Defense.gov Special Report: Fort Hood Shooting

Science.gov (United States)

identify possible insider threats, Army Secretary John M. McHugh told lawmakers. Story Obama: Soldiers ," Army Secretary John M. McHugh told lawmakers. Story President Praises Swift Response to Fort Hood Remarks on Fort Hood Shooting at White House McHugh, Odierno Address Fort Hood Shooting Before Congress

Management Observation Facility Fume Hoods

Energy Technology Data Exchange (ETDEWEB)

Sundsmo, V. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-05-17

I reviewed all the hoods used for AS&I work in buildings 253, 254, and 255. All have had the minimum annual surveys conducted and some have had semi-annual reviews. The operating parameter labels are posted consistent to the right or above right (with the only exception the perchloric acid hood in 1734- on the left) which facilitates users knowing where to check for information. All hoods with sash doors (except the SE one in 1734 have a note on the Operating Parameters label to "keep sash doors closed". Again, this was checking consistency. No surveys were missed.

Detection of Elemental Composition of Lubricating Grease Using Laser Induced Breakdown Spectroscopy

Directory of Open Access Journals (Sweden)

Cherry Dhiman

2014-12-01

Full Text Available The elemental composition of lubricating soft grease used in rail engines are studied using laser induced breakdown spectroscopy (LIBS technique. LIBS spectra of fresh, partially used and fully used grease samples are recorded using time-gated ICCD spectrometer for verification of compositional degradation of the used grease. LIBS spectra of grease samples are analyzed by comparing with emission spectra of elements published by NIST standard database. Many spectral lines of impurity elements like Fe, Cu, Ba, Mg, Mn, Ni, S, Zn, Si, Pb, Ti, Ca and Al present in the grease in ppm or ppb level in trace level concentrations are observed in excess in the used grease mainly due to wear and tear. On the other hand in fresh grease, spectral lines of Ca, Al and Na are observed predominantly.

Hood Canal Steelhead - Hood Canal Steelhead Supplementation Experiment

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Hood Canal Steelhead Project is a 17-year before-after-control-impact experiment that tests the effects of supplementation on natural steelhead populations in...

Eco-Friendly Multipurpose Lubricating Greases from Vegetable Residual Oils

Directory of Open Access Journals (Sweden)

Ponnekanti Nagendramma

2015-10-01

Full Text Available Environmentally friendly multipurpose grease formulation has been synthesized by using Jatropha vegetable residual oil with lithium soap and multifunctional additive. The thus obtained formulation was evaluated for its tribological performance on a four-ball tribo-tester. The anti-friction and anti-wear performance characteristics were evaluated using standard test methods. The biodegradability and toxicity of the base oil was assessed. The results indicate that the synthesized residual oil grease formulation shows superior tribological performance when compared to the commercial grease. On the basis of physico-chemical characterization and tribological performance the vegetable residual oil was found to have good potential for use as biodegradable multipurpose lubricating grease. In addition, the base oils are biodegradable and non toxic.

Accelerated Testing of UH-60 Viscous Bearings for Degraded Grease Fault

Science.gov (United States)

Dykas, Brian; Hood, Adrian; Krantz, Timothy; Klemmer, Marko

2015-01-01

An accelerated aging investigation of critical aviation bearings lubricated with MIL-PRF- 81322 grease was conducted to derive an understanding of the mechanisms of grease degradation and loss of lubrication over time. The current study focuses on UH-60 Black Hawk viscous damper bearings supporting the tail rotor driveshaft, which were subjected to more than 5800 hours of testing in a heated environment to accelerate the deterioration of the grease. The mechanism of grease degradation is a reduction in the oil/thickener ratio rather than the expected chemical degradation of grease constituents. Over the course of testing, vibration and temperature monitoring of bearings was conducted and trends for failing bearings are presented.

Optimization of the Hood of Diesel Electric Locomotive

Directory of Open Access Journals (Sweden)

Petr TOMEK

2013-06-01

Full Text Available The new construction of hood of diesel electric locomotive is analyzed in this paper. The whole construction is loaded by inertia effects caused by prescribed acceleration. The parts of the hood are subject to the standards for railway applications CSN EN 12663-1 [1]. Numerical analyses are performed by FEM computer program COSMOSWorks [2]. The original construction of hood is analyzed in first part of this paper. Structural changes are proposed in the next part of this article. Carrying capacity of the new construction of hood is verified by a numerical analysis. The results of the new construction are compared with the original construction of hood.

Effect of carbonyl iron particles composition on the physical characteristics of MR grease

Energy Technology Data Exchange (ETDEWEB)

Mohamad, Norzilawati, E-mail: mnorzilawati@gmail.com; Mazlan, Saiful Amri, E-mail: amri.kl@utm.my [Vehicle System Engineering, Malaysia – Japan International Institute of Technology, Universiti Teknologi Malaysia, Jalan Sultan Yahya Petra (Jalan Semarak), Kuala Lumpur, 54000 (Malaysia); Ubaidillah, E-mail: ubaidillah@uns.ac.id [Vehicle System Engineering, Malaysia – Japan International Institute of Technology, Universiti Teknologi Malaysia, Jalan Sultan Yahya Petra (Jalan Semarak), Kuala Lumpur, 54000 (Malaysia); Mechanical Engineering Department, Faculty of Engineering, Universitas Sebelas Maret, Jl. Ir. Sutami 36A, Kentingan, Surakarta, 57126, Central Java, Surakarta (Indonesia)

2016-03-29

Magnetorheological (MR) grease is an extension of the study of magnetorheological materials. The MR grease can help to reduce the particles sedimentation problem occurred in the MR fluids. Within this study, an effort has been taken to investigate the effect of different weight compositions of carbonyl iron particles on the physical and chemical characteristics of the MR grease under off-state condition (no magnetic field). The MR grease is prepared by mixing carbonyl iron particles having a size range of 1 to 10 µm with commercial NPC Highrex HD-3 grease. Characterizations of MR grease are investigated using Vibrating Sample Magnetometer (VSM), Environmental Scanning Electron Microscopy (ESEM), Differential Scanning Calorimeter (DSC) and rheometer. The dependency of carbonyl iron particles weight towards the magnetic properties of MR grease and other characterizations are investigated.

Brown Grease to Biodiesel Demonstration Project Report

Energy Technology Data Exchange (ETDEWEB)

San Francisco Public Utilities Commission; URS Corporation; Biofuels, Blackgold; Carollo Engineers

2013-01-30

Municipal wastewater treatment facilities have typically been limited to the role of accepting wastewater, treating it to required levels, and disposing of its treatment residuals. However, a new view is emerging which includes wastewater treatment facilities as regional resource recovery centers. This view is a direct result of increasingly stringent regulations, concerns over energy use, carbon footprint, and worldwide depletion of fossil fuel resources. Resources in wastewater include chemical and thermal energy, as well as nutrients, and water. A waste stream such as residual grease, which concentrates in the drainage from restaurants (referred to as Trap Waste), is a good example of a resource with an energy content that can be recovered for beneficial reuse. If left in wastewater, grease accumulates inside of the wastewater collection system and can lead to increased corrosion and pipe blockages that can cause wastewater overflows. Also, grease in wastewater that arrives at the treatment facility can impair the operation of preliminary treatment equipment and is only partly removed in the primary treatment process. In addition, residual grease increases the demand in treatment materials such as oxygen in the secondary treatment process. When disposed of in landfills, grease is likely to undergo anaerobic decay prior to landfill capping, resulting in the atmospheric release of methane, a greenhouse gas (GHG). This research project was therefore conceptualized and implemented by the San Francisco Public Utilities Commission (SFPUC) to test the feasibility of energy recovery from Trap Waste in the form of Biodiesel or Methane gas. The research goals are given below: To validate technology performance; To determine the costs and benefits [including economic, socioeconomic, and GHG emissions reduction] associated with co-locating this type of operation at a municipal wastewater treatment plant (WWTP); To develop a business case or model for replication of the

Tribological Performance of Some Pennzane(Registered Trademark) Based Greases for Vacuum Applications

Science.gov (United States)

Marchetti, Mario; Jones, William R., Jr.; Street, Kenneth W.; Wheeler, Donald; Dixon, Duane; Jansen, Mark J.; Kimura, Hiroshi

2002-01-01

Commercial greases for space applications usually fulfill the requirements imposed by the severe conditions of use. The main requirement is their ability to create an EHL film, boundary film, or both under speed, load and temperature conditions that the mechanisms will operate. Three greases, all based on a multiply alkylated cyclopentane (Pennzan(R)) base oil, were studied. The thickeners were an n-octadecylterephthalamate soap, a lithium soap, and a urea derivative. A Four-Ball Tribometer and a Spiral Orbit Tribometer were employed to evaluate the greases under ultrahigh vacuum. Results indicated that all three greases yielded very low wear rates and extended lifetimes. In addition, routine physical property data is reported for each grease.

Renewable Energy Opportunities at Fort Hood, Texas

Energy Technology Data Exchange (ETDEWEB)

Solana, Amy E.; Warwick, William M.; Orrell, Alice C.; Russo, Bryan J.; Parker, Kyle R.; Weimar, Mark R.; Horner, Jacob A.; Manning, Anathea

2011-11-14

This report presents the results of Pacific Northwest National Laboratory's (PNNL) follow-on renewable energy (RE) assessment of Fort Hood. Fort Hood receives many solicitations from renewable energy vendors who are interested in doing projects on site. Based on specific requests from Fort Hood staff so they can better understand these proposals, and the results of PNNL's 2008 RE assessment of Fort Hood, the following resources were examined in this assessment: (1) Municipal solid waste (MSW) for waste-to-energy (WTE); (2) Wind; (3) Landfill gas; (4) Solar photovoltaics (PV); and (5) Shale gas. This report also examines the regulatory issues, development options, and environmental impacts for the promising RE resources, and includes a review of the RE market in Texas.

Research on a lubricating grease print process for cylindrical cylinder

Science.gov (United States)

Yang, Liu; Zhang, Xuan; Wang, XianYan; Tan, XiaoYan

2017-09-01

In vehicle braking system and clutch system of transmission, there is always a kind of cylindrical component dose reciprocating motion. The main working method is the reciprocating motion between the rubber sealing parts and cylindrical parts, the main factor affects the service life of the product is the lubricating performance of the moving parts. So the lubricating performance between cylinders and rubber sealing rings is particularly important, same as the quality of the grease applies on the surface of the surface of cylinder. Traditional method of manually applying grease has some defects such as applying unevenly, applying tools like brush and cloth easily falls off and affect the cleanness of products, contact skin easily cause allergy, waste grease due to the uncontrollable of grease quantity using in applying, low efficiency of manual operation. An automatic, quantitative and high pressure applying equipment is introduced in this document to replace the traditional manually applying method, which can guarantee the applying quality of the grease which are painted on the surface of cylinder and bring economic benefits to the company.

Lubricating grease shear flow and boundary layers in a concentric cylinder configuration

NARCIS (Netherlands)

Li, J.X.; Westerberg, L.G.; Höglund, E.; Lugt, Pieter Martin; Baart, P.

2014-01-01

Grease is extensively used to lubricate various machine elements such as rolling bearings, seals, and gears. Understanding the flow dynamics of grease is relevant for the prediction of grease distribution for optimum lubrication and for the migration of wear and contaminant particles. In this study,

Hood River production program monitoring and evaluation. Report B: Hood River and Pelton Ladder. Annual report 1996

International Nuclear Information System (INIS)

Lambert, M.B.; Jennings, M.; McCanna, J.P.

1996-01-01

The Hood River Production Program (HRPP) is jointly implemented by the Confederated Tribes of the Warm Springs Reservation of Oregon (CTWS) and the Oregon Department of Fish and Wildlife (ODFW). The primary goals of the HRPP are (1) to re-establish naturally sustaining spring chinook salmon using Deschutes River stock in the Hood River subbasin, (2) rebuild naturally sustaining runs of summer and winter steelhead in the Hood River subbasin, (3) maintain the genetic characteristics of the populations, and (4) contribute to tribal and non-tribal fisheries, ocean fisheries, and the Northwest Power Planning Council's (NPPC) interim goal of doubling salmon runs

Irradiation effect study on dynamic performance of grease

International Nuclear Information System (INIS)

Arakawa, Kazuo; Sasuga, Tsuneo; Hagiwara, Miyuki; Yajima, Toshio; Nakanishi, Hiroshi; Soda, Takao; Iwamoto, Takeshi.

1986-03-01

The radiation resistance of newly developed grease, MORESCO HIRAD RG-42-0, consisting of polyphenyl ether as base oil and inorganic compound as gelling agent was evaluated by conducting measurements of frictional resistance force on mechanical snubbers. After the irradiation of 60 Co γ-rays up to a predetermined dose [max. 100 MGy (10000 Mrad)], the grease was applied to mechanical snubbers. The rated load of mechanical snubbers used (standard stroke of 125 mm) was set at 0.16 ton and 1.0 ton. The frictional resistance force was measured at a velocity of 0.001, 0.01, 0.1 and 2.0 mm/sec and at temperature of 60 deg C. When the rated load was 0.16 ton, the frictional resistance force of irradiated grease was kept less than a criterion, a greater value of either 5 kgf or 1 % of the rated load, at every tested dose up to 90 MGy. In case of 1.0 ton, the frictional resistance force of the irradiated grease was less than a greater value of either 10 kgf or 1 % of the rated load at doses up to 70 MGy. (author)

Lubrication from mixture of boric acid with oils and greases

Science.gov (United States)

Erdemir, Ali

1995-01-01

Lubricating compositions including crystalline boric acid and a base lubricant selected from oils, greases and the like. The lubricity of conventional oils and greases can also be improved by adding concentrates of boric acid.

Impact of Water on the Rheology of Lubricating Greases

NARCIS (Netherlands)

Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

2016-01-01

The operational life of bearings is often determined by the performance of the lubricating grease. The consistency of the grease prevents it from leaking out of the bearing and provides good sealing properties. The possible ingress of water into the bearing will have a considerable impact not only

Removal of oil and grease from automobile garage wastewater using electrocoagulation

Science.gov (United States)

Manilal, A. M.; Harinarayanan Nampoothiri, M. G.; Soloman, P. A.

2017-06-01

Wastewater from automobile garages and workshops is an important contributor to the water pollution. Oil and grease is one of the major content of wastewater from vehicle garages. Wastewater from a public transport depot at Thrissur district in Kerala, India was collected for the study. A batch reactor has been devised to assess the efficacy of electrocoagulation in removing oil and grease from the wastewater. Aluminium and iron were tested as the anode material with stainless steel as cathode. Experiments were conducted to investigate the effect of various operating parameters such as current density, pH, time and salt concentration on oil and grease removal. The results shown that aluminium is superior to iron in removing the oil and grease from the wastewater. The reactor with aluminium as anode was able to remove 90.8 % of the oil and grease at a current density of 0.6 A/dm2 in 15 minutes. The calculated specific energy consumption is also less for aluminium in comparison with iron.

Effects of tallow, choice white grease, palm oil, corn oil, or soybean oil on apparent total tract digestibility of minerals in diets fed to growing pigs.

Science.gov (United States)

Merriman, L A; Walk, C L; Parsons, C M; Stein, H H

2016-10-01

An experiment was conducted to determine the effect of supplementing diets fed to growing pigs with fat sources differing in their composition of fatty acids on the apparent total tract digestibility (ATTD) of minerals. A diet based on corn, potato protein isolate, and 7% sucrose was formulated. Five additional diets that were similar to the previous diet with the exception that sucrose was replaced by 7% tallow, choice white grease, palm oil, corn oil, or soybean oil were also formulated. Diets were formulated to contain 0.70% Ca and 0.33% standardized total tract digestible P. Growing barrows ( = 60; 15.99 ± 1.48 kg initial BW) were allotted to a randomized complete block design with 2 blocks of 30 pigs, 6 dietary treatments, and 10 replicate pigs per treatment. Experimental diets were provided for 12 d with the initial 5 d being the adaptation period. Total feces were collected for a 5-d collection period using the marker-to-marker approach, and the ATTD of minerals, ether extract, and acid hydrolyzed ether extract was calculated for all diets. Digestibility of DM was greater ( soybean oil compared with the diet containing choice white grease or the basal diet, with all other diets being intermediate. The ATTD of Ca, S, and P was greater ( soybean oil, corn oil, palm oil, or tallow than for pigs fed the basal diet or the diet containing choice white grease. The ATTD of Mg, Zn, Mn, Na, and K were not different among dietary treatments. The ATTD of ether extract was greater ( oil, corn oil, or soybean oil compared with the diet containing choice white grease, and the ATTD of acid hydrolyzed ether extract in the diet containing soybean oil was also greater ( oil, corn oil, or soybean oil may increase the ATTD of some macrominerals, but that appears not to be the case if choice white grease is used. There was no evidence of negative effects of the fat sources used in this experiment on the ATTD of any minerals.

Use of Bio-Amp, a commercial bio-additive for the treatment of grease trap wastewater containing fat, oil, and grease.

Science.gov (United States)

Tang, Hao L; Xie, Yuefeng F; Chen, Yen-Chih

2012-11-01

This research investigated the application of Bio-Amp, a commercial bio-additive for the treatment of fat, oil, and grease (FOG) in a grease trap, and evaluated potential impacts of treated effluent on downstream collection system and treatment processes. Results show that after Bio-Amp treatment, FOG deposit formation was reduced by 40%, implicating a potential reduction of sewer line blockages. Chemical oxygen demand (COD), total nitrogen (TN), total phosphorus (TP) and total fatty acids were reduced by 39%, 33%, 56%, and 59%, respectively, which represents an overall loading reduction of 9% COD, 5% TN and 40% TP received by the treatment plant from all the dining halls. On the other hand, readily biodegradable COD fractions significantly increased, which implies a potential improvement on Bio-P removal. Overall, the results showed that application of Bio-Amp in grease trap provides potential reduction of sewer line blockages, and can also alleviate downstream treatment burden. Copyright © 2012 Elsevier Ltd. All rights reserved.

Study of physical and tribology properties of soybean oil-based grease formulated with polysoap

Science.gov (United States)

Soybean oil-based grease formulated with polysoaps, which was synthesized from polymeric epoxdized soybean oil, was investigated. Greases were prepared using a mixture of lithium soap and triethanolammonium polysoap. Grease properties investigated were: hardness, using cone penetration procedure (AS...

Evaluation of different polyolefins as rheology modifier additives in lubricating grease formulations

Energy Technology Data Exchange (ETDEWEB)

Martin-Alfonso, J.E.; Valencia, C.; Sanchez, M.C. [Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales, Universidad de Huelva, Campus Universitario del Carmen, 21071 Huelva (Spain); Franco, J.M., E-mail: franco@uhu.es [Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales, Universidad de Huelva, Campus Universitario del Carmen, 21071 Huelva (Spain); Gallegos, C. [Departamento de Ingenieria Quimica, Facultad de Ciencias Experimentales, Universidad de Huelva, Campus Universitario del Carmen, 21071 Huelva (Spain)

2011-08-15

Highlights: {yields} Evaluation of different polyolefins as modifiers of the rheological properties and mechanical stability of lithium lubricating greases. {yields} The type of polymer, molecular weight, cristallinity degree and vinyl acetate content influences the rheological and thermal response of lubricating greases. {yields} The crystallinity degree, mainly dependent on the nature of the polymer, is the most highly influencing parameter on the rheology of lubricating greases. {yields} The rheological modification exerted by EVA copolymers mainly depends on the vinyl acetate content. - Abstract: The purpose of the present work is to evaluate the effect that different polyolefins, used as additives in small proportions, exert on the rheological properties of standard lithium lubricating greases. Grease formulations containing several polyolefins, differing in nature and molecular weight, were manufactured and rheologically characterized. The influence of the type of polymer, molecular weight, crystallinity degree and vinyl acetate content has been analyzed. Small-amplitude oscillatory shear (SAOS) and viscous flow measurements, as well as calorimetric (DSC) and thermogravimetric (TGA) analysis, were carried out. In general, the addition of polymers such as HDPE, LDPE, LLDPE and PP to lithium lubricating greases significantly increases the values of the rheological parameters analyzed, consistency and mechanical stability. However, the use of polyolefins as rheology modifiers does not significantly affect the friction coefficient determined in a tribological contact. The crystallinity degree, mainly dependent on the nature of the polymer, has been found the most highly influencing parameter on the rheology of the lubricating greases studied. However, the rheological modification exerted by EVA copolymers mainly depends on the vinyl acetate content. Thus, a negative effect in both apparent viscosity and linear viscoelastic functions of greases was obtained when

San Francisco Biofuel Program: Brown Grease to Biodiesel Demonstration

Energy Technology Data Exchange (ETDEWEB)

Jolis, Domènec [San Francisco Public Utilities Commission, San Francisco, CA (United States); Martis, Mary [San Francisco Public Utilities Commission, San Francisco, CA (United States); Jones, Bonnie [San Francisco Public Utilities Commission, San Francisco, CA (United States); Miot, Alex [San Francisco Public Utilities Commission, San Francisco, CA (United States); Ving, Karri [San Francisco Public Utilities Commission, San Francisco, CA (United States); Sierra, Natalie [San Francisco Public Utilities Commission, San Francisco, CA (United States); Niobi, Morayo [San Francisco Public Utilities Commission, San Francisco, CA (United States)

2013-03-01

Municipal wastewater treatment facilities have typically been limited to the role of accepting wastewater, treating it to required levels, and disposing of its treatment residuals. However, a new view is emerging which includes wastewater treatment facilities as regional resource recovery centers. This view is a direct result of increasingly stringent regulations, concerns over energy use, carbon footprint, and worldwide depletion of fossil fuel resources. Resources in wastewater include chemical and thermal energy, as well as nutrients, and water. A waste stream such as residual grease, which concentrates in the drainage from restaurants (referred to as Trap Waste), is a good example of a resource with an energy content that can be recovered for beneficial reuse. If left in wastewater, grease accumulates inside of the wastewater collection system and can lead to increased corrosion and pipe blockages that can cause wastewater overflows. Also, grease in wastewater that arrives at the treatment facility can impair the operation of preliminary treatment equipment and is only partly removed in the primary treatment process. In addition, residual grease increases the demand in treatment materials such as oxygen in the secondary treatment process. When disposed of in landfills, grease is likely to undergo anaerobic decay prior to landfill capping, resulting in the atmospheric release of methane, a greenhouse gas (GHG). This research project was therefore conceptualized and implemented by the San Francisco Public Utilities Commission (SFPUC) to test the feasibility of energy recovery from Trap Waste in the form of Biodiesel or Methane gas.

Evaluation of flow hood measurements for residential register flows; TOPICAL

International Nuclear Information System (INIS)

Walker, I.S.; Wray, C.P.; Dickerhoff, D.J.; Sherman, M.H.

2001-01-01

Flow measurement at residential registers using flow hoods is becoming more common. These measurements are used to determine if the HVAC system is providing adequate comfort, appropriate flow over heat exchangers and in estimates of system energy losses. These HVAC system performance metrics are determined by using register measurements to find out if individual rooms are getting the correct airflow, and in estimates of total air handler flow and duct air leakage. The work discussed in this paper shows that commercially available flow hoods are poor at measuring flows in residential systems. There is also evidence in this and other studies that flow hoods can have significant errors even when used on the non-residential systems they were originally developed for. The measurement uncertainties arise from poor calibrations and the sensitivity of exiting flow hoods to non-uniformity of flows entering the device. The errors are usually large-on the order of 20% of measured flow, which is unacceptably high for most applications. Active flow hoods that have flow measurement devices that are insensitive to the entering airflow pattern were found to be clearly superior to commercially available flow hoods. In addition, it is clear that current calibration procedures for flow hoods may not take into account any field application problems and a new flow hood measurement standard should be developed to address this issue

Fat, oil and grease reduction in commercial kitchen ductwork: A novel biological approach.

Science.gov (United States)

Mudie, S; Vahdati, M

2017-03-01

Recent research has characterised emissions upon cooking a variety of foods in a commercial catering environment in terms of volume, particle size and composition. However, there has been limited focus on the deposition of solid grease in commercial kitchen ductwork, the sustainability of these systems and their implications on the heat recovery potential of kitchen ventilation extract air. This paper reviews the literature concerning grease, commonly referred to as Fat, Oils and Grease (FOG) abatement strategies and finds that many of these systems fall short of claimed performances. Furthermore these technologies often add to the energy cost of the operation and reduce the potential application of heat recovery in the ventilation ductwork. The aim of this study was to develop and evaluate a novel FOG removal system, with a focus on low environmental impact. The novel FOG removal system, utilises the biological activity of Bacillus subtilis and associated enzymes. The biological reagent is delivered via a misting system. The temperature, relative humidity and FOG deposit thickness were measured in the ductwork throughout a 3month trial period. FOG deposit thickness was reduced by 47% within 7weeks. The system was found to be effective at reducing the FOG deposit thickness with minimal energy cost and impact upon the kitchen and external environment. Internal ductwork operating temperature was measured with respect to future heat recovery potential and a reduction of 7°C was observed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Some azine and azole derivatives as antioxidant additives for lithium lubricating grease

Directory of Open Access Journals (Sweden)

Reda M. Fikry

2013-06-01

The structure of these compounds has been confirmed using elemental analysis, nuclear magnetic resonance and infrared spectroscopy. On the other hand, lithium lubricating grease was prepared and evaluated according to the National Lubricating Grease Institute (NLGI and Egyptian Standard (ES. The antioxidant compounds were tested for the prepared grease with concentration 0.1 wt.%. The efficiency of these compounds has been determined using total acid number. It was found that the prepared lithium grease resists oxidation reaction in the presence of these compounds. A correlation between the chemical structure of these compounds and their efficiency as antioxidants additives was discussed. Data showed that the efficiency of these compounds as antioxidants decreases in the order: compound I > compound II > compound III.

Improving flow patterns and spillage characteristics of a box-type commercial kitchen hood.

Science.gov (United States)

Huang, Rong Fung; Chen, Jia-Kun; Han, Meng-Ji; Priyambodo, Yusuf

2014-01-01

A conventional box-type commercial kitchen hood and its improved version (termed the "IQV commercial kitchen hood") were studied using the laser-assisted smoke flow visualization technique and tracer-gas (sulfur hexafluoride) detection methods. The laser-assisted smoke flow visualization technique qualitatively revealed the flow field of the hood and the areas apt for leakages of hood containment. The tracer-gas concentration detection method measured the quantitative leakage levels of the hood containment. The oil mists that were generated in the conventional box-type commercial kitchen hood leaked significantly into the environment from the areas near the front edges of ceiling and side walls. Around these areas, the boundary-layer separation occurred, inducing highly unsteady and turbulent recirculating flow, and leading to spillages of hood containment due to inappropriate aerodynamic design at the front edges of the ceiling and side walls. The tracer-gas concentration measurements on the conventional box-type commercial kitchen hood showed that the sulfur hexafluoride concentrations detected at the hood face attained very large values on an order of magnitude about 10(3)-10(4) ppb. By combining the backward-offset narrow suction slot, deflection plates, and quarter-circular arcs at the hood entrance, the IQV commercial kitchen hood presented a flow field containing four backward-inclined cyclone flow structures. The oil mists generated by cooking were coherently confined in these upward-rising cyclone flow structures and finally exhausted through the narrow suction slot. The tracer-gas concentration measurements on the IQV commercial kitchen hood showed that the order of magnitude of the sulfur hexafluoride concentrations detected at the hood face is negligibly small--only about 10(0) ppb across the whole hood face.

The Impact of Water on the Yield Stress and Startup Torque of Lubricating Greases

NARCIS (Netherlands)

Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

2017-01-01

Water is one of the most common contaminants in grease lubrication. There are numerous applications where bearings are susceptible to water ingresses such as in the steel, food, and pulp and paper industries. A grease can absorb water to different degrees depending upon the type of grease. The

Film Thickness and Friction Relationship in Grease Lubricated Rough Contacts

Directory of Open Access Journals (Sweden)

David Gonçalves

2017-08-01

Full Text Available The relationship between the film generation and the coefficient of friction in grease lubricated contacts was investigated. Ball-on-disc tests were performed under different operating conditions: entrainment speed, lubricant temperature and surface roughness. The tests were performed with fully formulated greases and their base oils. The greases were formulated with different thickener types and also different base oils natures and viscosities. Film thickness measurements were performed in ball-on-glass disc tests, and Stribeck curves were measured in ball-on-steel disc tests with discs of different roughness. The role of the thickener and the base oil nature/viscosity on the film thickness and coefficient of friction was addressed and the greases’ performance was compared based on their formulation.

Pilgrim Souvenir: Hood of Cherries

Directory of Open Access Journals (Sweden)

Amy Jeffs

2017-06-01

Full Text Available This lead alloy badge from the British Museum represents a medieval hood repurposed as a sack for a harvest of cherries. It measures 38 by 30 millimetres and was cast integrally with its pin and clasp in a three-part mould. When first made, it would have shone like silver. Badges were purchased in their millions by pilgrims between the late twelfth and early sixteenth centuries, as attractive, wearable and cheap souvenirs of their visits to holy sites. By the later Middle Ages badges were also worn as general symbols of devotion, as livery insignia, and as humorous or amorous tokens; which of these categories the “hood of cherries” badge falls into is debatable. Five of them have been found: three in Salisbury, and another in London, while the provenance of the fifth is unknown. Their cataloguers reluctantly associate them with the cult of St Dorothy, whose emblem is a basket of fruit, although Spencer expressed concern that, “a fashionable hood seems far removed from her story.” There are also possible alternative explanations to its meaning, which will be explored here.

BAURAN PEMASARAN PRODUK BARU PELUMAS FOOD GRADE GREASE BERBAHAN DaSAR MINYAK SAWIT

Directory of Open Access Journals (Sweden)

Ali Maksum

2016-12-01

Full Text Available Grease with food grade specification is essentially required on food processing production activities.  The purpose of this study is to develop a new product marketing mix for food grade grease, i.e 1 product priority, 2 pricing priority, 3 distribution priority and 4 advertising priority. This Research was conducted in Sub District Purbalingga and Padamara, Purbalingga regency with respondent SMEs food processing. Analysis of the determination of marketing mix that includes product, price, advertising and distribution using the Analytical Hierarchy Process (AHP. Sampling was purposive random sampling method with a population of 64 SMEs so drawn sample of 20 respondents. Result of the study showed the marketing mix priority which were: (1 advertising priority for the new food grade grease product with an ads that could attract the attention of consumers in order to made the consumers interested, tried, and bought the new food grade lubricating grease products. (2 Price priority for the new food grade grease products which was by determining the moderate prices to compete the competitors' prices while still maintained a high quality. (3 Product priority for new food grade grease product which was producing a qualified product which could withstand the wear of the engine, green colour of the product, a 350 g size packs with a rectangular shape packaging labels. (4 Distribution priority for the new food grade grease product which was a short distribution channels through mobile vendors so that the consumers were able to save costs, and got the product fast and easily

Field Demonstration for Biodegradable Military Multipurpose Grease

National Research Council Canada - National Science Library

Rhee, In-Sik

2001-01-01

Soils and ground water at many military facilities throughout the United States have been contaminated with petroleum based products, such as engine oils, greases, hydraulic fluids, and fuels, often...

Hooded Vulture Necrosyrtes monachus and African White-backed ...

African Journals Online (AJOL)

Basic ecological information is still lacking for many species of African vultures. The Hooded Vulture Necrosyrtes monachus is known as a rare breeding resident in north-eastern South Africa. This study set out to monitor the nests of Hooded Vultures and, secondarily, White-backed Vultures Gyps africanus in the Olifants ...

Visitors to nests of Hooded Vultures Necrosyrtes monachus in ...

African Journals Online (AJOL)

We recommend expanding the Hooded Vulture nest monitoring programme to include more pairs. Keywords: Alopochen aegyptiaca, Chacma Baboon, Egyptian Goose, Hooded Vulture, Kruger-to-Canyons Biosphere Region, Martial Eagle, Necrosyrtes monachus, nest visitors, Papio ursinus, Polemaetus bellicosus ...

The Field-Dependent Rheological Properties of Magnetorheological Grease Based on Carbonyl-Iron-Particles

Science.gov (United States)

Mohamad, N.; Mazlan, S. A.; Ubaidillah; Choi, Seung-Bok; Nordin, M. F. M.

2016-09-01

This paper presents dynamic viscoelastic properties of magnetorheological (MR) grease under variation of magnetic fields and magnetic particle fractions. The tests to discern the field-dependent properties are undertaken using both rotational and oscillatory shear rheometers. As a first step, the MR grease is developed by dispersing the carbonyl iron (CI) particles into grease medium with a mechanical stirrer. Experimental data are obtained by changing the magnetic field from 0 to 0.7 T at room temperature of 25 °C. It is found that a strong Payne effect limits the linear viscoelastic region of MR grease at strains above 0.1%. The results exhibit a high dynamic yield stress which is equivalent to Bingham plastic rheological model, and show relatively good MR effect at high shear rate of 2000 s-1. In addition, high dispersion of the magnetic particles and good thermal properties are proven. The results presented in this work directly indicate that MR grease is a smart material candidate that could be widely applicable to various fields including vibration control.

Fats, oils, and grease : options for plant-level treatment of a national problem

Energy Technology Data Exchange (ETDEWEB)

Miles, E.; Scherffius, B. [EcoPlus Inc. Charlotte, NC (United States)

2007-09-15

Fats, oils, and grease from restaurants and homes can congeal in sewers and result in damaging runoff into rivers and streams. A growing number of food service establishments are now producing increasing amounts of a specific grease product called brown grease, which is sticky and difficult to remove. Regulations now require haulers to remove the waste and dispose of it. However, many local treatment plants cannot accept or dispose of the amounts of grease currently being produced. A total of volume of 3 to 10 billion gallons per year of contaminated water have been accidentally discharged from sanitary sewers as a result of brown grease accumulations. This paper provided details of the EcoPlus Final Treatment Facility, which can be set up at waste water treatment plants and is able to process brown grease and discharge supernatant water from its process back into city sewers. The EcoPlus process produces 2 waste streams: (1) a low strength aqueous solution that can be disposed of in a sanitary sewer tap; and (2) a granular material that can be disposed of in a landfill for use as a soil conditioner. It was concluded that the granular material can also be used facilitate the incineration of sewage sludge, or burned as an alternative green fuel for power generation. 4 figs.

Study on thermal effects & sulfurized additives, in lubricating greases

Science.gov (United States)

Shah, Ami Atul

Lithium Base grease constitutes about 50% of market. The greases are developed to be able to work in multiple working conditions and have longer working life. Greases with extreme pressure additives and anti-wear additives have been developed as a solution to many of the applications. These developed greases are tested under ASTM D2266 testing conditions to meet the requirements. The actual working conditions, although, differ than the real testing conditions. The loading, speed and temperature conditions can be more harsh, or fluctuating in nature. The cyclic nature of the parameters cannot be directly related to the test performance. For this purpose studies on the performance under spectrum loading, variable speed and fluctuating temperature must be performed. This study includes tests to understand the effect of thermal variation on some of the most commonly used grease additives that perform well under ASTM D2266 testing conditions. The studied additives include most widely used industrial extreme pressure additive MoS2. Performance of ZDDP which is trying to replace MoS2 in its industrial applications has also been studied. The tests cover study of extreme pressure, anti-wear and friction modifier additives to get a general idea on the effects of thermal variation in three areas. Sulphur is the most common extreme pressure additive. Sulphur based MoS 2 is extensively used grease additive. Study to understand the tribological performance of this additive through wear testing and SEM/EDX studies has been done. This performance is also studied for other metallic sulfides like WS2 and sulphur based organic compound. The aim is to study the importance of the type of bond that sulphur shares in its additive's structure on its performance. The MoS2 film formation is found to be on the basis of the FeS formation on the substrate and protection through sacrificial monolayer deposition of the MoS2 sheared structure. The free Mo then tends to oxidise. An attempt to

Measurements of Capture Efficiency of Range Hoods in Homes

DEFF Research Database (Denmark)

Simone, Angela; Sherman, Max H.; Walker, Iain S.

2015-01-01

mapped the pollution distribution in the room, and showed that the pollutants escape more at the sides of the cooktop. These preliminary results suggest that more measurements should be conducted investigating the capture efficiency at different pollutant source temperature, size and location...... want a range hood to use little energy and have high capture efficiency to minimize the required air flow to capture the cooking pollutants. Currently there are no standards for rating range hoods for capture efficiency In this study, measurements of range hood capture efficiency were made a tight...... kitchen-room built in a laboratory chamber, and a methodology for standardizing measurement of capture efficiency was developed. The results for a wall mounted range hood, showed that up to half of the cooking pollutants were not captured at a flow rate of 230 m3/h. A more detailed set of measurements...

Rheological Behavior of Carbon Nanotubes as an Additive on Lithium Grease

Directory of Open Access Journals (Sweden)

Alaa Mohamed

2013-01-01

Full Text Available The rheological behaviors of carbon nanotubes (CNTs as an additive on lithium grease at different concentrations were examined under various settings of shear rate, shear stress, and apparent viscosity. The results indicated that the optimum content of the CNTs was 2%. These experimental investigations were evaluated with a Brookfield Programmable Rheometer DV-III ULTRA. The results indicated that the shear, stress and apparent viscosity increase with the increase of CNTs concentration. The microstructure of CNTs and lithium grease was examined by high resolution transmission electron microscope (HRTEM and scanning electron microscope (SEM. The results indicated that the microscopic structure of the lithium grease presents a more regular and homogeneous network structure, with long fibers, which confirms the rheological stability.

Design and application on experimental platform for high-speed bearing with grease lubrication

Directory of Open Access Journals (Sweden)

He Qiang

2015-12-01

Full Text Available The experimental platform for high-speed grease is an important tool for research and development of high-speed motorized spindle with grease lubrication. In this article, the experimental platform for high-speed grease is designed and manufactured which consists of the drive system, the test portion, the loading system, the lubrication system, the control system, and so on. In the meantime, the high-speed angular contact ceramic ball bearings B7005C/HQ1P4 as the research object are tested and contrasted in the grease lubrication and oil mist lubrication. The experimental platform performance is validated by contrast experiment, and the high-speed lubricated bearing performance is also studied especially in the relationship among the rotating speed,load and temperature rise. The results show that the experimental platform works steadily, accurate, and reliable in the experimental testing. And the grease lubrication ceramic ball bearings B7005C/HQ1P4 can be used in high-speed motorized spindle in the circular water cooling conditions when the rotating speed is lower than 40,000 r/min or the DN value (the value of the bearing diameter times the rotating speed is lower than the 1.44 × 106 mm r/min. Grease lubrication instead of oil mist lubrication under high-speed rotating will simplify the structure design of the high-speed motorized spindle and reduce the pollution to the environment.

Effect of flow characteristics on ultrafine particle emissions from range hoods.

Science.gov (United States)

Tseng, Li-Ching; Chen, Chih-Chieh

2013-08-01

In order to understand the physical mechanisms of the production of nanometer-sized particulate generated from cooking oils, the ventilation of kitchen hoods was studied by determining the particle concentration, particle size distribution, particle dimensions, and hood's flow characteristics under several cooking scenarios. This research varied the temperature of the frying operation on one cooking operation, with three kinds of commercial cooking oils including soybean oil, olive oil, and sunflower oil. The variations of particle concentration and size distributions with the elevated cooking oil temperatures were presented. The particle concentration increases as a function of temperature. For oil temperatures ranging between 180°C and 210°C, a 5°C increase in temperature increased the number concentration of ultrafine particles by 20-50%. The maximum concentration of ultrafine particles was found to be approximately 6 × 10(6) particles per cm(3) at 260°C. Flow visualization techniques and particle distribution measurement were performed for two types of hood designs, a wall-mounted range hood and an island hood, at a suction flow rate of 15 m(3) min(-1). The flow visualization results showed that different configurations of kitchen hoods induce different aerodynamic characteristics. By comparing the results of flow visualizations and nanoparticle measurements, it was found that the areas with large-scale turbulent vortices are more prone to dispersion of ultrafine particle leakage because of the complex interaction between the shear layers and the suction movement that results from turbulent dispersion. We conclude that the evolution of ultrafine particle concentration fluctuations is strongly affected by the location of the hood, which can alter the aerodynamic features. We suggest that there is a correlation between flow characteristics and amount of contaminant leakage. This provides a comprehensive strategy to evaluate the effectiveness of kitchen hoods

Effects of boundary-layer separation controllers on a desktop fume hood.

Science.gov (United States)

Huang, Rong Fung; Chen, Jia-Kun; Hsu, Ching Min; Hung, Shuo-Fu

2016-10-02

A desktop fume hood installed with an innovative design of flow boundary-layer separation controllers on the leading edges of the side plates, work surface, and corners was developed and characterized for its flow and containment leakage characteristics. The geometric features of the developed desktop fume hood included a rearward offset suction slot, two side plates, two side-plate boundary-layer separation controllers on the leading edges of the side plates, a slanted surface on the leading edge of the work surface, and two small triangular plates on the upper left and right corners of the hood face. The flow characteristics were examined using the laser-assisted smoke flow visualization technique. The containment leakages were measured by the tracer gas (sulphur hexafluoride) detection method on the hood face plane with a mannequin installed in front of the hood. The results of flow visualization showed that the smoke dispersions induced by the boundary-layer separations on the leading edges of the side plates and work surface, as well as the three-dimensional complex flows on the upper-left and -right corners of the hood face, were effectively alleviated by the boundary-layer separation controllers. The results of the tracer gas detection method with a mannequin standing in front of the hood showed that the leakage levels were negligibly small (≤0.003 ppm) at low face velocities (≥0.19 m/s).

Ethanol intake and 3H-serotonin uptake I: A study in Fawn-Hooded rats

International Nuclear Information System (INIS)

Daoust, M.; Compagnon, P.; Legrand, E.; Boucly, P.

1991-01-01

Ethanol intake and synaptosomal 3 H-serotonin uptake were studied in male Fawn-Hooded and Sprague-Dawley rats. Fawn-Hooded rats consumed more alcohol and more water than Sprague-Dawley rats. Plasma alcohol levels of Sprague-Dawley rats were not detectable but were about 5 mg/dl in Fawn-Hooded rats. Ethanol intake increased the Vmax of serotonin uptake in Fawn-Hooded rats in hippocampus and cortex, but not in thalamus. In Fawn-Hooded rats, serotonin uptake (Vmax) was higher than in Sprague-Dawley rats cortex. Ethanol intake reduced the Vmax of serotonin uptake in Fawn-Hooded rats in hippocampus and cortex. In cortex, the carrier affinity for serotonin was increased in alcoholized Fawn-Hooded rats. These results indicate that synaptosomal 3 H-serotonin uptake is affected by ethanol intake. In Fawn-Hooded rats, high ethanol consumption is associated with high serotonin uptake. In rats presenting high serotonin uptake, alcoholization reduces 3 H-serotonin internalization in synaptosomes, indicating a specific sensitivity to alcohol intake of serotonin uptake system

Effect of polysoap on physical and tribology properties of soybean oil-based grease

Science.gov (United States)

The overall objective of this work was to evaluate the evolution of soybean oil based grease containing polysoaps made from polymeric epoxdized soybean oil. With this aim, lubricating greases were prepared from a mixed soap comprising lithium soap and triethanol ammonium polysoap synthesized from so...

Minimum acceptable face velocities of laboratory fume hoods and guidelines for their classification

International Nuclear Information System (INIS)

Bolton, N.E.; Porter, W.E.; Alcorn, S.P.; Everett, W.S.; Hunt, J.B.; Morehead, J.F.; Higdon, H.F.

1978-06-01

Data developed to support the requirement of a 100 LFM minimum face velocity requirement for laboratory fume hoods are summarized. Also included is a description of the Y-12 test hood as well as guidelines for a hood classification scheme

Friction torque in thrust ball bearings grease lubricated

Science.gov (United States)

Ianuş, G.; Dumitraşcu, A. C.; Cârlescu, V.; Olaru, D. N.

2016-08-01

The authors investigated experimentally and theoretically the friction torque in a modified thrust ball bearing having only 3 balls operating at low axial load and lubricated with NGLI-00 and NGLI-2 greases. The experiments were made by using spin-down methodology and the results were compared with the theoretical values based on Biboulet&Houpert's rolling friction equations. Also, the results were compared with the theoretical values obtained with SKF friction model adapted for 3 balls. A very good correlation between experiments and Biboulet_&_Houpert's predicted results was obtained for the two greases. Also was observed that the theoretical values for the friction torque calculated with SKF model adapted for a thrust ball bearing having only 3 balls are smaller that the experimental values.

Effect of internal elements of the steam turbine exhaust hood on losses

Directory of Open Access Journals (Sweden)

Tajč Ladislav

2012-04-01

Full Text Available The document deals with the flow in the exhaust hood of a single flow steam turbine. The effect of the shape of the external case of the hood and the position and dimensions of the internal reinforcements on the energy loss coefficient is evaluated. Using this coefficient, it is possible to determine the gained or lost output in the diffuser and the entire exhaust hood at a known flow and efficiency of the last stage. Flow research in the exhaust hood was performed especially using numeric simulations; some variants were verified experimentally in the aerodynamic wind tunnel.

The potential of restaurant trap grease as biodiesel feedstock

Directory of Open Access Journals (Sweden)

Parichart Hasuntree

2011-10-01

Full Text Available The possibility of using restaurant trap grease as feedstock in the production of biodiesel via acid catalyzed esterificationis explored in this study. Sulfuric acid was used as a catalyst for the esterification reaction of free fatty acid (FFA andmethanol. The FFA levels of restaurant trap greases were reduced from 60.38±2.22 mg KOH/g to 11.60±1.60 mgKOH/g whenconditions for biodiesel production are as follow: methanol-to-FFA ratio of 5:1, 5 wt.% H2SO4, and a reaction temperature at60°C with a reaction time of 60 min. During the acid-catalyzed esterification, the percentage of methyl esters resulting fromconversion of FFA in the obtained product was 83.59±1.51% based on the result of 1H NMR analysis. Data obtained from the23 full factorial designs revealed that methanol-to-FFA ratio term had the most significant effect on the percentage of methylesters, followed by the H2SO4 concentration. Conversely, reaction time between 1 and 3 hours had no significant effect on theesterification of trap greases.

Hood River production program monitoring and evaluation. Report A: Hood River and Pelton Ladder evaluation studies. Annual report for 1996

International Nuclear Information System (INIS)

Olsen, E.A.; French, R.A.

1996-01-01

In 1992, the Northwest Power Planning Council approved the Hood River and Pelton Ladder master plans within the framework of the Columbia River Basin Fish and Wildlife Program. The master plans define an approach for implementing a hatchery supplementation program in the Hood River subbasin. The hatchery program, as defined in the master plans, is called the Hood River Production Program (HRPP). The HRPP will be implemented at a reduced hatchery production level until (1) the construction of all proposed hatchery facilities has been completed and (2) numbers of returning wild jack and adult fish are sufficient to meet broodstock collection goals. It is anticipated that construction on the hatchery production facilities will be completed by the spring of 1998. The HRPP is jointly implemented by the Oregon Department of Fish and Wildlife (ODFW) and the Confederated Tribes of the Warm Springs (CTWS) Reservation

Rheological Behavior of Carbon Nano tubes as an Additive on Lithium Grease

International Nuclear Information System (INIS)

Mohamed, A.; Zaki, M.; Mohamed, A.; Khattab, A.A.; Osman, T.A.

2013-01-01

The rheological behaviors of carbon nano tubes (CNTs) as an additive on lithium grease at different concentrations were examined under various settings of shear rate, shear stress, and apparent viscosity. The results indicated that the optimum content of the CNTs was 2%. These experimental investigations were evaluated with a Brookfield Programmable Rheometer DV-III ULTRA. The results indicated that the shear, stress and apparent viscosity increase with the increase of CNTs concentration. The microstructure of CNTs and lithium grease was examined by high resolution transmission electron microscope (HRTEM) and scanning electron microscope (SEM). The results indicated that the microscopic structure of the lithium grease presents a more regular and homogeneous network structure, with long fibers, which confirms the rheological stability.

Environmentally adjusted oil and grease

International Nuclear Information System (INIS)

Andersson, Bert; Lindberg, J.

1992-01-01

With the intention of maintaining healthy environment in our rivers Vattenfall in 1988 initiated a project called 'Environmentally friendly oils'. The goal was to find oils for bearings and hydraulic systems that would cause less negative environmental effects and still maintain a good technical function. Based on the results of the project it is recommended, for both economical and environmental reasons, to change to synthetic oil in bearings and to hydraulic oil made of white oil in regulating systems. The change may be carried out in connection to other work on the system in question. Special care is recommended when cleaning the system from old oil and dirt. In order to maintain the high quality of the oil, also during manufacturing and assembling, one should follow the recommendations outlined in the report. In bearings where used grease leaks into the river, a grease made of white oil should be used. The quality of the rubber sealings must be adapted to the oil used, in order to secure a good function. In order to bring down the number of products and to create an open market some additional changes is necessary in the specifications of oil. Further research regarding oil and sealing is planned. (3 refs.)

Enhancement of biogas production from sewage sludge by addition of grease trap sludge

International Nuclear Information System (INIS)

Grosser, A.; Neczaj, E.

2016-01-01

Highlights: • Addition of grease trap sludge is interesting option for sewage sludge digestion. • Co-digestion of grease trap sludge and sewage sludge improved efficiency of process. • The anaerobic digestion can be carried out at short hydraulic retention time. • Long chain fatty acids concentration was below the ranges for inhibition of anaerobic digestion. - Abstract: Despite having many benefits, a low degree of volatile solids removal as well as long retention time are the main factors limiting the performance of the anaerobic digestion. Co-digestion of sewage sludge with other organic waste (for example fat rich materials) is one of the few potential ways to enhance the performance of the anaerobic digestion. In this article, the effects of adding fatty rich materials on the performance and stability of semi-continuous anaerobic digestion of sewage sludge were investigated on a 6 l laboratory-scale reactor (working volume equal to 5.5 l). The reactor was operated in a semi-continuous mode with a hydraulic retention time of 10 days. The data presented in this paper relate to the period in which the grease trap sludge accounted for 10, 12, 14, 16 and 18% of the mixture on the volatile solids basis. The results clearly indicate that the addition of fat rich materials like grease trap sludge can lead to a satisfactory increase in biogas yield in digester treating sewage sludge. The results showed that co-digestion can enhance the biogas yield by 28–82% compared to anaerobic digestion of sewage sludge alone (control sample). Moreover, the addition of grease trap sludge to digesters resulted in increased volatile solids removal from 44.38% (control sample) to 57.77% (feedstock with 14% addition of grease trap sludge). It was found that the increase of grease trap sludge in the feedstock had a direct impact on the biogas production and methane yield. This proposal has also been confirmed by statistical analysis such as Pearson correlation coefficients and

The processing of used cooking oil (yellow grease) using combination of adsorption and ultrafiltration membrane processes

Science.gov (United States)

Rosnelly, C. M.; Sofyana; Amalia, D.; Sarah, S.

2018-03-01

Yellow grease is used cooking oil whose quality has degraded due to the oxidation, polymerization, or hydrolysis process. In previous studies, yellow grease refining had been conducted either by adsorption or by using membrane. In this study, adsorption process using adsorbent from bagasse activated with H3PO4 12.5%, and ultrafiltration using Polyethersulfone (PES) membrane were combined. In adsorption stage, several variation of bagasse mass was fed into 200 ml of yellow grease and stirred for 60 minutes at 60 rpm. Yellow grease produced from adsorption with best condition was then processed using ultrafiltration membran that is PES membran with concentration by 15 wt % with transmembrane pressure variation by 0.5; 1; 1.5; 2; and 2.5 Bar. Analysis of yellow grease characteristics before refined showed its acid number, peroxide number, iodine number, and water content respectively by 2.68 mgKOH/Kg; 5.97 Meq/Kg; 51,48; and 1.29%. Characteristics of yellow grease after adsorption at its best condition on the parameters of acid number, peroxide number, iodine number, and water content are respectively by 2.55 mgKOH/Kg; 4.19 Meq/Kg; 40,02; and 0.27%. Characteristics of yellow grease after ultrafiltration at its best condition on the parameters of acid number, peroxide number, iodine number, and water content are respectively by 1.12 mgKOH/Kg; 1.8 Meq/Kg; 41,36; and 0.02%. Combination of adsorption and ultrafiltration processes for yellow grease processing showed decreasing value on the parameters of acid number, peroxide number, and water content that conforms to the SNI quality standard, but has not been able to increase the iodine number.

Case study of the effectiveness of passive grease trap for management on domestic kitchen waste water

Science.gov (United States)

Nidzamuddin, M. Y.; Juffrizal, K.; Mustapha, F.; Zulfattah, Z. M.; Tan, C. F.; Taha, M. M.; Hidayah, I.; Hilwa, M. Z.

2015-05-01

Household waste, generally known as trash or garbage is mostly includes food wastes, product packaging, and other miscellaneous inorganic wastes that are coming from domestic household. Grease waste such as oil and fats can contaminate water and also clot on pipes provoking blockages. Thus, waste water from kitchen sink need a proper way of filtration. Grease trap developed in this paper is viable in trapping the grease residue. The experiments have been conducted in controlled environment and the objectives are to investigate the effectiveness of grease trap by proving the existence of retention time and the expected ratio of collected water and oil during experiment process using a prototype model.

Application of a Thermodynamic Concept for the Analysis of Structural Degradation of Soap Thickened Lubricating Greases

Directory of Open Access Journals (Sweden)

Erik Kuhn

2018-01-01

Full Text Available Lubricating greases are special lubricants with a wide range of application. The tribologically stressed grease is used as tribological system and finally modeled as an open thermodynamic system. This study investigated the phenomenon of self-optimization and applied to the process of shearing a grease. The conditions for self-optimization and the consequences of created dissipative structures are investigated according to the interpreted literature.

Field-trip guide to Mount Hood, Oregon, highlighting eruptive history and hazards

Science.gov (United States)

Scott, William E.; Gardner, Cynthia A.

2017-06-22

This guidebook describes stops of interest for a geological field trip around Mount Hood volcano. It was developed for the 2017 International Association of Volcanology and Chemistry of the Earth’s Interior (IAVCEI) Scientific Assembly in Portland, Oregon. The intent of this guidebook and accompanying contributions is to provide an overview of Mount Hood, including its chief geologic processes, magmatic system, eruptive history, local tectonics, and hazards, by visiting a variety of readily accessible localities. We also describe coeval, largely monogenetic, volcanoes in the region. Accompanying the field-trip guidebook are separately authored contributions that discuss in detail the Mount Hood magmatic system and its products and behavior (Kent and Koleszar, this volume); Mount Hood earthquakes and their relation to regional tectonics and the volcanic system (Thelen and Moran, this volume); and young surface faults cutting the broader Mount Hood area whose extent has come to light after acquisition of regional light detection and ranging coverage (Madin and others, this volume).The trip makes an approximately 175-mile (280-kilometer) clockwise loop around Mount Hood, starting and ending in Portland. The route heads east on Interstate 84 through the Columbia River Gorge National Scenic Area. The guidebook points out only a few conspicuous features of note in the gorge, but many other guides to the gorge are available. The route continues south on the Mount Hood National Scenic Byway on Oregon Route 35 following Hood River, and returns to Portland on U.S. Highway 26 following Sandy River. The route traverses rocks as old as the early Miocene Eagle Creek Formation and overlying Columbia River Basalt Group of middle Miocene age, but chiefly lava flows and clastic products of arc volcanism of late Miocene to Holocene age.

Finite element analysis of car hood for impact test by using ...

African Journals Online (AJOL)

Finite element analysis of car hood for impact test by using solidworks software ... high safety and at the same time can be built according to market demands. ... Keywords: finite element analysis; impact test; Solidworks; automation, car hood.

Hood River and Pelton Ladder monitoring and evaluation project and Hood River fish habitat project : annual progress report 1999-2000.; ANNUAL

International Nuclear Information System (INIS)

Lambert, Michael B.; McCanna, Joseph P.; Jennings, Mick

2001-01-01

The Hood River subbasin is home to four species of anadromous salmonids: chinook salmon (Oncorhynchus tshawytscha), coho salmon (Oncorhynchus kisutch), steelhead (Oncorhynchus mykiss), and sea run cutthroat trout (Salmo clarki). Indigenous spring chinook salmon were extirpated during the late 1960's. The naturally spawning spring chinook salmon currently present in the subbasin are progeny of Deschutes stock. Historically, the Hood River subbasin hatchery steelhead program utilized out-of-basin stocks for many years. Indigenous stocks of summer and winter steelhead were listed in March 1998 by National Marine Fisheries Service (NMFS) under the Endangered Species Act (ESA) as a ''Threatened'' Species along with similar genetically similar steelhead in the Lower Columbia Basin. This annual report summarizes work for two consecutive contract periods: the fiscal year (FY) 1999 contract period was 1 October, 1998 through 30 September, 1999 and 1 October, 1999 through 30 September, 2000 for FY 2000. Work implemented during FY 1999 and FY 2000 included (1) acclimation of hatchery spring chinook salmon and hatchery summer and winter steelhead smolts, (2) spring chinook salmon spawning ground surveys on the West Fork Hood River (3) genetic analysis of steelhead and cutthroat[contractual service with the ODFW], (4) Hood River water temperature studies, (5) Oak Springs Hatchery (OSH) and Round Butte Hatchery (RBH) coded-wire tagging and clipping evaluation, (6) preparation of the Hood River Watershed Assessment (Coccoli et al., December 1999) and the Fish Habitat Protection, Restoration, and Monitoring Plan (Coccoli et al., February 2000), (7) project implementation of early action habitat protection and restoration projects, (8) Pelton Ladder evaluation studies, (9) management oversight and guidance to BPA and ODFW engineering on HRPP facilities, and (10) preparation of an annual report summarizing project objectives for FY 1999 and FY 2000

Removal (and attempted removal) of material from a Hooded Vulture ...

African Journals Online (AJOL)

Relatively little is documented about nest material theft in vultures. We used camera traps to monitor Hooded Vulture Necrosyrtes monachus nests for a year. We report camera trap photographs of a starling Lamprotornis sp. removing what appeared to be dung from an inactive Hooded Vulture nest on Cleveland Game ...

A study of the use of bio-based technologies (lubricant and grease) in rail applications.

Science.gov (United States)

2014-05-01

The objective of the project was to study the efficacy of using bio-based lubricant and grease technologies in railroad applications : (locomotives and maintenance of way equipment). Several commercially available rail curve greases were identified a...

Analysis of heat transfer and contaminant transport in fume hoods

International Nuclear Information System (INIS)

Pathanjali, C.; Rahman, M.M.

1996-01-01

The paper presents the analysis of three-dimensional flow patterns and the associated heat and mass transfer mechanisms in a fume hood enclosure. The flow enters the hood through the front window opening (positive x-direction) and leaves the cupboard through an opening on the top of the hood (positive z-direction). The flow was assumed to be fully turbulent. The flow pattern for different sash openings were studied. The flow pattern around an object located at the bottom of the hood was studied for different locations of the object. It was found that air entering the hood proceeds directly to the back wall, impinges it and turns upward toward the top wall and exits through the outlet. The flow finds its way around any object forming a recirculating region at its training surface. With an increase in the sash opening, the velocity becomes higher and the fluid traces the path to the outlet more quickly. The volume occupied by recirculating flow decreases with increase in sash opening. Both temperature and concentration were found to be maximum near the source and gradually decreased as the heated air or gaseous contaminant entrained with incoming air. The local concentration decreased with increase in sash opening area. The results will be very useful to design experiments with optimum sash opening providing adequate disposal of contaminants with minimum use of conditioned air inside the room

"Ameeriklane" Robin Hood / Timo Diener

Index Scriptorium Estoniae

Diener, Timo

2005-01-01

Mängufilmi "Robin Hood : varaste prints" võtetest. Režissöör Kevin Reynolds, peaosas Kevin Costner, USA 1991. Järg: Teleleht nr. 14, 11. aprill 2005, lk. 38 : ill ja Teleleht nr. 15, 18. aprill 2005, lk. 38 : ill

Removal of Oil and Grease as Emerging Pollutants of Concern (EPC in Wastewater Stream

Directory of Open Access Journals (Sweden)

Alade Abass O

2011-12-01

Full Text Available Wastewater characteristics, which depend on wastewater source, are increasingly becoming more toxic in recent times. The concentrations of oil and grease in wastewater streams have been observed to increase in wastewater stream with increasing adverse effects on the ecology. This results from the increasing use of oil and grease in high-demanded oil-processed foods, establishment and expansion of oil mills and refineries worldwide, as well as indiscriminate discharge of oil and grease into the water drains, domestically and industrially. This study reports the applications, efficiencies and challenges of the wastewater treatment techniques currently employed in the removal of oil and grease from the industrial wastewater and municipal water stream. The results shows that the concentrations of oil and grease injected into the ecosystem are of higher environmental impact and this needs to be given the desired attention. The desired development for effective removal of oil and grease as emerging pollutants of concern (EPC in wastewater stream are thus proposed. ABSTRAK: Ciri-ciri air sisa, bergantung kepada punca air sisa tersebut, menjadi semakin toksik akhir-akhir ini. Kepekatan minyak dan gris dalam air sisa anak sungai dilihat makin bertambah dalam air sisa anak sungai dengan bertambahnya kesan negatif ke atas ekologi. Ini disebabkan oleh peningkatan penggunaan minyak dan gris dalam makanan berproses yang tinggi permintaannya, penubuhan dan perkembangan kilang pertroleum dan loji penapisan di seluruh dunia. Minyak dan gris juga dibuang sewenang-wenangnya ke dalam parit air, dari kalangan domestik dan industry. Kajian ini membentangkan tentang aplikasi, keberkesanan dan teknik cabaran rawatan air buangan yang kini digunakan dalam pembuangan minyak dan gris dari air sisa industry dan air sungai perbandaran. Keputusan menunjukkan kepekatan minyak dan gris yang wujud dibuang ke dalam ekosistem mempunyai impak yang lebih tinggi terhadap persekitaran

Influences of Restaurant Waste Fats and Oils (RWFO from Grease Trap as Binder on Rheological and Solvent Extraction Behavior in SS316L Metal Injection Molding

Directory of Open Access Journals (Sweden)

Mohd Halim Irwan Ibrahim

2016-02-01

Full Text Available This article deals with rheological and solvent extraction behavior of stainless steel 316L feedstocks using Restaurant Waste Fats and Oils (RWFO from grease traps as binder components along with Polypropylene (PP copolymer as a backbone binder. Optimal binder formulation and effect of solvent extraction variables on green compacts are being analyzed. Four binder formulations based on volumetric ratio/weight fraction between PP and RWFO being mixed with 60% volumetric powder loading of SS316L powder each as feedstock. The rheological analysis are based on viscosity, shear rate, temperature, activation energy, flow behavior index, and moldability index. The optimal feedstock formulation will be injected to form green compact to undergo the solvent extraction process. Solvent extraction variables are based on solvent temperature which are 40 °C, 50 °C, and 60 °C with different organic solvents of n-hexane and n-heptane. Analysis of the weight loss percentage and diffusion coefficient is done on the green compact during the solvent extraction process. Differential Scanning Calorimeter (DSC is used to confirm the extraction of the RWFO in green compacts. It is found that all binder fractions exhibit pseudoplastic behavior or shear thinning where the viscosity decreases with increasing shear rate. After considering the factors that affect the rheological characteristic of the binder formulation, feedstock with binder formulation of 20/20 volumetric ratio between PP and RWFO rise as the optimal binder. It is found that the n-hexane solvent requires less time for extracting the RWFO at the temperature of 60 °C as proved by its diffusion coefficient.

Nanoclays for polymer nanocomposites, paints, inks, greases

Indian Academy of Sciences (India)

... rheological modifier for paints, inks and greases, drug delivery vehicle for controlled release of therapeutic agents, and nanoclays for industrial waste water as well as potable water treatment to make further step into green environment. A little amount of nanoclay can alter the entire properties of polymers, paints, inks and ...

The Influence of Inlet Asymmetry on Steam Turbine Exhaust Hood Flows.

