Weapons-grade plutonium dispositioning. Volume 2: Comparison of plutonium disposition options

International Nuclear Information System (INIS)

Brownson, D.A.; Hanson, D.J.; Blackman, H.S.

1993-06-01

The Secretary of Energy requested the National Academy of Sciences (NAS) Committee on International Security and Arms Control to evaluate disposition options for weapons-grade plutonium. The Idaho National Engineering Laboratory (INEL) offered to assist the NAS in this evaluation by investigating the technical aspects of the disposition options and their capability for achieving plutonium annihilation levels greater than 90%. This report was prepared for the NAS to document the gathered information and results from the requested option evaluations. Evaluations were performed for 12 plutonium disposition options involving five reactor and one accelerator-based systems. Each option was evaluated in four technical areas: (1) fuel status, (2) reactor or accelerator-based system status, (3) waste-processing status, and (4) waste disposal status. Based on these evaluations, each concept was rated on its operational capability and time to deployment. A third rating category of option costs could not be performed because of the unavailability of adequate information from the concept sponsors. The four options achieving the highest rating, in alphabetical order, are the Advanced Light Water Reactor with plutonium-based ternary fuel, the Advanced Liquid Metal Reactor with plutonium-based fuel, the Advanced Liquid Metal Reactor with uranium-plutonium-based fuel, and the Modular High Temperature Gas-Cooled Reactor with plutonium-based fuel. Of these four options, the Advanced Light Water Reactor and the Modular High Temperature Gas-Cooled Reactor do not propose reprocessing of their irradiated fuel. Time constraints and lack of detailed information did not allow for any further ratings among these four options. The INEL recommends these four options be investigated further to determine the optimum reactor design for plutonium disposition

Weapons-grade plutonium dispositioning. Volume 2: Comparison of plutonium disposition options

Energy Technology Data Exchange (ETDEWEB)

Brownson, D.A.; Hanson, D.J.; Blackman, H.S. [and others

1993-06-01

The Secretary of Energy requested the National Academy of Sciences (NAS) Committee on International Security and Arms Control to evaluate disposition options for weapons-grade plutonium. The Idaho National Engineering Laboratory (INEL) offered to assist the NAS in this evaluation by investigating the technical aspects of the disposition options and their capability for achieving plutonium annihilation levels greater than 90%. This report was prepared for the NAS to document the gathered information and results from the requested option evaluations. Evaluations were performed for 12 plutonium disposition options involving five reactor and one accelerator-based systems. Each option was evaluated in four technical areas: (1) fuel status, (2) reactor or accelerator-based system status, (3) waste-processing status, and (4) waste disposal status. Based on these evaluations, each concept was rated on its operational capability and time to deployment. A third rating category of option costs could not be performed because of the unavailability of adequate information from the concept sponsors. The four options achieving the highest rating, in alphabetical order, are the Advanced Light Water Reactor with plutonium-based ternary fuel, the Advanced Liquid Metal Reactor with plutonium-based fuel, the Advanced Liquid Metal Reactor with uranium-plutonium-based fuel, and the Modular High Temperature Gas-Cooled Reactor with plutonium-based fuel. Of these four options, the Advanced Light Water Reactor and the Modular High Temperature Gas-Cooled Reactor do not propose reprocessing of their irradiated fuel. Time constraints and lack of detailed information did not allow for any further ratings among these four options. The INEL recommends these four options be investigated further to determine the optimum reactor design for plutonium disposition.

CANDU physics considerations for the disposition of weapons-grade plutonium

Energy Technology Data Exchange (ETDEWEB)

Pitre, J; Chan, P; Dastur, A [Atomic Energy of Canada Ltd., Mississauga, ON (Canada)

1996-12-31

At the request of the US Department of Energy AECL has examined the feasibility of using CANDU for the disposition of weapons grade plutonium. Utilizing existing CANDU technology, the feasibility of using MOX (mixed oxide) fuel in an existing CANDU reactor was studied. The results of this study indicate that the target disposition for disposal of weapons grade plutonium can be met without the requirement of any major modifications to existing plant design. (author). 3 refs., 4 tabs., 5 figs.

CANDU physics considerations for the disposition of weapons-grade plutonium

International Nuclear Information System (INIS)

Pitre, J.; Chan, P.; Dastur, A.

1995-01-01

At the request of the US Department of Energy AECL has examined the feasibility of using CANDU for the disposition of weapons grade plutonium. Utilizing existing CANDU technology, the feasibility of using MOX (mixed oxide) fuel in an existing CANDU reactor was studied. The results of this study indicate that the target disposition for disposal of weapons grade plutonium can be met without the requirement of any major modifications to existing plant design. (author). 3 refs., 4 tabs., 5 figs

Two convenient low-temperature routes to single crystals of plutonium dioxide

Energy Technology Data Exchange (ETDEWEB)

Meredith, Nathan A. [Departments of Chemistry and Biochemistry, University of Notre Dame, Notre Dame, IN 46556 (United States); Wang, Shuao; Diwu, Juan [School of Radiation Medicine and Protection and School of Radiological and Interdisciplinary Sciences, Soochow University, Suzhou, Jiangsu 215123 (China); Albrecht-Schmitt, Thomas E., E-mail: talbrechtschmitt@gmail.com [Department of Chemistry and Biochemistry, Florida State University, Tallahassee, FL 32306 (United States)

2014-11-15

Highlights: • Two low-temperature routes to the growth single crystals of plutonium dioxide. • Safer methods of preparing PuO{sub 2} single crystals that do not involve solid-state synthetic techniques. • Solvothermal crystal growth of plutonium dioxide. - Abstract: During the solvothermal synthesis of a low-dimensional borate, KB{sub 5}O{sub 7}(OH){sub 2}⋅2H{sub 2}O, in the presence of Pu(III), single crystals of plutonium dioxide unexpectedly formed. Single crystals of PuO{sub 2} also formed during the hydrothermal synthesis of another borate, Na{sub 2}B{sub 5}O{sub 8}(OH)⋅2H{sub 2}O, in the presence of Pu(III). The reactions were conducted at 170 °C and 150 °C, respectively, which are much lower temperature than previously reported preparations of crystalline PuO{sub 2}. Yellow–green crystals with a tablet habit were characterized by single crystal X-ray diffraction and solid-state UV–vis–NIR absorption spectroscopy. The crystal structure was solved by direct methods with R{sub 1} = 1.26% for 19 unique observed reflections. PuO{sub 2} is cubic, space group Fm3{sup ‾}m, and adopts the fluorite structure type. The lattice parameter was determined to be a = 5.421(5) Å giving a volume of 159.3(2) Å{sup 3}. The absorption spectrum is consistent with Pu(IV)

Standard test method for plutonium assay by plutonium (III) diode array spectrophotometry

CERN Document Server

American Society for Testing and Materials. Philadelphia

2002-01-01

1.1 This test method describes the determination of total plutonium as plutonium(III) in nitrate and chloride solutions. The technique is applicable to solutions of plutonium dioxide powders and pellets (Test Methods C 697), nuclear grade mixed oxides (Test Methods C 698), plutonium metal (Test Methods C 758), and plutonium nitrate solutions (Test Methods C 759). Solid samples are dissolved using the appropriate dissolution techniques described in Practice C 1168. The use of this technique for other plutonium-bearing materials has been reported (1-5), but final determination of applicability must be made by the user. The applicable concentration range for plutonium sample solutions is 10–200 g Pu/L. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropria...

Primary pulmonary sarcoma in a rhesus monkey after inhalation of plutonium dioxide

International Nuclear Information System (INIS)

Hahn, F.F.; Brooks, A.L.; Mewhinney, J.A.

1987-01-01

A pulmonary fibrosarcoma of bronchial origin was discovered in a Rhesus monkey that died of pulmonary fibrosis 9 years after inhalation of plutonium-239 dioxide and with a radiation dose to lung of 1400 rad (14 Gy). It grew around the major bronchus of the right cardiac lung lobe and extended into the bronchial lumen and into surrounding pulmonary parenchyma. It also readily invaded muscular pulmonary arteries, resulting in infarction and scarring in the right cardiac lobe. Despite this aggressive growth, the tumor did not metastasize. The primary cause of death was severe pulmonary fibrosis involving the alveolar septa and and perivascular and peribronchial interstitium. Bullous or pericitrical emphysema was prominent. The initial lung burden of plutonium in this monkey was 270 nCi (10 kBq) which is equivalent to approximately 500 times the maximum permissible lung burden for man on a radioactivity per unit body weight basis. The time-dose relationship for survival is consistent with that of dogs and baboons that inhaled plutonium dioxide and died with lung tumors

Weapons-grade plutonium dispositioning. Volume 3: A new reactor concept without uranium or thorium for burning weapons-grade plutonium

International Nuclear Information System (INIS)

Ryskamp, J.M.; Schnitzler, B.G.; Fletcher, C.D.

1993-06-01

The National Academy of Sciences (NAS) requested that the Idaho National Engineering Laboratory (INEL) examine concepts that focus only on the destruction of 50,000 kg of weapons-grade plutonium. A concept has been developed by the INEL for a low-temperature, low-pressure, low-power density, low-coolant-flow-rate light water reactor that destroys plutonium quickly without using uranium or thorium. This concept is very safe and could be designed, constructed, and operated in a reasonable time frame. This concept does not produce electricity. Not considering other missions frees the design from the paradigms and constraints used by proponents of other dispositioning concepts. The plutonium destruction design goal is most easily achievable with a large, moderate power reactor that operates at a significantly lower thermal power density than is appropriate for reactors with multiple design goals. This volume presents the assumptions and requirements, a reactor concept overview, and a list of recommendations. The appendices contain detailed discussions on plutonium dispositioning, self-protection, fuel types, neutronics, thermal hydraulics, off-site radiation releases, and economics

Reactions of plutonium dioxide with water and oxygen-hydrogen mixtures: Mechanisms for corrosion of uranium and plutonium

Energy Technology Data Exchange (ETDEWEB)

Haschke, John M.; Allen, Thomas H.; Morales, Luis A.

1999-06-18

Investigation of the interactions of plutonium dioxide with water vapor and with an oxygen-hydrogen mixture show that the oxide is both chemically reactive and catalytically active. Correspondence of the chemical behavior with that for oxidation of uranium in moist air suggests that similar catalytic processes participate in the mechanism of moisture-enhanced corrosion of uranium and plutonium. Evaluation of chemical and kinetic data for corrosion of the metals leads to a comprehensive mechanism for corrosion in dry air, water vapor, and moist air. Results are applied in confirming that the corrosion rate of Pu in water vapor decreases sharply between 100 and 200 degrees C.

Fluorine and chlorine determination in mixed uranium-plutonium oxide fuel and plutonium dioxide

International Nuclear Information System (INIS)

Elinson, S.V.; Zemlyanukhina, N.A.; Pavlova, I.V.; Filatkina, V.P.; Tsvetkova, V.T.

1981-01-01

A technique of fluorine and chlorine determination in the mixed uranium-plutonium oxide fuel and plutonium dioxide, based on their simultaneous separation by means of pyrohydrolysis, is developed. Subsequently, fluorine is determined by photometry with alizarincomplexonate of lanthanum or according to the weakening of zirconium colouring with zylenol orange. Chlorine is determined using the photonephelometric method according to the reaction of chloride-ion interaction with silver nitrate or by spectrophotometric method according to the reaction with mercury rhodanide. The lower limit of fluorine determination is -6x10 -5 %, of chlorine- 1x10 -4 % in the sample of 1g. The relative mean quadratic deviation of the determination result (Ssub(r)), depends on the character of the material analyzed and at the content of nx10 -4 - nx10 -3 mass % is equal to from 0.05 to 0.32 for fluorine and from 0.11 to 0.35 for chlorine [ru

Studies on O/M ratio determination in uranium oxide, plutonium oxide and uranium-plutonium mixed oxide

International Nuclear Information System (INIS)

Sampath, S.; Chawla, K.L.

1975-01-01

Thermogravimetric studies were carried out in unsintered and sintered samples of uranium oxide, plutonium oxide and uranium-plutonium mixed oxide under different atmospheric conditions (air, argon and moist argon/hydrogen). Moisture loss was found to occur below 200 0 C for uranium dioxide samples, upto 700 0 C for sintered plutonium dioxide and negligible for sintered samples. The O/M ratios for non-stoichiometric uranium dioxide (sintered and unsintered), plutonium dioxide and mixed uranium and plutonium oxides (sintered) could be obtained with a precision of +- 0.002. Two reference states UOsub(2.000) and UOsub(2.656) were obtained for uranium dioxide and the reference state MOsub(2.000) was used for other cases. For unsintered plutonium dioxide samples, accurate O/M ratios could not be obtained of overlap of moisture loss with oxygen loss/gain. (author)

Disposition of weapons-grade plutonium in Westinghouse reactors

International Nuclear Information System (INIS)

Alsaed, A.A.; Adams, M.

1998-03-01

The authors have studied the feasibility of using weapons-grade plutonium in the form of mixed-oxide (MOX) fuel in existing Westinghouse reactors. They have designed three transition Cycles from an all LEU core to a partial MOX core. They found that four-loop Westinghouse reactors such as the Vogtle power plant are capable of handling up to 45 percent weapons-grade MOX loading without any modifications. The authors have also designed two kinds of weapons-grade MOX assemblies with three enrichments per assembly and four total enrichments. Wet annular burnable absorber (WABA) rods were used in all the MOX feed assemblies, some burned MOX assemblies, and some LEU feed assemblies. Integral fuel burnable absorber (IFBA) was used in the rest of the LEU feed assemblies. The average discharge burnup of MOX assemblies was over 47,000 MWD/MTM, which is more than enough to meet the open-quotes spent fuel standard.close quotes One unit is capable of consuming 0.462 MT of weapons-grade plutonium per year. Preliminary analyses showed that important reactor physics parameters for the three transitions cycles are comparable to those of LEU cores including boron levels, reactivity coefficients, peaking factors, and shutdown margins. Further transient analyses will need to be performed

Weapons grade plutonium disposition in PWR, CANDU and FR

International Nuclear Information System (INIS)

Deplech, M.; Tommasi, J.; Zaetta, A.

2000-01-01

In the frame work of the AIDA/MOX phase I/I/ program (1994-1997) between France and Russia, the disposition of plutonium in reactors was studied. The LWR (Light Water Reactor), FR (Fast reactors), CANDU (Heavy Water Reactors), HTR (High Temperature Reactors) options for using excess dismantled weapons plutonium for peaceful commercial nuclear power generating purposes offer some advantages over the remaining options (storage). The AIDA/MOX phase 1 program covers different topics, among which are the neutronic aspects of loading reactors with weapons-grade plutonium. The conclusions are that the weapon plutonium consumption is similar in the different type of reactors. However, the use of inert matrices allows to increase the mass balance for a same denaturing level. The use of Thorium as a matrix or special isotopes to increase the proliferation resistance prove to be insufficient. (author)

The export of weapons grade plutonium to the USA

International Nuclear Information System (INIS)

Kollerstrom, N.

1986-01-01

Reprocessed spent Magnox fuel from British nuclear power plants has led, it is claimed, to the production of plutonium, some of weapons grade. Some of this has been exported to the USA where, it is assumed, it is used for military purposes. The route and agreements which make this possible and the quantities involved are reported. Inspection by IAEA is insufficient to check the Central Electricity Generating Board's (CEGB) claim that no CEGB plutonium has been used for a military purpose. The CEGB case, presented at the Sizewell Inquiry is discussed. In the United States it is not clear whether plutonium from Britain, at present in a civil stockpile, will be transferred to military use or not. (U.K.)

Risk of transporting plutonium dioxide and liquid plutonium nitrate by truck and rail

International Nuclear Information System (INIS)

Williams, L.D.; Hall, R.J.

1976-01-01

This paper presents an analysis method developed to assess the risk in the transportation of radioactive materials and demonstrates its application by summarizing the results of risk assessments of the shipment of plutonium dioxide powder and liquid plutonium nitrate by truck and rail in the United States. In the risk assessment, postulated release modes (series of events that could result in a release of radioactive material) are identified using the fault tree analysis method. Two categories of events that could contribute to a release during transportation are considered: accidents and substandard packaging conditions. The likelihood of basic events in these categories are determined from general accident experience, radioactive material shipping experience, engineering analysis, etc. Using the laws of combining probabilities, the likelihood of radioactive material release is then evaluated. Since accidents vary greatly in severity, the releases from these postulated events also vary in magnitude from the no release condition up through release of the entire package contents. The bases for the release quantities assigned to the postulated accidents sequences are discussed. The consequences of these postulated releases are evaluated based on the amount of plutonium estimated to be released to the environs, the probable weather conditions at the time of the accident, and population density downwind from the accident scene. The likelihood and consequence of postulated releases are coupled and expressed as a risk spectra. (author)

Standard test method for plutonium by Iron (II)/Chromium (VI) amperometric titration

CERN Document Server

American Society for Testing and Materials. Philadelphia

2002-01-01

1.1 This test method covers the determination of plutonium in unirradiated nuclear-grade plutonium dioxide, uranium-plutonium mixed oxides with uranium (U)/plutonium (Pu) ratios up to 21, plutonium metal, and plutonium nitrate solutions. Optimum quantities of plutonium to measure are 7 to 15 mg. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

A method for the gravimetric determination of plutonium in pure plutonium nitrate concentrate solution

International Nuclear Information System (INIS)

Mair, M.A.; Savage, D.J.

1986-12-01

Plutonium nitrate solution is treated with sulphuric acid before being heated and finally ignited. The stoichiometric plutonium dioxide so formed is weighed and hence the plutonium content is calculated. (author)

Determination of plutonium in pure plutonium nitrate solutions - Gravimetric method

International Nuclear Information System (INIS)

1987-01-01

This International Standard specifies a precise and accurate gravimetric method for determining the concentration of plutonium in pure plutonium nitrate solutions and reference solutions, containing between 100 and 300 g of plutonium per litre, in a nitric acid medium. The weighed portion of the plutonium nitrate is treated with sulfuric acid and evaporated to dryness. The plutonium sulfate is decomposed and formed to oxide by heating in air. The oxide is ignited in air at 1200 to 1250 deg. C and weighed as stoichiometric plutonium dioxide, which is stable and non-hygroscopic

A Study of the Stability and Characterization Plutonium Dioxide and Chemical Characterization [of] Rocky Flats and Los Alamos Plutonium-Containing Incinerator Ash

International Nuclear Information System (INIS)

Ray, A.K.; Boettger, J.C.; Behrens, Robert G.

1999-01-01

In the presentation ''A Study of the Stability and Characterization of Plutonium Dioxide'', the authors discuss their recent work on actinide stabilities and characterization, in particular, plutonium dioxide PuO 2 . Earlier studies have indicated that PuO 2 has the fluorite structure of CaF 2 and typical oxide semiconductor properties. However, detailed results on the bulk electronic structure of this important actinide oxide have not been available. The authors have used all-electron, full potential linear combinations Gaussian type orbitals fitting function (LCGTO-FF) method to study PuO 2 . The LCGTO-FF technique characterized by its use of three independent GTO basis sets to expand the orbitals, charge density, and exchange-correlation integral kernels. Results will be presented on zero pressure using both the Hedin-Lundquist local density approximation (LDA) model or the Perdew-Wang generalized gradient approximation (GGA) model. Possibilities of different characterizations of PuO 2 will be explored. The paper ''Chemical Characterization Rocky Flats and Los Alamos Plutonium-Containing Incinerator Ash'' describes the results of a comprehensive study of the chemical characteristics of virgin, calcined and fluorinated incinerator ash produced at the Rocky Flats Plant and at the Los Alamos National Laboratory prior to 1988. The Rocky Flats and Los Alamos virgin, calcined, and fluorinated ashes were also dissolved using standard nitrate dissolution chemistry. Corresponding chemical evaluations were preformed on the resultant ash heel and the results compared with those of the virgin ash. Fluorination studies using FT spectroscopy as a diagnostic tool were also performed to evaluate the chemistry of phosphorus, sulfur, carbon, and silicon containing species in the ash. The distribution of plutonium and other chemical elements with the virgin ash, ash heel, fluorinated ash, and fluorinated ash heel particulates were studied in detail using microprobe analysis. Some

A review of plutonium oxalate decomposition reactions and effects of decomposition temperature on the surface area of the plutonium dioxide product

International Nuclear Information System (INIS)

Orr, R.M.; Sims, H.E.; Taylor, R.J.

2015-01-01

Plutonium (IV) and (III) ions in nitric acid solution readily form insoluble precipitates with oxalic acid. The plutonium oxalates are then easily thermally decomposed to form plutonium dioxide powder. This simple process forms the basis of current industrial conversion or ‘finishing’ processes that are used in commercial scale reprocessing plants. It is also widely used in analytical or laboratory scale operations and for waste residues treatment. However, the mechanisms of the thermal decompositions in both air and inert atmospheres have been the subject of various studies over several decades. The nature of intermediate phases is of fundamental interest whilst understanding the evolution of gases at different temperatures is relevant to process control. The thermal decomposition is also used to control a number of powder properties of the PuO_2 product that are important to either long term storage or mixed oxide fuel manufacturing. These properties are the surface area, residual carbon impurities and adsorbed volatile species whereas the morphology and particle size distribution are functions of the precipitation process. Available data and experience regarding the thermal and radiation-induced decompositions of plutonium oxalate to oxide are reviewed. The mechanisms of the thermal decompositions are considered with a particular focus on the likely redox chemistry involved. Also, whilst it is well known that the surface area is dependent on calcination temperature, there is a wide variation in the published data and so new correlations have been derived. Better understanding of plutonium (III) and (IV) oxalate decompositions will assist the development of more proliferation resistant actinide co-conversion processes that are needed for advanced reprocessing in future closed nuclear fuel cycles. - Highlights: • Critical review of plutonium oxalate decomposition reactions. • New analysis of relationship between SSA and calcination temperature. • New SEM

Weapons-grade plutonium dispositioning. Volume 4

International Nuclear Information System (INIS)

Sterbentz, J.W.; Olsen, C.S.; Sinha, U.P.

1993-06-01

This study is in response to a request by the Reactor Panel Subcommittee of the National Academy of Sciences (NAS) Committee on International Security and Arms Control (CISAC) to evaluate the feasibility of using plutonium fuels (without uranium) for disposal in existing conventional or advanced light water reactor (LWR) designs and in low temperature/pressure LWR designs that might be developed for plutonium disposal. Three plutonium-based fuel forms (oxides, aluminum metallics, and carbides) are evaluated for neutronic performance, fabrication technology, and material and compatibility issues. For the carbides, only the fabrication technologies are addressed. Viable plutonium oxide fuels for conventional or advanced LWRs include plutonium-zirconium-calcium oxide (PuO 2 -ZrO 2 -CaO) with the addition of thorium oxide (ThO 2 ) or a burnable poison such as erbium oxide (Er 2 O 3 ) or europium oxide (Eu 2 O 3 ) to achieve acceptable neutronic performance. Thorium will breed fissile uranium that may be unacceptable from a proliferation standpoint. Fabrication of uranium and mixed uranium-plutonium oxide fuels is well established; however, fabrication of plutonium-based oxide fuels will require further development. Viable aluminum-plutonium metallic fuels for a low temperature/pressure LWR include plutonium aluminide in an aluminum matrix (PuAl 4 -Al) with the addition of a burnable poison such as erbium (Er) or europium (Eu). Fabrication of low-enriched plutonium in aluminum-plutonium metallic fuel rods was initially established 30 years ago and will require development to recapture and adapt the technology to meet current environmental and safety regulations. Fabrication of high-enriched uranium plate fuel by the picture-frame process is a well established process, but the use of plutonium would require the process to be upgraded in the United States to conform with current regulations and minimize the waste streams

Plutonium oxides and uranium and plutonium mixed oxides. Carbon determination

International Nuclear Information System (INIS)

Anon.

Determination of carbon in plutonium oxides and uranium plutonium mixed oxides, suitable for a carbon content between 20 to 3000 ppm. The sample is roasted in oxygen at 1200 0 C, the carbon dioxide produced by combustion is neutralized by barium hydroxide generated automatically by coulometry [fr

Plutonium-238 and plutonium-239 metabolism in dairy cows following ingestion of mixed oxides

International Nuclear Information System (INIS)

Patzer, R.G.; Mullen, A.A.; Sutton, W.W.; Potter, G.D.; Mosley, R.E.; Efurd, D.W.; Stalnaker, N.D.

1985-01-01

Dairy cows were given oral dosage of plutonium-238 and plutonium-239 dioxide particles in a study to determine the relative gastrointestinal absorption and tissue distribution of the nuclides. Two cows were given particles in which the two isotopes were homogeneously mixed within the particles. A third cow was given two batches of particles which contained either plutonium-238 or plutonium-239. Results indicate that, when the two isotopes of plutonium are homogeneous within the particles, there is no difference between plutonium-238 and plutonium-239 in the relative gastrointestinal absorption and tissue distribution

CANDU reactors with reactor grade plutonium/thorium carbide fuel

Energy Technology Data Exchange (ETDEWEB)

Sahin, Suemer [Atilim Univ., Ankara (Turkey). Faculty of Engineering; Khan, Mohammed Javed; Ahmed, Rizwan [Pakistan Institute of Engineering and Applied Sciences, Islamabad (Pakistan); Gazi Univ., Ankara (Turkey). Faculty of Technology

2011-08-15

Reactor grade (RG) plutonium, accumulated as nuclear waste of commercial reactors can be re-utilized in CANDU reactors. TRISO type fuel can withstand very high fuel burn ups. On the other hand, carbide fuel would have higher neutronic and thermal performance than oxide fuel. In the present work, RG-PuC/ThC TRISO fuels particles are imbedded body-centered cubic (BCC) in a graphite matrix with a volume fraction of 60%. The fuel compacts conform to the dimensions of sintered CANDU fuel compacts are inserted in 37 zircolay rods to build the fuel zone of a bundle. Investigations have been conducted on a conventional CANDU reactor based on GENTILLYII design with 380 fuel bundles in the core. Three mixed fuel composition have been selected for numerical calculation; (1) 10% RG-PuC + 90% ThC; (2) 30% RG-PuC + 70% ThC; (3) 50% RG-PuC + 50% ThC. Initial reactor criticality values for the modes (1), (2) and (3) are calculated as k{sub {infinity}}{sub ,0} = 1.4848, 1.5756 and 1.627, respectively. Corresponding operation lifetimes are {proportional_to} 2.7, 8.4, and 15 years and with burn ups of {proportional_to} 72 000, 222 000 and 366 000 MW.d/tonne, respectively. Higher initial plutonium charge leads to higher burn ups and longer operation periods. In the course of reactor operation, most of the plutonium will be incinerated. At the end of life, remnants of plutonium isotopes would survive; and few amounts of uranium, americium and curium isotopes would be produced. (orig.)

A review of plutonium oxalate decomposition reactions and effects of decomposition temperature on the surface area of the plutonium dioxide product

Energy Technology Data Exchange (ETDEWEB)

Orr, R.M.; Sims, H.E.; Taylor, R.J., E-mail: robin.j.taylor@nnl.co.uk

2015-10-15

Plutonium (IV) and (III) ions in nitric acid solution readily form insoluble precipitates with oxalic acid. The plutonium oxalates are then easily thermally decomposed to form plutonium dioxide powder. This simple process forms the basis of current industrial conversion or ‘finishing’ processes that are used in commercial scale reprocessing plants. It is also widely used in analytical or laboratory scale operations and for waste residues treatment. However, the mechanisms of the thermal decompositions in both air and inert atmospheres have been the subject of various studies over several decades. The nature of intermediate phases is of fundamental interest whilst understanding the evolution of gases at different temperatures is relevant to process control. The thermal decomposition is also used to control a number of powder properties of the PuO{sub 2} product that are important to either long term storage or mixed oxide fuel manufacturing. These properties are the surface area, residual carbon impurities and adsorbed volatile species whereas the morphology and particle size distribution are functions of the precipitation process. Available data and experience regarding the thermal and radiation-induced decompositions of plutonium oxalate to oxide are reviewed. The mechanisms of the thermal decompositions are considered with a particular focus on the likely redox chemistry involved. Also, whilst it is well known that the surface area is dependent on calcination temperature, there is a wide variation in the published data and so new correlations have been derived. Better understanding of plutonium (III) and (IV) oxalate decompositions will assist the development of more proliferation resistant actinide co-conversion processes that are needed for advanced reprocessing in future closed nuclear fuel cycles. - Highlights: • Critical review of plutonium oxalate decomposition reactions. • New analysis of relationship between SSA and calcination temperature. �

A review of plutonium oxalate decomposition reactions and effects of decomposition temperature on the surface area of the plutonium dioxide product

Science.gov (United States)

Orr, R. M.; Sims, H. E.; Taylor, R. J.

2015-10-01

Plutonium (IV) and (III) ions in nitric acid solution readily form insoluble precipitates with oxalic acid. The plutonium oxalates are then easily thermally decomposed to form plutonium dioxide powder. This simple process forms the basis of current industrial conversion or 'finishing' processes that are used in commercial scale reprocessing plants. It is also widely used in analytical or laboratory scale operations and for waste residues treatment. However, the mechanisms of the thermal decompositions in both air and inert atmospheres have been the subject of various studies over several decades. The nature of intermediate phases is of fundamental interest whilst understanding the evolution of gases at different temperatures is relevant to process control. The thermal decomposition is also used to control a number of powder properties of the PuO2 product that are important to either long term storage or mixed oxide fuel manufacturing. These properties are the surface area, residual carbon impurities and adsorbed volatile species whereas the morphology and particle size distribution are functions of the precipitation process. Available data and experience regarding the thermal and radiation-induced decompositions of plutonium oxalate to oxide are reviewed. The mechanisms of the thermal decompositions are considered with a particular focus on the likely redox chemistry involved. Also, whilst it is well known that the surface area is dependent on calcination temperature, there is a wide variation in the published data and so new correlations have been derived. Better understanding of plutonium (III) and (IV) oxalate decompositions will assist the development of more proliferation resistant actinide co-conversion processes that are needed for advanced reprocessing in future closed nuclear fuel cycles.

Accountability methods for plutonium and uranium: the NRC manuals

Energy Technology Data Exchange (ETDEWEB)

Gutmacher, R.G.; Stephens, F.B.

1977-09-28

Four manuals containing methods for the accountability of plutonium nitrate solutions, plutonium dioxide, uranium dioxide and mixed uranium-plutonium oxide have been prepared by us and issued by the U.S. Nuclear Regulatory Commission. A similar manual on methods for the accountability of uranium and plutonium in reprocessing plant dissolver solutions is now in preparation. In the present paper, we discuss the contents of the previously issued manuals and give a preview of the manual now being prepared.

Accountability methods for plutonium and uranium: the NRC manuals

International Nuclear Information System (INIS)

Gutmacher, R.G.; Stephens, F.B.

1977-01-01

Four manuals containing methods for the accountability of plutonium nitrate solutions, plutonium dioxide, uranium dioxide and mixed uranium-plutonium oxide have been prepared by us and issued by the U.S. Nuclear Regulatory Commission. A similar manual on methods for the accountability of uranium and plutonium in reprocessing plant dissolver solutions is now in preparation. In the present paper, we discuss the contents of the previously issued manuals and give a preview of the manual now being prepared

Assessment and reduction of proliferation risk of reactor-grade plutonium regarding construction of ‘fizzle bombs’ by terrorists

International Nuclear Information System (INIS)

Serfontein, Dawid E.; Mulder, Eben J.; Reitsma, Frederik

2014-01-01

The approximately 23.7 wt% 240 Pu in reactor-grade plutonium denatures the 239 Pu to the extent that it cannot fuel high yield nuclear weapons. 240 Pu has a high spontaneous fission rate, which increases the spontaneous neutron flux within the fuel. When such a nuclear weapon is triggered, these neutrons cause the nuclear fission chain reaction to pre-detonate which blows the imploding fuel shell apart before the designed level of compression and reactivity could be attained, thereby greatly reducing the average energy yield of such “fizzle” bombs. Therefore reactor-grade plutonium is normally viewed as highly proliferation resistant. In this article the literature on the proliferation resistance of reactor-grade plutonium and on the mechanism and effect of fizzle bombs is reviewed in order to test this view. It is shown that even very low yield fizzle bombs, exploded in urban areas, would still cause serious blast damage as well as radioactive contamination. Combined with the high levels of induced terror, fizzle bombs might thus be attractive psychological weapons for terrorists. Therefore reactor-grade plutonium may not be sufficiently proliferation resistant against nuclear terrorism. However, denaturisation with more than 9% 238 Pu produces high levels of decay heat which will melt or explode the high explosives around uncooled implosion type weapons, rendering them useless. Unfortunately, reactor-grade Pu contains only 2.7% 238 Pu and is thus not sufficiently proliferation resistant in this respect. It is also shown that the associated neptunium poses a substantial proliferation risk. In the present study strong improvement of the proliferation resistance was demonstrated by simulation of incineration of reactor-grade plutonium in the 400 MW th Pebble Bed Modular Reactor Demonstration Power Plant. Results for modified fuel cycles, aimed at transmutating 237 Np to 238 Pu are also reported. However, these modifications increased the disloaded heavy metal

The disposition of weapon grade plutonium: costs and tradeoffs

International Nuclear Information System (INIS)

Weida, W.J.

1996-01-01

This paper explores some of the economic issues surrounding a major area of expenditures now facing the nuclear powers: the disposition of weapon-grade plutonium either through 'burning' in nuclear reactors for power generation or by other means. Under the current budgeting philosophy in the United States, programs managed by the Department of Energy (DOE) tend to compete with one another for the total funds assigned to that agency. For example, in the FY1995 DOE budget a tradeoff was made between increased funding for nuclear weapons and reduced funding for site cleanup. No matter which disposition alternative is chosen, if disposition funds are controlled by the DOE in the US or by a government agency in any other country, disposition is likely to compete directly or indirectly with other alternatives for energy funding. And if they are subsidized by any government, research into plutonium as reactor fuel or the operations associated with such use are likely to consume funds that might otherwise be available to support sustainable energy alternatives. When all costs are considered, final waste disposal costs will be incurred whatever disposal option is taken. These costs could potentially be offset by doing something profitable with the plutonium prior to final storage, but this paper has shown that finding a profitable use for plutonium is unlikely. Thus, the more probable case is one where the costs of basic waste storage are increased by whatever costs are associated with the disposition option chosen. The factors most likely to significantly increase costs appear to arise from four areas: (1) The level of subsidization in the 'profitable' parts of the disposition program. (2) Those items (such as reprocessing) that increase the volume of waste and thus, the cost of waste disposal. (3) The cost of security and its direct relationship to the number of times plutonium is handled or moved. (4) The cost of research and development of new and unproven methods of

Investigation of plutonium (4) hydroxoformates

International Nuclear Information System (INIS)

Andryushin, V.G.; Belov, V.A.; Galaktionov, S.V.; Kozhevnikov, P.B.; Matyukha, V.A.; Shmidt, V.S.

1982-01-01

Deposition processes of plutonium (4) hydroxoformates in the system Pu(NO 3 ) 4 -HNO 3 -HCoOH-N6 4 OH-H 2 O have been studied in pH range 0.2-10.7 at total plutonium concentration in the system 100 g/l. It is shown that under the conditions plutonium (4) hydrolysis takes place with the formation of hydroxoformates. A local maximum of plutonium (4) hydroxoformate solubility in the range pH=3.8-4.8, which is evidently conditioned by the formation of soluble formate complex of plutonium in the region, is pointed out. The basic plutonium (4) formates of the composition PuOsub(x)(OH)sub(y)(COOH)sub(4-2x-y)xnHsub(2)O, where 1,3 >=x >= 0.7, 1.7 >= y >= 1.0 and n=1.5-7.0, are singled out, their thermal stability being studied. Density of the crystals and plutonium dioxide, formed during their thermal decomposition, is measured. It is established that for plutonium (4) hydroxoformates common regularities of the influence of salt composition (OH - -, CHOO - - and H 2 O-group numbers in the mulecule) on position of temperature decomposition effects and on the density of compounds, which have been previously found during the study of thorium and plutonium hydroxosalts are observed. It is shown that the density of plutonium dioxide decreases with the increase of hydration and hydrolysis degree of the initial plutonium hydroxoformate

Surplus plutonium disposition draft environmental impact statement. Summary

International Nuclear Information System (INIS)

1998-07-01

On May 22, 1997, DOE published a Notice of Intent (NOI) in the Federal Register (62 Federal Register 28009) announcing its decision to prepare an environmental impact statement (EIS) that would tier from the analysis and decisions reached in connection with the Storage and Disposition of Weapons-Usable Fissile Materials Final Programmatic EIS (Storage and Disposition PEIS). DOE's disposition strategy allows for both the immobilization of surplus plutonium and its use as mixed oxide (MOX) fuel in existing domestic, commercial reactors. The disposition of surplus plutonium would also involve disposal of the immobilized plutonium and MOX fuel (as spent nuclear fuel) in a geologic repository. The Surplus Plutonium Disposition Environmental Impact Statement analyzes alternatives that would use the immobilization approach (for some of the surplus plutonium) and the MOX fuel approach (for some of the surplus plutonium); alternatives that would immobilize all of the surplus plutonium; and the No Action Alternative. The alternatives include three disposition facilities that would be designed so that they could collectively accomplish disposition of up to 50 metric tons (55 tons) of surplus plutonium over their operating lives: (1) the pit disassembly and conversion facility would disassemble pits (a weapons component) and convert the recovered plutonium, as well as plutonium metal from other sources, into plutonium dioxide suitable for disposition; (2) the immobilization facility would include a collocated capability for converting nonpit plutonium materials into plutonium dioxide suitable for immobilization and would be located at either Hanford or SRS. DOE has identified SRS as the preferred site for an immobilization facility; (3) the MOX fuel fabrication facility would fabricate plutonium dioxide into MOX fuel

METHOD OF PRODUCING PLUTONIUM TETRAFLUORIDE

Science.gov (United States)

Tolley, W.B.; Smith, R.C.

1959-12-15

A process is presented for preparing plutonium tetrafluoride from plutonium(IV) oxalate. The oxalate is dried and decomposed at about 300 deg C to the dioxide, mixed with ammonium bifluoride, and the mixture is heated to between 50 and 150 deg C whereby ammonium plutonium fluoride is formed. The ammonium plutonium fluoride is then heated to about 300 deg C for volatilization of ammonium fluoride. Both heating steps are preferably carried out in an inert atmosphere.

The effect of plutonium dioxide water surface coverage on the generation of hydrogen and oxygen

Energy Technology Data Exchange (ETDEWEB)

Veirs, Douglas K. [Los Alamos National Laboratory; Berg, John M. [Los Alamos National Laboratory; Crowder, Mark L. [Savannah River National Laboratory

2012-06-20

The conditions for the production of oxygen during radiolysis of water adsorbed onto plutonium dioxide powder are discussed. Studies in the literature investigating the radiolysis of water show that both oxygen and hydrogen can be generated from water adsorbed on high-purity plutonium dioxide powder. These studies indicate that there is a threshold in the amount of water below which oxygen is not generated. The threshold is associated with the number of monolayers of adsorbed water and is shown to occur at approximately two monolayers of molecularly adsorbed water. Material in equilibrium with 50% relative humidity (RH) will be at the threshold for oxygen generation. Using two monolayers of molecularly adsorbed water as the threshold for oxygen production, the total pressure under various conditions is calculated assuming stoichiometric production of hydrogen and oxygen. The specific surface area of the oxide has a strong effect on the final partial pressure. The specific surface areas resulting in the highest pressures within a 3013 container are evaluated. The potential for oxygen generation is mitigated by reduced relative humidity, and hence moisture adsorption, at the oxide surface which occurs if the oxide is warmer than the ambient air. The potential for oxygen generation approaches zero as the temperature difference between the ambient air and the material approaches 6 C.

Assessment and reduction of proliferation risk of reactor-grade plutonium regarding construction of ‘fizzle bombs’ by terrorists

Energy Technology Data Exchange (ETDEWEB)

Serfontein, Dawid E., E-mail: Dawid.Serfontein@nwu.ac.za [School for Mechanical and Nuclear Engineering, North West University (PUK-Campus), PRIVATE BAG X6001 (Internal Post Box 360), Potchefstroom 2520 (South Africa); Mulder, Eben J. [School for Mechanical and Nuclear Engineering, North West University (South Africa); Reitsma, Frederik [Calvera Consultants (South Africa)

2014-05-01

The approximately 23.7 wt% {sup 240}Pu in reactor-grade plutonium denatures the {sup 239}Pu to the extent that it cannot fuel high yield nuclear weapons. {sup 240}Pu has a high spontaneous fission rate, which increases the spontaneous neutron flux within the fuel. When such a nuclear weapon is triggered, these neutrons cause the nuclear fission chain reaction to pre-detonate which blows the imploding fuel shell apart before the designed level of compression and reactivity could be attained, thereby greatly reducing the average energy yield of such “fizzle” bombs. Therefore reactor-grade plutonium is normally viewed as highly proliferation resistant. In this article the literature on the proliferation resistance of reactor-grade plutonium and on the mechanism and effect of fizzle bombs is reviewed in order to test this view. It is shown that even very low yield fizzle bombs, exploded in urban areas, would still cause serious blast damage as well as radioactive contamination. Combined with the high levels of induced terror, fizzle bombs might thus be attractive psychological weapons for terrorists. Therefore reactor-grade plutonium may not be sufficiently proliferation resistant against nuclear terrorism. However, denaturisation with more than 9% {sup 238}Pu produces high levels of decay heat which will melt or explode the high explosives around uncooled implosion type weapons, rendering them useless. Unfortunately, reactor-grade Pu contains only 2.7% {sup 238}Pu and is thus not sufficiently proliferation resistant in this respect. It is also shown that the associated neptunium poses a substantial proliferation risk. In the present study strong improvement of the proliferation resistance was demonstrated by simulation of incineration of reactor-grade plutonium in the 400 MW{sub th} Pebble Bed Modular Reactor Demonstration Power Plant. Results for modified fuel cycles, aimed at transmutating {sup 237}Np to {sup 238}Pu are also reported. However, these

Method and apparatus for producing food grade carbon dioxide

International Nuclear Information System (INIS)

Nobles, J.E.; Swenson, L.K.

1984-01-01

A method is disclosed of producing food grade carbon dioxide from an impure carbon dioxide source stream containing contaminants which may include light and heavy hydrocarbons (at least C 1 to C 3 ) and light sulfur compounds such as hydrogen sulfide and carbonyl sulfide as well as heavier sulfur constituents in the nature of mercaptans (RSH) and/or organic mono and disulfides (RSR and RSSR). Nitrogen, water and/or oxygen may also be present in varying amounts in the impure feed stream. The feed gas is first rectified with liquid carbon dioxide condensed from a part of the feed stream to remove heavy hydrocarbons and heavy sulfur compounds, then passed through an absorber to effect removal of the light sulfur compounds, next subjected to an oxidizing atmosphere capable of converting all of the C 2 hydrocarbons and optionally a part of the methane to carbon oxides and water, chilled to condense the water in the remaining gas stream without formation of hydrates, liquefied for ease of handling and storage and finally stripped to remove residual contaminants such as methane, carbon monoxide and nitrogen to produce the final food grade carbon dioxide product

Materials measurement and accounting in an operating plutonium conversion and purification process. Phase I. Process modeling and simulation

International Nuclear Information System (INIS)

Thomas, C.C. Jr.; Ostenak, C.A.; Gutmacher, R.G.; Dayem, H.A.; Kern, E.A.

1981-04-01

A model of an operating conversion and purification process for the production of reactor-grade plutonium dioxide was developed as the first component in the design and evaluation of a nuclear materials measurement and accountability system. The model accurately simulates process operation and can be used to identify process problems and to predict the effect of process modifications

An oxyde mixture fuel containing uranium and plutonium dioxides and process to obtain this oxyde mixture

International Nuclear Information System (INIS)

Hannerz, K.

1976-01-01

An oxide-mixture fuel containing uranium and plutonium dioxides having the slage of spherical, or nearly spherical, oxide-mixture particles with a diameter within the range of from 0.2 to 2 mn charactarized in that each oxide-mixture particles is provided with an outer layer comprising mainly UO2, the thickness of which is at least 0.05; whereas the inner portion of the oxide-mixture particles comprises mainly PUO 2

A new concept of fast reactors, the potentialities of burning in them of actinoid and weapon-grade plutonium

International Nuclear Information System (INIS)

Murogov, V.M.; Troyanov, M.F.; Ilyunin, V.G.; Rudneva, V.Ya.

1992-01-01

The approach to a possible solution of the problem of peaceful utilization of weapon-grade plutonium released in the result of nuclear disarmament in Russia is given in the repot. As the most safe, ecologically acceptable and economically effective way of the plutonium utilization is the usage of such plutonium as a fuel for atomic power station. It is proposed to decide the problem on the basis of BN-600 and BN-800 reactors. In the approach, thorium could be used as a fertile material. The secondary nuclear fuel U-233 is expedient to use in light-water reactors of new generation. (author)

Surplus plutonium disposition draft environmental impact statement. Volume 2

International Nuclear Information System (INIS)

1998-07-01

On May 22, 1997, DOE published a Notice of Intent (NOI) in the Federal Register (62 Federal Register 28009) announcing its decision to prepare an environmental impact statement (EIS) that would tier from the analysis and decisions reached in connection with the Storage and Disposition of Weapons-Usable Fissile Materials Final Programmatic EIS (Storage and Disposition PEIS). DOE's disposition strategy allows for both the immobilization of surplus plutonium and its use as mixed oxide (MOX) fuel in existing domestic, commercial reactors. The disposition of surplus plutonium would also involve disposal of the immobilized plutonium and MOX fuel (as spent nuclear fuel) in a geologic repository. The Surplus Plutonium Disposition Environmental Impact Statement analyzes alternatives that would use the immobilization approach (for some of the surplus plutonium) and the MOX fuel approach (for some of the surplus plutonium); alternatives that would immobilize all of the surplus plutonium; and the No Action Alternative. The alternatives include three disposition facilities that would be designed so that they could collectively accomplish disposition of up to 50 metric tons (55 tons) of surplus plutonium over their operating lives: (1) the pit disassembly and conversion facility would disassemble pits (a weapons component) and convert the recovered plutonium, as well as plutonium metal from other sources, into plutonium dioxide suitable for disposition; (2) the immobilization facility would include a collocated capability for converting nonpit plutonium materials into plutonium dioxide suitable for immobilization and would be located at either Hanford or SRS. DOE has identified SRS as the preferred site for an immobilization facility; (3) the MOX fuel fabrication facility would fabricate plutonium dioxide into MOX fuel. Volume 2 contains the appendices to the report and describe the following: Federal Register notices; contractor nondisclosure statement; adjunct melter

Surplus plutonium disposition draft environmental impact statement. Volume 1, Part A

International Nuclear Information System (INIS)

1998-07-01

On May 22, 1997, DOE published a Notice of Intent (NOI) in the Federal Register (62 Federal Register 28009) announcing its decision to prepare an environmental impact statement (EIS) that would tier from the analysis and decisions reached in connection with the Storage and Disposition of Weapons-Usable Fissile Materials Final Programmatic EIS (Storage and Disposition PEIS). DOE's disposition strategy allows for both the immobilization of surplus plutonium and its use as mixed oxide (MOX) fuel in existing domestic, commercial reactors. The disposition of surplus plutonium would also involve disposal of the immobilized plutonium and MOX fuel (as spent nuclear fuel) in a geologic repository. The Surplus Plutonium Disposition Environmental Impact Statement analyzes alternatives that would use the immobilization approach (for some of the surplus plutonium) and the MOX fuel approach (for some of the surplus plutonium); alternatives that would immobilize all of the surplus plutonium; and the No Action Alternative. The alternatives include three disposition facilities that would be designed so that they could collectively accomplish disposition of up to 50 metric tons (55 tons) of surplus plutonium over their operating lives: (1) the pit disassembly and conversion facility would disassemble pits (a weapons component) and convert the recovered plutonium, as well as plutonium metal from other sources, into plutonium dioxide suitable for disposition; (2) the immobilization facility would include a collocated capability for converting nonpit plutonium materials into plutonium dioxide suitable for immobilization and would be located at either Hanford or SRS. DOE has identified SRS as the preferred site for an immobilization facility; (3) the MOX fuel fabrication facility would fabricate plutonium dioxide into MOX fuel. This volume includes background information; purpose of and need for the proposed action; alternatives for disposition of surplus weapons useable plutonium; and

Surplus plutonium disposition draft environmental impact statement. Volume 1, Part B

International Nuclear Information System (INIS)

1998-07-01

On May 22, 1997, DOE published a Notice of Intent (NOI) in the Federal Register (62 Federal Register 28009) announcing its decision to prepare an environmental impact statement (EIS) that would tier from the analysis and decisions reached in connection with the Storage and Disposition of Weapons-Usable Fissile Materials Final Programmatic EIS (Storage and Disposition PEIS). DOE's disposition strategy allows for both the immobilization of surplus plutonium and its use as mixed oxide (MOX) fuel in existing domestic, commercial reactors. The disposition of surplus plutonium would also involve disposal of the immobilized plutonium and MOX fuel (as spent nuclear fuel) in a geologic repository. The Surplus Plutonium Disposition Environmental Impact Statement analyzes alternatives that would use the immobilization approach (for some of the surplus plutonium) and the MOX fuel approach (for some of the surplus plutonium); alternatives that would immobilize all of the surplus plutonium; and the No Action Alternative. The alternatives include three disposition facilities that would be designed so that they could collectively accomplish disposition of up to 50 metric tons (55 tons) of surplus plutonium over their operating lives: (1) the pit disassembly and conversion facility would disassemble pits (a weapons component) and convert the recovered plutonium, as well as plutonium metal from other sources, into plutonium dioxide suitable for disposition; (2) the immobilization facility would include a collocated capability for converting nonpit plutonium materials into plutonium dioxide suitable for immobilization and would be located at either Hanford or SRS. DOE has identified SRS as the preferred site for an immobilization facility; (3) the MOX fuel fabrication facility would fabricate plutonium dioxide into MOX fuel. This volume has chapters on environmental consequences; environmental regulations, permits, and consultations; a glossary; list of preparers; distribution list

Utilization of Cs137 to generate a radiation barrier for weapons grade plutonium immobilized in borosilicate glass canisters. Revision 1

International Nuclear Information System (INIS)

Jardine, L.J.; Armantrout, G.A.; Collins, L.F.

1995-01-01

One of the ways recommended by a recent National Academy of Sciences study to dispose of excess weapons-grade plutonium is to encapsulate the plutonium in a glass in combination with high-level radioactive wastes (HLW) to generate an intense radiation dose rate field. The objective is to render the plutonium as difficult to access as the plutonium contained in existing US commercial spent light-water reactor (LWR) fuel until it can be disposed of in a permanent geological repository. A radiation dose rate from a sealed canister of 1,000 rem/h (10 Sv/h) at 1 meter for at least 30 years after fabrication was assumed in this paper to be a radiation dose comparable to spent LWR fuel. This can be achieved by encapsulating the plutonium in a borosilicate glass with an adequate amount of a single fission product in the HLWS, namely radioactive Cs 137 . One hundred thousand curies of Cs 137 will generate a dose rate of 1,000 rem/h (10 Sv/h) at 1 meter for at least 30 years when imbedded into canisters of the size proposed for the Savannah River Site's vitrified high-level wastes. The United States has a current inventory of 54 MCi of CS 137 that has been separated from defense HLWs and is in sealed capsules. This single curie inventory is sufficient to spike 50 metric tons of excess weapons-grade plutonium if plutonium can be loaded at 5.5 wt% in glass, or 540 canisters. Additional CS 137 inventories exist in the United States' HLWs from past reprocessing operations, should additional curies be required. Using only one fission product, CS 137 , rather than the multiple chemical elements and compounds in HLWs to generate a high radiation dose rate from a glass canister greatly simplifies the processing engineering retirement for encapsulating plutonium in a borosilicate glass

Cooperative Studies in the Utilization and Storage of Excess Weapons-Grade Plutonium

Energy Technology Data Exchange (ETDEWEB)

Bolyatko, V. V. [Moscow Engineering Physics Institute (Russia)

1998-01-29

This technical report is a tangible and verifiable deliverable associated with the Nuclear Group subproject “Cooperative Studies in the Utilization and Storage of Excess Weapons-grade Plutonium.” This report is an assessment ofthe work performed by the Russian party from 1 October 1995 through 30 September 1996 regarding milestones defined in the contract between the Moscow Engineering Physics Institute (MEPhI) and the Texas Engineering Experiment Station (TEES). In these interactions, TEES serves as agent of the Amarillo National Resource Center for Plutonium (ANRCP) in the capacity oflead institution for the Nuclear Group of the ANRCP. The official Statement ofWork dated 8 April 1996 enumerates specific milestones and deliverables. In its present form, this report is an edited version ofthe translation submitted to TEES by MEPhI on 7 October 1996. The principal investigators for this subproject are Dr. Paul Nelson of TEES and Dr. Victor Bolyatko of the Moscow Engineering Physics Institute.

Standard test methods for chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium nitrate solutions

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 These test methods cover procedures for the chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium nitrate solutions to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Plutonium by Controlled-Potential Coulometry Plutonium by Amperometric Titration with Iron(II) Plutonium by Diode Array Spectrophotometry Free Acid by Titration in an Oxalate Solution 8 to 15 Free Acid by Iodate Precipitation-Potentiometric Titration Test Method 16 to 22 Uranium by Arsenazo I Spectrophotometric Test Method 23 to 33 Thorium by Thorin Spectrophotometric Test Method 34 to 42 Iron by 1,10-Phenanthroline Spectrophotometric Test Method 43 to 50 Impurities by ICP-AES Chloride by Thiocyanate Spectrophotometric Test Method 51 to 58 Fluoride by Distillation-Spectrophotometric Test Method 59 to 66 Sulfate by Barium Sulfate Turbidimetric Test Method 67 to 74 Isotopic Composition by Mass Spectrom...

Neutronic design of a plutonium-thorium burner small nuclear reactor

International Nuclear Information System (INIS)

Hartanto, Donny

2010-02-01

A small nuclear reactor using thorium and plutonium fuel has been designed from the neutronic point of view. The thermal power of the reactor is 150 MWth and it is proposed to be used to supply electricity in an island in Indonesia. Thorium and plutonium fuel was chosen because in recent years the thorium fuel cycle is one of the promising ways to deal with the increasing number of plutonium stockpiles, either from the utilization of uranium fuel cycle or from nuclear weapon dismantling. A mixed fuel of thorium and plutonium will not generate the second generation of plutonium which will be a better way to incinerate the excess plutonium compared with the MOX fuel. Three kinds of plutonium grades which are the reactor grade (RG), weapon grade (WG), and spent fuel grade (SFG) plutonium, were evaluated as the thorium fuel mixture in the 17x17 Westinghouse PWR Fuel assembly. The evaluated parameters were the multiplication factor, plutonium depletion, fissile buildup, neutron spectrum, and temperature reactivity feedback. An optimization was also done to increase the plutonium depletion by changing the Moderator to Fuel Ratio (MFR). The computer codes TRITON (coupled NEWT and ORIGEN-S) in SCALE version 6 were used as the calculation tool for this assembly level. From the evaluation and optimization of the fuel assembly, the whole core was designed. The core was consisted of 2 types of thorium fuel with different plutonium grade and it followed the checkerboard loading pattern. A new concept of enriched burnable poison was also introduced to the core. The core life is 6.4 EFPY or 75 GWd/MTHM. It can burn up to 58% of its total mass of initial plutonium. VENTURE was used as the calculation tool for the core level

PRISM reactor. An option for plutonium disposition?

Energy Technology Data Exchange (ETDEWEB)

Fehlinger, Sebastian; Friess, Friederike; Kuett, Moritz [IANUS, Technische Universitaet Darmstadt (Germany)

2015-07-01

The Power Reactor Innovative Small Module (PRISM) is sodium cooled fast reactor model. The energy output depends on the core configuration, however with an energy output of approximately 300 MWe, the PRISM reactor belongs to the class of small modular reactors. Beside using the reactor as a breeder reactor or for the transmutation of nuclear waste, it might also be used as a burner reactor for separated plutonium. This includes for example U.S.-American excess weapon-grade plutonium as well as separated reactor-grade plutonium. Recently, there has been an ongoing discussion in GB to use the PRISM reactor to dispose their excess civilian plutonium. Depending on the task, the core configuration varies slightly. We will present different layouts and the matching MCNP models, these models can then be used to conduct depletion calculations. From these results, analysis of the change in the plutonium isotopics in the spent fuel, the amount of fissioned plutonium, and the possible annual plutonium throughputs is possible.

