WorldWideScience

Sample records for grinds electronic resource

  1. Grinding and polishing instead of sectioning for the tissue samples with a graft: Implications for light and electron microscopy.

    Science.gov (United States)

    Mukhamadiyarov, Rinat A; Sevostyanova, Victoria V; Shishkova, Daria K; Nokhrin, Andrey V; Sidorova, Olga D; Kutikhin, Anton G

    2016-06-01

    A broad use of the graft replacement requires a detailed investigation of the host-graft interaction, including both histological examination and electron microscopy. A high quality sectioning of the host tissue with a graft seems to be complicated; in addition, it is difficult to examine the same tissue area by both of the mentioned microscopy techniques. To solve these problems, we developed a new technique of epoxy resin embedding with the further grinding, polishing, and staining. Graft-containing tissues prepared by grinding and polishing preserved their structure; however, sectioning frequently required the explantation of the graft and led to tissue disintegration. Moreover, stained samples prepared by grinding and polishing may then be assessed by both light microscopy and backscattered scanning electron microscopy. Therefore, grinding and polishing outperform sectioning when applied to the tissues with a graft.

  2. Selection of Electronic Resources.

    Science.gov (United States)

    Weathers, Barbara

    1998-01-01

    Discusses the impact of electronic resources on collection development; selection of CD-ROMs, (platform, speed, video and sound, networking capability, installation and maintenance); selection of laser disks; and Internet evaluation (accuracy of content, authority, objectivity, currency, technical characteristics). Lists Web sites for evaluating…

  3. Electronic Resource Management Systems

    Directory of Open Access Journals (Sweden)

    Mark Ellingsen

    2004-10-01

    Full Text Available Computer applications which deal with electronic resource management (ERM are quite a recent development. They have grown out of the need to manage the burgeoning number of electronic resources particularly electronic journals. Typically, in the early years of e-journal acquisition, library staff provided an easy means of accessing these journals by providing an alphabetical list on a web page. Some went as far as categorising the e-journals by subject and then grouping the journals either on a single web page or by using multiple pages. It didn't take long before it was recognised that it would be more efficient to dynamically generate the pages from a database rather than to continually edit the pages manually. Of course, once the descriptive metadata for an electronic journal was held within a database the next logical step was to provide administrative forms whereby that metadata could be manipulated. This in turn led to demands for incorporating more information and more functionality into the developing application.

  4. Electronic Resource Management and Design

    Science.gov (United States)

    Abrams, Kimberly R.

    2015-01-01

    We have now reached a tipping point at which electronic resources comprise more than half of academic library budgets. Because of the increasing work associated with the ever-increasing number of e-resources, there is a trend to distribute work throughout the library even in the presence of an electronic resources department. In 2013, the author…

  5. Electronic Resource Management and Design

    Science.gov (United States)

    Abrams, Kimberly R.

    2015-01-01

    We have now reached a tipping point at which electronic resources comprise more than half of academic library budgets. Because of the increasing work associated with the ever-increasing number of e-resources, there is a trend to distribute work throughout the library even in the presence of an electronic resources department. In 2013, the author…

  6. Changes in the aromatic profile of espresso coffee as a function of the grinding grade and extraction time: a study by the electronic nose system.

    Science.gov (United States)

    Severini, C; Ricci, I; Marone, M; Derossi, A; De Pilli, T

    2015-03-01

    The changes in chemical attributes and aromatic profile of espresso coffee (EC) were studied taking into account the extraction time and grinding level as independent variables. Particularly, using an electronic nose system, the changes of the global aromatic profile of EC were highlighted. The results shown as the major amounts of organic acids, solids, and caffeine were extracted in the first 8 s of percolation. The grinding grade significantly affected the quality of EC probably as an effect of the particle size distribution and the percolation pathways of water through the coffee cake. The use of an electronic nose system allowed us to discriminate the fractions of the brew as a function of the percolation time and also the regular coffee obtained from different grinding grades. Particularly, the aromatic profile of a regular coffee (25 mL) was significantly affected by the grinding level of the coffee grounds and percolation time, which are two variables under the control of the bar operator.

  7. Managing electronic resources a LITA guide

    CERN Document Server

    Weir, Ryan O

    2012-01-01

    Informative, useful, current, Managing Electronic Resources: A LITA Guide shows how to successfully manage time, resources, and relationships with vendors and staff to ensure personal, professional, and institutional success.

  8. Electron spin resonance and thermoluminescence in powder form of clear fused quartz: effects of grinding

    CERN Document Server

    Ranjbar, A H; Randle, K

    1999-01-01

    Clear fused quartz (CFQ) tubes were powdered either manually by using a mortar and pestle (for coarse production) or mechanically, using a micronising mill (for fine production). A high and multisignal electron spin resonance (ESR) background was found in the fine powder even after annealing it at 900 deg. C for 20 min. In the case of the coarse powder, the signal (ESR background) varied inversely with particle size and was quite high for particle sizes lower than 38 mu m. In a subsidiary experiment, using fine SiO sub 2 powder (99.8% pure, with the particle size of approx 0.007 mu m), manufactured by using flame hydrolysis, only a weak background signal was found. The sup 6 sup 0 Co gamma-ray irradiated powders (approx 22 Gy) were subjected to ESR analysis or thermoluminescence (TL) readout. The ESR intensity of the coarse powder varied directly with particle size. Thus, the intensity for a particle size of 20-38 mu m was very low and almost the same as the unirradiated intensity. In TL readout the results w...

  9. Electronic Resources Management Project Presentation 2012

    KAUST Repository

    Ramli, Rindra M.

    2012-11-05

    This presentation describes the electronic resources management project undertaken by the KAUST library. The objectives of this project is to migrate information from MS Sharepoint to Millennium ERM module. One of the advantages of this migration is to consolidate all electronic resources into a single and centralized location. This would allow for better information sharing among library staff.

  10. Implementing CORAL: An Electronic Resource Management System

    Science.gov (United States)

    Whitfield, Sharon

    2011-01-01

    A 2010 electronic resource management survey conducted by Maria Collins of North Carolina State University and Jill E. Grogg of University of Alabama Libraries found that the top six electronic resources management priorities included workflow management, communications management, license management, statistics management, administrative…

  11. Implementing CORAL: An Electronic Resource Management System

    Science.gov (United States)

    Whitfield, Sharon

    2011-01-01

    A 2010 electronic resource management survey conducted by Maria Collins of North Carolina State University and Jill E. Grogg of University of Alabama Libraries found that the top six electronic resources management priorities included workflow management, communications management, license management, statistics management, administrative…

  12. Resource Letter: TE-1: Teaching electronics

    Science.gov (United States)

    Henry, Dennis C.

    2002-01-01

    This Resource Letter examines the evolution, roles, and content of courses in electronics in the undergraduate physics curriculum, and provides a guide to resources for faculty teaching such courses. It concludes with a brief section addressing problems of electromagnetic interference in electronic systems, and provides an introduction to the literature and practice of electromagnetic compatibility. I have included textbooks, reference books, articles, collections of laboratory experiments and projects, sources of equipment and parts, software packages, videos, and websites.

  13. Electronic Resources Management System: Recommendation Report 2017

    KAUST Repository

    Ramli, Rindra M.

    2017-05-01

    This recommendation report provides an overview of the selection process for the new Electronic Resources Management System. The library has decided to move away from Innovative Interfaces Millennium ERM module. The library reviewed 3 system as potential replacements namely: Proquest 360 Resource Manager, Ex Libris Alma and Open Source CORAL ERMS. After comparing and trialling the systems, it was decided to go for Proquest 360 Resource Manager.

  14. GRINDING OF DOUBLE DISC GRINDING MACHINE

    Institute of Scientific and Technical Information of China (English)

    Hu Huiqing

    2005-01-01

    The grinding of two parallel sides of a component is accomplished with the accuracy and higher productivity by passing a blank through the truncated cone shape grinders, which are turned angles. The machine is designated by the name of double disc grinding machine (DDGM). Usually, it is used in the mass production. The relationship between these angles, the accuracy, productivity,allowance and parameters of the machine and technology is explained in detail by math, such as vector analysis, transformation of 3D space coordinates, etc. Therefore, in the aspects of qualitative and quantitative analyses, the grinding potential of DDGM is enormous increased and superior to conventional methods. Furthermore, the theoretical foundation of DDGM grinding design and technology is provided to improve, to expand and to create for future. The established machine design and practical experience of grinding technology will get great benefit by them.

  15. Library Training to Promote Electronic Resource Usage

    DEFF Research Database (Denmark)

    Frandsen, Tove Faber; Tibyampansha, Dativa; Ibrahim, Glory

    2017-01-01

    Purpose: Increasing the usage of electronic resources is an issue of concern for many libraries all over the world. Several studies stress the importance of information literacy and instruction in order to increase the usage. Design/methodology/approach: The present article presents the results...

  16. Reviewing the Electronic Resources & Libraries Conference

    Science.gov (United States)

    Tijerina, Bonnie

    2008-01-01

    The third Electronic Resources & Libraries (ER&L) conference gathered at Georgia Institute of Technology's Global Learning and Conference Center in Atlanta, Georgia, March 18-21, 2008. Over 360 attendees, from six countries and from 80% of the United States, represented their libraries and organizations resulting in a diverse and…

  17. Comparison of Grinding Characteristics of Converter Steel Slag with and without Pretreatment and Grinding Aids

    Directory of Open Access Journals (Sweden)

    Jihui Zhao

    2016-10-01

    Full Text Available The converter steel slag cannot be widely used in building materials for its poor grindability. In this paper, the grinding characteristics of untreated and pretreated (i.e., magnetic separation steel slag were compared. Additionally, the grinding property of pretreated steel slag was also studied after adding grinding aids. The results show that the residues (i.e., oversize substance that passed a 0.9 mm square-hole screen can be considered as the hardly grinding phases (HGP and its proportion is about 1.5%. After the initial 20 min grinding, the RO phase (RO phase is a continuous solid solution which is composed of some divalent metal oxides, such as FeO, MgO, MnO, CaO, etc., calcium ferrite, and metallic iron phase made up most of the proportion of the HGP, while the metallic iron made up the most component after 70 min grinding. The D50 of untreated steel slag could only reach 32.89 μm after 50 min grinding, but that of pretreated steel slag could reach 18.16 μm after the same grinding time. The grinding efficiency of steel slag was obviously increased and the particle characteristics were improved after using grinding aids (GA, especially the particle proportions of 3–32 μm were obviously increased by 7.24%, 7.22%, and 10.63% after 40 min, 50 min, and 60 min grinding, respectively. This is mainly because of the reduction of agglomeration and this effect of GA was evidenced by SEM (scanning electron microscope images.

  18. Making sense of the electronic resource marketplace: trends in health-related electronic resources.

    Science.gov (United States)

    Blansit, B D; Connor, E

    1999-07-01

    Changes in the practice of medicine and technological developments offer librarians unprecedented opportunities to select and organize electronic resources, use the Web to deliver content throughout the organization, and improve knowledge at the point of need. The confusing array of available products, access routes, and pricing plans makes it difficult to anticipate the needs of users, identify the top resources, budget effectively, make sound collection management decisions, and organize the resources effectively and seamlessly. The electronic resource marketplace requires much vigilance, considerable patience, and continuous evaluation. There are several strategies that librarians can employ to stay ahead of the electronic resource curve, including taking advantage of free trials from publishers; marketing free trials and involving users in evaluating new products; watching and testing products marketed to the clientele; agreeing to beta test new products and services; working with aggregators or republishers; joining vendor advisory boards; benchmarking institutional resources against five to eight competitors; and forming or joining a consortium for group negotiating and purchasing. This article provides a brief snapshot of leading biomedical resources; showcases several libraries that have excelled in identifying, acquiring, and organizing electronic resources; and discusses strategies and trends of potential interest to biomedical librarians, especially those working in hospital settings.

  19. Electronic resource management systems a workflow approach

    CERN Document Server

    Anderson, Elsa K

    2014-01-01

    To get to the bottom of a successful approach to Electronic Resource Management (ERM), Anderson interviewed staff at 11 institutions about their ERM implementations. Among her conclusions, presented in this issue of Library Technology Reports, is that grasping the intricacies of your workflow-analyzing each step to reveal the gaps and problems-at the beginning is crucial to selecting and implementing an ERM. Whether the system will be used to fill a gap, aggregate critical data, or replace a tedious manual process, the best solution for your library depends on factors such as your current soft

  20. STABLE DIAMOND GRINDING

    Directory of Open Access Journals (Sweden)

    Yury Gutsalenko

    2010-06-01

    Full Text Available The paper generalizes on the one hand theory of kinematic-geometrical simulation of grinding processes by means of tools with working part as binding matrix with abrasive grains located in it in random manner, for example diamond grains, and on the other hand practical performance of combined grinding process, based on introduction of additional energy as electric discharges and called by the organization-developer (Kharkov Polytechnic Institute «diamond-spark grinding» as applied to processing by means of diamond wheel. Implementation of diamond-spark grinding technologies on the basis of developed generalized theoretical approach allows to use the tool with prescribed tool-life, moreover to make the most efficient use of it up to full exhausting of tool-life, determined by diamond-bearing thickness. Development is directed forward computer-aided manufacturing.

  1. Grinding Properties of Abandoned Concrete

    Institute of Scientific and Technical Information of China (English)

    ZHENG Fang-yu; WANG Li-jiu; LI Qiang

    2007-01-01

    The grinding properties of abandoned concrete, which consists primarily of hardened cement, limestone aggregate and river sand, are studied. Theoretical models of grinding are used to explain the experimental observation. The results show that 1) The principle disintegration mechanism of hardened cement and river sand is volumetric grinding, although at later stages grinding of cement becomes difficult because of its flaked structure; 2) The limestone grinding process can be divided into two steps. First, volumetric grinding, with an obvious component of surface grinding, followed by primarily surface grinding as the micro-particle content increases; 3) Initially, the principle mechanism of grinding limestone and river sand is volumetric grinding, albeit less efficient grinding than if these components were ground separately, and; 4) After 10 to 20 min of grinding the grinding bottleneck phenomenon appears and after 20 min of grinding the content of micro-particles is large and surface grinding is the main mechanism while the particle size of the mixture is smaller than that of separately ground river sand and cement but bigger than that of separately ground limestone.

  2. Analysis on the grinding quality of palm oil fibers by using combined grinding equipment

    Science.gov (United States)

    Gan, H. L.; Gan, L. M.; Law, H. C.

    2015-12-01

    As known, Malaysia is the second largest palm oil producer worldwide after Indonesia, therefore indicating the abundance of its wastes within the country. The plantation would be seen to increase to at least 5.2 million ha by 2020, and the waste generation would be 50-70 times the plantation. However, the efficiency of bulk density is reduced. This is one of the main reasons of the initiation of this size reduction/ grinding research. With appropriate parameters, grinding will be seen to be helping in enhancing the inter-particle bindings, subsequently increasing the quality of final products. This paper focuses on the grinding quality involving palm oil wastes by using the Scanning Electron Microscope (SEM). The samples would first be ground to powder at varying grinding speed and finally got the randomly chosen particles measured to obtain the size range. The grinding speed was manipulated from 15 Hz to 40 Hz. From the data obtained, it was found the particles fineness increased with increasing grinding speed. In general, the size ranged from 45 μm to about 600 μm, where the finest was recorded at the speed of 40 Hz. It was also found that the binding was not so encouraging at very low speeds. Therefore, the optimum grinding speed for oil palm residues lied in the range of 25 Hz to 30 Hz. However, there were still limitations to be overcome if the accuracy of the image clarity is to be enhanced.

  3. Electronic Resource Management System. Vernetzung von Lizenzinformationen

    Directory of Open Access Journals (Sweden)

    Michaela Selbach

    2014-12-01

    Full Text Available In den letzten zehn Jahren spielen elektronische Ressourcen im Bereich der Erwerbung eine zunehmend wichtige Rolle: Eindeutig lässt sich hier ein Wandel in den Bibliotheken (fort vom reinen Printbestand zu immer größeren E-Only-Beständen feststellen. Die stetig wachsende Menge an E-Ressourcen und deren Heterogenität stellt Bibliotheken vor die Herausforderung, die E-Ressourcen effizient zu verwalten. Nicht nur Bibliotheken, sondern auch verhandlungsführende Institutionen von Konsortial- und Allianzlizenzen benötigen ein geeignetes Instrument zur Verwaltung von Lizenzinformationen, welches den komplexen Anforderungen moderner E-Ressourcen gerecht wird. Die Deutsche Forschungsgemeinschaft (DFG unterstützt ein Projekt des Hochschulbibliothekszentrums des Landes Nordrhein-Westfalen (hbz, der Universitätsbibliothek Freiburg, der Verbundzentrale des Gemeinsamen Bibliotheksverbundes (GBV und der Universitätsbibliothek Frankfurt, in dem ein bundesweit verfügbares Electronic Ressource Managementsystem (ERMS aufgebaut werden soll. Ein solches ERMS soll auf Basis einer zentralen Knowledge Base eine einheitliche Nutzung von Daten zur Lizenzverwaltung elektronischer Ressourcen auf lokaler, regionaler und nationaler Ebene ermöglichen. Statistische Auswertungen, Rechteverwaltung für alle angeschlossenen Bibliotheken, kooperative Datenpflege sowie ein über standardisierte Schnittstellen geführter Datenaustausch stehen bei der Erarbeitung der Anforderungen ebenso im Fokus wie die Entwicklung eines Daten- und Funktionsmodells. In the last few years the importance of electronic resources in library acquisitions has increased significantly. There has been a shift from mere print holdings to both e- and print combinations and even e-only subscriptions. This shift poses a double challenge for libraries: On the one hand they have to provide their e-resource collections to library users in an appealing way, on the other hand they have to manage these

  4. Nitramine Drying & Fine Grinding Facility

    Data.gov (United States)

    Federal Laboratory Consortium — The Nitramine Drying and Fine Grinding Facility provides TACOM-ARDEC with a state-of-the-art facility capable of drying and grinding high explosives (e.g., RDX and...

  5. Utilization of electronic information resources by academic staff at ...

    African Journals Online (AJOL)

    Utilization of electronic information resources by academic staff at Makerere University. ... AFRICAN JOURNALS ONLINE (AJOL) · Journals · Advanced Search ... It examined the academic staff awareness of the resources available, the types ...

  6. Effectiveness Analysis of Electronic Resources at the Hacettepe University

    OpenAIRE

    2011-01-01

    It is important to collect and analyze the usage data of electronic databases and periodicals in order to make policies regarding the composition, improvement and more extensive utilization of electronic resources of libraries. The aim of this study is to investigate how efficiently the full text accessible electronic resources of Hacettepe University Libraries are used. For this purpose the usage data obtained from COUNTER Software regarding the electronic databases to which Hacettepe Univer...

  7. The Study of Analytical Model of Library Electronic Resources Usage-A Case of Medical Electronic Resources

    OpenAIRE

    Chung-Yen Yu; Jiann-Cherng Shieh

    2014-01-01

    With the advents of internet, the importance of electronic resources is growing. Due to the increasing expensiveness of electronic resources, university libraries normally received budgets from parent institutions annually. They necessarily applied effective and systematic methods for decision making in electronic resources purchase or re-subscription. However, there are some difficulties in practices: First of all, libraries are unable to receive user records; second, the COUNTER statistics ...

  8. High Performance Grinding and Advanced Cutting Tools

    CERN Document Server

    Jackson, Mark J

    2013-01-01

    High Performance Grinding and Advanced Cutting Tools discusses the fundamentals and advances in high performance grinding processes, and provides a complete overview of newly-developing areas in the field. Topics covered are grinding tool formulation and structure, grinding wheel design and conditioning and applications using high performance grinding wheels. Also included are heat treatment strategies for grinding tools, using grinding tools for high speed applications, laser-based and diamond dressing techniques, high-efficiency deep grinding, VIPER grinding, and new grinding wheels.

  9. The Role of the Acquisitions Librarian in Electronic Resources Management

    Science.gov (United States)

    Pomerantz, Sarah B.

    2010-01-01

    With the ongoing shift to electronic formats for library resources, acquisitions librarians, like the rest of the profession, must adapt to the rapidly changing landscape of electronic resources by keeping up with trends and mastering new skills related to digital publishing, technology, and licensing. The author sought to know what roles…

  10. Grind hardening process

    CERN Document Server

    Salonitis, Konstantinos

    2015-01-01

    This book presents the grind-hardening process and the main studies published since it was introduced in 1990s.  The modelling of the various aspects of the process, such as the process forces, temperature profile developed, hardness profiles, residual stresses etc. are described in detail. The book is of interest to the research community working with mathematical modeling and optimization of manufacturing processes.

  11. Electronic resources preferred by pediatric hospitalists for clinical care.

    Science.gov (United States)

    Beck, Jimmy B; Tieder, Joel S

    2015-10-01

    There is little research on pediatric hospitalists' use of evidence-based resources. The aim of this study was to determine the electronic resources that pediatric hospitalists prefer. Using a web-based survey, the authors determined hospitalists' preferred electronic resources, as well as their attitudes toward lifelong learning, practice, and experience characteristics. One hundred sixteen hospitalists completed the survey. The most preferred resource for general information, patient handouts, and treatment was UpToDate. Online search engines were ranked second for general information and patient handouts. Pediatric hospitalists tend to utilize less rigorous electronic resources such as UpToDate and Google. These results can set a platform for discussing the quality of resources that pediatric hospitalists use.

  12. Cataloging and Indexing of Electronic Information Resources

    Science.gov (United States)

    2003-04-01

    digital library, but it facilitates the exchange of these objects among digital libraries . METS provides an XML DTD that can point to metadata in other...International Federation of Library Associations and Institutions (IFLA). (2002). Digital Libraries : Metadata Resources. Retrieved May 3, 2002 from the

  13. Adoption and use of electronic information resources by medical ...

    African Journals Online (AJOL)

    ... were analysed with descriptive Statistics(Simple percentage and frequency count). ... for doing assignment, Google search, for personal development, and getting ... major problems encountered when using electronic Information Resources.

  14. Euler European Libraries and Electronic Resources in Mathematical Sciences

    CERN Document Server

    The Euler Project. Karlsruhe

    The European Libraries and Electronic Resources (EULER) Project in Mathematical Sciences provides the EulerService site for searching out "mathematical resources such as books, pre-prints, web-pages, abstracts, proceedings, serials, technical reports preprints) and NetLab (for Internet resources), this outstanding engine is capable of simple, full, and refined searches. It also offers a browse option, which responds to entries in the author, keyword, and title fields. Further information about the Project is provided at the EULER homepage.

  15. Study on Effect of Ultrasonic Vibration on Grinding Force and Surface Quality in Ultrasonic Assisted Micro End Grinding of Silica Glass

    Directory of Open Access Journals (Sweden)

    Zhang Jianhua

    2014-01-01

    Full Text Available Ultrasonic vibration assisted micro end grinding (UAMEG is a promising processing method for micro parts made of hard and brittle materials. First, the influence of ultrasonic assistance on the mechanism of this processing technology is theoretically analyzed. Then, in order to reveal the effects of ultrasonic vibration and grinding parameters on grinding forces and surface quality, contrast grinding tests of silica glass with and without ultrasonic assistance using micro radial electroplated diamond wheel are conducted. The grinding forces are measured using a three-component dynamometer. The surface characteristics are detected using the scanning electron microscope. The experiment results demonstrate that grinding forces are significantly reduced by introducing ultrasonic vibration into conventional micro end grinding (CMEG of silica glass; ultrasonic assistance causes inhibiting effect on variation percentages of tangential grinding force with grinding parameters; ductile machining is easier to be achieved and surface quality is obviously improved due to ultrasonic assistance in UAMEG. Therefore, larger grinding depth and feed rate adopted in UAMEG can lead to the improvement of removal rate and machining efficiency compared with CMEG.

  16. Building an electronic resource collection a practical guide

    CERN Document Server

    Lee, Stuart D

    2004-01-01

    This practical book guides information professionals step-by-step through building and managing an electronic resource collection. It outlines the range of electronic products currently available in abstracting and indexing, bibliographic, and other services and then describes how to effectively select, evaluate and purchase them.

  17. A critical study of high efficiency deep grinding

    CERN Document Server

    Johnstone, I

    2002-01-01

    The recent years, the aerospace industry in particular has embraced and actively pursued the development of stronger high performance materials, namely nickel based superalloys and hardwearing steels. This has resulted in a need for a more efficient method of machining, and this need was answered with the advent of High Efficiency Deep Grinding (HEDG). This relatively new process using Cubic Boron Nitride (CBN) electroplated grinding wheels has been investigated through experimental and theoretical means applied to two widely used materials, M50 bearing steel and IN718 nickel based superalloy. It has been shown that this grinding method using a stiff grinding centre such as the Edgetek 5-axis machine is a viable process. Using a number of experimental designs, produced results which were analysed using a variety of methods including visual assessment, sub-surface microscopy and surface analysis using a Scanning Electron Microscope (SEM), residual stress measurement using X-Ray Diffraction (XRD) techniques, Ba...

  18. Unsteady-State Grinding Technology (II) Experimental Studies of Grinding Forces and Force Ratio

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    As is known to all, grinding force is one of the most important parameters to evaluate the whole process of grinding. Generally, the grinding force is resolved to three component forces, namely, normal grinding force F n, tangential grinding force F t and a component force acting along the direction of longitudinal feed which is usually neglected because of insignificance. The normal grinding force F n has influence upon surface deformation and roughness of workpiece, while the tangential grinding force ...

  19. Why and How to Measure the Use of Electronic Resources

    Directory of Open Access Journals (Sweden)

    Jean Bernon

    2008-11-01

    Full Text Available A complete overview of library activity implies a complete and reliable measurement of the use of both electronic resources and printed materials. This measurement is based on three sets of definitions: document types, use types and user types. There is a common model of definitions for printed materials, but a lot of questions and technical issues remain for electronic resources. In 2006 a French national working group studied these questions. It relied on the COUNTER standard, but found it insufficient and pointed out the need for local tools such as web markers and deep analysis of proxy logs. Within the French national consortium COUPERIN, a new working group is testing ERMS, SUSHI standards, Shibboleth authentication, along with COUNTER standards, to improve the counting of the electronic resources use. At this stage this counting is insufficient and its improvement will be a European challenge for the future.

  20. Access to electronic resources by visually impaired people

    Directory of Open Access Journals (Sweden)

    Jenny Craven

    2003-01-01

    Full Text Available Research into access to electronic resources by visually impaired people undertaken by the Centre for Research in Library and Information Management has not only explored the accessibility of websites and levels of awareness in providing websites that adhere to design for all principles, but has sought to enhance understanding of information seeking behaviour of blind and visually impaired people when using digital resources.

  1. The Study of Analytical Model of Library Electronic Resources Usage-A Case of Medical Electronic Resources

    Directory of Open Access Journals (Sweden)

    Chung-Yen Yu

    2014-10-01

    Full Text Available With the advents of internet, the importance of electronic resources is growing. Due to the increasing expensiveness of electronic resources, university libraries normally received budgets from parent institutions annually. They necessarily applied effective and systematic methods for decision making in electronic resources purchase or re-subscription. However, there are some difficulties in practices: First of all, libraries are unable to receive user records; second, the COUNTER statistics does not include details about users and their affiliation. As a result, one cannot conduct advanced user analysis based on the usage of users, institutions, and departments. To overcome the difficulties, this study presents a feasible model to analyze electronic resource usage effectively and flexibly. We set up a proxy server to collect actual usage raw data. By analyzing items in internet browsing records, associated with original library automatic system, this study aims at exploring how to use effective ways to analyze big data of website log data. We also propose the process of how original data to be transformed, cleared, integrated, and demonstrated. This study adopted a medical university library and its subscription of medical electronic resources as a case. Our data analysis includes (1 year of subscription,(2 title of journal, (3 affiliation, (4 subjects, and (5 specific journal requirements, etc. The findings of the study are contributed to obtain further understanding in policy making and user behavior analysis. The integrated data provides multiple applications in informatics research, information behavior, bibliomining, presenting diverse views and extended issues for further discussion.

  2. Practical guide to electronic resources in the humanities

    CERN Document Server

    Dubnjakovic, Ana

    2010-01-01

    From full-text article databases to digitized collections of primary source materials, newly emerging electronic resources have radically impacted how research in the humanities is conducted and discovered. This book, covering high-quality, up-to-date electronic resources for the humanities, is an easy-to-use annotated guide for the librarian, student, and scholar alike. It covers online databases, indexes, archives, and many other critical tools in key humanities disciplines including philosophy, religion, languages and literature, and performing and visual arts. Succinct overviews of key eme

  3. Discipline, availability of electronic resources and the use of Finnish National Electronic Library - FinELib

    Directory of Open Access Journals (Sweden)

    Sanna Torma

    2004-01-01

    Full Text Available This study elaborated relations between digital library use by university faculty, users' discipline and the availability of key resources in the Finnish National Electronic Library (FinELib, Finnish national digital library, by using nationwide representative survey data. The results show that the perceived availability of key electronic resources by researchers in FinELib was a stronger predictor of the frequency and purpose of use of its services than users' discipline. Regardless of discipline a good perceived provision of central resources led to a more frequent use of FinELib. The satisfaction with the services did not vary with the discipline, but with the perceived availability of resources.

  4. Providing Access to Electronic Information Resources in Further Education

    Science.gov (United States)

    Banwell, Linda; Ray, Kathryn; Coulson, Graham; Urquhart, Christine; Lonsdale, Ray; Armstrong, Chris; Thomas, Rhian; Spink, Sin; Yeoman, Alison; Fenton, Roger; Rowley, Jennifer

    2004-01-01

    This article aims to provide a baseline for future studies on the provision and support for the use of digital or electronic information services (EIS) in further education. The analysis presented is based on a multi-level model of access, which encompasses access to and availability of information and communication technology (ICT) resources,…

  5. ANALYTICAL REVIEW OF ELECTRONIC RESOURCES FOR THE STUDY OF LATIN

    Directory of Open Access Journals (Sweden)

    Olena Yu. Balalaieva

    2014-04-01

    Full Text Available The article investigates the current state of development of e-learning content in the Latin language. It is noted that the introduction of ICT in the educational space has expanded the possibility of studying Latin, opened access to digital libraries resources, made it possible to use scientific and educational potential and teaching Latin best practices of world's leading universities. A review of foreign and Ukrainian information resources and electronic editions for the study of Latin is given. Much attention was paid to the didactic potential of local and online multimedia courses of Latin, electronic textbooks, workbooks of interactive tests and exercises, various dictionaries and software translators, databases and digital libraries. Based on analysis of the world market of educational services and products the main trends in the development of information resources and electronic books are examined. It was found that multimedia courses with interactive exercises or workbooks with interactive tests, online dictionaries and translators are the most widely represented and demanded. The noticeable lagging of Ukrainian education and computer linguistics in quantitative and qualitative measures in this industry is established. The obvious drawback of existing Ukrainian resources and electronic editions for the study of Latin is their noninteractive nature. The prospects of e-learning content in Latin in Ukraine are outlined.

  6. Electronic Commerce Resource Centers. An Industry--University Partnership.

    Science.gov (United States)

    Gulledge, Thomas R.; Sommer, Rainer; Tarimcilar, M. Murat

    1999-01-01

    Electronic Commerce Resource Centers focus on transferring emerging technologies to small businesses through university/industry partnerships. Successful implementation hinges on a strategic operating plan, creation of measurable value for customers, investment in customer-targeted training, and measurement of performance outputs. (SK)

  7. Student Satisfaction with Electronic Library Resources at Wayne State University

    Science.gov (United States)

    Holley, Robert P.; Powell, Ronald R.

    2004-01-01

    This paper reports the results of a survey of student satisfaction with electronic library resources other than the online catalog at Wayne State University. Undertaken in Fall Term 2000 as a class project for a marketing course, a student team designed, administered, and analyzed a survey of a random sample of students. Almost 40% of the…

  8. Electronic Commerce Resource Centers. An Industry--University Partnership.

    Science.gov (United States)

    Gulledge, Thomas R.; Sommer, Rainer; Tarimcilar, M. Murat

    1999-01-01

    Electronic Commerce Resource Centers focus on transferring emerging technologies to small businesses through university/industry partnerships. Successful implementation hinges on a strategic operating plan, creation of measurable value for customers, investment in customer-targeted training, and measurement of performance outputs. (SK)

  9. Technical Communicator: A New Model for the Electronic Resources Librarian?

    Science.gov (United States)

    Hulseberg, Anna

    2016-01-01

    This article explores whether technical communicator is a useful model for electronic resources (ER) librarians. The fields of ER librarianship and technical communication (TC) originated and continue to develop in relation to evolving technologies. A review of the literature reveals four common themes for ER librarianship and TC. While the…

  10. Providing Access to Electronic Information Resources in Further Education

    Science.gov (United States)

    Banwell, Linda; Ray, Kathryn; Coulson, Graham; Urquhart, Christine; Lonsdale, Ray; Armstrong, Chris; Thomas, Rhian; Spink, Sin; Yeoman, Alison; Fenton, Roger; Rowley, Jennifer

    2004-01-01

    This article aims to provide a baseline for future studies on the provision and support for the use of digital or electronic information services (EIS) in further education. The analysis presented is based on a multi-level model of access, which encompasses access to and availability of information and communication technology (ICT) resources,…

  11. Teeth grinding, oral motor performance and maximal bite force in cerebral palsy children.

    Science.gov (United States)

    Botti Rodrigues Santos, Maria Teresa; Duarte Ferreira, Maria Cristina; de Oliveira Guaré, Renata; Guimarães, Antonio Sergio; Lira Ortega, Adriana

    2015-01-01

    Identify whether the degree of oral motor performance is related to the presence of teeth grinding and maximal bite force values in children with spastic cerebral palsy. Ninety-five spastic cerebral palsy children with and without teeth grinding, according to caregivers' reports, were submitted to a comprehensive oral motor performance evaluation during the feeding process using the Oral Motor Assessment Scale. Maximal bite force was measured using an electronic gnathodynamometer. The teeth grinding group (n = 42) was younger, used anticonvulsant drugs, and was more frequently classified within the subfunctional oral motor performance category. Teeth grinding subfunctional spastic cerebral palsy children presented lower values of maximal bite force. The functional groups showing the presence or absence of teeth grinding presented higher values of maximal bite force compared with the subfunctional groups. In spastic cerebral palsy children, teeth grinding is associated with the worse oral motor performance. © 2015 Special Care Dentistry Association and Wiley Periodicals, Inc.

  12. Evaluating the appropriateness of electronic information resources for learning.

    Science.gov (United States)

    Saparova, Dinara; Nolan, Nathanial S

    2016-01-01

    Current US medical students have begun to rely on electronic information repositories-such as UpToDate, AccessMedicine, and Wikipedia-for their pre-clerkship medical education. However, it is unclear whether these resources are appropriate for this level of learning due to factors involving information quality, level of evidence, and the requisite knowledgebase. This study evaluated appropriateness of electronic information resources from a novel perspective: amount of mental effort learners invest in interactions with these resources and effects of the experienced mental effort on learning. Eighteen first-year medical students read about three unstudied diseases in the above-mentioned resources (a total of fifty-four observations). Their eye movement characteristics (i.e., fixation duration, fixation count, visit duration, and task-evoked pupillary response) were recorded and used as psychophysiological indicators of the experienced mental effort. Post reading, students' learning was assessed with multiple-choice tests. Eye metrics and test results constituted quantitative data analyzed according to the repeated Latin square design. Students' perceptions of interacting with the information resources were also collected. Participants' feedback during semi-structured interviews constituted qualitative data and was reviewed, transcribed, and open coded for emergent themes. Compared to AccessMedicine and Wikipedia, UpToDate was associated with significantly higher values of eye metrics, suggesting learners experienced higher mental effort. No statistically significant difference between the amount of mental effort and learning outcomes was found. More so, descriptive statistical analysis of the knowledge test scores suggested similar levels of learning regardless of the information resource used. Judging by the learning outcomes, all three information resources were found appropriate for learning. UpToDate, however, when used alone, may be less appropriate for first

  13. MODEL OF AN ELECTRONIC EDUCATIONAL RESOURCE OF NEW GENERATION

    Directory of Open Access Journals (Sweden)

    Anatoliy V. Loban

    2016-01-01

    Full Text Available The mathematical structure of the modular architecture of an electronic educational resource (EER of new generation, which allows to decompose the process of studying the subjects of the course at a hierarchically ordered set of data (knowledge and procedures for manipulating them, to determine the roles of participants of process of training of and technology the development and use of EOR in the study procrate.

  14. Evaluating increased resource use in fibromyalgia using electronic health records

    Directory of Open Access Journals (Sweden)

    Margolis JM

    2016-11-01

    Full Text Available Jay M Margolis,1 Elizabeth T Masters,2 Joseph C Cappelleri,3 David M Smith,1 Steven Faulkner4 1Truven Health Analytics, Life Sciences, Outcomes Research, Bethesda, MD, 2Pfizer Inc, Outcomes & Evidence, New York, NY, 3Pfizer Inc, Statistics, Groton, CT, 4Pfizer Inc, North American Medical Affairs, Medical Outcomes Specialists, St Louis, MO, USA Objective: The management of fibromyalgia (FM, a chronic musculoskeletal disease, remains challenging, and patients with FM are often characterized by high health care resource utilization. This study sought to explore potential drivers of all-cause health care resource utilization and other factors associated with high resource use, using a large electronic health records (EHR database to explore data from patients diagnosed with FM. Methods: This was a retrospective analysis of de-identified EHR data from the Humedica database. Adults (≥18 years with FM were identified based on ≥2 International Classification of Diseases, Ninth Revision codes for FM (729.1 ≥30 days apart between January 1, 2008 and December 31, 2012 and were required to have evidence of ≥12 months continuous care pre- and post-index; first FM diagnosis was the index event; 12-month pre- and post-index reporting periods. Multivariable analysis evaluated relationships between variables and resource utilization. Results: Patients were predominantly female (81.4%, Caucasian (87.7%, with a mean (standard deviation age of 54.4 (14.8 years. The highest health care resource utilization was observed for the categories of “medication orders” and “physician office visits,” with 12-month post-index means of 21.2 (21.5 drug orders/patient and 15.1 (18.1 office visits/patient; the latter accounted for 73.3% of all health care visits. Opioids were the most common prescription medication, 44.3% of all patients. The chance of high resource use was significantly increased (P<0.001 26% among African-Americans vs Caucasians and for patients

  15. Bruxism (Teeth Grinding or Clenching) (For Parents)

    Science.gov (United States)

    ... Old Feeding Your 1- to 2-Year-Old Bruxism (Teeth Grinding or Clenching) KidsHealth > For Parents > Bruxism ( ... called bruxism , which is common in kids. About Bruxism Bruxism is the medical term for the grinding ...

  16. Online Electronic Resources and Slovenian Bibliography: a Case Study

    Directory of Open Access Journals (Sweden)

    Daniela Škerget

    2014-09-01

    Full Text Available AbstractConsidering the fact that the number of publications available online only is growing, the question whether to include online electronic resources into the Slovenian bibliography, and if so, in which way, and what are the requirements for the inclusion, is raised. To answer these questions, the research on the growth of the Slovenian online scientific production in comparison with production in printed form was conducted in the case of original scientific articles. Results showed a rapid growth of the number of original scientific articles available online only, which indicates the necessity to form a separate Slovenian bibliography of online resources. The selection criteria for the Slovenian bibliography of online resources are also presented. This kind of bibliography would, along with the informational value, add to the historical value of intellectual production in a given time frame, enriched with a link to the resource preserved in another location (archive, repository, in case of unavailability of the resource on its original location.

  17. "Grinding" cavities in polyurethane foam

    Science.gov (United States)

    Brower, J. R.; Davey, R. E.; Dixon, W. F.; Robb, P. H.; Zebus, P. P.

    1980-01-01

    Grinding tool installed on conventional milling machine cuts precise cavities in foam blocks. Method is well suited for prototype or midsize production runs and can be adapted to computer control for mass production. Method saves time and materials compared to bonding or hot wire techniques.

  18. Journals, Data and Abstracts Make an Integrated Electronic Resource

    Science.gov (United States)

    Boyce, P.

    1996-12-01

    Astronomy now has an integrated, Web-based information resource for research papers, data and bibliographic information. The major scholarly research journals, a comprehensive abstract service and the astronomical data centers are now linked together to provide an information resource which is not available to most other scientific disciplines. As of January, 1997, the Astrophysical Journal joins the ApJ Letters on the Web. Astronomy and Astrophysics Supplements now has a page image version. Elsevier's electronic journal New Astronomy has recently made its appearance. Over forty percent of the new peer-reviewed, astronomical literature is now available electronically. The main Astronomy and Astrophysics journal, the Astronomical Journal and others will be available by 1998, at which point ninety percent of the literature will be available electronically, a figure not approached by any other scientific discipline. With so many different sources, one of the challenges has been to integrate the on-line, peer-reviewed literature into a resource which serves the astronomical community in a unified and coherent manner. Following the lead of the AAS, the major publishers have chosen to rely upon the NASA-supported Astrophysics Data System (ADS) and the astronomical data centers to provide the means by which the various separate journals can interoperate. The data centers and the ADS have developed unique identification codes for journal articles. By adopting the existing standard "bibcodes" and integrating them into their WWW links, each of the major astronomical journals are able to link to the abstracts of most of the referenced articles. Since the ADS also serves as an on-line repository for page images of the past twenty years of the major astronomical journals, the full text of many of the referenced articles are available, too. The articles in the ADS have recently been linked through their references, both forward and backward in time. With the "bibcode" providing

  19. Unsteady-State Grinding Technology (I) Theoretical Generalization and Research on Grinding Mechanism

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    In conventional grinding theory, it is obvious that there must be a very high hardness difference between grains of the grinding wheel and workpieces. The best grinding wheels are those giving the lowest "natural limiting surface roughness" while cutting at appreciable plunge velocities. With the development of new materials and new machining processes, conventional theories of grinding techniques are no longer suitable to explain many phenomena in the course of grinding procedures. In dealing with precisio...

  20. Ultrasonic precision optical grinding technology

    Science.gov (United States)

    Cahill, Michael J.; Bechtold, Michael J.; Fess, Edward; Wolfs, Frank L.; Bechtold, Rob

    2015-10-01

    As optical geometries become more precise and complex and a wider range of materials are used, the processes used for manufacturing become more critical. As the preparatory stage for polishing, this is especially true for grinding. Slow processing speeds, accelerated tool wear, and poor surface quality are often detriments in manufacturing glass and hard ceramics. The quality of the ground surface greatly influences the polishing process and the resulting finished product. Through extensive research and development, OptiPro Systems has introduced an ultrasonic assisted grinding technology, OptiSonic, which has numerous advantages over traditional grinding processes. OptiSonic utilizes a custom tool holder designed to produce oscillations in line with the rotating spindle. A newly developed software package called IntelliSonic is integral to this platform. IntelliSonic automatically characterizes the tool and continuously optimizes the output frequency for optimal cutting while in contact with the part. This helps maintain a highly consistent process under changing load conditions for a more accurate surface. Utilizing a wide variety of instruments, test have proven to show a reduction in tool wear and increase in surface quality while allowing processing speeds to be increased. OptiSonic has proven to be an enabling technology to overcome the difficulties seen in grinding of glass and hard optical ceramics. OptiSonic has demonstrated numerous advantages over the standard CNC grinding process. Advantages are evident in reduced tool wear, better surface quality, and reduced cycle times due to increased feed rates. These benefits can be seen over numerous applications within the precision optics industry.

  1. THERMAL STUDY ON THE GRINDING OF GRANITE WITH SUPERABRASIVE TOOLS

    Institute of Scientific and Technical Information of China (English)

    2003-01-01

    In the present paer, a thermal study was conducted for the grinding of granite with diamond tools. Three types of grinding-straight surface grinding, deep grinding(circular sawing), and vertical spindle grinding-were studied. Some surface grinding tests were also conducted using a CBN(cubic boron nitride) wheel. Temperature distributions on the workpiece surface were measured using a foil thermocouple and the energy partition to the workpiece was estimated using a temperature matching method. The temperature for CBN surface grinding was found to be much higher than for diamond grinding. Energy partitions to the granite were 30%~36% for CBN surface grinding, 25%~32% for diamond surface grinding, about 53% for vertical spindle grinding, and 5.5%~9% for diamond deep grinding. The low energy partition value in deep grinding also suggested that more of the heat generated by grinding in this case can be conducted to the grinding tool and promote tool wear.

  2. Analysis of Human Resources Management Strategy in China Electronic Commerce Enterprises

    Science.gov (United States)

    Shao, Fang

    The paper discussed electronic-commerce's influence on enterprise human resources management, proposed and proved the human resources management strategy which electronic commerce enterprise should adopt from recruitment strategy to training strategy, keeping talent strategy and other ways.

  3. Resources

    Science.gov (United States)

    ... resources Alzheimer's - resources Anorexia nervosa - resources Arthritis - resources Asthma and allergy - resources Autism - resources Blindness - resources BPH - resources Breastfeeding - resources Bulimia - resources Burns - resources Cancer - resources Cerebral ...

  4. Discipline, Availability of Electronic Resources and the Use of Finnish National Electronic Library-- FinELib

    Science.gov (United States)

    Törmä, Sanna; Vakkari, Pertti

    2004-01-01

    This study elaborated relations between digital library use by university faculty, users' discipline and the availability of key resources in the Finnish National Electronic Library (FinELib), Finnish national digital library, by using nationwide representative survey data. The results show that the perceived availability of key electronic…

  5. Surface grinding of intermetallic titanium aluminides

    CERN Document Server

    Gröning, Holger Andreas

    2014-01-01

    A deductive kinematic model of creep-feed and speed-stroke grinding processes is developed to identify possibilities to reduce the energy introduced into the workpiece. By computer tomography analysis and tactile measurements of the grinding wheel the pore volume and the static cutting edge number are determined and included in the model. Based on the kinematic model and the grinding wheel characteristics an analytical evaluation of the specific grinding energy for speed-stroke and creep-feed grinding is carried out. The deducted process design is evaluated in experimental investigations. The

  6. Force Characteristics in Continuous Path Controlled Crankpin Grinding

    Institute of Scientific and Technical Information of China (English)

    ZHANG Manchao; YAO Zhenqiang

    2015-01-01

    Recent research on the grinding force involved in cylindrical plunge grinding has focused mainly on steady-state conditions. Unlike in conventional external cylindrical plunge grinding, the conditions between the grinding wheel and the crankpin change periodically in path controlled grinding because of the eccentricity of the crankpin and the constant rotational speed of the crankshaft. The objective of this study is to investigate the effects of various grinding conditions on the characteristics of the grinding force during continuous path controlled grinding. Path controlled plunge grinding is conducted at a constant rotational speed using a cubic boron nitride (CBN) wheel. The grinding force is determined by measuring the torque. The experimental results show that the force and torque vary sinusoidally during dry grinding and load grinding. The variations in the results reveal that the resultant grinding force and torque decrease with higher grinding speeds and increase with higher peripheral speeds of the pin and higher grinding depths. In path controlled grinding, unlike in conventional external cylindrical plunge grinding, the axial grinding force cannot be disregarded. The speeds and speed ratios of the workpiece and wheel are also analyzed, and the analysis results show that up-grinding and down-grinding occur during the grinding process. This paper proposes a method for describing the force behavior under varied process conditions during continuous path controlled grinding, which provides a beneficial reference for describing the material removal mechanism and for optimizing continuous controlled crankpin grinding.

  7. End-of-life resource recovery from emerging electronic products

    DEFF Research Database (Denmark)

    Parajuly, Keshav; Habib, Komal; Cimpan, Ciprian

    2016-01-01

    of emerging electronic product, in order to understand the recovery fate of different materials and its linkage to product design. Ten different brands of RVC were dismantled and their material composition and design profiles were studied. Another 125 RVCs (349 kg) were used for an experimental trial......Integrating product design with appropriate end-of-life (EoL) processing is widely recognized to have huge potentials in improving resource recovery from electronic products. In this study, we investigate both the product characteristics and EoL processing of robotic vacuum cleaner (RVC), as a case...... at a conventional ‘shred-and-separate’ type preprocessing plant in Denmark. A detailed material flow analysis was performed throughout the recycling chain. The results show a mismatch between product design and EoL processing, and the lack of practical implementation of ‘Design for EoL’ thinking. In the best...

  8. Electronic Resources and Mission Creep: Reorganizing the Library for the Twenty-First Century

    Science.gov (United States)

    Stachokas, George

    2009-01-01

    The position of electronic resources librarian was created to serve as a specialist in the negotiation of license agreements for electronic resources, but mission creep has added more functions to the routine work of electronic resources such as cataloging, gathering information for collection development, and technical support. As electronic…

  9. Effects of Electronic Information Resources Skills Training for Lecturers on Pedagogical Practices and Research Productivity

    Science.gov (United States)

    Bhukuvhani, Crispen; Chiparausha, Blessing; Zuvalinyenga, Dorcas

    2012-01-01

    Lecturers use various electronic resources at different frequencies. The university library's information literacy skills workshops and seminars are the main sources of knowledge of accessing electronic resources. The use of electronic resources can be said to have positively affected lecturers' pedagogical practices and their work in general. The…

  10. Method for grinding precision components

    Science.gov (United States)

    Ramanath, Srinivasan; Kuo, Shih Yee; Williston, William H.; Buljan, Sergej-Tomislav

    2000-01-01

    A method for precision cylindrical grinding of hard brittle materials, such as ceramics or glass and composites comprising ceramics or glass, provides material removal rates as high as 19-380 cm.sup.3 /min/cm. The abrasive tools used in the method comprise a strong, light weight wheel core bonded to a continuous rim of abrasive segments containing superabrasive grain in a dense metal bond matrix.

  11. Analysis of Grinding Force and Elastic Deformation in Thread Grinding Process

    Directory of Open Access Journals (Sweden)

    Wei Wang

    2013-01-01

    Full Text Available Considering the grinding geometry of the thread grinding dynamic contact arc length, a dynamic numerical thread grinding model has been set up on the basis of study of a single grit grinding model. The properties of grinding force and dynamic contact arc-length have been studied by means of the developed numerical model. The results have shown that the angle of helix has little effect on the dynamic contact arc-length than the wheel speed on the dynamic contact arc-length. And the wheel speed also produced a large effect on grinding force.

  12. Electronic Document Management: A Human Resource Management Case Study

    Directory of Open Access Journals (Sweden)

    Thomas Groenewald

    2004-11-01

    Full Text Available This case study serve as exemplar regarding what can go wrong with the implementation of an electronic document management system. Knowledge agility and knowledge as capital, is outlined against the backdrop of the information society and knowledge economy. The importance of electronic document management and control is sketched thereafter. The literature review is concluded with the impact of human resource management on knowledge agility, which includes references to the learning organisation and complexity theory. The intervention methodology, comprising three phases, follows next. The results of the three phases are presented thereafter. Partial success has been achieved with improving the human efficacy of electronic document management, however the client opted to discontinue the system in use. Opsomming Die gevalle studie dien as voorbeeld van wat kan verkeerd loop met die implementering van ’n elektroniese dokumentbestuur sisteem. Teen die agtergrond van die inligtingsgemeenskap en kennishuishouding word kennissoepelheid en kennis as kapitaal bespreek. Die literatuurstudie word afgesluit met die inpak van menslikehulpbronbestuur op kennissoepelheid, wat ook die verwysings na die leerorganisasie en kompleksietydsteorie insluit. Die metodologie van die intervensie, wat uit drie fases bestaan, volg daarna. Die resultate van die drie fases word vervolgens aangebied. Slegs gedeelte welslae is behaal met die verbetering van die menslike doeltreffendheid ten opsigte van elektroniese dokumentbestuur. Die klient besluit egter om nie voort te gaan om die huidige sisteem te gebruik nie.

  13. Study on corrosive grinding of gears

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    Careful grinding or honing is usually required in machining of gears in order to improvethe machining quality of gear surface. Thus several grinding additives were used to formulate syn-thetic grinding lubricants similar to superior running-in lubricants. Experimental results show thatthe tooth surface of the produced oblique gear and steel worm becomes extremely smooth aftergrinding at a certain load for about a half to one hour. Especially, the gear surface finished withspecially formulated grinding lubricant reaches mirror-like smoothness. The quality of the geartooth can be improved by corrosive grinding, while the corrosive grinding time can be controlled byadjusting the quantity of the corrosive additives and the speed and load of the gears.

  14. [Radical formation by grinding of commercial tablets according to hospital and pharmacy prescription].

    Science.gov (United States)

    Kuzuya, Masayuki; Kondo, Shin-ichi; Ishikawa, Takaaki; Furuta, Youji; Aramaki, Hideki; Sasai, Yasushi; Yamauchi, Yukinori

    2005-04-01

    We examined mechanoradical formation in the grinding process of commercial tablets using electron spin resonance (ESR). Mechanoradicals were detected in all tested samples (23 types of commercial tablets) when the ball-milling of tablets was conducted under anaerobic conditions and some were fairly stable even in air. Thus the grinding may cause changes in the physicochemical properties of ingredients included in commercial tablets. Because high quality is demanded in pharmaceuticals, these results suggest more caution should be taken in the grinding of commercial tablets in hospitals and pharmacies.

  15. Experimental Setup for Diamond Grinding Using Electrochemical InProcess Controlled Dressing (ECD) of Grinding Wheel

    OpenAIRE

    M. A. Shavva; E. M. Zaharevich

    2014-01-01

    The most effective method for finish machining of hard-metals and alloys is to use the diamond grinding wheels for grinding. An application of diamond wheels significantly increases the employee output, reduces costs, and raises manufacturing efficiency with achieving the high performance properties of treated surfaces.During grinding a working surface of diamond wheel wears out. It adversely affects the cutting capability of the diamond grains, and depending on the grinding conditions can oc...

  16. Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

    Directory of Open Access Journals (Sweden)

    Zhang Dongkun

    2015-04-01

    Full Text Available Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication (MQL, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm3, respectively. The specific grinding energy significantly decreased to 32.7 J/mm3 in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%, respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%, and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS2, carbon nanotube (CNT, and ZrO2 nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS2 nanoparticle was only 32.7 J/mm3, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS2 nanoparticle, which indicated its remarkable lubrication effects. Furthermore, the role of MoS2 particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS2 volume concentrations of 1%, 2%, and 3% were used. Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS2 nanoparticle volume concentration increased. Satisfactory grinding surface lubrication effects were obtained with 2% MoS2 nanoparticle volume concentration.

  17. Changeing of fly ash leachability after grinding

    Science.gov (United States)

    Lakatos, J.; Szabo, R.; Racz, A.; Banhidi, O.; Mucsi, G.

    2016-04-01

    Effect of grinding on the reactivity of fly ash used for geopolymer production was tested. Extraction technique using different alkaline and acidic solutions were used for detect the change of the solubility of elements due to the physical and mechano-chemical transformation of minerals in function of grinding time. Both the extraction with alkaline and acidic solution have detected improvement in solubility in function of grinding time. The enhancement in alkaline solution was approx. 100% in case of Si and Al. The acidic medium able to dissolve the fly ash higher manner than the alkaline, therefore the effect of grinding was found less pronounced.

  18. Study on the Friction Coefficient in Grinding

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The friction between the abrasive grains and workpi ec e is a crutial factor determining the main grinding output. Few studies have bee n carried out investigating the values of the friction coefficient in grinding, due to the difficulty of direct measurement. In this paper, a mathematical model of the friction coefficient in grinding has been established with the aid of a new grinding parameter C ge, which has close relations to wheel wear rate Z s, metal removal rate Z w, specific energy u and gr...

  19. IMPACT GRINDING OF DAMP MATERIALS

    Directory of Open Access Journals (Sweden)

    Ladaev Nikolay Mikhaylovich

    2012-10-01

    Centrifugal grinders were used to analyze the grinding process. The experimental data have proven that the probability of destruction of damp samples is a lot higher than the one of dry samples, given the same initial dimensions of particles and the loading intensity. The rise in the probability of destruction is stipulated by the fact that that the grinder speed at which crushing is triggered is lower in case of damp samples than in case of dry ones. Expressions for speed that describes destruction initiation and the probability of destruction depending on the type of materials, the moisture content and the loading intensity have been derived.

  20. Grinding induced martensite on the surface of rails

    DEFF Research Database (Denmark)

    Rasmussen, C.J.; Zhang, Xiaodan; Danielsen, Hilmar Kjartansson

    2014-01-01

    determined. Two different rail types R260 and R350HT that both had been ground by a grinding train were investigated. The rail sections, studied using optical and scanning electron microscopy, showed that the surface of both types of rails is covered with WELs. The hardness of the WEL is increased compared...... to the base material and the microstructural investigations reveal that a martensitic structure is present at the surface....

  1. Manufacturing processes 2 grinding, honing, lapping

    CERN Document Server

    Klocke, Fritz

    2009-01-01

    Presents a view of the most common machining and non-machining manufacturing processes. This volume describes the characteristics of abrasive tools, their design and manufacturing, followed by the fundamentals of grinding fluids. It also discusses grinding of different materials (steel, cast iron, hard and brittle materials, nickel and titanium).

  2. Electronic Safety Resource Tools -- Supporting Hydrogen and Fuel Cell Commercialization

    Energy Technology Data Exchange (ETDEWEB)

    Barilo, Nick F.

    2014-09-29

    The Pacific Northwest National Laboratory (PNNL) Hydrogen Safety Program conducted a planning session in Los Angeles, CA on April 1, 2014 to consider what electronic safety tools would benefit the next phase of hydrogen and fuel cell commercialization. A diverse, 20-person team led by an experienced facilitator considered the question as it applied to the eight most relevant user groups. The results and subsequent evaluation activities revealed several possible resource tools that could greatly benefit users. The tool identified as having the greatest potential for impact is a hydrogen safety portal, which can be the central location for integrating and disseminating safety information (including most of the tools identified in this report). Such a tool can provide credible and reliable information from a trustworthy source. Other impactful tools identified include a codes and standards wizard to guide users through a series of questions relating to application and specific features of the requirements; a scenario-based virtual reality training for first responders; peer networking tools to bring users from focused groups together to discuss and collaborate on hydrogen safety issues; and a focused tool for training inspectors. Table ES.1 provides results of the planning session, including proposed new tools and changes to existing tools.

  3. Precision diamond grinding of ceramics and glass

    Energy Technology Data Exchange (ETDEWEB)

    Smith, S.; Paul, H.; Scattergood, R.O.

    1988-12-01

    A new research initiative will be undertaken to investigate the effect of machine parameters and material properties on precision diamond grinding of ceramics and glass. The critical grinding depth to initiate the plastic flow-to-brittle fracture regime will be directly measured using plunge-grind tests. This information will be correlated with machine parameters such as wheel bonding and diamond grain size. Multiaxis grinding tests will then be made to provide data more closely coupled with production technology. One important aspect of the material property studies involves measuring fracture toughness at the very short crack sizes commensurate with grinding damage. Short crack toughness value`s can be much less than the long-crack toughness values measured in conventional fracture tests.

  4. Controlling user access to electronic resources without password

    Science.gov (United States)

    Smith, Fred Hewitt

    2015-06-16

    Described herein are devices and techniques for remotely controlling user access to a restricted computer resource. The process includes pre-determining an association of the restricted computer resource and computer-resource-proximal environmental information. Indicia of user-proximal environmental information are received from a user requesting access to the restricted computer resource. Received indicia of user-proximal environmental information are compared to associated computer-resource-proximal environmental information. User access to the restricted computer resource is selectively granted responsive to a favorable comparison in which the user-proximal environmental information is sufficiently similar to the computer-resource proximal environmental information. In at least some embodiments, the process further includes comparing user-supplied biometric measure and comparing it with a predetermined association of at least one biometric measure of an authorized user. Access to the restricted computer resource is granted in response to a favorable comparison.

