Improving Heat Transfer at the Bottom of Vials for Consistent Freeze Drying with Unidirectional Structured Ice.

Science.gov (United States)

Rosa, Mónica; Tiago, João M; Singh, Satish K; Geraldes, Vítor; Rodrigues, Miguel A

2016-10-01

The quality of lyophilized products is dependent of the ice structure formed during the freezing step. Herein, we evaluate the importance of the air gap at the bottom of lyophilization vials for consistent nucleation, ice structure, and cake appearance. The bottom of lyophilization vials was modified by attaching a rectified aluminum disc with an adhesive material. Freezing was studied for normal and converted vials, with different volumes of solution, varying initial solution temperature (from 5°C to 20°C) and shelf temperature (from -20°C to -40°C). The impact of the air gap on the overall heat transfer was interpreted with the assistance of a computational fluid dynamics model. Converted vials caused nucleation at the bottom and decreased the nucleation time up to one order of magnitude. The formation of ice crystals unidirectionally structured from bottom to top lead to a honeycomb-structured cake after lyophilization of a solution with 4% mannitol. The primary drying time was reduced by approximately 35%. Converted vials that were frozen radially instead of bottom-up showed similar improvements compared with normal vials but very poor cake quality. Overall, the curvature of the bottom of glass vials presents a considerable threat to consistency by delaying nucleation and causing radial ice growth. Rectifying the vials bottom with an adhesive material revealed to be a relatively simple alternative to overcome this inconsistency.

Stability of tranexamic acid in 0.9% sodium chloride, stored in type 1 glass vials and ethylene/propylene copolymer plastic containers.

Science.gov (United States)

McCluskey, Susan V; Sztajnkrycer, Matthew D; Jenkins, Donald A; Zietlow, Scott P; Berns, Kathleen S; Park, Myung S

2014-01-01

Tranexamic acid has recently been demonstrated to decrease all-cause mortality and deaths due to hemorrhage in trauma patients. The optimal administration of tranexamic acid is within one hour of injury, but not more than three hours from the time of injury. To aid with timely administration, a premixed solution of 1 gram tranexamic acid and 0.9% sodium chloride was proposed to be stocked as a medication in both the aeromedical transport helicopters and Emergency Department at Mayo Clinic Hospital--Rochester Saint Marys Campus. Since no published stability data exists for tranexamic acid diluted with 0.9% sodium chloride, this study was undertaken to determine the stability of tranexamic acid diluted with 0.9% sodium chloride while being stored in two types of containers. Stability was determined through the use of a stability-indicating high-performance liquid reverse phase chromatography assay, pH, and visual tests. Tranexamic acid solutions of 1 gram in 0.9% sodium chloride 65 mL were studied at predetermined intervals for 90 days in ethylene/propylene copolymer plastic containers, protected from light, and at both controlled room and refrigerated temperatures. Tranexamic acid solutions of 1 gram in 0.9% sodium chloride 50 mL were studied at predetermined intervals for 180 days in clear Type 1 borosilicate glass vials sealed with intact elastomeric, Flourotec-coated stoppers, stored protected from light at controlled room temperature. Solutions stored in the ethylene/propylene copolymer plastic containers at both storage temperatures maintained at least 98% of initial potency throughout the 90-day study period. Solutions stored in glass vials at controlled room temperature maintained at least 92% of initial potency throughout the 180-day study period. Visual and pH tests revealed stable, clear, colorless, and particulate-free solutions throughout the respective study periods.

Artificial Leaks in Container Closure Integrity Testing: Nonlinear Finite Element Simulation of Aperture Size Originated by a Copper Wire Sandwiched between the Stopper and the Glass Vial.

Science.gov (United States)

Nieto, Alejandra; Roehl, Holger; Brown, Helen; Adler, Michael; Chalus, Pascal; Mahler, Hanns-Christian

2016-01-01

Container closure integrity (CCI) testing is required by different regulatory authorities in order to provide assurance of tightness of the container closure system against possible contamination, for example, by microorganisms. Microbial ingress CCI testing is performed by incubation of the container closure system with microorganisms under specified testing conditions. Physical CCI uses surrogate endpoints, such as coloration by dye solution ingress or gas flow (helium leakage testing). In order to correlate microbial CCI and physical CCI test methods and to evaluate the methods' capability to detect a given leak, artificial leaks are being introduced into the container closure system in a variety of different ways. In our study, artificial leaks were generated using inserted copper wires between the glass vial opening and rubber stopper. However, the insertion of copper wires introduces leaks of unknown size and shape. With nonlinear finite element simulations, the aperture size between the rubber stopper and the glass vial was calculated, depending on wire diameter and capping force. The dependency of the aperture size on the copper wire diameter was quadratic. With the data obtained, we were able to calculate the leak size and model leak shape. Our results suggest that the size as well as the shape of the artificial leaks should be taken into account when evaluating critical leak sizes, as flow rate does not, independently, correlate to hole size. Capping force also affected leak size. An increase in the capping force from 30 to 70 N resulted in a reduction of the aperture (leak size) by approximately 50% for all wire diameters. From 30 to 50 N, the reduction was approximately 33%. Container closure integrity (CCI) testing is required by different regulatory authorities in order to provide assurance of tightness of the container closure system against contamination, for example, by microorganisms. Microbial ingress CCI testing is performed by incubation of the

Polyethylene vials for liquid scintillation counters produced by the National Materials Research Institute

International Nuclear Information System (INIS)

Fiser, B.; Lukas, D.

1984-01-01

The properties were tested of polyethylene vials for liquid scintillation counters manufactured by the National Materials Research Institute. Liquid scintillation counter ISOCAP 300 by Nuclear Chicago was used for measuring. For unquenched samples, channel A was set up to 0.5-3.6 keV and channel B to 0.5-18 keV. The scintillation solution was prepared of toluene, 4 g PPO, 0.15 g POPOP per 1 l of toluene. CCl 4 was used as the quenching agent. Radioactive samples were prepared from 20 μl of standard solution of [ 3 H]-toluene with specific activity of 349 Bq/g. All measurements were made using a 7 ml scintillation solution into which radioactivity and possibly quenching agents were added. Potassium-free glass vials by SKLO UNION Teplice and thin-walled polyethylene vials by Nuclear Chicago were used for comparison. The background was measured, as were the time dependences of weight losses of the scintillation solution and carbon tetrachloride from the counting vials, changes in efficiency in channel B with time, changes in SCR with time and changes in the quenching curve with time. (E.S.)

The study of vial and cocktail for tritium radioactivity analysis of rain water by liquid scintillation counter

International Nuclear Information System (INIS)

Noh, Sung Jin; Kim, Hyo Jin; Kim, Hyun; Lee, Man Woo; Jeong, Dong Hyeok; Yang, Kwang Mo; Kang, Yeong Rok; Nam, Sang Hee

2015-01-01

Even though the current method for tritium (3H) analysis is routine, for the case of the low level of tritium in the environment, special conditions have to be fulfilled in order to obtain accurate and reliable tritium measurements. There are very little comparative data concerning commercial scintillating cocktails. The best cocktails for measuring tritium are those based on benzene derived solvent, and the worse cocktails are those which have complex chemical composition or contain too small concentration of scintillators. The aim of study was to investigate various vials and cocktails by comparison with the combination of few different scintillation cocktails and vials in our routine measurements according to count, efficiency, and the figure of merit (FOM). The comparison of three types of vials with scintillation cocktails for tritium activity analysis of rain water shows that glass vials have higher count rates and HiSafe 3 cocktails have lower FOM

A flexible system to capture sample vials in a storage box - the box vial scanner.

Science.gov (United States)

Nowakowski, Steven E; Kressin, Kenneth R; Deick, Steven D

2009-01-01

Tracking sample vials in a research environment is a critical task and doing so efficiently can have a large impact on productivity, especially in high volume laboratories. There are several challenges to automating the capture process, including the variety of containers used to store samples. We developed a fast and robust system to capture the location of sample vials being placed in storage that allows the laboratories the flexibility to use sample containers of varying dimensions. With a single scan, this device captures the box identifier, the vial identifier and the location of each vial within a freezer storage box. The sample vials are tracked through a barcode label affixed to the cap while the boxes are tracked by a barcode label on the side of the box. Scanning units are placed at the point of use and forward data to a sever application for processing the scanned data. Scanning units consist of an industrial barcode reader mounted in a fixture positioning the box for scanning and providing lighting during the scan. The server application transforms the scan data into a list of storage locations holding vial identifiers. The list is then transferred to the laboratory database. The box vial scanner captures the IDs and location information for an entire box of sample vials into the laboratory database in a single scan. The system accommodates a wide variety of vials sizes by inserting risers under the sample box and a variety of storage box layouts are supported via the processing algorithm on the server.

Spectral response of spider mite infested cotton: Mite density and miticide rate study

Science.gov (United States)

Two-spotted spider mites are important pests in many agricultural systems. Spider mites (Acari: Tetranychidae) have been found to cause economic damage in corn, cotton, and sorghum. Adult glass vial bioassays indicate that Temprano™ (abamectin) is the most toxic technical miticide for adult two-spot...

Enzyme stabilization by glass-derived silicates in glass-exposed aqueous solutions

Science.gov (United States)

Ives, J.A.; Moffett, J.R.; Arun, P.; Lam, D.; Todorov, T.I.; Brothers, A.B.; Anick, D.J.; Centeno, J.; Namboodiri, M.A.A.; Jonas, W.B.

2010-01-01

Objectives: To analyze the solutes leaching from glass containers into aqueous solutions, and to show that these solutes have enzyme activity stabilizing effects in very dilute solutions. Methods: Enzyme assays with acetylcholine esterase were used to analyze serially succussed and diluted (SSD) solutions prepared in glass and plastic containers. Aqueous SSD preparations starting with various solutes, or water alone, were prepared under several conditions, and tested for their solute content and their ability to affect enzyme stability in dilute solution. Results: We confirm that water acts to dissolve constituents from glass vials, and show that the solutes derived from the glass have effects on enzymes in the resultant solutions. Enzyme assays demonstrated that enzyme stability in purified and deionized water was enhanced in SSD solutions that were prepared in glass containers, but not those prepared in plastic. The increased enzyme stability could be mimicked in a dose-dependent manner by the addition of silicates to the purified, deionized water that enzymes were dissolved in. Elemental analyses of SSD water preparations made in glass vials showed that boron, silicon, and sodium were present at micromolar concentrations. Conclusions: These results show that silicates and other solutes are present at micromolar levels in all glass-exposed solutions, whether pharmaceutical or homeopathic in nature. Even though silicates are known to have biological activity at higher concentrations, the silicate concentrations we measured in homeopathic preparations were too low to account for any purported in vivo efficacy, but could potentially influence in vitro biological assays reporting homeopathic effects. ?? 2009 The Faculty of Homeopathy.

Drawing medicine out of a vial

Science.gov (United States)

... top. Then push gently on the plunger to push the air bubbles back into the vial. If you have a lot of bubbles, push the plunger to push all the medicine back into the vial. Draw medicine out again slowly ...

Estudio de la siniestralidad vial y diagnóstico de la seguridad vial en el campus de la Universidad de Alicante

OpenAIRE

Martínez Carrillo, Alba

2018-01-01

Este trabajo se ocupa del análisis de la siniestralidad vial y diagnóstico de la seguridad vial en el Campus de la Universidad de Alicante. Para ello, se emplean datos referentes a la accidentalidad vial ocurridos dentro del campus del año 2009 a octubre de 2016, obtenidos gracias a los partes de accidentes facilitados por el Departamento de Seguridad de la Universidad de Alicante. Junto al análisis de esta información, se ha llevado a cabo un trabajo de campo orientado a la seguridad vial pa...

Delamination propensity of pharmaceutical glass containers by accelerated testing with different extraction media.

Science.gov (United States)

Guadagnino, Emanuel; Zuccato, Daniele

2012-01-01

The delamination of pharmaceutical glass is a serious issue, as it can cause glass particles to appear in vials, a problem that has forced a number of drug product recalls in recent years. In Type I pharmaceutical glass vials, delamination occurs generally at the bottom and shoulder, where extensive flaming during the conversion process can favor a strong evaporation of alkali and borate species and the formation of heavily enriched silica layers. The contact with parenteral preparations dissolved in an alkaline medium increases the rate of glass corrosion, while the differential hydration of these layers can cause the detachment of flakes. The purpose of this study was to investigate the effect of the pH and the composition of the extraction solutions on the propensity of different glass types to delaminate. Repeated autoclave extractions at 121 °C were carried out on different glass types with different extraction media, including organic extractants like citric and glutaric acid. When vials were in contact with alkaline solutions and similarly aggressive media, an increase in silica extraction values indicated glass corrosion and an increasing risk for further delamination. Under such conditions expansion 33 glass is extensively corroded, showing high silica concentration and heavy flaking as compared to other glass types. Sulfur-treated glass also showed early flaking, even if SiO(2) concentration was very low. A similar ranking was observed with extractions carried out with glutaric and citric acids, but at far much higher SiO(2) concentration levels. Extractions with 0.9% KCl solution can be used as an accelerated test to highlight the propensity of a glass to delaminate, but in no case it can be taken as a guarantee that the glass will not delaminate when exposed to the pharmaceutical drug, whose extraction ability requires case-by-case study. How can injectable drug manufacturers prevent glass delamination? The issue of delamination is a serious one, as it

The pharmaceutical vial capping process: Container closure systems, capping equipment, regulatory framework, and seal quality tests.

Science.gov (United States)

Mathaes, Roman; Mahler, Hanns-Christian; Buettiker, Jean-Pierre; Roehl, Holger; Lam, Philippe; Brown, Helen; Luemkemann, Joerg; Adler, Michael; Huwyler, Joerg; Streubel, Alexander; Mohl, Silke

2016-02-01

Parenteral drug products are protected by appropriate primary packaging to protect against environmental factors, including potential microbial contamination during shelf life duration. The most commonly used CCS configuration for parenteral drug products is the glass vial, sealed with a rubber stopper and an aluminum crimp cap. In combination with an adequately designed and controlled aseptic fill/finish processes, a well-designed and characterized capping process is indispensable to ensure product quality and integrity and to minimize rejections during the manufacturing process. In this review, the health authority requirements and expectations related to container closure system quality and container closure integrity are summarized. The pharmaceutical vial, the rubber stopper, and the crimp cap are described. Different capping techniques are critically compared: The most common capping equipment with a rotating capping plate produces the lowest amount of particle. The strength and challenges of methods to control the capping process are discussed. The residual seal force method can characterize the capping process independent of the used capping equipment or CCS. We analyze the root causes of several cosmetic defects associated with the vial capping process. Copyright © 2015 Elsevier B.V. All rights reserved.

Effect of Air Space in Storage Vials on Motility of Spermatozoa in Chilled Buck Semen

Directory of Open Access Journals (Sweden)

Magnus Paul K and Lali F Anand 1

Full Text Available This study was conducted in order to find out the effect of air space on the top of glass vial in which semen is stored, on the motility of spermatozoa. 45 samples collected from two bucks over a span of 6 months were used for experiment. Goat milk extender was the diluent used. Two ml each of diluted semen after noting their initial motility was stored in 2 ml and 5 ml vials. Samples were stored at 5°C and motility of spermatozoa noted at 24 and 48 hours. Semen without air space was found to preserve the motility better than semen with air space on 24 and 48 hours of incubation. This could be better attributed to reactive oxygen species production by the spermatozoa, but further investigation is needed in this aspect to confirm it. [Veterinary World 2010; 3(9.000: 421-423

High-throughput mosquito and fly bioassay system for natural and artificial substrates treated with residual insecticides.

Science.gov (United States)

Aldridge, Robert L; Wynn, W Wayne; Britch, Seth C; Allan, Sandra A; Walker, Todd W; Geden, Christopher J; Hogsette, Jerome A; Linthicum, Kenneth J

2013-03-01

A high-throughput bioassay system to evaluate the efficacy of residual pesticides against mosquitoes and muscid flies with minimal insect handling was developed. The system consisted of 4 components made of readily available materials: 1) a CO2 anaesthetizing chamber, 2) a specialized aspirator, 3) a cylindrical flat-bottomed glass bioassay chamber assembly, and 4) a customized rack.

Determination of moisture content in lyophilized mannitol through intact glass vials using NIR micro-spectrometers

Directory of Open Access Journals (Sweden)

Cristian Rodrigo Muzzio

2011-06-01

Full Text Available Determination of moisture content in lyophilized solids is fundamental to predict quality and stability of freeze-dried products, but conventional methods are time-consuming, invasive and destructive. The aim of this study was to develop and optimize a fast, inexpensive, noninvasive and nondestructive method for determination of moisture content in lyophilized mannitol, based on an NIR micro-spectrometer instead of a conventional NIR spectrometer. Measurements of lyophilized mannitol were performed through the bottom of rotating glass vials by means of a reflectance probe. The root mean standard error of prediction (RMSEP and the correlation coefficient (R²pred, yielded by the pre-treatments and calibration method proposed, was 0.233% (w/w and 0.994, respectively.A determinação do conteúdo de umidade em sólidos liofilizados é fundamental para se prever a qualidade e a estabilidade de produtos liofilizados, mas os métodos convencionais consomem muito tempo, são invasivos e destrutivos. O objetivo desse estudo foi desenvolver e otimizar um método rápido, econômico, não invasivo e não destrutivo para a determinação do conteúdo de umidade em manitol liofilizado, com base em microespectrômetro de infravermelho próximo ao invés de um espectrômetro de infravermelho próximo convencional. As medidas de manitol liofilizado foram realizadas através do fundo de recipiente de vidro em rotação por meio de sonda de reflectância. A raíz do erro médio padrão de predição (RMSEP e o coeficiente de correlação (R²pred obtidos pelo prétratamento e pelo método de calibração proposto foram, respectivamente, 0,233% (p/p e 0,994.

Evaluation of the open vial method in the radon measurement; Evaluacion del metodo del vial abierto en la medicion de radon

Energy Technology Data Exchange (ETDEWEB)

Lopez del Rio, H.; Davila R, J. I.; Mireles G, F., E-mail: hlopezdelrio@hotmail.com [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas (Mexico)

2014-10-15

The open vial method is a simple technique, under-utilized but that take advantage of the great radon solubility in organic solvents, therefore applies in the measurement of the radon concentration exhaled in soil. The method consists on the exposition to the gas radon of an open vial with scintillating solution. An integral mathematical model for indoors that describes the emanation processes and gas radon exhalation was developed, as well as the radon dissolution in the scintillation liquid, besides obtaining the characteristic parameters of the experimental system proposed for the radon concentration calculation exhaled by soils. Two experimental arrangements were designed with exposition cameras of 12 and 6 L and quantity of different soil. The open vial was prepared with a mixture of 8 ml of deionized water and 12 ml of scintillation liquid OptiPhase Hi Safe 3 in polyethylene vials; the measurements of the dissolved radon were carried out in scintillation liquid equipment. As a result, on average 2.0% of the exhaled radon is dissolved in the open vial and the dissolved fraction is independent of the experimental arrangement. Also was observed that the exposition time does not affect the radon dissolution significantly, in correspondence with the reported in the literature. (Author)

Analysis of pressurization of plutonium oxide storage vials during a postulated fire

Energy Technology Data Exchange (ETDEWEB)

Laurinat, J.; Kesterson, M.; Hensel, S.

2015-02-10

The documented safety analysis for the Savannah River Site evaluates the consequences of a postulated 1000 °C fire in a glovebox. The radiological dose consequences for a pressurized release of plutonium oxide powder during such a fire depend on the maximum pressure that is attained inside the oxide storage vial. To enable evaluation of the dose consequences, pressure transients and venting flow rates have been calculated for exposure of the storage vial to the fire. A standard B vial with a capacity of approximately 8 cc was selected for analysis. The analysis compares the pressurization rate from heating and evaporation of moisture adsorbed onto the plutonium oxide contents of the vial with the pressure loss due to venting of gas through the threaded connection between the vial cap and body. Tabulated results from the analysis include maximum pressures, maximum venting velocities, and cumulative vial volumes vented during the first 10 minutes of the fire transient. Results are obtained for various amounts of oxide in the vial, various amounts of adsorbed moisture, different vial orientations, and different surface fire exposures.

The effect of cool water pack preparation on vaccine vial temperatures in refrigerators.

Science.gov (United States)

Goldwood, Geneva; Diesburg, Steven

2018-01-02

Cool water packs are a useful alternative to ice packs for preventing unintentional freezing of vaccines during outreach in some situations. Current guidelines recommend the use of a separate refrigerator for cooling water packs from ambient temperatures to prevent possible heat degradation of adjacent vaccine vials. To investigate whether this additional equipment is necessary, we measured the temperatures that vaccine vials were exposed to when warm water packs were placed next to vials in a refrigerator. We then calculated the effect of repeated vial exposure to those temperatures on vaccine vial monitor status to estimate the impact to the vaccine. Vials were tested in a variety of configurations, varying the number and locations of vials and water packs in the refrigerator. The calculated average percentage life lost during a month of repeated warming ranged from 20.0% to 30.3% for a category 2 (least stable) vaccine vial monitor and from 3.8% to 6.0% for a category 7 (moderate stability) vaccine vial monitor, compared to 17.0% for category 2 vaccine vial monitors and 3.1% for category 7 vaccine vial monitors at a constant 5 °C. The number of vials, number of water packs, and locations of each impacted vial warming and therefore percentage life lost, but the vaccine vial monitor category had a higher impact on the average percentage life lost than any of the other parameters. The results suggest that damage to vaccines from repeated warming over the course of a month is not certain and that cooling water packs in a refrigerator where vaccines are being stored may be a useful practice if safe procedures are established. Copyright © 2017 The Author(s). Published by Elsevier Ltd.. All rights reserved.

A new bioassay for the ecotoxicological testing of VOCs on groundwater invertebrates and the effects of toluene on Niphargus inopinatus

Energy Technology Data Exchange (ETDEWEB)

Avramov, Maria; Schmidt, Susanne I. [Helmholtz Zentrum München, German Research Center for Environmental Health, Institute of Groundwater Ecology, Ingolstädter Landstrasse 1, D-85764 Neuherberg (Germany); Griebler, Christian, E-mail: christian.griebler@helmholtz-muenchen.de [Helmholtz Zentrum München, German Research Center for Environmental Health, Institute of Groundwater Ecology, Ingolstädter Landstrasse 1, D-85764 Neuherberg (Germany)

2013-04-15

Highlights: ► A new bioassay for testing the toxicity of VOCs on groundwater fauna is presented. ► Results on the toxicity of toluene to Niphargus inopinatus are now available. ► Henry equilibrium needs to be considered when bioassays with VOCs are designed. ► Methodological aspects related to “difficult-to-test substances” are discussed. -- Abstract: A protocol was developed for testing the ecotoxicological effects of volatile organic compounds (VOCs) on groundwater invertebrates. Test substance volatility was addressed in a “closed from start to analysis”-design. Since manifestation of toxic effects may be delayed in ‘slower metabolizing’ organisms such as groundwater fauna, a time-independent (TI-) approach was adopted. Toluene was used as a model substance and its toxicity to the groundwater amphipod Niphargus inopinatus was assessed as an example. The method evaluation process considered various methodological issues such as partitioning of the toxicant between the water and the gas phase (Henry equilibrium), the possible depletion of oxygen in closed test vials, as well as microbial biodegradation of the test substance. For N. inopinatus, an LC{sub 50},{sub 14} {sub days} of 46.6 mg L{sup −1} toluene was obtained. The ultimate LC{sub 50} value was estimated at 23.3 mg L{sup −1} toluene. No oxygen depletion occurred in the test vials and Henry equilibrium was found to be established after 6 h. The new test system proposed now awaits broad practical application.

Vial usage, device dead space, vaccine wastage, and dose accuracy of intradermal delivery devices for inactivated poliovirus vaccine (IPV).

Science.gov (United States)

Jarrahian, Courtney; Rein-Weston, Annie; Saxon, Gene; Creelman, Ben; Kachmarik, Greg; Anand, Abhijeet; Zehrung, Darin

2017-03-27

Intradermal delivery of a fractional dose of inactivated poliovirus vaccine (IPV) offers potential benefits compared to intramuscular (IM) delivery, including possible cost reductions and easing of IPV supply shortages. Objectives of this study were to assess intradermal delivery devices for dead space, wastage generated by the filling process, dose accuracy, and total number of doses that can be delivered per vial. Devices tested included syringes with staked (fixed) needles (autodisable syringes and syringes used with intradermal adapters), a luer-slip needle and syringe, a mini-needle syringe, a hollow microneedle device, and disposable-syringe jet injectors with their associated filling adapters. Each device was used to withdraw 0.1-mL fractional doses from single-dose IM glass vials which were then ejected into a beaker. Both vial and device were weighed before and after filling and again after expulsion of liquid to record change in volume at each stage of the process. Data were used to calculate the number of doses that could potentially be obtained from multidose vials. Results show wide variability in dead space, dose accuracy, overall wastage, and total number of doses that can be obtained per vial among intradermal delivery devices. Syringes with staked needles had relatively low dead space and low overall wastage, and could achieve a greater number of doses per vial compared to syringes with a detachable luer-slip needle. Of the disposable-syringe jet injectors tested, one was comparable to syringes with staked needles. If intradermal delivery of IPV is introduced, selection of an intradermal delivery device can have a substantial impact on vaccine wasted during administration, and thus on the required quantity of vaccine that needs to be purchased. An ideal intradermal delivery device should be not only safe, reliable, accurate, and acceptable to users and vaccine recipients, but should also have low dead space, high dose accuracy, and low overall

Device for treating plastic counting vials containing radioactive liquids

International Nuclear Information System (INIS)

Neidhart, B.; Brindoepke, H.W.; Flocke, W.; Kringe, K.P.; Lippmann, C.H.

1985-01-01

The treatment consists of separating the radioactive contents of the counting vial from its plastic components. The apparatus consists of a device for continuously supplying the counting vials to be treated, a means for crushing the vials into chips of plastic and a facility by means of which the radioactive contents of the counting vial and the separated plastic chips are collected separately from one another. A stirring assembly with a motor-driven stirrer and an alignment device are also provided. The radioactive substances pass through a sieve while the plastic chips slide down the sieve chute and into another container. All the metal parts of the facility are of stainless steel. The plastic chips collected in the sieve holder are washed and, after drying, are removed as negligibly radioactive solids. The weakly radioactive wash liquid is separated and collected. (orig./PW)

Optimizing human semen cryopreservation by reducing test vial volume and repetitive test vial sampling

DEFF Research Database (Denmark)

Jensen, Christian F S; Ohl, Dana A; Parker, Walter R

2015-01-01

OBJECTIVE: To investigate optimal test vial (TV) volume, utility and reliability of TVs, intermediate temperature exposure (-88°C to -93°C) before cryostorage, cryostorage in nitrogen vapor (VN2) and liquid nitrogen (LN2), and long-term stability of VN2 cryostorage of human semen. DESIGN......: Prospective clinical laboratory study. SETTING: University assisted reproductive technology (ART) laboratory. PATIENT(S): A total of 594 patients undergoing semen analysis and cryopreservation. INTERVENTION(S): Semen analysis, cryopreservation with different intermediate steps and in different volumes (50......-1,000 μL), and long-term storage in LN2 or VN2. MAIN OUTCOME MEASURE(S): Optimal TV volume, prediction of cryosurvival (CS) in ART procedure vials (ARTVs) with pre-freeze semen parameters and TV CS, post-thaw motility after two- or three-step semen cryopreservation and cryostorage in VN2 and LN2. RESULT...

Detection of Reduced Susceptibility to Chlorfenapyr- and Bifenthrin-Containing Products in Field Populations of the Bed Bug (Hemiptera: Cimicidae).

Science.gov (United States)

Ashbrook, Aaron R; Scharf, Michael E; Bennett, Gary W; Gondhalekar, Ameya D

2017-06-01

Insecticide resistance is a major impediment for effective control of Cimex lectularius L. Previous resistance detection studies with bed bugs have focused on certain pyrethroid, neonicotinoid, organochlorine, organophosphate, and carbamate insecticides. Within the pyrethroid class, resistance studies have mostly been limited to deltamethrin, lambda-cyhalothrin, and alpha- and beta-cyfluthrin. The goal of this study was to develop diagnostic concentration bioassays for assessing bed bug susceptibility levels to chlorfenapyr- and bifenthrin-containing products. First, glass vial and filter paper bioassay methods were compared for their utility in susceptibility monitoring. Statistical comparison of toxicity data between bioassays indicated that the vial assay was less confounded by assay susbtrate effects, required less insecticide, and was faster, especially for chlorfenapyr. Next, using vial diagnostic concentrations (LC99) for each insecticide, 10 laboratory-adapted field strains and the Harlan lab-susceptible strain were screened for susceptibility to chlorfenapyr and bifenthrin. The results of this study reveal recent bed bug susceptibility levels to certain chlorfenapyr- and bifenthrin-containing products. Reduced susceptibility was detected in three and five field strains to chlorfenapyr and bifenthrin, respectively. Detection of reduced susceptibility suggests that certain strains may be segregating toward greater chlorfenapyr and bifenthrin resistance. These results merit continuous resistance monitoring efforts to detect chlorfenapyr and bifenthrin susceptibility shifts. Additionally, to reduce insecticide selection pressures and delay resistance development, adoption of integrated bed bug control strategies that combine chemical and nonchemical methods is recommended. © The Authors 2017. Published by Oxford University Press on behalf of Entomological Society of America. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

Economic and microbiologic evaluation of single-dose vial extension for hazardous drugs.

Science.gov (United States)

Rowe, Erinn C; Savage, Scott W; Rutala, William A; Weber, David J; Gergen-Teague, Maria; Eckel, Stephen F

2012-07-01

The update of US Pharmacopeia Chapter in 2008 included guidelines stating that single-dose vials (SDVs) opened and maintained in an International Organization for Standardization Class 5 environment can be used for up to 6 hours after initial puncture. A study was conducted to evaluate the cost of discarding vials after 6 hours and to further test sterility of vials beyond this time point, subsequently defined as the beyond-use date (BUD). Financial determination of SDV waste included 2 months of retrospective review of all doses prescribed. Additionally, actual waste log data were collected. Active and control vials (prepared using sterilized trypticase soy broth) were recovered, instead of discarded, at the defined 6-hour BUD. The institution-specific waste of 19 selected SDV medications discarded at 6 hours was calculated at $766,000 annually, and tracking waste logs for these same medications was recorded at $770,000 annually. Microbiologic testing of vial extension beyond 6 hours showed that 11 (1.86%) of 592 samples had one colony-forming unit on one of two plates. Positive plates were negative at subsequent time points, and all positives were single isolates most likely introduced during the plating process. The cost of discarding vials at 6 hours was significant for hazardous medications in a large academic medical center. On the basis of microbiologic data, vial BUD extension demonstrated a contamination frequency of 1.86%, which likely represented exogenous contamination; vial BUD extension for the tested drugs showed no growth at subsequent time points and could provide an annual cost savings of more than $600,000.

Evaluation of the open vial method in the radon measurement

International Nuclear Information System (INIS)

Lopez del Rio, H.; Davila R, J. I.; Mireles G, F.

2014-10-01

The open vial method is a simple technique, under-utilized but that take advantage of the great radon solubility in organic solvents, therefore applies in the measurement of the radon concentration exhaled in soil. The method consists on the exposition to the gas radon of an open vial with scintillating solution. An integral mathematical model for indoors that describes the emanation processes and gas radon exhalation was developed, as well as the radon dissolution in the scintillation liquid, besides obtaining the characteristic parameters of the experimental system proposed for the radon concentration calculation exhaled by soils. Two experimental arrangements were designed with exposition cameras of 12 and 6 L and quantity of different soil. The open vial was prepared with a mixture of 8 ml of deionized water and 12 ml of scintillation liquid OptiPhase Hi Safe 3 in polyethylene vials; the measurements of the dissolved radon were carried out in scintillation liquid equipment. As a result, on average 2.0% of the exhaled radon is dissolved in the open vial and the dissolved fraction is independent of the experimental arrangement. Also was observed that the exposition time does not affect the radon dissolution significantly, in correspondence with the reported in the literature. (Author)

Determination of leachable arsenic from glass ampoules

International Nuclear Information System (INIS)

Kayasth, S.R.; Swain, K.K.

2004-01-01

Appreciable amounts of different arsenic compounds are used in the manufacture of glass and glass ampoules (injection vials and bottles) used to store drugs. Exposure/intake of arsenic to human beings may result in skin ulceration, injury to mucous membranes, perforation of nasal septum, skin cancer and keratoses, especially of the palms and soles and may cause detrimental effects. Considering the toxicity of arsenic, even if traces of arsenic from such glass containers/ampoules are leached out, it can impart damage to human beings. To check the possibility of leaching of arsenic from glass ampoules, a simple methodology has been developed. Different makes and varieties of glass ampoules filled with de-ionized water were subjected to high pressure and temperature leaching for varying amount of time using autoclave to create extreme conditions for the maximum leaching out of the analyte. Subsequently, the determination of the arsenic contents in leached water using neutron activation analysis is reported in detail with observations. (author)

Through-vial impedance spectroscopy of the mechanisms of annealing in the freeze-drying of maltodextrin: the impact of annealing hold time and temperature on the primary drying rate.

Science.gov (United States)

Smith, Geoff; Arshad, Muhammad Sohail; Polygalov, Eugene; Ermolina, Irina

2014-06-01

The study aims to investigate the impact of annealing hold time and temperature on the primary drying rate/duration of a 10% (w/v) solution of maltodextrin with an emphasis on how the mechanisms of annealing might be understood from the in-vial measurements of the ice crystal growth and the glass transition. The electrical impedance of the solution within a modified glass vial was recorded between 10 and 10(6) Hz during freeze-drying cycles with varying annealing hold times (1-5 h) and temperatures. Primary drying times decreased by 7%, 27% and 34% (1.1, 4.3 and 5.5 h) with the inclusion of an annealing step at temperatures of -15°C, -10°C and -5°C, respectively. The glass transition was recorded at approximately -16°C during the re-heating and re-cooling steps, which is close to the glass transition (Tg ') reported for 10% (w/v) maltodextrin and therefore indicates that a maximum freeze concentration (∼86%, w/w, from the Gordon-Taylor equation) was achieved during first freezing, with no further ice being formed on annealing. This observation, coupled to the decrease in electrical resistance that was observed during the annealing hold time, suggests that the reduction in the drying time was because of improved connectivity of ice crystals because of Ostwald ripening rather than devitrification. © 2014 Wiley Periodicals, Inc. and the American Pharmacists Association.

Inventarios viales y categorización de la red vial en estudios de Ingeniería de Tránsito y Transporte

Directory of Open Access Journals (Sweden)

Julián Rodrigo Quintero

2011-03-01

Full Text Available Se presentan las principales consideraciones y los aspectos técnicos fundamentales de la elaboración de Inventarios Viales y la Categorización de la Red Vial, aplicadas a la realización de estudios de ingeniería de tránsito y transporte. Se exponen los aspectos generales relacionados con la elaboración de los inventarios de infraestructura vial, de señalización y dispositivos de control, de estacionamientos, de paraderos y de rutas de transporte público colectivo urbano de pasajeros, como una herramienta práctica para complementar los procedimientos de campo y optimizar los procesos y análisis de resultados orientados a identificar, caracterizar y cuantificar las variables relacionadas con el desarrollo del fenómeno del tránsito y la actividad del transporte.

Recovery of Pu from PVC vials and bottles used for sample storage

International Nuclear Information System (INIS)

Purohit, Paru; Bhide, M.K.; Kulkarni, M.J.; Kumar, Mithlesh; Adya, V.C.; Hon, N.S.; Kadam, R.M.; Nathaniel, Newton; Natarajan, V.

2011-01-01

Plutonium in the form of oxide is stored in plastic vials and bottles during its analysis for trace metal as say. Due to radiation damage and moisture, small amount of oxide samples were found to be adhering to surface of vials/ bottles. This required methods for safe disposal. Methods involving wet chemical and dry cleaning procedures were evaluated for effective removal of sticking α active plutonium oxide powder from these vials for their safe disposal. Dry cleaning method for removal of plutonium activity was found to be effective method for disposal of storage vial, while wet chemical method was found to be more suitable for removal of plutonium from damaged PVC bottles. (author)

Bioassay guideline 1: general guidlines for bioassay programs

International Nuclear Information System (INIS)

1980-01-01

This guideline is the first of a series of documents which elaborate criteria for bioassay programs, to be presented as recommendations to the Atomic Energy Control Board. It specifies which workers require routine bioassays, the accuracy and frequency of measurements, the dose levels at which specific actions must be taken, and the documentation required

Determination of 226Ra by gamma spectrometry: study of packaging vial of sample for analysis

International Nuclear Information System (INIS)

Carneiro, Andre Cavalcanti

2015-01-01

Determination of radioactivity levels of 226 Ra by gamma spectrometry in a sample is based on measurements of 214 Pb and 214 Bi, daughters of 222 Rn. Because radon is a gas, it can leak from the sample vial or accumulate on the upper empty it. If the vial has any crack, there will be loss of gas, which will cause error in determining the 226 Ra concentration. One possible cause of cracks in the vials, that houses standards and samples, is the radiolysis action in the vial material, usually a polymer. As the demand 226 Ra analysis in different matrices (geological samples, food, plants, etc.) is increasing, it was decided to study some polymer vials available on the market, to verify the feasibility to be used when is applied the analysis method using gamma spectrometry. Four types of polymer vials have been studied. The radiation doses in walls of the vials caused by natural radionuclides present in the sample were simulated using gamma irradiation. Tests, such as compressive strength test and tightness, were applied to the irradiated and non-irradiated vials. First, to verify the effect of radiolysis on the vial material and also if there was 222 Rn diffusion in their walls. These preliminary results pointed out that the acrylic vials are the best option of packaging samples for analysis. This study should be repeated in a larger number of samples for a better evaluation. (author)

Inventarios viales y categorización de la red vial en estudios de Ingeniería de Tránsito y Transporte

Directory of Open Access Journals (Sweden)

Julián Rodrigo Quintero

2011-11-01

Full Text Available Se presentan las principales consideraciones y los aspectos técnicos fundamentales de la elaboración de Inventarios Viales y la Categorización de la Red Vial, aplicadas a la realización de estudios de ingeniería de tránsito y transporte. Se exponen los aspectos generales relacionados con la elaboración de los inventarios de infraestructura vial, de señalización y dispositivos de control, de estacionamientos, de paraderos y de rutas de transporte público colectivo urbano de pasajeros, como una herramienta práctica para complementar los procedimientos de campo y optimizar los procesos y análisis de resultados orientados a identificar, caracterizar y cuantificar las variables relacionadas con el desarrollo del fenómeno del tránsito y la actividad del transporte.

Valoraciones sobre la gestión del sistema de seguridad vial en Cuba.

Directory of Open Access Journals (Sweden)

Tania Ivón Sosa Ibarra

2015-12-01

Full Text Available El presente trabajo tiene como objetivo valorar con enfoque crítico el cumplimiento de la agenda del Observatorio Iberoamericano para la Seguridad Vial (OISEVI que evidencie los aciertos y desaciertos en esta actividad, se analiza en la literatura los enfoques de los autores Tony Bliss y Jeanne Breen que enfatizan en la concepción de sistema no solo a la seguridad vial sino también a la gestión de esta como sistema y se realiza una aplicación de los aspectos de la encuesta del OISEVI a la gestión de la seguridad vial en Cuba por el grupo de asesores de la Comisión Nacional de seguridad vial, pertenecientes a la Universidad de Sancti Spíritus, que durante los últimos años estudian esta problemática, detallando los argumentos que conciben para otorgar los valores en las respuestas al cuestionario. Con esta encuesta se obtiene una primera aproximación del estado de la gestión de la seguridad vial en el país, y se arriban a valoraciones acerca de cómo se encuentra Cuba respecto a los lineamientos básicos y generales que hacen exitosa a la gestión en seguridad vial, basada en los cinco pilares del Plan Mundial para el Decenio de Acción para la Seguridad Vial 2011-2020.

Microbial contamination of single-and multiple-dose vials after opening in a pulmonary teaching hospital

Directory of Open Access Journals (Sweden)

Shadi Baniasadi

Full Text Available OBJECTIVES: Intravenous therapy is a complex procedure usually requiring the preparation of the medication in the clinical area before administration to the patient. Breaches in aseptic technique may result in microbial contaminations of vials which is a potential cause of different avoidable infections. We aimed to investigate the prevalence and pattern of microbial contamination of single- and multiple-dose vials in the largest pulmonary teaching hospital in Iran. METHODS: In a period of 2 months, opened single- and multiple-dose vials from different wards were sampled by a pharmacist. The name of the medication, ward, labeling of the vials, the date of opening, and storing temperature were recorded for each vial. Remained contents of each vial were cultured using appropriate bacterial and fungal growth media. RESULTS: Microbial contamination was identified in 11 of 205 (5.36% of vials. The highest contamination rate was 14.28% for vials used in interventional bronchoscopy unit. The most frequent contaminated medication was insulin. Gram-positive bacteria (81.82% were more significantly involved than gram-negative ones (9.09% and fungi (9.09%, with the highest frequency for Staphylococcus epidermidis . CONCLUSIONS: Our data demonstrate that repeated use of vials especially if basic sterility measures are disobeyed can cause microbial contamination of administered products to the patients. Infection preventionists are responsible to train health care workers regarding aseptic techniques and apply guidelines for aseptic handling of intravenous solutions.

Microbial contamination of single-and multiple-dose vials after opening in a pulmonary teaching hospital

Directory of Open Access Journals (Sweden)

Shadi Baniasadi

2013-02-01

Full Text Available OBJECTIVES: Intravenous therapy is a complex procedure usually requiring the preparation of the medication in the clinical area before administration to the patient. Breaches in aseptic technique may result in microbial contaminations of vials which is a potential cause of different avoidable infections. We aimed to investigate the prevalence and pattern of microbial contamination of single- and multiple-dose vials in the largest pulmonary teaching hospital in Iran. METHODS: In a period of 2 months, opened single- and multiple-dose vials from different wards were sampled by a pharmacist. The name of the medication, ward, labeling of the vials, the date of opening, and storing temperature were recorded for each vial. Remained contents of each vial were cultured using appropriate bacterial and fungal growth media. RESULTS: Microbial contamination was identified in 11 of 205 (5.36% of vials. The highest contamination rate was 14.28% for vials used in interventional bronchoscopy unit. The most frequent contaminated medication was insulin. Gram-positive bacteria (81.82% were more significantly involved than gram-negative ones (9.09% and fungi (9.09%, with the highest frequency for Staphylococcus epidermidis . CONCLUSIONS: Our data demonstrate that repeated use of vials especially if basic sterility measures are disobeyed can cause microbial contamination of administered products to the patients. Infection preventionists are responsible to train health care workers regarding aseptic techniques and apply guidelines for aseptic handling of intravenous solutions.

Measurement of exhalation rate of radon and radon concentration in air using open vial method

International Nuclear Information System (INIS)

Horiuchi, Kimiko; Ishii, Tadashi.

1991-01-01

It was recognized that more than half of total exposure dose on human subject is caused by radon and its decay products which originate from naturally occurring radioactive substances (1988 UNSCEAR). Since then the exhalation of radon from the ground surface has received increasing attention. The authors have developed a new method for the determination of radon in natural water using toluene extraction of radon and applying a liquid scintillation counter of an integral counting technique which is able to get the absolute counting of radon. During these studies, the authors found out that when a counting vial containing of Liquid scintillator (LS)-toluene solution, without a lid, is exposed to the atmosphere for a while, dissolution of radon clearly occurs due to high solubility of radon into toluene layer. To extend this finding for the determination of radon in the atmosphere, the authors devised a new method to actively collect the atmosphere containing radon in a glass bottle by discharging a definite amount of water in it, which is named as open-vial dynamic method. The radon concentration can be easily calculated after the necessary corrections such as the partition coefficient and others. Applying proposed method to measure the radon exhalation rate from the ground surface and radon concentration in air of the dwelling environment, radioactive mineral spring zone and various geological formation such as granitic or sedimentary rocks. (author)

Red Vial de Nicaragua (Optimización y Mantenimiento

Directory of Open Access Journals (Sweden)

Wilfredo Martínez

2013-06-01

Full Text Available La red vial es un patrimonio nacional, el cual es necesario: proteger, conservar, aumentar y mejorar; para apoyar eldesarrollo socioeconómico de nuestro país. La actividad de mantenimiento, constituye un factor determinante quegarantiza la operación satisfactoria del transporte durante la vida útil de los caminos; en sus diferentes modalidades. La ausencia de un mantenimiento preventivo y de un mantenimiento correctivo tardío, conduce a que la inversiónrealizada sufra una depreciación más acelerada, acortando su vida útil; obteniendo un grado de aprovechamientomenor que se traduce en una disminución de los beneficios estimados, ya que la rentabilidad no podrá ser óptima aldescuidar esta función. “Con frecuencia, los costos operativos de los vehículos, excederán los costos de losdepartamentos viales por un factor de 10 o màs, especialmente en carreteras de gran volumen de trànsito”.(Zaniewski, 1989. Por lo tanto, los costos (economía de los usuarios deben ser tomados en cuenta al momento deproyectar la construcción de una carretera. Por tal razón el Gobierno de Nicaragua, en conjunto con lasinstituciones correspondientes, han asumido un rol prioritario en la ejecución y mantenimiento de la red vial. Esteensayo pretende aportar elementos cuantitativos y cualitativos, para el análisis y mejoramiento de la Red Vial.

Residual volume in vials of antibiotics used in pediatrics.

Science.gov (United States)

Chaves, Caroline Magna Pessoa; Bezerra, Carolina Martins; Lima, Francisca Elisângela Teixeira; Cardoso, Maria Vera Lúcia Moreira Leitão; Fonseca, Said Gonçalves da Cruz; Silva, Viviane Martins da

2017-06-12

Quantifying residual volume contained in vials of antibiotics used in pediatrics. This is an experiment involving samples from vials of antibiotics used in a pediatric hospital. Residual volume was identified by calculating the difference in weight measurement before and after the vials were washed. Evaluation of the residual volume difference in the vials was determined by the Wilcoxon non-parametric test for a sample and established at a significance level of 5%. 105 samples of antibiotics were selected. The correct use of the antibiotics oxacillin (88.57%) and ceftriaxone (94.28%) predominated with low residual values. The same did not occur for procaine benzylpenicillin + potassium benzylpenicillin, since a greater residual volume was discarded in 74.28% of the vials. We highlight the need for improvements in managing antibiotics in the institution under study, so that the excess volume of the antibiotics in the vials is used within the acceptable stable time. It is also necessary that the disposal of the residual volume be adequately disposed, since it presents a risk to public health and the environment. Quantificar o volume residual contido em frascos-ampola de antibióticos utilizados na pediatria. Trata-se de um experimento com amostras de frascos-ampola de antibióticos utilizados em hospital pediátrico. O volume residual foi identificado calculando-se a diferença da aferição do peso antes e após a lavagem do frasco-ampola. A avaliação da diferença dos volumes residuais nos frascos-ampola foi determinada pelo teste não paramétrico de Wilcoxon para uma amostra e estabelecido o nível de significância de 5%. Foram selecionadas 105 amostras de antibióticos. Predominou o correto aproveitamento dos antibióticos oxacilina (88,57%) e ceftriaxona (94,28%), com baixos valores residuais. O mesmo não ocorreu com a benzilpenicilina procaína + potássica, pois em 74,28% dos frascos houve descarte de volume residual superior. Destaca-se a necessidade de

Modelo de gestión del tiempo en proyectos viales.

OpenAIRE

Luzuriaga Bojorque, Juan Pablo

2015-01-01

El presente trabajo demuestra la importancia de utilizar un método internacionalmente reconocido para gestionar la terminación de los proyectos viales a tiempo. Tanto entidad contratante como contratistas podrán utilizar las mejores prácticas en gerenciamiento de proyectos para lograr que la construcción de carreteras sean proyectos exitosos. Las entidades contratantes en el Ecuador, evalúan el cumplimiento del cronograma de un proyecto vial, en base de la consecución de un nivel determinado ...

Lack of clinical relevance in routine final subcultures of radiometrically negative BACTEC blood culture vials

International Nuclear Information System (INIS)

Plorde, J.J.; Carlson, L.G.; Dau, M.E.

1982-01-01

During a 38-month period, 10,106 blood specimens were received in the laboratory for culture. These were inoculated into 26,424 vials and processed using the BACTEC radiometric detection system. Of these vials, 1,914 were eventually found to be microbiologically positive. Isolates from 836 vials were judged to be contaminants. In the remaining 1,078 vials, growth was first detected visually or radiometrically in 1,062 and by final subculture in 16. Growth from these sixteen bottles represented 12 clinically significant bacteremic episodes in as many patients. In nine of these episodes, other culture vials from the same patient were positive radiometrically. Therefore, 358 of 361 (99.2%) bacteremic episodes were detected without the benefit of routine final subcultures. The three patients whose bacteremia was missed were diagnosed clinically and placed on appropriate therapy prior to the detection of the bacteremias by final subculture

Physicochemical stability of carfilzomib (Kyprolis®) containing solutions in glass vials, ready-to-administer plastic syringes and infusion bags over a 28-day storage period.

Science.gov (United States)

Kim, Sun Hee; Krämer, Irene

2017-01-01

Centralized aseptic preparation of ready-to-administer carfilzomib containing parenteral solutions in plastic syringes and polyolefine (PO) infusion bags needs profound knowledge about the physicochemical stability in order to determine the beyond-use-date of the preparations. Therefore, the purpose of this study was to determine the physicochemical stability of carfilzomib solution marketed as Kyprolis® powder for solution for infusion. Reconstituted solutions and ready-to-administer preparations of Kyprolis® stored under refrigeration (2-8℃) or at room temperature (25℃) were analyzed at predetermined intervals over a maximum storage period of 28 days. Chemical stability of carfilzomib was planned to be determined with a stability-indicating reversed-phase high-performance liquid chromatography assay. Physicochemical stability was planned to be determined by visual inspection of clarity and color as well as pH measurement. The study results show that reconstituted carfilzomib containing parenteral solutions are stable in glass vials as well as diluted solutions in plastic syringes and PO infusion bags over a period of at least 28 days when stored light protected under refrigeration. When stored at room temperature, reconstituted and diluted carfilzomib solutions are physicochemically stable over 14 days and 10 days, respectively. The physicochemical stability of carfilzomib infusion solutions allows cost-saving pharmacy-based centralized preparation of ready-to-administer preparations.

Complexing Agents and pH Influence on Chemical Durability of Type I Molded Glass Containers.

Science.gov (United States)

Biavati, Alberto; Poncini, Michele; Ferrarini, Arianna; Favaro, Nicola; Scarpa, Martina; Vallotto, Marta

2017-01-01

Among the factors that affect the glass surface chemical durability, pH and complexing agents present in aqueous solution have the main role. Glass surface attack can be also related to the delamination issue causing glass particles' appearance in the pharmaceutical preparation. A few methods to check for glass containers delamination propensity and some control guidelines have been proposed. The present study emphasizes the possible synergy between a few complexing agents with pH on borosilicate glass chemical durability.Hydrolytic attack was performed in small-volume 23 mL type I glass containers autoclaved according to the European Pharmacopoeia or United States Pharmacopeia for 1 h at 121 °C, in order to enhance the chemical attack due to time, temperature, and the unfavorable surface/volume ratio. Solutions of 0.048 M or 0.024 M (M/L) of the acids citric, glutaric, acetic, EDTA (ethylenediaminetetraacetic acid), together with sodium phosphate with water for comparison, were used for the trials. The pH was adjusted ±0.05 units at fixed values 5.5, 6.6, 7, 7.4, 8, and 9 by LiOH diluted solution.Because silicon is the main glass network former, silicon release into the attack solutions was chosen as the main index of the glass surface attack and analysed by inductively coupled plasma atomic emission spectrophotometry. The work was completed by the analysis of the silicon release in the worst attack conditions of molded glass, soda lime type II glass, and tubing borosilicate glass vials to compare different glass compositions and forming technologies. Surface analysis by scanning electron microscopy was finally performed to check for the surface status after the worst chemical attack condition by citric acid. LAY ABSTRACT: Glass, like every packaging material, can have some usage limits, mainly in basic pH solutions. The issue of glass surface degradation particles that appear in vials (delamination) has forced a number of drug product recalls in recent years

Cluster endophthalmitis following multiple intravitreal bevacizumab injections from a single use vial

Directory of Open Access Journals (Sweden)

Perwez Khan

2016-01-01

Full Text Available The risk of endophthalmitis is always a concern when an intraocular procedure is performed. Intravitreal injection is a frequently used method for therapeutic management of many diseases, affecting the posterior segment of the eye. Hence, it is important to assess the risk of complications, especially endophthalmitis. Most studies conducted concentrate on risk assessment from single use from single drug vial. The present article reports the occurrence of cluster endophthalmitis following multiple intravitreal bevacizumab injections from a single vial. Intravitreal injection of bevacizumab was administered to eight eyes of eight patients. Administered dose was prepared from single 4-ml vial of bevacizumab and was injected in the eye, after patient preparation and under aseptic conditions. The procedure was repeated for the remaining patients, thereby imparting multiple pricks in the same vial. Four of the eight patients reported to the hospital on the 3rd day after injection with complaints of pain, watering, and diminution of vision. Two patients reported the following day with similar complaints. Two patients who did not report by the 4th day were contacted and recalled for an examination. All the patients were thoroughly examined using slit lamp biomicroscopy and indirect ophthalmoscopy. Six out of eight were clinically diagnosed to have endophthalmitis and were administered intravitreal antibiotics. The present report highlights possibility of microbial contamination of the drug vial or during compounding process. However, from the present incident, we are encouraged to stay vigilant and wary of contamination

Stability of the intra- and extracellular toxins of Prymnesium parvum using a microalgal bioassay

DEFF Research Database (Denmark)

Blossom, Hannah Eva; Andersen, Nikolaj Gedsted; Rasmussen, Silas Anselm

2014-01-01

easily maintained. Reducing oxidation by storing the supernatant with no headspace in the vials significantly slowed loss of activity when stored at 4°C. We show that the lytic activity of the intracellular toxins, when released by sonication, is not as high as the extracellular toxins, however...... of P. parvum toxins before attempting to isolate and characterize them. The extracellular toxin in the supernatant is highly unstable, and it loses significant lytic effects after 3 days despite storage at −20°C and after only 24h stored at 4°C. However, when stored at −80°C, lytic activity is more...... the stability of the intracellular toxins when kept as a cell pellet at −20°C is excellent, which proves this is a sufficient storage method for less than 3 months. Our results provide an ecologically appropriate algal bioassay to quantify lytic activity of P. parvum toxins and we have advanced our knowledge...

Determination of the external contamination and cross-contamination by cytotoxic drugs on the surfaces of vials available on the Swiss market.

Science.gov (United States)

Fleury-Souverain, Sandrine; Nussbaumer, Susanne; Mattiuzzo, Marc; Bonnabry, Pascal

2014-04-01

The external contamination and cross-contamination by cytotoxic drugs on the surface (outside and septum) of 133 vials from various manufacturers and available on the Swiss market were evaluated. All of the tested vials contained one of the following active ingredients: cyclophosphamide, cytarabine, doxorubicin, epirubicin, etoposide phosphate, gemcitabine, ifosfamide, irinotecan, methotrexate or vincristine. The validated wiping liquid chromatography-mass spectrometry method used in this study allowed for the simultaneous determination of these 10 cytotoxic drugs in less than 30 min. External contamination by cytotoxic drugs was detected on 63% of tested vials (outside and septum). The highest contamination level was observed on etoposide phosphate vials with 1896.66 ng of active ingredient on the outside of the vial. Approximately 20% of the contaminated vials had greater than 10 ng of cytotoxic drugs. Chemical contamination on the septum was detected on 38% of the vials. No contamination or very low levels of cytotoxic drugs, less than 1 ng per vial, were detected on the vials protected by plastic shrink-wrap. Traces of cytotoxic drugs different from the active ingredient were detected on 35% of the tested vials. Handling cytotoxic vials with gloves and having a procedure for the decontamination of vials are of the utmost importance for reducing exposure to cytotoxic drugs. Moreover, manufacturers must improve their procedures to provide products free from any contamination.

Comparison of PCE and TCE disappearance in heated volatile organic analysis vials and flame-sealed ampules.

Science.gov (United States)

Costanza, Jed; Pennell, Kurt D

2008-02-01

The rates of hydrolysis reported for tetrachloroethylene (PCE) and trichloroethylene (TCE) at elevated temperatures range over two orders-of-magnitude, where some of the variability may be due to the presence of a gas phase. Recent studies suggest that volatile organic analysis (VOA) vials provide a low-cost and readily available zero headspace system for measuring aqueous-phase hydrolysis rates. This work involved measuring rates of PCE and TCE disappearance and the corresponding appearance of dechlorination products in water-filled VOA vials and flame-sealed ampules incubated at 21 and 55 degrees C for up to 95.5 days. While PCE and TCE concentrations readily decreased in the VOA vials to yield first-order half lives of 11.2 days for PCE and 21.1 days for TCE at 55 degrees C, concentrations of anticipated dechlorination products, including chloride, remained constant or were not detected. The rate of PCE disappearance was 34 times faster in VOA vials at 55 degrees C compared to values obtained with flame-sealed ampules containing PCE-contaminated water. In addition, the concentration of TCE increased slightly in flame-sealed ampules incubated at 55 degrees C, while a decrease in TCE levels was observed in the VOA vials. The observed losses of PCE and TCE in the VOA vials were attributed to diffusion and sorption in the septa, rather than to dechlorination. These findings demonstrate that VOA vials are not suitable for measuring rates of volatile organic compound hydrolysis at elevated temperatures.

Rapid bioassay for oil-contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Ashworth, J. [ALS Environmental, Edmonton, AB (Canada); Oosterbroek, L. [HydroQual, Calgary, AB (Canada)

2010-07-01

This PowerPoint presentation described a study conducted to develop a rapid bioassay for soils contaminated with oil. The bioassay method was designed for a weight of evidence (WoE) approach and eco-contact guideline derivation protocol. Microtox bioassays were conducted on cyclodextrin extracts of soil quantified by solvent extraction and gas chromatography. The method was demonstrated using straight {beta}-cyclodextrin soil extracts and activated {beta}-cyclodextrin soil extracts. An analysis of the methods showed that the activation step weakens or breaks the cyclodextrin and polycyclic hydrocarbon (PHC) inclusion complex. The released PHC became toxic to the microtox organism. Results from the bioassays were then correlated with earthworm reproduction bioassay results. tabs., figs.

Calibration of the NPL secondary standard radionuclide calibrator for the new 10R Schott, Type 1+ vials

International Nuclear Information System (INIS)

Baker, M.

2005-01-01

For many years, P6 vials have been used for the distribution of a wide range of diagnostic and therapeutic radioactive solutions. The activity measurements were performed in this geometry and, in time, the UK calibration system for nuclear medicine was based on this container as a standard. However, one major supplier of radiopharmaceuticals has replaced the P6 vial with the 10R Type 1+ Schott vial. As the dimensions of the new vial are different from those of the P6 vial and the responses of radionuclide calibrators are known to be container dependent, the need for re-calibration became apparent. Preliminary measurements made on some typical radionuclide calibrators for 125 I solution indicated a difference in response of about 10% between the two vials. The master ionisation chamber of the NPL secondary standard radionuclide calibrator has been re-calibrated and new calibration factors and volume correction factors for 10R Schott vials have been derived for the relevant medical radionuclides. The standard holder was also modified to accommodate the new larger vial. The complete list of factors and the method used to determine them is presented in this paper. The availability of these new factors will improve the quality of activity measurements in nuclear medicine, as calibration services can now be provided by NPL for the new container. These factors can also be employed for all commercial NPL secondary standard radionuclide calibrators (now known as the NPL-CRC and previously as the 671 or ISOCAL IV)

The measurement of activity in vials and syringes using a radionuclide assay calibrator

International Nuclear Information System (INIS)

Hooper, S.A.; Davies, I.H.

1993-01-01

To enable accurate measurements of the activity in both vials and syringes, a series of measurements was undertaken to ascertain the changes in response with geometry in nine isotope assay calibrators. From these measurements, two jigs were made for each calibrator to enable (a) optimal measurement of activity in vials and (b) optimal measurement of activity in a variety of syringe sizes. (Author)

Experiencia-modelo piloto de los talleres de seguridad vial, como alternativa a la pena privativa de libertad en los delitos contra la seguridad vial

Directory of Open Access Journals (Sweden)

Isabel Germán Mancebo

2012-12-01

Full Text Available Algunos de los delitos contra la seguridad vial en España tienen asignada la pena de trabajos en beneficio de la comunidad (TBC. Y en la práctica se han percibido problemas en su implementación, entre otros motivos por el aumento de la comisión de los delitos de tránsito y la escasez de puestos de trabajo social para poder llevar a cabo los trabajos comunitarios. Tanto la reciente modificación del Código Penal, como de la normativa reguladora de esta sanción, permite desarrollar los TBC por medio de la realización de talleres. En este artículo se presenta la experiencia-modelo piloto de los talleres de seguridad vial que dan contenido a la pena de TBC, como alternativa a la pena privativa de libertad, lo que resulta de especial interés al ser una de las primeras experiencias de esta naturaleza en España. Para ello se describen los talleres desarrollados, mensualmente, durante el año 2010, a saber: su primer año de funcionamiento en la provincia de Gipuzkoa (España, detallando su estructura, dinámica y tareas -tanto formativas como de utilidad pública- que realizaron los penados. La implementación de estos talleres ha paliado las deficiencias percibidas en la aplicación de la pena de TBC, dotándola de contenido, y superando así las críticas a las que esta sanción se había visto expuesta. Los talleres de seguridad vial responden de forma efectiva al papel preventivo que se le ha otorgado a este tipo de sanciones en el ámbito de la seguridad vial.

An application for impedance spectroscopy in the characterisation of the glass transition during the lyophilization cycle: the example of a 10% w/v maltodextrin solution.

Science.gov (United States)

Smith, Geoff; Arshad, Muhammad Sohail; Polygalov, Eugene; Ermolina, Irina

2013-11-01

Impedance spectroscopy has been used for the measurement of the glass transition of a 10 % maltodextrin solution contained within a glass vial, with externally attached electrodes. Features of the pseudo-relaxation process, associated with the composite impedance of the glass vial-solution assembly, were characterised by the peak amplitude, C(peak)(″), and peak frequency, f(peak), of the capacitance spectra and the equivalent circuit elements that model the impedance spectra (i.e. the solution resistance and solution capacitance) and monitored every 3 min during re-heating of the solution. The time derivatives of all four parameters studied provided a glass transition in close agreement with DSC measurements (-17 °C) and at a precision of ± 0.5 °C. The temperature dependencies of the solution resistance and peak frequency were then characterised with the Arrhenius and Vogel-Fulcher-Tammann fit functions, at temperatures below and above Tg, respectively. The energy of activation (below Tg) was estimated at ~20 kJ mol(-1), and the fragility index (If) of the glass forming liquid (above Tg) was estimated at 0.9. The significance of the fragility index to the development, optimisation and control of the freeze-drying cycle is highlighted. Copyright © 2013 Elsevier B.V. All rights reserved.

Isolation of HIV-1 from experimentally contaminated multidose local anaesthetic vials.

Science.gov (United States)

Druce, J D; Locarnini, S A; Birch, C J

1995-05-15

To investigate the hypothesis that HIV can be transmitted via contamination of multidose vials of local anaesthetic solution through reuse of needles and syringes. Laboratory study. (1) By experiments with multidose vials and disposable needles and syringes, we identified a sequence of events in which HIV could contaminate the anaesthetic solution. (2) Three anaesthetic solutions were contaminated with a laboratory strain of HIV and tested by viral culture and p24 enzyme immunoassay one, two and four hours later to see how long the virus remained active. (1) Needles and syringes retained small volumes of fluid after use (mean, 25 microL; in syringe alone, mean 16 microL) which could be transferred to multidose vials of local anaesthetic. (2) 10 mL of anaesthetic solution contaminated with 8 microL of HIV-infected solution (equivalent to 1% infected lymphocytes in vivo) contained active virus one hour later. In some settings, HIV could be isolated four hours after exposure. When inadvertently contaminated with HIV, multidose solutions represent a potential source of transmissible virus.

Characteristics of high-purity Teflon vial for 14C measurement in old tree rings

International Nuclear Information System (INIS)

Sakurai, H.; Saswaki, Y.; Matsumoto, T.; Aoki, T.; Kato, W.; Gandou, T.; Gunji, S.; Tokanai, F.

2003-01-01

14 C concentration in single-year tree rings of an old cedar of ca. 2500 years ago is measured to investigate the 11-yr periodicity of solar activity. Our highly accurate 14 C measuring system is composed of a benzene synthesizer capable of producing a large quantity (10 g) of benzene and a Quantulus 1220 TM liquid scintillation counting system. The accuracy is less than 0.2% for measurements of 14 C concentration. The benzene sample is contained in a high-purity Teflon/copper-counting vial (20 ml) manufactured by Wallac Oy Company. We found a vial with an irregular copper cap for the measurements of 11 tree rings. The behavior of the vial with the irregular cap was investigated. The Teflon sheet inside the cap plays an important role in achieving stable measurement. The rate of volatilization of the benzene was less than 0.35 mg/day for vials with ordinary caps. This results in the volatilization rate of 0.003% for 10.5 g of benzene and hence guarantees measurement at an accuracy of 0.2% for 70 days

Comparison of vials and prefilled pens of a rapid-acting insulin analog on pharmacy budgets in a long-term care setting.