An Opportunity to Immobilize 1.6 MT or More of Weapons-Grade Plutonium at the Mayak and Krasnoyarsk-26 Sites

International Nuclear Information System (INIS)

Jardine, L J; Borisov, G B; Rovny, S I; Kudinov, K G; Shvedov, A A

2001-01-01

The Mayak Production Association (PA Mayak), an industrial site in Russia, will be assigned multiple new plutonium disposition missions in order to implement the ''Agreement Between The Government Of The United States Of America And The Government Of Russian Federation Concerning The Management And Disposition Of Plutonium Designated As No Longer Required For Defense Purposes And Related Cooperation'' signed September 1, 2000, by Gore and Kasyanov, In addition, the mission of industrial-scale mixed-oxide (MOX) fabrication will be assigned to either the Mining Chemical Combine (MCC) industrial site at Krasnoyarsk-26 (K-26) or PA Mayak. Over the next decades, these new missions will generate radioactive wastes containing weapons-grade plutonium. The existing Mayak and K-26 onsite facilities and infrastructures cannot currently treat and immobilize these Pu-containing wastes for storage and disposal. However, the wastes generated under the Agreement must be properly immobilized, treated, and managed. New waste treatment and immobilization missions at Mayak may include operating facilities for plutonium metal-to-oxide conversion processes, industrial-scale MOX fuel fabrication, BN-600 PAKET hybrid core MOX fuel fabrication, and a plutonium conversion demonstration process. The MCC K-26 site, if assigned the industrial-scale MOX fuel fabrication mission, would also need to add facilities to treat and immobilize the Pu-containing wastes. This paper explores the approach and cost of treatment and immobilization facilities at both Mayak and K-26. The current work to date at Mayak and MCC K-26 indicates that the direct immobilization of 1.6 MT of weapons-grade plutonium is a viable and cost-effective alternative

Plutonium Finishing Plant (PFP) Safety Class and Safety Significant Commercial Grade Items (CGI) Critical Characteristic

International Nuclear Information System (INIS)

THOMAS, R.J.

2000-01-01

This document specifies the critical characteristics for Commercial Grade Items (CGI) procured for use in the Plutonium Finishing Plant as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to properly perform its safety function. There may be several manufacturers or models that meet the critical characteristics of any one item

Standard test methods for chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade uranium dioxide powders and pellets

CERN Document Server

American Society for Testing and Materials. Philadelphia

1999-01-01

1.1 These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade uranium dioxide powders and pellets to determine compliance with specifications. 1.2 This test method covers the determination of uranium and the oxygen to uranium atomic ratio in nuclear-grade uranium dioxide powder and pellets. 1.4 This test method covers the determination of chlorine and fluorine in nuclear-grade uranium dioxide. With a 1 to 10-g sample, concentrations of 5 to 200 g/g of chlorine and 1 to 200 μg/g of fluorine are determined without interference. 1.5 This test method covers the determination of moisture in uranium dioxide samples. Detection limits are as low as 10 μg. 1.6 This test method covers the determination of nitride nitrogen in uranium dioxide in the range from 10 to 250 μg. 1.7 This test method covers the spectrographic analysis of nuclear-grade UO2 for the 26 elements in the ranges indicated in Table 2. 1.8 For simultaneous determination of trace ele...

PLUTONIUM FINISHING PLANT (PFP) SUB-GRADE EE/CA EVALUATION OF ALTERNATIVES: A NEW MODEL

International Nuclear Information System (INIS)

HOPKINS, A.M.

2007-01-01

An engineering evaluation/cost analysis (EE/CA) was performed at the Hanford Site's Plutonium Finishing Plant (PFP). The purpose of the EVCA was to identify the sub-grade items to be evaluated; determine the Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA) hazardous substances through process history and available data; evaluate these hazards; and as necessary, identify the available alternatives to reduce the risk associated with the contaminants. The sub-grade EWCA considered four alternatives for an interim removal action: (1) No Action; (2) Surveillance and Maintenance (S and M); (3) Stabilize and Leave in Place (Stabilization); and (4) Remove, Treat and Dispose (RTD). Each alternative was evaluated against the CERCLA criteria for effectiveness, implementability, and cost

Multi-generational stewardship of plutonium

International Nuclear Information System (INIS)

Pillay, K.K.S.

1997-01-01

The post-cold war era has greatly enhanced the interest in the long-term stewardship of plutonium. The management of excess plutonium from proposed nuclear weapons dismantlement has been the subject of numerous intellectual discussions during the past several years. In this context, issues relevant to long-term management of all plutonium as a valuable energy resource are also being examined. While there are differing views about the future role of plutonium in the economy, there is a recognition of the environmental and health related problems and proliferation potentials of weapons-grade plutonium. The long-term management of plutonium as an energy resource will require a new strategy to maintain stewardship for many generations to come

A kinetic study of plutonium dioxide dissolution in hydrochloric acid using iron (II) as an electron transfer catalyst

International Nuclear Information System (INIS)

Fife, K.W.

1996-09-01

Effective dissolution of plutonium dioxide has traditionally been accomplished by contact with strong nitric acid containing a small amount of fluoride at temperatures of ∼ 100 C. In spite of these aggressive conditions, PuO 2 dissolution is sometimes incomplete requiring additional contact with the solvent. This work focused on an alternative to conventional dissolution in nitric acid where an electron transfer catalyst, Fe(II), was used in hydrochloric acid. Cyclic voltammetry was employed as an in-situ analytical technique for monitoring the dissolution reaction rate. The plutonium oxide selected for this study was decomposed plutonium oxalate with > 95% of the material having a particle diameter (< 70 microm) as determined by a scanning laser microscopy technique. Attempts to dry sieve the oxide into narrow size fractions prior to dissolution in the HCl-Fe(II) solvent system failed, apparently due to significant interparticle attractive forces. Although sieve splits were obtained, subsequent scanning laser microscopy analysis of the sieve fractions indicated that particle segregation was not accomplished and the individual sieve fractions retained a particle size distribution very similar to the original powder assemblage. This phenomena was confirmed through subsequent dissolution experiments on the various screen fractions which illustrated no difference in kinetic behavior between the original oxide assemblage and the sieve fractions

An assessment of the use of diluents in the vitrification of weapons-grade plutonium

International Nuclear Information System (INIS)

Sylvester, K.W.B.; Simonson, S.A.

1996-01-01

A technical analysis was performed to determine the feasibility and utility of vitrifying weapons-grade plutonium (WGPu) with various diluents. The diluents considered were reactor-grade plutonium (RGPu) and several rare earths. The use of these diluents could affect both the useability of the material for weapons and long-term environmental safety. Blending RGPu with WGPu would increase the compressed critical mass of the WGPu mixture only slightly; but the blending would increase pre-detonation probabilities. Blends with the rare earths (notably Eu) would be highly effective in increasing the compressed critical mass. In addition to their effectiveness in increasing critical mass, the rare earths were investigated as criticality controllers due to their neutron absorption capabilities and insolubility in aqueous environments. Thorium (assumed as a Pu surrogate) and the rare earths Eu, Gd, and Sm were added to two standard frits (ARM-1 and SRL-165) and melted into glass. Aqueous leach tests were performed to measure rare earth leaching and determine the added elements' effects on glass durability. Europium was much more leach resistant than boron in the glasses tested. The added elements had no negative effect on the environmental durability of the glasses tested at 90 degrees C. No fission product releases were detected in the ARM-1 compositions (which contained numerous simulated fission products)

Plutonium Finishing Plant (PFP) Final Safety Analysis Report (FSAR) [SEC 1 THRU 11

Energy Technology Data Exchange (ETDEWEB)

ULLAH, M K

2001-02-26

The Plutonium Finishing Plant (PFP) is located on the US Department of Energy (DOE) Hanford Site in south central Washington State. The DOE Richland Operations (DOE-RL) Project Hanford Management Contract (PHMC) is with Fluor Hanford Inc. (FH). Westinghouse Safety Management Systems (WSMS) provides management support to the PFP facility. Since 1991, the mission of the PFP has changed from plutonium material processing to preparation for decontamination and decommissioning (D and D). The PFP is in transition between its previous mission and the proposed D and D mission. The objective of the transition is to place the facility into a stable state for long-term storage of plutonium materials before final disposition of the facility. Accordingly, this update of the Final Safety Analysis Report (FSAR) reflects the current status of the buildings, equipment, and operations during this transition. The primary product of the PFP was plutonium metal in the form of 2.2-kg, cylindrical ingots called buttoms. Plutonium nitrate was one of several chemical compounds containing plutonium that were produced as an intermediate processing product. Plutonium recovery was performed at the Plutonium Reclamation Facility (PRF) and plutonium conversion (from a nitrate form to a metal form) was performed at the Remote Mechanical C (RMC) Line as the primary processes. Plutonium oxide was also produced at the Remote Mechanical A (RMA) Line. Plutonium processed at the PFP contained both weapons-grade and fuels-grade plutonium materials. The capability existed to process both weapons-grade and fuels-grade material through the PRF and only weapons-grade material through the RMC Line although fuels-grade material was processed through the line before 1984. Amounts of these materials exist in storage throughout the facility in various residual forms left from previous years of operations.

The US plutonium materials conversion program in Russia

International Nuclear Information System (INIS)

Zygmunt, S.J.; Mason, C.F.V.; Hahn, W.K.

2000-01-01

Progress has been made in Russia towards the conversion of weapons-grade plutonium (w-Pu) into plutonium oxide (PuO 2 ) suitable for further manufacture into mixed oxide (MOX) fuels. This program was started in 1998 in response to US proliferation concerns and the acknowledged international need to decrease the available weapons-grade Pu. A similar agenda is being followed in the US to address disposition of US surplus weapons-grade Pu. In Russia a conversion process has been selected and a site proposed. This paper discusses the present state of the program in support of this future operating facility that will process up to 5 metric tons of plutonium a year. (authors)

Plutonium Proliferation: The Achilles Heel of Disarmament

International Nuclear Information System (INIS)

Leventhal, Paul

2001-01-01

Plutonium is a byproduct of nuclear fission, and it is produced at the rate of about 70 metric tons a year in the world's nuclear power reactors. Concerns about civilian plutonium ran high in the 1970s and prompted enactment of the Nuclear Non-Proliferation Act of 1978 to give the United States a veto over separating plutonium from U.S.-supplied uranium fuel. Over the years, however, so-called reactor-grade plutonium has become the orphan issue of nuclear non-proliferation, largely as a consequence of pressures from plutonium-separating countries. The demise of the fast breeder reactor and the reluctance of utilities to introduce plutonium fuel in light-water reactors have resulted in large surpluses of civilian, weapons-usable plutonium, which now approach in size the 250 tons of military plutonium in the world. Yet reprocessing of spent fuel for recovery and use of plutonium proceeds apace outside the United States and threatens to overwhelm safeguards and security measures for keeping this material out of the hands of nations and terrorists for weapons. A number of historical and current developments are reviewed to demonstrate that plutonium commerce is undercutting efforts both to stop the spread of nuclear weapons and to work toward eliminating existing nuclear arsenals. These developments include the breakdown of U.S. anti-plutonium policy, the production of nuclear weapons by India with Atoms-for-Peace plutonium, the U.S.-Russian plan to introduce excess military plutonium as fuel in civilian power reactors, the failure to include civilian plutonium and bomb-grade uranium in the proposed Fissile Material Cutoff Treaty, and the perception of emerging proliferation threats as the rationale for development of a ballistic missile defense system. Finally, immobilization of separated plutonium in high-level waste is explored as a proliferation-resistant and disarmament-friendly solution for eliminating excess stocks of civilian and military plutonium.

Chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade mixed oxides [(U,Pu)O2

International Nuclear Information System (INIS)

Anon.

1981-01-01

Mixed oxide, a mixture of uranium and plutonium oxides, is used as a nuclear-reactor fuel in the form of pellets. The plutonium content may be up to 10 wt %, and the diluent uranium may be of any U-235 enrichment. In order to be suitable for use as a nuclear fuel, the material must meet certain criteria for combined uranium and plutonium content, effective fissile content, and impurity content. Analytical procedures used to determine if mixed oxides comply with specifications are: uranium by controlled-potential coulometry; plutonium by controlled-potential coulometry; plutonium by amperometric titration with iron (II); nitrogen by distillation spectrophotometry using Nessler reagent; carbon (total) by direct combustion-thermal-conductivity; total chlorine and fluorine by pyrohydrolysis; sulfur by distillation-spectrophotometry; moisture by the coulometric, electrolytic moisture analyzer; isotopic composition by mass spectrometry; rare earths by copper spark spectroscopy; trace impurities by carrier distillation spectroscopy; impurities by spark-source mass spectrography; total gas in reactor-grade mixed dioxide pellets; tungsten by dithiol-spectrophotometry; rare earth elements by spectroscopy; plutonium-238 isotopic abundance by alpha spectrometry; uranium and plutonium isotopic analysis by mass spectrometry; oxygen-to-metal atom ratio by gravimetry

The 'overlooked trio' of hypothetical terrorist nuclear weapons - reactor grade plutonium, neptunium-237 and tritium

International Nuclear Information System (INIS)

Sholly, S.

2002-01-01

Full text: Considerations revolving around physical protection of nuclear material are quite commonly and naturally focused on protecting weapons-grade plutonium (WGPu) and highly enriched uranium (HEU) from theft and diversion. These two materials are the center of attention because of their well-known (and demonstrated) potential for use in first-generation nuclear explosive devices of which potential terrorists are widely thought to be capable. They are also the center of attention because of retirements of these materials from military use as the Russian Federation and the United States reduce the number of nuclear weapons in their arsenals. Three other materials - an 'overlooked trio' - must also be borne in mind within this context: (1) reactor-grade plutonium (RGPu); (2) neptunium-237 (Np-237); and (3) tritium (H-3). Although there are still some authorities who either contend that RGPu cannot be used in a nuclear explosive or that there are (for a terrorist) insurmountable difficulties in doing so, the knowledgeable scientific and technical community, recognizes the potential utility of RGPu for hypothetical terrorist nuclear devices. A much smaller community of experts recognizes the usefulness of Np-237 for nuclear devices, but Np-237 is as straight-forwardly and easily usable as HEU and similarly abundant (but not often in separated form). Tritium can be used (with a modest increase in design sophistication) in a conventional first-generation nuclear device with any of the weapons-usable materials (WGPu, HEU, RGPu or Np-237) to increase the yield and/or increase the reliability of a non-fizzle yield. Given the presence of RGPu and Np-237 in abundant quantities in spent commercial reactor fuel, widely available knowledge of how to separate these materials, and a world-wide total of more than 400 nuclear power plants, spent reactor fuel also requires stringent controls. This is especially true of old spent fuel which has far less radiation dose

A strategy for weapons-grade plutonium disposition

International Nuclear Information System (INIS)

Sylvester, K.W.B.

1994-09-01

A political as well as technical analysis was performed to determine the feasibility of glassification (vitrification) for weapons grade plutonium (WGPu) disposition. The political analysis provided the criteria necessary to compare alternative storage forms. The technical areas of weapon useability and environmental safety were then computationally and experimentally explored and a vitrification implementation strategy postulated. The Monte Carlo Neutron Photon (MCNP) computer code was used to model the effect of blending WGPu with reactor grade Pu (RGPu). A mixture of 30% RGPu and 70% WGPu more than doubled the surface flux from a bare sphere of the mixture which assumedly correlates to a significantly increased predetonation probability. Rare earth diluents were also examined (using MCNP) for their ability to increase the compressed critical mass of the WGPu mixture. The rare earths (notably Eu) were effective in this regard. As Pu-239 has a 24,100 year half life, reactivity control in the long term is an environmental safety issue. Rare earths were investigated as criticality controllers due to their neutron absorption capabilities and insolubility in aqueous environments. Thorium (a Pu surrogate) and the rare earths Eu, Gd, and Sm were added to two standard frits (ARM-1 and SRL-165) and formed into glass. Aqueous leach tests were performed (using MCC-1P guidelines) to measure rare earth leaching and determine the added elements' effects on glass durability. Europium was much more leach resistant than boron in the glasses tested. The elements had no negative effect on the environmental durability of the glasses tested at 90 C and minimal effect at room temperature. No fission product releases were detected in the ARM-1 compositions (which contained numerous simulated fission products)

A strategy for weapons-grade plutonium disposition

Energy Technology Data Exchange (ETDEWEB)

Sylvester, K.W.B. [Iowa State Univ., Ames, IA (United States)

1994-09-01

A political as well as technical analysis was performed to determine the feasibility of glassification (vitrification) for weapons grade plutonium (WGPu) disposition. The political analysis provided the criteria necessary to compare alternative storage forms. The technical areas of weapon useability and environmental safety were then computationally and experimentally explored and a vitrification implementation strategy postulated. The Monte Carlo Neutron Photon (MCNP) computer code was used to model the effect of blending WGPu with reactor grade Pu (RGPu). A mixture of 30% RGPu and 70% WGPu more than doubled the surface flux from a bare sphere of the mixture which assumedly correlates to a significantly increased predetonation probability. Rare earth diluents were also examined (using MCNP) for their ability to increase the compressed critical mass of the WGPu mixture. The rare earths (notably Eu) were effective in this regard. As Pu-239 has a 24,100 year half life, reactivity control in the long term is an environmental safety issue. Rare earths were investigated as criticality controllers due to their neutron absorption capabilities and insolubility in aqueous environments. Thorium (a Pu surrogate) and the rare earths Eu, Gd, and Sm were added to two standard frits (ARM-1 and SRL-165) and formed into glass. Aqueous leach tests were performed (using MCC-1P guidelines) to measure rare earth leaching and determine the added elements` effects on glass durability. Europium was much more leach resistant than boron in the glasses tested. The elements had no negative effect on the environmental durability of the glasses tested at 90 C and minimal effect at room temperature. No fission product releases were detected in the ARM-1 compositions (which contained numerous simulated fission products).

PFP Commercial Grade Food Pack Cans for Plutonium Handling and Storage Critical Characteristics

International Nuclear Information System (INIS)

BONADIE, E.P.

1999-01-01

This document specifies the critical characteristics for Commercial Grade Items (CGI) procured for PFP's Vault Operations system as required by HNF-PRO-268 and HNF-PRO-1819. These are the minimum specifications that the equipment must meet in order to perform its safety function. The changes in these specifications have no detrimental effect on the descriptions and parameters related to handling plutonium solids in the authorization basis. Because no parameters or sequences exceed the limits described in the authorization bases, no accident or abnormal conditions are affected. The specifications prescribed in this critical characteristics document do not represent an unreviewed safety question

The growth and evolution of thin oxide films on delta-plutonium surfaces

Energy Technology Data Exchange (ETDEWEB)

Garcia Flores, Harry G [Los Alamos National Laboratory; Pugmire, David L [Los Alamos National Laboratory

2009-01-01

The common oxides of plutonium are the dioxide (PuO{sub 2}) and the sesquioxide (Pu{sub 2}O{sub 3}). The structure of an oxide on plutonium metal under air at room temperature is typically described as a thick PuO{sub 2} film at the gas-oxide interface with a thinner PuO{sub 2} film near the oxide-metal substrate interface. In a reducing environment, such as ultra high vacuum, the dioxide (Pu{sup 4+}; O/Pu = 2.0) readily converts to the sesquioxide (Pu{sup 3+}; O/Pu = 1.5) with time. In this work, the growth and evolution of thin plutonium oxide films is studied with x-ray photoelectron spectroscopy (XPS) under varying conditions. The results indicate that, like the dioxide, the sesquioxide is not stable on a very clean metal substrate under reducing conditions, resulting in substoichiometric films (Pu{sub 2}O{sub 3-y}). The Pu{sub 2}O{sub 3-y} films prepared exhibit a variety of stoichiometries (y = 0.2-1) as a function of preparation conditions, highlighting the fact that caution must be exercised when studying plutonium oxide surfaces under these conditions and interpreting resulting data.

Contribution of water vapor pressure to pressurization of plutonium dioxide storage containers

Science.gov (United States)

Veirs, D. Kirk; Morris, John S.; Spearing, Dane R.

2000-07-01

Pressurization of long-term storage containers filled with materials meeting the US DOE storage standard is of concern.1,2 For example, temperatures within storage containers packaged according to the standard and contained in 9975 shipping packages that are stored in full view of the sun can reach internal temperatures of 250 °C.3 Twenty five grams of water (0.5 wt.%) at 250 °C in the storage container with no other material present would result in a pressure of 412 psia, which is limited by the amount of water. The pressure due to the water can be substantially reduced due to interactions with the stored material. Studies of the adsorption of water by PuO2 and surface interactions of water with PuO2 show that adsorption of 0.5 wt.% of water is feasible under many conditions and probable under high humidity conditions.4,5,6 However, no data are available on the vapor pressure of water over plutonium dioxide containing materials that have been exposed to water.

Supercritical Fluid Extraction of Plutonium and Americium from Soil

International Nuclear Information System (INIS)

Fox, R.V.; Mincher, B.J.

2002-01-01

Supercritical fluid extraction (SFE) of plutonium and americium from soil was successfully demonstrated using supercritical fluid carbon dioxide solvent augmented with organophosphorus and beta-diketone complexants. Spiked Idaho soils were chemically and radiologically characterized, then extracted with supercritical fluid carbon dioxide at 2,900 psi and 65 C containing varying concentrations of tributyl phosphate (TBP) and thenoyltrifluoroacetone (TTA). A single 45 minute SFE with 2.7 mol% TBP and 3.2 mol% TTA provided as much as 88% ± 6.0 extraction of americium and 69% ± 5.0 extraction of plutonium. Use of 5.3 mol% TBP with 6.8 mol% of the more acidic beta-diketone hexafluoroacetylacetone (HFA) provided 95% ± 3.0 extraction of americium and 83% ± 5.0 extraction of plutonium in a single 45 minute SFE at 3,750 psi and 95 C. Sequential chemical extraction techniques were used to chemically characterize soil partitioning of plutonium and americium in pre-SFE soil samples. Sequential chemical extraction techniques demonstrated that spiked plutonium resides primarily (76.6%) in the sesquioxide fraction with minor amounts being absorbed by the oxidizable fraction (10.6%) and residual fractions (12.8%). Post-SFE soils subjected to sequential chemical extraction characterization demonstrated that 97% of the oxidizable, 78% of the sesquioxide and 80% of the residual plutonium could be removed using SFE. These preliminary results show that SFE may be an effective solvent extraction technique for removal of actinide contaminants from soil

Optimisation of deep burn incineration of reactor waste plutonium in a PBMR DPP-400 core

International Nuclear Information System (INIS)

Serfontein, Dawid E.; Mulder, Eben J.; Reitsma, Frederik

2014-01-01

In this article an original set of coupled neutronics and thermo-hydraulic simulation results for the VSOP 99/05 diffusion code are presented for advanced fuel cycles for the incineration of weapons-grade plutonium, reactor-grade plutonium and reactor-grade plutonium with its associated Minor Actinides in the 400 MW th Pebble Bed Modular Reactor Demonstration Power Plant. These results are also compared to those of the standard 9.6 wt% enriched 9 g/fuel sphere U/Pu fuel cycle. The weapons-grade and reactor-grade plutonium fuel cycles produced good burn-ups. However, the addition of the Minor Actinides to the reactor-grade plutonium caused a large decrease in the burn-up and thus an unacceptable increase in the heavy metal (HM) content in the spent fuel, which was intended for direct disposal in a deep geological repository, without chemical reprocessing. All the plutonium fuel cycles failed the adopted safety limits used in the PBMR400 in that either the maximum fuel temperature of 1130 °C during normal operation, or the maximum power density of 4.5 kW/sphere was exceeded. All the plutonium fuel cycles also produced positive uniform temperature reactivity coefficients, i.e. the reactivity coefficient where the temperatures of the fuel and the graphite moderator in the fuel spheres were varied together. These unacceptable positive coefficients were experienced at low temperatures, typically below 700 °C. This was due to the influence of the thermal fission cross-section resonances of 239 Pu and 241 Pu. Weapons-grade plutonium produced the worst safety performance. The safety performance of the reactor-grade plutonium also deteriorated when the HM loading was reduced from 3 g/sphere to 2 g or 1 g

Optimisation of deep burn incineration of reactor waste plutonium in a PBMR DPP-400 core

Energy Technology Data Exchange (ETDEWEB)

Serfontein, Dawid E., E-mail: Dawid.Serfontein@nwu.ac.za [School for Mechanical and Nuclear Engineering, North West University, PUK-Campus, Private Bag X6001, Internal Post Box 360, Potchefstroom 2520 (South Africa); Mulder, Eben J. [School for Mechanical and Nuclear Engineering, North West University (South Africa); Reitsma, Frederik [Calvera Consultants (South Africa)

2014-05-01

In this article an original set of coupled neutronics and thermo-hydraulic simulation results for the VSOP 99/05 diffusion code are presented for advanced fuel cycles for the incineration of weapons-grade plutonium, reactor-grade plutonium and reactor-grade plutonium with its associated Minor Actinides in the 400 MW{sub th} Pebble Bed Modular Reactor Demonstration Power Plant. These results are also compared to those of the standard 9.6 wt% enriched 9 g/fuel sphere U/Pu fuel cycle. The weapons-grade and reactor-grade plutonium fuel cycles produced good burn-ups. However, the addition of the Minor Actinides to the reactor-grade plutonium caused a large decrease in the burn-up and thus an unacceptable increase in the heavy metal (HM) content in the spent fuel, which was intended for direct disposal in a deep geological repository, without chemical reprocessing. All the plutonium fuel cycles failed the adopted safety limits used in the PBMR400 in that either the maximum fuel temperature of 1130 °C during normal operation, or the maximum power density of 4.5 kW/sphere was exceeded. All the plutonium fuel cycles also produced positive uniform temperature reactivity coefficients, i.e. the reactivity coefficient where the temperatures of the fuel and the graphite moderator in the fuel spheres were varied together. These unacceptable positive coefficients were experienced at low temperatures, typically below 700 °C. This was due to the influence of the thermal fission cross-section resonances of {sup 239}Pu and {sup 241}Pu. Weapons-grade plutonium produced the worst safety performance. The safety performance of the reactor-grade plutonium also deteriorated when the HM loading was reduced from 3 g/sphere to 2 g or 1 g.

Effect of ascorbate ions in DTPA treatment after contamination by mixed plutonium dioxide-sodium burning products

International Nuclear Information System (INIS)

Metivier, H.; Masse, R.; Nolibe, D.; Nenot, J.C.; Lafuma, J.

1977-01-01

Plutonium toxicity problems arising from the use of molten sodium cooled fast breeder reactors involving the accidental mixing and ignition of sodium contaminated by plutonium dioxide have been investigated. The possibility of using the strong reducing agent, ascorbate ion, in order to reduce Pu VI to a chemical form more complexable by DTPA, has been tested using male and female rats. Urine, feces, liver and skeletal measurements of 239 Pu daughter products were carried out. It was shown that the transportable fraction was not significantly modified by the associate ascorbate-DTPA treatment. However the skeletal burden which represents 2.2% with DTPA, reached only 1.6% with ascorbate association and 0.3% with preventive ascorbate injections. Whatever the DTPA ascorbate treatment, the liver burden was not modified significantly. Difference observable only with preventive ascorbate treatment cancels out ascorbate association in order to greatly increase DTPA therapy efficiency, but seems to indicate that the Pu-proteins associations in blood is reduced more easily by ascorbate than association of Pu with local proteins. Ascorbate reduction can also be observed in urinary elimination in that preventive ascorbate, followed by DTPA-ascorbate, leads to a quicker urinary elimination than DTPA or DTPA plus ascorbate post treatment. (U.K.)

Technical challenges in support of the plutonium materials conversion program in Russia

International Nuclear Information System (INIS)

Mason, C.F.V.; Zygmunt, S.J.; Hahn, W.K.; James, C.A.; Costa, D.A.; Smith, W.H.; Yarbro, S.L.

2000-01-01

The Department of Energy's Plutonium Materials Conversion Program for Russia is designed to assist Russia in defining a path for the destruction of weapons grade plutonium. A similar program is currently defining a program for destruction of US weapons grade plutonium. These two sister programs arose from the September 1998 meeting between President Yeltsin and President Clinton, after which they issued a 'Joint statement of principles for management and disposition of plutonium designated as no longer required for defense purposes'. The US and Russia have each committed to convert 50 metric tons of plutonium from nuclear weapons programs to forms which are unusable for weapons

Study on Utilization of Super Grade Plutonium in Molten Salt Reactor FUJI-U3 using CITATION Code

Science.gov (United States)

Wulandari, Cici; Waris, Abdul; Pramuditya, Syeilendra; Asril, Pramutadi AM; Novitrian

2017-07-01

FUJI-U3 type of Molten Salt Reactor (MSR) has a unique design since it consists of three core regions in order to avoid the replacement of graphite as moderator. MSR uses floride as a nuclear fuel salt with the most popular chemical composition is LiF-BeF2-ThF4-233UF4. ThF4 and 233UF4 are the fertile and fissile materials, respectively. On the other hand, LiF and BeF2 working as both fuel and heat transfer medium. In this study, the super grade plutonium will be utilized as substitution of 233U since plutonium is easier to be obtained compared to 233U as main fuel. Neutronics calculation was performed by using PIJ and CITATION modules of SRAC 2002 code with JENDL 3.2 as nuclear data library.

Study on material attractiveness aspect of spent nuclear fuel of LWR and FBR cycles based on isotopic plutonium production

International Nuclear Information System (INIS)

Permana, Sidik; Suzuki, Mitsutoshi; Saito, Masaki; Novitrian,; Waris, Abdul; Suud, Zaki

2013-01-01

Highlights: • The paper analyzes the plutonium production of recycling nuclear fuel option. • To evaluate material attractiveness based on intrinsic feature of material barrier. • Evaluation based on isotopic plutonium composition of spent fuel LWR and FBR. • Even mass number of plutonium gives a significant contribution to material barrier, in particular Pu-238 and Pu-240. • Doping MA in FBR blanket is effective to increase material barrier from weapon grade plutonium to more than MOX fuel grade. - Abstract: Recycling minor actinide (MA) as well as used uranium and plutonium can be considered to reduce nuclear waste production as well as to increase the intrinsic aspect of nuclear nonproliferation as doping material. Plutonium production as a significant aspect of recycling nuclear fuel option, gives some advantages and challenges, such as fissile material utilization of plutonium as well as production of some even mass number plutonium. The study intends to evaluate the material attractiveness based on the intrinsic feature of material barrier such as plutonium composition, decay heat and spontaneous fission neutron components from spent fuel (SF) light water reactor (LWR) and fast breeder reactor (FBR) cycles. A significant contribution has been shown by decay heat (DH) and spontaneous fission neutron (SFN) of even mass number of plutonium isotopes to the total DH and SFN of plutonium element, in particular from isotopic plutonium Pu-238 and Pu-240 contributions. Longer decay cooling time and higher burnup are effective to increase the material barrier (DH and SFN) level from reactor grade plutonium level to MOX grade plutonium level. Material barrier of plutonium element from spent fuel (SF) FBR in the core regions has similarity to the material barrier profile of SF LWR which can be categorized as MOX fuel grade plutonium. Plutonium compositions, DH and SFN components are categorized as weapon grade plutonium level for FBR blanket regions with no

Western Option - Disarmament of Russian Weapon Plutonium

International Nuclear Information System (INIS)

Tveiten, B.; Petroll, M.R.

2002-01-01

The Western Option concept describes an approach to the conversion of weapon-grade plutonium from Russian nuclear warheads under the special aspects of meeting the criteria of irreversible utilization. Putting this concept of plutonium conversion into non-weapon-grade material into effect would make a major contribution to improving security worldwide. This study is based on an agreement between the Russian Federation and the United States of America concluded in September 2000. It provides for the conversion of 34 t of weapon-grade plutonium in each of the two states. This goal is also supported by other G8 countries. While the United States performs its part of the agreement under its sole national responsibility, the Russian program needs financial support by Western states. Expert groups have pointed out several options as a so-called basic scenario. The funds of approx. US Dollar 2 billion required to put them into effect have not so far been raised. The Western Option approach described in this contribution combines results of the basic scenario with other existing experience and with technical solutions available for plutonium conversion. One of the attractions of the Western Option lies in its financial advantages, which are estimated to amount to approx. US Dollar 1 billion. (orig.) [de

Recovery of plutonium from the combustion residues of alpha-bearing solid wastes

International Nuclear Information System (INIS)

Gompper, K.; Wieczorek, H.

1991-01-01

Experimental researches on plutonium dioxide dissolution in nitric acid in inactive and alpha-bearing wastes are presented in this report. After a review of the literature published on dissolution methods of PuO 2 combustion residues. Then results obtained in the ALONA plant on the dissolution of plutonium containing ashes in sulfuric acid and nitric acid are presented. Plutonium purification is studied. At last a simplified scheme of processing based on results obtained

A METHOD OF PREPARING URANIUM DIOXIDE

Science.gov (United States)

Scott, F.A.; Mudge, L.K.

1963-12-17

A process of purifying raw, in particular plutonium- and fission- products-containing, uranium dioxide is described. The uranium dioxide is dissolved in a molten chloride mixture containing potassium chloride plus sodium, lithium, magnesium, or lead chloride under anhydrous conditions; an electric current and a chlorinating gas are passed through the mixture whereby pure uranium dioxide is deposited on and at the same time partially redissolved from the cathode. (AEC)

Nuclear legacy. Democracy in a plutonium economy

International Nuclear Information System (INIS)

Barnaby, F.

1997-01-01

There have already been a few hundred known incidents of nuclear smuggling, mostly of small quantities not close to weapons grade material - but one gram of plutonium is more than sufficient to cause significant harm and to pose a substantial threat. The potential for further thefts is growing as the world produces ever more quantities of plutonium, not only from the dismantling of nuclear weapons but also from the separation out of plutonium from spent uranium nuclear reactor fuel elements. Trying to prevent the theft of gram quantities of plutonium would require levels of protection and surveillance unacceptably high in a democratic society. It is unlikely, therefore, that democracy could survive in a plutonium economy

Removal of plutonium from real time waste using supercritical fluid extraction

International Nuclear Information System (INIS)

Sujatha, K.; Sivaraman, N.; Kumar, R.; Srinivasan, T.G.; Vasudeva Rao, P.R.

2010-01-01

Supercritical fluid extraction (SFE) technique was carried out for the recovery of plutonium from cellulose waste matrix using supercritical carbon dioxide (SC-CO 2 ) modified with suitable ligands such as octylphenyl N,N-diisobutyl carbamoylmethyl phosphine oxide (φCMPO), tri-n-butyl phosphate (TBP), acetyl acetone, trifluoro acetyl acetone and theonyltrifluoroacetyl acetone (TTA). The maximum plutonium recovery was found to be 99.8% when SC-CO 2 modified with CMPO was employed. About 15mg of plutonium was recovered from waste. (author)

Pulmonary carcinogenesis from plutonium-containing particles

International Nuclear Information System (INIS)

Thomas, R.G.; Smith, D.M.; Anderson, E.C.

1980-01-01

Induction of lung tumors by various types of radiation is of paramount concern to the nuclear industry. The data presented were obtained by exposing the pulmonary system of Syrian hamsters to particles of zirconium oxide containing various amounts of either plutonium-238 or -239 as the alpha radiation source. These particles were injected intravenously and lodged permanently in the capillary bed of the lung. When less than 20% of the lung tissue was irradiated, simulating the ''hot particle'' mode, tumors were not evident with lung burdens up to 500 nCi plutonium. More diffuse irradiation significantly increased the tumor incidence, with lung burdens of 50 to 150 nCi. When plutonium-laden microspheres were administered intratracheally, tumor production was considerably increased and the addition of 3 mg of iron oxide intratracheally further increased the incidence. Using the zirconium oxide matrix for the carrier of plutonium in aerosol particles produced tumor incidences of up to 50% in Syrian hamsters exposed by inhalation. Initial pulmonary (alveolar) burdens reached 100 nCi of plutonium. Similar inhalation studies using plutonium dioxide alone (no matrix) failed to produce any increase in lung tumorigenesis. The results are discussed in terms of possible mechanisms necessary for lung carcinogenesis. (H.K.)

Surplus weapons-grade plutonium: a resource for exploring and terraforming Mars

International Nuclear Information System (INIS)

Muscatello, A.C.; Houts, M.G.

1996-01-01

With the end of the Cold War, greater than 100 metric tons (MT) of weapons-grade plutonium (WGPu) have become surplus to defense needs in the United States and the Former Soviet Union. This paper is a proposal for an option for WGPu disposition, i.e., use of the plutonium as a fuel for nuclear reactors for Mars exploration and eventual terraforming. WGPu was used in nuclear weapons because it has a much smaller critical mass than highly enriched uranium, allowing lighter weapons with consequent longer ranges. Similarly, WGPu reactors would also require smaller amounts of fuel to attain a critical mass, making the reactor much lighter overall and resulting in large savings in launch costs. The greater than 100 MT of WGPu would generate about 1000 billion kilowatt hours of heat energy, much of which could be converted into electricity. The waste heat would also be useful to a Martian outpost or colony. A potential way of getting the WGPu reactors into space is a large gas gun like that being developed at the Lawrence Livermore National Laboratory to orbit materials by achieving high velocity at the surface, greatly reducing launch costs and enhancing reliability. Reactor components would be launched on conventional rockets or space shuttles, the reactor fuel rods would be injected into orbit using the gas gun, and the reactor would be assembled in space. Implementation of this proposal would allow disposition of a serious, expensive problem on earth by removing the WGPu from the planet and simultaneously provide a very large energy resource for Mars exploration and terraforming

Surplus weapons-grade plutonium: a resource for exploring and terraforming Mars

Energy Technology Data Exchange (ETDEWEB)

Muscatello, A.C.; Houts, M.G.

1996-12-31

With the end of the Cold War, greater than 100 metric tons (MT) of weapons-grade plutonium (WGPu) have become surplus to defense needs in the United States and the Former Soviet Union. This paper is a proposal for an option for WGPu disposition, i.e., use of the plutonium as a fuel for nuclear reactors for Mars exploration and eventual terraforming. WGPu was used in nuclear weapons because it has a much smaller critical mass than highly enriched uranium, allowing lighter weapons with consequent longer ranges. Similarly, WGPu reactors would also require smaller amounts of fuel to attain a critical mass, making the reactor much lighter overall and resulting in large savings in launch costs. The greater than 100 MT of WGPu would generate about 1000 billion kilowatt hours of heat energy, much of which could be converted into electricity. The waste heat would also be useful to a Martian outpost or colony. A potential way of getting the WGPu reactors into space is a large gas gun like that being developed at the Lawrence Livermore National Laboratory to orbit materials by achieving high velocity at the surface, greatly reducing launch costs and enhancing reliability. Reactor components would be launched on conventional rockets or space shuttles, the reactor fuel rods would be injected into orbit using the gas gun, and the reactor would be assembled in space. Implementation of this proposal would allow disposition of a serious, expensive problem on earth by removing the WGPu from the planet and simultaneously provide a very large energy resource for Mars exploration and terraforming.

Selective recovery of titanium dioxide from low grade sources

CSIR Research Space (South Africa)

Van Vuuren, DS

2006-09-01

Full Text Available that is too fine for use in the chloride process  Perovskite (CaTiO3) resources in Colorado3. The main problem with utilizing a low-grade resource is the amount of chemical wastes produced per unit of pigment of produced. If a TiO2 bearing feedstock... The mineralogical form of the titanium oxide species affects the thermodynamic equilibrium of the reaction. Calcium titanate, CaTiO3 (Perovskite) is more stable than magnesium titanate MgTiO3, (Geikilite) which is more stable than titanium dioxide or ilmenite (Fe...

Process for the preparation of uranium dioxide

International Nuclear Information System (INIS)

Watt, G.W.; Baugh, D.W. Jr.

1981-01-01

A method for the preparation of actinide dioxides using actinide nitrate hexahydrates as starting materials is described. The actinide nitrate hexahydrate is reacted with sodium dithionite, and the product is heated in the absence of oxygen to obtain the dioxide. Preferably, the actinide is uranium, plutonium or neptunium. (LL)

Beating plutonium swords into electrical plowshares

International Nuclear Information System (INIS)

Ofte, D.

1993-01-01

After decades of producing large quantities of weapons-grade plutonium, the United States and the Confederation of Independent States are faced with an unanticipated dilemma of a growing surplus of that material. This circumstance could not have been anticipated just a few years ago after living with a weapons program that from its inception in the United States was characterized by a chronic tight supply situation. The rapid drawdown of the nuclear weapons stockpile presents a near-term problem of storage capacity in the system until the United States makes a disposition decision for what may be in excess of 50 tonnes of weapons-grade plutonium

AN APPROACH TO CHARACTERIZING and EVALUATING ALTERNATIVES FOR THE DECOMMISSIONING OF SUB-GRADE STRUCTURES AT THE PLUTONIUM FINISHING PLANT

International Nuclear Information System (INIS)

HOPKINS, A.M.; KLOS, D.B.

2007-01-01

In 2002, the Richland Operations Office (RL) of the US Department of Energy (DOE), the US Environmental Protection Agency (EPA), and the Washington State Department of Ecology (Ecology) developed milestones for transitioning the Plutonium Finishing Plant (PFP) facility to a clean slab-on-grade configuration. These milestones required developing an engineering evaluation/cost analysis (EF/CA) for the facility's sub-grade structures and installations as part of a series of evaluations intended to provide for the transition of the facility to a clean slab-on-grade configuration. In addition to supporting decisions for interim actions, the analyses of sub-grade structures and installations performed through this EE/CA will contribute to the remedial investigation feasibility study(ies) and subsequently to the final records of decision for the relevant operable units responsible for site closure in the 200 West Area of the Hanford Site

Standard test methods for chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade mixed oxides ((U, Pu)O2)

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 These test methods cover procedures for the chemical, mass spectrometric, and spectrochemical analysis of nuclear-grade mixed oxides, (U, Pu)O2, powders and pellets to determine compliance with specifications. 1.2 The analytical procedures appear in the following order: Sections Uranium in the Presence of Pu by Potentiometric Titration Plutonium by Controlled-Potential Coulometry Plutonium by Amperometric Titration with Iron (II) Nitrogen by Distillation Spectrophotometry Using Nessler Reagent 7 to 14 Carbon (Total) by Direct Combustion-Thermal Conductivity 15 to 26 Total Chlorine and Fluorine by Pyrohydrolysis 27 to 34 Sulfur by Distillation-Spectrophotometry 35 to 43 Moisture by the Coulometric, Electrolytic Moisture Analyzer 44 to 51 Isotopic Composition by Mass Spectrometry Rare Earths by Copper Spark Spectroscopy 52 to 59 Trace Impurities by Carrier Distillation Spectroscopy 60 to 69 Impurities by Spark-Source Mass Spectrography 70 to 76 Total Gas in Reactor-Grade Mixed Dioxide P...

Possibility of plutonium burning out and minor actinides transmutation in CANDU type reactor

International Nuclear Information System (INIS)

Gerasimov, A.S.; Kiselev, G.V.; Myrtsymova, L.A.

2000-01-01

The possibility of power or weapon-grade plutonium use as nuclear fuel in CANDU type reactor with simultaneous minor actinides burn-out is studied. Total thermal power is 1900 MW. The fuel lifetime makes 0.24 years, neutron flux density 10 14 neutr/cm 2 s. About 40-45 % of plutonium is incinerated during fuel lifetime. If weapon-grade plutonium is used in fuel channels instead of power one, its consumption is 40% lower. (author)

Vapor pressures and vapor compositions in equilibrium with hypostoichiometric uranium-plutonium dioxide at high temperatures

International Nuclear Information System (INIS)

Green, D.W.; Fink, J.K.; Leibowitz, L.

1982-01-01

Vapor pressures and vapor compositions in equilibrium with a hypostoichiometric uranium-plutonium dioxide condensed phase (U/sub 1-y/Pu/sub y/)O/sub 2-x/, as functions of T, x, and y, have been calculated for 0.0 less than or equal to x less than or equal to 0.1, 0.0 less than or equal to y less than or equal to 0.3, and for the temperature range 2500 less than or equal to T less than or equal to 6000 K. The range of compositions and temperatures was limited to the region of interest to reactor safety analysis. Thermodynamic functions for the condensed phase and for each of the gaseous species were combined with an oxygen potential model to obtain partial pressures of O, O 2 , Pu, PuO, PuO 2 , U, UO, UO 2 , and UO 3 as functions of T, x, and y

Imaging flow cytometry assays for quantifying pigment grade titanium dioxide particle internalization and interactions with immune cells in whole blood.

Science.gov (United States)

Hewitt, Rachel E; Vis, Bradley; Pele, Laetitia C; Faria, Nuno; Powell, Jonathan J

2017-10-01

Pigment grade titanium dioxide is composed of sub-micron sized particles, including a nanofraction, and is widely utilized in food, cosmetic, pharmaceutical, and biomedical industries. Oral exposure to pigment grade titanium dioxide results in at least some material entering the circulation in humans, although subsequent interactions with blood immune cells are unknown. Pigment grade titanium dioxide is employed for its strong light scattering properties, and this work exploited that attribute to determine whether single cell-particle associations could be determined in immune cells of human whole blood at "real life" concentrations. In vitro assays, initially using isolated peripheral blood mononuclear cells, identified titanium dioxide associated with the surface of, and within, immune cells by darkfield reflectance in imaging flow cytometry. This was confirmed at the population level by side scatter measurements using conventional flow cytometry. Next, it was demonstrated that imaging flow cytometry could quantify titanium dioxide particle-bearing cells, within the immune cell populations of fresh whole blood, down to titanium dioxide levels of 10 parts per billion, which is in the range anticipated for human blood following titanium dioxide ingestion. Moreover, surface association and internal localization of titanium dioxide particles could be discriminated in the assays. Overall, results showed that in addition to the anticipated activity of blood monocytes internalizing titanium dioxide particles, neutrophil internalization and cell membrane adhesion also occurred, the latter for both phagocytic and nonphagocytic cell types. What happens in vivo and whether this contributes to activation of one or more of these different cells types in blood merits further attention. © 2017 International Society for Advancement of Cytometry. © 2017 International Society for Advancement of Cytometry.

Water Solubility of Plutonium and Uranium Compounds and Residues at TA-55

International Nuclear Information System (INIS)

Reilly, Sean Douglas; Smith, Paul Herrick; Jarvinen, Gordon D.; Prochnow, David Adrian; Schulte, Louis D.; DeBurgomaster, Paul Christopher; Fife, Keith William; Rubin, Jim; Worl, Laura Ann

2016-01-01

Understanding the water solubility of plutonium and uranium compounds and residues at TA-55 is necessary to provide a technical basis for appropriate criticality safety, safety basis and accountability controls. Individual compound solubility was determined using published solubility data and solution thermodynamic modeling. Residue solubility was estimated using a combination of published technical reports and process knowledge of constituent compounds. The scope of materials considered includes all compounds and residues at TA-55 as of March 2016 that contain Pu-239 or U-235 where any single item in the facility has more than 500 g of nuclear material. This analysis indicates that the following materials are not appreciably soluble in water: plutonium dioxide (IDC=C21), plutonium phosphate (IDC=C66), plutonium tetrafluoride (IDC=C80), plutonium filter residue (IDC=R26), plutonium hydroxide precipitate (IDC=R41), plutonium DOR salt (IDC=R42), plutonium incinerator ash (IDC=R47), uranium carbide (IDC=C13), uranium dioxide (IDC=C21), U 3 O 8 (IDC=C88), and uranium filter residue (IDC=R26). This analysis also indicates that the following materials are soluble in water: plutonium chloride (IDC=C19) and uranium nitrate (IDC=C52). Equilibrium calculations suggest that PuOCl is water soluble under certain conditions, but some plutonium processing reports indicate that it is insoluble when present in electrorefining residues (R65). Plutonium molten salt extraction residues (IDC=R83) contain significant quantities of PuCl 3 , and are expected to be soluble in water. The solubility of the following plutonium residues is indeterminate due to conflicting reports, insufficient process knowledge or process-dependent composition: calcium salt (IDC=R09), electrorefining salt (IDC=R65), salt (IDC=R71), silica (IDC=R73) and sweepings/screenings (IDC=R78). Solution thermodynamic modeling also indicates that fire suppression water buffered with a commercially-available phosphate

Water Solubility of Plutonium and Uranium Compounds and Residues at TA-55

Energy Technology Data Exchange (ETDEWEB)

Reilly, Sean Douglas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Smith, Paul Herrick [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Jarvinen, Gordon D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Prochnow, David Adrian [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Schulte, Louis D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; DeBurgomaster, Paul Christopher [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Fife, Keith William [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Rubin, Jim [Los Alamos National Lab. (LANL), Los Alamos, NM (United States; Worl, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States

2016-06-13

Understanding the water solubility of plutonium and uranium compounds and residues at TA-55 is necessary to provide a technical basis for appropriate criticality safety, safety basis and accountability controls. Individual compound solubility was determined using published solubility data and solution thermodynamic modeling. Residue solubility was estimated using a combination of published technical reports and process knowledge of constituent compounds. The scope of materials considered includes all compounds and residues at TA-55 as of March 2016 that contain Pu-239 or U-235 where any single item in the facility has more than 500 g of nuclear material. This analysis indicates that the following materials are not appreciably soluble in water: plutonium dioxide (IDC=C21), plutonium phosphate (IDC=C66), plutonium tetrafluoride (IDC=C80), plutonium filter residue (IDC=R26), plutonium hydroxide precipitate (IDC=R41), plutonium DOR salt (IDC=R42), plutonium incinerator ash (IDC=R47), uranium carbide (IDC=C13), uranium dioxide (IDC=C21), U₃O₈ (IDC=C88), and uranium filter residue (IDC=R26). This analysis also indicates that the following materials are soluble in water: plutonium chloride (IDC=C19) and uranium nitrate (IDC=C52). Equilibrium calculations suggest that PuOCl is water soluble under certain conditions, but some plutonium processing reports indicate that it is insoluble when present in electrorefining residues (R65). Plutonium molten salt extraction residues (IDC=R83) contain significant quantities of PuCl₃, and are expected to be soluble in water. The solubility of the following plutonium residues is indeterminate due to conflicting reports, insufficient process knowledge or process-dependent composition: calcium salt (IDC=R09), electrorefining salt (IDC=R65), salt (IDC=R71), silica (IDC=R73) and sweepings/screenings (IDC=R78). Solution thermodynamic modeling also indicates that fire suppression water buffered with a

Synthesis of complex plutonium oxides with alkaline-earth metals

International Nuclear Information System (INIS)

Suzuki, Yasufumi; Nakajima, Kunihisa; Iwai, Takashi; Ohmichi, Toshihiko; Yamawaki, Michio.

1995-03-01

Complex plutonium(IV) oxides with strontium and barium, SuPuO 3 and BaPuO 3 , were synthesized and their crystal structure was analyzed. Compacted mixture of plutonium dioxide powder and the carbonate of strontium or barium was heated in a stream of argon gas using a cell with a small orifice. The products obtained were found to be composed of a nearly single phase showing the structure of orthorhombic slightly distorted from cubic. (author)

Quantitative analysis of carbon in plutonium

International Nuclear Information System (INIS)

Lefevre, Chantal.

1979-11-01

The aim of this study is to develop a method for the determination of carbon traces (20 to 400 ppm) in plutonium. The development of a carbon in plutonium standard is described, then the content of this substance is determined and its validity as a standard shown by analysis in two different ways. In the first method used, reaction of the metal with sulphur and determination of carbon as carbon sulphide, the following parameters were studied: influence of excess reagent, surface growth of samples in contact with sulphur, temperature and reaction time. The results obtained are in agreement with those obtained by the conventional method of carbon determination, combustion in oxygen and measurement of carbon in the form of carbon dioxide. Owing to the presence of this standard we were then able to study the different parameters involved in plutonium combustion so that the reaction can be made complete: temperature reached during combustion, role of flux, metal surface in contact with oxygen and finally method of cleaning plutonium samples [fr

Continuous plutonium(IV) oxalate precipitation, filtration, and calcination process. [From product streams from Redox, Purex, or Recuplex solvent extraction plants

Energy Technology Data Exchange (ETDEWEB)

Beede, R L

1956-09-27

A continuous plutonium (IV) oxalate precipitation, filtration, and calcination process has been developed. Continuous and batch decomposition of the oxalate in the filtrates has been demonstrated. The processes have been demonstrated in prototype equipment. Plutonium (IV) oxalate was precipitated continuously at room temperature by the concurrent addition of plutonium (IV) nitrate feed and oxalic acid into the pan of a modified rotary drum filter. The plutonium (IV) oxalate was calcined to plutonium dioxide, which could be readily hydrofluorinated. Continuous decomposition of the oxalate in synthetic plutonium (IV) oxalate filtrates containing plutonium (IV) oxalate solids was demonstrated using co-current flow in a U-shaped reactor. Feeds containing from 10 to 100 g/1 Pu, as plutonium (IV) nitrate, and 1.0 to 6.5 M HNO/sub 3/, respectively, can be processed. One molar oxalic acid is used as the precipitant. Temperatures of 20 to 35/sup 0/C for the precipitation and filtration are satisfactory. Plutonium (IV) oxalate can be calcined at 300 to 400/sup 0/C in a screw-type drier-calciner to plutonium dioxide and hydrofluorinated at 450 to 550/sup 0/C. Plutonium dioxide exceeding purity requirements has been produced in the prototype equipment. Advantages of continuous precipitation and filtration are: uniform plutonium (IV) oxalate, improved filtration characteristics, elimination of heating and cooling facilities, and higher capacities through a single unit. Advantages of the screw-type drier-calciner are the continuous production of an oxide satisfactory for feed for the proposed plant vibrating tube hydrofluorinator, and ease of coupling continuous precipitation and filtration to this proposed hydrofluorinator. Continuous decomposition of oxalate in filtrates offers advantages in decreasing filtrate storage requirements when coupled to a filtrate concentrator. (JGB)

Minimization of the fission product waste by using thorium based fuel instead of uranium dioxide

Energy Technology Data Exchange (ETDEWEB)

Galahom, A. Abdelghafar, E-mail: Agalahom@yahoo.com

2017-04-01

This research discusses the neutronic characteristics of VVER-1200 assembly fueled with five different fuel types based on thorium. These types of fuel based on mixing thorium as a fertile material with different fissile materials. The neutronic characteristics of these fuels are investigated by comparing their neutronic characteristics with the conventional uranium dioxide fuel using the MCNPX code. The objective of this study is to reduce the production of long-lived actinides, get rid of plutonium component and to improve the fuel cycle economy while maintaining acceptable values of the neutronic safety parameters such as moderator temperature coefficient, Doppler coefficient and effective delayed neutrons (β). The thorium based fuel has a more negative Doppler coefficient than uranium dioxide fuel. The moderator temperature coefficient (MTC) has been calculated for the different proposed fuels. Also, the fissile inventory ratio has been calculated at different burnup step. The use of Th-232 as a fertile material instead of U-238 in a nuclear fuel is the most promising fuel in VVER-1200 as it is the ideal solution to avoid the production of more plutonium components and long-lived minor actinides. The reactor grade plutonium accumulated in light water reactor with burnup can be recycled by mixing it with Th-232 to fuel the VVER-1200 assembly. The concentrations of Xe-135 and Sm-151 have been investigated, due to their high thermal neutron absorption cross section.

Pharmaceutical/food grade titanium dioxide particles are absorbed into the bloodstream of human volunteers.

Science.gov (United States)

Pele, Laetitia C; Thoree, Vinay; Bruggraber, Sylvaine F A; Koller, Dagmar; Thompson, Richard P H; Lomer, Miranda C; Powell, Jonathan J

2015-09-02

Exposure to persistent engineered nano and micro particles via the oral route is well established. Animal studies have demonstrated that, once ingested, a small proportion of such particles translocate from the gastrointestinal tract to other tissues. Exposure to titanium dioxide is widespread via the oral route, but only one study has provided indirect evidence (total titanium analyses) of absorption into the blood stream in humans. We sought to replicate these observations and to provide additional evidence for particulate uptake. Human volunteers with normal intestinal permeability were orally administered 100 mg pharmaceutical/food grade titanium dioxide. Blood samples were collected from 0.5 to 10 h post ingestion and analysed for the presence of reflectant bodies (particles) by dark field microscopy, and for total titanium by inductively coupled plasma mass spectrometry (ICP-MS). Blood film analyses implied early absorption of particles (2 h) with a peak maximum at 6 h following ingestion. The presence of these reflectant particles in blood roughly mirrored the levels of total titanium by ICP-MS, providing good evidence for the latter being a measure of whole particle (titanium dioxide) absorption. This study shows that a fraction of pharmaceutical/food grade titanium dioxide is absorbed systemically by humans following ingestion. It confirms that at least two routes of particle uptake may exist in the human gut- one proximal and one distal. Further work should quantify human exposure and uptake of such persistent particles.

