenic activity and climate change. In spite of its important and protected status, fluid flow model of the area, which could support water management and natural protection policy, had not been constructed previously. The 3D

  6. Three-dimensional analysis of future groundwater flow conditions and contaminant plume transport in the Hanford Site unconfined aquifer system: FY 1996 and 1997 status report

    International Nuclear Information System (INIS)

    Cole, C.R.; Wurstner, S.K.; Williams, M.D.; Thorne, P.D.; Bergeron, M.P.

    1997-12-01

    A three-dimensional numerical model of groundwater flow and transport, based on the Coupled Fluid Energy, and Solute Transport (CFEST) code, was developed for the Hanford Site to support the Hanford Groundwater Project (HGWP), managed by Pacific Northwest National Laboratory. The model was developed to increase the understanding and better forecast the migration of several contaminant plumes being monitored by the HGWP, and to support the Hanford Site Composite Analysis for low-level waste disposal in the 200-Area Plateau. Recent modeling efforts have focused on continued refinement of an initial version of the three-dimensional model developed in 1995 and its application to simulate future transport of selected contaminant plumes in the aquifer system. This version of the model was updated using a more current version of the CFEST code called CFEST96. Prior to conducting simulations of contaminant transport with the three-dimensional model, a previous steady-state, two-dimensional model of the unconfined aquifer system was recalibrated to 1979 water-table conditions with a statistical inverse method implemented in the CFEST-INV computer code. The results of the recalibration were used to refine the three-dimensional conceptual model and to calibrate it with a conceptualization that preserves the two-dimensional hydraulic properties and knowledge of the aquifer's three-dimensional properties for the same 1979 water-table conditions. The transient behavior of the three-dimensional flow model was also calibrated by adjusting model storage properties (specific yield) until transient water-table predictions approximated observed water-table elevations between 1979 and 1996

  7. Three-dimensional analysis of future groundwater flow conditions and contaminant plume transport in the Hanford Site unconfined aquifer system: FY 1996 and 1997 status report

    Energy Technology Data Exchange (ETDEWEB)

    Cole, C.R.; Wurstner, S.K.; Williams, M.D.; Thorne, P.D.; Bergeron, M.P.

    1997-12-01

    A three-dimensional numerical model of groundwater flow and transport, based on the Coupled Fluid Energy, and Solute Transport (CFEST) code, was developed for the Hanford Site to support the Hanford Groundwater Project (HGWP), managed by Pacific Northwest National Laboratory. The model was developed to increase the understanding and better forecast the migration of several contaminant plumes being monitored by the HGWP, and to support the Hanford Site Composite Analysis for low-level waste disposal in the 200-Area Plateau. Recent modeling efforts have focused on continued refinement of an initial version of the three-dimensional model developed in 1995 and its application to simulate future transport of selected contaminant plumes in the aquifer system. This version of the model was updated using a more current version of the CFEST code called CFEST96. Prior to conducting simulations of contaminant transport with the three-dimensional model, a previous steady-state, two-dimensional model of the unconfined aquifer system was recalibrated to 1979 water-table conditions with a statistical inverse method implemented in the CFEST-INV computer code. The results of the recalibration were used to refine the three-dimensional conceptual model and to calibrate it with a conceptualization that preserves the two-dimensional hydraulic properties and knowledge of the aquifer`s three-dimensional properties for the same 1979 water-table conditions. The transient behavior of the three-dimensional flow model was also calibrated by adjusting model storage properties (specific yield) until transient water-table predictions approximated observed water-table elevations between 1979 and 1996.

  8. The limited and localized flow of fresh groundwater to the world's oceans

    Science.gov (United States)

    Luijendijk, E.; Gleeson, T. P.; Moosdorf, N.

    2017-12-01

    Submarine groundwater discharge, the flow of fresh or saline groundwater to oceans [Burnett et al., 2003], may be a significant contributor to the water and chemical budgets of the world's oceans [Taniguchi et al., 2002] potentially buffering ocean acidification with groundwater alkalinity and is arguably the most uncertain component of the global groundwater budget [Alley et al., 2002]. The fresh component of submarine groundwater discharge is critical due to its high solute and nutrient load, and has been quantified locally and but only roughly estimated globally using significant assumptions. Here we show that that fresh submarine groundwater discharge is an insignificant water contributor to global oceans (0.05% of the total input) but that the freshwater discharge may still be an important chemical and nutrient contributor especially around distinct hotspots. The first spatially-explicit, physically-based global estimate of fresh submarine groundwater discharge was derived by combining density-dependent numerical groundwater models and a geospatial analysis of global coastal watersheds to robustly simulate the partitioning of onshore and offshore groundwater discharge. Although fresh submarine groundwater discharge is an insignificant part of fresh coastal groundwater discharge, results are consistent with previous estimates of significant recirculated seawater discharging as groundwater as well as quantifying the significant near-shore terrestrial discharge, a flux that has so far been overlooked in global hydrological studies and that affects coastal water budgets, evapotranspiration and ecosystems.

  9. A modified calculation model for groundwater flowing to horizontal ...

    Indian Academy of Sciences (India)

    well pipe and aquifer couples the turbulent flow inside the horizontal seepage well with laminar flow in the aquifer. .... In the well pipe, the relationship between hydraulic head loss and flow velocity .... the steady-state mathematic model is developed for groundwater flowing to the horizontal seepage well under a river valley.

  10. Effects of geological structures on groundwater flow and quality in ...

    Indian Academy of Sciences (India)

    Analysis and field observations revealed that the north–south dykes act as a barrier of groundwater while the west–east oriented structures behave as a carrier of groundwater. Both quality and quantity of groundwater is different on the upstream and downstream sides of the dyke. Hence, it is conclusive that the west–east ...

  11. Hydrogeology and simulation of groundwater flow and analysis of projected water use for the Canadian River alluvial aquifer, western and central Oklahoma

    Science.gov (United States)

    Ellis, John H.; Mashburn, Shana L.; Graves, Grant M.; Peterson, Steven M.; Smith, S. Jerrod; Fuhrig, Leland T.; Wagner, Derrick L.; Sanford, Jon E.

    2017-02-13

    This report describes a study of the hydrogeology and simulation of groundwater flow for the Canadian River alluvial aquifer in western and central Oklahoma conducted by the U.S. Geological Survey in cooperation with the Oklahoma Water Resources Board. The report (1) quantifies the groundwater resources of the Canadian River alluvial aquifer by developing a conceptual model, (2) summarizes the general water quality of the Canadian River alluvial aquifer groundwater by using data collected during August and September 2013, (3) evaluates the effects of estimated equal proportionate share (EPS) on aquifer storage and streamflow for time periods of 20, 40, and 50 years into the future by using numerical groundwater-flow models, and (4) evaluates the effects of present-day groundwater pumping over a 50-year period and sustained hypothetical drought conditions over a 10-year period on stream base flow and groundwater in storage by using numerical flow models. The Canadian River alluvial aquifer is a Quaternary-age alluvial and terrace unit consisting of beds of clay, silt, sand, and fine gravel sediments unconformably overlying Tertiary-, Permian-, and Pennsylvanian-age sedimentary rocks. For groundwater-flow modeling purposes, the Canadian River was divided into Reach I, extending from the Texas border to the Canadian River at the Bridgeport, Okla., streamgage (07228500), and Reach II, extending downstream from the Canadian River at the Bridgeport, Okla., streamgage (07228500), to the confluence of the river with Eufaula Lake. The Canadian River alluvial aquifer spans multiple climate divisions, ranging from semiarid in the west to humid subtropical in the east. The average annual precipitation in the study area from 1896 to 2014 was 34.4 inches per year (in/yr).A hydrogeologic framework of the Canadian River alluvial aquifer was developed that includes the areal and vertical extent of the aquifer and the distribution, texture variability, and hydraulic properties of

  12. From groundwater baselines to numerical groundwater flow modelling for the Milan metropolitan area

    Science.gov (United States)

    Crosta, Giovanni B.; Frattini, Paolo; Peretti, Lidia; Villa, Federica; Gorla, Maurizio

    2015-04-01

    Contamination of major aquifers in highly densely populated areas is a major concern for stakeholders involved in the use and protection of groundwater resources. Sustainable groundwater withdrawal and management, and the identification of trends in groundwater contamination require a careful hydrochemical baseline characterization. This characterization is fundamental to investigate the presence and evolutionary trend of contaminants. In fact, it allows recovering and understanding: the spatial-temporal trend of contamination; the relative age of the contamination episodes; the reasons for anomalous behavior of some compounds during migration to and in the groundwater; the associations with which some contaminants can be found; the different behaviors in phreatic and semi-confined and confined aquifers. To attain such a characterization for the Milan metropolitan area (about 2,500 km2, ca 4.000.000 inhabitants, Lombardy, Italy), we carried out three main activities. (1) Collection of complete and reliable datasets concerning the geological, hydrogeological and hydrochemical (over 60,000 chemical analysis since 2003 to 2013) characteristics of the area and of the involved aquifers. This activity was very demanding because the available data are provided by different authorities (Lombardy Region, Provinces, Lombardy Environmental Agency - ARPA Lombardia, public own companies in charge of water system managements) in raw format and with different database standard, which required a large effort of manual verification and harmonization. (2) Completion of a hydrochemical characterization of the metropolitan area aquifers by classical statistical and multivariate statistical analyses, in order to define a baseline both for some major physical chemical characteristics and for the most relevant contaminants. (3) Development of a three dimensional hydrogeological model for the metropolitan area starting from the above listed datasets and existing models. This model will

  13. Supra regional ground water modelling - in-depth analysis of the groundwater flow patterns in eastern Smaaland. Comparison with different conceptual descriptions; Storregional grundvattenmodellering - foerdjupad analys av floedesfoerhaallanden i oestra Smaaland. Jaemfoerelse av olika konceptuella beskrivningar

    Energy Technology Data Exchange (ETDEWEB)

    Ericsson, Lars O. [Lars O Ericsson Consulting AB, Stockholm (Sweden); Holmen, Johan [Golder Associates, Uppsala (Sweden); Rhen, Ingvar; Blomquist, Niklas [SWECO VIAK, Stockholm (Sweden)

    2006-05-15

    One of many geoscientific questions in connection with the siting of a final repository for spent nuclear fuel in Sweden has to do with understanding the large-scale flow patterns of the naturally circulating groundwater. The recharge and discharge of the groundwater is therefore a subject for both SKB's research activities and the interest of the regulatory authorities. This report aims at providing an in-depth scientific analysis of the groundwater flow pattern based on the criteria and suitability indicators which SKB has previously presented with respect to recharge and discharge aspects in a supra regional perspective. The analysis was conducted within the framework of a project whose goals were to: evaluate conceptual simplifications and model uncertainties in supra regional groundwater modelling, and to carry out an in-depth and comprehensive analysis of regional flow conditions in eastern Smaaland. Achieving these goals has required an approach based on the use of available geoscientific data on the Smaaland region combined with an analysis of different conceptual assumptions and system descriptions. The following general conclusions can be drawn from the study and the applied methodology: The factor of greatest importance for the regional flow pattern (from repository depth) is the topography. The discharge areas are mainly found in the low-lying parts of the topography, along valleys, and the recharge areas occur on the heights. The topographic undulation is of greater importance than the properties of the conductivity field. Different lithological units, regional deformation zones, local heterogeneity, Quaternary deposits etc are of less importance than the undulation of the topography. For areas described and analyzed with the most realistic assumptions, the groundwater flow pattern can be described as a primarily local flow process. The median flow path length in the study is on the order of 2 km, and the fraction of supra regional flow paths

  14. Interpreting Repeated Temperature-Depth Profiles for Groundwater Flow

    NARCIS (Netherlands)

    Bense, Victor F.; Kurylyk, Barret L.; Daal, van Jonathan; Ploeg, van der Martine J.; Carey, Sean K.

    2017-01-01

    Temperature can be used to trace groundwater flows due to thermal disturbances of subsurface advection. Prior hydrogeological studies that have used temperature-depth profiles to estimate vertical groundwater fluxes have either ignored the influence of climate change by employing steady-state

  15. Effects of geological structures on groundwater flow and quality in ...

    Indian Academy of Sciences (India)

    Geological and structural influences on groundwater flow and quality were evaluated in the present study in the hardrock regions of Tirunelveli District, southern India. Groundwater is a major source of freshwater in this region to cater to the requirements of domestic and agricultural activity, as there are no surface water ...

  16. Groundwater flow modeling of Kwa Ibo river watershed ...

    African Journals Online (AJOL)

    Groundwater flow modeling of Kwa Ibo River Watershed in Abia State of Nigeria is presented in this paper with the aim of assessing the degree of interaction between the Kwa Ibo River and the groundwater regime of the thick sandy aquifer. The local geology of the area, called Benin Formation, is of Quaternary to Recent ...

  17. General Separations Area (GSA) Groundwater Flow Model Update: Hydrostratigraphic Data

    Energy Technology Data Exchange (ETDEWEB)

    Bagwell, L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Bennett, P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Flach, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-02-21

    This document describes the assembly, selection, and interpretation of hydrostratigraphic data for input to an updated groundwater flow model for the General Separations Area (GSA; Figure 1) at the Department of Energy’s (DOE) Savannah River Site (SRS). This report is one of several discrete but interrelated tasks that support development of an updated groundwater model (Bagwell and Flach, 2016).

  18. Groundwater recharge and flow on Montserrat, West Indies: Insights from groundwater dating

    Directory of Open Access Journals (Sweden)

    Brioch Hemmings

    2015-09-01

    New hydrological insights: δ2H and δ18O analysis indicates uniform recharge elevations for groundwaters on Montserrat. CFC-11 and CFC-12 analysis reveals age differences between isotopically similar, high elevation springs and low elevation aquifer waters. Low CFC concentrations within a confined low elevation aquifer suggest water ages of ∼45 years. High CFC concentrations in the northern and western springs are explained by rapid infiltration of cool (high CFC concentration rainfall into saturated compartments, with flow through the vadose zone to the phreatic zone dominated by compartment flow. Lower CFC concentrations in a number of aligned warmer springs suggest a contribution from older, warmer waters from depth. Temperatures and CFC concentrations indicate older component supply rates of up to 8 L/s to the highest yielding spring on Centre Hills, with contributions of up to 75% in the warmest spring waters.

  19. Simulation of the groundwater flow of the Kivetty area

    International Nuclear Information System (INIS)

    Taivassalo, V.; Meszaros, F.

    1994-02-01

    Teollisuuden Voima Oy (TVO) is preparing for the final disposal of spent nuclear fuel into crystalline bedrock in Finland. Groundwater flow modelling is a part of the preliminary site investigation work. The aim is to simulate groundwater flow as realistically as possible in view of the experimental data available. Three dimensional groundwater flow modelling is based on a conceptual bedrock model. The modelling results will be used in the site evaluation process. Observations from flow simulations will also be used to identify and study uncertainties included in the site characterization. First a conceptual flow model for the Kivetty site in Konginkangas was developed. As a second stage the flow model was calibrated. The goal was to increase the reality of the model. To evaluate the reality of the flow model, the values of the input and output parameters were compared with the field data. Finally groundwater flow simulation results were computed and groundwater flow at the Kivetty area was analysed. (50 refs., 78 figs., 7 tabs.)

  20. Simulation of Groundwater Flow, Denpasar-Tabanan Groundwater Basin, Bali Province

    Directory of Open Access Journals (Sweden)

    Heryadi Tirtomihardjo

    2014-06-01

    Full Text Available DOI: 10.17014/ijog.v6i3.123Due to the complex structure of the aquifer systems and its hydrogeological units related with the space in which groundwater occurs, groundwater flows were calculated in three-dimensional method (3D Calculation. The geometrical descritization and iteration procedures were based on an integrated finite difference method. In this paper, all figures and graphs represent the results of the calibrated model. Hence, the model results were simulated by using the actual input data which were calibrated during the simulation runs. Groundwater flow simulation of the model area of the Denpasar-Tabanan Groundwater Basin (Denpasar-Tabanan GB comprises steady state run, transient runs using groundwater abstraction in the period of 1989 (Qabs-1989 and period of 2009 (Qabs-2009, and prognosis run as well. Simulation results show, in general, the differences of calculated groundwater heads and observed groundwater heads at steady and transient states (Qabs-1989 and Qabs-2009 are relatively small. So, the groundwater heads situation simulated by the prognosis run (scenario Qabs-2012 are considerably valid and can properly be used for controlling the plan of groundwater utilization in Denpasar-Tabanan GB.

  1. PUMa - modelling the groundwater flow in Baltic Sedimentary Basin

    Science.gov (United States)

    Kalvane, G.; Marnica, A.; Bethers, U.

    2012-04-01

    In 2009-2012 at University of Latvia and Latvia University of Agriculture project "Establishment of interdisciplinary scientist group and modelling system for groundwater research" is implemented financed by the European Social Fund. The aim of the project is to develop groundwater research in Latvia by establishing interdisciplinary research group and modelling system covering groundwater flow in the Baltic Sedimentary Basin. Researchers from fields like geology, chemistry, mathematical modelling, physics and environmental engineering are involved in the project. The modelling system is used as a platform for addressing scientific problems such as: (1) large-scale groundwater flow in Baltic Sedimentary Basin and impact of human activities on it; (2) the evolution of groundwater flow since the last glaciation and subglacial groundwater recharge; (3) the effects of climate changes on shallow groundwater and interaction of hydrographical network and groundwater; (4) new programming approaches for groundwater modelling. Within the frame of the project most accessible geological information such as description of geological wells, geological maps and results of seismic profiling in Latvia as well as Estonia and Lithuania are collected and integrated into modelling system. For example data form more then 40 thousands wells are directly used to automatically generate the geological structure of the model. Additionally a groundwater sampling campaign is undertaken. Contents of CFC, stabile isotopes of O and H and radiocarbon are the most significant parameters of groundwater that are established in unprecedented scale for Latvia. The most important modelling results will be published in web as a data set. Project number: 2009/0212/1DP/1.1.1.2.0/09/APIA/VIAA/060. Project web-site: www.puma.lu.lv

  2. Characterization of groundwater flow for near surface disposal facilities

    International Nuclear Information System (INIS)

    2001-02-01

    The main objective of this report is to provide a description of the site investigation techniques and modelling approaches that can be used to characterise the flow of subsurface water at near surface disposal facilities in relation to the various development stages of the repositories. As one of the main goals of defining groundwater flow is to establish the possible contaminant migration, certain aspects related to groundwater transport are also described. Secondary objectives are to discuss the implications of various groundwater conditions with regard to the performance of the isolation systems

  3. Numerical groundwater-flow modeling to evaluate potential effects of pumping and recharge: implications for sustainable groundwater management in the Mahanadi delta region, India

    Science.gov (United States)

    Sahoo, Sasmita; Jha, Madan K.

    2017-12-01

    Process-based groundwater models are useful to understand complex aquifer systems and make predictions about their response to hydrological changes. A conceptual model for evaluating responses to environmental changes is presented, considering the hydrogeologic framework, flow processes, aquifer hydraulic properties, boundary conditions, and sources and sinks of the groundwater system. Based on this conceptual model, a quasi-three-dimensional transient groundwater flow model was designed using MODFLOW to simulate the groundwater system of Mahanadi River delta, eastern India. The model was constructed in the context of an upper unconfined aquifer and lower confined aquifer, separated by an aquitard. Hydraulic heads of 13 shallow wells and 11 deep wells were used to calibrate transient groundwater conditions during 1997-2006, followed by validation (2007-2011). The aquifer and aquitard hydraulic properties were obtained by pumping tests and were calibrated along with the rainfall recharge. The statistical and graphical performance indicators suggested a reasonably good simulation of groundwater flow over the study area. Sensitivity analysis revealed that groundwater level is most sensitive to the hydraulic conductivities of both the aquifers, followed by vertical hydraulic conductivity of the confining layer. The calibrated model was then employed to explore groundwater-flow dynamics in response to changes in pumping and recharge conditions. The simulation results indicate that pumping has a substantial effect on the confined aquifer flow regime as compared to the unconfined aquifer. The results and insights from this study have important implications for other regional groundwater modeling studies, especially in multi-layered aquifer systems.

  4. Modifications to the modular three-dimensional finite-difference ground-water flow model used for the Columbia Plateau Regional Aquifer-System Analysis, Washington, Oregon, and Idaho

    Science.gov (United States)

    Hansen, A.J.

    1993-01-01

    The report documents modifications to the U.S. Geological Survey's modular three-dimensional finite-difference ground-water flow model used for a regional aquifer-system analysis of the Columbia Plateau. The report, which describes the concepts and mathematical basis for the modifications, is intended for potential users who are familiar with the original modular model. The modifications permit flow from a layer to any adjacent layer, allow the model to retain a cell of a layer that has been cut completely through by a canyon, and allow placing ground-water flow barriers on only specified branch conductances; a special version of the modified model uses a convergent grid. The report describes the data-input items that this modified model must read.

  5. Natural recharge estimation and uncertainty analysis of an adjudicated groundwater basin using a regional-scale flow and subsidence model (Antelope Valley, California, USA)

    Science.gov (United States)

    Siade, Adam J.; Nishikawa, Tracy; Martin, Peter

    2015-01-01

    Groundwater has provided 50–90 % of the total water supply in Antelope Valley, California (USA). The associated groundwater-level declines have led the Los Angeles County Superior Court of California to recently rule that the Antelope Valley groundwater basin is in overdraft, i.e., annual pumpage exceeds annual recharge. Natural recharge consists primarily of mountain-front recharge and is an important component of the total groundwater budget in Antelope Valley. Therefore, natural recharge plays a major role in the Court’s decision. The exact quantity and distribution of natural recharge is uncertain, with total estimates from previous studies ranging from 37 to 200 gigaliters per year (GL/year). In order to better understand the uncertainty associated with natural recharge and to provide a tool for groundwater management, a numerical model of groundwater flow and land subsidence was developed. The transient model was calibrated using PEST with water-level and subsidence data; prior information was incorporated through the use of Tikhonov regularization. The calibrated estimate of natural recharge was 36 GL/year, which is appreciably less than the value used by the court (74 GL/year). The effect of parameter uncertainty on the estimation of natural recharge was addressed using the Null-Space Monte Carlo method. A Pareto trade-off method was also used to portray the reasonableness of larger natural recharge rates. The reasonableness of the 74 GL/year value and the effect of uncertain pumpage rates were also evaluated. The uncertainty analyses indicate that the total natural recharge likely ranges between 34.5 and 54.3 GL/year.

  6. Natural recharge estimation and uncertainty analysis of an adjudicated groundwater basin using a regional-scale flow and subsidence model (Antelope Valley, California, USA)

    Science.gov (United States)

    Siade, Adam; Nishikawa, Tracy; Martin, Peter

    2015-09-01

    Groundwater has provided 50-90 % of the total water supply in Antelope Valley, California (USA). The associated groundwater-level declines have led the Los Angeles County Superior Court of California to recently rule that the Antelope Valley groundwater basin is in overdraft, i.e., annual pumpage exceeds annual recharge. Natural recharge consists primarily of mountain-front recharge and is an important component of the total groundwater budget in Antelope Valley. Therefore, natural recharge plays a major role in the Court's decision. The exact quantity and distribution of natural recharge is uncertain, with total estimates from previous studies ranging from 37 to 200 gigaliters per year (GL/year). In order to better understand the uncertainty associated with natural recharge and to provide a tool for groundwater management, a numerical model of groundwater flow and land subsidence was developed. The transient model was calibrated using PEST with water-level and subsidence data; prior information was incorporated through the use of Tikhonov regularization. The calibrated estimate of natural recharge was 36 GL/year, which is appreciably less than the value used by the court (74 GL/year). The effect of parameter uncertainty on the estimation of natural recharge was addressed using the Null-Space Monte Carlo method. A Pareto trade-off method was also used to portray the reasonableness of larger natural recharge rates. The reasonableness of the 74 GL/year value and the effect of uncertain pumpage rates were also evaluated. The uncertainty analyses indicate that the total natural recharge likely ranges between 34.5 and 54.3 GL/year.

  7. Assessing the velocity of the groundwater flow in bedrock fractures

    International Nuclear Information System (INIS)

    Taivassalo, V.; Poteri, A.

    1994-10-01

    Teollisuuden Voima Oy (TVO) is studying the crystalline bedrock in Finland for the final disposal of the spent nuclear fuel from its two reactors in Olkiluoto. Preliminary site investigations for five areas were carried out during 1987-1992. One part of the investigation programme was three-dimensional groundwater flow modelling. The numerical site-specific flow simulations were based on the concept of an equivalent porous continuum. The results include hydraulic head distributions, average groundwater flow rate routes. In this study, a novel approach was developed to evaluate the velocities of the water particles flowing in the fractured bedrock. (17 refs., 15 figs., 5 tabs.)

  8. Theory and verification for the GRASP II code for adjoint-sensitivity analysis of steady-state and transient ground-water flow

    Energy Technology Data Exchange (ETDEWEB)

    RamaRao, B.S.; Reeves, M. (INTERA, Inc., Austin, TX (USA))

    1990-10-01

    Calibration of a numerical model of the regional ground-water flow in the Culebra dolomite at the Waste Isolation Pilot Plant in southeastern New Mexico, has been performed by an interative parameter-fitting procedure. Parameterization has been secured by choosing to assign the transmissivity values at a limited number of selected locations, designated as pilot points. The transmissivity distribution in the model is derived by kriging the combined pool of measured and pilot-plant transmissivities. Iterating on the twin steps of sequentially adding additional pilot point(s) and kriging leads to the model of required accuracy, as judged by a weighted least-square-error objective function. At the end of calibration, it must be ensured that the correlation structure of the measured transmissivities is broadly preserved by the pilot-plant transmissivities. Adjoint-sensitivity analysis of the model has been coupled with kriging to provide objectively the optimal location of the pilot points during an iteration. The pilot-point transmissivities have been adjusted by modeler's judgement incorporating information, where available, on local geologic conditions and large-scale hydraulic interference tests, in order to minimize the objective function. 43 refs., 5 figs., 5 tabs.

  9. Simulations of groundwater flow and particle-tracking analysis in the zone of contribution to a public-supply well in San Antonio, Texas

    Science.gov (United States)

    Lindgren, Richard L.; Houston, Natalie A.; Musgrove, MaryLynn; Fahlquist, Lynne S.; Kauffman, Leon J.

    2011-01-01

    In 2006, a public-supply well in San Antonio, Texas, was selected for intensive study to assess the vulnerability of public-supply wells in the Edwards aquifer to contamination by a variety of compounds. A local-scale, steady-state, three-dimensional numerical groundwater-flow model was developed and used in this study to evaluate the movement of water and solutes from recharge areas to the selected public-supply well. Particle tracking was used to compute flow paths and advective traveltimes throughout the model area and to delineate the areas contributing recharge and zone of contribution for the selected public-supply well.

  10. GRASP [GRound-Water Adjunct Sensitivity Program]: A computer code to perform post-SWENT [simulator for water, energy, and nuclide transport] adjoint sensitivity analysis of steady-state ground-water flow: Technical report

    International Nuclear Information System (INIS)

    Wilson, J.L.; RamaRao, B.S.; McNeish, J.A.

    1986-11-01

    GRASP (GRound-Water Adjunct Senstivity Program) computes measures of the behavior of a ground-water system and the system's performance for waste isolation, and estimates the sensitivities of these measures to system parameters. The computed measures are referred to as ''performance measures'' and include weighted squared deviations of computed and observed pressures or heads, local Darcy velocity components and magnitudes, boundary fluxes, and travel distance and time along travel paths. The sensitivities are computed by the adjoint method and are exact derivatives of the performance measures with respect to the parameters for the modeled system, taken about the assumed parameter values. GRASP presumes steady-state, saturated grondwater flow, and post-processes the results of a multidimensional (1-D, 2-D, 3-D) finite-difference flow code. This document describes the mathematical basis for the model, the algorithms and solution techniques used, and the computer code design. The implementation of GRASP is verified with simple one- and two-dimensional flow problems, for which analytical expressions of performance measures and sensitivities are derived. The linkage between GRASP and multidimensional finite-difference flow codes is described. This document also contains a detailed user's manual. The use of GRASP to evaluate nuclear waste disposal issues has been emphasized throughout the report. The performance measures and their sensitivities can be employed to assist in directing data collection programs, expedite model calibration, and objectively determine the sensitivity of projected system performance to parameters

  11. Stochastic description of heterogeneities of permeability within groundwater flow models

    International Nuclear Information System (INIS)

    Cacas, M.C.; Lachassagne, P.; Ledoux, E.; Marsily, G. de

    1991-01-01

    In order to model radionuclide migration in the geosphere realistically at the field scale, the hydrogeologist needs to be able to simulate groundwater flow in heterogeneous media. Heterogeneity of the medium can be described using a stochastic approach, that affects the way in which a flow model is formulated. In this paper, we discuss the problems that we have encountered in modelling both continuous and fractured media. The stochastic approach leads to a methodology that enables local measurements of permeability to be integrated into a model which gives a good prediction of groundwater flow on a regional scale. 5 Figs.; 8 Refs

  12. A generalised groundwater flow equation using the concept of non ...

    African Journals Online (AJOL)

    head. This generalised law and the law of conservation of mass are then used to derive a new equation for groundwater flow. Numerical solutions of this equation for various fractional orders of the derivatives are compared with experimental data and the Barker generalised radial flow model for which a fractal dimension for ...

  13. Groundwater flow and heterogeneous discharge into a seepage lake

    DEFF Research Database (Denmark)

    Kazmierczak, Jolanta; Müller, Sascha; Nilsson, B.

    2016-01-01

    Groundwater discharge into a seepage lake was investigated by combining flux measurements, hydrochemical tracers, geological information, and a telescopic modeling approach using first two-dimensional (2-D) regional then 2-D local flow and flow path models. Discharge measurements and hydrochemica...

  14. A modified calculation model for groundwater flowing to horizontal ...

    Indian Academy of Sciences (India)

    The simulation models for groundwater flowing to horizontal seepage wells proposed by Wang and Zhang (2007) are based on the theory of coupled seepage-pipe flow model which treats the well pipe as a highly permeable medium. However, the limitations of the existing model were found during applications. Specifically ...

  15. Comparison of groundwater residence time using isotope techniques and numerical groundwater flow model in Gneissic Terrain, Korea

    International Nuclear Information System (INIS)

    Bae, D.S.; Kim, C.S.; Koh, Y.K.; Kim, K.S.; Song, M.Y.

    1997-01-01

    The prediction of groundwater flow affecting the migration of radionuclides is an important component of the performance assessment of radioactive waste disposal. Groundwater flow in fractured rock mass is controlled by fracture networks, transmissivity and hydraulic gradient. Furthermore the scale-dependent and anisotropic properties of hydraulic parameters are resulted mainly from irregular patterns of fracture system, which are very complex to evaluate properly with the current techniques available. For the purpose of characterizing a groundwater flow in fractured rock mass, the discrete fracture network (DFN) concept is available on the basis of assumptions of groundwater flowing only along fractures and flowpaths in rock mass formed by interconnected fractures. To increase the reliability of assessment in groundwater flow phenomena, numerical groundwater flow model and isotopic techniques were applied. Fracture mapping, borehole acoustic scanning were performed to identify conductive fractures in gneissic terrane. Tracer techniques, using deuterium, oxygen-18 and tritium were applied to evaluate the recharge area and groundwater residence time

  16. Simulation and particle-tracking analysis of ground-water flow near the Savannah River site, Georgia and South Carolina, 2002, and for selected ground-water management scenarios, 2002 and 2020

    Science.gov (United States)

    Cherry, Gregory S.

    2006-01-01

    Ground-water flow under 2002 hydrologic conditions was evaluated in an eight-county area in Georgia and South Carolina near the Savannah River Site (SRS), by updating boundary conditions and pumping rates in an existing U.S. Geological Survey (USGS) ground-water model. The original ground-water model, developed to simulate hydrologic conditions during 1987-92, used the quasi-three-dimensional approach by dividing the Floridan, Dublin, and Midville aquifer systems into seven aquifers. The hydrogeologic system was modeled using six active layers (A2-A7) that were separated by confining units with an overlying source-sink layer to simulate the unconfined Upper Three Runs aquifer (layer A1). Potentiometric- surface maps depicting September 2002 for major aquifers were used to update, evaluate, and modify boundary conditions used by the earlier ground-water flow model. The model was updated using the USGS finite-difference code MODFLOW-2000 for mean-annual conditions during 1987-92 and 2002. The specified heads in the source-sink layer A1 were lowered to reflect observed water-level declines during the 1998-2002 drought. These declines resulted in a decrease of 12.1 million gallons per day (Mgal/d) in simulated recharge or vertical inflow to the uppermost confined aquifer (Gordon, layer A2). Although ground-water pumpage in the study area has increased by 32 Mgal/d since 1995, most of this increase (17.5 Mgal/d) was from the unconfined Upper Three Runs aquifer (source-sink layer A1) with the remaining 14.5 Mgal/d assigned to the active layers within the model (A2-A7). The simulated water budget for 2002 shows a decrease from the 1987-92 model from 1,040 Mgal/d to 1,035 Mgal/d. The decreased ground-water inflows and increased ground-water withdrawal rates reduced the simulated ground-water outflow to river cells in the active layers of the model by 43 Mgal/d. The calibration statistics for all layers of the 2002 simulation resulted in a decrease in the root mean square

  17. Climate reconstruction from borehole temperatures influenced by groundwater flow

    Science.gov (United States)

    Kurylyk, B.; Irvine, D. J.; Tang, W.; Carey, S. K.; Ferguson, G. A. G.; Beltrami, H.; Bense, V.; McKenzie, J. M.; Taniguchi, M.

    2017-12-01

    Borehole climatology offers advantages over other climate reconstruction methods because further calibration steps are not required and heat is a ubiquitous subsurface property that can be measured from terrestrial boreholes. The basic theory underlying borehole climatology is that past surface air temperature signals are reflected in the ground surface temperature history and archived in subsurface temperature-depth profiles. High frequency surface temperature signals are attenuated in the shallow subsurface, whereas low frequency signals can be propagated to great depths. A limitation of analytical techniques to reconstruct climate signals from temperature profiles is that they generally require that heat flow be limited to conduction. Advection due to groundwater flow can thermally `contaminate' boreholes and result in temperature profiles being rejected for regional climate reconstructions. Although groundwater flow and climate change can result in contrasting or superimposed thermal disturbances, groundwater flow will not typically remove climate change signals in a subsurface thermal profile. Thus, climate reconstruction is still possible in the presence of groundwater flow if heat advection is accommodated in the conceptual and mathematical models. In this study, we derive a new analytical solution for reconstructing surface temperature history from borehole thermal profiles influenced by vertical groundwater flow. The boundary condition for the solution is composed of any number of sequential `ramps', i.e. periods with linear warming or cooling rates, during the instrumented and pre-observational periods. The boundary condition generation and analytical temperature modeling is conducted in a simple computer program. The method is applied to reconstruct climate in Winnipeg, Canada and Tokyo, Japan using temperature profiles recorded in hydrogeologically active environments. The results demonstrate that thermal disturbances due to groundwater flow and climate

  18. A Guide for Using the Transient Ground-Water Flow Model of the Death Valley Regional Ground-Water Flow System, Nevada and California

    Energy Technology Data Exchange (ETDEWEB)

    Joan B. Blainey; Claudia C. Faunt, and Mary C. Hill

    2006-05-16

    This report is a guide for executing numerical simulations with the transient ground-water flow model of the Death Valley regional ground-water flow system, Nevada and California using the U.S. Geological Survey modular finite-difference ground-water flow model, MODFLOW-2000. Model inputs, including observations of hydraulic head, discharge, and boundary flows, are summarized. Modification of the DVRFS transient ground-water model is discussed for two common uses of the Death Valley regional ground-water flow system model: predictive pumping scenarios that extend beyond the end of the model simulation period (1998), and model simulations with only steady-state conditions.

  19. HYDRASTAR - a code for stochastic simulation of groundwater flow

    International Nuclear Information System (INIS)

    Norman, S.

    1992-05-01

    The computer code HYDRASTAR was developed as a tool for groundwater flow and transport simulations in the SKB 91 safety analysis project. Its conceptual ideas can be traced back to a report by Shlomo Neuman in 1988, see the reference section. The main idea of the code is the treatment of the rock as a stochastic continuum which separates it from the deterministic methods previously employed by SKB and also from the discrete fracture models. The current report is a comprehensive description of HYDRASTAR including such topics as regularization or upscaling of a hydraulic conductivity field, unconditional and conditional simulation of stochastic processes, numerical solvers for the hydrology and streamline equations and finally some proposals for future developments

  20. Developing an Analysis Program to Estimate and Prediction Groundwater Droughts in Korea from Groundwater Time-Series Data.

    Science.gov (United States)

    Cho, S.; Woo, N. C.; Lee, J. M.

    2015-12-01

    This study is aimed at developing process to analyze and predict groundwater drought potentials for Winter and Spring droughts in Korea using a long-term groundwater monitoring data. So far, most drought researches have been focused on precipitation and stream-flow data, although these data are considered to be non-linear. Subsequently, the prediction of drought events has been very difficult in practice. In this study, we targets to analyze the groundwater system as an intermediate stage between precipitation and stream-flow, but still has semi-linear characteristics. By the analysis of past trends of groundwater time-series compared with drought events, we will identify characteristics of fluctuation between groundwater-level and precipitation of the year before the droughts. Then, the characteristics will be tested with recent drought events in Korea. For this analysis, The updated ATGT (Analysis Tool for Groundwater Time-series data program version 1.0 based on JAVA), that was developed for analyzing and presenting groundwater time-series data, basically to identify abnormal changes in groundwater fluctuations, will be presented with additional functions including cross-correlation between groundwater and drought based on the PYTHON language.

  1. Indications of regional scale groundwater flows in the Amazon Basins: Inferences from results of geothermal studies

    Science.gov (United States)

    Pimentel, Elizabeth T.; Hamza, Valiya M.

    2012-08-01

    The present work deals with determination groundwater flows in the Amazon region, based on analysis of geothermal data acquired in shallow and deep wells. The method employed is based on the model of simultaneous heat transfer by conduction and advection in permeable media. Analysis of temperature data acquired in water wells indicates down flows of groundwaters with velocities in excess of 10-7 m/s at depths less than 300 m in the Amazonas basin. Bottom-hole temperature (BHT) data sets have been used in determining characteristics of fluid movements at larger depths in the basins of Acre, Solimões, Amazonas, Marajó and Barreirinhas. The results of model simulations point to down flow of groundwaters with velocities of the order of 10-8 to 10-9 m/s, at depths of up to 4000 m. No evidence has been found for up flow typical of discharge zones. The general conclusion compatible with such results is that large-scale groundwater recharge systems operate at both shallow and deep levels in all sedimentary basins of the Amazon region. However, the basement rock formations of the Amazon region are relatively impermeable and hence extensive down flow systems through the sedimentary strata are possible only in the presence of generalized lateral movement of groundwater in the basal parts of the sedimentary basins. The direction of this lateral flow, inferred from the basement topography and geological characteristics of the region, is from west to east, following roughly the course of surface drainage system of the Amazon River, with eventual discharge into the Atlantic Ocean. The estimated flow rate at the continental margin is 3287 m3/s, with velocities of the order of 218 m/year. It is possible that dynamic changes in the fluvial systems in the western parts of South American continent have been responsible for triggering alterations in the groundwater recharge systems and deep seated lateral flows in the Amazon region.

  2. Groundwater recharge and flow on Montserrat, West Indies: Insights from groundwater dating

    OpenAIRE

    Hemmings, Brioch; Gooddy, Daren; Whitaker, Fiona; George Darling, W.; Jasim, Alia; Gottsmann, Joachim

    2015-01-01

    Study region Montserrat, Lesser Antilles, Caribbean. Study focus Analysis of δ2H and δ18O isotopes, and chlorofluorocarbon (CFC) anthropogenic tracers in Montserrat groundwater provides insights into the age and provenance of the spring waters. New hydrological insights δ2H and δ18O analysis indicates uniform recharge elevations for groundwaters on Montserrat. CFC-11 and CFC-12 analysis reveals age differences between isotopically similar, high elevation springs and low eleva...

  3. Determination of groundwater flow velocity by radon measurements

    International Nuclear Information System (INIS)

    Hohn, E.; von Gunten, H.R.

    1990-01-01

    The groundwater resources of glacio-fluvial perialpine valleys are recharged significantly by the infiltration from rivers. The groundwater residence times between rivers and wells should be known in groundwater management problems. Short residence times can be estimated using radon. Radon concentrations in rivers are usually very low. Upon filtration and movement of the water in the ground, radon is picked up and its concentration increases by 2-3 orders of magnitude according to radioactive growth laws. Residence times and flow velocities can be estimated from the increasing radon concentrations measured in groundwater sampling tubes at different distances from the river. Results obtained with this method agree with the results from experiments with artificial tracers

  4. Fractal scaling analysis of groundwater dynamics in confined aquifers

    Science.gov (United States)

    Tu, Tongbi; Ercan, Ali; Kavvas, M. Levent

    2017-10-01

    Groundwater closely interacts with surface water and even climate systems in most hydroclimatic settings. Fractal scaling analysis of groundwater dynamics is of significance in modeling hydrological processes by considering potential temporal long-range dependence and scaling crossovers in the groundwater level fluctuations. In this study, it is demonstrated that the groundwater level fluctuations in confined aquifer wells with long observations exhibit site-specific fractal scaling behavior. Detrended fluctuation analysis (DFA) was utilized to quantify the monofractality, and multifractal detrended fluctuation analysis (MF-DFA) and multiscale multifractal analysis (MMA) were employed to examine the multifractal behavior. The DFA results indicated that fractals exist in groundwater level time series, and it was shown that the estimated Hurst exponent is closely dependent on the length and specific time interval of the time series. The MF-DFA and MMA analyses showed that different levels of multifractality exist, which may be partially due to a broad probability density distribution with infinite moments. Furthermore, it is demonstrated that the underlying distribution of groundwater level fluctuations exhibits either non-Gaussian characteristics, which may be fitted by the Lévy stable distribution, or Gaussian characteristics depending on the site characteristics. However, fractional Brownian motion (fBm), which has been identified as an appropriate model to characterize groundwater level fluctuation, is Gaussian with finite moments. Therefore, fBm may be inadequate for the description of physical processes with infinite moments, such as the groundwater level fluctuations in this study. It is concluded that there is a need for generalized governing equations of groundwater flow processes that can model both the long-memory behavior and the Brownian finite-memory behavior.

  5. Fractal scaling analysis of groundwater dynamics in confined aquifers

    Directory of Open Access Journals (Sweden)

    T. Tu

    2017-10-01

    Full Text Available Groundwater closely interacts with surface water and even climate systems in most hydroclimatic settings. Fractal scaling analysis of groundwater dynamics is of significance in modeling hydrological processes by considering potential temporal long-range dependence and scaling crossovers in the groundwater level fluctuations. In this study, it is demonstrated that the groundwater level fluctuations in confined aquifer wells with long observations exhibit site-specific fractal scaling behavior. Detrended fluctuation analysis (DFA was utilized to quantify the monofractality, and multifractal detrended fluctuation analysis (MF-DFA and multiscale multifractal analysis (MMA were employed to examine the multifractal behavior. The DFA results indicated that fractals exist in groundwater level time series, and it was shown that the estimated Hurst exponent is closely dependent on the length and specific time interval of the time series. The MF-DFA and MMA analyses showed that different levels of multifractality exist, which may be partially due to a broad probability density distribution with infinite moments. Furthermore, it is demonstrated that the underlying distribution of groundwater level fluctuations exhibits either non-Gaussian characteristics, which may be fitted by the Lévy stable distribution, or Gaussian characteristics depending on the site characteristics. However, fractional Brownian motion (fBm, which has been identified as an appropriate model to characterize groundwater level fluctuation, is Gaussian with finite moments. Therefore, fBm may be inadequate for the description of physical processes with infinite moments, such as the groundwater level fluctuations in this study. It is concluded that there is a need for generalized governing equations of groundwater flow processes that can model both the long-memory behavior and the Brownian finite-memory behavior.

  6. Detect groundwater flowing from riverbed using a drone

    Science.gov (United States)

    Kato, Kenji; Takemon, Yasuhiro

    2017-04-01

    Estimate the direct flow of groundwater to river is an important step in understanding of hydrodynamics in river system. Function of groundwater in river system does not limit to the mass of water. Continuous supply with thermally stable water from riverbed produces a space with unique condition, which provides various functions for organisms inhabiting in river as a shelter avoiding large shift of temperature, or to maintain productivity for small scale ecosystem by supplying nutrient rich groundwater if it gushes out from the riverbed in a deep pool of river. This may contribute to biodiversity of river system. Such function of groundwater is more significant for rivers run in island and in mountain zone. To evaluate the function of groundwater flowing from riverbed we first try to find such site by using a drone equipped with a sensitive thermo-camera to detect water surface temperature. In the examined area temperature of the groundwater doesn't change much throughout a year at around 15 to 16 °C, while surface temperature of the examined river fluctuates from below 10 °C to over 25 °C throughout seasons. By using this difference in temperature between groundwater and river water we tried to find site where groundwater comes out from the riverbed. Obviously winter when surface temperature becomes below 10 °C is an appropriate season to find groundwater as it comes up to the surface of river with depth ranging from 1 to 3 m. Trial flight surveys of drone were conducted in Kano-river in Izu Peninsula located at southern foot of Mt. Fuji in central Japan. Employed drone was Inspire1 (DJI, China) equipped with a Thermal camera (Zenmuse XT ZXTA 19 FP, FLIR, USA) and operated by Kazuhide Juta (KELEK Co. Ltd., Japan) and Mitsuhiro Komiya (TAM.Co.,LTD). In contrast to the former cases with employing airplane for taking aerial photograph, drone takes photo while flying at a low-altitude. When it flies at 40m above the water surface of river, resolution is at an

  7. Simulation of groundwater flow and interaction of groundwater and surface water on the Lac du Flambeau Reservation, Wisconsin

    Science.gov (United States)

    Juckem, Paul F.; Fienen, Michael N.; Hunt, Randall J.

    2014-01-01

    The Lac du Flambeau Band of Lake Superior Chippewa and Indian Health Service are interested in improving the understanding of groundwater flow and groundwater/surface-water interaction on the Lac du Flambeau Reservation (Reservation) in southwest Vilas County and southeast Iron County, Wisconsin, with particular interest in an understanding of the potential for contamination of groundwater supply wells and the fate of wastewater that is infiltrated from treatment lagoons on the Reservation. This report describes the construction, calibration, and application of a regional groundwater flow model used to simulate the shallow groundwater flow system of the Reservation and water-quality results for groundwater and surface-water samples collected near a system of waste-water-treatment lagoons. Groundwater flows through a permeable glacial aquifer that ranges in thickness from 60 to more than 200 feet (ft). Seepage and drainage lakes are common in the area and influence groundwater flow patterns on the Reservation. A two-dimensional, steady-state analytic element groundwater flow model was constructed using the program GFLOW. The model was calibrated by matching target water levels and stream base flows through the use of the parameter-estimation program, PEST. Simulated results illustrate that groundwater flow within most of the Reservation is toward the Bear River and the chain of lakes that feed the Bear River. Results of analyses of groundwater and surface-water samples collected downgradient from the wastewater infiltration lagoons show elevated levels of ammonia and dissolved phosphorus. In addition, wastewater indicator chemicals detected in three downgradient wells and a small downgradient stream indicate that infiltrated wastewater is moving southwest of the lagoons toward Moss Lake. Potential effects of extended wet and dry periods (within historical ranges) were evaluated by adjusting precipitation and groundwater recharge in the model and comparing the

  8. Shallow groundwater in the Matanuska-Susitna Valley, Alaska—Conceptualization and simulation of flow

    Science.gov (United States)

    Kikuchi, Colin P.

    2013-01-01

    The Matanuska-Susitna Valley is in the Upper Cook Inlet Basin and is currently undergoing rapid population growth outside of municipal water and sewer service areas. In response to concerns about the effects of increasing water use on future groundwater availability, a study was initiated between the Alaska Department of Natural Resources and the U.S. Geological Survey. The goals of the study were (1) to compile existing data and collect new data to support hydrogeologic conceptualization of the study area, and (2) to develop a groundwater flow model to simulate flow dynamics important at the regional scale. The purpose of the groundwater flow model is to provide a scientific framework for analysis of regional-scale groundwater availability. To address the first study goal, subsurface lithologic data were compiled into a database and were used to construct a regional hydrogeologic framework model describing the extent and thickness of hydrogeologic units in the Matanuska-Susitna Valley. The hydrogeologic framework model synthesizes existing maps of surficial geology and conceptual geochronologies developed in the study area with the distribution of lithologies encountered in hundreds of boreholes. The geologic modeling package Geological Surveying and Investigation in Three Dimensions (GSI3D) was used to construct the hydrogeologic framework model. In addition to characterizing the hydrogeologic framework, major groundwater-budget components were quantified using several different techniques. A land-surface model known as the Deep Percolation Model was used to estimate in-place groundwater recharge across the study area. This model incorporates data on topography, soils, vegetation, and climate. Model-simulated surface runoff was consistent with observed streamflow at U.S. Geological Survey streamgages. Groundwater withdrawals were estimated on the basis of records from major water suppliers during 2004-2010. Fluxes between groundwater and surface water were

  9. The effects of radiogenic heat on groundwater flow

    International Nuclear Information System (INIS)

    Beddoes, R.J.; Tammemagi, H.Y.

    1986-03-01

    The effects of radiogenic heat released by a nuclear waste repository on the groundwater flow in the neighbouring rock mass is reviewed. The report presents an overview of the hydrogeologic properties of crystalline rocks in the Canadian Shield and also describes the mathematical theory of groundwater flow and heat transfer in both porous media and fractured rock. Numerical methods for the solution of the governing equations are described. A number of case histories are described where analyses of flow systems have been performed both with and without radiogenic heat sources. A number of relevant topics are reviewed such as the role of the porous medium model, boundary conditions and, most importantly, the role of complex coupled processes where the effects of heat and water flow are intertwined with geochemical and mechanical processes. The implications to radioactive waste disposal are discussed

  10. Calibration of a groundwater flow and contaminant transport computer model: Progress toward model validation

    International Nuclear Information System (INIS)

    Lee, R.R.; Ketelle, R.H.; Bownds, J.M.; Rizk, T.A.

    1989-09-01

    A groundwater flow and contaminant transport model calibration was performed to evaluate the ability of a typical, verified computer code to simulate groundwater tracer migration in the shallow aquifer of the Conasauga Group. Previously, standard practice site data interpretation and groundwater modeling resulted in inaccurate simulations of contaminant transport direction and rate compared with tracer migration behavior. The site's complex geology, the presence of flow in both fractured and weathered zones, and the transient character of flow in the shallow aquifer combined to render inaccurate assumptions of steady-state, homogeneous groundwater flow. The improvement of previous modeling results required iterative phases of conceptual model development, hypothesis testing, site field investigations, and modeling. The activities focused on generating a model grid that was compatible with site hydrogeologic conditions and on establishing boundary conditions based on site data. An annual average water table configuration derived from site data and fixed head boundary conditions was used as input for flow modeling. The contaminant transport model was combined with the data-driven flow model to obtain a preliminary contaminant plume. Calibration of the transport code was achieved by comparison with site tracer migration and concentration data. This study documents the influence of fractures and the transient character of flow and transport in the shallow aquifer. Although compatible with porous medium theory, site data demonstrate that the tracer migration pathway would not be anticipated using conventional porous medium analysis. 126 figs., 22 refs., 5 tabs

  11. Groundwater flow model and its implications for contaminant behavior

    African Journals Online (AJOL)

    What sets hydrogeology apart from many of the other geosciences is an emphasis on treating problems mathematically. The mathematical approach involves representing a groundwater process by an equation and solving that equation. These equations are fundamental to the quantitative treatment of flow and provide the ...

  12. Numerical modelling of groundwater flow to understand the impacts ...

    Indian Academy of Sciences (India)

    @hotmail.com. In this paper, numerical simulations of regional-scale groundwater flow of North Bengal Plain have been carried out with special emphasis on the arsenic (As)-rich alluvium filled gap between the Rajmahal hills on the west and ...

  13. Effects of geological structures on groundwater flow and quality in ...

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Earth System Science; Volume 124; Issue 2. Effects of geological structures on groundwater flow and quality in hardrock regions of northern Tirunelveli district, southern India. M Senthilkumar R Arumugam D Gnanasundar D S C Thambi E Sampath Kumar. Volume 124 Issue 2 March 2015 pp ...

  14. Numerical modelling of groundwater flow to understand the impacts ...

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Earth System Science; Volume 126; Issue 2. Numerical modelling of groundwater flow to understand the impacts of pumping on arsenic migration in the aquifer of North Bengal Plain. P K Sikdar Surajit Chakraborty. Volume 126 Issue 2 March 2017 Article ID 29 ...

  15. Spatial Scheme for Groundwater Flow and Physical Properties ...

    African Journals Online (AJOL)

    Spatial flow patterns and quality trends for groundwater in Southwestern Nigeria have been undertaken with inadequate depth of interpretation. In this study, the geographical locations of wells and respective elevation were recorded using a Global Positioning System (GPS). Well depth and water level measurements were ...

  16. Numerical modelling of groundwater flow to understand the impacts ...

    Indian Academy of Sciences (India)

    c Indian Academy of Sciences. DOI 10.1007/s12040-017-0799-x. Numerical modelling of groundwater flow to understand the impacts of pumping on arsenic migration in the aquifer of North Bengal Plain. P K Sikdar∗ and Surajit Chakraborty. Department of Environment Management, Indian Institute of Social Welfare and.

  17. Modeling of groundwater flow for Mujib aquifer, Jordan

    Indian Academy of Sciences (India)

    Home; Journals; Journal of Earth System Science; Volume 115; Issue 3. Modeling of groundwater flow for Mujib aquifer, ... Associate Professor of Water Resources, Civil Engineering Department, Jordan University of Science & Technology, P.O Box 3030, Irbid 22110, Jordan. Water Resources Consultant, Eco-Consult, ...

  18. Radioisotope tracer application in surface and groundwater flow measurements

    International Nuclear Information System (INIS)

    Monev, E.

    1983-01-01

    The ''peak to peak'' method for measurement of water flow with the use of radioactive tracer was investigated. The theoretical basis for this method has been established. The experiments in the open channel have shown the applicability of the method. Groundwater flow was studied by injection of radioactive tracer into the bore-hole followed by gamma-logging in three different time intervals. Interpretation of gamma lows in terms of filtration velocity in various depths proved to be possible

  19. Hydrodynamic analysis of potential groundwater extraction capacity increase: case study of 'Nelt' groundwater source at Dobanovci

    Directory of Open Access Journals (Sweden)

    Bajić Dragoljub I.

    2017-01-01

    Full Text Available A comprehensive hydrodynamic analysis of the groundwater regime undertaken to assess the potential for expanding the 'Nelt' groundwater source at Dobanovci, or developing a new groundwater source for a future baby food factory, including the quantification of the impact on the production wells of the nearby 'Pepsi' groundwater source, is presented in the paper. The existing Nelt source is comprised of three active production wells that tap a subartesian aquifer formed in sands and gravelly sands; however, the analysis considers only the two nearest wells. A long-term group pumping test was con-ducted of production wells N-1 and N2 (Nelt source and production wells B-1 and B-2 (Pepsi source, while the piezometric head in the vicinity of these wells was monitored at observation well P-1, which is located in the area considered for Nelt source expansion. Data were collected at maximum pumping capacity of all the production wells. A hydrodynamic model of groundwater flow in the extended area of the Nelt source was generated for the purposes of the comprehensive hydrodynamic analysis. Hydrodynamic prognostic calculations addressed two solution alternatives for the capacity increase over a period of ten years. Licensed Visual MODFLOW Pro software, deemed to be at the very top in this field, was used for the calculations.