Science.gov (United States)

Eby, Elizabeth L; Smolen, Lee J; Pitts, Amber C; Krueger, Linda A; Andrews, Jeffrey Scott

2014-12-01

Estimate budgetary impact for skilled nursing facility converting from individual patient supply (IPS) delivery of rapid-acting insulin analog (RAIA) 10-mL vials or 3-mL prefilled pens to 3-mL vials. A budget-impact model used insulin volume purchased and assumptions of length of stay (LOS), daily RAIA dose, and delivery protocol to estimate the cost impact of using 3-mL vials. Skilled nursing facility. Medicare Part A patients. Simulations conducted using 12-month current and future scenarios. Comparisons of RAIA use for 13- and 28-day LOS. RAIA costs and savings, waste reduction. For patients with 13-day LOS using 20 units/day of IPS insulin, the model estimated a 70% reduction in RAIA costs and units purchased and a 95% waste reduction for the 3-mL vial compared with the 10-mL vial. The estimated costs for prefilled pen use were 58% lower than for use of 10-mL vials. The incremental savings associated with 3-mL vial use instead of prefilled pens was 28%, attributable to differences in per-unit cost of insulin in vials versus prefilled pens. Using a more conservative scenario of 28-day LOS at 20 units/day, the model estimated a 40% reduction in RAIA costs and units purchased, resulting in a 91% reduction in RAIA waste for the 3-mL vial, compared with 10-mL vial. Budget-impact analysis of conversion from RAIA 10-mL vials or 3-mL prefilled pens to 3-mL vials estimated reductions in both insulin costs and waste across multiple scenarios of varying LOS and patient daily doses for skilled nursing facility stays.

Bioassay Laboratory

Data.gov (United States)

Federal Laboratory Consortium — The Bioassay Laboratory is an accredited laboratory capable of conducting standardized and innovative environmental testing in the area of aquatic ecotoxicology. The...

A critical assessment of the occurrence and extend of oxygen contamination during anaerobic incubations utilizing commercially available vials

DEFF Research Database (Denmark)

De Brabandere, Loreto; Thamdrup, Bo; Revsbech, Niels Peter

2011-01-01

contaminate the samples by oxygen diffusing from or through their plastic or rubber components. In this study, we investigated the sources and extent of oxygen contamination during anoxic incubations, and present solutions to minimize oxygen contamination. In particular, we investigated oxygen contamination...... in Labco® Exetainers, glass vials with a butyl rubber septum in the screw cap, which are frequently used in microbiological experiments. Our results show that significant oxygen contamination occurred at different stages during the incubation. Contamination occurred when Exetainers were either filled...... or incubated for more than16 h under oxic atmosphere, but also under an oxygen-free atmosphere due to diffusion of oxygen out of the butyl rubber septum. Therefore, to avoid oxygen contamination during incubations, we suggest (1) filling and incubating the incubation containers under anoxic atmosphere (glove...

77 FR 14837 - Bioassay at Uranium Mills

Science.gov (United States)

2012-03-13

... NUCLEAR REGULATORY COMMISSION [NRC-2012-0057] Bioassay at Uranium Mills AGENCY: Nuclear Regulatory..., ``Bioassay at Uranium Mills.'' This guide describes a bioassay program acceptable to the NRC staff for uranium mills and applicable portions of uranium conversion facilities where the possibility of exposure...

Sample vial inserts: A better approach for sampling heterogeneous slurry samples in the SRS Defense Waste Processing Facility

International Nuclear Information System (INIS)

Coleman, C.J.; Goode, S.R.

1996-01-01

A convenient and effective new approach for analyzing DWPF samples involves the use of inserts with volumes of 1.5--3 ml placed in the neck of 14 ml sample vials. The inserts have rims that conform to the rim of the vials so that they sit straight and stable in the vial. The DWPF tank sampling system fills the pre-weighed insert rather than the entire vial, so the vial functions only as the insert holder. The shielded cell operator then removes the vial cap and decants the insert containing the sample into a plastic bottle, crucible, etc., for analysis. Inert materials such as Teflon, plastic, and zirconium are used for the insert so it is unnecessary to separate the insert from the sample for most analyses. The key technique advantage of using inserts to take DWPF samples versus filling sample vials is that it provides a convenient and almost foolproof way of obtaining and handling small volumes of slurry samples in a shielded cell without corrupting the sample. Since the insert allows the entire sample to be analyzed, this approach eliminates the errors inherent with subsampling heterogeneous slurries that comprise DWPF samples. Slurry samples can then be analyzed with confidence. Analysis times are dramatically reduced by eliminating the drying and vitrification steps normally used to produce a homogeneous solid sample. Direct dissolution and elemental analysis of slurry samples are achieved in 8 hours or less compared with 40 hours for analysis of vitrified slurry samples. Comparison of samples taken in inserts versus full vials indicate that the insert does not significantly affect sample composition

Seguridad Vial y Procesos Psicológicos: Acciones Preventivas. [ Road Safety and Psychological Processes: Preventive Actions

OpenAIRE

Manuel Ernesto Riaño Garzón; Nathalie Claire Raynaud Prado; Edgar Alexis Diaz Camargo

2017-01-01

El artículo revisa la relación entre los procesos psicológicos y la seguridad vial desde una postura preventiva con el fin de proporcionar evidencias sobre alternativas utilizadas en terapia que puedan ser de utilidad para el adecuado funcionamiento psico-fisiológico y que determinen una mayor Seguridad Vial. Dicha revisión resulta pertinente en el marco de la Policía Nacional y de la Seguridad Vial en tanto ilustra metodologías empíricamente validadas que pueden ser utilizadas por las person...

Plasmonically amplified fluorescence bioassay with microarray format

Science.gov (United States)

Gogalic, S.; Hageneder, S.; Ctortecka, C.; Bauch, M.; Khan, I.; Preininger, Claudia; Sauer, U.; Dostalek, J.

2015-05-01

Plasmonic amplification of fluorescence signal in bioassays with microarray detection format is reported. A crossed relief diffraction grating was designed to couple an excitation laser beam to surface plasmons at the wavelength overlapping with the absorption and emission bands of fluorophore Dy647 that was used as a label. The surface of periodically corrugated sensor chip was coated with surface plasmon-supporting gold layer and a thin SU8 polymer film carrying epoxy groups. These groups were employed for the covalent immobilization of capture antibodies at arrays of spots. The plasmonic amplification of fluorescence signal on the developed microarray chip was tested by using interleukin 8 sandwich immunoassay. The readout was performed ex situ after drying the chip by using a commercial scanner with high numerical aperture collecting lens. Obtained results reveal the enhancement of fluorescence signal by a factor of 5 when compared to a regular glass chip.

Bioassay criteria for environmental restoration workers

International Nuclear Information System (INIS)

Carbaugh, E.H.; Bihl, D.E.

1993-01-01

Environmental restoration (ER) work at the U. S. Department of Energy Hanford Site posed questions concerning when to perform bioassay monitoring of workers for potential intakes of radioactivity. Application of criteria originally developed for use inside radionuclide processing facilities to ER work resulted in overly restrictive bioassay requirements. ER work typically involves site characterization or, excavating large quantities of potentially contaminated soil, rather than working with concentrated quantities of radioactivity as in a processing facility. An improved approach, tailored to ER work, provided soil contamination concentrations above which worker bioassay would be required. Soil concentrations were derived assuming acute or chronic intakes of 2% of an Annual Limit on Intake (ALI), or a potential committed effective dose equivalent of 100 mrem, and conservative dust loading of air from the work. When planning ER work, the anticipated soil concentration and corresponding need for bioassay could be estimated from work-site historical records. Once site work commenced, soil sampling and work-place surveys could be used to determine bioassay needs. This approach substantially reduced the required number of bioassay samples with corresponding reductions in analytical costs, schedules, and more flexible work-force management. (Work supported by the US Department of Energy under contract DOE-AC06-76RLO 1830.)

Fractionation of nitrogen-15 during distillation of ammonia in an all-glass still

International Nuclear Information System (INIS)

O'Deen, W.A.; Porter, L.K.

1980-01-01

The detection of N isotopic fractionation during distillation in an all-glass Kjeldahl distillation apparatus is reported. Five milligrams of N from (NH 4 ) 2 SO 4 in 100 ml of solution at a 1.3 atom % 15 N level were distilled from a 250 ml boiling flask through a Kontes Kjeldahl distillation apparatus. The solution was made basic with 1 ml of 13N NaOH and distillate was collected sequentially in three glass shell vials, and then in a 100 ml beaker, each containing .5ml of 1N HCl. Three ml of distillate were collected in each vial and 40 ml in the beaker. The first distilled N-fraction was lower in atom % 15 N than the standard. In subsequent fractions, atom % 15 N values increased until the last fraction was higher than the undistilled standard. The last fraction differed from the first fraction and standard significantly at the 0.01 level. The first fraction differed significantly from the standard at the 0.05 probability level by 3.2 parts per thousand. Data indicated that atom % 15 N distillation values can be expected to be slightly lower than undistilled values owing to N isotopic fractionation. 1 table

Bioassay programs for radiation protection

International Nuclear Information System (INIS)

1979-01-01

This report discusses the rationale for the establishment of bioassay programs as a means of protection for radiation workers in the nuclear industry. The bioassay program of the Radiation Protection Bureau is described for the years 1966-1978 and plans for future changes are outlined. (auth)

78 FR 14095 - Determination That GEREF (Sermorelin Acetate) Injection, 0.5 Milligrams Base/Vial and 1.0...

Science.gov (United States)

2013-03-04

...] Determination That GEREF (Sermorelin Acetate) Injection, 0.5 Milligrams Base/Vial and 1.0 Milligrams Base/Vial, and GEREF (Sermorelin Acetate) Injection, 0.05 Milligrams Base/Amp, Were Not Withdrawn From Sale for...

Proteja a sus seres queridos de las lesiones viales

Centers for Disease Control (CDC) Podcasts

Este podcast, que forma parte de la iniciativa Proteja a sus seres queridos, aborda las medidas que pueden tomar los padres de familia para ayudar a proteger a sus niños de las lesiones viales, una de las principales causas de lesiones infantiles.

Determination of the influence factors of the radiopharmaceutical vials dimensions used for activimeter calibration at IPEN

International Nuclear Information System (INIS)

Martins, E.W.; Potiens, M.P.A.

2012-01-01

This paper presents the establishment of a quality control program and correction factors for the geometry of the vials used for distribution of radiopharmaceutical and activimeters calibration. The radiopharmaceutical produced by IPEN 67 Ga, 131 I, 201 Tl and 99m Tc had been tested using two different vials. Results show a maximum variation of 22% for 201 Tl, and the minimum variation was 2.98% for 131 I. The correction factors must be incorporated in the routine calibration of the activimeters. - Highlights: ► Establishement of quality control program for reference activimeters. ► Determination of correction factors for the geometry of vials. ► Radiopharmaceuticals tested for different vials were 67 Ga, 131 I, 201 Tl and 99m Tc. ► The maximum variation was 22% for 201 Tl and the minimum variation was 2.98% for 131 I. ► Correction factors must be incorporated in the calibration of the activimeters.

Impact of changing the measles vaccine vial size on Niger's vaccine supply chain: a computational model

Directory of Open Access Journals (Sweden)

Kenea Hailu

2011-06-01

Full Text Available Abstract Background Many countries, such as Niger, are considering changing their vaccine vial size presentation and may want to evaluate the subsequent impact on their supply chains, the series of steps required to get vaccines from their manufacturers to patients. The measles vaccine is particularly important in Niger, a country prone to measles outbreaks. Methods We developed a detailed discrete event simulation model of the vaccine supply chain representing every vaccine, storage location, refrigerator, freezer, and transport device (e.g., cold trucks, 4 × 4 trucks, and vaccine carriers in the Niger Expanded Programme on Immunization (EPI. Experiments simulated the impact of replacing the 10-dose measles vial size with 5-dose, 2-dose and 1-dose vial sizes. Results Switching from the 10-dose to the 5-dose, 2-dose and 1-dose vial sizes decreased the average availability of EPI vaccines for arriving patients from 83% to 82%, 81% and 78%, respectively for a 100% target population size. The switches also changed transport vehicle's utilization from a mean of 58% (range: 4-164% to means of 59% (range: 4-164%, 62% (range: 4-175%, and 67% (range: 5-192%, respectively, between the regional and district stores, and from a mean of 160% (range: 83-300% to means of 161% (range: 82-322%, 175% (range: 78-344%, and 198% (range: 88-402%, respectively, between the district to integrated health centres (IHC. The switch also changed district level storage utilization from a mean of 65% to means of 64%, 66% and 68% (range for all scenarios: 3-100%. Finally, accounting for vaccine administration, wastage, and disposal, replacing the 10-dose vial with the 5 or 1-dose vials would increase the cost per immunized patient from $0.47US to $0.71US and $1.26US, respectively. Conclusions The switch from the 10-dose measles vaccines to smaller vial sizes could overwhelm the capacities of many storage facilities and transport vehicles as well as increase the cost per

Impact of changing the measles vaccine vial size on Niger's vaccine supply chain: a computational model.

Science.gov (United States)

Assi, Tina-Marie; Brown, Shawn T; Djibo, Ali; Norman, Bryan A; Rajgopal, Jayant; Welling, Joel S; Chen, Sheng-I; Bailey, Rachel R; Kone, Souleymane; Kenea, Hailu; Connor, Diana L; Wateska, Angela R; Jana, Anirban; Wisniewski, Stephen R; Van Panhuis, Willem G; Burke, Donald S; Lee, Bruce Y

2011-06-02

Many countries, such as Niger, are considering changing their vaccine vial size presentation and may want to evaluate the subsequent impact on their supply chains, the series of steps required to get vaccines from their manufacturers to patients. The measles vaccine is particularly important in Niger, a country prone to measles outbreaks. We developed a detailed discrete event simulation model of the vaccine supply chain representing every vaccine, storage location, refrigerator, freezer, and transport device (e.g., cold trucks, 4 × 4 trucks, and vaccine carriers) in the Niger Expanded Programme on Immunization (EPI). Experiments simulated the impact of replacing the 10-dose measles vial size with 5-dose, 2-dose and 1-dose vial sizes. Switching from the 10-dose to the 5-dose, 2-dose and 1-dose vial sizes decreased the average availability of EPI vaccines for arriving patients from 83% to 82%, 81% and 78%, respectively for a 100% target population size. The switches also changed transport vehicle's utilization from a mean of 58% (range: 4-164%) to means of 59% (range: 4-164%), 62% (range: 4-175%), and 67% (range: 5-192%), respectively, between the regional and district stores, and from a mean of 160% (range: 83-300%) to means of 161% (range: 82-322%), 175% (range: 78-344%), and 198% (range: 88-402%), respectively, between the district to integrated health centres (IHC). The switch also changed district level storage utilization from a mean of 65% to means of 64%, 66% and 68% (range for all scenarios: 3-100%). Finally, accounting for vaccine administration, wastage, and disposal, replacing the 10-dose vial with the 5 or 1-dose vials would increase the cost per immunized patient from $0.47US to $0.71US and $1.26US, respectively. The switch from the 10-dose measles vaccines to smaller vial sizes could overwhelm the capacities of many storage facilities and transport vehicles as well as increase the cost per vaccinated child.

Laser Scanner Como Sistema de Detección de Entornos Viales

Directory of Open Access Journals (Sweden)

F. García

2011-01-01

Full Text Available Resumen: Los últimos avances en seguridad vial, con sistemas cada vez más complejos, requieren de los más modernos sistemas de adquisición de información. La naturaleza misma del problema requiere sensores capaces de proveer información fiable para tareas complejas y exigentes. Los escáneres láser (LIDAR han demostrado ser una familia de sensores altamente fiable, por lo que durante los últimos años los esfuerzos dedicados a investigar posibles aplicaciones viales han ido en aumento. De esta forma, es cada vez más frecuente observar sistemas de ayuda a la conducción (ADAS con este tipo de dispositivos que proveen de información del entorno necesaria para realizar tareas complejas como deteccián y prediccián de situaciones peligrosas. En el presente trabajo, dos sistemas LIDAR han sido probados para comprobar sus capacidades reales en entornos viales. En segundo término, se propone una aplicación que hace uso de las capacidades de dichos sensores para la detección y clasificación de obstaculos en entornos viarios. Palabras clave: sensores, procesamiento de senales, sistemas reales, vehiculos, algoritmos de deteccion

Bioassay guideline 2: guidelines for tritium bioassay

International Nuclear Information System (INIS)

1983-01-01

This guideline is one of a series under preparation by the Federal-Provincial Working Group on Bioassay and In Vivo Monitoring Criteria. In this report tritium compounds have been grouped into four categories for the purpose of calculating Annual Limits on Intake and Investigation Levels: tritium gas, tritiated water, tritium-labelled compounds and nucleic acid precursors

Bioassay method for Uranium in urine by Delay Neutron counting; Metoda Bioassay Uranium dalam urin dengan pencacahan Netron Kasip

Energy Technology Data Exchange (ETDEWEB)

Suratman,; Purwanto,; Sukarman-Aminjoyo, [Yogyakarta Nuclear Research Centre, National Atomic Energy Agency, Yogyakarta (Indonesia)

1996-04-15

A bioassay method for uranium in urine by neutron counting has been studied. The aim of this research is to obtain a bioassay method for uranium in urine which is used for the determination of internal dose of radiation workers. The bioassay was applied to the artificially uranium contaminated urine. The weight of the contaminant was varied. The uranium in the urine was irradiated in the Kartini reactor core, through pneumatic system. The delayed neutron was counted by BF3 neutron counter. Recovery of the bioassay was between 69.8-88.8 %, standard deviation was less than 10 % and the minimum detection was 0.387 {mu}g.

Determination of the influence factors of the radiopharmaceutical vials dimensions used for activimeter calibration at IPEN

Energy Technology Data Exchange (ETDEWEB)

Martins, E.W. [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN), Avenida Professor Lineu Prestes, 2242, 05508-000 Sao Paulo, SP (Brazil); Potiens, M.P.A., E-mail: mppalbu@ipen.br [Instituto de Pesquisas Energeticas e Nucleares (IPEN-CNEN), Avenida Professor Lineu Prestes, 2242, 05508-000 Sao Paulo, SP (Brazil)

2012-07-15

This paper presents the establishment of a quality control program and correction factors for the geometry of the vials used for distribution of radiopharmaceutical and activimeters calibration. The radiopharmaceutical produced by IPEN {sup 67}Ga, {sup 131}I, {sup 201}Tl and {sup 99m}Tc had been tested using two different vials. Results show a maximum variation of 22% for {sup 201}Tl, and the minimum variation was 2.98% for {sup 131}I. The correction factors must be incorporated in the routine calibration of the activimeters. - Highlights: Black-Right-Pointing-Pointer Establishement of quality control program for reference activimeters. Black-Right-Pointing-Pointer Determination of correction factors for the geometry of vials. Black-Right-Pointing-Pointer Radiopharmaceuticals tested for different vials were {sup 67}Ga, {sup 131}I, {sup 201}Tl and {sup 99m}Tc. Black-Right-Pointing-Pointer The maximum variation was 22% for {sup 201}Tl and the minimum variation was 2.98% for {sup 131}I. Black-Right-Pointing-Pointer Correction factors must be incorporated in the calibration of the activimeters.

Experimental studies on absorbed dose in radiation sterilization of pharmaceutical preparation

International Nuclear Information System (INIS)

Ohnishi, Tokuhiro; Okamoto, Shinichi; Kimura, Syojiro; Taimatsu, Meiko.

1991-01-01

For radiation sterilization, it is necessary to decide the irradiation conditions considering a balance between sterilization efficiency and chemical changes of samples by irradiation. These effects may be estimated by the product of two factors (D 10 and G value) and absorbed dose. In this work, it has been found experimentally by using Fricke dosimeter that the absorbed doses of the samples in vessels different in size, material, volume, etc. are not equal under the same gamma-ray irradiation condition. The correction factor from exposure to absorbed dose was estimated to be 6-7% for organic vessels (a polyethylene bag and a polystyrene vial) and a 20-ml glass vial, 9% for a 10-ml glass vial, and 10% for the 5-ml glass vial. These values of the correction factor were confirmed by using the changes of enzymic activity of saccharated powder pepsin preparation. In the cases of using organic vessels and the 10-ml glass vial, G-values for the change of the enzymic activity were calculated to show similar values in the range from 0.79 to 0.82. However, in the case of a small glass vial (5-ml), the value was 0.93. (author)

Circular Bioassay Platforms for Applications in Microwave-Accelerated Techniques.

Science.gov (United States)

Mohammed, Muzaffer; Clement, Travis C; Aslan, Kadir

2014-12-02

In this paper, we present the design of four different circular bioassay platforms, which are suitable for homogeneous microwave heating, using theoretical calculations (i.e., COMSOL™ multiphysics software). Circular bioassay platforms are constructed from poly(methyl methacrylate) (PMMA) for optical transparency between 400-800 nm, has multiple sample capacity (12, 16, 19 and 21 wells) and modified with silver nanoparticle films (SNFs) to be used in microwave-accelerated bioassays (MABs). In addition, a small monomode microwave cavity, which can be operated with an external microwave generator (100 W), for use with the bioassay platforms in MABs is also developed. Our design parameters for the circular bioassay platforms and monomode microwave cavity during microwave heating were: (i) temperature profiles, (ii) electric field distributions, (iii) location of the circular bioassay platforms inside the microwave cavity, and (iv) design and number of wells on the circular bioassay platforms. We have also carried out additional simulations to assess the use of circular bioassay platforms in a conventional kitchen microwave oven (e.g., 900 W). Our results show that the location of the circular bioassay platforms in the microwave cavity was predicted to have a significant effect on the homogeneous heating of these platforms. The 21-well circular bioassay platform design in our monomode microwave cavity was predicted to offer a homogeneous heating pattern, where inter-well temperature was observed to be in between 23.72-24.13°C and intra-well temperature difference was less than 0.21°C for 60 seconds of microwave heating, which was also verified experimentally.

APIC position paper: Safe injection, infusion, and medication vial practices in health care.

Science.gov (United States)

Dolan, Susan A; Arias, Kathleen Meehan; Felizardo, Gwen; Barnes, Sue; Kraska, Susan; Patrick, Marcia; Bumsted, Amelia

2016-07-01

The transmission of bloodborne viruses and other microbial pathogens to patients during routine health care procedures continues to occur because of the use of improper injection, infusion, medication vial, and point-of-care testing practices by health care personnel. These unsafe practices occur in various clinical settings and result in unacceptable and devastating events for patients. This document updates the Association for Professionals in Infection Control and Epidemiology 2010 position paper on safe injection, infusion, and medication vial practices in health care. Copyright © 2016 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

[Investigation on pattern and methods of quality control for Chinese materia medica based on dao-di herbs and bioassay - bioassay for Coptis chinensis].

Science.gov (United States)

Yan, Dan; Xiao, Xiao-he

2011-05-01

Establishment of bioassay methods is the technical issues to be faced with in the bioassay of Chinese materia medica. Taking the bioassay of Coptis chinensis Franch. as an example, the establishment process and application of the bioassay methods (including bio-potency and bio-activity fingerprint) were explained from the aspects of methodology, principle of selection, experimental design, method confirmation and data analysis. The common technologies were extracted and formed with the above aspects, so as to provide technical support for constructing pattern and method of the quality control for Chinese materia medica based on the dao-di herbs and bioassay.

Resin 90Y microsphere activity measurements for liver brachytherapy

International Nuclear Information System (INIS)

Dezarn, William A.; Kennedy, Andrew S.

2007-01-01

The measurement of the radioactivity administered to the patient is one of the major components of 90 Y microsphere liver brachytherapy. The activity of 90 Y microspheres in a glass delivery vial was measured in a dose calibrator. The calibration value to use for 90 Y in the dose calibrator was verified using an activity calibration standard provided by the microsphere manufacturer. This method allowed for the determination of a consistent, reproducible local activity standard. Additional measurements were made to determine some of the factors that could affect activity measurement. The axial response of the dose calibrator was determined by the ratio of activity measurements at the bottom and center of the dose calibrator. The axial response was 0.964 for a glass shipping vial, 1.001 for a glass V-vial, and 0.988 for a polycarbonate V-vial. Comparisons between activity measurements in the dose calibrator and those using a radiation survey meter were found to agree within 10%. It was determined that the dose calibrator method was superior to the survey meter method because the former allowed better defined measurement geometry and traceability of the activity standard back to the manufacturer. Part of the preparation of resin 90 Y microspheres for patient delivery is to draw out a predetermined activity from a shipping vial and place it into a V-vial for delivery to the patient. If the drawn activity was placed in a glass V-vial, the activity measured in the dose calibrator with a glass V-vial was 4% higher than the drawn activity from the shipping vial standard. If the drawn activity was placed in a polycarbonate V-vial, the activity measured in the dose calibrator with a polycarbonate V-vial activity was 20% higher than the drawn activity from the shipping vial standard. Careful characterization of the local activity measurement standard is recommended instead of simply accepting the calibration value of the dose calibrator manufacturer

Studies on Erythropoietin Bioassay Method

Energy Technology Data Exchange (ETDEWEB)

Cho, Kyoung Sam; Ro, Heung Kyu; Lee, Mun Ho [Seoul National University College of Medicine, Seoul (Korea, Republic of)

1975-09-15

It is the purpose of this paper to design the most preferable method of erythropoietin bioassay in Korea. Bioassay utilizing polycythemic mice are currently in general use for the indirect determination of erythropoietin. Assay animals are usually prepared either by transfusion or by exposure to reduced oxygen tension in specially constructed chamber. We prepared the polycythemic mice by the specially constructed hypobaric chamber. We observed weights and hematocrits of the mice in the hypobaric chamber, then hematocrits and 72 hours {sup 59}Fe red cell uptake ratio of the polycythemic mice induced by hypoxia after removal from the hypobaric chamber. We designed the method of erythropoietin bioassay according to the results obtained by above experiments. Then we measured the 72 hours {sup 59}Fe red cell uptake ratio of the polycythemic mice with normal saline, normal plasma and anemic plasma according to the method we designed. The results are followed:1) The hematocrits of the mice in hypobaric chamber increased to 74% in 11 days. It is preferable to maintain the pressure of the chamber to 400 mmHg for first 4 days then 300 mmHg for last 10 days to reduce the death rate and time consuming in hypobaric chamber. 2) After removal from the hypobaric chamber, the 72 hours {sup 59}Fe red cell uptake ratio decreased rapidly and maintained the lowest level from the fourth day to tenth day. 3) We design the method of erythropoietin bioassay according to the results of above experiment and to the half life of erythropoietin. 4) The Korean product {sup 59}Fe is mixture of {sup 55}Fe and {sup 59}Fe. And the {sup 59}Fe red cell uptake ratio in normal mice was far less with Korean product {sup 59}Fe than with pure {sup 59}Fe of foreign product. So it is desirable to use pure {sup 59}Fe in this method of erythropoietin bioassay. 5) Considering the cost, the technique, the time consuming and the sensitivity it is the most preferable method of erythropoietin bioassay in Korea

Análisis de la aplicación de una Auditoría de Seguridad Vial en carreteras concesionadas

OpenAIRE

Torres Márquez, Rolando Roque

2017-01-01

La tesis tiene como objetivo presentar y analizar la aplicación de una Auditoría de Seguridad Vial en un tramo de carretera concesionada ubicado al norte de la ciudad de Lima y que actualmente se encuentra en explotación. Para ello, se presentan los fundamentos conceptuales de la seguridad vial y la auditoría de Seguridad Vial acompañado de una breve explicación de los alcances y ventajas. Así mismo, se desarrollan las actividades que se ejecutaron en la auditoría y las actividades realizadas...

Iodination of monoclonal antibodies for diagnosis and radiotherapy using a convenient one vial method

International Nuclear Information System (INIS)

Haisma, H.J.; Hilgers, J.; Zurawski, V.R. Jr.

1986-01-01

We have developed a convenient system that can be used to iodinate monoclonal antibodies for diagnosis or therapy. A vial, previously coated with 1,3,4,6-tetrachloro-3a, 6a-diphenyl glycouril (iodogen), is used as a reaction vessel. Iodination and separation of bound and free iodide, using AG1-X8 ion exchange resin, are both accomplished in this vial. We found 90 +/- 4% of the iodide which was added was incorporated, respectively, into each of four different monoclonal antibodies evaluated. Approximately 90% of labeled antibody was recovered in each case. The monoclonal antibody OC125 was labeled to specific activities up to 25 mCi/mg. Immunoreactivities of 82 +/- 2% using 125 I and 66 +/- 5% using 131 I were achieved. As the radioiodination is done in one sealed vial and takes less than 15 min, this procedure is safe and can be performed in any nuclear medicine laboratory. The final product, which is sterile and apyrogenic, is suitable for diagnostic and radiotherapeutic applications

Evaluación vial y plan de rehabilitación y mantenimiento de la vía Azogues- Cojitambo- Déleg- La Raya

OpenAIRE

Garcés Velecela, Diana Patricia

2017-01-01

Contar con una infraestructura vial adecuada permite el desarrollo de cualquier región. De ahí que el mantenimiento de la infraestructura vial es importante para garantizar el buen funcionamiento de la misma. Considerando que en nuestro país durante los últimos años se ha tenido una gran inversión en proyectos viales y muchos de ellos al no tener un adecuado mantenimiento presentan daños prematuros, es necesario, por lo tanto, realizar la evaluación vial y establecer un plan de rehabilitación...

Study and determination of the influence factors of the radiopharmaceutical vials dimensions used for actimeter calibration at IPEN

International Nuclear Information System (INIS)

Martins, Elaine Wirney

2010-01-01

The efficiency and safety of the nuclear medicine practice depend, among others factors, of a quality control programme, mainly related to the use of the nuclide activity meters (activimeter). One of the most important sources of errors in the activimeter measurements is the thickness, size and volume of the vial that contains the radiopharmaceutical considering that a typical activimeter has its response dependent of the vial used. The objective of this work was to establish a quality control programme and the correction factors for the geometry of the vials used for distribution of radiopharmaceutical and activimeters calibration, considering that the Calibration Laboratory of Instruments (LCI) of the Instituto de Pesquisas Energeticas e Nucleares (IPEN) has a NPL-CRC Secondary Standard Radionuclide Calibrator System, manufactured for the Southern Scientific plc, compound by an ionization chamber well type and a current measurement system, with traceability to National Physical Laboratory (NPL) and calibrated with a P6 vial type with different dimensions of the one used for the IPEN. The radiopharmaceutical produced by IPEN 67 Ga, '1 31 I, 201 Tl and 99 mTc, had been tested using the two different vials. The results shown a maximum variation of 22% for 201 Tl, and the minimum variation was 2.98% for 131 I. The correction factors must be incorporated in the routine calibration of the activimeters. (author)

CRITERIOS E INDICADORES DE SOSTENIBILIDAD EN EL SUBSECTOR VIAL

Directory of Open Access Journals (Sweden)

Martha Melizza Ordoñez Díaz

2015-01-01

Full Text Available Actualmente en Colombia el desempeño de un contratista de obra se determina de acuerdo con los avances y resultados obtenidos en la construcción de la misma, mas no por su desempeño ambiental; sin embargo, cualquier tipo de obra civil se puede llevar a cabo con mayor o menor complejidad, dependiendo de la disponibilidad de recursos naturales en la zona y la visión que tenga la comunidad sobre el proyecto, de tal forma que la inversión económica y el tiempo de ejecución no solo dependerá de las actividades y costos netos de las obras civiles sino, además, de factores ambientales y sociales propios del lugar de ejecución. Con esta revisión bibliográfica sobre indicadores y guías ambientales internacionales, se pretende incentivar la sostenibilidad como eje transversal de los proyectos viales en Colombia, fortalecer las medidas de manejo socioambiental y mejorar el seguimiento y evaluación de los proyectos viales en el marco del equilibrio social, ambiental y económico que impulsa el desarrollo sostenible

Solvent Removal and Spore Inactivation Directly in Dispensing Vials with Supercritical Carbon Dioxide and Sterilant

OpenAIRE

Howell, Jahna; Niu, Fengui; McCabe, Shannon E.; Zhou, Wei; Decedue, Charles J.

2012-01-01

A process is described using supercritical carbon dioxide to extract organic solvents from drug solutions contained in 30-mL serum vials. We report drying times of less than 1 h with quantitative recovery of sterile drug. A six-log reduction of three spore types used as biological indicators is achieved with direct addition of peracetic acid to a final concentration of approximately 5 mM (~0.04 %) to the drug solution in the vial. Analysis of two drugs, acetaminophen and paclitaxel, indicated...

Protect Patients by Using Single- and Multi-Dose Vials Correctly

Centers for Disease Control (CDC) Podcasts

2014-07-10

CDC’s One & Only Campaign urges healthcare providers to recognize the differences between single-dose and multi-dose vials, and to understand appropriate use of each container type.  Created: 7/10/2014 by National Center for Emerging and Zoonotic Infectious Diseases (NCEZID).   Date Released: 7/10/2014.

Leaching of plastic polymers by plastic vials used for storing homoeopathic medicines: A preliminary study

Directory of Open Access Journals (Sweden)

Neeraj Gupta

2014-01-01

Full Text Available Background: In Homoeopathy, plastic containers/vials are used for the storing/dispensing of ethanol-based medicines instead of glass. Various studies have suggested that plastic components that leach out in stored substances tend to cause contamination and may produce adverse effects in living systems. The present study was aimed to find out chemical composition and leaching behaviour of commonly used plastic vials (PVs if any during the storage of ethanol-based homoeopathic medicines in optimal environment. Material and Methods: The experiments were conducted on two sample sets of PVs. Chemical properties of PV were assessed by Fourier Transform Infrared Attenuated Total Reflectance (FTIR-ATR spectroscopy. PV were cut separately [sample-1 (S-1 and sample-2 (S-2] and immersed in Homoeopathic Grade Ethanol (HGE in conical flask and stored for 7 days at ambient temperature (25° ± 5C with constant rotary shaking. After 7 days, S-1 and S-2 of PV in Homoeopathic Grade Ethanol (HGE were decanted and filtered. Aliquots (A1 and A2 were analysed by proton nuclear magnetic resonance spectroscopy (H 1 NMR. The spectral graph obtained by FTIR-ATR spectroscopy for PV compositions and spectral graph obtained by H 1 NMR spectroscopy for PV ethanol aliquots were examined for PVs material and PV leaching effect in HGE. Results: FTIR-ATR spectra showed that PV are made up of two types of polyolefin′s compounds i.e. Low Density Polyethylene (LDPE and Linear Low Density Polyethylene (LLDPE. Aliquots of PV in HGE showed the presence benzophenone and its methyl derivative, heat and light stabiliser (2, 2, 6, 6-tetramethylpiperidine and amino derivative, antioxidant (4, 4′- thiobis and 2-tertbutyl-5-methylphenol and plasticizer bis 2-Diethylhexyl phthalate (DEHP or Dioctyl phthalate (DOP. Results of study suggest that PVs leach out plastic polymers in HGE. Conclusion: This preliminary experiment suggests that it is not safe to use LDPE/LLDPE plastic for storing

Proteja a sus seres queridos de las lesiones viales

Centers for Disease Control (CDC) Podcasts

2008-12-10

Este podcast, que forma parte de la iniciativa Proteja a sus seres queridos, aborda las medidas que pueden tomar los padres de familia para ayudar a proteger a sus niños de las lesiones viales, una de las principales causas de lesiones infantiles.  Created: 12/10/2008 by National Center for Injury Prevention and Control (NCIPC).   Date Released: 4/1/2009.

Evaluation of different continuous cell lines in the isolation of mumps virus by the shell vial method from clinical samples

Science.gov (United States)

Reina, J; Ballesteros, F; Mari, M; Munar, M

2001-01-01

Aims—To compare prospectively the efficacy of the Vero, LLC-MK2, MDCK, Hep-2, and MRC-5 cell lines in the isolation of the mumps virus from clinical samples by means of the shell vial method. Methods—During an epidemic outbreak of parotiditis 48 clinical samples (saliva swabs and CSF) were studied. Two vials of the Vero, LLC-MK2, MDCK, MRC-5, and Hep-2 cell lines were inoculated with 0.2 ml of the samples by the shell vial assay. The vials were incubated at 36°C for two and five days. The vials were then fixed with acetone at -20°C for 10 minutes and stained by a monoclonal antibody against mumps virus by means of an indirect immunofluorescence assay. Results—The mumps virus was isolated from 36 samples. The Vero and LLC-MK2 cell lines showed a 100% isolation capacity, MDCK showed 77.7%, MRC-5 showed 44.4%, and Hep-2 showed 22.2%. The Vero and LLC-MK2 lines were significantly different to the other cell lines (p 5 infectious foci) were 94.4% for Vero, 97.2% for LLC-MK2, 5.5% for MDCK, 5.5% for Hep-2, and 0% for MRC-5. Conclusions—The Vero and LLC-MK2 cell lines are equally efficient at two and five days incubation for the isolation of the mumps virus from clinical samples, and the use of the shell vial method considerably shortens the time of aetiological diagnosis with higher specificity. Key Words: mumps virus • Vero cell line • LLC-MK2 cell line • MDCK cell line • Hep-2 cell line • MRC-5 cell line • isolation • shell vial PMID:11729211

Determination of geometry correction factors to different vials used to radiopharmaceutical activity measurements

International Nuclear Information System (INIS)

Kuahara, Lilian T.; Correa, Eduardo L.; Potiens, Maria da Penha A.

2015-01-01

The aim of this study is to present the geometry correction factors and their respective uncertainties to P6 and 10R vials and 3 mL and 5 mL plastic syringes using the reference activity meters present at the Laboratorio de Calibracao de Instrumentos (LCI), IPEN the secondary standard system Capintec NPL-CRC radionuclide calibrator, with traceability to the National Physics Laboratory (NPL), England and the work standard Capintec CRC-15BT and the Capintec CRC-25R. The procedure was made using 99m Tc, which is responsible for about 80 % of the routine procedures in a nuclear medicine service. Variations of up to 40 % between different vials using the same radionuclide were found. (author)

¡La calle también es mía! Los niños, las ciudades y la seguridad vial.

OpenAIRE

Alonso Plá, Francisco Manuel; Esteban Martínez, Cristina; Calatayud Miñana, Constanza; Alamar Rocatí, Beatriz

2009-01-01

El Instituto Universitario de Investigación en Tráfico y Seguridad Vial (INTRAS) y Attitudes (programa social de Audi), tras la publicación del libro "Los niños, las ciudades y la seguridad vial: una visión a partir de la investigación.", se plantearon como actividad complementaria la realización de unas jornadas que cumplieran los siguientes objetivos: • Permitir avanzar en el conocimiento y la implementación de medidas que contribuyan a una mejora de la seguridad vial en el caso concreto...

A mutation (L1014F) in the voltage-gated sodium channel of the grain aphid, Sitobion avenae, is associated with resistance to pyrethroid insecticides.

Science.gov (United States)

Foster, Stephen P; Paul, Verity L; Slater, Russell; Warren, Anne; Denholm, Ian; Field, Linda M; Williamson, Martin S

2014-08-01

The grain aphid, Sitobion avenae Fabricius (Hemiptera: Aphididae), is an important pest of cereal crops. Pesticides are the main method for control but carry the risk of selecting for resistance. In response to reports of reduced efficacy of pyrethroid sprays applied to S. avenae, field samples were collected and screened for mutations in the voltage-gated sodium channel, the primary target site for pyrethroids. Aphid mobility and mortality to lambda-cyhalothrin were measured in coated glass vial bioassays. A single amino acid substitution (L1014F) was identified in the domain IIS6 segment of the sodium channel from the S. avenae samples exhibiting reduced pyrethroid efficacy. Bioassays on aphids heterozygous for the kdr mutation (SR) or homozygous for the wild-type allele (SS) showed that those carrying the mutation had significantly lower susceptibility to lambda-cyhalothrin. The L1014F (kdr) mutation, known to confer pyrethroid resistance in many insect pests, has been identified for the first time in S. avenae. Clonal lines heterozygous for the mutation showed 35-40-fold resistance to lambda-cyhalothrin in laboratory bioassays, consistent with the reported effect of this mutation on pyrethroid sensitivity in other aphid species. © 2013 Society of Chemical Industry.

Vaccine vial stopper performance for fractional dose delivery of vaccines.

Science.gov (United States)

Jarrahian, Courtney; Myers, Daniel; Creelman, Ben; Saxon, Eugene; Zehrung, Darin

2017-07-03

Shortages of vaccines such as inactivated poliovirus and yellow fever vaccines have been addressed by administering reduced-or fractional-doses, as recommended by the World Health Organization Strategic Advisory Group of Experts on Immunization, to expand population coverage in countries at risk. We evaluated 3 kinds of vaccine vial stoppers to assess their performance after increased piercing from repeated withdrawal of doses needed when using fractional doses (0.1 mL) from presentations intended for full-dose (0.5 mL) delivery. Self-sealing capacity and fragmentation of the stopper were assessed via modified versions of international standard protocols. All stoppers maintained self-sealing capacity after 100 punctures. The damage to stoppers measured as the fragmentation rate was within the target of ≤ 10% of punctures resulting in a fragment after as many as 50 punctures. We concluded that stopper failure is not likely to be a concern if existing vaccine vials containing up to 10 regular doses are used up to 50 times for fractional dose delivery.

A specific bioassay for the inhibition of flowering.

Science.gov (United States)

Blake, J

1972-06-01

A bioassay for the inhibition of flowering involving the in vitro culture of excised, partially-induced, apices of Viscaria candida is described. This bioassay has been used to detect flowering inhibition in extracts from Kalanchoe blossfeldiana.

Bioassay of naturally occurring allelochemicals for phytotoxicity.

Science.gov (United States)

Leather, G R; Einhellig, F A

1988-10-01

The bioassay has been one of the most widely used tests to demonstrate allelopathic activity. Often, claims that a particular plant species inhibits the growth of another are based entirely on the seed germination response to solvent extracts of the suspected allelopathic plant; few of these tests are of value in demonstrating allelopathy under natural conditions. The veracity of the bioassay for evaluating naturally occurring compounds for phytotoxicity depends upon the physiological and biochemical response capacity of the bioassay organism and the mechanism(s) of action of the allelochemicals. The possibility that more than one allelochemical, acting in concert at very low concentrations, may be responsible for an observed allelopathic effect makes it imperative that bioassays be extremely sensitive to chemical growth perturbation agents. Among the many measures of phytotoxicity of allelochemicals, the inhibition (or stimulation) of seed germination, radicle elongation, and/or seedling growth have been the parameters of choice for most investigations. Few of these assays have been selected with the view towards the possible mechanism of the allelopathic effect.

A quality improvement project to reduce the intraoperative use of single-dose fentanyl vials across multiple patients in a pediatric institution.

Science.gov (United States)

Buck, David; Subramanyam, Rajeev; Varughese, Anna

2016-01-01

The use of a single-dose vial across multiple patients presents a risk to sterility and is against CDC guidelines. We initiated a quality improvement (QI) project to reduce the intraoperative use of single-dose vials of fentanyl across multiple patients at Cincinnati Children's Hospital Medical Center (CCHMC). The initial step of the improvement project was the development of a Key Driver Diagram. The diagram has the SMART aim of the project, key drivers inherent to the process we are trying to improve, and specific interventions targeting the key drivers. The number of patients each week receiving an IV dose of fentanyl, from a vial previously accessed for another patient was tracked in a high turnover operating room (OR). The improvement model used was based on the concept of building Plan-Do-Study-Act (PDSA) cycles. Tests of change included provider education, provision of an increased number of fentanyl vials, alternate wasting processes, and provision of single-use fentanyl syringes by the pharmacy. Prior to initiation of this project, it was common for a single fentanyl vial to be accessed for multiple patients. Our data showed an average percentage of failures of just over 50%. During the end of the project, after 7 months, the mean percentage failures had dropped to 5%. Preparation of 20 mcg single-use fentanyl syringes by pharmacy, combined with education of providers on appropriate use, was successful in reducing failures to below our goal of 25%. Appropriately sized fentanyl syringes prepared by pharmacy, education on correct use of single-dose vials, and reminders in the OR, reduced the percentage of patients receiving a dose of fentanyl from a vial previously accessed for another patient in a high-volume otolaryngology room. © 2015 John Wiley & Sons Ltd.

Herbicide impact on Hormosira banksii gametes measured by fluorescence and germination bioassays

International Nuclear Information System (INIS)

Seery, Cliff R.; Gunthorpe, Leanne; Ralph, Peter J.

2006-01-01

The innovative bioassay described here involves chlorophyll a fluorescence measurements of gametes from the macroalgae, Hormosira banksii, where gametes (eggs) were exposed to Diuron, Irgarol and Bromacil. Response was assessed as percent inhibition from control of effective quantum yield (ΔF/Fm') of photosystem II, herein referred to as % PSII Inhibition. This was measured with the dual-channelled pulse amplitude modulated (PAM) fluorometer, ToxY-PAM. The fluorescence bioassay was run simultaneously with an established H. banksii germination bioassay to compare sensitivity, precision, and time-to-result. The fluorescence bioassay gave highly sensitive results evidenced by EC 5 s (% PSII Inhibition) for Diuron, Irgarol and Bromacil being three, four and three orders of magnitude (respectively) lower than EC 5 s generated from the germination bioassays. Precision of the fluorescence bioassay was demonstrated with low coefficient of variations (<30%) for all three toxicants. With regard to time, the fluorescence bioassay gave results within 6 h, as opposed to more than 50 h for the germination bioassay. - Chlorophyll a fluorescence measurements form the basis of a macroalgal bioassay with many advantages over germination-based methods

Diagnostic doses and times for Phlebotomus papatasi and Lutzomyia longipalpis sand flies (Diptera: Psychodidae: Phlebotominae) using the CDC bottle bioassay to assess insecticide resistance.

Science.gov (United States)

Denlinger, David S; Creswell, Joseph A; Anderson, J Laine; Reese, Conor K; Bernhardt, Scott A

2016-04-15

Insecticide resistance to synthetic chemical insecticides is a worldwide concern in phlebotomine sand flies (Diptera: Psychodidae), the vectors of Leishmania spp. parasites. The CDC bottle bioassay assesses resistance by testing populations against verified diagnostic doses and diagnostic times for an insecticide, but the assay has been used limitedly with sand flies. The objective of this study was to determine diagnostic doses and diagnostic times for laboratory Lutzomyia longipalpis (Lutz & Nieva) and Phlebotomus papatasi (Scopoli) to ten insecticides, including pyrethroids, organophosphates, carbamates, and DDT, that are used worldwide to control vectors. Bioassays were conducted in 1,000-ml glass bottles each containing 10-25 sand flies from laboratory colonies of L. longipalpis or P. papatasi. Four pyrethroids, three organophosphates, two carbamates and one organochlorine, were evaluated. A series of concentrations were tested for each insecticide, and four replicates were conducted for each concentration. Diagnostic doses were determined only during the exposure bioassay for the organophosphates and carbamates. For the pyrethroids and DDT, diagnostic doses were determined for both the exposure bioassay and after a 24-hour recovery period. Both species are highly susceptible to the carbamates as their diagnostic doses are under 7.0 μg/ml. Both species are also highly susceptible to DDT during the exposure assay as their diagnostic doses are 7.5 μg/ml, yet their diagnostic doses for the 24-h recovery period are 650.0 μg/ml for Lu. longipalpis and 470.0 μg/ml for P. papatasi. Diagnostic doses and diagnostic times can now be incorporated into vector management programs that use the CDC bottle bioassay to assess insecticide resistance in field populations of Lu. longipalpis and P. papatasi. These findings provide initial starting points for determining diagnostic doses and diagnostic times for other sand fly vector species and wild populations using the CDC

Herbicide impact on Hormosira banksii gametes measured by fluorescence and germination bioassays

Energy Technology Data Exchange (ETDEWEB)

Seery, Cliff R. [Institute for Water and Environmental Resource Management, Department of Environmental Sciences, University of Technology, Sydney, Westbourne Street, Gore Hill, 2065 NSW (Australia); Gunthorpe, Leanne [Primary Industries Research Victoria (PIRVic), VIC (Australia); Ralph, Peter J. [Institute for Water and Environmental Resource Management, Department of Environmental Sciences, University of Technology, Sydney, Westbourne Street, Gore Hill, 2065 NSW (Australia)]. E-mail: peter.ralph@uts.edu.au

2006-03-15

The innovative bioassay described here involves chlorophyll a fluorescence measurements of gametes from the macroalgae, Hormosira banksii, where gametes (eggs) were exposed to Diuron, Irgarol and Bromacil. Response was assessed as percent inhibition from control of effective quantum yield ({delta}F/Fm') of photosystem II, herein referred to as % PSII Inhibition. This was measured with the dual-channelled pulse amplitude modulated (PAM) fluorometer, ToxY-PAM. The fluorescence bioassay was run simultaneously with an established H. banksii germination bioassay to compare sensitivity, precision, and time-to-result. The fluorescence bioassay gave highly sensitive results evidenced by EC{sub 5}s (% PSII Inhibition) for Diuron, Irgarol and Bromacil being three, four and three orders of magnitude (respectively) lower than EC{sub 5}s generated from the germination bioassays. Precision of the fluorescence bioassay was demonstrated with low coefficient of variations (<30%) for all three toxicants. With regard to time, the fluorescence bioassay gave results within 6 h, as opposed to more than 50 h for the germination bioassay. - Chlorophyll a fluorescence measurements form the basis of a macroalgal bioassay with many advantages over germination-based methods.

Determination of the influence factors of the radiopharmaceutical vials dimensions used for activimeter calibration at IPEN.

Science.gov (United States)

Martins, E W; Potiens, M P A

2012-07-01

This paper presents the establishment of a quality control program and correction factors for the geometry of the vials used for distribution of radiopharmaceutical and activimeters calibration. The radiopharmaceutical produced by IPEN 67Ga, 131I, 201Tl and 99mTc had been tested using two different vials. Results show a maximum variation of 22% for 201Tl, and the minimum variation was 2.98% for 131I. The correction factors must be incorporated in the routine calibration of the activimeters. Copyright © 2011 Elsevier Ltd. All rights reserved.

Applied in vitro radio bioassay

International Nuclear Information System (INIS)

Gaburo, J.C.G.; Sordi, G.M.A.A.

1992-11-01

The aim of this publication is to show the concepts and in vitro bioassay techniques as well as experimental procedures related with internal contamination evaluation. The main routes of intake, metabolic behavior, and the possible types of bioassay samples that can be collected for radionuclides analysis are described. Both biological processes and the chemical and physical behavior of the radioactive material of interest are considered and the capabilities of analytical techniques to detect and quantify the radionuclides are discussed. Next, the need of quality assurance throughout procedures are considered and finally a summary of the techniques applied to the internal routine monitoring of IPEN workers is given. (author)

Particulate Study on NeoProfen, a Neonatal Injectable Product.

Science.gov (United States)

Krishna, Aravind; Rice, Michael; Kester, Tom; Waters, Michael; Wilson, Terry

2016-01-01

NeoProfen or sterile ibuprofen L-lysine at 10 mg/mL ibuprofen, in 2 mL single-use Type I glass vials is often a first choice medication used to close a patent ductus arteriosus in neonatal patients from 500 to 1500 g body weight. Visible particulate matter was found in vials that were placed on a commercial stability program prior to the approved expiration date of 2 years. A combination of instrumental techniques including inductively coupled plasma-mass spectrometry, x-ray photoelectron spectroscopy, scanning electron microscopy energy dispersive x-ray spectrometry, and Raman and Fourier transform infrared microspectroscopy was used to evaluate stability, pilot batch and packaging samples in a root cause investigation. The particulate matter was shown to consist largely of ibuprofen aluminum salts of various stoichiometries. It developed over time by a substitution mechanism, in which the ibuprofen anion in solution reacts with the aluminum oxide network of the borosilicate glass giving the ibuprofen aluminum salt with =Al-OH remaining in the network. For corrective action an alternate Type I borosilicate glass vial with interior coating, not found in the original vial, was chosen for the product to prevent this occurrence. NeoProfen (sterile preservative-free ibuprofin L-lysine at 17 mg/mL in a single-use glass vial) is used to close a clinically significant patent ductus arteriosus in premature infants no more than 32 weeks gestational age. The neonatal population is especially sensitive to outside chemical, physical and environmental conditions because of incompletely developed organ systems, low birth weight and other underlying conditions. Two batches of this product were voluntarily recalled by the manufacturer, Lundbeck, and investigated for the source of particulate matter observed during a commercial stability testing program. This was found to result from an interaction between the product and the Type I borosilicate glass vial where ibuprofen

Time-to-positivity, type of culture media and oxidase test performed on positive blood culture vials to predict Pseudomonas aeruginosa in patients with Gram-negative bacilli bacteraemia.

Science.gov (United States)

Cobos-Triguero, N; Zboromyrska, Y; Morata, L; Alejo, I; De La Calle, C; Vergara, A; Cardozo, C; Arcas, M P; Soriano, A; Marco, F; Mensa, J; Almela, M; Martínez, J A

2017-02-01

The aim of this study was to determine the usefulness of oxidase test and time-to-positivity (TTP) in aerobic and anaerobic blood culture vials to detect the presence of Pseudomonas aeruginosa in patients with Gram-negative bacilli (GNB) bacteraemia. TTP was recorded for each aerobic and anaerobic blood culture vial of monomicrobial bacteraemia due to GNB. Oxidase test was performed in a pellet of the centrifuged content of the positive blood culture. An algorithm was developed in order to perform the oxidase test efficiently taking into account TTP and type of vial. A total of 341 episodes of GNB bacteraemia were analysed. Sensitivity, specificity, positive predictive value and negative predictive value of the oxidase test performed on positive vials with GNB to predict P. aeruginosa were 95%, 99%, 91%, and 99%, respectively. When growth was first or exclusively detected in anaerobic vials, P. aeruginosa was never identified hence the performance of the oxidase test could be avoided. When growth was only or first detected in aerobic vials, a TTP≥8h predicted P. aeruginosa in 37% or cases (63 of 169), therefore oxidase test is highly recommended. Oxidase test performed onto positive blood culture vials previously selected by TTP and type of vials is an easy and inexpensive way to predict P. aeruginosa. In most cases, this can lead to optimization of treatment in less than 24 hours.

Bioassay method for Uranium in urine by Delay Neutron counting

International Nuclear Information System (INIS)

Suratman; Purwanto; Sukarman-Aminjoyo

1996-01-01

A bioassay method for uranium in urine by neutron counting has been studied. The aim of this research is to obtain a bioassay method for uranium in urine which is used for the determination of internal dose of radiation workers. The bioassay was applied to the artificially uranium contaminated urine. The weight of the contaminant was varied. The uranium in the urine was irradiated in the Kartini reactor core, through pneumatic system. The delayed neutron was counted by BF3 neutron counter. Recovery of the bioassay was between 69.8-88.8 %, standard deviation was less than 10 % and the minimum detection was 0.387 μg

Complexing agents and pH influence on chemical durability of type I moulded glass containers.

Science.gov (United States)

Biavati, Alberto; Poncini, Michele; Ferrarini, Arianna; Favaro, Nicola; Scarpa, Martina; Vallotto, Marta

2017-06-16

Among the factors that affect the glass surface chemical durability, pH and complexing agents presence in aqueous solution have the main role (1). Glass surface attack can be also related to the delamination issue with glass particles appearance in the pharmaceutical preparation. A few methods to check for glass containers delamination propensity and some control guidelines have been proposed (2,3). The present study emphasizes the possible synergy between a few complexing agents with pH on the borosilicate glass chemical durability. Hydrolytic attack was performed in small volume 23 ml type I glass containers autoclaved according to EP or USP for 1 hour at 121°C, in order to enhance the chemical attack due to time, temperature and the unfavourable surface/volume ratio. 0,048 M or 0.024 M (moles/liter) solutions of the acids citric, glutaric, acetic, EDTA (ethylenediaminetetraacetic acid) and sodium phosphate with water for comparison, were used for the trials. The pH was adjusted ± 0,05 units at fixed values 5,5-6,6-7-7,4-8-9 by LiOH diluted solution. Since silicon is the main glass network former, silicon release into the attack solutions was chosen as the main index of the glass surface attack and analysed by ICPAES. The work was completed by the analysis of the silicon release in the worst attack conditions, of moulded glass, soda lime type II and tubing borosilicate glass vials to compare different glass compositions and forming technologies. Surface analysis by SEM was finally performed to check for the surface status after the worst chemical attack condition by citric acid. Copyright © 2017, Parenteral Drug Association.

Biodegradation of [14C]phenol in secondary sewage and landfill leachate measured by double-vial radiorespirometry

International Nuclear Information System (INIS)

Deeley, G.M.; Skierkowski, P.; Robertson, J.M.

1985-01-01

Double-vial radiorespirometry was used to estimate the biodegradation rates of 14 C-labeled phenol in a landfill leachate and a secondary treated domestic wastewater. Rates were found to be comparable for each material at each of the three concentrations tested. Sewage microorganisms immediately began biodegrading the [ 14 C]phenol; landfill leachate microorganisms required a lag period before maximum biodegradation of the [ 14 C]phenol. The apparent rate of [ 14 C]phenol biodegradation was 2.4 times faster in the sewage than in the landfill leachate. Double-vial radiorespirometry was shown to be an effective method for screening biodegradation rates in aquifers

La Eficacia Publicitaria en las Campañas de Prevención para la Seguridad Vial

OpenAIRE

Serrano Cordero, Julia Catalina; Arévalo Peña, José David

2017-01-01

Este artículo aborda la importancia de los procesos de evaluación de los resultados en las campañas de educación y seguridad vial, éstos, si bien, han alcanzado notables progresos en la praxis, evidencian una falta de información en cuanto a la pertinencia e idoneidad de las herramientas de comunicación en prevención. El objetivo fue validar una campaña de educación y seguridad vial implementada por la Empresa Municipal de Tránsito y Transporte de la ciudad de Cuenca (Ecuador), en el año 2014...

Bioassay Phantoms Using Medical Images and Computer Aided Manufacturing

International Nuclear Information System (INIS)

Xu, X. Geroge

2011-01-01

A radiation bioassay program relies on a set of standard human phantoms to calibrate and assess radioactivity levels inside a human body for radiation protection and nuclear medicine imaging purposes. However, the methodologies in the development and application of anthropomorphic phantoms, both physical and computational, had mostly remained the same for the past 40 years. We herein propose a 3-year research project to develop medical image-based physical and computational phantoms specifically for radiation bioassay applications involving internally deposited radionuclides. The broad, long-term objective of this research was to set the foundation for a systematic paradigm shift away from the anatomically crude phantoms in existence today to realistic and ultimately individual-specific bioassay methodologies. This long-term objective is expected to impact all areas of radiation bioassay involving nuclear power plants, U.S. DOE laboratories, and nuclear medicine clinics.

Comparison of five bioassay techniques for assessing sediment-bound contaminants

OpenAIRE

Ahlf, Wolfgang; Calmano, Wolfgang; Erhard, Judith; Förstner, Ulrich

1989-01-01

Biological response could not be predicted based on chemical concentration of the sediment contaminants. Bioassays integrate the response of test organisms to contaminants and nutrients. Comparative results of five acute bioassays indicated that Neubauer phytoassay was the most sensitive. The mircobial biomass and algal growth tests indicated a response to the availability of contaminants and nutrients. These results suggest the usefulness of a diversity of bioassays in toxicity testing of se...

Internal dosimetry performing dose assessments via bioassay measurements

International Nuclear Information System (INIS)

Bailey, K.M.

1993-01-01

The Internal Dosimetry Department at the Y-12 Plant maintains a state-of-the-art bioassay program managed under the guidance and regulations of the Department of Energy. The two major bioassay techniques currently used at Y-12 are the in vitro (urinalysis) and in vivo (lung counting) programs. Fecal analysis (as part of the in vitro program) is another alternative; however, since both urine and fecal analysis provide essentially the same capabilities for detecting exposures to uranium, the urinalysis is the main choice primarily for aesthetic reasons. The bioassay frequency is based on meeting NCRP 87 objectives which are to monitor the accumulation of radioactive material in exposed individuals, and to ensure that significant depositions are detected

Development of a correction factor for Xe-133 vials for use with a dose calibrator

International Nuclear Information System (INIS)

Gels, G.L.; Piltingsrud, H.V.

1982-01-01

Manufacturers of dose calibrators who give calibration settings for various radionuclies sometimes do not specify the type of radionuclide container the calibration is for. The container, moreover, may not be of the same type as those a user might purchase. When these factors are not considered, the activity administered to the patient may be significantly different from that intended. An experiment is described in which calibration factors are determined for measurement of Xe-133 activity in vials in a dose calibrator. This was accomplished by transferring the Xe-133 from the commercial vials to standard NBS calibration ampules. Based on ten such transfers, the resulting correction factor for the dose calibrator was 1.22

Red Vial de Nicaragua (Optimización y Mantenimiento)

OpenAIRE

Wilfredo Martínez

2013-01-01

La red vial es un patrimonio nacional, el cual es necesario: proteger, conservar, aumentar y mejorar; para apoyar eldesarrollo socioeconómico de nuestro país. La actividad de mantenimiento, constituye un factor determinante quegarantiza la operación satisfactoria del transporte durante la vida útil de los caminos; en sus diferentes modalidades. La ausencia de un mantenimiento preventivo y de un mantenimiento correctivo tardío, conduce a que la inversiónrealizada sufra una depreciación más ac...

Collection and control of tritium bioassay samples at Pantex

International Nuclear Information System (INIS)

Fairrow, N.L.; Ivie, W.E.

1992-01-01

Pantex is the final assembly/disassembly point for US nuclear weapons. The Pantex internal dosimetry section monitors radiation workers once a month for tritium exposure. In order to manage collection and control of the bioassay specimens efficiently, a bar code system for collection of samples was developed and implemented to speed up the process and decrease the number of errors probable when transferring data. In the past, all the bioassay data from samples were entered manually into a computer database. Transferring the bioassay data from the liquid scintillation counter to each individual's dosimetry record required as much as two weeks of concentrated effort

LA IMPORTANCIA DE LOS EJES DE FIJACIÓN DEL PAISAJE URBANO EN LA EDUCACIÓN VIAL

OpenAIRE

Nina, Mónica Marianela; Filippeti, Rosana; Pauletto, Selva del Valle

2012-01-01

La enseñanza de los ejes de fijación en el espacio urbano son elementos que deben ser vinculados con la educación vial ya que la misma no forma parte del diseño curricular en la educación formal. El propósito del presente trabajo es que a través de la enseñanza de las funciones de las arterias de circulación como calles, avenidas, rutas, autopistas se busca la toma de conciencia de los jóvenes de la importancia de conocer los principios de la educación vial para prevenir los accidentes de trá...

Bioassays for risk assessment of coal conversion products

Energy Technology Data Exchange (ETDEWEB)

Schacht, S.; Sinder, C.; Pfeifer, F.; Klein, J. [DMT-Gesellschaft fuer Forschung und Pruefung mbH, Essen (Germany)

1999-07-01

Traditional as well as biotechnological processing coal leads to complex mixtures of products. Besides chemical and physical characterization, which provides the information for product application, there is a need for bioassays to monitor properties that are probably toxic, mutagenic or cancerogenic. Investigations carried out focused on the selection, adaptation and validation of bioassays for the sensitive estimation of toxic effects. Organisms like bacteria, Daphnia magna and Scenedesmus subspicatus, representing different complexities in the biosphere, were selected as test systems for ecotoxicological and mutagenicity studies. The results obtained indicate that bioassays are, in principle, suitable tools for characterization and evaluation of coal-derived substances and bioconversion products. Using coal products, coal-relevant model compounds and bioconversion products, data for risk assessment are presented. (orig.)

The BIDAS: bioassay data analysis software for evaluating radionuclide intake and dose

International Nuclear Information System (INIS)

Lee, Tae Young; Lee, Jong Il; Chang, Si Young

2003-01-01

The BIDAS (BIoassay Data Analysis Software) computer code was developed for the interpretation of bioassay measurements in terms of the intake and dose using the International Commission on Radiological Protection's(ICRP's) currently recommended respiratory tract, GI-tract and biokinetic models to describe the behavior of the radioactive materials within the body. The code consists of a data base module to the manage bioassay data, a data base module containing the predicted bioassay quantities of each radionuclide, and a computational module to the estimate radionuclide intake and dose from either an acute or a chronic exposure based on the measured bioassay quantities. This paper describes the features of the code as well as the results of the BIDAS validation

Preparation of one-vial reduced anti-CEA kit

International Nuclear Information System (INIS)

Hamada, Elena Setuko; Muramoto, Emiko; Shiraishi, Emilia Mayumi; Silva, Licia Maria Britto da; Martins, Heidi Pinto; Silva, Constanca Pagano Goncalves da

1996-01-01

A rapid and reliable instant reduced anti-CEA lyophilized kit for labelling with 99m Tc was developed. Each vial contains 0.5 mg of reduced anti-CEA, 40 μg of mendronate (MDP), 2.75 μg stannous fluoride (Sn F 2 ) and 15 μ g p-aminobenzoic acid (PABA). Labeling efficiency and stability were higher than 95% and were determined by instant paper chromatography. Biodistribution studies were performed in normal isogenic BALB/c mice at 4,6 and 24 hours after intravenous administration of the radiolabelled product. The maximum amount of activity was accumulated in the liver followed by intestines and kidneys. (author)

Selección de alternativas de inversión en la construcción de obras viales en la ciudad de México

OpenAIRE

Palomas-Molina, X.; Álvarez-Icaza, L.