The radiological hazard of plutonium isotopes and specific plutonium mixtures

International Nuclear Information System (INIS)

Heindel, G.; Clow, J.; Inkret, W.; Miller, G.

1995-11-01

The US Department of Energy defines the hazard categories of its nuclear facilities based upon the potential for accidents to have significant effects on specific populations and the environment. In this report, the authors consider the time dependence of hazard category 2 (significant on-site effects) for facilities with inventories of plutonium isotopes and specific weapons-grade and heat-source mixtures of plutonium isotopes. The authors also define relative hazard as the reciprocal of the hazard category 2 threshold value and determine its time dependence. The time dependence of both hazard category 2 thresholds and relative hazards are determined and plotted for 10,000 years to provide useful information for planning long-term storage or disposal facilities

Preconcentration of plutonium radionuclides from natural waters

International Nuclear Information System (INIS)

Wong, K.M.; Nioshkin, V.E.; Jokela, T.A.

1978-02-01

A large volume water sampler using manganese dioxide impregnated cartridges for the in situ separation of plutonium in sea water and ground water was studied. Plutonium concentrations obtained by this technique are compared with a radiochemical coprecipitation method. Consistent results were obtained between the two methods for water samples from the Pacific Ocean and Enewetak lagoon. Different results were noted from samples collected in the Enewetak reef and ground water stations. Using this preconcentration technique and the coprecipitation method it was shown that the physical-chemical characteristics of Pu in Enewetak reef and ground water are different from the lagoon and open ocean

Plutonium immobilization program - Cold pour Phase 1 test results

International Nuclear Information System (INIS)

Hamilton, L.

2000-01-01

The Plutonium Immobilization Project will disposition excess weapons grade plutonium. It uses the can-in-canister approach that involves placing plutonium-ceramic pucks in sealed cans that are then placed into Defense Waste Processing Facility canisters. These canisters are subsequently filled with high-level radioactive waste glass. This process puts the plutonium in a stable form and makes it unattractive for reuse. A cold (non-radioactive) glass pour program was performed to develop and verify the baseline design for the canister and internal hardware. This paper describes the Phase 1 scoping test results

Plutonium Immobilization Program - Cold pour Phase 1 test results

International Nuclear Information System (INIS)

Hamilton, L.

2000-01-01

The Plutonium Immobilization Project will disposition excess weapons grade plutonium. It uses the can-in-canister approach that involves placing plutonium-ceramic pucks in sealed cans that are then placed into Defense Waste Processing Facility canisters. These canisters are subsequently filled with high-level radioactive waste glass. This process puts the plutonium in a stable form and makes it unattractive for reuse. A cold (non-radioactive) glass pour program was performed to develop and verify the baseline design for the canister and internal hardware. This paper describes the Phase 1 scoping test results

Physicochemical characterization of discrete weapons grade plutonium metal particles originating from the 1960 BOMARC incident

Science.gov (United States)

Bowen, James M.

The goal of this research was to investigate the physicochemical properties of weapons grade plutonium particles originating from the 1960 BOMARC incident for the purpose of predicting their fate in the environment and to address radiation protection and nuclear security concerns. Methods were developed to locate and isolate the particles in order to characterize them. Physical, chemical, and radiological characterization was performed using a variety of techniques. And finally, the particles were subjected to a sequential extraction procedure, a series of increasingly aggressive reagents, to simulate an accelerated environmental exposure. A link between the morphology of the particles and their partitioning amongst environmental mechanisms was established.

The effects of immune modulation on plutonium dioxide lung carcinogenesis in the rat

International Nuclear Information System (INIS)

Nolibe, D.; Discour, M.; Masse, R.; Lafuma, J.

1979-01-01

After inhalation of radioactive particles only some rats developed lung tumors. It was interesting to see whether this was a random effect or the result of different individual susceptibilities. Among the possible individual differences, cell mediated mechanisms and genetic factors have been reported. The relationships between cancerogenesis and host immune status are tested on rats submitted to an inhalation of plutonium dioxide particles after depression by azathioprine, hydrocortisone or thymectomy. The effects of immuno stimulation by BCG are also studied. The influence of genetic factors is studied with the same protocol on two strains of Wistar rats outbred or inbred. The incidence, nature, size, extension and metastases of tumors are compared between the groups. Results give a good evidence that AZA treated rats and thymectomized rats have a greater incidence of spontaneous tumors. This effect is observed at different levels in the two strains of rats. According to strain used, immunodepression have no or weak enhancing effect on PuO 2 tumor induction, but significant effect of development of tumors is always observed. A shift towards bronchogenic type is also observed. BCG have also an enhancing effect on development of tumors and no protective effect on their incidence

Conceptual Design for the Pilot-Scale Plutonium Oxide Processing Unit in the Radiochemical Processing Laboratory

Energy Technology Data Exchange (ETDEWEB)

Lumetta, Gregg J.; Meier, David E.; Tingey, Joel M.; Casella, Amanda J.; Delegard, Calvin H.; Edwards, Matthew K.; Jones, Susan A.; Rapko, Brian M.

2014-08-05

This report describes a conceptual design for a pilot-scale capability to produce plutonium oxide for use as exercise and reference materials, and for use in identifying and validating nuclear forensics signatures associated with plutonium production. This capability is referred to as the Pilot-scale Plutonium oxide Processing Unit (P3U), and it will be located in the Radiochemical Processing Laboratory at the Pacific Northwest National Laboratory. The key unit operations are described, including plutonium dioxide (PuO2) dissolution, purification of the Pu by ion exchange, precipitation, and conversion to oxide by calcination.

Accelerator-driven assembly for plutonium transformation (ADAPT)

Science.gov (United States)

Tuyle, Greorgy J. Van; Todosow, Michael; Powell, James; Schweitzer, Donald

1995-01-01

A particle accelerator-driven spallation target and corresponding blanket region are proposed for the ultimate disposition of weapons-grade plutonium being retired from excess nuclear weapons in the U.S. and Russia. The highly fissle plutonium is contained within .25 to .5 cm diameter silicon-carbide coated graphite beads, which are cooled by helium, within the slightly subcritical blanket region. Major advantages include very high one-pass burnup (over 90%), a high integrity waste form (the coated beads), and operation in a subcritical mode, thereby minimizing the vulnerability to the positive reativity feedbacks often associated with plutonium fuel.

Long-term behavior of refractory thorium-plutonium dioxide solid solutions

Energy Technology Data Exchange (ETDEWEB)

Claparede, Laurent, E-mail: laurent.claparede@umontpellier.fr [ICSM, UMR 5257 CNRS/CEA/Univ. Montpellier/ENSCM, Site de Marcoule, Bât. 426, BP 17171, 30207 Bagnols/Cèze (France); Guigue, Mireille [CEA, Nuclear Energy Division, RadioChemistry & Processes Department, BP 17171, 30207 Bagnols/Cèze (France); Jouan, Gauthier [CEA, Nuclear Energy Division, DTEC Department, BP 17171, 30207 Bagnols/Cèze (France); Nadah, Nassima [CEA, Nuclear Energy Division, RadioChemistry & Processes Department, BP 17171, 30207 Bagnols/Cèze (France); Dacheux, Nicolas [ICSM, UMR 5257 CNRS/CEA/Univ. Montpellier/ENSCM, Site de Marcoule, Bât. 426, BP 17171, 30207 Bagnols/Cèze (France); Moisy, Philippe [CEA, Nuclear Energy Division, RadioChemistry & Processes Department, BP 17171, 30207 Bagnols/Cèze (France)

2017-01-15

The long-term behavior of Th{sub 0.87}Pu{sub 0.13}O{sub 2} was examined in nitric acid concentrations. The normalized dissolution rates after 3380 days, range from (1.4 ± 0.2) × 10{sup −6} g m{sup −2} d{sup −1} in 5 M HNO{sub 3} down to (3.2 ± 0.4) × 10{sup −8} g m{sup −2} d{sup −1} in 10{sup −3} M HNO{sub 3}, which confirms the high chemical durability of this solid solution. The amounts of plutonium measured in solution lead to 0.9% and 2.1% of dissolved solid in 1 M and 5 M HNO{sub 3}, respectively. In such conditions, the time required to reach the full dissolution of the material varies from 430 years (5 M HNO{sub 3}) to 18,000 years (10{sup −3} M HNO{sub 3}). Moreover, the partial order related to the proton activity (n = 0.45 ± 0.03) suggests that the dissolution is mainly driven by surface reactions occurring at the solid/liquid interface. The characterization of the leached samples by SEM shows small microstructural modifications (i.e. detachment of crystallites) and the absence of neoformed phase while from PXRD, the unit cell parameter and crystallite size are not significantly affected. - Highlights: • Leaching tests of Th{sub 0.87}Pu{sub 0.13}O{sub 2} were performed for 9 years in several nitric acid solutions. • The high chemical durability of thorium-plutonium oxide solid solutions was confirmed. • The solubility of plutonium(IV) was not controlled by the precipitation of plutonium tetrahydroxide in these experiments.

Disposition of weapons-grade plutonium in LWRs - a utility perspective

International Nuclear Information System (INIS)

Naughton, W.F.

1996-01-01

The optimal alternative for the disposition of weapons-grade plutonium (WPu) is to burn it in currently operating light water reactors (LWRs). There are three key aspects associated with the reactor burn option that lead to this conclusion. They are timeliness, acceptable solution, and equity or resource recovery. The National Academy of Sciences report on this subject has thoroughly covered the first two aspects by indicating that there is open-quotes a clear and present dangerclose quotes associated with WPu - the timeliness issue. Also, the report indicates that the spent-fuel standard is the acceptable long-term solution. Both of these aspects are met by the reactor burn option as it exists today; i.e., the reactor option is both timely and obviously meets the spent-fuel standard. The equity or resource recovery aspect is based on the fact that the resources for the development and use of this material as a nuclear deterrent for the past 50 yr was supplied by, in the U.S.'s case, the taxpayers. Only the reactor burn option offers an opportunity for the partial recovery of those resources in the form of electrical energy

The toxicological study of plutonium: tumor-inducing effect of plutonium in rats

International Nuclear Information System (INIS)

Chen Rusong; Zhao Yongchan; Wang Shoufang; Li Maohe

1992-09-01

The carcinogenic effects of Pu compounds through different routs of administration are introduced. The following results have been obtained: (1) Pu is really a powerful carcinogenic radionuclide. (2) Osteosarcoma can be induced in rats by plutonium nitrate at low level radiation. The incidence is from 38.9% to 42.9% in the 185 kBq/kg group. (3) Lung cancer can be induced by plutonium dioxide and the biological effect of TLN (thoracic lymph node) is significant. (4) Under the combined treatment of 239 Pu, 90 Sr and 144 Ce, the carcinogenic effects is much greater than their separative effect on rats. (5) By using the method of comparative toxicology, the risk of osteosarcoma induced by Pu in human is about 600/(10 6 man·cGy) which is extrapolated from animal to human. The above conclusions are important for evaluating the potential hazard of Pu to human beings

Plutonium Disposition Now exclamation point

International Nuclear Information System (INIS)

Buckner, M.R.

1995-01-01

A means for use of existing processing facilities and reactors for plutonium disposition is described which requires a minimum capital investment and allows rapid implementation. The scenario includes interim storage and processing under IAEA control, and fabrication into MOX fuel in existing or planned facilities in Europe for use in operating reactors in the two home countries. Conceptual studies indicate that existing Westinghouse four-loop designs can safety dispose of 0.94 MT of plutonium per calendar year. Thus, it would be possible to consume the expected US excess stockpile of about 50 MT in two to three units of this type, and it is highly likely that a comparable amount of the FSU excess plutonium could be deposed of in a few VVER-1000's. The only major capital project for this mode of plutonium disposition would be the weapons-grade plutonium processing which could be done in a dedicated international facility or using existing facilities in the US and FSU under IAEA control. This option offers the potential for quick implementation at a very low cost to the governments of the two countries

Combining a gas turbine modular helium reactor and an accelerator and for near total destruction of weapons grade plutonium

Energy Technology Data Exchange (ETDEWEB)

Baxter, A.M.; Lane, R.K.; Sherman, R. [General Atomics, San Diego, CA (United States)

1995-10-01

Fissioning surplus weapons-grade plutonium (WG-Pu) in a reactor is an effective means of rendering this stockpile non-weapons useable. In addition the enormous energy content of the plutonium is released by the fission process and can be captured to produce valuable electric power. While no fission option has been identified that can accomplish the destruction of more than about 70% of the WG-Pu without repeated reprocessing and recycling, which presents additional opportunities for diversion, the gas turbine modular helium-cooled reactor (GT-MHR), using an annular graphite core and graphite inner and outer reflectors combines the maximum plutonium destruction and highest electrical production efficiency and economics in an inherently safe system. Accelerator driven sub-critical assemblies have also been proposed for WG-Pu destruction. These systems offer almost complete WG-Pu destruction, but achieve this goal by using circulating aqueous or molten salt solutions of the fuel, with potential safety implications. By combining the GT-MHR with an accelerator-driven sub-critical MHR assembly, the best features of both systems can be merged to achieve the near total destruction of WG-Pu in an inherently safe, diversion-proof system in which the discharged fuel elements are suitable for long term high level waste storage without the need for further processing. More than 90% total plutonium destruction, and more than 99.9% Pu-239 destruction, could be achieved. The modular concept minimizes the size of each unit so that both the GT-MHR and the accelerator would be straightforward extensions of current technology.

Formation, characterization, and stability of plutonium (IV) colloid

International Nuclear Information System (INIS)

Hobart, D.E.; Morris, D.E.; Palmer, P.D.; Newton, T.W.

1989-01-01

Plutonium is expected to be a major component of the waste element package in any high-level nuclear waste repository. Plutonium(IV) is known to form colloids under chemical conditions similar to those found in typical groundwaters. In the event of a breach of a repository, these colloids represent a source of radionuclide transport to the far-field environment, in parallel with the transport of dissolved waste element species. In addition, the colloids may decompose or disaggregate into soluble ionic species. Thus, colloids represent an additional term in determining waste element solubility limits. A thorough characterization of the physical and chemical properties of these colloids under relevant conditions is essential to assess the concentration limits and transport mechanisms for the waste elements at the proposed Yucca Mountain Repository site. This report is concerned primarily with recent results obtained by the Yucca Mountain Project (YMP) Solubility Determination Task pertaining to the characterization of the structural and chemical properties of Pu(IV) colloid. Important results will be presented which provides further evidence that colloidal plutonium(IV) is structurally similar to plutonium dioxide and that colloidal plutonium(IV) is electrochemically reactive. 13 refs., 7 figs

Development of advanced mixed oxide fuels for plutonium management

International Nuclear Information System (INIS)

Eaton, S.; Beard, C.; Buksa, J.; Butt, D.; Chidester, K.; Havrilla, G.; Ramsey, K.

1997-01-01

A number of advanced Mixed Oxide (MOX) fuel forms are currently being investigated at Los Alamos National Laboratory that have the potential to be effective plutonium management tools. Evolutionary Mixed Oxide (EMOX) fuel is a slight perturbation on standard MOX fuel, but achieves greater plutonium destruction rates by employing a fractional nonfertile component. A pure nonfertile fuel is also being studied. Initial calculations show that the fuel can be utilized in existing light water reactors and tailored to address different plutonium management goals (i.e., stabilization or reduction of plutonium inventories residing in spent nuclear fuel). In parallel, experiments are being performed to determine the feasibility of fabrication of such fuels. Initial EMOX pellets have successfully been fabricated using weapons-grade plutonium. (author)

Development of advanced mixed oxide fuels for plutonium management

International Nuclear Information System (INIS)

Eaton, S.; Beard, C.; Buksa, J.; Butt, D.; Chidester, K.; Havrilla, G.; Ramsey, K.

1997-06-01

A number of advanced Mixed Oxide (MOX) fuel forms are currently being investigated at Los Alamos National Laboratory that have the potential to be effective plutonium management tools. Evolutionary Mixed Oxide (EMOX) fuel is a slight perturbation on standard MOX fuel, but achieves greater plutonium destruction rates by employing a fractional nonfertile component. A pure nonfertile fuel is also being studied. Initial calculations show that the fuel can be utilized in existing light water reactors and tailored to address different plutonium management goals (i.e., stabilization or reduction of plutonium inventories residing in spent nuclear fuel). In parallel, experiments are being performed to determine the feasibility of fabrication of such fuels. Initial EMOX pellets have successfully been fabricated using weapons-grade plutonium

Long-term plutonium storage: Design concepts

International Nuclear Information System (INIS)

Wilkey, D.D.; Wood, W.T.; Guenther, C.D.

1994-01-01

An important part of the Department of Energy (DOE) Weapons Complex Reconfiguration (WCR) Program is the development of facilities for long-term storage of plutonium. The WCR design goals are to provide storage for metals, oxides, pits, and fuel-grade plutonium, including material being held as part of the Strategic Reserve and excess material. Major activities associated with plutonium storage are sorting the plutonium inventory, material handling and storage support, shipping and receiving, and surveillance of material in storage for both safety evaluations and safeguards and security. A variety of methods for plutonium storage have been used, both within the DOE weapons complex and by external organizations. This paper discusses the advantages and disadvantages of proposed storage concepts based upon functional criteria. The concepts discussed include floor wells, vertical and horizontal sleeves, warehouse storage on vertical racks, and modular storage units. Issues/factors considered in determining a preferred design include operational efficiency, maintenance and repair, environmental impact, radiation and criticality safety, safeguards and security, heat removal, waste minimization, international inspection requirements, and construction and operational costs

The plutonium challenge for the future

International Nuclear Information System (INIS)

Gray, L.W.

2000-01-01

In this paper author deal with the weapons-usable plutonium and with the possibilities of their managing. Russia has not disclosed the amount of plutonium produced, but various estimates indicate that the production was about 130 tonnes. Production has been curtailed in Russia; three dual-purpose reactors still produce weapons-grade plutonium - two at Tomsk-7 (renamed Seversk) and one at Krasnoyarsk-26 (renamed Zheleznogorsk Mining and Chemical Combine). In a 1994 United States-Russian agreement that has yet to enter into force, Russia agreed to close the remaining operating reactors by the year 2000. Treaties between the United States and Russia have already cut the number of nuclear warheads from more than 10,000 to about 6,000 under START 1, which has been ratified, and to about 3,500 under START 2, which still awaits approval. If Russia and the United States conclude START 3, that number could drop to between 2,000 and 2,500. On September 2, 1998, the Presidents of the United States and Russia signed the 'Joint statement of principles for Management and Disposition of Plutonium, Designated as No Longer Required for Defense Purposes.' In this joint statement the Presidents affirm the intention of each country to remove by stages approximately 50 metric tons of plutonium and to convert the nuclear weapons programs, and to convert this material so that it can never be used in nuclear weapons. These 100 tonne of plutonium must be managed in proper way such that it becomes neither a proliferation for an environmental risk. The United States has proposed that it manage it's 50 tonnes by a dual approach-once through MOX burning of a portion of the plutonium and immobilization in a ceramic matrix followed by en- casement in high level waste glass. Russia has proposed that it manage its full 50 tonnes by burning in a reactor. The MOX program in the United States would bum the cleaner plutonium metal and residues. Weapons components would be converted to plutonium oxide

A vitrification strategy for weapons-grade plutonium disposition

International Nuclear Information System (INIS)

Sylvester, K.B.; Simonson, S.A.

1995-01-01

Excess weapons-grade plutonium (WGPu) presents a complex but welcome challenge to decision makers. High security is a clear priority but a host of concerns will impact US actions. Making disposition decisions based on a rigid set of criteria designed to identify an 'optimum' technology given immediate objectives and available technologies may delay Russian processing and unnecessarily limit US options. Attention should be given to near-term, verifiable options that may not provide an acceptable level of security in the long-term but nonetheless provide a material barrier to direct theft and immediate use, buying time to evaluate potential disposition technologies. Vitrification of WGPu in borosilicate glass was examined as one such alternative. Rare earth diluents were examined (using MCNP) for their ability to increase the compressed critical mass of the mixture. Increased critical mass complicates weapon design and increases the quantity of material necessarily diverted. Europium was effective in this regard. As Pu-239 has a 24,000 yr half-life, reactivity control in the long-term could be an environmental safety issue should the glass be placed in a repository. Rare earths were investigated as criticality controllers due to their neutron absorption capabilities and insolubility in aqueous environments. Thorium (assumed as a Pu surrogate) and the rare earths Eu, Gd, and Sm were added to a standard frit (SRL-165) and formed into glass. Aqueous leach tests were performed (using MCC-1P guidelines) to measure rare earth leaching and determine the added element's effects on glass durability

Exploiting the plutonium stockpiles in PWRs by using inert matrix fuel

International Nuclear Information System (INIS)

Lombardi, C.; Mazzola, A.

1996-01-01

The plutonium coming from dismantled warheads and that already stockpiled coming from spent fuel reprocessing have raised many concerns related to proliferation resistance, environmental safety and economy. The option of disposing of plutonium by fission is one of the most widely discussed and many proposals for plutonium burning in a safe and economical manner have been put forward. Due to their diffusion, PWRs appear to be the main candidates for the reduction of the plutonium stockpiles. In order to achieve a high plutonium consumption rate, a uranium-free fuel may be conceived, based on the dilution of PuO 2 within a carrier matrix made of inert oxide. In this paper, a partial loading of inert matrix fuel in a current technology PWR was investigated with 3-D calculations. The results indicated that this solution has good plutonium elimination capabilities: commercial PWRs operating in a once-through cycle scheme can transmute more than 98% of the loaded Pu-239 and 73 or 81% of the overall initially loaded reactor grade or weapons grade plutonium, respectively. The plutonium still let in the spent fuel was of poor quality and then offered a better proliferation resistance. Power peaking problems could be faced with the adoption of burnable absorbers: IFBA seemed to be particularly suitable. In spite of a reduction of the overall plutonium loaded mass by a factor 3.7 or 5.4 depending on its quality, there was no evidence of an increase of the minor actinides radiotoxicity after a time period of about 25 years. (author)

MIS High-Purity Plutonium Oxide Hydride Product 5501579 (SSR124): Final Report

Energy Technology Data Exchange (ETDEWEB)

Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stroud, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Berg, John M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Narlesky, Joshua Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Worl, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinex, Max A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carillo, Alex [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2018-02-08

A high-purity plutonium dioxide material from the Material Identification and Surveillance (MIS) Program inventory has been studied with regard to gas generation and corrosion in a storage environment. Sample 5501579 represents process plutonium oxides from hydride oxide from Rocky Flats that are currently stored in 3013 containers. After calcination to 950°C, the material contained 87.42% plutonium with no major impurities. This study followed over time, the gas pressure of a sample with nominally 0.5 wt% water in a sealed container with an internal volume scaled to 1/500th of the volume of a 3013 container. Gas compositions were measured periodically over a six year period. The maximum observed gas pressure was 124 kPa. The increase over the initial pressure of 70 kPa was primarily due to generation of nitrogen and carbon dioxide gas. Hydrogen and oxygen were minor components of the headspace gas. At the completion of the study, the internal components of the sealed container showed signs of corrosion.

Plutonium uptake by a soil fungus and transport to its spores

International Nuclear Information System (INIS)

Beckert, W.F.; Au, F.H.F.

1976-01-01

Three concentrations of plutonium-238 nitrate, citrate and dioxide were each added to separate plates of malt agar buffered to pH 2.5 and 5.5 to determine the uptake of plutonium from these chemical forms and concentrations by a common soil fungus, Aspergillus niger. After inoculation and incubation, the aerial spores of Aspergillus niger were collected using a technique that excluded the possibility of cross-contamination of the spores by the culture media or by mycelial fragments. 238 Pu was taken up from all three chemical forms and transported to the aerial spores of Aspergillus niger at each concentration and at both pH levels. The specific activities of the spores grown at pH 5.5 were generally at least twice those of the spores grown at pH 2.5. The uptake of plutonium from the dioxide form was about one-third of that from the nitrate and citrate forms at both pH levels. The term 'transport factor' is used as a means to compare the transport of plutonium from the media to the fungal spores; the concentration-independent transport factor is defined as the specific activity of the spores divided by the specific activity of the dry culture medium. Though the transport factors were less than 1, which indicates discrimination against the transport of 238 Pu from the culture media to the spores, these findings suggest that this common soil fungus may be solubilizing soil-deposited plutonium and rendering it more biologically available for higher plants and animals. (author)

Reactor-Based Plutonium Disposition: Opportunities, Options, and Issues

International Nuclear Information System (INIS)

Greene, S.R.

1999-01-01

The end of the Cold War has created a legacy of surplus fissile materials (plutonium and highly enriched uranium) in the United States (U.S.) and the former Soviet Union. These materials pose a danger to national and international security. During the past few years, the U.S. and Russia have engaged in an ongoing dialog concerning the safe storage and disposition of surplus fissile material stockpiles. In January 1997, the Department of Energy (DOE) announced the U. S. would pursue a dual track approach to rendering approximately 50 metric tons of plutonium inaccessible for use in nuclear weapons. One track involves immobilizing the plutonium by combining it with high-level radioactive waste in glass or ceramic ''logs''. The other method, referred to as reactor-based disposition, converts plutonium into mixed oxide (MOX) fuel for nuclear reactors. The U.S. and Russia are moving ahead rapidly to develop and demonstrate the technology required to implement the MOX option in their respective countries. U.S. MOX fuel research and development activities were started in the 1950s, with irradiation of MOX fuel rods in commercial light water reactors (LWR) from the 1960s--1980s. In all, a few thousand MOX fuel rods were successfully irradiated. Though much of this work was performed with weapons-grade or ''near'' weapons-grade plutonium--and favorable fuel performance was observed--the applicability of this data for licensing and use of weapons-grade MOX fuel manufactured with modern fuel fabrication processes is somewhat limited. The U.S. and Russia are currently engaged in an intensive research, development, and demonstration program to support implementation of the MOX option in our two countries. This paper focuses on work performed in the U.S. and provides a brief summary of joint U.S./Russian work currently underway

Reactor-based plutonium disposition: Opportunities, options, and issues

International Nuclear Information System (INIS)

Greene, S.

2000-01-01

The end of the Cold War has created a legacy of surplus fissile materials (plutonium and highly enriched uranium) in the United States (U.S.) and the former Soviet Union. These materials pose a danger to national and international security. During the past few years, the U.S. and Russia have engaged in an ongoing dialog concerning the safe storage and disposition of surplus fissile material stockpiles. In January 1997, the Department of Energy (DOE) announced the U.S. would pursue a dual track approach to rendering approximately 50 metric tons of plutonium inaccessible for use in nuclear weapons. One track involves immobilizing the plutonium by combining it with high-level radioactive waste in glass or ceramic ''logs''. The other method, referred to as reactor-based disposition, converts plutonium into mixed oxide (MOX) fuel for nuclear reactors. The U.S. and Russia are moving ahead rapidly to develop and demonstrate the technology required to implement the MOX option in their respective countries. U.S. MOX fuel research and development activities were started in the 1950s with irradiation of MOX fuel rods in commercial light water reactors (LWR) from the 1960s-1980s. In all, a few thousand MOX fuel rods were successfully irradiated. Though much of this work was performed with weapons-grade or ''near'' weapons-grade plutonium - and favorable fuel performance was observed - the applicability of this data for licensing and use of weapons-grade MOX fuel manufactured with modem fuel fabrication processes is somewhat limited. The U.S. and Russia are currently engaged in an intensive research, development, and demonstration program to support implementation of the MOX option in our two countries. This paper focuses on work performed in the U.S. and provides a brief summary of joint U.S./Russian work currently underway. (author)

DOE plutonium disposition study: Pu consumption in ALWRs

International Nuclear Information System (INIS)

1993-01-01

The Department of Energy (DOE) has contracted with Asea Brown Boveri-Combustion Engineering (ABB-CE) to provide information on the capability of ABB-CE's System 80 + Advanced Light Water Reactor (ALWR) to transform, through reactor burnup, 100 metric tonnes (MT) of weapons grade plutonium (Pu) into a form which is not readily useable in weapons. This information is being developed as part of DOE's Plutonium Disposition Study, initiated by DOE in response to Congressional action. This document Volume 2, provides a discussion of: Plutonium Fuel Cycle; Technology Needs; Regulatory Considerations; Cost and Schedule Estimates; and Deployment Strategy

MIS High-Purity Plutonium Oxide Metal Oxidation Product TS707001 (SSR123): Final Report

Energy Technology Data Exchange (ETDEWEB)

Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Stroud, Mary Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Berg, John M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Narlesky, Joshua Edward [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Worl, Laura Ann [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinez, Max A. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Carillo, Alex [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-08-09

A high-purity plutonium dioxide material from the Material Identification and Surveillance (MIS) Program inventory has been studied with regard to gas generation and corrosion in a storage environment. Sample TS707001 represents process plutonium oxides from several metal oxidation operations as well as impure and scrap plutonium from Hanford that are currently stored in 3013 containers. After calcination to 950°C, the material contained 86.98% plutonium with no major impurities. This study followed over time, the gas pressure of a sample with nominally 0.5 wt% water in a sealed container with an internal volume scaled to 1/500th of the volume of a 3013 container. Gas compositions were measured periodically over a six year period. The maximum observed gas pressure was 138 kPa. The increase over the initial pressure of 80 kPa was primarily due to generation of nitrogen and carbon dioxide gas in the first six months. Hydrogen and oxygen were minor components of the headspace gas. At the completion of the study, the internal components of the sealed container showed signs of corrosion, including pitting.

Plutonium fires; Incendies de plutonium

Energy Technology Data Exchange (ETDEWEB)

Mestre, E.

1959-06-23

The author reports an information survey on accidents which occurred when handling plutonium. He first addresses accidents reported in documents. He indicates the circumstances and consequences of these accidents (explosion in glove boxes, fires of plutonium chips, plutonium fire followed by filter destruction, explosion during plutonium chip dissolution followed by chip fire). He describes hazards associated with plutonium fires: atmosphere and surface contamination, criticality. The author gives some advices to avoid plutonium fires. These advices concern electric installations, the use of flammable solvents, general cautions associated with plutonium handling, venting and filtration. He finally describes how to fight plutonium fires, and measures to be taken after the fire (staff contamination control, atmosphere control)

Risk analysis of fatal and incidental lung tumors in wister rats after inhalation of plutonium dioxide

International Nuclear Information System (INIS)

Kai, M.; Akahane, K.; Ogiso, Y.

2000-01-01

Cancer risk analysis was done in animal studies for inhalation of plutonium dioxide. Female Wister rats were exposed to an aerosol of plutonium with AMAD of 0.4-0.5 μm and followed up until they died. We made some model analyses using their likelihood function. This approach enables us to consider temporal variation in dose-response analysis. Each rat contributes to the total likelihood depending on fatal or incidental tumors. In Weibul model analysis, the logarithm of the hazard function can be linearly modeled with the term of log (dose), log-L model, and additional term of the square of log (dose), log-LQ model. The likelihood ratio statistics gave a significantly better fit of the log-LQ model. However, if data more than 4 Gy were excluded, there was no significant difference between both models. The ratio of hazard function at 1 Gy and 0 Gy, the excess relative risk, showed 30 for total tumors. This result was much different from those in PNL data (Sanders et al.). The difference of pulmonary deposition depending upon particle size would cause different tumor incidence. Our studies indicated significant increase of occurrence of fatal lung cancer at an average dose of 0.5 Gy and thus did not suggest that a life-span effective threshold for death was about 1 Gy to the lung, which is shown in some papers. In contrast PNL, the incidence of adenoma showing the maximum at 0.5 Gy decreased with increasing lung dose from 1.5 Gy or higher, where malignant tumors such as adenocarcinomas increased. This phenomenon was analyzed with carcinogenesis models. (author)

Stop plutonium; Stop plutonium

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-02-01

This press document aims to inform the public on the hazards bound to the plutonium exploitation in France and especially the plutonium transport. The first part is a technical presentation of the plutonium and the MOX (Mixed Oxide Fuel). The second part presents the installation of the plutonium industry in France. The third part is devoted to the plutonium convoys safety. The highlight is done on the problem of the leak of ''secret'' of such transports. (A.L.B.)

Hematological effects of inhaled plutonium dioxide in beagles

International Nuclear Information System (INIS)

Weller, R.E.; Buschbom, R.L.; Park, J.F.

1995-01-01

A life-span study indicated that plutonium activity in the thoracic lymph nodes is a contributor to development of lymphopenia in beagles exposed to 239 PuO 2 . Significant lymphopenia was found in 67 (58%) beagles given a single nose-only exposure to 239 PuO 2 to result in mean initial lung depositions ranging from 0.69 to 213.3 kBq. Lymphoid atrophy and sclerosis of the thoracic lymph nodes and lymphopenia were observed in exposure-level groups with initial lung depositions ≥2.5 kBq. Those dogs with final plutonium concentrations in the thoracic lymph nodes ≥0.4 kBq/g and dose rates ≥0.01 Gy/day developed lymphopenia. Marked differences existed between chronically lymphopenic dogs and intermittently lymphopenic dogs with regard to initial lung deposition, time to lymphopenic events and absolute lymphocyte concentrations. Linear regression analysis revealed moderate correlation between reduction in lymphocyte values and initial lung deposition, in both magnitude and time of appearance after exposure. Cumulative dose and dose rate appeared to act together to produce initial effects on lymphocyte populations, while dose rate alone appeared to be responsible for the maintenance and subsequent cycles of lymphopenia seen over the life span. No primary tumors were associated with the thoracic lymph nodes in this study, although 70% of the lymphopenic dogs developed lung tumors. 28 refs., 2 figs., 7 tabs

Studies of the conversion-chemistry of plutonium and uranium in the nitrate- and carbonate-systems

International Nuclear Information System (INIS)

Hoffmann, G.; Steinhauser, M.; Boehm, M.

1988-01-01

A novel type construction of an autoclave for dissolving of plutonium dioxide in concentrated nitric acid (without any admixtures) has been developed. This process allows the dissolving of batches with high oxide/acid ratio and yields plutonium-solutions of high concentration. The tests for separation of plutonium- and, respectively, uranium-process-solutions from Am-241 and other interfering impurities are described. The time-factor for the oxidation-reaction of plutonium in nitric acid with ozone has been optimized. Important data on the solubility-behavior of plutonyl(VI)- and of pure Pu(IV)-nitrates have been gained. The majority of the precipitates, occuring in theses reactions, were characterized. (orig.) [de

Reactor-grade plutonium inventory taking in the RT-1 storage production association Mayak site

International Nuclear Information System (INIS)

Zatorskij, Yu.M.

1999-01-01

General characterization of plutonium physical inventory taking (PIT) system at the RT-1 plant is given in the paper. The proposed PIT procedure is based on measuring indirect parameters of inventory plutonium, the so called attributes of items - containers with plutonium. The method how to assess quality of item attribute measurements is proposed. If any defect is detected, the container is sent back to the place where it been filed and packed in order to perform direct measurements of plutonium mass. Taking into account the above-mentioned techniques and the availability of several access control means it is proposed the period between two PIT procedures be equal to 12 months [ru

Non-proliferation issues with weapons-usable plutonium

International Nuclear Information System (INIS)

Gray, L.W.

2000-01-01

In this paper author deals with the plutonium produced in power reactors and with their using. Excess plutonium, mineralized in a ceramic matrix and incised in HLW glass, is a less attractive target for terrorist groups than either aged, irradiated weapons grade MOX fuel, or aged, U oxide spent fuel. This is especially true after the Russian and United States' Pu Disposition Programs have been completed, until the material (spent MOX fuel or the immobilized form) is stored in a sealed, repository. (authors)

DOE Plutonium Disposition Study: Pu consumption in ALWRs

International Nuclear Information System (INIS)

1993-01-01

The Department of Energy (DOE) has contracted with Asea Brown Boveri-Combustion Engineering (ABB-CE) to provide information on the capability of ABB-CE's System 80 + Advanced Light Water Reactor (ALWR) to transform, through reactor burnup, 100 metric tonnes (MT) of weapons grade plutonium (Pu) into a form which is not readily useable in weapons. This information is being developed as part of DOE's Plutonium Disposition Study, initiated by DOE in response to Congressional action. This document, Volume 1, presents a technical description of the various elements of the System 80 + Standard Plant Design upon which the Plutonium Disposition Study was based. The System 80 + Standard Design is fully developed and directly suited to meeting the mission objectives for plutonium disposal. The bass U0 2 plant design is discussed here

Modernization of RTC for fabrication of MOX fuel, Vibropac fuel pins and BN-600 FA with weapon grade plutonium

International Nuclear Information System (INIS)

Grachyov, A.F.; Kalygin, V.V.; Skiba, O.V.; Mayorshin, A. A.; Bychkov, A.V.; Kisly, V.A.; Ovsyannikov, Y.F.; Bobrov, D.A.; Mamontov, S.I.; Tsyganov, A.N.; Churutkin, E.I.; Davydov, P.I.; Samosenko, E.A; Shalak, A.R.; Ojima, Hisao

2004-01-01

Since mid 70's RIAR has been performing activities on plutonium involvement in fuel cycle. These activities are considered a stage within the framework of the closed fuel cycle development. Developed at RIAR fuel cycle is based on two technologies: 'dry' process of fuel reprocessing and vibro-packing method for fuel pin fabrication. Due to the available scientific capabilities and a gained experience in operating the technological facilities (ORYOL, SIC) for plutonium (various grade) blending into fuel for fast reactors, RIAR is a participant of the activities aimed at solving these tasks. Under international program RIAR with financial support of JNC (Japan) is modernizing the facility for granulated fuel production, vibro-pac fuel pins and FA fabrication to provide the BN-600 'hybrid' core. In order to provide 'hybrid' core it is necessary to produce (per year): - 1775 kg of granulated MOX-fuel, 6500 fuel pins, 50 fuel assemblies. Potential output of the facility under construction is as follows: - 1800 kg of granulated MOX-fuel per year, 40 fuel pins per shift, 200 FAs for the BN-600 reactor per year. Taking into account domestic and foreign experience in MOX-fuel production, different options were discussed of the equipment layouts in the available premises of chemical technological division of RIAR: - in the shielded manipulator boxes, in the existing hot cells. During construction of the facility in the building under operation the following requirements should be met: - facility must meet all standards and regulations set for nuclear facilities, installation work at the facility must not influence other production programs implemented in the building, engineering supply lines of the facility must be connected to the existing service lines of the building, cost of the activities must not exceed amount of JNC funding. The paper presents results of comparison between two options of the process equipment layout: in boxes and hot cells. This equipment is intended

Materials identification and surveillance project item evaluation: Items, impure plutonium oxide (ATL27960) and pure plutonium oxide (PEOR3258)

International Nuclear Information System (INIS)

Allen, T.; Appert, Q.; Davis, C.

1997-03-01

In this report, Los Alamos scientists characterize properties relevant to storage of an impure plutonium oxide (74 mass % plutonium) in accordance with the Department of Energy (DOE) standard DOE-STD-3013-96. This oxide is of interest because it is the first impure plutonium oxide sample to be evaluated and it is similar to other materials that must be stored. Methods used to characterize the oxide at certain points during calcination include surface-area analyses, mass loss-on-ignition (LOI) measurements, elemental analysis, moisture-adsorption measurements, and quantitative supercritical-CO 2 extraction of adsorbed water. Significant decreases in the LOI and surface area occurred as the oxide was calcined at progressively increasing temperatures. Studies indicate that supercritical-CO 2 extraction is an effective method for removing adsorbed water from oxides. We extracted the water from powdered oxides (high-purity ZrO 2 , pure PuO 2 , and impure plutonium oxide) using CO 2 at 3000 psi pressure and 75 degrees C, and we quantitatively determined it by using gravimetric and dew-point procedures. The effectiveness of the extraction method is demonstrated by good agreement between the amounts of water extracted from pure zirconium and plutonium dioxides and the mass changes obtained from LOI analyses. However, the amount of moisture (0.025 mass %) extracted from the impure plutonium oxide after it had been calcined at 950 degrees C and stored for a period of months is much less than the LOI value (0.97 mass %). These results imply that the impure plutonium oxide is free of adsorbed water after calcination at 950 degrees C, even though the sample does not satisfy the LOI requirement of <0.50 mass % for storage

Weapons-grade nuclear material - open questions of a safe disposal

International Nuclear Information System (INIS)

Closs, K.D.; Giraud, J.P.; Grill, K.D.; Hensing, I.; Hippel, F. von; Holik, J.; Pellaud, B.

1995-01-01

There are suitable technologies available for destruction of weapons-grade uranium and plutonium. Weapons-grade uranium, consisting to 90% of the isotope U-235, can be diluted with the uranium isotope U-238 to make it non-weapons-grade, but it will then still be a material that can be used as a fuel in civil nuclear reactors. For safe plutonium disposal, several options are under debate. There is for instance a process called ''reverse reprocessing'', with the plutonium being blended with high-level radioactive fission products and then being put into a waste form accepted for direct ultimate disposal. The other option is to convert weapons-grade plutonium into MOX nuclear fuel elements and then ''burn'' them in civil nuclear power reactors. This is an option favoured by many experts. Such fuel elements should stay for a long time in the reactor core in order to achieve high burnups, and should then be ready for ultimate disposal. This disposal pathway offers essential advantages: the plutonium is used up or depleted as a component of reactor fuel, and thus is no longer available for illegal activities, and it serves as an energy source for power generation. (orig./HP) [de

Uncertainty assessment in gamma spectrometric measurements of plutonium isotope ratios and age

Energy Technology Data Exchange (ETDEWEB)

Ramebaeck, H., E-mail: henrik.ramebeck@foi.se [Swedish Defence Research Agency, FOI, Division of CBRN Defence and Security, SE-901 82 Umea (Sweden); Chalmers University of Technology, Department of Chemical and Biological Engineering, Nuclear Chemistry, SE-412 96 Goeteborg (Sweden); Nygren, U.; Tovedal, A. [Swedish Defence Research Agency, FOI, Division of CBRN Defence and Security, SE-901 82 Umea (Sweden); Ekberg, C.; Skarnemark, G. [Chalmers University of Technology, Department of Chemical and Biological Engineering, Nuclear Chemistry, SE-412 96 Goeteborg (Sweden)

2012-09-15

A method for the assessment of the combined uncertainty in gamma spectrometric measurements of plutonium composition and age was evaluated. Two materials were measured. Isotope dilution inductively coupled plasma sector field mass spectrometry (ID-ICP-SFMS) was used as a reference method for comparing the results obtained with the gamma spectrometric method for one of the materials. For this material (weapons grade plutonium) the measurement results were in agreement between the two methods for all measurands. Moreover, the combined uncertainty in all isotope ratios considered in this material (R{sub Pu238/Pu239}, R{sub Pu240/Pu239}, R{sub Pu241/Pu239}, and R{sub Am241/Pu241} for age determination) were limited by counting statistics. However, the combined uncertainty for the other material (fuel grade plutonium) were limited by the response fit, which shows that the uncertainty in the response function is important to include in the combined measurement uncertainty of gamma spectrometric measurements of plutonium.

Crystalline matrices for the immobilization of plutonium and actinides

Energy Technology Data Exchange (ETDEWEB)

Anderson, E.B.; Burakov, E.E.; Galkin, Ya.B.; Starchenko, V.A.; Vasiliev, V.G. [V.G. Khlopin Radium Institute, St. Petersburg (Russian Federation)

1996-05-01

The management of weapon plutonium, disengaged as a result of conversion, is considered together with the problem of the actinide fraction of long-lived high level radioactive wastes. It is proposed to use polymineral ceramics based on crystalline host-phases: zircon ZrSiO{sub 4} and zirconium dioxide ZrO{sub 2}, for various variants of the management of plutonium and actinides (including the purposes of long-term safe storage or final disposal from the human activity sphere). It is shown that plutonium and actinides are able to form with these phases on ZrSiO{sub 4} and ZrO{sub 2} was done on laboratory level by the hot pressing method, using the plasmochemical calcination technology. To incorporate simulators of plutonium into the structure of ZrSiO{sub 4} and ZrO{sub 2} in the course of synthesis, an original method developed by the authors as a result of studying the high-uranium zircon (Zr,U) SiO{sub 4} form Chernobyl {open_quotes}lavas{close_quotes} was used.

Safe disposal of surplus plutonium

Science.gov (United States)

Gong, W. L.; Naz, S.; Lutze, W.; Busch, R.; Prinja, A.; Stoll, W.

2001-06-01

About 150 tons of weapons grade and weapons usable plutonium (metal, oxide, and in residues) have been declared surplus in the USA and Russia. Both countries plan to convert the metal and oxide into mixed oxide fuel for nuclear power reactors. Russia has not yet decided what to do with the residues. The US will convert residues into a ceramic, which will then be over-poured with highly radioactive borosilicate glass. The radioactive glass is meant to provide a deterrent to recovery of plutonium, as required by a US standard. Here we show a waste form for plutonium residues, zirconia/boron carbide (ZrO 2/B 4C), with an unprecedented combination of properties: a single, radiation-resistant, and chemically durable phase contains the residues; billion-year-old natural analogs are available; and criticality safety is given under all conceivable disposal conditions. ZrO 2/B 4C can be disposed of directly, without further processing, making it attractive to all countries facing the task of plutonium disposal. The US standard for protection against recovery can be met by disposal of the waste form together with used reactor fuel.

Management of Russian military plutonium

International Nuclear Information System (INIS)

Zaleski, C.P.

1996-01-01

The objective of this paper is to propose and discuss a solution which enables storing as quickly as possible all weapons-grade plutonium from Russian military program in a way which would prevent diversion. Two main conditions apply to this solution. First, it should be achieved in a manner acceptable to Russian government, notably by preserving plutonium for possible future energy production, and second, the economics of the total system should be good enough to ensure no charge or limited charge for the storage of plutonium. A proposal is made to store plutonium in a specially designed fast reactor or specially designed reactor core. This solution could be favorable in comparison to other solutions applying the above mentioned goal and conditions. Additionally the proposed solution would have the following side advantages: utilizing available personnel and installations of the Russian nuclear complex; providing possible basis for decommissioning of older and less safe Russian reactors; giving experience of construction and operation of a series of sodium-cooled fast reactors. The major problem however is the need for large capital investment with the risk of getting no adequate return on investment due to difficult political and economic situation in Russia

Control of civilian plutonium inventories using burning in a non-fertile fuel

Energy Technology Data Exchange (ETDEWEB)

Oversby, V.M. [Lawrence Livermore National Lab., CA (United States); McPheeters, C.C. [Argonne National Laboratory, 9700 South Cass Avenue, Argonne, IL 60439-4837 (United States); Degueldre, C. [Paul Scherrer Institute, 5232 Villigen-PSI (Switzerland); Paratte, J.M. [Paul Scherrer Institute, 5232 Villigen-PSI (Switzerland)

1997-05-01

The increasing inventories of plutonium generated by commercial nuclear power production represent a potential source for proliferation of nuclear weapons. To address this threat we propose separating the plutonium from the other constituents of commercial reactor spent fuel and burning it in a non-fertile fuel based on a zirconium dioxide matrix. The separation can be performed by the Purex process currently in use, but we recommend development of a more compact separation technology that would produce less secondary waste than currently used technology and would allow for more stringent accounting of plutonium inventories. The non-fertile fuel is designed for use in conventional light water power reactors and does not require development of new reactor technology. (orig.).

Control of civilian plutonium inventories using burning in a non-fertile fuel

Science.gov (United States)

Oversby, V. M.; McPheeters, C. C.; Degueldre, C.; Paratte, J. M.

1997-05-01

The increasing inventories of plutonium generated by commercial nuclear power production represent a potential source for proliferation of nuclear weapons. To address this threat we propose separating the plutonium from the other constituents of commercial reactor spent fuel and burning it in a non-fertile fuel based on a zirconium dioxide matrix. The separation can be performed by the Purex process currently in use, but we recommend development of a more compact separation technology that would produce less secondary waste than currently used technology and would allow for more stringent accounting of plutonium inventories. The non-fertile fuel is designed for use in conventional light water power reactors and does not require development of new reactor technology.

Fabrication of mixed oxide fuel using plutonium from dismantled weapons

International Nuclear Information System (INIS)

Blair, H.T.; Chidester, K.; Ramsey, K.B.

1996-01-01

A very brief summary is presented of experimental studies performed to support the use of plutonium from dismantled weapons in fabricating mixed oxide (MOX) fuel for commercial power reactors. Thermal treatment tests were performed on plutonium dioxide powder to determine if an effective dry gallium removal process could be devised. Fabrication tests were performed to determine the effects of various processing parameters on pellet quality. Thermal tests results showed that the final gallium content is highly dependent on the treatment temperature. Fabrication tests showed that the milling process, sintering parameters, and uranium feed did effect pellet properties. 1 ref., 1 tab

Preparation and characterization of PMMA graded microporous foams via one-step supercritical carbon dioxide foaming

International Nuclear Information System (INIS)

Yuan Huan; Li Junguo; Xiong Yuanlu; Luo Guoqiang; Shen Qiang; Zhang Lianmeng

2013-01-01

Supercritical carbon dioxide (ScCO 2 ) foaming which is inexpensive and environmental friendly has been widely used to prepare polymer-based microporous materials. In this paper, PMMA graded microporous materials were foamed by PMMA matrix after an unstable saturation process which was done under supercritical condition of 28MPa and 50 °C. The scanning electron microscopy (SEM) was utilized to observe the morphology of the graded foam. A gas adsorption model was proposed to predict the graded gas concentration in the different region of the polymer matrix. The SEM results showed that the solid and foam region of the graded foam can be connected without laminated layers. With the increasing thickness position of the graded microporous foam, the cell size increased from 3.4 to 27.5 μm, while the cell density decreased from 1.04 × 10 9 to 1.96 × 10 7 cells/cm 3 . It also found that the gradient microporous structure of the foam came from graded gas concentration which was obtained in the initial saturation process.

Vapor pressures and vapor compositions in equilibrium with hypostoichiometric plutonium dioxide at high temperatures

International Nuclear Information System (INIS)

Green, D.W.; Fink, J.K.; Leibowitz, L.

1982-01-01

Vapor pressures and vapor compositions have been calculated for 1500 less than or equal to T less than or equal to 4000 0 K. Thermodynamic functions for the condensed phase and for each of the gaseous species were combined with an oxygen-potential model extended into the liquid region to obtain the partial pressures of O 2 , O, Pu, PuO and PuO 2 . The calculated oxygen pressures increase very rapidly as stoichiometry is approached. At least part of this increase is a consequence of the exclusion of Pu 6 + from the oxygen-potential model. No reliable method was found to estimate the importance of this ion. As a result of large oxygen potentials at high temperatures, extremely high total pressures that produced unreasonably high vapor densities were calculated. The highest temperature was therefore limited to 400 K, and the range of oxygen-to-metal ratios was limited to 1.994 to 1.70. These calculations show that vapor in equilibrium with hypostoichiometric plutonium dioxide is poorly approximated as PuO 2 for most of the temperture and composition range of interest. The vapor is much more oxygen-rich than the condensed phase. Implications for the (U,Pu)O/sub 2-x/ system are discussed

Neutronic analysis of the PBMR-400 full core using thorium fuel mixed with plutonium or minor actinides

International Nuclear Information System (INIS)

Acır, Adem; Coşkun, Hasan

2012-01-01

Highlights: ► Neutronic calculations for PBMR 400 were conducted with the computer codes MCNP and MONTEBURNS 2.0. ► The criticality and burnup were investigated for reactor grade plutonium and minor actinides. ► We found that the use of these new fuels in PBMRs would reduce the nuclear waste repository significantly. -- Abstract: Time evolution of criticality and burnup grades of the PBMR were investigated for reactor grade plutonium and minor actinides in the spent fuel of light water reactors (LWRs) mixed with thoria. The calculations were performed by employing the computer codes MCNP and MONTEBURNS 2.0 and using the ENDF/B-V nuclear data library. Firstly, the plutonium–thorium and minor actinides–thorium ratio was determined by using the initial k eff value of the original uranium fuel design. After the selection of the plutonium/minor actinides–thorium mixture ratio, the time-dependent neutronic behavior of the reactor grade plutonium and minor actinides and original fuels in a PBMR-400 reactor was calculated by using the MCNP code. Finally, k eff , burnup and operation time values of the fuels were compared. The core effective multiplication factor (k eff ) for the original fuel which has 9.6 wt.% enriched uranium was computed as 1.2395. Corresponding to this k eff value the reactor grade plutonium/thorium and minor actinide/thorium oxide mixtures were found to be 30%/70% and 50%/50%, respectively. The core lives for the original, the reactor grade plutonium/thorium and the minor actinide/thorium fuels were calculated as ∼3.2, ∼6.5 and ∼5.5 years, whereas, the corresponding burnups came out to be 99,000, ∼190,000 and ∼166,000 MWD/T, respectively, for an end of life k eff set equal to 1.02.

Fuel qualification issues and strategies for reactor-based surplus plutonium disposition

International Nuclear Information System (INIS)

Cowell, B.S.; Copeland, G.L.; Moses, D.L.

1997-08-01

The Department of Energy (DOE) has proposed irradiation of mixed-oxide (MOX) fuel in existing commercial reactors as a disposition method for surplus plutonium from the weapons program. The burning of MOX fuel in reactors is supported by an extensive technology base; however, the infrastructure required to implement reactor-based plutonium disposition does not exist domestically. This report identifies and examines the actions required to qualify and license weapons-grade (WG) plutonium-based MOX fuels for use in domestic commercial light-water reactors (LWRs)

Transmutation of plutonium in pebble bed type high temperature reactors

International Nuclear Information System (INIS)

Bende, E.E.

1997-01-01

The pebble bed type High Temperature Reactor (HTR) has been studied as a uranium-free burner of reactor grade plutonium. In a parametric study, the plutonium loading per pebble as well as the type and size of the coated particles (CPs) have been varied to determine the plutonium consumption, the final plutonium burnup, the k ∞ and the temperature coefficients as a function of burnup. The plutonium loading per pebble is bounded between 1 and 3 gr Pu per pebble. The upper limit is imposed by the maximal allowable fast fluence for the CPs. A higher plutonium loading requires a longer irradiation time to reach a desired burnup, so that the CPs are exposed to a higher fast fluence. The lower limit is determined by the temperature coefficients, which become less negative with increasing moderator-actinide ratio. A burnup of about 600 MWd/kgHM can be reached. With the HTR's high efficiency of 40%, a plutonium supply of 1520 kg/GW e a is achieved. The discharges of plutonium and minor actinides are then 450 and 110 kg/GW e a, respectively. (author)

Excess plutonium disposition using ALWR technology

International Nuclear Information System (INIS)

Phillips, A.; Buckner, M.R.; Radder, J.A.; Angelos, J.G.; Inhaber, H.

1993-02-01

The Office of Nuclear Energy of the Department of Energy chartered the Plutonium Disposition Task Force in August 1992. The Task Force was created to assess the range of practicable means of disposition of excess weapons-grade plutonium. Within the Task Force, working groups were formed to consider: (1) storage, (2) disposal,and(3) fission options for this disposition,and a separate group to evaluate nonproliferation concerns of each of the alternatives. As a member of the Fission Working Group, the Savannah River Technology Center acted as a sponsor for light water reactor (LWR) technology. The information contained in this report details the submittal that was made to the Fission Working Group of the technical assessment of LWR technology for plutonium disposition. The following aspects were considered: (1) proliferation issues, (2) technical feasibility, (3) technical availability, (4) economics, (5) regulatory issues, and (6) political acceptance

Dry sample storage system for an analytical laboratory supporting plutonium processing

International Nuclear Information System (INIS)

Treibs, H.A.; Hartenstein, S.D.; Griebenow, B.L.; Wade, M.A.

1990-01-01

The Special Isotope Separation (SIS) plant is designed to provide removal of undesirable isotopes in fuel grade plutonium by the atomic vapor laser isotope separation (AVLIS) process. The AVLIS process involves evaporation of plutonium metal, and passage of an intense beam of light from a laser through the plutonium vapor. The laser beam consists of several discrete wavelengths, tuned to the precise wavelength required to ionize the undesired isotopes. These ions are attracted to charged plates, leaving the bulk of the plutonium vapor enriched in the desired isotopes to be collected on a cold plate. Major portions of the process consist of pyrochemical processes, including direct reduction of the plutonium oxide feed material with calcium metal, and aqueous processes for purification of plutonium in residues. The analytical laboratory for the plant is called the Material and Process Control Laboratory (MPCL), and provides for the analysis of solid and liquid process samples

Prospective studies of HTR fuel cycles involving plutonium

International Nuclear Information System (INIS)

Bonin, B.; Greneche, D.; Carre, F.; Damian, F.; Doriath, J.Y.