  5. Grinding efficiency of abutment tooth with both dentin and core composite resin on axial plane.

    Science.gov (United States)

    Miho, Otoaki; Sato, Toru; Matsukubo, Takashi

    2015-01-01

    The purpose of this study was to evaluate grinding efficiency in abutment teeth comprising both dentin and core composite resin in the axial plane. Grinding was performed over 5 runs at two loads (0.5 or 0.25 N) and two feed rates (1 or 2 mm/sec). The grinding surface was observed with a 3-D laser microscope. Tomographic images of the grinding surfaces captured perpendicular to the feed direction were also analyzed. Using a non-ground surface as a reference, areas comprising only dentin, both dentin and core composite resin, or only core composite resin were analyzed to determine the angle of the grinding surface. Composite resins were subjected to the Vickers hardness test and scanning electron microscopy. Data were statistically analyzed using a one-way analysis of variance and multiple comparison tests. Multiple regression analysis was performed for load, feed rate, and Vickers hardness of the build-up material depending on number of runs. When grinding was performed at a constant load and feed rate, a greater grinding angle was observed in areas comprising both dentin and composite resin or only composite resin than in areas consisting of dentin alone. A correlation was found between machinability and load or feed rate in areas comprising both dentin and composite resin or composite resin alone, with a particularly high correlation being observed between machinability and load. These results suggest that great caution should be exercised in a clinical setting when the boundary between the dentin and composite resin is to be ground, as the angle of the grinding surface changes when the rotating diamond point begins grinding the composite resin.

  6. The Internet School of Medicine: use of electronic resources by medical trainees and the reliability of those resources.

    Science.gov (United States)

    Egle, Jonathan P; Smeenge, David M; Kassem, Kamal M; Mittal, Vijay K

    2015-01-01

    Electronic sources of medical information are plentiful, and numerous studies have demonstrated the use of the Internet by patients and the variable reliability of these sources. Studies have investigated neither the use of web-based resources by residents, nor the reliability of the information available on these websites. A web-based survey was distributed to surgical residents in Michigan and third- and fourth-year medical students at an American allopathic and osteopathic medical school and a Caribbean allopathic school regarding their preferred sources of medical information in various situations. A set of 254 queries simulating those faced by medical trainees on rounds, on a written examination, or during patient care was developed. The top 5 electronic resources cited by the trainees were evaluated for their ability to answer these questions accurately, using standard textbooks as the point of reference. The respondents reported a wide variety of overall preferred resources. Most of the 73 responding medical trainees favored textbooks or board review books for prolonged studying, but electronic resources are frequently used for quick studying, clinical decision-making questions, and medication queries. The most commonly used electronic resources were UpToDate, Google, Medscape, Wikipedia, and Epocrates. UpToDate and Epocrates had the highest percentage of correct answers (47%) and Wikipedia had the lowest (26%). Epocrates also had the highest percentage of wrong answers (30%), whereas Google had the lowest percentage (18%). All resources had a significant number of questions that they were unable to answer. Though hardcopy books have not been completely replaced by electronic resources, more than half of medical students and nearly half of residents prefer web-based sources of information. For quick questions and studying, both groups prefer Internet sources. However, the most commonly used electronic resources fail to answer clinical queries more than half

  7. Crystalline silica dust and respirable particulate matter during indoor concrete grinding - wet grinding and ventilated grinding compared with uncontrolled conventional grinding.

    Science.gov (United States)

    Akbar-Khanzadeh, Farhang; Milz, Sheryl; Ames, April; Susi, Pamela P; Bisesi, Michael; Khuder, Sadik A; Akbar-Khanzadeh, Mahboubeh

    2007-10-01

    The effectiveness of wet grinding (wet dust reduction method) and ventilated grinding (local exhaust ventilation method, LEV) in reducing the levels of respirable crystalline silica dust (quartz) and respirable suspended particulate matter (RSP) were compared with that of uncontrolled (no dust reduction method) conventional grinding. A field laboratory was set up to simulate concrete surface grinding using hand-held angle grinders in an enclosed workplace. A total of 34 personal samples (16 pairs side-by-side and 2 singles) and 5 background air samples were collected during 18 concrete grinding sessions ranging from 15-93 min. General ventilation had no statistically significant effect on operator's exposure to dust. Overall, the arithmetic mean concentrations of respirable crystalline silica dust and RSP in personal air samples during: (i) five sessions of uncontrolled conventional grinding were respectively 61.7 and 611 mg/m(3) (ii) seven sessions of wet grinding were 0.896 and 11.9 mg/m(3) and (iii) six sessions of LEV grinding were 0.155 and 1.99 mg/m(3). Uncontrolled conventional grinding generated relatively high levels of respirable silica dust and proportionally high levels of RSP. Wet grinding was effective in reducing the geometric mean concentrations of respirable silica dust 98.2% and RSP 97.6%. LEV grinding was even more effective and reduced the geometric mean concentrations of respirable silica dust 99.7% and RSP 99.6%. Nevertheless, the average level of respirable silica dust (i) during wet grinding was 0.959 mg/m(3) (38 times the American Conference of Governmental Industrial Hygienists [ACGIH] threshold limit value [TLV] of 0.025 mg/m(3)) and (ii) during LEV grinding was 0.155 mg/m(3) (6 times the ACGIH TLV). Further studies are needed to examine the effectiveness of a greater variety of models, types, and sizes of grinders on different types of cement in different positions and also to test the simulated field lab experimentation in the field.

  8. Developing Humanities Collections in the Digital Age: Exploring Humanities Faculty Engagement with Electronic and Print Resources

    Science.gov (United States)

    Kachaluba, Sarah Buck; Brady, Jessica Evans; Critten, Jessica

    2014-01-01

    This article is based on quantitative and qualitative research examining humanities scholars' understandings of the advantages and disadvantages of print versus electronic information resources. It explores how humanities' faculty members at Florida State University (FSU) use print and electronic resources, as well as how they perceive these…

  9. Developing Humanities Collections in the Digital Age: Exploring Humanities Faculty Engagement with Electronic and Print Resources

    Science.gov (United States)

    Kachaluba, Sarah Buck; Brady, Jessica Evans; Critten, Jessica

    2014-01-01

    This article is based on quantitative and qualitative research examining humanities scholars' understandings of the advantages and disadvantages of print versus electronic information resources. It explores how humanities' faculty members at Florida State University (FSU) use print and electronic resources, as well as how they perceive these…

  10. Electronic resource management practical perspectives in a new technical services model

    CERN Document Server

    Elguindi, Anne

    2012-01-01

    A significant shift is taking place in libraries, with the purchase of e-resources accounting for the bulk of materials spending. Electronic Resource Management makes the case that technical services workflows need to make a corresponding shift toward e-centric models and highlights the increasing variety of e-formats that are forcing new developments in the field.Six chapters cover key topics, including: technical services models, both past and emerging; staffing and workflow in electronic resource management; implementation and transformation of electronic resource management systems; the ro

  11. Strategic Planning for Electronic Resources Management: A Case Study at Gustavus Adolphus College

    Science.gov (United States)

    Hulseberg, Anna; Monson, Sarah

    2009-01-01

    Electronic resources, the tools we use to manage them, and the needs and expectations of our users are constantly evolving; at the same time, the roles, responsibilities, and workflow of the library staff who manage e-resources are also in flux. Recognizing a need to be more intentional and proactive about how we manage e-resources, the…

  12. Strategic Planning for Electronic Resources Management: A Case Study at Gustavus Adolphus College

    Science.gov (United States)

    Hulseberg, Anna; Monson, Sarah

    2009-01-01

    Electronic resources, the tools we use to manage them, and the needs and expectations of our users are constantly evolving; at the same time, the roles, responsibilities, and workflow of the library staff who manage e-resources are also in flux. Recognizing a need to be more intentional and proactive about how we manage e-resources, the…

  13. The Relevancy of Graduate Curriculum to Human Resource Professionals' Electronic Communication.

    Science.gov (United States)

    Hoell, Robert C.; Henry, Gordon O.

    2003-01-01

    Electronic communications of human resource professionals and the content of 23 university human resource management courses were categorized using the Human Resource Certification Institute's body of knowledge. Differences between proportion of topics discussed and topics covered in curricula suggest some topics are over- or undertaught.…

  14. Progress in abrasive and grinding technology

    CERN Document Server

    Xu, Xipeng

    2009-01-01

    The grinding and abrasive processing of materials are machining techniques which use bonded or loose abrasives to remove material from workpieces. Due to the well-known advantages of grinding and abrasive processes, advances in abrasive and grinding technology are always of great import in enhancing both productivity and component quality. In order to highlight the recent progress made in this field, the editor invited 21 world-wide contributions with the aim of gathering together all of the achievements of leading researchers into a single publication. The authors of the 21 invited papers, of

  15. The Inlet Engine Valves Grinding Using Different Types of Cutting Fluids and Grinding Wheels

    Directory of Open Access Journals (Sweden)

    Eraldo Jannone da Silva

    2002-06-01

    Full Text Available In this paper an experimental research is presented in which different types of cutting fluids (a cutting oil and three different types of soluble oils and grinding wheels (alumina and vitrified CBN were tested in the inlet engine valves grinding. As evaluation parameters the workpiece residual stress and the grinding wheel wear were analyzed. The cutting fluid and the grinding wheel types adopted resulted in changes in all the parameters, due to the different lubricant abilities among the fluids and due to the differences in the mechanical and thermal properties among the abrasives tested. For grinding this steel, the CBN wheel is the best choice, mainly due to compressive residual stress results obtained for all cutting fluids tested. The cutting oil is the most adequate cutting fluid to be used, due to its higher lubricity and ability in keeping the wheel sharp for longer periods of time, reducing the overall grinding energy and the thermal damage.

  16. 2015 Utilization of Electronic Information Resources in Ramat ...

    African Journals Online (AJOL)

    intensely powerful and has permeated all segments and ... Web (WWW) and the internet to make information more accessible. On the other ... access points on the campus and computer literacy is till .... resources are often faster to consult than.

  17. High Efficiency ELID Grinding of Garnet Ferrite

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Hard and brittle materials such as ferrite, optical glass and ceramics have been widely used in many fields because of their good characteristics and still gain more attentions. However, it is difficult to machine and get good surface quality. Some parts made of these materials have large machining allowances and need to be produced with large batch, but the machining efficiency is very low with usual grinding method. So it is of great importance to research the high efficiency grinding technology of hard ...

  18. Remote Electronic Resources and the OPAC: Illustrated by the Unisa Library Experience.

    Science.gov (United States)

    Van der Merwe, Ina; Van Eeden, Welna; Hartzer, Sandra

    This paper describes the Unisa (University of South Africa) Library's experience with cataloging remote electronic resources, including electronic journals, electronic text files, online databases, digital images, Unisa campus Web sites, and mailing list discussions. The first section discusses the decision to add bibliographic references for…

  19. Multiparameter Optimization and Controlling for Cylindrical Grinding Process

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    This paper bursts the bondage of conventional no-burn thought, presents an optimum strategy permitting burn appear in grinding roughing stage, but the burning layer can be summed on the following finishing stage. On the base of the basic grinding models, the objective function and constrained functions for the multiparameter optimum grinding models had been built in this paper. By the computer simulation, the nonlinear optimum grinding control parameters had been obtained, and the truth grinding process had...

  20. Mirror Surface Grinding of Steel Bonded Carbides

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The steel bonded carbide, a composite material, is very difficult to be machined to a fine finish mirror surface. In this paper, an electrolytic in-process dressing (ELID) grinding with metallic bond super-hard abrasive wheel was developed for grinding steel bonded carbide GT35. Factors affecting ELID grinding performance were analyzed by an atomic force microscope (AFM). Based on the analysis of AFM topography of the fine ground mirror surface of the steel bonded carbide, a schematic diagram of the mechanism of micro-removal of the ground surface was described. The AFM topography also shows that the hard brittle carbide particles, on the surface of steel bonded carbide, were machined out by ductile cutting. Since the grinding cracks in the ground surface are due to temperature gradient, temperature distribution in the grinding area was analyzed by finite element method (FEM). Experimental results indicate that a good mirror surface with Ra<0.02pm can be obtained by the developed ELID grinding system.

  1. Controlling user access to electronic resources without password

    Energy Technology Data Exchange (ETDEWEB)

    Smith, Fred Hewitt

    2017-08-22

    Described herein are devices and techniques for remotely controlling user access to a restricted computer resource. The process includes obtaining an image from a communication device of a user. An individual and a landmark are identified within the image. Determinations are made that the individual is the user and that the landmark is a predetermined landmark. Access to a restricted computing resource is granted based on the determining that the individual is the user and that the landmark is the predetermined landmark. Other embodiments are disclosed.

  2. Research on the processing speed of cam grinding

    Science.gov (United States)

    Peng, Baoying; Han, Qiushi

    2011-05-01

    Cam Grinding is a special kind of non-circular machining. The processing speed of cam grinding has a major influence on cam machining precision. In this paper, decomposed the X-axis feed speed and C-axis velocity by the tangential speed and normal speed in accordance with the curvature circle at the point of cam profile grinding. Proposed the cam grinding processing speed model and linear velocity calculation formula, the processing experiment on the CNC camshaft grinding machine results show that the cam grinding speed model is correct. Constant angular speed grinding and constant linear speed grinding are analyzed respectively, which provides a theoretical basis for cam grinding processing speed optimization.

  3. A Review of Literature on analysis of JIG Grinding Process

    DEFF Research Database (Denmark)

    Sudheesh, P. K.; Puthumana, Govindan

    2016-01-01

    in jig grinding, because of their uniformity and purity. In this paper, abrief review of the analysis of jig grinding process considering various research trends is presented. The areas highlighted are: optimization, selection of abrasives, selection of processing conditions and practical considerations......Jig grinding is a process practically used by tool and die makers in the creation of jigs or mating holes and pegs on dies.The abrasives normally used in jig grinding are divided into Natural Abrasives and Artificial Abrasives. Artificial Abrasiveare preferred in manufacturing of grinding wheels....... The optimization of parameters in jig grinding process is important to maximize productivity and to improve quality. The abrasives of hard jig grinding wheels get blunt quickly so these are recommended to grind workpiece of low hardness and soft grinding wheels are recommended for hard material workpieces. The jig...

  4. ONLINE GRINDING WHEEL WEAR COMPENSATION BY IMAGE BASED MEASURING TECHNIQUES

    Institute of Scientific and Technical Information of China (English)

    WAN Daping; HU Dejin; WU Qi; ZHANG Yonghong

    2006-01-01

    Automatic compensation of grinding wheel wear in dry grinding is accomplished by an image based online measurement method. A kind of PC-based charge-coupled device image recognition system is schemed out, which detects the topography changes of the grinding wheel surface. Profile data, which corresponds to the wear and the topography, is measured by using a digital image processing method. The grinding wheel wear is evaluated by analyzing the position deviation of the grinding wheel edge. The online wear compensation is achieved according to the measure results. The precise detection and automatic compensation system is integrated into an open structure CNC curve grinding machine. A practical application is carried out to fulfil the precision curve grinding. The experimental results confirm the benefits of the proposed techniques, and the online detection accuracy is less than 5 μm. The grinding machine provides higher precision according to the in-process grinding wheel error compensation.

  5. An Evaluation of Electronic Product Design Education Using Hypermedia-Resourced Learning Environments

    Science.gov (United States)

    Page, Tom; Thorsteinsson, Gisli

    2006-01-01

    The work outlined here provides a comprehensive report and formative observations of the development and implementation of hypermedia resources for learning and teaching used in conjunction with a managed learning environment (MLE). These resources are used to enhance teaching and learning of an electronics module in product design at final year…

  6. A Study on Developing Evaluation Criteria for Electronic Resources in Evaluation Indicators of Libraries

    Science.gov (United States)

    Noh, Younghee

    2010-01-01

    This study aimed to improve the current state of electronic resource evaluation in libraries. While the use of Web DB, e-book, e-journal, and other e-resources such as CD-ROM, DVD, and micro materials is increasing in libraries, their use is not comprehensively factored into the general evaluation of libraries and may diminish the reliability of…

  7. Managing Selection for Electronic Resources: Kent State University Develops a New System to Automate Selection

    Science.gov (United States)

    Downey, Kay

    2012-01-01

    Kent State University has developed a centralized system that manages the communication and work related to the review and selection of commercially available electronic resources. It is an automated system that tracks the review process, provides selectors with price and trial information, and compiles reviewers' feedback about the resource. It…

  8. Where Do Electronic Books Fit in the College Research Arsenal of Resources?

    Science.gov (United States)

    Barbier, Patricia

    2007-01-01

    Student use of electronic books has become an accepted supplement to traditional resources. Student use and satisfaction was monitored through an online course discussion board. Increased use of electronic books indicate this service is an accepted supplement to the print book collection.

  9. Where Do Electronic Books Fit in the College Research Arsenal of Resources?

    Science.gov (United States)

    Barbier, Patricia

    2007-01-01

    Student use of electronic books has become an accepted supplement to traditional resources. Student use and satisfaction was monitored through an online course discussion board. Increased use of electronic books indicate this service is an accepted supplement to the print book collection.

  10. Surface Waviness in Grinding of Thin Mould Insert Using Chilled Air as Coolant

    Institute of Scientific and Technical Information of China (English)

    Yeo; S; H; K; Ramesh

    2002-01-01

    On going trend of miniaturization in electronic rel at ed parts, which is an average of two times in every 5~7 years introduce grindin g challenges. In grinding process, the surface waviness control of thin parts is an ardent task due to its warpage, induced by the high specific grinding energy (2~10 J/mm 3). Therefore, coolant is often used to avoid thermal damage, obtai n better surface integrity and to prolong wheel life. However coolant, the incomp ressibility media introduce high forces at the gri...

  11. Research on Visualization in Scientific Computation of Grinding Temperature Field

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The paper introduces the concepts, classification and method of visualization in scientific computation. Visual C++ developing tool is used to compute surface grinding forces and grinding temperature field models. The three-dimensional entity model of workpiece is made with OpenGL tool, and the different colors on the workpiece entity show different value of temperature, so the visualization of grinding temperature field is realized. The temperature value of every points in grinding temperature field, the c...

  12. Reducing the Edge Chipping for Capillary End Face Grinding and Polishing

    Directory of Open Access Journals (Sweden)

    Hošek J.

    2013-05-01

    Full Text Available This paper presents results of glass capillary end face grinding and polishing by approach that reduces the edge chipping. Brittle materials have natural tendency for edge chipping what leads to beveling the sharp edges. Not beveled sharp edges on glass capillary are important for special applications like surface tension measurement of small liquid samples. We use common grinding and polishing process for capillary end face machining modified with gradual decreasing of grinding load based on the relation of the critical chipping load. Achieved surface roughness is measured using atomic force microscopy (AFM. Capillary inner edge quality is checked both with optical microscopes and electron microscope too. We achieved a non-chipped capillary inner edge with radius down to 100 nm.

  13. MULER: Building an Electronic Resource Management (ERM Solution at York University

    Directory of Open Access Journals (Sweden)

    Aaron August Lupton

    2012-01-01

    Full Text Available Many university libraries now utilize an Electronic Resource Management (ERM system to assist with operations related to electronic resources. An ERM is a relational database containing information such as suppliers, costs, holdings, and renewal dates for electronic resources, both at the database and title levels. While commercial ERM products are widely available, some institutions are custom building their own ERM in- house. This article describes how York University in Toronto, Canada, did just that by building a system called Managing University Library Electronic Resources (MULER. The article details the background and history of how electronic resources were managed pre-MULER; why a new ERM was needed; the planning process; the current and innovative functions of MULER, including integration of MULER data into York University Libraries search and discovery layer, Vufind; subject tagging in MULER; new functions to be added; and lessons learned from the project. Positive and negative implications of choosing an in-house project over paying for a commercial product are also discussed.

  14. FY 1998 annual report on the development of laser-aided, noncontacting, realtime, in-process dressing method using a grinding stone with ultrafine abrasive grains, and study on techniques for applying the method to grinding stone of superthin blades; 1998 nendo laser wo mochiita choteiryu toishi no hisesshoku real time inprocess dressing ho no kaihatsu oyobi gokuusuha toishi eno tekiyo gijutsu ni kansuru kenkyu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A new noncontacting dressing method using a laser as a tool has been studied and developed, in order to develop environment-compatible, energy-saving type machining machines. In this study, a cup-shaped grinding stone is developed for grinding performance testing by micron-order diamond abrasive powder, used for producing a grinding stone of superthin blades, is mixed with a cast iron binder, molded and sintered. In the grinding performance test, zirconia as a work is ground at a constant pressure to the grinding stone working surface before and after the laser-aided dressing, to analyze grinding/removal efficiency and grinding resistance. The grinding stone working surface conditions are observed by a scanning electron microscope after the laser-aided dressing, to correlate the surface conditions with the grinding data. It is found that the laser-aided dressing method needs no lubricant, is clean, cutting grinding time when incorporated in the machining process, suitable for grinding stone of low stiffness and ultrathin blades by use of ultrafine abrasive grains, suffering no exfoliation of the diamond grains, and hence economical. (NEDO)

  15. Effection of grinding system rigidity ultra-precision grinding of aspheric mould and error compensation

    Science.gov (United States)

    Yin, S. H.; Gong, S.

    2016-10-01

    In ultra-precision oblique axis grinding process for machining micro aspherical mould, form error of aspherical surface is caused by the inconsistence elastic deformation of grinding system, which derived from differences velocity from inside to out. In this case, whole PV value can meet requirements, however, pits are produced in central after error compensation, which is unworkable. In this paper, mechanism of machining error caused by grinding system rigidity is analyzed, and experiments are carried out. Form error compensation grinding are carried out in the central local area, based on traditional error compensation method, which can effectively eliminate the pits of surface center. In this method, cemented carbide YG8 which diameter is about 6mm is ground. The results showed that the form accuracy under PV 200 nm and under PV 50 nm within the scope of 1 mm, and the surface roughness under Ra2nm.

  16. Grinding of WC–Co hardmetals

    NARCIS (Netherlands)

    Hegeman, J.B.J.W.; Hosson, J.Th.M. De; With, G. de

    2001-01-01

    This paper concentrates on the morphology of the ground surface of cobalt tungsten carbide (WC) composite materials that belong to the category of so-called hardmetals. A deformed and detached surface layer was found on top of the specimens after surface grinding with a diamond wheel. In order to

  17. Pre-etching vs. grinding in promotion of adhesion to intact enamel using self-etch adhesives.

    Science.gov (United States)

    Nazari, Amir; Shimada, Yasushi; Sadr, Alireza; Tagami, Junji

    2012-01-01

    This study was aimed to determine the effectiveness of grinding and pre-etching in promotion of adhesion to human intact enamel using the self-etch adhesive (SEA) Adper Easy Bond (3M ESPE). Etch-and-rinse adhesive Adper Single Bond (3M ESPE) served as control. Composite cylinders (AP-X Kuraray) were built and after 24 h micro-shear bond strengths (MSBS) were measured. Bonding interfaces were evaluated under scanning electron microscope (SEM). For evaluation of average roughness (Ra) and morphological analysis, treated enamel surfaces were observed under SEM and confocal laser scanning microscope (CLSM) with 3D surface profiling. Highest bond strengths were obtained by pre-etching and grinding showed a less significant role. Phosphoric acid (PA) etching compare to grinding created significantly rougher surface (Ra: 0.72 and 0.43 µm respectively). Therefore, this study recommends pre-etching the intact enamel prior to application of the adhesive instead of grinding.

  18. The National Site Licensing of Electronic Resources: An Institutional Perspective

    Directory of Open Access Journals (Sweden)

    Xiaohua Zhu

    2011-06-01

    Full Text Available While academic libraries in most countries are struggling to negotiate with publishers and vendors individually or collaboratively via consortia, a few countries have experimented with a different model, national site licensing (NSL. Because NSL often involves government and large-scale collaboration, it has the potential to solve many problems in the complex licensing world. However, not many nations have adopted it. This study uses historical research approach and the comparative case study research method to explore the seemingly low level of adoption. The cases include the Canadian National Site Licensing Project (CNSLP, the United Kingdom’s National Electronic Site Licensing Initiative (NESLI, and the United States, which has not adopted NSL. The theoretical framework guiding the research design and data collection is W. Richard Scott’s institutional theory, which utilizes three supporting pillars—regulative, normative, and cultural-cognitive—to analyze institutional processes. In this study, the regulative pillar and the normative pillar of NSL adoption— an institutional construction and change—are examined. Data were collected from monographs, research articles, government documents, and relevant websites. Based on the analysis of these cases, a preliminary model is proposed for the adoption of NSL. The factors that support a country’s adoption of NSL include the need for new institutions, a centralized educational policy-making system and funding system, supportive political trends, and the tradition of cooperation. The factors that may prevent a country from adopting NSL include decentralized educational policy and funding, diversity and the large number of institutions, the concern for the “Big Deal,” and the concern for monopoly.

  19. Method of accurate grinding for single enveloping TI worm

    Institute of Scientific and Technical Information of China (English)

    SUN; Yuehai; ZHENG; Huijiang; BI; Qingzhen; WANG; Shuren

    2005-01-01

    TI worm drive consists of involute helical gear and its enveloping Hourglass worm. Accurate grinding for TI worm is the key manufacture technology for TI worm gearing being popularized and applied. According to the theory of gear mesh, the equations of tooth surface of worm drive are gained, and the equation of the axial section profile of grinding wheel that can accurately grind TI worm is extracted. Simultaneously,the relation of position and motion between TI worm and grinding wheel are expounded.The method for precisely grinding single enveloping TI worm is obtained.

  20. Analytical Study of Usage of Electronic Information Resources at Pharmacopoeial Libraries in India

    Directory of Open Access Journals (Sweden)

    Sunil Tyagi

    2014-02-01

    Full Text Available The objective of this study is to know the rate and purpose of the use of e-resource by the scientists at pharmacopoeial libraries in India. Among other things, this study examined the preferences of the scientists toward printed books and journals, electronic information resources, and pattern of using e-resources. Non-probability sampling specially accidental and purposive technique was applied in the collection of primary data through administration of user questionnaire. The sample respondents chosen for the study consists of principle scientific officer, senior scientific officer, scientific officer, and scientific assistant of different division of the laboratories, namely, research and development, pharmaceutical chemistry, pharmacovigilance, pharmacology, pharmacogonosy, and microbiology. The findings of the study reveal the personal experiences and perceptions they have had on practice and research activity using e-resource. The major findings indicate that of the total anticipated participants, 78% indicated that they perceived the ability to use computer for electronic information resources. The data analysis shows that all the scientists belonging to the pharmacopoeial libraries used electronic information resources to address issues relating to drug indexes and compendia, monographs, drugs obtained through online databases, e-journals, and the Internet sources—especially polices by regulatory agencies, contacts, drug promotional literature, and standards.

  1. Connecting knowledge resources to the veterinary electronic health record: opportunities for learning at point of care.

    Science.gov (United States)

    Alpi, Kristine M; Burnett, Heidi A; Bryant, Sheila J; Anderson, Katherine M

    2011-01-01

    Electronic health records (EHRs) provide clinical learning opportunities through quick and contextual linkage of patient signalment, symptom, and diagnosis data with knowledge resources covering tests, drugs, conditions, procedures, and client instructions. This paper introduces the EHR standards for linkage and the partners-practitioners, content publishers, and software developers-necessary to leverage this possibility in veterinary medicine. The efforts of the American Animal Hospital Association (AAHA) Electronic Health Records Task Force to partner with veterinary practice management systems to improve the use of controlled vocabulary is a first step in the development of standards for sharing knowledge at the point of care. The Veterinary Medical Libraries Section (VMLS) of the Medical Library Association's Task Force on Connecting the Veterinary Health Record to Information Resources compiled a list of resources of potential use at point of care. Resource details were drawn from product Web sites and organized by a metric used to evaluate medical point-of-care resources. Additional information was gathered from questions sent by e-mail and follow-up interviews with two practitioners, a hospital network, two software developers, and three publishers. Veterinarians with electronic records use a variety of information resources that are not linked to their software. Systems lack the infrastructure to use the Infobutton standard that has been gaining popularity in human EHRs. While some veterinary knowledge resources are digital, publisher sites and responses do not indicate a Web-based linkage of veterinary resources with EHRs. In order to facilitate lifelong learning and evidence-based practice, veterinarians and educators of future practitioners must demonstrate to veterinary practice software developers and publishers a clinically-based need to connect knowledge resources to veterinary EHRs.

  2. Improving access to information – defining core electronic resources for research and wellbeing

    Directory of Open Access Journals (Sweden)

    Kristiina Hormia-Poutanen

    2007-11-01

    Full Text Available Research and innovation are listed as the key success factors for the future development of Finnish prosperity and the Finnish economy. The Finnish libraries have developed a scenario to support this vision. University, polytechnic and research institute libraries as well as public libraries have defined the core electronic resources necessary to improve access to information in Finland. The primary aim of this work has been to provide information and justification for central funding for electronic resources to support the national goals. The secondary aim is to help with the reallocation of existing central funds to better support access to information.

  3. Research on CNC Turning System of Aspheric Machining Grinding Wheel

    Institute of Scientific and Technical Information of China (English)

    ZOU Qin; GUO Yin-biao

    2005-01-01

    The technology of machining aspheric surface with high precision is the premise for the application of aspheric surface. The grinding machining with error compensation is a commonly used method to machine aspheric surface, which will directly influence the quality of aspheric workpiece surface. Multifunctional CNC grinding wheel truing system is a four-axis CNC truing system which can be applied to grinding wheel truing. In this system,DSP-based multi-axes motion control card is adopted as the controller, and visual C++ is used as development tool.When the design of hardware and software is completed, the system can implement truing of various grinding wheel with high precision aspheric machining such as plane grinding wheel, arc grinding one, and sphere grinding one.

  4. Dry-grinded ultrafine cements hydration. physicochemical and microstructural characterization

    Directory of Open Access Journals (Sweden)

    Foteini Kontoleontos

    2013-04-01

    Full Text Available The aim of the present research work was the evaluation of the physicochemical and microstructural properties of two ultrafine cements, produced by dry grinding of a commercial CEM I 42.5N cement. The effect of grinding on particle size distribution was determined by laser scattering analyzer. All cements were tested for initial and final setting times, consistency of standard paste, soundness, flow of normal mortar and compressive strengths after 1, 2, 7 and 28 days. The effect of the fineness on the heat of hydration was also investigated. The hydration products were determined by X-ray diffraction analysis and by Fourier transform infrared spectroscopy, at 1, 2, 7 and 28 days. The microstructure of the hardened cement pastes and their morphological characteristics were examined by scanning electron microscopy. Porosity and pore size distribution were evaluated by mercury intrusion porosimetry. The effects of greater fineness on compressive strengths were evident principally at early ages. After the first 24 hours of hydration, the compressive strength of the finest cements was about 3 times higher (over 48 MPa than the corresponding of CEM I 42.5N (15.1 MPa.

  5. STUDY ON A NEW TYPE OF THROWAWAY SOFT GRINDING WHEELS

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    In accordance with the difficult problems of belt cross vibrations and effects of belt tension on machine spindle precision in abrasive belt grinding, a new soft grinding wheel is put forward, which is provided with the advantages of belt grinding and can be installed directly on the grinding machine spindle substituting for common grinding wheels. The new soft grinding wheel does not need any ancillary facilities and dressing devices in grinding. With analyzing error of wheel and grinding experiment, the highefficiency grinding characteristics grinding hardbrittle materials has been obtained.

  6. Elektronik Bilgi Kaynaklarının Seçimi / Selection of Electronic Information Resources

    Directory of Open Access Journals (Sweden)

    Pınar Al

    2003-04-01

    Full Text Available For many years, library users have used only from the printed media in order to get the information that they have needed. Today with the widespread use of the Web and the addition of electronic information resources to library collections, the use of information in the electronic environment as well as in printed media is started to be used. In time, such types of information resources as, electronic journals, electronic books, electronic encyclopedias, electronic dictionaries and electronic theses have been added to library collections. In this study, selection criteria that can be used for electronic information resources are discussed and suggestions are provided for libraries that try to select electronic information resources for their collections.

  7. Using Electronic Information Resources Centers by Faculty Members at University Education: Competencies, Needs and Challenges

    Science.gov (United States)

    Abouelenein, Yousri

    2017-01-01

    This study aimed at investigating the factual situation of electronic information resources centers to faculty members at university education. Competencies that faculty members should possess regarding this issue were determined. Also their needs for (scientific research skills and teaching) were assessed. In addition, problems that hinder their…

  8. Localising versus standardising electronic human resource management: complexities and tensions between HRM and IT departments

    NARCIS (Netherlands)

    Tate, Mary; Furtmueller, E.; Wilderom, C.P.M.

    2013-01-01

    In this paper, we provide an analysis of the complexities involved during global e-HRM (Electronic Human Resource Management) implementation. We present findings from a case study on the challenge of global integration versus local responsiveness of e-HRM systems. We take a local site lens, analysin

  9. Use of Electronic Information Resources among Research Scholars in the Islamia University of Bahawalpur, Pakistan

    Science.gov (United States)

    Amjad, Anam; Ahmed, Shamshad; Bin Naeem, Salman

    2013-01-01

    This study examined the use of electronic resources among academic scholars of The Islamia University of Bahawalpur (IUB), Punjab, Pakistan. A quantitative survey was found most convenient and useful for this study. The total population of the study was 169 research students in IUB. The response rate was 79% and 133 utilizable responses were coded…

  10. The Acquisition and Management of Electronic Resources: Can Use Justify Cost?

    Science.gov (United States)

    Koehn, Shona L.; Hawamdeh, Suliman

    2010-01-01

    As library collections increasingly become digital, libraries are faced with many challenges regarding the acquisition and management of electronic resources. Some of these challenges include copyright and fair use, the first-sale doctrine, licensing versus ownership, digital preservation, long-term archiving, and, most important, the issue of…

  11. 电子资源的编目策略%Cataloging Strategies of Electronic Resources

    Institute of Scientific and Technical Information of China (English)

    王亚林

    2012-01-01

    Compared with traditional paper resources, electronic resources have following characteristics which determine different cataloging strategies from paper resources. These characteristics are huge quantity, updating rapidly, coexistence of a variety of manifestations. The source data of electronic resources is usually provided by the database agent. The cataloging of electronic resources is based on the Chapter IX of Anglo-American Cataloging Rules, Library of Congress Rule Interpretations and rules of Cooperative Online Serials. There are two major cataloging methods for electronic resources abroad, they are single record approach and separate record approach. Peking University Library chooses the latter method and batches cataloging automatically using the source data.%电子资源吲传统纸质资源相比,具有数量大、更新快、多种载体表现并行等特点,且大部分出版机构能够提供数据源数据。这些特点决定了.电子资源应采取与纸质文献不同的编目策略。电子资源编日的主要依据是《英美编日条例》的第9章、美国《国会图书馆条例解释》及全美期刊合作编目计划的规定。对于电子资源的编目,国外有单一记录编目法和分散记录编目法。北京大学图书馆采用后者,同时利用数据源数据批舒自动编目。

  12. Power resource management and low-power remote wireless RF electronics

    Science.gov (United States)

    Jannson, Tomasz; Forrester, Thomas; Degrood, Kevin; Lee, Kang; Gans, Eric; Walter, Kevin

    2009-05-01

    Battery power resource management becomes a critical issue in the case of self-powered remote wireless RF electronics, where the basic parameter is time of system operation before battery recharging or battery replacement. In such cases, very often related to physical protection against antitampering (AT), proper theoretical modeling of a battery driven power supply in the context of a given digital electronic system is of utmost importance. Such modeling should include various types of batteries (primary and secondary), various self-discharge processes in different temperatures, and even energy harvesting, the latter to supply power for long-term content, low-power electronic subsystems. In this paper we analyze simple modeling of resource power management, including variations of all of these parameters and energy harvesting.

  13. System Analysis of Flat Grinding Process with Wheel Face

    Directory of Open Access Journals (Sweden)

    T. N. Ivanova

    2014-01-01

    Full Text Available The paper presents a conducted system analysis of the flat grinding wheel face, considers the state parameters, input and output variables of subsystems, namely: machine tool, workpiece, grinding wheel, cutting fluids, and the contact area. It reveals the factors influencing the temperature and power conditions for the grinding process.Aim: conducting the system analysis of the flat grinding process with wheel face expects to enable a development of the system of grinding process parameters as a technical system, which will make it possible to evaluate each parameter individually and implement optimization of the entire system.One of the most important criteria in defining the optimal process conditions is the grinding temperature, which, to avoid defects appearance of on the surface of component, should not exceed the critical temperature values to be experimentally determined. The temperature criterion can be useful for choosing the conditions for the maximum defect-free performance of the mechanical face grinding. To define the maximum performance of defect-free grinding can also use other criteria such as a critical power density, indirectly reflecting the allowable thermal stress grinding process; the structure of the ground surface, which reflects the presence or absence of a defect layer, which is determined after the large number of experiments; flow range of the diamond layer.Optimal conditions should not exceed those of defect-free grinding. It is found that a maximum performance depends on the characteristics of circles and grade of processed material, as well as on the contact area and grinding conditions. Optimal performance depends on the diamond value (cost and specific consumption of diamonds in a circle.Above criteria require formalization as a function of the variable parameters of the grinding process. There is an option for the compromise of inter-criteria optimality, thereby providing a set of acceptable solutions, from

  14. Identifying and evaluating electronic learning resources for use in adult-gerontology nurse practitioner education.

    Science.gov (United States)

    Thompson, Hilaire J; Belza, Basia; Baker, Margaret; Christianson, Phyllis; Doorenbos, Ardith; Nguyen, Huong

    2014-01-01

    Enhancing existing curricula to meet newly published adult-gerontology advanced practice registered nurse (APRN) competencies in an efficient manner presents a challenge to nurse educators. Incorporating shared, published electronic learning resources (ELRs) in existing or new courses may be appropriate in order to assist students in achieving competencies. The purposes of this project were to (a) identify relevant available ELR for use in enhancing geriatric APRN education and (b) to evaluate the educational utility of identified ELRs based on established criteria. A multilevel search strategy was used. Two independent team members reviewed identified ELR against established criteria to ensure utility. Only resources meeting all criteria were retained. Resources were found for each of the competency areas and included formats such as podcasts, Web casts, case studies, and teaching videos. In many cases, resources were identified using supplemental strategies and not through traditional search or search of existing geriatric repositories. Resources identified have been useful to advanced practice educators in improving lecture and seminar content in a particular topic area and providing students and preceptors with additional self-learning resources. Addressing sustainability within geriatric APRN education is critical for sharing of best practices among educators and for sustainability of teaching and related resources. © 2014.

  15. Pyrolysis of a waste from the grinding of scrap tyres.

    Science.gov (United States)

    Fernández, A M; Barriocanal, C; Alvarez, R

    2012-02-15

    The fibres that are used to reinforce tyres can be recovered as a waste in the process of grinding of scrap tyres. In this paper beneficiation through pyrolysis is studied since the fibres are made up of polymers with a small amount of rubber because the latter is difficult to separate. The experiments were performed at three temperatures (400, 550 and 900°C) in a horizontal oven. The three products - gas, oil and char - obtained from the pyrolysis were investigated. The composition of the gas was analyzed by means of gas chromatography. The oil was studied by gas chromatography and infrared spectroscopy. The char porous structure was determined by N(2) adsorption. In addition, the topography of the chars was studied by means of scanning electron microscopy (SEM). The products resulting from the pyrolysis of the fibres were compared with those obtained from scrap rubber.

  16. Experimental Setup for Diamond Grinding Using Electrochemical InProcess Controlled Dressing (ECD of Grinding Wheel

    Directory of Open Access Journals (Sweden)

    M. A. Shavva

    2014-01-01

    Full Text Available The most effective method for finish machining of hard-metals and alloys is to use the diamond grinding wheels for grinding. An application of diamond wheels significantly increases the employee output, reduces costs, and raises manufacturing efficiency with achieving the high performance properties of treated surfaces.During grinding a working surface of diamond wheel wears out. It adversely affects the cutting capability of the diamond grains, and depending on the grinding conditions can occur through different mechanisms. Wear of diamond wheel causes distortion of its shape and reduces cutting properties. However, dressing of diamond wheels is a complicated and time-consuming operation in terms of manufacturing technique.Methods to make dressing of diamond grinding wheel have different types of classification. Classification of dressing methods by the type of energy used is as follows: mechanical, chemical, electrophysical, electromechanical, and electrochemical. All these methods have their advantages and disadvantages.Electrochemical method of dressing is the most productive and efficient. Electrochemical method comprises anode-mechanical dressing and electrochemical (electrolytic one. The paper presents the electrochemical in-process dressing (ECD and the electrolytic in-process dressing (ELID.The source of energy, grinding a wheel with metal bond, and an electrode are necessary for providing ELID. The ELID consists of several stages. The first stage is preliminary electrolytic dressing of diamond wheel. The electrolyte is placed into the gap between the wheel and electrode. The bond of the wheel is oxidized. An insulating layer is formed. It reduces an electrical conductivity of the wheel and controls consumption of diamond grains, as well as polishes the surface of the work piece. Further, the insulating layer is destroyed. The cycle of dressing begins anew.The ECD proceeds in the same way as ELID. However during the ECD-process there

  17. Library Electronic Resource Sharing Among Liberal Arts Colleges: ACS Palladian Alliance Project

    Directory of Open Access Journals (Sweden)

    Wenxian Zhang

    1997-03-01

    Full Text Available 無Effective electronic resource sharing is critical to library information services of the 1990s. Explosion of data and increased cost of information force libraries to work together, and technological advancements present the library service profession a platform for resource sharing. The Palladian Alliance Project of the Associated Colleges of the South is designed to provides ACS member institutions an effective means to enhance information access for their faculty and students, and achieve significant cost containment in the years to come.

  18. Availability, Level of Use and Constraints to Use of Electronic Resources by Law Lecturers in Public Universities in Nigeria

    Science.gov (United States)

    Amusa, Oyintola Isiaka; Atinmo, Morayo

    2016-01-01

    (Purpose) This study surveyed the level of availability, use and constraints to use of electronic resources among law lecturers in Nigeria. (Methodology) Five hundred and fifty-two law lecturers were surveyed and four hundred and forty-two responded. (Results) Data analysis revealed that the level of availability of electronic resources for the…

  19. Electrochemical properties and Li deposition morphologies of surface modified graphite after grinding

    Science.gov (United States)

    Honbo, H.; Takei, K.; Ishii, Y.; Nishida, T.

    Electrochemical properties and Li deposition morphologies of several kinds of carbon with different surfaces were studied. The surface conditions and Li deposition morphologies were analyzed using Raman spectroscopy and scanning electron microscopy. It appeared that the disordered carbon surface suppressed the Li dendrite deposition. Grinding methods with different clearances were adopted to modify the graphite into a desirable surface. The R-value increased from 0.10 to 0.63 after grinding to 40 μm, though a significant change in d 0 0 2 did not occur. These results suggest that disordered carbon was created on the surface without a significant change in bulk crystallinity. Thus, the reversible capacity, which is about 350 mAh g -1, was the same before and after grinding. However, the Li deposition morphologies significantly changed before and after grinding. The pristine graphite had a dendritic morphology, but the ground graphite had a granular morphology. It is believed that the defects on the disordered carbon act as electrodeposition nuclei and prevent the formation of Li dendrites.

  20. Kinetic study of ferronickel slag grinding at variation of ball filling and ratio of feed to grinding balls

    Science.gov (United States)

    Sanwani, Edy; Ikhwanto, Muhammad

    2017-01-01

    The objective of this paper is to investigate the effect of ball filling and ratio of feed to grinding balls on the kinetic of grinding of ferronickel slag in a laboratory scale ball mill. The experiments were started by crushing the ferronickel slag samples using a roll crusher to produce -3 mesh (-6.7 mm) product. This product, after sampling and sample dividing processes, was then used as feed for grinding process. The grinding was performed with variations of ball filling and ratio of feed to grinding balls for 150 minutes. At every certain time interval, particle size analysis was carried out on the grinding product. The results of the experiments were also used to develop linear regression model of the effect of grinding variables on the P80 of the product. Based on this study, it was shown that P80 values of the grinding products declined sharply until 70 minutes of grinding time due to the dominant mechanism of impact breakage and then decreased slowly after 70 minutes until 150 minutes of grinding time due to dominant mechanism of attrition breakage. Kinetics study of the grinding process on variations of grinding ball filling showed that the optimum rate of formation of fine particles for 20%, 30%, 40% and 50% mill volume was achieved at a particle size of 400 µm in which the best initial rate of formation occurred at 50% volume of mill. At the variations of ratio of feed to grinding balls it was shown that the optimum rate of grinding for the ratio of 1:10, 1: 8 and 1: 6 was achieved at a particle size of 400 µm and for the ratio of 1: 4 was at 841 µm in which the best initial rate of formation occurred at a 1:10 ratio. In this study, it was also produced two regression models that can predict the P80 value of the grinding product as a function of the variables of grinding time, ball filling and the ratio of the feed to grinding balls.

  1. Separate critical condition for ultrasonic vibration assisted grinding

    Institute of Scientific and Technical Information of China (English)

    ZHANG; Hong-li; ZHANG; Jian-hua

    2009-01-01

    Separate characteristic of the tangential ultrasonic vibration assisted grinding(TUAG)machining is analyzed based on TUAG process, and a critical speed formula is given to correctly set the machining parameters to insure the separate characteristics of TUAG process. The critical speed is not only related to the ultrasonic vibration amplitude and frequency, but also to the grinding wheel velocity and the cutting point space, and the grinding force can be decreased during the TUAG process with separability. Grinding force experiments are conducted, and the experimental results are in good agreement with the theoretical results.

  2. Study on the New Grinding Fluids of Oils on Water

    Institute of Scientific and Technical Information of China (English)

    魏源迁; 钱怡; 中村隆; 松原十三生

    2003-01-01

    To fulfill a zero-emission in the process of grinding and thoroughly eliminate the influences of the conventional grinding fluids on the eco-environment as well as save up electric energy and reduce in production costs, the new grinding fluids of botanic oils on water were developed, in which a lot of tiny water droplets attached with micro oil films were blown to the machining area by a compressing air-jet so good as to produce lubricating and cooling roles.In this study, grinding performances of the new fluids were investigated by comparison to the conventional ones such as emulsion on the plane NC grinder.

  3. Thermo-mechanical properties of bowl-shaped grinding wheel and machining error compensation for grinding indexable inserts

    Institute of Scientific and Technical Information of China (English)

    张祥雷; 姚斌; 陈彬强; 孙维方; 王萌萌; 罗琪

    2015-01-01

    In order to meet the technical requirements of grinding the circumferential cutting edge of indexable inserts, thermo-mechanical properties of bowl-shaped grinding wheel in high speed grinding process and the influence of dimension variations of the grinding wheel on machining accuracy were investigated. Firstly, the variation trends of the dimension due to centrifugal force generated in different wheel speeds were studied and the effect of stress stiffening and spin softening was presented. Triangular heat flux distribution model was adopted to determine temperature distribution in grinding process. Temperature field cloud pictures were obtained by the finite element software. Then, dimension variation trends of wheel structure were acquired by considering the thermo-mechanical characteristic under combined action of centrifugal force and grinding heat at different speeds. A method of online dynamic monitoring and automatic compensation for dimension error of indexable insert was proposed. By experimental verification, the precision of the inserts satisfies the requirement of processing.

  4. Quenching simulation of steel grinding balls

    Energy Technology Data Exchange (ETDEWEB)

    Zapata-Hernandez, O.; Reyes, L. A.; Camurri, C.; Carrasco, C.; Garza-Monte-de-Oca, F.; Colas, R.

    2015-07-01

    The phase transformations of high carbon steel during quenching and equalizing were modelled using commercial computer packages based on the finite element method and the kinetic transformation of steel. The model was used to predict the temperature and microstructural changes taking place within balls of two different sizes that are used for grinding mineral ores. A good correlation between the temperatures measured by inserted thermocouples and those predicted by the model was obtained after modifying the thermal conductivity of the steel within the temperature domain at which mixed phases are present. The phase transformations predicted were confirmed by metallographic analyses. (Author)

  5. Potential resource and toxicity impacts from metals in waste electronic devices.

    Science.gov (United States)

    Woo, Seung H; Lee, Dae Sung; Lim, Seong-Rin

    2016-04-01

    As a result of the continuous release of new electronic devices, existing electronic devices are quickly made obsolete and rapidly become electronic waste (e-waste). Because e-waste contains a variety of metals, information about those metals with the potential for substantial environmental impact should be provided to manufacturers, recyclers, and disposers to proactively reduce this impact. This study assesses the resource and toxicity (i.e., cancer, noncancer, and ecotoxicity) potentials of various heavy metals commonly found in e-waste from laptop computers, liquid-crystal display (LCD) monitors, LCD TVs, plasma TVs, color cathode ray tube (CRT) TVs, and cell phones and then evaluates such potentials using life cycle impact-based methods. Resource potentials derive primarily from Cu, Sb, Ag, and Pb. Toxicity potentials derive primarily from Pb, Ni, and Hg for cancer toxicity; from Pb, Hg, Zn, and As for noncancer toxicity; and from Cu, Pb, Hg, and Zn for ecotoxicity. Therefore, managing these heavy metals should be a high priority in the design, recycling, and disposal stages of electronic devices.

  6. Development of a mini-tablet of co-grinded prednisone-Neusilin complex for pediatric use.

    Science.gov (United States)

    Lou, H; Liu, M; Wang, L; Mishra, S R; Qu, W; Johnson, J; Brunson, E; Almoazen, H

    2013-09-01

    The purpose of this study is to enhance the dissolution rate of prednisone by co-grinding with Neusilin to form a complex that can be incorporated into a mini-tablet formulation for pediatrics. Prednisone-Neusilin complex was co-grinded at various ratios (1:1, 1:3, 1:5, and 1:7). The physicochemical properties of the complex were characterized by various analytical techniques including: differential scanning calorimetry (DSC), X-ray powder diffraction (XRPD), scanning electron microscope (SEM), particle size, surface area, solubility, and dissolution rate. The co-grinded prednisone-Neusilin complex (1:7) was blended with other excipients and was formulated into a 2-mm diameter mini-tablet. The mini-tablets were further evaluated for thickness, weight, content uniformity, and dissolution rate. To improve taste masking and stability, mini-tablets were coated by dip coating with Eudragit® EPO solution. DSC and XRPD results showed that prednisone was transformed from crystalline state into amorphous state after co-grinding with Neusilin. Particle size, surface area, and SEM results confirmed that prednisone was adsorbed to Neusilin's surface. Co-grinded prednisone-Neusilin complex (1:7) had a solubility of 0.24 mg/mL and 90% dissolved within 20 min as compared to crystalline prednisone which had a solubility of 0.117 mg/mL and 30% dissolved within 20 min. The mini-tablets containing co-grinded prednisone-Neusilin complex (1:7) exhibited acceptable physicochemical and mechanical properties including dissolution rate enhancement. These mini-tablets were successfully dip coated in Eudragit® EPO solution to mask the taste of the drug during swallowing. This work illustrates the potential use of co-grinded prednisone-Neusilin to enhance solubility and dissolution rate as well as incorporation into a mini-tablet formulation for pediatric use.

  7. Model of e-learning with electronic educational resources of new generation

    Directory of Open Access Journals (Sweden)

    A. V. Loban

    2017-01-01

    Full Text Available Purpose of the article: improving of scientific and methodical base of the theory of the е-learning of variability. Methods used: conceptual and logical modeling of the е-learning of variability process with electronic educational resource of new generation and system analysis of the interconnection of the studied subject area, methods, didactics approaches and information and communication technologies means. Results: the formalization complex model of the е-learning of variability with electronic educational resource of new generation is developed, conditionally decomposed into three basic components: the formalization model of the course in the form of the thesaurusclassifier (“Author of e-resource”, the model of learning as management (“Coordination. Consultation. Control”, the learning model with the thesaurus-classifier (“Student”. Model “Author of e-resource” allows the student to achieve completeness, high degree of didactic elaboration and structuring of the studied material in triples of variants: modules of education information, practical task and control tasks; the result of the student’s (author’s of e-resource activity is the thesaurus-classifier. Model of learning as management is based on the principle of personal orientation of learning in computer environment and determines the logic of interaction between the lecturer and the student when determining the triple of variants individually for each student; organization of a dialogue between the lecturer and the student for consulting purposes; personal control of the student’s success (report generation and iterative search for the concept of the class assignment in the thesaurus-classifier before acquiring the required level of training. Model “Student” makes it possible to concretize the learning tasks in relation to the personality of the student and to the training level achieved; the assumption of the lecturer about the level of training of a

  8. Occlusal Grinding Pattern during Sleep Bruxism and Temporomandibular Disorder

    Directory of Open Access Journals (Sweden)

    Yeni Wijaya

    2013-09-01

    Full Text Available Sleep Bruxism is a significant etiology of temporomandibular disorder (TMD and causes many dental or oral problems such as tooth wear or facet. There is no study analyzing the relationship between sleep bruxism and TMD. Objective: To investigate any relationship between occlusal grinding pattern during sleep bruxism and temporomandibular disorder. Methods: A cross-sectional study involving 30 sleep bruxism patients attended the Faculty Dentistry Universitas Indonesia Teaching Hospital (RSGMP FKG UI. Completion of 2 forms of ID-TMD index and questionnaire from American Academy of Sleep Medicine were done. BruxChecker was fabricated and used for two nights to record the occlusal grinding pattern. The occlusal grinding pattern was categorized into laterotrusive grinding (LG and mediotrusive side. Further divisons of LG were: incisor-canine (IC, incisor-caninepremolar (ICP and incisor-canine-premolar-molar (ICPM. Mediotrusive side was classified as mediotrusive contact (MC and mediotrusive grinding (MG. Results: It was found that occlusal grinding pattern in non-TMD subjects were IC+MC, in subjects with mild TMD were ICP+MG and in subjects with moderate TMD were ICP+MG and ICPM+MG. TMJ was more significantly affected by ICP and ICPM grinding pattern than that of IC. Conclusion: There was a significant relationship between occlusal grinding pattern during sleep bruxism and TMD.DOI: 10.14693/jdi.v20i2.149

  9. 7 CFR 58.726 - Cutting and grinding.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 3 2010-01-01 2010-01-01 false Cutting and grinding. 58.726 Section 58.726 Agriculture Regulations of the Department of Agriculture (Continued) AGRICULTURAL MARKETING SERVICE (Standards... Procedures § 58.726 Cutting and grinding. The trimmed and cleaned cheese should be cut into sections...

  10. Stochastic dynamic programming applied to planning of robot grinding tasks

    Energy Technology Data Exchange (ETDEWEB)

    Brown, M.L. (Digital Equipment Corp., Shrewsbury, MA (United States)); Whitney, D.E. (Massachusetts Inst. of Technology, Cambridge, MA (United States))

    1994-10-01

    This paper proposes an intelligent manufacturing system that can make decisions about the process in light of the uncertain outcome of these decisions and attempts to minimize the expected economic penalty resulting from those decisions. It uses robot weld bead grinding as an example of a process with significant process variations. The need for multiple grinding passes, the poor predictability of those passes, the task requirements, and the process constraints conspire to make planning and controlling weld bead grinding a formidable probe. A three tier hierarchical control system is proposed to plan an optimal sequence of grinding passes, dynamically simulate each pass, execute the planned sequence of controlled grinding passes, and modify the pass sequence as grinding continues. The top tier, described in this paper, plans the grinding sequence for each weld bead, and is implemented using Stochastic Dynamic Programming, selecting the volumetric removal and feedspeed for each pass in order to optimize the satisfaction of the task requirements by the entire grinding sequence within the equipment, task, and process constraints. The resulting optimal policies have quite complex structures, showing foresight, anxiety, indifference, and aggressiveness, depending upon the situation.

  11. Integrated Modeling and Intelligent Control Methods of Grinding Process

    Directory of Open Access Journals (Sweden)

    Jie-sheng Wang

    2013-01-01

    Full Text Available The grinding process is a typical complex nonlinear multivariable process with strongly coupling and large time delays. Based on the data-driven modeling theory, the integrated modeling and intelligent control method of grinding process is carried out in the paper, which includes the soft-sensor model of economic and technique indexes, the optimized set-point model utilizing case-based reasoning, and the self-tuning PID decoupling controller. For forecasting the key technology indicators (grinding granularity and mill discharge rate of grinding process, an adaptive soft-sensor modeling method based on wavelet neural network optimized by the improved shuffled frog leaping algorithm (ISFLA is proposed. Then, a set point optimization control strategy of grinding process based on case-based reasoning (CBR method is adopted to obtain the optimized velocity set-point of ore feed and pump water feed in the grinding process controlled loops. Finally, a self-tuning PID decoupling controller optimized is used to control the grinding process. Simulation results and industrial application experiments clearly show the feasibility and effectiveness of control methods and satisfy the real-time control requirements of the grinding process.

  12. Computer Simulation of Batch Grinding Process Based on Simulink 5.0

    Institute of Scientific and Technical Information of China (English)

    LI Xia; YANG Ying-jie; DENG Hui-yong; HUANG Guang-yao

    2005-01-01

    How to use Simulink software in grinding system was studied. The method of designing batch grinding subsystem and the steps of building batch grinding blockset were introduced. Based on batch grinding population balance model, batch grinding was simulated with Simulink. The results show that the simulation system designed with Simulink explain reasonably the impersonal rule of batch grinding. On the basis of batch grinding simulation, the computer simulation of mineral processing system with Simulink of grinding and classification, comminution, etc, can be properly explored.

  13. Three-dimensional measurement and characterization of grinding tool topography

    Science.gov (United States)

    Cui, Changcai; Blunt, Liam; Jiang, Xiangqian; Xu, Xipeng; Huang, Hui; Ye, Ruifang

    2013-01-01

    A comprehensive 3-dimensional measurement and characterization method for grinding tool topography was developed. A stylus instrument (SOMICRONIC, France) was used to measure the surface of a metal-bonded diamond grinding tool. The sampled data was input the software SurfStand developed by Centre for Precision Technology (CPT) for reconstruction and further characterization of the surface. Roughness parameters pertaining to the general surface and specific feature parameters relating to the grinding grits, such as height and angle peak curvature have been calculated. The methodology of measurement has been compared with that using an optical microscope. The comparison shows that the three-dimensional characterization has distinct advantages for grinding tool topography assessment. It is precise, convenient and comprehensive so it is suitable for precision measurement and analysis where an understanding of the grinding tool and its cutting ability are required.

  14. Monitoring Grinding Wheel Redress-life Using Support Vector Machines

    Institute of Scientific and Technical Information of China (English)

    Xun Chen; Thitikorn Limchimchol

    2006-01-01

    Condition monitoring is a very important aspect in automated manufacturing processes. Any malfunction of a machining process will deteriorate production quality and efficiency. This paper presents an application of support vector machines in grinding process monitoring. The paper starts with an overview of grinding behaviour. Grinding force is analysed through a Short Time Fourier Transform (STFT) to identify features for condition monitoring. The Support Vector Machine (SVM) methodology is introduced as a powerful tool for the classification of different wheel wear situations.After training with available signal data, the SVM is able to identify the state of a grinding process. The requirement and strategy for using SVM for grinding process monitoring is discussed, while the result of the example illustrates how effective SVMs can be in determining wheel redress-life.