2010-01-01

Se propone un método sistemático con el que se analiza un conjunto de nodos viales de la ciudad de México con altos índices de ocupación para decidir sobre la posible realización de algunos tipos de obras viales en los mismos. El método permite obtener, a través del análisis estadístico de información y de la programación entera, las mejores opciones para invertir en la construcción de estas obras viales bajo un escenario de recursos limitados. La decisión se toma por un lado, con base en los...

Determination of {sup 226}Ra by gamma spectrometry: study of packaging vial of sample for analysis; Determinacao de {sup 226}Ra por espectrometria gama: estudo do recipiente de acondicionamento de amostra para analise

Energy Technology Data Exchange (ETDEWEB)

Carneiro, Andre Cavalcanti

2015-07-01

Determination of radioactivity levels of {sup 226}Ra by gamma spectrometry in a sample is based on measurements of {sup 214}Pb and {sup 214}Bi, daughters of {sup 222}Rn. Because radon is a gas, it can leak from the sample vial or accumulate on the upper empty it. If the vial has any crack, there will be loss of gas, which will cause error in determining the {sup 226}Ra concentration. One possible cause of cracks in the vials, that houses standards and samples, is the radiolysis action in the vial material, usually a polymer. As the demand {sup 226}Ra analysis in different matrices (geological samples, food, plants, etc.) is increasing, it was decided to study some polymer vials available on the market, to verify the feasibility to be used when is applied the analysis method using gamma spectrometry. Four types of polymer vials have been studied. The radiation doses in walls of the vials caused by natural radionuclides present in the sample were simulated using gamma irradiation. Tests, such as compressive strength test and tightness, were applied to the irradiated and non-irradiated vials. First, to verify the effect of radiolysis on the vial material and also if there was {sup 222}Rn diffusion in their walls. These preliminary results pointed out that the acrylic vials are the best option of packaging samples for analysis. This study should be repeated in a larger number of samples for a better evaluation. (author)

Fluorescence-Based Bioassays for the Detection and Evaluation of Food Materials

OpenAIRE

Nishi, Kentaro; Isobe, Shin-Ichiro; Zhu, Yun; Kiyama, Ryoiti

2015-01-01

We summarize here the recent progress in fluorescence-based bioassays for the detection and evaluation of food materials by focusing on fluorescent dyes used in bioassays and applications of these assays for food safety, quality and efficacy. Fluorescent dyes have been used in various bioassays, such as biosensing, cell assay, energy transfer-based assay, probing, protein/immunological assay and microarray/biochip assay. Among the arrays used in microarray/biochip assay, fluorescence-based mi...

Crystal Nucleation Using Surface-Energy-Modified Glass Substrates.

Science.gov (United States)

Nordquist, Kyle A; Schaab, Kevin M; Sha, Jierui; Bond, Andrew H

2017-08-02

Systematic surface energy modifications to glass substrates can induce nucleation and improve crystallization outcomes for small molecule active pharmaceutical ingredients (APIs) and proteins. A comparatively broad probe for function is presented in which various APIs, proteins, organic solvents, aqueous media, surface energy motifs, crystallization methods, form factors, and flat and convex surface energy modifications were examined. Replicate studies ( n ≥ 6) have demonstrated an average reduction in crystallization onset times of 52(4)% (alternatively 52 ± 4%) for acetylsalicylic acid from 91% isopropyl alcohol using two very different techniques: bulk cooling to 0 °C using flat surface energy modifications or microdomain cooling to 4 °C from the interior of a glass capillary having convex surface energy modifications that were immersed in the solution. For thaumatin and bovine pancreatic trypsin, a 32(2)% reduction in crystallization onset times was demonstrated in vapor diffusion experiments ( n ≥ 15). Nucleation site arrays have been engineered onto form factors frequently used in crystallization screening, including microscope slides, vials, and 96- and 384-well high-throughput screening plates. Nucleation using surface energy modifications on the vessels that contain the solutes to be crystallized adds a layer of useful variables to crystallization studies without requiring significant changes to workflows or instrumentation.

A rapid bioassay for detecting saxitoxins using a Daphnia acute toxicity test

Energy Technology Data Exchange (ETDEWEB)

Ferrao-Filho, Aloysio da S., E-mail: aloysio@ioc.fiocruz.b [Laboratorio de Avaliacao e Promocao da Saude Ambiental, Departamento de Biologia, Instituto Oswaldo Cruz, FIOCRUZ, Av. Brasil 4365, Manguinhos, Rio de Janeiro, RJ 21045-900 (Brazil); Soares, Maria Carolina S., E-mail: mcarolsoares@gmail.co [Departamento de Engenharia Sanitaria e Ambiental Faculdade de Engenharia, Universidade Federal de Juiz de Fora, Juiz de Fora, MG 36036-900 (Brazil); Freitas de Magalhaes, Valeria, E-mail: valeria@biof.ufrj.b [Laboratorio de Ecofisiologia e Toxicologia de Cianobacterias, Instituto de Biofisica Carlos Chagas Filho, CCS, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Rio de Janeiro, RJ 21949-900 (Brazil); Azevedo, Sandra M.F.O., E-mail: sazevedo@biof.ufrj.b [Laboratorio de Ecofisiologia e Toxicologia de Cianobacterias, Instituto de Biofisica Carlos Chagas Filho, CCS, Universidade Federal do Rio de Janeiro, Ilha do Fundao, Rio de Janeiro, RJ 21949-900 (Brazil)

2010-06-15

Bioassays using Daphnia pulex and Moina micrura were designed to detect cyanobacterial neurotoxins in raw water samples. Phytoplankton and cyanotoxins from seston were analyzed during 15 months in a eutrophic reservoir. Effective time to immobilize 50% of the exposed individuals (ET{sub 50}) was adopted as the endpoint. Paralysis of swimming movements was observed between approx0.5-3 h of exposure to lake water containing toxic cyanobacteria, followed by an almost complete recovery of the swimming activity within 24 h after being placed in control water. The same effects were observed in bioassays with a saxitoxin-producer strain of Cylindrospermopsis raciborskii isolated from the reservoir. Regression analysis showed significant relationships between ET{sub 50}vs. cell density, biomass and saxitoxins content, suggesting that the paralysis of Daphnia in lake water samples was caused by saxitoxins found in C. raciborskii. Daphnia bioassay was found to be a sensitive method for detecting fast-acting neurotoxins in natural samples, with important advantages over mouse bioassays. - A new Daphnia bioassay, as an alternative to the mouse bioassay, is able to detect effects of fast-acting, potent neurotoxins in raw water.

A rapid bioassay for detecting saxitoxins using a Daphnia acute toxicity test

International Nuclear Information System (INIS)

Ferrao-Filho, Aloysio da S.; Soares, Maria Carolina S.; Freitas de Magalhaes, Valeria; Azevedo, Sandra M.F.O.

2010-01-01

Bioassays using Daphnia pulex and Moina micrura were designed to detect cyanobacterial neurotoxins in raw water samples. Phytoplankton and cyanotoxins from seston were analyzed during 15 months in a eutrophic reservoir. Effective time to immobilize 50% of the exposed individuals (ET 50 ) was adopted as the endpoint. Paralysis of swimming movements was observed between ∼0.5-3 h of exposure to lake water containing toxic cyanobacteria, followed by an almost complete recovery of the swimming activity within 24 h after being placed in control water. The same effects were observed in bioassays with a saxitoxin-producer strain of Cylindrospermopsis raciborskii isolated from the reservoir. Regression analysis showed significant relationships between ET 50 vs. cell density, biomass and saxitoxins content, suggesting that the paralysis of Daphnia in lake water samples was caused by saxitoxins found in C. raciborskii. Daphnia bioassay was found to be a sensitive method for detecting fast-acting neurotoxins in natural samples, with important advantages over mouse bioassays. - A new Daphnia bioassay, as an alternative to the mouse bioassay, is able to detect effects of fast-acting, potent neurotoxins in raw water.

Solvent removal and spore inactivation directly in dispensing vials with supercritical carbon dioxide and sterilant.

Science.gov (United States)

Howell, Jahna; Niu, Fengui; McCabe, Shannon E; Zhou, Wei; Decedue, Charles J

2012-06-01

A process is described using supercritical carbon dioxide to extract organic solvents from drug solutions contained in 30-mL serum vials. We report drying times of less than 1 h with quantitative recovery of sterile drug. A six-log reduction of three spore types used as biological indicators is achieved with direct addition of peracetic acid to a final concentration of approximately 5 mM (~0.04 %) to the drug solution in the vial. Analysis of two drugs, acetaminophen and paclitaxel, indicated no drug degradation as a result of the treatment. Furthermore, analysis of the processed drug substance showed that no residual peracetic acid could be detected in the final product. We have demonstrated an effective means to simultaneously dry and sterilize active pharmaceutical ingredients from organic solvents directly in a dispensing container.

La Webquest como innovación educativa en el ámbito de la educación vial

Directory of Open Access Journals (Sweden)

Rosa María GOIG MARTÍNEZ

2013-01-01

Full Text Available La Educación Vial en las edades tempranas se puede implementar a través de cuentos, talleres, rincones de juego, patios de recreo, salidas extraescolares, actividades de psicomotricidad. Sin embargo, es importante destacar el papel de las Tecnologías de la Información y la Comunicación en el enriquecimiento de las propuestas de aula en relación a la Educación Vial, tomándolas como recurso complementario, en nuestro contexto, la Webquest. Sin olvidar la necesidad de seguir trabajando con los niños y las niñas situaciones reales ligadas a sus experiencias vitales en materia de Educación Vial, pues el mundo real nunca debiera ser desplazado por el mundo virtual en ningún caso, máxime si tenemos en cuenta que se trata de la etapa de Educación Infantil. El objetivo general de este artículo es corroborar que la Webquest constituye una auténtica oportunidad para innovar en el ámbito de la Educación Vial, ofreciendo al alumnado experiencias didácticas coherentes y complementarias desde la etapa de Educación Infantil. La metodología, de carácter cuantitativo y cualitativo, se desarrolló a través de la aplicación de un cuestionario, de una entrevista, del análisis documental y su triangulación, finalizando con el análisis de los datos obtenidos. Una de las conclusiones obtenidas expone que la Webquest es un recurso que nos facilita el proceso de enseñanza-aprendizaje y aumenta la motivación tanto en alumnos como en agentes educativos.

Structuring a risk-based bioassay program for uranium usage in university laboratories

Science.gov (United States)

Dawson, Johnne Talia

Bioassay programs are integral in a radiation safety program. They are used as a method of determining whether individuals working with radioactive material have been exposed and have received a resulting dose. For radionuclides that are not found in nature, determining an exposure is straightforward. However, for a naturally occurring radionuclide like uranium, it is not as straightforward to determine whether a dose is the result of an occupational exposure. The purpose of this project is to address this issue within the University of Nevada, Las Vegas's (UNLV) bioassay program. This project consisted of two components that studied the effectiveness of a bioassay program in determining the dose for an acute inhalation of uranium. The first component of the plan addresses the creation of excretion curves, utilizing MATLAB that would allow UNLV to be able to determine at what time an inhalation dose can be attributed to. The excretion curves were based on the ICRP 30 lung model, as well as the Annual Limit Intake (ALI) values located in the Nuclear Regulatory Commission's 10CFR20 which is based on ICRP 30 (International Commission on Radiological Protection). The excretion curves would allow UNLV to be able to conduct in-house investigations of inhalation doses without solely depending on outside investigations and sources. The second component of the project focused on the creation of a risk based bioassay program to be utilized by UNLV that would take into account bioassay frequency that depended on the individual. Determining the risk based bioassay program required the use of baseline variance in order to minimize the investigation of false positives among those individuals who undergo bioassays for uranium work. The proposed program was compared against an evaluation limit of 10 mrem per quarter, an investigational limit of 125 mrem per quarter, and the federal/state requirement of 1.25 rem per quarter. It was determined that a bioassay program whose bioassay

Desarrollo de proyectos viales y aportes del estado en terrenos

OpenAIRE

Beatriz Marulanda; Miguel Montes

2004-01-01

Este artículo tiene como objetivo central identificar las condiciones bajo las cuales es factible que el aporte estatal a un proyecto vial (en el contexto de asociaciones público privadas) esté representado por cesión de terrenos y derechos de uso exclusivo de los mismos en zonas aledañas a una carretera concesionada. En el desarrollo del trabajo, se busca, en particular: 1) Identificar los aspectos críticos que se deben prever para organizar los concursos, valorar y negociar los aportes públ...

Hacia el desarrollo sostenible en la seguridad vial : el caso holandés.

NARCIS (Netherlands)

Wegman, F.C.M.

1999-01-01

En esta ponencia, se hace un estudio general sobre la Seguridad Vial en los Países Bajos, mostrando la evolución del indice de accidentes. Se indican cuales son los objetivos fijados por el Gobierno neerlandés y la estrategia a seguir desde el punto de vista político. Aparece el concepto de

Validation of a Novel Bioassay for Low-level Perchlorate Determination

Science.gov (United States)

2014-04-01

was not attractive, since these reduce PMS2 , and it was thought they would interfere with the stoichiometry of NADH and perchlorate in the bioassay...these reduce PMS2 directly, and would interfere with the stoichiometry of NADH and perchlorate in the bioassay. Thus the only approach that could be

The effect of pesticide residue on caged mosquito bioassays.

Science.gov (United States)

Barber, J A S; Greer, Mike; Coughlin, Jamie

2006-09-01

Wind tunnel experiments showed that secondary pickup of insecticide residue by mosquitoes in cage bioassays had a significant effect on mortality. Cage bioassays using adult Ochlerotatus taeniorhynchus (Wiedemann) investigated the effect of exposure time to a contaminated surface. Cages were dosed in a wind tunnel using the LC50 for naled (0.124 mg a.i./ml) and an LC25 (0.0772 mg a.i./ml) for naled. Half of the bioassay mosquitoes were moved directly into clean cages with the other half remaining in the sprayed, hence contaminated, cage. Treatment mortality was assessed at 8, 15, 30, 60, 120, 240, and 1,440 min postapplication. Cage contamination had a significant effect on mosquito mortality for both the LC25 and LC50 between 15 and 30 min postapplication.

Integration of laboratory bioassays into the risk-based corrective action process

International Nuclear Information System (INIS)

Edwards, D.; Messina, F.; Clark, J.

1995-01-01

Recent data generated by the Gas Research Institute (GRI) and others indicate that residual hydrocarbon may be bound/sequestered in soil such that it is unavailable for microbial degradation, and thus possibly not bioavailable to human/ecological receptors. A reduction in bioavailability would directly equate to reduced exposure and, therefore, potentially less-conservative risk-based cleanup soil goals. Laboratory bioassays which measure bioavailability/toxicity can be cost-effectively integrated into the risk-based corrective action process. However, in order to maximize the cost-effective application of bioassays several site-specific parameters should be addressed up front. This paper discusses (1) the evaluation of parameters impacting the application of bioassays to soils contaminated with metals and/or petroleum hydrocarbons and (2) the cost-effective integration of bioassays into a tiered ASTM type framework for risk-based corrective action

Development and validation of microbial bioassay for quantification of Levofloxacin in pharmaceutical preparations

Directory of Open Access Journals (Sweden)

Nishant A. Dafale

2015-02-01

Full Text Available The aim of this study was to develop and validate a simple, sensitive, precise and cost-effective one-level agar diffusion (5+1 bioassay for estimation of potency and bioactivity of Levofloxacin in pharmaceutical preparation which has not yet been reported in any pharmacopoeia. Among 16 microbial strains, Bacillus pumilus ATCC-14884 was selected as the most significant strain against Levofloxacin. Bioassay was optimized by investigating several factors such as buffer pH, inoculums concentration and reference standard concentration. Identification of Levofloxacin in commercial sample Levoflox tablet was done by FTIR spectroscopy. Mean potency recovery value for Levofloxacin in Levoflox tablet was estimated as 100.90%. A validated bioassay method showed linearity (r2=0.988, precision (Interday RSD=1.05%, between analyst RSD=1.02% and accuracy (101.23%, RSD=0.72%. Bioassay was correlated with HPLC using same sample and estimated potencies were 100.90% and 99.37%, respectively. Results show that bioassay is a suitable method for estimation of potency and bioactivity of Levofloxacin pharmaceutical preparations. Keywords: Levofloxacin, Antibiotic resistance, Microbiological bioassay, HPLC, Pharmacopoeia

Mixed gamma emitting gas standard and method

International Nuclear Information System (INIS)

McFarland, R.C.; McFarland, P.A.

1986-01-01

The invention in one aspect pertains to a method of calibrating gamma spectroscopy systems for gas counting in a variety of counting containers comprising withdrawing a precision volume of a mixed gamma-emitting gas standard from a precision volume vial and delivering the withdrawn precision volume of the gas standard to the interior of a gas counting container. Another aspect of the invention pertains to a mixed gamma-emitting gas standard, comprising a precision spherical vial of predetermined volume, multiple mixed emitting gas components enclosed within the vial, and means for withdrawing from the vial a predetermined amount of the components wherein the gas standard is used to calibrate a gamma spectrometer system for gas counting over a wide energy range without the use of additional standards. A third aspect comprehends a gamma spectrometer calibration system for gas counting, comprising a precision volume spherical glass vial for receiving mixed multiisotope gas components, and two tubular arms extending from the vial. A ground glass stopcock is positioned on each arm, and the outer end of one arm is provided with a rubber septum port

DWPF Sample Vial Insert Study-Statistical Analysis of DWPF Mock-Up Test Data

Energy Technology Data Exchange (ETDEWEB)

Harris, S.P. [Westinghouse Savannah River Company, AIKEN, SC (United States)

1997-09-18

This report is prepared as part of Technical/QA Task Plan WSRC-RP-97-351 which was issued in response to Technical Task Request HLW/DWPF/TTR-970132 submitted by DWPF. Presented in this report is a statistical analysis of DWPF Mock-up test data for evaluation of two new analytical methods which use insert samples from the existing HydragardTM sampler. The first is a new hydrofluoric acid based method called the Cold Chemical Method (Cold Chem) and the second is a modified fusion method.Either new DWPF analytical method could result in a two to three fold improvement in sample analysis time.Both new methods use the existing HydragardTM sampler to collect a smaller insert sample from the process sampling system. The insert testing methodology applies to the DWPF Slurry Mix Evaporator (SME) and the Melter Feed Tank (MFT) samples.The insert sample is named after the initial trials which placed the container inside the sample (peanut) vials. Samples in small 3 ml containers (Inserts) are analyzed by either the cold chemical method or a modified fusion method. The current analytical method uses a HydragardTM sample station to obtain nearly full 15 ml peanut vials. The samples are prepared by a multi-step process for Inductively Coupled Plasma (ICP) analysis by drying, vitrification, grinding and finally dissolution by either mixed acid or fusion. In contrast, the insert sample is placed directly in the dissolution vessel, thus eliminating the drying, vitrification and grinding operations for the Cold chem method. Although the modified fusion still requires drying and calcine conversion, the process is rapid due to the decreased sample size and that no vitrification step is required.A slurry feed simulant material was acquired from the TNX pilot facility from the test run designated as PX-7.The Mock-up test data were gathered on the basis of a statistical design presented in SRT-SCS-97004 (Rev. 0). Simulant PX-7 samples were taken in the DWPF Analytical Cell Mock

Risk of Injection-Site Abscess among Infants Receiving a Preservative-Free, Two-Dose Vial Formulation of Pneumococcal Conjugate Vaccine in Kenya

Science.gov (United States)

Burton, Deron C.; Bigogo, Godfrey M.; Audi, Allan O.; Williamson, John; Munge, Kenneth; Wafula, Jackline; Ouma, Dominic; Khagayi, Sammy; Mugoya, Isaac; Mburu, James; Muema, Shadrack; Bauni, Evasius; Bwanaali, Tahreni; Feikin, Daniel R.; Ochieng, Peter M.; Mogeni, Ondari D.; Otieno, George A.; Olack, Beatrice; Kamau, Tatu; Van Dyke, Melissa K.; Chen, Robert; Farrington, Paddy; Montgomery, Joel M.; Breiman, Robert F.; Scott, J. Anthony G.; Laserson, Kayla F.

2015-01-01

There is a theoretical risk of adverse events following immunization with a preservative-free, 2-dose vial formulation of 10-valent-pneumococcal conjugate vaccine (PCV10). We set out to measure this risk. Four population-based surveillance sites in Kenya (total annual birth cohort of 11,500 infants) were used to conduct a 2-year post-introduction vaccine safety study of PCV10. Injection-site abscesses occurring within 7 days following vaccine administration were clinically diagnosed in all study sites (passive facility-based surveillance) and, also, detected by caregiver-reported symptoms of swelling plus discharge in two sites (active household-based surveillance). Abscess risk was expressed as the number of abscesses per 100,000 injections and was compared for the second vs first vial dose of PCV10 and for PCV10 vs pentavalent vaccine (comparator). A total of 58,288 PCV10 injections were recorded, including 24,054 and 19,702 identified as first and second vial doses, respectively (14,532 unknown vial dose). The risk ratio for abscess following injection with the second (41 per 100,000) vs first (33 per 100,000) vial dose of PCV10 was 1.22 (95% confidence interval [CI] 0.37–4.06). The comparator vaccine was changed from a 2-dose to 10-dose presentation midway through the study. The matched odds ratios for abscess following PCV10 were 1.00 (95% CI 0.12–8.56) and 0.27 (95% CI 0.14–0.54) when compared to the 2-dose and 10-dose pentavalent vaccine presentations, respectively. In Kenya immunization with PCV10 was not associated with an increased risk of injection site abscess, providing confidence that the vaccine may be safely used in Africa. The relatively higher risk of abscess following the 10-dose presentation of pentavalent vaccine merits further study. PMID:26509274

Cost of goods sold and total cost of delivery for oral and parenteral vaccine packaging formats.

Science.gov (United States)

Sedita, Jeff; Perrella, Stefanie; Morio, Matt; Berbari, Michael; Hsu, Jui-Shan; Saxon, Eugene; Jarrahian, Courtney; Rein-Weston, Annie; Zehrung, Darin

2018-03-14

Despite limitations of glass packaging for vaccines, the industry has been slow to implement alternative formats. Polymer containers may address many of these limitations, such as breakage and delamination. However, the ability of polymer containers to achieve cost of goods sold (COGS) and total cost of delivery (TCOD) competitive with that of glass containers is unclear, especially for cost-sensitive low- and lower-middle-income countries. COGS and TCOD models for oral and parenteral vaccine packaging formats were developed based on information from subject matter experts, published literature, and Kenya's comprehensive multiyear plan for immunization. Rotavirus and inactivated poliovirus vaccines (IPV) were used as representative examples of oral and parenteral vaccines, respectively. Packaging technologies evaluated included glass vials, blow-fill-seal (BFS) containers, preformed polymer containers, and compact prefilled auto-disable (CPAD) devices in both BFS and preformed formats. For oral vaccine packaging, BFS multi-monodose (MMD) ampoules were the least expensive format, with a COGS of $0.12 per dose. In comparison, oral single-dose glass vials had a COGS of $0.40. BFS MMD ampoules had the lowest TCOD of oral vaccine containers at $1.19 per dose delivered, and ten-dose glass vials had a TCOD of $1.61 per dose delivered. For parenteral vaccines, the lowest COGS was achieved with ten-dose glass vials at $0.22 per dose. In contrast, preformed CPAD devices had the highest COGS at $0.60 per dose. Ten-dose glass vials achieved the lowest TCOD of the parenteral vaccine formats at $1.56 per dose delivered. Of the polymer containers for parenteral vaccines, BFS MMD ampoules achieved the lowest TCOD at $1.89 per dose delivered, whereas preformed CPAD devices remained the most expensive format, at $2.25 per dose delivered. Given their potential to address the limitations of glass and reduce COGS and TCOD, polymer containers deserve further consideration as alternative

Bioassay for aquatic ecosystems review and classification; Rassegna dei principali test di ecotossicologia acquatica

Energy Technology Data Exchange (ETDEWEB)

Sanci, Antonella; Rosa, Silvia [ENEA, Centro Ricerche Casaccia, Rome (Italy). Dipt. Ambiente

1997-09-01

Bioassay play a crucial role in assessing the actual or potential impacts of anthropogenic agents on the natural environment. In this technical report, literature on bioassays for aquatic ecosystems has been reviewed and classified. Problems associated with the choice and application of bioassays are discussed.

Comparison of solid and liquid-phase bioassays using ecoscores to assess contaminated soils

Energy Technology Data Exchange (ETDEWEB)

Lors, Christine [Universite Lille Nord de France, 1bis rue Georges Lefevre, 59044 Lille Cedex (France); Ecole des Mines de Douai, LGCgE-MPE-GCE, 941 rue Charles-Bourseul, 59500 Douai (France); Centre National de Recherche sur les Sites et Sols Pollues, 930 Boulevard Lahure, BP 537, 59505 Douai Cedex (France); Ponge, Jean-Francois, E-mail: ponge@mnhn.fr [Museum National d' Histoire Naturelle, Departement Ecologie et Gestion de la Biodiversite, CNRS UMR 7179, 4 Avenue du Petit-Chateau, 91800 Brunoy (France); Martinez Aldaya, Maite [Museum National d' Histoire Naturelle, Departement Ecologie et Gestion de la Biodiversite, CNRS UMR 7179, 4 Avenue du Petit-Chateau, 91800 Brunoy (France); Damidot, Denis [Universite Lille Nord de France, 1bis rue Georges Lefevre, 59044 Lille Cedex (France); Ecole des Mines de Douai, LGCgE-MPE-GCE, 941 rue Charles-Bourseul, 59500 Douai (France)

2011-10-15

Bioassays on aqueous and solid phases of contaminated soils were compared, belonging to a wide array of trophic and response levels and using ecoscores for evaluating ecotoxicological and genotoxicological endpoints. The method was applied to four coke factory soils contaminated mainly with PAHs, but also to a lesser extent by heavy metals and cyanides. Aquatic bioassays do not differ from terrestrial bioassays when scaling soils according to toxicity but they are complementary from the viewpoint of ecological relevance. Both aquatic and terrestrial endpoints are strongly correlated with concentrations of 3-ring PAHs. This evaluation procedure allows us to propose a cost-effective battery which embraces a wide array of test organisms and response levels: it includes two rapid bioassays (Microtox) and springtail avoidance), a micronucleus test and three bioassays of a longer duration (algal growth, lettuce germination and springtail reproduction). This battery can be recommended for a cost-effective assessment of polluted/remediated soils. - Highlights: > Comparison of liquid- and solid-phase bioassays on contaminated soils, using ecoscores. > Complementarity of liquid- and solid-phase bioassays for the evaluation of environmental hazards. > Proposal for a restricted battery of 5 most sensitive tests. > Use of this restricted battery for a cost-effective assessment of polluted/remediated soils. - Aqueous and solid phases of contaminated soils give similar results in terms of toxicity but are complementary for the evaluation of environmental hazards by ecoscores.

Soil bioassays as tools for sludge compost quality assessment

International Nuclear Information System (INIS)

Domene, Xavier; Sola, Laura; Ramirez, Wilson; Alcaniz, Josep M.; Andres, Pilar

2011-01-01

Composting is a waste management technology that is becoming more widespread as a response to the increasing production of sewage sludge and the pressure for its reuse in soil. In this study, different bioassays (plant germination, earthworm survival, biomass and reproduction, and collembolan survival and reproduction) were assessed for their usefulness in the compost quality assessment. Compost samples, from two different composting plants, were taken along the composting process, which were characterized and submitted to bioassays (plant germination and collembolan and earthworm performance). Results from our study indicate that the noxious effects of some of the compost samples observed in bioassays are related to the low organic matter stability of composts and the enhanced release of decomposition endproducts, with the exception of earthworms, which are favored. Plant germination and collembolan reproduction inhibition was generally associated with uncomposted sludge, while earthworm total biomass and reproduction were enhanced by these materials. On the other hand, earthworm and collembolan survival were unaffected by the degree of composting of the wastes. However, this pattern was clear in one of the composting procedures assessed, but less in the other, where the release of decomposition endproducts was lower due to its higher stability, indicating the sensitivity and usefulness of bioassays for the quality assessment of composts.

Biomonitoring of cyanotoxins in two tropical reservoirs by cladoceran toxicity bioassays.

Science.gov (United States)

da S Ferrão-Filho, Aloysio; Soares, Maria Carolina S; de Freitas Magalhães, Valeria; Azevedo, Sandra M F O

2009-02-01

This study evaluates the potential for the use of cladocerans in biomonitoring of cyanobacterial toxins. Two zooplankton species (Daphnia gessneri and Moina micrura) were cultivated in the laboratory for use in acute (48 h) and chronic (10 days) bioassays. Water samples were collected from two reservoirs and diluted in mineral water at four concentrations. Survivorship in the acute bioassays was used to calculate LC50, and survivorship and fecundity in chronic bioassays were used to calculate the intrinsic population growth rate (r) and the EC50. Analysis of phytoplankton in the water samples from one reservoir revealed that cyanobacteria were the dominant group, represented by the genera Anabaena, Cylindrospermopsis, and Microcystis. Results of bioassays showed adverse effects including death, paralysis, and reduced population growth rate, generally proportional to the reservoir water concentration. These effects may be related to the presence of cyanobacteria toxins (microcystins or saxitoxins) in the water.

Establishment of a bioassay for the toxicity evaluation and quality control of Aconitum herbs

International Nuclear Information System (INIS)

Qin, Yi; Wang, Jia-bo; Zhao, Yan-ling; Shan, Li-mei; Li, Bao-cai; Fang, Fang; Jin, Cheng; Xiao, Xiao-he

2012-01-01

Highlights: ► A new bioassay was optimized to evaluate the toxicity of Aconitum herbs. ► Characterizing total toxicity is its unique advantage over chemical analysis methods. ► The application of this bioassay promotes the safe use of Aconitum herbs in clinic. - Abstract: Currently, no bioassay is available for evaluating the toxicity of Aconitum herbs, which are well known for their lethal cardiotoxicity and neurotoxicity. In this study, we established a bioassay to evaluate the toxicity of Aconitum herbs. Test sample and standard solutions were administered to rats by intravenous infusion to determine their minimum lethal doses (MLD). Toxic potency was calculated by comparing the MLD. The experimental conditions of the method were optimized and standardized to ensure the precision and reliability of the bioassay. The application of the standardized bioassay was then tested by analyzing 18 samples of Aconitum herbs. Additionally, three major toxic alkaloids (aconitine, mesaconitine, and hypaconitine) in Aconitum herbs were analyzed using a liquid chromatographic method, which is the current method of choice for evaluating the toxicity of Aconitum herbs. We found that for all Aconitum herbs, the total toxicity of the extract was greater than the toxicity of the three alkaloids. Therefore, these three alkaloids failed to account for the total toxicity of Aconitum herbs. Compared with individual chemical analysis methods, the chief advantage of the bioassay is that it characterizes the total toxicity of Aconitum herbs. An incorrect toxicity evaluation caused by quantitative analysis of the three alkaloids might be effectively avoided by performing this bioassay. This study revealed that the bioassay is a powerful method for the safety assessment of Aconitum herbs.

The limits of two-year bioassay exposure regimens for identifying chemical carcinogens.

Science.gov (United States)

Huff, James; Jacobson, Michael F; Davis, Devra Lee

2008-11-01

Chemical carcinogenesis bioassays in animals have long been recognized and accepted as valid predictors of potential cancer hazards to humans. Most rodent bioassays begin several weeks after birth and expose animals to chemicals or other substances, including workplace and environmental pollutants, for 2 years. New findings indicate the need to extend the timing and duration of exposures used in the rodent bioassay. In this Commentary, we propose that the sensitivity of chemical carcinogenesis bio-assays would be enhanced by exposing rodents beginning in utero and continuing for 30 months (130 weeks) or until their natural deaths at up to about 3 years. Studies of three chemicals of different structures and uses-aspartame, cadmium, and toluene-suggest that exposing experimental animals in utero and continuing exposure for 30 months or until their natural deaths increase the sensitivity of bioassays, avoid false-negative results, and strengthen the value and validity of results for regulatory agencies. Government agencies, drug companies, and the chemical industry should conduct and compare the results of 2-year bioassays of known carcinogens or chemicals for which there is equivocal evidence of carcinogenicity with longer-term studies, with and without in utero exposure. If studies longer than 2 years and/or with in utero exposure are found to better identify potential human carcinogens, then regulatory agencies should promptly revise their testing guidelines, which were established in the 1960s and early 1970s. Changing the timing and dosing of the animal bioassay would enhance protection of workers and consumers who are exposed to potentially dangerous workplace or home contaminants, pollutants, drugs, food additives, and other chemicals throughout their lives.

PROPUESTA DE PROCEDIMIENTOS DE AUTOCONTROL EN CONTRATOS DE CONSERVACIÓN DE UNA RED VIAL

Directory of Open Access Journals (Sweden)

R. F. Herrera

2016-12-01

Full Text Available Con un contrato global mixto se lleva a cabo la mantención de una red vial, a través de la ejecución simultánea de conservación bajo la modalidad a serie de precios unitarios, y bajo suma alzada por nivel de servicio. En estos últimos se evidencia una mayor precariedad en los procedimientos, debido a fallas en la visión de la empresa contratista en asumir la gestión de la conservación, carencia en la asignación de responsabilidades a los miembros del equipo, y el deficiente control de la calidad de las obras y documentación del contrato. Por este motivo, en este trabajo se realiza una propuesta de gestión definiendo cada una de las etapas que la componen, con la finalidad de asegurar una correcta conservación de los elementos que conforman la infraestructura vial. Los objetivos propuestos son: especificar la metodología a usar para gestionar la mantención de la red contratada bajo la modalidad global mixto, especificar el manejo y control de la documentación que deben mantener en el contrato, y definir las aptitudes y responsabilidades del equipo de trabajo. Para cumplir con los mismos se realizó una revisión bibliográfica de la normativa nacional acerca de la mantención de caminos, y se tomó conocimiento de la diversidad de contratos que utiliza la Dirección de Vialidad para la conservación vial. Además, a través de la experiencia en contratos de conservación global mixto se definen las aptitudes y responsabilidades que se recomienda que tengan los miembros del equipo de trabajo.

Are bioassays useful tools to assess redox processes and biodegradation?

DEFF Research Database (Denmark)

Albrechtsen, Hans-Jørgen; Pedersen, Philip Grinder; Ludvigsen, L.

2002-01-01

sensitive hydrochemical or geochemical parameters, levels of hydrogen, and redox potential. However, all these approaches have to be evaluated against TEAP-bioassays as the most direct measure. We assessed successfully ongoing microbial-mediated redox processes by TEAP-bioassays in degradation studies...... of aromatic and chlorinated aliphatic compounds in landfill leachate plumes, and of pesticides in aquifers with various redox conditions....

Comparison of solid and liquid-phase bioassays using ecoscores to assess contaminated soils

International Nuclear Information System (INIS)

Lors, Christine; Ponge, Jean-Francois; Martinez Aldaya, Maite; Damidot, Denis

2011-01-01

Bioassays on aqueous and solid phases of contaminated soils were compared, belonging to a wide array of trophic and response levels and using ecoscores for evaluating ecotoxicological and genotoxicological endpoints. The method was applied to four coke factory soils contaminated mainly with PAHs, but also to a lesser extent by heavy metals and cyanides. Aquatic bioassays do not differ from terrestrial bioassays when scaling soils according to toxicity but they are complementary from the viewpoint of ecological relevance. Both aquatic and terrestrial endpoints are strongly correlated with concentrations of 3-ring PAHs. This evaluation procedure allows us to propose a cost-effective battery which embraces a wide array of test organisms and response levels: it includes two rapid bioassays (Microtox) and springtail avoidance), a micronucleus test and three bioassays of a longer duration (algal growth, lettuce germination and springtail reproduction). This battery can be recommended for a cost-effective assessment of polluted/remediated soils. - Highlights: → Comparison of liquid- and solid-phase bioassays on contaminated soils, using ecoscores. → Complementarity of liquid- and solid-phase bioassays for the evaluation of environmental hazards. → Proposal for a restricted battery of 5 most sensitive tests. → Use of this restricted battery for a cost-effective assessment of polluted/remediated soils. - Aqueous and solid phases of contaminated soils give similar results in terms of toxicity but are complementary for the evaluation of environmental hazards by ecoscores.

Paper-based chromatic toxicity bioassay by analysis of bacterial ferricyanide reduction.

Science.gov (United States)

Pujol-Vila, F; Vigués, N; Guerrero-Navarro, A; Jiménez, S; Gómez, D; Fernández, M; Bori, J; Vallès, B; Riva, M C; Muñoz-Berbel, X; Mas, J

2016-03-03

Water quality assessment requires a continuous and strict analysis of samples to guarantee compliance with established standards. Nowadays, the increasing number of pollutants and their synergistic effects lead to the development general toxicity bioassays capable to analyse water pollution as a whole. Current general toxicity methods, e.g. Microtox(®), rely on long operation protocols, the use of complex and expensive instrumentation and sample pre-treatment, which should be transported to the laboratory for analysis. These requirements delay sample analysis and hence, the response to avoid an environmental catastrophe. In an attempt to solve it, a fast (15 min) and low-cost toxicity bioassay based on the chromatic changes associated to bacterial ferricyanide reduction is here presented. E. coli cells (used as model bacteria) were stably trapped on low-cost paper matrices (cellulose-based paper discs, PDs) and remained viable for long times (1 month at -20 °C). Apart from bacterial carrier, paper matrices also acted as a fluidic element, allowing fluid management without the need of external pumps. Bioassay evaluation was performed using copper as model toxic agent. Chromatic changes associated to bacterial ferricyanide reduction were determined by three different transduction methods, i.e. (i) optical reflectometry (as reference method), (ii) image analysis and (iii) visual inspection. In all cases, bioassay results (in terms of half maximal effective concentrations, EC50) were in agreement with already reported data, confirming the good performance of the bioassay. The validation of the bioassay was performed by analysis of real samples from natural sources, which were analysed and compared with a reference method (i.e. Microtox). Obtained results showed agreement for about 70% of toxic samples and 80% of non-toxic samples, which may validate the use of this simple and quick protocol in the determination of general toxicity. The minimum instrumentation

Comparative evaluation of fluoride release and recharge of pre-reacted glass ionomer composite and nano-ionomeric glass ionomer with daily fluoride exposure: An in vitro study

Directory of Open Access Journals (Sweden)

Jayanthi Mungara

2013-01-01

Full Text Available Aim: This in vitro study was designed to investigate the effects of daily fluoride exposures on fluoride release and recharge by prereacted glass ionomer (PRG composite and nano-ionomeric glass ionomer. Materials and Methods: Seventy-two specimens (36 of each material were prepared and by placing the restorative materials into Teflon mold. Each specimen was subjected to one of three daily treatments (n = 12: (1 No fluoride treatment (control; (2 application of a fluoride dentifrice (1,000 ppm once daily; and (3 the same regimen as (2, plus immersion in a 0.05% sodium fluoride (NaF mouth rinse (225 ppm immediately following the dentifrice application. Specimens were suspended in a storage vial containing 10 ml demineralizing solution for 6 h and transferred to a new test tube containing 10 ml remineralizing solution for 18 h. Fluoride treatments of the specimens were completed every day prior to their immersion in the demineralizing solution. Media solutions were buffered with equal volumes of total ionic strength adjustment buffer (TISAB II; fluoride levels were measured using a digital ion analyzer and fluoride electrode throughout the 21 day duration of the experiment. Results: Nano-ionomeric glass ionomer showed a better amount of fluoride release than PRG composite irrespective of the fluoride treatment supplementation (P < 0.01. Additional fluoride supplementation improved fluoride release and recharge ability for both the materials when compared to their respective control groups. The fluoride recharge for both materials did not show any sustained pattern of release. Conclusion: Nano-ionomeric glass ionomer demonstrated a greater ability to release and recharge compared with that of PRG composite.

Measurement of low-level beta activity of samples in liquid state using plastic scintillator vials

International Nuclear Information System (INIS)

Wezranowski, E.; Panczyk, E.; Radwan, M.

1977-01-01

Plastic scintillation vials having walls from a plastic scintillator and the bottom from perspex were used. Wall thickness was 0.8 to 3 mm. The solution radioactivity was measured by a scintillation beta spectrometer. The total measurement errors were found for the following radionuclides: 14 C +-3.7%; 204 Tl +-3%; 32 P +-2.8%; 137 Cs +-2%, and 72 Ga +-5%. Detection efficiency was found to decrease rapidly with the solution layer thickness. For a solution thickness of 0.2 mm the highest detection efficiency was observed with the 4% measurement error. Linear dependence was found of detection efficiency on beta energy. For a solution layer thickness of 0.2 mm the minimum measurable activities were determined to be 30.3 pCi for 14 C and 2.12 pCi for 32 P. The use of the above vials permits quick and simple measurement without sample chemical preparation. (J.P.)

Improvements in and environmental applications of double-vial radiorespirometry for the study of microbial mineralization

International Nuclear Information System (INIS)

McKinley, V.L.; Federle, T.W.; Vestal, J.R.

1983-01-01

Several variations in the scintillation mixture and the filter paper arrangements for double-vial radiorespirometry were compared. Improved efficiencies (44%) and shorter response times were found by adding wetting agents and methanotic NaOH to the scintillation mixture in the filter paper. The scintillation chemicals used did not contain dioxane and were found to be nontoxic to the test microbiota in this system. Covering the inner reaction vial with aluminum foil minimized the reduction in counting efficiency when testing colored or dense environmenal samples. Mineralization rates were determined with 14 C-labeled glucose, acetate, and glutamate and [ 14 C]cellulose- and [ 14 C]lignin-labeled lignocellulose for composting cow manure, forest soil, and arctic lake sediment microbiota. This improved method can be used in a variety of procedures involving the measurement of microbial mineralizations of organic compounds. Since no liquid scintillation cocktail is used for counting, the radioactive wastes are aqueous or can be incinerated, making disposal easy

Influência do tamanho do frasco de tuberculina nos resultados da prova tuberculínica Influence of vial size on the results of the tuberculin test

Directory of Open Access Journals (Sweden)

Antonio Ruffino-Netto

2005-04-01

Full Text Available INTRODUÇÃO: A solução de tuberculina é armazenada em frascos de diferentes tamanhos. Sua adsorção ao frasco pode influenciar o resultado da prova tuberculínica. OBJETIVO: Avaliar o efeito do tamanho do frasco de armazenamento da tuberculina nos resultados obtidos na prova tuberculínica. MÉTODO: Sessenta e três pacientes internados com diagnóstico de tuberculose ativa foram submetidos a duas provas tuberculínicas simultâneas, em ambos os antebraços. A técnica usada foi a de Mantoux e consistiu na aplicação de 0,1 ml de tuberculina armazenada em frascos de 5 ml ou de 1,5 ml, no antebraço direito e no antebraço esquerdo, de forma aleatória. A leitura da induração foi efetuada de forma cega por um único leitor treinado previamente. As leituras com diferenças de até 2 mm foram consideradas resultados concordantes. RESULTADOS: Vinte e um pacientes não tiveram induração e foram excluídos da análise. Entre os 42 pacientes restantes, a média dos diâmetros das indurações obtidas nas provas com tuberculina armazenada nos frascos grandes foi maior do que as obtidas com a armazenada em frascos pequenos. A concordância entre as leituras foi obtida em 40,5% delas (17/42, e a diferença foi negativa (frasco grande menor que frasco pequeno em 16,7% (7/42 e positiva em 42,9% delas (18/42. CONCLUSÃO: O tamanho do frasco de armazenamento da tuberculina pode influenciar o resultado da prova tuberculínica. A adsorção da tuberculina à parede do frasco pode explicar o fenômeno. Os autores alertam para o impacto dessas variações nos estudos epidemiológicos e operacionais.BACKGROUND: Tuberculin purified protein derivative is stored in vials of various sizes. Its adsorption to the vial can influence the results of tuberculin tests. OBJECTIVE: To evaluate the effect of vial size on the results obtained in tuberculin tests. METHODS: Sixty-four inpatients with active tuberculosis were submitted to two simultaneous tuberculin tests

Liquid scintillation vial for radiometric assay of lymphocyte carbohydrate metabolism in response to mitogens

International Nuclear Information System (INIS)

Tran, N.; Wagner, H.N. Jr.

1978-01-01

We have demonstrated that mitogens--i.e., PHA and Con.A--stimulate lymphocyte carbohydrate metabolism using a liquid-scintillation vial with conventional liquid-scintillation detectors. The results showed that this enclosed system can be useful for development of rapid in vitro tests of lymphocytes immune responsiveness, as well as for radiometric detection of bacterial growth in various gaseous atmospheres

Manual on theory and practical aspects of bioassay

International Nuclear Information System (INIS)

Nuraini Hambali.

1985-06-01

This manual is set to provide necessary basic guidance on theory and practical aspects of bioassay specially for the newcomer in this field and the man in the laboratory. The first part is a brief information on the entry of radionuclides into the body, the metabolism and the programs of bioassay. All other factors to be considered in assessing internal contamination in man have also been brought up. In the second part, various procedures of radiochemical separations, detection and measurements are abstracted from journals and other revisions. Some methods have been attempted and to be followed where appropriate. (author)

Exposure dose assessment using bioassay

International Nuclear Information System (INIS)

Suga, Shinichi

1994-01-01

Bioassay involves following steps: sampling, pre-treatment, chemical separation and counting of radioactivity. As bioassay samples, urines are usually used, although faecal analysis may be required in some occasions for example to assess intake of non-transferable radioactive materials. Nasal smear is a useful indicator of an inhalation case. Exhalation air is used to estimate the intake of tritiated water. Sample pre-treatment includes evaporation for concentration, wet ashing, dry ashing and co-precipitation. After adding small amount of nitric acid, the sample can be concentrated by 1/10 of initial volume, which may be used to identify γ-emitters. As the pre-treatment of urine, wet ashing is used for example for analysis of Pu, and co-precipitation is used for example for analysis of Sr. Dry ashing by electric furnace is usually adopted for faecal samples. Methods of chemical separation depend on the radionuclide(s) to be analysed. The detection limit depends also on radionuclide, and for example typical detection limits are 0.4Bq / l (volume of urine sample) for 89 Sr or 90 Sr, and 0.01 Bq / l with urine and 0.01 Bq per sample with faeces for 238 Pu, 239 Pu or 241 Am. Simpler methods can be used for some radionuclides: For example, radioactivity concentration of tritium can be determined by liquid scintillation counting of urine or condensed water from exhaled air, and natural uranium in urine can be quantified by using fluorometric method. In some circumstances, gross-α or gross-β analyses are useful for quick estimation. To estimate intakes by inhalation or by ingestion from bioassay results and to assess the committed dose equivalent, commonly available bases are the relevant publications by the ICRP and domestic guides and manuals that conform to the radiation protection regulations. (author)

Review of literature on bioassay methods for estimating radionuclides in urine

International Nuclear Information System (INIS)

Prasad, M.V.R.; Surya Narayana, D.S.; Jeevanram, R.K.; Sundarajan, A.R.

1991-01-01

Bioassay methods of certain important radionuclides encountered in the nuclear fuel cycle operations, viz., thorium, uranium, sup(239)Pu, sup(241)Am, sup(90)Sr, sup(99)Tc, sup(106)Ru, sup(137)Cs are reviewed, with special emphasis on urinalysis. Since the preconcentration is an important prerequisite for bioassay, various preconcentration methods are also discussed. Brief account of various instruments both nuclear and analytical used in the bioassay programme is included. The sensitivities of the methods cited in the literature vis-a-vis the derived recording levels indicated in ICRP recommendations are compared. Literature surveyed up to 1990 is tabulated. (author). 96 refs., 1 fig ., 3 tabs

Storing of Extracts in Polypropylene Microcentrifuge Tubes Yields Contaminant Peak During Ultra-flow Liquid Chromatographic Analysis

OpenAIRE

Kshirsagar, Parthraj R.; Hegde, Harsha; Pai, Sandeep R.

2016-01-01

Background and Aim: This study was designed to understand the effect of storage in polypropylene microcentrifuge tubes and glass vials during ultra-flow liquid chromatographic (UFLC) analysis. Materials and Methods: One ml of methanol was placed in polypropylene microcentrifuge tubes (PP material, Autoclavable) and glass vials (Borosilicate) separately for 1, 2, 4, 8, 10, 20, 40, and 80 days intervals stored at ?4?C. Results: Contaminant peak was detected in methanol stored in polypropylene m...

Sample loading for C-14 measurement in the simulated organic solvent waste from a CANDU Nuclear Power Plant

International Nuclear Information System (INIS)

Dianu, Magdalena; Podina, C.; Nita, Valentina

2005-01-01

Full text: Sample preparation is a critical step in obtaining accurate results in scintillation counting. Standard (22 ml) glass and plastic vials were used in these experiments. The preliminary research was conducted using glass vials to allow visual verification that a homogeneous solution is obtained at the desired cocktail/sample ratio. Then, the research was moved into plastic vials to reduce backgrounds and improve the counting rate. Samples were counted in a Model 2100 TR Packard TRI-CARB liquid scintillation analyzer. The paper mainly contains: - Composition and data about liquid scintillation cocktails used (tables); - Characterization of radioactive waste - organic solvent contaminated with C-14; - Sample loading (tables); - Efficiency vs Sample Loading - for each cocktail used. Organic solvent sample volumes were added to the vials in 0.5 ml increments from 1 ml to 2 ml. Then, the liquid scintillation cocktail was added so that the sample-cocktail volume was 20 ml. Each vial was shaken vigorously for several seconds after each addition to ensure homogeneity and count. Blank vials were prepared using C-14-free organic solvent samples in the same sample-cocktail proportions. After at least two hours, the samples and blank vials were counted for ten minutes, using a Packard counter. (authors)

Worldwide bioassay data resources for plutonium/americium internal dosimetry studies

International Nuclear Information System (INIS)

Miller, G.; Bertelli, L.; Little, T.; Guilmette, R.; Riddell, T.; Filipy, R.

2005-01-01

Full text: Biokinetic models are the scientific underpinning of internal dosimetry. These models describe how materials of interest taken into the body by various routes (for example inhalation) are transported through the body, allowing the modelling of bioassay measurements and the estimation of radiation dose. The International Commission on Radiation Protection (ICRP) publishes biokinetic models for use in internal dosimetry. These models represent the consensus judgement of a committee of experts, based on human and animal data. Nonetheless, it is important to validate biokinetic models using directly applicable data, in a scientifically transparent manner, especially for internal dosimetry research purposes (as opposed to radiation protection), as in epidemiology studies. Two major goals would be to determine individual variations of model parameters for the purpose of assessing this source of uncertainty in internal dose calculations, and to determine values of workplace specific parameters (such as particle solubility in lung fluids) for different representative workplaces. Furthermore, data on the observed frequency of intakes under various conditions can be used in the interpretation of bioassay data. All of the above may be couched in the terminology of Bayesian statistical analysis and amount to the determination of the Bayesian prior probability distributions needed in a Bayesian interpretation of bioassay data. The authors have direct knowledge of several significant databases of plutonium/americium bioassay data (including autopsy data). The purpose of this paper is to acquaint the worldwide community with these resources and to invite others who may know of other such databases to participate with us in a publication that would document the content, form, and the procedures for seeking access to these databases. These databases represent a tremendous scientific resource in this field. Examples of databases known to the authors include: the

Paper-based microfluidics with high resolution, cut on a glass fiber membrane for bioassays.

Science.gov (United States)

Fang, Xueen; Wei, Shasha; Kong, Jilie

2014-03-07

In this report, we describe a simple, low-cost, straight forward and highly reproducible fabrication method of microfluidic systems. This system was cut on a glass fiber membrane by a common cutter without using any other sophisticated equipment or organic solvents. This format represents a novel type of paper-based microfluidics with high resolution of the microchannel down to ~137 μm, comparable to those made by conventional photolithography. We successfully applied this method to microfluidics to create a star micro-array format of multiplexed urine tests in this study.

Avaliação da influência de microfissuras superficiais em frascos de vidro tipo I para produtos farmacêuticos

Directory of Open Access Journals (Sweden)

SANDRA BALAN MENDOZA JAIME

2011-06-01

Full Text Available O objetivo deste estudo foi caracterizar e verificar a influência de microfissuras na manutenção da esterilidade e do desempenho mecânico de frascos de vidro tipo I, de 4 mL e 13 mL (terminação 13 mm para produtos esterilizáveis e de 7 mL (terminação 20 mm para produtos liofilizados, após acondicionamento em linha e simulação de transporte. Microfissuras superficiais em frascos de vidro tipo I podem ser formadas devido ao contato entre o vidro e o ferramental, associado a variações na intensidade da chama, durante o processo produtivo da embalagem. Verificou-se que a tensão residual da embalagem não é alterada pela presença das microfissuras e que os sistemas de fechamento apresentam adequada integridade e propriedades de barreira à umidade. Mesmo com microfissuras superficiais, a manutenção da esterilidade do produto simulante, acondicionado nos frascos esterilizados (4 mL e 13 mL, não apresentaram alteração após o envase em linha e simulação de transporte. No caso do frasco de 7 mL, as microfissuras podem ter contribuído para a ocorrência de alteração de 1% do total das embalagens após o processo de liofilização. Uma maior incidência de quebra por carga vertical, localizada na região do ombro/terminação, foi observada devido à presença das microfissuras. O desempenho mecânico e térmico dos frascos estudados, contudo, não foi alterado pela presença das microfissuras. Palavras-chave: Frascos de vidro tipo I. Produtos farmacêuticos. Microfissuras superficiais. ABSTRACT Assessment of the influence of microcracks in type 1 glass vials for pharmaceutical products The objective of this study was to ascertain the influence of microcracks on the maintenance of sterility and mechanical performance of type 1 (i.e. borosilicate glass vials, of 4 mL and 13 mL (neck 13 mm for sterile pharmaceutical products and 7 mL (neck 20 mm for freeze-dried products, after in-line filling and transport simulation. Microcracks

[Application of bioassay in quality control of Chinese materia medica-taking Radix Isatidis as an example].

Science.gov (United States)

Yan, Dan; Ren, Yongshen; Luo, Jiaoyang; Li, Hanbing; Feng, Xue; Xiao, Xiaohe

2010-10-01

Bioassay, which construct the characteristics consistents with Chinese medical science, is the core mode and methods for the quality control of Chinese materia medica. Taking the bioassay of Radix Isatidis as an example, the contribution, status and application of bioassay in the quality control of Chinese materia medica were introduced in this article, and two key issue (the selection of reference and measurement methods) in the process of establishing bioassay were also explained. This article expects to provide a reference for the development and improvement of the bioassay of Chinese materia medica in a practical manipulation level.

Cell-patterned glass spray for direct drug assay using mass spectrometry

International Nuclear Information System (INIS)

Wu, Jing; Wang, Shiqi; Chen, Qiushui; Jiang, Hao; Liang, Shuping; Lin, Jin-Ming

2015-01-01

In this work, the establishment of a glass spray mass spectrometry (GS-MS) platform for direct cell-based drug assay was described. Cell co-culture, drug-induced cell apoptosis, proliferation analysis and intracellular drug absorption measurement were performed simultaneously on this specifically designed platform. Two groups of co-cultured cells (NIH-3T3/HepG2 and HepG2/MCF-7) were cultivated and they showed high viability within 3 days. The biocompatibility of the platform facilitated the subsequent bioassays, in which, cyclophosphamide (CPA) and genistein were used as the model drugs. The distinctions of cell apoptosis and proliferation between the mono-cultured and co-cultured cells were clearly observed and well explained by in situ GS-MS measurements. A satisfactory linearity of the calibration curve between the relative MS intensity and CPA concentrations was obtained using stable isotope labeling method (y = 0.16545 + 0.0985x, R"2 = 0.9937). The variations in the quantity of absorbed drug were detected and the results were consistent with the concentration-dependence of cell apoptosis. All the results demonstrated that direct cell-based drug assay could be performed on the stable isotope labeling assisted GS-MS platform in a facile and quantitative manner. - Highlights: • A versatile glass spray mass spectrometry (GS-MS) platform for direct cell-based drug assay was developed in this paper. • It has characteristics of the atmospheric pressure ionization method. • It is multifunctional for cell co-culture, bioassays, qualitative and quantitative intracellular drug absorption measurement. • GS-MS has the potential to increase the use of mass spectrometry in biological analysis.

In vitro bioassays to evaluate complex chemical mixtures in recycled water

Science.gov (United States)

Jia, Ai; Escher, Beate I.; Leusch, Frederic D.L.; Tang, Janet Y.M.; Prochazka, Erik; Dong, Bingfeng; Snyder, Erin M.; Snyder, Shane A.

2016-01-01

With burgeoning population and diminishing availability of freshwater resources, the world continues to expand the use of alternative water resources for drinking, and the quality of these sources has been a great concern for the public as well as public health professionals. In vitro bioassays are increasingly being used to enable rapid, relatively inexpensive toxicity screening that can be used in conjunction with analytical chemistry data to evaluate water quality and the effectiveness of water treatment. In this study, a comprehensive bioassay battery consisting of 36 bioassays covering 18 biological endpoints was applied to screen the bioactivity of waters of varying qualities with parallel treatments. Samples include wastewater effluent, ultraviolet light (UV) and/or ozone advanced oxidation processed (AOP) recycled water, and infiltrated recycled groundwater. Based on assay sensitivity and detection frequency in the samples, several endpoints were highlighted in the battery, including assays for genotoxicity, mutagenicity, estrogenic activity, glucocorticoid activity, aryl hydrocarbon receptor activity, oxidative stress response, and cytotoxicity. Attenuation of bioactivity was found to be dependent on the treatment process and bioassay endpoint. For instance, ozone technology significantly removed oxidative stress activity, while UV based technologies were most efficient for the attenuation of glucocorticoid activity. Chlorination partially attenuated genotoxicity and greatly decreased herbicidal activity, while groundwater infiltration efficiently attenuated most of the evaluated bioactivity with the exception of genotoxicity. In some cases, bioactivity (e.g., mutagenicity, genotoxicity, and arylhydrocarbon receptor) increased following water treatment, indicating that transformation products of water treatment may be a concern. Furthermore, several types of bioassays with the same endpoint were compared in this study, which could help guide the selection

Enhanced low-level LSC performance for carbon-14 dating using a bismuth germanate (Bi4Ge3O12) quasi-active guard

International Nuclear Information System (INIS)

Cook, G.T.

1995-01-01

The Packard 2770TR/SL is a novel low-level liquid scintillation spectrometer which employs bismuth germanate (BGO - Bi 4 Ge 3 O 12 ) as a quasi-active guard to reduce background count rates and improve limits of detection. The results of this study indicate that this system shows tremendous potential for radiocarbon dating. Its great advantage is that it can give exceptional performance using standard low 40 K borosilicate glass vials costing only a few cents each. For example, in an optimized counting window, 4.6-mL 14 C benzene contained in a standard 7-mL glass vial produced a background count rate of 0.49 cpm and an efficiency of 70.3%, yielding a figure of merit (E 2 V 2 /B) value of 213,000 ±9,000 (where B = background count rate in counts per minute [cpm], E = percentage efficiency, and V = volume of benzene). This performance is comparable to published data for low-level instruments which employ active coincidence guard detectors and standard glass vials. When the same vials were recounted in vial holders, specially fabricated from BGO, the corresponding optimum values for background, efficiency and figure of merit, respectively, were 0.24 cpm, 61.0% and 328,000 ± 19,000. This performance is comparable to that of other low-level counting instruments when they are used in combination with specialized Teflon and silica vials. The BGO vial holders were also used in previous generations of Packard instruments which employ time resolved liquid scintillation counting (TR-LSC) for electronic background reduction and this resulted in significant improvements in performance

US Army Radiological Bioassay and Dosimetry: The RBD software package

International Nuclear Information System (INIS)

Eckerman, K.F.; Ward, R.C.; Maddox, L.B.

1993-01-01

The RBD (Radiological Bioassay and Dosimetry) software package was developed for the U. S. Army Material Command, Arlington, Virginia, to demonstrate compliance with the radiation protection guidance 10 CFR Part 20 (ref. 1). Designed to be run interactively on an IBM-compatible personal computer, RBD consists of a data base module to manage bioassay data and a computational module that incorporates algorithms for estimating radionuclide intake from either acute or chronic exposures based on measurement of the worker's rate of excretion of the radionuclide or the retained activity in the body. In estimating the intake,RBD uses a separate file for each radionuclide containing parametric representations of the retention and excretion functions. These files also contain dose-per-unit-intake coefficients used to compute the committed dose equivalent. For a given nuclide, if measurements exist for more than one type of assay, an auxiliary module, REPORT, estimates the intake by applying weights assigned in the nuclide file for each assay. Bioassay data and computed results (estimates of intake and committed dose equivalent) are stored in separate data bases, and the bioassay measurements used to compute a given result can be identified. The REPORT module creates a file containing committed effective dose equivalent for each individual that can be combined with the individual's external exposure

Standardization of a fluconazole bioassay and correlation of results with those obtained by high-pressure liquid chromatography.

Science.gov (United States)

Rex, J H; Hanson, L H; Amantea, M A; Stevens, D A; Bennett, J E

1991-01-01

An improved bioassay for fluconazole was developed. This assay is sensitive in the clinically relevant range (2 to 40 micrograms/ml) and analyzes plasma, serum, and cerebrospinal fluid specimens; bioassay results correlate with results obtained by high-pressure liquid chromatography (HPLC). Bioassay and HPLC analyses of spiked plasma, serum, and cerebrospinal fluid samples (run as unknowns) gave good agreement with expected values. Analysis of specimens from patients gave equivalent results by both HPLC and bioassay. HPLC had a lower within-run coefficient of variation (less than 2.5% for HPLC versus less than 11% for bioassay) and a lower between-run coefficient of variation (less than 5% versus less than 12% for bioassay) and was more sensitive (lower limit of detection, 0.1 micrograms/ml [versus 2 micrograms/ml for bioassay]). The bioassay is, however, sufficiently accurate and sensitive for clinical specimens, and its relative simplicity, low sample volume requirement, and low equipment cost should make it the technique of choice for analysis of routine clinical specimens. PMID:1854166

BioAssay templates for the semantic web

Directory of Open Access Journals (Sweden)

Alex M. Clark

2016-05-01

Full Text Available Annotation of bioassay protocols using semantic web vocabulary is a way to make experiment descriptions machine-readable. Protocols are communicated using concise scientific English, which precludes most kinds of analysis by software algorithms. Given the availability of a sufficiently expressive ontology, some or all of the pertinent information can be captured by asserting a series of facts, expressed as semantic web triples (subject, predicate, object. With appropriate annotation, assays can be searched, clustered, tagged and evaluated in a multitude of ways, analogous to other segments of drug discovery informatics. The BioAssay Ontology (BAO has been previously designed for this express purpose, and provides a layered hierarchy of meaningful terms which can be linked to. Currently the biggest challenge is the issue of content creation: scientists cannot be expected to use the BAO effectively without having access to software tools that make it straightforward to use the vocabulary in a canonical way. We have sought to remove this barrier by: (1 defining a BioAssay Template (BAT data model; (2 creating a software tool for experts to create or modify templates to suit their needs; and (3 designing a common assay template (CAT to leverage the most value from the BAO terms. The CAT was carefully assembled by biologists in order to find a balance between the maximum amount of information captured vs. low degrees of freedom in order to keep the user experience as simple as possible. The data format that we use for describing templates and corresponding annotations is the native format of the semantic web (RDF triples, and we demonstrate some of the ways that generated content can be meaningfully queried using the SPARQL language. We have made all of these materials available as open source (http://github.com/cdd/bioassay-template, in order to encourage community input and use within diverse projects, including but not limited to our own

Application of Bioassays for the Ecotoxicity Assessment of Contaminated Soils

Science.gov (United States)

Fernández, María D.; Babín, Mar; Tarazona, José V.

The use of bioassays for soil characterization is receiving significant attention as a complementary tool to chemical analysis. Bioassays consist of direct toxicity assays of environmental samples that are transferred to the laboratory and analyzed for toxicity against selected organisms. Such soil samples contain the combination of the different pollutants present in situ and enable factors such as the bioavailability of contaminants or the interactions (synergic and antagonic) between them to be simultaneously studied.

7 Vascular Hydrophytes for Bioassay.cdr

African Journals Online (AJOL)

Administrator

4 water (see Table 1). tool. The greater extension growth of macrophyte shoots in water from downstream of STWs (Fig. 1) was supported by both chemical analysis, which showed increased phosphate concentration (Table 1), and by conventional Selenastrum bioassay in which higher cell concentrations were achieved.

Do insulin cartridges really provide a lower risk of potential diabetes complications than traditional vials?

Science.gov (United States)

Al-Sharayri, Mohammad G; Aljbori, Tariq M; Migdadi, Qusai M; Al-Omoush, Marwa B; Jaarah, Ayman R

2014-09-01

Recently, many publicly funded healthcare organizations suffered from an economical crisis. This forced some organizations to utilize less costly alternatives where possible. Insulin cartridges and vials are examples. Many patients are questioning the difference between the two alternatives as they contain the same active ingredient. To find out if insulin cartridges really provide a lower risk of potential diabetes complications than traditional vials. A questionnaire was used to ask two random samples of diabetic patients about the development of some diabetes complications. The first sample (n = 41) consisted of patients using cartridges; the second sample (n = 40) consisted of patients using vials. Patients were randomly selected from the endocrine clinic and the out-patient pharmacy in Al-Hussein Hospital in King Hussein Medical Center in Amman- Jordan. 44% of respondents in the first sample did not suffer from any complication; on the other hand, the percentage was only 15% of respondents in the second sample. All respondents (100%) in the first sample suffered from only 2 complications or less; however, 25% of the respondents in the second sample suffered from 3 or more complications. Nephropathy complications, were slightly higher in the first sample; 22% compared to 15% in the second sample. On the other hand, all complications reported in the second sample were higher; 30% for neuropathy, 65% for retinopathy complications and 42.5% for extremities damage compared to only 9.7%, 7.3% and 26.8% respectively in the first sample. In general, respondents who were using cartridges reported a lesser incidence of diabetes complications. Although many organizations suffered from an economical crisis, the cost-effectiveness aspect should be taken into consideration when purchasing medical alternatives. This will provide higher quality of life for patients and eventually lower hidden and future costs for the organizations.