2002-01-01

High Temperature Gas Cooled reactors (HTRs) are able to accommodate a wide variety of mixtures of fissile and fertile materials without any significant modification of the core design. This flexibility is due to an uncoupling between the parameters of cooling geometry, and the parameters which characterize neutronic optimisation (moderation ratio or heavy nuclide concentration and distribution). Among other advantageous features, an HTR core has a better neutron economy than a LWR because there is much less parasitic capture in the moderator (capture cross section of graphite is 100 times less than the one of water) and in internal structures. Moreover, thanks to the high resistance of the coated particles, HTR fuels are able to reach very high burn-ups, far beyond the possibilities offered by other fuels (except the special case of molten salt reactors). These features make HTRs especially interesting for closing the nuclear fuel cycle and stabilizing the plutonium inventory. A large number of fuel cycle studies are already available today, on 3 main categories of fuel cycles involving HTRs : i) High enriched uranium cycle, based on thorium utilization as a fertile material and HEU as a fissile material; ii) Low enriched uranium cycle, where only LEU is used (from 5% to 12%); iii) Plutonium cycle based on the utilization of plutonium only as a fissile material, with (or without) fertile materials. Plutonium consumption at high burnups in HTRs has already been tested with encouraging results under the DRAGON project and at Peach Bottom. To maximize plutonium consumption, recent core studies have also been performed on plutonium HTR cores, with special emphasis on weapon-grade plutonium consumption. In the following, we complete the picture by a core study for a HTR burning reactor-grade plutonium. Limits in burnup due to core neutronics are investigated for this type of fuel. With these limits in mind, we study in some detail the Pu cycle in the special case of a

CONVERSION OF PLUTONIUM TRIFLUORIDE TO PLUTONIUM TETRAFLUORIDE

Science.gov (United States)

Fried, S.; Davidson, N.R.

1957-09-10

A large proportion of the trifluoride of plutonium can be converted, in the absence of hydrogen fluoride, to the tetrafiuoride of plutonium. This is done by heating plutonium trifluoride with oxygen at temperatures between 250 and 900 deg C. The trifiuoride of plutonium reacts with oxygen to form plutonium tetrafluoride and plutonium oxide, in a ratio of about 3 to 1. In the presence of moisture, plutonium tetrafluoride tends to hydrolyze at elevated temperatures and therefore it is desirable to have the process take place under anhydrous conditions.

Storage of plutonium and nuclear power plant actinide waste in the form of critical-mass-free ceramics containing neutron poisons

Energy Technology Data Exchange (ETDEWEB)

Nadykto, B.A. [RFNC-VNIIEF, Nizhni Novgorod Region (Russian Federation)

2001-07-01

The nuclear weapons production has resulted in accumulation of a large quantity of plutonium and uranium highly enriched with uranium-235 isotope (many tons). The work under ISTC Project 332B-97 treated the issues of safe plutonium storage through making critical-mass-free plutonium oxide compositions with neutron poisons. This completely excludes immediate utilization (without chemical reprocessing) of retained plutonium in nuclear devices. It is therewith possible to locate plutonium most compactly in the storage facility, which would allow reduction in required storage areas and costs. The issues of the surplus weapon-grade plutonium management and utilization have been comprehensively studied in the recent decade. The issues are treated in multiple scientific publications, conferences, and seminars. At the same time, issues of nuclear power engineering actinide waste storage are studied no less extensively. The general issues are material radioactivity and energy release and nuclear accident hazards due to critical mass generation. Plutonium accumulated in nuclear power plant spent fuel is more accessible than weapon-grade plutonium and can become of higher and higher interest with time as its activity reduces, including as material for nuclear devices. The urgency of plutonium management is presently related not only to accumulation of surplus weapon-grade plutonium, but also to the fact that it is high time to decide what has to be done regarding reactor plutonium. Presently, the possibility of actinide separation from NPP spent nuclear fuel and compact underground burial separately from other (mainly fragment) activity is being considered. Actinide and neutron poison base critical-mass-free ceramic materials (similar to plutonium ceramics) may be useful for this burial method. (author)

Storage of plutonium and nuclear power plant actinide waste in the form of critical-mass-free ceramics containing neutron poisons

International Nuclear Information System (INIS)

Nadykto, B.A.

2001-01-01

The nuclear weapons production has resulted in accumulation of a large quantity of plutonium and uranium highly enriched with uranium-235 isotope (many tons). The work under ISTC Project 332B-97 treated the issues of safe plutonium storage through making critical-mass-free plutonium oxide compositions with neutron poisons. This completely excludes immediate utilization (without chemical reprocessing) of retained plutonium in nuclear devices. It is therewith possible to locate plutonium most compactly in the storage facility, which would allow reduction in required storage areas and costs. The issues of the surplus weapon-grade plutonium management and utilization have been comprehensively studied in the recent decade. The issues are treated in multiple scientific publications, conferences, and seminars. At the same time, issues of nuclear power engineering actinide waste storage are studied no less extensively. The general issues are material radioactivity and energy release and nuclear accident hazards due to critical mass generation. Plutonium accumulated in nuclear power plant spent fuel is more accessible than weapon-grade plutonium and can become of higher and higher interest with time as its activity reduces, including as material for nuclear devices. The urgency of plutonium management is presently related not only to accumulation of surplus weapon-grade plutonium, but also to the fact that it is high time to decide what has to be done regarding reactor plutonium. Presently, the possibility of actinide separation from NPP spent nuclear fuel and compact underground burial separately from other (mainly fragment) activity is being considered. Actinide and neutron poison base critical-mass-free ceramic materials (similar to plutonium ceramics) may be useful for this burial method. (author)

Criticality characteristics of mixtures of plutonium, silicon dioxide, Nevada tuff, and water

International Nuclear Information System (INIS)

Sanchez, R.G.; Myers, W.; Stratton, W.

1996-01-01

The major objective of this study has been to examine the possibility of a nuclear explosion should 50 to 100 kg of plutonium be mixed with SiO 2 , vitrified, placed within a heavy steel container, and buried in the material known as Nevada tuff. To accomplish this objective, the authors have created a survey of critical states or configurations of mixtures of plutonium, SiO 2 , tuff, and water and examined these data to determine those configurations that might be unstable or autocatalytic. They have identified regions of criticality instability with the possibility of autocatalytic power behavior. Autocatalytic behavior is possible but improbable, for a very limited range of wet systems

Complementary technologies for verification of excess plutonium

International Nuclear Information System (INIS)

Langner, D.G.; Nicholas, N.J.; Ensslin, N.; Fearey, B.L.; Mitchell, D.J.; Marlow, K.W.; Luke, S.J.; Gosnell, T.B.

1998-01-01

Three complementary measurement technologies have been identified as candidates for use in the verification of excess plutonium of weapons origin. These technologies: high-resolution gamma-ray spectroscopy, neutron multiplicity counting, and low-resolution gamma-ray spectroscopy, are mature, robust technologies. The high-resolution gamma-ray system, Pu-600, uses the 630--670 keV region of the emitted gamma-ray spectrum to determine the ratio of 240 Pu to 239 Pu. It is useful in verifying the presence of plutonium and the presence of weapons-grade plutonium. Neutron multiplicity counting is well suited for verifying that the plutonium is of a safeguardable quantity and is weapons-quality material, as opposed to residue or waste. In addition, multiplicity counting can independently verify the presence of plutonium by virtue of a measured neutron self-multiplication and can detect the presence of non-plutonium neutron sources. The low-resolution gamma-ray spectroscopic technique is a template method that can provide continuity of knowledge that an item that enters the a verification regime remains under the regime. In the initial verification of an item, multiple regions of the measured low-resolution spectrum form a unique, gamma-radiation-based template for the item that can be used for comparison in subsequent verifications. In this paper the authors discuss these technologies as they relate to the different attributes that could be used in a verification regime

Calculation of Doses Due to Accidentally Released Plutonium From An LMFBR

Energy Technology Data Exchange (ETDEWEB)

Fish, B.R.

2001-08-07

Experimental data and analytical models that should be considered in assessing the transport properties of plutonium aerosols following a hypothetical reactor accident have been examined. Behaviors of released airborne materials within the reactor containment systems, as well as in the atmosphere near the reactor site boundaries, have been semiquantitatively predicted from experimental data and analytical models. The fundamental chemistry of plutonium as it may be applied in biological systems has been used to prepare models related to the intake and metabolism of plutonium dioxide, the fuel material of interest. Attempts have been made to calculate the possible doses from plutonium aerosols for a typical analyzed release in order to evaluate the magnitude of the internal exposure hazards that might exist in the vicinity of the reactor after a hypothetical LMFBR (Liquid-Metal Fast Breeder Reactor) accident. Intake of plutonium (using data for {sup 239}Pu as an example) and its distribution in the body were treated parametrically without regard to the details of transport pathways in the environment. To the extent possible, dose-response data and models have been reviewed, and an assessment of their adequacy has been made so that recommended or preferred practices could be developed.

Interactions of Plutonium Dioxide with Water and Oxygen-Hydrogen Mixtures

International Nuclear Information System (INIS)

Haschke, J.M.; Allen, T.H.

1999-01-01

Pressure-volume-temperature data and mass spectrometric results obtained during exposure of PuO 2 to D 2 O show that the dioxide reacts with water at room temperature to produce a higher oxide (PuO 2+x )and H 2 . Results demonstrate that PuO 2+x is the thermodynamically stable oxide in air. The absence of O 2 at detectable levels in the gas phase implies that radiolytic decomposition of water to the elements is not a significant reaction. The rate of the PuO 2 +H 2 O reaction is 6±4 nmol H 2 /m 2 day, a value that is independent of the H 2 O concentration on the oxide over a range that extends from fractional monolayer coverage to saturation by liquid water. Evaluation of literature data shows that oxide compositions in excess of PuO 2.25 are attained, but the maximum value of x is unknown. During exposure of PuO 2 to a 2:1 D 2 :O 2 mixture at room temperature, the elements combine by a process consistent with a surface-catalyzed reaction. Water is simultaneously formed by the H 2 +O 2 reaction and consumed by the PuO 2 + H 2 O reaction and accumulates until the opposing rates are equal. Thereafter, PuO 2+x is formed at a constant rate by the water-catalyzed PuO 2 + O 2 reaction. The failure of earlier attempts to prepare higher oxides of plutonium is discussed and the catalytic cycle that promotes the reaction of PuO 2 with O 2 is described. Implications of the results for extended storage and environmental chemistry of oxide are examined. Moisture-catalyzed oxidation of PuO 2 accounts for observation of both pressure increases and decreases in oxide storage containers with air atmospheres. Application of the experimental rate results indicates that the reaction of a typical oxide with 0.5 mass % of adsorbed water maybe complete after 25 to 50 years at room temperature

Plutonium dioxide dissolution in glass

International Nuclear Information System (INIS)

Vienna, J.D.; Alexander, D.L.; Li, Hong

1996-09-01

In the aftermath of the Cold War, the U.S. Department of Energy's (DOE) Office of Fissile Materials Disposition (OFMD) is charged with providing technical support for evaluation of disposition options for excess fissile materials manufactured for the nation's defense. One option being considered for the disposition of excess plutonium (Pu) is immobilization by vitrification. The vitrification option entails immobilizing Pu in a host glass and waste package that are criticality-safe (immune to nuclear criticality), proliferation-resistant, and environmentally acceptable for long-term storage or disposal. To prove the technical and economic feasibility of candidate vitrification options it is necessary to demonstrate that PuO 2 feedstock can be dissolved in glass in sufficient quantity. The OFMD immobilization program has set a Pu solubility goal of 10 wt% in glass. The life cycle cost of the vitrification options are strongly influenced by the rate at which PUO 2 dissolves in glass. The total number of process lines needed for vitrification of 50 t of Pu in 10 years is directly dependent upon the time required for Pu dissolution in glass. The objective of this joint Pacific Northwest National Laboratory (PNNL) - Savannah River Technology Center (SRTC) study was to demonstrate a high Pu solubility in glass and to identify on a rough scale the time required for Pu dissolution in the glass. This study was conducted using a lanthanide borosilicate (LaBS) glass composition designed at the SRTC for the vitrification of actinides

Plutonium dioxide dissolution in glass

Energy Technology Data Exchange (ETDEWEB)

Vienna, J.D.; Alexander, D.L.; Li, Hong [and others

1996-09-01

In the aftermath of the Cold War, the U.S. Department of Energy`s (DOE) Office of Fissile Materials Disposition (OFMD) is charged with providing technical support for evaluation of disposition options for excess fissile materials manufactured for the nation`s defense. One option being considered for the disposition of excess plutonium (Pu) is immobilization by vitrification. The vitrification option entails immobilizing Pu in a host glass and waste package that are criticality-safe (immune to nuclear criticality), proliferation-resistant, and environmentally acceptable for long-term storage or disposal. To prove the technical and economic feasibility of candidate vitrification options it is necessary to demonstrate that PuO{sub 2} feedstock can be dissolved in glass in sufficient quantity. The OFMD immobilization program has set a Pu solubility goal of 10 wt% in glass. The life cycle cost of the vitrification options are strongly influenced by the rate at which PUO{sub 2} dissolves in glass. The total number of process lines needed for vitrification of 50 t of Pu in 10 years is directly dependent upon the time required for Pu dissolution in glass. The objective of this joint Pacific Northwest National Laboratory (PNNL) - Savannah River Technology Center (SRTC) study was to demonstrate a high Pu solubility in glass and to identify on a rough scale the time required for Pu dissolution in the glass. This study was conducted using a lanthanide borosilicate (LaBS) glass composition designed at the SRTC for the vitrification of actinides.

Plutonium Immobilization Project - Robotic canister loading

International Nuclear Information System (INIS)

Hamilton, R.L.

2000-01-01

The Plutonium Immobilization Program (PIP) is a joint venture between the Savannah River Site (SRS), Lawrence Livermore National Laboratory (LLNL), Argonne National Laboratory (ANL), and Pacific Northwest National Laboratory (PNNL). When operational in 2008, the PIP will fulfill the nation's nonproliferation commitment by placing surplus weapons-grade plutonium in a permanently stable ceramic form and making it unattractive for reuse. Since there are significant radiation and security concerns, the program team is developing novel and unique technology to remotely perform plutonium immobilization tasks. The remote task covered in this paper employs a jointed arm robot to load seven 3.5 inch diameter, 135-pound cylinders (magazines) through the 4 inch diameter neck of a stainless steel canister. Working through the narrow canister neck, the robot secures the magazines into a specially designed rack pre-installed in the canister. To provide the deterrent effect, the canisters are filled with a mixture of high-level waste and glass at the Defense Waste Processing Facility (DWPF)

Characterization of food-grade titanium dioxide: the presence of nanosized particles.

Science.gov (United States)

Yang, Yu; Doudrick, Kyle; Bi, Xiangyu; Hristovski, Kiril; Herckes, Pierre; Westerhoff, Paul; Kaegi, Ralf

2014-06-03

Titanium dioxide (TiO2) is widely used in food products, which will eventually enter wastewater treatment plants and terrestrial or aquatic environments, yet little is known about the fraction of this TiO2 that is nanoscale, or the physical and chemical properties of TiO2 that influence its human and environmental fate or toxicity. Instead of analyzing TiO2 properties in complex food or environmental samples, we procured samples of food-grade TiO2 obtained from global food suppliers and then, using spectroscopic and other analytical techniques, quantified several parameters (elemental composition, crystal structure, size, and surface composition) that are reported to influence environmental fate and toxicity. Another sample of nano-TiO2 that is generally sold for catalytic applications (P25) and widely used in toxicity studies, was analyzed for comparison. Food-grade and P25 TiO2 are engineered products, frequently synthesized from purified titanium precursors, and not milled from bulk scale minerals. Nanosized materials were present in all of the food-grade TiO2 samples, and transmission electron microscopy showed that samples 1-5 contained 35, 23, 21, 17, and 19% of nanosized primary particles (average hydrodynamic diameter of >100 nm. Food-grade samples contained phosphorus (P), with concentrations ranging from 0.5 to 1.8 mg of P/g of TiO2. The phosphorus content of P25 was below inductively coupled plasma mass spectrometry detection limits. Presumably because of a P-based coating detected by X-ray photoelectron spectroscopy, the ζ potential of the food-grade TiO2 suspension in deionized water ranged from -10 to -45 mV around pH 7, and the iso-electric point for food-grade TiO2 (grade materials, and although the presence of amorphous TiO2 could not be ruled out, it is unlikely on the basis of Raman analysis. The food-grade TiO2 was solar photoactive. Cationic dyes adsorbed more readily to food-grade TiO2 than P25, indicating very different potentials for

Life-span studies of inhaled plutonium in beagle dogs

International Nuclear Information System (INIS)

Bair, W.J.

1990-04-01

In 1970 a life-span study with over 300 beagle dogs was begun to gain an understanding of long-term health effects resulting from respiratory tract intakes of plutonium and to derive risk estimates that might be applied to plutonium and other transuranic elements. Groups of beagle dogs were given single exposures to 239 PuO 2 , 238 PuO 2 , or 239 Pu(NO 3 ) 4 to obtain graded levels of initial lung burdens ranging from 1 to 1800 Bq lung. The objective of this paper is to give you a progress report on the current life-span studies of inhaled plutonium in beagle dogs at the Pacific Northwest Laboratory. I will describe the biokinetics of inhaled plutonium in dogs and the resulting health effects. I will also mention some studies directed towards understanding the mechanism leading to these effects. Finally, I will discuss the current risk estimates derived from these studies and how they might relate to plutonium exposures in humans. 5 refs., 13 figs., 4 tabs

Production and industrial applications of plutonium

International Nuclear Information System (INIS)

Lafontaine, I.

1975-01-01

In the present document, an evaluation is made of the quantities of plutonium which will be produced by all nuclear power stations until 1980 and of the plants which are actually able to treat burned nuclear fuels with a view to recover this material. As soon as the plutonium, in the form of dioxide, becomes available, it is transported towards fuel rod and fuel assembly fabrication plants, in containers especially commissioned by the competent authorities; these containers have to resist succesfully to very severe tests specified by the International Atomic Energy Agency in Vienna. Additional protections are foreseen during transportation, namely to prevent an attempt of nuclear materials' diversion. The plant for fabrication of nuclear fuels is designed on the basis of extensive safety studies. Indeed, various probabilities of accidents and associated risks have been evaluated and have given rise namely to safe working rules and the provision of elements of protection [fr

Experiences of shipper-receiver differences in plutonium oxide transactions

International Nuclear Information System (INIS)

Swinburn, K.A.; McGowan, I.R.

1976-01-01

Plutonium oxide has the property of absorbing moisture, carbon dioxide etc., to the extent that it is necessary to take special steps to determine the plutonium content in such a way as to avoid shipper-receiver differences. This paper describes a method used internationally for several years for correcting for any absorption. The consignee witnesses the weighing of the bulk material (D kg) at the time of blending and sampling at the consignor's Works, and also the weighing of the sample (C g). Immediately before analysis the sample is reweighed (B g) and assayed for plutonium (A%). The weight of plutonium is then (A/100)x(B/C)xD kg. The accepted weight is the average between consignor's and consignee's figures after both have used the formula indicated. It goes on to give actual assay and fissile content figures obtained by BNFL and its consignees for the international transactions already referred to, and concludes that the method of approach results cumulatively in a negligible shipper-receiver difference. Individual transactions are shown to be commercially acceptable and, it is considered, also acceptable for safeguards purposes. It is suggested that for safeguarded material the safeguards inspectors might also be able to be present at, and themselves witness, the blending, sampling and weighing operations, and at the same time take their own samples for analysis. It is further suggested that the principle could be extended to accoutancy for plutonium in plutonium nitrate solutions provided leakage does not occur from the sample vials. (author)

How much plutonium does North Korea really have?

International Nuclear Information System (INIS)

Dreicer, J.S.

1997-01-01

In a previous study, as part of the Global Nuclear Material Control Model effort, the author estimated the maximum quantity of plutonium that could be produced in thermal research reactors in the potential nuclear weapon states (including North Korea), based on their declared power level. D. Albright has estimated the amount of plutonium the North Koreans may have produced since 1986 in the 5-megawatt-electric power reactor at Yongbon. Albright provided an upper-bound estimate of 53 kilograms of weapon-grade plutonium produced cumulatively if the gas-graphite (magnox) reactor had achieved a load factor of 0.80. This cumulative estimate of 53 kilograms ignores the potential plutonium production in the 8-megawatt-thermal research reactor, IRT-DPRK. To better quantify the cumulative North Korean production, the author conducted a study to estimate the amount of plutonium that could have been produced in the IRT-DPRK research reactor operating at the declared power level during the entire period it has operated, including a period it was not safeguarded. The author estimates that, at most, an additional 6 to 33 kilograms of plutonium could have been produced cumulatively in the research reactor operating at the declared power level during the entire period it has operated, including a 12-year period it was not safeguarded, resulting in a total of 13 to 47 kilograms of plutonium possibly produced in both the research and power reactors

A perspective on safeguarding and monitoring of excess military plutonium

International Nuclear Information System (INIS)

Sutcliffe, W.G.

1994-01-01

The purpose of this paper is to provide a perspective and framework for the development of safeguarding and monitoring procedures for the various stages of disposition of excess military plutonium. The paper briefly outlines and comments on some of the issues involved in safeguarding and monitoring excess military plutonium as it progresses from weapons through dismantlement, to fabrication as reactor fuel, to use in a reactor, and finally to storage and disposal as spent fuel. open-quotes Militaryclose quotes refers to ownership, and includes both reactor-grade and weapon-grade plutonium. open-quotes Excessclose quotes refers to plutonium (in any form) that a government decides is no longer needed for military use and can be irrevocably removed from military stockpiles. Many of the issues and proposals presented in this paper are based on, or are similar to, those mentioned in the National Academy of Sciences (NAS) report on excess military plutonium. Safeguards for plutonium disposition are discussed elsewhere in terms of requirements established by the U.S. Department of Energy (DOE), the U.S. Nuclear Regulatory Commission (NRC), and the International Atomic Energy Agency (IAEA). Here, the discussion is less specific. The term open-quotes safeguardingclose quotes is used broadly to refer to materials control and accountancy (MC ampersand A), containment and surveillance (C ampersand S), and physical protection of nuclear materials by the state that possesses those materials. This is also referred to as material protection, control, and accountancy (MPCA). The term open-quotes safeguardingclose quotes was chosen for brevity and to distinguish MPCA considered in this paper from international or IAEA safeguards. open-quotes Monitoringclose quotes is used to refer to activities designed to assure another party (state or international organization) that the nuclear materials of the host state (the United States or Russia) are secure and not subject to unauthorized

Potential hydrogen and oxygen partial pressures in legacy plutonium oxide packages at Oak Ridge

Energy Technology Data Exchange (ETDEWEB)

Veirs, Douglas K. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-07-07

An approach to estimate the maximum hydrogen and oxygen partial pressures within sealed containers is described and applied to a set of packages containing high-purity plutonium dioxide. The approach uses experimentally determined maximum hydrogen and oxygen partial pressures and scales the experimentally determined pressures to the relevant packaged material properties. The important material properties are the specific wattage and specific surface area (SSA). Important results from the experimental determination of maximum partial pressures are (1) the ratio of hydrogen to oxygen is stoichiometric, and (2) the maximum pressures increase with increasing initial rates of production. The material properties that influence the rates are the material specific wattage and the SSA. The unusual properties of these materials, high specific wattage and high SSA, result in higher predicted maximum pressures than typical plutonium dioxide in storage. The pressures are well within the deflagration range for mixtures of hydrogen and oxygen.

Plutonium in nature; Le plutonium dans la nature

Energy Technology Data Exchange (ETDEWEB)

Madic, C.

1994-12-31

Plutonium in nature comes from natural sources and anthropogenic ones. Plutonium at the earth surface comes principally from anthropogenic sources. It is easily detectable in environment. The plutonium behaviour in environment is complex. It seems necessary for the future to reduce releases in environment, to improve predictive models of plutonium behaviour in geosphere, to precise biological impact of anthropogenic plutonium releases.

DOE plutonium disposition study: Pu consumption in ALWRs. Volume 2, Final report

Energy Technology Data Exchange (ETDEWEB)

1993-05-15

The Department of Energy (DOE) has contracted with Asea Brown Boveri-Combustion Engineering (ABB-CE) to provide information on the capability of ABB-CE`s System 80 + Advanced Light Water Reactor (ALWR) to transform, through reactor burnup, 100 metric tonnes (MT) of weapons grade plutonium (Pu) into a form which is not readily useable in weapons. This information is being developed as part of DOE`s Plutonium Disposition Study, initiated by DOE in response to Congressional action. This document Volume 2, provides a discussion of: Plutonium Fuel Cycle; Technology Needs; Regulatory Considerations; Cost and Schedule Estimates; and Deployment Strategy.

Peaceful uses of nuclear weapon plutonium; Friedliche Verwertung von Plutonium aus Kernwaffen

Energy Technology Data Exchange (ETDEWEB)

Burtak, F. [Siemens AG Bereich Energieerzeugung (KWU), Erlangen (Germany)

1996-06-01

In 1993, the U.S.A. and the CIS signed Start 2 (the Strategic Arms Reduction Treaty) in which they committed themselves the reduce their nuclear weapon arsenals to a fraction of that of 1991. For forty-five years the antagonism between the superpowers had been a dominating factor in world history, determining large areas of social life. When Start 2 will have been completed in 2003, some 200 t of weapon grade plutonium and some 2000 t of highly enriched uranium (Heu) will arise from dismantling nuclear weapons. In the absence of the ideological ballast of the debate about Communism versus Capitalism of the past few decades there is a chance of the grave worldwide problem of safe disposal and utilization of this former nuclear weapon material being solved. Under the heading of `swords turned into plowshares`, plutonium and uranium could be used for peaceful electricity generation. (orig.) [Deutsch] 1993 unterzeichneten die USA und GUS das Start-2-Abkommen (Strategic Arms Reduction Treaty), in dem sie sich zur Verringerung der Anzahl ihrer Nuklearwaffen auf einen Bruchteil des Bestandes von 1991 verpflichten. 45 Jahre lang stellte die Auseinandersetzung der Supermaechte einen dominierenden Faktor der Weltpolitik dar und bestimmte weite Teile des gesellschaftlichen Lebens. Mit der geplanten Erfuellung von Start 2 im Jahr 2003 werden ca. 200 t waffengraediges Plutonium und ca. 2000 t highly enriched uranium (Heu) aus der Demontage der Kernwaffen anfallen. Ohne den ideologischen Ballast der vergangenen jahrezehntelangen Auseinandersetzung zwischen `Kommunismus` und `Kapitalismus` besteht die Chance, das gravierende weltweite Problem der sicheren Entsorgung und Verwertung dieses ehemaligen Kernwaffenmaterials zu loesen. Unter dem Motto `Schwerter zu Pflugscharen` koennte das Plutonium und Uran zur friedlichen Elektrizitaetserzeugung genutzt werden. (orig.)

Molecular dynamics study of a nuclear waste glass matrix with plutonium

International Nuclear Information System (INIS)

Meis, C.; Delaye, J.M.; Ghaleb, D.

1999-01-01

Molecular dynamics simulation techniques were applied to model the incorporation of plutonium in the French nuclear waste glass matrix. Born-Mayer-Huggins analytical potentials were established to characterize short-range interactions between Pu-O and Pu-Pu pairs; the potentials were fitted to the structural properties of plutonium dioxide in the light of a recent experimental study showing that plutonium is found as Pu(IV) in the glass. The transferability of the established potentials to the glass structure is discussed, and the potential parameters are further refined by molecular dynamics simulations in an aluminoborosilicate glass to obtain mean Pu-O interatomic distances and first-neighbor coordination numbers matching the experimental values as closely as possible. Previously published Born-Mayer-Huggins potentials supplemented by Stillinger-Weber three-body terms were used for oxygen-cation and cation-cation interactions. The difficulties encountered in establishing a Pu-O potential that provides satisfactory results in both oxides and glasses are also discussed

Cost-benefit analysis of unfired PuO2 pellets as an alternative plutonium shipping form

International Nuclear Information System (INIS)

Mishima, J.; Brackenbush, L.W.; Libby, R.A.; Soldat, K.L.; White, G.D.

1983-10-01

A limited cost-benefit evaluation was performed concerning use of unfired plutonium dioxide pellets as a shipping form. Two specific processing operations are required for this use, one to form the pellet (pelletizing) and a second to reconstitute an acceptable powder upon receipt (reconstitution). The direct costs for the pelletizing operation are approximately $208,000 for equipment and its installation and $122 per kg of plutonium processed (based upon a 20-kg plutonium/day facility). The direct costs for reconstitution are approximately $90,000 for equipment and its installation and $81 per kg of plutonium processed. The indirect cost considered was personnel exposure from these operations. Whole body exposures ranged from 0.04 man-rem per 100 kg of low-exposure plutonium reconstituted to 0.9 man-rem per 100 kg of average-exposure plutonium pelletized. Hand exposures were much higher - 17 man-rem power 100 kg of low-exposure plutonium reconstituted to 67 man-rem per 100 kg of average plutonium pelletized. The principal benefit is a potential twentyfold reduction of airborne release in the event of an accident. An experimental plan is outlined to fill the data gaps uncovered during this study in the areas of pelletizing and reconstitution process parameters and pellet response behavior to accident-generated stresses. A study to enhance the containment potential of the inner packaging used during shipment is also outlined

Design safety features of containments used for handling plutonium in Reprocessing Plants

International Nuclear Information System (INIS)

Aherwal, P.; Achuthan, P.V.

2016-01-01

The plutonium present in spent fuel is separated from the associated uranium and fission products using solvent extraction cycles in process cells. Product plutonium nitrate solution containing trace concentrations of uranium and fission products is treated in the reconversion facility through a precipitation-calcination route and converted to sinterable grade plutonium oxide (PuO 2 ). All chemical operations involving materials with high plutonium content, both in solid and solution forms are carried out in glove boxes. Glove box provides an effective isolation from radioactive materials handled and acts as a barrier between the operator and the source of radiation. These glove boxes are interconnected for sequential operations and the interconnected glove box trains are installed within secondary enclosures called double skin which provides double barrier protection to operators

Plutonium

International Nuclear Information System (INIS)

Watson, G.M.

1976-01-01

Discovery of the neutron made it easy to create elements which do not exist in nature. One of these is plutonium, and its isotope with mass number 239 has nuclear properties which make it both a good fuel for nuclear power reactors and a good explosive for nuclear weapons. Since it was discovered during a war the latter characteristic was put to use, but it is now evident that use of plutonium in a particular kind of nuclear reactor, the fast breeder reactor, will allow the world's resources of uranium to last for millennia as a major source of energy. Plutonium is very radiotoxic, resembling radium in this respect. Therefore the widespread introduction of fast breeder reactors to meet energy demands can be contemplated only after assurances on two points; that adequate control of the radiological hazard resulting from the handling of very large amounts of plutonium can be guaranteed, and that diversion of plutonium to illicit use can be prevented. The problems exist to a lesser degree already, since all types of nuclear reactor produce some plutonium. Some plutonium has already been dispersed in the environment, the bulk of it from atmospheric tests of nuclear weapons. (author)

Chemical, mass spectrometric, spectrochemical, nuclear, and radiochemical analysis of nuclear-grade plutonium nitrate solutions

International Nuclear Information System (INIS)

Anon.

1981-01-01

These analytical procedures are designed to show whether a given material meets the purchaser's specifications as to plutonium content, effective fissile content, and impurity content. The following procedures are described in detail: plutonium by controlled-potential coulometry; plutonium by amperometric titration with iron(II); free acid by titration in an oxalate solution; free acid by iodate precipitation-potentiometric titration method; uranium by Arsenazo I spectrophotometric method; thorium by thorin spectrophotometric method; iron by 1,10-phenanthroline spectrophotometric method; chloride by thiocyanate spectrophotometric method; fluoride by distillation-spectrophotometric method; sulfate by barium sulfate turbidimetric method; isotopic composition by mass spectrometry; americium-241 by extraction and gamma counting; americium-241 by gamma counting; gamma-emitting fission products, uranium, and thorium by gamma-ray spectroscopy; rare earths by copper spark spectrochemical method; tungsten, niobium (columbium), and tantalum by spectrochemical method; simple preparation by spectrographic analysis for general impurities

Profileration-proof uranium/plutonium and thorium/uranium fuel cycles. Safeguards and non-profileration. 2. rev. ed.

Energy Technology Data Exchange (ETDEWEB)

Kessler, G.

2017-07-01

A brief outline of the historical development of the proliferation problem is followed by a description of the uranium-plutonium nuclear fuel cycle with uranium enrichment, fuel fabrication, the light-water reactors mainly in operation, and the breeder reactors still under development. The next item discussed is reprocessing of spent fuel with plutonium recycling and the future possibility to incinerate plutonium and the minor actinides: neptunium, americium, and curium. Much attention is devoted to the technical and scientific treatment of the IAEA surveillance concept of the uranium-plutonium fuel cycle. In this context, especially the physically possible accuracy of measuring U/Pu flow in the fuel cycle, and the criticism expressed of the accuracy in measuring the plutonium balance in large reprocessing plants of non-nuclear weapon states are analyzed. The second part of the book initially examines the assertion that reactor-grade plutonium could be used to build nuclear weapons whose explosive yield cannot be predicted accurately, but whose minimum explosive yield is still far above that of chemical explosive charges. Methods employed in reactor physics are used to show that such hypothetical nuclear explosive devices (HNEDs) would attain too high temperatures in the required implosion lenses as a result of the heat generated by the Pu-238 isotope always present in reactor plutonium of current light-water reactors. These lenses would either melt or tend to undergo chemical auto-explosion. Limits to the content of the Pu-238 isotope are determined above which such hypothetical nuclear weapons are not feasible on technical grounds. This situation is analyzed for various possibilities of the technical state of the art of making implosion lenses and various ways of cooling up to the use of liquid helium. The outcome is that, depending on the existing state of the art, reactor-grade plutonium from spent fuel elements of light-water reactors with a burnup of 35 to 58

Plutonium Immobilization Project - Can-In-Canister Hardware Development/Selection

International Nuclear Information System (INIS)

Hamilton, L.

2001-01-01

The Plutonium Immobilization Project (PIP) is a program funded by the U.S. Department of Energy to develop technology to disposition excess weapons grade plutonium. This program introduces the ''Can-in-Canister'' (CIC) technology that immobilizes the plutonium by encapsulating it in ceramic forms (or pucks) and ultimately surrounding it with high-level waste glass to provide a deterrent to recovery. Since there are significant radiation, contamination and security concerns, the project team is developing unique technologies to remotely perform plutonium immobilization tasks. This paper covers the design, development and testing of the magazines (cylinders containing cans of ceramic pucks) and the rack that holds them in place inside the waste glass canister. Several magazine and rack concepts were evaluated to produce a design that gives the optimal balance between resistance to thermal degradation and facilitation of remote handling. This paper also reviews the effort to develop a jointed arm robot that can remotely load seven magazines into defined locations inside a stationary canister working only through the 4 inch (102 mm) diameter canister throat

Plutonium Immobilization Project - Can-In-Canister Hardware Development/Selection

International Nuclear Information System (INIS)

Hamilton, L.

2001-01-01

The Plutonium Immobilization Project (PIP) is a program funded by the U.S. Department of Energy to develop technology to disposition excess weapons grade plutonium. This program introduces the ''Can-in-Canister'' (CIC) technology that immobilizes the plutonium by encapsulating it in ceramic forms (or pucks) and ultimately surrounding it with high-level waste glass to provide a deterrent to recovery. Since there are significant radiation, contamination and security concerns, the project team is developing unique technologies to remotely perform plutonium immobilization tasks. This paper covers the design, development and testing of the magazines (cylinders containing cans of ceramic pucks) and the rack that holds them in place inside the waste glass canister. Several magazine and rack concepts were evaluated to produce a design that gives the optimal balance between resistance to thermal degradation and facilitation of remote handling. This paper also reviews the effort to develop a join ted arm robot that can remotely load seven magazines into defined locations inside a stationary canister working only through the 4 inch (102 mm) diameter canister throat

Plutonium Finishing Plant. Interim plutonium stabilization engineering study

Energy Technology Data Exchange (ETDEWEB)

Sevigny, G.J.; Gallucci, R.H.; Garrett, S.M.K.; Geeting, J.G.H.; Goheen, R.S.; Molton, P.M.; Templeton, K.J.; Villegas, A.J. [Pacific Northwest Lab., Richland, WA (United States); Nass, R. [Nuclear Fuel Services, Inc. (United States)

1995-08-01

This report provides the results of an engineering study that evaluated the available technologies for stabilizing the plutonium stored at the Plutonium Finishing Plant located at the hanford Site in southeastern Washington. Further processing of the plutonium may be required to prepare the plutonium for interim (<50 years) storage. Specifically this document provides the current plutonium inventory and characterization, the initial screening process, and the process descriptions and flowsheets of the technologies that passed the initial screening. The conclusions and recommendations also are provided. The information contained in this report will be used to assist in the preparation of the environmental impact statement and to help decision makers determine which is the preferred technology to process the plutonium for interim storage.

Plutonium Finishing Plant. Interim plutonium stabilization engineering study

International Nuclear Information System (INIS)

Sevigny, G.J.; Gallucci, R.H.; Garrett, S.M.K.; Geeting, J.G.H.; Goheen, R.S.; Molton, P.M.; Templeton, K.J.; Villegas, A.J.; Nass, R.

1995-08-01

This report provides the results of an engineering study that evaluated the available technologies for stabilizing the plutonium stored at the Plutonium Finishing Plant located at the hanford Site in southeastern Washington. Further processing of the plutonium may be required to prepare the plutonium for interim (<50 years) storage. Specifically this document provides the current plutonium inventory and characterization, the initial screening process, and the process descriptions and flowsheets of the technologies that passed the initial screening. The conclusions and recommendations also are provided. The information contained in this report will be used to assist in the preparation of the environmental impact statement and to help decision makers determine which is the preferred technology to process the plutonium for interim storage

Stop plutonium

International Nuclear Information System (INIS)

2003-02-01

This press document aims to inform the public on the hazards bound to the plutonium exploitation in France and especially the plutonium transport. The first part is a technical presentation of the plutonium and the MOX (Mixed Oxide Fuel). The second part presents the installation of the plutonium industry in France. The third part is devoted to the plutonium convoys safety. The highlight is done on the problem of the leak of ''secret'' of such transports. (A.L.B.)

Plutonium disposition study phase 1b final report

International Nuclear Information System (INIS)

1993-01-01

This report provides the results of the Westinghouse activities performed as part of the Plutonium Disposition Study Phase 1b. These activities, which took place from May 16, 1993 to September 15, 1993, build upon the work completed in Phase 1a, which concluded on May 15, 1993. In Phase 1a, three Plutonium Disposal Reactor (PDR) options were developed for the disposal of excess weapons grade plutonium from returned and dismantled nuclear weapons. This report documents the results of several tasks that were performed to further knowledge in specific areas leading up to Phase 2 of the PDR Study. The Westinghouse activities for Phase 1b are summarized as follows: (1) resolved technical issues concerning reactor physics including equilibrium cycle calculations, use of gadolinium, moderator temperature coefficient, and others as documented in Section 2.0; (2) analyzed large Westinghouse commercial plants for plutonium disposal; (3) reactor safety issues including the steam line break were resolved, and are included in Section 2.0; (4) several tasks related to the PDR Fuel Cycle were examined; (5) cost and deployment options were examined to determine optimal configuration for both plutonium disposal and tritium production; (6) response to questions from DOE and National Academy of Scientists (NAS) reviewers concerning the PDR Phase 1a report are included in Appendix A

IFR starts to burn up weapons-grade material

International Nuclear Information System (INIS)

Anon.

1994-01-01

With funding from different parts of the federal government, the Integral Fast Reactor (IFR) project has survived into fiscal year 1994 and is now embarking on a demonstration of how this type of liquid-metal-cooled reactor (LMR) can be used to burn fuel derived from weapons-grade plutonium. This month, an assembly made from weapons-grade material is to be loaded into Experimental Breeder Reactor-II in Idaho, which is serving as the prototype for the IFR concept. Although FY 1994 work is being funded by the DOE, this particular examination of plutonium burnup is backed by the Department of Defense

Characterizing Surplus US Plutonium for Disposition - 13199

Energy Technology Data Exchange (ETDEWEB)

Allender, Jeffrey S. [Savannah River National Laboratory, Aiken SC 29808 (United States); Moore, Edwin N. [Moore Nuclear Energy, LLC, Savannah River Site, Aiken SC 29808 (United States)

2013-07-01

The United States (US) has identified 61.5 metric tons (MT) of plutonium that is permanently excess to use in nuclear weapons programs, including 47.2 MT of weapons-grade plutonium. Surplus inventories will be stored safely by the Department of Energy (DOE) and then transferred to facilities that will prepare the plutonium for permanent disposition. The Savannah River National Laboratory (SRNL) operates a Feed Characterization program for the Office of Fissile Materials Disposition (OFMD) of the National Nuclear Security Administration (NNSA) and the DOE Office of Environmental Management (DOE-EM). SRNL manages a broad program of item tracking through process history, laboratory analysis, and non-destructive assay. A combination of analytical techniques allows SRNL to predict the isotopic and chemical properties that qualify materials for disposition through the Mixed Oxide (MOX) Fuel Fabrication Facility (MFFF). The research also defines properties that are important for other disposition paths, including disposal to the Waste Isolation Pilot Plant (WIPP) as transuranic waste (TRUW) or to high-level waste (HLW) systems. (authors)

Recycling of plutonium and uranium in water reactor fuel. Proceedings of a technical committee meeting

International Nuclear Information System (INIS)

1997-05-01

The Technical Committee Meeting on Recycling of Plutonium and Uranium in Water Reactor Fuel was recommended by the International Working Group on Fuel Performance and Technology (IWGFPT). Its aim was to obtain an overall picture of MOX fabrication capacity and technology, actual performance of this kind of fuel, and ways explored to dispose of the weapons grade plutonium. The subject of this meeting had been reviewed by the International Atomic Energy Agency every 5 to 6 years and for the first time the problem of weapons grade plutonium disposal was included. The papers presented provide a summary of experience on MOX fuel and ongoing research in this field in the participating countries. The meeting was hosted by British Nuclear Fuels plc, at Newby Bridge, United Kingdom, from 3 to 7 July 1995. Fifty-six participants from twelve countries or international organizations took part. Refs, figs, tabs

Advanced PWR Core Design with Siemens High-Plutonium-Content MOX Fuel Assemblies

International Nuclear Information System (INIS)

Dieter Porsch; Gerhard Schlosser; Hans-Dieter Berger

2000-01-01

The Siemens experience with plutonium recycling dates back to the late 1960s. Over the years, extensive research and development programs were performed for the qualification of mixed-oxide (MOX) technology and design methods. Today's typical reload enrichments for uranium and MOX fuel assemblies and modern core designs have become more demanding with respect to accuracy and reliability of design codes. This paper presents the status of plutonium recycling in operating high-burnup pressurized water reactor (PWR) cores. Based on actual examples, it describes the validation status of the design methods and stresses current and future needs for fuel assembly and core design including those related to the disposition of weapons-grade plutonium

Denaturing of plutonium by transmutation of minor-actinides for enhancement of proliferation resistance

International Nuclear Information System (INIS)

Sagara, Hiroshi; Saito, Masaki; Peryoga, Yoga; Ezoubtchenko, Alexey; Takivayev, Alan

2005-01-01

Feasibility study for the plutonium denaturing by utilizing minor-actinide transmutation in light water reactors has been performed. And the intrinsic feature of proliferation resistance of plutonium has been discussed based on IAEA's publication and Kessler's proposal. The analytical results show that not only 238 Pu but also other plutonium isotopes with even-mass-number have very important role for denaturing of plutonium due to their relatively large critical mass and noticeably high spontaneous fission neutron generation. With the change of the minor-actinide doping ratio in U-Pu mix oxide fuel and moderator to fuel ratio, it is found that the reactor-grade plutonium from conventional light water reactors can be denatured to satisfy the proliferation resistance criterion based on the Kessler's proposal but not to be sufficient for the criterion based on IAEA's publication. It has been also confirmed that all the safety coefficients take negative value throughout the irradiation. (author)

Plutonium-239 and americium-241 uptake by plants from soil. Final report

International Nuclear Information System (INIS)

Brown, K.W.

1979-03-01

Alfalfa was grown in soil contaminated with plutonium-239 dioxide (239PuO2) at a concentration of 29.7 nanocuries per gram (nCi/g). In addition to alfalfa, radishes, wheat, rye, and tomatoes were grown in soils contaminated with americium-241 nitrate (241Am(NO3)3) at a concentration of 189 nCi/g. The length of exposure varied from 52 days for the radishes to 237 days for the alfalfa. The magnitude of plutonium incorporation by the alfalfa as indicated by the concentration ratio, 0.0000025, was similar to previously reported data using other chemical forms of plutonium. The results did indicate, however, that differences in the biological availability of plutonium isotopes do exist. All of the species exposed to americium-241 assimilated and translocated this radioisotope to the stem, leaf, and fruiting structures. The magnitude of incorporation as signified by the concentration ratios varied from 0.00001 for the wheat grass to 0.0152 for the radishes. An increase in the uptake of americium also occurred as a function of time for four of the five plant species. Evidence indicates that the predominant factor in plutonium and americium uptake by plants may involve the chelation of these elements in soils by the action of compounds such as citric acid and/or other similar chelating agents released from plant roots

WIMSD4 calculations of the Westinghouse 'EDASA' lattices with plutonium dioxide fuel

International Nuclear Information System (INIS)

Halsall, M.J.

1977-03-01

A series of Westinghouse critical PuO 2 /UO 2 pin-cell assemblies is analysed using the lattice code WIMSD4. The results are presented in terms of computed k-effective values, with comment on the choice of method for calculating high leakage systems and on the adequacy of WIMSD4 for evaluating plutonium enriched lattices. (author)

Precipitation of plutonium (III) oxalate and calcination to plutonium oxide

International Nuclear Information System (INIS)

Esteban, A.; Orosco, E.H.; Cassaniti, P.; Greco, L.; Adelfang, P.

1989-01-01

The plutonium based fuel fabrication requires the conversion of the plutonium nitrate solution from nuclear fuel reprocessing into pure PuO2. The conversion method based on the precipitation of plutonium (III) oxalate and subsequent calcination has been studied in detail. In this procedure, plutonium (III) oxalate is precipitated, at room temperature, by the slow addition of 1M oxalic acid to the feed solution, containing from 5-100 g/l of plutonium in 1M nitric acid. Before precipitation, the plutonium is adjusted to trivalent state by addition of 1M ascorbic acid in the presence of an oxidation inhibitor such as hydrazine. Finally, the precipitate is calcinated at 700 deg C to obtain PuO2. A flowsheet is proposed in this paper including: a) A study about the conditions to adjust the plutonium valence. b) Solubility data of plutonium (III) oxalate and measurements of plutonium losses to the filtrate and wash solution. c) Characterization of the obtained products. Plutonium (III) oxalate has several potential advantages over similar conversion processes. These include: 1) Formation of small particle sizes powder with good pellets fabrication characteristics. 2) The process is rather insensitive to most process variables, except nitric acid concentration. 3) Ambient temperature operations. 4) The losses of plutonium to the filtrate are less than in other conversion processes. (Author) [es

Weapon plutonium in accelerator driven power system

International Nuclear Information System (INIS)

Shvedov, O.V.; Murin, B.P.; Kochurov, B.P.; Shubin, Yu.M.; Volk, V.I.; Bogdanov, P.V.

1997-01-01

Accelerator Driven Systems are planned to be developed for the use (or destruction) of dozens of tons of weapon-grade Plutonium (W-Pu) resulted from the reducing of nuclear weapons. In the paper are compared the parameters of various types of accelerators, the physical properties of various types of targets and blankets, and the results of fuel cycle simulation. Some economical aspects are also discussed

Plutonium-236 traces determination in plutonium-238 by α spectrometry

International Nuclear Information System (INIS)

Acena, M.L.; Pottier, R.; Berger, R.

1969-01-01

Two methods are described in this report for the determination of plutonium-236 traces in plutonium-238 by a spectrometry using semi-conductor detectors. The first method involves a direct comparison of the areas under the peaks of the α spectra of plutonium-236 and plutonium-238. The electrolytic preparation of the sources is carried out after preliminary purification of the plutonium. The second method makes it possible to determine the 236 Pu/ 238 Pu ratio by comparing the areas of the α peaks of uranium-232 and uranium-234, which are the decay products of the two plutonium isotopes respectively. The uranium in the source, also deposited by electrolysis, is separated from a 1 mg amount of plutonium either by a T.L.A. extraction, or by the use of ion-exchange resins. The report ends with a discussion of the results obtained with plutonium of two different origins. (authors) [fr

Plutonium controversy

International Nuclear Information System (INIS)

Gofman, J.W.

1976-01-01

If the world chooses to seek a solution to the energy dilemma through nuclear energy, the element plutonium will become an article of commerce to be handled in quantities of thousands of tonnes annually. Plutonium is a uniquely potent inhalation carcinogen, the potential induction of lung cancer dwarfing other possible toxic effects. For reasons to be presented here, it is the author's opinion that plutonium's carcinogenicity has been very seriously underestimated. If one couples the corrected carcinogenicity with the probable degree of industrial containment of the plutonium, it appears that the commercialization of a plutonium-based energy economy is not an acceptable option for society. Sagan's statement that ''the experience of 30 years supports the contention that plutonium can be used safely'' is manifestly indefensible. No meaningful epidemiological study of plutonium-exposed workers for that 30-year period has ever been done. Since thousands of those possibly exposed have left the industry and are not even available to follow-up, it is doubtful that any meaningful study of ''the experience of 30 years'' will ever be accomplished

Rapid determination of environmental plutonium in large water samples by means of manganese dioxide Co-precipitation and extraction chromatographic separation

International Nuclear Information System (INIS)

Sidhu, R.S.; Hoff, P.

1999-01-01

Plutonium activity determinations in environmental water samples are routinely performed in many laboratories. Due to the low plutonium concentrations and the complexity of the plutonium aqueous chemistry, these analysis involve cumbersome preconcentration and separation procedures and long measurement times. We describe a procedure where MnO 2 (s) is used as scavenger to preconcentrate Pu prior to separation by the transuranium specific extraction chromatographic resin TRU-Resin. The ability of MnO 4 - /MnO 2 (s) to destroy organic matter and oxidise plutonium is combined with the specific behaviour of the TRU-resin for transuranium elements. The method facilitates a rapid preconcentration and separation of plutonium. With the use of this procedure, the laboratory work on one sample can be performed in one day with minimum attention. The overall yields from a 200 litre fresh- or seawater sample to a measurable Pu source are between 70-85%. (orig.)

Preparation of hexavalent plutonium and its determination in the presence of tetravalent plutonium; Preparation de plutonium hexavalent et dosage en presence de plutonium tetravalent

Energy Technology Data Exchange (ETDEWEB)

Corpel, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Corpel, J [Institut du Radium, 75 - Paris (France)

1958-07-01

In order to study the eventual reduction of plutonium from the VI-valent state to the IV-valent state, in sulphuric medium, under the influence of its own {alpha} radiation or of the {gamma}-rays from a cobalt-60 source, we have developed a method for preparing pure hexavalent plutonium and two methods for determining solutions containing tetravalent and hexavalent plutonium simultaneously. Hexavalent plutonium was prepared by anodic oxidation at a platinum electrode. Study of the oxidation yield as a function of various factors has made it possible to define experimental conditions giving complete oxidation. For concentrations in total plutonium greater than 1.5 x 10{sup -3} M, determination of the two valencies IV and VI was carried out by spectrophotometry at two wavelengths. For lower concentrations, the determination was done by counting, after separation of the tetravalent plutonium in the form of fluoride in the presence of a carrier. (author) [French] Afin d'etudier l'eventuelle reduction du plutonium de l'etat de valence VI a l'etat de valence IV, en milieu sulfurique sous l'influence de son propre rayonnement {alpha} ou des rayons {gamma} d'une source de cobalt-60, nous avons mis au point une methode de preparation de plutonium hexavalent pur et deux methodes de dosage des solutions contenant simultanement du plutonium tetravalent et du plutonium hexavalent. Nous avons prepare le plutonium hexavalent par oxydation anodique au contact d'une electrode de platine. L'etude de rendement de l'oxydation en fonction des divers facteurs nous a permis de definir des conditions experimentales donnant une oxydation complete. Pour des concentrations en plutonium total superieures a 1,5.10{sup -3} M, le dosage des deux valences IV et VI a ete realise par spectrophotometrie a deux longueurs d'onde. Pour des concentrations inferieures, le dosage a ete effectue par comptage apres separation du plutonium tetravalent sous la forme du fluorure en presence d'un entraineur

Plutonium in nature

International Nuclear Information System (INIS)

Madic, C.

1994-01-01

Plutonium in nature comes from natural sources and anthropogenic ones. Plutonium at the earth surface comes principally from anthropogenic sources. It is easily detectable in environment. The plutonium behaviour in environment is complex. It seems necessary for the future to reduce releases in environment, to improve predictive models of plutonium behaviour in geosphere, to precise biological impact of anthropogenic plutonium releases

Disposition of plutonium from dismantled nuclear weapons: Fission options and comparisons

International Nuclear Information System (INIS)

Omberg, R.P.; Walter, C.E.

1993-01-01

Over the next decade, the United States expects to recover about 50 Mg of excess weapon plutonium and the Republic of Russia expects to recover a similar amount. Ensuring that these large quantities of high-grade material are not reused in nuclear weapons has drawn considerable attention. In response to this problem, the US Department of Energy (DOE) chartered the Plutonium Disposition Task Force (PDTF), in the summer of 1992, to assess a range of practical means for disposition of excess US plutonium. This report summarizes and compares the ''Fission Options'' provided to the Fission Working Group Review Committee (the committee) of the PDTF. The review by the committee was based on preliminary information received as of December 4, 1992, and as such the results summarized in this report should also be considered preliminary. The committee concluded that irradiation of excess weapon plutonium in fission reactors in conjunction with the generation of electricity and storing the spent fuel is a fast, cost-effective, and environmentally acceptable method of addressing the safeguards (diversion) issue. When applied appropriately, this method is consistent with current nonproliferation policy. The principal effect of implementing the fission options is at most a moderate addition of plutonium to that existing in commercial spent fuel. The amount of plutonium in commercial spent fuel by the year 2000 is estimated to be 300 Mg. The addition of 50 Mg of excess weapon plutonium, in this context, is not a determining factor, moreover, several of the fission options achieve substantial annihilation of plutonium

SEPARATION OF PLUTONIUM

Science.gov (United States)

Maddock, A.G.; Smith, F.

1959-08-25

A method is described for separating plutonium from uranium and fission products by treating a nitrate solution of fission products, uranium, and hexavalent plutonium with a relatively water-insoluble fluoride to adsorb fission products on the fluoride, treating the residual solution with a reducing agent for plutonium to reduce its valence to four and less, treating the reduced plutonium solution with a relatively insoluble fluoride to adsorb the plutonium on the fluoride, removing the solution, and subsequently treating the fluoride with its adsorbed plutonium with a concentrated aqueous solution of at least one of a group consisting of aluminum nitrate, ferric nitrate, and manganous nitrate to remove the plutonium from the fluoride.

Incineration method for plutonium recovery from alpha contaminated organic compounds

International Nuclear Information System (INIS)

Yahata, Taneaki; Abe, Jiro; Kato, Michiharu; Kurihara, Masayoshi

1985-01-01

An incineration method for plutonium recovery from α contaminated organic compounds in a flow of controlled oxygen gas is stated. The species of such thermal decomposition products as hydrocarbons, free carbon, carbon monoxide and hydrogen were determined by mass spectrography. The mixture of the products which are the source of tar or soot was converted to CO 2 and H 2 O in contact with copper oxide catalyst without flaming. This incineration method is composed of two stages. The first stage is the decomposition of organic compounds in the streams of gas mixtures containing oxygen in low ratios. The second stage is the incineration of the decomposition products by catalytic reaction in the streams of gas with higher oxygen ratios. Plutonium was recovered as the form of plutonium dioxide from the incineration residues of the first stage. The behavior of oil was examined as a representative of liquid organic compounds. It was found to evaporate below ca. 500 0 C, but was completely incinerated by the catalytic reaction with copper oxide catalyst in the flow of gas with controlled oxygen amount and was changed to CO 2 and H 2 O. (author)

DOE plutonium disposition study: Analysis of existing ABB-CE Light Water Reactors for the disposition of weapons-grade plutonium

International Nuclear Information System (INIS)

1994-01-01

Core reactivity and basic fuel management calculations were conducted on the selected reactors (with emphasis on the System 80 units as being the most desirable choice). Methods used were identical to those reported in the Evolutionary Reactor Report. From these calculations, the basic mission capability was assessed. The selected reactors were studied for modification, such as the addition of control rod nozzles to increase rod worth, and internals and control system modifications that might also be needed. Other system modifications studied included the use of enriched boric acid as soluble poison, and examination of the fuel pool capacities. The basic geometry and mechanical characteristics, materials and fabrication techniques of the fuel assemblies for the selected existing reactors are the same as for System 80+. There will be some differences in plutonium loading, according to the ability of the reactors to load MOX fuel. These differences are not expected to affect licensability or EPA requirements. Therefore, the fuel technology and fuel qualification sections provided in the Evolutionary Reactor Report apply to the existing reactors. An additional factor, in that the existing reactor availability presupposes the use of that reactor for the irradiation of Lead Test Assemblies, is discussed. The reactor operating and facility licenses for the operating plants were reviewed. Licensing strategies for each selected reactor were identified. The spent fuel pool for the selected reactors (Palo Verde) was reviewed for capacity and upgrade requirements. Reactor waste streams were identified and assessed in comparison to uranium fuel operations. Cost assessments and schedules for converting to plutonium disposition were estimated for some of the major modification items. Economic factors (incremental costs associated with using weapons plutonium) were listed and where possible under the scope of work, estimates were made

Peaceful uses of nuclear weapon plutonium

International Nuclear Information System (INIS)

Burtak, F.