  15. Specific Properties of Air Flow Field Within the Grinding Zone

    Institute of Scientific and Technical Information of China (English)

    ZHENG Junyi; JIANG Zhengfeng; ZHAO Liang

    2006-01-01

    Air barrier of grinding means a boundary layer of air existing at the circumference of the rotating wheel, which hinders coolant from entry. This paper makes a research on air flow field of the grinding zone through experiments and numerical simulations, focusing on acquainting with the specific properties of the air flow field. Finite volume method is applied to analyze air flow field within grinding wheel in the course of numerical calculations. The test devices such as Hot-wire anemometer and Betz manometer are used during the experiments of testing the pressure and velocity within grinding zone. Results of experiments agree by and large with numerical results of calculations. The conclusions obtained in this paper, the distribution of wall pressure and the distribution of air flow velocity, are important and useful to navigate the delivery of coolant into the grinding zone. In conclusion, some recommendations are made for further study and practical applications in such field.

  16. Research on product size and grinding dynamics of vibration mills

    Institute of Scientific and Technical Information of China (English)

    YIN Zhong-jun; HAN Tian; CHEN Bing; ZHANG Wen-zhong

    2007-01-01

    In order to improve vibration mills grinding effect and increase productive efficiency, prime factors of vibration mills were gained much attention. The purpose of this study is to reveal product size distribution and grinding dynamics of vibration mills by orthogonal experi-ments. The metallurgical refractory materials were used as research object. In order to explore the relationships between grinding effect and primary factors, lots of milling experiments were carried out. Based on the results, the conclusions can be summarized: as time runs, the size distri-bution shows exponential trend, and range becomes more and more narrow. Also the quantitative analysis result between grinding effect and primary factors was obtained by non-linear regres-sion: high frequency, high amplitude and low fill ratio can increase grinding speed.

  17. The effect of grinding on the mechanical behavior of Y-TZP ceramics: A systematic review and meta-analyses

    NARCIS (Netherlands)

    Pereira, G.K.R.; Fraga, S.; Montagner, A.F.; Soares, F.Z.M.; Kleverlaan, C.J.; Valandro, L.F.

    2016-01-01

    The aim of this study was to systematically review the literature to assess the effect of grinding on the mechanical properties, structural stability and superficial characteristics of Y-TZP ceramics. The MEDLINE via PubMed and Web of Science (ISI – Web of Knowledge) electronic databases were search

  18. [Use of internet and electronic resources among Spanish intensivist physicians. First national survey].

    Science.gov (United States)

    Gómez-Tello, V; Latour-Pérez, J; Añón Elizalde, J M; Palencia-Herrejón, E; Díaz-Alersi, R; De Lucas-García, N

    2006-01-01

    Estimate knowledge and use habits of different electronic resources in a sample of Spanish intensivists: Internet, E-mail, distribution lists, and use of portable electronic devices. Self-applied questionnaire. A 50-question questionnaire was distributed among Spanish intensivists through the hospital marketing delegates of a pharmaceutical company and of electronic forums. A total of 682 questionnaires were analyzed (participation: 74%). Ninety six percent of those surveyed used Internet individually: 67% admitted training gap. Internet was the second source of clinical consultations most used (61%), slightly behind consultation to colleagues (65%). The pages consulted most were bibliographic databases (65%) and electronic professional journals (63%), with limited use of Evidence Based Medicine pages (19%). Ninety percent of those surveyed used e-mail regularly in the practice of their profession, although 25% admitted that were not aware of its possibilities. The use of E-mail decreased significantly with increase in age. A total of 62% of the intensivists used distribution lists. Of the rest, 42% were not aware of its existence and 32% admitted they had insufficient training to handle them. Twenty percent of those surveyed had portable electronic devices and 64% considered it useful, basically due to its rapid consultation at bedside. Female gender was a negative predictive factor of its use (OR 0.35; 95% CI 0.2-0.63; p=0.0002). A large majority of the Spanish intensivists use Internet and E-mail. E-mail lists and use of portable devices are still underused resources. There are important gaps in training and infrequent use of essential pages. There are specific groups that require directed educational policies.

  19. Review of material recovery from used electric and electronic equipment-alternative options for resource conservation.

    Science.gov (United States)

    Friege, Henning

    2012-09-01

    For waste from electric and electronic equipment, the WEEE Directive stipulates the separate collection of electric and electronic waste. As to new electric and electronic devices, the Restriction of Hazardous Substances (RoHS) Directive bans the use of certain chemicals dangerous for man and environment. From the implementation of the WEEE directive, many unsolved problems have been documented: poor collection success, emission of dangerous substances during collection and recycling, irretrievable loss of valuable metals among others. As to RoHS, data from the literature show a satisfying success. The problems identified in the process can be reduced to some basic dilemmas at the borders between waste management, product policy and chemical safety. The objectives of the WEEE Directive and the specific targets for use and recycling of appliances are not consistent. There is no focus on scarce resources. Extended producer responsibility is not sufficient to guarantee sustainable waste management. Waste management reaches its limits due to problems of implementation but also due to physical laws. A holistic approach is necessary looking at all branch points and sinks in the stream of used products and waste from electric and electronic equipment. This may be done with respect to the general rules for sustainable management of material streams covering the three dimensions of sustainable policy. The relationships between the players in the field of electric and electronic devices have to be taken into account. Most of the problems identified in the implementation process will not be solved by the current amendment of the WEEE Directive.

  20. Investigations of spherical grinding parameters on circularity error, finished diameter, and grinding forces for porous polyurethane foam

    Directory of Open Access Journals (Sweden)

    Isarawit Chaopanich

    2010-07-01

    Full Text Available The aim of this study was to examine the effect of grinding variables on the circularity error, finished diameter, andgrinding forces of porous polyurethane foam (PPUF. A cube of PPUF having the size of 21 mm was transformed into a roundshape using a vertical wheel grinding with the circular groove pad developed. The grinding speed (Vs of the wheel wasvaried between 1.41 and 5.18 m/s. The cross head speed of the circular groove pad (f was controlled at 1, 3, 5 mm/min. Theabrasive grit size (A of 20 and 53 μm made of silicon carbide were applied. Two replications of experiment were randomlyperformed. Diameter and circularity error of the ground specimen were determined by vision measuring machine. The tangentialand normal forces of grinding were obtained using a dynamometer. The experimental data were statistically analyzed. The study found that (1 the grinding speed could remarkably affect the circularity error, finished diameter, and grinding forces,(2 the grinding speed ranged between 2.83 and 3.77 m/s could contribute to sphere shape specimens, and (3 the grinding speed of 3.30 m/s, cross head speed of 1 mm/min, and abrasive grit size of 20 μm provided the least circularity error.

  1. Aufwand und Nutzen des Electronic Resource Management Systems RMS an der UB Kassel

    Directory of Open Access Journals (Sweden)

    Tobias Pohlmann

    2016-03-01

    The university library of Kassel therefore uses SemperTool’s web-based electronic resource management system RMS. This paper presents the functionality of this system and makes an estimate of the expenditure of work necessary to enter all relevant information about licensed databases, e-book and e-journal packages with the corresponding individual resources. It also describes existing and projected tools for analysis and evaluation, which are decisive for the usefulness of such a system, and concludes with the satisfaction reached at the university library of Kassel. These experiences may help other libraries to decide whether or not to introduce RMS or a comparable system.

  2. Morphology of Near- and Semispherical Melted Chips after the Grinding Processes Using Sol-Gel Abrasives Based on SEM-Imaging and Analysis

    Directory of Open Access Journals (Sweden)

    W. Kapłonek

    2016-01-01

    Full Text Available Selected issues related to SEM-imaging and image analysis of spherical melted chips formed during the grinding process are presented and discussed. The general characteristics of this specific group of machining products are given. Chip formation phenomena, as well as their overall morphology, are presented using selected examples of near- and semispherical melted chips occurring singly or concentrated in clusters on the grinding wheel surface after the machining process. Observation of the spherical melted chips and acquisition of their images were carried out for grinding wheel active surfaces with microcrystalline sintered corundum abrasive grains SG™ after the internal cylindrical grinding process of a 100Cr6 steel and Titanium Grade 2® alloy by use of a scanning electron microscope, JEOL JSM-5500LV. Analysis of the obtained SEM micrographs was carried out by Image-Pro® Plus 5.0 software to determine the selected geometrical parameters describing the morphological features of the assessed chips.

  3. ELECTRONIC EDUCATIONAL RESOURCES FOR ONLINE SUPPORT OF MODERN CHEMISTRY CLASSES IN SPECIALIZED SCHOOL

    Directory of Open Access Journals (Sweden)

    Maria D. Tukalo

    2013-09-01

    Full Text Available This article contains material of some modern electronic educational resources that can be used via the Internet to support the modern chemistry classes in specialized school. It was drawn attention to the educational chemical experiments as means of knowledge; simulated key motivational characteristics to enhance students interest for learning subjects, their cognitive and practical activity in the formation of self-reliance and self-creative; commented forecasts for creating of conditions to enhance the creative potential of students in a modern learning environment.

  4. Numerical Simulation of a Grinding Process for the Spatial Work-pieces: Modeling of Grinding Forces and System Dynamics

    Directory of Open Access Journals (Sweden)

    I. A. Kiselev

    2015-01-01

    Full Text Available The paper describes a computation-experimental technique to determine model coefficients of grinding forces using a Nelder-Mead algorithm. As an error function, the paper offers a deviation measure of calculating and experimental grinding forces averaged for a single-pass of the grinding wheel. As an example of cutting forces model coefficients calculation for linear model, in which the grinding forces depend on uncut chip thickness is analyzed. The coefficients vary on abrasive grain geometric parameters and are determined applying the authors-developed method based on Nelder-Mead technique. The measured forces while plane grinding of test work-piece are used to determine the coefficients. Model coefficients are identified if compare the measured data with the results of modeling for grinding by tool with the uniformly distributed abrasive grains with the triangular shape of cutting edge.Grinding dynamics simulation applying the determined coefficients was carried out for the processing of cantilever plane work-piece as a test example. The work-piece was processed by grinding wheel transverse passages made at different distances from the fixation. A selfoscillating process accompanied by vibration of high level was observed for some selected technological parameters of grinding. The simulation has shown qualitative and quantitative compliance with the experiment. It was shown that the intensity of the self-oscillating process arising during the processing depends on the work-piece rigidity and cutting conditions. The results of modeling can be applied in practice in developing the technology process of grinding the spatial work-pieces.

  5. Investigation on drilling-grinding of CFRP

    Institute of Scientific and Technical Information of China (English)

    Yanming QUAN; Wenwang ZHONG

    2009-01-01

    It is difficult to machine polymer matrix composites reinforced by carbon fibre, and the hole-making process is the most necessary machining process for composite plate products. Conventional drills have a very short life in the drilling of this kind of composites and the quality of the hole is very poor. In this paper, the cemented or plated diamond core tools are tested to make holes in carbon fibre/epoxy composite plates. The effects of machining parameters, cooling and chip removal on the tool life, and the hole quality are investigated. The results indicate that the material removal mechanism of the two kinds of diamond tools is not like the cutting effect of the conventional drilling but similar to that of grinding. Satisfactory effects in making holes in the composites are obtained--quite acceptable machined hole quality, low costs, and long wear-resistant endurance.

  6. Modelling and simulation of fixtures during grinding

    Institute of Scientific and Technical Information of China (English)

    Matthias; KLAERNER; Juergen; LEOPOLD; Lothar; KROLL

    2009-01-01

    The complex workpiece-fixture behaviour during machining is an essential component of the fixture development process.In detail,the forces acting on fixture components have to be analysed.A method for the prediction of the reaction forces due to process and clamping loads is presented in this article.At the beginning,detailed information about the workpiece-fixture behaviour during the process is determined by a complex finite element model.Secondly,the reduction of the number of elements leads to a smaller model with less computation time,validated and used for the variation of process parameters.Finally,an analytical description is developed based on the combination of both results.With the help of the empiric equation it is possible to predict the reaction forces and the dependency on several process parameters.This method has been validated by modelling shape grinding of a nozzle guide vane.

  7. Modelling and simulation of fixtures during grinding

    Institute of Scientific and Technical Information of China (English)

    Matthias KLAERNER; Juergen LEOPOLD; Lothar KROLL

    2009-01-01

    The complex workpiece-fixture behaviour during machining is an essential component of the fixture development process. In detail, the forces acting on fixture components have to be analysed. A method for the prediction of the reaction forces due to process and clamping loads is presented in this article.At the beginning, detailed information about the workpiece-fixture behaviour during the process is determined by a complex finite element model. Secondly, the reduction of the number of elements leads to a smaller model with less computation time, validated and used for the variation of process parameters. Finally, an analytical description is developed based on the combination of both results.With the help of the empiric equation it is possible to predict the reaction forces and the dependency on several process parameters. This method has been validated by modelling shape grinding of a nozzle guide vane.

  8. Continuous grinding mill simulation using Austin's model

    Directory of Open Access Journals (Sweden)

    André Carlos Silva

    2012-01-01

    Full Text Available Comminution is a frequently-required step in mineral processing and is responsible for almost 90% of all energy consumption in a mineral processing plant. Tumbling mill design has been studied since the middle of the XIX century. There are many comminution models in the literature, with preponderance, however, of Austin’s model (2002 for mineral impact breakage. In this paper, Austin’s model was applied to tubular tumbling mills. Once Austin's model was proposed for batch processing of narrowly-distributed fraction sizes, an artifice has allowed it to be used in continuous grinding mill processes with widely-distributed fraction sizes. Interesting results were obtained with errors less than 0.005 for mills with sharp residence time distributions.

  9. Grinding Characteristic of Multi-walled Carbon Nanotubes-alumina Composite Particle

    Institute of Scientific and Technical Information of China (English)

    B MUNKHBAYAR; Nasan BAYARAA; Hafizur REHMAN; Junhyo KIM; Hanshik CHUNG; Hyomin JEONG

    2012-01-01

    The synthesis of new materials containing multi-walled carbon nanotubes (MWCNTs) and the microstructure of alumina particles were investigated and characterized.The MWCNTs and alumina particles were ground under both the dry and wet conditions with various rotation speeds (200-400 r/min) in planetary ball milling machine,and their combination characteristics were described.The experimental results were examined by scanning electron microscopy (SEM),X-ray diff action (XRD),transmission electron microscopy (TEM) and particle sizing analysis (PSA).SEM result revealed that the combination of MWCNTs -Alumina particles mixed quite well under both the dry and wet grinding with rotation speed of 400 r/min.XRD characterization indicated the better result could get in ground samples at a rotation speed of 400 r/min.PSA result showed the particle size decreased with increase the grinding speeds.From the overall results,we observed that the grinding method can be used to synthesize new material with high efficiency.

  10. Experimental Studies on Ultrasonic Vibration Grinding of the Workpiece Made from Fine-crystalline Zirconia Ceramics

    Institute of Scientific and Technical Information of China (English)

    WU Yan; ZHU Xun-sheng; ZHAO Bo

    2006-01-01

    The performances of fine-crystalline zirconia ceramics in workpiece ultrasonic vibration grinding (WUVG) and conventional grinding (CG) with diamond wheel were researched. The effects of WUVG and CG on material removal rate, grinding forces, surface roughness and microstructure of zirconia ceramic were investigated.Experimental results indicated that: (1) The material removal rate (MRR) in ultrasonic grinding process is two times as large as that of in conventional grinding. The material removal rate increases with increasing grinding depth in both ultrasonic grinding and conventional grinding.(2) The ultrasonic vibration grinding force is lower than that of conventional grinding force, and the increase of the worktable speed leads to a decrease of the grinding force,while the grinding force increases with larger grinding depth in both WUVG and CG. (3) The surface of ultrasonic vibration grinding has no spur and build-up edge and its surface roughness is smaller than that of CG significantly.Surface quality of WUVG is superior to that of conventional grinding, it is easy for ultrasonic vibration grinding that material removal mechanism is ductile grinding.

  11. Grinding temperature and energy ratio coe cient in MQL grinding of high-temperature nickel-base alloy by using di erent vegetable oils as base oil

    Institute of Scientific and Technical Information of China (English)

    Li Benkai; Li Changhe; Zhang Yanbin; Wang Yaogang; Jia Dongzhou; Yang Min

    2016-01-01

    Vegetable oil can be used as a base oil in minimal quantity of lubrication (MQL). This study compared the performances of MQL grinding by using castor oil, soybean oil, rapeseed oil, corn oil, sunflower oil, peanut oil, and palm oil as base oils. A K-P36 numerical-control precision surface grinder was used to perform plain grinding on a workpiece material with a high-temperature nickel base alloy. A YDM–III 99 three-dimensional dynamometer was used to measure grinding force, and a clip-type thermocouple was used to determine grinding temperature. The grinding force, grind-ing temperature, and energy ratio coefficient of MQL grinding were compared among the seven veg-etable oil types. Results revealed that (1) castor oil-based MQL grinding yields the lowest grinding force but exhibits the highest grinding temperature and energy ratio coefficient;(2) palm oil-based MQL grinding generates the second lowest grinding force but shows the lowest grinding temperature and energy ratio coefficient;(3) MQL grinding based on the five other vegetable oils produces similar grinding forces, grinding temperatures, and energy ratio coefficients, with values ranging between those of castor oil and palm oil;(4) viscosity significantly influences grinding force and grinding tem-perature to a greater extent than fatty acid varieties and contents in vegetable oils;(5) although more viscous vegetable oil exhibits greater lubrication and significantly lower grinding force than less vis-cous vegetable oil, high viscosity reduces the heat exchange capability of vegetable oil and thus yields a high grinding temperature;(6) saturated fatty acid is a more efficient lubricant than unsaturated fatty acid;and (7) a short carbon chain transfers heat more effectively than a long carbon chain. Palm oil is the optimum base oil of MQL grinding, and this base oil yields 26.98 N tangential grinding force, 87.10 N normal grinding force, 119.6 °C grinding temperature, and 42.7%energy ratio coefficient

  12. Teachers' Link to Electronic Resources in the Library Media Center: A Local Study of Awareness, Knowledge, and Influence

    Science.gov (United States)

    Williams, Teresa D.; Grimble, Bonnie J.; Irwin, Marilyn

    2004-01-01

    High school students often use online databases and the Internet in the school library media center (SLMC) to complete teachers' assignments. This case study used a survey to assess teachers' awareness of electronic resources, and to determine whether their directions influence student use of these resources in the SLMC. Participants were teachers…

  13. Impact of Knowledge Resources Linked to an Electronic Health Record on Frequency of Unnecessary Tests and Treatments

    Science.gov (United States)

    Goodman, Kenneth; Grad, Roland; Pluye, Pierre; Nowacki, Amy; Hickner, John

    2012-01-01

    Introduction: Electronic knowledge resources have the potential to rapidly provide answers to clinicians' questions. We sought to determine clinicians' reasons for searching these resources, the rate of finding relevant information, and the perceived clinical impact of the information they retrieved. Methods: We asked general internists, family…

  14. Frequency domain identification of grinding stiffness and damping

    Science.gov (United States)

    Leonesio, Marco; Parenti, Paolo; Bianchi, Giacomo

    2017-09-01

    As equivalent stiffness and damping of the grinding process dominate cutting stability, their identification is essential to predict and avoid detrimental chatter occurrence. The identification of these process constants is not easy in large cylindrical grinding machines, e.g. roll grinders, since there are no practical ways to measure cutting force normal component. This paper presents a novel frequency domain approach for identifying these process parameters, exploiting in-process system response, measured via impact testing. This method adopts a sub-structuring approach to couple the wheel-workpiece relative dynamic compliance with a two-dimensional grinding force model that entails both normal and tangential directions. The grinding specific energy and normal force ratio, that determine grinding stiffness and damping, are identified by fitting the closed loop FRF (Frequency Response Function) measured during specific plunge-grinding tests. The fitting quality supports the predictive capability of the model. Eventually, the soundness of the proposed identification procedure is further assessed by comparing the grinding specific energy identified through standard cutting power measurements.

  15. Ultraprecision, high stiffness CNC grinding machines for ductile mode grinding of brittle materials

    Science.gov (United States)

    McKeown, Patrick A.; Carlisle, Keith; Shore, Paul; Read, R. F.

    1990-10-01

    Under certain controlled conditions it is now possible to machine brittle materials such as glasses and ceramics using single or multi-point diamond tools (grinding), so that material is removed by plastic flow, leaving crack-free surfaces. This process is called 'shear' or 'ductile' mode grinding. It represents a major breakthrough in modern manufacturing engineering since it promises to enable: - complex optical components, both transmission and reflecting to be generated by advanced CNC machines with very little (or even zero) subsequent polishing. - complex shaped components such as turbine blades, nozzle guide vanes, etc. to be finish machined after near net shape forming, to high precision in advanced ceramics such as silicon nitride, without inducing micro-cracking and thus lowering ultimate rupture strength and fatigue life. Ductile mode "damage free" grinding occurs when the volume of materials stressed by each grit of the grinding wheel is small enough to yield rather than exhibit brittle fracture, i.e. cracking. In practice, this means maintaining the undeformed chip thickness to below the ductile-brittle transition value; this varies from material to material but is generally in the order of 0.1 pm or 100 nm, (hence the term "nanogrinding" is sometimes used) . Thus the critical factors for operating successfully in the ductile regime are machine system accuracy and dynamic stiffness between each grit and the workpiece. In detail this means: (i) High precision 'truing' of the diamond grits, together with dressing of the wheel bond to ensure adequate ' openness'; (ii) Design and build of the grinding wheel spindle with very high dynamic stiffness; error motions, radial and axial, must be considerably less than 100 nfl. (iii) Design and build of the workpiece carriage motion system with very high dynamic stiffness; error motions, linear or rotary, must be well within 100 nm. (iv) Smooth, rumble-free, high-stiffness servo-drives controlling the motions

  16. McCarter superfinish grinding for silicon -- an update.

    Energy Technology Data Exchange (ETDEWEB)

    Anthony, F.; Khounsary, A.; McCarter, D.; Krasnicki, F.; Tangedahl, M.

    2000-11-03

    A grinding technique, referred to as the McCarter Superfinish, for grinding large size optical components is discussed and certain surface characterization information about flatness and the relative magnitude of the subsurface damage in silicon substrates is reported. The flatness measurements were obtained with a Zygo surface analyzer, and the substrate damage measurements were made by x-ray diffraction and acid etching. Results indicate excellent control of flatness and fine surface finish. X-ray measurements show that the diamond wheels with small particle sizes used in the final phases of the grinding operation renders surfaces with relatively small subsurface damage.

  17. Effect of wet grinding on structural properties of ball clay

    Science.gov (United States)

    Purohit, A.; Hameed, A.; Chander, S.; Nehra, S. P.; Singh, P.; Dhaka, M. S.

    2015-05-01

    In this paper, the effect of wet grinding on structural properties of ball clay is undertaken. The wet grinding treatment was performed employing ball and vibro mills for different time spells of 2, 4, 8 and 16 hours. The structural properties were carried out using X-ray diffraction (XRD). The structure of ground samples is found to be simple cubic. The crystallographic parameters are calculated and slight change in lattice constant, inter planner spacing and particle size is observed with grinding treatment. The results are in agreement with the available literature.

  18. Investigation on the Surface Coating of Grinding Balls

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The surface coating of grinding balls was investigated experimentally. The results show that a coating may form on the surface of grinding balls when Cr or Al powders are subjected to ball grinding. The plastic deformation of the ball surface plays an important role during the coating formation, and the strong binding force between the powders and the balls is a necessary pre-condition. The thickness of coating increases with the plasticity of the powders and the balls. Annealing the balls with coating will result in an obvious diffusion of the elements in the bonding zone of inter-face.

  19. Eco-efficiency of grinding processes and systems

    CERN Document Server

    Winter, Marius

    2016-01-01

    This research monograph aims at presenting an integrated assessment approach to describe, model, evaluate and improve the eco-efficiency of existing and new grinding processes and systems. Various combinations of grinding process parameters and system configurations can be evaluated based on the eco-efficiency. The book presents the novel concept of empirical and physical modeling of technological, economic and environmental impact indicators. This includes the integrated evaluation of different grinding process and system scenarios. The book is a valuable read for research experts and practitioners in the field of eco-efficiency of manufacturing processes but the book may also be beneficial for graduate students.

  20. Reducing Clinical Trial Monitoring Resource Allocation and Costs Through Remote Access to Electronic Medical Records

    Science.gov (United States)

    Uren, Shannon C.; Kirkman, Mitchell B.; Dalton, Brad S.; Zalcberg, John R.

    2013-01-01

    Purpose: With electronic medical records (eMRs), the option now exists for clinical trial monitors to perform source data verification (SDV) remotely. We report on a feasibility study of remote access to eMRs for SDV and the potential advantages of such a process in terms of resource allocation and cost. Methods: The Clinical Trials Unit at the Peter MacCallum Cancer Centre, in collaboration with Novartis Pharmaceuticals Australia, conducted a 6-month feasibility study of remote SDV. A Novartis monitor was granted dedicated software and restricted remote access to the eMR portal of the cancer center, thereby providing an avenue through which perform SDV. Results: Six monitoring visits were conducted during the study period, four of which were performed remotely. The ability to conduct two thirds of the monitoring visits remotely in this complex phase III study resulted in an overall cost saving to Novartis. Similarly, remote monitoring eased the strain on internal resources, particularly monitoring space and hospital computer terminal access, at the cancer center. Conclusion: Remote access to patient eMRs for SDV is feasible and is potentially an avenue through which resources can be more efficiently used. Although this feasibility study involved limited numbers, there is no limit to scaling these processes to any number of patients enrolled onto large clinical trials. PMID:23633977

  1. Electronic theses and dissertations: a review of this valuable resource for nurse scholars worldwide.

    Science.gov (United States)

    Goodfellow, L M

    2009-06-01

    A worldwide repository of electronic theses and dissertations (ETDs) could provide worldwide access to the most up-to-date research generated by masters and doctoral students. Until that international repository is established, it is possible to access some of these valuable knowledge resources. ETDs provide a technologically advanced medium with endless multimedia capabilities that far exceed the print and bound copies of theses and dissertations housed traditionally in individual university libraries. CURRENT USE: A growing trend exists for universities worldwide to require graduate students to submit theses or dissertations as electronic documents. However, nurse scholars underutilize ETDs, as evidenced by perusing bibliographic citation lists in many of the research journals. ETDs can be searched for and retrieved through several digital resources such as the Networked Digital Library of Theses and Dissertations (http://www.ndltd.org), ProQuest Dissertations and Theses (http://www.umi.com), the Australasian Digital Theses Program (http://adt.caul.edu.au/) and through individual university web sites and online catalogues. An international repository of ETDs benefits the community of nurse scholars in many ways. The ability to access recent graduate students' research electronically from anywhere in the world is advantageous. For scholars residing in developing countries, access to these ETDs may prove to be even more valuable. In some cases, ETDs are not available for worldwide access and can only be accessed through the university library from which the student graduated. Public access to university library ETD collections is not always permitted. Nurse scholars from both developing and developed countries could benefit from ETDs.

  2. Fundamentals of grinding : surface conditions of ground WC-Co systems

    NARCIS (Netherlands)

    Hegeman, JBJW; De Hosson, JTM; Shulepov, SY; Lousberg, N; de With, G; Brebbia, CA; Kenny, JM

    1999-01-01

    This paper concentrates on the fundamentals of grinding of inorganic materials. A statistical grinding model was developed based on the topography of the grinding wheel. The results of the model are compared with the results of grinding experiments on WC-Co hardmetals. The calculated profiles and me

  3. A preliminary categorization of end-of-life electrical and electronic equipment as secondary metal resources.

    Science.gov (United States)

    Oguchi, Masahiro; Murakami, Shinsuke; Sakanakura, Hirofumi; Kida, Akiko; Kameya, Takashi

    2011-01-01

    End-of-life electrical and electronic equipment (EEE) has recently received attention as a secondary source of metals. This study examined characteristics of end-of-life EEE as secondary metal resources to consider efficient collection and metal recovery systems according to the specific metals and types of EEE. We constructed an analogy between natural resource development and metal recovery from end-of-life EEE and found that metal content and total annual amount of metal contained in each type of end-of-life EEE should be considered in secondary resource development, as well as the collectability of the end-of-life products. We then categorized 21 EEE types into five groups and discussed their potential as secondary metal resources. Refrigerators, washing machines, air conditioners, and CRT TVs were evaluated as the most important sources of common metals, and personal computers, mobile phones, and video games were evaluated as the most important sources of precious metals. Several types of small digital equipment were also identified as important sources of precious metals; however, mid-size information and communication technology (ICT) equipment (e.g., printers and fax machines) and audio/video equipment were shown to be more important as a source of a variety of less common metals. The physical collectability of each type of EEE was roughly characterized by unit size and number of end-of-life products generated annually. Current collection systems in Japan were examined and potentially appropriate collection methods were suggested for equipment types that currently have no specific collection systems in Japan, particularly for video games, notebook computers, and mid-size ICT and audio/video equipment.

  4. From Millennium ERM to Proquest 360 Resource Manager: Implementing a new Electronic Resources Management System ERMS in an International Graduate Research University in Saudi Arabia

    KAUST Repository

    Ramli, Rindra M.

    2017-05-17

    An overview of the Recommendation Study and the subsequent Implementation of a new Electronic Resources Management system ERMS in an international graduate research university in the Kingdom of Saudi Arabia. It covers the timeline, deliverables and challenges as well as lessons learnt by the Project Team.

  5. Innovative grinding wheel design for cost-effective machining of advanced ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Licht, R.H.; Kuo, P.; Liu, S.; Murphy, D.; Picone, J.W.; Ramanath, S.

    2000-05-01

    This Final Report covers the Phase II Innovative Grinding Wheel (IGW) program in which Norton Company successfully developed a novel grinding wheel for cost-effective cylindrical grinding of advanced ceramics. In 1995, Norton Company successfully completed the 16-month Phase I technical effort to define requirements, design, develop, and evaluate a next-generation grinding wheel for cost-effective cylindrical grinding of advanced ceramics using small prototype wheels. The Phase II program was initiated to scale-up the new superabrasive wheel specification to larger diameters, 305-mm to 406-mm, required for most production grinding of cylindrical ceramic parts, and to perform in-house and independent validation grinding tests.

  6. Laser-assisted Grinding Wheel Dressing (Ⅱ)-Experimental Researches

    Institute of Scientific and Technical Information of China (English)

    Ming CHEN; Fanghong SUN; Youngmoon LEE; Seunghan YANG; Jongchan LEE

    2003-01-01

    Most of the mechanical dressing technologies for resin bonded superabrasive grinding wheels are time consumingand costly. Based on the outcomes of the simulations in the previous study, this paper demonstrates the comprehensive researches on the laser-ass

  7. Gemstone Grinding Process Improvement by using Impedance Force Control

    Directory of Open Access Journals (Sweden)

    Hamprommarat Chumpol

    2015-01-01

    Full Text Available Chula Automatic Faceting Machine has been developed by The Advance Manufacturing Research Lab, Chulalongkorn University to support Thailand Gems-Industry. The machine has high precision motion control by using position and force control. A contact stiffness model is used to estimate grinding force. Although polished gems from the Faceting Machine have uniform size and acceptable shape, the force of the grinding and polishing process cannot be maintain constant and has some fluctuation due to indirect force control. Therefor this research work propose a new controller for this process based on an impedance direct force control to improve the gemstone grinding performance during polishing process. The grinding force can be measured through motor current. The results show that the polished gems by using impedance direct force control can maintain uniform size as well as good shape and high quality surface.

  8. Grinding efficiency improvement of hydraulic cylinders parts for mining equipment

    Directory of Open Access Journals (Sweden)

    Korotkov Aleksandr

    2017-01-01

    Full Text Available The aim of the article is to find out ways to improve parts treatment and components of mining equipment on the example of hydraulic cylinders parts, used as pillars for mine roof supports, and other actuator mechanisms. In the course of the research work methods of machine retaining devices design were used, the scientific approaches for the selection of progressive grinding schemes were applied; theoretical and practical experience in the design and production of new constructions of grinding tools was used. As a result of this work it became possible to create a progressive construction of a machine retaining device for grinding of large parts of hydraulic cylinders, to apply an effective scheme of rotary abrasive treatment, to create and implement new design of grinding tools by means of grains with controllable shape and orientation. Implementation of the results obtained in practice will improve the quality and performance of repairing and manufacturing of mining equipment.

  9. E-Records a Grind for Many Doctors

    Science.gov (United States)

    ... page: https://medlineplus.gov/news/fullstory_160789.html E-Records a Grind for Many Doctors And this ... direct contact with patients and 37 percent on E-health records and other clerical work, the study ...

  10. Influence of ageing, grinding and preheating on the thermal behaviour of alpha-lactose monohydrate.

    Science.gov (United States)

    Garnier, S; Petit, S; Mallet, F; Petit, M-N; Lemarchand, D; Coste, S; Lefebvre, J; Coquerel, G

    2008-09-01

    It is shown that the onset temperature and the magnitude of thermal events observed during DSC analyses of alpha-lactose monohydrate can be strongly affected by various treatments such as ageing, manual grinding and preheating (cycle of preliminary dehydration and rehydration). In the case of grinding and preheating, the change of dehydration pathways was further investigated by using a suitable combination of characterization techniques, including X-ray powder diffraction (XRPD) performed with a synchrotron source (allowing an accurate Rietveld analysis), scanning electron microscopy (SEM), laser particle size measurements, FTIR spectroscopy and (1)H NMR for the determination of beta-lactose contents in samples. It appeared that the dehydration mechanism is affected not only by a smaller particle size distribution, but also by residual anisotropic lattice distortions and by the formation of surface defects or high energy surfaces. The fusion-recrystallization process occurring between anhydrous forms of alpha-lactose at ca. 170 degrees C is not significantly affected by grinding, whereas a preheating treatment induces an unexpected large increase of the enthalpy associated with this transition. Our observations and interpretations confirm the important role of water molecules in the crystal cohesion of the title compound and illustrate the necessity to consider the history of each sample for a satisfactory understanding of the physical properties and the behaviour of this important pharmaceutical excipient.

  11. Development of database and searching system for tool grinding

    Directory of Open Access Journals (Sweden)

    J.Y. Chen

    2008-02-01

    Full Text Available Purpose: For achieving the goal of saving time on the tool grinding and design, an efficient method of developing the data management and searching system for the standard cutting tools is proposed in this study.Design/methodology/approach: At first the tool grinding software with open architecture was employed to design and plan grinding processes for seven types of tools. According to the characteristics of tools (e.g. types, diameter, radius and so on, 4802 tool data were established in the relational database. Then, the SQL syntax was utilized to write the searching algorithms, and the human machine interfaces of the searching system for the tool database were developed by C++ Builder.Findings: For grinding a square end mill with two-flute, a half of time on the tool design and the change of production line for grinding other types of tools can be saved by means of our system. More specifically, the efficiency in terms of the approach and retract time was improved up to 40%, and an improvement of approximately 10.6% in the overall machining time can be achieved.Research limitations/implications: In fact, the used tool database in this study only includes some specific tools such as the square end mill. The step drill, taper tools, and special tools can also be taken into account in the database for future research.Practical implications: The most commercial tool grinding software is the modular-based design and use tool shapes to construct the CAM interface. Some limitations on the tool design are undesirable for customers. On the contrary, employing not only the grinding processes to construct the grinding path of tools but the searching system combined with the grinding software, it gives more flexible for one to design new tools.Originality/value: A novel tool database and searching system is presented for tool grinding. Using this system can save time and provide more convenience on designing tools and grinding. In other words, the

  12. Effects of Jet Pressure on the Ground Surface Quality and CBN Wheel Wear in Grinding AISI 690 Nickel-Based Superalloy

    Science.gov (United States)

    Guitouni, Ahmed; Chaieb, Iheb; Rhouma, Amir Ben; Fredj, Nabil Ben

    2016-09-01

    Fluid application in grinding is getting attention as higher stock removal rates, higher surface integrity and longer wheel life are required. It is necessary to define proper conditions of application for meeting high productivity goals by lowering the specific grinding energy and reducing the temperature of the contact zone. The present study investigated the capacity of the jet pressure of a spot nozzle to improve the wear of a CBN wheel when grinding the AISI 690 superalloy. Grinding experiments were conducted with an emulsion-type cooling fluid delivered at pressure ranging from 0.1 to 4 MPa. Results show that the maximum stock removal, reached at 4 MPa, is 5 times the stock removal obtained at 0.1 MPa, while the grinding ratio at 4 MPa is 8 times that at 0.1 MPa, and there is a critical pressure (P c) around 1.5 MPa corresponding to the minimum specific grinding energy. Scanning electron microscopy of the grain tips showed that the wear mechanism shifts from breaking and dislodgment at low jet pressure to micro-fracture resulting in continuous self-sharpening of the abrasive grains. By lubricating at jet pressure close to P c, there is less thermal damage due to plowing and sliding and the resulting lower loading of the abrasive grains favors the micro-fracture of grains and thus a longer wheel life.

  13. Effects of Jet Pressure on the Ground Surface Quality and CBN Wheel Wear in Grinding AISI 690 Nickel-Based Superalloy

    Science.gov (United States)

    Guitouni, Ahmed; Chaieb, Iheb; Rhouma, Amir Ben; Fredj, Nabil Ben

    2016-11-01

    Fluid application in grinding is getting attention as higher stock removal rates, higher surface integrity and longer wheel life are required. It is necessary to define proper conditions of application for meeting high productivity goals by lowering the specific grinding energy and reducing the temperature of the contact zone. The present study investigated the capacity of the jet pressure of a spot nozzle to improve the wear of a CBN wheel when grinding the AISI 690 superalloy. Grinding experiments were conducted with an emulsion-type cooling fluid delivered at pressure ranging from 0.1 to 4 MPa. Results show that the maximum stock removal, reached at 4 MPa, is 5 times the stock removal obtained at 0.1 MPa, while the grinding ratio at 4 MPa is 8 times that at 0.1 MPa, and there is a critical pressure ( P c) around 1.5 MPa corresponding to the minimum specific grinding energy. Scanning electron microscopy of the grain tips showed that the wear mechanism shifts from breaking and dislodgment at low jet pressure to micro-fracture resulting in continuous self-sharpening of the abrasive grains. By lubricating at jet pressure close to P c, there is less thermal damage due to plowing and sliding and the resulting lower loading of the abrasive grains favors the micro-fracture of grains and thus a longer wheel life.

  14. Teeth Grinding: Is Emotional Stability related to Bruxism?

    OpenAIRE

    Sutin, Angelina R; Terracciano, Antonio; Ferrucci, Luigi; Costa, Paul T.

    2010-01-01

    This study examines the association between personality traits and bruxism, the repetitive grinding or clenching of teeth. Community-dwelling participants (N = 470) had a comprehensive oral examination by a dentist and completed a dental history and personality questionnaires. Consistent with the literature on state anxiety and depression as antecedents of bruxism, Neuroticism-related traits were associated with self-reported teeth grinding. These traits were also associated with other oral c...

  15. Performance analysis of magnesium phosphate cement mortar containing grinding dust

    OpenAIRE

    2009-01-01

    Magnesium phosphate cement materials are formed by reacting magnesium oxide with water-soluble phosphates such as monoammonium dihydrogen phosphate (ADP), which solidifies at ambient temperature through the formation of hydrated phases in the material. Cylindrical specimens of magnesium phosphate cement were molded and varying amounts (0 to 30% weight) of grinding dust were added to the ceramic matrices. The influence of the addition of grinding dust on the characteristics of the mortars in t...

  16. A Path Planning Method for Robotic Belt Surface Grinding

    Institute of Scientific and Technical Information of China (English)

    WANG Wei; YUN Chao

    2011-01-01

    The flexible contact and machining with wide strip are two prominent advantages for the robotic belt grinding system,which can be widely used to improve the surface quality and machining efficiency while finishing the workpieces with sculptured surfaces.There lacks research on grinding path planning with the constraint of curvature.With complicated contact between the contact wheel and the workpiece,the grinding paths for robot can be obtained by the theory of contact kinematics.The grinding process must satisfy the universal demands of the belt grinding technologies,and the most important thing is to make the contact wheel conform to the local geometrical features on the contact area.For the local surfaces with small curvature,the curve length between the neighboring cutting locations becomes longer to ensure processing efficiency.Otherwise,for the local areas with large curvature,the curve length becomes shorter to ensure machining accuracy.A series of planes are created to intersect with the target surface to be ground,and the corresponding sectional profile curves are obtained.For each curve,the curve length between the neighboring cutting points is optimized by inserting a cutter location at the local area with large curvatures.A method of generating the grinding paths including curve length spacing optimization is set up.The validity is completely approved by the off-line simulation,and during the grinding experiments with the method,the quality of surface is improved.The path planning method provides a theoretical support for the smooth and accuracy path of robotic surface grinding.

  17. Pyrolysis of a waste from the grinding of scrap tyres

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, A.M. [Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain); Barriocanal, C., E-mail: carmenbr@incar.csic.es [Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain); Alvarez, R. [Instituto Nacional del Carbon, CSIC, Apartado 73, 33080 Oviedo (Spain)

    2012-02-15

    Highlights: Black-Right-Pointing-Pointer The pyrolysis of reinforcing fibres obtained from scrap tyres has been studied. Black-Right-Pointing-Pointer The results have been compared to scrap tyre granules. Black-Right-Pointing-Pointer A higher temperature is needed for the total decomposition of the fibres. Black-Right-Pointing-Pointer More compounds with heteroatoms (O, N) were found in the oil from the fibres. Black-Right-Pointing-Pointer Chars from the fibres exhibit lower BET surface and mesopore volume. - Abstract: The fibres that are used to reinforce tyres can be recovered as a waste in the process of grinding of scrap tyres. In this paper beneficiation through pyrolysis is studied since the fibres are made up of polymers with a small amount of rubber because the latter is difficult to separate. The experiments were performed at three temperatures (400, 550 and 900 Degree-Sign C) in a horizontal oven. The three products - gas, oil and char - obtained from the pyrolysis were investigated. The composition of the gas was analyzed by means of gas chromatography. The oil was studied by gas chromatography and infrared spectroscopy. The char porous structure was determined by N{sub 2} adsorption. In addition, the topography of the chars was studied by means of scanning electron microscopy (SEM). The products resulting from the pyrolysis of the fibres were compared with those obtained from scrap rubber.

  18. Development and Performance Evaluation of Maize Threshing and Grinding Machine

    Directory of Open Access Journals (Sweden)

    Ugwu K. C.

    2016-10-01

    Full Text Available The Maize threshing and grinding machine was designed, fabricated and its performance was evaluated. The machine consists of two compartments which include the threshing and grinding chamber. Threshing chamber is where the maize grain is been separated from the cob, and the cob will be collected through the outlet chute. Therefore, before the maize grain enters into the grinding chamber, blower will separate the grain from the chaff. The separated grain enters the grinding chamber and is being grounded by compressive means through the stationary disc and the grinding plate. A 2 hp electric motor provides drive through belt connections to drive the pulley on threshing chamber and another 2 hp electric motor provide drive for the grinding chamber. The actual test was conducted using three different moisture contents and feed rates. It was observed that the efficiency of the machine was hindered by high moisture content. The results obtained showed that the machine performed well at low moisture content. The efficiency of the machine was 99.01% on the moisture content of 10%. The analysis of variance (ANOVA of the results obtained at 5% percent probability confirmed that the moisture content of the maize was an important parameter that affects the performance of the machine

  19. Electronic tracking of human resource skills and knowledge, just in time training, manageable due diligence

    Energy Technology Data Exchange (ETDEWEB)

    Kolodziej, M.A. [Quick Test International Inc., (Canada). Canadian Technology Human Resource Board; Baker, O. [KeySpan Energy Canada, Calgary, AB (Canada)

    2001-06-01

    KeySpan Energy Canada is in the process of obtaining recognition of various occupational profiles including pipeline operators, inspectors, and field and plant operators from various certifying organizations. The process of allowing individuals to obtain certification is recognized by Canadian Technology Human Resources Board as a step towards national standards for technologists and technicians. Proven competency is a must for workers in todays oil industry in response to increasingly stringent government safety regulations, environmental concerns and high public scrutiny. Quick Test international Inc. has developed a management tool in collaboration with end users at KeySpan Energy Canada. It is an electronic, Internet based competency tool for tracking personal competencies and maintaining continued competency. Response to the tool has been favourable. 2 refs., 4 figs.

  20. [HYGIENIC REGULATION OF THE USE OF ELECTRONIC EDUCATIONAL RESOURCES IN THE MODERN SCHOOL].

    Science.gov (United States)

    Stepanova, M I; Aleksandrova, I E; Sazanyuk, Z I; Voronova, B Z; Lashneva, L P; Shumkova, T V; Berezina, N O

    2015-01-01

    We studied the effect of academic studies with the use a notebook computer and interactive whiteboard on the functional state of an organism of schoolchildren. Using a complex of hygienic and physiological methods of the study we established that regulation of the computer activity of students must take into account not only duration but its intensity either. Design features of a notebook computer were shown both to impede keeping the optimal working posture in primary school children and increase the risk offormation of disorders of vision and musculoskeletal system. There were established the activating influence of the interactive whiteboard on performance activities and favorable dynamics of indices of the functional state of the organism of students under keeping optimal density of the academic study and the duration of its use. There are determined safety regulations of the work of schoolchildren with electronic resources in the educational process.

  1. Medical Image Resource Center--making electronic teaching files from PACS.

    Science.gov (United States)

    Lim, C C Tchoyoson; Yang, Guo Liang; Nowinski, Wieslaw L; Hui, Francis

    2003-12-01

    A picture archive and communications system (PACS) is a rich source of images and data suitable for creating electronic teaching files (ETF). However, the potential for PACS to support nonclinical applications has not been fully realized: at present there is no mechanism for PACS to identify and store teaching files; neither is there a standardized method for sharing such teaching images. The Medical Image Resource Center (MIRC) is a new central image repository that defines standards for data exchange among different centers. We developed an ETF server that retrieves digital imaging and communication in medicine (DICOM) images from PACS, and enables users to create teaching files that conform to the new MIRC schema. We test-populated our ETF server with illustrative images from the clinical case load of the National Neuroscience Institute, Singapore. Together, PACS and MIRC have the potential to benefit radiology teaching and research.

  2. Electronic Human Resource Management (e-HRM of Hotel Business in Phuket

    Directory of Open Access Journals (Sweden)

    Kitimaporn Choochote

    2015-04-01

    Full Text Available This research aims to study the pattern of the electronic human resources management (e-HRM of the hotel business in Phuket. The study is conducted with the implementation of field data and in-depth interview of hotels’ HR managers. In consequence, the study reveals that the hotel business has applied the use of the e-HRM varying in job recruitment (15 percent, employee engagement (55 percent, organizational file structure (10 percent, idea and creativity exchanges (38 percent and assessment system (6 percent. However, considered as 100 percent, the hotel business has not prepared to apply the use of the e-HRM in salary system, learning and training program, welfare allocation and career development.

  3. Using mobile electronic devices to deliver educational resources in developing countries.

    Science.gov (United States)

    Mazal, Jonathan Robert; Ludwig, Rebecca

    2015-01-01

    Developing countries have far fewer trained radiography professionals than developed countries, which exacerbates the limited access to imaging services. The lack of trained radiographers reflects, in part, limited availability of radiographer-specific educational resources. Historically, organizations that provided such resources in the developing world faced challenges related to the limited stock of current materials as well as expenses associated with shipping and delivery. Four mobile electronic devices (MEDs) were loaded with educational content (e-books, PDFs, and digital applications) spanning major radiography topics. The MEDs were distributed to 4 imaging departments in Ghana, India, Nepal, and Nigeria based on evidence of need for radiography-specific resources, as revealed by survey responses. A cost comparison of postal delivery vs digital delivery of educational content was performed. The effectiveness of delivering additional content via Wi-Fi transmission also was evaluated. Feedback was solicited on users' experience with the MEDs as a delivery tool for educational content. An initial average per e-book expense of $30.05, which included the cost of the device, was calculated for the MED delivery method compared with $15.56 for postal delivery of printed materials. The cost of the MED delivery method was reduced to an average of $10.05 for subsequent e-book deliveries. Additional content was successfully delivered via Wi-Fi transmission to all recipients during the 3-month follow-up period. Overall user feedback on the experience was positive, and ideas for enhancing the MED-based method were identified. Using MEDs to deliver radiography-specific educational content appears to be more cost effective than postal delivery of printed materials on a long-term basis. MEDs are more efficient for providing updates to educational materials. Customization of content to department needs, and using projector devices could enhance the usefulness of MEDs for

  4. Plastics disassembly versus bulk recycling: engineering design for end-of-life electronics resource recovery.

    Science.gov (United States)

    Rios, Pedro; Stuart, Julie Ann; Grant, Ed

    2003-12-01

    Annual plastic flows through the business and consumer electronics manufacturing supply chain include nearly 3 billion lb of high-value engineering plastics derived from petroleum. The recovery of resource value from this stream presents critical challenges in areas of materials identification and recycling process design that demand new green engineering technologies applied together with life cycle assessment and ecological supply chain analysis to create viable plastics-to-plastics supply cycles. The sustainable recovery of potentially high-value engineering plastics streams requires that recyclers either avoid mixing plastic parts or purify later by separating smaller plastic pieces created in volume reduction (shredding) steps. Identification and separation constitute significant barriers in the plastics-to-plastics recycling value proposition. In the present work, we develop a model that accepts randomly arriving electronic products to study scenarios by which a recycler might identify and separate high-value engineering plastics as well as metals. Using discrete eventsimulation,we compare current mixed plastics recovery with spectrochemical plastic resin identification and subsequent sorting. Our results show that limited disassembly with whole-part identification can produce substantial yields in separated streams of recovered engineering thermoplastics. We find that disassembly with identification does not constitute a bottleneck, but rather, with relatively few workers, can be configured to pull the process and thus decrease maximum staging space requirements.

  5. SAGES: a suite of freely-available software tools for electronic disease surveillance in resource-limited settings.

    Directory of Open Access Journals (Sweden)

    Sheri L Lewis

    Full Text Available Public health surveillance is undergoing a revolution driven by advances in the field of information technology. Many countries have experienced vast improvements in the collection, ingestion, analysis, visualization, and dissemination of public health data. Resource-limited countries have lagged behind due to challenges in information technology infrastructure, public health resources, and the costs of proprietary software. The Suite for Automated Global Electronic bioSurveillance (SAGES is a collection of modular, flexible, freely-available software tools for electronic disease surveillance in resource-limited settings. One or more SAGES tools may be used in concert with existing surveillance applications or the SAGES tools may be used en masse for an end-to-end biosurveillance capability. This flexibility allows for the development of an inexpensive, customized, and sustainable disease surveillance system. The ability to rapidly assess anomalous disease activity may lead to more efficient use of limited resources and better compliance with World Health Organization International Health Regulations.

  6. Quenching simulation of steel grinding balls

    Directory of Open Access Journals (Sweden)

    Zapata-Hernández, Oscar

    2015-09-01

    Full Text Available The phase transformations of high carbon steel during quenching and equalizing were modelled using commercial computer packages based on the finite element method and the kinetic transformation of steel. The model was used to predict the temperature and microstructural changes taking place within balls of two different sizes that are used for grinding mineral ores. A good correlation between the temperatures measured by inserted thermocouples and those predicted by the model was obtained after modifying the thermal conductivity of the steel within the temperature domain at which mixed phases are present. The phase transformations predicted were confirmed by metallographic analyses.Las transformaciones de fase en aceros de alto carbono durante su temple y un posterior periodo de estabilización fueron modelizadas por medio del uso de paquetes computacionales basados en el método del elemento finito y de la transformación cinética de los aceros. El modelo se usó para predecir los cambios de temperatura y microestructura que se presentan en bolas de dos diferentes tamaños empleadas en estaciones de molienda de minerales. Se encontró una buena correlación entre las temperaturas medidas mediante la inserción de termopares y aquellas predichas por el modelo una vez que se modificó la conductividad térmica del acero en el intervalo mixto de fases. La predicción de las transformaciones de fase se confirmó a través del análisis metalográfico.

  7. Performance of Cooled Cone Grinding Machine in Cocoa Cake Processing

    Directory of Open Access Journals (Sweden)

    Hendy Firmanto

    2015-08-01

    Full Text Available The process of cocoa paste pressing has a function to separate the fatty component of cocoa from its cake. Cocoa paste is further processed into cocoa powder using grinding machine for cocoa cake. The cooled cone type of cocoa grinding machine is used to solve the problem of plug in the maschine caused by melting of fat in cocoa cake due to hot effect as a result of friction in the grinding machine. Grinding machine of cocoa has conical form of cylinder for grinding and stator wall wrapped by source of cold and closed with jacket wool. Research was conducted at Kaliwining Experimental Garden of Indonesian Coffee and Cocoa Research Institute (ICCRI using cocoa cake containing 26.75% originated from Forastero type of cocoa seed. The capacity and recovery of the machine was influenced by space between rotor cylinder and stator wall. Grinding machine operated at cooling temperature of 25.5oC and space between rotor – stator 0.9 cm and the capacity of 187.5 kg/hour with recovery of 200 mesh cocoa powder as much as 24%. The maximum  power of machine required  was 2.5 kW with efficiency of  energy transfer of 97%. Results of proximate analysis showed that there was no change of protein content, but protein and carbohydrate content increased after processing, i.e. from 5.70% and 59.82% into 5.80% and 61.89% respectively.Key words : cocoa cake, cooling, grinding, cocoa powder 

  8. The effect of cryogenic grinding and hammer milling on the flavour quality of ground pepper (Piper nigrum L.).

    Science.gov (United States)

    Liu, Hong; Zeng, Fankui; Wang, Qinghuang; Ou, Shiyi; Tan, Lehe; Gu, Fenglin

    2013-12-15

    In this study, we compared the effects of cryogenic grinding and hammer milling on the flavour attributes of black, white, and green pepper. The flavour attributes were analysed using headspace solid-phase micro-extraction (HS-SPME) and gas chromatography-mass spectrometry (GC/MS), sensory evaluation and electronic nose (e-nose) analysis. Cryogenic grinding resulted in minimal damage to the colour, flavour, and sensory attributes of the spices. Cryogenic grinding was also better than hammer milling at preserving the main potent aroma constituents, but the concentrations of the main aroma constituents were dramatically reduced after storing the samples at 4 °C for 6 months. Pattern matching performed by the e-nose further supported our sensory and instrumental findings. Overall, cryogenic grinding was superior to hammer milling for preserving the sensory properties and flavour attributes of pepper without significantly affecting its quality. However, we found that the flavour quality of ground pepper was reduced during storage. Copyright © 2013 Elsevier Ltd. All rights reserved.

  9. Analysis of the influence of infeed rate and cutting fluid on cylindrical grinding processes using a conventional wheel

    Directory of Open Access Journals (Sweden)

    Bianchi Eduardo Carlos

    2004-01-01

    Full Text Available New worldwide trends such as globalization have rendered grinding processes increasingly important for industry, making it essential to perform in-depth studies of variations in grinding process parameters in the pursuit of greater cost effectiveness. This paper presents a comparative analysis of three different infeed rates, using a conventional grinding wheel on quenched and tempered D2 steel workpieces. Higher infeed rates are known to be correlated with shorter grinding times, rendering the process more economically attractive. Two different coolant fluids, 5% emulsion and pure oil, were used. The tests were carried out using the smallest possible amount of coolant and an optimized 5 mm diameter nozzle. The parameters analyzed were tangential force, specific energy, acoustic emission, roundness error and surface roughness. The surfaces of the workpieces were also examined by scanning electron microscopy (SEM. The results revealed that increased infeed rates could reduce processing times without compromising the quality of the workpiece profile, thereby reducing the cost of the process. The best cutting fluid, albeit more harmful to human health and less environmentally friendly, was found to be pure oil.

  10. Effect of superfine grinding on the physico-chemical, morphological and thermogravimetric properties of Lentinus edodes mushroom powders.

    Science.gov (United States)

    Ming, Jian; Chen, Long; Hong, Hui; Li, Jinlong

    2015-09-01

    Lentinus edodes is an edible mushroom commonly known as shiitake, which is the second most produced and consumed edible mushroom in the world and is an important nutrient source in the human diet. To fully use L. edodes, the mushrooms are occasionally ground into powder as a flavourful and functional food additive. This study produces powders from the cap and stipe of Lentinus edodes mushrooms through superfine grinding. These powders are composed of sub-micron range particles with various size distributions. The superfine grinding process is then compared with shear pulverisation to determine the different effects on both the cap and stipe powders in terms of particle size and physico-chemical, morphological and thermogravimetric properties. When average particle size was reduced to 0.54 and 0.46 µm, respectively, the moisture and protein content, angles of repose and slide, and water holding capacity of the powders decreased to varied extents. However, soluble dietary fibre, water solubility index, and swelling capacity increased. Scanning electron microscope images suggested that the superfine grinding process effectively changed the original surface structure of the L. edodes powders. The curves of thermogravimetric analysis and those of the derivatives of thermogravimetry indicated that superfine grinding can improve the thermostability of L. edodes powders. Furthermore, superfinely ground L. edodes powders may be used as pharmaceutical or food additives in various fields. The present study suggests that superfinely ground L. edodes powders may be applied in various fields as pharmaceutical or food additives. © 2014 Society of Chemical Industry.

  11. Research on Stability Prediction of the Crankshaft CNC Tangential Point Tracing Grinding

    Directory of Open Access Journals (Sweden)

    Zhuoda Jiang

    2015-01-01

    Full Text Available As the key part of internal combustion engines, crankshaft with high efficiency and accuracy processing has always been the target of the engine manufacturer’s pursuit. Grinding is used to obtain the ultimate dimensional accuracy and surface finish in the crankshaft machining. Grinding of the main journals and the pin journals can be accomplished in a single clamping operation by CNC Tangential Point Tracing grinding technology. However, the chatter in the grinding process is harmful to the precision and surface quality. In this paper, stability lobe diagram is developed to predict the grinding chatter. First the dynamic model of Tangential Point Tracing grinding system is established. Then the limit formula of the critical grinding depth is calculated and the stability lobe diagram of the grinding system is presented. Finally, the validation experiments are carried out on the crankshaft grinding machine and the results are consistent with the calculation.

  12. Geometrical principium of fewer-axis grinding for large complex optical mirrors

    Institute of Scientific and Technical Information of China (English)

    JIANG; ZhenHua; YIN; YueHong

    2013-01-01

    Ultraprecision grinding is an important approach to efficiently fabricate large complex optical mirrors, and five-axis grinding method is commonly used for ultraprecision grinding. However, this method can hardly meet the high stiffness requirement for grinding large mirror, especially with a diameter over 2 m. Meanwhile, the use of fewer-axis grinding solves this problem, as it reduces the number of the grinder’s axes to improve the rigidity of the system and minimize deformation for hard and brittle materials. But its characteristic of unfixed grinding point which changes with workpiece surface curvature increases geometric complexity and requires a higher geometric shape accuracy of grinding wheel. This paper parameterizes grinding wheel’s geometric shape, reveals the relationship between fewer-axis and five-axis grinding methods from the point of view of the differential geometry, and establishes virtual-axis equivalence principium of feweraxis grinding. A quantitative method to determine grinding wheel’s geometric parameters and its shaft inclination angle is proposed based on the requirements of geometric properties of optical mirror, grinder features and grinding process. Moreover, according to the properties of Gauss curvature of curved surface, the wear law of the toric grinding wheel is found and the surface geometric error distribution due to wear is achieved for fewer-axis grinding. The correctness of the principium and method above are verified through simulations.