Bioassay-based risk assessment of hazardous waste

Energy Technology Data Exchange (ETDEWEB)

Donnelly, K.C.; Brown, K.W.; He, L.Y. [Texas A and M Univ., College Station, TX (United States)

1994-12-31

Microbial bioassays have been used to assess the genotoxic hazard at more than 30 different hazardous waste sites. Environmental samples were extracted with dichloromethane and methanol, and the resulting residue tested using GC/MS analysis as well as the Salmonella Microsomal and E. coli Prophage Induction assays. At a munitions wastewater contaminated site, there was no correlation between mutagenicity in bacteria, and the risk as estimated from chemical analysis data of trinitrotoluene. Samples 202 and 204 from a coal gasification site contained 72 mg/kg and 9 mg/kg benzo(a)pyrene, whereas the mutagenic responses of these samples were 231 net revertants/mg and 902 revertants/mg, respectively. The data suggest that microbial bioassays provide a valuable tool for monitoring the interactions of the components of a complex mixture.

Comparative analysis of ampoules and vials in sterile and conventional packaging as to microbial load and sterility test.

Science.gov (United States)

Freitas, Raphael Ribeiro de Aquino; Tardelli, Maria Angela

2016-05-24

To compare sterility and microbial (bacteria and fungi) load in the outer part of hyperbaric bupivacaine (Neocaína®) in ampoule and bupivacaine in vial, in conventional and sterile pack formulations. The sterile packs were divided into two groups: G1 (n=16) with ampoules and G2 (n=16) with vials. Conventional formulations were divided into two groups, being G3 (n=16) with ampoules and G4 (n=16) with vials. The ampoules and vials were opened and had their content drawn. The empty bottles were then placed in sterile plastic bags and sent for analysis of microbial load (bacteria and fungi) and sterility testing. Data were analyzed using the χ2 test with Yates correction, and 95% confidence interval. G1 and G2 showed no bacterial growth when compared to conventional groups (pgrupos, sendo que o G1 (n=16) continha as ampolas e o G2 (n=16), os frascos-ampola. As apresentações convencionais foram distribuídas em dois grupos, a saber G3 (n=16) com as ampolas e G4 (n=16) com os frascos-ampola. As ampolas e os frascos-ampolas eram abertos e tinham seu conteúdo aspirado. Os frascos vazios eram, então, acondicionados em sacos plásticos estéreis e enviados para análise quanto à carga microbiana (bactérias e fungos), bem como para o teste de esterilidade. Os dados foram analisados por meio do teste χ2 com correção Yates com intervalo de confiança de 95%. Os grupos G1 e G2 não apresentaram crescimento bacteriano quando comparado aos grupos convencionais (pgrupos. O uso de embalagens estéreis (sterile pack) diminui a carga microbiana dos frascos de envasamentos, o que diminuiria a chance de exposição a uma potencial contaminação da solução anestésica.

Safety and efficacy of multiuse botulinum toxin vials for intralaryngeal injection.

Science.gov (United States)

Barrow, Emily M; Rosen, Clark A; Hapner, Edie R; Smith, Sarah; Hatcher, Jeanne L; Simpson, Blake; Johns, Michael M

2015-05-01

Centers for Disease Control and Prevention guidelines maintain that single-use vials cannot be used for multiple patients. Botox product labeling states that the reconstituted toxin should be used within 4 hours on a single patient based on concerns of reduced potency, contamination, and consequent infections. The purpose of this study was to determine the safety and efficacy of using single-use vials in a multidose fashion. Prospective study and cohort chart review. A multi-institutional three-part study was performed between May 2013 and October 2013: 1) a summation of subjects' recall of their past experiences (symptoms/response) with previous multidose Botox injections, 2) a prospective study of intralaryngeal injections, and 3) a chart review of injection responses in a subset of the cohort. Seven hundred forty-three subjects receiving 6,216 injections demonstrated zero infection-related complications on retrospective chart review. One hundred seventy-nine subjects recalled 24.0% overall adverse events, 10.6% redness, 7.3% pain and swelling at the injection site, and 0% fever. One hundred seventy-four subjects prospectively reported 12.6% overall adverse events. The self-reported efficacy rate of Botox injection was 96.6%. The low rates of adverse events following the use of Botox in a multipatient fashion are consistent with other percutaneous injections. No evidence of infection was found with multidose Botox use. Given the low incidence of side effects and high success rate, Botox can be used both safely and effectively in a multipatient fashion. 4 © 2014 The American Laryngological, Rhinological and Otological Society, Inc.

Modelo y simulación de una intersección vial usando el software Arena

Directory of Open Access Journals (Sweden)

Sebastian Puerto Hernández

2015-06-01

Full Text Available En este artículo se presenta el modelo y la simulación de una intersección vial. Para modelar las dinámicas fue seleccionado el software Arena®, por su gran versatilidad y amplitud en herramientas a la hora de diseñar y modelar sistemas estocásticos. Las simulaciones en eventos discretos de la intersección validarán el modelo. Con el modelo obtenido se podrá realizar el cambio en la programación de los semáforos, la inclusión de paraderos en sitios específicos de las vías, y además la demostración de la relación entre la forma de conducción y estos problemas de movilidad. Se busca disminuir el tamaño de las colas que se generan, además de una reducción en los tiempos de recorridos de los usuarios en estos tramos y un mejoramiento notable en el funcionamiento vial en general de la ciudad.

Comparison of solid-phase bioassays and ecoscores to evaluate the toxicity of contaminated soils.

OpenAIRE

Lors , Christine; Ponge , Jean-François; Martínez Aldaya , Maite; Damidot , Denis

2010-01-01

International audience; Five bioassays (inhibition of lettuce germination and growth, earthworm mortality, inhibition of springtail population growth, avoidance by springtails) were compared, using four coke factory soils contaminated by PAHs and trace elements, before and after biotreatment. For each bioassay, several endpoints were combined in an 'ecoscore', a measure of test sensitivity. Ecoscores pooled over all tested bioassays revealed that most organisms were highly sensitive to the co...

Interpretation of thorium bioassay data

International Nuclear Information System (INIS)

Juliao, L.M.Q.C.; Azeredo, A.M.G.F.; Santos, M.S.; Melo, D.R.; Dantas, B.M.; Lipsztein, J.L.

1994-01-01

A comparison have been made between bioassay data of thorium-exposed workers from two different facilities. The first of these facilities is a monazite sand extraction plant. Isotopic equilibrium between 232 Th and 238 Th was not observed in excreta samples of these workers. The second facility is a gas mantle factory. An isotopic equilibrium between 232 Th and 228 Th was observed in extra samples. Whole body counter measurements have indicated a very low intake of thorium through inhalation. As the concentration of thorium in feces was very high it was concluded that the main pathway of entrance of the nuclide was ingestion, mainly via contamination through dirty hands. The comparison between the bioassay results of workers from the two facilities shows that the lack of Th isotopic equilibrium observed in the excretion from the workers at the monazite sand plant possibly occurred due to an additional Th intake by ingestion of contaminated fresh food. This is presumably because 228 Ra is more efficiently taken up from the soil by plants, in comparison to 228 Th or 232 Th, and subsequently, 228 Th grows in from its immediate parent, 228 Ra. (author) 5 refs.; 3 tabs

Micro-organism distribution sampling for bioassays

Science.gov (United States)

Nelson, B. A.

1975-01-01

Purpose of sampling distribution is to characterize sample-to-sample variation so statistical tests may be applied, to estimate error due to sampling (confidence limits) and to evaluate observed differences between samples. Distribution could be used for bioassays taken in hospitals, breweries, food-processing plants, and pharmaceutical plants.

Initial sample extract stock concentration affects in vitro bioassay-based toxicological risk characterization

NARCIS (Netherlands)

Montano, M.; Loffmann, L.; Murk, A.J.; Gutleb, A.C.

2014-01-01

Purpose Bioassays have become an alternative for sediment risk profiling, including potential compliance with sediment quality criteria (SQC). In vitro functional bioassays have evolved through standardization and validation towards a confident toxicological hazard estimate of sediments. Sample

False-positive cryptococcal antigen test associated with use of BBL Port-a-Cul transport vials.

Science.gov (United States)

Wilson, Deborah A; Sholtis, Mary; Parshall, Sharon; Hall, Gerri S; Procop, Gary W

2011-02-01

A total of 52 residual CSF and serum specimens, which were originally negative with the Cryptococcal Antigen Latex Agglutination System (CALAS), were shown to become falsely positive after placement in BBL Port-A-Cul anaerobic transport vials. This transport device, although excellent for specimen transportation for subsequent culture, should not be used if cryptococcal antigen testing is needed.

Componentes descriptivos y explicativos de la accidentalidad vial en Colombia: Incidencia del factor humano

Directory of Open Access Journals (Sweden)

Ervyn H. Norza Céspedes

2016-03-01

Full Text Available Problema: Se analizó la incidencia del factor humano en la accidentalidad vial en el territorio colombiano, y se identificó evidencia empírica para la formulación de política pública del tránsito. Metodología: El diseño es descriptivo-correlacional. Instrumentos: cuestionario de comportamiento para conductores y motociclistas (D.B.Q. y encuesta tipo Likert. Muestra no probabilística intencional: 16.322 personas (8.631 conductores de automotores, 5.133 motociclistas y 2.558 peatones, pasajeros y acompañantes. Resultados: a conductores con nivel educativo superior inciden en menos accidentes; b peatones con menor nivel educativo inciden en mayores conductas riesgosas; c las mujeres tienen actitud positiva y perciben eficacia de campañas en prevencion; d estilos de conducción iracundo, ansioso, riesgoso y de alta velocidad cometen más infracciones y accidentes; e desobedecer señales de tránsito, la principal causa de accidentalidad; f agresividad, hostilidad y estrés en el tránsito son factores que aumentan la probabilidad de accidente; g campañas de prevención no están siendo captadas por la población más afectada. Conclusiones y recomendaciones: Los factores de accidentalidad vial guardan correspondencia con el Triángulo de Seguridad Vial establecido por la Organización de las Naciones Unidas -factor humano preponderante en la accidentalidad-. Lineamientos de política pública fundamentados en procesos educativos y corporativos tendientes a disminuir la accidentalidad por lo general no se concibe aplicada a la seguridad pública. Por ello, se presenta la inteligencia criminal como una disciplina que se ocupa de anticipar los riesgos criminales contra la seguridad pública. Esto permitiría disminuir la incertidumbre durante la toma de decisiones y calcular los daños contra la seguridad pública, que se pretende prevenir.

Activities of Jatropha curcas phorbol esters in various bioassays.

Science.gov (United States)

Devappa, Rakshit K; Rajesh, Sanjay K; Kumar, Vikas; Makkar, Harinder P S; Becker, Klaus

2012-04-01

Jatropha curcas seeds contain 30-35% oil, which can be converted to high quality biodiesel. However, Jatropha oil is toxic, ascribed to the presence of phorbol esters (PEs). In this study, isolated phorbol ester rich fraction (PEEF) was used to evaluate the activity of PEs using three aquatic species based bioassays (snail (Physa fontinalis), brine shrimp (Artemeia salina), daphnia (Daphnia magna)) and microorganisms. In all the bioassays tested, increase in concentration of PEs increased mortality with an EC(50) (48 h) of 0.33, 26.48 and 0.95 mg L(-1) PEs for snail, artemia and daphnia, respectively. The sensitivity of various microorganisms for PEs was also tested. Among the bacterial species tested, Streptococcus pyogenes and Proteus mirabilis were highly susceptible with a minimum inhibitory concentration (MIC) of 215 mg L(-1) PEs; and Pseudomonas putida were also sensitive with MIC of 251 mg L(-1) PEs. Similarly, Fusarium species of fungi exhibited EC(50) of 58 mg L(-1) PEs, while Aspergillus niger and Curvularia lunata had EC(50) of 70 mg L(-1). The snail bioassay was most sensitive with 100% snail mortality at 1 μg of PEs mL(-1). In conclusion, snail bioassay could be used to monitor PEs in Jatropha derived products such as oil, biodiesel, fatty acid distillate, kernel meal, cake, glycerol or for contamination in soil or other environmental matrices. In addition, PEs with molluscicidal/antimicrobial activities could be utilized for agricultural and pharmaceutical applications. Copyright © 2011 Elsevier Inc. All rights reserved.

Impact of Vial Capping on Residual Seal Force and Container Closure Integrity.

Science.gov (United States)

Mathaes, Roman; Mahler, Hanns-Christian; Roggo, Yves; Ovadia, Robert; Lam, Philippe; Stauch, Oliver; Vogt, Martin; Roehl, Holger; Huwyler, Joerg; Mohl, Silke; Streubel, Alexander

2016-01-01

The vial capping process is a critical unit operation during drug product manufacturing, as it could possibly generate cosmetic defects or even affect container closure integrity. Yet there is significant variability in capping equipment and processes, and their relation to potential defects or container closure integrity has not been thoroughly studied. In this study we applied several methods-residual seal force tester, a self-developed system of a piezo force sensor measurement, and computed tomography-to characterize different container closure system combinations that had been sealed using different capping process parameter settings. Additionally, container closure integrity of these samples was measured using helium leakage (physical container closure integrity) and compared to characterization data. The different capping equipment settings lead to residual seal force values from 7 to 115 N. High residual seal force values were achieved with high capping pre-compression force and a short distance between the capping plate and plunge. The choice of container closure system influenced the obtained residual seal force values. The residual seal force tester and piezoelectric measurements showed similar trends. All vials passed physical container closure integrity testing, and no stopper rupture was seen with any of the settings applied, suggesting that container closure integrity was warranted for the studied container closure system with the chosen capping setting ranges. The vial capping process is a critical unit operation during drug product manufacturing, as it could possibly generate cosmetic defects or even affect container closure integrity. Yet there is significant variability in capping equipment and processes, and their relation to potential defects or container closure integrity has not been thoroughly studied. In this study we applied several methods-residual seal force tester, a self-developed system of a piezo force sensor measurement, and

Generating chimeric mice from embryonic stem cells via vial coculturing or hypertonic microinjection.

Science.gov (United States)

Lee, Kun-Hsiung

2014-01-01

The generation of a fertile embryonic stem cell (ESC)-derived or F0 (100 % coat color chimerism) mice is the final criterion in proving that the ESC is truly pluripotent. Many methods have been developed to produce chimeric mice. To date, the most popular methods for generating chimeric embryos is well sandwich aggregation between zona pellucida (ZP) removed (denuded) 2.5-day post-coitum (dpc) embryos and ESC clumps, or direct microinjection of ESCs into the cavity (blastocoel) of 3.5-dpc blastocysts. However, due to systemic limitations and the disadvantages of conventional microinjection, aggregation, and coculturing, two novel methods (vial coculturing and hypertonic microinjection) were developed in recent years at my laboratory.Coculturing 2.5-dpc denuded embryos with ESCs in 1.7-mL vials for ~3 h generates chimeras that have significantly high levels of chimerism (including 100 % coat color chimerism) and germline transmission. This method has significantly fewer instrumental and technological limitations than existing methods, and is an efficient, simple, inexpensive, and reproducible method for "mass production" of chimeric embryos. For laboratories without a microinjection system, this is the method of choice for generating chimeric embryos. Microinjecting ESCs into a subzonal space of 2.5-dpc embryos can generate germline-transmitted chimeras including 100 % coat color chimerism. However, this method is adopted rarely due to the very small and tight space between ZP and blastomeres. Using a laser pulse or Piezo-driven instrument/device to help introduce ESCs into the subzonal space of 2.5-dpc embryos demonstrates the superior efficiency in generating ESC-derived (F0) chimeras. Unfortunately, due to the need for an expensive instrument/device and extra fine skill, not many studies have used either method. Recently, ESCs injected into the large subzonal space of 2.5-dpc embryos in an injection medium containing 0.2-0.3 M sucrose very efficiently generated

DWPF Sample Vial Insert Study-Statistical Analysis of DWPF Mock-Up Test Data

International Nuclear Information System (INIS)

Harris, S.P.

1997-01-01

This report is prepared as part of Technical/QA Task Plan WSRC-RP-97-351 which was issued in response to Technical Task Request HLW/DWPF/TTR-970132 submitted by DWPF. Presented in this report is a statistical analysis of DWPF Mock-up test data for evaluation of two new analytical methods which use insert samples from the existing HydragardTM sampler. The first is a new hydrofluoric acid based method called the Cold Chemical Method (Cold Chem) and the second is a modified fusion method.Both new methods use the existing HydragardTM sampler to collect a smaller insert sample from the process sampling system. The insert testing methodology applies to the DWPF Slurry Mix Evaporator (SME) and the Melter Feed Tank (MFT) samples. Samples in small 3 ml containers (Inserts) are analyzed by either the cold chemical method or a modified fusion method. The current analytical method uses a HydragardTM sample station to obtain nearly full 15 ml peanut vials. The samples are prepared by a multi-step process for Inductively Coupled Plasma (ICP) analysis by drying, vitrification, grinding and finally dissolution by either mixed acid or fusion. In contrast, the insert sample is placed directly in the dissolution vessel, thus eliminating the drying, vitrification and grinding operations for the Cold chem method. Although the modified fusion still requires drying and calcine conversion, the process is rapid due to the decreased sample size and that no vitrification step is required.A slurry feed simulant material was acquired from the TNX pilot facility from the test run designated as PX-7.The Mock-up test data were gathered on the basis of a statistical design presented in SRT-SCS-97004 (Rev. 0). Simulant PX-7 samples were taken in the DWPF Analytical Cell Mock-up Facility using 3 ml inserts and 15 ml peanut vials. A number of the insert samples were analyzed by Cold Chem and compared with full peanut vial samples analyzed by the current methods. The remaining inserts were analyzed by

Soil plate bioassay: an effective method to determine ecotoxicological risks.

Science.gov (United States)

Boluda, R; Roca-Pérez, L; Marimón, L

2011-06-01

Heavy metals have become one of the most serious anthropogenic stressors for plants and other living organisms. Having efficient and feasible bioassays available to assess the ecotoxicological risks deriving from soil pollution is necessary. This work determines pollution by Cd, Co, Cr, Cu, Ni, Pb, V and Zn in two soils used for growing rice from the Albufera Natural Park in Valencia (Spain). Both were submitted to a different degree of anthropic activity, and their ecotoxicological risk was assessed by four ecotoxicity tests to compare their effectiveness: Microtox test, Zucconi test, pot bioassay (PB) and soil plate bioassay (SPB). The sensitivity of three plant species (barley, cress and lettuce) was also assessed. The results reveal a different degree of effectiveness and level of inhibition in the target organisms' growth depending on the test applied, to such an extent that the one-way analysis of variance showed significant differences only for the plate bioassay results, with considerable inhibition of root and shoot elongation in seedlings. Of the three plant species selected, lettuce was the most sensitive species to toxic effects, followed by cress and barley. Finally, the results also indicate that the SPB is an efficient, simple and economic alternative to other ecotoxicological assays to assess toxicity risks deriving from soil pollution. Copyright © 2011 Elsevier Ltd. All rights reserved.

Calibration-free sensor for pressure and H2O concentration in headspace of sterile vial using tunable diode laser absorption spectroscopy.

Science.gov (United States)

Cai, Tingdong; Gao, Guangzhen; Liu, Ying

2013-11-10

Tunable diode laser absorption measurements of pressure and H2O concentration in the headspace of vials using a distributed-feedback (DFB) diode laser near 1.4 μm are reported. A H2O line located near 7161.41 cm(-1) is selected based on its strong absorption strength and isolation from interference of neighboring transitions. Direct absorption spectra of H2O are obtained for the measurement path as well as the reference path by scanning the laser wavelength. The pressure and H2O vapor concentration in the headspace of a vial are inferred from a differential absorption signal, which is the difference between the measured and the referenced absorbance spectra. This sensor is calibration-free and no purge gas is needed. The demonstrated capability would enable measurements of pressure and H2O concentration in the headspace of vials within 2.21% and 2.86%, respectively. A precision of 1.02 Torr and 390 ppm is found for the pressure and H2O concentration, respectively. A set of measurements for commercial freeze-dried products are also performed to illustrate the usefulness of this sensor.

In vitro bioassays to evaluate complex chemical mixtures in recycled water.

Science.gov (United States)

Jia, Ai; Escher, Beate I; Leusch, Frederic D L; Tang, Janet Y M; Prochazka, Erik; Dong, Bingfeng; Snyder, Erin M; Snyder, Shane A

2015-09-01

With burgeoning population and diminishing availability of freshwater resources, the world continues to expand the use of alternative water resources for drinking, and the quality of these sources has been a great concern for the public as well as public health professionals. In vitro bioassays are increasingly being used to enable rapid, relatively inexpensive toxicity screening that can be used in conjunction with analytical chemistry data to evaluate water quality and the effectiveness of water treatment. In this study, a comprehensive bioassay battery consisting of 36 bioassays covering 18 biological endpoints was applied to screen the bioactivity of waters of varying qualities with parallel treatments. Samples include wastewater effluent, ultraviolet light (UV) and/or ozone advanced oxidation processed (AOP) recycled water, and infiltrated recycled groundwater. Based on assay sensitivity and detection frequency in the samples, several endpoints were highlighted in the battery, including assays for genotoxicity, mutagenicity, estrogenic activity, glucocorticoid activity, arylhydrocarbon receptor activity, oxidative stress response, and cytotoxicity. Attenuation of bioactivity was found to be dependent on the treatment process and bioassay endpoint. For instance, ozone technology significantly removed oxidative stress activity, while UV based technologies were most efficient for the attenuation of glucocorticoid activity. Chlorination partially attenuated genotoxicity and greatly decreased herbicidal activity, while groundwater infiltration efficiently attenuated most of the evaluated bioactivity with the exception of genotoxicity. In some cases, bioactivity (e.g., mutagenicity, genotoxicity, and arylhydrocarbon receptor) increased following water treatment, indicating that transformation products of water treatment may be a concern. Furthermore, several types of bioassays with the same endpoint were compared in this study, which could help guide the selection

Comparison of analysis techniques by liquid scintillation and Cerenkov Effect for 40K quantification in aqueous samples

International Nuclear Information System (INIS)

Miranda C, L.; Davila R, J. I.; Lopez del R, H.; Mireles G, F.

2015-09-01

In this work the counting by liquid scintillation and Cerenkov Effect to quantify 40 K in aqueous samples was used. The performance of both techniques was studied by comparing the response of three commercial liquid scintillation OptiPhase HiSafe 3, Ultima Gold Ab and OptiPhase TriSafe, the vial type and presentation conditions of the sample for counting. In liquid scintillation, the ability to form homogeneous mixtures depended on the ionic strength of the aqueous solutions. The scintillator OptiPhase HiSafe 3 showed a greater charge capacity for solutions with high ionic strength (<3.4), while the scintillator OptiSafe TriSafe no form homogeneous mixtures for solutions of ionic strength higher than 0.3. Counting efficiencies for different proportions of sample and scintillator near 100% for the scintillators OptiSafe HiSafe 3 and Ultima Gold Ab were obtained. In the counting by Cerenkov Effect, the efficiency and sensitivity depended of the vial type; polyethylene vials were more suitable for counting that the glass vials. The sample volume had not significant effect on counting efficiency, obtaining an average value of 44.8% for polyethylene vials and 37.3% for glass vials. Therefore, the liquid scintillation was more efficient and sensitive for the measurement of 40 K in aqueous solutions. (Author)

A rapid bioassay for detecting saxitoxins using a Daphnia acute toxicity test.

Science.gov (United States)

Ferrão-Filho, Aloysio da S; Soares, Maria Carolina S; de Magalhães, Valéria Freitas; Azevedo, Sandra M F O

2010-06-01

Bioassays using Daphnia pulex and Moina micrura were designed to detect cyanobacterial neurotoxins in raw water samples. Phytoplankton and cyanotoxins from seston were analyzed during 15 months in a eutrophic reservoir. Effective time to immobilize 50% of the exposed individuals (ET50) was adopted as the endpoint. Paralysis of swimming movements was observed between approximately 0.5-3 h of exposure to lake water containing toxic cyanobacteria, followed by an almost complete recovery of the swimming activity within 24 h after being placed in control water. The same effects were observed in bioassays with a saxitoxin-producer strain of Cylindrospermopsis raciborskii isolated from the reservoir. Regression analysis showed significant relationships between ET50 vs. cell density, biomass and saxitoxins content, suggesting that the paralysis of Daphnia in lake water samples was caused by saxitoxins found in C. raciborskii. Daphnia bioassay was found to be a sensitive method for detecting fast-acting neurotoxins in natural samples, with important advantages over mouse bioassays. Copyright 2010 Elsevier Ltd. All rights reserved.

Evaluation of the toxicity of two soils from Jales Mine (Portugal) using aquatic bioassays.

Science.gov (United States)

Loureiro, Susana; Ferreira, Abel L G; Soares, Amadeu M V M; Nogueira, António J A

2005-10-01

Soil contamination can be one path for streams and groundwater contamination. As a complement of chemical analysis and total contaminants determination, bioassays can provide information on the bioavailable fraction of chemical compounds, focusing on the retention and habitat function of soils. In this study the evaluation of the toxicity of two soils from the abandoned Jales Mine (Portugal) regarded both functions. The buffer capacity of soils was tested with bioassays carried out using the cladoceran Daphnia magna and the marine bacteria Vibrio fischeri. The habitat function of soils was evaluated with the reproduction bioassay with the collembolan Folsomia candida. The Microtox solid-phase test was performed with V. fischeri using soil as test medium, and soil elutriates were extracted to perform the Microtox basic test, and an immobilization and reproduction bioassay with D. magna. The marine bacteria showed high sensitivity to the soil with low heavy metal content (JNC soil) and to JNC soil elutriates, while the soil with highest heavy metal content (JC soil) or soil elutriates exposure did not cause any toxic effect. In the bioassays with D. magna, organisms showed sensitivity to JNC and also to JC soil elutriates. Both mobilization and reproduction features were inhibited. The bioassay with F. candida did not reflect any influence of the contaminants on their reproduction. Although JNC soil presented lower heavy metal contents, elutriates showed different patterns of contamination when compared to JC soil and elutriates, which indicates different retention and buffer capacities between soils. Results obtained in this study underlined the sensitivity and importance of soil elutriate bioassays with aquatic organisms in the evaluation strategy in soil ERA processes.

Benchmarking organic micropollutants in wastewater, recycled water and drinking water with in vitro bioassays.

Science.gov (United States)

Escher, Beate I; Allinson, Mayumi; Altenburger, Rolf; Bain, Peter A; Balaguer, Patrick; Busch, Wibke; Crago, Jordan; Denslow, Nancy D; Dopp, Elke; Hilscherova, Klara; Humpage, Andrew R; Kumar, Anu; Grimaldi, Marina; Jayasinghe, B Sumith; Jarosova, Barbora; Jia, Ai; Makarov, Sergei; Maruya, Keith A; Medvedev, Alex; Mehinto, Alvine C; Mendez, Jamie E; Poulsen, Anita; Prochazka, Erik; Richard, Jessica; Schifferli, Andrea; Schlenk, Daniel; Scholz, Stefan; Shiraishi, Fujio; Snyder, Shane; Su, Guanyong; Tang, Janet Y M; van der Burg, Bart; van der Linden, Sander C; Werner, Inge; Westerheide, Sandy D; Wong, Chris K C; Yang, Min; Yeung, Bonnie H Y; Zhang, Xiaowei; Leusch, Frederic D L

2014-01-01

Thousands of organic micropollutants and their transformation products occur in water. Although often present at low concentrations, individual compounds contribute to mixture effects. Cell-based bioassays that target health-relevant biological endpoints may therefore complement chemical analysis for water quality assessment. The objective of this study was to evaluate cell-based bioassays for their suitability to benchmark water quality and to assess efficacy of water treatment processes. The selected bioassays cover relevant steps in the toxicity pathways including induction of xenobiotic metabolism, specific and reactive modes of toxic action, activation of adaptive stress response pathways and system responses. Twenty laboratories applied 103 unique in vitro bioassays to a common set of 10 water samples collected in Australia, including wastewater treatment plant effluent, two types of recycled water (reverse osmosis and ozonation/activated carbon filtration), stormwater, surface water, and drinking water. Sixty-five bioassays (63%) showed positive results in at least one sample, typically in wastewater treatment plant effluent, and only five (5%) were positive in the control (ultrapure water). Each water type had a characteristic bioanalytical profile with particular groups of toxicity pathways either consistently responsive or not responsive across test systems. The most responsive health-relevant endpoints were related to xenobiotic metabolism (pregnane X and aryl hydrocarbon receptors), hormone-mediated modes of action (mainly related to the estrogen, glucocorticoid, and antiandrogen activities), reactive modes of action (genotoxicity) and adaptive stress response pathway (oxidative stress response). This study has demonstrated that selected cell-based bioassays are suitable to benchmark water quality and it is recommended to use a purpose-tailored panel of bioassays for routine monitoring.

A versatile electrowetting-based digital microfluidic platform for quantitative homogeneous and heterogeneous bio-assays

Science.gov (United States)

Vergauwe, Nicolas; Witters, Daan; Ceyssens, Frederik; Vermeir, Steven; Verbruggen, Bert; Puers, Robert; Lammertyn, Jeroen

2011-05-01

Electrowetting-on-dielectric (EWOD) lab-on-a-chip systems have already proven their potential within a broad range of bio-assays. Nevertheless, research on the analytical performance of those systems is limited, yet crucial for a further breakthrough in the diagnostic field. Therefore, this paper presents the intrinsic possibilities of an EWOD lab-on-a-chip as a versatile platform for homogeneous and heterogeneous bio-assays with high analytical performance. Both droplet dispensing and splitting cause variations in droplet size, thereby directly influencing the assay's performance. The extent to which they influence the performance is assessed by a theoretical sensitivity analysis, which allows the definition of a basic framework for the reduction of droplet size variability. Taking advantage of the optimized droplet manipulations, both homogeneous and heterogeneous bio-assays are implemented in the EWOD lab-on-a-chip to demonstrate the analytical capabilities and versatility of the device. A fully on-chip enzymatic assay is realized with high analytical performance. It demonstrates the promising capabilities of an EWOD lab-on-a-chip in food-related and medical applications, such as nutritional and blood analyses. Further, a magnetic bio-assay for IgE detection using superparamagnetic nanoparticles is presented whereby the nanoparticles are used as solid carriers during the bio-assay. Crucial elements are the precise manipulation of the superparamagnetic nanoparticles with respect to dispensing and separation. Although the principle of using nano-carriers is demonstrated for protein detection, it can be easily extended to a broader range of bio-related applications like DNA sensing. In heterogeneous bio-assays the chip surface is actively involved during the execution of the bio-assay. Through immobilization of specific biological compounds like DNA, proteins and cells a reactive chip surface is realized, which enhances the bio-assay performance. To demonstrate

Improving global laboratory capabilities for emergency radionuclide bioassay

International Nuclear Information System (INIS)

Li, C.; Jourdain, J.; Kramer, G. H.

2012-01-01

During a radiological or nuclear emergency, first-responders and the general public may be internally contaminated with the radionuclide(s) involved. A timely radionuclide bioassay provides important information about contamination, for subsequent dose assessment and medical management. Both technical and operational gaps are discussed in this paper. As many people may need to be assessed in a short period of time, any single laboratory may find its capabilities insufficient. Laboratories from other regions or other countries may be called upon for assistance. This paper proposes a road-map to improve global capabilities in emergency radionuclide bioassay, suggesting a phased approach for establishing a global laboratory network. Existing international collaboration platforms could provide the base on which to build such a network. (authors)

Radioactivity measurement of 18F in 16 ml vials for calibration of radionuclide calibrators

International Nuclear Information System (INIS)

Wurdiyanto, Gatot; Marsoem, Pujadi; Candra, Hermawan; Wijono, Paidi

2012-01-01

Fluorine-18 is obtained through the reaction 18 O(p, n) 18 F using a cyclotron that is situated in a hospital in Jakarta. Standardization of the 18 F solution is performed by gamma spectrometry using calibration sources of 152 Eu, 60 Co and 137 Cs that have traceability to the International System of units (SI). The activities in the 16 ml vials that were used for calibrating the radionuclide calibrators were between 1 and 2 GBq, with expanded uncertainties of 3.8%. The expanded uncertainty, at a coverage factor of k=2, on the derived calibration factor for the radionuclide calibrator was 6.6%. - Highlights: ► PTKMR–BATAN as a NMI of Indonesia is required to have procedures to calibrate the radionuclide calibrators. ► Standardizations were carried out on a solution of [ 18 F]FDG using gamma spectrometry. ► The volume of 18 F solutions used was 16 ml because this is the volume often used in hospitals. ► The Secondary Standard ionization chamber is a CRC-7BT Capintec radionuclide calibrator. ► A dial setting for 16 ml of [ 18 F]FDG solution in a vial is 443 for the Capintec dose calibrator.

The use of bioassays to assess the toxicity of sediment in an acid ...

African Journals Online (AJOL)

Exposure of river sediment from 7 sampling sites to these bioassays provided an eco-toxicological estimation of the acute toxicity and chronic toxicity emanating from the contaminated sediments. Physico-chemical analyses revealed higher levels of sediment contamination closer to the mine. The bioassays displayed a ...

Sample preparation for combined chemical analysis and bioassay application in water quality assessment

NARCIS (Netherlands)

Kolkman, A.; Schriks, M.; Brand, W; Bäuerlein, P.S.; van der Kooi, M.M.E.; van Doorn, R.H.; Emke, E.; Reus, A.; van der Linden, S.; de Voogt, P.; Heringa, M.B.

2013-01-01

The combination of in vitro bioassays and chemical screening can provide a powerful toolbox to determine biologically relevant compounds in water extracts. In this study, a sample preparation method is evaluated for the suitability for both chemical analysis and in vitro bioassays. A set of 39

The CALUX bioassay: current status of its application to screening food and feed

NARCIS (Netherlands)

Hoogenboom, L.A.P.; Goeyens, L.; Carbonnelle, S.; Loco, van J.; Beernaert, H.; Baeyens, W.; Traag, W.A.; Bovee, T.F.H.; Jacobs, G.; Schoeters, G.

2006-01-01

The CALUX bioassay is at present the best screening method for dioxins and dioxin-like (dl) polychlorinated biphenyls (PCBs) in food and feed, and the only assay used in routine monitoring and during larger incidents. Furthermore, the use of bioassays in addition to chemical reference methods allows

Vaccine Wastage Assessment After Introduction of Open Vial Policy in Surat Municipal Corporation Area of India.

Science.gov (United States)

Patel, Prakash B; Rana, Jayesh J; Jangid, Sunil G; Bavarva, Neha R; Patel, Manan J; Bansal, Raj Kumar

2015-12-08

As per the vaccine management policy of the Government of India all vaccine vials opened for an immunization session were discarded at the end of that session, irrespective of the type of vaccine or the number of doses remaining in the vial prior to 2013. Subsequently, open vial policy (OVP) was introduced in 2013 and should reduce both vaccine wastage as well as governmental healthcare costs for immunization. This study evaluates the vaccine wastage after introduction of the OVP and its comparison with the previous study of vaccine wastage in Surat city before implementation of OVP. It needs to mention that the vaccine policy for this period under comparison was uniform except for the OVP. Information regarding vaccine doses consumed and children vaccinated during immunization sessions of 24 urban health centers (UHCs) of Surat city were retrieved for the period of January 1st, 2014 to March 31st, 2014. The data were analyzed to estimate vaccine wastage rate (WR) and vaccine wastage factor (WF). In order to assess the impact of OVP, vaccine WR of this study was compared with that of previous study conducted in Surat city during January 1st, 2012 to March 31st, 2012. The vaccine WR for oral polio vaccine (OPV) has decreased from 25% to 13.62%, while the WRs for DPT, hepatitis B virus (HBV) and the pentavalent vaccine combinedly have decreased from 17.94% to 8.05%. Thus, by implementation of OVP, an estimated 747 727 doses of OPV and 343 725 doses of diphtheria, pertussis and tetanus toxoid vaccine (DPT), HBV and the pentavalent vaccines combinedly have been saved in Surat city of India in a year. The implementation of the OVP in Surat city has led to a significant lowering in the vaccine wastage, leading to savings due to lower vaccine requirements. © 2016 by Kerman University of Medical Sciences.

Assessment of acrylamide toxicity using a battery of standardised bioassays.

Science.gov (United States)

Zovko, Mira; Vidaković-Cifrek, Željka; Cvetković, Želimira; Bošnir, Jasna; Šikić, Sandra

2015-12-01

Acrylamide is a monomer widely used as an intermediate in the production of organic chemicals, e.g. polyacrylamides (PAMs). Since PAMs are low cost chemicals with applications in various industries and waste- and drinking water treatment, a certain amount of non-polymerised acrylamide is expected to end up in waterways. PAMs are non-toxic but acrylamide induces neurotoxic effects in humans and genotoxic, reproductive, and carcinogenic effects in laboratory animals. In order to evaluate the effect of acrylamide on freshwater organisms, bioassays were conducted on four species: algae Desmodesmus subspicatus and Pseudokirchneriella subcapitata, duckweed Lemna minor and water flea Daphnia magna according to ISO (International Organization for Standardisation) standardised methods. This approach ensures the evaluation of acrylamide toxicity on organisms with different levels of organisation and the comparability of results, and it examines the value of using a battery of low-cost standardised bioassays in the monitoring of pollution and contamination of aquatic ecosystems. These results showed that EC50 values were lower for Desmodesmus subspicatus and Pseudokirchneriella subcapitata than for Daphnia magna and Lemna minor, which suggests an increased sensitivity of algae to acrylamide. According to the toxic unit approach, the values estimated by the Lemna minor and Daphnia magna bioassays, classify acrylamide as slightly toxic (TU=0-1; Class 1). The results obtained from algal bioassays (Desmodesmus subspicatus and Pseudokirchneriella subcapitata) revealed the toxic effect of acrylamide (TU=1-10; Class 2) on these organisms.

Comparison of solid-phase bioassays and ecoscores to evaluate the toxicity of contaminated soils

Energy Technology Data Exchange (ETDEWEB)

Lors, Christine [Universite Lille Nord de France, 1bis rue Georges Lefevre, 59044 Lille Cedex (France); Ecole des Mines de Douai, MPE-GCE, 941 rue Charles-Bourseul, 59500 Douai (France); Centre National de Recherche sur les Sites et Sols Pollues, 930 Boulevard Lahure, BP 537, 59505 Douai Cedex (France); Ponge, Jean-Francois, E-mail: ponge@mnhn.f [Museum National d' Histoire Naturelle, CNRS UMR 7179, 4 Avenue du Petit-Chateau, 91800 Brunoy (France); Martinez Aldaya, Maite [Museum National d' Histoire Naturelle, CNRS UMR 7179, 4 Avenue du Petit-Chateau, 91800 Brunoy (France); Damidot, Denis [Universite Lille Nord de France, 1bis rue Georges Lefevre, 59044 Lille Cedex (France); Ecole des Mines de Douai, MPE-GCE, 941 rue Charles-Bourseul, 59500 Douai (France)

2010-08-15

Five bioassays (inhibition of lettuce germination and growth, earthworm mortality, inhibition of springtail population growth, avoidance by springtails) were compared, using four coke factory soils contaminated by PAHs and trace elements, before and after biotreatment. For each bioassay, several endpoints were combined in an 'ecoscore', a measure of test sensitivity. Ecoscores pooled over all tested bioassays revealed that most organisms were highly sensitive to the concentration of 3-ring PAHs. When four soils were combined, behavioural tests using the springtail Folsomia candida showed higher ecoscores, i.e. they were most sensitive to soil contamination. However, despite overall higher sensitivity of behavioural tests, which could be used for cheap and rapid assessment of soil toxicity, especially at low levels of contamination, some test endpoints were more sensitive than others, and this may differ from a soil to another, pointing to the need for a battery of bioassays when more itemized results are expected. - The avoidance test using the soil springtail Folsomia candida is globally more sensitive to PAH contamination than acute and chronic toxicity bioassays using plants and animals but a battery of tests could reveal better in detail.

Comparison of solid-phase bioassays and ecoscores to evaluate the toxicity of contaminated soils

International Nuclear Information System (INIS)

Lors, Christine; Ponge, Jean-Francois; Martinez Aldaya, Maite; Damidot, Denis

2010-01-01

Five bioassays (inhibition of lettuce germination and growth, earthworm mortality, inhibition of springtail population growth, avoidance by springtails) were compared, using four coke factory soils contaminated by PAHs and trace elements, before and after biotreatment. For each bioassay, several endpoints were combined in an 'ecoscore', a measure of test sensitivity. Ecoscores pooled over all tested bioassays revealed that most organisms were highly sensitive to the concentration of 3-ring PAHs. When four soils were combined, behavioural tests using the springtail Folsomia candida showed higher ecoscores, i.e. they were most sensitive to soil contamination. However, despite overall higher sensitivity of behavioural tests, which could be used for cheap and rapid assessment of soil toxicity, especially at low levels of contamination, some test endpoints were more sensitive than others, and this may differ from a soil to another, pointing to the need for a battery of bioassays when more itemized results are expected. - The avoidance test using the soil springtail Folsomia candida is globally more sensitive to PAH contamination than acute and chronic toxicity bioassays using plants and animals but a battery of tests could reveal better in detail.

Experience with NQA-1 quality assurance standards applied to in vitro bioassay

International Nuclear Information System (INIS)

Bihl, D.E.; MacLellan, J.A.

1991-10-01

On June 1, 1990, the large (about 4000 samples per year) excreta bioassay program at the Hanford Site ceased abruptly when the contract with the bioassay laboratory was terminated. An intense, high-priority effort was begun to replace the services on an interim basis until a new contract could be procured. Despite the urgency to get the excreta bioassay program going again, the Hanford Internal Dosimetry Program was constrained to use only labs that could meet stringent quality assurance (QA) requirements, even during the interim period. The QA requirements were based on NQA-1 with selected additions from the Environmental Protection Agency's QAMS 005/80 (EPA 1983) and the American Society for Testing and Materials' C 1009-83 (ASTM 1984). This constraint was driven both by legal reasons and by the Hanford Site contractors and workers not wanting the quality of the data to be sacrificed. Finding labs that could (1) handle the large throughput, (2) meet the technical requirements, and (3) pass the QA audit proved more difficult than first anticipated. This presentation focuses on the QA requirements that the labs had to meet and how those very broad requirements were applied specifically to excreta bioassay. 5 refs

Experience with NQA-1 quality assurance standards applied to in vitro bioassay

International Nuclear Information System (INIS)

Bihl, D.E.; MacLellan, J.A.

1991-01-01

On June 1, 1990, the large (about 4,000 samples per year) excreta bioassay program at the Hanford Site ceased abruptly when the contract with the bioassay laboratory was terminated. An intense, high-priority effort was begun to replace the services on an interim basis until a new contract could be procured. Despite the urgency to get the excreta bioassay program going again, the Hanford Internal Dosimetry Program was constrained to use only labs that could meet stringent quality assurance (QA) requirements, even during the interim period. The QA requirements were based on NQA-1 with selected additions from the Environmental Protection Agency's QAMS 005/80 (EPA 1983) and the American Society for Testing and Materials' C 1009-83 (ASTM 1984). This constraint was driven both by legal reasons and by the Hanford Site contractors and workers not wanting the quality of the data to be sacrificed. Finding labs that could (1) handle the large throughput, (2) meet the technical requirements, and (3) pass the QA audit proved more difficult than first anticipated. This presentation focuses on the QA requirements that the labs had to meet and how those very broad requirements were applied specifically to excreta bioassay

Evaluation of a high-throughput peptide reactivity format assay for assessment of the skin sensitization potential of chemicals

Directory of Open Access Journals (Sweden)

Chin Lin eWong

2016-03-01

Full Text Available The direct peptide reactivity assay (DPRA is a validated method for in vitro assessment of the skin sensitization potential of chemicals. In the present work, we describe a peptide reactivity assay using 96-well plate format and systematically identified the optimal assay conditions for accurate and reproducible classification of chemicals with known sensitizing capacity. The aim of the research is to ensure that the analytical component of the peptide reactivity assay is robust, accurate and reproducible in accordance with criteria that are used for the validation of bioanalytical methods. Analytical performance was evaluated using quality control samples (QCs; heptapeptides at low, medium and high concentrations and incubation of control chemicals (chemicals with known sensitization capacity, weak, moderate, strong, extreme and non-sensitizers with each of three synthetic heptapeptides, viz Cor1-C420 (Ac-NKKCDLF, cysteine- (Ac-RFAACAA and lysine- (Ac-RFAAKAA containing heptapeptides. The optimal incubation temperature for all three heptapeptides was 25°C. Apparent heptapeptide depletion was affected by vial material composition. Incubation of test chemicals with Cor1-C420, showed that peptide depletion was unchanged in polypropylene vials over 3-days storage in an autosampler but this was not the case for borosilicate glass vials. For cysteine-containing heptapeptide, the concentration was not stable by day 3 post-incubation in borosilicate glass vials. Although the lysine-containing heptapeptide concentration was unchanged in both polypropylene and borosilicate glass vials, the apparent extent of lysine-containing heptapeptide depletion by ethyl acrylate, differed between polypropylene (24.7% and glass (47.3% vials. Additionally, the peptide-chemical complexes for Cor1-C420-cinnamaldehyde and cysteine-containing heptapeptide-2,4-dinitrochlorobenzene were partially reversible during 3-days of autosampler storage. These observations further

The 10th Annual Bioassays and Bioanalytical Method Development Conference.

Science.gov (United States)

Ma, Mark; Tudan, Christopher; Koltchev, Dolly

2015-01-01

The 10th Annual Bioassays and Bioanalytical Method Development Conference was hosted in Boston, MA, USA on 20-22 October 2014. This meeting brought together scientists from the biopharmaceutical and life sciences industries, the regulatory agency and academia to share and discuss current trends in cell-based assays and bioanalysis, challenges and ideas for the future of the bioassays and bioanalytical method development. The experiences associated with new and innovative technologies were evaluated as well as their impact on the current bioassays methodologies and bioanalysis workflow, including quality, feasibility, outsourcing strategies and challenges, productivity and compliance. Several presentations were also provided by members of the US FDA, sharing both scientific and regulatory paradigms including a most recent update on the position of the FDA with specific aspects of the draft Bioanalytical Method Validation guidance following its review of the industry's responses. The meeting was jointly coincided with the 15th Annual Immunogenicity for Biotherapeutics meeting, allowing for attendees to also familiarize themselves with new and emerging approaches to overcome the effect of immunogenicity, in addition to investigative strategies.

The radiation sterilisation of pyrogen-free water in polyethylene sachets

International Nuclear Information System (INIS)

Du Plessis, T.A.

1977-06-01

The radiation sterilization of pyrogen-free water in polyester/polyethylene-laminate sachets was investigated. A technique was developed to ensure the sterile removal of the water from the sachet. The production of hydrogen peroxide as the major radiolytic product was investigated for water irradiated in both glass vials and polymer sachets. It was found that the formation of hydrogen peroxide in the polymer sachets was only half of that formed in the glass vials. The radiation-sterilised water was found to comply in all respects with the British Pharmacopoeia requirements for water for injections [af

9 CFR 147.16 - Procedure for the evaluation of mycoplasma reactors by in vivo bio-assay (enrichment).

Science.gov (United States)

2010-01-01

... mycoplasma reactors by in vivo bio-assay (enrichment). 147.16 Section 147.16 Animals and Animal Products... the evaluation of mycoplasma reactors by in vivo bio-assay (enrichment). This procedure has been shown... publications: (a) Bigland, C. H. and A. J. DaMassa, “A Bio-Assay for Mycoplasma Gallisepticum.” In: United...

Development by flow cytometry of bioassays based on chlorella for environmental monitoring

Directory of Open Access Journals (Sweden)

Petrescu C-M,

2016-05-01

Full Text Available In ecotoxicological assessments, bioassays (ecotoxicity tests or biotests are one of the main tools, defined as methods which use living cells, tissues, organism or communities to assess exposure-related effects of chemicals. The increasing complexity of environmental degradation requires an increase in the capacity of scientific approach in monitoring and notification as early as possible risks. Our own objective concerns the detection of aquatic environment pollution in Romania and particularly in the Danube basin. For assessing aquatic environment pollution degree or for assessing cytotoxicity or ecotoxicity of pollutants (heavy metals, nanoparticles, pesticides, etc. we developed news experimental bioassays based on the use of viability and apoptosis biomarkers of Chlorella cells by flow cytometry. Our proposed bioassays could be rapid and very sensitive tests for in laboratory aquatic risk assessment and biomonitoring.

Educación vial y movilidad en la Infancia

Directory of Open Access Journals (Sweden)

Fernando Martín Poó

Full Text Available Resumen:La motorización creciente de los desplazamientos ha convertido al ambiente urbano en un lugar cada vez más hostil para los niños y niñas, quienes se encuentran entre los grupos humanos más vulnerables del tránsito. En esta etapa del desarrollo, la educación puede ser una herramienta clave para prevenir comportamientos de riesgo y promocionar hábitos de movilidad más saludables. El presente trabajo discute algunos aspectos relacionados con la educación vial en la infancia. Se destaca la importancia de considerar los patrones de movilidad típicos de cada edad, y de promover el uso de medios de transporte más saludables, equitativos y sustentables. Se señala además la necesidad de complementar las acciones educativas con intervenciones multi-sectoriales a diferente nivel.

A rapid and inexpensive bioassay to evaluate the decontamination of organophosphates.

Science.gov (United States)

Claborn, David M; Martin-Brown, Skylar A; Sagar, Sanjay Gupta; Durham, Paul

2012-01-01

An inexpensive and rapid bioassay using adult red flour beetles was developed for use in assessing the decontamination of environments containing organophosphates and related chemicals. A decontamination protocol was developed which demonstrated that 2 to 3 applications of 5% bleach solution were required to obtain nearly complete decontamination of malathion. The bioassay was also used to screen common household cleaners as potential decontaminating agents, but only 5% bleach was effective at improving survival of insects on steel plates treated with 25% malathion. A toxic degradation product (malaoxon) was detected using gas chromatography/mass spectrophotometry; this toxin affected the decontamination efficacy and resulted in continued toxicity to the beetles until subsequent decontaminations. The bioassay provides evidence to support the use of red flour beetles as a sensitive, less expensive method for determining safety levels of environments contaminated with malathion and other toxins, and may have application in the study of chemical warfare agents.

14C sample preparation for AMS microdosing studies at Lund University using online combustion and septa-sealed vials

Science.gov (United States)

Sydoff, Marie; Stenström, Kristina

2010-04-01

The Department of Physics at Lund University is participating in a European Union project called EUMAPP (European Union Microdose AMS Partnership Programme), in which sample preparation and accelerator mass spectrometry (AMS) measurements of biological samples from microdosing studies have been made. This paper describes a simplified method of converting biological samples to solid graphite for 14C analysis with AMS. The method is based on online combustion of the samples, and reduction of CO 2 in septa-sealed vials. The septa-sealed vials and disposable materials are used to eliminate sample cross-contamination. Measurements of ANU and Ox I standards show deviations of 2% and 3%, respectively, relative to reference values. This level of accuracy is sufficient for biological samples from microdosing studies. Since the method has very few handling steps from sample to graphite, the risk of failure during the sample preparation process is minimized, making the method easy to use in routine preparation of samples.

14C sample preparation for AMS microdosing studies at Lund University using online combustion and septa-sealed vials

International Nuclear Information System (INIS)

Sydoff, Marie; Stenstroem, Kristina

2010-01-01

The Department of Physics at Lund University is participating in a European Union project called EUMAPP (European Union Microdose AMS Partnership Programme), in which sample preparation and accelerator mass spectrometry (AMS) measurements of biological samples from microdosing studies have been made. This paper describes a simplified method of converting biological samples to solid graphite for 14 C analysis with AMS. The method is based on online combustion of the samples, and reduction of CO 2 in septa-sealed vials. The septa-sealed vials and disposable materials are used to eliminate sample cross-contamination. Measurements of ANU and Ox I standards show deviations of 2% and 3%, respectively, relative to reference values. This level of accuracy is sufficient for biological samples from microdosing studies. Since the method has very few handling steps from sample to graphite, the risk of failure during the sample preparation process is minimized, making the method easy to use in routine preparation of samples.

Comparison of analysis techniques by liquid scintillation and Cerenkov Effect for {sup 40}K quantification in aqueous samples; Comparacion de las tecnicas de analisis por centelleo liquido y efecto Cerenkov para la cuantificacion {sup 40}K en muestras acuosas

Energy Technology Data Exchange (ETDEWEB)

Miranda C, L.; Davila R, J. I.; Lopez del R, H.; Mireles G, F., E-mail: lilimica20@hotmail.com [Universidad Autonoma de Zacatecas, Unidad Academica de Estudios Nucleares, Cipres No. 10, Fracc. La Penuela, 98068 Zacatecas, Zac. (Mexico)

2015-09-15

In this work the counting by liquid scintillation and Cerenkov Effect to quantify {sup 40}K in aqueous samples was used. The performance of both techniques was studied by comparing the response of three commercial liquid scintillation OptiPhase HiSafe 3, Ultima Gold Ab and OptiPhase TriSafe, the vial type and presentation conditions of the sample for counting. In liquid scintillation, the ability to form homogeneous mixtures depended on the ionic strength of the aqueous solutions. The scintillator OptiPhase HiSafe 3 showed a greater charge capacity for solutions with high ionic strength (<3.4), while the scintillator OptiSafe TriSafe no form homogeneous mixtures for solutions of ionic strength higher than 0.3. Counting efficiencies for different proportions of sample and scintillator near 100% for the scintillators OptiSafe HiSafe 3 and Ultima Gold Ab were obtained. In the counting by Cerenkov Effect, the efficiency and sensitivity depended of the vial type; polyethylene vials were more suitable for counting that the glass vials. The sample volume had not significant effect on counting efficiency, obtaining an average value of 44.8% for polyethylene vials and 37.3% for glass vials. Therefore, the liquid scintillation was more efficient and sensitive for the measurement of {sup 40}K in aqueous solutions. (Author)

Submicron polymer particles containing fluorescent semiconductor nanocrystals CdSe/ZnS for bioassays.

Science.gov (United States)

Generalova, Alla N; Sizova, Svetlana V; Zdobnova, Tatiana A; Zarifullina, Margarita M; Artemyev, Michail V; Baranov, Alexander V; Oleinikov, Vladimir A; Zubov, Vitaly P; Deyev, Sergey M

2011-02-01

This study aimed to design a panel of uniform particulate biochemical reagents and to test them in specific bioassays. These reagents are polymer particles of different sizes doped with semiconductor nanocrystals and conjugated with either full-size antibodies or recombinant mini-antibodies (4D5 scFv fragment) designed by genetic engineering approaches. A panel of highly fluorescent polymer particles (150-800 nm) were formed by embedding CdSe/ZnS nanocrystals (quantum dots) into preformed polyacrolein and poly(acrolein-co-styrene) particles. Morphology, content and fluorescence characteristics of the prepared materials were studied by laser correlation spectroscopy, spectrophotometry, optical and fluorescent microscopy and fluorimetry. The obtained fluorescent particles sensitized by anti-Yersinia pestis antibodies were used for rapid agglutination glass test suitable for screening analysis of Y. pestis antigen and for microtiter particle agglutination, which, owing to its speed and simplicity, is very beneficial for diagnostic detection of Y. pestis antigen. Recombinant 4D5 scFv antibodies designed and conjugated with polymer particles containing quantum dots provide multipoint highly specific binding with cancer marker HER2/neu on the surface of SKOV-3 cell.

Comparison of solid-phase bioassays and ecoscores to evaluate the toxicity of contaminated soils.

Science.gov (United States)

Lors, Christine; Ponge, Jean-François; Martínez Aldaya, Maite; Damidot, Denis

2010-08-01

Five bioassays (inhibition of lettuce germination and growth, earthworm mortality, inhibition of springtail population growth, avoidance by springtails) were compared, using four coke factory soils contaminated by PAHs and trace elements, before and after biotreatment. For each bioassay, several endpoints were combined in an 'ecoscore', a measure of test sensitivity. Ecoscores pooled over all tested bioassays revealed that most organisms were highly sensitive to the concentration of 3-ring PAHs. When four soils were combined, behavioural tests using the springtail Folsomia candida showed higher ecoscores, i.e. they were most sensitive to soil contamination. However, despite overall higher sensitivity of behavioural tests, which could be used for cheap and rapid assessment of soil toxicity, especially at low levels of contamination, some test endpoints were more sensitive than others, and this may differ from a soil to another, pointing to the need for a battery of bioassays when more itemized results are expected. Copyright 2010 Elsevier Ltd. All rights reserved.

Analysing traces of autoinducer-2 requires standardization of the Vibrio harveyi bioassay.

Science.gov (United States)

Vilchez, Ramiro; Lemme, André; Thiel, Verena; Schulz, Stefan; Sztajer, Helena; Wagner-Döbler, Irene

2007-01-01

Autoinducer-2 (furanosyl borate diester) is a biologically active compound whose role as a universal bacterial signalling molecule is currently under intense investigation. Because of its instability and the low concentrations of it found in biological samples, its detection relies at present on a bioassay that measures the difference in the timing of the luminescence of the Vibrio harveyi BB170 sensor strain with and without externally added AI-2. Here we systematically investigated which parameters affected the fold induction values of luminescence obtained in the bioassay and developed a modified protocol. Our experiments showed that growth and luminescence of V. harveyi BB170 are strongly influenced by trace elements. In particular, addition of Fe(3+) within a certain concentration range to the growth medium of the preinoculum culture improved the reproducibility and reduced the variance of the bioassay. In contrast, trace elements and vitamins introduced directly into the bioassay caused inhibitory effects. The initial density and luminescence of the sensor strain are very important and the values required for these parameters were defined. Borate interferes with the detection of AI-2 by giving false positive results. The response of V. harveyi BB170 to chemically synthesized AI-2 in the bioassay is nonlinear except over a very small concentration range; it is maximum over three orders of magnitude and shows inhibition above 35 microM. Based on the modified protocol, we were able to detect AI-2 in the absence of inhibitors with maximum fold induction values for the positive control (chemically synthesized AI-2) of >120 with a standard deviation of approximately 30% in a reliable and reproducible way.

El impacto de las nuevas políticas de seguridad vial sobre la conducta de los conductores

Directory of Open Access Journals (Sweden)

Jordi Tena-Sánchez

2013-04-01

Full Text Available La evidencia empírica disponible señala de manera unánime que las nuevas políticas de tráfico y seguridad vial aplicadas en España desde 2004, y en particular la introducción del carné por puntos y la reforma del Código Penal, han tenido una fuerte incidencia positiva en la reducción de la siniestralidad. De dichos resultados se deriva que las nuevas políticas han tenido también un efecto positivo sobre la conducta de los conductores, de modo que ha sido esa mejora en la conducta al volante la que finalmente se ha traducido en una reducción de la siniestralidad. No obstante, hasta el momento, los investigadores han descuidado el análisis directo de los datos sobre cumplimiento. En el presente trabajo se analizan todos los datos disponibles que ofrecen información sobre el cumplimiento de la normativa de tráfico y seguridad vial.

Insecticidal efficacy of silica nanoparticles against Rhyzopertha dominica F. and Tribolium confusum Jacquelin du Val

Directory of Open Access Journals (Sweden)

Ziaee Masumeh

2016-07-01

Full Text Available Bioassays were conducted to assess the effects of two silicon dioxide nanoparticles of Aerosil® and Nanosav against adults of Rhyzopertha dominica F. and Tribolium confusum Jacquelin du Val. Silica nanoparticles were applied at the rates of 50, 100, 200 and 300 mg · kg−1 on wheat and peeled barley. The mortality was counted after 1, 2, 3, and 7 days of exposure. Another experiment was carried out to evaluate the effect of food source on the survival of beetles after exposure to silica nanoparticles. Adults were exposed to silica nanoparticles at the rate of 0.2 mg · cm−2 for 1 and 2 days on filter paper inside plastic Petri dishes, respectively. After exposure, the initial mortality was counted and live individuals of both species were held for a week in empty glass vials or vials containing wheat and wheat flour, respectively. Silica nanoparticles have high toxicity on R. dominica and T. confusum adults. Rhyzopertha dominica was more susceptible than T. confusum. However, the mortality of both species increased with increasing concentrations and time exposed to each concentration. At low concentrations, Aerosil® was more effective than Nanosav. Silica nanoparticles were more effective in wheat grains than barley. Results indicated that the initial mortality was so high that the impact of food source on delay mortality was unclear in most cases. Silica nanoparticles were efficient against tested species and can be used effectively in a stored grain integrated pest management program.

Use of an external source (60Co) for 32P detection efficiency determination by the Cerenkov effect, in soil extracts

International Nuclear Information System (INIS)

Nascimento Filho, V.F. do.

1975-03-01

The detection of 32 P in aqueous extracts is usually made with the aid of a Geiger-Muller detector, with thin window and sample on a planchet. Presently the technique is being developed of detection of high energy beta particles emitters ( 32 P, 42 K, 86 Rb) through the Cerenkov effect, using a commercial liquid scintillation system. This technique, despite being approximately 30 times more sensitive, has the inconvenience of varying the detection efficiency, mainly for color samples (soil extracts, for instance). From this stems the need for determining the detection efficiency for each sample. The internal standardization and channels ratio methods show a series of drawbacks, mainly the non-reutilization of the samples (1st method) and statistical uncertainty for low activity samples (2nd method). The elimination of these dreawbacks can be achieved through the utilization of the external standardization method. A 60 Co source with 1,4 μCi activity has been adapted to the sample elevator of the detector system, and a comparison was made with the channels ratio method to evaluate the efficiency of 32 P detection in soil extracts (P extraction and fractionation). The external standardization method showed to be more accurate, besides being influenced to a lesser degree by high voltage variation, sample volume and vial types. In the case of large samples, it is advisable to carry out detection in vials filled up to their full capacity; in the case of small samples, the whole volume should be transferred to the vials and completed up to 9 ml for nylon vials,10 ml for glass vials and 11 to 14 ml for polyethilene vials. On the other hand, plastic vials showed higher detection efficiency than ones. As to background radiation, the lowest rates were given by nylon vials and the highest by Beckman glass vials [pt

There Is Still Room for Improvement: Presentation of a Neutral Borosilicate Glass with Improved Chemical Stability for Parenteral Packaging.

Science.gov (United States)

Boltres, Bettine; Tratzky, Stephan; Kass, Christof; Eichholz, Rainer; Naß, Peter

2016-01-01

For pharmaceutical parenteral packaging the glass compositions have always been either Type I borosilicate or Type III soda-lime glass. As both the compositions and certain chemical and physical properties are mandated by international standards, there has not been room for any changes. However, by applying only minor adjustments, a borosilicate glass was developed that showed improved chemical stability. The chemical composition is still in the range of currently used borosilicate glasses, which makes it a Type I glass according to all current pharmacopeia. A study was performed on glass vials comparing the new glass with the standard FIOLAX(®) and two other publicly available glasses. In an extraction study with water at 121 °C the new glass showed the highest chemical stability with the lowest amount of extractables. In an accelerated ageing study, which was done with water, phosphate, and carbonate buffer at 40 °C for 12 months, the new glass also proved to have the lowest amount of leachables. In this article the new glass and the results from the studies are presented, showing the reader how much of an effect can be attained with only minor adjustments if the scientific fundamentals are clear. The pharmaceutical market has been quite constant and risk-oriented due to the high impact on the safety of the patient. As any change necessitates a complicated change process, this has, in consequence, lead the industry to resist changing the parenteral primary packaging material for decades. The main glasses have either been Type I borosilicate or Type III soda-lime glass. On the other hand, a combination of improved inspection systems and the development of more sensitive biologically based drugs has elevated the standards for parental packaging materials. For example, the measurement of extractables and leachables from the packaging material steadily came into focus. In this article, a new glass is presented that still belongs to the group of Type I borosilicate

El Sistema Vial Inca y los desafíos para su conservación en tiempos modernos

OpenAIRE

Ríos Canales, Moisés

2013-01-01

El Estado peruano, a través del Ministerio de Cultura, desarrolla dentro de su política cultural una estrategia para la identificación, protección, conservación y puesta en uso social del Sistema Vial Inca, el mayor monumento de la historia americana construida por el Estado Inca en el Siglo XV.

An examination of the analysis of radiostrontiums in bioassay applications

International Nuclear Information System (INIS)

Linauskas, S.H.; Leon, J.W.

1993-05-01

Radiostrontiums are among the most radiologically significant radionuclides in the nuclear reactor environment due to their relatively high fission yield, long physical half-life, volatility and mobility in the workplace, and long retention times in tissues such as bone. Effective bioassay programs include analytical processes that consider prospective monitoring requirements provided by screening measurements, as well as the retrospective monitoring requirements provided by screening measurements following an intake. Chromatography using crown ethers as well as the use of spectrometry techniques with advanced liquid-scintillation counters or solid-state surface-barrier detectors appear to have significant benefits for Sr bioassay programs. (author). 90 refs., 2 tabs., 3 figs

An examination of the analysis of radiostrontiums in bioassay applications

Energy Technology Data Exchange (ETDEWEB)

Linauskas, S H; Leon, J W

1993-05-01

Radiostrontiums are among the most radiologically significant radionuclides in the nuclear reactor environment due to their relatively high fission yield, long physical half-life, volatility and mobility in the workplace, and long retention times in tissues such as bone. Effective bioassay programs include analytical processes that consider prospective monitoring requirements provided by screening measurements, as well as the retrospective monitoring requirements provided by screening measurements following an intake. Chromatography using crown ethers as well as the use of spectrometry techniques with advanced liquid-scintillation counters or solid-state surface-barrier detectors appear to have significant benefits for Sr bioassay programs. (author). 90 refs., 2 tabs., 3 figs.