  20. Very deep hole concept. Thermal effects on groundwater flow

    Energy Technology Data Exchange (ETDEWEB)

    Marsic, Niko; Grundfelt, Bertil; Wiborgh, Marie [Kemakta Konsult AB, Stockholm (Sweden)

    2006-09-15

    ,055 nodes. The results of the calculations were evaluated using tracking of particle starting in different positions in the deposition holes. The travel times for these particles to the surface were calculated. The particle tracking was performed for individual time steps assuming that the conditions of that time step remained constant throughout the particle travel times. This is of course not true, in particular as the calculated travel times are much longer that the duration of the heat pulse from the deposited spent fuel. A more refined variant of the grid including 1,245,680 finite elements corresponding to 2,525,744 nodes was tested in order to verify that the discretisation used was adequate. In this case, all elements inside the repository area and those closest to this area were refined by a factor of two in each of the three dimensions. The elements constituting the boreholes were left unchanged. The results of this test show that both the flow pattern and the calculated Darcy velocities are significantly affected by the disretisation while the calculated particle travel times were little influenced. Because of the little difference of travel times and due to the fact that the computational times of the larger grid were hard to manage within a reasonable project schedule, it was decided to use the smaller grid for the calculations. A large number of calculations were performed in which the sensitivity of the results with respect to different combinations of surface hydraulic gradients, heat output from the deposited spent fuel and fracture zone orientations was tested. In general, the calculated travel times for the particles are extremely long, in the order of 1-100 Myrs. The thermal output from the spent fuel is insufficient to alter the stability of the near-stagnant saline groundwater present at depth in the rock. However, the performed sensitivity analysis showed effects on the Darcy velocities, flow field and calculated hypothetical travel times, but the

  1. Structural Controls on Groundwater Flow in Basement Terrains: Geophysical, Remote Sensing, and Field Investigations in Sinai

    KAUST Repository

    Mohamed, Lamees

    2015-07-09

    An integrated [very low frequency (VLF) electromagnetic, magnetic, remote sensing, field, and geographic information system (GIS)] study was conducted over the basement complex in southern Sinai (Feiran watershed) for a better understanding of the structural controls on the groundwater flow. The increase in satellite-based radar backscattering values following a large precipitation event (34 mm on 17–18 January 2010) was used to identify water-bearing features, here interpreted as preferred pathways for surface water infiltration. Findings include: (1) spatial analysis in a GIS environment revealed that the distribution of the water-bearing features (conductive features) corresponds to that of fractures, faults, shear zones, dike swarms, and wadi networks; (2) using VLF (43 profiles), magnetic (7 profiles) techniques, and field observations, the majority (85 %) of the investigated conductive features were determined to be preferred pathways for groundwater flow; (3) northwest–southeast- to north–south-trending conductive features that intersect the groundwater flow (southeast to northwest) at low angles capture groundwater flow, whereas northeast–southwest to east–west features that intersect the flow at high angles impound groundwater upstream and could provide potential productive well locations; and (4) similar findings are observed in central Sinai: east–west-trending dextral shear zones (Themed and Sinai Hinge Belt) impede south to north groundwater flow as evidenced by the significant drop in hydraulic head (from 467 to 248 m above mean sea level) across shear zones and by reorientation of regional flow (south–north to southwest–northeast). The adopted integrated methodologies could be readily applied to similar highly fractured basement arid terrains elsewhere. © 2015 Springer Science+Business Media Dordrecht

  2. Groundwater availability as constrained by hydrogeology and environmental flows.

    Science.gov (United States)

    Watson, Katelyn A; Mayer, Alex S; Reeves, Howard W

    2014-01-01

    Groundwater pumping from aquifers in hydraulic connection with nearby streams has the potential to cause adverse impacts by decreasing flows to levels below those necessary to maintain aquatic ecosystems. The recent passage of the Great Lakes-St. Lawrence River Basin Water Resources Compact has brought attention to this issue in the Great Lakes region. In particular, the legislation requires the Great Lakes states to enact measures for limiting water withdrawals that can cause adverse ecosystem impacts. This study explores how both hydrogeologic and environmental flow limitations may constrain groundwater availability in the Great Lakes Basin. A methodology for calculating maximum allowable pumping rates is presented. Groundwater availability across the basin may be constrained by a combination of hydrogeologic yield and environmental flow limitations varying over both local and regional scales. The results are sensitive to factors such as pumping time, regional and local hydrogeology, streambed conductance, and streamflow depletion limits. Understanding how these restrictions constrain groundwater usage and which hydrogeologic characteristics and spatial variables have the most influence on potential streamflow depletions has important water resources policy and management implications. © 2013, National Ground Water Association.

  3. Approaches to the simulation of unconfined flow and perched groundwater flow in MODFLOW

    Science.gov (United States)

    Bedekar, Vivek; Niswonger, Richard G.; Kipp, Kenneth; Panday, Sorab; Tonkin, Matthew

    2012-01-01

    Various approaches have been proposed to manage the nonlinearities associated with the unconfined flow equation and to simulate perched groundwater conditions using the MODFLOW family of codes. The approaches comprise a variety of numerical techniques to prevent dry cells from becoming inactive and to achieve a stable solution focused on formulations of the unconfined, partially-saturated, groundwater flow equation. Keeping dry cells active avoids a discontinuous head solution which in turn improves the effectiveness of parameter estimation software that relies on continuous derivatives. Most approaches implement an upstream weighting of intercell conductance and Newton-Raphson linearization to obtain robust convergence. In this study, several published approaches were implemented in a stepwise manner into MODFLOW for comparative analysis. First, a comparative analysis of the methods is presented using synthetic examples that create convergence issues or difficulty in handling perched conditions with the more common dry-cell simulation capabilities of MODFLOW. Next, a field-scale three-dimensional simulation is presented to examine the stability and performance of the discussed approaches in larger, practical, simulation settings.

  4. The in situ permeable flow sensor: A device for measuring groundwater flow velocity

    International Nuclear Information System (INIS)

    Ballard, S.; Barker, G.T.; Nichols, R.L.

    1994-03-01

    A new technology called the In Situ Permeable Flow Sensor has been developed at Sandia National Laboratories. These sensors use a thermal perturbation technique to directly measure the direction and magnitude of the full three dimensional groundwater flow velocity vector in unconsolidated, saturated, porous media. The velocity measured is an average value characteristic of an approximately 1 cubic meter volume of the subsurface. During a test at the Savannah River Site in South Carolina, two flow sensors were deployed in a confined aquifer in close proximity to a well which was screened over the entire vertical extent of the aquifer and the well was pumped at four different pumping rates. In this situation horizontal flow which is radially directed toward the pumping well is expected. The flow sensors measured horizontal flow which was directed toward the pumping well, within the uncertainty in the measurements. The observed magnitude of the horizontal component of the flow velocity increased linearly with pumping rate, as predicted by theoretical considerations. The measured horizontal component of the flow velocity differed from the predicted flow velocity, which was calculated with the assumptions that the hydraulic properties of the aquifer were radially homogeneous and isotropic, by less than a factor of two. Drawdown data obtained from other wells near the pumping well during the pump test indicate that the hydraulic properties of the aquifer are probably not radially homogeneous but the effect of the inhomogeneity on the flow velocity field around the pumping well was not modeled because the degree and distribution of the inhomogeneity are unknown. Grain size analysis of core samples from wells in the area were used to estimate the vertical distribution of hydraulic conductivity

  5. The fractional Boussinesq equation of groundwater flow and its applications

    Science.gov (United States)

    Su, Ninghu

    2017-04-01

    This paper presents a set of fractional Boussinesq equations (fBEs) for groundwater flow in confined and unconfined aquifers and demonstrates the application of one of the fBEs for groundwater discharges known as recession curves. The fBEs are formulated with two-term distributed fractional orders in time and symmetrical fractional derivatives (SFD) in space applicable to both confined and unconfined aquifers. The SFD in theory consists of the forward fractional derivative (FFD) and the backward fractional derivative (BFD). The FFD represents the forward movement of water along the direction of mainstream flow while the BFD accounts for the backward motion of water in the direction opposite to the mainstream flow. The backward flow at the pore level can be referred to as the micro-scale backwater effect. The analogue of the backwater effect on a micro-scale using the BFD coincides with the wandering processes based on the continuous-time random walk (CTRW) theory which results in the fractional governing equation. With the analytical solutions of the fBE for given initial and boundary conditions of the first type for a finite depth, a set of formulae for groundwater recession has been derived using approximate solutions of the fBE. The examples of the applications of the recession curves are graphically illustrated and the effects of the orders of fractional derivatives on the geometry of the flow curves examined.

  6. Effect of land use and groundwater flow path on submarine groundwater discharge nutrient flux

    Directory of Open Access Journals (Sweden)

    James M. Bishop

    2017-06-01

    New hydrological insights for the region: Low nitrate + nitrite (N + N SGD fluxes (24 mols/d were measured where groundwater flowed beneath primarily undeveloped land on transit to the coast. By contrast, of all land use types, sugarcane and pineapple fields contributed the largest amount of N to coastal waters via SGD (3800 mols/d. Despite their much smaller freshwater flux, these SGD sources provide substantially larger N fluxes than the State's largest rivers (avg. 700 mols/d. Septic systems, cesspools, and near coast wastewater injection wells also contribute N + N to groundwater and coastal waters, although in much smaller quantities. This study demonstrates that numerical groundwater modeling combined with geochemical modeling can be used to determine sources and flux of nutrients in SGD and provides a unique, original, and practical framework for studying the effect of land use and its impact on nutrient delivery to coastal waters.

  7. Incorporating groundwater flow into the WEPP model

    Science.gov (United States)

    William Elliot; Erin Brooks; Tim Link; Sue Miller

    2010-01-01

    The water erosion prediction project (WEPP) model is a physically-based hydrology and erosion model. In recent years, the hydrology prediction within the model has been improved for forest watershed modeling by incorporating shallow lateral flow into watershed runoff prediction. This has greatly improved WEPP's hydrologic performance on small watersheds with...

  8. Simulation of Ground-Water Flow and Effects of Ground-Water Irrigation on Base Flow in the Elkhorn and Loup River Basins, Nebraska

    Science.gov (United States)

    Peterson, Steven M.; Stanton, Jennifer S.; Saunders, Amanda T.; Bradley, Jesse R.

    2008-01-01

    ground-water irrigation on stream base flow for 1940 through 2005 and for 2006 through 2045. Simulated base flows were compared for scenarios that alternately did or did not include a representation of the effects of ground-water irrigation. The difference between simulated base flows for the two scenarios represents the predicted effects of ground-water irrigation on base flow. Comparison of base flows between simulations with ground-water irrigation and no ground-water irrigation indicated that ground-water irrigation has cumulatively reduced streamflows from 1940 through 2005 by 888,000 acre-feet in the Elkhorn River Basin and by 2,273,000 acre-feet in the Loup River Basin. Generally, predicted cumulative effects of ground-water irrigation on base flow were 5 to 10 times larger from 2006 through 2045 than from 1940 through 2005, and were 7,678,000 acre-feet for the Elkhorn River Basin and 14,784,000 acre-feet for the Loup River Basin. The calibrated simulation also was used to estimate base-flow depletion as a percentage of pumping volumes for a 50-year future time period, because base-flow depletion percentages are used to guide the placement of management boundaries in Nebraska. Mapped results of the base-flow depletion analysis conducted for most of the interior of the study area indicated that pumpage of one additional theoretical well simulated for a future 50-year period generally would result in more than 80 percent depletion when it was located close to the stream, except in areas where depletion was partly offset by reduced ground-water discharge to evapotranspiration in wetland areas. In many areas, depletion for the 50-year future period composed greater than 10 percent of the pumped water volume for theoretical wells placed less than 7 or 8 miles from the stream, though considerable variations existed because of the heterogeneity of the natural system represented in the simulation. For a few streams, predicted future simulated base flows dec

  9. Groundwater flow modelling at the Olkiluoto site, Finland

    International Nuclear Information System (INIS)

    Loefman, J.

    1996-01-01

    Preliminary site investigations for spent fuel disposal has been carried out at the Olkiluoto site, Finland. During the investigations high salt concentrations were measured in the groundwater samples deep in the bedrock. In this study, the groundwater flow is analyzed at Olkiluoto taking into account the effects of salinity. The transient simulations are performed by solving coupled and non-linear partial differential equations describing the flow and solute transport. A site-specific simulation model for flow and transport is developed on the basis of the field investigations. The simulations are carried out for a period that started when the highest hills at Olkiluoto rose above sea level. The simulation period continues until the present day. The results of the coupled simulations were strongly dependent on the poorly known initial salinity distribution in the solution domain. The DP approximation together with the EC approximation proved to be a useful complementary approach when simulating solute transport in a fractured rock mass. The simulations also confirm the assumption that the realistic simulation of groundwater flow at Olkiluoto requires taking into account the effects of salinity

  10. Detecting influential observations in nonlinear regression modeling of groundwater flow

    Science.gov (United States)

    Yager, Richard M.

    1998-01-01

    Nonlinear regression is used to estimate optimal parameter values in models of groundwater flow to ensure that differences between predicted and observed heads and flows do not result from nonoptimal parameter values. Parameter estimates can be affected, however, by observations that disproportionately influence the regression, such as outliers that exert undue leverage on the objective function. Certain statistics developed for linear regression can be used to detect influential observations in nonlinear regression if the models are approximately linear. This paper discusses the application of Cook's D, which measures the effect of omitting a single observation on a set of estimated parameter values, and the statistical parameter DFBETAS, which quantifies the influence of an observation on each parameter. The influence statistics were used to (1) identify the influential observations in the calibration of a three-dimensional, groundwater flow model of a fractured-rock aquifer through nonlinear regression, and (2) quantify the effect of omitting influential observations on the set of estimated parameter values. Comparison of the spatial distribution of Cook's D with plots of model sensitivity shows that influential observations correspond to areas where the model heads are most sensitive to certain parameters, and where predicted groundwater flow rates are largest. Five of the six discharge observations were identified as influential, indicating that reliable measurements of groundwater flow rates are valuable data in model calibration. DFBETAS are computed and examined for an alternative model of the aquifer system to identify a parameterization error in the model design that resulted in overestimation of the effect of anisotropy on horizontal hydraulic conductivity.

  11. Groundwater flow in an intermountain basin: Hydrological, geophysical, and geological exploration of South Park, Colorado

    Science.gov (United States)

    Ball, Lyndsay Brooke

    Groundwater in the intermountain basins of the American West is increasingly of interest with respect to water supply, ecosystem integrity, and contaminant and heat transport processes. These basins are defined by their heterogeneity through large topographic relief, substantial climatic variability, and permeability distributions made complex through variations in lithology and deformation over the orogenic history of these regions, leading to folded and faulted aquifers. This dissertation focuses on the influence of these heterogeneities on the groundwater flow system of the South Park basin in central Colorado, USA. The influence of faults on shallow groundwater flow was examined at two locations along the mapped trace of the Elkhorn fault, a Laramide reverse fault that juxtaposes crystalline and sedimentary rocks in eastern South Park. At the first location, electromagnetic, resistivity, self-potential, and hydraulic data were collected at an existing well field straddling the fault trace. Integrated analysis suggested the fault behaves as combined conduit barrier to groundwater in flow the upper 60 m. A second location along the mapped trace was selected through additional geophysical exploration. New boreholes were drilled to make direct geologic, hydrologic, and geophysical observations of the fault zone. However, these boreholes did not intersect the Elkhorn fault despite passing through rocks with similar electrical resistivity signatures to the first study location. Analyses of drill core and geophysical data indicate that the mineralogical composition of the crystalline rocks strongly influences their resistivity values, and the resistivity contrasts associated with the rock juxtaposition created by the Elkhorn fault is not unique. A steady-state, three-dimensional groundwater flow model of the South Park basin was developed to explore the influence of complex topography, recharge, and permeability structure on regional groundwater flow. Geologic

  12. Application of mathematical model for simulation of groundwater flow

    International Nuclear Information System (INIS)

    Carvalho Filho, Carlos Alberto de; Branco, Otavio Eurico de Aquino; Loureiro, Celso de Oliveira

    2000-01-01

    The main purpose of the present research work is the groundwater flow characterization of the aquifer system of the Engenho Nogueira Creek watershed basin, particularly within the limits of the Pampulha Campus of the Federal University of Minas Gerais and nearby. In order to reach the aforementioned goal, a numerical model was implemented for simulation the groundwater flow, using the MODFLOW code. The local hydrogeology consists of a porous granular aquifer placed above and hydraulically connected to a fractured aquifer, constituting a unique aquifer system, mixed and phreatic type, heterogeneous and anisotropic. The local hydrogeological system is strongly influenced by a complex drain system and by the Engenho Nogueira Creek. After calibration, it was possible to predict the average phreatic depth measured in the observation wells for the period in study with a standard deviation of 1.65 m and a correlation coefficient of 0.94. (author)

  13. Groundwater Data Package for the 2004 Composite Analysis

    Energy Technology Data Exchange (ETDEWEB)

    Thorne, Paul D.

    2004-08-11

    This report presents data and information that supports the groundwater module. The conceptual model of groundwater flow and transport at the Hanford Site is described and specific information applied in the numerical implementation module is provided.

  14. Structural Control and Groundwater Flow in the Nubian Aquifer

    Science.gov (United States)

    Fathy, K.; Sultan, M.; Ahmed, M.; Save, H.; Emil, M. K.; Elkaliouby, B.

    2017-12-01

    An integrated research approach (remote sensing, field, geophysics) was conducted to investigate the structural control on groundwater flow in large aquifers using the less studied Nubian Sandstone Aquifer System (NSAS) of NE Africa as a test site. The aquifer extends over 2.2 x 106 km2 in Egypt, Libya, Chad, and Sudan and consists of thick (> 3 kms), water-bearing, Paleozoic and Mesozoic sandstone with intercalations of Tertiary shale and clay. It is subdivided into three sub-basins (Northern Sudan Platform [NSP], Dakhla [DAS], and Kufra) that are separated by basement uplifts (e.g., E-W trending Uweinat-Aswan uplift that separates DAS from the NSP). Aquifer recharge occurs in the south (NSP and southern Kufra) where the aquifer is unconfined and precipitation is high (Average Annual Precipitation [AAP]: 117 mm/yr.) and discharge is concentrated in the north (DAS and northern Kufra). Our approach is a three-fold exercise. Firstly, we compared GOCE-based Global Geopotential Models (GGMs) to terrestrial gravity anomalies for 21262 sites to select the optimum model for deriving Bouguer gravity anomalies. Secondly, structures and uplifts were mapped using hill shade images and their extension in the subsurface were mapped using the Eigen_6C4 model-derived Bouguer anomalies and their Tilt Derivative products (TDR). Thirdly, hydrological analysis was conducted using GRACE CSR 1° x 1° mascon solutions to investigate the mass variations in relation to the mapped structures. Our findings include: (1) The Eigen-6C4 is the optimum model having the lowest deviation (9.122 mGal) from the terrestrial gravity anomalies; (2) the surface expressions of structures matched fairly well with their postulated extensions in the subsurface; (3) identified fault systems include: Red Sea rift-related N-S to NW-SE trending grabens formed by reactivating basement structures during Red Sea opening and Syrian arc-related NE-SW trending dextral shear systems; (4) TWS patterns are uniform

  15. Geochemical and Isotopic Interpretations of Groundwater Flow in the Oasis Valley Flow System, Southern Nevada

    Energy Technology Data Exchange (ETDEWEB)

    J.M. Thomas; F.C. Benedict, Jr.; T.P. Rose; R.L. Hershey; J.B. Paces; Z.E. Peterman; I.M. Farnham; K.H. Johannesson; A.K. Singh; K.J. Stetzenbach; G.B. Hudson; J.M. Kenneally; G.F. Eaton; D.K. Smith

    2003-01-08

    This report summarizes the findings of a geochemical investigation of the Pahute Mesa-Oasis Valley groundwater flow system in southwestern Nevada. It is intended to provide geochemical data and interpretations in support of flow and contaminant transport modeling for the Western and Central Pahute Mesa Corrective Action Units.

  16. Geochemical and Isotopic Interpretations of Groundwater Flow in the Oasis Valley Flow System, Southern Nevada

    International Nuclear Information System (INIS)

    Thomas, J.M.; Benedict, F.C. Jr.; Rose, T.P.; Hershey, R.L.; Paces, J.B.; Peterman, Z.E.; Farnham, I.M.; Johannesson, K.H.; Singh, A.K.; Stetzenbach, K.J.; Hudson, G.B.; Kenneally, J.M.; Eaton, G.F.; Smith, D.K.

    2003-01-01

    This report summarizes the findings of a geochemical investigation of the Pahute Mesa-Oasis Valley groundwater flow system in southwestern Nevada. It is intended to provide geochemical data and interpretations in support of flow and contaminant transport modeling for the Western and Central Pahute Mesa Corrective Action Units

  17. Separation of base flow from streamflow using groundwater levels - illustrated for the Pang catchment (UK)

    NARCIS (Netherlands)

    Peters, E.; Lanen, van H.A.J.

    2005-01-01

    A new filter to separate base flow from streamflow has developed that uses observed groundwater levels. To relate the base flow to the observed groundwater levels, a non-linear relation was used. This relation is suitable for unconfined aquifers with deep groundwater levels that do not respond to

  18. Closing the irrigation deficit in Cambodia: Implications for transboundary impacts on groundwater and Mekong River flow

    Science.gov (United States)

    Erban, Laura E.; Gorelick, Steven M.

    2016-04-01

    Rice production in Cambodia, essential to food security and exports, is largely limited to the wet season. The vast majority (96%) of land planted with rice during the wet season remains fallow during the dry season. This is in large part due to lack of irrigation capacity, increases in which would entail significant consequences for Cambodia and Vietnam, located downstream on the Mekong River. Here we quantify the extent of the dry season ;deficit; area in the Cambodian Mekong River catchment, using a recent agricultural survey and our analysis of MODIS satellite data. Irrigation of this land for rice production would require a volume of water up to 31% of dry season Mekong River flow to Vietnam. However, the two countries share an aquifer system in the Mekong Delta, where irrigation demand is increasingly met by groundwater. We estimate expansion rates of groundwater-irrigated land to be >10% per year in the Cambodian Delta using LANDSAT satellite data and simulate the effects of future expansion on groundwater levels over a 25-year period. If groundwater irrigation continues to expand at current rates, the water table will drop below the lift limit of suction pump wells, used for domestic supply by >1.5 million people, throughout much of the area within 15 years. Extensive groundwater irrigation jeopardizes access for shallow domestic water supply wells, raises the costs of pumping for all groundwater users, and may exacerbate arsenic contamination and land subsidence that are already widespread hazards in the region.

  19. Regional-to-site scale groundwater flow in Romuvaara

    International Nuclear Information System (INIS)

    Kattilakoski, E.; Koskinen, L.

    1999-04-01

    The work describing numerical groundwater flow modelling at the Romuvaara site serves as a background report for the safety assessment TILA-99. The site scale can roughly be taken as the scale of detailed borehole investigations, which have probed the bedrock of Romuvaara over about 2 km 2 large and 1 km deep volume. The site model in this work covers an area of about 12 km 2 . The depth of the model is 2200 m. The site scale flow modelling produced characteristics of the deep groundwater flow and evaluated the impact of a spent fuel repository on the natural groundwater flow conditions. It treated the hydraulic gradient in the intact rock between the repository and the fracture zone nearest to it (about 50 m off) for the block scale model, which describes the groundwater flow on the repository scale. The result quantities were the hydraulic head h (as the base quantity) and its gradient in selected cross sections and fracture zones, the flow rates around the repository, flow paths and discharge areas of the water from the repository. Two repository layouts were discussed. The numerical simulations were performed with the FEFTRA code based on the porous medium concept and the finite element method. The regional model with a no-flow boundary condition at the bottom and on the lateral edges was firstly used to confirm the hydraulic head boundary condition on the lateral edges of an interior site model (having a no-flow boundary condition at the bottom). The groundwater table was used as the hydraulic head boundary condition at the surface of each model. Both the conductivity of the bedrock (modeled with three-dimensional elements) and the transmissivities of the fracture zones (described with two-dimensional elements in the three-dimensional mesh) decreased as a function of the depth. All the results were derived from the site model. The range of variation of the hydraulic gradient immediately outside the repository was studied in the direction of the flow routes

  20. Regional-to-site scale groundwater flow in Romuvaara

    Energy Technology Data Exchange (ETDEWEB)

    Kattilakoski, E.; Koskinen, L. [VTT Energy, Espoo (Finland)

    1999-04-01

    The work describing numerical groundwater flow modelling at the Romuvaara site serves as a background report for the safety assessment TILA-99. The site scale can roughly be taken as the scale of detailed borehole investigations, which have probed the bedrock of Romuvaara over about 2 km{sup 2} large and 1 km deep volume. The site model in this work covers an area of about 12 km{sup 2}. The depth of the model is 2200 m. The site scale flow modelling produced characteristics of the deep groundwater flow and evaluated the impact of a spent fuel repository on the natural groundwater flow conditions. It treated the hydraulic gradient in the intact rock between the repository and the fracture zone nearest to it (about 50 m off) for the block scale model, which describes the groundwater flow on the repository scale. The result quantities were the hydraulic head h (as the base quantity) and its gradient in selected cross sections and fracture zones, the flow rates around the repository, flow paths and discharge areas of the water from the repository. Two repository layouts were discussed. The numerical simulations were performed with the FEFTRA code based on the porous medium concept and the finite element method. The regional model with a no-flow boundary condition at the bottom and on the lateral edges was firstly used to confirm the hydraulic head boundary condition on the lateral edges of an interior site model (having a no-flow boundary condition at the bottom). The groundwater table was used as the hydraulic head boundary condition at the surface of each model. Both the conductivity of the bedrock (modeled with three-dimensional elements) and the transmissivities of the fracture zones (described with two-dimensional elements in the three-dimensional mesh) decreased as a function of the depth. All the results were derived from the site model. The range of variation of the hydraulic gradient immediately outside the repository was studied in the direction of the flow

  1. Ambient groundwater flow diminishes nitrate processing in the hyporheic zone of streams

    Science.gov (United States)

    Azizian, Morvarid; Boano, Fulvio; Cook, Perran L. M.; Detwiler, Russell L.; Rippy, Megan A.; Grant, Stanley B.

    2017-05-01

    Modeling and experimental studies demonstrate that ambient groundwater reduces hyporheic exchange, but the implications of this observation for stream N-cycling is not yet clear. Here we utilize a simple process-based model (the Pumping and Streamline Segregation or PASS model) to evaluate N-cycling over two scales of hyporheic exchange (fluvial ripples and riffle-pool sequences), ten ambient groundwater and stream flow scenarios (five gaining and losing conditions and two stream discharges), and three biogeochemical settings (identified based on a principal component analysis of previously published measurements in streams throughout the United States). Model-data comparisons indicate that our model provides realistic estimates for direct denitrification of stream nitrate, but overpredicts nitrification and coupled nitrification-denitrification. Riffle-pool sequences are responsible for most of the N-processing, despite the fact that fluvial ripples generate 3-11 times more hyporheic exchange flux. Across all scenarios, hyporheic exchange flux and the Damköhler Number emerge as primary controls on stream N-cycling; the former regulates trafficking of nutrients and oxygen across the sediment-water interface, while the latter quantifies the relative rates of organic carbon mineralization and advective transport in streambed sediments. Vertical groundwater flux modulates both of these master variables in ways that tend to diminish stream N-cycling. Thus, anthropogenic perturbations of ambient groundwater flows (e.g., by urbanization, agricultural activities, groundwater mining, and/or climate change) may compromise some of the key ecosystem services provided by streams.

  2. Radioactive Seepage through Groundwater Flow from the Uranium Mines, Namibia

    Directory of Open Access Journals (Sweden)

    Tamiru Abiye

    2017-02-01

    Full Text Available The study focused on the seepage of uranium from unlined tailing dams into the alluvial aquifer in the Gawib River floodplain in Namibia where the region solely relies on groundwater for its economic activities as a result of arid climatic condition. The study reviewed previous works besides water sample collection and analyses for major ions, metals and environmental isotopes in addition to field tests on physico-chemical parameters (pH, Electrical Conductivity, Redox and T. Estimation of seepage velocity (true velocity of groundwater flow has been conducted in order to understand the extent of radioactive plume transport. The hydrochemistry, stable isotopes and tritium results show that there is uranium contamination from the unlined uranium tailings in the Gawib shallow aquifer system which suggests high permeability of the alluvial aquifer facilitating groundwater flow in the arid region. The radioactive contaminants could spread into the deeper aquifer system through the major structures such as joints and faults. The contamination plume could also spread downstream into the Swakop River unless serious interventions are employed. There is also a very high risk of the plume to reach the Atlantic Ocean through seasonal flash floods that occurs in the area.

  3. Simulation of the regional groundwater-flow system of the Menominee Indian Reservation, Wisconsin

    Science.gov (United States)

    Juckem, Paul F.; Dunning, Charles P.

    2015-01-01

    A regional, two-dimensional, steady-state groundwater-flow model was developed to simulate the groundwater-flow system and groundwater/surface-water interactions within the Menominee Indian Reservation. The model was developed by the U.S. Geological Survey (USGS), in cooperation with the Menominee Indian Tribe of Wisconsin, to contribute to the fundamental understanding of the region’s hydrogeology. The objectives of the regional model were to improve understanding of the groundwater-flow system, including groundwater/surface-water interactions, and to develop a tool suitable for evaluating the effects of potential regional water-management programs. The computer code GFLOW was used because of the ease with which the model can simulate groundwater/surface-water interactions, provide a framework for simulating regional groundwater-flow systems, and be refined in a stepwise fashion to incorporate new data and simulate groundwater-flow patterns at multiple scales. Simulations made with the regional model reproduce groundwater levels and stream base flows representative of recent conditions (1970–2013) and illustrate groundwater-flow patterns with maps of (1) the simulated water table and groundwater-flow directions, (2) probabilistic areas contributing recharge to high-capacity pumped wells, and (3) estimation of the extent of infiltrated wastewater from treatment lagoons.

  4. Groundwater flow modelling of the excavation and operational phases - Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Urban (Computer-aided Fluid Engineering AB, Lyckeby (Sweden)); Rhen, Ingvar (SWECO Environment AB, Falun (Sweden))

    2010-12-15

    As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The modelling study reported here presents calculated inflow rates, drawdown of the groundwater table and upconing of deep saline water for different levels of grouting efficiency during the excavation and operational phases of a final repository at Laxemar. The inflow calculations were accompanied by a sensitivity study, which among other matters handled the impact of different deposition hole rejection criteria. The report also presents tentative modelling results for the duration of the saturation phase, which starts once the used parts of the repository are being backfilled

  5. The 2016 groundwater flow model for Dane County, Wisconsin

    Science.gov (United States)

    Parsen, Michael J.; Bradbury, Kenneth R.; Hunt, Randall J.; Feinstein, Daniel T.

    2016-01-01

    A new groundwater flow model for Dane County, Wisconsin, replaces an earlier model developed in the 1990s by the Wisconsin Geological and Natural History Survey (WGNHS) and the U.S. Geological Survey (USGS). This modeling study was conducted cooperatively by the WGNHS and the USGS with funding from the Capital Area Regional Planning Commission (CARPC). Although the overall conceptual model of the groundwater system remains largely unchanged, the incorporation of newly acquired high-quality datasets, recent research findings, and improved modeling and calibration techniques have led to the development of a more detailed and sophisticated model representation of the groundwater system. The new model is three-dimensional and transient, and conceptualizes the county’s hydrogeology as a 12-layer system including all major unlithified and bedrock hydrostratigraphic units and two high-conductivity horizontal fracture zones. Beginning from the surface down, the model represents the unlithified deposits as two distinct model layers (1 and 2). A single layer (3) simulates the Ordovician sandstone and dolomite of the Sinnipee, Ancell, and Prairie du Chien Groups. Sandstone of the Jordan Formation (layer 4) and silty dolostone of the St. Lawrence Formation (layer 5) each comprise separate model layers. The underlying glauconitic sandstone of the Tunnel City Group makes up three distinct layers: an upper aquifer (layer 6), a fracture feature (layer 7), and a lower aquifer (layer 8). The fracture layer represents a network of horizontal bedding-plane fractures that serve as a preferential pathway for groundwater flow. The model simulates the sandstone of the Wonewoc Formation as an upper aquifer (layer 9) with a bedding-plane fracture feature (layer 10) at its base. The Eau Claire aquitard (layer 11) includes shale beds within the upper portion of the Eau Claire Formation. This layer, along with overlying bedrock units, is mostly absent in the preglacially eroded valleys along

  6. Investigating riparian groundwater flow close to a losing river using diurnal temperature oscillations at high vertical resolution

    Directory of Open Access Journals (Sweden)

    T. Vogt

    2012-02-01

    Full Text Available River-water infiltration is of high relevance for hyporheic and riparian groundwater ecology as well as for drinking water supply by river-bank filtration. Heat has become a popular natural tracer to estimate exchange rates between rivers and groundwater. However, quantifying flow patterns and velocities is impeded by spatial and temporal variations of exchange fluxes, insufficient sensors spacing during field investigations, or simplifying assumptions for analysis or modeling such as uniform flow. The objective of this study is to investigate lateral shallow groundwater flow upon river-water infiltration at the shoreline of the riverbed and in the adjacent riparian zone of the River Thur in northeast Switzerland. Here we have applied distributed temperature sensing (DTS along optical fibers wrapped around tubes to measure high-resolution vertical temperature profiles of the unsaturated zone and shallow riparian groundwater. Diurnal temperature oscillations were tracked in the subsurface and analyzed by means of dynamic harmonic regression to extract amplitudes and phase angles. Subsequent calculations of amplitude attenuation and time shift relative to the river signal show in detail vertical and temporal variations of heat transport in shallow riparian groundwater. In addition, we apply a numerical two-dimensional heat transport model for the unsaturated zone and shallow groundwater to obtain a better understanding of the observed heat transport processes in shallow riparian groundwater and to estimate the groundwater flow velocity. Our results show that the observed riparian groundwater temperature distribution cannot be described by uniform flow, but rather by horizontal groundwater flow velocities varying over depth. In addition, heat transfer of diurnal temperature oscillations from the losing river through shallow groundwater is influenced by thermal exchange with the unsaturated zone. Neglecting the influence of the unsaturated zone

  7. Recent Developments in Karst Groundwater Flow Measurement in Southeastern Florida,USA

    Science.gov (United States)

    Krupa, S.; Brock, J.; Gefvert, C.; Shaffer, J.; Cunningham, K.; Wacker, M.

    2008-05-01

    Groundwater seepage was first characterized in the early 1800's, when Henry Darcy determined that the flow of groundwater could be estimated from the head difference and the distance between two points. Since then, hydrogeologists have been struggling with ways to continuously measure groundwater flow in situ, and more recently have sought data in near-real time. Groundwater flow within aquifers that have relatively large head differences (several meters) are porous in nature and have low hydraulic conductivities, is linear in nature, and can be generally characterized by Darcy's solution. Prior to the research presented herein, it was assumed that aquifers within Miami-Dade County could also be characterized by Darcy's solution (with Reynolds numbers less than 10 or 20). The L-31N Canal lies on the eastern flank of Everglades National Park (ENP). In addition to conveying water to Florida Bay and Biscayne Bay, the canal's levees are intended to reduce surface-water sheet flow from ENP to eastern urban areas. In an effort to reduce groundwater seepage coming from ENP, the South Florida Water Management District (SFWMD) and the United States Army Corp of Engineers (USACE) have been tasked with evaluating the hydrogeology and the groundwater/surface-water interaction on the L-31N canal. This involved process of installation includes monitoring wells, recording automated water-level measurements, characterizing water-chemistry types and ages, and installation of instruments capable of measuring horizontal groundwater velocities and directions coming from ENP. The SFWMD initiated a cooperative agreement with the United States Geological Survey (USGS) for the geological and hydrogeological investigation and concurrently contracted the installation of borehole flowmeters in eight wells (two clusters). The USGS provided detailed core and sediment analysis, geophysical logging, in situ borehole flowmeter logging, and digital optical borehole imaging. In addition, the USGS

  8. Numerical Modeling of Regional Groundwater Flow in a Structurally Complex Intermountain Basin: South Park, Colorado

    Science.gov (United States)

    Ball, L. B.; Caine, J. S.; Ge, S.

    2012-12-01

    A steady-state, 3-D groundwater flow model of the South Park basin was developed to explore the influence of realistically complex topography and permeability structure on the patterns of basin-wide groundwater flow and to evaluate the sensitivity of the groundwater flow system to increased variability in recharge distribution and the influence of hydrogeologically distinct fault zones. South Park is a large, semi-arid intermountain basin (3300 km2) flanked by crystalline rocks and floored with faulted and folded sedimentary rocks and volcanic deposits. Model results suggest that, while the majority (>80%) of water entering the groundwater flow system is discharged through seepage faces in steep terrain or routed to mountain streams, internal exchanges of groundwater and stream flow between the mountain and valley landscapes are an important part of the dynamics of groundwater flow in the basin. The majority of topographically driven groundwater flow is focused in the upper 300 m of the model domain and would be considered local to intermediate in "Tothian" scales. Less than 1% of groundwater flow passes below 1 km in depth, and large-scale regional circulation is a limited component of the groundwater flow system. Increasingly heterogeneous recharge distributions most heavily impacted the groundwater flow system at the local scale, while basin-wide regional flow remained relatively insensitive to the increasing variability in recharge distribution. The introduction of end-member conduit and barrier types of fault zones influenced hydraulic heads and gradients within 5-10 km of the fault location where groundwater flow directions are perpendicular to the orientation of the fault. Where groundwater flow directions are oblique or subparallel to the fault, the introduction of distinct fault zones had a negligible impact on hydraulic heads or gradients.

  9. Composite use of numerical groundwater flow modeling and geoinformatics techniques for monitoring Indus Basin aquifer, Pakistan.

    Science.gov (United States)

    Ahmad, Zulfiqar; Ashraf, Arshad; Fryar, Alan; Akhter, Gulraiz

    2011-02-01

    The integration of the Geographic Information System (GIS) with groundwater modeling and satellite remote sensing capabilities has provided an efficient way of analyzing and monitoring groundwater behavior and its associated land conditions. A 3-dimensional finite element model (Feflow) has been used for regional groundwater flow modeling of Upper Chaj Doab in Indus Basin, Pakistan. The approach of using GIS techniques that partially fulfill the data requirements and define the parameters of existing hydrologic models was adopted. The numerical groundwater flow model is developed to configure the groundwater equipotential surface, hydraulic head gradient, and estimation of the groundwater budget of the aquifer. GIS is used for spatial database development, integration with a remote sensing, and numerical groundwater flow modeling capabilities. The thematic layers of soils, land use, hydrology, infrastructure, and climate were developed using GIS. The Arcview GIS software is used as additive tool to develop supportive data for numerical groundwater flow modeling and integration and presentation of image processing and modeling results. The groundwater flow model was calibrated to simulate future changes in piezometric heads from the period 2006 to 2020. Different scenarios were developed to study the impact of extreme climatic conditions (drought/flood) and variable groundwater abstraction on the regional groundwater system. The model results indicated a significant response in watertable due to external influential factors. The developed model provides an effective tool for evaluating better management options for monitoring future groundwater development in the study area.

  10. Sensitivity studies of unsaturated groundwater flow modeling for groundwater travel time calculations at Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Altman, S.J.; Ho, C.K.; Arnold, B.W.; McKenna, S.A.

    1995-01-01

    Unsaturated flow has been modeled through four cross-sections at Yucca Mountain, Nevada, for the purpose of determining groundwater particle travel times from the potential repository to the water table. This work will be combined with the results of flow modeling in the saturated zone for the purpose of evaluating the suitability of the potential repository under the criteria of 10CFR960. One criterion states, in part, that the groundwater travel time (GWTT) from the repository to the accessible environment must exceed 1,000 years along the fastest path of likely and significant radionuclide travel. Sensitivity analyses have been conducted for one geostatistical realization of one cross-section for the purpose of (1) evaluating the importance of hydrological parameters having some uncertainty and (2) examining conceptual models of flow by altering the numerical implementation of the conceptual model (dual permeability (DK) and the equivalent continuum model (ECM). Results of comparisons of the ECM and DK model are also presented in Ho et al

  11. Analysis of ground-water flow in the Madison aquifer using fluorescent dyes injected in Spring Creek and Rapid Creek near Rapid City, South Dakota, 2003-04

    Science.gov (United States)

    Putnam, Larry D.; Long, Andrew J.

    2007-01-01

    , which is located adjacent to the loss zone, was similar to the concentration in the stream. Fluorescein arrived at well NON (injection at site S1), which is located about 2 miles northeast of the loss zone, within about 1.6 days, and the maximum concentration was 44 ug/L. For injection at site S4, when streamflow was about 12 ft3/s, fluorescein was detected in samples from six wells and time to first arrival ranged from 0.2 to 16 days. Following injection at site S4 in 2004, the length of time that dye remained in the capture zone of well NON, which is located approximately 2 miles from the loss zone, was almost an order of magnitude greater than in 2003. For injection at site R1, Rhodamine WT was detected at well DRU and spring TI-SP with time to first arrival of about 0.5 and 1.1 days and maximum concentrations of 6.2 and 0.91 ug/L, respectively. Well DRU and spring TI-SP are located near the center of the Rapid Creek loss zone where the creek has a large meander. Measurable concentrations were observed for spring TI-SP as many as 109 days after the dye injection. The direction of a conduit flow path in the Spring Creek area was to the northeast with ground-water velocities that ranged from 770 to 6,500 feet per day. In the Rapid Creek loss zone, a conduit flow path east of the loss zone was not evident from the dye injection.

  12. Coastal groundwater discharge for the U.S. East and Gulf Coasts calculated with three-dimensional groundwater flow models

    Science.gov (United States)

    Befus, K. M.; Kroeger, K. D.; Smith, C. G.; Swarzenski, P. W.

    2017-12-01

    Fresh groundwater discharge to coastal environments contribute to the physical and chemical conditions of coastal waters. At regional scales, groundwater fluxes remain poorly constrained, representing uncertainty in both water and chemical budgets that have implications for downstream ecosystem health and for how human activities alter coastal hydrologic processes. Coastal groundwater discharges remain widely unconstrained due to the interconnectedness of highly heterogeneous hydrogeologic frameworks and hydrologic conditions. We use regional-scale, three-dimensional groundwater flow models with the best available hydrostratigraphic framework data to calculate the magnitude of groundwater discharging from coastal aquifers to coastal waterbodies along the eastern U.S. In addition, we constrain the inland areas that contribute to coastal groundwater discharges using particle tracking. We find that 27 km3/yr of groundwater enters coastal waters of the eastern U.S. and Gulf of Mexico and was over 175,000 km2. The contributing areas to coastal groundwater discharge extended kilometers inland and often were supplied by recharge occurring tens of kilometers inland. These results suggest that coastal groundwater discharges rely on larger contributing areas and potentially transport more dissolved constituents than previously calculated, which are important factors for constraining the role of groundwater in coastal chemical budgets and its impacts on coastal ecosystems.

  13. Interpreting Repeated Temperature-Depth Profiles for Groundwater Flow

    Science.gov (United States)

    Bense, Victor F.; Kurylyk, Barret L.; van Daal, Jonathan; van der Ploeg, Martine J.; Carey, Sean K.

    2017-10-01

    Temperature can be used to trace groundwater flows due to thermal disturbances of subsurface advection. Prior hydrogeological studies that have used temperature-depth profiles to estimate vertical groundwater fluxes have either ignored the influence of climate change by employing steady-state analytical solutions or applied transient techniques to study temperature-depth profiles recorded at only a single point in time. Transient analyses of a single profile are predicated on the accurate determination of an unknown profile at some time in the past to form the initial condition. In this study, we use both analytical solutions and a numerical model to demonstrate that boreholes with temperature-depth profiles recorded at multiple times can be analyzed to either overcome the uncertainty associated with estimating unknown initial conditions or to form an additional check for the profile fitting. We further illustrate that the common approach of assuming a linear initial temperature-depth profile can result in significant errors for groundwater flux estimates. Profiles obtained from a borehole in the Veluwe area, Netherlands in both 1978 and 2016 are analyzed for an illustrative example. Since many temperature-depth profiles were collected in the late 1970s and 1980s, these previously profiled boreholes represent a significant and underexploited opportunity to obtain repeat measurements that can be used for similar analyses at other sites around the world.

  14. Regional-to-site scale groundwater flow in Kivetty

    International Nuclear Information System (INIS)

    Kattilakoski, E.; Meszaros, F.

    1999-04-01

    The work describing numerical groundwater flow modelling at the Kivetty site serves as a background report for the safety assessment TILA-99. The site scale can roughly be taken as the scale of detailed borehole investigations, which have probed the bedrock of Kivetty over about 3 km 2 large and 1 km deep volume. The site model in this work covers an area of about 16 km 2 . The depth of the model is 2000 m. The site scale flow modelling produced characteristics of the deep groundwater flow both under the natural conditions and in the case of a spent fuel repository. The hydraulic gradient in the intact rock between the repository and the fracture zone nearest to it (about 50 m off) was assessed for the block scale model. The result quantities were the hydraulic head h (as the base quantity) and its gradient in selected cross sections and fracture zones, the flow rates around the repository, flow paths and discharge areas of the water from the repository. Two repository layouts were discussed. The numerical simulations were performed with the FEFTRA code based on the porous medium concept and the finite element method. The regional model with a no-flow boundary condition at the bottom and on the lateral edges was firstly used to confirm the hydraulic head boundary condition on the lateral edges of an interior site model (having a no-flow boundary condition at the bottom). The groundwater table was used as the hydraulic head boundary condition at the surface of each model. Both the conductivity of the bedrock (modeled with three-dimensional elements) and the transmissivities of the fracture zones (described with two-dimensional elements in the three-dimensional mesh) decreased as a function of the depth. All the results were derived from the site model. With the exception of the western part of Repository A the outlined repositories are located underneath Kumpuvuori, where the flow has a significant subvertical component. The horizontal component of the deep

  15. Regional-to-site scale groundwater flow in Kivetty

    Energy Technology Data Exchange (ETDEWEB)

    Kattilakoski, E. [VTT Energy, Espoo (Finland); Meszaros, F. [The Relief Laboratory, Harskut (Hungary)

    1999-04-01

    The work describing numerical groundwater flow modelling at the Kivetty site serves as a background report for the safety assessment TILA-99. The site scale can roughly be taken as the scale of detailed borehole investigations, which have probed the bedrock of Kivetty over about 3 km{sup 2} large and 1 km deep volume. The site model in this work covers an area of about 16 km{sup 2}. The depth of the model is 2000 m. The site scale flow modelling produced characteristics of the deep groundwater flow both under the natural conditions and in the case of a spent fuel repository. The hydraulic gradient in the intact rock between the repository and the fracture zone nearest to it (about 50 m off) was assessed for the block scale model. The result quantities were the hydraulic head h (as the base quantity) and its gradient in selected cross sections and fracture zones, the flow rates around the repository, flow paths and discharge areas of the water from the repository. Two repository layouts were discussed. The numerical simulations were performed with the FEFTRA code based on the porous medium concept and the finite element method. The regional model with a no-flow boundary condition at the bottom and on the lateral edges was firstly used to confirm the hydraulic head boundary condition on the lateral edges of an interior site model (having a no-flow boundary condition at the bottom). The groundwater table was used as the hydraulic head boundary condition at the surface of each model. Both the conductivity of the bedrock (modeled with three-dimensional elements) and the transmissivities of the fracture zones (described with two-dimensional elements in the three-dimensional mesh) decreased as a function of the depth. All the results were derived from the site model. With the exception of the western part of Repository A the outlined repositories are located underneath Kumpuvuori, where the flow has a significant subvertical component. The horizontal component of the deep

  16. Updated comparison of groundwater flow model results and isotopic data in the Leon Valley, Mexico

    Science.gov (United States)

    Hernandez-Garcia, G. D.

    2015-12-01

    Northwest of Mexico City, the study area is located in the State of Guanajuato. Leon Valley has covered with groundwater its demand of water, estimated in 20.6 cubic meters per second. The constant increase of population and economic activities in the region, mainly in cities and automobile factories, has also a constant growth in water needs. Related extraction rate has produced an average decrease of approximately 1.0 m per year over the past two decades. This suggests that the present management of the groundwater should be checked. Management of groundwater in the study area involves the possibility of producing environmental impacts by extraction. This vital resource under stress becomes necessary studying its hydrogeological functioning to achieve scientific management of groundwater in the Valley. This research was based on the analysis and integration of existing information and the field generated by the authors. On the base of updated concepts like the geological structure of the area, the hydraulic parameters and the composition of deuterium-delta and delta-oxygen -18, this research has new results. This information has been fully analyzed by applying a groundwater flow model with particle tracking: the result has also a similar result in terms of travel time and paths derived from isotopic data.

  17. Groundwater flow and transport modelling during a glaciation period

    International Nuclear Information System (INIS)

    Jaquet, O.; Siegel, P.

    2003-01-01

    Subsequent to earlier work, SKB has decided to carry out additional hydrogeological modelling studies related to glaciation effects at Aespoe. In particular, sub glacial groundwater flow and the impact assessment on a repository require further studies. As compared to the previous model, the domain geometry and processes involved remain identical, but this time, numerical calculations are performed with the NAMMU package (version 7.1.1) using a finite element formulation. Modified assumptions corresponding to specific boundary conditions are implemented and additional variations of the base case are simulated. The objectives of the study are based on the technical specifications established by SKB. The main objectives may be summarised as follows: Enhancement of the understanding of sub glacial groundwater flow due to basal ice melting. Evaluation of the impact of sub glacial roundwater flow on a repository with respect to its position to the ice margin of the glacier. Assessment of the feasibility of performing large 3D simulations of density-driven flow induced by variable salinity of the groundwater using the NAMMU package. The report begins with an account of the modelling approach applied. Then, the results of the different cases simulated are described, analysed and interpreted in detail. Finally, conclusions are drawn up together with some recommendations related to potential modelling issues for the future. The objectives proposed for the groundwater flow and transport modelling for period of glaciation have been met: The results have shown the importance of the ice tunnels in governing sub glacial groundwater flow due to basal ice melting. The influence of the ice tunnels on the salinity distribution is significant as is their impact on the flow trajectories and, hence, on the resulting travel times. The results of simulation S0 have revealed that no steady-state flow conditions are reached. Due to the chosen salt boundary conditions, salt will continue to

  18. Simple evaluation of groundwater flow and radionuclide transport at Aespoe

    International Nuclear Information System (INIS)

    Dverstorp, B.; Geier, J.; Voss, C.

    1996-12-01

    A simple evaluation of groundwater flux and potential for radionuclide transport at the Aespoe site, from fundamental hydrologic principles, indicates that, based upon data that are available from surface-based investigations, it is not possible to confirm that the bedrock has a high capacity to retard radionuclide release to the surface environment. This result is primarily due to the high spatial variability of hydraulic conductivity, and high uncertainty regarding the relationship among hydrologic and transport parameters within conductive elements of the bedrock. A comparison between Aespoe and seven other study sites in Sweden indicates that it is difficult or impossible to discriminate among these sites in terms of the geologic barrier function, based upon the types of data that are available from present-day methods of site characterization. Groundwater flux is evaluated by a one-dimensional application of Darcy's law to a set of simple, potential pathways for groundwater flow from the repository, which are chosen to yield an appraisal of the wide bounds of possible system behaviour. The configurations of the pathways are specified based on simple assumptions of flow-field structure, and hydraulic driving forces are specified from consideration of regional and local topographic differences. Results are expressed in terms of a parameter group that has been shown to control the barrier function. Comparisons with more detailed hydrological modelling of Aespoe show that, although a reduction in uncertainty is achieved, this reduction is not sufficient to distinguish between good and poor performance of the geologic barrier at the site. 38 refs

  19. Simple evaluation of groundwater flow and radionuclide transport at Aespoe

    Energy Technology Data Exchange (ETDEWEB)

    Dverstorp, B. [Swedish Nuclear Power Inspectorate, Stockholm (Sweden); Geier, J. [Clearwater Hardrock Consulting, Monmouth, OR, (United States); Voss, C. [Geological Survey, Reston, VA (United States)

    1996-12-01

    A simple evaluation of groundwater flux and potential for radionuclide transport at the Aespoe site, from fundamental hydrologic principles, indicates that, based upon data that are available from surface-based investigations, it is not possible to confirm that the bedrock has a high capacity to retard radionuclide release to the surface environment. This result is primarily due to the high spatial variability of hydraulic conductivity, and high uncertainty regarding the relationship among hydrologic and transport parameters within conductive elements of the bedrock. A comparison between Aespoe and seven other study sites in Sweden indicates that it is difficult or impossible to discriminate among these sites in terms of the geologic barrier function, based upon the types of data that are available from present-day methods of site characterization. Groundwater flux is evaluated by a one-dimensional application of Darcy`s law to a set of simple, potential pathways for groundwater flow from the repository, which are chosen to yield an appraisal of the wide bounds of possible system behaviour. The configurations of the pathways are specified based on simple assumptions of flow-field structure, and hydraulic driving forces are specified from consideration of regional and local topographic differences. Results are expressed in terms of a parameter group that has been shown to control the barrier function. Comparisons with more detailed hydrological modelling of Aespoe show that, although a reduction in uncertainty is achieved, this reduction is not sufficient to distinguish between good and poor performance of the geologic barrier at the site. 38 refs.

  20. SR-Site groundwater flow modelling methodology, setup and results

    Energy Technology Data Exchange (ETDEWEB)

    Selroos, Jan-Olof (Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden)); Follin, Sven (SF GeoLogic AB, Taeby (Sweden))

    2010-12-15

    As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken three groundwater flow modelling studies. These are performed within the SR-Site project and represent time periods with different climate conditions. The simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. Three time periods are addressed; the Excavation and operational phases, the Initial period of temperate climate after closure, and the Remaining part of the reference glacial cycle. The present report is a synthesis of the background reports describing the modelling methodology, setup, and results. It is the primary reference for the conclusions drawn in a SR-Site specific context concerning groundwater flow during the three climate periods. These conclusions are not necessarily provided explicitly in the background reports, but are based on the results provided in these reports. The main results and comparisons presented in the present report are summarised in the SR-Site Main report.

  1. A surrogate-based sensitivity quantification and Bayesian inversion of a regional groundwater flow model

    Science.gov (United States)

    Chen, Mingjie; Izady, Azizallah; Abdalla, Osman A.; Amerjeed, Mansoor

    2018-02-01

    Bayesian inference using Markov Chain Monte Carlo (MCMC) provides an explicit framework for stochastic calibration of hydrogeologic models accounting for uncertainties; however, the MCMC sampling entails a large number of model calls, and could easily become computationally unwieldy if the high-fidelity hydrogeologic model simulation is time consuming. This study proposes a surrogate-based Bayesian framework to address this notorious issue, and illustrates the methodology by inverse modeling a regional MODFLOW model. The high-fidelity groundwater model is approximated by a fast statistical model using Bagging Multivariate Adaptive Regression Spline (BMARS) algorithm, and hence the MCMC sampling can be efficiently performed. In this study, the MODFLOW model is developed to simulate the groundwater flow in an arid region of Oman consisting of mountain-coast aquifers, and used to run representative simulations to generate training dataset for BMARS model construction. A BMARS-based Sobol' method is also employed to efficiently calculate input parameter sensitivities, which are used to evaluate and rank their importance for the groundwater flow model system. According to sensitivity analysis, insensitive parameters are screened out of Bayesian inversion of the MODFLOW model, further saving computing efforts. The posterior probability distribution of input parameters is efficiently inferred from the prescribed prior distribution using observed head data, demonstrating that the presented BMARS-based Bayesian framework is an efficient tool to reduce parameter uncertainties of a groundwater system.

  2. Effect of volcanic dykes on coastal groundwater flow and saltwater intrusion: A field-scale multiphysics approach and parameter evaluation

    Science.gov (United States)

    Comte, J.-C.; Wilson, C.; Ofterdinger, U.; González-Quirós, A.

    2017-03-01

    Volcanic dykes are common discrete heterogeneities in aquifers; however, there is a lack of field examples of, and methodologies for, comprehensive in situ characterization of their properties with respect to groundwater flow and solute transport. We have applied an integrated multiphysics approach to quantify the effect of dolerite dykes on saltwater intrusion in a coastal sandstone aquifer. The approach involved ground geophysical imaging (passive magnetics and electrical resistivity tomography), well hydraulic testing, and tidal propagation analysis, which provided constraints on the geometry of the dyke network, the subsurface saltwater distribution, and the sandstone hydrodynamic properties and connectivity. A three-dimensional variable-density groundwater model coupled with a resistivity model was further calibrated using groundwater and geophysical observations. A good agreement of model simulations with tide-induced head fluctuations, geophysically derived pore water salinities, and measured apparent resistivities was obtained when dykes' hydraulic conductivity, storativity, and effective porosity are respectively about 3, 1, and 1 orders of magnitude lower than the host aquifer. The presence of the dykes results in barrier-like alterations of groundwater flow and saltwater intrusion. Preferential flow paths occur parallel to observed dyke orientations. Freshwater inflows from upland recharge areas concentrate on the land-facing side of the dykes and saltwater penetration is higher on their sea-facing side. This has major implications for managing groundwater resources in dyke-intruded aquifers, including in coastal and island regions and provides wider insights on preferential pathways of groundwater flow and transport in highly heterogeneous aquifer systems.