Science.gov (United States)

Burton, Zoe; Hogg, Simon; Ingram, Grant L

2014-04-01

It has been widely recognized for some decades that it is essential to accurately represent the strong coupling between the last stage blades (LSB) and the diffuser inlet, in order to correctly capture the flow through the exhaust hoods of steam turbine low pressure cylinders. This applies to any form of simulation of the flow, i.e., numerical or experimental. The exhaust hood flow structure is highly three-dimensional and appropriate coupling will enable the important influence of this asymmetry to be transferred to the rotor. This, however, presents challenges as the calculation size grows rapidly when the full annulus is calculated. The size of the simulation means researchers are constantly searching for methods to reduce the computational effort without compromising solution accuracy. However, this can result in excessive computational demands in numerical simulations. Unsteady full-annulus CFD calculation will remain infeasible for routine design calculations for the foreseeable future. More computationally efficient methods for coupling the unsteady rotor flow to the hood flow are required that bring computational expense within realizable limits while still maintaining sufficient accuracy for meaningful design calculations. Research activity in this area is focused on developing new methods and techniques to improve accuracy and reduce computational expense. A novel approach for coupling the turbine last stage to the exhaust hood employing the nonlinear harmonic (NLH) method is presented in this paper. The generic, IP free, exhaust hood and last stage blade geometries from Burton et al. (2012. "A Generic Low Pressure Exhaust Diffuser for Steam Turbine Research,"Proceedings of the ASME Turbo Expo, Copenhagen, Denmark, Paper No. GT2012-68485) that are representative of modern designs, are used to demonstrate the effectiveness of the method. This is achieved by comparing results obtained with the NLH to those obtained with a more conventional mixing

Greasing the Wheels of Trade

OpenAIRE

Hendrik P. van Dalen; Aico P. van Vuuren

2003-01-01

This discussion paper resulted in a publication in 'De Economist' , 2005, 153(2), 139-165. How much does a nation spend on resources to 'grease the wheels of trade'? To examine this question the Dutch economy is used as an exemplary case as the Netherlands are known as a nation of traders. This image was derived in the seventeenth century from successes in long distance trade, shipping and financial innovations. Despite its historical background in trading the potential to 'truck and barter' ...

Separation of oil and grease from oil sludge using surfactant

International Nuclear Information System (INIS)

Ainon Abdul Aziz; Syed Hakimi Sakuma Syed Ahmad; Zalina Laili

2005-01-01

The objective of the experiments was to observe the efficiency of the surfactant to remove oil and grease from oil sludges using various surfactant concentration ranging from 10 %, 15 %, 20 % and 30 %. The surfactant solution consists of two mixtures of Aqua 2000 and D Bond. The oil sludge were subjected to heating and surfactant treatment process. Remaining oil and grease concentration were observed on the oil sludges after treatment. Small scale experiments were conducted by heating process, without heating process and heating process with addition of sodium chloride. Surfactant solution was added in each process. Results shows that there is separation of oil and grease from the oil sludges. There were formation of mini emulsions (oil in water). The higher the concentration of surfactant used, the higher the concentrations of mini emulsion formed as observed. Solid remains after the treatment process were found to contain lesser oil concentration with presence of bitumen, sediment, organic and inorganic materials. After a washing process using distilled water, the solid was still black but less oily than before the treatment. There is no separation of oil occurred in aqueous solution for the control experiment. (Author)

An Electrochemical Processing Strategy for Improving Tribological Performance of Aisi 316 Stainless Steel Under Grease Lubrication

Science.gov (United States)

Zou, Jiaojuan; Li, Maolin; Lin, Naiming; Zhang, Xiangyu; Qin, Lin; Tang, Bin

2014-12-01

In order to improve the tribological performance of AISI 316 stainless steel (316 SS) under grease lubrication, electrochemical processing was conducted on it to obtain a rough (surface texturing-like) surface by making use of the high sensitivity of austenitic stainless steel to pitting corrosion in Cl--rich environment. Numerous corrosion pits or micro-ditches acted as micro-reservoirs on the obtained surface. While the grease could offer consistent lubrication, and then improve the tribological performance of 316 SS. Tribological behaviors of raw 316 SS and the treated sample were measured using a reciprocating type tribometer sliding against GCr15 steel counterpart under dry and grease lubrication conditions. The results showed that the mass losses of the two samples were in the same order of magnitude, and the raw sample exhibited lower friction coefficient in dry sliding. When the tests were conducted under grease lubrication condition, the friction coefficients and mass losses of the treated sample were far lower than those of the raw 316 SS. The tribological performance of 316 SS under grease lubrication was drastically improved after electrochemical processing.

Hood River Production Program Review, Final Report 1991-2001.

Energy Technology Data Exchange (ETDEWEB)

Underwood, Keith; Chapman, Colin; Ackerman, Nicklaus

2003-12-01

This document provides a comprehensive review of Bonneville Power Administration (BPA) funded activities within the Hood River Basin from 1991 to 2001. These activities, known as the Hood River Production Program (HRPP), are intended to mitigate for fish losses related to operation of federal dams in the Columbia River Basin, and to contribute to recovery of endangered and/or threatened salmon and steelhead, as directed by Nation Oceanic and Atmospheric Administration - Fisheries (NOAA Fisheries). The Environmental Impact Statement (EIS) for the HRPP, which authorized BPA to fund salmon and steelhead enhancement activities in the Hood River Basin, was completed in 1996 (BPA 1996). The EIS specified seven years of monitoring and evaluation (1996-2002) after program implementation to determine if program actions needed modification to meet program objectives. The EIS also called for a program review after 2002, that review is reported here.

Determination of the internal exposure hazard from plutonium work in an open front hood

Science.gov (United States)

Olson, Cheryl Lynn

Work with hazardous substances, such as radioactive material, can be done safely when engineered controls are used to maintain the worker effective dose below the International Commission on Radiological Protection ICRP 60 recommendation of 0.02 Sv/year and reduce the worker exposure to material to as low as reasonably achievable (ALARA). A primary engineered control used at a Los Alamos National Laboratory facility is the open-front hood. An open-front hood, also known as an open-front box, is a laboratory containment box that is fully enclosed except for a 15-cm opening along the front of the box. This research involved collection of the aerosol escaping an open-front hood while PuO2 sample digestion was simulated. Sodium chloride was used as a surrogate to mimic the behavior of PuO2. The NaCl aerosol was binned as a function of median aerodynamic diameter using a Micro-orifice Uniform Deposit Impactor (MOUDI, MSP Corporation, Shoreview, MN) cascade impactor. Using neutron activation analysis (NAA) to measure the mass of material in each of the nine bins of the MOUDI, the mass median diameter of the escaping aerosol was determined. Using the mass median diameter and the total mass of the particle distribution, dose was calculated using ICRP 60 methodology. Experimental conditions mimicked a stationary worker and a worker moving her hands in and out of the open front hood. Measurements were also done in the hood for comparison. The effect of the hands moving in and out of the box was modeled. Information necessary for Computational Fluid Dynamics (CFD) modeling is given, such as volumetric flow rates out of the open front hood and into the experimental room, detailed sketches of the experimental set-up, and energy provided by the hot plate and worker. This research is unique as it measures particle size distribution from routine working conditions. Current research uses tracer gases or describes non-routine conditions. It is important to have results that mimic

Airborne nanoparticle exposures associated with the manual handling of nanoalumina and nanosilver in fume hoods

International Nuclear Information System (INIS)

Tsai, Su-Jung; Ada, Earl; Isaacs, Jacqueline A.; Ellenbecker, Michael J.

2009-01-01

Manual handling of nanoparticles is a fundamental task of most nanomaterial research; such handling may expose workers to ultrafine or nanoparticles. Recent studies confirm that exposures to ultrafine or nanoparticles produce adverse inflammatory responses in rodent lungs and such particles may translocate to other areas of the body, including the brain. An important method for protecting workers handling nanoparticles from exposure to airborne nanoparticles is the laboratory fume hood. Such hoods rely on the proper face velocity for optimum performance. In addition, several other hood design and operating factors can affect worker exposure. Handling experiments were performed to measure airborne particle concentration while handling nanoparticles in three fume hoods located in different buildings under a range of operating conditions. Nanoalumina and nanosilver were selected to perform handling experiments in the fume hoods. Air samples were also collected on polycarbonate membrane filters and particles were characterized by scanning electron microscopy. Handling tasks included transferring particles from beaker to beaker by spatula and by pouring. Measurement locations were the room background, the researcher's breathing zone and upstream and downstream from the handling location. Variable factors studied included hood design, transfer method, face velocity/sash location and material types. Airborne particle concentrations measured at breathing zone locations were analyzed to characterize exposure level. Statistics were used to test the correlation between data. The test results found that the handling of dry powders consisting of nano-sized particles inside laboratory fume hoods can result in a significant release of airborne nanoparticles from the fume hood into the laboratory environment and the researcher's breathing zone. Many variables were found to affect the extent of particle release including hood design, hood operation (sash height, face velocity

Airborne nanoparticle exposures associated with the manual handling of nanoalumina and nanosilver in fume hoods

Energy Technology Data Exchange (ETDEWEB)

Tsai, Su-Jung, E-mail: candace.umass@gmail.com; Ada, Earl [University of Massachusetts Lowell, NSF Center for High-rate Nanomanufacturing (CHN) (United States); Isaacs, Jacqueline A. [Northeastern University, NSF Center for High-rate Nanomanufacturing (CHN) (United States); Ellenbecker, Michael J. [University of Massachusetts Lowell, NSF Center for High-rate Nanomanufacturing (CHN) (United States)

2009-01-15

Manual handling of nanoparticles is a fundamental task of most nanomaterial research; such handling may expose workers to ultrafine or nanoparticles. Recent studies confirm that exposures to ultrafine or nanoparticles produce adverse inflammatory responses in rodent lungs and such particles may translocate to other areas of the body, including the brain. An important method for protecting workers handling nanoparticles from exposure to airborne nanoparticles is the laboratory fume hood. Such hoods rely on the proper face velocity for optimum performance. In addition, several other hood design and operating factors can affect worker exposure. Handling experiments were performed to measure airborne particle concentration while handling nanoparticles in three fume hoods located in different buildings under a range of operating conditions. Nanoalumina and nanosilver were selected to perform handling experiments in the fume hoods. Air samples were also collected on polycarbonate membrane filters and particles were characterized by scanning electron microscopy. Handling tasks included transferring particles from beaker to beaker by spatula and by pouring. Measurement locations were the room background, the researcher's breathing zone and upstream and downstream from the handling location. Variable factors studied included hood design, transfer method, face velocity/sash location and material types. Airborne particle concentrations measured at breathing zone locations were analyzed to characterize exposure level. Statistics were used to test the correlation between data. The test results found that the handling of dry powders consisting of nano-sized particles inside laboratory fume hoods can result in a significant release of airborne nanoparticles from the fume hood into the laboratory environment and the researcher's breathing zone. Many variables were found to affect the extent of particle release including hood design, hood operation (sash height, face

Influence of Base Oil Polarity on the Transient Shear Flow of Biodegradable Lubricating Greases

Directory of Open Access Journals (Sweden)

Martin Fiedler

2015-09-01

Full Text Available The scope of this study is to elucidate the physical mechanisms influencing the transient flow behavior of lubricating greases based on biogenic oleochemicals from a polarity point of view. This includes the mutually interacting influence of base oil polarity and thickening agents on the rheologically-measured mechanical structural degradation in transient shear flow. Due to the high temperature dependence of Keesom forces in the background of polar-active bond mechanisms, the analysis of the transient flow response as a function of temperature allows to attribute the observed influences to differences in base oil polarity. In general, clay-thickened greases show a greater tendency to be rheologically influenced by base oil polarities than soap-thickened lubricating greases.

Removal of oil, grease, and suspended solids from produced water with ceramic crossflow microfiltration

International Nuclear Information System (INIS)

Chen, A.S.C.; Flynn, J.T.; Cook, R.G.; Casaday, A.L.

1991-01-01

In this paper results of studies of two onshore and two offshore pilot plants that use ceramic crossflow microfiltration (CCFM) to separate oil, grease, and suspended solids from produced water are discussed. The method is capable of producing permeate quality with < =5 mg/L (detection limit) of dispersed oil and grease and <1 mg/L of suspended solids

Sexual aggression by intruders in hooded crow Corvus cornix

OpenAIRE

Zduniak, Piotr; Kosicki, Jakub Z.; Yosef, Reuven

2015-01-01

The hooded crow Corvus cornix is a west Palaearctic, solitary nesting, monogamous corvid. In the breeding season, populations are characterized by a social organization wherein breeding pairs are territorial and non-breeding individuals, called floaters, live in flocks. During a study of the breeding ecology of the hooded crow, conducted in a protected flooded area, we monitored nests with video cameras. We recorded two separate incidents when intruders attacked a female at the nest. We belie...

Physico-chemical characterization of grease interceptors with and without biological product addition.

Science.gov (United States)

He, Xia; Osborne, Jason; de los Reyes, Francis L

2012-03-01

Hardened and insoluble fat, oil, and grease (FOG) deposits are the primary cause of sewer line blockages leading to sanitary sewer overflows (SSOs). However, there have been very few long-term assessments of the physico-chemical characteristics of full-scale grease interceptors (GIs), the first "line of defense" against FOG buildup in sewer lines. In this study, we assessed the physico-chemical characteristics of two full-scale GIs (at a restaurant and a retirement community kitchen) over a one-year period. Statistically significant differences between bioaugmented and untreated cycles were detected for several chemical and physical properties. The treated cycles had lower BOD and COD at the grease interceptor outlet. While the combined data for all treated cycles did not show lower FOG concentrations in the GI outlet compared to the combined data for all untreated cycles, comparison of specific individual treated and untreated cycles show a positive effect due to the addition of product.

Effects of the free fatty acid content in yellow grease on performance, carcass characteristics, and serum lipids in broilers.

Science.gov (United States)

Wu, H; Gong, L M; Guo, L; Zhang, L Y; Li, J T

2011-09-01

This study was conducted to investigate whether the free fatty acid (FFA) content of yellow grease would influence the performance and carcass characteristics of broiler chicks. A total of 432 one-day-old, male Arbor Acres broilers were randomly allotted to 1 of 4 treatments, with each treatment being applied to 6 pens of 18 chicks. The dietary treatments were based on corn and soybean meal and were supplemented with either soybean oil (2.86% FFA) or yellow grease with a low (2.74%), medium (12.59%), or high (19.05%) FFA content. The fat sources were supplemented at 1.5% of the diet during the starter phase (0 to 21 d) and at 3.0% of the diet during the grower phase (22 to 42 d). From d 0 to 42, the BW gains of chicks fed diets containing soybean oil and yellow grease with 2.74% FFA were similar. As the FFA level in the yellow grease increased, the BW gain of chicks decreased (P dressing percentage and the percentage of breast muscle in the carcass were significantly (P < 0.01) lower for broilers fed any yellow grease diet compared with birds fed soybean oil. In contrast, abdominal fat was significantly increased in diets containing yellow grease. These results demonstrate that the performance of birds fed yellow grease with a low content of FFA was essentially equal to that of birds fed soybean oil. However, because yellow grease samples containing FFA levels greater than 2.74% negatively affected bird performance, producers should exercise caution with regard to feeding broilers yellow grease with an elevated FFA content. In 42-d-old broilers, serum total cholesterol and low-density lipoprotein cholesterol levels were elevated in birds fed yellow grease, regardless of the dietary level. In contrast, serum high-density lipoprotein cholesterol and triglyceride levels were unaffected by dietary treatment. Although dietary FFA may influence triglyceride-rich lipoprotein metabolism in broilers, an explanation for the observed effects remains elusive.

Fort Hood Building and Landscape Inventory with WWII and Cold War Context

Science.gov (United States)

2007-03-01

barracks, 1970s (NARA)........................................................... 112 Figure 37. Palmer Movie Theater (NARA...revised 1953) showing layout of Hood Village and trailer park (Fort Hood...arms ammunition storage building #92012 (ERDC-CERL, 2004). ......... 260 Figure 163: Radio reception building #92063 (ERDC-CERL, 2004

Hood River and Pelton Ladder Evaluation Studies, Annual Report 2000-2001.

Energy Technology Data Exchange (ETDEWEB)

Olsen, Erik

2009-09-01

The Bonneville Power Administration (BPA) funded the development of two master plans which outline the rationale, and general approach, for implementing a defined group of projects that are an integral part of a comprehensive watershed goal to 'Protect, enhance and restore wild and natural populations of anadromous and resident fish within the Hood River Subbasin'. The Hood River Production Master Plan and the Pelton Ladder Master Plan were completed in 1991 and subsequently approved by the Northwest Power Planning Council in 1992. Action items identified in the two master plans, as well as in a later document entitled 'Hood River/Pelton Ladder Master Agreement' (ODFW and CTWSRO Undated), are designed to achieve two biological fish objectives: (1) to increase production of wild summer and winter steelhead (Oncorhynchus mykiss) to levels commensurate with the subbasins current carrying capacity and (2) re-establishing a self-sustaining population of spring chinook salmon (Oncorhynchus tshawytscha). Numerical fish objectives for subbasin escapement, spawner escapement, and subbasin harvest are defined for each of these species in Coccoli (2000). Several projects are presently funded by the BPA to achieve the Hood River subbasin's numerical fish objectives for summer and winter steelhead and spring chinook salmon. They include BPA project numbers 1998-021-00 (Hood River Fish Habitat), 1998-053-03 (Hood River Production Program - CTWSRO: M&E), 1998-053-07 (Parkdale Fish Facility), 1998-053-08 (Powerdale/Oak Springs O&M), and 1998-053-12 (Hood River Steelhead Genetics Study). Collectively, they are implemented under the umbrella of what has come to be defined as the Hood River Production Program (HRPP). The HRPP is jointly implemented by the Oregon Department of Fish and Wildlife (ODFW) and The Confederated Tribes of the Warm Springs Reservation of Oregon (CTWSRO). Strategies for achieving the HRPP's biological fish objectives for the Hood

Rheological Properties of Extreme Pressure Greases Measured Using a Process Control Rheometer

DEFF Research Database (Denmark)

Glasscock, Julie; Smith, Robin S.

2012-01-01

A new process control rheometer (PCR) designed for use in industrial process flows has been used to measure the rheological properties of three extreme-pressure greases. The rheometer is a robust yet sensitive instrument designed to operate in an industrial processing environment in either in......-line or on-line configurations. The PCR was able to measure the rheological properties including the elastic modulus, viscous modulus, and complex viscosity of the greases which in an industrial flow application could be used as variables in a feedback system to control the process and the quality...

Hood River Passive House

Energy Technology Data Exchange (ETDEWEB)

Hales, David [BA-PIRC, Spokane, WA (United States)

2014-01-01

The Hood River Passive Project was developed by Root Design Build of Hood River Oregon using the Passive House Planning Package (PHPP) to meet all of the requirements for certification under the European Passive House standards. The Passive House design approach has been gaining momentum among residential designers for custom homes and BEopt modeling indicates that these designs may actually exceed the goal of the U.S. Department of Energy's (DOE) Building America program to "reduce home energy use by 30%-50% (compared to 2009 energy codes for new homes). This report documents the short term test results of the Shift House and compares the results of PHPP and BEopt modeling of the project. The design includes high R-Value assemblies, extremely tight construction, high performance doors and windows, solar thermal DHW, heat recovery ventilation, moveable external shutters and a high performance ductless mini-split heat pump. Cost analysis indicates that many of the measures implemented in this project did not meet the BA standard for cost neutrality. The ductless mini-split heat pump, lighting and advanced air leakage control were the most cost effective measures. The future challenge will be to value engineer the performance levels indicated here in modeling using production based practices at a significantly lower cost.

The Effect of Condensing Steam Turbine Exhaust Hood Body Geometry on Exhaust Performance Efficiency

Science.gov (United States)

Gribin, V. G.; Paramonov, A. N.; Mitrokhova, O. M.

2018-06-01

The article presents data from combined numerical and experimental investigations of the effect that the overall dimensions of the exhaust hood of a steam turbine with an underslung condenser has on the aerodynamic losses in the hood. Owing to the properly selected minimum permissible overall dimensions of the exhaust hood, more efficient operation of this turbine component is achieved, better vibration stability of the turbine set shaft line is obtained, and lower costs are required for arranging the steam turbine plant in the turbine building. Experiments have shown that the main overall dimensions of the hood body have a determining effect on the exhaust hood flow path profile and on its aerodynamic performance. Owing to properly selected ratios between the exhaust hood body main sizes without a diffuser, a total loss coefficient equal to approximately unity has been obtained. By using an axial-radial diffuser, the energy loss can be decreased by 30-40% depending on the geometrical parameters and level of velocities in the inlet section of a hood having the optimal overall dimensions. By using the obtained results, it becomes possible to evaluate the overall dimensions necessary for achieving the maximal aerodynamic hood efficiency and, as a consequence, to obtain better technical and economic indicators of the turbine plant as a whole already at the initial stage of its designing. If a need arises to select overall dimensions smaller than their optimal values, the increase of energy loss can be estimated using the presented dependences. The cycle of investigations was carried out on the experimental setups available in the fundamental research laboratory of the Moscow Power Engineering Institute National University's Department of Steam and Gas Turbines with due regard to the operating parameters and similarity criteria.

Benzoxazole and Benzothiazole Antirust Greases. Work Unit Directive (WUD) 51

National Research Council Canada - National Science Library

Christian, John

1980-01-01

...) and polytetrafluoroethylene (PTFE) thickeners. Testing has shown that one percent concentrations of the additives in the grease formulations provide inhibition against rusting of ferrous metal components under conditions of high humidity...

The Influence of the Bed with a Semiopen Hood on Bacteria Removal in a Negative-Pressure Isolation Room

Directory of Open Access Journals (Sweden)

Jeng-Min Huang

2014-06-01

Full Text Available This study numerically investigates the influence of a sickbed with a semiopened hood on bacteria removal in a negative-pressure isolation room. The parameters include air change rate, lying style, the length and height of hood, flow rate allotments, and the positions of outlets. The results show that the hood has excellent effect on the removal of contaminated air, which is much better than the case without hood. The flow field of patient's face up cough is very different from face side cough, and the contaminated air cannot be removed properly through one air outlet. There are three outlets on the hood, set straight above the patient's face and at both sides. The allotment of the exhaust flow rate of the upper outlet to that of side outlets is suggested to be 4: 6. When the total air change rate is above 6 ACH, the hood length has slight influence on pollutant removal. The increase of hood height has a negative impact when the patient coughs lying on back. When the side exhaust flow rate is high, the hood height has a slight impact for face side cough. The recommended air change rate for the negative-pressure ward with sickbed hood is above 5 ACH.

Hood River Conservation Project load analysis

Energy Technology Data Exchange (ETDEWEB)

Stovall, T.K.

1987-11-01

As a part of the Hood River Conservation Project (HRCP), 314 homes were monitored to measure electrical energy use. The total electrical load, space heating load, water heating load (in about 200 homes), wood-stove heat output (in about 100 homes), and indoor temperature were monitored. Data were collected for one full year before and one full year after these homes were retrofit with conservation measures. Local weather information was also collected on a 15-min basis. This data base was used to evaluate the load savings attributable to HRCP. Two methods of weather normalization were used and showed close agreement. The weather-normalized diversified residential load savings on the Pacific Power and Light system and Hood River area peak days were >0.5 kW/household. The average spring, summer, and fall savings were much smaller, <0.1 kW/household. The load factor for the diversified residential load decreased following the conservation retrofit actions. 11 refs., 40 figs., 13 tabs.

Physical simulation technique on the behaviour of oil spills in grease ice under wave actions

International Nuclear Information System (INIS)

Li, Z.; Hollebone, B.; Fingas, M.; Fieldhouse, B.

2008-01-01

Light or medium oil spilled on ice tends to rise and remain the surface in unconsolidated frazil or grease ice. This study looked for a new system for studying the oil emulsion in grease ice under experimental conditions. A physical simulation technique was designed to test the effect of wave energy on the spilled oil grease ice emulsion. The newly developed test system has the ability to perform simulation tests in wave, wave-ice, wave-oil and wave-ice-oil. This paper presented the design concept of the developed test system and introduced the experimental certifications of its capability in terms of temperature control, wave-making and grease ice-making. The key feature of the technique is a mini wave flume which derives its wave making power from an oscillator in a chemical laboratory. Video cameras record the wave action in the flume in order to obtain wave parameters. The wave making capability tests in this study were used to determine the relation of wave height, length and frequency with oscillator power transfer, oscillator frequency and the depth of the water flume. 16 refs., 10 figs

Origins of albino and hooded rats: implications from molecular genetic analysis across modern laboratory rat strains.

Directory of Open Access Journals (Sweden)

Takashi Kuramoto

Full Text Available Albino and hooded (or piebald rats are one of the most frequently used laboratory animals for the past 150 years. Despite this fact, the origin of the albino mutation as well as the genetic basis of the hooded phenotype remained unclear. Recently, the albino mutation has been identified as the Arg299His missense mutation in the Tyrosinase gene and the hooded (H locus has been mapped to the ∼460-kb region in which only the Kit gene exists. Here, we surveyed 172 laboratory rat strains for the albino mutation and the hooded (h mutation that we identified by positional cloning approach to investigate possible genetic roots and relationships of albino and hooded rats. All of 117 existing laboratory albino rats shared the same albino missense mutation, indicating they had only one single ancestor. Genetic fine mapping followed by de novo sequencing of BAC inserts covering the H locus revealed that an endogenous retrovirus (ERV element was inserted into the first intron of the Kit gene where the hooded allele maps. A solitary long terminal repeat (LTR was found at the same position to the ERV insertion in another allele of the H locus, which causes the so called Irish (h(i phenotype. The ERV and the solitary LTR insertions were completely associated with the hooded and Irish coat patterns, respectively, across all colored rat strains examined. Interestingly, all 117 albino rat strains shared the ERV insertion without any exception, which strongly suggests that the albino mutation had originally occurred in hooded rats.

Preliminary research on measuring grease in petroleum pipeline using fast neutron transmission method

International Nuclear Information System (INIS)

Liu Qingwei; Liu Shengkang; Zhang Zhiping; Ding Xiaoping

2006-01-01

The principle, experiment and conclusion on the grease stain measurement using fast neutron are reported. The experiment equipment consist of 241 Am-Be fast neutron source, ZnS detector and BH1224 multichannel spectrometer. Paraffin is used instead of real grease stain. Steel plates are used instead of pipeline. The results of the experiment indicate that there is a good linearship between the logarithm of the reciprocal of the neutron transmissivity and the paraffin thickness. The measuring accuracy of the paraffin thickness is 0.6 mm in this experiment. (authors)

Ecological Baseline, Fort Hood, Texas

Science.gov (United States)

1980-08-01

cedar eTm (Uiimus crassifolia), Texas ash (Fraxinus texansis), and Texas persimmon ( Diospyros texana). Conversely, the two predominant tree species...Ilex decidua), Mex- ican buckeye (Ungnadia spjeciosa), and Texas persimmon ( Diospyros texana). Vines included greenbrier (Smilax bona-nox) and white...Hedgehey Cactus (Echinocereus sp.) has been observed on Fort Hood. Due to the brief period of flowering for this genus , the individual species were not

Experimental study on centerline velocities of a rectangular capture hood under realistic conditions.

Science.gov (United States)

He, Xinjian; Lewis, Braxton V; Guffey, Steven E

2018-02-01

Capture hoods are an important component of a local ventilation system designed to reduce exposures to airborne contaminants. The velocity at any point along the centerline of the hood (V x ) is currently estimated using one of many predictive equations developed since the 1930s. It is unproven that those predictive equations for V x are accurate, despite the prodigious number of studies concerning them. Among other issues, almost all experimental verifications were conducted for conditions that were either unrealistically ideal without competing air currents (e.g., zero cross draft) or were not described. This study measured values of V x along the midline using Particle Image Velocimetry (PIV) at distances of 1-14 inches in front of a rectangular capture hood. The experiments were conducted in a large wind tunnel (9' × 12' × 40', H × W × L) using a heated, breathing, anthropomorphically sized manikin. Three 0 degree draft velocities (V draft = 4, 14, and 50 ft/min) were tested, all directed toward the hood face and the back of the manikin (if present). For each value of V draft , the velocity fields were measured in a factorial design with and without the manikin, and with and without a worktable underneath the hood. An ideal condition was represented by a freestanding hood at the 4 fpm draft. Nonideal conditions included the presence of a worktable or manikin, and the combination of table and manikin. Each condition was tested at the three levels of V draft . The experimental results found significant effects (p < 0.001) for V draft , the presence of the manikin, the presence of the worktable, and all combinations of those factors. The effects of the independent variables were most pronounced at distances greater than 10 in (25.4 cm) from the hood face. It is concluded that none of the previously published models accurately predicted V x under the realistic conditions tested in this study. A satisfactory model will have to include terms for V draft and the

Hooded mergansers swim in the waters of KSC

Science.gov (United States)

1999-01-01

A male and two female hooded mergansers swim in the waters of the Merritt Island National Wildlife Refuge at Kennedy Space Center. The male displays its distinctive fan-shaped, black-bordered crest. Usually found from Alaska and Canada south to Nebraska, Oregon and Tennessee, hooded mergansers winter south to Mexico and the Gulf Coast, including KSC. The open water of the refuge provides wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds. The 92,000-acre refuge is also habitat for more than 310 species of birds, 25 mammals, 117 fishes and 65 amphibians and reptiles.

Design of the GLARE tool. A grease lubrication apparatus for research and education

International Nuclear Information System (INIS)

Rawlings, B.

2012-01-01

The GLARE: Grease Lubrication Apparatus for Research and Education was designed as a fourth year thesis project with the University of Ontario Institute of Technology (UOIT). The purpose of the apparatus is to train Ontario Power Generation Nuclear (OPGN) staff to properly lubricate bearings with grease and to help detect early equipment failures. Proper re-lubrication is critical to the nuclear industry as equipment may be inaccessible for long periods of time. A secondary purpose for the tool is for UOIT research and undergraduate laboratories.This abstract provides an overview of the project and its application to the nuclear industry. (author)

The Influence of the Bed with a Semiopen Hood on Bacteria Removal in a Negative-Pressure Isolation Room

OpenAIRE

Jeng-Min Huang; Hsiang-Tai Cheng

2014-01-01

This study numerically investigates the influence of a sickbed with a semiopened hood on bacteria removal in a negative-pressure isolation room. The parameters include air change rate, lying style, the length and height of hood, flow rate allotments, and the positions of outlets. The results show that the hood has excellent effect on the removal of contaminated air, which is much better than the case without hood. The flow field of patient's face up cough is very different from face side coug...

Effect of bacterial lipase on anaerobic co-digestion of slaughterhouse wastewater and grease in batch condition and continuous fixed-bed reactor.

Science.gov (United States)

Affes, Maha; Aloui, Fathi; Hadrich, Fatma; Loukil, Slim; Sayadi, Sami

2017-10-10

This study aimed to investigate the effects of bacterial lipase on biogas production of anaerobic co-digestion of slaughterhouse wastewater (SHWW) and hydrolyzed grease (HG). A neutrophilic Staphylococcus xylosus strain exhibiting lipolytic activity was used to perform microbial hydrolysis pretreatment of poultry slaughterhouse lipid rich waste. Optimum proportion of hydrolyzed grease was evaluated by determining biochemical methane potential. A high biogas production was observed in batch containing a mixture of slaughterhouse composed of 75% SHWW and 25% hydrolyzed grease leading to a biogas yield of 0.6 L/g COD introduced. Fixed bed reactor (FBR) results confirmed that the proportion of 25% of hydrolyzed grease gives the optimum condition for the digester performance. Biogas production was significantly high until an organic loading rate (OLR) of 2 g COD/L. d. This study indicates that the use of biological pre-treatment and FBR for the co-digestion of SHWW and hydrolyzed grease is feasible and effective.

A floating bridge disrupts seaward migration and increases mortality of steelhead smolts in Hood Canal, Washington state.

Directory of Open Access Journals (Sweden)

Megan Moore

Full Text Available Habitat modifications resulting from human transportation and power-generation infrastructure (e.g., roads, dams, bridges can impede movement and alter natural migration patterns of aquatic animal populations, which may negatively affect survival and population viability. Full or partial barriers are especially problematic for migratory species whose life histories hinge on habitat connectivity.The Hood Canal Bridge, a floating structure spanning the northern outlet of Hood Canal in Puget Sound, Washington, extends 3.6 meters underwater and forms a partial barrier for steelhead migrating from Hood Canal to the Pacific Ocean. We used acoustic telemetry to monitor migration behavior and mortality of steelhead smolts passing four receiver arrays and several single receivers within the Hood Canal, Puget Sound, and Strait of Juan de Fuca. Twenty-seven mortality events were detected within the vicinity of the Hood Canal Bridge, while only one mortality was recorded on the other 325 receivers deployed throughout the study area. Migrating steelhead smolts were detected at the Hood Canal Bridge array with greater frequency, on more receivers, and for longer durations than smolts migrating past three comparably configured arrays. Longer migration times and paths are likely to result in a higher density of smolts near the bridge in relation to other sites along the migration route, possibly inducing an aggregative predator response to steelhead smolts.This study provides strong evidence of substantial migration interference and increased mortality risk associated with the Hood Canal Bridge, and may partially explain low early marine survival rates observed in Hood Canal steelhead populations. Understanding where habitat modifications indirectly increase predation pressures on threatened populations helps inform potential approaches to mitigation.

A floating bridge disrupts seaward migration and increases mortality of steelhead smolts in Hood Canal, Washington state.

Science.gov (United States)

Moore, Megan; Berejikian, Barry A; Tezak, Eugene P

2013-01-01

Habitat modifications resulting from human transportation and power-generation infrastructure (e.g., roads, dams, bridges) can impede movement and alter natural migration patterns of aquatic animal populations, which may negatively affect survival and population viability. Full or partial barriers are especially problematic for migratory species whose life histories hinge on habitat connectivity. The Hood Canal Bridge, a floating structure spanning the northern outlet of Hood Canal in Puget Sound, Washington, extends 3.6 meters underwater and forms a partial barrier for steelhead migrating from Hood Canal to the Pacific Ocean. We used acoustic telemetry to monitor migration behavior and mortality of steelhead smolts passing four receiver arrays and several single receivers within the Hood Canal, Puget Sound, and Strait of Juan de Fuca. Twenty-seven mortality events were detected within the vicinity of the Hood Canal Bridge, while only one mortality was recorded on the other 325 receivers deployed throughout the study area. Migrating steelhead smolts were detected at the Hood Canal Bridge array with greater frequency, on more receivers, and for longer durations than smolts migrating past three comparably configured arrays. Longer migration times and paths are likely to result in a higher density of smolts near the bridge in relation to other sites along the migration route, possibly inducing an aggregative predator response to steelhead smolts. This study provides strong evidence of substantial migration interference and increased mortality risk associated with the Hood Canal Bridge, and may partially explain low early marine survival rates observed in Hood Canal steelhead populations. Understanding where habitat modifications indirectly increase predation pressures on threatened populations helps inform potential approaches to mitigation.

40 CFR 761.375 - Specific requirements for surfaces coated or covered with dust, dirt, grime, grease, or another...

Science.gov (United States)

2010-07-01

... coated or covered with dust, dirt, grime, grease, or another absorbent material. 761.375 Section 761.375... coated or covered with dust, dirt, grime, grease, or another absorbent material. (a) First wash. Cover..., absorbent pad until the surface appears dry. This cleaning should remove any residual dirt, dust, grime, or...

Orthogonal design on range hood with air curtain and its effects on kitchen environment.

Science.gov (United States)

Liu, Xiaomin; Wang, Xing; Xi, Guang

2014-01-01

Conventional range hoods cannot effectively prevent the oil fumes containing cooking-induced harmful material from escaping into the kitchen Air curtains and guide plates have been used in range hoods to reduce the escape of airborne emissions and heat, thereby improving the kitchen environment and the cook's degree of comfort. In this article, numerical simulations are used to study the effects of the jet velocity of an air curtain, the jet angle of the air curtain, the width of the jet slot, the area of the guide plate, and the exhaust rate of the range hood on the perceived temperature, the perceived concentration of oil fumes, the release temperature of oil fumes, and the concentration of escaped oil fumes in a kitchen. The orthogonal experiment results show that the exhaust rate of the range hood is the main factor influencing the fumes concentration and the temperature distribution in the kitchen. For the range hood examined in the present study, the optimum values of the exhaust rate, the jet velocity of the air curtain, the jet angle of the air curtain, the width of the jet slot, and the area of the guide plate are 10.5 m(3)/min, 1.5 m/s, -5°, 4 mm, and 0.22 m(2), respectively, based on the results of the parametric study. In addition, the velocity field, temperature field, and oil fumes concentration field in the kitchen using the proposed range hood with the air curtain and guide plate are analyzed for those parameters. The study's results provide significant information needed for improving the kitchen environment.

REDESIGN OF OUTER HOOD PANEL OF ESEMKA R2 CAR TO IMPROVE PEDESTRIAN PROTECTION USING FINITE ELEMENT MODELING

Directory of Open Access Journals (Sweden)

Binyamin Binyamin

2016-12-01

Full Text Available Traffic accidents are terrible scourge that occur in many countries, specially for developing countries where transportation affairs like tangled yarn. Besides functioning as an engine compartment cover, the hood of modern compact SUV can also help to manage the impact energy of a pedestrian’s head in a vehicle-pedestrian impact. This paper presents outer hood design of Esemka R2 that has a potential to improve hood’s ability and also to absorb the impact energy of a pedestrian’s head. The developed method for the design of an outer hood configuration aims to provide a robust design and homogeneous of Head Injury Criterion (HIC for impact position at WAD 1000 and three different thicknesses (1.25 mm, 1.35 mm & 1.50 mm of outer hood panel of Esemka R2 compact SUV, taking into consideration the limited space available for deformation. The non-linear Finite Element Analysis (FEA software (Explicit Dynamics was used in this research to simulate the testing procedurs of head impact for child pedestrian. The results show that the average of comparison dimensional of outer hood panel of Esemka R2 was 4.89 mm. The minimum of deformation space meet the requirement for HIC value which required obtaining robust and homogeneous head impact performance. Outer hood thickness and materials were identified as the factors to influence the stress and HIC value of the hood. By comparing all outer hood panels, aluminium alloy as the best selected material which has the lowest value is 32.78% for the pedestrian protection.

Sexual aggression by intruders in hooded crow Corvus cornix.

Science.gov (United States)

Zduniak, Piotr; Kosicki, Jakub Z; Yosef, Reuven

The hooded crow Corvus cornix is a west Palaearctic, solitary nesting, monogamous corvid. In the breeding season, populations are characterized by a social organization wherein breeding pairs are territorial and non-breeding individuals, called floaters, live in flocks. During a study of the breeding ecology of the hooded crow, conducted in a protected flooded area, we monitored nests with video cameras. We recorded two separate incidents when intruders attacked a female at the nest. We believe that she remained in the nest in order to prevent the strangers cannibalizing the nestlings by mantling over the brood. The spatio-temporal occurrence of these attacks suggests that the observed behaviour is intraspecific sexual aggression wherein non-breeding males mounted an immobilized female.

Humboldt Open Ocean Disposal Site (HOODS) Survey Work 2014

Data.gov (United States)

U.S. Environmental Protection Agency — The Humboldt Open Ocean Disposal Site (HOODS) is a dredged material disposal site located 3 nautical miles (nm) offshore of Humboldt Bay in Northern California....

Persistence of Change: Fume Hood Campaign Lessons

Science.gov (United States)

Feder, Elah; Robinson, Jennifer; Wakefield, Sarah

2012-01-01

Purpose: Sustainability initiatives typically operate for a limited time period, but it is often unclear whether they have lasting effects. The purpose of this paper is to examine a laboratory fume hood campaign, in order to identify factors that might contribute or detract from long-term change persistence. Design/methodology/approach: The…

Reduced-scale experimental investigation on ventilation performance of a local exhaust hood in an industrial plant

DEFF Research Database (Denmark)

Huang, Yanqiu; Wang, Yi; Liu, Li

2015-01-01

stratification in the working areas of industrial plants. Investigated factors were confined airflow boundaries, flow rates of the exhaust hoods, source strengths, airflow obstacles and distances between sources and exhaust hoods. Reduced-scale experiments were conducted with a geometric scale of 1...... efficiency. Hood performance was also evaluated by thermal stratification heights in the plants. This study could help improve the capture efficiency of local ventilation systems used in industrial plants. Safe operation heights are recommended in the upper space of industrial plants based on the thermal...

Radioisotope studies on the paradox in dispersion and agglomeration of sewage greases discharged from ocean outfalls

International Nuclear Information System (INIS)

Davison, A.; Easy, J.F.; Seatonberry, B.W.

1981-04-01

Experiments have been undertaken in the ocean off Sydney, Australia to monitor the movement and the dispersion of sewage solids. These solids were labelled with a radioisotope, gold-198 prior to ocean discharge. The labelled material was followed at sea using submersible scintillation detectors. Lateral and vertical dispersion coefficients were determined. The experiments showed that under some conditions the labelled sewage grease dispersed and under others the grease agglomerated. This variation is explained in terms of non-conservative processes

42 CFR 84.135 - Half-mask facepieces, full facepieces, hoods, and helmets; fit; minimum requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Half-mask facepieces, full facepieces, hoods, and... OF RESPIRATORY PROTECTIVE DEVICES Supplied-Air Respirators § 84.135 Half-mask facepieces, full facepieces, hoods, and helmets; fit; minimum requirements. (a) Half-mask facepieces and full facepieces shall...

On the normal stress effect in grease-lubricated bearing seals

NARCIS (Netherlands)

Baart, P.; Lugt, Pieter Martin; Prakash, B.

2014-01-01

The film formation in lip seals, due to the non-Newtonian rheology of the lubricant, has been a topic of speculation. Earlier work suggests that normal stresses in grease would be favorable for the film buildup between the seal lip and shaft or bearing ring. In the current article, we evaluate this

Hood River and Pelton Ladder Evaluation Studies, 2008 Annual Report : October 2007 - September 2008.

Energy Technology Data Exchange (ETDEWEB)

Reagan, Robert E.; Olsen, Erik A. [Oregon Department of Fish and Wildlife

2009-09-28

This report summarizes the life history and production data collected in the Hood River subbasin during FY 2008. Included is a summary of jack and adult life history data collected at the Powerdale Dam trap on seventeen complete run years of winter steelhead, spring and fall chinook salmon, and coho salmon, and on fifteen complete run years of summer steelhead. Also included are summaries of (1) the hatchery winter steelhead broodstock collection program; (2) hatchery production releases in the Hood River subbasin; (3) subbasin wild summer and winter steelhead smolt production, (4) numbers of hatchery summer and winter steelhead smolts leaving the subbasin; (5) smolt migration timing past Bonneville Dam, (6) wild and hatchery steelhead smolt-to-adult survival rates; (7) wild summer and winter steelhead egg to smolt survival rates; and (8) streamflow at selected locations in the Hood River subbasin. Data will be used in part to (1) evaluate the HRPP relative to its impact on indigenous populations of resident and anadromous salmonids (see Ardren Draft), (2) evaluate the HRPP's progress towards achieving the biological fish objectives defined in the Hood River Subbasin Plan (Coccoli 2004) and the Revised Master Plan for the Hood River Production Program (HDR|FishPro, ODFW, and CTWSRO 2008), (3) refine spawner escapement objectives to more accurately reflect subbasin carrying capacity, and (4) refine estimates of subbasin smolt production capacity to more accurately reflect current and potential subbasin carrying capacity.

Anti-tuberculosis activities of the crude methanolic extract and ...

African Journals Online (AJOL)

olayemitoyin

standard drugs. The petri dishes were sealed with a carbon-dioxide permeable tape, left overnight in biosafety hood to allow diffusion of the extract, fractions. It was then incubated at 370C in a carbon- dioxide incubator for 4 weeks. The susceptibility of. M. tuberculosis isolates to the extract and the drugs was determined by ...

Brucella pinnipedialis hooded seal (Cystophora cristata) strain in the mouse model with concurrent exposure to PCB 153.

Science.gov (United States)

Nymo, Ingebjørg H; das Neves, Carlos G; Tryland, Morten; Bårdsen, Bård-Jørgen; Santos, Renato Lima; Turchetti, Andreia Pereira; Janczak, Andrew M; Djønne, Berit; Lie, Elisabeth; Berg, Vidar; Godfroid, Jacques

2014-05-01

Brucellosis, a worldwide zoonosis, is linked to reproductive problems in primary hosts. A high proportion of Brucella-positive hooded seals (Cystophora cristata) have been detected in the declined Northeast Atlantic stock. High concentrations of polychlorinated biphenyls (PCBs) have also been discovered in top predators in the Arctic, including the hooded seal, PCB 153 being most abundant. The aim of this study was to assess the pathogenicity of Brucella pinnipedialis hooded seal strain in the mouse model and to evaluate the outcome of Brucella spp. infection after exposure of mice to PCB 153. BALB/c mice were infected with B. pinnipedialis hooded seal strain or Brucella suis 1330, and half from each group was exposed to PCB 153 through the diet. B. pinnipedialis showed a reduced pathogenicity in the mouse model as compared to B. suis 1330. Exposure to PCB 153 affected neither the immunological parameters, nor the outcome of the infection. Altogether this indicates that it is unlikely that B. pinnipedialis contribute to the decline of hooded seals in the Northeast Atlantic. Copyright © 2014 Elsevier Ltd. All rights reserved.

Energy Impacts of Effective Range Hood Use for all U.S. Residential Cooking

Energy Technology Data Exchange (ETDEWEB)

Logue, Jennifer M; Singer, Brett

2014-06-01

Range hood use during residential cooking is essential to maintaining good indoor air quality. However, widespread use will impact the energy demand of the U.S. housing stock. This paper describes a modeling study to determine site energy, source energy, and consumer costs for comprehensive range hood use. To estimate the energy impacts for all 113 million homes in the U.S., we extrapolated from the simulation of a representative weighted sample of 50,000 virtual homes developed from the 2009 Residential Energy Consumption Survey database. A physics-based simulation model that considered fan energy, energy to condition additional incoming air, and the effect on home heating and cooling due to exhausting the heat from cooking was applied to each home. Hoods performing at a level common to hoods currently in U.S. homes would require 19?33 TWh [69?120 PJ] of site energy, 31?53 TWh [110-190 PJ] of source energy; and would cost consumers $1.2?2.1 billion (U.S.$2010) annually in the U.S. housing stock. The average household would spend less than $15 annually. Reducing required airflow, e.g. with designs that promote better pollutant capture has more energy saving potential, on average, than improving fan efficiency.

A male hooded merganser swims in the waters of KSC

Science.gov (United States)

1999-01-01

The distinctive fan-shaped, black-bordered crest and striped breast identify this hooded merganser, swimming in the waters of the Merritt Island National Wildlife Refuge at Kennedy Space Center. Usually found from Alaska and Canada south to Nebraska, Oregon and Tennessee, hooded mergansers winter south to Mexico and the Gulf Coast, including KSC. The open water of the refuge provides wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds. The 92,000-acre refuge is also habitat for more than 310 species of birds, 25 mammals, 117 fishes and 65 amphibians and reptiles.

A new method for infrared imaging of air currents in and around critical hazard fume hoods

International Nuclear Information System (INIS)

Mulac, W.A.; McCreary, J.R.; Schmalz, H.

1992-01-01

A real time method of measuring and recording the efficacy of vapor containment in and around critical hazard fume hoods is being developed. An infrared camera whose response is restricted to a spectral range that overlaps a strong absorption band in a non-toxic gas is used to render real-time video images of the presence and flow of the gas. The gas, nitrous oxide, is ejected in a continuous stream in and around fume hoods that are to be certified capable of containing hazardous fumes. The principle advantage is that various scenarios of air flow displacement in and outside the hood can be easily investigated; the principle limitation is the necessity of high tracer gas concentration to obtain strong visualizations. We hope that this technique can be found to be an effective and safe method to test hoods in locations that were built before present regulations were promulgated

Some Important Observations on the Populations of Hooded Vultures Necrosyrtes monachus in Urban Ghana

Directory of Open Access Journals (Sweden)

Francis Gbogbo

2016-01-01

Full Text Available Despite major declines in the population of vultures around the world, noticeable increases were reported in the populations of Hooded Vultures Necrosyrtes monachus over the past decade in Accra—an important vulture habitat in Ghana. In recent times, however, there is a growing concern that the vulture numbers are decreasing even though scientific data to support this is nonexisting. As a vital zoogeographical and conservation tool, it is important to keep an up-to-date knowledge about urban bird populations amidst rapid urbanization and associated changes. Using a combination of field data, literature review, and stakeholder consultations, it was indicative that severe decline might have indeed occurred in the populations of Hooded Vultures in Accra. Evidence suggests the killing of vultures for consumption, traditional medicine, and black magic in an undercover trade with possible transboundary connections as important underlying factor. Additional factors suspected to underlie the declines include changes in management of urban facilities and destruction of roosting and nesting trees. The implications of interspecific competition with Pied Crows Corvus albus on Hooded Vultures however remain unclear. There is an urgent need for conservation campaign and education to save the Hooded Vulture in Ghana.

Potential inhalation exposure and containment efficiency when using hoods for handling nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Tsai, Candace Su-Jung, E-mail: tsai51@purdue.edu [Purdue University, School of Health Science (United States)

2013-09-15

Inhalation exposure to airborne nanoparticles (NPs) has been reported during manual activities using typical fume hoods. This research studied potential inhalation exposure associated with the manual handling of NPs using two new nanoparticle-handling enclosures and two biological safety cabinets, and discussed the ability to contain NPs in the hoods to reduce environmental release and exposure. Airborne concentrations of 5 nm to 20 {mu}m diameter particles were measured while handling nanoalumina particles in various ventilated enclosures. Tests were conducted using two handling conditions and concentrations were measured using real-time particle counters, and particles were collected on transmission electron microscope grids to determine particle morphology and elemental composition. Airflow patterns were characterized visually using a laser-light sheet and fog. The average number concentration increase at breathing zone outside the enclosure was less than 1,400 particle/cm{sup 3} for each particle size at all tested conditions and the estimated overall mass concentration was about 83 {mu}g/m{sup 3} which was less than the dosage of typical nanoparticle inhalation exposure studies. The typical front-to-back airflow was used in the studied hoods, which could potentially induce reverse turbulence in the wake region. However, containment of NPs using studied hoods was demonstrated with excellent performance. Smoke tests showed that worker's hand motion could potentially cause nanoparticle escape. The challenge of front-to-back airflow can be partially overcome by gentle motion, low face velocity, and front exhaust to reduce nanoparticle escape.

42 CFR 84.1135 - Half-mask facepieces, full facepieces, hoods, helmets, and mouthpieces; fit; minimum requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Half-mask facepieces, full facepieces, hoods... Air-Purifying High Efficiency Respirators and Combination Gas Masks § 84.1135 Half-mask facepieces, full facepieces, hoods, helmets, and mouthpieces; fit; minimum requirements. (a) Half-mask facepieces...

Entrance and Survival of Brucella pinnipedialis Hooded Seal Strain in Human Macrophages and Epithelial Cells

Science.gov (United States)

Briquemont, Benjamin; Sørensen, Karen K.; Godfroid, Jacques

2013-01-01

Marine mammal Brucella spp. have been isolated from pinnipeds (B. pinnipedialis) and cetaceans (B. ceti) from around the world. Although the zoonotic potential of marine mammal brucellae is largely unknown, reports of human disease exist. There are few studies of the mechanisms of bacterial intracellular invasion and multiplication involving the marine mammal Brucella spp. We examined the infective capacity of two genetically different B. pinnipedialis strains (reference strain; NTCT 12890 and a hooded seal isolate; B17) by measuring the ability of the bacteria to enter and replicate in cultured phagocytes and epithelial cells. Human macrophage-like cells (THP-1), two murine macrophage cell lines (RAW264.7 and J774A.1), and a human malignant epithelial cell line (HeLa S3) were challenged with bacteria in a gentamicin protection assay. Our results show that B. pinnipedialis is internalized, but is then gradually eliminated during the next 72 – 96 hours. Confocal microscopy revealed that intracellular B. pinnipedialis hooded seal strain colocalized with lysosomal compartments at 1.5 and 24 hours after infection. Intracellular presence of B. pinnipedialis hooded seal strain was verified by transmission electron microscopy. By using a cholesterol-scavenging lipid inhibitor, entrance of B. pinnipedialis hooded seal strain in human macrophages was significantly reduced by 65.8 % (± 17.3), suggesting involvement of lipid-rafts in intracellular entry. Murine macrophages invaded by B. pinnipedialis do not release nitric oxide (NO) and intracellular bacterial presence does not induce cell death. In summary, B. pinnipedialis hooded seal strain can enter human and murine macrophages, as well as human epithelial cells. Intracellular entry of B. pinnipedialis hooded seal strain involves, but seems not to be limited to, lipid-rafts in human macrophages. Brucella pinnipedialis does not multiply or survive for prolonged periods intracellulary. PMID:24376851

Reaching for 100% participation in a utility conservation programme: the Hood River project

Energy Technology Data Exchange (ETDEWEB)

Hirst, Eric

1989-04-01

The Hood River Conservation Project (HRCP) was a major residential retrofit demonstration project. The project was intended to install as many cost-effective retrofit measures in all electrically heated homes in Hood River, OR, USA. To achieve 100% participation, HRCP offered a package of 'super' retrofit measures and paid for installation of these measures. Almost all (91%) of the eligible households participated, in stark contrast to the much lower participation levels achieved in other residential conservation programmes. Also, unlike other programmes, HRCP attracted larger fractions of traditionally hard-to-reach groups: low-income households; occupants of multifamily units; and renters. The key factors leading to this phenomenal success include: the offer of free retrofits; determination on the part of staff to enlist every eligible household; the use of community-based marketing approaches; and reliance on extensive word-of-mouth among Hood River residents. (author).

42 CFR 84.175 - Half-mask facepieces, full facepieces, hoods, helmets, and mouthpieces; fit; minimum requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Half-mask facepieces, full facepieces, hoods....175 Half-mask facepieces, full facepieces, hoods, helmets, and mouthpieces; fit; minimum requirements. (a) Half-mask facepieces and full facepieces shall be designed and constructed to fit persons with...

Effects of Atomic Oxygen and Grease on Outgassing and Adhesion of Silicone Elastomers for Space Applications

Science.gov (United States)

de Groh, Henry C.; Puleo, Bernadette J.; Steinetz, Bruce M.

An investigation of silicone elastomers for seals used in docking and habitat systems for future space exploration vehicles is being conducted at NASA. For certain missions, NASA is considering androgynous docking systems where two vehicles each having a seal would be required to: dock for a period of time, seal effectively, and then separate with minimum push-off forces for undocking. Silicone materials are generally chosen for their wide operating temperatures and low leakage rates. However silicone materials are often sticky and usually exhibit considerable adhesion when mated against metals and silicone surfaces. This paper investigates the adhesion unit pressure for a space rated silicone material (S0383-70) for either seal-on-seal (SoS) or seal-on-aluminum (SoAl) operation modes in the following conditions: as-received, after ground-based atomic-oxygen (AO) pre-treatment, after application of a thin coating of a space-qualified grease (Braycote 601EF), and after a combination of AO pre-treatment and grease coating. In order of descending adhesion reduction, the AO treatment reduced seal adhesion the most, followed by the AO plus grease pre-treatment, followed by the grease treatment. The effects of various treatments on silicone (S0383-70 and ELA-SA-401) outgassing properties were also investigated. The leading adhesion AO pre-treatment reduction led to a slight decrease in outgassing for the S0383-70 material and virtually no change in ELA-SA-401 outgassing.

Simultaneous removal of oil and grease, and heavy metals from artificial bilge water using electro-coagulation/flotation.

Science.gov (United States)

Rincón, Guillermo J; La Motta, Enrique J

2014-11-01

US and international regulations pertaining to the control of bilge water discharges from ships have concentrated their attention to the levels of oil and grease rather than to the heavy metal concentrations. The consensus is that any discharge of bilge water (and oily water emulsion within 12 nautical miles from the nearest land cannot exceed 15 parts per million (ppm). Since there is no specific regulation for metal pollutants under the bilge water section, reference standards regulating heavy metal concentrations are taken from the ambient water quality criteria to protect aquatic life. The research herein presented discusses electro-coagulation (EC) as a method to treat bilge water, with a focus on oily emulsions and heavy metals (copper, nickel and zinc) removal efficiency. Experiments were run using a continuous flow reactor, manufactured by Ecolotron, Inc., and a synthetic emulsion as artificial bilge water. The synthetic emulsion contained 5000 mg/L of oil and grease, 5 mg/L of copper, 1.5 mg/L of nickel, and 2.5 mg/l of zinc. The experimental results demonstrate that EC is very efficient in removing oil and grease. For oil and grease removal, the best treatment and cost efficiency was obtained when using a combination of carbon steel and aluminum electrodes, at a detention time less than one minute, a flow rate of 1 L/min and 0.6 A/cm(2) of current density. The final effluent oil and grease concentration, before filtration, was always less than 10 mg/L. For heavy metal removal, the combination of aluminum and carbon steel electrodes, flow rate of 1 L/min, effluent recycling, and 7.5 amps produced 99% zinc removal efficiency. Copper and nickel are harder to remove, and a removal efficiency of 70% was achieved. Copyright © 2014 Elsevier Ltd. All rights reserved.

A female hooded merganser swims in the waters of KSC

Science.gov (United States)

1999-01-01

A female hooded merganser swims solo in the waters of the Merritt Island National Wildlife Refuge at Kennedy Space Center. The male is distinguished by a fan-shaped, black-bordered crest and striped breast. Usually found from Alaska and Canada south to Nebraska, Oregon and Tennessee, hooded mergansers winter south to Mexico and the Gulf Coast, including KSC. The open water of the refuge provides wintering areas for 23 species of migratory waterfowl, as well as a year-round home for great blue herons, great egrets, wood storks, cormorants, brown pelicans and other species of marsh and shore birds. The 92,000-acre refuge is also habitat for more than 310 species of birds, 25 mammals, 117 fishes and 65 amphibians and reptiles.

Don Quixote, Machiavelli, and Robin Hood: public health practice, past and present.

Science.gov (United States)

Mullan, F

2000-05-01

Since the mid-19th century, when the first formal health departments were established in the United States, commissioners, directors, and secretaries of public health have functioned as senior members of the staffs of public executives, mayors, governors, and presidents. They have provided important political, managerial, and scientific leadership to agencies of government that have played increasingly important roles in national life, from the sanitary revolution of the 19th century to the prevention of HIV/AIDS and the control of tobacco use today. Although public health officials come from a variety of backgrounds and oversee agencies of varied size and composition, there are philosophical themes that describe and define the commonality of their work. These themes are captured metaphorically by 3 celebrated figures: Don Quixote, Machiavelli, and Robin Hood. By turns, the public health official functions as a determined idealist (Don Quixote), a cunning political strategist (Machiavelli), and an agent who redistributes resources from the wealthier sectors of society to the less well off (Robin Hood.) All 3 personae are important, but, it is argued, Robin Hood is the most endangered.

Contrast fluoroscopic evaluation of gastrointestinal transit times with and without the use of falconry hoods in red-tailed hawks (Buteo jamaicensis).

Science.gov (United States)

Doss, Grayson A; Williams, Jackie M; Mans, Christoph

2017-11-01

OBJECTIVE To evaluate gastrointestinal transit times in red-tailed hawks (Buteo jamaicensis) by use of contrast fluoroscopic imaging and investigate the effect of falconry hooding in these hawks on gastrointestinal transit time. DESIGN Prospective, randomized, blinded, complete crossover study. ANIMALS 9 healthy red-tailed hawks. PROCEDURES Hawks were gavage-fed a 30% weight-by-volume barium suspension (25 mL/kg [11.3 mL/lb]) into the crop. Fluoroscopic images were obtained at multiple time points after barium administration. Time to filling and emptying of various gastrointestinal tract organs and overall transit time were measured. The effect of hooding (hooded vs nonhooded) on these variables was assessed in a randomized complete crossover design. RESULTS In nonhooded birds, overall gastrointestinal transit time ranged from 30 to 180 minutes (mean ± SD, 100 ± 52 min). Time to complete crop emptying ranged from 30 to 180 minutes (83 ± 49 min). Contrast medium was present in the ventriculus in all birds within 5 minutes of administration and in the small intestines within 5 to 15 minutes (median, 5 min). Hooding of red-tailed hawks resulted in a significant delay of complete crop emptying (no hood, 83 ± 49 minutes; hood, 133 ± 48 minutes), but no significant effects of hooding were found on other measured variables. CONCLUSIONS AND CLINICAL RELEVANCE These results indicated that overall gastrointestinal transit times are faster in red-tailed hawks than has been reported for psittacines and that the use of a falconry hood in red-tailed hawks may result in delayed crop emptying. Hooding did not exert significant effects on overall gastrointestinal transit time in this raptorial species.

A support approach for the conceptual design of energy-efficient cooker hoods

International Nuclear Information System (INIS)

Cicconi, Paolo; Landi, Daniele; Germani, Michele; Russo, Anna Costanza

2017-01-01

Highlights: •An eco-innovation approach to support the design of household appliances. •The research is focused on the energy labelling for kitchen hoods. •A software platform provides tools to configure and optimize new solutions. •A tool can calculate the energy efficiency indexes of a product configuration. -- Abstract: In Europe, kitchen hoods currently come with an energy label showing their energy efficiency class and other information regarding the energy consumption and noise level, as established by the European Energy Labelling Directive. Because of recent regulations, designs of cooker hoods must consider new issues, such as the evaluation of the energy efficiency, analysis of the energy consumption, and product lifecycle impact. Therefore, the development of eco-driven products requires Ecodesign tools to support eco-innovation and related sustainability improvements. The scope of the proposed research is to define a method and an agile and affordable platform tool that can support designers in the early estimation of product energy performance, including the calculation of energy efficiency indexes. The approach also considers the use of genetic algorithm methods to optimize the product configuration in terms of energy efficiency. The research context concerns large and small productions of kitchen hoods. The paper describes the methodological approach within the developed tool. The results show a good correlation between real efficiency values and calculated ones. A validation activity has been described, and a test case shows how to apply the proposed approach for the design of a new efficient product with an A-class Energy Efficiency Index.

Freshwater and Saline Loads of Dissolved Inorganic Nitrogen to Hood Canal and Lynch Cove, Western Washington

Science.gov (United States)

Paulson, Anthony J.; Konrad, Christopher P.; Frans, Lonna M.; Noble, Marlene; Kendall, Carol; Josberger, Edward G.; Huffman, Raegan L.; Olsen, Theresa D.

2006-01-01

Hood Canal is a long (110 kilometers), deep (175 meters) and narrow (2 to 4 kilometers wide) fjord of Puget Sound in western Washington. The stratification of a less dense, fresh upper layer of the water column causes the cold, saltier lower layer of the water column to be isolated from the atmosphere in the late summer and autumn, which limits reaeration of the lower layer. In the upper layer of Hood Canal, the production of organic matter that settles and consumes dissolved oxygen in the lower layer appears to be limited by the load of dissolved inorganic nitrogen (DIN): nitrate, nitrite, and ammonia. Freshwater and saline loads of DIN to Hood Canal were estimated from available historical data. The freshwater load of DIN to the upper layer of Hood Canal, which could be taken up by phytoplankton, came mostly from surface and ground water from subbasins, which accounts for 92 percent of total load of DIN to the upper layer of Hood Canal. Although DIN in rain falling on land surfaces amounts to about one-half of the DIN entering Hood Canal from subbasins, rain falling directly on the surface of marine waters contributed only 4 percent of the load to the upper layer. Point-source discharges and subsurface flow from shallow shoreline septic systems contributed less than 4 percent of the DIN load to the upper layer. DIN in saline water flowing over the sill into Hood Canal from Admiralty Inlet was at least 17 times the total load to the upper layer of Hood Canal. In September and October 2004, field data were collected to estimate DIN loads to Lynch Cove - the most inland marine waters of Hood Canal that routinely contain low dissolved-oxygen waters. Based on measured streamflow and DIN concentrations, surface discharge was estimated to have contributed about one-fourth of DIN loads to the upper layer of Lynch Cove. Ground-water flow from subbasins was estimated to have contributed about one-half of total DIN loads to the upper layer. In autumn 2004, the relative

Sodium-glucose cotransporter 2 inhibition and health benefits: The Robin Hood effect.