  13. STUDIES ON CONTINUOUS GRINDING PROCESS FOR DRIED WATER CHESTNUT KERNEL

    Directory of Open Access Journals (Sweden)

    S.K. GARG

    2010-06-01

    Full Text Available Grinding is a unit operation to break big solid material into smaller pieces. As far as process of grinding is concerned, power consumption, specific energy consumption and particle size distribution and mill capacity are main considerations from engineering point of view. The experiments were conducted to study the effect of speed of mill, sieve size, feed rate and time of grinding on power consumption and average particle diameter of water chestnut in continuous grinding process. Power consumption was measured for a constant feed rate of 1 and 2 kg/h at different speed of the mill varied from 800 to 1200 rpm for the sieve openings of 0.5 mm, 1.0 mm and 2.0 mm. For all the sieve sizes and feed rates, it was observed that as the speed of the mill increases, there is an increase in power consumption and found significantly low for higher sieve size and lower feed rate. The size distribution of the water chestnut kernel for different speeds and sieve sizes at constant feed rate were obtained by sieve analysis. The milling speed has no significant effect on particle size distribution of ground product and mass fraction was minimum at lower feed rate and higher sieve size. Harris model was found best suitable to describe the size distribution in continuous grinding process. Fineness modulus decreases with increase of milling speed for experimental sieve size and feed rate.

  14. Low-Rank Coal Grinding Performance Versus Power Plant Performance

    Energy Technology Data Exchange (ETDEWEB)

    Rajive Ganguli; Sukumar Bandopadhyay

    2008-12-31

    The intent of this project was to demonstrate that Alaskan low-rank coal, which is high in volatile content, need not be ground as fine as bituminous coal (typically low in volatile content) for optimum combustion in power plants. The grind or particle size distribution (PSD), which is quantified by percentage of pulverized coal passing 74 microns (200 mesh), affects the pulverizer throughput in power plants. The finer the grind, the lower the throughput. For a power plant to maintain combustion levels, throughput needs to be high. The problem of particle size is compounded for Alaskan coal since it has a low Hardgrove grindability index (HGI); that is, it is difficult to grind. If the thesis of this project is demonstrated, then Alaskan coal need not be ground to the industry standard, thereby alleviating somewhat the low HGI issue (and, hopefully, furthering the salability of Alaskan coal). This project studied the relationship between PSD and power plant efficiency, emissions, and mill power consumption for low-rank high-volatile-content Alaskan coal. The emissions studied were CO, CO{sub 2}, NO{sub x}, SO{sub 2}, and Hg (only two tests). The tested PSD range was 42 to 81 percent passing 76 microns. Within the tested range, there was very little correlation between PSD and power plant efficiency, CO, NO{sub x}, and SO{sub 2}. Hg emissions were very low and, therefore, did not allow comparison between grind sizes. Mill power consumption was lower for coarser grinds.

  15. Ductile streaks in precision grinding of hard and brittle materials

    Indian Academy of Sciences (India)

    V C Venkatesh; S Izman; S Sharif; T T Mon; M Konneh

    2003-10-01

    Ductile streaks produced during diamond grinding of hard and brittle materials have aided the subsequent process of polishing. Two novel techniques were used to study the formation of ductile mode streaks during diamond grinding (primary process) of germanium, silicon, and glass. In the first technique, aspheric surfaces were generated on Ge and Si at conventional speeds (5000 rpm). In the second technique, diamond grinding of plano surfaces on glass and Si surfaces using high speed (100,000 rpm) was carried out. Form accuracy, surface finish and ductile mode grinding streaks are discussed in this paper. It was found that resinoid diamond wheels gave more ductile streaks than metal-bonded wheels but better form accuracy was obtained with the latter. Ductile streaks were obtained more easily with pyrex rather than with BK 7 glass thus necessitating very little time for polishing. Ductile streaks appeared in abundance on germanium rather than silicon. Both the novel grinding techniques were used on CNC machining centres.

  16. Impact of Electronic Resources and Usage in Academic Libraries in Ghana: Evidence from Koforidua Polytechnic & All Nations University College, Ghana

    Science.gov (United States)

    Akussah, Maxwell; Asante, Edward; Adu-Sarkodee, Rosemary

    2015-01-01

    The study investigates the relationship between impact of electronic resources and its usage in academic libraries in Ghana: evidence from Koforidua Polytechnic & All Nations University College, Ghana. The study was a quantitative approach using questionnaire to gather data and information. A valid response rate of 58.5% was assumed. SPSS…

  17. Utilization of Electronic Information Resources by Undergraduate Students of University of Ibadan: A Case Study of Social Sciences and Education

    Science.gov (United States)

    Owolabi, Sola; Idowu, Oluwafemi A.; Okocha, Foluke; Ogundare, Atinuke Omotayo

    2016-01-01

    The study evaluated utilization of electronic information resources by undergraduates in the Faculties of Education and the Social Sciences in University of Ibadan. The study adopted a descriptive survey design with a study population of 1872 undergraduates in the Faculties of Education and the Social Sciences in University of Ibadan, from which a…

  18. Shape-Grinding by Direct Position/Force Control

    Science.gov (United States)

    Chen, Guanghua; Xu, Weiwei; Minami, Mamoru

    Based on the analysis of the interaction between a manipulator's hand and a working object, a model representing the constrained dynamics of the robot is first discussed. The constrained forces are expressed by an algebraic function of states, input generalized forces, and the constraint condition, and then a direct position/force controller without force sensor is proposed based on the algebraic relation. To give a grinding system the ability to adapt to any object shape being changed by the grinding, we add a function estimating the constraint condition in real time for the adaptive position/force control. Evaluations through simulations, by fitting the changing constraint surface with spline functions, indicate that reliable position/force control and shape-grinding can be achieved by the proposed controller.

  19. Grinding process within vertical roller mills: experiment and simulation

    Institute of Scientific and Technical Information of China (English)

    WANG Jian-huai; CHEN Qing-ru; KUANG Ya-li; LYNCH A J; ZHUO Jin-wu

    2009-01-01

    Based on screening analysis, laser size analysis, grindability and rigidity tests of samples collected on line from a cement and a power plant, a simulation of the grinding process in vertical roller mills was carried out. The simulation calculation used a breakage function, B. The results indicate that the breakage function, B, and the selection function, S, in the form of a matrix, can be used to express the probability of the material breaking during the grinding process. This allows the size distribution of the product to be numerically estimated. The simulation results also show that the simulated size distribution curves fit the actual ex-perimental product curves quite well. The model provides a good starting point for simulation of the grinding process. Further re-search is needed to determine the proper breakage function and the matrix value of the selection function.

  20. Design and experimental study of a micro-groove grinding wheel with spray cooling effect

    Directory of Open Access Journals (Sweden)

    Shi Chaofeng

    2014-04-01

    Full Text Available The effectiveness of grinding fluid supply has a crucial impact on grinding quality and efficiency in high speed grinding. In order to improve the cooling and lubrication, through in-depth research of self-inhaling internal cooling method and intermittent grinding mechanism, a new spray cooling method used in high speed grinding is proposed. By referring to the structure of bowl-shaped dispersion disk, the grinding wheel matrix with atomization ability is designed; through studying heat transfer of droplet collision and the influence of micro-groove on the boiling heat transfer, grinding segment with micro-groove is designed to enhance the heat flux of coolant and achieve maximum heat transfer between droplets and grinding contact zone. High-speed grinding experiments on GH4169 with the developed grinding wheel are carried out. The results show that with the micro-groove grinding wheel just 5.4% of pump outlet flow rate and 0.5% of spindle energy is needed to reduce the grinding temperature to 200 °C, which means the developed grinding wheel makes cooling high efficient and low energy consuming.

  1. High-speed, low-damage grinding of advanced ceramics Phase 1. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kovach, J.A. [Eaton Corp., Willoughby Hills, OH (United States). Mfg. Technologies Center; Malkin, S. [Univ. of Massachusetts (United States)

    1995-03-01

    In manufacture of structural ceramic components, grinding costs can comprise up to 80% of the entire manufacturing cost. Most of these costs arise from the conventional multi-step grinding process with numerous grinding wheels and additional capital equipment, perishable dressing tools, and labor. In an attempt to reduce structural ceramic grinding costs, a feasibility investigation was undertaken to develop a single step, roughing-finishing process suitable for producing high-quality silicon nitride ceramic parts at high material removal rates at lower cost than traditional, multi-stage grinding. This feasibility study employed combined use of laboratory grinding tests, mathematical grinding models, and characterization of resultant material surface condition. More specifically, this Phase 1 final report provides a technical overview of High-Speed, Low-Damage (HSLD) ceramic grinding and the conditions necessary to achieve the small grain depths of cut necessary for low damage grinding while operating at relatively high material removal rates. Particular issues addressed include determining effects of wheel speed and material removal rate on resulting mode of material removal (ductile or brittle fracture), limiting grinding forces, calculation of approximate grinding zone temperatures developed during HSLD grinding, and developing the experimental systems necessary for determining HSLD grinding energy partition relationships. In addition, practical considerations for production utilization of the HSLD process are also discussed.

  2. Characterization of the mechanical properties and structural integrity of T-welded connections repaired by grinding and wet welding

    Energy Technology Data Exchange (ETDEWEB)

    Terán, G., E-mail: gteran@imp.mx [Instituto Mexicano del Petróleo, Eje central Lázaro Cárdenas 152, Col. San Bartolo Atepehuacan, México D.F. CP 07730, México (Mexico); Cuamatzi-Meléndez, R., E-mail: rcuamatzi@imp.mx [Instituto Mexicano del Petróleo, Eje central Lázaro Cárdenas 152, Col. San Bartolo Atepehuacan, México D.F. CP 07730, México (Mexico); Albiter, A., E-mail: aalbiter@imp.mx [Instituto Mexicano del Petróleo, Eje central Lázaro Cárdenas 152, Col. San Bartolo Atepehuacan, México D.F. CP 07730, México (Mexico); Maldonado, C., E-mail: cmzepeda@umich.mx [Instituto de Investigaciones Metalúrgicas, UMSNH, PO Box 52-B, 58000, México (Mexico); Bracarense, A.Q., E-mail: bracarense@ufmg.br [UFMG Departamento de Engeharia Mecánica Belo Horizonte, MG (Brazil)

    2014-04-01

    This paper presents an experimental methodology to characterize the structural integrity and mechanical properties of repaired T-welded connections using in fixed offshore structures. Grinding is employed to remove localized damage like cracking and corrosion and subsequent wet welding can be used to fill the grinded material. But it is important to define the grinding depth and profile in order to maintain structural integrity during the repair. Therefore, in this work different grinding depths were performed, for damage material removal, at the weld toe of the T-welded connections. The grinding was filled by wet welding in a hyperbaric chamber, simulating three different water depths: 50 m, 70 m and 100 m. The electrodes were coated with vinilic varnish, which is cheap and easy to apply. The characterization of the mechanical properties of the T-welded connections was done with standard tensile, hardness and Charpy tests; microstructure and porosity analysis were also performed. The samples were obtained from the welded connections in regions of the wet weld beads. The test results were compared with the mechanical properties of the T-welded connections welded in air conditions performed by other authors. The results showed that the wet welding technique performed in this work produced good mechanical properties of the repaired T-welded connection. The mechanical properties, measured in wet conditions, for 6 mm grinding depth, were similar for the 3 different water depths measured in air conditions. But for 10 mm grinding depth, the values of the mechanical properties measured in wet conditions were quite lower than that for air conditions for the 3 water depths. However a porosity analysis, performed with a Scanning Electronic Microscopy (SEM), showed that the level of porosity in the resulted wet weld beads is in the range of that published in the literature and some samples revealed lower level of porosity. The main resulting microstructure was polygonal

  3. Robotic Instrument for Grinding Rocks Into Thin Sections (GRITS)

    Science.gov (United States)

    Paulsen, Gale; Zacny, Kris; Dreyer, Christopher B.; Szucs, Attila; Szczesiak, Matt; Santoro, Chris; Craft, Jack; Hedlund, Magnus; Skok, John

    2013-06-01

    We have developed a rock grinding and polishing mechanism for in situ planetary exploration based on abrasive disks, called Grinding Rocks Into Thin Sections (GRITS). Performance characteristics and design considerations of GRITS are presented. GRITS was developed as part of a broader effort to develop an in situ automated rock thin section (ISARTS) instrument. The objective of IS-ARTS was to develop an instrument capable of producing petrographic rock thin sections on a planetary science spacecraft. GRITS may also be useful to other planetary science missions with in situ instruments in which rock surface preparation are necessary.

  4. Performance analysis of magnesium phosphate cement mortar containing grinding dust

    Directory of Open Access Journals (Sweden)

    Daniel Véras Ribeiro

    2009-03-01

    Full Text Available Magnesium phosphate cement materials are formed by reacting magnesium oxide with water-soluble phosphates such as monoammonium dihydrogen phosphate (ADP, which solidifies at ambient temperature through the formation of hydrated phases in the material. Cylindrical specimens of magnesium phosphate cement were molded and varying amounts (0 to 30% weight of grinding dust were added to the ceramic matrices. The influence of the addition of grinding dust on the characteristics of the mortars in terms of microstructure (SEM, mechanical strength and capillary water absorption was verified. The results obtained proved very satisfactory for the use of this waste as an additive in magnesium phosphate mortars.

  5. INVESTIGATION OF SURFACE TEMPERATURE IN HIGH-EFFICIENCY DEEP GRINDING

    Institute of Scientific and Technical Information of China (English)

    Zhao Henghua; Cai Guangqi; Jin Tan

    2005-01-01

    A new thermal model with triangular heat flux distribution is given in high-efficiency deep grinding. The mathematical expressions are driven to calculate the surface temperature. The transient behavior of the maximum temperature on contact area is investigated in different grinding conditions with a J-type thermocouple. The maximum contact temperatures measured in different conditions are found to be between 1 000 ℃ and 1 500 ℃ in burn-out conditions. The experiment results show good agreement with the new thermal model.

  6. Graphic presentation of information of acoustic monitoring of stream grinding process

    Directory of Open Access Journals (Sweden)

    N.S. Pryadko

    2012-04-01

    Full Text Available The theoretical and experimental mechanisms of thin grinding the loose materials are analyzed. The relation of the density function of acoustic signal amplitudes of grinding process to the degree of loading the jets by material is established.

  7. Effect of disintegration wave grinding on fractional protein and amino acid composition of chickpea

    Directory of Open Access Journals (Sweden)

    G. O. Magomedov

    2013-01-01

    Full Text Available The study of fractional changes and amino acid composition of proteins in the application of chickpea disintegration wave grinding. Comparative analysis of six varieties of chickpea before and after grinding.

  8. Effects of the grinding process on the preparation and qualities of CWS

    Institute of Scientific and Technical Information of China (English)

    Yuliang Zhang; Guoguang Wu; Xianliang Meng; Zengjie Yun; Frank Shi; Yaqun He; Xiaoqiang Luo

    2011-01-01

    Two different grinding processes were examined to determine the effect grinding has on the quality of a CWS.A series of slurries was prepared from Australian (Au) and Chinese (YZ) coals.Both types of coal were ground by a Chinese (CUMT) and an Australian (JK) grinding process.The performance tests of the prepared CWS showed that fluidity of all slurries was acceptable.The concentration of the CWS from YZ coal ground by the CUMT grinding process was higher than when the JK grinding process was used.The highest concentration was 70.14% in this case.The concentration of the CWS prepared from Au coal by the JK grinding process was higher than when the CUMT grinding process was used.The highest concentration in this case was 70.97%.These differences are caused by the particle size distribution developed during the different grinding processes.

  9. THERMAL AND PHYSICAL FEATURES OF MAGNETIC AND ELECTRIC GRINDING PROCESS OF GAS AND THERMAL PROTECTIVE COATINGS

    OpenAIRE

    N. V. Spiridonov; I. O. Sokorov; M. V. Niaroda

    2008-01-01

    The paper reveals thermal zones of magnetic and electric grinding process. The influence of electric and physical parameters of magnetic and electric grinding on temperature in the zone of gas and thermal protective coatings has been established in the paper.

  10. A mathematical model for surface roughness of fluidic channels produced by grinding aided electrochemical discharge machining (G-ECDM)

    National Research Council Canada - National Science Library

    V G Ladeesh; R Manu

    2017-01-01

    Grinding aided electrochemical discharge machining is a hybrid technique, which combines the grinding action of an abrasive tool and thermal effects of electrochemical discharges to remove material...

  11. Effect of Grinding Process Parameters on Surface Area Roughness of Glass fibre Reinforced Composite Laminate under Dry and Coolant Environment

    Directory of Open Access Journals (Sweden)

    P. Chockalingam

    2016-04-01

    Full Text Available This paper presents a comparative study on dry and wet grinding of chopped strand mat glass fibre reinforced polymer laminates using an alumina wheel. Investigations were performed to study the impact of the grinding parameters, namely feed, speed, and depth of cut on grinding force ratio and surface area roughness. Effective grinding parameters were sought in this study to maximize grinding force ratio and minimize surface area roughness. Test results show that coolant helped to decrease surface area roughness, but inevitably reduced the grinding force ratio in some cases. These findings lead to economic machining solution for optimum grinding conditions in grinding composite laminates.

  12. Human resource requirements for quality-assured electronic data capture of the tuberculosis case register

    Directory of Open Access Journals (Sweden)

    Hoa Nguyen B

    2012-01-01

    Full Text Available Abstract Background The tuberculosis case register is the data source for the reports submitted by basic management units to the national tuberculosis program. Our objective was to measure the data entry time required to complete and double-enter one record, and to estimate the time for the correction of errors in the captured information from tuberculosis case registers in Cambodia and Viet Nam. This should assist in quantifying the additional requirements in human resources for national programs moving towards electronic recording and reporting. Methods Data from a representative sample of tuberculosis case registers from Cambodia and Viet Nam were double-entered and discordances resolved by rechecking the original case register. Computer-generated data entry time recorded the time elapsed between opening of a new record and saving it to disk. Results The dataset comprised 22,732 double-entered records of 11,366 patients (37.1% from Cambodia and 62.9% from Viet Nam. The mean data entry times per record were 97.5 (95% CI: 96.2-98.8 and 66.2 (95% CI: 59.5-73.0 seconds with medians of 90 and 31 s respectively in Cambodia and in Viet Nam. The percentage of records with an error was 6.0% and 39.0% respectively in Cambodia and Viet Nam. Data entry time was inversely associated with error frequency. We estimate that approximately 118-person-hours were required to produce 1,000 validated records. Conclusions This study quantifies differences between two countries for data entry time for the tuberculosis case register and frequencies of data entry errors and suggests that higher data entry speed is partially offset by requiring revisiting more records for corrections.

  13. Use and Cost of Electronic Resources in Central Library of Ferdowsi University Based on E-metrics

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Davarpanah

    2012-07-01

    Full Text Available The purpose of this study was to investigate the usage of electronic journals in Ferdowsi University, Iran based on e-metrics. The paper also aimed to emphasize the analysis of cost-benefit and the correlation between the journal impact factors and the usage data. In this study experiences of Ferdowsi University library on licensing and usage of electronic resources was evaluated by providing a cost-benefit analysis based on the cost and usage statistics of electronic resources. Vendor-provided data were also compared with local usage data. The usage data were collected by tracking web-based access locally, and by collecting vender-provided usage data. The data sources were one-year of vendor-supplied e-resource usage data such as Ebsco, Elsevier, Proquest, Emerald, Oxford and Springer and local usage data collected from the Ferdowsi university web server. The study found that actual usage values differ for vendor-provided data and local usage data. Elsevier has got the highest usage degree in searches, sessions and downloads. Statistics also showed that a small number of journals satisfy significant amount of use while the majority of journals were used less frequent and some were never used at all. The users preferred the PDF rather than HTML format. The data in subject profile suggested that the provided e-resources were best suited to certain subjects. There was no correlation between IF and electronic journal use. Monitoring the usage of e-resources gained increasing importance for acquisition policy and budget decisions. The article provided information about local metrics for the six surveyed vendors/publishers, e.g. usage trends, requests per package, cost per use as related to the scientific specialty of the university.

  14. Investigation of glycerol polymerization in the clinker grinding process

    NARCIS (Netherlands)

    Parvulescu, A.N.; Rossi, M.; Della Pina, C.; Ciriminna, R.; Pagliaro, M.

    2011-01-01

    Concrete production is a large scale process that involves high energy consumption. In order to increase the sustainability of this process, the reduction of energy input is necessary. Bio-glycerol was demonstrated to be a highly efficient renewable-based additive in the grinding process for concret

  15. Contact and Non-contact Measurements of Grinding Pins

    Directory of Open Access Journals (Sweden)

    Magdziak Marek

    2015-01-01

    Full Text Available The paper presents the results of contact and non-contact measurements of external profiles of selected grinding pins. The measurements were conducted in order to choose the appropriate measuring technique in the case of the considered measurement task. In the case of contact measurements the coordinate measuring machine ACCURA II was applied. The used coordinate measuring machine was equipped with the contact scanning probe VAST XT and the Calypso inspection software. Contact coordinate measurements were performed by using of different measurement strategies. The applied strategies included different scanning velocities and distances between measured points. Non-contact measurements were conducted by means of the tool presetter produced by the Mahr company. On the basis of gained results the guidelines concerning measurements of grinding pins were formulated. The measurements of analyzed grinding pins performed by means of the non-contact measuring system are characterized by higher reproducibility than the contact measurements. The low reproducibility of contact measurements may be connected with the inaccuracy of the selected coordinate measuring machine and the measuring probe, the measurement parameters and environmental conditions in the laboratory where the coordinate measuring machine is located. Moreover, the paper presents the possible application of results of conducted investigations. The results of non-contact measurements can be used in the simulation studies of grinding processes. The simulations may reduce the costs of machining processes.

  16. GRINDING OF SHAPED TOOLS ON CNC TOOL GRINDER

    Directory of Open Access Journals (Sweden)

    Ján Kráľ

    2013-03-01

    Full Text Available Worm gears are special gears consisting of a worm wheel and a worm. Worm gears can be produced in different ways, depending on the size of the transmission, the number of courses, the pitch angle of worm profile, the number of units produced, the purpose of application, etc. As cylindrical worm gears we consider the cylindrical worms with globoid gears, globoid worm with globoid worm gear and globoid worm with cylindrical worm gearing. This paper deals with the evolvent worm whose curve of the tooth side in the front plane is evolvent. The production of worm with an optimal profile for optimal meshing conditions is an increasingly frequent focus of worm gear manufacturers. The problem of designing the tool cutting edge can be divided into several steps. This article deals with the problems of optimum design of a tool shape for the production of worms; and the problems of calculating the coordinates of the transition cutting edge shape, and thus the path of grinding wheel for sharpening the tool cutting edge shape are solved. By grinding tool of grinding machine we can complete the worm shape and also sharpen the cutting edges of tools for production of worm surface. The problems of calculation of the coordinates are solved with regard to the functioning of the KON 250 CNC grinding machine logic.

  17. Cobalt exposure in a carbide tip grinding process.

    Science.gov (United States)

    Stebbins, A I; Horstman, S W; Daniell, W E; Atallah, R

    1992-03-01

    Reports relating hard metal disease or nonspecific respiratory symptoms to tungsten or cobalt exposure have been published in the past 20 yr. This report discusses a work site investigation of a small company, employing approximately 50 workers, producing carbide tip saw blades for the woodworking industry. Cobalt exposure was characterized by ambient air monitoring (area and personnel), particle size determination, and biological monitoring. Area sampling for cadmium, cobalt, and tungsten indicated low ambient air levels in all manufacturing areas except the grinding department, which had cobalt air levels approaching the threshold limit value of 0.05 mg/m3. Area airborne cobalt exposure levels measured over six shifts in the grinding department ranged from 0.017 to 0.12 mg/m3 for the total collection method and 0.002 to 0.028 mg/m3 for the method collecting respirable particles. Cobalt content in the total and respirable fractions was similar. Urine monitoring indicated production workers have elevated cobalt levels, and the grinders' levels were higher than other production workers. The grinding coolant was found to have elevated cobalt concentrations. A survey of coolants from nine carbide grinding shops indicated the elevated cobalt concentrations may be common.

  18. The Graduate Grind: A Critical Look at Graduate Education

    Directory of Open Access Journals (Sweden)

    Michelle K. McGinn

    2010-05-01

    Full Text Available Abandonment, abuse, anxiety, betrayal, bitterness, breaking point, burnout, collapse, danger, death, desperation, discouragement, divorce, exhaustion, frustration, grind, hardships, hazing, hurdles, ignorance, impossible dream, isolation, killing the spirit, leaving, loneliness, murder, neglect, peril, ridicule, ritual, self-protection, sexual harassment, shock, snobbery, strain, strangulation, stress, suffering, suicide, survival of the fittest, trauma, and violence.

  19. Grinding analysis of Indian coal using response surface methodology

    Institute of Scientific and Technical Information of China (English)

    Twinkle Singh; Aishwarya Awasthi; Pranjal Tripathi; Shina Gautam; Alok Gautam

    2016-01-01

    The present work discusses a systematic approach to model grinding parameters of coal in a ball mill.A three level Box-Behnken design combined with response surface methodology using second order model was applied to the experiments done according to the model requirement.Three parameters ball charge (numbers 10-20),coal content (100-200 g) and the grinding time (4-8 min) were chosen for the experiments as well as for the modeling work.Coal fineness is defined as the d80 (80 % passing size).A quadratic model was developed to show the effect of parameters and their interaction with fineness of the product.Three different sizes (4,1 and 0.65 mm) of Indian coal were used.The model equations for each fraction were developed and different sets of experiments were performed.The predicted values of the fineness of coal were in good agreement with the experimental results (R2 values of d80 varies between 0.97 and 0.99).Fine size of three different coal sizes were obtained with larger ball charge with less grinding time and less solid content.This work represents the efficient use of response surface methodology and the Box-Behnken design use for grinding of Indian coal.

  20. Microstructure studies of the grinding damage in monocrystalline silicon wafers

    Institute of Scientific and Technical Information of China (English)

    ZHANG Yinxia; KANG Renke; GUO Dongming; JIN Zhuji

    2007-01-01

    The depth and nature of the subsurface damage in a silicon wafer will limit the performance of IC components.Damage microstructures of the silicon wafers ground by the #325,#600, and #2000 grinding wheels was analyzed.The results show that many microcracks,fractures, and dislocation rosettes appear in the surface and subsurface of the wafer ground by the #325 grinding wheel.No obvious microstructure change exists.The amorphous layer with a thickness of about 100 nm,microcracks, high density dislocations,and polycrystalline silicon are observed in the subsurface of the wafer ground by the #600 grinding wheel.For the wafer ground by the #2000 grinding wheel,an amorphous layer of about 30 nm thickness,a polycrystalline silicon layer,a few dislocations,and an elastic deformation layer exist.In general,with the decrease in grit size,the material removal mode changes from micro-fracture mode to ductile mode gradually.

  1. Facial lesions in piglets with intact or grinded teeth

    Directory of Open Access Journals (Sweden)

    Hansson Monica

    2012-04-01

    Full Text Available Abstract Background Piglets are born with eight sharp teeth that during nursing can cause facial lesions on littermates and teat lesions on the sow. Teeth grinding in piglets is therefore often practiced to reduce these lesions. The aim of this study was to assess the consequences of grinding piglet teeth in regard to the occurrence of lesions. In this study the piglets' teeth were grinded in 28 litters, and in 36 litters the piglets' teeth were kept intact. Twice, one time during the first week and one time during the second week after birth facial lesions of the piglets were scored and the teats of the sows were examined for lesions. The facial lesion score accounted for the amount and severity of lesions. The individual observations on piglets in the litter were synthesized in a litter facial lesion score. Findings 69.8% and 43.5% of the piglets had facial lesions in week 1 and week 2 respectively. The effect of treatment was not significant on litter facial lesion score. The litter facial lesion score was higher in week 1 than in week 2 (p p = 0.003 than in small litters. Mortality between week 1 and week 2 was higher in litters with intact teeth (p = 0.02. Sow teat lesions only occurred if litters had intact teeth. Conclusions According to our results teeth grinding is only justifiable in large litters.

  2. Photoacoustic study of nanocrystalline silicon produced by mechanical grinding

    Energy Technology Data Exchange (ETDEWEB)

    Poffo, C.M. [Departamento de Engenharia Mecanica, Universidade Federal de Santa Catarina, Campus Universitario Trindade, C.P. 476, 88040-900 Florianopolis, Santa Catarina (Brazil); Lima, J.C. de, E-mail: fsc1jcd@fisica.ufsc.b [Departamento de Fisica, Universidade Federal de Santa Catarina, Campus Trindade, C.P. 476, 88040-900 Florianopolis, Santa Catarina (Brazil); Souza, S.M.; Triches, D.M. [Departamento de Engenharia Mecanica, Universidade Federal de Santa Catarina, Campus Universitario Trindade, C.P. 476, 88040-900 Florianopolis, Santa Catarina (Brazil); Grandi, T.A. [Departamento de Fisica, Universidade Federal de Santa Catarina, Campus Trindade, C.P. 476, 88040-900 Florianopolis, Santa Catarina (Brazil); Biasi, R.S. de [Secao de Engenharia Mecanica e de Materiais, Instituto Militar de Engenharia, 22290-270 Rio de Janeiro, RJ (Brazil)

    2011-04-01

    Mechanical grinding (MG) was used to produce nanocrystalline silicon and its thermal and transport properties were investigated by photoacoustic absorption spectroscopy (PAS). The experimental results suggest that in as-milled nanocrystalline silicon for 10 h the heat transfer through the crystalline and interfacial components is similar, and after annealed at 470 {sup o}C the heat transfer is controlled by crystalline component.

  3. Effects of High Pressure ORE Grinding on the Efficiency of Flotation Operations

    Science.gov (United States)

    Saramak, Daniel; Krawczykowska, Aldona; Młynarczykowska, Anna

    2014-10-01

    This article discusses issues related to the impact of the high pressure comminution process on the efficiency of the copper ore flotation operations. HPGR technology improves the efficiency of mineral resource enrichment through a better liberation of useful components from waste rock as well as more efficient comminution of the material. Research programme included the run of a laboratory flotation process for HPGR crushing products at different levels of operating pressures and moisture content. The test results showed that products of the high-pressure grinding rolls achieved better recoveries in flotation processes and showed a higher grade of useful components in the flotation concentrate, in comparison to the ball mill products. Upgrading curves have also been marked in the following arrangement: the content of useful component in concentrate the floatation recovery. All upgrading curves for HPGR products had a more favourable course in comparison to the curves of conventionally grinded ore. The results also indicate that various values of flotation recoveries have been obtained depending on the machine operating parameters (i.e. the operating pressure), and selected feed properties (moisture).

  4. Electronic scraps--recovering of valuable materials from parallel wire cables.

    Science.gov (United States)

    de Araújo, Mishene Christie Pinheiro Bezerra; Chaves, Arthur Pinto; Espinosa, Denise Crocce Romano; Tenório, Jorge Alberto Soares

    2008-11-01

    Every year, the number of discarded electro-electronic products is increasing. For this reason recycling is needed, to avoid wasting non-renewable natural resources. The objective of this work is to study the recycling of materials from parallel wire cable through unit operations of mineral processing. Parallel wire cables are basically composed of polymer and copper. The following unit operations were tested: grinding, size classification, dense medium separation, electrostatic separation, scrubbing, panning, and elutriation. It was observed that the operations used obtained copper and PVC concentrates with a low degree of cross contamination. It was concluded that total liberation of the materials was accomplished after grinding to less than 3 mm, using a cage mill. Separation using panning and elutriation presented the best results in terms of recovery and cross contamination.

  5. Use and User Perception of Electronic Information Resources: A Case Study of Siva Institute of Frontier Technology, India

    Directory of Open Access Journals (Sweden)

    Velmurugan Chandran

    2013-12-01

    Full Text Available The present study aims to explore the use and user perception of electronic resources in Siva Institute of Frontier Technology, India. A total number of 123 users were taken into account for the study through a questionnaire-based survey method. A well-structured questionnaire was designed and distributed to the selected 200 students and staff members. 123 copies of the questionnaires were returned dully filled in and the overall response rate was 61.50 percent. The questionnaire contained both open- and close-ended questions. The collected data were classified, analyzed, and tabulated by using simple statistical methods. This study covers the impact of electronic resources on students and faculty in their academic pursuit.

  6. How Human Resource Professionals Use Electronic Channels to Communicate CSR : A case study focused on Solvay's French industrial sites

    OpenAIRE

    Fournet, Clara; Pauly, Marissa

    2015-01-01

    Corporate Social Responsibility (CSR) has become a large concern for many companies with the rise of globalization. Oftentimes, companies are encouraged to communicate CSR externally, but not internally. This research focuses upon the internal communication of CSR, specifically how Human Resource (HR) professionals use electronic channels to communicate to employees. The scope of this research is focused solely upon HR professionals within Solvay’s French industrial sites, which produce chemi...

  7. Challenges in the implementation of an electronic surveillance system in a resource-limited setting: Alerta, in Peru

    Directory of Open Access Journals (Sweden)

    Soto Giselle

    2008-11-01

    Full Text Available Abstract Background Infectious disease surveillance is a primary public health function in resource-limited settings. In 2003, an electronic disease surveillance system (Alerta was established in the Peruvian Navy with support from the U.S. Naval Medical Research Center Detachment (NMRCD. Many challenges arose during the implementation process, and a variety of solutions were applied. The purpose of this paper is to identify and discuss these issues. Methods This is a retrospective description of the Alerta implementation. After a thoughtful evaluation according to the Centers for Disease Control and Prevention (CDC guidelines, the main challenges to implementation were identified and solutions were devised in the context of a resource-limited setting, Peru. Results After four years of operation, we have identified a number of challenges in implementing and operating this electronic disease surveillance system. These can be divided into the following categories: (1 issues with personnel and stakeholders; (2 issues with resources in a developing setting; (3 issues with processes involved in the collection of data and operation of the system; and (4 issues with organization at the central hub. Some of the challenges are unique to resource-limited settings, but many are applicable for any surveillance system. For each of these challenges, we developed feasible solutions that are discussed. Conclusion There are many challenges to overcome when implementing an electronic disease surveillance system, not only related to technology issues. A comprehensive approach is required for success, including: technical support, personnel management, effective training, and cultural sensitivity in order to assure the effective deployment of an electronic disease surveillance system.

  8. Tracking the Flow of Resources in Electronic Waste - The Case of End-of-Life Computer Hard Disk Drives.

    Science.gov (United States)

    Habib, Komal; Parajuly, Keshav; Wenzel, Henrik

    2015-10-20

    Recovery of resources, in particular, metals, from waste flows is widely seen as a prioritized option to reduce their potential supply constraints in the future. The current waste electrical and electronic equipment (WEEE) treatment system is more focused on bulk metals, where the recycling rate of specialty metals, such as rare earths, is negligible compared to their increasing use in modern products, such as electronics. This study investigates the challenges in recovering these resources in the existing WEEE treatment system. It is illustrated by following the material flows of resources in a conventional WEEE treatment plant in Denmark. Computer hard disk drives (HDDs) containing neodymium-iron-boron (NdFeB) magnets were selected as the case product for this experiment. The resulting output fractions were tracked until their final treatment in order to estimate the recovery potential of rare earth elements (REEs) and other resources contained in HDDs. The results further show that out of the 244 kg of HDDs treated, 212 kg comprising mainly of aluminum and steel can be finally recovered from the metallurgic process. The results further demonstrate the complete loss of REEs in the existing shredding-based WEEE treatment processes. Dismantling and separate processing of NdFeB magnets from their end-use products can be a more preferred option over shredding. However, it remains a technological and logistic challenge for the existing system.

  9. The impact of electronic healthcare associated infection surveillance software on infection prevention resources: A systematic review of the literature.

    Science.gov (United States)

    Russo, Philip L; Shaban, Ramon Z; MacBeth, Deborough; Carter, Abigail; Mitchell, Brett G

    2017-09-08

    Surveillance of healthcare-associated infections is fundamental for infection prevention. The methods and practices for surveillance have evolved as technology becomes more advanced. The availability of electronic surveillance software (ESS) has increased, and yet adoption of ESS is slow. It is argued that ESS deliver savings through automation, particularly in terms of human resourcing and infection prevention (IP) staff time. This paper describes the findings of a systematic review on the impact of ESS on IP resources. A systematic search was conducted of electronic databases Medline and the Cumulative Index to Nursing and Allied Health Literature published between 1st January 2006 and 31(st) December 2016 with analysis using Newcastle-Ottawa Scale. 2832 articles were reviewed of which 16 studies met the inclusion criteria. IP resources were identified as time undertaken on surveillance. A reduction in IP staff time to undertake surveillance was demonstrated in 13 studies. The reduction proportion ranged from 12.5% - 98.4% (mean 73.9%). The remaining three did not allow for any estimation of the effect in terms of IP staff time. None of the studies demonstrated an increase in IP staff time. The results of this review demonstrate that adopting ESS yield considerable dividends in IP staff time relating to data collection and case ascertainment whilst maintaining high levels of sensitivity and specificity. This has the potential to enable reinvestment into other components of IP to maximise efficient use of scare IP resources. Copyright © 2017. Published by Elsevier Ltd.

  10. Photoluminescence of MoS2 Prepared by Effective Grinding-Assisted Sonication Exfoliation

    Directory of Open Access Journals (Sweden)

    Jing-Yuan Wu

    2014-01-01

    Full Text Available Exfoliation of bulk molybdenum disulfide (MoS2 using sonication in appropriate solvent is a promising route to large-scale preparation of few-layered or monolayered crystals. Grinding-assisted sonication exfoliation was used for preparing monolayered MoS2 nanosheets from natural mineral molybdenite. By controlling the sonication time, larger crystallites could be further exfoliated to smaller as well as thinner nanosheets without damaging their structures. The concentration of 1.6 mg mL−1 of final solution could be achieved. Several microscopic techniques like scanning electron microscopy, transmission electron microscopy, and atomic force microscopy were employed to evaluate the exfoliation results. Strong photoluminescence with the peak centered at 440 nm was also observed in the resulting dispersion which included several small lateral-sized (~3 nm nanostructures.

  11. HELP (INFORMATION ELECTRONIC RESOURCE "CHRONICLE OF ONU: DATES, FACTS, EVENTS": HISTORY OF UNIVERSITY IN INFORMATION SPACE

    Directory of Open Access Journals (Sweden)

    А. М. Гавриленко

    2016-03-01

    Object of research is the help information resource "The chronicle of the Odessa national university of I. I. Mechnikov: dates, facts, events". The main objective of our article – to state the main methodological bases of creation of information resource. One of advantages of information resource is possibility of continuous updating and replenishment by new information. Main objective of creation of this information resource is systematization of material on stories of the Odessa national university of I. I. Mechnikov from the date of his basis to the present, ensuring interactive access to information on the main dates, the most significant events in life of university. The base of research are sources on the history of university, chronology of historical development, formation of infrastructure, cadres and scientific researches. In information resource the main stages of development, functioning and transformation of the Odessa University are analyzed, information on its divisions is collected. For creation of this information resource in Scientific library the method of work was developed, the main selection criteria of data are allocated. This information resource have practical value for all who is interested in history of university, historians, scientists-researchers of history of science and the city of Odessa.

  12. Development of ELID mirror surface grinding by cast iron bond grinding wheel. Ohkochi memorial technology prize; Chutetsu bond toishi ni yoru denkai inpurosesu doresshingu (ELID) kyomen kensakuho no kaihatsu. Okochi kinen gijutsusho jusho ni yosete

    Energy Technology Data Exchange (ETDEWEB)

    Omori, H.; Takahashi, I. [Institute of Physical and Chemical Research, Tokyo (Japan); Nakagawa, T. [The University of Tokyo, Tokyo (Japan). Institute of Industrial Science; Hagiuda, Y.; Karikome, K. [Tokyo Metropolitan College of Aeronautical Engineering, Tokyo (Japan)

    1997-08-01

    Development was accomplished on the electrolytic in-process dressing (ELID) mirror surface grinding process using a cast iron bonded grinding wheel. This paper describes the history of the development, which may be summarized as follows: a study was begun on powder forging of cutting chips in 1970; a research was started on powder forging of decarburized cast iron powder; developments were made on powder metallurgy of cast irons and cast iron bonded lapping tools in 1980, and cast iron bonded diamond grinding wheels were put on the market; a high-efficiency grinding process using MC and cast iron fiber-bonded grinding wheels were developed in 1985 and the grinding wheels made therefrom were put on the market; and a study was begun on the ELID grinding in 1987, and marketing was started on power supply, grinding liquid and tools for the ELID grinding process in 1990. Discussions on converting raw materials for the powder forging into cutting chips have triggered developing the cast iron bonded grinding wheel. The cast iron bonded diamond grinding wheel improves dressability and sharpness of conventional grinding wheels. The grinding wheel is fabricated by mixing carbonyl iron powder, diamond grinding grains and cast iron powder, pressing the mixture in a die, sintering it at 1140 degC, and assembling and dressing the sinter. The grinding stone can grind high-tech materials. 4 figs.

  13. A 6-DOF parallel bone-grinding robot for cervical disc replacement surgery.

    Science.gov (United States)

    Tian, Heqiang; Wang, Chenchen; Dang, Xiaoqing; Sun, Lining

    2017-05-24

    Artificial cervical disc replacement surgery has become an effective and main treatment method for cervical disease, which has become a more common and serious problem for people with sedentary work. To improve cervical disc replacement surgery significantly, a 6-DOF parallel bone-grinding robot is developed for cervical bone-grinding by image navigation and surgical plan. The bone-grinding robot including mechanical design and low level control is designed. The bone-grinding robot navigation is realized by optical positioning with spatial registration coordinate system defined. And a parametric robot bone-grinding plan and high level control have been developed for plane grinding for cervical top endplate and tail endplate grinding by a cylindrical grinding drill and spherical grinding for two articular surfaces of bones by a ball grinding drill. Finally, the surgical flow for a robot-assisted cervical disc replacement surgery procedure is present. The final experiments results verified the key technologies and performance of the robot-assisted surgery system concept excellently, which points out a promising clinical application with higher operability. Finally, study innovations, study limitations, and future works of this present study are discussed, and conclusions of this paper are also summarized further. This bone-grinding robot is still in the initial stage, and there are many problems to be solved from a clinical point of view. Moreover, the technique is promising and can give a good support for surgeons in future clinical work.

  14. Research on the Monitoring System of CNC Grinding Process Based on Acoustic Emission

    Institute of Scientific and Technical Information of China (English)

    HU Zhongxiang; TENG Jiaxu; YANG Junwei; HUO Xiaojing; SHI Xiaojun

    2006-01-01

    Using on-line monitoring during the CNC grinding process, the hazard case such as the crushing of grinding wheel and various safety accidents could be avoided, and the optimum time for dressing and replacing grinding wheel could also be determined, and hence, the service life of the grinding wheel could be prolonged and grinding quality could be improved. To overcome the limitation of some traditional techniques in which some parameters including the grinding power and force, torque and so on were monitored, the acoustic emission (AE) technique, which provides high sensitivity and responding speed, were developed in the present paper. The mechanism of AE during grinding was reviewed. Moreover, a virtual AE monitoring system, which could monitor the grinding state under different working conditions during the grinding, has been developed based on the Virtual Instruments technique. Some experiments were also performed on the internal grinder. The results showed that the AE signals became stronger with increasing the main shaft speed and grinding depth or decreasing the distance between the AE sensor and grinding area.

  15. Experimental investigation of abrasive electrodischarge grinding of Ti6Al4V titanium alloy

    Directory of Open Access Journals (Sweden)

    R. Święcik

    2009-12-01

    Full Text Available Purpose: This work is focused on determination of effects of grinding conditions on effectiveness of abrasive electrodischarge grinding (AEDG process applied for removal of machining allowance and forming of surface geometrical texture (SGT. These results were compared with one obtained for conventional grinding.Design/methodology/approach: The experimental investigations of deep-seated surface grinding of Ti6Al4V titanium alloy using CBN grinding wheel with metal bond were the ground for this elaboration. The effectiveness of AEDG process was assessed based on specific tangential grinding force and energy of spark electric discharge and machining results were estimated on geometrical structure parameters.Findings: The effectiveness of machining allowance removal depended on conditions of AEDG process. Significant differences in SGT formed by AEDG process and conventional grinding were revealed.Practical implications: Abrasive electrodischarge grinding is useful to be particularly suitable for efficient and effective grinding of very hard structural materials such as high-alloy steel, sintered carbides, metal-based composite materials etc.Originality/value: AEDG experiments were carried out using the typical surface finishing grinder and especially adapted generator of spark discharge pulses. The majority of such experiments in the world were performed with the electrodischarge machine tool equipped with extra grinding wheel mounted on the grinding pin and functioning as one of the electrodes put into operation via pneumatic drive.

  16. The effect of grinding on the mechanical behavior of Y-TZP ceramics: A systematic review and meta-analyses.

    Science.gov (United States)

    Pereira, G K R; Fraga, S; Montagner, A F; Soares, F Z M; Kleverlaan, C J; Valandro, L F

    2016-10-01

    The aim of this study was to systematically review the literature to assess the effect of grinding on the mechanical properties, structural stability and superficial characteristics of Y-TZP ceramics. The MEDLINE via PubMed and Web of Science (ISI - Web of Knowledge) electronic databases were searched with included peer-reviewed publications in English language and with no publication year limit. From 342 potentially eligible studies, 73 were selected for full-text analysis, 30 were included in the systematic review with 20 considered in the meta-analysis. Two reviewers independently selected the studies, extracted the data, and assessed the risk of bias. Statistical analyses were performed using RevMan 5.1, with random effects model, at a significance level of 0.05. A descriptive analysis considering phase transformation, Y-TZP grain size, Vickers hardness, residual stress and aging of all included studies were executed. Four outcomes were considered in the meta-analyses (factor: grinding x as-sintered) in global and subgroups analyses (grinding tool, grit-size and cooling) for flexural strength and roughness (Ra) data. A significant difference (p<0.05) was observed in the global analysis for strength, favoring as-sintered; subgroup analyses revealed that different parameters lead to different effects on strength. In the global analysis for roughness, a significant difference (p<0.05) was observed between conditions, favoring grinding; subgroup analyses revealed that different parameters also lead to different effects on roughness. High heterogeneity was found in some comparisons. Generally grinding promotes decrease in strength and increase in roughness of Y-TZP ceramics. However, the use of a grinding tool that allows greater accuracy of the movement (i.e. contra angle hand-pieces coupled to slowspeed turbines), small grit size (<50μm) and the use of plenty coolant seem to be the main factors to decrease the defect introduction and allow the occurrence of the

  17. Research into Grinding Hardening of Microalloyed Non-quenched and Tempered Steel

    Institute of Scientific and Technical Information of China (English)

    HAN Zheng-tong; ZHANG Ning-ju; GAO Ding; YANG Gang

    2007-01-01

    Grinding hardening is a new technology of hardening steel piece surfaces with grinding heat generated in the grinding process instead of with a high or medium frequency induction heating method, which can effectively integrate grinding and surface hardening. Experimental studies were carried out on grinding hardening of non-quenched and tempered steel. Through grinding experiments with variable depths of cut and feeding rate, the variation in the depth of the hardening layer was studied and the microstructure of the hardening zone of the test pieces was subsequently analyzed. In the end, the hardening effect of non-quenched and tempered steel was compared with that of 40Cr steel, which revealed the superiority of non-quenched and tempered steel in grinding hardening technology.

  18. Development of a grinding-specific performance test set-up

    DEFF Research Database (Denmark)

    Olesen, C. G.; Larsen, B. H.; Andresen, E. L.

    2015-01-01

    and an exponentially rising resistance. A custom-made grinding ergometer was developed with computer-controlled resistance and capable of collecting data during the test. The data collected can be used to find measures of grinding performance such as peak power, time to complete and the decline in repeated grinding......The aim of this study was to develop a performance test set-up for America's Cup grinders. The test set-up had to mimic the on-boat grinding activity and be capable of collecting data for analysis and evaluation of grinding performance. This study included a literature-based analysis of grinding...... demands and a test protocol developed to accommodate the necessary physiological loads. This study resulted in a test protocol consisting of 10 intervals of 20 revolutions each interspersed with active resting periods of 50 s. The 20 revolutions are a combination of both forward and backward grinding...

  19. Influence of mechanical grinding on lithium insertion and extraction properties of iron silicide/silicon composites

    Science.gov (United States)

    Usui, Hiroyuki; Nouno, Kazuma; Takemoto, Yuya; Nakada, Kengo; Ishii, Akira; Sakaguchi, Hiroki

    2014-12-01

    We prepared composite electrodes of iron silicide/Si by using mechanical grinding for mixtures of ferrosilicon and Si followed by gas-deposition, and investigated their electrochemical properties as Li-ion battery anode. With increasing the mechanical grinding time, the phase transformation from FeSi to FeSi2 took place more significantly, and the composite electrode showed better cycle stabilities. There was no remarkable difference in mechanical properties and electronic conductivity between FeSi and FeSi2. On the other hand, the FeSi2 electrode exhibited about three times larger capacities in comparison with the FeSi electrode. In addition, a result of our first principle calculation indicates that Li-ion can diffuse more easily in FeSi2 lattice than in FeSi lattice. It is suggested that the better cyclability of the composite electrodes was attributed to the moderate reactivity of FeSi2 with Li and the smooth Li-ion diffusion in it.

  20. Effect of Access to an Electronic Medical Resource on Performance Characteristics of a Certification Examination: A Randomized Controlled Trial.

    Science.gov (United States)

    Lipner, Rebecca S; Brossman, Bradley G; Samonte, Kelli M; Durning, Steven J

    2017-09-05

    Electronic resources are increasingly used in medical practice. Their use during high-stakes certification examinations has been advocated by many experts, but whether doing so would affect the capacity to differentiate between high and low abilities is unknown. To determine the effect of electronic resources on examination performance characteristics. Randomized controlled trial. Medical certification program. 825 physicians initially certified by the American Board of Internal Medicine (ABIM) who passed the Internal Medicine Certification examination or sat for the Internal Medicine Maintenance of Certification (IM-MOC) examination in 2012 to 2015. Participants were randomly assigned to 1 of 4 conditions: closed book using typical or additional time, or open book (that is, UpToDate [Wolters Kluwer]) using typical or additional time. All participants took the same modified version of the IM-MOC examination. Primary outcomes included item difficulty (how easy or difficult the question was), item discrimination (how well the question differentiated between high and low abilities), and average question response time. Secondary outcomes included examination dimensionality (that is, the number of factors measured) and test-taking strategy. Item response theory was used to calculate question characteristics. Analysis of variance compared differences among conditions. Closed-book conditions took significantly less time than open-book conditions (mean, 79.2 seconds [95% CI, 78.5 to 79.9 seconds] vs. 110.3 seconds [CI, 109.2 to 111.4 seconds] per question). Mean discrimination was statistically significantly higher for open-book conditions (0.34 [CI, 0.32 to 0.35] vs. 0.39 [CI, 0.37 to 0.41] per question). A strong single dimension showed that the examination measured the same factor with or without the resource. Only 1 electronic resource was evaluated. Inclusion of an electronic resource with time constraints did not adversely affect test performance and did not change

  1. Understanding intention to use electronic information resources: A theoretical extension of the technology acceptance model (TAM).

    Science.gov (United States)

    Tao, Donghua

    2008-11-06

    This study extended the Technology Acceptance Model (TAM) by examining the roles of two aspects of e-resource characteristics, namely, information quality and system quality, in predicting public health students' intention to use e-resources for completing research paper assignments. Both focus groups and a questionnaire were used to collect data. Descriptive analysis, data screening, and Structural Equation Modeling (SEM) techniques were used for data analysis. The study found that perceived usefulness played a major role in determining students' intention to use e-resources. Perceived usefulness and perceived ease of use fully mediated the impact that information quality and system quality had on behavior intention. The research model enriches the existing technology acceptance literature by extending TAM. Representing two aspects of e-resource characteristics provides greater explanatory information for diagnosing problems of system design, development, and implementation.

  2. Fine grinding of brittle minerals and materials by jet mill

    Directory of Open Access Journals (Sweden)

    Lek Sikong

    2008-05-01

    Full Text Available Various variables affecting grinding, such as air pressure, minerals or materials hardness, feed size were investigated.The limitations of grinding of gypsum, barite, ilmenite, quartz and ferrosilicon were also elucidated by means of particlefineness size distribution and morphology of ground products. It was found that:1 The density of particles, which are in the grinding zone affects the product fineness, i.e. higher feed rate resultsin a larger product size. The appropriate feed rate is suggested to be 0.2~0.5 g/s. Moreover, the density and hardness ofminerals or materials tend to have an effect on the product fineness. Heavy minerals, such as barite or ilmenite, exhibit afiner product size than lighter minerals, like quartz. However, for quartz, the higher hardness also results in a larger d50.2 Air pressure is the most vital variable which affects the grinding by a jet mill. The d50 seems to relate to theapplied air pressure as a power law equation expressed as following:d50 = aP b ; as P 0The a-value and b-value have been found to correlate to the feed size. The higher the air pressure applied the finerthe product size attained. Moreover, air pressure has a greater effect on hard minerals than on softer ones.3 Feed size seems to have a small effect on ground the product fineness of soft materials, such as gypsum andbarite, but a significant effect on that of hard materials, such as ferrosilicon and quartz, in particularly by milling at low airpressures of 2~3 kg/cm2.4 For the breakage behavior and morphology of ground materials, it was also found that the minerals having cleavages,such as gypsum and barite, tend to be broken along their cleavage planes. Thus, the particle size distribution of theseproducts becomes narrower. While quartz, ilmenite, and ferrosilicon have shattering and chipping breakage mechanisms,grinding results in angular shapes of the ground products and a wider size distribution. Blocks or platelets and

  3. Building and Managing Electronic Resources in Digital Era in India with Special Reference to IUCAA and NIV, Pune: A Comparative Case Study

    Science.gov (United States)

    Sahu, H. K.; Singh, S. N.

    2015-04-01

    This paper discusses and presents a comparative case study of two libraries in Pune, India, Inter-University Centre for Astronomy and Astrophysics and Information Centre and Library of National Institute of Virology (Indian Council of Medical Research). It compares how both libraries have managed their e-resource collections, including acquisitions, subscriptions, and consortia arrangements, while also developing a collection of their own resources, including pre-prints and publications, video lectures, and other materials in an institutional repository. This study illustrates how difficult it is to manage electronic resources in a developing country like India, even though electronic resources are used more than print resources. Electronic resource management can be daunting, but with a systematic approach, various problems can be solved, and use of the materials will be enhanced.

  4. Print and Electronic Resources: Usage Statistics at Guru Gobind Singh Indraprastha University Library

    Science.gov (United States)

    Kapoor, Kanta

    2010-01-01

    Purpose: The purpose of this paper is to quantify the use of electronic journals in comparison with the print collections in the Guru Gobind Singh Indraprastha University Library. Design/methodology/approach: A detailed analysis was made of the use of lending services, the Xerox facility and usage of electronic journals such as Science Direct,…

  5. Print and Electronic Resources: Usage Statistics at Guru Gobind Singh Indraprastha University Library

    Science.gov (United States)

    Kapoor, Kanta

    2010-01-01

    Purpose: The purpose of this paper is to quantify the use of electronic journals in comparison with the print collections in the Guru Gobind Singh Indraprastha University Library. Design/methodology/approach: A detailed analysis was made of the use of lending services, the Xerox facility and usage of electronic journals such as Science Direct,…

  6. Grinding Wear Behaviour of Stepped Austempered Ductile Iron as Media Material During Comminution of Iron Ore in Ball Mills

    Science.gov (United States)

    Raghavendra, H.; Bhat, K. L.; Udupa, K. Rajendra; Hegde, M. M. Rajath

    2011-01-01

    An attempt has been made to evaluate the suitability of austempered ductile iron (ADI) as media material for grinding iron ore in a ball mill. Spheroidal graphite (S.G) iron balls are austenitised at 900° C for 60 minutes and given stepped austempering treatment at 280° C for 30 minutes and 60 minutes followed by 380° C for 60 minutes in each case. These materials are characterised by measuring hardness, analysing X-ray diffraction (X-RD), studying microstructure using optical and scanning electron microscope (SEM). Grinding wear behaviour of these materials was assessed for wear loss in wet condition at different pH value of the mineral slurry and found that the wear rate of grinding media material decreases with increase in pH of the slurry. The wear resistance of ADI balls were compared with forged En31 steel balls and found that the stepped austempered ductile iron is superior to forged En31 steel balls.

  7. Teeth Grinding: Is Emotional Stability related to Bruxism?

    Science.gov (United States)

    Sutin, Angelina R.; Terracciano, Antonio; Ferrucci, Luigi; Costa, Paul T.

    2010-01-01

    This study examines the association between personality traits and bruxism, the repetitive grinding or clenching of teeth. Community-dwelling participants (N = 470) had a comprehensive oral examination by a dentist and completed a dental history and personality questionnaires. Consistent with the literature on state anxiety and depression as antecedents of bruxism, Neuroticism-related traits were associated with self-reported teeth grinding. These traits were also associated with other oral complaints often associated with anxiety (jaw clicks, difficulty chewing food, and dry mouth), but not with more general oral health complaints (unhealthy gums, bleeding gums, and canker sores) or with dentist-assessed occlusal wear or tongue indentations. This study provides evidence for the association between Neuroticism and bruxism and other stress-related oral health symptoms. PMID:20835403

  8. Repair grinding -- An alternative to ultrasonic rejection for oilfield tubes

    Energy Technology Data Exchange (ETDEWEB)

    Stanley, R.K. (NDE Information Consultants, Houston, TX (United States))

    1994-10-01

    The price of scrap steel rose from $95 to $140/ton in 1993, making tubular production costs higher and making internal repair grinding of oil field tubes with minor internal surface breaking imperfections an extremely cost effective method for placing potentially reject tubulars back into service. Such imperfections often occur and are presently sized by the shear wave ultrasonic amplitude method. This article is written to illustrate how effective repair grinding can be in producing prime material within the API specifications 5CT, specification for Casing and Tubing; 5D, Specification for Drill Pipe; and 5L, Line Pipe. Ninety percent of high grade and 50--60% of midgrade materials can be saved by this method.

  9. Teeth Grinding: Is Emotional Stability related to Bruxism?

    Science.gov (United States)

    Sutin, Angelina R; Terracciano, Antonio; Ferrucci, Luigi; Costa, Paul T

    2010-06-01

    This study examines the association between personality traits and bruxism, the repetitive grinding or clenching of teeth. Community-dwelling participants (N = 470) had a comprehensive oral examination by a dentist and completed a dental history and personality questionnaires. Consistent with the literature on state anxiety and depression as antecedents of bruxism, Neuroticism-related traits were associated with self-reported teeth grinding. These traits were also associated with other oral complaints often associated with anxiety (jaw clicks, difficulty chewing food, and dry mouth), but not with more general oral health complaints (unhealthy gums, bleeding gums, and canker sores) or with dentist-assessed occlusal wear or tongue indentations. This study provides evidence for the association between Neuroticism and bruxism and other stress-related oral health symptoms.

  10. Efficient Fuel Pretreatment: Simultaneous Torrefaction and Grinding of Biomass

    DEFF Research Database (Denmark)

    Saleh, Suriyati Binti; Hansen, Brian Brun; Jensen, Peter Arendt

    2013-01-01

    Combining torrefaction and grinding of biomass in one reactor may be an attractive fuel pretreatment process. A combined laboratory torrefaction and ball mill reactor has been constructed for studies of the influence of temperature and residence time on the product yields and particle size......, and ash composition, where straw has a higher alkali content. This and other studies indicate that the large difference in the alkali contents of the biomasses is the main cause for the observed difference in torrefaction characteristics. Experiments with separate particle heating and grinding showed...... of straw for 90 min yielded a higher mass loss (27–60 wt %) and relative size reduction (59–95%) compared with spruce (mass loss of 10–56 wt % and size reduction of 20–60%). The two types of biomass investigated differ with respect to hemicellulose type, lignocellulosic composition, particle morphology...