  3. Evaluation of Uncertainties in hydrogeological modeling and groundwater flow analyses. Model calibration

    International Nuclear Information System (INIS)

    Ijiri, Yuji; Ono, Makoto; Sugihara, Yutaka; Shimo, Michito; Yamamoto, Hajime; Fumimura, Kenichi

    2003-03-01

    This study involves evaluation of uncertainty in hydrogeological modeling and groundwater flow analysis. Three-dimensional groundwater flow in Shobasama site in Tono was analyzed using two continuum models and one discontinuous model. The domain of this study covered area of four kilometers in east-west direction and six kilometers in north-south direction. Moreover, for the purpose of evaluating how uncertainties included in modeling of hydrogeological structure and results of groundwater simulation decreased with progress of investigation research, updating and calibration of the models about several modeling techniques of hydrogeological structure and groundwater flow analysis techniques were carried out, based on the information and knowledge which were newly acquired. The acquired knowledge is as follows. As a result of setting parameters and structures in renewal of the models following to the circumstances by last year, there is no big difference to handling between modeling methods. The model calibration is performed by the method of matching numerical simulation with observation, about the pressure response caused by opening and closing of a packer in MIU-2 borehole. Each analysis technique attains reducing of residual sum of squares of observations and results of numerical simulation by adjusting hydrogeological parameters. However, each model adjusts different parameters as water conductivity, effective porosity, specific storage, and anisotropy. When calibrating models, sometimes it is impossible to explain the phenomena only by adjusting parameters. In such case, another investigation may be required to clarify details of hydrogeological structure more. As a result of comparing research from beginning to this year, the following conclusions are obtained about investigation. (1) The transient hydraulic data are effective means in reducing the uncertainty of hydrogeological structure. (2) Effective porosity for calculating pore water velocity of

  4. Estimation of groundwater flow rate using the decay of 222Rn in a well

    International Nuclear Information System (INIS)

    Hamada, Hiromasa

    1999-01-01

    A method of estimating groundwater flow rate using the decay of 222 Rn in a well was investigated. Field application revealed that infiltrated water (i.e., precipitation, pond water and irrigation water) accelerated groundwater flow. In addition, the depth at which groundwater was influenced by surface water was determined. The velocity of groundwater in a test well was estimated to be of the order of 10 -6 cm s -1 , based on the ratio of 222 Rn concentration in groundwater before and after it flowed into the well. This method is applicable for monitoring of groundwater flow rate where the velocity in a well is from 10 -5 to 10 -6 cm s -1

  5. Representation of an open repository in groundwater flow models

    International Nuclear Information System (INIS)

    Painter, Scott; Sun, Alexander

    2005-08-01

    The effect of repository tunnels on groundwater flow has been identified as a potential issue for the nuclear waste repository being considered by SKB for a fractured granite formation in Sweden. In particular, the following pre-closure and post-closure processes have been identified as being important: inflows into open tunnels as functions of estimated grouting efficiencies, drawdown of the water table in the vicinity of the repository, upcoming of saline water, 'turnover' of surface water in the upper bedrock, and resaturation of backfilled tunnels following repository closure. The representation of repository tunnels within groundwater models is addressed in this report. The primary focus is on far-field flow that is modeled with a continuum porous medium approximation. Of particular interest are the consequences of the tunnel representation on the transient response of the groundwater system to repository operations and repository closure, as well as modeling issues such as how the water-table free surface and the coupling to near-surface hydrogeology should be handled. The overall objectives are to understand the consequences of current representations and to identify appropriate approximations for representing open tunnels in future groundwater modeling studies. The following conclusions can be drawn from the results of the simulations: 1. Two-phase flow may be induced in the vicinity of repository tunnels during repository pre-closure operations, but the formation of a two-phase flow region will not significantly affect far-field flow or inflows into tunnels. 2. The water table will be drawn down to the repository horizon and tunnel inflows will reach a steady-state value within about 5 years. 3. Steady-state inflows at the repository edge are estimated to be about 250 m 3 /year per meter of tunnel. Inflows will be greater during the transient de-watering period and less for tunnel locations closer to the repository center. 4. Significant amounts of water

  6. Representation of an open repository in groundwater flow models

    Energy Technology Data Exchange (ETDEWEB)

    Painter, Scott; Sun, Alexander [Southwest Research Inst., San Antonio, TX (United States). Center for Nuclear Waste Regulatory Analyses

    2005-08-01

    The effect of repository tunnels on groundwater flow has been identified as a potential issue for the nuclear waste repository being considered by SKB for a fractured granite formation in Sweden. In particular, the following pre-closure and post-closure processes have been identified as being important: inflows into open tunnels as functions of estimated grouting efficiencies, drawdown of the water table in the vicinity of the repository, upcoming of saline water, 'turnover' of surface water in the upper bedrock, and resaturation of backfilled tunnels following repository closure. The representation of repository tunnels within groundwater models is addressed in this report. The primary focus is on far-field flow that is modeled with a continuum porous medium approximation. Of particular interest are the consequences of the tunnel representation on the transient response of the groundwater system to repository operations and repository closure, as well as modeling issues such as how the water-table free surface and the coupling to near-surface hydrogeology should be handled. The overall objectives are to understand the consequences of current representations and to identify appropriate approximations for representing open tunnels in future groundwater modeling studies. The following conclusions can be drawn from the results of the simulations: 1. Two-phase flow may be induced in the vicinity of repository tunnels during repository pre-closure operations, but the formation of a two-phase flow region will not significantly affect far-field flow or inflows into tunnels. 2. The water table will be drawn down to the repository horizon and tunnel inflows will reach a steady-state value within about 5 years. 3. Steady-state inflows at the repository edge are estimated to be about 250 m{sup 3}/year per meter of tunnel. Inflows will be greater during the transient de-watering period and less for tunnel locations closer to the repository center. 4. Significant

  7. Groundwater flow modelling of an abandoned partially open repository

    International Nuclear Information System (INIS)

    Bockgaard, Niclas

    2010-12-01

    As a part of the license application, according to the nuclear activities act, for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The modelling study presented here serves as an input for analyses of so-called future human actions that may affect the repository. The objective of the work was to investigate the hydraulic influence of an abandoned partially open repository. The intention was to illustrate a pessimistic scenario of the effect of open tunnels in comparison to the reference closure of the repository. The effects of open tunnels were studied for two situations with different boundary conditions: A 'temperate' case with present-day boundary conditions and a generic future 'glacial' case with an ice sheet covering the repository. The results were summarized in the form of analyses of flow in and out from open tunnels, the effect on hydraulic head and flow in the surrounding rock volume, and transport performance measures of flow paths from the repository to surface

  8. First status report on regional and local ground-water flow modeling for Richton Dome, Mississippi

    International Nuclear Information System (INIS)

    Andrews, R.W.; Metcalfe, D.E.

    1984-03-01

    Regional and local ground-water flow within the principal hydrogeologic units in the vicinity of Richton Dome is evaluated by developing conceptual models of the flow regime within these units at three different scales and testing these models using a three-dimensional, finite-difference flow code. Semiquantitative sensitivity analysis is conducted to define the system response to changes in the conceptual model, particularly the hydrologic properties. The effects of salinity on the flow field are evaluated at the refined and local scales. Adjoint sensitivity analysis is applied to the conceptualized flow regime in the Wilcox aquifer. All steps leading to the final results and conclusions are incorporated in this report. The available data utilized in this study is summarized. The specific conceptual models, defining the areal and vertical averaging of lithologic units, aquifer properties, fluid properties, and hydrologic boundary conditions, are described in detail. The results are delineated by the simulated potentiometric surfaces and tables summarizing areal and vertical boundary fluxes, Darcy velocities at specific points, and ground-water travel paths. These results are presented at regional, refined, and local (near-dome) scales. The reported work is the first stage of an ongoing evaluation of the Richton Dome as a potential repository for high-level radioactive wastes. The results and conclusions should thus be considered preliminary and subject to modification with the collection of additional data. However, this report does provide a useful basis for describing the sensitivity and, to a lesser extent, the uncertainty of the present conceptualization of ground-water flow in the vicinity of Richton Dome. 25 references, 69 figures, 15 tables

  9. Scaling of flow and transport behavior in heterogeneous groundwater systems

    Science.gov (United States)

    Scheibe, Timothy; Yabusaki, Steven

    1998-11-01

    Three-dimensional numerical simulations using a detailed synthetic hydraulic conductivity field developed from geological considerations provide insight into the scaling of subsurface flow and transport processes. Flow and advective transport in the highly resolved heterogeneous field were modeled using massively parallel computers, providing a realistic baseline for evaluation of the impacts of parameter scaling. Upscaling of hydraulic conductivity was performed at a variety of scales using a flexible power law averaging technique. A series of tests were performed to determine the effects of varying the scaling exponent on a number of metrics of flow and transport behavior. Flow and transport simulation on high-performance computers and three-dimensional scientific visualization combine to form a powerful tool for gaining insight into the behavior of complex heterogeneous systems. Many quantitative groundwater models utilize upscaled hydraulic conductivity parameters, either implicitly or explicitly. These parameters are designed to reproduce the bulk flow characteristics at the grid or field scale while not requiring detailed quantification of local-scale conductivity variations. An example from applied groundwater modeling is the common practice of calibrating grid-scale model hydraulic conductivity or transmissivity parameters so as to approximate observed hydraulic head and boundary flux values. Such parameterizations, perhaps with a bulk dispersivity imposed, are then sometimes used to predict transport of reactive or non-reactive solutes. However, this work demonstrates that those parameters that lead to the best upscaling for hydraulic conductivity and head do not necessarily correspond to the best upscaling for prediction of a variety of transport behaviors. This result reflects the fact that transport is strongly impacted by the existence and connectedness of extreme-valued hydraulic conductivities, in contrast to bulk flow which depends more strongly on

  10. Simulation of groundwater flow and effects of groundwater irrigation on stream base flow in the Elkhorn and Loup River Basins, Nebraska, 1895-2055-Phase Two

    Science.gov (United States)

    Stanton, Jennifer S.; Peterson, Steven M.; Fienen, Michael N.

    2010-01-01

    Regional groundwater-flow simulations for a 30,000-square-mile area of the High Plains aquifer, referred to collectively as the Elkhorn-Loup Model, were developed to predict the effects of groundwater irrigation on stream base flow in the Elkhorn and Loup River Basins, Nebraska. Simulations described the stream-aquifer system from predevelopment through 2005 [including predevelopment (pre-1895), early development (1895-1940), and historical development (1940 through 2005) conditions] and future hypothetical development conditions (2006 through 2033 or 2055). Predicted changes to stream base flow that resulted from simulated changes to groundwater irrigation will aid development of long-term strategies for management of hydrologically connected water supplies. The predevelopment through 2005 simulation was calibrated using an automated parameter-estimation method to optimize the fit to pre-1940 groundwater levels and base flows, 1945 through 2005 decadal groundwater-level changes, and 1940 through 2005 base flows. The calibration results of the pre-1940 period indicated that 81 percent of the simulated groundwater levels were within 30 feet of the measured water levels. The results did not indicate large areas of simulated groundwater levels that were biased too high or too low, indicating that the simulation generally captures the regional trends. Calibration results using 1945 through 2005 decadal groundwater-level changes indicated that a majority of the simulated groundwater-level changes were within 5 feet of the changes calculated from measured groundwater levels. Simulated groundwater-level rises generally were smaller than measured rises near surface-water irrigation districts. Simulated groundwater-level declines were larger than measured declines in several parts of the study area having large amounts of irrigated crops. Base-flow trends and volumes generally were reproduced by the simulation at most sites. Exceptions include downward trends of simulated

  11. Simulation of groundwater flow and the interaction of groundwater and surface water in the Willamette Basin and Central Willamette subbasin, Oregon

    Science.gov (United States)

    Herrera, Nora B.; Burns, Erick R.; Conlon, Terrence D.

    2014-01-01

    accounted for about 80 percent of that total. The upper 180 feet of productive aquifers in the Central Willamette and Southern Willamette subbasins produced about 70 percent of the total pumped volume. In this study, the USGS constructed a three-dimensional numerical finite-difference groundwater-flow model of the Willamette Basin representing the six hydrogeologic units, defined in previous investigations, as six model layers. From youngest to oldest, and [generally] uppermost to lowermost they are the: upper sedimentary unit, Willamette silt unit, middle sedimentary unit, lower sedimentary unit, Columbia River basalt unit, and basement confining unit. The high Cascade unit is not included in the groundwater-flow model because it is not present within the model boundaries. Geographic boundaries are simulated as no-flow (no water flowing in or out of the model), except where the Columbia River is simulated as a constant hydraulic head boundary. Streams are designated as head-dependent-flux boundaries, in which the flux depends on the elevation of the stream surface. Groundwater recharge from precipitation was estimated using the Precipitation-Runoff Modeling System (PRMS), a watershed model that accounts for evapotranspiration from the unsaturated zone. Evapotranspiration from the saturated zone was not considered an important component of groundwater discharge. Well pumping was simulated as specified flux and included public supply, irrigation, and industrial pumping. Hydraulic conductivity values were estimated from previous studies through aquifer slug and permeameter tests, specific capacity data, core analysis, and modeling. Upper, middle and lower sedimentary unit horizontal hydraulic conductivity values were differentiated between the Portland subbasin and the Tualatin, Central Willamette, and Southern Willamette subbasins based on preliminary model results.

  12. Regional Groundwater Flow Assessment in a Prospective High-Level Radioactive Waste Repository of China

    Directory of Open Access Journals (Sweden)

    Xiaoyuan Cao

    2017-07-01

    Full Text Available The production of nuclear energy will result in high-level radioactive waste (HLRW, which brings potential environmental dangers. Selecting a proper disposal repository is a crucial step in the development of nuclear energy. This paper introduces firstly the hydrogeological conditions of the Beishan area in China. Next, a regional groundwater model is constructed using a multiphase flow simulator to analyze the groundwater flow pattern in the Beishan area. Model calibration shows that the simulated and observed hydraulic heads match well, and the simulated regional groundwater flow pattern is similar to the surface flow pattern from the channel network, indicating that the groundwater flow is mainly dependent on the topography. In addition, the simulated groundwater storage over the period from 2003 to 2014 is similar to the trend derived from the Gravity Recovery and Climate Experiment satellite-derived results. Last, the established model is used to evaluate the influences of the extreme climate and regional faults on the groundwater flow pattern. It shows that they do not have a significant influence on the regional groundwater flow patterns. This study will provide a preliminary reference for the regional groundwater flow assessment in the site of the HLRW in China.

  13. Groundwater flow modelling in the upper Anga'a river watershed ...

    African Journals Online (AJOL)

    The Anga'a River watershed is located within the Yaounde IV district, South-east of Yaounde City, Cameroon. The groundwater flow and particle tracking modelling was carried out to determine in detail the groundwater flow and particle migration in the shallow unconfined aquifer of the Upper Anga'a river watershed.

  14. ENVIRONMENTAL RESEARCH BRIEF : ANALYTIC ELEMENT MODELING OF GROUND-WATER FLOW AND HIGH PERFORMANCE COMPUTING

    Science.gov (United States)

    Several advances in the analytic element method have been made to enhance its performance and facilitate three-dimensional ground-water flow modeling in a regional aquifer setting. First, a new public domain modular code (ModAEM) has been developed for modeling ground-water flow ...

  15. Groundwater flow near the Shoal Site, Sand Springs Range, Nevada: Impact of density-driven flow

    Energy Technology Data Exchange (ETDEWEB)

    Chapman, J.; Mihevc, T.; McKay, A.

    1994-09-01

    The nature of flow from a highland recharge area in a mountain range in north-central Nevada to discharge areas on either side of the range is evaluated to refine a conceptual model of contaminant transport from an underground nuclear test conducted beneath the range. The test, known as the Shoal event, was conducted in 1963 in granitic rocks of the Sand Springs Range. Sparse hydraulic head measurements from the early 1960s suggest flow from the shot location to the east to Fairview Valley, while hydrochemistry supports flow to salt pans in Fourmile Flat to the west. Chemical and isotopic data collected from water samples and during well-logging arc best explained by a reflux brine system on the west side of the Sand Springs Range, rather than a typical local flow system where all flow occurs from recharge areas in the highlands to a central discharge area in a playa. Instead, dense saline water from the playa is apparently being driven toward the range by density contrasts. The data collected between the range and Fourmile Flat suggest the groundwater is a mixture of younger, fresher recharge water with older brine. Chemical contrasts between groundwater in the east and west valleys reflect the absence of re-flux water in Fairview Valley because the regional discharge area is distant and thus there is no accumulation of salts. The refluxing hydraulic system probably developed after the end of the last pluvial period and differences between the location of the groundwater divide based on hydraulic and chemical indicators could reflect movement of the divide as the groundwater system adjusts to the new reflux condition.

  16. Scale problems in assessment of hydrogeological parameters of groundwater flow models

    Directory of Open Access Journals (Sweden)

    Nawalany Marek

    2015-09-01

    Full Text Available An overview is presented of scale problems in groundwater flow, with emphasis on upscaling of hydraulic conductivity, being a brief summary of the conventional upscaling approach with some attention paid to recently emerged approaches. The focus is on essential aspects which may be an advantage in comparison to the occasionally extremely extensive summaries presented in the literature. In the present paper the concept of scale is introduced as an indispensable part of system analysis applied to hydrogeology. The concept is illustrated with a simple hydrogeological system for which definitions of four major ingredients of scale are presented: (i spatial extent and geometry of hydrogeological system, (ii spatial continuity and granularity of both natural and man-made objects within the system, (iii duration of the system and (iv continuity/granularity of natural and man-related variables of groundwater flow system. Scales used in hydrogeology are categorised into five classes: micro-scale – scale of pores, meso-scale – scale of laboratory sample, macro-scale – scale of typical blocks in numerical models of groundwater flow, local-scale – scale of an aquifer/aquitard and regional-scale – scale of series of aquifers and aquitards. Variables, parameters and groundwater flow equations for the three lowest scales, i.e., pore-scale, sample-scale and (numerical block-scale, are discussed in detail, with the aim to justify physically deterministic procedures of upscaling from finer to coarser scales (stochastic issues of upscaling are not discussed here. Since the procedure of transition from sample-scale to block-scale is physically well based, it is a good candidate for upscaling block-scale models to local-scale models and likewise for upscaling local-scale models to regional-scale models. Also the latest results in downscaling from block-scale to sample scale are briefly referred to.

  17. Groundwater flow modelling of the excavation and operational phases - Forsmark

    International Nuclear Information System (INIS)

    Svensson, Urban; Follin, Sven

    2010-07-01

    As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different climate conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The modelling study reported here presents calculated inflow rates, drawdown of the groundwater table and upconing of deep saline water for different levels of grouting efficiency during the excavation and operational phases of a final repository at Forsmark. The inflow calculations are accompanied by a sensitivity study, which among other matters handles the impact of parameter heterogeneity, different deposition hole rejection criteria, and the SFR facility (the repository for short-lived radioactive waste located approximately 1 km to the north of the investigated candidate area for a final repository at Forsmark). The report also presents tentative modelling results for the duration of the saturation phase, which starts once the used parts of the repository are being backfilled

  18. Radionuclide transport by groundwater flow through the geosphere: current status

    International Nuclear Information System (INIS)

    Lever, D.A.

    1989-02-01

    The geosphere is an important barrier retaining radionuclides that have been released from the near field of a waste repository and retarding their return to Man. The assessment models that are used in the current Nirex assessments to describe the groundwater flow in the vicinity of the repository and the transport of radionuclides by the groundwater are summarized, and their data requirements are set out. The Nirex research programme is designed to provide improved and additional data for these models, to deepen the understanding of the important processes and to develop improved models to describe them. This document outlines the status of the assessment models and associated research programme in the spring of 1988. The programme complements existing knowledge in this field. Key areas are measurements of the physical properties of rocks, field and modelling studies of fractured rocks, measurements of sorption onto geological materials, investigation of the possible importance of colloid transport and saline interfaces, transport of naturally occurring elements over geological time-scales in natural geochemical systems, and participation in an international model validation exercise. (author)

  19. Groundwater flow modelling of the excavation and operational phases - Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Svensson, Urban (Computer-aided Fluid Engineering AB, Lyckeby (Sweden)); Follin, Sven (SF GeoLogic AB, Taeby (Sweden))

    2010-07-15

    As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different climate conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The modelling study reported here presents calculated inflow rates, drawdown of the groundwater table and upconing of deep saline water for different levels of grouting efficiency during the excavation and operational phases of a final repository at Forsmark. The inflow calculations are accompanied by a sensitivity study, which among other matters handles the impact of parameter heterogeneity, different deposition hole rejection criteria, and the SFR facility (the repository for short-lived radioactive waste located approximately 1 km to the north of the investigated candidate area for a final repository at Forsmark). The report also presents tentative modelling results for the duration of the saturation phase, which starts once the used parts of the repository are being backfilled.

  20. Groundwater ages from the freshwater zone of the Edwards aquifer, Uvalde County, Texas—Insights into groundwater flow and recharge

    Science.gov (United States)

    Hunt, Andrew G.; Landis, Gary P.; Faith, Jason R.

    2016-02-23

    Tritium–helium-3 groundwater ages of the Edwards aquifer in south-central Texas were determined as part of a long-term study of groundwater flow and recharge in the Edwards and Trinity aquifers. These ages help to define groundwater residence times and to provide constraints for calibration of groundwater flow models. A suite of 17 samples from public and private supply wells within Uvalde County were collected for active and noble gases, and for tritium–helium-3 analyses from the confined and unconfined parts of the Edwards aquifer. Samples were collected from monitoring wells at discrete depths in open boreholes as well as from integrated pumped well-head samples. The data indicate a fairly uniform groundwater flow system within an otherwise structurally complex geologic environment comprised of regionally and locally faulted rock units, igneous intrusions, and karst features within carbonate rocks. Apparent ages show moderate, downward average, linear velocities in the Uvalde area with increasing age to the east along a regional groundwater flow path. Though the apparent age data show a fairly consistent distribution across the study area, many apparent ages indicate mixing of both modern (less than 60 years) and premodern (greater than 60 years) waters. This mixing is most evident along the “bad water” line, an arbitrary delineation of 1,000 milligrams per liter dissolved solids that separates the freshwater zone of the Edwards aquifer from the downdip saline water zone. Mixing of modern and premodern waters also is indicated within the unconfined zone of the aquifer by high excess helium concentrations in young waters. Excess helium anomalies in the unconfined aquifer are consistent with possible subsurface discharge of premodern groundwater from the underlying Trinity aquifer into the younger groundwater of the Edwards aquifer.

  1. Analysis and integrated modelling of groundwater infiltration to sewer networks

    DEFF Research Database (Denmark)

    Thorndahl, Søren Liedtke; Balling, Jonas Dueholm; Larsen, Uffe Bay Bøgh

    2016-01-01

    Infiltration of groundwater to sewer systems is a problem for the capacity of the system as well as for treatment processes at waste water treatment plants. This paper quantifies the infiltration of groundwater to a sewer system in Frederikshavn Municipality, Denmark, by measurements of sewer flow...... and novel model set-up, which simulates the interaction between groundwater and sewer flow. The study area has a separate waste water sewer system, but the discharged volumes from the system are approximately twice the volumes from a tight system without infiltration. The model set-up makes use of two...... commercial models: MIKE SHE for simulation of groundwater transport and MIKE URBAN (MOUSE) [DHI, Hørsholm, Denmark] for simulation of sewer flow. By simulating the groundwater level and calibrating infiltration coefficients against sewer flow measurements, it has been possible to estimate the average...

  2. Modelling of groundwater flow and solute transport in Olkiluoto. Update 2008

    International Nuclear Information System (INIS)

    Loefman, J.; Pitkaenen, P.; Meszaros, F.; Keto, V.; Ahokas, H.

    2009-10-01

    Posiva Oy is preparing for the final disposal of spent nuclear fuel in the crystalline bedrock in Finland. Olkiluoto in Eurajoki has been selected as the primary site for the repository, subject to further detailed characterisation which is currently focused on the construction of an underground rock characterisation and research facility (the ONKALO). An essential part of the site investigation programme is analysis of the deep groundwater flow by means of numerical flow modelling. This study is the latest update concerning the site-scale flow modelling and is based on all the hydrogeological data gathered from field investigations by the end of 2007. The work is divided into two separate modelling tasks: 1) characterization of the baseline groundwater flow conditions before excavation of the ONKALO, and 2) a prediction/outcome (P/O) study of the potential hydrogeological disturbances due to the ONKALO. The flow model was calibrated by using all the available data that was appropriate for the applied, deterministic, equivalent porous medium (EPM) / dual-porosity (DP) approach. In the baseline modelling, calibration of the flow model focused on improving the agreement between the calculated results and the undisturbed observations. The calibration resulted in a satisfactory agreement with the measured pumping test responses, a very good overall agreement with the observed pressures in the deep drill holes and a fairly good agreement with the observed salinity. Some discrepancies still remained in a few single drill hole sections, because the fresh water infiltration in the model tends to dilute the groundwater too much at shallow depths. In the P/O calculations the flow model was further calibrated by using the monitoring data on the ONKALO disturbances. Having significantly more information on the inflows to the tunnel (compared with the previous study) allowed better calibration of the model, which allowed it to capture very well the observed inflow, the

  3. Groundwater Flow and Transport Model in Cecina Plain (Tuscany, Italy using GIS processing

    Directory of Open Access Journals (Sweden)

    Riccardo Armellini

    2015-03-01

    Full Text Available This work provides a groundwater flow and transport model of trichlorethylene and tetrachlorethylene contamination in the Cecina’s coastal aquifer. The contamination analysis, with source located in the Poggio Gagliardo area (Montescudaio, Pisa, was necessary to optimize the groundwater monitoring and remediation design. The work was carried out in two phases: • design of a conceptual model of the aquifer using GIS analysis of many stratigraphic, chemical and hydrogeological data, collected from 2004 to 2012 in six aqueduct wells; • implementation of a groundwater flow and transport numerical model using the MODFLOW 88/96 and MT3D code and the graphical user interface GroundWaterVistas 5. The conceptual model hypothesizes a multilayer aquifer in the coastal plain extended to the sandy-clay hills, recharged by rainfall and by the Cecina River. The aquifer shows important hydrodynamic features affecting both the contamination spreading, due to the presence of a perched and heavily polluted layer separate from the underlying productive aquifer, and the hydrological balance, due to a thick separation layer that limits exchanges between the river and the second groundwater aquifer. The numerical model, built using increasingly complex versions of the initial conceptual model, has been calibrated using monitoring surveys conducted by the Environmental Protection Agency of Regione Toscana (ARPAT, in order to obtain possible forecast scenarios based on the minimum and maximum flow periods, and it is currently used as a tool for decision support regarding the reclamation and/or protection of the aquifer. Future developments will regard the implementation of the multilayer transport model, based on a new survey, and the final coupling with the regional hydrological model named MOBIDIC.

  4. Stochastic modelling of groundwater flow at the WIPP site

    International Nuclear Information System (INIS)

    Cliffe, K.A.; Jackson, C.P.

    1993-01-01

    A stochastic approach to modelling the groundwater flow in the vicinity of the WIPP site in New Mexico is described. A geostatistical model of the transmissivity of the Culebra dolomite was constructed on the basis of experimental measurements. The uncertainty in various quantities of interest in a repository performance assessment, such as the time to travel to the boundary of the model domain, were studied using a Monte-Carlo technique. The results indicate that conditioning the transmissivity on the measured values can lead to a significant reduction in uncertainty. The issue of validation of statistical models is also addressed. Several statistical tests were applied to the models and it is suggested that hypothesis testing can be a useful technique for validation

  5. wrv: An R Package for Groundwater Flow Model Construction, Wood River Valley Aquifer System, Idaho

    Science.gov (United States)

    Fisher, J. C.

    2014-12-01

    Groundwater models are one of the main tools used in the hydrogeological sciences to assess resources and to simulate possible effects from future water demands and changes in climate. The hydrological inputs to groundwater models can be numerous and can vary in both time and space. Difficulties associated with model construction are often related to extensive datasets and cumbersome data processing tasks. To mitigate these difficulties, a graphical user interface (GUI) is often employed to aid the input of data for creating models. Unfortunately, GUI software presents an obstacle to reproducibility, a cornerstone of research. The considerable effort required to document processing steps in a GUI program, and the rapid obsoleteness of these steps with subsequent versions of the software, has prompted modelers to explicitly write down processing steps as source code to make them 'easily' reproducible. This research describes the R package wrv, a collection of datasets and functions for pre- and post-processing the numerical groundwater flow model of the Wood River Valley aquifer system, south-central Idaho. R largely facilitates reproducible modeling with the package vignette; a document that is a combination of content and source code. The code is run when the vignette is built, and all data analysis output (such as figures and tables) is created on the fly and inserted into the final document. The wrv package includes two vignettes that explain and run steps that (1) create package datasets from raw data files located on a publicly accessible repository, and (2) create and run the groundwater flow model. MODFLOW-USG, the numerical groundwater model used in this study, is executed from the vignette, and model output is returned for exploratory analyses. The ability of R to perform all processing steps in a single workflow is attributed to its comprehensive list of features; that include geographic information system and time series functionality.

  6. Contaminant Transport Parameters for the Groundwater Flow and Contaminant Transport Model of Corrective Action Units 101 and 102: Central and Western Pahute Mesa, Nye County, Nevada, Revision 0

    Energy Technology Data Exchange (ETDEWEB)

    Drici, Warda [International Technologies Corporation, Las Vegas, NV (United States)

    2003-08-01

    This report documents the analysis of the available transport parameter data conducted in support of the development of a Corrective Action Unit (CAU) groundwater flow model for Central and Western Pahute Mesa: CAUs 101 and 102.

  7. Hydrologic Data for the Groundwater Flow and Contaminant Transport Model of Corrective Action Units 101 and 102: Central and Western Pahute Mesa, Nye County, Nevada, Revision 0

    Energy Technology Data Exchange (ETDEWEB)

    Drici, Warda [Stoller-Navarro Joint Venture, Las Vegas, NV (United States)

    2004-02-01

    This report documents the analysis of the available hydrologic data conducted in support of the development of a Corrective Action Unit (CAU) groundwater flow model for Central and Western Pahute Mesa: CAUs 101 and 102.

  8. Variable thickness transient groundwater flow model theory and numerical implementation

    International Nuclear Information System (INIS)

    Kipp, K.L.; Reisenauer, A.E.; Cole, C.R.; Bryan, C.A.

    1976-01-01

    Modeling of radionuclide movement in the groundwater system beneath the Hanford Reservation requires mathematical simulation of the two-dimensional flow in the unconfined aquifer. This was accomplished using the nonlinear, transient Boussinesq equation with appropriate initial and boundary conditions, including measured Columbia River stages and rates of wastewater disposal to the ground. The heterogeneous permeability (hydraulic conductivity) distribution was derived by solution of the Boussinesq equation along instantaneous streamtubes of flow employing a measured water table surface and a limited number of field-measured hydraulic conductivity values. Use of a successive line over-relaxation technique with unequal time steps resulted in a more rapid convergence of the numerical solution than with previous techniques. The model was used to simulate the water table changes for the period 1968 through 1973 using known inputs and boundary conditions. A comparison of calculated and measured water table elevations was made at specific well locations and the quality of the verification simulation was evaluated using a data retrieval and display system. Agreement between the model results and measured data was good over two-thirds of the Hanford Reservation. The capability of the model to simulate flow with time-varying boundary conditions, complex boundary shapes, and a heterogeneous distribution of aquifer properties was demonstrated

  9. Signal flow analysis

    CERN Document Server

    Abrahams, J R; Hiller, N

    1965-01-01

    Signal Flow Analysis provides information pertinent to the fundamental aspects of signal flow analysis. This book discusses the basic theory of signal flow graphs and shows their relation to the usual algebraic equations.Organized into seven chapters, this book begins with an overview of properties of a flow graph. This text then demonstrates how flow graphs can be applied to a wide range of electrical circuits that do not involve amplification. Other chapters deal with the parameters as well as circuit applications of transistors. This book discusses as well the variety of circuits using ther

  10. Groundwater.

    Science.gov (United States)

    Braids, Olin C.; Gillies, Nola P.

    1978-01-01

    Presents a literature review of groundwater quality covering publications of 1977. This review includes: (1) sources of groundwater contamination; and (2) management of groundwater. A list of 59 references is also presented. (HM)

  11. An Integrated Approach on Groundwater Flow and Heat/Solute Transport for Sustainable Groundwater Source Heat Pump (GWHP) System Operation

    Science.gov (United States)

    Park, D. K.; Bae, G. O.; Joun, W.; Park, B. H.; Park, J.; Park, I.; Lee, K. K.

    2015-12-01

    The GWHP system uses a stable temperature of groundwater for cooling and heating in buildings and thus has been known as one of the most energy-saving and cost-efficient renewable energy techniques. A GWHP facility was installed at an island located at the confluence of North Han and South Han rivers, Korea. Because of well-developed alluvium, the aquifer is suitable for application of this system, extracting and injecting a large amount of groundwater. However, the numerical experiments under various operational conditions showed that it could be vulnerable to thermal interference due to the highly permeable gravel layer, as a preferential path of thermal plume migration, and limited space for well installation. Thus, regional groundwater flow must be an important factor of consideration for the efficient operation under these conditions but was found to be not simple in this site. While the groundwater level in this site totally depends on the river stage control of Paldang dam, the direction and velocity of the regional groundwater flow, observed using the colloidal borescope, have been changed hour by hour with the combined flows of both the rivers. During the pumping and injection tests, the water discharges in Cheongpyeong dam affected their respective results. Moreover, the measured NO3-N concentrations might imply the effect of agricultural activities around the facility on the groundwater quality along the regional flow. It is obvious that the extraction and injection of groundwater during the facility operation will affect the fate of the agricultural contaminants. Particularly, the gravel layer must also be a main path for contaminant migration. The simulations for contaminant transport during the facility operation showed that the operation strategy for only thermal efficiency could be unsafe and unstable in respect of groundwater quality. All these results concluded that the integrated approach on groundwater flow and heat/solute transport is necessary

  12. BGS GISGroundwater: the first numerical seamless GIS groundwater flow model

    OpenAIRE

    Wang, Lei; Jackson, Christopher; Kingdon, Andrew; Pachocka, Magdalena

    2013-01-01

    Geographic Information Systems (GISs) are the major data sources for numerical groundwater modelling, and it is common practice to couple groundwater models with GISs. There are three methods for coupling the numerical groundwater models with GISs, namely, “loose”, “tight”, and “seamless”. A seamless GIS groundwater model allows constructing, running model and visualisation of modelled results to be carried out all in a GIS environment, thus having the advantages of being easy to use and high...

  13. Hydrogeology and simulation of groundwater flow in the Central Oklahoma (Garber-Wellington) Aquifer, Oklahoma, 1987 to 2009, and simulation of available water in storage, 2010–2059

    Science.gov (United States)

    Mashburn, Shana L.; Ryter, Derek W.; Neel, Christopher R.; Smith, S. Jerrod; Magers, Jessica S.

    2014-02-10

    The Central Oklahoma (Garber-Wellington) aquifer underlies about 3,000 square miles of central Oklahoma. The study area for this investigation was the extent of the Central Oklahoma aquifer. Water from the Central Oklahoma aquifer is used for public, industrial, commercial, agricultural, and domestic supply. With the exception of Oklahoma City, all of the major communities in central Oklahoma rely either solely or partly on groundwater from this aquifer. The Oklahoma City metropolitan area, incorporating parts of Canadian, Cleveland, Grady, Lincoln, Logan, McClain, and Oklahoma Counties, has a population of approximately 1.2 million people. As areas are developed for groundwater supply, increased groundwater withdrawals may result in decreases in long-term aquifer storage. The U.S. Geological Survey, in cooperation with the Oklahoma Water Resources Board, investigated the hydrogeology and simulated groundwater flow in the aquifer using a numerical groundwater-flow model. The purpose of this report is to describe an investigation of the Central Oklahoma aquifer that included analyses of the hydrogeology, hydrogeologic framework of the aquifer, and construction of a numerical groundwater-flow model. The groundwater-flow model was used to simulate groundwater levels and for water-budget analysis. A calibrated transient model was used to evaluate changes in groundwater storage associated with increased future water demands.

  14. Estimation and impact assessment of input and parameter uncertainty in predicting groundwater flow with a fully distributed model

    Science.gov (United States)

    Touhidul Mustafa, Syed Md.; Nossent, Jiri; Ghysels, Gert; Huysmans, Marijke

    2017-04-01

    Transient numerical groundwater flow models have been used to understand and forecast groundwater flow systems under anthropogenic and climatic effects, but the reliability of the predictions is strongly influenced by different sources of uncertainty. Hence, researchers in hydrological sciences are developing and applying methods for uncertainty quantification. Nevertheless, spatially distributed flow models pose significant challenges for parameter and spatially distributed input estimation and uncertainty quantification. In this study, we present a general and flexible approach for input and parameter estimation and uncertainty analysis of groundwater models. The proposed approach combines a fully distributed groundwater flow model (MODFLOW) with the DiffeRential Evolution Adaptive Metropolis (DREAM) algorithm. To avoid over-parameterization, the uncertainty of the spatially distributed model input has been represented by multipliers. The posterior distributions of these multipliers and the regular model parameters were estimated using DREAM. The proposed methodology has been applied in an overexploited aquifer in Bangladesh where groundwater pumping and recharge data are highly uncertain. The results confirm that input uncertainty does have a considerable effect on the model predictions and parameter distributions. Additionally, our approach also provides a new way to optimize the spatially distributed recharge and pumping data along with the parameter values under uncertain input conditions. It can be concluded from our approach that considering model input uncertainty along with parameter uncertainty is important for obtaining realistic model predictions and a correct estimation of the uncertainty bounds.

  15. Methods of investigation and analysis on groundwater using radon as an indicator

    International Nuclear Information System (INIS)

    Hamada, Hiromasa; Imaizumi, Masayuki; Komae, Takami

    1997-01-01

    As for groundwater, the quality is good, and the temperature is constant throughout year, further, it can be easily utilized only by digging wells. The quantity of its utilization in one year is about 20% of total water utilization, and about 17 billion m 3 . Recently in Japan, the frequency of occurrence of water shortage is high, and the supply of river water is unstable, therefore, the importance of groundwater increased. It is indispensable to grasp in detail the state of groundwater flow as groundwater pollution is actualized, and the water quality has become problem. As the principle that radon becomes the index for groundwater analysis, the physical characteristic of radon and the features of the radon in groundwater are explained. The method of measuring radon concentration in groundwater and surface water is described. The investigation and analysis methods, to which the processes of radon formation and radon decay are applied, in which the equilibrium radon concentration in groundwater is used as the index, to which the relation of the degree of saturation in aquifer to the radon concentration in liquid phase is applied, and to which the difference of the concentrations in surface water and groundwater is applied, are reported. (K.I.)

  16. Integrating Electrical Analogy and Computer Modeling of Groundwater Flow for Teaching Flownet Concepts

    Directory of Open Access Journals (Sweden)

    Murthy Kasi

    2013-10-01

    Full Text Available Laplace equation is the basic differential equation that governs the steady flow of a fluid through an isotropic and homogeneous porous medium and also the steady flow of current in a conducting medium. Therefore, a steady-state groundwater flow problem can be formulated as an analogous electrical current flow problem. A flow net, set of grids formed by orthogonally intersecting equipotential lines and flow lines, is a graphical solution to the equations of steady groundwater flow. By definition, flownet for the original groundwater problem and the corresponding analogous electrical problem should be similar. This feature allows the possibility of introducing the concepts of flownets to students using the easily demonstrable electrical counterpart of the problem in a laboratory setting. This paper discusses the efforts of the authors to widen the scope of an experiment already included in the Fluid Mechanics laboratory course of a Civil Engineering curriculum and to better teach flownet principles using the electrical analogy of groundwater flow problems. Students used a simple experimental setup to obtain flownets for selected groundwater flow situations with different boundary conditions using the electrical analogy concept. Students also used a groundwater flow computer model to obtain flownets for the same flow situations and compared the results. The laboratory lesson plan consisted of five steps: (i study and understand the selected physical groundwater problems, (ii conceptualize the corresponding analogous electrical problems (iii use the electrical analogy experimental setup to obtain flownets, (iv study and understand the mathematical formulation of the problems, and (v compare the analogous results with those obtained from a groundwater flow computer model. Sample results obtained by students are presented. The student feedback indicated that this approach resulted in an effective learning of the concepts involved.

  17. Analysis of groundwater from deep boreholes in Gideaa

    International Nuclear Information System (INIS)

    Laurent, S.

    1983-03-01

    Groundwaters from two boreholes in granitic rock at an ivestigation site in Gideaa has been sampled and analysed. This is part of a larger program of geological, geophysical and hydrogeological investigations aimed at finding a suitable site for a high level radioactive waste respository. Five water-bearing levels in each borehole down to the deepest at about 500 m in the first and about 600 m in the second borehole were selected. Prior to sampling, the waterbearing level is isolated between packer sleeves. The water is then pumped to the surface where sensitive parameters such as redox potential, pH, sulphide and oxygen content are measured electrochemically on the flowing water in a system isolated from the air. Water, filter and gas samples are sent to several laboratories for further analysis. The present report is a presentation of the groundwater analysis. The reliability of the results is discussed but there is no evaluation relation to geology and hydrogeology. This report presents the basic results from the groundwater analyses to be further evaluated by experts in different fields. (Forf)

  18. Simulation of regional ground-water flow in the Cambrian-Ordovician aquifer system in the northern Midwest, United States: in Regional aquifer-system analysis

    Science.gov (United States)

    Mandle, R.J.; Kontis, A.L.

    1992-01-01

    A six-State area in the northern Midwest of the United States has become increasingly dependent on ground water from the Cambrian-Ordovician aquifer system, which consists of a sequence of sandstones, carbonate rocks, and shales. Ground-water withdrawals from the aquifer system began in the late 1800's and increased to approximately 684 million gallons per day (1,058 cubic feet per second) by 1980. This withdrawal has caused more than 900 feet of decline in the potentiometric surface of the aquifer system in parts of the Chicago, Ill., area. Pumping in Minneapolis-St. Paul, Minn., Milwaukee, Wis., and central Iowa has produced a few hundreds of feet of water-level decline.

  19. Groundwater flow modelling of periods with periglacial and glacial climate conditions - Laxemar

    Energy Technology Data Exchange (ETDEWEB)

    Vidstrand, Patrik (TerraSolve AB, Floda (Sweden)); Rhen, Ingvar (SWECO Environment AB, Falun (Sweden)); Zugec, Nada (Bergab, Goeteborg (Sweden))

    2010-12-15

    As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. This report is concerned with the modelling of a repository at the Laxemar-Simpevarp site during periglacial and glacial climate conditions as a comparison to corresponding modelling carried out for Forsmark /Vidstrand et al. 2010/. The groundwater flow modelling study reported here comprises a coupled thermal-hydraulic-chemical (T-H-C) analysis of periods with periglacial and glacial climate conditions. The objective of the report is to provide bounding hydrogeological estimates at different stages during glaciation and deglaciation of a glacial cycle at Laxemar. Three cases with different climate conditions are analysed here: (i) Temperate case, (ii) Glacial case without permafrost, and (iii) Glacial case with permafrost. The glacial periods are transient and encompass approximately 13,000 years. The simulation results comprise pressures, Darcy fluxes, and water salinities, as well as advective transport performance measures obtained by particle tracking such as flow path lengths, travel times and flow-related transport resistances. The modelling is accompanied by a sensitivity study that addresses the impact of the following matters: the direction of the ice sheet advance and the bedrock hydraulic and transport properties

  20. Impact of Groundwater Flow and Energy Load on Multiple Borehole Heat Exchangers.

    Science.gov (United States)

    Dehkordi, S Emad; Schincariol, Robert A; Olofsson, Bo

    2015-01-01

    The effect of array configuration, that is, number, layout, and spacing, on the performance of multiple borehole heat exchangers (BHEs) is generally known under the assumption of fully conductive transport. The effect of groundwater flow on BHE performance is also well established, but most commonly for single BHEs. In multiple-BHE systems the effect of groundwater advection can be more complicated due to the induced thermal interference between the boreholes. To ascertain the influence of groundwater flow and borehole arrangement, this study investigates single- and multi-BHE systems of various configurations. Moreover, the influence of energy load balance is also examined. The results from corresponding cases with and without groundwater flow as well as balanced and unbalanced energy loads are cross-compared. The groundwater flux value, 10(-7) m/s, is chosen based on the findings of previous studies on groundwater flow interaction with BHEs and thermal response tests. It is observed that multi-BHE systems with balanced loads are less sensitive to array configuration attributes and groundwater flow, in the long-term. Conversely, multi-BHE systems with unbalanced loads are influenced by borehole array configuration as well as groundwater flow; these effects become more pronounced with time, unlike when the load is balanced. Groundwater flow has more influence on stabilizing loop temperatures, compared to array characteristics. Although borehole thermal energy storage (BTES) systems have a balanced energy load function, preliminary investigation on their efficiency shows a negative impact by groundwater which is due to their dependency on high temperature gradients between the boreholes and surroundings. © 2014, National Ground Water Association.

  1. Hydrogeochemical processes identification and groundwater pollution causes analysis in the northern Ordos Cretaceous Basin, China.

    Science.gov (United States)

    An, Yongkai; Lu, Wenxi

    2017-10-23

    It is necessary to identify the hydrogeochemical processes and analyze the causes of groundwater pollution due to the lack of knowledge about the groundwater chemical characteristics and the endemic diseases caused by groundwater pollution in the northern Ordos Cretaceous Basin. In this paper, groundwater chemical facies were obtained using the piper trilinear diagram based on the analysis of 190 samples. The hydrogeochemical processes were identified using ionic ratio coefficient, such as leaching, evaporation and condensation. The causes and sources of groundwater pollution were analyzed by correspondence analysis, and the spatial distribution and enrichment reasons of fluoride ion were analyzed considering the endemic fluorosis emphatically. The results show that leaching, evaporation and condensation, mixing, and anthropogenic activities all had significant impact on hydrogeochemical processes in the study area. However, cation exchange and adsorption effects were strong in the S2 and S3 groundwater flow systems, but weak in S1. Groundwater is mainly polluted by Mn and COD Mn in the study area. The landfill leachate, domestic sewage, and other organic pollutants, excessive use of pesticides and fertilizers in agriculture, and pyrite oxidation from long-term and large-scale exploitation of coal are the sources of groundwater pollution. The S1 has the highest degree of groundwater pollution, followed by S2 and S3. High concentration of fluoride ion is mainly distributed in the north and west of study area. Evaporation and condensation and groundwater chemistry component are the most important causes of fluoride ion enrichment. The results obtained in this study will be useful for understanding the groundwater quality for effective management and utilization of groundwater resources and assurance of drinking water safety.

  2. Groundwater Flow Modeling in the KURT site for a Case Study about a Hypothetical Geological Disposal Facility of Radioactive Wastes

    International Nuclear Information System (INIS)

    Ko, Nak Youl; Park, Kyung Woo; Kim, Kyung Su; Choi, Jong Won

    2012-01-01

    Groundwater flow simulations were performed to obtain data of groundwater flow used in a safety assessment for a hypothetical geological disposal facility assumed to be located in the KURT (KAERI Underground Research Tunnel) site. A regional scale modeling of the groundwater flow system was carried out to make boundary conditions for a local scale modeling. And, fracture zones identified at the study site were involved in the local scale groundwater flow model. From the results of the local scale modeling, a hydraulic head distribution was indicated and it was used in a particle tracking simulation for searching pathway of groundwater from the location of the hypothetical disposal facility to the surface where the groundwater reached. The flow distance and discharge rate of the groundwater in the KURT site were calculated. It was thought that the modeling methods used in this study was available to prepare the data of groundwater flow in a safety assessment for a geological disposal facility of radioactive wastes.

  3. Groundwater flow system in the valley of Toluca, Mexico: an assay of natural radionuclide specific activities

    Energy Technology Data Exchange (ETDEWEB)

    Segovia, N.; Tamez, E.; Pena, P.; Acosta, E.; Iturbe, J.L. [ININ, Mexico D.F. (Mexico); Carrillo, J. [UACPyP-CCH, UNAM, Mexico D.F. (Mexico); Armienta, M.A. [IGFUNAM, C. Universitaria, Mexico D.F. (Mexico)

    1999-03-01

    Natural radionuclides and physicochemical parameters have been evaluated in groundwater samples from boreholes belonging to the drinking water supply system of the Toluca City, Mexico. The results obtained for radon and radium, together with the physicochemical parameters of the studied samples, indicate a fast and efficient recharge pattern. The presence of a local and a regional groundwater flows was also observed. The local flow belongs to shallower water, recognized by its low radon content and dissolved ions, as compared with the regional, deeper groundwater flow with a longer residence time.

  4. Controls on Groundwater Flow in an Alpine Talus-Moraine Complex

    Science.gov (United States)

    Muir, D. L.; Hayashi, M.; Bentley, L. R.

    2009-05-01

    Since alpine watersheds are the headwaters of rivers acting as major sources of water, there is growing concern over water shortages in areas dependent on mountain runoff. Talus and moraine complexes, as well as fractured bedrock, are a dominant hydrologic response unit within the Lake O'Hara Research Basin (LORB) in Yoho National Park, British Columbia. In this alpine environment, previous studies have shown that groundwater plays an important hydrological role. Although little is known about groundwater storage in these media, they are likely a significant groundwater reservoir and an important control on groundwater flow. The goals of this study are to develop a conceptual model of the talus and moraine complex and the fractured bedrock. The approximately 0.3km2 Babylon drainage basin within the LORB was chosen as the study site as it contains a talus and moraine complex that drains into one gaugeable stream. The conceptual model of this basin has been developed using geophysical, hydrological and hydrogeological methods. Three Ground Penetrating Radar (GPR) and Electrical Resistivity Imaging (ERI) surveys were used to characterize the subsurface structure and water distribution within the talus and moraine complex. The bedrock surface is clearly defined in the GPR profiles and its elevation agrees with that in the ERI inversions. Highly resistive talus material is observable in the ERI results, and areas of low resistivity are found within the bedrock. Hydraulic conductivity estimates of the geologic media, calculated using tracer slug injection and baseflow recession analysis methods, fall within the ranges from gravel to fractured rock. Isotopic hydrograph separations indicate that groundwater is a significant contributor to stream discharge. Linear reservoir models show basin response times of up to 16 hours. The geophysical and hydrological evidence points toward two flow systems operating in the Babylon basin, those of flow through the fractured bedrock

  5. A conceptual framework of groundwater flow in some crystalline aquifers in Southeastern Ghana

    Science.gov (United States)

    Yidana, Sandow Mark; Ganyaglo, Samuel; Banoeng-Yakubo, Bruce; Akabzaa, Thomas

    2011-02-01

    A conceptual groundwater flow model was developed for the crystalline aquifers in southeastern part of the Eastern region, Ghana. The objective was to determine approximate levels of groundwater recharge, estimate aquifer hydraulic parameters, and then test various scenarios of groundwater extraction under the current conditions of recharge. A steady state groundwater flow model has been calibrated against measured water levels of 19 wells in the area. The resulting recharge is estimated to range from 8.97 × 10 -5 m/d to 7.14 × 10 -4 m/d resulting in a basin wide average recharge of about 9.6% of total annual precipitation, which results in a basin wide quantitative recharge of about 2.4 million m 3/d in the area. This compares to recharge estimated from the chloride mass balance of 7.6% of precipitation determined in this study. The general groundwater flow in the area has also been determined to conform to the general northeast-southwest structural grain of the country. The implication is that the general hydrogeology is controlled by post genetic structural entities imposed on the rocks to create ingresses for sufficient groundwater storage and transport. Calibrated aquifer hydraulic conductivities range between 0.99 m/d and over 19.4 m/d. There is a significant contribution of groundwater discharge to stream flow in the study area. Increasing groundwater extraction will have an effect on stream flow. This study finds that the current groundwater extraction levels represent only 0.17% of the annual recharge from precipitation, and that groundwater can sustain future increased groundwater demands from population growth and industrialization.

  6. Simulating the effect of climate extremes on groundwater flow through a lakebed

    Science.gov (United States)

    Virdi, Makhan L.; Lee, Terrie M.; Swancar, Amy; Niswonger, Richard G.

    2012-01-01

    Groundwater exchanges with lakes resulting from cyclical wet and dry climate extremes maintain lake levels in the environment in ways that are not well understood, in part because they remain difficult to simulate. To better understand the atypical groundwater interactions with lakes caused by climatic extremes, an original conceptual approach is introduced using MODFLOW-2005 and a kinematic-wave approximation to variably saturated flow that allows lake size and position in the basin to change while accurately representing the daily lake volume and three-dimensional variably saturated groundwater flow responses in the basin. Daily groundwater interactions are simulated for a calibrated lake basin in Florida over a decade that included historic wet and dry departures from the average rainfall. The divergent climate extremes subjected nearly 70% of the maximum lakebed area and 75% of the maximum shoreline perimeter to both groundwater inflow and lake leakage. About half of the lakebed area subject to flow reversals also went dry. A flow-through pattern present for 73% of the decade caused net leakage from the lake 80% of the time. Runoff from the saturated lake margin offset the groundwater deficit only about half of that time. A centripetal flow pattern present for 6% of the decade was important for maintaining the lake stage and generated 30% of all net groundwater inflow. Pumping effects superimposed on dry climate extremes induced the least frequent but most cautionary flow pattern with leakage from over 90% of the actual lakebed area.

  7. Influence of quick groundwater recharge on base flow in karstic catchments

    Science.gov (United States)

    Liu, Yan; Zarfl, Christiane; Basu, Nandita B.; Cirpka, Olaf A.

    2017-04-01

    Flow from karst springs is important for the groundwater flow and its recharge which, in turn can determine the pattern of base flow. This behaviour can be well observed in the Ammer catchment, located in southwestern Germany. It covers an area of approximately 130.5 km2 with several karst springs contributing most of the groundwater flow to the Ammer River. Its discharge shows a very special behaviour with a sharp increase every winter. It is supposed that the groundwater storage layer of this catchment can store large volumes of water because of karstification of the aquifers. Recharge from the subsurface storage to the groundwater storage when subsurface storage reaches a threshold makes groundwater storage increase rapidly, which is also reflected in a quickly rising base flow. We set up a semi-distributed hydrologic model to reproduce this behaviour and gain additional insights on the underlying processes of these discharge dynamics. The model is composed out of three main components: soil moisture, subsurface storage and groundwater storage. Besides percolation from subsurface storage to groundwater storage, quick recharge was introduced into this model for interpreting the sharp rise of base flow. This model was used for five years of simulation (from 2003 to 2007). Results indicate that: (a) percolation is an every day process whereas quick recharge only occurs over few days within a year, mostly from December to April and also in June when precipitation is very large; (b) the annual average recharge from percolation and quick recharge account for 18% and 82% of the total groundwater recharge, respectively, but the quick recharge rate is seven times higher than the percolation rate; and (c) for a single event of sharp increase in base flow quick recharge contributes 70%-78% to groundwater recharge, but in case of a single event of gradual increase of the base flow quick recharge contributes only 30%.

  8. Temperature distribution by the effect of groundwater flow in an aquifer thermal energy storage system model

    Science.gov (United States)

    Shim, B.

    2005-12-01

    Aquifer thermal energy storage (ATES) can be a cost-effective and renewable energy source, depending on site-specific thermohydraulic conditions. To design an effective ATES system, the understanding of thermohydraulic processes is necessary. The heat transfer phenomena of an aquifer heat storage system are simulated with the scenario of heat pump operation of pumping and waste water reinjection in a two layered confined aquifer model having the effect of groundwater movement. Temperature distribution of the aquifer model is generated, and hydraulic heads and temperature variations are monitored at both wells during simulation days. The average groundwater velocities are determined with two assumed hydraulic gradients set by boundary conditions, and the effect of groundwater flow are shown at the generated thermal distributions at three different depth slices. The generated temperature contour lines at the hydraulic gradient of 0.001 are shaped circular, and the center is moved less than 5 m to the east in 365 days. However at the hydraulic gradient of 0.01, the contour centers of the east well at each depth slice are moved near the east boundary and the movement of temperature distribution is increased at the lower aquifer. By the analysis of thermal interference data between two wells the efficiency of a heat pump operation model is validated, and the variation of heads is monitored at injection, pumping and stabilized state. The thermal efficiency of the ATES system model is represented as highly depended on groundwater flow velocity and direction. Therefore the hydrogeologic condition for the system site should be carefully surveyed.

  9. Fracture distribution determined by borehole TV in the vicinity of the Koongarra uranium ore field and predictable groundwater flow

    International Nuclear Information System (INIS)

    Miyakawa, Kimio; Tanaka, Yasuharu

    1996-01-01

    To contribute good understanding of geo-hydrogeological structure in and around the Koongarra uranium deposit, the borehole TV logging and the three dimensional groundwater flow analysis were conducted. The results of the borehole TV measurement showed directional trends in the schistosity represented folds which were the most characteristic structure in the site scale. This fold structure was in accord with the directional trends in fracture and fracture frequency, and the axes of the interference test drawdown. The three dimensional groundwater flow analysis was taken into account the hydraulic anisotropy which derived from the assumption that the direction normal to schistosity agree with minimum hydraulic conductivity. The result of analysis showed that directions of ground water flow agreed with drawdown axes, and the conceptual model of hydrogeological structure governed the site scale fold was verified. (author)

  10. Groundwater flow modeling focused on the Fukushima Daiichi Nuclear Power Plant Site

    International Nuclear Information System (INIS)

    Saegusa, Hiromitsu; Onoe, Hironori; Kohashi, Akio; Watanabe, Masahisa

    2015-01-01

    Fukushima Daiichi nuclear power plant of Tokyo Electric Power Company is facing contaminated water issues in the aftermath of the Great East Japan Earthquake on March 11, 2011. The amount of contaminated water is continuously increasing due to groundwater leakage into the underground part of reactor and turbine buildings. Therefore, it is important to understand the groundwater flow conditions at the site and to predict the impact of countermeasures taken for isolating groundwater from the source of the contamination, i.e. the reactor buildings. Installations, such as of land-side and sea-side impermeable walls have been planned as countermeasures. In this study, groundwater flow modeling has been performed to estimate the response of groundwater flow conditions to the countermeasures. From the modeling, groundwater recharge and discharge areas, major groundwater flow direction, inflow rate into underground part of the buildings, and changes in response to implementation of the countermeasures could be reasonably estimated. The results indicate that the countermeasures will decrease the volume of inflow into the underground part of the buildings. This means that the countermeasures will be effective in reducing the discharge volume of contaminated groundwater to ocean. (author)

  11. Influence of irrigation on the level, salinity and flow of groundwater at ...

    African Journals Online (AJOL)

    2010-03-31

    Mar 31, 2010 ... Installation of a piezometer network. • Fieldwork monitoring groundwater levels and piezometer electrical conductivity (EC) profiling. • Analysing groundwater levels and EC. • Monitoring drains on selected sites. • Profiling and testing of aquifer parameters. • Conceptual modelling to test the salt flow paths.

  12. First status report on regional ground-water flow modeling for the Paradox Basin, Utah

    International Nuclear Information System (INIS)

    Andrews, R.W.