Science.gov (United States)

Kalra, Sanjay; Jain, Arpit; Ved, Jignesh; Unnikrishnan, A G

2016-01-01

This review discusses two distinct, yet related, mechanisms of sodium-glucose cotransporter 2 (SGLT2) inhibition: Calorie restriction mimicry (CRM) and pro-ketogenic effect, which may explain their cardiovascular benefits. We term these adaptive CRM and pro-ketogenic effects of SGLT2 inhibition, the Robin Hood hypothesis. In English history, Robin Hood was a "good person," who stole from the rich and helped the poor. He supported redistribution of resources as he deemed fit for the common good. In a similar fashion, SGLT2 inhibition provides respite to the overloaded glucose metabolism while utilizing lipid stores for energy production.

Sodium-glucose cotransporter 2 inhibition and health benefits: The Robin Hood effect

Directory of Open Access Journals (Sweden)

Sanjay Kalra

2016-01-01

Full Text Available This review discusses two distinct, yet related, mechanisms of sodium-glucose cotransporter 2 (SGLT2 inhibition: Calorie restriction mimicry (CRM and pro-ketogenic effect, which may explain their cardiovascular benefits. We term these adaptive CRM and pro-ketogenic effects of SGLT2 inhibition, the Robin Hood hypothesis. In English history, Robin Hood was a "good person," who stole from the rich and helped the poor. He supported redistribution of resources as he deemed fit for the common good. In a similar fashion, SGLT2 inhibition provides respite to the overloaded glucose metabolism while utilizing lipid stores for energy production.

On a new method to determine the yield stress in lubricating grease

NARCIS (Netherlands)

Cyriac, F.; Lugt, Pieter Martin; Bosman, Rob

2015-01-01

An experimental study using both a controlled stress and a controlled strain rheometer has been undertaken to characterize lubricating grease in shear, creep, stress relaxation, and oscillatory flow, with a main focus on determining the yield stress. The yield stress was examined using a cone–plate

9 CFR 316.15 - Marking outside containers of inedible grease, etc.

Science.gov (United States)

2010-01-01

... grease, etc. 316.15 Section 316.15 Animals and Animal Products FOOD SAFETY AND INSPECTION SERVICE... letters not less than 2 inches high, while on tank cars and tank trucks the letters shall be not less than 4 inches high. (b) Inspected rendered animal fat which is intended not to be used for human food may...

Wastewater transformations and fertilizer value when co-digesting differing ratios of swine manure and used cooking grease in low-cost digesters

Energy Technology Data Exchange (ETDEWEB)

Lansing, Stephanie [Department of Environmental Science and Technology, University of Maryland, 1445 Animal Sci./Ag. Eng. Bldg., College Park, MD 20742-2315 (United States); Martin, Jay F. [Department of Food, Agricultural, and Biological Engineering, The Ohio State University, 590 Woody Hayes Drive, Columbus, OH 43210-1057 (United States); Botero, Raul Botero; Nogueira da Silva, Tatiana; Dias da Silva, Ederson [EARTH University, Apartado Postal 4442 - 1000, San Jose (Costa Rica)

2010-12-15

A nine-month co-digestion investigation was conducted in Costa Rica to optimize animal wastewater treatment, renewable energy production, and fertilizer creation using 12 Taiwanese-model, plug-flow digesters (250 L each) constructed of tubular polyethylene and PVC piping, operating without mechanical or heating components. The experiment tested three replications of four treatment groups: the control (T0), which contained only swine manure, and T2.5, T5, and T10, which contained 2.5%, 5%, and 10% used cooking grease (by volume) combined with swine manure. T2.5 had the greatest methane production (45 L d{sup -1}), a 124% increase from the control. No adverse effects were observed from co-digesting 2.5% grease in terms of organic matter removal, pathogen reduction, grease removal, and pH. Chemical oxygen demand (COD) was reduced 94.7% to 1.96 g L{sup -1}, fecal coliforms and Escherichia coli were reduced 99.2 and 97.1%, respectively, and grease removal was 99.9%. The average effluent pH (7.05) and alkalinity in T2.5 was within the optimal range for methanogens and increased significantly during the nine-month experiment, likely due to adaptation of the methanogenic organisms to the influent grease concentrations. Total nitrogen concentration decreased 34.0%, and NH{sub 4}-N increased 97.1% during digestion in T2.5, with no significant differences between T2.5 and T0. There was less phosphorus reduction with co-digestion, with 181 mg g{sup -1} of total phosphorus (TP) in T2.5 and only 90.6 mg g{sup -1} of TP in T0, resulting in lower N:P ratios in the grease treatment groups due to the greater concentration of phosphorus in the effluent. (author)

The efficacy of the crude root bark extracts of Erythrina abyssinica on ...

African Journals Online (AJOL)

Administrator

tests for the extracts and the three strains of. Mycobacterium were done in triplicate. The Petri dishes were then left in the hood overnight, to allow diffusion of the extracts and drug and then sealed with a carbon dioxide-permeable tape. These were then incubated at 37°C in a carbon dioxide incubator for up to four weeks.

The decline of an urban Hooded Vulture Necrosyrtes monachus ...

African Journals Online (AJOL)

Likely causes are (1) exponential urbanisation resulting in loss of feeding sites and reduced food availability, (2) increased poisoning of feral dogs with strychnine sulphate due to an upsurge of rabies and (3) increased disappearance of suitable trees for nesting and roosting. Keywords: cutting of trees, Hooded Vulture, ...

Dynamics of participation and supply of services in the Hood River Conservation Project

Energy Technology Data Exchange (ETDEWEB)

Hirst, E.; Goeltz, R.

1986-07-01

The Hood River Conservation Project (HRCP) is a major residential retrofit demonstration project. HRCP is funded by the Bonneville Power Administration (BPA) and run by Pacific Power and Light Company. The project was conducted in the community of Hood River, Oregon, will cost $21 million, and will last for three years (mid-1983 through 1986). Installation of applicable retrofit measures was completed by the end of 1985; data collection, analysis, and report writing will continue through 1986. This report documents the extent to which households participated in HRCP. Differences between participants and eligible nonparticipants are examined. Similarly, differences among participants as a function of when they signed up for HRCP are analyzed. The report also examines the dynamics of program services (i.e., times between audit requests and audit, and between audit and installation of measures). These analyses are based on data from the roughly 3500 Hood River homes eligible for HRCP, 3189 of which received free home energy audits and 2988 of which received HRCP-financed retrofit measures.

Preliminary experimental research to detect grease stain of petroleum pipeline by sup 1 sup 3 sup 7 Cs gamma-ray transmission method

CERN Document Server

Wang Shi Heng

2002-01-01

The experimental study on the detection of grease stain for petroleum pipeline in Karamay oil-field of Xinjiang is carried out by gamma-ray transmission method. Experimental provision consists of sup 1 sup 3 sup 7 Cs gamma radiator and NaI(Tl) scintillation detector. The response of grease stain thickness of petroleum pipeline in Karamay oil-field is ln(N sub 0 /N)=0.00548 d-0.0046, and the response of paraffin thickness is ln(N sub 0 /N)=0.00522d-0.0126. The result of experiment indicates that the response of grease stain thickness is more sensitive than the response of paraffin thickness

Estimation of modes frictions and greasing in bearing axial hanging of locomotives

Directory of Open Access Journals (Sweden)

V.N. Аstаkhоv

2012-04-01

Full Text Available Dependence is considered between the size of relative diametral gap and descriptions of work of the motor-axial bearing on the different rates of movement of diesel engine: by the type of the mode of greasing, thickness lubricating layer, by the coefficient of friction and intensity of wear.

77 FR 12514 - Drawbridge Operation Regulation; Hood Canal, WA

Science.gov (United States)

2012-03-01

... operating regulation for the Hood Canal floating drawbridge near Port Gamble. This modification would relieve heavy rush hour road traffic on State Routes 3 and 104, by allowing the draws of the bridge to not.... FOR FURTHER INFORMATION CONTACT: If you have questions on this rule, call or email the Bridge...

Transfer hood for handling fuel assemblies in nuclear reactors and especially fast reactors

International Nuclear Information System (INIS)

Aubert, M.; Merland, D.; Renaux, C.

1975-01-01

A description is given of a hood for transferring fuel assemblies between two or more separate guide ramps inclined to the vertical at the same angle of slope and extending respectively through a first passage into the reactor vessel and through a second passage into a fuel-assembly storage chamber. The hood comprises at least one shielded duct joined to a flanged rotating portion which is so arranged that the open lower end of the shielded duct is positioned in the line of extension of one guide ramp and then the other as a result of displacement of the rotating portion

Hood River Monitoring and Evaluation Project, Annual Report 2002-2003.

Energy Technology Data Exchange (ETDEWEB)

Vaivoda, Alexis

2004-02-01

The Hood River Production Program Monitoring and Evaluation Project is co-managed by the Confederated Tribes of Warm Springs (CTWSRO) and the Oregon Department of Fish and Wildlife. The program is divided up to share responsibilities, provide efficiency, and avoid duplication. From October 2002 to September 2003 (FY 03) project strategies were implemented to monitor, protect, and restore anadromous fish and fish habitat in the Hood River subbasin. A description of the progress during FY 03 is reported here. Additionally an independent review of the entire program was completed in 2003. The purpose of the review was to determine if project goals and actions were achieved, look at critical uncertainties for present and future actions, determine cost effectiveness, and choose remedies that would increase program success. There were some immediate changes to the implementation of the project, but the bulk of the recommendations will be realized in coming years.

Renewable Energy Opportunities at Fort Hood, Texas

Energy Technology Data Exchange (ETDEWEB)

Chvala, William D.; Warwick, William M.; Dixon, Douglas R.; Solana, Amy E.; Weimar, Mark R.; States, Jennifer C.; Reilly, Raymond W.

2008-06-30

The document provides an overview of renewable resource potential at Fort Hood based primarily upon analysis of secondary data sources supplemented with limited on-site evaluations. The effort was funded by the U.S. Army Installation Management Command (IMCOM) as follow-on to the 2005 DoD Renewables Assessment. This effort focuses on grid-connected generation of electricity from renewable energy sources and also ground source heat pumps for heating and cooling buildings, as directed by IMCOM.

Contamination Status of Seven Elements in Hooded Cranes Wintering in South-West Kyushu, Japan: Comparison with Red-Crowned Cranes in Hokkaido, Japan.

Science.gov (United States)

Teraoka, Hiroki; Miyagi, Hasumi; Haraguchi, Yuko; Takase, Kozo; Kitazawa, Takio; Noda, Jun

2018-05-31

The hooded crane is designated as an endangered species. The cranes breed primarily in wetlands in southeast Russia and China in summer. Most of the hooded crane population winters in the Izumi plain in Japan. It is difficult to know the contamination status of their habitat because of their vast breeding area. We determined the levels of Cd, Pb, As, (total) Hg, Se, Zn, and Cu in the liver, kidney, and muscle of hooded cranes that were found dead in Izumi in the periods 2003-2006 and 2014-2015 compared with the levels in red-crowned cranes in Hokkaido, Japan, as the only cranes in which these elements had been studied extensively. There were no notable differences between levels of the seven elements in the two periods. Overall, tissue levels of the elements examined in hooded cranes were comparable to those in red-crowned cranes except for Hg and Se. Tissue levels of Hg and Se were clearly lower in hooded cranes than in red-crowned cranes that were found dead from 2000. One lead poisoning case was confirmed. The results suggest that Hooded cranes wintering in Izumi are not extensively contaminated with the seven elements examined.

First glimpse of the functional benefits of clitoral hood piercings.

Science.gov (United States)

Millner, Vaughn S; Eichold, Bernard H; Sharpe, Thomasina H; Lynn, Sherwood C

2005-09-01

In this exploratory study, we identify a positive relationship between vertical clitoral hood piercing and desire, frequency of intercourse and arousal. There were no dramatic differences in orgasmic functioning. Clinicians can play key roles in educating patients about potential outcomes and risks of genital piercing.

Effect of bacterial lipase on anaerobic co-digestion of slaughterhouse wastewater and grease in batch condition and continuous fixed-bed reactor

OpenAIRE

Affes, Maha; Aloui, Fathi; Hadrich, Fatma; Loukil, Slim; Sayadi, Sami

2017-01-01

Background This study aimed to investigate the effects of bacterial lipase on biogas production of anaerobic co-digestion of slaughterhouse wastewater (SHWW) and hydrolyzed grease (HG). A neutrophilic Staphylococcus xylosus strain exhibiting lipolytic activity was used to perform microbial hydrolysis pretreatment of poultry slaughterhouse lipid rich waste. Results Optimum proportion of hydrolyzed grease was evaluated by determining biochemical methane potential. A high biogas production was o...

Digital data for preliminary geologic map of the Mount Hood 30- by 60-minute quadrangle, northern Cascade Range, Oregon

Science.gov (United States)

Lina Ma,; Sherrod, David R.; Scott, William E.

2014-01-01

The Mount Hood 30- by 60-minute quadrangle covers the axis and east flank of the Cascade Range in northern Oregon. Its namesake, Mount Hood volcano, dominates the view in the northwest quarter of the quadrangle, but the entire area is underlain by Oligocene and younger volcanic and volcaniclastic rocks of the Cascade Range. Since the time of the Columbia River Basalt Group about 15 million years (m.y.) ago, the locus and composition of Cascade Range volcanism have shifted sporadically across the map area. Andesitic eruptions were predominant in the western part from about 14 to 10 m.y. ago (Salmon and Sandy Rivers area), producing the Rhododendron Formation and overlying lava flows. From about 8 to 6.5 m.y. ago, lithic pyroclastic debris of the Dalles Formation was shed by chiefly andesitic volcanoes in the north-central part of the map area (Hood River valley escarpment). Andesitic to dacitic volcanism was again predominant about 5 to 3 m.y. ago, with known eruptive centers located from Lookout Mountain westward to Lolo Pass, probably including the area now occupied by Mount Hood. A major episode of mafic volcanism-basalt and basaltic andesite-began about 3-4 m.y. ago and lasted until about 2 m.y. ago. Volcanism since about 2 m.y. ago has been concentrated along the axis of the High Cascades. North and south of Mount Hood these youngest rocks are predominantly basaltic andesite lava flows; whereas at Mount Hood itself, andesite is predominant, forming pyroclastic and debris-flow deposits and lava flows.

Análise de convergência espacial dos repasses da Lei Robin Hood Spatial convergence analysis of tax transfers from the Robin Hood Act

Directory of Open Access Journals (Sweden)

Noé Gonçalves Maranduba Júnior

2009-12-01

Full Text Available Alega-se que a Lei Robin Hood tem permitido uma melhor distribuição dos valores do ICMS devidos aos municípios do estado de Minas Gerais. O objetivo deste artigo é investigar se essa lei, entre os anos de 2001 e 2005, realmente foi eficaz, isto é, se, em termos relativos, municípios pobres receberam mais dessas transferências do que os municípios ricos. Para fazer isso metodologicamente, implementa-se uma análise exploratória de dados espaciais e uma análise de convergência, para verificar se as disparidades nos repasses diminuíram com o passar do tempo. Os resultados mostraram que os efeitos espaciais importaram nas análises e que não houve um efeito redistributivo dos repasses, considerando-se que o coeficiente indicador de convergência não foi significativo.One alleges that the Robin Hood Act has allowed one better distribution of the values of ICMS to municipalities of the state of Minas Gerais. The paper is aimed at verifying if the Robin Hood Act has actually revealed a redistributive effect in tax transfers to municipalities in the state over the period 2001-2005, that is, if, in relative terms, poor municipalities have received more these transfers than rich ones. In doing methodologically so, an exploratory spatial data analysis and a convergence analysis are implemented to verify if the disparities of tax redistribution have diminished over the time. The findings showed that the spatial effects were important in the analysis as well as there was no redistributive effect in the period because the convergence coefficient was not significant.

Mass transfer inside a flux hood for the sampling of gaseous emissions from liquid surfaces - Experimental assessment and emission rate rescaling

Science.gov (United States)

Prata, Ademir A.; Lucernoni, Federico; Santos, Jane M.; Capelli, Laura; Sironi, Selena; Le-Minh, Nhat; Stuetz, Richard M.

2018-04-01

This study assesses the mass transfer of compounds inside the US EPA flux hood, one of the enclosure devices most commonly employed for the direct measurement of atmospheric emissions from liquid surfaces in wastewater treatment plants (WWTPs). Experiments comprised the evaporation of water and the volatilisation of a range of volatile organic compounds (VOCs). Special attention was given to the evaluation of the mass transfer coefficients in the microenvironment created by the flux hood and the effects of concentration build up in the hood's headspace. The VOCs emission rates and the water evaporation rates generally increased with the sweep air flow rate, as did the mass transfer coefficients for all compounds. The emission of compounds whose volatilisation is significantly influenced by the gas phase was greatly affected by concentration build up, whereas this effect was not significant for liquid phase-controlled compounds. The gas-film mass transfer coefficient (kG) estimated inside the US EPA flux hood was of the same order as the respective kG reported in the literature for wind tunnel-type devices, but the emission rates measured by the flux hood can be expected to be lower, due to the concentration build-up. Compared against an emission model for the passive surfaces in WWTPs, the mass transfer of acetic acid (representing a gas phase-dominated compound) inside the US EPA flux hood was equivalent to conditions of wind speeds at 10 m height (U10) of 0.27, 0.51 and 0.99 m s-1, respectively, for sweep air flow rates of 2, 5 and 10 L min-1. On the other hand, for higher wind speeds, the emission rates of gas phase-controlled compounds obtained with the flux hood can be considerably underestimated: for instance, at U10 = 5 m s-1, the emission rates of acetic acid inside the flux hood would be approximately 23, 12 and 6 times lower than the emission rates in the field, for sweep air flow rates of 2, 5 and 10 L min-1, respectively. A procedure is presented in

76 FR 40322 - Mt. Hood Meadows Ski Resort Parking Improvements

Science.gov (United States)

2011-07-08

... fleet. Also, the location of the current maintenance shop impedes traffic flow and removes potential... new Sunrise Vehicle Maintenance Shop on the north side of the Sunrise parking lot. DATES: Comments... increasing parking capacity and improving traffic flow in at Mt. Hood Meadows Ski Resort. Parking capacity...

Food Grade Grease Berbahan Baku Minyak Sawit Crude Palm Oil (Cpo Off Grade Dengan Variasi Konsentrasi Thickening

Directory of Open Access Journals (Sweden)

Martanto Totok

2017-03-01

Full Text Available Food grade grease (FGG is a kind of lubricant made from vegetable oil. Food Grease isconsidered safe for healthy and it does not pollute the environment so that it can be veryimportant for particular industries such as pharmaceutical, animal feeding, cosmetic, andespecially food industry. This study is aiming at obtaining optimum basic formulation ofthickening agent (LiOH that can produce qualified food grade grease. It is a kind of factorialexperimental study by using complete random sampling. Based on Fisher test, the treatmentshows a different result significantly. Then, it is continued by conducting Duncan’s MultipleRange Test (DMRT. 2% of activated charcoal is the best treatment because it results FFAscore, lower water content, and the bright yellow color that is shown by the score of 5.48%,0.0498 %, and 3 % that successively obtained. The treatment on thickening agent (LiOH(P1 and the revious one (L1 are the best treatment which produce qualified food gradegrease, corrosion resistance value 12.0, dropping point 130C, lubricating texture value 1,pH value 9.45, water content 0.19%, and ash content value 0.76%.

Feeding habits of harp and hooded seals in Greenland waters

Directory of Open Access Journals (Sweden)

Finn O Kapel

2000-05-01

Full Text Available Results of stomach contents analyses of harp and hooded seals collected in West Greenland waters in the period 1986-1993 are reviewed, and compared with published data and circumstantial information from local hunters.  The diet of harp seals in this region is variable but consists mainly of pelagic crustaceans (Thysanoessa spp. and Parathemisto libellula and small fish species like capelin (Mallotus villosus, sandeel (Ammodytes spp., polar cod (Boreogadus saida and Arctic cod (Arctogadus glacialis. Species of importance for commercial fisheries in Greenland, such as Northern prawn (Pandalus borealis, Atlantic cod (Gadus morhua, and Greenland halibut (Reinhardtius hippoglossoides play a minor role in the diet of harp seals in this area. Variation in the diet of hooded seals is less well documented, but in addition to the species also taken by harp seals, larger demersal fishes like Greenland halibut, redfish (Sebastes spp., cod, and wolffish (Anarhichas minor are apparently important prey items.

Particle release and control of worker exposure during laboratory-scale synthesis, handling and simulated spills of manufactured nanomaterials in fume hoods

Science.gov (United States)

Fonseca, Ana S.; Kuijpers, Eelco; Kling, Kirsten I.; Levin, Marcus; Koivisto, Antti J.; Nielsen, Signe H.; Fransman, W.; Fedutik, Yijri; Jensen, Keld A.; Koponen, Ismo K.

2018-02-01

Fume hoods are one of the most common types of equipment applied to reduce the potential of particle exposure in laboratory environments. A number of previous studies have shown particle release during work with nanomaterials under fume hoods. Here, we assessed laboratory workers' inhalation exposure during synthesis and handling of CuO, TiO2 and ZnO in a fume hood. In addition, we tested the capacity of a fume hood to prevent particle release to laboratory air during simulated spillage of different powders (silica fume, zirconia TZ-3Y and TiO2). Airborne particle concentrations were measured in near field, far field, and in the breathing zone of the worker. Handling CuO nanoparticles increased the concentration of small particles (control during synthesis and handling of nanomaterials. An appropriate fume hood with adequate sash height and face velocity prevents 98.3% of particles release into the surrounding environment. Care should still be made to consider spills and high cleanliness to prevent exposure via resuspension and inadvertent exposure by secondary routes.

Experimental Evaluation of Installed Cooking Exhaust Fan Performance

Energy Technology Data Exchange (ETDEWEB)

Singer, Brett C.; Delp, William W.; Apte, Michael G.

2010-11-01

The installed performance of cooking exhaust fans was evaluated through residential field experiments conducted on a sample of 15 devices varying in design and other characteristics. The sample included two rear downdraft systems, two under-cabinet microwave over range (MOR) units, three different installations of an under-cabinet model with grease screens across the bottom and no capture hood, two devices with grease screens covering the bottom of a large capture hood (one under-cabinet, one wall-mount chimney), four under-cabinet open hoods, and two open hoods with chimney mounts over islands. Performance assessment included measurement of airflow and sound levels across fan settings and experiments to quantify the contemporaneous capture efficiency for the exhaust generated by natural gas cooking burners.Capture efficiency is defined as the fraction of generated pollutants that are removed through the exhaust and thus not available for inhalation of household occupants. Capture efficiency (CE) was assessed for various configurations of burner use (e.g., single front, single back, combination of one front and one back, oven) and fan speed setting. Measured airflow rates were substantially lower than the levels noted in product literature for many of the units. This shortfall was observed for several units costing in excess of $1000. Capture efficiency varied widely (from<5percent to roughly 100percent) across devices and across conditions for some devices. As expected, higher capture efficiencies were achieved with higher fan settings and the associated higher air flow rates. In most cases, capture efficiencies were substantially higher for rear burners than for front burners. The best and most consistent performance was observed for open hoods that covered all cooktop burners and operated at higher airflow rates. The lowest capture efficiencies were measured when a front burner was used with a rear backdraft system or with lowest fan setting for above the range

Characterisation of FOGs in grease trap waste from the processing of chickens in Thailand.

Science.gov (United States)

Nitayapat, Nuttakan; Chitprasert, Pakamon

2014-06-01

Industrial firms that kill and process chickens generate wastewater that contains fat, oil, and grease (FOG). The FOGs are located in the fatty waste that is collected by floatation in grease traps. Chemical and physical characterisation of FOGs would provide useful information that would help in the development of methods designed to decrease the extent of pollution caused by disposal of the waste and to utilise commercially some of its lipid constituents. Employing these methods would enhance the profitability and competitive potential of these commercial organisations. Samples of grease trap waste from 14 firms in central Thailand have been examined. Due to the very different schemes of waste management employed by these firms, the physical appearance of their fatty wastes showed considerable variation. The chemical and physical properties of the FOGs present in these wastes showed considerable variation also. Large amounts of free fatty acids (10-70% as oleic acid) were detected in most of the 14 wastes and palmitic, cis-9-oleic, cis,cis-9,12-linoleic, stearic, and palmitoleic acids were the predominant species of free and esterified acids. Most of the FOGs were solid at temperatures below 40 °C. Many of them contained traces of heavy metals (Cu and Pb) and some contained traces of the pesticides dimethoate and cypermethrin. The content of these potentially hazardous substances would have to be considered very carefully before discarding the fatty wastes and during the development of methods designed to isolate their potentially profitable lipid constituents. Copyright © 2013 Elsevier Ltd. All rights reserved.

Black on Black Crime: Hollywood's Construction of the Hood.

Science.gov (United States)

Pierson, Eric

Most of what the world envisions of the period of westward expansion in America has been crafted through Hollywood cinema. The myths of the West are so ingrained in America's culture that they have taken on a truth all their own. In a series of recent films, which began with the release of "Boyz N the Hood," Hollywood is at it again, presenting…

ATU/Fort Hood Solar Total Energy Military Large-Scale Experiment (LSE-1): system design and support activities. Final report, November 23, 1976-November 30, 1977

Energy Technology Data Exchange (ETDEWEB)

1977-01-01

The ATU/Fort Hood Solar Total Energy System will include a concentrating solar collector field of several acres. During periods of direct insolation, a heat-transfer fluid will be circulated through the collector field and thus heated to 500 to 600/sup 0/F. Some of the fluid will be circulated through a steam generator to drive a turbine-generator set; additional fluid will be stored in insulated tanks for use when solar energy is not available. The electrical output will satisfy a portion of the electrical load at Fort Hood's 87,000 Troop Housing Complex. Heat extracted from the turbine exhaust in the form of hot water will be used for space heating, absorption air conditioning, and domestic water heating at the 87,000 Complex. Storage tanks for the hot water are also included. The systems analysis and program support activities include studies of solar availability and energy requirements at Fort Hood, investigation of interfacing LSE-1 with existing energy systems at the 87,000 Complex, and preliminary studies of environmental, health, and safety considerations. An extensive survey of available concentrating solar collectors and modifications to a computerized system simulation model for LSE-1 use are also reported. Important program support activities are military liaison and information dissemination. The engineering test program reported involved completion of the Solar Engineering Test Module (SETM) and extensive performance testing of a single module of the linear-focusing collector.

Sand or grease? Corruption-institutional trust nexus in post-Soviet countries

OpenAIRE

Nazim Habibov; Elvin Afandi; Alex Cheung

2017-01-01

This paper empirically tests several hypotheses about the nexus of corruption-institutional trust in Post-Soviet transitional countries of the former Soviet Union and Mongolia. We use two different indices of institutional trust to check the robustness of our analysis and estimate OLS and instrumental variable models with and without interaction terms. All things considered, our findings reject “greases the wheels” and “trust begets an honest political system” hypotheses. Instead, our finding...

Contribution to the study of the physical stability of the suspensions of zinc oxide, titanium dioxide and precipitated sulphur employing emulsified solid greases like vehicle

International Nuclear Information System (INIS)

Porras Navarro, Martha

2001-01-01

This research evaluated the physical stability of the suspensions of zinc oxide, precipitated sulphur and titanium dioxide. By using emulsified vehicles of three solid greases: stearilic alcohol, stearic acid and beeswax. That varies the concentration of solid grease (2%, 4%, 6 %) and the velocity of agitation for the emulsified vehicle's preparation (250, 500, 750 revolutions by minutes). That got 81 suspensions, 27 for every grease employed. The following effects there were evaluated like indicators of the physical stability of the suspensions: volume of sediment, apparent viscosity, facility of resuspension. There was effected an analysis of the varying of two controlled factors to establish the importance since the statistical viewpoint of the variants of the process over the volume of the sediment. This study indicates that the selection of solid grease is an parameter which influence is significant, what supports the got data through the research. By giving as a result that the stearilic alcohol is the most competent vehicle for the preparation of these suspensions. (Author) [es

Revised Master Plan for the Hood River Production Program, Technical Report 2008.

Energy Technology Data Exchange (ETDEWEB)

Oregon Department of Fish and Wildlife; Confederated Tribes of the Warm Springs Reservation

2008-04-28

The Hood River Production Program (HRPP) is a Bonneville Power Administration (BPA) funded program initiated as a mitigation measure for Columbia River hydrosystem effects on anadromous fish. The HRPP began in the early 1990s with the release of spring Chinook and winter steelhead smolts into the basin. Prior to implementation, co-managers, including the Confederated Tribes of the Warm Springs Reservation and the Oregon Department of Fish and Wildlife drafted the Hood River Production Master Plan (O'Toole and ODFW 1991a; O'Toole and ODFW 1991b) and the Pelton Ladder Master Plan (Smith and CTWSR 1991). Both documents were completed in 1991 and subsequently approved by the Council in 1992 and authorized through a BPA-led Environmental Impact Statement in 1996. In 2003, a 10-year programmatic review was conducted for BPA-funded programs in the Hood River (Underwood et al. 2003). The primary objective of the HRPP Review (Review) was to determine if program goals were being met, and if modifications to program activities would be necessary in order to meet or revise program goals. In 2003, an agreement was signed between PacifiCorp and resource managers to remove the Powerdale Dam (RM 10) and associated adult trapping facility by 2010. The HRPP program has been dependant on the adult trap to collect broodstock for the hatchery programs; therefore, upon the dam's removal, some sort of replacement for the trap would be needed to continue the HRPP. At the same time the Hood River Subbasin Plan (Coccoli 2004) was being written and prompted the co-managers to considered future direction of the program. This included revising the numerical adult fish objectives based on the assimilated data and output from several models run on the Hood River system. In response to the Review as well as the Subbasin Plan, and intensive monitoring and evaluation of the current program, the HRPP co-managers determined the spring Chinook program was not achieving the HRPP

Reduction of exposure to ultrafine particles by kitchen exhaust hoods: the effects of exhaust flow rates, particle size, and burner position.

Science.gov (United States)

Rim, Donghyun; Wallace, Lance; Nabinger, Steven; Persily, Andrew

2012-08-15

Cooking stoves, both gas and electric, are one of the strongest and most common sources of ultrafine particles (UFP) in homes. UFP have been shown to be associated with adverse health effects such as DNA damage and respiratory and cardiovascular diseases. This study investigates the effectiveness of kitchen exhaust hoods in reducing indoor levels of UFP emitted from a gas stove and oven. Measurements in an unoccupied manufactured house monitored size-resolved UFP (2 nm to 100 nm) concentrations from the gas stove and oven while varying range hood flow rate and burner position. The air change rate in the building was measured continuously based on the decay of a tracer gas (sulfur hexafluoride, SF(6)). The results show that range hood flow rate and burner position (front vs. rear) can have strong effects on the reduction of indoor levels of UFP released from the stove and oven, subsequently reducing occupant exposure to UFP. Higher range hood flow rates are generally more effective for UFP reduction, though the reduction varies with particle diameter. The influence of the range hood exhaust is larger for the back burner than for the front burner. The number-weighted particle reductions for range hood flow rates varying between 100 m(3)/h and 680 m(3)/h range from 31% to 94% for the front burner, from 54% to 98% for the back burner, and from 39% to 96% for the oven. Copyright © 2012 Elsevier B.V. All rights reserved.

Treatability and kinetics studies of mesophilic aerobic biodegradation of high oil and grease pet food wastewater

International Nuclear Information System (INIS)

Liu, Victor Lei; Nakhla, G.; Bassi, A.

2004-01-01

In this work, batch activated sludge studies were investigated for the treatment of raw pet food wastewater characterized by oil and grease concentrations of 50,000-66,000 mg/L, COD and BOD concentrations of 100,000 and 80,000 mg/L, respectively, as well as effluent from an existing anaerobic digester treating the aforementioned wastewater. A pre-treatment process, dissolved air flotation (DAF) achieved 97-99% reduction in O and G to about 400-800 mg/L, which is still atypically high for AS. The batch studies were conducted using a 4-L bioreactor at room temperature (21 deg. C) under different conditions. The experimental results showed for the DAF pretreated effluent, 92% COD removal efficiency can be achieved by using conventional activated sludge system at a 5 days contact time and applied initial soluble COD to biomass ratio of 1.17 mg COD/mg VSS. Similarly for the digester effluent at average oil and grease concentrations of 13,500 mg/L, activated sludge affected 63.7-76.2% soluble COD removal at 5 days. The results also showed that all kinetic data best conformed to the zero order biodegradation model with a low biomass specific maximum substrate utilization rate of 0.168 mg COD/mg VSS day reflecting the slow biodegradability of the wastewater even after 99% removal of oil and grease

Frictional properties of lubrication greases with the addition of nickel nanoparticles in pneumatic cylinder

Science.gov (United States)

Chang, Ho; Lan, Chou-Wei; Guo, Jia-Bin

2011-12-01

This paper studies the influence of addition of 100 nm diameter nickel nano-particles on the friction properties of synthetic grease (Li base, VG100) in pneumatic cylinder. The friction force test of pneumatic cylinder equipment measures the frictional force between seal and cylinder bore in pneumatic cylinders. The lubricants with addition of nickel nano-particles were used for lubricating the contact interface between seal and cylinder bore. The friction force test equipment employ a load cell force sensor to measure the friction force between seals and cylinder bores. Results obtained from experimental tests are compared to determine the friction force between seals and cylinder bore in pneumatic cylinders. The study leads to the conclusion that the addition of nickel nano-particles to synthetic grease results in a decrease in friction force between seals and cylinder bores in pneumatic cylinder. This tribological behavior is closely related to the deposition of nano-particles on the rubbing surfaces

ALARA review for the 202-S plutonium loadout hood stabilization

International Nuclear Information System (INIS)

Patch, R.F.

2000-01-01

This as low as reasonably achievable (ALARA) review provides a description of the engineering and administrative controls used to manage personnel exposures, control contamination levels, and control airborne radioactivity concentrations while conducting stabilization of the Reduction-Oxidation (REDOX) Facility plutonium loadout hood and associated piping, and the isolation of the ER-8 ventilation system

Pedestrian protection integrated in the motor hood; Fussgaengerschutz bei Motorhauben

Energy Technology Data Exchange (ETDEWEB)

Hilfrich, E.; Roettger, R.; Zoernack, M.; Patberg, L. [Vertrieb/Engineering, Fahrzeugtechnik, ThyssenKrupp Steel, Duisburg (Germany)

2005-12-01

New legislation provides for better pedestrian protection in case of collision with motor cars. This is a great challenge in car design. ThyssenKrupp Steel are working on concepts for motor hoods that meet these requirements. Steel is the material of choice as it combines effective energy absorption with an excellent cost-benefit ration. (orig.)

Comparison of emissions from selected commercial kitchen appliances and food products

Energy Technology Data Exchange (ETDEWEB)

Kuehn, T.H.; Gerstler, W.D.; Pui, D.Y.H.; Ramsey, J.W.

1999-07-01

Effluents have been measured from various grease-producing cooking processes in an attempt to quantify the emissions that enter typical commercial kitchen exhaust hoods. The appliances tested include gas and electric versions of single-sided griddles, open-vat deep fat fryers, under-fired broilers, full size convection ovens, and six burner ranges. Food products include hamburger, chicken breast, fries, sausage pizza, and a spaghetti meal. Emission data were obtained for particles, grease vapor, CO, CO{sub 2}, NO{sub x}, and hydrocarbons. Velocity and temperature fields were measured in the plume above each appliance. Results show that a large fraction of the grease emission is typically in vapor form. The broilers emit significantly more particles less than 2.5 {micro}m in size (PM 2.5) than the other appliances tested. Combustion by-products were measured for all gas appliances. Both the gas and electric broilers emitted significant amounts of CO when hamburgers were cooked. Aromatic hydrocarbon concentrations were below detectable limits in all tests.

Capture Efficiency of Cooking-Related Fine and Ultrafine Particles by Residential Exhaust Hoods

Energy Technology Data Exchange (ETDEWEB)

Lunden, Melissa M.; Delp, William W.

2014-06-05

Effective exhaust hoods can mitigate the indoor air quality impacts of pollutant emissions from residential cooking. This study reports capture efficiencies (CE) measured for cooking generated particles for scripted cooking procedures in a 121-m3 chamber with kitchenette. CEs also were measured for burner produced CO2 during cooking and separately for pots and pans containing water. The study used four exhaust hoods previously tested by Delp and Singer (Environ. Sci. Technol., 2012, 46, 6167-6173). For pan-frying a hamburger over medium heat on the back burner, CEs for particles were similar to those for burner produced CO2 and mostly above 80percent. For stir-frying green beans in a wok (high heat, front burner), CEs for burner CO2 during cooking varied by hood and airflow: CEs were 34-38percent for low (51?68 L s-1) and 54?72percent for high (109?138 L s-1) settings. CEs for 0.3?2.0 ?m particles during front burner stir-frying were 3?11percent on low and 16?70percent on high settings. Results indicate that CEs measured for burner CO2 are not predictive of CEs of cooking-generated particles under all conditions, but they may be suitable to identify devices with CEs above 80percent both for burner combustion products and for cooking-related particles.

Experimental preliminary exploration on determining grease thickness simulated by paraffin in petroleum pipelines

International Nuclear Information System (INIS)

Zhao Nongxiao; Arkin, Abulim; Yang Kunjie; Wang Shiheng; Shi Feiyue

2009-01-01

1.25 MeV γ-ray of 60 Co Compton scattering coefficient in the simple of paraffin,are measured by γ-ray energy spectrum analysis in two determining means. At the same experimental condition, we have used this scattering coefficient to determining grease thickness simulated by paraffin. The result show the average relative difference is about 1.29% for the best group. (authors)

Mathematical modeling of thermal stresses in basic oxygen furnace hood tubes

Science.gov (United States)

Samarasekera, I. V.

1985-06-01

The stress-strain history of Basic Oxygen Furnace hood tubes during thermal cycling has been computed using heat flow and stress analyses. The steady-state temperature distribution in a transverse section of the tube was computed at a location where gas temperature in the hood could be expected to be a maximum. Calculations were performed for peak gas temperatures in the range 1950 to 2480 °C (3500 to 4500 °F). The stress-strain history of an element of material located at the center of the tube hot face was traced for three consecutive cycles using elasto-plastic finite-element analysis. It has been shown that the state of stress in the element alternates between compression and tension as the tube successively heats and cools. Yielding and plastic flow occurs at the end of each half of a given cycle. It was postulated that owing to repctitive yielding, plastic strain energy accumulates causing failure of the tubes by fatigue in the low cycle region. Using fatigue theory a conservative estimate for tube life was arrived at. In-plant observations support this mechanism of failure, and the number of cycles within which tube cracking was observed compares reasonably with model predictions. Utilizing the heat flow and stress models it was recommended that tube life could be enhanced by changing the tube material to ARMCO 17-4 pH or AISI 405 steel or alternatively reconstructing hoods with AISI 316L tubes of reduced thickness. These recommendations were based on the criterion that low-cycle fatigue failure could be averted if the magnitude of the cyclic strain could be reduced or if macroscopic plastic flow could be prevented.

Efficient production of biodiesel from waste grease: one-pot esterification and transesterification with tandem lipases.

Science.gov (United States)

Yan, Jinyong; Li, Aitao; Xu, Yi; Ngo, Thao P N; Phua, Szechao; Li, Zhi

2012-11-01

A novel concept and efficient method for producing biodiesel (FAME) from grease (15-40wt% free fatty acid, FFA) were developed by using tandem lipases for one-pot esterification of FFA and transesterification of triglyceride with methanol in a solvent-free system. Combining immobilized Candida antarctica lipase B (CALB) (Novozyme 435) favoring the esterification and immobilized Thermomyces lanuginosus lipase (TLL) (Lipozyme TLIM) preferring the transesterification at 2:8 (wt/wt) gave FAME in 80% yield, being better than that with Novozyme 435 or Lipozyme TLIM. Recombinant Escherichia coli (Calb/Tll) co-expressing CALB and TLL was engineered as a more efficient tandem-lipases system. Using wet or dry cells (4wt%) gave FAME in 87% or 95% yield, which is much better than that with E. coli cells expressing either CALB or TLL alone. Cells of E. coli (Calb/Tll) were recycled for five times and retained 75% productivity, thus being practical for producing biodiesel from grease. Copyright © 2012 Elsevier Ltd. All rights reserved.

International evolution of fat, oil and grease (FOG) waste management - A review

OpenAIRE

Wallace, Thomas; Gibbons, David; O'Dwyer, Michael; Curran, Thomas P.

2017-01-01

In recent years, issues relating to fat, oil and grease (FOG) in sewer systems have intensified. In the media, sewer blockages caused by FOG waste deposits, commonly referred to as 'fatbergs', are becoming a reminder of the problems that FOG waste can cause when left untreated. These FOG blockages lead to sanitary sewer overflows, property flooding and contamination of water bodies with sewage. Despite these financial and environmentally detrimental effects, a homogenous FOG waste management ...

Capture efficiency of cooking-related fine and ultrafine particles by residential exhaust hoods.

Science.gov (United States)

Lunden, M M; Delp, W W; Singer, B C

2015-02-01

Effective exhaust hoods can mitigate the indoor air quality impacts of pollutant emissions from residential cooking. This study reports capture efficiencies (CE) measured for cooking-generated particles for scripted cooking procedures in a 121-m3 chamber with kitchenette. CEs also were measured for burner produced CO2 during cooking and separately for pots and pans containing water. The study used four exhaust hoods previously tested by Delp and Singer (Environ. Sci. Technol., 2012, 46, 6167-6173). For pan-frying a hamburger over medium heat on the back burner, CEs for particles were similar to those for burner produced CO2 and mostly above 80%. For stir-frying green beans in a wok (high heat, front burner), CEs for burner CO2 during cooking varied by hood and airflow: CEs were 34-38% for low (51-68 l/s) and 54-72% for high (109-138 l/s) settings. CEs for 0.3-2.0 μm particles during front burner stir-frying were 3-11% on low and 16-70% on high settings. Results indicate that CEs measured for burner CO2 are not predictive of CEs of cooking-generated particles under all conditions, but they may be suitable to identify devices with CEs above 80% both for burner combustion products and for cooking-related particles. Published 2014. This article is a U.S. Government work and is in the public domain in the USA.

Archeological Testing Fort Hood: 1994-1995. Volume 2

Science.gov (United States)

1996-10-01

ASSOCI TES, INC. (662-22) Archeological Testing at Fort Hood. 1994-199.5 569 -48-1941.1080-134 1935 -058 Figure 7.17 Selected Perforator Types: Awl and...Department of Anthropology, University of Arkansas. Huskey, V. 1935 An Archeological Survey of the Nueces Canyon of Texas, Bulletin of the Texas... epr 064lL.Tan I lms expected 08-FH1 Yellow 4 expected expedctd cd .9 15.Q W n• I less M 0 ~ *~Tax~on Total Total Inmr 53 nac na Vertebra.es 1. FcAuifnm

Hood River Steelhead Genetics Study; Relative Reproductive Success of Hatchery and Wild Steelhead in the Hood River, Final Report 2002-2003.

Energy Technology Data Exchange (ETDEWEB)

Blouin, Michael

2003-05-01

There is a considerable interest in using hatcheries to speed the recovery of wild populations. The Bonneville Power Administration (BPA), under the authority of the Northwest Power Planning Act, is currently funding several hatchery programs in the Columbia Basin as off-site mitigation for impacts to salmon and steelhead caused by the Columbia River federal hydropower system. One such project is located on the Hood River, an Oregon tributary of the Columbia. These hatchery programs cost the region millions of dollars. However, whether such programs actually improve the status of wild fish remains untested. The goal of this project was to evaluate the effectiveness of the Hood River hatchery program as required by the Northwest Power Planning Council Fish and Wildlife Program, by the Oregon Plan for Coastal Salmonids, by NMFS ESA Section 4(d) rulings, and by the Oregon Department of Fish and Wildlife (ODFW) Wild Fish Management Policy (OAR 635-07-525 through 529) and the ODFW Hatchery Fish Gene Resource Management Policy (OAR 635-07-540 through 541). The Hood River supports two populations of steelhead, a summer run and a winter run. They spawn only above the Powerdale Dam, which is a complete barrier to all salmonids. Since 1991 every adult passed above the dam has been measured, cataloged and sampled for scales. Therefore, we have a DNA sample from every adult steelhead that went over the dam to potentially spawn in the Hood River from 1991 to the present. Similar numbers of hatchery and wild fish have been passed above the dam during the last decade. During the 1990's 'old' domesticated hatchery stocks of each run (multiple generations in the hatchery, out-of-basin origin; hereafter H{sub old}) were phased out, and conservation hatchery programs were started for the purpose of supplementing the two wild populations (hereafter 'new' hatchery stocks, H{sub new}). These samples gave us the unprecedented ability to estimate, via

Greasing the Wheels of Trade: measuring the Dutch transaction with occupational data

OpenAIRE

Dalen, Hendrik; Vuuren, Aico

2003-01-01

textabstractHow much does a nation spend on resources to 'grease the wheels of trade'? To examine this question the Dutch economy is used as an exemplary case as the Netherlands are known as a nation of traders. This image was derived in the seventeenth century from successes in long distance trade, shipping and financial innovations. Despite its historical background in trading the potential to 'truck and barter' has never been adequately measured. In this paper we present a first attempt in...

Experimental Comparison of the Behavior between Base Oil and Grease Starvation Based on Inlet Film Thickness

Directory of Open Access Journals (Sweden)

D. Kostal

2017-03-01

Full Text Available This paper deals with the experimental study of an elastohydrodynamic contact under conditions of insufficient lubricant supply. Starvation level of this type of the contact may be experimentally determined based on the position of the meniscus, but this way can't determine all levels of starvation. Consequent development in the field of tribology achieved theoretical model that can determine all levels of starvation by dependency on the thickness of the lubricant film entering the contact, but it is difficult for experimental verification. The main goal of this work is an experimental study and description of the behavior of the elastohydrodynamic contact with controlled thickness of the lubricant film at the contact input. Contact was lubricated by the base oil and the grease and compared. Results were surprising because the only differences between oil and grease were observed for more viscous lubricants at thicker film layer entering to the contact.

Solar Alpha Rotary Joint (SARJ) Lubrication Interval Test and Evaluation (LITE). Post-Test Grease Analysis

Science.gov (United States)

Golden, Johnny L.; Martinez, James E.; Devivar, Rodrigo V.

2015-01-01

The Solar Alpha Rotary Joint (SARJ) is a mechanism of the International Space Station (ISS) that orients the solar power generating arrays toward the sun as the ISS orbits our planet. The orientation with the sun must be maintained to fully charge the ISS batteries and maintain all the other ISS electrical systems operating properly. In 2007, just a few months after full deployment, the starboard SARJ developed anomalies that warranted a full investigation including ISS Extravehicular Activity (EVA). The EVA uncovered unexpected debris that was due to degradation of a nitride layer on the SARJ bearing race. ISS personnel identified the failure root-cause and applied an aerospace grease to lubricate the area associated with the anomaly. The corrective action allowed the starboard SARJ to continue operating within the specified engineering parameters. The SARJ LITE (Lubrication Interval Test and Evaluation) program was initiated by NASA, Lockheed Martin, and Boeing to simulate the operation of the ISS SARJ for an extended time. The hardware was designed to test and evaluate the exact material components used aboard the ISS SARJ, but in a controlled area where engineers could continuously monitor the performance. After running the SARJ LITE test for an equivalent of 36+ years of continuous use, the test was opened to evaluate the metallography and lubrication. We have sampled the SARJ LITE rollers and plate to fully assess the grease used for lubrication. Chemical and thermal analysis of these samples has generated information that has allowed us to assess the location, migration, and current condition of the grease. The collective information will be key toward understanding and circumventing any performance deviations involving the ISS SARJ in the years to come.

Carbon Dioxide Exposure Resulting From Hood Protective Equipment Used in Joint Arthroplasty Surgery.

Science.gov (United States)

Patel, Suhani; Fine, Janelle M; Lim, Michael J; Copp, Steven N; Rosen, Adam S; West, John B; Prisk, G Kim

2017-08-01

To protect both the surgeon and patient during procedures, hooded protection shields are used during joint arthroplasty procedures. Headache, malaise, and dizziness, consistent with increased carbon dioxide (CO 2 ) exposure, have been anecdotally reported by surgeons using hoods. We hypothesized that increased CO 2 concentrations were causing reported symptoms. Six healthy subjects (4 men) donned hooded protection, fan at the highest setting. Arm cycle ergometry at workloads of 12 and 25 watts (W) simulated workloads encountered during arthroplasty. Inspired O 2 and CO 2 concentrations at the nares were continuously measured at rest, 12 W, and 25 W. At each activity level, the fan was deactivated and the times for CO 2 to reach 0.5% and 1.0% were measured. At rest, inspired CO 2 was 0.14% ± 0.04%. Exercise had significant effect on CO 2 compared with rest (0.26% ± 0.08% at 12 W, P = .04; 0.31% ± 0.05% at 25 W, P = .003). Inspired CO 2 concentration increased rapidly with fan deactivation, with the time for CO 2 to increase to 0.5% and 1.0% after fan deactivation being rapid but variable (0.5%, 12 ± 9 seconds; 1%, 26 ± 15 seconds). Time for CO 2 to return below 0.5% after fan reactivation was 20 ± 37 seconds. During simulated joint arthroplasty, CO 2 remained within Occupational Safety and Health Administration (OSHA) standards with the fan at the highest setting. With fan deactivation, CO 2 concentration rapidly exceeds OSHA standards. Copyright © 2017 Elsevier Inc. All rights reserved.

Study the velocity and pressure exerted in front of the filter surface in the kitchen hood system by using ANSYS

Science.gov (United States)

Asmuin, Norzelawati; Pairan, M. Rasidi; Isa, Norasikin Mat; Sies, Farid

2017-04-01

Commercial kitchen hood ventilation system is a device used to capture and filtered the plumes from cooking activities in the kitchen area. Nowadays, it is very popular in the industrial sector such as restaurant and hotel to provide hygiene food. This study focused at the KSA filter part which installed in the kitchen hood system, the purpose of this study is to identify the critical region which indicated by observing the velocity and pressure of plumes exerted at of KSA filter. It is important to know the critical location of the KSA filter in order to install the nozzle which will helps increase the filtration effectiveness. The ANSYS 16.1 (FLUENT) software as a tool used to simulate the kitchen hood systems which consist of KSA filter. The commercial kitchen hood system model has a dimension 700 mm width, 1600 mm length and 555 mm height. The system has two inlets and one outlet. The velocity of the plumes is set to be 0.235m/s and the velocity of the inlet capture jet is set to be 1.078m/s. The KSA filter is placed 45 degree from the y axis. The result shows the plumes has more tendency flowing pass through at the bottom part of KSA filter.

Thermophilic anaerobic co-digestion of sewage sludge with grease waste: Effect of long chain fatty acids in the methane yield and its dewatering properties

International Nuclear Information System (INIS)

Silvestre, G.; Illa, J.; Fernández, B.; Bonmatí, A.

2014-01-01

Highlights: • Thermophilic anaerobic codigestion of sewage sludge and grease waste (GW) doubles methane yield. • High GW doses in the influent leads to instability and LCFA accumulation in the effluent. • GW addition promotes acetoclastic activity whilst worsening the hydrogenothrophic activity. • The mesophilic codigestion with GW performs better than the thermophilic one. - Abstract: Thermophilic co-digestion of sewage sludge with three different doses of trapped grease waste (GW) from the pre-treatment of a WWTP has been assessed in a CSTR bench-scale reactor. After adding 12% and 27% of grease waste (on COD basis), the organic loading rate increased from 2.2 to 2.3 and 2.8 kg COD m −3 d −1 respectively, and the methane yield increased 1.2 and 2.2 times. Further GW increase (37% on COD basis) resulted in an unstable methane yield and in long chain fatty acids (LCFA) accumulation. Although this inestability, the presence of volatile fatty acids in the effluent was negligible, showing good adaptation to fats of the thermophilic biomass. Nevertheless, the presence of LCFA in the effluent worsens its dewatering properties. Specific methanogenic activity tests showed that the addition of grease waste ameliorates the acetoclastic activity in detriment of the hydrogenotrophic activity, and suggests that the tolerance to LCFA can be further enhanced by slowly increasing the addition of lipid-rich materials

Hood River Production Program Monitoring and Evaluation (M&E) - Confederated Tribes of Warm Springs : Annual Report For Fiscal Year, October 2007 – September 2008.

Energy Technology Data Exchange (ETDEWEB)

Gerstenberger, Ryan [Confederated Tribes of Warm Springs Reservation

2009-07-27

This progress report describes work performed by the Confederated Tribes of Warm Springs (CTWSRO) portion of the Hood River Production Program Monitoring and Evaluation Project (HRPP) during the 2008 fiscal year. A total of 64,736 hatchery winter steelhead, 12,108 hatchery summer steelhead, and 68,426 hatchery spring Chinook salmon smolts were acclimated and released in the Hood River basin during the spring. The HRPP exceeded program goals for a release of and 50,000 winter steelhead but fell short of the steelhead release goals of 30,000 summer steelhead and 75,000 spring Chinook in 2008. Passive Integrated Transponders (PIT) tags were implanted in 6,652 hatchery winter steelhead, and 1,196 hatchery summer steelhead, to compare migratory attributes and survival rates of hatchery fish released into the Hood River. Water temperatures were recorded at six locations within the Hood River subbasin to monitor for compliance with Oregon Department of Environmental Quality water quality standards. A preseason spring Chinook salmon adult run forecast was generated, which predicted an abundant return adequate to meet escapement goal and brood stock needs. As a result the tribal and sport fisheries were opened. A tribal creel was conducted from May 22 to July 18 during which an estimated 172 spring Chinook were harvested. One hundred sixteen Spring Chinook salmon redds were observed and 72 carcasses were inspected on 19.4 miles of spawning grounds throughout the Hood River Basin during 2008. Annual salvage operations were completed in two irrigation canals resulting in the liberation of 1,641 fish back to the Hood River.

How the Cobra Got Its Flesh-Eating Venom: Cytotoxicity as a Defensive Innovation and Its Co-Evolution with Hooding, Aposematic Marking, and Spitting

Directory of Open Access Journals (Sweden)

Nadya Panagides

2017-03-01

Full Text Available The cytotoxicity of the venom of 25 species of Old World elapid snake was tested and compared with the morphological and behavioural adaptations of hooding and spitting. We determined that, contrary to previous assumptions, the venoms of spitting species are not consistently more cytotoxic than those of closely related non-spitting species. While this correlation between spitting and non-spitting was found among African cobras, it was not present among Asian cobras. On the other hand, a consistent positive correlation was observed between cytotoxicity and utilisation of the defensive hooding display that cobras are famous for. Hooding and spitting are widely regarded as defensive adaptations, but it has hitherto been uncertain whether cytotoxicity serves a defensive purpose or is somehow useful in prey subjugation. The results of this study suggest that cytotoxicity evolved primarily as a defensive innovation and that it has co-evolved twice alongside hooding behavior: once in the Hemachatus + Naja and again independently in the king cobras (Ophiophagus. There was a significant increase of cytotoxicity in the Asian Naja linked to the evolution of bold aposematic hood markings, reinforcing the link between hooding and the evolution of defensive cytotoxic venoms. In parallel, lineages with increased cytotoxicity but lacking bold hood patterns evolved aposematic markers in the form of high contrast body banding. The results also indicate that, secondary to the evolution of venom rich in cytotoxins, spitting has evolved three times independently: once within the African Naja, once within the Asian Naja, and once in the Hemachatus genus. The evolution of cytotoxic venom thus appears to facilitate the evolution of defensive spitting behaviour. In contrast, a secondary loss of cytotoxicity and reduction of the hood occurred in the water cobra Naja annulata, which possesses streamlined neurotoxic venom similar to that of other aquatic elapid snakes (e

How the Cobra Got Its Flesh-Eating Venom: Cytotoxicity as a Defensive Innovation and Its Co-Evolution with Hooding, Aposematic Marking, and Spitting.

Science.gov (United States)

Panagides, Nadya; Jackson, Timothy N W; Ikonomopoulou, Maria P; Arbuckle, Kevin; Pretzler, Rudolf; Yang, Daryl C; Ali, Syed A; Koludarov, Ivan; Dobson, James; Sanker, Brittany; Asselin, Angelique; Santana, Renan C; Hendrikx, Iwan; van der Ploeg, Harold; Tai-A-Pin, Jeremie; van den Bergh, Romilly; Kerkkamp, Harald M I; Vonk, Freek J; Naude, Arno; Strydom, Morné A; Jacobsz, Louis; Dunstan, Nathan; Jaeger, Marc; Hodgson, Wayne C; Miles, John; Fry, Bryan G

2017-03-13

The cytotoxicity of the venom of 25 species of Old World elapid snake was tested and compared with the morphological and behavioural adaptations of hooding and spitting. We determined that, contrary to previous assumptions, the venoms of spitting species are not consistently more cytotoxic than those of closely related non-spitting species. While this correlation between spitting and non-spitting was found among African cobras, it was not present among Asian cobras. On the other hand, a consistent positive correlation was observed between cytotoxicity and utilisation of the defensive hooding display that cobras are famous for. Hooding and spitting are widely regarded as defensive adaptations, but it has hitherto been uncertain whether cytotoxicity serves a defensive purpose or is somehow useful in prey subjugation. The results of this study suggest that cytotoxicity evolved primarily as a defensive innovation and that it has co-evolved twice alongside hooding behavior: once in the Hemachatus + Naja and again independently in the king cobras ( Ophiophagus ). There was a significant increase of cytotoxicity in the Asian Naja linked to the evolution of bold aposematic hood markings, reinforcing the link between hooding and the evolution of defensive cytotoxic venoms. In parallel, lineages with increased cytotoxicity but lacking bold hood patterns evolved aposematic markers in the form of high contrast body banding. The results also indicate that, secondary to the evolution of venom rich in cytotoxins, spitting has evolved three times independently: once within the African Naja , once within the Asian Naja , and once in the Hemachatus genus. The evolution of cytotoxic venom thus appears to facilitate the evolution of defensive spitting behaviour. In contrast, a secondary loss of cytotoxicity and reduction of the hood occurred in the water cobra Naja annulata , which possesses streamlined neurotoxic venom similar to that of other aquatic elapid snakes (e.g., hydrophiine

Review of inservice inspections of greased tendons in prestressed-concrete containments

International Nuclear Information System (INIS)

Dougan, J.R.; Ashar, H.

1983-01-01

Prestressed-concrete containments in the United States using greased prestressing tendons are inspected periodically to ensure structural integrity and to identify and correct problem areas before they become critical. An analysis of the available utility inspection data and an evaluation of the current and proposed guidelines were conducted to provide a measure of the reliability of the inspection process. Comments from utility and industry personnel were factored into the analysis. The results indicated that the majority of the few incidences of problems or abnormalities which occurred were minor in nature and did not threaten the structural integrity of the containment

Construction and Operation of a Ventilated Hood System for Measuring Greenhouse Gas and Volatile Organic Compound Emissions from Cattle

Directory of Open Access Journals (Sweden)

Yongjing Zhao

2011-12-01

Full Text Available Recent interest in greenhouse gas emissions from ruminants, such as cattle, has spawned a need for affordable, precise, and accurate methods for the measurement of gaseous emissions arising from enteric fermentation. A new head hood system for cattle designed to capture and quantify emissions was recently developed at the University of California, Davis. The system consists of two head hoods, two vacuum pumps, and an instrumentation cabinet housing the required data collection equipment. This system has the capability of measuring carbon dioxide, methane, ethanol, methanol, water vapor, nitrous oxide, acetic acid emissions and oxygen consumption in real-time. A unique aspect of the hoods is the front, back, and sides are made of clear polycarbonate sheeting allowing the cattle a full range of vision during gas sampling. Recovery rates for these slightly negative pressure chambers were measured ranging from 97.6 to 99.3 percent. This system can capture high quality data for use in improving emission inventories and evaluating gaseous emission mitigation strategies.

Green diesel production via catalytic hydrogenation/decarboxylation of triglycerides and fatty acids of vegetable oil and brown grease

Science.gov (United States)

Sari, Elvan

Increase in the petroleum prices, projected increases in the world's energy demand and environmental awareness have shifted the research interest to the alternative fuel technologies. In particular, green diesel, vegetable oil/animal fat/waste oil and grease derived hydrocarbons in diesel boiling range, has become an attractive alternative to biodiesel---a mixture of fatty acid methyl esters, particularly due to its superior fuel properties that are similar to petroleum diesel. Hence, green diesel can be used as a drop-in fuel in the current diesel engines. The current technology for production of green diesel-hydrodeoxygenation of triglycerides and fatty acids over conventional hydrotreating catalysts suffers from fast catalyst deactivation in the absence of hydrogen combined with high temperatures and high fatty acid content in the feedstock. Additionally, excess hydrogen requirement for hydrodeoxygenation technique leads to high production costs. This thesis proposes a new technology-selective decarboxylation of brown grease, which is a mixture of fats and oils collected from waste water trap and rich in fatty acids, over a supported noble metal catalyst that overcomes the green diesel production challenges. In contrast to other feedstocks used for liquid biofuel production, brown grease is inexpensive and non-food competing feedstock, therefore the process finds solution to waste management issues, reduces the renewable fuel production cost and does not add to the global food shortage problems. Special catalyst formulations were developed to have a high activity and stability in the absence of hydrogen in the fatty acid decarboxylation process. The study shows how catalyst innovations can lead to a new technology that overcomes the process challenges. First, the effect of reaction parameters on the activity and the selectivity of brown grease decarboxylation with minimum hydrogen consumption over an activated carbon supported palladium catalyst were

Subscale hood seal test topical report

Energy Technology Data Exchange (ETDEWEB)

Versteeg, J.L.; Herold, B.A.; McClintic, J.K.; Schmall, R.A.; Hoetzl, M.

1991-09-06

To maximize the transfer of heat from the recirculated gases to the scrap, it is essential to percolate as much of the gases as possible through the scrap. To accomplish this flow path and avoid the bypassing of hot gas around the scrap, the seal between the preheater hood and the scrap bucket must be relatively tight. These tests which are described in this report were designed to measure the performance of several possible seal designs under simulated operating conditions. At the conclusion of the tests, one design was recommended as the primary arrangement with another design considered as an alternate. Both designs met the criteria of low leakage but one design was preferred due an expected greater resistance to wear. The test results also provided valuable information for estimating seal leakage in the full scale installation.

Influence of impact speed on head and brain injury outcome in vulnerable road user impacts to the car hood.