1996-01-01

In 1993, the U.S.A. and the CIS signed Start 2 (the Strategic Arms Reduction Treaty) in which they committed themselves the reduce their nuclear weapon arsenals to a fraction of that of 1991. For forty-five years the antagonism between the superpowers had been a dominating factor in world history, determining large areas of social life. When Start 2 will have been completed in 2003, some 200 t of weapon grade plutonium and some 2000 t of highly enriched uranium (Heu) will arise from dismantling nuclear weapons. In the absence of the ideological ballast of the debate about Communism versus Capitalism of the past few decades there is a chance of the grave worldwide problem of safe disposal and utilization of this former nuclear weapon material being solved. Under the heading of 'swords turned into plowshares', plutonium and uranium could be used for peaceful electricity generation. (orig.) [de

Using an induction melter with a cold crucible for the immobilization of plutonium

Energy Technology Data Exchange (ETDEWEB)

Kushnikov, V.V.; Matiunin, Yu.I.; Smelova, T.V. [A.A. Bochvara All Russian Scientific Research Institute of Non-Organic Materials, Moscow (Russian Federation)

1996-05-01

This report evaluates the possibilities for immobilizing weapons-grade plutonium in glass-type materials that satisfy requirements for eventual burial in deep geologic repositories and correspond to the standards set for spent fuel.

The plutonium fuel cycles

International Nuclear Information System (INIS)

Pigford, T.H.; Ang, K.P.

1975-01-01

The quantities of plutonium and other fuel actinides have been calculated for equilibrium fuel cycles for 1000-MW water reactors fueled with slightly enriched uranium, water reactors fueled with plutonium and natural uranium, fast-breder reactors, gas-cooled reactors fueled with thorium and highly enriched uranium, and gas-cooled reactors fueled with thorium, plutonium and recycled uranium. The radioactivity quantities of plutonium, americium and curium processed yearly in these fuel cycles are greatest for the water reactors fueled with natural uranium and recycled plutonium. The total amount of actinides processed is calculated for the predicted future growth of the U.S. nuclear power industry. For the same total installed nuclear power capacity, the introduction of the plutonium breeder has little effect upon the total amount of plutonium in this century. The estimated amount of plutonium in the low-level process wastes in the plutonium fuel cycles is comparable to the amount of plutonium in the high-level fission product wastes. The amount of plutonium processed in the nuclear fuel cycles can be considerably reduced by using gas-cooled reactors to consume plutonium produced in uranium-fueled water reactors. These, and other reactors dedicated for plutonium utilization, could be co-located with facilities for fuel reprocessing ad fuel fabrication to eliminate the off-site transport of separated plutonium. (author)

Food grade titanium dioxide disrupts intestinal brush border microvilli in vitro independent of sedimentation.

Science.gov (United States)

Faust, James J; Doudrick, Kyle; Yang, Yu; Westerhoff, Paul; Capco, David G

2014-06-01

Bulk- and nano-scale titanium dioxide (TiO2) has found use in human food products for controlling color, texture, and moisture. Once ingested, and because of their small size, nano-scale TiO2 can interact with a number of epithelia that line the human gastrointestinal tract. One such epithelium responsible for nutrient absorption is the small intestine, whose constituent cells contain microvilli to increase the total surface area of the gut. Using a combination of scanning and transmission electron microscopy it was found that food grade TiO2 (E171 food additive coded) included ∼25% of the TiO2 as nanoparticles (NPs; TiO2 sedimentation. It was found that TiO2 isolated from the candy coating of chewing gum and a commercially available TiO2 food grade additive samples were of the anatase crystal structure. Exposure to food grade TiO2 additives, containing nanoparticles, at the lowest concentration tested within this experimental paradigm to date at 350 ng/mL (i.e., 100 ng/cm(2) cell surface area) resulted in disruption of the brush border. Through the use of two independent techniques to remove the effects of gravity, and subsequent TiO2 sedimentation, it was found that disruption of the microvilli was independent of sedimentation. These data indicate that food grade TiO2 exposure resulted in the loss of microvilli from the Caco-2BBe1 cell system due to a biological response, and not simply a physical artifact of in vitro exposure.

The combined effects of plutonium and cigarette smoke on the production of lung tumours

International Nuclear Information System (INIS)

Priest, N.D.; Moores, S.R.; Black, A.; Talbot, R.; Morgan, A.

1989-01-01

An experiment was conducted to determine the effect of exposure to cigarette smoke on the incidence of plutonium induced lung tumours in mice. Approximately 130 female CBA/H mice were used. These were exposed to plutonium-239 dioxide to give an initial alveolar deposit of 100 Bq, then treated in one of three ways. One third received no further treatment and were held for a period of 18 months. The remainder were either sham-exposed or exposed to mainstream cigarette smoke for one year then held for a further 6 months. After this all the animals were killed. The control mice - that had received only plutonium -contained more tumours than mice that were also either sham-exposed or exposed to cigarette smoke. The lowest number of tumours was found in the group exposed to smoke. These results indicate that, under some circumstances, the effects of cigarette smoke and of alpha-irradiation of the lung can be antagonistic, contrasting with a common expectation of synergy. (author)

Plutonium

International Nuclear Information System (INIS)

Anon.

1995-01-01

Plutonium, which was obtained and identified for the first time in 1941 by chemist Glenn Seaborg - through neutron irradiation of uranium 238 - is closely related to the history of nuclear energy. From the very beginning, because of the high radiotoxicity of plutonium, a tremendous amount of research work has been devoted to the study of the biological effects and the consequences on the environment. It can be said that plutonium is presently one of the elements, whose nuclear and physico-chemical characteristics are the best known. The first part of this issue is a survey of the knowledge acquired on the subject, which emphasizes the sanitary effects and transfer into the environment. Then the properties of plutonium related to energy generation are dealt with. Fissionable, like uranium 235, plutonium has proved a high-performance nuclear fuel. Originally used in breeder reactors, it is now being more and more widely recycled in light water reactors, in MOX fuel. Reprocessing, recycling and manufacturing of these new types of fuel, bound of become more and more widespread, are now part of a self-consistent series of operations, whose technical, economical, industrial and strategical aspects are reviewed. (author)

Learning more about plutonium

International Nuclear Information System (INIS)

2005-01-01

This document offers chemical, metallurgical and economical information on the plutonium, a hard white radioelement. It deals also on the plutonium formation in the earth, the plutonium use in the nuclear industry, the plutonium in the environment and the plutonium toxicity. (A.L.B.)

Plutonium Consumption Program, CANDU Reactor Project final report

Energy Technology Data Exchange (ETDEWEB)

1994-07-31

DOE is investigating methods for long term dispositioning of weapons grade plutonium. One such method would be to utilize the plutonium in Mixed OXide (MOX) fuel assemblies in existing CANDU reactors. CANDU (Canadian Deuterium Uranium) reactors are designed, licensed, built, and supported by Atomic Energy of Canada Limited (AECL), and currently use natural uranium oxide as fuel. The MOX spent fuel assemblies removed from the reactor would be similar to the spent fuel currently produced using natural uranium fuel, thus rendering the plutonium as unattractive as that in the stockpiles of commercial spent fuel. This report presents the results of a study sponsored by the DOE for dispositioning the plutonium using CANDU technology. Ontario Hydro`s Bruce A was used as reference. The fuel design study defined the optimum parameters to disposition 50 tons of Pu in 25 years (or 100 tons). Two alternate fuel designs were studied. Safeguards, security, environment, safety, health, economics, etc. were considered. Options for complete destruction of the Pu were also studied briefly; CANDU has a superior ability for this. Alternative deployment options were explored and the potential impact on Pu dispositioning in the former Soviet Union was studied. An integrated system can be ready to begin Pu consumption in 4 years, with no changes required to the reactors other than for safe, secure storage of new fuel.

Plutonium Consumption Program, CANDU Reactor Project final report

International Nuclear Information System (INIS)

1994-01-01

DOE is investigating methods for long term dispositioning of weapons grade plutonium. One such method would be to utilize the plutonium in Mixed OXide (MOX) fuel assemblies in existing CANDU reactors. CANDU (Canadian Deuterium Uranium) reactors are designed, licensed, built, and supported by Atomic Energy of Canada Limited (AECL), and currently use natural uranium oxide as fuel. The MOX spent fuel assemblies removed from the reactor would be similar to the spent fuel currently produced using natural uranium fuel, thus rendering the plutonium as unattractive as that in the stockpiles of commercial spent fuel. This report presents the results of a study sponsored by the DOE for dispositioning the plutonium using CANDU technology. Ontario Hydro's Bruce A was used as reference. The fuel design study defined the optimum parameters to disposition 50 tons of Pu in 25 years (or 100 tons). Two alternate fuel designs were studied. Safeguards, security, environment, safety, health, economics, etc. were considered. Options for complete destruction of the Pu were also studied briefly; CANDU has a superior ability for this. Alternative deployment options were explored and the potential impact on Pu dispositioning in the former Soviet Union was studied. An integrated system can be ready to begin Pu consumption in 4 years, with no changes required to the reactors other than for safe, secure storage of new fuel

Kr-85 signatures for various plutonium production schemes

Energy Technology Data Exchange (ETDEWEB)

Stanoszek, Paul [Carl Friedrich von Weizsaecker-Centre for Science and Peace Research (Germany)

2009-07-01

Kr-85 is considered to be the best atmospheric indicator of unreported weapon-grade material production. This fact is based on the half-life of 10.76 years of Kr-85 and its chemical inactivity, which makes it even detectable after extended periods of cooling time. Kr-85 is produced as fission product during nuclear reactor operation and remains in the fuel until reprocessing starts. In order to determine the detectability of plutonium production the Kr-85 source term has to be assessed. The important issue of this presentation is the question on the minimum signal that an inspector can expect under the assumption that a proliferator minimizes his Kr-85 generation in order to circumvent a Kr-85 detection. A further assumption is that for nuclear weapon production a burn-up of typically around 2 MWd/kg is used. In addition, if clandestine plutonium production takes place, the source term might be used to estimate the amount of separated plutonium. The methodology of this study is based on a linkage between MCNPX and MATLAB. All results for actinide concentrations and Kr-85 are evaluated for different enrichments of U-235 and compared to known literature data. The Kr-85 source term per kilogram plutonium depends on the enrichments. As a result the lowest Kr-85 source term is found for depleted uranium.

U.S. weapons-usable plutonium disposition policy: Implementation of the MOX fuel option

Energy Technology Data Exchange (ETDEWEB)

Woods, A.L. [ed.] [Amarillo National Resource Center for Plutonium, TX (United States); Gonzalez, V.L. [Texas A and M Univ., College Station, TX (United States). Dept. of Political Science

1998-10-01

A comprehensive case study was conducted on the policy problem of disposing of US weapons-grade plutonium, which has been declared surplus to strategic defense needs. Specifically, implementation of the mixed-oxide fuel disposition option was examined in the context of national and international nonproliferation policy, and in contrast to US plutonium policy. The study reveals numerous difficulties in achieving effective implementation of the mixed-oxide fuel option including unresolved licensing and regulatory issues, technological uncertainties, public opposition, potentially conflicting federal policies, and the need for international assurances of reciprocal plutonium disposition activities. It is believed that these difficulties can be resolved in time so that the implementation of the mixed-oxide fuel option can eventually be effective in accomplishing its policy objective.

U.S. weapons-useable plutonium disposition policy: Implementation of the MOX fuel option

International Nuclear Information System (INIS)

Woods, A.L.; Gonzalez, V.L.

1998-10-01

A comprehensive case study was conducted on the policy problem of disposing of US weapons-grade plutonium, which has been declared surplus to strategic defense needs. Specifically, implementation of the mixed-oxide fuel disposition option was examined in the context of national and international nonproliferation policy, and in contrast to US plutonium policy. The study reveals numerous difficulties in achieving effective implementation of the mixed-oxide fuel option including unresolved licensing and regulatory issues, technological uncertainties, public opposition, potentially conflicting federal policies, and the need for international assurances of reciprocal plutonium disposition activities. It is believed that these difficulties can be resolved in time so that the implementation of the mixed-oxide fuel option can eventually be effective in accomplishing its policy objective

Management of super-grade plutonium in spent nuclear fuel

International Nuclear Information System (INIS)

McFarlane, H. F.; Benedict, R. W.

2000-01-01

This paper examines the security and safeguards implications of potential management options for DOE's sodium-bonded blanket fuel from the EBR-II and the Fermi-1 fast reactors. The EBR-II fuel appears to be unsuitable for the packaging alternative because of DOE's current safeguards requirements for plutonium. Emerging DOE requirements, National Academy of Sciences recommendations, draft waste acceptance requirements for Yucca Mountain and IAEA requirements for similar fuel also emphasize the importance of safeguards in spent fuel management. Electrometallurgical treatment would be acceptable for both fuel types. Meeting the known requirements for safeguards and security could potentially add more than $200M in cost to the packaging option for the EBR-II fuel

Civil plutonium management

International Nuclear Information System (INIS)

Sicard, B.; Zaetta, A.

2004-01-01

During 1960 and 1970 the researches on the plutonium recycling in fast neutrons reactors were stimulated by the fear of uranium reserves diminishing. At the beginning of 1980, the plutonium mono-recycling for water cooled reactors is implementing. After 1990 the public opinion concerning the radioactive wastes management and the consequences of the disarmament agreements between Russia and United States, modified the context. This paper presents the today situation and technology associated to the different options and strategical solutions of the plutonium management: the plutonium use in the world, the neutronic characteristics, the plutonium effect on the reactors characteristics, the MOX behavior in the reactors, the MOX fabrication and treatment, the possible improvements to the plutonium use, the concepts performance in a nuclear park. (A.L.B.)

The plutonium society

International Nuclear Information System (INIS)

Mez, L.; Richter, M.

1981-01-01

The lectures of an institute are reported on, which took place between 25th and 27th January 1980 in Berlin. The subsequent public panel discussion with representations from the political parties is then documentated in a few press-reports. The themes of the 8 lectures are: views and facts on plutonium, plutonium as an energy resource, military aspects of the production of plutonium, economic aspects of the plutonium economy, the position of the trade unions on the industrial reconversion, the alleged inevitability of a plutonium society and the socio-political alternatives and perspectives of nuclear waste disposal. (UA) [de

What is plutonium stabilization, and what is safe storage of plutonium?

International Nuclear Information System (INIS)

Forsberg, C.W.

1995-01-01

The end of the cold war has resulted in the shutdown of nuclear weapons production and the start of dismantlement of significant numbers of nuclear weapons. This, in turn, is creating an inventory of plutonium requiring interim and long-term storage. A key question is, ''What is required for safe, multidecade, plutonium storage?'' The requirements for storage, in turn, define what is needed to stabilize the plutonium from its current condition into a form acceptable for interim and long-term storage. Storage requirements determine if research is required to (1) define required technical conditions for interim and long-term storage and (2) develop or improve current stabilization technologies. Storage requirements depend upon technical, policy, and economic factors. The technical issues are complicated by several factors. Plutonium in aerosol form is highly hazardous. Plutonium in water is hazardous. The plutonium inventory is in multiple chemical forms--some of which are chemically reactive. Also, some of the existing storage forms are clearly unsuitable for storage periods over a few years. Gas generation by plutonium compounds complicates storage: (1) all plutonium slowly decays creating gaseous helium and (2) the radiation from plutonium decay can initiate many chemical reactions-some of which generate significant quantities of gases. Gas generation can pressurize sealed storage packages. Last nuclear criticality must be avoided

Experience and activities in the field of plutonium recycling in civilian nuclear power plants in the European Union

International Nuclear Information System (INIS)

Decressin, A.; Gambier, D.J.; Lehmann, J.-P.; Nietzold, D.E.

1996-01-01

The European Union industry has established a world-wide leadership position in manufacturing and exploiting plutonium bearing fuel (MOX). About 15 to 20 tons of plutonium have been manufactured in the MOX fuel fabrication plants of E.U. companies. The current capacity of about 60 tons of MOX fuel per year is being upgraded to reach 400 tons/year by the year 2000. As a result, the excess amounts of separated plutonium, presently stored in the European Union, should no longer raise but should steadily decrease to converge to zero. Studies by the European Commission have indicated that the best use at present of weapons-grade and reactor-grade plutonium is to burn it in operating and future planned nuclear reactors. Disposing of plutonium by blending it with fission products or immobilising it into synthetic matrices appears to be far from being an industrially viable option. Following this path would mean to continue storing the excess plutonium of both military and civilian origin for an unknown, but very long period of time. For these and other reasons, the European Commission is striving to foster international cooperation between the European Union companies, having a long industrial experience accumulated in the field of recycling plutonium, and, so far, the Russian Federation and the Newly Independent States. This cooperation is aiming at supporting projects that could be mutually beneficial to all parties involved. To meet this objective, several programmes have been established either bilaterally or multilaterally, in particular within the framework of the International Science and Technology Centre (I.S.T.C.) in Moscow. Some examples of such collaborations will be described. (author)

Combined evaluation. Plutonium transports in France. Problems of safety and reliability of transport container FS47; Evaluation Conjointe. Transports de plutonium en France. Problemes de surete et de securite du container de transport FS47

Energy Technology Data Exchange (ETDEWEB)

Marignac, Y.; Coeytaux, X. [Wise-Paris, 75 (France); Large, J.H. [Nuclear Engineer, Large and Associates, Londres (United Kingdom)

2004-09-15

This report concerns the safety and the protection of plutonium dioxide transported from Cogema La Hague to the mixed oxide fuel plant of Marcoule and Cadarache. The French approach of the transport safety is based on the combining of two essential principles: the first one affirms that the performances of the FS47 container in regard of containment (norms TS-R-1 from IAEA for the accidental conditions) is conceived to resist in any situation even terrorism or sabotage. In fact, the IAEA norm follows a probabilistic study without a voluntary attack such a terrorist one. The second principle rests on the ability to prevent the treat of terrorism acts, because of a secrecy policy on the plutonium transport. It appeared that the Green peace association has succeeded several times to know exactly the hours, the trips of the plutonium transport and this simple thing raises more questions than it solves. (N.C.)

Protected Plutonium Production by Transmutation of Minor Actinides for Peace and Sustainable Prosperity [O1] - Fundamentals of P{sup 3} Mechanism and Methodology Development for Plutonium Categorization

Energy Technology Data Exchange (ETDEWEB)

Saito, Masaki [Research Laboratory for Nuclear Reactor, Tokyo Institute of Technology, 2-12-1 Ookayama, Meguro, Tokyo, 1528550 (Japan)

2009-06-15

'Protected Plutonium Production (P{sup 3})' has been proposed to enhance the proliferation resistance of plutonium by the transmutation of Minor Actinides (MAs). Doping the small amount of MAs such as {sup 237}Np or {sup 241}Am with large neutron capture cross-section into the uranium fuel to enhance the production of {sup 238}Pu or {sup 242}Pu, which have high spontaneous fission neutron source or also high decay heat to makes the process of the nuclear weapon manufacture and maintenance technologically difficult, can be effective for improving the isotopic barrier of proliferation resistance of the plutonium in thermal reactors. Super weapon grade plutonium could be produced in the blanket of a conventional FBR. However, by increasing the {sup 238}Pu or {sup 242}Pu ratio in the total plutonium by MAs doping into the fresh blanket, the protected plutonium with high proliferation-resistance can be bred. A new evaluation function, 'attractiveness', defined as a ratio of potential of fission yield to the technological difficulties of nuclear explosive device, has been proposed to evaluate the proliferation resistance of Pu based on the nuclear material property for Plutonium Categorization. In the conference, the fundamentals of P{sup 3} mechanism by transmutation of MA, and the comparison of the 'attractiveness' of the Pu produced in advanced reactors based on P{sup 3} mechanism and in the conventional reactors will be presented. Instead of the geological disposal or just their burning of MAs by the fission reaction, they should be treated as valuable fertile materials to enhance the proliferation resistance of plutonium produced in the thermal and fast breeder reactors for peace and sustainable prosperity in future. Acknowledgement: Some parts of this work have been supported by the Ministry of Education, Culture, Sports, Science and Technology in Japan. (authors)

An ab initio study of plutonium oxides surfaces

International Nuclear Information System (INIS)

Jomard, G.; Bottin, F.; Amadon, B.

2007-01-01

By means of first-principles calculations, we have studied the atomic structure as well as the thermodynamic stability of various plutonium dioxide surfaces in function of their environment (in terms of oxygen partial pressure and temperature). All these simulations have been performed with the ABINIT code. It is well known that DFT fails to describe correctly plutonium-based materials since 5f electrons in such systems are strongly correlated. In order to go beyond DFT, we have treated PuO 2 and β-Pu 2 O 3 in a DFT+U framework. We show that the couple of parameters (U,J) that works well for pure Pu is also well designed for describing ground state (GS) properties of these two oxides. The major improvement with respect with DFT is that we are able to predict an insulating GS in agreement with experiments. The presence of a gap in the DOS (Density of States) of plutonium oxides should play a significant role in the predicted surface reactivity. However, performing DFT+U calculations on surfaces of plutonium oxide from scratch was too ambitious. That is why we decided, as a first step, to study the stability of the (100), (110) and (111) surfaces of PuO 2 in a DFT-GGA framework. For each of these orientations, we considered various terminations. These ab initio results have been introduced in a thermodynamic model which allows us to predict the relative stability of the different terminations as a function of temperature and oxygen partial pressure (p O 2 ). We conclude that at room temperature and for p O 2 ∼10 atm., the polar O 2 -(100) termination is favoured. The stabilization of such a polar stoichiometric surface is surprising and should be confirmed by DFT+U calculations before any final conclusion. (authors)

Determination of trace metals in nuclear-grade uranium dioxide by X-ray fluorescence spectrometry

International Nuclear Information System (INIS)

Salvador, V.L.R.; Imakuma, K.

1988-04-01

A method is described for the simultaneous determination of low concentrations of Ca, Cr, Cu, Fe, Mn and Ni in nuclear-grade uranium dioxide by X-ray fluorescence spectrometry, without the use of chemical treatment. The lower limits of detection range from 2 μg g -1 for nickel and manganese to 5 μg g -1 for copper. Samples are prepared in the form of double-layer pellets with boric acid as a binding agent. Standards are prepared in a U 3 O 8 matrix, which is more chemically stable than UO 2 and has similar matrix behaviour. The correlation coefficients for calibration curves are better than 0.999. Erros range from 2.4 % for chromium to 6.8 % for nickel. (author) [pt

Corrosive gas generation potential from chloride salt radiolysis in plutonium environments

International Nuclear Information System (INIS)

Tandon, L.; Allen, T.H.; Mason, R.E.; Penneman, R.A.

1999-01-01

The specific goal of this project was to evaluate the magnitude and practical significance of radiation effects involving mixtures of chloride salts and plutonium dioxide (PuO 2 ) sealed in stainless steel containers and stored for up to 50 yr, after stabilization at 950 C and packaging according to US Department of Energy (DOE) standards. The potential for generating chemically aggressive molecular chlorine (and hydrogen chloride by interaction with adsorbed water or hydrogen gas) by radiolysis of chloride ions was studied. To evaluate the risks, an annotated bibliography on chloride salt radiolysis was created with emphasis on effects of plutonium alpha radiation. The authors present data from the material identification and surveillance (MIS) project obtained from examination and analysis of representative PuO 2 items from various DOE sites, including the headspace gas analysis data of sealed mixtures of PuO 2 and chloride salts following long-term storage

Plutonium solubilities

International Nuclear Information System (INIS)

Puigdomnech, I.; Bruno, J.

1991-02-01

Thermochemical data has been selected for plutonium oxide, hydroxide, carbonate and phosphate equilibria. Equilibrium constants have been evaluated in the temperature range 0 to 300 degrees C at a pressure of 1 bar to T≤100 degrees C and at the steam saturated pressure at higher temperatures. Measured solubilities of plutonium that are reported in the literature for laboratory experiments have been collected. Solubility data on oxides, hydroxides, carbonates and phosphates have been selected. No solubility data were found at temperatures higher than 60 degrees C. The literature solubility data have been compared with plutonium solubilities calculated with the EQ3/6 geochemical modelling programs, using the selected thermodynamic data for plutonium. (authors)

Plutonium in uranium deposits

International Nuclear Information System (INIS)

Curtis, D.; Fabryka-Martin, J.; Aguilar, R.; Attrep, M. Jr.; Roensch, F.

1992-01-01

Plutonium-239 (t 1/2 , 24,100 yr) is one of the most persistent radioactive constituents of high-level wastes from nuclear fission power reactors. Effective containment of such a long-lived constituent will rely heavily upon its containment by the geologic environment of a repository. Uranium ore deposits offer a means to evaluate the geochemical properties of plutonium under natural conditions. In this paper, analyses of natural plutonium in several ores are compared to calculated plutonium production rates in order to evaluate the degree of retention of plutonium by the ore. The authors find that current methods for estimating production rates are neither sufficiently accurate nor precise to provide unambiguous measures of plutonium retention. However, alternative methods for evaluating plutonium mobility are being investigated, including its measurement in natural ground waters. Preliminary results are reported and establish the foundation for a comprehensive characterization of plutonium geochemistry in other natural environments

The use of plutonium

International Nuclear Information System (INIS)

Marshall, W.

1980-01-01

The use of plutonium as a vital energy source producing maximum economic benefit with minimum proliferation risks is discussed. Having considered the production of plutonium, several possible plutonium fuel cycle options are identified and the economic value to be attached to plutonium for each examined. It is shown how the use of plutonium in fast reactors gives an opportunity for a non-proliferation policy not available when plutonium is used only in thermal reactors. From the technical considerations reviewed concerning plutonium and fast reactors it is shown that an economic regime involving international trade in spent thermal reactor fuel is possible which benefits equally those countries with fast reactors and those without and also assists in avoiding the proliferation of nuclear weapons. (U.K.)

Properties of plutonium

International Nuclear Information System (INIS)

Ahn, Jin Su; Yoon, Hwan Ki; Min, Kyung Sik; Kim, Hyun Tae; Ahn, Jong Sung; Kwag, Eon Ho; Ryu, Keon Joong

1996-03-01

Plutonium has unique chemical and physical properties. Its uniqueness in use has led to rare publications, in Korea. This report covers physical aspects of phase change of metal plutonium, mechanical properties, thermal conductivity, etc, chemical aspects of corrosion, oxidation, how to produce plutonium from spent fuels by describing various chemical treatment methods, which are currently used and were used in the past. It also contains characteristics of the purex reprocessing process which is the most widely used nowadays. And show processes to purify and metalize from recovered plutonium solution. Detection and analysis methods are introduced with key pints for handling, critical safety, toxicity, and effects on peoples. This report gives not only a general idea on what plutonium is, rather than deep technical description, but also basic knowledge on plutonium production and safeguards diversion from the view point of nonproliferation. 18 refs. (Author) .new

Properties of plutonium

Energy Technology Data Exchange (ETDEWEB)

Ahn, Jin Su; Yoon, Hwan Ki; Min, Kyung Sik; Kim, Hyun Tae; Ahn, Jong Sung; Kwag, Eon Ho; Ryu, Keon Joong [Korea Atomic Energy Research Institute, Daeduk (Korea, Republic of)

1996-03-01

Plutonium has unique chemical and physical properties. Its uniqueness in use has led to rare publications, in Korea. This report covers physical aspects of phase change of metal plutonium, mechanical properties, thermal conductivity, etc, chemical aspects of corrosion, oxidation, how to produce plutonium from spent fuels by describing various chemical treatment methods, which are currently used and were used in the past. It also contains characteristics of the purex reprocessing process which is the most widely used nowadays. And show processes to purify and metalize from recovered plutonium solution. Detection and analysis methods are introduced with key pints for handling, critical safety, toxicity, and effects on peoples. This report gives not only a general idea on what plutonium is, rather than deep technical description, but also basic knowledge on plutonium production and safeguards diversion from the view point of nonproliferation. 18 refs. (Author) .new.

High-temperature enthalpies of plutonium monocarbide and plutonium sesquicarbide

International Nuclear Information System (INIS)

Oetting, F.L.

1979-01-01

The high-temperature enthalpies of plutonium monocarbide and plutonium sesquicarbide have been determined with a copper-block calorimeter of the isoperibol type. The experimental enthalpy data, which was measured relative to 298 K, covered the temperature range from 400 to 1500 K. The calculation of the temperature rise of the calorimeter takes into account the added heat evolution from the radioactive decay of the plutonium samples. These enthalpy results, combined with the heat capacity and entropy of the respective carbide at 298 K available from the literature, has made it possible to generate tables of thermodynamic functions for the plutonium carbides. The behavior of the heat capacity of both of the plutonium carbides, i.e., a relatively steep increase in the heat capacity as the temperature increases, may be attributed to a premelting effect with the formation of vacancies within the crystal lattice although a theoretical treatment of this phenomenon is not given

Influence of cow urine in the bioavailability of plutonium oxide particles in Palomares soils

Energy Technology Data Exchange (ETDEWEB)

Espinosa, A.; Aragon, A.; De La Cruz, B.; Gutierrez, J. [CIEMAT, DIAE, Madrid (Spain)

2004-07-01

The nuclear accident that occurred in Palomares in 1966 caused the release of plutonium weapon grade particles into a Mediterranean ecosystem, and consequently, urban and farming areas were contaminated with this material. Several studies focussed on the characterization and behaviour of trans-uranides have been carried out in the area. In this work, the solubility evolution of plutonium is analysed for a period of more than 30 years, as well as the influence that the incorporation of cow urine into organic fertilizers has on the solubility of the mentioned element. The average value of the plutonium solubility in water determined in five samples was 0.008% in 1986. However, determinations carried out in samples taken in 1999 and 2000 indicated an increase of the plutonium solubility of 22 to 96 times higher. In order to check the influence of organic fertilizers on the solubility of plutonium, a solubility test was carried out using cow urine as extracting solution. The results show that the solubility of plutonium can reach a value equal to 14%, which is similar to the one obtained with sodium pyrophosphate acting as extracting solution. Thus, these results are a clear warning of what might happen if organic fertilizers are used in transuranic-contaminated soils. (author)

Influence of cow urine in the bioavailability of plutonium oxide particles in Palomares soils

International Nuclear Information System (INIS)

Espinosa, A.; Aragon, A.; De La Cruz, B.; Gutierrez, J.

2004-01-01

The nuclear accident that occurred in Palomares in 1966 caused the release of plutonium weapon grade particles into a Mediterranean ecosystem, and consequently, urban and farming areas were contaminated with this material. Several studies focussed on the characterization and behaviour of trans-uranides have been carried out in the area. In this work, the solubility evolution of plutonium is analysed for a period of more than 30 years, as well as the influence that the incorporation of cow urine into organic fertilizers has on the solubility of the mentioned element. The average value of the plutonium solubility in water determined in five samples was 0.008% in 1986. However, determinations carried out in samples taken in 1999 and 2000 indicated an increase of the plutonium solubility of 22 to 96 times higher. In order to check the influence of organic fertilizers on the solubility of plutonium, a solubility test was carried out using cow urine as extracting solution. The results show that the solubility of plutonium can reach a value equal to 14%, which is similar to the one obtained with sodium pyrophosphate acting as extracting solution. Thus, these results are a clear warning of what might happen if organic fertilizers are used in transuranic-contaminated soils. (author)

Treatment of plutonium process residues by molten salt oxidation

Energy Technology Data Exchange (ETDEWEB)

Stimmel, J.; Wishau, R.; Ramsey, K.B.; Montoya, A.; Brock, J. [Los Alamos National Lab., NM (United States); Heslop, M. [Naval Surface Warfare Center (United States). Indian Head Div.; Wernly, K. [Molten Salt Oxidation Corp. (United States)

1999-04-01

Molten Salt Oxidation (MSO) is a thermal process that can remove more than 99.999% of the organic matrix from combustible {sup 238}Pu material. Plutonium processing residues are injected into a molten salt bed with an excess of air. The salt (sodium carbonate) functions as a catalyst for the conversion of the organic material to carbon dioxide and water. Reactive species such as fluorine, chlorine, bromine, iodine, sulfur, phosphorous and arsenic in the organic waste react with the molten salt to form the corresponding neutralized salts, NaF, NaCl, NaBr, NaI, Na{sub 2}SO{sub 4}, Na{sub 3}PO{sub 4} and NaAsO{sub 2} or Na{sub 3}AsO4. Plutonium and other metals react with the molten salt and air to form metal salts or oxides. Saturated salt will be recycled and aqueous chemical separation will be used to recover the {sup 238}Pu. The Los Alamos National Laboratory system, which is currently in the conceptual design stage, will be scaled down from current systems for use inside a glovebox.

Treatment of plutonium process residues by molten salt oxidation

International Nuclear Information System (INIS)

Stimmel, J.; Wishau, R.; Ramsey, K.B.; Montoya, A.; Brock, J.; Heslop, M.

1999-01-01

Molten Salt Oxidation (MSO) is a thermal process that can remove more than 99.999% of the organic matrix from combustible 238 Pu material. Plutonium processing residues are injected into a molten salt bed with an excess of air. The salt (sodium carbonate) functions as a catalyst for the conversion of the organic material to carbon dioxide and water. Reactive species such as fluorine, chlorine, bromine, iodine, sulfur, phosphorous and arsenic in the organic waste react with the molten salt to form the corresponding neutralized salts, NaF, NaCl, NaBr, NaI, Na 2 SO 4 , Na 3 PO 4 and NaAsO 2 or Na 3 AsO4. Plutonium and other metals react with the molten salt and air to form metal salts or oxides. Saturated salt will be recycled and aqueous chemical separation will be used to recover the 238 Pu. The Los Alamos National Laboratory system, which is currently in the conceptual design stage, will be scaled down from current systems for use inside a glovebox

Plutonium

International Nuclear Information System (INIS)

Koelzer, W.

1989-03-01

This report contains with regard to 'plutonium' statements on chemistry, occurrence and reactions in the environment, handling procedures in the nuclear fuel cycle, radiation protection methods, biokinetics, toxicology and medical treatment to make available reliable data for the public discussion on plutonium especially its use in nuclear power plants and its radiological assessment. (orig.) [de

Plutonium

International Nuclear Information System (INIS)

Mueller-Christiansen, K.; Wollesen, M.

1979-01-01

As emotions and fear of plutonium are neither useful for the non-professionals nor for the political decision makers and the advantages and disadvantages of plutonium can only put against each other under difficulties, the paper wants to present the most essential scientific data of plutonium in a generally understandable way. Each of the individual sections is concluded and they try to give an answer to the most discussed questions. In order to make understanding easier, the scientific facts are only brought at points where it cannot be done without for the correctness of the presentation. Many details were left out knowingly. On the other hand, important details are dealt with several times if it seems necessary for making the presentation correct. The graphical presentations and the figures in many cases contain more than said in the text. They give the interested reader hints to scientific-technical coherences. The total material is to enable the reader to form his own opinion on plutonium problems which are being discussed in public. (orig./HP) [de

THE DEACTIVATION, DECONTAMINATION AND DECOMMISSIONING OF THE PLUTONIUM FINISHING PLANT, A FORMER PLUTONIUM PROCESSING FACILITY AT DOE'S HANFORD SITE

International Nuclear Information System (INIS)

CHARBONEAU, S.L.

2006-01-01

The Plutonium Finishing Plant (PFP) was constructed as part of the Manhattan Project during World War II. The Manhattan Project was developed to usher in the use of nuclear weapons to end the war. The primary mission of the PFP was to provide plutonium used as special nuclear material (SNM) for fabrication of nuclear devices for the war effort. Subsequent to the end of World War II, the PFP's mission expanded to support the Cold War effort through plutonium production during the nuclear arms race and later the processing of fuel grade mixed plutonium-uranium oxide to support DOE's breeder reactor program. In October 1990, at the close of the production mission for PFP, a shutdown order was prepared by the Department of Energy (DOE) in Washington,; DC--and issued to the Richland DOE field office. Subsequent to the shutdown order, a team from the Defense Nuclear Facilities Safety Board (DNFSB) analyzed the hazards at PFP associated with the continued storage of certain forms of plutonium solutions and solids. The assessment identified many discrete actions that were required to stabilize the different plutonium forms into stable form and repackage the material in high integrity containers. These actions were technically complicated and completed as part of the PFP nuclear material stabilization project between 1995 and early 2005. The completion of the stabilization project was a necessary first step in deactivating PFP. During stabilization, DOE entered into negotiations with the U.S. Environmental Protection Agency (EPA) and the State of Washington and established milestones for the Deactivation and Decommissioning (DandD) of the PFP. The DOE and its contractor, Fluor Hanford (Fluor), have made great progress in deactivating, decontaminating and decommissioning the PFP at the Hanford Site as detailed in this paper. Background information covering the PFP DandD effort includes descriptions of negotiations with the State of Washington concerning consent

DOE plutonium disposition study: Analysis of existing ABB-CE Light Water Reactors for the disposition of weapons-grade plutonium. Final report

Energy Technology Data Exchange (ETDEWEB)

1994-06-01

Core reactivity and basic fuel management calculations were conducted on the selected reactors (with emphasis on the System 80 units as being the most desirable choice). Methods used were identical to those reported in the Evolutionary Reactor Report. From these calculations, the basic mission capability was assessed. The selected reactors were studied for modification, such as the addition of control rod nozzles to increase rod worth, and internals and control system modifications that might also be needed. Other system modifications studied included the use of enriched boric acid as soluble poison, and examination of the fuel pool capacities. The basic geometry and mechanical characteristics, materials and fabrication techniques of the fuel assemblies for the selected existing reactors are the same as for System 80+. There will be some differences in plutonium loading, according to the ability of the reactors to load MOX fuel. These differences are not expected to affect licensability or EPA requirements. Therefore, the fuel technology and fuel qualification sections provided in the Evolutionary Reactor Report apply to the existing reactors. An additional factor, in that the existing reactor availability presupposes the use of that reactor for the irradiation of Lead Test Assemblies, is discussed. The reactor operating and facility licenses for the operating plants were reviewed. Licensing strategies for each selected reactor were identified. The spent fuel pool for the selected reactors (Palo Verde) was reviewed for capacity and upgrade requirements. Reactor waste streams were identified and assessed in comparison to uranium fuel operations. Cost assessments and schedules for converting to plutonium disposition were estimated for some of the major modification items. Economic factors (incremental costs associated with using weapons plutonium) were listed and where possible under the scope of work, estimates were made.

Combined evaluation. Plutonium transports in France. Problems of safety and reliability of transport container FS47

International Nuclear Information System (INIS)

Marignac, Y.; Coeytaux, X.; Large, J.H.

2004-09-01

This report concerns the safety and the protection of plutonium dioxide transported from Cogema La Hague to the mixed oxide fuel plant of Marcoule and Cadarache. The French approach of the transport safety is based on the combining of two essential principles: the first one affirms that the performances of the FS47 container in regard of containment (norms TS-R-1 from IAEA for the accidental conditions) is conceived to resist in any situation even terrorism or sabotage. In fact, the IAEA norm follows a probabilistic study without a voluntary attack such a terrorist one. The second principle rests on the ability to prevent the treat of terrorism acts, because of a secrecy policy on the plutonium transport. It appeared that the Green peace association has succeeded several times to know exactly the hours, the trips of the plutonium transport and this simple thing raises more questions than it solves. (N.C.)

PRODUCTION OF PLUTONIUM METAL

Science.gov (United States)

Lyon, W.L.; Moore, R.H.

1961-01-17

A process is given for producing plutonium metal by the reduction of plutonium chloride, dissolved in alkali metal chloride plus or minus aluminum chloride, with magnesium or a magnesium-aluminum alloy at between 700 and 800 deg C and separating the plutonium or plutonium-aluminum alloy formed from the salt.

Plutonium storage phenomenology

International Nuclear Information System (INIS)

Szempruch, R.

1995-12-01

Plutonium has been produced, handled, and stored at Department of Energy (DOE) facilities since the 1940s. Many changes have occurred during the last 40 years in the sources, production demands, and end uses of plutonium. These have resulted in corresponding changes in the isotopic composition as well as the chemical and physical forms of the processed and stored plutonium. Thousands of ordinary food pack tin cans have been used successfully for many years to handle and store plutonium. Other containers have been used with equal success. This paper addressees the exceptions to this satisfactory experience. To aid in understanding the challenges of handling plutonium for storage or immobilization the lessons learned from past storage experience and the necessary countermeasures to improve storage performance are discussed

Simultaneous determination of uranium and plutonium in dissolver solution of irradiated fuel, using ID-TIMS. IRP-11

International Nuclear Information System (INIS)

Shah, Raju; Sasi Bhushan, K.; Govindan, R.; Alamelu, D.; Khodade, P.S.; Aggarwal, S.K.

2007-01-01

A simple sample preparation and simultaneous analysis method to determine uranium and plutonium from dissolver solution, employing the technique of Isotope Dilution Mass spectrometry has been demonstrated. The method used, co-elusion of Uranium and Plutonium from anion exchanger column after initial elution of major part of uranium in 1:5 HNO 3 in order to reduce the initial U/Pu ratio from 1000 to about 100-200 in the co-eluted fraction. Due to the availability of variable multi-collector system, different Faraday cups were adjusted to collect the different ion intensities corresponding to the different masses, during the simultaneous analysis of Uranium and Plutonium, loaded on Re double filament assembly. 233 U and PR grade Plutonium were used as spikes to determine Uranium and Plutonium from dissolver solution of irradiated fuel from research reactor. The possibility of getting the isotopic composition of uranium from the simultaneous analysis of co-eluted purified fraction of U and Pu from spiked aliquots is also explained. (author)

Plutonium controversy

International Nuclear Information System (INIS)

Richmond, C.R.

1980-01-01

The toxicity of plutonium is discussed, particularly in relation to controversies surrounding the setting of radiation protection standards. The sources, amounts of, and exposure pathways of plutonium are given and the public risk estimated

Disposition of plutonium as non-fertile fuel for water reactors

International Nuclear Information System (INIS)

Chidester, K.; Eaton, S.L.; Ramsey, K.B.

1998-01-01

This is the final report of a three-year, Laboratory Directed Research and Development (LDRD) project at the Los Alamos National Laboratory (LANL). The original intent of this project was to investigate the possible use of a new fuel form as a means of dispositioning the declared surplus inventory of weapons-grade plutonium. The focus soon changed, however, to managing the larger and rapidly growing inventories of plutonium arising in commercial spent nuclear fuel through implementation of a new fuel form in existing nuclear reactors. LANL embarked on a parallel path effort to study fuel performance using advanced physics codes, while also demonstrating the ability to fabricate a new fuel form using standard processes in LANL's Plutonium Facility. An evolutionary fuel form was also examined which could provide enhanced performance over standard fuel forms, but which could be implemented in a much shorter time frame than a completely new fuel form. Recent efforts have focused on implementation of results into global energy models and development of follow-on funding to continue this research

Perspective on plutonium

International Nuclear Information System (INIS)

Sun, L.S.

1993-01-01

This paper is intended as a brief overview on the element plutonium. Plutonium is the first primarily man-made element to play a significant role not only in technological development, but also in the economic growth of many countries. The importance of plutonium centers around its enormous energy making it ideal for wide-scale use in reactors, while the nuclear industry continues to work toward improving safety and efficiency of plutonium as a reactor fuel politicians and the public still debate over the safety and benefits of nuclear power. (30 refs.)

Benchmark Specification for an HTR Fuelled with Reactor-grade Plutonium (or Reactor-grade Pu/Th and U/Th). Proposal version 2

International Nuclear Information System (INIS)

Hosking, J.G.; Newton, T.D.; Morris, P.

2007-01-01

This benchmark proposal builds upon that specified in NEA/NSC/DOC(2003)22 report. In addition to the three phases described in that report, another two phases have now been defined. Additional items for calculation have also been added to the existing phases. It is intended that further items may be added to the benchmark after consultation with its participants. Although the benchmark is specifically designed to provide inter-comparisons for plutonium- and thorium-containing fuels, it is proposed that phases considering simple calculations for a uranium fuel cell and uranium core be included. The purpose of these is to identify any increased uncertainties, relative to uranium fuel, associated with the lesser-known fuels to be investigated in different phases of this benchmark. The first phase considers an infinite array of fuel pebbles fuelled with uranium fuel. Phase 2 considers a similar array of pebbles but for plutonium fuel. Phase 3 continues the plutonium fuel inter-comparisons within the context of whole core calculations. Calculations for Phase 4 are for a uranium-fuelled core. Phase 5 considers an infinite array of pebbles containing thorium. In setting the benchmark the requirements in the definition of the LEUPRO-12 PROTEUS benchmark have been considered. Participants were invited to submit both deterministic results as well as, where appropriate, results from Monte Carlo calculations. Fundamental nuclear data, Avogadro's number, natural abundance data and atomic weights have been taken from the references indicated in the document

Plutonium concentrations in airborne soil at Rocky Flats and Hanford determined during resuspension experiments

International Nuclear Information System (INIS)

Sehmel, G.A.

1978-01-01

Plutonium resuspension results are summarized for experiments conducted by the author at Rocky Flats, onsite on the Hanford reservation, and for winds blowing from offsite onto the Hanford reservation near the Prosser barricade boundary. In each case, plutonium resuspension was shown by increased airborne plutonium concentrations as a function of either wind speed or as compared to fallout levels. All measured airborne concentrations were far below maximum permissible concentrations (MPC). Both plutonium and cesium concentrations on airborne soil were normalized by the quantity of airborne soil sampled. Airborne radionuclide concentrations in μCi/g were related to published values for radionuclide concentrations on surface soils. For this ratio of radionuclide concentration per gram on airborne soil divided by that for ground surface soil, there are eight orders of magnitude uncertainty from 10 -4 to 10 4 . This uncertainty in the equality between plutonium concentrations per gram on airborne and surface soils is caused by only a fraction of the collected airborne soil being transported from offsite rather than all being resuspended from each study site and also by the great variabilities in surface contamination. Horizontal plutonium fluxes on airborne nonrespirable soils at all three sites were bracketed within the same four orders of magnitude from 10 -7 to 10 -3 μCi/(m 2 day) for 239 Pu and 10 -8 to 10 -5 μCi/(m 2 day) for 238 Pu. Airborne respirable 239 Pu concentrations increased with wind speed for a southwest wind direction coming from offsite near the Hanford reservation Prosser barricade. Airborne plutonium fluxes on nonrespirable particles had isotopic ratios, 240 Pu/ 239 240 Pu, similar to weapons grade plutonium rather than fallout plutonium

Process for the preparation of uranium dioxide

International Nuclear Information System (INIS)

Watt, G.W.; Baugh, D.W. Jr.

1977-01-01

An actinide dioxide, e.g., uranium dioxide, plutonium dioxide, neptunium dioxide, etc., is prepared by reacting the actinide nitrate hexahydrate with sodium dithionite as a first step; the reaction product from this first step is a novel composition of matter comprising the actinide sulfite tetrahydrate. The reaction product resulting from this first step is then converted to the actinide dioxide by heating it in the absence of an oxygen-containing atmosphere (e.g., nitrogen) to a temperature of about 500 0 to about 950 0 C for about 15 to about 135 minutes. If the reaction product resulting from the first step is, prior to carrying out the second heating step, exposed to an oxygen-containing atmosphere such as air, the resultant product is a novel composition of matter comprising the actinide oxysulfite tetrahydrate which can also be readily converted to the actinide dioxide by heating it in the absence of an oxygen-containing atmosphere (e.g., nitrogen) at a temperature of about 400 0 to about 900 0 C for about 30 to about 150 minutes. Further, the actinide oxysulfite tetrahydrate can be partially dehydrated at reduced pressures (and in the presence of a suitable dehydrating agent such as phosphorus pentoxide). The partially dehydrated product may be readily converted to the dioxide form by heating it in the absence of an oxygen-containing atmosphere (e.g., nitrogen) at a temperature of about 500 0 to about 900 0 C for about 30 to about 150 minutes. 16 claims

Plutonium controversy

Energy Technology Data Exchange (ETDEWEB)

Richmond, C.R.

1980-01-01

The toxicity of plutonium is discussed, particularly in relation to controversies surrounding the setting of radiation protection standards. The sources, amounts of, and exposure pathways of plutonium are given and the public risk estimated. (ACR)

Plutonium, nuclear fuel; Le plutonium, combustible nucleaire

Energy Technology Data Exchange (ETDEWEB)

Grison, E [Commissariat a l' Energie Atomique, Fontenay aux Roses (France). Centre d' Etudes Nucleaires, Saclay

1960-07-01

A review of the physical properties of metallic plutonium, its preparation, and the alloys which it forms with the main nuclear metals. Appreciation of its future as a nuclear fuel. (author) [French] Apercu sur les proprietes physiques du plutonium metallique, sa preparation, ses alliages avec les principaux metaux nucleaires. Consideration sur son avenir en tant que combustible nucleaire. (auteur)

Determination of uranium and plutonium in metal conversion products from electrolytic reduction process

International Nuclear Information System (INIS)

Lee, Chang Heon; Suh, Moo Yul; Joe, Kih Soo; Sohn, Se Chul; Jee, Kwang Young; Kim, Won Ho

2005-01-01

Chemical characterization of process materials is required for the optimization of an electrolytic reduction process in which uranium dioxide, a matrix of spent PWR fuels, is electrolytically reduced to uranium metal in a medium of LiCl-Li 2 O molten at 650 .deg. C. A study on the determination of fissile materials in the uranium metal products containing corrosion products, fission products and residual process materials has been performed by controlled-potential coulometric titration which is well known in the field of nuclear science and technology. Interference of Fe, Ni, Cr and Mg (corrosion products), Nd (fission product) and LiCl molten salt (residual process material) on the determination of uranium and plutonium, and the necessity of plutonium separation prior to the titration are discussed in detail. Under the analytical condition established already, their recovery yields are evaluated along with analytical reliability

Survey of Worldwide Light Water Reactor Experience with Mixed Uranium-Plutonium Oxide Fuel

Energy Technology Data Exchange (ETDEWEB)

Cowell, B.S.; Fisher, S.E.

1999-02-01

The US and the Former Soviet Union (FSU) have recently declared quantities of weapons materials, including weapons-grade (WG) plutonium, excess to strategic requirements. One of the leading candidates for the disposition of excess WG plutonium is irradiation in light water reactors (LWRs) as mixed uranium-plutonium oxide (MOX) fuel. A description of the MOX fuel fabrication techniques in worldwide use is presented. A comprehensive examination of the domestic MOX experience in US reactors obtained during the 1960s, 1970s, and early 1980s is also presented. This experience is described by manufacturer and is also categorized by the reactor facility that irradiated the MOX fuel. A limited summary of the international experience with MOX fuels is also presented. A review of MOX fuel and its performance is conducted in view of the special considerations associated with the disposition of WG plutonium. Based on the available information, it appears that adoption of foreign commercial MOX technology from one of the successful MOX fuel vendors will minimize the technical risks to the overall mission. The conclusion is made that the existing MOX fuel experience base suggests that disposition of excess weapons plutonium through irradiation in LWRs is a technically attractive option.

Survey of Worldwide Light Water Reactor Experience with Mixed Uranium-Plutonium Oxide Fuel

International Nuclear Information System (INIS)

Cowell, B.S.; Fisher, S.E.

1999-01-01

The US and the Former Soviet Union (FSU) have recently declared quantities of weapons materials, including weapons-grade (WG) plutonium, excess to strategic requirements. One of the leading candidates for the disposition of excess WG plutonium is irradiation in light water reactors (LWRs) as mixed uranium-plutonium oxide (MOX) fuel. A description of the MOX fuel fabrication techniques in worldwide use is presented. A comprehensive examination of the domestic MOX experience in US reactors obtained during the 1960s, 1970s, and early 1980s is also presented. This experience is described by manufacturer and is also categorized by the reactor facility that irradiated the MOX fuel. A limited summary of the international experience with MOX fuels is also presented. A review of MOX fuel and its performance is conducted in view of the special considerations associated with the disposition of WG plutonium. Based on the available information, it appears that adoption of foreign commercial MOX technology from one of the successful MOX fuel vendors will minimize the technical risks to the overall mission. The conclusion is made that the existing MOX fuel experience base suggests that disposition of excess weapons plutonium through irradiation in LWRs is a technically attractive option

Fuel Cycle Impacts of Uranium-Plutonium Co-extraction

International Nuclear Information System (INIS)

Taiwo, Temitope; Szakaly, Frank; Kim, Taek-Kyum; Hill, Robert

2008-01-01

A systematic investigation of the impacts of uranium and plutonium co-extraction during fuel separations on reactor performance and fuel cycle has been performed. Proliferation indicators, critical mass and radiation source levels of the separation products or fabricated fuel, were also evaluated. Using LWR-spent-uranium-based MOX fuel instead of natural-uranium-based fuel in a PWR MOX core requires a higher initial plutonium content (∼1%), and results in higher Np-237 content (factor of 5) in the spent fuel, and less consumption of Pu-238 (20%) and Am-241 (14%), indicating a reduction in the effective repository space utilization. Additionally, minor actinides continue to accumulate in the fuel cycle, and thus a separate solution is required for them. Differences were found to be quite smaller (∼0.4% in initial transuranics) between the equilibrium cycles of advanced fast reactor cores using spent and depleted uranium for make-up, in additional to transuranics. The critical masses of the co-extraction products were found to be higher than for weapons-grade plutonium (WG-Pu) and the decay heat and radiation sources of the materials (products) were also found to be generally higher than for WG-Pu in the transuranics content range of 10% to 100% in the heavy-metal. (authors)

Plutonium storage criteria

Energy Technology Data Exchange (ETDEWEB)

Chung, D. [Scientech, Inc., Germantown, MD (United States); Ascanio, X. [Dept. of Energy, Germantown, MD (United States)

1996-05-01

The Department of Energy has issued a technical standard for long-term (>50 years) storage and will soon issue a criteria document for interim (<20 years) storage of plutonium materials. The long-term technical standard, {open_quotes}Criteria for Safe Storage of Plutonium Metals and Oxides,{close_quotes} addresses the requirements for storing metals and oxides with greater than 50 wt % plutonium. It calls for a standardized package that meets both off-site transportation requirements, as well as remote handling requirements from future storage facilities. The interim criteria document, {open_quotes}Criteria for Interim Safe Storage of Plutonium-Bearing Solid Materials{close_quotes}, addresses requirements for storing materials with less than 50 wt% plutonium. The interim criteria document assumes the materials will be stored on existing sites, and existing facilities and equipment will be used for repackaging to improve the margin of safety.

Toxicology of plutonium

International Nuclear Information System (INIS)

Bair, W.J.

1974-01-01

Data are reviewed from studies on the toxicity of Pu in experimental animals. Of the several plutonium isotopes, only 238 Pu and 239 Pu have been studied well. Sufficient results have been obtained to show that the behavior of 238 Pu in biological systems and the resulting biological effects cannot be precisely predicted from studies of 239 Pu. This probably applies also to other radiologically important plutonium isotopes which have half-lives ranging from 45 days to 10 7 years and decay by β-emission, electron capture, and spontaneous fission, as well as by emission of α-particles. All the biological effects of plutonium described in this review are attributed to alpha-particle radiation emitted by the plutonium. However, since plutonium is a chemically active heavy metal, one cannot ignore the possibility of chemical toxicity of the low-specific-activity isotopes, 239 Pu, 242 Pu, and 244 Pu. The preponderance of our knowledge of plutonium toxicology has come from short-term studies of relatively high dosage levels in several animal species. The consequences of high-level internal exposures can be predicted with confidence in experimental animals and probably also in man. However, considering the care with which plutonium is handled in the nuclear industry, a high-level contamination event is unlikely. Considerably less is known about the long-term effects of low levels of contamination. (250 references) (U.S.)