The IMBA suite: integrated modules for bioassay analysis

Energy Technology Data Exchange (ETDEWEB)

Birchall, A.; Jarvis, N.S.; Peace, M.S.; Riddell, A.E.; Battersby, W.P

1998-07-01

The increasing complexity of models representing the biokinetic behaviour of radionuclides in the body following intake poses problems for people who are required to implement these models. The problem is exacerbated by the current paucity of suitable software. In order to remedy this situation, a collaboration between British Nuclear Fuels, Westlakes Research Institute and the National Radiological Protection Board has started with the aim of producing a suite of modules for estimating intakes and doses from bioassay measurements using the new ICRP models. Each module will have a single purpose (e.g. to calculate respiratory tract deposition) and will interface with other software using data files. The elements to be implemented initially are plutonium, uranium, caesium, iodine and tritium. It is intended to make the software available to other parties under terms yet to be decided. This paper describes the proposed suite of integrated modules for bioassay analysis, IMBA. (author)

A Bioassay System Using Bioelectric Signals from Small Fish

Science.gov (United States)

Terawaki, Mitsuru; Soh, Zu; Hirano, Akira; Tsuji, Toshio

Although the quality of tap water is generally examined using chemical assay, this method cannot be used for examination in real time. Against such a background, the technique of fish bioassay has attracted attention as an approach that enables constant monitoring of aquatic contamination. The respiratory rhythms of fish are considered an efficient indicator for the ongoing assessment of water quality, since they are sensitive to chemicals and can be indirectly measured from bioelectric signals generated by breathing. In order to judge aquatic contamination accurately, it is necessary to measure bioelectric signals from fish swimming freely as well as to stably discriminate measured signals, which vary between individuals. However, no bioassay system meeting the above requirements has yet been established. This paper proposes a bioassay system using bioelectric signals generated from small fish in free-swimming conditions. The system records signals using multiple electrodes to cover the extensive measurement range required in a free-swimming environment, and automatically discriminates changes in water quality from signal frequency components. This discrimination is achieved through an ensemble classification method using probability neural networks to solve the problem of differences between individual fish. The paper also reports on the results of related validation experiments, which showed that the proposed system was able to stably discriminate between water conditions before and after bleach exposure.

A container closure system that allows for greater recovery of radiolabeled peptide compared to the standard borosilicate glass system

International Nuclear Information System (INIS)

Leece, Alicia K.; Heidari, Pedram; Yokell, Daniel L.; Mahmood, Umar

2013-01-01

Objectives: Often peptides used in synthesis of radiopharmaceutical PET tracers are lipophilic and adhere to the walls of container closure systems (CCS) such that costly peptide and product are not fully recoverable after synthesis occurs. This investigation compares a standard United States Pharmacopeia (USP) Type I borosilicate glass CCS to a cyclic polyolefin copolymer Crystal Zenith ® (CZ) CCS, for 68 Ga-chloride and 68 Ga-DOTATOC ([ 68 Ga] Ga-DOTA-D-Phe1-Tyr3-octreotide) retention in the reaction vial after labeling. Methods: 68 Gallium labeling of DOTATOC was conducted by adding 68 Ga-chloride, 2 M HEPES (4-(2-hydroxyethyl)piperazine-1-ethanesulfonic acid) or 0.75 M sodium acetate, and 1–30 µg of DOTATOC into the CZ or glass CCS. The reaction mixture was heated for 15 min and cooled to room temperature. The crude reaction mixture was then withdrawn via syringe, for final processing. The CCS was then assayed using a dose calibrator to determine the amount of retained 68 Ga-DOTATOC. Statistical significance was assessed using an unpaired Student's t-test. Results: In all experiments (n=72) with various amounts of peptide and different buffering systems, the CZ CCS retained less activity than the glass CCS. Using 2 M HEPES and 15 µg or 30 µg of DOTATOC, the CZ CCS retained approximately 10% less of the labeled DOTATOC compared to the glass CCS (p 68 Ga-chloride. Conclusion: For applications involving the labeling of peptides such as 68 Ga-DOTATOC, the CZ CCS compared to the glass CCS, results in an improved recovery of product. - Highlights: • We examined the adhesion of 68 Ga-DOTATOC to glass and CZ CCS. • The adhesion of the 68 Ga-DOTATOC was 10% less in CZ CCS compared to glass CCS. • Overall recovery of 68 Ga-DOTATOC reaction solution is higher in CZ CCS than glass CCS. • Adhesion to the CCS is due to 68 Ga-DOTATOC, not 68 Ga-chloride

Methodology for estimation of 32P in bioassay samples by Cerenkov counting

International Nuclear Information System (INIS)

Wankhede, Sonal; Sawant, Pramilla D.; Yadav, R.K.B.; Rao, D.D.

2016-01-01

Radioactive phosphorus ( 32 P) as phosphate is used to effectively reduce bone pain in terminal cancer patients. Several hospitals in India carry out this palliative care procedure on a regular basis. Thus, production as well as synthesis of 32 P compounds has increased over the years to meet this requirement. Monitoring of radiation workers handling 32 P compounds is important for further strengthening of radiological protection program at processing facility. 32 P being a pure beta emitter (β max = 1.71 MeV, t 1/2 = 14.3 d), bioassay is the preferred individual monitoring technique. Method standardized at Bioassay Lab, Trombay, includes estimation of 32 P in urine by co-precipitation with ammonium phosphomolybdate (AMP) followed by gross beta counting. In the present study, feasibility of Cerenkov counting for detection of 32 P in bioassay samples was explored and the results obtained were compared with the gross beta counting technique

In vitro bioassays for detecting dioxin-like activity--application potentials and limits of detection, a review.

Science.gov (United States)

Eichbaum, Kathrin; Brinkmann, Markus; Buchinger, Sebastian; Reifferscheid, Georg; Hecker, Markus; Giesy, John P; Engwall, Magnus; van Bavel, Bert; Hollert, Henner

2014-07-15

Use of in vitro assays as screening tool to characterize contamination of a variety of environmental matrices has become an increasingly popular and powerful toolbox in the field of environmental toxicology. While bioassays cannot entirely substitute analytical methods such as gas chromatography-mass spectrometry (GC-MS), the increasing improvement of cell lines and standardization of bioassay procedures enhance their utility as bioanalytical pre-screening tests prior to more targeted chemical analytical investigations. Dioxin-receptor-based assays provide a holistic characterization of exposure to dioxin-like compounds (DLCs) by integrating their overall toxic potential, including potentials of unknown DLCs not detectable via e.g. GC-MS. Hence, they provide important additional information with respect to environmental risk assessment of DLCs. This review summarizes different in vitro bioassay applications for detection of DLCs and considers the comparability of bioassay and chemical analytically derived toxicity equivalents (TEQs) of different approaches and various matrices. These range from complex samples such as sediments through single reference to compound mixtures. A summary of bioassay derived detection limits (LODs) showed a number of current bioassays to be equally sensitive as chemical methodologies, but moreover revealed that most of the bioanalytical studies conducted to date did not report their LODs, which represents a limitation with regard to low potency samples. Copyright © 2014 Elsevier B.V. All rights reserved.

Development of androgen-and estrogen-responsive bioassays, members of a panel of human cell line-based highly selective steroid-responsive bioassays

NARCIS (Netherlands)

Sonneveld, E.; Jansen, H.J..; Riteco, J.A.C.; Brouwer, A.

2005-01-01

We have established highly sensitive and specific androgen and estrogen reporter cell lines which we have named AR (androgen receptor) and ERα (estrogen receptor alpha) CALUX® (Chemically Activated LUciferase eXpression), respectively. Both bioassays are member of a panel of CALUX reporter cell

Evaluation of the amount of apically extruded debris using Mtwo and ...

African Journals Online (AJOL)

In the first group, the canals were prepared using RaCe rotary in a crown-down fashion. While in the second group, the canals were instrumented using Mtwo rotary with single length technique. After the instrumentation, the vials were heated to drive off all the moisture. The glass vials were weighed again, and the weight of ...

Fluorescence-based bioassays for the detection and evaluation of food materials.

Science.gov (United States)

Nishi, Kentaro; Isobe, Shin-Ichiro; Zhu, Yun; Kiyama, Ryoiti

2015-10-13

We summarize here the recent progress in fluorescence-based bioassays for the detection and evaluation of food materials by focusing on fluorescent dyes used in bioassays and applications of these assays for food safety, quality and efficacy. Fluorescent dyes have been used in various bioassays, such as biosensing, cell assay, energy transfer-based assay, probing, protein/immunological assay and microarray/biochip assay. Among the arrays used in microarray/biochip assay, fluorescence-based microarrays/biochips, such as antibody/protein microarrays, bead/suspension arrays, capillary/sensor arrays, DNA microarrays/polymerase chain reaction (PCR)-based arrays, glycan/lectin arrays, immunoassay/enzyme-linked immunosorbent assay (ELISA)-based arrays, microfluidic chips and tissue arrays, have been developed and used for the assessment of allergy/poisoning/toxicity, contamination and efficacy/mechanism, and quality control/safety. DNA microarray assays have been used widely for food safety and quality as well as searches for active components. DNA microarray-based gene expression profiling may be useful for such purposes due to its advantages in the evaluation of pathway-based intracellular signaling in response to food materials.

Fluorescence-Based Bioassays for the Detection and Evaluation of Food Materials

Directory of Open Access Journals (Sweden)

Kentaro Nishi

2015-10-01

Full Text Available We summarize here the recent progress in fluorescence-based bioassays for the detection and evaluation of food materials by focusing on fluorescent dyes used in bioassays and applications of these assays for food safety, quality and efficacy. Fluorescent dyes have been used in various bioassays, such as biosensing, cell assay, energy transfer-based assay, probing, protein/immunological assay and microarray/biochip assay. Among the arrays used in microarray/biochip assay, fluorescence-based microarrays/biochips, such as antibody/protein microarrays, bead/suspension arrays, capillary/sensor arrays, DNA microarrays/polymerase chain reaction (PCR-based arrays, glycan/lectin arrays, immunoassay/enzyme-linked immunosorbent assay (ELISA-based arrays, microfluidic chips and tissue arrays, have been developed and used for the assessment of allergy/poisoning/toxicity, contamination and efficacy/mechanism, and quality control/safety. DNA microarray assays have been used widely for food safety and quality as well as searches for active components. DNA microarray-based gene expression profiling may be useful for such purposes due to its advantages in the evaluation of pathway-based intracellular signaling in response to food materials.

In Vitro Androgen Bioassays as a Detection Method for Designer Androgens

Directory of Open Access Journals (Sweden)

Alison K. Heather

2013-02-01

Full Text Available Androgens are the class of sex steroids responsible for male sexual characteristics, including increased muscle mass and decreased fat mass. Illicit use of androgen doping can be an attractive option for those looking to enhance sporting performance and/or physical appearance. The use of in vitro bioassays to detect androgens, especially designer or proandrogens, is becoming increasingly important in combating androgen doping associated with nutritional supplements. The nutritional sports supplement market has grown rapidly throughout the past decade. Many of these supplements contain androgens, designer androgens or proandrogens. Many designer or proandrogens cannot be detected by the standard highly-sensitive screening methods such as gas chromatography-mass spectrometry because their chemical structure is unknown. However, in vitro androgen bioassays can detect designer and proandrogens as these assays are not reliant on knowing the chemical structure but instead are based on androgen receptor activation. For these reasons, it may be advantageous to use routine androgen bioassay screening of nutraceutical samples to help curb the increasing problem of androgen doping.

Development of K-bioassay for the efficient potassium fertilization of citrus tree

Energy Technology Data Exchange (ETDEWEB)

U, Jang Kual [Cheju National University, Cheju (Korea, Republic of); Han, Hae Ryong [Cheju National University, Cheju (Korea, Republic of); Moon, Duk Young; Kim, Chang Myung; Lim, Han Cheol; Moon, Do Kyung [Cheju Citrus Research Institute, Cheju (Korea, Republic of); Song, Sung Jun [Cheju National Univerisity, Cheju (Korea, Republic of)

1994-12-31

a Similar to the {sup 42} K uptake, {sup 86} Rb uptake by the roots of Hordeum distichum grown in the hydroponic culture was negatively correlated with the concentration of K supplied previously, showing that {sup 86} Rb can be used for the K-bioassay. {sup 86} Rb having longer half life(18.86 day) than {sup 42} K(12.36 hr) allowed the use of larger number of root samples. {sup 86} Rb uptake of 3 years old Citrus unshiu Marc. grown in water culture decreased drastically with the increase of K concentration of the culture solution, thus demonstrating that the nutrition status of K for citrus trees can be diagnosed by K-bioassay using {sup 86} Rb tracer. {sup 86} Rb uptake by the excised roots of Hordeum distichum correlated with the exchangeable K in soil. The amount of exchangeable K in soil for the optimal plant growth can be determined by its relationship. {sup 42} K- and {sup 86} Rb-uptake by the Hordeum distichum roots were markedly inhibited by 5 x 10{sup -3} M KCN in the bioassay solution, indicating that uptake is metabolically controlled. There was no significant relationship between K content in citrus leaves and K concentration in the water-culture medium. It is concluded that K-bioassay is a potentially useful tool for determining of K requirement in citrus trees. (author)

Recycle Glass in Foam Glass Production

DEFF Research Database (Denmark)

Petersen, Rasmus Rosenlund; König, Jakob; Yue, Yuanzheng

The foam glass industry turn recycle glass into heat insulating building materials. The foaming process is relative insensitive to impurities in the recycle glass. It is therefore considered to play an important role in future glass recycling. We show and discuss trends of use of recycled glasses...... in foam glass industry and the supply sources and capacity of recycle glass....

'Dose per unit content' functions: A robust tool for the interpretation of bioassay data

International Nuclear Information System (INIS)

Berkovski, V.; Bonchuk, Y.; Ratia, G.

2003-01-01

The purposes of this study were to investigate the influence of the consequences of the lack of primary bioassay information and to elaborate approaches which could improve the reliability of dose assessments. The aggregated time-dependent functions 'dose per unit organ (excretion) content' z(t) have been proposed in this study as a convenient and reliable tool for bioassay. The analysis of the variation of z with changes of AMAD has demonstrated the existence of areas of the relative invariance of z, which permits the selection of one (reference) function z for the whole area of stability. Within the framework of such an approach an arbitrary set of bioassay data can be approximated by the linear combination F(t) S i E/ i z(t-t i ), whereI> F(t) function of time t, which approximates the observed bioassay time trend; t i = time shift of the acute intake i; E i effective dose, associated with the acute intake i (the two last parameters are results of the approximation procedure). (author)

{sup 14}C sample preparation for AMS microdosing studies at Lund University using online combustion and septa-sealed vials

Energy Technology Data Exchange (ETDEWEB)

Sydoff, Marie, E-mail: marie.sydoff@med.lu.s [Department of Clinical Sciences, Medical Radiation Physics, Malmo University Hospital, SE-205 02 Malmoe (Sweden); Lund University, Department of Physics, Division of Nuclear Physics, P.O. Box 118, SE-221 00 Lund (Sweden); Stenstroem, Kristina [Lund University, Department of Physics, Division of Nuclear Physics, P.O. Box 118, SE-221 00 Lund (Sweden)

2010-04-15

The Department of Physics at Lund University is participating in a European Union project called EUMAPP (European Union Microdose AMS Partnership Programme), in which sample preparation and accelerator mass spectrometry (AMS) measurements of biological samples from microdosing studies have been made. This paper describes a simplified method of converting biological samples to solid graphite for {sup 14}C analysis with AMS. The method is based on online combustion of the samples, and reduction of CO{sub 2} in septa-sealed vials. The septa-sealed vials and disposable materials are used to eliminate sample cross-contamination. Measurements of ANU and Ox I standards show deviations of 2% and 3%, respectively, relative to reference values. This level of accuracy is sufficient for biological samples from microdosing studies. Since the method has very few handling steps from sample to graphite, the risk of failure during the sample preparation process is minimized, making the method easy to use in routine preparation of samples.

Hierarchical responses to organic contaminants in aquatic ecotoxicological bioassays: from microcystins to biodegradation

OpenAIRE

Montenegro, Katia

2008-01-01

In this thesis I explore the ecotoxicological responses of aquatic organisms at different hierarchical levels to organic contaminants by means of bioassays. The bioassays use novel endpoints or approaches to elucidate the effects of exposure to contaminants and attempt to give mechanistic explanations that could be used to interpret effects at higher hierarchical scales. The sensitivity of population growth rate in the cyanobacteria species Microcystis aeruginosa to the herbicide glyp...

Issues in weighting bioassay data for use in regressions for internal dose assessments

International Nuclear Information System (INIS)

Strom, D.J.

1992-11-01

For use of bioassay data in internal dose assessment, research should be done to clarify the goal desired, the choice of method to achieve the goal, the selection of adjustable parameters, and on the ensemble of information that is available. Understanding of these issues should determine choices of weighting factors for bioassay data used in regression models. This paper provides an assessment of the relative importance of the various factors

Changes in chemical composition and bioassay assessment of ...

African Journals Online (AJOL)

Changes in chemical composition and bioassay assessment of nutritional potentials of almond fruit waste as an alternative feedstuff for livestock. ... AFW using day-old cockerels and considering performance parameters showed that treated AFW improved feed intake, body weight gain and feed conversion ratio even better ...

The use of cultivars of Raphanus sativus for cytokinin bioassay

Directory of Open Access Journals (Sweden)

Dorota Kubowicz

2013-12-01

Full Text Available Six cultivars of radish (Raphanus sativus were tested for their usefulness in radish cytokinin bioassay by the method of Letham (1971. The best cultivar was found to be 'Sopel Lodu' which responds well to both zeatin and 2iP over a wide range of concentrations. The fresh weight of cotyledons increased at most by 71.5% (if treated with zeatin or 101.0% (if treated with 2iP compared to untreated cotyledons. This cultivar is also sensitive to the partially purified cytokinin-like fraction isolated from the pine (Pinus silvestris cambial region. The cultivar 'Sopel Lodu' is therefore proposed to be a suitable plant for cytokinin bioassays.

[Investigation on pattern of quality control for Chinese materia medica based on famous-region drug and bioassay--the work reference].

Science.gov (United States)

Yan, Dan; Xiao, Xiaohe

2011-05-01

Selection and standardization of the work reference are the technical issues to be faced with in the bioassay of Chinese materia medica. Taking the bioassay of Coptis chinensis. as an example, the manufacture process of the famous-region drugs extraction was explained from the aspects of original identification, routine examination, component analysis and bioassay. The common technologies were extracted, and the selection and standardization procedures of the work reference for the bioassay of Chinese materia medica were drawn up, so as to provide technical support for constructing a new mode and method of the quality control of Chinese materia medica based on the famous-region drugs and bioassay.

Investigation of the dose rate dependency of the PAGAT gel dosimeter at low dose rates

International Nuclear Information System (INIS)

Zehtabian, M.; Faghihi, R.; Zahmatkesh, M.H.; Meigooni, A.S.; Mosleh-Shirazi, M.A.; Mehdizadeh, S.; Sina, S.; Bagheri, S.

2012-01-01

Medical physicists need dosimeters such as gel dosimeters capable of determining three-dimensional dose distributions with high spatial resolution. To date, in combination with magnetic resonance imaging (MRI), polyacrylamide gel (PAG) polymers are the most promising gel dosimetry systems. The purpose of this work was to investigate the dose rate dependency of the PAGAT gel dosimeter at low dose rates. The gel dosimeter was used for measurement of the dose distribution around a Cs-137 source from a brachytherapy LDR source to have a range of dose rates from 0.97 Gy h −1 to 0.06 Gy h −1 . After irradiation of the PAGAT gel, it was observed that the dose measured by gel dosimetry was almost the same at different distances (different dose rates) from the source, although the points nearer the source had been expected to receive greater doses. Therefore, it was suspected that the PAGAT gel is dose rate dependent at low dose rates. To test this further, three other sets of measurements were performed by placing vials containing gel at different distances from a Cs-137 source. In the first two measurements, several plastic vials were exposed to equal doses at different dose rates. An ionization chamber was used to measure the dose rate at each distance. In addition, three TLD chips were simultaneously irradiated in order to verify the dose to each vial. In the third measurement, to test the oxygen diffusion through plastic vials, the experiment was repeated again using plastic vials in a nitrogen box and glass vials. The study indicates that oxygen diffusion through plastic vials for dose rates lower than 2 Gy h −1 would affect the gel dosimeter response and it is suggested that the plastic vials or (phantoms) in an oxygen free environment or glass vials should be used for the dosimetry of low dose rate sources using PAGAT gel to avoid oxygen diffusion through the vials.

Natural products phytotoxicity A bioassay suitable for small quantities of slightly water-soluble compounds.

Science.gov (United States)

Dornbos, D L; Spencer, G F

1990-02-01

A large variety of secondary metabolites that can inhibit germination and/or seedling growth are produced by plants in low quantities. The objective of this study was to develop a bioassay capable of reliably assessing reductions in germination percentage and seedling length of small-seeded plant species caused by exposure to minute quantities of these compounds. The germination and growth of alfalfa (Medicago saliva), annual ryegrass (Lolium multiflorum), and velvetleaf (Abutilon theophrasti) were evaluated against six known phytotoxins from five chemical classes; cinmethylin (a herbicidal cineole derivative) was selected as a comparison standard. Each phytotoxin, dissolved in a suitable organic solvent, was placed on water-agar in small tissue culture wells. After the solvent evaporated, imbibed seeds were placed on the agar; after three days, germination percentages and seedling lengths were measured. Compared to a commonly used filter paper procedure, this modified agar bioassay required smaller quantities of compound per seed for comparable bioassay results. This bioassay also readily permitted the measurement of seedling length, a more sensitive indicator of phytotoxicity than germination. Seedling length decreased sigmoidally as the toxin concentration increased logarithmically. Phytotoxicity was a function of both compound and plant species. Cinmethylin, a grass herbicide, reduced the length of annual ryegrass seedlings by 90-100%, whereas that of alfalfa and velvetleaf was inhibited slightly. The agar bioassay facilitated the rapid and reliable testing of slightly water-soluble compounds, requiring only minute quantities of each compound to give reproducible results.

The Intersection of CMOS Microsystems and Upconversion Nanoparticles for Luminescence Bioimaging and Bioassays

Directory of Open Access Journals (Sweden)

Liping Wei

2014-09-01

Full Text Available Organic fluorophores and quantum dots are ubiquitous as contrast agents for bio-imaging and as labels in bioassays to enable the detection of biological targets and processes. Upconversion nanoparticles (UCNPs offer a different set of opportunities as labels in bioassays and for bioimaging. UCNPs are excited at near-infrared (NIR wavelengths where biological molecules are optically transparent, and their luminesce in the visible and ultraviolet (UV wavelength range is suitable for detection using complementary metal-oxide-semiconductor (CMOS technology. These nanoparticles provide multiple sharp emission bands, long lifetimes, tunable emission, high photostability, and low cytotoxicity, which render them particularly useful for bio-imaging applications and multiplexed bioassays. This paper surveys several key concepts surrounding upconversion nanoparticles and the systems that detect and process the corresponding luminescence signals. The principle of photon upconversion, tuning of emission wavelengths, UCNP bioassays, and UCNP time-resolved techniques are described. Electronic readout systems for signal detection and processing suitable for UCNP luminescence using CMOS technology are discussed. This includes recent progress in miniaturized detectors, integrated spectral sensing, and high-precision time-domain circuits. Emphasis is placed on the physical attributes of UCNPs that map strongly to the technical features that CMOS devices excel in delivering, exploring the interoperability between the two technologies.

Development of Androgen- and Estrogen-Responsive bio-assays, members of a panel of human cell line-based highly selective steroid-responsive bioassays

NARCIS (Netherlands)

Sonneveld, E.; Jansen, H.J.

2004-01-01

We have established highly sensitive and specific androgen and estrogen reporter cell lines which we have named AR (androgen receptor) and ERα (estrogen receptor alpha) CALUX® (Chemically Activated LUciferase eXpression), respectively. Both bioassays are member of a panel of CALUX reporter cell

Toxicity of hydrogen sulfide to goldfish (Carassius auratus L. ) as influenced by temperature, oxygen, and bioassay techniques

Energy Technology Data Exchange (ETDEWEB)

Adelman, I.R.; Smith, L.L. Jr.

1972-01-01

Bioassays were conducted to test the effect of temperature and oxygen on H/sub 2/S toxicity to goldfish (Carassius auratus L.) and to investigate some factors that influence bioassay results. Relation of H/sub 2/S toxicity to temperature is negatively logarithmic over the range of 6.5-25 C. The mean 96-hr TL50 at 6 C was 530 ..mu..g/liter and at 25 C was 4 ..mu..g/liter. At temperatures of 14, 20, and 26 C, most acute mortality from H/sub 2/S ended by 11 days and the 11-day TL50's at these temperatures were significantly different. In bioassays with and without prior oxygen acclimation, decreasing oxygen concentrations increased H/sub 2/S toxicity. In the former, mean TL50's were 62 and 48 ..mu..g/liter H/sub 2/S at oxygen concentrations of 6 and 1.5 mg/liter, respectively, and in the latter, 71 and 53 ..mu..g/liter H/sub 2/S at the same oxygen concentrations. Variability in bioassay results was not affected by test temperatures of 14, 20, and 26 C, and in most cases 1 week of temperature acclimation was adequate. Stocks of fish responded differently after 11 days of bioassay, although differences were not detected after 4 days of bioassay. 27 references, 4 figures, 3 tables.

Stability of 10 mg/mL cefuroxime solution for intracameral injection in commonly used polypropylene syringes and new ready-to-use cyclic olefin copolymer sterile vials using the LC-UV stability-indicating method.

Science.gov (United States)

Feutry, Frédéric; Simon, Nicolas; Genay, Stéphanie; Lannoy, Damien; Barthélémy, Christine; Décaudin, Bertrand; Labalette, Pierre; Odou, Pascal

2016-01-01

Injecting intracameral cefuroxime has been found beneficial in reducing the risk of postoperative endophthalmitis but its use has been limited through a lack of approved marketing and of ready-to-use single-units as well as the problem of aseptic compounding. Our aim was to assess a new automated primary packaging system which should ensure a higher level of sterility, thanks to its closed, sterile, ready-to-use polymer vial called "Crystal® vial". The chemical stability of a 10 mg/mL cefuroxime solution was compared in 1 mL Crystal® vials and 1 mL Luer-lock polypropylene syringes (actual reference) to eliminate any potential and specific interactions with its cyclic olefin copolymer (COC) body and elastomer stopper. Cefuroxime solution was introduced into vials and syringes and stored at -20 °C, +5 °C and +25°C/60% Relative Humidity. Cefuroxime concentration and the relative amount of the main degradation product (descarbamoyl-cefuroxime) were both determined by an HPLC/UV method indicating stability. Solutions were considered steady if the concentration remained at over 90% of the initial value. In the adapted storage conditions, the evolution of osmolality, pH and sterility was assessed. Stability profiles were identical between vials and syringes in all storage and temperature conditions. The solution was stable (cefuroxime concentration, pH and osmolality) and still sterile for 365 days at -20°C. The concentration fell below 90% after 21 days at +5 °C and after 16 h at +25°C/60%s relative humidity. The COC and thermoplastic elastomer of the vials had no impact on the degradation process confirming its possible use for a ready-to-use cefuroxime solution single-unit dose.

Urine sample collection protocols for bioassay samples

Energy Technology Data Exchange (ETDEWEB)

MacLellan, J.A.; McFadden, K.M.

1992-11-01

In vitro radiobioassay analyses are used to measure the amount of radioactive material excreted by personnel exposed to the potential intake of radioactive material. The analytical results are then used with various metabolic models to estimate the amount of radioactive material in the subject`s body and the original intake of radioactive material. Proper application of these metabolic models requires knowledge of the excretion period. It is normal practice to design the bioassay program based on a 24-hour excretion sample. The Hanford bioassay program simulates a total 24-hour urine excretion sample with urine collection periods lasting from one-half hour before retiring to one-half hour after rising on two consecutive days. Urine passed during the specified periods is collected in three 1-L bottles. Because the daily excretion volume given in Publication 23 of the International Commission on Radiological Protection (ICRP 1975, p. 354) for Reference Man is 1.4 L, it was proposed to use only two 1-L bottles as a cost-saving measure. This raised the broader question of what should be the design capacity of a 24-hour urine sample kit.

Urine sample collection protocols for bioassay samples

Energy Technology Data Exchange (ETDEWEB)

MacLellan, J.A.; McFadden, K.M.

1992-11-01

In vitro radiobioassay analyses are used to measure the amount of radioactive material excreted by personnel exposed to the potential intake of radioactive material. The analytical results are then used with various metabolic models to estimate the amount of radioactive material in the subject's body and the original intake of radioactive material. Proper application of these metabolic models requires knowledge of the excretion period. It is normal practice to design the bioassay program based on a 24-hour excretion sample. The Hanford bioassay program simulates a total 24-hour urine excretion sample with urine collection periods lasting from one-half hour before retiring to one-half hour after rising on two consecutive days. Urine passed during the specified periods is collected in three 1-L bottles. Because the daily excretion volume given in Publication 23 of the International Commission on Radiological Protection (ICRP 1975, p. 354) for Reference Man is 1.4 L, it was proposed to use only two 1-L bottles as a cost-saving measure. This raised the broader question of what should be the design capacity of a 24-hour urine sample kit.

The application of bioassays as indicators of petroleum-contaminated soil remediation.

Science.gov (United States)

Płaza, Grazyna; Nałecz-Jawecki, Grzegorz; Ulfig, Krzysztof; Brigmon, Robin L

2005-04-01

Bioremediation has proven successful in numerous applications to petroleum contaminated soils. However, questions remain as to the efficiency of bioremediation in lowering long-term soil toxicity. In the present study, the bioassays Spirotox, Microtox, Ostracodtoxkit F, umu-test with S-9 activation, and plant assays were applied, and compared to evaluate bioremediation processes in heavily petroleum contaminated soils. Six higher plant species (Secale cereale L., Lactuca sativa L., Zea mays L., Lepidium sativum L., Triticum vulgare L., Brassica oleracea L.) were used for bioassay tests based on seed germination and root elongation. The ecotoxicological analyses were made in DMSO/H2O and DCM/DMSO soil extracts. Soils were tested from two biopiles at the Czechowice oil refinery, Poland, that have been subjected to different bioremediation applications. In biopile 1 the active or engineered bioremediation process lasted four years, while biopile 2 was treated passively or non-engineered for eight months. The test species demonstrated varying sensitivity to soils from both biopiles. The effects on test organisms exposed to biopile 2 soils were several times higher compared to those in biopile 1 soils, which correlated with the soil contaminants concentration. Soil hydrocarbon concentrations indeed decreased an average of 81% in biopile 1, whereas in biopile 2 TPH/TPOC concentrations only decreased by 30% after eight months of bioremediation. The bioassays were presented to be sensitive indicators of soil quality and can be used to evaluate the quality of bioremediated soil. The study encourages the need to combine the bioassays with chemical monitoring for evaluation of the bioremediation effectiveness and assessing of the contaminated/remediated soils.

Glass consistency and glass performance

International Nuclear Information System (INIS)

Plodinec, M.J.; Ramsey, W.G.

1994-01-01

Glass produced by the Defense Waste Processing Facility (DWPF) will have to consistently be more durable than a benchmark glass (evaluated using a short-term leach test), with high confidence. The DWPF has developed a Glass Product Control Program to comply with this specification. However, it is not clear what relevance product consistency has on long-term glass performance. In this report, the authors show that DWPF glass, produced in compliance with this specification, can be expected to effectively limit the release of soluble radionuclides to natural environments. However, the release of insoluble radionuclides to the environment will be limited by their solubility, and not glass durability

Aplicación de los Sistemas de Información Geográfica para la gestión de la malla vial de la ciudad de Medellín

Directory of Open Access Journals (Sweden)

Jaime A. Zapata Duque

2012-12-01

Full Text Available El estado de la malla vial depende fundamentalmente de factores tales como el tráfico, características estructurales y funcionales del pavimento y condiciones climatológicas locales, y su mantenimiento tiene importantes implicaciones espaciales. Este documento describe el proceso de implementación del sistema de gestión de pavimentos de la ciudad de Medellín, desarrollado en una plataforma SIG. El sistema está soportado en una geodatabase corporativa de inventario y diagnóstico, el cual alimenta un software de modelación del deterioro del pavimento y arroja recomendaciones de intervención en cada segmento vial. Este sistema sirve como apoyo a las autoridades encargadas a la toma de decisiones, con el fin de realizar la planeación del mantenimiento de la malla vial, optimizar los recursos disponibles y ofrecer un mejor servicio a la comunidad.

Resolutions of ICRP models with BIOKMOD: Application for the bioassays evaluation

International Nuclear Information System (INIS)

Sanchez, G.

2005-01-01

Biokmod is a tool box developed using Mathematic for solving compartmental modes. It gives analytic and numeric solutions. Biokmod solves the current ICRP models including Acute, constant, continuous variable, multi-inputs and random intakes. All parameters (deposition factors, rate transfer coefficients, fractional rate of absorption, etc.) can be modified by users. It can be also applied for evaluating unknown intakes fitting bioassay experimental data and for evacuating uncertainties in the ICRP models. There is a web version (BiokmodWeb) at http://www3.enusa.es//webMathematica/public/biokmode.html. In this article we describe the application of Biokmod for evaluating Bioassays. (Author) 8 refs

Requirements for radiation emergency urine bioassay techniques for the public and first responders.

Science.gov (United States)

Li, Chunsheng; Vlahovich, Slavica; Dai, Xiongxin; Richardson, Richard B; Daka, Joseph N; Kramer, Gary H

2010-11-01

Following a radiation emergency, the affected public and the first responders may need to be quickly assessed for internal contamination by the radionuclides involved. Urine bioassay is one of the most commonly used methods for assessing radionuclide intake and radiation dose. This paper attempts to derive the sensitivity requirements (from inhalation exposure) for the urine bioassay techniques for the top 10 high-risk radionuclides that might be used in a terrorist attack. The requirements are based on a proposed reference dose to adults of 0.1 Sv (CED, committed effective dose). In addition, requirements related to sample turnaround time and field deployability of the assay techniques are also discussed. A review of currently available assay techniques summarized in this paper reveals that method development for ²⁴¹Am, ²²⁶Ra, ²³⁸Pu, and ⁹⁰Sr urine bioassay is needed.

A Shandon PapSpin liquid-based gynecological test: A split-sample and direct-to-vial test with histology follow-up study

Directory of Open Access Journals (Sweden)

Rimiene J

2010-01-01

Full Text Available Background: Studies for liquid-based Papanicolaou (Pap tests reveal that liquid-based cytology (LBC is a safe and effective alternative to the conventional Pap smear. Although there is research on ThinPrep and SurePath systems, information is lacking to evaluate the efficiency and effectiveness of systems based on cytocentrifugation. This study is designed to determine the sensitivity and specificity of the Shandon PapSpin (ThermoShandon, Pittsburgh, Pennsylvania, USA liquid-based gynecological system. We used split-sample and direct-to-vial study design. Materials and Methods: 2,945 women referred to prophylactic check-up were enrolled in this study. Split sample design was used in 1,500 women and residual cervical cytology specimen from all these cases was placed in fluid for PapSpin preparation after performing conventional smear. The direct-to-vial study was carried out in another cohort of 1,445 women in whom the entire cervical material was investigated using only the PapSpin technique. Follow up histological diagnoses for 141 women were obtained from both study arms following 189 abnormal cytology cases. 80 LBC cases from the split sample group and 61 LBC cases in the direct-to-vial group were correlated with the histology results. The sensitivity and secificity of the conventional smear and PapSpin tests in both study arms were compared. Results: In the split sample group, conventional smears showed a higher proportion of ASC-US (atypical cells undetermined significance: 31 (2.1% vs 10 (0.7% in PapSpin (P = 0.001. A higher proportion of unsatisfactory samples was found in the conventional smear group: 25 (1.7% vs 6 (0.4% cases (P = 0.001. In the split sample group, the sensitivity of the conventional and PapSpin tests was 68.7% vs 78.1%, and the specificity 93.8% vs 91.8%, respectively. In the direct to vial group PapSpin sensitivity was 75.9% and specificity 96.5%. The differences in sensitivity and specificity were not significant. The

Responses of lone star tick (acari: ixodidae) nymphs to the repellent deet applied in acetone and ethanol solutions in vitro bioassays

Science.gov (United States)

Behavioral bioassays remain a standard tool in the discovery, development, and registration of repellents. Although tick repellent bioassays tend to be rather uncomplicated, several factors can influence their outcomes. Typically repellent bioassays use a solvent, such as acetone or ethanol, to disp...

Preliminary results of testing bioassay analytical performance standards

International Nuclear Information System (INIS)

Fisher, D.R.; Robinson, A.V.; Hadley, R.T.

1983-08-01

The analytical performance of both in vivo and in vitro bioassay laboratories is being studied to determine the capability of these laboratories to meet the minimum criteria for accuracy and precision specified in the draft ANSI Standard N13.30, Performance Criteria for Radiobioassay. This paper presents preliminary results of the first round of testing

Correction factors of commercial radionuclide calibrators for several measurement geometries of radiopharmaceuticals

International Nuclear Information System (INIS)

Correia, Amanda Ribeiro

2011-01-01

In order to reach therapy and diagnosis objectives, the activity must be determined with high accuracy to administer a radiopharmaceutical to a patient. Initially, a glass vial with the radiopharmaceutical is placed into the radionuclide calibrator to determine its activity. Subsequently, an aliquot is transferred to a syringe and again its activity is measured on the calibrator before being administered to the patient. The glass vial and the syringe are different in many aspects as the calibration factors too, which may cause incorrect activities administered to the patient. This study aims to determine the correction factors, as well as the values of the uncertainties associated to two distinct models of calibrators: one that uses ionization chamber and another Geiger-Mueller as detectors. The radionuclides chosen were 99 Tc m and 123 1 and the containers were glass vials (type lOR and P6) and plastic syringes of 3 and 5 mL. The correction factors for each type of vials or syringe were determined as a function of volume and type of calibrator. Activity measurements comparison was also made involving several radionuclide calibrators of different models belonging to four nuclear medicine hospitals and to National Metrology Laboratory of lionizing Radiation (LNMRI). In the measurements of activity values larger than allowed by CNEN NN-3.05 norm, results have shown deviations for syringes in calibrator with Geiger-Mueller detectors and for both radionuclides. (author)

Progress in herbicide determination with the thylakoid bioassay.

Science.gov (United States)

Trapmann, S; Etxebarria, N; Schnabl, H; Grobecker, K H

1998-01-01

Chloroplast thylakoids are used as biological units to determine herbicides in different kinds of water samples as well as in aqueous extracts of compost, soil or food samples. The thylakoid bioassay shows clearly inhibition of fluorescence yield in the presence of photosystem II specific herbicides. Due to this method the ecotoxicological effect of samples with unknown pollutants can be tested fast and cost effective. It has been proven that all photosynthetic active compounds are recorded at the same time because only additive interactions occur. Therefore, the contamination level can be expressed as cumulative parameter for photosystem II active substances. Application was improved clearly by the addition of the radical scavenger sodium ascorbate to the isolation media and by a higher concentration of the measuring medium. A new data evaluation method is described yielding in a lower detection limit of 0.4 microg diuron/1. The guidelines for the quality of water for human consumption with an allowable concentration of pesticides in groups is 0,5 microg/1 and can be controlled with the thylakoid bioassay without performing any preconcentration steps.

Androgen Bioassay for the Detection of Nonlabeled Androgenic Compounds in Nutritional Supplements.

Science.gov (United States)

Cooper, Elliot R; McGrath, Kristine C Y; Li, XiaoHong; Heather, Alison K

2018-01-01

Both athletes and the general population use nutritional supplements. Athletes often turn to supplements hoping that consuming the supplement will help them be more competitive and healthy, while the general population hopes to improve body image or vitality. While many supplements contain ingredients that may have useful properties, there are supplements that are contaminated with compounds that are banned for use in sport or have been deliberately adulterated to fortify a supplement with an ingredient that will produce the advertised effect. In the present study, we have used yeast cell and mammalian cell androgen bioassays to characterize the androgenic bioactivity of 112 sports supplements available from the Australian market, either over the counter or via the Internet. All 112 products did not declare an androgen on the label as an included ingredient. Our findings show that six out of 112 supplements had strong androgenic bioactivity in the yeast cell bioassay, indicating products spiked or contaminated with androgens. The mammalian cell bioassay confirmed the strong androgenic bioactivity of five out of six positive supplements. Supplement 6 was metabolized to weaker androgenic bioactivity in the mammalian cells. Further to this, Supplement 6 was positive in a yeast cell progestin bioassay. Together, these findings highlight that nutritional supplements, taken without medical supervision, could expose or predispose users to the adverse consequences of androgen abuse. The findings reinforce the need to increase awareness of the dangers of nutritional supplements and highlight the challenges that clinicians face in the fast-growing market of nutritional supplements.

Application of the CALUX bioassay for epidemiological study. Analyses of Belgian human plasma

Energy Technology Data Exchange (ETDEWEB)

Wouwe, N. van; Debacker, N.; Sasse, A. [Scientific Institute of Public Health, Brussels (BE)] (and others)

2004-09-15

The CALUX bioassay is a promising screening method for the detection of dioxin-like compounds. The observed good sensitivity, low number of false negative results as well as the good correlations with the GC-HRMS TEQ-values in case of feed and food analyses allow this method to climb in the first assessment methods' scale. The low amount of sample needed in addition to those latest advantages suggest that the CALUX bioassay could be a good screening method for epidemiological studies. The Belgian epidemiological study concerning the possible effect of the dioxin incident on the body burden of the Belgian population was an opportunity to test this method in comparison to the gold reference one: the GC-HRMS. The first part of this abstract presents epidemiological parameters (sensibility, specificity,) of the CALUX bioassay using CALUX TEQ-values as estimators of the TEQ-values of the 17 PCDD/Fs. The second part examines epidemiological determinants observed for CALUX and GCHRMS TEQ-values.

Assessing the genotoxicity of urban air pollutants using two in situ plant bioassays

Energy Technology Data Exchange (ETDEWEB)

Villarini, M.; Fatigoni, C.; Dominici, L.; Maestri, S. [Department of Medical-Surgical Specialties and Public Health, University of Perugia, I-06126 (Italy); Ederli, L.; Pasqualini, S. [Department of Applied Biology, University of Perugia, I-06121 (Italy); Monarca, S. [Department of Medical-Surgical Specialties and Public Health, University of Perugia, I-06126 (Italy); Moretti, M., E-mail: massimo.moretti@unipg.i [Department of Medical-Surgical Specialties and Public Health, University of Perugia, I-06126 (Italy)

2009-12-15

Genotoxicity of urban air has been analysed almost exclusively in airborne particulates. We monitored the genotoxic effects of airborne pollutants in the urban air of Perugia (Central Italy). Two plant bioindicators with different genetic endpoints were used: micronuclei in meiotic pollen mother cells using Tradescantia-micronucleus bioassay (Trad-MCN) and DNA damage in nuclei of Nicotiana tabacum leaves using comet assay (Nicotiana-comet). Buds of Tradescantia clone no. 4430 and young N. tabacum cv. Xanthi plants were exposed for 24 h at three sites with different pollution levels. One control site (indoor control) was also used. The two bioassays showed different sensitivities toward urban pollutants: Trad-MCN assay was the most sensitive, but DNA damage in N. tabacum showed a better correlation with the pollutant concentrations. In situ biomonitoring of airborne genotoxins using higher plants combined with chemical analysis is thus recommended for characterizing genotoxicity of urban air. - Plant bioassays used to explore in situ the correlation between air pollution and genotoxicity.

Assessing the genotoxicity of urban air pollutants using two in situ plant bioassays

International Nuclear Information System (INIS)

Villarini, M.; Fatigoni, C.; Dominici, L.; Maestri, S.; Ederli, L.; Pasqualini, S.; Monarca, S.; Moretti, M.

2009-01-01

Genotoxicity of urban air has been analysed almost exclusively in airborne particulates. We monitored the genotoxic effects of airborne pollutants in the urban air of Perugia (Central Italy). Two plant bioindicators with different genetic endpoints were used: micronuclei in meiotic pollen mother cells using Tradescantia-micronucleus bioassay (Trad-MCN) and DNA damage in nuclei of Nicotiana tabacum leaves using comet assay (Nicotiana-comet). Buds of Tradescantia clone no. 4430 and young N. tabacum cv. Xanthi plants were exposed for 24 h at three sites with different pollution levels. One control site (indoor control) was also used. The two bioassays showed different sensitivities toward urban pollutants: Trad-MCN assay was the most sensitive, but DNA damage in N. tabacum showed a better correlation with the pollutant concentrations. In situ biomonitoring of airborne genotoxins using higher plants combined with chemical analysis is thus recommended for characterizing genotoxicity of urban air. - Plant bioassays used to explore in situ the correlation between air pollution and genotoxicity.

Impact of Spodoptera frugiperda neonate pretreatment conditions on Vip3Aa19 insecticidal protein activity and laboratory bioassay variation.

Science.gov (United States)

Da Silva, Karen F; Spencer, Terence A; Camargo Gil, Carolina; Siegfried, Blair D; Walters, Frederick S

2016-04-01

Variation in response to insecticidal proteins is common upon repetition of insect bioassays. Understanding this variation is a prerequisite to detecting biologically important differences. We tracked neonate Spodoptera frugiperda (J.E. Smith) susceptibility to Vip3Aa19 over 17 generations using standardized bioassay methods. Five larval pretreatment conditions and one bioassay condition were tested to determine whether susceptibility was affected. These included: storage time; prefeeding; storage at reduced temperature; storage at reduced humidity; colony introgression of field-collected individuals. Extremes of photoperiod during the bioassay itself were also examined. LC50 values for two strains of S. frugiperda varied 6.6-fold or 8.8-fold over 17 generations. Storage time and humidity had no impact on Vip3Aa19 susceptibility, whereas prefeeding significantly reduced subsequent mortality (by 27%). Storage at reduced temperature increased mortality for one colony (from 45.6 to 73.0%) but not for the other. Introgression of field-collected individuals affected susceptibility at the first generation but not for subsequent generations. A 24 h bioassay photophase significantly reduced susceptibility (by 26%) for both colonies. Certain pretreatment and bioassay conditions were identified that can affect S. frugiperda Vip3Aa19 susceptibility, but innate larval heterogeneity was also present. Our observations should help to increase the consistency of insecticidal protein bioassay results. © 2015 Syngenta Crop Protection, LLC. Pest Management Science published by John Wiley & Sons Ltd on behalf of Society of Chemical Industry.

Development of bacteria-based bioassays for arsenic detection in natural waters.

Science.gov (United States)

Diesel, Elizabeth; Schreiber, Madeline; van der Meer, Jan Roelof

2009-06-01

Arsenic contamination of natural waters is a worldwide concern, as the drinking water supplies for large populations can have high concentrations of arsenic. Traditional techniques to detect arsenic in natural water samples can be costly and time-consuming; therefore, robust and inexpensive methods to detect arsenic in water are highly desirable. Additionally, methods for detecting arsenic in the field have been greatly sought after. This article focuses on the use of bacteria-based assays as an emerging method that is both robust and inexpensive for the detection of arsenic in groundwater both in the field and in the laboratory. The arsenic detection elements in bacteria-based bioassays are biosensor-reporter strains; genetically modified strains of, e.g., Escherichia coli, Bacillus subtilis, Staphylococcus aureus, and Rhodopseudomonas palustris. In response to the presence of arsenic, such bacteria produce a reporter protein, the amount or activity of which is measured in the bioassay. Some of these bacterial biosensor-reporters have been successfully utilized for comparative in-field analyses through the use of simple solution-based assays, but future methods may concentrate on miniaturization using fiberoptics or microfluidics platforms. Additionally, there are other potential emerging bioassays for the detection of arsenic in natural waters including nematodes and clams.

Development of bacteria-based bioassays for arsenic detection in natural waters

Energy Technology Data Exchange (ETDEWEB)

Diesel, Elizabeth; Schreiber, Madeline [Virginia Tech, Department of Geosciences, Blacksburg, VA (United States); Meer, Jan Roelof van der [University of Lausanne, Department of Fundamental Microbiology, Lausanne (Switzerland)

2009-06-15

Arsenic contamination of natural waters is a worldwide concern, as the drinking water supplies for large populations can have high concentrations of arsenic. Traditional techniques to detect arsenic in natural water samples can be costly and time-consuming; therefore, robust and inexpensive methods to detect arsenic in water are highly desirable. Additionally, methods for detecting arsenic in the field have been greatly sought after. This article focuses on the use of bacteria-based assays as an emerging method that is both robust and inexpensive for the detection of arsenic in groundwater both in the field and in the laboratory. The arsenic detection elements in bacteria-based bioassays are biosensor-reporter strains; genetically modified strains of, e.g., Escherichia coli, Bacillus subtilis, Staphylococcus aureus, and Rhodopseudomonas palustris. In response to the presence of arsenic, such bacteria produce a reporter protein, the amount or activity of which is measured in the bioassay. Some of these bacterial biosensor-reporters have been successfully utilized for comparative in-field analyses through the use of simple solution-based assays, but future methods may concentrate on miniaturization using fiberoptics or microfluidics platforms. Additionally, there are other potential emerging bioassays for the detection of arsenic in natural waters including nematodes and clams. (orig.)

Bioassay of procoagulant albumin in human plasma.

Science.gov (United States)

Grosset, A; Liu, L; Parker, C J; Rodgers, G M

1994-09-01

Procoagulant albumin (P-Al) is present in normal human plasma and increases monocyte and endothelial cell expression of tissue factor activity. To develop a bioassay for P-Al, we partially purified plasma from healthy volunteers and several patient groups using BaCl2 and (NH4)2SO4 precipitation. The samples were assayed for tissue factor (TF) inducing activity, expressed as a percentage increase compared to a serum-free media control. Over six months, the assay was reproducible in stored samples and in serial samples from normal volunteers. The plasma P-Al activities of 35 volunteers averaged 141 +/- 8.2% (SEM). There was no diurnal variation. There was no difference in the P-Al activity after a 12 hour fast and 2 hours after a large meal in 4 healthy volunteers. There was no increase in activity (r = 0.16) with the subject's age. The average activity from 16 poorly-controlled diabetics was 131 +/- 11% (SEM). No alteration in activity was seen with samples from patients with uremia, liver dysfunction, hemophilia, thrombotic events, or adenocarcinoma. These results indicate that P-Al activity can be bioassayed in individual patient samples; however, pathologic states associated with abnormal P-Al-induced tissue factor activity presently remain unidentified.

A Rapid and Simple Bioassay Method for Herbicide Detection

Directory of Open Access Journals (Sweden)

Xiu-Qing Li

2008-01-01

Full Text Available Chlamydomonas reinhardtii, a unicellular green alga, has been used in bioassay detection of a variety of toxic compounds such as pesticides and toxic metals, but mainly using liquid culture systems. In this study, an algal lawn--agar system for semi-quantitative bioassay of herbicidal activities has been developed. Sixteen different herbicides belonging to 11 different categories were applied to paper disks and placed on green alga lawns in Petri dishes. Presence of herbicide activities was indicated by clearing zones around the paper disks on the lawn 2-3 days after application. The different groups of herbicides induced clearing zones of variable size that depended on the amount, mode of action, and chemical properties of the herbicides applied to the paper disks. This simple, paper-disk-algal system may be used to detect the presence of herbicides in water samples and act as a quick and inexpensive semi-quantitative screening for assessing herbicide contamination.

DWPF GLASS BEADS AND GLASS FRIT TRANSPORT DEMONSTRATION

Energy Technology Data Exchange (ETDEWEB)

Adamson, D; Bradley Pickenheim, B

2008-11-24

DWPF is considering replacing irregularly shaped glass frit with spherical glass beads in the Slurry Mix Evaporator (SME) process to decrease the yield stress of the melter feed (a non-Newtonian Bingham Plastic). Pilot-scale testing was conducted on spherical glass beads and glass frit to determine how well the glass beads would transfer when compared to the glass frit. Process Engineering Development designed and constructed the test apparatus to aid in the understanding and impacts that spherical glass beads may have on the existing DWPF Frit Transfer System. Testing was conducted to determine if the lines would plug with the glass beads and the glass frit slurry and what is required to unplug the lines. The flow loop consisted of vertical and horizontal runs of clear PVC piping, similar in geometry to the existing system. Two different batches of glass slurry were tested: a batch of 50 wt% spherical glass beads and a batch of 50 wt% glass frit in process water. No chemicals such as formic acid was used in slurry, only water and glass formers. The glass beads used for this testing were commercially available borosilicate glass of mesh size -100+200. The glass frit was Frit 418 obtained from DWPF and is nominally -45+200 mesh. The spherical glass beads did not have a negative impact on the frit transfer system. The transferring of the spherical glass beads was much easier than the glass frit. It was difficult to create a plug with glass bead slurry in the pilot transfer system. When a small plug occurred from setting overnight with the spherical glass beads, the plug was easy to displace using only the pump. In the case of creating a man made plug in a vertical line, by filling the line with spherical glass beads and allowing the slurry to settle for days, the plug was easy to remove by using flush water. The glass frit proved to be much more difficult to transfer when compared to the spherical glass beads. The glass frit impacted the transfer system to the point

DWPF GLASS BEADS AND GLASS FRIT TRANSPORT DEMONSTRATION

International Nuclear Information System (INIS)

Adamson, D.; Pickenheim, Bradley

2008-01-01

DWPF is considering replacing irregularly shaped glass frit with spherical glass beads in the Slurry Mix Evaporator (SME) process to decrease the yield stress of the melter feed (a non-Newtonian Bingham Plastic). Pilot-scale testing was conducted on spherical glass beads and glass frit to determine how well the glass beads would transfer when compared to the glass frit. Process Engineering Development designed and constructed the test apparatus to aid in the understanding and impacts that spherical glass beads may have on the existing DWPF Frit Transfer System. Testing was conducted to determine if the lines would plug with the glass beads and the glass frit slurry and what is required to unplug the lines. The flow loop consisted of vertical and horizontal runs of clear PVC piping, similar in geometry to the existing system. Two different batches of glass slurry were tested: a batch of 50 wt% spherical glass beads and a batch of 50 wt% glass frit in process water. No chemicals such as formic acid was used in slurry, only water and glass formers. The glass beads used for this testing were commercially available borosilicate glass of mesh size -100+200. The glass frit was Frit 418 obtained from DWPF and is nominally -45+200 mesh. The spherical glass beads did not have a negative impact on the frit transfer system. The transferring of the spherical glass beads was much easier than the glass frit. It was difficult to create a plug with glass bead slurry in the pilot transfer system. When a small plug occurred from setting overnight with the spherical glass beads, the plug was easy to displace using only the pump. In the case of creating a man made plug in a vertical line, by filling the line with spherical glass beads and allowing the slurry to settle for days, the plug was easy to remove by using flush water. The glass frit proved to be much more difficult to transfer when compared to the spherical glass beads. The glass frit impacted the transfer system to the point

Shell Vial culture Assay for the rapid diagnosis of Japanese encephalitis, West Nile and Dengue-2 viral encephalitis

Directory of Open Access Journals (Sweden)

Badrinath S

2006-01-01

Full Text Available Abstract Background Encephalitis caused by flaviviruses, Japanese encephalitis virus (JEV and West Nile virus (WNV is responsible for significant morbidity and mortality in many endemic countries. Dengue-2 (Den-2 virus is a recent addition to the list of encephalitogenic viruses, after its Central Nervous System (CNS invasion capability has been established. There is a wide array of laboratory tools that have helped us not only in the diagnosis of these conditions but also in understanding their pathogenesis and pathology. However, there are no reports of Shell Vial Culture (SVC, a centrifuge enhanced tissue culture assay that has revolutionized viral culturing in terms of rapidity and sensitivity being optimized for these flaviviral encephalitic conditions. The present study is an attempt to standardize and evaluate the usefulness of SVC for the laboratory diagnosis of JE, WN and Den-2 encephalitis cases and to compare it with Indirect Immunofluorescence (IIF technique that detects cell associated virus antigen. Analysis of the various clinical parameters with respect to viral etiology has also been carried out. Results Pediatric patients constituted the major group involved in the study (92%. Etiological diagnosis of viral encephalitis could be established in twenty nine (58% patients. JE encephalitis was the commonest with 19 (39% cases being positive followed by, WN (9 cases-18% and Den-2 (one case. IIF test could detect antigens of JE, WN and Den-2 viruses in 16(32%, 7(14% and 1 case respectively. Shell vial culture assay picked up all cases that were positive by IIF test. In addition, SVC assay could detect 3 and 2 more cases of JE and WN encephalitis respectively, that were negative by the IIF test. Conclusion Shell vial culture is a rapid and efficient tool for the etiological diagnosis of JE, WN and Den-2 encephalitis cases. Early, prompt collection, transport and processing of the CSF samples, would make SVC a better method for the

Effect of different glasses in glass bonded zeolite

International Nuclear Information System (INIS)

Lewis, M.A.; Ackerman, J.P.; Verma, S.

1995-01-01

A mineral waste form has been developed for chloride waste salt generated during the pyrochemical treatment of spent nuclear fuel. The waste form consists of salt-occluded zeolite powders bound within a glass matrix. The zeolite contains the salt and immobilizes the fission products. The zeolite powders are hot pressed to form a mechanically stable, durable glass bonded zeolite. Further development of glass bonded zeolite as a waste form requires an understanding of the interaction between the glass and the zeolite. Properties of the glass that enhance binding and durability of the glass bonded zeolite need to be identified. Three types of glass, boroaluminosilicate, soda-lime silicate, and high silica glasses, have a range of properties and are now being investigated. Each glass was hot pressed by itself and with an equal amount of zeolite. MCC-1 leach tests were run on both. Soda-lime silicate and high silica glasses did not give a durable glass bonded zeolite. Boroaluminosilicate glasses rich in alkaline earths did bind the zeolite and gave a durable glass bonded zeolite. Scanning electron micrographs suggest that the boroaluminosilicate glasses wetted the zeolite powders better than the other glasses. Development of the glass bonded zeolite as a waste form for chloride waste salt is continuing

Effect of the Changes of Respiratory Tract Model on the Uranium Bioassay Data

Energy Technology Data Exchange (ETDEWEB)

Kwon, Taeeun; Noh, Siwan; Kim, Meeryeong; Lee, Jaiki [Hanyang Univ., Seoul (Korea, Republic of); Lee, Jongil; Kim, Jang Lyul [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2014-05-15

The HRTM, however, was revised based on the recent experimental data in OIR (Occupational Intakes of Radionuclides) draft report of ICRP. The changes of respiratory tract model are predicted to directly affect bioassay data like retention and excretion functions. Lung retention function is especially important to internal exposure assessment for workers related to fuel manufacturing because the place could be contaminated by uranium. In addition, faecel samples are recommended to be used for in-vitro bioassay of uranium because of very slow excretion via urine. More reliable assessments for the workers in fuel manufacturing could be achieved by recalculation of bioassay data for uranium and the comparing study using original and revised HRTM. In this study, therefore, the lung retention and faecal excretion functions for inhalation of UO{sub 2} and U{sub 3}O{sub 8} were recalculated using revised HRTM and the results were compared with those of original HRTM. In this study the lung retention and faecal excretion functions for inhalation of UO{sub 2} and U{sub 3}O{sub 8} were calculated based on original and revised HRTM. The results show that the revised HRTM increases lung retention and uptakes to alimentary tract which cause the more faecal excretion. The results in this study confirm the effect of the changes of respiratory tract model on the uranium bioassay data although the more study is needed to apply to practical fields.

Evaluating the efficacy of biological and conventional insecticides with the new 'MCD bottle' bioassay.

Science.gov (United States)

Sternberg, Eleanore D; Waite, Jessica L; Thomas, Matthew B

2014-12-16

Control of mosquitoes requires the ability to evaluate new insecticides and to monitor resistance to existing insecticides. Monitoring tools should be flexible and low cost so that they can be deployed in remote, resource poor areas. Ideally, a bioassay should be able to simulate transient contact between mosquitoes and insecticides, and it should allow for excito-repellency and avoidance behaviour in mosquitoes. Presented here is a new bioassay, which has been designed to meet these criteria. This bioassay was developed as part of the Mosquito Contamination Device (MCD) project and, therefore, is referred to as the MCD bottle bioassay. Presented here are two experiments that serve as a proof-of-concept for the MCD bottle bioassay. The experiments used four insecticide products, ranging from fast-acting, permethrin-treated, long-lasting insecticide nets (LLINs) that are already widely used for malaria vector control, to the slower acting entomopathogenic fungus, Beauveria bassiana, that is currently being evaluated as a prospective biological insecticide. The first experiment used the MCD bottle to test the effect of four different insecticides on Anopheles stephensi with a range of exposure times (1 minute, 3 minutes, 1 hour). The second experiment is a direct comparison of the MCD bottle and World Health Organization (WHO) cone bioassay that tests a subset of the insecticides (a piece of LLIN and a piece of netting coated with B. bassiana spores) and a further reduced exposure time (5 seconds) against both An. stephensi and Anopheles gambiae. Immediate knockdown and mortality after 24 hours were assessed using logistic regression and daily survival was assessed using Cox proportional hazards models. Across both experiments, fungus performed much more consistently than the chemical insecticides but measuring the effect of fungus required monitoring of mosquito mortality over several days to a week. Qualitatively, the MCD bottle and WHO cone performed comparably

Single-core magnetic markers in rotating magnetic field based homogeneous bioassays and the law of mass action

Energy Technology Data Exchange (ETDEWEB)

Dieckhoff, Jan, E-mail: j.dieckhoff@tu-bs.de [Institut fuer Elektrische Messtechnik und Grundlagen der Elektrotechnik, TU Braunschweig, Braunschweig (Germany); Schrittwieser, Stefan; Schotter, Joerg [Molecular Diagnostics, AIT Austrian Institute of Technology, Vienna (Austria); Remmer, Hilke; Schilling, Meinhard; Ludwig, Frank [Institut fuer Elektrische Messtechnik und Grundlagen der Elektrotechnik, TU Braunschweig, Braunschweig (Germany)

2015-04-15

In this work, we report on the effect of the magnetic nanoparticle (MNP) concentration on the quantitative detection of proteins in solution with a rotating magnetic field (RMF) based homogeneous bioassay. Here, the phase lag between 30 nm iron oxide single-core particles and the RMF is analyzed with a fluxgate-based measurement system. As a test analyte anti-human IgG is applied which binds to the protein G functionalized MNP shell and causes a change of the phase lag. The measured phase lag changes for a fixed MNP and a varying analyte concentration are modeled with logistic functions. A change of the MNP concentration results in a nonlinear shift of the logistic function with the analyte concentration. This effect results from the law of mass action. Furthermore, the bioassay results are used to determine the association constant of the binding reaction. - Highlights: • A rotating magnetic field based homogeneous bioassay concept was presented. • Here, single-core iron oxide nanoparticles are applied as markers. • The impact of the particle concentration on the bioassay results is investigated. • The relation between particle concentration and bioassay sensitivity is nonlinear. • This finding can be reasonably explained by the law of mass action.

Banco de ensayos para materiales piezoeléctricos en aplicaciones viales

Directory of Open Access Journals (Sweden)

de Frutos, J.

2011-04-01

Full Text Available The test bench system described in this paper performs experiments on piezoelectric materials used in road traffic applications, covering a range between 14 and 170 km/h, which is considered enough for testing under standard traffic conditions. A software has been developed to control the three phase induction motor driver and to acquire all the measurement data of the piezoelectric materials. The mass over each system’s axis can be selected, with a limit of 60 kg over each wheel. The test bench is used to simulate the real behaviour of buried piezoelectric cables in road traffic applications for both light and heavy vehicles. This new test bed system is a powerful research tool and can be applied to determine the optimal installation and configuration of the piezoelectric cable sensors and opens a new field of research: the study of energy harvesting techniques based on piezoelectric materials.

En este trabajo se define y propone un banco de ensayos que permite testar materiales piezoeléctricos para aplicaciones viales en sus diferentes configuraciones en un rango de velocidad entre los 14 y los 170 km/h, lo que cubre sobradamente las condiciones de tráfico real. Tanto el control del variador de velocidad del motor trifásico que realiza el accionamiento del banco, como la recogida de resultados de medida en las pruebas de excitación y de fatiga de los compuestos piezoeléctricos, se realiza de forma automatizada mediante código informatico. El peso que soporta cada eje del banco es configurable, permitiendo reproducir las señales obtenidas en aplicaciones donde los materiales piezoeléctricos actúan de sensores enterrados en la calzada para vehículos tanto pesados como ligeros. Gracias a esta nueva herramienta se facilita la investigación con materiales de este tipo en aplicaciones viales optimizando tanto el tipo como la disposición e instalación de los mismos, además de abrir el camino a la novedosa investigación sobre

Functional diagnostics for thyrotropin hormone receptor autoantibodies: bioassays prevail over binding assays.