Science.gov (United States)

Fredriksson, Rikard; Zhang, Liying; Boström, Ola; Yang, King

2007-10-01

EuroNCAP and regulations in Europe and Japan evaluate the pedestrian protection performance of cars. The test methods are similar and they all have requirements for the passive protection of the hood area at a pedestrian to car impact speed of 40 km/h. In Europe, a proposal for a second phase of the regulation mandates a brake-assist system along with passive requirements. The system assists the driver in optimizing the braking performance during panic braking, resulting in activation only when the driver brakes sufficiently. In a European study this was estimated to occur in about 50% of pedestrian accidents. A future system for brake assistance will likely include automatic braking, in response to a pre-crash sensor, to avoid or mitigate injuries of vulnerable road users. An important question is whether these systems will provide sufficient protection, or if a parallel, passive pedestrian protection system will be necessary. This study investigated the influence of impact speed on head and brain injury risk, in impacts to the carhood. One car model was chosen and a rigid adjustable plate was mounted under the hood. Free-flying headform impacts were carried out at 20 and 30 km/h head impact velocities at different under-hood distances, 20 to 100 mm; and were compared to earlier tests at 40 km/h. The EEVC WG17 adult pedestrian headform was used for non-rotating tests and a Hybrid III adult 50th percentile head was used for rotational tests where linear and rotational acceleration was measured. Data from the rotational tests was used as input to a validated finite element model of the human head, the Wayne State University Head Injury Model (WSUHIM). The model was utilized to assess brain injury risk and potential injury mechanism in a pedestrian-hood impact. Although this study showed that it was not necessarily true that a lower HIC value reduced the risk for brain injury, it appeared, for the tested car model, under-hood distances of 60 mm in 20 km/h and 80 mm

Semi-continuous anaerobic co-digestion of thickened waste activated sludge and fat, oil and grease

International Nuclear Information System (INIS)

Wan Caixia; Zhou Quancheng; Fu Guiming; Li Yebo

2011-01-01

Highlights: → Co-digestion of thickened waste activated sludge (TWAS) with fat, oil and grease (FOG). → Co-digestion of TWAS and FOG at 64% VS increased biogas production by 137%. → FOG addition ratio at 74% of total VS caused inhibition of the anaerobic digestion process. → Micronutrients addition did not significantly improve the biogas production and digestion stabilization. - Abstract: Co-digestion of thickened waste activated sludge (TWAS) and fat, oil and grease (FOG) was conducted semi-continuously under mesophilic conditions. The results showed that daily methane yield at the steady state was 598 L/kg VS added when TWAS and FOG (64% of total VS) were co-digested, which was 137% higher than that obtained from digestion of TWAS alone. The biogas composition was stabilized at a CH 4 and CO 2 content of 66.8% and 29.5%, respectively. Micronutrients added to co-digestion did not improve the biogas production and digestion stabilization. With a higher addition of FOG (74% of total VS), the digester initially failed but was slowly self-recovered; however, the methane yield was only about 50% of a healthy reactor with the same organic loading rate.

Mount Hood volcano: phase zero study. Final report, January 1, 1977--June 30 1977

Energy Technology Data Exchange (ETDEWEB)

Hull, D.A.

1977-08-04

A base of earth science data was developed for an area centered on Mt. Hood Volcano as the first step in a systematic geothermal resource assessment. A comprehensive technical plan for the assessment was developed and is also described. A preliminary bibliography is included.

Beyond 2001: a silvicultural odyssey to sustaining terrestrial and aquatic ecosystems? Proceedings of the 2001 national silviculture workshop, May 6-10, Hood River, Oregon.

Science.gov (United States)

Sharon Parker; Susan Stevens. Hummel

2002-01-01

The 2001 National Silviculture Workshop was held in Hood River, Oregon, and hosted by the Mt. Hood National Forest, the Gifford Pinchot National Forest, and the Pacific Northwest Research Station. The Washington Office Vegetation Management and Protection Research and Forest and Grassland staffs are ongoing sponsors of the biennial workshop, which began in 1973 in...

Carbon epoxy front hood for an electrical city vehicle

Directory of Open Access Journals (Sweden)

Bere Paul

2017-01-01

Full Text Available In the last decade fiber-reinforced polymer (FRP had a very impressive development. Due to its physical and mechanical properties, this material is used in many high-end domains such as: aerospace, aviation, automotive, medical, engineering or building constructions. In the last period FRP are being intensely used in the automotive industry especially for the chassis manufacturing and other vehicle structural components. In this paper, the authors present the model of a carbon epoxy front hood of a two-passenger electrical car which is specially designed in urban area and which makes use of advanced FRP manufacturing.

The gut microbiome of hooded cranes (Grus monacha) wintering at Shengjin Lake, China.

Science.gov (United States)

Zhao, Guanghong; Zhou, Lizhi; Dong, Yuanqiu; Cheng, Yuanyuan; Song, Yunwei

2017-06-01

Gut microbes of animals play critical roles in processes such as digestion and immunity. Therefore, identifying gut microbes will shed light on understanding the annual life of animal species, particularly those that are threatened or endangered. In the present study, we conducted nucleotide sequence analyses of the 16S rRNA genes of gut microbiome of the hooded cranes (Grus monacha) wintering at Shengjin Lake, China, by Illumina high-throughput sequencing technology. We acquired 503,398 high-quality sequences and 785 operational taxonomic units (OTUs) from 15 fecal samples from different cranes, representing 22 phyla that were dominated by Firmicutes, Proteobacteria, and Actinobacteria. A total of 305 genera were identified that were dominated by Clostridium, Lysinibacillus, and Enterobacter. The core gut microbiome comprised 26 genera, including many probiotic species such as Clostridium, Bacillus, Cellulosilyticum, and Cellulomonas that could catabolize cellulose. The findings reported here contribute to our knowledge of the microbiology of hooded cranes and will likely advance efforts to protect waterbirds that inhabit Shengjin Lake Reserve during winter. © 2017 The Authors. MicrobiologyOpen published by John Wiley & Sons Ltd.

Measurements and predictions of hooded crow (Corvus corone cornix) call propagation over open field habitats

DEFF Research Database (Denmark)

Jensen, Kenneth Kragh; Larsen, Ole Næsbye; Attenborough, Keith

2008-01-01

In a study of hooded crow communication over open fields an excellent correspondence is found between the attenuation spectra predicted by a "turbulence-modified ground effect plus atmospheric absorption" model, and crow call attenuation data. Sound propagation predictions and background noise...

Development and evaluation of emulsifying systems of the material grease from Brazilian flora

Directory of Open Access Journals (Sweden)

Douglas Dourado

2015-10-01

Full Text Available Context: Oils and butter of seed from Brazilian biodiversity are extending the range of innovative products for cosmetics development. They have a fat potential similar to skin composition, leading to the improved performance of these product. Aims: Improve the emulsions spreadability through prior screening of grease composition and studying the viscosity, and the emulsions accelerated stability. Methods: Emulsions were formulated using oils from semiarid plants from Bahia: Syagrus coronate, Pachira retusa, and Pachira aquatica, so as to compare them with oils already standard in the production of cosmetics. Spreadability and stability tests were made comparing the results. The same criteria were used with Amazon seed butter: Virola surinamensis, Butyrospermum parkii, Astrocaryum murumuru, Theobroma cacao and Theobroma grandiflorum. For the emulsions screening and performance, a system was developed for oil/ butter, following tests of accelerated stability, viscosity, and spreadability. Results: The combined system of spreadability was optimized using screening. Emollients containing oleic and palmitic acids, and light chain fatty acids obtained good spreadability. The oil emulsion containing Pachira retusa and Virola surinamensis butter had a higher viscosity. Conclusions: With high content of fatty acids such as oleic, palmitic or the light chain fatty acids obtain an appropriated appearance, texture, and spreadability for cosmetic use. Thus, oils with a low fatty acid content may be combined with butter that have a high fatty acid content and vice-versa. Analyzing and strategically combining grease composition, one can optimize the performance of cosmetic formulations.

End-use energy characterization and conservation potentials at DoD Facilities: An analysis of electricity use at Fort Hood, Texas

Energy Technology Data Exchange (ETDEWEB)

Akbari, H.; Konopacki, S.

1995-05-01

This report discusses the application of the LBL`s End-use Disaggregation Algorithm (EDA) to a DoD installation and presents hourly reconciled end-use data for all major building types and end uses. The project initially focused on achieving these objectives and pilot-testing the methodology at Fort Hood, Texas. Fort Hood, with over 5000 buildings was determined to have representative samples of nearly all of the major building types in use on DoD installations. These building types at Fort Hood include: office, administration, vehicle maintenance, shop, hospital, grocery store, retail store, car wash, church, restaurant, single-family detached housing, two and four-plex housings, and apartment building. Up to 11 end uses were developed for each prototype, consisting of 9 electric and 2 gas; however, only electric end uses were reconciled against known data and weather conditions. The electric end uses are space cooling, ventilation, cooking, miscellaneous/plugs, refrigeration, exterior lighting, interior lighting, process loads, and street lighting. The gas end uses are space heating and hot water heating. Space heating energy-use intensities were simulated only. The EDA was applied to 10 separate feeders from the three substations at Fort Hood. The results from the analyses of these ten feeders were extrapolated to estimate energy use by end use for the entire installation. The results show that administration, residential, and the bar-rack buildings are the largest consumers of electricity for a total of 250GWh per year (74% of annual consumption). By end use, cooling, ventilation, miscellaneous, and indoor lighting consume almost 84% of total electricity use. The contribution to the peak power demand is highest by residential sector (35%, 24 MW), followed by administration buildings (30%), and barrack (14%). For the entire Fort Hood installation, cooling is 54% of the peak demand (38 MW), followed by interior lighting at 18%, and miscellaneous end uses by 12%.

Propiedades fisicoquímicas y tribológicas de una grasa grafitada de Jatropha curcas L y jabón de litio//Physicochemical and tribological properties of graphite grease based on Jatrophacurcas L oil and lithium soap

Directory of Open Access Journals (Sweden)

Juliano‐Chitue de Assunção‐Nascimento

2014-08-01

Full Text Available Las grasas lubricantes son consideradas una dispersión coloidal de un espesante en un fluido lubricante. Los aceites vegetales son ampliamente usados en muchas formulaciones de grasas. En este trabajo se determinaron las propiedades fisicoquímicas y tribológicas de una grasa lubricante fabricada con aceite vegetal de Jatropha curcas L y jabón de litio (JC1G5. Alfa tocoferol acetato y grafito fueron usados como aditivos antioxidante y de extrema presión respectivamente. La grasa JC1G5 mostró un color negro, una temperatura de goteo de 140 oC, apropiadas propiedades de corrosión al cobre y un grado de consistencia NLGI Grado1. El efecto de la lubricación de la grasa JC1G5 fue probado, empleando una máquina de cuatro bolas y un tribómetro timken. Los resultados indican que la grasa JC1G5 posee propiedades tribológicas comparables con una grasa mineral de jabón de litio.Palabras claves: grasa, jatropha curcas L, jabón de litio, propiedades fisicoquímicas, propiedades tribológicas.______________________________________________________________________________AbstractLubricating greases are considered as colloidal dispersions of a thickener in a lubricating fluid. The vegetable oils are widely used in many formulations of greases. In this paper were determined the physicochemical and tribological properties of graphite grease based on Jatropha curcas L vegetableoil and lithium soap (JC1G5. Alpha tocofherol acetate and graphite were used as antioxidant and extreme pressure additives respectively. The grease JC1G5 showed a black color, a dropping point of 140 oC, appropriate magnitude of copper corrosion and consistency NLGI Grade 1. Lubrication performance of the grease JC1G5 was tested using the 4-ball wear tester and timken tribometer tester. Results indicate that the grease JC1G5 has tribological properties comparable to that of mineral oil base lithium grease.Key words: grease, jatrophacurcas L, lithium soap, physicochemical

MOUNT HOOD WILDERNESS AND ADJACENT AREAS, OREGON.

Science.gov (United States)

Keith, T.E.C.; Causey, J.D.

1984-01-01

A mineral survey of the Mount Hood Wilderness, Oregon, was conducted. Geochemical data indicate two areas of substantiated mineral-resource potential containing weak epithermal mineralization: an area of the north side of Zigzag Mountain where vein-type lead-zinc-silver deposits occur and an area of the south side of Zigzag Mountain, where the upper part of a quartz diorite pluton has propylitic alteration associated with mineralization of copper, gold, silver, lead, and zinc in discontinuous veins. Geothermal-resource potential for low- to intermediate-temperature (less than 248 degree F) hot-water systems in the wilderness is probable in these areas. Part of the wilderness is classified as a Known Geothermal Resource Area (KGRA), which is considered to have probable geothermal-resource potential, and two parts of the wilderness have been included in geothermal lease areas.

Soil clean up by vapour extraction: parametrical study; Depollution des sols par extraction sous pression reduite: etude de quelques parametres

Energy Technology Data Exchange (ETDEWEB)

Dutheil, C.

2003-05-15

Soil vapour extraction is a treatment process for soils polluted by volatile organic compounds. Its principle relies on the circulation of gaseous flow in soil by the application of a depression of some hundreds milli-bars. A parametrical study has been led on a soil artificially polluted by tri-chloro-ethene. It shows that the gaseous flow rate has a slight influence on pollutants extraction yield. This is due to rate limited mass transfer processes. Soil moisture plays a negative role on treatment efficiency because of the reduction of the porosity available for the gas circulation. Tests have been performed on a soil polluted by a complex mixture of organic pollutants to elaborate a methodology of technical feasibility assessment. This methodology aims at identifying and limiting risks of site rehabilitation failure. Tests results show that soil vapour extraction was inadequate to treat the soil tested in this study because of the strong affinity between a dense organic phase (grease) and chlorinated solvents. (author)

Microbial community adaptation influences long-chain fatty acid conversion during anaerobic codigestion of fats, oils, and grease with municipal sludge.

Science.gov (United States)

Ziels, Ryan M; Karlsson, Anna; Beck, David A C; Ejlertsson, Jörgen; Yekta, Sepehr Shakeri; Bjorn, Annika; Stensel, H David; Svensson, Bo H

2016-10-15

Codigesting fats, oils, and greases with municipal wastewater sludge can greatly improve biomethane recovery at wastewater treatment facilities. Process loading rates of fats, oils, and greases have been previously tested with little knowledge of the digester microbial community structure, and high transient fat loadings have led to long chain fatty acid (LCFA) accumulation and digester upsets. This study utilized recently-developed quantitative PCR assays for syntrophic LCFA-degrading bacteria along with 16S amplicon sequencing to relate changes in microbial community structure to LCFA accumulation during transient loading increases to an anaerobic codigester receiving waste restaurant oil and municipal wastewater sludge. The 16S rRNA gene concentration of the syntrophic β-oxidizing genus Syntrophomonas increased to ∼15% of the Bacteria community in the codigester, but stayed below 3% in the control digester that was fed only wastewater sludge. Methanosaeta and Methanospirillum were the dominant methanogenic genera enriched in the codigester, and together comprised over 80% of the Archaea community by the end of the experimental period. Constrained ordination showed that changes in the codigester Bacteria and Archaea community structures were related to measures of digester performance. Notably, the effluent LCFA concentration in the codigester was positively correlated to the specific loading rate of waste oil normalized to the Syntrophomonas 16S rRNA concentration. Specific loading rates of 0-1.5 × 10(-12) g VS oil/16S gene copies-day resulted in LCFA concentrations below 30 mg/g TS, whereas LCFA accumulated up to 104 mg/g TS at higher transient loading rates. Based on the community-dependent loading limitations found, enhanced biomethane production from high loadings of fats, oils and greases can be achieved by promoting a higher biomass of slow-growing syntrophic consortia, such as with longer digester solids retention times. This work also

Agriculture and Rural Development on Fort Hood Lands, 1849-1942: National Register Assessments of 710 Historic Archeological Properties

National Research Council Canada - National Science Library

Freeman, Martha

2001-01-01

In 1999, historians consulting with Prewitt & Associates, Inc., conducted archival research for the purpose of developing historic contexts relevant to the Fort Hood lands taken during the 1940s acquisition...

A review of Brucella infection in marine mammals, with special emphasis on Brucella pinnipedialis in the hooded seal (Cystophora cristata)

Science.gov (United States)

2011-01-01

Brucella spp. were isolated from marine mammals for the first time in 1994. Two novel species were later included in the genus; Brucella ceti and Brucella pinnipedialis, with cetaceans and seals as their preferred hosts, respectively. Brucella spp. have since been isolated from a variety of marine mammals. Pathological changes, including lesions of the reproductive organs and associated abortions, have only been registered in cetaceans. The zoonotic potential differs among the marine mammal Brucella strains. Many techniques, both classical typing and molecular microbiology, have been utilised for characterisation of the marine mammal Brucella spp. and the change from the band-based approaches to the sequence-based approaches has greatly increased our knowledge about these strains. Several clusters have been identified within the B. ceti and B. pinnipedialis species, and multiple studies have shown that the hooded seal isolates differ from other pinniped isolates. We describe how different molecular methods have contributed to species identification and differentiation of B. ceti and B. pinnipedialis, with special emphasis on the hooded seal isolates. We further discuss the potential role of B. pinnipedialis for the declining Northwest Atlantic hooded seal population. PMID:21819589

A review of Brucella infection in marine mammals, with special emphasis on Brucella pinnipedialis in the hooded seal (Cystophora cristata

Directory of Open Access Journals (Sweden)

Nymo Ingebjørg H

2011-08-01

Full Text Available Abstract Brucella spp. were isolated from marine mammals for the first time in 1994. Two novel species were later included in the genus; Brucella ceti and Brucella pinnipedialis, with cetaceans and seals as their preferred hosts, respectively. Brucella spp. have since been isolated from a variety of marine mammals. Pathological changes, including lesions of the reproductive organs and associated abortions, have only been registered in cetaceans. The zoonotic potential differs among the marine mammal Brucella strains. Many techniques, both classical typing and molecular microbiology, have been utilised for characterisation of the marine mammal Brucella spp. and the change from the band-based approaches to the sequence-based approaches has greatly increased our knowledge about these strains. Several clusters have been identified within the B. ceti and B. pinnipedialis species, and multiple studies have shown that the hooded seal isolates differ from other pinniped isolates. We describe how different molecular methods have contributed to species identification and differentiation of B. ceti and B. pinnipedialis, with special emphasis on the hooded seal isolates. We further discuss the potential role of B. pinnipedialis for the declining Northwest Atlantic hooded seal population.

Harvest-related edge effects on prey availability and foraging of hooded warblers in a bottomland hardwood forest.

Energy Technology Data Exchange (ETDEWEB)

John Kilgo

2005-04-20

The effects of harvest-created canopy gaps in bottomland hardwood forests on arthropod abundance and, hence, the foraging ecology of birds are poorly understood. I predicted that arthropod abundance would be high near edges of group-selection harvest gaps and lower in the surrounding forest, and that male Hooded Warblers (Wilsonia citrina) foraging near gaps would find more prey per unit time than those foraging in the surrounding forest. In fact, arthropod abundance was greater >100 m from a gap edge than at 0-30 m or 30-100 m from an edge, due to their abundance on switchcane (Arundinaria gigantea); arthropods did not differ in abundance among distances from gaps on oaks (Quercus spp.) or red maple (Acer rubrum). Similarly, Hooded Warbler foraging attack rates were not higher near gap edges: when foraging for fledglings, attack rate did not differ among distances from gaps, but when foraging for themselves, attack rates actually were lower 0-30 m from gap edges than 30-100 m or >100 m from a gap edge. Foraging attack rate was positively associated with arthropod abundance. Hooded Warblers apparently encountered fewer prey and presumably foraged less efficiently where arthropods were least abundant, i.e., near gaps. That attack rates among birds foraging for fledglings were not affected by distance from gap (and hence arthropod abundance) suggests that prey availability may not be limiting at any location across the forest, despite the depressing effects of gaps on arthropod abundance.

42 CFR 84.198 - Half-mask facepieces, full facepieces, mouthpieces, hoods, and helmets; fit; minimum requirements.

Science.gov (United States)

2010-10-01

... 42 Public Health 1 2010-10-01 2010-10-01 false Half-mask facepieces, full facepieces, mouthpieces... APPROVAL OF RESPIRATORY PROTECTIVE DEVICES Chemical Cartridge Respirators § 84.198 Half-mask facepieces, full facepieces, mouthpieces, hoods, and helmets; fit; minimum requirements. (a) Half-mask facepieces...

Removal of colour, turbidity, oil and grease for slaughterhouse wastewater using electrocoagulation method

Science.gov (United States)

Yusoff, Mohd Suffian; Azwan, Azlyza Mohd; Zamri, Mohd Faiz Muaz Ahmad; Aziz, Hamidi Abdul

2017-10-01

In this study electrocoagulation method is used to treat slaughterhouse wastewaters. The aim of this study is to determine the efficiency of electrocoagulation method for the removal of colour, turbidity, oil and grease of slaughterhouse wastewaters. The factors of electrode types, and voltage applied during treatment are the study parameters. The types of electrode used are Aluminium (Al) grade 6082 and Iron (Fe) grade 1050. Meanwhile, the ranges of voltage applied are 2, 4, 6, 8 volts at a time interval of 10, 20 and 30 minutes respectively. The effect of these factors on the removal of fat oil and grease (FOG), colour and turbidity are analyzed. The results show maximum removal of FOG, colour and turbidity are recorded using Fe electrode at 8 V of applied voltage with 30 minutes of treatment time. The increase in treatment time of the cell will also increase the amount of hydrogen bubbles at the cathode which results in a greater upwards flux and a faster removal of FOG,, turbidity and colour. The removal of FOG, colour and turbidity are 98%, 92% and 91 % respectively. Meanwhile, by using Al electrodes in the same condition, the removal of FOG, colour and turbidity are 91%, 85% and 87 % respectively. Whereas by using Fe-Al as electrodes pairs, the removal of FOG, colour and turbidity are found to be at 90%, 87% and 76 % respectively. In this case, the Fe-Fe pair electrodes have been proven to provide better performance for FOG, colour and turbidity removals of slaughterhouse wastewaters. Therefore, it is feasible to be considered as an alternative method for wastewater treatment.

Seismicity Induced by Groundwater Recharge at Mt. Hood, Oregon, and its Implications for Hydrogeologic Properties.

Science.gov (United States)

Saar, M. O.; Manga, M.

2002-12-01

Earthquakes induced by human-caused changes in fluid pressure have been documented for many years. Examples include seismicity induced by filling reservoirs and by fluid injection or extraction. Less well-documented are seismic events that potentially are triggered by natural variations in groundwater recharge rates (e.g., Wolf et al., BSSA, 1997; Jimenez and Garcia-Fernandez, JVGR, 2000; Audin et al., GRL, 2002). Large groundwater recharge rates can occur in Volcanic Arcs such as the Oregon Cascades where annual precipitation is > 2 m of which > 50 % infiltrates the ground mostly during snowmelt in spring. As a result, infiltration rates of > 1 m per year concentrated during a few months can occur. Near-surface porosities are about 5-10 %. Thus, groundwater levels may fluctuate annually by about 10-20 m resulting in seasonal pore fluid pressure variations of about 1-2 x 105 Pa. Such large-amplitude, narrow-duration fluid pressure signals may allow investigation of seismicity induced by pore fluid pressure diffusion without the influence of engineered systems such as reservoirs. This kind of in-situ study of natural systems over large representative elementary volumes may allow determination of hydrologic parameters at spatial and temporal scales that are relevant for regional hydrogeology. Furthermore, natural hydrologic triggering of earthquakes that persist for decades provides insight into the state of stress in the crust and suggest long-term near-critical failure conditions. Here, we approximate the temporal variations in groundwater recharge with discharge in runoff-dominated streams at high elevations that show a peak in discharge during snow melt. Seismicity is evaluated as time series of daily number of earthquakes and seismic moments. Both stream discharge and seismicity are compared at equivalent frequency bands by applying segmented least-squares polynomial fits to the data. We find statistically significant correlation between groundwater recharge and

Bonneville - Hood River Vegetation Management Environmental Assessment

Energy Technology Data Exchange (ETDEWEB)

N/A

1998-08-01

To maintain the reliability of its electrical system, BPA, in cooperation with the U.S. Forest Service, needs to expand the range of vegetation management options used to clear unwanted vegetation on about 20 miles of BPA transmission line right-of-way between Bonneville Dam and Hood River; Oregon, within the Columbia Gorge National Scenic Area (NSA). We propose to continue controlling undesirable vegetation using a program of Integrated Vegetation Management (IVM) which includes manual, biological and chemical treatment methods. BPA has prepared an Environmental Assessment (EA) (DOE/EA-1257) evaluating the proposed project. Based on the analysis in the EA, BPA has determined that the proposed action is not a major Federal action significantly affecting the quality of the human environment, within the meaning of the National Environmental Policy Act (NEPA) of 1969. Therefore, the preparation of an Environmental Impact Statement (EIS) is not required and BPA is issuing this FONSI.

Computer modeling of fluid flow and combustion in the ISV [In Situ Vitrification] confinement hood

International Nuclear Information System (INIS)

Johnson, R.W.; Paik, S.

1990-09-01

Safety and suitability objectives for the application of the In Situ Vitrification (ISV) technology at the INEL require that the physical processes involved in ISVV be modeled to determine their operational behavior. The mathematical models that have been determined to address the modeling needs adequately for the ISV analysis package are detailed elsewhere. The present report is concerned with the models required for simulating the reacting flow that occurs in the ISV confinement hood. An experimental code named COYOTE has been secured that appears adequate to model the combustion in the confinement hood. The COYOTE code is a two-dimensional, transient, compressible, Eulerian, gas dynamics code for modeling reactive flows. It recognizes nonuniform Cartesian and cylindrical geometry and is based on the ICE (Implicit Continuous-fluid Eulerian) family of solution methods. It includes models for chemical reactions based on chemical kinetics as well as equilibrium chemistry. The mathematical models contained in COYOTE, their discrete analogs, the solution procedure, code structure and some test problems are presented in the report. 12 refs., 17 figs., 6 tabs

Factors influencing success of metal to plastic conversion programs for under-hood applications

Energy Technology Data Exchange (ETDEWEB)

Male, L.J. [Amoco Chemicals Polymers Business Group, Alpharetta, GA (United States); Desai, K.C.

1995-12-31

This paper compares high performance engineering polymers available today for under-hood applications. It includes an example of an end cap showing value-added capabilities such as design for machining and assembly (DFMA), team approach and computer aided engineering being used for a most cost-effective custom molding solution. These techniques should be part of standard design procedure for conversion programs to cope with the challenges of today and tomorrow. (orig./HW)

Vent hood concept for safely unloading TRUPACT-IIs

International Nuclear Information System (INIS)

Kelley, C.R.

1991-01-01

Receipt of transuranic (TRU) waste in the TRUPACT-2 shipping package, implies a potential of receiving waste packages contaminated with only alpha emitters or emitting hazardous gases. Due to the difficulty of rapidly detecting low-level alpha contamination, a strict contamination control system has been developed to check incoming waste packages in a controlled environment. A part of this control is the use of a vent hood system for the TRUPACT-2 shipping container unloading process. A clear final shroud with a monitored/filtered exhaust system has been designed and fabricated to permit direct surveillance of TRU waste packages prior to exposing personnel or facilities to possible radioactive contamination or hazardous gases. This concept has also been adapted to similar evolutions in which packages are exposed that hold TRU or hazardous materials but cannot be directly monitored prior to opening

Grease Cowboy Fever; or, the making of Johnny T.

Science.gov (United States)

Bradford, K

2002-01-01

Through a mix of theory, memoir and performance narrative, this chapter examines the making of drag persona Johnny T. as part of a king movement where the dominant cultural paradigm of gender is reconsidered and remastered. As seen in Grease, Saturday Night Fever and Urban Cowboy, pop culture icon John Travolta's particular blend of 50s greaser, faggy 70s disco, and 80s country masculinities are shown to be prime drag king conditions, particularly for a dyke who came of age during the 70s Travolta fever. While drawing from personal experience as a king, current trends in the king movement, and gender theory, this essay calls into question the lines between performing masculinity on and off the stage, inviting us to see both the work and play, the parody and realness, the struggle and liberation that make up the transgressive world of drag kinging and gender variance. Drawing upon gender theorists Judith Butler and Judith Halberstam, gender is exposed as a social construction both produced and performed, and as such, drag kinging is framed as an arena where gender is reconfigured.

Pre-migratory congregations of Red-crowned (Grus japonensis, White-naped (G. vipio and Hooded (G. monacha cranes in the Muraviovka Park for Sustainable Land Use in 1992

Directory of Open Access Journals (Sweden)

P. I. Gorlov

2017-05-01

Full Text Available The autumn pre-migratory concentrations of Red-crowned, White-naped and Hooded Cranes were studied in the Muraviovka Park for Sustainable Land Use and Environmentla Education (Tambov District, Amur Region, Russian Federation during 23.08–29.09.1992. We counted 292 Hooded Cranes, 34 White-naped Cranes, and 17 Red-crowned Cranes during the study period. We also marked specific differences in the behaviour of the birds connected with their readiness for migration. The Hooded Cranes showed the greatest readiness for migration. We observed mutual flights, overnight stays, and feeding of adult birds and family groups in their flocks. This was not the same in the flocks of White-naped Cranes. However, the average number of birds in the flocks of White-naped Cranes had increased by the end of our observations due to new families joining the general flock. The family parties of the Red-crowned Crane and adult birds without young individuals stayed apart from each other and from other crane species during the whole observation period. We registered the autumn departure of Hooded Cranes in late September, the migratory departure of White-naped Cranes in the middle of October, and the Red-crowned Cranes left the area in the first half of November. The breeding period for all crane species starts at the same time: the third decade of April – the beginning of May. The young of the studied crane species differ significantly in the period of time before fledging: Hooded Cranes – 55–60 days, White-naped Cranes – 65–70 days, and Red-crowned Cranes – 70–75 days because of their specific differences in the ratio of size to weight (1 : 1.3 : 1.7. Thus, the time difference between the Hooded and Red-crowned Cranes is about 2–3 weeks. We suggest that this is the main reason that determines the differences between these species in the timing of the the start of autumn migration.

SPECIFIC FEATURES OF TECHNOLOGY OF MANUFACTURING A ZINC-COATED TUB WIRE FOR MUZZLE (BOTTLE’ HOOD WIRE

Directory of Open Access Journals (Sweden)

D. B. Zuev

2016-01-01

Full Text Available The paper presents the main technical specifications of galvanized low carbon wire for muzzles (bottle’hood wire, consistent with the exploitation requirements to the wire in the manufacture and use of muzzles. The main criteria when selecting the steel grade and upon selection of the technological processes are given. 

Estimates of Nutrient Loading by Ground-Water Discharge into the Lynch Cove Area of Hood Canal, Washington

Science.gov (United States)

Simonds, F. William; Swarzenski, Peter W.; Rosenberry, Donald O.; Reich, Christopher D.; Paulson, Anthony J.

2008-01-01

Low dissolved oxygen concentrations in the waters of Hood Canal threaten marine life in late summer and early autumn. Oxygen depletion in the deep layers and landward reaches of the canal is caused by decomposition of excess phytoplankton biomass, which feeds on nutrients (primarily nitrogen compounds) that enter the canal from various sources, along with stratification of the water column that prevents mixing and replenishment of oxygen. Although seawater entering the canal is the largest source of nitrogen, ground-water discharge to the canal also contributes significant quantities, particularly during summer months when phytoplankton growth is most sensitive to nutrient availability. Quantifying ground-water derived nutrient loads entering an ecologically sensitive system such as Hood Canal is a critical component of constraining the total nutrient budget and ultimately implementing effective management strategies to reduce impacts of eutrophication. The amount of nutrients entering Hood Canal from ground water was estimated using traditional and indirect measurements of ground-water discharge, and analysis of nutrient concentrations. Ground-water discharge to Hood Canal is variable in space and time because of local geology, variable hydraulic gradients in the ground-water system adjacent to the shoreline, and a large tidal range of 3 to 5 meters. Intensive studies of ground-water seepage and hydraulic-head gradients in the shallow, nearshore areas were used to quantify the freshwater component of submarine ground-water discharge (SGD), whereas indirect methods using radon and radium geochemical tracers helped quantify total SGD and recirculated seawater. In areas with confirmed ground-water discharge, shore-perpendicular electrical resistivity profiles, continuous electromagnetic seepage-meter measurements, and continuous radon measurements were used to visualize temporal variations in ground-water discharge over several tidal cycles. The results of these

Harvest-related edge effects on prey availability and foraging of hooded warblers in a bottomland hardwood forest

Science.gov (United States)

John C. Kilgo

2005-01-01

The effects of harvest-created canopy gaps in bottomland hardwood forests on arthropod abundance and, hence, the foraging ecology of birds are poorly understood. I predicted that arthropod abundance would be high near edges of group-selection harvest gaps and lower in the surrounding forest, and that male Hooded Warblers (Wilsonia citrina) foraging...

The indigenisation of Lubriplate 630-2 and development of Servo-Nuclease-2 grease for the fuelling machine of pressurised heavy water power reactors

International Nuclear Information System (INIS)

Srivastava, S.B.; Thomas, V.G.

1980-01-01

A new grease of NLGI-2 consistency was developed for application in nuclear environments. The evaluation consisted of both static tests employing a cobalt-60 γ-ray source and dynamic tests carried out on specially designed rigs in Fuelling Machine Vaults of RAPS. (auth.)

Hood of the truck statistics for food animal practitioners.

Science.gov (United States)

Slenning, Barrett D

2006-03-01

This article offers some tips on working with statistics and develops four relatively simple procedures to deal with most kinds of data with which veterinarians work. The criterion for a procedure to be a "Hood of the Truck Statistics" (HOT Stats) technique is that it must be simple enough to be done with pencil, paper, and a calculator. The goal of HOT Stats is to have the tools available to run quick analyses in only a few minutes so that decisions can be made in a timely fashion. The discipline allows us to move away from the all-too-common guess work about effects and differences we perceive following a change in treatment or management. The techniques allow us to move toward making more defensible, credible, and more quantifiably "risk-aware" real-time recommendations to our clients.

Isolation of Bacterial Strain for Biodegradation of Fats, Oil and Grease

International Nuclear Information System (INIS)

Alkhatib, M.F.; Mohd Zahangir Alam; Shabana, H.F.M.

2015-01-01

Fat, oil and grease (FOG) deposition is one of the major problems that harm the environment and cause dissatisfaction for human. Uncontrolled and un-pre-treated FOG removal from the kitchen could lead to its accumulation in the piping system. Problems include the interference of fat with the aerobic microorganisms that are responsible in treating the wastewater by reducing oxygen transfer rates and for anaerobic microorganisms; their efficiency could also be reduced due to the reduction of the transport of soluble substrates to the bacterial biomass. Biodegradation could be one of the effective means to treat FOG. The main objective of this study is to isolate bacterial strains from the FOG waste and identify the strains that are capable in biodegrading FOG waste. FOG sample was collected from a sewer manhole. Enrichment technique was applied, followed by isolation of bacterial strains to determine which strain is able to degrade the FOG deposition. Some morphology for the bacterial strain was done to determine its characteristics. (author)

Sand or grease? Corruption-institutional trust nexus in post-Soviet countries

Directory of Open Access Journals (Sweden)

Nazim Habibov

2017-07-01

Full Text Available This paper empirically tests several hypotheses about the nexus of corruption-institutional trust in Post-Soviet transitional countries of the former Soviet Union and Mongolia. We use two different indices of institutional trust to check the robustness of our analysis and estimate OLS and instrumental variable models with and without interaction terms. All things considered, our findings reject “greases the wheels” and “trust begets an honest political system” hypotheses. Instead, our findings support the “sand the wheels” hypothesis. Furthermore, a multiplicative interaction model suggests that the negative marginal effects of experienced corruption are higher in the environments where satisfaction with services is low. In addition, we found that increases in corruption erode trust at all levels of the societal institutions including political parties, government and financial institutions, international investors, non-profit organizations, and trade unions. This finding is important since it highlights the negative consequences of corruption on the development of broader level economic institutions and on civil society.

Locating inputs of freshwater to Lynch Cove, Hood Canal, Washington, using aerial infrared photography

Science.gov (United States)

Sheibley, Rich W.; Josberger, Edward G.; Chickadel, Chris

2010-01-01

The input of freshwater and associated nutrients into Lynch Cove and lower Hood Canal (fig. 1) from sources such as groundwater seeps, small streams, and ephemeral creeks may play a major role in the nutrient loading and hydrodynamics of this low dissolved-oxygen (hypoxic) system. These disbursed sources exhibit a high degree of spatial variability. However, few in-situ measurements of groundwater seepage rates and nutrient concentrations are available and thus may not represent adequately the large spatial variability of groundwater discharge in the area. As a result, our understanding of these processes and their effect on hypoxic conditions in Hood Canal is limited. To determine the spatial variability and relative intensity of these sources, the U.S. Geological Survey Washington Water Science Center collaborated with the University of Washington Applied Physics Laboratory to obtain thermal infrared (TIR) images of the nearshore and intertidal regions of Lynch Cove at or near low tide. In the summer, cool freshwater discharges from seeps and streams, flows across the exposed, sun-warmed beach, and out on the warm surface of the marine water. These temperature differences are readily apparent in aerial thermal infrared imagery that we acquired during the summers of 2008 and 2009. When combined with co-incident video camera images, these temperature differences allow identification of the location, the type, and the relative intensity of the sources.

Nocturnal feeding under artificial light conditions by Brown-hooded Gull (Larus maculipennis) in Puerto Madryn harbour (Chubut Province, Argentina)

NARCIS (Netherlands)

Leopold, M.F.; Philippart, C.J.M.; Yorio, P.

2010-01-01

This paper describes nocturnal, marine feeding behaviour in the Brown-hooded Gull (Larus maculipennis) in November 2009. The gulls assembled at night at the end of a long pier, running 800 m offshore into the Golfo Nuevo, at Puerto Madryn, Chubut Province, Argentina. Powerful lights predictably

A Survey on the Removal Efficiency of Fat, Oil and Grease in Shiraz Municipal Wastewater Treatment Plant

Directory of Open Access Journals (Sweden)

Dehghani

2014-12-01

Full Text Available Background Fat, oil and grease (FOG in municipal wastewater treatment plant (MWWTP caused many problems. Objectives This study aimed to determine the removal efficiency of FOG in Shiraz MWWTP. Materials and Methods The removal efficiencies of FOG in the MWWTP were studied from June 2011 to September 2011 in Shiraz (Iran. The influent and effluent wastewater samples were collected in a volume of one liter (4 samples per week and analyzed according to the standard methods. Samples are transferred to the laboratory immediately. The concentration of FOG was determined using the solvent extraction and separating funnel and then compared with the effluent standards. To analyze the data, SPSS (version 11.5, Chi-square test and t test were used. Results The results showed that the FOG amount in input raw sewage in the MWWTP from June 2011 to September 2011 was around 25.5 mg/L and the amount in treated wastewater was about 8.1 mg/L. The FOG removal efficiency in this refinery was about 70% and met the environmental standards for the discharge (less than 10 mg/L (P < 0.05. Conclusions The effluent can be discharged to surface waters or used for irrigation. In order to the FOG concentration met the effluent standards, it is very crucial to control the entrance of industrial wastewater to the municipal wastewater collection networks. Otherwise, the MWWTP should be upgraded and the special techniques used to reduce FOG.

Problems, control, and treatment of fat, oil, and grease (FOG): a review.

Science.gov (United States)

Husain, Iman A F; Alkhatib, Ma'an Fahmi; Jammi, Mohamed Saedi; Mirghani, Mohamed E S; Bin Zainudin, Zaki; Hoda, Asif

2014-01-01

Presence of fat, oil, and grease (FOG) in wastewater is an ever-growing concern to municipalities and solid-waste facility operators. FOG enters the sewer system from restaurants, residences, and industrial food facilities. Its release into the sewer system results in a continuous build-up that causes eventual blockage of sewer pipes. Several researchers have investigated FOG deposition based on the local conditions of sewers and lifestyle. This paper attempts to review the physical and chemical characteristics of FOG, sources of FOG, and potential chemical and biological reactions of FOG. The effect of the aforementioned factors on the FOG-deposition mechanism is also discussed. Moreover, insight into the current control and treatment methods and potential reuse of FOG is highlighted. It is expected that this review would provide scientists and the concerned authorities a holistic view of the recent researches on FOG control, treatment, and reuse.

High-purity fatty acid methyl ester production from canola, soybean, palm, and yellow grease lipids by means of a membrane reactor

International Nuclear Information System (INIS)

Cao Peigang; Dube, Marc A.; Tremblay, Andre Y.

2008-01-01

High-purity fatty acid methyl ester (FAME) was produced from different lipids, such as soybean oil, canola oil, a hydrogenated palm oil/palm oil blend, yellow grease, and brown grease, combined with methanol using a continuous membrane reactor. The membrane reactor combines reaction and separation in a single unit, provides continuous mixing of raw materials, and maintains a high molar ratio of methanol to lipid in the reaction loop while maintaining two phases during the reaction. It was demonstrated that the membrane reactor can be operated using a very broad range of feedstocks at highly similar operating conditions to produce FAME. The total glycerine and free glycerine contents of the FAME produced were below the ASTM D6751 standard after a single reaction step. Under essentially the same reaction conditions, a conventional batch reaction was not able to achieve the same degree of FAME purity. The effect of the fatty acid composition of the lipid feedstocks on the FAME purity was also shown. It was demonstrated that, due to the fatty acid composition, FAME from virgin soybean oil and virgin canola oil was produced in the membrane reactor within ASTM specifications even without a water washing step

Utilisation of polyurethane composit with 50% composition of roystonea regia fiber as noise reduction panel on car hood

Science.gov (United States)

Ikhwansyah; Mulia; Gunawan, S.; Lubis, R. D. W.

2018-02-01

The objective is to get the characteristics of noise reduction, noise reduction level, variety of measurement spaces, and knowing the process in making acoustic material of natural fiber becomes noise reduction on a car hood. The process of making noise reduction material used casting method and pressed by using molded press. The composition of noise reduction material consist of 50% roystonea regia by 32 mesh and 50% combined by gypsum and polyurethane. The result shows that the average result of noise reduction at X1- side is 5,7% and X2- side is 3,9%, X1+ side is 0,9% and X2+ side is 6,2%, Z1- side is 8,9% and Z2- side is 10,1%, Z1+ side is 9,7% and Z2+ side is 10,01%. The main conclusion of the study shows that a noise reduction which made of roystonea regia with 32 mesh mixed by matrix of polyurethane and gypsum is appropriate for noise reduction on car hood.

The Robin Hood method - A novel numerical method for electrostatic problems based on a non-local charge transfer

International Nuclear Information System (INIS)

Lazic, Predrag; Stefancic, Hrvoje; Abraham, Hrvoje

2006-01-01

We introduce a novel numerical method, named the Robin Hood method, of solving electrostatic problems. The approach of the method is closest to the boundary element methods, although significant conceptual differences exist with respect to this class of methods. The method achieves equipotentiality of conducting surfaces by iterative non-local charge transfer. For each of the conducting surfaces, non-local charge transfers are performed between surface elements, which differ the most from the targeted equipotentiality of the surface. The method is tested against analytical solutions and its wide range of application is demonstrated. The method has appealing technical characteristics. For the problem with N surface elements, the computational complexity of the method essentially scales with N α , where α < 2, the required computer memory scales with N, while the error of the potential decreases exponentially with the number of iterations for many orders of magnitude of the error, without the presence of the Critical Slowing Down. The Robin Hood method could prove useful in other classical or even quantum problems. Some future development ideas for possible applications outside electrostatics are addressed

Oil and grease (O&G) removal from commercial kitchen waste water using carbonised grass as a key media

OpenAIRE

Rahmat Siti Nazahiyah; Mohd Ali Ahmad Zurisman; Wan Ibrahim Mohd Haziman; Alias Nur Azrena

2017-01-01

Oil and grease (O&G) are usually found in kitchen waste water. O&G are poorly soluble in water and can cause serious problems during the wastewater treatment. Adsorption is a fundamental process in the treatment of kitchen waste water and very economical. Activated carbon is the most effective adsorbent for this application. Therefore, the aim of the current study is to determine the potential of four materials (i.e. sand, gravel, carbonised grass (CG) and clay powder) as filter media for O&G...

Addendum 4 to CSAR 81-001, Installation of an Official Critical Drain on the Plexiglass Contamination Barrier in HC-227T Hood

International Nuclear Information System (INIS)

Chiao, T.

1995-12-01

This report defines the maximum space allowed between the floor surface and the lower edge of an official criticality drain which is to be installed on the plexiglas contamination barrier in HC-227T Hood

Identification of a Major Locus Contributing to Erythrocyte 2,3-Diphosphoglycerate Variability in Hooded (Long-Evans) Rats

Science.gov (United States)

Noble, N. A.; Brewer, G. J.

1977-01-01

The erythrocyte glycolytic intermediate 2,3-diphosphoglycerate (DPG) and adenosine triphosphate (ATP) play an important role in oxygen transport and delivery by binding to hemoglobin (Hb) and reducing its affinity for oxygen. Considerable quantitative variability in the levels of DPG and ATP exists in human populations and in a population of hooded (Long-Evans) rats we have studied. This paper presents the results of studies on the genetic component of DPG-level variation in an outbred population of hooded rats. Beginning with about 100 rats, a two-way selection experiment was initiated. Pairs of rats with the highest DPG levels were mated to produce a High-DPG rat strain and animals with the lowest DPG levels were mated to produce a Low-DPG strain. Mean DPG levels responded rapidly to selection and, from generation 3 on, the differences between strain means were highly significant. Ten High-DPG strain rats were intercrossed with 10 Low-DPG strain rats of generation 10 to produce an F1 generation in which the DPG levels were almost as high as those of High-DPG animals. This indicates partial dominance of High-DPG alleles. The F2 DPG-level distribution showed two distinct subpopulations. The high DPG subpopulation contained three times as many animals as the low DPG subpopulation. From these results and the statistical analyses performed, it was concluded that the DPG differences between strains were due to an allelic difference at one major locus, the allele carried by the High-DPG strain showing partial dominance over the allele carried by the Low-DPG strain. It appears that this locus may also effect ATP levels to a large extent and is polymorphic in hooded rat populations. Identification of this locus gives us a useful tool for studies of the physiological effects of DPG variability, as well as providing an example of a major gene effect in a quantitatively varying trait. PMID:863239

Biological Assessment of the Effects of Military Associated Activities on Endangered Species at Fort Hood, Texas

Science.gov (United States)

1992-12-01

monographing the genus Croton. Dr. Joe Allen Farmer published a dissertation on the species in 1962. Studies on the Fort Hood population have begun under...Woodhouse, S.W., "Descriptions of New Species of the Genus Vireo, VieilL, and Zonorrichia, Swains," Proceeding of the Academy of Natural Sciences of...sinuata Skunkbush Saumac Rhus aroma tica Texas Oak Quercus texazza Texas Persimmon, Diospyros texana Texas Ashe Fraxinus texensis Virginia Creeper Paz

76 FR 42502 - Substantial Product Hazard List: Children's Upper Outerwear in Sizes 2T to 12 With Neck or Hood...

Science.gov (United States)

2011-07-19

... because children of those ages are most at risk. 4. Adult Apparel and Marketing Concerns (Comment 4)--Two... smaller adult sizes and larger children's sizes. Further, children at the pre-teen and teen stages often... channel, and the commenters raised concerns about the 2009 recall of children's hooded sweatshirts with...

Research on extraction of lithium from dilute solution

International Nuclear Information System (INIS)

Takeuchi, Takeji

1983-01-01

Lithium has been used as the refrigerant for air conditioning, the additive for aluminum refining and catalyzer and for high performance grease and small batteries so far. The demand in these existing uses has grown on the average 8.8 % yearly, accordingly the cumulative consumption is estimated to be 0.8 x 10 9 kg by 2000. It is expected that the lithium resources of 1 x 10 9 kg available by 2000 will be used up before the practical use of fusion reactors. Lithium is indispensable for generating tritium in fusion reactors. The lithium concentration in sea water is as thin as 0.2 g/m 3 , therefore it is necessary to develop the method of effectively extracting lithium from a large quantity of sea water. As one of the methods, it was found that the corrosion product of metallic aluminum was able to be utilized. Namely, when metallic aluminum such as foils is immersed in sea water, the corrosion product adheres on the surface, and this corrosion product extracts lithium by cation exchange process preferentially. In this method, the process of making an extracting agent is not necessary, and it is also unnecessary to control the condition of sea water. (Kako, I.)

Removal of petroleum-derived hydrocarbons from contaminated soils by solvent extraction

International Nuclear Information System (INIS)

Ladanowski, C.; Petti, L.

1993-01-01

Laboratory studies were conducted using hexane for the removal of light crude oil from contaminated sand, peat, and clay soils. The bench-scale process tested consists of three major steps: solvent washing, settling/decantation/filtration of extract, and solvent recycle. The results indicate that the use of solvent extraction for cleanup of oil-contaminated soils is an effective technology at the bench-scale level. Using a 1,000 g batch system, extremely high oil removal efficiencies were obtained from contaminated sand (up to 98.9%) and peat soil (up to 83.9%). The final oil contaminant concentration for sand varied between 0.06% and 0.39%, while that for peat soil varied between 1.52% and 5.21%. The guidelines for the decommissioning and cleanup of sites in Ontario for oil and grease (1 wt %) were met in all instances for the treated sand. Hexane recovery from diesel-contaminated sand and peat soil experiments was ca 81% and 67% respectively. 4 refs., 6 figs., 10 tabs

Microbiological and serological monitoring in hooded crow (Corvus corone cornix in the Region Lombardia, Italy

Directory of Open Access Journals (Sweden)

Guido Grilli

2010-01-01

Full Text Available The health status of 276 hooded crows (Corvus corone cornix from various provinces of Lombardy was monitored for three years. Bacteriological examination detected E. coli (76%, Campylobacter jejuni (17%, Salmonella typhimurium (11.6%, Yersinia spp. (6.5%, Clamydophila abortus and C. psittaci (2.6%; from six birds showing severe prostration Pasteurella multocida was isolated. Virological and serological tests were negative for Avian Influenza virus (AIV, West Nile virus (WNV and only three samples were positive for Newcastle disease virus (NDV but only at serology (titre 1:16.

Owning the Journey: Using Collaborative Revisions of Little Red Riding Hood in Teaching Introduction to Literature at a Historically Black University

Science.gov (United States)

Scott, Pauline

2012-01-01

Design and implementation of a collaborative course project, using Little Red Riding Hood (LRRH) to teach and discuss the concepts of orality, cultural legacy, archetypes, adaptation/appropriation, and social criticism in an Introduction to Literature course at Historically Black Alabama State University in Montgomery, Alabama. The student groups…

Evidence for fat, oil, and grease (FOG) deposit formation mechanisms in sewer lines.

Science.gov (United States)

He, Xia; Iasmin, Mahbuba; Dean, Lisa O; Lappi, Simon E; Ducoste, Joel J; de los Reyes, Francis L

2011-05-15

The presence of hardened and insoluble fats, oil, and grease (FOG) deposits in sewer lines is a major cause of line blockages leading to sanitary sewer overflows (SSOs). Despite the central role that FOG deposits play in SSOs, little is known about the mechanisms of FOG deposit formation in sanitary sewers. In this study, FOG deposits were formed under laboratory conditions from the reaction between free fatty acids and calcium chloride. The calcium and fatty acid profile analysis showed that the laboratory-produced FOG deposit displayed similar characteristics to FOG deposits collected from sanitary sewer lines. Results of FTIR analysis showed that the FOG deposits are metallic salts of fatty acid as revealed by comparisons with FOG deposits collected from sewer lines and pure calcium soaps. Based on the data, we propose that the formation of FOG deposits occurs from the aggregation of excess calcium compressing the double layer of free fatty acid micelles and a saponification reaction between aggregated calcium and free fatty acids.

Levels of Petroleum Hydrocarbons and some Heavy Metals in ...

African Journals Online (AJOL)

Michael Horsfall

has outlets to the Atlantic Ocean. The river which supports major commercial ... acidification. Oils and solids or viscous grease present were separated from liquid samples by filtration. After extraction, the residue after solvent evaporation was weighed to determine the oil and grease content. Compounds volatilized at or ...

Data from moored current meters, temperature and salinity from a historical mooring placed in Hood Canal, Puget Sound, February - April 1980 (NODC Accession 0000680)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Physical, current, and other data were collected from moored buoys in Hood Canal and the Puget Sound from 08 February 1980 to 10 April 1980. Data were collected by...

Environmental Assessment for Ongoing and Future Operations at U.S. Navy Dabob Bay and Hood Canal Military Operating Areas

Science.gov (United States)

2002-05-01

well as being cultivated in aquaculture operations in Puget Sound, including Hood Canal and Dabob Bay (Figure 3.4-2). Pacific oysters (Crassostrea...gigas) are widely cultivated in aquaculture operations in Puget Sound. Commercial oyster beds exist in Dabob Bay, mostly at the north end. Dabob Bay... Ecotoxicology of metals in aquatic sediments: binding and release, bioavailability, risk assessment, and remediation. Canadian Journal of

Vigilance and activity time-budget adjustments of wintering hooded cranes, Grus monacha, in human-dominated foraging habitats.

Science.gov (United States)

Li, Chunlin; Zhou, Lizhi; Xu, Li; Zhao, Niannian; Beauchamp, Guy

2015-01-01

Due to loss and degradation of natural wetlands, waterbirds increasingly rely on surrounding human-dominated habitats to obtain food. Quantifying vigilance patterns, investigating the trade-off among various activities, and examining the underlying mechanisms will help us understand how waterbirds adapt to human-caused disturbances. During two successive winters (November-February of 2012-13 and 2013-14), we studied the hooded crane, Grus monacha, in the Shengjin Lake National Nature Reserve (NNR), China, to investigate how the species responds to human disturbances through vigilance and activity time-budget adjustments. Our results showed striking differences in the behavior of the cranes when foraging in the highly disturbed rice paddy fields found in the buffer zone compared with the degraded natural wetlands in the core area of the NNR. Time spent vigilant decreased with flock size and cranes spent more time vigilant in the human-dominated buffer zone. In the rice paddy fields, the birds were more vigilant but also fed more at the expense of locomotion and maintenance activities. Adult cranes spent more time vigilant and foraged less than juveniles. We recommend habitat recovery in natural wetlands and community co-management in the surrounding human-dominated landscape for conservation of the hooded crane and, generally, for the vast numbers of migratory waterbirds wintering in the middle and lower reaches of the Yangtze River floodplain.

Quantifying fat, oil, and grease deposit formation kinetics.

Science.gov (United States)

Iasmin, Mahbuba; Dean, Lisa O; Ducoste, Joel J

2016-01-01

Fat, oil, and grease (FOG) deposits formed in sanitary sewers are calcium-based saponified solids that are responsible for a significant number of nationwide sanitary sewer overflows (SSOs) across United States. In the current study, the kinetics of lab-based saponified solids were determined to understand the kinetics of FOG deposit formation in sewers for two types of fat (Canola and Beef Tallow) and two types of calcium sources (calcium chloride and calcium sulfate) under three pH (7 ± 0.5, 10 ± 0.5, and ≈14) and two temperature conditions (22 ± 0.5 and 45 ± 0.5 °C). The results of this study displayed quick reactions of a fraction of fats with calcium ions to form calcium based saponified solids. Results further showed that increased palmitic fatty acid content in source fats, the magnitude of the pH, and temperature significantly affect the FOG deposit formation and saponification rates. The experimental data of the kinetics were compared with two empirical models: a) Cotte saponification model and b) Foubert crystallization model and a mass-action based mechanistic model that included alkali driven hydrolysis of triglycerides. Results showed that the mass action based mechanistic model was able to predict changes in the rate of formation of saponified solids under the different experimental conditions compared to both empirical models. The mass-action based saponification model also revealed that the hydrolysis of Beef Tallow was slower compared to liquid Canola fat resulting in smaller quantities of saponified solids. This mechanistic saponification model, with its ability to track the saponified solids chemical precursors, may provide an initial framework to predict the spatial formation of FOG deposits in municipal sewers using system wide sewer collection modeling software. Copyright © 2015 Elsevier Ltd. All rights reserved.

78 FR 14457 - Guidelines Establishing Test Procedures for the Analysis of Pollutants Under the Clean Water Act...

Science.gov (United States)

2013-03-06

... discharge limits. Method 1664A is a liquid/liquid extraction (LLE), gravimetric procedure that employs...: EPA discussed, but did not propose, a new method, ASTM D7575, for oil and grease in the 2010 proposed Methods Update Rule (MUR). Oil and grease is a method-defined parameter. That is, the nature and amount of...

A Comparative Morphometric Analysis of Three Cranial Nerves in Two Phocids: The Hooded Seal (Cystophora cristata) and the Harbor Seal (Phoca vitulina).

Science.gov (United States)

Wohlert, Dennis; Kröger, Jürgen; Witt, Martin; Schmitt, Oliver; Wree, Andreas; Czech-Damal, Nicole; Siebert, Ursula; Folkow, Lars; Hanke, Frederike D

2016-03-01

While our knowledge about the senses of pinnipeds has increased over the last decades almost nothing is known about the organization of the neuroanatomical pathways. In a first approach to this field of research, we assessed the total number of myelinated axons of three cranial nerves (CNs) in the harbor (Phoca vitulina, Pv) and hooded seal (Cystophora cristata, Cc). Axons were counted in semithin sections of the nerves embedded in Epon and stained with toluidine blue. In both species, the highest axon number was found within the optic nerve (Pv 187,000 ± 8,000 axons, Cc 481,600 ± 1,300 axons). Generally, considering absolute axon numbers, far more axons were counted within the optic and trigmenial nerve (Pv 136,700 ± 2,500 axons, Cc 179,300 ± 6,900 axons) in hooded in comparison to harbor seals. The axon counts of the vestibulocochlear nerve are nearly identical for both species (Pv 87,100 ± 8,100 axons, Cc 86,600 ± 2,700 axons). However, when comparing cell density, the cell density is almost equal for all nerves for both species except for the optic nerve in which cell density was particularly higher than in the other nerves and higher in hooded in comparison to harbor seals. We here present the first comparative analysis of three CNs in two phocid seals. While the CNs of these closely related species share some general characteristics, pronounced differences in axon numbers/densities are apparent. These differences seem to reflect differences in e.g. size, habitat, and/or functional significance of the innervated sensory systems. © 2015 Wiley Periodicals, Inc.

Development of Extraction Methods for the Analysis of Perfluorinated Compounds in Leather with High Performance Liquid Chromatography Tandem Mass Spectrometry

Science.gov (United States)

Zhang, Yan; Wang, Youchao; Tang, Chuanjiang; Nie, Jingmei; Xu, Chengtao

2018-01-01

Perfluorinated compounds (PFCs), used to provide water, oil, grease, heat and stain repellency to a range of textile and other products, have been found to be persistent in the environment and are associated with adverse effects on humans and wildlife. This study presents the development and validation of an analytical method to determine the simultaneous presence of eleven PFCs in leather using solid-phase extraction followed by liquid chromatography-tandem mass spectrometry (LC-MS/MS). The perfluorinated compounds were primarily extracted from the samples by a liquid extraction procedure by ultrasonic, in which the parameters were optimized. Then the solid-phase extraction (SPE) is the most important advantages of the developed methodology. The sample volume and elution conditions were optimized by means of an experimental design. The proposed method was applied to determine the PFCs in leather, where the detection limits of the eleven compounds were 0.09-0.96 ng/L, and the recoveries of all compounds spiked at 5 ng/L concentration level were in the range of 65-96%, with a better RSD lower than 19% (n = 7).

Hydrothermal synthesis of copper zirconium phosphate hydrate [Cu(OH)2Zr(HPO4)2·2H2O] and an investigation of its lubrication properties in grease.

Science.gov (United States)

Zhang, Xiaosheng; Xu, Hong; Zuo, Zhijun; Lin, Zhi; Ferdov, Stanislav; Dong, Jinxiang

2013-08-28

Copper zirconium phosphate hydrate (Cu(OH)2Zr(HPO4)2·2H2O, hereafter referred to as Cu-α-ZrP) with high crystallinity was directly synthesized in a NaF-CuO-ZrO-P2O5-H2O system under hydrothermal conditions. The copper ion was confirmed to be an exchangeable cation in the Cu-α-ZrP through elemental analysis and a proton ion exchange process. The crystal structure of the Cu-α-ZrP was determined ab initio by using X-ray powder diffraction data. In the structure, the CuO6 octahedron would be located in an exchangeable atom position. Moreover, Cu-α-ZrP was evaluated as an additive in grease in a four ball test. The maximum nonseizure load (PB, representing the load-carrying capacity) of the base grease containing Cu-α-ZrP was increased from 353 to 1235 N. The excellent load-carrying capacity may be explained by the easier adherence of the material to the worn surface forming a tight protective film.

Optimization of municipal sludge and grease co-digestion using disintegration technologies.

Science.gov (United States)

Bouchy, L; Pérez, A; Camacho, P; Rubio, P; Silvestre, G; Fernández, B; Cano, R; Polanco, M; Díaz, N

2012-01-01

Many drivers tend to foster the development of renewable energy production in wastewater treatment plants as many expectations rely upon energy recovery from sewage sludge, for example through biogas use. This paper is focused on the assessment of grease waste (GW) as an adequate substrate for co-digestion with municipal sludge, as it has a methane potential of 479-710 LCH(4)/kg VS, as well as the evaluation of disintegration technologies as a method to optimize the co-digestion process. With this objective three different pre-treatments have been selected for evaluation: thermal hydrolysis, ultrasound and enzymatic treatment. Results have shown that co-digestion processes without pre-treatment had a maximum increment of 128% of the volumetric methane productivity when GW addition was 23% inlet (at 20 days of HRT and with an OLR of 3.0 kg COD/m(3)d), compared with conventional digestion of sewage sludge alone. Concerning the application of the selected disintegration technologies, all pre-treatments showed improvements in terms of methane yield (51.8, 89.5 and 57.6% more for thermal hydrolysis, ultrasound and enzymatic treatment, respectively, compared with non-pretreated wastes), thermal hydrolysis of GW and secondary sludge being the best configuration as it improved the solubilization of the organic matter and the hydrodynamic characteristics of digestates.

Wear of Spur Gears Having a Dithering Motion and Lubricated with a Perfluorinated Polyether Grease

Science.gov (United States)

Krantz, Timothy; Oswald, Fred; Handschuh, Robert

2007-01-01

Gear contact surface wear is one of the important failure modes for gear systems. Dedicated experiments are required to enable precise evaluations of gear wear for a particular application. The application of interest for this study required evaluation of wear of gears lubricated with a grade 2 perfluorinated polyether grease and having a dithering (rotation reversal) motion. Experiments were conducted using spur gears made from AISI 9310 steel. Wear was measured using a profilometer at test intervals encompassing 10,000 to 80,000 cycles of dithering motion. The test load level was 1.1 GPa maximum Hertz contact stress at the pitch-line. The trend of total wear as a function of test cycles was linear, and the wear depth rate was approximately 1.2 nm maximum wear depth per gear dithering cycle. The observed wear rate was about 600 times greater than the wear rate for the same gears operated at high speed and lubricated with oil.

Mechanisms of fat, oil and grease (FOG) deposit formation in sewer lines.

Science.gov (United States)

He, Xia; de los Reyes, Francis L; Leming, Michael L; Dean, Lisa O; Lappi, Simon E; Ducoste, Joel J

2013-09-01

FOG deposits in sewer systems have recently been shown to be metallic salts of fatty acids. However, the fate and transport of FOG deposit reactant constituents and the complex interactions during the FOG deposit formation process are still largely unknown. In this study, batch tests were performed to elucidate the mechanisms of FOG deposit formation that lead to sanitary sewer overflows (SSOs). We report the first formation of FOG deposits on a concrete surface under laboratory conditions that mimic the formation of deposits in sewer systems. Results showed that calcium, the dominant metal in FOG deposits, can be released from concrete surfaces under low pH conditions and contribute to the formation process. Small amounts of additional oil to grease interceptor effluent substantially facilitated the air/water or pipe surface/water interfacial reaction between free fatty acids and calcium to produce surface FOG deposits. Tests of different fatty acids revealed that more viscous FOG deposit solids were formed on concrete surfaces, and concrete corrosion was accelerated, in the presence of unsaturated FFAs versus saturated FFAs. Based on all the data, a comprehensive model was proposed for the mechanisms of FOG deposit formation in sewer systems. Copyright © 2013 Elsevier Ltd. All rights reserved.

Hooded seal Cystophora cristata foraging areas in the Northeast Atlantic Ocean-Investigated using three complementary methods.