    1984-05-01

    Regional ground-water flow within the principal hydrogeologic units of the Paradox Basin is evaluated by developing a conceptual model of the flow regime in the shallow aquifers and the deep-basin brine aquifers and testing these models using a three-dimensional, finite-difference flow code. Semiquantitative sensitivity analysis (a limited parametric study) is conducted to define the system response to changes in hydrologic properties or boundary conditions. A direct method for sensitivity analysis using an adjoint form of the flow equation is applied to the conceptualized flow regime in the Leadville limestone aquifer. All steps leading to the final results and conclusions are incorporated in this report. The available data utilized in this study is summarized. The specific conceptual models, defining the areal and vertical averaging of litho-logic units, aquifer properties, fluid properties, and hydrologic boundary conditions, are described in detail. Two models were evaluated in this study: a regional model encompassing the hydrogeologic units above and below the Paradox Formation/Hermosa Group and a refined scale model which incorporated only the post Paradox strata. The results are delineated by the simulated potentiometric surfaces and tables summarizing areal and vertical boundary fluxes, Darcy velocities at specific points, and ground-water travel paths. Results from the adjoint sensitivity analysis include importance functions and sensitivity coefficients, using heads or the average Darcy velocities to represent system response. The reported work is the first stage of an ongoing evaluation of the Gibson Dome area within the Paradox Basin as a potential repository for high-level radioactive wastes

  13. Groundwater flow through a natural fracture. Flow experiments and numerical modelling

    Energy Technology Data Exchange (ETDEWEB)

    Larsson, Erik [Chalmers Univ. of Technology, Goeteborg (Sweden). Dept of Geology

    1997-09-01

    Groundwater flow and transport play an important role not only for groundwater exploration but also in environmental engineering problems. This report considers how the hydraulic properties of fractures in crystalline rock depend on the fracture aperture geometry. Different numerical models are discussed and a FDM computer code for two- and three- dimensional flow-modelling has been developed. Different relations between the cells in the model are tested and compared with results in the literature. A laboratory experimental work has been done to carry out flow experiments and aperture measurements on the same specimen of a natural fracture. The drilled core sample had fractures parallel to the core axis and was placed inside a biaxial cell during the experiments. The water pressure gradient and the compression stress were varied during the experiments and also a tracer test was done. After the flow experiments, the aperture distribution for a certain compression was measured by injecting an epoxy resin into the fracture. The thickness of the resin layer was then studied in saw cut sections of the sample. The results from the experiments were used to validate numerical and analytical models, based on aperture distribution, for flow and transport simulations. In the disturbed zone around a drift both water and air are present in the fractures. The gas will go to the most wide part of the fracture because the capillarity and the conductivity decrease. The dependence of the effective conductivity on the variance of the conductivity and the effect of extinction of highly conductive cells has also been studied. A discussion of how gas in fractures around a drift can cause a skin effect is modelled and an example is given of what a saturation depending on the magnitude of the flow causes. 25 refs, 17 tabs, 43 figs.

  14. Stable isotope and groundwater flow dynamics of agricultural irrigation recharge into groundwater resources of the Central Valley, California

    International Nuclear Information System (INIS)

    Davisson, M.L.; Criss, R.E.

    1995-01-01

    Intensive agricultural irrigation and overdraft of groundwater in the Central Valley of California profoundly affect the regional quality and availability of shallow groundwater resources. In the natural state, the δ 18 O values of groundwater were relatively homogeneous (mostly -7.0 ± 0.5 per-thousand), reflecting local meteoric recharge that slowly (1-3m/yr) flowed toward the valley axis. Today, on the west side of the valley, the isotope distribution is dominated by high 18 O enclosures formed by recharge of evaporated irrigation waters, while the east side has bands of low 18 O groundwater indicating induced recharge from rivers draining the Sierra Nevada mountains. Changes in δ 18 O values caused by the agricultural recharge strongly correlate with elevated nitrate concentrations (5 to >100 mg/L) that form pervasive, non-point source pollutants. Small, west-side cities dependent solely on groundwater resources have experienced increases of >1.0 mg/L per year of nitrate for 10-30 years. The resultant high nitrates threaten the economical use of the groundwater for domestic purposes, and have forced some well shut-downs. Furthermore, since >80% of modern recharge is now derived from agricultural irrigation, and because modern recharge rates are ∼10 times those of the natural state, agricultural land retirement by urbanization will severely curtail the current safe-yields and promote overdraft pumping. Such overdrafting has occurred in the Sacramento metropolitan area for ∼40 years, creating cones of depression ∼25m deep. Today, groundwater withdrawal in Sacramento is approximately matched by infiltration of low 18 O water (-11.0 per-thousand) away from the Sacramento and American Rivers, which is estimated to occur at 100-300m/year from the sharp 18 O gradients in our groundwater isotope map

  15. Consideration of Typical Nuclear Power Plant Site Characteristics for Groundwater Flow

    International Nuclear Information System (INIS)

    Kim, Chan Hoi; Yee, Eric

    2014-01-01

    This is complicated by the extreme measures the plant owners have taken by pumping water into the disabled plant in order to cool the corium, making it difficult for workers to inspect the facility and mitigate radiation hazards. One of most confusing aspects of the groundwater contamination issue at the Fukushima Daiichi nuclear power plant is the flow of groundwater, with conflicting reports saying there is very little water to significant amounts of water flowing towards the plant. Initially, different media outlets, reports, and figures show anywhere from uniform flow to nearly impossible flow situations, with a general improvement in groundwater flow feasibility over time as perhaps more knowledge of the subgrade or facilities is revealed. This situation highlights the importance of groundwater models, which traditionally use averaged and macro-scale adjusted subgrade properties. These are not necessarily bad practices, but some details may be lost in the process for more local scenarios. Therefore, this paper focuses on the site conditions of a typical nuclear power plant and its influences on local groundwater flow modelling. Site-specific data from the hydrologic system investigation must be prepared and utilized to evaluate the existing groundwater conditions and to identify pathway of groundwater flow toward subsurface and plant facilities before and after nuclear power plant construction by installing monitoring wells. These investigation data, evaluation and identification provide the basis for developing an overall conceptual model of groundwater. With this conceptual model, assumption of radioactive material release, for instance, the liquid radioactive waste from a ruptured tank in the compound building through cracks in the foundation wall enter the groundwater system, can be evaluated

  16. RCRA groundwater data analysis protocol for the Hanford Site, Washington

    International Nuclear Information System (INIS)

    Chou, C.J.; Jackson, R.L.

    1992-04-01

    The Resource Conservation and Recovery Act of 1976 (RCRA) groundwater monitoring program currently involves site-specific monitoring of 20 facilities on the Hanford Site in southeastern Washington. The RCRA groundwater monitoring program has collected abundant data on groundwater quality. These data are used to assess the impact of a facility on groundwater quality or whether remediation efforts under RCRA corrective action programs are effective. Both evaluations rely on statistical analysis of groundwater monitoring data. The need for information on groundwater quality by regulators and environmental managers makes statistical analysis of monitoring data an important part of RCRA groundwater monitoring programs. The complexity of groundwater monitoring programs and variabilities (spatial, temporal, and analytical) exhibited in groundwater quality variables indicate the need for a data analysis protocol to guide statistical analysis. A data analysis protocol was developed from the perspective of addressing regulatory requirements, data quality, and management information needs. This data analysis protocol contains four elements: data handling methods; graphical evaluation techniques; statistical tests for trend, central tendency, and excursion analysis; and reporting procedures for presenting results to users

  17. Arrangement of disposal holes according to the features of groundwater flow

    Energy Technology Data Exchange (ETDEWEB)

    Ko, Nak Youl; Baik, Min Hoon [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2016-12-15

    Based on the results of groundwater flow system modeling for a hypothetical deep geological repository site, quantitative and spatial distributions of groundwater flow rates at the positions of deposition holes, groundwater travel length and time from the positions to the surface environment were analyzed and used to suggest a method for determining locations of deposition holes. The hydraulic head values at the depth of the deposition holes and a particle tracking method were used to calculate the groundwater flow rates and groundwater travel length and time, respectively. From the results, an approach to designing a layout of deposition holes was suggested by selecting relatively favorable positions for maintaining performance of the disposal facility and screening some positions of deposition holes that did not comply with specific constraints for the groundwater flow rates, travel length and time. In addition, a method for determining a geometrical direction for extension of the disposal facility was discussed. Designing the layout of deposition holes with the information of groundwater flow at the disposal depth can contribute to secure performance and safety of the disposal facility.

  18. Investigation of groundwater flow potential in Makurdi, North Central ...

    African Journals Online (AJOL)

    hp

    water (Akinbinu, 2015). Surface and groundwater resources are abundant in Nigeria. The water resources master plan for Nigeria which was prepared by the Japan. International Co-operation Agency (JICA) in 2006 indicates an estimated surface water resource of about .67 and groundwater storage of about. (Oteze, 2006) ...

  19. Groundwater flow modelling of Yamuna–Krishni interstream, a part ...

    Indian Academy of Sciences (India)

    Groundwater is a major source of water for agricultural and domestic requirements in western Uttar Pradesh.Due to increasing agricultural requirements the abstraction of groundwater has increased manifold in the last two-to-three decades.The quaternary alluvium hosts the aquifer in the region.The study area forms a part ...

  20. Comparing groundwater recharge and base flow in the Bukmoongol ...

    Indian Academy of Sciences (India)

    Groundwater recharge and base flow using different investigated methods are simulated in the 15-ha Bukmoongol small-forested watershed located at the southern part of Korea.The WHAT system, PART,RORA,PULSE,BFI,and RAP software are used to estimate groundwater recharge or base flow and base flow index from ...

  1. A Finite Layer Formulation for Groundwater Flow to Horizontal Wells.

    Science.gov (United States)

    Xu, Jin; Wang, Xudong

    2016-09-01

    A finite layer approach for the general problem of three-dimensional (3D) flow to horizontal wells in multilayered aquifer systems is presented, in which the unconfined flow can be taken into account. The flow is approximated by an integration of the standard finite element method in vertical direction and the analytical techniques in the other spatial directions. Because only the vertical discretization is involved, the horizontal wells can be completely contained in one specific nodal plane without discretization. Moreover, due to the analytical eigenfunctions introduced in the formulation, the weighted residual equations can be decoupled, and the formulas for the global matrices and flow vector corresponding to horizontal wells can be obtained explicitly. Consequently, the bandwidth of the global matrices and computational cost rising from 3D analysis can be significantly reduced. Two comparisons to the existing solutions are made to verify the validity of the formulation, including transient flow to horizontal wells in confined and unconfined aquifers. Furthermore, an additional numerical application to horizontal wells in three-layered systems is presented to demonstrate the applicability of the present method in modeling flow in more complex aquifer systems. © 2016, National Ground Water Association.

  2. Groundwater flow, quality (2007-10), and mixing in the Wind Cave National Park area, South Dakota

    Science.gov (United States)

    Long, Andrew J.; Ohms, Marc J.; McKaskey, Jonathan D.R.G.

    2012-01-01

    A study of groundwater flow, quality, and mixing in relation to Wind Cave National Park in western South Dakota was conducted during 2007-11 by the U.S. Geological Survey in cooperation with the National Park Service because of water-quality concerns and to determine possible sources of groundwater contamination in the Wind Cave National Park area. A large area surrounding Wind Cave National Park was included in this study because to understand groundwater in the park, a general understanding of groundwater in the surrounding southern Black Hills is necessary. Three aquifers are of particular importance for this purpose: the Minnelusa, Madison, and Precambrian aquifers. Multivariate methods applied to hydrochemical data, consisting of principal component analysis (PCA), cluster analysis, and an end-member mixing model, were applied to characterize groundwater flow and mixing. This provided a way to assess characteristics important for groundwater quality, including the differentiation of hydrogeologic domains within the study area, sources of groundwater to these domains, and groundwater mixing within these domains. Groundwater and surface-water samples collected for this study were analyzed for common ions (calcium, magnesium, sodium, bicarbonate, chloride, silica, and sulfate), arsenic, stable isotopes of oxygen and hydrogen, specific conductance, and pH. These 12 variables were used in all multivariate methods. A total of 100 samples were collected from 60 sites from 2007 to 2010 and included stream sinks, cave drip, cave water bodies, springs, and wells. In previous approaches that combined PCA with end-member mixing, extreme-value samples identified by PCA typically were assumed to represent end members. In this study, end members were not assumed to have been sampled but rather were estimated and constrained by prior hydrologic knowledge. Also, the end-member mixing model was quantified in relation to hydrogeologic domains, which focuses model results on

  3. The state of the art of groundwater flow modeling for safety assessment of a radwaste repository

    International Nuclear Information System (INIS)

    Ji, Sung Hoon; Koh, Yong Kwon; Kim, Kyung Su; Kim, Geon Young; Park, Kyung Woo; Ryu, Ji Hoon

    2010-02-01

    In this report, we investigated the general processes to model the groundwater flow system in a fractured aquifer and the mathematical approaches to simulate it. Then, we reviewed several modeling cases of nuclear advanced nations (e.g. Switzerland, U.S., Canada, and Sweden) for simulating the groundwater flow system for safety assessment of their real or hypothetical radwaste repository. From the reviews, we introduced some requisite research items

  4. Simulation of the effects of rainfall and groundwater use on historical lake water levels, groundwater levels, and spring flows in central Florida

    Science.gov (United States)

    O'Reilly, Andrew M.; Roehl, Edwin A.; Conrads, Paul; Daamen, Ruby C.; Petkewich, Matthew D.

    2014-01-01

    The urbanization of central Florida has progressed substantially in recent decades, and the total population in Lake, Orange, Osceola, Polk, and Seminole Counties more than quadrupled from 1960 to 2010. The Floridan aquifer system is the primary source of water for potable, industrial, and agricultural purposes in central Florida. Despite increases in groundwater withdrawals to meet the demand of population growth, recharge derived by infiltration of rainfall in the well-drained karst terrain of central Florida is the largest component of the long-term water balance of the Floridan aquifer system. To complement existing physics-based groundwater flow models, artificial neural networks and other data-mining techniques were used to simulate historical lake water level, groundwater level, and spring flow at sites throughout the area. Historical data were examined using descriptive statistics, cluster analysis, and other exploratory analysis techniques to assess their suitability for more intensive data-mining analysis. Linear trend analyses of meteorological data collected by the National Oceanic and Atmospheric Administration at 21 sites indicate 67 percent of sites exhibited upward trends in air temperature over at least a 45-year period of record, whereas 76 percent exhibited downward trends in rainfall over at least a 95-year period of record. Likewise, linear trend analyses of hydrologic response data, which have varied periods of record ranging in length from 10 to 79 years, indicate that water levels in lakes (307 sites) were about evenly split between upward and downward trends, whereas water levels in 69 percent of wells (out of 455 sites) and flows in 68 percent of springs (out of 19 sites) exhibited downward trends. Total groundwater use in the study area increased from about 250 million gallons per day (Mgal/d) in 1958 to about 590 Mgal/d in 1980 and remained relatively stable from 1981 to 2008, with a minimum of 559 Mgal/d in 1994 and a maximum of 773

  5. Groundwater-flow modeling in the Yucatan karstic aquifer, Mexico

    Science.gov (United States)

    González-Herrera, Roger; Sánchez-y-Pinto, Ismael; Gamboa-Vargas, José

    2002-09-01

    The current conceptual model of the unconfined karstic aquifer in the Yucatan Peninsula, Mexico, is that a fresh-water lens floats above denser saline water that penetrates more than 40 km inland. The transmissivity of the aquifer is very high so the hydraulic gradient is very low, ranging from 7-10 mm/km through most of the northern part of the peninsula. The computer modeling program AQUIFER was used to investigate the regional groundwater flow in the aquifer. The karstified zone was modeled using the assumption that it acts hydraulically similar to a granular, porous medium. As part of the calibration, the following hypotheses were tested: (1) karstic features play an important role in the groundwater-flow system; (2) a ring or belt of sinkholes in the area is a manifestation of a zone of high transmissivity that facilitates the channeling of groundwater toward the Gulf of Mexico; and (3) the geologic features in the southern part of Yucatan influence the groundwater-flow system. The model shows that the Sierrita de Ticul fault, in the southwestern part of the study area, acts as a flow barrier and head values decline toward the northeast. The modeling also shows that the regional flow-system dynamics have not been altered despite the large number of pumping wells because the volume of water pumped is small compared with the volume of recharge, and the well-developed karst system of the region has a very high hydraulic conductivity. Résumé. Le modèle conceptuel classique de l'aquifère karstique libre de la péninsule du Yucatan (Mexique) consiste en une lentille d'eau douce flottant sur une eau salée plus dense qui pénètre à plus de 40 km à l'intérieur des terres. La transmissivité de l'aquifère est très élevée, en sorte que le gradient hydraulique est très faible, compris entre 7 et 10 mm/km dans la plus grande partie du nord de la péninsule. Le modèle AQUIFER a été utilisé pour explorer les écoulements souterrains régionaux dans cet

  6. Modeling groundwater flow at the chemical plant area of the Weldon Spring Site

    International Nuclear Information System (INIS)

    Durham, L.A.

    1992-10-01

    Groundwater flow in the shallow unconfined aquifer at the chemical plant area of the Weldon Spring site, St. Charles County, Missouri, was modeled with the Coupled Fluid, Energy, and Solute Transport (CFEST) groundwater flow and contaminant transport computer code. The modeling was performed in support of a hydrogeological characterization effort that is part of the remedial investigation/feasibility study-environmental impact statement process being carried out by the US Department of Energy at the site. This report presents the results of model development and calibration. In the calibration procedure, the range of field-measured hydrogeological parameters was tested to obtain the best match between model-predicted and measured groundwater elevations. After calibration, the model was used to evaluate whether the presence of an on-site disposal cell would impact the ability to remediate contaminated groundwater beneath the cell. The results of the numerical modeling, which were based on an evaluation of steady-state groundwater flow velocity plots, indicated that groundwater would flow beneath the disposal cell along natural gradients. The presence of a disposal cell would not significantly affect remediation capability for groundwater contamination

  7. Investigation of the effect of groundwater flow in a complex hydraulic situation

    Science.gov (United States)

    Simon, Szilvia; Balogh, Viktor; Tóth, Ádám; Mádl-Szönyi, Judit

    2016-04-01

    Groundwater flow systems are the subsurface elements of the hydrologic cycle, thus they have an important effect on surface water bodies and surface water-groundwater interaction processes. Moreover, groundwater flow systems are not simple, different driving forces govern and form different regimes with different behaviour. Their effects on surface systems differs, respectively. Based on this consideration, the characterization of the subsurface flow regimes and their operating mechanisms are crucial for the understanding of hydrological problems and situations at the surface. The Great Hungarian Plain can be handled as a natural laboratory, where several geological mechanisms act as groundwater driving forces. As a result, two main flow regimes, a gravity-driven, unconfined, and a confined, overpressured system could be separated (Tóth and Almási, 2001). The recharge and water budget of the systems, their spatial distribution, and their surface discharge features influence the possibilities of water withdrawal from them, their effect on the surface water bodies, vegetation, soil mechanisms and salinization etc. Numerical modelling with COMSOL Multiphysics was carried out for the Duna-Tisza Interfluve area of the Great Hungarian Plain, to characterize the two main flow regimes at three different scales. The aim of the study was to understand the flow distribution and their surface discharge character in quantitative way. The simulation was based on the understanding of the systems' operation from preproduction hydraulic head and pressure data analysis by Mádl-Szönyi and Tóth (2009). These data could serve as basis for the validation of the model. The results were interpreted and discussed focusing on the flow systems' possible influence on the surface salinization, lake water - groundwater interactions, inland water problems, land-use planning. It could be revealed that overpressured system is concentrated in the deep basin and the overpressure maintains

  8. Numerical groundwater flow calculations at the Finnsjoen site

    International Nuclear Information System (INIS)

    Lindbom, B.; Boghammar, A.; Lindberg, H.; Bjelkaas, J.

    1991-02-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) has initiated a research project called SKB 91, which is related to performance assessment of repositories for high level waste from nuclear power plants. Specifically the Finnsjoen site is of concern. As part of this research project, the report describes groundwater flow calculations at the Finnsjoen site, located in northern Uppland, approximately 150 km north of Stockholm. The calculations have been performed with the finite element method applying the porous media approach. The project comprises three steps, the first of which is concerned with the presence of salt below a hydraulically significant structure. This step was modelled in two dimensions in a semi-generic fashion, while the two following steps comprised three-dimensional modelling of the site at a semi-regional and a local scale. The semi-regional model covered approximately 43 square km while the area of the local model was roughly 6.6 square km. The semi-regional model included well expressed regional fracture zones that were explicitly modelled in deterministic manner. The modelling was performed with the finite element code NAMMU, used together with the program-package HYPAC. The latter was used for pre- and postprocessing purposes. The modelling was performed with 8-noded brick elements for the three-dimensional calculations, and the two-dimensional model involved the use of 8-noded rectangular elements. The present report is a revised version of a report previously published as a working report. The difference between the present report and the previous one, is that the present report describes the conclusions more site-specifically, the presentation of a number of the cases tackled has been pruned down, some editorial effort has been put into having the volume of the report reduced, and finally the summary has been edited and cut down. (authors)

  9. Groundwater flow modelling of periods with periglacial and glacial climate conditions - Forsmark

    Energy Technology Data Exchange (ETDEWEB)

    Vidstrand, Patrik (TerraSolve AB, Floda (Sweden)); Follin, Sven (SF GeoLogic AB, Taeby (Sweden)); Zugec, Nada (Bergab, Stockholm (Sweden))

    2010-12-15

    As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The groundwater flow modelling study reported here comprises a coupled thermal-hydraulic-chemical (T-H-C) analysis of periods with periglacial and glacial climate conditions. Hydraulic-mechanical (H-M) issues are also handled but no coupled flow modelling is done. The objective of the report is to provide bounding hydrogeological estimates at different stages during glaciation and deglaciation of a glacial cycle for subsequent use in safety assessment applications within SKB's project SR-Site. Three cases with different climate conditions are analysed here: (i) Temperate case, (ii) Glacial case without permafrost, and (iii) Glacial case with permafrost. The glacial periods are transient and encompass approximately 19,000 years. The simulation results comprise residual fluid pressures, Darcy fluxes, and water salinities, as well as advective transport performance measures obtained by particle tracking such as flow path lengths, travel times and flow-related transport resistances. The modelling is accompanied by a sensitivity study that addresses the impact of the following matters: the direction of the ice sheet advance, the speed of the ice sheet margin, the bedrock hydraulic and transport properties, the temperature at the ice-subsurface interface close to the ice sheet margin, and the initial hydrochemical conditions.

  10. Groundwater flow modelling of periods with periglacial and glacial climate conditions - Forsmark

    International Nuclear Information System (INIS)

    Vidstrand, Patrik; Follin, Sven; Zugec, Nada

    2010-12-01

    As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The groundwater flow modelling study reported here comprises a coupled thermal-hydraulic-chemical (T-H-C) analysis of periods with periglacial and glacial climate conditions. Hydraulic-mechanical (H-M) issues are also handled but no coupled flow modelling is done. The objective of the report is to provide bounding hydrogeological estimates at different stages during glaciation and deglaciation of a glacial cycle for subsequent use in safety assessment applications within SKB's project SR-Site. Three cases with different climate conditions are analysed here: (i) Temperate case, (ii) Glacial case without permafrost, and (iii) Glacial case with permafrost. The glacial periods are transient and encompass approximately 19,000 years. The simulation results comprise residual fluid pressures, Darcy fluxes, and water salinities, as well as advective transport performance measures obtained by particle tracking such as flow path lengths, travel times and flow-related transport resistances. The modelling is accompanied by a sensitivity study that addresses the impact of the following matters: the direction of the ice sheet advance, the speed of the ice sheet margin, the bedrock hydraulic and transport properties, the temperature at the ice-subsurface interface close to the ice sheet margin, and the initial hydrochemical conditions

  11. Analysis of hydrogeological flow responses in Olkiluoto

    International Nuclear Information System (INIS)

    Ahokas, H.; Rouhiainen, P.; Komulainen, J.; Poellaenen, J.

    2014-04-01

    As part of the programme for the final disposal of spent nuclear fuel, an analysis of the flow responses caused by ONKALO leakages or other activities on the site has been compiled. Leakages into ONKALO or other activities, such as pumping in connection with groundwater sampling, cause changes in flow conditions in adjacent drillholes. Flows in open drillholes have been measured with the PFL-tool (PFL-DIFF), several times in some holes, as part of Olkiluoto Monitoring Programme (OMO) or in conjunction of interference test campaigns carried out in Olkiluoto. The main objective of the study is to analyse differences detected between flow measurements without pumping. PFL-measurements were started in 1997 and all the holes have been measured. In total, measurements have been repeated in 32 holes, which enables a study of possible changes. The development of interpretation methods to detect and quantify flow changes was an important part of this work. The determination of the exact flow response is a challenging task. Changes are caused in flow also by seasonal effects, which complicate an unambiguous analysis of the observed parameters. Overlapping activities (sinks) behind flow changes make the analysis difficult. In addition, the role of other open holes close to the observation hole can be significant. They may cause flow responses, which would not have been detected without their existence. Nevertheless, unambiguous flow responses caused by the pumping of a drillhole or leaking tunnels have been detected in scales from ca. 10 m to over 1 km. (orig.)

  12. A regional groundwater-flow model for sustainable groundwater-resource management in the south Asian megacity of Dhaka, Bangladesh

    Science.gov (United States)

    Islam, Md Bayzidul; Firoz, A. B. M.; Foglia, Laura; Marandi, Andres; Khan, Abidur Rahman; Schüth, Christoph; Ribbe, Lars

    2017-05-01

    The water resources that supply most of the megacities in the world are under increased pressure because of land transformation, population growth, rapid urbanization, and climate-change impacts. Dhaka, in Bangladesh, is one of the largest of 22 growing megacities in the world, and it depends on mainly groundwater for all kinds of water needs. The regional groundwater-flow model MODFLOW-2005 was used to simulate the interaction between aquifers and rivers in steady-state and transient conditions during the period 1981-2013, to assess the impact of development and climate change on the regional groundwater resources. Detailed hydro-stratigraphic units are described according to 150 lithology logs, and a three-dimensional model of the upper 400 m of the Greater Dhaka area was constructed. The results explain how the total abstraction (2.9 million m3/d) in the Dhaka megacity, which has caused regional cones of depression, is balanced by recharge and induced river leakage. The simulated outcome shows the general trend of groundwater flow in the sedimentary Holocene aquifers under a variety of hydrogeological conditions, which will assist in the future development of a rational and sustainable management approach.

  13. Effects of groundwater-flow paths on nitrate concentrations across two riparian forest corridors

    Science.gov (United States)

    Speiran, Gary K.

    2010-01-01

    Groundwater levels, apparent age, and chemistry from field sites and groundwater-flow modeling of hypothetical aquifers collectively indicate that groundwater-flow paths contribute to differences in nitrate concentrations across riparian corridors. At sites in Virginia (one coastal and one Piedmont), lowland forested wetlands separate upland fields from nearby surface waters (an estuary and a stream). At the coastal site, nitrate concentrations near the water table decreased from more than 10 mg/L beneath fields to 2 mg/L beneath a riparian forest buffer because recharge through the buffer forced water with concentrations greater than 5 mg/L to flow deeper beneath the buffer. Diurnal changes in groundwater levels up to 0.25 meters at the coastal site reflect flow from the water table into unsaturated soil where roots remove water and nitrate dissolved in it. Decreases in aquifer thickness caused by declines in the water table and decreases in horizontal hydraulic gradients from the uplands to the wetlands indicate that more than 95% of the groundwater discharged to the wetlands. Such discharge through organic soil can reduce nitrate concentrations by denitrification. Model simulations are consistent with field results, showing downward flow approaching toe slopes and surface waters to which groundwater discharges. These effects show the importance of buffer placement over use of fixed-width, streamside buffers to control nitrate concentrations.

  14. Simulated groundwater flow paths, travel time, and advective transport of nitrogen in the Kirkwood-Cohansey aquifer system, Barnegat Bay–Little Egg Harbor Watershed, New Jersey

    Science.gov (United States)

    Voronin, Lois M.; Cauller, Stephen J.

    2017-07-31

    Elevated concentrations of nitrogen in groundwater that discharges to surface-water bodies can degrade surface-water quality and habitats in the New Jersey Coastal Plain. An analysis of groundwater flow in the Kirkwood-Cohansey aquifer system and deeper confined aquifers that underlie the Barnegat Bay–Little Egg Harbor (BB-LEH) watershed and estuary was conducted by using groundwater-flow simulation, in conjunction with a particle-tracking routine, to provide estimates of groundwater flow paths and travel times to streams and the BB-LEH estuary.Water-quality data from the Ambient Groundwater Quality Monitoring Network, a long-term monitoring network of wells distributed throughout New Jersey, were used to estimate the initial nitrogen concentration in recharge for five different land-use classes—agricultural cropland or pasture, agricultural orchard or vineyard, urban non-residential, urban residential, and undeveloped. Land use at the point of recharge within the watershed was determined using a geographic information system (GIS). Flow path starting locations were plotted on land-use maps for 1930, 1973, 1986, 1997, and 2002. Information on the land use at the time and location of recharge, time of travel to the discharge location, and the point of discharge were determined for each simulated flow path. Particle-tracking analysis provided the link from the point of recharge, along the particle flow path, to the point of discharge, and the particle travel time. The travel time of each simulated particle established the recharge year. Land use during the year of recharge was used to define the nitrogen concentration associated with each flow path. The recharge-weighted average nitrogen concentration for all flow paths that discharge to the Toms River upstream from streamflow-gaging station 01408500 or to the BB-LEH estuary was calculated.Groundwater input into the Barnegat Bay–Little Egg Harbor estuary from two main sources— indirect discharge from base

  15. Hydrochemistry of the groundwater flow systems in the Harwell region

    International Nuclear Information System (INIS)

    Alexander, J.

    1984-12-01

    A comprehensive range of geochemical and isotopic parameters were analysed in the groundwater samples taken from the high permeability formations in the Harwell region. These analyses were undertaken as part of a hydro-chemical validation of groundwater circulation patterns derived from potentiometric data. Hydro-chemical investigations were concentrated upon the Corallian and Great Oolite formations since these respectively overlie and underlie the Oxford Clay. (author)

  16. Groundwater origin and flow along selected transects in Ethiopian rift volcanic aquifers

    Science.gov (United States)

    Kebede, Seifu; Travi, Yves; Asrat, Asfawossen; Alemayehu, Tamiru; Ayenew, Tenalem; Tessema, Zenaw

    2008-02-01

    The disruption of lithologies by cross-cutting faults and the variability in volcanic structures make the hydrogeology of the rifted volcanic terrain in Ethiopia very complex. Along two transects, selected due to their hydrogeologic characteristics, groundwater flow, depth of circulation and geochemical evolution have been conceptualized. The groundwater flow continuity between the high rainfall plateau bounding the rift and the rift valley aquifers depends principally on the nature of the bounding faults. Up to 50% of recharge to the rift aquifers comes from the plateau as groundwater inflow where the rift is cross cut by transverse fault zones. Recharge from the mountains is found to be insignificant where the rift is bounded by marginal grabens; channel loss and local precipitation are the principal sources of recharge to the rift aquifers in such cases. At a regional scale, there is a clear zonation in the geochemical compositions of groundwaters, the result of aquifer matrix composition differences. The environmental isotope results show that the majority of the aquifers contain modern groundwaters. In a few localities, particularly in thermal groundwaters representing deeper circulation, palaeo-groundwaters have been identified. Deeper groundwaters in the rift floor have a uniform 14C age ranging between 2,300 and 3,000 years.

  17. Site-scale groundwater flow modelling of Ceberg

    Energy Technology Data Exchange (ETDEWEB)

    Walker, D. [Duke Engineering and Services (United States); Gylling, B. [Kemakta Konsult AB, Stockholm (Sweden)

    1999-06-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) SR 97 study is a comprehensive performance assessment illustrating the results for three hypothetical repositories in Sweden. In support of SR 97, this study examines the hydrogeologic modelling of the hypothetical site called Ceberg, which adopts input parameters from the SKB study site near Gideaa, in northern Sweden. This study uses a nested modelling approach, with a deterministic regional model providing boundary conditions to a site-scale stochastic continuum model. The model is run in Monte Carlo fashion to propagate the variability of the hydraulic conductivity to the advective travel paths from representative canister locations. A series of variant cases addresses uncertainties in the inference of parameters and the model of conductive fracturezones. The study uses HYDRASTAR, the SKB stochastic continuum (SC) groundwater modelling program, to compute the heads, Darcy velocities at each representative canister position, and the advective travel times and paths through the geosphere. The volumetric flow balance between the regional and site-scale models suggests that the nested modelling and associated upscaling of hydraulic conductivities preserve mass balance only in a general sense. In contrast, a comparison of the base and deterministic (Variant 4) cases indicates that the upscaling is self-consistent with respect to median travel time and median canister flux. These suggest that the upscaling of hydraulic conductivity is approximately self-consistent but the nested modelling could be improved. The Base Case yields the following results for a flow porosity of {epsilon}{sub f} 10{sup -4} and a flow-wetted surface area of a{sub r} = 0.1 m{sup 2}/(m{sup 3} rock): The median travel time is 1720 years. The median canister flux is 3.27x10{sup -5} m/year. The median F-ratio is 1.72x10{sup 6} years/m. The base case and the deterministic variant suggest that the variability of the travel times within

  18. Site-scale groundwater flow modelling of Ceberg

    International Nuclear Information System (INIS)

    Walker, D.; Gylling, B.

    1999-06-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) SR 97 study is a comprehensive performance assessment illustrating the results for three hypothetical repositories in Sweden. In support of SR 97, this study examines the hydrogeologic modelling of the hypothetical site called Ceberg, which adopts input parameters from the SKB study site near Gideaa, in northern Sweden. This study uses a nested modelling approach, with a deterministic regional model providing boundary conditions to a site-scale stochastic continuum model. The model is run in Monte Carlo fashion to propagate the variability of the hydraulic conductivity to the advective travel paths from representative canister locations. A series of variant cases addresses uncertainties in the inference of parameters and the model of conductive fracture zones. The study uses HYDRASTAR, the SKB stochastic continuum (SC) groundwater modelling program, to compute the heads, Darcy velocities at each representative canister position, and the advective travel times and paths through the geosphere. The volumetric flow balance between the regional and site-scale models suggests that the nested modelling and associated upscaling of hydraulic conductivities preserve mass balance only in a general sense. In contrast, a comparison of the base and deterministic (Variant 4) cases indicates that the upscaling is self-consistent with respect to median travel time and median canister flux. These suggest that the upscaling of hydraulic conductivity is approximately self-consistent but the nested modelling could be improved. The Base Case yields the following results for a flow porosity of ε f 10 -4 and a flow-wetted surface area of a r = 0.1 m 2 /(m 3 rock): The median travel time is 1720 years. The median canister flux is 3.27x10 -5 m/year. The median F-ratio is 1.72x10 6 years/m. The base case and the deterministic variant suggest that the variability of the travel times within individual realisations is due to the

  19. Estimation of regional-scale groundwater flow properties in the Bengal Basin of India and Bangladesh

    Science.gov (United States)

    Michael, H.A.; Voss, C.I.

    2009-01-01

    Quantitative evaluation of management strategies for long-term supply of safe groundwater for drinking from the Bengal Basin aquifer (India and Bangladesh) requires estimation of the large-scale hydrogeologic properties that control flow. The Basin consists of a stratified, heterogeneous sequence of sediments with aquitards that may separate aquifers locally, but evidence does not support existence of regional confining units. Considered at a large scale, the Basin may be aptly described as a single aquifer with higher horizontal than vertical hydraulic conductivity. Though data are sparse, estimation of regional-scale aquifer properties is possible from three existing data types: hydraulic heads, 14C concentrations, and driller logs. Estimation is carried out with inverse groundwater modeling using measured heads, by model calibration using estimated water ages based on 14C, and by statistical analysis of driller logs. Similar estimates of hydraulic conductivities result from all three data types; a resulting typical value of vertical anisotropy (ratio of horizontal to vertical conductivity) is 104. The vertical anisotropy estimate is supported by simulation of flow through geostatistical fields consistent with driller log data. The high estimated value of vertical anisotropy in hydraulic conductivity indicates that even disconnected aquitards, if numerous, can strongly control the equivalent hydraulic parameters of an aquifer system. ?? US Government 2009.

  20. Influence of groundwater flow on the estimation of subsurface thermal parameters

    Science.gov (United States)

    Verdoya, Massimo; Chiozzi, Paolo

    2018-01-01

    We investigated the influence of groundwater flow on the thermal tests performed in borehole heat exchangers to infer the underground thermal properties. Temperature-time signals were simulated with a moving line source (MLS) model under different hypotheses of Darcy velocity. Periodic and random noise was included in the synthetic data obtained with this model in order to mimic high-frequency disturbances caused by several possible sources (e.g. equipment instability and changes in environmental conditions during the experiment) that often occur in real signals. The subsurface thermal conductivity, the Darcy velocity and the borehole thermal resistance were inferred by minimising the root-mean-square error between the synthetic dataset and the model. The calculated thermal and hydraulic parameters were consistent with the "a priori" values. The optimisation procedure results were then tested with the infinite line source (ILS) model. For a Darcy velocity exceeding 10-7 m s-1, ILS largely overestimates thermal conductivity. The approach relying on the MLS model was finally tested with real temperature-time data and produced reliable estimates of thermal conductivity, Darcy velocity and borehole thermal resistance. The inferred groundwater flow was cross checked by means of an independent method based on the analysis of temperature-depth logs recorded under thermal equilibrium conditions. Such a test validates the Darcy velocity inferred with the MLS approach.

  1. Hydrogeology and simulation of ground-water flow at Arnold Air Force Base, Coffee and Franklin counties, Tennessee

    Science.gov (United States)

    Haugh, C.J.; Mahoney, E.N.

    1994-01-01

    The U.S. Air Force at Arnold Air Force Base (AAFB), in Coffee and Franklin Counties, Tennessee, is investigating ground-water contamination in selected areas of the base. This report documents the results of a comprehensive investigation of the regional hydrogeology of the AAFB area. Three aquifers within the Highland Rim aquifer system, the shallow aquifer, the Manchester aquifer, and the Fort Payne aquifer, have been identified in the study area. Of these, the Manchester aquifer is the primary source of water for domestic use. Drilling and water- quality data indicate that the Chattanooga Shale is an effective confining unit, isolating the Highland Rim aquifer system from the deeper, upper Central Basin aquifer system. A regional ground-water divide, approximately coinciding with the Duck River-Elk River drainage divide, underlies AAFB and runs from southwest to northeast. The general direction of most ground-water flow is to the north- west or to the northwest or to the southeast from the divide towards tributary streams that drain the area. Recharge estimates range from 4 to 11 inches per year. Digital computer modeling was used to simulate and provide a better understanding of the ground-water flow system. The model indicates that most of the ground-water flow occurs in the shallow and Manchester aquifers. The model was most sensitive to increases in hydraulic conductivity and changes in recharge rates. Particle-tracking analysis from selected sites of ground-water contamination indicates a potential for contami- nants to be transported beyond the boundary of AAFB.

  2. Documentation for the MODFLOW 6 Groundwater Flow Model

    Science.gov (United States)

    Langevin, Christian D.; Hughes, Joseph D.; Banta, Edward R.; Niswonger, Richard G.; Panday, Sorab; Provost, Alden M.

    2017-08-10

    This report documents the Groundwater Flow (GWF) Model for a new version of MODFLOW called MODFLOW 6. The GWF Model for MODFLOW 6 is based on a generalized control-volume finite-difference approach in which a cell can be hydraulically connected to any number of surrounding cells. Users can define the model grid using one of three discretization packages, including (1) a structured discretization package for defining regular MODFLOW grids consisting of layers, rows, and columns, (2) a discretization by ver­tices package for defining layered unstructured grids consisting of layers and cells, and (3) a general unstruc­tured discretization package for defining flexible grids comprised of cells and their connection properties. For layered grids, a new capability is available for removing thin cells and vertically connecting cells overlying and underlying the thin cells. For complex problems involving water-table conditions, an optional Newton-Raphson formulation, based on the formulations in MODFLOW-NWT and MODFLOW-USG, can be acti­vated. Use of the Newton-Raphson formulation will often improve model convergence and allow solutions to be obtained for difficult problems that cannot be solved using the traditional wetting and drying approach. The GWF Model is divided into “packages,” as was done in previous MODFLOW versions. A package is the part of the model that deals with a single aspect of simulation. Packages included with the GWF Model include those related to internal calculations of groundwater flow (discretization, initial conditions, hydraulic conduc­tance, and storage), stress packages (constant heads, wells, recharge, rivers, general head boundaries, drains, and evapotranspiration), and advanced stress packages (streamflow routing, lakes, multi-aquifer wells, and unsaturated zone flow). An additional package is also available for moving water available in one package into the individual features of the advanced stress packages. The GWF Model

  3. Simulation of regional groundwater flow regarding different hydrogeological characterizations: the case of Naegelstedt catchment

    Science.gov (United States)

    Jing, Miao; Fischer, Thomas; Walther, Marc; Heße, Falk; Kolditz, Olaf; Attinger, Sabine

    2017-04-01

    We present the numerical analysis of a 3-D regional groundwater model for the Naegelstedt catchment in central Germany. The hydrogeological system is reproduced according to sparsely distributed boreholes data. The numerical analysis is carried out using the scientific software OpenGeoSys. Three alternative representations of hydrogeological zonation were systematically explored to understand their impact on groundwater travel times and paths. For each of these representations, the groundwater model was calibrated against groundwater water levels. The result shows the incorporation of gravel zone produces a better fit to the observations. Furthermore, upscaling of bore-hole scale parameter to field scale parameter is critical to model performance. Travel times calculated for all scenarios had a plausible order of magnitude. We concluded that data commonly used in groundwater modeling such as water tables and apparent groundwater ages may be insufficient to reliably estimate hydrogeological parameters.

  4. Flow Analysis Software Toolkit

    Science.gov (United States)

    Watson, Velvin; Castagnera, Karen; Plessel, Todd; Merritt, Fergus; Kelaita, Paul; West, John; Sandstrom, Tim; Clucas, Jean; Globus, AL; Bancroft, Gordon; hide

    1993-01-01

    Flow Analysis Software Toolkit (FAST) computer program provides software environment facilitating visualization of data. Collection of separate programs (modules) running simultaneously and helps user to examine results of numerical and experimental simulations. Intended for graphical depiction of computed flows, also assists in analysis of other types of data. Combines capabilities of such programs as PLOT3D, RIP, SURF, and GAS into one software environment with modules sharing data. All modules have consistent, highly interactive graphical user interface. Modular construction makes it flexible and extensible. Environment custom-configured, and new modules developed and added as needed. Written in ANSI compliant FORTRAN 77 and C language.

  5. Approaches to hazard-oriented groundwater management based on multivariate analysis of groundwater quality

    OpenAIRE

    Page, Rebecca Mary

    2011-01-01

    Drinking water extracted near rivers in alluvial aquifers is subject to potential microbial contamination due to rapidly infiltrating river water during high discharge events. The heterogeneity of river-groundwater interaction and hydrogeological characteristics of the aquifer renders a complex pattern of groundwater quality. The quality of the extracted drinking water can be managed using decision support and HACCP (Hazard Analysis and Critical Control Point) systems, but the detection of po...

  6. Complexity in the validation of ground-water travel time in fractured flow and transport systems

    International Nuclear Information System (INIS)

    Davies, P.B.; Hunter, R.L.; Pickens, J.F.

    1991-01-01

    Ground-water travel time is a widely used concept in site assessment for radioactive waste disposal. While ground-water travel time was originally conceived to provide a simple performance measure for evaluating repository sites, its definition in many flow and transport environments is ambiguous. The U.S. Department of Energy siting guidelines (10 CFR 960) define ground-water travel time as the time required for a unit volume of water to travel between two locations, calculated by dividing travel-path length by the quotient of average ground-water flux and effective porosity. Defining a meaningful effective porosity in a fractured porous material is a significant problem. Although the Waste Isolation Pilot Plant (WIPP) is not subject to specific requirements for ground-water travel time, travel times have been computed under a variety of model assumptions. Recently completed model analyses for WIPP illustrate the difficulties in applying a ground-water travel-time performance measure to flow and transport in fractured, fully saturated flow systems. Computer code used: SWIFT II (flow and transport code). 4 figs., 12 refs

  7. Hydrogeochemical analysis and evaluation of groundwater quality ...

    Indian Academy of Sciences (India)

    ical parameters of groundwater such as pH, electrical conductivity (EC), total dissolved solids. (TDS), Sodium (Na+) ... of the aquatic systems of the Gadilam river basin show that the groundwater is near-acidic to alkaline and ... leaching of secondary salts and anthropogenic impact by industry and salt water intrusion. Spatial.

  8. Assessment and uncertainty analysis of groundwater risk.

    Science.gov (United States)

    Li, Fawen; Zhu, Jingzhao; Deng, Xiyuan; Zhao, Yong; Li, Shaofei

    2018-01-01

    Groundwater with relatively stable quantity and quality is commonly used by human being. However, as the over-mining of groundwater, problems such as groundwater funnel, land subsidence and salt water intrusion have emerged. In order to avoid further deterioration of hydrogeological problems in over-mining regions, it is necessary to conduct the assessment of groundwater risk. In this paper, risks of shallow and deep groundwater in the water intake area of the South-to-North Water Transfer Project in Tianjin, China, were evaluated. Firstly, two sets of four-level evaluation index system were constructed based on the different characteristics of shallow and deep groundwater. Secondly, based on the normalized factor values and the synthetic weights, the risk values of shallow and deep groundwater were calculated. Lastly, the uncertainty of groundwater risk assessment was analyzed by indicator kriging method. The results meet the decision maker's demand for risk information, and overcome previous risk assessment results expressed in the form of deterministic point estimations, which ignore the uncertainty of risk assessment. Copyright © 2017 Elsevier Inc. All rights reserved.

  9. Hydrogeology and Simulation of Groundwater Flow in the Plymouth-Carver-Kingston-Duxbury Aquifer System, Southeastern Massachusetts

    Science.gov (United States)

    Masterson, John P.; Carlson, Carl S.; Walter, Donald A.; Other contributing authors: Bent, Gardner C.; Massey, Andrew J.

    2009-01-01

    The glacial sediments that underlie the Plymouth-Carver-Kingston-Duxbury area of southeastern Massachusetts compose an important aquifer system that is the primary source of water for a region undergoing rapid development. Population increases and land-use changes in this area has led to two primary environmental effects that relate directly to groundwater resources: (1) increases in pumping that can adversely affect environmentally sensitive groundwater-fed surface waters, such as ponds, streams, and wetlands; and (2) adverse effects of land use on the quality of water in the aquifer. In response to these concerns, the U.S. Geological Survey, in cooperation with the Massachusetts Department of Environmental Protection, began an investigation in 2005 to improve the understanding of the hydrogeology in the area and to assess the effects of changing pumping and recharge conditions on groundwater flow in the Plymouth-Carver-Kingston-Duxbury aquifer system. A numerical flow model was developed based on the USGS computer program MODFLOW-2000 to assist in the analysis of groundwater flow. Model simulations were used to determine water budgets, flow directions, and the sources of water to pumping wells, ponds, streams, and coastal areas. Model-calculated water budgets indicate that approximately 298 million gallons per day (Mgal/d) of water recharges the Plymouth-Carver-Kingston-Duxbury aquifer system. Most of this water (about 70 percent) moves through the aquifer, discharges to streams, and then reaches the coast as surface-water discharge. Of the remaining 30 percent of flow, about 25 percent of the water that enters the aquifer as recharge discharges directly to coastal areas and 5 percent discharges to pumping wells. Groundwater withdrawals are anticipated to increase from the current (2005) rate of about 14 Mgal/d to about 21 Mgal/d by 2030. Pumping from large-capacity production wells decreases water levels and increases the potential for effects on surface

  10. Spatial distribution of groundwater recharge and base flow: Assessment of controlling factors

    Directory of Open Access Journals (Sweden)

    Z. Zomlot

    2015-09-01

    New hydrological insights for the region: The average resulting recharge is 235 mm/year and occurs mainly in winter. The overall moderate correlation between base flow estimates and modeled recharge rates indicates that base flow is a reasonable proxy of recharge. Groundwater recharge variation was explained in order of importance by precipitation, soil texture and vegetation cover; while base flow variation was strongly controlled by vegetation cover and groundwater depth. The results of this study highlight the important role of spatial variables in estimation of recharge and base flow. In addition, the prominent role of vegetation makes clear the potential importance of land-use changes on recharge and hence the need to include a proper strategy for land-use change in sustainable management of groundwater resources.

  11. Variable-density ground-water flow and paleohydrology in the Waste Isolation Pilot Plant (WIPP) region, southeastern New Mexico

    International Nuclear Information System (INIS)

    Davies, P.B.

    1989-01-01

    Variable-density groundwater flow was studied near the Waste Isolation Pilot Plant in southeastern New Mexico. An analysis of the relative magnitude of pressure-related and density-related flow-driving forces indicates that density-related gravity effects are not significant at the plant and to the west but are significant in areas to the north, northeast, and south. A regional-scale model of variable-density groundwater flow in the Culebra Dolomite member of the Rustler Formation indicates that the flow velocities are relatively rapid west of the site and extremely slow east and northeast of the site. In the transition zone between those two extremes, which includes the plant, velocities are highly variable. Sensitivity simulations indicates that the central and western parts of the region, including the plant, are fairly well isolated from the eastern and northeastern boundaries. Vertical-flux simulations indicate that as much as 25% of total inflow to the Culebra could be entering as vertical flow, with most of this flow occurring west of the plant. A simple cross-sectional model was developed to examine the flow system as it drains through time following recharge during a past glacial pluvial. This model indicates that the system as a whole drains very slowly and that it apparently could have sustained flow from purely transient drainage following recharge of the system during the Pleistocene

  12. Hydrogeological and Groundwater Flow Model for C, K, L, and P Reactor Areas, Savannah River Site, Aiken, South Carolina

    International Nuclear Information System (INIS)

    Flach, G.P.

    1999-01-01

    A regional groundwater flow model encompassing approximately 100 mi 2 surrounding the C, K. L. and P reactor areas has been developed. The Reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department

  13. Hydrogeological and Groundwater Flow Model for C, K, L, and P Reactor Areas, Savannah River Site, Aiken, South Carolina

    Energy Technology Data Exchange (ETDEWEB)

    Flach, G.P.

    1999-02-24

    A regional groundwater flow model encompassing approximately 100 mi{sup 2} surrounding the C, K. L. and P reactor areas has been developed. The Reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department.

  14. Investigations of groundwater system and simulation of regional groundwater flow for North Penn Area 7 Superfund site, Montgomery County, Pennsylvania

    Science.gov (United States)

    Senior, Lisa A.; Goode, Daniel J.

    2013-01-01

    Groundwater in the vicinity of several industrial facilities in Upper Gwynedd Township and vicinity, Montgomery County, in southeast Pennsylvania has been shown to be contaminated with volatile organic compounds (VOCs), the most common of which is the solvent trichloroethylene (TCE). The 2-square-mile area was placed on the National Priorities List as the North Penn Area 7 Superfund site by the U.S. Environmental Protection Agency (USEPA) in 1989. The U.S. Geological Survey (USGS) conducted geophysical logging, aquifer testing, and water-level monitoring, and measured streamflows in and near North Penn Area 7 from fall 2000 through fall 2006 in a technical assistance study for the USEPA to develop an understanding of the hydrogeologic framework in the area as part of the USEPA Remedial Investigation. In addition, the USGS developed a groundwater-flow computer model based on the hydrogeologic framework to simulate regional groundwater flow and to estimate directions of groundwater flow and pathways of groundwater contaminants. The study area is underlain by Triassic- and Jurassic-age sandstones and shales of the Lockatong Formation and Brunswick Group in the Mesozoic Newark Basin. Regionally, these rocks strike northeast and dip to the northwest. The sequence of rocks form a fractured-sedimentary-rock aquifer that acts as a set of confined to partially confined layers of differing permeabilities. Depth to competent bedrock typically is less than 20 ft below land surface. The aquifer layers are recharged locally by precipitation and discharge locally to streams. The general configuration of the potentiometric surface in the aquifer is similar to topography, except in areas affected by pumping. The headwaters of Wissahickon Creek are nearby, and the stream flows southwest, parallel to strike, to bisect North Penn Area 7. Groundwater is pumped in the vicinity of North Penn Area 7 for industrial use, public supply, and residential supply. Results of field investigations

  15. Death valley regional ground-water flow model calibration using optimal parameter estimation methods and geoscientific information systems

    Science.gov (United States)

    D'Agnese, F. A.; Faunt, C.C.; Hill, M.C.; Turner, A.K.

    1999-01-01

    A regional-scale, steady-state, saturated-zone ground-water flow model was constructed to evaluate potential regional ground-water flow in the vicinity of Yucca Mountain, Nevada. The model was limited to three layers in an effort to evaluate the characteristics governing large-scale subsurface flow. Geoscientific information systems (GSIS) were used to characterize the complex surface and subsurface hydrogeologic conditions of the area, and this characterization was used to construct likely conceptual models of the flow system. Subsurface properties in this system vary dramatically, producing high contrasts and abrupt contacts. This characteristic, combined with the large scale of the model, make zonation the logical choice for representing the hydraulic-conductivity distribution. Different conceptual models were evaluated using sensitivity analysis and were tested by using nonlinear regression to determine parameter values that are optimal, in that they provide the best match between the measured and simulated heads and flows. The different conceptual models were judged based both on the fit achieved to measured heads and spring flows, and the plausibility of the optimal parameter values. One of the conceptual models considered appears to represent the system most realistically. Any apparent model error is probably caused by the coarse vertical and horizontal discretization.A regional-scale, steady-state, saturated-zone ground-water flow model was constructed to evaluate potential regional ground-water flow in the vicinity of Yucca Mountain, Nevada. The model was limited to three layers in an effort to evaluate the characteristics governing large-scale subsurface flow. Geoscientific information systems (GSIS) were used to characterize the complex surface and subsurface hydrogeologic conditions of the area, and this characterization was used to construct likely conceptual models of the flow system. Subsurface properties in this system vary dramatically, producing

  16. Coupled Modeling of Groundwater Flow and Land Subsidence with Secular Strain (Creep)

    Science.gov (United States)

    Bakr, M.

    2012-12-01

    Land subsidence limits sustainable development of many areas around the world. This is especially the case in low lying regions such as deltas which accommodate a significant percentage of the human population. Among the most common human-induced factors for land subsidence, is groundwater extractions. In these cases, groundwater flow and land subsidence are coupled processes, especially in basins with extensive spatial extent of soft soils (e.g. clay, peat). Creep (or secondary consolidation) is a land subsidence component that usually contributes to total land subsidence in soft soils. It leads to a reduction in void ratio at constant effective stress, and consequently, to the development of an apparent pre-consolidation pressure. The creep component has been usually ignored in the analysis of coupled groundwater flow and land subsidence. Here, the focus is the development of a coupled model of groundwater flow and land subsidence in porous media considering secular strain (creep). The Bjerrum method for settlement calculation (Bjerrum, 1967) due to change in effective stresses is coupled with MODFLOW to tackle the problem. In particular, the SUB-WT package of MODFLOW (Leake and Galloway, 2007) is modified where the Bjerrum method is used to calculate the primary and secondary consolidation due to change in effective stresses as a result of groundwater abstraction. The Bjerrum model is based on linear strains relationship. Usage of linear strains means that the model directly supports the common parameters Cr, Cc, Cα (i.e. re-compression, compression, and secondary compression indices; respectively). The Bjerrum model assumes that creep rate will reduce with increasing over-consolidation and that over-consolidation will grow by unloading and by ageing. To verify the coupled model, a hypothetical problem is considered where a simple hydrogeological system consisting of a shallow unconfined aquifer and a deeper confined aquifer separated by a (semi

  17. Complexity in the validation of ground-water travel time in fractured flow and transport systems

    International Nuclear Information System (INIS)

    Davies, P.B; Hunter, R.L.; Pickens, J.F.

    1991-02-01

    Ground-water travel time is a widely used concept in site assessment for radioactive waste disposal. While ground-water travel time was originally conceived to provide a simple performance measure for evaluating repository sites, its definition in many flow and transport environments is ambiguous. The US Department of Energy siting guidelines (10 CFR 960) define ground-water travel time as the time required for a unit volume of water to travel between two locations, calculated by dividing travel-path length by the quotient of average ground-water flux and effective porosity. Defining a meaningful effective porosity in a fractured porous material is a significant problem. Although the Waste Isolation Pilot Plant (WIPP) is not subject to specific requirements for ground-water travel time, travel times have been computed under a variety of model assumptions. Recently completed model analyses for WIPP illustrate the difficulties in applying a ground-water travel-time performance measure to flow and transport in fractured, fully saturated flow systems. 12 refs., 4 figs

  18. Quasi 3D modeling of water flow in vadose zone and groundwater

    Science.gov (United States)

    Kuznetsov, M.; Yakirevich, A.; Pachepsky, Y. A.; Sorek, S.; Weisbrod, N.

    2012-07-01

    SummaryThe complexity of subsurface flow systems calls for a variety of concepts leading to the multiplicity of simplified flow models. One habitual simplification is based on the assumption that lateral flow and transport in unsaturated zone are not significant unless the capillary fringe is involved. In such cases the flow and transport in the unsaturated zone above groundwater level can be simulated as a 1D phenomenon, whereas the flow and transport through groundwater are viewed as 2D or 3D phenomena. A new approach for a numerical scheme for 3D variably saturated flow using quasi 3D Richards' equation and finite difference scheme is presented. The corresponding numerical algorithm and the QUASI-3D computer code were developed. Results of the groundwater level simulations were compared with transient laboratory experimental data for 2D data constant-flux infiltration, quasi-3D HYDRUS-MODFLOW numerical model and a FULL-3D numerical model using Richards' equation. Hypothetical 3D examples of infiltration, pumping and groundwater mound dissipation for different spatial-time scales are presented. Water flow simulation for the Alto Piura aquifer (Peru) demonstrates the QUASI-3D model application at the regional scale. Computationally the QUASI-3D code was found to be more efficient by an order of 10-300%, while being accurate with respect to the benchmark fully 3D variable saturation code, when the capillary fringe was considered.