  11. Study of CNC Grinding Machining Method About Isometric Polygon Profile

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The formed principle and CNC grinding machining method of isometric polygonal profile are studied deeply and systematically. Equation about section curve of isometric polygon profile is set up by means of geometric principle. With the use of differential geometry theory, the curve is proved to be with geometric feature of convex curve. It is referred to as Isometric Polygonal Curve (IPC), because that is a kind of convex curve on which the distance between any parallel tangent lines is equal. Isometric Poly...

  12. Respiratory Diseases in Agate Grinding Workers in Iran

    Directory of Open Access Journals (Sweden)

    E Rafeemanesh

    2014-07-01

    Full Text Available Background: Agate is a hard silica stone with bands of various colors, which is used in jewelry. The agate grinding workers are exposed to silica dust.Objective: To determine the prevalence of respiratory diseases in agate grinding workers and the associated factors.Methods: In this cross-sectional study, 170 agate grinding workers from Mashhad, northeastern Iran, were examined. Medical and occupational history for respiratory illnesses was taken using respiratory questionnaire of the national program of silicosis control, lung examination, spirometry and chest radiography. Chest x-rays were interpreted according to the International Labor Office (ILO classification system, 2000.Results: The mean±SD of age and work duration of the participants were 31.2±10.1 and 13±8.2 years, respectively. The prevalence of silicosis among agate workers was 12.9% (95% CI: 7.9%–18.0%; 18 workers had simple and 4 had complicated silicosis. There was a significant (p<0.05 relationship between contracting silicosis and exposure duration. 20 (11.7% workers had symptoms consistent with chronic bronchitis and 8 (4.7% showed asthma and asthma-like symptoms. The most frequent disorder observed in spirometry was the restrictive pattern (n=43, 30%. In the agate grinders, clinical and spirometry findings did not match with radiological findings.Conclusion: Agate grinding workers are at increased risk for respiratory diseases, specifically for silicosis and chronic bronchitis. The disease is related to silica dust exposure, poor ventilation and inappropriate personal protection.

  13. FRACTURE FEATURES OF METAL BINDING WHEN DIAMOND-SPARK GRINDING

    Directory of Open Access Journals (Sweden)

    Yury GUTSALENKO

    2012-05-01

    Full Text Available The hypothesis of the influence of binding energy of metal on the processes of destruction and mass transfer at high-speed machining is considered. Some nonconventional processes of cleaning of intergranularity spaces from waste products at diamond-spark grinding are explained, the approach to assessment of metal resistance in these processes is proposed and eo ipso modern conception of processes in chip formation zone under condition of electric discharge effect is supplemented

  14. Intention to use and actual use of electronic information resources: further exploring Technology Acceptance Model (TAM).

    Science.gov (United States)

    Tao, Donghua

    2009-11-14

    Following up a previous study that examined public health students' intention to use e-resources for completing research paper assignments, the present study proposed two models to investigate whether or not public health students actually used the e-resources they intended to use and whether or not the determinants of intention to use predict actual use of e-resources. Focus groups and pre- and post-questionnaires were used to collect data. Descriptive analysis, data screening, and Structural Equation Modeling (SEM) techniques were used for data analysis. The study found that the determinants of intention-to-use significantly predict actual use behavior. Direct impact of perceived usefulness and indirect impact of perceived ease of use to both behavior intention and actual behavior indicated the importance of ease of use at the early stage of technology acceptance. Non-significant intention-behavior relationship prompted thoughts on the measurement of actual behavior and multidimensional characteristics of the intention construct.

  15. Poly(ethylene glycols as grinding additives in the mechanochemical preparation of highly functionalized 3,5-disubstituted hydantoins

    Directory of Open Access Journals (Sweden)

    Andrea Mascitti

    2017-01-01

    Full Text Available The mechanochemical preparation of highly functionalized 3,5-disubstituted hydantoins was investigated in the presence of various poly(ethylene glycols (PEGs, as safe grinding assisting agents (liquid-assisted grinding, LAG. A comparative study under dry-grinding conditions was also performed. The results showed that the cyclization reaction was influenced by the amount of the PEG grinding agents. In general, cleaner reaction profiles were observed in the presence of PEGs, compared to dry-grinding procedures.

  16. Can seeds help mice with the daily grind?

    Science.gov (United States)

    Pritchett-Corning, K R; Keefe, R; Garner, J P; Gaskill, B N

    2013-10-01

    Some laboratory mice gnaw food pellets without ingesting much of the gnawed material, resulting in the production of waste material called 'orts'. The fact that this food grinding behavior is not seen in all individuals of a particular strain suggests that it might be abnormal, and thus indicate a welfare concern. Furthermore, the increased rate of feed consumption and cage soiling is undesirable from a husbandry perspective. To try to determine possible motivations for the behavior, and identify potential treatments, outbred Crl:CD1(Icr) mice exhibiting food grinding were selected for one of three treatments placed in the feeder: no enrichment, a chewing device, or sunflower seeds. Both enrichment groups showed a significant decrease (P food wastage after the treatment was withdrawn. A relationship between body weight and ort production was also found, in that cages with greater average body weights had lower levels of ort production. This suggests that a simple need to gnaw cannot alone explain food grinding, and that a nutritional motivation may also be involved.

  17. Rotary ultrasonic machining of CFRP: A comparison with grinding.

    Science.gov (United States)

    Ning, F D; Cong, W L; Pei, Z J; Treadwell, C

    2016-03-01

    Carbon fiber reinforced plastic (CFRP) composites have been intensively used in various industries due to their superior properties. In aircraft and aerospace industry, a large number of holes are required to be drilled into CFRP components at final stage for aircraft assembling. There are two major types of methods for hole making of CFRP composites in industry, twist drilling and its derived multi-points machining methods, and grinding and its related methods. The first type of methods are commonly used in hole making of CFRP composites. However, in recent years, rotary ultrasonic machining (RUM), a hybrid machining process combining ultrasonic machining and grinding, has also been successfully used in drilling of CFRP composites. It has been shown that RUM is superior to twist drilling in many aspects. However, there are no reported investigations on comparisons between RUM and grinding in drilling of CFRP. In this paper, these two drilling methods are compared in five aspects, including cutting force, torque, surface roughness, hole diameter, and material removal rate.

  18. Physical characterization of coffee after roasting and grinding

    Directory of Open Access Journals (Sweden)

    Gabriel Henrique Horta de Oliveira

    2014-09-01

    Full Text Available Flowability is an important characteristic of handling process for efficiency and reliability purpose of post-harvest operations, which are governed by the physical properties of the product. Physical properties determination is an important factor for formulation of machinery projects and sizing of post-harvest operations, which may impact considerably on the products quality, influencing directly the operation cost and company profit. Thus, the objective of this work was to evaluate and determinate some physical properties (repose angle, unit and bulk density, porosity and color coordinates, particle size, moisture content, water activity, angle of internal friction and effective angle of internal friction of coffee, such as to evaluate the influence of different roast and grinding degrees over these properties. Crude grain coffee (Coffea canephora and Coffea arabica, dehulled and dried were used. These were roasted at two levels: medium light and medium-dark brown, which Agtron numbers are, respectively, SCAA#65 and SCAA#45. After roasting process, grains were grinded at three particle sizes (thin, medium and thick. Both particle size and roast degree significantly affected physical properties of coffee. Coffee samples roasted at medium dark level obtained lower values of moisture content, water activity, repose angle, bulk and real density. Coffee samples grinded at level thin presented an increase of angle of internal friction and effective angle of internal friction, repose angle, bulk and real density, porosity and decrease of water activity values.

  19. MendelWeb: An Electronic Science/Math/History Resource for the WWW.

    Science.gov (United States)

    Blumberg, Roger B.

    This paper describes a hypermedia resource, called MendelWeb that integrates elementary biology, discrete mathematics, and the history of science. MendelWeb is constructed from Gregor Menders 1865 paper, "Experiments in Plant Hybridization". An English translation of Mendel's paper, which is considered to mark the birth of classical and…

  20. QR Codes as Finding Aides: Linking Electronic and Print Library Resources

    Science.gov (United States)

    Kane, Danielle; Schneidewind, Jeff

    2011-01-01

    As part of a focused, methodical, and evaluative approach to emerging technologies, QR codes are one of many new technologies being used by the UC Irvine Libraries. QR codes provide simple connections between print and virtual resources. In summer 2010, a small task force began to investigate how QR codes could be used to provide information and…

  1. Electronic resources at the University of Sharjah medical library: an investigation of students' information-seeking behavior.

    Science.gov (United States)

    Boumarafi, Behdja

    2010-10-01

    Electronic information is becoming prevalent worldwide, and its use is growing exponentially as more and more users are recognizing the potential that it offers in terms of access and delivery. However, with the introduction of new tools for e-information searching and retrieval, users have to readjust their information-seeking behavior to cope with the corresponding changes. The University of Sharjah library is steadily increasing its investment in e-resources to offer ubiquitous access to the growing body of literature in areas that interest the community it serves. This study reports the findings of a survey conducted to investigate the information-seeking behavior of medical students at the medical library. Results showed evidence of use of e-resources, but they did not explicitly establish that some of the major problems mentioned by participants did hinder the information searches of the respondents. An extensive literature review sets the background for the study.

  2. 图书馆电子信息资源利用效果评价研究%Study on Utilization Effect Evaluation of Library Electronic Information Resources

    Institute of Scientific and Technical Information of China (English)

    晋晓强; 贺培风; 何忠印

    2012-01-01

    This paper discusses utilization effect of electronic information resources combining with the characteristics of electronic information resources, makes evaluation system of library electronic information resource utilization effect from three aspects : the library, the users and the data providers, hoping for providing valuable reference for the efficient use of library electronic resources.%本文结合电子信息资源的特性对电子信息资源的利用进行初步探讨,从图书馆、用户和数据服务商三个角度构建图书馆电子信息资源利用效果的评价体系,希望能为图书馆电子信息资源的高效利用提供参考。

  3. Finishing of additively manufactured titanium alloy by shape adaptive grinding (SAG)

    Science.gov (United States)

    Beaucamp, Anthony T.; Namba, Yoshiharu; Charlton, Phillip; Jain, Samyak; Graziano, Arthur A.

    2015-06-01

    In recent years, rapid prototyping of titanium alloy components for medical and aeronautics application has become viable thanks to advances in technologies such as electron beam melting (EBM) and selective laser sintering (SLS). However, for many applications the high surface roughness generated by additive manufacturing techniques demands a post-finishing operation to improve the surface quality prior to usage. In this paper, the novel shape adaptive grinding process has been applied to finishing titanium alloy (Ti6Al4V) additively manufactured by EBM and SLS. It is shown that the micro-structured surface layer resulting from the melting process can be removed, and the surface can then be smoothed down to less than 10 nm Ra (starting from 4-5 μm Ra) using only three different diamond grit sizes. This paper also demonstrates application of the technology to freeform shapes, and documents the dimensional accuracy of finished artifacts.

  4. GRINDING OF HARDENED STEELS USING OPTIMIZED COOLING RECTIFICADO DE ACEROS ENDURECIDOS USANDO REFRIGERACIÓN OPTIMIZADA

    Directory of Open Access Journals (Sweden)

    Manoel Cléber de Sampaio Alves

    2008-06-01

    Full Text Available Grinding – the final machining process of a workpiece – requires large amounts of cutting fluids for the lubrication, cooling and removal of chips. These fluids are highly aggressive to the environment. With the technological advances of recent years, the worldwide trend is to produce increasingly sophisticated components with very strict geometric and dimensional tolerances, good surface finish, at low costs, and particularly without damaging the environment. The latter requirement can be achieved by recycling cutting fluids, which is a costly solution, or by drastically reducing the amount of cutting fluids employed in the grinding process. This alternative was investigated here by varying the plunge velocity in the plunge cylindrical grinding of ABNT D6 steel, rationalizing the application of two cutting fluids and using a superabrasive CBN (cubic boron nitride grinding wheel with vitrified binder to evaluate the output parameters of tangential cutting force, acoustic emission, roughness, roundness, tool wear, residual stress and surface integrity, using scanning electron microscopy (SEM to examine the test specimens. The performance of the cutting fluid, grinding wheel and plunge velocity were analyzed to identify the best machining conditions which allowed for a reduction of the cutting fluid volume, reducing the machining time without impairing the geometric and dimensional parameters, and the surface finish and integrity of the machined components.La rectificación, proceso final de fabricación de una pieza, hace uso intenso de fluidos de corte con la finalidad de lubricación, refrigeración y remoción de astillas (imperfecciones. Sin embargo, estos fluidos son extremamente agresivos al medio. Con el avance tecnológico la tendencia mundial es producir piezas cada vez mas sofisticadas, con elevado grado de tolerancia geométrica, dimensional, con buen acabamiento superficial, con bajo costo y, principalmente, sin causar daños al

  5. A Review: The Effect of Grinded Coal Bottom Ash on Concrete

    Directory of Open Access Journals (Sweden)

    Basirun Nurul Fasihah

    2017-01-01

    Full Text Available This paper offers a review on the use of grinded coal bottom ash (CBA on the concrete properties as demonstrated by strength test and microstructure test. Amount of CBA from power plant station was disposed in landfill because of the particle shape had a rough particles. By finding an alternative way to gain its surface area by grinding and used as replacement material as cement replacement may give a good side feedback on the strength and morphology of concrete. Most of the prior works studied on the grinded fly ash and grinded rice husk ash. The study on the influence of grinded CBA on the properties of concrete still limited and need more attention Therefore, the review on the effect of grinded CBA on the strength and microstructure of concrete are discussed.

  6. An Exploratory study on the use of LibAnswers to Resolve, Track and Monitor Electronic Resources Issues: The KAUST Library experience

    KAUST Repository

    Ramli, Rindra M.

    2017-05-03

    An Exploratory study on KAUST library use of LibAnswers in resolving electronic resources questions received in LibAnswers. It describes the findings of the questions received in LibAnswers. The author made suggestions based on the findings to improve the reference services in responding to e-resources questions.

  7. Eavesdropping on Electronic Guidebooks: Observing Learning Resources in Shared Listening Environments.

    Science.gov (United States)

    Woodruff, Allison; Aoki, Paul M.; Grinter, Rebecca E.; Hurst, Amy; Szymanski, Margaret H.; Thornton, James D.

    This paper describes an electronic guidebook, "Sotto Voce," that enables visitors to share audio information by eavesdropping on each others guidebook activity. The first section discusses the design and implementation of the guidebook device, key aspects of its user interface, the design goals for the audio environment, the eavesdropping…

  8. Electronic Resources in a Next-Generation Catalog: The Case of WorldCat Local

    Science.gov (United States)

    Shadle, Steve

    2009-01-01

    In April 2007, the University of Washington Libraries debuted WorldCat Local (WCL), a localized version of the WorldCat database that interoperates with a library's integrated library system and fulfillment services to provide a single-search interface for a library's physical and electronic content. This brief will describe how WCL incorporates a…

  9. Equalizing Access to Electronic Networked Resources: A Model for Rural Libraries in the United States.

    Science.gov (United States)

    Senkevitch, Judith J.; Wolfram, Dietmar

    1994-01-01

    Provides an overview of the current state of networking technology in rural libraries and describes a model for educating rural librarians in accessing electronic networks. Topics discussed include information needs in rural libraries; telecommunications technology access in rural areas; and examples of services to enhance information access.…

  10. Effect of Grinding Temperatures on the Surface Integrity of a Nickel-based Superalloy

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    An experimental study was carried out to investigat e the influence of temperatures on workpiece surface integrity in surface grinding of a cast nickel-based superalloy with alumina abrasive wheels. Temperatur e response at the wheel-workpiece interface was measured using a grindable foil /workpiece thermocouple. Specimens with different grinding temperatures were obt ained through changing grinding conditions including depth of cut, workpiece fee d speed, and coolant supply. Changes in surface roughnes...

  11. Finite Element Analysis and Experiment Research on Surface Residual Stress of Ceramics Grinding

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The theoretical model of residual stress of ceramics grinding has been established applying thermal elastoplastic mechanics theory. While grinding at the course of grinding wheel moved along workpiece surface the distributing regulation of residual stress can be simplified into thermal elastioplastic mechanical issue, under the action of the both moving centralized force and heat source. Calculating and evaluating of surface residual stress using current procedure of finite element analysis which has been...

  12. Investigation of the Formation Process of Two Piracetam Cocrystals during Grinding

    OpenAIRE

    2011-01-01

    Cocrystal formation rates during dry grinding and liquid-assisted grinding were investigated by X-ray powder diffractometry and Raman spectroscopy. Two polymorphic forms of piracetam were used to prepare known piracetam cocrystals as model substances, i.e., piracetam-citric acid and piracetam-tartaric acid cocrystals. Raman spectroscopy in combination with principal component analysis was used to visualize the cocrystal formation pathways. During dry grinding, cocrystal formation appeared to ...

  13. ELECTRO-RESISTANCE METHOD OF CHECK A PROCESS GRINDING THE ROLLING BEARINGS

    Directory of Open Access Journals (Sweden)

    K. V. Podmasteryev

    2015-01-01

    Full Text Available Base a possibility of monitoring processes of grinding the rolling bearings with use electroresistance method of check. Is write of essence this method, are analyses his peculiarities, which are provide objective information on the condition a object by his grinding. Are consider the results of experimental researches the effective different diagnostically parameters, which are confirm a possibility of realization objective check of grinding the rolling bearings with use electro-resistance method.

  14. The Simulation of Grinding Wheels and Ground Surface Roughness Based on Virtual Reality Technology

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    The paper describes the feasibility and method of the application of virtual reality technology to grinding process, and introduces the modeling method of object entity in the environment of virtual reality. The simulation process of grinding wheels and ground surface roughness is discussed, and the computation program system of numerical simulation is compiled with Visual C++ programming language. At the same time, the three-dimensional simulation models of grinding wheels and ground surface roughness are ...

  15. Optimization of Preventive Grinding of Backup Roll against Contact Fatigue Cracking

    Institute of Scientific and Technical Information of China (English)

    DOU Peng; LI You-guo; LIANG Kai-ming; BAI Bing-zhe

    2005-01-01

    In order to optimize the current grinding procedure of the backup roll of 2050 continuously variable crown (CVC) mills, the behavior of rolling contact fatigue (RCF) cracking was investigated. Two RCF short cracks, including vertical short crack and ratcheting short crack initiated from ratcheting, were observed. The behavior of both RCF cracks was analyzed in detail. Then a modified grinding procedure was proposed according to the behavior of RCF cracks and the preventive grinding strategy.

  16. Preference and Use of Electronic Information and Resources by Blind/Visually Impaired in NCR Libraries in India

    Directory of Open Access Journals (Sweden)

    Shailendra Kumar

    2013-06-01

    Full Text Available This paper aims to determine the preference and use of electronic information and resources by blind/visually impaired users in the leading National Capital Region (NCR libraries of India. Survey methodology has been used as the basic research tool for data collection with the help of questionnaires. The 125 in total users surveyed in all the five libraries were selected randomly on the basis of willingness of the users with experience of working in digital environments to participate in the survey. The survey results were tabulated and analyzed with descriptive statistics methods using Excel software and 'Stata version 11'. The findings reveal that ICT have a positive impact in the lives of people with disabilities as it helps them to work independently and increases the level of confidence among them. The Internet is the most preferred medium of access to information among the majority of blind/visually impaired users. The 'Complexity of content available on the net' is found as the major challenge faced during Internet use by blind users of NCR libraries. 'Audio books on CDs/DVDs and DAISY books' are the most preferred electronic resources among the majority of blind/visually impaired users. This study will help the library professionals and organizations/institutions serving people with disabilities to develop effective library services for blind/visually impaired users in the digital environment on the basis of findings on information usage behavior in the study.

  17. Evaluation of minimum quantity lubrication grinding with nano-particles and recent related patents.

    Science.gov (United States)

    Li, Changhe; Wang, Sheng; Zhang, Qiang; Jia, Dongzhou

    2013-06-01

    In recent years, a large number of patents have been devoted to developing minimum quantity lubrication (MQL) grinding techniques that can significantly improve both environmentally conscious and energy saving and costeffective sustainable grinding fluid alternatives. Among them, one patent is about a supply system for the grinding fluid in nano-particle jet MQL, which produced MQL lubricant by adding solid nano-particles in degradable grinding fluid. The MQL supply device turns the lubricant to the pulse drops with fixed pressure, unchanged pulse frequency and the same drop diameter. The drops will be produced and injected in the grinding zone in the form of jet flow under high pressure gas and air seal. As people become increasingly demanding on our environment, minimum quantity lubrication has been widely used in the grinding and processing. Yet, it presents the defect of insufficient cooling performance, which confines its development. To improve the heat transfer efficiency of MQL, nano-particles of a certain mass fraction can be added in the minimum quantity of lubricant oil, which concomitantly will improve the lubrication effects in the processing. In this study, the grinding experiment corroborated the effect of nano-particles in surface grinding. In addition, compared with other forms of lubrication, the results presented that the grinding force, the friction coefficient and specific grinding energy of MQL grinding have been significantly weakened, while G ratio greatly rose. These are attributed to the friction oil-film with excellent anti-friction and anti-wear performance, which is generated nano-particles at the wheel/workpiece interface. In this research, the cooling performance of nano-particle jet MQL was analyzed. Based on tests and experiments, the surface temperature was assayed from different methods, including flood lubricating oil, dry grinding, MQL grinding and nano-particle jet MQL grinding. Because of the outstanding heat transfer

  18. ANALYSIS OF THE SURFACE PROFILE AND ITS MATERIAL SHARE DURING THE GRINDING INCONEL 718 ALLOY

    Directory of Open Access Journals (Sweden)

    Martin Novák

    2015-05-01

    Full Text Available Grinding is still an important method for surface finishing. At FPTM JEPU research, which deals with this issue is conducted. Experiments are carried out with grinding various materials under different conditions and then selected components of the surface integrity are evaluated. They include roughness Ra, Rm and Rz, Material ratio curve (Abbott Firestone curve and also the obtained roundness. This article deals with grinding nickel Inconel 718 alloy, when selected cutting grinding conditions were used and subsequently the surface profile and the material ratio curve were measured and evaluated.

  19. An experimental assessment on the performance of different lubrication techniques in grinding of Inconel 751

    Directory of Open Access Journals (Sweden)

    A.S.S. Balan

    2016-09-01

    Full Text Available The application of emulsion for combined heat extraction and lubrication requires continuous monitoring of the quality of emulsion to sustain a desired grinding environment; this is applicable to other grinding fluids as well. Thus to sustain a controlled grinding environment, it is necessary to adopt an effectively lubricated wheel-work interface. The current study was undertaken to assess experimentally the ​ effects of different grinding environments such as dry, minimum quantity lubrication (MQL and Cryo-MQL on performance, such as grinding force, temperature, surface roughness and chip morphology on Inconel 751, a higher heat resistance material posing thermal problems and wheel loading. The results show that grinding with the combination of both liquid nitrogen (LN2 and MQL lowers temperature, cutting forces, and surface roughness as compared with MQL and dry grinding. Specific cutting energy is widely used as an inverse measure of process efficiency in machining. It is found from the results that specific cutting energy of Cryo-MQL assisted grinding is 50–65% lower than conventional dry grinding. The grindability of Inconel 751 superalloy can be enhanced with Cryo-MQL condition.

  20. Effect of fiber orientations on surface grinding process of unidirectional C/SiC composites

    Science.gov (United States)

    Zhang, Lifeng; Ren, Chengzu; Ji, Chunhui; Wang, Zhiqiang; Chen, Guang

    2016-03-01

    The machining mechanism of woven ceramic matrix composites is one of the most challenging problems in composite application. To elucidate the grinding mechanism of the woven ceramic matrix composites, a new model material consisting of unidirectional CVI-C/SiC was prepared and ground. The composite was ground in three typical directions and the experimental investigation of the surface grinding process for this composite is described. In addition, the micro structural characteristics and grinding mechanism of the composite were analyzed. The result shows that brittle fracture is the dominant removal mechanism for grinding of the C/SiC composites, and the destroy form of the composites is mainly the syntheses of the matrix cracking, fiber fracture, and interfacial debonding. The grinding force follows the order: Normal > Longitudinal > Transverse, and the surface roughness follows: Longitudinal > Normal > Transverse. The grinding parameters (feed speed, cut depth, grinding speed) have great influence on the grinding force and surface roughness. Based on the findings, the grinding force and surface integrity of the woven ceramic matrix composites can be predicted. Furthermore, it is expected to provide a useful guideline for the design, evaluation and optimal application of the C/SiC composites.

  1. Nano finish grinding of brittle materials using electrolytic in-process dressing (ELID) technique

    Indian Academy of Sciences (India)

    M Rahman; A Senthil Kumar; H S Lim; K Fatima

    2003-10-01

    Recent developments in grinding have opened up new avenues for finishing of hard and brittle materials with nano-surface finish, high tolerance and accuracy. Grinding with superabrasive wheels is an excellent way to produce ultraprecision surface finish. However, superabrasive diamond grits need higher bonding strength while grinding, which metal-bonded grinding wheels can offer. Truing and dressing of the wheels are major problems and they tend to glaze because of wheel loading. When grinding with superabrasive wheels, wheel loading can be avoided by dressing periodically to obtain continuous grinding. Electrolytic inprocess dressing (ELID) is the most suitable process for dressing metal-bonded grinding wheels during the grinding process. Nano-surface finish can be achieved only when chip removal is done at the atomic level. Recent developments of ductile mode machining of hard and brittle materials show that plastically deformed chip removal minimizes the subsurface damage of the workpiece. When chip deformation takes place in the ductile regime, a defect-free nano-surface is possible and it completely eliminates the polishing process. ELID is one of the processes used for atomic level metal removal and nano-surface finish. However, no proper and detailed studies have been carried out to clarify the fundamental characteristics for making this process a robust one. Consequently, an attempt has been made in this study to understand the fundamental characteristics of ELID grinding and their influence on surface finish.

  2. Modeling and Simulation of Process-Machine Interaction in Grinding of Cemented Carbide Indexable Inserts

    Directory of Open Access Journals (Sweden)

    Wei Feng

    2015-01-01

    Full Text Available Interaction of process and machine in grinding of hard and brittle materials such as cemented carbide may cause dynamic instability of the machining process resulting in machining errors and a decrease in productivity. Commonly, the process and machine tools were dealt with separately, which does not take into consideration the mutual interaction between the two subsystems and thus cannot represent the real cutting operations. This paper proposes a method of modeling and simulation to understand well the process-machine interaction in grinding process of cemented carbide indexable inserts. First, a virtual grinding wheel model is built by considering the random nature of abrasive grains and a kinematic-geometrical simulation is adopted to describe the grinding process. Then, a wheel-spindle model is simulated by means of the finite element method to represent the machine structure. The characteristic equation of the closed-loop dynamic grinding system is derived to provide a mathematic description of the process-machine interaction. Furthermore, a coupling simulation of grinding wheel-spindle deformations and grinding process force by combining both the process and machine model is developed to investigate the interaction between process and machine. This paper provides an integrated grinding model combining the machine and process models, which can be used to predict process-machine interactions in grinding process.

  3. Association between anticonvulsant drugs and teeth-grinding in children and adolescents with cerebral palsy.

    Science.gov (United States)

    Ortega, A O L; Dos Santos, M T B R; Mendes, F M; Ciamponi, A L

    2014-09-01

    The relation between teeth-grinding and the use of drugs acting on the central nervous system of cerebral palsy (CP) patients has not yet been described. The aim of this research was to evaluate the presence or absence of teeth-grinding (sleep and/or awake periods) in normal and in CP children and adolescents, as well as the association of teeth-grinding and use of anticonvulsant drugs. The sample consisted of 207 children and adolescents, divided into three groups: G1, individuals with CP who did not take anticonvulsant drugs; G2, individuals with CP administered medications on a regular basis; and CG, normal individuals. Logistic regression analyses were performed to evaluate the association of teeth-grinding with some variables. No significant statistical differences were observed regarding the presence or absence of teeth-grinding when G1 and G2 were compared. However, compared with the CG, a statistically significant difference was determined, with the CG showing fewer children presenting teeth-grinding (P drug therapy, the barbiturate group showed a greater frequency of teeth-grinding. CP children and adolescents show a greater and significant presence of grinding of the teeth compared with normal individuals. Subjects taking barbiturate drugs showed greater presence of teeth-grinding, than those who were taking medications from the other groups of anticonvulsant drugs. © 2014 John Wiley & Sons Ltd.

  4. Modeling and Experimental Investigation of Pressure Field in the Grinding Zone with Nanoparticle Jet of MQL

    Directory of Open Access Journals (Sweden)

    C. H. Li

    2013-01-01

    Full Text Available Solid nano particles were added in minimum quantity lubrication (MQL fluid medium to make nanofluids, that is, after the mixing and atomization of nanoparticle, lubricants and high pressure gas, to inject solid nano particle in the grinding zone with the form of jet flow. The mathematical model of two-phase flow pressure field of grinding zone with nanoparticle jet flow of MQL was established, and the simulation study was conducted. The results show that pressures in the grinding zone increased with the acceleration of grinding wheel, sharply decreased with the increased minimum clearance, and increased with the acceleration of jet flow. At three spraying angles of nozzles, when the nozzle angle was 15°, the pressure of grinding zone along the speed of grinding wheel was larger than the rest two angles. On the experimental platform built by KP-36 precision grinder and nanoparticle jet flow feed way, CY3018 pressure sensor was used to test the regularities of pressure field variations. The impact of the speed of grinding wheel, the gap between workpiece and grinding wheel, jet flow velocity, and spraying angles of nozzles on the pressure field of grinding zone was explored. The experimental result was generally consistent with the theoretical simulation, which verified the accuracy of the theoretical analysis.

  5. Collaboration in electronic resource provision in university libraries: SHEDL, a Scottish case study

    OpenAIRE

    Kidd, T

    2009-01-01

    This case study examines the growth of collaboration among Scottish higher education institutions. Following a summary of the work of the Scottish Confederation of University and Research Libraries (SCURL), more detailed information is provided on collaboration in the fields of acquisition, licensing, selection, and purchasing. Some of the UK background is outlined, relating to NESLi2 in particular, in order to illuminate the options within Scotland. The origins of negotiations on electronic ...

  6. Internet and electronic resources for inflammatory bowel disease: a primer for providers and patients.

    Science.gov (United States)

    Fortinsky, Kyle J; Fournier, Marc R; Benchimol, Eric I

    2012-06-01

    Patients with inflammatory bowel disease (IBD) are increasingly turning to the Internet to research their condition and engage in discourse on their experiences. This has resulted in new dynamics in the relationship between providers and their patients, with misinformation and advertising potentially presenting barriers to the cooperative patient-provider partnership. This article addresses important issues of online IBD-related health information and social media activity, such as quality, reliability, objectivity, and privacy. We reviewed the medical literature on the quality of online information provided to IBD patients, and summarized the most commonly accessed Websites related to IBD. We also assessed the activity on popular social media sites (such as Facebook, Twitter, and YouTube), and evaluated currently available applications for use by IBD patients and providers on mobile phones and tablets. Through our review of the literature and currently available resources, we developed a list of recommended online resources to strengthen patient participation in their care by providing reliable, comprehensive educational material.

  7. Grinding and polishing of conformal windows and domes

    Science.gov (United States)

    Fess, Edward; Ross, James; Matthews, Greg

    2017-05-01

    Conformal optics require special manufacturing techniques to produce them to optical tolerances. In many cases the materials used are very hard optical ceramics that present additional manufacturing challenges due to their hardness and grain structure. OptiPro has developed grinding technologies such as OptiSonic grinding, as well as sub-aperture polishing technologies like UltraForm Finishing (UFF) to manufacture these challenging components. We have also developed a custom computer aided manufacturing (CAM) software package, ProSurf, to generate the complex tool paths for both grinding and polishing processes. One of the main advantages of ProSurf over traditional CAM software packages is that it uses metrology feedback for deterministic corrections. The metrology input can be obtained from OptiPro's 5-axis UltraSurf metrology system, which is capable of measuring these complex shapes to sub-micron accuracies. Through the development of these technologies much work has been performed in creating, measuring and analyzing the alignment fiducials or datum's used to qualify the location of the optical surfaces. Understanding the sensitivity of the optical surface to any datum misalignment is critical to knowing not only where the part is in space, but how good the optical surfaces are to each other. Working with the optical designer to properly tolerance surfaces to these datums is crucial. This paper will present the technologies developed by OptiPro to manufacture conformal windows as well as information related to the optical surfaces sensitivity to datums and how accurately those datums can be measured.

  8. Application of cryogenic grinding to achieve homogenization of transuranic wastes

    Energy Technology Data Exchange (ETDEWEB)

    Atkins, W.H.; Hill, D.D.; Lucero, M.E.; Jaramillo, L.; Martinez, H.E. [and others

    1996-08-01

    This paper describes work done at Los Alamos National Laboratory (LANL) in collaboration with the Department of Energy Rocky Flats Field Office (DOE/RFFO) and with the National Institute of Standards and Technology (NIST), Boulder, Colorado. Researchers on this project have developed a method for cryogenic grinding of mixed wastes to homogenize and, thereby, to acquire a representative sample of the materials. There are approximately 220,000 waste drums owned by the Rocky Flats Environmental Technology Site (RFETS)-50,000 at RFETS and 170,000 at the Idaho National Engineering Laboratory. The cost of sampling the heterogeneous distribution of waste in each drum is prohibitive. In an attempt to produce a homogeneous mixture of waste that would reduce greatly the cost of sampling, researchers at NIST and RFETS are developing a cryogenic grinder. The Los Alamos work herein described addresses the implementation issues of the task. The first issue was to ascertain whether samples of the {open_quotes}small particle{close_quotes} mixtures of materials present in the waste drums at RFETS were representative of actual drum contents. Second, it was necessary to determine at what temperature the grinding operation must be performed in order to minimize or to eliminate the release of volatile organic compounds present in the waste. Last, it was essential to evaluate any effect the liquid cryogen might have on the structural integrity and ventilation capacity of the glovebox system. Results of this study showed that representative samples could be and had been obtained, that some release of organics occurred below freezing because of sublimation, and that operation of the cryogenic grinding equipment inside the glovebox was feasible.

  9. Surface Topography of Fine-grained ZrO2 Ceramic by Two-dimensional Ultrasonic Vibration Grinding

    Institute of Scientific and Technical Information of China (English)

    DING Ailing; WU Yan; LIU Yongjiang

    2011-01-01

    The surface quality of fine-grained ZrO2 engineering ceramic were researched using 270# diamond wheel both with and without work-piece two-dimension ultrasonic vibration grinding(WTDUVG).By AFM images,the surface topography and the micro structure of the two-dimensional ultrasonic vibration grinding ceramics were especially analyzed.The experimental results indicate that the surface roughness is related to grinding vibration mode and the material removal mechanism.Surface quality of WTDUVG is superior to that of conventional grinding,and it is easy for two-dimensional ultrasonic vibration grinding that material removal mechanism is ductile mode grinding.

  10. Modulus Proposal for a Multi Axes Grinding of Sculptured Surfaces

    Science.gov (United States)

    Jandečka, Karel

    2009-11-01

    This paper presents the use of the CAD/CAM system Cimatron for free programming of NC grinding machines. NC technology use, first of all in milling, turning and drilling operations, is widely dispersed at present. Development of these technologies depends to some extent on the cutting tools which are to be produced and sharpened to a high quality. Usable properties of the cutting tools, e.g. the shape accuracy, the quality of function surfaces, etc., are inspired by the production technology used. This technology plays a main role in production and sharpening of powerful and complex shaped cutting tools.

  11. Corrosion of Cast Iron Mill Plates in Wet Grinding

    Directory of Open Access Journals (Sweden)

    Anthony ANDREWS

    2010-12-01

    Full Text Available Corrosion studies were carried out on two different maize grinding plates. Maize was soaked in water for three days and the water decanted and used as electrolyte. Mass loss and pH measurements were carried out every 3 days for 15-day period. Results show that, for each plate, mass loss and pH increased with exposure time. Corrosion rates determined from mass loss data was found to be strongly dependent on pH. The observed behaviour may be explained in terms of the chemical composition and/or microstructures of the plates. Results are briefly discussed in terms of the contribution of corrosion to wear.

  12. Experimental and numerical investigations of hydroerosive grinding for injection components

    Energy Technology Data Exchange (ETDEWEB)

    Iben, Uwe; Weickert, Mathias [Robert Bosch GmbH, Stuttgart (Germany)

    2011-07-01

    Diesel injection injectors are very complicated hydraulic systems which contain among other things small throttles and small sized blow holes in order to inject the fuel precisely into the combustion chamber. Due to the extremely strong exhaust laws, the geometrical forms and tolerances of the hydraulic components have to be maintained. The hydroerosive grinding process (HE process) is used for manufacturing of small holes using in Diesel injection components. A mixture of oil and small sized particles are used to form the final geometrical shapes of the throttles and the blow holes. Simulation models help to understand the underlying physical process and to optimize the manufacturing parameters for an efficient production process. This paper presents an Euler-Euler approach for the numerical simulation of the HE process. It describes a two-phase slurry flow consisting of a liquid and a dispersed solid phase which causes wear at walls of devices. The continuous fluid phase is solved using a finite volume scheme in which the Large Eddy Simulation (LES) model is applied to resolve large-scale turbulent structures. The solid phase is disperse and treated as a second continuum in which drag and lift forces as well as added mass, pressure and history force are taken into account. Considering particle-particle interactions, the granular model from Gidaspow is used for particle volume concentrations over 1%. Investigations of erosion processes proofed that non-spherically shaped particles as well as harder particles increase the wear on devices significantly. Consequently, non-spherical particles are utilized for the hydroerosive grinding. Their steady drag, unsteady drag and lift coefficients, depending on the particle Reynolds number, are determined by a direct numerical simulation via an in-house LES Lattice-Boltzmann solver. This Lattice-Boltzmann method was presented for laminar flows by Hoelzer. In this work, interpolating functions of these coefficients are

  13. Application of electrolytic in-process dressing for high-efficiency grinding of ceramic parts. Research activities 1995--96

    Energy Technology Data Exchange (ETDEWEB)

    Bandyopadhyay, B.P. [Univ. of North Dakota, Grand Forks, ND (United States). Dept. of Mechanical Engineering

    1997-02-01

    The application of Electrolytic In-Process Dressing (ELID) for highly efficient and stable grinding of ceramic parts is discussed. This research was performed at the Institute of Physical and Chemical Research (RIKEN), Tokyo, Japan, June 1995 through August 1995. Experiments were conducted using a vertical machining center. The silicon nitride work material, of Japanese manufacture and supplied in the form of a rectangular block, was clamped to a vice which was firmly fixed on the base of a strain gage dynamometer. The dynamometer was clamped on the machining center table. Reciprocating grinding was performed with a flat-faced diamond grinding wheel. The output from the dynamometer was recorded with a data acquisition system and the normal component of the force was monitored. Experiments were carried out under various cutting conditions, different ELID conditions, and various grinding wheel bonds types. Rough grinding wheels of grit sizes {number_sign}170 and {number_sign}140 were used in the experiments. Compared to conventional grinding, there was a significant reduction in grinding force with ELID grinding. Therefore, ELID grinding can be recommended for high material removal rate grinding, low rigidity machines, and low rigidity workpieces. Compared to normal grinding, a reduction in grinding ratio was observed when ELID grinding was performed. A negative aspect of the process, this reduced G-ratio derives from bond erosion and can be improved somewhat by adjustments in the ELID current. The results of this investigation are discussed in detail in this report.

  14. Approximate creep feed grinding of austempared ductile cast iron; Osutenpa kyujo kokuen chutetsu no kin`i kuripu fido kensaku

    Energy Technology Data Exchange (ETDEWEB)

    Nakamitsu, K.; Shimizu, K. [Oita National College of Technology, Oita (Japan)

    1996-10-01

    Austempered ductile cast iron (ADI) was subjected to approximate creep feed grinding to measure and observe the grinding ratio, hardness of ground surface, grinding resistance, production of burrs, roughness of ground surface, and grinding burn to investigate the best abrasive grains and grinding conditions. The grinding ratio of SiC grains was far better than that of Al2O3 grains, being about 10 times or more. Surface hardness of ADI ground by SiC grains changed little, but that ground by Al2O3 grains increased. As regards grinding resistance, that of Al2O3 grains have less slope and tangential component forces, but that of SiC grains increased with the increase in the ground volume. While burrs produced in grinding with SiC grains are secondary burrs, those produced in grinding with Al2O3 grains are primary burrs. In comparison with the normal grinding, grinding burn was produced on the ground surface, complicate striped patterns and grinding burns were produced by chattering particularly in grinding with Al2O3 grains. 10 refs., 11 figs., 2 tabs.

  15. Granulometric composition study of mineral resources using opto-electronic devices and Elsieve software system

    Directory of Open Access Journals (Sweden)

    Kaminski Stanislaw

    2016-01-01

    Full Text Available The use of mechanical sieves has a great impact on measurement results because occurrence of anisometric particles causes undercounting the average size. Such errors can be avoided by using opto-electronic measuring devices that enable measurement of particles from 10 μm up to a few dozen millimetres in size. The results of measurement of each particle size fraction are summed up proportionally to its weight with the use of Elsieve software system and for every type of material particle-size distribution can be obtained. The software allows further statistical interpretation of the results. Beam of infrared radiation identifies size of particles and counts them precisely. Every particle is represented by an electronic impulse proportional to its size. Measurement of particles in aqueous suspension that replaces the hydrometer method can be carried out by using the IPS L analyser (range from 0.2 to 600 μm. The IPS UA analyser (range from 0.5 to 2000 μm is designed for measurement in the air. An ultrasonic adapter enables performing measurements of moist and aggregated particles from 0.5 to 1000 μm. The construction and software system allow to determine second dimension of the particle, its shape coefficient and specific surface area. The AWK 3D analyser (range from 0.2 to 31.5 mm is devoted to measurement of various powdery materials with subsequent determination of particle shape. The AWK B analyser (range from 1 to 130 mm measures materials of thick granulation and shape of the grains. The presented method of measurement repeatedly accelerates and facilitates study of granulometric composition.

  16. Slag founding: kinetic study and election of a grinding system

    Directory of Open Access Journals (Sweden)

    Salas Vinent, M. E.

    2001-06-01

    Full Text Available Here we offer results obtained in laboratories and industry, concerning the kinetic study of steelfounding in cement manufacture. We choose the most suitable grinding system, valuing also its economical and environmental repercussion. The obtained results indicated that the kinetic method is extremely useful to solve the practical problems in the conception and design of grinding systems, and it is also a speed and the inverted bolting-rell gap almost like a Arrhenius equation.

    Se presentan resultados logrados a escala de laboratorio e industrial referidos al estudio cinético de las escorias de fundición de aceros para la producción de cementos. Se realiza la elección del sistema de molienda más adecuado, valorando además el efecto económico y medio ambiental del mismo. De los resultados obtenidos se concluye que el método cinético resulta de extrema utilidad en la solución de problemas prácticos para la concepción y diseño de sistemas de molienda, amén de que en el plano teórico resulta una novedad la correlación encontrada entre la constante de velocidad de molienda y el inverso de la abertura del tamiz de modo similar a la ecuación de Arrhenius.

  17. Effects of grinding processes on enzymatic degradation of wheat straw.

    Science.gov (United States)

    Silva, Gabriela Ghizzi D; Couturier, Marie; Berrin, Jean-Guy; Buléon, Alain; Rouau, Xavier

    2012-01-01

    The effectiveness of wheat straw fine to ultra-fine grindings at pilot scale was studied. The produced powders were characterised by their particle-size distribution (laser diffraction), crystallinity (WAXS) and enzymatic degradability (Trichoderma reesei enzymatic cocktail). A large range of wheat-straw powders was produced: from coarse (median particle size ∼800 μm) to fine particles (∼50 μm) using sieve-based grindings, then ultra-fine particles ∼20 μm by jet milling and ∼10 μm by ball milling. The wheat straw degradability was enhanced by the decrease of particle size until a limit: ∼100 μm, up to 36% total carbohydrate and 40% glucose hydrolysis yields. Ball milling samples overcame this limit up to 46% total carbohydrate and 72% glucose yields as a consequence of cellulose crystallinity reduction (from 22% to 13%). Ball milling appeared to be an effective pretreatment with similar glucose yield and superior carbohydrate yield compared to steam explosion pretreatment.

  18. Analysis on Large Deformation Compensation Method for Grinding Machine

    Directory of Open Access Journals (Sweden)

    Wang Ya-jie

    2013-08-01

    Full Text Available The positioning accuracy of computer numerical control machines tools and manufacturing systems is affected by structural deformations, especially for large sized systems. Structural deformations of the machine body are difficult to model and to predict. Researchs for the direct measurement of the amount of deformation and its compensation are farly limited in domestic and overseas,not involved to calculate the amount of deformation compensation. A new method to compensate large deformation caused by self-weight was presented in the paper. First of all, the compensation method is summarized; Then,static force analysis was taken on the large grinding machine through APDL(ANSYS Parameter Design Language. It could automatic extract results and form data files, getting the N points displacement in the working stroke of mechanical arm. Then, the mathematical model and corresponding flat rectangular function were established. The conclusion that the new compensation method is feasible was obtained through the analysis of displacement of N points. Finally, the MATLAB as a tool is used to calculate compensate amount and the accuracy of the proposed method is proved. Practice shows that the error caused by large deformatiion compensation method can meet the requirements of grinding.  

  19. ARE THERE SIGNIFICANT DIFFERENCES BETWEEN DIRECT AND REVERSE GRINDING CIRCUITS?

    Directory of Open Access Journals (Sweden)

    Douglas Batista Mazzinghy

    2014-12-01

    Full Text Available The mining industry is famous for many paradigms regarding different flowsheet designs and the use of new technologies and equipment. In this context, a question often performed to process engineers is: what grinding circuit is more efficient, the direct or the reverse? A precise answer could only be given by experimental data and simulations. Simulations were performed using ModSimTM software considering parameters obtained by batch mill tests of an iron ore sample. The simulations, preliminarily, indicated no significant differences between the two circuit configurations for the sample tested. Subsequently, tests were conducted on a pilot scale with detailed measurement of all the variables necessary for a correct interpretation of the differences between the direct and reverse circuits. The test results confirmed the prediction obtained by simulation. This work provides the basis to test other ores and to understanding better the real differences between grinding circuit configurations. Thus, it is expected that some myths of the mineral industry, with respect to flowsheet choices, are overcome.

  20. Effects of imbalance and geometric error on precision grinding machines

    Energy Technology Data Exchange (ETDEWEB)

    Bibler, J.E.

    1997-06-01

    To study balancing in grinding, a simple mechanical system was examined. It was essential to study such a well-defined system, as opposed to a large, complex system such as a machining center. The use of a compact, well-defined system enabled easy quantification of the imbalance force input, its phase angle to any geometric decentering, and good understanding of the machine mode shapes. It is important to understand a simple system such as the one I examined given that imbalance is so intimately coupled to machine dynamics. It is possible to extend the results presented here to industrial machines, although that is not part of this work. In addition to the empirical testing, a simple mechanical system to look at how mode shapes, balance, and geometric error interplay to yield spindle error motion was modelled. The results of this model will be presented along with the results from a more global grinding model. The global model, presented at ASPE in November 1996, allows one to examine the effects of changing global machine parameters like stiffness and damping. This geometrically abstract, one-dimensional model will be presented to demonstrate the usefulness of an abstract approach for first-order understanding but it will not be the main focus of this thesis. 19 refs., 36 figs., 10 tables.

  1. 试论图书馆电子资源与纸本资源的协调发展%The coordinated development of library electronic resources and paper resources

    Institute of Scientific and Technical Information of China (English)

    冯雷

    2012-01-01

      纸本资源和电子资源属于公共图书馆文献资源中两个非常重要的资源类型,纸本资源和电子资源的协调发展在图书馆的可持续发展过程中起着非常重要的作用。本文对如何实现图书馆电子资源和纸本资源之间的协调发展进行了探讨,希望能够为图书馆文献资源的管理提供一些参考。%  The paper and electronic resources are two very important types of literature resources of public libraries, the coordinated development of the paper and electronic resources play a very important role in the sustainable development process of the library. This article discusses how to realize the coordinated development of library electronic resources and paper resources, hope to provide some reference for library literature resource management.

  2. An efficient, robust, and inexpensive grinding device for herbal samples like Cinchona bark

    DEFF Research Database (Denmark)

    Hansen, Steen Honoré; Holmfred, Else Skovgaard; Cornett, Claus;

    2015-01-01

    An effective, robust, and inexpensive grinding device for the grinding of herb samples like bark and roots was developed by rebuilding a commercially available coffee grinder. The grinder was constructed to be able to provide various particle sizes, to be easy to clean, and to have a minimum of d...

  3. Electrochemical aspects of grinding media-mineral interaction on sulphide flotation

    OpenAIRE

    Rao, Yelloji MK; Natarajan, KA

    1988-01-01

    Galvanic interaction between electrically conducting minerals may affect the mineral surface and influence their flotabilities. The metallographic examinations as well as hardness measurements have been made with grinding media. Rest potential, combination potential, galvanic current and polarization studies were made to understand the probable electrochemical interaction between grinding media and chalcopyrite. The galvanic contact lowered the flotability of chalcopyrite. AES and ESCA indica...

  4. Recognition of diamond grains on surface of fine diamond grinding wheel

    Institute of Scientific and Technical Information of China (English)

    Fengwei HUO; Zhuji JIN; Renke KANG; Dongming GUO; Chun YANG

    2008-01-01

    The accurate evaluation of grinding wheel sur-face topography, which is necessary for the investigation of the grinding principle, optimism, modeling, and simu-lation of a grinding process, significantly depends on the accurate recognition of abrasive grains from the measured wheel surface. A detailed analysis of the grain size distri-bution characteristics and grain profile wavelength of the fine diamond grinding wheel used for ultra-precision grinding is presented. The requirements of the spatial sampling interval and sampling area for instruments to measure the surface topography of a diamond grinding wheel are discussed. To recognize diamond grains, digital filtering is used to eliminate the high frequency disturb-ance from the measured 3D digital surface of the grinding wheel, the geometric features of diamond grains are then extracted from the filtered 3D digital surface, and a method based on the grain profile frequency characteris-tics, diamond grain curvature, and distance between two adjacent diamond grains is proposed. A 3D surface pro-filer based on scanning white light interferometry is used to measure the 3D surface topography of a #3000 mesh resin bonded diamond grinding wheel, and the diamond grains are then recognized from the 3D digital surface. The experimental result shows that the proposed method is reasonable and effective.

  5. Capturing action of cooling lubricants in grinding and evaluation of its effectiveness

    Science.gov (United States)

    Tyukhta, A. V.; Khandozhko, A. V.; Vasilenko, Yu V.

    2016-04-01

    Methods of coolant supply are considered to be aiming at capturing and neutralization of the flare of grinding waste and noxious coolant fumes during flat grinding with a wheel periphery. Study and evaluation of the new coolant functional property - capturing - are presented.

  6. THERMAL AND PHYSICAL FEATURES OF MAGNETIC AND ELECTRIC GRINDING PROCESS OF GAS AND THERMAL PROTECTIVE COATINGS

    Directory of Open Access Journals (Sweden)

    N. V. Spiridonov

    2008-01-01

    Full Text Available The paper reveals thermal zones of magnetic and electric grinding process. The influence of electric and physical parameters of magnetic and electric grinding on temperature in the zone of gas and thermal protective coatings has been established in the paper.

  7. On the Development of Electronic Resources and Paper Resources%关于电子资源与纸本资源协调发展的思考和建议

    Institute of Scientific and Technical Information of China (English)

    王军武

    2012-01-01

    In recent years, a large number of electronic resources was introduced to the libraries, which has become an im- portant component of library resource system. However, there are also a lot of hot debates about the following issues, such as how to build a traditional paper resources, how to deal with the relationship between paper resources and electronic resources, how to build a library resources development system, etc. These problems also confused many librarians who are building resources in the library. With the combination with the opinions from some experts, research scholars, the paper proposed some guiding principles to deal with the relationship between electronic resources and paper resources. Taking all the aspects into consideration, such as the concepts of the library, the funding of the resources, the policies and structure of the library, cooperative development, the paper also proposes some measures for the development of electronic resources and paper resources.%在复合图书馆环境下,如何协调发展电子资源与纸本资源是图书馆界专家、学者研究和探讨的热点问题,也是许多图书馆工作者在文献资源建设实践中十分困惑的问题。文章结合有关专家、学者的研究成果及图书馆的相关案例,概述了电子资源与纸本资源协调发展应遵循的指导性原则,并从馆藏理念、经费投入、馆藏政策、馆藏结构、合作发展、服务利用等几个方面提出了协调发展电子资源与纸本资源的若干举措。

  8. Investigation of the formation process of two piracetam cocrystals during grinding

    DEFF Research Database (Denmark)

    Rehder, Sönke; Klukkert, Marten; Löbmann, Korbinian;

    2011-01-01

    Cocrystal formation rates during dry grinding and liquid-assisted grinding were investigated by X-ray powder diffractometry and Raman spectroscopy. Two polymorphic forms of piracetam were used to prepare known piracetam cocrystals as model substances, i.e.,piracetam-citric acid and piracetam......-tartaric acid cocrystals. Raman spectroscopy in combination with principal component analysis was used to visualize the cocrystal formation pathways. During dry grinding, cocrystal formation appeared to progress via an amorphous intermediate stage, which was more evident for the piracetam-citric acid than...... for the piracetam-tartaric acid cocrystal. It was shown that liquid-assisted grinding led to faster cocrystal formation than dry grinding, which may be explained by the higher transformation rate due to the presence of liquid. The cocrystal formation rate did not depend on the applied polymorphic form...

  9. Measurement of Force Components and Ra Surface Roughness Parameter During Grinding Titanium Alloy

    Directory of Open Access Journals (Sweden)

    Grdulska A.

    2014-10-01

    Full Text Available The paper deals with the measurements of selected parameters during grinding process of aerospace industry alloy. Grinding is one of the most important methods of shaping machine elements. As a result of grinding with high dimensional and shape accuracy as well as with the expected parameters describing the state of the surface layer (SL should be obtained. Grinding difficult to machine materials used in the aerospace industry is an issue currently being examined by various research centres. An excellent example is the analysis of the grinding process of titanium alloys, as these materials have very poor machinability due to the tendency to adherence to abrasive materials, low thermal conductivity, high strength and compliance at elevated temperatures, which may adversely impact on the quality of SL. A number of factors influence on shaping SL. Worth mentioning are mechanical and thermal phenomena, as well as the type of cutting fluid and abrasive materials

  10. Investigation of the formation process of two piracetam cocrystals during grinding

    DEFF Research Database (Denmark)

    Rehder, Sönke; Klukkert, Marten; Löbmann, Korbinian

    2011-01-01

    Cocrystal formation rates during dry grinding and liquid-assisted grinding were investigated by X-ray powder diffractometry and Raman spectroscopy. Two polymorphic forms of piracetam were used to prepare known piracetam cocrystals as model substances, i.e.,piracetam-citric acid and piracetam......-tartaric acid cocrystals. Raman spectroscopy in combination with principal component analysis was used to visualize the cocrystal formation pathways. During dry grinding, cocrystal formation appeared to progress via an amorphous intermediate stage, which was more evident for the piracetam-citric acid than...... for the piracetam-tartaric acid cocrystal. It was shown that liquid-assisted grinding led to faster cocrystal formation than dry grinding, which may be explained by the higher transformation rate due to the presence of liquid. The cocrystal formation rate did not depend on the applied polymorphic form...

  11. Investigation of the Formation Process of Two Piracetam Cocrystals during Grinding

    Directory of Open Access Journals (Sweden)

    Keith Gordon

    2011-10-01

    Full Text Available Cocrystal formation rates during dry grinding and liquid-assisted grinding were investigated by X-ray powder diffractometry and Raman spectroscopy. Two polymorphic forms of piracetam were used to prepare known piracetam cocrystals as model substances, i.e.,piracetam-citric acid and piracetam-tartaric acid cocrystals. Raman spectroscopy in combination with principal component analysis was used to visualize the cocrystal formation pathways. During dry grinding, cocrystal formation appeared to progress via an amorphous intermediate stage, which was more evident for the piracetam-citric acid than for the piracetam-tartaric acid cocrystal. It was shown that liquid-assisted grinding led to faster cocrystal formation than dry grinding, which may be explained by the higher transformation rate due to the presence of liquid. The cocrystal formation rate did not depend on the applied polymorphic form of the piracetam and no polymorphic cocrystals were obtained.

  12. Investigation of the Formation Process of Two Piracetam Cocrystals during Grinding

    Science.gov (United States)

    Rehder, Sönke; Klukkert, Marten; Löbmann, Korbinian A. M.; Strachan, Clare J.; Sakmann, Albrecht; Gordon, Keith; Rades, Thomas; Leopold, Claudia S.

    2011-01-01

    Cocrystal formation rates during dry grinding and liquid-assisted grinding were investigated by X-ray powder diffractometry and Raman spectroscopy. Two polymorphic forms of piracetam were used to prepare known piracetam cocrystals as model substances, i.e., piracetam-citric acid and piracetam-tartaric acid cocrystals. Raman spectroscopy in combination with principal component analysis was used to visualize the cocrystal formation pathways. During dry grinding, cocrystal formation appeared to progress via an amorphous intermediate stage, which was more evident for the piracetam-citric acid than for the piracetam-tartaric acid cocrystal. It was shown that liquid-assisted grinding led to faster cocrystal formation than dry grinding, which may be explained by the higher transformation rate due to the presence of liquid. The cocrystal formation rate did not depend on the applied polymorphic form of the piracetam and no polymorphic cocrystals were obtained. PMID:24309304

  13. Green Supply Chain Collaboration for Fashionable Consumer Electronics Products under Third-Party Power Intervention—A Resource Dependence Perspective

    Directory of Open Access Journals (Sweden)

    Jiuh-Biing Sheu

    2014-05-01

    Full Text Available Under third-party power intervention (TPPI, which increases uncertainty in task environments, complex channel power interplays and restructuring are indispensable among green supply chain members as they move toward sustainable collaborative relationships for increased viability and competitive advantage. From the resource dependence perspective, this work presents a novel conceptual model to investigate the influence of political and social power on channel power restructuring and induced green supply chain collaboration in brander-retailer bidirectional green supply chains of fashionable consumer electronics products (FCEPs. An FCEP refers to the consumer electronics product (e.g., personal computers, mobile phones, computer notebooks, and game consoles with the features of a well-known brand associated, a short product lifecycle, timely and fashionable design fit for market trends, and quick responsiveness to the variations of market demands. The proposed model is tested empirically using questionnaire data obtained from retailers in the FCEP brander-retailer distribution channels. Analytical results reveal that as an extension of political and social power, TPPI positively affects the reciprocal interdependence of dyadic members and reduces power asymmetry, thereby enhancing the collaborative relationship of dyadic members and leading to improved green supply chain performance. Therein, reciprocal interdependence underlying collaborative relationship is the key to reducing the external environmental uncertainties in the TPPI context.