Science.gov (United States)

Lytton, Simon David; Schluter, Anke; Banga, Paul J

2018-06-01

Autoantibodies to the thyrotropin hormone receptor (TSH-R) are directly responsible for the hyperthyroidism in Graves' disease and mediate orbital manifestations in Graves' orbitopathy (otherwise known as thyroid eye disease). These autoantibodies are heterogeneous in their function and collectively referred to as TRAbs. Measurement of TRAbs is clinically important for diagnosis of a variety of conditions and different commercial assays with high sensitivity and specificity are available for diagnostic purposes. This review provides overwhelming evidence that the TRAbs detected in binding assays by mainly the automated electrochemical luminescence immunoassays (ECLIA) do not distinguish TRAbs that stimulate the TSH-R (called TSIs or TSAbs) and TRAbs that just inhibit the binding of TSH without stimulating the TSH-R (called TBAbs). However, TSAbs and TBAbs have divergent pathogenic roles, and depending which fraction predominates cause different clinical symptoms and engender different therapeutic regimen. Therefore, diagnostic distinction of TSAbs and TBAbs is of paramount clinical importance. To date, only bioassays such as the Mc4 TSH-R bioassay (Thyretain TM , Quidel) and the Bridge assay (Immulite 2000, Siemens) can measure TSAbs, with only the former being able to distinguish between TSAbs and TBAbs. On this note, it is strongly recommended to only use the term TSI or TSAb when reporting the results of bioassays, whereas the results of automated TRAb binding assays should be reported as TRAbs (of undetermined functional significance). This review aims to present a technical and analytical account of leading commercial diagnostic methods of anti-TSH-R antibodies, a metaanalysis of their clinical performance and a perspective for the use of cell based TSH-R bioassays in the clinical diagnostics of Graves' disease.

Seasonally and regionally determined indication potential of bioassays in contaminated river sediments.

Science.gov (United States)

Hilscherová, Klára; Dusek, Ladislav; Sídlová, Tereza; Jálová, Veronika; Cupr, Pavel; Giesy, John P; Nehyba, Slavomír; Jarkovský, Jirí; Klánová, Jana; Holoubek, Ivan

2010-03-01

River sediments are a dynamic system, especially in areas where floods occur frequently. In the present study, an integrative approach is used to investigate the seasonal and spatial dynamics of contamination of sediments from a regularly flooded industrial area in the Czech Republic, which presents a suitable model ecosystem for pollutant distribution research at a regional level. Surface sediments were sampled repeatedly to represent two different hydrological situations: spring (after the peak of high flow) and autumn (after longer period of low flow). Samples were characterized for abiotic parameters and concentrations of priority organic pollutants. Toxicity was assessed by Microtox test; genotoxicity by SOS-chromotest and green fluorescent protein (GFP)-yeast test; and the presence of compounds with specific mode of action by in vitro bioassays for dioxin-like activity, anti-/androgenicity, and anti-/estrogenicity. Distribution of organic contaminants varied among regions and seasonally. Although the results of Microtox and genotoxicity tests were relatively inconclusive, all other specific bioassays led to statistically significant regional and seasonal differences in profiles and allowed clear separation of upstream and downstream regions. The outcomes of these bioassays indicated an association with concentrations of polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs) as master variables. There were significant interrelations among dioxin-like activity, antiandrogenicity and content of organic carbon, clay, and concentration of PAHs and PCBs, which documents the significance of abiotic factors in accumulation of pollutants. The study demonstrates the strength of the specific bioassays in indicating the changes in contamination and emphasizes the crucial role of a well-designed sampling plan, in which both spatial and temporal dynamics should be taken into account, for the correct interpretations of information in risk assessments.

Comparison of liquid chromatographic and bioassay procedures for determining depletion of intramuscularly injected tylosin.

Science.gov (United States)

Moats, W A; Harris, E W; Steele, N C

1985-01-01

Crossbred pigs weighing 80-110 kg were injected intramuscularly in the ham with 8.8 mg/kg tylosin. Animals were slaughtered in groups of 3 at intervals of 4 h, and 1, 2, 4, and 8 days after injection, and samples of blood, injected muscle, uninjected muscle, liver, and kidney were analyzed by liquid chromatography (LC) and by bioassay using Sarcina lutea as the test organism. The LC method was far more sensitive with a detection limit of less than 0.1 ppm, while the detection limit by bioassay was about 0.5 ppm in tissue. Results by bioassay and LC sometimes differed considerably for tissue samples. Residues in all tissues were below the tolerance limit of 0.2 ppm at 24 h, except in the injected muscle in one animal. Residues were not detected in any tissue of any animal at 48 h after treatment.

Fluorescent bioassays for toxic metals in milk and yoghurt

Science.gov (United States)

2012-01-01

Background From a human health viewpoint, contaminated milk and its products could be a source of long-term exposure to toxic metals. Simple, inexpensive, and on-site assays would enable constant monitoring of their contents. Bioassays that can measure toxic metals in milk or yoghurt might reduce the risk. For this purpose, the green fluorescent protein (GFP)-tagged trans factors, ArsR-GFP and CadC-GFP, together with their cis elements were used to develop such bioassays. Results ArsR-GFP or CadC-GFP, which binds either toxic metal or DNA fragment including cis element, was directly mixed with cow’s milk or yoghurt within a neutral pH range. The fluorescence of GFP, which is reflected by the association/dissociation ratio between cis element and trans factor, significantly changed with increasing externally added As (III) or Cd (II) whereas smaller responses to externally added Pb (II) and Zn (II) were found. Preparation and dilution of whey fraction at low pH were essential to intrinsic zinc quantification using CadC-GFP. Using the extraction procedure and bioassay, intrinsic Zn (II) concentrations ranging from 1.4 to 4.8 mg/l for milk brands and from 1.2 to 2.9 mg/kg for yoghurt brands were determined, which correlated to those determined using inductively coupled plasma atomic emission spectroscopy. Conclusions GFP-tagged bacterial trans factors and cis elements can work in the neutralized whole composition and diluted whey fraction of milk and yoghurt. The feature of regulatory elements is advantageous for establishment of simple and rapid assays of toxic metals in dairy products. PMID:23098077

Fluorescent bioassays for toxic metals in milk and yoghurt

Directory of Open Access Journals (Sweden)

Siddiki Mohammad Shohel

2012-10-01

Full Text Available Abstract Background From a human health viewpoint, contaminated milk and its products could be a source of long-term exposure to toxic metals. Simple, inexpensive, and on-site assays would enable constant monitoring of their contents. Bioassays that can measure toxic metals in milk or yoghurt might reduce the risk. For this purpose, the green fluorescent protein (GFP-tagged trans factors, ArsR-GFP and CadC-GFP, together with their cis elements were used to develop such bioassays. Results ArsR-GFP or CadC-GFP, which binds either toxic metal or DNA fragment including cis element, was directly mixed with cow’s milk or yoghurt within a neutral pH range. The fluorescence of GFP, which is reflected by the association/dissociation ratio between cis element and trans factor, significantly changed with increasing externally added As (III or Cd (II whereas smaller responses to externally added Pb (II and Zn (II were found. Preparation and dilution of whey fraction at low pH were essential to intrinsic zinc quantification using CadC-GFP. Using the extraction procedure and bioassay, intrinsic Zn (II concentrations ranging from 1.4 to 4.8 mg/l for milk brands and from 1.2 to 2.9 mg/kg for yoghurt brands were determined, which correlated to those determined using inductively coupled plasma atomic emission spectroscopy. Conclusions GFP-tagged bacterial trans factors and cis elements can work in the neutralized whole composition and diluted whey fraction of milk and yoghurt. The feature of regulatory elements is advantageous for establishment of simple and rapid assays of toxic metals in dairy products.

Efficient algal bioassay based on short-term photosynthetic response

International Nuclear Information System (INIS)

Giddings, J.M.; Stewart, A.J.; O'Neill, R.V.; Gardner, R.H.

1983-01-01

A procedure is described for measuring the effects of toxicants on algal photosynthesis (carbon-14 bicarbonate (H 14 CO 3 )uptake) in 4-h experiments. The results for individual aromatic compounds and the water-soluble fraction (WSF) of a synthetic oil are presented as examples of applications of the bioassay. The toxicity of the WSF varied among the seven algal species tested, and the responses of some species were pH-dependent. With Selenastrum capricornutum as the test organism, the bioassay results were unaffected by variations in pH from 7.0 to 9.0, light intensity from 40 to 200 μeinsteins m -2 s -1 , culture density up to 0.5 mg chlorophyll a per litre, and agitation up to 100 rpm. The photosynthesis bioassay is simpler and faster (4 h versus 4 to 14 days), uses smaller culture volumes, and requires less space than static culture-growth tests. One person can conveniently test four materials per day, and the entire procedure, including preparation, exposure, and analysis, takes less than two days. The short incubation time reduces bottle effects such as pH changes, accumulation of metabolic products, nutrient depletion, and bacterial growth. Processes that remove or alter the test materials are also minimized. The data presented here indicate that algal photosynthesis is inhibited at toxicant concentrations similar to those that cause acute effects in aquatic animals. A model of a pelagic ecosystem is used to demonstrate that even temporary (seven-day) inhibition of algal photosynthesis can have a measurable impact on other trophic levels, particularly if the other trophic levels are also experiencing toxic effects. 25 references, 6 figures, 1 table

Assessment of N and P in organic fertilizer using the missing element technique and a microbial bioassay

International Nuclear Information System (INIS)

Salas, E.; Ramirez, C.

2002-01-01

Assessment of N and P in organic fertilizers using the missing element technique and a microbial bioassay.Through a greenhouse bioassay, using sorghum (Sorghum vulgare) as a test plant, and a microbial assay the availability of N and P in 6 substrates was determined, namely: soil alone and in combination with several organic amendments 10% W/W of chicken manure (CM), compost (C), bocashi (B), vermicompost (V) and coffe hulls (Br). In the microbial assay a complete randomized design with 6 replicates was used; the microbial biomass (BM) was determined 2 days after the glucose amendment of each treatment. In both bioassays a 2 X 2 factorial (N and P fertilization) was establish and the following combinations resulted: +N, +P, +P+N and -P-N (control). For the greenhouse experiment, a complete randomized design with 4 replicates was used. Above-ground plant material of sorghum was harvested 34 days after showing to determine plant dry weight (PS) and content of N and P. Both assays showed a response to the soil amendment with N and P. Soil treatments with CM, C and B showed the highest values of PS and BM. Soil treatment with CM amended with N, P or both did not showed a response in PS or BM, in C and B there was a response to N addition but not to P. In treatments with V and Br, the lowest values for PS and BM were obtained, and there was a growth response to N and P. Both bioassays were able to pinpoint N and P defficiencies in the soil as well in some of the mixtures of soil with organic amendments. A high correlation was encountered between the greenhouse assay and the microbial bioassay (r= 0.86, P=0.0001). Therefore, the microbial bioassay can be a cheaper alternative to the plant bioassay not only to evaluate the nutritional quality of compost but also to identify nutrient deficiencies in soils as well as in substrates amended with organic fertilizers. (Author) [es

Implementación de trazados viales, según el uso y ocupación del suelo (COS – CUS), en ciudades del Ecuador con menos 260.000 habitantes

OpenAIRE

Ayabaca Cazar, Fabián Ramiro

2014-01-01

El objetivo de esta investigación es establecer un esquema básico de procedimientos para la implementación de un estudio que permita el desarrollo de una red vial aplicando la reglamentación de uso y ocupación del suelo, en relación con las nuevas leyes vigentes, así como, facilitar al técnico municipal con una guía para establecer los estudios necesarios previos a la aplicación de un diseño de un trazado vial. En la parte inicial de investigación permitió identificar las estructuras legal...

Phototoxicity activity of Psoralea drupacea L. using Atremia salina bioassay system

Directory of Open Access Journals (Sweden)

Mohammad Ramezani

2011-07-01

Conclusion: The result showed that P. drupacea methanolic extract and chloroform fraction have phototoxicity in A. salina bioassay system and their toxic effect is related to phototoxic constituents such as psoralen.

UTILITY OF A FULL LIFE-CYCLE COPEPOD BIOASSAY APPROACH FOR ASSESSMENT OF SEDIMENT-ASSOCIATED CONTAMINANT MIXTURES. (R825279)

Science.gov (United States)

AbstractWe compared a 21 day full life-cycle bioassay with an existing 14 day partial life-cycle bioassay for two species of meiobenthic copepods, Microarthridion littorale and Amphiascus tenuiremis. We hypothesized that full life-cycle tests would bette...

Bioassay method for toxicity studies of insecticide formulations to Tuta absoluta (meyrick, 1917 Metodologia de bioensaio para estudos de toxicidade de formulações comerciais de inseticidas a Tuta absoluta (Meyrick, 1917

Directory of Open Access Journals (Sweden)

Tarcísio Visintin da Silva Galdino

2011-10-01

Full Text Available Chemical control is the main method for controlling the tomato leafminer, Tuta absoluta (Meyrick, 1917 (Lepidoptera: Gelechiidae. Reported techniques for the evaluation of insecticide toxicity to the tomato leafminer are not in agreement with field conditions and do not allow us to verify whether doses used in the field are efficient for control. Thus, the objective of this work was to develop a bioassay methodology to study the toxicity of insecticide formulations to T. absoluta that represent field conditions for fast-acting insecticides (neurotoxics and inhibitors of respiration and slow-acting insecticides (Bacillus thuringiensis and insect growth regulators. The leaf-dip method was the most efficient method for toxicity studies of insecticides formulations to T. absoluta. We verified that bioassays with fast-acting insecticides should be performed with glass Petri dishes containing one tomato foliole from the 4th leaf from the plant apex infested with 10 larvae of 3rd instar and these bioassays can last 48 hours. Conversely, bioassays with slow-acting insecticides should be performed with two-liter transparent PET bottles containing the 4th leaf from the plant apex, with their petioles immersed in a glass bottle containing 120 mL of water, and this leaf should be infested with 10 larvae of 2nd instar and this bioassays can last seven days.O principal método utilizado no controle da traça-do-tomateiro Tuta absoluta (Meyrick, 1917 (Lepidoptera: Gelechiidae é a aplicação de inseticidas. As técnicas atuais de avaliação da toxicidade de inseticidas sobre essa praga não simulam a situação de campo e não possibilitam a verificação se as doses usadas no campo são eficientes no seu controle. Assim, neste trabalho, objetivou-se desenvolver uma metodologia que represente as condições de campo para inseticidas de ação rápida (neurotóxicos e inibidores respiratórios e de ação lenta (Bacillus thuringiensis e reguladores de

Formation of biofilm by strains of Listeria monocytogenes isolated ...

African Journals Online (AJOL)

Quantification of biofilm formation by 40 Listeria monocytogenes strains from wara soft cheese and its processing environment was assessed on glass vials surfaces. Attachement to glass surface was quantified using a crystal violet binding assay. All the 40 strains produced biofilms after 48 and 72 h incubation at 37oC.

Building bio-assays with magnetic particles on a digital microfluidic platform.

Science.gov (United States)

Kokalj, Tadej; Pérez-Ruiz, Elena; Lammertyn, Jeroen

2015-09-25

Digital microfluidics (DMF) has emerged as a promising liquid handling technology for a variety of applications, demonstrating great potential both in terms of miniaturization and automation. DMF is based on the manipulation of discrete, independently controllable liquid droplets, which makes it highly reconfigurable and reprogrammable. One of its most exclusive advantages, compared to microchannel-based microfluidics, is its ability to precisely handle solid nano- and microsized objects, such as magnetic particles. Magnetic particles have become very popular in the last decade, since their high surface-to-volume ratio and the possibility to magnetically separate them from the matrix make them perfect suitable as a solid support for bio-assay development. The potential of magnetic particles in DMF-based bio-assays has been demonstrated for various applications. In this review we discuss the latest developments of magnetic particle-based DMF bio-assays with the aim to present, identify and analyze the trends in the field. We also discuss the state-of-the art of device integration, current status of commercialization and issues that still need to be addressed. With this paper we intend to stimulate researchers to exploit and unveil the potential of these exciting tools, which will shape the future of modern biochemistry, microbiology and biomedical diagnostics. Copyright © 2015 Elsevier B.V. All rights reserved.

Investigation of animal and algal bioassays for reliable saxitoxin ecotoxicity and cytotoxicity risk evaluation.

Science.gov (United States)

Perreault, François; Matias, Marcelo Seleme; Melegari, Silvia Pedroso; Pinto, Catia Regina Silva de Carvalho; Creppy, Edmond Ekué; Popovic, Radovan; Matias, William Gerson

2011-05-01

Contamination of water bodies by saxitoxin can result in various toxic effects in aquatic organisms. Saxitoxin contamination has also been shown to be a threat to human health in several reported cases, even resulting in death. In this study, we evaluated the sensitivity of animal (Neuro-2A) and algal (Chlamydomonas reinhardtii) bioassays to saxitoxin effect. Neuro-2A cells were found to be sensitive to saxitoxin, as shown by a 24 h EC50 value of 1.5 nM, which was obtained using a cell viability assay. Conversely, no saxitoxin effect was found in any of the algal biomarkers evaluated, for the concentration range tested (2-128 nM). These results indicate that saxitoxin may induce toxic effects in animal and human populations at concentrations where phytoplankton communities are not affected. Therefore, when evaluating STX risk of toxicity, algal bioassays do not appear to be reliable indicators and should always be conducted in combination with animal bioassays. Copyright © 2011 Elsevier Inc. All rights reserved.

Experimental and Computational Characterization of Biological Liquid Crystals: A Review of Single-Molecule Bioassays

Directory of Open Access Journals (Sweden)

Sungsoo Na

2009-09-01

Full Text Available Quantitative understanding of the mechanical behavior of biological liquid crystals such as proteins is essential for gaining insight into their biological functions, since some proteins perform notable mechanical functions. Recently, single-molecule experiments have allowed not only the quantitative characterization of the mechanical behavior of proteins such as protein unfolding mechanics, but also the exploration of the free energy landscape for protein folding. In this work, we have reviewed the current state-of-art in single-molecule bioassays that enable quantitative studies on protein unfolding mechanics and/or various molecular interactions. Specifically, single-molecule pulling experiments based on atomic force microscopy (AFM have been overviewed. In addition, the computational simulations on single-molecule pulling experiments have been reviewed. We have also reviewed the AFM cantilever-based bioassay that provides insight into various molecular interactions. Our review highlights the AFM-based single-molecule bioassay for quantitative characterization of biological liquid crystals such as proteins.

Evaluation of soil bioassays for use at Washington state hazardous waste sites: A pilot study

International Nuclear Information System (INIS)

Blakley, N.; Norton, D.; Stinson, M.; Boyer, R.

1994-01-01

The Washington State Department of Ecology (Ecology) is developing guidelines to assess soil toxicity at hazardous waste sites being investigated under the Washington Model Toxics Control Act Cleanup Regulation. To evaluate soil toxicity, Ecology selected five bioassay protocols -- Daphnia, Earthworm, Seedling, Fathead Minnow, and Frog Embryo Teratogenesis Assay Xenopus (FETAX) -- for use as screening level assessment tools at six State hazardous waste sites. Sites contained a variety of contaminants including metals, creosote, pesticides, and petroleum products (leaking underground storage tanks). Three locations, representing high, medium, and low levels of contamination, were samples at each site. In general, the high contaminant samples resulted in the highest toxic response in all bioassays. The order of site toxicity, as assessed by overall toxic response, is creosote, petroleum products, metals, and pesticides. Results indicate that human health standards, especially for metals, may not adequately protect some of the species tested. The FETAX bioassay had the greatest overall number of toxic responses and lowest variance. The seedling and Daphnia bioassays had lower and similar overall toxic response results, followed by the earthworm and fathead minnow. Variability was markedly highest for the seedling. The Daphnia and fathead minnow variability were similar to the FETAX level, while the earthworm variability was slightly higher

Bioassay-guided studies on the cytotoxic and in vitro trypanocidal ...

African Journals Online (AJOL)

This paper reports a bioassay-guided study to search for possible biological activity (cytotoxic and trypanocidal) in two Ugandan medicinal plants. The methodology adopted was the so-called ping-pong approach, involving phytochemical purification (column chromatography and preparative thin layer chromatography), ...

Intemational collaborative study on the preparation of 1st international standard for rhTSH for bioassay

International Nuclear Information System (INIS)

Huang Ying; Shen Hongzheng; Yu Ting; Xu Ligen

2007-01-01

The history of the international collaborative studies on the preparation of standards of TSH for bioassay and immunoassay was reviewed. The result of collaborative study on the 1st international standard for thyroid-stimulating hormone, recombinant, human, for bioassay was reported in detail in this article. Based on the results of this collaborative study, it is proposed that the candidate standard be established as the international standard for rhTSH for bioassay, and be assigned an activity of 9.5 IU per ampoule. The national standard preparation of TSH for immunoassay was also reassayed, revealing the potency to be 0.557 mIU/ampoule, i.e. 92. 8% of the labelled value of 0.600mIU/ampoule, a reasonable consistency. (authors)

Bioassays with terrestrial and aquatic species as monitoring tools of hydrocarbon degradation.

Science.gov (United States)

Bori, Jaume; Vallès, Bettina; Ortega, Lina; Riva, Maria Carme

2016-09-01

In this study chemical analyses and ecotoxicity tests were applied for the assessment of a heavily hydrocarbon-contaminated soil prior and after the application of a remediation procedure that consisted in the stimulation of soil autochthonous populations of hydrocarbon degraders in static-ventilated biopiles. Terrestrial bioassays were applied in mixtures of test soils and artificial control soil and studied the survival and reproduction of Eisenia fetida and the avoidance response of E. fetida and Folsomia candida. Effects on aquatic organisms were studied by means of acute tests with Vibrio fischeri, Raphidocelis subcapitata, and Daphnia magna performed on aqueous elutriates from test soils. The bioremediation procedure led to a significant reduction in the concentration of hydrocarbons (from 34264 to 3074 mg kg(-1), i.e., 91 % decrease) and toxicity although bioassays were not able to report a percentage decrease of toxicity as high as the percentage reduction. Sublethal tests proved the most sensitive terrestrial bioassays and avoidance tests with earthworms and springtails showed potential as monitoring tools of hydrocarbon remediation due to their high sensitivity and short duration. The concentrations of hydrocarbons in water extracts from test soils were 130 and 100 μg L(-1) before and after remediation, respectively. Similarly to terrestrial tests, most aquatic bioassays detected a significant reduction in toxicity, which was almost negligible at the end of the treatment. D. magna survival was the most affected by soil elutriates although toxicity to the crustacean was associated to the salinity of the samples rather than to the concentration of hydrocarbons. Ecotoxicity tests with aqueous soil elutriates proved less relevant in the assessment of hydrocarbon-contaminated soils due to the low hydrosolubility of hydrocarbons and the influence of the physicochemical parameters of the aquatic medium.

Characterization of glass and glass ceramic nuclear waste forms

International Nuclear Information System (INIS)

Lutze, W.; Borchardt, J.; De, A.K.

1979-01-01

Characteristics of solidified nuclear waste forms, glass and glass ceramic compositions and the properties (composition, thermal stability, crystallization, phase behavior, chemical stability, mechanical stability, and radiation effects) of glasses and glass ceramics are discussed. The preparation of glass ceramics may be an optional step for proposed vitrification plants if tailored glasses are used. Glass ceramics exhibit some improved properties with respect to glasses. The overall leach resistance is similar to that of glasses. An increased leach resistance may become effective for single radionuclides being hosted in highly insoluble crystal phases mainly when higher melting temperatures are applicable in order to get more leach resistant residual glass phases. The development of glass ceramic is going on. The technological feasibility is still to be demonstrated. The potential gain of stability when using glass ceramics qualifies the material as an alternative nuclear waste form

Optimización de la oferta vial para el transporte privado de la ciudad de Azogues

OpenAIRE

Cabrera Vélez, Sonia Lucía

2017-01-01

La optimización de la oferta vial para el transporte privado en la ciudad de Azogues, se obtiene a través de la implementación de los Sistemas Inteligentes de Transporte, que son un conjunto de soluciones diseñadas para mejorar la operación y seguridad del transporte. Enmarcados en este concepto, dentro de la Ciudad de Azogues, se estudió este tema debido al crecimiento de la flota vehicular, en gran parte, producto del aumento económico de los ingresos familiares por el fenómeno migratorio, ...

Interpretation of bioassay data from nuclear fuel fabrication workers

International Nuclear Information System (INIS)

Melo, D.; Xavier, M.

2005-01-01

Full text: In nuclear fuel fabrication facilities, workers are exposed to different compounds of enriched uranium. Although in this kind of facility the main route of intake is inhalation, ingestion may occur in some situations. The interpretation of the bioassay data is very complex, since it is necessary taking into account all the different parameters, which is a big challenge. Due to the high cost of the individual monitoring programme for internal dose assessment in the routine monitoring programmes, usually only one type of measurement is assigned. In complex situations like the one described in this paper, where several parameters can compromise the accuracy of the bioassay interpretation it is need to have a combination of techniques to evaluate the internal dose. According to ICRP 78 (1997), the general order of preference in terms of accuracy of interpretation is: body activity measurement, excreta analysis and personal air sampling. Results of monitoring of working environment may provide information that assists in interpretation on particle size, chemical form and solubility, time of intake. A group of seventeen workers from controlled area of the fuel fabrication facility was selected to evaluate the internal dose using all different available techniques during a certain period. The workers were monitored for determination of uranium content in the daily urinary and faecal excretion (collected over a period of 3 consecutive days), chest counting and personal air sampling. The results have shown that at least two types of sensitivity techniques must be used, since there are some sources of uncertainties on the bioassay interpretation, like mixture of uranium compounds intake and different routes of intake. The combination of urine and faeces analysis has shown to be the more appropriate methodology for assessing internal dose in this situation. (author)

Evaluación del pavimento de la carretera “cumbe – oña (tramo i)” de 20 km de longitud, ubicada en la provincia del Azuay mediante equipos de auscultación vial

OpenAIRE

Bravo Castro, María Fernanda

2011-01-01

Evaluacion del Pavimento de la Carretera “Cumbe – Oña (Tramo I)” de 20 Km de longitud, ubicada en la Provincia del Azuay mediante Equipos de Auscultación Vial Evaluacion del Pavimento de la Carretera “Cumbe – Oña (Tramo I)” de 20 Km de longitud, ubicada en la Provincia del Azuay mediante Equipos de Auscultación Vial

Optimization and field use of a bioassay to monitor sea lice Lepeophtheirus salmonis sensitivity to emamectin benzoate.

Science.gov (United States)

Westcott, Jillian D; Stryhn, Henrik; Burka, John F; Hammell, K Larry

2008-04-01

A bioassay for sea lice Lepeophtheirus salmonis sensitivity towards emamectin benzoate (EMB) was validated for field use. A probit regression model with natural responsiveness was used for the number of affected (moribund or dead) sea lice in bioassays involving different concentrations of EMB. Bioassay optimization included an evaluation of the inter-rater reliability of sea lice responsiveness to EMB and an evaluation of gender-related differences in susceptibility. Adoption of a set of bioassay response criteria improved the concordance (evaluated using the concordance correlation coefficient) between raters' assessments and the model estimation of EC50 values (the 'effective concentration' leading to a response of 50% of the lice not prone to natural response). An evaluation of gender-related differences in EMB susceptibility indicated that preadult stage female sea lice exhibited a significantly larger sensitivity towards EMB in 12 of 19 bioassays compared to preadult males. In order to evaluate sea lice sensitivity to EMB in eastern Canada, the intensive salmon farming area in the Bay of Fundy in southwestern New Brunswick was divided into 4 distinct regions based on industry health management practices and hydrographics. A total of 38 bioassays were completed from 2002 to 2005 using populations of preadult stage sea lice collected from Atlantic salmon Salmo salar farms within the 4 described regions. There was no significant overall effect of region or year on EC50 values; however, analysis of variance indicated a significant effect of time of year on EC50 values in 2002 and a potential effect in 2004 to 2005. Although the range of EC50 values obtained in this 3 yr study did not appear sufficient to affect current clinical success in the control of sea lice, the results suggest a seasonal- or temperature-associated variation in sensitivity to EMB. This will need to be considered if changes in EMB efficacy occur in the future.

Noninvasive quantitation of human liver steatosis using magnetic resonance and bioassay methods

Energy Technology Data Exchange (ETDEWEB)

D' Assignies, Gaspard; Ruel, Martin; Khiat, Abdesslem; Lepanto, Luigi; Kauffmann, Claude; Tang, An [Centre Hospitalier de l' Universite de Montreal (CHUM), Departement de Radiologie, Montreal, Quebec (Canada); Chagnon, Miguel [Universite de Montreal (UDEM), Departement de Mathematiques et de Statistique, Montreal, Quebec (Canada); Gaboury, Louis [Centre Hospitalier de l' Universite de Montreal (CHUM), Departement d' Anatomo-Pathologie, Montreal, Quebec (Canada); Boulanger, Yvan [Centre Hospitalier de l' Universite de Montreal (CHUM), Departement de Radiologie, Montreal, Quebec (Canada); Hopital Saint-Luc du CHUM, Departement de Radiologie, Montreal, Quebec (Canada)

2009-08-15

The purpose was to evaluate the ability of three magnetic resonance (MR) techniques to detect liver steatosis and to determine which noninvasive technique (MR, bioassays) or combination of techniques is optimal for the quantification of hepatic fat using histopathology as a reference. Twenty patients with histopathologically proven steatosis and 24 control subjects underwent single-voxel proton MR spectroscopy (MRS; 3 voxels), dual-echo in phase/out of phase MR imaging (DEI) and diffusion-weighted MR imaging (DWI) examinations of the liver. Blood or urine bioassays were also performed for steatosis patients. Both MRS and DEI data allowed to detect steatosis with a high sensitivity (0.95 for MRS; 1 for DEI) and specificity (1 for MRS; 0.875 for DEI) but not DWI. Strong correlations were found between fat fraction (FF) measured by MRS, DEI and histopathology segmentation as well as with low density lipoprotein (LDL) and cholesterol concentrations. A Bland-Altman analysis showed a good agreement between the FF measured by MRS and DEI. Partial correlation analyses failed to improve the correlation with segmentation FF when MRS or DEI data were combined with bioassay results. Therefore, FF from MRS or DEI appear to be the best parameters to both detect steatosis and accurately quantify fat liver noninvasively. (orig.)

Evaluation of the toxic effects of arsenite, chromate, cadmium, and copper using a battery of four bioassays

Energy Technology Data Exchange (ETDEWEB)

Ko, Kyung-Seok; Lee, Pyeong-Koo [Korea Institute of Geoscience and Mineral Resources (KIGAM), Daejeon (Korea, Republic of). Geologic Environment Div.; Kong, In Chul [Yeungnam Univ., Kyungbuk (Korea, Republic of). Dept. of Environmental Engineering

2012-09-15

The sensitivities of four different kinds of bioassays to the toxicities of arsenite, chromate, cadmium, and copper were compared. The different bioassays exhibited different sensitivities, i.e., they responded to different levels of toxicity of each of the different metals. However, with the exception of the {alpha}-glucosidase enzyme activity, arsenite was the most toxic compound towards all the tested organisms, exhibiting the highest toxic effect on the seeds of Lactuca, with an EC{sub 50} value of 0.63 mg/L. The sensitivities of Lactuca and Raphanus were greater than the sensitivities of two other kinds of seeds tested. Therefore, these were the seeds appropriate for use in a seed germination assay. A high revertant mutagenic ratio (5:1) of Salmonella typhimurium was observed with an arsenite concentration of 0.1 {mu}g/plate, indicative of a high possibility of mutagenicity. These different results suggested that a battery of bioassays, rather than one bioassay alone, is needed as a more accurate and better tool for the bioassessment of environmental pollutants. (orig.)

Accuracy of Cerenkov measurements using a liquid scintillation spectrometer

International Nuclear Information System (INIS)

Takiue, Makoto; Natake, Takashi

1996-01-01

Cerenkov counting efficiency varies with colour quenching and sample turbidity. The activity in a plastic vial can be determined accurately with a colour quenching correction technique, regardless of the presence or absence or turbidity in a sample. On the other hand, the error of the measured activity in a glass vial becomes large with increasing sample turbidity due to the dissimilarity of the quench correction curves for non-turbid and turbid samples. (Author)

Liquid scintillation systems and apparatus for measuring high-energy radiation emitted by samples in standard laboratory test tubes

International Nuclear Information System (INIS)

Benvenutti, R.A.

1976-01-01

Liquid scintillation detection system employs improved sample holders in which the cap of a glass vial is provided with a well for receiving a standard laboratory test tube containing a radioactive sample. The well is immersed in a liquid scintillator in the vial, the scintillator containing lead acetate solution to enhance its efficiency. A commercially available beta-counting liquid scintillation apparatus is modified to provide gamma-counting with the improved sample holders

Heavy water leak detection using diffusion sampler

International Nuclear Information System (INIS)

Joshi, M.L.; Hussain, S.A.

1990-01-01

In the Pressurrised Heavy Water Reactors (PHWRs) detection of the sources of heavy water leaks is importent both for the purpose of radiation hazard control as well as for the reduction of escape/loss of heavy water which, is an expensive nuclear material. This paper describes an application of tritium diffusion sampler for heavy water leak detection. The diffusion sampler comprises an usual tritium counting glass vial with a special orifice. The counting vial has water vapour, deficient in HTO concentration. The HTO present outside diffuses in the vial through the orifice, gets exchanged with water of the wet filter paper kept at the bottom and the moisture in the vial atmosphere which has HTO concentration lower than that outside. This results in continuation of net movement of HTO in the vial. The exchanged tritium is counted in liquid scintillation spectrometer. The method has a sensitivity of 10000 dpm/DAC-h. (author). 2 figs., 2 ta bs

Sampling method, storage and pretreatment of sediment affect AVS concentrations with consequences for bioassay responses.

Science.gov (United States)

De Lange, H J; Van Griethuysen, C; Koelmans, A A

2008-01-01

Sediment treatment and sediment storage may alter sediment toxicity, and consequently biotic response. Purpose of our study was to combine these three aspects (treatment-toxicity-biotic response) in one integrated approach. We used Acid Volatile Sulfide (AVS) concentrations as a proxy of the disturbance of the sediment. AVS and Simultaneously Extracted Metal (SEM) concentrations were compared to bioassay responses with the freshwater benthic macroinvertebrate Asellus aquaticus. Storage conditions and sediment treatment affected AVS but not SEM levels. AVS can be used as a proxy for sediment disturbance. The best way to pretreat the sediment for use in a bioassay in order to maintain initial AVS conditions was to sample the sediment with an Ekman grab, immediately store it in a jar without headspace, and freeze it as soon as possible. In a survey using seven different sediments, bioassay responses of A. aquaticus were correlated with SEM and AVS characteristics.

Investigation of independence in inter-animal tumor-type occurrences within the NTP rodent-bioassay database

Energy Technology Data Exchange (ETDEWEB)

Bogen, K.T. [Lawrence Livermore National Lab., CA (United States); Seilkop, S. [Analytical Sciences, Inc., Durham, NC (United States)

1993-05-01

Statistically significant elevation in tumor incidence at multiple histologically distinct sites is occasionally observed among rodent bioassays of chemically induced carcinogenesis. If such data are to be relied on (as they have, e.g., by the US EPA) for quantitative cancer potency assessment, their proper analysis requires a knowledge of the extent to which multiple tumor-type occurrences are independent or uncorrelated within individual bioassay animals. Although difficult to assess in a statistically rigorous fashion, a few significant associations among tumor-type occurrences in rodent bioassays have been reported. However, no comprehensive studies of animal-specific tumor-type occurrences at death or sacrifice have been conducted using the extensive set of available NTP rodent-bioassay data, on which most cancer-potency assessment for environmental chemicals is currently based. This report presents the results of such an analysis conducted on behalf of the National Research Council`s Committee on Risk Assessment for Hazardous Air Pollutants. Tumor-type associations among individual animals were examined for {approximately}2500 to 3000 control and {approximately}200 to 600 treated animals using pathology data from 62 B6C3F1 mouse studies and 61 F/344N rat studies obtained from a readily available subset of the NTP carcinogenesis bioassay database. No evidence was found for any large correlation in either the onset probability or the prevalence-at-death or sacrifice of any tumor-type pair investigated in control and treated rats and niece, although a few of the small correlations present were statistically significant. Tumor-type occurrences were in most cases nearly independent, and departures from independence, where they did occur, were small. This finding is qualified in that tumor-type onset correlations were measured only indirectly, given the limited nature of the data analyzed.

BIOASSAY STUDIES OF METAL(II) COMPLEXES OF 2,2'-(ETHANE ...

African Journals Online (AJOL)

Preferred Customer

diyldiimino)diacetic acid (EDDA) were prepared and characterized. Coordination complexes of the EDDA ... corresponding amines with alkyl halide to bear diammines of the same class with different substituents. ... Bioassay studies of metal(II) complexes of 2,2'-(ethane-1,2-diyldiimino)diacetic acid. Bull. Chem. Soc. Ethiop.

Screening of hormone-like activities in bottled waters available in Southern Spain using receptor-specific bioassays.

Science.gov (United States)

Real, Macarena; Molina-Molina, José-Manuel; Jiménez-Díaz, Inmaculada; Arrebola, Juan Pedro; Sáenz, José-María; Fernández, Mariana F; Olea, Nicolás

2015-01-01

Bottled water consumption is a putative source of human exposure to endocrine-disrupting chemicals (EDCs). Research has been conducted on the presence of chemicals with estrogen-like activity in bottled waters and on their estrogenicity, but few data are available on the presence of hormonal activities associated with other nuclear receptors (NRs). The aim of this study was to determine the presence of endocrine activities dependent on the activation of human estrogen receptor alpha (hERa) and/or androgen receptor (hAR) in water in glass or plastic bottles sold to consumers in Southern Spain. Hormone-like activities were evaluated in 29 bottled waters using receptor-specific bioassays based on reporter gene expression in PALM cells [(anti-)androgenicity] and cell proliferation assessment in MCF-7 cells [(anti-)estrogenicity] after optimized solid phase extraction (SPE). All of the water samples analyzed showed hormonal activity. This was estrogenic in 79.3% and anti-estrogenic in 37.9% of samples and was androgenic in 27.5% and anti-androgenic in 41.3%, with mean concentrations per liter of 0.113pM 17β-estradiol (E2) equivalent units (E2Eq), 11.01pM anti-estrogen (ICI 182780) equivalent units (ICI 182780Eq), 0.33pM methyltrienolone (R1881) equivalent units (R1881Eq), and 0.18nM procymidone equivalent units (ProcEq). Bottled water consumption contributes to EDC exposure. Hormone-like activities observed in waters from both plastic and glass bottles suggest that plastic packaging is not the sole source of contamination and that the source of the water and bottling process may play a role, among other factors. Further research is warranted on the cumulative effects of long-term exposure to low doses of EDCs. Copyright © 2014 Elsevier Ltd. All rights reserved.

Cryopreserved semen in ecotoxicological bioassays: sensitivity and reliability of cryopreserved Sparus aurata spermatozoa.

Science.gov (United States)

Fabbrocini, Adele; D'Adamo, Raffaele; Del Prete, Francesco; Langellotti, Antonio Luca; Rinna, Francesca; Silvestri, Fausto; Sorrenti, Gerarda; Vitiello, Valentina; Sansone, Giovanni

2012-10-01

The aim of this study was to evaluate the feasibility of using cryopreserved S. aurata semen in spermiotoxicity tests. Cryopreservation is a biotechnology that can provide viable gametes and embryos on demand, rather than only in the spawning season, thus overcoming a limitation that has hindered the use of some species in ecotoxicological bioassays. Firstly, the sperm motility pattern of cryopreserved semen was evaluated after thawing by means of both visual and computer-assisted analyses. Motility parameters in the cryopreserved semen did not change significantly in the first hour after thawing, meaning that they were maintained for long enough to enable their use in spermiotoxicity tests. In the second phase of the research, bioassays were performed, using cadmium as the reference toxicant, in order to evaluate the sensitivity of cryopreserved S. aurata semen to ecotoxicological contamination. The sensitivity of the sperm motility parameters used as endpoints (motility percentages and velocities) proved to be comparable to what has been recorded for the fresh semen of other aquatic species (LOECs from 0.02 to 0.03 mg L(-1)). The test showed good reliability and was found to be rapid and easy to perform, requiring only a small volume of the sample. Moreover, cryopreserved semen is easy to store and transfer and makes it possible to perform bioassays in different sites or at different times with the same batch of semen. The proposed bioassay is therefore a promising starting point for the development of toxicity tests that are increasingly tailored to the needs of ecotoxicology and environmental quality evaluation strategies. Copyright © 2012 Elsevier Inc. All rights reserved.

A review of metal (Pb and Zn) sensitive and pH tolerant bioassay organisms for risk screening of metal-contaminated acidic soils

International Nuclear Information System (INIS)

Chapman, E.Emily V.; Dave, Göran; Murimboh, John D.

2013-01-01

To improve risk estimates at the screening stage of Ecological Risk Assessment (ERA), short duration bioassays tailored to undisturbed soil cores from the contaminated site could be useful. However, existing standardized bioassays use disturbed soil samples and often pH sensitive organisms. This is a problem as naturally acidic soils are widespread. Changing soil properties to suit the test organism may change metal bioavailability, leading to erroneous risk estimates. For bioassays in undisturbed soil cores to be effective, species able to withstand natural soil properties must be identified. This review presents a critical examination of bioassay species' tolerance of acidic soils and sensitivity to metal contaminants such as Pb and Zn. Promising organisms include; Dendrobaena octaedra, Folsomia candida, Caenorhabditis elegans, Oppia nitens, Brassica rapa, Trifolium pratense, Allium cepa, Quercus rubra and Acer rubrum. The MetSTICK test and the Bait lamina test were also identified as suitable microorganism tests. -- Highlights: •Risk screening of metal contaminated soils should consider metal bioavailability. •Metal bioavailability is dependent on soil properties such as pH. •Many standardized bioassay organisms are sensitive to acidic soils. •This review identifies acid tolerant and metal sensitive bioassays and species. •The identified tests can improve risk screening of acidic metal contaminated soil. -- This review identifies bioassay species able to withstand naturally acidic soils while being sensitive to metal contaminants

Streamlined sample cleanup using combined dispersive solid-phase extraction and in-vial filtration for analysis of pesticides and environmental pollutants in shrimp

Science.gov (United States)

A new method of sample preparation was developed and is reported for the first time. The approach combines in-vial filtration with dispersive solid-phase extraction (d-SPE) in a fast and convenient cleanup of QuEChERS (quick, easy, cheap, effective, rugged, and safe) extracts. The method was appli...

Application of single-vial ready-for-use formulation of 111In- or 177Lu-labelled somatostatin analogs.

Science.gov (United States)

de Blois, Erik; Chan, Ho Sze; de Zanger, Rory; Konijnenberg, Mark; Breeman, Wouter A P

2014-02-01

For the sake of safety it would be desirable to store and transport the ready-for-use liquid formulation (diagnostics and therapeutics) of radiolabelled peptides. The use of ethanol, in combination with a mixture of gentisic- and ascorbic acid, has superior effects on stabilizing radiolabelled somatostatin analogs. As a consequence, (111)In- and (177)Lu-labelled somatostatin analogs can be stored and transported in a single-vial ready-for-use liquid formulation up to 7 days after radiolabelling. © 2013 Published by Elsevier Ltd.

Biomagnification of bioassay derived 2,3,7,8-tetrachlorodibenzo-p-dioxin equivalents

Science.gov (United States)

Jones, P.D.; Ankley, G.T.; Best, D. A.; Crawford, R.; DeGalan, N.; Giesy, J.P.; Kubiak, T.J.; Ludwig, J. P.; Newsted, J.L.; Tillitt, D. E.; Verbrugge, D.A.

1993-01-01

In recent years contamination of the Great Lakes ecosystem with planar chlorinated hydrocarbons (PCHs) has attracted considerable concern due to their known reproductive and teratogenic effects. The H4IIE bioassay has been standardized as a means of measuring the biological potency of a PCH mixture as 2,3,7,8-tetrachloro-p-dibenzodioxin equivalents (TCDD-EQ). Using this bioassay we have investigated the biomagnification of TCDD-EQ in a semi-closed ecosystem. The biomagnification of TCDD-EQ is demonstrated and results indicate that the food chain is the major pathway for TCDD-EQ through this ecosystem. The H4IIE assay system is demonstrated to be a viable integrative measure of the total concentration of TCDD-EQ in different trophic levels.

Intercomparison programs - a tool for the implementation of a quality assurance program in bioassay

International Nuclear Information System (INIS)

Mesquita, Sueli A. de; Sousa, Wanderson O.; Juliao, Ligia M.Q.C.; Santos, Maristela S.; Fernandes, Paulo C.P.

2009-01-01

In vitro bioassay laboratories need to have means to demonstrate that they are technically competent, operate an effective quality system, and are able to generate technically valid calibration and test results. The reliability of the results of measurements has a high influence on the reliability of the dose assessment. Inter-laboratory tests are one of the tools for assessing the analytical consistency of in vitro bioassay laboratories. The intercomparison exercises provide an opportunity to compare radiochemistry techniques for in vitro analysis of biological samples. The in vitro Laboratory of the Instituto de Radioprotecao e Dosimetria has therefore participated in the intercomparison exercises sponsored by PROCORAD, ARCAL and IAEA since 1998. The intercomparison exercises comprise measurements of gamma and beta emitters in urine samples and alpha emitters in urine and faecal samples. This paper presents the performance of the IRD in vitro bioassay laboratory in the past intercomparisons. The results demonstrate that in vitro laboratory is able to generate technically valid results, which also guarantee the support for a quality assurance program and accreditation by competent organism in Brazil. (author)

Study and determination of the influence factors of the radiopharmaceutical vials dimensions used for actimeter calibration at IPEN; Estudo e determinacao de fatores de influencia das dimensoes dos frascos de radiofarmacos utilizados no IPEN para calibracao de ativimetros

Energy Technology Data Exchange (ETDEWEB)

Martins, Elaine Wirney

2010-07-01

The efficiency and safety of the nuclear medicine practice depend, among others factors, of a quality control programme, mainly related to the use of the nuclide activity meters (activimeter). One of the most important sources of errors in the activimeter measurements is the thickness, size and volume of the vial that contains the radiopharmaceutical considering that a typical activimeter has its response dependent of the vial used. The objective of this work was to establish a quality control programme and the correction factors for the geometry of the vials used for distribution of radiopharmaceutical and activimeters calibration, considering that the Calibration Laboratory of Instruments (LCI) of the Instituto de Pesquisas Energeticas e Nucleares (IPEN) has a NPL-CRC Secondary Standard Radionuclide Calibrator System, manufactured for the Southern Scientific plc, compound by an ionization chamber well type and a current measurement system, with traceability to National Physical Laboratory (NPL) and calibrated with a P6 vial type with different dimensions of the one used for the IPEN. The radiopharmaceutical produced by IPEN {sup 67}Ga, '1{sup 31}I, {sup 201}Tl and {sup 99}mTc, had been tested using the two different vials. The results shown a maximum variation of 22% for {sup 201}Tl, and the minimum variation was 2.98% for {sup 131}I. The correction factors must be incorporated in the routine calibration of the activimeters. (author)

Use of 236Pu and 242Pu as a radiochemical tracer for estimation of Pu in bioassay samples by fission track analysis

International Nuclear Information System (INIS)

Sawant, Pramilla D.; Prabhu, Supreetha P.; Kalsi, P.C.

2008-01-01

236 Pu and 242 Pu are routinely used as radiochemical yield monitors in India for bioassay monitoring of occupational workers by alpha spectrometry. Fission Track Analysis (FTA) is also being standardized for trace level determination of Pu in bioassay samples. The present study, reports the utility of 236 Pu and 242 Pu as radiochemical tracers in estimation of Pu in bioassay samples by FTA technique. The advantages of using 236 Pu tracer in FTA over 242 Pu as well as the interference caused due to presence of 241 Pu in the bioassay samples of occupational workers handling power reactor grade Pu is discussed. (author)

Intervención estatal, desempeño empresario y ámbitos privilegiados de acumulación: el caso del sector vial durante la última dictadura militar, Argentina (1976-1981)

OpenAIRE

Iramain, Lucas Daniel; Instituto Interdisciplinario de Economía Política de Buenos Aires

2010-01-01

Se abordan los rasgos más significativos de la intervención económica estatal en relación a la construcción de obras públicas viales durante el lapso 1976-1981 y analizar bajo ese mismo período el desempeño económico de las principales empresas intervinientes en el mercado vial. La consecución de estos dos propósitos, a su vez, permitirá establecer si durante esos años se generaron las condiciones propicias para la configuración de un ámbito privilegiado de acumulación (Castellani, 2006), en ...

Electrochromic Glasses.

Science.gov (United States)

1980-07-31

this glass and that dipole-dipole correlations contribute to the "ferroelectric-like" character of this amorphous system. The TeO2 -W03 glasses can only...shows the dielectric constant and Fig. I(b) glass from pure TeO2 ot pure WO. In addition, glass the tan 8 of the WO glass as a function of temperature... glasses containing WO, in various glass forming nitworks of LifO-B1O0, Na:O-BzO,, and TeO2 were prepared from reagent grade oxides at 800 C - 9SO C in

In-vial liquid-liquid microextraction-capillary electrophoresis method for the determination of phenolic acids in vegetable oils.

Science.gov (United States)

Abu Bakar, Nur Bahiyah; Makahleh, Ahmad; Saad, Bahruddin

2012-09-12

An in-vial liquid-liquid microextraction method was developed for the selective extraction of the phenolic acids (caffeic, gallic, cinnamic, ferulic, chlorogenic, syringic, vanillic, benzoic, p-hydroxybenzoic, 2,4-dihydroxybenzoic, o-coumaric, m-coumaric and p-coumaric) in vegetable oil samples. The optimised extraction conditions for 20 g sample were: volume of diluent (n-hexane), 2 mL; extractant, methanol: 5 mM sodium hydroxide (60:40; v/v); volume of extractant, 300 μL (twice); vortex, 1 min; centrifugation, 5 min. Recoveries for the studied phenolic acids were 80.1-119.5%. The simultaneous determination of the phenolic acid extracts was investigated by capillary electrophoresis (CE). Separations were carried out on a bare fused-silica capillary (50 μm i.d.× 40 cm length) involving 25 mM sodium tetraborate (pH 9.15) and 5% methanol as CE background electrolyte in the normal polarity mode, voltage of 30 kV, temperature of 25°C, injection time of 4s (50 mbar) and electropherograms were recorded at 200 nm. The phenolic acids were successfully separated in less than 10 min. The validated in-vial LLME-CE method was applied to the determination of phenolic acids in vegetable oil samples (extra virgin olive oil, virgin olive oil, pure olive oil, walnut oil and grapeseed oil). The developed method shows significant advantages over the current methods as lengthy evaporation step is not required. Copyright © 2012 Elsevier B.V. All rights reserved.

Volume reduction of low-level radioactive waste with a hammermill

International Nuclear Information System (INIS)

Gregory, W.D.

1979-01-01

A Jacobson Model J-3 Hammermill was recently installed at the University of Rochester to process low-level radioactive wastes from hospital and research laboratories. The hammermill will handle both glass and plastic vials of all types. The waste is poured into a hopper located on the top of the seven foot high assembly. The material is gravity fed into the hammermill which is driven by a 15-horsepower motor at 3600 rpm. The waste is pounded by the rotating hammers into a metal screen perforated with one inch holes. The gound-up product is discharged from the bottom of the unit into a 55-gallon shipping drum. A volume reduction of 4:1 has been acheived on an equal mixture of glass and plastic vials

Mass extraction container closure integrity physical testing method development for parenteral container closure systems.

Science.gov (United States)

Yoon, Seung-Yil; Sagi, Hemi; Goldhammer, Craig; Li, Lei

2012-01-01

Container closure integrity (CCI) is a critical factor to ensure that product sterility is maintained over its entire shelf life. Assuring the CCI during container closure (C/C) system qualification, routine manufacturing and stability is important. FDA guidance also encourages industry to develop a CCI physical testing method in lieu of sterility testing in a stability program. A mass extraction system has been developed to check CCI for a variety of container closure systems such as vials, syringes, and cartridges. Various types of defects (e.g., glass micropipette, laser drill, wire) were created and used to demonstrate a detection limit. Leakage, detected as mass flow in this study, changes as a function of defect length and diameter. Therefore, the morphology of defects has been examined in detail with fluid theories. This study demonstrated that a mass extraction system was able to distinguish between intact samples and samples with 2 μm defects reliably when the defect was exposed to air, water, placebo, or drug product (3 mg/mL concentration) solution. Also, it has been verified that the method was robust, and capable of determining the acceptance limit using 3σ for syringes and 6σ for vials. Sterile products must maintain their sterility over their entire shelf life. Container closure systems such as those found in syringes and vials provide a seal between rubber and glass containers. This seal must be ensured to maintain product sterility. A mass extraction system has been developed to check container closure integrity for a variety of container closure systems such as vials, syringes, and cartridges. In order to demonstrate the method's capability, various types of defects (e.g., glass micropipette, laser drill, wire) were created in syringes and vials and were tested. This study demonstrated that a mass extraction system was able to distinguish between intact samples and samples with 2 μm defects reliably when the defect was exposed to air, water

Microplate Bioassay for Determining Substrate Selectivity of "Candida rugosa" Lipase

Science.gov (United States)

Wang, Shi-zhen; Fang, Bai-shan

2012-01-01

Substrate selectivity of "Candida rugosa" lipase was tested using "p"-nitrophenyl esters of increasing chain length (C[subscript 1], C[subscript 7], C[subscript 15]) using the high-throughput screening method. A fast and easy 96-well microplate bioassay was developed to help students learn and practice biotechnological specificity screen. The…

Integrating bioassays and analytical chemistry as an improved approach to support safety assessment of food contact materials.

Science.gov (United States)

Veyrand, Julien; Marin-Kuan, Maricel; Bezencon, Claudine; Frank, Nancy; Guérin, Violaine; Koster, Sander; Latado, Hélia; Mollergues, Julie; Patin, Amaury; Piguet, Dominique; Serrant, Patrick; Varela, Jesus; Schilter, Benoît

2017-10-01

Food contact materials (FCM) contain chemicals which can migrate into food and result in human exposure. Although it is mandatory to ensure that migration does not endanger human health, there is still no consensus on how to pragmatically assess the safety of FCM since traditional approaches would require extensive toxicological and analytical testing which are expensive and time consuming. Recently, the combination of bioassays, analytical chemistry and risk assessment has been promoted as a new paradigm to identify toxicologically relevant molecules and address safety issues. However, there has been debate on the actual value of bioassays in that framework. In the present work, a FCM anticipated to release the endocrine active chemical 4-nonyphenol (4NP) was used as a model. In a migration study, the leaching of 4NP was confirmed by LC-MS/MS and GC-MS. This was correlated with an increase in both estrogenic and anti-androgenic activities as measured with bioassays. A standard risk assessment indicated that according to the food intake scenario applied, the level of 4NP measured was lower, close or slightly above the acceptable daily intake. Altogether these results show that bioassays could reveal the presence of an endocrine active chemical in a real-case FCM migration study. The levels reported were relevant for safety assessment. In addition, this work also highlighted that bioactivity measured in migrate does not necessarily represent a safety issue. In conclusion, together with analytics, bioassays contribute to identify toxicologically relevant molecules leaching from FCM and enable improved safety assessment.

Compatibility of hydroxypropyl-β-cyclodextrin with algal toxicity bioassays

International Nuclear Information System (INIS)

Fai, Patricia Bi; Grant, Alastair; Reid, Brian J.

2009-01-01

Numerous reports have indicated that hydrophobic organic compound bioaccessibility in sediment and soil can be determined by extraction using aqueous hydroxypropyl-β-cyclodextrin (HPCD) solutions. This study establishes the compatibility of HPCD with Selenastrum capricornutum and assesses whether its presence influences the toxicity of reference toxicants. Algal growth inhibition (72 h) showed no significant (P > 0.05) difference at HPCD concentrations up to and including 20 mM. HPCD presence did not influence the toxicity of the inorganic reference toxicant (ZnSO 4 ), with IC50 values of 0.82 μM and 0.85 μM, in the presence and absence of HPCD (20 mM), respectively. However, HPCD presence (20 mM) reduced the toxicity of 2,4-dichlorophenol and the herbicides diuron and isoproturon. These reductions were attributed to inclusion complex formation between the toxicants and the HPCD cavity. Liberation of complexed toxicants, by sample manipulation prior to toxicity assessment, is proposed to provide a sensitive, high throughput, bioassay that reflects compound bioaccessibility. - Compatibility of the biomimetic HPCD extraction method with algal cell growth inhibition bioassays to assess toxicity of reference toxicants and environmental relevant herbicides

Compatibility of hydroxypropyl-{beta}-cyclodextrin with algal toxicity bioassays

Energy Technology Data Exchange (ETDEWEB)

Fai, Patricia Bi; Grant, Alastair [School of Environmental Sciences, University of East Anglia, Norwich NR4 7TJ (United Kingdom); Reid, Brian J. [School of Environmental Sciences, University of East Anglia, Norwich NR4 7TJ (United Kingdom)], E-mail: b.reid@uea.ac.uk

2009-01-15

Numerous reports have indicated that hydrophobic organic compound bioaccessibility in sediment and soil can be determined by extraction using aqueous hydroxypropyl-{beta}-cyclodextrin (HPCD) solutions. This study establishes the compatibility of HPCD with Selenastrum capricornutum and assesses whether its presence influences the toxicity of reference toxicants. Algal growth inhibition (72 h) showed no significant (P > 0.05) difference at HPCD concentrations up to and including 20 mM. HPCD presence did not influence the toxicity of the inorganic reference toxicant (ZnSO{sub 4}), with IC50 values of 0.82 {mu}M and 0.85 {mu}M, in the presence and absence of HPCD (20 mM), respectively. However, HPCD presence (20 mM) reduced the toxicity of 2,4-dichlorophenol and the herbicides diuron and isoproturon. These reductions were attributed to inclusion complex formation between the toxicants and the HPCD cavity. Liberation of complexed toxicants, by sample manipulation prior to toxicity assessment, is proposed to provide a sensitive, high throughput, bioassay that reflects compound bioaccessibility. - Compatibility of the biomimetic HPCD extraction method with algal cell growth inhibition bioassays to assess toxicity of reference toxicants and environmental relevant herbicides.

Real-time PCR for the early detection and quantification of Coxiella burnetii as an alternative to the murine bioassay.

Science.gov (United States)

Howe, Gerald B; Loveless, Bonnie M; Norwood, David; Craw, Philip; Waag, David; England, Marilyn; Lowe, John R; Courtney, Bernard C; Pitt, M Louise; Kulesh, David A

2009-01-01

Real-time PCR was used to analyze archived blood from non-human primates (NHP) and fluid samples originating from a well-controlled Q fever vaccine efficacy trial. The PCR targets were the IS1111 element and the com1 gene of Coxiella burnetii. Data from that previous study were used to evaluate real-time PCR as an alternative to the use of sero-conversion by mouse bioassay for both quantification and early detection of C. burnetii bacteria. Real-time PCR and the mouse bioassay exhibited no statistical difference in quantifying the number of microorganisms delivered in the aerosol challenge dose. The presence of C. burnetii in peripheral blood of non-human primates was detected by real-time PCR as early after exposure as the mouse bioassay with results available within hours instead of weeks. This study demonstrates that real-time PCR has the ability to replace the mouse bioassay to measure dosage and monitor infection of C. burnetii in a non-human primate model.

Estimation of uranium in bioassay samples of occupational workers by laser fluorimetry

International Nuclear Information System (INIS)

Suja, A.; Prabhu, S.P.; Sawant, P.D.; Sarkar, P.K.; Tiwari, A.K.; Sharma, R.

2010-01-01

A newly established uranium processing facility has been commissioned at BARC, Trombay. Monitoring of occupational workers at regulars intervals is essential to assess intake of uranium by the workers in this facility. The design and engineering safety features of the plant are such that there is very low probability of uranium getting air borne during normal operations. However, the leakages from the system during routine maintenance of the plant may result in intake of uranium by workers. As per the new biokinetic model for uranium, 63% of uranium entering the blood stream gets directly excreted in urine. Therefore, bioassay monitoring (urinalysis) was recommended for these workers. A group of 21 workers was selected for bioassay monitoring to assess the existing urinary excretion levels of uranium before the commencement of actual work. For this purpose, sample collection kit along with an instruction slip was provided to the workers. Bioassay samples received were wet ashed with conc. nitric acid and hydrogen peroxide to break down the metabolized complexes of uranium and it was co-precipitated with calcium phosphate. Separation of uranium from the matrix was done using ion exchange technique and final activity quantification in these samples was done using laser fluorimeter (Quantalase, Model No. NFL/02). Calibration of the laser fluorimeter is done using 10 ppb uranium standard (WHO, France Ref. No. 180000). Verification of the system performance is done by measuring concentration of uranium in the standards (1 ppb to 100 ppb). Standard addition method was followed for estimation of uranium concentration in the samples. Uranyl ions present in the sample get excited by pulsed nitrogen laser at 337.1 nm, and on de-excitation emit fluorescence light (540 nm) intensity which is measured by the PMT. To estimate the uranium in the bioassay samples, a known aliquot of the sample was mixed with 5% sodium pyrophosphate and fluorescence intensity was measured

Relaxations in spin glasses: Similarities and differences from ordinary glasses

International Nuclear Information System (INIS)

Ngai, K.L.; Rajagopal, A.K.; Huang, C.Y.

1984-01-01

Relaxation phenomena have become a major concern in the physics of spin glasses. There are certain resemblances of these relaxation properties to those of ordinary glasses. In this work, we compare the relaxation properties of spin glasses near the freezing temperature with those of glasses near the glass transition temperature. There are similarities between the two types of glasses. Moreover, the relaxation properties of many glasses and spin glasses are in conformity with two coupled ''universality'' relations predicted by a recent model of relaxations in condensed matter

Methods for conducting bioassays using embryos and larvae of Pacific herring, Clupea pallasi.

Science.gov (United States)

Dinnel, Paul A; Middaugh, Douglas P; Schwarck, Nathan T; Farren, Heather M; Haley, Richard K; Hoover, Richard A; Elphick, James; Tobiason, Karen; Marshall, Randall R

2011-02-01

The rapid decrease of several stocks of Pacific herring, Clupea pallasi, in Puget Sound, Washington, has led to concerns about the effects of industrial and nonpoint source contamination on the embryo and larval stages of this and related forage fish species. To address these concerns, the state of Washington and several industries have funded efforts to develop embryo and larval bioassay protocols that can be used by commercial laboratories for routine effluent testing. This article presents the results of research to develop herring embryo and larval bioassay protocols. Factors evaluated during protocol development included temperature, salinity, dissolved oxygen (DO), light intensity, photoperiod, larval feeding regimes, use of brine and artificial sea salts, gonad sources, collection methods, and egg quality.

Effects of Different Containers on Radioactivity Measurements using a Dose Calibrator with Special Reference to 111In and 123I.

Science.gov (United States)

Inoue, Yusuke; Abe, Yutaka; Kikuchi, Kei; Miyatake, Hiroki; Watanabe, Atsushi

2017-01-01

Low-energy characteristic x-rays emitted by 111 In and 123 I sources are easily absorbed by the containers of the sources, affecting radioactivity measurements using a dose calibrator. We examined the effects of different containers on the estimated activities. The radioactivities of 111 In, 123 I, 201 Tl, and 99m Tc were measured in containers frequently employed in clinical practice in Japan. The 111 In measurements were performed in the vials A and B of the 111 In-pentetreotide preparation kit and in the plastic syringe. The activities of 123 I-metaiodobenzylguanidine and 201 Tl chloride were measured in the prefilled glass syringes and plastic syringes. The milking vial, vial A, vial B, and plastic syringe were used to assay 99m Tc. For 111 In and 123 I, measurements were performed with and without a copper filter. The filter was inserted into the well of the dose calibrator to absorb low-energy x-rays. The relative estimate was defined as the ratio of the activity estimated with the dose calibrator to the standard activity. The estimated activities varied greatly depending on the container when 111 In and 123 I sources were assayed without the copper filter. The relative estimates of 111 In were 0.908, 1.072, and 1.373 in the vial A, vial B, and plastic syringe, respectively. The relative estimates of 123 I were 1.052 and 1.352 in the glass syringe and plastic syringe, respectively. Use of the copper filter eliminated the container-dependence in 111 In and 123 I measurements. Container-dependence was demonstrated in neither 201 Tl nor 99m Tc measurements. The activities of 111 In and 123 I estimated with a dose calibrator differ greatly among the containers. Accurate estimation may be attained using the container-specific correction factor or using the copper filter.

Kinetic microplate bioassays for relative potency of antibiotics improved by partial Least Square (PLS) regression.

Science.gov (United States)

Francisco, Fabiane Lacerda; Saviano, Alessandro Morais; Almeida, Túlia de Souza Botelho; Lourenço, Felipe Rebello

2016-05-01

Microbiological assays are widely used to estimate the relative potencies of antibiotics in order to guarantee the efficacy, safety, and quality of drug products. Despite of the advantages of turbidimetric bioassays when compared to other methods, it has limitations concerning the linearity and range of the dose-response curve determination. Here, we proposed to use partial least squares (PLS) regression to solve these limitations and to improve the prediction of relative potencies of antibiotics. Kinetic-reading microplate turbidimetric bioassays for apramacyin and vancomycin were performed using Escherichia coli (ATCC 8739) and Bacillus subtilis (ATCC 6633), respectively. Microbial growths were measured as absorbance up to 180 and 300min for apramycin and vancomycin turbidimetric bioassays, respectively. Conventional dose-response curves (absorbances or area under the microbial growth curve vs. log of antibiotic concentration) showed significant regression, however there were significant deviation of linearity. Thus, they could not be used for relative potency estimations. PLS regression allowed us to construct a predictive model for estimating the relative potencies of apramycin and vancomycin without over-fitting and it improved the linear range of turbidimetric bioassay. In addition, PLS regression provided predictions of relative potencies equivalent to those obtained from agar diffusion official methods. Therefore, we conclude that PLS regression may be used to estimate the relative potencies of antibiotics with significant advantages when compared to conventional dose-response curve determination. Copyright © 2016 Elsevier B.V. All rights reserved.