  19. First status report on regional ground-water flow modeling for Vacherie Dome, Louisiana

    International Nuclear Information System (INIS)

    1986-07-01

    Regional ground-water flow within the principal geohydrologic units in the vicinity of Vacherie Dome, Louisiana is evaluated by developing a conceptual model of the flow regime within these units and testing the model using a three-dimensional, finite-difference flow code (SWENT). Semiquantitative sensitivity analyses (a limited parametric study) are conducted to define the system responses to changes in the conceptual model, particularly in regard to the geohydrologic properties. All steps leading to the final results and conclusions are incorporated in this report. The available data utilized in this study are summarized. The conceptual model is defined in terms of the areal and vertical averaging of lithologic units, aquifer properties, and hydrologic boundary conditions. The simulated ground-water flow fields are described with potentiometric surfaces, areas of upward and downward flow across aquitards, tables summarizing the horizontal and vertical volumetric flows through the principal units, ground-water travel times and paths, and Darcy velocities within specified finite-difference blocks. The reported work is the first stage of an ongoing evaluation of Vacherie Dome as a potential repository for high-level radioactive wastes. The results and conclusions should thus be considered preliminary and subject to modification with the collection of additional data. However, the report does provide a useful basis for describing the sensitivity of the conceptualization of ground-water flow to parameterization and, to a lesser extent, the uncertainties in the present conceptualization. 34 refs., 57 figs., 19 tabs

  20. Boundary delineation for regional groundwater flow through geographic information system (Contract research)

    International Nuclear Information System (INIS)

    Yamakawa, Tadashi; Munakata, Masahiro; Kimura, Hideo; Hyodo, Hiroshi

    2007-03-01

    Radionuclide migration toward the human environment is to be assessed as the part of long-term safety assessments of geologic disposal of radioactive waste. Geologic processes, which include volcanic activity, hydrothermal activity, seismicity and deformation, bring about hydrogeologic changes in the regional groundwater flow system around a repository site. Groundwater flow systems in Japan have been studied in several sites such as Tono mine, Kamaishi mine and Horonobe area, but methodology of studies in these sites does not have fully developed. This study was conducted to develop methodologies of boundary delineation for regional groundwater flow systems. Geographic Information System, GIS, was applied using available topographic, hydrologic and geologic data for an area of interest. Miyakoji in the Abukuma Mountains was selected as the area, for the reason of its simple geologic setting formed by granitic rocks and topographically gentle hills of drainage basin. Data used in this study cover topographic sheets, digital elevation model, satellite imagery, geologic maps, topographic classification maps, soil distribution maps and landuse maps. Through the GIS techniques using these data, thematic maps on topographic features, surface conditions, land coverage, geology and geologic structure and weathered crust were developed, and these thematic maps were further applied to extract four factors affecting the regional groundwater flows: topographic condition, precipitation recharge, fracture characteristics and potential flows. The present study revealed that, taking the potential groundwater flows and characteristics of fractured zones in the area into consideration, the groundwater flow system in Miyakoji drainage basin should be bounded by the Otakine Mountain and the northern part of Tokoha Drainage Basin. The delineated area is larger than understood before. (author)

  1. Mathematical modelling of surface water-groundwater flow and salinity interactions in the coastal zone

    Science.gov (United States)

    Spanoudaki, Katerina; Kampanis, Nikolaos A.

    2014-05-01

    Coastal areas are the most densely-populated areas in the world. Consequently water demand is high, posing great pressure on fresh water resources. Climatic change and its direct impacts on meteorological variables (e.g. precipitation) and indirect impact on sea level rise, as well as anthropogenic pressures (e.g. groundwater abstraction), are strong drivers causing groundwater salinisation and subsequently affecting coastal wetlands salinity with adverse effects on the corresponding ecosystems. Coastal zones are a difficult hydrologic environment to represent with a mathematical model due to the large number of contributing hydrologic processes and variable-density flow conditions. Simulation of sea level rise and tidal effects on aquifer salinisation and accurate prediction of interactions between coastal waters, groundwater and neighbouring wetlands requires the use of integrated surface water-groundwater models. In the past few decades several computer codes have been developed to simulate coupled surface and groundwater flow. In these numerical models surface water flow is usually described by the 1-D Saint Venant equations (e.g. Swain and Wexler, 1996) or the 2D shallow water equations (e.g. Liang et al., 2007). Further simplified equations, such as the diffusion and kinematic wave approximations to the Saint Venant equations, are also employed for the description of 2D overland flow and 1D stream flow (e.g. Gunduz and Aral, 2005). However, for coastal bays, estuaries and wetlands it is often desirable to solve the 3D shallow water equations to simulate surface water flow. This is the case e.g. for wind-driven flows or density-stratified flows. Furthermore, most integrated models are based on the assumption of constant fluid density and therefore their applicability to coastal regions is questionable. Thus, most of the existing codes are not well-suited to represent surface water-groundwater interactions in coastal areas. To this end, the 3D integrated

  2. A coupled groundwater-flow-modelling and vulnerability-mapping methodology for karstic terrain management

    Science.gov (United States)

    Kavouri, Konstantina P.; Karatzas, George P.; Plagnes, Valérie

    2017-08-01

    A coupled groundwater-flow-modelling and vulnerability-mapping methodology for the management of karst aquifers with spatial variability is developed. The methodology takes into consideration the duality of flow and recharge in karst and introduces a simple method to integrate the effect of temporal storage in the unsaturated zone. In order to investigate the applicability of the developed methodology, simulation results are validated against available field measurement data. The criteria maps from the PaPRIKa vulnerability-mapping method are used to document the groundwater flow model. The FEFLOW model is employed for the simulation of the saturated zone of Palaikastro-Chochlakies karst aquifer, in the island of Crete, Greece, for the hydrological years 2010-2012. The simulated water table reproduces typical karst characteristics, such as steep slopes and preferred drain axes, and is in good agreement with field observations. Selected calculated error indicators—Nash-Sutcliffe efficiency (NSE), root mean squared error (RMSE) and model efficiency (E')—are within acceptable value ranges. Results indicate that different storage processes take place in different parts of the aquifer. The north-central part seems to be more sensitive to diffuse recharge, while the southern part is affected primarily by precipitation events. Sensitivity analysis is performed on the parameters of hydraulic conductivity and specific yield. The methodology is used to estimate the feasibility of artificial aquifer recharge (AAR) at the study area. Based on the developed methodology, guidelines were provided for the selection of the appropriate AAR scenario that has positive impact on the water table.

  3. Comparing groundwater recharge and base flow in the Bukmoongol ...

    Indian Academy of Sciences (India)

    It can be used for comparing alternate flow regimes, identifying changes in a flow regime through time and for generating flow statistics that can be used to predict the likely ... The Lyn–Hollick filter equation in calculating the base flow component of the hydrograph in RAP software is shown below. It has an alpha value of.

  4. Application of MODFLOW and geographic information system to groundwater flow simulation in North China Plain, China

    Science.gov (United States)

    Wang, Shiqin; Shao, Jingli; Song, Xianfang; Zhang, Yongbo; Huo, Zhibin; Zhou, Xiaoyuan

    2008-10-01

    MODFLOW is a groundwater modeling program. It can be compiled and remedied according to the practical applications. Because of its structure and fixed data format, MODFLOW can be integrated with Geographic Information Systems (GIS) technology for water resource management. The North China Plain (NCP), which is the politic, economic and cultural center of China, is facing with water resources shortage and water pollution. Groundwater is the main water resource for industrial, agricultural and domestic usage. It is necessary to evaluate the groundwater resources of the NCP as an entire aquifer system. With the development of computer and internet information technology it is also necessary to integrate the groundwater model with the GIS technology. Because the geological and hydrogeological data in the NCP was mainly in MAPGIS format, the powerful function of GIS of disposing of and analyzing spatial data and computer languages such as Visual C and Visual Basic were used to define the relationship between the original data and model data. After analyzing the geological and hydrogeological conditions of the NCP, the groundwater flow numerical simulation modeling was constructed with MODFLOW. On the basis of GIS, a dynamic evaluation system for groundwater resources under the internet circumstance was completed. During the process of constructing the groundwater model, a water budget was analyzed, which showed a negative budget in the NCP. The simulation period was from 1 January 2002 to 31 December 2003. During this period, the total recharge of the groundwater system was 49,374 × 106 m3 and the total discharge was 56,530 × 106 m3 the budget deficit was -7,156 × 106 m3. In this integrated system, the original data including graphs and attribution data could be stored in the database. When the process of evaluating and predicting groundwater flow was started, these data were transformed into files that the core program of MODFLOW could read. The calculated water

  5. Evaluation of in situ sulfate reduction as redox buffer capacity in groundwater flow path

    International Nuclear Information System (INIS)

    Ioka, Seiichiro; Iwatsuki, Teruki; Amano, Yuki; Furue, Ryoji

    2007-01-01

    For safety assessment of geological isolation, it is important to evaluate in situ redox buffer capacity in high-permeability zone as groundwater flow path. The study evaluated in situ sulfate reduction as redox buffer capacity in the conglomerate bedding in Toki Lignite-bearing Formation, which occurs at the lowest part of sedimentary rocks overlying basement granite. The bedding plays an important role as the main groundwater flow path. The result showed that in situ redox buffer capacity in the conglomerate bedding has been identified on first nine months, whereas in the following period the redox buffer capacity has not been identified for about fifteen months. This will be caused by the bedding became inappropriate for microbial survival as the organic matter which is needfuel for microbial activity was consumed. Thus, there will be limited redox buffer capacity in groundwater flow path even in formation including organic matter-bearing layer. (author)

  6. Groundwater flow in the Venice lagoon and remediation of the Porto Marghera industrial area (Italy)

    Science.gov (United States)

    Beretta, Giovanni Pietro; Terrenghi, Jacopo

    2017-05-01

    This study aims to determine the groundwater flow in a large area of the Venice (northeast Italy) lagoon that is under great anthropogenic pressure, which is influencing the regional flow in the surficial aquifer (about 30 m depth). The area presents several elements that condition the groundwater flow: extraction by means of drainage pumps and wells; tidal fluctuation; impermeable barriers that define part of the coastline, rivers and artificial channels; precipitation; recharge, etc. All the elements were studied separately, and then they were brought together in a numerical groundwater flow model to estimate the impact of each one. Identification of the impact of each element will help to optimise the characteristics of the Porto Marghera remediation systems. Longstanding industrial activity has had a strong impact on the soil and groundwater quality, and expensive and complex emergency remediation measures in problematic locations have been undertaken to ensure the continuity of industrial and maritime activities. The land reclamation and remediation works withdraw 56-74% of the water budget, while recharge from the river accounts for about 21-48% of the input. Only 21-42% of groundwater in the modelled area is derived from natural recharge sources, untouched by human activity. The drop of the piezometric level due to the realization of the upgradient impermeable barrier can be counteracted with the reduction of the pumping rate of the remediation systems.

  7. Site-scale groundwater flow modelling of Aberg

    International Nuclear Information System (INIS)

    Walker, D.; Gylling, B.

    1998-12-01

    The Swedish Nuclear Fuel and Waste Management Company (SKB) SR 97 study is a comprehensive performance assessment illustrating the results for three hypothetical repositories in Sweden. In support of SR 97, this study examines the hydrogeologic modelling of the hypothetical site called Aberg, which adopts input parameters from the Aespoe Hard Rock Laboratory in southern Sweden. This study uses a nested modelling approach, with a deterministic regional model providing boundary conditions to a site-scale stochastic continuum model. The model is run in Monte Carlo fashion to propagate the variability of the hydraulic conductivity to the advective travel paths from representative canister locations. A series of variant cases addresses uncertainties in the inference of parameters and the boundary conditions. The study uses HYDRASTAR, the SKB stochastic continuum groundwater modelling program, to compute the heads, Darcy velocities at each representative canister position and the advective travel times and paths through the geosphere. The nested modelling approach and the scale dependency of hydraulic conductivity raise a number of questions regarding the regional to site-scale mass balance and the method's self-consistency. The transfer of regional heads via constant head boundaries preserves the regional pattern recharge and discharge in the site-scale model, and the regional to site-scale mass balance is thought to be adequate. The upscaling method appears to be approximately self-consistent with respect to the median performance measures at various grid scales. A series of variant cases indicates that the study results are insensitive to alternative methods on transferring boundary conditions from the regional model to the site-scale model. The flow paths, travel times and simulated heads appear to be consistent with on-site observations and simple scoping calculations. The variabilities of the performance measures are quite high for the Base Case, but the

  8. Development og groundwater flow modeling techniques for the low-level radwaste disposal (III)

    Energy Technology Data Exchange (ETDEWEB)

    Bae, Dae-Seok; Kim, Chun-Soo; Kim, Kyung-Soo; Park, Byung-Yoon; Koh, Yong-Kweon; Park, Hyun-Soo [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2000-12-01

    The project amis to establish the methodology of hydrogeologic assessment by the field application of the evaluation techniques gained and accumulated from the previous hydrogeological research works in Korea. The results of the project and their possible areas for application are (1) acquisition of detailed hydrogeologic information by using a borehole televiewer and a multipacker system, (2) establishing an integrated hydrogeological assessment method for fractured rocks, (3) acquisition of the fracture parameters for fracture modeling, (4) an inversion analysis of hydraulic parameters from fracture network modeling, (5) geostatistical methods for the spatial assignment of hydraulic parameters for fractured rocks, and (6) establishing the groundwater flow modeling procedure for a repository. 75 refs., 72 figs., 34 tabs. (Author)

  9. Cash flow analysis

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This chapter addresses the cash flow analysis of dual-purpose power plants. The topics discussed include the impact of inflation (including the relative inflation of individual cost components such as purchased power, supplemental power, standby charges, buy back rate, heating fuel costs, power plants costs, staffing, maintenance, insurance, and administrative charges), controlling costs, purchased power and fuel price projections, varying the assumptions, financing, and modeling of tax impacts

  10. Evaluation of multiple tracer methods to estimate low groundwater flow velocities.

    Science.gov (United States)

    Reimus, Paul W; Arnold, Bill W

    2017-04-01

    Four different tracer methods were used to estimate groundwater flow velocity at a multiple-well site in the saturated alluvium south of Yucca Mountain, Nevada: (1) two single-well tracer tests with different rest or "shut-in" periods, (2) a cross-hole tracer test with an extended flow interruption, (3) a comparison of two tracer decay curves in an injection borehole with and without pumping of a downgradient well, and (4) a natural-gradient tracer test. Such tracer methods are potentially very useful for estimating groundwater velocities when hydraulic gradients are flat (and hence uncertain) and also when water level and hydraulic conductivity data are sparse, both of which were the case at this test location. The purpose of the study was to evaluate the first three methods for their ability to provide reasonable estimates of relatively low groundwater flow velocities in such low-hydraulic-gradient environments. The natural-gradient method is generally considered to be the most robust and direct method, so it was used to provide a "ground truth" velocity estimate. However, this method usually requires several wells, so it is often not practical in systems with large depths to groundwater and correspondingly high well installation costs. The fact that a successful natural gradient test was conducted at the test location offered a unique opportunity to compare the flow velocity estimates obtained by the more easily deployed and lower risk methods with the ground-truth natural-gradient method. The groundwater flow velocity estimates from the four methods agreed very well with each other, suggesting that the first three methods all provided reasonably good estimates of groundwater flow velocity at the site. The advantages and disadvantages of the different methods, as well as some of the uncertainties associated with them are discussed. Published by Elsevier B.V.

  11. Geohydrology, simulation of regional groundwater flow, and assessment of watermanagement strategies, Twentynine Palms area, California

    Science.gov (United States)

    Li, Zhen; Martin, Peter

    2011-01-01

    aquifers (referred to as the upper and the middle aquifers) and the Tertiary sedimentary deposits into a single aquifer (referred to as the lower aquifer). In general, wells perforated in the upper aquifer yield more water than wells perforated in the middle and lower aquifers. The study area is dominated by extensive faulting and moderate to intense folding that has displaced or deformed the pre-Tertiary basement complex as well as the overlying Tertiary and Quaternary deposits. Many of these faults act as barriers to the lateral movement of groundwater flow and form many of the boundaries of the groundwater subbasins. The principal recharge to the study area is groundwater underflow across the western and southern boundaries that originates as runoff in the surrounding mountains. Groundwater discharges naturally from the study area as spring flow, as groundwater underflow to downstream basins, and as water vapor to the atmosphere by transpiration of phreatophytes and direct evaporation from moist soil. The annual volume of water that naturally recharged to or discharged from the groundwater flow system in the study area during predevelopment conditions was estimated to be 1,010 acre-feet per year (acre-ft/yr). About 90 percent of this recharge originated as runoff from the Little San Bernardino and the Pinto Mountains to the south, and the remainder originated as runoff from the San Bernardino Mountains to the west. Evapotranspiration by phreatophytes near Mesquite Lake (dry) was the primary form of predevelopment groundwater discharge. From 1953 through 2007, approximately 139,400 acre-feet (acre-ft) of groundwater was pumped by the MCAGCC from the Surprise Spring subbasin. A regional-scale numerical groundwater flow model was developed using MODFLOW-2000 for the Surprise Spring, Deadman, Mesquite, and Mainside subbasins. The aquifer system was simulated by using three model layers representing the upper, middle, and lower aquifers. Measured groundwater levels

  12. Effect of Borehole Material on Analytical Solutions of the Heat Transfer Model of Ground Heat Exchangers Considering Groundwater Flow

    Directory of Open Access Journals (Sweden)

    Sangwoo Park

    2016-04-01

    Full Text Available Groundwater flow is one of the most important factors for the design of a ground heat exchanger (GHEX since the thermal environment of the ground around the buried GHEX is significantly affected by heat convection due to the groundwater flow. Several preceding studies have been conducted to develop analytical solutions to the heat transfer model of GHEX with consideration of groundwater flow. One of these solutions is the combined heat transfer model of conduction and convection. However, the developed combined analytical models are inapplicable to all of the configurations of ordinary GHEXs because these solutions assume that the inner part of the borehole is thermally inert or consists of the same material as that of the surrounding ground. In this paper, the applicability of the combined solid cylindrical heat source model, which is the most suitable to energy piles until now, was evaluated by performing a series of numerical analyses. In the numerical analysis, the inner part of the borehole was modeled as two different materials (i.e., permeable ground formation and impermeable fill such as concrete to evaluate applicability of the analytical solution along with different diameter-length (D/L ratios of borehole. In a small value of the D/L ratio, the analytical solution to the combined heat transfer model is in good agreement with the result of numerical analysis. On the other hand, when increasing the D/L ratio, the analytical solution significantly overestimates the effect of groundwater flow on the heat transfer of GHEXs because the analytical solution disregards the existence of the impermeable region in the borehole. Consequently, such tendency is more critical in the GHEX with a large D/L ratio such as large-diameter energy piles.

  13. Quasi 3D modeling of water flow and solute transport in vadose zone and groundwater

    Science.gov (United States)

    Yakirevich, A.; Kuznetsov, M.; Weisbrod, N.; Pachepsky, Y. A.

    2013-12-01

    The complexity of subsurface flow systems calls for a variety of concepts leading to the multiplicity of simplified flow models. One commonly used simplification is based on the assumption that lateral flow and transport in unsaturated zone is insignificant unless the capillary fringe is involved. In such cases the flow and transport in the unsaturated zone above groundwater level can be simulated as a 1D phenomenon, whereas through groundwater they are viewed as 2D or 3D phenomena. A new approach for a numerical scheme for 3D variably saturated flow and transport is presented. A Quasi-3D approach allows representing flow in the 'vadose zone - aquifer' system by a series of 1D Richards' equations solved in variably-saturated zone and by 3D-saturated flow equation in groundwater (modified MODFLOW code). The 1D and 3D equations are coupled at the phreatic surface in a way that aquifer replenishment is calculated using the Richards' equation, and solving for the moving water table does not require definition of the specific yield parameter. The 3D advection-dispersion equation is solved in the entire domain by the MT3D code. Using implicit finite differences approximation to couple processes in the vadose zone and groundwater provides mass conservation and increase of computational efficiency. The above model was applied to simulate the impact of irrigation on groundwater salinity in the Alto Piura aquifer (Northern Peru). Studies on changing groundwater quality in arid and semi-arid lands show that irrigation return flow is one of the major factors contributing to aquifer salinization. Existing mathematical models do not account explicitly for the solute recycling during irrigation on a daily scale. Recycling occurs throughout the unsaturated and saturated zones, as function of the solute mass extracted from pumping wells. Salt concentration in irrigation water is calculated at each time step as a function of concentration of both surface water and groundwater

  14. Ground-water sample collection and analysis plan for the ground-water surveillance project

    International Nuclear Information System (INIS)

    Bryce, R.W.; Evans, J.C.; Olsen, K.B.

    1991-12-01

    The Pacific Northwest Laboratory performs ground-water sampling activities at the US Department of Energy's (DOE's) Hanford Site in support of DOE's environmental surveillance responsibilities. The purpose of this document is to translate DOE's General Environmental Protection Program (DOE Order 5400.1) into a comprehensive ground-water sample collection and analysis plan for the Hanford Site. This sample collection and analysis plan sets forth the environmental surveillance objectives applicable to ground water, identifies the strategy for selecting sample collection locations, and lists the analyses to be performed to meet those objectives

  15. Understanding large scale groundwater flow to aid in repository siting

    International Nuclear Information System (INIS)

    Davison, C.C.; Brown, A.; Gascoyne, M.; Stevenson, D.R.; Ophori, D.U.

    1996-01-01

    Atomic Energy of Canada Limited (AECL) with support from Ontario Hydro has developed a concept for the safe disposal of Canada's nuclear fuel waste in a deep (500 to 1000 m) mined repository in plutonic rocks of the Canadian Shield. The disposal concept involves the use of multiple engineered and natural barriers to ensure long-term safety. The geosphere, comprised of the enclosing rock mass and the groundwater which occurs in cracks and pores in the rock, is expected to serve as an important natural barrier to the release and migration of wastes from the engineered repository. Although knowledge of the physical and chemical characteristics of the groundwater in the rock at potential repository sites is needed to help design the engineered barriers of the repository it can also be used to aid in repository siting, to take greater advantage of natural conditions in the geosphere to enhance its role as a barrier in the overall disposal system

  16. Reconstructing the groundwater flow in the Baltic Basin during the Last glaciation

    Science.gov (United States)

    Saks, T.; Sennikovs, J.; Timuhins, A.; Kalvāns, A.

    2012-04-01

    In last decades it has been discussed that most large ice sheets tend to reside on warm beds even in harsh clima tic conditions and subglacial melting occurs due to geothermal heat flow and deformation heat of the ice flow. However the subglacial groundwater recharge and flow conditions have been addressed in only few studies. The aim of this study is to establish the groundwater flow pattern in the Baltic Basin below the Scandinavian ice sheet during the Late Weichselian glaciation. The calculation results are compared to the known distribution of the groundwater body of the glacial origin found in Cambrian - Vendian (Cm-V) aquifer in the Northern Estonia which is believed to have originated as a result of subglacial meltwater infiltration during the reoccurring glaciations. Steady state regional groundwater flow model of the Baltic Basin was used to simulate the groundwater flow beneath the ice sheet with its geometry adjusted to reflect the subglacial topography. Ice thickness modelling data (Argus&Peltier, 2010) was used for the setup of the boundary conditions: the meltwater pressure at the ice bed was assumed equal to the overlying ice mass. The modelling results suggest two main recharge areas of the Cm-V aquifer system, and reversed groundwater flow that persisted for at least 14 thousand years. Model results show that the groundwater flow velocities in the Cm-V aquifer in the recharge area in N-Estonia beneath the ice sheet exceeded the present velocities by a factor of 10 on average. The calculated meltwater volume recharged into the Cm-V aquifer system during the Late Weichselian corresponds roughly to the estimated, however, considering the fact, that the study area has been glaciated at least 4 times this is an overestimation. The modeling results attest the hypothesis of light dO18 groundwater glacial origin in the Cm-V aquifer system, however the volumes, timing and processes involved in the meltwater intrusion are yet to be explored. This study was

  17. Outline of the integrated simulation system (GEOMASS system) to evaluate groundwater flow and application to groundwater simulation in the Tono area

    Energy Technology Data Exchange (ETDEWEB)

    Inaba, Kaoru; Saegusa, Hiromitsu [Japan Nuclear Cycle Development Inst., Toki, Gifu (Japan). Tono Geoscience Center

    2003-03-01

    The Tono Geoscience Center (TGC) has been developing the GEOMASS system since 1997 to evaluate the groundwater flow at depth in a rock mass. The system provides an integrated simulation system environment for both model development and groundwater flow simulations. The integrated simulation system allows users to use resources efficiently. The system also allows users to make rapid improvement of their models as data increases. Also, it is possible to perform more realistic groundwater flow simulations due to the capability of modeling the rock mass as a continuum with discrete hydro-structural features in the rock. TGC tested the operation and usefulness of the GEOMASS system by applying to groundwater flow simulations in the Tono area, Gifu Prefecture. TGC confirmed that the system is very useful for complex geological models and multiple modeling. (author)

  18. Death Valley regional groundwater flow model calibration using optimal parameter estimation methods and geoscientific information systems

    Science.gov (United States)

    D'Agnese, F. A.; Faunt, C.C.; Hill, M.C.; Turner, A.K.

    1996-01-01

    A three-layer Death Valley regional groundwater flow model was constructed to evaluate potential regional groundwater flow paths in the vicinity of Yucca Mountain, Nevada. Geoscientific information systems were used to characterize the complex surface and subsurface hydrogeological conditions of the area, and this characterization was used to construct likely conceptual models of the flow system. The high contrasts and abrupt contacts of the different hydrogeological units in the subsurface make zonation the logical choice for representing the hydraulic conductivity distribution. Hydraulic head and spring flow data were used to test different conceptual models by using nonlinear regression to determine parameter values that currently provide the best match between the measured and simulated heads and flows.

  19. The Experience at Russian Nuclear Sites of Modeling Groundwater Flow on Different Scales

    Science.gov (United States)

    Zinin, A.; Zinina, G.; Samsanova, L.; Vasilkova, N.; Alexandrova, L.; Drozhko, E.

    2001-12-01

    The experience of developing models of different scales to predict contaminant plume migration in ground waters is analyzed. The method of developing a three-dimensional transient model is demonstrated to estimate high-density solutions migrating from the surface storage of liquid radioactive waste, using a two-dimensional regional model for setting boundary conditions (Lake Karachay, PA "Mayak", Russia). The model is used to calculate three-dimensional transient distribution of pressure, density and concentrations of the dissolved admixtures in the non-confined aquifers. Interpolation is also specified to calculate boundary conditions parameters of the inserted models. The method of constructing a local filtration model is described to predict the contaminant plume spreading from the operating ground of deep burial of liquid radioactive wastes (The Siberian Chemical Plant, Seversk). The local model uses smaller grid gaps over time and space and a more detailed stratiographic division of the section as compared to the regional model intended to be used for estimating groundwater resourses. The flow distribution within the local model boundaries is described as the products of an average annual flow and periodical time function (function of monthly fluctuations) and the function of spatial variables. The parameters of the distribution function, represented on the local model grid by the values, were determined by solving the inverse problem. The sensivity analysis of the target function of the inverse problem to the small variations of the average annual flows is described.

  20. A Modified Groundwater Flow Model Using the Space Time Riemann-Liouville Fractional Derivatives Approximation

    Directory of Open Access Journals (Sweden)

    Abdon Atangana

    2014-01-01

    Full Text Available The notion of uncertainty in groundwater hydrology is of great importance as it is known to result in misleading output when neglected or not properly accounted for. In this paper we examine this effect in groundwater flow models. To achieve this, we first introduce the uncertainties functions u as function of time and space. The function u accounts for the lack of knowledge or variability of the geological formations in which flow occur (aquifer in time and space. We next make use of Riemann-Liouville fractional derivatives that were introduced by Kobelev and Romano in 2000 and its approximation to modify the standard version of groundwater flow equation. Some properties of the modified Riemann-Liouville fractional derivative approximation are presented. The classical model for groundwater flow, in the case of density-independent flow in a uniform homogeneous aquifer is reformulated by replacing the classical derivative by the Riemann-Liouville fractional derivatives approximations. The modified equation is solved via the technique of green function and the variational iteration method.

  1. Water scarcity, groundwater and base flow in Dutch catchments: effects of climate and human impact

    Science.gov (United States)

    Hendriks, D. M. D.; van Ek, R.; Kuijper, M. J. M.

    2012-04-01

    During recent years (2003, 2006 en 2008) water boards in the Netherlands have had to cope with drought and water scarcity. Because of human impacts in the area, like groundwater abstraction and extensive drainage, the upper parts of streams run dry during low precipitation periods. The lack of water is a risk for the environmental flow needs of the streams. In addition, agricultural areas encounter problems due to low groundwater levels and limited availability of water for spray irrigation. Such problems are likely to occur more frequent in the future, because of increasing frequency of dry spells, reduced water intake possibilities from large rivers and a higher demand for water for agriculture and other land use functions. Several studies have been carried out to investigate the possibilities for structural improvement of groundwater and base flow conditions, thereby improving the situation of agriculture and ecology (Hendriks et al., 2010; Kuijper et al., 2012). The effects of both climate change and unsustainable use of water resources on base flow were assessed at various scales. For this purpose, spatially distributed groundwater models with fine meshed grids (25x25 m) were used to simultaneously assess the effects of climate and human impacts on both groundwater conditions and surface water discharge. Climatic effects were assessed by comparison of meteorologically dry and average years, as well as through climate scenarios from the Royal Dutch Weather Service (KNMI). Human impacts were assessed by modeling various scenarios with reduced or increased drainage and groundwater abstraction, including a scenario of the undisturbed situation. Also, the impact of stream morphology was studied. The suitability of a new modeling approach (Van der Velde et al., 2009), allowing a fast assessment of discharge with high accuracy, was tested to improve discharge simulations from groundwater models. Model results show that extensive drainage systems have a large impact

  2. Evaluation of particle release from montmorillonite gel by flowing groundwater based on the DLVO theory

    International Nuclear Information System (INIS)

    Kurosawa, Susumu; Nagasaki, Shinya; Tanaka, Satoru

    2007-01-01

    Theoretical study has been performed to clarify the ability of colloid release form the montmorillonite gel by the flowing groundwater. Evaluation of montmorillonite colloidal particles release from the bentonite buffer material is important for the performance assessment of radioactive waste disposal because the colloids may influence the radionuclide transport. In this study, the minimum groundwater flow rate required to tear off montmorillonite particles from surface of bentonite buffer was estimated from the shear stress on the gel front, which was calculated by the DLVO theory. The estimated shear force was converted to corresponding groundwater velocity by using Stoke's equation. The results indicated that groundwater velocity in a range of about 10 -5 to 10 -4 m/s would be necessary to release montmorillonite particles. This range is higher than the groundwater flow velocity found generally in deep geological media in Japan. This study suggests that the effect of montmorillonite particles release from the bentonite buffer on radionuclide transport is likely to be negligible in the performance assessment of high-level radioactive waste geological disposal. (author)

  3. Concepts of Groundwater Occurrence and Flow Near Oak Ridge National Laboratory, Tennessee

    International Nuclear Information System (INIS)

    Moore, G.K.

    1988-01-01

    Previous studies of the area near Oak Ridge National Laboratory (ORNL) assumed that nearly all groundwater from precipitation and infiltration moves vertically down to the water table and then follows a combination of intergranular and fracture flow paths to the streams. These studies also generally assumed nearly linear flow paths, amounts of groundwater flow that are determined by differences in water-level elevation, large permeability differences between regolith and bedrock, and important hydrologic differences between named geologic units. It has been commonly stated for 37 years, for example, that the Conasauga Group has fewer cavities and is less permeable than the Chickamauga Group. All of these assumptions and conclusions are faulty. The new concepts in this report may be controversial, but they explain the available data. Only the stormflow zone from land surface to a depth of 1-2 m has a permeability large enough to transport most groundwater to the streams. Calculations show that 90-95% of all groundwater flow is in the stormflow zone, 4-9% is in a few water-producing intervals below the water table, and about 1% occurs in other intervals. The available data also show that nearly all groundwater flows through enlarged openings such as macropores, fractures, and cavities, and that there are no significant differences between regolith and bedrock or between the Conasauga Group and the Chickamauga group. Flow paths apparently are much more complex than was previously assumed. Multiple paths connect any two points below the water table, and each flow path is more likely to be tortuous than linear. Hydraulic gradients are affected by this complexity and by changes in hydraulic potential on steep hillsides. Below the water table, a large difference in the head of two points generally does not indicate a large flow rate between these points. Groundwater storage in amounts above field capacity is apparently intergranular in only the stormflow and vadose zones

  4. Groundwater flow system stability in shield settings a multi-disciplinary approach

    International Nuclear Information System (INIS)

    Jensen, M.R.; Goodwin, B.W.

    2004-01-01

    Within the Deep Geologic Repository Technology Program (DGRTP) several Geoscience activities are focused on advancing the understanding of groundwater flow system evolution and geochemical stability in a Shield setting as affected by long-term climate change. A key aspect is developing confidence in predictions of groundwater flow patterns and residence times as they relate to the safety of a Deep Geologic Repository for used nuclear fuel waste. A specific focus in this regard has been placed on constraining redox stability and groundwater flow system dynamics during the Pleistocene. Attempts are being made to achieve this through a coordinated multi-disciplinary approach intent on; i) demonstrating coincidence between independent geo-scientific data; ii) improving the traceability of geo-scientific data and its interpretation within a conceptual descriptive model(s); iii) improving upon methods to assess and demonstrate robustness in flow domain prediction(s) given inherent flow domain uncertainties (i.e. spatial chemical/physical property distributions; boundary conditions) in time and space; and iv) improving awareness amongst geo-scientists as to the utility various geo-scientific data in supporting a repository safety case. Coordinated by the DGRTP, elements of this program include the development of a climate driven Laurentide ice-sheet model to constrain the understanding of time rate of change in boundary conditions most affecting the groundwater flow domain and its evolution. Further work has involved supporting WRA Paleo-hydrogeologic studies in which constrained thermodynamic analyses coupled with field studies to characterize the paragenesis of fracture infill mineralogy are providing evidence to premise understandings of possible depth of penetration by oxygenated glacial recharge. In parallel. numerical simulations have been undertaken to illustrate aspect of groundwater flow system stability and evolution in a Shield setting. Such simulations

  5. Water transfers, agriculture, and groundwater management: a dynamic economic analysis.

    Science.gov (United States)

    Knapp, Keith C; Weinberg, Marca; Howitt, Richard; Posnikoff, Judith F

    2003-04-01

    Water transfers from agricultural to urban and environmental uses will likely become increasingly common worldwide. Many agricultural areas rely heavily on underlying groundwater aquifers. Out-of-basin surface water transfers will increase aquifer withdrawals while reducing recharge, thereby altering the evolution of the agricultural production/groundwater aquifer system over time. An empirical analysis is conducted for a representative region in California. Transfers via involuntary surface water cutbacks tilt the extraction schedule and lower water table levels and net benefits over time. The effects are large for the water table but more modest for the other variables. Break-even prices are calculated for voluntary quantity contract transfers at the district level. These prices differ considerably from what might be calculated under a static analysis which ignores water table dynamics. Canal-lining implies that districts may gain in the short-run but lose over time if all the reduction in conveyance losses is transferred outside the district. Water markets imply an evolving quantity of exported flows over time and a reduction in basin net benefits under common property usage. Most aquifers underlying major agricultural regions are currently unregulated. Out-of-basin surface water transfers increase stress on the aquifer and management benefits can increase substantially in percentage terms but overall continue to remain small. Conversely, we find that economically efficient management can mitigate some of the adverse consequences of transfers, but not in many circumstances or by much. Management significantly reduced the water table impacts of cutbacks but not annual net benefit impacts. Neither the break-even prices nor the canal-lining impacts were altered by much. The most significant difference is that regional water users gain from water markets under efficient management.

  6. Budgets and chemical characterization of groundwater for the Diamond Valley flow system, central Nevada, 2011–12

    Science.gov (United States)

    Berger, David L.; Mayers, C. Justin; Garcia, C. Amanda; Buto, Susan G.; Huntington, Jena M.

    2016-07-29

    The Diamond Valley flow system consists of six hydraulically connected hydrographic areas in central Nevada. The general down-gradient order of the areas are southern and northern Monitor Valleys, Antelope Valley, Kobeh Valley, Stevens Basin, and Diamond Valley. Groundwater flow in the Diamond Valley flow system terminates at a large playa in the northern part of Diamond Valley. Concerns relating to continued water-resources development of the flow system resulted in a phased hydrologic investigation that began in 2005 by the U.S. Geological Survey in cooperation with Eureka County. This report presents the culmination of the phased investigation to increase understanding of the groundwater resources of the basin-fill aquifers in the Diamond Valley flow system through evaluations of groundwater chemistry and budgets. Groundwater chemistry was characterized using major ions and stable isotopes from groundwater and precipitation samples. Groundwater budgets accounted for all inflows, outflows, and changes in storage, and were developed for pre-development (pre-1950) and recent (average annual 2011–12) conditions. Major budget components include groundwater discharge by evapotranspiration and groundwater withdrawals; groundwater recharge by precipitation, and interbasin flow; and storage change.

  7. GEOCHEMICAL AND ISOTOPIC CONSTRAINTS ON GROUND-WATER FLOW DIRECTIONS, MIXING AND RECHARGE AT YUCCA MOUNTAIN, NEVADA

    International Nuclear Information System (INIS)

    A. Meijer; E. Kwicklis

    2000-01-01

    This analysis is governed by the Office of Civilian Radioactive Waste Management (OCRWM) Analysis and Modeling Report Development Plan entitled ''Geochemical and Isotopic Constraints on Groundwater Flow Directions, Mixing and Recharge at Yucca Mountain'' (CRWMS M and O 1999a). As stated in this Development Plan, the purpose of the work is to provide an analysis of groundwater recharge rates, flow directions and velocities, and mixing proportions of water from different source areas based on groundwater geochemical and isotopic data. The analysis of hydrochemical and isotopic data is intended to provide a basis for evaluating the hydrologic system at Yucca Mountain independently of analyses based purely on hydraulic arguments. Where more than one conceptual model for flow is possible, based on existing hydraulic data, hydrochemical and isotopic data may be useful in eliminating some of these conceptual models. This report documents the use of geochemical and isotopic data to constrain rates and directions of groundwater flow near Yucca Mountain and the timing and magnitude of recharge in the Yucca Mountain vicinity. The geochemical and isotopic data are also examined with regard to the possible dilution of groundwater recharge from Yucca Mountain by mixing with groundwater downgradient from the potential repository site. Specifically, the primary tasks of this report, as listed in the AMR Development Plan (CRWMS M and O 1999a), consist of the following: (1) Compare geochemical and isotopic data for perched and pore water in the unsaturated zone with similar data from the saturated zone to determine if local recharge is present in the regional groundwater system; (2) Determine the timing of the recharge from stable isotopes such as deuterium ( 2 H) and oxygen-18 ( 18 O), which are known to vary over time as a function of climate, and from radioisotopes such as carbon-14 ( 14 C) and chlorine-36 ( 36 Cl); (3) Determine the magnitude of recharge from relatively

  8. Groundwater flow systems in the great Aletsch glacier region (Valais, Switzerland)

    Science.gov (United States)

    Alpiger, Andrea; Loew, Simon

    2014-05-01

    Groundwater flow systems in Alpine areas are often complex and challenging to investigate due to special topographic and climatic conditions governing groundwater recharge and bedrock flow. Studies seeking to characterize high-alpine groundwater systems remain rare, but are of high interest, e.g. for water supply, hydropower systems, traffic tunnels or rock slope deformation and landslide hazards. The goal of this study is to better understand the current and past groundwater flow systems of the UNESCO World Heritage mountain ridge separating the great Aletsch glacier and the Rhone valley, considering climatic and glacier fluctuations during the Lateglacial and Holocene periods. This ridge is crossed by a hydropower bypass drift (Riederhornstollen) and is composed of fractured crystalline rocks overlain by various types of landslides and glacial deposits. Surface hydrology observations (fracture properties, groundwater seepage, spring lines and physico-chemical parameters) and hydropower drift inflow measurements contributed to the characterization of bedrock hydraulic conductivities and preferential groundwater pathways. Basic conceptual hydrogeological models were tested with observed drift inflows and the occurrence of springs using free-surface, variably saturated, vertical 2D groundwater flow models (using the code SEEP/W from GeoStudio 2007). Already simple two-layer models, representing profile sections orthogonal to the mountain ridge, provided useful results. Simulations show that differences in the occurrence of springs on each side of the mountain ridge are likely caused by the occurrence of glacial till (generating perched groundwater), the deep-seated sagging landslide mass, faults and asymmetric ridge topography, which together force the main groundwater flow direction to be oriented towards the Rhone valley, even from beyond the mountain ridge. Surprisingly, the most important springs (those with high discharge rates) are located at high elevations

  9. Modeling groundwater flow to elliptical lakes and through multi-aquifer elliptical inhomogeneities

    Science.gov (United States)

    Bakker, Mark

    2004-05-01

    Two new analytic element solutions are presented for steady flow problems with elliptical boundaries. The first solution concerns groundwater flow to shallow elliptical lakes with leaky lake beds in a single-aquifer. The second solution concerns groundwater flow through elliptical cylinder inhomogeneities in a multi-aquifer system. Both the transmissivity of each aquifer and the resistance of each leaky layer may differ between the inside and the outside of an inhomogeneity. The elliptical inhomogeneity may be bounded on top by a shallow elliptical lake with a leaky lake bed. Analytic element solutions are obtained for both problems through separation of variables of the Laplace and modified-Helmholtz differential equations in elliptical coordinates. The resulting equations for the discharge potential consist of infinite sums of products of exponentials, trigonometric functions, and modified-Mathieu functions. The series are truncated but still fulfill the differential equation exactly; boundary conditions are met approximately, but up to machine accuracy provided enough terms are used. The head and flow may be computed analytically at any point in the aquifer. Examples are given of uniform flow through an elliptical lake, a well pumping near two elliptical lakes, and uniform flow through three elliptical inhomogeneities in a multi-aquifer system. Mathieu functions may be applied in a similar fashion to solve other groundwater flow problems in semi-confined aquifers and leaky aquifer systems with elliptical internal or external boundaries.

  10. Fractional governing equations of transient groundwater flow in confined aquifers with multi-fractional dimensions in fractional time

    Science.gov (United States)

    Kavvas, M. Levent; Tu, Tongbi; Ercan, Ali; Polsinelli, James

    2017-10-01

    Using fractional calculus, a dimensionally consistent governing equation of transient, saturated groundwater flow in fractional time in a multi-fractional confined aquifer is developed. First, a dimensionally consistent continuity equation for transient saturated groundwater flow in fractional time and in a multi-fractional, multidimensional confined aquifer is developed. For the equation of water flux within a multi-fractional multidimensional confined aquifer, a dimensionally consistent equation is also developed. The governing equation of transient saturated groundwater flow in a multi-fractional, multidimensional confined aquifer in fractional time is then obtained by combining the fractional continuity and water flux equations. To illustrate the capability of the proposed governing equation of groundwater flow in a confined aquifer, a numerical application of the fractional governing equation to a confined aquifer groundwater flow problem was also performed.

  11. Hydrogeochemical analysis and evaluation of groundwater quality ...

    Indian Academy of Sciences (India)

    of the aquatic systems of the Gadilam river basin show that the groundwater is near-acidic to alkaline and mostly oxidizing in nature. Higher concentration of Sodium and Chloride indicates leaching of secondary salts and anthropogenic impact by industry and salt water intrusion. Spatial distribution of EC indicates ...

  12. Principal component analysis of groundwater quality data ...

    African Journals Online (AJOL)

    The physico-chemical quality data of groundwater extracted from 36 boreholes in Ho Municipality indicated that 11 sources recorded pH values outside WHO guideline range, while 5 recorded turbidity levels above WHO guideline limits. Sodium levels ranged from 1.80 to 544 mg/L with a mean of 111 ± 132 mg/l; chloride ...

  13. Groundwater flow and water budget in the surficial and Floridan aquifer systems in east-central Florida

    Science.gov (United States)

    Sepulveda, Nicasio; Tiedeman, Claire; O'Reilly, Andrew M.; Davis, Jeffrey B.; Burger, Patrick

    2012-01-01

    A numerical transient model of the surficial and Floridan aquifer systems in east-central Florida was developed to (1) increase the understanding of water exchanges between the surficial and the Floridan aquifer systems, (2) assess the recharge rates to the surficial aquifer system from infiltration through the unsaturated zone and (3) obtain a simulation tool that could be used by water-resource managers to assess the impact of changes in groundwater withdrawals on spring flows and on the potentiometric surfaces of the hydrogeologic units composing the Floridan aquifer system. The hydrogeology of east-central Florida was evaluated and used to develop and calibrate the groundwater flow model, which simulates the regional fresh groundwater flow system. The U.S. Geological Survey three-dimensional groundwater flow model, MODFLOW-2005, was used to simulate transient groundwater flow in the surficial, intermediate, and Floridan aquifer systems from 1995 to 2006. The East-Central Florida Transient model encompasses an actively simulated area of about 9,000 square miles. Although the model includes surficial processes-rainfall, irrigation, evapotranspiration (ET), runoff, infiltration, lake water levels, and stream water levels and flows-its primary purpose is to characterize and refine the understanding of groundwater flow in the Floridan aquifer system. Model-independent estimates of the partitioning of rainfall into ET, streamflow, and aquifer recharge are provided from a water-budget analysis of the surficial aquifer system. The interaction of the groundwater flow system with the surface environment was simulated using the Green-Ampt infiltration method and the MODFLOW-2005 Unsaturated-Zone Flow, Lake, and Streamflow-Routing Packages. The model is intended to simulate the part of the groundwater system that contains freshwater. The bottom and lateral boundaries of the model were established at the estimated depths where the chloride concentration is 5,000 milligrams

  14. Groundwater flow and hydraulic gradients in fractures and fracture zones at Forsmark and Oskarshamn

    International Nuclear Information System (INIS)

    Nordqvist, Rune; Gustafsson, Erik; Andersson, Peter; Thur, Pernilla

    2008-10-01

    Groundwater flow measurements with the point dilution method have been carried out within various SKB field investigations in Swedish bedrock since the beginning of the 1980's. Knowledge of groundwater flow under natural conditions is an important part of the overall understanding of hydrogeological and hydrochemical conditions at investigated sites and for the function of engineered barriers. Flow measurements have also been made during pumping tests to provide indications of hydraulic connections between various bedrock features. Another frequent use of groundwater flow data from dilution measurements is for identifying suitable injection sections for cross-hole tracer experiments. This report presents an overview of groundwater flow measurements made in boreholes during various SKB investigation programmes. The main purpose is to provide a summary of dilution measurements intended to characterise natural flow conditions within the SKB site investigations at Forsmark and Oskarshamn, and to analyse data on a site basis. In addition, general overviews of earlier investigations at Finnsjoen, Aevroe and Aespoe are presented as well as more recent measurements in connection with cross-hole experiments in Forsmark and Oskarshamn. The measured groundwater flow rates in Forsmark and Oskarshamn are approximately log-normally distributed with a median of about 10 -8 m 3 /s. Flow rates show no systematic depth-dependence, high or low flow rates may occur at any depth. The only exception to this is that there appears to be a tendency for high flow rates in shallow borehole sections at Forsmark. Another main variable that is analysed is the hydraulic gradient, derived from borehole flow rates, a transmissivity estimate and assumptions about the flow convergence due to the borehole. This data shows very large variation from extremely low gradients to in several cases seemingly unrealistically high gradients. Most of the calculated gradients are within the interval of 0

  15. Region-scale groundwater flow modelling of generic high level waste disposal sites

    International Nuclear Information System (INIS)

    Metcalfe, D.

    1996-02-01

    Regional-scale groundwater flow modelling analyses are performed on generic high level waste (HLW) disposal sites to assess the extent to which a large crystalline rock mass such as a pluton or batholith can be expected to contain and isolate HLW in terms of hydraulic considerations, for a variety of geologic and hydrogeologic conditions. The two-dimensional cross-sectional conceptual models of generic HLW disposal sites are evaluated using SWIFT III, which is a finite-difference flow and transport code. All steps leading to the final results and conclusions are incorporated in this report. The available data and information on geological and hydrogeologic conditions in plutons and batholiths are summarized. The generic conceptual models developed from this information are defined in terms of the finite difference grid, the geologic and hydrogeologic properties and the hydrologic boundary conditions used. The modelled results are described with contour maps showing the modelled head fields, groundwater flow paths and travel times and groundwater flux rates within the modelled systems. The results of the modelling analyses are used to develop general conclusions on the scales and patterns of groundwater flow in granitic plutons and batholiths. The conclusions focus on geologic and hydrogeologic characteristics that can result in favourable conditions, in terms of hydraulic considerations, for a HLW repository. (author) 43 refs., 9 tabs., 40 figs

  16. Limitations to upscaling of groundwater flow models dominated by surface water interaction

    NARCIS (Netherlands)

    Vermeulen, P.T.M.; Te Stroet, C.B.M.; Heemink, A.W.

    2006-01-01

    Different upscaling methods for groundwater flow models are investigated. A suite of different upscaling methods is applied to several synthetic cases with structured and unstructured porous media. Although each of the methods applies best to one of the synthetic cases, no performance differences

  17. Solute transport by groundwater flow to wetland ecosystems : the environmental impact of human activities

    NARCIS (Netherlands)

    Schot, P.P.

    1991-01-01

    This thesis deals with solute transport by groundwater flow and the way in which solute transport is affected by human activities. This in relation to wetland ecosystems. Wetlands in the eastern part of the Vecht river plain in The Netherlands are historically renown for their great variety of

  18. 3-D numerical modelling of groundwater flow for scenario-based ...

    African Journals Online (AJOL)

    The data related to piezometric water levels, canal gauges, well logs, meteorological and lithological information were collected from Punjab Irrigation Department (PID), Water and Power Development Authority (WAPDA). Groundwater flow models for both steady and transient conditions were set-up using FEFLOW-3D.

  19. Comparison of groundwater flow in Southern California coastal aquifers

    Science.gov (United States)

    Hanson, Randall T.; Izbicki, John A.; Reichard, Eric G.; Edwards, Brian D.; Land, Michael; Martin, Peter

    2009-01-01

    Development of the coastal aquifer systems of Southern California has resulted in overdraft, changes in streamflow, seawater intrusion, land subsidence, increased vertical flow between aquifers, and a redirection of regional flow toward pumping centers. These water-management challenges can be more effectively addressed by incorporating new understanding of the geologic, hydrologic, and geochemical setting of these aquifers.

  20. Stream flow - its estimation, uncertainty and interaction with groundwater and floodplains

    DEFF Research Database (Denmark)

    Poulsen, Jane Bang

    Stream flow and processes related to its interaction with groundwater and floodplains are important elements of the hydrological cycle and form the basis for a range of scientific, environmental and management applications. Furthermore, stream flow is one of the readily visible components...... of the hydrological cycle and is consequently an obvious marker for the ecological, chemical and hydrological conditions in the stream as well as in adjacent catchments. Therefore, it is crucial that stream flow and processes related to stream flow can be accurately detected, quantified and understood. This thesis...

  1. Analytical Study of Unsteady Nested Groundwater Flow Systems

    Directory of Open Access Journals (Sweden)

    Hong Niu

    2015-01-01

    Full Text Available Two analytical solutions using segregation variable method to calculate the hydraulic head under steady and unsteady flow conditions based on Tóth’s classical model were developed. The impacts of anisotropy ratio, hydraulic conductivity (K, and specific yield (μs on the flow patterns were analyzed. It was found that the area of the equal velocity region increases and the penetrating depth of the flow system decreases at steady state with anisotropy ratio increases, which is defined as ε=Kx/Kz. In addition, stagnant zones can be found in the flow field where the streamlines have opposite directions. These stagnant zones move toward the surface as the horizontal hydraulic conductivity increases. The results of the study on transient flow indicate that a relative increase in hydraulic conductivity produces a positive impact on hydraulic head and a relative enhancement in specific yield produces a negative effect on hydraulic head at early times.

  2. Hydrogeology, groundwater flow, and groundwater quality of an abandoned underground coal-mine aquifer, Elkhorn Area, West Virginia

    Science.gov (United States)

    Kozar, Mark D.; McCoy, Kurt J.; Britton, James Q.; Blake, B.M.

    2017-01-01

    The Pocahontas No. 3 coal seam in southern West Virginia has been extensively mined by underground methods since the 1880’s. An extensive network of abandoned mine entries in the Pocahontas No. 3 has since filled with good-quality water, which is pumped from wells or springs discharging from mine portals (adits), and used as a source of water for public supplies. This report presents results of a three-year investigation of the geology, hydrology, geochemistry, and groundwater flow processes within abandoned underground coal mines used as a source of water for public supply in the Elkhorn area, McDowell County, West Virginia. This study focused on large (> 500 gallon per minute) discharges from the abandoned mines used as public supplies near Elkhorn, West Virginia. Median recharge calculated from base-flow recession of streamflow at Johns Knob Branch and 12 other streamflow gaging stations in McDowell County was 9.1 inches per year. Using drainage area versus mean streamflow relationships from mined and unmined watersheds in McDowell County, the subsurface area along dip of the Pocahontas No. 3 coal-mine aquifer contributing flow to the Turkey Gap mine discharge was determined to be 7.62 square miles (mi2), almost 10 times larger than the 0.81 mi2 surface watershed. Results of this investigation indicate that groundwater flows down dip beneath surface drainage divides from areas up to six miles east in the adjacent Bluestone River watershed. A conceptual model was developed that consisted of a stacked sequence of perched aquifers, controlled by stress-relief and subsidence fractures, overlying a highly permeable abandoned underground coal-mine aquifer, capable of substantial interbasin transfer of water. Groundwater-flow directions are controlled by the dip of the Pocahontas No. 3 coal seam, the geometry of abandoned mine workings, and location of unmined barriers within that seam, rather than surface topography. Seven boreholes were drilled to intersect

  3. Stratabound pathways of preferred groundwater flow: An example from the Copper Ridge Dolomite in East Tennessee

    Energy Technology Data Exchange (ETDEWEB)

    Lee, R.; Ketelle, D.

    1987-07-14

    The Copper Ridge Dolomite of the Upper Cambrian Knox Group underlies a site at Oak Ridge, Tennessee under consideration by the Department of Energy (DOE) for a below ground waste disposal facility. The Copper Ridge was studied for DOE to understand the influence of lithology on deep groundwater flow. Three facies types are distinguished which comprise laterally continuous, 1 to 4 m thick rock units interpreted to represent upward-shallowing depositional cycles having an apparently significant effect on groundwater flow at depth. Rock core observations indicate one of the recurring facies types is characterized by thin to medium-bedded, fine-grained dolostone with planar cryptalgal laminae and thin shaley partings. Distinctive fracturing in this facies type, that may have resulted from regional structural deformation, it considered to be responsible for weathering at depth and the development of stratabound pathways of preferred groundwater flow. In addition, geophysical data suggest that one occurrence of this weathered facies type coincides with an apparent geochemical interface at depth. Geophysical data also indicate the presence of several fluid invasion horizons, traceable outside the study area, which coincide with the unweathered occurrence of this fine-grained facies type. The subcropping of recurrent zones of preferred groundwater flow at the weathered/unweathered interface may define linear traces of enhanced aquifer recharge paralleling geologic strike. Vertical projection of these zones from the weathered/unweathered rock interface to the ground surface may describe areas of enhanced infiltration. Tests to determine the role of stratigraphic controls on groundwater flow are key components of future investigations on West Chestnut Ridge. 14 refs., 13 figs.

  4. Stratabound pathways of preferred groundwater flow: An example from the Copper Ridge Dolomite in East Tennessee

    International Nuclear Information System (INIS)

    Lee, R.; Ketelle, D.

    1987-01-01

    The Copper Ridge Dolomite of the Upper Cambrian Knox Group underlies a site at Oak Ridge, Tennessee under consideration by the Department of Energy (DOE) for a below ground waste disposal facility. The Copper Ridge was studied for DOE to understand the influence of lithology on deep groundwater flow. Three facies types are distinguished which comprise laterally continuous, 1 to 4 m thick rock units interpreted to represent upward-shallowing depositional cycles having an apparently significant effect on groundwater flow at depth. Rock core observations indicate one of the recurring facies types is characterized by thin to medium-bedded, fine-grained dolostone with planar cryptalgal laminae and thin shaley partings. Distinctive fracturing in this facies type, that may have resulted from regional structural deformation, it considered to be responsible for weathering at depth and the development of stratabound pathways of preferred groundwater flow. In addition, geophysical data suggest that one occurrence of this weathered facies type coincides with an apparent geochemical interface at depth. Geophysical data also indicate the presence of several fluid invasion horizons, traceable outside the study area, which coincide with the unweathered occurrence of this fine-grained facies type. The subcropping of recurrent zones of preferred groundwater flow at the weathered/unweathered interface may define linear traces of enhanced aquifer recharge paralleling geologic strike. Vertical projection of these zones from the weathered/unweathered rock interface to the ground surface may describe areas of enhanced infiltration. Tests to determine the role of stratigraphic controls on groundwater flow are key components of future investigations on West Chestnut Ridge. 14 refs., 13 figs

  5. Simulation of groundwater flow and pumping scenarios for 1900–2050 near Mount Pleasant, South Carolina

    Science.gov (United States)

    Fine, Jason M.; Petkewich, Matthew D.; Campbell, Bruce G.