  14. Optimization of the dressing parameters in cylindrical grinding based on a generalized utility function

    Science.gov (United States)

    Aleksandrova, Irina

    2016-01-01

    The existing studies, concerning the dressing process, focus on the major influence of the dressing conditions on the grinding response variables. However, the choice of the dressing conditions is often made, based on the experience of the qualified staff or using data from reference books. The optimal dressing parameters, which are only valid for the particular methods and dressing and grinding conditions, are also used. The paper presents a methodology for optimization of the dressing parameters in cylindrical grinding. The generalized utility function has been chosen as an optimization parameter. It is a complex indicator determining the economic, dynamic and manufacturing characteristics of the grinding process. The developed methodology is implemented for the dressing of aluminium oxide grinding wheels by using experimental diamond roller dressers with different grit sizes made of medium- and high-strength synthetic diamonds type ??32 and ??80. To solve the optimization problem, a model of the generalized utility function is created which reflects the complex impact of dressing parameters. The model is built based on the results from the conducted complex study and modeling of the grinding wheel lifetime, cutting ability, production rate and cutting forces during grinding. They are closely related to the dressing conditions (dressing speed ratio, radial in-feed of the diamond roller dresser and dress-out time), the diamond roller dresser grit size/grinding wheel grit size ratio, the type of synthetic diamonds and the direction of dressing. Some dressing parameters are determined for which the generalized utility function has a maximum and which guarantee an optimum combination of the following: the lifetime and cutting ability of the abrasive wheels, the tangential cutting force magnitude and the production rate of the grinding process. The results obtained prove the possibility of control and optimization of grinding by selecting particular dressing

  15. Innovative grinding wheel design for cost-effective machining of advanced ceramics. Phase I, final report

    Energy Technology Data Exchange (ETDEWEB)

    Licht, R.H.; Ramanath, S.; Simpson, M.; Lilley, E.

    1996-02-01

    Norton Company successfully completed the 16-month Phase I technical effort to define requirements, design, develop, and evaluate a next-generation grinding wheel for cost-effective cylindrical grinding of advanced ceramics. This program was a cooperative effort involving three Norton groups representing a superabrasive grinding wheel manufacturer, a diamond film manufacturing division and a ceramic research center. The program was divided into two technical tasks, Task 1, Analysis of Required Grinding Wheel Characteristics, and Task 2, Design and Prototype Development. In Task 1 we performed a parallel path approach with Superabrasive metal-bond development and the higher technical risk, CVD diamond wheel development. For the Superabrasive approach, Task 1 included bond wear and strength tests to engineer bond-wear characteristics. This task culminated in a small-wheel screening test plunge grinding sialon disks. In Task 2, an improved Superabrasive metal-bond specification for low-cost machining of ceramics in external cylindrical grinding mode was identified. The experimental wheel successfully ground three types of advanced ceramics without the need for wheel dressing. The spindle power consumed by this wheel during test grinding of NC-520 sialon is as much as to 30% lower compared to a standard resin bonded wheel with 100 diamond concentration. The wheel wear with this improved metal bond was an order of magnitude lower than the resin-bonded wheel, which would significantly reduce ceramic grinding costs through fewer wheel changes for retruing and replacements. Evaluation of ceramic specimens from both Tasks 1 and 2 tests for all three ceramic materials did not show evidence of unusual grinding damage. The novel CVD-diamond-wheel approach was incorporated in this program as part of Task 1. The important factors affecting the grinding performance of diamond wheels made by CVD coating preforms were determined.

  16. Electronic medical record data to identify variables associated with a fibromyalgia diagnosis: importance of health care resource utilization

    Directory of Open Access Journals (Sweden)

    Masters ET

    2015-03-01

    Full Text Available Elizabeth T Masters,1 Jack Mardekian,1 Birol Emir,1 Andrew Clair,1 Max Kuhn,2 Stuart L Silverman,31Pfizer, Inc., New York, NY, 2Pfizer, Inc., Groton, CT, 3Cedars-Sinai Medical Center, Los Angeles, CA, USABackground: Diagnosis of fibromyalgia (FM is often challenging. Identifying factors associated with an FM diagnosis may guide health care providers in implementing appropriate diagnostic and management strategies.Methods: This retrospective study used the de-identified Humedica electronic medical record (EMR database to identify variables associated with an FM diagnosis. Cases (n=4,296 were subjects ≥18 years old with ≥2 International Classification of Diseases, Ninth Revision (ICD-9 codes for FM (729.1 ≥30 days apart during 2012, associated with an integrated delivery network, with ≥1 encounter with a health care provider in 2011 and 2012. Controls without FM (no-FM; n=583,665 did not have the ICD-9 codes for FM. Demographic, clinical, and health care resource utilization variables were extracted from structured EMR data. Univariate analysis identified variables showing significant differences between the cohorts based on odds ratios (ORs.Results: Consistent with FM epidemiology, FM subjects were predominantly female (78.7% vs 64.5%; P<0.0001 and slightly older (mean age 53.3 vs 52.7 years; P=0.0318. Relative to the no-FM cohort, the FM cohort was characterized by a higher prevalence of nearly all evaluated comorbidities; the ORs suggested a higher likelihood of an FM diagnosis (P<0.0001, especially for musculoskeletal and neuropathic pain conditions (OR 3.1 for each condition. Variables potentially associated with an FM diagnosis included higher levels of use of specific health care resources including emergency-room visits, outpatient visits, hospitalizations, and medications. Units used per subject for emergency-room visits, outpatient visits, hospitalizations, and medications were also significantly higher in the FM cohort (P<0

  17. Comparison of tungsten carbide and stainless steel ball bearings for grinding single maize kernels in a reciprocating grinder

    Science.gov (United States)

    Reciprocating grinders can grind single maize kernels by shaking the kernel in a vial with a ball bearing. This process results in a grind quality that is not satisfactory for many experiments. Tungesten carbide ball bearings are nearly twice as dense as steel, so we compared their grinding performa...

  18. Survey on User Satisfaction of Electronic Resources in University Libraries%高校图书馆电子资源用户满意度调查

    Institute of Scientific and Technical Information of China (English)

    陈姚竹; 马东

    2011-01-01

    通过分析影响用户对图书馆电子资源利用的因素,以美国顾客满意度指数模型为基础,提出关于各个因素的测量指标,对高校图书馆电子资源用户满意度进行测量。%Through analyzing the influencing factors on utilizing library electronic resources, based on the model of American customer satisfaction index, the paper puts forward corresponding measurement indexes, and then measures the user satisfaction on electronic resources of university library

  19. Nano surface generation of grinding process using carbon nano tubes

    Indian Academy of Sciences (India)

    S Prabhu; B K Vinayagam

    2010-12-01

    Nano surface finish has become an important parameter in the semiconductor, optical, electrical and mechanical industries. The materials used in these industries are classified as difficult to machine materials such as ceramics, glasses and silicon wafers. Machining of these materials up to nano accuracy is a great challenge in the manufacturing industry. Finishing of micro components such as micro-moulds, micro-lenses and micro-holes need different processing techniques. Conventional finishing methods used so far become almost impossible or cumbersome. In this paper, a nano material especially multi wall carbon nano tube is used in the machining process like grinding to improve the surface characteristics from micro to nano level.

  20. Function of grinding fly ash in production of aluminum foam

    Institute of Scientific and Technical Information of China (English)

    WANG Yong; YAO Guang-chun; LI Bing

    2006-01-01

    The fly ash was added to melt to increase the melt viscosity. The main components are quartz and mullite in the fly ash,therefore it's a kind of hardness ceramic particles. After grinding for 10 h, the spherical particles increase and new surface is produced which will improve their performance. The cell wall was observed by SEM, many fly ash particles are in the wall. These particles tend to increase the molten aluminum surface viscosity, postpone the exhaust course, sustain the liquid within the film and delay the onset of rupture. Finally, the aluminum foam with uniform cell structure can be obtained. The density is about 0.4 g/cm3,porosity is in the range of 85%-90% and the aperture is 4-7 mm.

  1. Intra-pulp temperature increase of equine cheek teeth during treatment with motorized grinding systems: influence of grinding head position and rotational speed

    Science.gov (United States)

    2014-01-01

    Background In equine practice, teeth corrections by means of motorized grinding systems are standard procedure. The heat resulting from that treatment may cause irreparable damage to the dental pulp. It has been shown that a 5.5°C temperature rise may cause severe destruction in pulp cells. Hence, the capability to continuously form secondary dentine is lost, and may lead, due to equine-typical occlusal tooth abrasion, to an opening of the pulp cavity. To obtain reliable data on the intra-pulp increase in temperature during corrective treatments, equine cheek teeth (CT) were modified in a way (occlusal surface smoothed, apical parts detached, pulp horns standardized) that had been qualified in own former published studies. All parameters influencing the grinding process were standardized (force applied, initial temperatures, dimensions of pulp horns, positioning of grinding disk, rotational speed). During grinding experiments, imitating real dental treatments, the time span for an intra-pulp temperature increase of 5.5°C was determined. Results The minimum time recorded for an intra-pulp temperature increase of 5.5°C was 38 s in mandibular CT (buccal grinding, 12,000 rpm) and 70 s in maxillary CT (flat occlusal grinding, 12,000 rpm). The data obtained showed that doubling the rotational speed of the disk results in halving the time span after which the critical intra-pulp temperature increase in maxillary CT is reached. For mandibular CT, the time span even drops by two thirds. Conclusion The use of standardized hypsodont CT enabled comparative studies of intra-pulp heating during the grinding of occlusal tooth surfaces using different tools and techniques. The anatomical structure of the natural vital hypsodont tooth must be kept in mind, so that the findings of this study do not create a deceptive sense of security with regard to the time-dependent heating of the native pulp. PMID:24559121

  2. Development of an electronic medical record based alert for risk of HIV treatment failure in a low-resource setting.

    Directory of Open Access Journals (Sweden)

    Nancy Puttkammer

    Full Text Available BACKGROUND: The adoption of electronic medical record systems in resource-limited settings can help clinicians monitor patients' adherence to HIV antiretroviral therapy (ART and identify patients at risk of future ART failure, allowing resources to be targeted to those most at risk. METHODS: Among adult patients enrolled on ART from 2005-2013 at two large, public-sector hospitals in Haiti, ART failure was assessed after 6-12 months on treatment, based on the World Health Organization's immunologic and clinical criteria. We identified models for predicting ART failure based on ART adherence measures and other patient characteristics. We assessed performance of candidate models using area under the receiver operating curve, and validated results using a randomly-split data sample. The selected prediction model was used to generate a risk score, and its ability to differentiate ART failure risk over a 42-month follow-up period was tested using stratified Kaplan Meier survival curves. RESULTS: Among 923 patients with CD4 results available during the period 6-12 months after ART initiation, 196 (21.2% met ART failure criteria. The pharmacy-based proportion of days covered (PDC measure performed best among five possible ART adherence measures at predicting ART failure. Average PDC during the first 6 months on ART was 79.0% among cases of ART failure and 88.6% among cases of non-failure (p<0.01. When additional information including sex, baseline CD4, and duration of enrollment in HIV care prior to ART initiation were added to PDC, the risk score differentiated between those who did and did not meet failure criteria over 42 months following ART initiation. CONCLUSIONS: Pharmacy data are most useful for new ART adherence alerts within iSanté. Such alerts offer potential to help clinicians identify patients at high risk of ART failure so that they can be targeted with adherence support interventions, before ART failure occurs.

  3. Controlled wear of vitrified abrasive materials for precision grinding applications

    Indian Academy of Sciences (India)

    M J Jackson; B Mills; M P Hitchiner

    2003-10-01

    The study of bonding hard materials such as aluminium oxide and cubic boron nitride (BN) and the nature of interfacial cohesion between these materials and glass is very important from the perspective of high precision grinding. Vitrified grinding wheels are typically used to remove large volumes of metal and to produce components with very high tolerances. It is expected that the same grinding wheel is used for both rough and finish machining operations. Therefore, the grinding wheel, and in particular its bonding system, is expected to react differently to a variety of machining operations. In order to maintain the integrity of the grinding wheel, the bonding system that is used to hold abrasive grains in place reacts differently to forces that are placed on individual bonding bridges. This paper examines the role of vitrification heat treatment on the development of strength between abrasive grains and bonding bridges, and the nature of fracture and wear in vitrified grinding wheels that are used for precision grinding applications.

  4. Reseach on Mill-grinding Experiment of Grinding Wheel with Phyllotactic Pattern%磨粒族叶序排布砂轮的铣磨实验研究

    Institute of Scientific and Technical Information of China (English)

    王军; 赵良兵; 赵成义; 吕玉山

    2013-01-01

    In order to realize the ordering of the grinding wheel abrasive surface assignment, this paper combined with phyllotaxis theory and grinding mechanism, and manufactured phyllotactic pattern grinding wheel by UV lithography method and electroplating technology. The mill-grinding experiment results show that; the grinding performance of phyllotactic pattern grinding wheel is superior to what of disordered arrangement grinding wheel.%为了实现砂轮表面磨料排布的有序化,本文将仿生学叶序理论与磨削机理相结合,利用光刻技术和复合电镀技术制备出了磨粒族叶序排布砂轮.铣磨实验结果表明:磨粒族叶序排布砂轮的磨削性能优于普通无序排布砂轮.

  5. Optimization of Metal Removal Rateon Cylindrical Grinding For Is 319 Brass Using Taguchi Method

    Directory of Open Access Journals (Sweden)

    Gaurav Upadhyay

    2015-06-01

    Full Text Available Cylindrical grinding is one of the most important metal cutting processes used extensively in the Metal finishing operations. Metal removal rate and surface finish are the important output responses in the production with respect to quantity and quality respectively. The objective of this paper is to arrive at the optimal grinding conditions that will maximize metal removal rate when grinding IS 319 brass. Empirical models were developed using design of experiments by Taguchi L9 Orthogonal Array and the adequacy of the developed model is tested with ANOVA.

  6. Affecting mechanism of grinding aid during ultrafine grinding%超细粉碎过程助磨剂的作用机理

    Institute of Scientific and Technical Information of China (English)

    杨华明; 邱冠周

    2000-01-01

    通过粉体ζ-电位、矿浆粘度测定及光电子能谱(XPS)和分散率分析,研究了搅拌磨超细粉碎滑石粉过程中助磨剂的助磨行为.分析了六偏磷酸钠与滑石粉的表面作用及吸附特性,提出了助磨剂在超细粉碎过程中的吸附模型.此外,探讨了助磨剂对超细粉碎行为的影响.研究结果表明,助磨剂通过与滑石粉的吸附作用,降低了矿浆粘度,从而提高了超细粉碎的效率.%The aiding behavior of hexametaphosphate(hexa) during uhrafine grinding of talc with stirred mill is studiedthrough analysis of ζ-potenfial,pulp viscosity,XPS and scattering rate in the paper. The surfacial effect and adsorptioncharacteristics of Hexa on talc particles are analysed. A typical model of grinding aid during ultrafine grinding is given.Effect of Hexa on ultrafine grinding behavior is also discussed. The results show that it is the adsorption of Hexa and re-ducing pulp viscosity that improve the grinding efficiency.

  7. The BRIGHTEN Program: Implementation and Evaluation of a Program to Bridge Resources of an Interdisciplinary Geriatric Health Team via Electronic Networking

    Science.gov (United States)

    Emery, Erin E.; Lapidos, Stan; Eisenstein, Amy R.; Ivan, Iulia I.; Golden, Robyn L.

    2012-01-01

    Purpose: To demonstrate the feasibility of the BRIGHTEN Program (Bridging Resources of an Interdisciplinary Geriatric Health Team via Electronic Networking), an interdisciplinary team intervention for assessing and treating older adults for depression in outpatient primary and specialty medical clinics. The BRIGHTEN team collaborates "virtually"…

  8. The module of methodical support in system of electronic educational resources as the innovative element of the modern maintenance of formation

    Directory of Open Access Journals (Sweden)

    Ольга Николаевна Крылова

    2009-06-01

    Full Text Available The article introduces some results of research, which were devoted to evaluation of tearches' mobility to introduce innovations in the contents of education. The author considers innovative potential of modules of the methodical support for system of electronic educational resources.

  9. Charting a Course through CORAL: Texas A&M University Libraries' Experience Implementing an Open-Source Electronic Resources Management System

    Science.gov (United States)

    Hartnett, Eric; Beh, Eugenia; Resnick, Taryn; Ugaz, Ana; Tabacaru, Simona

    2013-01-01

    In 2010, after two previous unsuccessful attempts at electronic resources management system (ERMS) implementation, Texas A&M University (TAMU) Libraries set out once again to find an ERMS that would fit its needs. After surveying the field, TAMU Libraries selected the University of Notre Dame Hesburgh Libraries-developed, open-source ERMS,…

  10. The BRIGHTEN Program: Implementation and Evaluation of a Program to Bridge Resources of an Interdisciplinary Geriatric Health Team via Electronic Networking

    Science.gov (United States)

    Emery, Erin E.; Lapidos, Stan; Eisenstein, Amy R.; Ivan, Iulia I.; Golden, Robyn L.

    2012-01-01

    Purpose: To demonstrate the feasibility of the BRIGHTEN Program (Bridging Resources of an Interdisciplinary Geriatric Health Team via Electronic Networking), an interdisciplinary team intervention for assessing and treating older adults for depression in outpatient primary and specialty medical clinics. The BRIGHTEN team collaborates "virtually"…

  11. Electronic Information Resources (EIR Adoption in Private University Libraries: The Moderating Effect of Productivity and Relative Advantage on Perceived Usefulness

    Directory of Open Access Journals (Sweden)

    Izuagbe, Roland

    2016-03-01

    Full Text Available The study tested a hybrid model with constructs drawn from the Technology Acceptance Model (TAM and Diffusion of Innovation (DOI theory in order to examine the moderating effect of productivity and relative advantage (RA on perceived usefulness (PU vis-à-vis electronic information resources (EIR adoption in private university libraries in Ogun and Osun States of Nigeria. The descriptive research design was adopted in the study. The population consisted of 61 (55.0% librarians and 50 (45.0% library officers (totaling 116—100% in Babcock University, Bells University, Covenant University, Bowen University, Oduduwa University, and Redeemer's University. Purposive sampling procedure was adopted after which total enumeration was used since the total population is small. The questionnaire was used for data collection. Of the 116 copies of the questionnaire administered, 111 (95.7% were found usable. The instrument was structured based on a 4-point Likert agreement scale of Strongly Agree, Agree, Disagree, and Strongly Disagree. Data were analyzed using descriptive statistics like tables of frequency counts and percentage. The findings revealed that productivity and relative advantage are significant moderators of perceived usefulness of EIR adoption in private university libraries in Ogun and Osun States, Nigeria.

  12. Influence of grinding on service properties of VT-22 powder applied in additive technologies

    Science.gov (United States)

    Zakharov, M. N.; Rybalko, O. F.; Romanova, O. V.; Gelchinskiy, B. R.; Il’inykh, S. A.; Krashaninin, V. A.

    2017-01-01

    Powder of titanium alloy (VT-22) produced by plasma-spraying was subjected to grinding to obtain powder with size less 100 microns. These powders were sprayed by plasma unit using two types of gases, namely, air and air with methane (spraying in water and sputtering of coating on steel support). Influence of grinding time on yield of powder of required fraction was studied. Morphology and phase composition of the grinded powder and plasma sprayed one were under investigation. In the result of experiments, it appears that the grinding time genuinely influences the chemical and phase compositions, but there is no effect on physical-processing properties. For powders after plasma spraying some changes of non-metal elements content were detected by chemical analysis. Using gaseous mixture of air and methane in plasma spraying unit leads to formation of a new phase in the powder according X-ray diffraction data.

  13. Force-controlled analysis tool for optimization of precision CNC grinding processes

    Science.gov (United States)

    Vogt, C.; Fähnle, O.; Rascher, R.

    2017-06-01

    While setting up grinding processes for optics fabrication, the optimum tool and process parameters have to be chosen. Unfortunately, datasheets of commercial grinding tools contain only information about grit type and size, bond material, tool shape etc., leaving out any information about process parameters to be applied or tool lifetime or performance. For this reason, tools and machining parameters are commonly adjusted during iterative experimental test runs using actual workpieces from production batches which is time consuming, expensive and without guarantee that the optimum set of machining parameters are achieved. In this paper we present a method to determine grinding tools process window for a given workpiece material. That way, ideal machining parameters can be determined offline for maximum reliability and productivity. In addition, the gained data provides the basis to identify the most suitable grinding tool for the desired application.

  14. IN SITU TRUING/DRESSING OF DIAMOND WHEEL FOR PRECISION GRINDING

    Institute of Scientific and Technical Information of China (English)

    WAN Daping; WANG Yan; HU Dejin

    2008-01-01

    An application for achieving on-machine truing/dressing and monitoring of diamond wheel is dealt with in dry grinding. A dry electrical discharge (ED) assisted truing and dressing method is adopted in preparation of diamond grinding wheels. Effective and precise truing/dressing of a diamond wheel is carried out on a CNC curve grinding machine by utilizing an ED assisted diamond dresser. The dressed wheel is monitored online by a CCD vision system. It detects the topography changes of a wheel surface. The wear condition is evaluated by analyzing the edge deviation of a wheel image. The benefits of the proposed methods are confirmed by the grinding experiments. The designed truing/dressing device has high material removal rate, low dresser wear, and hence guarantees a desired wheel surface. Real-time monitoring of the wheel profile facilitates determining the optimum dressing amount, dressing interval, and the compensation error.

  15. Modeling and Simulation of Process-Machine Interaction in Grinding of Cemented Carbide Indexable Inserts

    National Research Council Canada - National Science Library

    Feng, Wei; Yao, Bin; Chen, BinQiang; Zhang, DongSheng; Zhang, XiangLei; Shen, ZhiHuang

    2015-01-01

      Interaction of process and machine in grinding of hard and brittle materials such as cemented carbide may cause dynamic instability of the machining process resulting in machining errors and a decrease in productivity...

  16. Modeling and analysis of grinding force in ultrasonic honing considering the scale effect

    Directory of Open Access Journals (Sweden)

    Linzheng Ye

    2016-01-01

    Full Text Available To research the power ultrasonic honing mechanism at the micro scale, the scale effect is considered and the strain gradient plasticity theory based on the dislocation mechanism (MSG is applied to establish the model of a whetstone grinding force, and the simulation analysis is conducted. Results show: the grinding force will increase when the scale effect is considered; the main influence parameter is honing depth on the grinding force; the grinding force increases nonlinearly with the continued reduce of honing depth after which decreases to 1.4 μm, which decreases slightly with the increase of the relative velocity of a whetstone. So the material becomes difficult to remove at the micro scale.

  17. Optimization of Cylindrical Grinding Process Parameters on C40E Steel Using Taguchi Technique

    Directory of Open Access Journals (Sweden)

    Naresh Kumar

    2015-01-01

    Full Text Available Surface finish and dimensional accuracy play a vital role in the today’s engineering industry. There are several methods used to achieve good surface finish like burnishing, honing and lapping, and grinding. Grinding is one of these ways that improves the surface finish and dimensional accuracy simultaneously. C40E steel has good industrial application in manufacturing of shafts, axles, spindles, studs, etc. In the present work the cylindrical grinding of C40E steel is done for the optimization of grinding process parameters. During this experimental work input process parameters i.e. speed, feed, depth of cut is optimized using Taguchi L9 orthogonal array. Analysis of variance (ANOVA concluded that surface roughness is minimum at the 210 rpm, 0.11mm/rev feed, and 0.04mm depth of penetration.

  18. Quality Estimation of Dry Grinding of Skiving Cutters With Organic Bonding Diamond Wheels

    Science.gov (United States)

    Filippov, A. V.; Shamarin, N. N.; Podgornykh, O. A.; Rubtsov, V. E.

    2016-08-01

    Engineering process preparation requires proper preparation of cutting tools. It influences not only the performance of the tools but also the quality of workpiece surface machining. One of the promising environmentally friendly trends of mechanical treatment is grinding without using lubricating cooling liquid. This method can considerably influence the quality of cutting tools grinding. Smoothing skiving turning is an effective treatment method providing high efficiency and workpiece quality. Proper preparation of cutting edges is especially important in this process. For that purpose we have carried out a research in grinding changeable carbide inserts for skiving turning by means of grinding wheels with different grain size. The influence of different combinations of wheels on roughness of the inserts front and rear surfaces and quality of cutting edge was studied with the help of laser confocal microscopy.

  19. Effects of supercritical water and mechanochemical grinding treatments on physicochemical properties of chitin.

    Science.gov (United States)

    Osada, Mitsumasa; Miura, Chika; Nakagawa, Yuko S; Kaihara, Mikio; Nikaido, Mitsuru; Totani, Kazuhide

    2013-02-15

    This study examined the effects of a combined pretreatment with supercritical water and mechanochemical grinding with a ball mill on the physicochemical properties of chitin and its enzymatic degradation. Following pretreatment with a combination of supercritical water and grinding, chitin had a lower mean molecular weight, a lower crystallinity index, a lower crystallite size, greater d-spacing, weaker hydrogen bonds, and the amide group was more exposed compared with untreated chitin. These properties increased the hydrophilicity of the chitin and enhanced its enzymatic degradation. The N,N'-diacetylchitobiose (GlcNAc)(2) yield after enzymatic degradation of chitin following pretreatment with supercritical water (400 °C, 1 min) and grinding (800 rpm, 10 min) was 93%, compared with 5% without any treatment, 37% with supercritical water pretreatment alone (400 °C, 1 min), and 60% with grinding alone (800 rpm, 30 min).

  20. Dynamic modeling and analysis of the closed-circuit grinding-classification process

    Institute of Scientific and Technical Information of China (English)

    Yunfei Chu; Wenli Xu; Weihan Wan

    2005-01-01

    Mathematical models of the grinding process are the basis of analysis, simulation and control. Most existent models including theoretical models and identification models are, however, inconvenient for direct analysis. In addition, many models pay much attention to the local details in the closed-circuit grinding process while overlooking the systematic behavior of the process as a whole. From the systematic perspective, the dynamic behavior of the whole closed-circuit grinding-classification process is considered and a first-order transfer function model describing the dynamic relation between the raw material and the product is established.The model proves that the time constant of the closed-circuit process is lager than that of the open-circuit process and reveals how physical parameters affect the process dynamic behavior. These are very helpful to understand, design and control the closed-circuit grinding-classification process.

  1. The effects of three different grinding methods in DNA extraction of ...

    African Journals Online (AJOL)

    uwerhiavwe

    2013-04-17

    Apr 17, 2013 ... downstream PCR analysis without liquid nitrogen, the cowpea DNA was extracted by ... obtained by three grinding methods both in CTAB method and SDS method. Without ..... the proteins and lipids that form the membranes.

  2. Effect of electromagnetic radiation on the kinetics of grinding a mineral; Efecto de la radiacion electromagnetica en la cinetica de molienda de un mineral

    Energy Technology Data Exchange (ETDEWEB)

    Lopez M, A.; Delgadillo G, J. A. [Universidad Autonoma de San Luis Potosi, Instituto de Metalurgia, Av. Sierra Leona 550, 78210 San Luis Potosi (Mexico); Vega C, H. R., E-mail: alopezm6@yahoo.com.mx [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico)

    2015-10-15

    In this study the effect of kinetic grinding of a mineral was investigated when is pre treated with ionizing electromagnetic radiation. This radiation is with 15 MeV photons produced by a Linac for Radiotherapy. The results for the irradiated sample with respect to the non-irradiated indicate that there were changes in the structure of the minerals in the sample under study. Changes were observed through scanning electron microscopy and X-ray diffraction, combined with the refinement of the diffraction profiles by the Rietveld method using the software Maud Program. The grinding kinetics shows a constant distribution of slightly greater size through time used for the irradiated sample. A reduction of 11.2% of the Bond (Wi) work index was reached, going from 10.91 to 9.69 kw h/t for the irradiated sample. This parameter represents the fracture toughness of a mineral. The results indicate greater efficiency of energy applied to the grinding of the irradiated sample with respect to the non-irradiated. (Author)

  3. Effect of cryogenic grinding on volatile and fatty oil constituents of cumin (Cuminum cyminum L.) genotypes.

    Science.gov (United States)

    Sharma, L K; Agarwal, D; Rathore, S S; Malhotra, S K; Saxena, S N

    2016-06-01

    Effect of cryogenic grinding on recovery of volatile oil, fatty oil percentage and their constituents in two cumin (Cuminum cyminum L.) genotypes have been analyzed. Cryogenic grinding not only retains the volatiles but enhanced the recovery by 33.9 % in GC 4 and 43.5 % in RZ 209. A significant increase (29.9 %) over normal grinding in oil percentage was also observed in genotype RZ 209. This increase was, however, less (15.4 %) in genotype GC 4. Nineteen major compounds were identified in the essential oil of both genotypes. The two grinding techniques had significant effects on dependent variables, viz., volatile oil and monoterpenes. Cuminaldehyde was the main constituent in both genotypes, content of which increased from 48.2 to 56.1 % in GC 4 on cryo grinding. Content of terpines were found to decrease in cryo ground samples of GC 4 and either decrease or no change was found in RZ 209. Organoleptic test showed more pleasant aroma in cryo ground seeds of both the genotypes. Significant increase was also reported in fatty oil yield due to cryogenic grinding. Fatty acid methyl ester (FAME) analysis showed oleic acid as major FAME content of which increased from 88.1 to 94.9 % in RZ 209 and from 88.2 to 90.1 % in GC 4 on cryogenic grinding. Other prominent FAME were palmitic, palmitoleic and stearic acid. Results indicated commercial potential of cryogenic grinding technology for cumin in general and spices in particular for better retention of flavour and quality in spices.

  4. Experimental Investigation on the Performance of Grinding Assisted Electrochemical Discharge Drilling of Glass

    OpenAIRE

    Ladeesh V. G.; Manu R

    2016-01-01

    Grinding assisted electrochemical discharge drilling (G-ECDD) is a novel technique for producing micro and macro holes in brittle materials including advanced ceramics and glass, both efficiently and economically. G-ECDD involves the use of a rotating diamond core drill as the tool in a normal electrochemical discharge machine setup. The material removal happens by a combination of thermal melting due to electric discharges, followed by grinding action of diamond grits and chemical etching ac...

  5. Surface roughness of zirconia for full-contour crowns after clinically simulated grinding and polishing

    Institute of Scientific and Technical Information of China (English)

    Rim Hmaidouch; Wolf-Dieter Mu ller; Hans-Christoph Lauer; Paul Weigl

    2014-01-01

    The aim of this study was to evaluate the effect of controlled intraoral grinding and polishing on the roughness of full-contour zirconia compared to classical veneered zirconia. Thirty bar-shaped zirconia specimens were fabricated and divided into two groups (n515). Fifteen specimens (group 1) were glazed and 15 specimens (group 2) were veneered with feldspathic ceramic and then glazed. Prior to grinding, maximum roughness depth (Rmax) values were measured using a profilometer, 5 times per specimen. Simulated clinical grinding and polishing were performed on the specimens under water coolant for 15 s and 2 N pressure. For grinding, NTI diamonds burs with grain sizes of 20 mm, 10 mm, and 7.5 mm were used sequentially. The ground surfaces were polished using NTI kits with coarse, medium and fine polishers. After each step, Rmax values were determined. Differences between groups were examined using one-way analysis of variance (ANOVA). The roughness of group 1 was significantly lower than that of group 2. The roughness increased significantly after coarse grinding in both groups. The results after glazing were similar to those obtained after fine grinding for non-veneered zirconia. However, fine-ground veneered zirconia had significantly higher roughness than venerred, glazed zirconia. No significant difference was found between fine-polished and glazed zirconia, but after the fine polishing of veneered zirconia, the roughness was significantly higher than after glazing. It can be concluded that for full-contour zirconia, fewer defects and lower roughness values resulted after grinding and polishing compared to veneered zirconia. After polishing zirconia, lower roughness values were achieved compared to glazing;more interesting was that the grinding of glazed zirconia using the NTI three-step system could deliver smooth surfaces comparable to untreated glazed zirconia surfaces.

  6. Mechanical Property of Low Chromium Semi-Steel Grinding Ball Prepared by Cross Rolling

    Institute of Scientific and Technical Information of China (English)

    CHANG Li-min; MENG De-liang; NIE Pu-lin; LIU Jian-hua

    2004-01-01

    The preparing method, rolling technology and mechanical properties of low chromium semi-steel grinding ball by cross rolling were studied. The results show that when the low chromium semi-steel bar is forged from 55 mm to 50 mm, cross-rolled into grinding ball at 1 000-1 050 ℃, air cooled and tempered at 550 ℃ for 2 h, the best mechanical properties, especially the abrasive resistance under the action of hard abrasive, can be obtained.

  7. Surface roughness of zirconia for full-contour crowns after clinically simulated grinding and polishing.

    Science.gov (United States)

    Hmaidouch, Rim; Müller, Wolf-Dieter; Lauer, Hans-Christoph; Weigl, Paul

    2014-12-01

    The aim of this study was to evaluate the effect of controlled intraoral grinding and polishing on the roughness of full-contour zirconia compared to classical veneered zirconia. Thirty bar-shaped zirconia specimens were fabricated and divided into two groups (n=15). Fifteen specimens (group 1) were glazed and 15 specimens (group 2) were veneered with feldspathic ceramic and then glazed. Prior to grinding, maximum roughness depth (Rmax) values were measured using a profilometer, 5 times per specimen. Simulated clinical grinding and polishing were performed on the specimens under water coolant for 15 s and 2 N pressure. For grinding, NTI diamonds burs with grain sizes of 20 µm, 10 µm, and 7.5 µm were used sequentially. The ground surfaces were polished using NTI kits with coarse, medium and fine polishers. After each step, Rmax values were determined. Differences between groups were examined using one-way analysis of variance (ANOVA). The roughness of group 1 was significantly lower than that of group 2. The roughness increased significantly after coarse grinding in both groups. The results after glazing were similar to those obtained after fine grinding for non-veneered zirconia. However, fine-ground veneered zirconia had significantly higher roughness than venerred, glazed zirconia. No significant difference was found between fine-polished and glazed zirconia, but after the fine polishing of veneered zirconia, the roughness was significantly higher than after glazing. It can be concluded that for full-contour zirconia, fewer defects and lower roughness values resulted after grinding and polishing compared to veneered zirconia. After polishing zirconia, lower roughness values were achieved compared to glazing; more interesting was that the grinding of glazed zirconia using the NTI three-step system could deliver smooth surfaces comparable to untreated glazed zirconia surfaces.

  8. Next generation grinding spindle for cost-effective manufacture of advanced ceramic components

    Energy Technology Data Exchange (ETDEWEB)

    Kovach, J.A.; Laurich, M.A.

    2000-01-01

    Finish grinding of advanced structural ceramics has generally been considered an extremely slow and costly process. Recently, however, results from the High-Speed, Low-Damage (HSLD) program have clearly demonstrated that numerous finish-process performance benefits can be realized by grinding silicon nitride at high wheel speeds. A new, single-step, roughing-process capable of producing high-quality silicon nitride parts at high material removal rates while dramatically reducing finishing costs has been developed.

  9. Accurate Tooth Lead Crowning without Twist in Cylindrical Helical Gear Grinding

    OpenAIRE

    Zhang, Hu; Fang, Chenggang; Huang, XiaoDiao

    2014-01-01

    Form grinding is a popular finishing process in manufacturing cylindrical gears with tooth flank modification. The tooth flanks are usually twisted when a lead crowning is performed only through additional radial motion during double flank grinding. For solving the problem, this paper proposes a method for application of tooth lead crowning without twist in cylindrical helical gears based on the idea of tooth form correction for spiral bevel and hypoid gears. In this method, the motion of eac...

  10. Role of classification in grinding using the electromagnetic mill. A case study

    Directory of Open Access Journals (Sweden)

    Wolosiewicz-Glab Marta

    2016-01-01

    Full Text Available In the process of classification, one of the methods used to evaluate the effectiveness classifiers is to plot a separation curve, which determines the size of seprated particles and characterizes the process accuracy. The article presents an assessment of the impact of parameters on grinding and classification using an electromagnetic mill. The results allow a detailed assessment of the effectiveness and efficiency of the device and facilitate the optimization of the grinding process by establishing an appropriate control algorithms.

  11. 3MK1420外沟磨床砂轮修整器改造%Improvement of grinding wheel dresser for 3MK1420 outer groove grinding machine

    Institute of Scientific and Technical Information of China (English)

    姚淑敏

    2013-01-01

    Aiming at the problem of chain drive in grinding wheel dresser for 3MK1420 outer groove grinding machine, chain drive is superseded by steel belt drive so as to improve the drive stability and the dressing quality.%  针对3MK1420外沟磨床砂轮修整器链条传动存在的问题,采用钢带传动取代链条传动,提高了传动平稳性及砂轮修整质量。

  12. Poly(ethylene glycol)s as grinding additives in the mechanochemical preparation of highly functionalized 3,5-disubstituted hydantoins

    Science.gov (United States)

    Guerra, Ruben; Taydakov, Ilya; Tonucci, Lucia; d’Alessandro, Nicola; Lamaty, Frederic; Martinez, Jean

    2017-01-01

    Summary The mechanochemical preparation of highly functionalized 3,5-disubstituted hydantoins was investigated in the presence of various poly(ethylene) glycols (PEGs), as safe grinding assisting agents (liquid-assisted grinding, LAG). A comparative study under dry-grinding conditions was also performed. The results showed that the cyclization reaction was influenced by the amount of the PEG grinding agents. In general, cleaner reaction profiles were observed in the presence of PEGs, compared to dry-grinding procedures.

  13. 不同研磨时间对咖啡感官风味的影响%Effects of Different Grinding Time on Sensory Flavor of Coffee

    Institute of Scientific and Technical Information of China (English)

    胡荣锁; 谷风林; 宗迎; 吴桂苹; 房一明; 卢少芳; 魏来

    2012-01-01

    Because coffee particle breaking in the grinding process, coffee flavor substances lost a lot, in order to explore the coffee grinding for coffee senses flavor influence, roasted coffee beans were grinded with plant crusher and mortar mill for different intervals, and chromatic meter was used to analyze the photosensitive change and electronic tongue and electronic noses qualitatively describe coffee sensory flavor in the grinding process. The lab results showed that the coffee color became shallow gradually in the first 9 minutes, and then deepened gradually. A large number of flavor substances dissipated in the first 9 minutes, and then volatilizing speed decreased. The PCA and DFA analysis of electronic nose and electronic tongue indicated that the taste and smell gradually changed as time increased, and SQC results showed that the smell of the samples of different grinding time changed slightly within acceptable limits, but tasted, only sample of 5 minutes grinding was within the acceptable limits, while others were not within acceptable limits. So coffee grinding time to less than 5 min, in order to avoid coffee flavor substances losting, so that coffee senses flavor reduced.%咖啡在研磨过程中因咖啡颗粒破碎,使风味物质大量散失,为了探索咖啡研磨对咖啡感官风味的影响,利用植物粉碎机和臼式研磨机,将焙炒好的咖啡豆按不同时间粉碎研磨,用色差仪分析研磨过程中咖啡的光敏性变化以及用电子舌、电子鼻对咖啡研磨过程中感官风味进行定性表达.Lab数据结果表明,在前9 min颜色逐渐变浅,然后随之逐渐加深.在前9min有大量风味物质逸散,其后逸散速率减缓.电子鼻和电子舌PCA和DFA分析均表明,随着时间的增加,口感和香味逐渐变化,SQC结果表明不同研磨时间的样品虽然气味变化不是很大,在可接受范围内,但是口感变化较大,只有研磨5 min样品在可接受范围内,其他均不在可接受范围内.

  14. The effects of pf grind quality on coal burnout in a 1 MW combustion test facility

    Energy Technology Data Exchange (ETDEWEB)

    Richelieu Barranco; Michael Colechin; Michael Cloke; Will Gibb; Edward Lester [University of Nottingham, Nottingham (United Kingdom). School of Chemical, Environmental and Mining Engineering, Nottingham Fuel and Energy Centre

    2006-05-15

    A study was carried out to determine the effect of pf particle size distribution on coal burnout propensity in a 1 MW pulverised fuel burner. The specific aim of the work was to assess the improvement in combustion performance achievable by retrofitting commercially available high performance static or dynamic classifiers to existing plants. Two coals were used and were selected as representative of extremes in fuel characteristics experienced by coal importing utilities in Europe. Each coal was fired in the unit at a range of grind sizes to determine the overall impact of a variable performance from a mill. The levels of unburnt carbon in the resultant flyashes for the two coals showed significantly different behaviour. For the higher volatile coal, the unburnt carbon was found to be insensitive to grind quality. However, the coarser grinds of the other coal produced significantly lower unburnt carbon than expected when compared with the finest grinds. Generally the results indicate that the installation of improved classification technology, leading to a finer product, will help to lower unburnt carbon levels. Nevertheless, further work will be necessary to establish the levels of diminishing returns for grind size, burnout performance and grind costs. 21 refs., 4 figs., 4 tabs.

  15. Diagnostic value of clinical grind test for carpometacarpal osteoarthritis of the thumb.

    Science.gov (United States)

    Merritt, Melissa M; Roddey, Toni S; Costello, Charles; Olson, Sharon

    2010-01-01

    Clinical Measurement. Thumb carpometacarpal (CMC) osteoarthritis is a frequent cause of thumb pain. To evaluate the interrater reliability and the criterion validity of the grind test for thumb CMC osteoarthritis. Radiological evaluation was used as the gold standard. Seventy thumbs of 54 persons with various hand disorders were included in the study. The grind test was performed by two physical therapists, and radiographs were evaluated by a certified hand surgeon, all blinded to the participants' diagnosis and other test results. Interrater reliability was compared with a kappa statistic, and the sensitivity, specificity, likelihood ratios, and predictive values were calculated from a 232 table. A kappa value of 0.48 was calculated as the interrater reliability. The sensitivity of the grind test was 42% and 53%, depending on tester. The specificity of the grind test was 80% and 93%, depending on tester. The positive likelihood ratio was 2.65 and 6.00, and the negative likelihood ratio was 0.59 and 0.62. The positive predictive value was 91% and 96%, depending on tester. The negative predictive value was 68% and 70%, depending on tester. The grind test has moderate reliability and accurately confirms the diagnosis of CMC osteoarthritis and identifies those who do not have CMC osteoarthritis. However, a negative grind test does not necessarily reflect negative radiographic evidence of thumb CMC osteoarthritis. n/a. Copyright © 2010 Hanley & Belfus. Published by Elsevier Inc. All rights reserved.

  16. Analysis and Compensation for Gear Accuracy with Setting Error in Form Grinding

    Directory of Open Access Journals (Sweden)

    Chenggang Fang

    2015-01-01

    Full Text Available In the process of form grinding, gear setting error was the main factor that influenced the form grinding accuracy; we proposed an effective method to improve form grinding accuracy that corrected the error by controlling the machine operations. Based on establishing the geometry model of form grinding and representing the gear setting errors as homogeneous coordinate, tooth mathematic model was obtained and simplified under the gear setting error. Then, according to the gear standard of ISO1328-1: 1997 and the ANSI/AGMA 2015-1-A01: 2002, the relationship was investigated by changing the gear setting errors with respect to tooth profile deviation, helix deviation, and cumulative pitch deviation, respectively, under the condition of gear eccentricity error, gear inclination error, and gear resultant error. An error compensation method was proposed based on solving sensitivity coefficient matrix of setting error in a five-axis CNC form grinding machine; simulation and experimental results demonstrated that the method can effectively correct the gear setting error, as well as further improving the forming grinding accuracy.

  17. Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

    Directory of Open Access Journals (Sweden)

    Chen Zhenzhen

    2014-08-01

    Full Text Available For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function. However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride (CBN wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temperature, which were better than those of the vitrified one under the same grinding conditions. Compared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.

  18. Some Key Technologies of a New-type CNC Curve Grinding Machine

    Institute of Scientific and Technical Information of China (English)

    WU Qi; HU De-jin

    2007-01-01

    This paper presented a new-type CNC curve grinding machine, in order to conquer the disadvantages of conventional NC curve grinding machine and improve surface quality, dimensional accuracy and machining efficiency. The new-type grinder adopts some high and new technologies:①the normal tracing device could make grinding wheel coincide with the normal direction of the machining points in work piece, and improve surface quality and dimensional accuracy;②the digital image on-line recognition system could monitor machining process and compensate wheel wear in real time;③linear motor drive mechanism could realize the exact adjustment of the grinding head digitally and increase the machining efficiency. The math models of normal tracing and circular tolerance zone were presented. The experimental results show that the new-type CNC curve grinding machine equipped with the three devices mentioned above is easy to realize the precision grinding of any complex curve, and improve surface quality, dimensional accuracy and machining efficiency.

  19. Research on Ultrasonic Vibration Grinding of the Hard and Brittle Materials

    Institute of Scientific and Technical Information of China (English)

    YANG Xin-hong; HAN Jie-cai; ZHANG Yu-min; ZUO Hong-bo; ZHANG Xue-jun

    2006-01-01

    It is well known that grinding techniques are main methods to machine hard and brittle materials such as engineering ceramics. But the conventional grinding has many shortcomings such as poorer surface finish, quicker wear and tear of grinding tools, lower efficiency and so on. Ultrasonic vibration grinding (UVG) which combines ultrasonic machining and grinding emerged as a developing and promising technique in recent years. In this paper, experimental studies on UVG were conducted on several kinds of hard and brittle material by altering processing parameters such as vibration frequency and its amplitude, diamond abrasive grit size, cutting depth, feeding speed and rotary speed of tools. The experimental results show that alteration in any of above mentioned parameters will bring effects on the processed surface finish of these materials. Of them, the diamond abrasive grit size has the greatest. Moreover, conventional grinding experiments were also carried out on these materials. By comparison, it was found that the UVG is superior to the conventional method in terms of the ground surface quality, the working efficiency and the wear rate of tools.

  20. Beneficiation of low grade graphite ore of eastern India by two-stage grinding and flotation

    Directory of Open Access Journals (Sweden)

    Vasumathi N.

    2014-01-01

    Full Text Available A low grade graphite run-of-mine (r.o.m ore from eastern India was studied for its amenability to beneficiation by flotation technique. The petrography studies indicate that the ore primarily consists of quartz and graphite with minor quantity of mica. It analyzed 89.89% ash and 8.59% fixed carbon. The ore was crushed in stages followed by primary coarse wet grinding to 212 μm (d80. Rougher flotation was carried out in Denver flotation cell to eliminate gangue as much as possible in the form of primary tailings with minimal loss of carbon. Diesel & pine oil were used as collector and frother respectively. Regrinding of rougher concentrate to150 μm (d80 was resorted to further liberate the graphite values and was followed by multi-stage cleaning. This two-stage grinding approach involving a primary coarse grinding and regrinding of rougher float followed by its multi-stage cleaning was found to yield required grade of concentrate for applications such as refractories, batteries and high temperature lubricants. This approach is supposed to retain the flake size of coarse, free and liberated graphite, if available, during primary coarse grinding and rougher flotation stage with minimal grinding energy costs as against the usual practice of single stage grinding in the case of many ores. A final concentrate of 8.97% weight recovery with 5.80% ash and 92.13% fixed carbon could be achieved.

  1. High speed low damage grinding of advanced ceramics - Phase II Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Kovach, J.A.; Malkin, S.

    2000-02-01

    In the manufacture of structural ceramic components, grinding costs can comprise up to 80% of the entire manufacturing cost. As a result, one of the most challenging tasks faced by manufacturing process engineers is the development of a ceramic finishing process to maximize part throughput while minimizing costs and associated scrap levels. The efforts summarized in this report represent the second phase of a program whose overall objective was to develop a single-step, roughing-finishing process suitable for producing high-quality silicon nitride parts at high material removal rates and at substantially lower cost than traditional, multi-stage grinding processes. More specifically, this report provides a technical overview of High-Speed, Low-Damage (HSLD) ceramic grinding which employs elevated wheel speeds to achieve the small grain depths of cut necessary for low-damage grinding while operating at relatively high material removal rates. The study employed the combined use of laboratory grinding tests, mathematical grinding models, and characterization of the resultant surface condition. A single-step, roughing-finishing process operating at high removal rates was developed and demonstrated.

  2. Virtual Sensors for On-line Wheel Wear and Part Roughness Measurement in the Grinding Process

    Directory of Open Access Journals (Sweden)

    Ander Arriandiaga

    2014-05-01

    Full Text Available Grinding is an advanced machining process for the manufacturing of valuable complex and accurate parts for high added value sectors such as aerospace, wind generation, etc. Due to the extremely severe conditions inside grinding machines, critical process variables such as part surface finish or grinding wheel wear cannot be easily and cheaply measured on-line. In this paper a virtual sensor for on-line monitoring of those variables is presented. The sensor is based on the modelling ability of Artificial Neural Networks (ANNs for stochastic and non-linear processes such as grinding; the selected architecture is the Layer-Recurrent neural network. The sensor makes use of the relation between the variables to be measured and power consumption in the wheel spindle, which can be easily measured. A sensor calibration methodology is presented, and the levels of error that can be expected are discussed. Validation of the new sensor is carried out by comparing the sensor’s results with actual measurements carried out in an industrial grinding machine. Results show excellent estimation performance for both wheel wear and surface roughness. In the case of wheel wear, the absolute error is within the range of microns (average value 32 μm. In the case of surface finish, the absolute error is well below Ra 1 μm (average value 0.32 μm. The present approach can be easily generalized to other grinding operations.

  3. Multiobjective Optimization of ELID Grinding Process Using Grey Relational Analysis Coupled with Principal Component Analysis

    Directory of Open Access Journals (Sweden)

    S. Prabhu

    2014-06-01

    Full Text Available Carbon nanotube (CNT mixed grinding wheel has been used in the electrolytic in-process dressing (ELID grinding process to analyze the surface characteristics of AISI D2 Tool steel material. CNT grinding wheel is having an excellent thermal conductivity and good mechanical property which is used to improve the surface finish of the work piece. The multiobjective optimization of grey relational analysis coupled with principal component analysis has been used to optimize the process parameters of ELID grinding process. Based on the Taguchi design of experiments, an L9 orthogonal array table was chosen for the experiments. The confirmation experiment verifies the proposed that grey-based Taguchi method has the ability to find out the optimal process parameters with multiple quality characteristics of surface roughness and metal removal rate. Analysis of variance (ANOVA has been used to verify and validate the model. Empirical model for the prediction of output parameters has been developed using regression analysis and the results were compared for with and without using CNT grinding wheel in ELID grinding process.

  4. Grinding performance evaluation of porous composite-bonded CBN wheels for Inconel 718

    Institute of Scientific and Technical Information of China (English)

    Chen Zhenzhen; Xu Jiuhua; Ding Wenfeng; Ma Changyu

    2014-01-01

    For high-efficiency grinding of difficult-to-cut materials such as titanium and nickel alloys, a high porosity is expected and also a sufficient mechanical strength to satisfy the function. However, the porosity increase is a disadvantage to the mechanical strength. As a promising pore forming agent, alumina bubbles are firstly induced into the abrasive layer to fabricate porous cubic boron nitride (CBN) wheels. When the wheel porosity reaches 45%, the bending strength is still high up to 50 MPa with modified orderly pore distribution. A porous CBN wheel was fabricated with a total porosity around 30%. The grinding performance of the porous composite-bonded CBN wheel was evaluated in terms of specific force, specific grinding energy, and grinding temper-ature, which were better than those of the vitrified one under the same grinding conditions. Com-pared to the vitrified CBN wheel, clear straight cutting grooves and less chip adhesion are observed on the ground surface and there is also no extensive loading on the wheel surface after grinding.

  5. Improved grinding quality inspection of large bearing components using Barkhausen noise analysis

    Science.gov (United States)

    Kolarits, Francis M.

    2014-02-01

    Assuring that the finished surfaces of precision large bearing components are free from grinding injury is important due to the high initial value of these bearings, heavy application loadings and high costs associated with potential reduced service life. Inspecting bearing raceway surfaces for grind burn can be done by nital etching but this method is time consuming, involves using hazardous acids, is non-quantitative and does not provide information about residual stresses. An experimental study was performed to assess scanning Barkhausen Noise Analysis (BNA) to detect various levels of induced grind injury on four steels used in large bearing ring production. Test samples having approximately 0.25 m diameter were fabricated from bearing steels heat treated by case carburizing, induction hardening and through hardening. A series of grinding cycles was designed and subsequently the entire ground surface on each sample was tested by scanning BNA. Selected samples were then evaluated by nital etching or destructive metallurgical tests. BNA results are compared with specific grinding power, nital etch and destructive measurements to show BNA to be an effective technique for identification of grind injury on these steel materials. Similar relative trends in the BNA response are present regardless of alloy or heat treatment.

  6. Dechlorination of pentachlorophenol by grinding at low rotation speed in short time

    Institute of Scientific and Technical Information of China (English)

    Zhi Xu; Xiaoyu Zhang; Qingzhi Fei

    2015-01-01

    In order to apply grinding method for degradation of pentachlorophenol (PCP) to an industrial scale, the propor-tion of different materials [CaO, SiO2 and CO(NH2)2] and the size of grinding balls were examined. For saving en-ergy and increasing dechlorination efficiency, the rotation speed and grinding time were maintained at relatively low values. At a mass ratio of grinding bal s to materials (40:1), PCP was added into a big steel jar (300 ml) with other materials to grind at 300 r·min−1 for 5 h. The results indicated that when PCP was mixed with CaO and SiO2 in a molar ratio of 1:60:60, the best dechlorination of 58.4%was achieved. CO(NH2)2 could not be used as hydro-gen donor in the dehalogenation by mechanochemical reaction, since it restrained the dechlorination process. The size of grinding balls has significant effect on the reaction. The experiment with 5 mm steel balls indicates that the weight is too light to provide appropriate energy for the reaction, while steel balls of 10 and 15 mm could give better dechlorination reaction. It indicates that dechlorination depends on the mass of balls and fill rate.

  7. Clenching and grinding: effect on masseter and sternocleidomastoid electromyographic activity in healthy subjects.

    Science.gov (United States)

    Venegas, Macarena; Valdivia, José; Fresno, María Javiera; Miralles, Rodolfo; Gutiérrez, Mario Felipe; Valenzuela, Saúl; Fuentes, Aler

    2009-07-01

    This study compares the effect of clenching and grinding on masseter and sternocleidomastoid electromyographic (EMG) activity during different jaw posture tasks in the sagittal plane. The study included 34 healthy subjects with natural dentition, Class I bilateral molar Angle relationship, and absence of posterior occlusal contacts during mandibular protrusion. An inclusion criterion was that subjects had to be free of signs and symptoms of any dysfunction of the masticatory system. Bipolar surface electrodes were located on the right masseter and sternocleidomastoid muscles. EMG activity was recorded while the subjects were in standing position, during the following jaw posture tasks: A. maximal clenching in the intercuspal position; B. grinding from intercuspal position to edge-to-edge protrusive contact position; C. maximal clenching in the edge-to-edge protrusive contact position; D. grinding from edge-to-edge protrusive contact position to intercuspal position; E. grinding from retrusive contact position to intercuspal position. EMG activities in tasks B, C, D, and E were significantly lower than in task A in both muscles (mixed model with unstructured covariance matrix). EMG activity among tasks B, C, D, and E did not show significant differences in both muscles, except between tasks D and E in the masseter muscle. A higher effect was observed on the masseter than on the sternocleidomastoid muscle to avoid excessive muscular activity during clenching and grinding. The EMG patterns observed could be of clinical importance in the presence of parafunctional habits, i.e., clenching and/or grinding.

  8. Design and experimental research of the on-line detection system for diamond arc grinding wheel

    Science.gov (United States)

    Zhang, Feihu; Li, Chen; Liu, Zhongde; Ren, Lele; Xie, Haisheng

    2016-10-01

    The principle of measuring displacement by eddy current sensor was derived. The calibration experiment was carried out for 5 kinds of different materials, which showed that the linearity of eddy current sensor was better, and the sensitivity of eddy current sensor varied with different materials. Based on the principle of measuring displacement by eddy current sensor, the on-line detection system for diamond circular wheel was designed, and the data acquisition was realized by using LABVIEW software. By moving the eddy current sensor in the vertical direction with the grinding wheel fixed, the coordinate of arc in the grinding wheel was obtained. The radius of the grinding wheel was fitted by using the genetic algorithm, which showed that the fitting results were accurate. The data acquisition of the grinding wheel was carried out in a cycle by fixing the electric eddy current sensor and the circulars of the grinding wheel in different processes, namely before dressing, after dressing and after shaping. The results showed that the circular of the grinding wheel after dressing and after shaping were significantly improved compared with that before dressing.

  9. Numerical Simulation of a Grinding Process Model for the Spatial Work-pieces: Development of Modeling Techniques

    Directory of Open Access Journals (Sweden)

    S. A. Voronov

    2015-01-01

    Full Text Available The article presents a literature review in simulation of grinding processes. It takes into consideration the statistical, energy based, and imitation approaches to simulation of grinding forces. Main stages of interaction between abrasive grains and machined surface are shown. The article describes main approaches to the geometry modeling of forming new surfaces when grinding. The review of approaches to the chip and pile up effect numerical modeling is shown. Advantages and disadvantages of grain-to-surface interaction by means of finite element method and molecular dynamics method are considered. The article points out that it is necessary to take into consideration the system dynamics and its effect on the finished surface. Structure of the complex imitation model of grinding process dynamics for flexible work-pieces with spatial surface geometry is proposed from the literature review. The proposed model of spatial grinding includes the model of work-piece dynamics, model of grinding wheel dynamics, phenomenological model of grinding forces based on 3D geometry modeling algorithm. Model gives the following results for spatial grinding process: vibration of machining part and grinding wheel, machined surface geometry, static deflection of the surface and grinding forces under various cutting conditions.