Directory of Open Access Journals (Sweden)

Jade Vacquie-Garcia

Full Text Available Identifying environmental characteristics that define the ecological niche of a species is essential to understanding how changes in physical conditions might affect its distribution and other aspects of its ecology. The present study used satellite relay data loggers (SRDLs to study habitat use by Northeast Atlantic hooded seals (N = 20; 9 adult females, 3 adult males, and 8 juveniles. Three different methods were used in combination to achieve maximum insight regarding key foraging areas for hooded seals in this region, which have decline by 85% in recent decades: 1 first passage time (FPT; 2 vertical transit rate and; 3 change in dive drift rate. Generalized additive mixed models (GAMM were applied to each method to determine whether specific habitat characteristics were associated with foraging. Separate models were run for the post-molting and the post-breeding seasons; sex and age classes were included in the GAMMs. All three methods highlighted a few common geographic areas as being important foraging zones; however, there were also some different areas identified by the different methods, which highlights the importance of using multiple indexes when analyzing tracking and diving data to study foraging behavior. Foraging occurred most commonly in relatively shallow areas with high Sea Surface Temperatures (SST, corresponding to continental shelf areas with Atlantic Water masses. All age and sex classes overlapped spatially to some extent, but the different age and sex groups showed differences in the bathymetry of their foraging areas as well as in their vertical use of the water column. When foraging, pups dove in the upper part of the water column in relatively deep areas. Adult females foraged relatively shallowly in deep water areas too, though in shallower areas than pups. Adult males foraged close to the bottom in shallower areas.

Development and design of a high pressure carbon dioxide system for the separation of hazardous contaminants from non-hazardous debris

International Nuclear Information System (INIS)

Adkins, C.L.J.; Russick, E.M.; Smith, H.M.; Olson, R.B.

1995-01-01

Under the Department of Energy (DOE)/United States Air Force (USAF) Memorandum of Understanding, a system is being designed that will use high pressure carbon dioxide for the separation of oils, greases, and solvents from non-hazardous solid waste. The contaminants are dissolved into the high pressure carbon dioxide and precipitated out upon depressurization. The carbon dioxide solvent can then be recycled for continued use. Excellent extraction capability for common manufacturing oils, greases, and solvents has been measured. It has been observed that extraction performance follows the dilution model if a constant flow system is used. The solvents tested are extremely soluble and have been extracted to 100% under both liquid and mild supercritical carbon dioxide conditions. These data are being used to design a 200 liter extraction system

"Robin Hood" of techno-Turkey or organ trafficking in the state of ethical beings.

Science.gov (United States)

Sanal, Aslihan

2004-09-01

Dr S. is a famous transplant surgeon in the Middle East. He operates "underground" on wealthy patients in different countries, from Israel to Turkey to Russia. The media refer to him as the "Organ Mafia doctor," and patients diagnosed with renal failure speak of him sardonically as "Robin Hood," acknowledging that he takes organs from the poor to give to the rich. But ethical issues of organ trafficking are not limited to marginal private clinics and "Mafia" doctors. All-living related organ transplants in Turkey involve similar ethical dilemmas: many related or nonrelated organ recipients pay their donors, and demand continues to rise. This paper explores practices in state and university hospitals and the ethical dilemmas doctors encounter to understand where and how judicial, cultural, and social categories of "human rights" and "crime" are constructed in our high-tech world.

Statistical modelling of Fat, Oil and Grease (FOG) deposits in wastewater pump sumps.

Science.gov (United States)

Nieuwenhuis, Eva; Post, Johan; Duinmeijer, Alex; Langeveld, Jeroen; Clemens, François

2018-05-15

The accumulation of FOG (Fat, Oil and Grease) deposits in sewer pumping stations results in an increase in maintenance costs, malfunctioning of pumps and, a potential increase of wastewater spills in receiving open water bodies. It is thought that a variety of parameters (e.g. geometry of the pump sump, pump operation, socioeconomic parameters of the catchment) influences the built-up of FOG. Based on a database containing data of 126 pumping stations located in five Dutch municipalities a statistical model was built. It is shown that 3 parameters are most significant in explaining the occurrence of FOG deposits: mean income of the population in a catchment, the amount of energy (kinetic and potential) per m 3 per day and the density of restaurants, bars and hotels in a catchment. Further it is shown that there are significant differences between municipalities that can be traced back to the local 'design paradigm'. For example, in Amsterdam, the design philosophy of discharging in the pump sump under the water surface (and hence maintaining a low level of turbulence in the pump sump) results in an increase of the probability of the formation of FOG. Copyright © 2018 The Authors. Published by Elsevier Ltd.. All rights reserved.

An overview of the 2009 Fort Hood Robotics Rodeo

Science.gov (United States)

Norberg, Seth

2010-04-01

The Robotics Rodeo held from 31 August to 3 September 2009 at Fort Hood, Texas, had three stated goals: educate key decision makers and align the robotics industry; educate Soldiers and developers; and perform a live market survey of the current state of technologies to encourage the development of robotic systems to support operational needs. Both events that comprised the Robotics Rodeo, the Extravaganza and the robotic technology observation, demonstration and discussion (RTOD2) addressed these stated goals. The Extravaganza was designed to foster interaction between the vendors and the visitors who included the media, Soldiers, others in the robotics industry and key decision makers. The RTOD2 allowed the vendors a more private and focused interaction with the subject matter experts teams, this was the forum for the vendors to demonstrate their robotic systems that supported the III Corps operational needs statements that are focused on route clearance, convoy operations, persistent stare, and robotic wingman. While the goals of the Rodeo were achieved, the underlying success from the event is the development of a new business model that is focused on collapsing the current model to get technologies into the hands of our warfighters quicker. This new model takes the real time data collection from the Rodeo, the Warfighter Needs from TRADOC, the emerging requirements from our current engagements, and assistance from industry partners to develop a future Army strategy for the rapid fielding of unmanned systems technologies.

The use of supercritical carbon dioxide for contaminant removal from solid waste

International Nuclear Information System (INIS)

Adkins, C.L.J.; Russick, E.M.; Smith, H.M.; Olson, R.B.

1994-01-01

Supercritical carbon dioxide is being explored as a waste minimization technique for separating oils, greases and solvents from solid waste. The containments are dissolved into the supercritical fluid and precipitated out upon depressurization. The carbon dioxide solvent can then be recycled for continued use. Definitions of the temperature, pressure, flowrate and potential co-solvents are required to establish the optimum conditions for hazardous contaminant removal. Excellent extractive capability for common manufacturing oils, greases, and solvents has been observed in both supercritical and liquid carbon dioxide. Solubility measurements are being used to better understand the extraction process, and to determine if the minimum solubility required by federal regulations is met

Multiple [3H]imipramine binding sites in brains of male and female Fawn-Hooded and Long-Evans rats

International Nuclear Information System (INIS)

Ieni, J.R.; Zukin, S.R.; Praag, H.M. van; Tobach, E.; Barr, G.A.

1985-01-01

Comparisons of high- and low-affinity [ 3 H]imipramine binding to whole brain homogenates from adult male and female rats of the Fawn-Hooded and Long-Evans strains were performed. Most strikingly, no significant differences were observed between the two strains in any of the binding parameters, indicating that brain [ 3 H]imipramine binding sites, which may be related to the serotonergic uptake process, appear normal in a strain of rats with serotonin platelet storage pool disease. However, a significant sex difference in high- but not low-affinity whole brain [ 3 H]imipramine Bsub(max) values was observed, with females of both strains having higher densities than males. (Auth.)

Development and implementation of a propeller test capability for GL-10 "Greased Lightning" propeller design

Science.gov (United States)

Duvall, Brian Edward

Interest in small unmanned aerial vehicles has increased dramatically in recent years. Hybrid vehicles which allow forward flight as a fixed wing aircraft and a true vertical landing capability have always had applications. Management of the available energy and noise associated with electric propeller propulsion systems presents many challenges. NASA Langley has developed the Greased Lightning 10 (GL-10) vertical takeoff, unmanned aerial vehicle with ten individual motors and propellers. All are used for propulsion during takeoff and contribute to acoustic noise pollution which is an identified nuisance to the surrounding users. A propeller test capability was developed to gain an understanding of how the noise can be reduced while meeting minimum thrust requirements. The designed propeller test stand allowed for various commercially available propellers to be tested for potential direct replacement of the current GL-10 propellers and also supported testing of a newly designed propeller provided by the Georgia Institute of Technology. Results from the test program provided insight as to which factors affect the noise as well as performance characteristics. The outcome of the research effort showed that the current GL-10 propeller still represents the best choice of all the candidate propellers tested.

Archeological Investigations in Cochiti Reservoir, New Mexico. Volume 3. 1976-1977 Field Seasons.

Science.gov (United States)

1979-01-01

or methods are in a constant state of flux, and will undoubtedly continue so. The present In 1959, Baumhoff and Heizer suggested that the sys- paper...marrow extraction and when as estimates rather than counts were insect bodies and rendering bone grease. parts (10-25%), cocoons/larvae/eggs (1-10%), and...A yielded rendering bone grease or making soup. The association of 40 burned bone fragments. A 500 ml sample from grid the unidentified fragments and

Association in Long-Evans hooded rats of red cell 2,3-diphosphoglycerate levels with hemoglobin types.

Science.gov (United States)

Brewer, G; Gilman, J; Noble, N; Crews, V

1978-08-01

Two sublines of commercially available Long-Evans hooded rats have been developed by genetic selection. These sublines have widely differing levels of erythrocyte 2,3-diphosphoglycerate (DPG) due to different alleles at a single genetic locus. In the present work, it is shown that rats from the commercial population are also polymorphic at a hemoglobin locus, probably involving two alleles of the IIIbeta-globin chain locus. Particular hemoglobin types have been found to be strongly associated with certain DPG types, not only in the high-DPG and low-DPG lines but also in the commercial population. Two explanations for this association are considered. One is a single-locus hypothesis, with hemoglobin allelic variation causing DPG variation, and the other is a two-locus hypothesis, with marked linkage disequilibrium.

The role of glycogen, glucose and lactate in neuronal activity during hypoxia in the hooded seal (Cystophora cristata) brain.

Science.gov (United States)

Czech-Damal, N U; Geiseler, S J; Hoff, M L M; Schliep, R; Ramirez, J-M; Folkow, L P; Burmester, T

2014-09-05

The brains of diving mammals are repeatedly exposed to hypoxic conditions during diving. Brain neurons of the hooded seal (Cystophora cristata) have been shown to be more hypoxia tolerant than those of mice, but the underlying mechanisms are not clear. Here we investigated the roles of different metabolic substrates for maintenance of neuronal activity and integrity, by comparing the in vitro spontaneous neuronal activity of brain slices from layer V of the visual cortex of hooded seals with those in mice (Mus musculus). Studies were conducted by manipulating the composition of the artificial cerebrospinal fluid (aCSF), containing either 10 mM glucose, or 20 mM lactate, or no external carbohydrate supply (aglycemia). Normoxic, hypoxic and ischemic conditions were applied. The lack of glucose or the application of lactate in the aCSF containing no glucose had little effect on the neuronal activity of seal neurons in either normoxia or hypoxia, while neurons from mice survived in hypoxia only few minutes regardless of the composition of the aCSF. We propose that seal neurons have higher intrinsic energy stores. Indeed, we found about three times higher glycogen stores in the seal brain (∼4.1 ng per μg total protein in the seal cerebrum) than in the mouse brain. Notably, in aCSF containing no glucose, seal neurons can tolerate 20 mM lactate while in mouse neuronal activity vanished after few minutes even in normoxia. This can be considered as an adaptation to long dives, during which lactate accumulates in the blood. Copyright © 2014 IBRO. Published by Elsevier Ltd. All rights reserved.

Transcriptome Analysis Identifies Key Metabolic Changes in the Hooded Seal (Cystophora cristata Brain in Response to Hypoxia and Reoxygenation.

Directory of Open Access Journals (Sweden)

Mariana Leivas Müller Hoff

Full Text Available The brain of diving mammals tolerates low oxygen conditions better than the brain of most terrestrial mammals. Previously, it has been demonstrated that the neurons in brain slices of the hooded seal (Cystophora cristata withstand hypoxia longer than those of mouse, and also tolerate reduced glucose supply and high lactate concentrations. This tolerance appears to be accompanied by a shift in the oxidative energy metabolism to the astrocytes in the seal while in terrestrial mammals the aerobic energy production mainly takes place in neurons. Here, we used RNA-Seq to compare the effect of hypoxia and reoxygenation in vitro on brain slices from the visual cortex of hooded seals. We saw no general reduction of gene expression, suggesting that the response to hypoxia and reoxygenation is an actively regulated process. The treatments caused the preferential upregulation of genes related to inflammation, as found before e.g. in stroke studies using mammalian models. Gene ontology and KEGG pathway analyses showed a downregulation of genes involved in ion transport and other neuronal processes, indicative for a neuronal shutdown in response to a shortage of O2 supply. These differences may be interpreted in terms of an energy saving strategy in the seal's brain. We specifically analyzed the regulation of genes involved in energy metabolism. Hypoxia and reoxygenation caused a similar response, with upregulation of genes involved in glucose metabolism and downregulation of the components of the pyruvate dehydrogenase complex. We also observed upregulation of the monocarboxylate transporter Mct4, suggesting increased lactate efflux. Together, these data indicate that the seal brain responds to the hypoxic challenge by a relative increase in the anaerobic energy metabolism.

Effects of glycerin concentration in steam-flaked corn-based diets with supplemental yellow grease on performance and carcass characteristics of finishing beef steers.

Science.gov (United States)

Buttrey, E K; Luebbe, M K; McCollum, F T; Cole, N A; MacDonald, J C; Hales, K E

2015-07-01

Forty-eight individually fed crossbred steers (initial BW = 381 ± 7.61 kg) were used to determine the effects of glycerin (GLY) concentration in steam-flaked corn (SFC)-based diets with added yellow grease on animal performance and carcass characteristics. Glycerin was included at 0, 2.5, 5, and 10% dietary DM replacing SFC. A completely randomized design was used with steers as the experimental unit, and the model included the fixed effects of diet. Contrast statements were used to determine linear and quadratic effects of GLY inclusion. Final BW and DMI were not affected (P > 0.27) by GLY concentration. Average daily gain and G:F based on live BW did not differ as GLY level increased in the diet from 0 to 10% of DM (P > 0.33). Carcass-adjusted final BW and carcass-adjusted G:F were also not affected by GLY concentration (P > 0.22); however, carcass-adjusted ADG tended to respond quadratically by decreasing from 2.5 to 5% GLY inclusion and increasing thereafter (P = 0.10). Calculated dietary NEm and NEg did not differ as GLY increased in the diet (P > 0.37). Hot carcass weight tended to respond quadratically, decreasing from 2.5 to 5% GLY and increasing thereafter (P = 0.10). Likewise, dressing percentage tended to respond quadratically by decreasing from 2.5 to 5% GLY inclusion and increasing to 10% GLY inclusion (P = 0.09). Fat thickness decreased linearly as GLY inclusion increased in the diet (P 0.21). Calculated yield grade (YG) decreased linearly as GLY increased in the diet from 0 to 10% of DM (P = 0.04). Based on our results, there was no animal performance benefit for replacing SFC with GLY in diets containing yellow grease, and the only change in carcass merit was a slight improvement in YG.

Cassini ISS Observations Of The Early Stages Of The Formation Of Titan's South Polar Hood And Vortex In 2012

Science.gov (United States)

West, Robert A.; Del Genio, A.; Perry, J.; Ingersoll, A. P.; Turtle, E. P.; Porco, C.; Ovanessian, A.

2012-10-01

Northern spring equinox on Titan occurred on August 11, 2009. In March of 2012 the Imaging Science Subsystem (ISS) on the Cassini spacecraft saw the first evidence for the formation of a polar hood in the atmosphere above Titan’s south pole. Views of the limb showed an optical thickening primarily at about 360 km altitude across a few degrees of latitude centered on the pole. Images of Titan in front of Saturn provide a nearly direct measure of the line-of-sight optical depth as a function of latitude and altitude from about 250 km and higher. Two or more distinct layers are seen, both near the pole and at other latitudes. The highest of these, near 360 km altitude, hosts the embryonic polar hood. On June 27, 2012 ISS observed the pole from high latitude. These images show a distinct and unusual cloudy patch, elongated and not centered on the pole and with an elevated perimeter. The morphology and color indicate an unfamiliar (for Titan) composition and dynamical regime. The interior of the feature consists of concentrations of cloud/haze organized on spatial scales of tens of kilometers. Its morphology is reminiscent of the open cellular convection sometimes seen in the atmospheric boundary layer over Earth’s oceans under conditions of large-scale subsidence. Unlike Earth, where such convection is forced by large surface heat fluxes or the onset of drizzle, convection at 360 km on Titan is more likely to be driven from above by radiative cooling. During the 9 hours we observed Titan, this feature completed a little over one rotation around the pole, providing direct evidence for a polar vortex rotating at a rate roughly consistent with angular-momentum-conserving flow for air displaced from the equator. Part of this work was performed by the Jet Propulsion Laboratory, California Institute of Technology.

Evaluation of physical and chemical properties and their interactions in fat, oil, and grease (FOG) deposits.

Science.gov (United States)

Gross, Martin A; Jensen, Jeanette L; Gracz, Hanna S; Dancer, Jens; Keener, Kevin M

2017-10-15

Fat, oil and grease (FOG) blockages in sewer systems are a substantial problem in the United States. It has been estimated that over 50% of sewer overflows are a result of FOG blockages. In this work, a thorough laboratory study was undertaken to examine key variables that contribute to FOG deposit formation under controlled conditions. Physical and chemical properties and their interactions were evaluated and conditions that generated deposits that mimicked field FOG deposits were identified. It was found that 96 of the of 128 reaction conditions tested in the laboratory formed FOG deposits with similar physical and chemical characteristics as field FOG deposits. It was also found that FOG deposits can be created through fatty acid crystallization and not just saponification. Furthermore FOG deposits were found to be more complex than previously documented and contain free fatty acids, fatty acid metal salts, triacylglycerol's, diacylglycerol's and, monoacylglycerol's. Lastly it was found that FOG deposits that only contained saturated fatty acids were on average 2.1 times higher yield strength than deposits that contained unsaturated fatty acids. Copyright © 2017 Elsevier Ltd. All rights reserved.

The regeneration of a multi-ethnic mixed-use area: The case of Robin Hood Chase

Directory of Open Access Journals (Sweden)

Ian Bentley

1997-01-01

Full Text Available Urban designers show increasing interest in promoting community participation in urban regeneration and especially housing regeneration. However, effective participation has proved difficult in multi-ethnic mixed-use areas, with their wide range of different (and often conflicting interest groups. This paper, presented in case-study form, analyses a project in one such area: the Robin Hood Chase local centre in St. Ann’s area of Nottingham. It pays particular attention to the identification of different interest groups and their associated institutions, the use of local media and social events to involve these groups in the urban design process, the use of rearrangeable models in a process of “enquiry by design”, and the production of a widely acceptable urban design strategy for the area. Analysis of feedback from participants indicates a high level of satisfaction both with the final physical design proposal and with the process itself; and also identifies directions for further development in the approach and techniques employed.

Levels of non-essential elements in muscle from harp seal (Phagophilus groenlandicus) and hooded seal (Cystophora cristata) caught in the Greenland Sea area

International Nuclear Information System (INIS)

Brunborg, Linn Anne; Graff, Ingvild Eide; Froyland, Livar; Julshamn, Kare

2006-01-01

The non-essential elements, arsenic, cadmium, mercury and lead, inevitably accumulate in marine top predators such as seals. The concentration of these elements and the essential element selenium, due to its proposed protective properties against mercury toxicity in marine mammals, were measured in muscle, liver and kidney from reproductive active females of harp seal (Phagophilus groenlandicus) and hooded seal (Cystophora cristata) caught in the drift ice between Iceland and East Greenland. Arsenic levels were below 1 μg/g w.w. in all analysed samples, and were therefore low compared to other seafood products. The concentrations of arsenic found in the present study were comparable to the results reported in a similar study from 1985. Mean concentrations of total mercury in muscle from the present study were higher than levels in other seafood products. The levels of total mercury from the present study showed a tendency of lower levels in all tissue samples compared to the study from 1985. Methyl mercury displayed a trend of a lower ratio of methyl mercury to total mercury as the concentration of total mercury increased, indicating a demethylation of methyl mercury at high total mercury concentrations (e.g. mercury in liver of hooded seal). The concentration ratio of methyl mercury to total mercury in muscle samples was more than 75%, with total mercury concentration less than 0.5 μg/g w.w., whereas the ratio for liver was as low as 0.2% with a total mercury concentration of 128 μg/g w.w. The molar concentration ratios of selenium to mercury showed that selenium was present in a molar surplus to mercury in all tissues with low mercury concentration. However, there seemed to be a general mobilisation of selenium in liver and kidney tissues of harp seal and hooded seal, whereas an extraordinary mobilisation seemed to take place at hepatic mercury concentrations exceeding 50 μg/g w.w. The mean concentrations of lead in muscles in the present study were higher

Lidar-enhanced geologic mapping, examples from the Medford and Hood River areas, Oregon

Science.gov (United States)

Wiley, T. J.; McClaughry, J. D.

2012-12-01

Lidar-based 3-foot digital elevation models (DEMs) and derivatives (slopeshade, hillshade, contours) were used to help map geology across 1700 km2 (650 mi2) near Hood River and Medford, Oregon. Techniques classically applied to interpret coarse DEMs and small-scale topographic maps were adapted to take advantage of lidar's high resolution. Penetration and discrimination of plant cover by the laser system allowed recognition of fine patterns and textures related to underlying geologic units and associated soils. Surficial geologic maps were improved by the ability to examine tiny variations in elevation and slope. Recognition of low-relief features of all sizes was enhanced where pixel elevation ranges of centimeters to meters, established by knowledge of the site or by trial, were displayed using thousands of sequential colors. Features can also be depicted relative to stream level by preparing a DEM that compensates for gradient. Near Medford, lidar-derived contour maps with 1- to 3-foot intervals revealed incised bajada with young, distal lobes defined by concentric contour lines. Bedrock geologic maps were improved by recognizing geologic features associated with surface textures and patterns or topographic anomalies. In sedimentary and volcanic terrain, structure was revealed by outcrops or horizons lying at one stratigraphic level. Creating a triangulated irregular network (TIN) facet from positions of three or more such points gives strike and dip. Each map area benefited from hundreds of these measurements. A more extensive DEM in the plane of the TIN facet can be subtracted from surface elevation (lidar DEM) to make a DEM with elevation zero where the stratigraphic horizon lies at the surface. The distribution of higher and lower stratigraphic horizons can be shown by highlighting areas similarly higher or lower on the same DEM. Poor fit of contacts or faults projected between field traverses suggest the nature and amount of intervening geologic structure

Residential and service-population exposure to multiple natural hazards in the Mount Hood region of Clackamas County, Oregon

Science.gov (United States)

Mathie, Amy M.; Wood, Nathan

2013-01-01

The objective of this research is to document residential and service-population exposure to natural hazards in the rural communities of Clackamas County, Oregon, near Mount Hood. The Mount Hood region of Clackamas County has a long history of natural events that have impacted its small, tourism-based communities. To support preparedness and emergency-management planning in the region, a geospatial analysis of population exposure was used to determine the number and type of residents and service populations in flood-, wildfire-, and volcano-related hazard zones. Service populations are a mix of residents and tourists temporarily benefitting from local services, such as retail, education, or recreation. In this study, service population includes day-use visitors at recreational sites, overnight visitors at hotels and resorts, children at schools, and community-center visitors. Although the heavily-forested, rural landscape suggests few people are in the area, there are seasonal peaks of thousands of visitors to the region. “Intelligent” dasymetric mapping efforts using 30-meter resolution land-cover imagery and U.S. Census Bureau data proved ineffective at adequately capturing either the spatial distribution or magnitude of population at risk. Consequently, an address-point-based hybrid dasymetric methodology of assigning population to the physical location of buildings mapped with a global positioning system was employed. The resulting maps of the population (1) provide more precise spatial distributions for hazard-vulnerability assessments, (2) depict appropriate clustering due to higher density structures, such as apartment complexes and multi-unit commercial buildings, and (3) provide new information on the spatial distribution and temporal variation of people utilizing services within the study area. Estimates of population exposure to flooding, wildfire, and volcanic hazards were determined by using overlay analysis in a geographic information system

Fort Hood Solar Total Energy Project. Volume II. Preliminary design. Part 2. System performance and supporting studies. Final report

Energy Technology Data Exchange (ETDEWEB)

None,

1979-01-01

The preliminary design developed for the Solar Total Energy System to be installed at Fort Hood, Texas, is presented. System performance analysis and evaluation are described. Feedback of completed performance analyses on current system design and operating philosophy is discussed. The basic computer simulation techniques and assumptions are described and the resulting energy displacement analysis is presented. Supporting technical studies are presented. These include health and safety and reliability assessments; solar collector component evaluation; weather analysis; and a review of selected trade studies which address significant design alternatives. Additional supporting studies which are generally specific to the installation site are reported. These include solar availability analysis; energy load measurements; environmental impact assessment; life cycle cost and economic analysis; heat transfer fluid testing; meteorological/solar station planning; and information dissemination. (WHK)

University of Missouri research reactor exhaust ventilation/laboratory fume hood upgrade

International Nuclear Information System (INIS)

Edwards, C.B. Jr.; McKibben, J.C.; McCracken, C.B.

1989-01-01

The University of Missouri research reactor (MURR) facility is located in Research Park, 1 mile south of the Columbia campus. The reactor is a 10-MW pressurized loop, in-pool-type, light-water-moderated, beryllium-and-graphite-reflected core, serviced by six radial beam tubes for research, and has sample irradiation facilities in both a flux trap and in the graphite region. The reactor operates at full power 150 h/week, 52 week/yr, making it one of the best operating schedules and the most extensively used of any university research reactor. This extensive utilization includes many programs, such as radioisotope applications, neutron activation analysis, etc., that depend heavily on fume hoods, glove boxes, and hot cells that put a tremendous demand on the exhaust system. The exhaust system is required to be operable whenever the reactor is operating and must have the capability of being operated from an emergency electrical generator on loss of site electrical power. The originally installed exhaust ventilation system was below needed capacity and, with increased program requirements and system age, the necessity to upgrade the system was paramount. The challenge was to complete the upgrade construction while continuing to operate the reactor and maintain all the other ongoing programs, rather than take the easy way of an extended shutdown. This paper discusses how MURR met this challenge and solved these problems, problems that are similarly experienced by almost all research reactors to some degree when major work is required on critical systems

Accumulation of oil and grease in soils irrigated with greywater and their potential role in soil water repellency.

Science.gov (United States)

Travis, Micheal J; Weisbrod, Noam; Gross, Amit

2008-05-01

The potential impact of oil and grease (O and G) to soils irrigated with greywater (GW) was investigated. Greywater streams were sampled and analyzed for O and G content, along with corresponding GW-irrigated soils. Untreated kitchen GW averaged 200 mg L(-1) O and G, over an order of magnitude more than other GW streams. GW-irrigated soils showed O and G accumulation of up to 200 mg kg(-l) within the first 20-cm of depth. To determine the potential effects of such O and G accumulation on water movement in soil, capillary rise and water drop penetration time (WDPT) experiments were conducted. The results showed up to 60% decrease in capillary rise when sand containing 250 mg kg(-1) O and G was used. Interestingly, no additional reduction in capillary rise was observed at concentrations above 250 mg kg(-1). WDPT was observed to increase linearly with increased O and G content, up to 1000 mg kg(-1). This work demonstrated that O and G in GW used for irrigation can accumulate in soil and may lead to a significant reduction in the soils ability to transmit water.

Understanding the spatial formation and accumulation of fats, oils and grease deposits in the sewer collection system.

Science.gov (United States)

Dominic, Christopher Cyril Sandeep; Szakasits, Megan; Dean, Lisa O; Ducoste, Joel J

2013-01-01

Sanitary sewer overflows are caused by the accumulation of insoluble calcium salts of fatty acids, which are formed by the reaction between fats, oils and grease (FOG) and calcium found in wastewaters. Different sewer structural configurations (i.e., manholes, pipes, wet wells), which vary spatially, along with other obstructions (roots intrusion) and pipe deformations (pipe sags), may influence the detrimental buildup of FOG deposits. The purpose of this study was to quantify the spatial variation in FOG deposit formation and accumulation in a pilot-scale sewer collection system. The pilot system contained straight pipes, manholes, roots intrusion, and a pipe sag. Calcium and oil were injected into the system and operated at alkaline (pH = 10) and neutral (pH = 7) pH conditions. Results showed that solid accumulations were slightly higher at neutral pH. Fourier transform infrared (FTIR) analysis on the solids samples confirmed that the solids were indeed calcium-based fatty acid salts. However, the fatty acid profiles of the solids deviated from the profile found from FOG deposits in sewer systems, which were primarily saturated fatty acids. These results confirm the work done previously by researchers and suggest an alternative fate of unsaturated fatty acids that does not lead to their incorporation in FOG deposits in full-scale sewer systems.

A Dose–Response Analysis of the Reproductive Effects of a Single Gestational Dose of 2,3,7,8-Tetrachlorodibenzo-p-dioxin in Male Long Evans Hooded Rat Offspring,

OpenAIRE

Gray, L. E.; Ostby, J. S.; Kelce, W. R.

1997-01-01

Male rats exposedin uteroto 2,3,7,8-tetrachlorodibenzo-p-dioxin (TCDD) display reduced fertility as a consequence of the direct action of TCDD on the epididymides, as well as delayed puberty and altered reproductive organ weights. The current study provides dose–response data for the reproductive effects of TCDD, administered during pregnancy, with an emphasis on the effects of TCDD on testicular, epididymal, and ejaculated sperm numbers. Long Evans Hooded rats were dosed by gavage with 0, 0....

Natural ventilation of a generic cask under a transport hood - CFD and analytical modelling

Energy Technology Data Exchange (ETDEWEB)

Powell, D.; Davies, G.; Tso, C.F. [Arup, London (United Kingdom)

2004-07-01

In comparison with finite element simulation for structural and thermal behaviour, the use of computational fluid dynamics technique (hereafter CFD) to analyse, predict and design air and heat flow in package design is relatively novel. Arup has been using CFD techniques to investigate fluid and heat flow, and to use it as a tool to design fluid and heat flow across a broad spectrum of industries for over fifteen years. In order demonstrate the power of the technique and its benefits, the airflow and heat flow characteristics around a transport package during transit under a transport hood has been evaluated using the CFD technique. This paper presents the scenario, the model, the analysis technique and the results of this analysis. Comparison with test results is probably the best way to validate a CFD analysis. In the absence of test results, the analysis was verified by comparison with hand calculation solutions. The scenario as it stands is too complex and hand calculation solution cannot describe the scenario sufficiently. However, hand calculation solutions could be derived for simplified version of the scenario against which CFD analysis of the simplified scenario can be compared. The second half of this paper describes the verification out.

Natural ventilation of a generic cask under a transport hood - CFD and analytical modelling

International Nuclear Information System (INIS)

Powell, D.; Davies, G.; Tso, C.F.

2004-01-01

In comparison with finite element simulation for structural and thermal behaviour, the use of computational fluid dynamics technique (hereafter CFD) to analyse, predict and design air and heat flow in package design is relatively novel. Arup has been using CFD techniques to investigate fluid and heat flow, and to use it as a tool to design fluid and heat flow across a broad spectrum of industries for over fifteen years. In order demonstrate the power of the technique and its benefits, the airflow and heat flow characteristics around a transport package during transit under a transport hood has been evaluated using the CFD technique. This paper presents the scenario, the model, the analysis technique and the results of this analysis. Comparison with test results is probably the best way to validate a CFD analysis. In the absence of test results, the analysis was verified by comparison with hand calculation solutions. The scenario as it stands is too complex and hand calculation solution cannot describe the scenario sufficiently. However, hand calculation solutions could be derived for simplified version of the scenario against which CFD analysis of the simplified scenario can be compared. The second half of this paper describes the verification out

A full-scale UASB reactor for treatment of pig and cattle slaughterhouse wastewater with a high oil and grease content

Directory of Open Access Journals (Sweden)

L. A. S. Miranda

2005-12-01

Full Text Available This paper discusses the performance of an 800m³ full-scale UASB reactor in treating meat-packing plant and slaughterhouse effluents containing high concentrations of oil and grease (O&G (413-645 mg/L, resulting in a COD/O&G ratio of 26-32%. Those macromolecules were considered responsible for the unbalance of the system resulting in a total washout of the biomass. The removal of O&G from the influent using a physicochemical system (coagulation-flocculation improved the physical characteristics of the anaerobic sludge, controlling the biomass washout. Reactor performance was significantly improved when the COD/O&G ratio influent was maintained in the 10%. The COD and O&G removal rates obtained after implantation of the physicochemical system were 70-92% and 27-58%, respectively. The specific methanogenic activity (SMA of the biomass shows towards a tendency stabilisation and adaptation to the substrate influent. Pretreatment of the influent allowed the maximum organic load to be increased (1.46 to 2.43 Kg COD/m³.d and improved the quality of the effluent.

The Canadian residential duct and chimney survey

Energy Technology Data Exchange (ETDEWEB)

Fugler, D.

2003-12-01

A study was conducted in 1989 to better understand the thermal performance of ducts and chimneys in houses. The objective was to address the problems associated with insufficient airflow and backdrafting of combustion gases resulting from malfunctioning fans, furnaces and fireplaces. The Duct Test Rig was used to measure and recorded airflows and heat losses in a variety of ducts and chimneys in a representative mix of houses in Vancouver, Kelowna, Winnipeg, Calgary, Toronto, London, Montreal, Quebec City, Halifax, Fredericton and Ottawa. Bath, kitchen, clothes dryer and central vacuum exhaust fans were tested to determine how performance is affected by fan age, accumulations of dust, grease, bugs and installation methods. Results indicate that there is no statistical difference between axial or centrifugal fans. The greatest problem appeared to be with low flows, high leakage rates, and poor conditions of bathroom fans. Many kitchen fans were found to be blocked at the inlet by cooking grease. The exhaust flows depended greatly on the condition of the backdraft damper. Dryer exhaust airflow was typically less than the 75 L/s specified by manufacturers, but even old dryers performed relatively well. All types of chimneys were tested for different positive hood pressures, airflow lost through leakage, and thermal characteristics. Airflow was found to vary depending on the type and area of the flue and the presence of a cap. For heating systems, the low duct efficiency was due mostly to duct leakage, radiation losses and restrictive ducts and registers. The findings of this testing program are still valid today. 3 tabs.

Evaluating and modeling biogas production from municipal fat, oil, and grease and synthetic kitchen waste in anaerobic co-digestions.

Science.gov (United States)

Li, Chenxi; Champagne, Pascale; Anderson, Bruce C

2011-10-01

The feasibility of using synthetic kitchen waste (KW) and fat, oil, and grease (FOG) as co-substrates in the anaerobic digestion of waste activated sludge (WAS) was investigated using two series of biochemical methane potential (BMP) tests. Ranges of ideal substrate to inoculum (S/I) ratio were determined for the FOG (0.25-0.75) and KW (0.80-1.26) as single substrates in the first experiment. The second experiment, which estimated the methane production performances of FOG and KW as co-substrates for WAS co-digestion, was conducted based on the optimal parameters selected from the results of the first experiment. Results indicated that co-digestions with FOG and KW enhanced methane production from 117±2.02 mL/gTVS (with only WAS) to 418±13.7 mL/gTVS and 324±4.11 mL/gTVS, respectively. FOG exhibited more biogas production than KW as co-substrate. Non-linear regression results showed that co-substrate addition shortened the lag phases of organic biodegradation from 81.8 (with only WAS) to 28.3 h with FOG and 3.90 h with KW. Copyright © 2011 Elsevier Ltd. All rights reserved.

A method of evolving novel feature extraction algorithms for detecting buried objects in FLIR imagery using genetic programming

Science.gov (United States)

Paino, A.; Keller, J.; Popescu, M.; Stone, K.

2014-06-01

In this paper we present an approach that uses Genetic Programming (GP) to evolve novel feature extraction algorithms for greyscale images. Our motivation is to create an automated method of building new feature extraction algorithms for images that are competitive with commonly used human-engineered features, such as Local Binary Pattern (LBP) and Histogram of Oriented Gradients (HOG). The evolved feature extraction algorithms are functions defined over the image space, and each produces a real-valued feature vector of variable length. Each evolved feature extractor breaks up the given image into a set of cells centered on every pixel, performs evolved operations on each cell, and then combines the results of those operations for every cell using an evolved operator. Using this method, the algorithm is flexible enough to reproduce both LBP and HOG features. The dataset we use to train and test our approach consists of a large number of pre-segmented image "chips" taken from a Forward Looking Infrared Imagery (FLIR) camera mounted on the hood of a moving vehicle. The goal is to classify each image chip as either containing or not containing a buried object. To this end, we define the fitness of a candidate solution as the cross-fold validation accuracy of the features generated by said candidate solution when used in conjunction with a Support Vector Machine (SVM) classifier. In order to validate our approach, we compare the classification accuracy of an SVM trained using our evolved features with the accuracy of an SVM trained using mainstream feature extraction algorithms, including LBP and HOG.

Using stochastic gradient boosting to infer stopover habitat selection and distribution of Hooded Cranes Grus monacha during spring migration in Lindian, Northeast China.

Science.gov (United States)

Cai, Tianlong; Huettmann, Falk; Guo, Yumin

2014-01-01

The Hooded Crane (Grus monacha) is a globally vulnerable species, and habitat loss is the primary cause of its decline. To date, little is known regarding the specific habitat needs, and stopover habitat selection in particular, of the Hooded Crane. In this study we used stochastic gradient boosting (TreeNet) to develop three specific habitat selection models for roosting, daytime resting, and feeding site selection. In addition, we used a geographic information system (GIS) combined with TreeNet to develop a species distribution model. We also generated a digital map of the relative occurrence index (ROI) of this species at daytime resting sites in the study area. Our study indicated that the water depth, distance to village, coverage of deciduous leaves, open water area, and density of plants were the major predictors of roosting site selection. For daytime resting site selection, the distance to wetland, distance to farmland, and distance to road were the primary predictors. For feeding site selection, the distance to road, quantity of food, plant coverage, distance to village, plant density, distance to wetland, and distance to river were contributing factors, and the distance to road and quantity of food were the most important predictors. The predictive map showed that there were two consistent multi-year daytime resting sites in our study area. Our field work in 2013 using systematic ground-truthing confirmed that this prediction was accurate. Based on this study, we suggest that Lindian plays an important role for migratory birds and that cultivation practices should be adjusted locally. Furthermore, public education programs to promote the concept of the harmonious coexistence of humans and cranes can help successfully protect this species in the long term and eventually lead to its delisting by the IUCN.

Using stochastic gradient boosting to infer stopover habitat selection and distribution of Hooded Cranes Grus monacha during spring migration in Lindian, Northeast China.

Directory of Open Access Journals (Sweden)

Tianlong Cai

Full Text Available The Hooded Crane (Grus monacha is a globally vulnerable species, and habitat loss is the primary cause of its decline. To date, little is known regarding the specific habitat needs, and stopover habitat selection in particular, of the Hooded Crane. In this study we used stochastic gradient boosting (TreeNet to develop three specific habitat selection models for roosting, daytime resting, and feeding site selection. In addition, we used a geographic information system (GIS combined with TreeNet to develop a species distribution model. We also generated a digital map of the relative occurrence index (ROI of this species at daytime resting sites in the study area. Our study indicated that the water depth, distance to village, coverage of deciduous leaves, open water area, and density of plants were the major predictors of roosting site selection. For daytime resting site selection, the distance to wetland, distance to farmland, and distance to road were the primary predictors. For feeding site selection, the distance to road, quantity of food, plant coverage, distance to village, plant density, distance to wetland, and distance to river were contributing factors, and the distance to road and quantity of food were the most important predictors. The predictive map showed that there were two consistent multi-year daytime resting sites in our study area. Our field work in 2013 using systematic ground-truthing confirmed that this prediction was accurate. Based on this study, we suggest that Lindian plays an important role for migratory birds and that cultivation practices should be adjusted locally. Furthermore, public education programs to promote the concept of the harmonious coexistence of humans and cranes can help successfully protect this species in the long term and eventually lead to its delisting by the IUCN.

Pemanfaatan lemak fleshing tersulfonasi untuk peminyakan pada proses penyamakan kulit

Directory of Open Access Journals (Sweden)

Sri Sutyasmi

2009-06-01

Full Text Available The objective of this research was to produce sulfonated oil of fleshing grease and to use for fat liquoring process in leather tanning industries. Fleshing wastes were collected from Yogyakarta. The extract was obtained from fleshing waste by boiling at 100o C for 15 minute 400 – 450 g of extract contained 99.96% of fat were obtained from 5 kg of fleshing. The extract then was sulfonated to increase solubility in water and more reactive with the fiber of processed skin. The sulfonated extract was then analyzed to determine content, iodine value, acid value and saponification value. The result of analysis showed that fat/grease content 158.48. While fat content of goat skin fleshing was 30.27%, iodine value 92.30, acid value 23.74and saponification value 157.03. The quantity parameters are able to meet requirement for leather tanning. Sulfonated extract was then used for fat liquoring process of goat skin with the variation of concentration 4,5 and 6% respectively. Control was made by using 5% synthetic oil. The result of crust testing in this research showed that all of quality parameters meet the document of SNI 06-3536-1994 about goat/sheep crust leather.

40 CFR Appendix G to Subpart A of... - UNEP Recommendations for Conditions Applied to Exemption for Essential Laboratory and Analytical...

Science.gov (United States)

2010-07-01

... calibration; use as extraction solvents, diluents, or carriers for chemical analysis; biochemical research; inert solvents for chemical reactions, as a carrier or laboratory chemical and other critical analytical... global laboratory exemption: a. Testing of oil and grease and total petroleum hydrocarbons in water; b...

A cannabigerol-rich Cannabis sativa extract, devoid of [INCREMENT]9-tetrahydrocannabinol, elicits hyperphagia in rats.

Science.gov (United States)

Brierley, Daniel I; Samuels, James; Duncan, Marnie; Whalley, Benjamin J; Williams, Claire M

2017-06-01

Nonpsychoactive phytocannabinoids (pCBs) from Cannabis sativa may represent novel therapeutic options for cachexia because of their pleiotropic pharmacological activities, including appetite stimulation. We have recently shown that purified cannabigerol (CBG) is a novel appetite stimulant in rats. As standardized extracts from Cannabis chemotypes dominant in one pCB [botanical drug substances (BDSs)] often show greater efficacy and/or potency than purified pCBs, we investigated the effects of a CBG-rich BDS, devoid of psychoactive [INCREMENT]-tetrahydrocannabinol, on feeding behaviour. Following a 2 h prefeed satiation procedure, 16 male Lister-hooded rats were administered CBG-BDS (at 30-240 mg/kg) or vehicle. Food intake, meal pattern microstructure and locomotor activity were recorded over 2 h. The total food intake was increased by 120 and 240 mg/kg CBG-BDS (1.53 and 1.36 g, respectively, vs. 0.56 g in vehicle-treated animals). Latency to feeding onset was dose dependently decreased at all doses, and 120 and 240 mg/kg doses increased both the number of meals consumed and the cumulative size of the first two meals. No significant effect was observed on ambulatory activity or rearing behaviour. CBG-BDS is a novel appetite stimulant, which may have greater potency than purified CBG, despite the absence of [INCREMENT]-tetrahydrocannabinol in the extract.

The use of paleo-imaging and microbiological testing in the analysis of antique cultural material: multislice tomography, and microbial analysis of the Trogir Cathedral cope hood depicting St. Martin and a beggar.

Science.gov (United States)

Cavka, Mislav; Petaros, Anja; Kavur, Lovro; Skrlin, Jasenka; Mlinaric Missoni, Emilija; Jankovic, Ivor; Brkljacic, Boris

2013-01-01

Paleoradiology is the study of biological and other materials from archeological settings through the use of various medical imaging techniques. Although it is most often used in the scientific study of ancient human remains, it can also be used to study metals, ceramics, paper, and clothes. The aim of this study was to test two paleoimaging techniques (MSCT and mammography) in the analysis of an important Croatian liturgical vestment: the hood of a bishop's cope from St. Lawrence's Treasury in Trogir depicting St. Martin and a beggar. To ensure a safe environment for scientists participating in the analysis, a preliminary microbiological analysis was performed, which contributed to the database of microbiological flora found on Croatian archeological remains and relics studied to date. Due to a great amount of metal filaments, the paleoradiological analysis did not produce satisfactory results. However, a digitally enhanced image clearly showed fine metal embroidery of the hood that was not so easily perceived by naked eye. This article argues in favor of expanding paleoradiological studies on materials other than human remains and also of publishing unsatisfactory results, as important lessons for future development of techniques and methods to analyze ancient remains and seek answers about human historical and cultural heritage.

VINTE ANOS DA LEI ROBIN HOOD: UM BALANÇO DA PROTEÇÃO DO PATRIMÔNIO CULTURAL EM MINAS GERAIS (Dossiê: Gestão, Educação e Patrimônio Cultural

Directory of Open Access Journals (Sweden)

Helaine Nolasco Queiroz

2015-06-01

Full Text Available Resumo: O presente texto busca discutir o impacto causado na preservação do patrimônio cultural mineiro pela lei Robin Hood ou Lei do ICMS que, em 2015, completa vinte anos de vigência. Ele partiu das reflexões apresentadas no XIX Simpósio Regional da ANPUH, realizado em Juiz de Fora em 2014, cujo tema foi Profissão historiador: formação e mercado de trabalho, e mostrou-se digno de maior divulgação e publicaçao pela atualidade e relevância do tema. O objetivo é conjecturar sobre as mudanças trazidas pela lei na preservação do patrimônio de Minas Gerais tanto no órgão fiscalizador da preservação no estado quanto nos municípios que aderiram à lei e, ainda, na atuação profissional dos que se dedicam à área. Palavras-chave: Patrimônio cultural, ICMS cultural, Lei Robin Hood, Minas Gerais, IEPHA/MG   Abstract: This text intends to discuss the impact caused in the Cultural Heritage of Minas Gerais (Brazil by the Robin Wood Law, or Low of the ICMS, that completes 20 years of existence in 2015. The idea received an explanation in the XIX Regional Simposion of ANPUH that took place in Juiz de Fora (Minas Gerais, Brazil in 2014. The theme of the simposium was The profession of historian: superior education and work marketing and it showed the actuality and the relevance of deeper discusstions about the subject. The purpose of the article is to reflect about the changes brought by the law in the cultural heritage preservation in Minas Gerais, in the organ that inspects the aplication of the law, in the cities that gain the ressourcers of the law and in the actuation of the professionals of the area.Keywords: Cultural Heritage, ICMS Law, Robin Hood Law, Minas Gerais (Brazil, IEPHARecebido em: 20/05/2015 – Aceito em 23/06/2015

Fat, oil and grease deposits in sewers: characterisation of deposits and formation mechanisms.

Science.gov (United States)

Williams, J B; Clarkson, C; Mant, C; Drinkwater, A; May, E

2012-12-01

Fat, oil and grease deposits (FOG) in sewers are a major problem and can cause sewer overflows, resulting in environmental damage and health risks. Often simplistically portrayed as cooling of fats, recent research has suggested that saponification may be involved in FOG formation. However there are still questions about the mechanisms effecting transformations in sewers and the role and source of metal cations involved in saponification. This study characterises FOG deposits from pumping stations, sewers and sewage works from different water hardness zones across the UK. The sites all had previous problems with FOG and most catchments contained catering and food preparation establishments. The FOG deposits were highly variable with moisture content ranging from 15 to 95% and oil content from 0 to 548 mg/g. Generally the pumping stations had lower moisture content and higher fat content, followed by the sewers then the sewage works. The water in contact with the FOG had high levels of oil (mean of about 800 mg/L) and this may indicate poor kitchen FOG management practices. FOG fatty acid profiles showed a transformation from unsaturated to saturated forms compared to typical cooking oils. This seems to relate to ageing in the sewer network or the mechanism of formation, as samples from pumping stations had higher proportions of C18:1 compared to C16. This may be due to microbial transformations by bacteria such as Clostridium sp. in a similar process to adipocere formation. There was an association between water hardness and increased Ca levels in FOG along with harder deposits and higher melting points. A link between FOG properties and water hardness has not been previously reported for field samples. This may also be due to microbial processes, such as biocalcification. By developing the understanding of these mechanisms it may be possible to more effectively control FOG deposits, especially when combined with promotion of behavioural change. Copyright © 2012

Haul-out behavior of harbor seals (Phoca vitulina in Hood Canal, Washington.

Directory of Open Access Journals (Sweden)

Josh M London

Full Text Available The goal of this study was to model haul-out behavior of harbor seals (Phoca vitulina in the Hood Canal region of Washington State with respect to changes in physiological, environmental, and temporal covariates. Previous research has provided a solid understanding of seal haul-out behavior. Here, we expand on that work using a generalized linear mixed model (GLMM with temporal autocorrelation and a large dataset. Our dataset included behavioral haul-out records from archival and VHF radio tag deployments on 25 individual seals representing 61,430 seal hours. A novel application for increased computational efficiency allowed us to examine this large dataset with a GLMM that appropriately accounts for temporal autocorellation. We found significant relationships with the covariates hour of day, day of year, minutes from high tide and year. Additionally, there was a significant effect of the interaction term hour of day : day of year. This interaction term demonstrated that seals are more likely to haul out during nighttime hours in August and September, but then switch to predominantly daylight haul-out patterns in October and November. We attribute this change in behavior to an effect of human disturbance levels. This study also examined a unique ecological event to determine the role of increased killer whale (Orcinus orca predation on haul-out behavior. In 2003 and 2005 these harbor seals were exposed to unprecedented levels of killer whale predation and results show an overall increase in haul-out probability after exposure to killer whales. The outcome of this study will be integral to understanding any changes in population abundance as a result of increased killer whale predation.

Analysis of grease contamination influence on the internal radial clearance of ball bearings by thermographic inspection

Directory of Open Access Journals (Sweden)

Mišković Žarko Z.

2016-01-01

Full Text Available One of the most important factors influencing ball bearings service life is its internal radial clearance. However, this parameter is also very complex because it depends on applied radial load and ball bearings dimensions, surface finish and manufacturing materials. Thermal condition of ball bearings also significantly affects internal radial clearance. Despite many researches performed in order to find out relevant facts about different aspects of ball bearings thermal behaviour, only few of them are dealing with the real working conditions, where high concentration of solid contaminant particles is present. That’s why the main goal of research presented in this paper was to establish statistically significant correlation between ball bearings temperatures, their working time and concentration of contaminant particles in their grease. Because of especially difficult working conditions, the typical conveyor idlers bearings were selected as representative test samples and appropriate solid particles from open pit coal mines were used as artificial contaminants. Applied experimental methodology included thermographic inspection, as well as usage of custom designed test rig for ball bearings service life testing. Finally, by obtained experimental data processing in advanced software, statistically significant mathematical correlation between mentioned bearings characteristics was determined and applied in commonly used internal radial clearance equation. That is the most important contribution of performed research - the new equation and methodology for ball bearings internal clearance determination which could be used for eventual improvement of existing bearings service life equations. [Projekat Ministarstva nauke Republike Srbije, br. TR35029 i br. TR14033

Analysis of in-service inspection guides for post-tensioning systems in containment structures with greased tendons

International Nuclear Information System (INIS)

Bae, I. H.; Choi, I. G.; Seo, J. M.

2000-01-01

Prestressed concrete containments(PCC) are inspected periodically to ensure structural integrity and to identify and correct problems before they come critical. These inspections are conducted in accordance with the Nuclear Regulatory Committee(NRC) Regulatory Guide. As experience with the surveillance mounts, the guide is revised to keep pace with technological advances in containment design and to reflect the knowledge obtained experience. In the study, an analysis of the available utility surveillance data and an evaluation of the NRC Regulatory Guide and the ASME Code are conducted. The results indicate that the average value of the lower bound defined in Regulatory Guide 1.35.1 can be less than the minimum required force level at 40 years for the existing containment and thus an acceptable alternative has to be presented to meet the allowance of the guide. Tendons in excess of the upper bound or 70% of the ultimate tensile strength of the tendon are observed. Such an occurrence indicates tendon behavior outside the tolerance band that expected, and the cause of such behavior has to be investigated. It is shown that the behavior of the predicted prestressing force with time based on assumed losses does quite different from that of the measured tendon force with time and, therefore, studies for the significant factors, such as shrinkage and creep of concrete, that influence the time-dependent losses in PCC are needed. Additional research on the long-term effects of the impurity levels on the effectiveness of the grease seems justified

Reactor performance and microbial community dynamics during anaerobic co-digestion of municipal wastewater sludge with restaurant grease waste at steady state and overloading stages.

Science.gov (United States)

Razaviarani, Vahid; Buchanan, Ian D

2014-11-01

Linkage between reactor performance and microbial community dynamics was investigated during mesophilic anaerobic co-digestion of restaurant grease waste (GTW) with municipal wastewater sludge (MWS) using 10L completely mixed reactors and a 20day SRT. Test reactors received a mixture of GTW and MWS while control reactors received only MWS. Addition of GTW to the test reactors enhanced the biogas production and methane yield by up to 65% and 120%, respectively. Pyrosequencing revealed that Methanosaeta and Methanomicrobium were the dominant acetoclastic and hydrogenotrophic methanogen genera, respectively, during stable reactor operation. The number of Methanosarcina and Methanomicrobium sequences increased and that of Methanosaeta declined when the proportion of GTW in the feed was increased to cause an overload condition. Under this overload condition, the pH, alkalinity and methane production decreased and VFA concentrations increased dramatically. Candidatus cloacamonas, affiliated within phylum Spirochaetes, were the dominant bacterial genus at all reactor loadings. Copyright © 2014 Elsevier Ltd. All rights reserved.

Digestibility of energy and lipids and oxidative stress in nursery pigs fed commercially available lipids

Science.gov (United States)

An experiment was conducted to evaluate the impact of lipid source on GE and ether extract (EE) digestibility, oxidative stress, and gut integrity in nursery pigs fed diets containing 10% of soybean oil (SO), choice white grease (CWG), palm oil (PO), or 2 different distillers corn oils (DCO-1 and DC...

In vitro antimicrobial properties of friedelan-3-one from Pterocarpus ...

African Journals Online (AJOL)

MRS I.C ODEH

2016-04-06

Apr 6, 2016 ... purchased from Sigma-Aldrich® with the exception of Silica gel 60. F254 Thin Layer ... The powder was obtained using mortar and pestle. ... The extracts were concentrated and allowed to dry in a fume hood to give the crude ...

Organochlorine Pesticide Residues in the Major Rivers of Southern Thailand

Directory of Open Access Journals (Sweden)

Abd Naser Haji Samoh

2009-01-01

Full Text Available Environmental contaminations by organochlorine pesticides (OCPs of inland water have been a global issue, since most of these compounds are very persistent, bioaccumulative and toxic compounds. Due to the widespread use of DDT for malaria vector eradication programs in the past and no comprehensive works have been conducted to assess trace organic pollutants in river waters, this work is the first effort to assess the contamination levels of OCPs in the major rivers of Southern Thailand. The objectives of this study were to determine the concentration levels of OCPs and oil and grease in the 3 major rivers and to compare the present results with surrounding regions for further assessment of OCPs contamination status in inland waters of Southern Thailand. The water samples were collected along the 3 major rivers (Saiburi, Patani and Tiba River during June 2007-February 2008. Water samples were solid phase extracted with Supelco C-18 cartridge (1g/6 mL and quantified by gas chromatograph (GC-ECD. The concentration of oil and grease was determined by gravimetric method and reported as hexane extractable material (HEM and silica gel treated hexane extractable material (SGT-HEM. Several parameters of waters such as total suspended solid, pH, turbidity, and conductivity were measured. The commonly found OCP residues in these rivers were β-HCH, γ-HCH, heptachlor epoxide, endosulfan 1, p,p’- DDE and endrin aldehyde. The overall results showed that Saiburi River was more polluted with OCPs than Patani and Tiba River, especially p, p’-DDE which was detected in the wide range concentration of 9.6 to 203.1 ng/mL. For oil and grease contamination, Tiba River waters were found to be more polluted than either Patani or Saiburi River. The experimental procedures and analytical results together with the possible sources of OCPs and its environmental impacts are presented.

Enzyme pretreatment of fats, oil and grease from restaurant waste to prolong septic soil treatment system effectiveness.

Science.gov (United States)

Dong, Younsuk; Safferman, Steven I; Ostahowski, Jeff; Herold, Tom; Panter, Ronald

2017-01-02

When a fast-food restaurant's wastewater containing fats, oil and grease (FOG) is discharged into a collection system, it builds up over time and clogs pipes. Similarly, when such wastewater flows into a septic soil treatment system, it adheres to the surface of inlet pipes, gravel/distribution media and soil, restricting the flow and eventually clogging the septic soil treatment system. In this study, an enzymatic pretreatment system was tested on wastewater from a fast-food restaurant to determine its effectiveness in preventing septic soil treatment system clogging. This system used aeration equipment, baffles and a one-time inoculum that excretes enzymes to reduce the molecular weight and number of double bonds associated with FOG. FOG containing triglycerides having lower molecular weights and fewer double bonds are less sticky. The enzymatic pretreatment system was found to cause these changes as verified by measuring the types of triglycerides (compounds in FOG) using liquid chromatography/mass spectrometry. A unique bench-scale septic soil treatment system (soil trench) was also used. Each contained six soil moisture sensors to enable the determination of moisture saturation trends among the five tested conditions: sanitary wastewater only, a combination of sanitary and kitchen wastewater, enzymatically pretreated sanitary and kitchen wastewater, kitchen wastewater, and enzymatically pretreated kitchen wastewater. For all influent types, a significant amount of FOG and other pollutants were removed, regardless of the initial concentrations. Moisture sensor readings showed differences among the tested conditions, indicating that septic soil treatment system clogging was delayed. Inspection of the influent pipe and gravel at the end of testing verified these differences as did the measurements of volatile solids.

Etude du point critique des paliers lisses alimentés à la graisse Study of Critical Point on Plain Bearings Lubricated by Grease

Directory of Open Access Journals (Sweden)

Delneuville P.

2006-11-01

Full Text Available Cet article est essentiellement consacré à l'étude du fonctionnement limite des paliers lisses lubrifiés à la graisse ; son but est de permettre la détermination des conditions nécessaires à l'obtention d'un film lubrifiant d'épaisseur suffisante. L'auteur cherche à cette occasion une loi théorique qui permet de départager les régimes de lubrification, non plus empiriquement, mais sur la base de lois statistiques. La formulation finale doit permettre aux utilisateurs de situer correctement les conditions de fonctionnement d'un palier lisse et d'en estimer la sécurité du régime. This article deals essentially with the boundary behaviour of plain bearings lubricated by grease. Its aim is to determine the conditions required to obtain a sufficiently thick lubricating film. The author proposes a theoretical law for separating lubrication types. This law is not empirical but is based on statistical laws. The final formulation should enable users to correctly situate the operating conditions of a plain bearing and to evaluate the safety factor during running.

Robin Hood Gardens: una interpretación desde el pensamiento topográfico de los Limites Romani

Directory of Open Access Journals (Sweden)

David Casino

2014-02-01

Full Text Available El estrecho vínculo con el territorio que poseían los Limites Romani demostraba, según Alison Smithson, un profundo “pensamiento topográfico”: un compromiso con el lugar basado en un posicionamiento estratégico en el paisaje, una constante adaptación a las condiciones cambiantes del terreno y un intenso modelado de la superficie del suelo. Aspectos fundamentales de estas fortificaciones fronterizas romanas cuya esencia podemos identificar en algunos proyectos clave de Alison y Peter Smithson. Proyectos enraizados que centraban su atención en el plano del suelo, en articular el contacto de los edificios con el terreno y en configurar sus espacios exteriores. Entre estos, los Robin Hood Gardens mostraban de un modo elocuente la fascinación que sentían los Smithson por la condición topográfica de aquellas obras de ingeniería romana. Un interés que les llevaría a explorar conceptos como “límite” y “protección”, así como a recuperar el conjunto de alteraciones topográficas defensivas convirtiéndolas —despojadas de su naturaleza militar— en operaciones clave para radicar en el lugar (del latín radicare: echar raíces, enraizar: una sofisticada apropiación que gravitó “de la defensa al enraizamiento”

Effects of choice white grease or poultry fat on growth performance, carcass leanness, and meat quality characteristics of growing-finishing pigs.

Science.gov (United States)

Engel, J J; Smith, J W; Unruh, J A; Goodband, R D; O'Quinn, P R; Tokach, M D; Nelssen, J L

2001-06-01

Eighty-four crossbred gilts were used to evaluate the effects of dietary choice white grease (CWG) or poultry fat (PF) on growth performance, carcass characteristics, and quality characteristics of longissimus muscle (LM), belly, and bacon of growing-finishing pigs. Pigs (initially 60 kg) were fed a control diet with no added fat or diets containing 2, 4, or 6% CWG or PF. Diets were fed from 60 to 110 kg and contained 2.26 g lysine/Mcal ME. Data were analyzed as a 2 x 3 factorial plus a control with main effects of fat source (CWG and PF) and fat level (2, 4, and 6%). Pigs fed the control diet, 2% fat, and 4% fat had greater (P 0.05) were observed for ADG, dressing percentage, leaf fat weight, LM pH, backfat depth, LM area, percentage lean, LM visual evaluation, LM waterholding capacity, Warner-Bratzler shear and sensory evaluation of the LM and bacon, fat color and firmness measurements, or bacon processing characteristics. Adding dietary fat improved G/F and altered the fatty acid profiles of the LM and bacon, but differences in growth rate, carcass characteristics, and quality and sensory characteristics of the LM and bacon were minimal. Dietary additions of up to 6% CWG or PF can be made with little effect on quality of pork LM, belly, or bacon.

Oil and grease (O&G removal from commercial kitchen waste water using carbonised grass as a key media

Directory of Open Access Journals (Sweden)

Rahmat Siti Nazahiyah

2017-01-01

Full Text Available Oil and grease (O&G are usually found in kitchen waste water. O&G are poorly soluble in water and can cause serious problems during the wastewater treatment. Adsorption is a fundamental process in the treatment of kitchen waste water and very economical. Activated carbon is the most effective adsorbent for this application. Therefore, the aim of the current study is to determine the potential of four materials (i.e. sand, gravel, carbonised grass (CG and clay powder as filter media for O&G removal. The CGs were originated from “Elephant Grass” and it is a fast growing plant with significant potential as carbon. The clay acts as a magnet, drawing the oil molecules out of the water and causing them to attach to the surfaces of the clay. In the current study, two filters were developed with different media materials to get the best percentage removal. Filters 1 and 2 were filled with sand, gravel and CG, and sand, gravel, CG and powder clay, respectively. Three samples were taken during peak hour between April and May 2016. The initial O&G concentration varied from 101.37 mg/l to 248.30 mg/l and the final concentration varied from none to 22.57 mg/l for both filters. The percentage removal (% of O&G were between 90.9 and 97.3 (Filter 1 and between 94.3 and 100 (Filter 2. Overall, both filters could efficiently remove O&G in the waste water and the quality of the carbonised grass proved to be as good as carbon produced from other traditional sources.

Exploiting the igloo principle and greenhouse effect to regulate humidity and temperature

Directory of Open Access Journals (Sweden)

Prabhu Karthick

2006-01-01

Full Text Available Background: Toxic epidermal necrolysis can be fatal and nursing care with careful monitoring of temperature and humidity can improve survival rate. We adapted the greenhouse and igloo principle using a common hood to monitor the temperature and humidity. Methods: A small heater with a regulator was placed in a mini hood and temperature was recorded inside the uncovered hood and hood covered with green cloth and aluminium foil separately. The regular hood was placed over a volunteer and the temperature was measured inside the open hood and hood covered with green cloth and aluminium foil separately. The relative humidity was also monitored using Zeal mercury dry - wet bulb hygrometer. Results: Temperature increase was most marked in the foil-covered hood followed by cloth-covered hood, both with the heater and the volunteer. Similarly, in the volunteer study, the humidity was best maintained inside the aluminium foil-covered hood. Conclusion: We recommend the use of regular hood with suitable cover to monitor the humidity and temperature of patients with toxic epidermal necrolysis.

Studies on the localization of Trypanosoma brucei in the female reproductive tract of bka mice and hooded lister rats

International Nuclear Information System (INIS)

Chipepa, J.A.S.; Brown, H.; Holmes, P.