    2017-10-31

    Groundwater withdrawals from the Upper Cretaceous-age Middendorf aquifer in South Carolina have created a large, regional cone of depression in the potentiometric surface of the Middendorf aquifer in Charleston and Berkeley Counties, South Carolina. Groundwater-level declines of as much as 249 feet have been observed in wells over the past 125 years and are a result of groundwater use for public water supply, irrigation, and private industry. To address the concerns of users of the Middendorf aquifer, the U.S. Geological Survey, in cooperation with Mount Pleasant Waterworks (MPW), recalibrated an existing groundwater-flow model to incorporate additional groundwater-use and water-level data since 2008. This recalibration process consisted of a technique of parameter estimation that uses regularized inversion and employs “pilot points” for spatial hydraulic property characterization. The groundwater-flow system of the Coastal Plain physiographic province of South Carolina and parts of Georgia and North Carolina was simulated using the U.S. Geological Survey finite-difference computer code MODFLOW-2000.After the model recalibration, the following six predictive water-management scenarios were created to simulate potential changes in groundwater flow and groundwater-level conditions in the Mount Pleasant, South Carolina, area: Scenario 1—maximize MPW reverse-osmosis plant capacity by increasing groundwater withdrawals from the Middendorf aquifer from 3.9 million gallons per day (Mgal/d), which was the amount withdrawn in 2015, to 8.58 Mgal/d; Scenario 2—same as Scenario 1, but with the addition of a 0.5 Mgal/d supply well in the Middendorf aquifer near Moncks Corner, South Carolina; Scenario 3—same as Scenario 1, but with the addition of a 1.5 Mgal/d supply well in the Middendorf aquifer near Moncks Corner, South Carolina; Scenario 4—maximize MPW well capacity by increasing withdrawals from the Middendorf aquifer from 3.9 Mgal/d (in 2015) to 10.16 Mgal

  6. Linking fault pattern with groundwater flow in crystalline rocks at the Grimsel Test Site (Switzerland)

    Science.gov (United States)

    Schneeberger, Raphael; Berger, Alfons; Mäder, Urs K.; Niklaus Waber, H.; Kober, Florian; Herwegh, Marco

    2017-04-01

    Water flow across crystalline bedrock is of major interest for deep-seated geothermal energy projects as well as for underground disposal of radioactive waste. In crystalline rocks enhanced fluid flow is related to zones of increased permeability, i.e. to fractures that are associated to fault zones. The flow regime around the Grimsel Test Site (GTS, Central Aar massif) was assessed by establishing a 3D fault zone pattern on a local scale in the GTS underground facility (deca-meter scale) and on a regional scale at the surface (km-scale). The study reveals the existence of a dense fault zone network consisting of several km long and few tens of cm to meter wide, sub-vertically oriented major faults that are connected by tens to hundreds of meters long minor bridging faults. This geometrical information was used as input for the generation of a 3D fault zone network model. The faults originate from ductile shear zones that were reactivated as brittle faults under retrograde conditions during exhumation. Embrittlement and associated dilatancy along the faults provide the pathways for today's groundwater flow. Detection of the actual 3D flow paths is, however, challenging since flow seem to be not planar but rather tube-like. Two strategies are applied to constrain the 3D geometry of the flow tubes: (i) Characterization of the groundwater infiltrating into the GTS (location, yield, hydraulic head, and chemical composition) and (ii) stress modelling on the base of the 3D structural model to unravel potential domains of enhanced fluid flow such as fault plane intersections and domains of dilatancy. At the Grimsel Test Site, hydraulic and structural data demonstrate that the groundwater flow is head-driven from the surface towards the GTS located some 450 m below the surface. The residence time of the groundwater in this surface-near section is >60 years as evidenced by absence of detectable tritium. However, hydraulic heads obtained from interval pressure measurements

  7. Analysis of TCE Fate and Transport in Karst Groundwater Systems Using Statistical Mixed Models

    Science.gov (United States)

    Anaya, A. A.; Padilla, I. Y.

    2012-12-01

    Karst groundwater systems are highly productive and provide an important fresh water resource for human development and ecological integrity. Their high productivity is often associated with conduit flow and high matrix permeability. The same characteristics that make these aquifers productive also make them highly vulnerable to contamination and a likely for contaminant exposure. Of particular interest are trichloroethylene, (TCE) and Di-(2-Ethylhexyl) phthalate (DEHP). These chemicals have been identified as potential precursors of pre-term birth, a leading cause of neonatal complications with a significant health and societal cost. Both of these contaminants have been found in the karst groundwater formations in this area of the island. The general objectives of this work are to: (1) develop fundamental knowledge and determine the processes controlling the release, mobility, persistence, and possible pathways of contaminants in karst groundwater systems, and (2) characterize transport processes in conduit and diffusion-dominated flow under base flow and storm flow conditions. The work presented herein focuses on the use of geo-hydro statistical tools to characterize flow and transport processes under different flow regimes, and their application in the analysis of fate and transport of TCE. Multidimensional, laboratory-scale Geo-Hydrobed models (GHM) were used for this purpose. The models consist of stainless-steel tanks containing karstified limestone blocks collected from the karst aquifer formation of northern Puerto Rico. The models integrates a network of sampling wells to monitor flow, pressure, and solute concentrations temporally and spatially. Experimental work entails injecting dissolved CaCl2 tracers and TCE in the upstream boundary of the GHM while monitoring TCE and tracer concentrations spatially and temporally in the limestone under different groundwater flow regimes. Analysis of the temporal and spatial concentration distributions of solutes

  8. Perched groundwater-surface interactions and their consequences in stream flow generation in a semi-arid headwater catchment

    Science.gov (United States)

    Molenat, Jerome; Bouteffeha, Maroua; Raclot, Damien; Bouhlila, Rachida

    2013-04-01

    In semi-arid headwater catchment, it is usually admitted that stream flow comes predominantly from Hortonian overland flow (infiltration excess overland flow). Consequently, subsurface flow processes, and especially perched or shallow groundwater flow, have not been studied extensively. Here we made the assumption that perched groundwater flow could play a significant role in stream flow generation in semi-arid catchment. To test this assumption, we analyzed stream flow time series of a headwater catchment in the Tunisian Cap Bon region and quantified the flow fraction coming from groundwater discharge and that from overland flow. Furthermore, the dynamics of the perched groundwater was analyzed, by focusing on the different perched groundwater-surface interaction processes : diffuse and local infiltration, diffuse exfiltration, and direct groundwater discharge to the stream channel. This work is based on the 2.6 km² Kamech catchment (Tunisia), which belongs to the long term Mediterranean hydrological observatory OMERE (Voltz and Albergel, 2002). Results show that even though Hortonian overland flow was the main hydrological process governing the stream flow generation, groundwater discharge contribution to the stream channel annually accounted for from 10% to 20 % depending on the year. Furthermore, at some periods, rising of groundwater table to the soil surface in bottom land areas provided evidences of the occurrence of saturation excess overland flow processes during some storm events. Reference Voltz , M. and Albergel , J., 2002. OMERE : Observatoire Méditerranéen de l'Environnement Rural et de l'Eau - Impact des actions anthropiques sur les transferts de masse dans les hydrosystèmes méditerranéens ruraux. Proposition d'Observatoire de Recherche en Environnement, Ministère de la Recherche.

  9. Risk-based decision analysis for groundwater operable units

    International Nuclear Information System (INIS)

    Chiaramonte, G.R.

    1995-01-01

    This document proposes a streamlined approach and methodology for performing risk assessment in support of interim remedial measure (IRM) decisions involving the remediation of contaminated groundwater on the Hanford Site. This methodology, referred to as ''risk-based decision analysis,'' also supports the specification of target cleanup volumes and provides a basis for design and operation of the groundwater remedies. The risk-based decision analysis can be completed within a short time frame and concisely documented. The risk-based decision analysis is more versatile than the qualitative risk assessment (QRA), because it not only supports the need for IRMs, but also provides criteria for defining the success of the IRMs and provides the risk-basis for decisions on final remedies. For these reasons, it is proposed that, for groundwater operable units, the risk-based decision analysis should replace the more elaborate, costly, and time-consuming QRA

  10. Review of ground-water flow and transport models in the unsaturated zone

    International Nuclear Information System (INIS)

    Oster, C.A.

    1982-11-01

    Models of partially saturated flow and transport in porous media have application in the analysis of existing as well as future low-level radioactive waste facilities located above the water table. An extensive literature search along with telephone and mail correspondence with recognized leading experts in the field, was conducted to identify computer models suitable for studies of low-level radioactive waste facilities located in the unsaturated zone. Fifty-five existing models were identified as potentially useful. Ten of these models were selected for further examination. This report contains a statement of the ground-water flow-contaminant transport problem, a discussion of those methods used to reduce the physical problem to a computer model, a brief discussion about the data requirements of these models. The procedure used to select the ten codes for further discussion is given, along with a list of these models. Finally, the Appendices contain the data about the fifty-five codes examined. Specifically Appendix D contains the detailed discussion of each of the ten selected codes. Included in each discussion are such items which a potential user requires in determining whether the code is suitable for his applications. Appendix E contains brief summary information about each of the fifty-five codes. Included in the summaries are identification data, authors, pertinent references, and model type

  11. How does natural groundwater flow affect CO2 dissolution in saline aquifers?

    Science.gov (United States)

    Rosenzweig, R.; Michel-Meyer, I.; Tsinober, A.; Shavit, U.

    2017-12-01

    The dissolution of supercritical CO2 in aquifer brine is one of the most important trapping mechanisms in CO2 geological storage. Diffusion-limited dissolution is a very slow process. However, since the CO2-rich water is slightly denser than the CO2-free water, when CO2-free water is overlaid by heavier CO2-rich water, convective instability results in fingers of dense CO2-rich water that propagate downwards, causing CO2-unsaturated water to move upwards. This convection process significantly accelerates the dissolution rate of CO2 into the aquifer water.Most previous works have neglected the effect of natural groundwater flow and assumed it has no effect on the dissolution dynamics. However, it was found that in some of the saline aquifers groundwater flow rate, although small, is not zero. In this research, we study the effect of groundwater flow on dissolution by performing laboratory experiments in a bead pack cell using a mixture of methanol and ethylene-glycol as a CO2 analog while varying the water horizontal flow rate. We find that water horizontal flow decreases the number of fingers, their wavelength and their propagation velocity. When testing high water flow rates, no fingers were developed and the dissolution process was entirely diffusive. The effect of water flow on the dissolution rate did not show a clear picture. When increasing the horizontal flow rate the convective dissolution flux slightly decreased and then increased again. It seems that the combination of density-driven flow, water horizontal flow, mechanical dispersion and molecular diffusion affect the dissolution rate in a complex and non-monotonic manner. These intriguing dynamics should be further studied to understand their effect on dissolution trapping.

  12. Hydrogeochemical evidence supporting models for groundwater flow around Sellafield, U.K

    International Nuclear Information System (INIS)

    Metcalfe, R.; Milodowski, A.E.; Noy, D.J.

    1999-01-01

    Recently, United Kingdom Nirex Limited has investigated a site near Sellafield, north-west England to assess its suitability as the potential location for a deep underground repository for the disposal of intermediate- level, and some low-level, solid radioactive waste. Groundwater flow at the site was simulated using a variety of computer codes, based upon conceptual models of the hydrogeological system. Chemical data for groundwaters aided the development of these conceptual models, and also provided a check upon the computer models' validity. Mineralogical information can be accommodated within the conceptual and theoretical framework. The results of the investigation are presented. (author)

  13. Linking stream flow and groundwater to avian habitat in a desert riparian system.

    Science.gov (United States)

    Merritt, David M; Bateman, Heather L

    2012-10-01

    Increasing human populations have resulted in aggressive water development in arid regions. This development typically results in altered stream flow regimes, reduced annual flow volumes, changes in fluvial disturbance regimes, changes in groundwater levels, and subsequent shifts in ecological patterns and processes. Balancing human demands for water with environmental requirements to maintain functioning ecosystems requires quantitative linkages between water in streams and ecosystem attributes. Streams in the Sonoran Desert provide important habitat for vertebrate species, including resident and migratory birds. Habitat structure, food, and nest-building materials, which are concentrated in riparian areas, are provided directly or indirectly by vegetation. We measured riparian vegetation, groundwater and surface water, habitat structure, and bird occurrence along Cherry Creek, a perennial tributary of the Salt River in central Arizona, USA. The purpose of this work was to develop an integrated model of groundwater-vegetation-habitat structure and bird occurrence by: (1) characterizing structural and provisioning attributes of riparian vegetation through developing a bird habitat index (BHI), (2) validating the utility of our BHI through relating it to measured bird community composition, (3) determining the riparian plant species that best explain the variability in BHI, (4) developing predictive models that link important riparian species to fluvial disturbance and groundwater availability along an arid-land stream, and (5) simulating the effects of changes in flow regime and groundwater levels and determining their consequences for riparian bird communities. Riparian forest and shrubland vegetation cover types were correctly classified in 83% of observations as a function of fluvial disturbance and depth to water table. Groundwater decline and decreased magnitude of fluvial disturbance caused significant shifts in riparian cover types from riparian forest to

  14. Isotope and hydrochemical models for evaluation the water loss by evaporation and groundwater flow of dams

    International Nuclear Information System (INIS)

    Santiago, M.F.; Reboucas, A.C.; Frischkorn, H.

    1986-01-01

    Two different approaches are made: an isotope model, based on the observation of the 180/160 ratio of the water, and an hydrochemical model, using the Cl - concentration, are described and applied to determine the evaporation and groundwater flow rates from or to dams. During a period of three years the dams Pereira de Miranda and Caxitore in Pentecostes - Ceara-Brazil (80 Km west of Fortaleza), located in the Precambrian cristalline rock area, were studies. The results show that the models have a good applicability, to estimate the average daily depth of evaporation from free-water surfaces, from nearby porous media or the groundwater inflow or outflow. (author) [pt

  15. A groundwater-flow model for the Treasure Valley and surrounding area, southwestern Idaho

    Science.gov (United States)

    Bartolino, James R.; Vincent, Sean

    2017-04-17

    The U.S. Geological Survey (USGS), in partnership with the Idaho Department of Water Resources (IDWR) and Idaho Water Resource Board (IWRB), will construct a numerical groundwater-flow model of the Treasure Valley and surrounding area. Resource managers will use the model to simulate potential anthropogenic and climatic effects on groundwater for water-supply planning and management. As part of model construction, the hydrogeologic understanding of the aquifer system will be updated with information collected during the last two decades, as well as new data collected for the study.

  16. Spatial Analysis of Linear Structures in the Exploration of Groundwater

    Directory of Open Access Journals (Sweden)

    Abdramane Dembele

    2017-11-01

    Full Text Available The analysis of linear structures on major geological formations plays a crucial role in resource exploration in the Inner Niger Delta. Highlighting and mapping of the large lithological units were carried out using image fusion, spectral bands (RGB coding, Principal Component Analysis (PCA, and band ratio methods. The automatic extraction method of linear structures has permitted the obtaining of a structural map with 82,659 linear structures, distributed on different stratigraphic stages. The intensity study shows an accentuation in density over 12.52% of the total area, containing 22.02% of the linear structures. The density and nodes (intersections of fractures formed by the linear structures on the different lithologies allowed to observe the behavior of the region’s aquifers in the exploration of subsoil resources. The central density, in relation to the hydrographic network of the lowlands, shows the conditioning of the flow and retention of groundwater in the region, and in-depth fluids. The node areas and high-density linear structures, have shown an ability to have rejections in deep (pores that favor the formation of structural traps for oil resources.

  17. Flow Injection Analysis

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    2004-01-01

    This chapter provides an introduction to automated chemical analysis, which essentially can be divided into two groups: batch assays, where the solution is stationary while the container is moved through a number of stations where various unit operations performed; and continuous-flow procedures,......, but it permits thr execution of novel and unique analytical procedures which are difficult or even impossible by conventional means. The performance and applicability of FIA, SI and LOV are illustrated by a series of practical examples....... FIA is based on the creation of a concentration gradient of the injected sample solution and on reproducible and precise timing of all events, it allows exploitation of a transient read-out. This in turn implies that not only does FIA allow the augmentation of existing analytical techniques...

  18. Groundwater flow and tritium migration from the SRS Old Burial Ground to Fourmile Branch

    International Nuclear Information System (INIS)

    Flach, G.P.; Hamm, L.L.; Harris, M.K.

    1996-04-01

    The objectives of this investigation are twofold. The initial goal is to devise and demonstrate a technique for directly incorporating fine-scale lithologic data into heterogeneous hydraulic conductivity fields, for improved groundwater flow and contaminant transport model accuracy. The ultimate goal is to rigorously simulate past and future tritium migration from the SRS Old Burial Ground towards Fourmile Branch, to better understand the effects of various remediation alternatives such as no action and capping. Large-scale variability in hydraulic conductivity is usually the main influence on field-scale groundwater flow patterns and dispersive transport, following the relative locations of recharge and discharge areas. Incorporating realistic hydraulic conductivity heterogeneity into flow and transport models is paramount to accurate simulations, particularly for contaminant migration. Sediment lithologic descriptions and geophysical logs typically offer finer spatial resolution, and therefore more potential information about heterogeneity, than other site characterization data

  19. Influence of temporally variable groundwater flow conditions on point measurements and contaminant mass flux estimations

    DEFF Research Database (Denmark)

    Rein, Arno; Bauer, S; Dietrich, P

    2009-01-01

    information representing observation wells installed along control planes using different well frequencies and configurations. Results of the scenario simulations show that temporally variable flow conditions can lead to significant temporal fluctuations of the concentration and thus are a substantial source...... is present, the concentration variability due to a fluctuating groundwater flow direction varies significantly within the control plane and between the different realizations. Determination of contaminant mass fluxes is also influenced by the temporal variability of the concentration measurement, especially...... periods of groundwater flow fluctuation. For the determination of mass fluxes at heterogeneous sites, however, local fluxes, which may vary considerably along a control plane, have to be accounted for. Here, dosimeter sampling in combination with time integrated local water flux measurements can improve...

  20. A preliminary evaluation of regional ground-water flow in south-central Washington

    Science.gov (United States)

    La Sala, A. M.; Doty, G.C.; Pearson, F.J.

    1973-01-01

    The characteristics of regional ground-water flow were investigated in a 4,500-square-mile region of south-central Washington, centered on the U.S. Atomic Energy Commission Hanford Reservation. The investigation is part of the Commission's feasibility study on storing high-level radioactive waste in chambers mined in basaltic rocks at a. depth of about 3,000 feet or more below the surface. Ground-water flow., on a regional scale, occurs principally in the basalt and-in interbedded sediments of the Columbia River Group, and is controlled by topography, the structure of the basalt, and the large streams--the Columbia, Snake, and Yakima Rivers. The ground water beneath the main part of the Hanford Reservation, south and west of the Columbia River, inures southeastward from recharge areas in the uplands, including Cold Creek and Dry Creek valleys, and ultimately discharges to the Columbia River south of the reservation: East and southeast of the Columbia River, ground water flows generally southwestward and discharges to the River. The Yakima River valley contains a distinct flow system in which movement is toward the Yakima River from the topographic divides. A large southward-flowing ground-water system beneath the southern flank of the Horse Heaven Hills discharges to the Columbia River in the westward-trending reach downstream from Wallula Gap.

  1. Ground-water discharge and base-flow nitrate loads of nontidal streams, and their relation to a hydrogeomorphic classification of the Chesapeake Bay Watershed, middle Atlantic Coast

    Science.gov (United States)

    Bachman, L. Joseph; Lindsey, Bruce D.; Brakebill, John W.; Powars, David S.

    1998-01-01

    billion gallons of water that reaches the Chesapeake Bay each day, nearly 27 billion gallons is base flow. Generalized lithology (siliciclastic, carbonate, crystalline, and unconsolidated) was combined with physiographic province (the Appalachian Plateau, the Valley and Ridge, the Blue Ridge, the Piedmont, including the Mesozoic Lowland section, and the Coastal Plain) to delineate 11 hydrogeomorphic regions. Areal variation of base flow and base-flow nitrate yield were assessed by means of nonparametric, one-way analysis of variance on basins grouped by the dominant hydrogeomorphic region and by correlation analysis of base flow or base-flow nitrate yield with the percentage of land area of a given hydrogeomorphic region within a basin. Base flow appeared to have a significant relation to the hydrogeomorphic regions. The highest percentages of base flow were found in areas underlain by carbonate rock, crystalline rock with relatively low relief, and unconsolidated sediments. Lower percentages were found in areas underlain by siliclastic rocks and crystalline rocks with relatively high relief. The relation between base-flow nitrate yield and hydrogeomorphic region is less clear. Although there is a relation between low nitrate yields and areas underlain by highrelief siliciclastic rocks, and a relation between high yields and carbonate rocks, much of this relation can be explained by the strong association between the hydrogeomorphic units and land use. In addition, most basins are mixtures of several hydrogeomorphic regions, so the nitrate yield from a basin depends on a large number of complex interacting factors. These unclear results indicate that the sample of available data used here may not be adequate to fully assess the relation between base-flow nitrate yield and the hydrogeomorphic setting of the basin. The results appear to show, however, that ground-water discharge is an important component of the total nontidal streamflow, and that ground

  2. Role of the Analytic Element Method in regional-scale GIS-based modeling of groundwater flow and transport

    Science.gov (United States)

    Jankovic, I.

    2003-12-01

    The basic principle of the Analytic Element Method (AEM) is the superposition: complex regional-scale flows are simulated by adding the influences of individual analytic elements. Each analytic element contains geographic information and mathematical functions that describe its influence on regional groundwater flow. The main AEM advantage, relevant to GIS-based modeling, is a direct correspondence of analytic elements and hydrologic aquifer features (such as lakes, rivers, water-supply wells). The flow solution (water table elevation and fluxes) is created without discretization by including all relevant elements (or features). Several regional-scale groundwater models have been developed using the AEM include NAGROM (the National Groundwater Model of The Netherlands) and the Twin Cities Metropolitan Area Groundwater Model (Metro Model). The one-to-one correspondence of elements to hydrologic features allows for elegant integration of groundwater modeling and GIS software. This simplifies both model development and management. In contrast to finite-difference and finite-element based methods, the AEM does not require any grid-based data; all input data are vector-based. This representational style coincides well with the strengths of Geographic Information Systems. This presentation will focus on both the practical aspects of the AEM relevant to GIS-based modeling and the development of a new GIS-based user interface for AEM modeling. Recent computational advances related to regional-scale modeling using AEM will be discussed and demonstrated. These advances include (1) development of solution algorithms designed for massively parallel supercomputers where the same advantage (one-to-one correspondence of analytic elements and hydrologic features) is responsible for efficient implementation in parallel environments, and (2) algorithm enhancements designed for single-processor machines. Groundwater models with thousands of elements can hence be solved. A public

  3. Modelling the impact of a subsurface barrier on groundwater flow in the lower Palar River basin, southern India

    Science.gov (United States)

    Senthilkumar, M.; Elango, L.

    2011-06-01

    Groundwater modelling is widely used as a management tool to understand the behaviour of aquifer systems under different hydrological stresses, whether induced naturally or by humans. The objective of this study was to assess the effect of a subsurface barrier on groundwater flow in the Palar River basin, Tamil Nadu, southern India. Groundwater is supplied to a nearby nuclear power plant and groundwater also supplies irrigation, industrial and domestic needs. In order to meet the increasing demand for groundwater for the nuclear power station, a subsurface barrier/dam was proposed across Palar River to increase the groundwater heads and to minimise the subsurface discharge of groundwater into the sea. The groundwater model used in this study predicted that groundwater levels would increase by about 0.1-0.3 m extending out a distance of about 1.5-2 km from the upstream side of the barrier, while on the downstream side, the groundwater head would lower by about 0.1-0.2 m. The model also predicted that with the subsurface barrier in place the additional groundwater requirement of approximately 13,600 m3/day (3 million gallons (UK)/day) can be met with minimum decline in regional groundwater head.

  4. Ground-water flow and quality in the Atlantic City 800-foot sand, New Jersey

    Science.gov (United States)

    McAuley, Steven D.; Barringer, Julia L.; Paulachok, Gary N.; Clark, Jeffrey S.; Zapecza, Otto S.

    2001-01-01

    reported for water in a former supply well in southern Cape May County. These data indicate that salty water has moved inland in Cape May County. Analysis of the chloride-concentration data indicates that ground water with a chloride concentration of 250 mg/L is within 4 miles of supply wells in Stone Harbor, Cape May County, and is about 10 miles offshore of supply wells near Atlantic City. Results of numerical simulations of ground-water flow were analyzed to determine the effects of four water-supply alternatives on water levels, the flow budget, and potential saltwater movement toward pumping centers during 1986-2040. In the supply alternatives, pumpage is (1) held constant at 1986 rates of pumpage; (2) increased by 35 percent at 1986 locations; (3) increased by 35 percent, but with relocation of some supply wells further inland; and (4) increased by 35 percent but with some of the increase derived from inland wells tapping the Kirkwood-Cohansey aquifer system rather than the Atlantic City 800-foot sand. Inland relocation of supply wells closer to the updip limit of the overlying confining unit results in the smallest decline in water levels and the smallest rate of ground-water flow between the offshore location of salty water and coastal supply wells. Increased pumpage from coastal supply wells results in the greatest water-level declines and the greatest increase in the rate of ground-water flow from offshore to coastal wells. Flow of undesirable salty ground water from offshore locations remains nearly the same as for current (1986) conditions when pumping rates do not change, and the flow-rate increase is smallest for the relocated pumpage (fourth) alternative. In comparing the two conditions of a 35-percent increase in pumpage, the flow from undesirable salty water positions is lessened and flow from the unconfined aquifer is increased when some of the pumping centers are relocated farther inland. Ground water from the 250-mg/L isochlor position does not reach

  5. Flow pathways in the evolving critical zone - insights from hydraulic groundwater theory

    Science.gov (United States)

    Harman, C. J.; Cosans, C.; Kim, M.

    2017-12-01

    The geochemical signatures of the evolving critical zone are delivered into streams via saturated lateral flow through hillslopes. Here we will draw on hydraulic groundwater theory and scaling arguments to obtain insights into the first-order controls on the transition from vertical infiltration to lateral flow in the critical zone. Hydraulic groundwater theory aims to provide a simplified description of unconfined, saturated groundwater flow in systems that are substantially larger in lateral than vertical extent. The theory rests on the Dupuit assumptions, which are often erroneously stated as including an assumption of exclusively lateral flow. In fact the full three-dimensional flow field can be approximated from these assumptions. Building on this theory, we examine how overall hillslope structure (slope, permeability, convergence/divergence etc.) determines the direction and magnitude of flow in the vicinity of weathering fronts in the critical zone, and how weathering products are delivered to the hillslope base. The results demonstrate that under certain conditions the mere presence of lateral flow will not disturb the lateral symmetry of reaction fronts along the hillslope. Furthermore, coupling to a simple reaction model with porosity/permeability feedback allows us to examine the implications for weathering front advance where saturated lateral flow occurs as a transient perched aquifer at the weathering front. The overall rate of weathering front advance is found to be primarily determined by the component of flow normal to the weathering front, and only significantly accelerated by the lateral component above the weathering front when parent rock permeability is very low.

  6. Simulation of regional ground-water flow in the Upper Deschutes Basin, Oregon

    Science.gov (United States)

    Gannett, Marshall W.; Lite, Kenneth E.

    2004-01-01

    This report describes a numerical model that simulates regional ground-water flow in the upper Deschutes Basin of central Oregon. Ground water and surface water are intimately connected in the upper Deschutes Basin and most of the flow of the Deschutes River is supplied by ground water. Because of this connection, ground-water pumping and reduction of artificial recharge by lining leaking irrigation canals can reduce the amount of ground water discharging to streams and, consequently, streamflow. The model described in this report is intended to help water-management agencies and the public evaluate how the regional ground-water system and streamflow will respond to ground-water pumping, canal lining, drought, and other stresses. Ground-water flow is simulated in the model by the finite-difference method using MODFLOW and MODFLOWP. The finite-difference grid consists of 8 layers, 127 rows, and 87 columns. All major streams and most principal tributaries in the upper Deschutes Basin are included. Ground-water recharge from precipitation was estimated using a daily water-balance approach. Artificial recharge from leaking irrigation canals and on-farm losses was estimated from diversion and delivery records, seepage studies, and crop data. Ground-water pumpage for irrigation and public water supplies, and evapotranspiration are also included in the model. The model was calibrated to mean annual (1993-95) steady-state conditions using parameter-estimation techniques employing nonlinear regression. Fourteen hydraulic-conductivity parameters and two vertical conductance parameters were determined using nonlinear regression. Final parameter values are all within expected ranges. The general shape and slope of the simulated water-table surface and overall hydraulic-head distribution match the geometry determined from field measurements. The fitted standard deviation for hydraulic head is about 76 feet. The general magnitude and distribution of ground-water discharge to

  7. Steady-state numerical groundwater flow model of the Great Basin carbonate and alluvial aquifer system

    Science.gov (United States)

    Brooks, Lynette E.; Masbruch, Melissa D.; Sweetkind, Donald S.; Buto, Susan G.

    2014-01-01

    This report describes the construction, calibration, evaluation, and results of a steady-state numerical groundwater flow model of the Great Basin carbonate and alluvial aquifer system that was developed as part of the U.S. Geological Survey National Water Census Initiative to evaluate the nation’s groundwater availability. The study area spans 110,000 square miles across five states. The numerical model uses MODFLOW-2005, and incorporates and tests complex hydrogeologic and hydrologic elements of a conceptual understanding of an interconnected groundwater system throughout the region, including mountains, basins, consolidated rocks, and basin fill. The level of discretization in this model has not been previously available throughout the study area.

  8. A modified calculation model for groundwater flowing to horizontal ...

    Indian Academy of Sciences (India)

    All these valleys are located in Loess plateau of northern Shaanxi, China. The existing calculation model for single hori- zontal seepage well was built by Wang and Zhang. (2007) based on theory of coupled seepage-pipe flow and equivalent hydraulic conductivity (Chen. 1995; Chen and Lin 1998a, 1998b; Chen and.

  9. Groundwater and contaminant flow modelling in Olomoro area of ...

    African Journals Online (AJOL)

    A conceptual model was developed from the results of the Electrical resistivity survey. The aquifer zones delineated from the Electrical resistivity sounding and the well inventory of the area formed the basis for the flow modelling. The model was simplified into three layers; the top soil, the clayey sand/laterite/clay layer and ...

  10. Determination of filtration velocity and direction of groundwater flow using tracer technique, Port Dickson, Negeri Sembilan

    International Nuclear Information System (INIS)

    Md Shahid Ayub; Roslan Mohd Ali; Kamarudin Samuding

    1996-01-01

    The filtration velocity of the groundwater was determine by introducing I mCi Br-82 into a borehole. Br-82 was in the form of potassium bromide. The result showed that the filtration velocity varies from 2.3 to 4.5 cm/day depending on the soil matrix with the clayey layer posting more resistance to flow. Au-198 in the form of aurium chloride was introduce into two other boreholes to determine the direction of flow. The general trend of flow was in the direction between N140E and N160E

  11. Soil and geologic controls on recharge and groundwater flow response to climate perturbation: A case study of the Yakima River Basin

    Science.gov (United States)

    Nguyen, T. T.; Pham, H. V.; Bachmann, M.; Tague, C.; Adam, J. C.

    2017-12-01

    The Yakima River Basin (YRB) is one of the most important agricultural basins in Washington State with annual revenues in excess of $3.2 billion. This intensively irrigated basin is, however, one of the state's most climatically sensitive water resources system as it heavily relies on winter snowpack and limited reservoir storage. Water shortages and drought are expected to be more frequent with climate change, population growth and increasing agricultural demand. This could result in significant impacts on the groundwater system and subsequently the Yakima River. The goal of this study is to assess how soil and geologic characteristics affect catchment recharge and groundwater flow across three catchments within the YRB using a coupled framework including a physically based hydro-ecological model, the Regional Hydro-Ecologic Simulation System (RHESSys) and a groundwater model, MODFLOW. Soil and geologic-related parameters were randomly sampled to use within the Distributed Evaluation of Local Sensitivity Analysis (DELSA) framework to explore their roles in governing catchment recharge and groundwater flow to climate perturbation. Preliminarily results show that catchment recharge is most sensitive to variation in soil transmissivity in two catchments. However, in the other catchment, recharge is more influenced by soil field capacity and bypass recharge. Recharge is also more sensitive to geologic related parameters in catchments where a portion of its flow comes from deep groundwater. When including the effect of climate perturbations, the sensitivity of recharge responses to soil and geologic characteristics varies with temperature and precipitation change. On the other hand, horizontal hydraulic conductivity is the dominant factor that controls groundwater flow responses in catchments with low permeability soil; alternatively, specific storage (and, to some extent, vertical anisotropy) are important in catchments with more conductive soil. The modeling

  12. Influence of permafrost distribution on groundwater flow in the context of climate-driven permafrost thaw: example from Yukon Flats Basin, Alaska, United States

    Science.gov (United States)

    Walvoord, Michelle Ann; Voss, Clifford I.; Wellman, Tristan P.

    2012-01-01

    Understanding the role of permafrost in controlling groundwater flow paths and fluxes is central in studies aimed at assessing potential climate change impacts on vegetation, species habitat, biogeochemical cycling, and biodiversity. Recent field studies in interior Alaska show evidence of hydrologic changes hypothesized to result from permafrost degradation. This study assesses the hydrologic control exerted by permafrost, elucidates modes of regional groundwater flow for various spatial permafrost patterns, and evaluates potential hydrologic consequences of permafrost degradation. The Yukon Flats Basin (YFB), a large (118,340 km2) subbasin within the Yukon River Basin, provides the basis for this investigation. Model simulations that represent an assumed permafrost thaw sequence reveal the following trends with decreasing permafrost coverage: (1) increased groundwater discharge to rivers, consistent with historical trends in base flow observations in the Yukon River Basin, (2) potential for increased overall groundwater flux, (3) increased spatial extent of groundwater discharge in lowlands, and (4) decreased proportion of suprapermafrost (shallow) groundwater contribution to total base flow. These trends directly affect the chemical composition and residence time of riverine exports, the state of groundwater-influenced lakes and wetlands, seasonal river-ice thickness, and stream temperatures. Presently, the YFB is coarsely mapped as spanning the continuous-discontinuous permafrost transition that model analysis shows to be a critical threshold; thus, the YFB may be on the verge of major hydrologic change should the current permafrost extent decrease. This possibility underscores the need for improved characterization of permafrost and other hydrogeologic information in the region via geophysical techniques, remote sensing, and ground-based observations.

  13. Accurate and efficient calculation of response times for groundwater flow

    Science.gov (United States)

    Carr, Elliot J.; Simpson, Matthew J.

    2018-03-01

    We study measures of the amount of time required for transient flow in heterogeneous porous media to effectively reach steady state, also known as the response time. Here, we develop a new approach that extends the concept of mean action time. Previous applications of the theory of mean action time to estimate the response time use the first two central moments of the probability density function associated with the transition from the initial condition, at t = 0, to the steady state condition that arises in the long time limit, as t → ∞ . This previous approach leads to a computationally convenient estimation of the response time, but the accuracy can be poor. Here, we outline a powerful extension using the first k raw moments, showing how to produce an extremely accurate estimate by making use of asymptotic properties of the cumulative distribution function. Results are validated using an existing laboratory-scale data set describing flow in a homogeneous porous medium. In addition, we demonstrate how the results also apply to flow in heterogeneous porous media. Overall, the new method is: (i) extremely accurate; and (ii) computationally inexpensive. In fact, the computational cost of the new method is orders of magnitude less than the computational effort required to study the response time by solving the transient flow equation. Furthermore, the approach provides a rigorous mathematical connection with the heuristic argument that the response time for flow in a homogeneous porous medium is proportional to L2 / D , where L is a relevant length scale, and D is the aquifer diffusivity. Here, we extend such heuristic arguments by providing a clear mathematical definition of the proportionality constant.

  14. Knowledge, transparency, and refutability in groundwater models, an example from the Death Valley regional groundwater flow system

    Science.gov (United States)

    Hill, Mary C.; Faunt, Claudia C.; Belcher, Wayne; Sweetkind, Donald; Tiedeman, Claire; Kavetski, Dmitri

    2013-01-01

    This work demonstrates how available knowledge can be used to build more transparent and refutable computer models of groundwater systems. The Death Valley regional groundwater flow system, which surrounds a proposed site for a high level nuclear waste repository of the United States of America, and the Nevada National Security Site (NNSS), where nuclear weapons were tested, is used to explore model adequacy, identify parameters important to (and informed by) observations, and identify existing old and potential new observations important to predictions. Model development is pursued using a set of fundamental questions addressed with carefully designed metrics. Critical methods include using a hydrogeologic model, managing model nonlinearity by designing models that are robust while maintaining realism, using error-based weighting to combine disparate types of data, and identifying important and unimportant parameters and observations and optimizing parameter values with computationally frugal schemes. The frugal schemes employed in this study require relatively few (10–1000 s), parallelizable model runs. This is beneficial because models able to approximate the complex site geology defensibly tend to have high computational cost. The issue of model defensibility is particularly important given the contentious political issues involved.

  15. Knowledge, transparency, and refutability in groundwater models, an example from the Death Valley regional groundwater flow system

    Science.gov (United States)

    Hill, Mary C.; Faunt, Claudia C.; Belcher, Wayne R.; Sweetkind, Donald S.; Tiedeman, Claire R.; Kavetski, Dmitri

    This work demonstrates how available knowledge can be used to build more transparent and refutable computer models of groundwater systems. The Death Valley regional groundwater flow system, which surrounds a proposed site for a high level nuclear waste repository of the United States of America, and the Nevada National Security Site (NNSS), where nuclear weapons were tested, is used to explore model adequacy, identify parameters important to (and informed by) observations, and identify existing old and potential new observations important to predictions. Model development is pursued using a set of fundamental questions addressed with carefully designed metrics. Critical methods include using a hydrogeologic model, managing model nonlinearity by designing models that are robust while maintaining realism, using error-based weighting to combine disparate types of data, and identifying important and unimportant parameters and observations and optimizing parameter values with computationally frugal schemes. The frugal schemes employed in this study require relatively few (10-1000 s), parallelizable model runs. This is beneficial because models able to approximate the complex site geology defensibly tend to have high computational cost. The issue of model defensibility is particularly important given the contentious political issues involved.

  16. A General Solution for Groundwater Flow in Estuarine Leaky Aquifer System with Considering Aquifer Anisotropy

    Science.gov (United States)

    Chen, Po-Chia; Chuang, Mo-Hsiung; Tan, Yih-Chi

    2014-05-01

    In recent years the urban and industrial developments near the coastal area are rapid and therefore the associated population grows dramatically. More and more water demand for human activities, agriculture irrigation, and aquaculture relies on heavy pumping in coastal area. The decline of groundwater table may result in the problems of seawater intrusion and/or land subsidence. Since the 1950s, numerous studies focused on the effect of tidal fluctuation on the groundwater flow in the coastal area. Many studies concentrated on the developments of one-dimensional (1D) and two-dimensional (2D) analytical solutions describing the tide-induced head fluctuations. For example, Jacob (1950) derived an analytical solution of 1D groundwater flow in a confined aquifer with a boundary condition subject to sinusoidal oscillation. Jiao and Tang (1999) derived a 1D analytical solution of a leaky confined aquifer by considered a constant groundwater head in the overlying unconfined aquifer. Jeng et al. (2002) studied the tidal propagation in a coupled unconfined and confined costal aquifer system. Sun (1997) presented a 2D solution for groundwater response to tidal loading in an estuary. Tang and Jiao (2001) derived a 2D analytical solution in a leaky confined aquifer system near open tidal water. This study aims at developing a general analytical solution describing the head fluctuations in a 2D estuarine aquifer system consisted of an unconfined aquifer, a confined aquifer, and an aquitard between them. Both the confined and unconfined aquifers are considered to be anisotropic. The predicted head fluctuations from this solution will compare with the simulation results from the MODFLOW program. In addition, the solutions mentioned above will be shown to be special cases of the present solution. Some hypothetical cases regarding the head fluctuation in costal aquifers will be made to investigate the dynamic effects of water table fluctuation, hydrogeological conditions, and

  17. Evaluation of Bias Associated with Capture Maps Derived from Nonlinear Groundwater Flow Models.

    Science.gov (United States)

    Nadler, Cara; Allander, Kip; Pohll, Greg; Morway, Eric; Naranjo, Ramon; Huntington, Justin

    2017-09-21

    The impact of groundwater withdrawal on surface water is a concern of water users and water managers, particularly in the arid western United States. Capture maps are useful tools to spatially assess the impact of groundwater pumping on water sources (e.g., streamflow depletion) and are being used more frequently for conjunctive management of surface water and groundwater. Capture maps have been derived using linear groundwater flow models and rely on the principle of superposition to demonstrate the effects of pumping in various locations on resources of interest. However, nonlinear models are often necessary to simulate head-dependent boundary conditions and unconfined aquifers. Capture maps developed using nonlinear models with the principle of superposition may over- or underestimate capture magnitude and spatial extent. This paper presents new methods for generating capture difference maps, which assess spatial effects of model nonlinearity on capture fraction sensitivity to pumping rate, and for calculating the bias associated with capture maps. The sensitivity of capture map bias to selected parameters related to model design and conceptualization for the arid western United States is explored. This study finds that the simulation of stream continuity, pumping rates, stream incision, well proximity to capture sources, aquifer hydraulic conductivity, and groundwater evapotranspiration extinction depth substantially affect capture map bias. Capture difference maps demonstrate that regions with large capture fraction differences are indicative of greater potential capture map bias. Understanding both spatial and temporal bias in capture maps derived from nonlinear groundwater flow models improves their utility and defensibility as conjunctive-use management tools. © 2017, National Ground Water Association.

  18. Flow and discharge of groundwater from a snowmelt-affected sandy beach

    Science.gov (United States)

    Chaillou, G.; Lemay-Borduas, F.; Larocque, M.; Couturier, M.; Biehler, A.; Tommi-Morin, G.

    2018-02-01

    The study is based on a complex and unique data set of water stable isotopes (i.e., δ18O and δ2H), radon-222 activities (i.e., 222Rn) and groundwater levels to better understand the interaction of fresh groundwater and recirculated seawater in a snowmelt-affected subterranean estuary (STE) in a boreal region (Îles-de-la-Madeleine, Qc, Canada). By using a combination of hydrogeological and marine geochemical approaches, the objective was to analyze and quantify submarine groundwater discharge processes through a boreal beach after the snow melt period, in early June. The distribution of δ18O and δ2H in beach groundwater showed that inland fresh groundwater contributed between 97 and 30% of water masses presented within the STE. A time series of water table levels during the 16 days of the study indicated that tides propagated as a dynamic wave limiting the mass displacement of seawater within the STE. This up-and-down movement of the water table (∼10-30 cm) induced the vertical infiltration of seawater at the falling tide. At the front of the beach, a radon-based mass balance calculated with high-resolution 222Rn survey estimated total SGD of 3.1 m3/m/d at the discharge zone and a mean flow to 1.5 m3/m/d in the bay. The nearshore discharge agreed relatively well with Darcy fluxes calculated at the beach face. Fresh groundwater makes up more than 50% of the total discharge during the measuring campaign. These results indicate that beaches in boreal and cold regions could be important sources of freshwater originate and groundwater-borne solutes and contaminants to the marine environment after the snowmelt.

  19. Constraining recharge and groundwater flow processes in hard-rock aquifers in temperate maritime climate using stable isotope signatures.

    Science.gov (United States)

    Pilatova, Katarina; Ofterdinger, Ulrich

    2015-04-01

    Recharge estimates and in understanding flow process in hard rock aquifers pose significant challenges. These arise from structural complexities of the hardrock aquifers and are further complicated by variability of the superficial cover. A comparative study of three metamorphic catchments situated in the North of Ireland is presented in this study, each with contrasting geology, glaciation history and consequently superficial cover. The presented study focusses on two main strains. Firstly, due to lack of existing records, stable water isotopes in precipitation (δ18O and δ2H) were monitored at the research sites and their temporal and spatial variability was examined. Secondly, flow processes and dynamics of groundwater recharge based on continuous records of stable isotopes in groundwater, collected along catchment transects from various depths, and its variability in relation to the acquired precipitation signal were studied. Each precipitation station exhibited distinct isotopic signatures, where weather effect and proximity to coastline are the main controlling factors governing the isotope signatures. Moreover, in each of the stations the isotopic signature varied seasonally and thus stable isotopes proved a useful tool for assessing the dynamics of groundwater recharge. The analysis of isotope signatures in precipitation and groundwater from various depths within the hard rock aquifers allowed to evaluate the timescale of recharge, with rapid responses varying from few days up to several months. In general, the recharge appeared continuous over the hydrological year within wetter catchments with higher annual precipitation amounts purging the hardrock aquifers throughout the year. However, within comparatively dryer catchments recharge has a more seasonal character, predominantly taking place during the winter half of the year. Spatially, the recharge is highly localised within the elevated catchment areas, where superficial deposits are scarce and the

  20. Geo-Hydro Statistical Characterization of Preferential Flow and Transport Processes in Karst Groundwater Systems

    Science.gov (United States)

    Anaya, A. A.; Padilla, I. Y.; Macchiavelli, R. E.

    2011-12-01

    Karst groundwater systems are highly productive and provide an important fresh water resource for human development and ecological integrity. Their high productivity is often associated with conduit flow and high matrix permeability. The same characteristics that make these aquifers productive also make them highly vulnerable to contamination and a likely for contaminant exposure. Of particular interest are chlorinated organic contaminants and phthalates derived from industrial solvents and plastic by-products. These chemicals have been identified as potential precursors of pre-term birth, a leading cause of neonatal complications with a significant health and societal cost. The general objectives of this work are to: (1) develop fundamental knowledge and determine the processes controlling the release, mobility, persistence, and possible pathways of contaminants in karst groundwater systems, and (2) characterize transport processes in conduit and diffusion-dominated flow under base flow and storm flow conditions. The work presented herein focuses on the development of geo-hydro statistical tools to characterize flow and transport processes under different flow regimes. Multidimensional, laboratory-scale Geo-Hydrobed models were developed and tested for this purpose. The models consist of stainless-steel tanks containing karstified limestone blocks collected from the karst aquifer formation of northern Puerto Rico. The models a network of sampling wells to monitor flow, pressure, and solute concentrations temporally and spatially. Experimental work entailed making a series of point injections in wells while monitoring the hydraulic response in other wells. Statistical mixed models were applied to spatial probabilities of hydraulic response and weighted injected volume data, and were used to determinate the best spatial correlation structure to represent paths of preferential flow in the limestone units under different groundwater flow regimes. Preliminary testing

  1. Patterns of groundwater flow, pH, and electrical conductance in the Nordic west arm tailings, Elliot Lake, Ontario

    International Nuclear Information System (INIS)

    Blackport, R.

    1980-01-01

    The prime objective of the field investigation reported was to install a groundwater monitoring network in and below the west arm Nordic tailings in order to determine the general directions of groundwater flow within the tailings, provide a basis for calculation of the groundwater flux into and out of the tailings, and provide a groundwater sampling network. Areas of upward, downward, and horizontal flow were found. In some areas seepage from the tailings enters the sand aquifer beneath the tailings, and in other areas the seepage enters the permeable bedrock. The chemical composition of pore water in the tailings is variable, in some places highly acidic. The general trends in hydraulic head and gradient were delineated, but it was not possible to define groundwater flow paths within and beneath the tailings, or to carry out mass balance studies

  2. A generalised groundwater flow equation using the concept of non ...

    African Journals Online (AJOL)

    2006-01-01

    Jan 1, 2006 ... K the hydraulic conductivity tensor of the aquifer. Ф(x,t) the piezometric head f(x,t) the strength of any sources or sinks, with x and t the usual spatial and time coordinates. V the gradient operator. ∂t the time derivative. This model showed that the dominant flow field in these aquifers is vertical and linear and ...

  3. The use of natural isotopes for identifying the origins of groundwater flows: Drentsche Aa Brook Valley, The Netherlands.

    Science.gov (United States)

    Elshehawi, Samer; Grootjans, Ab; Bregman, Enno

    2017-04-01

    This paper investigates the origin of various groundwater flows in a small brook valley reserve Drentsche Aa Valley in the northern part of the Netherlands. The aim was also to validate a hydrological model that simulated coupled particle flow in this area and also incorporated different scenarios for groundwater abstraction in order to predict future implications of groundwater abstraction on ecological values. Water samples from various sites and depths were analysed for macro-ionic composition, stable isotopes (2H and 18O) and also 14C. Three sites have 14C activities over 100%, indicating very recent water. The main groundwater discharge areas showed inflow of old groundwater up to 5000 years. Inflow of different groundwater flows of various ages could be detected most clearly from the 14C data. Downstream area that were affected by groundwater abstraction showed distinct infiltration characteristics, both in macro-ionic composition and contents of natural isotopes, to a depth of 6m below surface In the main exfiltration areas, we found that at 95 meters below the surface, the groundwater was characterized by a NaCl type groundwater facies. But the absolute concentrations were not high enough to conclude that double diffusive convection (DDC) near a salt diapir was responsible for this effect.

  4. Groundwater flow analyses in preliminary site investigations. Modelling strategy and computer codes

    International Nuclear Information System (INIS)

    Taivassalo, V.; Koskinen, L.; Meling, K.

    1994-02-01

    The analyses of groundwater flow comprised a part of the preliminary site investigations which were carried out by Teollisuuden Voima Oy (TVO) for five areas in Finland during 1987 -1992. The main objective of the flow analyses was to characterize groundwater flow at the sites. The flow simulations were also used to identify and study uncertainties and inadequacies which are inherent in the results of earlier modelling phases. The flow analyses were performed for flow conditions similar to the present conditions. The modelling approach was based on the concept of an equivalent continuum. Each fracture zone and the rock matrix among the zones was, however, considered separately as a hydrogeologic unit. The numerical calculations were carried out with a computer code package, FEFLOW. The code is based upon the finite element method. With the code two- and one-dimensional elements can also be used by way of embedding them in a three-dimensional element mesh. A set of new algorithms was developed and employed to create element meshes for FEFLOW. The most useful program in the preliminary site investigations was PAAWI, which adds two-dimensional elements for fracture zones to an existing three-dimensional element mesh. The new algorithms reduced significantly the time required to create spatial discretization for complex geometries. Three element meshes were created for each site. The boundaries of the regional models coincide with those of the flow models. (55 refs., 40 figs., 1 tab.)

  5. Simulation of groundwater flow in the glacial aquifer system of northeastern Wisconsin with variable model complexity

    Science.gov (United States)

    Juckem, Paul F.; Clark, Brian R.; Feinstein, Daniel T.

    2017-05-04

    The U.S. Geological Survey, National Water-Quality Assessment seeks to map estimated intrinsic susceptibility of the glacial aquifer system of the conterminous United States. Improved understanding of the hydrogeologic characteristics that explain spatial patterns of intrinsic susceptibility, commonly inferred from estimates of groundwater age distributions, is sought so that methods used for the estimation process are properly equipped. An important step beyond identifying relevant hydrogeologic datasets, such as glacial geology maps, is to evaluate how incorporation of these resources into process-based models using differing levels of detail could affect resulting simulations of groundwater age distributions and, thus, estimates of intrinsic susceptibility.This report describes the construction and calibration of three groundwater-flow models of northeastern Wisconsin that were developed with differing levels of complexity to provide a framework for subsequent evaluations of the effects of process-based model complexity on estimations of groundwater age distributions for withdrawal wells and streams. Preliminary assessments, which focused on the effects of model complexity on simulated water levels and base flows in the glacial aquifer system, illustrate that simulation of vertical gradients using multiple model layers improves simulated heads more in low-permeability units than in high-permeability units. Moreover, simulation of heterogeneous hydraulic conductivity fields in coarse-grained and some fine-grained glacial materials produced a larger improvement in simulated water levels in the glacial aquifer system compared with simulation of uniform hydraulic conductivity within zones. The relation between base flows and model complexity was less clear; however, the relation generally seemed to follow a similar pattern as water levels. Although increased model complexity resulted in improved calibrations, future application of the models using simulated particle

  6. NRC experiences in hydrocoin: An international project for studying ground-water flow modeling strategies

    International Nuclear Information System (INIS)

    Nicholson, T.J.; McCartin, T.J.; Davis, P.A.; Beyeler, W.

    1987-01-01

    The ''Hydrologic Code Intercomparison Study'' (HYDROCOIN) is an international study designed to investigate various ground-water modeling strategies used to analyze the performance of high-level waste disposal sites. The various ground-water models considered are to be used for safety assessments of low- and high-level radioactive waste facilities. The work completed to date has been simulations of test cases developed to verify and validate the numerical codes chosen by the individual project teams. Twenty-five computer codes were tested during the verification phase of the HYDROCOIN effort. To test the codes, seven cases, which include both saturated and unsaturated conditions in both fractured and porous media, were simulated. Simulation results from the 22 international project teams were then intercompared as well as compared to analytical solutions wherever possible. Current work deals with validation of ground-water flow models. After an exhaustive background study, it was determined that validation of complex ground-water flow models based upon a comprehensive data base is presently not possible. Therefore, the test cases accepted for the validation phase are for relatively simple ground-water flow systems where comparison of the simulation results are with limited field or laboratory data. Additionally, work dealing with uncertainty and sensitivity analyses has recently begun. This work explores appropriate ways of using hydrogeologic models in performance assessment by examining uncertainties in the conceptual models and the hydrogeologic parameters. Valuable lessons have been learned from the HYDROCOIN experiences in understanding limitations of the models, available data sets, and modeling strategies

  7. Simulation of groundwater flow in the shallow aquifer system of the Delmarva Peninsula, Maryland and Delaware

    Science.gov (United States)

    Sanford, Ward E.; Pope, Jason P.; Selnick, David L.; Stumvoll, Ryan F.

    2012-01-01

    Estimating future loadings of nitrogen to the Chesapeake Bay requires knowledge about the groundwater flow system and the traveltime of water and chemicals between recharge at the water table and the discharge to streams and directly to the bay. The Delmarva Peninsula has a relatively large proportion of its land devoted to agriculture and a large associated nitrogen load in groundwater that has the potential to enter the bay in discharging groundwater. To better understand the shallow aquifer system with respect to this loading and the traveltime to the bay, the U.S. Geological Survey constructed a steady-state groundwater flow model for the region. The model is based on estimates of recharge calculated using recently developed regression equations for evapotranspiration and surface runoff. The hydrogeologic framework incorporated into the model includes unconfined surficial aquifer sediments, as well as subcropping confined aquifers and confining beds down to 300 feet below land surface. The model was calibrated using 48 water-level measurements and 24 tracer-based ages from wells located across the peninsula. The resulting steady-state flow solution was used to estimate ages of water in the shallow aquifer system through the peninsula and the distribution and magnitude of groundwater traveltime from recharge at the water table to discharge in surface-water bodies (referred to as return time). Return times vary but are typically less than 10 years near local streams and greater than 100 years near the stream divides. The model can be used to calculate nitrate transport parameters in various local watersheds and predict future trends in nitrate loadings to Chesapeake Bay for different future nitrogen application scenarios.

  8. Hydrodynamic analysis application of contaminated groundwater remediation to oil hydrocarbons

    Directory of Open Access Journals (Sweden)

    Pajić Predrag R.

    2017-01-01

    Full Text Available In this paper, the application of the hydrodynamic analysis in the selected ‘pumping and treatment’ remediation method of groundwater hydrocarbon pollution in the case of the Pancevo oil refinery is examined. The applied hydrodynamic analysis represents a regular and necessary approach in modern hydrogeology. Previous chemical analysis of soil and groundwater samples at observation objects revealed their pollution by oil products. New researches included the constraction of 12 piezometric boreholes of varying depths, geoelectric soil sounding, ‘in situ’ measurement of the present contaminant, detected as a hydrophobic phase of LNAPL, chemical analysis of soil and groundwater samples with emphasis on total petroleum hydrocarbons (TPH content, total fats and mineral oils, mercury cations and other characteristic compounds, etc. These researches define the volume of contamination issued by the ‘light’ (LNAPL contamination phase. The selected remediation method for this type of pollution is the ‘Pump and Treat’ method, which implies the pumping of contaminated groundwater from aquifer and their subsequent treatment. A hydrodynamic method was used to select the optimal hydrotechnical solution for LNAPL extraction. On the mathematical model, the prediction calculations for two variant solutions were carried out (‘hydraulic isolation’ and complex for the application of groundwater contamination remediation characterized as front pollution substance (by extraction and injection wells or infiltration pool. By extraction wells performing, it would be possible to remove the LNAPL from the surface of the water with special pumps-skimmers. The importance of the hydrodynamic method application is, in addition to the hydrotechnical solution selection for the LNAPL drainage, the provision of quality basis for the dimensioning of these objects based on the results of the groundwater balance.

  9. Field continuous measurement of dissolved gases with a CF-MIMS: Applications to the physics and biogeochemistry of groundwater flow

    Science.gov (United States)

    Chatton, Eliot; Labasque, Thierry; de La Bernardie, Jérôme; Guihéneuf, Nicolas; Bour, Olivier; Aquilina, Luc

    2017-04-01

    In the perspective of a temporal and spatial exploration of aquatic environments (surface and ground water), we developed a technique for precise field continuous measurements of dissolved gases (N2, O2, CO2, CH4, N2O, H2, He, Ne, Ar, Kr, Xe). With a large resolution (from 1×10-9 to 1×10-2 ccSTP/g) and a capability of high frequency analysis (1 measure every 2 seconds), the CF-MIMS (Continuous Flow Membrane Inlet Mass Spectrometer) is an innovative tool allowing the investigation of a large panel of hydrological and biogeochemical processes in aquatic systems. Based on the available MIMS technology, this study introduces the development of the CF-MIMS (conception for field experiments, membrane choices, ionisation) and an original calibration procedure allowing the quantification of mass spectral overlaps and temperature effects on membrane permeability. This study also presents two field applications of the CF-MIMS (Chatton et al, 2016) involving the well-logging of dissolved gases and the implementation of groundwater tracer tests with dissolved 4He. The results demonstrate the analytical capabilities of the CF-MIMS in the field. Therefore, the CF-MIMS is a valuable tool for the field characterisation of biogeochemical reactivity, aquifer transport properties, groundwater recharge, groundwater residence time and aquifer-river exchanges from few hours to several weeks experiments. Eliot Chatton, Thierry Labasque, Jérôme de La Bernardie, Nicolas Guihéneuf, Olivier Bour and Luc Aquilina; Field Continuous Measurement of Dissolved Gases with a CF-MIMS: Applications to the Physics and Biogeochemistry of Groundwater Flow; Environmental Science & Technology, in press, 2016.