Cycle downstream: the plutonium question; Aval du cycle la question du plutonium

Energy Technology Data Exchange (ETDEWEB)

Zask, G [Electricite de France, EDF/DAC, 75 - Paris (France); Rome, M [Electricite de France, EDF, Service Etudes et Projets Thermiques et Nucleaires, 92 - Courbevoie (France); Delpech, M [CEA Cadarache, Dept. d' Etudes des Reacteurs/SPRC, 13 - Saint-Paul-lez-Durance (France); and others

1998-06-29

This day, organized by the SFEN, took place at Paris the 4 june 1998. Nine papers were presented. They take stock on the plutonium physics and its utilization as a nuclear fuel. This day tried to bring information to answer the following questions: do people have to keep the plutonium in the UOX fuel or in the MOX fuel in order to use it for future fast reactors? Do people have to continue obstinately the plutonium reprocessing in the MOX for the PWR type reactors? Will it be realized a underground disposal? Can it be technically developed plutonium incinerators and is it economically interesting? The plutonium physics, the experimental programs and the possible solutions are presented. (A.L.B.)

The handling of plutonium hexafluoride (1962); Manipulation de l'hexafluorure de plutonium (1962)

Energy Technology Data Exchange (ETDEWEB)

Berard, Ph [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1961-11-15

The major problem posed in this work is the instability of plutonium hexafluoride. The influence of various factors on the decomposition of the fluoride has been studied: physical aspect of the walls, nature of the metal and its pretreatment, influence of the temperature. A means of detecting plutonium-239 in a metallic apparatus by {gamma}-ray counting has been developed; the sensitivity is of the order of half a milligram, but the precision is very low (about 50 per cent). Yields of over 95 per cent have been obtained for the transfer of plutonium during the preparation and sublimation of the hexafluoride. This study confirms the possibility of using plutonium hexafluoride for the extraction of plutonium from irradiated fuel elements by a dry method. (author) [French] Le probleme majeur de cette etude a ete l'instabilite de l'hexafluorure de plutonium. Nous avons etudie l'influence de divers facteurs sur la decomposition de l'hexafluorure: aspect physique des parois, nature du metal et de son pretraitement, influence de la temperature. Nous avons mis au point un mode de detection du plutonium-239 dans un appareillage metallique par comptage du rayonnement {gamma}; la sensibilite est de l'ordre du demi-milligramme, mais la precision est tres faible (50 pour cent environ). Nous avons obtenu des rendements depassant 95 pour cent dans le transfert du plutonium au cours de la fabrication et de la sublimation de l'hexafluorure. Cette etude confirme la possibilite d'utiliser l'hexafluorure de plutonium dans l'extraction du plutonium des combustibles irradies par voie seche. (auteur)

Plutonium re-cycle in HTR

Energy Technology Data Exchange (ETDEWEB)

Desoisa, J. A.

1974-03-15

The study of plutonium cycles in HTRs using reprocessed plutonium from Magnox and AGR fuel cycles has shown that full core plutonium/uranium loadings are in general not feasible, burn-up is limited due the need for lower loadings of plutonium to meet reload core reactivity limits, on-line refueling is not practicable due to the need for higher burnable poison loadings, and low conversion rates in the plutonium-uranium cycles cannot be mitigated by axial loading schemes so that fissile make-up is needed if HTR plutonium recycle is desired.

Plutonium concentrations in airborne soil at Rocky Flats and Hanford determined during resuspension experiments

Energy Technology Data Exchange (ETDEWEB)

Sehmel, G.A.

1978-01-01

Plutonium resuspension results are summarized for experiments conducted by the author at Rocky Flats, onsite on the Hanford reservation, and for winds blowing from offsite onto the Hanford reservation near the Prosser barricade boundary. In each case, plutonium resuspension was shown by increased airborne plutonium concentrations as a function of either wind speed or as compared to fallout levels. All measured airborne concentrations were far below maximum permissible concentrations (MPC). Both plutonium and cesium concentrations on airborne soil were normalized by the quantity of airborne soil sampled. Airborne radionuclide concentrations in ..mu..Ci/g were related to published values for radionuclide concentrations on surface soils. For this ratio of radionuclide concentration per gram on airborne soil divided by that for ground surface soil, there are eight orders of magnitude uncertainty from 10/sup -4/ to 10/sup 4/. This uncertainty in the equality between plutonium concentrations per gram on airborne and surface soils is caused by only a fraction of the collected airborne soil being transported from offsite rather than all being resuspended from each study site and also by the great variabilities in surface contamination. Horizontal plutonium fluxes on airborne nonrespirable soils at all three sites were bracketed within the same four orders of magnitude from 10/sup -7/ to 10/sup -3/ ..mu..Ci/(m/sup 2/ day) for /sup 239/Pu and 10/sup -8/ to 10/sup -5/ ..mu..Ci/(m/sup 2/ day) for /sup 238/Pu. Airborne respirable /sup 239/Pu concentrations increased with wind speed for a southwest wind direction coming from offsite near the Hanford reservation Prosser barricade. Airborne plutonium fluxes on nonrespirable particles had isotopic ratios, /sup 240/Pu//sup 239/ /sup 240/Pu, similar to weapons grade plutonium rather than fallout plutonium.

PLUTONIUM-ZIRCONIUM ALLOYS

Science.gov (United States)

Schonfeld, F.W.; Waber, J.T.

1960-08-30

A series of nuclear reactor fuel alloys consisting of from about 5 to about 50 at.% zirconium (or higher zirconium alloys such as Zircaloy), balance plutonium, and having the structural composition of a plutonium are described. Zirconium is a satisfactory diluent because it alloys readily with plutonium and has desirable nuclear properties. Additional advantages are corrosion resistance, excellent fabrication propenties, an isotropie structure, and initial softness.

Optimization and plutonium equilibrium

International Nuclear Information System (INIS)

Silver, G.L.

1976-01-01

The sequential simplex method has been used to estimate the extent of disproportionation of tetravalent plutonium in dilute acid. A method for simulating potentiometric titrations is proposed, and this method suggests that the stoichiometric end point and the inflection point may not always correspond in the potentiometric titration of plutonium. A possible characteristic equation for the nitrite-plutonium reaction is illustrated, and the method of proportional equations is extended to the iron-plutonium reaction

Assesment of Plutonium 238 and Plutonium 239+240 in soils of different agricultural regions of Guatemala

International Nuclear Information System (INIS)

Gutierrez Martinez, E.A.

1998-02-01

In this report an assesment and measurement of PLUTONIUM 238, PLUTONIUM 239, and PLUTONIUM 240 are made. Samples of cultivated soils in 15 provinces of Guatemala were taken. To separate plutonium isotopes a radiochemical method was made using extraction, precipitation and ionic interchange. By electrodeposition the plutonium was measured using an alpha spectroscopy by PIPS method. The radioactivity ranges from 2.84 mBq/Kg to 36.38 mBq/Kg for plutonium 238, and 8.46 mBq/Kg to 26.61 mBq/Kg for plutonium 239+240

Plutonium roundtable discussion

International Nuclear Information System (INIS)

Penneman, R.A.

1982-01-01

The roundtable discussion began with remarks by the chairman who pointed out the complicated nature of plutonium chemistry. Judging from the papers presented at this symposium, he noticed a pattern which indicated to him the result of diminished funding for investigation of basic plutonium chemistry and funding focused on certain problem areas. Dr. G.L. silver pointed to plutonium chemists' erroneous use of a simplified summary equation involving the disproportionation of Pu(EV) and their each of appreciation of alpha coefficients. To his appreciation of alpha coefficients. To his charges, Dr. J.T. Bell spoke in defense of the chemists. This discussion was followed by W.W. Schulz's comments on the need for experimental work to determine solubility data for plutonium in its various oxidation states under geologic repository conditions. Discussion then turned to plutonium pyrachemical process with Dana C. Christensen as the main speaker. This paper presents edited versions of participants' written version

Non-fertile fuels for burning weapons plutonium in thermal fission reactors

International Nuclear Information System (INIS)

Lombardi, C.; Mazzola, A.; Vettraino, F.

1996-01-01

In the last few years, the excess plutonium disposition has become ever more a topical and critical issue. As a matter of fact, more than 200 MT of plutonium coming from spent fuel reprocessing have been already stockpiled and over the next decade, under the already ratified agreements, another about 200 MT of weapon-grade plutonium are expected to be available from nuclear weapons dismantlement. On this basis, an ever growing plutonium production is no longer the goal and the already stored quantities should be burnt in power reactors by taking care that no new plutonium is generated under irradiation. This new outlook in considering plutonium has led many designers to reassess the Fast Breeder Reactors (FBR) role and shifting from breeder to burner machines perspective. Several solutions for burning plutonium have been so far proposed and discussed from the safeguards, proliferation resistance, environmental safety, technological background, economy and time schedule standpoint. A proposal for plutonium burning in commercial Pressurized Water Reactors (PWR) by using a non-fertile oxide-type fuel consisting of PuO 2 diluted in an inert matrix is reported hereafter. This solution appears to receive an ever growing interest in the nuclear community. In order not to produce new plutonium during irradiation an innovative U-free fuel is being researched, based on an inert matrix which will consist in a mixed compound of inert oxides, such as ZrO 2 , Al2O 3 , MgO, CeO 2 where the plutonium oxide is dispersed in. The matrix will fulfill the following requirements: good chemical compatibility, acceptable thermal conductivity, good nuclear properties, good stability under irradiation, good dissolution resistance. The plutonium relative content will be comparable to that used in MOX fuel. The fuel is expected to be characterized by a high chemical stability (rock-like fuel), so that after discharge from reactor and adequate cooling time, it can be considered a High Level

Integrated safeguards and security for the INEL Special Isotope Separation Plant

International Nuclear Information System (INIS)

Warner, G.F.; Zack, N.R.

1990-01-01

This paper describes the development of the safeguards and security system that was to be used for the Special Isotope Separation (SIS) Production Plant. The US Department of Energy has postponed the construction of the SIS Plant that was to be built at the Idaho National Engineering Laboratory (INEL) site near Idaho Falls, Idaho. The Plant was designed to produce weapons grade plutonium from DOE owned fuel grade plutonium by converting off-spec. plutonium dioxide into metal buttons that would meet required chemical and isotopic specifications. Because this was to be a completely new facility there was a unique opportunity to provide an in-depth, ''state-of-the- art'' safeguards and security system without attempting to overlay upon an existing, older system. This facility was being designed to be in complete compliance with the new DOE Orders by integrating safeguards and security into the plant operating system and by providing graded protection to the areas of varying sensitivity within the plant

Cancer hazard from inhaled plutonium

International Nuclear Information System (INIS)

Gofman, J.W.

1975-01-01

The best estimate of the lung cancer potential in humans for inhaled insoluble compounds of plutonium (such as PuO 2 particles) has been grossly underestimated by such authoritative bodies as the International Commission on Radiological Protection and the British Medical Research Council. Calculations are presented of lung cancer induction by 239 Pu as insoluble particles and for deposited reactor-grade Pu. The reason for the gross underestimate of the carcinogenic effects of Pu by ICRP or the British Medical Research Council (BMRC) is their use of a totally unrealistic idealized model for the clearance of deposited Pu from the lungs and bronchi plus their non-recognition of the bronchi as the true site for most human lung cancers. The erroneous model used by such organizations also fails totally to take into account the effect of cigarette-smoking upon the physiological function of human lungs. Plutonium nuclides, such as 239 Pu, or other alpha particle-emitting nuclides, in an insoluble form represent an inhalation cancer hazard in a class some 100,000 times more potent than the potent chemical carcinogens, weight for weight. The already-existing lung cancer data for beagle dogs inhaling insoluble PuO 2 particles is clearly in order of magnitude agreement with calculations for humans

Diffusion in the uranium - plutonium system and self-diffusion of plutonium in epsilon phase; Diffusion dans le systeme uranium-plutonium et autodiffusion du plutonium epsilon

Energy Technology Data Exchange (ETDEWEB)

Dupuy, M [Commissariat a l' Energie Atomique, Fontenay-Aux-Roses (France). Centre d' Etudes Nucleaires

1967-07-01

A survey of uranium-plutonium phase diagram leads to confirm anglo-saxon results about the plutonium solubility in {alpha} uranium (15 per cent at 565 C) and the uranium one in {zeta} phase (74 per cent at 565 C). Interdiffusion coefficients, for concentration lower than 15 per cent had been determined in a temperature range from 410 C to 640 C. They vary between 0.2 and 6 10{sup 12} cm{sup 2} s{sup -1}, and the activation energy between 13 and 20 kcal/mole. Grain boundary, diffusion of plutonium in a uranium had been pointed out by micrography, X-ray microanalysis and {alpha} autoradiography. Self-diffusion of plutonium in {epsilon} phase (bcc) obeys Arrhenius law: D = 2. 10{sup -2} exp -(18500)/RT. But this activation energy does not follow empirical laws generally accepted for other metals. It has analogies with 'anomalous' bcc metals ({beta}Zr, {beta}Ti, {beta}Hf, U{sub {gamma}}). (author) [French] Une etude du diagramme d'equilibre uranium-plutonium conduit a confirmer les resultats anglo-saxons relatifs a la solubilite du plutonium dans l'uranium {alpha} (15 pour cent a 565 C) et de l'uranium dans la phase {zeta} (74 pour cent a 565 C). Les coefficients de diffusion chimique, pour des concentrations inferieures a 15 pour cent ont ete determines a des temperatures comprises entre 410 et 640 C. Ils se situent entre 0.2 et 6. 10{sup 12} cm{sup 2} s{sup -1}. L'energie d'activation varie entre 13 et 20 kcal/mole. La diffusion intergranulaire du plutonium dans l'uranium a a ete mise en evidence par micrographie, microanalyse X et autoradiographie {alpha}. L' autodiffusion du plutonium {beta} cubique centree obeit a la loi d'Arrhenius D = 2. 10{sup -2} exp - (18500)/RT. Son energie d'activation n'obeit pas aux lois empiriques generalement admises pour les autres metaux. Elle possede des analogies avec les cubiques centres ''anormaux'' (Zr{beta}, Ti{beta}, Hf{beta}, U{gamma}). (auteur)

Initial data report in response to the surplus plutonium disposition environmental impact statement data call for the UO2 supply. Revision 1

International Nuclear Information System (INIS)

White, V.S.; Cash, J.M.; Michelhaugh, R.D.

1997-11-01

The purpose of this document is to support the US Department of Energy (DOE) Fissile Materials Disposition Program's preparation of the draft Surplus Plutonium Disposition Environmental Impact Statement. This is one of several responses to data calls generated to provide background information on activities associated with the operation of the Mixed-Oxide (MOX) Fuel Fabrication Facility. Urania feed for the MOX Fuel Fabrication Facility may be either natural or depleted. Natural uranium typically contains 0.0057 wt% 234 U, 0.711 wt% 235 U, and the majority as 238 U. The fissile isotope is 235 U, and uranium is considered depleted if the total 235 U content is less than 0.711 wt% as found in nature. The average composition of 235 U in DOE's total depleted urania inventory is 0.20 wt%. The depleted uranium assay range proposed for use in this program is 0.2500--0.2509 wt%. Approximately 30% more natural uranium would be required than depleted uranium based on the importance of maintaining a specific fissile portion in the MOX fuel blend. If the uranium component constitutes a larger quantity of fissile material, less plutonium can be dispositioned on an annual basis. The percentage composition, referred to as assay, of low-enriched uranium necessary for controlled fission in commercial light-water nuclear power reactors is 1.8--5.0 wt% 235 U. This data report provides information on the schedule, acquisition, impacts, and conversion process for using uranium, derived from depleted uranium hexafluoride (UF 6 ), as the diluent for the weapons-grade plutonium declared as surplus. The case analyzed is use of depleted UF 6 in storage at the Portsmouth Gaseous Diffusion Plant in Piketon, Ohio, being transported to a representative UF 6 to uranium dioxide conversion facility (GE Nuclear Energy) for processing, and subsequently transported to the MOX Fuel Fabrication Facility

Drop-in capsule testing of plutonium-based fuels in the Advanced Test Reactor

International Nuclear Information System (INIS)

Chang, G.S.; Ryskamp, J.M.; Terry, W.K.; Ambrosek, R.G.; Palmer, A.J.; Roesener, R.A.

1996-09-01

The most attractive way to dispose of weapons-grade plutonium (WGPu) is to use it as fuel in existing light water reactors (LWRs) in the form of mixed oxide (MOX) fuel - i.e., plutonia (PuO[sub 2]) mixed with urania (UO[sub 2]). Before U.S. reactors could be used for this purpose, their operating licenses would have to be amended. Numerous technical issues must be resolved before LWR operating licenses can be amended to allow the use of MOX fuel. The proposed weapons-grade MOX fuel is unusual, even relative to ongoing foreign experience with reactor-grade MOX power reactor fuel. Some demonstration of the in- reactor thermal, mechanical, and fission gas release behavior of the prototype fuel will most likely be required in a limited number of test reactor irradiations. The application to license operation with MOX fuel must be amply supported by experimental data. The Advanced Test Reactor (ATR) at the Idaho National Engineering Laboratory (INEL) is capable of playing a key role in the irradiation, development, and licensing of these new fuel types. The ATR is a 250- MW (thermal) LWR designed to study the effects of intense radiation on reactor fuels and materials. For 25 years, the primary role of the ATR has been to serve in experimental investigations for the development of advanced nuclear fuels. Both large- and small-volume test positions in the ATR could be used for MOX fuel irradiation. The ATR would be a nearly ideal test bed for developing data needed to support applications to license LWRs for operation with MOX fuel made from weapons-grade plutonium. Furthermore, these data can be obtained more quickly by using ATR instead of testing in a commercial LWR. Our previous work in this area has demonstrated that it is technically feasible to perform MOX fuel testing in the ATR. This report documents our analyses of sealed drop-in capsules containing plutonium-based test specimens placed in various ATR positions

F. Biological hazards of plutonium

International Nuclear Information System (INIS)

1976-01-01

Plutonium is an unavoidable result of present nuclear power programmes. Its predominant isotopes are extremely long-lived and very toxic if absorbed in the body. In view of the increasing potential for plutonium and man to come into contact, the consequences of any plutonium release into the environment should be scientifically examined. This report is an attempt to place in one document a fully referenced account of the on-going work in many areas. There are three sections. Part 1 deals with the amounts of plutonium available in the fuel cycle, its properties and the probability of routine or accidental release. Part 2 examines the ways in which plutonium can reach man, in particular through food chains or inhalation. Part 3 details the biological effects of plutonium once it is absorbed into the body, assesses the amounts likely to be harmful and discusses the adequacy of present standards for plutonium burdens. There are two appendices. The likely differences between Pu-239, the most studied isotope, and other plutonium isotopes or transuranic nuclides are outlined in Appendix A. Appendix B contains a fuller account of the ways in which the fate of ingested or inhaled plutonium have been determined

Charge distribution on plutonium-containing aerosols produced in mixed-oxide reactor fuel fabrication and the laboratory

International Nuclear Information System (INIS)

Yeh, H.C.; Newton, G.J.; Teague, S.V.

1976-01-01

The inhalation toxicity of potentially toxic aerosols may be affected by the electrostatic charge on the particles. Charge may influence the deposition site during inhalation and therefore its subsequent clearance and dose patterns. The electrostatic charge distributions on plutonium-containing aerosols were measured with a miniature, parallel plate, aerosol electrical mobility spectrometer. Two aerosols were studied: a laboratory-produced 238 PuO 2 aerosol (15.8 Ci/g) and a plutonium mixed-oxide aerosol (PU-MOX, natural UO 2 plus PuO 2 , 0.02 Ci/g) formed during industrial centerless grinding of mixed-oxide reactor fuel pellets. Plutonium-238 dioxide particles produced in the laboratory exhibited a small net positive charge within a few minutes after passing through a 85 Kr discharger due to alpha particle emission removal of valence electrons. PU-MOX aerosols produced during centerless grinding showed a charge distribution essentially in Boltzmann equilibrium. The gross alpha aerosol concentrations (960-1200 nCi/l) within the glove box were sufficient to provide high ion concentrations capable of discharging the charge induced by mechanical and/or nuclear decay processes

Joint U.S./Russian plutonium disposition study: Nonproliferation issues

International Nuclear Information System (INIS)

Jaeger, C.; Erkkila, B.; Fearey, B.; Ehinger, M.; McAllister, S.; Chitaykin, V.; Ptashny, V.

1996-01-01

In an effort to establish joint activities in the disposition of fissile materials from nuclear materials, the US and Russia agreed to conduct joint work to develop consistent comparisons of various alternatives for the disposition of weapons-grade plutonium. Joint working groups were established for the analysis of alternatives for plutonium management for water reactors, fast reactors, storage, geological formations, immobilization and stabilization of solutions and other forms. In addition cross-cutting working groups were established for economic analysis and nonproliferation (NP). This paper reviews the activities of the NP working group in support of these studies. The NP working group provided integrated support in the area of nuclear NP to the other US/Russian Study teams. It involved both domestic safeguards and security and international safeguards. The analysis of NP involved consideration of the resistance to theft or diversion and resistance to retrieval, extraction or reuse

Use of plutonium for power production

International Nuclear Information System (INIS)

1965-01-01

The panel reviewed available information on various aspects of plutonium utilization, such as physics of plutonium, technology of plutonium fuels in thermal and fast reactors, behaviour of plutonium fuel under reactor irradiation, technological and economic aspects of plutonium fuel cycle. Refs, figs and tabs

World status report: plutonium

International Nuclear Information System (INIS)

Dircks, W.

1992-01-01

In a recent speech in Japan, the Deputy Director General of the International Atomic Energy Agency (IAEA) said that the economic case for reprocessing spent nuclear fuel had been severely eroded. An edited version of the speech is given. The changed prospects for nuclear energy is given as the reason why the demand for plutonium has declined sharply. The oil crisis of the 1970s reduced the demand for electric power and the economic justification for the use of recycled plutonium. The stockpile of isolated plutonium is growing rapidly giving rise to worries about its security. From this point of view, isolated plutonium is best kept in reactor fuel not separated out. In this connection the IAEA has offered to help in the storage of plutonium so that vigorous safety and security requirements are met. In Japan there is a debate about the plutonium which is dependent on the future of the fast breeder reactor programme. (UK)

Electron Microscopy Study of Stainless Steel Radiation Damage Due to Long-Term Irradation by Alpha Particles Emitted From Plutonium

Energy Technology Data Exchange (ETDEWEB)

Unlu, Kenan [Univ. of Texas, Austin, TX (United States); Rios-Martinez, Carlos [Univ. of Texas, Austin, TX (United States); Saglam, Mehmet [Univ. of Texas, Austin, TX (United States); Hart, Ron R. [Texas A & M Univ., College Station, TX (United States); Shipp, John D. [Texas A & M Univ., College Station, TX (United States); Rennie, John [Texas A & M Univ., College Station, TX (United States)

1998-04-16

Radiation damage and associated surface and microstructural changes produced in stainless steel encapsulation by high-fluence alpha particle irradiations from weapons-grade plutonium of 316-stainless steel are being investigated.

Plutonium Finishing Plant

Data.gov (United States)

Federal Laboratory Consortium — The Plutonium Finishing Plant, also known as PFP, represented the end of the line (the final procedure) associated with plutonium production at Hanford.PFP was also...

Determination of origin and intended use of plutonium metal using nuclear forensic techniques.

Science.gov (United States)

Rim, Jung H; Kuhn, Kevin J; Tandon, Lav; Xu, Ning; Porterfield, Donivan R; Worley, Christopher G; Thomas, Mariam R; Spencer, Khalil J; Stanley, Floyd E; Lujan, Elmer J; Garduno, Katherine; Trellue, Holly R

2017-04-01

Nuclear forensics techniques, including micro-XRF, gamma spectrometry, trace elemental analysis and isotopic/chronometric characterization were used to interrogate two, potentially related plutonium metal foils. These samples were submitted for analysis with only limited production information, and a comprehensive suite of forensic analyses were performed. Resulting analytical data was paired with available reactor model and historical information to provide insight into the materials' properties, origins, and likely intended uses. Both were super-grade plutonium, containing less than 3% 240 Pu, and age-dating suggested that most recent chemical purification occurred in 1948 and 1955 for the respective metals. Additional consideration of reactor modeling feedback and trace elemental observables indicate plausible U.S. reactor origin associated with the Hanford site production efforts. Based on this investigation, the most likely intended use for these plutonium foils was 239 Pu fission foil targets for physics experiments, such as cross-section measurements, etc. Copyright © 2017 Elsevier B.V. All rights reserved.

Plutonium Immobilization Program cold pour tests

International Nuclear Information System (INIS)

Hovis, G.L.; Stokes, M.W.; Smith, M.E.; Wong, J.W.

1999-01-01

The Plutonium Immobilization Program (PIP) is a joint venture between the Savannah River Site, Lawrence Livermore National Laboratory, Argonne National Laboratory, and Pacific Northwest National Laboratory to carry out the disposition of excess weapons-grade plutonium. This program uses the can-in-canister (CIC) approach. CIC involves encapsulating plutonium in ceramic forms (or pucks), placing the pucks in sealed stainless steel cans, placing the cans in long cylindrical magazines, latching the magazines to racks inside Defense Waste Processing Facility (DWPF) canisters, and filling the DWPF canisters with high-level waste glass. This process puts the plutonium in a stable form and makes it attractive for reuse. At present, the DWPF pours glass into empty canisters. In the CIC approach, the addition of a stainless steel rack, magazines, cans, and ceramic pucks to the canisters introduces a new set of design and operational challenges: All of the hardware installed in the canisters must maintain structural integrity at elevated (molten-glass) temperatures. This suggests that a robust design is needed. However, the amount of material added to the DWPF canister must be minimized to prevent premature glass cooling and excessive voiding caused by a large internal thermal mass. High metal temperatures, minimizing thermal mass, and glass flow paths are examples of the types of technical considerations of the equipment design process. To determine the effectiveness of the design in terms of structural integrity and glass-flow characteristics, full-scale testing will be conducted. A cold (nonradioactive) pour test program is planned to assist in the development and verification of a baseline design for the immobilization canister to be used in the PIP process. The baseline design resulting from the cold pour test program and CIC equipment development program will provide input to Title 1 design for second-stage immobilization. The cold pour tests will be conducted in two

Double shell tanks plutonium inventory assessment

International Nuclear Information System (INIS)

Tusler, L.A.

1995-01-01

This report provides an evaluation that establishes plutonium inventory estimates for all DSTs based on known tank history information, the DST plutonium inventory tracking system, tank characterization measurements, tank transfer records, and estimated average concentration values for the various types of waste. These estimates use data through December 31, 1994, and give plutonium estimates as of January 1, 1995. The plutonium inventory values for the DSTs are given in Section 31. The plutonium inventory estimate is 224 kg for the DSTs and 854 kg for the SSTs for a total of 1078 kg. This value compares favorably with the total plutonium inventory value of 981 kg obtained from the total plutonium production minus plutonium recovery analysis estimates

Determination of plutonium in environment

International Nuclear Information System (INIS)

Sakanoue, Masanobu

1978-01-01

Past and present methods of determining the amount of plutonium in the environment are summarized. Determination of the amount of plutonium in uranium ore began in 1941. Plutonium present in polluted environments due to nuclear explosions, nuclear power stations, etc. was measured in soil and sand in Nagasaki in 1951 and in ash in Bikini in 1954. Analytical methods of measuring the least amount of plutonium in the environment were developed twenty years later. Many studies on and reviews of these methods have been reported all over the world, and a standard analytical procedure has been adopted. A basic analytical method of measurement was drafted in Japan in 1976. The yield, treatment of samples, dissolution, separation, control of measurable ray sources determination by α spectrometry, cross-check determination, and treatment of samples containing hardly soluble plutonium were examined. At present, the amount of plutonium can be determined by all of these methods. The presence of plutonium was studied further, and the usefulness of determination of the plutonium isotope ratio is discussed. (Kumagai, S.)

Plutonium in the marine environment

International Nuclear Information System (INIS)

Jarvis, N.V.; Linder, P.W.; Wade, P.W.

1994-01-01

The shipping of plutonium from Europe to Japan around the Cape is a contentious issue which has raised public concern that South Africa may be at risk to plutonium exposure should an accident occur. The paper describes the containers in which the plutonium (in the form of plutonium oxide, PuO 2 ) is housed and consequences of the unlikely event of these becoming ruptured. Wind-borne pollution is considered not to be a likely scenario, with the plutonium oxide particles more likely to remain practically insoluble and sediment. Plutonium aqueous and environmental chemistry is briefly discussed. Some computer modelling whereby plutonium oxide is brought into contact with seawater has been performed and the results are presented. The impact on marine organisms is discussed in terms of studies performed at marine dump sites and after the crash of a bomber carrying nuclear warheads in Thule, Greenland in 1968. Various pathways from the sea to land are considered in the light of studies done at Sellafield, a reprocessing plant in the United Kingdom. Some recent debates in the popular scientific press, such as that on the leukemia cluster at Sellafield, are described. Plutonium biochemistry and toxicity are discussed as well as medical histories of workers exposed to plutonium. 35 refs., 2 tabs., 1 fig

Evolutionary/advanced light water reactor data report

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-02-09

The US DOE Office of Fissile Material Disposition is examining options for placing fissile materials that were produced for fabrication of weapons, and now are deemed to be surplus, into a condition that is substantially irreversible and makes its use in weapons inherently more difficult. The principal fissile materials subject to this disposition activity are plutonium and uranium containing substantial fractions of plutonium-239 uranium-235. The data in this report, prepared as technical input to the fissile material disposition Programmatic Environmental Impact Statement (PEIS) deal only with the disposition of plutonium that contains well over 80% plutonium-239. In fact, the data were developed on the basis of weapon-grade plutonium which contains, typically, 93.6% plutonium-239 and 5.9% plutonium-240 as the principal isotopes. One of the options for disposition of weapon-grade plutonium being considered is the power reactor alternative. Plutonium would be fabricated into mixed oxide (MOX) fuel and fissioned (``burned``) in a reactor to produce electric power. The MOX fuel will contain dioxides of uranium and plutonium with less than 7% weapon-grade plutonium and uranium that has about 0.2% uranium-235. The disposition mission could, for example, be carried out in existing power reactors, of which there are over 100 in the United States. Alternatively, new LWRs could be constructed especially for disposition of plutonium. These would be of the latest US design(s) incorporating numerous design simplifications and safety enhancements. These ``evolutionary`` or ``advanced`` designs would offer not only technological advances, but also flexibility in siting and the option of either government or private (e.g., utility) ownership. The new reactor designs can accommodate somewhat higher plutonium throughputs. This data report deals solely with the ``evolutionary`` LWR alternative.

Evolutionary/advanced light water reactor data report

International Nuclear Information System (INIS)

1996-01-01

The US DOE Office of Fissile Material Disposition is examining options for placing fissile materials that were produced for fabrication of weapons, and now are deemed to be surplus, into a condition that is substantially irreversible and makes its use in weapons inherently more difficult. The principal fissile materials subject to this disposition activity are plutonium and uranium containing substantial fractions of plutonium-239 uranium-235. The data in this report, prepared as technical input to the fissile material disposition Programmatic Environmental Impact Statement (PEIS) deal only with the disposition of plutonium that contains well over 80% plutonium-239. In fact, the data were developed on the basis of weapon-grade plutonium which contains, typically, 93.6% plutonium-239 and 5.9% plutonium-240 as the principal isotopes. One of the options for disposition of weapon-grade plutonium being considered is the power reactor alternative. Plutonium would be fabricated into mixed oxide (MOX) fuel and fissioned (''burned'') in a reactor to produce electric power. The MOX fuel will contain dioxides of uranium and plutonium with less than 7% weapon-grade plutonium and uranium that has about 0.2% uranium-235. The disposition mission could, for example, be carried out in existing power reactors, of which there are over 100 in the United States. Alternatively, new LWRs could be constructed especially for disposition of plutonium. These would be of the latest US design(s) incorporating numerous design simplifications and safety enhancements. These ''evolutionary'' or ''advanced'' designs would offer not only technological advances, but also flexibility in siting and the option of either government or private (e.g., utility) ownership. The new reactor designs can accommodate somewhat higher plutonium throughputs. This data report deals solely with the ''evolutionary'' LWR alternative

Plutonium Training Opportunities

Energy Technology Data Exchange (ETDEWEB)

Balatsky, Galya Ivanovna [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Wolkov, Benjamin [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-03-26

This report was created to examine the current state of plutonium training in the United States and to discover ways in which to ensure that the next generation of plutonium workers are fully qualified.

Optimizing Plutonium stock management

International Nuclear Information System (INIS)

Niquil, Y.; Guillot, J.

1997-01-01

Plutonium from spent fuel reprocessing is reused in new MOX assemblies. Since plutonium isotopic composition deteriorates with time, it is necessary to optimize plutonium stock management over a long period, to guarantee safe procurement, and contribute to a nuclear fuel cycle policy at the lowest cost. This optimization is provided by the prototype software POMAR

Lixiviation of plutonium contaminated solid wastes by aqueous solution of electro-generated reducing agents

International Nuclear Information System (INIS)

Agarande, Michelle

1991-01-01

This study concerns the development of the new concept for the decontamination of plutonium bearing solid wastes, based on the lixiviation of the wastes using electro-generated reducing agents. First, a comparative study of the kinetics of the dissolution of pure PuO 2 (prepared by calcination of Pu (IV) oxalate at 450 C) in sulfuric acid media, with different reducing agents, was realized. Qualitatively these reagents can be sorted in three groups: 1 / fast kinetics for Cr(II), V(II) and U(III); 2 / slow kinetics for Ti(III); 3 / very slow kinetics for V(III) and U(VI). In order to contribute to the design of an electrochemical reactor for the generation of the reducing agents usable for the lixiviation of plutonium bearing solid wastes, the study of the diffusion coefficients of both oxidized and reduced forms of different redox couples, at different temperatures, was undertaken. The results of this study also permits, from the knowledge of the diffusional activation energy of the ions, to conclude that the dissolution of pure plutonium dioxide under the action of these reducing agents is not diffusion limited. The feasibility of the plutonium decontamination treatment of synthetic or real solid wastes was then studied at laboratory scale using electro-generated V(II), which is with Cr(II) among the best reagents. The efficiency of the treatment was good, (80 pc Pu solubilisation yield), especially in the case of cellulosic or miscellaneous organic wastes. (author) [fr

Oxidation-state distribution of plutonium in surface and subsurface waters at Thule, northwest Greenland

International Nuclear Information System (INIS)

McMahon, C.A.; Leon Vintro, L.; Mitchell, P.I.; Dahlgaard, H.

2000-01-01

The speciation of plutonium in Arctic waters sampled on the northwest Greenland shelf in August 1997 is discussed in this paper. Specifically, we report the results of analyses carried out on seawater sampled (a) close to the Thule air base where, in 1968, a US military aircraft carrying four nuclear weapons crashed on sea ice, releasing kilogram quantities of plutonium to the snow pack and underlying seabed sediments, and (b) at a reference station (Upernavik) located ∼400 km to the south. The data show that most of the plutonium in the dissolved phase at Thule is in the form of Pu(V, VI) (mean: 68±6%; n=6), with little if any distinction apparent between surface and bottom waters. Further, the oxidation state distribution at stations close to the accident site is similar to that measured at Upernavik, remote from this site. It is also similar to the distribution observed in shelf waters at mid-latitudes, suggesting that the underlying processes controlling plutonium speciation are insensitive to temperature over the range 0-25 deg. C. Measurements using tangential-flow ultrafiltration indicate that virtually all of the plutonium (including the fraction in a reduced chemical form) is present as fully dissolved species. Most of this plutonium would seem to be of weapons fallout origin, as the mean 238 Pu/ 239,240 Pu activity ratio in the water column (dissolved phase) at Thule (0.06±0.02; n=10) is similar to the global fallout ratio at this latitude (∼0.04). Thus, there is little evidence of weapons-grade plutonium in the water column at Thule at the present time

Treatment of plutonium contaminations

International Nuclear Information System (INIS)

Lafuma, J.

1983-01-01

Three kinds of plutonium contaminations were considered: skin contamination; contaminated wounds; contamination by inhalation. The treatment of these contaminations was studied for insoluble (oxide and metal forms) and soluble plutonium (complexes). The use of DTPA and therapeutic problems encountered with stable plutonium complexes were analyzed. The new possibilities of internal decontamination using Puchel and LICAM were evaluated [fr

An assessment of the validity of cerium oxide as a surrogate for plutonium oxide gallium removal studies

International Nuclear Information System (INIS)

Kolman, D.G.; Park, Y.; Stan, M.; Hanrahan, R.J. Jr.; Butt, D.P.

1999-01-01

Methods for purifying plutonium metal have long been established. These methods use acid solutions to dissolve and concentrate the metal. However, these methods can produce significant mixed waste, that is, waste containing both radioactive and chemical hazards. The volume of waste produced from the aqueous purification of thousands of weapons would be expensive to treat and dispose. Therefore, a dry method of purification is highly desirable. Recently, a dry gallium removal research program commenced. Based on initial calculations, it appeared that a particular form of gallium (gallium suboxide, Ga 2 O) could be evaporated from plutonium oxide in the presence of a reducing agent, such as small amounts of hydrogen dry gas within an inert environment. Initial tests using ceria-based material (as a surrogate for PuO 2 ) showed that thermally-induced gallium removal (TIGR) from small samples (on the order of one gram) was indeed viable. Because of the expense and difficulty of optimizing TIGR from plutonium dioxide, TIGR optimization tests using ceria have continued. This document details the relationship between the ceria surrogate tests and those conducted using plutonia

Plutonium isotopes in the environment

International Nuclear Information System (INIS)

Holm, E.

1977-12-01

Determination of plutonium and americium by ion exchange and alpha-spectrometry. Deposition of global fall-out and accumulated area-content of 238 Pu, 239 Pu, 240 Pu, 241 Pu, 242 Pu and 241 Am in central Sweden (62.3 deg N, 12.4 deg E), by using the lichen species Cladonia alpestris as bioindicator. Retention and distribution of plutonium in carpets of lichen and soil. Transfer of plutonium from lichen to reindeer and man. Absorbed dose in reindeer and man from plutonium. Basic studies of plutonium and americium in the western Mediterranean surface waters, with emphases on particulate form of the transuranics. (author)

The first metallurgical tests on plutonium; Premiers essais metallurgiques sur le plutonium

Energy Technology Data Exchange (ETDEWEB)

Grison, E; Abramson, R; Anselin, F; Monti, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

Metallic plutonium was first prepared in France in January 1956, as soon as we had access to quantities of the order of several grams of plutonium, which had been extracted from the rods of the pile EL2 at Saclay. Since up to the present this reactor, of thermal power 2 000 kW, has been our only source of plutonium, we have so far only worked on experimental quantities sufficient for the basic tests but not for tests on a scale of possible applications. It is this work, carried out during this phase of preliminary research, which is described below. With the starting up of the plutonium extraction plant at Marcoule, where the reactor G1 has been operating at power for more than a year, we shall go on next to a another order of magnitude which will allow the manufacture and experimentation of prototype fuel elements. (author) [French] La premiere elaboration de plutonium metallique en France fut faite en janvier 1956, des que nous pumes disposer de quantites de plutonium de l'ordre de quelques grammes, qui avaient ete retires des barreaux de la pile EL2 de Saclay. Ce reacteur, d'une puissance thermique de 2 000 kW, ayant ete jusqu'a present notre seule source de plutonium, nous n'avons encore travaille que sur des quantites experimentales suffisantes pour les essais de base, mais non pour des essais a l'echelle d'applications possibles. Ce sont les travaux effectues pendant cette phase de recherches preliminaires qui seront evoques ci-dessous. Avec la mise eu route de l'usine d'extraction de plutonium de Marcoule, ou le reacteur G1 fonctionne en puissance depuis plus d'un an, nous allons passer prochainement a un autre ordre de grandeur, qui nous permettra la fabrication et l'experimentation d'elements combustibles prototypes. (auteur)

Innovative inert matrix-thoria fuels for in-reactor plutonium disposition

International Nuclear Information System (INIS)

Vettraino, F.; Padovani, E.; Luzzi, L.; Lombardi, C.; Thoresen, H.; Oberlander, B.; Iversen, G.; Espeland, M.

1999-01-01

The present leading option for plutonium disposition, either civilian or weapons Pu, is to burn it in LWRs after having converted it to MOX fuel. However, among the possible types of fuel which can be envisaged to burn plutonium in LWRs, innovative U-free fuels such as inert matrix and thoria fuel are novel concept in view of a more effective and ultimate solution from both security and safety standpoint. Inert matrix fuel is an non-fertile oxide fuel consisting of PuO 2 , either weapon-grade or reactor-grade, diluted in inert oxides such as for ex. stabilized ZrO 2 or MgAl 2 O 4 , its primary advantage consisting in no-production of new plutonium during irradiation, because it does not contain uranium (U-free fuel) whose U-238 isotope is the departure nuclide for breeding Pu-239. Some thoria addition in the matrix (thoria-doped fuel) may be required for coping with reactivity feedback needs. The full thoria-plutonia fuel though still a U-free variant cannot be defined non-fertile any more because the U-233 generation. The advantage of such a fuel option consisting basically on a remarkable already existing technological background and a potential acceleration in getting rid of the Pu stocks. All U-free fuels are envisaged to be operated under a once-through cycle scheme being the spent fuel outlooked to be sent directly to the final disposal in deep geological formations without requiring any further reprocessing treatment, thanks to the quality-poor residual Pu and a very high chemical stability under the current fuel reprocessing techniques. Besides, inert matrix-thoria fuel technology is suitable for in-reactor MAs transmutation. An additional interest in Th containing fuel refers to applicability in ADS, the innovative accelerated driven subcritical systems, specifically aimed at plutonium, minor actnides and long lived fission products transmutation in a Th-fuel cycle scheme which enables to avoid generations of new TRUs. A first common irradiation experiment

Code Analyses Supporting PIE of Weapons-Grade MOX Fuel

International Nuclear Information System (INIS)

Ott, Larry J.; Bevard, Bruce Balkcom; Spellman, Donald J.; McCoy, Kevin

2010-01-01

The U.S. Department of energy has decided to dispose of a portion of the nation's surplus weapons-grade plutonium by reconstituting it into mixed oxide (MOX) fuel and irradiating the fuel in commercial power reactors. Four lead test assemblies (LTAs) were manufactured with weapons-grade mixed oxide (WG-MOX) fuel and irradiated in the Catawba Nuclear Station Unit 1, to a maximum fuel rod burnup of ∼47.3 GWd/MTHM. As part of the fuel qualification process, five rods with varying burnups and initial plutonium contents were selected from one assembly and shipped to the Oak Ridge National Laboratory (ORNL) for hot cell examination. ORNL has provided analytical support for the post-irradiation examination (PIE) of these rods via extensive fuel performance modeling which has aided in instrument settings and PIE data interpretation. The results of these fuel performance simulations are compared in this paper with available PIE data.

Plutonium immobilization project development and testing quality assurance program description - February 1999

International Nuclear Information System (INIS)

MacLean, L. M.; Ziemba, J.

1999-01-01

Lawrence Livermore National Laboratory Immobilization Development and Testing organization (LLNL ID and T) is a Participant in the Plutonium Immobilization Project (PIP). The LLNL D and T has lead responsibilities for form characterization and qualification, ceramic form development, process/equipment development with plutonium, and process systems testing and validation for both conversion and immobilization. This work must be performed in accordance with the graded approach of a Quality Assurance (QA) Program. A QA Program has been developed at LLNL to meet the requirements of the DOE/MD Quality Assurance Requirements. The LLNL QA Program consists of a Quality Assurance Program Description (QAPD) and Quality Implementing Procedures. These documents interface and are a subset of the overall PIP QA Program Documents. The PIP QA Program is described in the PIP ID and T QA Plan, PIP QAPD, and QA Procedures. Other Participant Organizations also must document and describe their PIP compliant QA Programs in a QAPD and implementing procedures. The purpose of this LLNL QAPD is to describe the organization, management processes, QA Controls for Grading, functional responsibilities, levels of authority, and interfaces for those managing, performing, and assessing the adequacy of work

Plutonium speciation and isotope ratios in Yenisey and Ob river and Yenisey estuary

International Nuclear Information System (INIS)

Skipperud, L.; Oughton, DH.; Fifield, K.; Lind, O.C.; Salbu, B.; Brown, J.

2004-01-01

Plutonium isotope ratios are known to vary with reactor type, nuclear fuel-burn up time, neutron flux, and energy, and for fallout from nuclear detonations, weapon type and yield. Weapons-grade plutonium is characterized by a low content of the 240 Pu isotope, with 240 Pu/ 239 Pu isotope ratio less than 0.05. In contrast, both global weapons fallout and spent nuclear fuel from civil reactors have higher 240 Pu/ 239 Pu isotope ratios (civil nuclear power reactors have 240 Pu/ 239 Pu atom ratios of between about 0.2-1). Thus, different sources often exhibit characteristic plutonium isotope ratios and these ratios can be used to identify the origin of contamination, calculate inventories, or follow the migration of contaminated sediments and waters. Together with activity measurements and isotope ratios, knowledge of plutonium speciation in the Ob and Yenisey rivers and processes controlling its behaviour in estuarine systems is a prerequisite for predicting the transfer and subsequent environmental impact to Arctic Seas. With this in mind, the study had two objectives: first to determine whether discharges from nuclear installations in the river catchment areas are having any influence on Pu levels in the estuaries; and, second, to investigate the transfer and mobility of plutonium in the Yenisey river and estuary. Plutonium 240/239 ratios were determined using accelerator mass spectrometry (AMS). The data indicated a clear influence from a low 240 Pu: 239 Pu source in surface sediments collected from the Yenisey Estuary, whereas plutonium in the Ob Estuary sediments are dominated by global fallout. The results also show an increase in plutonium concentration and a decrease in isotope ratio going upstream from the estuary. Sequential extractions of sediments indicate that up 70% of the Pu in the Yenisey river is easily mobilized with weak oxidizing agents, which indicates that the Pu is organically bound, while the Pu is more strongly irreversible bound further out

Cigarette smoke and plutonium

International Nuclear Information System (INIS)

Filipy, R.E.

1985-01-01

Autoradiographic techniques with liquid photographic emulsion and cellulose nitrate track-etch film are being used to investigate the spatial distribution of inhaled plutonium in the lungs of beagle dogs exposed to cigarette smoke or to the plutonium aerosol only. More plutonium than expected was detected on the inner surfaces of bronchi, and particles were observed beneath the bronchial mucosa. 2 figures, 2 tables

Radioactive waste management and plutonium recovery within the context of the development of nuclear energy in Russia

Energy Technology Data Exchange (ETDEWEB)

Kushnikov, V. [V.G. Khlopin Radium Institute, St. Petersburg (Russian Federation)

1996-05-01

The Russian strategy for radioactive waste and plutonium management is based on the concept of the closed fuel cycle that has been adopted in Russia, and, to a great degree, falls under the jurisdiction of the existing Russian nuclear energy structures. From its very beginning, Russian atomic energy policy was based on finding the most effective method of developing the new fuel direction with the maximum possible utilization of the energy potential from the fission of heavy atoms and the achievement of fuel self-sufficiency through the recycling of secondary fuel. Although there can be no doubt about the importance of economic considerations (for the future), concerns for the safety of the environment are currently of the utmost importance. In this context, spent NPP fuel can be viewed as a waste to be buried only if there is persuasive evidence that such an approach is both economically and environmentally sound. The production of I GW of energy per year is accompanied by the accumulation of up to 800-1000 kg of highly radioactive fission products and approximately 250 kg of plutonium. Currently, spent fuel from the VVER 100 and the RBNK reactors contains approximately 25 tons of plutonium. There is an additional 30 tons of fuel-grade plutonium in the form of purified oxide, separated from spent fuels used in VVER440 reactors and other power production facilities, as well as approximately 100 tons of weapons-grade plutonium from dismantled warheads. The spent fuel accumulates significant amounts of small actinoids - neptunium americium, and curium. Science and technology have not yet found technical solutions for safe and secure burial of non-reprocessed spent fuel with such a broad range of products, which are typically highly radioactive and will continue to pose a threat for hundreds of thousands of years.

Sintering uranium oxide in the reaction product of hydrogen-carbon dioxide mixtures

International Nuclear Information System (INIS)

De Hollander, W.R.; Nivas, Y.

1975-01-01

Compacted pellets of uranium oxide alone or containing one or more additives such as plutonium dioxide, gadolinium oxide, titanium dioxide, silica, and alumina are heated to 900 to 1599 0 C in the presence of a mixture of hydrogen and carbon dioxide, either alone or with an inert carrier gas and held at the desired temperature in this atmosphere to sinter the pellets. The sintered pellets are then cooled in an atmosphere having an oxygen partial pressure of 10 -4 to 10 -18 atm of oxygen such as dry hydrogen, wet hydrogen, dry carbon monoxide, wet carbon monoxide, inert gases such as nitrogen, argon, helium, and neon and mixtures of ayny of the foregoing including a mixture of hydrogen and carbon dioxide. The ratio of hydrogen to carbon dioxide in the gas mixture fed to the furnace is controlled to give a ratio of oxygen to uranium atoms in the sintered particles within the range of 1.98:1 to about 2.10:1. The water vapor present in the reaction products in the furnace atmosphere acts as a hydrolysis agent to aid removal of fluoride should such impurity be present in the uranium oxide. (U.S.)

Hazards of plutonium and fuel reprocessing

International Nuclear Information System (INIS)

Watson, G.M.

1978-01-01

Apart from the possibility that civil plutonium may be diverted to military use the main argument against the introduction of a plutonium economy seems to be the supposedly unmanageable biological risk attached to plutonium itself. The author points out weaknesses in many of the opponents' arguments against the increased use of plutonium and argues that current safety practices are more than adequate in handling plutonium and other radioactive materials

A summary of volatile impurity measurements and gas generation studies on MISSTD-1, a high-purity plutonium oxide produced by low-temperature calcination of plutonium oxalate

Energy Technology Data Exchange (ETDEWEB)

Berg, John M. [Los Alamos National Laboratory; Narlesky, Joshua E. [Los Alamos National Laboratory; Veirs, Douglas K. [Los Alamos National Laboratory

2012-06-08

Plutonium dioxide of high specific surface area was subjected to long-term tests of gas generation in sealed containers. The material preparation and the storage conditions were outside the bounds of acceptable parameters defined by DOE-STD-3013-2012 in that the material was stabilized to a lower temperature than required and had higher moisture content than allowed. The data provide useful information for better defining the bounding conditions for safe storage. Net increases in internal pressure and transient increases in H{sub 2} and O{sub 2} were observed, but were well within the bounds of gas compositions previously shown to not threaten integrity of 3013 containers.

A summary of volatile impurity measurements and gas generation studies on MISSTD-1, a high-purity plutonium oxide produced by low-temperature calcination of plutonium oxalate

International Nuclear Information System (INIS)

Berg, John M.; Narlesky, Joshua E.; Veirs, Douglas K.

2012-01-01

Plutonium dioxide of high specific surface area was subjected to long-term tests of gas generation in sealed containers. The material preparation and the storage conditions were outside the bounds of acceptable parameters defined by DOE-STD-3013-2012 in that the material was stabilized to a lower temperature than required and had higher moisture content than allowed. The data provide useful information for better defining the bounding conditions for safe storage. Net increases in internal pressure and transient increases in H 2 and O 2 were observed, but were well within the bounds of gas compositions previously shown to not threaten integrity of 3013 containers.

Plutonium spectrophotometric analysis

International Nuclear Information System (INIS)

Esteban, A.; Cassaniti, P.; Orosco, E.H.

1990-01-01

Plutonium ions in solution have absorption spectra so different that it is possible to use them for analytical purposes. Detailed studies have been performed in nitric solutions. Some very convenient methods for the determination of plutonium and its oxidation states, especially the ratios Pu(III):Pu(IV) and Pu(IV):Pu(VI) in a mixture of both, have been developed. These methods are described in this paper, including: a) Absorption spectra for plutonium (III), (IV), (VI) and mixtures. b) Relative extinction coefficients for the above mentioned species. c) Dependences of the relative extinction coefficients on the nitric acid concentration and the plutonium VI deviation from the Beer-Lambert law. The developed methods are simple and rapid and then, suitable in process control. Accuracy is improved when relative absorbance measurements are performed or controlled the variables which have effect on the spectra and extinction coefficients. (Author) [es

Plutonium safe handling

International Nuclear Information System (INIS)

Tvehlov, Yu.

2000-01-01

The abstract, prepared on the basis of materials of the IAEA new leadership on the plutonium safe handling and its storage (the publication no. 9 in the Safety Reports Series), aimed at presenting internationally acknowledged criteria on the radiation danger evaluation and summarizing the experience in the safe management of great quantities of plutonium, accumulated in the nuclear states, is presented. The data on the weapon-class and civil plutonium, the degree of its danger, the measures for provision of its safety, including the data on accident radiation consequences with the fission number 10 18 , are presented. The recommendations, making it possible to eliminate the super- criticality danger, as well as ignition and explosion, to maintain the tightness of the facility, aimed at excluding the radioactive contamination and the possibility of internal irradiation, to provide for the plutonium security, physical protection and to reduce irradiation are given [ru

Some of the properties of plutonium and the aluminium-plutonium alloy; Quelques proprietes du plutonium et de l'alliage aluminium-plutonium

Energy Technology Data Exchange (ETDEWEB)

Abramson, R; Boucher, R; Fabre, R; Monti, H [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1959-07-01

1- Study of the physical properties of plutonium. 1) Study of the allotropy of plutonium. a) Thermal analysis: the apparatus used and the measurement technique are briefly described. The transition point temperatures and the corresponding heats of transformation have been determined. Finally, the results of the particular study of certain transition points are given. b) Dilatometry. The dilatometric analysis of the phase changes of plutonium has been carried out by means of the Chevenard dilatometer with photographic recording. The testing conditions (heating and cooling speeds, isotherm plateaux) have been varied in order to determine accurately the characteristics of each transition, particularly the {delta} {yields} {gamma} transition on cooling. 2) Micrography of plutonium. For the accurate preparation of metallographic samples the electrolytic polishing must be rapid, which implies a mechanical polishing of excellent quality. Information is given on new attacking reagents which show the structure of the metal very clearly. 2- Study of aluminium-plutonium alloys. Comparative study of Al-Pu and Al-U alloys rich in aluminium. a) Thermal analysis. The liquids and fusion temperatures of the eutectic Al-XAl{sub 4}, have been accurately determined. From the measurement of the heats of fusion the exact composition of the eutectic alloy has been determined. b) Thermal treatments. The eutectic coalescence kinetics have been studied by a micrographic method and by following the evolution of hardness. The results obtained show that the phenomenon is more rapid in Al-Pu alloys than in Al-U alloys. c) Micrographic study of the transition XAl{sub 3} {yields} XAl{sub 4}. The peritectic reaction XAl{sub 3} + liq. {yields} XAl{sub 4} has been suppressed by quenching. The transformation of the XAl{sub 3} phase to the solid phase has been studied as well as the effect of small additions of silicon on the kinetics of this reaction. (author) [French] 1- Etude des proprietes

Material attractiveness of plutonium composition on doping minor actinide of large FBR

International Nuclear Information System (INIS)

Permana, Sidik; Suzuki, Mitsutoshi; Kuno, Yusuke

2011-01-01

Material attractiveness analysis on isotopic plutonium compositions of fast breeder reactors (FBR) has been investigated based on figure of merit (FOM) formulas as key parameters as well as decay heat (DH) and spontaneous fission neutron (SFN) compositions. Increasing minor actinide (MA) doping gives the significant effect to increase Pu-238 composition. However, the compositions of Pu-240 and Pu-242 become less with increasing MA doping. DH and SFN compositions in the core regions similar to the DH and SFN compositions of MOX-grade. Material attractiveness based on FOM1 formula shows all isotopic plutonium compositions in the blanket regions as well as in the core regions are categorized as high attractive material. Adopted FOM2 formula can distinguishes the material attractiveness levels which show the plutonium compositions in blanket regions as high attractiveness level and its composition in the core regions as low level of material attractiveness. MA doping is effective to reduce the material attractiveness level of blanket regions from high to medium and it requires much more MA doping rate to achieve low level of attractiveness (FOM<1) based on adopted FOM1 formula. Low material attractiveness level can be obtained by 4 % or more doping MA based on adopted FOM2 formula which considers not only DH composition effect, but also SFN composition effect that gives relatively higher contribution to material barrier of plutonium isotopes. (author)

Process for recovery of plutonium from fabrication residues of mixed fuels consisting of uranium oxide and plutonium oxide

International Nuclear Information System (INIS)

Heremanns, R.H.; Vandersteene, J.J.