1991-01-01

A study was conducted to establish whether Trypanosoma brucei migrated preferentially to the reproductive tracts of female BKA mice, or Hooded Lister rats and lodged there as the site of choice compared to other organs. Blood flow to the reproductive tracts, the liver and spleen was measured using red blood cells labelled with chromium- 51. The distribution of trypanosomes labelled with 75 Se-methionine. The average percentage of the blood flow to the reproductive tract was 0.21Plus or minus0.08 in mice, while the mean concentration of trypanosomes there was 0.30% in both mice and rats. Blood flow to the liver was lower than the percentage distribution of Se-labelled T.Brucei(5.17Plus or minus1.34 versus 8.1Plus or Minus1.2). There were, on the contrary, less labelled trypanosomes as compared to the mean blood flow to the spleen (0.54% plus or minus0.18 versus 2.10%pPlus or minus0.88). After 24 hours there were adequate numbers of T. brucei in the reproductive tract to cause parasitaemia in recipient mice. From these preliminary data it was concluded that T. brucei did not lodge in the reproductive organ system a site of choice. (author). 9 refs., 3 tabs

Modeling the impact of watershed management policies on marine ecosystem services with application to Hood Canal, WA, USA

Science.gov (United States)

Sutherland, D. A.; Kim, C.; Marsik, M.; Spiridonov, G.; Toft, J.; Ruckelshaus, M.; Guerry, A.; Plummer, M.

2011-12-01

Humans obtain numerous benefits from marine ecosystems, including fish to eat; mitigation of storm damage; nutrient and water cycling and primary production; and cultural, aesthetic and recreational values. However, managing these benefits, or ecosystem services, in the marine world relies on an integrated approach that accounts for both marine and watershed activities. Here we present the results of a set of simple, physically-based, and spatially-explicit models that quantify the effects of terrestrial activities on marine ecosystem services. Specifically, we model the circulation and water quality of Hood Canal, WA, USA, a fjord system in Puget Sound where multiple human uses of the nearshore ecosystem (e.g., shellfish aquaculture, recreational Dungeness crab and shellfish harvest) can be compromised when water quality is poor (e.g., hypoxia, excessive non-point source pollution). Linked to the estuarine water quality model is a terrestrial hydrology model that simulates streamflow and nutrient loading, so land cover and climate changes in watersheds can be reflected in the marine environment. In addition, a shellfish aquaculture model is linked to the water quality model to test the sensitivity of the ecosystem service and its value to both terrestrial and marine activities. The modeling framework is general and will be publicly available, allowing easy comparisons of watershed impacts on marine ecosystem services across multiple scales and regions.

Metabolic activity in striate and extrastriate cortex in the hooded rat: contralateral and ipsilateral eye input

International Nuclear Information System (INIS)

Thurlow, G.A.; Cooper, R.M.

1988-01-01

The extent of changes in glucose metabolism resulting from ipsilateral and contralateral eye activity in the posterior cortex of the hooded rat was demonstrated by means of the C-14 2-deoxyglucose autoradiographic technique. By stimulating one eye with square wave gratings and eliminating efferent activation from the other by means of enucleation or intraocular TTX injection, differences between ipsilaterally and contralaterally based visual activity in the two hemispheres were maximized. Carbon-14 levels in layer IV of autoradiographs of coronal sections were measured and combined across sections to form right and left matrices of posterior cortex metabolic activity. A difference matrix, formed by subtracting the metabolic activity matrix of cortex contralateral to the stimulated eye from the ipsilateral depressed matrix, emphasized those parts of the visual cortex that received monocular visual input. The demarcation of striate cortex by means of cholinesterase stain and the examination of autoradiographs from sections cut tangential to the cortical surface aided in the interpretation of the difference matrices. In striate cortex, differences were maximal in the medial monocular portion, and the lateral or binocular portion was shown to be divided metabolically into a far lateral contralaterally dominant strip along the cortical representation of the vertical meridian, and a more medial region of patches of more or less contralaterally dominant binocular input. Lateral peristriate differences were less than those of striate cortex, and regions of greater and lesser monocular input could be distinguished. We did not detect differences between the two hemispheres in either anterior or medial peristriate areas

Local exhaust ventilation for the control of welding fumes in the construction industry--a literature review.

Science.gov (United States)

Flynn, Michael R; Susi, Pam

2012-08-01

Arc welding is a common unit operation in the construction industry, where frequent changes in location and welding position make it more difficult to control fume exposures than in industries where fixed locations are the norm. Welders may be exposed to a variety of toxic airborne contaminants including manganese (Mn) and hexavalent chromium (CrVI). Local exhaust ventilation (LEV) is a well-known engineering control for welding fumes but has not been adopted widely in the construction industry. This literature review presents data on the performance of a variety of LEV systems for welding fume control from the construction (five references), shipyard (five references), and other industries. The studies indicate that LEV can reduce fume exposures to total particulate, Mn, and CrVI to levels below currently relevant standards. Field studies suggest that 40-50% or more reduction in exposure is possible with portable or fixed LEV systems relative to natural ventilation but that correct positioning of the hood and adequate exhaust flow rates are essential. Successful implementation of extraction guns for gas metal arc welding (GMAW) and flux core arc welding has been demonstrated, indicating that a successful balance between extraction airflow and shielding gas requirements is possible. Work practices are an important part of achieving successful control of fume exposures; in particular, positioning the hood close to the arc, checking exhaust flow rates, and avoiding the plume. Further research is needed on hood size effects for controlling welding fume with portable LEV systems and identifying and overcoming barriers to LEV use in construction.

Influência de sistemas de plantio e armadilha adesiva na incidência de Frankliniella williamsi Hood na cultura do milho = Influence of planting systems and adhesive trap on the incidence of Frankliniella williamsi Hood in crop maize

Directory of Open Access Journals (Sweden)

Fernando Alves de Albuquerque

2006-07-01

Full Text Available Esta pesquisa objetivou avaliar a influência de diferentes sistemas de plantio de milho e o efeito de armadilha adesiva na incidência de Frankliniella williamsi Hood. Os tratamentos consistiram no plantio direto do milho sobre aveia dessecada com glyphosate, aveia tombada, aveia roçada e plantas daninhas, aveia incorporada e plantio convencional. Alguns tratamentos foram associados a armadilha adesiva de coloração azul, colocada horizontalmente no centro da parcela. Verificou-se que tanto a presença de armadilha quanto os diferentes sistemas de plantio influíram significativamente na infestação das plantas de milho pelo tripes, sendo que os tratamentos “aveia dessecada” e “aveia roçada e plantas daninhas” apresentaram menor incidência do inseto, com esse efeito diminuindo com o desenvolvimento das plantas.This research aimed to evaluate the influence of different systems of corn planting and the effect of adhesive trap on the incidence ofFrankliniella williamsi. The treatments consisted of sowing the corn seed directly on oats dried by glyphosate, tilt oats, cut oats and weeds, incorporated oats, and also conventional planting. Some treatments were associated with adhesive trap of blue coloration, puthorizontally in the center of the plot. Results showed that the presence of traps, as well as the different planting systems influenced significantly on the thrips infestation, and the treatmentswith "dry oats" and "cut oats and weeds" presented smaller incidence of the insect with a decreasing effect along the plants growth.

Age-specific survival of male golden-cheeked warblers on the Fort Hood Military Reservation, Texas

Science.gov (United States)

Duarte, Adam; Hines, James E.; Nichols, James D.; Hatfield, Jeffrey S.; Weckerly, Floyd W.

2014-01-01

Population models are essential components of large-scale conservation and management plans for the federally endangered Golden-cheeked Warbler (Setophaga chrysoparia; hereafter GCWA). However, existing models are based on vital rate estimates calculated using relatively small data sets that are now more than a decade old. We estimated more current, precise adult and juvenile apparent survival (Φ) probabilities and their associated variances for male GCWAs. In addition to providing estimates for use in population modeling, we tested hypotheses about spatial and temporal variation in Φ. We assessed whether a linear trend in Φ or a change in the overall mean Φ corresponded to an observed increase in GCWA abundance during 1992-2000 and if Φ varied among study plots. To accomplish these objectives, we analyzed long-term GCWA capture-resight data from 1992 through 2011, collected across seven study plots on the Fort Hood Military Reservation using a Cormack-Jolly-Seber model structure within program MARK. We also estimated Φ process and sampling variances using a variance-components approach. Our results did not provide evidence of site-specific variation in adult Φ on the installation. Because of a lack of data, we could not assess whether juvenile Φ varied spatially. We did not detect a strong temporal association between GCWA abundance and Φ. Mean estimates of Φ for adult and juvenile male GCWAs for all years analyzed were 0.47 with a process variance of 0.0120 and a sampling variance of 0.0113 and 0.28 with a process variance of 0.0076 and a sampling variance of 0.0149, respectively. Although juvenile Φ did not differ greatly from previous estimates, our adult Φ estimate suggests previous GCWA population models were overly optimistic with respect to adult survival. These updated Φ probabilities and their associated variances will be incorporated into new population models to assist with GCWA conservation decision making.

Effects of ultrasonic and thermo-chemical pre-treatments on methane production from fat, oil and grease (FOG) and synthetic kitchen waste (KW) in anaerobic co-digestion.

Science.gov (United States)

Li, Chenxi; Champagne, Pascale; Anderson, Bruce C

2013-02-01

The effects of ultrasonic and thermo-chemical pre-treatments on the methane production potential of anaerobic co-digestion with synthetic kitchen waste (KW) or fat, oil and grease (FOG) were investigated. Non-linear regressions were fitted to accurately assess and compare the methane production from co-digestion under the various pre-treatment conditions and to achieve representative simulations and predictions. Ultrasonic pre-treatment was not found to improve methane production effectively from either FOG co-digestion or KW co-digestions. Thermo-chemical pre-treatment could increase methane production yields from both FOG and KW co-digestions. COD solubilization was found to effectively represent the effects of pre-treatment. A comprehensive evaluation indicated that the thermo-chemical pre-treatments of pH=10, 55°C and pH=8, 55°C provided the best conditions to increase methane production from FOG and KW co-digestions, respectively. The most effective enhancement of biogas production (288±0.85mLCH(4)/g TVS) was achieved from thermo-chemically pre-treated FOG co-digestion, which was 9.9±1.5% higher than FOG co-digestion without thermo-chemical pre-treatment. Copyright © 2012 Elsevier Ltd. All rights reserved.

Histopathological effect and stress response of mantle proteome following TBT exposure in the Hooded oyster Saccostrea cucullata.

Science.gov (United States)

Khondee, Phattirapa; Srisomsap, Chantragan; Chokchaichamnankit, Daranee; Svasti, Jisnuson; Simpson, Richard J; Kingtong, Sutin

2016-11-01

Tributyltin (TBT), an environmental pollutant in marine ecosystems, is toxic to organisms. Although contamination by and bioaccumulation and toxicity of this compound have been widely reported, its underlying molecular mechanisms remain unclear. In the present study, we exposed the Hooded oyster Saccostrea cucullata to TBT to investigate histopathological effects and proteome stress response. Animals were exposed to three TBT sub-lethal concentrations, 10, 50 and 150 μg/l for 48 h. TBT produced stress leading to histopathological changes in oyster tissues including mantle, gill, stomach and digestive diverticula. TBT induced mucocyte production in epithelia and hemocyte aggregation in connective tissue. Cell necrosis occurred when exposure dosages were high. Comparative proteome analyses of mantle protein of oysters exposed to 10 μg/l and control animals were analyzed by a 2-DE based proteomic approach. In total, 32 protein spots were found to differ (p TBT induced the expression of proteins involved in defensive mechanisms (HSP-78, HSP-70, aldehyde dehydrogenase and catalase), calcium homeostasis (VDAC-3), cytoskeleton and cytoskeleton-associated proteins, energy metabolism and amino acid metabolism. Our study revealed that TBT disturbs calcium homeostasis via VDAC-3 protein in mantle and this probably is the key molecular mechanism of TBT acting to distort shell calcification. Moreover, proteins involved in cell structure (tubulin-alpha and tubulin-beta) and protein synthesis were reduced after TBT exposure. Additionally, differential proteins obtained from this work will be useful as potential TBT biomarkers. Copyright © 2016 Elsevier Ltd. All rights reserved.

Improvements in or relating to glove boxes or similar containers

International Nuclear Information System (INIS)

Strong, R.E.; Boyle, K.; Grant, J.

1976-01-01

The glove box described has an extract system that includes a vortex amplifier venting into the system. The main inlet of the vortex amplifier is connected with the containment system and a control inlet is provided in connection with the atmosphere outside the containment system. A variable flow restrictor is provided between the containment system and the extract system, bypassing the vortex amplifier. The arrangement is such that manipulation of a valve is not normally required. The arrangement is not restricted to glove boxes; it can provide an alternative to fume hoods. (U.K.)

Performance and emission analysis on blends of diesel, restaurant yellow grease and n-pentanol in direct-injection diesel engine.

Science.gov (United States)

Ravikumar, J; Saravanan, S

2017-02-01

Yellow grease from restaurants is typically waste cooking oil (WCO) free from suspended food particles with free fatty acid (FFA) content less than 15%. This study proposes an approach to formulate a renewable, eco-friendly fuel by recycling WCO with diesel (D) and n-pentanol (P) to improve fuel-spray characteristics. Three ternary blends (D50-WCO45-P5, D50-WCO40-P10 and D50-WCO30-P20) were selected based on the stability tests and prepared with an objective to substitute diesel by 50% with up to 45% recycled component (WCO) and up to 20% bio-component (n-pentanol) by volume. The fuel properties of these ternary blends were measured and compared. The emission impacts of these blends on a diesel engine were analysed in comparison with diesel and D50-WCO50 (50% of diesel + 50% of WCO) under naturally articulated and EGR (exhaust gas recirculation) approaches. Doping of n-pentanol showed improved fuel properties when compared to D50-WCO50. Viscosity is reduced up to 45%. Cetane number and density were comparable to that of diesel. Addition of n-pentanol to D50-WCO50 presented improved brake specific fuel consumption (BSFC) for all ternary blends. Brake thermal efficiency (BTE) of D50-WCO30-P20 blend is comparable to diesel due to improved atomization. Smoke opacity reduced, HC emissions increased and CO emissions remained unchanged with doping n-pentanol in the WCO. NOx emission increases with increase in n-pentanol and remained lower than diesel and all load conditions. However, NOx can be decreased by up to threefold using EGR. By adopting this approach, WCO can be effectively reused as a clean energy source by negating environmental hazards before and after its use in diesel engines, instead of being dumped into sewers and landfills.

Assessment in hygiene and radiation protection in use of shielded laminar flow hoods; Bilan en matiere d'hygiene et de radioprotection de l'utilisation de hottes blindees a flux laminaire

Energy Technology Data Exchange (ETDEWEB)

Bouquey, C.; Roudaut, M.; Pommier, M.; Lortal, B. [Institut Bergonie, Service de pharmacie, 33 - Bordeaux (France); Cazaux, A.L. [Institut Bergonie, Service de medecine nucleaire, 33 - Bordeaux (France)

2010-07-01

Radiopharmacy Bergonie institute has grown in 2008, on this occasion, shielded enclosures have been changed. The choice fell on new technologies taking into account the problems of radiation protection and bacterial contamination. We chose laminar flow hoods for achieving the prescription of radiopharmaceuticals in an aseptic environment and full automation of samples of the dose of F.D.G.. we have undertaken a review of performance of this material in sterility, radiation protection and reliability. conclusions: we reconcile our need to optimize radiation protection of manipulators while respecting the constraints of health described in the good practices of preparation (G.P.P.). However, a new problem arises, how do manage electronic and computer quickly without service organization be not perturbed. (N.C.)

Challenges for health care providers, parents and patients who face a child hood cancer diagnosis in Zambia.

Science.gov (United States)

Walubita, Mulima; Sikateyo, Bornwell; Zulu, Joseph M

2018-05-02

Zambia is experiencing high prevalence of childhood cancer. However, very few children access and complete treatment for cancer. This study aimed to document the challenges for health care providers, parents and patients who face a child hood cancer diagnosis in Zambia, and their coping strategies. This was an exploratory health facility-based qualitative study that was conducted at a Paediatric oncology ward at referral hospital in Zambia. In-depth individual interviews conducted with fifteen (15) caregivers and seven (7) key informants were analysed using thematic analysis. Several challenges related to managing the childhood cancer diagnosis were recorded. Individual and family challenges were inadequate knowledge on childhood cancer, lack of finances to meet treatment and transport costs as well as long period of hospitalisation that affected women's ability to perform multiple responsibilities. Whereas challenges at community level were inadequate support to address emotional and physical distress and social stigmatisation experienced by caregivers. Health systems issues included inadequate specialised health workers, poor communication among health workers, limited space and beds as well as insufficient supplies such as blood. Cultural related factors were the belief that cancer is a product of witchcraft as well as religious beliefs regarding the role of faith healing in childhood cancer treatment. Coping strategies used by parents/ caregivers included praying to God, material support from organisations and church as well as delaying having another child. Addressing the challenges for health care providers, parents and patients who face a childhood cancer diagnosis may require adopting a systems or an ecological approach that allows developing strategies that simultaneously address challenges related to the individual, family, community, health system and cultural aspects.

Fort Hood Solar Total Energy Project. Volume II. Preliminary design. Part 1. System criteria and design description. Final report

Energy Technology Data Exchange (ETDEWEB)

None,

1979-01-01

This volume documents the preliminary design developed for the Solar Total Energy System to be installed at Fort Hood, Texas. Current system, subsystem, and component designs are described and additional studies which support selection among significant design alternatives are presented. Overall system requirements which form the system design basis are presented. These include program objectives; performance and output load requirements; industrial, statutory, and regulatory standards; and site interface requirements. Material in this section will continue to be issued separately in the Systems Requirements Document and maintained current through revision throughout future phases of the project. Overall system design and detailed subsystem design descriptions are provided. Consideration of operation and maintenance is reflected in discussion of each subsystem design as well as in an integrated overall discussion. Included are the solar collector subsystem; the thermal storage subsystem, the power conversion sybsystem (including electrical generation and distribution); the heating/cooling and domestic hot water subsystems; overall instrumentation and control; and the STES building and physical plant. The design of several subsystems has progressed beyond the preliminary stage; descriptions for such subsystems are therefore provided in more detail than others to provide complete documentation of the work performed. In some cases, preliminary design parameters require specific verificaton in the definitive design phase and are identified in the text. Subsystem descriptions will continue to be issued and revised separately to maintain accuracy during future phases of the project. (WHK)

Age-specific survival of male Golden-cheeked Warblers on the Fort Hood Military Reservation, Texas

Directory of Open Access Journals (Sweden)

Adam Duarte

2014-12-01

Full Text Available Population models are essential components of large-scale conservation and management plans for the federally endangered Golden-cheeked Warbler (Setophaga chrysoparia; hereafter GCWA. However, existing models are based on vital rate estimates calculated using relatively small data sets that are now more than a decade old. We estimated more current, precise adult and juvenile apparent survival (Φ probabilities and their associated variances for male GCWAs. In addition to providing estimates for use in population modeling, we tested hypotheses about spatial and temporal variation in Φ. We assessed whether a linear trend in Φ or a change in the overall mean Φ corresponded to an observed increase in GCWA abundance during 1992-2000 and if Φ varied among study plots. To accomplish these objectives, we analyzed long-term GCWA capture-resight data from 1992 through 2011, collected across seven study plots on the Fort Hood Military Reservation using a Cormack-Jolly-Seber model structure within program MARK. We also estimated Φ process and sampling variances using a variance-components approach. Our results did not provide evidence of site-specific variation in adult Φ on the installation. Because of a lack of data, we could not assess whether juvenile Φ varied spatially. We did not detect a strong temporal association between GCWA abundance and Φ. Mean estimates of Φ for adult and juvenile male GCWAs for all years analyzed were 0.47 with a process variance of 0.0120 and a sampling variance of 0.0113 and 0.28 with a process variance of 0.0076 and a sampling variance of 0.0149, respectively. Although juvenile Φ did not differ greatly from previous estimates, our adult Φ estimate suggests previous GCWA population models were overly optimistic with respect to adult survival. These updated Φ probabilities and their associated variances will be incorporated into new population models to assist with GCWA conservation decision making.

Guidelines for selection of radiological protective head covering

International Nuclear Information System (INIS)

Galloway, G.R. Jr.

1995-08-01

The hood is recognized throughout the nuclear industry as the standard radiological protective head covering for use in radioactively contaminated work environments. As of June 15, 1995, hoods were required for all activities performed in contaminated areas at the Y-12 Plant. The use of hoods had historically been limited to those radiological activities with a high potential for personnel contamination. Due to the large size of many posted contaminated areas at the Y-12 Plant, and compounding safety factors, requirements for the use of hoods are being reevaluated. The purpose of the evaluation is to develop technically sound guidelines for the selection of hoods when prescribing radiological protective head covering. This report presents the guidelines for selection of radiological protective hoods

Evaluation of oil and grease removal by adsorptive polymeric resins in semi-industrial scale: influence of temperature; Avaliacao da remocao de oleos e graxas por resinas polimericas adsorventes em escala semi-industrial: influencia da temperatura

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Luis F.S. de; Silva, Carla M.F. da; Queiros, Yure G.C.; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Laboratorio de Macromoleculas e Coloides na Industria de Petroleo, Rio de Janeiro, RJ (Brazil)], e-mail: elucas@ima.ufrj.br

2011-07-01

The aim of this study was to evaluate the performance of polymeric resins packed in a fixed bed eluted in semi-industrial scale for oil and greases removal disposed in synthetic oily water in different temperature conditions. For this work, columns packed with vinyl and acryl polymer-base were tested and their efficiency of oil removal was evaluated by fluorimetry technique in two different temperatures: 25 and 60 deg C, in a flow rate condition of 200 mL/min. The experimental results were very good: the removal efficiencies were above 98% in both cases. At 60 deg C, the system keep the efficiency for a longer time: no significant loss in the efficiency was observed after eluting 1,000 times of the column bed volume at 25 deg C and 2,000, at 60 deg C. This result characterizes a great potential of application in the industry. (author)

Reductions in dead space ventilation with nasal high flow depend on physiological dead space volume: metabolic hood measurements during sleep in patients with COPD and controls.

Science.gov (United States)

Biselli, Paolo; Fricke, Kathrin; Grote, Ludger; Braun, Andrew T; Kirkness, Jason; Smith, Philip; Schwartz, Alan; Schneider, Hartmut

2018-05-01

Nasal high flow (NHF) reduces minute ventilation and ventilatory loads during sleep but the mechanisms are not clear. We hypothesised NHF reduces ventilation in proportion to physiological but not anatomical dead space.11 subjects (five controls and six chronic obstructive pulmonary disease (COPD) patients) underwent polysomnography with transcutaneous carbon dioxide (CO 2 ) monitoring under a metabolic hood. During stable non-rapid eye movement stage 2 sleep, subjects received NHF (20 L·min -1 ) intermittently for periods of 5-10 min. We measured CO 2 production and calculated dead space ventilation.Controls and COPD patients responded similarly to NHF. NHF reduced minute ventilation (from 5.6±0.4 to 4.8±0.4 L·min -1 ; pspace ventilation (from 2.5±0.4 to 1.6±0.4 L·min -1 ; pspace ventilation correlated with baseline physiological dead space fraction (r 2 =0.36; pspace volume.During sleep, NHF decreases minute ventilation due to an overall reduction in dead space ventilation in proportion to the extent of baseline physiological dead space fraction. Copyright ©ERS 2018.

Development of high performance lubricant through the compatibility of polyalphaolefin, polyurea and irradiated polytetrafluoroethylene; Graxa de poliureia: estudo da compatibilidade da poliureia, polialfaolefina e politetrafluoretileno irradiado para melhoria da lubricidade e estabilidade

Energy Technology Data Exchange (ETDEWEB)

Ratao, Natalia Torres

2013-07-01

Lubricants are gaseous, liquid, semi solid or solid (powder) materials those form a film between two parties preventing friction. High performance lubricants are designed to work under severe conditions of temperature, pressure, and contamination. The most used are liquids (oils) and semi solids (greases). Greases are applied where oils can drain or in inaccessible places and are divided generally into two classes, soap and no soap. The most used non soap grease is polyurea, obtained by the reaction between amine and isocyanate, has highly thixotropic, high dielectric strength and excellent anticorrosive property, so it is widely used for lubrication of electric motors and shipbuilding machinery. For a grease with high performance, in this study was used a synthetic lubricant fluid, polyalphaolefin, and was also employed solid lubricant additive polytetrafluoroethylene (PTFE) due its lowest coefficient of friction, is found commercially irradiated in air to obtain smaller particles and to produce oxygenated terminal groups those are more compatible with the metal surface. The tests conducted were comparatively between pure polyurea grease and with PTFE additive. The characterizations were made by infrared spectroscopy and elemental analysis of C, N and H and Free NCO index, proving the formation of four carbons polyurea (tetraurea). The functional analysis of drop point and oil separation showed high stability and compatibility between the polymers increased when PTFE was added. The excellent resistance of pure tetraurea grease to wear and extreme pressure were demonstrated by four-ball and practical bearings tests, characterizing this grease as a high performance lubricant, when compared to most used greases in the market. (author)

Development of high performance lubricant through the compatibility of polyalphaolefin, polyurea and irradiated polytetrafluoroethylene

International Nuclear Information System (INIS)

Ratao, Natalia Torres

2013-01-01

Lubricants are gaseous, liquid, semi solid or solid (powder) materials those form a film between two parties preventing friction. High performance lubricants are designed to work under severe conditions of temperature, pressure, and contamination. The most used are liquids (oils) and semi solids (greases). Greases are applied where oils can drain or in inaccessible places and are divided generally into two classes, soap and no soap. The most used non soap grease is polyurea, obtained by the reaction between amine and isocyanate, has highly thixotropic, high dielectric strength and excellent anticorrosive property, so it is widely used for lubrication of electric motors and shipbuilding machinery. For a grease with high performance, in this study was used a synthetic lubricant fluid, polyalphaolefin, and was also employed solid lubricant additive polytetrafluoroethylene (PTFE) due its lowest coefficient of friction, is found commercially irradiated in air to obtain smaller particles and to produce oxygenated terminal groups those are more compatible with the metal surface. The tests conducted were comparatively between pure polyurea grease and with PTFE additive. The characterizations were made by infrared spectroscopy and elemental analysis of C, N and H and Free NCO index, proving the formation of four carbons polyurea (tetraurea). The functional analysis of drop point and oil separation showed high stability and compatibility between the polymers increased when PTFE was added. The excellent resistance of pure tetraurea grease to wear and extreme pressure were demonstrated by four-ball and practical bearings tests, characterizing this grease as a high performance lubricant, when compared to most used greases in the market. (author)

Installation dismantling system, working process and hood utilizable in this system

International Nuclear Information System (INIS)

Poirier, J.C.; Mulcey, P.; Morel, P.; Vavasseur, C.

1989-01-01

The system for dismantling an installation under a controlled atmosphere is made by a tool polluting the atmosphere, a gas blanket creating a continement zone around the tool, an extractor removing polluted gas from the zone, a purifier for the extracted gas and a controller regulating the flow of gas in the blanket and keeping the installation at constant pressure [fr

Innovative measures undertaken for improvement of working conditions and equipment's at Quality Control Program (QCP), BRIT

International Nuclear Information System (INIS)

Reddy, B.H.; Jaiswar, N.M.

2009-01-01

Mixing of organic and aqueous phases using suction pumps/suction line available in the fume hoods in lieu of the hand-pump and plastic bellows hitherto used for the purpose of solvent extraction generator for 99m Tc. This minimizes exposure of the personnel to the radiation hazard by reducing the actual physical handling and time of exposure. Use of specially fabricated PVC long handled rod for safe operation of nozzles used in solvent extraction assembly for extraction of 99m Tc from 99 Mo. In the past, direct handling of knobs was the practice which was unsafe with respect to both dose and physical maneuvering between operator and assembly. The working conditions and safe practice in managing radioactive waste are discussed in the paper

Organically modified clay removes oil from water

International Nuclear Information System (INIS)

Alther, G.R.

1995-01-01

When bentonite or other clays and zeolite are modified with quaternary amines, they become organophilic. Such modified bentonites are used to remove mechanically emulsified oil and grease, and other sparingly soluble organics. Types of oil found in water can include fats, lubricants, cutting fluids, heavy hydrocarbons such as tars, grease, crude oil, diesel oils; and light hydrocarbons such as kerosene, jet fuel, and gasoline. If the organoclay is granulated, it is placed into a liquid phase carbon filter vessel to remove FOGs (Free Oil and Grease) and chlorinated hydrocarbons. In this application the clay is mixed with anthrazite to prevent early plugging of the filter by oil or grease droplets. In batch systems a powdered organoclay is employed. Organoclay removes mechanically emulsified oil and grease at 5--7 times the rate of activated carbon, or 50% of its dry weight. Oil and grease and other large sparingly soluble chlorinated hydrocarbons and NOMs (Natural Organic Matter) blind the pores of activated carbon (and ion-exchange resins), reducing its effectiveness significantly. It is therefore economically advantageous for the end user to prepolish the water before it enters carbon vessels. Operating costs can often be reduced by 50% or more

Effect of saponification on the anaerobic digestion of solid fatty residues.

Science.gov (United States)

Mouneimne, A H; Carrère, H; Bernet, N; Delgenès, J P

2003-10-01

In France, fatty residues considered as "non-ultimate" waste will not be accepted in landfill from 2002, in accordance with French legislation. Anaerobic digestion appears as an alternative process to mobilize and profitably use such fermentable waste. In this work, the effect of an alkaline pretreatment on the degradation of hexane extractible matter (HEM) and the production of volatile fatty acids (VFAs) was compared in reactors working at pH 6.5 and 8.5. The results obtained showed that 40% (+/- 0.1) of HEM were degraded at pH 8.5 versus 10% (+/- 0.3) at pH 6.5, regardless of the alkali agent used to saponify the greasy wastes. The highest performances of VFA production (8.45% +/- 0.3) were obtained at pH 8.5 with greases saponified by potassium hydroxide, compared to results (4.25% +/- 0.1) with greasy waste saponified by sodium hydroxide. This difference in VFA production might be attributable to biotoxic molecules generated during the saponification of greases by soda, limiting consequently the VFA production process.

Socioeconomic inequalities in informal payments for health care: An assessment of the 'Robin Hood' hypothesis in 33 African countries.

Science.gov (United States)

Kankeu, Hyacinthe Tchewonpi; Ventelou, Bruno

2016-02-01

In almost all African countries, informal payments are frequently made when accessing health care. Some literature suggests that the informal payment system could lead to quasi-redistribution among patients, with physicians playing a 'Robin Hood' role, subsidizing the poor at the expense of the rich. We empirically tested this assumption with data from the rounds 3 and 5 of the Afrobarometer surveys conducted in 18 and 33 African countries respectively, from 2005 to 2006 for round 3 and from 2011 to 2013 for round 5. In these surveys, nationally representative samples of people aged 18 years or more were randomly selected in each country, with sizes varying between 1048 and 2400 for round 3 and between 1190 and 2407 for round 5. We used the 'normalized' concentration index, the poor/rich gap and the odds ratio to assess the level of inequality in the payment of bribes to access care at the local public health facility and implemented two decomposition techniques to identify the contributors to the observed inequalities. We obtained that: i) the socioeconomic gradient in informal payments is in favor of the rich in almost all countries, indicating a rather regressive system; ii) this is mainly due to the socioeconomic disadvantage itself, to poor/rich differences in supply side factors like lack of medicines, absence of doctors and long waiting times, as well as regional disparities. Although essentially empirical, the paper highlights the need for African health systems to undergo substantial country-specific reforms in order to better protect the worse-off from financial risk when they seek care. Copyright © 2016 Elsevier Ltd. All rights reserved.

Wanted: elbow grease

CERN Document Server

Anaïs Schaeffer

2013-01-01

In Divonne-les-Bains, an association founded by former CERN personnel is restoring the oldest hydroelectric plant in France. The adventure started more than ten years ago, and now you’re invited to take part…   View of the benzole-powered thermic engine from 1907. Georges Leskens, a spritely 85-year-old, is president of the Divonnelectro association. Georges, a former electrical engineer at CERN, now has a new goal: to bring the Moulin David hydroelectric plant in Divonne-les-Bains, which he found in a derelict state in 2001, back to life. “When I entered the plant for the first time, I found several remarkable period machines… and the extent of the damage,” recalls Georges. “Among other things, the town used the building for storing salt and grit for the roads... so I don’t need to tell you what state the mechanisms were in!” Aware of the historical value of the site (see box), Georges convinced the D...

Study on the extraction kinetics of U(IV) extraction with neutral phosphoric extractant

International Nuclear Information System (INIS)

Lin Zhou; Liao Shishu; Li Zhou

1995-04-01

The extraction kinetics of U(IV) in the diisooctyl isobutylphosphonate system has been studied by using the single drop method. The effects of the concentrations of U(IV), HCl and extractant on the extraction rate have been examined. In a certain HCl concentration, the extraction rate equation has been acquired and in the condition of various HCl concentration the extraction rate of U(IV) is proportional to [HCl 1.51 . The effect of operation temperature was also examined, and the calculated apparent activation energy is equal to 23.24 kJ/mol. From the experimental results, the extraction reaction process and the rate-controlling step have been deduced. (4 figs., 5 tabs.)

Comparison of mentha extracts obtained by different extraction methods

Directory of Open Access Journals (Sweden)

Milić Slavica

2006-01-01

Full Text Available The different methods of mentha extraction, such as steam distillation, extraction by methylene chloride (Soxhlet extraction and supercritical fluid extraction (SFE by carbon dioxide (CO J were investigated. SFE by CO, was performed at pressure of 100 bar and temperature of40°C. The extraction yield, as well as qualitative and quantitative composition of obtained extracts, determined by GC-MS method, were compared.

Comparison of acrylic polymer adhesive tapes and silicone optical grease in light sharing detectors for positron emission tomography

Science.gov (United States)

Van Elburg, Devin J.; Noble, Scott D.; Hagey, Simone; Goertzen, Andrew L.

2018-03-01

Optical coupling is an important factor in detector design as it improves optical photon transmission by mitigating internal reflections at light-sharing boundaries. In this work we compare optical coupling materials, namely double-sided acrylic polymer tapes and silicone optical grease (SiG), in the context of positron emission tomography. Four double-sided tapes from 3 M of varying thicknesses (0.229 mm-1.016 mm) and adhesive materials (‘100MP’, ‘A100’, and ‘GPA’) were characterized with spectrophotometer measurements as well as photopeak amplitude and energy resolution measurements using lutetium-yttrium oxy-orthosilicate (LYSO) coupled to photomultiplier tubes (PMT) or silicon photomultipliers (SiPMs). Transmission spectra from the spectrophotometer showed over 80% transmission for all tapes at 420 nm and above, with 89.6% and 88.8% transmission for the 0.508 mm and 1.016 mm thick GPA tapes, respectively, at 420 nm. Measurements with single-pixel LYSO-PMT and 4  ×  4 array (one-to-one coupled) LYSO-SiPM setups determined that SiG had the greatest photopeak amplitude, with tapes showing 2.1%-14.8% reduction in photopeak amplitude with respect to SiG. Energy resolution changed by less than 4% on a relative basis between tapes and SiG with PMT measurements, however for the SiPM array measurements the energy resolution improved from 15.6%  ±  2.7% full-width at half-maximum to 11.4%  ±  1.2% for SiG and 1 mm GPA respectively. Data acquired with dual-layer offset LYSO arrays (light sharing detector designs) demonstrated that a detector coupled with 1 mm thick GPA tape produced equivalent detector flood histograms to those from a design coupled with SiG and a 1 mm thick glass lightguide. No significant degradation in photopeak amplitude and energy resolution was observed over five months of measurements, indicating the tapes maintain their coupling integrity over several months. Though minimal photopeak amplitude

Comparison of acrylic polymer adhesive tapes and silicone optical grease in light sharing detectors for positron emission tomography.

Science.gov (United States)

Van Elburg, Devin J; Noble, Scott D; Hagey, Simone; Goertzen, Andrew L

2018-02-26

Optical coupling is an important factor in detector design as it improves optical photon transmission by mitigating internal reflections at light-sharing boundaries. In this work we compare optical coupling materials, namely double-sided acrylic polymer tapes and silicone optical grease (SiG), in the context of positron emission tomography. Four double-sided tapes from 3 M of varying thicknesses (0.229 mm-1.016 mm) and adhesive materials ('100MP', 'A100', and 'GPA') were characterized with spectrophotometer measurements as well as photopeak amplitude and energy resolution measurements using lutetium-yttrium oxy-orthosilicate (LYSO) coupled to photomultiplier tubes (PMT) or silicon photomultipliers (SiPMs). Transmission spectra from the spectrophotometer showed over 80% transmission for all tapes at 420 nm and above, with 89.6% and 88.8% transmission for the 0.508 mm and 1.016 mm thick GPA tapes, respectively, at 420 nm. Measurements with single-pixel LYSO-PMT and 4  ×  4 array (one-to-one coupled) LYSO-SiPM setups determined that SiG had the greatest photopeak amplitude, with tapes showing 2.1%-14.8% reduction in photopeak amplitude with respect to SiG. Energy resolution changed by less than 4% on a relative basis between tapes and SiG with PMT measurements, however for the SiPM array measurements the energy resolution improved from 15.6%  ±  2.7% full-width at half-maximum to 11.4%  ±  1.2% for SiG and 1 mm GPA respectively. Data acquired with dual-layer offset LYSO arrays (light sharing detector designs) demonstrated that a detector coupled with 1 mm thick GPA tape produced equivalent detector flood histograms to those from a design coupled with SiG and a 1 mm thick glass lightguide. No significant degradation in photopeak amplitude and energy resolution was observed over five months of measurements, indicating the tapes maintain their coupling integrity over several months. Though minimal photopeak amplitude degradation

Feasibility Study of Economics and Performance of Solar Photovoltaics at the Ft. Hood Military Base Outside Killeen, Texas. A Study Prepared in Partnership with the Environmental Protection Agency for the RE-Powering America's Land Initiative: Siting Renewable Energy on Potentially Contaminated Land and Mine Sites

Energy Technology Data Exchange (ETDEWEB)

Geiger, J.; Lisell, L.; Mosey, G.

2013-10-01

The U.S. Environmental Protection Agency (EPA), in accordance with the RE-Powering America's Land initiative through the Region 6 contract, selected Ft. Hood Army Base in Killeen, Texas, for a feasibility study of renewable energy production. The National Renewable Energy Laboratory (NREL) provided technical assistance for this project. The purpose of this study is to assess the site for possible photovoltaic (PV) system installations and estimate the cost, performance, and site impacts of different PV options. In addition, the report recommends financing options that could assist in the implementation of a PV system at the site.

Influence of fat and oil type on the yield, physico-chemical properties, and microstructure of fat, oil, and grease (FOG) deposits.

Science.gov (United States)

Del Mundo, Dann Marie N; Sutheerawattananonda, Manote

2017-11-01

Fat, oil, and grease (FOG) deposit, in the form of calcium soap, was found to cause sanitary sewer overflows due to its adhesion on pipe walls. To address this problem, laboratory-prepared calcium soaps have been used to investigate the formation mechanisms of FOG deposits. However, the fats and oils previously utilized were limited and some soap characteristics were not examined. This research attempted to probe through the properties of calcium soaps prepared from calcium chloride and the fats and oils of chicken, pork, palm olein, soybean, olive, and coconut to further understand FOG formation and stability. Results revealed that FOG deposits may occur as smooth, paste-like material or coarse, semi-solid substance depending on their exposure to excess fat/oil and calcium. The smooth soaps with more excess fat/oil demonstrated high apparent viscosity and consistency index, while the coarse soaps with large levels of calcium signified higher melting endset. Moreover, a soap microstructure showing evident networks and lesser void area displayed higher heat and rheological stability, respectively. Overall, fats and oils with higher oleic to palmitic acid ratio such as palm olein oil, olive oil, chicken fat, and pork fat produced soaps with greater yield and degree of saponification. Hence, establishments and authorities should be alert in managing and monitoring these wastes. On the other hand, soybean oil high in linoleic acid and coconut oil high in lauric acid do not pose an immediate threat to the sewer system since they only produced soaps in small quantity. However, their soaps showed high melting endset which could pose a serious effect when accumulated at large amount. On the whole, the fatty acid profile of fats and oils, the presence of excess fat/oil, and calcium content mainly dictate the appearance, melting, rheology, and microstructure of calcium soaps. Their distinct properties can be used as criteria in predicting the condition and stability of FOG

Direct observation of lubricant additives using tomography techniques

Energy Technology Data Exchange (ETDEWEB)

Chen, Yunyun [Department of Materials Science and Engineering, Texas A& M University, College Station, Texas 77843 (United States); Sanchez, Carlos [Mechanical Engineering, Texas A& M University, College Station, Texas 77843 (United States); Parkinson, Dilworth Y. [Advanced Light Source, Lawrence Berkeley National Laboratory, Berkeley, California 94720 (United States); Liang, Hong, E-mail: hliang@tamu.edu [Department of Materials Science and Engineering, Texas A& M University, College Station, Texas 77843 (United States); Mechanical Engineering, Texas A& M University, College Station, Texas 77843 (United States)

2016-07-25

Lubricants play important roles in daily activities such as driving, walking, and cooking. The current understanding of mechanisms of lubrication, particularly in mechanical systems, has been limited by the lack of capability in direct observation. Here, we report an in situ approach to directly observe the motion of additive particles in grease under the influence of shear. Using the K-edge tomography technique, it is possible to detect particular additives in a grease and observe their distribution through 3D visualization. A commercial grease as a reference was studied with and without an inorganic additive of Fe{sub 3}O{sub 4} microparticles. The results showed that it was possible to identify these particles and track their movement. Under a shear stress, Fe{sub 3}O{sub 4} particles were found to adhere to the edge of calcium complex thickeners commonly used in grease. Due to sliding, the grease formed a film with increased density. This approach enables in-line monitoring of a lubricant and future investigation in mechanisms of lubrication.

FTIR spectroscopy measurements and CFD simulations of the pollutants arising from unflued combustion in a room

International Nuclear Information System (INIS)

Chen, J.; Fletcher, D.F.; Haynes, B.S.; Duffy, B.; Nelson, P.

2001-01-01

This paper reports on a study of indoor air quality in a simulated kitchen environment. Combustion products from unflued combustion from a gas cook-top in a ventilated room were measured using an extractive FTIR technique. Results were compared with those from conventional instruments and the FTIR technique was shown to give good agreement. Detection limits and the effects of H 2 O and CO 2 in obscuring the spectrum were studied. In addition, Computational Fluid Dynamics (CFD) was used to explore the conditions in the room and to assist with experimental design. This revealed a complex flow situation that can arise when the plume from the cook top interacts with the extraction hood. (Author)

WASTE GAS COMPUTER SIMULATION OF BOF CONVERTES PRIMARY GAS DEDUSTING SYSTEMS OF ARCELORMITTAL TUBARÃO

Directory of Open Access Journals (Sweden)

Rafael Sartim

2012-06-01

Full Text Available tract A numerical simulation to simulate the fluid flow inside a BOF hood of the ArcelorMittal Tubarão converters is performed. Motivated by the historical failure due to wear in the walls of the hood the objective of the present work is to understand the flow structure, so that it can reduce wear rates. For this study a Computational Fluid Dynamics software ANSYS CFX II is used. The results show that there are basically two mechanisms of wear in the hoods: (i erosion due the projection of the particulate material at high speed in the posterior wall of the output curve of the hood; (ii abrasion due the falling down of the heavier particulate in the opposite direction to the flow in the region of low speed in the slope of the hood

The Swartkops estuary

CSIR Research Space (South Africa)

Baird, D

1988-01-01

Full Text Available AND CHEMICAL DATA FOR CRUDE WOOL GREASE' Colour Density (at 15T) Refractive index (40°C) Melting point Free acid content Free alcohol content Iodine value Saponification value Molecular weight Proportion of fatty acids Proportion of alcohols Acids..., sparingly soluble in alcohol and freely soluble in ether and chloroform. Truter' published some physical and chemical data relating to crude wool grease as given in Table 1. Essentially wool grease is a complex mixture of high molecular weight esters...

Solvent extraction

Energy Technology Data Exchange (ETDEWEB)

Coombs, D.M.; Latimer, E.G.

1988-01-05

It is an object of this invention to provide for the demetallization and general upgrading of heavy oil via a solvent extracton process, and to improve the efficiency of solvent extraction operations. The yield and demetallization of product oil form heavy high-metal content oil is maximized by solvent extractions which employ either or all of the following techniques: premixing of a minor amount of the solvent with feed and using countercurrent flow for the remaining solvent; use of certain solvent/free ratios; use of segmental baffle tray extraction column internals and the proper extraction column residence time. The solvent premix/countercurrent flow feature of the invention substantially improves extractions where temperatures and pressures above the critical point of the solvent are used. By using this technique, a greater yield of extract oil can be obtained at the same metals content or a lower metals-containing extract oil product can be obtained at the same yield. Furthermore, the premixing of part of the solvent with the feed before countercurrent extraction gives high extract oil yields and high quality demetallization. The solvent/feed ratio features of the invention substanially lower the captial and operating costs for such processes while not suffering a loss in selectivity for metals rejection. The column internals and rsidence time features of the invention further improve the extractor metals rejection at a constant yield or allow for an increase in extract oil yield at a constant extract oil metals content. 13 figs., 3 tabs.

The method for simultaneous extraction and back extraction in liquid three-phase system and equipment for simultaneous extraction and back extraction in liquid three-phase system

International Nuclear Information System (INIS)

Palyska, W.; Chmielewski, A.G.

1992-01-01

The method for simultaneous extraction and back extraction in liquid three-phase system has been worked out. The equipment designed for that process has been also subject of the patent. The interesting component is extracted first to intermediate phase consists of magnetic solvent keeping two extracting phases separately. The intermediate magnetic liquid has been kept in its position using a stable magnet maintained on the surface of the extraction vessel. Then the component pass from intermediate phase to the third phase as a result of back extraction. Mixing in the extraction and back extraction zones is organized by means of rotating shaft going along the whole apparatus. The extraction and back extraction processes occur simultaneously as a result of continuous flow of solvent in their zones. The single extraction back extraction facilities can be joined in larger batteries. 3 figs

Simulation of optical configurations and signal processing methods in Anger-type neutron-position scintillation detector

International Nuclear Information System (INIS)

Roche, C.T.; Strauss, M.G.; Brenner, R.

1984-01-01

The spatial linearity and resolution of Anger-type neutron-position scintillation detectors are studied using a semi-empirical model. Detector optics with either an air gap or optical grease between the scintillator and the dispersive light guide are considered. Three signal processing methods which truncate signals from PMT's distant from the scintillation are compared with the linear resistive weighting method. Air gap optics yields a 15% improvement in spatial resolution and 50% reduction in differential and integral nonlinearity relative to grease coupled optics, using linear processing. Using signal truncation instead of linear processing improves the resolution 15-20% for the air gap and 20-30% for the grease coupling case. Thus, the initial discrepancy in the resolution between the two optics nearly vanished, however the linearity of the grease coupled system is still significantly poorer

Detection of TRPV4 channel current-like activity in Fawn Hooded hypertensive (FHH rat cerebral arterial muscle cells.

Directory of Open Access Journals (Sweden)

Debebe Gebremedhin

Full Text Available The transient receptor potential vallinoid type 4 (TRPV4 is a calcium entry channel known to modulate vascular function by mediating endothelium-dependent vasodilation. The present study investigated if isolated cerebral arterial myocytes of the Fawn Hooded hypertensive (FHH rat, known to display exaggerated KCa channel current activity and impaired myogenic tone, express TRPV4 channels at the transcript and protein level and exhibit TRPV4-like single-channel cationic current activity. Reverse transcription polymerase chain reaction (RT-PCR, Western blot, and immunostaining analysis detected the expression of mRNA transcript and translated protein of TRPV4 channel in FHH rat cerebral arterial myocytes. Patch clamp recording of single-channel current activity identified the presence of a single-channel cationic current with unitary conductance of ~85 pS and ~96 pS at hyperpolarizing and depolarizing potentials, respectively, that was inhibited by the TRPV4 channel antagonist RN 1734 or HC 067074 and activated by the potent TRPV4 channel agonist GSK1016790A. Application of negative pressure via the interior of the patch pipette increased the NPo of the TRPV4-like single-channel cationic current recorded in cell-attached patches at a patch potential of 60 mV that was inhibited by prior application of the TRPV4 channel antagonist RN 1734 or HC 067047. Treatment with the TRPV4 channel agonist GSK1016790A caused concentration-dependent increase in the NPo of KCa single-channel current recorded in cell-attached patches of cerebral arterial myocytes at a patch potential of 40 mV, which was not influenced by pretreatment with the voltage-gated L-type Ca2+ channel blocker nifedipine or the T-type Ca2+ channel blocker Ni2+. These findings demonstrate that FHH rat cerebral arterial myocytes express mRNA transcript and translated protein for TRPV4 channel and display TRPV4-like single-channel cationic current activity that was stretch-sensitive and

Ultrasound-Assisted Extraction: Effect of Extraction Time and Solvent ...

African Journals Online (AJOL)

Purpose: To investigate the influence of extraction conditions assisted by ultrasound on the quality of extracts obtained from Mesembryanthemum edule shoots. Methods: The extraction procedure was carried out in an ultrasonic bath. The effect of two solvents (methanol and ethanol) and two extraction times (5 and 10 min) ...

Extraction method

International Nuclear Information System (INIS)

Stary, J.; Kyrs, M.; Navratil, J.; Havelka, S.; Hala, J.

1975-01-01

Definitions of the basic terms and of relations are given and the knowledge is described of the possibilities of the extraction of elements, oxides, covalent-bound halogenides and heteropolyacids. Greatest attention is devoted to the detailed analysis of the extraction of chelates and ion associates using diverse agents. For both types of compounds detailed conditions are given of the separation and the effects of the individual factors are listed. Attention is also devoted to extractions using mixtures of organic agents, the synergic effects thereof, and to extractions in non-aqueous solvents. The effects of radiation on extraction and the main types of apparatus used for extractions carried out in the laboratory are described. (L.K.)

Accelerated Solvent Extraction: An Innovative Sample Extraction Technique for Natural Products

International Nuclear Information System (INIS)

Hazlina Ahmad Hassali; Azfar Hanif Abd Aziz; Rosniza Razali

2015-01-01

Accelerated solvent extraction (ASE) is one of the novel techniques that have been developed for the extraction of phytochemicals from plants in order to shorten the extraction time, decrease the solvent consumption, increase the extraction yield and enhance the quality of extracts. This technique combines elevated temperatures and pressure with liquid solvents. This paper gives a brief overview of accelerated solvent extraction technique for sample preparation and its application to the extraction of natural products. Through practical examples, the effects of operational parameters such as temperature, volume of solvent used, extraction time and extraction yields on the performance of ASE are discussed. It is demonstrated that ASE technique allows reduced solvent consumption and shorter extraction time, while the extraction yields are even higher than those obtained with conventional methods. (author)

Extraction process

International Nuclear Information System (INIS)

Rendall, J.S.; Cahalan, M.J.

1979-01-01

A process is described for extracting at least two desired constituents from a mineral, using a liquid reagent which produces the constituents, or compounds thereof, in separable form and independently extracting those constituents, or compounds. The process is especially valuable for the extraction of phosphoric acid and metal values from acidulated phosphate rock, the slurry being contacted with selective extractants for phosphoric acid and metal (e.g. uranium) values. In an example, uranium values are oxidized to uranyl form and extracted using an ion exchange resin. (U.K.)

Risco de intoxicação profissional por tricloroetileno em processos de desengraxamento no município de São Paulo, Brasil Risk of occupational intoxication due to trichloroethvlene in grease removal operations in the county of S. Paulo, Brazil

Directory of Open Access Journals (Sweden)

Herbert M. A. Stettiner

1977-09-01

Full Text Available A toxicidade de vapores de tricloroetileno (TRI em locais de trabalho é posta em evidência. Determinou-se a concentração de vapores de TRI no ar em fábricas e oficinas onde o líquido serve para desengraxar peças metálicas. Os metabólitos do TRI, o ácido tricloroacético e o tricloroetanol foram determinados em urina de pessoas expostas. Os resultados destas determinações permitem ver a periculosidade potencial que o uso do TRI apresenta.The toxic effects of trichloroethylene (TRI vapors are explained. The TRI vapors have been determined in the air of workingplaces where the liquid is used to remove oil and grease from metal surfaces. Its metabolites, tricehorocetic acid and trichloroethanol have been determined in the urine of exposed persons. The TRI vapors concentrations and urinary TCA resuts confirm the potential danger represented by the use of trichloroethylene in decreasing processes.

Development of high performance lubricant through the compatibilization of polyalphaolefin, polyurea and irradiated polytetrafluoroethylene

International Nuclear Information System (INIS)

Ratao, Natalia T.; Zen, Heloisa A.; Lugao, Ademar B.

2013-01-01

High performance lubricants are essential for shipping and oil exploration industries for working under severe conditions of temperature, pressure and contamination. Polytetrafluoroethylene (PTFE) is widely used as a lubricating additive in greases for presenting the lowest known coefficient of friction, is commercially found irradiated in air, by this way can be grinded and oxygenated terminal groups can be formed. PTFE processed by ionizing radiation with 4μ average particle size was supplied by Uniflon and compared with the ultraviolet-irradiated PTFE with the same average particle size, from Dupont. The characterization of functional proprieties by drop point, oil separation and four ball test was conducted with a polyurea base grease additive with both types of PTFE. The chemical characterization was done with Differential Scanning Calorimetry (DSC). The drop point and oil separation tests showed that the Uniflon irradiated PTFE improved the thermal resistance and stability of polyurea grease due to the greater presence of the end groups increase the compatibility of the additive with the fluid. Four ball tests showed that the grease with Uniflon irradiated PTFE also has a better antiwear and extreme pressure performance because of the greater polarity of the molecules improving the dispersion and anchoring of the PTFE in metal surface voids, reducing wear. The PTFE processed by ionizing radiation showed greater compatibility with polyurea grease and polyalphaolefin fluid and the grease functional characteristics met the requirements for a high performance lubricant. (author)

Adult orthodontic therapy: extraction versus non-extraction.

Science.gov (United States)

Baumrind, S

1998-11-01

This study addresses the problem of randomization of subjects with respect to an irreversible aspect of treatment strategy, namely, the extraction of teeth. The investigation includes both prospective and retrospective components. The data presented focus on clinician decision-making. Of the 1321 potential subjects for whom records were taken, 250 met the inclusion criteria. Of these subjects, 82 declined to participate and 20 were dropped because of difficulty in obtaining five independent evaluations of their records within a reasonable time frame. Thus, the final sample contained 148 subjects. Approximately one-third of the subjects in the sample are adult, somewhat more than half are female, and Class I malocclusions outnumber Class II malocclusions by a count of 95 to 53. Patterns of agreement and disagreement among five clinicians include: a) agreement/disagreement on the primary decision whether or not to extract: the data reveal a strong tendency towards consensus among the clinicians; b) agreement/disagreement on extraction pattern in patients in whom the clinician believes that extraction is indicated: the clinicians tended strongly to agree on extraction pattern; c) agreement/disagreement on the need for adjunctive orthognathic surgery: decisions favoring surgery were more common and more 'definite' than 'probable' in the adult cohort than in the adolescent cohort but this tendency was not as strong as had been anticipated; d) agreement/disagreement concerning Angle classification: disagreements were more common than had been anticipated; and e) differences among the individual clinicians as to their ratios of extraction/non-extraction decisions: overall, clinicians opted for extraction less frequently in the adolescent cohort than in the adult cohort (55 vs. 66%). Because the data are drawn from actual clinical experience, the conclusions involve a number of assumptions and their generalizability should be evaluated.

Quality Parameters of Curcuma Longa L. Extracts by Supercritical Fluid Extraction (SFE) and Ultrasonic Assisted Extraction (UAE)

International Nuclear Information System (INIS)

Zaibunnisa Abdul Haiyee; Siti Hafsah Mohd Shah; Khudzir Ismail; Nooraain Hashim; Wan Iryani Wan Ismail

2016-01-01

Turmeric is one of the prominently use herbal plants due to its diverse beneficial effects especially in Indian medicine. The rhizome part of the turmeric contains valuable compounds which have been said to owe its antimicrobial effects, anti-cancer, anti-inflammatory and enhance wound healing. Due to its short-life span and perishable properties, the conversion of the rhizome into turmeric extract is desirable. Several methods have been used for extraction such as Soxhlet extraction and pressurized liquid extraction (PLE). However, these techniques are tedious, laborious, time consuming and involves the usage of toxic organic solvent, of which safeness of the end product is doubtful. In this study, a rapid, reliable and green extraction method of supercritical fluid extraction (SFE) and ultrasonic assisted extraction (UAE) were used. SFE without modifier has resulted in 0.0006 mg/ 100 g of curcuminoids concentration and 5.62 % of yield (dry weight basis). UAE using ethanol was able to produce significantly the highest yield (6.40 %, dry weight basis) and the highest curcuminoids concentration (0.1020 mg/ 100 g). However, SFE was able to produce extract that contain significantly higher major volatile compounds; tumerone, ar-turmerone and curlone. Therefore, this study proves that both extraction methods were able to produce high quality turmeric extract. (author)

Occurrence and distribution of pesticides in surface waters of the Hood River basin, Oregon, 1999-2009

Science.gov (United States)

Temple, Whitney B.; Johnson, Henry M.

2011-01-01

The U.S. Geological Survey analyzed pesticide and trace-element concentration data from the Hood River basin collected by the Oregon Department of Environmental Quality (ODEQ) from 1999 through 2009 to determine the distribution and concentrations of pesticides in the basin's surface waters. Instream concentrations were compared to (1) national and State water-quality standards established to protect aquatic organisms and (2) concentrations that cause sublethal or lethal effects in order to assess their potential to adversely affect the health of salmonids and their prey organisms. Three salmonid species native to the basin are listed as "threatened" under the U.S. Endangered Species Act: bull trout, steelhead, and Chinook salmon. A subset of 16 sites was sampled every year by the ODEQ for pesticides, with sample collection targeted to months of peak pesticide use in orchards (March-June and September). Ten pesticides and four pesticide degradation products were analyzed from 1999 through 2008; 100 were analyzed in 2009. Nineteen pesticides were detected: 11 insecticides, 6 herbicides, and 2 fungicides. Two of four insecticide degradation products were detected. All five detected organophosphate insecticides and the one detected organochlorine insecticide were present at concentrations exceeding water-quality standards, sublethal effects thresholds, or acute toxicity values in one or more samples. The frequency of organophosphate detection in the basin decreased during the period of record; however, changes in sampling schedule and laboratory reporting limits hindered clear analysis of detection frequency trends. Detected herbicide and fungicide concentrations were less than water-quality standards, sublethal effects thresholds, or acute toxicity values. Simazine, the most frequently detected pesticide, was the only herbicide detected at concentrations within an order of magnitude (factor of 10) of concentrations that impact salmonid olfaction. Some detected

Plutonium and americium extraction studies with bifunctional organophosphorus extractants

International Nuclear Information System (INIS)

Navratil, J.D.

1985-01-01

Neutral bifunctional organophosphorus extractants, such as octylphenyl-N,N-diisobutylcarbamoylmethylphosphine oxide (CMPO) and dihexyl-N,N-diethylcarbamoylmethylphosphonate (CMP), are under study at the Rocky Flats Plant (RFP) to remove plutonium and americium from the 7M nitric acid waste. These compounds extract trivalent actinides from strong nitric acid, a property which distinguishes them from monofunctional organiphosphorus reagents. Furthermore, the reagents extract hydroytic plutonium (IV) polymer which is present in the acid waste stream. The compounds extract trivalent actinides with a 3:1 stoichiometry, whereas tetra- and hexavalent actinides extract with a stoichiometry of 2:1. Preliminary studies indicate that the extracted plutonium polymer complex contains one to two molecules of CMP per plutonium ion and the plutonium(IV) maintains a polymeric structure. Recent studies by Horwitz and co-workers conclude that the CMPO and CMP reagents behave as monodentate ligands. At RFP, three techniques are being tested for using CMP and CMPO to remove plutonium and americium from nitric acid waste streams. The different techniques are liquid-liquid extraction, extraction chromatography, and solid-supported liquid membranes. Recent tests of the last two techniques will be briefly described. In all the experiments, CMP was an 84% pure material from Bray Oil Co. and CMPO was 98% pure from M and T Chemicals

Rapid extraction of PCDD/Fs from soil and fly ash samples. Pressurized fluid extraction (PFE) and microwave-assisted extraction (MAE)

Energy Technology Data Exchange (ETDEWEB)

Sanz, P.; Fabrellas, B. [Centro de Investigaciones Energeticas Medioambientales y Tecnologicas (CIEMAT), Madrid (Spain)

2004-09-15

The main reference extraction method in the analysis of polychlorinated dibenzop- dioxins and dibenzofurans (PCDD/Fs) is still the Soxhlet extraction. But it requires long extraction times (up to 24 hs), large volumes of hazardous organic solvents (100-300 ml) and its automation is limited. Pressurized Fluid Extraction (PFE) and Microwave-Assisted Extraction (MAE) are two relatively new extraction techniques that reduce the time and the volume of solvent required for extraction. However, very different PFE extraction conditions are found for the same enviromental matrices in the literature. MAE is not a extraction technique very applied for the analysis of PCDD/Fs yet, although it is used for the determination of other organic compounds, such as PCBs and PAHs. In this study, PFE and MAE extraction conditions were optimized to determine PCDDs y PCDFs in fly ash and soil/sediment samples. Conventional Soxhlet extraction with toluene was used to compare the extraction efficiency of both techniques.

ATLAS TileCal Sub-Module Production at UIUC - Production Submodule Photos (current)

CERN Multimedia

Errede, Steve

2000-01-01

Step 1 - Washing Plates Photo 1 - Spacers in their original box straight from the Czech Republic.. notice the large amounts of grease. Photo 2 - Spacers on the table ready to be washed. Photo 3 - Photo 3 - Scrubbing the grease off with Alconox

40 CFR 257.2 - Definitions.

Science.gov (United States)

2010-07-01

... grease removed from a grease trap at a restaurant. Facility means all contiguous land and structures... manure spreading operations) for agricultural purposes or for treatment and disposal. Landfill means an... industrial, commercial, mining, and agricultural operations, and from community activities, but does not...

Extraction efficiency of hydrophilic and lipophilic antioxidants from lyophilized foods using pressurized liquid extraction and manual extraction.

Science.gov (United States)

Watanabe, Jun; Oki, Tomoyuki; Takebayashi, Jun; Takano-Ishikawa, Yuko

2014-09-01

The efficient extraction of antioxidants from food samples is necessary in order to accurately measure their antioxidant capacities. α-Tocopherol and gallic acid were spiked into samples of 5 lyophilized and pulverized vegetables and fruits (onion, cabbage, Satsuma mandarin orange, pumpkin, and spinach). The lipophilic and hydrophilic antioxidants in the samples were sequentially extracted with a mixed solvent of n-hexane and dichloromethane, and then with acetic acid-acidified aqueous methanol. Duplicate samples were extracted: one set was extracted using an automated pressurized liquid extraction apparatus, and the other set was extracted manually. Spiked α-tocopherol and gallic acid were recovered almost quantitatively in the extracted lipophilic and hydrophilic fractions, respectively, especially when pressurized liquid extraction was used. The expected increase in lipophilic oxygen radical absorbance capacity (L-ORAC) due to spiking with α-tocopherol, and the expected increase in 2,2-diphenyl-1-picrylhydrazyl radical scavenging activities and total polyphenol content due to spiking with gallic acid, were all recovered in high yield. Relatively low recoveries, as reflected in the hydrophilic ORAC (H-ORAC) value, were obtained following spiking with gallic acid, suggesting an interaction between gallic acid and endogenous antioxidants. The H-ORAC values of gallic acid-spiked samples were almost the same as those of postadded (spiked) samples. These results clearly indicate that lipophilic and hydrophilic antioxidants are effectively extracted from lyophilized food, especially when pressurized liquid extraction is used. © 2014 Institute of Food Technologists®

The reduction of oil pollutants of petroleum products storage-tanks sludge using low-cost adsorbents

Directory of Open Access Journals (Sweden)

Mokhtari-Hosseini Zahra Beagom

2017-01-01

Full Text Available Disposal of storage tank sludge in oil depots is a major environmental concern due to the high concentration of hydrocarbons involved. This paper investigates the reduction of the sludge oil pollutants with initial oil and grease concentration of about 50 mass% using low cost adsorbents. Among the examined adsorbents, sawdust indicated the maximum removal of oil and grease. The screening and optimizing of process parameters were evaluated employing Plackett-Burman design and response surface method. For the optimized conditions, more than 60 mass% of oil and grease from the sludge was removed. Moreover, it was found that sawdust adsorption of the oil and grease approximately followed the Freundlich isotherm. The results indicated that oil pollutants of sludge could be reduced using sawdust as a low-cost, available and flammable adsorbent so that thus saturated adsorbents could be used as fuel in certain industries.