  10. Analysis on the characteristics of parameters in groundwater table fluctuation model for predicting groundwater levels in Hancheon watershed, South Korea

    Science.gov (United States)

    Kim, Nam Won; Kim, Youn Jung; Chung, Il-Moon; Lee, Jeongwoo

    2014-05-01

    A novel application of groundwater table fluctuation method is suggested to predict groundwater level by means of groundwater table variation due to recharge and discharge under unsteady condition. This model analyzes transient groundwater characteristics by using reaction factor related with groundwater flow and specific yield related with recharge. The groundwater level varies according to the characteristics and composite materials of aquifer. In this study, specific yield and reaction factor which are the major two hydrogeological parameters in the WTF(Water Table Fluctuation) method were estimated and analyzed their spatial characteristics. 8 groundwater level stations which have enough measuring period and high correlation with rainfall in the Hancheon watershed were used. The results showed that specific yield was randomly distributed and reaction factor showed inverse trend with altitude. If the enough data were collected, reaction factor according to altitude in ungauged points could be estimated by using these parameter characteristics. keywords: Key words : Groundwater level, parameters, reaction factor, specific yield Acknowledgements This research was supported by the Regional Innovative Technology Project 2B from KICTTEP.

  11. Simulation of groundwater and surface-water flow in the upper Deschutes Basin, Oregon

    Science.gov (United States)

    Gannett, Marshall W.; Lite, Kenneth E.; Risley, John C.; Pischel, Esther M.; La Marche, Jonathan L.

    2017-10-20

    This report describes a hydrologic model for the upper Deschutes Basin in central Oregon developed using the U.S. Geological Survey (USGS) integrated Groundwater and Surface-Water Flow model (GSFLOW). The upper Deschutes Basin, which drains much of the eastern side of the Cascade Range in Oregon, is underlain by large areas of permeable volcanic rock. That permeability, in combination with the large annual precipitation at high elevations, results in a substantial regional aquifer system and a stream system that is heavily groundwater dominated.The upper Deschutes Basin is also an area of expanding population and increasing water demand for public supply and agriculture. Surface water was largely developed for agricultural use by the mid-20th century, and is closed to additional appropriations. Consequently, water users look to groundwater to satisfy the growing demand. The well‑documented connection between groundwater and the stream system, and the institutional and legal restrictions on streamflow depletion by wells, resulted in the Oregon Water Resources Department (OWRD) instituting a process whereby additional groundwater pumping can be permitted only if the effects to streams are mitigated, for example, by reducing permitted surface-water diversions. Implementing such a program requires understanding of the spatial and temporal distribution of effects to streams from groundwater pumping. A groundwater model developed in the early 2000s by the USGS and OWRD has been used to provide insights into the distribution of streamflow depletion by wells, but lacks spatial resolution in sensitive headwaters and spring areas.The integrated model developed for this project, based largely on the earlier model, has a much finer grid spacing allowing resolution of sensitive headwater streams and important spring areas, and simulates a more complete set of surface processes as well as runoff and groundwater flow. In addition, the integrated model includes improved

  12. Groundwater flow modelling under ice sheet conditions in Greenland (phase II)

    Energy Technology Data Exchange (ETDEWEB)

    Jaquet, Olivier; Namar, Rabah; Siegel, Pascal [In2Earth Modelling Ltd, Lausanne (Switzerland); Jansson, Peter [Dept. of Physical Geography and Quaternary Geology, Stockholm Univ., Stockholm (Sweden)

    2012-11-15

    Within the framework of the GAP project, this second phase of geosphere modelling has enabled the development of an improved regional model that has led to a better representation of groundwater flow conditions likely to occur under ice sheet conditions. New data in relation to talik geometry and elevation, as well as to deformation zones were integrated in the geosphere model. In addition, more realistic hydraulic properties were considered for geosphere modelling; they were taken from the Laxemar site in Sweden. The geological medium with conductive deformation zones was modelled as a 3D continuum with stochastically hydraulic properties. Surface and basal glacial meltwater rates provided by a dynamic ice sheet model were assimilated into the groundwater flow model using mixed boundary conditions. The groundwater flow system is considered to be governed by infiltration of glacial meltwater in heterogeneous faulted crystalline rocks in the presence of permafrost and taliks. The characterisation of the permafrost-depth distribution was achieved using a coupled description of flow and heat transfer under steady state conditions. Using glaciological concepts and satellite data, an improved stochastic model was developed for the description at regional scale for the subglacial permafrost distribution in correlation with ice velocity and bed elevation data. Finally, the production of glacial meltwater by the ice sheet was traced for the determination of its depth and lateral extent. The major improvements are related to the type and handling of the subglacial boundary conditions. The use of meltwater rates provided by an ice sheet model applied as input to a mixed boundary condition enables to produce a more plausible flow field in the Eastern part of the domain, in comparison to previous modelling results (Jaquet et al. 2010). In addition, the integration of all potential taliks within the modelled domain provides a better characterisation of the likely groundwater

  13. Groundwater flow modelling under ice sheet conditions in Greenland (phase II)

    International Nuclear Information System (INIS)

    Jaquet, Olivier; Namar, Rabah; Siegel, Pascal; Jansson, Peter

    2012-11-01

    Within the framework of the GAP project, this second phase of geosphere modelling has enabled the development of an improved regional model that has led to a better representation of groundwater flow conditions likely to occur under ice sheet conditions. New data in relation to talik geometry and elevation, as well as to deformation zones were integrated in the geosphere model. In addition, more realistic hydraulic properties were considered for geosphere modelling; they were taken from the Laxemar site in Sweden. The geological medium with conductive deformation zones was modelled as a 3D continuum with stochastically hydraulic properties. Surface and basal glacial meltwater rates provided by a dynamic ice sheet model were assimilated into the groundwater flow model using mixed boundary conditions. The groundwater flow system is considered to be governed by infiltration of glacial meltwater in heterogeneous faulted crystalline rocks in the presence of permafrost and taliks. The characterisation of the permafrost-depth distribution was achieved using a coupled description of flow and heat transfer under steady state conditions. Using glaciological concepts and satellite data, an improved stochastic model was developed for the description at regional scale for the subglacial permafrost distribution in correlation with ice velocity and bed elevation data. Finally, the production of glacial meltwater by the ice sheet was traced for the determination of its depth and lateral extent. The major improvements are related to the type and handling of the subglacial boundary conditions. The use of meltwater rates provided by an ice sheet model applied as input to a mixed boundary condition enables to produce a more plausible flow field in the Eastern part of the domain, in comparison to previous modelling results (Jaquet et al. 2010). In addition, the integration of all potential taliks within the modelled domain provides a better characterisation of the likely groundwater

  14. Influence of faults on groundwater flow and transport at Yucca Mountain, Nevada

    International Nuclear Information System (INIS)

    Cohen, Andrew J.B.; Sitar, Nicholas

    1999-01-01

    Numerical simulations of groundwater flow at Yucca Mountain, Nevada are used to investigate how faults influence groundwater flow pathways and regional-scale macrodispersion. The 3-D model has a unique grid block discretization that facilitates the accurate representation of the complex geologic structure present in faulted formations. Each hydrogeologic layer is discretized into a single layer of irregular and dipping grid blocks, and faults are discretized such that they are laterally continuous and varied in displacement varies along strike. In addition, the presence of altered fault zones is explicitly modeled, as appropriate. Simulations show that upward head gradients can be readily explained by the geometry of hydrogeologic layers, the variability of layer permeabilities, and the presence of permeable fault zones or faults with displacement only, not necessarily by upwelling from a deep aquifer. Large-scale macrodispersion results from the vertical and lateral diversion of flow near the contact of high- and low-permeability layers at faults, and from upward flow within high-permeability fault zones. Conversely, large-scale channeling can occur as a result of groundwater flow into areas with minimal fault displacement. Contaminants originating at the water table can flow in a direction significantly different from that of the water table gradient, and isolated zones of contaminants can occur at the water table downgradient. By conducting both 2-D and 3-D simulations, we show that the 2-D cross-sectional models traditionally used to examine flow in faulted formations may not be appropriate. In addition, the influence of a particular type of fault cannot be generalized; depending on the location where contaminants enter the saturated zone, faults may either enhance or inhibit vertical dispersion

  15. Water and rock geochemistry, geologic cross sections, geochemical modeling, and groundwater flow modeling for identifying the source of groundwater to Montezuma Well, a natural spring in central Arizona

    Science.gov (United States)

    Johnson, Raymond H.; DeWitt, Ed; Wirt, Laurie; Arnold, L. Rick; Horton, John D.

    2011-01-01

    The National Park Service (NPS) seeks additional information to better understand the source(s) of groundwater and associated groundwater flow paths to Montezuma Well in Montezuma Castle National Monument, central Arizona. The source of water to Montezuma Well, a flowing sinkhole in a desert setting, is poorly understood. Water emerges from the middle limestone facies of the lacustrine Verde Formation, but the precise origin of the water and its travel path are largely unknown. Some have proposed artesian flow to Montezuma Well through the Supai Formation, which is exposed along the eastern margin of the Verde Valley and underlies the Verde Formation. The groundwater recharge zone likely lies above the floor of the Verde Valley somewhere to the north or east of Montezuma Well, where precipitation is more abundant. Additional data from groundwater, surface water, and bedrock geology are required for Montezuma Well and the surrounding region to test the current conceptual ideas, to provide new details on the groundwater flow in the area, and to assist in future management decisions. The results of this research will provide information for long-term water resource management and the protection of water rights.

  16. A scalable approach to modeling groundwater flow on massively parallel computers

    International Nuclear Information System (INIS)

    Ashby, S.F.; Falgout, R.D.; Tompson, A.F.B.

    1995-12-01

    We describe a fully scalable approach to the simulation of groundwater flow on a hierarchy of computing platforms, ranging from workstations to massively parallel computers. Specifically, we advocate the use of scalable conceptual models in which the subsurface model is defined independently of the computational grid on which the simulation takes place. We also describe a scalable multigrid algorithm for computing the groundwater flow velocities. We axe thus able to leverage both the engineer's time spent developing the conceptual model and the computing resources used in the numerical simulation. We have successfully employed this approach at the LLNL site, where we have run simulations ranging in size from just a few thousand spatial zones (on workstations) to more than eight million spatial zones (on the CRAY T3D)-all using the same conceptual model

  17. POTENTIAL EFFECTS OF FAULTS ON GROUNDWATER FLOW FOR THE YUCCA FLAT BASIN, NEVADA TEST SITE, NEVADA

    Science.gov (United States)

    Dickerson, R. P.; Fryer, W.

    2009-12-01

    The permeability changes resulting from finely comminuted material in fault cores and the fractured and brecciated rock in fault damage zones allows faults to channelize groundwater flow along the plane of the fault. The efficiency of faults as permeability structures depends on fault zone width, fault offset, depth at which the fault developed, type of faulted rock, extent of secondary mineralization, and fault orientation within current stress field. Studies of faulted volcanic rocks at Yucca Mountain, Nevada, indicate that fault zone width and brecciation increase with fault offset, that faulted welded tuff is more permeable than nonwelded or bedded tuff, and that non-hydrothermal secondary mineralization commonly diminishes fracture permeability. These results are applied to the groundwater conceptual flow model for Yucca Flat (YF) on the Nevada Test Site (NTS). Yucca Flat contains Tertiary volcanic rocks similar to thoise at Yucca Mountain deposited on Paleozoic carbonate rocks whose thickness is increased by local thrust-faults. The YF basin contains north-striking normal faults and is bordered by southwest-striking strike-slip faults to the south and east. Fault permeability values derived from faulted volcanic rocks at Yucca Mountain suggests that major normal faults in Yucca Flat potentially manifest permeability values along the fault plane equal to the highest values determined for volcanic aquifers. Numerous minor faults not assigned specific permeability values are assumed to imbue the basin with a hydraulic anisotropy favoring fault-parallel flow. In this scenario groundwater flows generally from north to south in the Yucca Flat basin, even as the head gradient is primarily towards the centrally located Yucca Fault, which acts as the main subsurface drainage feature within the basin. Studies show that the regional stress field has rotated clockwise such that southwest-striking strike-slip faults are currently under tension. In this scenario these

  18. Computer modeling of ground-water flow at the Savannah River Plant

    International Nuclear Information System (INIS)

    Root, R.W. Jr.

    1979-01-01

    Mathematical equations describing ground-water flow are used in a computer model being developed to predict the space-time distribution of hydraulic head beneath a part of the Savannah River Plant site. These equations are solved by a three-dimensional finite-difference scheme. Preliminary calibration of the hydraulic head model has been completed and calculated results compare well with water-level changes observed in the field. 10 figures, 1 table

  19. Scale problems in assessment of hydrogeological parameters of groundwater flow models

    OpenAIRE

    Nawalany Marek; Sinicyn Grzegorz

    2015-01-01

    An overview is presented of scale problems in groundwater flow, with emphasis on upscaling of hydraulic conductivity, being a brief summary of the conventional upscaling approach with some attention paid to recently emerged approach- es. The focus is on essential aspects which may be an advantage in comparison to the occasionally extremely extensive summaries presented in the literature. In the present paper the concept of scale is introduced as an indispensable part of system ana...

  20. Limitations to upscaling of groundwater flow models dominated by surface water interaction

    OpenAIRE

    Vermeulen, P.T.M.; Te Stroet, C.B.M.; Heemink, A.W.

    2006-01-01

    Different upscaling methods for groundwater flow models are investigated. A suite of different upscaling methods is applied to several synthetic cases with structured and unstructured porous media. Although each of the methods applies best to one of the synthetic cases, no performance differences are formed if the methods were applied to a real three-dimensional case. Furthermore, we focus on boundary conditions, such as Dirichlet, Neumann, and Cauchy conditions, that characterize the interac...

  1. Experimental and numerical modelling of surface water-groundwater flow and pollution interactions under tidal forcing

    Science.gov (United States)

    Spanoudaki, Katerina; Bockelmann-Evans, Bettina; Schaefer, Florian; Kampanis, Nikolaos; Nanou-Giannarou, Aikaterini; Stamou, Anastasios; Falconer, Roger

    2015-04-01

    Surface water and groundwater are integral components of the hydrologic continuum and the interaction between them affects both their quantity and quality. However, surface water and groundwater are often considered as two separate systems and are analysed independently. This separation is partly due to the different time scales, which apply in surface water and groundwater flows and partly due to the difficulties in measuring and modelling their interactions (Winter et al., 1998). Coastal areas in particular are a difficult hydrologic environment to represent with a mathematical model due to the large number of contributing hydrologic processes. Accurate prediction of interactions between coastal waters, groundwater and neighbouring wetlands, for example, requires the use of integrated surface water-groundwater models. In the past few decades a large number of mathematical models and field methods have been developed in order to quantify the interaction between groundwater and hydraulically connected surface water bodies. Field studies may provide the best data (Hughes, 1995) but are usually expensive and involve too many parameters. In addition, the interpretation of field measurements and linking with modelling tools often proves to be difficult. In contrast, experimental studies are less expensive and provide controlled data. However, experimental studies of surface water-groundwater interaction are less frequently encountered in the literature than filed studies (e.g. Ebrahimi et al., 2007; Kuan et al., 2012; Sparks et al., 2013). To this end, an experimental model has been constructed at the Hyder Hydraulics Laboratory at Cardiff University to enable measurements to be made of groundwater transport through a sand embankment between a tidal water body such as an estuary and a non-tidal water body such as a wetland. The transport behaviour of a conservative tracer was studied for a constant water level on the wetland side of the embankment, while running a

  2. The hydraulic conductivity field and groundwater flow in the unconfined aquifer system of the Keta Strip, Ghana

    Science.gov (United States)

    Yidana, Sandow Mark; Chegbeleh, Larry Pax

    2013-10-01

    This study investigates the hydraulic conductivity field and the groundwater flow pattern as predicted by a calibrated steady state groundwater flow model for the Keta Strip, southeastern Ghana. The hydraulic conductivity field is an important parameter in evaluating aquifer properties in space, and in general basin-wide groundwater resources evaluation and management. This study finds that the general hydraulic conductivity of the unconsolidated unconfined aquifer system of the Keta Strip ranges between 2 m/d and 20 m/d, with an average of 15 m/d. The spatial variation in horizontal hydraulic conductivity appears to take the trend in the variations in the nature of the material in space. Calibrated groundwater recharge suggests that 6.9-34% of annual precipitation recharges the shallow aquifer system. This amount of recharge is significant and suggests high fortunes in terms of groundwater resources development for agriculture and industrial activities in the area. A spatial distribution of groundwater recharge from precipitation is presented in this study. The spatial pattern appears to take the form of the distribution in horizontal hydraulic conductivity, and suggests that the vertical hydraulic conductivity takes the same pattern of spatial variation as the horizontal hydraulic conductivity. This is consistent with observations in other areas. The resulting groundwater flow is dominated by local flow systems as the unconfined system is quite shallow. A general northeast - southwest flow pattern has been observed in the study area.

  3. Regional groundwater flow model for C, K. L. and P reactor areas, Savannah River Site, Aiken, SC

    International Nuclear Information System (INIS)

    Flach, G.P.

    2000-01-01

    A regional groundwater flow model encompassing approximately 100 mi2 surrounding the C, K, L, and P reactor areas has been developed. The reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department. The model provides a quantitative understanding of groundwater flow on a regional scale within the near surface aquifers and deeper semi-confined to confined aquifers. The model incorporates historical and current field characterization data up through Spring 1999. Model preprocessing is automated so that future updates and modifications can be performed quickly and efficiently. The CKLP regional reactor model can be used to guide characterization, perform scoping analyses of contaminant transport, and serve as a common base for subsequent finer-scale transport and remedial/feasibility models for each reactor area

  4. Regional groundwater flow model for C, K. L. and P reactor areas, Savannah River Site, Aiken, SC

    Energy Technology Data Exchange (ETDEWEB)

    Flach, G.P.

    2000-02-11

    A regional groundwater flow model encompassing approximately 100 mi2 surrounding the C, K, L, and P reactor areas has been developed. The reactor flow model is designed to meet the planning objectives outlined in the General Groundwater Strategy for Reactor Area Projects by providing a common framework for analyzing groundwater flow, contaminant migration and remedial alternatives within the Reactor Projects team of the Environmental Restoration Department. The model provides a quantitative understanding of groundwater flow on a regional scale within the near surface aquifers and deeper semi-confined to confined aquifers. The model incorporates historical and current field characterization data up through Spring 1999. Model preprocessing is automated so that future updates and modifications can be performed quickly and efficiently. The CKLP regional reactor model can be used to guide characterization, perform scoping analyses of contaminant transport, and serve as a common base for subsequent finer-scale transport and remedial/feasibility models for each reactor area.

  5. Tracers Reveal Recharge Elevations, Groundwater Flow Paths and Travel Times on Mount Shasta, California

    Directory of Open Access Journals (Sweden)

    Elizabeth Peters

    2018-01-01

    Full Text Available Mount Shasta (4322 m is famous for its spring water. Water for municipal, domestic and industrial use is obtained from local springs and wells, fed by annual snow melt and sustained perennially by the groundwater flow system. We examined geochemical and isotopic tracers in samples from wells and springs on Mount Shasta, at the headwaters of the Sacramento River, in order to better understand the hydrologic system. The topographic relief in the study area imparts robust signatures of recharge elevation to both stable isotopes of the water molecule (δ18O and δD and to dissolved noble gases, offering tools to identify recharge areas and delineate groundwater flow paths. Recharge elevations determined using stable isotopes and noble gas recharge temperatures are in close agreement and indicate that most snowmelt infiltrates at elevations between 2000 m and 2900 m, which coincides with areas of thin soils and barren land cover. Large springs in Mt Shasta City discharge at an elevation more than 1600 m lower. High elevation springs (>2000 m yield very young water (<2 years while lower elevation wells (1000–1500 m produce water with a residence time ranging from 6 years to over 60 years, based on observed tritium activities. Upslope movement of the tree line in the identified recharge elevation range due to a warming climate is likely to decrease infiltration and recharge, which will decrease spring discharge and production at wells, albeit with a time lag dependent upon the length of groundwater flow paths.

  6. Groundwater flow model of the Estonian oil shale mining area towards to innovative system

    Energy Technology Data Exchange (ETDEWEB)

    Lind, H. [Tallinn Univ. of Technology (Estonia). Dept. of Mining

    2010-07-01

    Changes in the Estonian groundwater regime are anticipated as oil shale deposits are mined. This paper described a dynamic groundwater flow model used to develop a 3-D groundwater elevation map of the Estonian oil shale mining area. The model was used to provide preliminary estimations of water inflow into the working underground mine areas. The model included 9 closed underground mines, 5 active mine sites, and 2 small open-cast sites. The closed mine sites were filled with water flowing in from the working mine sites. New mines and dewatering programs are planned for the future. A database from observation wells installed within the Keila-Kukruse aquifer was used to extract outputs and determine time steps. The model included 35 pumping stations from the active mine sites. The hydraulic properties for each model layer were defined in 4 model zones. Results of the model showed higher water in-flows from the closed underground sites than earlier predictions had anticipated. 9 refs., 1 tab., 4 figs.

  7. Groundwater flow due to a nonlinear wave set-up on a permeable beach

    Directory of Open Access Journals (Sweden)

    Anna Przyborska

    2014-06-01

    Full Text Available Water flow through the beach body plays an important role in the biological status of the organisms inhabiting the beach sand. For tideless seas, the groundwater flow in shallow water is governed entirely by the surface wave dynamics on the beach. As waves propagate towards the shore, they become steeper owing to the decreasing water depth and at some depth, the waves lose their stability and start to break. When waves break, their energy is dissipated and the spatial changes of the radiation stress give rise to changes in the mean sea level, known as the set-up. The mean shore pressure gradient due to the wave set-up drives the groundwater circulation within the beach zone. This paper discusses the circulation of groundwater resulting from a nonlinear set-up. The circulation of flow is compared with the classic Longuet-Higgins (1983 solution and the time series of the set-up is considered for a 24 h storm. Water infiltrates into the coastal aquifer on the upper part of the beach near the maximum run-up and exfiltration occurs on the lower part of the beach face near the breaking point.

  8. Groundwater flow simulation of the Savannah River Site general separations area

    Energy Technology Data Exchange (ETDEWEB)

    Flach, G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Bagwell, L. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Bennett, P. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

    2017-09-07

    The most recent groundwater flow model of the General Separations Area, Savannah River Site, is referred to as the “GSA/PORFLOW” model. GSA/PORFLOW was developed in 2004 by porting an existing General Separations Area groundwater flow model from the FACT code to the PORFLOW code. The preceding “GSA/FACT” model was developed in 1997 using characterization and monitoring data through the mid-1990’s. Both models were manually calibrated to field data. Significantly more field data have been acquired since the 1990’s and model calibration using mathematical optimization software has become routine and recommended practice. The current task involved updating the GSA/PORFLOW model using selected field data current through at least 2015, and use of the PEST code to calibrate the model and quantify parameter uncertainty. This new GSA groundwater flow model is named “GSA2016” in reference to the year in which most development occurred. The GSA2016 model update is intended to address issues raised by the DOE Low-Level Waste (LLW) Disposal Facility Federal Review Group (LFRG) in a 2008 review of the E-Area Performance Assessment, and by the Nuclear Regulatory Commission in reviews of tank closure and Saltstone Disposal Facility Performance Assessments.

  9. Common problematic aspects of coupling hydrological models with groundwater flow models on the river catchment scale

    Directory of Open Access Journals (Sweden)

    R. Barthel

    2006-01-01

    Full Text Available Model coupling requires a thorough conceptualisation of the coupling strategy, including an exact definition of the individual model domains, the "transboundary" processes and the exchange parameters. It is shown here that in the case of coupling groundwater flow and hydrological models – in particular on the regional scale – it is very important to find a common definition and scale-appropriate process description of groundwater recharge and baseflow (or "groundwater runoff/discharge" in order to achieve a meaningful representation of the processes that link the unsaturated and saturated zones and the river network. As such, integration by means of coupling established disciplinary models is problematic given that in such models, processes are defined from a purpose-oriented, disciplinary perspective and are therefore not necessarily consistent with definitions of the same process in the model concepts of other disciplines. This article contains a general introduction to the requirements and challenges of model coupling in Integrated Water Resources Management including a definition of the most relevant technical terms, a short description of the commonly used approach of model coupling and finally a detailed consideration of the role of groundwater recharge and baseflow in coupling groundwater models with hydrological models. The conclusions summarize the most relevant problems rather than giving practical solutions. This paper aims to point out that working on a large scale in an integrated context requires rethinking traditional disciplinary workflows and encouraging communication between the different disciplines involved. It is worth noting that the aspects discussed here are mainly viewed from a groundwater perspective, which reflects the author's background.

  10. Groundwater-risk analysis of New York utilizing GIS technology

    Science.gov (United States)

    Hillenbrand, Charles John, III

    Using Geographic Information System (GIS) technology, data layers can be processed and analyzed to produce a regional groundwater-risk grid of New York State (NYS). GIS can be used to assess the potential to introduce contaminants at the ground surface, and assess the potential for the contaminants to migrate through the vadose zone and be introduced to an aquifer at the water-table. The potential to introduce contaminants to the ground surface was assessed utilizing existing database information in combination with the United States Geological Survey (USGS) Multi-Resolution Land Classification (MRLC) land use grid. The databases allowed an analysis of contaminant association with Standard Industrial Classification (SIC) codes, risk evaluation of the contaminants using groundwater intake values protective of human health, the development of SIC code-risk values, the construction of a SIC code-risked facility point coverage, and the construction of a land use-risk grid; this grid assesses the potential to introduce contaminants to the ground surface. Aquifer susceptibility was determined by analyzing vadose zone residence time assuming saturated conditions. Vadose zone residence time is a measure of the vadose zone's ability to attenuate and retard the migration of contaminants. Existing data layers were processed to produce a depth to water-table (vadose zone thickness) grid. Existing GIS data layers of soil, surficial geology and bedrock geology, along with review of literature and pump/slug test data, enabled the creation of thickness, porosity and vertical hydraulic conductivity grids for the three considered components of the vadose zone. The average linear velocity was then calculated for each vadose zone component by dividing their hydraulic conductivity grid by their respective porosity grid. The thickness grid of each vadose zone component was then divided by their respective average linear velocity grid to produce vadose zone residence time grids. The sum

  11. NAMMU results for the regional groundwater flow in the Piceance Basin - HYDROCOIN Level 2-Test case 4

    International Nuclear Information System (INIS)

    Miller, D.R.; Paige, R.W.

    1988-07-01

    The HYDROCOIN project is an international collaborative venture for comparing groundwater flow models and modelling strategies. Level 2 of this project concerns the validation of models in order to test their ability adequately to represent reality. This report describes calculations for the regional groundwater flow in the Piceance Basin of northwestern Colorado. This region constitutes one of the few areas where low permeability rocks, similar to those likely to be used for repository sites, have been investigated by hydrogeologists. (author)

  12. The Practical Application of Aqueous Geochemistry in Mapping Groundwater Flow Systems in Fractured Rock Masses

    Science.gov (United States)

    Bursey, G.; Seok, E.; Gale, J. E.

    2017-12-01

    Flow to underground mines and open pits takes place through an interconnected network of regular joints/fractures and intermediate to large scale structural features such as faults and fracture zones. Large scale features can serve either as high permeability pathways or as barriers to flow, depending on the internal characteristics of the structure. Predicting long term water quality in barrier-well systems and long-term mine water inflows over a mine life, as a mine expands, requires the use of a 3D numerical flow and transport code. The code is used to integrate the physical geometry of the fractured-rock mass with porosity, permeability, hydraulic heads, storativity and recharge data and construct a model of the flow system. Once that model has been calibrated using hydraulic head and permeability/inflow data, aqueous geochemical and isotopic data provide useful tools for validating flow-system properties, when one is able to recognize and account for the non-ideal or imperfect aspects of the sampling methods used in different mining environments. If groundwater samples are collected from discrete depths within open boreholes, water in those boreholes have the opportunity to move up or down in response to the forces that drive groundwater flow, whether they be hydraulic gradients, gas pressures, or density differences associated with variations in salinity. The use of Br/Cl ratios, for example, can be used to determine if there is active flow into, or out of, the boreholes through open discontinuities in the rock mass (i.e., short-circuiting). Natural groundwater quality can also be affected to varying degrees by mixing with drilling fluids. The combined use of inorganic chemistry and stable isotopes can be used effectively to identify dilution signals and map the dilution patterns through a range of fresh, brackish and saline water types. The stable isotopes of oxygen and hydrogen are nearly ideal natural tracers of water, but situations occur when deep

  13. Simulation of the effects of ground-water withdrawals and recharge on ground-water flow in Cape Cod, Martha's Vineyard, and Nantucket Island basins, Massachusetts

    Science.gov (United States)

    Masterson, John P.; Barlow, Paul M.

    1994-01-01

    The effects of changing patterns of ground-water pumping and aquifer recharge on the surface-water and ground-water hydrologic systems were determined for the Cape Cod, Martha's Vineyard, and Nantucket Island Basins. Three-dimensional, transient, ground-water-flow modelS that simulate both freshwater and saltwater flow were developed for the f1ow cells of Cape Cod which currently have large-capacity public-supply wells. Only the freshwater-flow system was simulated for the Cape Cod flow cells where public-water supply demands are satisfied by small-capacity domestic wells. Two- dimensional, finite-difference, change models were developed for Martha's Vineyard and Nantucket Island to determine the projected drawdowns in response to projected in-season pumping rates for 180 days of no aquifer recharge. Results of the simulations indicate very little change in the position of the freshwater-saltwater interface from predevelopment flow conditions to projected ground-water pumping and recharge rates for Cape Cod in the year 2020. Results of change model simulations for Martha's Vineyard and Nantucket Island indicate that the greatest impact in response to projected in-season ground-water pumping occurs at the pumping centers and the magnitude of the drawdowns are minimal with respect to the total thickness of the aquifers.

  14. Use of Groundwater Chemistry to Evaluate Subsurface Flow at Yucca Mountain, Nevada

    Science.gov (United States)

    Coleman, N. M.; Dam, W. L.

    2001-12-01

    Yucca Mountain, Nevada is a potential site for the disposal of high-level nuclear wastes. Groundwater at the site occurs in Tertiary volcanic tuffs and in Quaternary valley fill alluvium at lower elevations in the Amargosa Desert. Groundwater seeps downward to the water table through a thick unsaturated zone (UZ), then flows south and southeasterly from Yucca Mountain toward Fortymile Wash. The wash is a highly ephemeral watercourse that drains Fortymile Canyon and Jackass Flats southward. The wash crosses Highway 95 just west of Lathrop Wells, Nevada. Water table contours in Jackass Flats show that groundwater flow strongly converges on the axis of Fortymile Wash, indicating that the same structural conditions that cause topographic lows in the area also enhance the southerly flow of groundwater. Groundwater chemistry is being used to evaluate flow conditions at local and regional scales, and to help resolve technical issues concerning UZ and saturated zone (SZ) flow conditions and dilution processes. A number of perched zones have been found beneath Yucca Mt. in five different wells (Patterson et al., 1998). The major element chemistry of perched water is distinct from pore water chemistry in the UZ and more similar to the water chemistry of the SZ. The perched water is more dilute than the UZ pore waters, with generally lower chloride concentrations. The lower chloride concentration suggests that a fraction of the perched water is recharge that moves downward from the surface through fractures, and has less interaction with the host rock than pore waters. However, only 1 of 5 wells yielded perched water with bomb-pulse levels of tritium. Deuterium and O-18 stable isotope chemistry indicates that perched water has an intermediate composition when compared to SZ groundwater. It is isotopically heavier (less negative) than SZ water beneath Yucca Mountain, but lighter than groundwater from wells along Fortymile Wash where significant recharge occurs. The heaviest

  15. Regional ground-water flow modeling for the Paradox Basin, Utah: Second status report

    International Nuclear Information System (INIS)

    1986-09-01

    Regional ground-water flow within the principal geohydrologic units of the Paradox Basin is evaluated by developing a conceptual model of the flow regime between the shallow aquifers, the Paradox salt and the deep-basin brine aquifers. This model is tested using a three-dimensional, finite-difference flow code. Sensitivity analyses (a limited parametric study) are conducted to define the system responses to changes in the conceptual model. The conceptual model is described in terms of its areal and vertical discretization, aquifer properties, fluid properties, and hydrologic boundary conditions. The simulated results are described with potentiometric surfaces, tables summarizing the areal and vertical volumetric flows through the principal units, and Darcy velocities at specified points. The reported work is the second stage of an ongoing evaluation of the Gisbon Dome area within the Paradox Basin as a potential repository for high-level radioactive wastes. The results and conclusions should thus be considered preliminary and subject to modification with the collection of additional data. However, the report does provide a useful basis for describing the sensitivity of the present conceptualization of ground-water flow to the hydrologic parameters and, to a lesser extent, the uncertainties of the present conceptualization. 20 refs., 17 figs., 9 tabs

  16. Vertical groundwater flow in Permo-Triassic sediments underlying two cities in the Trent River Basin (UK)

    Science.gov (United States)

    Taylor, R. G.; Cronin, A. A.; Trowsdale, S. A.; Baines, O. P.; Barrett, M. H.; Lerner, D. N.

    2003-12-01

    The vertical component of groundwater flow that is responsible for advective penetration of contaminants in sandstone aquifers is poorly understood. This lack of knowledge is of particular concern in urban areas where abstraction disrupts natural groundwater flow regimes and there exists an increased density of contaminant sources. Vertical hydraulic gradients that control vertical groundwater flow were investigated using bundled multilevel piezometers and a double-packer assembly in dedicated boreholes constructed to depths of between 50 and 92 m below ground level in Permo-Triassic sediments underlying two cities within the Trent River Basin of central England (Birmingham, Nottingham). The hydrostratigraphy of the Permo-Triassic sediments, indicated by geophysical logging and hydraulic (packer) testing, demonstrates considerable control over observed vertical hydraulic gradients and, hence, vertical groundwater flow. The direction and magnitude of vertical hydraulic gradients recorded in multilevel piezometers and packers are broadly complementary and range, within error, from +0.1 to -0.7. Groundwater is generally found to flow vertically toward transmissive zones within the hydrostratigraphical profile though urban abstraction from the Sherwood Sandstone aquifer also influences observed vertical hydraulic gradients. Bulk, downward Darcy velocities at two locations affected by abstraction are estimated to be in the order of several metres per year. Consistency in the distribution of hydraulic head with depth in Permo-Triassic sediments is observed over a one-year period and adds support the deduction of hydrostratigraphic control over vertical groundwater flow.

  17. Modeling of groundwater flow for Mujib aquifer, Jordan

    Indian Academy of Sciences (India)

    Different scenarios were considered to predict aquifer system response under different conditions. The results of the sensitivity analysis show that ... decision makers and planners in selecting optimum management schemes suitable for arid .... Qatrana city where no water exists in the. B2/A7 aquifer. The proposed boundary ...

  18. Comparing groundwater recharge and base flow in the Bukmoongol ...

    Indian Academy of Sciences (India)

    High soil organic matter features is prevalent in most parts of the area. The saturated hydraulic conductivity of the watershed was estimated at 15.32 mm/h. The climate is classified as ... topography and soil characteristics. The water level from ...... nan S and Tripathy D 2005 Automated web GIS based hydrograph analysis ...

  19. Sequoyah Nuclear Plant low-level radwaste storage facility ground-water pathway analysis

    International Nuclear Information System (INIS)

    Boggs, J.M.

    1982-10-01

    The proposed low-level radwaste storage facility (LLRWSF) at Sequoyah Nuclear Plant is underlain by soils having low hydraulic conductivity and high sorptive capacity which greatly reduce the risks associated with a potential contaminant excursion. A conservative ground-water pathway accident analysis using flow and solute transport modeling techniques indicates that without interdiction radiological contaminant concentrations in ground water discharging into Chickamauga Lake would be well below 10 CFR Part 20 criteria. There are no potential impacts to ground-water users since there are no private wells in the site vicinity and no potential for future ground-water development. Routine ground-water monitoring is not recommended at the LLRWSF except in the unlikely event of an accident. Although the analysis indicates that the existing monitor well network designed for the originally planned long-term LLRWSF is not the most effective monitor system for the current emergency storage facility, no additional monitor wells are recommended at this time. The extremely slow rate of contaminant movement would allow sufficient time to install additional wells if necessary should an accident occur. Accident mitigation is unwarranted from a technical viewpoint. However, if mitigation is necessary for other reasons, removal of contaminated soils is judged the most cost-effective method

  20. Subcubic Control Flow Analysis Algorithms

    DEFF Research Database (Denmark)

    Midtgaard, Jan; Van Horn, David

    We give the first direct subcubic algorithm for performing control flow analysis of higher-order functional programs. Despite the long held belief that inclusion-based flow analysis could not surpass the ``cubic bottleneck, '' we apply known set compression techniques to obtain an algorithm...... that runs in time O(n^3/log n) on a unit cost random-access memory model machine. Moreover, we refine the initial flow analysis into two more precise analyses incorporating notions of reachability. We give subcubic algorithms for these more precise analyses and relate them to an existing analysis from...

  1. Bedrock Hydrogeology-Groundwater flow modelling. Site investigation SFR

    International Nuclear Information System (INIS)

    Oehman, Johan; Follin, Sven; Oden, Magnus

    2013-05-01

    The hydrogeological model developed for the SFR extension project (PSU) consists of 40 geologically modelled deformation zones (DZ) and 8 sub-horizontal structural-hydraulic features, called SBAstructures, not defined in the geological model. However, some of the SBA-structures coincide with what is defined as unresolved possible deformation zones (Unresolved PDZ) in the geological modelling. In addition, the hydrogeological model consists of a stochastic discrete fracture network (DFN) model intended for the less fractured rock mass volumes (fracture domains) between the zones and the SBA-structures, and a stochastic fracture model intended to handle remaining Unresolved PDZs in the geological modelling not modelled as SBA-structures in the hydrogeological modelling. The four structural components of the bedrock in the hydrogeological model, i.e. DZ, SBA, Unresolved PDZ and DFN, are assigned hydraulic properties in the hydrogeological model based on the transmissivities interpreted from single-hole hydraulic tests. The main objective of the present work is to present the characteristics of the hydrogeological model with regard to the needs of the forthcoming safety assessment SR-PSU. In concrete words, simulated data are compared with measured data, i.e. hydraulic heads in boreholes and tunnel inflow to the existing repository (SFR). The calculations suggest that the available data for flow model calibration cannot be used to motivate a substantial adjustment of the initial hydraulic parameterisation (assignment of hydraulic properties) of the hydrogeological model. It is suggested that uncertainties in the hydrogeological model are studied in the safety assessment SR-PSU by means of a large number of calculation cases. These should address hydraulic heterogeneity of deterministic structures (DZ and SBA) and realisations of stochastic fractures/fracture networks (Unresolved PDZ and DFN) within the entire SFR Regional model domain

  2. Bedrock Hydrogeology - Groundwater flow modelling. Site investigation SFR

    Energy Technology Data Exchange (ETDEWEB)

    Oehman, Johan [Geosigma AB, Uppsala (Sweden); Follin, Sven [SF GeoLogic AB, Taeby (Sweden); Oden, Magnus [SKB, Stockholm (Sweden)

    2013-05-15

    The hydrogeological model developed for the SFR extension project (PSU) consists of 40 geologically modelled deformation zones (DZ) and 8 sub-horizontal structural-hydraulic features, called SBAstructures, not defined in the geological model. However, some of the SBA-structures coincide with what is defined as unresolved possible deformation zones (Unresolved PDZ) in the geological modelling. In addition, the hydrogeological model consists of a stochastic discrete fracture network (DFN) model intended for the less fractured rock mass volumes (fracture domains) between the zones and the SBA-structures, and a stochastic fracture model intended to handle remaining Unresolved PDZs in the geological modelling not modelled as SBA-structures in the hydrogeological modelling. The four structural components of the bedrock in the hydrogeological model, i.e. DZ, SBA, Unresolved PDZ and DFN, are assigned hydraulic properties in the hydrogeological model based on the transmissivities interpreted from single-hole hydraulic tests. The main objective of the present work is to present the characteristics of the hydrogeological model with regard to the needs of the forthcoming safety assessment SR-PSU. In concrete words, simulated data are compared with measured data, i.e. hydraulic heads in boreholes and tunnel inflow to the existing repository (SFR). The calculations suggest that the available data for flow model calibration cannot be used to motivate a substantial adjustment of the initial hydraulic parameterisation (assignment of hydraulic properties) of the hydrogeological model. It is suggested that uncertainties in the hydrogeological model are studied in the safety assessment SR-PSU by means of a large number of calculation cases. These should address hydraulic heterogeneity of deterministic structures (DZ and SBA) and realisations of stochastic fractures/fracture networks (Unresolved PDZ and DFN) within the entire SFR Regional model domain.

  3. A study on evaluation and analytical methods for groundwater flow with considering sea/fresh-water boundary. 1

    Energy Technology Data Exchange (ETDEWEB)

    Anezaki, S. [Taisei Corp., Tokyo (Japan)

    1998-03-01

    Sea/fresh-water boundary caused by density and concentration balance of sea-water and fresh-water is an important item for groundwater flow evaluation in deep underground near the coast. Also, in order to evaluate groundwater quality, it is important to understand the characteristics of sea/fresh-water boundary, for example boundary shape, salt distribution. In order to establish the evaluation and analytical methods for groundwater flow with considering sea/fresh-water boundary, we investigated the following items in this study. (1) Literature survey and data collection. (2) Investigation of analytical methods. (3) Planning of further study. (author). 78 refs.

  4. The Ozark Plateaus Regional Aquifer Study—Documentation of a groundwater-flow model constructed to assess water availability in the Ozark Plateaus

    Science.gov (United States)

    Clark, Brian R.; Richards, Joseph M.; Knierim, Katherine J.

    2018-03-30

    Recent short-term drought conditions have emphasized the need to better understand the delicate balance between abundance, sustainability, and scarcity of groundwater in the Ozark Plateaus aquifer system. In 2014, the U.S. Geological Survey began construction of a groundwater-flow model as a tool for the assessment of groundwater availability in the Ozark Plateaus aquifer system. The model was developed to benefit concurrent and future investigations involving groundwater-pumping scenarios, optimization, particle transport, and groundwater-monitoring network analysis.The groundwater model simulates 116 years (1900–2015) of hydrologic conditions and the response of the groundwater system to changes in stress including changes in recharge and groundwater pumping for water supply. Semiseasonal stress periods were simulated from the later part of 1991 to 2015 and represent higher demand and lower recharge in the spring and summer months and lower demand and higher recharge in the fall and winter months. Groundwater pumping increases throughout the simulation period with a maximum rate of about 600 million gallons per day (Mgal/d).The process of matching historical hydrologic data for the Ozark Plateaus aquifer system model was accomplished by a combination of manual changes to parameter values and automated calibration methods. Observation data used in the development and evaluation of the model included 19,045 hydraulic-head observations from 6,683 wells within the model area. Observation data also included stream leakage estimates summed to calculate a net gain or net loss value for approximately 81 named streams.The majority (mean of over 95 percent) of the recharge component is discharged through streams simulated in the model. The total simulated discharge to streams fluctuates seasonally between 7,500 and 17,500 Mgal/d with a mean outflow of 11,500 Mgal/d. Much of the remaining balance between modeled recharge inflows and stream outflows is made up by water

  5. Hydrogeologic evaluation and numerical simulation of the Death Valley regional ground-water flow system, Nevada and California

    International Nuclear Information System (INIS)

    D'Agnese, F.A.; Faunt, C.C.; Turner, A.K.; Hill, M.C.

    1997-01-01

    Yucca Mountain is being studied as a potential site for a high-level radioactive waste repository. In cooperation with the U.S. Department of Energy, the U.S. Geological Survey is evaluating the geologic and hydrologic characteristics of the ground-water system. The study area covers approximately 100,000 square kilometers between lat 35 degrees N., long 115 degrees W and lat 38 degrees N., long 118 degrees W and encompasses the Death Valley regional ground-water flow system. Hydrology in the region is a result of both the and climatic conditions and the complex described as dominated by interbasinal flow and may be conceptualized as having two main components: a series of relatively shallow and localized flow paths that are superimposed on deeper regional flow paths. A significant component of the regional ground-water flow is through a thick Paleozoic carbonate rock sequence. Throughout the regional flow system, ground-water flow is probably controlled by extensive and prevalent structural features that result from regional faulting and fracturing. Hydrogeologic investigations over a large and hydrogeologically complex area impose severe demands on data management. This study utilized geographic information systems and geoscientific information systems to develop, store, manipulate, and analyze regional hydrogeologic data sets describing various components of the ground-water flow system

  6. Hydrogeologic evaluation and numerical simulation of the Death Valley regional ground-water flow system, Nevada and California

    Energy Technology Data Exchange (ETDEWEB)

    D`Agnese, F.A.; Faunt, C.C.; Turner, A.K.; Hill, M.C.

    1997-12-31

    Yucca Mountain is being studied as a potential site for a high-level radioactive waste repository. In cooperation with the U.S. Department of Energy, the U.S. Geological Survey is evaluating the geologic and hydrologic characteristics of the ground-water system. The study area covers approximately 100,000 square kilometers between lat 35{degrees}N., long 115{degrees}W and lat 38{degrees}N., long 118{degrees}W and encompasses the Death Valley regional ground-water flow system. Hydrology in the region is a result of both the and climatic conditions and the complex described as dominated by interbasinal flow and may be conceptualized as having two main components: a series of relatively shallow and localized flow paths that are superimposed on deeper regional flow paths. A significant component of the regional ground-water flow is through a thick Paleozoic carbonate rock sequence. Throughout the regional flow system, ground-water flow is probably controlled by extensive and prevalent structural features that result from regional faulting and fracturing. Hydrogeologic investigations over a large and hydrogeologically complex area impose severe demands on data management. This study utilized geographic information systems and geoscientific information systems to develop, store, manipulate, and analyze regional hydrogeologic data sets describing various components of the ground-water flow system.

  7. Hydrochemical analysis of groundwater using multivariate statistical methods - The Volta region, Ghana

    Science.gov (United States)

    Banoeng-Yakubo, B.; Yidana, S.M.; Nti, E.

    2009-01-01

    Q and R-mode multivariate statistical analyses were applied to groundwater chemical data from boreholes and wells in the northern section of the Volta region Ghana. The objective was to determine the processes that affect the hydrochemistry and the variation of these processes in space among the three main geological terrains: the Buem formation, Voltaian System and the Togo series that underlie the area. The analyses revealed three zones in the groundwater flow system: recharge, intermediate and discharge regions. All three zones are clearly different with respect to all the major chemical parameters, with concentrations increasing from the perceived recharge areas through the intermediate regions to the discharge areas. R-mode HCA and factor analysis (using varimax rotation and Kaiser Criterion) were then applied to determine the significant sources of variation in the hydrochemistry. This study finds that groundwater hydrochemistry in the area is controlled by the weathering of silicate and carbonate minerals, as well as the chemistry of infiltrating precipitation. This study finds that the ??D and ??18O data from the area fall along the Global Meteoric Water Line (GMWL). An equation of regression derived for the relationship between ??D and ??18O bears very close semblance to the equation which describes the GMWL. On the basis of this, groundwater in the study area is probably meteoric and fresh. The apparently low salinities and sodicities of the groundwater seem to support this interpretation. The suitability of groundwater for domestic and irrigation purposes is related to its source, which determines its constitution. A plot of the sodium adsorption ratio (SAR) and salinity (EC) data on a semilog axis, suggests that groundwater serves good irrigation quality in the area. Sixty percent (60%), 20% and 20% of the 67 data points used in this study fall within the medium salinity - low sodicity (C2-S1), low salinity -low sodicity (C1-S1) and high salinity - low

  8. Hydrogeology of, and simulation of ground-water flow in a mantled carbonate-rock system, Cumberland Valley, Pennsylvania

    Science.gov (United States)

    Chichester, D.C.

    1996-01-01

    The U.S. Geological Survey conducted a study in a highly productive and complex regolith-mantled carbonate valley in the northeastern part of the Cumberland Valley, Pa., as part of its Appalachian Valleys and Piedmont Regional Aquifer-system Analysis program. The study was designed to quantify the hydrogeologic characteristics and understand the ground-water flow system of a highly productive and complex thickly mantled carbonate valley. The Cumberland Valley is characterized by complexly folded and faulted carbonate bedrock in the valley bottom, by shale and graywacke to the north, and by red-sedimentary and diabase rocks in the east-southeast. Near the southern valley hillslope, the carbonate rock is overlain by wedge-shaped deposit of regolith, up to 450 feet thick, that is composed of residual material, alluvium, and colluvium. Locally, saturated regolith is greater than 200 feet thick. Seepage-run data indicate that stream reaches, near valley walls, are losing water from the stream, through the regolith, to the ground-water system. Results of hydrograph-separation analyses indicate that base flow in stream basins dominated by regolith-mantled carbonate rock, carbonate rock, and carbonate rock and shale are 81.6, 93.0, and 67.7 percent of total streamflow, respectively. The relative high percentage for the regolith-mantled carbonate-rock basin indicates that the regolith stores precipitation and slowly, steadily releases this water to the carbonate-rock aquifer and to streams as base flow. Anomalies in water-table gradients and configuration are a result of topography and differences in the character and distribution of overburden material, permeability, rock type, and geologic structure. Most ground-water flow is local, and ground water discharges to nearby springs and streams. Regional flow is northeastward to the Susquehanna River. Average-annual water budgets were calculated for the period of record from two continuous streamflow-gaging stations. Average

  9. A conceptual model for the analysis of multi-stressors in linked groundwater-surface water systems.

    Science.gov (United States)

    Kaandorp, Vince P; Molina-Navarro, Eugenio; Andersen, Hans E; Bloomfield, John P; Kuijper, Martina J M; de Louw, Perry G B

    2018-02-02

    Groundwater and surface water are often closely coupled and are both under the influence of multiple stressors. Stressed groundwater systems may lead to a poor ecological status of surface waters but to date no conceptual framework to analyse linked multi-stressed groundwater - surface water systems has been developed. In this paper, a framework is proposed showing the effect of groundwater on surface waters in multiple stressed systems. This framework will be illustrated by applying it to four European catchments, the Odense, Denmark, the Regge and Dinkel, Netherlands, and the Thames, UK, and by assessing its utility in analysing the propagation or buffering of multi-stressors through groundwater to surface waters in these catchments. It is shown that groundwater affects surface water flow, nutrients and temperature, and can both propagate stressors towards surface waters and buffer the effect of stressors in space and time. The effect of groundwater on drivers and states depends on catchment characteristics, stressor combinations, scale and management practises. The proposed framework shows how groundwater in lowland catchments acts as a bridge between stressors and their effects within surface waters. It shows water managers how their management areas might be influenced by groundwater, and helps them to include this important, but often overlooked part of the water cycle in their basin management plans. The analysis of the study catchments also revealed a lack of data on the temperature of both groundwater and surface water, while it is an important parameter considering future climate warming. Copyright © 2018. Published by Elsevier B.V.

  10. 3-D numerical modelling of groundwater flow for scenario-based ...

    African Journals Online (AJOL)

    2018-04-02

    Apr 2, 2018 ... analysis and management ... gauges, well logs, meteorological and lithological information were collected from Punjab Irrigation Department (PID),. Water .... network. The transport of water through this irrigation network contributes a major recharge to groundwater at different stages of the irrigation system.

  11. Flow Injection Analysis

    DEFF Research Database (Denmark)

    Hansen, Elo Harald

    1998-01-01

    Learning objectives:* To provide an introduction to automated assays* To describe the basic principles of FIA * To demonstrate the capabilities of FIA in relation to batch assays and conventional continuous flow systems* To show that FIA allows one to augment existing analytical techniques* To show...

  12. Semi-analytical solutions of groundwater flow in multi-zone (patchy) wedge-shaped aquifers

    Science.gov (United States)

    Samani, Nozar; Sedghi, Mohammad M.

    2015-03-01

    Alluvial fans are potential sites of potable groundwater in many parts of the world. Characteristics of alluvial fans sediments are changed radially from high energy coarse-grained deposition near the apex to low energy fine-grained deposition downstream so that patchy wedge-shaped aquifers with radial heterogeneity are formed. The hydraulic parameters of the aquifers (e.g. hydraulic conductivity and specific storage) change in the same fashion. Analytical or semi-analytical solutions of the flow in wedge-shaped aquifers are available for homogeneous cases. In this paper we derive semi-analytical solutions of groundwater flow to a well in multi-zone wedge-shaped aquifers. Solutions are provided for three wedge boundary configurations namely: constant head-constant head wedge, constant head-barrier wedge and barrier-barrier wedge. Derivation involves the use of integral transforms methods. The effect of heterogeneity ratios of zones on the response of the aquifer is examined. The results are presented in form of drawdown and drawdown derivative type curves. Heterogeneity has a significant effect on over all response of the pumped aquifer. Solutions help understanding the behavior of heterogeneous multi-zone aquifers for sustainable development of the groundwater resources in alluvial fans.

  13. Information Flow Analysis for VHDL

    DEFF Research Database (Denmark)

    Tolstrup, Terkel Kristian; Nielson, Flemming; Nielson, Hanne Riis

    2005-01-01

    We describe a fragment of the hardware description language VHDL that is suitable for implementing the Advanced Encryption Standard algorithm. We then define an Information Flow analysis as required by the international standard Common Criteria. The goal of the analysis is to identify the entire...... information flow through the VHDL program. The result of the analysis is presented as a non-transitive directed graph that connects those nodes (representing either variables or signals) where an information flow might occur. We compare our approach to that of Kemmerer and conclude that our approach yields...

  14. Deep reaching fluid flow in the North East German Basin: origin and processes of groundwater salinisation

    Science.gov (United States)

    Tesmer, M.; Möller, P.; Wieland, S.; Jahnke, C.; Voigt, H.; Pekdeger, A.

    2007-11-01

    Major element chemistry, rare-earth element distribution, and H and O isotopes are conjointly used to study the sources of salinisation and interaquifer flow of saline groundwater in the North East German Basin. Chemical analyses from hydrocarbon exploration campaigns showed evidence of the existence of two different groups of brines: halite and halite Ca-Cl brines. Residual brines and leachates are identified by Br-/Cl- ratios. Most of the brines are dissolution brines of Permian evaporites. New analyses show that the pattern of rare-earth elements and yttrium (REY) are closely linked to H and O isotope distribution. Thermal brines from deep wells and artesian wells indicate isotopically evaporated brines, which chemically interacted with their aquifer environment. Isotopes and rare-earth element patterns prove that cross flow exists, especially in the post-Rupelian aquifer. However, even at depths exceeding 2,000 m, interaquifer flow takes place. The rare-earth element pattern and H and O isotopes identify locally ascending brines. A large-scale lateral groundwater flow has to be assumed because all pre-Rupelian aquifer systems to a depth of at least 500 m are isotopically characterised by Recent or Pleistocene recharge conditions.

  15. Estimating impacts of land use on groundwater quality using trilinear analysis

    Science.gov (United States)

    Ying Ouyang; Jia-En Zhang; Lihua. Cui

    2014-01-01

    Groundwater is connected to the landscape above and is thus affected by the overlaying land uses. This study evaluated the impacts of land uses upon groundwater quality using trilinear analysis. Trilinear analysis is a display of experimental data in a triangular graph. Groundwater quality data collected from agricultural, septic tank, forest, and wastewater land uses...

  16. Isotope-hydrological models and calculational methods for investigation of groundwater flow

    International Nuclear Information System (INIS)

    Marton, L.

    1982-01-01

    Recharge of groundwater through a semi-confining bed is a typical hydrogeological phenomenon in quaternary deposits which are elevated to a lesser or greater degree above the surroundings. A simple hydrological model has been introduced in which the aquifer is recharged only by precipitation through a semi-permeable layer. For applying the model, it is necessary to know the age of the water or the radioisotope concentrations in some sections of the ground-water flow system. On the basis of the age, the hydraulic conductivity of the aquifer and of the semiconfining bed and the steady rate of infiltration can be calculated. Other hydraulic parameters can be determined with the help of a mathemathical model worked out by Freeze and Witherspoon. The hydrological and mathemathical models are inversely used and are complementary. The reliability and applicability of the hydrological model has been proved in practice and good results were gained in hydrogeological research carried out in Hungary. (author)

  17. Modeling of Groundwater Flow and Radionuclide Transport at the Climax Mine sub-CAU, Nevada Test Site

    Energy Technology Data Exchange (ETDEWEB)

    K. Pohlmann; M. Ye; D. Reeves; M. Zavarin; D. Decker; J. Chapman

    2007-09-28

    The Yucca Flat-Climax Mine Corrective Action Unit (CAU) on the Nevada Test Site comprises 747 underground nuclear detonations, all but three of which were conducted in alluvial, volcanic, and carbonate rocks in Yucca Flat. The remaining three tests were conducted in the very different hydrogeologic setting of the Climax Mine granite stock located in Area 15 at the northern end of Yucca Flat. As part of the Corrective Action Investigation (CAI) for the Yucca Flat-Climax Mine CAU, models of groundwater flow and radionuclide transport will be developed for Yucca Flat. However, two aspects of these CAU-scale models require focused modeling at the northern end of Yucca Flat beyond the capability of these large models. First, boundary conditions and boundary flows along the northern reaches of the Yucca Flat-Climax Mine CAU require evaluation to a higher level of detail than the CAU-scale Yucca Flat model can efficiently provide. Second, radionuclide fluxes from the Climax tests require analysis of flow and transport in fractured granite, a unique hydrologic environment as compared to Yucca Flat proper. This report describes the Climax Mine sub-CAU modeling studies conducted to address these issues, with the results providing a direct feed into the CAI for the Yucca Flat-Climax Mine CAU. Three underground nuclear detonations were conducted for weapons effects testing in the Climax stock between 1962 and 1966: Hard Hat, Pile Driver, and Tiny Tot. Though there is uncertainty regarding the position of the water table in the stock, it is likely that all three tests were conducted in the unsaturated zone. In the early 1980s, the Spent Fuel Test-Climax (SFT-C) was constructed to evaluate the feasibility of retrievable, deep geologic storage of commercial nuclear reactor wastes. Detailed mapping of fractures and faults carried out for the SFT-C studies greatly expanded earlier data sets collected in association with the nuclear tests and provided invaluable information for

  18. Identification of potential groundwater flow paths using geological and geophysical data

    International Nuclear Information System (INIS)

    Pohlmann, K.; Andricevic, R.