Method for the analysis of triadimefon and ethofumesate from dislodgeable foliar residues on turfgrass by solid-phase extraction and in-vial elution.

Science.gov (United States)

Runes, H B; Jenkins, J J; Field, J A

1999-08-01

Triadimefon, a fungicide, and ethofumesate, an herbicide, are commonly applied to turfgrass in the Pacific Northwest, resulting in foliar residues. A simple and rapid method was developed to determine triadimefon and ethofumesate concentrations from dislodgeable foliar residues on turfgrass. Turfgrass samples were washed, and wash water containing surfactant (a 0.126% solution) was collected for residue analysis. This analytical method utilizes a 25 mm C(8) Empore disk and in-vial elution to quantitatively determine triadimefon and ethofumesate in 170 mL aqueous samples. The analytes were eluted by placing the disk in a 2 mL autosampler vial with 980 microL of ethyl acetate and 20 microL of 2-chlorolepidine, the internal standard, for analysis by GC/MS. The method quantitation limits are 0.29 microg/L for ethofumesate and 0.59 microg/L for triadimefon. The method detection limits are 0.047 microg/L and 0.29 microg/L for ethofumesate and triadimefon, respectively. Concentrations of triadimefon and ethofumesate from dislodgeable foliar residues from a field study are reported.

Scintillating-Glass-Fiber neutron sensors, their application and performance for plutonium detection and monitoring

International Nuclear Information System (INIS)

Seymour, R.S.; Richardson, B.; Morichi, M.; Bliss, M.; Craig, R.A.; Sunberg, D.S.

1998-01-01

Most neutron detection sensors presently employ 3 He gas-filled detectors. Despite their excellent performance and widespread use, there are significant limitations to this technology. A significant alternative neutron sensor utilizing neutron-active material incorporated into a glass scintillator is presented that offers novel commercial sensors not possible or practical with gas tube technology. The scintillating optical fiber permits sensors with a multitude of sizes ranging from devices of a single fiber of 150μm to sensors with tens of thousands of fibers with areas as large as 5m 2 depending on the neutron flux to be measured. A second significant advantage is the use of high-speed electronics that allow a greater dynamic range, not possible with gas detectors. These sensors are flexible, conformable and less sensitive to vibration that optimizes the source-to-detector geometry and provides robust performance in field applications. The glass-fibers are sensitive to both gamma rays and neutrons. However the coincidence electronics are optimized for neutron to gamma ray discrimination allowing very sensitive measurements with a low false-alarm rate. Applications include SNM surveillance, material control and accountability (MC and A), safeguard inspections, Pu health physics / bioassay and environmental characterization. (author)

Evaporation rate in containers used for storing radioactive tracer solutions

International Nuclear Information System (INIS)

Gascon, J.L.

2002-01-01

In radiochemical analysis, the storage of a tracer solution is an important issue to bear in mind. The evaporation of the tracer solution depends on the type of container used for storing. Evaporation rate in four kinds of containers, i.e., flame-sealed glass ampoule, sealed glass flask, flame-sealed polyethylene ampoule and screw glass vial was studied. It is concluded that the evaporation rate depends on the system of closing. (author)

Glass science tutorial: Lecture No. 7, Waste glass technology for Hanford

International Nuclear Information System (INIS)

Kruger, A.A.

1995-07-01

This paper presents the details of the waste glass tutorial session that was held to promote knowledge of waste glass technology and how this can be used at the Hanford Reservation. Topics discussed include: glass properties; statistical approach to glass development; processing properties of nuclear waste glass; glass composition and the effects of composition on durability; model comparisons of free energy of hydration; LLW glass structure; glass crystallization; amorphous phase separation; corrosion of refractories and electrodes in waste glass melters; and glass formulation for maximum waste loading

Mechanical failure and glass transition in metallic glasses

International Nuclear Information System (INIS)

Egami, T.

2011-01-01

Research highlights: → We review the recent results of molecular dynamics simulations on metallic glasses. → They show the equivalence of mechanical failure and glass transition. → We discuss the microscopic mechanism behind this equivalence. → We show that the density of defects in metallic glasses is as high as a quarter. → Our concepts about the defect state in glasses need to be changed. - Abstract: The current majority view on the phenomenon of mechanical failure in metallic glasses appears to be that it is caused by the activity of some structural defects, such as free-volumes or shear transformation zones, and the concentration of such defects is small, only of the order of 1%. However, the recent results compel us to revise this view. Through molecular dynamics simulation it has been shown that mechanical failure is the stress-induced glass transition. According to our theory the concentration of the liquid-like sites (defects) is well over 20% at the glass transition. We suggest that the defect concentration in metallic glasses is actually very high, and percolation of such defects causes atomic avalanche and mechanical failure. In this article we discuss the glass transition, mechanical failure and viscosity from such a point of view.

Tritiated Dust Levitation by Beta Induced Static Charge

International Nuclear Information System (INIS)

Skinner, C.H.; Gentile, C.A.; Ciebiera, L.; Langish, S.

2003-01-01

Tritiated particles have been observed to spontaneously levitate under the influence of a static electric field. Tritium containing co-deposits were mechanically scraped from tiles that had been used in the Tokamak Fusion Test Reactor (TFTR) inner limiter during the deuterium-tritium campaign and were placed in a glass vial. On rubbing the plastic cap of the vial a remarkable ''fountain'' of particles was seen inside the vial. Particles from an unused tile or from a TFTR co-deposit formed during deuterium discharges did not exhibit this phenomenon. It appears that tritiated particles are more mobile than other particles and this should be considered in assessing tokamak accident scenarios and in occupational safety

Intervención estatal, desempeño empresario y ámbitos privilegiados de acumulación. El caso del sector vial durante la última dictadura militar, Argentina (1976-1981

Directory of Open Access Journals (Sweden)

LUCAS DANIEL IRAMAIN

2013-05-01

Full Text Available Las políticas destinadas a las obras públicas viales en la Argentina durante el lapso 1976-1981, constituyen ejemplos, paradójicos, de la creciente participación económica del Estado, en el marco de un proceso político-institucional signado por un discurso fuertemente liberal y contrario a la expansión de la actividad estatal. En ese sentido, los objetivos de este trabajo son caracterizar los rasgos más significativos de la intervención económica estatal en relación a la construcción de obras públicas viales durante el lapso 1976-1981 y analizar bajo ese mismo período el desempeño económico de las principales empresas intervinientes en el mercado vial. La consecución de estos dos propósitos, a su vez, permitirá establecer si durante esos años se generaron las condiciones propicias para la configuración de un ámbito privilegiado de acumulación (Castellani, 2006, en torno a las obras viales. Abstract The policies oriented to public road-building works during 1976-1981 in Argentina, constitute paradoxical examples of the increasing economic participation of the Estate, within the framework of a political and institutional process signed by a strong liberal speech, opposed to the expansion of Estate activity. Hence, the objectives of this work are to characterize the most significant aspects of the estate economic intervention in relation to public road-building works from 1976 to 1981 and to analyze the economic performance of the main companies participating in the road-market during that period. At the same time, the completion of these goals will allow to establish whether a configuration of a privileged accumulation space (Castellani, 2006 around road-works took place during those years.

Problems associated with scintillation counting of NaH14CO3 and gel suspension counting of Ba14CO3

International Nuclear Information System (INIS)

MacRae, J.C.; Wilson, S.

1978-01-01

Liquid NaH 14 CO 3 was assayed in emulsion-type (NE260 and Unisolve) and dioxan-based (NE250) scintillation cocktails contained in glass or polyethylene vials kept at 2 0 or 24-30 0 C. Different particle size ranges of standard Ba 14 CO 3 were assayed by gel suspension counting in Cabosil scintillation cocktail and in NE260 following solubilisation in EDTA-tetrasodium salt. Initial detectable activities of NaH 14 CO 3 in glass and polyethylene vials in NE250, NE260 and Unisolve were 97 and 96, 68 and 83, 71 and 89% of the true value respectively. Subsequent losses of activity over 7 days with the emulsion-type scintillators was greater from the polyethylene vials. Addition of phenylethylamine to the NE260 and Unisolve cocktails gave the true activity levels for all vials with no loss of activity over 6 days. When different particle size ranges of Standard Ba 14 CO 3 were suspended in Cabosil scintillation cocktail there was considerable variation in counting efficiency (77-88%) with little relationship between particle size and counting efficiency. The relationship between counting efficiency and channels ratio was not sufficiently precise for predictive purposes. Solubilisation of Ba 14 CO 3 in EDTA-tetrasodium salt gave similar counting efficiency and channels ratio values for all samples. (U.K.)

Enhancing the response of CALUX and CAFLUX cell bioassays for quantitative detection of dioxin-like compounds

Science.gov (United States)

ZHAO, Bin; BASTON, David S.; KHAN, Elaine; SORRENTINO, Claudio; DENISON, Michael S.

2011-01-01

Reporter genes produce a protein product in transfected cells that can be easily measured in intact or lysed cells and they have been extensively used in numerous basic and applied research applications. Over the past 10 years, reporter gene assays have been widely accepted and used for analysis of 2,3,7,8-tetrachlorodibenzo-p-dioxin and related dioxin-like compounds in various types of matrices, such as biological, environmental, food and feed samples, given that high-resolution instrumental analysis techniques are impractical for large-scale screening analysis. The most sensitive cell-based reporter gene bioassay systems developed are the mechanism-based CALUX (Chemically Activated Luciferase Expression) and CAFLUX (Chemically Activated Fluorescent Expression) bioassays, which utilize recombinant cell lines containing stably transfected dioxin (AhR)-responsive firefly luciferase or enhanced green fluorescent protein (EGFP) reporter genes, respectively. While the current CALUX and CAFLUX bioassays are very sensitive, increasing their lower limit of sensitivity, magnitude of response and dynamic range for chemical detection would significantly increase their utility, particularly for those samples that contain low levels of dioxin-like HAHs (i.e., serum). In this study, we report that the addition of modulators of cell signaling pathways or modification of cell culture conditions results in significant improvement in the magnitude and overall responsiveness of the existing CALUX and CAFLUX cell bioassays. PMID:21394221

Cleavable DNA-protein hybrid molecular beacon: A novel efficient signal translator for sensitive fluorescence anisotropy bioassay.

Science.gov (United States)

Hu, Pan; Yang, Bin

2016-01-15

Due to its unique features such as high sensitivity, homogeneous format, and independence on fluorescent intensity, fluorescence anisotropy (FA) assay has become a hotspot of study in oligonucleotide-based bioassays. However, until now most FA probes require carefully customized structure designs, and thus are neither generalizable for different sensing systems nor effective to obtain sufficient signal response. To address this issue, a cleavable DNA-protein hybrid molecular beacon was successfully engineered for signal amplified FA bioassay, via combining the unique stable structure of molecular beacon and the large molecular mass of streptavidin. Compared with single DNA strand probe or conventional molecular beacon, the DNA-protein hybrid molecular beacon exhibited a much higher FA value, which was potential to obtain high signal-background ratio in sensing process. As proof-of-principle, this novel DNA-protein hybrid molecular beacon was further applied for FA bioassay using DNAzyme-Pb(2+) as a model sensing system. This FA assay approach could selectively detect as low as 0.5nM Pb(2+) in buffer solution, and also be successful for real samples analysis with good recovery values. Compatible with most of oligonucleotide probes' designs and enzyme-based signal amplification strategies, the molecular beacon can serve as a novel signal translator to expand the application prospect of FA technology in various bioassays. Copyright © 2015 Elsevier B.V. All rights reserved.

Silicate glasses

International Nuclear Information System (INIS)

Lutze, W.

1988-01-01

Vitrification of liquid high-level radioactive wastes has received the greatest attention, world-wide, compared to any other HLW solidification process. The waste form is a borosilicate-based glass. The production of phosphate-based glass has been abandoned in the western world. Only in the Soviet Union are phosphate-based glasses still being developed. Vitrification techniques, equipment and processes and their remote operation have been developed and studied for almost thirty years and have reached a high degree of technical maturity. Industrial demonstration of the vitrification process has been in progress since 1978. This chapter is a survey of world-wide research and development efforts in nuclear waste glasses and its production technology. The principal glasses considered are silicate glasses which contain boron, i.e., borosilicate glasses

Genotoxicity monitoring of industrial wastes using plant bioassays and management through vermitechnology: A review

Directory of Open Access Journals (Sweden)

Sartaj Ahmad Bhat

2017-10-01

Full Text Available The main objective of this review was to summarize and present a comprehensive account of the cytotoxic, genotoxic and mutagenic potential of various industrial wastes/sludges using some well-known plant bioassays followed by their bioremediation using vermitechnology. Industries are the main origin of discharges of various types of chemical wastes and are the main causes of environmental degradation. The direct application of industrial sludges could also harm the local biota. The genotoxicity of industrial sludges is assessed using various plant bioassays (for example Allium cepa, Vicia faba and these bioassays are comparatively more sensitive and cost-effective compared to other in-vitro genotoxicity bioassays. In addition, the materials used for toxicity evaluation are easily available and are being routinely used for the monitoring of environmental pollution. In most studies, the increases in root length and mitotic index, as well as the decrease in chromosomal aberrations in post vermicomposted sludges/wastes indicate that earthworms have the ability to reduce the ecotoxicogenetic effects of sludges/wastes. Post vermicompost is considered an excellent material of a homogenous nature as it has reduced levels of contaminants and holds more nutrients over a longer time without affecting the environment. The biotransformation potential of earthworms and their ability to detoxify most of the heavy metals in industrial sludges is because of their strong metabolic system and the involvement of diverse intestinal microflora and chloragocytic cells that reduce toxic forms to nontoxic forms. This unique ability of earthworms confirms the effectiveness of vermitechnology in reducing the toxicity of industrial wastes. Keywords: Allium cepa, Earthworm, Industrial sludge, Toxicity, Vermicomposting

Fathead minnows (Pimephales promelas) and goldfish (Carassius auratus) as standard fish in bioassays and their reaction to potential reference toxicants

Energy Technology Data Exchange (ETDEWEB)

Adelman, I.R.; Smith, L.L. Jr.

1976-02-01

Fathead minnows (Pimephales promelas) and goldfish (Carassius auratus) were compared for their suitability as standard bioassay fish. Both species showed the same variability of bioassay results when tested with four toxicants. Fathead minnows are recommended on the basis of their small size and on their capability for use in complete life cycle tests. On the basis of minimum variability of bioassay results, sodium chloride was superior for use as a reference toxicant. Both sodium chloride and pentachlorophenol seemed capable of detecting abnormal fish. On the basis of seven listed criteria either sodium chloride or pentachlorophenol would be acceptable as a reference toxicant.

High-Level Waste Glass Formulation Model Sensitivity Study 2009 Glass Formulation Model Versus 1996 Glass Formulation Model

International Nuclear Information System (INIS)

Belsher, J.D.; Meinert, F.L.

2009-01-01

This document presents the differences between two HLW glass formulation models (GFM): The 1996 GFM and 2009 GFM. A glass formulation model is a collection of glass property correlations and associated limits, as well as model validity and solubility constraints; it uses the pretreated HLW feed composition to predict the amount and composition of glass forming additives necessary to produce acceptable HLW glass. The 2009 GFM presented in this report was constructed as a nonlinear optimization calculation based on updated glass property data and solubility limits described in PNNL-18501 (2009). Key mission drivers such as the total mass of HLW glass and waste oxide loading are compared between the two glass formulation models. In addition, a sensitivity study was performed within the 2009 GFM to determine the effect of relaxing various constraints on the predicted mass of the HLW glass.

Design and Proof-of-Concept Use of a Circular PMMA Platform with 16-Well Sample Capacity for Microwave-Accelerated Bioassays.

Science.gov (United States)

Mohammed, Muzaffer; Aslan, Kadir

2013-01-01

We demonstrate the design and the proof-of-concept use of a new, circular poly(methyl methacrylate)-based bioassay platform (PMMA platform), which affords for the rapid processing of 16 samples at once. The circular PMMA platform (5 cm in diameter) was coated with a silver nanoparticle film to accelerate the bioassay steps by microwave heating. A model colorimetric bioassay for biotinylated albumin (using streptavidin-labeled horse radish peroxidase) was performed on the PMMA platform coated with and without silver nanoparticles (a control experiment), and at room temperature and using microwave heating. It was shown that the simulated temperature profile of the PMMA platform during microwave heating were comparable to the real-time temperature profile during actual microwave heating of the constructed PMMA platform in a commercial microwave oven. The model colorimetric bioassay for biotinylated albumin was successfully completed in ~2 min (total assay time) using microwave heating, as compared to 90 min at room temperature (total assay time), which indicates a ~45-fold decrease in assay time. Our PMMA platform design afforded for significant reduction in non-specific interactions and low background signal as compared to non-silvered PMMA surfaces when employed in a microwave-accelerated bioassay carried out in a conventional microwave cavity.

Sampling method, storage and pretreatment of sediment affect AVS concentrations with consequences for bioassay responses

Energy Technology Data Exchange (ETDEWEB)

Lange, H.J. de [Aquatic Ecology and Water Quality Management Group, Wageningen University, Wageningen University and Research Centre, P.O. Box 8080, 6700 DD, Wageningen (Netherlands); Centre for Ecosystem Studies, Alterra, Wageningen University and Research Centre, P.O. Box 47, 6700 AA, Wageningen (Netherlands)], E-mail: marieke.delange@wur.nl; Griethuysen, C. van; Koelmans, A.A. [Aquatic Ecology and Water Quality Management Group, Wageningen University, Wageningen University and Research Centre, P.O. Box 8080, 6700 DD, Wageningen (Netherlands)

2008-01-15

Sediment treatment and sediment storage may alter sediment toxicity, and consequently biotic response. Purpose of our study was to combine these three aspects (treatment-toxicity-biotic response) in one integrated approach. We used Acid Volatile Sulfide (AVS) concentrations as a proxy of the disturbance of the sediment. AVS and Simultaneously Extracted Metal (SEM) concentrations were compared to bioassay responses with the freshwater benthic macroinvertebrate Asellus aquaticus. Storage conditions and sediment treatment affected AVS but not SEM levels. AVS can be used as a proxy for sediment disturbance. The best way to pretreat the sediment for use in a bioassay in order to maintain initial AVS conditions was to sample the sediment with an Ekman grab, immediately store it in a jar without headspace, and freeze it as soon as possible. In a survey using seven different sediments, bioassay responses of A. aquaticus were correlated with SEM and AVS characteristics. - Change in AVS is a good proxy for sediment disturbance and combined with SEM it can be used as a suitable predictor for biotic effects of sediment contamination.

High performance wash-free magnetic bioassays through microfluidically enhanced particle specificity.

Science.gov (United States)

Bechstein, Daniel J B; Lee, Jung-Rok; Ooi, Chin Chun; Gani, Adi W; Kim, Kyunglok; Wilson, Robert J; Wang, Shan X

2015-06-30

Magnetic biosensors have emerged as a sensitive and versatile platform for high performance medical diagnostics. These magnetic biosensors require well-tailored magnetic particles as detection probes, which need to give rise to a large and specific biological signal while showing very low nonspecific binding. This is especially important in wash-free bioassay protocols, which do not require removal of particles before measurement, often a necessity in point of care diagnostics. Here we show that magnetic interactions between magnetic particles and magnetized sensors dramatically impact particle transport and magnetic adhesion to the sensor surfaces. We investigate the dynamics of magnetic particles' biomolecular binding and magnetic adhesion to the sensor surface using microfluidic experiments. We elucidate how flow forces can inhibit magnetic adhesion, greatly diminishing or even eliminating nonspecific signals in wash-free magnetic bioassays, and enhancing signal to noise ratios by several orders of magnitude. Our method is useful for selecting and optimizing magnetic particles for a wide range of magnetic sensor platforms.

Eubacterium brachy - Reactivity in In Vitro Bone Resorptive Bioassay,

Science.gov (United States)

1983-02-10

Center Washington, D. C . 20307 If Eubacterium brachy - Reactivity in In Vitro Bone Resorptive Bioassay 1. ABSTRACT Recent studies have demonstrated an...Relative distribution of bacteria at clinically healthy and periodontally diseased sites in humans. J Clin Periodontal 5:115, 1978. 3. Evian, C ...applied foreign protein into rat gingiva. J Periodont Res 6:89, 1971. 21. Gaffer, A., Coleman, E.J., and Marcussen, H.W.: Penetration of dental plaque

Continuous flow bioassay method to evaluate the effects of outboard motor exhausts and selected aromatic toxicants on fish. [Carassius auratus

Energy Technology Data Exchange (ETDEWEB)

Brenniman, G. (Univ. of Illinois, Chicago); Hartung, R.; Weber, W.J. Jr.

1976-01-01

A continuous flow bioassay system was designed to measure the effects of outboard motor exhaust (OME) emissions and selected volatile and evaporative aromatic toxicants on goldfish (Carassius auratus). Continuous flow bioassays were run for 24, 48, 72, 96, and 720 h to determine lethal concentrations for 50 percent of individuals (LC 50's) for leaded OME, non-leaded OME, toluene, xylene, and 1,3,5 trimethylbenzene, the three individual compounds having been identified as significant aromatic components of OME. The 96 h LC-50's for these substances were found to be 171, 168, 23, 17, and 13 ppm, respectively. The values of 171 and 168 ppm for the two OME's are given in terms of gallons of fuel burned per million gallons of water. The continuous flow bioassay method was demonstrated to be a more reliable indicator of the effects of OME pollutants on aquatic organisms than is the static bioassay method.

Assessment of the genotoxicity of 137Cs radiation using Vicia-micronucleus, Tradescantia-micronucleus and Tradescantia-stamen-hair mutation bioassays.

Science.gov (United States)

Minouflet, Marion; Ayrault, Sophie; Badot, Pierre-Marie; Cotelle, Sylvie; Ferard, Jean-François

2005-01-01

Since the middle of the 20th century, ionizing radiations from radioactive isotopes including 137Cs have been investigated to determine their genotoxic impact on living organisms. The present study was designed to compare the effectiveness of three plant bioassays to assess DNA damage induced by low doses of 137Cs: Vicia-micronucleus test (Vicia-MCN), Tradescantia-micronucleus test (Trad-MCN) and Tradescantia-stamen-hair mutation test (Trad-SH) were used. Vicia faba (broad bean) and Tradescantia clone 4430 (spiderwort) were exposed to 137Cs according to different scenarios: external and internal (contamination) irradiations. Experiments were conducted with various levels of radioactivity in solution or in soil, using solid or liquid 137Cs sources. The three bioassays showed different sensitivities to the treatments. Trad-MCN appeared to be the most sensitive test (significative response from 1.5 kBq/200 ml after 30 h of contamination). Moreover, at comparable doses, internal irradiations led to larger effects for the three bioassays. These bioassays are effective tests for assessing the genotoxic effects of radioactive 137Cs pollution.

Assessment of the genotoxicity of 137Cs radiation using Vicia-micronucleus, Tradescantia-micronucleus and Tradescantia-stamen-hair mutation bioassays

International Nuclear Information System (INIS)

Minouflet, Marion; Ayrault, Sophie; Badot, Pierre-Marie; Cotelle, Sylvie; Ferard, Jean-Francois

2005-01-01

Since the middle of the 20th century, ionizing radiations from radioactive isotopes including 137 Cs have been investigated to determine their genotoxic impact on living organisms. The present study was designed to compare the effectiveness of three plant bioassays to assess DNA damage induced by low doses of 137 Cs: Vicia-micronucleus test (Vicia-MCN), Tradescantia-micronucleus test (Trad-MCN) and Tradescantia-stamen-hair mutation test (Trad-SH) were used. Vicia faba (broad bean) and Tradescantia clone 4430 (spiderwort) were exposed to 137 Cs according to different scenarios: external and internal (contamination) irradiations. Experiments were conducted with various levels of radioactivity in solution or in soil, using solid or liquid 137 Cs sources. The three bioassays showed different sensitivities to the treatments. Trad-MCN appeared to be the most sensitive test (significative response from 1.5 kBq/200 ml after 30 h of contamination). Moreover, at comparable doses, internal irradiations led to larger effects for the three bioassays. These bioassays are effective tests for assessing the genotoxic effects of radioactive 137 Cs pollution

Optimized Synthesis of Foam Glass from Recycled CRT Panel Glass

DEFF Research Database (Denmark)

Petersen, Rasmus Rosenlund; König, Jakob; Yue, Yuanzheng

Most of the panel glass from cathode ray tubes (CRTs) is landfilled today. Instead of landfilling, the panel glass can be turned into new environment-friendly foam glass. Low density foam glass is an effective heat insulating material and can be produced just by using recycle glass and foaming...... additives. In this work we recycle the CRT panel glass to synthesize the foam glass as a crucial component of building and insulating materials. The synthesis conditions such as foaming temperature, duration, glass particle size, type and concentrations of foaming agents, and so on are optimized...... by performing systematic experiments. In particular, the concentration of foaming agents is an important parameter that influences the size of bubbles and the distribution of bubbles throughout the sample. The foam glasses are characterised regarding density and open/closed porosity. Differential scanning...

Evaluación de factores camión de los vehículos comerciales de carga que circulan por la red vial principal colombiana

Directory of Open Access Journals (Sweden)

Luis F. Macea

2013-01-01

Full Text Available La estimación del tránsito es uno de los aspectos más importantes en el análisis y diseño estructural de pavimentos y para su adecuada determinación se hace necesario disponer de valores de factor camión actualizados. En el presente estudio se evaluaron los factores camión de los vehículos comerciales de carga de la red vial primaria de Colombia. Con este objetivo, en el año 2011 se realizaron treinta y ocho operativos móviles de pesaje de ejes en carretera, localizados en distintos puntos estratégicos de la red vial nacional. Como resultado se obtuvo, a través de procedimientos estadísticos, factores camión actualizados y representativos para cada tipo de camión que circula en las vías analizadas. Estos factores camión podrían ser utilizados en el diseño de tramos carreteros con características socioeconómicas similares a aquellas de las vías evaluadas. De igual forma, se encontró que a nivel nacional la flota vehicular de carga está compuesta por los camiones tipo C3-S3, C2, C3-S2, C3 y C2-S2 con una distribución del 36%, 35%, 13%, 11% y 5%, respectivamente. Adicionalmente, se observó que los camiones C3 y C3-S3 son los que mayor daño le causan a la infraestructura vial colombiana, ya que se encuentran circulando excesivamente sobrecargados en algunos tramos departamentales del país.

Bioassay directed identification of natural aryl hydrocarbon-receptor agonists in marmalade

NARCIS (Netherlands)

Ede, van K.I.; Li, A.; Antunes Fernandes, E.C.; Mulder, P.P.J.; Peijnenburg, A.A.C.M.; Hoogenboom, L.A.P.

2008-01-01

Citrus fruit and citrus fruit products, like grapefruit, lemon and marmalade were shown to contain aryl hydrocarbon receptor (AhR) agonists, as detected with the DR CALUX® bioassay. This is of interest regarding the role of the Ah-receptor pathway in the adverse effects of dioxins, PCBs and other

Guidance document for prepermit bioassay testing of low-level radioactive waste

International Nuclear Information System (INIS)

Anderson, S.L.; Harrison, F.L.

1990-11-01

In response to the mandate of Public Law 92-532, the Marine Protection, Research, and Sanctuaries Act (MPRSA) of 1972, as amended, the Environmental Protection Agency (EPA) has developed a program to promulgate regulations and criteria to control the ocean disposal of radioactive wastes. The EPA seeks to understand the mechanisms for biological response of marine organisms to the low levels of radioactivity that may arise from the release of these wastes as a result of ocean-disposal practices. Such information will play an important role in determining the adequacy of environmental assessments provided to the EPA in support of any disposal permit application. Although the EPA requires packaging of low-level radioactive waste to prevent release during radiodecay of the materials, some release of radioactive material into the deep-sea environment may occur when a package deteriorates. Therefore, methods for evaluating the impact on biota are being evaluated. Mortality and phenotypic responses are not anticipated at the expected low environmental levels that might occur if radioactive materials were released from the low-level waste packages. Therefore, traditional bioassay systems are unsuitable for assessing sublethal effects on biota in the marine environment. The EPA Office of Radiation Programs (ORP) has had an ongoing program to examine sublethal responses to radiation at the cellular level, using cytogenetic end points. This technical guidance report represents prepermit bioassay procedures that potentially may be applicable to the assessment of effects from a mixture of radionuclides that could be released from a point source at the ocean bottom. Methodologies along with rationale and a discussion of uncertainty are presented for the sediment benthic bioassay protocols identified in this report

GHSI emergency radionuclide bioassay laboratory network - summary of the second exercise

International Nuclear Information System (INIS)

Li, Chunsheng; Ko, Raymond; Quayle, Debora; Sadi, Baki; Bartizel, Christine; Battisti, Paolo; Boettger, Axel; Bouvier, Celine; Paquet, Francois; CapoteCuellar, Antonio; Carr, Zhanat; Hammond, Derek; Hartmann, Martina; Heikkinen, Tarja; Jones, Robert L.; Kim, Eunjoo; Koga, Roberto; Kukhta, Boris; Mitchell, Lorna; Morhard, Ryan; Rulik, Petr; Sergei, Aleksanin; Sierra, Inmaculada; Oliveira Sousa, Wandersonde; Szabo, Gyula

2017-01-01

The Global Health Security Initiative (GHSI) established a laboratory network within the GHSI community to develop collective surge capacity for radionuclide bioassay in response to a radiological or nuclear emergency as a means of enhancing response capability, health outcomes and community resilience. GHSI partners conducted an exercise in collaboration with the WHO Radiation Emergency Medical Preparedness and Assistance Network and the IAEA Response and Assistance Network, to test the participating laboratories (18) for their capabilities in in vitro assay of biological samples, using a urine sample spiked with multiple high-risk radionuclides ( 90 Sr, 106 Ru, 137 Cs, and 239 Pu). Laboratories were required to submit their reports within 72 h following receipt of the sample, using a pre-formatted template, on the procedures, methods and techniques used to identify and quantify the radionuclides in the sample, as well as the bioassay results with a 95% confidence interval. All of the participating laboratories identified and measured all or some of the radionuclides in the sample. However, gaps were identified in both the procedures used to assay multiple radionuclides in one sample, as well as in the methods or techniques used to assay specific radionuclides in urine. Two-third of the participating laboratories had difficulties in determining all the radionuclides in the sample. Results from this exercise indicate that challenges remain with respect to ensuring that results are delivered in a timely, consistent and reliable manner to support medical interventions. Laboratories within the networks are encouraged to work together to develop and maintain collective capabilities and capacity for emergency bioassay, which is an important component of radiation emergency response. (authors)

Guidance document for prepermit bioassay testing of low-level radioactive waste

Energy Technology Data Exchange (ETDEWEB)

Anderson, S.L.; Harrison, F.L.

1990-11-01

In response to the mandate of Public Law 92-532, the Marine Protection, Research, and Sanctuaries Act (MPRSA) of 1972, as amended, the Environmental Protection Agency (EPA) has developed a program to promulgate regulations and criteria to control the ocean disposal of radioactive wastes. The EPA seeks to understand the mechanisms for biological response of marine organisms to the low levels of radioactivity that may arise from the release of these wastes as a result of ocean-disposal practices. Such information will play an important role in determining the adequacy of environmental assessments provided to the EPA in support of any disposal permit application. Although the EPA requires packaging of low-level radioactive waste to prevent release during radiodecay of the materials, some release of radioactive material into the deep-sea environment may occur when a package deteriorates. Therefore, methods for evaluating the impact on biota are being evaluated. Mortality and phenotypic responses are not anticipated at the expected low environmental levels that might occur if radioactive materials were released from the low-level waste packages. Therefore, traditional bioassay systems are unsuitable for assessing sublethal effects on biota in the marine environment. The EPA Office of Radiation Programs (ORP) has had an ongoing program to examine sublethal responses to radiation at the cellular level, using cytogenetic end points. This technical guidance report represents prepermit bioassay procedures that potentially may be applicable to the assessment of effects from a mixture of radionuclides that could be released from a point source at the ocean bottom. Methodologies along with rationale and a discussion of uncertainty are presented for the sediment benthic bioassay protocols identified in this report.

Review of Bioassays for Monitoring Fate and Transport ofEstrogenic Endocrine Disrupting Compounds in Water

Energy Technology Data Exchange (ETDEWEB)

CGCampbell@lbl.gov

2004-01-30

Endocrine disrupting compounds (EDCs) are recognizedcontaminants threatening water quality. Despite efforts in sourceidentification, few strategies exist for characterization or treatment ofthis environmental pollution. Given that there are numerous EDCs that cannegatively affect humans and wildlife, general screening techniques likebioassays and biosensors provide an essential rapid and intensiveanalysis capacity. Commonly applied bioassays include the ELISA and YESassays, but promising technologies include ER-CALUXa, ELRA, Endotecta,RIANA, and IR-bioamplification. Two biosensors, Endotecta and RIANA, arefield portable using non-cellular biological detection strategies.Environmental management of EDCs in water requires integration ofbiosensors and bioassays for monitoring and assessment.

Recycling of Glass

DEFF Research Database (Denmark)

Christensen, Thomas Højlund; Damgaard, Anders

2011-01-01

Glass is used for many purposes, but in the waste system glass is predominantly found in terms of beverage and food containers with a relatively short lifetime before ending up in the waste. Furthermore there is a large amount of flat glass used in building materials which also ends up in the waste...... system; this glass though has a long lifetime before ending up in the waste. Altogether these product types add up to 82% of the production of the European glass industry (IPCC, 2001). Recycling of glass in terms of cleaning and refilling of bottles as well as the use of broken glass in the production...... of new glass containers is well established in the glass industry. This chapter describes briefly howglass is produced and howwaste glass is recycled in the industry. Quality requirements and use of recycled products are discussed, as are the resource and environmental issues of glass recycling....

Development of acute and chronic sediment bioassays with the harpacticoid copepod Quinquelaophonte sp.

Science.gov (United States)

Stringer, Tristan J; Glover, Chris N; Keesing, Vaughan; Northcott, Grant L; Gaw, Sally; Tremblay, Louis A

2014-01-01

Reliable environmentally realistic bioassay methodologies are increasingly needed to assess the effects of environmental pollution. This study describes two estuarine sediment bioassays, one acute (96 h) and one chronic (14 d), with the New Zealand harpacticoid copepod Quinquelaophonte sp. utilising behavioural and reproductive endpoints. Spiked sediments were used to expose Quinquelaophonte sp. to three reference compounds representing important categories of estuarine chemical stressors: zinc (a metal), atrazine (a pesticide), and phenanthrene (a polycyclic aromatic hydrocarbon). Acute-to-chronic ratios (ACR) were used to further characterise species responses. Acute sediment (sandy and low total organic content) 96 h EC50 values for the sublethal inhibition of mobility for zinc, atrazine and phenanthrene were 137, 5.4, and 2.6 µg/g, respectively. The chronic EC50 values for inhibition of reproduction (total offspring) were 54.5, 0.0083, and 0.067 µg/g for zinc, atrazine, and phenanthrene, respectively. For phenanthrene, a potentially novel mode of action was identified on reproduction. Quinquelaophonte sp. was found to be more sensitive than several other estuarine species indicating choice of test organism is important to characterising the effects of environmentally relevant levels of contamination. The bioassay sediment results demonstrate the sensitivity and suitability of Quinquelaophonte sp. as a tool for the assessment use of estuarine health. © 2013 Published by Elsevier Inc.

NEW ERBIUM DOPED ANTIMONY GLASSES FOR LASER AND GLASS AMPLIFICATION

Directory of Open Access Journals (Sweden)

B. Tioua

2015-07-01

Full Text Available Because of the special spectroscopic properties of the rare earth ions, rare earth doped glasses are widely used in bulk and fiber lasers or amplifiers. The modelling of lasers and searching for new laser transitions require a precise knowledge of the spectroscopic properties of rare earth ions in different host glasses. In this poster will offer new doped erbium glasses synthesized in silicate crucibles were obtained in the combination Sb2O3-WO3-Na2O. Several properties are measured and correlated with glass compositions. The absorption spectral studies have been performed for erbium doped glasses. The intensities of various absorption bands of the doped glasses are measured and the Judd-Ofelt parameters have been computed. From the theory of Judd-Ofelt, various radiative properties, such as transition probability, branching ratio and radiative life time for various emission levels of these doped glasses have been determined and reported. These results confirm the ability of antimony glasses for glass amplification.

Influence of Glass Property Restrictions on Hanford HLW Glass Volume

International Nuclear Information System (INIS)

Kim, Dong-Sang; Vienna, John D.

2001-01-01

A systematic evaluation of Hanford High-Level Waste (HLW) loading in alkali-alumino-borosilicate glasses was performed. The waste feed compositions used were obtained from current tank waste composition estimates, Hanford's baseline retrieval sequence, and pretreatment processes. The waste feeds were sorted into groups of like composition by cluster analysis. Glass composition optimization was performed on each cluster to meet property and composition constraints while maximizing waste loading. Glass properties were estimated using property models developed for Hanford HLW glasses. The impacts of many constraints on the volume of HLW glass to be produced at Hanford were evaluated. The liquidus temperature, melting temperature, chromium concentration, formation of multiple phases on cooling, and product consistency test response requirements for the glass were varied one- or many-at-a-time and the resultant glass volume was calculated. This study shows clearly that the allowance of crystalline phases in the glass melter can significantly decrease the volume of HLW glass to be produced at Hanford.

Phase transitions and glass transition in a hyperquenched silica–alumina glass

DEFF Research Database (Denmark)

Zhang, Y.F.; Zhao, D.H.; Yue, Yuanzheng

2017-01-01

We investigate phase transitions, glass transition, and dynamic behavior in the hyperquenched 69SiO2–31Al2O3 (mol%) glass (SA glass). Upon reheating, the SA glass exhibits a series of thermal responses. Subsequent to the sub-Tg enthalpy release, the glass undergoes a large jump in isobaric heat...... capacity (ΔCp) during glass transition, implying the fragile nature of the SA glass. The mullite starts to form before the end of glass transition, indicating that the SA glass is extremely unstable against crystallization. After the mullite formation, the remaining glass phase exhibits an increased Tg...... and a suppressed ΔCp. The formation of cristobalite at 1553 K indicates the dominance of silica in the remaining glass matrix. The cristobalite gradually re-melts as the isothermal heat-treatment temperature is raised from 1823 to 1853 K, which is well below the melting point of cristobalite, while the amount...

Glass sealing

Energy Technology Data Exchange (ETDEWEB)

Brow, R.K.; Kovacic, L.; Chambers, R.S. [Sandia National Labs., Albuquerque, NM (United States)

1996-04-01

Hernetic glass sealing technologies developed for weapons component applications can be utilized for the design and manufacture of fuel cells. Design and processing of of a seal are optimized through an integrated approach based on glass composition research, finite element analysis, and sealing process definition. Glass sealing procedures are selected to accommodate the limits imposed by glass composition and predicted calculations.

Medición de microdeformaciones en losas viales usando sensores de redes de Braggen fibras ópticas Microdeformation measurement of concrete roadway slabs using fiber Bragg gratings

Directory of Open Access Journals (Sweden)

Francisco Javier Vélez Hoyos

2010-06-01

Full Text Available En este trabajo se presenta un método no invasivo para la medición de microdeformaciones en estructuras de concreto usando sensores de redes de Bragg en fibras ópticas adheridos a su superficie. Se realizan mediciones en losas viales de concreto bajo una carga estática de 10 kN, encontrándose una relación aproximada de 2 : 1 entre la deformación registrada por los sensores y los valores arrojados por una simulación computacional con el método de elementos finitos. Se propone el uso de estos sensores para el monitoreo estructural de losas en una malla vial con sensores distribuidos y multiplexados por longitud de onda. Este es el primer reporte en Colombia de medición de deformación de losas viales usando sensores de fibra óptica.This work shows a non–invasive method for micro–deformation measurements of concrete structures using Bragg grating sensors in optical fibers adhered to the surface. Measurements on roadway slabs under a 10 kN static load are made, finding an approximated ratio of 2 : 1 between the deformation registered by the sensors and the values from a computational simulation with the finite element method. We propose the use of these sensors for slab structural monitoring in a road network employing distributed and wavelength multiplexed sensors. This is a first report in Colombia of roadway slabs microdeformation measurement using fiber optic sensors.

Analysis of early medieval glass beads - Glass in the transition period

Energy Technology Data Exchange (ETDEWEB)

Smit, Ziga, E-mail: ziga.smit@ijs.si [Faculty of Mathematics and Physics, University of Ljubljana, Jadranska 19, SI-1000 Ljubljana (Slovenia); Jozef Stefan Institute, Jamova 39, P.O.B. 3000, SI-1001 Ljubljana (Slovenia); Knific, Timotej [National Museum of Slovenia, Presernova 20, SI-1000 Ljubljana (Slovenia); Jezersek, David [Jozef Stefan Institute, Jamova 39, P.O.B. 3000, SI-1001 Ljubljana (Slovenia); Istenic, Janka [National Museum of Slovenia, Presernova 20, SI-1000 Ljubljana (Slovenia)

2012-05-01

Glass beads from graves excavated in Slovenia and dated archaeologically to the 7th-10th century AD were analysed by the combined PIXE-PIGE method. The results indicate two groups of glass; natron glass made in the Roman tradition and glass made with alkalis from the ash of halophytic plants, which gradually replaced natron glass after c. 800 AD. The alkalis used in the second group of glass seem to be in close relation to a variant of the Venetian white glass that appeared several centuries later. The origin of this glass may be traced to glass production in Mesopotamia and around the Aral Sea. All the mosaic beads with eye decoration, as well as most of the drawn-segmented and drawn-cut beads analysed, are of plant-ash glass, which confirms their supposed oriental origin.

Brine shrimp bioassay: importance of correct taxonomic identification of Artemia (Anostraca) species.

Science.gov (United States)

Ruebhart, David R; Cock, Ian E; Shaw, Glen R

2008-08-01

Despite the common use of the brine shrimp bioassay in toxicology, there is confusion in the literature regarding citation of the correct taxonomic identity of the Artemia species used. The genus Artemia, once thought to be represented by a single species Artemia salina, is now known to be composed of several bisexual species as well as parthenogenetic populations. Artemia franciscana is the best studied of the Artemia species and is considered to represent the vast majority of studies in which Artemia is used as an experimental test organism. We found that in studies referring to the use of A. salina, the zoogeography of the cyst harvest site indicated that the species used was actually A. franciscana. Those performing bioassays with Artemia need to exercise diligence in assigning correct species identification, as the identity of the test organism is an important parameter in assuring the validity of the results of the assay.

How to Identify Drug Paraphernalia

Science.gov (United States)

... paper bags Cigarette packages Electronic-cigarettes (also called E-cigarettes) Small glass vials Pill bottles Candy or gum ... clips (a metal holder for a marijuana cigarette) E-Cigarettes (to smoke marijuana concentrates) Heroin Small spoon Needles ...

The measurement of 222Rn in drinking water by low-level liquid scintillation counting

International Nuclear Information System (INIS)

Barnett, J.M.; McKlveen, J.W.

1992-01-01

Radon-222 (Rn) has universally been found in well water. Non-stagnant ground water is collected at the well head while the well is pumping. The water is adjusted to a slow, non-aerated, steady flow through a clear tube, and a 500 ml glass bottle is filled. The sample is tightly capped after a high meniscus has developed. In the laboratory, standard 22 ml glass vials are filled with 10 ml of a toluene based mineral oil LS cocktail. Then, two 5 ml sample aliquots are pipetted into the vial. Vials are capped tightly, shaken vigorously, and placed in the liquid scintillation (LS) counter. Secular equilibrium is established in approximately 4 hours, after which samples are counted for 100 minutes each. The counting efficiency for Rn and progeny ranges between 315 to 345 percent depending on the chosen spectral window. The average background is about 6 cpm. A total of 28 wells were tested for Rn in the Carefree-Cave Creek, Arizone, USA area. The area's geometric average Rn concentration was found to be 46.5 Bq*1 -1 . The associated estimated lung dose is 0.51 mSv*y -1 . (author) 8 refs.; 1 fig.; 1 tab

The ICRP working party on bioassay interpretation

International Nuclear Information System (INIS)

Fry, F.A.; Lipsztein, J.L.; Birchall, A.

2003-01-01

In recent years there have been many developments in modelling the behaviour of radionuclides in the human body. The current generation of models are designed to be more 'realistic' than the previous generation of simple compartment models. The International Commission on Radiological Protection (ICRP) uses these models to produce dose coefficients and recognises that there is a need to give more guidance on how these models can be used to interpret bioassay data. A working party has been set up to address the issue. This paper describes some of the problems, some approaches to solving the problems and the progress of the ICRP working party. (author)

Spherical 2+p spin-glass model: An exactly solvable model for glass to spin-glass transition

International Nuclear Information System (INIS)

Crisanti, A.; Leuzzi, L.

2004-01-01

We present the full phase diagram of the spherical 2+p spin-glass model with p≥4. The main outcome is the presence of a phase with both properties of full replica symmetry breaking phases of discrete models, e.g., the Sherrington-Kirkpatrick model, and those of one replica symmetry breaking. This phase has a finite complexity which leads to different dynamic and static properties. The phase diagram is rich enough to allow the study of different kinds of glass to spin glass and spin glass to spin glass phase transitions

Glass binder development for a glass-bonded sodalite ceramic waste form

International Nuclear Information System (INIS)

Riley, Brian J.; Vienna, John D.; Frank, Steven M.; Kroll, Jared O.; Peterson, Jacob A.

2017-01-01

This paper discusses work to develop Na_2O-B_2O_3-SiO_2 glass binders for immobilizing LiCl-KCl eutectic salt waste in a glass-bonded sodalite waste form following electrochemical reprocessing of used metallic nuclear fuel. In this paper, five new glasses with ~20 mass% Na_2O were designed to generate waste forms with high sodalite. The glasses were then used to produce ceramic waste forms with a surrogate salt waste. The waste forms made using these new glasses were formulated to generate more sodalite than those made with previous baseline glasses for this type of waste. The coefficients of thermal expansion for the glass phase in the glass-bonded sodalite waste forms made with the new binder glasses were closer to the sodalite phase in the critical temperature region near and below the glass transition temperature than previous binder glasses used. Finally, these improvements should result in lower probability of cracking in the full-scale monolithic ceramic waste form, leading to better long-term chemical durability.

Sediment toxicity assessment in the Lagoon of Venice (Italy) using Paracentrotus lividus (Echinodermata: Echinoidea) fertilization and embryo bioassays.

Science.gov (United States)

Volpi Ghirardini, A; Arizzi Novelli, A; Tagliapietra, D

2005-09-01

The capacity of two toxicity bioassays (fertilization and embryo toxicity tests) to discriminate sediment toxicity using the sea urchin Paracentrotus lividus was tested in five stations with different levels of pollution in the Lagoon of Venice. Two stations were located in estuarine sites, two in the industrial zone, and one in a site at the top of our quality gradient (reference). Elutriate was chosen as sediment matrix to assess the potential effects of bioavailable pollutants in the water column as a consequence of sediment resuspension (dredging and dumping, fishing gear, etc.). An experimental design based on Quality Assurance/Quality Control procedures (QA/QC) was adopted in order to set the methodological basis for an effective use of these bioassays in monitoring programs. Results revealed both higher embriotoxicity than spermiotoxicity in all stations and the efficacy of combined use of both toxicity bioassays in discriminating differing pollution/bioavailability between stations and periods. The good representativeness of the integrated sampling scheme and the standardization of all experimental phases yielded high precision of results. Clear Toxicity Fingerprints were evidenced for the investigated sites through the combined use of both bioassays. A good fit between ecotoxicological data and chemical contamination levels was found, except for unnatural sediment texture.

Using physical properties of molten glass to estimate glass composition

International Nuclear Information System (INIS)

Choi, Kwan Sik; Yang, Kyoung Hwa; Park, Jong Kil

1997-01-01

A vitrification process is under development in KEPRI for the treatment of low-and medium-level radioactive waste. Although the project is for developing and building Vitrification Pilot Plant in Korea, one of KEPRI's concerns is the quality control of the vitrified glass. This paper discusses a methodology for the estimation of glass composition by on-line measurement of molten glass properties, which could be applied to the plant for real-time quality control of the glass product. By remotely measuring viscosity and density of the molten glass, the glass characteristics such as composition can be estimated and eventually controlled. For this purpose, using the database of glass composition vs. physical properties in isothermal three-component system of SiO 2 -Na 2 O-B 2 O 3 , a software TERNARY has been developed which determines the glass composition by using two known physical properties (e.g. density and viscosity)

A new approach for bioassays based on frequency- and time-domain measurements of magnetic nanoparticles.

Science.gov (United States)

Oisjöen, Fredrik; Schneiderman, Justin F; Astalan, Andrea Prieto; Kalabukhov, Alexey; Johansson, Christer; Winkler, Dag

2010-01-15

We demonstrate a one-step wash-free bioassay measurement system capable of tracking biochemical binding events. Our approach combines the high resolution of frequency- and high speed of time-domain measurements in a single device in combination with a fast one-step bioassay. The one-step nature of our magnetic nanoparticle (MNP) based assay reduces the time between sample extraction and quantitative results while mitigating the risks of contamination related to washing steps. Our method also enables tracking of binding events, providing the possibility of, for example, investigation of how chemical/biological environments affect the rate of a binding process or study of the action of certain drugs. We detect specific biological binding events occurring on the surfaces of fluid-suspended MNPs that modify their magnetic relaxation behavior. Herein, we extrapolate a modest sensitivity to analyte of 100 ng/ml with the present setup using our rapid one-step bioassay. More importantly, we determine the size-distributions of the MNP systems with theoretical fits to our data obtained from the two complementary measurement modalities and demonstrate quantitative agreement between them. Copyright 2009 Elsevier B.V. All rights reserved.

Proyecto de mejora y acondicionamiento como apeadero multimodal de la parcela ARI-T03 y de varios viales en el municipio de San Fernando (Cádiz)

OpenAIRE

Díaz Ramos, Jesús

2014-01-01

El objeto del presente Proyecto es definir las obras necesarias para la correcta ejecución de las obras de mejora y acondicionamiento como apeadero multimodal de la parcela ARI-T03 y de varios viales, en el municipio de San Fernando (Cádiz).

Comparative performances of eggs and embryos of sea urchin (Paracentrotus lividus) in toxicity bioassays used for assessment of marine sediment quality.

Science.gov (United States)

Khosrovyan, A; Rodríguez-Romero, A; Salamanca, M J; Del Valls, T A; Riba, I; Serrano, F

2013-05-15

The potential toxicity of sediments from various ports was assessed by means of two different liquid-phase toxicity bioassays (acute and chronic) with embryos and eggs of sea urchin Paracentrotus lividus. Performances of embryos and eggs of P. lividus in these bioassays were compared for their interchangeable applicability in integrated sediment quality assessment. The obtained endpoints (percentages of normally developed plutei and fertilized eggs) were linked to physical and chemical properties of sediments and demonstrated dependence on sediment contamination. The endpoints in the two bioassays were strongly correlated and generally exhibited similar tendency throughout the samples. Therein, embryos demonstrated higher sensitivity to elutriate exposure, compared to eggs. It was concluded that these tests could be used interchangeably for testing toxicity of marine sediments. Preferential use of any of the bioassays can be determined by the discriminatory capacity of the test or vulnerability consideration of the test subject to the surrounding conditions. Copyright © 2013 Elsevier Ltd. All rights reserved.

Microstructuring of glasses

CERN Document Server

Hülsenberg, Dagmar; Bismarck, Alexander

2008-01-01

As microstructured glass becomes increasingly important for microsystems technology, the main application fields include micro-fluidic systems, micro-analysis systems, sensors, micro-actuators and implants. And, because glass has quite distinct properties from silicon, PMMA and metals, applications exist where only glass devices meet the requirements. The main advantages of glass derive from its amorphous nature, the precondition for its - theoretically - direction-independent geometric structurability. Microstructuring of Glasses deals with the amorphous state, various glass compositions and their properties, the interactions between glasses and the electromagnetic waves used to modify it. Also treated in detail are methods for influencing the geometrical microstructure of glasses by mechanical, chemical, thermal, optical, and electrical treatment, and the methods and equipment required to produce actual microdevices.

lead glass brick

CERN Multimedia

When you look through the glass at a picture behind, the picture appears raised up because light is slowed down in the dense glass. It is this density (4.06 gcm-3) that makes lead glass attractive to physicists. The refractive index of the glass is 1.708 at 400nm (violet light), meaning that light travels in the glass at about 58% its normal speed. At CERN, the OPAL detector uses some 12000 blocks of glass like this to measure particle energies.

Polycyclic aromatic hydrocarbons bioavailability in industrial and agricultural soils: Linking SPME and Tenax extraction with bioassays.

Science.gov (United States)

Guo, Meixia; Gong, Zongqiang; Li, Xiaojun; Allinson, Graeme; Rookes, James; Cahill, David

2017-06-01

The aims of this study were to evaluate the bioavailability of polycyclic aromatic hydrocarbons (PAHs) in industrial and agricultural soils using chemical methods and a bioassay, and to study the relationships between the methods. This was conducted by comparing the quantities of PAHs extracted from two manufactured gas plant (MGP) soils and an agricultural soil with low level contamination by solid-phase micro-extraction (SPME) and Tenax-TA extraction with the quantities taken up by the earthworm (Eisenia fetida). In addition, a biodegradation experiment was conducted on one MGP soil (MGP-A) to clarify the relationship between PAH removal by biodegradation and the variation in PAH concentrations in soil pore water. Results demonstrated that the earthworm bioassay could not be used to examine PAH bioavailability in the tested MGP soils; which was the case even in the diluted MGP-A soils after biodegradation. However, the bioassay was successfully applied to the agricultural soil. These results suggest that earthworms can only be used for bioassays in soils with low toxicity. In general, rapidly desorbing concentrations extracted by Tenax-TA could predict PAH concentrations accumulated in earthworms (R 2 =0.66), while SPME underestimated earthworm concentrations by a factor of 2.5. Both SPME and Tenax extraction can provide a useful tool to predict PAH bioavailability for earthworms, but Tenax-TA extraction was proven to be a more sensitive and precise method than SPME for the prediction of earthworm exposure in the agricultural soil. Copyright © 2017. Published by Elsevier Inc.

Estimation of uranium in bioassay samples of occupational workers by laser fluorimetry

International Nuclear Information System (INIS)

Suja, A.; Prabhu, S.P.; Sawant, P.D.; Sarkar, P.K.; Tiwari, A.K.; Sharma, R.

2012-01-01

A newly established uranium processing facility has been commissioned at BARC, Trombay. Monitoring of occupational workers is essential to assess intake of uranium in this facility. A group of 21 workers was selected for bioassay monitoring to assess the existing urinary excretion levels of uranium before the commencement of actual work. Bioassay samples collected from these workers were analyzed by ion-exchange technique followed by laser fluorimetry. Standard addition method was followed for estimation of uranium concentration in the samples. The minimum detectable activity by this technique is about 0.2 ng. The range of uranium observed in these samples varies from 19 to 132 ng/L. Few of these samples were also analyzed by fission track analysis technique and the results were found to be comparable to those obtained by laser fluorimetry. The urinary excretion rate observed for the individual can be regarded as a 'personal baseline' and will be treated as the existing level of uranium in urine for these workers at the facility. (author)

Comparative study of Graves' ophthalmopathy by ultrasonography, computed tomography, and fish bioassay

International Nuclear Information System (INIS)

Mann, K.; Schoener, W.; Juengst, D.; Karl, H.J.; Maier-Hauff, K.; Rothe, R.

1979-01-01

In 35 patients with Graves' ophthalmopathy (GO) thyroid function was tested by T 3 -RIA, T 4 -RIA, TBI, TRH-test, thyroid scanning, and determination of thyroid autoantibodies. Additional ultrasonography (A-scan), computed tomography (CT) of the orbit, and the determination of an exophthalmogenic serum activity in fish bioassay was performed. Typical alterations for GO were observed in 26 cases with ultrasonography. CT showed an enlargement of medial and/or lateral rectus muscles in 24 of 33 patients, and in 17 cases a region of high density in the apex of the muscle cone. The density of retrobulbar fat after i.v. injection of contrast medium did not differ significantly from that observed in normal men. Characteristic signs of GO were not detected in only 2 cases using both methods together. Exophthalmogenic serum activity was found in the IgG fraction of serum protein. The incidence rate was high (69%), but for diagnostic purpose the fish bioassay cannot be recommended. (orig.) 891 AJ/orig. 892 BRE [de

Storing of Extracts in Polypropylene Microcentrifuge Tubes Yields Contaminant Peak During Ultra-flow Liquid Chromatographic Analysis.

Science.gov (United States)

Kshirsagar, Parthraj R; Hegde, Harsha; Pai, Sandeep R

2016-05-01

This study was designed to understand the effect of storage in polypropylene microcentrifuge tubes and glass vials during ultra-flow liquid chromatographic (UFLC) analysis. One ml of methanol was placed in polypropylene microcentrifuge tubes (PP material, Autoclavable) and glass vials (Borosilicate) separately for 1, 2, 4, 8, 10, 20, 40, and 80 days intervals stored at -4°C. Contaminant peak was detected in methanol stored in polypropylene microcentrifuge tubes using UFLC analysis. The contaminant peak detected was prominent, sharp detectable at 9.176 ± 0.138 min on a Waters 250-4.6 mm, 4 μ, Nova-Pak C18 column with mobile phase consisting of methanol:water (70:30). It was evident from the study that long-term storage of biological samples prepared using methanol in polypropylene microcentrifuge tubes produce contaminant peak. Further, this may mislead in future reporting an unnatural compound by researchers. Long-term storage of biological samples prepared using methanol in polypropylene microcentrifuge tubes produce contaminant peakContamination peak with higher area under the curve (609993) was obtained in ultra-flow liquid chromatographic run for methanol stored in PP microcentrifuge tubesContamination peak was detected at retention time 9.113 min with a lambda max of 220.38 nm and 300 mAU intensity on the given chromatographic conditionsGlass vials serve better option over PP microcentrifuge tubes for storing biological samples. Abbreviations used: UFLC: Ultra Flow Liquid Chromatography; LC: Liquid Chromatography; MS: Mass spectrometry; AUC: Area Under Curve.

Contrasting the magnetic response between magnetic-glass and reentrant spin-glass

OpenAIRE

Roy, S. B.; Chattopadhyay, M. K.

2008-01-01

Magnetic-glass is a recently identified phenomenon in various classes of magnetic systems undergoing a first order magnetic phase transition. We shall highlight here a few experimentally determined characteristics of magnetic-glass and the relevant set of experiments, which will enable to distinguish a magnetic-glass unequivocally from the well known phenomena of spin-glass and reentrant spin-glass.

Analysis for drugs in saliva and breath

Science.gov (United States)

1981-09-25

Collection devices for saliva and breath that involved non-invasive techniques for sample collection were evaluated. Having subjects simply spit into a specially prepared glass vial was found to be an efficient, inexpensive and simple way to collect ...

Analysis for drug in saliva and breath

Science.gov (United States)

1981-09-25

Collection devices for saliva and breath that involved non-invasive : techniques for sample collection were evaluated. Having subjects simply : spit into a specially prepared glass vial was found to be an efficient, : inexpensive and simple way to co...

Magnetic-Field-Assisted Assembly of Ordered Multifunctional Ceramic Nanocomposites for Extreme Environments

Science.gov (United States)

2016-04-01

SUBJECT TERMS carbon nanotubes, composite, electromagnetic shielding , extreme environments, magnetism, fibers, woven composite, boron nitride...The samples were sealed in glass vial and exposed to the magnetic field immediately after deposition prior to crystallization of PEG that allowed

Comparison of a model vapor deposited glass films to equilibrium glass films

Science.gov (United States)

Flenner, Elijah; Berthier, Ludovic; Charbonneau, Patrick; Zamponi, Francesco

Vapor deposition of particles onto a substrate held at around 85% of the glass transition temperature can create glasses with increased density, enthalpy, kinetic stability, and mechanical stability compared to an ordinary glass created by cooling. It is estimated that an ordinary glass would need to age thousands of years to reach the kinetic stability of a vapor deposited glass, and a natural question is how close to the equilibrium is the vapor deposited glass. To understand the process, algorithms akin to vapor deposition are used to create simulated glasses that have a higher kinetic stability than their annealed counterpart, although these glasses may not be well equilibrated either. Here we use novel models optimized for a swap Monte Carlo algorithm in order to create equilibrium glass films and compare their properties with those of glasses obtained from vapor deposition algorithms. This approach allows us to directly assess the non-equilibrium nature of vapor-deposited ultrastable glasses. Simons Collaboration on Cracking the Glass Problem and NSF Grant No. DMR 1608086.

Effect-based trigger values for in vitro bioassays: Reading across from existing water quality guideline values.

Science.gov (United States)

Escher, Beate I; Neale, Peta A; Leusch, Frederic D L

2015-09-15

Cell-based bioassays are becoming increasingly popular in water quality assessment. The new generations of reporter-gene assays are very sensitive and effects are often detected in very clean water types such as drinking water and recycled water. For monitoring applications it is therefore imperative to derive trigger values that differentiate between acceptable and unacceptable effect levels. In this proof-of-concept paper, we propose a statistical method to read directly across from chemical guideline values to trigger values without the need to perform in vitro to in vivo extrapolations. The derivation is based on matching effect concentrations with existing chemical guideline values and filtering out appropriate chemicals that are responsive in the given bioassays at concentrations in the range of the guideline values. To account for the mixture effects of many chemicals acting together in a complex water sample, we propose bioanalytical equivalents that integrate the effects of groups of chemicals with the same mode of action that act in a concentration-additive manner. Statistical distribution methods are proposed to derive a specific effect-based trigger bioanalytical equivalent concentration (EBT-BEQ) for each bioassay of environmental interest that targets receptor-mediated toxicity. Even bioassays that are indicative of the same mode of action have slightly different numeric trigger values due to differences in their inherent sensitivity. The algorithm was applied to 18 cell-based bioassays and 11 provisional effect-based trigger bioanalytical equivalents were derived as an illustrative example using the 349 chemical guideline values protective for human health of the Australian Guidelines for Water Recycling. We illustrate the applicability using the example of a diverse set of water samples including recycled water. Most recycled water samples were compliant with the proposed triggers while wastewater effluent would not have been compliant with a few

Medición de microdeformaciones en losas viales usando sensores de redes de Bragg en fibras ópticas

OpenAIRE

Vélez-Hoyos, Francisco Javier; Serpa-Imbet, Claudia Milena; Gómez-Cardona, Nelson Darío

2010-01-01

En este trabajo se presenta un método no invasivo para la medición de microdeformaciones en estructuras de concreto usando sensores de redes de Bragg en fibras ópticas adheridos a su superficie. Se realizan mediciones en losas viales de concreto bajo una carga estática de 10 kN, encontrándose una relación aproximada de 2 : 1 entre la deformación registrada por los sensores y los valores arrojados por una simulación computacional con el método de elementos finitos. Se propone el uso de estos s...

Use of a modified microplate bioassay method to investigate antibacterial activity in the Peruvian medicinal plant Peperomia galioides.

Science.gov (United States)

Langfield, Richard D; Scarano, Frank J; Heitzman, Mary E; Kondo, Miwako; Hammond, Gerald B; Neto, Catherine C

2004-10-01

A versatile microplate bioassay for quick and sensitive determination of antibacterial activity was developed for use in screening medicinal plants and identification of their active principles. This assay can be used to determine minimum inhibitory concentrations for small quantities of organic or water-soluble plant extracts. Bioassay-guided fractionation of the stem and leaves of Peperomia galioides using this method found fractions containing grifolin and grifolic acid, which inhibited growth of Staphylococcus aureus and Staphylococcus epidermidis.

Comparative susceptibility of bemisia tabaci to imidacloprid in field- and laboratory-based bioassays

Science.gov (United States)

Bemisia tabaci biotype B is a resistance-prone pest of protected and open agriculture. Systemic uptake bioassays used in resistance monitoring programs have provided important information on susceptibility to neonicotinoid insecticides, but have remained decoupled from field performance. Simultaneou...