Determination of hydrogen in milligram quantities of titanium and its alloys

Science.gov (United States)

Otterson, D. A.; Smith, R. J.

1973-01-01

An accurate, versatile, and sensitive method for the determination of hydrogen in milligram-size titanium samples is presented. It involves extraction of hydrogen at 1070 K while a mercury diffusion pump transfers the evolved gases into the inlet of a mass spectrometer. All the evolved gases may then be positively identified and determined. This method can be readily adapted for use with other metals and for the study of the slow evolution of hydrogen. Reduction of interferences due to the evolution of hydrogen by reactions involving vapors such as those of water, acetone, and vacuum grease is discussed.

77 FR 462 - Regulation of Fuels and Fuel Additives: Identification of Additional Qualifying Renewable Fuel...

Science.gov (United States)

2012-01-05

... sources--qualifying as cellulosic biofuel: [cir] Thermochemical pyrolysis. [cir] Thermochemical... covercrops, algal oil, biogenic waste oils/fats/greases, non-food grade corn oil, Canola/rapeseed oil, and... from annual covercrops, algal oil, biogenic waste oils/fats/greases, or non- food grade corn oil using...

Novel Fluorinated Tensioactive Extractant Combined with Flotation for Decontamination of Extractant Residual during Solvent Extraction

Science.gov (United States)

Wu, Xue; Chang, Zhidong; Liu, Yao; Choe, Chol Ryong

2017-12-01

Solvent-extraction is widely used in chemical industry. Due to the amphiphilic character, a large amount of extractant remains in water phase, which causes not only loss of reagent, but also secondary contamination in water phase. Novel fluorinated extractants with ultra-low solubility in water were regarded as effective choice to reduce extractant loss in aqueous phase. However, trace amount of extractant still remained in water. Based on the high tensioactive aptitude of fluorinated solvent, flotation was applied to separate fluorinated extractant remaining in raffinate. According to the data of surface tension measurement, the surface tension of solution was obviously decreased with the addition of fluorinated extractant tris(2,2,3,3,4,4,5,5-octafluoropentyl) phosphate (FTAP). After flotation, the FTAP dissolved in water can be removed as much as 70%, which proved the feasibility of this key idea. The effects of operation time, gas velocity, pH and salinity of bulk solution on flotation performance were discussed. The optimum operating parameters were determined as gas velocity of 12ml/min, operating time of 15min, pH of 8.7, and NaCl volume concentration of 1.5%, respectively. Moreover, adsorption process of FTAP on bubble surface was simulated by ANSYS VOF model using SIMPLE algorithm. The dynamic mechanism of flotation was also theoretically investigated, which can be considered as supplement to the experimental results.

Development of a new separator oil/water: adaptation of a laboratory prototype envisage an industrial application; Desenvolvimento de um novo separador oleo/agua: adaptacao do prototipo de laboratorio visando aplicacao industrial

Energy Technology Data Exchange (ETDEWEB)

Medeiros, Gustavo de S.; Paulo, Joao B. de A.; Costa Junior, Jose A. [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil); Fernandes Junior, Wilaci E. [PETROBRAS, Natal/Fortaleza, RN/CE (Brazil). Unidade RN/CE

2008-07-01

The present work deals with the adaptation of a new separator oil/water called Mixer Settler based on Phase Inversion of (MDIF) in scale of laboratory for future application in industrial scale. The adaptations were carried out by changing of the materials of construction and the substitution of the original system of mechanical mixing by a static or on-line mixer. The equipment works through the unit operation of liquid-liquid extraction associated with the innovative method of phase inversion to separate the fine oil droplets which appear emulsified into produced waters. The extractant solvent was QAV (aviation kerosene). A composed central design was used to evaluate the performance of the equipment, considering the separation efficiency (%) as the response variable in function of the TOG (total oil and greases). Envisaging an industrial application we plotted contour curves to determine the regions which it is possible to operate the equipment on optimized conditions in view of separate oil at low concentrations, minimizing the quantity of extractant solvent. (author)

Binary solvent extraction system and extraction time effects on phenolic antioxidants from kenaf seeds (Hibiscus cannabinus L.) extracted by a pulsed ultrasonic-assisted extraction.

Science.gov (United States)

Wong, Yu Hua; Lau, Hwee Wen; Tan, Chin Ping; Long, Kamariah; Nyam, Kar Lin

2014-01-01

The aim of this study was to determine the best parameter for extracting phenolic-enriched kenaf (Hibiscus cannabinus L.) seeds by a pulsed ultrasonic-assisted extraction. The antioxidant activities of ultrasonic-assisted kenaf seed extracts (KSE) were determined by a 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging capacity assay, 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) radical scavenging assay, β -carotene bleaching inhibition assay, and ferric reducing antioxidant power (FRAP) assay. Total phenolic content (TPC) and total flavonoid content (TFC) evaluations were carried out to determine the phenolic and flavonoid contents in KSE. The KSE from the best extraction parameter was then subjected to high performance liquid chromatography (HPLC) to quantify the phenolic compounds. The optimised extraction condition employed 80% ethanol for 15 min, with the highest values determined for the DPPH, ABTS, and FRAP assay. KSE contained mainly tannic acid (2302.20 mg/100 g extract) and sinapic acid (1198.22 mg/100 g extract), which can be used as alternative antioxidants in the food industry.

Binary Solvent Extraction System and Extraction Time Effects on Phenolic Antioxidants from Kenaf Seeds (Hibiscus cannabinus L.) Extracted by a Pulsed Ultrasonic-Assisted Extraction

Science.gov (United States)

Lau, Hwee Wen; Nyam, Kar Lin

2014-01-01

The aim of this study was to determine the best parameter for extracting phenolic-enriched kenaf (Hibiscus cannabinus L.) seeds by a pulsed ultrasonic-assisted extraction. The antioxidant activities of ultrasonic-assisted kenaf seed extracts (KSE) were determined by a 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging capacity assay, 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) radical scavenging assay, β-carotene bleaching inhibition assay, and ferric reducing antioxidant power (FRAP) assay. Total phenolic content (TPC) and total flavonoid content (TFC) evaluations were carried out to determine the phenolic and flavonoid contents in KSE. The KSE from the best extraction parameter was then subjected to high performance liquid chromatography (HPLC) to quantify the phenolic compounds. The optimised extraction condition employed 80% ethanol for 15 min, with the highest values determined for the DPPH, ABTS, and FRAP assay. KSE contained mainly tannic acid (2302.20 mg/100 g extract) and sinapic acid (1198.22 mg/100 g extract), which can be used as alternative antioxidants in the food industry. PMID:24592184

Binary Solvent Extraction System and Extraction Time Effects on Phenolic Antioxidants from Kenaf Seeds (Hibiscus cannabinus L. Extracted by a Pulsed Ultrasonic-Assisted Extraction

Directory of Open Access Journals (Sweden)

Yu Hua Wong

2014-01-01

Full Text Available The aim of this study was to determine the best parameter for extracting phenolic-enriched kenaf (Hibiscus cannabinus L. seeds by a pulsed ultrasonic-assisted extraction. The antioxidant activities of ultrasonic-assisted kenaf seed extracts (KSE were determined by a 2,2-diphenyl-1-picrylhydrazyl (DPPH radical scavenging capacity assay, 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid (ABTS radical scavenging assay, β-carotene bleaching inhibition assay, and ferric reducing antioxidant power (FRAP assay. Total phenolic content (TPC and total flavonoid content (TFC evaluations were carried out to determine the phenolic and flavonoid contents in KSE. The KSE from the best extraction parameter was then subjected to high performance liquid chromatography (HPLC to quantify the phenolic compounds. The optimised extraction condition employed 80% ethanol for 15 min, with the highest values determined for the DPPH, ABTS, and FRAP assay. KSE contained mainly tannic acid (2302.20 mg/100 g extract and sinapic acid (1198.22 mg/100 g extract, which can be used as alternative antioxidants in the food industry.

Just Greasing the Wheels?

DEFF Research Database (Denmark)

Adler-Nissen, Rebecca

2015-01-01

We traditionally see diplomats as mediators.They build bridges between nations and they repair them when they break. During a crisis, diplomats ‘keep it cool’ and try to prevent the crisis from worsening into armed conflict. Diplomats are the men and women who keep the international system runnin...

Unsymmetrical phosphate as extractant for the extraction of nitric acid

International Nuclear Information System (INIS)

Gaikwad, R.H.; Jayaram, R.V.

2016-01-01

Tri-n-butyl phosphate (TBP) was first used as an extractant in 1944, during Manhattan project for the separation of actinides and further explored by Warf in 1949 for the extraction of Ce(IV) from aqueous nitric acid. TBP was further used as an extractant in the Plutonium Uranium Recovery by Extraction (PUREX) process. To meet the stringent requirements of the nuclear industry TBP has been extensively investigated. In spite of its wide applicability, TBP suffers from various disadvantages such as high aqueous solubility, third phase formation, chemical and radiation degradation leading to the formation of undesired products. It also suffers from incomplete decontamination of the actinides from fission products. Various attempts have been made to overcome the problems associated with TBP by way of using higher homologues of TBP such as Tri-iso amyl phosphate (TiAP), Tri-secondary butyl phosphate (TsBP), Tri amyl phosphate (TAP). It was found that in some cases the results were considerably better than those obtained with TBP for uranium/thorium extraction. The extraction of nitric acid by TBP and its higher homologues which are symmetrical are well documented. However, no solvent has emerged clearly superior than TBP. Here in we report the extraction of nitric acid with neutral unsymmetrical phosphates and study them as extractants for the extraction of nitric acid. Dibutyl secbutyl phosphate, dibutyl pentyl phosphate and dibutyl heptyl phosphate were synthesised for this purpose and the extraction of nitric acid was studied in n-dodecane. The results indicate that the substitution of one of the alkyl groups of the symmetrical phosphate adjacent to the phosphoryl (P=O) group of the phosphate does not have any pronounced effect on the extraction capacity of nitric acid. (author)

A comparison of accelerated solvent extraction, Soxhlet extraction, and ultrasonic-assisted extraction for analysis of terpenoids and sterols in tobacco.

Science.gov (United States)

Shen, Jinchao; Shao, Xueguang

2005-11-01

The performance of accelerated solvent extraction in the analysis of terpenoids and sterols in tobacco samples was investigated and compared with those of Soxhlet extraction and ultrasonically assisted extraction with respect to yield, extraction time, reproducibility and solvent consumption. The results indicate that although the highest yield was achieved by Soxhlet extraction, ASE appears to be a promising alternative to classical methods since it is faster and uses less solvent, especially when applied to the investigation of large batch tobacco samples. However, Soxhlet extraction is still the preferred method for analyzing sterols since it gives a higher extraction efficiency than other methods.

Tiny Bird, Huge Mystery-The Possibly Extinct Hooded Seedeater (Sporophila melanops Is a Capuchino with a Melanistic Cap.

Directory of Open Access Journals (Sweden)

Juan Ignacio Areta

Full Text Available Known with certainty solely from a unique male specimen collected in central Brazil in the first quarter of the 19th century, the Critically Endangered (Possibly Extinct Hooded Seedeater Sporophila melanops has been one of the great enigmas of Neotropical ornithology, arguably the only one of a host of long-lost species from Brazil to remain obstinately undiscovered. We reanalysed the morphology of the type specimen, as well as a female specimen postulated to represent the same taxon, and sequenced mitochondrial DNA (COI and Cyt-b from both individuals. Furthermore, we visited the type locality, at the border between Goiás and Mato Grosso, and its environs on multiple occasions at different seasons, searching for birds with similar morphology to the type, without success. Novel genetic and morphological evidence clearly demonstrates that the type of S. melanops is not closely related to Yellow-bellied Seedeater S. nigricollis, as has been frequently postulated in the literature, but is in fact a representative of one of the so-called capuchinos, a clade of attractively plumaged seedeaters that breed mostly in the Southern Cone of South America. Our morphological analysis indicates that S. melanops has a hitherto unreported dark-coffee throat and that it is probably a Dark-throated Seedeater S. ruficollis collected within its wintering range, acquiring breeding plumage and showing melanism on the cap feathers. Alternatively, it may be a melanistic-capped individual of a local population of seedeaters known to breed in the Esteros del Iberá, Corrientes, Argentina, to which the name S. ruficollis might be applicable, whilst the name S. plumbeiceps might be available for what is currently known as S. ruficollis. A hybrid origin for S. melanops cannot be ruled out from the available data, but seems unlikely. The purported female specimen of S. melanops pertains either to S. nigricollis or to Double-collared Seedeater S. caerulescens based on

Understanding extractive bleed : wood extractives: distribution, properties, and classes

Science.gov (United States)

Edward Burke; Norm Slavik; Tony Bonura; Dennis Connelly; Tom Faris; Arnie Nebelsick; Brent Stuart; Sam Williams; Alex C. Wiedenhoeft

2010-01-01

Color, odor, and natural durability of heartwood are characteristics imparted by a class of chemicals in wood known collectively extractives. Wood is converted by the tree from sapwood to heartwood by the deposition of extractives, typically many years after the growth ring undergoing this change was formed by the tree. Extractives are thus not a part of the wood...

Supercritical CO2 extraction of raw propolis and its dry ethanolic extract

Directory of Open Access Journals (Sweden)

L. C. Paviani

2012-06-01

Full Text Available Three types of propolis extract were prepared and analyzed with respect to their global extraction yields and with respect to the concentration of the following markers: 3,5-diprenyl-4-hydroxycinnamic acid; 3-prenyl-4-hydroxycinnamic acid; 4-hydroxycinnamic acid and 4-methoxy-3,5,7-trihydroxyflavone. The extract EEP (ethanolic extract of propolis was obtained by the conventional method from raw propolis using ethanol as solvent. The extracts (SFE were obtained by supercritical solvent extraction from the raw propolis using supercritical carbon dioxide (sc-CO2, with and without the addition of ethanol as a co-solvent. The fractionated supercritical extracts (FSCE were obtained by fractionation (extract and raffinate of the dry EEP with sc-CO2. EEP yields of 39.5% were obtained and maximum global extraction yields were 7.3% for SFE with no co-solvent, 51% for SFE with 15% ethanol and 18% for the FSCE extract fraction. The concentrations of the markers in the different extracts differed as a function of the operational parameters, indicating that the addition of co-solvent and the selectivity of sc-CO2 could be manipulated so as to obtain extracts with the yields and concentrations of interest.

Characterization of gizzards and grits of wild cranes found dead at Izumi Plain in Japan.

Science.gov (United States)

Uegomori, Mima; Haraguchi, Yuko; Obi, Takeshi; Takase, Kozo

2018-04-18

We analyzed the gizzards, and grits retained in the gizzards of 41 cranes that migrated to the Izumi Plain during the winter of 2015/2016 and died there, either due to accident or disease. These included 31 Hooded Cranes (Grus monacha) and 10 White-naped Cranes (G. vipio). We determined body weight, gizzard weight, total grit weight and number per gizzard, and size, shape, and surface roundness of the grits. Average gizzard weights were 92.4 g for Hooded Cranes and 97.1 g for White-naped Cranes, and gizzard weight positively correlated with body weight in both species. Average total grit weights per gizzard were 19.7 g in Hooded Cranes and 25.7 g in White-naped Cranes, and were significantly higher in the latter. Average percentages of body weight to grit weight were 0.8% in Hooded Cranes and 0.5% in White-naped Cranes. Average grit number per gizzard was 693.5 in Hooded Cranes and 924.2 in White-naped Cranes, and were significantly higher in the latter. The average grit size was 2.8 mm in both species. No differences were found in the shape and surface roundness of grits between the two species. To the best of our knowledge, this is the first study on the grits retained in the gizzards of Hooded and White-naped Cranes.

Organization of extracting molecules of the diamide type: link with the extracting properties?

International Nuclear Information System (INIS)

Meridiano, Y.

2009-02-01

The aim of these studies is to establish a link between the different organizations of diamide extractants (used in the DIAMEX process) and their extracting properties. The effects of the key parameters leading the liquid-liquid extraction (concentration of extractant, nature of solute, activity of the aqueous phase, nature of the diluent and temperature) are studied: 1) at the supramolecular scale, with the characterization of the extractant organizations by vapor-pressure osmometry (VPO) and small angle neutron and X-ray scattering (SANS/SAXS) experiments; 2) at the molecular scale, with the quantification of the extracted solutes (water, nitric acid, metal nitrate) and the determination of extracted complexes stoichiometries by electro-spray mass spectrometry (ESI-MS) experiments. The DMDOHEMA molecule acts as a classical surfactant and forms aggregates of the reverse micelle type. Taking into account the established supramolecular diagrams, a quantitative link between the extractants structures and their extracting properties has been brought to light. To model the europium nitrate extraction, two approaches have been developed: - an approach based on mass action laws. Extractions equilibria have been proposed taking into account the supramolecular speciation; - an innovative approach considering the extracted ions as adsorbed on a specific surface of the extractant molecule which depends on the extractant organization state. The ion extraction can be considered as a sum of isotherms corresponding to the different states of organization. This approach allows to compare the extraction efficiency of an extracting molecule as a function of its organization state. (author)

EXTRACTION OF MONOAZO DYES BY HYDROPHILIC EXTRACTANTS FROM AQUEOUS SOLUTIONS

Directory of Open Access Journals (Sweden)

Y. I. Korenman

2012-01-01

Full Text Available The extraction of mono azo dyes E102, E122, E110, E124, E129 from aqueous solutions with hydrophilic solvents (alcohols, esters, ketones and polymers (poly-N-vinylamides, polyethylene glycol was studied. The main regularities of extraction are established. The distribution coefficients and degree of extraction of dyes was estimate. The influence of the nature of solvents and polymers on the extraction of dyes from aqueous solutions are established.

Antioxidant activities of extracts from five edible mushrooms using different extractants

Directory of Open Access Journals (Sweden)

Suphaphit Boonsong

2016-03-01

Full Text Available Extractions were performed of the total phenolic and flavonoid contents and antioxidant properties of five edible mushroom samples—Lentinus edodes, Volvariella volvacea, Pleurotus eous, Pleurotus sajor-caju and Auricularia auricular—using three different extractants. Among the three different extractants, 50% (volume per volume; v/v ethanol was the most suitable for antioxidant extraction from the mushroom samples. The 50% (v/v ethanolic extract of dried L. edodes contained higher total phenolic and flavonoid contents than in the other mushroom extract samples. The antioxidant activities of 50% (v/v ethanolic extract of dried L. edodes showed the strongest 2,2-diphenyl-1-picrylhydrazyl radical-scavenging assay (64.34% compared to butylated hydroxyanisole (BHA and α-tocopherol at 500 μg/mL. The ethanolic extract showed a lower reducing power of 0.10 compared to BHA and α-tocopherol at 500 μg/mL. Moreover, the L. edodes ethanolic extract also had the highest chelating ability (66.28% which was lower than for ethylenediaminetetraacetic acid at 500 μg/mL and showed the strongest superoxide radical-scavenging activity (64.17% compared to BHA and α-tocopherol. Therefore, the 50% (v/v ethanolic extract of L. edodes could be used as a potential natural antioxidative source or as an ingredient in the fish and fishery product industries.

Influence of Extraction Parameters on Hydroalcohol Extracts of the ...

African Journals Online (AJOL)

... the influence of alcohol concentration (50, 70 and 90 % v/v), extraction time (2, 6 and 10 h), and particle size of the herbal drug (0.25, 0.5 and 1.0 mm) on the pH, dry residue and myrsinoic acid B (MAB) content of hydroalcoholic extracts by high performance liquid chromatography (HPLC) method. Results: For the extracts, ...

Biopretreatment of palm oil mill effluent by thermotolerant polymer-producing fungi

Directory of Open Access Journals (Sweden)

Masao Ukita

2001-11-01

Full Text Available Palm oil industry is one of the three major agro-industries in Southern Thailand and generates large quantities of effluent with high organic matter (BOD and COD values of 58,000 and 110,000 mg/l, respectively, total solids and suspended solids (70,000 and 40,000 mg/l, respectively, oil & grease (25,600 mg/l, and has a low pH (4.5. Conventional anaerobic ponding system is normally employed in palm oil mills to treat the effluent. To increase its efficiency, biopretreatment to remove the organic matter and oil & grease by thermotolerant polymer-producing fungi was investigated. The palm oil mill effluent (POME was treated by the two thermotolerant polymer-producing fungi, Rhizopus sp. ST4 and Rhizopus sp. ST29, at 45ºC under aseptic and septic conditions. Rhizopus sp. ST4 gave the same oil & grease removal (84.2% under both conditions but COD removal under septic condition (62.2% was 8.8% higher than that under aseptic condition (53.4%. On the contrary, Rhizopus sp. ST 29 under aseptic condition showed 11% and 25.4% higher oil & grease removal (91.4% and COD removal (66.0% than those under septic condition. Comparison between the two isolates under aseptic condition revealed that Rhizopus sp. ST29 exhibited higher oil & grease removal (91.4% as well as COD removal (66.0% than those of Rhizopus sp. ST4 (84.2% and 53.4%, respectively. Under septic condition, Rhizopus sp. ST4 gave higher oil & grease removal (84.2% and COD removal (62.2% than did Rhizopus sp. ST 29 (80.5 and 40.6%, respectively.

EXTRACT

DEFF Research Database (Denmark)

Pafilis, Evangelos; Buttigieg, Pier Luigi; Ferrell, Barbra

2016-01-01

The microbial and molecular ecology research communities have made substantial progress on developing standards for annotating samples with environment metadata. However, sample manual annotation is a highly labor intensive process and requires familiarity with the terminologies used. We have the...... and text-mining-assisted curation revealed that EXTRACT speeds up annotation by 15-25% and helps curators to detect terms that would otherwise have been missed.Database URL: https://extract.hcmr.gr/......., organism, tissue and disease terms. The evaluators in the BioCreative V Interactive Annotation Task found the system to be intuitive, useful, well documented and sufficiently accurate to be helpful in spotting relevant text passages and extracting organism and environment terms. Comparison of fully manual...

Bioremediation of hydrocarbon-contaminated soils: are treatability and ecotoxicity endpoints related?

International Nuclear Information System (INIS)

Visser, S.

1999-01-01

To determine if there is a relationship between biotreatability and ecotoxicity endpoints in a wide range of hydrocarbon-contaminated soils, including medium and heavy crude oil-contaminated flare pit wastes and lubrication oil contaminated soil, research was conducted. Each test material was analyzed for pH, water repellency, electrical conductivity, available N and P, total extractable hydrocarbons, oil and grease, and toxicity to seedling emergence, root elongation in barley, lettuce and canola, earthworm survival and luminescent bacteria (Microtox), prior to, and following three months of bioremediation in the laboratory. By monitoring soil respiration, progress of the bioremediation process and determination of a treatment endpoint were assessed. The time required to attain a treatment endpoint under laboratory conditions can range from 30 days to 100 days depending on the concentration of hydrocarbons and degree of weathering. Most flare pits are biotreatable, averaging a loss of 25-30% of hydrocarbons during bioremediation. Once a treatment endpoint is achieved, residual hydrocarbons contents almost always exceeds Alberta Tier I criteria for mineral oil and grease. As a result of bioremediation treatments, hydrophobicity is often reduced from severe to low. Many flare pit materials are still moderately to extremely toxic after reaching a treatment endpoint. (Abstract only)

Investigation of Thermal Interface Materials Using Phase-Sensitive Transient Thermoreflectance Technique: Preprint

Energy Technology Data Exchange (ETDEWEB)

Feng, X.; King, C.; DeVoto, D.; Mihalic, M.; Narumanchi, S.

2014-08-01

With increasing power density in electronics packages/modules, thermal resistances at multiple interfaces are a bottleneck to efficient heat removal from the package. In this work, the performance of thermal interface materials such as grease, thermoplastic adhesives and diffusion-bonded interfaces are characterized using the phase-sensitive transient thermoreflectance technique. A multi-layer heat conduction model was constructed and theoretical solutions were derived to obtain the relation between phase lag and the thermal/physical properties. This technique enables simultaneous extraction of the contact resistance and bulk thermal conductivity of the TIMs. With the measurements, the bulk thermal conductivity of Dow TC-5022 thermal grease (70 to 75 um bondline thickness) was 3 to 5 W/(m-K) and the contact resistance was 5 to 10 mm2-K/W. For the Btech thermoplastic material (45 to 80 μm bondline thickness), the bulk thermal conductivity was 20 to 50 W/(m-K) and the contact resistance was 2 to 5 mm2-K/W. Measurements were also conducted to quantify the thermal performance of diffusion-bonded interface for power electronics applications. Results with the diffusion-bonded sample showed that the interfacial thermal resistance is more than one order of magnitude lower than those of traditional TIMs, suggesting potential pathways to efficient thermal management.

Effect of soybean extract after tooth extraction on osteoblast numbers

Directory of Open Access Journals (Sweden)

Rosa Sharon Suhono

2011-06-01

Full Text Available Background: Many researches were done to find natural materials that may increase and promote bone healing processes after trauma and surgery. One of natural material that had been studied was soybean extract which contains phytoestrogen, a non-steroidal compounds found in plants that may binds to estrogen receptors and have estrogen-like activity. Purpose: The aim of this study was to investigate the effect of soybean extract feeding on the number of osteoblast cells in alveolar bone socket after mandibular tooth extraction. Methods: This study was studied on male Rattus norvegicus strain Wistar. Seventeen rats divided into three groups were used in this study. Group 1 fed with carboxy methyl cellulose (CMC solution 0,2% for seven days, and the left mandibular central incisivus was extracted; group 2 fed with soybean extract for seven days and the left mandibular central incisives was extracted; group 3 received the left mandibular central incisives extraction followed by soybean extract feeding for seven days after the extraction. All groups were sacrificed on the seventh day post-extraction, and the alveolar bone sockets were taken for histopathological observation. The tissues were processed and stained using hematoxylin and eosin to identify the amount of osteoblast cells. The number of osteoblast cells was counted using an Image Tool program. The data was analyzed statistically using the One-Way ANOVA test. Results: Significant differences were found on the number of osteoblast cells in alveolar bone after tooth extraction between groups. Group 2 (fed with soybean extract is higher than group 1 (fed with CMC and group 3 (fed with soybean extract after extraction. Conclusion: Soybean extract feeding that given for seven days pre-tooth extraction can increase the number of osteoblast cells compared with the group that were not given soybean extract feeding and also with the group that were given soybean extract feeding for seven days post

Bevalac extraction

International Nuclear Information System (INIS)

Kalnins, J.G.; Krebs, G.; Tekawa, M.; Cowles, D.; Byrne, T.

1992-02-01

This report will describe some of the general features of the Bevatron extraction system, primarily the dependence of the beam parameters and extraction magnet currents on the Bevalac field. The extraction magnets considered are: PFW, XPl, XP2, XS1, XS2, XM1, XM2, XM3, XQ3A and X03B. This study is based on 84 past tunes (from 1987 to the present) of various ions (p,He,O,Ne,Si,S,Ar,Ca,Ti,Fe,Nb,La,Au and U), for Bevalac fields from 1.749 to 12.575 kG, where all tunes included a complete set of beam line wire chamber pictures. The circulating beam intensity inside the Bevalac is measured with Beam Induction Electrodes (BIE) in the South Tangent Tank. The extracted beam intensity is usually measured with the Secondary Emission Monitor (SEM) in the F1-Box. For most of the tunes the extraction efficiency, as given by the SEM/BIE ratio, was not recorded in the MCR Log Book, but plotting the available Log Book data as a function of the Bevalac field, see Fig.9, we find that the extraction efficiency is typically between 30->60% with feedback spill

Extracting natural dyes from wool--an evaluation of extraction methods.

Science.gov (United States)

Manhita, Ana; Ferreira, Teresa; Candeias, António; Dias, Cristina Barrocas

2011-05-01

The efficiency of eight different procedures used for the extraction of natural dyes was evaluated using contemporary wool samples dyed with cochineal, madder, woad, weld, brazilwood and logwood. Comparison was made based on the LC-DAD peak areas of the natural dye's main components which had been extracted from the wool samples. Among the tested methods, an extraction procedure with Na(2)EDTA in water/DMF (1:1, v/v) proved to be the most suitable for the extraction of the studied dyes, which presented a wide range of chemical structures. The identification of the natural dyes used in the making of an eighteenth century Arraiolos carpet was possible using the Na(2)EDTA/DMF extraction of the wool embroidery samples and an LC-DAD-MS methodology. The effectiveness of the Na(2)EDTA/DMF extraction method was particularly observed in the extraction of weld dye components. Nine flavone derivatives previously identified in weld extracts could be identified in a single historical sample, confirming the use of this natural dye in the making of Arraiolos carpets. Indigo and brazilwood were also identified in the samples, and despite the fact that these natural dyes were referred in the historical recipes of Arraiolos dyeing, it is the first time that the use of brazilwood is confirmed. Mordant analysis by ICP-MS identified the widespread use of alum in the dyeing process, but in some samples with darker hues, high amounts of iron were found instead.

Comparative analysis of essential oil composition of Iranian and Indian Nigella sativa L. extracted using supercritical fluid extraction and solvent extraction.

Science.gov (United States)

Ghahramanloo, Kourosh Hasanzadeh; Kamalidehghan, Behnam; Akbari Javar, Hamid; Teguh Widodo, Riyanto; Majidzadeh, Keivan; Noordin, Mohamed Ibrahim

2017-01-01

The objective of this study was to compare the oil extraction yield and essential oil composition of Indian and Iranian Nigella sativa L. extracted by using Supercritical Fluid Extraction (SFE) and solvent extraction methods. In this study, a gas chromatography equipped with a mass spectrophotometer detector was employed for qualitative analysis of the essential oil composition of Indian and Iranian N. sativa L. The results indicated that the main fatty acid composition identified in the essential oils extracted by using SFE and solvent extraction were linoleic acid (22.4%-61.85%) and oleic acid (1.64%-18.97%). Thymoquinone (0.72%-21.03%) was found to be the major volatile compound in the extracted N. sativa oil. It was observed that the oil extraction efficiency obtained from SFE was significantly ( P essential oil, which is composed of higher linoleic acid and thymoquinone contents compared to the essential oil obtained by the solvent extraction technique.

Reducing Contact Resistance Errors In Measuring Thermal ...

African Journals Online (AJOL)

Values of thermal conductivity (k) of glass beads, quartz sand, stone dust and clay were determined using a thermal probe with and without heat sink compounds (arctic silver grease (ASG) and white grease (WG)) at different water contents, bulk densities and particle sizes. The heat sink compounds (HSC) increased k at ...

Recyclable zein-coated kraft paper and linerboard

Science.gov (United States)

Nicholas Parris; Marguerite Sykes; Leland C. Dickey; Jack L. Wiles; Thomas J. Urbanik; Peter H. Cooke

2002-01-01

Recyclability of kraft paper and linerboard coated with commercial zein and paraffin wax or a zein-lipid mixture was evaluated using conventional recycling processes. Zein, an alcohol-soluble protein from corn, exhibits both grease and water vapor barrier properties. Strength properties, grease resistance, and water vapor barrier proper-ties were measured on handsheets...

Comparative analysis of essential oil composition of Iranian and Indian Nigella sativa L. extracted using supercritical fluid extraction and solvent extraction

Directory of Open Access Journals (Sweden)

Ghahramanloo KH

2017-07-01

Full Text Available Kourosh Hasanzadeh Ghahramanloo,1 Behnam Kamalidehghan,2 Hamid Akbari Javar,3 Riyanto Teguh Widodo,1 Keivan Majidzadeh,4 Mohamed Ibrahim Noordin1 1Department of Pharmacy, Faculty of Medicine, University of Malaya, Kuala Lumpur, Malaysia; 2Medical Genetics Department, National Institute of Genetic Engineering and Biotechnology (NIGEB, 3Department of Pharmaceutics, Faculty of Pharmacy, Tehran University of Medical Sciences (TUMS, 4Breast Cancer Research Center (BCRC Academic Center for Education, Culture and Research, Tehran, Iran Abstract: The objective of this study was to compare the oil extraction yield and essential oil composition of Indian and Iranian Nigella sativa L. extracted by using Supercritical Fluid Extraction (SFE and solvent extraction methods. In this study, a gas chromatography equipped with a mass spectrophotometer detector was employed for qualitative analysis of the essential oil composition of Indian and Iranian N. sativa L. The results indicated that the main fatty acid composition identified in the essential oils extracted by using SFE and solvent extraction were linoleic acid (22.4%–61.85% and oleic acid (1.64%–18.97%. Thymoquinone (0.72%–21.03% was found to be the major volatile compound in the extracted N. sativa oil. It was observed that the oil extraction efficiency obtained from SFE was significantly (P<0.05 higher than that achieved by the solvent extraction technique. The present study showed that SFE can be used as a more efficient technique for extraction of N. Sativa L. essential oil, which is composed of higher linoleic acid and thymoquinone contents compared to the essential oil obtained by the solvent extraction technique. Keywords: Nigella sativa L., essential oil extraction, supercritical fluid extraction, solvent extraction, fatty acid composition, thymoquinone, linoleic acid

Extraction of Tetravalent Uranium by Certain Acidic Organophosphorus Extractants from Phosphate Medium

International Nuclear Information System (INIS)

Daoud, J.A.; Zeid, M.M.; Aly, H.F.

1998-01-01

The extraction of U(IV) by octylphenyl acid phosphate (OPAP) or di-2-ethylhexyl phosphoric acid (HDEHP) in kerosene from phosphoric acid was carried out. The effect of extractant, phosphoric acid, uranium, Fe(II) and Fe(III) concentration on the extraction process was separately investigated. The effect of different reagents and temperature on the stripping of U(IV) was also investigated. The results obtained for the extraction of U(IV) by HDEHP showed that the extraction with the increase in HDEHP and Fe(III) concentration while it decreases with the increase in phosphoric acid, uranium and Fe(II) concentration. In case of extraction with OPAP, the extraction of U(IV) was found to decrease with the phosphoric acid, Fe(II) and initial uranium concentration while the increase in OPAP concentration slightly affected the extraction. The use of high phosphoric acid concentration as stripper at low temperature was found to give the best stripping results

Information extraction system

Science.gov (United States)

Lemmond, Tracy D; Hanley, William G; Guensche, Joseph Wendell; Perry, Nathan C; Nitao, John J; Kidwell, Paul Brandon; Boakye, Kofi Agyeman; Glaser, Ron E; Prenger, Ryan James

2014-05-13

An information extraction system and methods of operating the system are provided. In particular, an information extraction system for performing meta-extraction of named entities of people, organizations, and locations as well as relationships and events from text documents are described herein.

COMPARISONS OF SOXHLET EXTRACTION, PRESSURIZED LIQUID EXTRACTION, SUPERCRITICAL FLUID EXTRACTION, AND SUBCRITICAL WATER EXTRACTION FOR ENVIRONMENTAL SOLIDS: RECOVERY, SELECTIVITY, AND EFFECTS ON SAMPLE MATRIX. (R825394)

Science.gov (United States)

Extractions of a polycyclic aromatic hydrocarbon (PAH)-contaminated soil from a former manufactured gas plant site were performed with a Soxhlet apparatus (18 h), by pressurized liquid extraction (PLE) (50 min at 100°C), supercritical fluid extraction (SFE) (1 h at 150°...

Method of freezing type dismantling for wasted reactors

International Nuclear Information System (INIS)

Tatsumi, Toshiyuki.

1985-01-01

Purpose: To enable to operate a cutting device in the air by placing a working table on ice while utilizing the ice as radiation shielding materials thereby prevent the diffusion of air contaminations. Method: Upon dismantling a BWR type reactor, ice is packed into a reactor container and a pressure vessel and frozen state is maintained by cooling coils disposed to the outer circumference of the pressure vessel. Then, an airtight hood is covered over the pressure vessel and a working table is rotatably disposed therein. Upon working, when the upper layer ice is melted by a heat pump and discharged, the airtight hood is lowered to a predetermined level. After freezing the melted portion again at the lowered level, cutting work is conducted by an operator in the hood. The cut pieces are conveyed after hoisting the airtight hood by a crane. The pressure vessel is dismantled by repeating the foregoing procedures. In this way, cut pieces can be recovered without falling them to the reactor bottom as in the conventional work in water. In addition, since the procedures are conducted while covering the airtight hood, diffusion of air contaminations can be prevented. (Kamimura, M.)

ALARA review for the decontamination and decommissioning of the 233-S P.R. can loadout and decontamination

International Nuclear Information System (INIS)

Kornish, J.M.

1998-01-01

The 233-S Facility was completed in 1955 to expand plutonium production by further concentrating the plutonium nitrate product solution from the Reduction Oxidation (REDOX) Plant. The facility is radiologically contaminated because of operations and accidents. The building is presently a Hazard Category 2 Nuclear Facility. Disassembly of the loadout hood and its associated equipment may be done in parallel with the isolation of 233-S from REDOX via the pipe trench equipment removal. The work scope is to remove the entire loadout hood from the Product Receiver (P.R.) Can Loadout and Decon Room inside the 233-S Facility. A formal as low as reasonably achievable (ALARA) review is required by BHI-SH-02, Vol. 1, Procedure 1.22, Planning Radiological Work, when radiological conditions exceed trigger levels. The level of contamination inside the loadout hood and its associated equipment is unknown. The potential exists to exceed the level of loose surface contamination, which requires a formal ALARA review when opening the loadout hood and disassembly commences. This ALARA review is for the task instruction 1997-03-18-010 Revision 0, 233-S Loadout Hood Decon and Dismantlement

Extraction and determination of total flavonoids in jujube by alcohol extraction

Science.gov (United States)

Ji, Y. B.; Ru, X.; Yu, M.; Wang, S. W.; Lu, L.; Qiao, A. N.; Guo, A. Z.

2017-12-01

Jujube is a ripe fruit of Rhamnaceae. Its main active component is flavonoids, so the extraction and determination of total flavonoids in jujube will help to develop and utilize the medicinal value of jujube. In this study, the total flavonoids were extracted from jujube by alcohol extraction method. Through single factor investigation and orthogonal test, it was found that the total flavonoids content in jujube was the highest under the condition of 70°C, material ratio of 1:40, and extraction of 30 min by 70% ethanol. The content of total flavonoids in the extract of jujube was 1.57% at the wavelength of 510 nm by UV and rutin as the standard. The method was evaluated by methodological study, and it was determined that this method could be used as the detection of total flavonoids in jujube extraction.

Membrane extraction instead of solvent extraction - what does it give

International Nuclear Information System (INIS)

Macasek, F.

1989-01-01

Membrane extraction, i.e. separation in double-emulsion systems, is analyzed theoretically as a three-phase distribution process. Its efficiency is evaluated from the point of view of chemical equilibria and diffusion transport kinetics. The main advantages of membrane extraction as compared with solvent extraction are in higher yields (for preconcentration) and higher capacity for recovery of solutes. A pertraction factor and multiplication factor were defined. They are convenient parameters for numerical characterization of solute distribution, system capacity, process economics, and separation kinetics (both at a linear and non-linear extraction isotherm). 17 refs.; 4 figs

Extraction of bioactive carbohydrates from artichoke (Cynara scolymus L.) external bracts using microwave assisted extraction and pressurized liquid extraction.

Science.gov (United States)

Ruiz-Aceituno, Laura; García-Sarrió, M Jesús; Alonso-Rodriguez, Belén; Ramos, Lourdes; Sanz, M Luz

2016-04-01

Microwave assisted extraction (MAE) and pressurized liquid extraction (PLE) methods using water as solvent have been optimized by means of a Box-Behnken and 3(2) composite experimental designs, respectively, for the effective extraction of bioactive carbohydrates (inositols and inulin) from artichoke (Cynara scolymus L.) external bracts. MAE at 60 °C for 3 min of 0.3 g of sample allowed the extraction of slightly higher concentrations of inositol than PLE at 75 °C for 26.7 min (11.6 mg/g dry sample vs. 7.6 mg/g dry sample). On the contrary, under these conditions, higher concentrations of inulin were extracted with the latter technique (185.4 mg/g vs. 96.4 mg/g dry sample), considering two successive extraction cycles for both techniques. Both methodologies can be considered appropriate for the simultaneous extraction of these bioactive carbohydrates from this particular industrial by-product. To the best of our knowledge this is the first time that these techniques are applied for this purpose. Copyright © 2015 Elsevier Ltd. All rights reserved.

Comparative exergy analyses of Jatropha curcas oil extraction methods: Solvent and mechanical extraction processes

International Nuclear Information System (INIS)

Ofori-Boateng, Cynthia; Keat Teong, Lee; JitKang, Lim

2012-01-01

Highlights: ► Exergy analysis detects locations of resource degradation within a process. ► Solvent extraction is six times exergetically destructive than mechanical extraction. ► Mechanical extraction of jatropha oil is 95.93% exergetically efficient. ► Solvent extraction of jatropha oil is 79.35% exergetically efficient. ► Exergy analysis of oil extraction processes allow room for improvements. - Abstract: Vegetable oil extraction processes are found to be energy intensive. Thermodynamically, any energy intensive process is considered to degrade the most useful part of energy that is available to produce work. This study uses literature values to compare the efficiencies and degradation of the useful energy within Jatropha curcas oil during oil extraction taking into account solvent and mechanical extraction methods. According to this study, J. curcas seeds on processing into J. curcas oil is upgraded with mechanical extraction but degraded with solvent extraction processes. For mechanical extraction, the total internal exergy destroyed is 3006 MJ which is about six times less than that for solvent extraction (18,072 MJ) for 1 ton J. curcas oil produced. The pretreatment processes of the J. curcas seeds recorded a total internal exergy destructions of 5768 MJ accounting for 24% of the total internal exergy destroyed for solvent extraction processes and 66% for mechanical extraction. The exergetic efficiencies recorded are 79.35% and 95.93% for solvent and mechanical extraction processes of J. curcas oil respectively. Hence, mechanical oil extraction processes are exergetically efficient than solvent extraction processes. Possible improvement methods are also elaborated in this study.

Tryptophan depletion affects compulsive behaviour in rats

DEFF Research Database (Denmark)

Merchán, A; Navarro, S V; Klein, A B

2017-01-01

investigated whether 5-HT manipulation, through a tryptophan (TRP) depletion by diet in Wistar and Lister Hooded rats, modulates compulsive drinking in schedule-induced polydipsia (SIP) and locomotor activity in the open-field test. The levels of dopamine, noradrenaline, serotonin and its metabolite were......-depleted HD Wistar rats, while the LD Wistar and the Lister Hooded rats did not exhibit differences in SIP. In contrast, the TRP-depleted Lister Hooded rats increased locomotor activity compared to the non-depleted rats, while no differences were found in the Wistar rats. Serotonin 2A receptor binding...

Supercritical fluid extraction of uranium from tissue paper matrix using organic extractants

International Nuclear Information System (INIS)

Kanekar, A.S.; Bhattacharyya, A.; Pathak, P.N.; Mohapatra, P.K.; Manchanda, V.K.

2009-01-01

Direct extraction of dried uranyl nitrate from tissue paper matrix was carried out using supercritical carbon dioxide modified with methanol solutions of extractants such as tri-n-butyl phosphate (TBP) and di-n-hexyl octanamide (DHOA)). The effects of temperature, pressure, extractant and nitric acid concentration on the extraction of uranyl ion were investigated. (author)

Friction, Wear, and Evaporation Rates of Various Materials in Vacuum to 10(exp -7) mm Hg

Science.gov (United States)

Buckley, Donald H.; Swikert, Max; Johnson, Robert L.

1961-01-01

The requirements for bearings and seals to operate in the environment of space dictate a new area for lubrication research. The low ambient pressures encountered in space can be expected to influence the behavior of oil, grease, and solid-film lubricants. The property of these materials most significantly affected by low ambient pressures is the evaporation rate. Various investigators have therefore measured the evaporation rates of oils and greases in vacuum as one method of establishing their relative merit for space applications (1-3). The results of this work have given some indication as to the oils and greases with the greatest stability at reduced ambient pressures. Only limited experimental work, however, has been reported in the literature for inorganic solids and soft metals which have potential use as solid lubricant films or coatings for hard alloy substrates [e.g. Reference ( 4 )]. In general, the evaporation rates of these materials would be lower than those of oils and greases. These films might therefore be very attractive as lubricants for high vacuum service.

Thermal contact resistance measurement of conduction cooled binary current lead joint block in cryocooler based self field I-V characterization facility

Energy Technology Data Exchange (ETDEWEB)

Kundu, Ananya, E-mail: ananya@ipr.res.in; Das, Subrat Kumar; Agarwal, Anees Bano Pooja; Pradhan, Subrata [Institute for Plasma Research, Bhat, Gandhinagar, Gujarat 382428 (India)

2016-05-23

In the present study thermal resistance of conduction cooled current lead joint block employing two different interfacial material namely AlN sheet and Kapton Film have been studied in the temperature range 5K-35K. In each case, the performance of different interlayer materials e.g. Indium foil for moderately pressurized contacts (contact pressure <1 MPa), and Apiezon N Grease, GE varnish for low pressurized contact (contact pressure <1 MPa) is studied. The performances of AlN joint with Indium foil and with Apeizon N Grease are studied and it is observed that the contact resistance reduces more with indium foil as compared to greased contact. The contact resistance measurements of Kapton film with Apiezon N grease and with GE varnish were also carried out in the same temperature range. A comparative study of AlN joint with Indium foil and Kapton with GE varnish as filler material is carried out to demonstrate better candidate material among Kapton and AlN for a particular filler material in the same temperature range.

Extraction, fatty acid profile and antioxidant activity of sesame extract (Sesamum Indicum L.

Directory of Open Access Journals (Sweden)

R. H. R. Carvalho

2012-06-01

Full Text Available This article carried out the extraction of sesame oil by using three extraction techniques: supercritical fluid extraction (SFE, Soxhlet and sequential extraction. The SFE was performed using supercritical carbon dioxide (SC-CO2 as solvent and ethanol as cosolvent. Tests were performed at 20 MPa, 35ºC and a flow rate of 2.5 g CO2/min with a total extraction time of 210 minutes. The Soxhlet extraction was performed for 8 hours, using petroleum ether and ethanol as solvents, until the exhaustion of the oil contained in the seeds. The sequential extraction used ethyl ether, ethanol and water as solvents. The Soxhlet extraction was the most effective (58.93%, while the SFE technique obtained 26.47% as the best result. The antioxidant activity (AA was determined by the β-carotene/linoleic acid system, with good oxidation inhibition percentages (29.32-83.49% for all the extracts. The main fatty acids (FA in sesame oil were oleic and linoleic acids.

Organically modified clay removes oil from water

International Nuclear Information System (INIS)

Alther, G.R.

1995-01-01

When bentonite or other clays and zeolites are modified with quaternary amines, they become organophilic. Such modified bentonites are used to remove mechanically emulsified oil and grease, and other sparingly soluble organics. If the organoclay is granulated, it is placed into a liquid phase carbon filter vessel to remove FOG's and chlorinated hydrocarbons. In this application the clay is mixed with anthrazite to prevent early plugging of the filter by oil or grease droplets. In batch systems a powered organoclay is employed. Types of oil found in water can include fats, lubricants, cutting fluids, heavy hydrocarbons such as tars, grease, crude oil, diesel oils; and light hydrocarbons such as kerosene, jet fuel, and gasoline

determination of lipophilic extractives in ionic liquid extracts

African Journals Online (AJOL)

dell

Chem. 9: 63-69. Freire CSR, Pinto PCR, Santiago AS,. Silvestre AJD, Evtuquin DV and Neto. CP 2006a Comparative study of lipophilic extractives of hardwoods and corresponding ECF bleached kraft pulps. BioResources. 1: 3-17. Freire CSR, Silvestre AJD and Neto CP. 2005. Lipophilic extractives in. Eucalyptus globulus.

Influence of Extraction Parameters on Hydroalcohol Extracts of the ...

African Journals Online (AJOL)

The parameter that had the greatest influence on extraction process was alcohol concentration ... rules and processing steps [2]. As part .... Table 1: Extractive batch nnumbers with the respective factors and levels studied in the factorial design.

Electromembrane extraction

DEFF Research Database (Denmark)

Huang, Chuixiu; Chen, Zhiliang; Gjelstad, Astrid

2017-01-01

Electromembrane extraction (EME) was inspired by solid-phase microextraction and developed from hollow fiber liquid-phase microextraction in 2006 by applying an electric field over the supported liquid membrane (SLM). EME provides rapid extraction, efficient sample clean-up and selectivity based...

Vacuum extraction

DEFF Research Database (Denmark)

Maagaard, Mathilde; Oestergaard, Jeanett; Johansen, Marianne

2012-01-01

Objectives. To develop and validate an Objective Structured Assessment of Technical Skills (OSATS) scale for vacuum extraction. Design. Two-part study design: Primarily, development of a procedure-specific checklist for vacuum extraction. Hereafter, validation of the developed OSATS scale for vac...

Binary Solvent Extraction System and Extraction Time Effects on Phenolic Antioxidants from Kenaf Seeds (Hibiscus cannabinus L.) Extracted by a Pulsed Ultrasonic-Assisted Extraction

OpenAIRE

Yu Hua Wong; Hwee Wen Lau; Chin Ping Tan; Kamariah Long; Kar Lin Nyam

2014-01-01

The aim of this study was to determine the best parameter for extracting phenolic-enriched kenaf (Hibiscus cannabinus L.) seeds by a pulsed ultrasonic-assisted extraction. The antioxidant activities of ultrasonic-assisted kenaf seed extracts (KSE) were determined by a 2,2-diphenyl-1-picrylhydrazyl (DPPH) radical scavenging capacity assay, 2,2′-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) (ABTS) radical scavenging assay, β -carotene bleaching inhibition assay, and ferric reducing antioxi...

Lipase-producing fungi for potential wastewater treatment and ...

African Journals Online (AJOL)

The use of fungal biomass as a lipase biocatalyst represents an attractive approach for the treatments of oil wastewater as well as for the production of biodiesel from oil and residual grease, due to its greater stability, possibility of reuse, and lower cost. In this work, 20 filamentous fungi were isolated from the grease trap ...

Presence of radioactive dusts over Calcutta

Energy Technology Data Exchange (ETDEWEB)

Chatterjee, S

1954-01-01

Particles collected from the grease of airplanes since April 8, 1954, and from the rain water of April 29, 1954, possess detectable ..beta..-activity but no ..cap alpha..- or ..gamma..-activity. From one grease sample a max. ..beta..-energy of 0.5 MeV was found. The activity is attributed to recent H-bomb detonations in the Pacific Ocean.

Extraction and identification of flavonoids from parsley extracts by HPLC analysis

Science.gov (United States)

Stan, M.; Soran, M. L.; Varodi, C.; Lung, I.

2012-02-01

Flavonoids are phenolic compounds isolated from a wide variety of plants, and are valuable for their multiple properties, including antioxidant and antimicrobial activities. In the present work, parsley (Petroselinum crispum L.) extracts were obtained by three different extraction techniques: maceration, ultrasonic-assisted and microwave-assisted solvent extractions. The extractions were performed with ethanol-water mixtures in various ratios. From these extracts, flavonoids like the flavones apigenin and luteolin, and the flavonols quercetin and kaempferol were identified using an HPLC Shimadzu apparatus equipped with PDA and MS detectors. The separation method involved a gradient step. The mobile phase consisted of two solvents: acetonitrile and distilled water with 0.1% formic acid. The separation was performed on a RP-C18 column.

Gravitational wave extraction based on Cauchy-characteristic extraction and characteristic evolution

Energy Technology Data Exchange (ETDEWEB)

Babiuc, Maria [Department of Physics and Astronomy, University of Pittsburgh, Pittsburgh, PA 15260 (United States); Szilagyi, Bela [Department of Physics and Astronomy, University of Pittsburgh, Pittsburgh, PA 15260 (United States); Max-Planck-Institut fuer Gravitationsphysik, Albert-Einstein-Institut, Am Muehlenberg 1, D-14476 Golm (Germany); Hawke, Ian [Max-Planck-Institut fuer Gravitationsphysik, Albert-Einstein-Institut, Am Muehlenberg 1, D-14476 Golm (Germany); School of Mathematics, University of Southampton, Southampton SO17 1BJ (United Kingdom); Zlochower, Yosef [Department of Physics and Astronomy, and Center for Gravitational Wave Astronomy, University of Texas at Brownsville, Brownsville, TX 78520 (United States)

2005-12-07

We implement a code to find the gravitational news at future null infinity by using data from a Cauchy code as boundary data for a characteristic code. This technique of Cauchy-characteristic extraction (CCE) allows for the unambiguous extraction of gravitational waves from numerical simulations. We first test the technique on non-radiative spacetimes: Minkowski spacetime, perturbations of Minkowski spacetime and static black hole spacetimes in various gauges. We show the convergence and limitations of the algorithm and illustrate its success in cases where other wave extraction methods fail. We further apply our techniques to a standard radiative test case for wave extraction, a linearized Teukolsky wave, presenting our results in comparison to the Zerilli technique, and we argue for the advantages of our method of extraction.

About the Little Red Riding Hood, Durex and anger: production, meaning and reception of one fairy tale and one commercial ad

Directory of Open Access Journals (Sweden)

Dragana Antonijević

2016-03-01

Full Text Available By applying the semiological analysis, this paper considers planned and unplanned readings of a provocative domestic commercial, which, in order to convey its message, transposed the Little Red Riding Hood’s character in accordance with the advertised product – Durex condoms. This commercial caused furious reactions of parents who took legal action for breaching the Law on public advertising and, especially, "harming children’s sensibility and integrity". Provocative billboards also caused numerous comments in the daily newspapers, in the Internet chat rooms, with some considering the commercial vulgar and offensive and others having no problem with it, adding that the ones who took offence belonged to those puritan and conservative layers of the society. In order to discover the reasons to this kind of reactions, I started with researching how the commercial was made and what kind of message it offered. Next, I reconsidered the meaning of the very fairy tale "The Red Riding Hood". Its original version, which contains open sexual allusions, is quite different to the changed versions offered by Charles Perrault and the Grimm brothers. Their versions can be seen as fakelore, since they outrageously intervened on the plot and the meaning of the original fairy tale. However, since the Grimm brothers’ version is the most popular, it is a fact that our public reacted with such anger led by the meaning of their version, which accentuates overeating and cannibalism, and not sexual development of girls, which is the basic message of the original version. This is where the "communicational noise" that led to those negative reactions came from. By discovering the true meaning of the tale, the answer is given to the question whether the advertising agency made a slip up, or it had actually found the right way to communicate the hidden message of the tale, and at the same time ruin the advertising campaign for which it was used. In the end, range and

Solvent extraction: the coordination chemistry behind extractive metallurgy.

Science.gov (United States)

Wilson, A Matthew; Bailey, Phillip J; Tasker, Peter A; Turkington, Jennifer R; Grant, Richard A; Love, Jason B

2014-01-07

The modes of action of the commercial solvent extractants used in extractive hydrometallurgy are classified according to whether the recovery process involves the transport of metal cations, M(n+), metalate anions, MXx(n-), or metal salts, MXx into a water-immiscible solvent. Well-established principles of coordination chemistry provide an explanation for the remarkable strengths and selectivities shown by most of these extractants. Reagents which achieve high selectivity when transporting metal cations or metal salts into a water-immiscible solvent usually operate in the inner coordination sphere of the metal and provide donor atom types or dispositions which favour the formation of particularly stable neutral complexes that have high solubility in the hydrocarbons commonly used in recovery processes. In the extraction of metalates, the structures of the neutral assemblies formed in the water-immiscible phase are usually not well defined and the cationic reagents can be assumed to operate in the outer coordination spheres. The formation of secondary bonds in the outer sphere using, for example, electrostatic or H-bonding interactions are favoured by the low polarity of the water-immiscible solvents.

78 FR 42929 - Foreign-Trade Zone (FTZ) 41-Milwaukee, Wisconsin, Notification of Proposed Production Activity...

Science.gov (United States)

2013-07-18

..., electric motors for exhaust/ ventilation, electric motors for downdraft range hoods, parts used on electric motors, light ballasts, transformers, magnets for range hoods, portable heaters and fans, heating.../heater units, relays, motor starters, wall switches, various switch types, lamp sockets, other electrical...

Comparative synergistic (technetium-actinide) extraction chemistry by tributylphosphate and some amide extractants

International Nuclear Information System (INIS)

Condamines, N.; Musikas, C.

1993-01-01

In nuclear fuel reprocessing, technetium (TcO 4 - ) leads to bad interferences in the extractions, being synergistically co-extracted with different actinide cations as Uranium (VI), Plutonium (IV) and Zirconium (IV). It destroys the hydrazine in the reductive partition of U and Pu, it decreases the decontamination of U and Pu from fission products. Thus, its extraction behaviour with new extractants as N,N-diakylamides is useful to be known. TcO 4 - extraction in nitric acid media is compared for TBP and different amides. The influence of nitric acidity is related to the amides formula

Comparison of low-level polycyclic aromatic hydrocarbons in sediment revealed by Soxhlet extraction, microwave-assisted extraction, and pressurized liquid extraction

International Nuclear Information System (INIS)

Itoh, Nobuyasu; Numata, Masahiko; Aoyagi, Yoshie; Yarita, Takashi

2008-01-01

We analyzed polycyclic aromatic hydrocarbons (PAHs) present in lake sediment at low levels ( -1 ) by using Soxhlet extraction (Soxhlet), microwave-assisted extraction (MAE), and pressurized liquid extraction (PLE) in combination with gas chromatography and isotope-dilution mass spectrometry. Although all extraction techniques showed good repeatability for five target PAHs (relative standard deviation MAE > Soxhlet. Differences in the results originated mainly from differences in the extraction efficiencies of the techniques for native PAHs, because all techniques gave comparable recovery yields of corresponding 13 C-labeled PAHs ( 13 C-PAHs) (51-84%). Since non-negligible amounts of both native PAHs and 13 C-PAHs were re-adsorbed on matrix in MAE, not only recovery yields of 13 C-PAHs but also efficiencies of extraction of native PAHs should be examined to evaluate the appropriateness of any analytical procedures

30 CFR 750.21 - Coal extraction incidental to the extraction of other minerals.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 3 2010-07-01 2010-07-01 false Coal extraction incidental to the extraction of... ENFORCEMENT, DEPARTMENT OF THE INTERIOR INDIAN LANDS PROGRAM REQUIREMENTS FOR SURFACE COAL MINING AND RECLAMATION OPERATIONS ON INDIAN LANDS § 750.21 Coal extraction incidental to the extraction of other minerals...

Extraction of Glycyrrhizic Acid from Glycyrrhiza uralensis Using Ultrasound and Its Process Extraction Model

Directory of Open Access Journals (Sweden)

Jiangqing Liao

2016-10-01

Full Text Available This work focused on the intensification of extraction process of glycyrrhizic acid (GA from Glycyrrhiza uralensis using ultrasound-assisted extraction (UAE method. Various process parameters such as ultrasonic power, ultrasonic frequency, extraction temperature, and extraction time which affect the extraction yield were optimized. The results showed that all process parameters had exhibited significant influences on the GA extraction. The highest GA yield of 217.7 mg/g was obtained at optimized parameters of 125 W, 55 kHz, 25 °C, and 10 min. Furthermore, the extraction kinetics model of this process was also investigated based on Fick’s first law available in the literature. Kinetic parameters such as equilibrium concentration (Ce and integrated influence coefficient (λ for different ultrasonic powers, ultrasonic frequencies, and extraction temperatures were predicted. Model validations were done successfully with the average of relative deviation between 0.96% and 4.36% by plotting experimental and predicted values of concentration of GA in extract. This indicated that the developed extraction model could reflect the effectiveness of the extraction of GA from Glycyrrhiza uralensis and therefore serve as the guide for comprehending other UAE process.

Investigation of cultivated lavender (Lavandula officinalis L. extraction and its extracts

Directory of Open Access Journals (Sweden)

Nađalin Vesna

2014-01-01

Full Text Available In this study essential oil content was determined in lavender flowers and leaves by hydrodistillation. Physical and chemical characteristics of the isolated oils were determined. By using CO2 in supercritical state the extraction of lavender flowers was performed with a selected solvent flow under isothermal and isobaric conditions. By the usage of gas chromatography in combination with mass spectrometry (GC/MS and gas chromatography with flame ionisation detector (GC/FID the qualitative and quantitative analysis of the obtained essential oil and supercritical extracts (SFE was carried out. Also, the analysis of individual SFE extracts obtained during different extraction times was performed. It turned out that the main components of the analysed samples were linalool, linalool acetate, lavandulol, caryophyllene oxide, lavandulyl acetate, terpinen-4-ol and others. Two proposed models were used for modelling the extraction system lavender flower - supercritical CO2 on the basis of experimental results obtained by examining the extraction kinetics of this system. The applied models fitted well with the experimental results.

Di-4-octylphenylphosphoric acid as extractant : extraction of vanadium (IV) and beryllium

International Nuclear Information System (INIS)

Gajankush, R.B.

1976-01-01

The extraction of vanadium and beryllium has been studied using di-4-octylphenyl phosphoric acid (DOPPA) as metal extractant. The factors which affect the extraction have been studied in detail. An attempt has been made to clarify the mechanism of extraction and compare the results with those reported for di-2-ethylhexyl phosphoric acid (DEHPA). In the case of vanadium it was found that vanadium (IV) is more suitable for extraction. Synergistic extractionwas observed in the presence of neutral organophosphorous compounds like tri-n-butyl phosphate (TBP), dibutyl butyl phosphate (DBBP) and tri-n-octyl phosphine oxide (TOPO). The possibility of separating vanadium and uranium when they are present together in leach solutions has also been studied. The extraction of beryllium was found to be a slow process. The factors controlling the rate as well as the extent of extraction have been investigated. However, the results showed that in both respects DOPPA is better than DEHPA which was earlier studied by other authors. The separation of aluminium from beryllium has also been studied. (author)

Characterization of Arachis hypogaea L. oil obtained from different extraction techniques and in vitro antioxidant potential of supercritical fluid extraction extract

Directory of Open Access Journals (Sweden)

Rishika Chauhan

2016-01-01

Full Text Available Aim: The present investigation was aimed to characterize the fixed oil of Arachis hypogaea L. using five different extraction methods: Supercritical fluid extraction (SFE, ultrasound assistance extraction, soxhlet extraction, solvent extraction, and three phase partitioning method. Materials and Methods: The SFE conditions (temperature, pressure, and volume of CO 2 were optimized prior for better yield. The extracted oils were analyzed and compared for their physiochemical parameters, high-performance thin layer chromatography (HPTLC, gas chromatography-mass spectrometry (GC-MS, and Fourier transform infrared spectrometry (FT-IR fingerprinting. Anti-oxidant activity was also determined using DPPH and superoxide scavenging method. Results: The main fatty acids were oleic, linoleic, palmitic, and stearic acids as obtained by GC-MS. HPTLC analysis revealed the presence of similar major components in chromatograms. Similarly, the pattern of peaks as obtained in FT-IR and GC-MS spectra of same oils by different extraction methods was superimposable. Conclusion: Analysis reported that the fixed oil of A. hypogaea L. is a good source of unsaturated fatty acid, mainly n-6 and n-9 fatty acid with a significant antioxidant activity of oil obtained from SFE extraction method.