    1994-09-01

    This project represents the first phase in the development of a methodology for generating three-dimensional equiprobable maps of hydraulic conductivity for the Nevada Test Site (NTS). In this study, potential groundwater flow paths were investigated for subsurface tuffs at Yucca Flat by studying how these units are connected. The virtual absence of site-specific hydraulic conductivity data dictates that as a first step a surrogate attribute (geophysical logs) be utilized. In this first phase, the connectivity patterns of densely welded ash-flow tuffs were studied because these tuffs are the most likely to form zones of high hydraulic conductivity. Densely welded tuffs were identified based on the response shown on resistivity logs and this information was transformed into binary indicator values. The spatial correlation of the indicator data was estimated through geostatistical methods. Equiprobable three-dimensional maps of the distribution of the densely-welded and nonwelded tuffs (i.e., subsurface heterogeneity) were then produced using a multiple indicator simulation formalism. The simulations demonstrate that resistivity logs are effective as soft data for indicating densely welded tuffs. The simulated welded tuffs reproduce the stratigraphic relationships of the welded tuffs observed in hydrogeologic cross sections, while incorporating the heterogeneity and anisotropy that is expected in this subsurface setting. Three-dimensional connectivity of the densely welded tuffs suggests potential groundwater flow paths with lengths easily over 1 km. The next phase of this investigation should incorporate other geophysical logs (e.g., gamma-gamma logs) and then calibrate the resulting soft data maps with available hard hydraulic conductivity data. The soft data maps can then augment the hard data to produce the final maps of the spatial distribution of hydraulic conductivity that can be used as input for numerical solution of groundwater flow and transport

  19. Using SWAT-MODFLOW to simulate groundwater flow and groundwater-surface water interactions in an intensively irrigated stream-aquifer system

    Science.gov (United States)

    Wei, X.; Bailey, R. T.

    2017-12-01

    Agricultural irrigated watersheds in semi-arid regions face challenges such as waterlogging, high soil salinity, reduced crop yield, and leaching of chemical species due to extreme shallow water tables resulting from long-term intensive irrigation. Hydrologic models can be used to evaluate the impact of land management practices on water yields and groundwater-surface water interactions in such regions. In this study, the newly developed SWAT-MODFLOW, a coupled surface/subsurface hydrologic model, is applied to a 950 km2 watershed in the Lower Arkansas River Valley (southeastern Colorado). The model accounts for the influence of canal diversions, irrigation applications, groundwater pumping, and earth canal seepage losses. The model provides a detailed description of surface and subsurface flow processes, thereby enabling detailed description of watershed processes such as runoff, infiltration, in-streamflow, three-dimensional groundwater flow in a heterogeneous aquifer system with sources and sinks (e.g. pumping, seepage to subsurface drains), and spatially-variable surface and groundwater exchange. The model was calibrated and tested against stream discharge from 5 stream gauges in the Arkansas River and its tributaries, groundwater levels from 70 observation wells, and evapotranspiration (ET) data estimated from satellite (ReSET) data during the 1999 to 2007 period. Since the water-use patterns within the study area are typical of many other irrigated river valleys in the United States and elsewhere, this modeling approach is transferable to other regions.

  20. Geology, selected geophysics, and hydrogeology of the White River and parts of the Great Salt Lake Desert regional groundwater flow systems, Utah and Nevada

    Science.gov (United States)

    Rowley, Peter D.; Dixon, Gary L.; Watrus , James M.; Burns, Andrews G.; Mankinen, Edward A.; McKee, Edwin H.; Pari, Keith T.; Ekren, E. Bartlett; Patrick , William G.; Comer, John B.; Inkenbrandt, Paul C.; Krahulec, K.A.; Pinnell, Michael L.

    2016-01-01

    The east-central Great Basin near the Utah-Nevada border contains two great groundwater flow systems. The first, the White River regional groundwater flow system, consists of a string of hydraulically connected hydrographic basins in Nevada spanning about 270 miles from north to south. The northernmost basin is Long Valley and the southernmost basin is the Black Mountain area, a valley bordering the Colorado River. The general regional groundwater flow direction is north to south. The second flow system, the Great Salt Lake Desert regional groundwater flow system, consists of hydrographic basins that straddle

  1. Numerical study of wave effects on groundwater flow and solute transport in a laboratory beach.

    Science.gov (United States)

    Geng, Xiaolong; Boufadel, Michel C; Xia, Yuqiang; Li, Hailong; Zhao, Lin; Jackson, Nancy L; Miller, Richard S

    2014-09-01

    A numerical study was undertaken to investigate the effects of waves on groundwater flow and associated inland-released solute transport based on tracer experiments in a laboratory beach. The MARUN model was used to simulate the density-dependent groundwater flow and subsurface solute transport in the saturated and unsaturated regions of the beach subjected to waves. The Computational Fluid Dynamics (CFD) software, Fluent, was used to simulate waves, which were the seaward boundary condition for MARUN. A no-wave case was also simulated for comparison. Simulation results matched the observed water table and concentration at numerous locations. The results revealed that waves generated seawater-groundwater circulations in the swash and surf zones of the beach, which induced a large seawater-groundwater exchange across the beach face. In comparison to the no-wave case, waves significantly increased the residence time and spreading of inland-applied solutes in the beach. Waves also altered solute pathways and shifted the solute discharge zone further seaward. Residence Time Maps (RTM) revealed that the wave-induced residence time of the inland-applied solutes was largest near the solute exit zone to the sea. Sensitivity analyses suggested that the change in the permeability in the beach altered solute transport properties in a nonlinear way. Due to the slow movement of solutes in the unsaturated zone, the mass of the solute in the unsaturated zone, which reached up to 10% of the total mass in some cases, constituted a continuous slow release of solutes to the saturated zone of the beach. This means of control was not addressed in prior studies. Copyright © 2014 Elsevier B.V. All rights reserved.

  2. Simulation of recharge for the Death Valley regional groundwater flow system using an integrated hydrologic model

    Science.gov (United States)

    Hevesi, J. A.; Regan, R. S.; Hill, M. C.; Heywood, C.; Kohn, M. S.

    2012-12-01

    A proof-of-concept study was conducted using the integrated hydrologic model, GSFLOW, to simulate spatially and temporally distributed recharge for the Death Valley regional groundwater flow system (DVRFS). GSFLOW is an integrated groundwater - surface water flow model that combines two modeling applications: the Precipitation-Runoff-Modeling-System (PRMS) and MODFLOW. Previous methods used to estimate recharge for the DVRFS include empirical models based on precipitation, applications of the chloride mass-balance method, and applications of a precipitation-runoff model, INFIL, which used a daily time step to simulate recharge as net infiltration through the root zone. The GSFLOW model offers several potential advantages compared to the previous methods including (1) the ability to simulate complex flow through a thick unsaturated zone (UZ), allowing for the dampening and time delay of recharge relative to the infiltration signal at the top of the UZ and also allowing for the redistribution of flow within the UZ, as enabled by the MODFLOW-NWT and UZF capabilities, (2) the simulation of rejected recharge in response to the dynamics of groundwater discharge and low permeability zones in the UZ, (3) a more explicit representation of streamflow and recharge processes in the mostly ephemeral stream channels that characterize the DVRFS, and (4) the ability to simulate complex flow paths for runoff occurring as both overland flow and shallow subsurface flow (interflow) in the soil zone using a network of cascades connecting hydrologic response units (HRUs). Simulations were done using a daily time step for water years 1980-2010. Preliminary estimates of recharge using GSFLOW indicate that the distribution of recharge is highly variable both spatially and temporally due to variability in precipitation, snowmelt, evapotranspiration, runoff, and the permeability of bedrock and alluvium underlying the root zone. Results averaged over the areas of subbasins were similar to

  3. Data assimilation for groundwater flow modelling using Unbiased Ensemble Square Root Filter: Case study in Guantao, North China Plain

    Science.gov (United States)

    Li, N.; Kinzelbach, W.; Li, H.; Li, W.; Chen, F.; Wang, L.

    2017-12-01

    Data assimilation techniques are widely used in hydrology to improve the reliability of hydrological models and to reduce model predictive uncertainties. This provides critical information for decision makers in water resources management. This study aims to evaluate a data assimilation system for the Guantao groundwater flow model coupled with a one-dimensional soil column simulation (Hydrus 1D) using an Unbiased Ensemble Square Root Filter (UnEnSRF) originating from the Ensemble Kalman Filter (EnKF) to update parameters and states, separately or simultaneously. To simplify the coupling between unsaturated and saturated zone, a linear relationship obtained from analyzing inputs to and outputs from Hydrus 1D is applied in the data assimilation process. Unlike EnKF, the UnEnSRF updates parameter ensemble mean and ensemble perturbations separately. In order to keep the ensemble filter working well during the data assimilation, two factors are introduced in the study. One is called damping factor to dampen the update amplitude of the posterior ensemble mean to avoid nonrealistic values. The other is called inflation factor to relax the posterior ensemble perturbations close to prior to avoid filter inbreeding problems. The sensitivities of the two factors are studied and their favorable values for the Guantao model are determined. The appropriate observation error and ensemble size were also determined to facilitate the further analysis. This study demonstrated that the data assimilation of both model parameters and states gives a smaller model prediction error but with larger uncertainty while the data assimilation of only model states provides a smaller predictive uncertainty but with a larger model prediction error. Data assimilation in a groundwater flow model will improve model prediction and at the same time make the model converge to the true parameters, which provides a successful base for applications in real time modelling or real time controlling strategies

  4. Groundwater flow associated with coalbed gas production, Ferron Sandstone, east-central Utah

    Science.gov (United States)

    Anna, L.O.

    2003-01-01

    The flow and distribution of water associated with coalbed gas production in the Ferron Sandstone was characterized utilizing a discrete fracture network model and a porous media model. A discrete fracture network model calculated fluid flux through volumes of various scales to determine scale effects, directional bulk permeability, and connectivity. The mean directional permeabilities varied by less than a factor of 6, with the northwest-southeast direction (face cleat direction) as the most conductive. Northwest southeast directed hydrofracture simulations increased permeability in all directions except the northeast-southwest, although the permeability increase was not more than a factor of 3. Cluster analysis showed that the simulated cleat network was very well connected at all simulated scales. For thick coals, the entire cleat network formed one compartment, whereas thin coals formed several compartments. Convex hulls of the compartments confirmed that the directional bulk permeability was nearly isotropic. Volumetric calculations of the Ferron coal indicated that all the water produced to date can be accounted for from the coal cleat porosity system and does not depend on contributions of water from contiguous units.Flow paths, determined from porous media modeling from recharge to discharge, indicate that the three coalbed gas (CBG) fields assessed in this study could have different groundwater chemical compositions as confirmed by geochemical data. Simulated water production from 185 wells from 1993 to 1998 showed that in 1998 the maximum head drawdown from the Drunkards Wash field was more than 365 m, and the cone of depression extended to within a short distance of the Ferron outcrop. Maximum drawdown in the Helper field was 120 m, and the maximum drawdown in the Buzzards Bench field was just over 60 m. The cone of depression for the Helper field was half the size of the Drunkards Wash field, and the cone of depression for the Buzzards Bench field was

  5. Hanford Site Composite Analysis Technical Approach Description: Groundwater

    Energy Technology Data Exchange (ETDEWEB)

    Budge, T. J. [CH2M HILL Plateau Remediation Company, Richland, WA (United States)

    2017-10-02

    The groundwater facet of the revised CA is responsible for generating predicted contaminant concentration values over the entire analysis spatial and temporal domain. These estimates will be used as part of the groundwater pathway dose calculation facet to estimate dose for exposure scenarios. Based on the analysis of existing models and available information, the P2R Model was selected as the numerical simulator to provide these estimates over the 10,000-year temporal domain of the CA. The P2R Model will use inputs from initial plume distributions, updated for a start date of 1/1/2017, and inputs from the vadose zone facet, created by a tool under development as part of the ICF, to produce estimates of hydraulic head, transmissivity, and contaminant concentration over time. A recommendation of acquiring 12 computer processors and 2 TB of hard drive space is made to ensure that the work can be completed within the anticipated schedule of the revised CA.

  6. Model Refinement and Simulation of Groundwater Flow in Clinton, Eaton, and Ingham Counties, Michigan

    Science.gov (United States)

    Luukkonen, Carol L.

    2010-01-01

    A groundwater-flow model that was constructed in 1996 of the Saginaw aquifer was refined to better represent the regional hydrologic system in the Tri-County region, which consists of Clinton, Eaton, and Ingham Counties, Michigan. With increasing demand for groundwater, the need to manage withdrawals from the Saginaw aquifer has become more important, and the 1996 model could not adequately address issues of water quality and quantity. An updated model was needed to better address potential effects of drought, locally high water demands, reduction of recharge by impervious surfaces, and issues affecting water quality, such as contaminant sources, on water resources and the selection of pumping rates and locations. The refinement of the groundwater-flow model allows simulations to address these issues of water quantity and quality and provides communities with a tool that will enable them to better plan for expansion and protection of their groundwater-supply systems. Model refinement included representation of the system under steady-state and transient conditions, adjustments to the estimated regional groundwater-recharge rates to account for both temporal and spatial differences, adjustments to the representation and hydraulic characteristics of the glacial deposits and Saginaw Formation, and updates to groundwater-withdrawal rates to reflect changes from the early 1900s to 2005. Simulations included steady-state conditions (in which stresses remained constant and changes in storage were not included) and transient conditions (in which stresses changed in annual and monthly time scales and changes in storage within the system were included). These simulations included investigation of the potential effects of reduced recharge due to impervious areas or to low-rainfall/drought conditions, delineation of contributing areas with recent pumping rates, and optimization of pumping subject to various quantity and quality constraints. Simulation results indicate

  7. Understanding Land Use Impacts on Groundwater Quality Using Chemical Analysis

    Science.gov (United States)

    Nitka, A.; Masarik, K.; Masterpole, D.; Johnson, B.; Piette, S.

    2017-12-01

    Chippewa County, in western Wisconsin, has a unique historical set of groundwater quality data. The county conducted extensive groundwater sampling of private wells in 1985 (715 wells) and 2007 (800 wells). In 2016, they collaborated with UW-Extension and UW-Stevens Point to evaluate the current status of groundwater quality in Chippewa County by sampling of as many of the previously studied wells as possible. Nitrate was a primary focus of this groundwater quality inventory. Of the 744 samples collected, 60 were further analyzed for chemical indicators of agricultural and septic waste, two major sources of nitrate contamination. Wells for nitrate source analysis were selected from the 2016 participants based upon certain criteria. Only wells with a Wisconsin Unique Well Number were considered to ensure well construction information was available. Next, an Inverse Distance Weighting tool in ESRI ArcMap was used to assign values categorizing septic density. Two-thirds of the wells were selected in higher density areas and one-third in lower density areas. Equally prioritized was an even distribution of nitrate - N concentrations, with 28 of the wells having nitrate - N concentrations higher than the drinking water standard of 10 mg/L and 32 wells with concentrations between 2 and 10 mg/L. All wells with WUWN and nitrate - N concentrations greater than 20 mg/L were selected. The results of the nitrate source analyses will aid in determining temporal changes and spatial relationships of groundwater quality to soils, geology and land use in Chippewa County.

  8. Fracture network model of the groundwater flow in the Romuvaara site

    International Nuclear Information System (INIS)

    Poteri, A.; Laitinen, M.

    1997-01-01

    In the study, computer codes are employed to analyse the groundwater flow patterns in the sparcely fractured intact rock at the Romuvaara site. The new fracture data gathered during the detailed site characterisation phase demonstrated that the characteristic properties of fractures can be estimated quite reliably from few boreholes and outcrops. Results obtained by employing new methods, like the use of borehole-TV, changed the fracture intensity of the potential water conducting fractures compared to the earlier model. In the preliminary site investigation phase only the orientated fractures were used to derive the parameters of the intact rock. In the present model all the fractures outside the known fracture zones are used. The hydraulic conductivity tensor of the intact rock was estimated with the fracture network model. The flow simulations were calculated for a 16 x 16 x 16 m 3 rock volume and about 2000 fractures. The flow rate distribution through the cross sectional area of the disposal canisters was calculated for a set of ten realisations and a large number of different canister positions. The total number of canister positions simulated was 2200. The flow distribution in larger volume was studied using a method that searched the flow routes of highest conductance. The flow routes were examined into north-south, east-west and vertical directions. Flow routes along homogeneous and heterogeneous fractures were compared. (21 refs.)

  9. Considerations of a nonhomogeneous fluid in the deep groundwater flow system at Hanford

    International Nuclear Information System (INIS)

    Nelson, R.W.

    1988-11-01

    This report presents such a general theory capable of describing the flow on nonhomogeneous fluids in porous media, theory that is a composite from several disciplines including groundwater hydrology, soil physics, civil engineering, petroleum reservoir engineering, mechanics, and mathematical physics. The report discussed the conceptual basis for considering the flow of nonhomogeneous fluids. From this conceptual basis emphasis shifts to providing complete definitions and then appropriately describing those definitions in mathematical terms. Throughout the report, the necessary assumptions are stated in detail because the limitations of any theory are best assessed through careful scrutiny of the assumptions. From the mathematical definitions with appropriate functional dependence the results and constraints needed are derived to provide the general theory necessary to describe the flow of nonhomogeneous fluids in porous media. Particular attention is given to comparing the general theory with the classical theory of flow for a homogeneous fluid. Such comparison provides significant insight to the effects of variable fluid properties on subsurface flow systems. The comparisons also indicate the importance of carefully formulating subsurface flow models within the more general theoretical framework describing the flow of nonhomogeneous fluids in porous media. 29 refs.; 6 figs.; 1 tab

  10. Multivariate analysis of groundwater quality in parts of Lagos - Nigeria

    African Journals Online (AJOL)

    The co-efficient of variation shows that all the groundwater parameters examined are highly variable except pH (10.92%).The factor analysis employed indicates that of the two Factors I and II, Factor I, which explains 62.73% of the total variance, has a strong positive loading on EC, TDS, TH, Na, Cl, Ca, K and SO4 . Factor II ...

  11. Using noble gas tracers to constrain a groundwater flow model with recharge elevations: A novel approach for mountainous terrain

    Science.gov (United States)

    Doyle, Jessica M.; Gleeson, Tom; Manning, Andrew H.; Mayer, K. Ulrich

    2015-01-01

    Environmental tracers provide information on groundwater age, recharge conditions, and flow processes which can be helpful for evaluating groundwater sustainability and vulnerability. Dissolved noble gas data have proven particularly useful in mountainous terrain because they can be used to determine recharge elevation. However, tracer-derived recharge elevations have not been utilized as calibration targets for numerical groundwater flow models. Herein, we constrain and calibrate a regional groundwater flow model with noble-gas-derived recharge elevations for the first time. Tritium and noble gas tracer results improved the site conceptual model by identifying a previously uncertain contribution of mountain block recharge from the Coast Mountains to an alluvial coastal aquifer in humid southwestern British Columbia. The revised conceptual model was integrated into a three-dimensional numerical groundwater flow model and calibrated to hydraulic head data in addition to recharge elevations estimated from noble gas recharge temperatures. Recharge elevations proved to be imperative for constraining hydraulic conductivity, recharge location, and bedrock geometry, and thus minimizing model nonuniqueness. Results indicate that 45% of recharge to the aquifer is mountain block recharge. A similar match between measured and modeled heads was achieved in a second numerical model that excludes the mountain block (no mountain block recharge), demonstrating that hydraulic head data alone are incapable of quantifying mountain block recharge. This result has significant implications for understanding and managing source water protection in recharge areas, potential effects of climate change, the overall water budget, and ultimately ensuring groundwater sustainability.

  12. Analysis and determination of age of oil spills in soil and groundwater

    International Nuclear Information System (INIS)

    Hoedl, P.; Schindlbauer, H.

    1995-01-01

    The extensive searching for hydrocarbon-based spills in soil and groundwater during the last few years rises the question of whom caused these contaminations. The answer to this very specific question is not easy and often requires the exact determination of age of the contamination. Therefore, the sampling of all imaginable data around the spilled material is necessary. Beginning at the precise check-up of the geological surrounding, including the definition of the condition and construction of the soil as well as the determination of the flow-direction of the groundwater, the chemical analysis should describe the containing substances and/or the products in the best possible way. Summing all these data and taking into consideration of the well-known microbiological pathways of decomposition for one- and/or a group of substances, it should be possible to determine the age of a contamination. (orig.) [de

  13. PHAST Version 2-A Program for Simulating Groundwater Flow, Solute Transport, and Multicomponent Geochemical Reactions

    Science.gov (United States)

    Parkhurst, David L.; Kipp, Kenneth L.; Charlton, Scott R.

    2010-01-01

    The computer program PHAST (PHREEQC And HST3D) simulates multicomponent, reactive solute transport in three-dimensional saturated groundwater flow systems. PHAST is a versatile groundwater flow and solute-transport simulator with capabilities to model a wide range of equilibrium and kinetic geochemical reactions. The flow and transport calculations are based on a modified version of HST3D that is restricted to constant fluid density and constant temperature. The geochemical reactions are simulated with the geochemical model PHREEQC, which is embedded in PHAST. Major enhancements in PHAST Version 2 allow spatial data to be defined in a combination of map and grid coordinate systems, independent of a specific model grid (without node-by-node input). At run time, aquifer properties are interpolated from the spatial data to the model grid; regridding requires only redefinition of the grid without modification of the spatial data. PHAST is applicable to the study of natural and contaminated groundwater systems at a variety of scales ranging from laboratory experiments to local and regional field scales. PHAST can be used in studies of migration of nutrients, inorganic and organic contaminants, and radionuclides; in projects such as aquifer storage and recovery or engineered remediation; and in investigations of the natural rock/water interactions in aquifers. PHAST is not appropriate for unsaturated-zone flow, multiphase flow, or density-dependent flow. A variety of boundary conditions are available in PHAST to simulate flow and transport, including specified-head, flux (specified-flux), and leaky (head-dependent) conditions, as well as the special cases of rivers, drains, and wells. Chemical reactions in PHAST include (1) homogeneous equilibria using an ion-association or Pitzer specific interaction thermodynamic model; (2) heterogeneous equilibria between the aqueous solution and minerals, ion exchange sites, surface complexation sites, solid solutions, and gases; and

  14. Ground-Water Flow Model for the Spokane Valley-Rathdrum Prairie Aquifer, Spokane County, Washington, and Bonner and Kootenai Counties, Idaho

    Science.gov (United States)

    Hsieh, Paul A.; Barber, Michael E.; Contor, Bryce A.; Hossain, Md. Akram; Johnson, Gary S.; Jones, Joseph L.; Wylie, Allan H.

    2007-01-01

    This report presents a computer model of ground-water flow in the Spokane Valley-Rathdrum Prairie (SVRP) aquifer in Spokane County, Washington, and Bonner and Kootenai Counties, Idaho. The aquifer is the sole source of drinking water for more than 500,000 residents in the area. In response to the concerns about the impacts of increased ground-water withdrawals resulting from recent and projected urban growth, a comprehensive study was initiated by the Idaho Department of Water Resources, the Washington Department of Ecology, and the U.S. Geological Survey to improve the understanding of ground-water flow in the aquifer and of the interaction between ground water and surface water. The ground-water flow model presented in this report is one component of this comprehensive study. The primary purpose of the model is to serve as a tool for analyzing aquifer inflows and outflows, simulating the effects of future changes in ground-water withdrawals from the aquifer, and evaluating aquifer management strategies. The scale of the model and the level of detail are intended for analysis of aquifer-wide water-supply issues. The SVRP aquifer model was developed by the Modeling Team formed within the comprehensive study. The Modeling Team consisted of staff and personnel working under contract with the Idaho Department of Water Resources, personnel working under contract with the Washington Department of Ecology, and staff of the U.S. Geological Survey. To arrive at a final model that has the endorsement of all team members, decisions on modeling approach, methodology, assumptions, and interpretations were reached by consensus. The ground-water flow model MODFLOW-2000 was used to simulate ground-water flow in the SVPR aquifer. The finite-difference model grid consists of 172 rows, 256 columns, and 3 layers. Ground-water flow was simulated from September 1990 through September 2005 using 181 stress periods of 1 month each. The areal extent of the model encompasses an area of

  15. Technical know-how for modeling of geological environment. (1) Overview and groundwater flow modeling

    International Nuclear Information System (INIS)

    Saegusa, Hiromitsu; Takeuchi, Shinji; Maekawa, Keisuke; Osawa, Hideaki; Semba, Takeshi

    2011-01-01

    It is important for site characterization projects to manage the decision-making process with transparency and traceability and to transfer the technical know-how accumulated during the research and development to the implementing phase and to future generations. The modeling for a geological environment is to be used to synthesize investigation results. Evaluation of the impact of uncertainties in the model is important to identify and prioritize key issues for further investigations. Therefore, a plan for site characterization should be made based on the results of the modeling. The aim of this study is to support for the planning of initial surface-based site characterization based on the technical know-how accumulated from the Mizunami Underground Research Laboratory Project and the Horonobe Underground Research Laboratory Project. These projects are broad scientific studies of the deep geological environment that are a basis for research and development for the geological disposal of high-level radioactive wastes. In this study, the work-flow of the groundwater flow modeling, which is one of the geological environment models, and is to be used for setting the area for the geological environment modeling and for groundwater flow characterization, and the related decision-making process using literature data have been summarized. (author)

  16. Prediction of Groundwater Flow and Transport Processes in an Urban Area: A Combined Approach of Field Testing and Numerical Modeling

    Science.gov (United States)

    Popp, Andrea; Moeck, Christian; Radny, Dirk; Borer, Paul; Affolter, Annette; Epting, Jannis; Huggenberger, Peter; Auckenthaler, Adrian; Schirmer, Mario

    2015-04-01

    Drinking water supply in urban areas is challenging due to different kinds of water use and potential groundwater contamination. We investigate an area where drinking water production is close to different contaminated sites. The study site is characterized by a high complexity of the tectonic and geological setting with a gravel and a karstic aquifer. The two aquifers are partly connected, partly disconnected by an aquitard. To avoid drinking water contamination, artificial groundwater recharge with surface water into the gravel aquifer is used to create a hydraulic barrier between the contaminated sites and the water abstraction wells. Trace compounds, that were found in former times in the surface water but not nowadays, are still detected in the extracted drinking water. Different studies have been performed such as numerical modeling, intensive groundwater monitoring and investigation of drilling cores to get a differentiated overview of the distribution of the contaminants. Back-diffusion from the matrix due to changing hydraulic boundary was stated to be the reason for the actual distribution of the contaminants. In a first approach due to the lack of experimental data or evidence from field measurements, the permeabilities of the karstic aquifer were assumed as homogeneous. In our study, we seek to identify the flow and transport processes within the system including the fracture network in a combined approach of field work and 3D modeling with FEFLOW. During a field campaign we acquired water samples for the analysis of stable water isotopes as well as organic and inorganic compounds. Furthermore, tritium and helium samples were taken to estimate water ages and to determine the flow through the fracture networks. A combination of existing and recently obtained data was used to build and validate a 3D flow and transport model. The simulation of different scenarios such as the water flow for varying injection and extraction rates as well as particle

  17. Combined geophysical techniques for detailed groundwater flow investigation in tectonically deformed fractured rocks

    OpenAIRE

    John Alexopoulos; Emmanuel Vassilakis; Spyridon Dilalos

    2014-01-01

    In this paper we present a combination of several near surface geophysical investigation techniques with high resolution remote sensing image interpretations, in order to define the groundwater flow paths and whether they can be affected by future seismic events. A seasonal spring (Amvrakia) located at the foot of Meteora pillars near the village of Kastraki (Greece) was chosen as a test site. The Meteora conglomeratic formations crop out throughout the study area and are characterized by lar...

  18. Numerical simulations of groundwater flow and solute transport in the Lake 233 aquifer

    International Nuclear Information System (INIS)

    Klukas, M.H.; Moltyaner, G.L.

    1995-05-01

    A three-dimensional numerical flow model of the Lake 233 aquifer underlying the site of the proposed Intrusion Resistant Underground Structure (IRUS) for low level waste disposal is developed. A reference hydraulic conductivity distribution incorporating the key stratigraphic units and field estimates of recharge from Lake 233 are used as model input. The model was calibrated against the measured hydraulic head distribution, the flowpath of a historic 90 Sr plume in the aquifer and measured groundwater velocities. (author). 23 refs., 4 tabs., 31 figs

  19. MODELING OF RELATIONSHIP BETWEEN GROUNDWATER FLOW AND OTHER METEOROLOGICAL VARIABLES USING FUZZY LOGIC

    Directory of Open Access Journals (Sweden)

    Şaban YURTÇU

    2006-02-01

    Full Text Available In this study, modeling of the effect of rainfall, flow and evaporation as independent variables on the change of underground water levels as dependent variables were investigated by fuzzy logic (FL. In the study, total 396 values taken from six observation stations belong to Afyon inferior basin in Akarçay from 1977 to 1989 years were used. Using the monthly average values of stations, the change of underground water level was modeled by FL. It is observed that the results obtained from FL and the observations are compatible with each other. This shows FL modeling can be used to estimate groundwater levels from the appropriate meteorological value.

  20. Mechanism and rate of denitrification in an agricultural watershed: Electron and mass balance along groundwater flow paths

    Science.gov (United States)

    Tesoriero, Anthony J.; Liebscher, Hugh; Cox, Stephen E.

    2000-01-01

    The rate and mechanism of nitrate removal along and between groundwater flow paths were investigated using a series of well nests screened in an unconfined sand and gravel aquifer. Intensive agricultural activity in this area has resulted in nitrate concentrations in groundwater often exceeding drinking water standards. Both the extent and rate of denitrification varied depending on the groundwater flow path. While little or no denitrification occurred in much of the upland portions of the aquifer, a gradual redox gradient is observed as aerobic upland groundwater moves deeper in the aquifer. In contrast, a sharp shallow redox gradient is observed adjacent to a third‐order stream as aerobic groundwater enters reduced sediments. An essentially complete loss of nitrate concurrent with increases in excess N2 provide evidence that denitrification occurs as groundwater enters this zone. Electron and mass balance calculations suggest that iron sulfide (e.g., pyrite) oxidation is the primary source of electrons for denitrification. Denitrification rate estimates were based on mass balance calculations using nitrate and excess N2 coupled with groundwater travel times. Travel times were determined using a groundwater flow model and were constrained by chlorofluorocarbon‐based age dates. Denitrification rates were found to vary considerably between the two areas where denitrification occurs. Denitrification rates in the deep, upland portions of the aquifer were found to range from from 1.0 to 2.7 mM of N per year. Potential denitrification rates in groundwater adjacent to the stream may be much faster, with rates up to 140 mM per year based on an in situ experiment conducted in this zone.

  1. URANIUM-SERIES CONSTRAINTS ON RADIONUCLIDE TRANSPORT AND GROUNDWATER FLOW AT NOPAL I URANIUM DEPOSIT, SIERRA PENA BLANCA, MEXICO

    Energy Technology Data Exchange (ETDEWEB)

    S. J. Goldstein, S. Luo, T. L. Ku, and M. T. Murrell

    2006-04-01

    Uranium-series data for groundwater samples from the vicinity of the Nopal I uranium ore deposit are used to place constraints on radionuclide transport and hydrologic processes at this site, and also, by analogy, at Yucca Mountain. Decreasing uranium concentrations for wells drilled in 2003 suggest that groundwater flow rates are low (< 10 m/yr). Field tests, well productivity, and uranium isotopic constraints also suggest that groundwater flow and mixing is limited at this site. The uranium isotopic systematics for water collected in the mine adit are consistent with longer rock-water interaction times and higher uranium dissolution rates at the front of the adit where the deposit is located. Short-lived nuclide data for groundwater wells are used to calculate retardation factors that are on the order of 1,000 for radium and 10,000 to 10,000,000 for lead and polonium. Radium has enhanced mobility in adit water and fractures near the deposit.

  2. Hydrogeological Framework Model for Dhaka Regional Groundwater Flow System (DGFS), Bangladesh

    Science.gov (United States)

    Firoz, Abm; Marandi, Andres; Schüth, Christoph; Ribbe, Lars

    2017-04-01

    The hydrogeology of the Dhaka Regional Groundwater Flow System (DGFS) is located in central Bangladesh, consisting of sediment accumulates from the Ganges and Brahmaputra Meghna (GBM) river systems. The DGFS system is stratigraphically and structurally complex and subjected to a variety of structural disruption. These sediment deposits form a complex, three-dimensional (3D) framework that can be subdivided into aquifers and confining units on the basis of their ability to store and transmit water. The aquifer systems in this region are geologically controlled and depend on the sedimentary characteristics of the depositional environment and related parameters. More than 20 years of ground-water flow modeling of the DGFS has produced a succession of models that represent the regional hydrogeology and groundwater flow system. However, incorporation of a geologic framework in the models with different geologic data sets or subsurface interpretation is often missing. Therefore, such incorporation of geological and sedimentological information within the modeling framework could increase model calibration. The separate geological structure of the Dhaka region is studied yet detailed spatial and depth variables of geological and sedimentological information is still not evident in the hydrogeological framework. In this background, the objective of the paper is therefore to incorporate the geological information into the hydrogeological framework model and advance the approach of hydrogeology for the DGFS. We have used the concept of the Hydrogeologic Unit (HGU) - the sediment and deposits formation of the hydrostratigraphic framework for a groundwater flow system. The quaternary sedimentation processes of DGFS were subdivided into different cycles based on sea-level changes and Carbon-14 dating. The subdivisions are called 1a, 1b, 2 and 3 which correspond to high stand fluvial sequences (10-0 ka BP), Transgressive Tract/ low stand (20-10 ka BP), pre lows stand deposits

  3. Analyses of surface and groundwater flow characteristics of the Ljubljana moor and water resources vulnerability to climate and land use change and groundwater overdraft

    Science.gov (United States)

    Globevnik, Lidija; Bracic Zeleznik, Branka

    2016-04-01

    One of the biggest water resource of Slovenian capital is groundwater of Ljubljana moor (Ljubljansko barje) aquifer. Quantity and quality of groundwater in Ljubljana moor aquifer directly depend on precipitation, surface water and riparian ecosystems of the Moor and indirectly by groundwater recharge from higher-lying mountainous karstic areas of forests and grasslands. Maintaining high groundwater level of the Ljubljana moor not only sustain stable water balance of aquifer, but also its riparian and wetland character. It also inhibit larger subsidence of the terrain. The paper addresses the vulnerability of the Ljubljana moor water resources to climate and land use change and due to groundwater overdraft. The results should help in selecting suitable mitigation measures and management of the Ljubljana moor area. We analyze surface and groundwater flow characteristics of water recharge area of one water work on the Ljubljana moor (Brest) from the point of view of climate change, changes in land use and water pumping practices. The I\\vska River, a tributary to the Ljubljanica River, recharges the area in the gravel bar, which lies just below the hills. We use existing data of meteorological, hydrological and hydrogeological monitoring and simulate rainfall-runoff processes. We use a conceptual semi-distributed rainfall-runoff model HBV-Light and simulate hydrological characteristics of the Ljubljana Moor (groundwater level fluctuations and recharge, surface - groundwater interchange) with two hydrodynamic models, DHI MIKE FLOOD (surface flow, 2D simulation) and DHI MIKE SHE (groundwater flow). For a calibration of runoff model HBV Light and MIKE SHE we use measured daily discharge data of the river I\\vska (1970-2010) and groundwater level data along the river (2010-2013) respectively. In groundwater modelling, we include the data of water pumping. Daily precipitation and temperature for period 2020 - 2050 are from ESAMBLE project for two GCM climate scenarios. We

  4. Hydrogeochemical analysis and quality evaluation of groundwater ...

    African Journals Online (AJOL)

    The chemical analysis revealed that the total hardness (measured in terms of CaCO3) varied from 16 to 140 mg/l for both sets of samples indicating soft to moderately hard water. Based on the values of EC, percent sodium, SAR (which vary from 0.3 to 1.7 meq/l), RSC (from 0.1 to 0.99 meq/l less than the standard value of ...

  5. Three-dimensional model for multi-component reactive transport with variable density groundwater flow

    Science.gov (United States)

    Mao, X.; Prommer, H.; Barry, D.A.; Langevin, C.D.; Panteleit, B.; Li, L.

    2006-01-01

    PHWAT is a new model that couples a geochemical reaction model (PHREEQC-2) with a density-dependent groundwater flow and solute transport model (SEAWAT) using the split-operator approach. PHWAT was developed to simulate multi-component reactive transport in variable density groundwater flow. Fluid density in PHWAT depends not on only the concentration of a single species as in SEAWAT, but also the concentrations of other dissolved chemicals that can be subject to reactive processes. Simulation results of PHWAT and PHREEQC-2 were compared in their predictions of effluent concentration from a column experiment. Both models produced identical results, showing that PHWAT has correctly coupled the sub-packages. PHWAT was then applied to the simulation of a tank experiment in which seawater intrusion was accompanied by cation exchange. The density dependence of the intrusion and the snow-plough effect in the breakthrough curves were reflected in the model simulations, which were in good agreement with the measured breakthrough data. Comparison simulations that, in turn, excluded density effects and reactions allowed us to quantify the marked effect of ignoring these processes. Next, we explored numerical issues involved in the practical application of PHWAT using the example of a dense plume flowing into a tank containing fresh water. It was shown that PHWAT could model physically unstable flow and that numerical instabilities were suppressed. Physical instability developed in the model in accordance with the increase of the modified Rayleigh number for density-dependent flow, in agreement with previous research. ?? 2004 Elsevier Ltd. All rights reserved.

  6. Groundwater flow and solute transport modelling from within R: Development of the RMODFLOW and RMT3DMS packages.

    Science.gov (United States)

    Rogiers, Bart

    2015-04-01

    Since a few years, an increasing number of contributed R packages is becoming available, in the field of hydrology. Hydrological time series analysis packages, lumped conceptual rainfall-runoff models, distributed hydrological models, weather generators, and different calibration and uncertainty estimation methods are all available. Also a few packages are available for solving partial differential equations. Subsurface hydrological modelling is however still seldomly performed in R, or with codes interfaced with R, despite the fact that excellent geostatistical packages, model calibration/inversion options and state-of-the-art visualization libraries are available. Moreover, other popular scientific programming languages like matlab and python have packages for pre- and post-processing files of MODFLOW (Harbaugh 2005) and MT3DMS (Zheng 2010) models. To fill this gap, we present here the development versions of the RMODFLOW and RMT3DMS packages, which allow pre- and post-processing MODFLOW and MT3DMS input and output files from within R. File reading and writing functions are currently available for different packages, and plotting functions are foreseen making use of the ggplot2 package (plotting system based on the grammar of graphics; Wickham 2009). The S3 generic-function object oriented programming style is used for this. An example is provided, making modifications to an existing model, and visualization of the model output. References Harbaugh, A. (2005). MODFLOW-2005: The US Geological Survey Modular Ground-water Model--the Ground-water Flow Process, U.S. Geological Survey Techniques and Methods 6-A16 (p. 253). Wickham, H. (2009). ggplot2: elegant graphics for data analysis. Springer New York, 2009. Zheng, C. (2010). MT3DMS v5.3, a modular three-dimensional multispecies transport model for simulation of advection, dispersion and chemical reactions of contaminants in groundwater systems. Supplemental User's Guide. (p. 56).

  7. Groundwater Flow Model of Göksu Delta Coastal Aquifer System

    Science.gov (United States)

    Erdem Dokuz, Uǧur; Çelik, Mehmet; Arslan, Şebnem; Engin, Hilal

    2016-04-01

    Like many other coastal areas, Göksu Delta (Mersin-Silifke, Southern Turkey) is a preferred place for human settlement especially due to its productive farmlands and water resources. The water dependent ecosystem in Göksu delta hosts about 332 different plant species and 328 different bird species besides serving for human use. Göksu Delta has been declared as Special Environmental Protection Zone, Wildlife Protection Area, and RAMSAR Convention for Wetlands of International Importance area. Unfortunately, rising population, agricultural and industrial activities cause degradation of water resources both by means of quality and quantity. This problem also exists for other wetlands around the world. It is necessary to prepare water management plans by taking global warming issues into account to protect water resources for next generations. To achieve this, the most efficient tool is to come up with groundwater management strategies by constructing groundwater flow models. By this aim, groundwater modeling studies were carried out for Göksu Delta coastal aquifer system. As a first and most important step in all groundwater modeling studies, geological and hydrogeological settings of the study area have been investigated. Göksu Delta, like many other deltaic environments, has a complex structure because it was formed with the sediments transported by Göksu River throughout the Quaternary period and shaped throughout the transgression-regression periods. Both due to this complex structure and the lack of observation wells penetrating deep enough to give an idea of the total thickness of the delta, it was impossible to reveal out the hydrogeological setting in a correct manner. Therefore, six wells were drilled to construct the conceptual hydrogeological model of Göksu Delta coastal aquifer system. On the basis of drilling studies and slug tests that were conducted along Göksu Delta, hydrostratigraphic units of the delta system have been obtained. According to

  8. Recharge and Groundwater Flow Within an Intracratonic Basin, Midwestern United States.

    Science.gov (United States)

    Panno, Samuel V; Askari, Zohreh; Kelly, Walton R; Parris, Thomas M; Hackley, Keith C

    2018-01-01

    The conservative nature of chloride (Cl - ) in groundwater and the abundance of geochemical data from various sources (both published and unpublished) provided a means of developing, for the first time, a representation of the hydrogeology of the Illinois Basin on a basin-wide scale. The creation of Cl - isocons superimposed on plan view maps of selected formations and on cross sections across the Illinois Basin yielded a conceptual model on a basin-wide scale of recharge into, groundwater flow within and through the Illinois Basin. The maps and cross sections reveal the infiltration and movement of freshwater into the basin and dilution of brines within various geologic strata occurring at basin margins and along geologic structures. Cross-formational movement of brines is also seen in the northern part of the basin. The maps and cross sections also show barriers to groundwater movement created by aquitards resulting in areas of apparent isolation/stagnation of concentrated brines within the basin. The distribution of Cl - within the Illinois Basin suggests that the current chemical composition of groundwater and distribution of brines within the basin is dependent on five parameters: (1) presence of bedrock exposures along basin margins; (2) permeability of geologic strata and their distribution relative to one another; (3) presence or absence of major geologic structures; (4) intersection of major waterways with geologic structures, basin margins, and permeable bedrock exposures; and (5) isolation of brines within the basin due to aquitards, inhomogeneous permeability, and, in the case of the deepest part of the basin, brine density effects. © 2017, National Ground Water Association.

  9. Hydrogeologic Settings and Ground-Water Flow Simulations for Regional Studies of the Transport of Anthropogenic and Natural Contaminants to Public-Supply Wells - Studies Begun in 2001

    Science.gov (United States)

    Paschke, Suzanne S.

    2007-01-01

    This study of the Transport of Anthropogenic and Natural Contaminants to public-supply wells (TANC study) is being conducted as part of the U.S. Geological Survey National Water Quality Assessment (NAWQA) Program and was designed to increase understanding of the most important factors to consider in ground-water vulnerability assessments. The seven TANC studies that began in 2001 used retrospective data and ground-water flow models to evaluate hydrogeologic variables that affect aquifer susceptibility and vulnerability at a regional scale. Ground-water flow characteristics, regional water budgets, pumping-well information, and water-quality data were compiled from existing data and used to develop conceptual models of ground-water conditions for each study area. Steady-state regional ground-water flow models were used to represent the conceptual models, and advective particle-tracking simulations were used to compute areas contributing recharge and traveltimes from recharge to selected public-supply wells. Retrospective data and modeling results were tabulated into a relational database for future analysis. Seven study areas were selected to evaluate a range of hydrogeologic settings and management practices across the Nation: the Salt Lake Valley, Utah; the Eagle Valley and Spanish Springs Valley, Nevada; the San Joaquin Valley, California; the Northern Tampa Bay region, Florida; the Pomperaug River Basin, Connecticut; the Great Miami River Basin, Ohio; and the Eastern High Plains, Nebraska. This Professional Paper Chapter presents the hydrogeologic settings and documents the ground-water flow models for each of the NAWQA TANC regional study areas that began work in 2001. Methods used to compile retrospective data, determine contributing areas of public-supply wells, and characterize oxidation-reduction (redox) conditions also are presented. This Professional Paper Chapter provides the foundation for future susceptibility and vulnerability analyses in the TANC

  10. Flows method in global analysis

    International Nuclear Information System (INIS)

    Duong Minh Duc.

    1994-12-01

    We study the gradient flows method for W r,p (M,N) where M and N are Riemannian manifold and r may be less than m/p. We localize some global analysis problem by constructing gradient flows which only change the value of any u in W r,p (M,N) in a local chart of M. (author). 24 refs

  11. Geochemical evidence of groundwater flow paths and the fate and transport of constituents of concern in the alluvial aquifer at Fort Wingate Depot Activity, New Mexico, 2009

    Science.gov (United States)

    Robertson, Andrew J.; Henry, David W.; Langman, Jeffery B.

    2013-01-01

    As part of an environmental investigation at Fort Wingate Depot Activity, New Mexico, the U.S. Geological Survey, in cooperation with the U.S. Army Corps of Engineers, interpreted aqueous geochemical concentrations to better understand the groundwater flow paths and the fate and transport of constituents of concern in the alluvial aquifer underlying the study area. The fine-grained nature of the alluvial matrix creates a highly heterogeneous environment, which adds to the difficulty of characterizing the flow of groundwater and the fate of aqueous constituents of concern. The analysis of the groundwater geochemical data collected in October 2009 provides evidence that is used to identify four groundwater flow paths and their extent in the aquifer and indicates the dominant attenuation processes for the constituents of concern. The extent and interaction of groundwater flow paths were delineated by the major ion concentrations and their relations to each other. Four areas of groundwater recharge to the study area were identified based on groundwater elevations, hydrogeologic characteristics, and geochemical and isotopic evidence. One source of recharge enters the study area from the saturated alluvial deposits underlying the South Fork of the Puerco River to the north of the study area. A second source of recharge is shown to originate from a leaky cistern containing production water from the San Andres-Glorieta aquifer. The other two sources of recharge are shown to enter the study area from the south: one from an arroyo valley draining an area to the south and one from hill-front recharge that passes under the reported release of perchlorate and explosive constituents. The spatial extent and interaction of groundwater originating from these various sources along identified flow paths affect the persistence and attenuation of constituents of concern. It was determined that groundwater originating in the area of a former explosives’ wash-out operation and an

  12. Second status report on regional and local ground-water flow modeling for Richton and Cypress Creek Domes, Mississippi

    International Nuclear Information System (INIS)

    1986-08-01

    Regional and local ground-water flow within the principal geohydrologic units in the Mississippi salt-dome basin is evaluated by developing conceptual models of the flow regime at a regional and a local scale and testing these models using a three-dimensional, finite-difference flow code. Semiquantitative sensitivity analyses (a limited parametric study) are conducted to define the system response to changes in the conceptual models. The conceptual models are described in terms of their areal and vertical discretizations, aquifer properties, fluid properties, and hydrologic boundary conditions. The simulated ground-water flow fields are described with potentiometric surfaces, areas of upward and downward flow across aquitards, tables summarizing the real and vertical volumetric flows through the principal units, and Darcy velocities with specified finite-difference blocks. Ground-water travel paths and times from both Richton Dome and Cypress Creek Dome are provided. The regional scale simulation results are discussed with regard to measured field data. The reported work is the second state of an ongoing evaluation of Richton and Cypress Creek Domes as potential repositories for high-level radioactive wastes. The results and conclusions should thus be considered preliminary and subject to modification with the collection of additional data. However, the report does provide a useful basis for describing the sensitivity of the present conceptualization of ground-water flow to parameterization and, to a lesser extent, the uncertainties in the present conceptualization. 19 refs., 33 figs., 25 tabs

  13. Flow regime analysis of non-Newtonian duct flows

    Science.gov (United States)

    Speetjens, Michel; Rudman, Murray; Metcalfe, Guy

    2006-01-01

    Reoriented duct flows of generalized Newtonian fluids are an idealization of non-Newtonian fluid flow in industrial in-line mixers. Based on scaling analysis and computation we find that non-Newtonian duct flows have several limit behaviors, in the sense that such flows can become (nearly) independent of one or more of the rheological and dynamical control parameters, simplifying the general flow and mixing problem. These limit flows give several levels of modeling complexity to the full problem of non-Newtonian duct flow. We describe the sets of simplified flow models and their corresponding regions of validity. This flow-model decomposition captures the essential rheological and dynamical characteristics of the reoriented duct flows and enables a more efficient and systematic study and design of flow and mixing of non-Newtonian fluids in ducts. Key aspects of the flow-model decomposition are demonstrated via a specific, but representative, duct flow.

  14. Conceptualization of groundwater flow of a coastal arid aquifer using isotopic and chemical tools: La Paz, Baja California Sur, Mexico

    Science.gov (United States)

    Tamez-Melendez, Carol; Hernández-Antonio, Arturo; Mahlknecht, Jürgen

    2016-04-01

    Groundwater from the La Paz coastal aquifer in Baja California Sur, Mexico, is the main source of drinking water for the local population. Due to its proximity to the coast, sea water intrusion is the main factor of salinization of groundwater. Other geochemical processes also affect the quality of the aquifer threating its vulnerability. Forty-seven samples were analyzed for ion chemistry and isotopes. A hierarchical cluster analysis was performed for a better interpretation resulting in three main groups and proved for geographical correspondence. Deuterium and d18O ranged from -82 to -52.1 and from -11.6 to -7 permil, respectively, showing that the main recharge originates in the Sierra el Novillo, flowing toward SE-NW direction and in accordance to deuterium excess (d) high evaporation effects (d>10‰) are mostly in the middle portion of the study area and in El Centenario due to high kinetic isotope fractioning related to elevated temperatures. Hydrogeochemistry analyses demonstrated salinization mainly due to sea water intrusion and in second instance due water-rock interaction, where enrichment of Na+ (ranges from 35.7 to 1089 mg/L-1) was present in some samples probably due to weathering of silicates and/or cation exchange in soils with Ca2+ (27.7 to 658 mg/L-1) at clay-surfaces. High concentrations of NO3-2 (ranges from 1.4 to 48.8 mg/L-1), Cl- (ranges from 54.4 to 2960 mg/L-1) and Na+ show that anthropogenic input is mainly coming from an agricultural area (El Centenario-Chametla) where heavy groundwater extractions are made for irrigational purposes, lowering the groundwater table up to 10 m and consequently promoting upconing and salinity concentrations (NaCl). Carbon-13 and radiocarbon ranged from -12.3 to -9.1‰ and from 29.5 to 100.4 pmC, respectively. Distribution of ages (up to ~5000 years) indicates two flow trends (E-W and SE-NW).

  15. Preliminary site description: Groundwater flow simulations. Simpevarp area (version 1.1) modelled with CONNECTFLOW

    International Nuclear Information System (INIS)

    Hartley, Lee; Worth, David; Gylling, Bjoern; Marsic, Niko; Holmen, Johan

    2004-08-01

    The main objective of this study is to assess the role of known and unknown hydrogeological conditions for the present-day distribution of saline groundwater at the Simpevarp and Laxemar sites. An improved understanding of the paleo-hydrogeology is necessary in order to gain credibility for the Site Descriptive Model in general and the Site Hydrogeological Description in particular. This is to serve as a basis for describing the present hydrogeological conditions as well as predictions of future hydrogeological conditions. This objective implies a testing of: geometrical alternatives in the structural geology and bedrock fracturing, variants in the initial and boundary conditions, and parameter uncertainties (i.e. uncertainties in the hydraulic property assignment). This testing is necessary in order to evaluate the impact on the groundwater flow field of the specified components and to promote proposals of further investigations of the hydrogeological conditions at the site. The general methodology for modelling transient salt transport and groundwater flow using CONNECTFLOW that was developed for Forsmark has been applied successfully also for Simpevarp. Because of time constraints only a key set of variants were performed that focussed on the influences of DFN model parameters, the kinematic porosity, and the initial condition. Salinity data in deep boreholes available at the time of the project was too limited to allow a good calibration exercise. However, the model predictions are compared with the available data from KLX01 and KLX02 below. Once more salinity data is available it may be possible to draw more definite conclusions based on the differences between variants. At the moment though the differences should just be used understand the sensitivity of the models to various input parameters

  16. A proposed strategy for the validation of ground-water flow and solute transport models

    International Nuclear Information System (INIS)

    Davis, P.A.; Goodrich, M.T.

    1991-01-01

    Ground-water flow and transport models can be thought of as a combination of conceptual and mathematical models and the data that characterize a given system. The judgment of the validity or invalidity of a model depends both on the adequacy of the data and the model structure (i.e., the conceptual and mathematical model). This report proposes a validation strategy for testing both components independently. The strategy is based on the philosophy that a model cannot be proven valid, only invalid or not invalid. In addition, the authors believe that a model should not be judged in absence of its intended purpose. Hence, a flow and transport model may be invalid for one purpose but not invalid for another. 9 refs

  17. Inverse modeling and uncertainty analysis of potential groundwater recharge to the confined semi-fossil Ohangwena II Aquifer, Namibia

    Science.gov (United States)

    Wallner, Markus; Houben, Georg; Lohe, Christoph; Quinger, Martin; Himmelsbach, Thomas

    2017-12-01

    The identification of potential recharge areas and estimation of recharge rates to the confined semi-fossil Ohangwena II Aquifer (KOH-2) is crucial for its future sustainable use. The KOH-2 is located within the endorheic transboundary Cuvelai-Etosha-Basin (CEB), shared by Angola and Namibia. The main objective was the development of a strategy to tackle the problem of data scarcity, which is a well-known problem in semi-arid regions. In a first step, conceptual geological cross sections were created to illustrate the possible geological setting of the system. Furthermore, groundwater travel times were estimated by simple hydraulic calculations. A two-dimensional numerical groundwater model was set up to analyze flow patterns and potential recharge zones. The model was optimized against local observations of hydraulic heads and groundwater age. The sensitivity of the model against different boundary conditions and internal structures was tested. Parameter uncertainty and recharge rates were estimated. Results indicate that groundwater recharge to the KOH-2 mainly occurs from the Angolan Highlands in the northeastern part of the CEB. The sensitivity of the groundwater model to different internal structures is relatively small in comparison to changing boundary conditions in the form of influent or effluent streams. Uncertainty analysis underlined previous results, indicating groundwater recharge originating from the Angolan Highlands. The estimated recharge rates are less than 1% of mean yearly precipitation, which are reasonable for semi-arid regions.

  18. Analysis of americium, plutonium and technetium solubility in groundwater

    Energy Technology Data Exchange (ETDEWEB)

    Takeda, Seiji [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

    1999-08-01

    Safety assessments for geologic disposal of radioactive waste generally use solubilities of radioactive elements as the parameter restricting the dissolution of the elements from a waste matrix. This study evaluated americium, plutonium and technetium solubilities under a variety of geochemical conditions using the geochemical model EQ3/6. Thermodynamic data of elements used in the analysis were provided in the JAERI-data base. Chemical properties of both natural groundwater and interstitial water in buffer materials (bentonite and concrete) were investigated to determine the variations in Eh, pH and ligand concentrations (CO{sub 3}{sup 2-}, F{sup -}, PO{sub 4}{sup 3-}, SO{sub 4}{sup 2-}, NO{sub 3}{sup -} and NH{sub 4}{sup +}). These properties can play an important role in the complexation of radioactive elements. Effect of the groundwater chemical properties on the solubility and formation of chemical species for americium, plutonium and technetium was predicted based on the solubility analyses under a variety of geochemical conditions. The solubility and speciation of the radioactive elements were estimated, taking into account the possible range of chemical compositions determined from the groundwater investigation. (author)

  19. Modelling groundwater fractal flow with fractional differentiation via Mittag-Leffler law

    Science.gov (United States)

    Ahokposi, D. P.; Atangana, Abdon; Vermeulen, D. P.

    2017-04-01

    Modelling the flow of groundwater within a network of fractures is perhaps one of the most difficult exercises within the field of geohydrology. This physical problem has attracted the attention of several scientists across the globe. Already two different types of differentiations have been used to attempt modelling this problem including the classical and the fractional differentiation. In this paper, we employed the most recent concept of differentiation based on the non-local and non-singular kernel called the generalized Mittag-Leffler function, to reshape the model of groundwater fractal flow. We presented the existence of positive solution of the new model. Using the fixed-point approach, we established the uniqueness of the positive solution. We solve the new model with three different numerical schemes including implicit, explicit and Crank-Nicholson numerical methods. Experimental data collected from four constant discharge tests conducted in a typical fractured crystalline rock aquifer of the Northern Limb (Bushveld Complex) in the Limpopo Province (South Africa) are compared with the numerical solutions. It is worth noting that the four boreholes (BPAC1, BPAC2, BPAC3, and BPAC4) are located on Faults.

  20. Efficient geostatistical inversion of transient groundwater flow using preconditioned nonlinear conjugate gradients

    Science.gov (United States)

    Klein, Ole; Cirpka, Olaf A.; Bastian, Peter; Ippisch, Olaf

    2017-04-01

    In the geostatistical inverse problem of subsurface hydrology, continuous hydraulic parameter fields, in most cases hydraulic conductivity, are estimated from measurements of dependent variables, such as hydraulic heads, under the assumption that the parameter fields are autocorrelated random space functions. Upon discretization, the continuous fields become large parameter vectors with O (104 -107) elements. While cokriging-like inversion methods have been shown to be efficient for highly resolved parameter fields when the number of measurements is small, they require the calculation of the sensitivity of each measurement with respect to al