  10. Analysing a Relationship Between Wheel Wear and Cutting Forces During Diamond Grinding

    Directory of Open Access Journals (Sweden)

    M. A. Shavva

    2014-01-01

    Full Text Available In diamond grinding cutting forces affect the quality of the machined surface. We can estimate a wear rate of the diamond wheel by the magnitude of the forces and promptly resort to the restoration of its cutting properties. To solve this problem it is necessary to define a relationship between grinding wheel wear and cutting forces. There was no this dependence found in the sources of literature.The forces acting on a single worn diamond grain are considered to find the relationship between wheel wear and cutting forces. The main forces acting on the diamond grain are such as a reaction force of machining material, a frictional force over a worn place of the grain, and a total pressure on the contact surface of the grain and machining material. According to calculation results, in grinding the cutting forces are proportional to the hardness of machining material, and depend on the grain wear, as well as on the process operation conditions.The paper presents a technique for calculating the number of cutting (active grains per unit surface of diamond wheel to determine a total cutting force in grinding. The number of cutting grains depends on the properties of diamond wheel and on the operation conditions of grinding process.During grinding a total cutting force is calculated through the single grain cutting force, the number of cutting grains per unit surface of the grinding wheel and the contact area between the wheel and the work piece. Theoretical calculation of the forces is based on the condition that protrusions of all cutting grains are identical and all grains have a maximum wear, i.e. maximum worn place of grain.Calculations based on proposed theoretical formulas are compared with the calculations from the empirical formulas given in the literature. Varying the operation conditions of grinding makes the comparison. Convergence of results in the range of 5-20% is regarded as acceptable.On the BMSTU base flat diamond grinding of tungsten

  11. A Study on the Model for Resources Matching of Electronic Bartering%电子易货资源匹配模型研究

    Institute of Scientific and Technical Information of China (English)

    吴剑云; 张嵩

    2012-01-01

    By exchanging idle goods and services, electronic bartering can help enterprises solve dull sale problems, shortage of funds, overstocks and other problems without sufficient cash. Relying on the Internet and the e-commerce platform, electronic bartering removes the traditional bartering limitations, greatly expands the trading object and range, improves the transaction efficiency, and provides additional channels for economic development. How to promote more successful barters among multiple barterers? A key factor is the matching of barter resources. Focusing on the automatic matching of resources in the electronic barter, this paper proposes a network model to help maximize resources matching and provide recommendation information for barter participants, thereby raising the transaction rate and making the barter market prosperous.According to the type and quantity of barter resources, barter market can be divided into two types. In the first type, the supply and demand of the barter market is related to the same type of resources and each barterer owns only one type of resource. In the second type, the supply and demand of the barter market is linked to many types of resources and each barterer owns multiple resources to be exchanged. The first case has been resolved in the relevant document by using the graph theory to solve digraph circuits. This paper is interested in studying the second type of barter. Suppose the barter market has m barterers and n resources. Each barterer owns diverse types of barter resources, and is interested in other types of resources. The barterer a will provide other barterers his own resources only if he gets the resources he needs from the barterer b. Note that each of the bartered resource is regarded as having equal value to any other resources. The main objective is to maximize the number of resources that are bartered.Next, this paper proposes a math model of automatic resources matching by systematically analyzing resource

  12. Grinding and polishing technology by computer controlled active lap for Φ1250mmF/1.5 aspheric mirror

    Science.gov (United States)

    Fan, Bin; Zeng, Zhige; Li, Xiaojin; Chen, Qiang; Gao, Pingqi; Zhou, Jiabin; Wan, Yongjian

    2010-05-01

    For large aspheric optical elements, Computer Controlled Active Lap(CCAL) manufacturing which developed in IOE (Institute of Optics and Electronics, Chinese Academy of Science), have some advantages such as higher manufacturing efficiency, lower middle-frequency and high-frequency errors comparing the fixed lapping technology and CCOS(Computer Controlled Optical Surface) technology. A paraboloid surface of Φ1250mmF/1.5 was grinded by the active lap bonded with ceramic pills, as well as polished will pitch bonded active lap. During polishing processing a null lens was designed to test the paraboloid surface, the final testing data of RMS with ZYGO interferometer reached to 0.027λ(λ=0.6328μm).

  13. The Use and Maintenance of University Library Electronic Resources%浅议大学图书馆电子资源的利用与维护

    Institute of Scientific and Technical Information of China (English)

    马鹏飞; 熊豫玲

    2011-01-01

    随着科学技术的飞速发展,高新信息技术的广泛应用,大学图书馆的工作内容和方法也面临新的挑战,为了使用户更好的利用大学图书馆的电子资源,提高电子资源利用率,实现大学图书馆数字化,本文主要从电子资源的利用和维护方面进行探讨。%With the rapid development of science and technology,the extensive application of high-tech information technology, University of content and methods of library work is also facing new challenges in order to make better use of university library users to electronic resources,improve the utilization of electronic resources to achieve the University Library digital,paper, from the use of electronic resources and maintenance were discussed.

  14. Grinding behavior and surface appearance of (TiCp+TiBw)/Ti-6Al-4V titanium matrix composites

    Institute of Scientific and Technical Information of China (English)

    Ding Wenfeng; Zhao Biao; Xu Jiuhua; Yang Changyong; Fu Yucan; Su Honghua

    2014-01-01

    (TiCp+TiBw)/Ti-6Al-4V titanium matrix composites (PTMCs) have broad application prospects in the aviation and nuclear field. However, it is a typical difficult-to-cut material due to high hardness of the reinforcements, high strength and low thermal conductivity of Ti-6Al-4V alloy matrix. Grinding experiments with vitrified CBN wheels were conducted to analyze comparatively the grinding performance of PTMCs and Ti-6Al-4V alloy. Grinding force and force ratios, specific grinding energy, grinding temperature, surface roughness, ground surface appearance were dis-cussed. The results show that the normal grinding force and the force ratios of PTMCs are much larger than that of Ti-6Al-4V alloy. Low depth of cut and high workpiece speed are generally ben-eficial to achieve the precision ground surface for PTMCs. The hard reinforcements of PTMCs are mainly removed in the ductile mode during grinding. However, the removal phenomenon of the reinforcements due to brittle fracture still exists, which contributes to the lower specific grinding energy and grinding temperature of PTMCs than Ti-6Al-4V alloy.

  15. Research Progress of Interfacial Chemism of High Efficiency Organic Grinding Fluid for Si3N4 Ceramics

    Institute of Scientific and Technical Information of China (English)

    TIAN Xin-li; YANG Jun-fei; WU Zhi-yuan; HU Zhong-xiang

    2005-01-01

    Grinding is a most important machining method for Si3N4 ceramics. Utilizing interracial chemistry reac tion membrane between grinding fluid and Si3N4 ceramics can reduce friction factor, soften surface layer and meanwhile improve the grinding efficiency, which is a bran-new research direction. This article, based on high efficiency grinding of Si3N4 ceramics by the way of half plasticity removal, descanted on the assistant function of interface chemistry reaction to improve the removal rate of Si3N4 ceramics in the application of organic grinding fluids represented by alcohols grinding fluid. To target action mechanism research, it applies the methods of classification,comparison and induction, and advanced test equipments to explore the effects of long, short carbochain alcohol and their water solutions acting as grinding fluids. In addition, it also discusses the effective function of three groups of organic matters such as perhalogeno hydrocarbon, cationic surfactant and tetra ethoxysilane acting as grinding fluid components from different angles, reveals their mechanisms of action, and supplies theoretical basis for the development of machining ceramic grinding fluid of high efficiency, low cost.

  16. Surface quality prediction model of nano-composite ceramics in ultrasonic vibration-assisted ELID mirror grinding

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Bo; Chen, Fan; Jia, Xiao-feng; Zhao, Chong-yang; Wang, Xiao-bo [Henan Polytechnic University, Jiaozuo (China)

    2017-04-15

    Ultrasonic vibration-assisted Electrolytic in-process dressing (ELID) grinding is a highly efficient and highly precise machining method. The surface quality prediction model in ultrasonic vibration-assisted ELID mirror grinding was studied. First, the interaction between grits and workpiece surface was analyzed according to kinematic mechanics, and the surface roughness model was developed. The variations in surface roughness under different parameters was subsequently calculated and analyzed by MATLAB. Results indicate that compared with the ordinary ELID grinding, ultrasonic vibration-assisted ELID grinding is superior, because it has more stable and better surface quality and has an improved range of ductile machining.

  17. Knowledge acquirement in grinding process%磨削过程知识学习

    Institute of Scientific and Technical Information of China (English)

    吕长飞; 李郝林

    2012-01-01

    Buffing time and takt time in grinding process incarnated the grinding process parameters directly.Roughingprocess is the key of grinding and the rising part of acoustic emission signal curve in roughing process contains most abundant information.The fuzzy rule based on the triangular partition evenly was adapted for knowledge acquisition and learning process from the rising roughing part of grinding acoustic e-mission signal to establish corresponding relation between buffing time ,takt time and gradient of rising roughing part of grinding acoustic emission signal curve.Thus the gradient of rising roughing part of grinding acoustic emission signal curve corresponding to any buffing time and takt time is obtainetiln this way the rationality in selecting machining parameters could be estimated in order to select automatically and control intelligently the machining parameters in grinding process.Therefore the machining quality is ensured as well as on-line adjustment for machining parameters and intelligentized grinding in grinding process are realized.%磨削加工光磨时间、加工节拍直接体现磨削加工参数,粗磨过程的好坏是磨削过程的关键,磨削过程声发射信号粗磨段上升部分包含着磨削过程最丰富的信息,采用平均三角分配模糊规则对磨削过程声发射信号粗磨段上升部分进行知识获取和自学习,建立磨削加工光磨时间、加工节拍与磨削声发射曲线粗磨段上升部分斜率之间的对应关系,据此可得到任意光磨时间、加工节拍时对应的磨削声发射曲线粗磨段上升部分斜率.以此判断加工参数选择的合理性,以实现磨削加工的加工参数自动选择和智能控制,确保加工质量,实现磨削过程加工参数在线调整、磨削智能化.

  18. Barriers to electronic access and delivery of educational information in resource constrained public schools: a case of Greater Tubatse Municipality

    CSIR Research Space (South Africa)

    Pholotho, T

    2016-05-01

    Full Text Available Information and Communication Technologies (ICTs) are capable of expanding access to quality education, educational resources and provide teachers with new skills. Nevertheless, a majority of rural public schools have limited ICTs, mainly due...

  19. Electronic Grey Literature in Accelerator Science and Its Allied Subjects : Selected Web Resources for Scientists and Engineers

    CERN Document Server

    Rajendiran, P

    2006-01-01

    Grey literature Web resources in the field of accelerator science and its allied subjects are collected for the scientists and engineers of RRCAT (Raja Ramanna Centre for Advanced Technology). For definition purposes the different types of grey literature are described. The Web resources collected and compiled in this article (with an overview and link for each) specifically focus on technical reports, preprints or e-prints, which meet the main information needs of RRCAT users.

  20. 钢丝磨削试验研究%Steel Wire Grinding Test

    Institute of Scientific and Technical Information of China (English)

    李家春; 张萍

    2012-01-01

    砂带磨削作为一种新工艺,在机械加工领域发挥着越来越大的作用,满足了各种加工要求。本文简单介绍了砂带磨削的概念,阐述了一个针对钢丝表面除锈的新型砂带磨削设备的工作原理及其机床的主要机构,并通过试验研究磨削压力、金属去除率、砂带磨损、磨削比、磨削深度、钢丝走速之间的关系,为砂带修磨线材生产线提供了合理的磨削工艺参数。%As a new process, the abrasive belt grinding plays an increasingly important role in the field of machi- ning, which meets a variety of processing requirements. This paper introduces the concept of abrasive belt grinding briefly, describes the work principle of a new belt grinder to remove rust from the steel wire surface and the main structure of the device. Tests were conducted to study the relationships between grinding force, metal removal rate, belt wear rate, grinding ratio, grinding depth and wire walking speed, which provides rational parameters for wire snagging line with abrasive belt.

  1. Fundamental studies on enhancing heat transfer in contact zone during high efficiency grinding

    Institute of Scientific and Technical Information of China (English)

    XU; Hongjun(徐鸿钧); FU; Yucan(傅玉灿); XU; Xipeng(徐西鹏); XU; Xipeng

    2002-01-01

    On the basis of research on the thermal effect in grinding contact zone during high effi-ciency grinding, an idea of enhancing heat transfer in contact zone using high pressure water jetimpinging is advanced. Fundamental heat transfer experiments on enhancing heat transfer withhigh pressure water jet impinging were completed. The maximum speed of jet impinging reaches110m/s. The experimental results of transient and steady-state experiment prove that the criticalheat flux and the heat-transfer coefficient of water jet impinging are 70 and 30 times those of thepool boiling, respectively. Furthermore, a new grinding fluid supply system was employed to en-hance heat transfer in grinding zone by high-pressure water jet impingement during creep feedgrinding. The experimental results show that high-pressure water jet impinging has remarkablecooling effect. The temperature of the workpiece surface can be steadily kept below 100℃, whilethe workpiece is badly burnt with conventional coolant supply. The study will exploit an importantresearch orientation that has great potentialities in the high efficiency grinding. Further perfectionof this study will not only enable us to increase the available material removal rate to a new levelbut also solve the workpiece burn problem of the difficult-to-machining materials in high efficiencygrinding,

  2. 硬质合金刀具螺旋槽缓进给磨削力研究%Research on Grinding Forces of Creep Feed Grinding Cemented Carbide Tool Helical Grooves

    Institute of Scientific and Technical Information of China (English)

    宋铁军; 周志雄; 李伟; 任莹晖

    2014-01-01

    The grinding forces of creep feed grinding cemented carbide tool helical groove were an-alyzed by grinding wheel discretization method that the grinding wheel was regarded as composion of different elementary discs.Based on the grinding forces and torques of creep feed grinding cemented carbide tool helical groove,a mathematical model of grinding force ratio was established to describe the blunting of the diamond grains.The accurate signals of the grinding forces and torques were achieved by setting up a measurement system.The grinding force ratio was analyzed based on the mathematical model and the experimental data.The results show that the grinding force ratio can be used for grinding process evaluation.%用离散化方法将砂轮看作是由一组不同直径的单位厚度薄片组成的,分析了硬质合金刀具螺旋槽缓进给成形磨削的磨削力;基于工件轴向磨削力和力矩建立了一个表征砂轮锐利程度的磨削力比数学模型。通过建立的测力系统测量了螺旋槽缓进给磨削过程中轴向磨削力和力矩,并对其信号进行了分析。在理论和实验的基础上获得了两种磨削参数下的磨削力比。研究结果表明,磨削力比可作为硬质合金刀具螺旋槽缓进给磨削过程的评价参数。

  3. 电子资源许可使用的发展与创新%The Development and Innovation of the Use of the Electronic Resource License

    Institute of Scientific and Technical Information of China (English)

    王军

    2012-01-01

      电子资源许可使用在我国发展时间较短,在其建立过程中还存在许可定价、购买模式、馆际互借以及电子资源的长期保存许可方式等难题。电子资源许可使用的发展与创新,需要根据用户需求制定发展战略,建立图书馆的读者监督管理制度和数字化资源服务制度,规范文献编目制度等,以提高电子信息资源与图书馆信息资源的使用效果和广泛的使用需求%  It's been a short time since the use of electronic resource licenses has developed in China; in addition, many problems ap-pear in the establishment process in terms of license pricing, purchase pattern, inter-library loan and long-term preservation ways of electronic resources. In order to develop and innovate the use of the license, libraries should develop strategies in accordance with the users' needs, establish a reader supervision system and a digital resource service system, and normalize the document cataloging sys-tem to enhance the utilization effect and meet the extensive demand for electronic and library information resources.

  4. Occlusal splints for treating sleep bruxism (tooth grinding).

    Science.gov (United States)

    Macedo, C R; Silva, A B; Machado, M A; Saconato, H; Prado, G F

    2007-10-17

    Sleep bruxism is an oral activity characterised by teeth grinding or clenching during sleep. Several treatments for sleep bruxism have been proposed such as pharmacological, psychological, and dental. To evaluate the effectiveness of occlusal splints for the treatment of sleep bruxism with alternative interventions, placebo or no treatment. We searched the Cochrane Oral Health Group's Trials Register (to May 2007); the Cochrane Central Register of Controlled Trials (CENTRAL) (The Cochrane Library 2007, Issue 1); MEDLINE (1966 to May 2007); EMBASE (1980 to May 2007); LILACS (1982 to May 2007); Biblioteca Brasileira de Odontologia (1982 to May 2007); Dissertation, Theses and Abstracts (1981 to May 2007); and handsearched abstracts of particular importance to this review. Additional reports were identified from the reference lists of retrieved reports and from article reviews about treating sleep bruxism. There were no language restrictions. We selected randomised or quasi-randomised controlled trials (RCTs), in which splint therapy was compared concurrently to no treatment, other occlusal appliances, or any other intervention in participants with sleep bruxism. Data extraction was carried out independently and in duplicate. Validity assessment of the included trials was carried out at the same time as data extraction. Discrepancies were discussed and a third review author consulted. The author of the primary study was contacted when necessary. Thirty-two potentially relevant RCTs were identified. Twenty-four trials were excluded. Five RCTs were included. Occlusal splint was compared to: palatal splint, mandibular advancement device, transcutaneous electric nerve stimulation, and no treatment. There was just one common outcome (arousal index) which was combined in a meta-analysis. No statistically significant differences between the occlusal splint and control groups were found in the meta-analyses. There is not sufficient evidence to state that the occlusal splint is

  5. Ultra-fine grinding of silicate materials under the use of new resin bond diamond tools

    Science.gov (United States)

    Henkel, Sebastian; Bliedtner, Jens; Rädlein, Edda; Schulze, Christian; Rost, Matthias; Gerhardt, Martin; Fuhr, Michael

    2017-06-01

    The fabrication of high-quality optical components involves great effort. Polishing often functions as the final step in a manufacturing chain. To reduce the conventionally time-consuming, complex polishing process with loose grain, an interesting approach with novel resin bond grinding tools is presented for surface smoothing. Various processing-experiments were carried out, regarding different silicate materials such as BK7® and fused silica. Among other results it is shown, that good surface qualities with low roughness down to Ra = 8 nm or Rq = 10 nm can be achieved so far, a quality that already allows speaking of "ultra-fine" grinding. This results in remarkable possibilities to reduce conventional fine-machining procedures with loose abrasives. The fine grinded components can directly be polished to finally smooth the surface and remove remaining defects. Total-processing-times can be strongly reduced, involving significant economic advantages.

  6. Effect of Grinding Techniques on Absorbing Characteristics of Short Iron Fibers

    Institute of Scientific and Technical Information of China (English)

    2007-01-01

    Microwave-absorbing properties of iron fibers can be adjusted by their aspect ratio. This paper presents several modification techniques for grinding long iron fibers to a suitable aspect ratio. The grinding instruments include pulsator, jet mill and muller. The aspect ratio distribution, microstructure, electromagnetic parameter and refiectivity of the samples were analyzed and discussed in detail. The results show that the fractions of 5<aspect ratio<40 for the three methods are 69.03%, 81.11% and 80.2%, respectively, that is,suitable short iron fibers can be obtained by the jet mill and muller. Furthermore, the short iron fibers milled by jet mill and muller have better absorbing propterties than those obtained by the pulsator under the same condition. Therefore, their microwave absorption properties can be improved by regulating the electromagnetic parameters with grinding.

  7. The effect of moisture content on grinding process of wheat and maize single kernel

    Science.gov (United States)

    Lupu, M. I.; Pădureanu, V.; Canja, C. M.; Măzărel, A.

    2016-08-01

    The mechanical properties and the resistance of grains are key characteristics that enhance grinding behaviour of wheat and maize and are dependent on the moisture content of the grains. These properties were defined in the single-kernel compression test, and it seems that the qualities expressing the relations resulting during mechanical loads like mechanical and rheological properties are significant. The aim of the study reported here is to show the influence of moisture content on grinding process of wheat and maize single kernel. To show this influence it is necessary to study the physical and mechanical properties of wheat and maize single kernel at different moisture content 10%, 12%, 14%, 16%, 18% and 20%. The measurement results showed significant relationship between the cereal type, its resistance characteristics and the moisture content in the grinding process.

  8. Online monitoring of a belt grinding process by using a light scattering method

    Energy Technology Data Exchange (ETDEWEB)

    Boehm, Johannes; Vernes, Andras; Vorlaufer, Georg; Vellekoop, Michael

    2010-10-20

    Industrially ground surfaces often have a characteristic surface topography known as chatter marks. The surface finishing is mainly monitored by optical measurement techniques. In this work, the monitoring of an industrial belt grinding process with a light scattering sensor is presented. Although this technique is primarily applied for parametric surface roughness analysis, here it is shown that it enables also the measurement of the surface topography, i.e., the chatter marks occurring during the belt grinding process. In particular, it is proven that the light scattering method is appropriate to measure online the topography of chatter marks. Furthermore, the frequency analysis of the data reveals that the wavelength of chatter marks strongly depends on process parameters, such as the grinding speed.

  9. Rolling Resistance and Mechanical Properties of Grinded Copper Surfaces Using Molecular Dynamics Simulation

    Science.gov (United States)

    Liang, Shih-Wei; Wang, Chih-Hao; Fang, Te-Hua

    2016-09-01

    Mechanical properties of copper (Cu) film under grinding process were accomplished by molecular dynamics simulation. A numerical calculation was carried out to understand the distributions of atomic and slip vector inside the Cu films. In this study, the roller rotation velocity, temperature, and roller rotation direction change are investigated to clarify their effect on the deformation mechanism. The simulation results showed that the destruction of materials was increased proportionally to the roller rotation velocity. The machining process at higher temperature results in larger kinetic energy of atoms than lower temperature during the grinding process of the Cu films. The result also shows that the roller rotation in the counterclockwise direction had the better stability than the roller rotation in the clockwise direction due to significantly increased backfill atoms in the groove of the Cu film surface. Additionally, the effects of the rolling resistances on the Cu film surfaces during the grinding process are studied by the molecular dynamics simulation method.

  10. Rolling Resistance and Mechanical Properties of Grinded Copper Surfaces Using Molecular Dynamics Simulation.

    Science.gov (United States)

    Liang, Shih-Wei; Wang, Chih-Hao; Fang, Te-Hua

    2016-12-01

    Mechanical properties of copper (Cu) film under grinding process were accomplished by molecular dynamics simulation. A numerical calculation was carried out to understand the distributions of atomic and slip vector inside the Cu films. In this study, the roller rotation velocity, temperature, and roller rotation direction change are investigated to clarify their effect on the deformation mechanism. The simulation results showed that the destruction of materials was increased proportionally to the roller rotation velocity. The machining process at higher temperature results in larger kinetic energy of atoms than lower temperature during the grinding process of the Cu films. The result also shows that the roller rotation in the counterclockwise direction had the better stability than the roller rotation in the clockwise direction due to significantly increased backfill atoms in the groove of the Cu film surface. Additionally, the effects of the rolling resistances on the Cu film surfaces during the grinding process are studied by the molecular dynamics simulation method.

  11. Stress Analysis of a Three-Layer Metal Composite System of Bearing Assemblies During Grinding

    Science.gov (United States)

    Pashnyov, V. A.; Pimenov, D. Yu.

    2015-03-01

    A mathematical model of the stress state of a three-layer metal composite system caused by cutting forces during grinding the working layer of the system is elaborated. The implementation of the model by using the finite-element method made it possible to assess the effect of structure of the system, the deformation properties of layer materials, and grinding conditions on the distribution and level of normal and tangential stresses in layers, which determine the load-carrying capacity of the system. The results of an analysis of stress fields can serve as a basis for determining the grinding conditions ensuring retention of the load-carrying capacity of the metal composite system.

  12. Wheel wear and surface/subsurface qualities when precision grinding optical materials

    Science.gov (United States)

    Tonnellier, X.; Shore, P.; Luo, X.; Morantz, P.; Baldwin, A.; Evans, R.; Walker, D.

    2006-06-01

    An ultra precision large optics grinder, which will provide a rapid and economic solution for grinding large off-axis aspherical and free-form optical components, has been developed at Cranfield University. This paper presents representative grinding experiments performed on another machine - a 5 axes Edgetek - in order to verify the proposed BoX(r) grinding cycle. The optical materials assessed included; Zerodur(r), SIC and ULE(r), all three being materials are candidates for extreme large telescope (ELT) mirror segments. Investigated removal rates ranged from 2mm 3/s to 200mm 3/s. The higher removal rate ensures that a 1 metre size optic could be ground in less than 10 hours. These experiments point out the effect of diamond grit size on the surface quality and wheel wear. The power and forces for each material type at differing removal rates are presented, together with subsurface damage.

  13. Microwave-assisted grinding of metallurgical coke; Molienda asistida con microondas de un coque metalurgico

    Energy Technology Data Exchange (ETDEWEB)

    Ruisanchez, E.; Juarez-Perez, E. J.; Arenillas, A.; Bermudez, J. M.; Menendez, J. A.

    2014-10-01

    Metallurgical cokes are composed of graphitic carbon (s2p2) and different inorganic compounds with very different capacities to absorb microwave radiation. Moreover, due to the electric conductivity shown by the metallurgical cokes, microwave radiation produces electric arcs or microplasmas, which gives rise to hot spots. Therefore, when these cokes are irradiated with microwaves some parts of the particle experiment a rapid heating, while some others do not heat at all. As a result of the different expansion and stress caused by thermal the shock, small cracks and micro-fissures are produced in the particle. The weakening of the coke particles, and therefore an improvement of its grind ability, is produced. This paper studies the microwave-assisted grinding of metallurgical coke and evaluates the grinding improvement and energy saving. (Author)

  14. Extraction of Lithium from Lepidolite Using Mixed Grinding with Sodium Sulfide Followed by Water Leaching

    Directory of Open Access Journals (Sweden)

    Jaeryeong Lee

    2015-11-01

    Full Text Available Mixed grinding with Na2S followed by water leaching was performed to extract Li from lepidolite. The leachability of Li increases dramatically in the ground mixture, regardless of the mixing ratio over the range of 1:1 to 3:1, while only 4.53% of Li was extracted in lepidolite ground without Na2S. The leachability increased with an increase of the grinding time, and ultimately, 93% of the Li was leached by water from the ground mixture with a weight ratio of 3:1 (Na2S:Lepidolite. In the process of the mixed grinding, the Li-contained lepidolite was destructured crystallographically, and it might have changed to different compounds. This process enables us to extract Li from lepidolite via a water leaching treatment.

  15. Theoretical and experimental analysis on super precision grinding of monocrystal silicon

    Institute of Scientific and Technical Information of China (English)

    GUO Xiaoguang; GUO Dongming; KANG Renke; JIN Zhuji

    2007-01-01

    Through investigating the diamond-silicon grinding system,the grinding mechanism,including chip removal and subsurface damage,is discussed with the aid of the molecular dynamics(MD)approach and grinding experiments.Based on MD simulation,nanometric-grinding mechanism is analyzed from the viewpoint of instantaneous distribution of atoms,grinding force,and the potential energy between atoms and the profile of the groove.The simulation results show that some silicon atoms are deformed and piled up in front and on two sides of the abrasive surface because of the extrusion and cutting.When the energy in silicon lattice reaches its maximum value,the bonds of silicon atoms are broken and the material is removed.With the advancement of the abrasive,the silicon lattice under the abrasive surface is fractured,and then the amorphous layers are formed and propagated,which causes the subsurface damage.At the same time,some amorphous atoms are reconstructed and the degenerating layer of the machined surface is formed.Besides,the recovery of elatstic deformation occurs in the machined surface of the workpiece.In addition,the grinding experiment and profile detection with the aid of the measurment for 3D profiling are performed to verify the simulation results.The good agreement in the profile of the groove between the experimental value and the simulating value shows that MD simulation is very effective and reliable,and successful to fulfill the investigation on nanometric machining mechanism.

  16. Simulation and Experimental Analysis of Super High-Speed Grinding of Ductile Material

    Institute of Scientific and Technical Information of China (English)

    SHIMIZU; Jun; EDA; Hiroshi

    2002-01-01

    This study aims to reduce the work-affected layer of the machined surface by carrying out the grinding at the speed over static pr o pagation speed of plastic wave of ductile materials and also aims to clarify suc h super high-speed machining mechanism.This paper reports on the result obtain ed through the molecular dynamics simulations and experiments on the super-spee d grinding below and beyond static propagation speed of aluminum.From the simul ation results,it is verified that the plastic deformation ...

  17. Development of a Wire Driven Robot for Grinding with Stiffness Adapted

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Along with development of new design and machining me thod production with more complex surface can be manufactured. Researching on th e new equipment used for surface disposal has become the important matter. Grind ing and polishing are a common surface processing method. A new type wire driven parallel robot used for grinding processing is proposed in this paper. Wire driven parallel robot is developed from parallel robot and serial wire driven r obot. Steel wire is used to replace the leg of paralle...

  18. A Facile Solvent Free Synthesis of 3-arylidenechroman-4-ones Using Grinding Technique

    Directory of Open Access Journals (Sweden)

    Suresh Kumar

    2012-01-01

    Full Text Available An efficient method for the synthesis of 3-arylidenechroman-4-ones has been developed under solvent free conditions using grinding technique. Grinding of variously substituted chroman-4-ones with aromatic aldehydes in presence of anhydrous barium hydroxide at room temperature give 3-arylidenechroman-4-ones in high yield (75-92%. Products are obtained by just acidification of the reaction mixture in ice cold water. Reaction in solid state, with enhanced rate, high selectivity and manipulative simplicity are the attractive features of this environmentally benign protocol. The chroman-4-one derivatives required for the reaction have been obtained by polyphosphoric acid (PPA catalysed cyclisation of phenoxypropanoic acids under microwave irradiations.

  19. INFLUENCE OF OSCILLATORY IMPACT ON MOVEMENT IN LIQUID AND GRINDING OF WOOD PULP USED FOR PACKAGING PRODUCTION

    Directory of Open Access Journals (Sweden)

    I. I. Karpunin

    2011-01-01

    Full Text Available The paper investigates an influence of oscillatory impacts on wood pulp grinding which is used for packaging production.It has been established that plate oscillatory impact promotes better quality of the obtained paper sheet made of grind plant fiber.

  20. THEORETICAL AND EXPERIMENTAL STUDIES OF ENERGY-EFFICIENT GRINDING PROCESS OF CEMENT CLINKER IN A BALL MILL

    Directory of Open Access Journals (Sweden)

    Kuznetsova M.M.

    2014-08-01

    Full Text Available The article presents results of theoretical and experimental research of grinding process of bulk materials in a ball mill. The new method of determination of energy efficiently mode of operation of ball mills in a process of a cement clinker grinding is proposed and experimentally tested.

  1. Study on cermet CBN grinding wheels for ultra-precision grinding%一种新型超精磨金属陶瓷CBN砂轮的研究

    Institute of Scientific and Technical Information of China (English)

    陈卫东; 韩云

    2012-01-01

    通过考察不同因素对砂轮锋利性、寿命及加工工件表面粗糙度的影响,优选出了端面超精磨CBN砂轮的制备工艺.通过对比实验,得出最优配比如下:CBN磨料的粒径优选添加40 μm,陶瓷空心球的粒度优选添加240目,其添加量优选体积分数为20%,金属粉的优选体积分数为9%.该配方制备的CBN砂轮的锋利性、寿命及加工工件的表面粗糙度均达到了较好的效果.%By studying main influence factors on wheel sharpness, lifetime and machined surface roughness of workpieces, optimum manufacturing technology of cermet CBN grinding wheel for end ultra-precision grinding was researched. After a series of comparative experiments, optimized manufacturing parameters were obtained as follows; particle size of CBN grits 40 μm; hollow ceramic sphere size 240 meshes with addition amount 20% (volume fraction) ; and volume fraction of metal powder 9%. CBN grinding wheels prepared according to the formula above showed better properties, such as sharpness, lifespan and surface roughness of machined workpieces.

  2. Clinician‐selected Electronic Information Resources do not Guarantee Accuracy in Answering Primary Care Physicians’ Information Needs. A review of: McKibbon, K. Ann, and Douglas B. Fridsma. “Effectiveness of Clinician‐selected Electronic Information Resources for Answering Primary Care Physicians’ Information Needs.” Journal of the American Medical Informatics Association 13.6 (2006: 653‐9.

    Directory of Open Access Journals (Sweden)

    Martha Ingrid Preddie

    2008-03-01

    Full Text Available Objective – To determine if electronic information resources selected by primary care physicians improve their ability to answer simulated clinical questions.Design – An observational study utilizing hour‐long interviews and think‐aloud protocols.Setting – The offices and clinics of primary care physicians in Canada and the United States.Subjects – Twenty‐five primary care physicians of whom 4 were women, 17 were from Canada, 22 were family physicians,and 24 were board certified.Methods – Participants provided responses to 23 multiple‐choice questions. Each physician then chose two questions and looked for the answers utilizing information resources of their own choice. The search processes, chosen resources and search times were noted. These were analyzed along with data on the accuracy of the answers and certainties related to the answer to each clinical question prior to the search.Main results – Twenty‐three physicians sought answers to 46 simulated clinical questions. Utilizing only electronic information resources, physicians spent a mean of 13.0 (SD 5.5 minutes searching for answers to the questions, an average of 7.3(SD 4.0 minutes for the first question and 5.8 (SD 2.2 minutes to answer the second question. On average, 1.8 resources were utilized per question. Resources that summarized information, such as the Cochrane Database of Systematic Reviews, UpToDate and Clinical Evidence, were favored 39.2% of the time, MEDLINE (Ovid and PubMed 35.7%, and Internet resources including Google 22.6%. Almost 50% of the search and retrieval strategies were keyword‐based, while MeSH, subheadings and limiting were used less frequently. On average, before searching physicians answered 10 of 23 (43.5% questions accurately. For questions that were searched using clinician‐selected electronic resources, 18 (39.1% of the 46 answers were accurate before searching, while 19 (42.1% were accurate after searching. The difference of

  3. Effect of Grinding and Polishing on the Residual Stress and Bending Strength of a Silicon Nitride Ceramic

    Institute of Scientific and Technical Information of China (English)

    GAO Ling; YANG Haitao; DU Daming; ZHAO Shikun; LI Huaping; YUAN Runzhang

    2005-01-01

    The residual stresses on the surface of the differently ground and polished silicon nitride ceramics were measured using X-ray diffraction and identified by SEM.The effect of the residual stress on the bending strength was investigated.The investigations show that the grinding process can introduce subatantial tensile residual stresses up to 290MPa on the surface of silicon nitride ceramics,which has a significant effect on reducing the bending strength of the ceramics after grinding.Thus,in comparison with the ceramics with a rough surface,the ceramics with a mirror image surface may have a lower strength.Polishing can smooth the residual stresses.When we evaluate the quality of the ceramic components after grinding,we must take residual stress into consideration. The grinding methods and grinding conditions must be carefully selected in order to get the favorite residual stress as well as the surface smoothness.

  4. Conceived on the City Electronic Waste Resource Mana oement Model%城市电子废弃物资源化管理模式构想

    Institute of Scientific and Technical Information of China (English)

    熊贵琍; 余涛

    2012-01-01

    Investigated e- waste collection system the investigation, the whereabouts and electronic waste disposal in Httizhou city, the paper analyzed the Huizhou city e- waste collection and disposal of a series of problems, combined with the actual, conceived urban electronic waste resources management mode.%通过对惠州市电子废弃物收集体系组成、去向以及电子废弃物处置方式的调查,分析惠州市电子废弃物收集和处置存在的一系列问题,结合实际提出了城市电子废弃物资源化管理模式的初步构想。

  5. Accessibility and Use of Web-Based Electronic Resources by Physicians in a Psychiatric Institution in Nigeria

    Science.gov (United States)

    Oduwole, Adebambo Adewale; Oyewumi, Olatundun

    2010-01-01

    Purpose: This study aims to examine the accessibility and use of web-based electronic databases on the Health InterNetwork Access to Research Initiative (HINARI) portal by physicians in the Neuropsychiatric Hospital, Aro--a psychiatry health institution in Nigeria. Design/methodology/approach: Collection of data was through the use of a three-part…

  6. Effect of ultrafine grinding on physicochemical and antioxidant properties of dietary fiber from wine grape pomace.

    Science.gov (United States)

    Zhu, Feng-Mei; Du, Bin; Li, Jun

    2014-01-01

    Wine grape pomace dietary fiber powders were prepared by superfine grinding, whose effects were investigated on the composition, functional and antioxidant properties of the wine grape pomace dietary fiber products. The results showed that superfine grinding could effectively pulverize the fiber particles to submicron scale. As particle size decrease, the functional properties (water-holding capacity, water-retention capacity, swelling capacity, oil-binding capacity, and nitrite ion absorption capacity) of wine grape pomace dietary fiber were significantly (p fiber components from insoluble to soluble fractions was observed. The antioxidant activities of wine grape pomace and dietary fiber before and after grinding were in terms of DPPH radical scavenging activity, ABTS diammonium salt radical scavenging activity, ferric reducing antioxidant power, and total phenolic content. Compared with dietary fiber before and after grinding, micronized insoluble dietary fiber showed increased ABTS radical scavenging activity, ferric reducing antioxidant power, and total phenolic content yet decreased DPPH radical scavenging activity. Positive correlations were detected between ABTS radical scavenging activity, ferric reducing antioxidant power, and total phenolic content.

  7. Synthesis of bimetallic gold-silver alloy nanoclusters by simple mortar grinding.

    Science.gov (United States)

    Murugadoss, Arumugam; Kai, Noriko; Sakurai, Hidehiro

    2012-02-21

    A macroscale quantity of bimetallic Au-Ag alloy nanoclusters was achieved through sequential reduction by simple mortar grinding. The chitosan biopolymer was used as both a stabilizing and reducing agent. These nanoclusters exhibit excellent catalytic activity toward the reduction of 4-nitrophenol.

  8. Determining the optimum process parameter for grinding operations using robust process

    Energy Technology Data Exchange (ETDEWEB)

    Neseli, Suley Man; Asilturk, Ilhan; Celik, Levent [Univ. of Selcuk, Konya (Turkmenistan)

    2012-11-15

    We applied combined response surface methodology (RSM) and Taguchi methodology (TM) to determine optimum parameters for minimum surface roughness (Ra) and vibration (Vb) in external cylindrical grinding. First, an experiment was conducted in a CNC cylindrical grinding machine. The TM using L{sup 27} orthogonal array was applied to the design of the experiment. The three input parameters were workpiece revolution, feed rate and depth of cut; the outputs were vibrations and surface roughness. Second, to minimize wheel vibration and surface roughness, two optimized models were developed using computer aided single objective optimization. The experimental and statistical results revealed that the most significant grinding parameter for surface roughness and vibration is workpiece revolution followed by the depth of cut. The predicted values and measured values were fairly close, which indicates 2 ( 94.99 R{sup 2Ra}=and 2 92.73) R{sup 2Vb}=that the developed models can be effectively used to predict surface roughness and vibration in the grinding. The established model for determination of optimal operating conditions shows that a hybrid approach can lead to success of a robust process.

  9. Kinematic equations to grind a helical drill point on a virtual axis drill sharpener

    Institute of Scientific and Technical Information of China (English)

    陈五一; 陈鼎昌

    2000-01-01

    The basic structure of a virtual axis drill grinder is presented in terms of the spatial vectors and thegrinding parameters calculated according to the geometry of a helical drill point. The kinematic equations for sharpening the drills on the virtual axis grinder are deduced using the grinding parameters via vector-matrix txansformation.

  10. Mist-jetting Electrical Discharge Dressing Technology for Superabrasive Grinding Wheels

    Institute of Scientific and Technical Information of China (English)

    CAI Lan-rong; HU De-jin; JIA yan

    2008-01-01

    The technology of superabrasive grinding has been developed in order to achieve high-quality finish in extremely hard and brittle materials.Thereafter,truing and dressing technology on super abrasive grinding wheel is one of the most important subjects on precise machining field at present.In this paper,mist-jetting electrical discharge technology was applied to dressing metai-bonded superabrasive wheels.And a systematical study on the mechanism of selective removal of the bond was proposed.Experiments on dressing bronze bonded diamond grind wheels were carried out on a die-sinking electrical discharge machine.The diamond wheel topographies before and after electrical discharge dressing were observed by VH-800 3D digital microscope.The wheel profiles before and after dressing were observed.The results of electrical discharge dressing under different electrical parameters were compared.Experimental results indicate that the favorable surface topography can be obtained under suitable processing parameters and mist-jetting electrical discharge dressing (MEDD) is feasible for metal-bonded diamond grinding wheel.

  11. Determination of the scheme of precision grinding compensation on the radome

    Institute of Scientific and Technical Information of China (English)

    GUO Dongming; LIU Minjing; ZHANG Chunbo; SHENG Xianjun; SUN Yuwen

    2007-01-01

    The radome,which is often used to house airborne scanning radar antennas,causes a large boresight error and boresight error slope of the radar antenna.One way to decrease the boresight error induced by the radome is to modify its geometric thickness.Determining the grinding scheme from the boresight error performance is the most important problem to be solved.A typical inverse problem about electromagnetic fields is solving the precise grinding compensation area and allowance according to the antenna aperture distribution and the radome's boresight error performance,which could hardly be solved by a purely mathematical method.An effective approach combining theoretical analysis and mathematical calculations with experimental measurement is presented in this paper to determine the grinding area and allowance for compensating the boresight error performance of the radome.By comparing the calculated and measured data of the boresight error and the boresight error slope before and after grinding,it is shown that this method is simple and practical and can be used for many kinds of radomes.

  12. Experimental Analysis & Optimization of Cylindirical Grinding Process Parameters on Surface Roughness of En15AM Steel

    Directory of Open Access Journals (Sweden)

    Sandeep Kumar

    2015-07-01

    Full Text Available As per the modern Industrial requirements, higher surface finish mechanical components and mating parts with close limits and tolerances, is one of the most important requirement. Abrasive machining processes are generally the last operations performed on manufactured products for higher surface finishing and for fine or small scale material removal. Higher surface finish and high rate of removal can be obtained if a large number of grains act together. This is accomplished by using bonded abrasives as in grinding wheel or by modern machining processes. In the present study, Taguchi method or Design of experiments has been used to optimize the effect of cylindrical grinding parameters such as wheel speed (rpm, work speed, feed (mm/min., depth of cut and cutting fluid on the surface roughness of EN15AM steel. Ground surface roughness measurements were carried out by Talysurf surface roughness tester. EN15AM steel has several industrial applications in manufacturing of engine shafts, connecting rods, spindles, studs, bolt, screws etc. The results indicated that grinding wheel speed, work piece speed, table feed rate and depth of cut were the significant factors for the surface roughness and material removal rate. Surface roughness is minimum at 2000 r.p.m. of grinding wheel speed , work piece speed 80 rpm, feed rate 275 mm/min. and 0.06 mm depth of cut.

  13. Single Side Electrolytic In-Process Dressing (ELID) Grinding with Lapping Kinematics of Silicon Carbide

    Science.gov (United States)

    Khoshaim, Ahmed Bakr

    The demand for Silicon Carbide ceramics (SiC) has increased significantly in the last decade due to its reliable physical and chemical properties. The silicon carbide is widely used for aerospace segments in addition to many uses in the industry. Sometimes, a single side grinding is preferable than conventional grinding, for it has the ability to produce flat ceramics. However, the manufacturing cost is still high because of the high tool wear and long machining time. Part of the solution is to use electrolytic in process dressing (ELID) to reduce the processing time. The study on ELID single side grinding of ceramics has never been attempted before. The study involves four variables with three levels each. One of the variables, which is the eccentricity, is being investigated for the first time on ceramics. A full factorial design, for both the surface roughness and material removal rate, guides to calculate mathematical models that can predict future results. Three grinding wheel mesh sizes are used. An investigation of the influence of different grain size on the results can then be evaluated. The kinematics of the process was studied based on eccentricity in order to optimize the pattern of the diamond grains. The experiment is performed with the assist of the proposed specialized ELID fluid, TRIM C270E.

  14. New technique for preparing cartilage for intracordal injection: the freezing and grinding method.

    Science.gov (United States)

    Park, Young Min; Lee, Won Yong; Lim, Yun-Sung; Lee, Jin-Choon; Lee, Byung-Joo; Wang, Soo-Geun

    2014-07-01

    We developed a technique for preparing harvested cartilage that creates finer, more uniform pieces by freezing with liquid nitrogen and grinding with a mortar and pestle. Herein, we report the application of this new technique for intracordal cartilage injection. Experimental study. Human cartilage was obtained from surgical cases. In the standard method, harvested cartilage was prepared with scissors and a knife. In the experimental group, harvested cartilage was frozen with liquid nitrogen and ground with a mortar and pestle. It took an average of 60 minutes to manipulate cartilage using the standard technique, whereas it took an average of 10 minutes using the freezing and grinding method (P<0.001). The average size of cartilage flakes generated by the standard and new techniques were 727 and 48.6 μm, respectively. The cartilage flakes produced using scissors and a knife were able to pass through a 19-gauge needle, whereas those created using the freezing and grinding method were able to pass through a 24-gauge needle. Using the freezing and grinding method, cartilage was broken into fine, uniform pieces that could pass through a 24-gauge needle. This new technique will facilitate the production of commercial cartilage material for intracordal injection. Copyright © 2014 The Voice Foundation. All rights reserved.

  15. STIMULATION OF PROCESS OF MUNERAL POWDER GRINDING THROUGH INTRODUCTION OF ADMIXTURES

    Directory of Open Access Journals (Sweden)

    Tarasov Roman Viktorovich

    2012-10-01

    Full Text Available The status of nanotechnologies in material science predetermines development of nanotechnology-intensive products that demonstrate pre-set properties of modified materials. The presence of nano-size particles of substances makes it possible to benefit from their physical and chemical potential and to overcome some negative developments that accompany the structure formation process (at interphase boundaries. The barrier properties are variable, which is quite important in terms of the increase of the asphalt concrete durability. Production of a modifier (that has nano-particles of the pre-set chemical composition to be added into asphalt concrete mixes is also of interest. The authors present their findings concerning the nano-scale modifier that has a chemically inert component and a hydraulically active substance. The method of de-aggregation is used to produce the nano-scale modifier. By-products are often welcomed as mineral components of the asphalt concrete, as they reduce its cost. The findings of the authors concerning the influence of the grinding mode on the integrated characteristics of the powder are presented in the paper. It is proven than dependence of integrated dispersion indicators is nonlinear due to processes leading to aggregation of mineral powder particles. The analysis of the experimental data collected in the course of "wet" grinding proves that surface-active substances stimulate the process of grinding. The type and concentration of an additive that improves the grinding efficiency is also identified.

  16. Robustness of a cross contamination model describing transfer of pathogens during grinding of meat

    DEFF Research Database (Denmark)

    Møller, Cleide Oliveira de Almeida; Sant’Ana, A. S.; Hansen, Solvej Katrine Holm

    2016-01-01

    This study aimed to evaluate a cross contamination model for its capability of describing transfer of Salmonella spp. and L. monocytogenes during grinding of varying sizes and numbers of pieces of meats in two grinder systems. Data from 19 trials were collected. Three evaluation approaches were...

  17. Robustness of a cross contamination model describing transfer of pathogens during grinding of meat

    DEFF Research Database (Denmark)

    Møller, Cleide Oliveira de Almeida; Sant’Ana, A. S.; Hansen, Solvej Katrine Holm

    2016-01-01

    This study aimed to evaluate a cross contamination model for its capability of describing transfer of Salmonella spp. and L. monocytogenes during grinding of varying sizes and numbers of pieces of meats in two grinder systems. Data from 19 trials were collected. Three evaluation approaches were...

  18. Ultra-precision ductile grinding of BK7 using super abrasive diamond wheel

    Institute of Scientific and Technical Information of China (English)

    ZHAO Qingliang; Brinksmeier Ekkard; Riemer Oltmann; Rickens Kai

    2007-01-01

    In this paper,a novel conditioning technique using copper bonded diamond grinding wheels of 91 μm grain size and electrolytic in-process dressing (ELID) is first developed to precisely and effectively condition a nickelelectroplated monolayer coarse-grained diamond grinding wheel of 151 μm grain size.Under optimised conditioning parameters,the super abrasive diamond wheel was well conditioned in terms of a minimized run-out error and flattened diamond grain surfaces of constant peripheral envelope.The conditioning force was monitored by a force transducer,while the modified wheel surface status was in-situ monitored by a coaxial optical distance measurement system.Finally,the grinding experiment on BK7 was conducted using the well-conditioned wheel with the corresponding surface morphology and subsurface damage measured by atomic force microscope (AFM) and scanning electric microscope (SEM),respectively.The experimental result shows that the newly developed conditioning technique is applicable and feasible to ductile grinding optical glass featuring nano scale surface roughness,indicating the potential of super abrasive diamond wheels in ductile machining brittle materials.

  19. DRY AND WET GRINDING KINETICS OF CHROMIUM ORE AND EFFECT OF PULP DENSITY

    Directory of Open Access Journals (Sweden)

    Alper ÖZKAN

    2006-01-01

    Full Text Available In this study, the kinetics of dry and wet grinding of various feed sizes of chromium ore has been determined using a laboratory scale ceramic ball mill. In addition, the effect of pulp density on the spesific rate of breakage (Si and net production rate to finer than specified size were investigated. The dry and wet grinding of all the size intervals of chromium ore followed the first-order breakage law, and the Si values increased as the feed sizes became coarser. Moreover, the wet grinding of these various feed sizes gave higher Si values by a factor of 2.0 to 2.6 comparing to the dry Si values. From the experimental studies performed on the effect of pulp density on the grinding process, the highest Si value was obtained at a pulp density of 45 % solids by volume. At the same pulp density value, the rate of net production of -75 µm particle size also reached the highest value.

  20. Fatigue Behavior of Friction Stir-Welded Joints Repaired by Grinding

    Science.gov (United States)

    Vidal, C.; Infante, V.

    2014-04-01

    Fatigue is undoubtedly the most important design criterion in aeronautic structures. Although friction stir-welded joints are characterized by a high mechanical performance, they can enclose some defects, especially in their root. These defects along with the relatively low residual stresses of the friction stir-welding thermomechanical cycle can turn into primary sources of crack initiation. In this context, this article deals with the fatigue behavior of friction stir-welded joints subjected to surface smoothing by grinding improvement technique. The 4-mm-thick aluminum alloy 2024-T351 was used in this study. The fatigue strength of the base material, joints in the as-welded condition, and the sound and defective friction stir-welded joints improved by grinding were investigated in detail. The tests were carried out with a constant amplitude loading and with a stress ratio of R = 0. The fatigue results show that an improvement in fatigue behavior was obtained in the joints repaired by superficial grinding technique. The weld grinding technique is better especially for lower loads and increases the high cycle fatigue strength. The fatigue strength of the improved welded joints was higher than that of the base material.

  1. Investigation on the potential of waste cooking oil as a grinding aid in Portland cement.

    Science.gov (United States)

    Li, Haoxin; Zhao, Jianfeng; Huang, Yuyan; Jiang, Zhengwu; Yang, Xiaojie; Yang, Zhenghong; Chen, Qing

    2016-12-15

    Although there are several methods for managing waste cooking oil (WCO), a significant result has not been achieved in China. A new method is required for safe WCO management that minimizes the environmental threat. In this context, this work was developed in which cement clinker and gypsum were interground with various WCOs, and their properties, such as grindability, water-cement ratio required to achieve a normal consistency, setting times, compressive strength, contents of calcium hydroxide and ettringite in the hardened paste, microstructure and economic and environmental considerations, were addressed in detail. The results show that, overall, WCO favorably improves cement grinding. WCO prolonged the cement setting times and resulted in longer setting times. Additionally, more remarkable effects were found in cements in which WCO contained more unsaturated fatty acid. WCOs increased the cement strength. However, this enhancement was rated with respect to the WCO contents and components. WCOs decreased the CH and AFt contents in the cement hardened paste. Even the AFt content at later ages was reduced when WCO was used. WCO also densify microstructure of the hardened cement paste. It is economically and environmentally feasible to use WCOs as grinding aids in the cement grinding process. These results contribute to the application of WCOs as grinding aids and to the safe management of WCO. Copyright © 2016 Elsevier Ltd. All rights reserved.

  2. Electrophoretic deposition grinding (EPDG) for improving the precision of microholes drilled via ECDM

    Science.gov (United States)

    Yan, Biing-Hwa; Yang, Ching-Tang; Huang, Fuang-Yuan; Lu, Zhe-Hong

    2007-02-01

    Electrochemical discharge machining (ECDM) is an alternative method to microdrill Pyrex glass for MEMS devices. However, the taper and the heat-affected zone of the microholes resulting from the thermal energy is a problem to which attention has to be paid. This study attempts to improve the ECDMed microhole quality by applying electrophoretic deposition grinding (EPDG). ECDM was first used to drill a microhole and was followed by EPDG to refine the hole. The experimental results demonstrated that selecting a suitable diameter of the tool in EPDG is important to improve the taper angle of microholes machined by ECDM. A step shape tool with phi210 µm diameter was designed as a critical factor for improving the taper. An excellent taper angle of 0.2° could be achieved. At the beginning of EPDG, the taper angle and wavy surface of the ECDMed hole were improved by the step shape tool. The subsequent EPDG further improved the surface roughness. Additionally, a sufficient grinding time was required to produce a fine surface. Improving surface roughness requires a higher tool rotation speed and a longer grinding time. However, the dislodging of abrasives in the entrance will worsen the roundness and increase the diameter difference of the hole. Suitable grinding parameters for use in the experiments include tool rotation speed: 1500 rpm, abrasive size: 0.3 µm and grinding time: 500 s. After EPDG, the surface roughness of the microholes achieved was 5 nm Ra. This study demonstrates the feasibility of using EPDG to improve the quality of the ECDMed hole.

  3. Anterior temporalis and suprahyoid EMG activity during jaw clenching and tooth grinding.

    Science.gov (United States)

    Aldana, Karina; Miralles, Rodolfo; Fuentes, Aler; Valenzuela, Saúl; Fresno, María Javiera; Santander, Hugo; Gutiérrez, Mario Felipe

    2011-10-01

    The aim of this study was to evaluate the anterior temporalis and suprahyoid electromyographic (EMG) activity during jaw clenching and tooth grinding at different jaw posture tasks. The study included 30 healthy subjects with natural dentition and bilateral molar support, incisive protrusive guidance and bilateral laterotrusive canine guidance. Bipolar surface electrodes were located on the right anterior temporalis and suprahyoid muscles. Three EMG recordings in the standing position were performed in the following tasks: C. clenching in the intercuspal position (IP); P1. eccentric grinding from IP to protrusive edge-to-edge contact position; P2. clenching in protrusive edge-to-edge contact position; P3. concentric grinding from protrusive edge-to-edge contact position to IP; L1. eccentric grinding from IP to laterotrusive edge-to-edge contact position; L2. clenching in laterotrusive edge-to-edge contact position; L3. concentric grinding from laterotrusive edge-to-edge contact position to IP. EMG activity during protrusive and laterotrusive tasks was lower than intercuspal position in the anterior temporalis, whereas an opposite EMG pattern was observed in the suprahyoid muscles activity, excepting recorded activity in L2 (mixed model with unstructured covariance matrix). Anterior temporalis activity was higher during P3 than P1 and P2 tasks and during L3 than L1 and L2 tasks, whereas in the suprahyoid muscles, activity was higher during P1 than P2 tasks and during L1 than L2 and L3 tasks. These results could support the idea of a differential modulation of the motor neuron pools of anterior temporalis and suprahyoid muscles of peripheral and/or central origin.

  4. Automatic detection of thermal damage in grinding process by artificial neural network

    Directory of Open Access Journals (Sweden)

    Fábio Romano Lofrano Dotto

    2003-12-01

    Full Text Available This work aims to develop an intelligent system for detecting the workpiece burn in the surface grinding process by utilizing a multi-perceptron neural network trained to generalize the process and, in turn, obtnaing the burning threshold. In general, the burning occurrence in grinding process can be detected by the DPO and FKS parameters. However, these ones were not efficient at the grinding conditions used in this work. Acoustic emission and electric power of the grinding wheel drive motor are the input variable and the output variable is the burning occurrence to the neural network. In the experimental work was employed one type of steel (ABNT-1045 annealed and one type of grinding wheel referred to as TARGA model ART 3TG80.3 NVHB.Esse trabalho tem por objetivo o desenvolvimento de um sistema inteligente para detecção da queima no processo de retificação tangencial plana através da utilização de uma rede neural perceptron multi camadas, treinada para generalizar o processo e, conseqüentemente, obter o limiar de queima. Em geral, a ocorrência da queima no processo de retificação pode ser detectada pelos parâmetros DPO e FKS. Porém esses parâmetros não são eficientes nas condições de usinagem usadas nesse trabalho. Os sinais de emissão acústica e potência elétrica do motor de acionamento do rebolo são variáveis de entrada e a variável de saída é a ocorrência da queima. No trabalho experimental, foram empregados um tipo de aço (ABNT 1045 temperado e um tipo de rebolo denominado TARGA, modelo ART 3TG80.3 NVHB.

  5. Surface quality of a 1m Zerodur part using an effective grinding mode

    Science.gov (United States)

    Tonnellier, X.; Shore, P.; Morantz, P.; Orton, D.

    2008-09-01

    A new ultra precision large optics grinding machine, BoX (R) , has been developed at Cranfield University. This machine is located at the UK's Ultra Precision Surfaces laboratory at the OpTIC Technium, North Wales. This machine offers a rapid and economic solution for grinding large off-axis aspherical and free-form optical components. This paper presents an analysis of surface and subsurface damage assessments of Zerodur(R) ground using diamond resin bonded grinding wheels. Zerodur(R) was tested as it is one of the materials currently under study for making extremely large telescope (ELT) segmented mirrors such as in the E-ELT project. The grinding experiments have been conducted on the BoX(R) grinding machine using wheels with grit sizes of 76 μm, 46 µm and 25 μm. The highest material removal rate (187.5 mm3/s) used ensures that a 1 metre diameter optic can be ground in less than 10 hours. The surface roughness and surface profile were measured using a Form Talysurf. The subsurface damage was revealed using a sub aperture polishing process in combination with an etching technique on small parts. These results are compared with the targeted form accuracy of 1 μm p-v over a 1 metre part, surface roughness of 50-150 nm RMS and subsurface damage in the range of 2-5 μm. This process stage was validated on a 1 metre hexagonal Zerodur(R) part.

  6. Ibuprofen-Amino Acids Co-Crystal Screening Via Co-Grinding Methods

    Directory of Open Access Journals (Sweden)

    Othman Muhamad Fitri

    2016-01-01

    Full Text Available The importance of pharmaceutical co-crystals now has been recognized in order to improve the research and development in pharmaceutical industries. Low solubility of active pharmaceutical ingredient (API has led to the growth of new pharmaceutical co-crystals formation as it enhances the physicochemical properties of the API. In this works, preparation of new co-crystal formation between ibuprofen (IBP with selected amino acid compounds were performed by using dry grinding and liquid assisted grinding (LAG techniques. Ibuprofen (IBP was selected as the API meanwhile glycine (GLY, L-alanine (ALA and L-proline (PRO were selected as co-crystal former (CCF agents. The products of IBP-co-former from grinding experiments for the formation of co-crystals were characterized and verified using X-Ray Powder Diffraction (XRPD, Differential Scanning Calorimetry (DSC and Fourier Transform Infra-Red Spectroscopy (FTIR. The finding reveals that the IBP-PRO co-crystals have successfully formed. For IBP-PRO system, new crystalline peaks from XRPD were recorded at 2θ values of 4.374°, 5.436° and 10.944° from dry grinding technique and 4.41°, 5.436° and 10.962° for liquid assisted grinding (LAG technique. A new melting point of 257.49 °C was discovered for IBP-ALA indicates the possibility of co-crystals formation. On the other hand, the analysis for IBP-GLY shows that no co-crystals formed in the system.

  7. Effect of grinding wheel granularity on the grinding-hardened layer of 42CrMo steel%砂轮粒度对42CrMo钢磨削强化层的影响

    Institute of Scientific and Technical Information of China (English)

    时海芳; 刘波; 马壮; 刘克铭

    2011-01-01

    在精密卧式磨床M7132A上,利用磨削加工产生的大量磨削热对磨削加工表面进行淬火处理.采用砂轮作为磨削淬火的加工工具,研究不同粒度的刚玉砂轮对42CrMo钢进行磨削淬火试验及强化层的组织和硬度的影响.结果表明:随着砂轮粒度的减小,距加工表面的强化层组织越细小;强化层的显微硬度分布曲线基本相同,但是距强化层至加工表面0.25 mm时,随着砂轮粒度的减小,强化层显微硬度增大,磨削强化层厚度增加.%Grinding heat generated from grinding was used to do hardening treatment for grinding machining surface on horizontal precision grinder (M7132A). The grinding wheel was used as grind-hardening machining tool to study the influence of grinding wheel granularity on microstructure and hardness of strengthened layer of 42CrMo. The results show that with the decrease of the particle size of grinding wheel, microstructure of strengthened layer on machined surface is fine. The microhardness distribution curve of strengthened layer is basicly same, but when the strengthened layer is 0.25 mm away from the machined surface, the decrease of particle size of grinding wheel will lead to the increase of microhardness of strengthened layer. Thickness of the grinding-strengthened layer increases.