Kinetics Extraction Modelling and Antiproliferative Activity of Clinacanthus nutans Water Extract

Directory of Open Access Journals (Sweden)

Farah Nadiah Mohd Fazil

2016-01-01

Full Text Available Clinacanthus nutans is widely grown in tropical Asia and locally known “belalai gajah” or Sabah snake grass. It has been used as a natural product to treat skin rashes, snake bites, lesion caused by herpes, diabetes, fever, and cancer. Therefore, the objectives of this research are to determine the maximum yield and time of exhaustive flavonoids extraction using Peleg’s model and to evaluate potential of antiproliferative activity on human lung cancer cell (A549. The extraction process was carried out on fresh and dried leaves at 28 to 30°C with liquid-to-solid ratio of 10 mL/g for 72 hrs. The extracts were collected intermittently analysed using mathematical Peleg’s model and RP-HPLC. The highest amount of flavonoids was used to evaluate the inhibitory concentration (IC50 via 2D cell culture of A549. Based on the results obtained, the predicted maximum extract density was observed at 29.20 ± 14.54 hrs of extraction (texhaustive. However, the exhaustive time of extraction to acquire maximum flavonoids content exhibited approximately 10 hrs earlier. Therefore, 18 hrs of extraction time was chosen to acquire high content of flavonoids. The best antiproliferative effect (IC50 on A549 cell line was observed at 138.82 ± 0.60 µg/mL. In conclusion, the flavonoids content in Clinacanthus nutans water extract possesses potential antiproliferative properties against A549, suggesting an alternative approach for cancer treatment.

Separation of digoxin by luiquid-luiquid extraction from extracts of foxglove secondary glycosides

Directory of Open Access Journals (Sweden)

Novković Vesna V.

2014-01-01

Full Text Available The present study deals with the extraction of digoxin (Dgx from chloroform and trichloroethylene extracts of the secondary glycosides of fermented foxglove (Digitalis lanata Ehrh. foliage by liquid-liquid extraction. The extraction degree (ED of Dgx achieved by maceration and percolation using 10% vol. aqueous ethanol solutions were higher than 95%. Using trichlorethylene and chloroform, the ED of Dgx of about 100% and 96%, respectively from the liquid ethanolic extracts (macerate or percolate were achieved by the four-cycle extraction. Fifteen separating funnels were employed for the liquid-liquid extraction. Three different four-component two-phase systems (ethanol:water - chloroform:ethyl acetate, ethanol:water - chloroform:trichloroethylene and ethanol:water - trichloroethylene:ethyl acetate were tested as an extracting solvent to get the final product having more than 98% of Dgx. The initial amount of the chloroform or trichloroethylene extract in the light phase was varied between 5 and 25 g/L, while the volume ratio of light and heavy phases was in the range of 1:1 to 1:2. The best Dgx yield of 98% was achieved with the system ethanol:water - chloroform:trichloroethylene 35:15:20:30 at the volume ratio of the phases of 1:1.1 and at the initial amount of the extract of 15 g/L. Purity of the separated digoxin was 99.8 %. [Projekat Ministarstva nauke Republike Srbije, br. TR-34012

76 FR 55648 - Sunsations Inc., Provisional Acceptance of a Settlement Agreement and Order

Science.gov (United States)

2011-09-08

...) 504-7809. SUPPLEMENTARY INFORMATION: The text of the Agreement and Order appears below. Dated... upper outerwear products with drawstrings at the hood or neck. Specifically, from March 2008 through... the hood or neck (sweatshirts), manufactured by GJC International and Top Image USA. From May 2009...

Extraction of uranium with emulsion membrane process use tributylphosphate extractant

International Nuclear Information System (INIS)

Basuki, K.T.; Sudibyo, R.; Bambang EHB; Muhadi, A.W.

1996-01-01

To increase the effectiveness of extraction process with so for to occur, it was tried the extraction with a couple of extraction and stripping process. This couple process was called liquid membrane emulsion. As membrane was used mix surfactant (Span-80), tributylphosphate in kerosene, natrium carbonate, while as a feeder was uranium solution with 500 concentration ppm in 0.5 - 3 M nitrate acid. In this experiment the variable investigated were % surfactant (1 - 5 %), rotary speed for membrane making (2,500 - 10.000 rpm). The optimal condition result of experiment were 5 % surfactant, 3 M nitrate acid, rotary speed 10.000 rpm and (Kd eksU ) 57 %, and (Kd strippU ) 87 %, Kd eksU at liquid-liquid extraction is 44 %. (author)

Extraction of copper zinc and iron from hydrochloric acid solutions by means of different extractants

Energy Technology Data Exchange (ETDEWEB)

Zhivkova, Svetlana [Institute of Chemical Engineering - Bulgarian Academy of Sciences, Sofia (Bulgaria)

2011-07-01

The extraction of copper, zinc and iron from hydrochloric acid solutions has been studied. The experiments have been carried out using various solvents, involving different extraction mechanisms – solvating, anion-exchange, cation-exchange, bifunctional . Mixtures of these extractants have been also used. The extraction properties of these extractant mixtures toward copper, zinc and iron, the effect of used modifiers and diluents have been also investigated. Key words: Copper, Zinc, Iron, Extraction, Extractant, Modifier, Diluent.

Statement on hooding

DEFF Research Database (Denmark)

Alempijevic, D.; Beriashvili, J.; Beynon, J.

2011-01-01

and/or CIDT, forensic experts base their opinions on the extent to which the sum total of physical and/or psychological evidence corroborates an individual’s allegations of abuseand on evidence of physical and mental pain and disabilities associated with the alleged abuse. In our opinion...

Distillation of shale

Energy Technology Data Exchange (ETDEWEB)

Anderson, J

1877-01-05

The retort consists of a trough fitted with a hood, the edges of which hood dip into a channel of water formed round the sides of the trough, and thereby seal the retort. The shale is introduced at one end of the hood through a double-valved inlet hopper, and is moved along the retort by transverse scrapers or paddles. At the other end it falls through a double-valved outlet upon a set of firebars which carry it along under the retort, where either alone or in admixture with other fuel it is used for heating the vessel. The vapors from the shale pass off through pipes in the hood, or an inverted channel may be formed along the center of the hood for collecting the vapors from different parts of the vessel. The scrapers are worked by rocking shafts supported on bearings in the edges of the trough, and are made to feather when moving in a direction from the discharged end. Levers from the rocking shafts project down into the water channel, where they are connected with horizontal bars made to reciprocate longitudinally by suitable means, thus working the scrapers without using stuffing-boxes. Rotating scrapers may be substituted for the reciprocating ones.

Biological activity and safety of Tripterygium extract prepared by sodium carbonate extraction.

Science.gov (United States)

Fang, Wei; Peng, Fan; Yi, Tao; Zhang, Cong; Wan, Chunxi; Xu, Huibi; Lam, Christopher Waikei; Yang, Xiangliang

2012-09-17

The commercial preparation named “Tripterygium glycosides” prepared by column chromatography has been used for the treatment of inflammatory and autoimmune diseases with significant efficacy but concurrent toxicity. The aim of this study was to reduce the toxicity of Tripterygium extracts, using cytotoxicity and anti-inflammatory activity of the three principal active components of Tripterygium wilfordii Hook. F. (TWHF)as guiding parameters. Column chromatography was replaced by sodium carbonate extraction for removing the acidic compounds and enriching epoxyditerpenoids and alkaloids in the extract. Results showed that the therapeutic index (IC50/EC50) on murine macrophage Raw 264.7 cells and rat mesangial HBZY-1 cells of the extract prepared by sodium carbonate extraction was significantly higher than that of Tripterygium glycosides(0.8 and 5.2 vs. 0.3 and 2.6, p sodium carbonate extraction may represent a potentially optimal source of medicine with good therapeutic index.

RED WINE EXTRACT OBTAINED BY MEMBRANE-BASED SUPERCRITICAL FLUID EXTRACTION: PRELIMINARY CHARACTERIZATION OF CHEMICAL PROPERTIES.

Directory of Open Access Journals (Sweden)

W. Silva

Full Text Available ABSTRACT This study aims to obtain an extract from red wine by using membrane-based supercritical fluid extraction. This technique involves the use of porous membranes as contactors during the dense gas extraction process from liquid matrices. In this work, a Cabernet Sauvignon wine extract was obtained from supercritical fluid extraction using pressurized carbon dioxide as solvent and a hollow fiber contactor as extraction setup. The process was continuously conducted at pressures between 12 and 18 MPa and temperatures ranged from 30 to 50ºC. Meanwhile, flow rates of feed wine and supercritical CO2 varied from 0.1 to 0.5 mL min-1 and from 60 to 80 mL min-1 (NCPT, respectively. From extraction assays, the highest extraction percentage value obtained from the total amount of phenolic compounds was 14% in only one extraction step at 18MPa and 35ºC. A summarized chemical characterization of the obtained extract is reported in this work; one of the main compounds in this extract could be a low molecular weight organic acid with aromatic structure and methyl and carboxyl groups. Finally, this preliminary characterization of this extract shows a remarkable ORAC value equal to 101737 ± 5324 µmol Trolox equivalents (TE per 100 g of extract.

Development of a signal-extraction scheme for resonant sideband extraction

International Nuclear Information System (INIS)

Kokeyama, K; Kawazoe, F; Sugamoto, A; Somiya, K; Sato, S; Kawamura, S

2008-01-01

As a future plan, an advanced gravitational-wave detector will employ an optical configuration of resonant sideband extraction (RSE), achieved with an additional mirror at the signal-detection port of the power-recycled Fabry-Perot Michelson interferometer. To control the complex coupled cavity system, one of the most important design issues is how to extract the longitudinal control signals of the cavities. We have developed a new signal-extraction scheme which provides an appropriate sensing matrix. The new method uses two sets of sidebands: one of the sideband components satisfies the critical coupling condition for the RSE interferometer and reaches the signal-extraction port, and the other sideband is completely reflected by the Michelson interferometer. They provide a diagonalized sensing matrix and enable the RSE control to be robust

Selective Extraction of Organic Contaminants from Soil Using Pressurised Liquid Extraction

Directory of Open Access Journals (Sweden)

Rozita Osman

2013-01-01

Full Text Available This study focuses on the application of sorbents in pressurised liquid extraction (PLE cell to establish a selective extraction of a variety of organic contaminants (polycyclic aromatic hydrocarbons (PAHs, chlorpyrifos, phenol, pentachlorophenol, and sterols from soil. The selectivity and efficiency of each sorbent depend on the properties of the material, extracting solvent, capacity factor, organic compounds of interest, and PLE operating parameters (temperature, pressure, and extraction time. Several sorbents (silica, alumina, and Florisil were evaluated and with the proper choice of solvents, polar and nonpolar compounds were successfully separated in two fractions. Nonpolar compounds (PAHs, chlorpyrifos, and pentachlorophenol were recovered in the first fraction using a polar sorbent such as Florisil or alumina, and n-hexane as eluting solvent, while more polar compounds (phenol and sterols were recovered in the second fraction using methanol. Silica (5 g was found to be effective for selective extraction with the satisfactory recoveries for all compounds (PAHs from 87.1–96.2%, chlorpyrifos 102.9%, sterols from 93.7–100.5%, phenol 91.9%, and pentachlorophenol 106.2%. The efficiency and precision of this extraction approach and the existing EPA Method 3545 were compared.

National Writing Project's Multimodal Literacies and Teacher Collaboration: Enhanced Student Learning on Global Social Issues

Science.gov (United States)

Iyengar, Kalpana; Hood, Caleb

2016-01-01

Iyengar and Hood, both teacher consultants with the San Antonio Writing Project (SAWP), and instructors of an undergraduate society and social issues class, collaborated to enhance their undergraduate students' writing experiences using the National Writing Project model (Lieberman & Wood, 2003). Iyengar and Hood used strategies such as…

77 FR 71163 - Federal Motor Vehicle Safety Standards; Windshield Zone Intrusion

Science.gov (United States)

2012-11-29

... fully determined. Those influences are more stringent U.S. Corporate Average Fuel Economy (CAFE... materials to meet CAFE standards, including materials in and around the hoods of vehicles. Hood design could... evolves in response to CAFE standards. Additionally, in November 2008, the World Forum for Harmonization...

Aldrich 1991, Clarke 1986, Nesis 1987, Roelev

African Journals Online (AJOL)

spamer

either beak; d = length of the baseline in profile, lower beak; e ... beak; HdL (= g) = hood length in the midline, either beak; JW ..... edge of hood with broad deep notch in the midline. ... rior tip to form shallow and hollow cone (CoLI 1.20),. 116.

Effect of extraction method and orientin content on radio-protective effect of tulsi extracts

Energy Technology Data Exchange (ETDEWEB)

Tiwari, Mrinalini; Dwarakanath, B. S.; Agrawala, Paban K., E-mail: pkagrawal@gmail.com [Institute of Nuclear Medicine and Allied Sciences, Delhi (India); Murugan, R.; Parimelazhagan, T. [Department of Botany, Bharathiar University, Coimbatore (India); Uma Devi, P. [ARA-B-3SA, Plavilakonam,Trivandrum (India); Gota, V.; Sarin, R. K. [Advanced Centre for Treatment Research and Education in Cancer, Navi Mumbai (India)

2014-07-01

Extract of tulsi leaves (Ocimum sanctum) has been reported for its radioprotective efficacy. In our initial studies we observed significant variation in the survival of irradiated mice with different batches of tulsi extracts and therefore we employed different extraction methods on leaves collected during various seasons from different localities to study any variation in the radioprotective efficacy. Orientin, a component of tulsi extract, was considered a marker. Mice whole body survival (at 10 Gy lethal whole body irradiation) study and day 11 endo-CFU-s assay (at 5 Gy WBI) were performed employing 3 treatment schedules, 50 mg/kg or 25 mg/kg b.w (single injection, 30 min irradiation), and 10 mg/kgb.w (one injection per day for 5 day, last injection being 30 min before irradiation). Single dose of 25 mg/kg b.w (both aqueous and alcoholic) did not provide any significant survival benefit. The orientin concentrations in the extracts tested varied from 3.3 to 9.91 mg/g extract as studied by HPLC method. With a single administration (i.p) of 50 mg/kg, the aqueous extract from leaves of monsoon season had an orientin content of 9.91 mg/g extract and gave a survival of 60% with a CFU-s count of 37, while extract of leaf summer leaves had an orientin content of 4.15 mg/g extract and gave a survival of 50% with a CFU-s count of 11.6. At the same dose (50 mg/kg), the aqueous extract from the winter season had an orientin content of 3.30 mg/g extract and gave 25% survival with a CFU-s count of 19, while the ethanolic extract had an orientin content of 7.70 mg/g extract and gave a survival of 50% with a CFU-s count of 13. These observations suggest that different climatic factors, orientin content and the doses of administration are important factors regulating radioprotection afforded by different extracts of tulsi. (author)

Pressurized Hot Water Extraction of anthocyanins from red onion: A study on extraction and degradation rates

Energy Technology Data Exchange (ETDEWEB)

Petersson, Erik V.; Liu Jiayin; Sjoeberg, Per J.R.; Danielsson, Rolf [Uppsala University, Department of Physical and Analytical Chemistry, P.O. Box 599, SE-751 24, Uppsala (Sweden); Turner, Charlotta, E-mail: Charlotta.Turner@kemi.uu.se [Uppsala University, Department of Physical and Analytical Chemistry, P.O. Box 599, SE-751 24, Uppsala (Sweden)

2010-03-17

Pressurized Hot Water Extraction (PHWE) is a quick, efficient and environmentally friendly technique for extractions. However, when using PHWE to extract thermally unstable analytes, extraction and degradation effects occur at the same time, and thereby compete. At first, the extraction effect dominates, but degradation effects soon take over. In this paper, extraction and degradation rates of anthocyanins from red onion were studied with experiments in a static batch reactor at 110 deg. C. A total extraction curve was calculated with data from the actual extraction and degradation curves, showing that more anthocyanins, 21-36% depending on the species, could be extracted if no degradation occurred, but then longer extraction times would be required than those needed to reach the peak level in the apparent extraction curves. The results give information about the different kinetic processes competing during an extraction procedure.

Enzyme assisted extraction of biomolecules as an approach to novel extraction technology: A review.

Science.gov (United States)

Nadar, Shamraja S; Rao, Priyanka; Rathod, Virendra K

2018-06-01

An interest in the development of extraction techniques of biomolecules from various natural sources has increased in recent years due to their potential applications particularly for food and nutraceutical purposes. The presence of polysaccharides such as hemicelluloses, starch, pectin inside the cell wall, reduces the extraction efficiency of conventional extraction techniques. Conventional techniques also suffer from low extraction yields, time inefficiency and inferior extract quality due to traces of organic solvents present in them. Hence, there is a need of the green and novel extraction methods to recover biomolecules. The present review provides a holistic insight to various aspects related to enzyme aided extraction. Applications of enzymes in the recovery of various biomolecules such as polyphenols, oils, polysaccharides, flavours and colorants have been highlighted. Additionally, the employment of hyphenated extraction technologies can overcome some of the major drawbacks of enzyme based extraction such as longer extraction time and immoderate use of solvents. This review also includes hyphenated intensification techniques by coupling conventional methods with ultrasound, microwave, high pressure and supercritical carbon dioxide. The last section gives an insight on application of enzyme immobilization as a strategy for large scale extraction. Immobilization of enzymes on magnetic nanoparticles can be employed to enhance the operational performance of the system by multiple use of expensive enzymes making them industrially and economically feasible. Copyright © 2018 Elsevier Ltd. All rights reserved.

Evaluation of urinary cortisol excretion by radioimmunoassay through two methods (extracted and non-extracted)

International Nuclear Information System (INIS)

Fonte Kohek, M.B. da; Mendonca, B.B. de; Nicolau, W.

1993-01-01

The objective of this paper is to compare the feasibility, sensitivity and specificity of both methods (extracted versus non-extracted) in the hypercortisolism diagnosis. It used Gamma Coat 125 cortisol Kit provided by Clinical Assays, Incstar, USA, for both methods extracting it with methylene chloride in order to measure the extracted cortisol. It was performed 32 assays from which it was obtained from 0.1 to 0.47 u g/d l of sensitivity. The intra-run precision was varied from 8.29 +- 3.38% and 8.19 +-4.72% for high and low levels, respectively for non-extracted cortisol, and 9.72 +- 1.94% and 9.54 +- 44% for high and low levels, respectively, for extracted cortisol. The inter-run precision was 15.98% and 16.15% for high level of non-extracted cortisol, respectively. For the low level it obtained 17.25% and 18.59% for non-extracted and extracted cortisol respectively. It was evaluated 24-hour urine basal samples from 43 normal subjects, and 53 obese (body mass index > 30) and 53 Cushing's syndrome patients. The sensitivity of the methods were similar (100% and 98.1% for non-extracted and extracted methods, respectively) and the specificity was the same for both methods (100%). It was noticed a positive correlation between the two methods in all the groups studied (p s syndrome. (author)

Radiation exposure in the use of camping gas lamps

International Nuclear Information System (INIS)

Elmer, E.

1985-01-01

The gas lamps used during camping are provided with so-called incandescent hood. To increase the luminous power, they include an average of 330 mg of thorium oxide (Th-nat), which corresponds to an overall activity of about 36 nCi (1.3 kBq). The assessment of radiological risks of campers showed that the radiation doses from external irradiation or ingestion of the existing activity may be neglected. However, special attention must be given to inhalation because the incandescent hood embrittles after while and in the course of replacement may fall to dust which might be breathed in. A person who replaces the hood carelessly twice can reach the maximum permissible annual inhalation rate (=1 nCi Th-nat) this way. This also applies to the maximum permissible surface contamination. In Switzerland, thorium incandescent hood may only be sold for general use on the condition that the purchaser is instructed by a notice how to replacement is to be made to avoid dust. (orig./HP) [de

A decking for erecting an insulating connector

Energy Technology Data Exchange (ETDEWEB)

Chuprikov, A Ye; Lagutin, V I; Sklyarov, A A; Sukhanov, G V

1983-01-01

The decking includes a parachute like dome, made of a material impenetrable to air, an air penetrable hood, attachment elements and a branch pipe for supplying the filler. To improve the sealing of the insulating connector upon contact with the walls and the roof of the drift being isolated and to reduce the labor intensity of operations, it is equipped with a housing made in the form of a cylinder from a material impenetrable to water, an advancible vertical upright and a spring loaded panel. The housing is installed between the parachute like dome and the air penetrable hood. The extendible vertical upright is installed on the side of the air penetrable hood and by means of a movable rack mechanism is kinematically linked with the spring loaded panel, installed with the capability of interacting with the air penetrable hood. The spring loaded plate is made in the form of perforated plates which have a telescopic disengagement in the horizontal plane.

Potential of mangrove Avicennia rumphiana extract as an antioxidant agent using multilevel extraction

Science.gov (United States)

Sulmartiwi, L.; Pujiastuti, D. Y.; Tjahjaningsih, W.; Jariyah

2018-04-01

Avicennia rumphiana is one of abundant mangrove found in Indonesia. Multilevel extraction methods were simultaneously conducted to screen the antioxidant activity from mangrove. The leaves, fruits and barks were consequently extracted using n-hexane, ethyl acetate and ethanol. The presence of phenolic, flavonoids and tannins compounds were characterized by quantitative and qualitative phytochemical assay as well as the antioxidant activity was examined using DPPH-free radical scavenging assay. The phytochemical test revealed that all of the extracts showed positive result. The fruits extract exhibited the highest phenolic, flavonoid and tannin (23.86 mg/g, 13.77 mg/g and 74.63 mg/g), respectively. The extracts were further confirmed for antioxidant using IC50 value and revealed that ethyl acetate extract has antioxidant activity better than n-hexane and ethyl acetate extract. Furthermore, this study indicated that mangrove Avicennia rumphiana could be subsequently explored for other biological activities due to their potential secondary metabolites.

Phenolic Content and Antioxidant Activity of Hibiscus cannabinus L. Seed Extracts after Sequential Solvent Extraction

Directory of Open Access Journals (Sweden)

Shahid Iqbal

2012-10-01

Full Text Available A sequential solvent extraction scheme was employed for the extraction of antioxidant compounds from kenaf (Hibiscus cannabinus L. seeds. Yield of extracts varied widely among the solvents and was the highest for hexane extract (16.6% based on dry weight basis, while water extract exhibited the highest total phenolic content (18.78 mg GAE/g extract, total flavonoid content (2.49 mg RE/g extract, and antioxidant activities (p < 0.05. DPPH and hydroxyl radical scavenging, β-carotene bleaching, metal chelating activity, ferric thiocyanate and thiobarbituric acid reactive substances assays were employed to comprehensively assess the antioxidant potential of different solvent extracts prepared sequentially. Besides water, methanolic extract also exhibited high retardation towards the formation of hydroperoxides and thiobarbituric acid reactive substances in the total antioxidant activity tests (p < 0.05. As conclusion, water and methanol extracts of kenaf seed may potentially serve as new sources of antioxidants for food and nutraceutical applications.

Air-cleaning apparatus

International Nuclear Information System (INIS)

Howard, A.G.

1981-01-01

An air-cleaning, heat-exchange apparatus includes a main housing portion connected by means of an air inlet fan to the kitchen exhaust stack of a restaurant. The apparatus includes a plurality of heat exchangers through which a heat-absorptive fluid is circulated, simultaneously, by means of a suitable fluid pump. These heat exchangers absorb heat from the hot exhaust gas, out of the exhaust stack of the restaurant, which flows over and through these heat exchangers and transfers this heat to the circulating fluid which communicates with remote heat exchangers. These remote heat exchangers further transfer this heat to a stream of air, such as that from a cold-air return duct for supplementing the conventional heating system of the restaurant. Due to the fact that such hot exhaust gas is heavily grease laden , grease will be deposited on virtually all internal surfaces of the apparatus which this exhaust gas contacts. Consequently, means are provided for spraying these contacted internal surfaces , as well as the hot exhaust gas itself, with a detergent solution in which the grease is soluble, thereby removing grease buildup from these internal surfaces

Pain and chewing sensitivity during fixed orthodontic treatment in extraction and non-extraction patients.

Science.gov (United States)

Sayar, Gulsilay

2017-01-01

The aim of this study was to evaluate the differences in pain perception and chewing sensitivity between extraction and non-extraction patients. Thirty orthodontic patients (11 males, 19 females) were included in this study who were classified as extraction (n=15; 6 males, 9 females) and non-extraction patients (n=15; 7 males, 8 females). The mean age of patients were 15.10±1.83 years in non-extraction group and 15.44±0.75 years in extraction group. The patients were asked to complete the Visual Analogue Scale (VAS) questionnaire and they were asked to mark the presence or absence of sensitivity during 7 days after the first arch wire placement. Pain intensity comparison between groups was performed using the Mann-Whitney U test. The Friedman test was used to analyze within-group differences over time. There were no significant differences in pain scores between the groups. Pain levels significantly decreased between day 1 and day 3 in both the groups. No differences were found in the chewing sensitivity between the non-extraction and extraction groups. No difference in the pain perception was observed between the extraction and non-extraction patients during the 7 days after arch wire placement.

PAIN AND CHEWING SENSITIVITY DURING FIXED ORTHODONTIC TREATMENT IN EXTRACTION AND NON-EXTRACTION PATIENTS

Directory of Open Access Journals (Sweden)

Gülşilay SAYAR

2017-04-01

Full Text Available Purpose: The aim of this study was to evaluate the differences in pain perception and chewing sensitivity between extraction and non-extraction patients. Subjects and Methods: Thirty orthodontic patients (11 males, 19 females were included in this study who were classified as extraction (n=15; 6 males, 9 females and non-extraction patients (n=15; 7 males, 8 females. The mean age of patients were 15.10±1.83 years in non-extraction group and 15.44±0.75 years in extraction group. The patients were asked to complete the Visual Analogue Scale (VAS questionnaire and they were asked to mark the presence or absence of sensitivity during 7 days after the first arch wire placement. Pain intensity comparison between groups was performed using the Mann-Whitney U test. The Friedman test was used to analyze within-group differences over time. Results: There were no significant differences in pain scores between the groups. Pain levels significantly decreased between day 1 and day 3 in both the groups. No differences were found in the chewing sensitivity between the non-extraction and extraction groups. Conclusion: No difference in the pain perception was observed between the extraction and non-extraction patients during the 7 days after arch wire placement.

Supercritical carbon dioxide hop extraction

Directory of Open Access Journals (Sweden)

Pfaf-Šovljanski Ivana I.

2005-01-01

Full Text Available The hop of Magnum cultivar was extracted using supercritical carbon dioxide (SFE-as extractant. Extraction was carried out in the two steps: the first one being carried out at 150 bar and 40°C for 2.5 h (Extract A, and the second was the extraction of the same hop sample at 300 bar and 40°C for 2.5 h (Extract B. Extraction kinetics of the system hop-SFE-CO2 was investigated. Two of four most common compounds of hop aroma (α-humulene and β-caryophyllene were detected in Extract A. Isomerised α-acids and β-acids were detected too. a-Acid content in Extract B was high (that means it is a bitter variety of hop. Mathematical modeling using empirical model characteristic time model and simple single sphere model has been performed on Magnum cultivar extraction experimental results. Characteristic time model equations, best fitted experimental results. Empirical model equation, fitted results well, while simple single sphere model equation poorly approximated the results.

Plant location and extraction procedure strongly alter the antimicrobial activity of murta extracts

DEFF Research Database (Denmark)

Shene, Carolina; Reyes, Agnes K.; Villarroel, Mario

2009-01-01

plants grown nearer to the mountain (58 mg GAE/g murta), subjected to extreme summer/winter-day/night temperature changes and rainy regime. Extracts from leaves collected in the valley and coast contained 46 and 40 mg GAE/g murta, respectively. A mixture of 50% ethanol/water was the most efficient......Leaves and fruits of Murta (Ugni Molinae Turcz.) growing in three locations of Chile with diverse climatic conditions were extracted by using ethanol/water mixtures at different ratios and the antimicrobial activity was assessed. Extracts containing the highest polyphenolic content were from murta...... in extracting polyphenols, showing pure solvents-both water and ethanol-a lower extraction capacity. No correlation between antioxidant capacity and polyphenolic content was found. Extracts from Murta leaves provoked a decrease in the growing of Pseudomonas aeruginosa, Klebsiella pneumoniae and Staphylococcus...

Selectivity in extraction of copper and indium with chelate extractants

International Nuclear Information System (INIS)

Zivkovic, D.

2003-01-01

Simultaneous extraction of copper and indium with chelate extractants (LIX84 and D2E11PA) was described. Stechiometry of metal-organic complexes examined using the method of equimolar ratios resulted in CuR 2 and InR 3 forms of hydrophobic extracting species. A linear correlation was obtained between logarithm of distribution coefficients and chelate agents and pH, respectively. Selectivity is generally higher with higher concentrations of chelate agents in the organic phase, and is decreased with increase of concentration of hydrogen ions in feeding phase. (Original)

One-step extraction of polar drugs from plasma by Parallel Artificial Liquid Membrane Extraction

DEFF Research Database (Denmark)

Pilařová, Veronika; Sultani, Mumtaz; Ask, Kristine Skoglund

2017-01-01

in the pores of a thin polymeric membrane, a well-known extraction principle also used in hollow fiber liquid-phase microextraction (HF-LPME). However, the new PALME technique offers a more user-friendly setup in which the supported liquid membrane is incorporated in a 96 well plate system. Thus, high......The new microextraction technique named parallel artificial liquid membrane extraction (PALME) was introduced as an alternative approach to liquid-liquid extraction of charged analytes from aqueous samples. The concept is based on extraction of analytes across a supported liquid membrane sustained...... for extraction of polar basic drugs was developed in the present work. The basic drugs hydralazine, ephedrine, metaraminol, salbutamol, and cimetidine were used as model analytes, and were extracted from alkalized human plasma into an aqueous solution via the supported liquid membrane. The extraction...

Sensor development for in situ detection of concentration polarization and fouling of reverse osmosis membranes

Science.gov (United States)

Detrich, Kahlil T.; Goulbourne, Nakhiah C.

2009-03-01

The purpose of this research is to evaluate three polymer electroding techniques in developing a novel in situ sensor for an RO system using the electrical response of a thin film composite sensor. Electrical impedance spectroscopy (EIS) was used to measure the sensor response when exposed to sodium chloride solutions with concentrations from 0.1 M to 0.8 M in both single and double bath configurations. An insulated carbon grease sensor was mechanically stable while a composite Direct Assembly Process (DAP) sensor was fragile upon hydration. Scanning electron microscopy results from an impregnation-reduction technique showed gold nanoparticles were deposited most effectively when presoaked in a potassium hydroxide solution and on an uncoated membrane; surface resistances remained too high for sensor implementation. Through thickness carbon grease sensors showed a transient response to changes in concentration, and no meaningful concentration sensitivity was noted for the time scales over which EIS measurements were taken. Surface carbon grease electrodes attached to the polyamide thin film were not sensitive to concentration. The impedance spectra indicated the carbon grease sensor was unable to detect changes in concentration in double bath experiments when implemented with the polyamide surface exposed to salt solutions. DAP sensors lacked a consistent response to changes in concentration too. A reverse double bath experiment with the polysulfone layer exposed to a constant concentration exhibited a transient impedance response similar to through thickness carbon grease sensors in a single bath at constant concentration. These results suggest that the microporous polysulfone layer is responsible for sensor response to concentration.

Impact of different extraction methods on the quality of Dipteryx alata extracts

Directory of Open Access Journals (Sweden)

Frederico S. Martins

2013-05-01

Full Text Available This study aimed to impact of different extraction methods on the quality of Dipteryx alata Vogel, Fabaceae, extracts from fruits. The major compounds found were the lipids 38.9% (w/w and proteins 26.20% (w/w. The residual moisture was 7.20% (w/w, total fiber 14.50% (w/w, minerals 4.10% (w/w and carbohydrate 9.10 % (w/w. The species studied has great potential in producing oil, but the content and type of fatty acids obtained is dependent on the method of extraction. The Blingh & Dyer method was more selective for unsaturated fatty acids and Shoxlet method was more selective for saturated fatty acids. The tannin extraction by ultrasound (33.70 % w/w was 13.90% more efficient than extraction by decoction (29 % w/w.

Uranium extraction from phosphoric acid

International Nuclear Information System (INIS)

Araujo Figueiredo, C. de

1984-01-01

The recovery of uranium from phosphoric liquor by two extraction process is studied. First, uranium is reduced to tetravalent condition and is extracted by dioctypyrophosphoric acid. The re-extraction is made by concentrated phosphoric acid with an oxidizing agent. The re-extract is submitted to the second process and uranium is extracted by di-ethylhexilphosphoric acid and trioctylphosphine oxide. (M.A.C.) [pt

Extraction of plutonium(IV) by diglycolamide extractants in room temperature ionic liquids

Energy Technology Data Exchange (ETDEWEB)

Prabhu, Dattaprasad R.; Raut, Dhaval R.; Murali, Mallekav S.; Mohapatra, Prasanta K. [Bhabha Atomic Research Centre, Mumbai (India). Radiochemistry Div.

2017-06-01

Extraction of Pu(IV) was investigated using solutions of two diglycolamide extractants viz., N,N,N{sup '},N{sup '}-tetra-n-octyldiglycolamide (TODGA) and its branched homolog, N,N,N{sup '},N{sup '}-tetra(2-ethylhexyl) diglycolamide (T2EHDGA), dissolved in two imidazolium based room temperature ionic liquids viz., 1-butyl-3-methylimidazolium bis(trifluoromethanesulphonyl) imide ([C{sub 4}mim][NTf{sub 2}]) and 1-octyl-3-methylimidazolium bis(trifluoromethanesulphonyl) imide ([C{sub 8}mim][NTf{sub 2}]) from aqueous nitric acid medium. The extraction kinetics was found to be extremely slow which is reported for the first time for analogous extraction systems and took as long as 30 h to attain equilibrium D{sub Pu} values. In general, TODGA based solvents showed better extraction of Pu(IV) than the T2EHDGA based solvents, one order of magnitude higher, and though both the ionic liquids ultimately yielded comparable D{sub Pu} values, attainment of equilibrium was slower with [C{sub 4}mim][NTf{sub 2}]. The extracted species conformed to 1:1 for TODGA in both the ionic liquids while a mixture of 1:1 and 1:2 species was observed for T2EHDGA at 1 M HNO{sub 3} which changed to 1:1 species at 4 M HNO{sub 3}. The extracted species is proposed to be (Pu(L){sub x}{sup 4+}){sub IL} (where, L is the extractant and x=1 or 2) at lower acidities suggesting a cation exchange mechanism which changes over to (Pu(NO{sub 3}){sub 4} .L){sub IL} at 4 M HNO{sub 3} conforming to a solvation mechanism for all the systems except for T2EHDGA-[C{sub 8}mim][NTf{sub 2}]. UV-VIS spectroscopic studies were carried out to throw light on the nature of the extracted species.

Extraction of functional ingredients from spinach (Spinacia oleracea L.) using liquid solvent and supercritical CO₂ extraction.

Science.gov (United States)

Jaime, Laura; Vázquez, Erika; Fornari, Tiziana; López-Hazas, María del Carmen; García-Risco, Mónica R; Santoyo, Susana; Reglero, Guillermo

2015-03-15

In this work three different techniques were applied to extract dry leaves of spinach (Spinacia oleracea): solid-liquid extraction (SLE), pressurised liquid extraction (PLE) and supercritical fluid extraction (SFE) to investigate the influence of extraction solvent and technique on extracts composition and antioxidant activity. Moreover, the influence of carotenoids and phenolic compounds on the antioxidant and anti-inflammatory activities of spinach extracts was also studied. The higher concentrations of carotenoids and the lower content of phenolic compounds were observed in the supercritical CO₂ extracts; whereas water and/or ethanol PLE extracts presented low amounts of carotenoids and the higher concentrations of phenolic compounds. PLE extract with the highest content of phenolic compounds showed the highest antioxidant activity, although SFE carotenoid rich extract also showed a high antioxidant activity. Moreover, both extracts presented an important anti-inflammatory activity. PLE seems to be a good technique for the extraction of antioxidant and anti-inflammatory compounds from spinach leaves. Moreover, spinach phenolic compounds and carotenoids present a high antioxidant activity, whereas spinach carotenoids seem to show a higher anti-inflammatory activity than phenolic compounds. It is worth noting that of our knowledge this is the first time the anti-inflammatory activity of lipophilic extracts from spinach leaves is reported. © 2014 Society of Chemical Industry.

Tevatron extraction microcomputer

International Nuclear Information System (INIS)

Chapman, L.; Finley, D.A.; Harrison, M.; Merz, W.

1985-06-01

Extraction in the Fermilab Tevatron is controlled by a multi-processor Multibus microcomputer system called QXR (Quad eXtraction Regulator). QXR monitors several analog beam signals and controls three sets of power supplies: the ''bucker'' and ''pulse'' magnets at a rate of 5760 Hz, and the ''QXR'' magnets at 720 Hz. QXR supports multiple slow spills (up to a total of 35 seconds) with multiple fast pulses intermixed. It linearizes the slow spill and bucks out the high frequency components. Fast extraction is done by outputting a variable pulse waveform. Closed loop learning techniques are used to improve performance from cycle to cycle for both slow and fast extraction. The system is connected to the Tevatron clock system so that it can track the machine cycle. QXR is also connected to the rest of the Fermilab control system, ACNET. Through ACNET, human operators and central computers can monitor and control extraction through communications with QXR. The controls hardware and software both employ some standard and some specialized components. This paper gives an overview of QXR as a control system; another paper summarizes performance

Strategies for the extraction and analysis of non-extractable polyphenols from plants.

Science.gov (United States)

Domínguez-Rodríguez, Gloria; Marina, María Luisa; Plaza, Merichel

2017-09-08

The majority of studies based on phenolic compounds from plants are focused on the extractable fraction derived from an aqueous or aqueous-organic extraction. However, an important fraction of polyphenols is ignored due to the fact that they remain retained in the residue of extraction. They are the so-called non-extractable polyphenols (NEPs) which are high molecular weight polymeric polyphenols or individual low molecular weight phenolics associated to macromolecules. The scarce information available about NEPs shows that these compounds possess interesting biological activities. That is why the interest about the study of these compounds has been increasing in the last years. Furthermore, the extraction and characterization of NEPs are considered a challenge because the developed analytical methodologies present some limitations. Thus, the present literature review summarizes current knowledge of NEPs and the different methodologies for the extraction of these compounds, with a particular focus on hydrolysis treatments. Besides, this review provides information on the most recent developments in the purification, separation, identification and quantification of NEPs from plants. Copyright © 2017 Elsevier B.V. All rights reserved.

Improving extraction efficiency of the third integer resonant extraction using higher order multipoles

Energy Technology Data Exchange (ETDEWEB)

Brown, K. A. [Brookhaven National Lab. (BNL), Upton, NY (United States); Schoefer, V. [Brookhaven National Lab. (BNL), Upton, NY (United States); Tomizawa, M. [High Energy Accelerator Research Organization (KEK), Tsukuba (Japan)

2017-03-09

The new accelerator complex at J-PARC will operate with both high energy and very high intensity proton beams. With a design slow extraction efficiency of greater than 99% this facility will still be depositing significant beam power onto accelerator components [2]. To achieve even higher efficiencies requires some new ideas. The design of the extraction system and the accelerator lattice structure leaves little room for improvement using conventional techniques. In this report we will present one method for improving the slow extraction efficiency at J-PARC by adding duodecapoles or octupoles to the slow extraction system. We will review the theory of resonant extraction, describe simulation methods, and present the results of detailed simulations. From our investigations we find that we can improve extraction efficiency and thereby reduce the level of residual activation in the accelerator components and surrounding shielding.

Natural colorants: Pigment stability and extraction yield enhancement via utilization of appropriate pretreatment and extraction methods.

Science.gov (United States)

Ngamwonglumlert, Luxsika; Devahastin, Sakamon; Chiewchan, Naphaporn

2017-10-13

Natural colorants from plant-based materials have gained increasing popularity due to health consciousness of consumers. Among the many steps involved in the production of natural colorants, pigment extraction is one of the most important. Soxhlet extraction, maceration, and hydrodistillation are conventional methods that have been widely used in industry and laboratory for such a purpose. Recently, various non-conventional methods, such as supercritical fluid extraction, pressurized liquid extraction, microwave-assisted extraction, ultrasound-assisted extraction, pulsed-electric field extraction, and enzyme-assisted extraction have emerged as alternatives to conventional methods due to the advantages of the former in terms of smaller solvent consumption, shorter extraction time, and more environment-friendliness. Prior to the extraction step, pretreatment of plant materials to enhance the stability of natural pigments is another important step that must be carefully taken care of. In this paper, a comprehensive review of appropriate pretreatment and extraction methods for chlorophylls, carotenoids, betalains, and anthocyanins, which are major classes of plant pigments, is provided by using pigment stability and extraction yield as assessment criteria.

Laboratory robotics projects in the Analytical Development Division at the Savannah River Laboratory

International Nuclear Information System (INIS)

Lien, O.G.; Steele, A.W.

1986-01-01

To encourage the application of robotics technology for routine radiobench applications, a laboratory dedicated to the research and development of contained robotic systems is being constructed. The facility will have several robots located in laminar flow hoods, and the hoods are being designed to allow the possibility for multiple robots to work together. This paper presents both the design features of the hoods and the general layout of the laboratory, and also discusses an application of a robotic system for the routine nuclear counting of gamma tube samples. The gamma tube system is presently operating in one of the routine analysis laboratories. 5 figs

Modeling and prediction of extraction profile for microwave-assisted extraction based on absorbed microwave energy.

Science.gov (United States)

Chan, Chung-Hung; Yusoff, Rozita; Ngoh, Gek-Cheng

2013-09-01

A modeling technique based on absorbed microwave energy was proposed to model microwave-assisted extraction (MAE) of antioxidant compounds from cocoa (Theobroma cacao L.) leaves. By adapting suitable extraction model at the basis of microwave energy absorbed during extraction, the model can be developed to predict extraction profile of MAE at various microwave irradiation power (100-600 W) and solvent loading (100-300 ml). Verification with experimental data confirmed that the prediction was accurate in capturing the extraction profile of MAE (R-square value greater than 0.87). Besides, the predicted yields from the model showed good agreement with the experimental results with less than 10% deviation observed. Furthermore, suitable extraction times to ensure high extraction yield at various MAE conditions can be estimated based on absorbed microwave energy. The estimation is feasible as more than 85% of active compounds can be extracted when compared with the conventional extraction technique. Copyright © 2013 Elsevier Ltd. All rights reserved.

The Institute of Radiochemistry, University of Liege, (Sart-Tilman), Belgium

International Nuclear Information System (INIS)

Duyckaerts, G.

1977-01-01

The Institute of Radiochemistry, erected in the new Sart-Tilman campus of the University of Liege has been especially planned and equipped for research on actinide chemistry. The two-floor building is well adapted for work in glove-boxes and well ventilated hoods with highly radioactive α-emitters. For the last ten years, research has been carried out in the following directions: synthesis and structural analysis of actinide compounds, thermodynamic evaluations on actinide compounds by microcalorimetry, electrochemistry of actinides in fused salts, redox properties of actinides in fused salts by absorption spectrophotometry, solution chemistry of actinides by solvent extraction, ion exchange and electrochemistry. (T.G.)

Selective and Efficient Solvent Extraction of Copper(II Ions from Chloride Solutions by Oxime Extractants

Directory of Open Access Journals (Sweden)

Zahra Kaboli Tanha

2016-06-01

Full Text Available Oxime extractants 3-tert-butyl-2-hydroxy-5-methyl benzaldehyde oxime (HL1 and 3-tert-butyl-2-hydroxy-5-methoxy benzaldehyde oxime (HL2 were synthesized and characterized by conventional spectroscopic methods. Suitable lipophilic nature of the prepared extractants allowed examining the ability of these molecules for extraction-separation of copper from its mixture with normally associated metal ions by performing competitive extraction experiments of Cu(II, Co(II, Ni(II, Zn(II, Cd(II and Pb(II ions from chloride solutions. Both ligands transfer selectively the copper ions into dichloromethane by a cation exchange mechanism. Conventional log-log analysis and isotherm curves showed that Cu(II ions are extracted as the complexes with 1:2 metal to ligand ratio by both extractants. Verification of the effect of the organic diluent used in the extraction of copper ions by HL1 and HL2 demonstrated that the extraction efficiency varies as: dichloromethane ~ dichloroethane > toluene > xylene > ethylacetate. Time dependency investigation of the extraction processes revealed that the kinetics of the extraction of copper by HL2 is more rapid than that of HL1. The application of the ligands for extraction-separation of copper ions from leach solutions of cobalt and nickel-cadmium filter-cakes of a zinc production plants was evaluated.

Extraction Methods, Variability Encountered in

NARCIS (Netherlands)

Bodelier, P.L.E.; Nelson, K.E.

2014-01-01

Synonyms Bias in DNA extractions methods; Variation in DNA extraction methods Definition The variability in extraction methods is defined as differences in quality and quantity of DNA observed using various extraction protocols, leading to differences in outcome of microbial community composition

75 FR 22554 - Notice of Petitions by Firms for Determination of Eligibility To Apply for Trade Adjustment...

Science.gov (United States)

2010-04-29

... Specialty truck cabs, Joplin, MO 68801. hoods, etc.; construction and military cabs, hoods, etc.; Water... Company, Inc 1209 Logan Circle NW., 4/13/2010 The firm produces custom Atlanta, GA 30318. wood counter, table, and vanity tops. Primary material is wood. KMS Fab, LLC 100 Parry Street, Luzerne, 4/14/2010...

VULTURE NEWS 55.indd

African Journals Online (AJOL)

The Hooded Vulture Neophron monachus occurs naturally in most of Zambia's rural areas, especially around large cattle farms and human habitations. Being next to a large game farm, The Meintjes have a number of Hooded Vultures on their farm, Kamfinsa Dairy Farm. About seven years ago they slaughtered a sheep.

Antioxidant Properties of Crude Extract, Partition Extract, and Fermented Medium of Dendrobium sabin Flower

Directory of Open Access Journals (Sweden)

Farahziela Abu

2017-01-01

Full Text Available Antioxidant properties of crude extract, partition extract, and fermented medium from Dendrobium sabin (DS flower were investigated. The oven-dried DS flower was extracted using 100% methanol (w/v, 100% ethanol (w/v, and 100% water (w/v. The 100% methanolic crude extract showed the highest total phenolic content (40.33 ± mg GAE/g extract and the best antioxidant properties as shown by DPPH, ABTS, and FRAP assays. A correlation relationship between antioxidant activity and total phenolic content showed that phenolic compounds were the dominant antioxidant components in this flower extract. The microbial fermentation on DS flower medium showed a potential in increasing the phenolic content and DPPH scavenging activity. The TPC of final fermented medium showed approximately 18% increment, while the DPPH of fermented medium increased significantly to approximately 80% at the end of the fermentation. Dendrobium sabin (DS flower showed very good potential properties of antioxidant in crude extract and partition extract as well as better antioxidant activity in the flower fermented medium.

Supercritical fluid extraction of hops

Directory of Open Access Journals (Sweden)

ZORAN ZEKOVIC

2007-01-01

Full Text Available Five cultivars of hop were extracted by the method of supercritical fluid extraction using carbon dioxide (SFE–CO2 as extractant. The extraction (50 g of hop sample using a CO2 flow rate of 97.725 L/h was done in the two steps: 1. extraction at 150 bar and 40°C for 2.5 h (sample of series A was obtained and, after that, the same sample of hop was extracted in the second step: 2. extraction at 300 bar and 40 °C for 2.5 h (sample of series B was obtained. The Magnum cultivar was chosen for the investigation of the extraction kinetics. For the qualitative and quantitative analysis of the obtained hop extracts, the GC-MS method was used. Two of four themost common compounds of hop aroma (a-humulene and b-caryophyllene were detected in samples of series A. In addition, isomerized a-acids and a high content of b-acids were detected. The a-acids content in the samples of series B was the highest in the extract of the Magnum cultivar (it is a bitter variety of hop. The low contents of a-acids in all the other hop samples resulted in extracts with low a-acids content, i.e., that contents were under the prescribed a-acids content.

Effect of solvent type and ratio on betacyanins and antioxidant activity of extracts from Hylocereus polyrhizus flesh and peel by supercritical fluid extraction and solvent extraction.

Science.gov (United States)

Fathordoobady, Farahnaz; Mirhosseini, Hamed; Selamat, Jinap; Manap, Mohd Yazid Abd

2016-07-01

The main objective of the present study was to investigate the effect of solvent type and ratio as well as the extraction techniques (i.e. supercritical fluid extraction (SFE) and conventional solvent extraction) on betacyanins and antioxidant activity of the peel and fresh extract from the red pitaya (Hylocereus polyrhizus). The peel and flesh extracts obtained by SFE at 25MPa pressure and 10% EtOH/water (v/v) mixture as a co-solvent contained 24.58 and 91.27mg/100ml total betacyanin, respectively; while the most desirable solvent extraction process resulted in a relatively higher total betacyanin in the peel and flesh extracts (28.44 and 120.28mg/100ml, respectively). The major betacyanins identified in the pitaya peel and flesh extracts were betanin, isobetanin, phyllocactin, butyrylbetanin, isophyllocactin and iso-butyrylbetanin. The flesh extract had the stronger antioxidant activity than the peel extract when the higher proportion of ethanol to water (E/W) was applied for the extraction. Copyright © 2016 Elsevier Ltd. All rights reserved.

Synthesis and chemical modification of polymeric resins for the treatment of cations and aromatic hydrocarbons in produced oily water; Sintese de modificacao quimica de resina polimerica e aplicacao na remocao de cations e hidrocarbonetos aromaticos presentes em agua produzida

Energy Technology Data Exchange (ETDEWEB)

Aversa, Thiago M.; Rodrigues, Monique F.; Vieira, Helida V.P.; Queiros, Yure G.C.; Lucas, Elizabete F. [Universidade Federal do Rio de Janeiro, Instituto de Macromoleculas, Lab. de Macromoleculas e Coloides na Industria do Petroleo, Rio de Janeiro, RJ (Brazil)], e-mail: thiagoaversa@ima.ufrj.br

2011-07-01

The use of chemically modified resins in oily water treatment process is not very developed yet. Because of this, this work suggests to study the styrene and divinylbenzene sulfonation effect on oil and grease, aniline and calcium removal from the water. The aniline, oils and greases belong to a class of toxic organic compounds, with the Brazilian maximum limits established for disposal in CONAMA 393/2007, while the calcium ions belong to the group of cations of alkaline earth metals which improve hardness to the water, may cause fouling as carbonates and sulfates form. By using sulfonated resins in oily water treatment it is possible to remove not only oils and greases but also calcium and aniline. These kinds of polar compounds are removed because of the cation exchange capacity of resin. (author)

Diluent effects in solvent extraction. The Effects of Diluents in Solvent Extraction - a literature study

International Nuclear Information System (INIS)

Loefstroem-Engdahl, Elin; Aneheim, Emma; Ekberg, Christian; Foreman, Mark; Skarnemark, Gunnar

2010-01-01

The fact that the choice of organic diluent is important for a solvent extraction process goes without saying. Several factors, such as e.g. price, flash point, viscosity, polarity etc. each have their place in the planning of a solvent extraction system. This high number of variables makes the lack of compilations concerning diluent effects to an interesting topic. Often the interest for the research concerning a specific extraction system focuses on the extractant used and the complexes built up during an extraction. The diluents used are often classical ones, even if it has been shown that choice of diluent can affect extraction as well as separation in an extraction system. An attempt to point out important steps in the understanding of diluent effects in solvent extraction is here presented. This large field is, of course, not summarized in this article, but an attempt is made to present important steps in the understanding of diluents effects in solvent extraction. Trying to make the information concerning diluent effects and applications more easily accessible this review offers a selected summarizing of literature concerning diluents effects in solvent extraction. (authors)

Evaluation of Soxhlet extraction, accelerated solvent extraction and microwave-assisted extraction for the determination of polychlorinated biphenyls and polybrominated diphenyl ethers in soil and fish samples

International Nuclear Information System (INIS)

Wang Pu; Zhang Qinghua; Wang Yawei; Wang Thanh; Li Xiaomin; Ding Lei; Jiang Guibin

2010-01-01

Three commonly applied extraction techniques for persistent organic chemicals, Soxhlet extraction (SE), accelerated solvent extraction (ASE) and microwave-assisted extraction (MAE), were applied on soil and fish samples in order to evaluate their performances. For both PCBs and PBDEs, the two more recent developed techniques (ASE and MAE) were in general capable of producing comparable extraction results as the classical SE, and even higher extraction recoveries were obtained for some PCB congeners with large octanol-water partitioning coefficients (K ow ). This relatively uniform extraction results from ASE and MAE indicated that elevated temperature and pressure are favorable to the efficient extraction of PCBs from the solid matrices. For PBDEs, difference between the results from MAE and ASE (or SE) suggests that the MAE extraction condition needs to be carefully optimized according to the characteristics of the matrix and analyte to avoid degradation of higher brominated BDE congeners and improve the extraction yields.

Evaluation of Soxhlet extraction, accelerated solvent extraction and microwave-assisted extraction for the determination of polychlorinated biphenyls and polybrominated diphenyl ethers in soil and fish samples

Energy Technology Data Exchange (ETDEWEB)

Wang Pu [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, 18 Shuangqing Road, Beijing 100085 (China); Zhang Qinghua, E-mail: qhzhang@rcees.ac.cn [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, 18 Shuangqing Road, Beijing 100085 (China); Wang Yawei; Wang Thanh; Li Xiaomin; Ding Lei; Jiang Guibin [State Key Laboratory of Environmental Chemistry and Ecotoxicology, Research Center for Eco-Environmental Sciences, Chinese Academy of Sciences, 18 Shuangqing Road, Beijing 100085 (China)

2010-03-17

Three commonly applied extraction techniques for persistent organic chemicals, Soxhlet extraction (SE), accelerated solvent extraction (ASE) and microwave-assisted extraction (MAE), were applied on soil and fish samples in order to evaluate their performances. For both PCBs and PBDEs, the two more recent developed techniques (ASE and MAE) were in general capable of producing comparable extraction results as the classical SE, and even higher extraction recoveries were obtained for some PCB congeners with large octanol-water partitioning coefficients (K{sub ow}). This relatively uniform extraction results from ASE and MAE indicated that elevated temperature and pressure are favorable to the efficient extraction of PCBs from the solid matrices. For PBDEs, difference between the results from MAE and ASE (or SE) suggests that the MAE extraction condition needs to be carefully optimized according to the characteristics of the matrix and analyte to avoid degradation of higher brominated BDE congeners and improve the extraction yields.

Multimedia Information Extraction

CERN Document Server

Maybury, Mark T

2012-01-01

The advent of increasingly large consumer collections of audio (e.g., iTunes), imagery (e.g., Flickr), and video (e.g., YouTube) is driving a need not only for multimedia retrieval but also information extraction from and across media. Furthermore, industrial and government collections fuel requirements for stock media access, media preservation, broadcast news retrieval, identity management, and video surveillance.  While significant advances have been made in language processing for information extraction from unstructured multilingual text and extraction of objects from imagery and vid

Extraction of some acids using aliphatic amines; Extraction de quelques acides par des amines aliphatiques

Energy Technology Data Exchange (ETDEWEB)

Matutano, L [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1964-06-01

Hydrochloric, nitric, sulphuric, perchloric, phosphoric, acetic and formic acids in aqueous solution (0.05 to 10 M) are extracted by amberlite LA2 and trilaurylamine in solution, 5 per cent by volume, in kerosene and xylene respectively. The extraction process consists of: neutralization of the amine salt; a 'molecular extraction', i.e. an extraction using an excess of acid with respect to the stoichiometry of the amine salt. According to the behaviour of the acid during the extraction, three groups may be distinguished: completely dissociated acids, carboxylic acids, phosphoric acid. This classification is also valid for the extraction of the water which occurs simultaneously with that of the acid. An extraction mechanism is put forward for formic acid and the formation constant of its amine salt is calculated. (author) [French] Les acides chlorhydrique, nitrique, sulfurique, perchlorique, phosphorique, acetique et formique, en solution aqueuse - 0,05 a 10 M - sont extraits par l'amberlite LA2 et la trilaurylamine en solution, a 5 pour cent en volume, dans le kerosene et le xylene respectivement. L'extraction comprend: une neutralisation de l'amine par l'acide avec formation d'un sel d'amine; une 'extraction moleculaire', c'est-a-dire une extraction d'acide en exces par rapport a la stoechiometrie du sel d'amine. Suivant le comportement des acides au cours de l'extraction nous distinguons trois groupes: acides entierement dissocies, acides carboxyliques, acide phosphorique. Cette classification est egalement valable pour l'extraction de l'eau qui est simultanee a celle de l'acide. Un mecanisme d'extraction pour l'acide formique est propose et nous calculons la constante de formation de son sel d'amine. (auteur)

Optimization of microwave assisted extraction (MAE) and soxhlet extraction of phenolic compound from licorice root.

Science.gov (United States)

Karami, Zohreh; Emam-Djomeh, Zahra; Mirzaee, Habib Allah; Khomeiri, Morteza; Mahoonak, Alireza Sadeghi; Aydani, Emad

2015-06-01

In present study, response surface methodology was used to optimize extraction condition of phenolic compounds from licorice root by microwave application. Investigated factors were solvent (ethanol 80 %, methanol 80 % and water), liquid/solid ratio (10:1-25:1) and time (2-6 min). Experiments were designed according to the central composite rotatable design. The results showed that extraction conditions had significant effect on the extraction yield of phenolic compounds and antioxidant capacities. Optimal condition in microwave assisted method were ethanol 80 % as solvent, extraction time of 5-6 min and liquid/solid ratio of 12.7/1. Results were compared with those obtained by soxhlet extraction. In soxhlet extraction, Optimum conditions were extraction time of 6 h for ethanol 80 % as solvent. Value of phenolic compounds and extraction yield of licorice root in microwave assisted (MAE), and soxhlet were 47.47 mg/g and 16.38 %, 41.709 mg/g and 14.49 %, respectively. These results implied that MAE was more efficient extracting method than soxhlet.

Evaluation of urinary excretion of cortisol by radioimmunoassay through two methods (extracted and non-extracted)

International Nuclear Information System (INIS)

Fonte Kohek, M.B. da.

1992-01-01

The radioimmunoassay of urinary cortisol extracted by organic solvent (free cortisol) has been used for along time in the hypercortisolism diagnosis. With the development of more specific antisera it became possible to measure urinary cortisol without extracting it. The objective of this paper is to compare the feasibility, sensitivity and specificity of both methods (extracted versus non-extracted) in the hypercortisolism diagnosis. It was used Gamma Coat 125 I - cortisol kit provided by Clinical Assay, Incstar, US, for both methods extracting it with methylene chloride in order to measure the extracted cortisol. The sensitivity of the methods were similar (100% and 98,1%, for non-extracted and extracted methods, respectively). A positive correlation between the two methods was noticed in all groups studied (p < 0.05). It was concluded that both methods are efficient for the investigation of hypercortisolism. However, it's suggested that non-extracted urinary cortisol measurement should be the method of choice since it's an easy-to-perform and affordable method to diagnose Cushing's syndrome. (author)

[Study on condition for extraction of arctiin from fruits of Arctium lappa using supercritical fluid extraction].

Science.gov (United States)

Dong, Wen-hong; Liu, Ben

2006-08-01

To study the feasibility of supercritical fluid extraction (SFE) for arctiin from the fruits of Arctium lappa. The extracts were analyzed by HPLC, optimum extraction conditions were studied by orthogonal tests. The optimal extraction conditions were: pressure 40 MPa, temperature 70 degrees C, using methanol as modifier carrier at the rate of 0.55 mL x min(-1), static extraction time 5 min, dynamic extraction 30 min, flow rate of CO2 2 L x min(-1). SFE has the superiority of adjustable polarity, and has the ability of extracting arctiin.

Tevatron extraction microcomputer

International Nuclear Information System (INIS)

Chapman, L.; Finley, D.A.; Harrison, M.; Merz, W.; Batavia, IL)

1985-01-01

Extraction in the Fermilab Tevatron is controlled by a multi-processor Multibus microcomputer system called QXR (Quad eXtraction Regulator). QXR monitors several analog beam signals and controls three sets of power supplies: the ''bucker'' and ''pulse'' magnets at a rate of 5760 Hz, and the ''QXR'' magnets at 720 Hz. QXR supports multiple slow spills (up to a total of 35 seconds) with multiple fast pulses intermixed. It linearizes the slow spill and bucks out the high frequency components. Fast extraction is done by outputting a variable pulse waveform. Closed loop learning techniques are used to improve performance from cycle to cycle for both slow and fast extraction. The system is connected to the Tevatron clock system so that it can track the machine cycle. QXR is also connected to the rest of the Fermilab control system, ACNET. Through ACNET, human operators and central computers can monitor and control extraction through communications with QXR. The controls hardware and software both employ some standard and some specialized components. This paper gives an overview of QXR as a control system; another paper (1) summarizes performance

The diastal urethral stenosis in female children

International Nuclear Information System (INIS)

Pauer, W.

1985-01-01

The distal urethral stenosis in female children is a pathological reality. It is represented by the hymenal hood, the meatal stenosis and the distal urethral ring. Diagnosis and localisation of the stenosis is maintained by calibration with bougies a boule. Therapeutical consequences are: internal urethrotomy, bilateral meatotomy and excision of hymenal hoods. (Author)

Sulphur containing novel extractants for extraction-separation of palladium (II)

International Nuclear Information System (INIS)

Shukla, J.P.; Sawant, S.R.; Anil Kumar; Singh, R.K.

1995-01-01

Extraction performance of palladium (II) by sulphur containing extragents has unequivocally established their strong extraction ability toward this thiophilic soft metal. Hence a comprehensive investigative study was initiated by us to examine selective reversible extraction-separation of trace and macro amounts of palladium (II) from both aqueous nitric acid as well as hydrochloric acid media into 1,2-dichloroethane by 1,10-dithia-18 crown-6 (1,10-DT18C6), S 6 -pentano-36 (S 6 -P-36) and bis (2-ethylhexyl) sulphoxide (BESO) dissolved in toluene. From the study of aqueous phase acidity, reagent concentration, period of equilibration, diluent, strippant and diverse ions, conditions are established from its quantitative and reversible extraction. Recovery of Pd(II) from loaded thiacrown and sulphoxide phase is easily accomplished by using sodium thiocyanate, ammonium thiocyanate, thiourea, sodium thiosulphate and mixture of (2M Na 2 CO 3 + 0.5 NH 4 OH) (only for BESO) as the strippants. The lack of interference from even appreciable amounts of contaminants like 137 Cs, 106 Ru, 233 U and 239 Pu may be considered as one of the outstanding advantages of the method. Application of these extractants has been successfully tested for the recovery of palladium from high active waste matrix. The extracted complex from both the thiacrowns has been characterized by elemental analyses and UV-Visible spectra, confirmed to be PdA 2 .T (A = NO - 3 , Cl - ) from dilute (pH ∼ 2) acid solutions while composition of organic species with palladium for the sulphoxide, has also been confirmed to be disolvate of the type Pd(NO 3 ) 2 .2BESO. (author). 52 refs., 6 tabs., 6 figs

The organophosphorus extractants

International Nuclear Information System (INIS)

Zaoul, B.; Attou, M.; Azzouz, A.

1989-07-01

This work consists in a bibliographic review dealing with phosphorus and organophosphorus compounds chemistry and especially with the main extracting agents used in uranium ore treatment. In this context, a special interest is devoted to TBP, D 2 EHPA and TOPO. The content of this work is based on a large bibliography including cca. One hundred references related to many aspects concerning as well the nomenclature, the classification and the chemical structures of the organophosphorus compounds as synthesis methods, purification and analysis of the main extracting agents used in uranium extraction

Selective Liquid-Liquid Extraction of Lead Ions Using Newly Synthesized Extractant 2-(Dibutylcarbamoylbenzoic Acid

Directory of Open Access Journals (Sweden)

Hossein Soltani