1983-01-01

The invention concerns a process for recovery of plutonium from fabrication residues of mixed fuels consisting of uranium oxide and plutonium oxide in the form of PuO 2 . Mixed fuels consisting of uranium oxide and plutonium oxide are being used more and more. The plants which prepare these mixed fuels have around 5% of the total mass of fuels as fabrication residue, either as waste or scrap. In view of the high cost of plutonium, it has been attempted to recover this plutonium from the fabrication residues by a process having a purchase price lower than the price of plutonium. The problem is essentially to separate the plutonium, the uranium and the impurities. The residues are fluorinated, the UF 6 and PuF 6 obtained are separated by selective absorption of the PuF 6 on NaF at a temperature of at least 400 0 C, the complex obtained by this absorption is dissolved in nitric acid solution, the plutonium is precipitated in the form of plutonium oxalate by adding oxalic acid, and the precipitated plutonium oxalate is calcined

Status of plutonium ceramic immobilization processes and immobilization forms

International Nuclear Information System (INIS)

Ebbinghaus, B.B.; Van Konynenburg, R.A.; Vance, E.R.; Jostsons, A.

1996-01-01

Immobilization in a ceramic followed by permanent emplacement in a repository or borehole is one of the alternatives currently being considered by the Fissile Materials Disposition Program for the ultimate disposal of excess weapons-grade plutonium. To make Pu recovery more difficult, radioactive cesium may also be incorporated into the immobilization form. Valuable data are already available for ceramics form R ampersand D efforts to immobilize high-level and mixed wastes. Ceramics have a high capacity for actinides, cesium, and some neutron absorbers. A unique characteristic of ceramics is the existence of mineral analogues found in nature that have demonstrated actinide immobilization over geologic time periods. The ceramic form currently being considered for plutonium disposition is a synthetic rock (SYNROC) material composed primarily of zirconolite (CaZrTi 2 O 7 ), the desired actinide host phase, with lesser amounts of hollandite (BaAl 2 Ti 6 O 16 ) and rutile (TiO 2 ). Alternative actinide host phases are also being considered. These include pyrochlore (Gd 2 Ti 2 O 7 ), zircon (ZrSiO 4 ), and monazite (CePO 4 ), to name a few of the most promising. R ampersand D activities to address important technical issues are discussed. Primarily these include moderate scale hot press fabrications with plutonium, direct loading of PuO 2 powder, cold press and sinter fabrication methods, and immobilization form formulation issues

Plutonium Plant, Trombay

International Nuclear Information System (INIS)

Yadav, J.S.; Agarwal, K.

2017-01-01

The journey of Indian nuclear fuel reprocessing started with the commissioning of Plutonium Plant (PP) at Trombay on 22"n"d January, 1965 with an aim to reprocess the spent fuel from research reactor CIRUS. The basic process chosen for the plant was Plutonium Uranium Reduction EXtraction (PUREX) process. In seventies, the plant was subjected to major design modifications and replacement of hardware, which later met the additional demand from research reactor DHRUVA. The augmented plutonium plant has been operating since 1983. Experience gained from this plant was very much helpful to design future reprocessing plant in the country

The toxicity of plutonium

International Nuclear Information System (INIS)

Crouse, P.L.

1994-01-01

Shipments of plutonium occasionally pass around the Cape coastal waters on its way to Japan from Europe. This invariably leads to a great deal of speculation of the dangers involved and of the extreme toxicity of plutonium, with the media and environmental groups claiming that (a) plutonium is the most toxic substance known to man, and that (b) a few kilograms of plutonium ground finely and dispersed in the atmosphere could kill every human being on earth. Comparisons with other poisons are drawn, e.g. common inorganic chemicals and biological agents. The original scare around the extraordinary toxicity of Pu seems to have started in 1974 with the claims of Tamplin and Cochran's hot particle theory about plutonium lodging in the sensitive portions of the lungs in small concentrated aggregates where they are much more effective in producing cancers. This theory, however, is regarded as thoroughly discredited by the experts in the field of radiotoxicity. 8 refs

Plutonium use in foreign countries (03)

International Nuclear Information System (INIS)

Otagaki, Takao

2004-03-01

European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experiences of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2003 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which plans to recycle a part of plutonium: Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels: The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories: The data and information of plutonium inventories of foreign countries were collected. (author)

Cigarette smoke and plutonium

International Nuclear Information System (INIS)

Filipy, R.E.

1983-01-01

The major objective of this project is to obtain experimental data that are directly applicable to resolving the question of whether cigarette smokers are at greater risk than nonsmokers to potential health effects of inhaled plutonium. Because cigarette smokers constitute a large fraction of the population, a synergistic effect of plutonium and cigarette smoke might influence estimates of the health risk for plutonium and other transuranics released to the environment

Cycle downstream: the plutonium question

International Nuclear Information System (INIS)

Zask, G.; Rome, M.; Delpech, M.

1998-01-01

This day, organized by the SFEN, took place at Paris the 4 june 1998. Nine papers were presented. They take stock on the plutonium physics and its utilization as a nuclear fuel. This day tried to bring information to answer the following questions: do people have to keep the plutonium in the UOX fuel or in the MOX fuel in order to use it for future fast reactors? Do people have to continue obstinately the plutonium reprocessing in the MOX for the PWR type reactors? Will it be realized a underground disposal? Can it be technically developed plutonium incinerators and is it economically interesting? The plutonium physics, the experimental programs and the possible solutions are presented. (A.L.B.)

Aqueous Solution Chemistry of Plutonium

Energy Technology Data Exchange (ETDEWEB)

Clark, David L. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2014-01-28

Things I have learned working with plutonium: Chemistry of plutonium is complex; Redox equilibria make Pu solution chemistry particularly challenging in the absence of complexing ligands; Understanding this behavior is key to successful Pu chemistry experiments; There is no suitable chemical analog for plutonium.

Gamma ray NDA assay system for total plutonium and isotopics in plutonium product solutions

International Nuclear Information System (INIS)

Cowder, L.R.; Hsue, S.T.; Johnson, S.S.; Parker, J.L.; Russo, P.A.; Sprinkle, J.K.; Asakura, Y.; Fukuda, T.; Kondo, I.

1979-01-01

A LASL-designed gamma-ray NDA instrument for assay of total plutonium and isotopics of product solutions at Tokai-Mura is currently installed and operating. The instrument is, optimally, a densitometer that uses radioisotopic sources for total plutonium measurements at the K absorption edge. The measured transmissions of additional gamma-ray lines from the same radioisotopic sources are used to correct for self-attenuation of passive gamma rays from plutonium. The corrected passive data give the plutonium isotopic content of freshly separated to moderately aged solutions. This off-line instrument is fully automated under computer control, with the exception of sample positioning, and operates routinely in a mode designed for measurement control. A one-half percent precision in total plutonium concentration is achieved with a 15-minute measurement

An autoradiographical method using an imaging plate for the analyses of plutonium contamination in a plutonium handling facility

International Nuclear Information System (INIS)

Takasaki, Koji; Sagawa, Naoki; Kurosawa, Shigeyuki; Mizuniwa, Harumi

2011-01-01

An autoradiographical method using an imaging plate (IP) was developed to analyze plutonium contamination in a plutonium handling facility. The IPs were exposed to ten specimens having a single plutonium particle. Photostimulated luminescence (PSL) images of the specimens were taken using a laser scanning machine. One relatively large spot induced by α-radioactivity from plutonium was observed in each PSL image. The plutonium-induced spots were discriminated by a threshold derived from background and the size of the spot. A good relationship between the PSL intensities of the spots and α-radioactivities measured using a radiation counter was obtained by least-square fitting, taking the fading effect into consideration. This method was applied to workplace monitoring in an actual uranium-plutonium mixed oxide (MOX) fuel fabrication facility. Plutonium contaminations were analyzed in ten other specimens having more than two plutonium spots. The α-radioactivities of plutonium contamination were derived from the PSL images and their relative errors were evaluated from exposure time. (author)

Recovery of plutonium by pyroredox processing

International Nuclear Information System (INIS)

McNeese, J.A.; Bowersox, D.F.; Christensen, D.C.

1985-09-01

Using pyrochemical oxidation and reduction, we have developed a process to recover the plutonium in impure scrap with less than 95% plutonium. This plutonium metal was further purified by pyrochemical electrorefining. During development of the procedures, depleted electrorefining anodes were processed, and over 80% of the plutonium was recovered as high-purity metal in one electrorefining cycle. Over 40 kg of plutonium has been recovered from 55 kg of impure anodes with our procedures. 6 refs., 7 figs., 4 tabs

Recovery of plutonium by pyroredox processing

International Nuclear Information System (INIS)

McNeese, J.A.; Bowersox, D.F.; Christensen, D.C.

1985-01-01

Using pyrochemical oxidation and reduction, we have developed a process to recover the plutonium in impure scrap with less than 95% plutonium. This plutonium metal was further purified by pyrochemical electrorefining. During development of the procedures, depleted electrorefining anodes were processed, and over 80% of the plutonium was recovered as high-purity metal in one electrorefining cycle. Over 40 kg of plutonium has been recovered from 55 kg of impure anodes with our procedures. 6 refs., 2 figs., 5 tabs

The use of calorimetry for plutonium assay

International Nuclear Information System (INIS)

Mason, J.A.

1982-12-01

Calorimetry is a technique for measuring the thermal power of heat-producing substances. The technique may be applied to the measurement of plutonium-bearing materials which evolve heat as a result of alpha and beta decay. A calorimetric measurement of the thermal power of a plutonium sample, combined with a knowledge or measurement of the plutonium isotopic mass ratios of the sample provides a convenient and accurate, non-destructive measure of the total plutonium mass of the sample. The present report provides a description, and an assessment of the calorimetry technique applied to the assay of plutonium-bearing materials. Types and characteristics of plutonium calorimeters are considered, as well as calibration and operating procedures. The instrumentation used with plutonium calorimeters is described and the use of computer control for calorimeter automation is discussed. A critical review and assessment of plutonium calorimetry literature since 1970 is presented. Both fuel element and plutonium-bearing material calorimeters are considered. The different types of plutonium calorimeters are evaluated and their relative merits are discussed. A combined calorimeter and gamma-ray measurement assay system is considered. The design principles of plutonium assay calorimeters are considered. An automatic, computer-based calorimeter control system is proposed in conjunction with a general plutonium assay calorimeter design. (author)

Analytic determination of plutonium in the environment; Determination analytique du plutonium dans l'environnement

Energy Technology Data Exchange (ETDEWEB)

Ballada, J [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-07-01

The work described in this report was undertaken with a view to determining the plutonium content in the fall-out from nuclear explosions. In the first part are described in turn the importance of the problems due to the plutonium, the physico-chemical properties of the radioelement and the biological dangers which it presents. A detailed and critical analysis is made of the radio-toxicological determination of the plutonium as reported in the literature prior to this report. The second part consists in the presentation of a judicious choice of techniques making it possible to determine plutonium in air, rain-water, soils and ash. After a detailed description of the measurement equipment and the operational techniques which have been developed, a justification of these techniques is given with particular reference to their sensitivity and specificity. After a brief conclusion concerning the preceding chapters, the results are presented. These are then discussed in the ease of each element in which the plutonium has been determined. This discussion is concluded by a consideration of the importance of the occurrence of fall-out plutonium on problems relating to public health. From a consideration of 200 analyses carried out, it is concluded that the contribution of plutonium to the exposure of populations is still very small compared to that of natural radiation and that due to such fission products as strontium 90. The report includes 63 literature references, 26 figures and 11 tables. (author) [French] Les travaux decrits dans ce memoire ont ete entrepris et eflectues dans le but de mettre en evidence le plutonium des retombees radioactives consecutives aux explosions nucleaires. Dans la premiere partie nous etudions successivement l'importance des problemes poses par le plutonium puis les proprietes physicochimiques du radioelement et les dangers qu'il presente du point de vue biologique. Nous effectuons une analyse detaillee et critique des techniques

Recovery studies for plutonium machining oil coolant

International Nuclear Information System (INIS)

Navratil, J.D.; Baldwin, C.E.

1977-01-01

Lathe coolant oil, contaminated with plutonium and having a carbon tetrachloride diluent, is generated in plutonium machining areas at Rocky Flats. A research program was initiated to determine the nature of plutonium in this mixture of oil and carbon tetrachloride. Appropriate methods then could be developed to remove the plutonium and to recycle the oil and carbon tetrachloride. Studies showed that the mixtures of spent oil and carbon tetrachloride contained particulate plutonium and plutonium species that are soluble in water or in oil and carbon tetrachloride. The particulate plutonium was removed by filtration; the nonfilterable plutonium was removed by adsorption on various materials. Laboratory-scale tests indicated the lathe-coolant oil mixture could be separated by distilling the carbon tetrachloride to yield recyclable products

Plutonium use in foreign countries (01)

International Nuclear Information System (INIS)

Otagaki, Takao

2002-03-01

European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2001 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which recently appears the move of recycling a part of plutonium. Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels. The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories. The data and information on plutonium inventories of foreign countries were collected. (author)

Plutonium use in foreign countries (99)

International Nuclear Information System (INIS)

Otagaki, Takao

2000-03-01

European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 1999 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which recently appears the move to recycling a part of plutonium backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels. The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories. The data and information on plutonium inventories of foreign counties were collected. (author)

Plutonium use in foreign countries (02)

International Nuclear Information System (INIS)

Otagaki, Takao

2003-02-01

European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2002 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, The U.K., Belgium, Switzerland, and Sweden which recently appears the move of recycling a part of plutonium. Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oside (MOX) fuel fabrication and reprocessing of spent fuels. The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories. The data and information on plutonium inventories of foreign countries were collected. (author)

Plutonium use in foreign countries. (04)

International Nuclear Information System (INIS)

Otagaki, Takao

2005-03-01

European countries and Japan had been implementing the strategy of spent fuel reprocessing in order to use nuclear material to the maximum. Plutonium recovered from reprocessing, however, must be recycle on light water reactors (LWRs) because of considerable delay of fast reactor development. In Europe, much of experience of plutonium recycling have been accumulated until now. Thus, the status of plutonium recycling up to the end of 2004 in France, Germany, The U.K., Belgium, Switzerland and other countries were studied based on the following scope. (1) Basic policy and present status of plutonium recycling in primary countries of France, Germany, the U.K., Belgium, Switzerland, and Sweden which plans to recycle a limited amount of plutonium: Backend policy and the status of spent fuel management were studied, then integrated analysis and evaluation of the position of plutonium recycling in backend and the status of plutonium recycling development were performed. (2) Plan and experience of Mixed Oxide (MOX) fuel fabrication and reprocessing of spent fuels: The data and information on plan and experience of MOX fuel fabrication and reprocessing in foreign countries were collected. (3) Plutonium inventories: The data and information on plutonium inventories of foreign countries were collected. (author)

Laboratory-scale evaluations of alternative plutonium precipitation methods

International Nuclear Information System (INIS)

Martella, L.L.; Saba, M.T.; Campbell, G.K.

1984-01-01

Plutonium(III), (IV), and (VI) carbonate; plutonium(III) fluoride; plutonium(III) and (IV) oxalate; and plutonium(IV) and (VI) hydroxide precipitation methods were evaluated for conversion of plutonium nitrate anion-exchange eluate to a solid, and compared with the current plutonium peroxide precipitation method used at Rocky Flats. Plutonium(III) and (IV) oxalate, plutonium(III) fluoride, and plutonium(IV) hydroxide precipitations were the most effective of the alternative conversion methods tested because of the larger particle-size formation, faster filtration rates, and the low plutonium loss to the filtrate. These were found to be as efficient as, and in some cases more efficient than, the peroxide method. 18 references, 14 figures, 3 tables

The plutonium danger

International Nuclear Information System (INIS)

Ruiter, W. de

1983-01-01

Nobody can ignore the fact that plutonium is potentially very dangerous and the greatest danger concerning it lies in the spreading of nuclear weapons via nuclear energy programmes. The following seven different attitudes towards this problem are presented and discussed: 1) There is no connection between peaceful and military applications; 2) The problem cannot be prevented; 3) A technical solution must be found; 4) plutonium must be totally inaccessible to countries involved in acquiring nuclear weapons; 5) The use of plutonium for energy production should only occur in one multinational centre; 6) Dogmas in the nuclear industry must be enfeebled; 7) All developments in this area should stop. (C.F.)

Method to manufacture a nuclear fuel from uranium-plutonium monocarbide or uranium-plutonium mononitride

International Nuclear Information System (INIS)

Krauth, A.; Mueller, N.

1977-01-01

Pure uranium carbide or nitride is converted with plutonium oxide and carbon (all in powder form) to uranium-plutonium monocarbide or mononitride by cold pressing and sintering at about 1600 0 C. Pure uranium carbide or uranium nitride powder is firstly prepared without extensive safety measures. The pure uranium carbide or nitride powder can also be inactivated by using chemical substances (e.g. stearic acid) and be handled in air. The sinterable uranium carbide or nitride powder (or also granulate) is then introduced into the plutonium line and mixed with a nonstoichiometrically adjusted, prereacted mixture of plutonium oxide and carbon, pressed to pellets and reaction sintered. The surface of the uranium-plutonium carbide (higher metal content) can be nitrated towards the end of the sinter process in a stream of nitrogen. The protective layer stabilizes the carbide against the water and oxygen content in air. (IHOE) [de

Monitoring the risks of plutonium

International Nuclear Information System (INIS)

Holliday, B.

1978-01-01

The difficulties in monitoring the environment in work areas where plutonium is handled are identified and both continuous and personal air sampling techniques considered. Methods of estimating the amounts of plutonium retained in the body are: (1) Direct external counting over the chest of the 'soft' low energy X-rays and gamma rays emitted by the plutonium deposited in the lungs. (2) Measuring plutonium excreted in urine. (3) Analysing faeces soon after a suspected contamination. Limitation of these techniques are discussed and it is shown that estimating the amount of plutonium in the body, or a specific organ, is extremely difficult, both because of the lack of sensitivity of the measuring techniques (especially chest scanning) and because of the problems in interpreting data, stemming from a lack of knowledge of crucial characteristics of the inhaled plutonium (such as particle size and solubility). Nevertheless it is felt that the judicious integration of all the options creates a level of certainty that no individual technique can possibly inspire. (U.K.)

Progress on plutonium stabilization

Energy Technology Data Exchange (ETDEWEB)

Hurt, D. [Defense Nuclear Facilities Safety Board, Washington, DC (United States)

1996-05-01

The Defense Nuclear Facilities Safety Board has safety oversight responsibility for most of the facilities where unstable forms of plutonium are being processed and packaged for interim storage. The Board has issued recommendations on plutonium stabilization and has has a considerable influence on DOE`s stabilization schedules and priorities. The Board has not made any recommendations on long-term plutonium disposition, although it may get more involved in the future if DOE develops plans to use defense nuclear facilities for disposition activities.

Progress on plutonium stabilization

International Nuclear Information System (INIS)

Hurt, D.

1996-01-01

The Defense Nuclear Facilities Safety Board has safety oversight responsibility for most of the facilities where unstable forms of plutonium are being processed and packaged for interim storage. The Board has issued recommendations on plutonium stabilization and has has a considerable influence on DOE's stabilization schedules and priorities. The Board has not made any recommendations on long-term plutonium disposition, although it may get more involved in the future if DOE develops plans to use defense nuclear facilities for disposition activities

Excess Weapons Plutonium Immobilization in Russia

International Nuclear Information System (INIS)

Jardine, L.; Borisov, G.B.

2000-01-01

The joint goal of the Russian work is to establish a full-scale plutonium immobilization facility at a Russian industrial site by 2005. To achieve this requires that the necessary engineering and technical basis be developed in these Russian projects and the needed Russian approvals be obtained to conduct industrial-scale immobilization of plutonium-containing materials at a Russian industrial site by the 2005 date. This meeting and future work will provide the basis for joint decisions. Supporting R and D projects are being carried out at Russian Institutes that directly support the technical needs of Russian industrial sites to immobilize plutonium-containing materials. Special R and D on plutonium materials is also being carried out to support excess weapons disposition in Russia and the US, including nonproliferation studies of plutonium recovery from immobilization forms and accelerated radiation damage studies of the US-specified plutonium ceramic for immobilizing plutonium. This intriguing and extraordinary cooperation on certain aspects of the weapons plutonium problem is now progressing well and much work with plutonium has been completed in the past two years. Because much excellent and unique scientific and engineering technical work has now been completed in Russia in many aspects of plutonium immobilization, this meeting in St. Petersburg was both timely and necessary to summarize, review, and discuss these efforts among those who performed the actual work. The results of this meeting will help the US and Russia jointly define the future direction of the Russian plutonium immobilization program, and make it an even stronger and more integrated Russian program. The two objectives for the meeting were to: (1) Bring together the Russian organizations, experts, and managers performing the work into one place for four days to review and discuss their work with each other; and (2) Publish a meeting summary and a proceedings to compile reports of all the

Plutonium use - Present status and prospects

International Nuclear Information System (INIS)

Dievoet, J. van; Fossoul, E.; Jonckheere, E.; Bemden, E. van den

1977-01-01

The use of plutonium in thermal and fast reactors is a demonstrated, if not proven, technology. Moreover, plutonium is being produced in increasing quantities. Evaluation of this production on a world scale shows that it would be theoretically possible to construct numerous breeders and thus to make the best use of plutonium, while considerably reducing uranium consumption. This source of plutonium is nevertheless dependent on the reprocessing of irradiated fuel. Long delays in installing and adequate world reprocessing capacity are weakening the prospects for introducing breeders. Furthermore, the critical situation regarding reprocessing may delay the development of complementary reprocessing methods for fuels with a high plutonium content and high burnup. The recycling of plutonium is now a well-known technique and any objections to it hardly bear analysis. Utilization of plutonium offers an appreciable saving in terms of uranium and separative work units; and it can also be shown that immediate reprocessing of the recycling fuel is not essential for the economics of the concept. Temporary storage of recycled fuel is a particularly safe form of concentrating plutonium, namely in irradiated plutonium-bearing fuel assemblies. Finally, recycling offers such flexibility that it represents no obstacle to fuel management at power plants with light-water reactors. These strategic considerations imply that the technology of using plutonium for fabricating thermal or fast reactor fuels is both technically reliable and economically viable. The methods used in industrial facilities are fully reassuring in this respect. Although various unsolved problems exist, none seems likely to impede current developments, while the industrial experience gained has enabled the economics and reliability of the methods to be improved appreciably. Apart from the techno-economic aspects, the plutonium industry must face extremely important problems in connection with the safety of personnel

Plutonium recovery from carbonate wash solutions

International Nuclear Information System (INIS)

Gray, J.H.; Reif, D.J.; Chostner, D.F.; Holcomb, H.P.

1991-01-01

540Periodically higher than expected levels of plutonium are found in carbonate solutions used to wash second plutonium cycle solvent. The recent accumulation of plutonium in carbonate wash solutions has led to studies to determine the cause of that plutonium accumulation, to evaluate the quality of all canyon solvents, and to develop additional criteria needed to establish when solvent quality is acceptable. Solvent from three canyon solvent extraction cycles was used to evaluate technology required to measure tributyl phosphate (TBP) degradation products and was used to evaluate solvent quality criteria during the development of plutonium recovery processes. 1 fig

Solubility of plutonium from rumen contents of cattle grazing on plutonium-contaminated desert vegetation in in vitro bovine gastrointestinal fluids

International Nuclear Information System (INIS)

Barth, J.

1975-01-01

Rumen contents of cattle grazing on plutonium-contaminated desert vegetation at the Nevada Test Site were incubated in simulated bovine gastrointestinal fluids to study the alimentary solubility of plutonium. Trials were run during November 1973, and during February, May, July and August 1974. During the May and July trials, a large increase in plutonium solubility accompanied by a marked reduction in plutonium concentration of the rumen contents was observed concurrently with a reduction in intake of Eurotia lanata and an increase in the intake of Oryzopsis hymenoides or Sitanion jubatum. However, during the November, February, and August trials, comparatively high concentration of plutonium, but low plutonium solubility, was associated with high levels of Eurotia lanata in the rumen contents. Plutonium-238 was generally more soluble than plutonium-239 in these fluids. Ratios of the percentage of soluble plutonium-238 to the percentage of soluble plutonium-239 varied fro []1:1 to 18:1 on a radioactivity basis. (auth)

ANL-W MOX fuel lead assemblies data report for the surplus plutonium disposition environmental impact statement

International Nuclear Information System (INIS)

O'Connor, D.G.; Fisher, S.E.; Holdaway, R.

1997-08-01

The purpose of this document is to support the US Department of Energy (DOE) Fissile Materials Disposition Program's preparation of the draft surplus plutonium disposition environmental impact statement (EIS). This is one of several responses to data call requests for background information on activities associated with the operation of the lead assembly (LA) mixed-oxide (MOX) fuel fabrication facility. The DOE Office of fissile Materials Disposition (DOE-MD) has developed a dual-path strategy for disposition of surplus weapons-grade plutonium. One of the paths is to disposition surplus plutonium through irradiation of MOX fuel in commercial nuclear reactors. MOX fuel consists of plutonium and uranium oxides (PuO 2 and UO 2 ), typically containing 95% or more UO 2 . DOE-MD requested that the DOE Site Operations Offices nominate DOE sites that meet established minimum requirements that could produce MOX LAs. The paper describes the following: Site map and the LA facility; process descriptions; resource needs; employment requirements; wastes, emissions, and exposures; accident analysis; transportation; qualitative decontamination and decommissioning; post-irradiation examination; LA fuel bundle fabrication; LA EIS data report assumptions; and LA EIS data report supplement

ANL-W MOX fuel lead assemblies data report for the surplus plutonium disposition environmental impact statement

Energy Technology Data Exchange (ETDEWEB)

O`Connor, D.G.; Fisher, S.E.; Holdaway, R. [and others

1997-08-01

The purpose of this document is to support the US Department of Energy (DOE) Fissile Materials Disposition Program`s preparation of the draft surplus plutonium disposition environmental impact statement (EIS). This is one of several responses to data call requests for background information on activities associated with the operation of the lead assembly (LA) mixed-oxide (MOX) fuel fabrication facility. The DOE Office of fissile Materials Disposition (DOE-MD) has developed a dual-path strategy for disposition of surplus weapons-grade plutonium. One of the paths is to disposition surplus plutonium through irradiation of MOX fuel in commercial nuclear reactors. MOX fuel consists of plutonium and uranium oxides (PuO{sub 2} and UO{sub 2}), typically containing 95% or more UO{sub 2}. DOE-MD requested that the DOE Site Operations Offices nominate DOE sites that meet established minimum requirements that could produce MOX LAs. The paper describes the following: Site map and the LA facility; process descriptions; resource needs; employment requirements; wastes, emissions, and exposures; accident analysis; transportation; qualitative decontamination and decommissioning; post-irradiation examination; LA fuel bundle fabrication; LA EIS data report assumptions; and LA EIS data report supplement.

Plutonium metal burning facility

International Nuclear Information System (INIS)

Hausburg, D.E.; Leebl, R.G.

1977-01-01

A glove-box facility was designed to convert plutonium skull metal or unburned oxide to an oxide acceptable for plutonium recovery and purification. A discussion of the operation, safety aspects, and electrical schematics are included

Analytic determination of plutonium in the environment; Determination analytique du plutonium dans l'environnement

Energy Technology Data Exchange (ETDEWEB)

Ballada, J. [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-07-01

The work described in this report was undertaken with a view to determining the plutonium content in the fall-out from nuclear explosions. In the first part are described in turn the importance of the problems due to the plutonium, the physico-chemical properties of the radioelement and the biological dangers which it presents. A detailed and critical analysis is made of the radio-toxicological determination of the plutonium as reported in the literature prior to this report. The second part consists in the presentation of a judicious choice of techniques making it possible to determine plutonium in air, rain-water, soils and ash. After a detailed description of the measurement equipment and the operational techniques which have been developed, a justification of these techniques is given with particular reference to their sensitivity and specificity. After a brief conclusion concerning the preceding chapters, the results are presented. These are then discussed in the ease of each element in which the plutonium has been determined. This discussion is concluded by a consideration of the importance of the occurrence of fall-out plutonium on problems relating to public health. From a consideration of 200 analyses carried out, it is concluded that the contribution of plutonium to the exposure of populations is still very small compared to that of natural radiation and that due to such fission products as strontium 90. The report includes 63 literature references, 26 figures and 11 tables. (author) [French] Les travaux decrits dans ce memoire ont ete entrepris et eflectues dans le but de mettre en evidence le plutonium des retombees radioactives consecutives aux explosions nucleaires. Dans la premiere partie nous etudions successivement l'importance des problemes poses par le plutonium puis les proprietes physicochimiques du radioelement et les dangers qu'il presente du point de vue biologique. Nous effectuons une analyse detaillee et critique des techniques

Solvent anode for plutonium purification

International Nuclear Information System (INIS)

Bowersox, D.F.; Fife, K.W.; Christensen, D.C.

1986-01-01

The purpose of this study is to develop a technique to allow complete oxidation of plutonium from the anode during plutonium electrorefining. This will eliminate the generation of a ''spent'' anode heel which requires further treatment for recovery. Our approach is to employ a solvent metal in the anode to provide a liquid anode pool throughout electrorefining. We use molten salts and metals in ceramic crucibles at 700 0 C. Our goal is to produce plutonium metal at 99.9% purity with oxidation and transfer of more than 98% of the impure plutonium feed metal from the anode into the salt and product phases. We have met these criteria in experiments on the 100 to 1000 g scale. We plan to scale our operations to 4 kg of feed plutonium and to optimize the process parameters

Design-Only Conceptual Design Report: Plutonium Immobilization Plant

International Nuclear Information System (INIS)

DiSabatino, A.; Loftus, D.

1999-01-01

This design-only conceptual design report was prepared to support a funding request by the Department of Energy Office of Fissile Materials Disposition for engineering and design of the Plutonium Immobilization Plant, which will be used to immobilize up to 50 tonnes of surplus plutonium. The siting for the Plutonium Immobilization Plant will be determined pursuant to the site-specific Surplus Plutonium Disposition Environmental Impact Statement in a Plutonium Deposition Record of Decision in early 1999. This document reflects a new facility using the preferred technology (ceramic immobilization using the can-in-canister approach) and the preferred site (at Savannah River). The Plutonium Immobilization Plant accepts plutonium from pit conversion and from non-pit sources and, through a ceramic immobilization process, converts the plutonium into mineral-like forms that are subsequently encapsulated within a large canister of high-level waste glass. The final immobilized product must make the plutonium as inherently unattractive and inaccessible for use in nuclear weapons as the plutonium in spent fuel from commercial reactors and must be suitable for geologic disposal. Plutonium immobilization at the Savannah River Site uses: (1) A new building, the Plutonium Immobilization Plant, which will convert non-pit surplus plutonium to an oxide form suitable for the immobilization process, immobilize plutonium in a titanate-based ceramic form, place cans of the plutonium-ceramic forms into magazines, and load the magazines into a canister; (2) The existing Defense Waste Processing Facility for the pouring of high-level waste glass into the canisters; and (3) The Actinide Packaging and Storage Facility to receive and store feed materials. The Plutonium Immobilization Plant uses existing Savannah River Site infra-structure for analytical laboratory services, waste handling, fire protection, training, and other support utilities and services. The Plutonium Immobilization Plant

Plutonium isotopic measurements by gamma-ray spectroscopy

International Nuclear Information System (INIS)

Haas, F.X.; Lemming, J.F.

1976-01-01

A nondestructive technique is described for calculating plutonium-238, plutonium-240, plutonium-241 and americium-241 relative to plutonium-239 from measured peak areas in the high resolution gamma-ray spectra of solid plutonium samples. Gamma-ray attenuation effects were minimized by selecting sets of neighboring peaks in the spectrum whose components are due to the different isotopes. Since the detector efficiencies are approximately the same for adjacent peaks, the accuracy of the isotopic ratios is dependent on the half-lives, branching intensities, and measured peak areas. The data presented describe the results obtained by analyzing gamma-ray spectra in the energy region from 120 to 700 keV. Most of the data analyzed were obtained from plutonium material containing 6 percent plutonium-240. Sample weights varied from 0.25 g to approximately 1.2 kg. The methods were also applied to plutonium samples containing up to 23 percent plutonium-240 with weights of 0.25 to 200 g. Results obtained by gamma-ray spectroscopy are compared to chemical analyses of aliquots taken from the bulk samples

Could weapon-grade plutonium be an asset for managing Pu inventories?

International Nuclear Information System (INIS)

Bairiot, H.; Bemden, E. van den

1997-01-01

Due to the temporary shortage of MOX fuel fabrication facilities, the stockpile of separated civilian grade Pu (CPu) is predicted to increase up to the turn of the century. An additional quantity of weapon grade Pu (WPu) will be progressively isolated at the same period. Both CPu and WPu surpluses require disposition as soon as feasible. Although non-proliferation concerns, established national policies, public acceptance problems and other considerations largely complicate the aspect of the use of WPu, it is worth examining the advantages which could result from a synergetic management of: LWR grade Pu to which AGR grade Pu might be associated; WPu; GCR grade Pu which should be considered as a Pu variety situated between the two first ones as far as their physical and neutronic characteristics are concerned. Two scenarios of integrated managements of the CPu varieties and WPu are being considered. They indicate several technical and economical advantages but also important problems to be resolved, mainly from the non-proliferation point of view. In that respect, it is concluded that, although no reasonable perspective exists to resolve these problems easily (or at all), the advantages justify an effort of the international community to consider how it could be implemented. (author). 24 refs, 2 figs, 5 tabs

Bibliography on plutonium and its compounds; Bibliographie sur le plutonium et ses composes

Energy Technology Data Exchange (ETDEWEB)

Dirian, J; Choquet, J [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1958-07-01

Collection of bibliographical references on plutonium and its principal compounds from 1942 to end of 1957. (author) [French] Compilation de references bibliographiques sur le plutonium et ses principaux composes de 1942 a fin 1957. (auteur)

Status of plutonium ceramic immobilization processes and immobilization forms

Energy Technology Data Exchange (ETDEWEB)

Ebbinghaus, B.B.; Van Konynenburg, R.A. [Lawrence Livermore National Lab., CA (United States); Vance, E.R.; Jostsons, A. [Australian Nuclear Science and Technology Organization, Menai (Australia)] [and others

1996-05-01

Immobilization in a ceramic followed by permanent emplacement in a repository or borehole is one of the alternatives currently being considered by the Fissile Materials Disposition Program for the ultimate disposal of excess weapons-grade plutonium. To make Pu recovery more difficult, radioactive cesium may also be incorporated into the immobilization form. Valuable data are already available for ceramics form R&D efforts to immobilize high-level and mixed wastes. Ceramics have a high capacity for actinides, cesium, and some neutron absorbers. A unique characteristic of ceramics is the existence of mineral analogues found in nature that have demonstrated actinide immobilization over geologic time periods. The ceramic form currently being considered for plutonium disposition is a synthetic rock (SYNROC) material composed primarily of zirconolite (CaZrTi{sub 2}O{sub 7}), the desired actinide host phase, with lesser amounts of hollandite (BaAl{sub 2}Ti{sub 6}O{sub 16}) and rutile (TiO{sub 2}). Alternative actinide host phases are also being considered. These include pyrochlore (Gd{sub 2}Ti{sub 2}O{sub 7}), zircon (ZrSiO{sub 4}), and monazite (CePO{sub 4}), to name a few of the most promising. R&D activities to address important technical issues are discussed. Primarily these include moderate scale hot press fabrications with plutonium, direct loading of PuO{sub 2} powder, cold press and sinter fabrication methods, and immobilization form formulation issues.

Plutonium speciation affected by environmental bacteria

International Nuclear Information System (INIS)

Neu, M.P.; Icopini, G.A.; Boukhalfa, H.

2005-01-01

Plutonium has no known biological utility, yet it has the potential to interact with bacterial cellular and extracellular structures that contain metal-binding groups, to interfere with the uptake and utilization of essential elements, and to alter cell metabolism. These interactions can transform plutonium from its most common forms, solid, mineral-adsorbed, or colloidal Pu(IV), to a variety of biogeochemical species that have much different physico-chemical properties. Organic acids that are extruded products of cell metabolism can solubilize plutonium and then enhance its environmental mobility, or in some cases facilitate plutonium transfer into cells. Phosphate- and carboxylate-rich polymers associated with cell walls can bind plutonium to form mobile biocolloids or Pu-laden biofilm/mineral solids. Bacterial membranes, proteins or redox agents can produce strongly reducing electrochemical zones and generate molecular Pu(III/IV) species or oxide particles. Alternatively, they can oxidize plutonium to form soluble Pu(V) or Pu(VI) complexes. This paper reviews research on plutonium-bacteria interactions and closely related studies on the biotransformation of uranium and other metals. (orig.)

Lung, liver and bone cancer mortality after plutonium exposure in beagle dogs and nuclear workers.

Science.gov (United States)

Wilson, Dulaney A; Mohr, Lawrence C; Frey, G Donald; Lackland, Daniel; Hoel, David G

2010-01-01

The Mayak Production Association (MPA) worker registry has shown evidence of plutonium-induced health effects. Workers were potentially exposed to plutonium nitrate [(239)Pu(NO(3))(4)] and plutonium dioxide ((239)PuO(2)). Studies of plutonium-induced health effects in animal models can complement human studies by providing more specific data than is possible in human observational studies. Lung, liver, and bone cancer mortality rate ratios in the MPA worker cohort were compared to those seen in beagle dogs, and models of the excess relative risk of lung, liver, and bone cancer mortality from the MPA worker cohort were applied to data from life-span studies of beagle dogs. The lung cancer mortality rate ratios in beagle dogs are similar to those seen in the MPA worker cohort. At cumulative doses less than 3 Gy, the liver cancer mortality rate ratios in the MPA worker cohort are statistically similar to those in beagle dogs. Bone cancer mortality only occurred in MPA workers with doses over 10 Gy. In dogs given (239)Pu, the adjusted excess relative risk of lung cancer mortality per Gy was 1.32 (95% CI 0.56-3.22). The liver cancer mortality adjusted excess relative risk per Gy was 55.3 (95% CI 23.0-133.1). The adjusted excess relative risk of bone cancer mortality per Gy(2) was 1,482 (95% CI 566.0-5686). Models of lung cancer mortality based on MPA worker data with additional covariates adequately described the beagle dog data, while the liver and bone cancer models were less successful.

Plutonium vulnerability issues at Hanford's Plutonium Finishing Plant

International Nuclear Information System (INIS)

Feldt, E.; Templeton, D.W.; Tholen, E.

1995-01-01

The Plutonium Finishing Plant (PFP) at the Hanford, Washington Site was operated to produce plutonium (Pu) metal and oxide for national defense purposes. Due to the production requirements and methods utilized to meet national needs and the abrupt shutdown of the plant in the late 1980s, the plant was left in a condition that poses a risk of radiation exposure to plant workers, of accidental radioactive material release to the environment, and of radiation exposure to the public. In early 1994, an Environmental Impact Statement (EIS) to determine the best methods for cleaning out and stabilizing Pu materials in the PFP was started. While the EIS is being prepared, a number of immediate actions have been completed or are underway to significantly reduce the greatest hazards in the PFP. Recently, increased attention his been paid to Pu risks at Department of Energy (DOE) facilities resulting in the Department-wide Plutonium Vulnerability Assessment and a recommendation by the Defense Nuclear Facilities Safety Board (DNFSB) for DOE to develop integrated plans for managing its nuclear materials

Physics of Plutonium Recycling in Thermal Reactors

International Nuclear Information System (INIS)

Kinchin, G.H.

1967-01-01

A substantial programme of experimental reactor physics work with plutonium fuels has been carried out in the UK; the purpose of this paper is to review the experimental and theoretical work, with emphasis on plutonium recycling in thermal reactors. Although the main incentive for some of the work may have been to study plutonium build-up in uranium-fuelled reactors, it is nevertheless relevant to plutonium recycling and no distinction is drawn between build-up and enrichment studies. A variety of techniques have been for determining reactivity, neutron spectrum and reaction rates in simple assemblies of plutonium-aluminium fuel with water, graphite and beryllia moderators. These experiments give confidence in the basic data and methods of calculation for near-homogeneous mixtures of plutonium and moderator. In the practical case of plutonium recycling it is necessary to confirm that satisfactory predictions can be made for heterogeneous lattices enriched with plutonium. In this field, experiments have been carried out with plutonium-uranium metal and oxide-cluster fuels in graphite-moderated lattices and in SGHW lattices, and the effects of 240 Pu have been studied by perturbation measurements with single fuel elements. The exponential and critical experiments have used tonne quantities of fuel with plutonium contents ranging from 0.25 to 1.2% and the perturbation experiments have extended both the range of plutonium contents and the range of isotopic compositions of plutonium. In addition to reactivity and reactivity coefficients, such as the temperature coefficients, attention has been concentrated on relative reaction rate distributions which provide evidence for variations of neutron spectrum. .Theoretical comparisons, together with similar comparisons for non-uniform lattices, establish the validity of methods of calculation which have been used to study the feasibility of plutonium recycling in thermal reactors. (author)

Physics of Plutonium Recycling in Thermal Reactors

Energy Technology Data Exchange (ETDEWEB)

Kinchin, G. H. [Atomic Energy Establishment, Winfrith, Dorchester, Dorset (United Kingdom)

1967-09-15

A substantial programme of experimental reactor physics work with plutonium fuels has been carried out in the UK; the purpose of this paper is to review the experimental and theoretical work, with emphasis on plutonium recycling in thermal reactors. Although the main incentive for some of the work may have been to study plutonium build-up in uranium-fuelled reactors, it is nevertheless relevant to plutonium recycling and no distinction is drawn between build-up and enrichment studies. A variety of techniques have been for determining reactivity, neutron spectrum and reaction rates in simple assemblies of plutonium-aluminium fuel with water, graphite and beryllia moderators. These experiments give confidence in the basic data and methods of calculation for near-homogeneous mixtures of plutonium and moderator. In the practical case of plutonium recycling it is necessary to confirm that satisfactory predictions can be made for heterogeneous lattices enriched with plutonium. In this field, experiments have been carried out with plutonium-uranium metal and oxide-cluster fuels in graphite-moderated lattices and in SGHW lattices, and the effects of {sup 240}Pu have been studied by perturbation measurements with single fuel elements. The exponential and critical experiments have used tonne quantities of fuel with plutonium contents ranging from 0.25 to 1.2% and the perturbation experiments have extended both the range of plutonium contents and the range of isotopic compositions of plutonium. In addition to reactivity and reactivity coefficients, such as the temperature coefficients, attention has been concentrated on relative reaction rate distributions which provide evidence for variations of neutron spectrum. .Theoretical comparisons, together with similar comparisons for non-uniform lattices, establish the validity of methods of calculation which have been used to study the feasibility of plutonium recycling in thermal reactors. (author)

Cigarette smoke and plutonium

International Nuclear Information System (INIS)

Filipy, R.E.

1982-01-01

The major objective of this project is to obtain experimental data that are directly applicable to resolving the question of whether cigarette smokers are at greater risk than nonsmokers to potential health effects of inhaled plutonium. Progress was made on two fronts during the past year. The autoradiographic technique developed from detection of plutonium on the interior surface of pulmonary airways (Annual Report, 1978) has been adapted to routine use in examining tracheas and bronchi of rats. Also, dogs exposed to cigarette smoke for over a year after inhalation of plutonium were killed and necropsied

Plutonium inventories for stabilization and stabilized materials

Energy Technology Data Exchange (ETDEWEB)

Williams, A.K.

1996-05-01

The objective of the breakout session was to identify characteristics of materials containing plutonium, the need to stabilize these materials for storage, and plans to accomplish the stabilization activities. All current stabilization activities are driven by the Defense Nuclear Facilities Safety Board Recommendation 94-1 (May 26, 1994) and by the recently completed Plutonium ES&H Vulnerability Assessment (DOE-EH-0415). The Implementation Plan for accomplishing stabilization of plutonium-bearing residues in response to the Recommendation and the Assessment was published by DOE on February 28, 1995. This Implementation Plan (IP) commits to stabilizing problem materials within 3 years, and stabilizing all other materials within 8 years. The IP identifies approximately 20 metric tons of plutonium requiring stabilization and/or repackaging. A further breakdown shows this material to consist of 8.5 metric tons of plutonium metal and alloys, 5.5 metric tons of plutonium as oxide, and 6 metric tons of plutonium as residues. Stabilization of the metal and oxide categories containing greater than 50 weight percent plutonium is covered by DOE Standard {open_quotes}Criteria for Safe Storage of Plutonium Metals and Oxides{close_quotes} December, 1994 (DOE-STD-3013-94). This standard establishes criteria for safe storage of stabilized plutonium metals and oxides for up to 50 years. Each of the DOE sites and contractors with large plutonium inventories has either started or is preparing to start stabilization activities to meet these criteria.

Interference from radon-thoron daughters in plutonium channel of a continuous plutonium-in-air monitor

International Nuclear Information System (INIS)

Pendharkar, K.A.; Krishnamony, S.

1983-01-01

This paper summarises the results of a study conducted to define the extent of interference from the daughter products of radon/thoron to the plutonium channel of a continuous plutonium-in-air monitor. The effect on the detection limits of the instrument due to chemical form (transportable or non-transportable) and isotopic composition of plutonium aerosol are briefly discussed. (author)

Compositions of airborne plutonium-bearing particles from a plutonium finishing operation

International Nuclear Information System (INIS)

Sanders, S.M. Jr.

1976-11-01

The elemental composition of 111 plutonium-bearing particles was determined (using an electron microprobe) as part of a program to investigate the origin and behavior of the long-lived transuranic radionuclides released from fuel reprocessing facilities at the Savannah River Plant. These particles, collected from wet-cabinet and room-air exhausts from the plutonium finishing operation (JB-Line), were between 0.4 and 36 μm in diameter. Ninety-nine of the particles were found to be aggregates of various minerals and metals, six were quartz, and six were small (less than 2-μm-diameter) pieces of iron oxide. Collectively, these particles contained less minerals and more metals than natural dusts contain. The metallic constituents included elements normally not found in dusts, e.g., chromium, nickel, copper, and zinc. Concentrations of aluminum and iron exceeded those normally found in minerals. Elemental concentrations in individual particles covered a wide range: one 2-μm-diameter particle contained 97 percent NiO, a 9-μm-diameter particle contained 72 percent Cr 2 O 3 . Although the particles were selected because they produced plutonium fission tracks, the plutonium concentration was too low to be estimated by microprobe analysis in all but a 1-μm-diameter particle. This plutonium-bearing particle contained 73 percent PuO 2 by weight in combination with Fe 2 O 3 and mica; its activity was estimated at 0.17 pCi of 239 Pu

Plutonium use - present status and perspectives

International Nuclear Information System (INIS)

Dievoet, J. van; Fossoul, E.; Jonckheere, E.; Bemden, E. van den

1977-01-01

Plutonium is being produced in increasing quantities in the so-called proven reactors, which are mostly of the light-water type. Evaluation of this production on a world scale shows that it would be theoretically possible to construct a large number of breeders and thus to make the best use of the intrinsic qualities of plutonium as a fissionable material, while considerably reducing the consumption of uranium. This source of plutonium is nevertheless dependent on an essential stage of the fuel cycle, namely reprocessing of irradiated fuel. The long delays in installing an adequate world reprocessing capacity are substantially weakening the prospects for the introduction of breeders. Furthermore, the critical situation as regards reprocessing may delay the development of complementary reprocessing methods for fuels with a high plutonium content and high burn-up. When it is recalled that fast reactors themselves may suffer some delay in their technological development, if only because of the intention to build power plants of very high unit capacity immediately, it must be concluded that another use will have to be considered for the plutonium available in future -use in thermal reactors, i.e. recycling. The recycling of plutonium is a well-known technique today and the objections which could be raised against it hardly stand up to analysis. Utilization of plutonium offers an appreciable saving in terms of uranium and separative work units, the consumption being of a low order of magnitude in comparison with the total amount of plutonium needed for the eventual fabrication of the first fast reactor cores. It can also be shown that immediate reprocessing of the recycling fuel is not essential for the economics of the concept. Temporary storage of recycled fuel has the advantage of concentrating plutonium in a particularly safe form, namely in irradiated plutonium-bearing fuel assemblies. Lastly, recycling offers such flexibility that it does not in practice represent

Alternative technical summary report for direct disposition in deep boreholes: Direct disposal of plutonium metal/plutonium dioxide in compound canisters, Version 4.0. Fissile Materials Disposition Program

Energy Technology Data Exchange (ETDEWEB)

Wijesinghe, A.M.

1996-08-23

This report summarizes and compares the Immobilized and Direct Beep Borehole Disposition Alternatives. The important design concepts, facility features and operational procedures are briefly described, and a discussion of the issues that affect the evaluation of each alternative against the programmatic assessment criteria that have been established for selecting the preferred alternatives for plutonium disposition.

Plutonium biokinetics in humans

International Nuclear Information System (INIS)

Popplewell, D.; Ham, G.; McCarthy, W.; Lands, C.

1994-01-01

By using an 'unusual' isotope it is possible to carry out experiments with plutonium in volunteers at minimal radiation dose levels. Measurements have been made of the gut transfer factor and the urinary excretion of plutonium after intravenous injection. (author)

Cigarette smoke and plutonium

International Nuclear Information System (INIS)

Anon.

1981-01-01

The overall objective of this study is to determine whether cigarette smoking increases the probability of plutonium-induced lung cancer. Initial experiments, designed to characterize the effect of chronic cigarette smoke exposure on pulmonary clearance of plutonium aerosols, are described

Effects of human food grade titanium dioxide nanoparticle dietary exposure on Drosophila melanogaster survival, fecundity, pupation and expression of antioxidant genes.

Science.gov (United States)

Jovanović, Boris; Cvetković, Vladimir J; Mitrović, Tatjana Lj

2016-02-01

The fruitfly, Drosophila melanogaster was exposed to the human food grade of E171 titanium dioxide (TiO2). This is a special grade of TiO2 which is frequently omitted in nanotoxicology studies dealing with TiO2, yet it is the most relevant grade regarding oral exposure of humans. D. melanogaster larvae were exposed to 0.002 mg mL(-1), 0.02 mg mL(-1), 0.2 mg mL(-1), and 2 mg mL(-1) of TiO2 in feeding medium, and the survival, fecundity, pupation time, and expression of genes involved in oxidative stress response were monitored. TiO2 did not affect survival but significantly increased time to pupation (p TiO2 was present in a significant amount in larvae, but was not transferred to adults during metamorphosis. Two individuals with aberrant phenotype similar to previously described gold nanoparticles induced mutant phenotypes were detected in the group exposed to TiO2. In general, TiO2 showed little toxicity toward D. melanogaster at concentrations relevant to oral exposure of humans. Copyright © 2015 Elsevier Ltd. All rights reserved.

Polarographic study of the electrochemical properties of plutonium; Etude polarographique des proprietes electrochimiques du plutonium

Energy Technology Data Exchange (ETDEWEB)

Guichard, C [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1968-07-01

The behaviour of the different degrees of oxidation of plutonium have been studied using a falling drop mercury electrode in a non-complexing medium: dilute perchloric acid. In this medium it is possible to carry out the polarographic determination of plutonium using the reduction step situated at - 0.54 V/ECS which corresponds to the passage from the degree of oxidation(V) to the degree(III). The modifications brought about by a complexing ion, acetate, are then observed and interpreted. The existence of two plutonium(IV) acetic complexes has been shown; one is a polymerized substance. (author) [French] Le comportement des differents degres d'oxydation du plutonium est etudie a l'electrode a gouttes de mercure dans un milieu non complexant: l'acide perchlorique dilue. Il est possible dans ce milieu d'effectuer le dosage polarographique du plutonium en utilisant la vague de reduction situee a - 0.54 V/ECS qui correspond au passage du degre d'oxydation(V) au degre(III). Les modifications apportees par un ion complexant, l'acetate, sont ensuite observees et interpretees. Deux complexes acetiques du plutonium(IV) ont ete mis en evidence, dont l'un est un compose polymerise. (auteur)

Standard specification for sintered gadolinium oxide-uranium dioxide pellets

CERN Document Server

American Society for Testing and Materials. Philadelphia

2008-01-01

1.1 This specification is for finished sintered gadolinium oxide-uranium dioxide pellets for use in light-water reactors. It applies to gadolinium oxide-uranium dioxide pellets containing uranium of any 235U concentration and any concentration of gadolinium oxide. 1.2 This specification recognizes the presence of reprocessed uranium in the fuel cycle and consequently defines isotopic limits for gadolinium oxide-uranium dioxide pellets made from commercial grade UO2. Such commercial grade UO2 is defined so that, regarding fuel design and manufacture, the product is essentially equivalent to that made from unirradiated uranium. UO2 falling outside these limits cannot necessarily be regarded as equivalent and may thus need special provisions at the fuel fabrication plant or in the fuel design. 1.3 This specification does not include (1) provisions for preventing criticality accidents or (2) requirements for health and safety. Observance of this specification does not relieve the user of the obligation to be aw...

Screening study for evaluation of the potential for system 80+ to consume excess plutonium - Volume 1

International Nuclear Information System (INIS)

1994-01-01

As part of the U.S. effort to evaluate technologies offering solutions for the safe disposal or utilization of surplus nuclear materials, the fiscal year 1993 Energy and Water Appropriations legislation provided the Department of Energy (DOE) the necessary funds to conduct multi-phased studies to determine the technical feasibility of using reactor technologies for the triple mission of burning weapons grade plutonium, producing tritium for the existing smaller weapons stockpile, and generating commercial electricity. DOE limited the studies to five advanced reactor designs. Among the technologies selected is the ABB-Combustion Engineering (ABB-CE) System 80+. The DOE study, currently in Phase ID, is proceeding with a more detailed evaluation of the design's capability for plutonium disposition

Screening study for evaluation of the potential for system 80+ to consume excess plutonium - Volume 2

International Nuclear Information System (INIS)

1994-01-01

As part of the U.S. effort to evaluate technologies offering solutions for the safe disposal or utilization of surplus nuclear materials, the fiscal year 1993 Energy and Water Appropriations legislation provided the Department of Energy (DOE) the necessary funds to conduct multi-phased studies to determine the technical feasibility of using reactor technologies for the triple mission of burning weapons grade plutonium, producing tritium for the existing smaller weapons stockpile, and generating commercial electricity. DOE limited the studies to five advanced reactor designs. Among the technologies selected is the ABB-Combustion Engineering (ABB-CE) System 80+. The DOE study, currently in Phase ID, is proceeding with a more detailed evaluation of the design's capability for plutonium disposition

Plutonium working group report on environmental, safety and health vulnerabilities associated with the Department's plutonium storage. Volume I: Summary

International Nuclear Information System (INIS)

1994-11-01

At the conclusion of the Cold War, the Department of Energy (DOE) stopped plutonium processing for nuclear weapons production. Facilities used for that purpose now hold significant quantities of plutonium in various forms. Unless properly stored and handled, plutonium can present environment, safety and health (ES ampersand H) hazards. Improperly stored plutonium poses a variety of hazards. When containers or packaging fail to fully protect plutonium metal from exposure to air, oxidation can occur and cause packaging failures and personnel contamination. Contamination can also result when plutonium solutions leak from bottles, tanks or piping. Plutonium in the form of scrap or residues generated by weapons production are often very corrosive, chemically reactive and difficult to contain. Buildings and equipment that are aging, poorly maintained or of obsolete design contribute to the overall problem. Inadvertent accumulations of plutonium of any form in sufficient quantities within facilities can result in nuclear criticality events that could emit large amounts of radiation locally. Contamination events and precursors of criticality events are causing safety and health concerns for workers at the Department's plutonium facilities. Contamination events also potentially threaten the public and the surrounding environment

Search for plutonium salt deposits in the plutonium extraction batteries of the Marcoule plant (1963); Recherche de depots de sels de plutonium dans les batteries d'extraction du plutonium de l'usine de Marcoule (1963)

Energy Technology Data Exchange (ETDEWEB)

Bouzigues, H; Reneaud, J M [Commissariat a l' Energie Atomique, Centre de Production de Plutonium, Marcoule (France). Centre d' Etudes Nucleaires

1963-07-01

This report describes a method and a special apparatus making it possible to detach the insoluble plutonium salt deposits in the extraction chain of an irradiated fuel treatment plant. The process chosen allows the detection, in the extraction batteries or in the highly active chemical engineering equipment, of plutonium quantities of a few grains. After four years operation it has been impossible to detect measurable quantities of plutonium in any part of the extraction chain. The results have been confirmed by visual examinations carried out with a specially constructed endoscope. (authors) [French] Ce rapport decrit une methode et un montage special permettant de detacher les accumulations de sels de plutonium insolubles dans les chaines d'extraction d'une usine de traitement de combustible irradie. Le procede retenu permet de reperer, dans des batteries d'extraction ou dans l'appareillage de genie chimique fortement actif, des masses de plutonium de quelques grammes. Apres quatre annees de fonctionnement, il n'a pas ete possible de deceler des quantites ponderables de plutonium en aucun endroit de la chaine d'extraction. Ces resultats ont ete confirmes par les examens visuels effectues a l'aide d'un endoscope concu specialement pour cet usage. (auteurs)

A World made of Plutonium?