  8. Share and share alike: encouraging the reuse of academic resources through the Scottish electronic Staff Development Library

    Directory of Open Access Journals (Sweden)

    Lorna M. Campbell

    2001-12-01

    Full Text Available The Scottish electronic Staff Development Library (http://www.sesdl.scotcit.acuk is an ongoing collaborative project involving the Universities of Edinburgh, Paisley and Strathclyde which has been funded by SHEFC as part of their current ScotCIT Programme (http:llwww.scotcit.ac.uk. This project is being developed in response to the increasing demand for flexible, high-quality staff development materials.

  9. The grinding tip of the sea urchin tooth exhibits exquisite control over calcite crystal orientation and Mg distribution.

    Science.gov (United States)

    Ma, Yurong; Aichmayer, Barbara; Paris, Oskar; Fratzl, Peter; Meibom, Anders; Metzler, Rebecca A; Politi, Yael; Addadi, Lia; Gilbert, P U P A; Weiner, Steve

    2009-04-14

    The sea urchin tooth is a remarkable grinding tool. Even though the tooth is composed almost entirely of calcite, it is used to grind holes into a rocky substrate itself often composed of calcite. Here, we use 3 complementary high-resolution tools to probe aspects of the structure of the grinding tip: X-ray photoelectron emission spectromicroscopy (X-PEEM), X-ray microdiffraction, and NanoSIMS. We confirm that the needles and plates are aligned and show here that even the high Mg polycrystalline matrix constituents are aligned with the other 2 structural elements when imaged at 20-nm resolution. Furthermore, we show that the entire tooth is composed of 2 cooriented polycrystalline blocks that differ in their orientations by only a few degrees. A unique feature of the grinding tip is that the structural elements from each coaligned block interdigitate. This interdigitation may influence the fracture process by creating a corrugated grinding surface. We also show that the overall Mg content of the tooth structural elements increases toward the grinding tip. This probably contributes to the increasing hardness of the tooth from the periphery to the tip. Clearly the formation of the tooth, and the tooth tip in particular, is amazingly well controlled. The improved understanding of these structural features could lead to the design of better mechanical grinding and cutting tools.

  10. Closed-Loop Feedback Flank Errors Correction of Topographic Modification of Helical Gears Based on Form Grinding

    Directory of Open Access Journals (Sweden)

    Huiliang Wang

    2015-01-01

    Full Text Available To increase quality, reduce heavy-duty gear noise, and avoid edge contact in manufacturing helical gears, a closed-loop feedback correction method in topographic modification tooth flank is proposed based on the gear form grinding. Equations of grinding wheel profile and grinding wheel additional radial motion are derived according to tooth segmented profile modification and longitudinal modification. Combined with gear form grinding kinematics principles, the equations of motion for each axis of five-axis computer numerical control forming grinding machine are established. Such topographical modification is achieved in gear form grinding with on-machine measurement. Based on a sensitivity analysis of polynomial coefficients of axis motion and the topographic flank errors by on-machine measuring, the corrections are determined through an optimization process that targets minimization of the tooth flank errors. A numerical example of gear grinding, including on-machine measurement and closed-loop feedback correction completing process, is presented. The validity of this flank correction method is demonstrated for tooth flank errors that are reduced. The approach is useful to precision manufacturing of spiral bevel and hypoid gears, too.

  11. The grinding of uranium dioxide from fluidized beds; Estudio del m icronizado del UO{sub 2} procedente de lechos Fluidizados

    Energy Technology Data Exchange (ETDEWEB)

    Alonso Folgueras, J. A.

    1974-07-01

    This work deals with the UO{sub 2} vibratory grinding, the UO{sub 2} obtained from fluidized beds. In this study the grinding time has been correlated with surface area, stoichiometry, granulometry and grinded product contamination. The efficiency losses in the grinding of moisten UO{sub 2} are outlined. Finally it is made a brief study of the granulate obtained from the grinded UO{sub 2} as well as the green pellets resulting from it, taking into consideration the dispersion of its density and height. (Author)

  12. 重庆高校图书馆电子文献资源建设现状及对策%The Present Situation and Countermeasure of Electronic Literature Resources Construction about Chongqing University Library

    Institute of Scientific and Technical Information of China (English)

    刘子辉; 彭渝; 陈强; 吴晓英

    2014-01-01

    In the information society, Electronic document resources are very important for library development and the school's teaching and research. The university library should pay more at ention to the construction of electronic document resources. Through the survey of the electronic document resources in Chongqing, We have mastered the distribution of electronic document resources, analyzed the existing problems in resource construction, and proposed the related countermeasure. We hope to provide reference for the electronic document resources construction.%在信息社会,电子文献资源对高校图书馆建设、学校的教学与科研都起到非常重要的作用,各高校图书馆应该更加重视电子文献资源的建设。通过对重庆高校图书馆电子文献资源建设情况进行调查,掌握了本地区电子文献资源的分布情况,分析了资源建设中存在的问题,并提出了相关对策,希望为本地区高校图书馆电子文献资源建设提供参考。

  13. Simulation of Flow and Heat Transfer of Mist/Air Impinging Jet on Grinding Work-Piece

    OpenAIRE

    Fan Jiang; Han Wang; Yijun Wang; Jianhua Xiang

    2016-01-01

    The numerical investigation is presented for flow and heat transfer on grinding work-piece with mist/air impinging jet by using DPM (discrete phase model) model. The tracks of the mist droplets show most of them are accumulated on the right surface of grinding zone, and can be influenced by the rotating speed of the grinding wheel, the position and the number of the jet nozzle. The mechanism model of enhance cooling by mist/air impinging jet is developed, which indicated the mist droplet is a...

  14. Effectiveness of dust control methods for crystalline silica and respirable suspended particulate matter exposure during manual concrete surface grinding.

    Science.gov (United States)

    Akbar-Khanzadeh, Farhang; Milz, Sheryl A; Wagner, Cynthia D; Bisesi, Michael S; Ames, April L; Khuder, Sadik; Susi, Pam; Akbar-Khanzadeh, Mahboubeh

    2010-12-01

    Concrete grinding exposes workers to unacceptable levels of crystalline silica dust, known to cause diseases such as silicosis and possibly lung cancer. This study examined the influence of major factors of exposure and effectiveness of existing dust control methods by simulating field concrete grinding in an enclosed workplace laboratory. Air was monitored during 201 concrete grinding sessions while using a variety of grinders, accessories, and existing dust control methods, including general ventilation (GV), local exhaust ventilation (LEV), and wet grinding. Task-specific geometric mean (GM) of respirable crystalline silica dust concentrations (mg/m³ for LEV:HEPA-, LEV:Shop-vac-, wet-, and uncontrolled-grinding, while GV was off/on, were 0.17/0.09, 0.57/0.13, 1.11/0.44, and 23.1/6.80, respectively. Silica dust concentrations (mg/m³ using 100-125 mm (4-5 inch) and 180 mm (7 inch) grinding cups were 0.53/0.22 and 2.43/0.56, respectively. GM concentrations of silica dust were significantly lower for (1) GV on (66.0%) vs. off, and (2) LEV:HEPA- (99.0%), LEV:Shop-vac- (98.1%) or wet- (94.4%) vs. uncontrolled-grinding. Task-specific GM of respirable suspended particulate matter (RSP) concentrations (mg/m³ for LEV:HEPA-, LEV:Shop-vac-, wet-, and uncontrolled grinding, while GV was off/on, were 1.58/0.63, 7.20/1.15, 9.52/4.13, and 152/47.8, respectively. GM concentrations of RSP using 100-125 mm and 180 mm grinding cups were 4.78/1.62 and 22.2/5.06, respectively. GM concentrations of RSP were significantly lower for (1) GV on (70.2%) vs. off, and (2) LEV:HEPA- (98.9%), LEV:Shop-vac- (96.9%) or wet- (92.6%) vs. uncontrolled grinding. Silica dust and RSP were not significantly affected by (1) orientation of grinding surfaces (vertical vs. inclined); (2) water flow rates for wet grinding; (3) length of task-specific sampling time; or, (4) among cup sizes of 100, 115 or 125 mm. No combination of factors or control methods reduced an 8-hr exposure level to below the

  15. Modeling and research of temperature distribution in surface layer of titanium alloy workpiece during AEDG and conventional grinding

    Science.gov (United States)

    Gołąbczak, M.; Gołąbczak, A.; Konstantynowicz, A.; Święcik, R.

    2016-11-01

    Titanium and its alloys are widely recognized as the hardly machinable materials, especially due to their relatively high hardness, low thermal conductivity and possible subcritical superplasticity. Then, a thorough control of the machining process parameters shall be maintained. In this paper, we have concentrated on the grinding of the Ti6Al4V titanium alloy using cBN (boron nitride) grinding wheel combined with the AEDG (abrasive electrodischarge grinding) process. The mathematical model we have dealt with has been based mainly on Jaeger model of the heat taking over between sliding bodies with substantial upgrades related to:estimation of the frictional heat generating based on friction forces distribution,

  16. ELID Mirror Grinding Technology——Development of Metal Bonded Grinding Wheel%ELID镜面磨削技术——金属结合剂砂轮的研制

    Institute of Scientific and Technical Information of China (English)

    关佳亮; 郭东明; 周曙光; 袁哲俊

    2001-01-01

    As the result of the study on the effects of copper powder and other relative metal additives used for ELID grinding wheel manufacturing, a new kind of grinding wheel is presented for ELID grinding and experimental results show that such a grinding wheel has its great advantage and can be used for production pur pose.%采用铜粉、还原铁粉、铸铁粉并辅以改善铁粉和铸铁粉末冶金性能的金属添加剂作配方,烧制出适合现有生产条件的ELID磨削用砂轮磨块。性能检验表明该配方满足了ELID磨削要求。

  17. Selection and Evaluation of Electronic Resources Elektronik Kaynakların Seçimi ve Değerlendirilmesi

    Directory of Open Access Journals (Sweden)

    Doğan Atılgan

    2009-12-01

    Full Text Available Publication boom and issues related to controlling and accession of printed sources have created some problems after World War II. Consequently, publishing industry has encountered the problem of finding possible solution for emerged situation. Industry of electronic publishing has started to improve with the rapid increase of the price of printed sources as well as the problem of publication boom. The first effects of electronic publishing were appeared on the academic and scholarly publications then electronic publishing became a crucial part of all types of publications. As a result of these developments, collection developments and service policies of information centers were also significantly changed. In this article, after a general introduction about selection and evaluation processes of electronic publications, the subscribed databases by a state and a privately owned university in Turkey and their usage were examined. İkinci dünya savaşından sonra görülen yayın patlaması, basılı kaynakların denetim ve erişiminde sorunlar yaşanmasına neden olmuştur. Bu da yayıncılık sektöründe yeni arayışlara yol açmıştır. 1980’li yıllardan sonra basılı yayın fiyatlarındaki hızlı artış da bu etmenlere eklenince elektronik yayıncılık sektörü gelişmeye başlamıştır. Öncelikle bilimsel ve akademik yayınlarla başlayan elektronik yayın günümüzde tüm yayın türlerini kapsamaktadır. Yayıncılıktaki bu gelişim bilgi merkezlerinin derme geliştirme ve hizmet politikalarını da önemli ölçüde değiştirmiştir. Bu çalışmada elektronik yayınların seçim, değerlendirme ve sağlama konularında genel bir girişten sonra bir devlet üniversitesinin bir de özel üniversitenin abone olduğu veritabanları ve bu veri tabanlarının kullanımının değerlendirilmesi yapılmaktadır.

  18. Utility of the electronic information resource UpToDate for clinical decision-making at bedside rounds.

    Science.gov (United States)

    Phua, J; See, K C; Khalizah, H J; Low, S P; Lim, T K

    2012-02-01

    Clinical questions often arise at daily hospital bedside rounds. Yet, little information exists on how the search for answers may be facilitated. The aim of this prospective study was, therefore, to evaluate the overall utility, including the feasibility and usefulness of incorporating searches of UpToDate, a popular online information resource, into rounds. Doctors searched UpToDate for any unresolved clinical questions during rounds for patients in general medicine and respiratory wards, and in the medical intensive care unit of a tertiary teaching hospital. The nature of the questions and the results of the searches were recorded. Searches were deemed feasible if they were completed during the rounds and useful if they provided a satisfactory answer. A total of 157 UpToDate searches were performed during the study period. Questions were raised by all ranks of clinicians from junior doctors to consultants. The searches were feasible and performed immediately during rounds 44% of the time. Each search took a median of three minutes (first quartile: two minutes, third quartile: five minutes). UpToDate provided a useful and satisfactory answer 75% of the time, a partial answer 17% of the time and no answer 9% of the time. It led to a change in investigations, diagnosis or management 37% of the time, confirmed what was originally known or planned 38% of the time and had no effect 25% of the time. Incorporating UpToDate searches into daily bedside rounds was feasible and useful in clinical decision-making.

  19. Condition monitoring on grinding wheel wear using wavelet analysis and decision tree C4.5 algorithm

    Directory of Open Access Journals (Sweden)

    S.Devendiran

    2013-10-01

    Full Text Available A new online grinding wheel wear monitoring approach to detect a worn out wheel, based on acoustic emission (AE signals processed by discrete wavelet transform and statistical feature extraction carried out using statistical features such as root mean square and standard deviation for each wavelet decomposition level and classified using tree based knowledge representation methodology decision tree C4.5 data mining techniques is proposed. The methodology was validate with AE signal data obtained in Aluminium oxide 99 A(38A grinding wheel which is used in three quarters of majority grinding operations under different grinding conditions to validate the proposed classification system. The results of this scheme with respect to classification accuracy were discussed.

  20. Bending Distortion Analysis of a Steel Shaft Manufacturing Chain from Cold Drawing to Grinding

    Science.gov (United States)

    Dias, Vinicius Waechter; da Silva Rocha, Alexandre; Zottis, Juliana; Dong, Juan; Epp, Jérémy; Zoch, Hans Werner

    2017-04-01

    Shafts are usually manufactured from bars that are cold drawn, cut machined, induction hardened, straightened, and finally ground. The main distortion is characterized by bending that appears after induction hardening and is corrected by straightening and/or grinding. In this work, the consequence of the variation of manufacturing parameters on the distortion was analyzed for a complete manufacturing route for production of induction hardened shafts made of Grade 1045 steel. A DoE plan was implemented varying the drawing angle, cutting method, induction hardening layer depth, and grinding penetration depth. The distortion was determined by calculating curvature vectors from dimensional analysis by 3D coordinate measurements. Optical microscopy, microhardness testing, residual stress analysis, and FEM process simulation were used to evaluate and understand effects of the main carriers of distortion potential. The drawing process was identified as the most significant influence on the final distortion of the shafts.

  1. Synthesis and electrochemical preformances of tribasic and tetrabasic lead sulfates prepared by reactive grinding

    Science.gov (United States)

    Grugeon-Dewaele, S.; Laruelle, S.; Joliveau-Vallat, F.; Torcheux, L.; Delahaye-Vidal, A.

    Tribasic lead sulfate (3BS) and tetrabasic lead sulfate (4BS), used as precursors of the positive active material in the lead/acid batteries, were prepared by a new method: reactive grinding. The effects of various experimental parameters (stoichiometry, hygrometry of the starting compounds, duration of mechanical treatment) upon the nature and morphological features of the resulting phase were investigated. Among them, hygrometry turned out to be the most critical one. With water in excess, only 3BS was produced while dry reagents led to 4BS. In both cases, samples with a small particle size and high reactivity were obtained. In order to evaluate the influence of the morphology upon the electrochemical performances of such grinding produced samples, the capacity was measured and compared with that of traditional 3BS and 4BS samples.

  2. An investigation of the corrosive wear of steel balls in grinding of sulphide ores

    Directory of Open Access Journals (Sweden)

    Asghar Azizi

    2015-06-01

    Full Text Available Ball mills are common grinding equipment in mineral processing industries. Ball wear results from three mechanisms namely impact, abrasion and corrosion. Of these, the corrosion mechanism is the least investigated, due to its chemical-electrochemical nature. Therefore, the aims of this research were to investigate the grinding chemistry influence (slurry pH, solid percentage, water chemistry and gas purging on corrosive wear of steel balls and to determine the contribution of corrosion mechanism to total wear of steel balls. The results indicated that the mass losses of steel balls could be reduced considerably by controlling the pulp chemistry inside the mill. In addition, the results showed that 73.51% of the corrosion products are generated from the oxidation of steel balls. It was also estimated that the corrosion mechanism accounts for 26.68% of the total wear of steel balls.

  3. Freeform surface grinding and polishing by CCOS based on industrial robot

    Science.gov (United States)

    Liu, HaiTao; Wan, YongJian; Zeng, ZhiGe; Xu, LiChao; Zhao, HongShen; Fang, Kai

    2016-10-01

    The grinding and polishing of freeform surface by using Computer Controlled Optical Surfacing (CCOS) technology are discussed. Instead of using Computer Numeric Control (CNC) machine, a 6-axises industrial robot TX200 from Stäubli Co. Ltd. is used as the motion platform. In order to perform the movement that CCOS technology needs, the coordinate system of the robot in processing is reviewed and the offline programming method for robot is presented. The material removal experiments during grinding and polishing process on the robotic CCOS platform are been carried out. A rectangular toroid surface workpiece and a circular off-axis parabolic surface workpiece are being fabricated on the robotic CCOS platform, and the latest results will be discussed here.

  4. The effect of bean origin and temperature on grinding roasted coffee

    Science.gov (United States)

    Uman, Erol; Colonna-Dashwood, Maxwell; Colonna-Dashwood, Lesley; Perger, Matthew; Klatt, Christian; Leighton, Stephen; Miller, Brian; Butler, Keith T.; Melot, Brent C.; Speirs, Rory W.; Hendon, Christopher H.

    2016-04-01

    Coffee is prepared by the extraction of a complex array of organic molecules from the roasted bean, which has been ground into fine particulates. The extraction depends on temperature, water chemistry and also the accessible surface area of the coffee. Here we investigate whether variations in the production processes of single origin coffee beans affects the particle size distribution upon grinding. We find that the particle size distribution is independent of the bean origin and processing method. Furthermore, we elucidate the influence of bean temperature on particle size distribution, concluding that grinding cold results in a narrower particle size distribution, and reduced mean particle size. We anticipate these results will influence the production of coffee industrially, as well as contribute to how we store and use coffee daily.

  5. MECHANICAL DISINTEGRATION OF WHEAT STRAW BY ROLLER-PLATE GRIND SYSTEM WITH SHARP-EDGED SEGMENTS

    Directory of Open Access Journals (Sweden)

    Lukas Kratky

    2015-04-01

    Full Text Available Colloid mills and extruders are widely used for disintegrating wet fibrous biomass. However, their main disadvantages are a high energy requirement in the range of hundreds or thousands of kWh per ton of material, and the fact that they grind in process cycles. Efforts have therefore been made to design a new type of continuously operated grinder. Its disintegration principle uses a roller-plate grinding system with sharp-edged segments, where the compressive and shear forces combine to comminute the particles. Test experiments verified that the grinder disintegrates wet untreated straw to particles below 10mm in an effective manner in a single pass, with an energy requirement of 50 kWht−1 TS. A 23% increase in biogas yield was achieved, leading to a net gain in electric energy of310 kWht−1 TS.

  6. High Efficiency Axial Deep Creep-Feed Grinding Machining Technology of Engineering Ceramics Materials

    Institute of Scientific and Technical Information of China (English)

    GUO Fang; ZHANG Baoguo; LU Hong; TIAN Xinli; WANG Jianquan; LI Fuqiang

    2012-01-01

    Axial deep creep-feed grinding machining technology is a high efficiency process method of engineering ceramics materials,which is an original method to process the cylindrical ceramics materials or hole along its axis.The analysis of axial force and edge fracture proved the cutting thickness and feed rate could be more than 5-10 mm and 200 mm/min respectively in once process,and realized high efficiency,low-cost process of engineering ceramics materials.Compared with high speed-deep grinding machining,this method is also a high efficiency machining technology of engineering ceramics materials as well as with low cost.In addition,removal mechanism analyses showed that both median/radial cracks and lateral cracks appeared in the part to be removed,and the processed part is seldom destroyed,only by adjusting the axial force to control the length of transverse cracks.

  7. Application of multi regressive linear model and neural network for wear prediction of grinding mill liners

    Directory of Open Access Journals (Sweden)

    Farzaneh Ahmadzadeh

    2013-06-01

    Full Text Available The liner of an ore grinding mill is a critical component in the grinding process, necessary for both high metal recovery and shell protection. From an economic point of view, it is important to keep mill liners in operation as long as possible, minimising the downtime for maintenance or repair. Therefore, predicting their wear is crucial. This paper tests different methods of predicting wear in the context of remaining height and remaining life of the liners. The key concern is to make decisions on replacement and maintenance without stopping the mill for extra inspection as this leads to financial savings. The paper applies linear multiple regression and artificial neural networks (ANN techniques to determine the most suitable methodology for predicting wear. The advantages of the ANN model over the traditional approach of multiple regression analysis include its high accuracy.

  8. A mathematical model for surface roughness of fluidic channels produced by grinding aided electrochemical discharge machining (G-ECDM)

    OpenAIRE

    Ladeesh V. G.; Manu R

    2017-01-01

    Grinding aided electrochemical discharge machining is a hybrid technique, which combines the grinding action of an abrasive tool and thermal effects of electrochemical discharges to remove material from the workpiece for producing complex contours. The present study focuses on developing fluidic channels on borosilicate glass using G-ECDM and attempts to develop a mathematical model for surface roughness of the machined channel. Preliminary experiments are conducted to study the effect of mac...

  9. Towards improved solubility of poorly water-soluble drugs: cryogenic co-grinding of piroxicam with carrier polymers.

    Science.gov (United States)

    Penkina, Anna; Semjonov, Kristian; Hakola, Maija; Vuorinen, Sirpa; Repo, Timo; Yliruusi, Jouko; Aruväli, Jaan; Kogermann, Karin; Veski, Peep; Heinämäki, Jyrki

    2016-01-01

    Amorphous solid dispersions (SDs) open up exciting opportunities in formulating poorly water-soluble active pharmaceutical ingredients (APIs). In the present study, novel catalytic pretreated softwood cellulose (CPSC) and polyvinylpyrrolidone (PVP) were investigated as carrier polymers for preparing and stabilizing cryogenic co-ground SDs of poorly water-soluble piroxicam (PRX). CPSC was isolated from pine wood (Pinus sylvestris). Raman and Fourier transform infrared (FTIR) spectroscopy, X-ray powder diffraction (XRPD) and differential scanning calorimetry (DSC) were used for characterizing the solid-state changes and drug-polymer interactions. High-resolution scanning electron microscope (SEM) was used to analyze the particle size and surface morphology of starting materials and final cryogenic co-ground SDs. In addition, the molecular aspects of drug-polymer interactions and stabilization mechanisms are presented. The results showed that the carrier polymer influenced both the degree of amorphization of PRX and stabilization against crystallization. The cryogenic co-ground SDs prepared from PVP showed an enhanced dissolution rate of PRX, while the corresponding SDs prepared from CPSC exhibited a clear sustained release behavior. In conclusion, cryogenic co-grinding provides a versatile method for preparing amorphous SDs of poorly water-soluble APIs. The solid-state stability and dissolution behavior of such co-ground SDs are to a great extent dependent on the carrier polymer used.

  10. The Tucker technique: the proximal hollow grind to address a root concavity.

    Science.gov (United States)

    Hess, T A

    2014-01-01

    Cast gold inlays have long been used to conservatively restore compromised tooth structure. When the mesial or distal proximal surfaces are indicated for restoration and a cast gold restoration is desired, traditionally a box is prepared with an external bevel. Often a root concavity does not allow for a standard box form or the external and/or internal bevels. A proximal hollow grind can be utilized to address limits of standard inlay or onlay preparation design.

  11. Analysis of surface integrity of grinded gears using Barkhausen noise analysis and x-ray diffraction

    Energy Technology Data Exchange (ETDEWEB)

    Vrkoslavová, Lucie; Louda, Petr [Institute for Nanomaterials, Advanced Technologies and Innovation, Technical University of Liberec (Czech Republic); Malec, Jiři [Department of Analytic Services, PCS s.r.o. (Czech Republic)

    2014-02-18

    The contribution is focused to present results of study grinded gears made of 18CrNiMo7-6 steel used in the wind power plant for support (service) purposes. These gears were case-hardened due to standard hard case and soft core formation. This heat treatment increases wear resistance and fatigue strength of machine parts. During serial production some troubles with surface integrity have occurred. When solving complex problems lots of samples were prepared. For grinding of gears were used different parameters of cutting speed, number of material removal and lots from different subsuppliers. Material characterization was carried out using Barkhausen noise analysis (BNA) device; X-ray diffraction (XRD) measurement of surface residual stresses was done as well. Depth profile of measured characteristics, e.g. magnetoelastic parameter and residual stress was obtained by step by step layers' removing using electrolytic etching. BNA software Viewscan was used to measure magnetizing frequency sweep (MFS) and magnetizing voltage sweep (MVS). Scanning of Magnetoelastic parameter (MP) endwise individual teeth were also carried out with Viewscan. These measurements were done to find problematic surface areas after grinding such as thermal damaged locations. Plots of the hardness and thickness of case-hardened layer on cross sections were measurered as well. Evaluation of structure of subsurface case-hardened layer and core was made on etched metallographic patterns. The aim of performed measurements was to find correlation between conditions of grinding, residual stresses and structural and magnetoelastic parameters. Based on correlation of measured values and technological parameters optimizing the production of gears will be done.

  12. 移动磨削装置的设计%The Design of Mobile Grinding Device

    Institute of Scientific and Technical Information of China (English)

    张占福; 赵志

    2014-01-01

    移动磨削装置的设计,主要是利用普通机床设备,通过增加自行设计开发的移动式卧车磨削装置,将其装夹在卧式车床的刀架上,作为磨削工具,使其达到以车代磨的目的,实现对矿浆输送隔膜泵设备中各种不同规格隔膜室的远距离、高磨蚀加工。该移动式卧车磨削隔膜室装置具有效率高、运行可靠和制造成本低等诸多优点,有利于节约能源和环境保护,市场前景非常广阔,现广泛应用于公司各种国内大型隔膜腔及内孔圆弧加工。%The design of moving grinding equipment is made by adding moving lie -grinding device to the-machine tool facility .The device is loaded on knife rest of lie -grindiing . As a grinding tool ,this gringding equipment can machine the septum -ventricle of the mine -feeding septum -equipment in long distance and hight ablation .This make turning machining displace grinding machining .The equipment has some merit as hight -efficiency ,good credibility and lower cost . In favor of saving energy and protecting envi-ronment ,this equipment has very great foreground in market and had been used in machining the septum -ventricle and the arc of in hole at our company .

  13. Analysis of surface integrity of grinded gears using Barkhausen noise analysis and x-ray diffraction

    Science.gov (United States)

    Vrkoslavová, Lucie; Louda, Petr; Malec, Jiři

    2014-02-01

    The contribution is focused to present results of study grinded gears made of 18CrNiMo7-6 steel used in the wind power plant for support (service) purposes. These gears were case-hardened due to standard hard case and soft core formation. This heat treatment increases wear resistance and fatigue strength of machine parts. During serial production some troubles with surface integrity have occurred. When solving complex problems lots of samples were prepared. For grinding of gears were used different parameters of cutting speed, number of material removal and lots from different subsuppliers. Material characterization was carried out using Barkhausen noise analysis (BNA) device; X-ray diffraction (XRD) measurement of surface residual stresses was done as well. Depth profile of measured characteristics, e.g. magnetoelastic parameter and residual stress was obtained by step by step layers' removing using electrolytic etching. BNA software Viewscan was used to measure magnetizing frequency sweep (MFS) and magnetizing voltage sweep (MVS). Scanning of Magnetoelastic parameter (MP) endwise individual teeth were also carried out with Viewscan. These measurements were done to find problematic surface areas after grinding such as thermal damaged locations. Plots of the hardness and thickness of case-hardened layer on cross sections were measurered as well. Evaluation of structure of subsurface case-hardened layer and core was made on etched metallographic patterns. The aim of performed measurements was to find correlation between conditions of grinding, residual stresses and structural and magnetoelastic parameters. Based on correlation of measured values and technological parameters optimizing the production of gears will be done.

  14. DESIGN OF INTELLIGENT CONTROL SYSTEM USING ACOUSTIC PARAMETERS FOR GRINDING MILL OPERATION

    Directory of Open Access Journals (Sweden)

    Sonali Sen

    2013-02-01

    Full Text Available This paper utilizes acoustic parameters such as FS,NC, N, P, INC, FL, FH, W for acoustic signals S of different running conditions of a ballmill to deriveout the acoustic signatures and hence control signals, which is to be used for designing the control systems of the mill. The parameters FS, NC, N, P, INC, FL, FH and W are represented by sample rate in Hz, number of cepstral coefficients, length of frame in samples, number of filters in filter bank, frame increment, low end of the lowest filter, high end of highest filter and the window over which the analysis is to be performed respectively. The work establishes an appropriate theoretical background that helps to predict dynamic breakage characteristics with respect to particle size distribution of materials, adequately supported by experimental data. The signatures of different running conditions of grinding mill have been extracted from the captured signal in time frame these have been used as feedback signal to monitor the grinding operation. Condenser based microphones have been used for capturing acoustic signals in time domain directly in computers and stored for further analysis. Matlab R2010b has been used for different analysis of the experiment. On analyzing the signatures, it has been observed whether the fines are produced progressively to attain the desired size range or the mill producing undesired products. Thus, the approach has been used in this paper has the ability to arrive in the stage of optimum grinding by tuning parameters of the mill in real time, and also it can prevent the mill to enter into an erroneous state. Moreover, on study it has found that the present scheme can be used more accurately in comparison to the earlier work of the author. This paper presents an implementation scheme to use acoustic signal as the control signal to regulate the operation of a grinding mill.

  15. Performance of an electrochemical COD (chemical oxygen demand) sensor with an electrode-surface grinding unit.

    Science.gov (United States)

    Geun Jeong, Bong; Min Yoon, Seok; Ho Choi, Chang; Koang Kwon, Kil; Sik Hyun, Moon; Heui Yi, Dong; Soo Park, Hyung; Kim, Mia; Joo Kim, Hyung

    2007-12-01

    An electrochemical COD (chemical oxygen demand) sensor using an electrode-surface grinding unit was investigated. The electrolyzing (oxidizing) action of copper on an organic species was used as the basis of the COD measuring sensor. Using a simple three-electrode cell and a surface grinding unit, the organic species is activated by the catalytic action of copper and oxidized at a working electrode, poised at a positive potential. When synthetic wastewater was fed into the system, the measured Coulombic yields were found to be dependent on the COD of the synthetic wastewater. A linear correlation between the Coulombic yields and the COD of the synthetic wastewater was established (10-1000 mg L(-1)) when the electrode-surface grinding procedure was activated briefly at 8 h intervals. When various kinds of wastewater samples obtained from various sewage treatment plants were measured, linear correlations (r(2)> or = 0.92) between the measured EOD (electrochemical oxygen demand) value and COD of the samples were observed. At a practical wastewater treatment plant, the measurement system was successfully operated with high accuracy and good stability over 3 months. These experimental results show that the application of the measurement system would be a rapid and practical method for the determination of COD in water industries.

  16. Experimental Study of Machinability in Mill-grinding of SiCp/Al Composites

    Institute of Scientific and Technical Information of China (English)

    LI Jianguang; DU Jinguang; YAO Yingxue; HAO Zhaopeng; LIU Xiao

    2014-01-01

    An attempt was made to investigate the machinability of SiCp/Al composites based on the experimental study using mill-grinding processing method. The experiments were carried out on a high-speed CNC machining center using integrated abrasive cutting tool. The effects of combined machining parameters, e g, cutting speed (vs), feed rate (vf), and depth of cut (ap), with the same change of material removal rate (MRR) on the mill-grinding force and surface roughness (Ra) were investigated. The formation mechanism of typical machined surface defects was analyzed by SEM. The experimental results reveal that with the same change of material removal rate, lower mill-grinding force values can be gained by increasing depth of cut and feed rate simultaneously at higher cutting speed. With the same change of MRR value, lower surface roughness values can be gained by increasing the feed rate at higher cutting speed, rather than just increasing the depth of cut, or increasing the feed rate and depth of cut simultaneously. The machined surface of SiCp/Al composites reveals typical defects which can influence surface integrity.

  17. DETERMINATION AND OPTIMIZATION OF CYLINDRICAL GRINDING PROCESS PARAMETERS USING TAGUCHI METHOD AND REGRESSION ANALYSIS

    Directory of Open Access Journals (Sweden)

    M.Janardhan

    2011-07-01

    Full Text Available Cylindrical grinding is one of the important metal cutting processes used extensively in the finishing operations. Metal removal rate and surface finish are the important out put responses in the production with respect to quantity and quality respectively. The Experiments are conducted on CNC cylindrical grinding machine with L9 Orthogonal array with input machining variables as work speed, feed rate and depth of cut. Empirical models are developed using design of experiments and response surface methodology. The adequacy of thedeveloped model is tested with ANNOVA. The developed model can be used by the different manufacturing firms to select right combination of machining parameters to achieve an optimal metal removal rate (MRR and surface roughness (Ra.The results reveals that feed rate, depth of cut are influences predominantly on the output responses metal removal rate (MRR and surface roughness (Ra.The predicted optimal values for MRR, Ra for Cylindrical grinding process are 62.05 gm/min and 0.816 μm respectively. The results are further confirmed by conducting confirmation experiments.

  18. Rapidly removing grinding damage layer on fused silica by inductively coupled plasma processing

    Science.gov (United States)

    Chen, Heng; Zhou, Lin; Xie, Xuhui; Shi, Baolu; Xiong, Haobin

    2016-10-01

    During the conventional optical shaping process of fused silica, lapping is generally used to remove grinding damage layer. But this process is of low efficiency, it cannot meet the demand of large aperture optical components. Therefore, Inductively Coupled Plasma Processing (ICPP) was proposed to remove grinding damage layer instead of lapping. ICPP is a non-contact, deterministic figuring technology performed at atmospheric pressure. The process benefits from its ability to simultaneously remove sub-surface damage (SSD) while imparting the desired figure to the surface with high material remove rate. The removing damage capability of ICPP has preliminarily been confirmed on medium size optical surfaces made of fused silica, meanwhile serious edge warping was found. This paper focused on edge effect and a technique has been designed to compensate for these difficulties. Then it was demonstrated on a large aperture fused silica mirror (Long320mm×Wide370mm×High50mm), the removal depth was 30.2μm and removal rate got 6.6mm3/min. The results indicate that ICPP can rapidly remove damage layer on the fused silica induced by the previous grinding process and edge effect is effective controlled.

  19. Wheel efficiency in the diamond-spark erosion grinding of tungsten carbides

    Science.gov (United States)

    Uzunjan, M. D.; Krasnoscek, J. S.

    1982-11-01

    Diamond-spark erosion grinding on metallic bond is a highly productive process used in working difficult materials. It is of considerable interest to investigate the efficiency of diamond wheels in the grinding of hard alloys while supplying impulse energy to the cutting zone. The efficiency of 150 x 10 x 3 ACK cup wheels made with ACB diamonds on MB1 bond as evaluated experimentally by the multifactor method using the following optimized parameters: removal rate Q (cu mm/min), specific diamond consumption q (mg/g) and a specific grinding cost C (kopecks/cu cm). A TI5K6 hard alloy sample 60 sq mm in cross section was ground using a 3B642 grinder with a 3% soda solution as coolant. The cutting zone was supplied with electrical impulse energy from an SGI 40-440 generator. The mean current ranged from 4 to 10 amps, the impulse frequency was 88 kHz, the degree of porosity was 2, the anode was the diamond wheel and the cathode was the treated material.

  20. Systematic Geometric Error Modeling for Workspace Volumetric Calibration of a 5-axis Turbine Blade Grinding Machine

    Institute of Scientific and Technical Information of China (English)

    Abdul Wahid Khan; Chen Wuyi

    2010-01-01

    A systematic geometric model has been presented for calibration of a newly designed 5-axis turbine blade grinding machine.This machine is designed to serve a specific purpose to attain high accuracy and high efficiency grinding of turbine blades by eliminating the hand grinding process.Although its topology is RPPPR (P:prismatic;R:rotary),its design is quite distinct from the competitive machine tools.As error quantification is the only way to investigate,maintain and improve its accuracy,calibration is recommended for its performance assessment and acceptance testing.Systematic geometric error modeling technique is implemented and 52 position dependent and position independent errors are identified while considering the machine as five rigid bodies by eliminating the set-up errors ofworkpiece and cutting tool.39 of them are found to have influential errors and are accommodated for finding the resultant effect between the cutting tool and the workpiece in workspace volume.Rigid body kinematics techniques and homogenous transformation matrices are used for error synthesis.

  1. Mathematical models of grinding manufacture and tooth contact analysis of spherical gears

    Institute of Scientific and Technical Information of China (English)

    2009-01-01

    The spherical gear is a gear-driven mechanism with two degrees of freedom (DOF), which can transfer spatial motion and power. Grinding machining of the spherical gear is performed with a plate grinding wheel by using generating method, and based on mathematical model of the plate grinding wheel, the mathematical model of the spherical gear is set up. And then, the meshing model of a spherical gear pair is developed and the tooth contact analysis (TCA) of the spherical gear pairs is performed. After that, the position of a contact point on teeth surfaces of the spherical gear pair can be solved by using a nonlinear solver. Finally, the paths of contact points on teeth surfaces of the spherical gear are studied: Since every tooth of the spherical gear is diverse, the contact paths of the meshing of the spherical gear pair are complex and multiform. These are very useful to further investigations on transmission theory and practical applications of spherical gear pairs.

  2. Influence of suspension stability on wet grinding for production of mineral nanoparticles

    Institute of Scientific and Technical Information of China (English)

    S. Sakthivel; Venkatesan V. Krishnan; Pitchumani

    2008-01-01

    Grinding behavior of nanoparticles in an attritor mill and the minimum achievable particle size are strongly influenced by the suspension stability. In the present work, suspension stability (i.e. (-potential) of nanoparticles was studied by measuring pH as a function of grinding time in the wet milling process. It was found that after a certain time in an attritor mill, there is no further size reduction and the average product particle size increases monotonically. One of the reasons is that the production of submicron particles leads to more particle-particle interactions and consequently pH of the suspension decreases with grinding time. Usually pH value is related to suspension stability and it can be enhanced by addition of NaOH solution. The maximum negative (-potential of -51.2 mV was obtained at pH of 12 for silica. The higher the (-potential with the same polarity, higher will be the electrostatic repulsion between the particles. Hence, the maximum electrostatic repulsion force was maintained by the adjustment of pH value in wet milling. The experiments were conducted at different pH conditions which were maintained constant throughout the experiments and nanosized particles were obtained consequently.

  3. Application of Ultra-Small Micro Grinding and Micro Milling Tools: Possibilities and Limitations

    Directory of Open Access Journals (Sweden)

    Benjamin Kirsch

    2017-08-01

    Full Text Available Current demands for flexible, individual microstructures in high quality result in high requirements for micro tools. As the tool size defines the minimum structure size, ultra-small tools are needed. To achieve tool diameters of 50 µm and lower, we investigate the complete manufacturing chain of micro machining. From the development of the machine tools and components needed to produce and apply the micro tools, the micro tools themselves, as well as the micro machining processes. Machine tools are developed with the possibility of producing the micro geometry (cutting edge design of micro tools as well as plating processes to produce super abrasive micro grinding tools. Applying these setups, we are able to produce ultra-small micro grinding and micro milling tools with typical diameters of 50 µm and down to 4 µm. However, the application of such tools is very challenging. The article presents possibilities and limitations in manufacturing the micro tools themselves as well as microstructures made with these tools. A special emphasis will be on the influence of the tool substrate in micro milling and grain sizes in micro grinding.

  4. Study of pulmonary (lung) functioning of commercial wheat grinding machine operators in India using spirometric testing.

    Science.gov (United States)

    Agashe, Abhijeet; Deshpande, V S

    2010-04-01

    In ancient times, in India each household had a chakki to mill the wheat. There was no concept of getting wheat grounded from outside. With the fast changing lifestyle, this tradition has almost disappeared now. Today every city of India has numerous commercial wheat grinding machine shops located at various places. Other than states like Punjab, this occupation is mostly unorganized and little has been done to look into the welfare and health of these machine operators. Like most of the occupations, this occupation of wheat grinding also has several occupational hazards and injuries associated with it. The most obvious of them all in this case is due to the continuous exposure of the operators to the rising dust wheat particles, commonly called atta). This perpetual inhaling ofpollutants exposes the operators to risks of pulmonary malfunctioning. Therefore, this paper attempts to determine the pulmonary functioning of the commercial wheat grinding machine operators in India using spirometric testing. On the basis of the anthropometric data, effort has been done to develop the expected lung performance. Further, the actual lung performance of the operators is measured and compared with expected performance.

  5. A Hybrid Multiobjective Differential Evolution Algorithm and Its Application to the Optimization of Grinding and Classification

    Directory of Open Access Journals (Sweden)

    Yalin Wang

    2013-01-01

    Full Text Available The grinding-classification is the prerequisite process for full recovery of the nonrenewable minerals with both production quality and quantity objectives concerned. Its natural formulation is a constrained multiobjective optimization problem of complex expression since the process is composed of one grinding machine and two classification machines. In this paper, a hybrid differential evolution (DE algorithm with multi-population is proposed. Some infeasible solutions with better performance are allowed to be saved, and they participate randomly in the evolution. In order to exploit the meaningful infeasible solutions, a functionally partitioned multi-population mechanism is designed to find an optimal solution from all possible directions. Meanwhile, a simplex method for local search is inserted into the evolution process to enhance the searching strategy in the optimization process. Simulation results from the test of some benchmark problems indicate that the proposed algorithm tends to converge quickly and effectively to the Pareto frontier with better distribution. Finally, the proposed algorithm is applied to solve a multiobjective optimization model of a grinding and classification process. Based on the technique for order performance by similarity to ideal solution (TOPSIS, the satisfactory solution is obtained by using a decision-making method for multiple attributes.

  6. Behavior of surface integrity in cylindrical plunge grinding using different cooling systems

    Directory of Open Access Journals (Sweden)

    Leonardo Roberto Silva

    2011-01-01

    Full Text Available The superficial texture of the material can exert a decisive influence on the application and performance of the machined component. The conventional fluids used in grinding processes are environmental risk and can also be dangerous to the health. The disposal of these toxic fluids is expensive and the contamination in the proximities of the machines can present risks to the health for the personnel in the shop floor. This paper analyzes the performance of the minimum quantity lubricant (MQL technique and compares it with the conventional cooling method, developing an optimized fluid application method using a specially designed nozzle, through which a minimum amount of oil is sprayed in a compressed air flow. This paper also explores and discusses the concept of the MQL in the grinding process of hardened AISI 4340 steel. The performance of the MQL technique in grinding was evaluated based on an analysis of the surface integrity (roughness, microstructure and microhardness. As a result, it was realized that the MQL technique provides very similar characteristics to conventional process and can be applied in industry, thus contributing to an environment friendly manufacturing.

  7. Electrolytic In-process Dressing (ELID) for high-efficiency, precision grinding of ceramic parts: An experiment study

    Energy Technology Data Exchange (ETDEWEB)

    Bandyopadhyay, B.P.

    1995-08-01

    This report describes Electrolytic In-process Dressing (ELID) as applied to the efficient, high-precision grinding of structural ceramics, and describes work performed jointly by Dr. B.P. Bandyopadhyay, University of North Dakota, and Dr. R. Ohmori, of the Institute of Physical and Chemical Research (RINEN), Tokyo, Japan, from June through August, 1994. Dr. Ohmori pioneered the novel ELID grinding technology which incorporates electrolytically enhanced, in-process dressing of metal bonded superabrasive wheels. The principle of ELID grinding technology is discussed in the report as will its application for rough grinding and precision grinding. Two types of silicon nitride based ceramics (Kyocerals Si{sub 3}N{sub 4}, and Eaton`s SRBSN) were ground under various conditions with ELID methods. Mirror surface finishes were obtained with {number_sign} 4000 mesh size wheel (average grain size = 4 {mu}m). Results of these investigations are presented in this report. These include the effects of wheel bond type, type of power supply, abrasive grit friability, and cooling fluid composition. The effects of various parameters are discussed in terms of the mechanisms of ELID grinding, and in particular, the manner of boundary layer formation on the wheels and abrasive grit protrusion.

  8. 热管砂轮干磨削温度场数值模拟%Numerical simulation study on temperature field in dry grinding with heat pipe grinding wheel

    Institute of Scientific and Technical Information of China (English)

    梁星慧; 傅玉灿; 赫青山; 陈琛

    2012-01-01

    基于一种利用热管技术对磨削弧区进行强化换热的构想,采用FLUENT软件建立了环形热管砂轮干磨削温度场的仿真模型,得到了热管换热能力与热流密度、转速和砂轮壁厚的关系,并在相同热流密度下对比了热管砂轮与热管砂轮弧区的温度.仿真结果表明:弧区温度会随着热流密度的增大相应升高,随着转速的增大而降低,热管的启动时间会随着砂轮壁厚的增大减慢;相同热流密度下,热管砂轮的弧区温度明显低于无热管砂轮.最后通过干磨削钛合金TC4试验,对仿真结果进行了验证.%Based on the heat pipe technology to exchange heat, the heat transfer model of heat pipe grinding wheel (HPGW) using Fluent software was established. The influence of heat flux, thickness and rotation speed on the heat exchange capability in grinding zone with HPGW was analyzed in dry grinding process. The grinding temperature of HPGW was also compared with the grinding wheel without heat pipe in the same heat flux. The results showed that the grinding temperature of HPGW went up with the rising heat flux, decreased with the rising rotation speed, and the start lime of heat pipe got longer when the thickness increased. Furthermore, the grinding temperature of HPGW was much lower than the grinding wheel without heat pipe. In the end, the HPGW and the grinding wheel without heat pipe were respectively used lo conduct dry grinding. The experiment results proved the simulation results.

  9. Investigation of Creep Feed Grinding Parameters and Heat treatment Effects on the Nickel-base Superalloys

    Institute of Scientific and Technical Information of China (English)

    Hasan Jamshidi; Sayed Ali Sadough Vanini; Alireza Attari

    2004-01-01

    The Nickel base Superalloys are the most famous complicated and useable of Superalloys to make hot zone components of the gas turbines. The complicated dimensional tolerances, specially at the root of the blade show importance of grinding processes at the production of blades root. The prediction of the effect of machining parameters on the soundness of component surface strengthening for reaching to a suitable surface finishing and avoiding from crack formation at the work part during machining operation often is not easy and feasible so needs to more industrial investigation.This research is about frame 5 blade designed by GE and made from Superalloy IN738LC has been investigated. The formation of a plastically deformed and heat affected zone during grinding of Superalloy IN738LC with a high depth of cut but slow work speed (creep feed grinding) was investigated. Parameters such as work speed, depth of cut and radial dressing speed have been considered as variables and their effects have been studied. During experimental performed, the voltage and current of motor measured and power and special energy calculated.Some samples heat-treated (of the 1176℃ for 1 hr under neutral argon gas and cooling rate of 15℃/min up to 537℃ and then air cooling) to study grains recrystallization. Other samples have been created from the roots of blades and then coated by Nickel to measure boundary layer micro-hardness. The results show that increasing work speed leads to increasing the use power. Increasing the depth of cut, by increasing material removal rate, and the radial dressing speed, by decreasing power, lead to decreasing special energy. The temperature created by grinding lead to decreasing plastic deformation and boundary layer formation. When the radial dressing speed changes from 1 to 0.6 μm/rev and other parameters are kept unchanged the roughness of surface increases and the special energy decreases. Sufficient dressing is very essential in limiting the width

  10. 图书馆纸质资源与电子资源投入比例研究%The research of ratio between traditional and electronics resources in library

    Institute of Scientific and Technical Information of China (English)

    王以婧; 李明

    2012-01-01

    With the popularization of electronic product development,library is no longer the paper-based resources into a single information carrier the pattern,but has formed a paper resource and electronic resources coexist in the new situation.Because the library types of our country,the proportion of input between paper-based resources and other kinds of resources exist difference.This paper will discuss the relationship between the traditional and electronics resources,and also points out the existing problems and the countermeasures.%随着电子产品的普及发展,图书馆已不再以纸质资源为唯一的信息载体,而是形成了纸质资源和电子资源并存的新局面。由于国内图书馆类型的不同,纸质资源与电子资源的配比也会存在差异。通过讨论二者的关系,指出存在的问题及应对之策。

  11. The development of electrolyte grinding fluid on grinding with electrolyte in-process dressing%在线电解修整磨削的电解磨削液研制

    Institute of Scientific and Technical Information of China (English)

    朴承镐; 乔宏; 李杰; 李建军

    2001-01-01

    为了对金属结合剂砂轮电解修整,研究并配制了电解磨削液。根据电解磨削液的性能要求, 分析确定了电解磨削液中具有电解、钝化、防锈和润滑等性能的各组元,并通过静态实验确认了各组元对电解磨削液性能的影响。确定最佳电解磨削液在实际系统中对金属结合剂砂轮进行电解修整得到了较为满意的修整结果。所研制的电解磨削液具有实用价值,可用于生产。%In order to electrolyze dressing grinding wheel of metal binding agent, the elec trolytic grinding fluid is developed. According to the requirements of the elec trolytic grinding fluid, each constituent with properties such as the el ectrolysis, the inactivation, the rust prevention and the lubrication are analyz ed and determined and their effects to the electrolytic grinding fluid is obtain ed through the static experiments. In the actual system, the grinding wheel of metal binding agent is electrolytically dressed with the determined optimum elec trolytic grinding fluid and the satisfied dressing result is obtained. So the d eveloped electrolytic grinding fluid possesses the practical value which can be used in the manufacturing.

  12. There is a Relationship between Resource Expenditures and Reference Transactions in Academic Libraries. A Review of: Dubnjakovic, A. (2012. Electronic resource expenditure and the decline in reference transaction statistics in academic libraries. Journal of Academic Librarianship, 38(2, 94-100. doi:10.1016/j.acalib.2012.01.001

    Directory of Open Access Journals (Sweden)

    Annie M. Hughes

    2013-03-01

    Full Text Available Objective – To provide an analysis of the impact of expenditures on electronic resourcesand gate counts on the increase or decrease in reference transactions.Design – Analysis of results of existing survey data from the National Center for Educational Statistics (NCES 2006 Academic Library Survey(ALS.Setting – Academic libraries in the United States.Subjects – 3925 academic library respondents.Methods – The author chose to use survey data collected from the 2006 ALS conducted bythe NCES. The survey included data on various topics related to academic libraries, but in the case of this study, the author chose to analyze three of the 193 variables included. The three variables: electronic books expenditure, computer hardware and software, and expenditures on bibliographic utilities, were combined into one variable called electronic resource expenditure. Gate counts were also considered as a variable. Electronic resource expenditure was also split as a variable into three groups: low, medium, and high. Multiple regression analysis and general linear modeling, along with tests of reliability, were employed. Main Results – The author determined that low, medium, and high spenders with regard to electronic resources exhibited differences in gate counts, and gate counts have an effect on reference transactions in any given week. Gate counts tend to not have much of an effect on reference transactions for the higher spenders, and higher spenders tend to have a higher number of reference transactions overall. Low spenders have lower gate counts and also a lower amount of reference transactions.Conclusion – The findings from this study show that academic libraries spending more on electronic resources also tend to have an increase with regard to reference transactions. The author also concludes that library spaces are no longer the determining factor with regard to number of reference transactions. Spending more on electronic resources is

  13. SiCp/Al复合材料磨削力实验分析%Experiment analysis on grinding force of SiCp/Al

    Institute of Scientific and Technical Information of China (English)

    石莉; 周丽; 许立福; 黄树涛

    2011-01-01

    SiCp/Al composite material was grinded with diamond wheel on high - precision machine. Acquiring grinding force signals of the experiment with high speed advantech PCI-1712 board. Acquired grinding force signals are analyzed in MATLAB which has mighty function disposing signals. Through analyzing the grinding force in time field and the signals wavelet analysis for different grinding parameters, found that the feed velocity has much more influence on the grinding force, the grinding force ratio and the standard deviation of the grinding force than the depth of grinding when the velocity of the diamond wheel is fixed. The result of the experiment indicates that the grinding force increases and the grinding force ratio decreases with the increasing of feed velocity and grinding depth.%在高精密平面磨床上,使用金刚石砂轮磨削SiCp/Al复合材料,通过PCI-1712高速数据采集卡采集实验数据.在Matlab软件里,通过对不同磨削参数下的信号进行时域和小波分析,得出在砂轮速度一定时,进给速度对磨削力和磨削力比的影响最大,磨削深度次之,实验结果表明:随着进给速度和磨削深度的增大、磨削力增大,磨削力比减小.

  14. 内锥面刃磨机实现麻花钻螺旋面刃磨的研究与仿真%Research and simulation to realize helicoid grinding of twist drill with inner cone grinding machine

    Institute of Scientific and Technical Information of China (English)

    戴俊平; 郭辉; 关文魁; 卜睿

    2012-01-01

    According to the working principle of inner cone grinding machine, the differential of plate units is increased to replace the traditional variable lead.And two step motors are applied to drive respectively ball screw spindle and nut relative rotation and synthetize any thread pitch.Thus the method to achieve adjustable lead helicoid grinding is put forward as well as the method for grinding the helicoid within inner cone grinding machine,and then the formula of relief angle and oblique of chisel edge after grinding is derived.The author designs a virtual prototype of inner cone grinding machine with the Pro/E Software to realize helicoid grinding by motion simulation in its mechanism,which results verify that the mechanism after improving can realize the helicoid grinding.The mechanism is conducive to the realization of digital control of mechanical grinding.%根据内锥面刃磨机的工作原理,增加双层拖板的差动来代替传统的变导程,利用两步进电机分别带动丝杠主轴与螺母相对转动,合成任意螺距.实现导程可调的新螺旋面刃磨的方法,由此实现了在内锥面刃磨机中进行螺旋面刃磨的方法,并推导了刃磨后后角与横刃斜角的公式.然后基于Pro/E软件设计了机构的虚拟样机,并以双层拖板的分析为例对机构实现螺旋面刃磨而进行运动仿真,结果验证了改进后的机构可以实现螺旋面刃磨.此机构有利于实现数字化控制的机械刃磨.

  15. If Information Wants To Be Free...Then Who's Going To Pay for It? [and] A Question of Access: SPARC, BioOne, and Society-Driven Electronic Publishing [and] Who Is Going To Mine Digital Library Resources? And How?

    Science.gov (United States)

    Kaser, Richard T.; Johnson, Richard K.; Rudner, Lawrence

    2000-01-01

    Discusses Fair Use and the public perception; models for funding information services; publishers illusion that information is/should be free; Internet's role in making information freely available; scholarly communication systems: Scholarly Publishing and Academic Resources Coalition (SPARC) and BioOne (an electronic aggregation of bioscience…

  16. If Information Wants To Be Free...Then Who's Going To Pay for It? [and] A Question of Access: SPARC, BioOne, and Society-Driven Electronic Publishing [and] Who Is Going To Mine Digital Library Resources? And How?

    Science.gov (United States)

    Kaser, Richard T.; Johnson, Richard K.; Rudner, Lawrence

    2000-01-01

    Discusses Fair Use and the public perception; models for funding information services; publishers illusion that information is/should be free; Internet's role in making information freely available; scholarly communication systems: Scholarly Publishing and Academic Resources Coalition (SPARC) and BioOne (an electronic aggregation of bioscience…

  17. Impact of two interventions on timeliness and data quality of an electronic disease surveillance system in a resource limited setting (Peru: a prospective evaluation

    Directory of Open Access Journals (Sweden)

    Quispe Jose A

    2009-03-01

    Full Text Available Abstract Background A timely detection of outbreaks through surveillance is needed in order to prevent future pandemics. However, current surveillance systems may not be prepared to accomplish this goal, especially in resource limited settings. As data quality and timeliness are attributes that improve outbreak detection capacity, we assessed the effect of two interventions on such attributes in Alerta, an electronic disease surveillance system in the Peruvian Navy. Methods 40 Alerta reporting units (18 clinics and 22 ships were included in a 12-week prospective evaluation project. After a short refresher course on the notification process, units were randomly assigned to either a phone, visit or control group. Phone group sites were called three hours before the biweekly reporting deadline if they had not sent their report. Visit group sites received supervision visits on weeks 4 & 8, but no phone calls. The control group sites were not contacted by phone or visited. Timeliness and data quality were assessed by calculating the percentage of reports sent on time and percentage of errors per total number of reports, respectively. Results Timeliness improved in the phone group from 64.6% to 84% in clinics (+19.4 [95% CI, +10.3 to +28.6]; p Conclusion Regular phone reminders significantly improved timeliness of reports in clinics and ships, whereas supervision visits led to improved data quality only among clinics. Further investigations are needed to establish the cost-effectiveness and optimal use of each of these strategies.

  18. Metadata for Electronic Information Resources

    Science.gov (United States)

    2004-12-01

    among digital libraries . METS provides an XML DTD that can point to metadata in other schemes by declaring the scheme that is being used. For example...site: www.niso.org/news/Metadata_simpler.pdf International Federation of Library Associations and Institutions (IFLA). (2002). Digital Libraries : Metadata

  19. 基于ASP.NET的电子资源整合系统设计与实现%Design and Realization of an Integrated Electronic Resource System Based on ASP.NET

    Institute of Scientific and Technical Information of China (English)

    冀宪武; 陈晓冬; 何燕; 杨方; 曹宇宾; 潘大丰

    2011-01-01

    电子信息资源的整合是数字图书馆建设中的一个非常重要的环节,论述了数字资源整合的必要性,结合农业图书馆的实际,开展了电子资源整合服务平台的设计与实现。%The integration of electronic information resources is a very important part in digital library construction.In this paper,the necessity for integration of digital resources was discussed,combined with the actuality of the agricultural library,the design and implementation about services platform of electronic resource integration were carried out.

  20. Effect of grinding and heat treatment on the mechanical behavior of zirconia ceramic.

    Science.gov (United States)

    Ramos, Gabriela Freitas; Pereira, Gabriel Kalil Rocha; Amaral, Marina; Valandro, Luiz Felipe; Bottino, Marco Antonio

    2016-01-01

    The present study investigated the effect of grinding on roughness, flexural strength, and reliability of a zirconia ceramic before and after heat treatment. Seven groups were tested (n = 15): a control group (labeled CG, untreated), and six groups of samples ground with diamond discs, simulating diamond burs, with grits of 200 µm (G80); 160 µm (G120), and 25 µm (G600), either untreated or heat-treated at 1200°C for 2 h (labeled A). Yttria tetragonal zirconia polycrystal discs were manufactured, ground, and submitted to roughness and crystalline phase analyses before the biaxial flexural strength test. There was no correlation between roughness (Ra and Rz) and flexural strength. The reliability of the materials was not affected by grinding or heat treatment, but the characteristic strength was higher after abrasion with diamond discs, irrespective of grit size. The X-ray diffraction data showed that grinding leads to a higher monoclinic (m) phase content, whereas heat treatment produces reverse transformation, leading to a fraction of m-phase in ground samples similar to that observed in the control group. However, after heat treatment, only the G80A samples presented strength similar to that of the control group, while the other groups showed higher strength values. When zirconia pieces must be adjusted for clinical use, a smoother surface can be obtained by employing finer-grit diamond burs. Moreover, when the amount of monoclinic phase is related to the degradation of zirconia, the laboratory heat treatment of ground pieces is indicated for the reverse transformation of zirconia crystals.