Diopside-Fluorapatite-Wollastonite Based Bioactive Glasses and Glass-ceramics =

Science.gov (United States)

Kansal, Ishu

Bioactive glasses and glass-ceramics are a class of biomaterials which elicit special response on their surface when in contact with biological fluids, leading to strong bonding to living tissue. This particular trait along with good sintering ability and high mechanical strength make them ideal materials for scaffold fabrication. The work presented in this thesis is directed towards understanding the composition-structure-property relationships in potentially bioactive glasses designed in CaO-MgO-P2O5-SiO2-F system, in some cases with added Na2O. The main emphasis has been on unearthing the influence of glass composition on molecular structure, sintering ability and bioactivity of phosphosilicate glasses. The parent glass compositions have been designed in the primary crystallization field of the pseudo-ternary system of diopside (CaO•MgO•2SiO2) - fluorapatite (9CaO•3P2O5•CaF2) - wollastonite (CaO•SiO2), followed by studying the impact of compositional variations on the structure-property relationships and sintering ability of these glasses. All the glasses investigated in this work have been synthesized via melt-quenching route and have been characterized for their molecular structure, sintering ability, chemical degradation and bioactivity using wide array of experimental tools and techniques. It has been shown that in all investigated glass compositions the silicate network was mainly dominated by Q2 units while phosphate in all the glasses was found to be coordinated in orthophosphate environment. The glass compositions designed in alkali-free region of diopside - fluorapatite system demonstrated excellent sintering ability and good bioactivity in order to qualify them as potential materials for scaffold fabrication while alkali-rich bioactive glasses not only hinder the densification during sintering but also induce cytotoxicity in vitro, thus, are not ideal candidates for in vitro tissue engineering. One of our bioglass compositions with low sodium

In situ bioassays with Chironomus riparius larvae to biomonitor metal pollution in rivers and to evaluate the efficiency of restoration measures in mine areas

Energy Technology Data Exchange (ETDEWEB)

Faria, Mafalda S. [CESAM and Departamento de Biologia da Universidade de Aveiro, Campus de Santiago, 3810-193 Aveiro (Portugal)], E-mail: mafaldafaria@sapo.pt; Lopes, Ricardo J. [CIBIO, Centro de Investigacao em Biodiversidade e Recursos Geneticos, Campus Agrario de Vairao, 4485-661 Vairao (Portugal); Malcato, Joao; Nogueira, Antonio J.A.; Soares, Amadeu M.V.M. [CESAM and Departamento de Biologia da Universidade de Aveiro, Campus de Santiago, 3810-193 Aveiro (Portugal)

2008-01-15

In this study we evaluate the ability of an in situ bioassay with Chironomus riparius larvae, using larval development and growth as endpoints, to biomonitor water quality and to assess the biological recovery of metal contaminated freshwater ecosystems of mine areas that are subject of restoration measures. The bioassay was carried out in streams located near an abandoned goldmine in North Portugal, throughout an environmental rehabilitation of the mine (2002-2004). During this period, a decrease in the inhibition of larval growth in the metal contaminated stream was observed. The bioassay was also performed in streams located near an active tungsten mine in Central Portugal. Larval growth and development were highly inhibited in the stream that receives acid drainage from the tungsten mine and treated water from the AMD treatment station. The results indicate that the bioassay can be used to evaluate the efficiency of environmental restoration measures in mining areas. - In situ bioassays with Chironomus riparius larvae can be a suitable tool to monitor restoration efficiency after a long time of metallic sediment contamination.

In situ bioassays with Chironomus riparius larvae to biomonitor metal pollution in rivers and to evaluate the efficiency of restoration measures in mine areas

International Nuclear Information System (INIS)

Faria, Mafalda S.; Lopes, Ricardo J.; Malcato, Joao; Nogueira, Antonio J.A.; Soares, Amadeu M.V.M.

2008-01-01

In this study we evaluate the ability of an in situ bioassay with Chironomus riparius larvae, using larval development and growth as endpoints, to biomonitor water quality and to assess the biological recovery of metal contaminated freshwater ecosystems of mine areas that are subject of restoration measures. The bioassay was carried out in streams located near an abandoned goldmine in North Portugal, throughout an environmental rehabilitation of the mine (2002-2004). During this period, a decrease in the inhibition of larval growth in the metal contaminated stream was observed. The bioassay was also performed in streams located near an active tungsten mine in Central Portugal. Larval growth and development were highly inhibited in the stream that receives acid drainage from the tungsten mine and treated water from the AMD treatment station. The results indicate that the bioassay can be used to evaluate the efficiency of environmental restoration measures in mining areas. - In situ bioassays with Chironomus riparius larvae can be a suitable tool to monitor restoration efficiency after a long time of metallic sediment contamination

Strategies for Transferring Mixtures of Organic Contaminants from Aquatic Environments into Bioassays

DEFF Research Database (Denmark)

Jahnke, Annika; Mayer, Philipp; Schäfer, Sabine

2016-01-01

and monitoring of such mixtures, a variety of cell-based in vitro and low-complexity in vivo bioassays based on algae, daphnids or fish embryos are available. A very important and sometimes unrecognized challenge is how to combine sampling, extraction and dosing to transfer the mixtures from the environment...

Development of a chick bioassay for determination of infectivity of viral pathogens in poultry litter.

Science.gov (United States)

Islam, A F M F; Walkden-Brown, S W; Groves, P J; Wells, B

2013-01-01

To develop a chicken bioassay to detect infective viral pathogens in poultry litter and to determine the effects of type of chicken and age of exposure, as well as the effect of simulated litter transportation, on the level of viral infectivity detected. A 5 × 2 × 2 factorial design, plus negative controls. Five chicken litters, including two with deliberate contamination (one transported and one not), two chicken types (specific-pathogen-free (SPF) Leghorns and Cobb broilers) and two ages at initial exposure (days 1 and 8). Two replicates of each treatment combination. The 10 chickens in each of 22 isolators were either exposed (20 isolators) or not (2 isolators) to 8 L of previously used or deliberately contaminated poultry litter in two deep scratch trays. At day 35 post-exposure, sera were assayed for antibodies against chicken anaemia virus (CAV), infectious bronchitis virus (IBV), infectious bursal disease virus (IBDV), Newcastle disease virus (NDV) and fowl adenovirus (FAV). Spleen samples were tested for Marek's disease virus (MDV) using real-time polymerase chain reaction. The bioassay detected CAV, IBDV and FAV, but not NDV, IBV or MDV, in chickens exposed to infected litters. Infection in SPF chickens was detected with greater sensitivity than in the broiler chickens. Sensitivity increased with age at exposure in broiler but not SPF chickens. Simulated transportation for 24 h had little effect on pathogen detection. A bioassay based on the exposure of day-old SPF chickens to poultry litter and measurement of seroconversion at day 35 post-exposure is a useful semi-quantitative assay for viral infectivity in poultry litter, with overnight transportation of litter having little effect on the level of viral infectivity detected. This bioassay has applications in research on litter treatment protocols. © 2013 The Authors. Australian Veterinary Journal © 2013 Australian Veterinary Association.

Aislamiento rápido del virus dengue 3 por el método de shell vial en el brote de dengue en Lima

Directory of Open Access Journals (Sweden)

Victoria Gutiérrez P

2005-07-01

Full Text Available El aislamiento de virus dengue con los métodos tradicionales demora hasta un mes, en situaciones de emergencia como el brote de dengue clásico en el distrito de Comas-Lima entre abril y mayo de 2005, es necesario un diagnóstico precoz. Se procesaron 117 muestras de sueros de pacientes con diagnóstico clínico de dengue clásico en fase virémica procedentes la zona del brote, mediante el método de shell vial para el aislamiento del virus dengue en la línea celular C6-36, se identificó el serotipo del virus mediante inmunofluorescencia indirecta (IFI empleando anticuerpos monoclonales. Se logró el aislamiento del virus DEN-3 al quinto día de cosecha en el 48,7% (57/117 de los sueros. Los resultados sugieren que el método de shell vial, por el menor tiempo de aislamiento que el método tradicional, puede ser implementado como método de diagnóstico y usado en la vigilancia epidemiológica del virus dengue.

Fluorescence lifetime based bioassays

Science.gov (United States)

Meyer-Almes, Franz-Josef

2017-12-01

Fluorescence lifetime (FLT) is a robust intrinsic property and material constant of fluorescent matter. Measuring this important physical indicator has evolved from a laboratory curiosity to a powerful and established technique for a variety of applications in drug discovery, medical diagnostics and basic biological research. This distinct trend was mainly driven by improved and meanwhile affordable laser and detection instrumentation on the one hand, and the development of suitable FLT probes and biological assays on the other. In this process two essential working approaches emerged. The first one is primarily focused on high throughput applications employing biochemical in vitro assays with no requirement for high spatial resolution. The second even more dynamic trend is the significant expansion of assay methods combining highly time and spatially resolved fluorescence data by fluorescence lifetime imaging. The latter approach is currently pursued to enable not only the investigation of immortal tumor cell lines, but also specific tissues or even organs in living animals. This review tries to give an actual overview about the current status of FLT based bioassays and the wide range of application opportunities in biomedical and life science areas. In addition, future trends of FLT technologies will be discussed.

Ecotoxicological assessment of metal-polluted urban soils using bioassays with three soil invertebrates.

NARCIS (Netherlands)

Santarufo, L.; van Gestel, C.A.M.; Maisto, G.

2012-01-01

This study aimed at assessing the quality of urban soils by integrating chemical and ecotoxicological approaches. Soils from five sites in downtown Naples, Italy, were sampled and characterized for physical-chemical properties and total and water-extractable metal concentrations. Bioassays with

Leaching of glass

International Nuclear Information System (INIS)

Hench, L.L.

1977-01-01

Understanding surface compositional profiles of glasses over a range of 0-2000 A with a variety of analytical instruments shows that five general types of glass surfaces exist. The surface character of a glass article depends upon bulk composition and environmental history during which surface dealkalization, film formation, and network dissolution can occur. Environmental-surface interactions generally result in complex compositional profiles of all the constituents in a glass. Durable glasses almost always develop a stable surface film which has a higher concentration of network formers than the bulk composition. Compositional effects that are used to improve glass durability usually improve the stability of the surface films. Durability tests or service conditions that lead to film destruction are especially severe for the most silicate glasses. 43 references

Nonane as a radiolytic product in irradiated bacon

International Nuclear Information System (INIS)

Singh, H.; Guerrero, A.; Kremers, W.

1993-01-01

Formation of nonane in irradiated bacon has been confirmed by gas chromatographic/mass spectrometric (GC/MS) analysis of irradiated nitrogen-flushed homogenized bacon in scaled glass vials. Unirradiated bacon did not show the presence of nonane under similar conditions

Proof of concept for a novel insecticide bioassay based on sugar feeding by adult Aedes aegypti (Stegomyia aegypti).

Science.gov (United States)

Stell, F M; Roe, R M; Arellano, C; Kennedy, L; Thornton, H; Saavedra-Rodriguez, K; Wesson, D M; Black, W C; Apperson, C S

2013-09-01

Aedes aegypti L. (Stegomyia aegypti) (Diptera: Culicidae) is the principal vector of dengue and yellow fever viruses in tropical and subtropical regions of the world. Disease management is largely based on mosquito control achieved by insecticides applied to interior resting surfaces and through space sprays. Population monitoring to detect insecticide resistance is a significant component of integrated disease management programmes. We developed a bioassay method for assessing insecticide susceptibility based on the feeding activity of mosquitoes on plant sugars. Our prototype sugar-insecticide feeding bioassay system was composed of inexpensive, disposable components, contained minimal volumes of insecticide, and was compact and highly transportable. Individual mosquitoes were assayed in a plastic cup that contained a sucrose-permethrin solution. Trypan blue dye was added to create a visual marker in the mosquito's abdomen for ingested sucrose-permethrin solution. Blue faecal spots provided further evidence of solution ingestion. With the sugar-insecticide feeding bioassay, the permethrin susceptibility of Ae. aegypti females from two field-collected strains was characterized by probit analysis of dosage-response data. The field strains were also tested by forced contact of females with permethrin residues on filter paper. Dosage-response patterns were similar, indicating that the sugar-insecticide feeding bioassay had appropriately characterized the permethrin susceptibility of the two strains. © 2012 The Royal Entomological Society.

Stability assessment of lyophilized intravenous immunoglobulin after reconstitution in glass containers and poly(vinyl chloride) bags.

Science.gov (United States)

Parti, R; Mankarious, S

1997-02-01

Human intravenous immunoglobulin (IGIV) has been in use for the past 20 years. This biological product is commonly provided in liquid or lyophilized dosage form. When the lyophilized product is rehydrated, it is usually administered within 2-3 h from time of complete dissolution. While this practice is advisable whenever possible, occasionally the patient or care-giver may need to delay the infusion. Hence, a study of the stability of lyophilized IGIV after reconstitution with water for injection was conducted. The reconstituted product was stored either in its original glass container or pooled into poly(vinyl chloride) (PVC) bags. The effect of extended storage on the active ingredient (IgG), excipients (glucose, albumin) and extractables [sodium from glass vials, and di-(2-ethyl-hexyl) phthalate and cyclohexanone from PVC bags] was evaluated. The stability of the active ingredient was evaluated by physico-chemical tests (molecularsize distribution, pH, appearance, total protein), monitoring titres of a specific antibody (hepatitis B surface antigen) and an antibody functional test (bacterial opsonization). To evaluate the risk of microbial contamination during reconstitution and pooling procedures, sterility, pyrogen and animal-safety tests were included in the protocol. The potential of IgG polymerizing in solution during storage and subsequent complement activation was evaluated by assaying for non-specific binding of complement (anti-complement activity). Results show that aseptically reconstituted IGIV is stable and remains sterile up to 48 h at 5 degrees C. The reconstituted product was also found to be stable at room temperature (25 degrees C) up to 12 h.

Colloidal glasses

Indian Academy of Sciences (India)

First page Back Continue Last page Overview Graphics. Colloidal glasses. Glassy state is attained when system fails to reach equilibrium due to crowding of constituent particles. In molecular glasses, glassy state is reached by rapidly lowering the temperature. In colloidal glasses, glassy state is reached by increasing the ...

Analytical procedure for the in-vial derivatization-extraction of phenolic acids and flavonoids in methanolic and aqueous plant extracts followed by gas chromatography with mass selective detection.

NARCIS (Netherlands)

Fiamegos, Y.C.; Nanos, C.G.; Vervoort, J.J.M.; Stalikas, C.D.

2004-01-01

An in-vial simple method for the combined derivatization and extraction of phenolic acids and flavonoids from plant extracts and their direct determination with GC-MS, is described. The method is taking advantage of the beneficial potentials of phase transfer catalysis (PTC). Catalysts in soluble

A Choline Oxidase Amperometric Bioassay for the Detection of Mustard Agents Based on Screen-Printed Electrodes Modified with Prussian Blue Nanoparticles

Directory of Open Access Journals (Sweden)

Fabiana Arduini

2015-02-01

Full Text Available In this work a novel bioassay for mustard agent detection was proposed. The bioassay is based on the capability of these compounds to inhibit the enzyme choline oxidase. The enzymatic activity, which is correlated to the mustard agents, was electrochemically monitored measuring the enzymatic product, hydrogen peroxide, by means of a screen-printed electrode modified with Prussian Blue nanoparticles. Prussian Blue nanoparticles are able to electrocatalyse the hydrogen peroxide concentration reduction at low applied potential (−50 mV vs. Ag/AgCl, thus allowing the detection of the mustard agents with no electrochemical interferences. The suitability of this novel bioassay was tested with the nitrogen mustard simulant bis(2-chloroethylamine and the sulfur mustard simulants 2-chloroethyl ethyl sulfide and 2-chloroethyl phenyl sulfide. The bioassay proposed in this work allowed the detection of mustard agent simulants with good sensitivity and fast response, which are excellent premises for the development of a miniaturised sensor well suited for an alarm system in case of terrorist attacks.

Heating-induced glass-glass and glass-liquid transformations in computer simulations of water

Science.gov (United States)

Chiu, Janet; Starr, Francis W.; Giovambattista, Nicolas

2014-03-01

Water exists in at least two families of glassy states, broadly categorized as the low-density (LDA) and high-density amorphous ice (HDA). Remarkably, LDA and HDA can be reversibly interconverted via appropriate thermodynamic paths, such as isothermal compression and isobaric heating, exhibiting first-order-like phase transitions. We perform out-of-equilibrium molecular dynamics simulations of glassy water using the ST2 model to study the evolution of LDA and HDA upon isobaric heating. Depending on pressure, glass-to-glass, glass-to-crystal, glass-to-vapor, as well as glass-to-liquid transformations are found. Specifically, heating LDA results in the following transformations, with increasing heating pressures: (i) LDA-to-vapor (sublimation), (ii) LDA-to-liquid (glass transition), (iii) LDA-to-HDA-to-liquid, (iv) LDA-to-HDA-to-liquid-to-crystal, and (v) LDA-to-HDA-to-crystal. Similarly, heating HDA results in the following transformations, with decreasing heating pressures: (a) HDA-to-crystal, (b) HDA-to-liquid-to-crystal, (c) HDA-to-liquid (glass transition), (d) HDA-to-LDA-to-liquid, and (e) HDA-to-LDA-to-vapor. A more complex sequence may be possible using lower heating rates. For each of these transformations, we determine the corresponding transformation temperature as function of pressure, and provide a P-T "phase diagram" for glassy water based on isobaric heating. Our results for isobaric heating dovetail with the LDA-HDA transformations reported for ST2 glassy water based on isothermal compression/decompression processes [Chiu et al., J. Chem. Phys. 139, 184504 (2013)]. The resulting phase diagram is consistent with the liquid-liquid phase transition hypothesis. At the same time, the glass phase diagram is sensitive to sample preparation, such as heating or compression rates. Interestingly, at least for the rates explored, our results suggest that the LDA-to-liquid (HDA-to-liquid) and LDA-to-HDA (HDA-to-LDA) transformation lines on heating are related

Heating-induced glass-glass and glass-liquid transformations in computer simulations of water

International Nuclear Information System (INIS)

Chiu, Janet; Giovambattista, Nicolas; Starr, Francis W.

2014-01-01

Water exists in at least two families of glassy states, broadly categorized as the low-density (LDA) and high-density amorphous ice (HDA). Remarkably, LDA and HDA can be reversibly interconverted via appropriate thermodynamic paths, such as isothermal compression and isobaric heating, exhibiting first-order-like phase transitions. We perform out-of-equilibrium molecular dynamics simulations of glassy water using the ST2 model to study the evolution of LDA and HDA upon isobaric heating. Depending on pressure, glass-to-glass, glass-to-crystal, glass-to-vapor, as well as glass-to-liquid transformations are found. Specifically, heating LDA results in the following transformations, with increasing heating pressures: (i) LDA-to-vapor (sublimation), (ii) LDA-to-liquid (glass transition), (iii) LDA-to-HDA-to-liquid, (iv) LDA-to-HDA-to-liquid-to-crystal, and (v) LDA-to-HDA-to-crystal. Similarly, heating HDA results in the following transformations, with decreasing heating pressures: (a) HDA-to-crystal, (b) HDA-to-liquid-to-crystal, (c) HDA-to-liquid (glass transition), (d) HDA-to-LDA-to-liquid, and (e) HDA-to-LDA-to-vapor. A more complex sequence may be possible using lower heating rates. For each of these transformations, we determine the corresponding transformation temperature as function of pressure, and provide a P-T “phase diagram” for glassy water based on isobaric heating. Our results for isobaric heating dovetail with the LDA-HDA transformations reported for ST2 glassy water based on isothermal compression/decompression processes [Chiu et al., J. Chem. Phys. 139, 184504 (2013)]. The resulting phase diagram is consistent with the liquid-liquid phase transition hypothesis. At the same time, the glass phase diagram is sensitive to sample preparation, such as heating or compression rates. Interestingly, at least for the rates explored, our results suggest that the LDA-to-liquid (HDA-to-liquid) and LDA-to-HDA (HDA-to-LDA) transformation lines on heating are related

Heating-induced glass-glass and glass-liquid transformations in computer simulations of water

Energy Technology Data Exchange (ETDEWEB)

Chiu, Janet; Giovambattista, Nicolas [Department of Physics, Brooklyn College of the City University of New York, Brooklyn, New York 11210 (United States); Starr, Francis W. [Department of Physics, Wesleyan University, Middletown, Connecticut 06459 (United States)

2014-03-21

Water exists in at least two families of glassy states, broadly categorized as the low-density (LDA) and high-density amorphous ice (HDA). Remarkably, LDA and HDA can be reversibly interconverted via appropriate thermodynamic paths, such as isothermal compression and isobaric heating, exhibiting first-order-like phase transitions. We perform out-of-equilibrium molecular dynamics simulations of glassy water using the ST2 model to study the evolution of LDA and HDA upon isobaric heating. Depending on pressure, glass-to-glass, glass-to-crystal, glass-to-vapor, as well as glass-to-liquid transformations are found. Specifically, heating LDA results in the following transformations, with increasing heating pressures: (i) LDA-to-vapor (sublimation), (ii) LDA-to-liquid (glass transition), (iii) LDA-to-HDA-to-liquid, (iv) LDA-to-HDA-to-liquid-to-crystal, and (v) LDA-to-HDA-to-crystal. Similarly, heating HDA results in the following transformations, with decreasing heating pressures: (a) HDA-to-crystal, (b) HDA-to-liquid-to-crystal, (c) HDA-to-liquid (glass transition), (d) HDA-to-LDA-to-liquid, and (e) HDA-to-LDA-to-vapor. A more complex sequence may be possible using lower heating rates. For each of these transformations, we determine the corresponding transformation temperature as function of pressure, and provide a P-T “phase diagram” for glassy water based on isobaric heating. Our results for isobaric heating dovetail with the LDA-HDA transformations reported for ST2 glassy water based on isothermal compression/decompression processes [Chiu et al., J. Chem. Phys. 139, 184504 (2013)]. The resulting phase diagram is consistent with the liquid-liquid phase transition hypothesis. At the same time, the glass phase diagram is sensitive to sample preparation, such as heating or compression rates. Interestingly, at least for the rates explored, our results suggest that the LDA-to-liquid (HDA-to-liquid) and LDA-to-HDA (HDA-to-LDA) transformation lines on heating are related

Database and Interim Glass Property Models for Hanford HLW Glasses

International Nuclear Information System (INIS)

Hrma, Pavel R; Piepel, Gregory F; Vienna, John D; Cooley, Scott K; Kim, Dong-Sang; Russell, Renee L

2001-01-01

The purpose of this report is to provide a methodology for an increase in the efficiency and a decrease in the cost of vitrifying high-level waste (HLW) by optimizing HLW glass formulation. This methodology consists in collecting and generating a database of glass properties that determine HLW glass processability and acceptability and relating these properties to glass composition. The report explains how the property-composition models are developed, fitted to data, used for glass formulation optimization, and continuously updated in response to changes in HLW composition estimates and changes in glass processing technology. Further, the report reviews the glass property-composition literature data and presents their preliminary critical evaluation and screening. Finally the report provides interim property-composition models for melt viscosity, for liquidus temperature (with spinel and zircon primary crystalline phases), and for the product consistency test normalized releases of B, Na, and Li. Models were fitted to a subset of the screened database deemed most relevant for the current HLW composition region

High-throughput tri-colour flow cytometry technique to assess Plasmodium falciparum parasitaemia in bioassays

DEFF Research Database (Denmark)

Tiendrebeogo, Regis W; Adu, Bright; Singh, Susheel K

2014-01-01

BACKGROUND: Unbiased flow cytometry-based methods have become the technique of choice in many laboratories for high-throughput, accurate assessments of malaria parasites in bioassays. A method to quantify live parasites based on mitotracker red CMXRos was recently described but consistent...... distinction of early ring stages of Plasmodium falciparum from uninfected red blood cells (uRBC) remains a challenge. METHODS: Here, a high-throughput, three-parameter (tri-colour) flow cytometry technique based on mitotracker red dye, the nucleic acid dye coriphosphine O (CPO) and the leucocyte marker CD45...... for enumerating live parasites in bioassays was developed. The technique was applied to estimate the specific growth inhibition index (SGI) in the antibody-dependent cellular inhibition (ADCI) assay and compared to parasite quantification by microscopy and mitotracker red staining. The Bland-Altman analysis...

Bioassay using the water soluble fraction of a Nigerian Light Crude ...

African Journals Online (AJOL)

Summary: A 96-hour bioassay was conducted using the water soluble fraction of a Nigerian light crude oil sample on Clarias gariepinus fingerlings. 0, 2.5, 5.0, 7.5 and 10 mls of water soluble fractions (WSF) of the oil were added to 1000 litres of de-chlorinated tap water to form 0, 25, 50 , 75 and 100 parts per million ...

Comparison of mouse and swine bioassays for determination of soil arsenic relative bioavailability

Science.gov (United States)

Evaluation of soil arsenic (As) relative bioavailability (RBA) is essential to accurately assess human exposure to As contaminated soils via the incidental ingestion pathway. A variety of animal bioassays have been developed to estimate As RBA in contaminated soils and dusts, wit...

Neutron- and light-scattering studies of the liquid-to-glass and glass-to-glass transitions in dense copolymer micellar solutions

International Nuclear Information System (INIS)

Chen Weiren; Chen Sowhsin; Mallamace, Francesco; Glinka, Charles J.; Fratini, Emiliano

2003-01-01

Recent mode coupling theory (MCT) calculations show that if a short-range attractive interaction is added to the pure hard sphere system, one may observe a new type of glass originating from the clustering effect (the attractive glass) as a result of the attractive interaction. This is in addition to the known glass-forming mechanism due to the cage effect in the hard sphere system (the repulsive glass). The calculations also indicate that if the range of attraction is sufficiently short compared to the diameter of the particle, within a certain interval of volume fractions where the two glass-forming mechanisms nearly balance each other, varying the external control parameter, the effective temperature, makes the glass-to-liquid-to-glass reentrance and the glass-to-glass transitions possible. Here we present experimental evidence of both transitions, obtained from small-angle neutron-scattering and photon correlation measurements taken from dense L64 copolymer micellar solutions in heavy water. Varying the temperature in certain predicted volume fraction range triggers a sharp transition between these two different types of glass. In particular, according to MCT, there is an end point (called A 3 singularity) of this glass-to-glass transition line, beyond which the long-time dynamics of the two glasses become identical. Our findings confirm this theoretical prediction. Surprisingly, although the Debye-Waller factors, the long-time limit of the coherent intermediate scattering functions, of these two glasses obtained from photon correlation measurements indeed become identical at the predicted volume fraction, they exhibit distinctly different intermediate time relaxation. Furthermore, our experimental results obtained from volume fractions beyond the end point are characterized by the same features as the repulsive glass obtained before the end point. A complete phase diagram giving the boundaries of the structural arrest transitions for L64 micellar system is

Detection of estrogen receptor endocrine disruptor potency of commonly used organochlorine pesticides using the LUMI-CELL ER bioassay

Energy Technology Data Exchange (ETDEWEB)

Gordon, J D; Chu, A C; Clark, G C [Xenobiotic Detection Systems, Inc., Durham, NC (United States); Chu, M D [Alta Analytical Perspectives, Wilmington, NC (United States); Denison, M S [Dept. of Environmental Toxicology, Univ. of California, Davis, CA (United States)

2004-09-15

In order to detect the endocrine disrupting potency of organochlorine pesticides and other compounds, BG-1 (human ovarian carcinoma) cells containing a stably transfected estrogenresponsive luciferase reporter gene plasmid (BG1Luc4E2), was used. This cell line, termed the LUMI-CELL trademark ER estrogenic cell bioassay system, responds in a time-, dose dependent- and chemical-specific manner with the induction of luciferase gene expression in response to exposure to estrogen (but not other steroid hormones) and estrogenic chemicals in a high-throughput screening (HTPS) format6. Here we describe studies in which the LUMI-CELL trademark ER estrogenic cell bioassay system was used for high throughput screening (HTPS) analysis of the estrogenic disrupting potency of several commonly used pesticides and organochlorines: p,p'DDT; p,p'-DDE; DDD; {alpha}a-chlordane; {psi}-chlordane; Kepone; Methoxychlor; Vinclozolin; Fenarimol; 2,4,5-Trichlorophenoxyacetic Acid; and Dieldrin. Our results demonstrate the utility of XDS's LUMI-CELL trademark ER bioassay HTPS system for screening chemicals for estrogenic activity.

Field and Bioassay Indicators for Internal Dose Intervention Therapy

International Nuclear Information System (INIS)

Carbaugh, Eugene H.

2007-01-01

Guidance is presented that is used at the U.S. Department of Energy Hanford Site to identify the potential need for medical intervention in response to intakes of radioactivity. The guidance, based on ICRP Publication 30 models and committed effective dose equivalents of 20 mSv and 200 mSv, is expressed as numerical workplace measurements and derived first-day bioassay results for large intakes. It is used by facility radiation protection staff and on-call dosimetry support staff during the first few days following an intake

Aqueous corrosion of silicate glasses. Analogy between volcanic glasses and the French nuclear waste glass R7T7

International Nuclear Information System (INIS)

Goldschmidt, F.

1991-01-01

The behaviour of borosilicate glasses upon aqueous corrosion is controlled for long periods of time (>10,000 years) by processes which are not directly accessible by means of laboratory experiments. The analogical approach consists here to compare leaching performances between the french nuclear waste glass R7T7 and natural volcanic glasses, basaltic and rhyolitic ones. The three glasses were leached in the same conditions; open system, 90 deg C, initial pH of 9.7. Basaltic and R7T7 glasses having the same kinetic of dissolution, the basaltic glass was chosen as the best analogue. (author). refs., figs., tabs

Biomarkers and bioassays as alternative screening methods for the presence and effects of PCDD, PCDF and PCB

International Nuclear Information System (INIS)

Bosveld, A.T.C.B.; Berg, M.V.

1994-01-01

Polyhalogenated aromatic hydrocarbons (PHAH) are wide spread, highly toxic, environmental contaminants. As such they pose risks for both humans and wildlife. For risk assessment purposes, concentrations are generally analyzed by HRGC-HR/LRMS. With the analytical data, mixture toxicity is calculated using the TEF concept. With this method only the defined congeners are taken into account and additivity for all congeners is assumed, whereas synergistic and antagonistic effects for several PCDD/F in combination with PCB have also been reported. To avoid these problems and high analytical costs, bioassays can be used for screening purposes. Cytochrome P 450 1 A 1 induction and vitamin A and thyroid hormone levels are shown to be useful markers for PHAH exposure. When bioassays based on cytochrome P 450 1 A 1 induction, in cultured cells, in multi-well culturing plates, are used, 2,3,7,8-TCDD detection limits <0.2 pg are possible. As such these bioassays are highly sensitive, cost effective and time saving. This application can be used as a pre-screening method to determine total ''dioxin'' content of environmental samples. (orig.)

Log bioassay of residual effectiveness of insecticides against bark beetles

Science.gov (United States)

Richard H. Smith

1982-01-01

Residual effectiveness of nine insecticides applied to bark was tested against western, mountain, and Jeffrey pine beetles. Ponderosa and Jeffrey pine trees were treated and logs cut from them 2 to 13 months later, and bioassayed with the three beetles. The insecticides were sprayed at the rate of 1 gal (3.8 l) per 40- or 80-ft² (3.6 or 7.2 m²) bark surface at varying...

Spheroidization of glass powders for glass ionomer cements.

Science.gov (United States)

Gu, Y W; Yap, A U J; Cheang, P; Kumar, R

2004-08-01

Commercial angular glass powders were spheroidized using both the flame spraying and inductively coupled radio frequency plasma spraying techniques. Spherical powders with different particle size distributions were obtained after spheroidization. The effects of spherical glass powders on the mechanical properties of glass ionomer cements (GICs) were investigated. Results showed that the particle size distribution of the glass powders had a significant influence on the mechanical properties of GICs. Powders with a bimodal particle size distribution ensured a high packing density of glass ionomer cements, giving relatively high mechanical properties of GICs. GICs prepared by flame-spheroidized powders showed low strength values due to the loss of fine particles during flame spraying, leading to a low packing density and few metal ions reacting with polyacrylic acid to form cross-linking. GICs prepared by the nano-sized powders showed low strength because of the low bulk density of the nano-sized powders and hence low powder/liquid ratio of GICs.

Diseño de un plan estratégico de seguridad vial departamental (Modelo piloto para el departamento de Boyacá

Directory of Open Access Journals (Sweden)

Flor Ángela Cerquera Escobar Julio Andrés Pabón Cachope Ricardo Andrés Fajardo

2010-11-01

Full Text Available Sintetiza  una  serie  de  consideraciones  que  sirvencomo marco  de  referencia  para  definir  un  plan  deacción en seguridad vial, cuyo desarrollo y ejecuciónestán  encaminados  a  reducir  los  accidentes  en  lasvías del departamento de Boyacá, y que sirve comomodelo guía para cualquier otra región del país. Losresultados  que  se  presentan  fueron  obtenidos  en  eldesarrollo  del  proyecto  de  grado  en  Ingeniería  deTransporte  y  Vías  t itulado  “Diseño  del  PlanEstratégico de Seguridad Vial para el departamentode Boyacá”;  además,  se  consideran  varios  tópicosplanteados en documentos que sobre Seguridad Vialha  desarrollado  el  Grupo  de  Invest igación  yDesarrollo en Operación del Tránsito, GIDOT. Esteproyecto  se  adelantó  como  un  direccionamiento  alPlan  de  Desarrollo  del  departamento,   en  lo

GLASS COMPOSITION-TCLP RESPONSE MODEL FOR WASTE GLASSES

International Nuclear Information System (INIS)

Kim, Dong-Sang; Vienna, John D.

2004-01-01

A first-order property model for normalized Toxicity Characteristic Leaching Procedure (TCLP) release as a function of glass composition was developed using data collected from various studies. The normalized boron release is used to estimate the release of toxic elements based on the observation that the boron release represents the conservative release for those constituents of interest. The current TCLP model has two targeted application areas: (1) delisting of waste-glass product as radioactive (not mixed) waste and (2) designating the glass wastes generated from waste-glass research activities as hazardous or non-hazardous. This paper describes the data collection and model development for TCLP releases and discusses the issues related to the application of the model

Bioassays for Evaluating Water Quality: Screening for total bioactivity to assess water safety

Science.gov (United States)

Bioassays are a potential solution for assessing complex samples since they screen for total bioactivity for a given pathway or mode of action (MOA), such as estrogen receptor activation, in the samples. Overall, they can account for the three challenges listed above, and can sim...

Multiple Glass Ceilings

OpenAIRE

Russo, Giovanni; Hassink, Wolter

2011-01-01

Both vertical (between job levels) and horizontal (within job levels) mobility can be sources of wage growth. We find that the glass ceiling operates at both margins. The unexplained part of the wage gap grows across job levels (glass ceiling at the vertical margin) and across the deciles of the intra-job-level wage distribution (glass ceiling at the horizontal margin). This implies that women face many glass ceilings, one for each job level above the second, and that the glass ceiling is a p...

Thermal properties and crystallization of lithium–mica glass and glass-ceramics

International Nuclear Information System (INIS)

Nia, A. Faeghi

2013-01-01

Highlights: • Two groups of Li–mica glass-ceramics, have been compared. • By controlling the glass composition, crystalline lepidolite was obtained. • The T p of Li–mica was through the previous virgilite and eucryptite phase. - Abstract: The purpose of this study was the synthesis of two groups of Li–mica glass-ceramics denoted by lepidolite (Al 2.5 F 2 KLi 1.5 O 10 Si 3 ) and Li-phlogopite (LiMg 3 AlSi 3 O 10 F 2 ). The studied system was SiO 2 –Al 2 O 3 –MgO–K 2 O–Li 2 O. A total of 3 compositions were prepared. Bulk casted glasses and sintered glass-ceramics of Li-phlogopite and lepidolite systems, were prepared. Eucryptite and virgilite were two prior phases of lepidolite and Li-phlogopite crystallization. It was shown that the obtained glass-ceramics have lower TEC than corresponding glasses. Sinterability of lepidolite glass-ceramic was shown that improved by increasing the Al 2 O 3 content in glass composition. TEC and microhardness values were α = 6.08 × 10 −6 /°C, 755 ± 11.1, α = 7.86 × 10 −6 /°C, 739 ± 7.4 and α = 5.05 × 10 −6 /°C, 658 ± 6.2 HV for Li-lep, Klep1 and Klep2 glasses, respectively

Crystallization In Multicomponent Glasses

International Nuclear Information System (INIS)

Kruger, A.A.; Hrma, P.R.

2009-01-01

In glass processing situations involving glass crystallization, various crystalline forms nucleate, grow, and dissolve, typically in a nonuniform temperature field of molten glass subjected to convection. Nuclear waste glasses are remarkable examples of multicomponent vitrified mixtures involving partial crystallization. In the glass melter, crystals form and dissolve during batch-to-glass conversion, melter processing, and product cooling. Crystals often agglomerate and sink, and they may settle at the melter bottom. Within the body of cooling glass, multiple phases crystallize in a non-uniform time-dependent temperature field. Self-organizing periodic distribution (the Liesegnang effect) is common. Various crystallization phenomena that occur in glass making are reviewed.

CRYSTALLIZATION IN MULTICOMPONENT GLASSES

Energy Technology Data Exchange (ETDEWEB)

KRUGER AA; HRMA PR

2009-10-08

In glass processing situations involving glass crystallization, various crystalline forms nucleate, grow, and dissolve, typically in a nonuniform temperature field of molten glass subjected to convection. Nuclear waste glasses are remarkable examples of multicomponent vitrified mixtures involving partial crystallization. In the glass melter, crystals form and dissolve during batch-to-glass conversion, melter processing, and product cooling. Crystals often agglomerate and sink, and they may settle at the melter bottom. Within the body of cooling glass, multiple phases crystallize in a non-uniform time-dependent temperature field. Self-organizing periodic distribution (the Liesegnang effect) is common. Various crystallization phenomena that occur in glass making are reviewed.

Volumetric change of simulated radioactive waste glass irradiated by electron accelerator. [Silica glass

Energy Technology Data Exchange (ETDEWEB)

Sato, Seichi; Furuya, Hirotaka; Inagaki, Yaohiro; Kozaka, Tetsuo; Sugisaki, Masayasu

1987-11-01

Density changes of simulated radioactive waste glasses, silica glass and Pyrex glass irradiated by an electron accelerator were measured by a ''sink-float'' technique. The density changes of the waste and silica glasses were less than 0.05 %, irradiated at 2.0 MeV up to the fluence of 1.7 x 10/sup 17/ ecm/sup 2/, while were remarkably smaller than that of Pyrex glass of 0.18 % shrinkage. Precision of the measurements in the density changes of the waste glass was lower than that of Pyrex glass possibly because of the inhomogeneity of the waste glass

Rapid bioassay method for estimation of 90Sr in urine samples by liquid scintillation counting

International Nuclear Information System (INIS)

Wankhede, Sonal; Chaudhary, Seema; Sawant, Pramilla D.

2018-01-01

Radiostrontium (Sr) is a by-product of the nuclear fission of uranium and plutonium in nuclear reactors and is an important radionuclide in spent nuclear fuel and radioactive waste. Rapid bioassay methods are required for estimating Sr in urine following internal contamination. Decision regarding medical intervention, if any can be based upon the results of urinalysis. The present method used at Bioassay Laboratory, Trombay is by Solid Extraction Chromatography (SEC) technique. The Sr separated from urine sample is precipitated as SrCO 3 and analyzed gravimetrically. However, gravimetric procedure is time consuming and therefore, in the present study, feasibility of Liquid Scintillation Counting for direct detection of radiostrontium in effluent was explored. The results obtained in the present study were compared with those obtained using gravimetric method

Selection of gonadotrophin surge attenuating factor phage antibodies by bioassay.

Science.gov (United States)

Sorsa-Leslie, Tarja; Mason, Helen D; Harris, William J; Fowler, Paul A

2005-09-26

We aimed to combine the generation of "artificial" antibodies with a rat pituitary bioassay as a new strategy to overcome 20 years of difficulties in the purification of gonadotrophin surge-attenuating factor (GnSAF). A synthetic single-chain antibody (Tomlinson J) phage display library was bio-panned with partially purified GnSAF produced by cultured human granulosa/luteal cells. The initial screening with a simple binding immunoassay resulted in 8 clones that were further screened using our in-vitro rat monolayer bioassay for GnSAF. Initially the antibodies were screened as pooled phage forms and subsequently as individual, soluble, single-chain antibody (scAbs) forms. Then, in order to improve the stability of the scAbs for immunopurification purposes, and to widen the range of labelled secondary antibodies available, these were engineered into full-length human immunoglobulins. The immunoglobulin with the highest affinity for GnSAF and a previously described rat anti-GnSAF polyclonal antiserum was then used to immunopurify bioactive GnSAF protein. The two purified preparations were electrophoresed on 1-D gels and on 7 cm 2-D gels (pH 4-7). The candidate GnSAF protein bands and spots were then excised for peptide mass mapping. Three of the scAbs recognised GnSAF bioactivity and subsequently one clone of the purified scAb-derived immunoglobulin demonstrated high affinity for GnSAF bioactivity, also binding the molecule in such as way as to block its bioactivity. When used for repeated immunopurification cycles and then Western blot, this antibody enabled the isolation of a GnSAF-bioactive protein band at around 66 kDa. Similar results were achieved using the rat anti-GnSAF polyclonal antiserum. The main candidate molecules identified from the immunopurified material by excision of 2-D gel protein spots was human serum albumin precursor and variants. This study demonstrates that the combination of bioassay and phage display technologies is a powerful tool in the

High insulation foam glass material from waste cathode ray tube panel glass

DEFF Research Database (Denmark)

König, Jakob; Petersen, Rasmus Rosenlund; Yue, Yuanzheng

. In general CRT consists of two types of glasses: barium/strontium containing glass (panel glass) and lead containing glass (funnel and panel glass). In this work we present the possibility to produce high performance insulation material from the recycled lead-free glass. We studied the influence of foaming...... between 750 and 850°C. We investigated the influence of milling time, particle size, foaming and oxidizing agent concentrations, temperature and time on the foaming process, foam density, foam porosity and homogeneity. Only moderate foaming was observed in carbon containing samples, while the addition...... of the oxidizing agent greatly improved the foaming quality. The results showed that the amount of oxygen available from the glass is not sufficient to combust all of the added carbon, therefore, additional oxygen was supplied via manganese reduction. In general, a minimum in the foam glass density was observed...

Propuesta de manual para la administración de contratos de servicios de consultoría en obras viales

OpenAIRE

Aronés Barbarán, Eddie Enzo

2014-01-01

La tesis tiene como objetivo aportar con un manual de administración de contratos de consultaría de obras viales. Para ello, se exponen los conceptos básicos de la inversión pública, los procesos de selección y de la contratación que el consultor llevará a cabo, así como el estudio de preinversión o definitivo. Finalmente, se intenta ofrecer una guía consolidada y descriptiva de las actividades secuenciales en la gestión de obras de infraestructura pública enfocada en los estudios de preinver...

Particle-stabilized oscillating diver: a self-assembled responsive capsule

DEFF Research Database (Denmark)

Tavacoli, Joe; Thijssen, Job H. J.; Clegg, Paul S.

2011-01-01

We report the experimental discovery of a self-assembled capsule, with density set by interfacial glass beads and an internal bubble, that automatically performs regular oscillations up and down a vial in response to a temperature gradient. Similar composites featuring interfacial particles...

Magnetic Glass Ceramics by Sintering of Borosilicate Glass and Inorganic Waste

Directory of Open Access Journals (Sweden)

Inès M. M. M. Ponsot

2014-07-01

Full Text Available Ceramics and glass ceramics based on industrial waste have been widely recognized as competitive products for building applications; however, there is a great potential for such materials with novel functionalities. In this paper, we discuss the development of magnetic sintered glass ceramics based on two iron-rich slags, coming from non-ferrous metallurgy and recycled borosilicate glass. The substantial viscous flow of the glass led to dense products for rapid treatments at relatively low temperatures (900–1000 °C, whereas glass/slag interactions resulted in the formation of magnetite crystals, providing ferrimagnetism. Such behavior could be exploited for applying the obtained glass ceramics as induction heating plates, according to preliminary tests (showing the rapid heating of selected samples, even above 200 °C. The chemical durability and safety of the obtained glass ceramics were assessed by both leaching tests and cytotoxicity tests.

Bioactive Glass and Glass-Ceramic Scaffolds for Bone Tissue Engineering

Directory of Open Access Journals (Sweden)

Aldo R. Boccaccini

2010-07-01

Full Text Available Traditionally, bioactive glasses have been used to fill and restore bone defects. More recently, this category of biomaterials has become an emerging research field for bone tissue engineering applications. Here, we review and discuss current knowledge on porous bone tissue engineering scaffolds on the basis of melt-derived bioactive silicate glass compositions and relevant composite structures. Starting with an excerpt on the history of bioactive glasses, as well as on fundamental requirements for bone tissue engineering scaffolds, a detailed overview on recent developments of bioactive glass and glass-ceramic scaffolds will be given, including a summary of common fabrication methods and a discussion on the microstructural-mechanical properties of scaffolds in relation to human bone (structure-property and structure-function relationship. In addition, ion release effects of bioactive glasses concerning osteogenic and angiogenic responses are addressed. Finally, areas of future research are highlighted in this review.

Bioassays for TSH Receptor Autoantibodies, from FRTL-5 Cells to TSH Receptor-LH/CG Receptor Chimeras: The Contribution of Leonard D. Kohn.

Science.gov (United States)

Giuliani, Cesidio; Saji, Motoyasu; Bucci, Ines; Napolitano, Giorgio

2016-01-01

Since the discovery 60 years ago of the "long-acting thyroid stimulator" by Adams and Purves, great progress has been made in the detection of thyroid-stimulating hormone (TSH) receptor (TSHR) autoantibodies (TRAbs) in Graves' disease. Today, commercial assays are available that can detect TRAbs with high accuracy and provide diagnostic and prognostic evaluation of patients with Graves' disease. The present review focuses on the development of TRAbs bioassays, and particularly on the role that Leonard D. Kohn had in this. Indeed, 30 years ago, the Kohn group developed a bioassay based on the use of FRTL-5 cells that was characterized by high reproducibility, feasibility, and diagnostic accuracy. Using this FRTL-5 bioassay, Kohn and his colleagues were the first to develop monoclonal antibodies (moAbs) against the TSHR. Furthermore, they demonstrated the multifaceted functional nature of TRAbs in patients with Graves' disease, with the identification of stimulating and blocking TRAbs, and even antibodies that activated pathways other than cAMP. After the cloning of the TSHR, the Kohn laboratory constructed human TSHR-rat luteinizing hormone/chorionic gonadotropin receptor chimeras. This paved the way to a new bioassay based on the use of non-thyroid cells transfected with the Mc4 chimera. The new Mc4 bioassay is characterized by high diagnostic and prognostic accuracy, greater than for other assays. The availability of a commercial kit based on the Mc4 chimera is spreading the use of this assay worldwide, indicating its benefits for these patients with Graves' disease. This review also describes the main contributions made by other researchers in TSHR molecular biology and TRAbs assay, especially with the development of highly potent moAbs. A comparison of the diagnostic accuracies of the main TRAbs assays, as both immunoassays and bioassays, is also provided.

Bioactive glasses and glass-ceramics

Directory of Open Access Journals (Sweden)

de Aza, P. N.

2007-04-01

Full Text Available Since the late 1960´s, a great interest in the use of bioceramic materials for biomedical applications has been developed. In a previous paper, the authors reviewed crystalline bioceramic materials “sensus stricto”, it is to say, those ceramic materials, constituted for non-metallic inorganic compounds, crystallines and consolidates by thermal treatment of powders at high temperature. In the present review, the authors deal with those called bioactive glasses and glassceramics. Although all of them are also obtained by thermal treatment at high temperature, the first are amorphous and the second are obtained by devitrification of a glass, although the vitreous phase normally prevails on the crystalline phases. After an introduction to the concept of bioactive materials, a short historical review of the bioactive glasses development is made. Its preparation, reactivity in physiological media, mechanism of bonding to living tissues and mechanical strength of the bone-implant interface is also reported. Next, the concept of glass-ceramic and the way of its preparation are exposed. The composition, physicochemical properties and biological behaviour of the principal types of bioactive glasses and glass-ceramic materials: Bioglass®, Ceravital®, Cerabone®, Ilmaplant® and Bioverit® are also reviewed. Finally, a short review on the bioactive-glass coatings and bioactive-composites and most common uses of bioactive-glasses and glass-ceramics are carried out too.

Desde finales de los años sesenta, se ha despertado un gran interés por el uso de los materiales biocerámicos para aplicaciones biomédicas. En un trabajo previo, los autores hicieron una revisión de los denominados materiales biocerámicos cristalinos en sentido estricto, es decir, de aquellos materiales, constituidos por compuestos inorgánicos no metálicos, cristalinos y consolidados mediante tratamientos térmicos a altas temperaturas. En el presente trabajo, los autores

Cancer risk assessment of polycyclic aromatic hydrocarbon contaminated soils determined using bioassay-derived levels of benzo[a]pyrene equivalents.

Science.gov (United States)

Lemieux, Christine L; Long, Alexandra S; Lambert, Iain B; Lundstedt, Staffan; Tysklind, Mats; White, Paul A

2015-02-03

Here we evaluate the excess lifetime cancer risk (ELCR) posed by 10 PAH-contaminated soils using (i) the currently advocated, targeted chemical-specific approach that assumes dose additivity for carcinogenic PAHs and (ii) a bioassay-based approach that employs the in vitro mutagenic activity of the soil fractions to determine levels of benzo[a]pyrene equivalents and, by extension, ELCR. Mutagenic activity results are presented in our companion paper.1 The results show that ELCR values for the PAH-containing fractions, determined using the chemical-specific approach, are generally (i.e., 8 out of 10) greater than those calculated using the bioassay-based approach; most are less than 5-fold greater. Only two chemical-specific ELCR estimates are less than their corresponding bioassay-derived values; differences are less than 10%. The bioassay-based approach, which permits estimation of ELCR without a priori knowledge of mixture composition, proved to be a useful tool to evaluate the chemical-specific approach. The results suggest that ELCR estimates for complex PAH mixtures determined using a targeted, chemical-specific approach are reasonable, albeit conservative. Calculated risk estimates still depend on contentious PEFs and cancer slope factors. Follow-up in vivo mutagenicity assessments will be required to validate the results and their relevance for human health risk assessment of PAH-contaminated soils.

Lanthanide-doped upconverting phosphors for bioassay and therapy

Science.gov (United States)

Guo, Huichen; Sun, Shiqi

2012-10-01

Lanthanide-doped fluorescent materials have gained increasing attention in recent years due to their unique luminescence properties which have led to their use in wide-ranging fields including those of biological applications. Aside from being used as agents for in vivo imaging, lanthanide-doped fluorescent materials also present many advantages for use in bioassays and therapy. In this review, we summarize the applications of lanthanide-doped up-converting phosphors (UCPs) in protein and gene detection, as well as in photodynamic and gene therapy in recent years, and outline their future potential in biological applications. The current report could serve as a reference for researchers in relevant fields.

Glass and vitrification

International Nuclear Information System (INIS)

Barton, J.L.; Vacher, R.; Moncouyoux, J.P.; Vernaz, E.

1997-01-01

Most glasses used as materials are oxides glasses that are produced by a quick quench of a liquid. Glasses are characterized by the absence of periodicity in the atomic arrangements, they do not have symmetries and do not present order over a long distance. This series of 4 short articles present: 1) the properties of glass and its industrial story, 2) the glass structure, 3) a forty years long story of glass as dies used to confine wastes and 4) the methodology used to study the behaviour of glass over very long periods of time. This methodology is based on 5 steps: 1) define and specify the material to study (the prediction of long term alteration of a material is nonsense unless you know well its initial properties), 2) identify all the alteration processes that are likely to happen, determine their kinetics and the influence of environmental parameters, 3) develop mathematical models in order to simulate long-term behaviour of glasses, 4) determine the release rates of the radionuclides confined in the glass, and 5) validate data and models, it is not possible to expect a complete validation of a model that will be extrapolated over tens of thousands of years, nevertheless some ways of validation can lead to a satisfactory level of confidence taking into account reasonable uncertainties. (A.C.)

Glass formation, properties, and structure of soda-yttria-silicate glasses

Science.gov (United States)

Angel, Paul W.; Hann, Raiford E.

1991-01-01

The glass formation region of the soda yttria silicate system was determined. The glasses within this region were measured to have a density of 2.4 to 3.1 g/cu cm, a refractive index of 1.50 to 1.60, a coefficient of thermal expansion of 7 x 10(exp -6)/C, softening temperatures between 500 and 780 C, and Vickers hardness values of 3.7 to 5.8 GPa. Aqueous chemical durability measurements were made on select glass compositions while infrared transmission spectra were used to study the glass structure and its effect on glass properties. A compositional region was identified which exhibited high thermal expansion, high softening temperatures, and good chemical durability.

Glass formation, properties and structure of soda-yttria-silica glasses

Science.gov (United States)

Angel, Paul W.; Hann, Raiford E.

1992-01-01

The glass formation region of the soda yttria silicate system was determined. The glasses within this region were measured to have a density of 2.4 to 3.1 g/cu cm, a refractive index of 1.50 to 1.60, a coefficient of thermal expansion of 7 x 10(exp -6)/C, softening temperatures between 500 and 780 C, and Vickers hardness values of 3.7 to 5.8 GPa. Aqueous chemical durability measurements were made on select glass compositions while infrared transmission spectra were used to study the glass structure and its effect on glass properties. A compositional region was identified which exhibited high thermal expansion, high softening temperatures, and good chemical durability.

Production of glass or glass-ceramic to metal seals with the application of pressure

Science.gov (United States)

Kelly, Michael D.; Kramer, Daniel P.

1987-11-10

In a process for preparing a glass or glass-ceramic to metal seal comprising contacting the glass with the metal and heat-treating the glass and metal under conditions whereby the glass to metal seal is effected and, optionally, the glass is converted to a glass-ceramic, an improvement comprises carrying out the heat-treating step using hot isostatic pressing.

Bioassay for uranium mill tailings

International Nuclear Information System (INIS)

Tschaeche, A.N.

1986-01-01

Uranium mill tailings are composed of fine sand that contains, among other things, some uranium (U/sup 238/ primarily), and all of the uranium daughters starting with /sup 230/Th that are left behind after the usable uranium is removed in the milling process. Millions of pounds of tailings are and continue to be generated at uranium mills around the United States. Discrete uranium mill tailings piles exist near the mills. In addition, the tailings materials were used in communities situated near mill sites for such purposes as building materials, foundations for buildings, pipe runs, sand boxes, gardens, etc. The Uranium Mill Tailings Remedial Action Project (UMTRAP) is a U.S. Department of Energy Program designed with the intention of removing or stabilizing the mill tailings piles and the tailings used to communities so that individuals are not exposed above the EPA limits established for such tailings materials. This paper discusses the bioassay programs that are established for workers who remove tailings from the communities in which they are placed

Glass leaching performance

International Nuclear Information System (INIS)

Chick, L.A.; Turcotte, R.P.

1983-05-01

Current understanding of the leaching performance of high-level nuclear waste (HLW) glass is summarized. The empirical model of waste glass leaching behavior developed shows that at high water flow rates the glass leach rate is kinetically limited to a maximum value. At intermediate water flow rates, leaching is limited by the solution concentration of silica and decreases with decreasing water flow rates. Release of soluble elements is controlled by silica dissolution because silica forms the binding network of the glass. At low water flow rates, mass loss rates reach values controlled by formation rates of alteration minerals, or by diffusion of dissolution products through essentially stagnant water. The parameters reviewed with respect to their quantifiable influence on leaching behavior include temperature, pH, leachant composition, glass composition, thermal history, and radiation. Of these, temperature is most important since the rate of mass loss approximately doubles with each 10 0 C increase in dilute solutions. The pH has small effects within the 4 to 10 range. The chemical composition of the leachant is most important with regard to its influence on alteration product formation. Glass composition exhibits the largest effects at high flow rates where improved glasses leach from ten to thirty times slower than glass 76 to 68. The effects of the thermal history (devitrification) of the glass are not likely to be significant. Radiation effects are important primarily in that radiolysis can potentially drive pH values to less than 4. Radiation damage to the glass causes insignificant changes in leaching performance

Friction behavior of glass and metals in contact with glass in various environments

Science.gov (United States)

Buckley, D. H.

1973-01-01

Sliding friction experiments have been conducted for heat-resistant glass and metals in contact with glass. These experiments were conducted in various environments including vacuum, moist air, dry air, octane, and stearic acid in hexadecane. Glass exhibited a higher friction force in moist air than it did in vacuum when in sliding contact with itself. The metals, aluminum, iron, and gold, all exhibited the same friction coefficient when sliding on glass in vacuum as glass sliding on glass. Gold-to-glass contacts were extremely sensitive to the environment despite the relative chemical inertness of gold.

Glass Property Data and Models for Estimating High-Level Waste Glass Volume

Energy Technology Data Exchange (ETDEWEB)

Vienna, John D.; Fluegel, Alexander; Kim, Dong-Sang; Hrma, Pavel R.

2009-10-05

This report describes recent efforts to develop glass property models that can be used to help estimate the volume of high-level waste (HLW) glass that will result from vitrification of Hanford tank waste. The compositions of acceptable and processable HLW glasses need to be optimized to minimize the waste-form volume and, hence, to save cost. A database of properties and associated compositions for simulated waste glasses was collected for developing property-composition models. This database, although not comprehensive, represents a large fraction of data on waste-glass compositions and properties that were available at the time of this report. Glass property-composition models were fit to subsets of the database for several key glass properties. These models apply to a significantly broader composition space than those previously publised. These models should be considered for interim use in calculating properties of Hanford waste glasses.

Glass Property Data and Models for Estimating High-Level Waste Glass Volume

International Nuclear Information System (INIS)

Vienna, John D.; Fluegel, Alexander; Kim, Dong-Sang; Hrma, Pavel R.

2009-01-01

This report describes recent efforts to develop glass property models that can be used to help estimate the volume of high-level waste (HLW) glass that will result from vitrification of Hanford tank waste. The compositions of acceptable and processable HLW glasses need to be optimized to minimize the waste-form volume and, hence, to save cost. A database of properties and associated compositions for simulated waste glasses was collected for developing property-composition models. This database, although not comprehensive, represents a large fraction of data on waste-glass compositions and properties that were available at the time of this report. Glass property-composition models were fit to subsets of the database for several key glass properties. These models apply to a significantly broader composition space than those previously publised. These models should be considered for interim use in calculating properties of Hanford waste glasses.

An aggregated perylene-based broad-spectrum, efficient and label-free quencher for multiplexed fluorescent bioassays.

Science.gov (United States)

Liu, Tao; Hu, Rong; Lv, Yi-Fan; Wu, Yuan; Liang, Hao; Huan, Shuang-Yan; Zhang, Xiao-Bing; Tan, Weihong; Yu, Ru-Qin

2014-08-15

Fluorescent sensing systems based on the quenching of fluorophores have found wide applications in bioassays. An efficient quencher will endow the sensing system a high sensitivity. The frequently used quenchers are based on organic molecules or nanomaterials, which usually need tedious synthesizing and modifying steps, and exhibit different quenching efficiencies to different fluorophores. In this work, we for the first time report that aggregated perylene derivative can serve as a broad-spectrum and label-free quencher that is able to efficiently quench a variety of fluorophores, such as green, red and far red dyes labeled on DNA. By choosing nucleases as model biomolecules, such a broad-spectrum quencher was then employed to construct a multiplexed bioassay platform through a label-free manner. Due to the high quenching efficiency of the aggregated perylene, the proposed platform could detect nuclease with high sensitivity, with a detection limit of 0.03U/mL for EcoRV, and 0.05U/mL for EcoRI. The perylene quencher does not affect the activity of nuclease, which makes it possible to design post-addition type bioassay platform. Moreover, the proposed platform allows simultaneous and multicolor analysis of nucleases in homogeneous solution, demonstrating its value of potential application in rapid screening of multiple bio-targets. Copyright © 2014 Elsevier B.V. All rights reserved.

Can painted glass felt or glass fibre cloth be used as vapour barrier?

DEFF Research Database (Denmark)

El-Khattam, Amira; Andersen, Mie Them; Hansen, Kurt Kielsgaard

2014-01-01

In most Nordic homes the interior surfaces of walls and ceilings have some kind of surface treatment for aesthetical reasons. The treatments can for example be glass felt or glass fibre cloth which are painted afterwards. To evaluate the hygrothermal performance of walls and ceilings...... treatments. The surface treatments were glass felt or glass fibre cloth with different types of paints or just paint. The paint types were acrylic paint and silicate paint. The results show that the paint type has high influence on the water vapour resistance while the underlay i.e. glass felt or glass fibre...... acrylic paint on glass felt or glass fibre cloth cannot be used instead of a vapour barrier....

Numerical study of the glass-glass transition in short-ranged attractive colloids

International Nuclear Information System (INIS)

Zaccarelli, Emanuela; Sciortino, Francesco; Tartaglia, Piero

2004-01-01

We report extensive numerical simulations in the glass region for a simple model of short-ranged attractive colloids, the square well model. We investigate the behaviour of the density autocorrelation function and of the static structure factor in the region of temperatures and packing fractions where a glass-glass transition is expected according to theoretical predictions. We strengthen our observations by studying both waiting time and history dependence of the numerical results. We provide evidence supporting the possibility that activated bond-breaking processes destabilize the attractive glass, preventing the full observation of a sharp glass-glass kinetic transition

Studies on Bi-Sr-Ca-Cu-O glasses and superconducting glass ceramics

International Nuclear Information System (INIS)

Singh, R.; Zacharias, E.

1991-01-01

Bi-Sr-Ca-Cu-O glasses and glass ceramics of various compositions were synthesised. The glass transition temperature varies from 396 to 422degC depending on the glass composition. The bulk glass ceramics of 4334, 4336, 2223 and 4246 compositions show superconductivity when the corresponding glass samples were heat-treated in air at 820degC for 3, 9, 12 and 24 h respectively. X-ray diffraction studies show that the superconducting phase present in all these compositions is Bi 2 Sr 2 Ca 1 Cu 2 O x . The 4334 glass ceramic is almost a single-phase material with a preferred orientation such that the c axis is normal to the sample surface. The 2223 glass ceramic has a higher T c (onset) than the other three compositions indicating the presence of high T c phase (110 K) also. ESR studies on the glass samples indicate the existence of Cu 2+ . The effect of heat treatment on ESR shows that the intensity of resonance decreases with increase in heat-treatment duration. This effect is more pronounced for the 4334 and 2223 compositions. The advantages of synthesizing superconducting materials by glass route are discussed in view of practical applications. (author). 9 refs., 6 figs

Spin glasses

CERN Document Server

Bovier, Anton

2007-01-01

Spin glass theory is going through a stunning period of progress while finding exciting new applications in areas beyond theoretical physics, in particular in combinatorics and computer science. This collection of state-of-the-art review papers written by leading experts in the field covers the topic from a wide variety of angles. The topics covered are mean field spin glasses, including a pedagogical account of Talagrand's proof of the Parisi solution, short range spin glasses, emphasizing the open problem of the relevance of the mean-field theory for lattice models, and the dynamics of spin glasses, in particular the problem of ageing in mean field models. The book will serve as a concise introduction to the state of the art of spin glass theory, usefull to both graduate students and young researchers, as well as to anyone curious to know what is going on in this exciting area of mathematical physics.

A method for making a glass supported system, such glass supported system, and the use of a glass support therefor

NARCIS (Netherlands)

Unnikrishnan, S.; Jansen, Henricus V.; Berenschot, Johan W.; Fazal, I.; Louwerse, M.C.; Mogulkoc, B.; Sanders, Remco G.P.; de Boer, Meint J.; Elwenspoek, Michael Curt

2008-01-01

The invention relates to a method for making a glass supported micro or nano system, comprising the steps of: i) providing a glass support; ii) mounting at least one system on at least one glass support; and iii) bonding the system to the glass support, such that the system is circumferentially

Development of Assessment Tools for Evaluation of the Benefits of DNAPL Source Zone Treatment

Science.gov (United States)

2008-09-01

oxidation (NRC 1997; Pennell and Abriola 1997) (see Table 1). 8 Although each of the above technologies may present distinct advantages and...pumping of extraction wells located along a plane perpendicular to groundwater flow. Although this approach offers the advantage of integrating...ml of IPA in glass auto sampler vials. A surfactant trap, consisting of a glass inlet liner packed with a 3-cm bed of 80- 100 mesh Porpak Q ( Alltech

Determination of an Environmental Background Level of Sr-90 in Urine for the Hanford Bioassay Program

International Nuclear Information System (INIS)

Antonio, Cheryl L.; Rivard, James W.

2009-01-01

During the decommissioning and maintenance of some of the facilities at the U.S. Department of Energy Hanford Site in Washington State, workers have potential for a 90Sr intake. However, because of worldwide radioactive fallout, 90Sr is present in our environment, and can be detectable in routine urine bioassay samples. It is important for the Hanford Site bioassay program to discern an occupational intake from a non-occupational environmental one. A detailed study of the background 90Sr in the urine of unexposed Hanford workers was performed. A survey of the Hanford Site bioassay database found 128 Hanford workers who were hired between 1997 and 2002 and who had a very low potential for an occupational exposure prior to the baseline strontium urinalysis. Each urinalysis sample represented excretion during an approximate 24-hr period. The arithmetic mean value for the 128 pre-exposure baselines was 3.6 ± 5.1 mBq d-1. The 90Sr activities in urine varied from -12 to 20 mBq. The 99th percentile result was 16.4 mBqd-1, which was interpreted to mean that 1% of Hanford workers not occupationally exposed to strontium might exceed 16.4 mBq d-1.

Binary eutectic clusters and glass formation in ideal glass-forming liquids

International Nuclear Information System (INIS)

Lu, Z. P.; Shen, J.; Xing, D. W.; Sun, J. F.; Liu, C. T.

2006-01-01

In this letter, a physical concept of binary eutectic clusters in 'ideal' glass-forming liquids is proposed based on the characteristics of most well-known bulk metallic glasses (BMGs). The authors approach also includes the treatment of binary eutectic clusters as basic units, which leads to the development of a simple but reliable method for designing BMGs more efficiently and effectively in these unique glass-forming liquids. As an example, bulk glass formers with superior glass-forming ability in the Zr-Ni-Cu-Al and Zr-Fe-Cu-Al systems were identified with the use of the strategy