International Nuclear Information System (INIS)

Broda, E.

1976-01-01

This lecture by Engelbert Broda was written for the 26th Pugwash Conference in Mühlhausen, Germany, 26 – 31 August 1976: Public doubts about nuclear energy are generally directed at the problems of routine emissions of radionuclides, of catastrophic accidents, and of terminal waste disposal. Curiously, the most important problem is not being given sufficient attention: The use of plutonium from civilian reactors fpr weapons production. According to current ideas about a nuclear future, 5000 tons (order of magnitude) of plutonium are to be made annually by year 2000, and about 10 000 tons will all the time be in circulation (transport, reprocessing, reproduction of fuel elements, etc.). It is a misconception that plutonium from power reactors is unsuitable as a nuclear explosive. 5000 tons are enough for several hundred thousand (!) of bombs, Nagasaki type. By the year 2000 maybe 40 – 50 countries will have home-made plutonium. Plutonium production and proliferation are the most serious problems in a nuclear world. (author)

Using Biomolecules to Separate Plutonium

Science.gov (United States)

Gogolski, Jarrod

Used nuclear fuel has traditionally been treated through chemical separations of the radionuclides for recycle or disposal. This research considers a biological approach to such separations based on a series of complex and interdependent interactions that occur naturally in the human body with plutonium. These biological interactions are mediated by the proteins serum transferrin and the transferrin receptor. Transferrin to plutonium in vivo and can deposit plutonium into cells after interacting with the transferrin receptor protein at the cell surface. Using cerium as a non-radioactive surrogate for plutonium, it was found that cerium(IV) required multiple synergistic anions to bind in the N-lobe of the bilobal transferrin protein, creating a conformation of the cerium-loaded protein that would be unable to interact with the transferrin receptor protein to achieve a separation. The behavior of cerium binding to transferrin has contributed to understanding how plutonium(IV)-transferrin interacts in vivo and in biological separations.

Disposition of plutonium-239 via production of fission molybdenum-99

Energy Technology Data Exchange (ETDEWEB)

Mushtaq, A., E-mail: muahtaq_a1953@hotmail.co [Isotope Production Division, Pakistan Institute of Nuclear Science and Technology, P.O. Nilore, Islamabad (Pakistan)

2011-04-15

A heritage of physical consequences of the U.S.-Soviet arms race has accumulated, the weapons-grade plutonium (WPu), which will become excess as a result of the dismantlement of the nuclear weapons under the arms reduction agreements. Disposition of Pu has been proposed by mixing WPu with high-level radioactive waste with subsequent vitrification into large, highly radioactive glass logs or fabrication into mixed oxide fuel with subsequent irradiation in existing light water reactors. A potential option may be the production of medical isotope molybdenum-99 by using Pu-239 targets.

MOX fuel: a contribution to disarmament. U.S. utilities' response to DOE's plutonium disposition decision

International Nuclear Information System (INIS)

Wallace, M.

1997-01-01

The author is chairman of the Nuclear Energy Institute Plutonium Disposition Working Group, which includes 11 nuclear utilities, including Ontario Hydro, and all the European fabricators of mixed oxide (MOX) fuel. A feasibility study is going on, to see if Russian or other weapons grade plutonium made into MOX fuel can be used in US, Canadian, or other power reactors. The US nuclear power industry is going through a period of change, and its primary responsibility must be the safe, reliable and economic operation of its plants. There is no current US MOX capacity, but the Europeans have have manufactured and burned over 400 tons of MOX fuel since 1963. Canada may be involved, initially through a pilot-scale experiment in NRU reactor

Safe handling of kilogram amounts of fuel-grade plutonium and of gram amounts of plutonium-238, americium-241 and curium-244

International Nuclear Information System (INIS)

Louwrier, K.P.; Richter, K.

1976-01-01

During the past 10 years about 600 glove-boxes have been installed at the Institute for Transuranium Elements at Karlsruhe. About 80% of these glove-boxes have been designed and equipped for handling 100-g to 1-kg amounts of 239 Pu containing 8-12% 240 Pu (low-exposure plutonium). A small proportion of the glove-boxes is equipped with additional shielding in the form of lead sheet or lead glass for work with recycled plutonium. In these glove-boxes gram-amounts of 241 Am have also been handled for preparation of Al-Am targets using tongs and additional shielding inside the glove-boxes themselves. Water- and lead-shielded glove-boxes equipped with telemanipulators have been installed for routine work with gram-amounts of 241 Am, 243 Am and 244 Cm. A prediction of the expected radiation dose for the personnel is difficult and only valid for a preparation procedure with well-defined preparation steps, owing to the fact that gamma dose-rates depend strongly upon proximity and source seize. Gamma radiation dose measurements during non-routine work for 241 Am target preparation showed that handling of gram amounts leads to a rather high irradiation dose for the personnel, despite lead or steel glove-box shielding and shielding within the glove-boxes. A direct glove-hand to americium contact must be avoided. For all glove-handling of materials with gamma radiation an irradiation control of the forearms of the personnel by, for example, thermoluminescence dosimeters is necessary. Routine handling of americium and curium should be executed with master-slave equipment behind neutron and gamma shielding. (author)

Oxygen partial pressure control during in-situ high temperature X-ray diffraction on cerium dioxide

International Nuclear Information System (INIS)

Strach, M.; Belin, R.C.; Richaud, J-C.; Rogez, J.

2014-01-01

Cerium dioxide is widely used as a surrogate for plutonium dioxide in the studies of MOX type nuclear fuel. Thus, obtaining an accurate description of the structures present in this system in a range of temperatures is of importance to the development of fuel for the IV. generation of nuclear reactors. However, such a study requires appropriate scientific tools, in particular regarding the control and monitoring of the oxygen partial pressure (pO 2 ). Here we discuss several in-situ X-ray diffraction experiments performed to determine the phases present in the hypo-stoichiometric CeO 2-x region of the phase diagram and clearly demonstrate the need for controlling the pO 2 . (authors)

Continuous precipitation process of plutonium salts; Procede continu de precipitation des sels de plutonium

Energy Technology Data Exchange (ETDEWEB)

Richard, P [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1967-03-01

This work concerns the continuous precipitation process of plutonium oxalate. Investigations about the solubility of different valence states in nitric-oxalic and in nitric-sulfuric-oxalic medium lead to select the precipitation process of tetravalent plutonium oxalate. Settling velocity and granulometry of tetravalent oxalate plutonium have been studied with variation of several precipitation parameters such as: temperature, acidity, excess of oxalic acid and aging time. Then are given test results of some laboratory continuous apparatus. Conditions of operation with adopted tubular apparatus are defined in conclusion. A flow-sheet is given for a process at industrial scale. (author) [French] Cette etude porte sur la precipitation continue de l'oxalate de plutonium. L'etude de la solubilite des differentes valences du plutonium dans des milieux acides nitrique-oxalique, puis nitrique-sulfurique-oxalique conduit a choisir la precipitation de l'oxalate de plutonium tetravalent. L'etude porte ensuite sur la sedimentation et la granulometrie de l'oxalate de Pu{sup 4+} obtenue en faisant varier differents parametres de la precipitation : la temperature, l'acidite, l'exces oxalique et le temps de murissement. La derniere partie traite des resultats obtenus avec plusieurs types d'appareils continus essayes au laboratoire. En conclusion sont donnees les conditions de marche de l'appareil tubulaire adopte, ainsi qu'une extrapolation a l'echelle industrielle sous forme d'un flow-sheet. (auteur)

Plutonium dispositioning in CANDU

International Nuclear Information System (INIS)

Boczar, P.G.; Feinroth, H.; Luxat, J.C.

1995-07-01

Recently, the U.S. Department of Energy (DOE) sponsored Atomic Energy of Canada Limited (AECL) to evaluate salient technical, strategic, schedule, and cost-related parameters of using CANDU reactors for dispositioning of weapons-grade plutonium in the form of Mixed OXide (MOX) fuel. A study team, consisting of key staff from the CANDU reactor designers and researchers (AECL), operators (Ontario Hydro) and fuel suppliers, analyzed all significant factors involved in such application, with the objective of identifying an arrangement that would permit the burning of MOX in CANDU at the earliest date. One of Ontario Hydro's multi-unit stations, Bruce A nuclear generating station (4x769 MW(e)), was chosen as the reference for the study. The assessment showed that no significant modifications of reactor or process systems are necessary to operate with a full MOX core. Plant modifications would be limited to fuel handling and modifications necessary to accommodate enhanced security and safeguards requirements. No safety limitations were identified

Plutonium helps probe protein, superconductor

International Nuclear Information System (INIS)

Anon.

1990-01-01

Scientists are finding that plutonium can be a useful research tool that may help them answer important questions in fields as diverse as biochemistry and solid-state physics. This paper reports that U.S. research involving plutonium is confined to the Department of Energy's national laboratories and centers around nuclear weapons technology, waste cleanup and disposal, and health effects. But at Los Alamos National Laboratory, scientists also are using plutonium to probe the biochemical behavior of calmodulin, a key calcium-binding protein that mediates calcium-regulated processes in biological systems. At Argonne National Laboratory, another team is trying to learn how a superconductor's properties are affected by the 5f electrons of an actinide like plutonium

Technological alternatives for plutonium transport

International Nuclear Information System (INIS)

1978-12-01

This paper considers alternative transport modes (air, sea, road, rail) for moving (1) plutonium from a reprocessing plant to a store or a fuel fabrication facility, and (2) MOX fuel from the latter to a reactor. These transport modes and differing forms of plutonium are considered in terms of: their proliferation resistance and safeguards; environmental and safety aspects; and economic aspects. It is tentatively proposed that the transport of plutonium could continue by air or sea where long distances are involved and by road or rail over shorter distances; this would be acceptable from the non-proliferation, environmental impact and economic aspects - there may be advantages in protection if plutonium is transported in the form of mixed oxide

Gamma spectrometric methods for measuring plutonium

International Nuclear Information System (INIS)

Gunnink, R.

1978-01-01

Nondestructive analyses of plutonium can be made by detecting and measuring the gamma rays emitted by a sample. Although qualitative and semiquantitative assays can be performed with relative ease, only recently have methods been developed, using computer analysis techniques, that provide quantitative results. This paper reviews some new techniques developed for measuring plutonium. The features of plutonium gamma-ray spectra are reviewed and some of the computer methods used for spectrum analysis are discussed. The discussion includes a description of a powerful computer method of unfolding complex peak multiplets that uses the standard linear least-squares techniques of data analysis. This computer method is based on the generation of response profiles for the isotopes composing a plutonium sample and requires a description of the peak positions, relative intensities, and line shapes. The principles that plutonium isotopic measurements are based on are also developed, followed by illustrations of the measurement procedures as applied to the quantitative analysis of plutonium liquid and solid samples

Plutonium

Energy Technology Data Exchange (ETDEWEB)

Miner, William N

1964-01-01

This pamphlet discusses plutonium from discovery to its production, separation, properties, fabrication, handling, and uses, including use as a reactor fuel and use in isotope power generators and neutron sources.

Plutonium Vulnerability Management Plan

International Nuclear Information System (INIS)

1995-03-01

This Plutonium Vulnerability Management Plan describes the Department of Energy's response to the vulnerabilities identified in the Plutonium Working Group Report which are a result of the cessation of nuclear weapons production. The responses contained in this document are only part of an overall, coordinated approach designed to enable the Department to accelerate conversion of all nuclear materials, including plutonium, to forms suitable for safe, interim storage. The overall actions being taken are discussed in detail in the Department's Implementation Plan in response to the Defense Nuclear Facilities Safety Board (DNFSB) Recommendation 94-1. This is included as Attachment B

Preparation of plutonium hexafluoride. Recovery of plutonium from waste dross (1962); Preparation de l'hexafluorure de plutonium. Recuperation du plutonium des scories d'elaboration (1962)

Energy Technology Data Exchange (ETDEWEB)

Gendre, R [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1962-07-01

The object of this work is to study the influence of various physical factors on the rate of fluorination of solid plutonium tetrafluoride by fluorine. In a horizontal oven with a circulation for pure fluorine at atmospheric pressure and 520 deg. C, at a fluorine rate of 9 litres/hour, it is possible to transform 3 g of tetrafluoride to hexafluoride with about 100 per cent transformation and a recovery yield of over 90 per cent, in 4 to 5 hours. The fluorination rate is a function of the temperature, of the fluorine flow-rate, of the crucible surface, of the depth of the tetrafluoride layer and of the reaction time. It does not depend on the diffusion of the fluorine into the solid but is determined by the reaction at the gas-solid interface and obeys the kinetic law (1 - T{sub T}){sup 1/3} = kt + 1. The existence of intermediate fluorides, in particular Pu{sub 4} F{sub 17}, is confirmed by a break in the Arrhenius plot at about 370 deg. C, by differences in the fluorination rates inside the tetrafluoride layer, and by reversible colour changes. The transformation to hexafluoride occurs with a purification with respect of the foreign elements present in the initial plutonium. Recovery of plutonium from waste dross: The study is based on the transformation of occluded plutonium particles to gaseous hexafluoride which is then decomposed thermally to the tetrafluoride which can be reintroduced directly in the production circuit. Under the conditions considered this process is not applicable industrially. After milling, it is possible to separate the dross into enriched (75 per cent Pu in 2.6 per cent by weight of dross) and depleted portions. By prolonged fluorination (16 hours) of the various fractions it is possible to recover about 80 per cent of the plutonium. A treatment plant using fluidization, as described at the end of this study, should make it possible to substantially improve the yield. (author) [French] L'objet de l'etude est l'influence des differents

Modeling of Diffusion of Plutonium in Other Metals and of Gaseous Species in Plutonium-Based Systems

International Nuclear Information System (INIS)

Cooper, Bernard R.; Gayanath W. Fernando; Beiden, S.; Setty, A.; Sevilla, E.H.

2004-01-01

Establish standards for temperature conditions under which plutonium, uranium, or neptunium from nuclear wastes permeates steel, with which it is in contact, by diffusion processes. The primary focus is on plutonium because of the greater difficulties created by the peculiarities of face-centered-cubic-stabilized (delta) plutonium (the form used in the technology generating the waste)

Prospects for the Use of Plutonium in Reactors; Prospective d'Utilisation du Plutonium dans les Reacteurs

Energy Technology Data Exchange (ETDEWEB)

Fossoul, E.; Haubert, P. [BELGONUCLEAIRE (Belgium); Hirschberg, D.; Morlet, E. [International Business Machines of Belgium, Bruxelles (Belgium)

1967-09-15

The introduction, at an increasing rate, of power reactors using slightly enriched uranium will inevitably lead to the production of considerable quantities of plutonium over the next decade. Fast reactors will not be capable of absorbing this material before 1980. The question thus arises of whether one should store the plutonium far future use in fast reactors, recycle it in existing thermal reactors, or try to sell it. The problem has been studied for an electric power generating system that does not foresee selling the plutonium produced by its reactors and does not buy plutonium outside, which enables a good approximation to be made and eliminates the major unknown quantity represented by the future market price of plutonium. Assuming within this system a programme that provides for the construction of power reactors of a given type and capacity at specific dates, the utilization of the plutonium produced can be optimized by linear programming techniques so as to minimize the discounted total cost of the power generated over a given period. A later stage consists in optimizing, by various techniques, not only the utilization but also the production of plutonium by appropriate selection of the power reactor types to be constructed. (author) [French] L'implantation, a un rythme croissant, de centrales nucleaires a uranium legerement enrichi entrainera la production ineluctable d'une quantite importante de plutonium au cours de la prochaine decennie. Les reacteurs a neutrons rapides ne seront capables d'absorber cette production qu'apres 1980. La question se pose donc de savoir s'il est preferable de stocker le plutonium en vue de son utilisation ulterieure dans les reacteurs a neutrons rapides plutot que de le recycler dans les reacteurs actuels a neutrons thermiques ou d'essayer de le vendre. Ce probleme a ete etudie dans le cadre d'un systeme de production d'energie electrique qui ne prevoirait pas la vente du plutonium produit par ses reacteurs nucleaires ni

Radiological safety aspects of handling plutonium

International Nuclear Information System (INIS)

Sundararajan, A.R.

2016-01-01

Department of Atomic Energy in its scheme of harnessing the nuclear energy for electrical power generation and strategic applications has given a huge role to utilization of plutonium. In the power production programme, fast reactors with plutonium as fuel are expected to play a major role. This would require establishing fuel reprocessing plants to handle both thermal and fast reactor fuels. So in the nuclear fuel cycle facilities variety of chemical, metallurgical, mechanical operations have to be carried out involving significant inventories of "2"3"9 Pu and associated radionuclides. Plutonium is the most radiotoxic radionuclide and therefore any facility handling it has to be designed and operated with utmost care. Two problems of major concern in the protection of persons working in plutonium handling facilities are the internal exposure to the operating personnel from uptake of plutonium and transplutonic nuclides as they are highly radiotoxic and the radiation exposure of hands and eye lens during fuel fabrication operations especially while handling recycled high burn up plutonium. In view of the fact that annual limit for intake is very small for "2"3"9Pu and its radiation emission characteristics are such that it is a huge challenge for the health physicists to detect Pu in air and in workers. This paper discusses the principles and practices followed in providing radiological surveillance to workers in plutonium handling areas. The challenges in protecting the workers from receiving exposures to hands and eye lens in handling high burn up plutonium are also discussed. The sites having Pu fuel cycle facilities should have trained medical staff to handle cases involving excessive intake of plutonium. (author)

Plutonium-induced lymphadenitis in beagles

International Nuclear Information System (INIS)

Dagle, G.E.; Park, J.F.

1976-01-01

Plutonium oxide particles accumulate in the tracheobronchial lymph nodes of beagles exposed by inhalation and in the popliteal lymph nodes after subcutaneous injection in the hind paws. The sequence of histopathologic changes after phagocytosis of particles included necrosis, increased numbers of macrophages, and fibroplasia. Scar tissue eventually replaced the normal architecture of the lymph nodes and sequestered the plutonium particles from surrounding parenchyma. Electron microscopy showed that plutonium particles were aggregated in phagolysosomes of macrophages

Guidelines for international plutonium management: Overview and implications

International Nuclear Information System (INIS)

Bryson, M.C.; Fitzgerald, C.P.; Kincaid, C.

1998-01-01

In September, 1997, nine of the world's plutonium-using countries agreed to a set of guidelines for international plutonium management, with acceptances to be submitted to the International Atomic Energy Agency on December 1. Following three years of discussion, the guidelines provide a unified package of accepted rules for the storage, handling, and transportation of civil plutonium as well as military plutonium that has been declared as no longer required for defense purposes. New requirements include a formal declaration of national plutonium strategies, which will recognize the environmental, economic, and proliferation concerns and the consequent importance of balancing plutonium supply and demand. Nations will also make annual declaration of their non-military stockpiles of unirradiated plutonium, together with estimates of the plutonium content in spent reactor fuel. These guidelines represent the first formally accepted recognition of the need for plutonium management of this scope and could thus provide a partial basis for future monitoring and policy regimes

Six-kilogram-scale electrorefining of plutonium metal

International Nuclear Information System (INIS)

Mullins, L.J.; Morgan, A.N.; Apgar, S.A. III; Christensen, D.C.

1982-09-01

The electrorefining of metallic plutonium scrap to produce high purity metal has been an established procedure at Los Alamos since 1964. This is a batch process and was limited to 4-kg plutonium because of criticality safety considerations. Improvements in critical mass measurements have permitted us to develop a process for 6-kg plutonium. The 6-kg process is now operational. The increased size of the process, together with other improvements which have been made, makes plutonium electrorefining the principal industrial tool for processing and purifying metallic plutonium scrap

Erosional losses of fallout plutonium

International Nuclear Information System (INIS)

Foster, G.R.; Hakonson, T.E.

1987-01-01

Plutonium from fallout after atmospheric explosion of nuclear weapons in the 1950's and 1960s is being redistributed over the landscape by soil erosion and carried on sediment by streams to oceans. Erosion rates computed with the Universal Soil Loss Equation for more than 200,000 sample points on nonfederal land across the US were used to estimate plutonium removal rates by soil erosion. On the average, only about 4% of the eroded sediment reaches the outlet of a major river. The remaining sediment is deposited en route, and because deposition is a selective process, the sediment is enriched in fine particles having the highest concentration of plutonium because of the element's strong association with clay and silt-sized sediment. Estimated enrichment ratios, sediment delivery ratios, and erosion rates were used to estimate annual delivery of fallout plutonium. These estimates ranged from 0.002% of the initial fallout plutonium inventory for the Savannah River basin to 0.01% for the Columbia River basin, to 0.02% for the Hudson and Rio Grande River basins, to 0.08% for the Mississippi River basin. If the deposition of plutonium had been uniformly 1 mCi/km 2 , the estimated plutonium activity on suspended sediment would range from about 7 fCi/g of sediment of the Savannah River basin, to 9 fCi/g for the Mississippi River basin, to 12 fCi/g for the Hudson River basin, to 14 fCi/g for the Columbia and Rio Grande River basins. 45 references, 2 figures, 17 tables

Plutonium story

International Nuclear Information System (INIS)

Seaborg, G.T.

1981-09-01

The first nuclear synthesis and identification (i.e., the discovery) of the synthetic transuranium element plutonium (isotope 238 Pu) and the demonstration of its fissionability with slow neutrons (isotope 239 Pu) took place at the University of California, Berkeley, through the use of the 60-inch and 37-inch cyclotrons, in late 1940 and early 1941. This led to the development of industrial scale methods in secret work centered at the University of Chicago's Metallurgical Laboratory and the application of these methods to industrial scale production, at manufacturing plants in Tennessee and Washington, during the World War II years 1942 to 1945. The chemical properties of plutonium, needed to devise the procedures for its industrial scale production, were studied by tracer and ultramicrochemical methods during this period on an extraordinarily urgent basis. This work, and subsequent investigations on a worldwide basis, have made the properties of plutonium very well known. Its well studied electronic structure and chemical properties give it a very interesting position in the actinide series of inner transition elements

Plutonium research and related activities at the Amarillo National Resource Center for Plutonium

International Nuclear Information System (INIS)

Hartley, R.S.; Beard, C.A.; Barnes, D.L.

1998-01-01

With the end of the Cold War, the US and Russia are reducing their nuclear weapons stockpiles. What to do with the materials from thousands of excess nuclear weapons is an important international challenge. How to handle the remaining US stockpile to ensure safe storage and reliability, in light of the aging support infrastructure, is an important national challenge. To help address these challenges and related issues, the Amarillo National Resource Center for Plutonium is working on behalf of the State of Texas with the US Department of Energy (DOE). The center directs three major programs that address the key aspects of the plutonium management issue: (1) the Communications, Education, Training and Community Involvement Program, which focuses on informing the public about plutonium and providing technical education at all levels; (2) the Environmental, Safety, and Health (ES and H) Program, which investigates the key ES and H impacts of activities related to the DOE weapons complex in Texas; and (3) the Nuclear and Other Materials Program, which is aimed at minimizing safety and proliferation risks by helping to develop and advocate safe stewardship, storage, and disposition of nuclear weapons materials. This paper provides an overview of the center's nuclear activities described in four broad categories of international activities, materials safety, plutonium storage, and plutonium disposition

An Improved Plutonium Trifluoride Precipitation Flowsheet

Energy Technology Data Exchange (ETDEWEB)

Harmon, H.D.

2001-06-26

This report discusses results of the plutonium trifluoride two-stage precipitation study. A series of precipitation experiments was used to identify the significant process variables affecting precipitation performance. A mathematical model of the precipitation process was developed which is based on the formation of plutonium fluoride complexes. The precipitation model relates all process variables, in a single equation, to a single parameter which can be used to control the performance of the plutonium trifluoride precipitation process. Recommendations have been made which will optimize the FB-Line plutonium trifluoride precipitation process.

An Improved Plutonium Trifluoride Precipitation Flowsheet

International Nuclear Information System (INIS)

Harmon, H.D.

2001-01-01

This report discusses results of the plutonium trifluoride two-stage precipitation study. A series of precipitation experiments was used to identify the significant process variables affecting precipitation performance. A mathematical model of the precipitation process was developed which is based on the formation of plutonium fluoride complexes. The precipitation model relates all process variables, in a single equation, to a single parameter which can be used to control the performance of the plutonium trifluoride precipitation process. Recommendations have been made which will optimize the FB-Line plutonium trifluoride precipitation process

Plutonium valence state distributions

International Nuclear Information System (INIS)

Silver, G.L.

1974-01-01

A calculational method for ascertaining equilibrium valence state distributions of plutonium in acid solutions as a function of the plutonium oxidation number and the solution acidity is illustrated with an example. The method may be more practical for manual use than methods based upon polynomial equations. (T.G.)

The first milligrams of plutonium

International Nuclear Information System (INIS)

Goldschmidt, B.

1996-01-01

This paper relates the discovery of the different plutonium chemical extraction processes in their historical context. The first experiments started during the second world war in 1942 with the American ''Metallurgical Laboratory'' project which brought together Arthur Compton, Enrico Fermi and Glenn Seaborg. During the same period, a competitive English-Canadian project, the ''Montreal Project'', was carried out to test different plutonium solvent extraction techniques. The author participated in both projects and joined the CEA in 1946, where he was in charge of the uranium and plutonium chemistry. By the end of 1949, his team could isolate the first milligrams of French plutonium from uranium oxide pellets of the ZOE reactor. In the beginning of 1952 he developed with his team the PUREX process. (J.S.)

Chloride removal from plutonium alloy

International Nuclear Information System (INIS)

Holcomb, H.P.

1983-01-01

SRP is evaluating a program to recover plutonium from a metallic alloy that will contain chloride salt impurities. Removal of chloride to sufficiently low levels to prevent damaging corrosion to canyon equipment is feasible as a head-end step following dissolution. Silver nitrate and mercurous nitrate were each successfully used in laboratory tests to remove chloride from simulated alloy dissolver solution containing plutonium. Levels less than 10 ppM chloride were achieved in the supernates over the precipitated and centrifuged insoluble salts. Also, less than 0.05% loss of plutonium in the +3, +4, or +6 oxidation states was incurred via precipitate carrying. These results provide impetus for further study and development of a plant-scale process to recover plutonium from metal alloy at SRP

Plutonium production and utilization forecasts in Europe

International Nuclear Information System (INIS)

Haijtink, B.

1976-01-01

The planned accelerated growth of nuclear energy generation in the near future will lead to a large production of plutonium in the thermal reactors. Therefore, up to 1985, the major part of the available plutonium will be plutonium recovered from spent uranium-metal, particularly in the United Kingdom and in France. Because of the low demand for fuelling the fast breeder reactors within the near future, a surplus of fissile plutonium will be accumulated in Europe. Even if the planned availability of the oxide reprocessing capacity will be delayed with two or three years, a plutonium surplus will still exist in Europe, e.g.; in 1985: 25-20 tons. On longer term, up to 2000, the plutonium production in thermal reactors will be sufficient to meet the estimated demand for fast breeder reactors at their commercial introduction foreseen for the nineties. That means that all the plutonium surplus needs not to be stocked for use in fast breeder reactors later on but could be recycled in thermal reactors. The magnitude of the available fissionable materials give an idea of the importance to promote, on an industrial scale, the plutonium recycling technology

Strategies for the plutonium utilization

International Nuclear Information System (INIS)

Zouain, D.M.; Lima, J.O.V.; Sakamoto, L.H.

1981-11-01

A review of the activities involving plutonium (its recycle, utilization and technological status and perspectives) is done. These informations are useful for an economic viability study for the plutonium utilization in thermal reactors (recycling) and in fast breeders reactor (FBR), trying to collect the major number of informations about these subjects. The initial phase describes the present status and projections of plutonium accumulation and requirements. Then, the technological process are described and some strategies are analyzed. (E.G.) [pt

Plutonium titration by controlled potential coulometry; Dosage du plutonium par coulometrie a potentiel impose

Energy Technology Data Exchange (ETDEWEB)

Leguay, N.

2011-07-01

The LAMMAN (Nuclear Materials Metrology Laboratory) is the support laboratory of the CETAMA (Analytical Method Committee), whose two main activities are developing analytic methods, and making and characterizing reference materials. The LAMMAN chose to develop the controlled potential coulometry because it is a very accurate analytical technique which allows the connection between the quantity of element electrolysed to the quantity of electricity measured thanks to the Faraday's law: it does not require the use of a chemical standard. This method was first used for the plutonium titration and was developed in the Materials Analysis and Metrology Laboratory (LAMM), for upgrading its performances and developing it to the titration of other actinides. The equipment and the material used were developed to allow the work in confined atmosphere (in a glove box), with all the restrictions involved. Plutonium standard solutions are used to qualify the method, and in particular to do titrations with an uncertainty better than 0.1 %. The present study allowed making a bibliographic research about controlled potential coulometry applied to the actinides (plutonium, uranium, neptunium, americium and curium). A full procedure was written to set all the steps of plutonium titration, from the preparation of samples to equipments storage. A method validation was done to check the full procedure, and the experimental conditions: working range, uncertainty, performance... Coulometric titration of the plutonium from pure solution (without interfering elements) was developed to the coulometric titration of the plutonium in presence of uranium, which allows to do accurate analyses for the analyses of some parts of the reprocessing of the spent nuclear fuel. The possibility of developing this method to other actinides than plutonium was highlighted thanks to voltammetric studies, like the coulometric titration of uranium with a working carbon electrode in sulphuric medium. (author)

Production of Plutonium Metal from Aqueous Solutions

Energy Technology Data Exchange (ETDEWEB)

Orth, D.A.

2003-01-16

The primary separation of plutonium from irradiated uranium by the Purex solvent extraction process at the Savannah River Plant produces a dilute plutonium solution containing residual fission products and uranium. A cation exchange process is used for concentration and further decontamination of the plutonium, as the first step in the final preparation of metal. This paper discusses the production of plutonium metal from the aqueous solutions.

Automation of plutonium spectrophotometry

International Nuclear Information System (INIS)

Perez, J.J.; Boisde, G.; Goujon de Beauvivier, M.; Chevalier, G.; Isaac, M.

1980-01-01

Instrumentation was designed and constructed for automatic control of plutonium by molecular absorption spectrophotometry, on behalf of the reprocessing facilities, to meet two objectives: on-line measurement, of the valency state of plutonium, on by-pass, with the measured concentration covering the process concentration range up to a few mg.l -1 ; laboratory measurement of plutonium adjusted to valency VI, with operation carried out using a preparative system meeting the required containment specifications. For this two objectives, the photometer, optical cell connections are made by optical fibers resistant to β, γ radiation. Except this characteristic the devices are different according to the quality required for result [fr

Civil plutonium amounts in the world

International Nuclear Information System (INIS)

Naudet, G.

1994-01-01

The experience of plutonium reprocessing in water reactors is positive and today the use of this nuclear fuel is at industrial level. Plutonium quantities in spent fuel go on increasing, plutonium stock coming from reprocessing can be controlled: according to conjuncture, it will evolve by stabilization or decreasing at the beginning of next century

Polyethylene-reflected plutonium metal sphere : subcritical neutron and gamma measurements.

Energy Technology Data Exchange (ETDEWEB)

Mattingly, John K.

2009-11-01

Numerous benchmark measurements have been performed to enable developers of neutron transport models and codes to evaluate the accuracy of their calculations. In particular, for criticality safety applications, the International Criticality Safety Benchmark Experiment Program (ICSBEP) annually publishes a handbook of critical and subcritical benchmarks. Relatively fewer benchmark measurements have been performed to validate photon transport models and codes, and unlike the ICSBEP, there is no program dedicated to the evaluation and publication of photon benchmarks. Even fewer coupled neutron-photon benchmarks have been performed. This report documents a coupled neutron-photon benchmark for plutonium metal reflected by polyethylene. A 4.5-kg sphere of ?-phase, weapons-grade plutonium metal was measured in six reflected configurations: (1) Bare; (2) Reflected by 0.5 inch of high density polyethylene (HDPE); (3) Reflected by 1.0 inch of HDPE; (4) Reflected by 1.5 inches of HDPE; (5) Reflected by 3.0 inches of HDPE; and (6) Reflected by 6.0 inches of HDPE. Neutron and photon emissions from the plutonium sphere were measured using three instruments: (1) A gross neutron counter; (2) A neutron multiplicity counter; and (3) A high-resolution gamma spectrometer. This report documents the experimental conditions and results in detail sufficient to permit developers of radiation transport models and codes to construct models of the experiments and to compare their calculations to the measurements. All of the data acquired during this series of experiments are available upon request.

Polyethylene-reflected plutonium metal sphere: subcritical neutron and gamma measurements

International Nuclear Information System (INIS)

Mattingly, John K.

2009-01-01

Numerous benchmark measurements have been performed to enable developers of neutron transport models and codes to evaluate the accuracy of their calculations. In particular, for criticality safety applications, the International Criticality Safety Benchmark Experiment Program (ICSBEP) annually publishes a handbook of critical and subcritical benchmarks. Relatively fewer benchmark measurements have been performed to validate photon transport models and codes, and unlike the ICSBEP, there is no program dedicated to the evaluation and publication of photon benchmarks. Even fewer coupled neutron-photon benchmarks have been performed. This report documents a coupled neutron-photon benchmark for plutonium metal reflected by polyethylene. A 4.5-kg sphere of ?-phase, weapons-grade plutonium metal was measured in six reflected configurations: (1) Bare; (2) Reflected by 0.5 inch of high density polyethylene (HDPE); (3) Reflected by 1.0 inch of HDPE; (4) Reflected by 1.5 inches of HDPE; (5) Reflected by 3.0 inches of HDPE; and (6) Reflected by 6.0 inches of HDPE. Neutron and photon emissions from the plutonium sphere were measured using three instruments: (1) A gross neutron counter; (2) A neutron multiplicity counter; and (3) A high-resolution gamma spectrometer. This report documents the experimental conditions and results in detail sufficient to permit developers of radiation transport models and codes to construct models of the experiments and to compare their calculations to the measurements. All of the data acquired during this series of experiments are available upon request.

Geomorphology of plutonium in the Northern Rio Grande

Energy Technology Data Exchange (ETDEWEB)

Graf, W.L. [Arizona Univ., Tempe, AZ (United States). Dept., of Geography

1993-03-01

Nearly all of the plutonium in the natural environment of the Northern Rio Grande is associated with soils and sediment, and river processes account for most of the mobility of these materials. A composite regional budget for plutonium based on multi-decadal averages for sediment and plutonium movement shows that 90 percent of the plutonium moving into the system is from atmospheric fallout. The remaining 10 percent is from releases at Los Alamos. Annual variation in plutonium flux and storage exceeds 100 percent. The contribution to the plutonium budget from Los Alamos is associated with relatively coarse sediment which often behaves as bedload in the Rio Grande. Infusion of these materials into the main stream were largest in 1951, 1952, 1957, and 1968. Because of the schedule of delivery of plutonium to Los Alamos for experimentation and weapons manufacturing, the latter two years are probably the most important. Although the Los Alamos contribution to the entire plutonium budget was relatively small, in these four critical years it constituted 71--86 percent of the plutonium in bedload immediately downstream from Otowi.

Geomorphology of plutonium in the Northern Rio Grande

International Nuclear Information System (INIS)

Graf, W.L.

1993-03-01

Nearly all of the plutonium in the natural environment of the Northern Rio Grande is associated with soils and sediment, and river processes account for most of the mobility of these materials. A composite regional budget for plutonium based on multi-decadal averages for sediment and plutonium movement shows that 90 percent of the plutonium moving into the system is from atmospheric fallout. The remaining 10 percent is from releases at Los Alamos. Annual variation in plutonium flux and storage exceeds 100 percent. The contribution to the plutonium budget from Los Alamos is associated with relatively coarse sediment which often behaves as bedload in the Rio Grande. Infusion of these materials into the main stream were largest in 1951, 1952, 1957, and 1968. Because of the schedule of delivery of plutonium to Los Alamos for experimentation and weapons manufacturing, the latter two years are probably the most important. Although the Los Alamos contribution to the entire plutonium budget was relatively small, in these four critical years it constituted 71--86 percent of the plutonium in bedload immediately downstream from Otowi

Method of stripping plutonium from tributyl phosphate solution which contains dibutyl phosphate-plutonium stable complexes

International Nuclear Information System (INIS)

Ochsenfeld, W.; Schmieder, H.

1976-01-01

Fast breeder fuel elements which have been highly burnt-up are reprocessed by extracting uranium and plutonium into an organic solution containing tributyl phosphate. The tributyl phosphate degenerates at least partially into dibutyl phosphate and monobutyl phosphate, which form stable complexes with tetravalent plutonium in the organic solution. This tetravalent plutonium is released from its complexed state and stripped into aqueous phase by contacting the organic solution with an aqueous phase containing tetravalent uranium. 6 claims, 1 drawing figure

Experimental Studies on Plutonium Kinetics in Marine Biota

International Nuclear Information System (INIS)

Fowler, S.; Heyraud, M.; Beasley, T.M.

1976-01-01

Laboratory experiments were undertaken to measure plutonium flux through marine organisms and to clarify the pathways by which this important element is cycled in the marine environment. The use of a specially prepared isotope, plutonium-237, allowed measurements to be made with standard Nal(Tl) scintillation techniques. Mussels, shrimp and worms were allowed to accumulate plutonium-237 from sea water for up to 25 days. Accumulation by shrimp was relatively slow and the degree of uptake was strongly influenced by moulting. Cast moults contained large fractions of the shrimps ' plutonium content, indicating the high affinity of plutonium for surface areas. Only small amounts of the isotope in the moult are lost to water; hence, moulting is considered to be an important biological parameter in the biogeochemical cycling of plutonium. Mussels attained higher concentration factors than shrimp with most of the accumulated isotope (> 80%) located in the shell. Byssus threads often contained large fractions of the mussels' plutonium-237 content and reached concentration factors as high as 4100. Worms readily accumulated plutonium-237 in either the +4 or +6 state, reaching concentration factors of approximately 200, Retention studies indicated a relatively slow loss of plutonium-237 from all animals studied. In the case of mussels, a computed half-time for a large fraction of the animals plutonium content was of the order of 2 years. The more rapid loss from shrimp (Tb 1/2 = 1.5 months) was due principally to the large fraction of plutonium lost at moult. Food chain studies with shrimp indicated that tissue build-up via plutonium ingestion would be a slow process. Total excretion was not entirely a result of passing contaminated food through the gut; approximately 15% of the ingested plutonium was removed from the contaminated food and subsequently excreted by processes other than defaecation of labelled food. Ratios of four different plutonium isotopes used in

Experimental studies on plutonium kinetics in marine biota

International Nuclear Information System (INIS)

Fowler, S.; Heyraud, M.; Beasley, T.M.

1975-01-01

Laboratory experiments were undertaken to measure plutonium flux through marine organisms and to clarify the pathways by which this important element is cycled in the marine environment. The use of a specially prepared isotope, plutonium-237, allowed measurements to be made with standard NaI(Tl) scintillation techniques. Mussels, shrimp and worms were allowed to accumulate plutonium-237 from seawater for up to 25 days. Accumulation by shrimp was relatively slow and the degree of uptake was strongly influenced by moulting. Cast moults contained large fractions of the shrimps' plutonium content, indicating the high affinity of plutonium for surface areas. Only small amounts of the isotope in the moult are lost to water; hence, moulting is considered to be an important biological parameter in the biogeochemical cycling of plutonium. Mussels attained higher concentration factors than shrimp with most of the accumulated isotope (>80%) located in the shell. Byssus threads often contained large fractions of the mussels' plutonium-237 content and reached concentration factors as high as 4100. Worms readily accumulated plutonium-237 in either the +4 or +6 state, reaching concentration factors of approximately 200. Retention studies indicated a relatively slow loss of plutonium-237 from all animals studied. In the case of mussels, a computed half-time for a large fraction of the animals' plutonium content was of the order of 2 years. The more rapid loss from shrimp (Tbsub(1/2)=1.5 months) was due principally to the large fraction of plutonium lost at moult. Food chain studies with shrimp indicated that tissue build-up via plutonium ingestion would be a slow process. Total excretion was not entirely a result of passing contaminated food through the gut; approximately 15% of the ingested plutonium was removed from the contaminated food and subsequently excreted by processes other than defaecation of labelled food. Ratios of four different plutonium isotopes used in the

Specification analysis of plutonium fuels : a potentiometric method for the determination of plutonium

International Nuclear Information System (INIS)

Vaidyanathan, S.; Natarajan, P.R.

1977-01-01

A potentiometric method for the routine determination of plutonium in the specification analysis of plutonium fuels is described. Plutonium is oxidized to Pu(VI) with AgO and Pu(VI) is reduced with Fe(II) after the destruction of excess AgO with sulphamic acid. The excess Fe(II) is titrated potentiometrically against K 2 Cr 2 O 7 , the titration being carried out by adding a concentrated titrant solution from a weight burette and a suitably diluted solution from another weight burette near the end. The overall relative standard deviation obtained in 326 analyses of a working standard solution by eight experimenters is 0.14 percent. (author)

Plutonium distribution in various components of natural organic matters and their role in plutonium migration in soils

Energy Technology Data Exchange (ETDEWEB)

Pavlotskaya, F.I.; Goryachenkova, T.A.

1987-09-01

The purpose of this work was to ascertain the links of plutonium with various components of the organic matter of different types of soils and their role in its migration in soils. The test objects were typical soils of forest and forest-steppe zones: sod-podzolic, gray forest, and leached chernozem contaminated with plutonium under laboratory conditions and stored in the air-dried state for three years, as also chernozem leached from an experimental site where agricultural plants were grown for a long time. The plutonium content in the fractions isolated from the contaminated soils was determined by its direct coprecipitation with microgram quantities of cerium hydroxide. The chemical yield of plutonium was determined by adding to a solution aliquot, equal to the analysis aliquot in volume, a known amount of plutonium and by its isolation under identical conditions. The ..gamma..-radiation of plutonium isolated on a nuclear filter with a pore size less than or equal to 15 ..mu..m was measured on a Protoka type gas flow counter.

Electrochemistry of plutonium in molten halides

International Nuclear Information System (INIS)

McCurry, L.E.; Moy, G.M.M.; Bowersox, D.F.

1987-01-01

The electrochemistry of plutonium in molten halides is of technological importance as a method of purification of plutonium. Previous authors have reported that plutonium can be purified by electrorefining impure plutonium in various molten haldies. Work to eluciate the mechanism of the plutonium reduction in molten halides has been limited to a chronopotentiometric study in LiCl-KCl. Potentiometric studies have been carried out to determine the standard reduction potential for the plutonium (III) couple in various molten alkali metal halides. Initial cyclic voltammetric experiments were performed in molten KCL at 1100 K. A silver/silver chloride (10 mole %) in equimolar NaCl-KCl was used as a reference electrode. Working and counter electrodes were tungsten. The cell components and melt were contained in a quartz crucible. Background cyclic voltammograms of the KCl melt at the tungsten electrode showed no evidence of electroactive impurities in the melt. Plutonium was added to the melt as PuCl/sub 3/, which was prepared by chlorination of the oxide. At low concentrations of PuCl/sub 3/ in the melt (0.01-0.03 molar), no reduction wave due to the reduction of Pu(III) was observed in the voltammograms up to the potassium reduction limit of the melt. However on scan reversal after scanning into the potassium reduction limit a new oxidation wave was observed

The Plutonium Temperature Effect Experimental Program

Energy Technology Data Exchange (ETDEWEB)

Haeck, Wim; Leclaire, Nicolas; Letang, Eric [IRSN, Fontenay-aux-Roses (France); Girault, Emmanuel; Fouillaud, Patrick [CEA, VALDUC (France)

2008-07-01

Various theoretical studies have shown that highly diluted plutonium solutions could have a positive temperature effect but (up to now) no experimental program has confirmed this effect. The main goal of the French Plutonium Temperature Effect Experimental Program (or PU+ in short) is to effectively show that such a positive temperature effect exists for diluted plutonium solutions. The experiments were conducted in the 'Apparatus B' facility at the CEA Valduc research centre in France and involved several sub-critical approach type of experiments using plutonium nitrate solutions with concentrations of 14.3, 15 and 20 g/l at temperatures ranging from 20 to 40 deg. C. A total number of 14 phase I experiments (consisting of independent subcritical approaches) have been performed (5 at 20 g/l, 4 at 15 g/l and 5 at 14.3 g/l) between 2006 and 2007. The impact of the uncertainties on the solution acidity and the plutonium concentration makes it difficult to clearly demonstrate the positive temperature effect, requiring an additional phase II experiment (in which the use of the same plutonium solution was ensured) from 22 to 28 deg. C performed in July 2007. This experiment has shown the existence of a positive temperature effect approx +2 pcm/deg. C (from 22 to 28 deg. C for a plutonium concentration of 14.3 g/l). (authors)

The distribution of plutonium-241 in rodents

International Nuclear Information System (INIS)

Priest, N.D.

1977-01-01

Plutonium-241 citrate solution at pH 6.5 was injected intravenously or intraperitoneally into hamsters and rats at a dose of 50 MBq kg -1 (1.35 mCi kg -1 ). The animals were killed 1 day or 1 week later, and tissues were removed for autoradiography and radiochemical analysis. Plutonium-241 was distributed in rats in the same way as plutonium-239, and is a suitable isotope for high-resolution tissue-section autoradiography. Plutonium deposits in cells consisted of a nuclear and a cytoplasmic component. In the hamster kidney cells, the amount associated with the nucleus was about 55 per cent of the total cellular plutonium at 24 hours after injection. Six days later, it was only about 30 per cent. Plutonium deposits were also characterized in hepatocytes, in the interstitial cells of the testes, in the cells of ovarian follicles, in chondrocytes and in bone cells, including osteoblasts and osteocytes. In bone there appeared to be both an extracellular and intracellular deposit. No evidence was found of substantial incorporation of plutonium into the mineral phase of bone. (author)

Plutonium Speciation, Solubilization and Migration in Soils

International Nuclear Information System (INIS)

Neu, M.; Runde, W.

1999-01-01

This report summarizes research completed in the first half of a three-year project. As outlined in the authors' proposal they are focusing on (1) characterizing the plutonium at an actinide contaminated site, RFETS, including determining the origin, dispersion, and speciation of the plutonium, (2) studying environmentally important plutonium complexes, primarily hydroxides and carbonates, and (3) examining the interactions of plutonium species with manganese minerals. In the first year the authors focused on site based studies. This year they continue to characterize samples from the RFETS, study the formation and structural and spectroscopic features of environmentally relevant Pu species, and begin modeling the environmental behavior of plutonium

Recent trends of plutonium facilities and their control

Energy Technology Data Exchange (ETDEWEB)

Muto, T [Power Reactor and Nuclear Fuel Development Corp., Tokai, Ibaraki (Japan). Tokai Works

1974-02-01

Much interest has been focussed on Pu recycle since the oil crisis because of an expected shortage of enriched uranium. Plutonium handling techniques and plutonium fuel fabricating facilities should be developed to meet the future demand of plutonium, but the radioactive property of plutonium to be reprocessed from spent fuel and recycled plutonium is remarkably different, and it has to be handled safely. Technical criteria for plutonium facilities are specified in the USAEC regulatory guides and other rules. Some of these criteria are location condition, quality of confinement, protection against accidents and so on. The control conditions for plutonium facilities are exposure control, criticality control, measurement control and new system of safeguard. These problems are under development to meet the future requirement for the safe handling of Pu material.

Plutonium Oxide Process Capability Work Plan

Energy Technology Data Exchange (ETDEWEB)

Meier, David E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Tingey, Joel M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2014-02-28

Pacific Northwest National Laboratory (PNNL) has been tasked to develop a Pilot-scale Plutonium-oxide Processing Unit (P3U) providing a flexible capability to produce 200g (Pu basis) samples of plutonium oxide using different chemical processes for use in identifying and validating nuclear forensics signatures associated with plutonium production. Materials produced can also be used as exercise and reference materials.

Long time contamination from plutonium

International Nuclear Information System (INIS)

Fueloep, M.; Patzeltova, N.; Ragan, P.; Matel, L.

1995-01-01

Plutonium isotopes in the organism of the patient (who had participated in the liquidation works after the Chernobyl accident; for three month he had stayed in the epicenter, where he acted as a chauffeur driving a radioactive material to the place of destination) from urine were determined. For determination of the concentration of Pu-239, Pu-240 in urine a modified radiochemical method was used. After mineralization the sample was separated as an anion-nitrate complex with contact by the anion form of the resin in the column. The resin was washed by 8 M HNO 3 , the 8 M HCl with 0.3 M HNO 3 for removing the other radionuclides. The solution 0.36 M HCl with 0.01 M HF was used for the elution of plutonium. Using the lanthanum fluoride technique the sample was filtrated through a membrane filter. The plutonium was detected in the dry sample. The Pu-239 tracer was used for the evaluation of the plutonium separation efficiency. The alpha spectrometric measurements were carried out with a large area silicon detector. The samples were measured and evaluated in the energy region 4.98-5.18 MeV. The detection limit of alpha spectrometry measurements has been 0.01 Bq dm -3 . The concentration of plutonium in the 24-hour urine was determined three times in the quarter year intervals. The results are: 54 mBq, 63.2 mBq, 53 mBq, with average 56,7 mBq. From the results of the analyses of plutonium depositions calculated according to ICRP 54 the intake of this radionuclide for the patient was 56.7 kBq. To estimate a committed effective dose (50 years) from the intake of plutonium was used a conversion factor 6.8.10 -5 Sv.Bq -1 (class W). So the expressed committed effective dose received from the plutonium intake is 3.8 Sv. This number is relatively high and all the effective dose will be higher, because the patient was exposed to the other radionuclides too. For example the determination of the rate radionuclides Am-241/Pu-239,Pu-240 was 32-36 % in the fallout after the Chernobyl

Plutonium gastrointestinal absorption by adults baboons

International Nuclear Information System (INIS)

Lataillade, G.; Madic, C.; Willemot, J.M.; Germain, P.; Colle, C.; Metivier, H.

1991-01-01

Gastrointestinal absorption of plutonium was investigated in baboons after ingestion of plutonium solution (oxidation states III; IV; V; VI), and plutonium incorporated in soya bean and winkles. We studied the effects of oxidation state and ingested mass for masses ranging from 0.35 μg to 51.6 x 10 +3 μg (4 x 10 -2 to 7776 μg of plutonium per kg of body weight). No clear increase in plutonium retention was shown for concentrations of plutonium smaller than 1 μg/kg. From 1 μg/kg to 1 mg/kg no effects of mass or oxidation state was observed and the mean fractional retention value was 10 -4 . For ingested masses higher than 1 mg/kg the fractional retention values respectively increased for Pu(V) and Pu(III) to (0.9 + 0.2) x 10 -2 and (7.4 + 4.1) x 10 -4 of the ingested mass. This increase might be due to the weak hydrolysis of these oxidation states which would increase gastrointestinal absorption by decrease of hydroxide formation. The fraction of plutonium retained after ingestion of soya bean was (3.0 + 0.5) x 10 -4 about 3 fold higher than the value for 238 Pu nitrate solution. No clear increase in plutonium retention was shown after ingestion of winkles containing 238 Pu. In conclusion, except for high masses of ingested Pu, the retention of which could reach 1% of the ingested dose, our results show that the gastrointestinal transfer factor of 10 -4 proposed by ICRP for gastrointestinal absorption of soluble form of Pu is acceptable, but 10 -3 would provide better safety margin [fr

Disposing of the world's excess plutonium

International Nuclear Information System (INIS)

McCormick, J.M.; Bullen, D.B.

1998-01-01

The authors undertake three key objectives in addressing the issue of plutonium disposition at the end of the Cold War. First, the authors estimate the total global inventory of plutonium both from weapons dismantlement and civil nuclear power reactors. Second, they review past and current policy toward handling this metal by the US, Russia, and other key countries. Third, they evaluate the feasibility of several options (but especially the vitrification and mixed oxide fuel options announced by the Clinton administration) for disposing of the increasing amounts of plutonium available today. To undertake this analysis, the authors consider both the political and scientific problems confronting policymakers in dealing with this global plutonium issue. Interview data with political and technical officials in Washington and at the International Atomic Energy Agency in Vienna, Austria, and empirical inventory data on plutonium from a variety of sources form the basis of their analysis

Selecting a plutonium vitrification process

Energy Technology Data Exchange (ETDEWEB)

Jouan, A. [Centre d`Etudes de la Vallee du Rhone, Bagnols sur Ceze (France)

1996-05-01

Vitrification of plutonium is one means of mitigating its potential danger. This option is technically feasible, even if it is not the solution advocated in France. Two situations are possible, depending on whether or not the glass matrix also contains fission products; concentrations of up to 15% should be achievable for plutonium alone, whereas the upper limit is 3% in the presence of fission products. The French continuous vitrification process appears to be particularly suitable for plutonium vitrification: its capacity is compatible with the required throughout, and the compact dimensions of the process equipment prevent a criticality hazard. Preprocessing of plutonium metal, to convert it to PuO{sub 2} or to a nitric acid solution, may prove advantageous or even necessary depending on whether a dry or wet process is adopted. The process may involve a single step (vitrification of Pu or PuO{sub 2} mixed with glass frit) or may include a prior calcination step - notably if the plutonium is to be incorporated into a fission product glass. It is important to weigh the advantages and drawbacks of all the possible options in terms of feasibility, safety and cost-effectiveness.

Plutonium in depleted uranium penetrators

International Nuclear Information System (INIS)

McLaughlin, J.P.; Leon-Vintro, L.; Smith, K.; Mitchell, P.I.; Zunic, Z.S.

2002-01-01

Depleted Uranium (DU) penetrators used in the recent Balkan conflicts have been found to be contaminated with trace amounts of transuranic materials such as plutonium. This contamination is usually a consequence of DU fabrication being carried out in facilities also using uranium recycled from spent military and civilian nuclear reactor fuel. Specific activities of 239+240 Plutonium generally in the range 1 to 12 Bq/kg have been found to be present in DU penetrators recovered from the attack sites of the 1999 NATO bombardment of Kosovo. A DU penetrator recovered from a May 1999 attack site at Bratoselce in southern Serbia and analysed by University College Dublin was found to contain 43.7 +/- 1.9 Bq/kg of 239+240 Plutonium. This analysis is described. An account is also given of the general population radiation dose implications arising from both the DU itself and from the presence of plutonium in the penetrators. According to current dosimetric models, in all scenarios considered likely ,the dose from the plutonium is estimated to be much smaller than that due to the uranium isotopes present in the penetrators. (author)

Decontaminaion of metals containing plutonium and americium

International Nuclear Information System (INIS)

Seitz, M.G.; Gerding, T.J.; Steindler, M.J.

1979-06-01

Melt-slagging (melt-refining) techniques were evaluated as a decontamination and consolidation step for metals contaminated with oxides of plutonium and americium. Experiments were performed in which mild steel, stainless steel, and nickel contaminated with oxides of plutonium and americium were melted in the presence of silicate slags of various compositions. The metal products were low in contamination, with the plutonium and americium strongly fractionated to the slags. Partition coefficients (plutonium in slag/plutonium in steel) of 7 x 10 6 were measured with boro-silicate slag and of 3 x 10 6 with calcium, magnesium silicate slag. Decontamination of metals containing as much as 14,000 ppM plutonium appears to be as efficient as for metals with plutonium levels of 400 ppM. Staged extraction, that is, a remelting of processed metal with clean slag, results in further decontamination of the metal. The second extraction is effective with either resistance-furnace melting or electric-arc melting. Slag adhering to the metal ingots and in defects within the ingots is in the important contributors to plutonium retained in processed metals. If these sources of plutonium are controlled, the melt-refining process can be used on a large scale to convert highly contaminated metals to homogeneous and compact forms with very low concentrations of plutonium and americium. A conceptual design of a melt-refining process to decontaminate plutonium- and americium-contaminated metals is described. The process includes single-stage refining of contaminated metals to produce a metal product which would have less than 10 nCi/g of TRU-element contamination. Two plant sizes were considered. The smaller conceptual plant processes 77 kg of metal per 8-h period and may be portable.The larger one processes 140 kg of metal per 8-h period, is stationary, and may be near te maximum size that is practical for a metal decontamination process

Assay of low-level plutonium effluents